Shockwaves Cause Synaptic Degeneration in Cultured Neurons

DTIC Science & Technology

2009-11-02

constructed of delrin. A piezoresistive pressure sensor (Endevco Model 8530C) was mounted flush with the plate, coaxial with the center of the gene gun ...biolostic gene gun to deliver shockwaves to cultured hippocampal or cortical neurons. These cultured cells form abundant synapses in vitro, and after a 24-48...neurons, we used a biolostic gene gun to deliver shockwaves to cultured hippocampal or cortical neurons. These cultured cells form abundant synapses in

In vivo effect of shock-waves on the healing of fractured bone.

PubMed

Augat, P; Claes, L; Suger, G

1995-10-01

In a controlled animal experiment we attempted to clarify the question of whether there is a stimulating effect of extracorporeal shock-waves on the repair process of fractured long bones. As a fracture model we used an osteotomy in the diaphysis of the ovine tibia and an external fixation device. Shock-wave treatment at two levels of intensity and with four different numbers of applied shocks was performed with an electromagnetic acoustic source. Healing of the osteotomized bone was evaluated by biomechanical and radiological investigations on the whole bone as well as on bone sections from areas of the fracture gap and the periosteal fracture callus. We found a non-significant tendency to deterioration of the fracture healing with increasing shock-wave intensities. The study of treatment parameters led neither to significantly different biomechanical outcomes nor to altered radiological results in comparison to the untreated control group. RELEVANCE:--While we cannot comment upon the effectiveness of extracorporeal shock-waves in the delayed treatment of fractures or pseudarthrosis, our results suggest that shock-waves have no beneficial effect in acute fracture repair.

A cumulative shear mechanism for tissue damage initiation in shock-wave lithotripsy.

PubMed

Freund, Jonathan B; Colonius, Tim; Evan, Andrew P

2007-09-01

Evidence suggests that inertial cavitation plays an important role in the renal injury incurred during shock-wave lithotripsy. However, it is unclear how tissue damage is initiated, and significant injury typically occurs only after a sufficient dose of shock waves. Although it has been suggested that shock-induced shearing might initiate injury, estimates indicate that individual shocks do not produce sufficient shear to do so. In this paper, we hypothesize that the cumulative shear of the many shocks is damaging. This mechanism depends on whether there is sufficient time between shocks for tissue to relax to its unstrained state. We investigate the mechanism with a physics-based simulation model, wherein the basement membranes that define the tubules and vessels in the inner medulla are represented as elastic shells surrounded by viscous fluid. Material properties are estimated from in-vitro tests of renal basement membranes and documented mechanical properties of cells and extracellular gels. Estimates for the net shear deformation from a typical lithotripter shock (approximately 0.1%) are found from a separate dynamic shock simulation. The results suggest that the larger interstitial volume (approximately 40%) near the papilla tip gives the tissue there a relaxation time comparable to clinical shock delivery rates (approximately 1 Hz), thus allowing shear to accumulate. Away from the papilla tip, where the interstitial volume is smaller (approximately 20%), the model tissue relaxes completely before the next shock would be delivered. Implications of the model are that slower delivery rates and broader focal zones should both decrease injury, consistent with some recent observations.

Explosively driven two-shockwave tools with application to ejecta formation at the Los Alamos National Laboratory Proton Radiography Facility

NASA Astrophysics Data System (ADS)

Buttler, William

2013-06-01

We present the development of an explosively driven physics tool to generate two mostly uniaxial shockwaves. The tool is being used to extend single shockwave ejecta models to a subsequent shockwave event separated by a time interval on the order of a few microseconds. We explore the possibility of varying the amplitude of both the first and second shockwaves, and we apply the tool in experimental geometries on Sn with a surface roughness of Ra = 0 . 8 μ m. We then evaluate the tool further at the Los Alamos National Laboratory Proton Radiography (pRad) Facility in an application to Sn with larger scale perturbations of wavelength 550 μ m, and various amplitudes that gave wave-number amplitude products of η0 2 π / λ = { 3 / 4 , 1 / 2 , 1 / 4 , 1 / 8 } , where the perturbation amplitude is η0, and the wave-number k = 2 π / λ . The pRad data and velocimetry imply it should be possible to develop a second shock ejecta model based on unstable Richtmyer-Meshkov physics. In collaboration with David Oro, Fesseha Mariam, Alexander Saunders, Malcolm Andrews, Frank Cherne, James Hammerberg. Robert Hixson, Christopher Morris, Russell Olson, Dean Preston, Joseph Stone, Dale Tupa, and Wendy Vogan-McNeil, Los Alamos National Laboratory,

Bifocal reflector for electrohydraulic lithotripters.

PubMed

Prieto, F E; Loske, A M

1999-03-01

To describe the design and construction of a bifocal reflector that could be used in electrohydraulic extracorporeal shockwave lithotripters in order to increase their efficiency. The new reflector is obtained by joining two sectors of two rotationally symmetric ellipsoidal reflectors having different distances between their foci, which results in a bifocal composite reflector with the F1 foci in coincidence and the two F2 foci separated by a certain distance. As in conventional reflectors, shockwaves are generated by the electrical breakdown of water between two electrodes, located at the focus (F1) closest to the reflector. A prototype was constructed and tested in an experimental shockwave generator of our own make, using two different types of kidney-stone models, one to test the stone fragmentation abilities, and the other to test the stone pitting abilities. Fragmentation data for the new reflector were compared with those of a conventional ellipsoidal reflector tested on the same device. The new design appeared to be more efficient in breaking up both types of kidney-stone models than the conventional reflector. Pressure measurements were obtained with both reflectors using needle hydrophones. The physical background of shockwave reflection on both reflectors is also explained. With this new reflector, it could be possible, in principle, to reduce the treatment time of extracorporeal shockwave lithotripsy.

Al 1s-2p absorption spectroscopy of shock-wave heating and compression in laser-driven planar foil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sawada, H.; Regan, S. P.; Radha, P. B.

Time-resolved Al 1s-2p absorption spectroscopy is used to diagnose direct-drive, shock-wave heating and compression of planar targets having nearly Fermi-degenerate plasma conditions (T{sub e}{approx}10-40 eV, {rho}{approx}3-11 g/cm{sup 3}) on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. A planar plastic foil with a buried Al tracer layer was irradiated with peak intensities of 10{sup 14}-10{sup 15} W/cm{sup 2} and probed with the pseudocontinuum M-band emission from a point-source Sm backlighter in the range of 1.4-1.7 keV. The laser ablation process launches 10-70 Mbar shock waves into the CH/Al/CH target. The Al 1s-2p absorption spectramore » were analyzed using the atomic physic code PRISMSPECT to infer T{sub e} and {rho} in the Al layer, assuming uniform plasma conditions during shock-wave heating, and to determine when the heat front penetrated the Al layer. The drive foils were simulated with the one-dimensional hydrodynamics code LILAC using a flux-limited (f=0.06 and f=0.1) and nonlocal thermal-transport model [V. N. Goncharov et al., Phys. Plasmas 13, 012702 (2006)]. The predictions of simulated shock-wave heating and the timing of heat-front penetration are compared to the observations. The experimental results for a wide variety of laser-drive conditions and buried depths have shown that the LILAC predictions using f=0.06 and the nonlocal model accurately model the shock-wave heating and timing of the heat-front penetration while the shock is transiting the target. The observed discrepancy between the measured and simulated shock-wave heating at late times of the drive can be explained by the reduced radiative heating due to lateral heat flow in the corona.« less

Al 1s-2p Absorption Spectroscopy of Shock-Wave Heating and Compression in Laser-Driven Planar Foil

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sawada, H.; Regan, S.P.; Radha, P.B.

Time-resolved Al 1s-2p absorption spectroscopy is used to diagnose direct-drive, shock-wave heating and compression of planar targets having nearly Fermi-degenerate plasma conditions (Te ~ 10–40 eV, rho ~ 3–11 g/cm^3) on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. A planar plastic foil with a buried Al tracer layer was irradiated with peak intensities of 10^14–10^15 W/cm^2 and probed with the pseudocontinuum M-band emission from a point-source Sm backlighter in the range of 1.4–1.7 keV. The laser ablation process launches 10–70 Mbar shock waves into the CH/Al/CH target. The Al 1s-2p absorption spectra weremore » analyzed using the atomic physic code PRISMSPECT to infer Te and rho in the Al layer, assuming uniform plasma conditions during shock-wave heating, and to determine when the heat front penetrated the Al layer. The drive foils were simulated with the one-dimensional hydrodynamics code LILAC using a flux-limited (f =0.06 and f =0.1) and nonlocal thermal-transport model [V. N. Goncharov et al., Phys. Plasmas 13, 012702 (2006)]. The predictions of simulated shock-wave heating and the timing of heat-front penetration are compared to the observations. The experimental results for a wide variety of laser-drive conditions and buried depths have shown that the LILAC predictions using f = 0.06 and the nonlocal model accurately model the shock-wave heating and timing of the heat-front penetration while the shock is transiting the target. The observed discrepancy between the measured and simulated shock-wave heating at late times of the drive can be explained by the reduced radiative heating due to lateral heat flow in the corona.« less

Electrohydraulic Forming of Near-Net Shape Automotive Panels

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golovaschenko, Sergey F.

2013-09-26

The objective of this project was to develop the electrohydraulic forming (EHF) process as a near-net shape automotive panel manufacturing technology that simultaneously reduces the energy embedded in vehicles and the energy consumed while producing automotive structures. Pulsed pressure is created via a shockwave generated by the discharge of high voltage capacitors through a pair of electrodes in a liquid-filled chamber. The shockwave in the liquid initiated by the expansion of the plasma channel formed between two electrodes propagates towards the blank and causes the blank to be deformed into a one-sided die cavity. The numerical model of the EHFmore » process was validated experimentally and was successfully applied to the design of the electrode system and to a multi-electrode EHF chamber for full scale validation of the process. The numerical model was able to predict stresses in the dies during pulsed forming and was validated by the experimental study of the die insert failure mode for corner filling operations. The electrohydraulic forming process and its major subsystems, including durable electrodes, an EHF chamber, a water/air management system, a pulse generator and integrated process controls, were validated to be capable to operate in a fully automated, computer controlled mode for forming of a portion of a full-scale sheet metal component in laboratory conditions. Additionally, the novel processes of electrohydraulic trimming and electrohydraulic calibration were demonstrated at a reduced-scale component level. Furthermore, a hybrid process combining conventional stamping with EHF was demonstrated as a laboratory process for a full-scale automotive panel formed out of AHSS material. The economic feasibility of the developed EHF processes was defined by developing a cost model of the EHF process in comparison to the conventional stamping process.« less

Influence of sweeping detonation-wave loading on damage evolution during spallation loading of tantalum in both a planar and curved geometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, George Thompson III; Hull, Lawrence Mark; Livescu, Veronica

Widespread research over the past five decades has provided a wealth of experimental data and insight concerning the shock hardening, damage evolution, and the spallation response of materials subjected to square-topped shock-wave loading profiles. However, fewer quantitative studies have been conducted on the effect of direct, in-contact, high explosive (HE)-driven Taylor wave (unsupported shocks) loading on the shock hardening, damage evolution, or spallation response of materials. Systematic studies quantifying the effect of sweeping-detonation wave loading are yet sparser. In this study, the damage evolution and spallation response of Ta is shown to be critically dependent on the peak shock stress,more » the geometry of the sample (flat or curved plate geometry), and the shock obliquity during sweeping-detonation-wave shock loading. Sweepingwave loading in the flat-plate geometry is observed to: a) yield a lower spall strength than previously documented for 1-D supported-shock-wave loading, b) exhibit increased shock hardening as a function of increasing obliquity, and c) lead to an increased incidence of deformation twin formation with increasing shock obliquity. Sweeping-wave loading of a 10 cm radius curved Ta plate is observed to: a) lead to an increase in the shear stress as a function of increasing obliquity, b) display a more developed level of damage evolution, extensive voids and coalescence, and lower spall strength with obliquity in the curved plate than seen in the flat-plate sweeping-detonation wave loading for an equivalent HE loading, and c) no increased propensity for deformation twin formation with increasing obliquity as seen in the flat-plate geometry. The overall observations comparing and contrasting the flat versus curved sweeping-wave spall experiments with 1D loaded spallation behavior suggests a coupled influence of obliquity and geometry on dynamic shock-induced damage evolution and spall strength. Coupled experimental and modeling research to quantify the combined effects of sweeping-wave loading with increasingly complex sample geometries on the shockwave response of materials is clearly crucial to providing the basis for developing and thereafter validation of predictive modeling capability.« less

The TOPSHOCK study: Effectiveness of radial shockwave therapy compared to focused shockwave therapy for treating patellar tendinopath - design of a randomised controlled trial

PubMed Central

2011-01-01

Background Patellar tendinopathy is a chronic overuse injury of the patellar tendon that is especially prevalent in people who are involved in jumping activities. Extracorporeal Shockwave Therapy is a relatively new treatment modality for tendinopathies. It seems to be a safe and promising part of the rehabilitation program for patellar tendinopathy. Extracorporeal Shockwave Therapy originally used focused shockwaves. Several years ago a new kind of shockwave therapy was introduced: radial shockwave therapy. Studies that investigate the effectiveness of radial shockwave therapy as treatment for patellar tendinopathy are scarce. Therefore the aim of this study is to compare the effectiveness of focussed shockwave therapy and radial shockwave therapy as treatments for patellar tendinopathy. Methods/design The TOPSHOCK study (Tendinopathy Of Patella SHOCKwave) is a two-armed randomised controlled trial in which the effectiveness of focussed shockwave therapy and radial shockwave therapy are directly compared. Outcome assessors and patients are blinded as to which treatment is given. Patients undergo three sessions of either focused shockwave therapy or radial shockwave therapy at 1-week intervals, both in combination with eccentric decline squat training. Follow-up measurements are scheduled just before treatments 2 and 3, and 1, 4, 7 and 12 weeks after the final treatment. The main outcome measure is the Dutch VISA-P questionnaire, which asks for pain, function and sports participation in subjects with patellar tendinopathy. Secondary outcome measures are pain determined with a VAS during ADL, sports and decline squats, rating of subjective improvement and overall satisfaction with the treatment. Patients will also record their sports activities, pain during and after these activities, and concurrent medical treatment on a weekly basis in a web-based diary. Results will be analysed according to the intention-to-treat principle. Discussion The TOPSHOCK study is the first randomised controlled trial that directly compares the effectiveness of focused shockwave therapy and radial shockwave therapy, both in combination with eccentric decline squat training, for treating patellar tendinopathy. Trial registration Trial registration number NTR2774. PMID:21989041

Mesoscale simulations of shockwave energy dissipation via chemical reactions.

PubMed

Antillon, Edwin; Strachan, Alejandro

2015-02-28

We use a particle-based mesoscale model that incorporates chemical reactions at a coarse-grained level to study the response of materials that undergo volume-reducing chemical reactions under shockwave-loading conditions. We find that such chemical reactions can attenuate the shockwave and characterize how the parameters of the chemical model affect this behavior. The simulations show that the magnitude of the volume collapse and velocity at which the chemistry propagates are critical to weaken the shock, whereas the energetics in the reactions play only a minor role. Shock loading results in transient states where the material is away from local equilibrium and, interestingly, chemical reactions can nucleate under such non-equilibrium states. Thus, the timescales for equilibration between the various degrees of freedom in the material affect the shock-induced chemistry and its ability to attenuate the propagating shock.

Uniformity of cylindrical imploding underwater shockwaves at very small radii

NASA Astrophysics Data System (ADS)

Yanuka, D.; Rososhek, A.; Bland, S. N.; Krasik, Ya. E.

2017-11-01

We compare the convergent shockwaves generated from underwater, cylindrical arrays of copper wire exploded by multiple kilo-ampere current pulses on nanosecond and microsecond scales. In both cases, the pulsed power devices used for the experiments had the same stored energy (˜500 J) and the wire mass was adjusted to optimize energy transfer to the shockwave. Laser backlit framing images of the shock front were achieved down to the radius of 30 μm. It was found that even in the case of initial azimuthal non-symmetry, the shock wave self-repairs in the final stages of its motion, leading to a highly uniform implosion. In both these and previous experiments, interference fringes have been observed in streak and framing images as the shockwave approached the axis. We have been able to accurately model the origin of the fringes, which is due to the propagation of the laser beam diffracting off the uniform converging shock front. The dynamics of the shockwave and its uniformity at small radii indicate that even with only 500 J stored energies, this technique should produce pressures above 1010 Pa on the axis, with temperatures and densities ideal for warm dense matter research.

Semiempirical models for description of shear modulus in wide ranges of temperatures and pressures of shock compression

NASA Astrophysics Data System (ADS)

El'Kin, V. M.; Mikhailov, V. N.; Mikhailova, T. Yu.

2011-12-01

In this paper, we discuss the potentials of the Steinberg-Cochran-Guinan (SCG) and Burakovsky-Preston (BP) models for the description of the shear-modulus behavior at temperatures and pressures that arise behind the shock-wave front. A modernized variant of the SCG model is suggested, which reduces to the introduction of a free parameter and the representation of the model in the volume-temperature coordinates (( V, T) model). A systematic comparison is performed of all three models of shear modulus with experimental data and data of ab initio calculations for metals such as Al, Be, Cu, K, Na, Mg, Mo, W, and Ta in a wide range of pressures. In addition, for Al, Cu, Mo, W, and Ta there is performed a comparison with the known temperature dependences of the shear modulus and with the results of measurements of the velocities of longitudinal sound behind the shock-wave front. It is shown that in the original form the SCG and BP models give overestimated values of the shear modulus as compared to the data of ab initio calculations and shock-wave experiments. The ( V, T) model, due to the use of a free parameter, makes it possible to optimally describe the totality of experimental and calculated data. The same result is achieved in the case of the BP model after a redefining of its initial parameters. The adequate description of the shear modulus in the range of high intermediate pressures characteristic of the solid-phase states behind the shock-wave front is accompanied in both cases by the violation of the correct asymptotic behavior of the shear modulus at ultrahigh compressions which is originally laid into the SCG and BP models.

The resistance to deformation and facture of magnesium ma2-1 under shock-wave loading at 293 k and 823 k of the temperature

NASA Astrophysics Data System (ADS)

Garkushin, Gennady; Kanel, Gennady I.; Razorenov, Sergey V.

2012-03-01

The Hugoniot elastic limit and spall strength of Ma2-1 magnesium deformable alloy were measured at the sample thickness varied from 0.25 mm to 10 mm at room and elevated temperatures. By means of analysis of decay of an elastic precursor wave it is found that initial plastic strain rate decreases from 2×105 s-1 at distance of 0.25 mm to 103 s-1 at distance of 10 mm. The strain rate in plastic shock wave is by order of magnitude higher at the same value of the shear stress. The spall strength of the alloy grows with increasing the strain rate and decreases with approach to the solidus temperature.

International Shock-Wave Database: Current Status

NASA Astrophysics Data System (ADS)

Levashov, Pavel

2013-06-01

Shock-wave and related dynamic material response data serve for calibrating, validating, and improving material models over very broad regions of the pressure-temperature-density phase space. Since the middle of the 20th century vast amount of shock-wave experimental information has been obtained. To systemize it a number of compendiums of shock-wave data has been issued by LLNL, LANL (USA), CEA (France), IPCP and VNIIEF (Russia). In mid-90th the drawbacks of the paper handbooks became obvious, so the first version of the online shock-wave database appeared in 1997 (http://www.ficp.ac.ru/rusbank). It includes approximately 20000 experimental points on shock compression, adiabatic expansion, measurements of sound velocity behind the shock front and free-surface-velocity for more than 650 substances. This is still a useful tool for the shock-wave community, but it has a number of serious disadvantages which can't be easily eliminated: (i) very simple data format for points and references; (ii) minimalistic user interface for data addition; (iii) absence of history of changes; (iv) bad feedback from users. The new International Shock-Wave database (ISWdb) is intended to solve these and some other problems. The ISWdb project objectives are: (i) to develop a database on thermodynamic and mechanical properties of materials under conditions of shock-wave and other dynamic loadings, selected related quantities of interest, and the meta-data that describes the provenance of the measurements and material models; and (ii) to make this database available internationally through the Internet, in an interactive form. The development and operation of the ISWdb is guided by an advisory committee. The database will be installed on two mirrored web-servers, one in Russia and the other in USA (currently only one server is available). The database provides access to original experimental data on shock compression, non-shock dynamic loadings, isentropic expansion, measurements of sound speed in the Hugoniot state, and time-dependent free-surface or window-interface velocity profiles. Users are able to search the information in the database and obtain the experimental points in tabular or plain text formats directly via the Internet using common browsers. It is also possible to plot the experimental points for comparison with different approximations and results of equation-of-state calculations. The user can present the results of calculations in text or graphical forms and compare them with any experimental data available in the database. A short history of the shock-wave database will be presented and current possibilities of ISWdb will be demonstrated. Web-site of the project: http://iswdb.info. This work is supported by SNL contracts # 1143875, 1196352.

[Extracorporeal shock-wave therapy in the treatment of Peyronie's disease].

PubMed

Neĭmark, A I; Astakhov, Iu I; Sidor, M V

2004-01-01

The authors analyse the results of treatment of 28 patients with Peyronie's disease using extracorporeal shock-wave lithotripsy (ESWL) performed on Dornier U15 lithotriptor. A total of 2-6 sessions were made, maximal number--12. The efficacy was controlled by clinical indices and ultrasonic investigation (Doppler mapping of the blood flow). ESWL proved to be efficient in the treatment of Peyronie's disease (PD), primarily, in patients with early disease before appearance of severe fibroplastic alterations. Less plaque vascularization by energetic Doppler mapping due to ESWL is an important diagnostic criterion of PD treatment efficacy. Conservative treatment is not indicated in marked deformities and plaque calcification, erectile dysfunction. Moreover, any injection into the tunica albuginea, especially complicated by hematomas may be a damaging factor which triggers fibrous inflammation. Such patients should be treated surgically. If the patient is interested in immediate results or is not interested in continuation of sexual life, the treatment is prognostically uneffective. Thus, ESWL is an effective, safe method of PD treatment but requires further study and accumulation of clinical experience.

Meso-scale Computational Investigation of Polyurea Microstructure and Its Role in Shockwave Attenuation/dispersion

DTIC Science & Technology

2015-07-01

grained simulations of the formation of meso-segregated microstructure and its interaction with the shockwave is analyzed in the present work. It is...help identify these phenomena and processes, meso-scale coarse-grained simulations of the formation of meso-segregated microstructure and its...of shockwave-induced hard-domain densification. Keywords: Polyurea; Meso-scale; Coarse-grained simulations ; Shockwave attenuation; shockwave

Xenon Protects against Blast-Induced Traumatic Brain Injury in an In Vitro Model.

PubMed

Campos-Pires, Rita; Koziakova, Mariia; Yonis, Amina; Pau, Ashni; Macdonald, Warren; Harris, Katie; Edge, Christopher J; Franks, Nicholas P; Mahoney, Peter F; Dickinson, Robert

2018-04-15

The aim of this study was to evaluate the neuroprotective efficacy of the inert gas xenon as a treatment for patients with blast-induced traumatic brain injury in an in vitro laboratory model. We developed a novel blast traumatic brain injury model using C57BL/6N mouse organotypic hippocampal brain-slice cultures exposed to a single shockwave, with the resulting injury quantified using propidium iodide fluorescence. A shock tube blast generator was used to simulate open field explosive blast shockwaves, modeled by the Friedlander waveform. Exposure to blast shockwave resulted in significant (p < 0.01) injury that increased with peak-overpressure and impulse of the shockwave, and which exhibited a secondary injury development up to 72 h after trauma. Blast-induced propidium iodide fluorescence overlapped with cleaved caspase-3 immunofluorescence, indicating that shock-wave-induced cell death involves apoptosis. Xenon (50% atm) applied 1 h after blast exposure reduced injury 24 h (p < 0.01), 48 h (p < 0.05), and 72 h (p < 0.001) later, compared with untreated control injury. Xenon-treated injured slices were not significantly different from uninjured sham slices at 24 h and 72 h. We demonstrate for the first time that xenon treatment after blast traumatic brain injury reduces initial injury and prevents subsequent injury development in vitro. Our findings support the idea that xenon may be a potential first-line treatment for those with blast-induced traumatic brain injury.

Biologically inspired crack delocalization in a high strain-rate environment.

PubMed

Knipprath, Christian; Bond, Ian P; Trask, Richard S

2012-04-07

Biological materials possess unique and desirable energy-absorbing mechanisms and structural characteristics worthy of consideration by engineers. For example, high levels of energy dissipation at low strain rates via triggering of crack delocalization combined with interfacial hardening by platelet interlocking are observed in brittle materials such as nacre, the iridescent material in seashells. Such behaviours find no analogy in current engineering materials. The potential to mimic such toughening mechanisms on different length scales now exists, but the question concerning their suitability under dynamic loading conditions and whether these mechanisms retain their energy-absorbing potential is unclear. This paper investigates the kinematic behaviour of an 'engineered' nacre-like structure within a high strain-rate environment. A finite-element (FE) model was developed which incorporates the pertinent biological design features. A parametric study was carried out focusing on (i) the use of an overlapping discontinuous tile arrangement for crack delocalization and (ii) application of tile waviness (interfacial hardening) for improved post-damage behaviour. With respect to the material properties, the model allows the permutation and combination of a variety of different material datasets. The advantage of such a discontinuous material shows notable improvements in sustaining high strain-rate deformation relative to an equivalent continuous morphology. In the case of the continuous material, the shockwaves propagating through the material lead to localized failure while complex shockwave patterns are observed in the discontinuous flat tile arrangement, arising from platelet interlocking. The influence of the matrix properties on impact performance is investigated by varying the dominant material parameters. The results indicate a deceleration of the impactor velocity, thus delaying back face nodal displacement. A final series of FE models considered the identification of an optimized configuration as a function of tile waviness and matrix properties. In the combined model, the optimized configuration was capable of stopping the ballistic threat, thus indicating the potential for bioinspired toughened synthetic systems to defeat high strain-rate threats.

Biologically inspired crack delocalization in a high strain-rate environment

PubMed Central

Knipprath, Christian; Bond, Ian P.; Trask, Richard S.

2012-01-01

Biological materials possess unique and desirable energy-absorbing mechanisms and structural characteristics worthy of consideration by engineers. For example, high levels of energy dissipation at low strain rates via triggering of crack delocalization combined with interfacial hardening by platelet interlocking are observed in brittle materials such as nacre, the iridescent material in seashells. Such behaviours find no analogy in current engineering materials. The potential to mimic such toughening mechanisms on different length scales now exists, but the question concerning their suitability under dynamic loading conditions and whether these mechanisms retain their energy-absorbing potential is unclear. This paper investigates the kinematic behaviour of an ‘engineered’ nacre-like structure within a high strain-rate environment. A finite-element (FE) model was developed which incorporates the pertinent biological design features. A parametric study was carried out focusing on (i) the use of an overlapping discontinuous tile arrangement for crack delocalization and (ii) application of tile waviness (interfacial hardening) for improved post-damage behaviour. With respect to the material properties, the model allows the permutation and combination of a variety of different material datasets. The advantage of such a discontinuous material shows notable improvements in sustaining high strain-rate deformation relative to an equivalent continuous morphology. In the case of the continuous material, the shockwaves propagating through the material lead to localized failure while complex shockwave patterns are observed in the discontinuous flat tile arrangement, arising from platelet interlocking. The influence of the matrix properties on impact performance is investigated by varying the dominant material parameters. The results indicate a deceleration of the impactor velocity, thus delaying back face nodal displacement. A final series of FE models considered the identification of an optimized configuration as a function of tile waviness and matrix properties. In the combined model, the optimized configuration was capable of stopping the ballistic threat, thus indicating the potential for bioinspired toughened synthetic systems to defeat high strain-rate threats. PMID:21880614

Xenon Protects against Blast-Induced Traumatic Brain Injury in an In Vitro Model

PubMed Central

Campos-Pires, Rita; Koziakova, Mariia; Yonis, Amina; Pau, Ashni; Macdonald, Warren; Harris, Katie; Edge, Christopher J.; Franks, Nicholas P.; Mahoney, Peter F.

2018-01-01

Abstract The aim of this study was to evaluate the neuroprotective efficacy of the inert gas xenon as a treatment for patients with blast-induced traumatic brain injury in an in vitro laboratory model. We developed a novel blast traumatic brain injury model using C57BL/6N mouse organotypic hippocampal brain-slice cultures exposed to a single shockwave, with the resulting injury quantified using propidium iodide fluorescence. A shock tube blast generator was used to simulate open field explosive blast shockwaves, modeled by the Friedlander waveform. Exposure to blast shockwave resulted in significant (p < 0.01) injury that increased with peak-overpressure and impulse of the shockwave, and which exhibited a secondary injury development up to 72 h after trauma. Blast-induced propidium iodide fluorescence overlapped with cleaved caspase-3 immunofluorescence, indicating that shock-wave–induced cell death involves apoptosis. Xenon (50% atm) applied 1 h after blast exposure reduced injury 24 h (p < 0.01), 48 h (p < 0.05), and 72 h (p < 0.001) later, compared with untreated control injury. Xenon-treated injured slices were not significantly different from uninjured sham slices at 24 h and 72 h. We demonstrate for the first time that xenon treatment after blast traumatic brain injury reduces initial injury and prevents subsequent injury development in vitro. Our findings support the idea that xenon may be a potential first-line treatment for those with blast-induced traumatic brain injury. PMID:29285980

COMPARISON BETWEEN EXTRACORPOREAL SHOCK WAVE LITHOTRIPSY AT 120 AND 60 SHOCKWAVES PER MINUTE FOR TREATMENT OF URINARY STONES.

PubMed

Kashima, Soki; Horikawa, Yohei; Obara, Takashi; Muto, Yumina; Koizumi, Atsushi; Honma, Naoko; Akihama, Susumu; Shimoda, Naotake

2016-01-01

(Purpose) It has recently been suggested that a slow delivery rate of shockwaves by extracorporeal shock wave lithotripsy (SWL) improved treatment outcomes for urinary stones. We retrospectively analyzed the treatment outcomes of different shockwave delivery rates at 120 and 60 shockwaves per minute. (Patients and method) A total of 88 patients were treated at a fast delivery rate of 120 shockwaves per minute between July 2010 and April 2012, and 139 patients were treated at a slow delivery rate of 60 shockwaves per minute between May 2012 and May 2014 (n=227) using a Sonolith ® Praktis lithotripter. The treatment outcome of stone-free rate (SFR) after one SWL session was assessed at four weeks. (Result) SWL at 60 shockwaves per minute resulted in a significantly higher SFR compared with SWL at 120 shockwaves per minute (39.8% and 59.0%, respectively, p=0.0047), particularly for upper ureter (U1) stones (53.1% and 72.0%, respectively, p=0.028). Multivariate analysis showed that younger age, stone sizes of 10 mm or less, U1 stones, and slow delivery rate were significant predictors of a stone-free outcome. There were fewer adverse events after the delivery rate of 60 shockwaves per minute (p=0.058). (Conclusion) Our study suggests that SWL at 60 shockwaves per minute should be recommended to successfully treat urinary stones using the Sonolith ® Praktis lithotripter.

Modeling shockwaves and impact phenomena with Eulerian peridynamics

DOE PAGES

Silling, Stewart A.; Parks, Michael L.; Kamm, James R.; ...

2017-05-09

Most previous development of the peridynamic theory has assumed a Lagrangian formulation, in which the material model refers to an undeformed reference configuration. Here, an Eulerian form of material modeling is developed, in which bond forces depend only on the positions of material points in the deformed configuration. The formulation is consistent with the thermodynamic form of the peridynamic model and is derivable from a suitable expression for the free energy of a material. We show that the resulting formulation of peridynamic material models can be used to simulate strong shock waves and fluid response in which very large deformationsmore » make the Lagrangian form unsuitable. The Eulerian capability is demonstrated in numerical simulations of ejecta from a wavy free surface on a metal subjected to strong shock wave loading. The Eulerian and Lagrangian contributions to bond force can be combined in a single material model, allowing strength and fracture under tensile or shear loading to be modeled consistently with high compressive stresses. Furthermore, we demonstrate this capability in numerical simulation of bird strike against an aircraft, in which both tensile fracture and high pressure response are important.« less

Modeling shockwaves and impact phenomena with Eulerian peridynamics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silling, Stewart A.; Parks, Michael L.; Kamm, James R.

Most previous development of the peridynamic theory has assumed a Lagrangian formulation, in which the material model refers to an undeformed reference configuration. Here, an Eulerian form of material modeling is developed, in which bond forces depend only on the positions of material points in the deformed configuration. The formulation is consistent with the thermodynamic form of the peridynamic model and is derivable from a suitable expression for the free energy of a material. We show that the resulting formulation of peridynamic material models can be used to simulate strong shock waves and fluid response in which very large deformationsmore » make the Lagrangian form unsuitable. The Eulerian capability is demonstrated in numerical simulations of ejecta from a wavy free surface on a metal subjected to strong shock wave loading. The Eulerian and Lagrangian contributions to bond force can be combined in a single material model, allowing strength and fracture under tensile or shear loading to be modeled consistently with high compressive stresses. Furthermore, we demonstrate this capability in numerical simulation of bird strike against an aircraft, in which both tensile fracture and high pressure response are important.« less

Study on miss distance based on projectile shock wave sensor

NASA Astrophysics Data System (ADS)

Gu, Guohua; Cheng, Gang; Zhang, Chenjun; Zhou, Lei

2017-05-01

The paper establishes miss distance models based on physical characteristic of shock-wave. The aerodynamic theory shows that the shock-wave of flying super-sonic projectile is generated for the projectile compressing and expending its ambient atmosphere. It advances getting miss distance according to interval of the first sensors, which first catches shock-wave, to solve the problem such as noise filtering on severe background, and signals of amplifier vibration dynamic disposal and electromagnetism compatibility, in order to improves the precision and reliability of gathering wave N signals. For the first time, it can identify the kinds of pills and firing units automatically, measure miss distance and azimuth when pills are firing. Application shows that the tactics and technique index is advanced all of the world.

Heat, mass and force flows in supersonic shockwave interaction

NASA Astrophysics Data System (ADS)

Dixon, John Michael

There is no cost effective way to deliver a payload to space and, with rising fuel prices, currently the price to travel commercially is also becoming more prohibitive to the public. During supersonic flight, compressive shock waves form around the craft which could be harnessed to deliver an additional lift on the craft. Using a series of hanging plates below a lifting wing design, the total lift generated can be increased above conventional values, while still maintaining a similar lift-to-drag ratio. Here, we study some of the flows involved in supersonic shockwave interaction. This analysis uses ANSYS Fluent Computational Fluid Dynamics package as the modeler. Our findings conclude an increase of up to 30% lift on the modeled craft while maintaining the lift-to-drag profile of the unmodified lifting wing. The increase in lift when utilizing the shockwave interaction could increase transport weight and reduce fuel cost for space and commercial flight, as well as mitigating negative effects associated with supersonic travel.

Minimizing masses in explosively driven two-shockwave physics applications

NASA Astrophysics Data System (ADS)

Buttler, William; Cherne, Frank; Furlanetto, Michael; Payton, Jeremy; Stone, Joseph; Tabaka, Leonard; Vincent, Samuel

2015-06-01

We have experimentally investigated different two-shockwave high-explosives (HE) physics package designs to maximize the variability of the second shockwave peak stress, while minimizing the total HE load of the physics tool. A critical requirement is to also have a large radial diameter of the second shockwave to maintain its value as an HE driven two-shockwave drive. We have previously shown that we could vary the peak-stress of the second-shockwave with a 76 mm diameter HE lens driving different composite boosters of PBX 9501 and TNT. Here we report on our results with a 56- and 50-mm diameter HE lens driving Baritol. The results indicate that the 56-mm diameter HE lens works well, as does the Baritol, giving total HE loads of about 250 mg TNT equivalent explosives.

Determination of trajectories of fireballs using seismic network data

NASA Astrophysics Data System (ADS)

Ishihara, Y.

2006-12-01

Fireballs, Bolides, which are caused by high velocity passages of meteoroids through the atmosphere, generate shockwaves. Meteor shockwave provide us very important information (arrival time and amplitude) to study meteor physics. The shockwave arrival time data enable us to determine trajectories of the fireballs. On the other hand, the shockwave amplitude tells us size and ablation history of the meteoroid. Infrasound observation is one of the ways of detecting bolide shockwaves. However, we have no infrasound observational networks extends for large area with enough spatial distribution for determination of trajectories and estimate ablation histories. We have only a few infrasound arrays that have three or four elements, in the Japanese islands. Last decade, digital seismic networks are greatly improved for the purpose of monitoring micro earthquakes. Those seismic networks are quite sensitive for detecting micro ground vibration, and then those networks could detect not only seismic wave generated by earthquakes, but also ground oscillations generated by coupling of meteor shockwave with the ground near station. Last years, I analyses this kind of ground motion data recorded by seismic network, as meteor shockwave signals. For example, we estimate some great fireball's aerial path from arrival times of shockwaves (e.g., Ishihara et. al., 2003 Earth Planets, and Space, 2004 Geophysical Research. Letters.; Pujol et al., 2006 Planetary and Space Science), and we estimate sizes and ablation history of some great fireball and a meteorite fall (Ishihara et al., 2004 Meteoroids2004). In Japan, some great fireball falls occurred during 2004 to 2005. In this presentation, I show the trajectories of these fireballs determined from shockwave analysis. Some fireballs trajectories are also determined from photographic records. The trajectories determined from shockwave and that from photos show good agreement.

Finite element method (FEM) model of the mechanical stress on phospholipid membranes from shock waves produced in nanosecond electric pulses (nsEP)

NASA Astrophysics Data System (ADS)

Barnes, Ronald; Roth, Caleb C.; Shadaram, Mehdi; Beier, Hope; Ibey, Bennett L.

2015-03-01

The underlying mechanism(s) responsible for nanoporation of phospholipid membranes by nanosecond pulsed electric fields (nsEP) remains unknown. The passage of a high electric field through a conductive medium creates two primary contributing factors that may induce poration: the electric field interaction at the membrane and the shockwave produced from electrostriction of a polar submersion medium exposed to an electric field. Previous work has focused on the electric field interaction at the cell membrane, through such models as the transport lattice method. Our objective is to model the shock wave cell membrane interaction induced from the density perturbation formed at the rising edge of a high voltage pulse in a polar liquid resulting in a shock wave propagating away from the electrode toward the cell membrane. Utilizing previous data from cell membrane mechanical parameters, and nsEP generated shockwave parameters, an acoustic shock wave model based on the Helmholtz equation for sound pressure was developed and coupled to a cell membrane model with finite-element modeling in COMSOL. The acoustic structure interaction model was developed to illustrate the harmonic membrane displacements and stresses resulting from shockwave and membrane interaction based on Hooke's law. Poration is predicted by utilizing membrane mechanical breakdown parameters including cortical stress limits and hydrostatic pressure gradients.

Working mechanism of extracorporeal shockwave therapy in non-urological disciplines

NASA Astrophysics Data System (ADS)

Schaden, Wolfgang

2005-04-01

For 32 years of extracorporeal shockwave lithotripsy (ESWL) only the mechanical strength of shockwaves were of clinical interest. For use in orthopaedics, the absence of dangerous long term effects (malignant degeneration, etc.) is the only important message. The mechanical model tries to explain the effect of shock waves by the provocation of microleasions in the tissue stimulating repairing processes. First doubts on this mechanical model came up when Schaden (2001) could show, that less energy is more efficient in the treatment of non-unions. Due to the basic research of the last years knowledge increased about the microbiological effects. Under the influence of shock waves the change of permeability of cell membranes and the liberation of free radicals was reported. Also the production of nitric oxide (NO) and different growth factors like vascular endothelial growth factor (VEGF), bone morphogenetic proteins (BMP), transforming growth factor-beta 1 (TGF-b1), insulin-like growth factor-I (IGF-I) etc. was observed. The biological model tries to explain the effect of shock waves by stimulating the ingrowth of blood vessels and liberation of growth factors. Under the influence of shock waves, biological tissues seem to be able to produce important substances to initiate healing processes.

Extracorporeal shockwave therapy in calcifying tendinitis of the shoulder.

PubMed

Farr, Sebastian; Sevelda, Florian; Mader, Patrick; Graf, Alexandra; Petje, Gert; Sabeti-Aschraf, Manuel

2011-12-01

Strategies for extracorporeal shockwave therapy in calcifying tendinitis of the rotator cuff vary concerning quantity of sessions and doses. The purpose of this prospective pilot study was to determine the difference between the outcome of a single high-dosage extracorporeal shockwave therapy and two sessions of low-dosage extracorporeal shockwave therapy. This study compared a single high-level middle-energetic extracorporeal shockwave therapy (0.3 mJ/mm(2)) with a low-level middle-energetic extracorporeal shockwave therapy applied twice in a weekly interval (0.2 mJ/mm(2)). Thirty patients that suffered from calcifying tendinitis for at least 6 months received navigated, fluoroscopy-guided extracorporeal shockwave therapy. The gain of Constant Murley Score, Visual Analogue Scale during state of rest and weight-bearing situations ("stress") and radiographic progress was documented 6 and 12 weeks after therapy. In both groups, a significant reduction in pain during stress and improvement of function was observed. In contrast, no significant reduction in pain during rest was observed. No significant difference between both groups concerning reduction in the calcific deposit after 6 weeks was detected. Group B showed minor advantages in radiographical improvement after 12 weeks. In 36% of the patients, the calcific deposit completely dissoluted after 12 weeks. This pilot study indicates that a single high-level extracorporeal shockwave therapy may be as effective as two applications of a lower-dosed extracorporeal shockwave therapy for calcifying tendinitis. An effective single-session strategy could reduce treatment time, material costs and healthcare expenses and ionizing radiation in case of fluoroscopy guidance.

Enhanced High-Rate Shockwave Lithotripsy Stone Comminution in an In Vivo Porcine Model Using Acoustic Bubble Coalescence.

PubMed

Alavi Tamaddoni, Hedieh; Roberts, William W; Duryea, Alexander P; Cain, Charles A; Hall, Timothy L

2016-12-01

Cavitation plays a significant role in the efficacy of stone comminution during shockwave lithotripsy (SWL). Although cavitation on the surface of urinary stones helps to improve fragmentation, cavitation bubbles along the propagation path may shield or block subsequent shockwaves (SWs) and potentially induce collateral tissue damage. Previous in vitro work has shown that applying low-amplitude acoustic waves after each SW can force bubbles to consolidate and enhance SWL efficacy. In this study, the feasibility of applying acoustic bubble coalescence (ABC) in vivo was tested. Model stones were percutaneously implanted and treated with 2500 lithotripsy SWs at 120 SW/minute with or without ABC. Comparing the results of stone comminution, a significant improvement was observed in the stone fragmentation process when ABC was used. Without ABC, only 25% of the mass of the stone was fragmented to particles <2 mm in size. With ABC, 75% of the mass was fragmented to particles <2 mm in size. These results suggest that ABC can reduce the shielding effect of residual bubble nuclei, resulting in a more efficient SWL treatment.

Acute brain trauma

PubMed Central

Martin, GT

2016-01-01

In the 20th century, the complications of head injuries were controlled but not eliminated. The wars of the 21st century turned attention to blast, the instant of impact and the primary injury of concussion. Computer calculations have established that in the first 5 milliseconds after the impact, four independent injuries on the brain are inflicted: 1) impact and its shockwave, 2) deceleration, 3) rotation and 4) skull deformity with vibration (or resonance). The recovery, pathology and symptoms after acute brain trauma have always been something of a puzzle. The variability of these four modes of injury, along with a variable reserve of neurones, explains some of this problem. PMID:26688392

Physical insights of cavity confinement enhancing effect in laser-induced breakdown spectroscopy.

PubMed

Fu, Yangting; Hou, Zongyu; Wang, Zhe

2016-02-08

Using cavity confinement to enhance the plasma emission has been proved to be an effective way in LIBS technique while no direct visual evidence has been made to illustrate the physical mechanism of this enhancing effect. In this work, both laser-induced plasma plume images and shockwave images were obtained and synchronized for both flat surface case and rectangular cavity case. Phenomena of shockwave reflection, plasma compression by the reflected shockwave and merge of the reflected shockwave into plasma were observed. Plasma emission intensities recorded by ICCD in both cases were compared and the enhancement effect in the cavity case was identified in the comparison. The enhancement effect could be explained as reflected shockwave "compressing" effect, that is, the reflected shockwave would compress the plasma and result in a more condensed plasma core area with higher plasma temperature. Reflected shockwave also possibly contributed to plasma core position stabilization, which indicated the potential of better plasma signal reproducibility for the cavity case. Both plasma emission enhancement and plasma core position stabilization only exist within a certain temporal window, which indicates that the delay time of spectra acquisition is essential while using cavity confinement as a way to improve LIBS performance.

Shockwave Consolidation of Nanostructured Thermoelectric Materials

NASA Technical Reports Server (NTRS)

Prasad, Narasimha S.; Taylor, Patrick; Nemir, David

2014-01-01

Nanotechnology based thermoelectric materials are considered attractive for developing highly efficient thermoelectric devices. Nano-structured thermoelectric materials are predicted to offer higher ZT over bulk materials by reducing thermal conductivity and increasing electrical conductivity. Consolidation of nano-structured powders into dense materials without losing nanostructure is essential towards practical device development. Using the gas atomization process, amorphous nano-structured powders were produced. Shockwave consolidation is accomplished by surrounding the nanopowder-containing tube with explosives and then detonating. The resulting shock wave causes rapid fusing of the powders without the melt and subsequent grain growth. We have been successful in generating consolidated nano-structured bismuth telluride alloy powders by using the shockwave technique. Using these consolidated materials, several types of thermoelectric power generating devices have been developed. Shockwave consolidation is anticipated to generate large quantities of nanostructred materials expeditiously and cost effectively. In this paper, the technique of shockwave consolidation will be presented followed by Seebeck Coefficient and thermal conductivity measurements of consolidated materials. Preliminary results indicate a substantial increase in electrical conductivity due to shockwave consolidation technique.

Shock-wave flow regimes at entry into the diffuser of a hypersonic ramjet engine: Influence of physical properties of the gas medium

NASA Astrophysics Data System (ADS)

Tarnavskii, G. A.

2006-07-01

The physical aspects of the effective-adiabatic-exponent model making it possible to decompose the total problem on modeling of high-velocity gas flows into individual subproblems (“physicochemical processes” and “ aeromechanics”), which ensures the creation of a universal and efficient computer complex divided into a number of independent units, have been analyzed. Shock-wave structures appearing at entry into the duct of a hypersonic aircraft have been investigated based on this methodology, and the influence of the physical properties of the gas medium in a wide range of variations of the effective adiabatic exponent has been studied.

Shockwave-Induced Plasticity Via Large-Scale Nonequilibrium Molecular Dynamics

NASA Astrophysics Data System (ADS)

Holian, Brad Lee

1997-07-01

In nonequilibrium molecular-dynamics (MD) simulations of shock waves in single crystals, carried out in 1979 at Los Alamos,(B.L. Holian and G.K. Straub, Phys. Rev. Lett. 43), 1598 (1979). we discovered that, above a threshold strength, strongly shocked crystals deform in a very simple way. Rather than experiencing massive deformation, a simple slippage occurs at the shock front, relieving the peak shear stress, and leaving behind a stacking fault. We realized, of course, that real materials could yield at much lower thresholds, and speculated then that pre-existing defects could nucleate plastic flow at lower shock strengths than those characteristic of pure single crystals. (Historical note: at about the same time as our earliest dynamical shockwave simulations, Mogilevsky, working independently in the Soviet Union, carried out relaxation MD calculations under uniaxial strain, and observed spontaneous production of dislocations.(M.A. Mogilevsky, in Shock Waves and High Strain Rate Phenomena in Metals) (Plenum, New York, 1981), p.531.) Further Los Alamos calculations, carried out nearly a decade later in five-times larger systems (up to 10,000 atoms), confirmed this observation and quantified the threshold strength, namely the yield strength of the perfect crystal.(B.L. Holian, Phys. Rev. A 37), 2562 (1988); for a review, see B.L. Holian, Shock Waves 5, 149 (1995). Subsequently, Zaretskii and co-workers,(E.B. Zaretskii, G.I. Kanel, P.A. Mogilevskii, and V.E. Fortov, Sov. Phys. Dokl. 36), 76 (1991). using x-ray diffraction of shocked single crystals, confirmed our MD observations of stacking faults produced by shockwave passage. With the advent of massively parallel computers, we have recently studied systems with over six-times larger cross-sectional area and four-times longer distance of run to the steady state (approximately 270,000 atoms). We have seen that the increased cross-section allows the system to slip along both available forward slip systems, in different places along the now non-planar shock front, though only one stacking fault survives. This leads us to attempt simulations with even larger cross-sectional areas, and with pre-existing defects embedded in the sample, such as those we will report on here (36-times larger cross-sectional area: 10 million atoms). We report on shock waves in fcc copper, where the atoms interact via an EAM (embedded-atom-method) many-body potential, as well as pair-potential materials.(B.L. Holian, P.S. Lomdahl, S.J. Zhou, D.M. Beazley, and A.F. Voter, (1997, unpublished).)

Shockwave dynamics: a comparison between stochastic and periodic porous architectures

NASA Astrophysics Data System (ADS)

Branch, Brittany; Ionite, Axinte; Clements, Bradford; Montgomery, David; Schmalzer, Andrew; Patterson, Brian; Mueller, Alexander; Jensen, Brian; Dattelbaum, Dana

Polymeric foams are used extensively as structural supports and load mitigating materials in which they are subjected to compressive loading at a range of strain rates, up to the high strain rates encountered in blast and shockwave loading. To date, there have been few insights into compaction phenomena in porous structures at the mesoscale, and the influence of structure on shockwave localization. Of particular interest is when the properties of the inherent mesoscopic, periodic structure begin to emerge, versus the discrete behavior of the individual cell. Here, we illustrate, for the first time, modulation of shockwave dynamics controlled at micron-length scales in additively manufactured periodic porous structures measured using in situ, time-resolved x-ray phase contrast imaging at the Advanced Photon Source. Further, we demonstrate how the shockwave dynamics in periodic structures differ from stochastic foams of similar density and we conclude that microstructural control in elastomer foams has a dramatic effect on shockwave dynamics and can be tailored towards a variety of applications. Laboratory Directed Research and Development (LDRD) program at Los Alamos National Laboratory (project# 20160103DR) and DOE/NNSA Campaign 2.

Planetary atmospheres program

NASA Technical Reports Server (NTRS)

1982-01-01

Non-solar compositional models of the troposphere of Jupiter, halide cloud condensation and volatile element inventories on Venus, and shock-wave processing of interstellar cloud materials are discussed.

Extracorporeal shockwave therapy versus exercise program in patients with low back pain: short-term results of a randomised controlled trial.

PubMed

Notarnicola, A; Maccagnano, G; Gallone, M F; Mastromauro, L; Rifino, F; Pesce, V; Covelli, I; Moretti, B

2018-01-01

The physiotherapy treatment of low back pain (LBP) with physical stimulation offers different possibilities of application. Until now, the physical therapies used in LBP are laser therapy, ultrasonotherapy and currents. We conducted a clinical trial in order to verify whether shockwave therapy, which is very effective in treating tendinopathies and fracture consolidation delays, leads to clinical and electromyographic improvement in patients affected by LBP. We randomized thirty patients affected by LBP treated with shock waves (shockwave group) or a standard protocol characterized by rehabilitative exercises (control group). At one and three months, the patients treated with shockwave therapy showed clinical improvement measured by VAS scales (p=0.002; p= 0.02), and disability evaluated with Roland scales (p=0.002; p=0.002) and Oswestry (p=0.002; p=0.002). At three months, the patients treated with shock waves, showed a significant improvement in terms of values of amplitude of the sensory nerve conduction velocity (SNCV) of the plantar medialis nerve (left: p=0.007; right: p=0.04), the motor nerve muscular conduction (MNCV) of the deep peroneal nerve (left: p=0.28; right: p=0.01) and recruitment of motor units of finger brevis extensor (left: p = 0.02; right: p=0.006). In the control group, there was a trend to increase the clinical and electromyographic results without statistical significance. The preliminary results suggest a good applicability of shockwave therapy in the treatment of LBP, in accordance with the antiinflammatory, antalgic, decontracting effects and remodeling of the nerve fiber damage verified in previous studies conducted on other pathological models. Future research will allow us to verify the integration of this therapy into a rehabilitation protocol combined with other physical therapies.

On the finite length-scale of compressible shock-waves formed in free-surface flows of dry granular materials down a slope

NASA Astrophysics Data System (ADS)

Faug, Thierry

2017-04-01

The Rankine-Hugoniot jump conditions traditionally describe the theoretical relationship between the equilibrium state on both sides of a shock-wave. They are based on the crucial assumption that the length-scale needed to adjust the equilibrium state upstream of the shock to downstream of it is too small to be of significance to the problem. They are often used with success to describe the shock-waves in a number of applications found in both fluid and solid mechanics. However, the relations based on jump conditions at singular surfaces may fail to capture some features of the shock-waves formed in complex materials, such as granular matter. This study addresses the particular problem of compressible shock-waves formed in flows of dry granular materials down a slope. This problem is for instance relevant to full-scale geophysical granular flows in interaction with natural obstacles or man-made structures, such as topographical obstacles or mitigation dams respectively. Steady-state jumps formed in granular flows and travelling shock-waves produced at the impact of a granular avalanche-flow with a rigid wall are considered. For both situations, new analytical relations which do not consider that the granular shock-wave shrinks into a singular surface are derived, by using balance equations in their depth-averaged forms for mass and momentum. However, these relations need additional inputs that are closure relations for the size and the shape of the shock-wave, and a relevant constitutive friction law. Small-scale laboratory tests and numerical simulations based on the discrete element method are shortly presented and used to infer crucial information needed for the closure relations. This allows testing some predictive aspects of the simple analytical approach proposed for both steady-state and travelling shock-waves formed in free-surface flows of dry granular materials down a slope.

Effectiveness of Shockwave Treatment Combined With Eccentric Training for Patellar Tendinopathy: A Double-Blinded Randomized Study.

PubMed

Thijs, Karin M; Zwerver, Johannes; Backx, Frank J G; Steeneken, Victor; Rayer, Stephan; Groenenboom, Petra; Moen, Maarten H

2017-03-01

To evaluate the effectiveness of a combined treatment of focused shockwave therapy (ESWT) and eccentric training compared with sham-shockwave therapy (placebo) and eccentric training in participants with patellar tendinopathy (PT) after 24 weeks. Randomized controlled trial. Sports medicine departments of a university hospital and a general hospital in the Netherlands. Fifty-two physically active male and female participants with a clinical diagnosis of PT (mean age: 28.6 years; range, 18-45) were randomly allocated to the ESWT (n = 22) or sham shockwave (n = 30). Extracorporeal shockwave therapy and sham shockwave were applied in 3 sessions at 1-week intervals with a piezoelectric device. All participants were instructed to perform eccentric exercises (3 sets of 15 repetitions twice a day) for 3 months on a decline board at home. The Victorian Institute of Sport Assessment-Patella (VISA-P) scores (primary), pain scores during functional knee loading tests, and Likert score (secondary) were registered at baseline and at 6, 12, and 24 weeks after the start with the ESWT or sham-shockwave treatment. No significant differences for the primary and secondary outcome measures were found between the groups. In the ESWT/eccentric group, the VISA-P increased from 54.5 ± 15.4 to 70.9 ± 17.8, whereas the VISA-P in the sham-shockwave/eccentric group increased from 58.9 ± 14.6 to 78.2 ± 15.8 (between-group change in VISA-P at 24 weeks -4.8; 95% confidence interval, -12.7 to 3.0, P = 0.150). This study showed no additional effect of 3 sessions ESWT in participants with PT treated with eccentric exercises. The results should be interpreted with caution because of small sample size and considerable loss to follow-up, particularly in the ESWT group.

Second shock ejecta measurements with an explosively driven two-shockwave drive

NASA Astrophysics Data System (ADS)

Buttler, W. T.; Oró, D. M.; Olson, R. T.; Cherne, F. J.; Hammerberg, J. E.; Hixson, R. S.; Monfared, S. K.; Pack, C. L.; Rigg, P. A.; Stone, J. B.; Terrones, G.

2014-09-01

We develop and apply an explosively driven two-shockwave tool in material damage experiments on Sn. The two shockwave tool allows the variation of the first shockwave amplitude over range 18.5 to 26.4 GPa, with a time interval variation between the first and second shock of 5 to 7 μs. Simulations imply that the second shock amplitude can be varied as well and we briefly describe how to achieve such a variation. Our interest is to measure ejecta masses from twice shocked metals. In our application of the two-shockwave tool, we observed second shock ejected areal masses of about 4 ± 1 mg/cm2, a value we attribute to unstable Richtmyer-Meshkov impulse phenomena. We also observed an additional mass ejection process caused by the abrupt recompression of the local spallation or cavitation of the twice shocked Sn.

Development and Preclinical Testing of Laser-Generated Shockwave Therapy for Infected Wounds

NASA Astrophysics Data System (ADS)

Francis, Nathan Craig

The goal of this thesis is to translate laser-generated shockwave (LGS) therapy from a bench-top, research system into a portable, clinical system for in vivo animal trials. Prior research along this topic was completed using a benchtop system, in a physical setup dissimilar to the clinical setup. So the technology required re-engineering in order to apply it to animal studies. This began with the construction of a portable LGS therapy system, mobile enough to transport from laboratory to clinical settings. Included in the portable system is a 2D scanning system to consistently treat wound areas of varying geometries with shockwaves of 3 mm diameter spot sizes. The shockwaves generated by the portable laser system were characterized, along with the varying shockwave-generating substrates possible for clinical application. A final material selection of black polyimide was chosen because of its complete absorption of laser light and its ability to conform to tight wound geometries. Since shockwaves have never been demonstrated to delaminate biofilm from a tissue surface, a proof-of-concept study was completed successfully delaminating Staphylococcus epidermidis from wounded ex vivo pigskin. Through false-colored SEM imaging, biofilm area reduction between treated and non-treated samples were calculated. A 53% reduction in biofilm area and signifcant biofilm fragmentation was seen. An in vivo safety study was conducted next to observe potential physiological effects of LGS on healthy dermal tissue. Treated subjects were observed over a 3 day period, and no physiological or inflammatory effects were seen in the histological analysis. Finally, a pilot wound healing study was com- pleted on excisional wound healing model in rats, with S. epidermidis as the infectious agent, to measure the effect of LGS on wound healing area and rate compared to other treatments. After 9 days of wound healing, no treatment or controls showed a significant difference in wound healing rate or wound area. As a result, LGS also showed no deleterious effects on the tissue which would hinder wound healing. With these results, LGS therapy shows promise as an alternative infected wound treatment, and a system capable of completing thorough animal trials is available for future researchers.

Stepwise shockwave velocity determinator

NASA Technical Reports Server (NTRS)

Roth, Timothy E.; Beeson, Harold

1992-01-01

To provide an uncomplicated and inexpensive method for measuring the far-field velocity of a surface shockwave produced by an explosion, a stepwise shockwave velocity determinator (SSVD) was developed. The velocity determinator is constructed of readily available materials and works on the principle of breaking discrete sensors composed of aluminum foil contacts. The discrete sensors have an average breaking threshold of approximately 7 kPa. An incremental output step of 250 mV is created with each foil contact breakage and is logged by analog-to-digital instrumentation. Velocity data obtained from the SSVD is within approximately 11 percent of the calculated surface shockwave velocity of a muzzle blast from a 30.06 rifle.

High-speed imaging optical techniques for shockwave and droplets atomization analysis

NASA Astrophysics Data System (ADS)

Slangen, Pierre R.; Lauret, Pierre; Heymes, Frederic; Aprin, Laurent; Lecysyn, Nicolas

2016-12-01

Droplets atomization by shockwave can act as a consequence in domino effects on an industrial facility: aggression of a storage tank (projectile from previous event, for example) can cause leakage of hazardous material (toxic and flammable). As the accident goes on, a secondary event can cause blast generation, impacting the droplets and resulting in their atomization. Therefore, exchange surface increase impacts the evaporation rate. This can be an issue in case of dispersion of such a cloud. The experiments conducted in the lab generate a shockwave with an open-ended shock tube to break up liquid droplets. As the expected shockwave speed is about 400 m/s (˜Mach 1.2), the interaction with falling drops is very short. High-speed imaging is performed at about 20,000 fps. The shockwave is measured using both overpressure sensors: particle image velocimetry and pure in line shadowgraphy. The size of fragmented droplets is optically measured by direct shadowgraphy simultaneously in different directions. In these experiments, secondary breakups of a droplet into an important number of smaller droplets from the shockwave-induced flow are shown. The results of the optical characterizations are discussed in terms of shape, velocity, and size.

Extended asymmetric hot region formation due to shockwave interactions following void collapse in shocked high explosive

NASA Astrophysics Data System (ADS)

Shan, Tzu-Ray; Wixom, Ryan R.; Thompson, Aidan P.

2016-08-01

In both continuum hydrodynamics simulations and also multimillion atom reactive molecular dynamics simulations of shockwave propagation in single crystal pentaerythritol tetranitrate (PETN) containing a cylindrical void, we observed the formation of an initial radially symmetric hot spot. By extending the simulation time to the nanosecond scale, however, we observed the transformation of the small symmetric hot spot into a longitudinally asymmetric hot region extending over a much larger volume. Performing reactive molecular dynamics shock simulations using the reactive force field (ReaxFF) as implemented in the LAMMPS molecular dynamics package, we showed that the longitudinally asymmetric hot region was formed by coalescence of the primary radially symmetric hot spot with a secondary triangular hot zone. We showed that the triangular hot zone coincided with a double-shocked region where the primary planar shockwave was overtaken by a secondary cylindrical shockwave. The secondary cylindrical shockwave originated in void collapse after the primary planar shockwave had passed over the void. A similar phenomenon was observed in continuum hydrodynamics shock simulations using the CTH hydrodynamics package. The formation and growth of extended asymmetric hot regions on nanosecond timescales has important implications for shock initiation thresholds in energetic materials.

Suppression of shocked-bubble expansion due to tissue confinement with application to shock-wave lithotripsy

PubMed Central

Freund, Jonathan B.

2008-01-01

Estimates are made of the effect of tissue confinement on the response of small bubbles subjected to lithotriptor shock pressures. To do this the Rayleigh–Plesset equation, which governs the dynamics of spherical bubbles, is generalized to treat a bubble in a liquid region (blood), which is in turn encased within an elastic membrane (like a vessel’s basement membrane), beyond which a Voigt viscoelastic material models the exterior tissue. Material properties are estimated from a range of measurements available for kidneys and similar soft tissues. Special attention is given to the constitutive modeling of the basement membranes because of their expected importance due to their proximity to the bubble and their toughness. It is found that the highest expected values for the elasticity of the membrane and surrounding tissue are insufficient to suppress bubble growth. The reduced confinement of a cylindrical vessel should not alter this conclusion. Tissue viscosities taken from ultrasound measurements suppress bubble growth somewhat, though not to a degree expected to resist injury. However, the higher reported viscosities measured by other means, which are arguably more relevant to the deformations caused by growing bubbles, do indeed significantly suppress bubble expansion. PMID:18529202

Suppression of shocked-bubble expansion due to tissue confinement with application to shock-wave lithotripsy.

PubMed

Freund, Jonathan B

2008-05-01

Estimates are made of the effect of tissue confinement on the response of small bubbles subjected to lithotriptor shock pressures. To do this the Rayleigh-Plesset equation, which governs the dynamics of spherical bubbles, is generalized to treat a bubble in a liquid region (blood), which is in turn encased within an elastic membrane (like a vessel's basement membrane), beyond which a Voigt viscoelastic material models the exterior tissue. Material properties are estimated from a range of measurements available for kidneys and similar soft tissues. Special attention is given to the constitutive modeling of the basement membranes because of their expected importance due to their proximity to the bubble and their toughness. It is found that the highest expected values for the elasticity of the membrane and surrounding tissue are insufficient to suppress bubble growth. The reduced confinement of a cylindrical vessel should not alter this conclusion. Tissue viscosities taken from ultrasound measurements suppress bubble growth somewhat, though not to a degree expected to resist injury. However, the higher reported viscosities measured by other means, which are arguably more relevant to the deformations caused by growing bubbles, do indeed significantly suppress bubble expansion.

Extended asymmetric hot region formation due to shockwave interactions following void collapse in shocked high explosive

DOE PAGES

Shan, Tzu -Ray; Wixom, Ryan R.; Thompson, Aidan P.

2016-08-01

In both continuum hydrodynamics simulations and also multimillion atom reactive molecular dynamics simulations of shockwave propagation in single crystal pentaerythritol tetranitrate (PETN) containing a cylindrical void, we observed the formation of an initial radially symmetric hot spot. By extending the simulation time to the nanosecond scale, however, we observed the transformation of the small symmetric hot spot into a longitudinally asymmetric hot region extending over a much larger volume. Performing reactive molecular dynamics shock simulations using the reactive force field (ReaxFF) as implemented in the LAMMPS molecular dynamics package, we showed that the longitudinally asymmetric hot region was formed bymore » coalescence of the primary radially symmetric hot spot with a secondary triangular hot zone. We showed that the triangular hot zone coincided with a double-shocked region where the primary planar shockwave was overtaken by a secondary cylindrical shockwave. The secondary cylindrical shockwave originated in void collapse after the primary planar shockwave had passed over the void. A similar phenomenon was observed in continuum hydrodynamics shock simulations using the CTH hydrodynamics package. Furthermore, the formation and growth of extended asymmetric hot regions on nanosecond timescales has important implications for shock initiation thresholds in energetic materials.« less

Extended asymmetric hot region formation due to shockwave interactions following void collapse in shocked high explosive

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shan, Tzu -Ray; Wixom, Ryan R.; Thompson, Aidan P.

In both continuum hydrodynamics simulations and also multimillion atom reactive molecular dynamics simulations of shockwave propagation in single crystal pentaerythritol tetranitrate (PETN) containing a cylindrical void, we observed the formation of an initial radially symmetric hot spot. By extending the simulation time to the nanosecond scale, however, we observed the transformation of the small symmetric hot spot into a longitudinally asymmetric hot region extending over a much larger volume. Performing reactive molecular dynamics shock simulations using the reactive force field (ReaxFF) as implemented in the LAMMPS molecular dynamics package, we showed that the longitudinally asymmetric hot region was formed bymore » coalescence of the primary radially symmetric hot spot with a secondary triangular hot zone. We showed that the triangular hot zone coincided with a double-shocked region where the primary planar shockwave was overtaken by a secondary cylindrical shockwave. The secondary cylindrical shockwave originated in void collapse after the primary planar shockwave had passed over the void. A similar phenomenon was observed in continuum hydrodynamics shock simulations using the CTH hydrodynamics package. Furthermore, the formation and growth of extended asymmetric hot regions on nanosecond timescales has important implications for shock initiation thresholds in energetic materials.« less

Burnett-Cattaneo continuum theory for shock waves.

PubMed

Holian, Brad Lee; Mareschal, Michel; Ravelo, Ramon

2011-02-01

We model strong shock-wave propagation, both in the ideal gas and in the dense Lennard-Jones fluid, using a refinement of earlier work, which accounts for the cold compression in the early stages of the shock rise by a nonlinear, Burnett-like, strain-rate dependence of the thermal conductivity, and relaxation of kinetic-temperature components on the hot, compressed side of the shock front. The relaxation of the disequilibrium among the three components of the kinetic temperature, namely, the difference between the component in the direction of a planar shock wave and those in the transverse directions, particularly in the region near the shock front, is accomplished at a much more quantitative level by a rigorous application of the Cattaneo-Maxwell relaxation equation to a reference solution, namely, the steady shock-wave solution of linear Navier-Stokes-Fourier theory, along with the nonlinear Burnett heat-flux term. Our new continuum theory is in nearly quantitative agreement with nonequilibrium molecular-dynamics simulations under strong shock-wave conditions, using relaxation parameters obtained from the reference solution. ©2011 American Physical Society

Aerodynamic Design and Numerical Analysis of Supersonic Turbine for Turbo Pump

NASA Astrophysics Data System (ADS)

Fu, Chao; Zou, Zhengping; Kong, Qingguo; Cheng, Honggui; Zhang, Weihao

2016-09-01

Supersonic turbine is widely used in the turbo pump of modern rocket. A preliminary design method for supersonic turbine has been developed considering the coupling effects of turbine and nozzle. Numerical simulation has been proceeded to validate the feasibility of the design method. As the strong shockwave reflected on the mixing plane, additional numerical simulated error would be produced by the mixing plane model in the steady CFD. So unsteady CFD is employed to investigate the aerodynamic performance of the turbine and flow field in passage. Results showed that the preliminary design method developed in this paper is suitable for designing supersonic turbine. This periodical variation of complex shockwave system influences the development of secondary flow, wake and shock-boundary layer interaction, which obviously affect the secondary loss in vane passage. The periodical variation also influences the strength of reflecting shockwave, which affects the profile loss in vane passage. Besides, high circumferential velocity at vane outlet and short blade lead to high radial pressure gradient, which makes the low kinetic energy fluid moves towards hub region and produces additional loss.

Estimating model parameters for an impact-produced shock-wave simulation: Optimal use of partial data with the extended Kalman filter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kao, Jim; Flicker, Dawn; Ide, Kayo

2006-05-20

This paper builds upon our recent data assimilation work with the extended Kalman filter (EKF) method [J. Kao, D. Flicker, R. Henninger, S. Frey, M. Ghil, K. Ide, Data assimilation with an extended Kalman filter for an impact-produced shock-wave study, J. Comp. Phys. 196 (2004) 705-723.]. The purpose is to test the capability of EKF in optimizing a model's physical parameters. The problem is to simulate the evolution of a shock produced through a high-speed flyer plate. In the earlier work, we have showed that the EKF allows one to estimate the evolving state of the shock wave from amore » single pressure measurement, assuming that all model parameters are known. In the present paper, we show that imperfectly known model parameters can also be estimated accordingly, along with the evolving model state, from the same single measurement. The model parameter optimization using the EKF can be achieved through a simple modification of the original EKF formalism by including the model parameters into an augmented state variable vector. While the regular state variables are governed by both deterministic and stochastic forcing mechanisms, the parameters are only subject to the latter. The optimally estimated model parameters are thus obtained through a unified assimilation operation. We show that improving the accuracy of the model parameters also improves the state estimate. The time variation of the optimized model parameters results from blending the data and the corresponding values generated from the model and lies within a small range, of less than 2%, from the parameter values of the original model. The solution computed with the optimized parameters performs considerably better and has a smaller total variance than its counterpart using the original time-constant parameters. These results indicate that the model parameters play a dominant role in the performance of the shock-wave hydrodynamic code at hand.« less

Quasi-thermal models

NASA Technical Reports Server (NTRS)

Delareza, Ramiro

1987-01-01

Non-local thermodynamics equilibrium (LTE) effects in the photosphere; recent research on the chromosphere of the M and C stars; and elementary shock-waves and pulsation theories and their applications to Mira long-period variables are discussed.

Shockwave Interaction with a Cylindrical Structure

NASA Astrophysics Data System (ADS)

Mulligan, Phillip

2017-06-01

An increased understanding of the shockwave interaction with a cylindrical structure is the foundation for developing a method to explosively seal a pipe similar to the Deepwater Horizon accident in the Gulf of Mexico. Shockwave interactions with a cylindrical structure have been a reoccurring focus of energetics research. Some of the most notable contributions of non-destructive tests are described in ``The Effects of Nuclear Weapons'' (Glasstone, 1962). The work presented by Glasstone examines shockwave interaction from a 20-megaton bomb with a cylindrical structure. However, the data is limited to a peak overpressure of less than 25 psi, requiring several miles between the structure and the charge. The research presented in the following paper expands on the work Glasstone described by examining the shockwaves from 90, 180, and 270-gram C-4 charges interacting with a 6-inch diameter cylindrical structure positioned 52-inches from the center of the charge. The three charge weights that were tested in this research generated a peak overpressures of approximately 15, 25, and 40 psi, respectively. This research examines the peak pressure and total impulse from each charge acting on the cylindrical structure as well as the formation of vortices on the ``backside'' of the cylinder surface. This paper describes the methodology and findings of this study as well as examines the causality and implications of its results on our understanding of the shockwave interaction with a cylindrical structure.

Shockwave-Loading-Induced Enhancement of T c in Superconducting Bi 2Sr 2CaCu 2O 8+δ

DOE PAGES

Liu, Tiansheng; He, Chao; Wang, Fengying; ...

2017-07-27

Here, we report a shockwave method for altering the properties of the superconductor material Bi 2Sr 2CaCu 2O 8+δ (Bi2212). We find that the superconducting transition temperature (T c) increases from 84 K for the pristine sample to 94 K for the sample treated at a temperature and pressure of ~1200 K and ~31 GPa, respectively. X-ray diffraction and transmission electron microscopy characterizations indicate that this T c enhancement arises from a phase transition from pristine Bi2212 to a mixture of superconducting Bi2212 and semiconducting Bi 2Sr 2CuO 6+δ (Bi2201) during the shockwave treatment. The shockwave-treated sample exhibits n-type semiconductormore » properties (with an on-off ratio ~5), in contrast to the pure metallic pristine sample. This study offers an alternative route for modifying the superconducting properties via a shockwave treatment. Furthermore, this method may provide a new approach for studying other temperature- and pressure-sensitive materials.« less

One-year treatment follow-up of plantar fasciitis: radial shockwaves vs. conventional physiotherapy

PubMed Central

Grecco, Marcus Vinicius; Brech, Guilherme Carlos; Greve, Júlia Maria D'Andrea

2013-01-01

OBJECTIVE: To compare radial shockwave treatment with conventional physiotherapy for plantar fasciitis after 12 months of follow-up. METHOD: This was a randomized, prospective, comparative clinical study. Forty patients with a diagnosis of plantar fasciitis were divided randomly into two treatment groups: group 1, with 20 patients who underwent ten physiotherapy sessions comprising ultrasound, kinesiotherapy and guidance for home-based stretching; and group 2, with 20 patients who underwent three applications of radial shockwaves, once a week, and guidance for home-based stretching. All patients were assessed regarding pain and functional abilities before treatment, immediately after and 12 months after treatment. The mean age was 49.6±11.8 years (range: 25-68 years), 85% were female, 88% were overweight, 63% were affected bilaterally, and 83% used analgesics regularly. RESULTS: At the 12-month follow-up, both treatments were effective for improving pain and functional ability among the patients with plantar fasciitis. The improvement with shockwaves was faster. CONCLUSION: Shockwave treatment was not more effective than conventional physiotherapy treatment 12 months after the end of the treatment. PMID:24037003

Comparison of Radial Shockwaves and Conventional Physiotherapy for Treating Plantar Fasciitis

PubMed Central

Greve, Júlia Maria D’Andréa; Grecco, Marcus Vinicius; Santos-Silva, Paulo Roberto

2009-01-01

OBJECTIVE: To compare radial shockwave treatment and conventional physiotherapy for plantar fasciitis. MATERIALS AND METHODS: Thirty-two patients with plantar fasciitis were included in this study. They were randomly divided into two groups. Group 1 was composed of 16 patients who underwent 10 physiotherapy sessions each, consisting of ultrasound, kinesiotherapy and instruction for stretching exercises at home. Group 2 was composed of 16 patients who underwent three applications of radial shockwaves (once a week) and received instruction for stretching exercises at home. Pain and ability to function were evaluated before treatment, immediately afterwards, and three months later. The mean age of the patients was 47.3 ± 10.3 years (range 25–68); 81% were female, 87% were overweight, 56% had bilateral impairment, and 75% used analgesics regularly. RESULTS: Both treatments were effective for pain reduction and for improving the functional abilities of patients with plantar fasciitis. The effect of the shockwaves was apparent sooner than physiotherapy after the onset of treatment. CONCLUSION: Shockwave treatment was no more effective than conventional physiotherapy treatment when evaluated three months after the end of treatment. PMID:19219314

Tissue reactions under piezoelectric shockwave application for the fragmentation of biliary calculi.

PubMed Central

Ell, C; Kerzel, W; Heyder, N; Rödl, W; Langer, H; Mischke, U; Giedl, J; Domschke, W

1989-01-01

The tissue reactions that occurred during piezoelectric shockwaves for the fragmentation of biliary calculi were investigated in 10 surgically removed stone containing human gall bladders and in acute (six dogs) and chronic (six dogs) animal experiments. Before and after shockwave (500, 1500 or 3000) in the anaesthetised dogs, computed tomography (CT), magnetic imaging (MRI) and laboratory tests were done; treatment was carried out under continuous ultrasonographic control. Shockwave applications to the human gall bladders resulted in disintegration of the stones with no macroscopically or microscopically detectable tissue changes. In acute animal experiments, small haematomas were observed in all six animals at surfaces, but also inside the liver and gall bladder (max diameter 25 mm). Perforation or intra-abdominal or pleural bleeding did not occur. In chronic experiments, no macroscopic, and only slight microscopic residual lesions (haemosiderin deposits) were seen three weeks after shockwave. In almost all instances, the lesions were detected by CT, MRI, and ultrasonography, while laboratory tests were negative. Images Fig 1 Figs. 2-4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 PMID:2731762

DSMC study of oxygen shockwaves based on high-fidelity vibrational relaxation and dissociation models

NASA Astrophysics Data System (ADS)

Borges Sebastião, Israel; Kulakhmetov, Marat; Alexeenko, Alina

2017-01-01

This work evaluates high-fidelity vibrational-translational (VT) energy relaxation and dissociation models for pure O2 normal shockwave simulations with the direct simulation Monte Carlo (DSMC) method. The O2-O collisions are described using ab initio state-specific relaxation and dissociation models. The Macheret-Fridman (MF) dissociation model is adapted to the DSMC framework by modifying the standard implementation of the total collision energy (TCE) model. The O2-O2 dissociation is modeled with this TCE+MF approach, which is calibrated with O2-O ab initio data and experimental equilibrium dissociation rates. The O2-O2 vibrational relaxation is modeled via the Larsen-Borgnakke model, calibrated to experimental VT rates. All the present results are compared to experimental data and previous calculations available in the literature. It is found that, in general, the ab initio dissociation model is better than the TCE model at matching the shock experiments. Therefore, when available, efficient ab initio models are preferred over phenomenological models. We also show that the proposed TCE + MF formulation can be used to improve the standard TCE model results when ab initio data are not available or limited.

The effects of shockwave profile shape and shock obliquity on spallation in Cu and Ta: kinetic and stress-state effects on damage evolution(u)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gray, George T

2010-12-14

Widespread research over the past five decades has provided a wealth of experimental data and insight concerning shock hardening and the spallation response of materials subjected to square-topped shock-wave loading profiles. Less quantitative data have been gathered on the effect of direct, in-contact, high explosive (HE)-driven Taylor wave (or triangular-wave) loading profile shock loading on the shock hardening, damage evolution, or spallation response of materials. Explosive loading induces an impulse dubbed a 'Taylor Wave'. This is a significantly different loading history than that achieved by a square-topped impulse in terms of both the pulse duration at a fixed peak pressure,more » and a different unloading strain rate from the peak Hugoniot state achieved. The goal of this research is to quantify the influence of shockwave obliquity on the spallation response of copper and tantalum by subjecting plates of each material to HE-driven sweeping detonation-wave loading and quantify both the wave propagation and the post-mortem damage evolution. This talk will summarize our current understanding of damage evolution during sweeping detonation-wave spallation loading in Cu and Ta and show comparisons to modeling simulations. The spallation responses of Cu and Ta are both shown to be critically dependent on the shockwave profile and the stress-state of the shock. Based on variations in the specifics of the shock drive (pulse shape, peak stress, shock obliquity) and sample geometry in Cu and Ta, 'spall strength' varies by over a factor of two and the details of the mechanisms of the damage evolution is seen to vary. Simplistic models of spallation, such as P{sub min} based on 1-D square-top shock data lack the physics to capture the influence of kinetics on damage evolution such as that operative during sweeping detonation loading. Such considerations are important for the development of predictive models of damage evolution and spallation in metals and alloys.« less

Atomistic material behavior at extreme pressures

DOE PAGES

Beland, Laurent K.; Osetskiy, Yury N.; Stoller, Roger E.

2016-08-05

Computer simulations are routinely performed to model the response of materials to extreme environments, such as neutron (or ion) irradiation. The latter involves high-energy collisions from which a recoiling atom creates a so-called atomic displacement cascade. These cascades involve coordinated motion of atoms in the form of supersonic shockwaves. These shockwaves are characterized by local atomic pressures >15 GPa and interatomic distances <2 Å. Similar pressures and interatomic distances are observed in other extreme environment, including short-pulse laser ablation, high-impact ballistic collisions and diamond anvil cells. Displacement cascade simulations using four different force fields, with initial kinetic energies ranging frommore » 1 to 40 keV, show that there is a direct relationship between these high-pressure states and stable defect production. An important shortcoming in the modeling of interatomic interactions at these short distances, which in turn determines final defect production, is brought to light.« less

Heat-flow equation motivated by the ideal-gas shock wave.

PubMed

Holian, Brad Lee; Mareschal, Michel

2010-08-01

We present an equation for the heat-flux vector that goes beyond Fourier's Law of heat conduction, in order to model shockwave propagation in gases. Our approach is motivated by the observation of a disequilibrium among the three components of temperature, namely, the difference between the temperature component in the direction of a planar shock wave, versus those in the transverse directions. This difference is most prominent near the shock front. We test our heat-flow equation for the case of strong shock waves in the ideal gas, which has been studied in the past and compared to Navier-Stokes solutions. The new heat-flow treatment improves the agreement with nonequilibrium molecular-dynamics simulations of hard spheres under strong shockwave conditions.

Superconductivity of Cu/CuOx interface formed by shock-wave pressure

NASA Astrophysics Data System (ADS)

Shakhray, D. V.; Avdonin, V. V.; Palnichenko, A. V.

2016-11-01

A mixture of powdered Cu and CuO has been subjected to shock-wave pressure of 350 kbar with following quenching of the vacuum-encapsulated product to 77 K. The ac magnetic susceptibility measurements of the samples have revealed metastable superconductivity with Tc ≈ 19 K, characterized by glassy dynamics of the shielding currents below Tc . Comparison of the ac susceptibility and the DC magnetization measurements infers that the superconductivity arises within the granular interfacial layer formed between metallic Cu and its oxides due to the shock-wave treatment.

The effects of extracorporeal shockwave on acute high-energy long bone fractures of the lower extremity.

PubMed

Wang, Ching-Jen; Liu, Hao-Chen; Fu, Te-Hu

2007-02-01

High-energy long bone fractures of the lower extremity are at risk of poor fracture healing and high rate of non-union. Extracorporeal shockwave was shown effective to heal non-union of long bone fracture. However, the effect of shockwave on acute fractures is unknown. The purpose of this study was to investigate the effects of shockwave on acute high-energy fractures of the lower extremity. Between January and October 2004, 56 patients with 59 acute high-energy fractures were enrolled in this study. Patients were randomly divided into two groups with 28 patients with 28 fractures in the study group and 28 patients with 31 fractures in the control group. Both groups showed similar age, gender, type of fracture and follow-up time. Patients in the study group received open reduction and internal fixation and shockwave treatment immediately after surgery on odd-numbered days of the week, whereas, patients in the control group received open reduction and internal fixation without shockwave treatment on even-numbered days of the week. Postoperative managements were similarly performed in both groups including crutch walking with non-weight bearing on the affected limb until fracture healing shown on radiographs. The evaluation parameters included clinical assessments of pain score and weight bearing status of the affected leg and serial radiographs at 3, 6 and 12 months. The primary end-point is the rate of non-union at 12 months, and the secondary end point is the rate of fracture healing at 3, 6 and 12 months. At 12 months, the rate of non-union was 11% for the study group versus 20% for the control group (P < 0.001). Significantly, better rate of fracture healing was noted in the study group than the control group at 3, 6 and 12 months (P < 0.001). Extracorporeal shockwave is effective on promoting fracture healing and decreasing the rate of non-union in acute high-energy fractures of the lower extremity.

Local shock-wave lithotripsy of distal ureteral calculi.

PubMed

Voges, G E; Wilbert, D M; Stöckle, M; Hohenfellner, R

1988-01-01

Since the initiation of the clinical trial utilizing a second-generation lithotripor (Lithostar, Siemens, Erlangen, FRG), 96 patients with distal ureteral calculi (i.e. calculi below the pelvic brim) underwent local shock-wave lithotripsy. Routine treatment was conducted under intravenous sedation and light analgesia only. Complete stone disintegration was achieved in 84 patients (87.5%), 11 requiring two sessions and 1 patient, three. In 7 patients ureteroscopy became necessary after unsuccessful local shock-wave treatment. In 2 of these patients a 9-french flexible ureteroscope and the Storz Q-switched neodymium-YAG laser was used for stone disintegration. In 3 cases loop extraction and in 2 cases open surgery had to be performed for definitive stone removal. All pre- and postoperative manipulations (except open surgery) were done on the Lithostar. Local shock-wave lithotripsy is a highly successful, noninvasive, time-saving and easily applicable technique. It has become our primary approach in the treatment of distal ureteral calculi.

Underwater Shockwave Pretreatment Process to Improve the Scent of Extracted Citrus junos Tanaka (Yuzu) Juice

PubMed Central

Touyama, Akiko; Nakada, Shina; Higa, Osamu; Itoh, Shigeru

2017-01-01

Citrus junos Tanaka (yuzu) has a strong characteristic aroma and thus its juice is used in various Japanese foods. Herein, we evaluate the volatile compounds in yuzu juice to investigate whether underwater shockwave pretreatment affects its scent. A shockwave pretreatment at increased discharge and energy of 3.5 kV and 4.9 kJ, respectively, increased the content of aroma-active compounds. Moreover, the underwater shockwave pretreatment afforded an approximate tenfold increase in the scent intensity of yuzu juice cultivated in Rikuzentakata. The proposed treatment method exhibited reliable and good performance for the extraction of volatile and aroma-active compounds from the yuzu fruit. The broad applicability and high reliability of this technique for improving the scent of yuzu fruit juice were demonstrated, confirming its potential for application to a wide range of food extraction processes. PMID:28761874

Dynamics in a one-dimensional ferrogel model: relaxation, pairing, shock-wave propagation.

PubMed

Goh, Segun; Menzel, Andreas M; Löwen, Hartmut

2018-05-23

Ferrogels are smart soft materials, consisting of a polymeric network and embedded magnetic particles. Novel phenomena, such as the variation of the overall mechanical properties by external magnetic fields, emerge consequently. However, the dynamic behavior of ferrogels remains largely unveiled. In this paper, we consider a one-dimensional chain consisting of magnetic dipoles and elastic springs between them as a simple model for ferrogels. The model is evaluated by corresponding simulations. To probe the dynamics theoretically, we investigate a continuum limit of the energy governing the system and the corresponding equation of motion. We provide general classification scenarios for the dynamics, elucidating the touching/detachment dynamics of the magnetic particles along the chain. In particular, it is verified in certain cases that the long-time relaxation corresponds to solutions of shock-wave propagation, while formations of particle pairs underlie the initial stage of the dynamics. We expect that these results will provide insight into the understanding of the dynamics of more realistic models with randomness in parameters and time-dependent magnetic fields.

[Treatment of kidney stones using shock-wave lithotripsy with sonographic control].

PubMed

Benes, J; Chmel, J; Simon, V; Stuka, C; Flejsar, P

1991-10-01

Lithotripsy by means of an extracorporeal shock-wave was performed in 128 patients with urolithiasis. In this group for the first time in Czechoslovakia ultrasound control of kidney stones was used in 44 patients; in the remainder X-ray control was used. The authors used equipment designed and manufactured locally. The ultrasonic probe is laterally connected with the shock-wave applicator. Disappearance of the fragments after lithotripsy was achieved in 39 patients where ultrasonic control was used. The paper presents the results, discusses the advantages and limitations of ultrasonic control in extracorporeal lithotripsy of urolithiasis.

[Treatment of kidney calculi using shock-wave lithotripsy with ultrasonic guidance].

PubMed

Benes, J; Chmel, J; Simon, V; Stuka, C; Flejsar, P

1991-01-01

Lithotripsy by means of an extracorporeal shock-wave was performed in 128 patients with urolithiasis. In this group for the first time in Czechoslovakia ultrasound control of kidney stones was used in 44 patients; in the remainder X-ray control was used. The authors used equipment designed and manufactured locally. The ultrasonic probe is laterally connected with the shock-wave applicator. Disappearance of the fragments after lithotripsy was achieved in 39 patients where ultrasonic control was used. The paper presents the results, discusses the advantages and limitations of ultrasonic control in extracorporeal lithotripsy of urolithiasis.

[Renal hematomas after extracorporeal shock-wave lithotripsy (ESWL)].

PubMed

Pastor Navarro, Héctor; Carrión López, Pedro; Martínez Ruiz, Jesús; Pastor Guzmán, José Ma; Martínez Martín, Mariano; Virseda Rodríguez, Julio A

2009-03-01

The use of fragmentation due to shock- waves as a treatment of urinary stone was one of the most important therapeutics findings in the history of urology. It's the first election treatment for most of the calculus at renal and urethral location due to the fact that it is a low invasive treatment and it has a few number of complications, but this method also has a few negative side effects, it can caused a more or less important traumatic lesion at the organs which crosses the shock-waves, including the kidney where it can caused a small contusion or renal hematoma with different resolution and treatment. We reviewed 4815 extracorporeal shock-wave lithotripsy that we performed in our department in which we found six cases with subcapsular and perirenal hematoma which we followed up and treated. After the urological complications (pain, obstruction and infection) the renal and perirenal hematic collections are the most frequent adverse effects of shock-waves used in lithotripsy, these are related to the power of energy used and patient age. Between the years 1992-2007 we performed 4.815 extracorporeal shock-wave lithotripsy finding seven cases of severe hematoma, less then 1%. Treatment of these complications is usually not aggressive though sometimes it is necessary to perform surgical drainage and even nephrectomy.

Investigation of structural-scale levels of spall fracture induced by a nanosecond relativistic high-current electron beam in ultrafine-grained Ti-Al-V-Mo alloy

NASA Astrophysics Data System (ADS)

Dudarev, E. F.; Markov, A. B.; Bakach, G. P.; Maletkina, T. Yu.; Belov, N. N.; Tabachenko, A. N.; Skosirskii, A. B.; Habibullin, M. V.; Yakovlev, E. V.

2017-12-01

The results of an experimental and theoretical study of shock-wave processes and spall fracture in an ultrafine-grained and coarse-grained (α + β) Ti-Al-V-Mo alloy under the action of a nanosecond relativistic high-current electron beam are reported. Mathematical modeling is performed to show that when an electron beam with a power density of 1.65 × 1010 W/cm2 impacts this alloy, a shock wave with a compression amplitude of 13 GPa appears and its reflection gives rise to a tensile wave. Its amplitude increases with decreasing target thickness. The calculated increase in the thickness of the spalled layer at the rear surface of the target corresponds to the experimental data. It is established experimentally that plastic deformation precedes the spall fracture sequentially at three structural-scale levels. At the beginning pores are formed and merge, then microcracks are formed at different angles to the back surface of the target between the pores, and then a macrocrack is formed. As a result, the macrocrack surface is not smooth but exhibits pits of ductile fracture.

Comparison of geometrical shock dynamics and kinematic models for shock-wave propagation

NASA Astrophysics Data System (ADS)

Ridoux, J.; Lardjane, N.; Monasse, L.; Coulouvrat, F.

2018-03-01

Geometrical shock dynamics (GSD) is a simplified model for nonlinear shock-wave propagation, based on the decomposition of the shock front into elementary ray tubes. Assuming small changes in the ray tube area, and neglecting the effect of the post-shock flow, a simple relation linking the local curvature and velocity of the front, known as the A{-}M rule, is obtained. More recently, a new simplified model, referred to as the kinematic model, was proposed. This model is obtained by combining the three-dimensional Euler equations and the Rankine-Hugoniot relations at the front, which leads to an equation for the normal variation of the shock Mach number at the wave front. In the same way as GSD, the kinematic model is closed by neglecting the post-shock flow effects. Although each model's approach is different, we prove their structural equivalence: the kinematic model can be rewritten under the form of GSD with a specific A{-}M relation. Both models are then compared through a wide variety of examples including experimental data or Eulerian simulation results when available. Attention is drawn to the simple cases of compression ramps and diffraction over convex corners. The analysis is completed by the more complex cases of the diffraction over a cylinder, a sphere, a mound, and a trough.

Shock-wave facility at Tokyo Institute of Technology

NASA Astrophysics Data System (ADS)

Sawaoka, A.; Kondo, K.

1982-04-01

The shock-wave facility at the Tokyo Institute of Technology is described. Two double-stage light-gas guns are used to studying material science and technology. Recently construction has begun for a new type of rail gun combined with a double-stage light-gas gun.

How the Toughest Inorganic Fullerene Cages Absorb Shockwave Pressures in a Protective Nanocomposite: Experimental Evidence from Two In Situ Investigations.

PubMed

Xu, Fang; Kobayashi, Takamichi; Yang, Zhuxian; Sekine, Toshimori; Chang, Hong; Wang, Nannan; Xia, Yongde; Zhu, Yanqiu

2017-08-22

Nanocomposites fabricated using the toughest caged inorganic fullerene WS 2 (IF-WS 2 ) nanoparticles could offer ultimate protection via absorbing shockwaves; however, if the IF-WS 2 nanomaterials really work, how they behave and what they experience within the nanocomposites at the right moment of impact have never been investigated effectively, due to the limitations of existing investigation techniques that are unable to elucidate the true characteristics of high-speed impacts in composites. We first fabricated Al matrix model nanocomposites and then unlocked the exact roles of IF-WS 2 in it at the exact moment of impact, at a time resolution that has never been attempted before, using two in situ techniques. We find that the presence of IF-WS 2 reduced the impact velocity by over 100 m/s and in pressure by at least 2 GPa against those Al and hexagonal WS 2 platelet composites at an impact speed of 1000 m/s. The IF-WS 2 composites achieved an intriguing inelastic impact and outperformed other reference composites, all originating from the "balloon effect" by absorbing the shockwave pressures. This study not only provides fundamental understanding for the dynamic performance of composites but also benefits the development of protective nanocomposite engineering.

Improving the antioxidant functionality of Citrus junos Tanaka (yuzu) fruit juice by underwater shockwave pretreatment.

PubMed

Kuraya, Eisuke; Nakada, Shina; Touyama, Akiko; Itoh, Shigeru

2017-02-01

Citrus junos Tanaka (yuzu) has a strong characteristic aroma, and hence, yuzu juice is used in a number of Japanese foods. We herein evaluated the functional compounds of yuzu juice to investigate whether underwater shockwave pretreatment affects its functionality. Employing the shockwave pretreatment at an increased discharge and energy of 3.5kV and 4.9kJ, respectively, resulted in an increase in the flavanone glycoside content and oxygen radical absorbance capacity (ORAC). The ORAC value of yuzu juice cultivated in Rikuzentakata increased approximately 1.7 times upon underwater shockwave pretreatment. The treatment method proposed herein exhibited reliable and good performance for the extraction of functional and antioxidant chemicals in yuzu fruits, and was comparable with traditional squeezing methods. The high applicability and reliability of this technique for improving the antioxidant functionality of yuzu fruit juice was demonstrated, confirming the potential for application to a wide range of food extraction processes. Copyright © 2016 Elsevier Ltd. All rights reserved.

Shock-induced bubble jetting into a viscous fluid with application to tissue injury in shock-wave lithotripsy.

PubMed

Freund, J B; Shukla, R K; Evan, A P

2009-11-01

Shock waves in liquids are known to cause spherical gas bubbles to rapidly collapse and form strong re-entrant jets in the direction of the propagating shock. The interaction of these jets with an adjacent viscous liquid is investigated using finite-volume simulation methods. This configuration serves as a model for tissue injury during shock-wave lithotripsy, a medical procedure to remove kidney stones. In this case, the viscous fluid provides a crude model for the tissue. It is found that for viscosities comparable to what might be expected in tissue, the jet that forms upon collapse of a small bubble fails to penetrate deeply into the viscous fluid "tissue." A simple model reproduces the penetration distance versus viscosity observed in the simulations and leads to a phenomenological model for the spreading of injury with multiple shocks. For a reasonable selection of a single efficiency parameter, this model is able to reproduce in vivo observations of an apparent 1000-shock threshold before wide-spread tissue injury occurs in targeted kidneys and the approximate extent of this injury after a typical clinical dose of 2000 shock waves.

Shock-induced bubble jetting into a viscous fluid with application to tissue injury in shock-wave lithotripsy

PubMed Central

Freund, J. B.; Shukla, R. K.; Evan, A. P.

2009-01-01

Shock waves in liquids are known to cause spherical gas bubbles to rapidly collapse and form strong re-entrant jets in the direction of the propagating shock. The interaction of these jets with an adjacent viscous liquid is investigated using finite-volume simulation methods. This configuration serves as a model for tissue injury during shock-wave lithotripsy, a medical procedure to remove kidney stones. In this case, the viscous fluid provides a crude model for the tissue. It is found that for viscosities comparable to what might be expected in tissue, the jet that forms upon collapse of a small bubble fails to penetrate deeply into the viscous fluid “tissue.” A simple model reproduces the penetration distance versus viscosity observed in the simulations and leads to a phenomenological model for the spreading of injury with multiple shocks. For a reasonable selection of a single efficiency parameter, this model is able to reproduce in vivo observations of an apparent 1000-shock threshold before wide-spread tissue injury occurs in targeted kidneys and the approximate extent of this injury after a typical clinical dose of 2000 shock waves. PMID:19894850

EASI - EQUILIBRIUM AIR SHOCK INTERFERENCE

NASA Technical Reports Server (NTRS)

Glass, C. E.

1994-01-01

New research on hypersonic vehicles, such as the National Aero-Space Plane (NASP), has raised concerns about the effects of shock-wave interference on various structural components of the craft. State-of-the-art aerothermal analysis software is inadequate to predict local flow and heat flux in areas of extremely high heat transfer, such as the surface impingement of an Edney-type supersonic jet. EASI revives and updates older computational methods for calculating inviscid flow field and maximum heating from shock wave interference. The program expands these methods to solve problems involving the six shock-wave interference patterns on a two-dimensional cylindrical leading edge with an equilibrium chemically reacting gas mixture (representing, for example, the scramjet cowl of the NASP). The inclusion of gas chemistry allows for a more accurate prediction of the maximum pressure and heating loads by accounting for the effects of high temperature on the air mixture. Caloric imperfections and specie dissociation of high-temperature air cause shock-wave angles, flow deflection angles, and thermodynamic properties to differ from those calculated by a calorically perfect gas model. EASI contains pressure- and temperature-dependent thermodynamic and transport properties to determine heating rates, and uses either a calorically perfect air model or an 11-specie, 7-reaction reacting air model at equilibrium with temperatures up to 15,000 K for the inviscid flowfield calculations. EASI solves the flow field and the associated maximum surface pressure and heat flux for the six common types of shock wave interference. Depending on the type of interference, the program solves for shock-wave/boundary-layer interaction, expansion-fan/boundary-layer interaction, attaching shear layer or supersonic jet impingement. Heat flux predictions require a knowledge (from experimental data or relevant calculations) of a pertinent length scale of the interaction. Output files contain flow-field information for the various shock-wave interference patterns and their associated maximum surface pressure and heat flux predictions. EASI is written in FORTRAN 77 for a DEC VAX 8500 series computer using the VAX/VMS operating system, and requires 75K of memory. The program is available on a 9-track 1600 BPI magnetic tape in DEC VAX BACKUP format. EASI was developed in 1989. DEC, VAX, and VMS are registered trademarks of the Digital Equipment Corporation.

Effects of low-energy shockwave therapy on the erectile function and tissue of a diabetic rat model.

PubMed

Qiu, Xuefeng; Lin, Guiting; Xin, Zhongcheng; Ferretti, Ludovic; Zhang, Haiyang; Lue, Tom F; Lin, Ching-Shwun

2013-03-01

Introduction.  Low-energy shockwave therapy (LESWT) has been shown to improve erectile function in patients suffering from diabetes mellitus (DM)-associated erectile dysfunction (ED). However, the underlying mechanism remains unknown. Aim.  The aim of this study is to investigate whether LESWT can ameliorate DM-associated ED in a rat model and examine the associated changes in the erectile tissues. Methods.  Newborn male rats were intraperitoneally injected with 5-ethynyl-2-deoxyuridine (EdU; 50 mg/kg) for the purpose of tracking endogenous mesenchymal stem cells (MSCs). Eight weeks later, eight of these rats were randomly chosen to serve as normal control (N group). The remaining rats were injected intraperitoneally with 60 mg/kg of streptozotocin (STZ) to induce DM. Eight of these rats were randomly chosen to serve as DM control (DM group), whereas another eight rats were subject to shockwave (SW) treatment (DM+SW group). Each rat in the DM+SW group received 300 shocks at energy level of 0.1 mJ/mm(2) and frequency of 120/minute. This procedure was repeated three times a week for 2 weeks. Another 2 weeks later, all 24 rats were evaluated for erectile function by intracavernous pressure (ICP) measurement. Afterward, their penile tissues were examined by histology. Main Outcome Measures.  Erectile function was measured by ICP. Neuronal nitric oxide synthase (nNOS)-positive nerves and the endothelium were examined by immunofluorescence staining. Smooth muscle and MSCs were examined by phalloidin and EdU staining, respectively. Results.  STZ treatment caused a significant decrease in erectile function and in the number of nNOS-positive nerves and in endothelial and smooth muscle contents. These DM-associated deficits were all partially but significantly reversed by LESWT. MSCs (EdU-positive cells) were significantly more numerous in DM+SW than in DM rats. Conclusion.  LESWT can partially ameliorate DM-associated ED by promoting regeneration of nNOS-positive nerves, endothelium, and smooth muscle in the penis. These beneficial effects appear to be mediated by recruitment of endogenous MSCs. Qiu X, Lin G, Xin Z, Ferretti L, Zhang H, Lue TF, and Lin C-S. Effects of low-energy shockwave therapy on the erectile function and tissue of a diabetic rat model. J Sex Med 2013;10:738-746. © 2012 International Society for Sexual Medicine.

Dynamics of plasma expansion and shockwave formation in femtosecond laser-ablated aluminum plumes in argon gas at atmospheric pressures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miloshevsky, Alexander; Harilal, Sivanandan S.; Miloshevsky, Gennady, E-mail: gennady@purdue.edu

2014-04-15

Plasma expansion with shockwave formation during laser ablation of materials in a background gasses is a complex process. The spatial and temporal evolution of pressure, temperature, density, and velocity fields is needed for its complete understanding. We have studied the expansion of femtosecond (fs) laser-ablated aluminum (Al) plumes in Argon (Ar) gas at 0.5 and 1 atmosphere (atm). The expansion of the plume is investigated experimentally using shadowgraphy and fast-gated imaging. The computational fluid dynamics (CFD) modeling is also carried out. The position of the shock front measured by shadowgraphy and fast-gated imaging is then compared to that obtained frommore » the CFD modeling. The results from the three methods are found to be in good agreement, especially during the initial stage of plasma expansion. The computed time- and space-resolved fields of gas-dynamic parameters have provided valuable insights into the dynamics of plasma expansion and shockwave formation in fs-pulse ablated Al plumes in Ar gas at 0.5 and 1 atm. These results are compared to our previous data on nanosecond (ns) laser ablation of Al [S. S. Harilal et al., Phys. Plasmas 19, 083504 (2012)]. It is observed that both fs and ns plumes acquire a nearly spherical shape at the end of expansion in Ar gas at 1 atm. However, due to significantly lower pulse energy of the fs laser (5 mJ) compared to pulse energy of the ns laser (100 mJ) used in our studies, the values of pressure, temperature, mass density, and velocity are found to be smaller in the fs laser plume, and their time evolution occurs much faster on the same time scale. The oscillatory shock waves clearly visible in the ns plume are not observed in the internal region of the fs plume. These experimental and computational results provide a quantitative understanding of plasma expansion and shockwave formation in fs-pulse and ns-pulse laser ablated Al plumes in an ambient gas at atmospheric pressures.« less

Large-eddy simulation of the passage of a shock wave through homogeneous turbulence

NASA Astrophysics Data System (ADS)

Braun, N. O.; Pullin, D. I.; Meiron, D. I.

2017-11-01

The passage of a nominally plane shockwave through homogeneous, compressible turbulence is a canonical problem representative of flows seen in supernovae, supersonic combustion engines, and inertial confinement fusion. The interaction of isotropic turbulence with a stationary normal shockwave is considered at inertial range Taylor Reynolds numbers, Reλ = 100 - 2500 , using Large Eddy Simulation (LES). The unresolved, subgrid terms are approximated by the stretched-vortex model (Kosovic et al., 2002), which allows self-consistent reconstruction of the subgrid contributions to the turbulent statistics of interest. The mesh is adaptively refined in the vicinity of the shock to resolve small amplitude shock oscillations, and the implications of mesh refinement on the subgrid modeling are considered. Simulations are performed at a range of shock Mach numbers, Ms = 1.2 - 3.0 , and turbulent Mach numbers, Mt = 0.06 - 0.18 , to explore the parameter space of the interaction at high Reynolds number. The LES shows reasonable agreement with linear analysis and lower Reynolds number direct numerical simulations. LANL Subcontract 305963.

Developing Multimedia Courseware for the Internet's Java versus Shockwave.

ERIC Educational Resources Information Center

Majchrzak, Tina L.

1996-01-01

Describes and compares two methods for developing multimedia courseware for use on the Internet: an authoring tool called Shockwave, and an object-oriented language called Java. Topics include vector graphics, browsers, interaction with network protocols, data security, multithreading, and computer languages versus development environments. (LRW)

Cytoplasmic molecular delivery with shock waves: importance of impulse.

PubMed Central

Kodama, T; Hamblin, M R; Doukas, A G

2000-01-01

Cell permeabilization using shock waves may be a way of introducing macromolecules and small polar molecules into the cytoplasm, and may have applications in gene therapy and anticancer drug delivery. The pressure profile of a shock wave indicates its energy content, and shock-wave propagation in tissue is associated with cellular displacement, leading to the development of cell deformation. In the present study, three different shock-wave sources were investigated; argon fluoride excimer laser, ruby laser, and shock tube. The duration of the pressure pulse of the shock tube was 100 times longer than the lasers. The uptake of two fluorophores, calcein (molecular weight: 622) and fluorescein isothiocyanate-dextran (molecular weight: 71,600), into HL-60 human promyelocytic leukemia cells was investigated. The intracellular fluorescence was measured by a spectrofluorometer, and the cells were examined by confocal fluorescence microscopy. A single shock wave generated by the shock tube delivered both fluorophores into approximately 50% of the cells (p < 0.01), whereas shock waves from the lasers did not. The cell survival fraction was >0.95. Confocal microscopy showed that, in the case of calcein, there was a uniform fluorescence throughout the cell, whereas, in the case of FITC-dextran, the fluorescence was sometimes in the nucleus and at other times not. We conclude that the impulse of the shock wave (i.e., the pressure integrated over time), rather than the peak pressure, was a dominant factor for causing fluorophore uptake into living cells, and that shock waves might have changed the permeability of the nuclear membrane and transferred molecules directly into the nucleus. PMID:11023888

Numerical Investigations of the Influence of Unsteady Vane Trailing Edge Shock Wave on Film Cooling Effectiveness of Rotor Blade Leading Edge

NASA Astrophysics Data System (ADS)

Wang, Yufeng; Cai, Le; Wang, Songtao; Zhou, Xun

2018-04-01

Unsteady numerical simulations of a high-load transonic turbine stage have been carried out to study the influences of vane trailing edge outer-extending shockwave on rotor blade leading edge film cooling performance. The turbine stage used in this paper is composed of a vane section and a rotor one which are both near the root section of a transonic high-load turbine stage. The Mach number is 0.94 at vane outlet, and the relative Mach number is above 1.10 at rotor outlet. Various positions and oblique angles of film cooling holes were investigated in this research. Results show that the cooling efficiency on the blade surface of rotor near leading edge is significantly affected by vane trailing edge outer-extending shockwave in some cases. In the cases that film holes are close to leading edge, cooling performance suffers more from the sweeping vane trailing edge outer-extending shockwave. In addition, coolant flow ejected from oblique film holes is harder to separate from the blade surface of rotor, and can cover more blade area even under the effects of sweeping vane trailing edge shockwave. As a result, oblique film holes can provide better film cooling performance than vertical film holes do near the leading edge on turbine blade which is swept by shockwaves.

Infrasound and Seismic Observation of Hayabusa Reentry as An Artificial Meteorite Fall

NASA Astrophysics Data System (ADS)

Ishihara, Y.; Hiramatsu, Y.; Yamamoto, M.; Furumoto, M.; Fujita, K.

2011-12-01

The Hayabusa, the world first sample-return minor body explorer, came back to the Earth, and reentered into the Earth's atmosphere on June 13, 2010. Following the reentries of the Genesis in 2004 and the Stardust in 2006, the return of the Hayabusa Sample Return Capsule (H-SRC) was the third direct reentry event from the interplanetary transfer orbit to the Earth at a velocity of over 11.2 km/s. In addition, it was the world first case of the direct reentry of the spacecraft (H-S/C) itself from the interplanetary transfer orbit. The H-SRC and the H-S/C reentries are very good analogue for studying bolide size meteors and meteorite falls. We, therefore, conducted a ground observation campaign for aspects of meteor sciences. We carried out multi-site ground observations of the Hayabusa reentry in the Woomera Prohibited Area (WPA), Australia. The observations were configured with optical imaging with still and video recordings, spectroscopies, and shockwave detection with infrasound and seismic sensors. In this study, we report details of the infrasound/seismic observations and those results. To detect shockwaves from the H-SRC and the H-S/C, we installed three small aperture infrasound/seismic arrays as the main stations. In addition, we also installed three single component seismic sub stations and an audible sound recorder. The infrasound and seismic sensors clearly recorded sonic boom type shockwaves from the H-SRC and disrupted fragments of the H-S/C itself. The audible recording also detected those shockwave sounds in the human audible band. Positive overpressure values of shockwaves (corresponding to the H-SRC) recorded at three main stations are 1.3 Pa, 1.0 Pa, and 0.7 Pa with the slant distance of 36.9 km, 54.9 km, and 67.8 km (i.e., the source altitude of 36.5 km, 38.9km, and 40.6 km), respectively. These amplitudes of shockwave overpressures are systematically smaller than those of theoretical predictions. We tried to identify the sources of shockwaves signals from the disrupted fragments as optically identified fragments of the H-S/C. In comparison between the infrasonic pressure waves and the video image analyses, the generation of sonic boom type shockwaves by the both of the H-SRC and fragmented parts of the H-S/C at an altitude of 40±1 km was confirmed with one-to-one correspondence with each other. The incident vectors of the shockwave from the H-SRC at all the three arrays are estimated by F-K spectrum and agree well with predicted ones. Particle motions of ground motions excited by the shockwave from the H-SRC show characteristics of typical Rayleigh wave. In addition, we examine the relationship between amplitudes of those ground motions and overpressure values correspond to the H-SRC. We compare amplitudes of ground motions detected by seismometers to theoretical estimations of air-to-ground coupling. In calculations, we have used amplitudes of observed overpressures by infrasound sensors as incident pressure waves and elastic moduli of each site are obtained by H/V spectrum analysis. The observed amplitudes of the ground motions are almost consistent with the theoretical estimations.

A meta-analysis of the effects of shockwave and high pressure processing on color and cook loss of fresh meat.

PubMed

Ha, Minh; Dunshea, Frank R; Warner, Robyn D

2017-10-01

Meta-analysis is a statistical approach for investigating experimental differences across studies. Meta-analyses were performed to examine the effects of hydrodynamic processing (shockwave; n=12 papers) and high pressure processing (HPP; n=8 papers) on the color and cook loss of fresh meat. Shockwave did not affect color (L*, a*), whereas cook loss was increased by 0.6% relative to untreated meat. HPP resulted in an increase in lightness (L*) and a decrease in redness (a*), with the effect being greater at higher pressures (>300MPa vs <300MPa). In addition, HPP applied at moderate pressure (<300MPa) reduced cook loss but at high pressure (>300MPa) the cook loss was increased (-1.5% vs 3.0% respectively). The increased cook loss with shockwave and high pressure (>300MPa) processing needs to be balanced against benefits in texture if this technology is applied to meat. The reduced cook loss of meat treated at moderate pressures (<300MPa) is an advantage which would likely improve sensory traits. Copyright © 2017 Elsevier Ltd. All rights reserved.

New sonic shockwave multi-element sensors mounted on a small airfoil flown on F-15B testbed aircraft

NASA Technical Reports Server (NTRS)

1996-01-01

An experimental device to pinpoint the location of a shockwave that develops in an aircraft flying at transonic and supersonic speeds was recently flight-tested at NASA's Dryden Flight Research Center, Edwards, California. The shock location sensor, developed by TAO Systems, Hampton, Va., utilizes a multi-element hot-film sensor array along with a constant-voltage anemometer and special diagnostic software to pinpoint the exact location of the shockwave and its characteristics as it develops on an aircraft surface. For this experiment, the 45-element sensor was mounted on the small Dryden-designed airfoil shown in this illustration. The airfoil was attached to the Flight Test Fixture mounted underneath the fuselage of Dryden's F-15B testbed aircraft. Tests were flown at transonic speeds of Mach 0.7 to 0.9, and the device isolated the location of the shock wave to within a half-inch. Application of this technology could assist designers of future supersonic aircraft in improving the efficiency of engine air inlets by controlling the shockwave, with a related improvement in aircraft performance and fuel economy.

Metallic glass formation at the interface of explosively welded Nb and stainless steel

NASA Astrophysics Data System (ADS)

Bataev, I. A.; Hokamoto, K.; Keno, H.; Bataev, A. A.; Balagansky, I. A.; Vinogradov, A. V.

2015-07-01

The interface between explosively welded niobium and stainless steel SUS 304 was studied using scanning electron microscopy, transmission electron microscopy and energy dispersive X-Ray spectroscopy. The wavy interface along which vortex zones were located was observed. The vortex zones formed due to the mixing of materials typically had amorphous structure. Inoue's criteria of glass formation were used to explain this result. The effect of the composition, cooling rate and pressure on the glass formation are discussed. The conditions of deformation, heating, and cooling as well as shockwaves propagation were numerically simulated. We show that the conditions of vortex zone formation resemble the conditions of rapid solidification processes. In contrast to the "classical" methods of rapid solidification of melt, the conditions of metastable phase formation during explosive welding are significantly complicated by the fluctuations of composition and pressure. Possible metastable structures formation at the interface of some common explosively joined materials is predicted.

Dissipative processes under the shock compression of glass

NASA Astrophysics Data System (ADS)

Savinykh, A. S.; Kanel, G. I.; Cherepanov, I. A.; Razorenov, S. V.

2016-03-01

New experimental data on the behavior of the K8 and TF1 glasses under shock-wave loading conditions are obtained. It is found that the propagation of shock waves is close to the self-similar one in the maximum compression stress range 4-12 GPa. Deviations from a general deformation diagram, which are related to viscous dissipation, take place when the final state of compression is approached. The parameter region in which failure waves form in glass is found not to be limited to the elastic compression stress range, as was thought earlier. The failure front velocity increases with the shock compression stress. Outside the region covered by a failure wave, the glasses demonstrate a high tensile dynamic strength (6-7 GPa) in the case of elastic compression, and this strength is still very high after transition through the elastic limit in a compression wave.

Frontiers in Anisotropic Shock-Wave Modeling

DTIC Science & Technology

2012-02-01

Nowadays, some models incorporate a user-defined subroutine within the commercial software (e.g., ABAQUS ) to take into account either a homogenous...and temperature on the mass density. The specific internal energy can be decomposed into potentials describing the cold compression, ec (ρ, S); thermal ...Taylor’s series expansion of the Hugoniot pressure P . Assume that the linear approximation between the shock velocity US 24 and particle velocity up

An Investigation of the High Rate Volumetric Properties of Snow.

DTIC Science & Technology

1981-11-01

experimental data. A number of applications are thenLi Investigated. These applications Include vehicle mobility In shallow anddeep snowpack, steady shockwaves...applications include vehicle mobility : in cb11 low and deep sjnowpack, ,,teady shockwaves, and noiistieady oe.av. -An na, 1, -lromacgnetic -;Lrus...VEHICLE MOBILITY ........................ 48 . III.A. Introductory Remarks .................................... 48 111.0. Tracked Vehicle Mobility in

Prospects in straw disintegration for biogas production.

PubMed

Maroušek, Josef

2013-10-01

The pretreatment methods for enhancing biogas production from oat straw under study include hot maceration, steam explosion, and pressure shockwaves. The micropore area (9, 55, and 64 m(2) g(-1)) inhibitor formations (0, 15, and 0 mL L(-1)) as well as the overall methane yields (67, 179, and 255 CH4 VS t(-1)) were robustly analyzed. It was confirmed that the operating conditions of the steam explosion must be precisely tailored to the substrate. Furthermore, it was beneficial to prepend the hot maceration before the steam explosion and the pressure shockwaves. The second alternative may give increased methane yields (246 in comparison to 273 CH4 VS t(-1)); however, the application of pressure shockwaves still faces limitations for deployment on a commercial scale.

Impact of ablator thickness and laser drive duration on a platform for supersonic, shockwave-driven hydrodynamic instability experiments

DOE PAGES

Wan, W. C.; Malamud, Guy; Shimony, A.; ...

2016-12-07

Here, we discuss changes to a target design that improved the quality and consistency of data obtained through a novel experimental platform that enables the study of hydrodynamic instabilities in a compressible regime. The experiment uses a laser to drive steady, supersonic shockwave over well-characterized initial perturbations. Early experiments were adversely affected by inadequate experimental timescales and, potentially, an unintended secondary shockwave. These issues were addressed by extending the 4 x 10 13 W/cm 2 laser pulse from 19 ns to 28 ns, and increasing the ablator thickness from 185 µm to 500 µm. We present data demonstrating the performancemore » of the platform.« less

Impact of ablator thickness and laser drive duration on a platform for supersonic, shockwave-driven hydrodynamic instability experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wan, W. C.; Malamud, Guy; Shimony, A.

Here, we discuss changes to a target design that improved the quality and consistency of data obtained through a novel experimental platform that enables the study of hydrodynamic instabilities in a compressible regime. The experiment uses a laser to drive steady, supersonic shockwave over well-characterized initial perturbations. Early experiments were adversely affected by inadequate experimental timescales and, potentially, an unintended secondary shockwave. These issues were addressed by extending the 4 x 10 13 W/cm 2 laser pulse from 19 ns to 28 ns, and increasing the ablator thickness from 185 µm to 500 µm. We present data demonstrating the performancemore » of the platform.« less

Quantum molecular dynamics simulation of shock-wave experiments in aluminum

NASA Astrophysics Data System (ADS)

Minakov, D. V.; Levashov, P. R.; Khishchenko, K. V.; Fortov, V. E.

2014-06-01

We present quantum molecular dynamics calculations of principal, porous, and double shock Hugoniots, release isentropes, and sound velocity behind the shock front for aluminum. A comprehensive analysis of available shock-wave data is performed; the agreement and discrepancies of simulation results with measurements are discussed. Special attention is paid to the melting region of aluminum along the principal Hugoniot; the boundaries of the melting zone are estimated using the self-diffusion coefficient. Also, we make a comparison with a high-quality multiphase equation of state for aluminum. Independent semiempirical and first-principle models are very close to each other in caloric variables (pressure, density, particle velocity, etc.) but the equation of state gives higher temperature on the principal Hugoniot and release isentropes than ab initio calculations. Thus, the quantum molecular dynamics method can be used for calibration of semiempirical equations of state in case of lack of experimental data.

Quantum molecular dynamics simulation of shock-wave experiments in aluminum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Minakov, D. V.; Khishchenko, K. V.; Fortov, V. E.

2014-06-14

We present quantum molecular dynamics calculations of principal, porous, and double shock Hugoniots, release isentropes, and sound velocity behind the shock front for aluminum. A comprehensive analysis of available shock-wave data is performed; the agreement and discrepancies of simulation results with measurements are discussed. Special attention is paid to the melting region of aluminum along the principal Hugoniot; the boundaries of the melting zone are estimated using the self-diffusion coefficient. Also, we make a comparison with a high-quality multiphase equation of state for aluminum. Independent semiempirical and first-principle models are very close to each other in caloric variables (pressure, density,more » particle velocity, etc.) but the equation of state gives higher temperature on the principal Hugoniot and release isentropes than ab initio calculations. Thus, the quantum molecular dynamics method can be used for calibration of semiempirical equations of state in case of lack of experimental data.« less

Shockwave treatment for medial tibial stress syndrome: A randomized double blind sham-controlled pilot trial.

PubMed

Newman, Phil; Waddington, Gordon; Adams, Roger

2017-03-01

Up to 35% of runners develop medial tibial stress syndrome (MTSS) which often results in lengthy disruption to training and sometimes affects daily activities. There is currently no high quality evidence to support any particular intervention for MTSS. This study aims to investigate the effect of shockwave therapy for MTSS. A randomized, sham-controlled, pilot trial in a university-based health clinic including 28 active adults with MTSS. Intervention included standard dose shockwave therapy for the experimental group versus sham dose for the control group, delivered during Week 1-3, 5 and 9. Main outcome measures were pain measured during bone and muscle pressure as well as during running using a numerical rating scale (0-10) and running was measured as pain-limited distance (m), at Week 1 (baseline) and Week 10 (post-intervention). Self-perception of change was measured using the Global Rating of Change Scale (-7 to +7) at Week 10 (post-intervention). Pain (palpation) was reduced in the experimental group by 1.1 out of 10.0 (95% CI -2.3 to 0.0) less than the control group. There were no other statistically significant differences between the groups. Standard dose shockwave therapy is not more effective than sham dose at improving pain or running distance in MTSS. However, the sham dose may have had a clinical effect. Further investigation including a no intervention control is warranted to evaluate the effect of shockwave therapy in the management of MTSS. Copyright © 2016 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Recent developments in SWL physics research.

PubMed

Zhong, P; Xi, X; Zhu, S; Cocks, F H; Preminger, G M

1999-11-01

Two projects in our laboratory highlight some recent developments in shockwave lithotripsy (SWL) physics research. In the first project, we developed a prototype of a piezoelectric annular array (PEAA) shockwave generator that can be retrofitted on a Dornier HM-3 lithotripter for active control of cavitation during SWL. The PEAA generator, operating at 15 kV, produces a peak positive pressure of approximately 8 MPa with a -6-dB beam diameter of 5 mm. The shockwave generated by the PEAA was used to control and force the collapse of cavitation bubbles induced by a laboratory electrohydraulic shockwave lithotripter with a truncated HM-3 reflector. With optimal time delay between the lithotripter pulse and the PEAA-generated shockwave, the collapse of cavitation bubbles near the stone surface could be intensified, and the resultant stone fragmentation in vitro could be significantly improved. In the second project, high-speed shadowgraph imaging was used to visualize the dynamics of lithotripter-induced bubble oscillation in a vascular phantom. Compared with the free bubble oscillation in water, the expansion of cavitation bubble(s) produced in silicone tubes and a 200-microm cellulose hollow fiber by either a Nortech EHL or a Dornier XL-1 lithotripter was found to be significantly constrained. Rupture of the cellulose hollow fiber was observed consistently after about 20 shocks from the XL-1 lithotripter at an output voltage of 20 kV. These results confirm experimentally that SWL-induced cavitation in vivo can be significantly constrained by the surrounding tissue, and large intraluminal bubble expansions could cause rupture of capillaries and small blood vessels.

A Multi-Mode Shock Tube for Investigation of Blast-Induced Traumatic Brain Injury

PubMed Central

Reneer, Dexter V.; Hisel, Richard D.; Hoffman, Joshua M.; Kryscio, Richard J.; Lusk, Braden T.

2011-01-01

Abstract Blast-induced mild traumatic brain injury (bTBI) has become increasingly common in recent military conflicts. The mechanisms by which non-impact blast exposure results in bTBI are incompletely understood. Current small animal bTBI models predominantly utilize compressed air-driven membrane rupture as their blast wave source, while large animal models use chemical explosives. The pressure-time signature of each blast mode is unique, making it difficult to evaluate the contributions of the different components of the blast wave to bTBI when using a single blast source. We utilized a multi-mode shock tube, the McMillan blast device, capable of utilizing compressed air- and compressed helium-driven membrane rupture, and the explosives oxyhydrogen and cyclotrimethylenetrinitramine (RDX, the primary component of C-4 plastic explosives) as the driving source. At similar maximal blast overpressures, the positive pressure phase of compressed air-driven blasts was longer, and the positive impulse was greater, than those observed for shockwaves produced by other driving sources. Helium-driven shockwaves more closely resembled RDX blasts, but by displacing air created a hypoxic environment within the shock tube. Pressure-time traces from oxyhydrogen-driven shockwaves were very similar those produced by RDX, although they resulted in elevated carbon monoxide levels due to combustion of the polyethylene bag used to contain the gases within the shock tube prior to detonation. Rats exposed to compressed air-driven blasts had more pronounced vascular damage than those exposed to oxyhydrogen-driven blasts of the same peak overpressure, indicating that differences in blast wave characteristics other than peak overpressure may influence the extent of bTBI. Use of this multi-mode shock tube in small animal models will enable comparison of the extent of brain injury with the pressure-time signature produced using each blast mode, facilitating evaluation of the blast wave components contributing to bTBI. PMID:21083431

A multi-mode shock tube for investigation of blast-induced traumatic brain injury.

PubMed

Reneer, Dexter V; Hisel, Richard D; Hoffman, Joshua M; Kryscio, Richard J; Lusk, Braden T; Geddes, James W

2011-01-01

Blast-induced mild traumatic brain injury (bTBI) has become increasingly common in recent military conflicts. The mechanisms by which non-impact blast exposure results in bTBI are incompletely understood. Current small animal bTBI models predominantly utilize compressed air-driven membrane rupture as their blast wave source, while large animal models use chemical explosives. The pressure-time signature of each blast mode is unique, making it difficult to evaluate the contributions of the different components of the blast wave to bTBI when using a single blast source. We utilized a multi-mode shock tube, the McMillan blast device, capable of utilizing compressed air- and compressed helium-driven membrane rupture, and the explosives oxyhydrogen and cyclotrimethylenetrinitramine (RDX, the primary component of C-4 plastic explosives) as the driving source. At similar maximal blast overpressures, the positive pressure phase of compressed air-driven blasts was longer, and the positive impulse was greater, than those observed for shockwaves produced by other driving sources. Helium-driven shockwaves more closely resembled RDX blasts, but by displacing air created a hypoxic environment within the shock tube. Pressure-time traces from oxyhydrogen-driven shockwaves were very similar those produced by RDX, although they resulted in elevated carbon monoxide levels due to combustion of the polyethylene bag used to contain the gases within the shock tube prior to detonation. Rats exposed to compressed air-driven blasts had more pronounced vascular damage than those exposed to oxyhydrogen-driven blasts of the same peak overpressure, indicating that differences in blast wave characteristics other than peak overpressure may influence the extent of bTBI. Use of this multi-mode shock tube in small animal models will enable comparison of the extent of brain injury with the pressure-time signature produced using each blast mode, facilitating evaluation of the blast wave components contributing to bTBI.

Two-zone elastic-plastic single shock waves in solids.

PubMed

Zhakhovsky, Vasily V; Budzevich, Mikalai M; Inogamov, Nail A; Oleynik, Ivan I; White, Carter T

2011-09-23

By decoupling time and length scales in moving window molecular dynamics shock-wave simulations, a new regime of shock-wave propagation is uncovered characterized by a two-zone elastic-plastic shock-wave structure consisting of a leading elastic front followed by a plastic front, both moving with the same average speed and having a fixed net thickness that can extend to microns. The material in the elastic zone is in a metastable state that supports a pressure that can substantially exceed the critical pressure characteristic of the onset of the well-known split-elastic-plastic, two-wave propagation. The two-zone elastic-plastic wave is a general phenomenon observed in simulations of a broad class of crystalline materials and is within the reach of current experimental techniques.

Investigation of Three-Dimensional Unsteady Flow Characteristics in Transonic Diffusers

NASA Astrophysics Data System (ADS)

Proshchanka, Dzianis; Yonezawa, Koichi; Tsujimoto, Yoshinobu

Three-dimensional characteristics of unsteady flow in supercritical transonic diffuser are investigated. For various pressure ratios three-dimensional flow containing a normal shock/turbulent boundary layer interaction regions with shockwave and pseudo-shockwaves fluctuating in longitudinal and spanwise directions is observed. Experimental and numerical investigations show details of the flowfield in the vicinity of terminal shock, interaction regions and downstream turbulent unsteady flow. Spectral analysis of pressure fluctuations reveals existence of two characteristic frequencies attributed to the shockwave fluctuation in longitudinal direction for the lower frequency case and acoustic resonance in spanwise direction for the higher one. Vortices appear at each corner in transversal sections modifying the core flow. As a result, size and depth of longitudinal and vertical penetration of separation regions impelled by the terminal shock is either increased or decreased.

Shock wave induced damage of a protein by void collapse

DOE PAGES

Lau, Edmond Y.; Berkowitz, Max L.; Schwegler, Eric R.

2016-01-05

In this study, we report on a series of molecular dynamics simulations that were used to examine the effects of shockwaves on a membrane bound ion channel. A planar shockwave was found to compress the ion channel upon impact but the protein geometry resembles the initial structure as soon as the solvent density begins to dissipate. When a void was placed in close proximity to the membrane, the shockwave proved to be much more destructive to the protein due to formation of a nanojet that results from the asymmetric collapse of the void. The nanojet was able to cause significantmore » structural changes to the protein even at low particle velocities that are not able to directly cause poration of the membrane.« less

Extracorporeal shockwave enhanced regeneration of fibrocartilage in a delayed tendon-bone insertion repair model.

PubMed

Chow, Dick Ho Kiu; Suen, Pui Kit; Huang, Le; Cheung, Wing-Hoi; Leung, Kwok-Sui; Ng, Chun; Shi, San Qiang; Wong, Margaret Wan Nar; Qin, Ling

2014-04-01

Fibrous tissue is often formed in delayed healing of tendon bone insertion (TBI) instead of fibrocartilage. Extracorporeal shockwave (ESW) provides mechanical cues and upregulates expression of fibrocartilage-related makers and cytokines. We hypothesized that ESW would accelerate fibrocartilage regeneration at the healing interface in a delayed TBI healing model. Partial patellectomy with shielding at the TBI interface was performed on 32 female New Zealand White Rabbits for establishing this delayed TBI healing model. The rabbits were separated into the control and ESW group for evaluations at postoperative week 8 and 12. Shielding was removed at week 4 and a single ESW treatment was applied at week 6. Fibrocartilage regeneration was evaluated histomorphologically and immunohistochemically. Vickers hardness of the TBI matrix was measured by micro-indentation. ESW group showed higher fibrocartilage area, thickness, and proteoglycan deposition than the control in week 8 and 12. ESW increased expression of SOX9 and collagen II significantly in week 8 and 12, respectively. ESW group showed a gradual transition of hardness from bone to fibrocartilage to tendon, and had a higher Vickers hardness than the control group at week 12. In conclusion, ESW enhanced fibrocartilage regeneration at the healing interface in a delayed TBI healing model. © 2013 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

An anisotropic elastoplastic constitutive formulation generalised for orthotropic materials

NASA Astrophysics Data System (ADS)

Mohd Nor, M. K.; Ma'at, N.; Ho, C. S.

2018-03-01

This paper presents a finite strain constitutive model to predict a complex elastoplastic deformation behaviour that involves very high pressures and shockwaves in orthotropic materials using an anisotropic Hill's yield criterion by means of the evolving structural tensors. The yield surface of this hyperelastic-plastic constitutive model is aligned uniquely within the principal stress space due to the combination of Mandel stress tensor and a new generalised orthotropic pressure. The formulation is developed in the isoclinic configuration and allows for a unique treatment for elastic and plastic orthotropy. An isotropic hardening is adopted to define the evolution of plastic orthotropy. The important feature of the proposed hyperelastic-plastic constitutive model is the introduction of anisotropic effect in the Mie-Gruneisen equation of state (EOS). The formulation is further combined with Grady spall failure model to predict spall failure in the materials. The proposed constitutive model is implemented as a new material model in the Lawrence Livermore National Laboratory (LLNL)-DYNA3D code of UTHM's version, named Material Type 92 (Mat92). The combination of the proposed stress tensor decomposition and the Mie-Gruneisen EOS requires some modifications in the code to reflect the formulation of the generalised orthotropic pressure. The validation approach is also presented in this paper for guidance purpose. The \\varvec{ψ} tensor used to define the alignment of the adopted yield surface is first validated. This is continued with an internal validation related to elastic isotropic, elastic orthotropic and elastic-plastic orthotropic of the proposed formulation before a comparison against range of plate impact test data at 234, 450 and {895 ms}^{-1} impact velocities is performed. A good agreement is obtained in each test.

Shock-wave structure based on the Navier-Stokes-Fourier equations.

PubMed

Uribe, F J; Velasco, R M

2018-04-01

We use the Navier-Stokes-Fourier constitutive equations to study plane shock waves in dilute gases. It is shown that the experimental information on the normalized density profiles can be fit by using the so-called soft sphere model, in which the viscosity and thermal conductivity are proportional to a power of the temperature.

Shock-wave structure based on the Navier-Stokes-Fourier equations

NASA Astrophysics Data System (ADS)

Uribe, F. J.; Velasco, R. M.

2018-04-01

We use the Navier-Stokes-Fourier constitutive equations to study plane shock waves in dilute gases. It is shown that the experimental information on the normalized density profiles can be fit by using the so-called soft sphere model, in which the viscosity and thermal conductivity are proportional to a power of the temperature.

Control of the flow over wing airfoils in transonic regimes by means of force action of surface elements on the flow

NASA Astrophysics Data System (ADS)

Aul'chenko, S. M.; Zamuraev, V. P.

2012-09-01

Mathematical modeling of the effect of force oscillations of surface elements of a wing airfoil on the shock-wave structure of the transonic flow over it is implemented. The qualitative and quantitative effect of the oscillation parameters on the airfoil wave drag is investigated.

Sharp plasma pinnacle structure based on shockwave for an improved laser wakefield accelerator

NASA Astrophysics Data System (ADS)

Fang, Ming; Zhang, Zhijun; Wang, Wentao; Liu, Jiansheng; Li, Ruxin

2018-07-01

We created a sharp plasma pinnacle structure for localized electron injection and controlled acceleration in a laser wakefield accelerator. The formation of this shockwave-based pinnacle structure was investigated using aerodynamic theory. Details and scaling laws for the shockwave angle, shock position, shock width, and density ratio were experimentally and theoretically presented. Such work is crucial to yielding an expected plasma density distribution in a laser–plasma experiment but has had little discussion in the literature. Compared with the commonly used shock downramp structure, the particle-in-cell simulations demonstrated that the e beam injected in the created pinnacle structure could be accelerated to higher energy with much smaller root-mean-square relative energy spread. Moreover, this study indicated that the beam charge and transverse emittance can be tuned by the shock angle.

Study of the effects of Shockwaves on Nano fluids

NASA Astrophysics Data System (ADS)

Shreekhar; Akhil, Mohan; Ram, Sai; Gopaiah, Venkata; Koundinya, Sandeep; Nagaraja, S. R.

2018-02-01

Nanofluids are fluids with nanoparticles dispersed in them. Due to the presence of Nano particles, these fluids exhibit unique properties that can used in various applications such as heat exchangers and in medical fields. However, due to agglomeration, the size of these particle increases, reducing their efficiency. In order to break the agglomeration, we are passing shockwaves in the fluid. Shockwaves theoretically carry energy which can be used to break the agglomerating particles. In this paper, silver nanoparticles were synthesized using silver nitrate. Tri sodium citrate was used as the reducing agent. Shock waves were passed to the fluid containing silver Nano particles. The changes in the Nano fluid was measured by a UV-Vis Spectrophotometer. With each shock passed, the fluid’s absorbance and wavelength peak was measured and compared with Nano fluid without shock.

Hazards and Possibilities of Optical Breakdown Effects Below the Threshold for Shockwave and Bubble Formation

DTIC Science & Technology

2006-07-01

precision of the determination of Rmax, we established a refined method based on the model of bubble formation described above in section 3.6.1 and the...development can be modeled by hydrodynamic codes based on tabulated equation-of-state data . This has previously demonstrated on ps optical breakdown...per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and

The Role of PP2A Methylation in Susceptibility and Resistance to TBI and AD-Induced Neurodegeneration

DTIC Science & Technology

2013-09-01

will exert similar effects on shockwave- induced impairments. This effort has required a substantial investment in developing equipment and testing...substantial investment to identify suitable shockwave exposure conditions, confirm biomechanical parameters, and to assess the biochemical...consequences. One of the previously unforeseen benefits of this investment may be the identification of PME-1 over expressing mice as a sensitized background

Comparison of hydrodynamic simulations with two-shockwave drive target experiments

NASA Astrophysics Data System (ADS)

Karkhanis, Varad; Ramaprabhu, Praveen; Buttler, William

2015-11-01

We consider hydrodynamic continuum simulations to mimic ejecta generation in two-shockwave target experiments, where metallic surface is loaded by two successive shock waves. Time of second shock in simulations is determined to match experimental amplitudes at the arrival of the second shock. The negative Atwood number (A --> - 1) of ejecta simulations leads to two successive phase inversions of the interface corresponding to the passage of the shocks from heavy to light media in each instance. Metallic phase of ejecta (solid/liquid) depends on shock loading pressure in the experiment, and we find that hydrodynamic simulations quantify the liquid phase ejecta physics with a fair degree of accuracy, where RM instability is not suppressed by the strength effect. In particular, we find that our results of free surface velocity, maximum ejecta velocity, and maximum ejecta areal density are in excellent agreement with their experimental counterparts, as well as ejecta models. We also comment on the parametric space for hydrodynamic simulations in which they can be used to compare with the target experiments.

Relating climate change policy to poverty policy: assessing the global exposure of the poor to floods and droughts

NASA Astrophysics Data System (ADS)

Winsemius, Hessel; Jongman, Brenden; Veldkamp, Ted; Hallegatte, Stéphane; Bangalore, Mook; Ward, Philip

2016-04-01

Prior to the COP21 conference in Paris this year, the World Bank published a report called "Shockwaves - Managing the Impacts of Climate Change on Poverty". The report flagged that ending poverty and stabilizing climate change should be jointly tackled and that without a good joint policy, a further 100 million people could become trapped in poverty by 2050. As part of the "Shockwaves" report, we investigated whether low-income households are disproportionately overrepresented in hazard-prone areas compared to households with higher income. Furthermore, the hazardous conditions under which poor households are exposed to now may become worse due to climate change with resulting increases in intensity and frequency of floods and droughts. We also show how the amount of affected people to these natural hazards change in the future if nothing is done. We use recent advances in the global spatial modeling of flood and drought hazard and a large sample of household surveys containing asset and income data to explore the relationships.

Estimating the pressure of laser-induced plasma shockwave by stimulated Raman shift of lattice translational modes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li Zhanlong; College of Physics, Jilin University, Changchun 130012; Shan Xiaoning

2012-07-09

The current paper investigates stimulated Raman scattering (SRS) when laser-induced plasma is formed in heavy water by focusing an intense pulsed 532 nm Nd:YAG laser beam at room temperature. An unexpected low-frequency SRS line attributed to the lattice translational modes of ice-VII (D{sub 2}O) is observed. The pressure of the plasma shockwave is estimated using low-frequency SRS line shift.

A new mathematical approach for shock-wave solution in a dusty plasma

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, G.C.; Dwivedi, C.B.; Talukdar, M.

1997-12-01

The problem of nonlinear Burger equation in a plasma contaminated with heavy dust grains has been revisited. As discussed earlier [C. B. Dwivedi and B. P. Pandey, Phys. Plasmas {bold 2}, 9 (1995)], the Burger equation originates due to dust charge fluctuation dynamics. A new alternate mathematical approach based on a simple traveling wave formalism has been applied to find out the solution of the derived Burger equation, and the method recovers the known shock-wave solution. This technique, although having its own limitation, predicts successfully the salient features of the weak shock-wave structure in a dusty plasma with dust chargemore » fluctuation dynamics. It is emphasized that this approach of the traveling wave formalism is being applied for the first time to solve the nonlinear wave equation in plasmas. {copyright} {ital 1997 American Institute of Physics.}« less

Extracorporeal shockwave lithotripsy in the management of salivary calculi.

PubMed

Escudier, M P; Brown, J E; Drage, N A; McGurk, M

2003-04-01

The aim was to investigate the results of extracorporeal shockwave lithotripsy in the management of salivary calculi using a dedicated sialolithotriptor. Some 122 salivary calculi (84 submandibular and 38 parotid) were treated in an experimental study using a sialolithotriptor. Complete success was achieved in 40 procedures (33 per cent), 27 of 84 submandibular and 13 of 38 parotid calculi. A further 43 patients (35 per cent) were rendered asymptomatic although some stone debris remained in the duct (26 submandibular and 17 parotid). Failure (retention of stone debris and continued symptoms) occurred in 39 patients (32 per cent), 30 submandibular and eight parotid glands. The chance of failure increased with the size of the calculus and increasing duration of symptoms. Extracorporeal shockwave lithotripsy provides a useful option for the management of salivary calculi, particularly for stones less than 7 mm in diameter. Copyright 2003 British Journal of Surgery Society Ltd. Published by John Wiley & Sons, Ltd.

Shadowgraphic investigations into the laser-induced forward transfer of different SnO2 precursor films

NASA Astrophysics Data System (ADS)

Mattle, Thomas; Shaw-Stewart, James; Hintennach, Andreas; Schneider, Christof W.; Lippert, Thomas; Wokaun, Alexander

2013-08-01

Laser-induced forward transfer of different SnO2 precursor films for sensor applications were investigated using time resolved imaging, from 0 to 2 μs after the onset of the ablation process. Transfers of SnCl2(acac)2 and SnO2 nano-particles, both with and without a triazene polymer dynamic release layer (DRL), were investigated and compared to transfers of aluminum films with a triazene polymer DRL. Shockwave speed and flyer speeds at high laser fluences of Φ = 650 mJ/cm2 and at the lower fluences, suitable for the transfer of functional and well defined pixels were analyzed. No influence of the use of a triazene polymer DRL on shockwave and flyer speed was observed. Material ejected under transfer condition showed a velocity of around 200 m/s with a weak shockwave.

Reducing the wave drag of wing airfoils in transonic flow regimes by the force action of airfoil surface elements on the flow

NASA Astrophysics Data System (ADS)

Aul'chenko, S. M.; Zamuraev, V. P.

2012-11-01

Mathematical modeling of the influence of forced oscillations of surface elements of a wing airfoil on the shock-wave structure of transonic flow past it has been carried out. The qualitative and quantitative influence of the oscillation parameters on the wave drag of the airfoil has been investigated.

Time-resolved spectroscopic measurements of shock-wave induced decomposition in cyclotrimethylene trinitramine (RDX) crystals: anisotropic response.

PubMed

Dang, Nhan C; Dreger, Zbigniew A; Gupta, Yogendra M; Hooks, Daniel E

2010-11-04

Plate impact experiments on the (210), (100), and (111) planes were performed to examine the role of crystalline anisotropy on the shock-induced decomposition of cyclotrimethylenetrinitramine (RDX) crystals. Time-resolved emission spectroscopy was used to probe the decomposition of single crystals shocked to peak stresses ranging between 7 and 20 GPa. Emission produced by decomposition intermediates was analyzed in terms of induction time to emission, emission intensity, and the emission spectra shapes as a function of stress and time. Utilizing these features, we found that the shock-induced decomposition of RDX crystals exhibits considerable anisotropy. Crystals shocked on the (210) and (100) planes were more sensitive to decomposition than crystals shocked on the (111) plane. The possible sources of the observed anisotropy are discussed with regard to the inelastic deformation mechanisms of shocked RDX. Our results suggest that, despite the anisotropy observed for shock initiation, decomposition pathways for all three orientations are similar.

H-alpha images of the Cygnus Loop - A new look at shock-wave dynamics in an old supernova remnant

NASA Technical Reports Server (NTRS)

Fesen, Robert A.; Kwitter, Karen B.; Downes, Ronald A.

1992-01-01

Attention is given to deep H-alpha images of portions of the east, west, and southwest limbs of the Cygnus Loop which illustrate several aspects of shock dynamics in a multiphase interstellar medium. An H-alpha image of the isolated eastern shocked cloud reveals cloud deformation and gas stripping along the cloud's edges, shock front diffraction and reflection around the rear of the cloud, and interior remnant emission due to upstream shock reflection. A faint Balmer-dominated filament is identified 30 arcmin further west of the remnant's bright line of western radiative filaments. This detection indicates a far more westerly intercloud shock front position than previously realized, and resolves the nature of the weak X-ray, optical, and nonthermal radio emission observed west of NGC 6960. Strongly curved Balmer-dominated filaments along the remnant's west and southwest edge may indicate shock diffraction caused by shock wave passage in between clouds.

Optoheterodyne Doppler measurements of the ballistic expansion of the products of the shock wave-induced surface destruction: Experiment and theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andriyash, A. V.; Astashkin, M. V.; Baranov, V. K.

2016-06-15

The results of optoheterodyne Doppler measurements of the ballistic expansion of the products of surface destruction under shock-wave loading are presented. The possibility of determining the physical characteristics of a rapidly flying dust cloud, including the microparticle velocities, the microparticle sizes, and the areal density of the dust cloud, is shown. A compact stand for performing experiments on shock-wave loading of metallic samples is described. Shock-wave loading is performed by a 100-µm-thick tantalum flyer plate accelerated to a velocity of 2.8 km/s. As the samples, lead plates having various thicknesses and the same surface roughness are used. At a shock-wavemore » pressure of 31.5 GPa, the destruction products are solid microparticles about 50 µm in size. At a pressure of 42 and 88 GPa, a liquid-drop dust cloud with a particle size of 10–15 µm is formed. To interpret the spectral data on the optoheterodyne Doppler measurements of the expansion of the surface destruction products (spalled fragments, dust microparticles), a transport equation for the function of mutual coherence of a multiply scattered field is used. The Doppler spectra of a backscattered signal are calculated with the model developed for the dust cloud that appears when a shock wave reaches the sample surface at the parameters that are typical of an experimental situation. Qualitative changes are found in the spectra, depending on the optical thickness of the dust cloud. The obtained theoretical results are in agreement with the experimental data.« less

Shock Mitigating Seat Single Impact Program

DTIC Science & Technology

2014-04-24

new seats from Shockwave, SHOXS and Zodiac , were tested during the third and fourth phases of the final test program and these were conducted between...test program to the four single jockey style seats from Shockwave, SHOXS, Ullman and Zodiac because of budget and time constraints. The program...along with the Zodiac jockey pod seat that replaced the Ullman seat. 2711 (NETE CS) ZT4110-R 23 April 2014 QF035 32/39 Rev. 05/2011.11.14 69. The

Effectiveness of extracorporeal shockwave therapy in three major tendon diseases.

PubMed

Carulli, Christian; Tonelli, Filippo; Innocenti, Matteo; Gambardella, Bonaventura; Muncibì, Francesco; Innocenti, Massimo

2016-03-01

Extracorporeal shockwave therapy is a conservative treatment for several painful musculoskeletal disorders. The aim of the study was the assessment of the relief from pain by the shockwave therapy in a population of consecutive patients affected by specific pathologies. A group of consecutive patients were studied and treated. They were affected by calcific tendonitis of the shoulder (129 patients), chronic Achilles tendinopathy (102 patients), and lateral epicondylitis of the elbow (80 subjects). Each patient had 3 applications with a monthly interval, and was followed up at 1, 6, and 12 months after treatment. Results were evaluated by the numeric rating scale (NRS) in all cases, the Constant Murley Score for the assessment of the shoulder function, the American Orthopaedic Foot and Ankle Society Score for subjects affected by chronic Achilles tendinopathy, and the Oxford Elbow Score for those affected by a lateral epicondylitis of the elbow. One year after treatment, the results were considered satisfactory with an almost complete resolution of symptoms. There were statistically significant results at the 12-month follow-ups regarding the mean NRS score (from 6.25 to 0.2), the Constant Murley Score (from 66.7 to 79.4), the Oxford Elbow Score (from 28 to 46), and the AOFAS (from 71 to 86). Extracorporeal shockwave therapy may be considered a safe, economic, and effective treatment for several chronic musculoskeletal disorders, allowing satisfactory pain relief and improvement of function ability. Level IV.

Simulation of shock-induced bubble collapse with application to vascular injury in shockwave lithotripsy

NASA Astrophysics Data System (ADS)

Coralic, Vedran

Shockwave lithotripsy is a noninvasive medical procedure wherein shockwaves are repeatedly focused at the location of kidney stones in order to pulverize them. Stone comminution is thought to be the product of two mechanisms: the propagation of stress waves within the stone and cavitation erosion. However, the latter mechanism has also been implicated in vascular injury. In the present work, shock-induced bubble collapse is studied in order to understand the role that it might play in inducing vascular injury. A high-order accurate, shock- and interface-capturing numerical scheme is developed to simulate the three-dimensional collapse of the bubble in both the free-field and inside a vessel phantom. The primary contributions of the numerical study are the characterization of the shock-bubble and shock-bubble-vessel interactions across a large parameter space that includes clinical shockwave lithotripsy pressure amplitudes, problem geometry and tissue viscoelasticity, and the subsequent correlation of these interactions to vascular injury. Specifically, measurements of the vessel wall pressures and displacements, as well as the finite strains in the fluid surrounding the bubble, are utilized with available experiments in tissue to evaluate damage potential. Estimates are made of the smallest injurious bubbles in the microvasculature during both the collapse and jetting phases of the bubble's life cycle. The present results suggest that bubbles larger than one micrometer in diameter could rupture blood vessels under clinical SWL conditions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Janardhanraj, S.; Jagadeesh, G., E-mail: jaggie@aero.iisc.ernet.in

A novel concept to generate miniature shockwaves in a safe, repeatable, and controllable manner in laboratory confinements using an in situ oxyhydrogen generator has been proposed and demonstrated. This method proves to be more advantageous than existing methods because there is flexibility to vary strength of the shockwave, there is no need for storage of high pressure gases, and there is minimal waste disposal. The required amount of oxyhydrogen mixture is generated using alkaline electrolysis that produces hydrogen and oxygen gases in stoichiometric quantity. The rate of oxyhydrogen mixture production for the newly designed oxyhydrogen generator is found to bemore » around 8 ml/s experimentally. The oxyhydrogen generator is connected to the driver section of a specially designed 10 mm square miniature shock tube assembly. A numerical code that uses CANTERA software package is used to predict the properties of the driver gas in the miniature shock tube. This prediction along with the 1-D shock tube theory is used to calculate the properties of the generated shockwave and matches reasonably well with the experimentally obtained values for oxyhydrogen mixture fill pressures less than 2.5 bars. The miniature shock tube employs a modified tri-clover clamp assembly to facilitate quick changing of diaphragm and replaces the more cumbersome nut and bolt system of fastening components. The versatile nature of oxyhydrogen detonation-driven miniature shock tube opens up new horizons for shockwave-assisted interdisciplinary applications.« less

Efficacy of the Duet lithotripter using two energy sources for stone fragmentation by shockwaves: an in vitro study.

PubMed

Greenstein, Alexander; Sofer, Mario; Matzkin, Haim

2004-12-01

To evaluate the efficacy of the Duet lithotripter's novel design of two independent spark-plug generator/reflector systems focused at a common F2. The apparatus allows either simultaneous delivery of shockwaves from both generators (resulting in a per-shock energy delivery at F2 equal to that delivered by its single generator at about 24 kV), alternating (between the two generators), or single-generator delivery of shockwaves at various energy levels and rates. Eighty-five phantom gypsum stones (volume 786 mm3 each) were placed in a net-like basket and immersed in a specially designed waterbath coupled with the Duet lithotripter (Direx Medical Systems Ltd., Petach Tikva, Israel). Shockwaves were delivered at rates of either 60 or 120 per minute and at intensities of 16 or 22.8 kV (electrohydraulic). Energy was delivered either separately from each generator, in an alternating mode, or simultaneously from both generators. The number of shocks required to fragment the stones sufficiently to allow all of the pieces to fall through the basket holes (complete fragmentation) was recorded. The number of shocks required for complete fragmentation in the alternate mode (120 shocks/min, each generator rate 60/min; 22.8kV) was lower than with the single generator, 112 +/- 19 v 134 +/- 18 (at a rate of 120/min; 22.8 kV). The simultaneous mode of dual generator shockwave delivery was more effective than the traditional single generator (114 +/- 28 shocks at a rate of 120/min, 16 kV v 159 +/- 40 shocks at a rate 120/min; 22.8kV). The Duet lithotripter is more effective when used in a simultaneous or alternating mode than is the classical single mode of shock delivery, with the added benefit of shorter treatment time.

Plantar fascia-specific stretching versus radial shock-wave therapy as initial treatment of plantar fasciopathy.

PubMed

Rompe, Jan D; Cacchio, Angelo; Weil, Lowell; Furia, John P; Haist, Joachim; Reiners, Volker; Schmitz, Christoph; Maffulli, Nicola

2010-11-03

Whether plantar fascia-specific stretching or shock-wave therapy is effective as an initial treatment for proximal plantar fasciopathy remains unclear. The aim of this study was to test the null hypothesis of no difference in the effectiveness of these two forms of treatment for patients who had unilateral plantar fasciopathy for a maximum duration of six weeks and which had not been treated previously. One hundred and two patients with acute plantar fasciopathy were randomly assigned to perform an eight-week plantar fascia-specific stretching program (Group I, n = 54) or to receive repetitive low-energy radial shock-wave therapy without local anesthesia, administered weekly for three weeks (Group II, n = 48). All patients completed the seven-item pain subscale of the validated Foot Function Index and a patient-relevant outcome questionnaire. Patients were evaluated at baseline and at two, four, and fifteen months after baseline. The primary outcome measures were a mean change in the Foot Function Index sum score at two months after baseline, a mean change in item 2 (pain during the first few steps of walking in the morning) on this index, and satisfaction with treatment. No difference in mean age, sex, weight, or duration of symptoms was found between the groups at baseline. At two months after baseline, the Foot Function Index sum score showed significantly greater changes for the patients managed with plantar fascia-specific stretching than for those managed with shock-wave therapy (p < 0.001), as well as individually for item 2 (p = 0.002). Thirty-five patients (65%) in Group I versus fourteen patients (29%) in Group II were satisfied with the treatment (p < 0.001). These findings persisted at four months. At fifteen months after baseline, no significant between-group difference was measured. A program of manual stretching exercises specific to the plantar fascia is superior to repetitive low-energy radial shock-wave therapy for the treatment of acute symptoms of proximal plantar fasciopathy.

Strong anti-gravity Life in the shock wave

NASA Astrophysics Data System (ADS)

Fabbrichesi, Marco; Roland, Kaj

1992-12-01

Strong anti-gravity is the vanishing of the net force between two massive particles at rest, to all orders in Newton's constant. We study this phenomenon and show that it occurs in any effective theory of gravity which is obtained from a higher-dimensional model by compactification on a manifold with flat directions. We find the exact solution of the Einstein equations in the presence of a point-like source of strong anti-gravity by dimensional reduction of a shock-wave solution in the higher-dimensional model.

Molecular-level Analysis of Shock-wave Physics and Derivation of the Hugoniot Relations for Soda-lime Glass

DTIC Science & Technology

2011-06-17

based glasses like fused silica and soda - lime glass , the polyhedral central cation is silicon. In this case, each silicon is surrounded by four oxygen...to two network forming cations) oxygen atoms per network polyhedron. The equilibrium values for this parameter in fused silica and soda - lime glass ...Molecular-level analysis of shock-wave physics and derivation of the Hugoniot relations for soda - lime glass M. Grujicic • B. Pandurangan • W. C. Bell

Investigation of supersonic jets shock-wave structure

NASA Astrophysics Data System (ADS)

Zapryagaev, V. I.; Gubanov, D. A.; Kavun, I. N.; Kiselev, N. P.; Kundasev, S. G.; Pivovarov, A. A.

2017-10-01

The paper presents an experimental studies overview of the free supersonic jet flow structure Ma = 1.0, Npr = 5, exhausting from a convergent profiled nozzle into a ambient space. Also was observed the jets in the presence of artificial streamwise vortices created by chevrons and microjets located on the nozzle exit. The technique of experimental investigation, schlieren-photographs and schemes of supersonic jets, and Pitot pressure distributions, are presented. A significant effect of vortex generators on the shock-wave structure of the flow is shown.

Modelling of the internal dynamics and density in a tens of joules plasma focus device

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marquez, Ariel; Gonzalez, Jose; Tarifeno-Saldivia, Ariel

2012-01-15

Using MHD theory, coupled differential equations were generated using a lumped parameter model to describe the internal behaviour of the pinch compression phase in plasma focus discharges. In order to provide these equations with appropriate initial conditions, the modelling of previous phases was included by describing the plasma sheath as planar shockwaves. The equations were solved numerically, and the results were contrasted against experimental measurements performed on the device PF-50J. The model is able to predict satisfactorily the timing and the radial electron density profile at the maximum compression.

Effect of Shock Waves on Dielectric Properties of KDP Crystal

NASA Astrophysics Data System (ADS)

Sivakumar, A.; Suresh, S.; Pradeep, J. Anto; Balachandar, S.; Martin Britto Dhas, S. A.

2018-05-01

An alternative non-destructive approach is proposed and demonstrated for modifying electrical properties of crystal using shock-waves. The method alters dielectric properties of a potassium dihydrogen phosphate (KDP) crystal by loading shock-waves generated by a table-top shock tube. The experiment involves launching the shock-waves perpendicular to the (100) plane of the crystal using a pressure driven table-top shock tube with Mach number 1.9. Electrical properties of dielectric constant, dielectric loss, permittivity, impedance, AC conductivity, DC conductivity and capacitance as a function of spectrum of frequency from 1 Hz to 1 MHz are reported for both pre- and post-shock wave loaded conditions of the KDP crystal. The experimental results reveal that dielectric constant of KDP crystal is sensitive to the shock waves such that the value decreases for the shock-loaded KDP sample from 158 to 147. The advantage of the proposed approach is that it is an alternative to the conventional doping process for tailoring dielectric properties of this type of crystal.

Explosion-Induced Implosions of Cylindrical Shell Structures

NASA Astrophysics Data System (ADS)

Ikeda, C. M.; Duncan, J. H.

2010-11-01

An experimental study of the explosion-induced implosion of cylindrical shell structures in a high-pressure water environment was performed. The shell structures are filled with air at atmospheric pressure and are placed in a large water-filled pressure vessel. The vessel is then pressurized to various levels P∞=αPc, where Pc is the natural implosion pressure of the model and α is a factor that ranges from 0.1 to 0.9. An explosive is then set off at various standoff distances, d, from the model center line, where d varies from R to 10R and R is the maximum radius of the explosion bubble. High-speed photography (27,000 fps) was used to observe the explosion and resulting shell structure implosion. High-frequency underwater blast sensors recorded dynamic pressure waves at 6 positions. The cylindrical models were made from aluminum (diameter D = 39.1 mm, wall thickness t = 0.89 mm, length L = 240 mm) and brass (D = 16.7 mm, t = 0.36 mm, L=152 mm) tubes. The pressure records are interpreted in light of the high-speed movies. It is found that the implosion is induced by two mechanisms: the shockwave generated by the explosion and the jet formed during the explosion-bubble collapse. Whether an implosion is caused by the shockwave or the jet depends on the maximum bubble diameter and the standoff distance.

Origin of three-dimensional shapes of chondrules. I. Hydrodynamics simulations of rotating droplet exposed to high-velocity rarefied gas flow

NASA Astrophysics Data System (ADS)

Miura, Hitoshi; Nakamoto, Taishi; Doi, Masao

2008-09-01

The origin of three-dimensional shapes of chondrules is an important information to identify their formation mechanism in the early solar nebula. The measurement of their shapes by using X-ray computed topography suggested that they are usually close to perfect spheres, however, some of them have rugby-ball-like (prolate) shapes [Tsuchiyama, A., Shigeyoshi, R., Kawabata, T., Nakano, T., Uesugi, K., Shirono, S., 2003. Lunar Planet. Sci. 34, 1271-1272]. We considered that the prolate shapes reflect the deformations of chondrule precursor dust particles when they are heated and melted in the high velocity gas flow. In order to reveal the origin of chondrule shapes, we carried out the three-dimensional hydrodynamics simulations of a rotating molten chondrule exposed to the gas flow in the framework of the shock-wave heating model for chondrule formation. We adopted the gas ram pressure acting on the chondrule surface of p=10 dyncm in a typical shock wave. Considering that the chondrule precursor dust particle has an irregular shape before melting, the ram pressure causes a net torque to rotate the particle. The estimated angular velocity is ω=140 rads for the precursor radius of r=1 mm, though it has a different value depending on the irregularity of the shape. In addition, the rotation axis is likely to be perpendicular to the direction of the gas flow. Our calculations showed that the rotating molten chondrule elongates along the rotation axis, in contrast, shrinks perpendicularly to it. It is a prolate shape. The reason why the molten chondrule is deformed to a prolate shape was clearly discussed. Our study gives a complementary constraint for chondrule formation mechanisms, comparing with conventional chemical analyses and dynamic crystallization experiments that have mainly constrained the thermal evolutions of chondrules.

Unifying role of dissipative action in the dynamic failure of solids

NASA Astrophysics Data System (ADS)

Grady, Dennis E.

2015-04-01

A fourth-power law underlying the steady shock-wave structure and solid viscosity of condensed material has been observed for a wide range of metals and non-metals. The fourth-power law relates the steady-wave Hugoniot pressure to the fourth power of the strain rate during passage of the material through the structured shock wave. Preceding the fourth-power law was the observation in a shock transition that the product of the shock dissipation energy and the shock transition time is a constant independent of the shock pressure amplitude. Invariance of this energy-time product implies the fourth-power law. This property of the shock transition in solids was initially identified as a shock invariant. More recently, it has been referred to as the dissipative action, although no relationship to the accepted definitions of action in mechanics has been demonstrated. This same invariant property has application to a wider range of transient failure phenomena in solids. Invariance of this dissipation action has application to spall fracture, failure through adiabatic shear, shock compaction of granular media, and perhaps others. Through models of the failure processes, a clearer picture of the physics underlying the observed invariance is emerging. These insights in turn are leading to a better understanding of the shock deformation processes underlying the fourth-power law. Experimental result and material models encompassing the dynamic failure of solids are explored for the purpose of demonstrating commonalities leading to invariance of the dissipation action. Calculations are extended to aluminum and uranium metals with the intent of predicting micro-scale dynamics and spatial structure in the steady shock wave.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grady, Dennis E.

A fourth-power law underlying the steady shock-wave structure and solid viscosity of condensed material has been observed for a wide range of metals and non-metals. The fourth-power law relates the steady-wave Hugoniot pressure to the fourth power of the strain rate during passage of the material through the structured shock wave. Preceding the fourth-power law was the observation in a shock transition that the product of the shock dissipation energy and the shock transition time is a constant independent of the shock pressure amplitude. Invariance of this energy-time product implies the fourth-power law. This property of the shock transition inmore » solids was initially identified as a shock invariant. More recently, it has been referred to as the dissipative action, although no relationship to the accepted definitions of action in mechanics has been demonstrated. This same invariant property has application to a wider range of transient failure phenomena in solids. Invariance of this dissipation action has application to spall fracture, failure through adiabatic shear, shock compaction of granular media, and perhaps others. Through models of the failure processes, a clearer picture of the physics underlying the observed invariance is emerging. These insights in turn are leading to a better understanding of the shock deformation processes underlying the fourth-power law. Experimental result and material models encompassing the dynamic failure of solids are explored for the purpose of demonstrating commonalities leading to invariance of the dissipation action. Calculations are extended to aluminum and uranium metals with the intent of predicting micro-scale dynamics and spatial structure in the steady shock wave.« less

Bubble Proliferation or Dissolution of Cavitation Nuclei in the Beam Path of a Shock-Wave Lithotripter

NASA Astrophysics Data System (ADS)

Frank, Spencer; Lautz, Jaclyn; Sankin, Georgy N.; Szeri, Andrew J.; Zhong, Pei

2015-03-01

It is hypothesized that the decreased treatment efficiency in contemporary shock-wave lithotripters is related to tensile wave attenuation due to cavitation in the prefocal beam path. Utilizing high-speed imaging of the beam path and focal pressure waveform measurements, tensile attenuation is associated with bubble proliferation. By systematically testing different combinations of pulse-repetition frequency and gas concentration, we modulate the bubble-dissolution time to identify which conditions lead to bubble proliferation and show that reducing bubble proliferation in the beam path significantly improves acoustic transmission and stone comminution efficiency in vitro. In addition to experiments, a bubble-proliferation model is developed that takes gas diffusion across the bubble wall and bubble fragmentation into account. By aligning the model with experimental observations, the number of daughter bubbles produced after a single lithotripter bubble collapse is estimated to be in the range of 253 ˜510 . This finding is on the same order of magnitude with previous measurements of an isolated bubble collapse in a lithotripter field by Pishchalnikov, McAteer, and Williams [BJU Int. 102, 1681 (2008), 10.1111/j.1464-410X.2008.07896.x], and this estimate improves the general understanding of lithotripsy bubble dynamics in the beam path.

Tension of Liquids by Shockwaves

NASA Astrophysics Data System (ADS)

Utkin, A. V.; Sosikov, V. A.

2009-12-01

Experimental investigations of dynamic tension of liquids (water, ethanol, glycerol, hexane, hexadecane, pentadecane, and transformer oil) under shock waves have been made. The method of spall strength measurements was applied and wave profiles were registered by laser interferometer VISAR. It was found that negative pressures in liquids were almost independent from the value of stain rate when the temperature was far from melting point. But near the melting point the spall strength of water, hexadecane, pentadecane, and glycerol is a strong function of strain rate and shock-wave amplitude. The process of cavitation in hexadecane and methanol is double-staged. At the first stage formation of cavities starts, and a kinked of free velocity profile is observed. At the second stage the cavity growth rate increases and the spall-pulse occurs. The theory of homogeneous bubble nucleation was used to explain the experimental results. It was observed for water that spall-pulse amplitude may be higher than the shock wave amplitude. To explain this phenomenon the model of failure kinetics, taking into account the inertial bubbles growth, has been proposed.

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

NASA Technical Reports Server (NTRS)

Dudek, Julianne C.; Carlson, Jan-Renee

2017-01-01

Full seven-equation Reynolds stress turbulence models are a relatively new and promising tool for todays aerospace technology challenges. This paper uses two stress-omega full Reynolds stress models to evaluate challenging flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSGLRR full second-moment Reynolds stress models are evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST) two-equation models.

Observational clues to the energy release process in impulsive solar bursts

NASA Technical Reports Server (NTRS)

Batchelor, David

1990-01-01

The nature of the energy release process that produces impulsive bursts of hard X-rays and microwaves during solar flares is discussed, based on new evidence obtained using the method of Crannell et al. (1978). It is shown that the hard X-ray spectral index gamma is negatively correlated with the microwave peak frequency, suggesting a common source for the microwaves and X-rays. The thermal and nonthermal models are compared. It is found that the most straightforward explanations for burst time behavior are shock-wave particle acceleration in the nonthermal model and thermal conduction fronts in the thermal model.

Shockwave therapy for the treatment of chronic proximal hamstring tendinopathy in professional athletes.

PubMed

Cacchio, Angelo; Rompe, Jan D; Furia, John P; Susi, Piero; Santilli, Valter; De Paulis, Fosco

2011-01-01

Chronic proximal hamstring tendinopathy is an overuse syndrome that is usually managed by nonoperative methods. Shockwave therapy has proved to be effective in many tendinopathies. Shockwave therapy may be more effective than other nonoperative treatments for chronic proximal hamstring tendinopathy. Randomized controlled clinical study; Level of evidence, 1. Forty professional athletes with chronic proximal hamstring tendinopathy were enrolled between February 1, 2004, and September 30, 2006. Patients were randomly assigned to receive either shockwave therapy, consisting of 2500 impulses per session at a 0.18 mJ/mm² energy flux density without anesthesia, for 4 weeks (SWT group, n = 20), or traditional conservative treatment consisting of nonsteroidal anti-inflammatory drugs, physiotherapy, and an exercise program for hamstring muscles (TCT group, n = 20). Patients were evaluated before treatment, and 1 week and 3, 6, and 12 months after the end of treatment. The visual analog scale (VAS) score for pain and Nirschl phase rating scale (NPRS) were used as primary outcome measures. The patients were observed for a mean of 10.7 months (range, 1-12 months). Six patients were lost to follow-up because they underwent a surgical intervention: 3 (all in TCT group) were lost at 3 months; 2 (1 in each group), at 6 months; and 1 (in the TCT group), at 12 months. Primary follow-up was at 3 months after the beginning of treatment. The VAS scores in the SWT and TCT groups were 7 points before treatment (P = .84), and 2 points and 5 points, respectively, 3 months after treatment (P < .001). The NPRS scores in the SWT and TCT groups were 5 points in either group before treatment (P = .48), and 2 points and 6 points, respectively, 3 months after treatment (P < .001). At 3 months after treatment, 17 of the 20 patients (85%) in the SWT group and 2 of the 20 patients (10%) in the TCT group achieved a reduction of at least 50% in pain (P < .001). There were no serious complications in the SWT group. Shockwave therapy is a safe and effective treatment for patients with chronic proximal hamstring tendinopathy.

Optical nucleation of bubble clouds in a high pressure spherical resonator.

PubMed

Anderson, Phillip; Sampathkumar, A; Murray, Todd W; Gaitan, D Felipe; Glynn Holt, R

2011-11-01

An experimental setup for nucleating clouds of bubbles in a high-pressure spherical resonator is described. Using nanosecond laser pulses and multiple phase gratings, bubble clouds are optically nucleated in an acoustic field. Dynamics of the clouds are captured using a high-speed CCD camera. The images reveal cloud nucleation, growth, and collapse and the resulting emission of radially expanding shockwaves. These shockwaves are reflected at the interior surface of the resonator and then reconverge to the center of the resonator. As the shocks reconverge upon the center of the resonator, they renucleate and grow the bubble cloud. This process is repeated over many acoustic cycles and with each successive shock reconvergence, the bubble cloud becomes more organized and centralized so that subsequent collapses give rise to stronger, better defined shockwaves. After many acoustic cycles individual bubbles cannot be distinguished and the cloud is then referred to as a cluster. Sustainability of the process is ultimately limited by the detuning of the acoustic field inside the resonator. The nucleation parameter space is studied in terms of laser firing phase, laser energy, and acoustic power used.

Developing a laser shockwave model for characterizing diffusion bonded interfaces

NASA Astrophysics Data System (ADS)

Lacy, Jeffrey M.; Smith, James A.; Rabin, Barry H.

2015-03-01

The US National Nuclear Security Agency has a Global Threat Reduction Initiative (GTRI) with the goal of reducing the worldwide use of high-enriched uranium (HEU). A salient component of that initiative is the conversion of research reactors from HEU to low enriched uranium (LEU) fuels. An innovative fuel is being developed to replace HEU in high-power research reactors. The new LEU fuel is a monolithic fuel made from a U-Mo alloy foil encapsulated in Al-6061 cladding. In order to support the fuel qualification process, the Laser Shockwave Technique (LST) is being developed to characterize the clad-clad and fuel-clad interface strengths in fresh and irradiated fuel plates. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves to characterize interfaces in nuclear fuel plates. However, because the deposition of laser energy into the containment layer on a specimen's surface is intractably complex, the shock wave energy is inferred from the surface velocity measured on the backside of the fuel plate and the depth of the impression left on the surface by the high pressure plasma pulse created by the shock laser. To help quantify the stresses generated at the interfaces, a finite element method (FEM) model is being utilized. This paper will report on initial efforts to develop and validate the model by comparing numerical and experimental results for back surface velocities and front surface depressions in a single aluminum plate representative of the fuel cladding.

Interferometric data for a shock-wave/boundary-layer interaction

NASA Technical Reports Server (NTRS)

Dunagan, Stephen E.; Brown, James L.; Miles, John B.

1986-01-01

An experimental study of the axisymmetric shock-wave / boundary-layer strong interaction flow generated in the vicinity of a cylinder-cone intersection was conducted. The study data are useful in the documentation and understanding of compressible turbulent strong interaction flows, and are part of a more general effort to improve turbulence modeling for compressible two- and three-dimensional strong viscous/inviscid interactions. The nominal free stream Mach number was 2.85. Tunnel total pressures of 1.7 and 3.4 atm provided Reynolds number values of 18 x 10(6) and 36 x 10(6) based on model length. Three cone angles were studied giving negligible, incipient, and large scale flow separation. The initial cylinder boundary layer upstream of the interaction had a thickness of 1.0 cm. The subsonic layer of the cylinder boundary layer was quite thin, and in all cases, the shock wave penetrated a significant portion of the boundary layer. Owing to the thickness of the cylinder boundary layer, considerable structural detail was resolved for the three shock-wave / boundary-layer interaction cases considered. The primary emphasis was on the application of the holographic interferometry technique. The density field was deduced from an interferometric analysis based on the Able transform. Supporting data were obtained using a 2-D laser velocimeter, as well as mean wall pressure and oil flow measurements. The attached flow case was observed to be steady, while the separated cases exhibited shock unsteadiness. Comparisons with Navier-Stokes computations using a two-equation turbulence model are presented.

Measurements of a Strength of Metals in a Picosecond Time Range

NASA Astrophysics Data System (ADS)

Ashitkov, Sergey; Komarov, Pavel; Agranat, Mikhail; Kanel, Gennady; Fortov, Vladimir

2013-06-01

We studied the shock-wave phenomena in metal films of a micron or submicron thickness irradiated by femtosecond laser pulses. The single-shot interferometer technique was used to record the time and spatial resolved displacements of both the frontal and rear surfaces of the films. The free surface displacement histories were converted into the free surface velocity histories using several various approaches. As a result, new data on the HEL and spall strength values have been obtained for aluminum, iron, nickel and other metals in strongly metastable states close to ultimate shear and tensile stresses. Comparison of measured parameters of elastic shock waves with the data of plate impact experiments at larger sample thicknesses demonstrate different regimes of the decay: whereas for pure fcc metals the decay may be described by one power function over 1 μm to 10 mm range of the distances, in the case of bcc iron main decay occurs obviously at the distance of order of 50 μm. The data are discussed from the view point of main mechanisms of high-rate deformation and fracture.

Unstable 3D phenomena: Dynamic interactions of a cavitation bubble and Richtmyer-Meshkov unstable divot

NASA Astrophysics Data System (ADS)

Buttler, William; Renner, Dru; Morris, Chris; Manzanares, Ruben; Heidemann, Joel; Kalas, Ryan; Llobet, Anna; Martinez, John; Payton, Jeremy; Saunders, Andy; Schmidt, Derek; Tainter, Amy; Vincent, Samuel; Vogan-McNeil, Wendy

2017-06-01

We radiographically explore a shock-induced Sn cavitation bubble as it interacts with a transverse cavitation wave caused by a Richtmyer-Meshkov unstable spike from a divot. The cavitation bubble forms as two shockwaves collide under the divot, as the shockwaves release to ambient pressure at the surface. The divot inverts and unstably grows, as expected and predicted, but the release waves that form the cavitation bubble reflect from and constrain the cavitation wave growth. As the cavitation wave grows it pierces the cavitation bubble, deflating it onto the unstable transverse cavitation wave.

Ejection of Particles from the Free Surface of Shock-Loaded Lead into Vacuum and Gas Medium

NASA Astrophysics Data System (ADS)

Ogorodnikov, V. A.; Mikhailov, A. L.; Erunov, S. V.; Antipov, M. V.; Fedorov, A. V.; Syrunin, M. A.; Kulakov, E. V.; Kleshchevnikov, O. A.; Yurtov, I. V.; Utenkov, A. A.; Finyushin, S. A.; Chudakov, E. A.; Kalashnikov, D. A.; Pupkov, A. S.; Chapaev, A. V.; Mishanov, A. V.; Glushikhin, V. V.; Fedoseev, A. V.; Tagirov, R. R.; Kostyukov, S. A.; Tagirova, I. Yu.; Saprykina, E. V.

2017-12-01

The presence and behavior of a gas-metal interfacial layer at the free surface of shock-wave driven flying vehicles in gases of various compositions and densities has not been sufficiently studied so far. We present new comparative data on "dusting" from the free surface of lead into vacuum and gas as dependent on the surface roughness, pressure amplitude at the shock-wave front, and phase state of the material. Methods of estimating the mass flux of ejected particles in the presence of a gas medium at the free metal surface are proposed.

Discrete mathematical physics and particle modeling

NASA Astrophysics Data System (ADS)

Greenspan, D.

The theory and application of the arithmetic approach to the foundations of both Newtonian and special relativistic mechanics are explored. Using only arithmetic, a reformulation of the Newtonian approach is given for: gravity; particle modeling of solids, liquids, and gases; conservative modeling of laminar and turbulent fluid flow, heat conduction, and elastic vibration; and nonconservative modeling of heat convection, shock-wave generation, the liquid drop problem, porous flow, the interface motion of a melting solid, soap films, string vibrations, and solitons. An arithmetic reformulation of special relativistic mechanics is given for theory in one space dimension, relativistic harmonic oscillation, and theory in three space dimensions. A speculative quantum mechanical model of vibrations in the water molecule is also discussed.

Molecular-Level Analysis of Shock-Wave Physics and Derivation of the Hugoniot Relations for Fused Silica

DTIC Science & Technology

2012-06-01

product manufacturing are associated with relatively low costs; and ( c ) ballistic and blast impact survivability of ceramic glasses can be substantially...19a. NAME OF RESPONSIBLE PERSON a. REPORT unclassified b. ABSTRACT unclassified c . THIS PAGE unclassified Standard Form 298 (Rev. 8-98...b) continuum-material approximations (Ref 5–7, 15–18); and ( c ) meso-length scale models based on explicit representation of cracks (Ref 19, 20

The effect of antibacterial acting extracorporeal shockwaves on bacterial cell integrity.

PubMed

Horn, Carsten; Mengele, Karin; Gerdesmeyer, Ludger; Gradinger, Reiner; Gollwitzer, Hans

2009-12-01

Antibacterial effects of extracorporeal shockwaves (ESWs) have been demonstrated in vitro against bacteria under static and dynamic growth conditions. This study assessed the effects of ESWs on the cell wall integrity of bacteria. Standardized suspensions of Staphylococcus aureus were exposed to various shockwave impulses (2000-12,000) of different energy flux densities (EFD, 0.38-0.96 mJ/mm(2)). Bacterial suspensions of equal concentration that had been permeabilized (to >99%) with isopropanol were used as positive controls. The bacteria of all groups were stained with Sytox Green nucleic acid stain. The fluorescence of the shockwave-treated, permeabilized, and untreated suspensions was measured and compared for bacterial survival, quantified by colony-forming units after plating. Although ESWs showed a significant energy-dependent antibacterial effect that reduced CFUs in the treated suspensions by between 56% and 99%, only maximum energies (4000 impulses at 0.96 mJ/mm(2) and 12,000 impulses at 0.59 mJ/mm(2)) were followed by a significant increase in fluorescence compared with the untreated control (p<0.05). However, the fluorescence of these treated groups was still far less than that of the alcohol-permeabilized positive control groups (p<0.05). Lower energies and impulse rates did not show increased intracellular uptake of the fluorescent dye (p>0.05). This is the first study to assess bacterial cell wall permeability after ESW treatment. It was found that the permeabilization of bacterial cells after ESW treatment was far less than expected due to the corresponding antibacterial effect. Other mechanisms, such as intracellular effects, might be involved in bacterial killing after ESWs and still must be elucidated.

Clinical Nomograms to Predict Stone-Free Rates after Shock-Wave Lithotripsy: Development and Internal-Validation

PubMed Central

Kim, Jung Kwon; Ha, Seung Beom; Jeon, Chan Hoo; Oh, Jong Jin; Cho, Sung Yong; Oh, Seung-June; Kim, Hyeon Hoe; Jeong, Chang Wook

2016-01-01

Purpose Shock-wave lithotripsy (SWL) is accepted as the first line treatment modality for uncomplicated upper urinary tract stones; however, validated prediction models with regards to stone-free rates (SFRs) are still needed. We aimed to develop nomograms predicting SFRs after the first and within the third session of SWL. Computed tomography (CT) information was also modeled for constructing nomograms. Materials and Methods From March 2006 to December 2013, 3028 patients were treated with SWL for ureter and renal stones at our three tertiary institutions. Four cohorts were constructed: Total-development, Total-validation, CT-development, and CT-validation cohorts. The nomograms were developed using multivariate logistic regression models with selected significant variables in a univariate logistic regression model. A C-index was used to assess the discrimination accuracy of nomograms and calibration plots were used to analyze the consistency of prediction. Results The SFR, after the first and within the third session, was 48.3% and 68.8%, respectively. Significant variables were sex, stone location, stone number, and maximal stone diameter in the Total-development cohort, and mean Hounsfield unit (HU) and grade of hydronephrosis (HN) were additional parameters in the CT-development cohort. The C-indices were 0.712 and 0.723 for after the first and within the third session of SWL in the Total-development cohort, and 0.755 and 0.756, in the CT-development cohort, respectively. The calibration plots showed good correspondences. Conclusions We constructed and validated nomograms to predict SFR after SWL. To the best of our knowledge, these are the first graphical nomograms to be modeled with CT information. These may be useful for patient counseling and treatment decision-making. PMID:26890006

Comparison of hydrodynamic simulations with two-shockwave drive target experiments

NASA Astrophysics Data System (ADS)

Karkhanis, Varad; Ramaprabhu, Praveen; Buttler, William

2015-11-01

We consider hydrodynamic continuum simulations to mimic ejecta generation in two-shockwave target experiments, where metallic surface is loaded by two successive shock waves. Time of second shock in simulations is determined to match experimental amplitudes at the arrival of the second shock. The negative Atwood number A --> - 1 of ejecta simulations leads to two successive phase inversions of the interface corresponding to the passage of the shocks from heavy to light media in each instance. Metallic phase of ejecta (solid/liquid) depends on shock loading pressure in the experiment, and we find that hydrodynamic simulations quantify the liquid phase ejecta physics with a fair degree of accuracy, where RM instability is not suppressed by the strength effect. In particular, we find that our results of free surface velocity, maximum ejecta velocity, and maximum ejecta areal density are in excellent agreement with their experimental counterparts, as well as ejecta models. We also comment on the parametric space for hydrodynamic simulations in which they can be used to compare with the target experiments. This work was supported in part by the (U.S.) Department of Energy (DOE) under Contract No. DE-AC52-06NA2-5396.

Optical distortion in the field of a lithotripter shock wave

NASA Astrophysics Data System (ADS)

Carnell, M. T.; Emmony, D. C.

1995-10-01

The schlieren observation of cavitation phenomena produced in the tail of a lithotripter shock wave has indicated the presence of some interesting features. The images produced appear to indicate that cavitation transients in the field of a shock wave propagate nonsymmetrically; this is not the case. The apparent lack of symmetry exhibited by the primary cavitation transients is due to a complex optical lensing effect, which is brought about by the change in refractive index associated with the pressure profile of the shock wave. Objects seen through or immersed in the shock-wave field of an electromagnetic acoustic transducer, such as cavitation, appear highly distorted because of the strong positive and negative lensing effects of the compression and rarefaction cycles of the shock wave. A modification of the schlieren technique called the scale method has been used to model the distortion introduced by the shock wave and consequently explain the cavitation distortion. The technique has also been used to quantitatively analyze and partially reconstruct the lithotripter shock wave. The combination of schlieren and scale imaging gives more information about the refractive index field and therefore the shock-wave structure itself.

Interpretation of OAO-2 ultraviolet light curves of beta Doradus

NASA Technical Reports Server (NTRS)

Hutchinson, J. L.; Lillie, C. F.; Hill, S. J.

1975-01-01

Middle-ultraviolet light curves of beta Doradus, obtained by OAO-2, are presented along with other evidence indicating that the small additional bumps observed on the rising branches of these curves have their origin in shock-wave phenomena in the upper atmosphere of this classical Cepheid. A simple piston-driven spherical hydrodynamic model of the atmosphere is developed to explain the bumps, and the calculations are compared with observations. The model is found to be consistent with the shapes of the light curves as well as with measurements of the H-alpha radial velocities.

Experimental model of the role of cracks in the mechanism of explosive eruption of St. Helens-80

NASA Astrophysics Data System (ADS)

Kedrinskii, V. K.; Skulkin, A. A.

2017-07-01

A unique mini model of explosive volcano eruption through a formed system of cracks is developed. The process of crack formation and development is simulated by electric explosion of a conductor in a plate of optically transparent organic glass submerged into water. The explosion of a wire aligned with a through hole in the plate generates shock-wave loading along the plate and forms cracks. The fundamental role of high velocity flow in crack wedging by a high power hydrodynamic flow of a pulsating explosion cavity has been demonstrated.

Optodynamic characterization of shock waves after laser-induced breakdown in water.

PubMed

Petkovsek, Rok; Mozina, Janez; Mocnik, Grisa

2005-05-30

Plasma and a cavitation bubble develop at the site of laser-induced breakdown in water. Their formation and the propagation of the shock wave were monitored by a beam-deflection probe and an arm-compensated interferometer. The interferometer part of the setup was used to determine the relative position of the laser-induced breakdown. The time-of-flight data from the breakdown site to the probe beam yielded the velocity, and from the velocity the shock-wave pressure amplitudes were calculated. Two regions were found where the pressure decays with different exponents, pointing to a strong attenuation mechanism in the initial phase of the shock-wave propagation.

Well-posed two-temperature constitutive equations for stable dense fluid shock waves using molecular dynamics and generalizations of Navier-Stokes-Fourier continuum mechanics.

PubMed

Hoover, Wm G; Hoover, Carol G

2010-04-01

Guided by molecular dynamics simulations, we generalize the Navier-Stokes-Fourier constitutive equations and the continuum motion equations to include both transverse and longitudinal temperatures. To do so we partition the contributions of the heat transfer, the work done, and the heat flux vector between the longitudinal and transverse temperatures. With shockwave boundary conditions time-dependent solutions of these equations converge to give stationary shockwave profiles. The profiles include anisotropic temperature and can be fitted to molecular dynamics results, demonstrating the utility and simplicity of a two-temperature description of far-from-equilibrium states.

Microgravity Experiment: The Fate of Confined Shock Waves

NASA Astrophysics Data System (ADS)

Kobel, P.; Obreschkow, D.; Dorsaz, N.; de Bosset, A.; Farhat, M.

2007-11-01

Shockwave induced cavitation is a form of hydrodynamic cavitation generated by the interaction of shock waves with vapor nuclei and microscopic impurities. Both the shock waves and the induced cavitation are known as sources of erosion damage in hydraulic industrial systems and hence represent an important research topic in fluid dynamics. Here we present the first investigation of shock wave induced cavitation inside closed and isolated liquid volumes, which confine the shock wave by reflections and thereby promise a particularly strong coupling with cavitation. A microgravity platform (ESA, 42^nd parabolic flight campaign) was used to produce stable water drops with centimetric diameters. Inside these drops, a fast electrical discharge was generated to release a strong shock wave. This setting results in an amplified form of shockwave induced cavitation, visible in high-speed images as a transient haze of sub-millimetric bubbles synchronized with the shockwave radiation. A comparison between high-speed visualizations and 3D simulations of a shock front inside a liquid sphere reveals that focus zones within the drop lead to a significantly increased density of induced cavitation. Considering shock wave crossing and focusing may hence prove crucially useful to understand the important process of cavitation erosion.

Radial shock wave treatment alone is less efficient than radial shock wave treatment combined with tissue-specific plantar fascia-stretching in patients with chronic plantar heel pain.

PubMed

Rompe, Jan D; Furia, John; Cacchio, Angelo; Schmitz, Christoph; Maffulli, Nicola

2015-12-01

Whether shock wave therapy or shock wave therapy combined with plantar fascia-specific stretching is more efficient in treating chronic plantar heel pain remains unclear. The aim of the study was to test the null hypothesis of no difference of these two forms of management for patients who had unilateral plantar fasciopathy for a minimum duration of twelve months and which had failed at least three other forms of treatment. One hundred and fifty-two patients with chronic plantar fasciopathy were assigned to receive repetitive low-energy radial shock-wave therapy without local anesthesia, administered weekly for three weeks (Group 1, n = 73) or to receive the identical shock wave treatment and to perform an eight-week plantar fascia-specific stretching program (Group 2, n = 79). All patients completed the nine-item pain subscale of the validated Foot Function Index and a subject-relevant outcome questionnaire. Patients were evaluated at baseline, and at two, four, and twenty-four months after baseline. The primary outcome measures were a mean change in the Foot Function Index sum score at two months after baseline, a mean change in item 2 (pain during the first steps of walking in the morning) on this Index, and satisfaction with treatment. No difference in mean age, sex, weight or duration of symptoms was found between the groups at baseline. At two months after baseline, the Foot Function Index sum score showed significantly greater changes for the patients managed with shock-wave therapy plus plantar fascia-specific stretching than those managed with shock-wave therapy alone (p < 0.001), as well as individually for item 2 (p < 0.001). Twenty-four patients in Group 1 (32%) versus forty-seven patients in Group 2 (59%) were satisfied with the treatment (p < 0.001). Significant differences persisted at four months, but not at twenty-four months. A program of manual stretching exercises specific to the plantar fascia in combination with repetitive low-energy radial shock-wave therapy is more efficient than repetitive low-energy radial shock-wave therapy alone for the treatment of chronic symptoms of proximal plantar fasciopathy. Copyright © 2015 IJS Publishing Group Limited. Published by Elsevier Ltd. All rights reserved.

Holographic heavy ion collisions with baryon charge

DOE PAGES

Casalderrey-Solana, Jorge; Mateos, David; van der Schee, Wilke; ...

2016-09-19

We numerically simulate collisions of charged shockwaves in Einstein-Maxwell theory in anti-de Sitter space as a toy model of heavy ion collisions with non-zero baryon charge. The stress tensor and the baryon current become well described by charged hydrodynamics at roughly the same time. The effect of the charge density on generic observables is typically no larger than 15%. Finally, we find significant stopping of the baryon charge and compare our results with those in heavy ion collision experiments.

Modeling Nonlinear Elastic-plastic Behavior of RDX Single Crystals During Indentation

DTIC Science & Technology

2012-01-01

single crystals has also been probed using shock experiments (6, 12) and molecular dynamics simulations (12–14). RDX undergoes a polymorphic phase...Patterson, J.; Dreger, Z.; Gupta, Y. Shock-wave Induced Phase Transition in RDX Single Crystals. J. Phys. Chem. B 2007, 111, 10897–10904. 17. Bedrov, D...and Volume Compression of β - HMX and RDX . In Proc. Int. Symp. High Dynamic Pressures; Commissariat a l’Energie Atomique: Paris, 1978; pp 3–8. 24

Numerical and Analytical Study of Nonlinear Effects of Transonic Flow Past a Wing Airfoil in Oscillation of its Surface Element

NASA Astrophysics Data System (ADS)

Aul'chenko, S. M.; Zamuraev, V. P.; Kalinina, A. P.

2014-05-01

The present work is devoted to a criterial analysis and mathematical modeling of the influence of forced oscillations of surface elements of a wing airfoil on the shock-wave structure of transonic flow past it. Parameters that govern the regimes of interaction of the oscillatory motion of airfoil sections with the breakdown compression shock have been established. The qualitative and quantitative influence of these parameters on the wave resistance of the airfoil has been investigated.

Developing a laser shockwave model for characterizing diffusion bonded interfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lacy, Jeffrey M., E-mail: Jeffrey.Lacy@inl.gov; Smith, James A., E-mail: Jeffrey.Lacy@inl.gov; Rabin, Barry H., E-mail: Jeffrey.Lacy@inl.gov

2015-03-31

The US National Nuclear Security Agency has a Global Threat Reduction Initiative (GTRI) with the goal of reducing the worldwide use of high-enriched uranium (HEU). A salient component of that initiative is the conversion of research reactors from HEU to low enriched uranium (LEU) fuels. An innovative fuel is being developed to replace HEU in high-power research reactors. The new LEU fuel is a monolithic fuel made from a U-Mo alloy foil encapsulated in Al-6061 cladding. In order to support the fuel qualification process, the Laser Shockwave Technique (LST) is being developed to characterize the clad-clad and fuel-clad interface strengthsmore » in fresh and irradiated fuel plates. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves to characterize interfaces in nuclear fuel plates. However, because the deposition of laser energy into the containment layer on a specimen's surface is intractably complex, the shock wave energy is inferred from the surface velocity measured on the backside of the fuel plate and the depth of the impression left on the surface by the high pressure plasma pulse created by the shock laser. To help quantify the stresses generated at the interfaces, a finite element method (FEM) model is being utilized. This paper will report on initial efforts to develop and validate the model by comparing numerical and experimental results for back surface velocities and front surface depressions in a single aluminum plate representative of the fuel cladding.« less

Physicochemical model of detonation synthesis of nanoparticles from metal carboxylates

NASA Astrophysics Data System (ADS)

Tolochko, B. P.; Chernyshev, A. P.; Ten, K. A.; Pruuel, E. R.; Zhogin, I. L.; Zubkov, P. I.; Lyakhov, N. Z.; Luk'yanchikov, L. A.; Sheromov, M. A.

2008-02-01

We have shown previously that when metal carboxylates are subjected to a shock-wave action, diamond nanoparticles and nanoparticles of metals (Ag, Bi, Co, Fe, Pb) are formed and their characteristic size is about 30-200 Å. The metal nanoparticles formed are covered by an amorphous-carbon layer up to 20 Å thick. In this work we put forward a physicochemical model of the formation of diamond and metal nanoparticles from metal carboxylates upon shock-wave action. The energy released upon detonation inside the precursor is lower than in regions not occupied by the stearates. The characteristic time of temperature equalization has been estimated to be on the order of ˜10-3 s, which is greater by a factor of ˜103 than the characteristic reaction time. Due to the adiabatic nature of the processes occurring, the typical temperature of a "particle" will be lower than the temperature of the surrounding medium. In the framework of the model suggested, it has been assumed that the growth of metal clusters should occur by the diffusion mechanism; i.e., the "building material" is supplied through diffusion. The calculation using our previous experimental data on the reaction time and average size of metal particles has shown that the diffusion properties of the medium in which the metal nanoparticles are formed are close to those of the liquid state of the substance. The temperature and pressure under detonation conditions markedly exceed the analogous parameters characteristic of experiments on the thermodestruction of metal carboxylates. The small time of existence of the reaction mixture is compensated by the high mobility and concentration of reagents.

Large-Scale Reactive Atomistic Simulation of Shock-induced Initiation Processes in Energetic Materials

NASA Astrophysics Data System (ADS)

Thompson, Aidan

2013-06-01

Initiation in energetic materials is fundamentally dependent on the interaction between a host of complex chemical and mechanical processes, occurring on scales ranging from intramolecular vibrations through molecular crystal plasticity up to hydrodynamic phenomena at the mesoscale. A variety of methods (e.g. quantum electronic structure methods (QM), non-reactive classical molecular dynamics (MD), mesoscopic continuum mechanics) exist to study processes occurring on each of these scales in isolation, but cannot describe how these processes interact with each other. In contrast, the ReaxFF reactive force field, implemented in the LAMMPS parallel MD code, allows us to routinely perform multimillion-atom reactive MD simulations of shock-induced initiation in a variety of energetic materials. This is done either by explicitly driving a shock-wave through the structure (NEMD) or by imposing thermodynamic constraints on the collective dynamics of the simulation cell e.g. using the Multiscale Shock Technique (MSST). These MD simulations allow us to directly observe how energy is transferred from the shockwave into other processes, including intramolecular vibrational modes, plastic deformation of the crystal, and hydrodynamic jetting at interfaces. These processes in turn cause thermal excitation of chemical bonds leading to initial chemical reactions, and ultimately to exothermic formation of product species. Results will be presented on the application of this approach to several important energetic materials, including pentaerythritol tetranitrate (PETN) and ammonium nitrate/fuel oil (ANFO). In both cases, we validate the ReaxFF parameterizations against QM and experimental data. For PETN, we observe initiation occurring via different chemical pathways, depending on the shock direction. For PETN containing spherical voids, we observe enhanced sensitivity due to jetting, void collapse, and hotspot formation, with sensitivity increasing with void size. For ANFO, we examine the effect of reaction rates on shock direction, fuel oil fraction, and crystal/fuel oil/void microstructural arrangement. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Dept. of Energy's National Nuclear Security Admin. under contract DEAC0494AL85000.

Numerical investigations of shock wave interaction with laminar boundary layer on compressor profile

NASA Astrophysics Data System (ADS)

Piotrowicz, M.; Flaszyński, P.

2016-10-01

The investigation of shockwave boundary layer interaction on suction side of transonic compressor blade is one of main objectives of TFAST project (Transition Location Effect on Shock Wave Boundary Layer Interaction). In order to look more closely into the flow structure on suction side of a profile, a design of generic test section in linear transonic wind tunnel was proposed. The experimental and numerical results of flow structure on a suction side of the compressor profile investigations are presented. The numerical simulations are carried out for EARSM (Explicit Algebraic Reynolds Stress Model) turbulence model with transition model. The result are compared with oil flow visualisation, schlieren pictures, Pressure Sensitive Paint (PSP) and static pressure.

Influence of Shockwave Profile on Ejecta

NASA Astrophysics Data System (ADS)

Zellner, Michael B.; Dimonte, Guy; Germann, Timothy C.; Hammerberg, James E.; Rigg, Paulo A.; Stevens, Gerald D.; Turley, William D.; Buttler, William T.

2009-12-01

We investigate the relation between shock-pulse shape and the amount of micron-scale fragments ejected upon shock release at the metal/vacuum interface of shocked Sn targets. These micron-scale particles are commonly referred to as ejecta. Two shock-pulse shapes are considered: a supported shock created by impacting a Sn target with a sabot that was accelerated using a powder gun; and an unsupported or Taylor Shockwave, created by detonation of high explosive that was press-fit to the front-side of the Sn target. Ejecta production at the back-side or free-surface of the Sn coupons were characterized through use of piezoelectric pins, Asay foils, optical shadowgraphy, and x-ray attenuation.

Influence of Shockwave Profile on Ejection of Micron-Scale Material From Shocked Tin Surfaces

NASA Astrophysics Data System (ADS)

Zellner, Michael; Hammerberg, Jim; Hixson, Robert; Olson, Russel; Rigg, Paulo; Stevens, Gerald; Turley, William; Buttler, William

2008-03-01

This effort investigates the relation between shock-pulse shape and the amount of micron-scale fragments ejected (ejecta) upon shock release at the metal/vacuum interface of shocked Sn targets. Two shock-pulse shapes are considered: a supported shock created by impacting a Sn target with a sabot that was accelerated using a powder gun; and an unsupported or triangular-shaped Taylor shockwave, created by detonation of high explosive that was press-fit to the front-side of the Sn target. Ejecta production at the back-side or free-side of the Sn coupons were characterized through use of piezoelectric pins, Asay foil, optical shadowgraphy, and X-ray attenuation.

NASA's F-15B from the Dryden Flight Research Center flew in the supersonic shockwave of a modified U.S. Navy F-5E jet in support of the Shaped Sonic Boom Demonstration (SSBD) project. On Aug. 27, 2003, the F-5 SSBD aircraft demonstrated a method to reduce

NASA Image and Video Library

2003-08-25

NASA's F-15B research testbed jet from NASA's Dryden Flight Research Center flew in the supersonic shockwave of a Northrop Grumman Corp. modified U.S. Navy F-5E jet in support of the Shaped Sonic Boom Demonstration (SSBD) project, which is part of the DARPA's Quiet Supersonic Platform (QSP) program. On Aug. 27, 2003, the F-5 SSBD aircraft demonstrated a method to reduce the intensity of sonic booms.

Laser-excited gold nanoparticles for treatment of cancer cells in vitro

NASA Astrophysics Data System (ADS)

Zamora-Romero, Noé; Robles, Vicente; Alvarez, Crysthal; Cuando-Espitia, Natanael; Devia-Cruz, Luis F.; Penilla, Elias; Halaney, David L.; Aguilar, Guillermo

2017-07-01

Several in vitro and in vivo studies have been performed to investigate the potential of Photothermal Therapy (PTT) as a cancer treatment strategy. However, there are still open questions concerning the optimal parameters for generating cavitation bubbles and acoustic shockwaves for increasing the damage to malignant cells, and the primary mechanism for cell damage in PTT is still a matter of debate. This study investigates PTT based on shockwaves from cavitation induced far from the cells, due to laser absorption by gold nanorods (GNR) colloidal solutions in vitro. The effects of laser energy and distance from the cavitation on cell viability is investigated in PC3 prostate cancer cells, and Escherichia coli (E. coli) cells, respectively.

Extracorporeal shockwave lithotripsy of distal ureteral calculi.

PubMed

Miller, K; Bubeck, J R; Hautmann, R

1986-01-01

To date, the use of extracorporeal shockwave lithotripsy (ESWL) has been limited to renal calculi and ureteral calculi above the pelvic brim. Modifying the position of the patient on the support of the Dornier lithotripter HM3, we were able to localize and treat distal ureteral calculi. Until April 1986, 43 patients with stones in the lower ureter underwent contact-free lithotripsy. Treatment was successful in 39 patients (90%), 2 of these requiring 2 sessions. In 4 patients treatment failed and stone removal was accomplished using ureteroscopy or open surgery. No complications or adverse side effects were encountered in the whole series. ESWL is now the method of choice for the treatment of distal ureteral calculi in our department.

Angular distributions of the protons in the reaction. pi. /sup +/+Xe. -->. p+xxx at 2. 34 GeV/c as a background for the shock-wave effect

DOE Office of Scientific and Technical Information (OSTI.GOV)

Slowinski, B.; Strugalski, Z.

1977-02-20

Results are presented of an analysis of the angular distributions of protons with E/sub p/> or =30 MeV emitted with different numbers of secondary charged particles in ..pi../sup +/+Xe interactions at 2.34 GeV/c. The obtained distributions are compared with the analogous characteristics of the protons emitted in collisions of protons or ..cap alpha.. particles with heavy emulsion nuclei and with lead at 70 and 17 GeV/c. It is concluded that the investigated distributions reveal no irregularities capable of attesting to a noticable role of the shock-wave mechanism in the target nuclei.

Comparison between phenomenological and ab-initio reaction and relaxation models in DSMC

NASA Astrophysics Data System (ADS)

Sebastião, Israel B.; Kulakhmetov, Marat; Alexeenko, Alina

2016-11-01

New state-specific vibrational-translational energy exchange and dissociation models, based on ab-initio data, are implemented in direct simulation Monte Carlo (DSMC) method and compared to the established Larsen-Borgnakke (LB) and total collision energy (TCE) phenomenological models. For consistency, both the LB and TCE models are calibrated with QCT-calculated O2+O data. The model comparison test cases include 0-D thermochemical relaxation under adiabatic conditions and 1-D normal shockwave calculations. The results show that both the ME-QCT-VT and LB models can reproduce vibrational relaxation accurately but the TCE model is unable to reproduce nonequilibrium rates even when it is calibrated to accurate equilibrium rates. The new reaction model does capture QCT-calculated nonequilibrium rates. For all investigated cases, we discuss the prediction differences based on the new model features.

Shockwave Processing of Composite Boron and Titanium Nitride Powders

NASA Astrophysics Data System (ADS)

Beason, Matthew T.; Gunduz, I. Emre; Mukasyan, Alexander S.; Son, Steven F.

2015-06-01

Shockwave processing of powders has been shown to initiate reactions between condensed phase reactants. It has been observed that these reactions can occur at very short timescales, resulting in chemical reactions occurring at a high pressure state. These reactions have the potential to produce metastable phases. Kinetic limitations prevent gaseous reactants from being used in this type of synthesis reaction. To overcome this limitation, a solid source of gaseous reactants must be used. An example of this type of reaction is the nitrogen exchange reaction (e.g. B + TiN, B + Si3N4 etc.). In these reactions nitrogen is ``carried'' by a material that can be then reduced by the second reactant. This work explores the possibility of using nitrogen exchange reactions to synthesize the cubic phase of boron nitride (c-BN) through shockwave processing of ball milled mixtures of boron and titanium nitride. The heating from the passage of the shock wave (pore collapse, plastic work, etc.) combined with thermochemical energy from the reaction may provide a means to synthesize c-BN. This material is based upon work supported by the Department of Energy, National Nuclear Security Administration, under Award Number(s) DE-NA0002377. National Defense Science & Engineering Graduate Fellowship (NDSEG), 32 CFR 168a.

Prognostic factors for the outcome of extracorporeal shockwave therapy for calcific tendinitis of the shoulder.

PubMed

Chou, W-Y; Wang, C-J; Wu, K-T; Yang, Y-J; Ko, J-Y; Siu, K-K

2017-12-01

We conducted a study to identify factors that are prognostic of the outcome of extracorporeal shockwave therapy (ESWT) for calcific tendinitis of the shoulder. Since 1998, patients with symptomatic calcific tendinitis of the rotator cuff have been treated with ESWT using an electrohydraulic mode shockwave device. One year after ESWT, patients were grouped according to the level of resorption of calcification. Of 241 symptomatic shoulders, complete resorption (CR) of calcification occurred in 134 (CR group). The remaining 107 shoulders had incomplete resorption (ICR) (ICR group). Gartner type I calcification was most common (64.5%) in the ICR group. The mean duration of symptoms before ESWT was significantly longer in the ICR group. Overall, 81% of the CR group and 23.4% of the ICR group were symptom free. There was a strong relationship between subsidence of symptoms and remission of calcification. Poor prognosis was significantly related to Gartner type I calcification, calcification extent > 15 mm and duration of symptoms > 11 months. Patients with calcific tendinitis of the shoulder who have the factors identified for a poor outcome after ESWT should undergo a different procedure. Cite this article: Bone Joint J 2017;99-B:1643-50. ©2017 The British Editorial Society of Bone & Joint Surgery.

The pulsed dye laser versus the Q-switched Nd:YAG laser in laser-induced shock-wave lithotripsy.

PubMed

Thomas, S; Pensel, J; Engelhardt, R; Meyer, W; Hofstetter, A G

1988-01-01

To date, there are two fairly well-established alternatives for laser-induced shock-wave lithotripsy in clinical practice. The Q-switched Nd:YAG laser is distinguished by the high-stone selectivity of its coupler systems. The necessity of a coupler system and its fairly small conversion rate of light energy into mechanical energy present serious drawbacks. Furthermore, the minimal outer diameter of the transmission system is 1.8 mm. The pulsed-dye laser can be used with a highly flexible and uncomplicated 200-micron fiber. However, the laser system itself is more complicated than the Q-switched Nd:YAG laser and requires a great deal of maintenance. Biological evaluation of damage caused by direct irradiation shows that both laser systems produce minor damage of different degrees. YAG laser lithotripsy with the optomechanical coupler was assessed in 31 patients with ureteral calculi. The instability and limited effectiveness of the fiber application system necessitated auxiliary lithotripsy methods in 14 cases. Dye-laser lithotripsy is currently being tested in clinical application. Further development, such as systems for blind application or electronic feedback mechanisms to limit adverse tissue effects, have yet to be optimized. Nevertheless, laser-induced shock-wave lithotripsy has the potential to become a standard procedure in the endourologic management of stone disease.

Stable aqueous dispersions of functionalized multi-layer graphene by pulsed underwater plasma exfoliation of graphite

NASA Astrophysics Data System (ADS)

Meyer-Plath, Asmus; Beckert, Fabian; Tölle, Folke J.; Sturm, Heinz; Mülhaupt, Rolf

2016-02-01

A process was developed for graphite particle exfoliation in water to stably dispersed multi-layer graphene. It uses electrohydraulic shockwaves and the functionalizing effect of solution plasma discharges in water. The discharges were excited by 100 ns high voltage pulsing of graphite particle chains that bridge an electrode gap. The underwater discharges allow simultaneous exfoliation and chemical functionalization of graphite particles to partially oxidized multi-layer graphene. Exfoliation is caused by shockwaves that result from rapid evaporation of carbon and water to plasma-excited gas species. Depending on discharge energy and locus of ignition, the shockwaves cause stirring, erosion, exfoliation and/or expansion of graphite flakes. The process was optimized to produce long-term stable aqueous dispersions of multi-layer graphene from graphite in a single process step without requiring addition of intercalants, surfactants, binders or special solvents. A setup was developed that allows continuous production of aqueous dispersions of flake size-selected multi-layer graphenes. Due to the well-preserved sp2-carbon structure, thin films made from the dispersed graphene exhibited high electrical conductivity. Underwater plasma discharge processing exhibits high innovation potential for morphological and chemical modifications of carbonaceous materials and surfaces, especially for the generation of stable dispersions of two-dimensional, layered materials.

Shock-induced collapse of a gas bubble in shockwave lithotripsy.

PubMed

Johnsen, Eric; Colonius, Tim

2008-10-01

The shock-induced collapse of a pre-existing nucleus near a solid surface in the focal region of a lithotripter is investigated. The entire flow field of the collapse of a single gas bubble subjected to a lithotripter pulse is simulated using a high-order accurate shock- and interface-capturing scheme, and the wall pressure is considered as an indication of potential damage. Results from the computations show the same qualitative behavior as that observed in experiments: a re-entrant jet forms in the direction of propagation of the pulse and penetrates the bubble during collapse, ultimately hitting the distal side and generating a water-hammer shock. As a result of the propagation of this wave, wall pressures on the order of 1 GPa may be achieved for bubbles collapsing close to the wall. The wall pressure decreases with initial stand-off distance and pulse width and increases with pulse amplitude. For the stand-off distances considered in the present work, the wall pressure due to bubble collapse is larger than that due to the incoming shockwave; the region over which this holds may extend to ten initial radii. The present results indicate that shock-induced collapse is a mechanism with high potential for damage in shockwave lithotripsy.

Shock-induced collapse of a gas bubble in shockwave lithotripsy

PubMed Central

Johnsen, Eric; Colonius, Tim

2008-01-01

The shock-induced collapse of a pre-existing nucleus near a solid surface in the focal region of a lithotripter is investigated. The entire flow field of the collapse of a single gas bubble subjected to a lithotripter pulse is simulated using a high-order accurate shock- and interface-capturing scheme, and the wall pressure is considered as an indication of potential damage. Results from the computations show the same qualitative behavior as that observed in experiments: a re-entrant jet forms in the direction of propagation of the pulse and penetrates the bubble during collapse, ultimately hitting the distal side and generating a water-hammer shock. As a result of the propagation of this wave, wall pressures on the order of 1 GPa may be achieved for bubbles collapsing close to the wall. The wall pressure decreases with initial stand-off distance and pulse width and increases with pulse amplitude. For the stand-off distances considered in the present work, the wall pressure due to bubble collapse is larger than that due to the incoming shockwave; the region over which this holds may extend to ten initial radii. The present results indicate that shock-induced collapse is a mechanism with high potential for damage in shockwave lithotripsy. PMID:19062841

Hugoniot equation of state and dynamic strength of boron carbide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grady, Dennis E.

Boron carbide ceramics have been particularly problematic in attempts to develop adequate constitutive model descriptions for purposes of analysis of dynamic response in the shock and impact environment. Dynamic strength properties of boron carbide ceramic differ uniquely from comparable ceramics. Furthermore, boron carbide is suspected, but not definitely shown, to undergoing polymorphic phase transformation under shock compression. In the present paper, shock-wave compression measurements conducted over the past 40 years are assessed for the purpose of achieving improved understanding of the dynamic equation of state and strength of boron carbide. In particular, attention is focused on the often ignored Losmore » Alamos National Laboratory (LANL) Hugoniot measurements performed on porous sintered boron carbide ceramic. The LANL data are shown to exhibit two compression anomalies on the shock Hugoniot within the range of 20–60 GPa that may relate to crystallographic structure transitions. More recent molecular dynamics simulations on the compressibility of the boron carbide crystal lattice reveal compression transitions that bear similarities to the LANL Hugoniot results. The same Hugoniot data are complemented with dynamic isentropic compression data for boron carbide extracted from Hugoniot measurements on boron carbide and copper granular mixtures. Other Hugoniot measurements, however, performed on near-full-density boron carbide ceramic differ markedly from the LANL Hugoniot data. These later data exhibit markedly less compressibility and tend not to show comparable anomalies in compressibility. Alternative Hugoniot anomalies, however, are exhibited by the near-full-density data. Experimental uncertainty, Hugoniot strength, and phase transformation physics are all possible explanations for the observed discrepancies. It is reasoned that experimental uncertainty and Hugoniot strength are not likely explanations for the observed differences. The notable mechanistic difference in the processes of shock compression between the LANL data and that of the other studies is the markedly larger inelastic deformation and dissipation experienced in the shock event brought about by compaction of the substantially larger porosity LANL test ceramics. High-pressure diamond anvil cell experiments reveal extensive amorphization, reasoned to be a reversion product of a higher-pressure crystallographic phase, which is a consequence of application of both high pressure and shear deformation to the boron carbide crystal structure. A dependence of shock-induced high-pressure phase transformation in boron carbide on the extent of shear deformation experienced in the shock process offers a plausible explanation for the differences observed in the LANL Hugoniot data on porous ceramic and that of other shock data on near-full-density boron carbide.« less

The multipath propagation effect in gunshot acoustics and its impact on the design of sniper positioning systems

NASA Astrophysics Data System (ADS)

Ramos, António L. L.; Holm, Sverre; Gudvangen, Sigmund; Otterlei, Ragnvald

2013-06-01

Counter sniper systems rely on the detection and parameter estimation of the shockwave and the muzzle blast in order to determine the sniper location. In real-world situations, these acoustical signals can be disturbed by natural phenomena like weather and climate conditions, multipath propagation effect, and background noise. While some of these issues have received some attention in recent publications with application to gunshot acoustics, the multipath propagation phenomenon whose effect can not be neglected, specially in urban environments, has not yet been discussed in details in the technical literature in the same context. Propagating sound waves can be reflected at the boundaries in the vicinity of sound sources or receivers, whenever there is a difference in acoustical impedance between the reflective material and the air. Therefore, the received signal can be composed of a direct-path signal plus N scaled delayed copies of that signal. This paper presents a discussion on the multipath propagation effect and its impact on the performance and reliability of sniper positioning systems. In our formulation, propagation models for both the shockwave and the muzzle blast are considered and analyzed. Conclusions following the theoretical analysis of the problem are fully supported by actual gunshots acoustical signatures.

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

NASA Technical Reports Server (NTRS)

Dudek, Julianne C.; Carlson, Jan-Renee

2017-01-01

Full seven-equation Reynolds stress turbulence models are promising tools for today’s aerospace technology challenges. This paper examines two such models for computing challenging turbulent flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSG/LRR full second-moment Reynolds stress models have been implemented into the FUN3D (Fully Unstructured Navier-Stokes Three Dimensional) unstructured Navier-Stokes code and were evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results computed using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST-V) two-equation turbulence models.

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

NASA Technical Reports Server (NTRS)

Dudek, Julianne C.; Carlson, Jan-Renee

2017-01-01

Full seven-equation Reynolds stress turbulence models are a relatively new and promising tool for todays aerospace technology challenges. This paper uses two stress-omega full Reynolds stress models to evaluate challenging flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSG/LRR full second-moment Reynolds stress models have been implemented into the FUN3D (Fully Unstructured Navier-Stokes Three Dimensional) unstructured Navier-Stokes code and are evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST-V) two-equation turbulence models.

Experimental Investigation of the Effects of Viscosity on the Drag and Base Pressure of Bodies of Revolution at a Mach Number 1.5

NASA Technical Reports Server (NTRS)

Chapman, Dean R; Perkins, Edward W

1951-01-01

Models were tested to evaluate effects of Reynolds number for both laminar and turbulent boundary layers. Principal geometric variables investigated were afterbody shape and length-diameter ratio. Force tests and base-pressure measurements were made. Schlieren photographs were used to analyze the effects of viscosity on flow separation and shock-wave configuration and to verify the condition of the boundary layer as deduced from the force tests. The results are discussed and compared with theoretical calculations.

CFD propels NASP propulsion progress

NASA Technical Reports Server (NTRS)

Povinelli, Louis A.; Dwoyer, Douglas L.; Green, Michael J.

1990-01-01

The most complex aerothermodynamics encountered in the National Aerospace Plane (NASP) propulsion system are associated with the fuel-mixing and combustion-reaction flows of its combustor section; adequate CFD tools must be developed to model shock-wave systems, turbulent hydrogen/air mixing, flow separation, and combustion. Improvements to existing CFD codes have involved extension from two dimensions to three, as well as the addition of finite-rate hydrogen-air chemistry. A novel CFD code for the treatment of reacting flows throughout the NASP, designated GASP, uses the most advanced upwind-differencing technology.

CFD propels NASP propulsion progress

NASA Astrophysics Data System (ADS)

Povinelli, Louis A.; Dwoyer, Douglas L.; Green, Michael J.

1990-07-01

The most complex aerothermodynamics encountered in the National Aerospace Plane (NASP) propulsion system are associated with the fuel-mixing and combustion-reaction flows of its combustor section; adequate CFD tools must be developed to model shock-wave systems, turbulent hydrogen/air mixing, flow separation, and combustion. Improvements to existing CFD codes have involved extension from two dimensions to three, as well as the addition of finite-rate hydrogen-air chemistry. A novel CFD code for the treatment of reacting flows throughout the NASP, designated GASP, uses the most advanced upwind-differencing technology.

In Situ Activation of Penile Progenitor Cells With Low-Intensity Extracorporeal Shockwave Therapy.

PubMed

Lin, Guiting; Reed-Maldonado, Amanda B; Wang, Bohan; Lee, Yung-Chin; Zhou, Jun; Lu, Zhihua; Wang, Guifang; Banie, Lia; Lue, Tom F

2017-04-01

We previously reported that progenitor cells, or stem cells, exist within penile tissue. We hypothesized that acoustic wave stimulation by low-intensity extracorporeal shockwave therapy (Li-ESWT) would activate local stem or progenitor cells within the penis, producing regenerative effects. To study the feasibility of in situ penile progenitor cell activation by Li-ESWT. We performed a cohort analysis of young and middle-age male Sprague-Dawley rats treated with 5-ethynyl-2'-deoxyuridine (EdU) pulse followed by Li-ESWT. In addition, Li-ESWT was applied to cultured Schwann cells and endothelial cells to study the molecular mechanism involved in cell proliferation. Thirty minutes before Li-ESWT, each rat received an intraperitoneal injection of EdU. Li-ESWT was applied to the penis at very low (0.02 mJ/mm 2 at 3 Hz for 300 pulses) or low (0.057 mJ/mm 2 at 3 Hz for 500 pulses) energy levels. The endothelial and Schwann cells were treated with very low energy (0.02 mJ/mm 2 at 3 Hz for 300 pulses) in vitro. At 48 hours or 1 week after Li-ESWT, penile tissues were harvested for histologic study to assess EdU + and Ki-67 + cells, and cell proliferation, Ki-67 expression, Erk1/2 phosphorylation, translocation, and angiogenesis were examined in cultured Schwann and endothelial cells after Li-ESWT. Li-ESWT significantly increased EdU + cells within penile erectile tissues (P < .01) at 48 hours and 1 week. There were more cells activated in young animals than in middle-age animals, and the effect depended on dosage. Most activated cells were localized within subtunical spaces. In vitro studies indicated that Li-ESWT stimulated cell proliferation through increased phosphorylation of Erk1/2. The present results provide a possible explanation for the clinical benefits seen with Li-ESWT. The main limitation of the present project was the short period of study and the animal model used. Li-ESWT could be less effective in improving erectile function in old animals because of the decreased number and quality of penile stem or progenitor cells associated with aging. Li-ESWT activation of local penile progenitor cells might be one of the mechanisms that contribute to the beneficial effects of shockwave treatment for erectile dysfunction, which represents a non-invasive alternative to exogenous stem cell therapy. Lin G, Reed-Maldonado AB, Wang B, et al. In Situ Activation of Penile Progenitor Cells With Low-Intensity Extracorporeal Shockwave Therapy. J Sex Med 2017;14:493-501. Copyright © 2017 International Society for Sexual Medicine. Published by Elsevier Inc. All rights reserved.

A Theoretical Investigation of Radial Lateral Wells with Shockwave Completion in Shale Gas Reservoirs

NASA Astrophysics Data System (ADS)

Shan, Jia

As its role in satisfying the energy demand of the U.S. and as a clean fuel has become more significant than ever, the shale gas production in the U.S. has gained increasing momentum over recent years. Thus, effective and environmentally friendly methods to extract shale gas are critical. Hydraulic fracturing has been proven to be efficient in the production of shale gas. However, environmental issues such as underground water contamination and high usage of water make this technology controversial. A potential technology to eliminate the environmental issues concerning water usage and contamination is to use blast fracturing, which uses explosives to create fractures. It can be further aided by HEGF and multi-pulse pressure loading technology, which causes less crushing effect near the wellbore and induces longer fractures. Radial drilling is another relatively new technology that can bypass damage zones due to drilling and create a larger drainage area through drilling horizontal wellbores. Blast fracturing and radial drilling both have the advantage of cost saving. The successful combination of blast fracturing and radial drilling has a great potential for improving U.S. shale gas production. An analytical productivity model was built in this study, considering linear flow from the reservoir rock to the fracture face, to analyze factors affecting shale gas production from radial lateral wells with shockwave completion. Based on the model analyses, the number of fractures per lateral is concluded to be the most effective factor controlling the productivity index of blast-fractured radial lateral wells. This model can be used for feasibility studies of replacing hydraulic fracturing by blast fracturing in shale gas well completions. Prediction of fracture geometry is recommended for future studies.

Effects of shock-breakout pressure on ejection of micron-scale material from shocked tin surfaces

NASA Astrophysics Data System (ADS)

Zellner, M. B.; Grover, M.; Hammerberg, J. E.; Hixson, R. S.; Iverson, A. J.; Macrum, G. S.; Morley, K. B.; Obst, A. W.; Olson, R. T.; Payton, J. R.; Rigg, P. A.; Routley, N.; Stevens, G. D.; Turley, W. D.; Veeser, L.; Buttler, W. T.

2007-07-01

This effort investigates the relation between ejecta production and shock-breakout pressure (PSB) for Sn shocked with a Taylor shockwave (unsupported) to pressures near the solid-on-release/partial melt-on-release phase transition region. The shockwaves were created by detonation of high explosive (HE) PBX-9501 on the front side of Sn coupons. Ejecta production at the backside or free side of the Sn coupons was characterized through use of piezoelectric pins, optical shadowgraphy, x-ray attenuation radiography, and optical-heterodyne velocimetry. Ejecta velocities, dynamic volume densities, and areal densities were then correlated with the shock-breakout pressure of Sn surfaces characterized by roughness average of Ra=16 μin or Ra=32 μin.

Turbulence measurements in hypersonic shock-wave boundary-layer interaction flows

NASA Technical Reports Server (NTRS)

Mikulla, V.; Horstman, C. C.

1976-01-01

Turbulent intensity and Reynolds shear stress measurements are presented for two nonadiabatic hypersonic shock-wave boundary-layer interaction flows, one with and one without separation. These measurements were obtained using a new hot-wire probe specially designed for heated flows. Comparison of the separated and attached flows shows a significant increase above equilibrium values in the turbulent intensity and shear stress downstream of the interaction region for the attached case, while for the separated case, the turbulent fluxes remain close to equilibrium values. This effect results in substantial differences in turbulence lifetime for the two flows. We propose that these differences are due to a coupling between the turbulent energy and separation bubble unsteadiness, a hypothesis supported by the statistical properties of the turbulent fluctuations.

Fast discharge in a plasma gun with hemispherical insulator

NASA Astrophysics Data System (ADS)

Antsiferov, P. S.; Dorokhin, L. A.; Sidelnikov, Yu. V.; Koshelev, K. N.

2009-05-01

A method of creation of hot dense plasma is proposed. It is based on cumulation of a shockwave, which originates on a hemispherical surface of insulator of plasma gun. The results of first experiments are presented. The shock wave is driven by fast electrical discharge (dI /dt>1012 A/s). The inductive storage with semiconductor opening switch is used as a current driver. Time resolved pin-hole images and vacuum ultraviolet (vuv) spectra are studied. Shockwaves from hemispherical insulator with 4 mm radius create plasma with a form of column about 1 mm diameter and 3-4 mm length. vuv spectra contain the lines of Ar ions that corresponds to the electron temperature about 20 eV. Possible practical application is discussed.

Experimental investigation on dynamic characteristics and strengthening mechanism of laser-induced cavitation bubbles.

PubMed

Ren, X D; He, H; Tong, Y Q; Ren, Y P; Yuan, S Q; Liu, R; Zuo, C Y; Wu, K; Sui, S; Wang, D S

2016-09-01

The dynamic features of nanosecond laser-induced cavitation bubbles near the light alloy boundary were investigated with the high-speed photography. The shock-waves and the dynamic characteristics of the cavitation bubbles generated by the laser were detected using the hydrophone. The dynamic features and strengthening mechanism of cavitation bubbles were studied. The strengthening mechanisms of cavitation bubble were discussed when the relative distance parameter γ was within the range of 0.5-2.5. It showed that the strengthening mechanisms caused by liquid jet or shock-waves depended on γ much. The research results provided a new strengthening method based on laser-induced cavitation shotless peening (CSP). Copyright © 2016 Elsevier B.V. All rights reserved.

Variable-intercept panel model for deformation zoning of a super-high arch dam.

PubMed

Shi, Zhongwen; Gu, Chongshi; Qin, Dong

2016-01-01

This study determines dam deformation similarity indexes based on an analysis of deformation zoning features and panel data clustering theory, with comprehensive consideration to the actual deformation law of super-high arch dams and the spatial-temporal features of dam deformation. Measurement methods of these indexes are studied. Based on the established deformation similarity criteria, the principle used to determine the number of dam deformation zones is constructed through entropy weight method. This study proposes the deformation zoning method for super-high arch dams and the implementation steps, analyzes the effect of special influencing factors of different dam zones on the deformation, introduces dummy variables that represent the special effect of dam deformation, and establishes a variable-intercept panel model for deformation zoning of super-high arch dams. Based on different patterns of the special effect in the variable-intercept panel model, two panel analysis models were established to monitor fixed and random effects of dam deformation. Hausman test method of model selection and model effectiveness assessment method are discussed. Finally, the effectiveness of established models is verified through a case study.

Cavitation in ultrasound and shockwave therapy

NASA Astrophysics Data System (ADS)

Colonius, Tim

2014-11-01

Acoustic waves, especially high-intensity ultrasound and shock waves, are used for medical imaging and intra- and extra-corporeal manipulation of cells, tissue, and urinary calculi. Waves are currently used to treat kidney stone disease, plantar fasciitis, and bone nonunion, and they are being investigated as a technique to ablate cancer tumors and mediate drug delivery. In many applications, acoustic waves induce the expansion and collapse of preexisting or newly cavitating bubbles whose presence can either mediate the generation of localized stresses or lead to collateral damage, depending on how effectively they can be controlled. We describe efforts aimed at simulating the collapse of bubbles, both individually and in clusters, with the aim to characterize the induced mechanical stresses and strains. To simulate collapse of one or a few bubbles, compressible Euler and Navier-Stokes simulations of multi-component materials are performed with WENO-based shock and interface capturing schemes. Repetitive insonification generates numerous bubbles that are difficult to resolve numerically. Such clouds are also important in traditional engineering applications such as caveating hydrofoils. Models that incorporate the dynamics of an unresolved dispersed phase consisting of the bubble cloud are also developed. The results of several model problems including bubble collapse near rigid surfaces, bubble collapse near compliant surfaces and in small capillaries are analyzed. The results are processed to determine the potential for micron-sized preexisting gas bubbles to damage capillaries. The translation of the fundamental fluid dynamics into improvements in the design and clinical application of shockwave lithotripters will be discussed. NIH Grant PO1-DK043881.

Generation of cylindrically convergent shockwaves in water on the MACH facility

NASA Astrophysics Data System (ADS)

Bland, Simon; Krasik, Ya. E.; Yanuka, D.; Gardner, R.; MacDonald, J.; Virozub, A.; Efimov, S.; Gleizer, S.; Chaturvedi, N.

2017-06-01

We report on the first experiments utilizing MACH facility at Imperial College London to explode copper wire arrays in water, generating extremely symmetric, cylindrical convergent shockwaves. The experiments were carried out with 10mm diameter arrays consisting of 60 × 130 μm wires, and currents >500 kA were achieved despite the high inductance load. Laser backlit framing images and streak photography of the implosion showed a highly uniform, stable shockwave that travelled towards the axis at velocities up to 7.5 kms-1. For the first time, imaging of the shock front has been carried at radii < 0.5 mm, and there is strong evidence that even at radii < 0.1 mm the shock front remains stable, resulting in a convergence ratio of 50:1. 2D hydrodynamic simulations that match the experimentally obtained implosion trajectory suggest pressures of >1 Mbar are produced within 10 μm of the axis, with water densities 3 gcm-3 and temperatures of many 1000 s of Kelvin. The results represent a significant step in the application of the technique to drive different material samples, and calculations of scaling the technique to larger pulsed power facilities are presented. This work was supported by the Institute of Shock Physics, funded by AWE Aldermaston, and the NNSA under DOE Cooperative Agreement Nos. DE-F03-02NA00057 and DE-SC-0001063.

A class of ejecta transport test problems

NASA Astrophysics Data System (ADS)

Oro, David M.; Hammerberg, J. E.; Buttler, William T.; Mariam, Fesseha G.; Morris, Christopher L.; Rousculp, Chris; Stone, Joseph B.

2012-03-01

Hydro code implementations of ejecta dynamics at shocked interfaces presume a source distribution function of particulate masses and velocities, f0(m,u;t). Some properties of this source distribution function have been determined from Taylor- and supported-shockwave experiments. Such experiments measure the mass moment of f0 under vacuum conditions assuming weak particle-particle interactions and, usually, fully inelastic scattering (capture) of ejecta particles from piezoelectric diagnostic probes. Recently, planar ejection of W particles into vacuum, Ar, and Xe gas atmospheres have been carried out to provide benchmark transport data for transport model development and validation. We present those experimental results and compare them with modeled transport of the W-ejecta particles in Ar and Xe.

Simulation of a turbulent supersonic underexpanded jet flowing into a submerged space with the help of a shear stress transfer model

NASA Astrophysics Data System (ADS)

Isaev, S. A.; Lipnitskii, Yu. M.; Baranov, P. A.; Panasenko, A. V.; Usachov, A. E.

2012-11-01

We have calculated the flow of an axisymmetric turbulent supersonic underexpanded jet into a submerged space with the help of the VP2/3 package as part of the generalized pressure correction procedure. The shear stress transfer model modified with account for the curvature of streamlines has been verified on the basis of comparison with V. I. Zapryagaev's data obtained at the S. A. Khristianovich Institute of Theoretical and Applied Mechanics, Siberian Branch of the Russian Academy of Sciences. The influence of the generated vortex viscosity on the shock-wave structure of the jet, the field of flow parameters, and the turbulence characteristics has been analyzed.

ESA is hot on the trail of Geminga

NASA Astrophysics Data System (ADS)

XMM-Newton image of Geminga showing the discovery of the twi hi-res Size hi-res: 68 kb Credits: ESA XMM-Newton image of Geminga showing the discovery of the twin tails This image was captured by the EPIC camera on board the satellite. The motion of Geminga across the sky is indicated, showing that the tails are trailing the neutron star. The scale bar corresponds to a distance of 1.5 million million kilometres at the distance of Geminga. Computer models of the shock wave created by Geminga hi-res Size hi-res: 522 kb Credits: Patrizia Caraveo Computer models of the shockwave created by Geminga Computer models of the shockwave created by Geminga show that the best matches to the data occur if the neutron star is travelling virtually across our line of sight. These correspond to the inclinations of less than 30 degrees. A neutron star measures only 20-30 kilometres across and is the dense remnant of an exploded star. Geminga is one of the closest to Earth, at a distance of about 500 light-years. Most neutron stars emit radio emissions, appearing to pulsate like a lighthouse, but Geminga is 'radio-quiet'. It does, however, emit huge quantities of pulsating gamma rays making it one of the brightest gamma-ray sources in the sky. Geminga is the only example of a successfully identified gamma-ray source from which astronomers have gained significant knowledge. It is 350 000 years old and ploughs through space at 120 kilometres per second. Its route creates a shockwave that compresses the gas of the interstellar medium and its naturally embedded magnetic field by a factor of four. Patrizia Caraveo, Instituto di Astrofisica Spaziale e Fisica Cosmica, Milano, Italy, and her colleagues (at CESR, France, ESO and MPE, Germany) have calculated that the tails are produced because highly energetic electrons become trapped in this enhanced magnetic field. As the electrons spiral inside the magnetic field, they emit the X-rays seen by XMM-Newton. The electrons themselves are created close to the neutron star. Geminga’s breathless rotation rate - once every quarter of a second - creates an extraordinary environment in which electrons and positrons, their antimatter counterparts, can be accelerated to extraordinarily high energies. At such energies, they become powerful high-energy gamma-ray producers. Astronomers had assumed that all the electrons would be converted into gamma rays. However, the discovery of the tails proves that some do find escape routes from the maelstrom. “It is astonishing that such energetic electrons succeed in escaping to create these tails,” says Caraveo, “The tail electrons have an energy very near to the maximum energy achievable in the environment of Geminga.” The tails themselves are the bright edges of the three-dimensional shockwave sculpted by Geminga. Such shockwaves are a bit like the wake of a ship travelling across the ocean. Using a computer model, the team has estimated that Geminga is travelling almost directly across our line of sight. Studies of Geminga could not be more important. The majority of known gamma-ray sources in the Universe have yet to be identified with known classes of celestial objects. Some astronomers believe that a sizeable fraction of them may be Geminga-like radio-quiet neutron stars. Certainly, the family of radio-quiet neutron stars, discovered through their X-ray emission, is continuously growing. Currently, about a dozen objects are known but only Geminga has a pair of tails! Note for editors During the search to track down this elusive celestial object, a co-author on the paper, Giovanni Bignami, named Geminga almost 30 years ago. He was Principal Investigator of XMM-Newton's EPIC camera from 1987 to1997 and is now Director of the Centre d'Etude Spatiale des Rayonnements (CESR). Geminga was first glimpsed as a mysterious source of gamma rays, coming from somewhere in the constellation Gemini by NASA's SAS-2 spacecraft in 1973. While searching to pin down its exact location and nature, Bignami named it Geminga because it was a 'Gemini gamma-ray source'. As an astronomer in Milan, Italy, he was also aware that in his native dialect 'gh'è minga' means 'it is not there', which he found amusing. It was also remarkably apt, for it was not until 1993 that he succeeded in finally 'seeing' and therefore pinpointing Geminga, using optical wavelengths. While it lacked radio emissions, the pulsating X-ray and gamma-ray emissions meant Geminga could only be a new class of radio-quiet neutron star. The original paper was published yesterday, 24 July 2003, on Science Express, a feature of Science Online.

Turbulence measurements in hypersonic shock-wave boundary-layer interaction flows

NASA Technical Reports Server (NTRS)

Mikulla, V.; Horstman, C. C.

1976-01-01

Turbulent intensity and Reynolds shear stress measurements are presented for two nonadiabatic hypersonic shock-wave boundary-layer interaction flows, one with and one without separation. These measurements were obtained using a new hot-wire probe specially designed for heated flows. Comparison of the separated and attached flows shows a significant increase above equilibrium values in the turbulent intensity and shear stress downstream of the interaction region for the attached case, while for the separated case, the turbulent fluxes remain close to equilibrium values. This effect results in substantial differences in turbulence lifetimes for the two flows. It is proposed that these differences are due to a coupling between the turbulent energy and separation bubble unsteadiness, a hypothesis supported by the statistical properties of the turbulent fluctuations.

Models of determining deformations

NASA Astrophysics Data System (ADS)

Gladilin, V. N.

2016-12-01

In recent years, a lot of functions designed to determine deformation values that occur mostly as a result of settlement of structures and industrial equipment. Some authors suggest such advanced mathematical functions approximating deformations as general methods for the determination of deformations. The article describes models of deformations as physical processes. When comparing static, cinematic and dynamic models, it was found that the dynamic model reflects the deformation of structures and industrial equipment most reliably.

Shock-induced bubble collapse in a vessel: Implications for vascular injury in shockwave lithotripsy

NASA Astrophysics Data System (ADS)

Coralic, Vedran; Colonius, Tim

2014-11-01

In shockwave lithotripsy, shocks are repeatedly focused on kidney stones so to break them. The process leads to cavitation in tissue, which leads to hemorrhage. We hypothesize that shock-induced collapse (SIC) of preexisting bubbles is a potential mechanism for vascular injury. We study it numerically with an idealized problem consisting of the three-dimensional SIC of an air bubble immersed in a cylindrical water column embedded in gelatin. The gelatin is a tissue simulant and can be treated as a fluid due to fast time scales and small spatial scales of collapse. We thus model the problem as a compressible multicomponent flow and simulate it with a shock- and interface-capturing numerical method. The method is high-order, conservative and non-oscillatory. Fifth-order WENO is used for spatial reconstruction and an HLLC Riemann solver upwinds the fluxes. A third-order TVD-RK scheme evolves the solution. We evaluate the potential for injury in SIC for a range of pressures, bubble and vessel sizes, and tissue properties. We assess the potential for injury by comparing the finite strains in tissue, obtained by particle tracking, to ultimate strains from experiments. We conclude that SIC may contribute to vascular rupture and discuss the smallest bubble sizes needed for injury. This research was supported by NIH Grant No. 2PO1DK043881 and utilized XSEDE, which is supported by NSF Grant No. OCI-1053575.

A rough end for smooth microstate geometries

DOE PAGES

Marolf, Donald; Michel, Ben; Puhm, Andrea

2017-05-03

Supersymmetric microstate geometries with five non-compact dimensions have recently been shown by Eperon, Reall, and Santos (ERS) to exhibit a non-linear instability featuring the growth of excitations at an “evanescent ergosurface” of infinite redshift. We argue that this growth may be treated as adiabatic evolution along a family of exactly supersymmetric solutions in the limit where the excitations are Aichelburg-Sexl-like shockwaves. In the 2-charge system such solutions may be constructed explicitly, incorpo-rating full backreaction, and are in fact special cases of known microstate geometries. In a near-horizon limit, they reduce to Aichelburg-Sexl shockwaves in AdS 3 × S 3 propagatingmore » along one of the angular directions of the sphere. Noting that the ERS analysis is valid in the limit of large microstate angular momentum j, we use the above identification to interpret their instability as a transition from rare smooth microstates with large angular momentum to more typical microstates with smaller angular momentum. This entropic driving terminates when the angular momentum decreases to j~√n 1n 5 where the density of microstates is maximal. Finally, we argue that, at this point, the large stringy corrections to such microstates will render them non-linearly stable. We identify a possible mechanism for this stabilization and detail an illustrative toy model.« less

Extracorporeal low-energy shock-wave therapy exerts anti-inflammatory effects in a rat model of acute myocardial infarction.

PubMed

Abe, Yuzuru; Ito, Kenta; Hao, Kiyotaka; Shindo, Tomohiko; Ogata, Tsuyoshi; Kagaya, Yuta; Kurosawa, Ryo; Nishimiya, Kensuke; Satoh, Kimio; Miyata, Satoshi; Kawakami, Kazuyoshi; Shimokawa, Hiroaki

2014-01-01

It has been previously demonstrated that extracorporeal low-energy shock-wave (SW) therapy ameliorates left ventricular (LV) remodeling through enhanced angiogenesis after acute myocardial infarction (AMI) in pigs in vivo. However, it remains to be examined whether SW therapy also exerts anti-inflammatory effects on AMI. METHODS AND RESULTS: AMI was created by ligating the proximal left anterior descending coronary artery in rats. They were randomly assigned to 2 groups: with (SW group) or without (control group) SW therapy (0.1 mJ/mm(2), 200 shots, 1 Hz to the whole heart at 1, 3 and 5 days after AMI). Four weeks after AMI, SW therapy significantly ameliorated LV remodeling and fibrosis. Histological examinations showed that SW therapy significantly suppressed the infiltration of neutrophils and macrophages at days 3 and 6, in addition to enhanced capillary density in the border area. Molecular examinations demonstrated that SW therapy enhanced the expression of endothelial nitric oxide synthase and suppressed the infiltration of transforming growth factor-β1-positive cells early after AMI. SW therapy also upregulated anti-inflammatory cytokines and downregulated pro-inflammatory cytokines in general. These results suggest that low-energy SW therapy suppressed post-MI LV remodeling in rats in vivo, which was associated with anti-inflammatory effects in addition to its angiogenic effects, and demonstrated a novel aspect of the therapy for AMI.

Chelyabinsk meteoroid entry and airburst damage

NASA Astrophysics Data System (ADS)

Popova, Olga; Emel'yanenko, Vacheslav; Kartashova, Anna; Rybnov, Yurij; Shuvalov, Valery; Jenniskens, Peter; Kharlamov, Vladimir

The Chelyabinsk airburst of 15 February 2013, was exceptional because of the large kinetic energy of the impacting body and the airburst that was generated, which created significant damage on the ground and numerous injuries in a populated area. The meteor and the effects of the airburst were extraordinarily well documented. Other events with comparable or larger energy in the past century or so include the 1963 August 3 bolide over the south Atlantic, for which only an infrasound signal was recorded, and the famous Tunguska impact in 1908. Estimates of the kinetic energy of the Tunguska impact range from 3 to 50 Mt, due to a lack of good observations at the time. The Chelyabinsk event is much better documented than both, and provides a unique opportunity to calibrate the different approaches used to model meteoroid entry and calculate the damaging effects of its airburst. Being able to predict better the potential damage on the ground from an impending small asteroid impact will help future impact hazard mitigation efforts. In order to be able to model the damaging effects of the Chelyabinsk airburst, the initial kinetic energy and approach trajectory needed to be known, how that energy was dissipated in the atmosphere, and what were the properties of the resulting airburst shockwave. Infrasonic waves are an important source of information about the fireball's initial kinetic energy. Further information about the kinetic energy is derived from the fireball's light curve. Analysis of video observations of the fireball and the shadows movements provided a meteor light curve, deceleration curve and trajectory. Video records also provided time of arrivals of the shockwave and much detail about how that shockwave interacted with surface structures. The extent of the glass damage was mapped by visiting over 50 villages in the area. Meteorites were analysed in a consortium study to understand how their material properties may have contributed to the fragmentation process. As a first attempt to understand what happened, numerical models were developed to reproduce the observed bolide light curve and the deceleration profile, which include the effects of ablation and fragmentation. We conclude that meteoroid fragmentation occurred in different forms. Some part of the initial mass broke in fragments well enough separated so that they were efficiently slowed down. A number of numerical simulations were conducted that attempted a realistic release of energy along the trajectory and these results were compared with observations of blast wave arrival times and the extent of the glass damage. The shape of the damaged area could be explained from the fact that the energy was deposited over a range of altitudes.

Flow characteristics around a deformable stenosis under pulsatile flow condition

NASA Astrophysics Data System (ADS)

Choi, Woorak; Park, Jun Hong; Byeon, Hyeokjun; Lee, Sang Joon

2018-01-01

A specific portion of a vulnerable stenosis is deformed periodically under a pulsatile blood flow condition. Detailed analysis of such deformable stenosis is important because stenotic deformation can increase the likelihood of rupture, which may lead to sudden cardiac death or stroke. Various diagnostic indices have been developed for a nondeformable stenosis by using flow characteristics and resultant pressure drop across the stenosis. However, the effects of the stenotic deformation on the flow characteristics remain poorly understood. In this study, the flows around a deformable stenosis model and two different rigid stenosis models were investigated under a pulsatile flow condition. Particle image velocimetry was employed to measure flow structures around the three stenosis models. The deformable stenosis model was deformed to achieve high geometrical slope and height when the flow rate was increased. The deformation of the stenotic shape enhanced jet deflection toward the opposite vessel wall of the stenosis. The jet deflection in the deformable model increased the rate of jet velocity and turbulent kinetic energy (TKE) production as compared with those in the rigid models. The effect of stenotic deformation on the pulsating waveform related with the pressure drop was analyzed using the TKE production rate. The deformable stenosis model exhibited a phase delay of the peak point in the waveform. These results revealed the potential use of pressure drop waveform as a diagnostic index for deformable stenosis.

Magnetic Fields and Bow Shocks Illustration

NASA Image and Video Library

2013-02-19

This illustration shows quasi-parallel top and quasi-perpendicular bottom magnetic field conditions at a planetary bow shock. Bow shocks are shockwaves created when the solar wind blows on a planet magnetic field.

Completely explosive ultracompact high-voltage nanosecond pulse-generating system

NASA Astrophysics Data System (ADS)

Shkuratov, Sergey I.; Talantsev, Evgueni F.; Baird, Jason; Rose, Millard F.; Shotts, Zachary; Altgilbers, Larry L.; Stults, Allen H.

2006-04-01

A conventional pulsed power technology has been combined with an explosive pulsed power technology to produce an autonomous high-voltage power supply. The power supply contained an explosive-driven high-voltage primary power source and a power-conditioning stage. The ultracompact explosive-driven primary power source was based on the physical effect of shock-wave depolarization of high-energy Pb (Zr52Ti48)O3 ferroelectric material. The volume of the energy-carrying ferroelectric elements in the shock-wave ferroelectric generators (SWFEGs) varied from 1.2 to 2.6cm3. The power-conditioning stage was based on the spiral vector inversion generator (VIG). The SWFEG-VIG system demonstrated successful operation and good performance. The amplitude of the output voltage pulse of the SWFEG-VIG system exceeded 90kV, with a rise time of 5.2ns.

Laser Shockwave Technique For Characterization Of Nuclear Fuel Plate Interfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

James A. Smith; Barry H. Rabin; Mathieu Perton

2012-07-01

The US National Nuclear Security Agency is tasked with minimizing the worldwide use of high-enriched uranium. One aspect of that effort is the conversion of research reactors to monolithic fuel plates of low-enriched uranium. The manufacturing process includes hot isostatic press bonding of an aluminum cladding to the fuel foil. The Laser Shockwave Technique (LST) is here evaluated for characterizing the interface strength of fuel plates using depleted Uranium/Mo foils. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves and is therefore well adapted to the quality assurance of this process.more » Preliminary results show a clear signature of well-bonded and debonded interfaces and the method is able to classify/rank the bond strength of fuel plates prepared under different HIP conditions.« less

Laser shockwave technique for characterization of nuclear fuel plate interfaces

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perton, M.; Levesque, D.; Monchalin, J.-P.

2013-01-25

The US National Nuclear Security Agency is tasked with minimizing the worldwide use of high-enriched uranium. One aspect of that effort is the conversion of research reactors to monolithic fuel plates of low-enriched uranium. The manufacturing process includes hot isostatic press bonding of an aluminum cladding to the fuel foil. The Laser Shockwave Technique (LST) is here evaluated for characterizing the interface strength of fuel plates using depleted Uranium/Mo foils. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves and is therefore well adapted to the quality assurance of this process.more » Preliminary results show a clear signature of well-bonded and debonded interfaces and the method is able to classify/rank the bond strength of fuel plates prepared under different HIP conditions.« less

Fabrication and application of a carbon nanotube/poly(dimethylsiloxane) coated optoacoustic film transducer

NASA Astrophysics Data System (ADS)

Fan, Xiaofeng; Ha, Kanglyeol; Kim, Moojoon; Kang, Gwansuk; Choi, Min Joo; Oh, Junghwan

2018-07-01

An optoacoustic film transducer was fabricated by coating carbon nanotubes (CNTs) and poly(dimethylsiloxane) (PDMS) on the surface of a thin flexible optical poly(ethylene terephthalate) (PET) sheet. When a laser pulse was irradiated on the film transducer, a shockwave, with superimposed waves reflected from the surface and the back of the film, was generated. The shockwave had very small pulse widths of 20–30 ns, and the maximum pressure of 5.4 MPa was obtained at 10 mm from the surface of the transducer. A line-focused optoacoustic source was fabricated using the film transducer, and its characteristics were investigated. A very high maximum pressure of about 35 MPa was obtained using the source. It was demonstrated that the source can engrave a line trace on a chalk surface.

Single center, single operator comparative study of the effectiveness of electrohydraulic and electromagnetic lithotripters in the management of 10- to 20-mm single upper urinary tract calculi.

PubMed

Jamshaid, Anila; Ather, M Hammad; Hussain, Ghazi; Khawaja, Karim B

2008-11-01

This study compared the efficacy and safety profile of electrohydraulic (EH) and electromagnetic (EM) lithotriptors in the treatment of 10- to 20-mm renal and proximal ureteric stones at a single center and by a single operator. Between January 2001 and December 2006, we sequentially treated patients meeting study inclusion criteria with MPL 9000 Dornier EH for the first 3 years, followed by the EM Siemens Modularis shockwave lithotripsy (SWL) unit. A single operator performed all SWL treatments under the supervision of an admitting urologist. We analyzed the demographic features and stone- and treatment-related parameters including complications for both groups. In each group, the stone-free rate and efficiency quotient was determined at 1-3 months. Of 274 patients, we sequentially treated 112 using the EH lithotriptor, and 162 the EM lithotriptor. The pre-SWL patients and stone-related parameters were similar in the two groups, except for diagnostic imaging modalities. The mean number of SWL sessions, need for ancillary procedure, retreatment rate, stone location, stone-free rate, and efficiency quotient were not significantly different between groups. The mean number of shockwaves required for complete fragmentation was 2977 and 6044 (P < .000) for the EH and EM groups, respectively. Single center, single operator experience with two types of lithotriptor indicated that both are equally efficacious, with similar safety profiles. The only significant difference was that the EH lithotriptor required fewer shockwaves for fragmentation.

Optimizing results of lithotripsy using robust electromagnetic probe.

PubMed

Keeley, F X; Pye, S D; Smith, G; Tolley, D A

1999-05-01

A significant impediment to the measurement of the pressures and forces created by lithotripter shockwaves has been their destructive properties, which have rendered most measuring devices impractical. We have developed and tested a robust electromagnetic probe to measure cavitational forces in vitro in the focal zones of extracorporeal lithotripters. The probe responds to the pressure gradient generated by the radial motion of cavitation bubbles. The effects of shockwaves from the Dornier MPL 9000 electrohydraulic lithotripter were measured over the lifetime of multiple electrodes. The pulse energy from the electrodes dropped off rapidly after approximately 50% of the lifetime quoted by the manufacturer. The electrodes were more efficient at higher power settings. As a result, we altered our protocol for the treatment of ureteral stones to use a higher kilovoltage and a second electrode whenever necessary. Stone-free rates after shockwave lithotripsy (SWL) in situ for stones < 11 mm have increased from 68.2% to 83.3%, and the retreatment rate has dropped from 23% to 15%. Despite significantly higher power settings (23.7 kV v 18.7 kV; P < 0.0001), the need for sedoanalgesia has remained relatively constant (26% v 31%). Measurement of cavitational forces from lithotripters using a robust electromagnetic probe is useful in planning treatment strategy. We have demonstrated a clinically measurable improvement since implementing our new treatment protocol. Because the probe responds directly to cavitational forces, it should also prove useful for the objective comparison of different SWL machines.

Focused extracorporeal shockwave therapy in Dupuytren's disease--a hypothesis.

PubMed

Knobloch, Karsten; Kuehn, Marie; Vogt, Peter M

2011-05-01

Dupuytren's disease is a progressive disease due to unknown causal agents or genetics. An epidemiological analysis of 566 cases in North Germany estimated that around 1.9 million Germans are suffering from Dupuytren's disease. Beside Dupuytren's disease, there are a number of further less common forms of progressive fibromatosis, such as knuckle pads, plantar fibromatosis or Peyronie's disease. Surgery in plantar fasciectomy yields to a 60% recurrence rate depending on the extent of the plantar fasciectomy. Peyronie's disease of the penis affects middle-aged men between 40 and 60 years with penile pain, curvature during erection and potential erectile dysfunction. In a clinical randomized-controlled trial in Peyronie's disease 2000 focused extracorporeal shock waves reduced pain significantly and improved erectile function and quality of life. We hypothesize that focused extracorporeal shock wave therapy is able to reduce Dupuytren's contracture, a fibromatosis of the palm and improve function. Given the fact that recurrence rate in Dupuytren's disease is high und unpredictable extracorporeal shockwave therapy as a non-invasive tool might be applicable both, in primary and secondary prevention of the progression as well as for treatment. As such we have planned a randomized-controlled trial (ClinicialTrials.gov, NCT01184586) studying the effect of high-energy focused extracorporeal shockwave therapy on patients suffering Dupuytren's disease with patient-related outcome measures such as the DASH score and the Michigan Hand Outcome Questionnaire (MHQ) as primary outcome parameters. Copyright © 2011 Elsevier Ltd. All rights reserved.

The Resistance to Deformation and Facture of Magnesium MA2-1 Under Shock-Wave Loading at 293 K and 823 K of the Temperature

NASA Astrophysics Data System (ADS)

Garkushin, Gennady; Kanel, Gennady; Razorenov, Sergey

2011-06-01

The spall strength and elastic-plastic response have been measured with the VISAR for MA2-1 (94.2% Mg, 0.4 % Mn, 4.4% Al, 1% Zn) alloy at temperatures from 293 K to 823 K. The decay of elastic precursor wave at 293 K is approximately in reverse proportionality with the cubic root from the distance that corresponds to decrease of plastic strain rate from 5 ×105 s-1 at 0.25 mm (213 MPa of the shear stress) down to 5 ×103 s-1 at 10 mm (63 MPa shear stress). An analysis of the rise times of plastic shock waves shows by order of magnitude faster plastic strain rates at corresponding shear stresses than that at the HEL. The decay of elastic precursor wave is weaker and the dependence of initial plastic strain rate on the shear stress at HEL is stronger than that was observed for aluminum. Unlike to aluminum, the magnesium alloy does not exhibit anomalous thermal hardening: the HEL values at 823 K are close to the values at room temperatures. The temperature increase from 293 K to 823 K has led to significant decrease of the spall strength.

Computer program to solve two-dimensional shock-wave interference problems with an equilibrium chemically reacting air model

NASA Technical Reports Server (NTRS)

Glass, Christopher E.

1990-01-01

The computer program EASI, an acronym for Equilibrium Air Shock Interference, was developed to calculate the inviscid flowfield, the maximum surface pressure, and the maximum heat flux produced by six shock wave interference patterns on a 2-D, cylindrical configuration. Thermodynamic properties of the inviscid flowfield are determined using either an 11-specie, 7-reaction equilibrium chemically reacting air model or a calorically perfect air model. The inviscid flowfield is solved using the integral form of the conservation equations. Surface heating calculations at the impingement point for the equilibrium chemically reacting air model use variable transport properties and specific heat. However, for the calorically perfect air model, heating rate calculations use a constant Prandtl number. Sample calculations of the six shock wave interference patterns, a listing of the computer program, and flowcharts of the programming logic are included.

Computer program to solve two-dimensional shock-wave interference problems with an equilibrium chemically reacting air model

NASA Astrophysics Data System (ADS)

Glass, Christopher E.

1990-08-01

The computer program EASI, an acronym for Equilibrium Air Shock Interference, was developed to calculate the inviscid flowfield, the maximum surface pressure, and the maximum heat flux produced by six shock wave interference patterns on a 2-D, cylindrical configuration. Thermodynamic properties of the inviscid flowfield are determined using either an 11-specie, 7-reaction equilibrium chemically reacting air model or a calorically perfect air model. The inviscid flowfield is solved using the integral form of the conservation equations. Surface heating calculations at the impingement point for the equilibrium chemically reacting air model use variable transport properties and specific heat. However, for the calorically perfect air model, heating rate calculations use a constant Prandtl number. Sample calculations of the six shock wave interference patterns, a listing of the computer program, and flowcharts of the programming logic are included.

Supersonic projectile models for asynchronous shooter localization

NASA Astrophysics Data System (ADS)

Kozick, Richard J.; Whipps, Gene T.; Ash, Joshua N.

2011-06-01

In this work we consider the localization of a gunshot using a distributed sensor network measuring time differences of arrival between a firearm's muzzle blast and the shockwave induced by a supersonic bullet. This so-called MB-SW approach is desirable because time synchronization is not required between the sensors, however it suffers from increased computational complexity and requires knowledge of the bullet's velocity at all points along its trajectory. While the actual velocity profile of a particular gunshot is unknown, one may use a parameterized model for the velocity profile and simultaneously fit the model and localize the shooter. In this paper we study efficient solutions for the localization problem and identify deceleration models that trade off localization accuracy and computational complexity. We also develop a statistical analysis that includes bias due to mismatch between the true and actual deceleration models and covariance due to additive noise.

Numerical Investigations on Aerodynamic Forces of Deformable Foils in Hovering Motions

NASA Astrophysics Data System (ADS)

Zhao, Yong; Yin, Zhen; Su, Xiaohui; Zhang, Jiantao; Cao, Yuanwei

2017-09-01

The aerodynamic effects of wing deformation for hover flight are numerically investigated by a two-dimensional finite-volume (FV) Arbitrary Langrangian Eulerian (ALE) Navier-Stokes solver. Two deformation models are employed to study these effects in this paper, which are a full deformation model and a partial deformation one. Attentions are paid to the generation and development of leading edge vortex (LEV) and trailing edge vortex (TEV) which may illustrate the differences of lift force generation mechanisms from those of rigid wings. Moreover, lift coefficient Cl, drag coefficient Cd, and figure of merit, as well as energy consumption in hovering motion for different deformation foil models, are also studied. The results show that the deformed amplitude, 0.1*chord, among the cases simulated is an optimized camber amplitude for full deformation. The results obtained from the partial deformation foil model show that both Cl and Cd decrease with the increase of camber amplitude. It is found that the effect of deformation in the partial deformation model does not enhance lift force due to unfavorable camber. But TEV is significantly changed by the local AOA due to the deformation of the foil. Introduction.

Particle-based simulations of bilayer membranes: self-assembly, structural analysis, and shock-wave damage

NASA Astrophysics Data System (ADS)

Steinhauser, Martin O.; Schindler, Tanja

2017-01-01

We report on the results of particle-based, coarse-grained molecular dynamics simulations of amphiphilic lipid molecules in aqueous environment where the membrane structures at equilibrium are subsequently exposed to strong shock waves, and their damage is analyzed. The lipid molecules self-assemble from unbiased random initial configurations to form stable bilayer membranes, including closed vesicles. During self-assembly of lipid molecules, we observe several stages of clustering, starting with many small clusters of lipids, gradually merging together to finally form one single bilayer membrane. We find that the clustering of lipids sensitively depends on the hydrophobic interaction h_c of the lipid tails in our model and on temperature T of the system. The self-assembled bilayer membranes are quantitatively analyzed at equilibrium with respect to their degree of order and their local structure. We also show that—by analyzing the membrane fluctuations and using a linearized theory— we obtain area compression moduli K_A and bending stiffnesses κ _B for our bilayer membranes which are within the experimental range of in vivo and in vitro measurements of biological membranes. We also discuss the density profile and the pair correlation function of our model membranes at equilibrium which has not been done in previous studies of particle-based membrane models. Furthermore, we present a detailed phase diagram of our lipid model that exhibits a sol-gel transition between quasi-solid and fluid domains, and domains where no self-assembly of lipids occurs. In addition, we present in the phase diagram the conditions for temperature T and hydrophobicity h_c of the lipid tails of our model to form closed vesicles. The stable bilayer membranes obtained at equilibrium are then subjected to strong shock waves in a shock tube setup, and we investigate the damage in the membranes due to their interaction with shock waves. Here, we find a transition from self-repairing membranes (reducing their damage after impact) and permanent (irreversible) damage, depending on the shock front speed. The here presented idea of using coarse-grained (CG) particle models for soft matter systems in combination with the investigation of shock-wave effects in these systems is a quite new approach.

Experimental constraints on the sulfur content in the Earth's core

NASA Astrophysics Data System (ADS)

Fei, Y.; Huang, H.; Leng, C.; Hu, X.; Wang, Q.

2015-12-01

Any core formation models would lead to the incorporation of sulfur (S) into the Earth's core, based on the cosmochemical/geochemical constraints, sulfur's chemical affinity for iron (Fe), and low eutectic melting temperature in the Fe-FeS system. Preferential partitioning of S into the melt also provides petrologic constraint on the density difference between the liquid outer and solid inner cores. Therefore, the center issue is to constrain the amount of sulfur in the core. Geochemical constraints usually place 2-4 wt.% S in the core after accounting for its volatility, whereas more S is allowed in models based on mineral physics data. Here we re-examine the constraints on the S content in the core by both petrologic and mineral physics data. We have measured S partitioning between solid and liquid iron in the multi-anvil apparatus and the laser-heated diamond anvil cell, evaluating the effect of pressure on melting temperature and partition coefficient. In addition, we have conducted shockwave experiments on Fe-11.8wt%S using a two-stage light gas gun up to 211 GPa. The new shockwave experiments yield Hugoniot densities and the longitudinal sound velocities. The measurements provide the longitudinal sound velocity before melting and the bulk sound velocity of liquid. The measured sound velocities clearly show melting of the Fe-FeS mix with 11.8wt%S at a pressure between 111 and 129 GPa. The sound velocities at pressures above 129GPa represent the bulk sound velocities of Fe-11.8wt%S liquid. The combined data set including density, sound velocity, melting temperature, and S partitioning places a tight constraint on the required sulfur partition coefficient to produce the density and velocity jumps and the bulk sulfur content in the core.

Heterogeneous Deformable Modeling of Bio-Tissues and Haptic Force Rendering for Bio-Object Modeling

NASA Astrophysics Data System (ADS)

Lin, Shiyong; Lee, Yuan-Shin; Narayan, Roger J.

This paper presents a novel technique for modeling soft biological tissues as well as the development of an innovative interface for bio-manufacturing and medical applications. Heterogeneous deformable models may be used to represent the actual internal structures of deformable biological objects, which possess multiple components and nonuniform material properties. Both heterogeneous deformable object modeling and accurate haptic rendering can greatly enhance the realism and fidelity of virtual reality environments. In this paper, a tri-ray node snapping algorithm is proposed to generate a volumetric heterogeneous deformable model from a set of object interface surfaces between different materials. A constrained local static integration method is presented for simulating deformation and accurate force feedback based on the material properties of a heterogeneous structure. Biological soft tissue modeling is used as an example to demonstrate the proposed techniques. By integrating the heterogeneous deformable model into a virtual environment, users can both observe different materials inside a deformable object as well as interact with it by touching the deformable object using a haptic device. The presented techniques can be used for surgical simulation, bio-product design, bio-manufacturing, and medical applications.

Deformations of the Almheiri-Polchinski model

NASA Astrophysics Data System (ADS)

Kyono, Hideki; Okumura, Suguru; Yoshida, Kentaroh

2017-03-01

We study deformations of the Almheiri-Polchinski (AP) model by employing the Yang-Baxter deformation technique. The general deformed AdS2 metric becomes a solution of a deformed AP model. In particular, the dilaton potential is deformed from a simple quadratic form to a hyperbolic function-type potential similarly to integrable deformations. A specific solution is a deformed black hole solution. Because the deformation makes the spacetime structure around the boundary change drastically and a new naked singularity appears, the holographic interpretation is far from trivial. The Hawking temperature is the same as the undeformed case but the Bekenstein-Hawking entropy is modified due to the deformation. This entropy can also be reproduced by evaluating the renormalized stress tensor with an appropriate counter-term on the regularized screen close to the singularity.

Evaluation of transtension and transpression within contractional fault steps: Comparing kinematic and mechanical models to field data

NASA Astrophysics Data System (ADS)

Nevitt, Johanna M.; Pollard, David D.; Warren, Jessica M.

2014-03-01

Rock deformation often is investigated using kinematic and/or mechanical models. Here we provide a direct comparison of these modeling techniques in the context of a deformed dike within a meter-scale contractional fault step. The kinematic models consider two possible shear plane orientations and various modes of deformation (simple shear, transtension, transpression), while the mechanical model uses the finite element method and assumes elastoplastic constitutive behavior. The results for the kinematic and mechanical models are directly compared using the modeled maximum and minimum principal stretches. The kinematic analysis indicates that the contractional step may be classified as either transtensional or transpressional depending on the modeled shear plane orientation, suggesting that these terms may be inappropriate descriptors of step-related deformation. While the kinematic models do an acceptable job of depicting the change in dike shape and orientation, they are restricted to a prescribed homogeneous deformation. In contrast, the mechanical model allows for heterogeneous deformation within the step to accurately represent the deformation. The ability to characterize heterogeneous deformation and include fault slip - not as a prescription, but as a solution to the governing equations of motion - represents a significant advantage of the mechanical model over the kinematic models.

Patterns of Alloy Deformation by Pulsed Pressure

NASA Astrophysics Data System (ADS)

Chebotnyagin, L. M.; Potapov, V. V.; Lopatin, V. V.

2015-06-01

Patterns of alloy deformation for optimization of a welding regime are studied by the method of modeling and deformation profiles providing high deformation quality are determined. A model of stepwise kinetics of the alloy deformation by pulsed pressure from the expanding plasma channel inside of a deformable cylinder is suggested. The model is based on the analogy between the acoustic and electromagnetic wave processes in long lines. The shock wave pattern of alloy deformation in the presence of multiple reflections of pulsed pressure waves in the gap plasma channel - cylinder wall and the influence of unloading waves from free surfaces are confirmed.

Soft tissue modelling with conical springs.

PubMed

Omar, Nadzeri; Zhong, Yongmin; Jazar, Reza N; Subic, Aleksandar; Smith, Julian; Shirinzadeh, Bijan

2015-01-01

This paper presents a new method for real-time modelling soft tissue deformation. It improves the traditional mass-spring model with conical springs to deal with nonlinear mechanical behaviours of soft tissues. A conical spring model is developed to predict soft tissue deformation with reference to deformation patterns. The model parameters are formulated according to tissue deformation patterns and the nonlinear behaviours of soft tissues are modelled with the stiffness variation of conical spring. Experimental results show that the proposed method can describe different tissue deformation patterns using one single equation and also exhibit the typical mechanical behaviours of soft tissues.

A Supernova Shockwaves

NASA Image and Video Library

2007-06-13

Supernovae are the explosive deaths of the universe most massive stars. This false-color composite from NASA Spitzer Space Telescope and NASA Chandra X-ray Observatory shows the remnant of N132D, the wispy pink shell of gas at center.

Influence of shockwave profile on ejecta: An experimental and computational study

NASA Astrophysics Data System (ADS)

Zellner, Michael; Germann, Timothy; Hammerberg, James; Rigg, Paulo; Stevens, Gerald; Turley, William; Buttler, William

2009-06-01

This effort investigates the relation between shock-pulse shape and the amount of micron-scale fragments ejected (ejecta) upon shock release at the metal/vacuum interface of shocked Sn targets. Two shock-pulse shapes are considered: a supported shock created by impacting a Sn target with a sabot that was accelerated using a powder gun; and an unsupported or Taylor shockwave, created by detonation of high explosive that was press-fit to the front-side of the Sn target. Ejecta production at the back-side or free-side of the Sn coupons were characterized through use of piezoelectric pins, Asay foils, optical shadowgraph, and x-ray attenuation. In addition to the experimental results, SPaSM, a short-ranged parallel molecular dynamics code developed at Los Alamos National Laboratory, was used to investigate the relation between shock-pulse shape and production of ejecta from a first principles point-of-view.

Preliminary Investigation on the Effects of Shockwaves on Water Samples Using a Portable Semi-Automatic Shocktube

NASA Astrophysics Data System (ADS)

Wessley, G. Jims John

2017-10-01

The propagation of shock waves through any media results in an instantaneous increase in pressure and temperature behind the shockwave. The scope of utilizing this sudden rise in pressure and temperature in new industrial, biological and commercial areas has been explored and the opportunities are tremendous. This paper presents the design and testing of a portable semi-automatic shock tube on water samples mixed with salt. The preliminary analysis shows encouraging results as the salinity of water samples were reduced up to 5% when bombarded with 250 shocks generated using a pressure ratio of 2. 5. Paper used for normal printing is used as the diaphragm to generate the shocks. The impact of shocks of much higher intensity obtained using different diaphragms will lead to more reduction in the salinity of the sea water, thus leading to production of potable water from saline water, which is the need of the hour.

Optical pin apparatus for measuring the arrival time and velocity of shock waves and particles

DOEpatents

Benjamin, R.F.

1983-10-18

An apparatus for the detection of the arrival and for the determination of the velocity of disturbances such as shock-wave fronts and/or projectiles. Optical pins using fluid-filled microballoons as the light source and an optical fiber as a link to a photodetector have been used to investigate shock-waves and projectiles. A microballoon filled with a noble gas is affixed to one end of a fiber-optic cable, and the other end of the cable is attached to a high-speed streak camera. As the shock-front or projectile compresses the microballoon, the gas inside is heated and compressed producing a bright flash of light. The flash of light is transmitted via the optic cable to the streak camera where it is recorded. One image-converter streak camera is capable of recording information from more than 100 microballoon-cable combinations simultaneously.

The efficacy of radiographic anatomical measurement methods in predicting success after extracorporeal shockwave lithotripsy for lower pole kidney stones.

PubMed

Arpali, Emre; Altinel, Mert; Sargin, Semih Yasar

2014-01-01

To assess the impact of lower pole calyceal anatomy on clearace of lower pole stones after extracorporeal shockwave lithotripsy (ESWL) by means of a new and previously defined radiographic measurement method. Sixty-four patients with solitary radiopaque lower pole kidney stones were enrolled in the study. Infundibulopelvic angle (IPA), infundibulotransverse angle (ITA), infundibular lenght(IL), and infundibular width (IW) were measured on the intravenous urographies which were taken before the procedure. 48 of 64 patients (75%) were stone-free after a follow-up period of 3 months. The IPA,ITA,IL and IW were determined as statistically significant factors, while age,gender and stone area were found to have no impact on clearance. By the help of radiographic measurement methods related to lower pole kidney anatomy, appropriate patient selection and increment in success after ESWL may be achieved.

Ultrafast collisional ion heating by electrostatic shocks.

PubMed

Turrell, A E; Sherlock, M; Rose, S J

2015-11-13

High-intensity lasers can be used to generate shockwaves, which have found applications in nuclear fusion, proton imaging, cancer therapies and materials science. Collisionless electrostatic shocks are one type of shockwave widely studied for applications involving ion acceleration. Here we show a novel mechanism for collisionless electrostatic shocks to heat small amounts of solid density matter to temperatures of ∼keV in tens of femtoseconds. Unusually, electrons play no direct role in the heating and it is the ions that determine the heating rate. Ions are heated due to an interplay between the electric field of the shock, the local density increase during the passage of the shock and collisions between different species of ion. In simulations, these factors combine to produce rapid, localized heating of the lighter ion species. Although the heated volume is modest, this would be one of the fastest heating mechanisms discovered if demonstrated in the laboratory.

On the possibility of using multi-element phased arrays for shock-wave action on deep brain structures

NASA Astrophysics Data System (ADS)

Rosnitskiy, P. B.; Gavrilov, L. R.; Yuldashev, P. V.; Sapozhnikov, O. A.; Khokhlova, V. A.

2017-09-01

A noninvasive ultrasound surgery method that relies on using multi-element focused phased arrays is being successfully used to destroy tumors and perform neurosurgical operations in deep structures of the human brain. However, several drawbacks that limit the possibilities of the existing systems in their clinical use have been revealed: a large size of the hemispherical array, impossibility of its mechanical movement relative to the patient's head, limited volume of dynamic focusing around the center of curvature of the array, and side effect of overheating skull. Here we evaluate the possibility of using arrays of smaller size and aperture angles to achieve shock-wave formation at the focus for thermal and mechanical ablation (histotripsy) of brain tissue taking into account current intensity limitations at the array elements. The proposed approach has potential advantages to mitigate the existing limitations and expand the possibilities of transcranial ultrasound surgery.

Optical pin apparatus for measuring the arrival time and velocity of shock waves and particles

DOEpatents

Benjamin, Robert F.

1987-01-01

An apparatus for the detection of the arrival and for the determination of the velocity of disturbances such as shock-wave fronts and/or projectiles. Optical pins using fluid-filled microballoons as the light source and an optical fiber as a link to a photodetector have been used to investigate shock-waves and projectiles. A microballoon filled with a noble gas is affixed to one end of a fiber-optic cable, and the other end of the cable is attached to a high-speed streak camera. As the shock-front or projectile compresses the microballoon, the gas inside is heated and compressed producing a bright flash of light. The flash of light is transmitted via the optic cable to the streak camera where it is recorded. One image-converter streak camera is capable of recording information from more than 100 microballoon-cable combinations simultaneously.

Optical pin apparatus for measuring the arrival time and velocity of shock waves and particles

DOEpatents

Benjamin, R.F.

1987-03-10

An apparatus is disclosed for the detection of the arrival and for the determination of the velocity of disturbances such as shock-wave fronts and/or projectiles. Optical pins using fluid-filled microballoons as the light source and an optical fiber as a link to a photodetector have been used to investigate shock-waves and projectiles. A microballoon filled with a noble gas is affixed to one end of a fiber-optic cable, and the other end of the cable is attached to a high-speed streak camera. As the shock-front or projectile compresses the microballoon, the gas inside is heated and compressed producing a bright flash of light. The flash of light is transmitted via the optic cable to the streak camera where it is recorded. One image-converter streak camera is capable of recording information from more than 100 microballoon-cable combinations simultaneously. 3 figs.

DOE Office of Scientific and Technical Information (OSTI.GOV)

James A. Smith; Jeffrey M. Lacy; Barry H. Rabin

12. Other advances in QNDE and related topics: Preferred Session Laser-ultrasonics Developing A Laser Shockwave Model For Characterizing Diffusion Bonded Interfaces 41st Annual Review of Progress in Quantitative Nondestructive Evaluation Conference QNDE Conference July 20-25, 2014 Boise Centre 850 West Front Street Boise, Idaho 83702 James A. Smith, Jeffrey M. Lacy, Barry H. Rabin, Idaho National Laboratory, Idaho Falls, ID ABSTRACT: The US National Nuclear Security Agency has a Global Threat Reduction Initiative (GTRI) which is assigned with reducing the worldwide use of high-enriched uranium (HEU). A salient component of that initiative is the conversion of research reactors from HEUmore » to low enriched uranium (LEU) fuels. An innovative fuel is being developed to replace HEU. The new LEU fuel is based on a monolithic fuel made from a U-Mo alloy foil encapsulated in Al-6061 cladding. In order to complete the fuel qualification process, the laser shock technique is being developed to characterize the clad-clad and fuel-clad interface strengths in fresh and irradiated fuel plates. The Laser Shockwave Technique (LST) is being investigated to characterize interface strength in fuel plates. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves to characterize interfaces in nuclear fuel plates. However the deposition of laser energy into the containment layer on specimen’s surface is intractably complex. The shock wave energy is inferred from the velocity on the backside and the depth of the impression left on the surface from the high pressure plasma pulse created by the shock laser. To help quantify the stresses and strengths at the interface, a finite element model is being developed and validated by comparing numerical and experimental results for back face velocities and front face depressions with experimental results. This paper will report on initial efforts to develop a finite element model for laser shock.« less

Computer-assisted quantification of the skull deformity for craniosynostosis from 3D head CT images using morphological descriptor and hierarchical classification

NASA Astrophysics Data System (ADS)

Lee, Min Jin; Hong, Helen; Shim, Kyu Won; Kim, Yong Oock

2017-03-01

This paper proposes morphological descriptors representing the degree of skull deformity for craniosynostosis in head CT images and a hierarchical classifier model distinguishing among normal and different types of craniosynostosis. First, to compare deformity surface model with mean normal surface model, mean normal surface models are generated for each age range and the mean normal surface model is deformed to the deformity surface model via multi-level threestage registration. Second, four shape features including local distance and area ratio indices are extracted in each five cranial bone. Finally, hierarchical SVM classifier is proposed to distinguish between the normal and deformity. As a result, the proposed method showed improved classification results compared to traditional cranial index. Our method can be used for the early diagnosis, surgical planning and postsurgical assessment of craniosynostosis as well as quantitative analysis of skull deformity.

Computation of Static Shapes and Voltages for Micromachined Deformable Mirrors with Nonlinear Electrostatic Actuators

NASA Technical Reports Server (NTRS)

Wang, P. K. C.; Hadaegh, F. Y.

1996-01-01

In modeling micromachined deformable mirrors with electrostatic actuators whose gap spacings are of the same order of magnitude as those of the surface deformations, it is necessary to use nonlinear models for the actuators. In this paper, we consider micromachined deformable mirrors modeled by a membrane or plate equation with nonlinear electrostatic actuator characteristics. Numerical methods for computing the mirror deformation due to given actuator voltages and the actuator voltages required for producing the desired deformations at the actuator locations are presented. The application of the proposed methods to circular deformable mirrors whose surfaces are modeled by elastic membranes is discussed in detail. Numerical results are obtained for a typical circular micromachined mirror with electrostatic actuators.

Evaluation of high-resolution sea ice models on the basis of statistical and scaling properties of Arctic sea ice drift and deformation

NASA Astrophysics Data System (ADS)

Girard, L.; Weiss, J.; Molines, J. M.; Barnier, B.; Bouillon, S.

2009-08-01

Sea ice drift and deformation from models are evaluated on the basis of statistical and scaling properties. These properties are derived from two observation data sets: the RADARSAT Geophysical Processor System (RGPS) and buoy trajectories from the International Arctic Buoy Program (IABP). Two simulations obtained with the Louvain-la-Neuve Ice Model (LIM) coupled to a high-resolution ocean model and a simulation obtained with the Los Alamos Sea Ice Model (CICE) were analyzed. Model ice drift compares well with observations in terms of large-scale velocity field and distributions of velocity fluctuations although a significant bias on the mean ice speed is noted. On the other hand, the statistical properties of ice deformation are not well simulated by the models: (1) The distributions of strain rates are incorrect: RGPS distributions of strain rates are power law tailed, i.e., exhibit "wild randomness," whereas models distributions remain in the Gaussian attraction basin, i.e., exhibit "mild randomness." (2) The models are unable to reproduce the spatial and temporal correlations of the deformation fields: In the observations, ice deformation follows spatial and temporal scaling laws that express the heterogeneity and the intermittency of deformation. These relations do not appear in simulated ice deformation. Mean deformation in models is almost scale independent. The statistical properties of ice deformation are a signature of the ice mechanical behavior. The present work therefore suggests that the mechanical framework currently used by models is inappropriate. A different modeling framework based on elastic interactions could improve the representation of the statistical and scaling properties of ice deformation.

Investigation on Insar Time Series Deformation Model Considering Rheological Parameters for Soft Clay Subgrade Monitoring

NASA Astrophysics Data System (ADS)

Xing, X.; Yuan, Z.; Chen, L. F.; Yu, X. Y.; Xiao, L.

2018-04-01

The stability control is one of the major technical difficulties in the field of highway subgrade construction engineering. Building deformation model is a crucial step for InSAR time series deformation monitoring. Most of the InSAR deformation models for deformation monitoring are pure empirical mathematical models, without considering the physical mechanism of the monitored object. In this study, we take rheology into consideration, inducing rheological parameters into traditional InSAR deformation models. To assess the feasibility and accuracy for our new model, both simulation and real deformation data over Lungui highway (a typical highway built on soft clay subgrade in Guangdong province, China) are investigated with TerraSAR-X satellite imagery. In order to solve the unknows of the non-linear rheological model, three algorithms: Gauss-Newton (GN), Levenberg-Marquarat (LM), and Genetic Algorithm (GA), are utilized and compared to estimate the unknown parameters. Considering both the calculation efficiency and accuracy, GA is chosen as the final choice for the new model in our case study. Preliminary real data experiment is conducted with use of 17 TerraSAR-X Stripmap images (with a 3-m resolution). With the new deformation model and GA aforementioned, the unknown rheological parameters over all the high coherence points are obtained and the LOS deformation (the low-pass component) sequences are generated.

Ground Measurements of Airplane Shock-Wave Noise at Mach Numbers to 2.0 and at Altitudes to 60,000 Feet

NASA Technical Reports Server (NTRS)

Lina, Lindsay J.; Maglieri, Domenic J.

1960-01-01

The intensity of shock-wave noise at the ground resulting from flights at Mach numbers to 2.0 and altitudes to 60,000 feet was measured. Meagurements near the ground track for flights of a supersonic fighter and one flight of a supersonic bomber are presented. Level cruising flight at an altitude of 60,000 feet and a Mach number of 2.0 produced sonic booms which were considered to be tolerable, and it is reasonable t o expect that cruising flight at higher altitudes will produce booms of tolerable intensity for airplanes of the size and weight of the test airplanes. The measured variation of sonic-boom intensity with altitude was in good agreement with the variation calculated by an equation given in NASA Technical Note D-48. The effect of Mach number on the ground overpressure is small between Mach numbers of 1.4 and 2.0, a result in agreement with the theory. No amplification of the shock-wave overpressures due to refraction effects was apparent near the cutoff Mach number. A method for estimating the effect of fligh-path angle on cutoff Mach number is shown. Experimental results indicate agreement with the method, since a climb maneuver produced booms of a much decreased intensity as compared with the intensity of those measured in level flight at about the same altitude and Mach number. Comparison of sound pressure levels for the fighter and bomber airp lanes indicated little effect of either airplane size or weight at an altitude of 40,000 feet.

Extracorporeal shockwave myocardial revascularization improves clinical symptoms and left ventricular function in patients with refractory angina.

PubMed

Zuozienė, Gitana; Laucevičius, Aleksandras; Leibowitz, David

2012-01-01

Medical therapy for refractory angina is limited and the prognosis is poor. Experimental data suggest that the use of extracorporeal shockwave myocardial revascularization (ESMR) can contribute to angiogenesis and improve symptoms of angina and left ventricular (LV) function. The objective of this study was to examine the effects of ESMR on clinical symptoms as well as LV function as assessed by cardiac MRI in patients with refractory angina. Patients with Canadian Cardiovascular Society (CCS) class III-IV angina despite medical therapy and ischemia documented on thallium or echo-dobutamine were eligible for the study. ESMR therapy was applied with a commercially available cardiac shockwave generator system under echocardiographic guidance. LV function was assessed before and 6 months after therapy by cardiac MRI. Twenty patients (four women, 16 men; mean age 64 years, range 45-83) were included in the study. The CCS class after treatment improved in all patients (16 patients angina pectoris CCS from III to II and four patients from IV to III). The use of sublingual nitroglycerin was significantly reduced as well. There was a significant improvement in LV ejection fraction as assessed by blinded MRI following therapy in the overall population (51 vs. 59%, P<0.05). This study demonstrates the potential efficacy of ESMR for the treatment of refractory angina pectoris. The patients showed both a significant clinical response as well as improved LV ejection fraction on serial MRI imaging. Larger studies are needed to adequately define the clinical utility of this novel therapy.

High Strain Rate Deformation Modeling of a Polymer Matrix Composite. Part 1; Matrix Constitutive Equations

NASA Technical Reports Server (NTRS)

Goldberg, Robert K.; Stouffer, Donald C.

1998-01-01

Recently applications have exposed polymer matrix composite materials to very high strain rate loading conditions, requiring an ability to understand and predict the material behavior under these extreme conditions. In this first paper of a two part report, background information is presented, along with the constitutive equations which will be used to model the rate dependent nonlinear deformation response of the polymer matrix. Strain rate dependent inelastic constitutive models which were originally developed to model the viscoplastic deformation of metals have been adapted to model the nonlinear viscoelastic deformation of polymers. The modified equations were correlated by analyzing the tensile/ compressive response of both 977-2 toughened epoxy matrix and PEEK thermoplastic matrix over a variety of strain rates. For the cases examined, the modified constitutive equations appear to do an adequate job of modeling the polymer deformation response. A second follow-up paper will describe the implementation of the polymer deformation model into a composite micromechanical model, to allow for the modeling of the nonlinear, rate dependent deformation response of polymer matrix composites.

An electromechanical based deformable model for soft tissue simulation.

PubMed

Zhong, Yongmin; Shirinzadeh, Bijan; Smith, Julian; Gu, Chengfan

2009-11-01

Soft tissue deformation is of great importance to surgery simulation. Although a significant amount of research efforts have been dedicated to simulating the behaviours of soft tissues, modelling of soft tissue deformation is still a challenging problem. This paper presents a new deformable model for simulation of soft tissue deformation from the electromechanical viewpoint of soft tissues. Soft tissue deformation is formulated as a reaction-diffusion process coupled with a mechanical load. The mechanical load applied to a soft tissue to cause a deformation is incorporated into the reaction-diffusion system, and consequently distributed among mass points of the soft tissue. Reaction-diffusion of mechanical load and non-rigid mechanics of motion are combined to govern the simulation dynamics of soft tissue deformation. An improved reaction-diffusion model is developed to describe the distribution of the mechanical load in soft tissues. A three-layer artificial cellular neural network is constructed to solve the reaction-diffusion model for real-time simulation of soft tissue deformation. A gradient based method is established to derive internal forces from the distribution of the mechanical load. Integration with a haptic device has also been achieved to simulate soft tissue deformation with haptic feedback. The proposed methodology does not only predict the typical behaviours of living tissues, but it also accepts both local and large-range deformations. It also accommodates isotropic, anisotropic and inhomogeneous deformations by simple modification of diffusion coefficients.

Combining the bi-Yang-Baxter deformation, the Wess-Zumino term and TsT transformations in one integrable σ-model

NASA Astrophysics Data System (ADS)

Delduc, F.; Hoare, B.; Kameyama, T.; Magro, M.

2017-10-01

A multi-parameter integrable deformation of the principal chiral model is presented. The Yang-Baxter and bi-Yang-Baxter σ-models, the principal chiral model plus a Wess-Zumino term and the TsT transformation of the principal chiral model are all recovered when the appropriate deformation parameters vanish. When the Lie group is SU(2), we show that this four-parameter integrable deformation of the SU(2) principal chiral model corresponds to the Lukyanov model.

Model Attitude and Deformation Measurements at the NASA Glenn Research Center

NASA Technical Reports Server (NTRS)

Woike, Mark R.

2008-01-01

The NASA Glenn Research Center is currently participating in an American Institute of Aeronautics and Astronautics (AIAA) sponsored Model Attitude and Deformation Working Group. This working group is chartered to develop a best practices document dealing with the measurement of two primary areas of wind tunnel measurements, 1) model attitude including alpha, beta and roll angle, and 2) model deformation. Model attitude is a principle variable in making aerodynamic and force measurements in a wind tunnel. Model deformation affects measured forces, moments and other measured aerodynamic parameters. The working group comprises of membership from industry, academia, and the Department of Defense (DoD). Each member of the working group gave a presentation on the methods and techniques that they are using to make model attitude and deformation measurements. This presentation covers the NASA Glenn Research Center s approach in making model attitude and deformation measurements.

Physics-based deformable organisms for medical image analysis

NASA Astrophysics Data System (ADS)

Hamarneh, Ghassan; McIntosh, Chris

2005-04-01

Previously, "Deformable organisms" were introduced as a novel paradigm for medical image analysis that uses artificial life modelling concepts. Deformable organisms were designed to complement the classical bottom-up deformable models methodologies (geometrical and physical layers), with top-down intelligent deformation control mechanisms (behavioral and cognitive layers). However, a true physical layer was absent and in order to complete medical image segmentation tasks, deformable organisms relied on pure geometry-based shape deformations guided by sensory data, prior structural knowledge, and expert-generated schedules of behaviors. In this paper we introduce the use of physics-based shape deformations within the deformable organisms framework yielding additional robustness by allowing intuitive real-time user guidance and interaction when necessary. We present the results of applying our physics-based deformable organisms, with an underlying dynamic spring-mass mesh model, to segmenting and labelling the corpus callosum in 2D midsagittal magnetic resonance images.

The outcome of extracorporeal shockwave lithotripsy for renal pelvic stone with and without JJ stent--a comparative study.

PubMed

Mohayuddin, Nazim; Malik, Hamad Afzal; Hussain, Manzoor; Tipu, Salman Ahmed; Shehzad, Asad; Hashmi, Altaf; Naqvi, Syed Ali Anwar; Rizvi, Syed Adibul Hasan

2009-03-01

To compare the outcome of Extra corporeal shockwave lithotripsy for a renal pelvic stone with and without JJ stent. A comparative cross sectional study was carried out at Sindh Institute of Urology and Transplantation from January 2007 to January 2008. Eighty patients with renal pelvic stone measuring 2cm +/- 2mm were selected for treatment with Extra Corporeal Shockwave Lithotripsy (ESWL). All of these patients were adults with normal renal function and had unilateral renal stones with negative urine cultures. Patients with renal failure and children were excluded. They were divided into two groups of 40 each. Group A patients underwent ESWL without a JJ stent and in Group B a JJ stent was placed before ESWL. SLX F2 electromagnetic ESWL machine was used to impart shock waves. 3000 shockwaves were given in a session. Both the groups were compared for renal colic, steinstrasse, fever, lower urinary tract symptoms (LUTS) emergency room visits and hospital admissions, stone clearance, number of ESWL sessions, auxilliary procedures, (percutaneous nephrostomy or ureterorenoscopy) and cost. Ureteric colic occurred in 13 (32.5%) patients in group A and in 3 (7.5%) patient in group B. Steinstrasse developed in 4 (10%) patients with out JJ stent and in 3 (7.5%) patients with JJ stent. Fever was encountered in 1 (2.5%) patient in group A and in 3 (7.5%) patient in group B. Mean emergency room visits were 2.1 per patient in group A and 0.7 per patient in group B. Stone clearance occurred in 33 (82.5%) patients in group A and 31 (77.5%) in group B. In group B lower urinary tract symptoms were found in 50% versus 20% in group A. Auxillary procedure was performed in one (2.5%) patient each in both groups. Pre ESWL JJ stenting for a 2 cm +/- 2 mm renal stone was not beneficial in terms of steinstrasse, fever, stone clearance and number of ESWL sessions. However ureteric colic was significantly less in the stented group. Lower urinary tract symptoms (LUTS) was also significantly high in the patients having a JJ stent. The cost of the treatment doubled in the stented group which is an important factor in our country. JJ stenting does not prove to be a cost effective procedure when compared to the reduction in complications.

Effect of laser generated shockwaves 1 on ex-vivo pigskin.

PubMed

Ramaprasad, Vidyunmala; Navarro, Artemio; Patel, Shahzad; Patel, Vikash; Nowroozi, Bryan N; Taylor, Zach D; Yong, William; Gupta, Vijay; Grundfest, Warren S

2014-10-01

Persistent bacterial infection prolongs hospitalizations, leading to increased healthcare costs. Treatment of these infections costs several billion dollars annually. Biofilm production is one mechanism by which bacteria become resistant. With the help of biofilms, bacteria withstand the host immune response and are much less susceptible to antibiotics. Currently, there is interest in the use of laser-generated shockwaves (LGS) to delaminate biofilm from infected wound surfaces; however, the safety of such an approach has not yet been established. Of particular concern are the thermal and mechanical effects of the shockwave treatment on the epidermis and the underlying collagen structure of the dermis. The present study is a preliminary investigation of the effect of LGS on freshly harvested ex vivo porcine skin tissue samples. Tissue samples for investigation were harvested immediately post-mortem and treated with LGS within 30 minutes. Previous studies have shown that laser fluences between 100 and 500 mJ/pulse are capable of delaminating biofilms off a variety of surfaces, thus our preliminary investigation focused on this range of laser energy. For each sample, LGS were produced via laser irradiation of a thin layer (0.5 µm) of titanium sandwiched between a 50 and 100 µm thick layer of water glass and a 0.1 mm thick sheet of Mylar. The rapid thermal expansion of the irradiated titanium film generates a transient compressive wave that is coupled through a liquid layer to the surface of the ex vivo pigskin sample. Shocked samples were immediately fixed in formalin and prepared for histological analysis. A blinded pathologist evaluated and scored each section on the basis of its overall appearance (O) and presence of linear/slit-like spaces roughly parallel to the surface of the skin (S). The scores were given on a scale of 0-3. The present investigation revealed no visible difference between the tissue sections of the control sample and those that were subjected to laser-generated shockwaves. There was no relationship between the scores received by the samples and the energy with which they were shocked. Preliminary investigation into the safety of the LGS treatment for biofilm delamination appears promising. Additional investigation will continue on ex vivo porcine samples, followed by an in vivo animal trial to better understand the physiological response to LGS treatment. © 2014 Wiley Periodicals, Inc.

HSR Model Deformation Measurements from Subsonic to Supersonic Speeds

NASA Technical Reports Server (NTRS)

Burner, A. W.; Erickson, G. E.; Goodman, W. L.; Fleming, G. A.

1999-01-01

This paper describes the video model deformation technique (VMD) used at five NASA facilities and the projection moire interferometry (PMI) technique used at two NASA facilities. Comparisons between the two techniques for model deformation measurements are provided. Facilities at NASA-Ames and NASA-Langley where deformation measurements have been made are presented. Examples of HSR model deformation measurements from the Langley Unitary Wind Tunnel, Langley 16-foot Transonic Wind Tunnel, and the Ames 12-foot Pressure Tunnel are presented. A study to improve and develop new targeting schemes at the National Transonic Facility is also described. The consideration of milled targets for future HSR models is recommended when deformation measurements are expected to be required. Finally, future development work for VMD and PMI is addressed.

Loading Deformation Characteristic Simulation Study of Engineering Vehicle Refurbished Tire

NASA Astrophysics Data System (ADS)

Qiang, Wang; Xiaojie, Qi; Zhao, Yang; Yunlong, Wang; Guotian, Wang; Degang, Lv

2018-05-01

The paper constructed engineering vehicle refurbished tire computer geometry model, mechanics model, contact model, finite element analysis model, did simulation study on load-deformation property of engineering vehicle refurbished tire by comparing with that of the new and the same type tire, got load-deformation of engineering vehicle refurbished tire under the working condition of static state and ground contact. The analysis result shows that change rules of radial-direction deformation and side-direction deformation of engineering vehicle refurbished tire are close to that of the new tire, radial-direction and side-direction deformation value is a little less than that of the new tire. When air inflation pressure was certain, radial-direction deformation linear rule of engineer vehicle refurbished tire would increase with load adding, however, side-direction deformation showed linear change rule, when air inflation pressure was low; and it would show increase of non-linear change rule, when air inflation pressure was very high.

Modeling of drop breakup in the bag breakup regime

NASA Astrophysics Data System (ADS)

Wang, C.; Chang, S.; Wu, H.; Xu, J.

2014-04-01

Several analytic models for predicting the drop deformation and breakup have been developed over the last three decades, but modeling drop breakup in the bag-type regime is less reported. In this Letter, a breakup model has been proposed to predict the drop deformation length and breakup time in the bag-type breakup regime in a more accurate manner. In the present model, the drop deformation which is approximately as the displacement of the centre of mass (c. m.) along the axis located at the centre of the drop, and the movement of c. m. is obtained by solving the pressure balance equation. The effects of the drop deformation on the drop external aerodynamic force are considered in this model. Drop breakup occurs when the deformation length reaches the maximum value and the maximum deformation length is a function of Weber number. The performance and applicability of the proposed breakup model are tested against the published experimental data.

Flows in forward deformable roll coating gaps: Comparison between spring and plane-strain models of roll cover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Carvalho, M.S.; Scriven, L.E.

1997-12-01

In this report the flow between rigid and a deformable rotating rolls fully submerged in a liquid pool is studied. The deformation of compliant roll cover is described by two different models (1) independent, radially oriented springs that deform in response to the traction force applied at the extremity of each or one-dimensional model, and (2) a plane-strain deformation of an incompressible Mooney-Rivlin material or non-linear elastic model. Based on the flow rate predictions of both models, an empirical relation between the spring constant of the one dimensional model and the roll cover thickness and elastic modulus is proposed.

Deformation-Aware Log-Linear Models

NASA Astrophysics Data System (ADS)

Gass, Tobias; Deselaers, Thomas; Ney, Hermann

In this paper, we present a novel deformation-aware discriminative model for handwritten digit recognition. Unlike previous approaches our model directly considers image deformations and allows discriminative training of all parameters, including those accounting for non-linear transformations of the image. This is achieved by extending a log-linear framework to incorporate a latent deformation variable. The resulting model has an order of magnitude less parameters than competing approaches to handling image deformations. We tune and evaluate our approach on the USPS task and show its generalization capabilities by applying the tuned model to the MNIST task. We gain interesting insights and achieve highly competitive results on both tasks.

A GPU based high-resolution multilevel biomechanical head and neck model for validating deformable image registration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neylon, J., E-mail: jneylon@mednet.ucla.edu; Qi, X.; Sheng, K.

Purpose: Validating the usage of deformable image registration (DIR) for daily patient positioning is critical for adaptive radiotherapy (RT) applications pertaining to head and neck (HN) radiotherapy. The authors present a methodology for generating biomechanically realistic ground-truth data for validating DIR algorithms for HN anatomy by (a) developing a high-resolution deformable biomechanical HN model from a planning CT, (b) simulating deformations for a range of interfraction posture changes and physiological regression, and (c) generating subsequent CT images representing the deformed anatomy. Methods: The biomechanical model was developed using HN kVCT datasets and the corresponding structure contours. The voxels inside amore » given 3D contour boundary were clustered using a graphics processing unit (GPU) based algorithm that accounted for inconsistencies and gaps in the boundary to form a volumetric structure. While the bony anatomy was modeled as rigid body, the muscle and soft tissue structures were modeled as mass–spring-damper models with elastic material properties that corresponded to the underlying contoured anatomies. Within a given muscle structure, the voxels were classified using a uniform grid and a normalized mass was assigned to each voxel based on its Hounsfield number. The soft tissue deformation for a given skeletal actuation was performed using an implicit Euler integration with each iteration split into two substeps: one for the muscle structures and the other for the remaining soft tissues. Posture changes were simulated by articulating the skeletal structure and enabling the soft structures to deform accordingly. Physiological changes representing tumor regression were simulated by reducing the target volume and enabling the surrounding soft structures to deform accordingly. Finally, the authors also discuss a new approach to generate kVCT images representing the deformed anatomy that accounts for gaps and antialiasing artifacts that may be caused by the biomechanical deformation process. Accuracy and stability of the model response were validated using ground-truth simulations representing soft tissue behavior under local and global deformations. Numerical accuracy of the HN deformations was analyzed by applying nonrigid skeletal transformations acquired from interfraction kVCT images to the model’s skeletal structures and comparing the subsequent soft tissue deformations of the model with the clinical anatomy. Results: The GPU based framework enabled the model deformation to be performed at 60 frames/s, facilitating simulations of posture changes and physiological regressions at interactive speeds. The soft tissue response was accurate with a R{sup 2} value of >0.98 when compared to ground-truth global and local force deformation analysis. The deformation of the HN anatomy by the model agreed with the clinically observed deformations with an average correlation coefficient of 0.956. For a clinically relevant range of posture and physiological changes, the model deformations stabilized with an uncertainty of less than 0.01 mm. Conclusions: Documenting dose delivery for HN radiotherapy is essential accounting for posture and physiological changes. The biomechanical model discussed in this paper was able to deform in real-time, allowing interactive simulations and visualization of such changes. The model would allow patient specific validations of the DIR method and has the potential to be a significant aid in adaptive radiotherapy techniques.« less

A machine learning approach for real-time modelling of tissue deformation in image-guided neurosurgery.

PubMed

Tonutti, Michele; Gras, Gauthier; Yang, Guang-Zhong

2017-07-01

Accurate reconstruction and visualisation of soft tissue deformation in real time is crucial in image-guided surgery, particularly in augmented reality (AR) applications. Current deformation models are characterised by a trade-off between accuracy and computational speed. We propose an approach to derive a patient-specific deformation model for brain pathologies by combining the results of pre-computed finite element method (FEM) simulations with machine learning algorithms. The models can be computed instantaneously and offer an accuracy comparable to FEM models. A brain tumour is used as the subject of the deformation model. Load-driven FEM simulations are performed on a tetrahedral brain mesh afflicted by a tumour. Forces of varying magnitudes, positions, and inclination angles are applied onto the brain's surface. Two machine learning algorithms-artificial neural networks (ANNs) and support vector regression (SVR)-are employed to derive a model that can predict the resulting deformation for each node in the tumour's mesh. The tumour deformation can be predicted in real time given relevant information about the geometry of the anatomy and the load, all of which can be measured instantly during a surgical operation. The models can predict the position of the nodes with errors below 0.3mm, beyond the general threshold of surgical accuracy and suitable for high fidelity AR systems. The SVR models perform better than the ANN's, with positional errors for SVR models reaching under 0.2mm. The results represent an improvement over existing deformation models for real time applications, providing smaller errors and high patient-specificity. The proposed approach addresses the current needs of image-guided surgical systems and has the potential to be employed to model the deformation of any type of soft tissue. Copyright © 2017 Elsevier B.V. All rights reserved.

Shock Wave Propagation in Layered Planetary Interiors: Revisited

NASA Astrophysics Data System (ADS)

Arkani-Hamed, J.; Monteux, J.

2017-12-01

The end of the terrestrial planet accretion is characterized by numerous large impacts. About 90% of the mass of a large planet is accreted while the core mantle separation is occurring, because of the accretionary and the short-lived radio-isotope heating. The characteristics of the shockwave propagation, hence the existing scaling laws are poorly known within the layered planets. Here, we use iSALE-2D hydrocode simulations to calculate shock pressure in a differentiated Mars type body for impact velocities of 5-20 km/s, and impactor sizes of 100-400 km. We use two different rheologies for the target interior, an inviscid model ("no-stress model") and a pressure and damage-dependent strength model ("elaborated model"). To better characterize the shock pressure within the whole mantle as a function of distance from the impact site, we propose the following distribution: (1) a near field zone larger than the isobaric core that extends to 7-15 times the projectile radius into the target, where the peak shock pressure decays exponentially with increasing distance, (2) a far field zone where the pressure decays with distance following a power law. The shock pressure decreases more rapidly with distance in the near field for the elaborated model than for the no-stress model because of the influence of acoustic fluidization and damage. However to better illustrate the influence of the rheology on the shock propagation, we use the same expressions to fit the shock pressure with distance for both models. At the core-mantle boundary, CMB, the peak shock pressure jumps as the shock wave enters the core. We derived the boundary condition at CMB for the peak shock pressure. It is less sensitive to the impact velocity or the impactor size, but strongly depends on the rheology of the planet's mantle. Because of the lower shock wave velocity in the core compared to that in the mantle, the refracted shockwave propagates toward the symmetry axis of the planet, and the shock pressure in the core decreases following a second power law. In this study, we express the output obtained from iSALE hydrocodes by scaling laws to illustrate the influence of the ray angle relative to the axis of symmetry, the target rheology, the impactor size and the impact velocity. We use these shock-pressure scaling laws to determine the impact heating of terrestrial planets.

Use of high-speed visualization for the study of shock-wave interactions with deformable porous materials

NASA Astrophysics Data System (ADS)

Skews, Beric W.; Glick, Gavin; Doyle, Graham K.; Lamond, Paul W.

1997-05-01

This paper describes the use of high-speed photography, and videography, in the study of material distortion and movement when a shock wave traverses a highly deformable porous structure, such as a blob of foam or a porous bed of particles. The effects of surface porosity can be significant in determining the nature of reflection of shock waves from surfaces. Not only are wave geometries substantially modified but the resulting wall pressures are also strongly affected. It, in addition, the surface is highly deformable by being made up of an elastic matrix or a collection of discrete particles, then the reflection geometry and loading can be even more complex. It is known, for example, that shock wave impact on open-cell polyurethane foam attached to a wall can cause a significant increase in pressure on the wall compared to reflection off a plane rigid wall without covering. The motion of the interface is an essential consideration in understanding the dynamics of these interactions. These studies could have application to the effects of blast wave propagation over complex surfaces such as forests, grasslands, and snow; as well as in establishing the efficacy of safety padding and attenuation materials under shock and impact loading conditions. Studies on an assortment of materials are presented, using a variety of visualization techniques. Recording methods used range from short duration flash photography (both shadow and schlieren), through multi-frame videography; to single frame, multi-exposure video capture with a camera capable of rates up to 1 million pictures per second. In the case of shock wave impact on specimens of polyurethane foam, the results clearly show the expulsion and reingestion of shock heated gas from within the foam body as the material collapses and then recovers, coupled with longitudinal and transverse oscillations of the body of the foam material. For blast wave propagation over porous beds, occurrence of particle lift off, bed fluidization, and the generation of surface dunes are evident. The recordings allow the calculation of the velocities and accelerations of the various interfaces and particles to be made, using suitable image processing techniques. Thus, estimates may be made of the unsteady drag forces acting on the individual particles.

Reducing Traffic Congestions by Introducing CACC-Vehicles on a Multi-Lane Highway Using Agent-Based Approach

NASA Technical Reports Server (NTRS)

Arnaout, Georges M.; Bowling, Shannon R.

2011-01-01

Traffic congestion is an ongoing problem of great interest to researchers from different areas in academia. With the emerging technology for inter-vehicle communication, vehicles have the ability to exchange information with predecessors by wireless communication. In this paper, we present an agent-based model of traffic congestion and examine the impact of having CACC (Cooperative Adaptive Cruise Control) embedded vehicle(s) on a highway system consisting of 4 traffic lanes without overtaking. In our model, CACC vehicles adapt their acceleration/deceleration according to vehicle-to-vehicle inter-communication. We analyze the average speed of the cars, the shockwaves, and the evolution of traffic congestion throughout the lifecycle of the model. The study identifies how CACC vehicles affect the dynamics of traffic flow on a complex network and reduce the oscillatory behavior (stop and go) resulting from the acceleration/deceleration of the vehicles.

Modeling dynamic beta-gamma polymorphic transition in Tin

NASA Astrophysics Data System (ADS)

Chauvin, Camille; Montheillet, Frank; Petit, Jacques; CEA Gramat Collaboration; EMSE Collaboration

2015-06-01

Solid-solid phase transitions in metals have been studied by shock waves techniques for many decades. Recent experiments have investigated the transition during isentropic compression experiments and shock-wave compression and have highlighted the strong influence of the loading rate on the transition. Complementary data obtained with velocity and temperature measurements around the polymorphic transition beta-gamma of Tin on gas gun experiments have displayed the importance of the kinetics of the transition. But, even though this phenomenon is known, modeling the kinetic remains complex and based on empirical formulations. A multiphase EOS is available in our 1D Lagrangian code Unidim. We propose to present the influence of various kinetic laws (either empirical or involving nucleation and growth mechanisms) and their parameters (Gibbs free energy, temperature, pressure) on the transformation rate. We compare experimental and calculated velocities and temperature profiles and we underline the effects of the empirical parameters of these models.

A Lattice Boltzmann Fictitious Domain Method for Modeling Red Blood Cell Deformation and Multiple-Cell Hydrodynamic Interactions in Flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Xing; Lin, Guang; Zou, Jianfeng

To model red blood cell (RBC) deformation in flow, the recently developed LBM-DLM/FD method ([Shi and Lim, 2007)29], derived from the lattice Boltzmann method and the distributed Lagrange multiplier/fictitious domain methodthe fictitious domain method, is extended to employ the mesoscopic network model for simulations of red blood cell deformation. The flow is simulated by the lattice Boltzmann method with an external force, while the network model is used for modeling red blood cell deformation and the fluid-RBC interaction is enforced by the Lagrange multiplier. To validate parameters of the RBC network model, sThe stretching numerical tests on both coarse andmore » fine meshes are performed and compared with the corresponding experimental data to validate the parameters of the RBC network model. In addition, RBC deformation in pipe flow and in shear flow is simulated, revealing the capacity of the current method for modeling RBC deformation in various flows.« less

Soft tissue deformation modelling through neural dynamics-based reaction-diffusion mechanics.

PubMed

Zhang, Jinao; Zhong, Yongmin; Gu, Chengfan

2018-05-30

Soft tissue deformation modelling forms the basis of development of surgical simulation, surgical planning and robotic-assisted minimally invasive surgery. This paper presents a new methodology for modelling of soft tissue deformation based on reaction-diffusion mechanics via neural dynamics. The potential energy stored in soft tissues due to a mechanical load to deform tissues away from their rest state is treated as the equivalent transmembrane potential energy, and it is distributed in the tissue masses in the manner of reaction-diffusion propagation of nonlinear electrical waves. The reaction-diffusion propagation of mechanical potential energy and nonrigid mechanics of motion are combined to model soft tissue deformation and its dynamics, both of which are further formulated as the dynamics of cellular neural networks to achieve real-time computational performance. The proposed methodology is implemented with a haptic device for interactive soft tissue deformation with force feedback. Experimental results demonstrate that the proposed methodology exhibits nonlinear force-displacement relationship for nonlinear soft tissue deformation. Homogeneous, anisotropic and heterogeneous soft tissue material properties can be modelled through the inherent physical properties of mass points. Graphical abstract Soft tissue deformation modelling with haptic feedback via neural dynamics-based reaction-diffusion mechanics.

ChainMail based neural dynamics modeling of soft tissue deformation for surgical simulation.

PubMed

Zhang, Jinao; Zhong, Yongmin; Smith, Julian; Gu, Chengfan

2017-07-20

Realistic and real-time modeling and simulation of soft tissue deformation is a fundamental research issue in the field of surgical simulation. In this paper, a novel cellular neural network approach is presented for modeling and simulation of soft tissue deformation by combining neural dynamics of cellular neural network with ChainMail mechanism. The proposed method formulates the problem of elastic deformation into cellular neural network activities to avoid the complex computation of elasticity. The local position adjustments of ChainMail are incorporated into the cellular neural network as the local connectivity of cells, through which the dynamic behaviors of soft tissue deformation are transformed into the neural dynamics of cellular neural network. Experiments demonstrate that the proposed neural network approach is capable of modeling the soft tissues' nonlinear deformation and typical mechanical behaviors. The proposed method not only improves ChainMail's linear deformation with the nonlinear characteristics of neural dynamics but also enables the cellular neural network to follow the principle of continuum mechanics to simulate soft tissue deformation.

Quantitative genetic properties of four measures of deformity in yellowtail kingfish Seriola lalandi Valenciennes, 1833.

PubMed

Nguyen, N H; Whatmore, P; Miller, A; Knibb, W

2016-02-01

The main aim of this study was to estimate the heritability for four measures of deformity and their genetic associations with growth (body weight and length), carcass (fillet weight and yield) and flesh-quality (fillet fat content) traits in yellowtail kingfish Seriola lalandi. The observed major deformities included lower jaw, nasal erosion, deformed operculum and skinny fish on 480 individuals from 22 families at Clean Seas Tuna Ltd. They were typically recorded as binary traits (presence or absence) and were analysed separately by both threshold generalized models and standard animal mixed models. Consistency of the models was evaluated by calculating simple Pearson correlation of breeding values of full-sib families for jaw deformity. Genetic and phenotypic correlations among traits were estimated using a multitrait linear mixed model in ASReml. Both threshold and linear mixed model analysis showed that there is additive genetic variation in the four measures of deformity, with the estimates of heritability obtained from the former (threshold) models on liability scale ranging from 0.14 to 0.66 (SE 0.32-0.56) and from the latter (linear animal and sire) models on original (observed) scale, 0.01-0.23 (SE 0.03-0.16). When the estimates on the underlying liability were transformed to the observed scale (0, 1), they were generally consistent between threshold and linear mixed models. Phenotypic correlations among deformity traits were weak (close to zero). The genetic correlations among deformity traits were not significantly different from zero. Body weight and fillet carcass showed significant positive genetic correlations with jaw deformity (0.75 and 0.95, respectively). Genetic correlation between body weight and operculum was negative (-0.51, P < 0.05). The genetic correlations' estimates of body and carcass traits with other deformity were not significant due to their relatively high standard errors. Our results showed that there are prospects for genetic selection to improve deformity in yellowtail kingfish and that measures of deformity should be included in the recording scheme, breeding objectives and selection index in practical selective breeding programmes due to the antagonistic genetic correlations of deformed jaws with body and carcass performance. © 2015 John Wiley & Sons Ltd.

A Cooperative V2V Alert System to Mitigate Vehicular Traffic ShockWaves

DOT National Transportation Integrated Search

2017-03-01

Vehicle traffic on highway systems are typically not uniformly distributed. In our work, we introduce a protocol that exploits this phenomenon by considering the formations of shock waves and opportunities in adjacent lanes. The objective of this pro...

An experimental and numerical investigation of shock-wave induced turbulent boundary-layer separation at hypersonic speeds

NASA Technical Reports Server (NTRS)

Marvin, J. G.; Horstman, C. C.; Rubesin, M. W.; Coakley, T. J.; Kussoy, M. I.

1975-01-01

An experiment designed to test and guide computations of the interaction of an impinging shock wave with a turbulent boundary layer is described. Detailed mean flow-field and surface data are presented for two shock strengths which resulted in attached and separated flows, respectively. Numerical computations, employing the complete time-averaged Navier-Stokes equations along with algebraic eddy-viscosity and turbulent Prandtl number models to describe shear stress and heat flux, are used to illustrate the dependence of the computations on the particulars of the turbulence models. Models appropriate for zero-pressure-gradient flows predicted the overall features of the flow fields, but were deficient in predicting many of the details of the interaction regions. Improvements to the turbulence model parameters were sought through a combination of detailed data analysis and computer simulations which tested the sensitivity of the solutions to model parameter changes. Computer simulations using these improvements are presented and discussed.

Testing deformation hypotheses by constraints on a time series of geodetic observations

NASA Astrophysics Data System (ADS)

Velsink, Hiddo

2018-01-01

In geodetic deformation analysis observations are used to identify form and size changes of a geodetic network, representing objects on the earth's surface. The network points are monitored, often continuously, because of suspected deformations. A deformation may affect many points during many epochs. The problem is that the best description of the deformation is, in general, unknown. To find it, different hypothesised deformation models have to be tested systematically for agreement with the observations. The tests have to be capable of stating with a certain probability the size of detectable deformations, and to be datum invariant. A statistical criterion is needed to find the best deformation model. Existing methods do not fulfil these requirements. Here we propose a method that formulates the different hypotheses as sets of constraints on the parameters of a least-squares adjustment model. The constraints can relate to subsets of epochs and to subsets of points, thus combining time series analysis and congruence model analysis. The constraints are formulated as nonstochastic observations in an adjustment model of observation equations. This gives an easy way to test the constraints and to get a quality description. The proposed method aims at providing a good discriminating method to find the best description of a deformation. The method is expected to improve the quality of geodetic deformation analysis. We demonstrate the method with an elaborate example.

Niobium superconducting rf cavity fabrication by electrohydraulic forming

NASA Astrophysics Data System (ADS)

Cantergiani, E.; Atieh, S.; Léaux, F.; Perez Fontenla, A. T.; Prunet, S.; Dufay-Chanat, L.; Koettig, T.; Bertinelli, F.; Capatina, O.; Favre, G.; Gerigk, F.; Jeanson, A. C.; Fuzeau, J.; Avrillaud, G.; Alleman, D.; Bonafe, J.; Marty, P.

2016-11-01

Superconducting rf (SRF) cavities are traditionally fabricated from superconducting material sheets or made of copper coated with superconducting material, followed by trim machining and electron-beam welding. An alternative technique to traditional shaping methods, such as deep-drawing and spinning, is electrohydraulic forming (EHF). In EHF, half-cells are obtained through ultrahigh-speed deformation of blank sheets, using shockwaves induced in water by a pulsed electrical discharge. With respect to traditional methods, such a highly dynamic process can yield interesting results in terms of effectiveness, repeatability, final shape precision, higher formability, and reduced springback. In this paper, the first results of EHF on high purity niobium are presented and discussed. The simulations performed in order to master the multiphysics phenomena of EHF and to adjust its process parameters are presented. The microstructures of niobium half-cells produced by EHF and by spinning have been compared in terms of damage created in the material during the forming operation. The damage was assessed through hardness measurements, residual resistivity ratio (RRR) measurements, and electron backscattered diffraction analyses. It was found that EHF does not worsen the damage of the material during forming and instead, some areas of the half-cell have shown lower damage compared to spinning. Moreover, EHF is particularly advantageous to reduce the forming time, preserve roughness, and to meet the final required shape accuracy.

[Extracorporeal shock-wave lithotripsy of gallstones].

PubMed

Freund, H R; Lebensart, P D; Muggia-Sullam, M; Durst, A L

1989-08-01

We performed 16 extracorporeal shock-wave lithotripsies (ESWL) to fragment gallstones in 11 women and 2 men, aged 19 to 57 (mean 41 +/- 10) years, during the past 10 months. Criteria for selection included a history of biliary colic, not more than 3 stones with a total diameter of not more than 30 mm, and a functioning gallbladder. 210 patients were examined, of whom 98 were referred for additional screening by combined ultrasonography and oral cholecystography. This resulted in rejection of another 71 patients due to multiple stones (38%), nonfunctioning gallbladder (22%), calcified stones (12%), stones not visualized in the prone position (9%), excessively large stones (3%) and other reasons (16%). Only 27 patients fulfilled all the criteria. Under epidural or general anesthesia (11 and 2 patients, respectively), we administered 1200-3500 (mean 2250 +/- 750) shock waves at 20-24 KV with the Tripter X1 (Direx, Israel-USA). This is an ultrasound-guided, modular portable, shock-wave generator utilizing underwater high energy spark discharge. Chenodeoxycholic or ursodeoxycholic acid, 10 mg/kg/day, was started 1 week prior to ESWL and continued for 3 months after disappearance of fragments and debris. We encountered skin petechiae in all patients, transient hematuria in 8, mild biliary colic in 1 and a small liver hematoma in 1. To date, 3 patients are free of stones, while in 7 only sludge and tiny fragments are present which we expect to disappear as a result of the litholytic therapy. 3 patients had fragments larger than 5 mm and required a second ESWL. Thus ESWL, which was indicated in only 13% of screened patients, proved to be safe and can be expected to be successful in 75% of selected candidates.

[The long-term results of the application of the combined rehabilitative treatment in the patients presenting with knee osteoarthrosis].

PubMed

Razumov, A N; Purigа, A O; Yurova, O V

2015-01-01

The rehabilitative treatment of the patients suffering from knee osteoarthrosis (OA) up-to-date remains one of the most important medical and social problems of modern medicine due to the high prevalence of this disease, heavy morbidity, and the significant deterioration of the quality of the patients' life. The objective of the present study was to evaluate the long-term results of the combined application of radon and extracorporeal shock-wave therapy for the rehabilitation of the patients presenting with knee OA. The study involved 75 patients at the age from 35 to 62 years with the confirmed diagnosis of stage II and III knee osteoarthrosis. They were divided into 3 groups. Those comprising the main group received extracorporeal shock-wave therapy in combination with the treatment based on the use of radon baths. The patients included in the group of comparison were given a course of radon therapy alone while the patients of the control group received the standard treatment including physiotherapy, magnetic therapy, and the use of non-steroidal anti-inflammatory drugs (NSAIDs). The study has demonstrated the high effectiveness of the combined application of the radon baths and extracorporeal shock-wave therapy that was manifested as the substantial decrease of pain intensity, the increased range of motion in the knee joints, and the improvement of the general quality of life. These beneficial effects persisted during a period of up to 12 months. The stable remission was documented in 82% of the patients comprising the main group. The data obtained give reason to recommend the method employed in the present study for the extensive practical application at different stages of medical rehabilitation of the patients presenting with knee osteoarthrosis.

Targeted microbubbles: a novel application for the treatment of kidney stones.

PubMed

Ramaswamy, Krishna; Marx, Vanessa; Laser, Daniel; Kenny, Thomas; Chi, Thomas; Bailey, Michael; Sorensen, Mathew D; Grubbs, Robert H; Stoller, Marshall L

2015-07-01

Kidney stone disease is endemic. Extracorporeal shockwave lithotripsy was the first major technological breakthrough where focused shockwaves were used to fragment stones in the kidney or ureter. The shockwaves induced the formation of cavitation bubbles, whose collapse released energy at the stone, and the energy fragmented the kidney stones into pieces small enough to be passed spontaneously. Can the concept of microbubbles be used without the bulky machine? The logical progression was to manufacture these powerful microbubbles ex vivo and inject these bubbles directly into the collecting system. An external source can be used to induce cavitation once the microbubbles are at their target; the key is targeting these microbubbles to specifically bind to kidney stones. Two important observations have been established: (i) bisphosphonates attach to hydroxyapatite crystals with high affinity; and (ii) there is substantial hydroxyapatite in most kidney stones. The microbubbles can be equipped with bisphosphonate tags to specifically target kidney stones. These bubbles will preferentially bind to the stone and not surrounding tissue, reducing collateral damage. Ultrasound or another suitable form of energy is then applied causing the microbubbles to induce cavitation and fragment the stones. This can be used as an adjunct to ureteroscopy or percutaneous lithotripsy to aid in fragmentation. Randall's plaques, which also contain hydroxyapatite crystals, can also be targeted to pre-emptively destroy these stone precursors. Additionally, targeted microbubbles can aid in kidney stone diagnostics by virtue of being used as an adjunct to traditional imaging methods, especially useful in high-risk patient populations. This novel application of targeted microbubble technology not only represents the next frontier in minimally invasive stone surgery, but a platform technology for other areas of medicine. © 2014 The Authors BJU International © 2014 BJU International Published by John Wiley & Sons Ltd.

Treatment of Chronic Plantar Fasciitis with Noninvasive Interactive Neurostimulation: A Prospective Randomized Controlled Study.

PubMed

Razzano, Cristina; Carbone, Stefano; Mangone, Massimiliano; Iannotta, M Raffaella; Battaglia, Alessandro; Santilli, Valter

The initial treatment of plantar fasciitis should be conservative, with most cases responding to standard physiotherapy, nonsteroidal anti-inflammatory drugs (NSAIDs), heel pads, and stretching. In cases of chronic refractory symptoms, more invasive treatment could be necessary. Noninvasive interactive neurostimulation (NIN) is a form of electric therapy that works by locating areas of lower skin impedance. The objective of the present prospective randomized controlled study was to evaluate whether the use of NIN for chronic plantar fasciitis could result in greater improvement in a foot functional score, lower levels of reported pain, reduced patient consumption of NSAIDs, and greater patient satisfaction compared with electric shockwave therapy in patients without a response to standard conservative treatment. The patients were randomized using random blocks to the NIN program (group 1) or electric shockwave therapy (group 2). The outcome measurements were the pain subscale of the validated Foot Function Index (PS-FFI), patient-reported subjective assessment of the level of pain using a standard visual analog scale, and daily intake of NSAID tablets (etoricoxib 60 mg). The study group was evaluated at baseline (time 0), week 4 (time 1), and week 12 (final follow-up point). Group 1 (55 patients) experienced significantly better results compared with group 2 (49 patients) in term of the PS-FFI score, visual analog scale score, and daily intake of etoricoxib 60 mg. NIN was an effective treatment of chronic resistant plantar fasciitis, with full patient satisfaction in >90% of cases. The present prospective randomized controlled study showed superior results for noninvasive neurostimulation compared with electric shockwave therapy, in terms of the functional score, pain improvement, and use of NSAIDs. Copyright © 2017 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

[Color processing of ultrasonographic images in extracorporeal lithotripsy].

PubMed

Lardennois, B; Ziade, A; Walter, K

1991-02-01

A number of technical difficulties are encountered in the ultrasonographic detection of renal stones which unfortunately limit its performance. The margin of error of firing in extracorporeal shock-wave lithotripsy (ESWL) must be reduced to a minimum. The role of the ultrasonographic monitoring during lithotripsy is also essential: continuous control of the focussing of the short-wave beamand assessment if the quality of fragmentation. The authors propose to improve ultrasonographic imaging in ESWL by means of intraoperative colour processing of the stone. Each shot must be directed to its target with an economy of vision avoiding excessive fatigue. The principle of the technique consists of digitalization of the ultrasound video images using a Macintosh Mac 2 computer. The Graphis Paint II program is interfaced directly with the Quick Capture card and recovers the images on its work surface in real time. The program is then able to attribute to each of these 256 shades of grey any one of the 16.6 million colours of the Macintosh universe with specific intensity and saturation. During fragmentation, using the principle of a palette, the stone changes colour from green to red indicating complete fragmentation. A Color Space card converts the digital image obtained into a video analogue source which is visualized on the monitor. It can be superimposed and/or juxtaposed with the source image by means of a multi-standard mixing table. Colour processing of ultrasonographic images in extracoporeal shockwave lithotripsy allows better visualization of the stones and better follow-up of fragmentation and allows the shockwave treatment to be stopped earlier. It increases the stone-free performance at 6 months. This configuration will eventually be able to integrate into the ultrasound apparatus itself.

Low-Intensity Extracorporeal Shockwave Therapy Can Improve Erectile Function in Patients Who Failed to Respond to Phosphodiesterase Type 5 Inhibitors

PubMed Central

Tsai, Chia-Chun; Wang, Chii-Jye; Lee, Yung-Chin; Kuo, Yen-Ting; Lin, Hsiao-Hua; Li, Ching-Chia; Wu, Wen-Jeng; Liu, Chia-Chu

2017-01-01

Managing patients with erectile dysfunction (ED) who failed to respond to phosphodiesterase type 5 inhibitors (PDE5is) is a challenging task. Recently, low-intensity extracorporeal shockwave therapy (LI-ESWT) was reported to improve ED by enhancing perfusion of the penis. The current study was performed to evaluate whether combined treatment with LI-ESWT and PDE5is can restore erectile function in patients who failed to respond to PDE5is alone. This was an open-label single-arm prospective study. ED patients with an erection hardness score (EHS) ≦2 under a maximal dosage of PDE5is were enrolled. Sociodemographic information and detailed medical history were recorded. LI-ESWT treatment consisted of 3,000 shockwaves once weekly for 12 weeks. All patients continued their regular PDE5is use. The EHS and the 5-item version of the International Index of Erectile Function (IIEF-5) were used to evaluate the change in erectile function 1 and 3 months after LI-ESWT. A total of 52 patients were enrolled. After LI-ESWT treatment, 35 of the 52 patients (67.3%) could achieve an erection hard enough for intercourse (EHS ≧ 3) under PDE5is use at the 1-month follow-up. Initial severity of ED was the only significant predictor of a successful response (EHS1: 35.7% vs. EHS2: 78.9%, p = .005). Thirty-three of the 35 (94.3%) subjects who responded to LI-ESWT could still maintain their erectile function at the 3-month follow-up. LI-ESWT can serve as a salvage therapy for ED patients who failed to respond to PDE5is. Initial severity of ED was an important predictor of a successful response. PMID:28884638

Safety and efficacy of low intensity shockwave (LISW) treatment in patients with erectile dysfunction

PubMed Central

Ruffo, A.; Capece, M.; Prezioso, D.; Romeo, G.; Illiano, E.; Romis, L.; Lauro, G. Di; Iacono, F.

2015-01-01

ABSTRACT The primary goal in the management strategy of a patient with ED would be to determine its etiology and cure it when possible, and not just to treat the symptoms alone. One of the new therapeutic strategies is the use of low intensity extracorporeal shockwave (LISW) therapy. The mechanism of shockwave therapy is not completely clear. It is suggested that LISW induces neovascularization and improvement of cavernosal arterial flow which can lead to an improvement of erectile function by releasing NO, VEGF and PCNA. Materials and Methods: 31 patients between February and June 2013 with mild to severe ED and non-Phosphodiesterase 5 inhibitors responders were enrolled. Patients underwent four weekly treatment sessions. During each session 3600 shocks at 0.09mJ/ mm2 were given, 900 shocks at each anatomical area (right and left corpus cavernosum, right and left crus). Improvement of the erectile function was evaluated using the International Index of Erectile Function (IIEF-EF), the Sexual Encounter Profile (SEP) diaries (SEP-Questions 2 and 3) and Global Assessment Questions (GAQ-Q1 and GAQ-Q2). Results: At 3-month follow-up IIEF-EF scores improved from 16.54±6.35 at baseline to 21.03±6.38. Patients answering ‘yes’ to the SEP-Q2 elevated from 61% to 89% and from 32% to 62% in the SEP-Q3. A statistically significant improvement was reported to the Global Assessment Questions (GAQ-Q1 and GAQ-Q2). Conclusion: In conclusion, we can affirm that LISW is a confirmed therapeutic approach to erectile dysfunction that definitely needs more long-term trials to be clarified and further verified. PMID:26689523

Multiphase Equations of State for Polymer Materials at High Dynamic Pressures

NASA Astrophysics Data System (ADS)

Khishchenko, Konstantin V.

2015-06-01

Equations of state for materials over a wide range of pressures and temperatures are necessary for numerical simulations of shock-wave processes in condensed matter. Accuracy of calculation results is determined mainly by adequacy of equation of state of a medium. In this work, a new multiphase equation-of-state model is proposed with taking into account the polymorphic phase transformations, melting and evaporation. Thermodynamic calculations are carried out for 2 polymer materials (polymethylmethacrylate and polytetrafluoroethylene) in a broad region of the phase diagram. Obtained results are presented in comparison with available data of experiments at high dynamic pressures in shock and release waves. This work is supported by RSF, Grant 14-50-00124.

A Deformable Generic 3D Model of Haptoral Anchor of Monogenean

PubMed Central

Teo, Bee Guan; Dhillon, Sarinder Kaur; Lim, Lee Hong Susan

2013-01-01

In this paper, a digital 3D model which allows for visualisation in three dimensions and interactive manipulation is explored as a tool to help us understand the structural morphology and elucidate the functions of morphological structures of fragile microorganisms which defy live studies. We developed a deformable generic 3D model of haptoral anchor of dactylogyridean monogeneans that can subsequently be deformed into different desired anchor shapes by using direct manipulation deformation technique. We used point primitives to construct the rectangular building blocks to develop our deformable 3D model. Point primitives are manually marked on a 2D illustration of an anchor on a Cartesian graph paper and a set of Cartesian coordinates for each point primitive is manually extracted from the graph paper. A Python script is then written in Blender to construct 3D rectangular building blocks based on the Cartesian coordinates. The rectangular building blocks are stacked on top or by the side of each other following their respective Cartesian coordinates of point primitive. More point primitives are added at the sites in the 3D model where more structural variations are likely to occur, in order to generate complex anchor structures. We used Catmull-Clark subdivision surface modifier to smoothen the surface and edge of the generic 3D model to obtain a smoother and more natural 3D shape and antialiasing option to reduce the jagged edges of the 3D model. This deformable generic 3D model can be deformed into different desired 3D anchor shapes through direct manipulation deformation technique by aligning the vertices (pilot points) of the newly developed deformable generic 3D model onto the 2D illustrations of the desired shapes and moving the vertices until the desire 3D shapes are formed. In this generic 3D model all the vertices present are deployed for displacement during deformation. PMID:24204903

A deformable generic 3D model of haptoral anchor of Monogenean.

PubMed

Teo, Bee Guan; Dhillon, Sarinder Kaur; Lim, Lee Hong Susan

2013-01-01

In this paper, a digital 3D model which allows for visualisation in three dimensions and interactive manipulation is explored as a tool to help us understand the structural morphology and elucidate the functions of morphological structures of fragile microorganisms which defy live studies. We developed a deformable generic 3D model of haptoral anchor of dactylogyridean monogeneans that can subsequently be deformed into different desired anchor shapes by using direct manipulation deformation technique. We used point primitives to construct the rectangular building blocks to develop our deformable 3D model. Point primitives are manually marked on a 2D illustration of an anchor on a Cartesian graph paper and a set of Cartesian coordinates for each point primitive is manually extracted from the graph paper. A Python script is then written in Blender to construct 3D rectangular building blocks based on the Cartesian coordinates. The rectangular building blocks are stacked on top or by the side of each other following their respective Cartesian coordinates of point primitive. More point primitives are added at the sites in the 3D model where more structural variations are likely to occur, in order to generate complex anchor structures. We used Catmull-Clark subdivision surface modifier to smoothen the surface and edge of the generic 3D model to obtain a smoother and more natural 3D shape and antialiasing option to reduce the jagged edges of the 3D model. This deformable generic 3D model can be deformed into different desired 3D anchor shapes through direct manipulation deformation technique by aligning the vertices (pilot points) of the newly developed deformable generic 3D model onto the 2D illustrations of the desired shapes and moving the vertices until the desire 3D shapes are formed. In this generic 3D model all the vertices present are deployed for displacement during deformation.

Initiation of deformation of the Eastern California Shear Zone: Constraints from Garlock fault geometry and GPS observations

USGS Publications Warehouse

Gan, Weijun; Zhang, P.; Shen, Z.-K.; Prescott, W.H.; Svarc, J.L.

2003-01-01

We suggest a 2-stage deformation model for the Eastern California Shear Zone (ECSZ) to explain the geometry of the Garlock fault trace. We assume the Garlock fault was originally straight and then was gradually curved by right-lateral shear deformation across the ECSZ. In our 2-stage deformation model, the first stage involves uniform shear deformation across the eastern part of the shear zone, and the second stage involves uniform shear deformation across the entire shear zone. In addition to the current shape of the Garlock fault, our model incorporates constraints on contemporary deformation rates provided by GPS observations. We find that the best fitting age for initiation of shear in eastern part of the ECSZ is about 5.0 ?? 0.4 Ma, and that deformation of the western part started about 1.6 Myr later.

Meshless Modeling of Deformable Shapes and their Motion

PubMed Central

Adams, Bart; Ovsjanikov, Maks; Wand, Michael; Seidel, Hans-Peter; Guibas, Leonidas J.

2010-01-01

We present a new framework for interactive shape deformation modeling and key frame interpolation based on a meshless finite element formulation. Starting from a coarse nodal sampling of an object’s volume, we formulate rigidity and volume preservation constraints that are enforced to yield realistic shape deformations at interactive frame rates. Additionally, by specifying key frame poses of the deforming shape and optimizing the nodal displacements while targeting smooth interpolated motion, our algorithm extends to a motion planning framework for deformable objects. This allows reconstructing smooth and plausible deformable shape trajectories in the presence of possibly moving obstacles. The presented results illustrate that our framework can handle complex shapes at interactive rates and hence is a valuable tool for animators to realistically and efficiently model and interpolate deforming 3D shapes. PMID:24839614

Combination of low-energy shock-wave therapy and bone marrow mesenchymal stem cell transplantation to improve the erectile function of diabetic rats

PubMed Central

Shan, Hai-Tao; Zhang, Hai-Bo; Chen, Wen-Tao; Chen, Feng-Zhi; Wang, Tao; Luo, Jin-Tai; Yue, Min; Lin, Ji-Hong; Wei, An-Yang

2017-01-01

Stem cell transplantation and low-energy shock-wave therapy (LESWT) have emerged as potential and effective treatment protocols for diabetic erectile dysfunction. During the tracking of transplanted stem cells in diabetic erectile dysfunction models, the number of visible stem cells was rather low and decreased quickly. LESWT could recruit endogenous stem cells to the cavernous body and improve the microenvironment in diabetic cavernous tissue. Thus, we deduced that LESWT might benefit transplanted stem cell survival and improve the effects of stem cell transplantation. In this research, 42 streptozotocin-induced diabetic rats were randomized into four groups: the diabetic group (n = 6), the LESWT group (n = 6), the bone marrow-derived mesenchymal stem cell (BMSC) transplantation group (n = 15), and the combination of LESWT and BMSC transplantation group (n = 15). One and three days after BMSC transplantation, three rats were randomly chosen to observe the survival numbers of BMSCs in the cavernous body. Four weeks after BMSC transplantation, the following parameters were assessed: the surviving number of transplanted BMSCs in the cavernous tissue, erectile function, real-time polymerase chain reaction, and penile immunohistochemical assessment. Our research found that LESWT favored the survival of transplanted BMSCs in the cavernous body, which might be related to increased stromal cell-derived factor-1 expression and the enhancement of angiogenesis in the diabetic cavernous tissue. The combination of LESWT and BMSC transplantation could improve the erectile function of diabetic erectile function rats more effectively than LESWT or BMSC transplantation performed alone. PMID:27427555

Combination of low-energy shock-wave therapy and bone marrow mesenchymal stem cell transplantation to improve the erectile function of diabetic rats.

PubMed

Shan, Hai-Tao; Zhang, Hai-Bo; Chen, Wen-Tao; Chen, Feng-Zhi; Wang, Tao; Luo, Jin-Tai; Yue, Min; Lin, Ji-Hong; Wei, An-Yang

2017-01-01

Stem cell transplantation and low-energy shock-wave therapy (LESWT) have emerged as potential and effective treatment protocols for diabetic erectile dysfunction. During the tracking of transplanted stem cells in diabetic erectile dysfunction models, the number of visible stem cells was rather low and decreased quickly. LESWT could recruit endogenous stem cells to the cavernous body and improve the microenvironment in diabetic cavernous tissue. Thus, we deduced that LESWT might benefit transplanted stem cell survival and improve the effects of stem cell transplantation. In this research, 42 streptozotocin-induced diabetic rats were randomized into four groups: the diabetic group (n = 6), the LESWT group (n = 6), the bone marrow-derived mesenchymal stem cell (BMSC) transplantation group (n = 15), and the combination of LESWT and BMSC transplantation group (n = 15). One and three days after BMSC transplantation, three rats were randomly chosen to observe the survival numbers of BMSCs in the cavernous body. Four weeks after BMSC transplantation, the following parameters were assessed: the surviving number of transplanted BMSCs in the cavernous tissue, erectile function, real-time polymerase chain reaction, and penile immunohistochemical assessment. Our research found that LESWT favored the survival of transplanted BMSCs in the cavernous body, which might be related to increased stromal cell-derived factor-1 expression and the enhancement of angiogenesis in the diabetic cavernous tissue. The combination of LESWT and BMSC transplantation could improve the erectile function of diabetic erectile function rats more effectively than LESWT or BMSC transplantation performed alone.

Effect of focused and radial extracorporeal shock wave therapy on equine bone microdamage.

PubMed

Da Costa Gómez, Támara M; Radtke, Catherine L; Kalscheur, Vicki L; Swain, Carol A; Scollay, Mary C; Edwards, Ryland B; Santschi, Elizabeth M; Markel, Mark D; Muir, Peter

2004-01-01

To determine whether bone microcracks are altered after application of focused and radial extracorporeal shock wave therapy (ESWT) to the equine distal limb. An ex vivo experimental model. A contralateral limb specimen was obtained from 11 Thoroughbred racehorses with a unilateral catastrophic injury. Distal limb specimens were also obtained from 5 non-racing horses. Three separate skin-covered bone segments were obtained from the mid-diaphysis of the metacarpus (MC3) or metatarsus (MT3). Focused (9,000 shockwaves, 0.15 mJ/mm2, 4 Hz) and radial (9,000 shockwaves, 0.175 mJ/mm2, 4 Hz) ESWT treatments were randomized to the proximal and distal segments and the middle segment was used as a treatment control for pre-existing microcracks. After treatment, bone specimens were bulk-stained with basic fuchsin and microcracks were quantified in transverse calcified bone sections. ESWT had small but significant effects on microcracks. Microcrack density (Cr.Dn) and microcrack surface density (Cr.S.Dn) were increased after focused ESWT, whereas Cr.Le was increased after radial ESWT. In racing Thoroughbreds, Cr.Le increased with increased number of races undertaken. Cr.Dn and Cr.S.Dn were not significantly influenced by the number of races undertaken. ESWT has small but significant effects on bone microcracking ex vivo. These preliminary data suggest that ESWT has the potential to increase bone microcracking in equine distal limb bone in vivo. Such effects may be more pronounced in Thoroughbreds that are actively being raced, because in vivo microcracking increases with increased number of races undertaken.

COLLABORATIVE HYDROLOGIC RESEARCH IN THE CLARKSBURG SPECIAL PROTECTION AREA

EPA Science Inventory

This research project is focused on the Clarksburg Special Protection Area (CSPA) in Montgomery County, Maryland. The CSPA subwatersheds are on the outer edge of the urban development shockwave expanding outward from the Washington DC metropolitan area. This is an area of rapid d...

Flow-around modes for a rhomboid wing with a stall vortex in the shock layer

NASA Astrophysics Data System (ADS)

Zubin, M. A.; Maximov, F. A.; Ostapenko, N. A.

2017-12-01

The results of theoretical and experimental investigation of an asymmetrical hypersonic flow around a V-shaped wing with the opening angle larger than π on the modes with attached shockwaves on forward edges, when the stall flow is implemented on the leeward wing cantilever behind the kink point of the cross contour. In this case, a vortex of nonviscous nature is formed in which the velocities on the sphere exceeding the speed of sound and resulting in the occurrence of pressure shocks with an intensity sufficient for the separation of the turbulent boundary layer take place in the reverse flow according to the calculations within the framework of the ideal gas. It is experimentally established that a separation boundary layer can exist in the reverse flow, and its structure is subject to the laws inherent to the reverse flow in the separation region of the turbulent boundary layer arising in the supersonic conic flow under the action of a shockwave incident to the boundary layer.

Effect of target-fixture geometry on shock-wave compacted copper powders

NASA Astrophysics Data System (ADS)

Kim, Wooyeol; Ahn, Dong-Hyun; Yoon, Jae Ik; Park, Lee Ju; Kim, Hyoung Seop

2018-01-01

In shock compaction with a single gas gun system, a target fixture is used to safely recover a powder compact processed by shock-wave dynamic impact. However, no standard fixture geometry exists, and its effect on the processed compact is not well studied. In this study, two types of fixture are used for the dynamic compaction of hydrogen-reduced copper powders, and the mechanical properties and microstructures are investigated using the Vickers microhardness test and electron backscatter diffraction, respectively. With the assistance of finite element method simulations, we analyze several shock parameters that are experimentally hard to control. The results of the simulations indicate that the target geometry clearly affects the characteristics of incident and reflected shock waves. The hardness distribution and the microstructure of the compacts also show their dependence on the geometry. With the results of the simulations and the experiment, it is concluded that the target geometry affects the shock wave propagation and wave interaction in the specimen.

Extracorporeal shockwave therapy in a dog with chronic bicipital tenosynovitis.

PubMed

Venzin, C; Ohlerth, S; Koch, D; Spreng, D

2004-03-01

A 15-month-old, spayed female, Bernese mountain dog was presented to the Institute of Small Animal Surgery at the University of Zurich because of chronic left forelimb lameness. The referring veterinarian diagnosed pain in the left shoulder region and had treated the dog with systemic non-steroidal anti-inflammatory drugs and restricted exercise for a two-week period. The follow-up examination revealed only minimal improvement and therefore, the dog was referred for further diagnostic evaluation. Chronic bicipital tenosynovitis and tendinitis of the infraspinatus muscle was diagnosed based on survey radiographs, arthrography, ultrasound, computed tomography (CT), and synovial fluid cytology. The dog underwent three sessions of extracorporeal shockwave therapy and substantial clinical improvement was observed. On follow-up examinations, only mild left forelimb lameness was evident following exercise, and changes in the intertubercular groove and at the supraglenoid tuberosity appeared less active on radiographs and CT. However, six months following treatment, mild degenerative joint disease was apparent.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, David R.; Morrow, Benjamin M.; Trujillo, Carl P.

Here, we present a series of experiments probing the martensitic α–ω (hexagonal close-packed to simple hexagonal) transition in titanium under shock-loading to peak stresses around 15 GPa. Gas-gun plate impact techniques were used to locate the α–ω transition stress with a laser-based velocimetry diagnostic. A change in the shock-wave profile at 10.1 GPa suggests the transition begins at this stress. A second experiment shock-loaded and then soft-recovered a similar titanium sample. We then analyzed this recovered material with electron-backscatter diffraction methods, revealing on average approximately 65% retained ω phase. Furthermore, based on careful analysis of the microstructure, we propose thatmore » the titanium never reached a full ω state, and that there was no observed phase-reversion from ω to α. Texture analysis suggests that any α titanium found in the recovered sample is the original α. The data show that both the α and ω phases are stable and can coexist even though the shock-wave presents as steady-state, at these stresses.« less

Navier-Stokes structure of merged layer flow on the spherical nose of a space vehicle

NASA Technical Reports Server (NTRS)

Jain, A. C.; Woods, G. H.

1988-01-01

Hypersonic merged layer flow on the forepart of a spherical surface of a space vehicle has been investigated on the basis of the full steady-state Navier-Stokes equations using slip and temperature jump boundary conditions at the surface and free-stream conditions far from the surface. The shockwave-like structure was determined as part of the computations. Using an equivalent body concept, computations were carried out under conditions that the Aeroassist Flight Experiment (AFE) Vehicle would encounter at 15 and 20 seconds in its flight path. Emphasis was placed on understanding the basic nature of the flow structure under low density conditions. Particular attention was paid to the understanding of the structure of the outer shockwave-like region as the fluid expands around the sphere. Plots were drawn for flow profiles and surface characteristics to understand the role of dissipation processes in the merged layer of the spherical nose of the vehicle.

Infrasonic waves generated by supersonic auroral arcs

NASA Astrophysics Data System (ADS)

Pasko, Victor P.

2012-10-01

A finite-difference time-domain (FDTD) model of infrasound propagation in a realistic atmosphere is used to provide quantitative interpretation of infrasonic waves produced by auroral arcs moving with supersonic speed. The Lorentz force and Joule heating are discussed in the existing literature as primary sources producing infrasound waves in the frequency range 0.1-0.01 Hz associated with the auroral electrojet. The results are consistent with original ideas of Swift (1973) and demonstrate that the synchronization of the speed of auroral arc and phase speed of the acoustic wave in the electrojet volume is an important condition for generation of magnitudes and frequency contents of infrasonic waves observable on the ground. The reported modeling also allows accurate quantitative reproduction of previously observed complex infrasonic waveforms including direct shock and reflected shockwaves, which are refracted back to the earth by the thermosphere.

Implosion-driven technique to create fast shockwaves in high-density gas

NASA Astrophysics Data System (ADS)

Serge, Matthew; Loiseau, Jason; Huneault, Justin; Szirti, Daniel; Higgins, Andrew; Tanguay, Vincent

2012-03-01

Pressurized tubes surrounded by either one or two layers (separated by a secondary tube) of sensitized nitromethane and encased in a thick-walled tube (the tamper) were imploded. The distance between the detonation wave in the explosive and shock wave in the innermost tube were measured (the standoff). A simple model based on hoop stress and acoustic interactions between the tubing was developed and used to predict the standoff distance. At low initial pressures (on the order of 7MPa), results indicate that the secondary tube and two layers of explosive did not prove to significantly increase the standoff. However, at higher pressures (on the order of 10 MPa), standoff was noticeably greater when the secondary tube was inserted between the pressurized tube and the tamper. The measured values are in reasonable agreement with the predictions of the model.

The thermal and mechanical deformation study of up-stream pumping mechanical seal

NASA Astrophysics Data System (ADS)

Chen, H. L.; Xu, C.; Zuo, M. Z.; Wu, Q. B.

2015-01-01

Taking the viscosity-temperature relationship of the fluid film into consideration, a 3-D numerical model was established by ANSYS software which can simulate the heat transfer between the upstream pumping mechanical seal stationary and rotational rings and the fluid film between them as well as simulate the thermal deformation, structure deformation and the coupling deformation of them. According to the calculation result, thermal deformation causes the seal face expansion and the maximum thermal deformation appears at the inside of the seal ring. Pressure results in a mechanical deformation, the maximum deformation occurs at the top of the spiral groove and the overall trend is inward the mating face, opposite to the thermal deformation. The coupling deformation indicate that the thermal deformation can be partly counteracted by pressure deformation. Using this model, the relationship between deformation and shaft speed and the sealing liquid pressure was studied. It's found that the shaft speed will both enhance the thermal and structure deformation and the fluid pressure will enhance the structure deformation but has little to do with the thermal deformation. By changing the sealing material, it's found that material with low thermal expansion coefficient and low elastic modulus will suffer less thermal-pressure deformation.

Multilevel model of polycrystalline materials: grain boundary sliding description

NASA Astrophysics Data System (ADS)

Sharifullina, E.; Shveykin, A.; Trusov, P.

2017-12-01

Material behavior description in a wide range of thermomechanical effects is one of the topical areas in mathematical modeling. Inclusion of grain boundary sliding as an important mechanism of polycrystalline material deformation at elevated temperatures and predominant deformation mechanism of metals and alloys in structural superplasticity allows to simulate various deformation regimes and their transitions (including superplasticity regime with switch-on and switch-off regimes). The paper is devoted to description of grain boundary sliding in structure of two-level model, based on crystal plasticity, and relations for determination the contribution of this mechanism to inelastic deformation. Some results are presented concerning computational experiments of polycrystalline representative volume deformation using developed model.

Description of the Hexadecapole Deformation Parameter in the sdg Interacting Boson Model

NASA Astrophysics Data System (ADS)

Liu, Yu-xin; Sun, Di; Wang, Jia-jun; Han, Qi-zhi

1998-04-01

The hexadecapole deformation parameter β4 of the rare-earth and actinide nuclei is investigated in the framework of the sdg interacing boson model. An explicit relation between the geometric hexadecapole deformation parameter β4 and the intrinsic deformation parameters epsilon4, epsilon2 are obtained. The deformation parameters β4 of the rare-earths and actinides are determined without any free parameter. The calculated results agree with experimental data well. It also shows that the SU(5) limit of the sdg interacting boson model can describe the β4 systematics as well as the SU(3) limit.

Effects of Host-rock Fracturing on Elastic-deformation Source Models of Volcano Deflation.

PubMed

Holohan, Eoghan P; Sudhaus, Henriette; Walter, Thomas R; Schöpfer, Martin P J; Walsh, John J

2017-09-08

Volcanoes commonly inflate or deflate during episodes of unrest or eruption. Continuum mechanics models that assume linear elastic deformation of the Earth's crust are routinely used to invert the observed ground motions. The source(s) of deformation in such models are generally interpreted in terms of magma bodies or pathways, and thus form a basis for hazard assessment and mitigation. Using discontinuum mechanics models, we show how host-rock fracturing (i.e. non-elastic deformation) during drainage of a magma body can progressively change the shape and depth of an elastic-deformation source. We argue that this effect explains the marked spatio-temporal changes in source model attributes inferred for the March-April 2007 eruption of Piton de la Fournaise volcano, La Reunion. We find that pronounced deflation-related host-rock fracturing can: (1) yield inclined source model geometries for a horizontal magma body; (2) cause significant upward migration of an elastic-deformation source, leading to underestimation of the true magma body depth and potentially to a misinterpretation of ascending magma; and (3) at least partly explain underestimation by elastic-deformation sources of changes in sub-surface magma volume.

Representing Matrix Cracks Through Decomposition of the Deformation Gradient Tensor in Continuum Damage Mechanics Methods

NASA Technical Reports Server (NTRS)

Leone, Frank A., Jr.

2015-01-01

A method is presented to represent the large-deformation kinematics of intraply matrix cracks and delaminations in continuum damage mechanics (CDM) constitutive material models. The method involves the additive decomposition of the deformation gradient tensor into 'crack' and 'bulk material' components. The response of the intact bulk material is represented by a reduced deformation gradient tensor, and the opening of an embedded cohesive interface is represented by a normalized cohesive displacement-jump vector. The rotation of the embedded interface is tracked as the material deforms and as the crack opens. The distribution of the total local deformation between the bulk material and the cohesive interface components is determined by minimizing the difference between the cohesive stress and the bulk material stress projected onto the cohesive interface. The improvements to the accuracy of CDM models that incorporate the presented method over existing approaches are demonstrated for a single element subjected to simple shear deformation and for a finite element model of a unidirectional open-hole tension specimen. The material model is implemented as a VUMAT user subroutine for the Abaqus/Explicit finite element software. The presented deformation gradient decomposition method reduces the artificial load transfer across matrix cracks subjected to large shearing deformations, and avoids the spurious secondary failure modes that often occur in analyses based on conventional progressive damage models.

Visualizing along-strike change in deformation style using analog modeling and digital visualization software

NASA Astrophysics Data System (ADS)

Burberry, C. M.

2012-12-01

It is a well-known phenomenon that deformation style varies in space; both along the strike of a deformed belt and along the strike of individual structures within that belt. This variation in deformation style is traditionally visualized with a series of closely spaced 2D cross-sections. However, the use of 2D section lines implies plane strain along those lines, and the true 3D nature of the deformation is not necessarily captured. By using a combination of remotely sensed data, analog modeling of field datasets and this remote data, and numerical and digital visualization of the finished model, a 3D understanding and restoration of the deformation style within the region can be achieved. The workflow used for this study begins by considering the variation in deformation style which can be observed from satellite images and combining this data with traditional field data, in order to understand the deformation in the region under consideration. The conceptual model developed at this stage is then modeled using a sand and silicone modeling system, where the kinematics and dynamics of the deformation processes can be examined. A series of closely-spaced cross-sections, as well as 3D images of the deformation, are created from the analog model, and input into a digital visualization and modeling system for restoration. In this fashion, a valid 3D model is created where the internal structure of the deformed system can be visualized and mined for information. The region used in the study is the Sawtooth Range, Montana. The region forms part of the Montana Disturbed Belt in the Front Ranges of the Rocky Mountains, along strike from the Alberta Syncline in the Canadian Rocky Mountains. Interpretation of satellite data indicates that the deformation front structures include both folds and thrust structures. The thrust structures vary from hinterland-verging triangle zones to foreland-verging imbricate thrusts along strike, and the folds also vary in geometry along strike. The analog models, constrained by data from exploration wells, indicate that this change in geometry is related to a change in mechanical stratigraphy along the strike of the belt. Results from the kinematic and dynamic analysis of the digital model will also be presented. Additional implications of such a workflow and visualization system include the possibility of creating and viewing multiple cross-sections, including sections created at oblique angles to the original model. This allows the analysis of the non-plane strain component of the models and thus a more complete analysis, understanding and visualization of the deformed region. This workflow and visualization system is applicable to any region where traditional field methods must be coupled with remote data, intensely processed depth data, or analog modeling systems in order to generate valid geologic or geophsyical models.

Novel two-step laser ablation and ionization mass spectrometry (2S-LAIMS) of actor-spectator ice layers: Probing chemical composition of D{sub 2}O ice beneath a H{sub 2}O ice layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Rui, E-mail: ryang73@ustc.edu; Gudipati, Murthy S., E-mail: gudipati@jpl.nasa.gov

2014-03-14

In this work, we report for the first time successful analysis of organic aromatic analytes imbedded in D{sub 2}O ices by novel infrared (IR) laser ablation of a layered non-absorbing D{sub 2}O ice (spectator) containing the analytes and an ablation-active IR-absorbing H{sub 2}O ice layer (actor) without the analyte. With these studies we have opened up a new method for the in situ analysis of solids containing analytes when covered with an IR laser-absorbing layer that can be resonantly ablated. This soft ejection method takes advantage of the tenability of two-step infrared laser ablation and ultraviolet laser ionization mass spectrometry,more » previously demonstrated in this lab to study chemical reactions of polycyclic aromatic hydrocarbons (PAHs) in cryogenic ices. The IR laser pulse tuned to resonantly excite only the upper H{sub 2}O ice layer (actor) generates a shockwave upon impact. This shockwave penetrates the lower analyte-containing D{sub 2}O ice layer (spectator, a non-absorbing ice that cannot be ablated directly with the wavelength of the IR laser employed) and is reflected back, ejecting the contents of the D{sub 2}O layer into the vacuum where they are intersected by a UV laser for ionization and detection by a time-of-flight mass spectrometer. Thus, energy is transmitted from the laser-absorbing actor layer into the non-absorbing spectator layer resulting its ablation. We found that isotope cross-contamination between layers was negligible. We also did not see any evidence for thermal or collisional chemistry of PAH molecules with H{sub 2}O molecules in the shockwave. We call this “shockwave mediated surface resonance enhanced subsurface ablation” technique as “two-step laser ablation and ionization mass spectrometry of actor-spectator ice layers.” This method has its roots in the well-established MALDI (matrix assisted laser desorption and ionization) method. Our method offers more flexibility to optimize both the processes—ablation and ionization. This new technique can thus be potentially employed to undertake in situ analysis of materials imbedded in diverse media, such as cryogenic ices, biological samples, tissues, minerals, etc., by covered with an IR-absorbing laser ablation medium and study the chemical composition and reaction pathways of the analyte in its natural surroundings.« less

Inference of postseismic deformation mechanisms of the 1923 Kanto earthquake

USGS Publications Warehouse

Pollitz, F.F.; Nyst, M.; Nishimura, T.; Thatcher, W.

2006-01-01

Coseismic slip associated with the M7.9, 1923 Kanto earthquake is fairly well understood, involving slip of up to 8 m along the Philippine Sea-Honshu interplate boundary under Sagami Bay and its onland extension. Postseismic deformation after the 1923 earthquake, however, is relatively poorly understood. We revisit the available deformation data in order to constrain possible mechanisms of postseismic deformation and to examine the consequences for associated stress changes in the surrounding crust. Data from two leveling lines and one tide gage station over the first 7-8 years postseismic period are of much greater amplitude than the corresponding expected interseismic deformation during the same period, making these data suitable for isolating the signal from postseismic deformation. We consider both viscoelastic models of asthenosphere relaxation and afterslip models. A distributed coseismic slip model presented by Pollitz et al. (2005), combined with prescribed parameters of a viscoelastic Earth model, yields predicted postseismic deformation that agrees with observed deformation on mainland Honshu from Tokyo to the Izu peninsula. Elsewhere (southern Miura peninsula; Boso peninsula), the considered viscoelastic models fail to predict observed deformation, and a model of ???1 in shallow afterslip in the offshore region south of the Boso peninsula, with equivalent moment magnitude Mw = 7.0, adequately accounts for the observed deformation. Using the distributed coseismic slip model, layered viscoelastic structure, and a model of interseismic strain accumulation, we evaluate the post-1923 stress evolution, including both the coseismic and accumulated postseismic stress changes and those stresses contributed by interseismic loading. We find that if account is made for the varying tectonic regime in the region, the occurrence of both immediate (first month) post-1923 crustal aftershocks as well as recent regional crustal seismicity is consistent with the predicted stress pattern. This suggests that the influence of the 1923 earthquake on regional seismicity is fairly predictable and has persisted for at least seven decades following the earthquake.

Simulation of high-temperature superlocalization of plastic deformation in single-crystals of alloys with an L12 superstructure

NASA Astrophysics Data System (ADS)

Solov'eva, Yu. V.; Fakhrutdinova, Ya. D.; Starenchenko, V. A.

2015-01-01

The processes of the superlocalization of plastic deformation in L12 alloys have been studied numerically based on a combination of the model of the dislocation kinetics of the deformation-induced and heat-treatment-induced strengthening of an element of a deformable medium with the model of the mechanics of microplastic deformation described in terms of elastoplastic medium. It has been shown that the superlocalization of plastic deformation is determined by the presence of stress concentrators and by the nonmonotonic strengthening of the elements of the deformable medium. The multiple nonmonotonicity of the process of strengthening of the elementary volume of the medium can be responsible for the multiplicity of bands of microplastic localization of deformation.

Wind-US Code Physical Modeling Improvements to Complement Hypersonic Testing and Evaluation

NASA Technical Reports Server (NTRS)

Georgiadis, Nicholas J.; Yoder, Dennis A.; Towne, Charles S.; Engblom, William A.; Bhagwandin, Vishal A.; Power, Greg D.; Lankford, Dennis W.; Nelson, Christopher C.

2009-01-01

This report gives an overview of physical modeling enhancements to the Wind-US flow solver which were made to improve the capabilities for simulation of hypersonic flows and the reliability of computations to complement hypersonic testing. The improvements include advanced turbulence models, a bypass transition model, a conjugate (or closely coupled to vehicle structure) conduction-convection heat transfer capability, and an upgraded high-speed combustion solver. A Mach 5 shock-wave boundary layer interaction problem is used to investigate the benefits of k- s and k-w based explicit algebraic stress turbulence models relative to linear two-equation models. The bypass transition model is validated using data from experiments for incompressible boundary layers and a Mach 7.9 cone flow. The conjugate heat transfer method is validated for a test case involving reacting H2-O2 rocket exhaust over cooled calorimeter panels. A dual-mode scramjet configuration is investigated using both a simplified 1-step kinetics mechanism and an 8-step mechanism. Additionally, variations in the turbulent Prandtl and Schmidt numbers are considered for this scramjet configuration.

Silicate Liquid Equations of State from Molten Shock Experiments

NASA Astrophysics Data System (ADS)

Asimow, P. D.; Ahrens, T. J.

2005-12-01

Over the past 20 years the Caltech shockwave lab has pioneered the direct measurement of equations of state of silicate liquids by shockwave experiments on targets preheated to 1250-1700 °C. A glass of the desired composition is welded into a Mo capsule; the capsule is heated by induction to above the liquidus of the sample. Upon impact with a gun-launched flyer plate, a planar shockwave is driven into the molten sample. Passage of the shock through the sample and capsule cover is measured with a high-speed streak camera; impactor velocity is measured with a double-exposure flash X-ray. Initial sample density is inferred from measured temperature and known 1 bar density and thermal expansion data. Previously, a 40 mm single-stage gun launched 80 g projectiles carrying 1.5 mm thick flyers at up to 2.7 km/s. Maximum pressures in the range of 25 to 45 GPa were achieved in diopside, anorthite, the diopside-anorthite eutectic, komatiite, MORB, and fayalite. Results of prior work are briefly reviewed. Also revisited are arguments that, although the silicate liquids achieve their relaxed hydrostatic states, crystallization does not occur on the timescale of the experiment. Densities of the compositions studied appear to converge in the 20-40 GPa range to that expected for a mixture of dense oxide phases of equal composition and temperature. Previous data, however, do not test whether, with further compression, the liquids can become denser than the equivalent solid oxide mixes. In the case of the diopside-anorthite eutectic, earlier experiments showed anomalous stiffening above 25 GPa. We have improved the technique in several ways that allow us to extend measurements to pressures exceeding the core-mantle boundary in the Earth. These improvements include a higher writing-rate image converter streak camera, high-temperature shorting pins to trigger the image converter camera, digital profiling of pre-shot capsule shape, pyrometry (in place of thermocouples) to measure pre-shot temperature, better heating coil design for more uniform heating, initiation of a program to extent Hugoniot data on hot Mo, and (most importantly) adaptation to Caltech's 25 mm two-stage light gas gun for impact speeds up to 7.5 km/s. We intend to apply this technique to characterize a suite of liquid compositions up to core-mantle boundary pressure in order to constrain melting relationships and dynamics of partial melts under magma ocean and ultra-low velocity zone conditions. Such large compressions will also clearly test whether the hot dense oxide mix model is useful for extrapolating liquid properties beyond the mid-mantle. Initial results have revisited the anomalous compression of diopside-anorthite eutectic composition above 25 GPa. A single experiment reaching 42 GPa clearly lies on the extension of the low pressure Hugoniot and shows, at the 10 sigma level, that the anomalous compression of this composition is not repeatable. An error-weighted fit to all the data on this composition is consistent with a linear Us-Up Hugoniot. We expect that shockwave studies of silicate liquids will constitute a key element of a renewed effort in the broader community to determine physical properties of liquids at all mantle pressures and to apply this knowledge to understanding the differentiation and current state of the Earth.

Stress and deformation characteristics of sea ice in a high resolution numerical sea ice model.

NASA Astrophysics Data System (ADS)

Heorton, Harry; Feltham, Daniel; Tsamados, Michel

2017-04-01

The drift and deformation of sea ice floating on the polar oceans is due to the applied wind and ocean currents. The deformations of sea ice over ocean basin length scales have observable patterns; cracks and leads in satellite images and within the velocity fields generated from floe tracking. In a climate sea ice model the deformation of sea ice over ocean basin length scales is modelled using a rheology that represents the relationship between stresses and deformation within the sea ice cover. Here we investigate the link between observable deformation characteristics and the underlying internal sea ice stresses and force balance using the Los Alamos numerical sea ice climate model. In order to mimic laboratory experiments on the deformation of small cubes of sea ice we have developed an idealised square domain that tests the model response at spatial resolutions of up to 500m. We use the Elastic Anisotropic Plastic and Elastic Viscous Plastic rheologies, comparing their stability over varying resolutions and time scales. Sea ice within the domain is forced by idealised winds in order to compare the confinement of wind stresses and internal sea ice stresses. We document the characteristic deformation patterns of convergent, divergent and rotating stress states.

Investigation of the effects of aeroelastic deformations on the radar cross section of aircraft

NASA Astrophysics Data System (ADS)

McKenzie, Samuel D.

1991-12-01

The effects of aeroelastic deformations on the radar cross section (RCS) of a T-38 trainer jet and a C-5A transport aircraft are examined and characterized. Realistic representations of structural wing deformations are obtained from a mechanical/computer aided design software package called NASTRAN. NASTRAN is used to evaluate the structural parameters of the aircraft as well as the restraints and loads associated with realistic flight conditions. Geometries for both the non-deformed and deformed airframes are obtained from the NASTRAN models and translated into RCS models. The RCS is analyzed using a numerical modeling code called the Radar Cross Section - Basic Scattering Code, version 2 which was developed at the Ohio State University and is based on the uniform geometric theory of diffraction. The code is used to analyze the effects of aeroelastic deformations on the RCS of the aircraft by comparing the computed RCS representing the deformed airframe to that of the non-deformed airframe and characterizing the differences between them.

Elastic plastic self-consistent (EPSC) modeling of plastic deformation in fayalite olivine

DOE PAGES

Burnley, Pamela C

2015-07-01

Elastic plastic self-consistent (EPSC) simulations are used to model synchrotron X-ray diffraction observations from deformation experiments on fayalite olivine using the deformation DIA apparatus. Consistent with results from other in situ diffraction studies of monomineralic polycrystals, the results show substantial variations in stress levels among grain populations. Rather than averaging the lattice reflection stresses or choosing a single reflection to determine the macroscopic stress supported by the specimen, an EPSC simulation is used to forward model diffraction data and determine a macroscopic stress that is consistent with lattice strains of all measured diffraction lines. The EPSC simulation presented here includesmore » kink band formation among the plastic deformation mechanisms in the simulation. The inclusion of kink band formation is critical to the success of the models. This study demonstrates the importance of kink band formation as an accommodation mechanism during plastic deformation of olivine as well as the utility of using EPSC models to interpret diffraction from in situ deformation experiments.« less

Micromechanical constitutive model for low-temperature constant strain rate deformation of limestones in the brittle and semi-brittle regime

NASA Astrophysics Data System (ADS)

Nicolas, A.; Fortin, J.; Guéguen, Y.

2017-10-01

Deformation and failure of rocks are important for a better understanding of many crustal geological phenomena such as faulting and compaction. In carbonate rocks among others, low-temperature deformation can either occur with dilatancy or compaction, having implications for porosity changes, failure and petrophysical properties. Hence, a thorough understanding of all the micromechanisms responsible for deformation is of great interest. In this study, a constitutive model for the low-temperature deformation of low-porosity (<20 per cent) carbonate rocks is derived from the micromechanisms identified in previous studies. The micromechanical model is based on (1) brittle crack propagation, (2) a plasticity law (interpreted in terms of dislocation glide without possibility to climb) for porous media with hardening and (3) crack nucleation due to dislocation pile-ups. The model predicts stress-strain relations and the evolution of damage during deformation. The model adequately predicts brittle behaviour at low confining pressures, which switches to a semi-brittle behaviour characterized by inelastic compaction followed by dilatancy at higher confining pressures. Model predictions are compared to experimental results from previous studies and are found to be in close agreement with experimental results. This suggests that microphysical phenomena responsible for the deformation are sufficiently well captured by the model although twinning, recovery and cataclasis are not considered. The porosity range of applicability and limits of the model are discussed.

Soft tissue modelling through autowaves for surgery simulation.

PubMed

Zhong, Yongmin; Shirinzadeh, Bijan; Alici, Gursel; Smith, Julian

2006-09-01

Modelling of soft tissue deformation is of great importance to virtual reality based surgery simulation. This paper presents a new methodology for simulation of soft tissue deformation by drawing an analogy between autowaves and soft tissue deformation. The potential energy stored in a soft tissue as a result of a deformation caused by an external force is propagated among mass points of the soft tissue by non-linear autowaves. The novelty of the methodology is that (i) autowave techniques are established to describe the potential energy distribution of a deformation for extrapolating internal forces, and (ii) non-linear materials are modelled with non-linear autowaves other than geometric non-linearity. Integration with a haptic device has been achieved to simulate soft tissue deformation with force feedback. The proposed methodology not only deals with large-range deformations, but also accommodates isotropic, anisotropic and inhomogeneous materials by simply changing diffusion coefficients.

Laser-generated shockwaves enhance antibacterial activity against biofilms in vitro.

PubMed

Yao, William; Kuan, Edward C; Francis, Nathan C; St John, Maie A; Grundfest, Warren S; Taylor, Zachary D

2017-07-01

Bacterial biofilm formation within chronic wound beds, which provides an effective barrier against antibiotics, is a known cause of recalcitrant infections and a significant healthcare burden, often requiring repeated surgical debridements. Laser-generated shockwaves (LGS) is a novel, minimally invasive, and nonthermal modality for biofilm mechanical debridement which utilizes compressive stress waves, generated by photonic absorption in thin titanium films to mechanically disrupt the biofilm. Prior studies have demonstrated LGS monotherapy to be selectively efficacious for biofilm disruption and safe for host tissues. In this study, we sought to determine if LGS can enhance the antimicrobial activity and biofilm disruption capability of topical antibiotic therapy. Staphylococcus epidermidis biofilms grown in vitro on glass were treated with topical gentamicin (31, 62, and 124 μg/ml) with and without LGS (n = 3-11/treatment group). Mechanical shockwaves were generated with a 1,064 nm Nd:YAG laser (laser fluence 110.14 mJ/mm 2 , pulse duration 5 ns, spot size 3 mm). Following a 24-hour incubation period, bacterial viability was assessed by determining the number of colony-forming units (CFU) via the Miles and Misra method. Residual biofilm bioburden was analyzed using the crystal violet biofilm assay. With gentamicin monotherapy, CFU density (CFU/mm 2 ) at 31, 62, and 124 μg/ml were (282 ± 84) × 10 4 , (185 ± 34) × 10 4 , and (113 ± 9) × 10 4 , respectively. With LGS and gentamicin therapy, CFU density decreased to (170 ± 44) × 10 4 , (89 ± 24) × 10 4 , and (43 ± 3) × 10 4 , respectively (P = 0.1704, 0.0302, and 0.0004 when compared with gentamicin alone). Biofilm burden as measured by the assay in the gentamicin 31, 62, and 124 μg/ml groups was reduced by 80%, 95%, and 98% when LGS was added (P = 0.0102, >0.0001, and 0.0001 for all groups when compared with gentamicin alone). Furthermore, samples treated with LGS saw an increase in susceptibility to gentamicin, in terms of reduced biofilm bioburden and CFU densities. LGS enhances the efficacy of topical antibiotics in an in vitro model. This has significant implications for clinical applications in the management of chronic soft tissue infections and recalcitrant chronic rhinosinusitis. Lasers Surg. Med. 49:539-547, 2017. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

A transverse isotropic viscoelastic constitutive model for aortic valve tissue

PubMed Central

Bucchi, Andrea; Screen, Hazel R. C.; Evans, Sam L.

2017-01-01

A new anisotropic viscoelastic model is developed for application to the aortic valve (AV). The directional dependency in the mechanical properties of the valve, arising from the predominantly circumferential alignment of collagen fibres, is accounted for in the form of transverse isotropy. The rate dependency of the valve's mechanical behaviour is considered to stem from the viscous (η) dissipative effects of the AV matrix, and is incorporated as an explicit function of the deformation rate (λ˙). Model (material) parameters were determined from uniaxial tensile deformation tests of porcine AV specimens at various deformation rates, by fitting the model to each experimental dataset. It is shown that the model provides an excellent fit to the experimental data across all different rates and satisfies the condition of strict local convexity. Based on the fitting results, a nonlinear relationship between η and λ˙ is established, highlighting a ‘shear-thinning’ behaviour for the AV with increase in the deformation rate. Using the model and these outcomes, the stress–deformation curves of the AV tissue under physiological deformation rates in both the circumferential and radial directions are predicted and presented. To verify the predictive capabilities of the model, the stress–deformation curves of AV specimens at an intermediate deformation rate were estimated and validated against the experimental data at that rate, showing an excellent agreement. While the model is primarily developed for application to the AV, it may be applied without the loss of generality to other collagenous soft tissues possessing a similar structure, with a single preferred direction of embedded collagen fibres. PMID:28280556

MEASURING HYDROLOGICAL CHANGE DURING EXURBAN DEVELOPMENT: COLLABORATIVE HYDROLOGIC RESEARCH IN THE CLARKSBURG SPECIAL PROTECTION AREA

EPA Science Inventory

This research project is focused on the Clarksburg Special Protection Area (CSPA) in Montgomery County, Maryland. The CSPA subwatersheds are on the outer edge of the exurban development shockwave expanding outward from the Washington DC metropolitan area. The CSPA is an area of ...

MEASURING HYDROLOGICAL CHANGE DURING EXURBAN DEVELOPMENT: COLLABORATIVE HYDROLOGIC RESEARCH IN THE CLARKSBURG SPECIAL PROTECTION AREA

EPA Science Inventory

This research project is focused on the Clarksburg Special Protection Area (CSPA) in Montgomery County, Maryland. The CSPA subwatersheds are on the outer edge of the exurban development shockwave expanding outward from the Washington, DC, metropolitan area. The CSPA is an area o...

COLLABORATIVE SCIENCE FOR ENVIRONMENTAL SOLUTIONS: COLLABORATIVE HYDROLOGIC RESEARCH IN THE CLARKSBURG SPECIAL PROTECTION AREA

EPA Science Inventory

This research project is focused on the Clarksburg Special Protection Area (CSPA) in Montgomery County, Maryland. The CSPA subwatersheds are on the outer edge of the exurban development shockwave expanding outward from the Washington DC metropolitan area. The CSPA is an area of...

Treatment of Standardized Fractures by Extracorporeal Shockwave Therapy (ESWT)

DTIC Science & Technology

2001-10-25

prostate carcinoma and melanomas [4,7,18,19]. Having an analgesic effect, shock waves, are also used in treatment of tendinosis calcarea, tennis ... elbow and heel spurs [6,11,15]. Another application area for ESWT is pseudoarthrosis [9,12,13]. In bone tissue, ESWT imitates a fresh fracture

The 2010 Canterbury Earthquake: Curriculum Shockwaves

ERIC Educational Resources Information Center

Taylor, Mike; Moeed, Azra

2013-01-01

This paper reports data from an exploratory questionnaire designed to capture "curriculum P-waves"--those curriculum responses that were the fastest and therefore measured first--following a significant earthquake in New Zealand. As well as taking a professional interest in a major disaster in their backyard, it is assumed that social…

Signal Processing of Shock-Wave Overpressure Records

DTIC Science & Technology

1981-08-01

SUPERPOSED GAGE-MOUNT RINGING. UNCLASSIFIED FIG. . FORIERSPECRUM O AN - WAV WIT SUPRPSE GAE-OUT RNGNG UNCLASSIFIED SM No. 1021 󈨏- 925 Pa E 0. 00 0"a... midi rfit-valotinrent pmn -ri or grant number oquiprancr mcxlel designation. firnite iamem. militlary project codte irlri ir. I, tir, IlII. 46winl

Tenderization of beef loins using a high efficiency sparker

USDA-ARS?s Scientific Manuscript database

The objective of this study was to determine the effectiveness of tenderizing beef strip loins using high-pressure shockwaves generated from a sparker source. A total of 117 steaks from 16 beef strip loins were utilized with each treated steak having an adjacent steak as a non-treated control. Ste...

Multiscale Modeling of Polycrystalline NiTi Shape Memory Alloy under Various Plastic Deformation Conditions by Coupling Microstructure Evolution and Macroscopic Mechanical Response

PubMed Central

Jiang, Shuyong; Zhou, Tao; Tu, Jian; Shi, Laixin; Chen, Qiang; Yang, Mingbo

2017-01-01

Numerical modeling of microstructure evolution in various regions during uniaxial compression and canning compression of NiTi shape memory alloy (SMA) are studied through combined macroscopic and microscopic finite element simulation in order to investigate plastic deformation of NiTi SMA at 400 °C. In this approach, the macroscale material behavior is modeled with a relatively coarse finite element mesh, and then the corresponding deformation history in some selected regions in this mesh is extracted by the sub-model technique of finite element code ABAQUS and subsequently used as boundary conditions for the microscale simulation by means of crystal plasticity finite element method (CPFEM). Simulation results show that NiTi SMA exhibits an inhomogeneous plastic deformation at the microscale. Moreover, regions that suffered canning compression sustain more homogeneous plastic deformation by comparison with the corresponding regions subjected to uniaxial compression. The mitigation of inhomogeneous plastic deformation contributes to reducing the statistically stored dislocation (SSD) density in polycrystalline aggregation and also to reducing the difference of stress level in various regions of deformed NiTi SMA sample, and therefore sustaining large plastic deformation in the canning compression process. PMID:29027925

Multiscale Modeling of Polycrystalline NiTi Shape Memory Alloy under Various Plastic Deformation Conditions by Coupling Microstructure Evolution and Macroscopic Mechanical Response.

PubMed

Hu, Li; Jiang, Shuyong; Zhou, Tao; Tu, Jian; Shi, Laixin; Chen, Qiang; Yang, Mingbo

2017-10-13

Numerical modeling of microstructure evolution in various regions during uniaxial compression and canning compression of NiTi shape memory alloy (SMA) are studied through combined macroscopic and microscopic finite element simulation in order to investigate plastic deformation of NiTi SMA at 400 °C. In this approach, the macroscale material behavior is modeled with a relatively coarse finite element mesh, and then the corresponding deformation history in some selected regions in this mesh is extracted by the sub-model technique of finite element code ABAQUS and subsequently used as boundary conditions for the microscale simulation by means of crystal plasticity finite element method (CPFEM). Simulation results show that NiTi SMA exhibits an inhomogeneous plastic deformation at the microscale. Moreover, regions that suffered canning compression sustain more homogeneous plastic deformation by comparison with the corresponding regions subjected to uniaxial compression. The mitigation of inhomogeneous plastic deformation contributes to reducing the statistically stored dislocation (SSD) density in polycrystalline aggregation and also to reducing the difference of stress level in various regions of deformed NiTi SMA sample, and therefore sustaining large plastic deformation in the canning compression process.

Poisson-Lie duals of the η deformed symmetric space sigma model

NASA Astrophysics Data System (ADS)

Hoare, Ben; Seibold, Fiona K.

2017-11-01

Poisson-Lie dualising the η deformation of the G/H symmetric space sigma model with respect to the simple Lie group G is conjectured to give an analytic continuation of the associated λ deformed model. In this paper we investigate when the η deformed model can be dualised with respect to a subgroup G0 of G. Starting from the first-order action on the complexified group and integrating out the degrees of freedom associated to different subalgebras, we find it is possible to dualise when G0 is associated to a sub-Dynkin diagram. Additional U1 factors built from the remaining Cartan generators can also be included. The resulting construction unifies both the Poisson-Lie dual with respect to G and the complete abelian dual of the η deformation in a single framework, with the integrated algebras unimodular in both cases. We speculate that extending these results to the path integral formalism may provide an explanation for why the η deformed AdS5 × S5 superstring is not one-loop Weyl invariant, that is the couplings do not solve the equations of type IIB supergravity, yet its complete abelian dual and the λ deformed model are.

Application of the Deformation Information System for automated analysis and mapping of mining terrain deformations - case study from SW Poland

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Grzempowski, Piotr; Milczarek, Wojciech; Nowacka, Anna

2015-04-01

Monitoring, mapping and modelling of mining induced terrain deformations are important tasks for quantifying and minimising threats that arise from underground extraction of useful minerals and affect surface infrastructure, human safety, the environment and security of the mining operation itself. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and expanding with the progress in geographical information technologies. These include for example: terrestrial geodetic measurements, Global Navigation Satellite Systems, remote sensing, GIS based modelling and spatial statistics, finite element method modelling, geological modelling, empirical modelling using e.g. the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The presentation shows the results of numerical modelling and mapping of mining terrain deformations for two cases of underground mining sites in SW Poland, hard coal one (abandoned) and copper ore (active) using the functionalities of the Deformation Information System (DIS) (Blachowski et al, 2014 @ http://meetingorganizer.copernicus.org/EGU2014/EGU2014-7949.pdf). The functionalities of the spatial data modelling module of DIS have been presented and its applications in modelling, mapping and visualising mining terrain deformations based on processing of measurement data (geodetic and GNSS) for these two cases have been characterised and compared. These include, self-developed and implemented in DIS, automation procedures for calculating mining terrain subsidence with different interpolation techniques, calculation of other mining deformation parameters (i.e. tilt, horizontal displacement, horizontal strain and curvature), as well as mapping mining terrain categories based on classification of the values of these parameters as used in Poland. Acknowledgments. This work has been financed from the National Science Centre Project "Development of a numerical method of mining ground deformation modelling in complex geological and mining conditions" UMO-2012/07/B/ST10/04297 executed at the Faculty of Geoengineering, Mining and Geology of the Wroclaw University of Technology (Poland).

Large-scale deformation associated with ridge subduction

USGS Publications Warehouse

Geist, E.L.; Fisher, M.A.; Scholl, D. W.

1993-01-01

Continuum models are used to investigate the large-scale deformation associated with the subduction of aseismic ridges. Formulated in the horizontal plane using thin viscous sheet theory, these models measure the horizontal transmission of stress through the arc lithosphere accompanying ridge subduction. Modelling was used to compare the Tonga arc and Louisville ridge collision with the New Hebrides arc and d'Entrecasteaux ridge collision, which have disparate arc-ridge intersection speeds but otherwise similar characteristics. Models of both systems indicate that diffuse deformation (low values of the effective stress-strain exponent n) are required to explain the observed deformation. -from Authors

Videogrammetric Model Deformation Measurement Technique

NASA Technical Reports Server (NTRS)

Burner, A. W.; Liu, Tian-Shu

2001-01-01

The theory, methods, and applications of the videogrammetric model deformation (VMD) measurement technique used at NASA for wind tunnel testing are presented. The VMD technique, based on non-topographic photogrammetry, can determine static and dynamic aeroelastic deformation and attitude of a wind-tunnel model. Hardware of the system includes a video-rate CCD camera, a computer with an image acquisition frame grabber board, illumination lights, and retroreflective or painted targets on a wind tunnel model. Custom software includes routines for image acquisition, target-tracking/identification, target centroid calculation, camera calibration, and deformation calculations. Applications of the VMD technique at five large NASA wind tunnels are discussed.

[Research progress on real-time deformable models of soft tissues for surgery simulation].

PubMed

Xu, Shaoping; Liu, Xiaoping; Zhang, Hua; Luo, Jie

2010-04-01

Biological tissues generally exhibit nonlinearity, anisotropy, quasi-incompressibility and viscoelasticity about material properties. Simulating the behaviour of elastic objects in real time is one of the current objectives of virtual surgery simulation which is still a challenge for researchers to accurately depict the behaviour of human tissues. In this paper, we present a classification of the different deformable models that have been developed. We present the advantages and disadvantages of each one. Finally, we make a comparison of deformable models and perform an evaluation of the state of the art and the future of deformable models.

Latent log-linear models for handwritten digit classification.

PubMed

Deselaers, Thomas; Gass, Tobias; Heigold, Georg; Ney, Hermann

2012-06-01

We present latent log-linear models, an extension of log-linear models incorporating latent variables, and we propose two applications thereof: log-linear mixture models and image deformation-aware log-linear models. The resulting models are fully discriminative, can be trained efficiently, and the model complexity can be controlled. Log-linear mixture models offer additional flexibility within the log-linear modeling framework. Unlike previous approaches, the image deformation-aware model directly considers image deformations and allows for a discriminative training of the deformation parameters. Both are trained using alternating optimization. For certain variants, convergence to a stationary point is guaranteed and, in practice, even variants without this guarantee converge and find models that perform well. We tune the methods on the USPS data set and evaluate on the MNIST data set, demonstrating the generalization capabilities of our proposed models. Our models, although using significantly fewer parameters, are able to obtain competitive results with models proposed in the literature.

Medial-based deformable models in nonconvex shape-spaces for medical image segmentation.

PubMed

McIntosh, Chris; Hamarneh, Ghassan

2012-01-01

We explore the application of genetic algorithms (GA) to deformable models through the proposition of a novel method for medical image segmentation that combines GA with nonconvex, localized, medial-based shape statistics. We replace the more typical gradient descent optimizer used in deformable models with GA, and the convex, implicit, global shape statistics with nonconvex, explicit, localized ones. Specifically, we propose GA to reduce typical deformable model weaknesses pertaining to model initialization, pose estimation and local minima, through the simultaneous evolution of a large number of models. Furthermore, we constrain the evolution, and thus reduce the size of the search-space, by using statistically-based deformable models whose deformations are intuitive (stretch, bulge, bend) and are driven in terms of localized principal modes of variation, instead of modes of variation across the entire shape that often fail to capture localized shape changes. Although GA are not guaranteed to achieve the global optima, our method compares favorably to the prevalent optimization techniques, convex/nonconvex gradient-based optimizers and to globally optimal graph-theoretic combinatorial optimization techniques, when applied to the task of corpus callosum segmentation in 50 mid-sagittal brain magnetic resonance images.

A Biomechanical Modeling Guided CBCT Estimation Technique

PubMed Central

Zhang, You; Tehrani, Joubin Nasehi; Wang, Jing

2017-01-01

Two-dimensional-to-three-dimensional (2D-3D) deformation has emerged as a new technique to estimate cone-beam computed tomography (CBCT) images. The technique is based on deforming a prior high-quality 3D CT/CBCT image to form a new CBCT image, guided by limited-view 2D projections. The accuracy of this intensity-based technique, however, is often limited in low-contrast image regions with subtle intensity differences. The solved deformation vector fields (DVFs) can also be biomechanically unrealistic. To address these problems, we have developed a biomechanical modeling guided CBCT estimation technique (Bio-CBCT-est) by combining 2D-3D deformation with finite element analysis (FEA)-based biomechanical modeling of anatomical structures. Specifically, Bio-CBCT-est first extracts the 2D-3D deformation-generated displacement vectors at the high-contrast anatomical structure boundaries. The extracted surface deformation fields are subsequently used as the boundary conditions to drive structure-based FEA to correct and fine-tune the overall deformation fields, especially those at low-contrast regions within the structure. The resulting FEA-corrected deformation fields are then fed back into 2D-3D deformation to form an iterative loop, combining the benefits of intensity-based deformation and biomechanical modeling for CBCT estimation. Using eleven lung cancer patient cases, the accuracy of the Bio-CBCT-est technique has been compared to that of the 2D-3D deformation technique and the traditional CBCT reconstruction techniques. The accuracy was evaluated in the image domain, and also in the DVF domain through clinician-tracked lung landmarks. PMID:27831866

Biomechanical Model for Computing Deformations for Whole-Body Image Registration: A Meshless Approach

PubMed Central

Li, Mao; Miller, Karol; Joldes, Grand Roman; Kikinis, Ron; Wittek, Adam

2016-01-01

Patient-specific biomechanical models have been advocated as a tool for predicting deformations of soft body organs/tissue for medical image registration (aligning two sets of images) when differences between the images are large. However, complex and irregular geometry of the body organs makes generation of patient-specific biomechanical models very time consuming. Meshless discretisation has been proposed to solve this challenge. However, applications so far have been limited to 2-D models and computing single organ deformations. In this study, 3-D comprehensive patient-specific non-linear biomechanical models implemented using Meshless Total Lagrangian Explicit Dynamics (MTLED) algorithms are applied to predict a 3-D deformation field for whole-body image registration. Unlike a conventional approach which requires dividing (segmenting) the image into non-overlapping constituents representing different organs/tissues, the mechanical properties are assigned using the Fuzzy C-Means (FCM) algorithm without the image segmentation. Verification indicates that the deformations predicted using the proposed meshless approach are for practical purposes the same as those obtained using the previously validated finite element models. To quantitatively evaluate the accuracy of the predicted deformations, we determined the spatial misalignment between the registered (i.e. source images warped using the predicted deformations) and target images by computing the edge-based Hausdorff distance. The Hausdorff distance-based evaluation determines that our meshless models led to successful registration of the vast majority of the image features. PMID:26791945

On integrability of the Yang-Baxter {sigma}-model

DOE Office of Scientific and Technical Information (OSTI.GOV)

Klimcik, Ctirad

2009-04-15

We prove that the recently introduced Yang-Baxter {sigma}-model can be considered as an integrable deformation of the principal chiral model. We find also an explicit one-to-one map transforming every solution of the principal chiral model into a solution of the deformed model. With the help of this map, the standard procedure of the dressing of the principal chiral solutions can be directly transferred into the deformed Yang-Baxter context.

High-temperature behavior of a deformed Fermi gas obeying interpolating statistics.

PubMed

Algin, Abdullah; Senay, Mustafa

2012-04-01

An outstanding idea originally introduced by Greenberg is to investigate whether there is equivalence between intermediate statistics, which may be different from anyonic statistics, and q-deformed particle algebra. Also, a model to be studied for addressing such an idea could possibly provide us some new consequences about the interactions of particles as well as their internal structures. Motivated mainly by this idea, in this work, we consider a q-deformed Fermi gas model whose statistical properties enable us to effectively study interpolating statistics. Starting with a generalized Fermi-Dirac distribution function, we derive several thermostatistical functions of a gas of these deformed fermions in the thermodynamical limit. We study the high-temperature behavior of the system by analyzing the effects of q deformation on the most important thermostatistical characteristics of the system such as the entropy, specific heat, and equation of state. It is shown that such a deformed fermion model in two and three spatial dimensions exhibits the interpolating statistics in a specific interval of the model deformation parameter 0 < q < 1. In particular, for two and three spatial dimensions, it is found from the behavior of the third virial coefficient of the model that the deformation parameter q interpolates completely between attractive and repulsive systems, including the free boson and fermion cases. From the results obtained in this work, we conclude that such a model could provide much physical insight into some interacting theories of fermions, and could be useful to further study the particle systems with intermediate statistics.

Modeling of macrosegregation caused by volumetric deformation in a coherent mushy zone

NASA Astrophysics Data System (ADS)

Nicolli, Lilia C.; Mo, Asbjørn; M'hamdi, Mohammed

2005-02-01

A two-phase volume-averaged continuum model is presented that quantifies macrosegregation formation during solidification of metallic alloys caused by deformation of the dendritic network and associated melt flow in the coherent part of the mushy zone. Also, the macrosegregation formation associated with the solidification shrinkage (inverse segregation) is taken into account. Based on experimental evidence established elsewhere, volumetric viscoplastic deformation (densification/dilatation) of the coherent dendritic network is included in the model. While the thermomechanical model previously outlined (M. M’Hamdi, A. Mo, and C.L. Martin: Metall. Mater. Trans. A, 2002, vol. 33A, pp. 2081-93) has been used to calculate the temperature and velocity fields associated with the thermally induced deformations and shrinkage driven melt flow, the solute conservation equation including both the liquid and a solid volume-averaged velocity is solved in the present study. In modeling examples, the macrosegregation formation caused by mechanically imposed as well as by thermally induced deformations has been calculated. The modeling results for an Al-4 wt pct Cu alloy indicate that even quite small volumetric strains (≈2 pct), which can be associated with thermally induced deformations, can lead to a macroscopic composition variation in the final casting comparable to that resulting from the solidification shrinkage induced melt flow. These results can be explained by the relatively large volumetric viscoplastic deformation in the coherent mush resulting from the applied constitutive model, as well as the relatively large difference in composition for the studied Al-Cu alloy in the solid and liquid phases at high solid fractions at which the deformation takes place.

Reconstructing 3D Face Model with Associated Expression Deformation from a Single Face Image via Constructing a Low-Dimensional Expression Deformation Manifold.

PubMed

Wang, Shu-Fan; Lai, Shang-Hong

2011-10-01

Facial expression modeling is central to facial expression recognition and expression synthesis for facial animation. In this work, we propose a manifold-based 3D face reconstruction approach to estimating the 3D face model and the associated expression deformation from a single face image. With the proposed robust weighted feature map (RWF), we can obtain the dense correspondences between 3D face models and build a nonlinear 3D expression manifold from a large set of 3D facial expression models. Then a Gaussian mixture model in this manifold is learned to represent the distribution of expression deformation. By combining the merits of morphable neutral face model and the low-dimensional expression manifold, a novel algorithm is developed to reconstruct the 3D face geometry as well as the facial deformation from a single face image in an energy minimization framework. Experimental results on simulated and real images are shown to validate the effectiveness and accuracy of the proposed algorithm.

Aerodynamic effects of corrugation and deformation in flapping wings of hovering hoverflies.

PubMed

Du, Gang; Sun, Mao

2012-05-07

We investigated the aerodynamic effects of wing deformation and corrugation of a three-dimensional model hoverfly wing at a hovering condition by solving the Navier-Stokes equations on a dynamically deforming grid. Various corrugated wing models were tested. Insight into whether or not there existed significant aerodynamic coupling between wing deformation (camber and twist) and wing corrugation was obtained by comparing aerodynamic forces of four cases: a smooth-plate wing in flapping motion without deformation (i.e. a rigid flat-plate wing in flapping motion); a smooth-plate wing in flapping motion with deformation; a corrugated wing in flapping motion without deformation (i.e. a rigid corrugated wing in flapping motion); a corrugated wing in flapping motion with deformation. There was little aerodynamic coupling between wing deformation and corrugation: the aerodynamic effect of wing deformation and corrugation acting together was approximately a superposition of those of deformation and corrugation acting separately. When acting alone, the effect of wing deformation was to increase the lift by 9.7% and decrease the torque (or aerodynamic power) by 5.2%, and that of wing corrugation was to decrease the lift by 6.5% and increase the torque by 2.2%. But when acting together, the wing deformation and corrugation only increased the lift by ~3% and decreased the torque by ~3%. That is, the combined aerodynamic effect of deformation and corrugation is rather small. Thus, wing corrugation is mainly for structural, not aerodynamic, purpose, and in computing or measuring the aerodynamic forces, using a rigid flat-plate wing to model the corrugated deforming wing at hovering condition can be a good approximation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Details of insect wing design and deformation enhance aerodynamic function and flight efficiency.

PubMed

Young, John; Walker, Simon M; Bomphrey, Richard J; Taylor, Graham K; Thomas, Adrian L R

2009-09-18

Insect wings are complex structures that deform dramatically in flight. We analyzed the aerodynamic consequences of wing deformation in locusts using a three-dimensional computational fluid dynamics simulation based on detailed wing kinematics. We validated the simulation against smoke visualizations and digital particle image velocimetry on real locusts. We then used the validated model to explore the effects of wing topography and deformation, first by removing camber while keeping the same time-varying twist distribution, and second by removing camber and spanwise twist. The full-fidelity model achieved greater power economy than the uncambered model, which performed better than the untwisted model, showing that the details of insect wing topography and deformation are important aerodynamically. Such details are likely to be important in engineering applications of flapping flight.

Intraplate Crustal Deformation Within the Northern Sinai Microplate: Evidence from Paleomagnetic Directions and Mechanical Modeling

NASA Astrophysics Data System (ADS)

Dembo, N.; Granot, R.; Hamiel, Y.

2017-12-01

The intraplate crustal deformation found in the northern part of the Sinai Microplate, located near the northern Dead Sea Fault plate boundary, is examined. Previous studies have suggested that distributed deformation in Lebanon is accommodated by regional uniform counterclockwise rigid block rotations. However, remanent magnetization directions observed near the Lebanese restraining bend are not entirely homogeneous suggesting that an unexplained and complex internal deformation pattern exists. In order to explain the variations in the amount of vertical-axis rotations we construct a mechanical model of the major active faults in the region that simulates the rotational deformation induced by motion along these faults. The rotational pattern calculated by the mechanical modeling predicts heterogeneous distribution of rotations around the faults. The combined rotation field that considers both the fault induced rotations and the already suggested regional block rotations stands in general agreement with the observed magnetization directions. Overall, the modeling results provide a more detailed and complete picture of the deformation pattern in this region and show that rotations induced by motion along the Dead Sea Fault act in parallel to rigid block rotations. Finally, the new modeling results unravel important insights as to the fashion in which crustal deformation is distributed within the northern part of the Sinai Microplate and propose an improved deformational mechanism that might be appropriate for other plate margins as well.

Unexpected angular or rotational deformity after corrective osteotomy

PubMed Central

2014-01-01

Background Codman’s paradox reveals a misunderstanding of geometry in orthopedic practice. Physicians often encounter situations that cannot be understood intuitively during orthopedic interventions such as corrective osteotomy. Occasionally, unexpected angular or rotational deformity occurs during surgery. This study aimed to draw the attention of orthopedic surgeons toward the concepts of orientation and rotation and demonstrate the potential for unexpected deformity after orthopedic interventions. This study focused on three situations: shoulder arthrodesis, femoral varization derotational osteotomy, and femoral derotation osteotomy. Methods First, a shoulder model was generated to calculate unexpected rotational deformity to demonstrate Codman’s paradox. Second, femoral varization derotational osteotomy was simulated using a cylinder model. Third, a reconstructed femoral model was used to calculate unexpected angular or rotational deformity during femoral derotation osteotomy. Results Unexpected external rotation was found after forward elevation and abduction of the shoulder joint. In the varization and derotation model, closed-wedge osteotomy and additional derotation resulted in an unexpected extension and valgus deformity, namely, under-correction of coxa valga. After femoral derotational osteotomy, varization and extension of the distal fragment occurred, although the extension was negligible. Conclusions Surgeons should be aware of unexpected angular deformity after surgical procedure involving bony areas. The degree of deformity differs depending on the context of the surgical procedure. However, this study reveals that notable deformities can be expected during orthopedic procedures such as femoral varization derotational osteotomy. PMID:24886469

Structural history of Maxwell Montes, Venus: Implications for Venusian mountain belt formation

NASA Astrophysics Data System (ADS)

Keep, Myra; Hansen, Vicki L.

1994-12-01

Models for Venusian mountain belt formation are important for understanding planetary geodynamic mechanisms. A range of data sets at various scales must be considered in geodynamic modelling. Long wavelength data, such as gravity and geoid to topography ratios, need constraints from smaller-scale observations of the surface. Pre-Magellan images of the Venusian surface were not of high enough resolution to observe details of surface deformation. High-resolution Magellan images of Maxwell Montes and the other deformation belts allow us to determine the nature of surfce deformation. With these images we can begin to understand the constraints that surface deformation places on planetary dynamic models. Maxwell Montes and three other deformation belts (Akna, Freyja, and Danu montes) surround the highland plateau Lakshmi Planum in Venus, northern hemisphere. Maxwell, the highest of these belts, stands 11 km above mean planetary radius. We present a detailed structural and kinematic study of Maxwell Montes. Key observations include (1) dominant structural fabrics are broadly distributed and show little change in spacing relative to elevation changes of several kilometers; (2) the spacing, wavelength, and inferred amplitude of mapped structures are small, (3) interpreted extensional structures occur only in areas of steep slope, with no extension at the highest topographic levels; and (4) deformation terminates abruptly at the base of steep slopes. One implication of these observations is that topography is independent of thin-skinned, broadly distributed, Maxwell deformation. Maxwell is apparently stable, with no observed extensional collapse. We propose a ``deformation-from-below'' model for Maxwell, in which the crust deforms passively over structurally imbricated and thickened lower crust. This model may have implications for the other deformation belts.

Structural history of Maxwell Montes, Venus: Implications for Venusian mountain belt formation

NASA Astrophysics Data System (ADS)

Keep, Myra; Hansen, Vicki L.

1994-12-01

Models for Venusian mountain belt formation are important for understanding planetary geodynamic mechanisms. A range of data sets at various scales must be considered in geodynamic modelling. Long wavelength data, such as gravity and geoid to topography ratios, need constraints from smaller-scale observations of the surface. Pre-Magellan images of the Venusian surface were not of high enough resolution to observe details of surface deformation. High-resolution Magellan images of Maxwell Montes and the other deformation belts allow us to determine the nature of surface deformation. With these images we can begin to understand the constraints that surface deformation places on planetary dynamic models. Maxwell Montes and three other deformation belts (Akna, Freyja, and Danu montes) surround the highland plateau Lakshmi Planum in Venus' northern hemisphere. Maxwell, the highest of these belts, stands 11 km above mean planetary radius. We present a detailed structural and kinematic study of Maxwell Montes. Key observations include (1) dominant structure fabrics are broadly distributed and show little change in spacing relative to elevation changes of several kilometers; (2) the spacing, wavelength and inferred amplitude of mapped structures are small; (3) interpreted extensional structures occur only in areas of steep slope, with no extension at the highest topographic levels; and (4) deformation terminates abruptly at the base of steep slopes. One implications of these observations is that topography is independent of thin-skinned, broadly distributed, Maxwell deformation. Maxwell is apparently stable, with no observed extensional collapse. We propose a 'deformation-from-below' model for Maxwell, in which the crust deforms passively over structurally imbricated and thickened lower crust. This model may have implications for the other deformation belts.

Atypical transitions in material response during constant strain rate, hot deformation of austenitic steel

NASA Astrophysics Data System (ADS)

Borah, Utpal; Aashranth, B.; Samantaray, Dipti; Kumar, Santosh; Davinci, M. Arvinth; Albert, Shaju K.; Bhaduri, A. K.

2017-10-01

Work hardening, dynamic recovery and dynamic recrystallization (DRX) occurring during hot working of austenitic steel have been extensively studied. Various empirical models describe the nature and effects of these phenomena in a typical framework. However, the typical model is sometimes violated following atypical transitions in deformation mechanisms of the material. To ascertain the nature of these atypical transitions, researchers have intentionally introduced discontinuities in the deformation process, such as interrupting the deformation as in multi-step rolling and abruptly changing the rate of deformation. In this work, we demonstrate that atypical transitions are possible even in conventional single-step, constant strain rate deformation of austenitic steel. Towards this aim, isothermal, constant true strain rate deformation of austenitic steel has been carried out in a temperature range of 1173-1473 K and strain rate range of 0.01-100 s-1. The microstructural response corresponding to each deformation condition is thoroughly investigated. The conventional power-law variation of deformation grain size (D) with peak stress (σp) during DRX is taken as a typical model and experimental data is tested against it. It is shown that σp-D relations exhibit an atypical two-slope linear behaviour rather than a continuous power law relation. Similarly, the reduction in σp with temperature (T) is found to consist of two discrete linear segments. In practical terms, the two linear segments denote two distinct microstructural responses to deformation. As a consequence of this distinction, the typical model breaks down and is unable to completely relate microstructural evolution to flow behaviour. The present work highlights the microstructural mechanisms responsible for this atypical behavior and suggests strategies to incorporate the two-slope behaviour in the DRX model.

Material Properties from Air Puff Corneal Deformation by Numerical Simulations on Model Corneas.

PubMed

Bekesi, Nandor; Dorronsoro, Carlos; de la Hoz, Andrés; Marcos, Susana

2016-01-01

To validate a new method for reconstructing corneal biomechanical properties from air puff corneal deformation images using hydrogel polymer model corneas and porcine corneas. Air puff deformation imaging was performed on model eyes with artificial corneas made out of three different hydrogel materials with three different thicknesses and on porcine eyes, at constant intraocular pressure of 15 mmHg. The cornea air puff deformation was modeled using finite elements, and hyperelastic material parameters were determined through inverse modeling, minimizing the difference between the simulated and the measured central deformation amplitude and central-peripheral deformation ratio parameters. Uniaxial tensile tests were performed on the model cornea materials as well as on corneal strips, and the results were compared to stress-strain simulations assuming the reconstructed material parameters. The measured and simulated spatial and temporal profiles of the air puff deformation tests were in good agreement (< 7% average discrepancy). The simulated stress-strain curves of the studied hydrogel corneal materials fitted well the experimental stress-strain curves from uniaxial extensiometry, particularly in the 0-0.4 range. Equivalent Young´s moduli of the reconstructed material properties from air-puff were 0.31, 0.58 and 0.48 MPa for the three polymer materials respectively which differed < 1% from those obtained from extensiometry. The simulations of the same material but different thickness resulted in similar reconstructed material properties. The air-puff reconstructed average equivalent Young´s modulus of the porcine corneas was 1.3 MPa, within 18% of that obtained from extensiometry. Air puff corneal deformation imaging with inverse finite element modeling can retrieve material properties of model hydrogel polymer corneas and real corneas, which are in good correspondence with those obtained from uniaxial extensiometry, suggesting that this is a promising technique to retrieve quantitative corneal biomechanical properties.

Accidental degeneracies in nonlinear quantum deformed systems

NASA Astrophysics Data System (ADS)

Aleixo, A. N. F.; Balantekin, A. B.

2011-09-01

We construct a multi-parameter nonlinear deformed algebra for quantum confined systems that includes many other deformed models as particular cases. We demonstrate that such systems exhibit the property of accidental pairwise energy level degeneracies. We also study, as a special case of our multi-parameter deformation formalism, the extension of the Tamm-Dancoff cutoff deformed oscillator and the occurrence of accidental pairwise degeneracy in the energy levels of the deformed system. As an application, we discuss the case of a trigonometric Rosen-Morse potential, which is successfully used in models for quantum confined systems, ranging from electrons in quantum dots to quarks in hadrons.

Deformed Palmprint Matching Based on Stable Regions.

PubMed

Wu, Xiangqian; Zhao, Qiushi

2015-12-01

Palmprint recognition (PR) is an effective technology for personal recognition. A main problem, which deteriorates the performance of PR, is the deformations of palmprint images. This problem becomes more severe on contactless occasions, in which images are acquired without any guiding mechanisms, and hence critically limits the applications of PR. To solve the deformation problems, in this paper, a model for non-linearly deformed palmprint matching is derived by approximating non-linear deformed palmprint images with piecewise-linear deformed stable regions. Based on this model, a novel approach for deformed palmprint matching, named key point-based block growing (KPBG), is proposed. In KPBG, an iterative M-estimator sample consensus algorithm based on scale invariant feature transform features is devised to compute piecewise-linear transformations to approximate the non-linear deformations of palmprints, and then, the stable regions complying with the linear transformations are decided using a block growing algorithm. Palmprint feature extraction and matching are performed over these stable regions to compute matching scores for decision. Experiments on several public palmprint databases show that the proposed models and the KPBG approach can effectively solve the deformation problem in palmprint verification and outperform the state-of-the-art methods.

Process Modelling of Curing Process-Induced Internal Stress and Deformation of Composite Laminate Structure with Elastic and Viscoelastic Models

NASA Astrophysics Data System (ADS)

Li, Dongna; Li, Xudong; Dai, Jianfeng

2018-06-01

In this paper, two kinds of transient models, the viscoelastic model and the linear elastic model, are established to analyze the curing deformation of the thermosetting resin composites, and are calculated by COMSOL Multiphysics software. The two models consider the complicated coupling between physical and chemical changes during curing process of the composites and the time-variant characteristic of material performance parameters. Subsequently, the two proposed models are implemented respectively in a three-dimensional composite laminate structure, and a simple and convenient method of local coordinate system is used to calculate the development of residual stresses, curing shrinkage and curing deformation for the composite laminate. Researches show that the temperature, degree of curing (DOC) and residual stresses during curing process are consistent with the study in literature, so the curing shrinkage and curing deformation obtained on these basis have a certain referential value. Compared the differences between the two numerical results, it indicates that the residual stress and deformation calculated by the viscoelastic model are more close to the reference value than the linear elastic model.

Brain shift computation using a fully nonlinear biomechanical model.

PubMed

Wittek, Adam; Kikinis, Ron; Warfield, Simon K; Miller, Karol

2005-01-01

In the present study, fully nonlinear (i.e. accounting for both geometric and material nonlinearities) patient specific finite element brain model was applied to predict deformation field within the brain during the craniotomy-induced brain shift. Deformation of brain surface was used as displacement boundary conditions. Application of the computed deformation field to align (i.e. register) the preoperative images with the intraoperative ones indicated that the model very accurately predicts the displacements of gravity centers of the lateral ventricles and tumor even for very limited information about the brain surface deformation. These results are sufficient to suggest that nonlinear biomechanical models can be regarded as one possible way of complementing medical image processing techniques when conducting nonrigid registration. Important advantage of such models over the linear ones is that they do not require unrealistic assumptions that brain deformations are infinitesimally small and brain tissue stress-strain relationship is linear.

Deformable complex network for refining low-resolution X-ray structures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Chong; Wang, Qinghua; Ma, Jianpeng, E-mail: jpma@bcm.edu

2015-10-27

A new refinement algorithm called the deformable complex network that combines a novel angular network-based restraint with a deformable elastic network model in the target function has been developed to aid in structural refinement in macromolecular X-ray crystallography. In macromolecular X-ray crystallography, building more accurate atomic models based on lower resolution experimental diffraction data remains a great challenge. Previous studies have used a deformable elastic network (DEN) model to aid in low-resolution structural refinement. In this study, the development of a new refinement algorithm called the deformable complex network (DCN) is reported that combines a novel angular network-based restraint withmore » the DEN model in the target function. Testing of DCN on a wide range of low-resolution structures demonstrated that it constantly leads to significantly improved structural models as judged by multiple refinement criteria, thus representing a new effective refinement tool for low-resolution structural determination.« less

Modelling of the plastic deformation and primary creep of metals coupled with DC in terms of the synthetic theory of irrecoverable deformation

NASA Astrophysics Data System (ADS)

Rusinko, Andrew; Varga, Peter

2018-04-01

The paper deals with modelling of the plastic and creep deformation of metals coupled with current. The passage of DC manifests itself in the increase in creep deformation and leads to primary creep time shortening. With plastic deformation, a short electric impulse results in the step-wise decrease of stress (stress-drop) on the stress-strain diagram. To catch these phenomena, we utilize the synthetic theory of recoverable deformation. The constitutive equation of this theory is supplemented by a term taking into account the intensity of DC. Further, we introduce DC intensity into the function governing transient creep. As a result, we predict the parameters of transient creep and calculate the stress-drop as a function of current intensity. The model results show good agreement with experimental data.

Investigation of Deformation Dynamics in a Wrought Magnesium Alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Wei; Qiao, Hua; An, Ke

2014-11-01

In the present research, the deformation dynamics and the effect of the deformation history on plastic deformation in a wrought magnesium alloy have been studied using real-time in-situ neutron diffraction measurements under a continuous loading condition and elastic-viscoplastic self-consistent (EVPSC) polycrystal modeling. The experimental results reveal that the pre-deformation delayed the activation of the tensile twinning during subsequent compression, mainly resulting from the residual strain. No apparent detwinning occurred during unloading and even in the elastic region during reverse loading. It is believed that the grain rotation played an important role in the elastic region during reverse loading. The EVPSCmore » model, which has been recently updated by implementing the twinning and detwinning model, was employed to characterize the deformation mechanism during the strain-path changes. The simulation result predicts well the experimental observation from the real-time in-situ neutron diffraction measurements. The present study provides a deep insight of the nature of deformation mechanisms in a hexagonal close-packed structured polycrystalline wrought magnesium alloy, which might lead to a new era of deformation-mechanism research.« less

Modeling of spray droplets deformation and breakup

NASA Technical Reports Server (NTRS)

Ibrahim, E. A.; Yang, H. Q.; Przekwas, A. J.

1993-01-01

A droplet deformation and breakup (DDB) model is proposed to study shear-type mechanism of spray droplets in pure extentional flows. A numerical solution of the DDB model equation is obtained using a fourth-order Runge-Kutta initial-value solver. The predictions of the DDB model as well as semianalytical and the Taylor analogy models are compared with the experimental data (Krzeczkowski, 1980) for shear breakup, which depict the dimensionless deformation of the drop vs dimensionless time.

Lithotripter shock wave interaction with a bubble near various biomaterials.

PubMed

Ohl, S W; Klaseboer, E; Szeri, A J; Khoo, B C

2016-10-07

Following previous work on the dynamics of an oscillating bubble near a bio-material (Ohl et al 2009 Phys. Med. Biol. 54 6313-36) and the interaction of a bubble with a shockwave (Klaseboer et al 2007 J. Fluid Mech. 593 33-56), the present work concerns the interaction of a gas bubble with a traveling shock wave (such as from a lithotripter) in the vicinity of bio-materials such as fat, skin, muscle, cornea, cartilage, and bone. The bubble is situated in water (to represent a water-like biofluid). The bubble collapses are not spherically symmetric, but tend to feature a high speed jet. A few simulations are performed and compared with available experimental observations from Sankin and Zhong (2006 Phys. Rev. E 74 046304). The collapses of cavitation bubbles (created by laser in the experiment) near an elastic membrane when hit by a lithotripter shock wave are correctly captured by the simulation. This is followed by a more systematic study of the effects involved concerning shockwave bubble biomaterial interactions. If a subsequent rarefaction wave hits the collapsed bubble, it will re-expand to a very large size straining the bio-materials nearby before collapsing once again. It is noted that, for hard bio-material like bone, reflection of the shock wave at the bone-water interface can affect the bubble dynamics. Also the initial size of the bubble has a significant effect. Large bubbles (∼1 mm) will split into smaller bubbles, while small bubbles collapse with a high speed jet in the travel direction of the shock wave. The numerical model offers a computationally efficient way of understanding the complex phenomena involving the interplay of a bubble, a shock wave, and a nearby bio-material.

Shockwave lithotripsy with music: Less painful and more satisfactory treatment.

PubMed

Ordaz Jurado, D G; Budia Alba, A; Bahilo Mateu, P; Trassierra Villa, M; López-Acón, D; Boronat Tormo, F

2017-11-01

The objective of this study was to determine whether listening to music during a session of extracorporeal shockwave lithotripsy (ESWL) improves patients' pain. A simple, blind randomisation was undertaken of patients with kidney and ureter stones attending an ESWL session of 7,000 waves for the first time, between September and December 2014. One group was given music and the other was not. The age, gender, location of stones (kidney/ureter) were recorded and 2questionnaires: pre ESWL (questionnaire A) and postESWL (questionnaire B). Each questionnaire contained a question about anxiety and another question on pain on the Likert scale (0-10). Questionnaire B also had a question on satisfaction and comfort (Likert 0-10). Other variables included heart rate, respiratory rate, systolic and diastolic blood pressure on wave 2,000, 5,000 and 7,000, reason for halting the procedure, total pethidine (mg), secondary analgesia, energy (J) and frequency (Hz). Bivariate analysis using the Student's t-test, X 2 /Fisher test and a multiple linear regression model. The sample comprised 95 patients, with a mean age of 52 (±13) years, 35 (36.84%) females, 60 (63.2%) males. A total of 25 (26.3%) ureter stones and 70 (73.7%) kidney stones. A number of 42 (44.2%) patients were given music. There were no differences between the demographic variables or questionnaire A scores. Satisfaction and pain were better on questionnaire B with music. Music can reduce pain and improve patient satisfaction in ESWL treatment. More studies are required to confirm this effect. Copyright © 2017 AEU. Publicado por Elsevier España, S.L.U. All rights reserved.

Lithotripter shock wave interaction with a bubble near various biomaterials

NASA Astrophysics Data System (ADS)

Ohl, S. W.; Klaseboer, E.; Szeri, A. J.; Khoo, B. C.

2016-10-01

Following previous work on the dynamics of an oscillating bubble near a bio-material (Ohl et al 2009 Phys. Med. Biol. 54 6313-36) and the interaction of a bubble with a shockwave (Klaseboer et al 2007 J. Fluid Mech. 593 33-56), the present work concerns the interaction of a gas bubble with a traveling shock wave (such as from a lithotripter) in the vicinity of bio-materials such as fat, skin, muscle, cornea, cartilage, and bone. The bubble is situated in water (to represent a water-like biofluid). The bubble collapses are not spherically symmetric, but tend to feature a high speed jet. A few simulations are performed and compared with available experimental observations from Sankin and Zhong (2006 Phys. Rev. E 74 046304). The collapses of cavitation bubbles (created by laser in the experiment) near an elastic membrane when hit by a lithotripter shock wave are correctly captured by the simulation. This is followed by a more systematic study of the effects involved concerning shockwave bubble biomaterial interactions. If a subsequent rarefaction wave hits the collapsed bubble, it will re-expand to a very large size straining the bio-materials nearby before collapsing once again. It is noted that, for hard bio-material like bone, reflection of the shock wave at the bone—water interface can affect the bubble dynamics. Also the initial size of the bubble has a significant effect. Large bubbles (˜1 mm) will split into smaller bubbles, while small bubbles collapse with a high speed jet in the travel direction of the shock wave. The numerical model offers a computationally efficient way of understanding the complex phenomena involving the interplay of a bubble, a shock wave, and a nearby bio-material.

Changes of articular cartilage and subchondral bone after extracorporeal shockwave therapy in osteoarthritis of the knee

PubMed Central

Wang, Ching-Jen; Cheng, Jai-Hong; Chou, Wen-Yi; Hsu, Shan-Ling; Chen, Jen-Hung; Huang, Chien-Yiu

2017-01-01

We assessed the pathological changes of articular cartilage and subchondral bone on different locations of the knee after extracorporeal shockwave therapy (ESWT) in early osteoarthritis (OA). Rat knees under OA model by anterior cruciate ligament transaction (ACLT) and medial meniscectomy (MM) to induce OA changes. Among ESWT groups, ESWT were applied to medial (M) femur (F) and tibia (T) condyles was better than medial tibia condyle, medial femur condyle as well as medial and lateral (L) tibia condyles in gross osteoarthritic areas (p<0.05), osteophyte formation and subchondral sclerotic bone (p<0.05). Using sectional cartilage area, modified Mankin scoring system as well as thickness of calcified and un-calcified cartilage analysis, the results showed that articular cartilage damage was ameliorated and T+F(M) group had the most protection as compared with other locations (p<0.05). Detectable cartilage surface damage and proteoglycan loss were measured and T+F(M) group showed the smallest lesion score among other groups (p<0.05). Micro-CT revealed significantly improved in subchondral bone repair in all ESWT groups compared to OA group (p<0.05). There were no significantly differences in bone remodeling after ESWT groups except F(M) group. In the immunohistochemical analysis, T+F(M) group significant reduced TUNEL activity, promoted cartilage proliferation by observation of PCNA marker and reduced vascular invasion through observation of CD31 marker for angiogenesis compared to OA group (P<0.001). Overall the data suggested that the order of the effective site of ESWT was T+F(M) ≧ T(M) > T(M+L) > F(M) in OA rat knees. PMID:28367081

Changes of articular cartilage and subchondral bone after extracorporeal shockwave therapy in osteoarthritis of the knee.

PubMed

Wang, Ching-Jen; Cheng, Jai-Hong; Chou, Wen-Yi; Hsu, Shan-Ling; Chen, Jen-Hung; Huang, Chien-Yiu

2017-01-01

We assessed the pathological changes of articular cartilage and subchondral bone on different locations of the knee after extracorporeal shockwave therapy (ESWT) in early osteoarthritis (OA). Rat knees under OA model by anterior cruciate ligament transaction (ACLT) and medial meniscectomy (MM) to induce OA changes. Among ESWT groups, ESWT were applied to medial (M) femur (F) and tibia (T) condyles was better than medial tibia condyle, medial femur condyle as well as medial and lateral (L) tibia condyles in gross osteoarthritic areas (p<0.05), osteophyte formation and subchondral sclerotic bone (p<0.05). Using sectional cartilage area, modified Mankin scoring system as well as thickness of calcified and un-calcified cartilage analysis, the results showed that articular cartilage damage was ameliorated and T+F(M) group had the most protection as compared with other locations (p<0.05). Detectable cartilage surface damage and proteoglycan loss were measured and T+F(M) group showed the smallest lesion score among other groups (p<0.05). Micro-CT revealed significantly improved in subchondral bone repair in all ESWT groups compared to OA group (p<0.05). There were no significantly differences in bone remodeling after ESWT groups except F(M) group. In the immunohistochemical analysis, T+F(M) group significant reduced TUNEL activity, promoted cartilage proliferation by observation of PCNA marker and reduced vascular invasion through observation of CD31 marker for angiogenesis compared to OA group (P<0.001). Overall the data suggested that the order of the effective site of ESWT was T+F(M) ≧ T(M) > T(M+L) > F(M) in OA rat knees.

Correcting for deformation in skin-based marker systems.

PubMed

Alexander, E J; Andriacchi, T P

2001-03-01

A new technique is described that reduces error due to skin movement artifact in the opto-electronic measurement of in vivo skeletal motion. This work builds on a previously described point cluster technique marker set and estimation algorithm by extending the transformation equations to the general deformation case using a set of activity-dependent deformation models. Skin deformation during activities of daily living are modeled as consisting of a functional form defined over the observation interval (the deformation model) plus additive noise (modeling error). The method is described as an interval deformation technique. The method was tested using simulation trials with systematic and random components of deformation error introduced into marker position vectors. The technique was found to substantially outperform methods that require rigid-body assumptions. The method was tested in vivo on a patient fitted with an external fixation device (Ilizarov). Simultaneous measurements from markers placed on the Ilizarov device (fixed to bone) were compared to measurements derived from skin-based markers. The interval deformation technique reduced the errors in limb segment pose estimate by 33 and 25% compared to the classic rigid-body technique for position and orientation, respectively. This newly developed method has demonstrated that by accounting for the changing shape of the limb segment, a substantial improvement in the estimates of in vivo skeletal movement can be achieved.

Analysis of Mining Terrain Deformation Characteristics with Deformation Information System

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Milczarek, Wojciech; Grzempowski, Piotr

2014-05-01

Mapping and prediction of mining related deformations of the earth surface is an important measure for minimising threat to surface infrastructure, human population, the environment and safety of the mining operation itself arising from underground extraction of useful minerals. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and increasing with the development of geographical information technologies. These include for example: terrestrial geodetic measurements, global positioning systems, remote sensing, spatial interpolation, finite element method modelling, GIS based modelling, geological modelling, empirical modelling using the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The aim of this paper is to introduce the concept of an integrated Deformation Information System (DIS) developed in geographic information systems environment for analysis and modelling of various spatial data related to mining activity and demonstrate its applications for mapping and visualising, as well as identifying possible mining terrain deformation areas with various spatial modelling methods. The DIS concept is based on connected modules that include: the spatial database - the core of the system, the spatial data collection module formed by: terrestrial, satellite and remote sensing measurements of the ground changes, the spatial data mining module for data discovery and extraction, the geological modelling module, the spatial data modeling module with data processing algorithms for spatio-temporal analysis and mapping of mining deformations and their characteristics (e.g. deformation parameters: tilt, curvature and horizontal strain), the multivariate spatial data classification module and the visualization module allowing two-dimensional interactive and static mapping and three-dimensional visualizations of mining ground characteristics. The Systems's functionality has been presented on the case study of a coal mining region in SW Poland where it has been applied to study characteristics and map mining induced ground deformations in a city in the last two decades of underground coal extraction and in the first decade after the end of mining. The mining subsidence area and its deformation parameters (tilt and curvature) have been calculated and the latter classified and mapped according to the Polish regulations. In addition possible areas of ground deformation have been indicated based on multivariate spatial data analysis of geological and mining operation characteristics with the geographically weighted regression method.

Prediction of water loss and viscoelastic deformation of apple tissue using a multiscale model.

PubMed

Aregawi, Wondwosen A; Abera, Metadel K; Fanta, Solomon W; Verboven, Pieter; Nicolai, Bart

2014-11-19

A two-dimensional multiscale water transport and mechanical model was developed to predict the water loss and deformation of apple tissue (Malus × domestica Borkh. cv. 'Jonagold') during dehydration. At the macroscopic level, a continuum approach was used to construct a coupled water transport and mechanical model. Water transport in the tissue was simulated using a phenomenological approach using Fick's second law of diffusion. Mechanical deformation due to shrinkage was based on a structural mechanics model consisting of two parts: Yeoh strain energy functions to account for non-linearity and Maxwell's rheological model of visco-elasticity. Apparent parameters of the macroscale model were computed from a microscale model. The latter accounted for water exchange between different microscopic structures of the tissue (intercellular space, the cell wall network and cytoplasm) using transport laws with the water potential as the driving force for water exchange between different compartments of tissue. The microscale deformation mechanics were computed using a model where the cells were represented as a closed thin walled structure. The predicted apparent water transport properties of apple cortex tissue from the microscale model showed good agreement with the experimentally measured values. Deviations between calculated and measured mechanical properties of apple tissue were observed at strains larger than 3%, and were attributed to differences in water transport behavior between the experimental compression tests and the simulated dehydration-deformation behavior. Tissue dehydration and deformation in the high relative humidity range ( > 97% RH) could, however, be accurately predicted by the multiscale model. The multiscale model helped to understand the dynamics of the dehydration process and the importance of the different microstructural compartments (intercellular space, cell wall, membrane and cytoplasm) for water transport and mechanical deformation.

Study of optical techniques for the Ames unitary wind tunnels. Part 4: Model deformation

NASA Technical Reports Server (NTRS)

Lee, George

1992-01-01

A survey of systems capable of model deformation measurements was conducted. The survey included stereo-cameras, scanners, and digitizers. Moire, holographic, and heterodyne interferometry techniques were also looked at. Stereo-cameras with passive or active targets are currently being deployed for model deformation measurements at NASA Ames and LaRC, Boeing, and ONERA. Scanners and digitizers are widely used in robotics, motion analysis, medicine, etc., and some of the scanner and digitizers can meet the model deformation requirements. Commercial stereo-cameras, scanners, and digitizers are being improved in accuracy, reliability, and ease of operation. A number of new systems are coming onto the market.

Paleohydrologic controls on soft-sediment deformation in the Navajo Sandstone

NASA Astrophysics Data System (ADS)

Bryant, Gerald; Cushman, Robert; Nick, Kevin; Miall, Andrew

2016-10-01

Many workers have noted the presence of contorted cross-strata in the Navajo Sandstone and other ancient eolianites, and have recognized their significance as indicators of sediment saturation during the accumulation history. Horowitz (1982) proposed a general model for the production of such features in ancient ergs by episodic, seismically induced liquefaction of accumulated sand. A key feature of that popular model is the prevalence of a flat water table, characteristic of a hyper-arid climatic regime, during deformation. Under arid climatic conditions, the water table is established by regional flow and liquefaction is limited to the saturated regions below the level of interdune troughs. However, various paleohydrological indicators from Navajo Sandstone outcrops point toward a broader range of water table configurations during the deformation history of that eolianite. Some outcrops reveal extensive deformation complexes that do not appear to have extended to the contemporary depositional surface. These km-scale zones of deformation, affecting multiple sets of cross-strata, and grading upward into undeformed crossbeds may represent deep water table conditions, coupled with high intensity triggers, which produced exclusively intrastratal deformation. Such occurrences contrast with smaller-scale complexes formed within the zone of interaction between the products of soft-sediment deformation and surface processes of deposition and erosion. The Horowitz model targets the smaller-scale deformation morphologies produced in this near-surface environment. This study examines the implications of a wet climatic regime for the Horowitz deformation model. It demonstrates how a contoured water table, characteristic of humid climates, may have facilitated deformation within active bedforms, as well as in the accumulation. Intra-dune deformation would enable deflation of deformation features during the normal course of dune migration, more parsimoniously accounting for: the frequent occurrence of erosionally truncated deformation structures in the Navajo Sandstone; the production of such erosional truncations during bedform climb and aggradation of the accumulation; and the dramatic fluctuations in the water table required to deposit dry eolian sand, deform those deposits under saturated conditions, and then dry the deformed sand to enable deflation.

The effects of non-Newtonian viscosity on the deformation of red blood cells in a shear flow

NASA Astrophysics Data System (ADS)

Sesay, Juldeh

2005-11-01

The analyses of the effects of non-Newtonian viscosity on the membrane of red blood cells (RBCs) suspended in a shear flow are presented. The specific objective is to investigate the mechanical deformation on the surfaces of an ellipsoidal particle model. The hydrodynamic stresses and other forces on the surface of the particle are used to determine the cell deformation. We extended previous works, which were based on the Newtonian fluid models, to the non-Newtonian case, and focus on imposed shear rate values between 1 and 100 per second. Two viscosity models are investigated, which respectively correspond to a normal person and a patient with cerebrovascular accident (CVA). The results are compared with those obtained assuming a Newtonian model. We observed that the orientation of the cell influences the deformation and the imposed shear rate drives the local shear rate distribution along the particle surface. The integral particle deformation for the non-Newtonian models in the given shear rate regime is higher than that for the Newtonian reference model. Finally, the deformation of the cell surface decreases as the dissipation ratio increases.

A transverse isotropic constitutive model for the aortic valve tissue incorporating rate-dependency and fibre dispersion: Application to biaxial deformation.

PubMed

Anssari-Benam, Afshin; Tseng, Yuan-Tsan; Bucchi, Andrea

2018-05-26

This paper presents a continuum-based transverse isotropic model incorporating rate-dependency and fibre dispersion, applied to the planar biaxial deformation of aortic valve (AV) specimens under various stretch rates. The rate dependency of the mechanical behaviour of the AV tissue under biaxial deformation, the (pseudo-) invariants of the right Cauchy-Green deformation-rate tensor Ċ associated with fibre dispersion, and a new fibre orientation density function motivated by fibre kinematics are presented for the first time. It is shown that the model captures the experimentally observed deformation of the specimens, and characterises a shear-thinning behaviour associated with the dissipative (viscous) kinematics of the matrix and the fibres. The application of the model for predicting the deformation behaviour of the AV under physiological rates is illustrated and an example of the predicted σ-λ curves is presented. While the development of the model was principally motivated by the AV biomechanics requisites, the comprehensive theoretical approach employed in the study renders the model suitable for application to other fibrous soft tissues that possess similar rate-dependent and structural attributes. Crown Copyright © 2018. Published by Elsevier Ltd. All rights reserved.

Creep model of unsaturated sliding zone soils and long-term deformation analysis of landslides

NASA Astrophysics Data System (ADS)

Zou, Liangchao; Wang, Shimei; Zhang, Yeming

2015-04-01

Sliding zone soil is a special soil layer formed in the development of a landslide. Its creep behavior plays a significant role in long-term deformation of landslides. Due to rainfall infiltration and reservoir water level fluctuation, the soils in the slide zone are often in unsaturated state. Therefore, the investigation of creep behaviors of the unsaturated sliding zone soils is of great importance for understanding the mechanism of the long-term deformation of a landslide in reservoir areas. In this study, the full-process creep curves of the unsaturated soils in the sliding zone in different net confining pressure, matric suctions and stress levels were obtained from a large number of laboratory triaxial creep tests. A nonlinear creep model for unsaturated soils and its three-dimensional form was then deduced based on the component model theory and unsaturated soil mechanics. This creep model was validated with laboratory creep data. The results show that this creep model can effectively and accurately describe the nonlinear creep behaviors of the unsaturated sliding zone soils. In order to apply this creep model to predict the long-term deformation process of landslides, a numerical model for simulating the coupled seepage and creep deformation of unsaturated sliding zone soils was developed based on this creep model through the finite element method (FEM). By using this numerical model, we simulated the deformation process of the Shuping landslide located in the Three Gorges reservoir area, under the cycling reservoir water level fluctuation during one year. The simulation results of creep displacement were then compared with the field deformation monitoring data, showing a good agreement in trend. The results show that the creeping deformations of landslides have strong connections with the changes of reservoir water level. The creep model of unsaturated sliding zone soils and the findings obtained by numerical simulations in this study are conducive to reveal the mechanisms of the dynamic process of landslide deformation, and serve as an important basis for the prediction and evaluation of landslides.

An extended car-following model to describe connected traffic dynamics under cyberattacks

NASA Astrophysics Data System (ADS)

Wang, Pengcheng; Yu, Guizhen; Wu, Xinkai; Qin, Hongmao; Wang, Yunpeng

2018-04-01

In this paper, the impacts of the potential cyberattacks on vehicles are modeled through an extended car-following model. To better understand the mechanism of traffic disturbance under cyberattacks, the linear and nonlinear stability analysis are conducted respectively. Particularly, linear stability analysis is performed to obtain different neutral stability conditions with various parameters; and nonlinear stability analysis is carried out by using reductive perturbation method to derive the soliton solution of the modified Korteweg de Vries equation (mKdV) near the critical point, which is used to draw coexisting stability lines. Furthermore, by applying linear and nonlinear stability analysis, traffic flow state can be divided into three states, i.e., stable, metastable and unstable states which are useful to describe shockwave dynamics and driving behaviors under cyberattacks. The theoretical results show that the proposed car-following model is capable of successfully describing the car-following behavior of connected vehicles with cyberattacks. Finally, numerical simulation using real values has confirmed the validity of theoretical analysis. The results further demonstrate our model can be used to help avoid collisions and relieve traffic congestion with cybersecurity threats.

Modeling of plasticity and fracture of metals at shock loading

NASA Astrophysics Data System (ADS)

Mayer, A. E.; Khishchenko, K. V.; Levashov, P. R.; Mayer, P. N.

2013-05-01

In this paper, we present a model of dislocation plasticity and fracture of metals, which in combination with the wide-range equation of state and the continuum mechanics equations is a necessary component for simulation of the shock-wave loading. We take into account immobilization of dislocations and nucleation of micro-voids in weakened zones of substance; this is distinguished feature of the present version of the model. Accounting of the dislocations immobilization provides a better description of the unloading wave structure, while the detailed consideration of processes in the weakened zones expands the domain of applicability of fracture model to higher strain rates. We compare our results with the experimental data for the shock loading of aluminum, copper, and nickel samples; the comparison indicates satisfactory description of the elastic precursor, unloading wave, and spall pulse. Using the model, we investigate intently the early stage of the shock formation in solids; it is found out that the elastic precursor is formed even for a strong shock wave, and initially the precursor has very large amplitude and propagation velocity.

Image-Based 3D Face Modeling System

NASA Astrophysics Data System (ADS)

Park, In Kyu; Zhang, Hui; Vezhnevets, Vladimir

2005-12-01

This paper describes an automatic system for 3D face modeling using frontal and profile images taken by an ordinary digital camera. The system consists of four subsystems including frontal feature detection, profile feature detection, shape deformation, and texture generation modules. The frontal and profile feature detection modules automatically extract the facial parts such as the eye, nose, mouth, and ear. The shape deformation module utilizes the detected features to deform the generic head mesh model such that the deformed model coincides with the detected features. A texture is created by combining the facial textures augmented from the input images and the synthesized texture and mapped onto the deformed generic head model. This paper provides a practical system for 3D face modeling, which is highly automated by aggregating, customizing, and optimizing a bunch of individual computer vision algorithms. The experimental results show a highly automated process of modeling, which is sufficiently robust to various imaging conditions. The whole model creation including all the optional manual corrections takes only 2[InlineEquation not available: see fulltext.]3 minutes.

Discrete-to-continuum modelling of weakly interacting incommensurate two-dimensional lattices.

PubMed

Español, Malena I; Golovaty, Dmitry; Wilber, J Patrick

2018-01-01

In this paper, we derive a continuum variational model for a two-dimensional deformable lattice of atoms interacting with a two-dimensional rigid lattice. The starting point is a discrete atomistic model for the two lattices which are assumed to have slightly different lattice parameters and, possibly, a small relative rotation. This is a prototypical example of a three-dimensional system consisting of a graphene sheet suspended over a substrate. We use a discrete-to-continuum procedure to obtain the continuum model which recovers both qualitatively and quantitatively the behaviour observed in the corresponding discrete model. The continuum model predicts that the deformable lattice develops a network of domain walls characterized by large shearing, stretching and bending deformation that accommodates the misalignment and/or mismatch between the deformable and rigid lattices. Two integer-valued parameters, which can be identified with the components of a Burgers vector, describe the mismatch between the lattices and determine the geometry and the details of the deformation associated with the domain walls.

Electrode cartridge for pulse welding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bonnen, John Joseph Francis; Golovashchenko, Sergey Fedorovich; Mamutov, Alexander

A cartridge assembly for a tool includes a cartridge body or casing that contains a conductor. A conductor is connected to a pulse generator or source of stored charge that is discharged to vaporize the conductor and create an electro-hydraulic or electro-magnetic shockwave that is used to impact or pulse weld two parts together.

An Implementation of Interactive Objects on the Web.

ERIC Educational Resources Information Center

Fritze, Paul

With the release of ShockWave, MacroMedia Director animations can now be incorporated directly into Web pages to provide high quality animation and interactivity, to support, for example, tutorial style questions and instantaneous feedback. This paper looks at the application of this technique in the translation of a traditional computer-based…

Numerical study of unsteady shockwave reflections using an upwind TVD scheme

NASA Technical Reports Server (NTRS)

Hsu, Andrew T.; Liou, Meng-Sing

1990-01-01

An unsteady TVD Navier-Stokes solver was developed and applied to the problem of shock reflection on a circular cylinder. The obtained numerical results were compared with the Schlieren photos from an experimental study. These results show that the present computer code has the ability of capturing moving shocks.

Training over the Intranet--A Shockwave Case Study.

ERIC Educational Resources Information Center

Snydar, Sean

This case study explains how the Boeing Company has used the World Wide Web to deliver flight and maintenance computer-based training (CBT) that was originally created on a Macintosh computer and converted to Windows format. The case study begins with a brief discussion of the advantages of using corporate and institutional internal networks…

Hydrodynamic pressure processing: Impact on the quality attributes of fresh and further-processed meat products

USDA-ARS?s Scientific Manuscript database

This book chapter reviews hydrodynamic pressure processing (HDP) as an innovative, postharvest technology for enhancing the quality attributes of fresh and further-processed meat products. A variety of meat products have been tested for their response to the high pressure shockwaves of HDP. The st...

The Earth's Core: How Does It Work? Perspectives in Science. Number 1.

ERIC Educational Resources Information Center

Carnegie Institution of Washington, Washington, DC.

Various research studies designed to enhance knowledge about the earth's core are discussed. Areas addressed include: (1) the discovery of the earth's core; (2) experimental approaches used in studying the earth's core (including shock-wave experiments and experiments at high static pressures), the search for the core's light elements, the…

Generation of shockwave and vortex structures at the outflow of a boiling water jet

NASA Astrophysics Data System (ADS)

Alekseev, M. V.; Lezhnin, S. I.; Pribaturin, N. A.; Sorokin, A. L.

2014-12-01

Results of numerical simulation for shock waves and generation of vortex structures during unsteady outflow of boiling liquid jet are presented. The features of evolution of shock waves and vortex structures formation during unsteady outflow of boiling water are compared with corresponding structures during unsteady gas outflow.

Modelling heat and mass transfer in bread baking with mechanical deformation

NASA Astrophysics Data System (ADS)

Nicolas, V.; Salagnac, P.; Glouannec, P.; Ploteau, J.-P.; Jury, V.; Boillereaux, L.

2012-11-01

In this paper, the thermo-hydric behaviour of bread during baking is studied. A numerical model has been developed with Comsol Multiphysics© software. The model takes into account the heat and mass transfers in the bread and the phenomenon of swelling. This model predicts the evolution of temperature, moisture, gas pressure and deformation in French "baguette" during baking. Local deformation is included in equations using solid phase conservation and, global deformation is calculated using a viscous mechanic model. Boundary conditions are specified with the sole temperature model and vapour pressure estimation of the oven during baking. The model results are compared with experimental data for a classic baking. Then, the model is analysed according to physical properties of bread and solicitations for a better understanding of the interactions between different mechanisms within the porous matrix.

Spherical shock-wave propagation in three-dimensional granular packings.

PubMed

Xue, Kun; Bai, Chun-Hua

2011-02-01

We investigate numerically the spherical shock-wave propagation in an open dense granular packing perturbed by the sudden expansion of a spherical intruder in the interior of the pack, focusing on the correlation between geometrical fabrics and propagating properties. The measurements of the temporal and spatial variations in a variety of propagating properties define a consistent serrated wave substructure with characteristic length on the orders of particle diameters. Further inspection of particle packing reveals a well-defined particle layering that persists several particle diameters away from the intruder, although its dominant effects are only within one to two diameters. This interface-induced layering not only exactly coincides with the serrated wave profile, but also highlights the competition between two energy transmission mechanisms involving distinct transport speeds. The alternating dominances between these two mechanisms contribute to the nonlinear wave propagation on the particle scale. Moreover, the proliferation of intricate three-dimensional contact force networks suggests the anisotropic stress transmission, which is found to also arise from the localized packing structure in the vicinity of the intruder.

Laser-induced shock-wave lithotripsy of canine urocystoliths and nephroliths

NASA Astrophysics Data System (ADS)

Woods, J. P.; Bartels, Kenneth E.; Stair, Ernest L.; Schafer, Steven A.; Nordquist, Robert E.

1997-05-01

Urolithiasis is a common disease affecting dogs which can sometimes be treated with dietary and medical protocols. In many cases, however, medical management cannot be employed because the dietary restrictions are contraindicated, effective medical dissolution protocols for the calculi (uroliths) do not exist, or obstruction by the calculi may result in deterioration of renal function during the time required for medical dissolution. At present, the management of medically untreatable calculi has been surgical removal which may result in temporary but dramatic decrease in renal function, irreversible loss of damaged nephrons, and significant risk, particularly for bilateral or recurrent nephroliths. An innovative technique for the removal of these uroliths would involve laser lithotripsy which transforms light energy into acoustical energy generating a shock wave sufficient to fragment stones (photoacoustic ablation). The laser is transmitted via quartz fibers which are small and flexible and can be used under direct vision through endoscopes resulting in effective fragmentation with little surrounding tissue damage. Lasers are becoming increasingly more utilized in veterinary medicine, in contrast to the limited availability of other non-invasive methods of treatment of nephroliths (i.e. extracorporeal shock-wave lithotripsy).

The Experimental Study of Dynamics of Scaled Gas-Filled Bubble Collapse in Liquid

NASA Astrophysics Data System (ADS)

Pavlenko, Alexander

2011-06-01

The article provides results of analyzing special features of the single-bubble sonoluminescence, developing the special apparatus to investigate this phenomenon on a larger-scale basis. Certain very important effects of high energy density physics, i.e. liquid compressibility, shock-wave formation under the collapse of the gas cavity in liquid, shock-wave focusing in the gas-filled cavity, occurrence of hot dense plasma in the focusing area, and high-temperature radiation yield are observed in this phenomenon. Specificity of the process is conditioned by the ``ideal'' preparation and sphericity of the gas-and-liquid contact boundary what makes the collapse process efficient due to the reduced influence of hydrodynamic instabilities. Results of experimental investigations; results of developing the facilities, description of methods used to register parameters of facilities and the system under consideration; analytical estimates how gas-filled bubbles evolve in liquid with the regard for scale effects; results of preliminary 1-D gas dynamic calculations of the gas bubble evolution are presented. The work supported by ISTC Project #2116.

Shockwave therapy in the management of complex regional pain syndrome in medial femoral condyle of the knee.

PubMed

Notarnicola, Angela; Moretti, Lorenzo; Tafuri, Silvio; Panella, Antonio; Filipponi, Marco; Casalino, Alessio; Panella, Michele; Moretti, Biagio

2010-06-01

The aim of this prospective study was to assess the efficacy of shockwave (SW) therapy in the management of complex regional pain syndrome (CRPS). In this study, 30 patients (pts) who were affected by CRPS of the medial femoral condyle and unresponsive to previous standard physiotherapeutic and pharmacological treatment underwent 3 SW sessions at 72-h intervals, each consisting of 4000 shocks emitted by a MiniLith SL1 Storz electromagnetic generator. An energy flux density (EFD) of 0.035 or 0.09 mJ/mm(2) was used, depending on how well the patient endured the pain during the treatment. Satisfactory results were observed in 76.7% of the cases (23 pts) at the 2-month follow-up (FU) visit, and in 80% (24 pts) at the 6-month FU visit. The therapeutic effects of SW were caused by decreasing pain. The significant improvements we obtained bear witness to the potential value of SW therapy in the management of CRPS. Copyright 2010 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Shock tube and shock wave research; Proceedings of the Eleventh International Symposium, University of Washington, Seattle, Wash., July 11-14, 1977

NASA Technical Reports Server (NTRS)

Ahlborn, B. (Editor); Hertzberg, A.; Russell, D.

1978-01-01

Papers are presented on the applications of shock-wave technology to the study of hydrodynamics, the use of the pressure-wave machine for charging diesel engines, and measurements of the heat-transfer rate in gas-turbine components. Consideration is given to shock propagation along 90-degree bends, the explosive dissemination of liquids, and rotational and vibrational relaxation behind weak shock waves in water vapor. Shock phenomena associated with expansion flows are described and stratospheric-related research using the shock tube is outlined. Attention is given to shock-wave ignition of magnesium powders, Mach reflection and boundary layers, and transition in the shock-induced unsteady boundary layer on a flat plate. Shock-tube measurements of induction and post-induction rates for low-Btu gas mixtures are presented and shock-initiated ignition in COS-N2O-Ar mixtures is described. Cluster growth rates in supersaturated lead vapor are presented and a study of laser-induced plasma motion in a solenoidal magnetic field is reviewed.

Shock tube Multiphase Experiments

NASA Astrophysics Data System (ADS)

Middlebrooks, John; Allen, Roy; Paudel, Manoj; Young, Calvin; Musick, Ben; McFarland, Jacob

2017-11-01

Shock driven multiphase instabilities (SDMI) are unique physical phenomena that have far-reaching practical applications in engineering and science. The instability is present in high energy explosions, scramjet combustors, and supernovae events. The SDMI arises when a multiphase interface is impulsively accelerated by the passage of a shockwave. It is similar in development to the Richtmyer-Meshkov (RM) instability however, particle-to-gas coupling is the driving mechanism of the SDMI. As particle effects such as lag and phase change become more prominent, the SDMI's development begins to significantly deviate from the RM instability. We have developed an experiment for studying the SDMI in our shock tube facility. In our experiments, a multiphase interface is created using a laminar jet and flowed into the shock tube where it is accelerated by the passage of a planar shockwave. The interface development is captured using CCD cameras synchronized with planar laser illumination. This talk will give an overview of new experiments conducted to examine the development of a shocked cylindrical multiphase interface. The effects of Atwood number, particle size, and a second acceleration (reshock) of the interface will be discussed.

Design and Construction of a Shock Tube Experiment for Multiphase Instability Experiments

NASA Astrophysics Data System (ADS)

Middlebrooks, John; Black, Wolfgang; Avgoustopoulos, Constantine; Allen, Roy; Kathakapa, Raj; Guo, Qiwen; McFarland, Jacob

2016-11-01

Hydrodynamic instabilities are important phenomena that have a wide range of practical applications in engineering and physics. One such instability, the shock driven multiphase instability (SDMI), arises when a shockwave accelerates an interface between two particle-gas mixtures with differing multiphase properties. The SDMI is present in high energy explosives, scramjets, and supernovae. A practical way of studying shock wave driven instabilities is through experimentation in a shock tube laboratory. This poster presentation will cover the design and data acquisition process of the University of Missouri's Fluid Mixing Shock Tube Laboratory. In the shock tube, a pressure generated shockwave is passed through a multiphase interface, creating the SDMI instability. This can be photographed for observation using high speed cameras, lasers, and advance imaging techniques. Important experimental parameters such as internal pressure and temperature, and mass flow rates of gases can be set and recorded by remotely controlled devices. The experimental facility provides the University of Missouri's Fluid Mixing Shock Tube Laboratory with the ability to validate simulated experiments and to conduct further inquiry into the field of shock driven multiphase hydrodynamic instabilities. Advisor.

Experimental investigation of the micro-ramp based shock wave and turbulent boundary layer interaction control

NASA Astrophysics Data System (ADS)

Bo, Wang; Weidong, Liu; Yuxin, Zhao; Xiaoqiang, Fan; Chao, Wang

2012-05-01

Using a nanoparticle-based planar laser-scattering technique and supersonic particle image velocimetry, we investigated the effects of micro-ramp control on incident shockwave and boundary-layer interaction (SWBLI) in a low-noise supersonic wind-tunnel with Mach number 2.7 and Reynolds number Rθ = 5845. High spatiotemporal resolution wake structures downstream of the micro-ramps were detected, while a complex evolution process containing a streamwise counter-rotating vortex pair and large-scale hairpin-like vortices with Strouhal number Stδ of about 0.5-0.65 was revealed. The large-scale structures could survive while passing through the SWBLI region. Reflected shockwaves are clearly seen to be distorted accompanied by high-frequency fluctuations. Micro-ramp applications have a distinct influence on flow patterns of the SWBLI field that vary depending on spanwise locations. Both the shock foot and separation line exhibit undulations corresponding with modifications of the velocity distribution of the incoming boundary layer. Moreover, by energizing parts of the boundary flow, the micro-ramp is able to dampen the separation.

The α–ω phase transition in shock-loaded titanium

DOE PAGES

Jones, David R.; Morrow, Benjamin M.; Trujillo, Carl P.; ...

2017-07-28

Here, we present a series of experiments probing the martensitic α–ω (hexagonal close-packed to simple hexagonal) transition in titanium under shock-loading to peak stresses around 15 GPa. Gas-gun plate impact techniques were used to locate the α–ω transition stress with a laser-based velocimetry diagnostic. A change in the shock-wave profile at 10.1 GPa suggests the transition begins at this stress. A second experiment shock-loaded and then soft-recovered a similar titanium sample. We then analyzed this recovered material with electron-backscatter diffraction methods, revealing on average approximately 65% retained ω phase. Furthermore, based on careful analysis of the microstructure, we propose thatmore » the titanium never reached a full ω state, and that there was no observed phase-reversion from ω to α. Texture analysis suggests that any α titanium found in the recovered sample is the original α. The data show that both the α and ω phases are stable and can coexist even though the shock-wave presents as steady-state, at these stresses.« less

Calculation of reinforced-concrete frame strength under a simultaneous static cross section load and a column lateral impact

NASA Astrophysics Data System (ADS)

Belov, Nikolay; Yugov, Nikolay; Kopanitsa, Dmitry; Kopanitsa, Georgy; Yugov, Alexey; Kaparulin, Sergey; Plyaskin, Andrey; Kalichkina, Anna; Ustinov, Artyom

2016-01-01

When designing buildings with reinforced concrete that are planned to resist dynamic loads it is necessary to calculate this structural behavior under operational static and emergency impact and blast loads. Calculations of the structures under shock-wave loads can be performed by solving dynamic equations that do not consider static loads. Due to this fact the calculation of reinforced concrete frame under a simultaneous static and dynamic load in full 3d settings becomes a very non trivial and resource consuming problem. This problem can be split into two tasks. The first one is a shock-wave problem that can be solved using software package RANET-3, which allows solving the problem using finite elements method adapted for dynamic task. This method calculates strain-stress state of the material and its dynamic destruction, which is considered as growth and consolidation of micro defects under loading. On the second step the results of the first step are taken as input parameters for quasi static calculation of simultaneous static and dynamic load using finite elements method in AMP Civil Engineering-11.

In vitro study of the mechanical effects of shock-wave lithotripsy.

PubMed

Howard, D; Sturtevant, B

1997-01-01

Impulsive stress in repeated shock waves administered during extracorporeal shock-wave lithotripsy (ESWL) causes injury to kidney tissue. In a study of the mechanical input of ESWL, the effects of focused shock waves on thin planar polymeric membranes immersed in a variety of tissue-mimicking fluids have been examined. A direct mechanism of failure by shock compression and an indirect mechanism by bubble collapse have been observed. Thin membranes are easily damaged by bubble collapse. After propagating through cavitation-free acoustically heterogeneous media (liquids mixed with hollow glass spheres, and tissue) shock waves cause membranes to fail in fatigue by a shearing mechanism. As is characteristic of dynamic fatigue, the failure stress increases with strain rate, determined by the amplitude and rise time of the attenuated shock wave. Shocks with large amplitude and short rise time (i.e., in uniform media) cause no damage. Thus the inhomogeneity of tissue is likely to contribute to injury in ESWL. A definition of dose is proposed which yields a criterion for damage based on measurable shock wave properties.

Efficacy Management of Urolithiasis: Flexible Ureteroscopy versus Extracorporeal Shockwave Lithotripsy.

PubMed

Tauber, Volkmar; Wohlmuth, Martin; Hochmuth, Andreas; Schimetta, Wolfgang; Schimetta, Wofgang; Krause, F Steffen

2015-01-01

To evaluate the efficacy of flexible ureterscopy (fURS) and extracorporal shockwave lithotripsy (SWL) in the treatment of urolithiasis, complemented by a subgroup analysis of lower pole calyx. Retrospective analysis of patients treated by fURS or SWL was performed by independent variables such as gender, age, nephrolith size, double-J stent (DJ stent) and stone localisation. Out of 326 patients, 165 were treated by SWL and 161 by fURS. Complete stone removal was achieved by fURS in 83.2% and by SWL in 43.0% (p < 0.001). Asymptomatic behaviour (88-89%) and complication rate (10-11%) were nearly the same in both methods. A higher retreatment rate for SWL was necessary; otherwise, an auxillary DJ stent was performed more often preoperative before fURS. The subgroup analysis of lower pole calyx confirmed these evaluations. Complete stone-free removal was almost 8 times higher after fURS compared to SWL. The efficacy of fURS in treatment of urolithiasis is substantially higher than the efficacy of SWL. © 2015 S. Karger AG, Basel.

The interplay between rheology and pre-existing structures in the lithosphere and its influence on intraplate tectonics: Insights from scaled physical analogue models.

NASA Astrophysics Data System (ADS)

Santimano, T. N.; Adiban, P.; Pysklywec, R.

2017-12-01

The primary controls of deformation in the lithosphere are related to its rheological properties. In addition, recent work reveals that inherited zones of weakness in the deep lithosphere are prevalent and can also define tectonic activity. To understand how deformation is genetically related to rheology and/or pre-existing structures, we compare a set of physical analogue models with the presence and absence of a fault in the deep lithosphere. The layered lithosphere scaled models of a brittle upper crust, viscous lower crust and viscous mantle lithosphere are deformed in a convergent setting. Deformation of the model is recorded using high spatial and temporal stereoscopic cameras. We use Particle Image Velocimetry (PIV) to acquire a time-series dataset and study the velocity field and subsequently strain in the model. The finished model is also cut into cross-section revealing the finite internal structures that are then compared to the topography of the model. Preliminary results show that deformation in models with an inherited fault in the mantle lithosphere is accommodated by displacement along the fault plane that propagates into the overlying viscous lower crust and brittle upper crust. Here, the majority of the deformation is localized along the fault in a brittle manner. This is in contrast to the model absent of a fault that also displays significant amounts of deformation. In this setting, ductile deformation is accommodated by folding and thickening of the viscous layers and flexural shearing of the brittle upper crust. In these preliminary experiments, the difference in the strength profile between the mantle lithosphere and the lower crust is within the same order of magnitude. Future experiments will include models where the strength difference is an order of magnitude. This systematic study aids in understanding the role of rheology and deep structures particularly in transferring stress over time to the surface and is therefore fundamental in understanding intraplate tectonics and orogenesis.

Global geodynamic models constrained by tectonic reconstructions including plate deformation

NASA Astrophysics Data System (ADS)

Gurnis, M.; Flament, N.; Spasojevic, S.; Williams, S.; Seton, M.; Müller, R. D.

2011-12-01

In order to investigate the effect of mantle flow on the Earth's surface, imposing the kinematics predicted by plate reconstructions in global convection models has become common practice. Such models are valuable to investigate the effect of the mantle flow beneath the lithosphere on surface topography. Changes in surface topography due to lithospheric deformation are so far not part of top-down tectonic models in which plates are treated as rigid in traditional tectonic reconstructions. We introduce a new generation of geodynamic models that are based on tectonic reconstructions with deforming plates at both passive and convergent margins. These models allow us to investigate the relationships between lithospheric deformation and mantle flow, and their combined effects on surface topography. In traditional tectonic reconstructions, continents are represented as rigid blocks that either overlap or are separated by gaps in full-fit reconstructions. Reconstructions that include a global network of topological plate polygons avoid continental overlaps and gaps, but velocities are still derived on the basis of the Euler poles for rigid blocks. To resolve these issues, we developed a series of deforming plate models using the open source plate modeling software GPlates. For a given area, our methodology requires the relative motions between major rigid continental blocks, and a definition of the regions in which continental lithosphere deformed between these blocks. We use geophysical and geological data to define the limit between rigid and deforming areas, and the deformation history of non-rigid blocks. The velocity field predicted by these reconstructions is then used as a time-dependent surface boundary condition in global 3-D geodynamic models. To incorporate the continental lithosphere in our global models, we embed compositionally distinct crust and continental lithosphere within the thermal lithosphere. We define three isostatic columns of different thickness and buoyancy based on the tectonothermal age of the continents: Archean, Proterozoic and Phanerozoic. In the fourth isostatic column, the oceans, the thickness of the thermal lithosphere is assimilated using the half-space cooling model. We also use this capacity to define the thickness of the thermal lithosphere for different continental types, with the exception of the deforming areas that are fully dynamic. Finally, we introduce a new slab assimilation method in which the thermal structure of the slab, derived analytically, is progressively assimilated in the upper mantle into the dynamic models. This method not only improves the continuity of slabs in our models, but it also allows us to model flat slab segments that are particularly relevant for dynamic topography. This new generation of models allows us to analyse the contributions of continental deformation and of mantle flow to surface topography. We compare our results to geological and geophysical data, including stratigraphy, paleo-altimetry, paleo-environment and mantle tomography. This allows us to place constraints on key model parameters and to refine our knowledge of plate-mantle interactions during continental deformation.

Analysis and Modeling of Process of Residual Deformations Accumulation in Soils and Granular Materials

NASA Astrophysics Data System (ADS)

Aleksandrov, A. S.; Dolgih, G. V.; Kalinin, A. L.

2017-11-01

It is established that under the influence of repeated loads the process of plastic deformation in soils and discrete materials is hereditary. To perform the mathematical modeling of plastic deformation, the authors applied the integral equation by solution of which they manage to obtain the power and logarithmic dependencies connecting plastic deformation with the number of repeated loads, the parameters of the material and components of the stress tensor in the principal axes. It is shown that these dependences generalize a number of models proposed earlier in Russia and abroad. Based on the analysis of the experimental data obtained during material testing in the dynamic devices of triaxial compression at different values of the stress deviator, the coefficients in the proposed models of deformation are determined. The authors determined the application domain for logarithmic and degree dependences.

Biomechanical model for computing deformations for whole-body image registration: A meshless approach.

PubMed

Li, Mao; Miller, Karol; Joldes, Grand Roman; Kikinis, Ron; Wittek, Adam

2016-12-01

Patient-specific biomechanical models have been advocated as a tool for predicting deformations of soft body organs/tissue for medical image registration (aligning two sets of images) when differences between the images are large. However, complex and irregular geometry of the body organs makes generation of patient-specific biomechanical models very time-consuming. Meshless discretisation has been proposed to solve this challenge. However, applications so far have been limited to 2D models and computing single organ deformations. In this study, 3D comprehensive patient-specific nonlinear biomechanical models implemented using meshless Total Lagrangian explicit dynamics algorithms are applied to predict a 3D deformation field for whole-body image registration. Unlike a conventional approach that requires dividing (segmenting) the image into non-overlapping constituents representing different organs/tissues, the mechanical properties are assigned using the fuzzy c-means algorithm without the image segmentation. Verification indicates that the deformations predicted using the proposed meshless approach are for practical purposes the same as those obtained using the previously validated finite element models. To quantitatively evaluate the accuracy of the predicted deformations, we determined the spatial misalignment between the registered (i.e. source images warped using the predicted deformations) and target images by computing the edge-based Hausdorff distance. The Hausdorff distance-based evaluation determines that our meshless models led to successful registration of the vast majority of the image features. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Use of multiscale zirconium alloy deformation models in nuclear fuel behavior analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Montgomery, Robert; Tomé, Carlos; Liu, Wenfeng

Accurate prediction of cladding mechanical behavior is a key aspect of modeling nuclear fuel behavior, especially for conditions of pellet-cladding interaction (PCI), reactivity-initiated accidents (RIA), and loss of coolant accidents (LOCA). Current approaches to fuel performance modeling rely on empirical models for cladding creep, growth and plastic deformation, which are limited to the materials and conditions for which the models were developed. CASL has endeavored to improve upon this approach by incorporating a microstructurally-based, atomistically-informed, zirconium alloy mechanical deformation analysis capability into the BISON-CASL engineering scale fuel performance code. Specifically, the viscoplastic self-consistent (VPSC) polycrystal plasticity modeling approach, developed bymore » Lebensohn and Tome´ [2], has been coupled with BISON-CASL to represent the mechanistic material processes controlling the deformation behavior of the cladding. A critical component of VPSC is the representation of the crystallographic orientation of the grains within the matrix material and the ability to account for the role of texture on deformation. The multiscale modeling of cladding deformation mechanisms allowed by VPSC far exceed the functionality of typical semi-empirical constitutive models employed in nuclear fuel behavior codes to model irradiation growth and creep, thermal creep, or plasticity. This paper describes the implementation of an interface between VPSC and BISON-CASL and provides initial results utilizing the coupled functionality.« less

Real-time simulation of the nonlinear visco-elastic deformations of soft tissues.

PubMed

Basafa, Ehsan; Farahmand, Farzam

2011-05-01

Mass-spring-damper (MSD) models are often used for real-time surgery simulation due to their fast response and fairly realistic deformation replication. An improved real time simulation model of soft tissue deformation due to a laparoscopic surgical indenter was developed and tested. The mechanical realization of conventional MSD models was improved using nonlinear springs and nodal dampers, while their high computational efficiency was maintained using an adapted implicit integration algorithm. New practical algorithms for model parameter tuning, collision detection, and simulation were incorporated. The model was able to replicate complex biological soft tissue mechanical properties under large deformations, i.e., the nonlinear and viscoelastic behaviors. The simulated response of the model after tuning of its parameters to the experimental data of a deer liver sample, closely tracked the reference data with high correlation and maximum relative differences of less than 5 and 10%, for the tuning and testing data sets respectively. Finally, implementation of the proposed model and algorithms in a graphical environment resulted in a real-time simulation with update rates of 150 Hz for interactive deformation and haptic manipulation, and 30 Hz for visual rendering. The proposed real time simulation model of soft tissue deformation due to a laparoscopic surgical indenter was efficient, realistic, and accurate in ex vivo testing. This model is a suitable candidate for testing in vivo during laparoscopic surgery.

SU-F-J-138: An Extension of PCA-Based Respiratory Deformation Modeling Via Multi-Linear Decomposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iliopoulos, AS; Sun, X; Pitsianis, N

Purpose: To address and lift the limited degree of freedom (DoF) of globally bilinear motion components such as those based on principal components analysis (PCA), for encoding and modeling volumetric deformation motion. Methods: We provide a systematic approach to obtaining a multi-linear decomposition (MLD) and associated motion model from deformation vector field (DVF) data. We had previously introduced MLD for capturing multi-way relationships between DVF variables, without being restricted by the bilinear component format of PCA-based models. PCA-based modeling is commonly used for encoding patient-specific deformation as per planning 4D-CT images, and aiding on-board motion estimation during radiotherapy. However, themore » bilinear space-time decomposition inherently limits the DoF of such models by the small number of respiratory phases. While this limit is not reached in model studies using analytical or digital phantoms with low-rank motion, it compromises modeling power in the presence of relative motion, asymmetries and hysteresis, etc, which are often observed in patient data. Specifically, a low-DoF model will spuriously couple incoherent motion components, compromising its adaptability to on-board deformation changes. By the multi-linear format of extracted motion components, MLD-based models can encode higher-DoF deformation structure. Results: We conduct mathematical and experimental comparisons between PCA- and MLD-based models. A set of temporally-sampled analytical trajectories provides a synthetic, high-rank DVF; trajectories correspond to respiratory and cardiac motion factors, including different relative frequencies and spatial variations. Additionally, a digital XCAT phantom is used to simulate a lung lesion deforming incoherently with respect to the body, which adheres to a simple respiratory trend. In both cases, coupling of incoherent motion components due to a low model DoF is clearly demonstrated. Conclusion: Multi-linear decomposition can enable decoupling of distinct motion factors in high-rank DVF measurements. This may improve motion model expressiveness and adaptability to on-board deformation, aiding model-based image reconstruction for target verification. NIH Grant No. R01-184173.« less

Red blood cell dynamics: from cell deformation to ATP release.

PubMed

Wan, Jiandi; Forsyth, Alison M; Stone, Howard A

2011-10-01

The mechanisms of red blood cell (RBC) deformation under both static and dynamic, i.e., flow, conditions have been studied extensively since the mid 1960s. Deformation-induced biochemical reactions and possible signaling in RBCs, however, were proposed only fifteen years ago. Therefore, the fundamental relationship between RBC deformation and cellular signaling dynamics i.e., mechanotransduction, remains incompletely understood. Quantitative understanding of the mechanotransductive pathways in RBCs requires integrative studies of physical models of RBC deformation and cellular biochemical reactions. In this article we review the physical models of RBC deformation, spanning from continuum membrane mechanics to cellular skeleton dynamics under both static and flow conditions, and elaborate the mechanistic links involved in deformation-induced ATP release. This journal is © The Royal Society of Chemistry 2011

Preliminary deformation model for National Seismic Hazard map of Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meilano, Irwan; Gunawan, Endra; Sarsito, Dina

Preliminary deformation model for the Indonesia’s National Seismic Hazard (NSH) map is constructed as the block rotation and strain accumulation function at the elastic half-space. Deformation due to rigid body motion is estimated by rotating six tectonic blocks in Indonesia. The interseismic deformation due to subduction is estimated by assuming coupling on subduction interface while deformation at active fault is calculated by assuming each of the fault‘s segment slips beneath a locking depth or in combination with creeping in a shallower part. This research shows that rigid body motion dominates the deformation pattern with magnitude more than 15 mm/year, except inmore » the narrow area near subduction zones and active faults where significant deformation reach to 25 mm/year.« less

Damping Models for Shear-Deformable Beam with Applications to Spacecraft Wiring Harness

DTIC Science & Technology

2014-10-28

AFRL-RV-PS- TR-2014-0189 AFRL-RV-PS- TR-2014-0189 DAMPING MODELS FOR SHEAR-DEFORMABLE BEAM WITH APPLICATIONS TO SPACECRAFT WIRING HARNESS ...Feb 2012 4. TITLE AND SUBTITLE Damping Models for Shear-Deformable Beam with Applications to Spacecraft Wiring Harness 5a. CONTRACT NUMBER FA9453-12...behavior of wiring harnesses . The emphasis in this project will be on the extension of the shear-beam damping model to the Timoshenko beam, a beam model

Real-time deformation of human soft tissues: A radial basis meshless 3D model based on Marquardt's algorithm.

PubMed

Zhou, Jianyong; Luo, Zu; Li, Chunquan; Deng, Mi

2018-01-01

When the meshless method is used to establish the mathematical-mechanical model of human soft tissues, it is necessary to define the space occupied by human tissues as the problem domain and the boundary of the domain as the surface of those tissues. Nodes should be distributed in both the problem domain and on the boundaries. Under external force, the displacement of the node is computed by the meshless method to represent the deformation of biological soft tissues. However, computation by the meshless method consumes too much time, which will affect the simulation of real-time deformation of human tissues in virtual surgery. In this article, the Marquardt's Algorithm is proposed to fit the nodal displacement at the problem domain's boundary and obtain the relationship between surface deformation and force. When different external forces are applied, the deformation of soft tissues can be quickly obtained based on this relationship. The analysis and discussion show that the improved model equations with Marquardt's Algorithm not only can simulate the deformation in real-time but also preserve the authenticity of the deformation model's physical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Crustal deformation mechanism in southeastern Tibetan Plateau: Insights from numerical modeling

NASA Astrophysics Data System (ADS)

Li, Y.; Liu, S.; Chen, L.

2017-12-01

The Indo-Asian collision developed the complicated crustal deformation around the southeastern Tibetan plateau. Numerous models have proposed to explain the crustal deformation, but the mechanism remains controversial, especially the increasing multi-geophysics data, which demonstrate the existence of lower velocity, lower resistivity and high conductivity, implying that lower crustal flow is responsible for the crustal deformation, arguing for the lower crust flow model. To address the relations between the crust flow and the surface deformation, we employ a three-dimensional viscoelastic finite model to investigate the possible influence on the surface deformation, and discuss the stress field distribution under the model. Our preliminary results suggest that lower crustal flow plays an important role in crustal deformation in southeastern Tibetan plateau. The best fitting is achieved when the flow velocity of the lower crust is approximately 10-11 mm/a faster than that of the upper crust. Crustal rheological properties affect regional crustal deformation, when the viscosity of the middle and lower crust in the South China block reaches 1022 and 1023 Pa.s, respectively; the predicted match observations well, especially for the magnitude within the South China block. The maximum principal stress field exhibits clear zoning, gradually shifting from an approximately east-west orientation in the northern Bayan Har block to southeast in the South China block, southwest in the western Yunnan block, and a radially divergent distribution in the Middle Yunnan and Southern Yunnan blocks.

Deformation processes in orogenic wedges: New methods and application to Northwestern Washington State

NASA Astrophysics Data System (ADS)

Thissen, Christopher J.

Permanent deformation records aspects of how material moves through a tectonic environment. The methods required to measure deformation vary based on rock type, deformation process, and the geological question of interest. In this thesis we develop two new methods for measuring permanent deformation in rocks. The first method uses the autocorrelation function to measure the anisotropy present in two-dimensional photomicrographs and three-dimensional X-ray tomograms of rocks. The method returns very precise estimates for the deformation parameters and works best for materials where the deformation is recorded as a shape change of distinct fabric elements, such as grains. Our method also includes error estimates. Image analysis techniques can focus the method on specific fabric elements, such as quartz grains. The second method develops a statistical technique for measuring the symmetry in a distribution of crystal orientations, called a lattice-preferred orientation (LPO). We show that in many cases the symmetry of the LPO directly constrains the symmetry of the deformation, such axial flattening vs. pure shear vs. simple shear. In addition to quantifying the symmetry, the method uses the full crystal orientation to estimate symmetry rather than pole figures. Pole figure symmetry can often be misleading. This method works best for crystal orientations measured in samples deformed by dislocation creep, but otherwise can be used on any mineral without requiring information about slip systems. In Chapter 4 we show how deformation measurements can be used to inform regional tectonic and orogenic models in the Pacific Northwestern United States. A suite of measurements from the Olympic Mountains shows that uplift and deformation of the range is consistent with an orogenic wedge model driven by subduction of the Juan de Fuca plate, and not northward forearc migration of the Oregon block. The deformation measurements also show that deformation within the Olympic Mountains is essentially two-dimensional. We use this constraint to develop a suite of orogenic deformation models that use slab height and erosion rate data as boundary conditions. We use the models to show that influx of sediments distributed along an accretionary front can greatly reduce deformation required to maintain wedge taper. Due to the two-dimensional nature of deformation in the Olympics, a series of two-dimensional transects across the peninsula provides an approximation for non-elastic deformation across the Peninsula. We show how the shallow slab height and deeper exhumation at the core of peninsula led to the domal structure of the Olympics. This model also explains the counter-clockwise vertical axis rotations north of the peninsula, and clockwise rotations south of the peninsula through horizontal shear, similar to opening a gate. Finally, the horizontal surface velocities predicted by the models suggests that up to 15% of GPS velocities may reflect non-elastic, permanent translation of material towards the rear of the wedge.

Deformed Calogero-Sutherland model and fractional quantum Hall effect

NASA Astrophysics Data System (ADS)

Atai, Farrokh; Langmann, Edwin

2017-01-01

The deformed Calogero-Sutherland (CS) model is a quantum integrable system with arbitrary numbers of two types of particles and reducing to the standard CS model in special cases. We show that a known collective field description of the CS model, which is based on conformal field theory (CFT), is actually a collective field description of the deformed CS model. This provides a natural application of the deformed CS model in Wen's effective field theory of the fractional quantum Hall effect (FQHE), with the two kinds of particles corresponding to electrons and quasi-hole excitations. In particular, we use known mathematical results about super-Jack polynomials to obtain simple explicit formulas for the orthonormal CFT basis proposed by van Elburg and Schoutens in the context of the FQHE.

Challenging the foundations of the clinical model of foot function: further evidence that the root model assessments fail to appropriately classify foot function.

PubMed

Jarvis, Hannah L; Nester, Christopher J; Bowden, Peter D; Jones, Richard K

2017-01-01

The Root model of normal and abnormal foot function remains the basis for clinical foot orthotic practice globally. Our aim was to investigate the relationship between foot deformities and kinematic compensations that are the foundations of the model. A convenience sample of 140 were screened and 100 symptom free participants aged 18-45 years were invited to participate. The static biomechanical assessment described by the Root model was used to identify five foot deformities. A 6 segment foot model was used to measure foot kinematics during gait. Statistical tests compared foot kinematics between feet with and without foot deformities and correlated the degree of deformity with any compensatory motions. None of the deformities proposed by the Root model were associated with distinct differences in foot kinematics during gait when compared to those without deformities or each other. Static and dynamic parameters were not correlated. Taken as part of a wider body of evidence, the results of this study have profound implications for clinical foot health practice. We believe that the assessment protocol advocated by the Root model is no longer a suitable basis for professional practice. We recommend that clinicians stop using sub-talar neutral position during clinical assessments and stop assessing the non-weight bearing range of ankle dorsiflexion, first ray position and forefoot alignments and movement as a means of defining the associated foot deformities. The results question the relevance of the Root assessments in the prescription of foot orthoses.

X-ray peak broadening analysis of AA 6061{sub 100-x} - x wt.% Al{sub 2}O{sub 3} nanocomposite prepared by mechanical alloying

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivasankaran, S., E-mail: sivasankarangs1979@gmail.com; Sivaprasad, K., E-mail: ksp@nitt.edu; Narayanasamy, R., E-mail: narayan@nitt.edu

2011-07-15

Nanocrystalline AA 6061 alloy reinforced with alumina (0, 4, 8, and 12 wt.%) in amorphized state composite powder was synthesized by mechanical alloying and consolidated by conventional powder metallurgy route. The as-milled and as-sintered (573 K and 673 K) nanocomposites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The peaks corresponding to fine alumina was not observed by XRD patterns due to amorphization. Using high-resolution transmission electron microscope, it is confirmed that the presence of amorphized alumina observed in Al lattice fringes. The crystallite size, lattice strain, deformation stress, and strain energy density of AA 6061 matrixmore » were determined precisely from the first five most intensive reflection of XRD using simple Williamson-Hall models; uniform deformation model, uniform stress deformation model, and uniform energy density deformation model. Among the developed models, uniform energy density deformation model was observed to be the best fit and realistic model for mechanically alloyed powders. This model evidenced the more anisotropic nature of the ball milled powders. The XRD peaks of as-milled powder samples demonstrated a considerable broadening with percentage of reinforcement due to grain refinement and lattice distortions during same milling time (40 h). The as-sintered (673 K) unreinforced AA 6061 matrix crystallite size from well fitted uniform energy density deformation model was 98 nm. The as-milled and as-sintered (673 K) nanocrystallite matrix sizes for 12 wt.% Al{sub 2}O{sub 3} well fitted by uniform energy density deformation model were 38 nm and 77 nm respectively, which indicate that the fine Al{sub 2}O{sub 3} pinned the matrix grain boundary and prevented the grain growth during sintering. Finally, the lattice parameter of Al matrix in as-milled and as-sintered conditions was also investigated in this paper. Research highlights: {yields} Integral breadth methods using various Williamson-Hall models were investigated for line profile analysis. {yields} Uniform energy density deformation model is observed to the best realistic model. {yields} The present analysis is used for understanding the stress and the strain present in the nanocomposites.« less

Extracorporeal shock wave therapy for sacroiliac joint pain: A prospective, randomized, sham-controlled short-term trial.

PubMed

Moon, Young Eun; Seok, Hyun; Kim, Sang-Hyun; Lee, Seung Yeol; Yeo, Jung Ho

2017-01-01

Sacroiliac joint (SIJ) pain can cause lower back pain and pelvic discomfort. However, there is no established standard treatment for SIJ pain. Extracorporeal shock wave therapy (ESWT) is a novel, non-invasive therapeutic modality for musculoskeletal disorders. The mechanism underlying shockwave therapy is not fully understood, but the frequency with which ESWT is applied clinically has increased over the years. We evaluated the efficacy of using ESWT to treating SIJ pain. Thirty patients with SIJ pain were assigned randomly to ESWT (n = 15) and sham control (n = 15) groups. The ESWT group received 2,000 shockwaves with energy set to the maximum level tolerable by the patient (energy density = 0.09-0.25 mJ/mm2). The probe was oriented perpendicular to the posterior SIJ line, and moved up and down along the joint line. The sham control group received 2,000 shockwaves with the probe oriented parallel to the posterior SIJ line. A 10-cm numeric rating scale (NRS) and the Oswestry Disability Index (ODI) scores were assessed before the intervention, and 1 and 4 weeks post-intervention. Participants were instructed to refrain from using any other conservative treatment, including anti-inflammatory medication and other physical modalities during the study. In the ESWT group, NRS decreased significantly at post-treatment week 4 (3.64 (95% confidence interval, 2.29-4.99)) compared to baseline (6.42 (5.19-7.66); P < 0.05). ODI improved at 1 and 4 weeks compared to baseline, but not significantly. In the sham group, NRS and ODI did not differ at any post-treatment time point. There was a significant group difference in NRS at week 4 post-treatment (3.64 (2.29-4.99) in the ESWT group vs. 6.18 (5.34-7.02) in the sham control group; P < 0.05), but this was not the case for ODI. ESWT represents a potential therapeutic option for decreasing SIJ pain.

Reduction of Bubble Cavitation by Modifying the Diffraction Wave from a Lithotripter Aperture

PubMed Central

2012-01-01

Abstract Purpose A new method was devised to suppress the bubble cavitation in the lithotripter focal zone to reduce the propensity of shockwave-induced renal injury. Materials and Methods An edge extender was designed and fabricated to fit on the outside of the ellipsoidal reflector of an electrohydraulic lithotripter to disturb the generation of diffraction wave at the aperture, but with little effect on the acoustic field inside the reflector. Results Although the peak negative pressures at the lithotripter focus using the edge extender at 20 kV were similar to that of the original configuration (-11.1±0.9 vs −10.6±0.7 MPa), the duration of the tensile wave was shortened significantly (3.2±0.54 vs 5.83±0.56 μs, P<0.01). There is no difference, however, in both the amplitude and duration of the compressive shockwaves between these two configurations as well as the −6 dB beam width in the focal plane. The significant suppression effect of bubble cavitation was confirmed by the measured bubble collapse time using passive cavitation detection. At the lithotripter focus, while only about 30 shocks were needed to rupture a blood vessel phantom using the original HM-3 reflector at 20 kV, no damage could be produced after 300 shocks using the edge extender. Meanwhile, the original HM-3 lithotripter at 20 kV can achieve a stone comminution efficiency of 50.4±2.0% on plaster-of-Paris stone phantom after 200 shocks, which is comparable to that of using the edge extender (46.8±4.1%, P=0.005). Conclusions Modifying the diffraction wave at the lithotripter aperture can suppress the shockwave-induced bubble cavitation with significant reduced damage potential on the vessel phantom but satisfactory stone comminution ability. PMID:22332839

Shockwave treatment for medial tibial stress syndrome in military cadets: A single-blind randomized controlled trial.

PubMed

Gomez Garcia, Santiago; Ramon Rona, Silvia; Gomez Tinoco, Martha Claudia; Benet Rodriguez, Mikhail; Chaustre Ruiz, Diego Mauricio; Cardenas Letrado, Francia Piedad; Lopez-Illescas Ruiz, África; Alarcon Garcia, Juan Maria

2017-10-01

Medial tibial stress syndrome (MTSS) is a common injury in athletes and soldiers. Several studies have demonstrated the effectiveness of extracorporeal shockwave treatment (ESWT) in athletes with MTSS. To assess whether one session of focused ESWT is effective in the treatment of military cadets with MTSS. A randomized, prospective, controlled, single-blind, parallel-group clinical study. Ib. Military School of Cadets of the Colombian Army. Forty-two military cadets with unilateral chronic MTSS were randomly assigned to either one session of focused electromagnetic ESWT (1500 pulses at 0.20 mJ/mm 2 ) plus a specific exercise programme (muscle stretching and strengthening exercises) or the exercise programme alone. The primary endpoint was change in asymptomatic running test (RT) duration at four weeks from baseline. Secondary endpoints were changes in the visual analogue scale (VAS) after running and modified Roles and Maudsley (RM) score also at four weeks from baseline. ESWT patients were able to run longer. Mean RT after four weeks was 17 min 33 s (SE: 2.36) compared to 4 min 48 s (SE: 1.03) in the exercise-only group (p = 0.000). Mean VAS after running was 2.17 (SE: 0.44) in the ESWT group versus 4.26 (SE: 0.36) in the exercise-only group (p = 0.001). The ESWT group had a significantly higher RM score, with excellent or good results for 82.6% of patients vs. 36.8% in the exercise-only group (p = 0.002). No significant adverse effects of ESWT were observed. A single application of focused shockwave treatment in combination with a specific exercise programme accelerates clinical and functional recovery in military cadets with MTSS. Copyright © 2017 IJS Publishing Group Ltd. Published by Elsevier Ltd. All rights reserved.

Laser-generated shockwave for clearing medical device biofilms.

PubMed

Kizhner, Victor; Krespi, Yosef P; Hall-Stoodley, Luanne; Stoodley, Paul

2011-04-01

This study aimed to evaluate a laser method of biofilm interruption from the surface of various common medical devices and from surgically removed sinus tissue with adherent biofilms in a timely manner. Biofilm has emerged as a new threat not amenable to most antibiotic treatments. Biofilms, as opposed to planktonic bacteria, develop an extracellular polymeric slime matrix to facilitate adherence to host tissue or a prosthetic surface and to form a protective shield. A laser-induced biofilms disruption concept was previously described. Biofilms were grown in the laboratory on metallic and plastic medical device surfaces such as stents. Attempts to remove the biofilms with a laser were undertaken three times for each device. Q-switched Nd:YAG laser-generated shockwaves affecting Pseudomonas aeruginosa biofilms expressing yellow fluorescent protein (YFP) biofilm coating were applied with biologically safe parameters utilizing a fiber delivery system and a special probe. A confocal microscope was used to identify the biofilm structure prior to, during, and after laser application. The amount of biofilm removed from the medical devices in time was measured by quantifying green fluorescence. The biofilm fluctuated and eventually broke off the surface as shock waves neared the target. The time to remove 97.9 ± 0.4% (mean ± 1SD, n = 3) the biofilm from the surface of a Nitinol (NiTi) stent ranged from 4 to 10 s. The detached biofilm was observed floating in fluid media in various microscopic size particles. A new treatment modality using laser-generated shockwaves in the warfare against biofilms growing on surgical devices was demonstrated. Q-switched laser pulses stripped biofilm from the surface it adhered to, changing the bacteria to their planktonic form, making them amenable to conventional treatment. This therapeutic modality appears to be rapid, effective, and safe on metallic and plastic medical device surfaces.

Modelling ground deformation patterns associated with volcanic processes at the Okataina Volcanic Centre

NASA Astrophysics Data System (ADS)

Holden, L.; Cas, R.; Fournier, N.; Ailleres, L.

2017-09-01

The Okataina Volcanic Centre (OVC) is one of two large active rhyolite centres in the modern Taupo Volcanic Zone (TVZ) in the North Island of New Zealand. It is located in a complex section of the Taupo rift, a tectonically active section of the TVZ. The most recent volcanic unrest at the OVC includes the 1315 CE Kaharoa and 1886 Tarawera eruptions. Current monitoring activity at the OVC includes the use of continuous GPS receivers (cGPS), lake levelling and seismographs. The ground deformation patterns preceding volcanic activity the OVC are poorly constrained and restricted to predictions from basic modelling and comparison to other volcanoes worldwide. A better understanding of the deformation patterns preceding renewed volcanic activity is essential to determine if observed deformation is related to volcanic, tectonic or hydrothermal processes. Such an understanding also means that the ability of the present day cGPS network to detect these deformation patterns can also be assessed. The research presented here uses the finite element (FE) modelling technique to investigate ground deformation patterns associated with magma accumulation and diking processes at the OVC in greater detail. A number of FE models are produced and tested using Pylith software and incorporate characteristics of the 1315 CE Kaharoa and 1886 Tarawera eruptions, summarised from the existing body of research literature. The influence of a simple ring fault structure at the OVC on the modelled deformation is evaluated. The ability of the present-day continuous GPS (cGPS) GeoNet monitoring network to detect or observe the modelled deformation is also considered. The results show the modelled horizontal and vertical displacement fields have a number of key features, which include prominent lobe based regions extending northwest and southeast of the OVC. The results also show that the ring fault structure increases the magnitude of the displacements inside the caldera, in particular in the vicinity of the southern margin. As a result, some of the cGPS stations in the vicinity of the OVC are more important for measuring deformation related to volcanic processes than others. The results have important implications for how any future observed deformation at the OVC is observed and interpreted.

CPU-GPU mixed implementation of virtual node method for real-time interactive cutting of deformable objects using OpenCL.

PubMed

Jia, Shiyu; Zhang, Weizhong; Yu, Xiaokang; Pan, Zhenkuan

2015-09-01

Surgical simulators need to simulate interactive cutting of deformable objects in real time. The goal of this work was to design an interactive cutting algorithm that eliminates traditional cutting state classification and can work simultaneously with real-time GPU-accelerated deformation without affecting its numerical stability. A modified virtual node method for cutting is proposed. Deformable object is modeled as a real tetrahedral mesh embedded in a virtual tetrahedral mesh, and the former is used for graphics rendering and collision, while the latter is used for deformation. Cutting algorithm first subdivides real tetrahedrons to eliminate all face and edge intersections, then splits faces, edges and vertices along cutting tool trajectory to form cut surfaces. Next virtual tetrahedrons containing more than one connected real tetrahedral fragments are duplicated, and connectivity between virtual tetrahedrons is updated. Finally, embedding relationship between real and virtual tetrahedral meshes is updated. Co-rotational linear finite element method is used for deformation. Cutting and collision are processed by CPU, while deformation is carried out by GPU using OpenCL. Efficiency of GPU-accelerated deformation algorithm was tested using block models with varying numbers of tetrahedrons. Effectiveness of our cutting algorithm under multiple cuts and self-intersecting cuts was tested using a block model and a cylinder model. Cutting of a more complex liver model was performed, and detailed performance characteristics of cutting, deformation and collision were measured and analyzed. Our cutting algorithm can produce continuous cut surfaces when traditional minimal element creation algorithm fails. Our GPU-accelerated deformation algorithm remains stable with constant time step under multiple arbitrary cuts and works on both NVIDIA and AMD GPUs. GPU-CPU speed ratio can be as high as 10 for models with 80,000 tetrahedrons. Forty to sixty percent real-time performance and 100-200 Hz simulation rate are achieved for the liver model with 3,101 tetrahedrons. Major bottlenecks for simulation efficiency are cutting, collision processing and CPU-GPU data transfer. Future work needs to improve on these areas.

Plate Like Convection with Viscous Strain Weakening and Corresponding Surface Deformation Pattern

NASA Astrophysics Data System (ADS)

Fuchs, L.; Becker, T. W.

2017-12-01

How plate tectonic surface motions are generated by mantle convection on Earth and possibly other terrestrial type planets has recently become more readily accessible with fully dynamic convection computations. However, it remains debated how plate-like the behavior in such models truly is, and in particular how the well plate boundary dynamics are captured in models which typically exclude the effects of deformation history and memory. Here, we analyze some of the effects of viscous strain weakening on plate behavior and the interactions between interior convection dynamics and surface deformation patterns. We use the finite element code CitcomCU to model convection in a 3D Cartesian model setup. The models are internally heated, with an Arrhenius-type temperature dependent viscosity including plastic yielding and viscous strain weakening (VSW) and healing (VSWH). VSW can mimic first order features of more complex damage mechanisms such as grain-size dependent rheology. Besides plate diagnostic parameters (Plateness, Mobility, and Toroidal: Poloidal ratio) to analyze the tectonic behavior our models, we also explore how "plate boundaries" link to convective patterns. In a first model series, we analyze general surface deformation patterns without VSW. In the early stages, deformation patterns are clearly co-located with up- and downwelling limbs of convection. Along downwellings strain-rates are high and localized, whereas upwellings tend to lead to broad zones of high deformation. At a more advanced stage, however, the plates' interior is highly deformed due to continuous strain accumulation and resurfaced inherited strain. Including only VSW leads to more localized deformation along downwellings. However, at a more advanced stage plate-like convection fails due an overall weakening of the material. This is prevented including strain healing. Deformation pattern at the surface more closely coincide with the internal convection patterns. The average surface deformation is reduced significantly and mainly governed by the location of the up- and downwellings. VSWH thereby affects plate dynamics due to two main properties: the intensity of weakening with increasing strain and the strain healing rate. As both increase, mobility increases as well and strain becomes more localized at the downwellings.

Direct measurement of erythrocyte deformability in diabetes mellitus with a transparent microchannel capillary model and high-speed video camera system.

PubMed

Tsukada, K; Sekizuka, E; Oshio, C; Minamitani, H

2001-05-01

To measure erythrocyte deformability in vitro, we made transparent microchannels on a crystal substrate as a capillary model. We observed axisymmetrically deformed erythrocytes and defined a deformation index directly from individual flowing erythrocytes. By appropriate choice of channel width and erythrocyte velocity, we could observe erythrocytes deforming to a parachute-like shape similar to that occurring in capillaries. The flowing erythrocytes magnified 200-fold through microscopy were recorded with an image-intensified high-speed video camera system. The sensitivity of deformability measurement was confirmed by comparing the deformation index in healthy controls with erythrocytes whose membranes were hardened by glutaraldehyde. We confirmed that the crystal microchannel system is a valuable tool for erythrocyte deformability measurement. Microangiopathy is a characteristic complication of diabetes mellitus. A decrease in erythrocyte deformability may be part of the cause of this complication. In order to identify the difference in erythrocyte deformability between control and diabetic erythrocytes, we measured erythrocyte deformability using transparent crystal microchannels and a high-speed video camera system. The deformability of diabetic erythrocytes was indeed measurably lower than that of erythrocytes in healthy controls. This result suggests that impaired deformability in diabetic erythrocytes can cause altered viscosity and increase the shear stress on the microvessel wall. Copyright 2001 Academic Press.

Original Size and Shape of the Sudbury Structure

NASA Technical Reports Server (NTRS)

Lowman, P. D., Jr.

1997-01-01

This paper presents new evidence bearing on the original size and shape of the Sudbury impact structure. Current opinion is almost unanimous that the structure is a multiring basin with an original diameter of about 200 km and a circular shape that has since been shortened in a northwest-southeast direction by Penokean deformation Evidence for this interpretation, collected chiefly from north of the Sudbury Igneous Complex (SIC), includes supposed outer rings on Landsat imagery, distant occurrences of "Sudbury breccia" (generally defined as pseudotachylite), shatter cone occurrences, and outliers of Huronian sedimentary rock thought to be down-faulted rings. New data from imaging radar and field work north of the SIC, however, contradict this evidence. Radar imagery shows no signs of the supposed outer rings mapped by earlier workers on Landsat images. The most prominent ring has been found to be a chance alignment of two independent fracture sets. Radar imagery from the CCRS Convair 580, with look direction almost normal to the north rim of the SIC, shows no evidence of the rings despite strong look azimuth highlighting. Radar imagery has shown many unmapped diabase dikes north of the SIC. Several exposures of supposed Sudbury breccia are associated with these dikes or with Nipissing diabase intrusions, in some cases actually inside the dikes or directly continuous with them. They appear to be igneous intrusion breccias with no relation to impact. Shock-wave interaction at lithologic contacts cannot be invoked for most of these, because they are part of a northwest trending swarm cutting the SIC in the North Range, and hence too young for an impact origin. Similar diabase-related breccias and pseudotachylite-like veins have been found far outside the Sudbury area between Chapleau and Thessalon. Shatter cones north of the SIC are few and poorly developed, perhaps due to the coarse-grained Footwall rock, and cannot be considered a continuous zone analogous to their occurrence on the South Range in Huronian rocks. Supposed down-faulted outliers of Huronian rocks north of the SIC show no consistent relation to faulting, and the Huronian/Archean contact is locally erosional. Radar imagery and field-checking confirm Rousell's conclusion that the North Range has undergone little or no Penokean deformation. T'his implies that the plan view outline of the crater (floor of the SIC) is original. Extrapolation of the North Range as part of a circular arc leads to an impossibly great diameter. It is concluded that although Penokean deformation largely accounts for the structure's shape, the original crater was not circular and was much smaller than 200 km across.

Deformation behaviors of peat with influence of organic matter.

PubMed

Yang, Min; Liu, Kan

2016-01-01

Peat is a kind of special material rich in organic matter. Because of the high content of organic matter, it shows different deformation behaviors from conventional geotechnical materials. Peat grain has a non-negligible compressibility due to the presence of organic matter. Biogas can generate from peat and can be trapped in form of gas bubbles. Considering the natural properties of peat, a special three-phase composition of peat is described which indicates the existence of organic matter and gas bubbles in peat. A stress-strain-time model is proposed for the compression of organic matter, and the surface tension effect is considered in the compression model of gas bubbles. Finally, a mathematical model has been developed to simulate the deformation behavior of peat considering the compressibility of organic matter and entrapped gas bubbles. The deformation process is the coupling of volume variation of organic matter, gas bubbles and water drainage. The proposed model is used to simulate a series of peat laboratory oedometer tests, and the model can well capture the test results with reasonable model parameters. Effects of model parameters on deformation of peat are also analyzed.

Deformation rates across the San Andreas Fault system, central California determined by geology and geodesy

NASA Astrophysics Data System (ADS)

Titus, Sarah J.

The San Andreas fault system is a transpressional plate boundary characterized by sub-parallel dextral strike-slip faults separating internally deformed crustal blocks in central California. Both geodetic and geologic tools were used to understand the short- and long-term partitioning of deformation in both the crust and the lithospheric mantle across the plate boundary system. GPS data indicate that the short-term discrete deformation rate is ˜28 mm/yr for the central creeping segment of the San Andreas fault and increases to 33 mm/yr at +/-35 km from the fault. This gradient in deformation rates is interpreted to reflect elastic locking of the creeping segment at depth, distributed off-fault deformation, or some combination of these two mechanisms. These short-term fault-parallel deformation rates are slower than the expected geologic slip rate and the relative plate motion rate. Structural analysis of folds and transpressional kinematic modeling were used to quantify long-term distributed deformation adjacent to the Rinconada fault. Folding accommodates approximately 5 km of wrench deformation, which translates to a deformation rate of ˜1 mm/yr since the start of the Pliocene. Integration with discrete offset on the Rinconada fault indicates that this portion of the San Andreas fault system is approximately 80% strike-slip partitioned. This kinematic fold model can be applied to the entire San Andreas fault system and may explain some of the across-fault gradient in deformation rates recorded by the geodetic data. Petrologic examination of mantle xenoliths from the Coyote Lake basalt near the Calaveras fault was used to link crustal plate boundary deformation at the surface with models for the accommodation of deformation in the lithospheric mantle. Seismic anisotropy calculations based on xenolith petrofabrics suggest that an anisotropic mantle layer thickness of 35-85 km is required to explain the observed shear wave splitting delay times in central California. The available data are most consistent with models for a broad zone of distributed deformation in the lithospheric mantle.

Twisted supersymmetry: Twisted symmetry versus renormalizability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dimitrijevic, Marija; Nikolic, Biljana; Radovanovic, Voja

We discuss a deformation of superspace based on a Hermitian twist. The twist implies a *-product that is noncommutative, Hermitian and finite when expanded in a power series of the deformation parameter. The Leibniz rule for the twisted supersymmetry transformations is deformed. A minimal deformation of the Wess-Zumino action is proposed and its renormalizability properties are discussed. There is no tadpole contribution, but the two-point function diverges. We speculate that the deformed Leibniz rule, or more generally the twisted symmetry, interferes with renormalizability properties of the model. We discuss different possibilities to render a renormalizable model.

Dynamic soft tissue deformation estimation based on energy analysis

NASA Astrophysics Data System (ADS)

Gao, Dedong; Lei, Yong; Yao, Bin

2016-10-01

The needle placement accuracy of millimeters is required in many needle-based surgeries. The tissue deformation, especially that occurring on the surface of organ tissue, affects the needle-targeting accuracy of both manual and robotic needle insertions. It is necessary to understand the mechanism of tissue deformation during needle insertion into soft tissue. In this paper, soft tissue surface deformation is investigated on the basis of continuum mechanics, where a geometry model is presented to quantitatively approximate the volume of tissue deformation. The energy-based method is presented to the dynamic process of needle insertion into soft tissue based on continuum mechanics, and the volume of the cone is exploited to quantitatively approximate the deformation on the surface of soft tissue. The external work is converted into potential, kinetic, dissipated, and strain energies during the dynamic rigid needle-tissue interactive process. The needle insertion experimental setup, consisting of a linear actuator, force sensor, needle, tissue container, and a light, is constructed while an image-based method for measuring the depth and radius of the soft tissue surface deformations is introduced to obtain the experimental data. The relationship between the changed volume of tissue deformation and the insertion parameters is created based on the law of conservation of energy, with the volume of tissue deformation having been obtained using image-based measurements. The experiments are performed on phantom specimens, and an energy-based analytical fitted model is presented to estimate the volume of tissue deformation. The experimental results show that the energy-based analytical fitted model can predict the volume of soft tissue deformation, and the root mean squared errors of the fitting model and experimental data are 0.61 and 0.25 at the velocities 2.50 mm/s and 5.00 mm/s. The estimating parameters of the soft tissue surface deformations are proven to be useful for compensating the needle-targeting error in the rigid needle insertion procedure, especially for percutaneous needle insertion into organs.

Field-scale and wellbore modeling of compaction-induced casing failures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hilbert, L.B. Jr.; Gwinn, R.L.; Moroney, T.A.

1999-06-01

Presented in this paper are the results and verification of field- and wellbore-scale large deformation, elasto-plastic, geomechanical finite element models of reservoir compaction and associated casing damage. The models were developed as part of a multidisciplinary team project to reduce the number of costly well failures in the diatomite reservoir of the South Belridge Field near Bakersfield, California. Reservoir compaction of high porosity diatomite rock induces localized shearing deformations on horizontal weak-rock layers and geologic unconformities. The localized shearing deformations result in casing damage or failure. Two-dimensional, field-scale finite element models were used to develop relationships between field operations, surfacemore » subsidence, and shear-induced casing damage. Pore pressures were computed for eighteen years of simulated production and water injection, using a three-dimensional reservoir simulator. The pore pressures were input to the two-dimensional geomechanical field-scale model. Frictional contact surfaces were used to model localized shear deformations. To capture the complex casing-cement-rock interaction that governs casing damage and failure, three-dimensional models of a wellbore were constructed, including a frictional sliding surface to model localized shear deformation. Calculations were compared to field data for verification of the models.« less

Modeling crustal deformation near active faults and volcanic centers: a catalog of deformation models and modeling approaches

USGS Publications Warehouse

Battaglia, Maurizio; ,; Peter, F.; Murray, Jessica R.

2013-01-01

This manual provides the physical and mathematical concepts for selected models used to interpret deformation measurements near active faults and volcanic centers. The emphasis is on analytical models of deformation that can be compared with data from the Global Positioning System (GPS) receivers, Interferometric synthetic aperture radar (InSAR), leveling surveys, tiltmeters and strainmeters. Source models include pressurized spherical, ellipsoidal, and horizontal penny-shaped geometries in an elastic, homogeneous, flat half-space. Vertical dikes and faults are described following the mathematical notation for rectangular dislocations in an elastic, homogeneous, flat half-space. All the analytical expressions were verified against numerical models developed by use of COMSOL Multyphics, a Finite Element Analysis software (http://www.comsol.com). In this way, typographical errors present were identified and corrected. Matlab scripts are also provided to facilitate the application of these models.

Investigating the long-term geodetic response to magmatic intrusions at volcanoes in northern California

NASA Astrophysics Data System (ADS)

Parker, A. L.; Biggs, J.; Annen, C.; Houseman, G. A.; Yamasaki, T.; Wright, T. J.; Walters, R. J.; Lu, Z.

2014-12-01

Ratios of intrusive to extrusive activity at volcanic arcs are thought to be high, with estimates ranging between 5:1 and 30:1. Understanding the geodetic response to magmatic intrusion is therefore fundamental to large-scale studies of volcano deformation, providing insight into the dynamics of the inter-eruptive period of the volcano cycle and the building of continental crust. In northern California, we identify two volcanoes - Medicine Lake Volcano (MLV) and Lassen Volcanic Center (LaVC) - that exhibit long-term (multi-decadal) subsidence. We test the hypothesis that deformation at these volcanoes results from processes associated with magmatic intrusions. We first constrain the spatial and temporal characteristics of the deformation fields, establishing the first time-series of deformation at LaVC using InSAR data, multi-temporal analysis techniques and global weather models. Although the rates of deformation at the two volcanoes are similar (~1 cm/yr), our results show that the ratio of vertical to horizontal displacements is significantly different, suggesting contrasting source geometries. To test the origin of deformation, we develop modeling strategies to investigate thermal and viscoelastic processes associated with magmatic intrusions. The first model we develop couples analytical geodetic models to a numerical model of volume loss due to cooling and crystallization based upon temperature-melt fraction relationships from petrological experiments. This model provides evidence that magmatic intrusion at MLV has occurred more recently than the last eruption ~1 ka. The second model we test uses a finite element approach to simulate the time-dependent viscoelastic response of the crust to magmatic intrusion. We assess the magnitude and timescales of ground deformation that may result from these processes, exploring the model parameter space before applying the models to our InSAR observations of subsidence in northern California.

Computational approach to seasonal changes of living leaves.

PubMed

Tang, Ying; Wu, Dong-Yan; Fan, Jing

2013-01-01

This paper proposes a computational approach to seasonal changes of living leaves by combining the geometric deformations and textural color changes. The geometric model of a leaf is generated by triangulating the scanned image of a leaf using an optimized mesh. The triangular mesh of the leaf is deformed by the improved mass-spring model, while the deformation is controlled by setting different mass values for the vertices on the leaf model. In order to adaptively control the deformation of different regions in the leaf, the mass values of vertices are set to be in proportion to the pixels' intensities of the corresponding user-specified grayscale mask map. The geometric deformations as well as the textural color changes of a leaf are used to simulate the seasonal changing process of leaves based on Markov chain model with different environmental parameters including temperature, humidness, and time. Experimental results show that the method successfully simulates the seasonal changes of leaves.

Modeling deformation and chaining of flexible shells in a nematic solvent with finite elements on an adaptive moving mesh

NASA Astrophysics Data System (ADS)

DeBenedictis, Andrew; Atherton, Timothy J.; Rodarte, Andrea L.; Hirst, Linda S.

2018-03-01

A micrometer-scale elastic shell immersed in a nematic liquid crystal may be deformed by the host if the cost of deformation is comparable to the cost of elastic deformation of the nematic. Moreover, such inclusions interact and form chains due to quadrupolar distortions induced in the host. A continuum theory model using finite elements is developed for this system, using mesh regularization and dynamic refinement to ensure quality of the numerical representation even for large deformations. From this model, we determine the influence of the shell elasticity, nematic elasticity, and anchoring condition on the shape of the shell and hence extract parameter values from an experimental realization. Extending the model to multibody interactions, we predict the alignment angle of the chain with respect to the host nematic as a function of aspect ratio, which is found to be in excellent agreement with experiments.

A review of virtual cutting methods and technology in deformable objects.

PubMed

Wang, Monan; Ma, Yuzheng

2018-06-05

Virtual cutting of deformable objects has been a research topic for more than a decade and has been used in many areas, especially in surgery simulation. We refer to the relevant literature and briefly describe the related research. The virtual cutting method is introduced, and we discuss the benefits and limitations of these methods and explore possible research directions. Virtual cutting is a category of object deformation. It needs to represent the deformation of models in real time as accurately, robustly and efficiently as possible. To accurately represent models, the method must be able to: (1) model objects with different material properties; (2) handle collision detection and collision response; and (3) update the geometry and topology of the deformable model that is caused by cutting. Virtual cutting is widely used in surgery simulation, and research of the cutting method is important to the development of surgery simulation. Copyright © 2018 John Wiley & Sons, Ltd.

Fast spinning strings on η deformed AdS 5 × S 5

NASA Astrophysics Data System (ADS)

Banerjee, Aritra; Bhattacharyya, Arpan; Roychowdhury, Dibakar

2018-02-01

In this paper, considering the correspondence between spin chains and string sigma models, we explore the rotating string solutions over η deformed AdS 5 × S 5 in the so-called fast spinning limit. In our analysis, we focus only on the bosonic part of the full superstring action and compute the relevant limits on both ( R × S 3) η and ( R × S 5) η models. The resulting system reveals that in the fast spinning limit, the sigma model on η deformed S 5 could be approximately thought of as the continuum limit of anisotropic SU(3) Heisenberg spin chain model. We compute the energy for a certain class of spinning strings in deformed S 5 and we show that this energy can be mapped to that of a similar spinning string in the purely imaginary β deformed background.

Zygomatic bone shape in intentional cranial deformations: a model for the study of the interactions between skull growth and facial morphology.

PubMed

Ketoff, S; Girinon, F; Schlager, S; Friess, M; Schouman, T; Rouch, P; Khonsari, R H

2017-04-01

Intentional cranial deformations (ICD) were obtained by exerting external mechanical constraints on the skull vault during the first years of life to permanently modify head shape. The repercussions of ICD on the face are not well described in the midfacial region. Here we assessed the shape of the zygomatic bone in different types of ICDs. We considered 14 non-deformed skulls, 19 skulls with antero-posterior deformation, nine skulls with circumferential deformation and seven skulls with Toulouse deformation. The shape of the zygomatic bone was assessed using a statistical shape model after mesh registration. Euclidian distances between mean models and Mahalanobis distances after canonical variate analysis were computed. Classification accuracy was computed using a cross-validation approach. Different ICDs cause specific zygomatic shape modifications corresponding to different degrees of retrusion but the shape of the zygomatic bone alone is not a sufficient parameter for classifying populations into ICD groups defined by deformation types. We illustrate the fact that external mechanical constraints on the skull vault influence midfacial growth. ICDs are a model for the study of the influence of epigenetic factors on craniofacial growth and can help to understand the facial effects of congenital skull malformations such as single or multi-suture synostoses, or of external orthopedic devices such as helmets used to correct deformational plagiocephaly. © 2016 Anatomical Society.

The relationship between digital model accuracy and time-dependent deformation of alginate impressions.

PubMed

Alcan, Toros; Ceylanoğlu, Cenk; Baysal, Bekir

2009-01-01

To investigate the effects of different storage periods of alginate impressions on digital model accuracy. A total of 105 impressions were taken from a master model with three different brands of alginates and were poured into stone models in five different storage periods. In all, 21 stone models were poured and immediately were scanned, and 21 digital models were prepared. The remaining 84 impressions were poured after 1, 2, 3, and 4 days, respectively. Five linear measurements were made by three researchers on the master model, the stone models, and the digital models. Time-dependent deformation of alginate impressions at different storage periods and the accuracy of traditional stone models and digital models were evaluated separately. Both the stone models and the digital models were highly correlated with the master model. Significant deformities in the alginate impressions were noted at different storage periods of 1 to 4 days. Alginate impressions of different brands also showed significant differences between each other on the first, third, and fourth days. Digital orthodontic models are as reliable as traditional stone models and probably will become the standard for orthodontic clinical use. Storing alginate impressions in sealed plastic bags for up to 4 days caused statistically significant deformation of alginate impressions, but the magnitude of these deformations did not appear to be clinically relevant and had no adverse effect on digital modeling.

An inverse approach to constraining strain and vorticity using rigid clast shape preferred orientation data

NASA Astrophysics Data System (ADS)

Davis, Joshua R.; Giorgis, Scott

2014-11-01

We describe a three-part approach for modeling shape preferred orientation (SPO) data of spheroidal clasts. The first part consists of criteria to determine whether a given SPO and clast shape are compatible. The second part is an algorithm for randomly generating spheroid populations that match a prescribed SPO and clast shape. In the third part, numerical optimization software is used to infer deformation from spheroid populations, by finding the deformation that returns a set of post-deformation spheroids to a minimally anisotropic initial configuration. Two numerical experiments explore the strengths and weaknesses of this approach, while giving information about the sensitivity of the model to noise in data. In monoclinic transpression of oblate rigid spheroids, the model is found to constrain the shortening component but not the simple shear component. This modeling approach is applied to previously published SPO data from the western Idaho shear zone, a monoclinic transpressional zone that deformed a feldspar megacrystic gneiss. Results suggest at most 5 km of shortening, as well as pre-deformation SPO fabric. The shortening estimate is corroborated by a second model that assumes no pre-deformation fabric.

A constrained maximization formulation to analyze deformation of fiber reinforced elastomeric actuators

NASA Astrophysics Data System (ADS)

Singh, Gaurav; Krishnan, Girish

2017-06-01

Fiber reinforced elastomeric enclosures (FREEs) are soft and smart pneumatic actuators that deform in a predetermined fashion upon inflation. This paper analyzes the deformation behavior of FREEs by formulating a simple calculus of variations problem that involves constrained maximization of the enclosed volume. The model accurately captures the deformed shape for FREEs with any general fiber angle orientation, and its relation with actuation pressure, material properties and applied load. First, the accuracy of the model is verified with existing literature and experiments for the popular McKibben pneumatic artificial muscle actuator with two equal and opposite families of helically wrapped fibers. Then, the model is used to predict and experimentally validate the deformation behavior of novel rotating-contracting FREEs, for which no prior literature exist. The generality of the model enables conceptualization of novel FREEs whose fiber orientations vary arbitrarily along the geometry. Furthermore, the model is deemed to be useful in the design synthesis of fiber reinforced elastomeric actuators for general axisymmetric desired motion and output force requirement.

A finite element head and neck model as a supportive tool for deformable image registration.

PubMed

Kim, Jihun; Saitou, Kazuhiro; Matuszak, Martha M; Balter, James M

2016-07-01

A finite element (FE) head and neck model was developed as a tool to aid investigations and development of deformable image registration and patient modeling in radiation oncology. Useful aspects of a FE model for these purposes include ability to produce realistic deformations (similar to those seen in patients over the course of treatment) and a rational means of generating new configurations, e.g., via the application of force and/or displacement boundary conditions. The model was constructed based on a cone-beam computed tomography image of a head and neck cancer patient. The three-node triangular surface meshes created for the bony elements (skull, mandible, and cervical spine) and joint elements were integrated into a skeletal system and combined with the exterior surface. Nodes were additionally created inside the surface structures which were composed of the three-node triangular surface meshes, so that four-node tetrahedral FE elements were created over the whole region of the model. The bony elements were modeled as a homogeneous linear elastic material connected by intervertebral disks. The surrounding tissues were modeled as a homogeneous linear elastic material. Under force or displacement boundary conditions, FE analysis on the model calculates approximate solutions of the displacement vector field. A FE head and neck model was constructed that skull, mandible, and cervical vertebrae were mechanically connected by disks. The developed FE model is capable of generating realistic deformations that are strain-free for the bony elements and of creating new configurations of the skeletal system with the surrounding tissues reasonably deformed. The FE model can generate realistic deformations for skeletal elements. In addition, the model provides a way of evaluating the accuracy of image alignment methods by producing a ground truth deformation and correspondingly simulated images. The ability to combine force and displacement conditions provides flexibility for simulating realistic anatomic configurations.

Effect of decollement rheology and deformation rate on the structural development of fold thrust belts in sand box models and their implications for the Naga fold thrust belt (NE India)

NASA Astrophysics Data System (ADS)

Saha, B.; Dietl, C.

2009-04-01

Previous studies on decollement kinematics have shed light on the differing structures of fold thrust belt forming above lithologically different decollements, such as shales, carbonates and evaporites. Factors, affecting the decollement kinematics most are (1) rock rheology and (2) deformation rate. This study is intended to explain the deformation style of the Naga fold thrust belt (NFTB, NE India) with the aid of sand box modelling performed at a basal temperature of 50C and deformed at varying strain rates from 3*10-6 s-1 to 4*10-3 s-1. The models are made up (from bottom to top) of a 0.25 cm thick layer of temperature-sensitive PDMS (polydimethylsiloxane), overlain by 1.75 cm of alternating black and yellow sand. The basal PDMS layer simulates a shale decollement. Decollements in the NFTB are generally developed in the Barail Shale of Oligocene age at 50C (the depth of the Barail Shale is about 2 km and the prevailing geothermal gradient is 25C/km). The sand layers simulate the brittlely behaving sandstones which prevail in the NFTB. All of the models were subjected to 35% compression, as the NFTB experienced similar shortening. The varying deformation velocities were chosen to model differing decollement rheologies. PDMS simulates shale decollement, which is mobile when overpressured and undergoes compression. The rheology of PDMS changes considerably with the applied temperature and strain rate. PDMS, although generally regarded as Newtonian, does behave non-Newtonian at strain rates of 10-3 s-1. The relation between decollement pore fluid overpressure with that of model strain rate, the material rheology, scaled body forces, density of the decollement in nature can be expressed as: λ = 1- [ V ηmodel / f Hmodel ρnatureg Hnature σ*] where λ = coeifficient of pore fluid overpressure in the decollement, V = the deformation velocity with which the models are deforming, ηmodel= viscosity of the decollement material, f = the co efficient of overpressure, and is estimated 0.85 for frictional decollement, Hmodel = thickness of the decollement in the models, ρnature = density of the shale decollement in its natural analogue, g = the acceleration of gravity, Hnature = thickness of the decollement in nature, σ* = the scaled body forces. Hence, it can be suggested that, the value of pore fluid overpressure is dependent on the variables like velocity of the deformation, viscosity and thickness of the model decollement, nature to model ratio of body forces, density and thickness of the natural analogues. The values for natural analogue and model decollement thickness are constant, only the viscosity (dependent on temperature and applied strain rate) varies with different models, in turn altering the co efficient of overpressure values. Rapid shortening rates (model group 1, deforming at a strain rate varying from 4*10-5 s-1 to 4*10-3 s-1) generate more complicated structures than that of those shortening at lower rates (model group 2, deforming at a strain rate varying from 3*10-6 s-1 to 1.6*10-5 s-1). Thrust related folds predominate in model group 1, whereas, thrusts and backthursts dominate in model group 2. Group 1 models display closely spaced horse blocks. Shortening in the horse blocks is accommodated mainly by box folding and they generate fewer backthrusts than group 2 models. Group 2 models develop large spacing between the horse blocks and show structural highs bordered by both forethrusts and backthrusts. The horses are persistent along strike direction. Group 1 models are higher and possess higher structural taper than the group 2 models. In both the models, it is observed that, once a new structure forms, deformation cease to act in the old structure and it is structurally abandoned. Results of these physical models therefore demonstrate very well that the deformation rate and the decollement rheology are the key factors in controlling the structural style of a fold thrust belt. Comparing the modelling results with the published seismic section of the NFTB, it becomes very clear that structures observed in the models of group 2, i.e. those models deformed at slow strain rates, are very close to the deformation structures observed in the NFTB. The seismic section shows a basal decollement forming a low angle thrust that reaches up to the surface. Thrust horses are separated by broad synclines. Furthermore, the data reveal the buried nature of the thrust front with a triangle zone geometry. This observation is in agreement with the results of the group 2 models, which show development of dominantly forward imbricate thrust sequence. Obviously, the deformation evolution and structural features of the NFTB is governed by its weak substrata deforming under slow strain rate resulting in the generation of imbricate thrust zone.

Numerical modeling of the Indo-Australian intraplate deformation

NASA Astrophysics Data System (ADS)

Brandon, Vincent; Royer, Jean-Yves

2014-05-01

The Indo-Australian plate is perhaps the best example of wide intraplate deformation within an oceanic plate. The deformation is expressed by an unusual level of intraplate seismicity, including magnitude Mw > 8 events, large-scale folding and deep faulting of the oceanic lithosphere and reactivation of extinct fracture zones. The deformation pattern and kinematic data inversions suggest that the Indo-Australian plate can be viewed as a composite plate made of three rigid component plates - India, Capricorn, Australia - separated by wide and diffuse boundaries undergoing either extensional or compressional deformation. We tested this model using the SHELLS numerical code (Kong & Bird, 1995). The Indo-Australian plate is modeled by a mesh of 5281 spherical triangular finite elements. Mesh edges parallel the major extinct fracture zones so that they can be reactivated by reducing their friction rates. Strength of the plate is defined by the age of the lithosphere and seafloor topography. Model boundary conditions are only defined by the plate velocities predicted by the rotation vectors between rigid components of the Indo-Australian plate and their neighboring plates. Since the mesh limits all belong to rigid plates with fully defined Euler vectors, no conditions are imposed on the location, extent and limits of the diffuse and deforming zones. Using MORVEL plate velocities (DeMets et al., 2010), predicted deformation patterns are very consistent with that observed. Pre-existing structures of the lithosphere play an important role in the intraplate deformation and its distribution. The Chagos Bank focuses most of the extensional deformation between the Indian and Capricorn plates. Agreement between models and observation improves by weakening fossil fracture zones relative to the surrounding crust; however only limited sections of FZ's accommodate deformation. The reactivation of the Eocene FZ's in the Central Indian Basin (CIB) and Wharton Basin (WB) explains the drastic change in the deformation style between these basins across the Ninetyeast ridge. The highest slip rates along the WB FZ's are predicted where two major strike-slip faulting earthquakes occurred in April 2012 (Mw=8.6 and 8.2). The best model is obtained when adding a local HF anomaly in the center of the CIB (proxy for weakening the lithospheric strength), consistent with evidence of mantle serpentinization in the CIB where deep seismics image a series of N-S dipping thrust faults reaching Moho depths. The rates of extension or shortening, inferred from the predicted strain rates, are consistent with previous estimates based on different approaches. This finite element modeling confirms that oceanic lithosphere, like the continental lithosphere, can slowly deform over very broad areas (> 1000 x 1000 km).

A Physics Based Vehicle Terrain Interaction Model for Soft Soil off-Road Vehicle Simulations

DTIC Science & Technology

2012-01-01

assumed terrain deformation, use of empirical relationships for the deformation, or finite/discrete element approaches for the terrain. A real-time...vertical columns of soil, and the deformation of each is modeled using visco-elasto-plastic compressibility relationships that relate subsoil pressures to...produced by tractive and turning forces will also be incorporated into the model. Both the vertical and horizontal force/displacement relationships

Study on the Strain Hardening Behaviors of TWIP/TRIP Steels

NASA Astrophysics Data System (ADS)

Huang, T. T.; Dan, W. J.; Zhang, W. G.

2017-10-01

Due to the complex coupling of twinning-induced plasticity (TWIP), transformation-induced plasticity (TRIP), and dislocation glide in TWIP/TRIP steels, it is difficult as well as essential to build a comprehensive strain hardening model to describe the interactions between different deformation mechanisms ( i.e., deformation twinning, martensitic transformation, and dislocation glide) and the resulted strain hardening behaviors. To address this issue, a micromechanical model is established in this paper to predict the deformation process of TWIP/TRIP steels considering both TWIP and TRIP effects. In the proposed model, the generation of deformation twinning and martensitic transformation is controlled by the stacking fault energy (SFE) of the material. In the thermodynamic calculation of SFE, deformation temperature, chemical compositions, microstrain, and temperature rise during deformation are taken into account. Varied by experimental results, the developed model can predict the stress-strain response and strain hardening behaviors of TWIP/TRIP steels precisely. In addition, the improved strength and enhanced strain hardening in Fe-Mn-C TWIP/TRIP steels due to the increased carbon content is also analyzed, which consists with literature.

Modeling Dynamic Helium Release as a Tracer of Rock Deformation

DOE PAGES

Gardner, W. Payton; Bauer, Stephen J.; Kuhlman, Kristopher L.; ...

2017-11-03

Here, we use helium released during mechanical deformation of shales as a signal to explore the effects of deformation and failure on material transport properties. A dynamic dual-permeability model with evolving pore and fracture networks is used to simulate gases released from shale during deformation and failure. Changes in material properties required to reproduce experimentally observed gas signals are explored. We model two different experiments of 4He flow rate measured from shale undergoing mechanical deformation, a core parallel to bedding and a core perpendicular to bedding. We also found that the helium signal is sensitive to fracture development and evolutionmore » as well as changes in the matrix transport properties. We constrain the timing and effective fracture aperture, as well as the increase in matrix porosity and permeability. Increases in matrix permeability are required to explain gas flow prior to macroscopic failure, and the short-term gas flow postfailure. Increased matrix porosity is required to match the long-term, postfailure gas flow. This model provides the first quantitative interpretation of helium release as a result of mechanical deformation. The sensitivity of this model to changes in the fracture network, as well as to matrix properties during deformation, indicates that helium release can be used as a quantitative tool to evaluate the state of stress and strain in earth materials.« less

Real-time deformations of organ based on structural mechanics for surgical simulators

NASA Astrophysics Data System (ADS)

Nakaguchi, Toshiya; Tagaya, Masashi; Tamura, Nobuhiko; Tsumura, Norimichi; Miyake, Yoichi

2006-03-01

This research proposes the deformation model of organs for the development of the medical training system using Virtual Reality (VR) technology. First, the proposed model calculates the strains of coordinate axis. Secondly, the deformation is obtained by mapping the coordinate of the object to the strained coordinate. We assume the beams in the coordinate space to calculate the strain of the coordinate axis. The forces acting on the object are converted to the forces applied to the beams. The bend and the twist of the beams are calculated based on the theory of structural mechanics. The bend is derived by the finite element method. We propose two deformation methods which differ in the position of the beams in the coordinate space. One method locates the beams along the three orthogonal axes (x, y, z). Another method locates the beam in the area where the deformation is large. In addition, the strain of the coordinate axis is attenuated in proportion to the distance from the point of action to consider the attenuation of the stress which is a viscoelastic feature of the organs. The proposed model needs less computational cost compared to the conventional deformation method since our model does not need to divide the object into the elasticity element. The proposed model was implemented in the laparoscopic surgery training system, and a real-time deformation can be realized.

Modeling Dynamic Helium Release as a Tracer of Rock Deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gardner, W. Payton; Bauer, Stephen J.; Kuhlman, Kristopher L.

Here, we use helium released during mechanical deformation of shales as a signal to explore the effects of deformation and failure on material transport properties. A dynamic dual-permeability model with evolving pore and fracture networks is used to simulate gases released from shale during deformation and failure. Changes in material properties required to reproduce experimentally observed gas signals are explored. We model two different experiments of 4He flow rate measured from shale undergoing mechanical deformation, a core parallel to bedding and a core perpendicular to bedding. We also found that the helium signal is sensitive to fracture development and evolutionmore » as well as changes in the matrix transport properties. We constrain the timing and effective fracture aperture, as well as the increase in matrix porosity and permeability. Increases in matrix permeability are required to explain gas flow prior to macroscopic failure, and the short-term gas flow postfailure. Increased matrix porosity is required to match the long-term, postfailure gas flow. This model provides the first quantitative interpretation of helium release as a result of mechanical deformation. The sensitivity of this model to changes in the fracture network, as well as to matrix properties during deformation, indicates that helium release can be used as a quantitative tool to evaluate the state of stress and strain in earth materials.« less

Volume and tissue composition preserving deformation of breast CT images to simulate breast compression in mammographic imaging

NASA Astrophysics Data System (ADS)

Han, Tao; Chen, Lingyun; Lai, Chao-Jen; Liu, Xinming; Shen, Youtao; Zhong, Yuncheng; Ge, Shuaiping; Yi, Ying; Wang, Tianpeng; Shaw, Chris C.

2009-02-01

Images of mastectomy breast specimens have been acquired with a bench top experimental Cone beam CT (CBCT) system. The resulting images have been segmented to model an uncompressed breast for simulation of various CBCT techniques. To further simulate conventional or tomosynthesis mammographic imaging for comparison with the CBCT technique, a deformation technique was developed to convert the CT data for an uncompressed breast to a compressed breast without altering the breast volume or regional breast density. With this technique, 3D breast deformation is separated into two 2D deformations in coronal and axial views. To preserve the total breast volume and regional tissue composition, each 2D deformation step was achieved by altering the square pixels into rectangular ones with the pixel areas unchanged and resampling with the original square pixels using bilinear interpolation. The compression was modeled by first stretching the breast in the superior-inferior direction in the coronal view. The image data were first deformed by distorting the voxels with a uniform distortion ratio. These deformed data were then deformed again using distortion ratios varying with the breast thickness and re-sampled. The deformation procedures were applied in the axial view to stretch the breast in the chest wall to nipple direction while shrinking it in the mediolateral to lateral direction re-sampled and converted into data for uniform cubic voxels. Threshold segmentation was applied to the final deformed image data to obtain the 3D compressed breast model. Our results show that the original segmented CBCT image data were successfully converted into those for a compressed breast with the same volume and regional density preserved. Using this compressed breast model, conventional and tomosynthesis mammograms were simulated for comparison with CBCT.

Homogeneous Yang-Baxter deformations as generalized diffeomorphisms

NASA Astrophysics Data System (ADS)

Sakamoto, Jun-ichi; Sakatani, Yuho; Yoshida, Kentaroh

2017-10-01

Yang-Baxter (YB) deformations of string sigma model provide deformed target spaces. We propose that homogeneous YB deformations always lead to a certain class of β-twisted backgrounds and represent the bosonic part of the supergravity fields in terms of the classical r-matrix associated with the YB deformation. We then show that various β-twisted backgrounds can be realized by considering generalized diffeomorphisms in the undeformed background. Our result extends the notable relation between the YB deformations and (non-commuting) TsT transformations. We also discuss more general deformations beyond the YB deformations.

Virtual Deformation Control of the X-56A Model with Simulated Fiber Optic Sensors

NASA Technical Reports Server (NTRS)

Suh, Peter M.; Chin, Alexander W.; Mavris, Dimitri N.

2014-01-01

A robust control law design methodology is presented to stabilize the X-56A model and command its wing shape. The X-56A was purposely designed to experience flutter modes in its flight envelope. The methodology introduces three phases: the controller design phase, the modal filter design phase, and the reference signal design phase. A mu-optimal controller is designed and made robust to speed and parameter variations. A conversion technique is presented for generating sensor strain modes from sensor deformation mode shapes. The sensor modes are utilized for modal filtering and simulating fiber optic sensors for feedback to the controller. To generate appropriate virtual deformation reference signals, rigid-body corrections are introduced to the deformation mode shapes. After successful completion of the phases, virtual deformation control is demonstrated. The wing is deformed and it is shown that angle-ofattack changes occur which could potentially be used to an advantage. The X-56A program must demonstrate active flutter suppression. It is shown that the virtual deformation controller can achieve active flutter suppression on the X-56A simulation model.

Virtual Deformation Control of the X-56A Model with Simulated Fiber Optic Sensors

NASA Technical Reports Server (NTRS)

Suh, Peter M.; Chin, Alexander Wong

2013-01-01

A robust control law design methodology is presented to stabilize the X-56A model and command its wing shape. The X-56A was purposely designed to experience flutter modes in its flight envelope. The methodology introduces three phases: the controller design phase, the modal filter design phase, and the reference signal design phase. A mu-optimal controller is designed and made robust to speed and parameter variations. A conversion technique is presented for generating sensor strain modes from sensor deformation mode shapes. The sensor modes are utilized for modal filtering and simulating fiber optic sensors for feedback to the controller. To generate appropriate virtual deformation reference signals, rigid-body corrections are introduced to the deformation mode shapes. After successful completion of the phases, virtual deformation control is demonstrated. The wing is deformed and it is shown that angle-of-attack changes occur which could potentially be used to an advantage. The X-56A program must demonstrate active flutter suppression. It is shown that the virtual deformation controller can achieve active flutter suppression on the X-56A simulation model.

A revised dislocation model of interseismic deformation of the Cascadia subduction zone

USGS Publications Warehouse

Wang, Kelin; Wells, Ray E.; Mazzotti, Stephane; Hyndman, Roy D.; Sagiya, Takeshi

2003-01-01

CAS3D‐2, a new three‐dimensional (3‐D) dislocation model, is developed to model interseismic deformation rates at the Cascadia subduction zone. The model is considered a snapshot description of the deformation field that changes with time. The effect of northward secular motion of the central and southern Cascadia forearc sliver is subtracted to obtain the effective convergence between the subducting plate and the forearc. Horizontal deformation data, including strain rates and surface velocities from Global Positioning System (GPS) measurements, provide primary geodetic constraints, but uplift rate data from tide gauges and leveling also provide important validations for the model. A locked zone, based on the results of previous thermal models constrained by heat flow observations, is located entirely offshore beneath the continental slope. Similar to previous dislocation models, an effective zone of downdip transition from locking to full slip is used, but the slip deficit rate is assumed to decrease exponentially with downdip distance. The exponential function resolves the problem of overpredicting coastal GPS velocities and underpredicting inland velocities by previous models that used a linear downdip transition. A wide effective transition zone (ETZ) partially accounts for stress relaxation in the mantle wedge that cannot be simulated by the elastic model. The pattern of coseismic deformation is expected to be different from that of interseismic deformation at present, 300 years after the last great subduction earthquake. The downdip transition from full rupture to no slip should take place over a much narrower zone.

Material Properties from Air Puff Corneal Deformation by Numerical Simulations on Model Corneas

PubMed Central

Dorronsoro, Carlos; de la Hoz, Andrés; Marcos, Susana

2016-01-01

Objective To validate a new method for reconstructing corneal biomechanical properties from air puff corneal deformation images using hydrogel polymer model corneas and porcine corneas. Methods Air puff deformation imaging was performed on model eyes with artificial corneas made out of three different hydrogel materials with three different thicknesses and on porcine eyes, at constant intraocular pressure of 15 mmHg. The cornea air puff deformation was modeled using finite elements, and hyperelastic material parameters were determined through inverse modeling, minimizing the difference between the simulated and the measured central deformation amplitude and central-peripheral deformation ratio parameters. Uniaxial tensile tests were performed on the model cornea materials as well as on corneal strips, and the results were compared to stress-strain simulations assuming the reconstructed material parameters. Results The measured and simulated spatial and temporal profiles of the air puff deformation tests were in good agreement (< 7% average discrepancy). The simulated stress-strain curves of the studied hydrogel corneal materials fitted well the experimental stress-strain curves from uniaxial extensiometry, particularly in the 0–0.4 range. Equivalent Young´s moduli of the reconstructed material properties from air-puff were 0.31, 0.58 and 0.48 MPa for the three polymer materials respectively which differed < 1% from those obtained from extensiometry. The simulations of the same material but different thickness resulted in similar reconstructed material properties. The air-puff reconstructed average equivalent Young´s modulus of the porcine corneas was 1.3 MPa, within 18% of that obtained from extensiometry. Conclusions Air puff corneal deformation imaging with inverse finite element modeling can retrieve material properties of model hydrogel polymer corneas and real corneas, which are in good correspondence with those obtained from uniaxial extensiometry, suggesting that this is a promising technique to retrieve quantitative corneal biomechanical properties. PMID:27792759

The distribution of deformation in parallel fault-related folds with migrating axial surfaces: comparison between fault-propagation and fault-bend folding

NASA Astrophysics Data System (ADS)

Salvini, Francesco; Storti, Fabrizio

2001-01-01

In fault-related folds that form by axial surface migration, rocks undergo deformation as they pass through axial surfaces. The distribution and intensity of deformation in these structures has been impacted by the history of axial surface migration. Upon fold initiation, unique dip panels develop, each with a characteristic deformation intensity, depending on their history. During fold growth, rocks that pass through axial surfaces are transported between dip panels and accumulate additional deformation. By tracking the pattern of axial surface migration in model folds, we predict the distribution of relative deformation intensity in simple-step, parallel fault-bend and fault-propagation anticlines. In both cases the deformation is partitioned into unique domains we call deformation panels. For a given rheology of the folded multilayer, deformation intensity will be homogeneously distributed in each deformation panel. Fold limbs are always deformed. The flat crests of fault-propagation anticlines are always undeformed. Two asymmetric deformation panels develop in fault-propagation folds above ramp angles exceeding 29°. For lower ramp angles, an additional, more intensely-deformed panel develops at the transition between the crest and the forelimb. Deformation in the flat crests of fault-bend anticlines occurs when fault displacement exceeds the length of the footwall ramp, but is never found immediately hinterland of the crest to forelimb transition. In environments dominated by brittle deformation, our models may serve as a first-order approximation of the distribution of fractures in fault-related folds.

Modeling and Characterization of PMMA for High Strain-Rate and Finite Deformations (Postprint)

DTIC Science & Technology

2010-05-01

List of parameters for the modified MuUiken- model for PMMA . Von Mises [MPa] ^AJ3 V 00 ^ Aa ^Afi CR ha hp Value 3386 1748 0.35 298 1979...AFRL-RW-EG-TP-2010-073 Modeling and Characterization of PMMA for High Strain-Rate and Finite Deformations (Postprint) Eric B. Herbold Jennifer L...SUBTITLE Modeling and Characterization of PMMA for High Strain-Rate and Finite Deformations (Postprint) 5a. CONTRACT NUMBER 5b. GRANT NUMBER

Reconciling postseismic and interseismic surface deformation around strike-slip faults: Earthquake-cycle models with finite ruptures and viscous shear zones

NASA Astrophysics Data System (ADS)

Hearn, E. H.

2013-12-01

Geodetic surface velocity data show that after an energetic but brief phase of postseismic deformation, surface deformation around most major strike-slip faults tends to be localized and stationary, and can be modeled with a buried elastic dislocation creeping at or near the Holocene slip rate. Earthquake-cycle models incorporating an elastic layer over a Maxwell viscoelastic halfspace cannot explain this, even when the earliest postseismic deformation is ignored or modeled (e.g., as frictional afterslip). Models with heterogeneously distributed low-viscosity materials or power-law rheologies perform better, but to explain all phases of earthquake-cycle deformation, Burgers viscoelastic materials with extreme differences between their Maxwell and Kelvin element viscosities seem to be required. I present a suite of earthquake-cycle models to show that postseismic and interseismic deformation may be reconciled for a range of lithosphere architectures and rheologies if finite rupture length is taken into account. These models incorporate high-viscosity lithosphere optionally cut by a viscous shear zone, and a lower-viscosity mantle asthenosphere (all with a range of viscoelastic rheologies and parameters). Characteristic earthquakes with Mw = 7.0 - 7.9 are investigated, with interseismic intervals adjusted to maintain the same slip rate (10, 20 or 40 mm/yr). I find that a high-viscosity lower crust/uppermost mantle (or a high viscosity per unit width viscous shear zone at these depths) is required for localized and stationary interseismic deformation. For Mw = 7.9 characteristic earthquakes, the shear zone viscosity per unit width in the lower crust and uppermost mantle must exceed about 10^16 Pa s /m. For a layered viscoelastic model the lower crust and uppermost mantle effective viscosity must exceed about 10^20 Pa s. The range of admissible shear zone and lower lithosphere rheologies broadens considerably for faults producing more frequent but smaller characteristic earthquakes. Thus, minimum lithosphere or shear zone effective viscosities inferred from interseismic GPS data and infinite-fault earthquake-cycle models may be too high. The finite-fault models show that relaxation of viscoelastic material in the mid crust (most likely along a viscous shear zone) may be consistent with near- to intermediate-field postseismic deformation typical of recent Mw = 7.4 to 7.9 earthquakes. This deformation is compatible with more localized and time-invariant deformation during most of the interseismic interval if (1) shear zone viscosity per unit width increases with depth or (2) the shear zone material has a Burgers viscoelastic rheology.

A reduced-order, single-bubble cavitation model with applications to therapeutic ultrasound

PubMed Central

Kreider, Wayne; Crum, Lawrence A.; Bailey, Michael R.; Sapozhnikov, Oleg A.

2011-01-01

Cavitation often occurs in therapeutic applications of medical ultrasound such as shock-wave lithotripsy (SWL) and high-intensity focused ultrasound (HIFU). Because cavitation bubbles can affect an intended treatment, it is important to understand the dynamics of bubbles in this context. The relevant context includes very high acoustic pressures and frequencies as well as elevated temperatures. Relative to much of the prior research on cavitation and bubble dynamics, such conditions are unique. To address the relevant physics, a reduced-order model of a single, spherical bubble is proposed that incorporates phase change at the liquid-gas interface as well as heat and mass transport in both phases. Based on the energy lost during the inertial collapse and rebound of a millimeter-sized bubble, experimental observations were used to tune and test model predictions. In addition, benchmarks from the published literature were used to assess various aspects of model performance. Benchmark comparisons demonstrate that the model captures the basic physics of phase change and diffusive transport, while it is quantitatively sensitive to specific model assumptions and implementation details. Given its performance and numerical stability, the model can be used to explore bubble behaviors across a broad parameter space relevant to therapeutic ultrasound. PMID:22088026

A reduced-order, single-bubble cavitation model with applications to therapeutic ultrasound.

PubMed

Kreider, Wayne; Crum, Lawrence A; Bailey, Michael R; Sapozhnikov, Oleg A

2011-11-01

Cavitation often occurs in therapeutic applications of medical ultrasound such as shock-wave lithotripsy (SWL) and high-intensity focused ultrasound (HIFU). Because cavitation bubbles can affect an intended treatment, it is important to understand the dynamics of bubbles in this context. The relevant context includes very high acoustic pressures and frequencies as well as elevated temperatures. Relative to much of the prior research on cavitation and bubble dynamics, such conditions are unique. To address the relevant physics, a reduced-order model of a single, spherical bubble is proposed that incorporates phase change at the liquid-gas interface as well as heat and mass transport in both phases. Based on the energy lost during the inertial collapse and rebound of a millimeter-sized bubble, experimental observations were used to tune and test model predictions. In addition, benchmarks from the published literature were used to assess various aspects of model performance. Benchmark comparisons demonstrate that the model captures the basic physics of phase change and diffusive transport, while it is quantitatively sensitive to specific model assumptions and implementation details. Given its performance and numerical stability, the model can be used to explore bubble behaviors across a broad parameter space relevant to therapeutic ultrasound.

An efficient and scalable deformable model for virtual reality-based medical applications.

PubMed

Choi, Kup-Sze; Sun, Hanqiu; Heng, Pheng-Ann

2004-09-01

Modeling of tissue deformation is of great importance to virtual reality (VR)-based medical simulations. Considerable effort has been dedicated to the development of interactively deformable virtual tissues. In this paper, an efficient and scalable deformable model is presented for virtual-reality-based medical applications. It considers deformation as a localized force transmittal process which is governed by algorithms based on breadth-first search (BFS). The computational speed is scalable to facilitate real-time interaction by adjusting the penetration depth. Simulated annealing (SA) algorithms are developed to optimize the model parameters by using the reference data generated with the linear static finite element method (FEM). The mechanical behavior and timing performance of the model have been evaluated. The model has been applied to simulate the typical behavior of living tissues and anisotropic materials. Integration with a haptic device has also been achieved on a generic personal computer (PC) platform. The proposed technique provides a feasible solution for VR-based medical simulations and has the potential for multi-user collaborative work in virtual environment.

Tectonic evolution of the Arizaro basin of the Puna plateau, NW Argentina: Implications for plateau-scale processes

NASA Astrophysics Data System (ADS)

Boyd, John D.

Sedimentary basins of the Altiplano-Puna Plateau within the Andean Plateau in South America contain the record of retro-arc foreland basin evolution during the Cenozoic. The deformation of these basins is characterized by high angle reverse faults and thrusts deforming crystalline basement and sedimentary covers. The mechanism/s responsible for deformation within the region are not fully understood in detail. The relative abundance of intercalated tuffs within these basins and those within the bounding Eastern Cordillera enables the spatial-temporal pattern of deformation across the orogen to be constrained. This study uses the systematic combination of structural, geochronologic and sedimentalogical techniques applied to Cenozoic sedimentary rocks within the Arizaro Basin to investigate the timing of deformation across within the region in order to test two end member models for basin deformation in response to lithospheric processes. The first model attributes the deformation of the basins to internal deformation within an orogenic wedge as part of the taper building process required prior to propagation eastward towards the foreland basin system. The second model attributes basin deformation to isostatic adjustments resulting from small-scale lithospheric foundering. Detailed geologic mapping of the Arizaro Basin reveals a complex interplay of coeval thick-skinned and thin-skinned deformation, which deforms the thick Miocene succession of fluvial-lacustrine strata in both a brittle and ductile manner. Zircon U-Pb analyses of intercalated tuffs from the Vizcachera Formation reveal that approximately three km of the section was deposited between the Early Miocene (ca. 18.3) and the Middle Miocene (ca. 13.9). One tuff in the uppermost Vizcachera Formation constrains the lower limit of timing of deformation for the Arizaro Basin to be 13.9 +/- 0.7 Ma. When combined with published geochronological data across the Puna Plateau and Eastern Cordillera, the new data presented in this study constrains timing of deformation within the basin and the greater Arizaro area to the Middle Miocene. This study also indicates that the spatial-temporal patterns of deformation are likely the result of a combination of both models mentioned above with critical taper theory dominating early deformation associated with basin formation and small-scale lithospheric foundering dominating the later deformation in the Middle Miocene. Deformation at the wedge tip continues in the Eastern Cordillera seemingly without interruption, suggesting that the effects of the isostatic pull-down associated with small-scale lithospheric foundering is localized and does not significantly affect the taper of the orogenic wedge as a whole. Thus, allowing the normal cycle of orogenic wedge propagation to occur, uninhibited.

Adapting Reference for a Unique Group of Distance Learners: Serving the American Institute of Certified Public Accountants (AICPA)

ERIC Educational Resources Information Center

Martin, Maria Mathilde

2004-01-01

When a university acquires the library of a national institute and the institute's active and worldwide membership expects continued and uninterrupted access to services from the collection, shockwaves can reverberate throughout the university's main library and among its staff. This was especially true for the Reference Department of the…

The Structure of a Hypersonic Air Flow near a Plane Surface at Various Intensities of Magnetogasdynamic Interaction

NASA Astrophysics Data System (ADS)

Fomichev, V. P.; Yadrenkin, M. A.

2017-12-01

This Letter presents a systematization of the effects observed in experiments on the magnetogasdynamic interaction near the surface of a plate in a high-speed gas flow. Ranges of the hydromagnetic-interaction parameter determining various levels of influence on the shock-wave structure of the flow are established.

Assessing Homegrown Library Collections: Using Google Analytics to Track Use of Screencasts and Flash-Based Learning Objects

ERIC Educational Resources Information Center

Betty, Paul

2009-01-01

Increasing use of screencast and Flash authoring software within libraries is resulting in "homegrown" library collections of digital learning objects and multimedia presentations. The author explores the use of Google Analytics to track usage statistics for interactive Shockwave Flash (.swf) files, the common file output for screencast and Flash…

Career Guidance in Unstable Times: Linking Economic, Social and Individual Benefits. Briefing Note

ERIC Educational Resources Information Center

Cedefop - European Centre for the Development of Vocational Training, 2014

2014-01-01

The economic crisis that peaked in 2009 sent shockwaves that will be felt for years to come. It affected businesses, increased social risk for many and destabilised job and career prospects. Young people, particularly, have been badly affected. They are suffering the highest unemployment rates and their prospects have been damaged most. But,…

Plasma discharge self-cleaning filtration system

DOEpatents

Cho, Young I.; Fridman, Alexander; Gutsol, Alexander F.; Yang, Yong

2014-07-22

The present invention is directed to a novel method for cleaning a filter surface using a plasma discharge self-cleaning filtration system. The method involves utilizing plasma discharges to induce short electric pulses of nanoseconds duration at high voltages. These electrical pulses generate strong Shockwaves that disintegrate and dislodge particulate matter located on the surface of the filter.

Experimental Research on the Elastic Deformation Mode of S235JR Rolled Steel Fastened between the Centers of a Universal Lathe

NASA Astrophysics Data System (ADS)

Tabacaru, LL; Axinte, E.; Musca, G.

2016-11-01

Elastic deformations of the technological system occur during the mechanical treatment of a blank, regardless of the manner in which it is fastened. The elastic deformation of the blank is significant especially when machining shaft-like parts. The purpose of our research is to compare the mathematical model of blank deformation to the experimental model when the blank, which is a part belonging to the shaft class, is fastened between centers.

Response of explosive HMX to low-velocity impact: modeling by the crystal plasticity finite element method

NASA Astrophysics Data System (ADS)

Ilnitsky, Denis; Inogamov, Nail; Zhakhovsky, Vasily

2017-12-01

Crystal plasticity finite element method (CPFEM) is a powerful tool for modeling the various deformation problems, which takes into account the different plasticity mechanisms at microscale of grain sizes and contribution of anisotropic behavior of each grain to macroscopic deformation pattern. Using this method we simulated deformation and plasticity of high explosive HMX produced by relatively low velocity impact. It was found that such plastic deformations of grains cause local heating which is sufficient to induce chemical reactions.

Bridge Structure Deformation Prediction Based on GNSS Data Using Kalman-ARIMA-GARCH Model

PubMed Central

Li, Xiaoqing; Wang, Yu

2018-01-01

Bridges are an essential part of the ground transportation system. Health monitoring is fundamentally important for the safety and service life of bridges. A large amount of structural information is obtained from various sensors using sensing technology, and the data processing has become a challenging issue. To improve the prediction accuracy of bridge structure deformation based on data mining and to accurately evaluate the time-varying characteristics of bridge structure performance evolution, this paper proposes a new method for bridge structure deformation prediction, which integrates the Kalman filter, autoregressive integrated moving average model (ARIMA), and generalized autoregressive conditional heteroskedasticity (GARCH). Firstly, the raw deformation data is directly pre-processed using the Kalman filter to reduce the noise. After that, the linear recursive ARIMA model is established to analyze and predict the structure deformation. Finally, the nonlinear recursive GARCH model is introduced to further improve the accuracy of the prediction. Simulation results based on measured sensor data from the Global Navigation Satellite System (GNSS) deformation monitoring system demonstrated that: (1) the Kalman filter is capable of denoising the bridge deformation monitoring data; (2) the prediction accuracy of the proposed Kalman-ARIMA-GARCH model is satisfactory, where the mean absolute error increases only from 3.402 mm to 5.847 mm with the increment of the prediction step; and (3) in comparision to the Kalman-ARIMA model, the Kalman-ARIMA-GARCH model results in superior prediction accuracy as it includes partial nonlinear characteristics (heteroscedasticity); the mean absolute error of five-step prediction using the proposed model is improved by 10.12%. This paper provides a new way for structural behavior prediction based on data processing, which can lay a foundation for the early warning of bridge health monitoring system based on sensor data using sensing technology. PMID:29351254

Bridge Structure Deformation Prediction Based on GNSS Data Using Kalman-ARIMA-GARCH Model.

PubMed

Xin, Jingzhou; Zhou, Jianting; Yang, Simon X; Li, Xiaoqing; Wang, Yu

2018-01-19

Bridges are an essential part of the ground transportation system. Health monitoring is fundamentally important for the safety and service life of bridges. A large amount of structural information is obtained from various sensors using sensing technology, and the data processing has become a challenging issue. To improve the prediction accuracy of bridge structure deformation based on data mining and to accurately evaluate the time-varying characteristics of bridge structure performance evolution, this paper proposes a new method for bridge structure deformation prediction, which integrates the Kalman filter, autoregressive integrated moving average model (ARIMA), and generalized autoregressive conditional heteroskedasticity (GARCH). Firstly, the raw deformation data is directly pre-processed using the Kalman filter to reduce the noise. After that, the linear recursive ARIMA model is established to analyze and predict the structure deformation. Finally, the nonlinear recursive GARCH model is introduced to further improve the accuracy of the prediction. Simulation results based on measured sensor data from the Global Navigation Satellite System (GNSS) deformation monitoring system demonstrated that: (1) the Kalman filter is capable of denoising the bridge deformation monitoring data; (2) the prediction accuracy of the proposed Kalman-ARIMA-GARCH model is satisfactory, where the mean absolute error increases only from 3.402 mm to 5.847 mm with the increment of the prediction step; and (3) in comparision to the Kalman-ARIMA model, the Kalman-ARIMA-GARCH model results in superior prediction accuracy as it includes partial nonlinear characteristics (heteroscedasticity); the mean absolute error of five-step prediction using the proposed model is improved by 10.12%. This paper provides a new way for structural behavior prediction based on data processing, which can lay a foundation for the early warning of bridge health monitoring system based on sensor data using sensing technology.

Numerical investigations on aerodynamic forces of deformable foils in hovering motions

NASA Astrophysics Data System (ADS)

Su, Xiaohui; Yin, Zhen; Cao, Yuanwei; Zhao, Yong

2017-04-01

In this paper, the aerodynamic forces of deformable foils for hovering flight are numerically investigated by a two-dimensional finite-volume arbitrary Lagrangian Eulerian Navier-Stokes solver. The effects of deformation on the lift force generation mechanisms of deformable wings in hovering flight are studied by comparison and analysis of deformable and rigid wing results. The prescribed deformation of the wings changes their morphing during hovering motion in both camber and angle of incidence. The effects of deflection amplitude, deflection phase, and rotation location on the aerodynamic performances of the foils, as well as the associated flow structures, are investigated in details, respectively. Results obtained show that foil morphing changes both Leading Edge Vortex (LEV) and Trailing Edge Vortex (TEV) generation and development processes. Consequently, the lift force generation mechanisms of deformable wings differ from those of rigid foil models. For the full deformation foil model studied, the effect of foil deformation enhances its lift force during both wake capture and delayed stall. There is an optimized camber amplitude, which was found to be 0.1*chord among those cases simulated. Partial deformation in the foil does not enhance its lift force due to unfavorable foil camber. TEV is significantly changed by the local angle of attack due to the foil deformation. On the other hand, Trailing Edge Flap (TEF) deflection in the hinge connected two-rigid-plate model directly affects the strength of both the LEV and TEV, thus influencing the entire vortex shedding process. It was found that lift enhancement can reach up to 33.5% just by the TEF deflection alone.

Simplification of the laser absorption process in the particle simulation for the laser-induced shockwave processing

NASA Astrophysics Data System (ADS)

Shimamura, Kohei

2016-09-01

To reduce the computational cost in the particle method for the numerical simulation of the laser plasma, we examined the simplification of the laser absorption process. Because the laser frequency is sufficiently larger than the collision frequency between the electron and heavy particles, we assumed that the electron obtained the constant value from the laser irradiation. First of all, the simplification of the laser absorption process was verified by the comparison of the EEDF and the laser-absorptivity with PIC-FDTD method. Secondary, the laser plasma induced by TEA CO2 laser in Argon atmosphere was modeled using the 1D3V DSMC method with the simplification of the laser-absorption. As a result, the LSDW was observed with the typical electron and neutral density distribution.

Geomechanical Modeling of Deformation Banding in the Navajo Sandstone, San Rafael Monocline, Utah

NASA Astrophysics Data System (ADS)

Gutierrez, M.; Sundal, A.; Petrie, E. S.

2017-12-01

Deformation bands are ubiquitous geological features in many types of rocks. Depending on their micro-structure, they can act either as conduits or barriers to fluid flow. Given the significant roles deformation bands play in fluid flow and chemical transport in rocks, it is important to develop fundamental understanding of their origin, and their characteristics as they relate with the host rock properties and their depositional and structural-geological history. We present a forward-modeling technique based on the geomechanical Bifurcation Theory (BT) to predict the formation of deformation bands in sandstone. According to BT, the formation of deformation bands is a result of strain location, which in turn stems from instability in the stress-strain response of materials during loading. Due to bifurcation, a material which undergoes homogeneous deformation can reach a point at which the material experiences instability and deformation starts to become non-homogenous. We implemented BT in the commercially-available geomechanical code FLAC (Fast Langragian Analysis of Continua) and applied it in the field-scale modeling of deformation banding in the Navajo Sandstone in the San Rafael Monocline in Utah induced by fault propagation folding. The results show that geomechanical modeling using BT has a powerful potential to simulate the physical processes in the formation of deformation banding in rocks. Predicted deformation bands, specifically the pervasive bedding-parallel bands in the Navajo sandstone formation, normal faulting in the upper limb and reverse faulting in the lower limb, are generally in agreement with field observations. Predictions indicate that the pervasive bedding-parallel bands in the Navajo Sandstone are transitional compaction-shear bands with alternating zones of volumetric compaction and dilation. These predictions are consistent with petrographic analysis of thin sections of rock samples from the Navajo Sandstone. The most important parameter in the geomechanical modeling is the dilation angle in relation to the friction angle of the host rock. These parameters, as well the elastic properties, should evolve during the geologic history of a site, thus, the main challenge in the modeling is how to calibrate these parameters to yield consistent results.

Conceptual Model for Basement and Surface Structure Relationships in an Oblique Collision, Sawtooth Range, MT

NASA Astrophysics Data System (ADS)

Palu, J. M.; Burberry, C. M.

2014-12-01

The reactivation potential of pre-existing basement structures affects the geometry of subsequent deformation structures. A conceptual model depicting the results of these interactions can be applied to multiple fold-thrust systems and lead to valuable deformation predictions. These predictions include the potential for hydrocarbon traps or seismic risk in an actively deforming area. The Sawtooth Range, Montana, has been used as a study area. A model for the development of structures close to the Augusta Syncline in the Sawtooth Range is being developed using: 1) an ArcGIS map of the basement structures of the belt based on analysis of geophysical data indicating gravity anomalies and aeromagnetic lineations, seismic data indicating deformation structures, and well logs for establishing lithologies, previously collected by others and 2) an ArcGIS map of the surface deformation structures of the belt based on interpretation of remote sensing images and verification through the collection of surface field data indicating stress directions and age relationships, resulting in a conceptual model based on the understanding of the interaction of the two previous maps including statistical correlations of data and development of balanced cross-sections using Midland Valley's 2D/3D Move software. An analysis of the model will then indicate viable deformation paths where prominent basement structures influenced subsequently developed deformation structures and reactivated faults. Preliminary results indicate that the change in orientation of thrust faults observed in the Sawtooth Range, from a NNW-SSE orientation near the Gibson Reservoir to a WNW-ESE trend near Haystack Butte correlates with pre-existing deformation structures lying within the Great Falls Tectonic Zone. The Scapegoat-Bannatyne trend appears to be responsible for this orientation change and rather than being a single feature, may be composed of up to 4 NE-SW oriented basement strike-slip faults. This indicates that the pre-existing basement features have a profound effect on the geometry of the later deformation. This conceptual model can also be applied to other deformed belts to provide a prediction for the potential hydrocarbon trap locations of the belt as well as their seismic risk.

Half-Lives of Proton Emitters With a Deformed Density-Dependent Model

NASA Astrophysics Data System (ADS)

Qian, Yi-Bin; Ren, Zhong-Zhou; Ni, Dong-Dong; Sheng, Zong-Qiang

2010-11-01

Half-lives of proton radioactivity are investigated with a deformed density-dependent model. The single folding potential which is dependent on deformation and orientation is employed to calculate the proton decay width through the deformed potential barrier. In addition, the spectroscopic factor is taken into account in the calculation, which is obtained in the relativistic mean field theory with NL3. The calculated results of semi-spherical nuclei are found to be in good agreement with the experimental data, and the results of well-deformed nuclei are also satisfactory. Moreover, a formula for the spherical proton emission half-life based on the Gamow quantum tunneling theory is presented.

InSAR observations of low slip rates on the major faults of western Tibet.

PubMed

Wright, Tim J; Parsons, Barry; England, Philip C; Fielding, Eric J

2004-07-09

Two contrasting views of the active deformation of Asia dominate the debate about how continents deform: (i) The deformation is primarily localized on major faults separating crustal blocks or (ii) deformation is distributed throughout the continental lithosphere. In the first model, western Tibet is being extruded eastward between the major faults bounding the region. Surface displacement measurements across the western Tibetan plateau using satellite radar interferometry (InSAR) indicate that slip rates on the Karakoram and Altyn Tagh faults are lower than would be expected for the extrusion model and suggest a significant amount of internal deformation in Tibet.

A structural dynamics study of a wing-pylon-tiltrotor system

NASA Astrophysics Data System (ADS)

Khader, N.; Abu-Mallouh, R.

1992-12-01

A simple structural model for a three-bladed tiltrotor-pylon-wing assembly is presented, which accounts for chordwise, transverse, and torsional wing deformations, rigid pylon pitching motion with respect to the wing tip cross-section in its deformed position, lead-lag, flap, and torsional deformations of rotor blades. The model considers equivalent viscous damping associated with blade and wing elastic deformations and with rigid pylon pitching motion. It is established that blade-to wing bending rigidity ratio, pylon pitching frequency, equivalent viscous damping associated with blade elastic deformations, and rotational speed, are the most important design parameters, whose effect on system frequencies and stability boundaries is evaluated.

Modeling and Measurement of 3D Deformation of Scoliotic Spine Using 2D X-ray Images

NASA Astrophysics Data System (ADS)

Li, Hao; Leow, Wee Kheng; Huang, Chao-Hui; Howe, Tet Sen

Scoliosis causes deformations such as twisting and lateral bending of the spine. To correct scoliotic deformation, the extents of 3D spinal deformation need to be measured. This paper studies the modeling and measurement of scoliotic spine based on 3D curve model. Through modeling the spine as a 3D Cosserat rod, the 3D structure of a scoliotic spine can be recovered by obtaining the minimum potential energy registration of the rod to the scoliotic spine in the x-ray image. Test results show that it is possible to obtain accurate 3D reconstruction using only the landmarks in a single view, provided that appropriate boundary conditions and elastic properties are included as constraints.

Knowledge modeling in image-guided neurosurgery: application in understanding intraoperative brain shift

NASA Astrophysics Data System (ADS)

Cohen-Adad, Julien; Paul, Perrine; Morandi, Xavier; Jannin, Pierre

2006-03-01

During an image-guided neurosurgery procedure, the neuronavigation system is subject to inaccuracy because of anatomical deformations which induce a gap between the preoperative images and their anatomical reality. Thus, the objective of many research teams is to succeed in quantifying these deformations in order to update preoperative images. Anatomical intraoperative deformations correspond to a complex spatio-temporal phenomenon. Our objective is to identify the parameters implicated in these deformations and to use these parameters as constrains for systems dedicated to updating preoperative images. In order to identify these parameters of deformation we followed the iterative methodology used for cognitive system conception: identification, conceptualization, formalization, implementation and validation. A state of the art about cortical deformations has been established in order to identify relevant parameters probably involved in the deformations. As a first step, 30 parameters have been identified and described following an ontological approach. They were formalized into a Unified Modeling Language (UML) class diagram. We implemented that model into a web-based application in order to fill a database. Two surgical cases have been studied at this moment. After having entered enough surgical cases for data mining purposes, we expect to identify the most relevant and influential parameters and to gain a better ability to understand the deformation phenomenon. This original approach is part of a global system aiming at quantifying and correcting anatomical deformations.

PLATFORM DEFORMATION PHASE CORRECTION FOR THE AMiBA-13 COPLANAR INTERFEROMETER

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liao, Yu-Wei; Lin, Kai-Yang; Huang, Yau-De

2013-05-20

We present a new way to solve the platform deformation problem of coplanar interferometers. The platform of a coplanar interferometer can be deformed due to driving forces and gravity. A deformed platform will induce extra components into the geometric delay of each baseline and change the phases of observed visibilities. The reconstructed images will also be diluted due to the errors of the phases. The platform deformations of The Yuan-Tseh Lee Array for Microwave Background Anisotropy (AMiBA) were modeled based on photogrammetry data with about 20 mount pointing positions. We then used the differential optical pointing error between two opticalmore » telescopes to fit the model parameters in the entire horizontal coordinate space. With the platform deformation model, we can predict the errors of the geometric phase delays due to platform deformation with a given azimuth and elevation of the targets and calibrators. After correcting the phases of the radio point sources in the AMiBA interferometric data, we recover 50%-70% flux loss due to phase errors. This allows us to restore more than 90% of a source flux. The method outlined in this work is not only applicable to the correction of deformation for other coplanar telescopes but also to single-dish telescopes with deformation problems. This work also forms the basis of the upcoming science results of AMiBA-13.« less

Using Remote Sensing Data to Constrain Models of Fault Interactions and Plate Boundary Deformation

NASA Astrophysics Data System (ADS)

Glasscoe, M. T.; Donnellan, A.; Lyzenga, G. A.; Parker, J. W.; Milliner, C. W. D.

2016-12-01

Determining the distribution of slip and behavior of fault interactions at plate boundaries is a complex problem. Field and remotely sensed data often lack the necessary coverage to fully resolve fault behavior. However, realistic physical models may be used to more accurately characterize the complex behavior of faults constrained with observed data, such as GPS, InSAR, and SfM. These results will improve the utility of using combined models and data to estimate earthquake potential and characterize plate boundary behavior. Plate boundary faults exhibit complex behavior, with partitioned slip and distributed deformation. To investigate what fraction of slip becomes distributed deformation off major faults, we examine a model fault embedded within a damage zone of reduced elastic rigidity that narrows with depth and forward model the slip and resulting surface deformation. The fault segments and slip distributions are modeled using the JPL GeoFEST software. GeoFEST (Geophysical Finite Element Simulation Tool) is a two- and three-dimensional finite element software package for modeling solid stress and strain in geophysical and other continuum domain applications [Lyzenga, et al., 2000; Glasscoe, et al., 2004; Parker, et al., 2008, 2010]. New methods to advance geohazards research using computer simulations and remotely sensed observations for model validation are required to understand fault slip, the complex nature of fault interaction and plate boundary deformation. These models help enhance our understanding of the underlying processes, such as transient deformation and fault creep, and can aid in developing observation strategies for sUAV, airborne, and upcoming satellite missions seeking to determine how faults behave and interact and assess their associated hazard. Models will also help to characterize this behavior, which will enable improvements in hazard estimation. Validating the model results against remotely sensed observations will allow us to better constrain fault zone rheology and physical properties, having implications for the overall understanding of earthquake physics, fault interactions, plate boundary deformation and earthquake hazard, preparedness and risk reduction.

Global tectonic reconstructions with continuously deforming and evolving rigid plates

NASA Astrophysics Data System (ADS)

Gurnis, Michael; Yang, Ting; Cannon, John; Turner, Mark; Williams, Simon; Flament, Nicolas; Müller, R. Dietmar

2018-07-01

Traditional plate reconstruction methodologies do not allow for plate deformation to be considered. Here we present software to construct and visualize global tectonic reconstructions with deforming plates within the context of rigid plates. Both deforming and rigid plates are defined by continuously evolving polygons. The deforming regions are tessellated with triangular meshes such that either strain rate or cumulative strain can be followed. The finite strain history, crustal thickness and stretching factor of points within the deformation zones are tracked as Lagrangian points. Integrating these tools within the interactive platform GPlates enables specialized users to build and refine deforming plate models and integrate them with other models in time and space. We demonstrate the integrated platform with regional reconstructions of Cenozoic western North America, the Mesozoic South American Atlantic margin, and Cenozoic southeast Asia, embedded within global reconstructions, using different data and reconstruction strategies.

Ground Subsidence Monitoring with MT-InSAR and Mechanism Inversion Over Xi'an, China

NASA Astrophysics Data System (ADS)

Peng, M. M.; Zhao, C. Y.; Zhang, Q.; Zhang, J.; Liu, Y. Y.

2018-04-01

The ancient Xi'an, China, has been suffering severe land subsidence and ground fissure hazards since the 1960s, which has affected the safety of Subways. Multi-sensor SAR data are conducted to monitor the latest complex ground deformation and its influence on subway line No.3 over Xi'an. Annual deformation rates have been retrieved to reveal the spatiotemporal evolution of ground subsidence in Xi'an city from 2013 to 2017. Meanwhile, the correlation between land subsidence and ground fissures are analyzed by retrieving the deformation differences in both sides of the fissures. Besides, the deformation along subway line No. 3 is analyzed, and the fast deformation section is quantitatively studied. Finally, a flat lying sill model with distributed contractions is implemented to model the InSAR deformation over YHZ subsidence center, which manifests that the ground deformation is mainly caused by groundwater withdrawal.

Use of multiscale zirconium alloy deformation models in nuclear fuel behavior analysis

NASA Astrophysics Data System (ADS)

Montgomery, Robert; Tomé, Carlos; Liu, Wenfeng; Alankar, Alankar; Subramanian, Gopinath; Stanek, Christopher

2017-01-01

Accurate prediction of cladding mechanical behavior is a key aspect of modeling nuclear fuel behavior, especially for conditions of pellet-cladding interaction (PCI), reactivity-initiated accidents (RIA), and loss of coolant accidents (LOCA). Current approaches to fuel performance modeling rely on empirical constitutive models for cladding creep, growth and plastic deformation, which are limited to the materials and conditions for which the models were developed. To improve upon this approach, a microstructurally-based zirconium alloy mechanical deformation analysis capability is being developed within the United States Department of Energy Consortium for Advanced Simulation of Light Water Reactors (CASL). Specifically, the viscoplastic self-consistent (VPSC) polycrystal plasticity modeling approach, developed by Lebensohn and Tomé [1], has been coupled with the BISON engineering scale fuel performance code to represent the mechanistic material processes controlling the deformation behavior of light water reactor (LWR) cladding. A critical component of VPSC is the representation of the crystallographic nature (defect and dislocation movement) and orientation of the grains within the matrix material and the ability to account for the role of texture on deformation. A future goal is for VPSC to obtain information on reaction rate kinetics from atomistic calculations to inform the defect and dislocation behavior models described in VPSC. The multiscale modeling of cladding deformation mechanisms allowed by VPSC far exceed the functionality of typical semi-empirical constitutive models employed in nuclear fuel behavior codes to model irradiation growth and creep, thermal creep, or plasticity. This paper describes the implementation of an interface between VPSC and BISON and provides initial results utilizing the coupled functionality.

Numerical Simulation of Multiphase Magnetohydrodynamic Flow and Deformation of Electrolyte-Metal Interface in Aluminum Electrolysis Cells

NASA Astrophysics Data System (ADS)

Hua, Jinsong; Rudshaug, Magne; Droste, Christian; Jorgensen, Robert; Giskeodegard, Nils-Haavard

2018-06-01

A computational fluid dynamics based multiphase magnetohydrodynamic (MHD) flow model for simulating the melt flow and bath-metal interface deformation in realistic aluminum reduction cells is presented. The model accounts for the complex physics of the MHD problem in aluminum reduction cells by coupling two immiscible fluids, electromagnetic field, Lorentz force, flow turbulence, and complex cell geometry with large length scale. Especially, the deformation of bath-metal interface is tracked directly in the simulation, and the condition of constant anode-cathode distance (ACD) is maintained by moving anode bottom dynamically with the deforming bath-metal interface. The metal pad deformation and melt flow predicted by the current model are compared to the predictions using a simplified model where the bath-metal interface is assumed flat. The effects of the induced electric current due to fluid flow and the magnetic field due to the interior cell current on the metal pad deformation and melt flow are investigated. The presented model extends the conventional simplified box model by including detailed cell geometry such as the ledge profile and all channels (side, central, and cross-channels). The simulations show the model sensitivity to different side ledge profiles and the cross-channel width by comparing the predicted melt flow and metal pad heaving. In addition, the model dependencies upon the reduction cell operation conditions such as ACD, current distribution on cathode surface and open/closed channel top, are discussed.

The choice of a constitutive formulation for modeling limb flexion-induced deformations and stresses in the human femoropopliteal arteries of different ages.

PubMed

Desyatova, Anastasia; MacTaggart, Jason; Poulson, William; Deegan, Paul; Lomneth, Carol; Sandip, Anjali; Kamenskiy, Alexey

2017-06-01

Open and endovascular treatments for peripheral arterial disease are notorious for high failure rates. Severe mechanical deformations experienced by the femoropopliteal artery (FPA) during limb flexion and interactions between the artery and repair materials play important roles and may contribute to poor clinical outcomes. Computational modeling can help optimize FPA repair, but these simulations heavily depend on the choice of constitutive model describing the arterial behavior. In this study finite element model of the FPA in the standing (straight) and gardening (acutely bent) postures was built using computed tomography data, longitudinal pre-stretch and biaxially determined mechanical properties. Springs and dashpots were used to represent surrounding tissue forces associated with limb flexion-induced deformations. These forces were then used with age-specific longitudinal pre-stretch and mechanical properties to obtain deformed FPA configurations for seven age groups. Four commonly used invariant-based constitutive models were compared to determine the accuracy of capturing deformations and stresses in each age group. The four-fiber FPA model most accurately portrayed arterial behavior in all ages, but in subjects younger than 40 years, the performance of all constitutive formulations was similar. In older subjects, Demiray (Delfino) and classic two-fiber Holzapfel-Gasser-Ogden formulations were better than the Neo-Hookean model for predicting deformations due to limb flexion, but both significantly overestimated principal stresses compared to the FPA or Neo-Hookean models.

Study of phase transition of even and odd nuclei based on q-deforme SU(1,1) algebraic model

NASA Astrophysics Data System (ADS)

Jafarizadeh, M. A.; Amiri, N.; Fouladi, N.; Ghapanvari, M.; Ranjbar, Z.

2018-04-01

The q-deformed Hamiltonian for the SO (6) ↔ U (5) transitional case in s, d interaction boson model (IBM) can be constructed by using affine SUq (1 , 1) Lie algebra in the both IBM-1 and 2 versions and IBFM. In this research paper, we have studied the energy spectra of 120-128Xe isotopes and 123-131Xe isotopes and B(E2) transition probabilities of 120-128Xe isotopes in the shape phase transition region between the spherical and gamma unstable deformed shapes of the theory of quantum deformation. The theoretical results agree with the experimental data fairly well. It is shown that the q-deformed SO (6) ↔ U (5) transitional dynamical symmetry remains after deformation.

Finite Element Analysis of Plastic Deformation During Impression Creep

NASA Astrophysics Data System (ADS)

Naveena; Ganesh Kumar, J.; Mathew, M. D.

2015-04-01

Finite element (FE) analysis of plastic deformation associated with impression creep deformation of 316LN stainless steel was carried out. An axisymmetric FE model of 10 × 10 × 10 mm specimen with 1-mm-diameter rigid cylindrical flat punch was developed. FE simulation of impression creep deformation was performed by assuming elastic-plastic-power-law creep deformation behavior. Evolution of the stress with time under the punch during elastic, plastic, and creep processes was analyzed. The onset of plastic deformation was found to occur at a nominal stress about 1.12 times the yield stress of the material. The size of the developed plastic zone was predicted to be about three times the radius of the punch. The material flow behavior and the pile-up on specimen surface have been modeled.

Macroscopic modelling of semisolid deformation for considering segregation bands induced by shear deformation

NASA Astrophysics Data System (ADS)

Morita, S.; Yasuda, H.; Nagira, T.; Gourlay, C. M.; Yoshiya, M.; Sugiyama, A.

2012-07-01

In-situ observation was carried out to observe deformation of semi-solid Fe-2mass%C steel with 65% solid and globular morphology by X-ray radiography. Deformation was predominantly controlled by the rearrangement of globules. The solid particles were pushed into each other and rearrangement caused lower solid fraction regions to form. On the basis of the observation, a macroscopic model that introduces a normal stress acting on the solid due to collisions and rearrangement is proposed. The solid particles are treated as a non-Newtonian fluid. The stiffness parameters, which characterize the flow of the solid, are introduced. Stability of semisolid to fluctuations in solid fraction during simple shear was analysed. Shear deformation can be stably localized in the semisolid with a certain solid fraction range. The model essentially reproduces band segregation formation.

The Relation Between Rotation Deformity and Nerve Root Stress in Lumbar Scoliosis

NASA Astrophysics Data System (ADS)

Kim, Ho-Joong; Lee, Hwan-Mo; Moon, Seong-Hwan; Chun, Heoung-Jae; Kang, Kyoung-Tak

Even though several finite element models of lumbar spine were introduced, there has been no model including the neural structure. Therefore, the authors made the novel lumbar spine finite element model including neural structure. Using this model, we investigated the relation between the deformity pattern and nerve root stress. Two lumbar models with different types of curve pattern (lateral bending and lateral bending with rotation curve) were made. In the model of lateral bending curves without rotation, the principal compressive nerve root stress on the concave side was greater than the principal tensile stress on the convex side at the apex vertebra. Contrarily, in the lateral bending curve with rotational deformity, the nerve stress on the convex side was higher than that on the concave side. Therefore, this study elicit that deformity pattern could have significantly influence on the nerve root stress in the lumbar spine.

A discrete model to study reaction-diffusion-mechanics systems.

PubMed

Weise, Louis D; Nash, Martyn P; Panfilov, Alexander V

2011-01-01

This article introduces a discrete reaction-diffusion-mechanics (dRDM) model to study the effects of deformation on reaction-diffusion (RD) processes. The dRDM framework employs a FitzHugh-Nagumo type RD model coupled to a mass-lattice model, that undergoes finite deformations. The dRDM model describes a material whose elastic properties are described by a generalized Hooke's law for finite deformations (Seth material). Numerically, the dRDM approach combines a finite difference approach for the RD equations with a Verlet integration scheme for the equations of the mass-lattice system. Using this framework results were reproduced on self-organized pacemaking activity that have been previously found with a continuous RD mechanics model. Mechanisms that determine the period of pacemakers and its dependency on the medium size are identified. Finally it is shown how the drift direction of pacemakers in RDM systems is related to the spatial distribution of deformation and curvature effects.

A Discrete Model to Study Reaction-Diffusion-Mechanics Systems

PubMed Central

Weise, Louis D.; Nash, Martyn P.; Panfilov, Alexander V.

2011-01-01

This article introduces a discrete reaction-diffusion-mechanics (dRDM) model to study the effects of deformation on reaction-diffusion (RD) processes. The dRDM framework employs a FitzHugh-Nagumo type RD model coupled to a mass-lattice model, that undergoes finite deformations. The dRDM model describes a material whose elastic properties are described by a generalized Hooke's law for finite deformations (Seth material). Numerically, the dRDM approach combines a finite difference approach for the RD equations with a Verlet integration scheme for the equations of the mass-lattice system. Using this framework results were reproduced on self-organized pacemaking activity that have been previously found with a continuous RD mechanics model. Mechanisms that determine the period of pacemakers and its dependency on the medium size are identified. Finally it is shown how the drift direction of pacemakers in RDM systems is related to the spatial distribution of deformation and curvature effects. PMID:21804911

Deformation and stress change associated with plate interaction at subduction zones: a kinematic modelling

NASA Astrophysics Data System (ADS)

Zhao, Shaorong; Takemoto, Shuzo

2000-08-01

The interseismic deformation associated with plate coupling at a subduction zone is commonly simulated by the steady-slip model in which a reverse dip-slip is imposed on the down-dip extension of the locked plate interface, or by the backslip model in which a normal slip is imposed on the locked plate interface. It is found that these two models, although totally different in principle, produce similar patterns for the vertical deformation at a subduction zone. This suggests that it is almost impossible to distinguish between these two models by analysing only the interseismic vertical deformation observed at a subduction zone. The steady-slip model cannot correctly predict the horizontal deformation associated with plate coupling at a subduction zone, a fact that is proved by both the numerical modelling in this study and the GPS (Global Positioning System) observations near the Nankai trough, southwest Japan. It is therefore inadequate to simulate the effect of the plate coupling at a subduction zone by the steady-slip model. It is also revealed that the unphysical assumption inherent in the backslip model of imposing a normal slip on the locked plate interface makes it impossible to predict correctly the horizontal motion of the subducted plate and the stress change within the overthrust zone associated with the plate coupling during interseismic stages. If the analysis made in this work is proved to be correct, some of the previous studies on interpreting the interseismic deformation observed at several subduction zones based on these two models might need substantial revision. On the basis of the investigations on plate interaction at subduction zones made using the finite element method and the kinematic/mechanical conditions of the plate coupling implied by the present plate tectonics, a synthesized model is proposed to simulate the kinematic effect of the plate interaction during interseismic stages. A numerical analysis shows that the proposed model, designed to simulate the motion of a subducted slab, can correctly produce the deformation and the main pattern of stress concentration associated with plate coupling at a subduction zone. The validity of the synthesized model is examined and partially verified by analysing the horizontal deformation observed by GPS near the Nankai trough, southwest Japan.

Computational fluid dynamics analysis of balloon-expandable coronary stents: influence of stent and vessel deformation.

PubMed

Martin, David M; Murphy, Eoin A; Boyle, Fergal J

2014-08-01

In many computational fluid dynamics (CFD) studies of stented vessel haemodynamics, the geometry of the stented vessel is described using non-deformed (NDF) geometrical models. These NDF models neglect complex physical features, such as stent and vessel deformation, which may have a major impact on the haemodynamic environment in stented coronary arteries. In this study, CFD analyses were carried out to simulate pulsatile flow conditions in both NDF and realistically-deformed (RDF) models of three stented coronary arteries. While the NDF models were completely idealised, the RDF models were obtained from nonlinear structural analyses and accounted for both stent and vessel deformation. Following the completion of the CFD analyses, major differences were observed in the time-averaged wall shear stress (TAWSS), time-averaged wall shear stress gradient (TAWSSG) and oscillatory shear index (OSI) distributions predicted on the luminal surface of the artery for the NDF and RDF models. Specifically, the inclusion of stent and vessel deformation in the CFD analyses resulted in a 32%, 30% and 31% increase in the area-weighted mean TAWSS, a 3%, 7% and 16% increase in the area-weighted mean TAWSSG and a 21%, 13% and 21% decrease in the area-weighted mean OSI for Stents A, B and C, respectively. These results suggest that stent and vessel deformation are likely to have a major impact on the haemodynamic environment in stented coronary arteries. In light of this observation, it is recommended that these features are considered in future CFD studies of stented vessel haemodynamics. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.