Extraction, Scrub, and Strip Test Results for the Salt Waste Processing Facility Caustic Side Solvent Extraction Solvent Sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

An Extraction, Scrub, and Strip (ESS) test was performed on a sample of Salt Waste Processing Facility (SWPF) Caustic-Side Solvent Extraction (CSSX) solvent and salt simulant to determine cesium distribution ratios (D( Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Parsons to help determine if the solvent is qualified for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations. The extraction D( Cs) measured 12.5, exceeding the required value of 8. This value is consistent with resultsmore » from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges. This revision was created to correct an error. The previous revision used an incorrect set of temperature correction coefficients which resulted in slight deviations from the correct D( Cs) results.« less

Results of initial analyses of the salt (macro) batch 9 tank 21H qualification samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

2015-10-01

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 9 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 9 composite sample indicates that the material does not display any unusual characteristics or observations, such as floating solids, the presence of large amount of solids, or unusual colors. Further results on the chemistry and other tests willmore » be issued in the future.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

Strip Effluent Hold Tank (SEHT) and Decontaminated Salt Solution Hold Tank (DSSHT) samples from several of the “microbatches” of Integrated Salt Disposition Project (ISDP) Salt Batch (“Macrobatch”) 9 have been analyzed for 238Pu, 90Sr, 137Cs, cations (Inductively Coupled Plasma Emission Spectroscopy - ICPES), and anions (Ion Chromatography Anions - IC-A). The analytical results from the current microbatch samples are similar to those from previous macrobatch samples. The Cs removal continues to be acceptable, with decontamination factors (DF) averaging 25700 (107% RSD). The bulk chemistry of the DSSHT and SEHT samples do not show any signs of unusual behavior, other thanmore » lacking the anticipated degree of dilution that is calculated to occur during Modular Caustic-Side Solvent Extraction Unit (MCU) processing.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

Strip Effluent Hold Tank (SEHT) and Decontaminated Salt Solution Hold Tank (DSSHT) samples from several of the “microbatches” of Integrated Salt Disposition Project (ISDP) Salt Batch (“Macrobatch”) 8B have been analyzed for 238Pu, 90Sr, 137Cs, cations (Inductively Coupled Plasma Emission Spectroscopy - ICPES), and anions (Ion Chromatography Anions - IC-A). The analytical results from the current microbatch samples are similar to those from previous macrobatch samples. The Cs removal continues to be excellent, with decontamination factors (DF) averaging 22,100 (114% RSD). The bulk chemistry of the DSSHT and SEHT samples does not show any signs of unusual behavior, other thanmore » lacking the anticipated degree of dilution that is calculated to occur during Modular Caustic-Side Solvent Extraction Unit (MCU) processing.« less

Thermal stability study of a new guanidine suppressor for the next-generation caustic-side solvent extraction process

DOE PAGES

Hill, Talon G.; Ensor, Dale D.; Delmau, Lætitia Helene; ...

2016-02-06

Cesium stripping performance of thermally stressed solvent degrades slowly over time in batch tests of the Next Generation Caustic-Side Solvent Extraction (NGS) process. NGS is currently used at pilot scale at the Savannah River Site for the selective removal of cesium from high-level salt waste. Recently a new guanidine, N,N',N" -tris(3,7-dimethyloctyl)guanidine (TiDG), was chosen for use as the suppressor, a lipophilic organic base needed for stripping, and the present study was undertaken to address the question of its stability. The NGS process solvent was evaluated for a period of three months under a variety of temperature and storage conditions. Themore » performance of the solvent was tested at 30-day increments using a standard extraction, scrub, strip, and extraction (ES 2S 3E) sequence. Lastly, the results provide insight on the effects of storage and process conditions, the stripping behavior of TiDG, and the stability of the new solvent composition.« less

Thermal stability study of a new guanidine suppressor for the next-generation caustic-side solvent extraction process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, Talon G.; Ensor, Dale D.; Delmau, Lætitia Helene

Cesium stripping performance of thermally stressed solvent degrades slowly over time in batch tests of the Next Generation Caustic-Side Solvent Extraction (NGS) process. NGS is currently used at pilot scale at the Savannah River Site for the selective removal of cesium from high-level salt waste. Recently a new guanidine, N,N',N" -tris(3,7-dimethyloctyl)guanidine (TiDG), was chosen for use as the suppressor, a lipophilic organic base needed for stripping, and the present study was undertaken to address the question of its stability. The NGS process solvent was evaluated for a period of three months under a variety of temperature and storage conditions. Themore » performance of the solvent was tested at 30-day increments using a standard extraction, scrub, strip, and extraction (ES 2S 3E) sequence. Lastly, the results provide insight on the effects of storage and process conditions, the stripping behavior of TiDG, and the stability of the new solvent composition.« less

Next Generation Solvent (NGS): Development for Caustic-Side Solvent Extraction of Cesium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, Bruce A.; Birdwell, Jr, Joseph F.; Bonnesen, Peter V.

This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modularmore » Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Interlaboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.« less

Next Generation Solvent Development for Caustic-Side Solvent Extraction of Cesium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moyer, Bruce A.; Birdwell, Joseph F.; Bonnesen, Peter V.

This report summarizes the FY 2010 and 2011 accomplishments at Oak Ridge National Laboratory (ORNL) in developing the Next Generation Caustic-Side Solvent Extraction (NG-CSSX) process, referred to commonly as the Next Generation Solvent (NGS), under funding from the U.S. Department of Energy, Office of Environmental Management (DOE-EM), Office of Technology Innovation and Development. The primary product of this effort is a process solvent and preliminary flowsheet capable of meeting a target decontamination factor (DF) of 40,000 for worst-case Savannah River Site (SRS) waste with a concentration factor of 15 or higher in the 18-stage equipment configuration of the SRS Modularmore » Caustic-Side Solvent Extraction Unit (MCU). In addition, the NG-CSSX process may be readily adapted for use in the SRS Salt Waste Processing Facility (SWPF) or in supplemental tank-waste treatment at Hanford upon appropriate solvent or flowsheet modifications. Efforts in FY 2010 focused on developing a solvent composition and process flowsheet for MCU implementation. In FY 2011 accomplishments at ORNL involved a wide array of chemical-development activities and testing up through single-stage hydraulic and mass-transfer tests in 5-cm centrifugal contactors. Under subcontract from ORNL, Argonne National Laboratory (ANL) designed a preliminary flowsheet using ORNL cesium distribution data, and Tennessee Technological University confirmed a chemical model for cesium distribution ratios (DCs) as a function of feed composition. Inter laboratory efforts were coordinated with complementary engineering tests carried out (and reported separately) by personnel at Savannah River National Laboratory (SRNL) and Savannah River Remediation (SRR) with helpful advice by Parsons Engineering and General Atomics on aspects of possible SWPF implementation.« less

Results of initial analyses of the salt (macro) batch 10 tank 21H qualification samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

2017-01-01

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 10 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 10 composite sample indicates that the material does not display any unusual characteristics or observations, such as floating solids, the presence of large amount of solids, or unusual colors. Further sample results will be reported in a futuremore » document. This memo satisfies part of Deliverable 3 of the Technical Task Request (TTR).« less

Results of initial analyses of the salt (macro) batch 11 Tank 21H qualification samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Interim Salt Disposition Project (ISDP) Salt (Macro) Batch 11 for processing through the Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU). This document reports the initial results of the analyses of samples of Tank 21H. Analysis of the Tank 21H Salt (Macro) Batch 11 composite sample indicates that the material does not display any unusual characteristics or observations, such as floating solids, the presence of large amounts of solids, or unusual colors. Further sample results will be reported in a futuremore » document. This memo satisfies part of Deliverable 3 of the Technical Task Request (TTR).« less

ISDP salt batch #2 supernate qualification

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.; Nash, C. A.; Fink, S. D.

2009-01-05

This report covers the laboratory testing and analyses of the second Integrated Salt Disposition Project (ISDP) salt supernate samples, performed in support of initial radioactive operations of Actinide Removal Process (ARP) and Modular Caustic-Side Solvent Extraction Unit (MCU). Major goals of this work include characterizing Tank 22H supernate, characterizing Tank 41H supernate, verifying actinide and strontium adsorption with a standard laboratory-scale test using monosodium titanate (MST) and filtration, and checking cesium mass transfer behavior for the MCU solvent performance when contacted with the liquid produced from MST contact. This study also includes characterization of a post-blend Tank 49H sample asmore » part of the Nuclear Criticality Safety Evaluation (NCSE). This work was specified by Task Technical Request and by Task Technical and Quality Assurance Plan (TTQAP). In addition, a sampling plan will be written to guide analytical future work. Safety and environmental aspects of the work were documented in a Hazard Assessment Package.« less

Analysis of an MCU HEPA filter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.; Fondeur, F. F.

A series of direct analyses on three portions (inlet, center, and outlet) of the High Efficiency Particulate Air (HEPA) filter material from the Modular Caustic-Side Solvent Extraction Unit (MCU) have been performed; this includes x-ray methods such as X-Ray Diffraction (XRD), Contained Scanning Electron Microscopy (CSEM) and X-Ray Fluorescence (XRF), as well as Fourier Transform InfraRed spectroscopy (FTIR). Additionally, two leaching studies (one with water, one with dichloromethane) have been performed on three portions (inlet, center, and outlet) of the HEPA filter material, with the leachates being analyzed by Inductively-coupled plasma emission spectroscopy (ICPES), Semi-Volatile Organic Analysis (SVOA) and gammascan.more » From the results of the analyses, SRNL feels that cesium-depleted solvent is being introduced into the HEPA filter. The most likely avenue for this is mechanical aerosolization of solvent, where the aerosol is then carried along an airstream into the HEPA filter. Once introduced into the HEPA filter media, the solvent wicks throughout the material, and migrates towards the outlet end. Once on the outlet end, continual drying could cause particulate flakes to exit the filter and travel farther down the airstream path.« less

PRELIMINARY EVALUATION OF DWPF IMPACTS OF BORIC ACID USE IN CESIUM STRIP FOR SWPF AND MCU

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stone, M.

2010-09-28

A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system includes the option to replace the current dilute nitric acid strip solution with boric acid. To support this effort, the impact of using 0.01M, 0.1M, 0.25M and 0.5M boric acid in place of 0.001M nitric acid was evaluated for impacts on the DWPF facility. The evaluation only covered the impacts of boric acid in the strip effluent and does not address the other changes in solvents (i.e., the new extractant, called MaxCalix,more » or the new suppressor, guanidine). Boric acid additions may lead to increased hydrogen generation during the SRAT and SME cycles as well as change the rheological properties of the feed. The boron in the strip effluent will impact glass composition and could require each SME batch to be trimmed with boric acid to account for any changes in the boron from strip effluent additions. Addition of boron with the strip effluent will require changes in the frit composition and could lead to changes in melt behavior. The severity of the impacts from the boric acid additions is dependent on the amount of boric acid added by the strip effluent. The use of 0.1M or higher concentrations of boric acid in the strip effluent was found to significantly impact DWPF operations while the impact of 0.01M boric acid is expected to be relatively minor. Experimental testing is required to resolve the issues identified during the preliminary evaluation. The issues to be addressed by the testing are: (1) Impact on SRAT acid addition and hydrogen generation; (2) Impact on melter feed rheology; (3) Impact on glass composition control; (4) Impact on frit production; and (5) Impact on melter offgas. A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system includes the option to replace the current dilute nitric acid strip solution with boric acid. To support this effort, the impact of using 0.01M, 0.1M, 0.25M and 0.5M boric acid in place of 0.001M nitric acid was evaluated for impacts on the DWPF facility. The evaluation only covered the impacts of boric acid in the strip effluent and does not address the other changes in solvents (i.e., the new extractant, called MaxCalix, or the new suppressor, guanidine). Experimental testing with the improved solvent is required to determine the impact of any changes in the entrained solvent on DWPF processing.« less

Heat resistant substrates and battery separators made therefrom

NASA Technical Reports Server (NTRS)

Langer, Alois (Inventor); Scala, Luciano C. (Inventor); Ruffing, Charles R. (Inventor)

1976-01-01

A flexible substrate having a caustic resistant support and at least one membrane comprising a solid polymeric matrix containing a network of interconnected pores and interdispersed inorganic filler particles with a ratio of filler: polymer in the polymeric matrix of between about 1:1 to 5:1, is made by coating at least one side of the support with a filler:coating formulation mixture of inorganic filler particles and a caustic resistant, water insoluble polymer dissolved in an organic solvent, and removing the solvent from the mixture to provide a porous network within the polymeric matrix.

Identification And Characterization Of The Solids Found In Extraction Contactor SEP-401 In June 2012

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F. F.; Fink, S. D.

2012-12-10

The Modular Caustic-Side Solvent Extraction Unit (MCU) recently conducted an outage that included maintenance on the centrifugal contactors. Operations personnel observed solids or deposits in two contactors and attempted to collect samples for analyses by Savannah River National Laboratory (SRNL). The residues found in Extraction Contactor SEP-401 are a mixture of amorphous silica, aluminosilicate, titanium, and debris from low alloy steel. The solids contain low concentrations of plutonium and strontium. These isotopes are associated with the titanium that came from the monosodium titanate (MST) added in the Actinide Removal Process (ARP) most likely as leached Ti from the MST thatmore » precipitated subsequently in MCU. An attempt was also made to obtain samples from the contents of Wash Contactor SEP-702. However, sampling provide ineffective.« less

Laboratory-scale integrated ARP filter test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poirier, M.; Burket, P.

2016-03-01

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. There is a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. This task attempted to simulate the entire ARP process, including multiple batches (5), washing, chemical cleaning, andmore » blending the feed with heels and recycle streams. The objective of the tests was to determine whether one of these processes is causing excessive fouling of the crossflow or secondary filter. The authors conducted the tests with feed solutions containing 6.6 M sodium Salt Batch 6 simulant supernate with no MST.« less

Assessment of the impact of the next generation solvent on DWPF melter off-gas flammability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daniel, W. E.

2013-02-13

An assessment has been made to evaluate the impact on the DWPF melter off-gas flammability of replacing the current solvent used in the Modular Caustic-Side Solvent Extraction Process Unit (MCU) process with the Next Generation Solvent (NGS-MCU) and blended solvent. The results of this study showed that the concentrations of nonvolatile carbon and hydrogen of the current solvent in the Slurry Mix Evaporator (SME) product would both be about 29% higher than their counterparts of the NGS-MCU and blended solvent in the absence of guanidine partitioning. When 6 ppm of guanidine (TiDG) was added to the effluent transfer to DWPFmore » to simulate partitioning for the NGS-MCU and blended solvent cases and the concentration of Isopar{reg_sign} L in the effluent transfer was controlled below 87 ppm, the concentrations of nonvolatile carbon and hydrogen of the NGS-MCU and blended solvent were still about 12% and 4% lower, respectively, than those of the current solvent. It is, therefore, concluded that as long as the volume of MCU effluent transfer to DWPF is limited to 15,000 gallons per Sludge Receipt and Adjustment Tank (SRAT)/SME cycle and the concentration of Isopar{reg_sign} L in the effluent transfer is controlled below 87 ppm, using the current solvent assumption of 105 ppm Isopar{reg_sign} L or 150 ppm solvent in lieu of NGS-MCU or blended solvent in the DWPF melter off-gas flammability assessment is conservative for up to an additional 6 ppm of TiDG in the effluent due to guanidine partitioning. This report documents the calculations performed to reach this conclusion.« less

LITERATURE REVIEW OF BORIC ACID SOLUBILITY DATA

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crapse, K.; Kyser, E.

2011-09-22

A new solvent system is being evaluated for use in the Modular Caustic-Side Solvent Extraction Unit (MCU) and in the Salt Waste Processing Facility (SWPF). The new system replaces the current dilute nitric acid strip solution with 0.01 M boric acid. This literature study is performed to determine if there is a potential for boric acid to crystallize in the lines with emphasis on the transfer lines to the Defense Waste Processing Facility. This report focuses on the aqueous phase chemistry of boric acid under conditions relevant to MCU and SWPF. Operating and transfer conditions examined for the purpose ofmore » this review include temperatures between 13 C (McLeskey, 2008) and 45 C (Fondeur, 2007) and concentrations from 0 to 3M in nitric acid as well as exposure of small amounts of entrained boric acid in the organic phase to the sodium hydroxide caustic wash stream. Experiments were also conducted to observe any chemical reactions and off-gas generation that could occur when 0.01 M boric acid solution mixes with 3 M nitric acid solution and vice versa. Based on the low concentration (0.01M) of boric acid in the MCU/SWPF strip acid and the moderate operating temperatures (13 C to 45 C), it is unlikely that crystallization of boric acid will occur in the acid strip solution under process or transfer conditions. Mixing experiments of boric and nitric acid show no measurable gas generation (< 1 cc of gas per liter of solution) under similar process conditions.« less

Sample Results From The Extraction, Scrub, And Strip Test For The Blended NGS Solvent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Washington, A. L. II; Peters, T. B.

This report summarizes the results of the extraction, scrub, and strip testing for the September 2013 sampling of the Next Generation Solvent (NGS) Blended solvent from the Modular Caustic Side-Solvent Extraction Unit (MCU) Solvent Hold Tank. MCU is in the process of transitioning from the BOBCalixC6 solvent to the NGS Blend solvent. As part of that transition, MCU has intentionally created a blended solvent to be processed using the Salt Batch program. This sample represents the first sample received from that blended solvent. There were two ESS tests performed where NGS blended solvent performance was assessed using either the Tankmore » 21 material utilized in the Salt Batch 7 analyses or a simulant waste material used in the V-5/V-10 contactor testing. This report tabulates the temperature corrected cesium distribution, or D Cs values, step recovery percentage, and actual temperatures recorded during the experiment. This report also identifies the sample receipt date, preparation method, and analysis performed in the accumulation of the listed values. The calculated extraction D Cs values using the Tank 21H material and simulant are 59.4 and 53.8, respectively. The DCs values for two scrub and three strip processes for the Tank 21 material are 4.58, 2.91, 0.00184, 0.0252, and 0.00575, respectively. The D-values for two scrub and three strip processes for the simulant are 3.47, 2.18, 0.00468, 0.00057, and 0.00572, respectively. These values are similar to previous measurements of Salt Batch 7 feed with lab-prepared blended solvent. These numbers are considered compatible to allow simulant testing to be completed in place of actual waste due to the limited availability of feed material.« less

Solvent hold tank sample results for MCU-17-150-152 (July 2017) and MCU-17-153-155 (August 2017): Quarterly report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F.; Jones, D.

A trend summary that includes the last two Solvent Hold Tank (SHT) monthly samples is shown; MCU- 17-150-152 (July SHT) and MCU-17-153-155 (August SHT). Since the last SHT sample sent for analysis was the August sample the chemical state of the solvent is best approximated by the chemical analysis of the August SHT sample (MCU-17-153-155). This report mainly focused on the chemical analysis of the August SHT sample. The analysis data from the July SHT sample are presented in the “trend” plots of this report. Analysis of the August SHT sample (MCU-17-153-155) indicated that the modifier (CS-7SB) was 2% belowmore » but the extractant (MaxCalix) concentration was at its nominal recommended level (169,000 mg/L and 46,400 mg/L respectively). The suppressor (TiDG) level has decreased since the last measurement taken while the Modular Caustic-Side Solvent Extraction unit (MCU) was operating in January 2017, but has remained steady in the range of 666 (observed in April) to 715 mg/L (observed in the August 2017 sample) since February 2017, well above the minimum recommended level (479 mg/L), but below the nominal level. The “flat” trends observed in the TiDG, MaxCalix, modifier, and Gamma measurement are consistent with the solvent being idle since January 10, 2017. A strong correlation between density and modifier concentration in the solvent continues to be observed in the SHT samples. This analysis confirms the Isopar™L addition to the solvent in January 2017. This analysis also indicates the solvent did not require further additions. Based on the current monthly sample, the levels of TiDG, Isopar™L, MaxCalix, and modifier are sufficient for continuing operation but are expected to decrease with time if the Modular Caustic-Side Solvent Extraction Unit (MCU) returns to processing radioactive liquid waste. Otherwise, the levels of these components will remain steady. A future Isopar™L trimming addition to the solvent is recommended when MCU resumes processing waste. Two unknown impurities related to the modifier (but not sec-butyl phenol: a modifier degradation product observed before) at the 290 and 110 mg/L levels were observed in the August SHT sample by the Gas - Chromatography-Mass Spectrometry (GC-MS) method. They were observed in a second GC-MS re-run with a new column. Their identification can’t be ascertained at this time. No impurities were observed in the Hydrogen Nuclear Magnetic Resonance (HNMR). Another impurity observed in the samples was mercury. Based on the August SHT sample, up to 23 ± 5 micrograms of mercury per mL of solvent was detected (the average of the Cold Vapor-Atomic Adsorption [CV-AA] and X-Ray Fluorescence [XRF] methods). The higher mercury concentration in the solvent (as determined in the last three-monthly samples) is possibly due to either a higher mercury concentration in Salt Batches 8 and 9 (Tank 49H) . The gamma level (~ 2.0E4 dpm/mL) measured in the August SHT samples was one order of magnitude lower than the gamma levels observed in the December 2016 and January 2017 SHT samples. A similar level was observed in the July SHT sample (MCU-SHT-150-152). The gamma level has remained consistently steady since January 10, 2017 when MCU stopped processing radioactive liquid waste. The laboratory will continue to monitor the quality of the solvent in particularly for any new impurities or degradation of the solvent components.« less

The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Edwards, T. B.; Stone, M. E.

2013-08-14

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01M) boric acid stream intomore » the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B2O3 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 – SB8 flowsheet to additions of B2O3 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 – SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B2O3 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B2O3 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT. The impact on CPC processing of a 0.01M boric acid solution for elution of cesium during Modular Caustic Side Solvent Extraction Unit (MCU) processing has previously been evaluated by the Savannah River National Laboratory (SRNL). Increasing the acid strength to 0.0125M boric acid to account for variations in the boric acid strength has been reviewed versus the previous evaluation. The amount of acid from the boric acid represented approximately 5% of the total acid during the previous evaluation. An increase from 0.01 to 0.0125M boric acid represents a change of approximately 1.3% which is well within the error of the acid calculation. Therefore, no significant changes to CPC processing (hydrogen generation, metal solubilities, rheological properties, REDOX control, etc.) are expected from an increase in allowable boric acid concentration from 0.01M to 0.0125M.« less

Hazardous Waste Minimization Guide for Shipyards

DTIC Science & Technology

1994-01-01

any waste generation associated with spent sol- vent. Elimination can be achieved by utiliza- tion of non-solvent cleaning agents or elimi- nating the...alkali, citric, and caustic base, are often useful substitutes for solvents. There are many for- mulations that are suited for a variety of clean- ing...agents, such as caustic soda (NaOH), are often employed in place of meth- ylene chloride based strippers. Caustic solu- tions have the advantage of

Extraction, scrub, and strip test results for the solvent transfer to salt waste processing facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T.

The Savannah River National Laboratory (SRNL) prepared approximately 240 gallons of Caustic-Side Solvent Extraction (CSSX) solvent for use at the Salt Waste Processing Facility (SWPF). An Extraction, Scrub, and Strip (ESS) test was performed on a sample of the prepared solvent using a salt solution prepared by Parsons to determine cesium distribution ratios (D(Cs)), and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams. This data will be used by Parsons to help qualify the solvent for use at the SWPF. The ESS test showed acceptable performance of the solvent for extraction, scrub, and strip operations.more » The extraction D(Cs) measured 15.5, exceeding the required value of 8. This value is consistent with results from previous ESS tests using similar solvent formulations. Similarly, scrub and strip cesium distribution ratios fell within acceptable ranges.« less

Acid hydrolysis of cellulose to yield glucose

DOEpatents

Tsao, George T.; Ladisch, Michael R.; Bose, Arindam

1979-01-01

A process to yield glucose from cellulose through acid hydrolysis. Cellulose is recovered from cellulosic materials, preferably by pretreating the cellulosic materials by dissolving the cellulosic materials in Cadoxen or a chelating metal caustic swelling solvent and then precipitating the cellulose therefrom. Hydrolysis is accomplished using an acid, preferably dilute sulfuric acid, and the glucose is yielded substantially without side products. Lignin may be removed either before or after hydrolysis.

N,N'-DICYCLOHEXYL-N"-ISOTRIDECYLGUANIDINE AS SUPPRESSOR FOR THE NEXT GENERATION CAUSTIC SIDE SOLVENT EXTRACTION (NG-CSSX) PROCESS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duncan, Nathan C; Roach, Benjamin D; Williams, Neil J

2012-01-01

ABSTRACT The purity, concentration, and source of the N,N'-dicyclohexyl-N"-isotridecylguanidine (DCiTG) suppressor (guanidine) used in the NG-CSSX process were found to influence solvent performance. As the starting isotridecanol used in the preparation of DCiTG is comprised of a mixture of branched-chain aliphatic alcohols, varying in composition with manufacturer, the resulting DCiTG itself is a mixture. Thus, it is necessary to address how the solvent performance will be affected by the different preparations of the DCiTG solvent component. In this study, four preparations of DCiTG from three sources were analyzed and evaluated for purity and performance, both in the absence and presencemore » of an anionic surfactant impurity.« less

Results of Hg speciation testing on MCU strip effluent hold tank (SEHT) and decontaminated salt solution hold tank (DSSHT) materials

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.

2015-09-17

The Savannah River National Laboratory (SRNL) was tasked with preparing and shipping samples for Hg speciation by Eurofins Frontier Global Sciences, Inc. in Seattle, WA on behalf of the Savannah River Remediation (SRR) Mercury Task Team.i,ii The tenth shipment of samples was designated to include Modular Caustic Side Solvent Extraction Unit (MCU) Strip Effluent Hold Tank (SEHT) and MCU Decontaminated Salt Solution Hold Tank (DSSHT) materials from processing Salt Batch 7b. The MCU SEHT (MCU-15-722) and DSSHT (MCU-15-709) samples were pulled on June 15, 2015. All MCU samples were received at SRNL on June 16, 2015. The DSSHT sample wasmore » moved the same day to refrigeration, while the SEHT sample was placed in the Shielded Cells. On July 9, 2015 it was opened and an aliquot diluted 1:100 with Eurofins deionized water and a portion of the diluted sample transferred to a Teflon® bottle prior to moving it to refrigeration that same day. All samples were kept in the dark and refrigerated until final dilutions were prepared for shipment to Eurofins.« less

Analytical Results from Routine DSSHT and SEHT Monthly Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

2016-08-17

Strip Effluent Hold Tank (SEHT) and Decontaminated Salt Solution Hold Tank (DSSHT) samples from several of the “microbatches” of Integrated Salt Disposition Project (ISDP) Salt Batch (“Macrobatch”) 8B have been analyzed for 238Pu, 90Sr, 137Cs, cations (Inductively Coupled Plasma Emission Spectroscopy - ICPES), and anions (Ion Chromatography Anions - IC-A). The analytical results from the current microbatch samples are similar to those from previous macrobatch samples. The Actinide Removal Process (ARP) and the Modular Caustic-Side Solvent Extraction Unit (MCU) continue to show more than adequate Pu and Sr removal for times when monosodium titanate (MST) is used. Even with nomore » MST strike being performed there exists some small Pu and Sr removal, likely from filtration of fines containing these elements. The Cs removal continues to be excellent, with decontamination factors (DF) averaging 16,400. The bulk chemistry of the DSSHT and SEHT samples do not show any signs of unusual behavior. SRNL recommends that a sample of the strip feed be analyzed for cation and anion content if a further decline in boron concentration is noted in future SEHT samples.« less

Impact of axial velocity and transmembrane pressure (TMP) on ARP filter performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poirier, M.; Burket, P.

2016-02-29

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. One potential method for increasing filter flux is to adjust the axial velocity andmore » transmembrane pressure (TMP). SRR requested SRNL to conduct bench-scale filter tests to evaluate the effects of axial velocity and transmembrane pressure on crossflow filter flux. The objective of the testing was to determine whether increasing the axial velocity at the ARP could produce a significant increase in filter flux. The authors conducted the tests by preparing slurries containing 6.6 M sodium Salt Batch 6 supernate and 2.5 g MST/L, processing the slurry through a bench-scale crossflow filter unit at varying axial velocity and TMP, and measuring filter flux as a function of time.« less

Handbook of Thermal Insulation Applications.

DTIC Science & Technology

1983-01-01

today. Every $10 spent on conservation would save at least I barrel of oil - equivalent * to buying oil at $10 a barrel. In recent years, energy...there exists some point at which’more would be spent for an increment of insulation than could ever be saved by that increment. By adding the...TO ACIDS, CAUSTICS , AND SOLVENTS: The property of a material to resist decomposition by various acids, caustics and solvents to which it may be

Modelling Bathymetric Control of Near Coastal Wave Climate. Report 2

DTIC Science & Technology

1990-04-01

given in Sub (1989), showing that the nonlinearity is important at the transects 4 and 5 where the wave has passed through the caustic cusp. Here we...pronounced, especially 22 I 3 on the right side of the caustic cusp. The overall shapes of the results of the parabolic model for 0, = 450 and 600 are...the positive z direction. The shift becomes severe with increasing angle of incidence, and it is more prominent on the right side of the caustic cusp

Extraction, -scrub, -strip test results from the interim salt disposition program macrobatch 10 tank 21H qualification samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.

Savannah River National Laboratory (SRNL) analyzed samples from Tank 21H in support of qualification of Macrobatch (Salt Batch) 10 for the Interim Salt Disposition Program (ISDP). The Salt Batch 10 characterization results were previously reported.ii,iii An Extraction, -Scrub, -Strip (ESS) test was performed to determine cesium distribution ratios (D(Cs)) and cesium concentration in the strip effluent (SE) and decontaminated salt solution (DSS) streams; this data will be used by Tank Farm Engineering to project a cesium decontamination factor (DF). This test used actual Tank 21H material, and a sample of the NGS Blend solvent currently being used at the Modularmore » Caustic-Side Solvent Extraction Unit (MCU). The ESS test showed acceptable performance with an extraction D(Cs) value of 110. This value is consistent with results from previous salt batch ESS tests using similar solvent formulations. This is better than the predicted value of 39.8 from a recently created D(Cs) model.« less

IMPROVED ANTIFOAM AGENT STUDY END OF YEAR REPORT, EM PROJECT 3.2.3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D.; Koopman, D.; Newell, J.

2011-09-30

Antifoam 747 is added to minimize foam produced by process gases and water vapor during chemical processing of sludge in the Defense Waste Processing Facility (DWPF). This allows DWPF to maximize acid addition and evaporation rates to minimize the cycle time in the Chemical Processing Cell (CPC). Improvements in DWPF melt rate due to the addition of bubblers in the melter have resulted in the need for further reductions in cycle time in the CPC. This can only be accomplished with an effective antifoam agent. DWPF production was suspended on March 22, 2011 as the result of a Flammable Gasmore » New Information/(NI) Potential Inadequacy in the Safety Analysis (PISA). The issue was that the DWPF melter offgas flammability strategy did not take into account the H and C in the antifoam, potentially flammable components, in the melter feed. It was also determined the DWPF was using much more antifoam than anticipated due to a combination of longer processing in the CPC due to high Hg, longer processing due to Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) additions, and adding more antifoam than recommended. The resolution to the PISA involved and assessment of the impact of the antifoam on melter flammability and the implementation of a strategy to control additions within acceptable levels. This led to the need to minimize the use of Antifoam 747 in processing beginning in May 2011. DWPF has had limited success in using Antifoam 747 in caustic processing. Since starting up the ARP facility, the ARP product (similar chemically to caustic sludge) is added to the Sludge Receipt and Adjustment Tank (SRAT) at boiling and evaporated to maintain a constant SRAT volume. Although there is very little offgas generated during caustic boiling, there is a large volume of water vapor produced which can lead to foaming. High additions and more frequent use of antifoam are used to mitigate the foaming during caustic boiling. The result of these three issues above is that DWPF had three antifoam needs in FY2011: (1) Determine the cause of the poor Antifoam 747 performance during caustic boiling; (2) Determine the decomposition products of Antifoam 747 during CPC processing; and (3) Improve the effectiveness of Antifoam 747, in order to minimize the amount used. Testing was completed by Illinois Institute of Technology (IIT) and Savannah River National Laboratory (SRNL) researchers to address these questions. The testing results reported were funded by both DWPF and DOE/EM 31. Both sets of results are reported in this document for completeness. The results of this research are summarized: (1) The cause for the poor Antifoam 747 performance during caustic boiling was the high hydrolysis rate, cleaving the antifoam molecule in two, leading to poor antifoam performance. In testing with pH solutions from 1 to 13, the antifoam degraded quickly at a pH < 4 and pH > 10. As the antifoam decomposed it lost its spreading ability (wetting agent performance), which is crucial to its antifoaming performance. During testing of a caustic sludge simulants, there was more foam in tests with added Antifoam 747 than in tests without added antifoam. (2) Analyses were completed to determine the composition of the two antifoam components and Antifoam 747. In addition, the decomposition products of Antifoam 747 were determined during CPC processing of sludge simulants. The main decomposition products were identified primarily as Long Chain Siloxanes, boiling point > 400 C. Total antifoam recovery was 33% by mass. In a subsequent study, various compounds potentially related to antifoam were found using semi-volatile organic analysis and volatile organic analysis on the hexane extractions and hexane rinses. These included siloxanes, trimethyl silanol, methoxy trimethyl silane, hexamethyl disiloxane, aliphatic hydrocarbons, dioctyl phthalate, and emulsifiers. Cumulatively, these species amounted to less than 3% of the antifoam mass. The majority of the antifoam was identified using carbon analysis of the SRAT product (40-80% by mass) and silicon analysis (23-83% by mass) of the condensate. Both studies recommended a better solvent for antifoam and more specific tests for antifoam degradation products than the Si and C analyses used. (3) The DWPF Antifoam 747 Purchase Specification was revised in Month, 2011 with a goal of increasing the quality of Antifoam 747. The purchase specification was changed to specify the manufacturer and product for both components that are blended by Siovation to produce Antifoam 747 for DWPF. Testing of Antifoam produced using both the old and new antifoam specifications perform very similarly in testing. Since the change in purchase specification has not improved antifoam performance, an improved antifoam agent is required.« less

Worldwide Environmental Compliance Assessment System (ECAS)

DTIC Science & Technology

1993-03-01

and other Pickling liquor and other corrosive alkalies corrosive acids Lime wastewater Spent acid Lime and water Spent mixed acid Spent caustic Spent ...labeling. packag- ing. and spill response for hazardous materials? 4. Does the installation store: * a. acids? b. caustics ? c. flammables? d. combustibles...USEPA Hazardous Waste Hazard Waste Code No. FOOl The following spent halokenated solvents used in degreasing: tetra- (T) chloroethylene, trichloroethylene

POTENTIAL IMPACT OF TANK F FLUSH SOLUTION ON H-CANYON EVAPORATOR OPERATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kyser, E.; Fondeur, F.; Fink, S.

2010-09-13

Previous chemical analysis of a sample from the liquid heel found in Tank F of the High Activity Drain (HAD) system in F/H laboratory revealed the presence of n-paraffin, tributyl phosphate (TBP), Modifier from the Modular Caustic-Side Solvent Extraction Unit (MCU) process and a vinyl ester resin that is very similar to the protective lining on Tank F. Subsequent analyses detected the presence of a small amount of diisopropylnaphthalene (DIN) (major component of Ultima Gold{trademark} AB liquid scintillation cocktail). Indications are that both vinyl ester resin and DIN are present in small amounts in the flush solution. The flush solutionmore » currently in the LR-56S trailer likely has an emulsion which is believed to contain a mixture of the reported organic species dominated by TBP. An acid treatment similar to that proposed to clear the HAD tank heel in F/H laboratory was found to allow separation of an organic phase from the cloudy sample tested by SRNL. Mixing of that clear sample did re-introduce some cloudiness that did not immediately clear but that cloudiness is attributed to the DIN in the matrix. An organic phase does quickly separate from the cloudy matrix allowing separation by a box decanter in H-Canyon prior to transfer to the evaporator feed tank. This separation should proceed normally as long as the emulsion is broken-up by acidification.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poirier, M.; Burket, P.

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). Recently, the low filter flux through the ARP of approximately 5 gallons per minute has limited the rate at which radioactive liquid waste can be treated. Salt Batch 6 had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. SRR requested SRNL to conduct bench-scale filter tests to evaluate whether sodium oxalate, sodiummore » aluminosilicate, or aluminum solids (i.e., gibbsite and boehmite) could be the cause of excessive fouling of the crossflow or secondary filter at ARP. The authors conducted the tests by preparing slurries containing 6.6 M sodium Salt Batch 6 supernate, 2.5 g MST/L slurry, and varying concentrations of sodium oxalate, sodium aluminosilicate, and aluminum solids, processing the slurry through a bench-scale filter unit that contains a crossflow primary filter and a dead-end secondary filter, and measuring filter flux and transmembrane pressure as a function of time. Among the conclusions drwn from this work are the following: (1) All of the tests showed some evidence of fouling the secondary filter. This fouling could be from fine particles passing through the crossflow filter. (2) The sodium oxalate-containing feeds behaved differently from the sodium aluminosilicate- and gibbsite/boehmite-containing feeds.« less

Effect of solvent addition sequence on lycopene extraction efficiency from membrane neutralized caustic peeled tomato waste.

PubMed

Phinney, David M; Frelka, John C; Cooperstone, Jessica L; Schwartz, Steven J; Heldman, Dennis R

2017-01-15

Lycopene is a high value nutraceutical and its isolation from waste streams is often desirable to maximize profits. This research investigated solvent addition order and composition on lycopene extraction efficiency from a commercial tomato waste stream (pH 12.5, solids ∼5%) that was neutralized using membrane filtration. Constant volume dilution (CVD) was used to desalinate the caustic salt to neutralize the waste. Acetone, ethanol and hexane were used as direct or blended additions. Extraction efficiency was defined as the amount of lycopene extracted divided by the total lycopene in the sample. The CVD operation reduced the active alkali of the waste from 0.66 to <0.01M and the moisture content of the pulp increased from 93% to 97% (wet basis), showing the removal of caustic salts from the waste. Extraction efficiency varied from 32.5% to 94.5%. This study demonstrates a lab scale feasibility to extract lycopene efficiently from tomato processing byproducts. Published by Elsevier Ltd.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cozzi, A; Cora Berry, C; Michael Bronikowski, M

The decontaminated salt solution waste stream from the Modular Caustic Side Solvent Extraction Unit and the Salt Waste Processing Facility is anticipated to contain entrained extraction solvent. The decontaminated salt solution is scheduled to be processed through Tank 50 into the Saltstone Production Facility. This study, among others, has been undertaken because the solvent concentration in the decontaminated salt solution may cause flammability issues within the Saltstone Disposal Facility that may need to be addressed prior to operation. Previous work at the Savannah River National Laboratory determined the release of Isopar{reg_sign} L from saltstone prepared with a simulated DSS withmore » Isopar{reg_sign} L concentrations ranging from 50 to 200 {micro}g/g in the salt fraction and with test temperatures ranging from ambient to 95 C. The results from the curing of the saltstone showed that the Isopar{reg_sign} L release data can be treated as a percentage of initial concentration in the concentration range studied. The majority of the Isopar{reg_sign} L that was released over the test duration was released in the first few days. The release of Isopar{reg_sign} L begins immediately and the rate of release decreases over time. At higher temperatures the immediate release is larger than at lower temperatures. In this study, saltstone was prepared using a simulated decontaminated salt solution containing Isopar{reg_sign} L concentrations of 50 {micro}L/L (30 {micro}g/g) and 100 {micro}L/L (61 {micro}g/g) and cured at 55 C. The headspace of each sample was purged and the Isopar{reg_sign} L was trapped on a coconut shell carbon tube. The amount of Isopar{reg_sign} L captured was determined using NIOSH Method 1501. The percentage of Isopar{reg_sign} L released after 20 days was 1.4 - 3.7% for saltstone containing 50 {micro}L/L concentration and 2.1 - 4.3% for saltstone containing 100 {micro}L/L concentration. Given the measurement uncertainties in this work there is no clearly discernible relationship between percentage release and initial Isopar{reg_sign} L concentration.« less

Is side-viewing endoscope assisted balloon dilatation better for corrosive gastric outlet obstruction?

PubMed

Katiyar, Prashant; Nijhawan, Sandeep; Saradava, Vimal; Nagaich, Neeraj; Gupta, Gaurav; Mathur, Amit; Nepalia, Subhash

2013-11-01

Endoscopic balloon dilatation (EBD) is an effective therapy for caustic-induced gastric outlet obstruction (GOO). Gaining access to the stricture site is the most important step. It is sometimes difficult to negotiate a balloon through the stricture with a front-viewing endoscope due to deformed anatomy of stomach. To overcome this technical difficulty, a side-viewing endoscope can be used. There is limited data regarding the use of side-viewing endoscopes in EBD. We here report on the short-term efficacy and safety of EBD in caustic-induced GOO. In technically difficult cases, a side-viewing endoscope was used for EBD and its efficacy and safety were assessed. The study included 25 patients with caustic-induced GOO. Patients underwent EBD using a through-the-scope balloon. Initial balloon dilatation was performed with a front-viewing endoscope. A side-viewing endoscope was used where negotiation across the stricture failed with a front-viewing endoscope. Dilatation was started at 8 mm diameter and was performed at 1-week intervals. The end point of dilatation was 15 mm diameter. In 18 patients successful balloon dilatation was possible with a front-viewing endoscope. A side-viewing endoscope was used in six patients as negotiation across the stricture was not possible with a front-viewing endoscope. In all six patients negotiation across the stricture followed by successful dilatation was successful with a side-viewing endoscope. Of the 25 patients included in this study, 24 (96%) achieved procedural success (18 with a front-viewing endoscope and 6 with a side-viewing endoscope) in 3-9 sessions. Our results show that EBD is a safe and effective option for caustic-induced GOO and in difficult cases a side-viewing endoscope can be used to achieve technical success.

PROJECT W-551 DETERMINATION DATA FOR EARLY LAW INTERIM PRETREATMENT SYSTEM SELECTION

DOE Office of Scientific and Technical Information (OSTI.GOV)

TEDESCHI AR

This report provides the detailed assessment forms and data for selection of the solids separation and cesium separation technology for project W-551, Interim Pretreatment System. This project will provide early pretreated low activity waste feed to the Waste Treatment Plant to allow Waste Treatment Plan Low Activity Waste facility operation prior to construction completion of the Pretreatment and High Level Waste facilities. The candidate solids separations technologies are rotary microfiltration and crossflow filtration, and the candidate cesium separation technologies are fractional crystallization, caustic-side solvent extraction, and ion-exchange using spherical resorcinol-formaldehyde resin. This data was used to prepare a cross-cutting technologymore » summary, reported in RPP-RPT-37740.« less

Archeological Survey and Testing Along Boone Creek, Louisiana Army Ammunition Plant, Webster Parish, Louisiana

DTIC Science & Technology

1989-01-01

ducks, partridges, cranes , quail, snakes, and fish. 8 CHAPTER 2: ENVIRONMENTAL SETTING Climate The modern climate of the project area is classified as... caustic materials. Large openings in their sides were cut by oil field workers, who then added water to the dry caustic material to make a caustic ...whiffletree hook and a harness ring were recovered, indicating that horses were used here. No automotive artifacts were recovered. This again reinforces the

Process for solvent refining of coal using a denitrogenated and dephenolated solvent

DOEpatents

Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

1984-01-01

A process is disclosed for the solvent refining of non-anthracitic coal at elevated temperatures and pressure in a hydrogen atmosphere using a hydrocarbon solvent which before being recycled in the solvent refining process is subjected to chemical treatment to extract substantially all nitrogenous and phenolic constituents from the solvent so as to improve the conversion of coal and the production of oil in the solvent refining process. The solvent refining process can be either thermal or catalytic. The extraction of nitrogenous compounds can be performed by acid contact such as hydrogen chloride or fluoride treatment, while phenolic extraction can be performed by caustic contact or contact with a mixture of silica and alumina.

Assessment of the Impact of a New Guanidine Suppressor In NGS on F/H Laboratory Analyses For DWPF and Saltstone MCU Transfers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bannochie, C. J.

2013-04-29

Implementation of the Next Generation Solvent (NGS) in the Modular Caustic-Side Solvent Extraction Unit (MCU) will now proceed with a new suppressor compound, 1,2,3-tris(3,7-dimethyloctyl)guanidine (TiDG), replacing the originally planned suppressor for NGS, 1,3-dicyclohexyl-2-(11-methyldodecyl) guanidine (DCiTG). The Savannah River National Laboratory (SRNL) was tasked with evaluating the potential impact to F/H Laboratory analyses supporting the Defense Waste Processing Facility (DWPF) Waste Acceptance Criteria (WAC) used to qualify transfers of MCU Strip Effluent (SE) into the facility and the Saltstone WAC used to qualify transfers of Tank 50 containing Decontaminated Salt Solution (DSS) from MCU into Saltstone. This assigned scope is coveredmore » by a Task Technical and Quality Assurance Plan (TTQAP). Previous impact evaluations were conducted when the DCiTG suppressor was planned for NGS and concluded that there was no impact to either the determination of MCU SE pH nor the analysis of Isopar® L carryover in the MCU SE and DSS streams. SRNL reported on this series of cross-check studies between the SRNL and F/H Laboratories. The change in suppressor from DCiTG to TiDG in the NGS should not impact the measurement of Isopar® L or pH in SE or DSS necessary to satisfy DWPF and Saltstone WAC (Tank 50) criteria, respectively. A statistical study of the low bias observed in Isopar® L measurements in both SRNL and F/H Laboratories may be necessary now that the final NGS composition is fixed in order to quantify the low bias so that a proper correction can be applied to measurements critical to the DWPF and Saltstone WACs. Depending upon the final DWPF WAC requirement put in place for SE pH, it could become necessary to implement an alternative ICP-AES measurement of boron. The current blended solvent system testing in SRNL should address any impacts to Isopar® L carryover into either the DSS or the SE. It is recommended that SRNL monitor the current blended solvent work underway with simulants in SRNL as well as any DWPF CPC testing done with the new SE stream to ascertain whether any need develops that could result in modification of any currently planned F/H Laboratory testing protocols.« less

The Impact Of The MCU Life Extension Solvent On Sludge Batch 8 Projected Operating Windows

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D. K.; Edwards, T. B.

2013-06-26

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NGS) and a new strip acid will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing or evaluations with the next generation solvent are required to determine the impact of these changes (if any) to Chemical Process Cell (CPC) activities, glass formulation strategies, and melter operations at the Defense Waste Processing Facility (DWPF). The introduction of the dilute (0.01 M) boric acid streammore » into the DWPF flowsheet has a potential impact on glass formulation and frit development efforts since B203 is a major oxide in frits developed for DWPF. Prior knowledge of this stream can be accounted for during frit development efforts but that was not the case for Sludge Batch 8 (SB8). Frit 803 has already been recommended and procured for SB8 processing; altering the frit to account for the incoming boron from the strip effluent (SE) is not an option for SB8. Therefore, the operational robustness of Frit 803 to the introduction of SE including its compositional tolerances (i.e., up to 0.0125M boric acid) is of interest and was the focus of this study. The primary question to be addressed in the current study was: What is the impact (if any) on the projected operating windows for the Frit 803 - SB8 flowsheet to additions of B203 from the SE in the Sludge Receipt and Adjustment Tank (SRAT)? More specifically, will Frit 803 be robust to the potential compositional changes occurring in the SRAT due to sludge variation, varying additions of ARP and/or the introduction of SE by providing access to waste loadings (WLs) of interest to DWPF? The Measurement Acceptability Region (MAR) results indicate there is very little, if any, impact on the projected operating windows for the Frit 803 - SB8 system regardless of the presence or absence of ARP and SE (up to 2 wt% B203 contained in the SRAT and up to 2000 gallons of ARP). It should be noted that 0.95 wt% B203 is the nominal projected concentration in the SRAT based on a 0.0125M boric acid flowsheet with 70,000 liters of SE being added to the SRAT.« less

LEACHING OF TITANIUM FROM MONOSODIUM TITANATE AND MODIFIED MST

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor-Pashow, K.; Fondeur, F.; Fink, S.

2012-08-01

Analysis of a fouled coalescer and pre-filters from Actinide Removal Process/Modular Caustic Side Solvent Extraction Unit (ARP/MCU) operations showed evidence of Ti containing solids. Based on these results a series of tests were planned to examine the extent of Ti leaching from monosodium titanate (MST) and modified monosodium titanate (mMST) in various solutions. The solutions tested included a series of salt solutions with varying free hydroxide concentrations, two sodium hydroxide concentrations, 9 wt % and 15 wt %, nitric and oxalic acid solutions. Overall, the amount of Ti leached from the MST and mMST was much greater in the acidmore » solutions compared to the sodium hydroxide or salt solutions, which is consistent with the expected trend. The leaching data also showed that increasing hydroxide concentration, whether pure NaOH solution used for filter cleaning in ARP or the waste salt solution, increased the amount of Ti leached from both the MST and mMST. For the respective nominal contact times with the MST solids - for filter cleaning or the normal filter operation, the dissolved Ti concentrations are comparable suggesting either cause may contribute to the increased Ti fouling on the MCU coalescers. Tests showed that Ti containing solids could be precipitated from solution after the addition of scrub acid and a decrease in temperature similar to expected in MCU operations. FTIR analysis of these solids showed some similarity to the solids observed on the fouled coalescer and pre-filters. Although only a cursory study, this information suggests that the practice of increasing free hydroxide in feed solutions to MCU as a mitigation to aluminosilicate formation may be offset by the impact of formation of Ti solids in the overall process. Additional consideration of this finding from MCU and SWPF operation is warranted.« less

Characterization of solids deposited on the modular caustic-side solvent extraction unit (MCU) coalescer media removed in October 2014

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F.

2016-03-01

In February 2015, Savannah River National Laboratory (SRNL) received a Strip Effluent (SE) coalescer (FLT-304) from MCU. That coalescer was first installed at MCU in July 2014 and removed in October 2014. While processing approximately 31,400 gallons of strip solution, the pressure drop steadily increased from 1 psi to beyond the administrative limit of 20 psi. The physical and chemical analysis was conducted on this coalescer to determine the mechanism that led to the plugging of this coalescer. Characterization of this coalescer revealed the adsorption of organic containing amines as well as MCU modifier. The amines are probably from themore » decomposition of the suppressor (TiDG) as well as from bacteria. This adsorption may have changed the surface energetics (characteristics) of the coalescer fibers and therefore, their wetting behavior. A very small amount of inorganic solids were found to have deposited on this coalescer (possibly an artifact of cleaning the coalescer with Boric acid. However, we believe that inorganic precipitation, as has been seen in the past, did not play a role in the high pressure drop rise of this coalescer. With regards to the current practice of reducing the radioactive content of the SE coalescer, it is recommended that future SE coalescer should be flushed with 10 mM boric acid which is currently used at MCU. Plugging of the SE coalescer was most likely due to the formation and accumulation of a water-in-oil emulsion that reduced the overall porosity of the coalescer. There is also evidence that a bimodal oil particle distribution may have entered and deposited in the coalescer and caused the initial increase in pressure drop.« less

4. Photocopy of photograph, U.S. Army, ca. 1943 (original print ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Photocopy of photograph, U.S. Army, ca. 1943 (original print located at Rocky Mountain Arsenal, Commerce City, Colorado). R.M.A. - 254 - CAUSTIC FUSION BLDG. LOOKING WEST. NORTH SIDE. - Rocky Mountain Arsenal, Caustic Fusion Building, 450 feet South of December Seventh Avenue; 900 feet West of D Street, Commerce City, Adams County, CO

Miscibility Evaluation Of The Next Generation Solvent With Polymers Currently Used At DWPF, MCU, And Saltstone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F. F.

The Office of Waste Processing, within the Office of Technology Innovation and Development, funded the development of an enhanced Caustic-Side Solvent Extraction (CSSX) solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. This effort lead to the development of the Next Generation Solvent (NGS) with Tris (3,7-dimethyl octyl) guanidine (TiDG). The first deployment target for the NGS solvent is within the Modular CSSX Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the new chemical components are compatible with the installed equipment. In the instance of a newmore » organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the affected facility. This report provides the calculated data from exposing these polymers to the Next Generation Solvent. An assessment of the dimensional stability of polymers known to be used or present in the MCU, Defense Waste Processing Facility (DWPF), and Saltstone facilities that will be exposed to the NGS showed that TiDG could selectively affect the elastomers and some thermoplastics to varying extents, but the typical use of these polymers in a confined geometry will likely prevent the NGS from impacting component performance. The polymers identified as of primary concern include Grafoil® (flexible graphite), Tefzel®, Isolast®, ethylene-propylene-diene monomer (EPDM) rubber, nitrile-butadiene rubber (NBR), styrene-butadiene rubber (SBR), ultra high molecular weight polyethylene (UHMWPE), and fluorocarbon rubber (FKM). Certain polymers like NBR and EPDM were found to interact mildly with NGS but their calculated swelling and the confined geometry will impede interaction with NGS. In addition, it was found that Vellumoid (cellulose fibers-reinforced glycerin and protein) may leach protein and Polyvinyl Chloride (PVC) may leach plasticizer (such as Bis-Ethylhexyl-Phthalates) into the NGS solvent. Either case will not impact decontamination or immobilization operations at Savannah River Site (SRS). Some applications have zero tolerance for dimensional changes such as the operation of valves while other applications a finite dimensional change improves the function of the application such as seals and gaskets. Additional considerations are required before using the conclusions from this work to judge outcomes in field applications. Decane, a component of Isopar L that is most likely to interact with the polymers, mildly interacted with the elastomers and the propylene based polymers but their degree of swelling is at most 10% and the confined geometry that they are typically placed in indicate this is not significant. In addition, it was found that Vellumoid may leach protein into the NGS solvent. Since Vellumoid is used at the mixer in Saltstone where it sees minimum quantities of solvent, this leaching has no effect on the extraction process at MCU or the immobilization process at saltstone. No significant interaction is expected between MaxCalix and the polymers and elastomers used at MCU, DWPF, and Saltstone. Overall, minimal and insignificant interactions are expected on extraction and immobilization operations when MCU switches from CSSX to NGS solvent. It is expected that contacting NGS will not accelerate the aging rate of polymers and elastomers under radiation and heat. This is due to the minimal interaction between NGS and the polymers and the confined geometries for these polymers. SRNL recommends the use of the HSP method (for screening) and some testing to evaluate the impact of other organic such as alcohols, glycolate, and their byproducts on the polymers used throughout the site.« less

Methods of producing adsorption media including a metal oxide

DOEpatents

Mann, Nicholas R; Tranter, Troy J

2014-03-04

Methods of producing a metal oxide are disclosed. The method comprises dissolving a metal salt in a reaction solvent to form a metal salt/reaction solvent solution. The metal salt is converted to a metal oxide and a caustic solution is added to the metal oxide/reaction solvent solution to adjust the pH of the metal oxide/reaction solvent solution to less than approximately 7.0. The metal oxide is precipitated and recovered. A method of producing adsorption media including the metal oxide is also disclosed, as is a precursor of an active component including particles of a metal oxide.

Characterization of Solids Deposited on the Modular Caustic-Side Solvent Extraction Unit (MCU) Strip Effluent (SE) Coalescer Media Removed in April 2015

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fondeur, F. F.

On June 2015, Savannah River National Laboratory (SRNL) received a Strip Effluent (SE) coalescer (FLT-304) from MCU. That coalescer was first installed at MCU in late October 2014 and removed in April 2015. While processing approximately 48,700 gallons of strip solution, the pressure drop steadily increased linearly from 1 psi to near 16 psi (the administrative limit is 17 psi) with the total filtrate volume (2.1E-4 psi/gal of filtrate). The linear behavior is due to the combined effect of a constant deposition of material that starts from the closed-end to the mid-section of the coalescer reducing the available surface areamore » of the coalescer for fluid passage (linearly with filtrate volume) and the formation of a secondary emulsion (water in NG-CSSX) on the fibers of the coalescer media. Both effects reduced the coalescer porosity by at least 13% (after processing 48,700 gallons). Before the coalescer was removed, it was flushed with a 10 mM boric acid solution to reduce the dose level. To determine the nature of the deposited material, a physical and chemical analysis of the coalescer was conducted. Characterization of this coalescer revealed the adsorption of organic containing amines (secondary amides and primary amines), TiDG, degraded modifier (with no hydroxyl group), MaxCalix, and oxidized hydrocarbon (possibly from Isopar™L or from lubricant used at MCU) onto the coalescer media. The amide and amines are possibly from the decomposition of the suppressor (TiDG). The modifier and MaxCalix were the largest components of the deposited organic material, as determined from leaching the coalescer with dichloromethane. Both the Fourier-Transformed Infrared (FTIR) and Fourier-Transformed Hydrogen Nuclear Magnetic Resonance (FT-HNMR) results indicated that some of the modifier was degraded (missing their OH groups). The modifier was observed everywhere in the examined coalescer pieces (FTIR), while the TiDG and its decomposition products were observed at the entrance discs of the coalescer. A solvent trim (a cocktail of solvent components with a high concentration of modifier) was added to the solvent on 2/22/2015. It is believed that the trim did not mix completely with the solvent and that it was subsequently spread around the MCU components including the coalescers, where it may have deposited. Chronologically, the modifier, the TiDG’s decomposition products and silicates deposited on the entrance discs first and after the pressure drop increased significantly, parts of the coalescer media detached itself from the central porous steel mandrel and a significant amount of steel debris, mercury, titanium, and additional aluminum and silicates deposited on the coalescer.« less

Conformal chemically resistant coatings for microflow devices

DOEpatents

Folta, James A.; Zdeblick, Mark

2003-05-13

A process for coating the inside surfaces of silicon microflow devices, such as electrophoresis microchannels, with a low-stress, conformal (uniform) silicon nitride film which has the ability to uniformly coat deeply-recessed cavities with, for example, aspect ratios of up to 40:1 or higher. The silicon nitride coating allows extended exposure to caustic solutions. The coating enables a microflow device fabricated in silicon to be resistant to all classes of chemicals: acids, bases, and solvents. The process involves low-pressure (vacuum) chemical vapor deposition. The ultra-low-stress silicon nitride deposition process allows 1-2 .mu.m thick films without cracks, and so enables extended chemical protection of a silicon microflow device against caustics for up to 1 year. Tests have demonstrated the resistance of the films to caustic solutions at both ambient and elevated temperatures to 65.degree. C.

Dual behavior of caustic optical beams facing obstacles

NASA Astrophysics Data System (ADS)

Vaveliuk, Pablo; Martínez-Matos, Óscar; Ren, Yu-Xuan; Lu, Rong-De

2017-06-01

A full propagation analysis on both fold-type and cusp-type caustic optical beams under various setups of obstructions is theoretically and experimentally performed. It is demonstrated that the self-healing property of caustic optical beams that include the famous Airy beam is a quite relative property. In fact, fold-type and cusp-type beams cannot only behave as self-healing beams by blocking the main intensity peak, but also behave as self-breaking ones in a nonintuitive manner: by blocking a lateral side of the beam without touching the central intensity peak. The regeneration and rupture processes of caustic beams follow a nonlocal propagation dynamic unlike the other conventional beams. Moreover, deep differences between fold and cusp caustic beams are pointed out once facing certain obstructions. The cusp-caustic beam can be broken down by the obstacle placed in a dark zone outside the caustic region, while the fold-type one remains unaltered. This beam rupture confirms the key role of a hidden propagating field in the shadow region for cusp beams that coexist with the evanescent one. The obtained results cast down the established idea that the Airy beam is a robust self-healing beam since any caustic beam can behave in a dual manner depending on the obstruction location. These facts open up different perspectives for the applications in which the self-healing properties of the beam are relevant.

2. EAST AND NORTH SIDES OF BUILDING 254. VIEW TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. EAST AND NORTH SIDES OF BUILDING 254. VIEW TO SOUTHWEST. - Rocky Mountain Arsenal, Caustic Fusion Building, 450 feet South of December Seventh Avenue; 900 feet West of D Street, Commerce City, Adams County, CO

1. SOUTH AND WEST SIDES OF BUILDING 254. VIEW TO ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. SOUTH AND WEST SIDES OF BUILDING 254. VIEW TO NORTHEAST. - Rocky Mountain Arsenal, Caustic Fusion Building, 450 feet South of December Seventh Avenue; 900 feet West of D Street, Commerce City, Adams County, CO

40 CFR 63.191 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... polycarbonate. Methylene chloride is used as a solvent in this polymerization reaction. Polysulfide rubber means... product of reaction of butadiene with excess furfural in a liquid phase reactor. R-11 is usually used as... is not limited to, the reaction of tetrahydrophthalimide and perchloromethyl mercaptan with caustic...

40 CFR 63.191 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... polycarbonate. Methylene chloride is used as a solvent in this polymerization reaction. Polysulfide rubber means... product of reaction of butadiene with excess furfural in a liquid phase reactor. R-11 is usually used as... is not limited to, the reaction of tetrahydrophthalimide and perchloromethyl mercaptan with caustic...

40 CFR 63.191 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... polycarbonate. Methylene chloride is used as a solvent in this polymerization reaction. Polysulfide rubber means... product of reaction of butadiene with excess furfural in a liquid phase reactor. R-11 is usually used as... is not limited to, the reaction of tetrahydrophthalimide and perchloromethyl mercaptan with caustic...

40 CFR 63.191 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... polycarbonate. Methylene chloride is used as a solvent in this polymerization reaction. Polysulfide rubber means... product of reaction of butadiene with excess furfural in a liquid phase reactor. R-11 is usually used as... is not limited to, the reaction of tetrahydrophthalimide and perchloromethyl mercaptan with caustic...

40 CFR 63.191 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... polycarbonate. Methylene chloride is used as a solvent in this polymerization reaction. Polysulfide rubber means... product of reaction of butadiene with excess furfural in a liquid phase reactor. R-11 is usually used as... is not limited to, the reaction of tetrahydrophthalimide and perchloromethyl mercaptan with caustic...

Centrifugal contactor operations for UREX process flowsheet. An update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pereira, Candido; Vandegrift, George F.

2014-08-01

The uranium extraction (UREX) process separates uranium, technetium, and a fraction of the iodine from the other components of the irradiated fuel in nitric acid solution. In May 2012, the time, material, and footprint requirements for treatment of 260 L batches of a solution containing 130 g-U/L were evaluated for two commercial annular centrifugal contactors from CINC Industries. These calculated values were based on the expected volume and concentration of fuel arising from treatment of a single target solution vessel (TSV). The general conclusions of that report were that a CINC V-2 contactor would occupy a footprint of 3.2 mmore » 2 (0.25 m x 15 m) if each stage required twice the nominal footprint of an individual stage, and approximately 1,131 minutes or nearly 19 hours is required to process all of the feed solution. A CINC V-5 would require approximately 9.9 m 2 (0.4 m x 25 m) of floor space but would require only 182 minutes or ~ 3 hours to process the spent target solution. Subsequent comparison with the Modular Caustic Side Solvent Extraction Unit (MCU) at Savannah River Site (SRS) in October 2013 suggested that a more compact arrangement is feasible, and the linear dimension for the CINC V-5 may be reduced to about 8 m; a comparable reduction for the CINC V-2 yields a length of 5 m. That report also described an intermediate-scale (10 cm) contactor design developed by Argonne in the early 1980s that would better align with the SHINE operations as they stood in May 2012. In this report, we revisit the previous evaluation of contactor operations after discussions with CINC Industries and analysis of the SHINE process flow diagrams for the cleanup of the TSV, which were not available at the time of the first assessment.« less

MST Filterability Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Poirier, M. R.; Burket, P. R.; Duignan, M. R.

2015-03-12

The Savannah River Site (SRS) is currently treating radioactive liquid waste with the Actinide Removal Process (ARP) and the Modular Caustic Side Solvent Extraction Unit (MCU). The low filter flux through the ARP has limited the rate at which radioactive liquid waste can be treated. Recent filter flux has averaged approximately 5 gallons per minute (gpm). Salt Batch 6 has had a lower processing rate and required frequent filter cleaning. Savannah River Remediation (SRR) has a desire to understand the causes of the low filter flux and to increase ARP/MCU throughput. In addition, at the time the testing started, SRRmore » was assessing the impact of replacing the 0.1 micron filter with a 0.5 micron filter. This report describes testing of MST filterability to investigate the impact of filter pore size and MST particle size on filter flux and testing of filter enhancers to attempt to increase filter flux. The authors constructed a laboratory-scale crossflow filter apparatus with two crossflow filters operating in parallel. One filter was a 0.1 micron Mott sintered SS filter and the other was a 0.5 micron Mott sintered SS filter. The authors also constructed a dead-end filtration apparatus to conduct screening tests with potential filter aids and body feeds, referred to as filter enhancers. The original baseline for ARP was 5.6 M sodium salt solution with a free hydroxide concentration of approximately 1.7 M.3 ARP has been operating with a sodium concentration of approximately 6.4 M and a free hydroxide concentration of approximately 2.5 M. SRNL conducted tests varying the concentration of sodium and free hydroxide to determine whether those changes had a significant effect on filter flux. The feed slurries for the MST filterability tests were composed of simple salts (NaOH, NaNO 2, and NaNO 3) and MST (0.2 – 4.8 g/L). The feed slurry for the filter enhancer tests contained simulated salt batch 6 supernate, MST, and filter enhancers.« less

Exploratory studies on some electrochemical cell systems

NASA Astrophysics Data System (ADS)

Chaudhuri, Srikumar; Guha, D.

Exploratory studies were conducted on cell systems with different metal anodes, and iodine and sulphur mixed with graphite powder in a polymer matrix as cathodes, using different electrolytes in non-aqueous and aqueous media as ionic charge carriers. The electrical conductance of the electrolyte solutions in aqueous and non-aqueous solvents, the open circuit voltage (OCV) and short circuit current (SCC) for the different cell systems were measured. To date, the non-aqueous solvents used in our studies were dimethylformamide, formamide, dioxan, and nitrobenzene, and the electrolytes used were potassium iodide, caustic potash, cetyltrimethylammonium bromide (CTAB), sodium lauryl sulphate (SLS) and calcium chloride. These electrolytes were used in both non-aqueous and aqueous media. In general, aqueous electrolyte solutions gave a better performance than non-aqueous electrolyte solutions. Of the aqueous electrolytes, the highest conductance was shown by potassium chloride solution in water (conductance=0.0334 mho). However, the best OCV and SCC were shown by aluminium as anode and iodine as cathode with a saturated solution of caustic potash in water. The OCV was 1.85 V and the SCC was 290 mA cm -2. The highest conductance among the non-aqueous systems was shown by caustic potash in formamide. (Conductance=0.013 mho.) The best OCV and SCC, however, were shown by a zinc anode and iodine cathode with saturated potassium chloride in formamide, having an OCV of 1.55 V and an SCC of 150 mA cm -2. Further studies are in progress to obtain detailed performance data and recharging characteristics of some of the more promising systems reported here.

Configurable double-sided modular jet impingement assemblies for electronics cooling

DOEpatents

Zhou, Feng; Dede, Ercan Mehmet

2018-05-22

A modular jet impingement assembly includes an inlet tube fluidly coupled to a fluid inlet, an outlet tube fluidly coupled to a fluid outlet, and a modular manifold having a first distribution recess extending into a first side of the modular manifold, a second distribution recess extending into a second side of the modular manifold, a plurality of inlet connection tubes positioned at an inlet end of the modular manifold, and a plurality of outlet connection tubes positioned at an outlet end of the modular manifold. A first manifold insert is removably positioned within the first distribution recess, a second manifold insert is removably positioned within the second distribution recess, and a first and second heat transfer plate each removably coupled to the modular manifold. The first and second heat transfer plates each comprise an impingement surface.

Temperature control transport system

DOEpatents

Schabron, John F; Sorini-Wong, Susan S

2014-12-09

Embodiments of the inventive technology may involve the use of layered, insulated PCM assemblage that itself comprises: modular insulating foam material 8 that, upon establishment as part of the assemblage, defines inner foam material sides 9 and outer foam material sides 10; thin reflective material 11 established against (whether directly in contact with or not) at least either the inner foam material sides or the outer foam materials sides, and modular, enclosed PCM sections 12 established between the modular insulating foam material and the interior center.

Environmental Compliance Assessment Army Reserve (ECAAR)

DTIC Science & Technology

1993-09-01

and water Spent mixed acid Spent caustic Spent sulfuric acid Potential Consequences: Heat generation, violent reaction. Group 2-A Group 2-B Aluminum Any...methane reforming furnaces, pulping liquor recovery furnaces, combustion devices used in the recovery of sulfur values from spent sulfuric acid...Industry and USEPA Hazardous Waste Hazard No. Hazardous Waste Code* Generic FOO1 The spent halogenated solvents used in degreasing: Trichloroethylene, (t

Mass Transfer And Hydraulic Testing Of The V-05 And V-10 Contactors With The Next Generation Solvent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herman, D. T.; Duignan, M. R.; Williams, M. R.

The Modular Caustic Side Solvent Extraction (CSSX) Unit (MCU) facility is actively pursuing the transition from the current BOBCalixC6 based solvent to the Next Generation Solvent (NGS)-MCU solvent. To support this integration of NGS into the MCU facilities, Savannah River Remediation (SRR) requested that Savannah River National Laboratory (SRNL) perform testing of a blend of the NGS (MaxCalix based solvent) with the current solvent (BOBCalixC6 based solvent) for the removal of cesium (Cs) from the liquid salt waste stream. This testing differs from prior testing by utilizing a blend of BOBCalixC6 based solvent and the NGS with the full (0.05more » M) concentration of the MaxCalix as well as a new suppressor, tris(3,7dimethyloctyl) guanidine. Single stage tests were conducted using the full size V-05 and V-10 centrifugal contactors installed at SRNL. These tests were designed to determine the mass transfer and hydraulic characteristics with the NGS solvent blended with the projected heel of the BOBCalixC6 based solvent that will exist in MCU at time of transition. The test program evaluated the amount of organic carryover and the droplet size of the organic carryover phases using several analytical methods. Stage efficiency and mass distribution ratios were determined by measuring Cs concentration in the aqueous and organic phases during single contactor testing. The nominal cesium distribution ratio, D(Cs) measured for extraction ranged from 37-60. The data showed greater than 96% stage efficiency for extraction. No significant differences were noted for operations at 4, 8 or 12 gpm aqueous salt simulant feed flow rates. The first scrub test (contact with weak caustic solution) yielded average scrub D(Cs) values of 3.3 to 5.2 and the second scrub test produced an average value of 1.8 to 2.3. For stripping behavior, the “first stage” D Cs) values ranged from 0.04 to 0.08. The efficiency of the low flow (0.27 gpm aqueous) was calculated to be 82.7%. The Spreadsheet Algorithm for Stagewise Solvent Extraction (SASSE) predicted equivalent DF for MCU from this testing is greater than 3,500 assuming 95% efficiency during extraction and 80% efficiency during scrub and strip. Hydraulically, the system performed very well in all tests. Target flows were easily obtained and stable throughout testing. Though some issues were encountered with plugging in the coalescer, they were not related to the solvent. No hydraulic upsets due to the solvent were experienced during any of the tests conducted. The first extraction coalescer element used in testing developed high pressure drop that made it difficult to maintain the target flow rates. Analysis showed an accumulation of sodium aluminosilicate solids. The coalescer was replaced with one from the same manufacturer’s lot and pressure drop was no longer an issue. Concentrations of Isopar™ L and Modifier were measured using semi-volatile organic analysis (SVOA) and high performance liquid chromatography (HPLC) to determine the amount of solvent carryover. For low-flow (0.27 gpm aqueous) conditions in stripping, SVOA measured the Isopar™ L post-contactor concentration to be 25 mg/L, HPLC measured 39 mg/L of Modifier. For moderate-flow (0.54 gpm aqueous) conditions, SVOA measured the Isopar™ L postcontactor to be ~69 mg/L, while the HPLC measured 56 mg/L for Modifier. For high-flow (0.8 gpm aqueous) conditions, SVOA measured the Isopar™ L post-contactor to be 39 mg/L. The post-coalescer (pre-decanter) measurements by SVOA for Isopar™ L were all less than the analysis detection limit of 10 mg/L. The HPLC measured 18, 22 and 20 mg/L Modifier for the low, medium, and high-low rates respectively. In extraction, the quantity of pre-coalescer Isopar™ L carryover measured by SVOA was ~280-410 mg/L at low flow (4 gpm aqueous), ~400-450 mg/L at moderate flow (8 gpm aqueous), and ~480 mg/L at high flow (12 gpm aqueous). The amount of post coalescer (pre-decanter) Isopar™ L carryover measured by SVOA was less than 45 mg/L for all flow rates. HPLC results for Modifier were 182, 217 and 222 mg/L for the post-contactor low, medium and high flow rates. The post-coalescer (pre-decanter) samples were measured to contain 12, 10 and 22 mg/L Modifier for the low, medium, and high flow rates. The carryover results and droplet size measurements were used to determine the decanter performance utilizing the decanter model developed by the ARES Corporation. Results show for the targeted salt flow rate of approximately 8 gpm, that over 93% of the solvent carryover from stripping is predicted to be recovered and over 96% solvent carryover from extraction is predicted to be recovered. This translates to a predicted solvent carryover of <3 ppm from stripping and <20 ppm solvent carryover from extraction. This projected performance at MCU is expected to be well within the operating limits and the historical performance for the baseline BOBCalixC6 based solvent. Droplet-size data obtained by MicroTrac™ S3400 analyzer consistently shows that the droplet size post-oalescer is significantly greater than the post-contactor or pre-coalescer samples. Increased flow rates did not show a consistent impact to the droplet size results. For the extraction testing, droplet size analysis showed that the post-contactor and pre-coalescer samples were essentially the same. The mean droplet sizes post-coalescer were less than the mean droplet sizes pre-coalescer with a very slight upward trend in the mean droplet size as the flow rate was increased. This result is probably due to the method of sampling. The larger post-coalescer drops immediately rise to the surface after leaving the coalescer element. The downstream sampling point was horizontally in-line with the element and therefore would only capture those organic droplets well mixed in the flowing aqueous stream.« less

PERFORMANCE IMPROVEMENT OF CROSS-FLOW FILTRATION FOR HIGH LEVEL WASTE TREATMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duignan, M.; Nash, C.; Poirier, M.

2011-01-12

In the interest of accelerating waste treatment processing, the DOE has funded studies to better understand filtration with the goal of improving filter fluxes in existing cross-flow equipment. The Savannah River National Laboratory (SRNL) was included in those studies, with a focus on start-up techniques, filter cake development, the application of filter aids (cake forming solid precoats), and body feeds (flux enhancing polymers). This paper discusses the progress of those filter studies. Cross-flow filtration is a key process step in many operating and planned waste treatment facilities to separate undissolved solids from supernate slurries. This separation technology generally has themore » advantage of self-cleaning through the action of wall shear stress created by the flow of waste slurry through the filter tubes. However, the ability of filter wall self-cleaning depends on the slurry being filtered. Many of the alkaline radioactive wastes are extremely challenging to filtration, e.g., those containing compounds of aluminum and iron, which have particles whose size and morphology reduce permeability. Unfortunately, low filter flux can be a bottleneck in waste processing facilities such as the Savannah River Modular Caustic Side Solvent Extraction Unit and the Hanford Waste Treatment Plant. Any improvement to the filtration rate would lead directly to increased throughput of the entire process. To date increased rates are generally realized by either increasing the cross-flow filter axial flowrate, limited by pump capacity, or by increasing filter surface area, limited by space and increasing the required pump load. SRNL set up both dead-end and cross-flow filter tests to better understand filter performance based on filter media structure, flow conditions, filter cleaning, and several different types of filter aids and body feeds. Using non-radioactive simulated wastes, both chemically and physically similar to the actual radioactive wastes, the authors performed several tests to demonstrate increases in filter performance. With the proper use of filter flow conditions and filter enhancers, filter flow rates can be increased over rates currently realized today.« less

Crude oil desulfurization

NASA Technical Reports Server (NTRS)

Kalvinskas, J. J.; Hsu, G. C.; Ernest, J. B. (Inventor)

1982-01-01

High sulfur crude oil is desulfurized by a low temperature (25-80 C.) chlorinolysis at ambient pressure in the absence of organic solvent or diluent but in the presence of water (water/oil=0.3) followed by a water and caustic wash to remove sulfur and chlorine containing reaction products. The process described can be practiced at a well site for the recovery of desulfurized oil used to generate steam for injection into the well for enhanced oil recovery.

Caustic Recycling Pilot Unit to Separate Sodium from LLW at Hanford Site - 12279

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pendleton, Justin; Bhavaraju, Sai; Priday, George

As part of the Department of Energy (DOE) sponsored Advanced Remediation Technologies initiative, a scheme was developed to combine Continuous Sludge Leaching (CSL), Near-Tank Cesium Removal (NTCR), and Caustic Recycling Unit (CRU) using Ceramatec technology, into a single system known as the Pilot Near-Tank Treatment System (PNTTS). The Cesium (Cs) decontaminated effluent from the NTCR process will be sent to the caustic recycle process for recovery of the caustic which will be reused in another cycle of caustic leaching in the CSL process. Such an integrated mobile technology demonstration will give DOE the option to insert this process for sodiummore » management at various sites in Hanford, and will minimize the addition of further sodium into the waste tanks. This allows for recycling of the caustic used to remove aluminum during sludge washing as a pretreatment step in the vitrification of radioactive waste which will decrease the Low Level Waste (LLW) volume by as much as 39%. The CRU pilot process was designed to recycle sodium in the form of pure sodium hydroxide. The basis for the design of the 1/4 scale pilot caustic recycling unit was to demonstrate the efficient operation of a larger scale system to recycle caustic from the NTCR effluent stream from the Parsons process. The CRU was designed to process 0.28 liter/minute of NTCR effluent, and generate 10 M concentration of 'usable' sodium hydroxide. The proposed process operates at 40 deg. C to provide additional aluminum solubility and then recover the sodium hydroxide to the point where the aluminum is saturated at 40 deg. C. A system was developed to safely separate and vent the gases generated during operation of the CRU with the production of 10 M sodium hydroxide. Caustic was produced at a rate between 1.9 to 9.3 kg/hr. The CRU was located inside an ISO container to allow for moving of the unit close to tank locations to process the LLW stream. Actual tests were conducted with the NTCR effluent simulant from the Parsons process in the CRU. The modular CRU is easily scalable as a standalone system for caustic recycling, or for NTTS integration or for use as an In-Tank Treatment System to process sodium bearing waste to meet LLW processing needs at the Hanford site. The standalone pilot operation of the CRU to recycle sodium from NTCR effluent places the technology demonstration at TRL level 6. Multiple operations were performed with the CRU to process up to 500 gallons of the NTCR effluent and demonstrate an efficient separation of up to 70 % of the sodium without solids precipitation while producing 10 M caustic. Batch mode operation was conducted to study the effects of chemistry variation, establish the processing rate, and optimize the process operating conditions to recycle caustic from the NTCR effluent. The performance of the CRU was monitored by tracking the density parameter to control the concentration of caustic produced. Different levels of sodium were separated in tests from the effluent at a fixed operating current density and temperature. The voltage of the modules remained stable during the unit operation which demonstrated steady operation to separate sodium from the NTCR effluent. The sodium transfer current efficiency was measured in testing based on the concentration of caustic produced. Measurements showed a current efficiency of 99.8% for sodium transfer from the NTCR effluent to make sodium hydroxide. The sodium and hydroxide contents of the anolyte (NTCR feed) and catholyte (caustic product) were measured before and after each batch test. In two separate batch tests, samples were taken at different levels of sodium separation and analyzed to determine the stability of the NTCR effluent after sodium separation. The stability characteristics and changes in physical and chemical properties of the NTCR effluent chemistry after separation of sodium hydroxide as a function of storage time were evaluated. Parameters such as level of precipitated alumina, total alkalinity, analysis of Al, Na, K, Cs, Fe, OH, nitrate, nitrite, total dissolved and undissolved solids, viscosity, density, and other parameters of the NTCR effluent were measured. Changes in rheology and properties of NTCR stream to support downstream handling of the effluent after sodium separation was the basis for the analysis. The results show that the NTCR effluent is stable without the precipitation of aluminum hydroxide after 70% of the sodium was separated from the effluent. (authors)« less

Wastewater Characterization and Hazardous Waste Survey, Reese Air Force Base, Texas

DTIC Science & Technology

1988-04-01

drain. The pH of caustic soda C’?- generally classifies this waste as hazardous. h. Personnel from the CE Power Production shop are neutralizing spent ...been changed out. A disposal practice for this waste will be formulated upon determination of whether or not the spent solvent is hazardous. Shop...sampling has been S performed to determine the characteristics of this waste. Spent rags are also thrown in the trash. Personnel also perform cadmium

Side-channel Analysis of Subscriber Identity Modules

DTIC Science & Technology

2013-06-01

with fuming nitric acid or a similar caustic chemical. Once the die is bare, the problem of extreme miniaturization can be mitigated with the use of...laboratory. Had this possibility been considered earlier, less time would have been spent attempting to work around the probe limitations. 5.3 Future

Evaluation of the Hydraulic Performance and Mass Transfer Efficiency of the CSSX Process with the Optimized Solvent in a Single Stage of 5.5-Cm Diameter Centrifugal Contactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Law, J.D.; Tillotson, R.D.; Todd, T.A.

2002-09-19

The Caustic-Side Solvent Extraction (CSSX) process has been selected for the separation of cesium from Savannah River Site high-level waste. The solvent composition used in the CSSX process was recently optimized so that the solvent is no longer supersaturated with respect to the calixarene crown ether extractant. Hydraulic performance and mass transfer efficiency testing of a single stage of 5.5-cm ORNL-designed centrifugal contactor has been performed for the CSSX process with the optimized solvent. Maximum throughputs of the 5.5-cm centrifugal contactor, as a function of contactor rotor speed, have been measured for the extraction, scrub, strip, and wash sections ofmore » the CSSX flowsheet at the baseline organic/aqueous flow ratios (O/A) of the process, as well as at O/A's 20% higher and 20% lower than the baseline. Maximum throughputs are comparable to the design throughput of the contactor, as well as with throughputs obtained previously in a 5-cm centrifugal contactor with the non-optimized CSSX solvent formulation. The 20% variation in O/A had minimal effect on contactor throughput. Additionally, mass transfer efficiencies have been determined for the extraction and strip sections of the flowsheet. Efficiencies were lower than the process goal of greater than or equal to 80%, ranging from 72 to 75% for the extraction section and from 36 to 60% in the strip section. Increasing the mixing intensity and/or the solution level in the mixing zone of the centrifugal contactor (residence time) could potentially increase efficiencies. Several methods are available to accomplish this including (1) increasing the size of the opening in the bottom of the rotor, resulting in a contactor which is partially pumping instead of fully pumping, (2) decreasing the number of vanes in the contactor, (3) increasing the vane height, or (4) adding vanes on the rotor and baffles on the housing of the contactor. The low efficiency results obtained stress the importance of proper design of a centrifugal contactor for use in the CSSX process. A prototype of any centrifugal contactors designed for future pilot-scale or full-scale processing should be thoroughly tested prior to implementation.« less

Evaluation of the Hydraulic Capacity and Mass Transfer Efficiency of the CSSX Process with the Optimized Solvent in a Single Stage of 5.5-cm-Diameter Centrifugal Contactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Law, Jack Douglas; Tillotson, Richard Dean; Todd, Terry Allen

2002-09-01

The Caustic-Side Solvent Extraction (CSSX) process has been selected for the separation of cesium from Savannah River Site high-level waste. The solvent composition used in the CSSX process was recently optimized so that the solvent is no longer supersaturated with respect to the calixarene crown ether extractant. Hydraulic performance and mass transfer efficiency testing of a single stage of 5.5-cm ORNL-designed centrifugal contactor has been performed for the CSSX process with the optimized solvent. Maximum throughputs of the 5.5-cm centrifugal contactor, as a function of contactor rotor speed, have been measured for the extraction, scrub, strip, and wash sections ofmore » the CSSX flowsheet at the baseline organic/aqueous flow ratios (O/A) of the process, as well as at O/A’s 20% higher and 20% lower than the baseline. Maximum throughputs are comparable to the design throughput of the contactor, as well as with throughputs obtained previously in a 5-cm centrifugal contactor with the non-optimized CSSX solvent formulation. The 20% variation in O/A had minimal effect on contactor throughput. Additionally, mass transfer efficiencies have been determined for the extraction and strip sections of the flowsheet. Efficiencies were lower than the process goal of greater than or equal to 80%, ranging from 72 to 75% for the extraction section and from 36 to 60% in the strip section. Increasing the mixing intensity and/or the solution level in the mixing zone of the centrifugal contactor (residence time) could potentially increase efficiencies. Several methods are available to accomplish this including (1) increasing the size of the opening in the bottom of the rotor, resulting in a contactor which is partially pumping instead of fully pumping, (2) decreasing the number of vanes in the contactor, (3) increasing the vane height, or (4) adding vanes on the rotor and baffles on the housing of the contactor. The low efficiency results obtained stress the importance of proper design of a centrifugal contactor for use in the CSSX process. A prototype of any centrifugal contactors designed for future pilot-scale or full-scale processing should be thoroughly tested prior to implementation.« less

THE IMPACT OF THE MCU LIFE EXTENSION SOLVENT ON DWPF GLASS FORMULATION EFFORTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peeler, D; Edwards, T

2011-03-24

As a part of the Actinide Removal Process (ARP)/Modular Caustic Side Solvent Extraction Unit (MCU) Life Extension Project, a next generation solvent (NG-CSSX), a new strip acid, and modified monosodium titanate (mMST) will be deployed. The strip acid will be changed from dilute nitric acid to dilute boric acid (0.01 M). Because of these changes, experimental testing with the next generation solvent and mMST is required to determine the impact of these changes in 512-S operations as well as Chemical Process Cell (CPC), Defense Waste Processing Facility (DWPF) glass formulation activities, and melter operations at DWPF. To support programmatic objectives,more » the downstream impacts of the boric acid strip effluent (SE) to the glass formulation activities and melter operations are considered in this study. More specifically, the impacts of boric acid additions to the projected SB7b operating windows, potential impacts to frit production temperatures, and the potential impact of boron volatility are evaluated. Although various boric acid molarities have been reported and discussed, the baseline flowsheet used to support this assessment was 0.01M boric acid. The results of the paper study assessment indicate that Frit 418 and Frit 418-7D are robust to the implementation of the 0.01M boric acid SE into the SB7b flowsheet (sludge-only or ARP-added). More specifically, the projected operating windows for the nominal SB7b projections remain essentially constant (i.e., 25-43 or 25-44% waste loading (WL)) regardless of the flowsheet options (sludge-only, ARP added, and/or the presence of the new SE). These results indicate that even if SE is not transferred to the Sludge Receipt and Adjustment Tank (SRAT), there would be no need to add boric acid (from a trim tank) to compositionally compensate for the absence of the boric acid SE in either a sludge-only or ARP-added SB7b flowsheet. With respect to boron volatility, the Measurement Acceptability Region (MAR) assessments also suggest that Slurry Mix Evaporator (SME) acceptability decisions would not be different assuming either 100% of the B{sub 2}O{sub 3} from the SE were retained or volatilized. More specifically, the 0.84 wt% B{sub 2}O{sub 3} in the SE is so minor that its presence in the SME analysis does not influence SME acceptability decisions. In fact, using the 100% retention and 100% volatilization composition projections, only minor differences in the predicted properties of the glass product occur with all of the glasses being acceptable over a WL interval of 32-42%. Based on the 0.01M boric acid flowsheet, there is very little difference between Frit 418 and Frit 418-7D (a frit that was compositionally altered to account for the 0.84 wt% B{sub 2}O{sub 3} in the SE) with respect to melt temperature. In fact, when one evaluates the composition of Frit 418-7D, it lies within the current Frit 418 vendor specifications and therefore could have been produced by the vendor targeting the nominal composition of Frit 418.« less

A uniform geometrical optics and an extended uniform geometrical theory of diffraction for evaluating high frequency EM fields near smooth caustics and composite shadow boundaries

NASA Technical Reports Server (NTRS)

Constantinides, E. D.; Marhefka, R. J.

1994-01-01

A uniform geometrical optics (UGO) and an extended uniform geometrical theory of diffraction (EUTD) are developed for evaluating high frequency electromagnetic (EM) fields within transition regions associated with a two and three dimensional smooth caustic of reflected rays and a composite shadow boundary formed by the caustic termination or the confluence of the caustic with the reflection shadow boundary (RSB). The UGO is a uniform version of the classic geometrical optics (GO). It retains the simple ray optical expressions of classic GO and employs a new set of uniform reflection coefficients. The UGO also includes a uniform version of the complex GO ray field that exists on the dark side of the smooth caustic. The EUTD is an extension of the classic uniform geometrical theory of diffraction (UTD) and accounts for the non-ray optical behavior of the UGO reflected field near caustics by using a two-variable transition function in the expressions for the edge diffraction coefficients. It also uniformly recovers the classic UTD behavior of the edge diffracted field outside the composite shadow boundary transition region. The approach employed for constructing the UGO/EUTD solution is based on a spatial domain physical optics (PO) radiation integral representation for the fields which is then reduced using uniform asymptotic procedures. The UGO/EUTD analysis is also employed to investigate the far-zone RCS problem of plane wave scattering from two and three dimensional polynomial defined surfaces, and uniform reflection, zero-curvature, and edge diffraction coefficients are derived. Numerical results for the scattering and diffraction from cubic and fourth order polynomial strips are also shown and the UGO/EUTD solution is validated by comparison to an independent moment method (MM) solution. The UGO/EUTD solution is also compared with the classic GO/UTD solution. The failure of the classic techniques near caustics and composite shadow boundaries is clearly demonstrated and it is shown that the UGO/EUTD results remain valid and uniformly reduce to the classic results away from the transition regions. Mathematical details on the asymptotic properties and efficient numerical evaluation of the canonical functions involved in the UGO/EUTD expressions are also provided.

Quartz crystal growth

DOEpatents

Baughman, Richard J.

1992-01-01

A process for growing single crystals from an amorphous substance that can undergo phase transformation to the crystalline state in an appropriate solvent. The process is carried out in an autoclave having a lower dissolution zone and an upper crystallization zone between which a temperature differential (.DELTA.T) is maintained at all times. The apparatus loaded with the substance, solvent, and seed crystals is heated slowly maintaining a very low .DELTA.T between the warmer lower zone and cooler upper zone until the amorphous substance is transformed to the crystalline state in the lower zone. The heating rate is then increased to maintain a large .DELTA.T sufficient to increase material transport between the zones and rapid crystallization. .alpha.-Quartz single crystal can thus be made from fused quartz in caustic solvent by heating to 350.degree. C. stepwise with a .DELTA.T of 0.25.degree.-3.degree. C., increasing the .DELTA.T to about 50.degree. C. after the fused quartz has crystallized, and maintaining these conditions until crystal growth in the upper zone is completed.

IDENTIFICATION OF MEMBERS IN THE CENTRAL AND OUTER REGIONS OF GALAXY CLUSTERS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Serra, Ana Laura; Diaferio, Antonaldo, E-mail: serra@ph.unito.it

2013-05-10

The caustic technique measures the mass of galaxy clusters in both their virial and infall regions and, as a byproduct, yields the list of cluster galaxy members. Here we use 100 galaxy clusters with mass M{sub 200} {>=} 10{sup 14} h {sup -1} M{sub Sun} extracted from a cosmological N-body simulation of a {Lambda}CDM universe to test the ability of the caustic technique to identify the cluster galaxy members. We identify the true three-dimensional members as the gravitationally bound galaxies. The caustic technique uses the caustic location in the redshift diagram to separate the cluster members from the interlopers. Wemore » apply the technique to mock catalogs containing 1000 galaxies in the field of view of 12 h {sup -1} Mpc on a side at the cluster location. On average, this sample size roughly corresponds to 180 real galaxy members within 3r{sub 200}, similar to recent redshift surveys of cluster regions. The caustic technique yields a completeness, the fraction of identified true members, f{sub c} = 0.95 {+-} 0.03, within 3r{sub 200}. The contamination, the fraction of interlopers in the observed catalog of members, increases from f{sub i}=0.020{sup +0.046}{sub -0.015} at r{sub 200} to f{sub i}=0.08{sup +0.11}{sub -0.05} at 3r{sub 200}. No other technique for the identification of the members of a galaxy cluster provides such large completeness and small contamination at these large radii. The caustic technique assumes spherical symmetry and the asphericity of the cluster is responsible for most of the spread of the completeness and the contamination. By applying the technique to an approximately spherical system obtained by stacking the individual clusters, the spreads decrease by at least a factor of two. We finally estimate the cluster mass within 3r{sub 200} after removing the interlopers: for individual clusters, the mass estimated with the virial theorem is unbiased and within 30% of the actual mass; this spread decreases to less than 10% for the spherically symmetric stacked cluster.« less

Electrical machines and assemblies including a yokeless stator with modular lamination stacks

DOEpatents

Qu, Ronghai; Jansen, Patrick Lee; Bagepalli, Bharat Sampathkumar; Carl, Jr., Ralph James; Gadre, Aniruddha Dattatraya; Lopez, Fulton Jose

2010-04-06

An electrical machine includes a rotor with an inner rotor portion and an outer rotor portion, and a double-sided yokeless stator. The yokeless stator includes modular lamination stacks and is configured for radial magnetic flux flow. The double-sided yokeless stator is concentrically disposed between the inner rotor portion and the outer rotor portion of the electrical machine. Examples of particularly useful embodiments for the electrical machine include wind turbine generators, ship propulsion motors, switch reluctance machines and double-sided synchronous machines.

Modular Polymer Biosensors by Solvent Immersion Imprint Lithography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Jayven S.; Xantheas, Sotiris S.; Grate, Jay W.

2016-01-01

We recently demonstrated Solvent Immersion Imprint Lithography (SIIL), a rapid benchtop microsystem prototyping technique, including polymer functionalization, imprinting and bonding. Here, we focus on the realization of planar polymer sensors using SIIL through simple solvent immersion without imprinting. We describe SIIL’s impregnation characteristics, including an inherent mechanism that not only achieves practical doping concentrations, but their unexpected 4-fold enhancement compared to the immersion solution. Subsequently, we developed and characterized optical sensors for detecting molecular O2. To this end, a high dynamic range is reported, including its control through the immersion duration, a manifestation of SIIL’s modularity. Overall, SIIL exhibits themore » potential of improving the operating characteristics of polymer sensors, while significantly accelerating their prototyping, as it requires a few seconds of processing and no need for substrates or dedicated instrumentation. These are critical for O2 sensing as probed by way of example here, as well as any polymer permeable reactant.« less

Oxygen-consuming chlor alkali cell configured to minimize peroxide formation

DOEpatents

Chlistunoff, Jerzy B [Los Alamos, NM; Lipp, Ludwig [Brookfield, CT; Gottesfeld, Shimshon [Niskayuna, NY

2006-08-01

Oxygen-consuming zero gap chlor-alkali cell was configured to minimize peroxide formation. The cell included an ion-exchange membrane that divided the cell into an anode chamber including an anode and a cathode chamber including an oxygen gas diffusion cathode. The cathode included a single-piece of electrically conducting graphitized carbon cloth. Catalyst and polytetrafluoroethylene were attached to only one side of the cloth. When the cathode was positioned against the cation exchange membrane with the catalyst side away from the membrane, electrolysis of sodium chloride to chlorine and caustic (sodium hydroxide) proceeded with minimal peroxide formation.

12. FIRST FLOOR BLD 28B: DETAIL SOLVENT PUMPS. Fafnir ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

12. FIRST FLOOR BLD 28B: DETAIL SOLVENT PUMPS. - Fafnir Bearing Plant, Bounded on North side by Myrtle Street, on South side by Orange Street, on East side by Booth Street & on West side by Grove Street, New Britain, Hartford County, CT

In-situ caustic generation from sewage: the impact of caustic strength and sewage composition.

PubMed

Pikaar, Ilje; Rozendal, René A; Rabaey, Korneel; Yuan, Zhiguo

2013-10-01

Periodic caustic dosage is a commonly used method by the water industry to elevate pH levels and deactivate sewer biofilms responsible for hydrogen sulfide generation. Caustic (NaOH) can be generated in-situ from sewage using a divided electrochemical cell, which avoids the need for transport, handling and storage of concentrated caustic solutions. In this study, we investigated the impact of caustic strength in the cathode compartment and the impact of sodium concentration in sewage on the Coulombic efficiency (CE) for caustic generation. The CE was found to be independent of the caustic strength produced in the range of up to ~3 wt%. Results showed that a caustic solution of ~3 wt% could be produced directly from sewage at a CE of up to 75 ± 0.5%. The sodium concentration in sewage had a significant impact on the CE for caustic generation as well as on the energy requirements of the system, with a higher sodium concentration leading to a higher CE and lower energy consumption. The proton, calcium, magnesium and ammonium concentrations in sewage affected the CE for caustic generation, especially at low sodium concentrations. Economical assessment based on the experimental results indicated that sulfide control in sewers using electrochemically-generated caustic from sewage is an economically attractive strategy. Copyright © 2013 Elsevier Ltd. All rights reserved.

CHARACTERIZATION OF THE RESONANT CAUSTIC PERTURBATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, Sun-Ju, E-mail: sjchung@kasi.re.k

Four of nine exoplanets found by microlensing were detected by the resonant caustic, which represents the merging of the planetary and central caustics at the position when the projected separation of a host star and a bounded planet is s approx 1. One of the resonant caustic lensing events, OGLE-2005-BLG-169, was a caustic-crossing high-magnification event with A {sub max}approx 800 and the source star was much smaller than the caustic, nevertheless the perturbation was not obviously apparent on the light curve of the event. In this paper, we investigate the perturbation pattern of the resonant caustic to understand why themore » perturbations induced by the caustic do not leave strong traces on the light curves of high-magnification events despite a small source/caustic size ratio. From this study, we find that the regions with small magnification excess around the center of the resonant caustic are rather widely formed, and the event passing the small-excess region produces a high-magnification event with a weak perturbation that is small relative to the amplification caused by the star and thus does not noticeably appear on the light curve of the event. We also find that the positive excess of the inside edge of the resonant caustic and the negative excess inside the caustic become stronger and wider as q increases, and thus the resonant caustic-crossing high-magnification events with the weak perturbation occur in the range of q <= 10{sup -4}. We determine the probability of the occurrence of events with the small excess |epsilon| <= 3% in high-magnification events induced by a resonant caustic. As a result, we find that for Earth-mass planets with a separation of approx2.5 AU the resonant caustic high-magnification events with the weak perturbation can occur with a significant frequency.« less

11. FIRST FLOOR BLDG. 28B: OVERVIEW SOLVENT PUMPS AND HEATING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. FIRST FLOOR BLDG. 28B: OVERVIEW SOLVENT PUMPS AND HEATING LOOKING WEST. - Fafnir Bearing Plant, Bounded on North side by Myrtle Street, on South side by Orange Street, on East side by Booth Street & on West side by Grove Street, New Britain, Hartford County, CT

Duality of caustics in Minkowski billiards

NASA Astrophysics Data System (ADS)

Artstein-Avidan, S.; Florentin, D. I.; Ostrover, Y.; Rosen, D.

2018-04-01

In this paper we study convex caustics in Minkowski billiards. We show that for the Euclidean billiard dynamics in a planar smooth, centrally symmetric, strictly convex body K, for every convex caustic which K possesses, the ‘dual’ billiard dynamics in which the table is the Euclidean unit ball and the geometry that governs the motion is induced by the body K, possesses a dual convex caustic. Such a pair of caustics are dual in a strong sense, and in particular they have the same perimeter, Lazutkin parameter (both measured with respect to the corresponding geometries), and rotation number. We show moreover that for general Minkowski billiards this phenomenon fails, and one can construct a smooth caustic in a Minkowski billiard table which possesses no dual convex caustic.

Process for hydroliquefying coal or like carbonaceous solid materials

DOEpatents

Malek, John Michael

1977-01-01

In this process the products of the dissolution-hydrogenation of coal or the like material in a hydrocarbon rich solvent are subjected in their slurryform fraction to an asphaltenes decomposing action of an alkali, like caustic soda or, being admixed after the gasiform fraction of the hydrogenation products has been taken off the slurryform fraction of the hydrogenation products now including the admixed alkali is subjected to a rehydrogenation by a hydrogen rich gas which after its rehydrogenating use is preferably applied, as source of hydrogen, to said dissolution-hydrogenation of coal. Optionally the admixed alkali includes minor amounts of a carboxylic acid salt of calcium.

Moist caustic leaching of coal

DOEpatents

Nowak, Michael A.

1994-01-01

A process for reducing the sulfur and ash content of coal. Particulate coal is introduced into a closed heated reaction chamber having an inert atmosphere to which is added 50 mole percent NaOH and 50 mole percent KOH moist caustic having a water content in the range of from about 15% by weight to about 35% by weight and in a caustic to coal weight ratio of about 5 to 1. The coal and moist caustic are kept at a temperature of about 300.degree. C. Then, water is added to the coal and caustic mixture to form an aqueous slurry, which is washed with water to remove caustic from the coal and to produce an aqueous caustic solution. Water is evaporated from the aqueous caustic solution until the water is in the range of from about 15% by weight to about 35% by weight and is reintroduced to the closed reaction chamber. Sufficient acid is added to the washed coal slurry to neutralize any remaining caustic present on the coal, which is thereafter dried to produce desulfurized coal having not less than about 90% by weight of the sulfur present in the coal feed removed and having an ash content of less than about 2% by weight.

Caustics and Caustic-Interference in Measurements of Contact Angle and Flow Visualization Through Laser Shadowgraphy

NASA Technical Reports Server (NTRS)

Chao, David F.; Zhang, Neng-Li

2002-01-01

As one of the basic elements of the shadowgraphy optical system, the image of the far field from the droplet implicates plentiful information on the droplet profile. An analysis of caustics by wave theory shows that a droplet with a cylindrically symmetric Gaussian-hill-type profile produces a circular directional caustic in far field, which arises from the singularities (inflection line on the surface). The sessile liquid droplets, which profiles are restricted by surface tension, usually have a 'protruding foot' where the surface inflects. Simple geometrical optics indicates that the circular caustic stemming from the surface inflection at the protruding-foot takes the shape of the outmost ring on the image of the far field. It is the diameter of the outmost ring that is used as one of the key parameters in the measurements of contact angle through the laser shadowgraphic method. Different surface characteristics of the droplets produce different type of caustics, and therefore, the shape of the caustics can be used to determine the surface property of the sessile droplets. The present paper describes the measurement method of contact angIe using the circular caustics and the estimation of the protruding-foot height through the caustic interference.

SLUDGE BATCH 6/TANK 40 SIMULANT CHEMICAL PROCESS CELL SIMULATIONS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koopman, David

2010-04-28

Phase III simulant flowsheet testing was completed using the latest composition estimates for SB6/Tank 40 feed to DWPF. The goals of the testing were to determine reasonable operating conditions and assumptions for the startup of SB6 processing in the DWPF. Testing covered the region from 102-159% of the current DWPF stoichiometric acid equation. Nitrite ion concentration was reduced to 90 mg/kg in the SRAT product of the lowest acid run. The 159% acid run reached 60% of the DWPF Sludge Receipt and Adjustment Tank (SRAT) limit of 0.65 lb H2/hr, and then sporadically exceeded the DWPF Slurry Mix Evaporator (SME)more » limit of 0.223 lb H2/hr. Hydrogen generation rates peaked at 112% of the SME limit, but higher than targeted wt% total solids levels may have been partially responsible for rates seen. A stoichiometric factor of 120% met both objectives. A processing window for SB6 exists from 102% to something close to 159% based on the simulant results. An initial recommendation for SB6 processing is at 115-120% of the current DWPF stoichiometric acid equation. The addition of simulated Actinide Removal Process (ARP) and Modular Caustic Side Solvent Extraction Unit (MCU) streams to the SRAT cycle had no apparent impact on the preferred stoichiometric factor. Hydrogen generation occurred continuously after acid addition in three of the four tests. The three runs at 120%, 118.4% with ARP/MCU, and 159% stoichiometry were all still producing around 0.1 lb hydrogen/hr at DWPF scale after 36 hours of boiling in the SRAT. The 120% acid run reached 23% of the SRAT limit and 37% of the SME limit. Conversely, nitrous oxide generation was subdued compared to previous sludge batches, staying below 29 lb/hr in all four tests or about a fourth as much as in comparable SB4 testing. Two processing issues, identified during SB6 Phase II flowsheet testing and qualification simulant testing, were monitored during Phase III. Mercury material balance closure was impacted by acid stoichiometry, and significant mercury was not accounted for in the highest acid run. Coalescence of elemental mercury droplets in the mercury water wash tank (MWWT) appeared to degrade with increasing stoichiometry. Observations were made of mercury scale formation in the SRAT condenser and MWWT. A tacky mercury amalgam with Rh, Pd, and Cu, plus some Ru and Ca formed on the impeller at 159% acid. It contained a significant fraction of the available Pd, Cu, and Rh as well as about 25% of the total mercury charged. Free (elemental) mercury was found in all of the SME products. Ammonia scrubbers were used during the tests to capture off-gas ammonia for material balance purposes. Significant ammonium ion formation was again observed during the SRAT cycle, and ammonia gas entered the off-gas as the pH rose during boiling. Ammonium ion production was lower than in the SB6 Phase II and the qualification simulant testing. Similar ammonium ion formation was seen in the ARP/MCU simulation as in the 120% flowsheet run. A slightly higher pH caused most of the ammonium to vaporize and collect in the ammonia scrubber reflux solution. Two periods of foaminess were noted. Neither required additional antifoam to control the foam growth. A steady foam layer formed during reflux in the 120% acid run. It was about an inch thick, but was 2-3 times more volume of bubbles than is typically seen during reflux. A similar foam layer also was seen during caustic boiling of the simulant during the ARP addition. While frequently seen with the radioactive sludge, foaminess during caustic boiling with simulants has been relatively rare. Two further flowsheet tests were performed and will be documented separately. One test was to evaluate the impact of process conditions that match current DWPF operation (lower rates). The second test was to evaluate the impact of SRAT/SME processing on the rheology of a modified Phase III simulant that had been made five times more viscous using ultrasonication.« less

Novel Use of Ophthalmic pH Paper to Diagnose Malicious Caustic Ingestion in a Pediatric Patient

PubMed Central

Bruno, Eric C.

2018-01-01

Occult caustic ingestion in the pediatric population is a challenging diagnosis to make in the emergency department. Failure to suspect and diagnose a caustic ingestion can lead to potentially life-changing comorbidities. Historically, the diagnosis of caustic ingestion has been clinical without any suitable diagnostic tools to aid in the suspicion of occult cases. In this case, we describe a novel use of ophthalmic pH paper to diagnose caustic ingestion in a three-year-old.

DEMONSTRATION OF THE NEXT-GENERATION CAUSTIC-SIDE SOLVENT EXTRACTION SOLVENT WITH 2-CM CENTRIFUGAL CONTRACTORS USING TANK 49H WASTE AND WASTE SIMULANT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pierce, R.; Peters, T.; Crowder, M.

2011-09-27

Researchers successfully demonstrated the chemistry and process equipment of the Caustic-Side Solvent Extraction (CSSX) flowsheet using MaxCalix for the decontamination of high level waste (HLW). The demonstration was completed using a 12-stage, 2-cm centrifugal contactor apparatus at the Savannah River National Laboratory (SRNL). This represents the first CSSX process demonstration of the MaxCalix solvent system with Savannah River Site (SRS) HLW. Two tests lasting 24 and 27 hours processed non-radioactive simulated Tank 49H waste and actual Tank 49H HLW, respectively. Conclusions from this work include the following. The CSSX process is capable of reducing {sup 137}Cs in high level radioactivemore » waste by a factor of more than 40,000 using five extraction, two scrub, and five strip stages. Tests demonstrated extraction and strip section stage efficiencies of greater than 93% for the Tank 49H waste test and greater than 88% for the simulant waste test. During a test with HLW, researchers processed 39 liters of Tank 49H solution and the waste raffinate had an average decontamination factor (DF) of 6.78E+04, with a maximum of 1.08E+05. A simulant waste solution ({approx}34.5 liters) with an initial Cs concentration of 83.1 mg/L was processed and had an average DF greater than 5.9E+03, with a maximum DF of greater than 6.6E+03. The difference may be attributable to differences in contactor stage efficiencies. Test results showed the solvent can be stripped of cesium and recycled for {approx}25 solvent turnovers without the occurrence of any measurable solvent degradation or negative effects from minor components. Based on the performance of the 12-stage 2-cm apparatus with the Tank 49H HLW, the projected DF for MCU with seven extraction, two scrub, and seven strip stages operating at a nominal efficiency of 90% is {approx}388,000. At 95% stage efficiency, the DF in MCU would be {approx}3.2 million. Carryover of organic solvent in aqueous streams (and aqueous in organic streams) was less than 0.1% when processing Tank 49H HLW. The entrained solvent concentration measured in the decontaminated salt solution (DSS) was as much as {approx}140 mg/L, although that value may be overstated by as much as 50% due to modifier solubility in the DSS. The entrained solvent concentration was measured in the strip effluent (SE) and the results are pending. A steady-state concentration factor (CF) of 15.9 was achieved with Tank 49H HLW. Cesium distribution ratios [D(Cs)] were measured with non-radioactive Tank 49H waste simulant and actual Tank 49H waste. Below is a comparison of D(Cs) values of ESS and 2-cm tests. Batch Extraction-Strip-Scrub (ESS) tests yielded D(Cs) values for extraction of {approx}81-88 for tests with Tank 49H waste and waste simulant. The results from the 2-cm contactor tests were in agreement with values of 58-92 for the Tank 49H HLW test and 54-83 for the simulant waste test. These values are consistent with the reference D(Cs) for extraction of {approx}60. In tests with Tank 49H waste and waste simulant, batch ESS tests measured D(Cs) values for the two scrub stages as {approx}3.5-5.0 for the first scrub stage and {approx}1.0-3.0 for the second scrub stage. In the Tank 49H test, the D(Cs) values for the 2-cm test were far from the ESS values. A D(Cs) value of 161 was measured for the first scrub stage and 10.8 for the second scrub stage. The data suggest that the scrub stage is not operating as effectively as intended. For the simulant test, a D(Cs) value of 1.9 was measured for the first scrub stage; the sample from the second scrub stage was compromised. Measurements of the pH of all stage samples for the Tank 49H test showed that the pH for extraction and scrub stages was 14 and the pH for the strip stages was {approx}7. It is expected that the pH of the second scrub stage would be {approx}12-13. Batch ESS tests measured D(Cs) values for the strip stages to be {approx}0.002-0.010. A high value in Strip No.3 of a test with simulant solution has been attributed to issues associated with the limits of detection for the analytical method. In the 2-cm contactor tests, the first four strip stages of the Tank 49H waste test and all five strip stages in the simulant waste test had higher values than the ESS tests. Only the fifth strip stage D(Cs) value of the Tank 49H waste test matched that of the ESS tests. It is speculated that the less-than-optimal performance of the strip section is caused by inefficiencies in the scrub section. Because strip is sensitive to pH, the elevated pH value in the second scrub stage may be the cause of strip performance. In spite of the D(Cs) values obtained in the scrub and strip sections, testing showed that the solvent system is robust. Average DFs for the process far exceeded targets even though the scrub and strip stages did not function optimally. Correction of the issue in the scrub and strip stages is expected to yield even higher waste DFs.« less

21 CFR 2.110 - Definition of ammonia under Federal Caustic Poison Act.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Definition of ammonia under Federal Caustic Poison... SERVICES GENERAL GENERAL ADMINISTRATIVE RULINGS AND DECISIONS Caustic Poisons § 2.110 Definition of ammonia under Federal Caustic Poison Act. For the purpose of determining whether an article containing ammonia...

21 CFR 2.110 - Definition of ammonia under Federal Caustic Poison Act.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 1 2013-04-01 2013-04-01 false Definition of ammonia under Federal Caustic Poison... SERVICES GENERAL GENERAL ADMINISTRATIVE RULINGS AND DECISIONS Caustic Poisons § 2.110 Definition of ammonia under Federal Caustic Poison Act. For the purpose of determining whether an article containing ammonia...

21 CFR 2.110 - Definition of ammonia under Federal Caustic Poison Act.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 1 2012-04-01 2012-04-01 false Definition of ammonia under Federal Caustic Poison... SERVICES GENERAL GENERAL ADMINISTRATIVE RULINGS AND DECISIONS Caustic Poisons § 2.110 Definition of ammonia under Federal Caustic Poison Act. For the purpose of determining whether an article containing ammonia...

21 CFR 2.110 - Definition of ammonia under Federal Caustic Poison Act.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 1 2014-04-01 2014-04-01 false Definition of ammonia under Federal Caustic Poison... SERVICES GENERAL GENERAL ADMINISTRATIVE RULINGS AND DECISIONS Caustic Poisons § 2.110 Definition of ammonia under Federal Caustic Poison Act. For the purpose of determining whether an article containing ammonia...

21 CFR 2.110 - Definition of ammonia under Federal Caustic Poison Act.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Definition of ammonia under Federal Caustic Poison... SERVICES GENERAL GENERAL ADMINISTRATIVE RULINGS AND DECISIONS Caustic Poisons § 2.110 Definition of ammonia under Federal Caustic Poison Act. For the purpose of determining whether an article containing ammonia...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jain, V.; Shah, H.; Bannochie, C. J.

Mercury (Hg) in the Savannah River Site Liquid Waste System (LWS) originated from decades of canyon processing where it was used as a catalyst for dissolving the aluminum cladding of reactor fuel. Approximately 60 metric tons of mercury is currently present throughout the LWS. Mercury has long been a consideration in the LWS, from both hazard and processing perspectives. In February 2015, a Mercury Program Team was established at the request of the Department of Energy to develop a comprehensive action plan for long-term management and removal of mercury. Evaluation was focused in two Phases. Phase I activities assessed themore » Liquid Waste inventory and chemical processing behavior using a system-by-system review methodology, and determined the speciation of the different mercury forms (Hg+, Hg++, elemental Hg, organomercury, and soluble versus insoluble mercury) within the LWS. Phase II activities are building on the Phase I activities, and results of the LWS flowsheet evaluations will be summarized in three reports: Mercury Behavior in the Salt Processing Flowsheet (i.e. this report); Mercury Behavior in the Defense Waste Processing Facility (DWPF) Flowsheet; and Mercury behavior in the Tank Farm Flowsheet (Evaporator Operations). The evaluation of the mercury behavior in the salt processing flowsheet indicates, inter alia, the following: (1) In the assembled Salt Batches 7, 8 and 9 in Tank 21, the total mercury is mostly soluble with methylmercury (MHg) contributing over 50% of the total mercury. Based on the analyses of samples from 2H Evaporator feed and drop tanks (Tanks 38/43), the source of MHg in Salt Batches 7, 8 and 9 can be attributed to the 2H evaporator concentrate used in assembling the salt batches. The 2H Evaporator is used to evaporate DWPF recycle water. (2) Comparison of data between Tank 21/49, Salt Solution Feed Tank (SSFT), Decontaminated Salt Solution Hold Tank (DSSHT), and Tank 50 samples suggests that the total mercury as well as speciated forms in the assembled salt batches in Tanks 21/49 pass through the Actinide Removal Process (ARP) / Modular Caustic Side Solvent Extraction Unit (MCU) process to Tank 50 with no significant change in the mercury chemistry. (3) In Tank 50, Decontaminated Salt Solution (DSS) from ARP/MCU is the major contributor to the total mercury including MHg. (4) Speciation analyses of TCLP leached solutions of the grout samples prepared from Tank 21, as well as Tank 50 samples, show the majority of the mercury released in the solution is MHg.« less

SOLIDS PRECIPITATION EVENT IN MCU CAUSAL ANALYSIS AND RECOMMENDATIONS FROM SOLIDS RECOVERY TEAM

DOE Office of Scientific and Technical Information (OSTI.GOV)

Garrison, A.; Aponte, C.

A process upset occurred in the Modular Caustic-Side Solvent Extraction Unit (MCU) facility on April 6th, 2014. During recovery efforts, a significant amount of solids were found in the Salt Solution Feed Tank (SSFT), Salt Solution Receipt Tanks (SSRTs), two extraction contactors, and scrub contactors. The solids were identified by Savannah River National Laboratory (SRNL) as primarily sodium oxalate and sodium alumina silicate (NAS) with the presence of some aluminum hydroxide. NAS solids have been present in the SSFT since simulant runs during cold chemical startup of MCU in 2007, and have not hindered operations since that time. During themore » process upset in April 2014, the oxalate solids partially blocked the aqueous outlet of the extraction contactors, causing salt solution to exit through the contactor organic outlet to the scrub contactors with the organic phase. This salt solution overwhelmed the scrub contactors and passed with the organic phase to the strip section of MCU. The partially reversed flow of salt solution resulted in a Strip Effluent (SE) stream that was high in Isopar™ L, pH and sodium. The primary cause of the excessive solids accumulation in the SSRTs and SSFT at MCU is attributed to an increase in the frequency of oxalic acid cleaning of the 512-S primary filter. Agitation in the SSRTs at MCU in response to cold weather likely provided the primary mechanism to transfer the solids to the contactors. Sources of the sodium oxalate solids are attributed to the oxalic acid cleaning solution used to clean the primary filter at the Actinide Removal Process (ARP) filtration at 512-S, as well as precipitation from the salt batch feed, which is at or near oxalate saturation. The Solids Recovery Team was formed to determine the cause of the solids formation and develop recommendations to prevent or mitigate this event in the future. A total of 53 recommendations were generated. These recommendations were organized into 4 focus areas: • Improve understanding of oxalate equilibrium and kinetics in salt solutions • Reduction/elimination of oxalic acid cleaning in 512-S • Flowsheet optimization • Improving diagnostic capability The recommendations implemented prior to resumption of MCU operations provide a risk mitigation or detection function through additional sampling and observation. The longer term recommendations provide a framework to increase the basic process knowledge of both oxalate chemistry and filtration behavior and then facilitate decisions that improve the salt flowsheet as a system.« less

Conformation of ionizable poly Para phenylene ethynylene in dilute solutions

DOE PAGES

Wijesinghe, Sidath; Maskey, Sabina; Perahia, Dvora; ...

2015-11-03

The conformation of dinonyl poly para phenylene ethynylenes (PPEs) with carboxylate side chains, equilibrated in solvents of different quality is studied using molecular dynamics simulations. PPEs are of interest because of their tunable electro-optical properties, chemical diversity, and functionality which are essential in wide range of applications. The polymer conformation determines the conjugation length and their assembly mode and affects electro-optical properties which are critical in their current and potential uses. The current study investigates the effect of carboxylate fraction on PPEs side chains on the conformation of chains in the dilute limit, in solvents of different quality. The dinonylmore » PPE chains are modeled atomistically, where the solvents are modeled both implicitly and explicitly. Dinonyl PPEs maintained a stretched out conformation up to a carboxylate fraction f of 0.7 in all solvents studied. The nonyl side chains are extended and oriented away from the PPE backbone in toluene and in implicit good solvent whereas in water and implicit poor solvent, the nonyl side chains are collapsed towards the PPE backbone. Thus, rotation around the aromatic ring is fast and no long range correlations are seen within the backbone.« less

Conformation of ionizable poly Para phenylene ethynylene in dilute solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wijesinghe, Sidath; Maskey, Sabina; Perahia, Dvora

The conformation of dinonyl poly para phenylene ethynylenes (PPEs) with carboxylate side chains, equilibrated in solvents of different quality is studied using molecular dynamics simulations. PPEs are of interest because of their tunable electro-optical properties, chemical diversity, and functionality which are essential in wide range of applications. The polymer conformation determines the conjugation length and their assembly mode and affects electro-optical properties which are critical in their current and potential uses. The current study investigates the effect of carboxylate fraction on PPEs side chains on the conformation of chains in the dilute limit, in solvents of different quality. The dinonylmore » PPE chains are modeled atomistically, where the solvents are modeled both implicitly and explicitly. Dinonyl PPEs maintained a stretched out conformation up to a carboxylate fraction f of 0.7 in all solvents studied. The nonyl side chains are extended and oriented away from the PPE backbone in toluene and in implicit good solvent whereas in water and implicit poor solvent, the nonyl side chains are collapsed towards the PPE backbone. Thus, rotation around the aromatic ring is fast and no long range correlations are seen within the backbone.« less

Rare earth elements recycling from waste phosphor by dual hydrochloric acid dissolution.

PubMed

Liu, Hu; Zhang, Shengen; Pan, Dean; Tian, Jianjun; Yang, Min; Wu, Maolin; Volinsky, Alex A

2014-05-15

This paper is a comparative study of recycling rare earth elements from waste phosphor, which focuses on the leaching rate and the technical principle. The traditional and dual dissolution by hydrochloric acid (DHA) methods were compared. The method of dual dissolution by hydrochloric acid has been developed. The Red rare earth phosphor (Y0.95Eu0.05)2O3 in waste phosphor is dissolved during the first step of acid leaching, while the Green phosphor (Ce0.67Tb0.33MgAl11O19) and the Blue phosphor (Ba0.9Eu0.1MgAl10O17) mixed with caustic soda are obtained by alkali sintering. The excess caustic soda and NaAlO2 are removed by washing. The insoluble matter is leached by the hydrochloric acid, followed by solvent extraction and precipitation (the DHA method). In comparison, the total leaching rate of the rare earth elements was 94.6% by DHA, which is much higher than 42.08% achieved by the traditional method. The leaching rate of Y, Eu, Ce and Tb reached 94.6%, 99.05%, 71.45%, and 76.22%, respectively. DHA can decrease the consumption of chemicals and energy. The suggested DHA method is feasible for industrial applications. Copyright © 2014 Elsevier B.V. All rights reserved.

Hazardous Waste Minimization Assessment: Fort Campbell, Kentucky

DTIC Science & Technology

1991-03-01

Used Oii - Better Operating Practices . Selective Segregation 97 Used Oil - Process Change - Fast Lube Oil Change System (FLOCS) 98 Caustic Wastes...Product Substitution 98 Caustic Wastes - Process Change - Hot Tank (Equipment) Modifications 98 Aqueous or Caustic Wastes - Process Change - Dry Ovens...Aqueous or Caustic Wastes - Equipment Leasiag 102 Dirty Rags/Uniforms • Onsite/Offsite Recycling - Laundry Service 103 Treatment 103 Used Oil - Onsite

Generation of Caustics and Rogue Waves from Nonlinear Instability.

PubMed

Safari, Akbar; Fickler, Robert; Padgett, Miles J; Boyd, Robert W

2017-11-17

Caustics are phenomena in which nature concentrates the energy of waves and may exhibit rogue-type behavior. Although they are known mostly in optics, caustics are intrinsic to all wave phenomena. As we demonstrate in this Letter, the formation of caustics and consequently rogue events in linear systems requires strong phase fluctuations. We show that nonlinear phase shifts can generate sharp caustics from even small fluctuations. Moreover, in that the wave amplitude increases dramatically in caustics, nonlinearity is usually inevitable. We perform an experiment in an optical system with Kerr nonlinearity, simulate the results based on the nonlinear Schrödinger equation, and achieve perfect agreement. As the same theoretical framework is used to describe other wave systems such as large-scale water waves, our results may also aid the understanding of ocean phenomena.

Generation of Caustics and Rogue Waves from Nonlinear Instability

NASA Astrophysics Data System (ADS)

Safari, Akbar; Fickler, Robert; Padgett, Miles J.; Boyd, Robert W.

2017-11-01

Caustics are phenomena in which nature concentrates the energy of waves and may exhibit rogue-type behavior. Although they are known mostly in optics, caustics are intrinsic to all wave phenomena. As we demonstrate in this Letter, the formation of caustics and consequently rogue events in linear systems requires strong phase fluctuations. We show that nonlinear phase shifts can generate sharp caustics from even small fluctuations. Moreover, in that the wave amplitude increases dramatically in caustics, nonlinearity is usually inevitable. We perform an experiment in an optical system with Kerr nonlinearity, simulate the results based on the nonlinear Schrödinger equation, and achieve perfect agreement. As the same theoretical framework is used to describe other wave systems such as large-scale water waves, our results may also aid the understanding of ocean phenomena.

Solvent polarity effects on supramolecular chirality of a polyfluorene-thiophene copolymer.

PubMed

Hirahara, Takashi; Yoshizawa-Fujita, Masahiro; Takeoka, Yuko; Rikukawa, Masahiro

2018-06-01

This study demonstrates the supramolecular chirality control of a conjugated polymer via solvent polarity. We designed and synthesized a chiral polyfluorene-thiophene copolymer having two different chiral side chains at the 9-position of the fluorene unit. Chiral cyclic and alkyl ethers with different polarities were selected as the chiral side chains. The sign of the circular dichroism spectra in the visible wavelength region was affected by the solvent system, resulting from the change of supramolecular structure. The estimation of the solubility parameter revealed that the solubility difference of the side chains contributed to the change of the circular dichroism sign, which was also observed in spin-coated films prepared from good solvents having different polarities. © 2018 Wiley Periodicals, Inc.

Cruise Report: Long-Range Ocean Acoustic Propagation EXperiment (LOAPEX)

DTIC Science & Technology

2005-04-01

starboard side was used. Both ends of the slip line shown ran through the crane hook to keep them vertical; a strip of masking tape was put around the...2150-3550 m nominal) with a 20-element, 700-in long array (3570- 4270 m nominal) to span the lower caustics in the acoustic arrival pattern with a...during the cruise. The critical equipment belonging to the ship included the stem A-frame, starboard A-frame, both of the ship’s cranes , CTD/rosette

Testing the Caustic Ring Dark Matter Halo Model Against Observations in the Milky Way

NASA Astrophysics Data System (ADS)

Dumas, Julie; Newberg, Heidi Jo; Niedzielski, Bethany; Susser, Adam; Thompson, Jeffery M.; Weiss, Jake; Lewis, Kim M.

2016-06-01

One prediction of axion dark matter models is they can form Bose-Einstein condensates and rigid caustic rings as a halo collapses in the non-linear regime. In this thesis, we undertake the first study of a caustic ring model for the Milky Way halo (Duffy & Sikivie 2008), paying particular attention to observational consequences. We first present the formalism for calculating the gravitational acceleration of a caustic ring halo. The caustic ring dark matter theory reproduces a roughly logarithmic halo, with large perturbations near the rings. We show that this halo can reasonably match the known Galactic rotation curve. We are not able to confirm or rule out an association between the positions of the caustic rings and oscillations in the observed rotation curve, due to insufficient rotation curve data. We explore the effects of dark matter caustic rings on dwarf galaxy tidal disruption with N-body simulations. Simulations of the Sagittarius (Sgr) dwarf galaxy in a caustic ring halo potential, with disk and bulge parameters that are tuned to match the Galactic rotation curve, match observations of the Sgr trailing tidal tails as far as 90 kpc from the Galactic center. Like the Navarro-Frenk-White (NFW) halo, they are, however, unable to match the leading tidal tail. None of the caustic, NFW, or triaxial logarithmic halos are able to simultaneously match observations of the leading and trailing arms of the Sagittarius stream. We further show that simulations of dwarf galaxies that move through caustic rings are qualitatively similar to those moving in a logarithmic halo. This research was funded by NSF grant AST 10-09670, the NASA-NY Space Grant, and the American Fellowship from AAUW.

A preliminary cost analysis of the biotreatment of refinery spent-sulfidic caustic.

PubMed

Sublette, K L

1997-01-01

Caustics are used in petroleum refining to remove hydrogen sulfide from various hydrocarbon streams. Spent-sulfidic caustics from three refineries have been successfully biotreated on the bench and pilot scale, resulting in neutralization and removal of active Sulfides. Sulfides were completely oxidized to sulfate by Thiobacillus denitrificans strain F. Microbial oxidation of sulfide produced acid, which at least partially neutralized the caustic. A commercial-scale treatment system has been designed that features a bioreactor with a suspended culture of flocculated T. denitrificans, a settler and acid and nutrient storage and delivery systems. A cost analysis has been performed for nine cases representing a range of spent caustic sulfide and hydroxide concentrations at a base treatment rate of 10 gpm. This analysis shows that refinery spent-sulfidic caustic can be biotreated for 4-8.3 cent/gal.

Gravitational lensing by ring-like structures

NASA Astrophysics Data System (ADS)

Lake, Ethan; Zheng, Zheng

2017-02-01

We study a class of gravitational lensing systems consisting of an inclined ring/belt, with and without an added point mass at the centre. We show that a common feature of such systems are so-called pseudo-caustics, across which the magnification of a point source changes discontinuously and yet remains finite. Such a magnification change can be associated with either a change in image multiplicity or a sudden change in the size of a lensed image. The existence of pseudo-caustics and the complex interplay between them and the formal caustics (which correspond to points of infinite magnification) can lead to interesting consequences, such as truncated or open caustics and a non-conservation of total image parity. The origin of the pseudo-caustics is found to be the non-differentiability of the solutions to the lens equation across the ring/belt boundaries, with the pseudo-caustics corresponding to ring/belt boundaries mapped into the source plane. We provide a few illustrative examples to understand the pseudo-caustic features, and in a separate paper consider a specific astronomical application of our results to study microlensing by extrasolar asteroid belts.

Structured caustic vector vortex optical field: manipulating optical angular momentum flux and polarization rotation.

PubMed

Chen, Rui-Pin; Chen, Zhaozhong; Chew, Khian-Hooi; Li, Pei-Gang; Yu, Zhongliang; Ding, Jianping; He, Sailing

2015-05-29

A caustic vector vortex optical field is experimentally generated and demonstrated by a caustic-based approach. The desired caustic with arbitrary acceleration trajectories, as well as the structured states of polarization (SoP) and vortex orders located in different positions in the field cross-section, is generated by imposing the corresponding spatial phase function in a vector vortex optical field. Our study reveals that different spin and orbital angular momentum flux distributions (including opposite directions) in different positions in the cross-section of a caustic vector vortex optical field can be dynamically managed during propagation by intentionally choosing the initial polarization and vortex topological charges, as a result of the modulation of the caustic phase. We find that the SoP in the field cross-section rotates during propagation due to the existence of the vortex. The unique structured feature of the caustic vector vortex optical field opens the possibility of multi-manipulation of optical angular momentum fluxes and SoP, leading to more complex manipulation of the optical field scenarios. Thus this approach further expands the functionality of an optical system.

68. INTERIOR VIEW LOOKING OF THE CAUSTIC SODA (SODIUM HYDROXIDE) ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

68. INTERIOR VIEW LOOKING OF THE CAUSTIC SODA (SODIUM HYDROXIDE) BUILDING, LOOKING AT CAUSTIC SODA MEASURING TANKS. (DATE UNKNOWN). - United States Nitrate Plant No. 2, Reservation Road, Muscle Shoals, Muscle Shoals, Colbert County, AL

Analytical caustic surfaces

NASA Technical Reports Server (NTRS)

Schmidt, R. F.

1987-01-01

This document discusses the determination of caustic surfaces in terms of rays, reflectors, and wavefronts. Analytical caustics are obtained as a family of lines, a set of points, and several types of equations for geometries encountered in optics and microwave applications. Standard methods of differential geometry are applied under different approaches: directly to reflector surfaces, and alternatively, to wavefronts, to obtain analytical caustics of two sheets or branches. Gauss/Seidel aberrations are introduced into the wavefront approach, forcing the retention of all three coefficients of both the first- and the second-fundamental forms of differential geometry. An existing method for obtaining caustic surfaces through exploitation of the singularities in flux density is examined, and several constant-intensity contour maps are developed using only the intrinsic Gaussian, mean, and normal curvatures of the reflector. Numerous references are provided for extending the material of the present document to the morphologies of caustics and their associated diffraction patterns.

Safety and licensing of a small modular gas-cooled reactor system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, N.W.; Kelley, A.P. Jr.

A modular side-by-side high-temperature gas-cooled reactor (SBS-HTGR) is being developed by Interatom/Kraftwerk Union (KWU). The General Electric Company and Interatom/KWU entered into a proprietary working agreement to continue develop jointly of the SBS-HTGR. A study on adapting the SBS-HTGR for application in the US has been completed. The study investigated the safety characteristics and the use of this type of design in an innovative approach to licensing. The safety objective guiding the design of the modular SBS-HTGR is to control radionuclide release by the retention of fission products within the fuel particles with minimal reliance on active design features. Themore » philosophy on which this objective is predicated is that by providing a simple safety case, the safety criteria can be demonstrated as being met with high confidence through conduct of a full-scale module safety test.« less

Causticizing for Black Liquor Gasifiers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott Sinquefeld; James Cantrell; Xiaoyan Zeng

2009-01-07

The cost-benefit outlook of black liquor gasification (BLG) could be greatly improved if the smelt causticization step could be achieved in situ during the gasification step. Or, at a minimum, the increase in causticizing load associated with BLG could be mitigated. A number of chemistries have been proven successful during black liquor combustion. In this project, three in situ causticizing processes (titanate, manganate, and borate) were evaluated under conditions suitable for high temperature entrained flow BLG, and low temperature steam reforming of black liquor. The evaluation included both thermodynamic modeling and lab experimentation. Titanate and manganate were tested for completemore » direct causticizing (to thus eliminate the lime cycle), and borates were evaluated for partial causticizing (to mitigate the load increase associated with BLG). Criteria included high carbonate conversion, corresponding hydroxide recovery upon hydrolysis, non process element (NPE) removal, and economics. Of the six cases (three chemistries at two BLG conditions), only two were found to be industrially viable: titanates for complete causticizing during high temperature BLG, and borates for partial causticizing during high temperature BLG. These two cases were evaluated for integration into a gasification-based recovery island. The Larsen [28] BLG cost-benefit study was used as a reference case for economic forecasting (i.e. a 1500 tpd pulp mill using BLG and upgrading the lime cycle). By comparison, using the titanate direct causticizing process yielded a net present value (NPV) of $25M over the NPV of BLG with conventional lime cycle. Using the existing lime cycle plus borate autocausticizing for extra capacity yielded a NPV of $16M.« less

Effects of Acids, Bases, and Heteroatoms on Proximal Radial Distribution Functions for Proteins.

PubMed

Nguyen, Bao Linh; Pettitt, B Montgomery

2015-04-14

The proximal distribution of water around proteins is a convenient method of quantifying solvation. We consider the effect of charged and sulfur-containing amino acid side-chain atoms on the proximal radial distribution function (pRDF) of water molecules around proteins using side-chain analogs. The pRDF represents the relative probability of finding any solvent molecule at a distance from the closest or surface perpendicular protein atom. We consider the near-neighbor distribution. Previously, pRDFs were shown to be universal descriptors of the water molecules around C, N, and O atom types across hundreds of globular proteins. Using averaged pRDFs, a solvent density around any globular protein can be reconstructed with controllable relative error. Solvent reconstruction using the additional information from charged amino acid side-chain atom types from both small models and protein averages reveals the effects of surface charge distribution on solvent density and improves the reconstruction errors relative to simulation. Solvent density reconstructions from the small-molecule models are as effective and less computationally demanding than reconstructions from full macromolecular models in reproducing preferred hydration sites and solvent density fluctuations.

Results from Alloy 600 And Alloy 690 Caustic SCC Model Boiler Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Frederick D.; Thomas, Larry E.

2009-08-03

A versatile model boiler test methodology was developed and used to compare caustic stress corrosion cracking (SCC) of mill annealed Alloy 600 and thermally treated Alloy 690. The model boiler included simulated crevice devices that efficiently and consistently concentrated Na2CO3, resulting in volatilization of CO2 with the steam and concentration of NaOH at the tube surfaces. The test methodology also included variation in tube stress, either produced by the primary to secondary side pressure differential, or by a novel method that reproducibly yields a higher stress condition on the tube. The significant effect of residual stress on tube SCC wasmore » also considered. SCC of both Alloy 600 and Alloy 690 were evaluated as a function of temperature and stress. Analytical transmission electron microscopy (ATEM) evaluations of the cracks and the grain boundaries ahead of the cracks were performed, providing insight into the SCC mechanism. This model boiler test methodology may be applicable to a range of bulkwater secondary chemistries that concentrate to produce aggressive crevice environments.« less

Evaluation and Management of Caustic Injuries from Ingestion of Acid or Alkaline Substances

PubMed Central

2014-01-01

Although the numbers have decreased compared with in the past, cases of patients who ingest caustic substances and visit the emergency room are not rare. However, well-summarized data about caustic injuries are insufficient. Therefore, in this article, I will discuss the etiologic causative agents, injury mechanism, and clinical characteristics, as well as the endoscopic evaluation of the degree of injury and proper management of the patient, in gastrointestinal caustic injury. PMID:25133115

Mid-Frequency Reverberation Measurements with Full Companion Environmental Support

DTIC Science & Technology

2014-12-30

it reaches a caustic . Beyond the caustic , it is only a saddle point [12]; there are distortions of the ray that give shorter travel times. Each of the...rays TBT, TB, and BT has at least one caustic . Thus, the argument must be modified. The following modified argument also uses Fermat’s prin- ciple...travel time decreased by about 1 ms. The presence of caustics invalidates a straightforward Fermat’s principle in- terpretation with a minimum travel

Optical caustics associated with the primary and the secondary rainbows of oblate droplets

NASA Astrophysics Data System (ADS)

Yu, Haitao; Shen, Jianqi; Tropea, Cameron

2014-08-01

The vector ray tracing (VRT) model is used to simulate the optical caustic structures near the primary and the secondary rainbow angles of oblate water droplets. The evolution process of the optical caustic structures in response to shape deformation of the water droplet is discussed. The dependence of the caustic structures on equatorial radius, refractive index and aspect ratio of the droplet are studied and the curvatures of the two rainbow fringes are calculated.

A modular approach to detection and identification of defects in rough lumber

Treesearch

Sang Mook Lee; A. Lynn Abbott; Daniel L. Schmoldt

2001-01-01

This paper describes a prototype scanning system that can automatically identify several important defects on rough hardwood lumber. The scanning system utilizes 3 laser sources and an embedded-processor camera to capture and analyze profile and gray-scale images. The modular approach combines the detection of wane (the curved sides of a board, possibly containing...

Modular Knowledge Representation and Reasoning in the Semantic Web

NASA Astrophysics Data System (ADS)

Serafini, Luciano; Homola, Martin

Construction of modular ontologies by combining different modules is becoming a necessity in ontology engineering in order to cope with the increasing complexity of the ontologies and the domains they represent. The modular ontology approach takes inspiration from software engineering, where modularization is a widely acknowledged feature. Distributed reasoning is the other side of the coin of modular ontologies: given an ontology comprising of a set of modules, it is desired to perform reasoning by combination of multiple reasoning processes performed locally on each of the modules. In the last ten years, a number of approaches for combining logics has been developed in order to formalize modular ontologies. In this chapter, we survey and compare the main formalisms for modular ontologies and distributed reasoning in the Semantic Web. We select four formalisms build on formal logical grounds of Description Logics: Distributed Description Logics, ℰ-connections, Package-based Description Logics and Integrated Distributed Description Logics. We concentrate on expressivity and distinctive modeling features of each framework. We also discuss reasoning capabilities of each framework.

Caustics for spherical waves

DOE PAGES

de Rham, Claudia; Motohashi, Hayato

2017-03-07

We study the development of caustics in shift-symmetric scalar field theories by focusing on simple waves with an S O ( p ) -symmetry in an arbitrary number of space dimensions. We show that the pure Galileon, the DBI–Galileon, and the extreme-relativistic Galileon naturally emerge as the unique set of caustic-free theories, highlighting a link between the caustic-free condition for simple S O ( p ) -waves and the existence of either a global Galilean symmetry or a global (extreme-)relativistic Galilean symmetry.

Optical method of caustics applied in viscoelastic fracture analysis

NASA Astrophysics Data System (ADS)

Gao, Guiyun; Li, Zheng; Xu, Jie

2011-05-01

The optical method of caustics is developed here to study the fracture of viscoelastic materials. By adopting a distribution of viscoelastic stress fields near the crack tip, the method of caustics is used to determine the viscoelastic fracture parameters from the caustic patterns near the crack tip. Two viscoelastic materials are studied. These are PMMA and ternary composites of HDPE/POE-g-MA/CaCO 3. The transmitted and reflective methods of caustics are performed separately to investigate viscoelastic fracture behaviors. The stress intensity factors (SIFs) versus time is determined by a series of shadow spot patterns combined with viscoelastic parameters evaluated by creep tests. In order to understand the viscoelastic fracture mechanisms of HDPE/POE-g-MA/CaCO 3 composites, their fracture surfaces are observed by a Scanning Electron Microscope (SEM). The results indicate that the method of caustics can be used to characterize the fracture behaviors of viscoelastic materials and further to optimize the design of polymer composites.

Analysis of sonic boom measurements near shock wave extremities for flight near Mach 1.0 and for airplane accelerations

NASA Technical Reports Server (NTRS)

Haglund, G. T.; Kane, E. J.

1974-01-01

The analysis of the 14 low-altitude transonic flights showed that the prevailing meteorological consideration of the acoustic disturbances below the cutoff altitude during threshold Mach number flight has shown that a theoretical safe altitude appears to be valid over a wide range of meteorological conditions and provides a reasonable estimate of the airplane ground speed reduction to avoid sonic boom noise during threshold Mach number flight. Recent theoretical results for the acoustic pressure waves below the threshold Mach number caustic showed excellent agreement with observations near the caustic, but the predicted overpressure levels were significantly lower than those observed far from the caustic. The analysis of caustics produced by inadvertent low-magnitude accelerations during flight at Mach numbers slightly greater than the threshold Mach number showed that folds and associated caustics were produced by slight changes in the airplane ground speed. These caustic intensities ranged from 1 to 3 time the nominal steady, level flight intensity.

Modular interdependency in complex dynamical systems.

PubMed

Watson, Richard A; Pollack, Jordan B

2005-01-01

Herbert A. Simon's characterization of modularity in dynamical systems describes subsystems as having dynamics that are approximately independent of those of other subsystems (in the short term). This fits with the general intuition that modules must, by definition, be approximately independent. In the evolution of complex systems, such modularity may enable subsystems to be modified and adapted independently of other subsystems, whereas in a nonmodular system, modifications to one part of the system may result in deleterious side effects elsewhere in the system. But this notion of modularity and its effect on evolvability is not well quantified and is rather simplistic. In particular, modularity need not imply that intermodule dependences are weak or unimportant. In dynamical systems this is acknowledged by Simon's suggestion that, in the long term, the dynamical behaviors of subsystems do interact with one another, albeit in an "aggregate" manner--but this kind of intermodule interaction is omitted in models of modularity for evolvability. In this brief discussion we seek to unify notions of modularity in dynamical systems with notions of how modularity affects evolvability. This leads to a quantifiable measure of modularity and a different understanding of its effect on evolvability.

Process Waste Assessment Machine and Fabrication Shop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phillips, N.M.

1993-03-01

This Process Waste Assessment was conducted to evaluate hazardous wastes generated in the Machine and Fabrication Shop at Sandia National Laboratories, Bonding 913, Room 119. Spent machine coolant is the major hazardous chemical waste generated in this facility. The volume of spent coolant generated is approximately 150 gallons/month. It is sent off-site to a recycler, but a reclaiming system for on-site use is being investigated. The Shop`s line management considers hazardous waste minimization very important. A number of steps have already been taken to minimize wastes, including replacement of a hazardous solvent with biodegradable, non-caustic solution and filtration unit; wastemore » segregation; restriction of beryllium-copper alloy machining; and reduction of lead usage.« less

Effects of Acids, Bases, and Heteroatoms on Proximal Radial Distribution Functions for Proteins

PubMed Central

Nguyen, Bao Linh; Pettitt, B. Montgomery

2015-01-01

The proximal distribution of water around proteins is a convenient method of quantifying solvation. We consider the effect of charged and sulfur-containing amino acid side-chain atoms on the proximal radial distribution function (pRDF) of water molecules around proteins using side-chain analogs. The pRDF represents the relative probability of finding any solvent molecule at a distance from the closest or surface perpendicular protein atom. We consider the near-neighbor distribution. Previously, pRDFs were shown to be universal descriptors of the water molecules around C, N, and O atom types across hundreds of globular proteins. Using averaged pRDFs, a solvent density around any globular protein can be reconstructed with controllable relative error. Solvent reconstruction using the additional information from charged amino acid side-chain atom types from both small models and protein averages reveals the effects of surface charge distribution on solvent density and improves the reconstruction errors relative to simulation. Solvent density reconstructions from the small-molecule models are as effective and less computationally demanding than reconstructions from full macromolecular models in reproducing preferred hydration sites and solvent density fluctuations. PMID:26388706

Underwater Rays

ERIC Educational Resources Information Center

Cepic, Mojca

2008-01-01

Light beams in wavy unclear water, also called underwater rays, and caustic networks of light formed at the bottom of shallow water are two faces of a single phenomenon. Derivation of the caustic using only simple geometry, Snell's law and simple derivatives accounts for observations such as the existence of the caustic network on vertical walls,…

21 CFR 1230.43 - Enforcement.

Code of Federal Regulations, 2011 CFR

2011-04-01

... CAUSTIC POISON ACT Imports § 1230.43 Enforcement. (a) Enforcement agency. The Federal Caustic Poison Act...) Enforcement of provisions. The enforcement of the provisions of the Federal Caustic Poison Act as they relate... Poison Act. (c) Chief of district as customs officer. The chief of district shall be deemed a customs...

21 CFR 1230.43 - Enforcement.

Code of Federal Regulations, 2014 CFR

2014-04-01

... CAUSTIC POISON ACT Imports § 1230.43 Enforcement. (a) Enforcement agency. The Federal Caustic Poison Act...) Enforcement of provisions. The enforcement of the provisions of the Federal Caustic Poison Act as they relate... Poison Act. (c) Chief of district as customs officer. The chief of district shall be deemed a customs...

21 CFR 1230.21 - Specific guaranty.

Code of Federal Regulations, 2012 CFR

2012-04-01

... FEDERAL CAUSTIC POISON ACT Guaranty § 1230.21 Specific guaranty. If a guaranty in respect to any specific... Caustic Poison Act. (Signature and address of guarantor) (b) Substances for other than household use (this... be misbranded within the meaning of the Federal Caustic Poison Act. (Name and address of manufacturer...

21 CFR 1230.21 - Specific guaranty.

Code of Federal Regulations, 2014 CFR

2014-04-01

... FEDERAL CAUSTIC POISON ACT Guaranty § 1230.21 Specific guaranty. If a guaranty in respect to any specific... Caustic Poison Act. (Signature and address of guarantor) (b) Substances for other than household use (this... be misbranded within the meaning of the Federal Caustic Poison Act. (Name and address of manufacturer...

21 CFR 1230.21 - Specific guaranty.

Code of Federal Regulations, 2010 CFR

2010-04-01

... FEDERAL CAUSTIC POISON ACT Guaranty § 1230.21 Specific guaranty. If a guaranty in respect to any specific... Caustic Poison Act. (Signature and address of guarantor) (b) Substances for other than household use (this... be misbranded within the meaning of the Federal Caustic Poison Act. (Name and address of manufacturer...

21 CFR 1230.43 - Enforcement.

Code of Federal Regulations, 2013 CFR

2013-04-01

... CAUSTIC POISON ACT Imports § 1230.43 Enforcement. (a) Enforcement agency. The Federal Caustic Poison Act...) Enforcement of provisions. The enforcement of the provisions of the Federal Caustic Poison Act as they relate... Poison Act. (c) Chief of district as customs officer. The chief of district shall be deemed a customs...

21 CFR 1230.21 - Specific guaranty.

Code of Federal Regulations, 2013 CFR

2013-04-01

... FEDERAL CAUSTIC POISON ACT Guaranty § 1230.21 Specific guaranty. If a guaranty in respect to any specific... Caustic Poison Act. (Signature and address of guarantor) (b) Substances for other than household use (this... be misbranded within the meaning of the Federal Caustic Poison Act. (Name and address of manufacturer...

21 CFR 1230.21 - Specific guaranty.

Code of Federal Regulations, 2011 CFR

2011-04-01

... FEDERAL CAUSTIC POISON ACT Guaranty § 1230.21 Specific guaranty. If a guaranty in respect to any specific... Caustic Poison Act. (Signature and address of guarantor) (b) Substances for other than household use (this... be misbranded within the meaning of the Federal Caustic Poison Act. (Name and address of manufacturer...

21 CFR 1230.43 - Enforcement.

Code of Federal Regulations, 2012 CFR

2012-04-01

... CAUSTIC POISON ACT Imports § 1230.43 Enforcement. (a) Enforcement agency. The Federal Caustic Poison Act...) Enforcement of provisions. The enforcement of the provisions of the Federal Caustic Poison Act as they relate... Poison Act. (c) Chief of district as customs officer. The chief of district shall be deemed a customs...

21 CFR 1230.43 - Enforcement.

Code of Federal Regulations, 2010 CFR

2010-04-01

... CAUSTIC POISON ACT Imports § 1230.43 Enforcement. (a) Enforcement agency. The Federal Caustic Poison Act...) Enforcement of provisions. The enforcement of the provisions of the Federal Caustic Poison Act as they relate... Poison Act. (c) Chief of district as customs officer. The chief of district shall be deemed a customs...

The internal caustic structure of illuminated liquid droplets

NASA Technical Reports Server (NTRS)

Lock, James A.; Hovenac, Edward A.

1991-01-01

The internal electric field of an illuminated liquid droplet is studied in detail using both wave theory and ray theory. The internal field obtains its maximum values on the caustics within the droplet. Ray theory is used to determine the equations of these caustics and the density of rays on them. The Debye series expansion of the interior field Mie amplitudes is used to calculate the wave theory version of these caustics. The physical interpretation of the sources of stimulated Raman scattering and fluorescence emission within a liquid droplet is then given.

CRITICAL CURVES AND CAUSTICS OF TRIPLE-LENS MODELS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daněk, Kamil; Heyrovský, David, E-mail: kamil.danek@utf.mff.cuni.cz, E-mail: heyrovsky@utf.mff.cuni.cz

2015-06-10

Among the 25 planetary systems detected up to now by gravitational microlensing, there are two cases of a star with two planets, and two cases of a binary star with a planet. Other, yet undetected types of triple lenses include triple stars or stars with a planet with a moon. The analysis and interpretation of such events is hindered by the lack of understanding of essential characteristics of triple lenses, such as their critical curves and caustics. We present here analytical and numerical methods for mapping the critical-curve topology and caustic cusp number in the parameter space of n-point-mass lenses.more » We apply the methods to the analysis of four symmetric triple-lens models, and obtain altogether 9 different critical-curve topologies and 32 caustic structures. While these results include various generic types, they represent just a subset of all possible triple-lens critical curves and caustics. Using the analyzed models, we demonstrate interesting features of triple lenses that do not occur in two-point-mass lenses. We show an example of a lens that cannot be described by the Chang–Refsdal model in the wide limit. In the close limit we demonstrate unusual structures of primary and secondary caustic loops, and explain the conditions for their occurrence. In the planetary limit we find that the presence of a planet may lead to a whole sequence of additional caustic metamorphoses. We show that a pair of planets may change the structure of the primary caustic even when placed far from their resonant position at the Einstein radius.« less

46 CFR Appendix I to Part 150 - Exceptions to the Chart

Code of Federal Regulations, 2013 CFR

2013-10-01

...). Triethylenetetramine (7). Sodium cresylate as Cresylate spent caustic (5) Methyl alcohol (20). Sodium dichromate, 70... (0) N-Methyl-2-pyrrolidone (9) Caustic potash, 50% or less (5) Isobutyl alcohol (20)Ethyl alcohol (20) Ethylene glycol (20) Isopropyl alcohol (20) Methyl alcohol (20) iso-Octyl alcohol (20) Caustic soda, 50% or...

46 CFR Appendix I to Part 150 - Exceptions to the Chart

Code of Federal Regulations, 2014 CFR

2014-10-01

...). Triethylenetetramine (7). Sodium cresylate as Cresylate spent caustic (5) Methyl alcohol (20). Sodium dichromate, 70...-pyrrolidone (9) Caustic potash, 50% or less (5) Isobutyl alcohol (20)Ethyl alcohol (20) Ethylene glycol (20) Isopropyl alcohol (20) Methyl alcohol (20) iso-Octyl alcohol (20) Caustic soda, 50% or less (5) Butyl...

16 CFR 1500.129 - Substances named in the Federal Caustic Poison Act.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Poison Act. 1500.129 Section 1500.129 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL... REGULATIONS § 1500.129 Substances named in the Federal Caustic Poison Act. The Commission finds that for those substances covered by the Federal Caustic Poison Act (44 Stat. 1406), the requirements of section 2(p)(1) of...

16 CFR 1500.129 - Substances named in the Federal Caustic Poison Act.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Poison Act. 1500.129 Section 1500.129 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL... REGULATIONS § 1500.129 Substances named in the Federal Caustic Poison Act. The Commission finds that for those substances covered by the Federal Caustic Poison Act (44 Stat. 1406), the requirements of section 2(p)(1) of...

16 CFR 1500.129 - Substances named in the Federal Caustic Poison Act.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Poison Act. 1500.129 Section 1500.129 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL... REGULATIONS § 1500.129 Substances named in the Federal Caustic Poison Act. The Commission finds that for those substances covered by the Federal Caustic Poison Act (44 Stat. 1406), the requirements of section 2(p)(1) of...

16 CFR § 1500.129 - Substances named in the Federal Caustic Poison Act.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Poison Act. § 1500.129 Section § 1500.129 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION... ENFORCEMENT REGULATIONS § 1500.129 Substances named in the Federal Caustic Poison Act. The Commission finds that for those substances covered by the Federal Caustic Poison Act (44 Stat. 1406), the requirements...

PEP Support: Laboratory Scale Leaching and Permeate Stability Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Renee L.; Peterson, Reid A.; Rinehart, Donald E.

2010-05-21

This report documents results from a variety of activities requested by the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The activities related to caustic leaching, oxidative leaching, permeate precipitation behavior of waste as well as chromium (Cr) leaching are: • Model Input Boehmite Leaching Tests • Pretreatment Engineering Platform (PEP) Support Leaching Tests • PEP Parallel Leaching Tests • Precipitation Study Results • Cr Caustic and Oxidative Leaching Tests. Leaching test activities using the PEP simulant provided input to a boehmite dissolution model and determined the effect of temperature on mass loss during caustic leaching, the reaction rate constantmore » for the boehmite dissolution, and the effect of aeration in enhancing the chromium dissolution during caustic leaching. Other tests were performed in parallel with the PEP tests to support the development of scaling factors for caustic and oxidative leaching. Another study determined if precipitate formed in the wash solution after the caustic leach in the PEP. Finally, the leaching characteristics of different chromium compounds under different conditions were examined to determine the best one to use in further testing.« less

Microbial oxidation of mixtures of methylmercaptan and hydrogen sulfide.

PubMed

Subramaniyan, A; Kolhatkar, R; Sublette, K L; Beitle, R

1998-01-01

Refinery spent-sulfidic caustic, containing only inorganic sulfides, has previously been shown to be amenable to biotreatment with Thiobacillus denitrificans strain F with complete oxidation of sulfides to sulfate. However, many spent caustics contain mercaptans that cannot be metabolized by this strict autotroph. An aerobic enrichment culture was developed from mixed Thiobacilli and activated sludge that was capable of simultaneous oxidation of inorganic sulfide and mercaptans using hydrogen sulfide (H2S) and methylmercaptan (MeSH) gas feeds used to simulate the inorganic and organic sulfur of a spent-sulfidic caustic. The enrichment culture was also capable of biotreatment of an actual mercaptan-containing, spent-sulfidic caustic but at lower rates than predicted by operation on MeSH and H2S fed to the culture in the gas phase, indicating that the caustic contained other inhibitory components.

Modular in situ-Functionalization Strategy: Multicomponent Polymerization via Palladium/Norbornene Cooperative Catalysis.

PubMed

Yoon, Ki-Young; Dong, Guangbin

2018-05-23

Herein, we report the palladium/norbornene cooperatively catalyzed polymerization, which simplifies synthesis of functional aromatic polymers, including conjugated polymers. Specifically, an A2B2C-type multicomponent polymerization is developed using ortho-amination/ipso-alkynylation reaction for preparing various amine-functionalized arylacetylene-containing polymers. Within a single catalytic cycle, the amine side-chains are site-selectively installed in situ via C-H activation during the polymerization process, which represents a major difference from conventional cross-coupling polymerizations. This in situ-functionalization strategy enables modular incorporation of functional side-chains from simple monomers, thereby conveniently affording a diverse range of functional polymers. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Portable and Lightweight Ramp Structure

DTIC Science & Technology

2001-04-09

long side of which is in abutting relationship with the 12 short side of the end of the ramp. Fastener receivers are equi- 13 spaced in duplicate...The modular sections are conveniently prefabricated 18 1 and provided in kit form to the number of sections corresponding 2 to the desired ramp

Hydrogen peroxide and caustic soda: Dancing with a dragon while bleaching

Treesearch

Peter W. Hart; Carl Houtman; Kolby Hirth

2013-01-01

When hydrogen peroxide is mixed with caustic soda, an auto-accelerating reaction can lead to generation of significant amounts of heat and oxygen. On the basis of experiments using typical pulp mill process concentration and temperatures, a relatively simple kinetic model has been developed. Evaluation of these model results reveals that hydrogen peroxide-caustic soda...

16 CFR 1500.129 - Substances named in the Federal Caustic Poison Act.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Commission therefore finds that for the following substances, and at the following concentrations, the word... REGULATIONS § 1500.129 Substances named in the Federal Caustic Poison Act. The Commission finds that for those... Caustic Poison Act, were required to bear the signal word “poison.” The Commission concludes that the lack...

OGLE-2016-BLG-1003: First Resolved Caustic-crossing Binary-source Event Discovered by Second-generation Microlensing Surveys

NASA Astrophysics Data System (ADS)

Jung, Y. K.; Udalski, A.; Bond, I. A.; Yee, J. C.; Gould, A.; Han, C.; Albrow, M. D.; Lee, C.-U.; Kim, S.-L.; Hwang, K.-H.; Chung, S.-J.; Ryu, Y.-H.; Shin, I.-G.; Zhu, W.; Cha, S.-M.; Kim, D.-J.; Lee, Y.; Park, B.-G.; Kim, H.-W.; Pogge, R. W.; KMTNet Collaboration; Skowron, J.; Szymański, M. K.; Poleski, R.; Mróz, P.; Kozłowski, S.; Pietrukowicz, P.; Soszyński, I.; Ulaczyk, K.; Pawlak, M.; OGLE Collaboration; Abe, F.; Bennett, D. P.; Barry, R.; Sumi, T.; Asakura, Y.; Bhattacharya, A.; Donachie, M.; Fukui, A.; Hirao, Y.; Itow, Y.; Koshimoto, N.; Li, M. C. A.; Ling, C. H.; Masuda, K.; Matsubara, Y.; Muraki, Y.; Nagakane, M.; Rattenbury, N. J.; Evans, P.; Sharan, A.; Sullivan, D. J.; Suzuki, D.; Tristram, P. J.; Yamada, T.; Yamada, T.; Yonehara, A.; MOA Collaboration

2017-06-01

We report the analysis of the first resolved caustic-crossing binary-source microlensing event OGLE-2016-BLG-1003. The event is densely covered by round-the-clock observations of three surveys. The light curve is characterized by two nested caustic-crossing features, which is unusual for typical caustic-crossing perturbations. From the modeling of the light curve, we find that the anomaly is produced by a binary source passing over a caustic formed by a binary lens. The result proves the importance of high-cadence and continuous observations, and the capability of second-generation microlensing experiments to identify such complex perturbations that are previously unknown. However, the result also raises the issues of the limitations of current analysis techniques for understanding lens systems beyond two masses and of determining the appropriate multiband observing strategy of survey experiments.

Effects of microstructure and mechanical properties of alloy 600 and 690 on secondary side SCC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vaillant, F.; Buisine, D.; Prieux, B.

1996-12-31

Modeling for secondary side cracking is needed to understand the behavior of alloy 600 in plants. They require a comprehensive understanding of the various influences of the material properties on Stress Corrosion Cracking (SCC), based on field experience and laboratory data. In an attempt to predict the materials effects on SCC behavior of new steam generators, laboratory corrosion data of alloy 690 were overviewed. French field experience with steam generators equipped with drilled tube support plates (TSPS) has demonstrated that the lower the yield stress (YS) and the carbon content, the higher the susceptibility to secondary side cracking of mill-annealedmore » (MA) alloy 600. Also heat treated (700 C x 16 h) tubing has been shown to have a much better resistance, but this excellent resistance could not be attributed only to the material properties. In laboratory environments, particularly in caustics, results have confirmed several of the above mentioned key findings on alloy 600.« less

Chemical Discovery as Belief Revision.

DTIC Science & Technology

1986-09-30

in order to explain conflicting experimental results. For example, Gay- Lussac and Thenard claimed that potassium con- sisted of caustic-potash and...hydrogen, while Davy observed that caustic-potash decomposed into potassium and oxygen. To support their view, Gay- Lussac and Thenard proposed that...Potash and Potassium We touched earlier on the disagreement between Davy and fellow chemists Gay- Lussac and Thenard concerning caustic-potash and

Test Results for Caustic Demand Measurements on Tank 241-AX-101 and Tank 241-AX-103 Archive Samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Doll, Stephanie R.; Bolling, Stacie D.

Caustic demand testing is used to determine the necessary amount of caustic required to neutralize species present in the Hanford tank waste and obtain a target molarity of free hydroxide for tank corrosion control. The presence and quantity of hydroxide-consuming analytes are just as important in determining the caustic demand as is the amount of free hydroxide present. No single data point can accurately predict whether a satisfactory hydroxide level is being met, as it is dependent on multiple factors (e.g., free hydroxide, buffers, amphoteric metal hydroxides, bicarbonate, etc.). This enclosure contains the caustic demand, scanning electron microscopy (SEM), polarizedmore » light microscopy (PLM), and X-ray diffraction (XRD) analysis for the tank 241-AX-101 (AX-101) and 241-AX-103 (AX-103) samples. The work was completed to fulfill a customer request outlined in the test plan, WRPS-1505529, “Test Plan and Procedure for Caustic Demand Testing on Tank 241-AX-101 and Tank 241-AX-103 Archive Samples.” The work results will provide a baseline to support planned retrieval of AX-101 and AX-103.« less

Caustic stress corrosion cracking of alloys 600 and 690 with NaOH concentrations

NASA Astrophysics Data System (ADS)

Park, In-Gyu; Lee, Chang-Soon; Hwang, Seong-Sik; Kim, Hong-Pyo; Kim, Joung-Soo

2005-10-01

In order to evaluate the stress corrosion cracking resistance for commercial alloys (C600MA, C600TT, C690TT) and Korean-made alloys (K600MA, K690TT), C-ring tests were performed in a caustic environment of 4, 10, 20, 30, and 50% NaOH solution at 315°C, for 480 h with an applied potential of 125 mV vs. OCP. Different stress corrosion cracking phenomena were observed according to the NaOH concentration. The rate of caustic IGSCC attack did not appear to increase monotonically with caustic concentrations, but peaked at a concentration between 4 and 50% caustic, or approximately 30% NaOH. Intergranular stress corrosion cracking was found for C600MA in 10, 20, and 30% NaOH solutions, while no cracking was observed in the 4 and 50% NaOH solutions. In 30% NaOH solution, transgrnular stress corrosion cracking was detected in C690TT, which may be related with the large amount of plastic strain (150% yield) and the applied potential (125 mV vs. OCP). The overall data clearly indicate that C600MA has the worst SCC resistance while K690TT offers the best resistance. There is also fairly good correlation between the caustic SCC susceptibility and some metallurgical parameters, particularly the grain size and the yield strength at room temperature. Specifically, materials having larger grain size and lower yield strength exhibited higher caustic SCC resistance.

Microlensing of Extremely Magnified Stars near Caustics of Galaxy Clusters

NASA Astrophysics Data System (ADS)

Venumadhav, Tejaswi; Dai, Liang; Miralda-Escudé, Jordi

2017-11-01

Recent observations of lensed galaxies at cosmological distances have detected individual stars that are extremely magnified when crossing the caustics of lensing clusters. In idealized cluster lenses with smooth mass distributions, two images of a star of radius R approaching a caustic brighten as {t}-1/2 and reach a peak magnification ˜ {10}6{(10{R}⊙ /R)}1/2 before merging on the critical curve. We show that a mass fraction ({κ }\\star ≳ {10}-4.5) in microlenses inevitably disrupts the smooth caustic into a network of corrugated microcaustics and produces light curves with numerous peaks. Using analytical calculations and numerical simulations, we derive the characteristic width of the network, caustic-crossing frequencies, and peak magnifications. For the lens parameters of a recent detection and a population of intracluster stars with {κ }\\star ˜ 0.01, we find a source-plane width of ˜ 20 {pc} for the caustic network, which spans 0.2 {arcsec} on the image plane. A source star takes ˜ 2× {10}4 years to cross this width, with a total of ˜ 6× {10}4 crossings, each one lasting for ˜ 5 {hr} (R/10 {R}⊙ ) with typical peak magnifications of ˜ {10}4 {(R/10{R}⊙ )}-1/2. The exquisite sensitivity of caustic-crossing events to the granularity of the lens-mass distribution makes them ideal probes of dark matter components, such as compact halo objects and ultralight axion dark matter.

Polymer Claw: Instant Underwater Adhesive

DTIC Science & Technology

2012-03-23

technology is the use of pressure sensitive microcapsules , which release reactive amine crosslinkers into an adhesive putty when pressed against the...PROIECT GOALS AND OBIECTIVES 2 2 KEY ACCOMPLISHMENTS 2 3.1 KICKOFF MEETING 3 3.2 AMINE MICROENCAPSULATION 3 3.3 CAUSTIC CLEANING AGENT 5 3.4...caustic, and the abrasive brush. We successfully synthesized amine-filled microcapsules and a dry mixture of caustic ingredients that only activate when

The point-characteristic function, wavefronts, and caustic of a spherical wave refracted by an arbitrary smooth surface.

PubMed

Marciano-Melchor, Magdalena; Navarro-Morales, Esperanza; Román-Hernández, Edwin; Santiago-Santiago, José Guadalupe; Silva-Ortigoza, Gilberto; Silva-Ortigoza, Ramón; Suárez-Xique, Román

2012-06-01

The aim of this paper is to obtain expressions for the k-function, the wavefront train, and the caustic associated with the light rays refracted by an arbitrary smooth surface after being emitted by a point light source located at an arbitrary position in a three-dimensional homogeneous optical medium. The general results are applied to a parabolic refracting surface. For this case, we find that when the point light source is off the optical axis, the caustic locally has singularities of the hyperbolic umbilic type, while the refracted wavefront, at the caustic region, locally has singularities of the cusp ridge and swallowtail types.

Specific and Modular Binding Code for Cytosine Recognition in Pumilio/FBF (PUF) RNA-binding Domains

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dong, Shuyun; Wang, Yang; Cassidy-Amstutz, Caleb

2011-10-28

Pumilio/fem-3 mRNA-binding factor (PUF) proteins possess a recognition code for bases A, U, and G, allowing designed RNA sequence specificity of their modular Pumilio (PUM) repeats. However, recognition side chains in a PUM repeat for cytosine are unknown. Here we report identification of a cytosine-recognition code by screening random amino acid combinations at conserved RNA recognition positions using a yeast three-hybrid system. This C-recognition code is specific and modular as specificity can be transferred to different positions in the RNA recognition sequence. A crystal structure of a modified PUF domain reveals specific contacts between an arginine side chain and themore » cytosine base. We applied the C-recognition code to design PUF domains that recognize targets with multiple cytosines and to generate engineered splicing factors that modulate alternative splicing. Finally, we identified a divergent yeast PUF protein, Nop9p, that may recognize natural target RNAs with cytosine. This work deepens our understanding of natural PUF protein target recognition and expands the ability to engineer PUF domains to recognize any RNA sequence.« less

46 CFR Table 151.05 to Subpart 151... - Summary of Minimum Requirements

Code of Federal Regulations, 2011 CFR

2011-10-01

...% or more Phenol, see Phenol Cresylate spent caustic Atmos. Amb. III 1 i i 2 i Integral Gravity Open... spent caustic Crotonaldehyde Atmos. Amb. II 1 i i 2 i i Integral Gravity PV Restr. II G-1 NR Vent F Yes.... II G-2 NR Vent N Yes .50-73 NA NA G Caustic potash solution Atmos. Amb.Elev. III 1 i 2 i Integral...

46 CFR Table 151.05 to Subpart 151... - Summary of Minimum Requirements

Code of Federal Regulations, 2014 CFR

2014-10-01

...% or more Phenol, see Phenol Cresylate spent caustic Atmos. Amb. III 1 i i 2 i Integral Gravity Open... spent caustic Crotonaldehyde Atmos. Amb. II 1 i i 2 i i Integral Gravity PV Restr. II G-1 NR Vent F Yes.... II G-2 NR Vent N Yes .50-73 NA NA G Caustic potash solution Atmos. Amb.Elev. III 1 i 2 i Integral...

46 CFR Table 151.05 to Subpart 151... - Summary of Minimum Requirements

Code of Federal Regulations, 2013 CFR

2013-10-01

...% or more Phenol, see Phenol Cresylate spent caustic Atmos. Amb. III 1 i i 2 i Integral Gravity Open... spent caustic Crotonaldehyde Atmos. Amb. II 1 i i 2 i i Integral Gravity PV Restr. II G-1 NR Vent F Yes.... II G-2 NR Vent N Yes .50-73 NA NA G Caustic potash solution Atmos. Amb.Elev. III 1 i 2 i Integral...

46 CFR Table 151.05 to Subpart 151... - Summary of Minimum Requirements

Code of Federal Regulations, 2010 CFR

2010-10-01

..., see Phenol Cresylate spent caustic Atmos. Amb. III 1 i i 2 i Integral Gravity Open Open II G-1 NR Vent N No .50-73.55-1(b) NA NA G Cresylic acid, sodium salt solution, see Cresylate spent caustic.... II G-2 NR Vent N Yes .50-73 NA NA G Caustic potash solution Atmos. Amb.Elev. III 1 i 2 i Integral...

46 CFR Table 151.05 to Subpart 151... - Summary of Minimum Requirements

Code of Federal Regulations, 2012 CFR

2012-10-01

...% or more Phenol, see Phenol Cresylate spent caustic Atmos. Amb. III 1 i i 2 i Integral Gravity Open... spent caustic Crotonaldehyde Atmos. Amb. II 1 i i 2 i i Integral Gravity PV Restr. II G-1 NR Vent F Yes... G-2 NR Vent N Yes .50-73 NA NA G Caustic potash solution Atmos. Amb.Elev. III 1 i 2 i Integral...

Results From The Salt Disposition Project Next Generation Solvent Demonstration Plan

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peters, T. B.; Fondeur, F. F.; Taylor-Pashow, K. M.L.

2014-04-02

Strip Effluent Hold Tank (SEHT), Decontaminated Salt Solution Hold Tank (DSSHT), Caustic Wash Tank (CWT) and Solvent Hold Tank (SHT) samples were taken throughout the Next Generation Solvent (NGS) Demonstration Plan. These samples were analyzed and the results are reported. SHT: The solvent behaved as expected, with no bulk changes in the composition over time, with the exception of the TOA and TiDG. The TiDG depletion is higher than expected, and consideration must be taken on the required rate of replenishment. Monthly sampling of the SHT is warranted. If possible, additional SHT samples for TiDG analysis (only) would help SRNLmore » refine the TiDG degradation model. CWT: The CWT samples show the expected behavior in terms of bulk chemistry. The 137Cs deposited into the CWT varies somewhat, but generally appears to be lower than during operations with the BOBCalix solvent. While a few minor organic components were noted to be present in the Preliminary sample, at this time these are thought to be artifacts of the sample preparation or may be due to the preceding solvent superwash. DSSHT: The DSSHT samples show the predicted bulk chemistry, although they point towards significant dilution at the front end of the Demonstration. The 137Cs levels in the DSSHT are much lower than during the BOBCalix operations, which is the expected observation. SEHT: The SEHT samples represent the most different output of all four of the outputs from MCU. While the bulk chemistry is as expected, something is causing the pH of the SEHT to be higher than what would be predicted from a pure stream of 0.01 M boric acid. There are several possible different reasons for this, and SRNL is in the process of investigating. Other than the pH issue, the SEHT is as predicted. In summary, the NGS Demonstration Plan samples indicate that the MCU system, with the Blend Solvent, is operating as expected. The only issue of concern regards the pH of the SEHT, and SRNL is in the process of investigating this. SRNL results support the transition to routine operations.« less

Solvent dielectric effect and side chain mutation on the structural stability of Burkholderia cepacia lipase active site: a quantum mechanical/molecular mechanics study.

PubMed

Tahan, A; Monajjemi, M

2011-12-01

Quantum mechanical and molecular dynamics methods were used to analyze the structure and stability of neutral and zwitterionic configurations of the extracted active site sequence from a Burkholderia cepacia lipase, histidyl-seryl-glutamin (His86-Ser87-Gln88) and its mutated form, histidyl-cysteyl-glutamin (His86-Cys87-Gln88) in vacuum and different solvents. The effects of solvent dielectric constant, explicit and implicit water molecules and side chain mutation on the structure and stability of this sequence in both neutral and zwitterionic forms are represented. The quantum mechanics computations represent that the relative stability of zwitterionic and neutral configurations depends on the solvent structure and its dielectric constant. Therefore, in vacuum and the considered non-polar solvents, the neutral form of the interested sequences is more stable than the zwitterionic form, while their zwitterionic form is more stable than the neutral form in the aqueous solution and the investigated polar solvents in most cases. However, on the potential energy surfaces calculated, there is a barrier to proton transfer from the positively charged ammonium group to the negatively charged carboxylat group or from the ammonium group to the adjacent carbonyl oxygen and or from side chain oxygen and sulfur to negatively charged carboxylat group. Molecular dynamics simulations (MD) were also performed by using periodic boundary conditions for the zwitterionic configuration of the hydrated molecules in a box of water molecules. The obtained results demonstrated that the presence of explicit water molecules provides the more compact structures of the studied molecules. These simulations also indicated that side chain mutation and replacement of sulfur with oxygen leads to reduction of molecular flexibility and packing.

Protective effects of dexpanthenol and y-27632 on stricture formation in a rat model of caustic esophageal injury.

PubMed

Ceylan, Haluk; Yapici, Sefa; Tutar, Ediz; Ceylan, Nurdan Ozlu; Tarakçıoğlu, Mehmet; Demiryurek, A Tuncay

2011-12-01

This experimental study was conducted to investigate the effect of dexpanthenol (converted in the body to pantothenic acid) and Y-27632 (a selective Rho-kinase inhibitor) on stricture formation after caustic (alkaline) esophageal injury in rats. Sixty male Wistar albino rats were randomly allocated into six groups. In group 1 (sham) the distal esophagus was isolated and cannulated but no caustic injury was induced. In all remaining groups, a caustic esophageal burn was induced with 50% sodium hydroxide solution for 90 s and drug treatment was given by daily intraperitoneal injection, beginning 24 h after injury and continuing for 21 d. In group 2 (controls), animals were treated with 0.9% saline; in groups 3 and 4, with 50 and 500 mg/kg/d of dexpanthenol, respectively; and in groups 5 and 6, with 0.3 and 3 mg/kg/d of Y-27632, respectively. Rats were sacrificed 22 d after caustic injury and the distal esophagus was isolated for histopathology and biochemical investigation. Stenosis index and collagen deposition scores were significantly lower in both the dexpanthenol and Y-27632 treated groups (P<0.05). Dexpanthenol and Y-27632 treatment markedly depressed esophageal tissue malondialdehyde and hydroxyproline levels. In this experimental model of caustic esophageal stricture, dexpanthenol and Y-27632 significantly attenuated esophageal stricture formation. These findings indicate that inhibition of Rho-kinase or dexpanthenol administration may offer novel therapeutic approaches in the treatment of caustic esophageal injury. Copyright © 2011 Elsevier Inc. All rights reserved.

A PLANETARY LENSING FEATURE IN CAUSTIC-CROSSING HIGH-MAGNIFICATION MICROLENSING EVENTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, Sun-Ju; Hwang, Kyu-Ha; Ryu, Yoon-Hyun

Current microlensing follow-up observations focus on high-magnification events because of the high efficiency of planet detection. However, central perturbations of high-magnification events caused by a planet can also be produced by a very close or a very wide binary companion, and the two kinds of central perturbations are not generally distinguished without time consuming detailed modeling (a planet-binary degeneracy). Hence, it is important to resolve the planet-binary degeneracy that occurs in high-magnification events. In this paper, we investigate caustic-crossing high-magnification events caused by a planet and a wide binary companion. From this investigation, we find that because of the differentmore » magnification excess patterns inside the central caustics induced by the planet and the binary companion, the light curves of the caustic-crossing planetary-lensing events exhibit a feature that is discriminated from those of the caustic-crossing binary-lensing events, and the feature can be used to immediately distinguish between the planetary and binary companions. The planetary-lensing feature appears in the interpeak region between the two peaks of the caustic-crossings. The structure of the interpeak region for the planetary-lensing events is smooth and convex or boxy, whereas the structure for the binary-lensing events is smooth and concave. We also investigate the effect of a finite background source star on the planetary-lensing feature in the caustic-crossing high-magnification events. From this, we find that the convex-shaped interpeak structure appears in a certain range that changes with the mass ratio of the planet to the planet-hosting star.« less

Oil refinery hazardous effluents minimization by membrane filtration: An on-site pilot plant study.

PubMed

Santos, Bruno; Crespo, João G; Santos, Maria António; Velizarov, Svetlozar

2016-10-01

Experiments for treating two different types of hazardous oil refinery effluents were performed in order to avoid/minimize their adverse impacts on the environment. First, refinery wastewater was subjected to ultrafiltration using a ceramic membrane, treatment, which did not provide an adequate reduction of the polar oil and grease content below the maximal contaminant level allowed. Therefore the option of reducing the polar oil and grease contamination at its main emission source point in the refinery - the spent caustic originating from the refinery kerosene caustic washing unit - using an alkaline-resistant nanofiltration polymeric membrane treatment was tested. It was found that at a constant operating pressure and temperature, 99.9% of the oil and grease and 97.7% of the COD content were rejected at this emission point. Moreover, no noticeable membrane fouling or permeate flux decrease were registered until a spent caustic volume concentration factor of 3. These results allow for a reuse of the purified permeate in the refinery operations, instead of a fresh caustic solution, which besides the improved safety and environmentally related benefits, can result in significant savings of 1.5 M€ per year at the current prices for the biggest Portuguese oil refinery. The capital investment needed for nanofiltration treatment of the spent caustic is estimated to be less than 10% of that associated with the conventional wet air oxidation treatment of the spent caustic that is greater than 9 M€. The payback period was estimated to be 1.1 years. The operating costs for the two treatment options are similar, but the reuse of the nanofiltration spent caustic concentrate for refinery pH control applications can further reduce the operating expenditures. Overall, the pilot plant results obtained and the process economics evaluation data indicate a safer, environmentally friendly and highly competitive solution offered by the proposed nanofiltration treatment, thus representing a promising alternative to the use of conventional spent caustic treatment units. Copyright © 2016 Elsevier Ltd. All rights reserved.

The wire optical test: a thorough analytical study in and out of caustic surface, and advantages of a dynamical adaptation

NASA Astrophysics Data System (ADS)

Alejandro Juárez-Reyes, Salvador; Sosa-Sánchez, Citlalli Teresa; Silva-Ortigoza, Gilberto; de Jesús Cabrera-Rosas, Omar; Espíndola-Ramos, Ernesto; Ortega-Vidals, Paula

2018-03-01

Among the best known non-interferometric optical tests are the wire test, the Foucault test and Ronchi test with a low frequency grating. Since the wire test is the seed to understand the other ones, the aim of the present work is to do a thorough study of this test for a lens with symmetry of revolution and to do this study for any configuration of the object and detection planes where both planes could intersect: two, one or no branches of the caustic region (including the marginal and paraxial foci). To this end, we calculated the vectorial representation for the caustic region, and we found the analytical expression for the pattern; we report that the analytical pattern explicitly depends on the magnitude of a branch of the caustic. With the analytical pattern we computed a set of simulations of a dynamical adaptation of the optical wire test. From those simulations, we have done a thorough analysis of the topological structure of the pattern; so we explain how the multiple image formation process and the image collapse process take place for each configuration, in particular, when both the wire and the detection planes are placed inside the caustic region, which has not been studied before. For the first time, we remark that not only the intersections of the object and detection planes with the caustic are important in the change of pattern topology; but also the projection of the intersection between the caustic and the object plane mapped onto the detection plane; and the virtual projection of the intersection between the caustic and the detection plane mapped onto the object plane. We present that for the new configurations of the optical system, the wire image is curves of the Tschirnhausen’s cubic, the piriform and the deformed eight-curve types.

A Modular PV System Using Chain-Link-Type Multilevel Converter

NASA Astrophysics Data System (ADS)

Hatano, Nobuhiko; Ise, Toshifumi

This paper presents a modular photovoltaic system (MPVS) that uses a chain-link-type multilevel converter (CLMC). In large-scale PV generating systems, the DC power supply is generally composed of a large number of PV panels. Hence, losses are caused by differences in the maximum power point at each PV panel. An MPVS has been proposed to address the above mentioned problem. It helps improve the photoelectric conversion efficiency by applying maximum power point tracking (MPPT) control to each group of PV panels. In addition, if a CLMC is used in an MPVS, a high voltage can be output from the AC side and transmission losses can be decreased. However, with this circuit configuration, the current output from the AC side may be unbalanced. Therefore, we propose a method to output balanced current from the AC side, even if the output of the DC power supply is unbalanced. The validity of the proposed method is examined by digital simulation.

Extreme Wave Statistics within the Mouth of the Columbia River

DTIC Science & Technology

2014-12-01

nearshore coastal environment. Because of his guidance, I was able to make the most of this challenging learning experience. I spent countless hours...the current field induces a refractive caustic along the principal current axis. Caustic focusing causes an increase of wave height to its maximum...the largest waves are found upstream of the caustic area (around x/Lo=25 in Figure 6). 10 Figure 6. Transformation of 0.1-Hz swell

Diffraction and Dissipation of Atmospheric Waves in the Vicinity of Caustics

NASA Astrophysics Data System (ADS)

Godin, O. A.

2015-12-01

A large and increasing number of ground-based and satellite-borne instruments has been demonstrated to reliably reveal ionospheric manifestations of natural hazards such as large earthquakes, strong tsunamis, and powerful tornadoes. To transition from detection of ionospheric manifestations of natural hazards to characterization of the hazards for the purposes of improving early warning systems and contributing to disaster recovery, it is necessary to relate quantitatively characteristics of the observed ionospheric disturbances and the underlying natural hazard and, in particular, accurately model propagation of atmospheric waves from the ground or ocean surface to the ionosphere. The ray theory has been used extensively to model propagation of atmospheric waves and proved to be very efficient in elucidating the effects of atmospheric variability on ionospheric signatures of natural hazards. However, the ray theory predicts unphysical, divergent values of the wave amplitude and needs to be modified in the vicinity of caustics. This paper presents an asymptotic theory that describes diffraction, focusing and increased dissipation of acoustic-gravity waves in the vicinity of caustics and turning points. Air temperature, viscosity, thermal conductivity, and wind velocity are assumed to vary gradually with height and horizontal coordinates, and slowness of these variations determines the large parameter of the problem. Uniform asymptotics of the wave field are expressed in terms of Airy functions and their derivatives. The geometrical, or Berry, phase, which arises in the consistent WKB approximation for acoustic-gravity waves, plays an important role in the caustic asymptotics. In addition to the wave field in the vicinity of the caustic, these asymptotics describe wave reflection from the caustic and the evanescent wave field beyond the caustic. The evanescent wave field is found to play an important role in ionospheric manifestations of tsunamis.

Environmental Review Guide for Operations (ERGO) - A Compliance Assessment Manual for Use at All USACE Civil-Funded Projects and Facilities

DTIC Science & Technology

1994-03-01

other Pickling liquor and other corrosive alkalies corrosive acids Lime wastewater Spent acid Lime and water Spent mixed acid Spent caustic Spent ...acid Spent caustic Spent sulfuric acid Potential Consequences: heat generation; violent reaction. 4 - 161 Appendix 4-6 (continued) Group 2-A Group 2-B1...topical bleach (STB) Ordnance, ammunition, explosives & residues Battery acid & caustics (in unserviceable batteries) Some pharmaceuticals Petroleum, oil

United States Air Force Shale Oil to Fuels. Phase II.

DTIC Science & Technology

1981-11-01

and modified so that any off-gas from the LPS, stripper column, product drums, spent caustic drums, and sample ports would be sent to the caustic ...product, or in the spent caustic . After the desalted Paraho shale oil was processed in Production Run No. 2, the catalyst bed was flushed with light cycle...58 20 First-Stage Hydrotreating of Occidental Shale Oil -- Spent Catalyst Analysis - Run 1 ....... 59 21 First-Stage Hydrotreating of Occidental

Caustics of 1/r{sup n} binary gravitational lenses: from galactic haloes to exotic matter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bozza, V.; Melchiorre, C., E-mail: valboz@physics.unisa.it, E-mail: cmelchiorre@unisa.it

2016-03-01

We investigate the caustic topologies for binary gravitational lenses made up of two objects whose gravitational potential declines as 1/r{sup n}. With n<1 this corresponds to power-law dust distributions like the singular isothermal sphere. The n>1 regime can be obtained with some violations of the energy conditions, one famous example being the Ellis wormhole. Gravitational lensing provides a natural arena to distinguish and identify such exotic objects in our Universe. We find that there are still three topologies for caustics as in the standard Schwarzschild binary lens, with the main novelty coming from the secondary caustics of the close topology,more » which become huge at higher n. After drawing caustics by numerical methods, we derive a large amount of analytical formulae in all limits that are useful to provide deeper insight in the mathematics of the problem. Our study is useful to better understand the phenomenology of galaxy lensing in clusters as well as the distinct signatures of exotic matter in complex systems.« less

Force Induced Globule-to-Coil Transition of Single Polymer Chains.

NASA Astrophysics Data System (ADS)

Gunari, Nikhil; Walker, Gilbert

2008-03-01

Force induced structural transitions of individual homopolymer chains have been studied in different solvent conditions using single molecule force spectroscopy. Single molecule mechanics in the ``fly-fishing'' mode showed a first-order like transition for polystyrene (PS) in water exhibiting a characteristic three regime force extension curve. In contrast, poly methylmethacrylate (PMMA) showed a characteristic saw-tooth pattern reminiscent of multidomain disassembly behavior similar to that seen in modular protein mechanics. The plateau force for PS and the saw-tooth pattern for PMMA disappear when measured in aqueous guanidine hydrochloride solution and in other non-solvents showing that the characteristic deformational behavior observed for the two polymers in water may be due to hydrophobic interactions .

Caustic Skeleton & Cosmic Web

NASA Astrophysics Data System (ADS)

Feldbrugge, Job; van de Weygaert, Rien; Hidding, Johan; Feldbrugge, Joost

2018-05-01

We present a general formalism for identifying the caustic structure of a dynamically evolving mass distribution, in an arbitrary dimensional space. The identification of caustics in fluids with Hamiltonian dynamics, viewed in Lagrangian space, corresponds to the classification of singularities in Lagrangian catastrophe theory. On the basis of this formalism we develop a theoretical framework for the dynamics of the formation of the cosmic web, and specifically those aspects that characterize its unique nature: its complex topological connectivity and multiscale spinal structure of sheetlike membranes, elongated filaments and compact cluster nodes. Given the collisionless nature of the gravitationally dominant dark matter component in the universe, the presented formalism entails an accurate description of the spatial organization of matter resulting from the gravitationally driven formation of cosmic structure. The present work represents a significant extension of the work by Arnol'd et al. [1], who classified the caustics that develop in one- and two-dimensional systems that evolve according to the Zel'dovich approximation. His seminal work established the defining role of emerging singularities in the formation of nonlinear structures in the universe. At the transition from the linear to nonlinear structure evolution, the first complex features emerge at locations where different fluid elements cross to establish multistream regions. Involving a complex folding of the 6-D sheetlike phase-space distribution, it manifests itself in the appearance of infinite density caustic features. The classification and characterization of these mass element foldings can be encapsulated in caustic conditions on the eigenvalue and eigenvector fields of the deformation tensor field. In this study we introduce an alternative and transparent proof for Lagrangian catastrophe theory. This facilitates the derivation of the caustic conditions for general Lagrangian fluids, with arbitrary dynamics. Most important in the present context is that it allows us to follow and describe the full three-dimensional geometric and topological complexity of the purely gravitationally evolving nonlinear cosmic matter field. While generic and statistical results can be based on the eigenvalue characteristics, one of our key findings is that of the significance of the eigenvector field of the deformation field for outlining the entire spatial structure of the caustic skeleton emerging from a primordial density field. In this paper we explicitly consider the caustic conditions for the three-dimensional Zel'dovich approximation, extending earlier work on those for one- and two-dimensional fluids towards the full spatial richness of the cosmic web. In an accompanying publication, we apply this towards a full three-dimensional study of caustics in the formation of the cosmic web and evaluate in how far it manages to outline and identify the intricate skeletal features in the corresponding N-body simulations.

Proceedings of the DICE THROW Symposium 21-23 June 1977. Volume 2

DTIC Science & Technology

1977-07-01

structure between 2.7 km and 4.3 km MSL that could cause distant blast focusing. Detailed acoustic ray calculations showed a caustic ring about 10 km...depending on just wheie the focus or caustic wave might strike. Propagation toward Truth or Consequences, MM, shown by Figure 14, was slightly ducted...layer. Thus there probably was no focus or caustic that struck any part of that small town. The recorded signal with 370-Pa amplitude was noisy

U S Navy Diving Manual. Volume 2. Mixed-Gas Diving. Revision 1.

DTIC Science & Technology

1981-07-01

has been soaked in a solution of portant aspects of underwater physics and physiology caustic potash. This chemical absorbed the carbon as they...between the diver’s breathing passages and the circuit must be of minimum volume minimum of caustic fumes. Water produced by the to preclude deadspace and...strongly react with water to pro- space around the absorbent bed to reduce the gas duce caustic fumes and cannot be used in UBA’s. flow distance. The

A Review of the Pollution Abatement Programs Relating to the Petroleum Refinery Industry in the Great Lakes Basin

DTIC Science & Technology

1982-11-01

of spent acids and caustics . The oil content of disposed wastes is 6,200 metric tons per year or approximately .01% of the average crude refinery rate...ALKYLATION "The major discharge from sulfuric acid alkylation are the spent caustics from the neutralization of hydrocarbon streams leaving the sulfuric... spent caustic waste stream. Any leaks or spills that involve loss of fluorides constitute a serious and difficult pollution problem. Formation of

21 CFR 1230.37 - Publication.

Code of Federal Regulations, 2010 CFR

2010-04-01

... CAUSTIC POISON ACT Administrative Procedures § 1230.37 Publication. (a) After judgment of the court in any proceeding under the Federal Caustic Poison Act, notice shall be given by publication. Such notice shall...

21 CFR 1230.37 - Publication.

Code of Federal Regulations, 2014 CFR

2014-04-01

... CAUSTIC POISON ACT Administrative Procedures § 1230.37 Publication. (a) After judgment of the court in any proceeding under the Federal Caustic Poison Act, notice shall be given by publication. Such notice shall...

21 CFR 1230.37 - Publication.

Code of Federal Regulations, 2012 CFR

2012-04-01

... CAUSTIC POISON ACT Administrative Procedures § 1230.37 Publication. (a) After judgment of the court in any proceeding under the Federal Caustic Poison Act, notice shall be given by publication. Such notice shall...

21 CFR 1230.37 - Publication.

Code of Federal Regulations, 2013 CFR

2013-04-01

... CAUSTIC POISON ACT Administrative Procedures § 1230.37 Publication. (a) After judgment of the court in any proceeding under the Federal Caustic Poison Act, notice shall be given by publication. Such notice shall...

21 CFR 1230.37 - Publication.

Code of Federal Regulations, 2011 CFR

2011-04-01

... CAUSTIC POISON ACT Administrative Procedures § 1230.37 Publication. (a) After judgment of the court in any proceeding under the Federal Caustic Poison Act, notice shall be given by publication. Such notice shall...

25. BUILDING NO. 527, DEHYDRATING HOUSE, DETAIL OF SOLVENT RECOVERY ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

25. BUILDING NO. 527, DEHYDRATING HOUSE, DETAIL OF SOLVENT RECOVERY DUCTS. SOUTH SIDE OF BUILDING. - Picatinny Arsenal, 500 Area, Powder Factory & Power House, State Route 15 near I-80, Dover, Morris County, NJ

21 CFR 1230.48 - Relabeling of containers.

Code of Federal Regulations, 2012 CFR

2012-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.48 Relabeling of containers. (a) If containers are to be... requirements of the Federal Caustic Poison Act and all regulations and instructions issued thereunder. The...

21 CFR 1230.48 - Relabeling of containers.

Code of Federal Regulations, 2011 CFR

2011-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.48 Relabeling of containers. (a) If containers are to be... requirements of the Federal Caustic Poison Act and all regulations and instructions issued thereunder. The...

21 CFR 1230.48 - Relabeling of containers.

Code of Federal Regulations, 2013 CFR

2013-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.48 Relabeling of containers. (a) If containers are to be... requirements of the Federal Caustic Poison Act and all regulations and instructions issued thereunder. The...

21 CFR 1230.48 - Relabeling of containers.

Code of Federal Regulations, 2010 CFR

2010-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.48 Relabeling of containers. (a) If containers are to be... requirements of the Federal Caustic Poison Act and all regulations and instructions issued thereunder. The...

21 CFR 1230.48 - Relabeling of containers.

Code of Federal Regulations, 2014 CFR

2014-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.48 Relabeling of containers. (a) If containers are to be... requirements of the Federal Caustic Poison Act and all regulations and instructions issued thereunder. The...

Comparing side chain packing in soluble proteins, protein-protein interfaces, and transmembrane proteins.

PubMed

Gaines, J C; Acebes, S; Virrueta, A; Butler, M; Regan, L; O'Hern, C S

2018-05-01

We compare side chain prediction and packing of core and non-core regions of soluble proteins, protein-protein interfaces, and transmembrane proteins. We first identified or created comparable databases of high-resolution crystal structures of these 3 protein classes. We show that the solvent-inaccessible cores of the 3 classes of proteins are equally densely packed. As a result, the side chains of core residues at protein-protein interfaces and in the membrane-exposed regions of transmembrane proteins can be predicted by the hard-sphere plus stereochemical constraint model with the same high prediction accuracies (>90%) as core residues in soluble proteins. We also find that for all 3 classes of proteins, as one moves away from the solvent-inaccessible core, the packing fraction decreases as the solvent accessibility increases. However, the side chain predictability remains high (80% within 30°) up to a relative solvent accessibility, rSASA≲0.3, for all 3 protein classes. Our results show that ≈40% of the interface regions in protein complexes are "core", that is, densely packed with side chain conformations that can be accurately predicted using the hard-sphere model. We propose packing fraction as a metric that can be used to distinguish real protein-protein interactions from designed, non-binding, decoys. Our results also show that cores of membrane proteins are the same as cores of soluble proteins. Thus, the computational methods we are developing for the analysis of the effect of hydrophobic core mutations in soluble proteins will be equally applicable to analyses of mutations in membrane proteins. © 2018 Wiley Periodicals, Inc.

27 CFR 21.63 - Formula No. 36.

Code of Federal Regulations, 2012 CFR

2012-04-01

... pounds of caustic soda, liquid grade, containing 50 percent sodium hydroxide by weight; or 12.0 pounds of caustic soda, liquid grade, containing 73 percent sodium hydroxide by weight. (b) Authorized uses. (1) As...

27 CFR 21.63 - Formula No. 36.

Code of Federal Regulations, 2014 CFR

2014-04-01

... pounds of caustic soda, liquid grade, containing 50 percent sodium hydroxide by weight; or 12.0 pounds of caustic soda, liquid grade, containing 73 percent sodium hydroxide by weight. (b) Authorized uses. (1) As...

27 CFR 21.63 - Formula No. 36.

Code of Federal Regulations, 2013 CFR

2013-04-01

... pounds of caustic soda, liquid grade, containing 50 percent sodium hydroxide by weight; or 12.0 pounds of caustic soda, liquid grade, containing 73 percent sodium hydroxide by weight. (b) Authorized uses. (1) As...

Determination of terpenoid content in pine by organic solvent extraction and fast-GC analysis

DOE PAGES

Harman-Ware, Anne E.; Sykes, Robert; Peter, Gary F.; ...

2016-01-25

Terpenoids, naturally occurring compounds derived from isoprene units present in pine oleoresin, are a valuable source of chemicals used in solvents, fragrances, flavors, and have shown potential use as a biofuel. This paper describes a method to extract and analyze the terpenoids present in loblolly pine saplings and pine lighter wood. Various extraction solvents were tested over different times and temperatures. Samples were analyzed by pyrolysis-molecular beam mass spectrometry before and after extractions to monitor the extraction efficiency. The pyrolysis studies indicated that the optimal extraction method used a 1:1 hexane/acetone solvent system at 22°C for 1 h. Extracts frommore » the hexane/acetone experiments were analyzed using a low thermal mass modular accelerated column heater for fast-GC/FID analysis. The most abundant terpenoids from the pine samples were quantified, using standard curves, and included the monoterpenes, α- and β-pinene, camphene, and δ-carene. Sesquiterpenes analyzed included caryophyllene, humulene, and α-bisabolene. In conclusion, diterpenoid resin acids were quantified in derivatized extractions, including pimaric, isopimaric, levopimaric, palustric, dehydroabietic, abietic, and neoabietic acids.« less

Potentials of biological oxidation processes for the treatment of spent sulfidic caustics containing thiols.

PubMed

Sipma, Jan; Svitelskaya, Anna; van der Mark, Bart; Pol, Look W Hulshoff; Lettinga, Gatze; Buisman, Cees J N; Janssen, Albert J H

2004-12-01

This research focused on the biological treatment of sulfidic spent caustics from refineries, which contain mainly hydrogen sulfide, methanethiol (MT) and ethanethiol (ET). Also various organic compounds can be present such as BTEX. Biological oxidation of 2.5 mM MT in batch experiments occurred after MT was first auto-oxidized into dimethyldisulfide (DMDS) whereafter oxidation into sulfate was completed in 350 h. DMDS as sole substrate was completely oxidized within 40 h. Therefore, DMDS formation seems to play an important role in detoxification of MT. Biological oxidation of ET and buthanethiol was not successful in batch experiments. Complete oxidation of MT and ET was observed in flow-through reactor experiments. Simultaneous oxidation of sulfide and MT was achieved when treating a synthetic spent caustic, containing 10 mM sulfide and 2.5 mM MT, in a bubble column reactor with carrier material at a hydraulic retention time of 6 h. Addition of 7.5 mM phenol, a common pollutant of spent caustics, did not adversely affect the biological oxidation process and phenol was completely removed from the effluent. Finally, three different spent caustics solutions from refineries were successfully treated.

21 CFR 1230.40 - Required label information.

Code of Federal Regulations, 2010 CFR

2010-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.40 Required label information. Containers which are offered for...) (1), (2), and (3) of the Federal Caustic Poison Act and the directions for treatment in the case of...

21 CFR 1230.40 - Required label information.

Code of Federal Regulations, 2012 CFR

2012-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.40 Required label information. Containers which are offered for...) (1), (2), and (3) of the Federal Caustic Poison Act and the directions for treatment in the case of...

21 CFR 1230.40 - Required label information.

Code of Federal Regulations, 2014 CFR

2014-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.40 Required label information. Containers which are offered for...) (1), (2), and (3) of the Federal Caustic Poison Act and the directions for treatment in the case of...

21 CFR 1230.40 - Required label information.

Code of Federal Regulations, 2011 CFR

2011-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.40 Required label information. Containers which are offered for...) (1), (2), and (3) of the Federal Caustic Poison Act and the directions for treatment in the case of...

21 CFR 1230.40 - Required label information.

Code of Federal Regulations, 2013 CFR

2013-04-01

... FEDERAL CAUSTIC POISON ACT Imports § 1230.40 Required label information. Containers which are offered for...) (1), (2), and (3) of the Federal Caustic Poison Act and the directions for treatment in the case of...

Observation of the enhanced backscattering of light by the end of a tilted dielectric cylinder owing to the caustic merging transition

NASA Astrophysics Data System (ADS)

Marston, Philip L.; Zhang, Yibing; Thiessen, David B.

2003-01-01

The scattering of light by obliquely illuminated circular dielectric cylinders was previously demonstrated to be enhanced by a merger of Airy caustics at a critical tilt angle. [Appl. Opt. 37, 1534 (1998)]. A related enhancement is demonstrated here for backward and near-backward scattering for cylinders cut with a flat end perpendicular to the cylinder's axis. It is expected that merged caustics will enhance the backscattering by clouds of randomly oriented circular cylinders that have appropriately flat ends.

A Technique for Evaluating the Uncertainties in Path Loss Predictions Caused by Sparsely Sampled Terrain Data

DTIC Science & Technology

2013-06-26

Diomedi, thank you for providing support in getting through the writing. To my parents and Suzanne’s, thank you for tolerating the time we’ve spent here...the caustic distance idea from geometric optics, and will be shown to slightly improve the results. Following those results, antenna patterns will be...change in the caustic in the 3rd dimension, while MOMI has already accounted for it in the x-z plane. In geometric optics, the caustic is the point of

Chemical Modification of Cellulose Esters for Oral Drug Delivery

NASA Astrophysics Data System (ADS)

Meng, Xiangtao

Polymer functional groups have critical impacts upon physical, chemical and mechanical properties, and thus affect the specific applications of the polymer. Functionalization of cellulose esters and ethers has been under extensive investigation for applications including drug delivery, cosmetics, food ingredients, and automobile coating. In oral delivery of poorly water-soluble drugs, amorphous solid dispersion (ASD) formulations have been used, prepared by forming miscible blends of polymers and drugs to inhibit crystallization and enhance bioavailability of the drug. The Edgar and Taylor groups have revealed that some cellulose o-carboxyalkanoates were highly effective as ASD polymers, with the pendant carboxylic acid groups providing both specific polymer-drug interactions and pHtriggered release through swelling of the ionized polymer matrix. While a variety of functional groups such as hydroxyl and amide groups are also of interest, cellulose functionalization has relied heavily on classical methods such as esterification and etherification for appending functional groups. These methods, although they have been very useful, are limited in two respects. First, they typically employ harsh reaction conditions. Secondly, each synthetic pathway is only applicable for one or a narrow group of functionalities due to restrictions imposed by the required reaction conditions. To this end, there is a great impetus to identify novel reactions in cellulose modification that are mild, efficient and ideally modular. In the initial effort to design and synthesize cellulose esters for oral drug delivery, we developed several new methods in cellulose functionalization, which can overcome drawbacks of conventional synthetic pathways, provide novel cellulose derivatives that are otherwise inaccessible, and present a platform for structure-property relationship study. Cellulose o-hydroxyalkanoates were previously difficult to access as the hydroxyl groups, if not protected, react with carboxylic acid/carbonyl during a typical esterification reaction or ring opening of lactones, producing cellulose-g-polyester and homopolyester. We demonstrated the viability of chemoselective olefin hydroboration-oxidation in the synthesis of cellulose o-hydroxyesters in the presence of ester groups. Cellulose esters with terminally olefinic side chains were transformed to the target products by two-step, one-pot hydroborationoxidation reactions, using 9-borabicyclo[3.3.1]nonane (9-BBN) as hydroboration agent, followed by oxidizing the organoborane intermediate to a primary alcohol using mildly alkaline H2O2. The use of 9-BBN as hydroboration agent and sodium acetate as base catalyst in oxidation successfully avoided cleavage of ester linkages by borane reduction and base catalyzed hydrolysis. With the impetus of modular and efficient synthesis, we introduced olefin crossmetathesis (CM) in polysaccharide functionalization. Using Grubbs type catalyst, cellulose esters with terminally olefinic side chains were reacted with various CM partners including acrylic acid, acrylates and acrylamides to afford families of functionalized cellulose esters. Molar excesses of CM partners were used in order to suppress potential crosslinking caused by self-metathesis between terminally olefinic side chains. Amide CM partners can chelate with the ruthenium catalyst and cause low conversions in conventional solvents such as THF. While the inherent reactivity toward CM and tendency of acrylamides to chelate Ru is influenced by the acrylamide N-substituents, employing acetic acid as a solvent significantly improved the conversion of certain acrylamides. We observed that the CM products are prone to crosslinking during storage, and found that the crosslinking is likely caused by free radical abstraction of gamma-hydrogen of the alpha,beta-unsaturation and subsequent recombination. We further demonstrated successful hydrogenation of these alpha,beta-unsaturated acids, esters, and amides, thereby eliminating the potential for radical-induced crosslinking during storage. The alpha,beta-unsaturation on CM products can cause crosslinking due to gamma-H abstraction and recombination if not reduced immediately after reaction. Instead of eliminating the double bond by hydrogenation, we described a method to make use of these reactive conjugated olefins by post-CM thiol-Michael addition. Under amine catalysis, different CM products and thiols were combined and reacted. Using proper thiols and catalyst, complete conversion can be achieved under mild reaction conditions. The combination of the two modular reactions creates versatile access to multi-functionalized cellulose derivatives. Compared with conventional reactions, these reactions enable click or click-like conjugation of functional groups onto cellulose backbone. The modular profile of the reactions enables clean and informative structure-property relationship studies for ASD. These approaches also provide opportunities for the synthesis of chemically and architecturally diverse cellulosic polymers that are otherwise difficult to access, opening doors for many other applications such as antimicrobial, antifouling, in vivo drug delivery, and bioconjugation. We believe that the cellulose functionalization approaches we pioneered can be expanded to the modification of other polysaccharides and polymers, and that these reactions will become useful tools in the toolbox of polymer/polysaccharide chemists.

Monitoring caustic injuries from emergency department databases using automatic keyword recognition software.

PubMed

Vignally, P; Fondi, G; Taggi, F; Pitidis, A

2011-03-31

In Italy the European Union Injury Database reports the involvement of chemical products in 0.9% of home and leisure accidents. The Emergency Department registry on domestic accidents in Italy and the Poison Control Centres record that 90% of cases of exposure to toxic substances occur in the home. It is not rare for the effects of chemical agents to be observed in hospitals, with a high potential risk of damage - the rate of this cause of hospital admission is double the domestic injury average. The aim of this study was to monitor the effects of injuries caused by caustic agents in Italy using automatic free-text recognition in Emergency Department medical databases. We created a Stata software program to automatically identify caustic or corrosive injury cases using an agent-specific list of keywords. We focused attention on the procedure's sensitivity and specificity. Ten hospitals in six regions of Italy participated in the study. The program identified 112 cases of injury by caustic or corrosive agents. Checking the cases by quality controls (based on manual reading of ED reports), we assessed 99 cases as true positive, i.e. 88.4% of the patients were automatically recognized by the software as being affected by caustic substances (99% CI: 80.6%- 96.2%), that is to say 0.59% (99% CI: 0.45%-0.76%) of the whole sample of home injuries, a value almost three times as high as that expected (p < 0.0001) from European codified information. False positives were 11.6% of the recognized cases (99% CI: 5.1%- 21.5%). Our automatic procedure for caustic agent identification proved to have excellent product recognition capacity with an acceptable level of excess sensitivity. Contrary to our a priori hypothesis, the automatic recognition system provided a level of identification of agents possessing caustic effects that was significantly much greater than was predictable on the basis of the values from current codifications reported in the European Database.

Engineering modular ester fermentative pathways in Escherichia coli.

PubMed

Layton, Donovan S; Trinh, Cong T

2014-11-01

Sensation profiles are observed all around us and are made up of many different molecules, such as esters. These profiles can be mimicked in everyday items for their uses in foods, beverages, cosmetics, perfumes, solvents, and biofuels. Here, we developed a systematic 'natural' way to derive these products via fermentative biosynthesis. Each ester fermentative pathway was designed as an exchangeable ester production module for generating two precursors- alcohols and acyl-CoAs that were condensed by an alcohol acyltransferase to produce a combinatorial library of unique esters. As a proof-of-principle, we coupled these ester modules with an engineered, modular, Escherichia coli chassis in a plug-and-play fashion to create microbial cell factories for enhanced anaerobic production of a butyrate ester library. We demonstrated tight coupling between the modular chassis and ester modules for enhanced product biosynthesis, an engineered phenotype useful for directed metabolic pathway evolution. Compared to the wildtype, the engineered cell factories yielded up to 48 fold increase in butyrate ester production from glucose. Copyright © 2014 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

21 CFR 1230.36 - Hearings; when not provided for.

Code of Federal Regulations, 2011 CFR

2011-04-01

... FEDERAL CAUSTIC POISON ACT Administrative Procedures § 1230.36 Hearings; when not provided for. No hearing... Caustic Poison Act (44 Stat. 1409; 15 U.S.C. 408) in reporting a violation direct to the United States...

21 CFR 1230.36 - Hearings; when not provided for.

Code of Federal Regulations, 2013 CFR

2013-04-01

... FEDERAL CAUSTIC POISON ACT Administrative Procedures § 1230.36 Hearings; when not provided for. No hearing... Caustic Poison Act (44 Stat. 1409; 15 U.S.C. 408) in reporting a violation direct to the United States...

21 CFR 1230.36 - Hearings; when not provided for.

Code of Federal Regulations, 2010 CFR

2010-04-01

... FEDERAL CAUSTIC POISON ACT Administrative Procedures § 1230.36 Hearings; when not provided for. No hearing... Caustic Poison Act (44 Stat. 1409; 15 U.S.C. 408) in reporting a violation direct to the United States...

21 CFR 1230.36 - Hearings; when not provided for.

Code of Federal Regulations, 2014 CFR

2014-04-01

... FEDERAL CAUSTIC POISON ACT Administrative Procedures § 1230.36 Hearings; when not provided for. No hearing... Caustic Poison Act (44 Stat. 1409; 15 U.S.C. 408) in reporting a violation direct to the United States...

21 CFR 1230.36 - Hearings; when not provided for.

Code of Federal Regulations, 2012 CFR

2012-04-01

... FEDERAL CAUSTIC POISON ACT Administrative Procedures § 1230.36 Hearings; when not provided for. No hearing... Caustic Poison Act (44 Stat. 1409; 15 U.S.C. 408) in reporting a violation direct to the United States...

Microlensing as a possible probe of event-horizon structure in quasars

NASA Astrophysics Data System (ADS)

Tomozeiu, Mihai; Mohammed, Irshad; Rabold, Manuel; Saha, Prasenjit; Wambsganss, Joachim

2018-04-01

In quasars which are lensed by galaxies, the point-like images sometimes show sharp and uncorrelated brightness variations (microlensing). These brightness changes are associated with the innermost region of the quasar passing through a complicated pattern of caustics produced by the stars in the lensing galaxy. In this paper, we study whether the universal properties of optical caustics could enable extraction of shape information about the central engine of quasars. We present a toy model with a crescent-shaped source crossing a fold caustic. The silhouette of a black hole over an accretion disc tends to produce roughly crescent sources. When a crescent-shaped source crosses a fold caustic, the resulting light curve is noticeably different from the case of a circular luminosity profile or Gaussian source. With good enough monitoring data, the crescent parameters, apart from one degeneracy, can be recovered.

Microlensing as a Possible Probe of Event-Horizon Structure in Quasars

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomozeiu, Mihai; Mohammed, Irshad; Rabold, Manuel

In quasars which are lensed by galaxies, the point-like images sometimes show sharp and uncorrelated brightness variations (microlensing). These brightness changes are associated with the innermost region of the quasar passing through a complicated pattern of caustics produced by the stars in the lensing galaxy. In this paper, we study whether the universal properties of optical caustics could enable extraction of shape information about the central engine of quasars. We present a toy model with a crescent-shaped source crossing a fold caustic. The silhouette of a black hole over an accretion disk tends to produce roughly crescent sources. When amore » crescent-shaped source crosses a fold caustic, the resulting light curve is noticeably different from the case of a circular luminosity profile or Gaussian source. With good enough monitoring data, the crescent parameters, apart from one degeneracy, can be recovered.« less

Microlensing as a Possible Probe of Event-Horizon Structure in Quasars

DOE PAGES

Tomozeiu, Mihai; Mohammed, Irshad; Rabold, Manuel; ...

2017-12-08

In quasars which are lensed by galaxies, the point-like images sometimes show sharp and uncorrelated brightness variations (microlensing). These brightness changes are associated with the innermost region of the quasar passing through a complicated pattern of caustics produced by the stars in the lensing galaxy. In this paper, we study whether the universal properties of optical caustics could enable extraction of shape information about the central engine of quasars. We present a toy model with a crescent-shaped source crossing a fold caustic. The silhouette of a black hole over an accretion disk tends to produce roughly crescent sources. When amore » crescent-shaped source crosses a fold caustic, the resulting light curve is noticeably different from the case of a circular luminosity profile or Gaussian source. With good enough monitoring data, the crescent parameters, apart from one degeneracy, can be recovered.« less

Heavy metal removal by caustic-treated yeast immobilized in alginate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lu, Y.; Wilkins, E.

1995-12-31

Saccharomyces cerevisiae yeast biomass was treated with hot alkali to increase its biosorption capacity for heavy metals and then was immobilized in alginate gel. Biosorption capacities for Cu{sup 2+}, Cd{sup 2+}, and Zn{sup 2+} on alginate gel, native yeast, native yeast immobilized in alginate gel, and caustic-treated yeast immobilized in alginate gel were all compared. Immobilized yeasts could be reactivated and reused in a manner similar to the ion exchange resins. Immobilized caustic-treated yeast has high heavy metal biosorption capacity and high metal removal efficiency in a rather wide acidic pH region. The biosorption isotherm of immobilized caustic-treated yeast wasmore » studied, and empirical equations were obtained. The initial pH of polluted water affected the metal removal efficiency significantly, and the equilibrium biosorption capacity seemed to be temperature independent at lower initial metal concentrations.« less

Prediction of sonic boom at a focus

NASA Technical Reports Server (NTRS)

Plotkin, K. J.; Cantril, J. M.

1976-01-01

The behavior of sonic boom at a focus has been reviewed for the purpose of extending present sonic boom computational methods to include focal zones. The geometry of a focal zone - whether a smooth caustic, a cusped caustic, or a perfect focus to a point - determines the character of focused signatures. The seeming contradiction of various experimental data can be resolved by noting these differences. A ray acoustic analysis has been developed for quantitative determination of caustic geometry. The only reliable theory presently available for signatures at a focus is for a smooth caustic. There has been some controversy between theoretical and experimental values of a constant in the scaling law for this case. It has been found that this discrepancy can be resolved by accounting for the finite thickness of real sonic boom shock waves. These findings have been incorporated into an existing sonic boom computer program.

Role of microstructure in caustic stress corrosion cracking of Alloy 690

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mertz, D.A.; Duda, P.T.; Pica, P.N.

1995-12-31

Alloy 690 has been selected for nuclear heat transport system tubing application in recent commercial reactor plants due to its resistance to multiple types of corrosion attack. Typical corn final heat treatments for this material are a mill-anneal (MA, approximately 1,070 C) to completely dissolve the carbides and develop the final grain structure plus a thermal treatment (TT, approximately 700 C) to precipitate carbides at the grain boundaries. Tubing with grain boundary carbides and no or few intragranular carbides has been found resistant to intergranular stress corrosion cracking (IGSCC) in caustic environments. In this work, first, Alloy 690 plate wasmore » subjected to a variety of MA and MA-TT heat treatments to create microstructures of carbide-decorated grain boundaries and undecorated boundaries. Caustic IGSCC test results were consistent with tubing data. Second, experiments were conducted to understand the mechanism by which caustic-corrosion resistance is imparted to Alloy 690 by grain boundary carbides. Tubing with a fully-developed MA-TT carbide microstructure was strained and heat-treated to create a mixed microstructure of new grain boundaries with no carbide precipitate decoration, intermixed with intragranular carbide strings from prior grain boundaries. Caustic SCC performance of this material was identical to that of material with the MA-TT carbide-decorated grain boundaries. This work suggests that the fundamental cause of good IGSCC resistance of MA-TT Alloy 690 in caustic does not derive solely from grain boundary carbides. It is suggested that matrix strength, as measured by yield stress, could be a controlling factor.« less

Laboratory scale Clean-In-Place (CIP) studies on the effectiveness of different caustic and acid wash steps on the removal of dairy biofilms.

PubMed

Bremer, Philip J; Fillery, Suzanne; McQuillan, A James

2006-02-15

A laboratory scale, bench top flow system was used to partially reproduce dairy plant conditions under which biofilms form and to quantify the effectiveness of caustic and acid wash steps in reducing the number of viable bacteria attached to stainless steel (SS) surfaces. Once bacteria attached to surfaces, a standard clean-in-place (CIP) regime (water rinse, 1% sodium hydroxide at 65 degrees C for 10 min, water rinse, 1.0% nitric acid at 65 degrees C for 10 min, water rinse) did not reproducibly ensure their removal. Standard CIP effectiveness was compared to alternative cleaning chemicals such as: caustic blends (Alkazolv 48, Ultrazolv 700, Concept C20, and Reflex B165); a caustic additive (Eliminator); acid blends (Nitroplus and Nitrobrite); and sanitizer (Perform). The addition of a caustic additive, Eliminator, enhanced biofilm removal compared to the standard CIP regime and further increases in cleaning efficiency occurred when nitric acid was substituted with Nitroplus. The combination of NaOH plus Eliminator and Nitroplus achieved a 3.8 log reduction in the number of cells recovered from the stainless steel surface. The incorporation of a sanitizer step into the CIP did not appear to enhance biofilm removal. This study has shown that the effectiveness of a "standard" CIP can possibly be enhanced through the testing and use of caustic and acid blends. There are many implications of these findings, including: the development of improved cleaning regimes and improved product quality, plant performance, and economic returns.

Intrinsic scatter of caustic masses and hydrostatic bias: An observational study

NASA Astrophysics Data System (ADS)

Andreon, S.; Trinchieri, G.; Moretti, A.; Wang, J.

2017-10-01

All estimates of cluster mass have some intrinsic scatter and perhaps some bias with true mass even in the absence of measurement errors for example caused by cluster triaxiality and large scale structure. Knowledge of the bias and scatter values is fundamental for both cluster cosmology and astrophysics. In this paper we show that the intrinsic scatter of a mass proxy can be constrained by measurements of the gas fraction because masses with higher values of intrinsic scatter with true mass produce more scattered gas fractions. Moreover, the relative bias of two mass estimates can be constrained by comparing the mean gas fraction at the same (nominal) cluster mass. Our observational study addresses the scatter between caustic (I.e., dynamically estimated) and true masses, and the relative bias of caustic and hydrostatic masses. For these purposes, we used the X-ray Unbiased Cluster Sample, a cluster sample selected independently from the intracluster medium content with reliable masses: 34 galaxy clusters in the nearby (0.050 < z < 0.135) Universe, mostly with 14 < log M500/M⊙ ≲ 14.5, and with caustic masses. We found a 35% scatter between caustic and true masses. Furthermore, we found that the relative bias between caustic and hydrostatic masses is small, 0.06 ± 0.05 dex, improving upon past measurements. The small scatter found confirms our previous measurements of a highly variable amount of feedback from cluster to cluster, which is the cause of the observed large variety of core-excised X-ray luminosities and gas masses.

Accessibility of Nitroxide Side Chains: Absolute Heisenberg Exchange Rates from Power Saturation EPR

PubMed Central

Altenbach, Christian; Froncisz, Wojciech; Hemker, Roy; Mchaourab, Hassane; Hubbell, Wayne L.

2005-01-01

In site-directed spin labeling, the relative solvent accessibility of spin-labeled side chains is taken to be proportional to the Heisenberg exchange rate (Wex) of the nitroxide with a paramagnetic reagent in solution. In turn, relative values of Wex are determined by continuous wave power saturation methods and expressed as a proportional and dimensionless parameter Π. In the experiments presented here, NiEDDA is characterized as a paramagnetic reagent for solvent accessibility studies, and it is shown that absolute values of Wex can be determined from Π, and that the proportionality constant relating them is independent of the paramagnetic reagent and mobility of the nitroxide. Based on absolute exchange rates, an accessibility factor is defined (0 < ρ < 1) that serves as a quantitative measure of side-chain solvent accessibility. The accessibility factors for a nitroxide side chain at 14 different sites in T4 lysozyme are shown to correlate with a structure-based accessibility parameter derived from the crystal structure of the protein. These results provide a useful means for relating crystallographic and site-directed spin labeling data, and hence comparing crystal and solution structures. PMID:15994891

DOE Office of Scientific and Technical Information (OSTI.GOV)

Josephson, Gary B.; Geeting, John GH; Bredt, Ofelia P.

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Waste Treatment Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes." The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEPmore » also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP; and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP; vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct injection of steam to accelerate the leach process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP-1, the 19-M NaOH is added to un-concentrated waste slurry (3-8 wt% solids), while for leaching in UFP-2, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before the addition of caustic. In both scenarios, following the caustic leach, the slurry was then concentrated to 17 wt% and washed with inhibited water to remove NaOH and other soluble salts. Next, the slurry was oxidatively leached using sodium permanganate to solubilize chrome. The slurry was then washed to remove the dissolved chrome and concentrated.« less

High-Dimensional Mutant and Modular Thermodynamic Cycles, Molecular Switching, and Free Energy Transduction

PubMed Central

Carter, Charles W.

2017-01-01

Understanding how distinct parts of proteins produce coordinated behavior has driven and continues to drive advances in protein science and enzymology. However, despite consensus about the conceptual basis for allostery, the idiosyncratic nature of allosteric mechanisms resists general approaches. Computational methods can identify conformational transition states from structural changes, revealing common switching mechanisms that impose multistate behavior. Thermodynamic cycles use factorial perturbations to measure coupling energies between side chains in molecular switches that mediate shear during domain motion. Such cycles have now been complemented by modular cycles that measure energetic coupling between separable domains. For one model system, energetic coupling between domains has been shown to be quantitatively equivalent to that between dynamic side chains. Linkages between domain motion, switching residues, and catalysis make nucleoside triphosphate hydrolysis conditional on domain movement, confirming an essential yet neglected aspect of free energy transduction and suggesting the potential generality of these studies. PMID:28375734

Stress corrosion cracking of duplex stainless steels in caustic solutions

NASA Astrophysics Data System (ADS)

Bhattacharya, Ananya

Duplex stainless steels (DSS) with roughly equal amount of austenite and ferrite phases are being used in industries such as petrochemical, nuclear, pulp and paper mills, de-salination plants, marine environments, and others. However, many DSS grades have been reported to undergo corrosion and stress corrosion cracking in some aggressive environments such as chlorides and sulfide-containing caustic solutions. Although stress corrosion cracking of duplex stainless steels in chloride solution has been investigated and well documented in the literature but the SCC mechanisms for DSS in caustic solutions were not known. Microstructural changes during fabrication processes affect the overall SCC susceptibility of these steels in caustic solutions. Other environmental factors, like pH of the solution, temperature, and resulting electrochemical potential also influence the SCC susceptibility of duplex stainless steels. In this study, the role of material and environmental parameters on corrosion and stress corrosion cracking of duplex stainless steels in caustic solutions were investigated. Changes in the DSS microstructure by different annealing and aging treatments were characterized in terms of changes in the ratio of austenite and ferrite phases, phase morphology and intermetallic precipitation using optical micrography, SEM, EDS, XRD, nano-indentation and microhardness methods. These samples were then tested for general and localized corrosion susceptibility and SCC to understand the underlying mechanisms of crack initiation and propagation in DSS in the above-mentioned environments. Results showed that the austenite phase in the DSS is more susceptible to crack initiation and propagation in caustic solutions, which is different from that in the low pH chloride environment where the ferrite phase is the more susceptible phase. This study also showed that microstructural changes in duplex stainless steels due to different heat treatments could affect their SCC susceptibility. Annealed and water quenched specimens were found to be immune to SCC in caustic environment. Aging treatment at 800°C gave rise to sigma and chi precipitates in the DSS. However, these sigma and chi precipitates, known to initiate cracking in DSS in chloride environment did not cause any cracking of DSS in caustic solutions. Aging of DSS at 475°C had resulted in '475°C embrittlement' and caused cracks to initiate in the ferrite phase. This was in contrast to the cracks initiating in the austenite phase in the as-received DSS. Alloy composition and microstructure of DSS as well as solution composition (dissolved ionic species) was also found to affect the electrochemical behavior and passivation of DSS which in turn plays a major role in stress corrosion crack initiation and propagation. Corrosion rates and SCC susceptibility of DSS was found to increase with addition of sulfide to caustic solutions. Corrosion films on DSS, characterized using XRD and X-ray photoelectron spectroscopy, indicated that the metal sulfide compounds were formed along with oxides at the metal surface in the presence of sulfide containing caustic environments. These metal sulfide containing passive films are unstable and hence breaks down under mechanical straining, leading to SCC initiations. The overall results from this study helped in understanding the mechanism of SCC in caustic solutions. Favorable slip systems in the austenite phase of DSS favors slip-induced local film damage thereby initiating a stress corrosion crack. Repeated film repassivation and breaking, followed by crack tip dissolution results in crack propagation in the austenite phase of DSS alloys. Result from this study will have a significant impact in terms of identifying the alloy compositions, fabrication processes, microstructures, and environmental conditions that may be avoided to mitigate corrosion and stress corrosion cracking of DSS in caustic solutions.

Light guide technology: using light to enhance safety

NASA Astrophysics Data System (ADS)

Lerner, William S.

2009-05-01

When used to detect extreme temperatures in harsh environments, warning devices have been placed at a distance from the "danger zone" for several reasons. The inability to mix electricity with flammable, caustic, liquid or volatile substances, the limited heat tolerances exhibited by most light sources, and the susceptibility of light sources to damage from vibration, have made the placement of a warning light directly within these harsh environments impossible. This paper describes a system that utilizes a beam of light to provide just such a warning. This system can be used with hard-wired or wireless sensors, side-light illumination, image projection and image transfer. The entire system may be self-contained and portable.

21 CFR 1230.35 - Hearings.

Code of Federal Regulations, 2013 CFR

2013-04-01

... POISON ACT Administrative Procedures § 1230.35 Hearings. Whenever it appears from the inspection, analysis, or test of any container that the provisions of section 3 or 6 of the Federal Caustic Poison Act... prosecution as a violation of the Federal Caustic Poison Act. ...

21 CFR 1230.35 - Hearings.

Code of Federal Regulations, 2012 CFR

2012-04-01

... POISON ACT Administrative Procedures § 1230.35 Hearings. Whenever it appears from the inspection, analysis, or test of any container that the provisions of section 3 or 6 of the Federal Caustic Poison Act... prosecution as a violation of the Federal Caustic Poison Act. ...

21 CFR 1230.35 - Hearings.

Code of Federal Regulations, 2010 CFR

2010-04-01

... POISON ACT Administrative Procedures § 1230.35 Hearings. Whenever it appears from the inspection, analysis, or test of any container that the provisions of section 3 or 6 of the Federal Caustic Poison Act... prosecution as a violation of the Federal Caustic Poison Act. ...

Caustic stress corrosion tests for the LLTR

DOE Office of Scientific and Technical Information (OSTI.GOV)

Indig, M.E.

1976-05-01

A series of tests have been performed in order to determine the effects of the caustic resulting from the Na/H/sub 2/O reaction on the materials used in the LLTR-MSG series of testing. Stainless steel, 2 /sup 1///sub 4/ Cr--1 Mo and carbon steel have been evaluated. Stress corrosion cracking susceptibility and general corrosion are reported. Over the range of temperature, caustic concentration and heating rate tested the stainless steel stressed to 90% of yield or above suffered cracking. Whereas, the 2-/sup 1///sub 4/ Cr--1 Mo and carbon steel were not cracked.

Continuous production of polymethylpentene membranes

DOEpatents

Epperson, B.J.; Burnett, L.J.; Helm, V.D.

1983-11-15

Gas separation membranes may be prepared in a continuous manner by passing a porous support which may, if so desired, be backed by a fabric through a solution of polymethylpentene dissolved in an organic solvent such as hexane. The support member is passed through the solution while one side thereof is in contact with a roller, thereby permitting only one side of the support member to be coated with the polymer. After continuously withdrawing the support member from the bath, the solvent is allowed to evaporate and the resulting membrane is recovered.

Method of removing and detoxifying a phosphorus-based substance

DOEpatents

Vandegrift, G.F.; Steindler, M.J.

1985-05-21

A method of removing a phosphorus-based poisonous substance from water contaminated is presented. In addition, the toxicity of the phosphorus-based substance is also subsequently destroyed. A water-immiscible organic solvent is first immobilized on a supported liquid membrane before the contaminated water is contacted with one side of the supported liquid membrane to absorb the phosphorus-based substance in the organic solvent. The other side of the supported liquid membrane is contacted with a hydroxy-affording strong base to react with phosphorus-based solvated species to form a non-toxic product.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harman-Ware, Anne E.; Sykes, Robert; Peter, Gary F.

Terpenoids, naturally occurring compounds derived from isoprene units present in pine oleoresin, are a valuable source of chemicals used in solvents, fragrances, flavors, and have shown potential use as a biofuel. This paper describes a method to extract and analyze the terpenoids present in loblolly pine saplings and pine lighter wood. Various extraction solvents were tested over different times and temperatures. Samples were analyzed by pyrolysis-molecular beam mass spectrometry before and after extractions to monitor the extraction efficiency. The pyrolysis studies indicated that the optimal extraction method used a 1:1 hexane/acetone solvent system at 22°C for 1 h. Extracts frommore » the hexane/acetone experiments were analyzed using a low thermal mass modular accelerated column heater for fast-GC/FID analysis. The most abundant terpenoids from the pine samples were quantified, using standard curves, and included the monoterpenes, α- and β-pinene, camphene, and δ-carene. Sesquiterpenes analyzed included caryophyllene, humulene, and α-bisabolene. In conclusion, diterpenoid resin acids were quantified in derivatized extractions, including pimaric, isopimaric, levopimaric, palustric, dehydroabietic, abietic, and neoabietic acids.« less

METAL RECOVERY/REMOVAL USING NON-ELECTROLYTIC METAL RECOVERY

EPA Science Inventory

Radiator repair shops most commonly use hot caustic solutions to clean radiator sections prior to resoldering. he hot caustic, or "boil-out" solutions as they are cabled in the trade, become contaminated with dirt, rust flakes, paint flakes and miscellaneous particulate debris. n...

21 CFR 1230.20 - General guaranty.

Code of Federal Regulations, 2011 CFR

2011-04-01

... CAUSTIC POISON ACT Guaranty § 1230.20 General guaranty. In lieu of a particular guaranty for each lot of... to _____ are not misbranded within the meaning of the Federal Caustic Poison Act. (Date) (Signature... Poison Act. (Date) (Signature and address of manufacturer or wholesaler) ...

21 CFR 1230.20 - General guaranty.

Code of Federal Regulations, 2010 CFR

2010-04-01

... CAUSTIC POISON ACT Guaranty § 1230.20 General guaranty. In lieu of a particular guaranty for each lot of... to _____ are not misbranded within the meaning of the Federal Caustic Poison Act. (Date) (Signature... Poison Act. (Date) (Signature and address of manufacturer or wholesaler) ...

21 CFR 1230.20 - General guaranty.

Code of Federal Regulations, 2012 CFR

2012-04-01

... CAUSTIC POISON ACT Guaranty § 1230.20 General guaranty. In lieu of a particular guaranty for each lot of... to _____ are not misbranded within the meaning of the Federal Caustic Poison Act. (Date) (Signature... Poison Act. (Date) (Signature and address of manufacturer or wholesaler) ...

21 CFR 1230.20 - General guaranty.

Code of Federal Regulations, 2013 CFR

2013-04-01

... CAUSTIC POISON ACT Guaranty § 1230.20 General guaranty. In lieu of a particular guaranty for each lot of... to _____ are not misbranded within the meaning of the Federal Caustic Poison Act. (Date) (Signature... Poison Act. (Date) (Signature and address of manufacturer or wholesaler) ...

21 CFR 1230.20 - General guaranty.

Code of Federal Regulations, 2014 CFR

2014-04-01

... CAUSTIC POISON ACT Guaranty § 1230.20 General guaranty. In lieu of a particular guaranty for each lot of... to _____ are not misbranded within the meaning of the Federal Caustic Poison Act. (Date) (Signature... Poison Act. (Date) (Signature and address of manufacturer or wholesaler) ...

Driven polymer translocation in good and bad solvent: Effects of hydrodynamics and tension propagation.

PubMed

Moisio, J E; Piili, J; Linna, R P

2016-08-01

We investigate the driven polymer translocation through a nanometer-scale pore in the presence and absence of hydrodynamics both in good and bad solvent. We present our results on tension propagating along the polymer segment on the cis side that is measured for the first time using our method that works also in the presence of hydrodynamics. For simulations we use stochastic rotation dynamics, also called multiparticle collision dynamics. We find that in the good solvent the tension propagates very similarly whether hydrodynamics is included or not. Only the tensed segment is by a constant factor shorter in the presence of hydrodynamics. The shorter tensed segment and the hydrodynamic interactions contribute to a smaller friction for the translocating polymer when hydrodynamics is included, which shows as smaller waiting times and a smaller exponent in the scaling of the translocation time with the polymer length. In the bad solvent hydrodynamics has a minimal effect on polymer translocation, in contrast to the good solvent, where it speeds up translocation. We find that under bad-solvent conditions tension does not spread appreciably along the polymer. Consequently, translocation time does not scale with the polymer length. By measuring the effective friction in a setup where a polymer in free solvent is pulled by a constant force at the end, we find that hydrodynamics does speed up collective polymer motion in the bad solvent even more effectively than in the good solvent. However, hydrodynamics has a negligible effect on the motion of individual monomers within the highly correlated globular conformation on the cis side and hence on the entire driven translocation under bad-solvent conditions.

Electrochemical sulfide removal and caustic recovery from spent caustic streams.

PubMed

Vaiopoulou, Eleni; Provijn, Thomas; Prévoteau, Antonin; Pikaar, Ilje; Rabaey, Korneel

2016-04-01

Spent caustic streams (SCS) are produced during alkaline scrubbing of sulfide containing sour gases. Conventional methods mainly involve considerable chemical dosing or energy expenditures entailing high cost but limited benefits. Here we propose an electrochemical treatment approach involving anodic sulfide oxidation preferentially to sulfur coupled to cathodic caustic recovery using a two-compartment electrochemical system. Batch experiments showed sulfide removal efficiencies of 84 ± 4% with concomitant 57 ± 4% efficient caustic production in the catholyte at a final concentration of 6.4 ± 0.1 wt% NaOH (1.6 M) at an applied current density of 100 A m(-2). Subsequent long-term continuous experiments showed that stable cell voltages (i.e. 2.7 ± 0.1 V) as well as constant sulfide removal efficiencies of 67 ± 5% at a loading rate of 47 g(S) L(-1) h(-1) were achieved over a period of 77 days. Caustic was produced at industrially relevant strengths for scrubbing (i.e. 5.1 ± 0.9 wt% NaOH) at current efficiencies of 96 ± 2%. Current density between 0 and 200 A m(-2) and sulfide loading rates of 50-200 g(S) L(-1) d(-1) were tested. The higher the current density the more oxidized the sulfur species produced and the higher the sulfide oxidation. On the contrary, high loading rate resulted in a reduction of sulfide oxidation efficiency. The results obtained in this study together with engineering calculations show that the proposed process could represent a cost-effective approach for sodium and sulfur recovery from SCS. Copyright © 2016 Elsevier Ltd. All rights reserved.

The public health impact of pediatric caustic ingestion injuries.

PubMed

Johnson, Christopher M; Brigger, Matthew T

2012-12-01

To determine the current public health burden of injuries due to caustic ingestion in children. The 2009 Kids' Inpatient Database provides data on a sample of all pediatric hospital discharges in the United States during that year. Children with caustic ingestion injuries requiring hospitalization were identified by corresponding codes from the International Classification of Diseases, Ninth Revision. Database analysis generated national estimates of summary statistics. A national database. Representative sample of all hospital discharge data on patients 18 years or younger. Public health burden related to caustic injury, including potential factors related to admission outcome, the necessity of a procedure during the admission, admission length of stay, and total charges for the admission. We estimated the prevalence of pediatric caustic ingestion injuries requiring hospitalization in the United States in 2009 to be 807 (95% CI, 731-882) children. The annual economic burden was estimated at $22 900 000 (95% CI, $15 400 000-$30 400 000) in total hospital charges. The mean charge per patient was estimated at $28 860 (95% CI, $19 799-$37 922) with a median of $9848. The mean length of admission was 4.13 (95% CI, 3.22-5.03) days with a median of 2 days. Among the 807 patients, 45.3% underwent esophagoscopy, and those admitted to teaching hospitals were more likely to undergo a procedure during their stay (P = .02). Logistic regression models suggested significant median income (P < .001) and sex (P < .001) variations. The current public health burden of pediatric caustic ingestion injuries may be less than commonly cited. This finding supports the notion that legislative efforts have been successful. Despite these successes, these injuries continue to impose a significant burden on health care resources.

Statistics of Microlensing Caustic Crossings in Q 2237+0305: Peculiar Velocity of the Lens Galaxy and Accretion Disk Size

NASA Astrophysics Data System (ADS)

Mediavilla, E.; Jimenez-Vicente, J.; Muñoz, J. A.; Mediavilla, T.; Ariza, O.

2015-01-01

We use the statistics of caustic crossings induced by microlensing in the lens system Q 2237+0305 to study the lens galaxy peculiar velocity. We calculate the caustic crossing rates for a comprehensive family of stellar mass functions and find a dependence of the average number of caustic crossings with the effective transverse velocity and the average mass, < n > \\propto {veff / \\sqrt{< m > }}, equivalent to the theoretical prediction for the case of microlenses with identical masses. We explore the possibilities of the method to measure v eff using the ~12 yr of Optical Gravitational Lensing Experiment monitoring of the four images of Q 2237+0305. To determine a lower limit for v eff, we count, conservatively, a single caustic crossing for each one of the four high magnification events identified in the literature (plus one additional proposed by us) obtaining veff ≳ 240\\sqrt{< m > /0.17 M_⊙ } km s-1 at 68% of confidence. From this value and the average FWHM of the four high magnification events, we obtain a lower limit of rs ≳ 1.4 \\sqrt{< m > /0.17 M_⊙ } light-days for the radius of the source (rs = FWHM/2.35). Tentative identification of three additional caustic crossing events leads to estimates of veff≃ (493+/- 246)\\sqrt{< m > /0.17 M_⊙ } km s-1 for the effective transverse velocity and of rs ≃ (2.7+/- 1.3)\\sqrt{< m > /0.17 M_⊙ } light-days for the source size. The estimated transverse peculiar velocity of the galaxy is vt ≃ (429+/- 246)\\sqrt{< m > /0.17 M_⊙ } km s-1.

PROCESSING ALTERNATIVES FOR DESTRUCTION OF TETRAPHENYLBORATE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lambert, D; Thomas Peters, T; Samuel Fink, S

Two processes were chosen in the 1980's at the Savannah River Site (SRS) to decontaminate the soluble High Level Waste (HLW). The In Tank Precipitation (ITP) process (1,2) was developed at SRS for the removal of radioactive cesium and actinides from the soluble HLW. Sodium tetraphenylborate was added to the waste to precipitate cesium and monosodium titanate (MST) was added to adsorb actinides, primarily uranium and plutonium. Two products of this process were a low activity waste stream and a concentrated organic stream containing cesium tetraphenylborate and actinides adsorbed on monosodium titanate (MST). A copper catalyzed acid hydrolysis process wasmore » built to process (3, 4) the Tank 48H cesium tetraphenylborate waste in the SRS's Defense Waste Processing Facility (DWPF). Operation of the DWPF would have resulted in the production of benzene for incineration in SRS's Consolidated Incineration Facility. This process was abandoned together with the ITP process in 1998 due to high benzene in ITP caused by decomposition of excess sodium tetraphenylborate. Processing in ITP resulted in the production of approximately 1.0 million liters of HLW. SRS has chosen a solvent extraction process combined with adsorption of the actinides to decontaminate the soluble HLW stream (5). However, the waste in Tank 48H is incompatible with existing waste processing facilities. As a result, a processing facility is needed to disposition the HLW in Tank 48H. This paper will describe the process for searching for processing options by SRS task teams for the disposition of the waste in Tank 48H. In addition, attempts to develop a caustic hydrolysis process for in tank destruction of tetraphenylborate will be presented. Lastly, the development of both a caustic and acidic copper catalyzed peroxide oxidation process will be discussed.« less

PEP Support Laboratory Leaching and Permeate Stability Tests

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russell, Renee L.; Peterson, Reid A.; Rinehart, Donald E.

2009-09-25

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes," of the External Flowsheet Review Team (EFRT) issue response plan.( ) The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes.more » The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. A simplified flow diagram of the PEP system is shown in Figure 1.1. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP and vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct injection of steam to accelerate the leach process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP-VSL-T01A and B, the 19-M NaOH is added to un-concentrated waste slurry (3 to 8 wt% solids), while for leaching in UFP-VSL-T02A, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before adding caustic.« less

Process for the disposal of alkali metals

DOEpatents

Lewis, Leroy C.

1977-01-01

Large quantities of alkali metals may be safely reacted for ultimate disposal by contact with a hot concentrated caustic solution. The alkali metals react with water in the caustic solution in a controlled reaction while steam dilutes the hydrogen formed by the reaction to a safe level.

High complication rate in reconstruction of Paprosky type IIIa acetabular defects using an oblong implant with modular side plates and a hook.

PubMed

Babis, G C; Sakellariou, V I; Chatziantoniou, A N; Soucacos, P N; Megas, P

2011-12-01

We report the results of 62 hips in 62 patients (17 males, 45 females) with mean age of 62.4 years (37 to 81), who underwent revision of the acetabular component of a total hip replacement due to aseptic loosening between May 2003 and November 2007. All hips had a Paprosky type IIIa acetabular defect. Acetabular revision was undertaken using a Procotyl E cementless oblong implant with modular side plates and a hook combined with impaction allografting. At a mean follow-up of 60.5 months (36 to 94) with no patients lost to follow-up and one died due to unrelated illness, the complication rate was 38.7%. Complications included aseptic loosening (19 hips), deep infection (3 hips), broken hook and side plate (one hip) and a femoral nerve palsy (one hip). Further revision of the acetabular component was required in 18 hips (29.0%) and a further four hips (6.4%) are currently loose and awaiting revision. We observed unacceptably high rates of complication and failure in our group of patients and cannot recommend this implant or technique.

Coordination Polymer Gels with Modular Nanomorphologies, Tunable Emissions, and Stimuli-Responsive Behavior Based on an Amphiphilic Tripodal Gelator.

PubMed

Sutar, Papri; Maji, Tapas Kumar

2017-08-21

The recent upsurge in research on coordination polymer gels (CPGs) stems from their synthetic modularity, nanoscale processability, and versatile functionalities. Here we report self-assembly of an amphiphilic, tripodal low-molecular weight gelator (L) that consists of 4,4',4-[1,3,5-phenyl-tri(methoxy)]-tris-benzene core and 2,2':6',2″-terpyridyl termini, with different metal ions toward the formation of CPGs that show controllable nanomorphologies, tunable emission, and stimuli-responsive behaviors. L can also act as a selective chemosensor for Zn II with very low limit of detection (0.18 ppm) in aqueous medium. Coordination-driven self-assembly of L with Zn II in H 2 O/MeOH solvent mixture results in a coordination polymer hydrogel (ZnL) that exhibits sheet like morphology and charge-transfer emission. On the other hand, coordination of L with Tb III and Eu III in CHCl 3 /tetrahydrofuran solvent mixture results in green- and red-emissive CPGs, respectively, with nanotubular morphology. Moreover, precise stoichiometric control of L/Eu III /Tb III ratio leads to the formation of bimetallic CPGs that show emissions over a broad spectral range, including white-light-emission. We also explore the multistimuli responsive properties of the white-light-emitting CPG by exploiting the dynamics of Ln III -tpy coordination.

Treatment of olefin plant spent caustic by combination of neutralization and Fenton reaction.

PubMed

Sheu, S H; Weng, H S

2001-06-01

Spent caustic from olefin plants contains much H2S and some mercaptans, phenols and oil. A new treatment process of spent caustic by neutralization followed by oxidation with Fenton's reagent (Fe2+/H2O2) was successfully developed. Over 90% of dissolved H2S were converted to gas phase by neutralization at pH = 5 and T = 70 degrees, and the vent gas stream could be introduced to sulfur recovery plant. The neutralized liquid was oxidized with OH. free radical, which was provided by a Fenton's reagent. The residual sulfides in the neutralized spent caustic were oxidized to less than 0.1 mg/L. The total COD removal of spent caustic is over 99.5% and the final COD value of the effluent can be lower than 100 mg/L under the following oxidation conditions: reaction time = 50 min, T = 90 degrees, Fe2+ = 100 mg/L, and a stoichiometric H2O2/COD = 1.1. The value is better than the 800 mg/L value obtained by common WAO process. The optimum pH of the Fenton reaction is around 2 for this process, and the oxidation step can maintain a pH value in the range of 1.8-2.4. Moreover, the iron catalyst can be recycled without affecting process effectiveness thus preventing secondary pollution.

40 CFR 63.8184 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2014 CFR

2014-07-01

... in the manufacture of product chlorine, product caustic, and by-product hydrogen at a plant site. This subpart covers mercury emissions from by-product hydrogen streams, end box ventilation system vents, and fugitive emission sources associated with cell rooms, hydrogen systems, caustic systems, and...

40 CFR 63.8184 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2011 CFR

2011-07-01

... in the manufacture of product chlorine, product caustic, and by-product hydrogen at a plant site. This subpart covers mercury emissions from by-product hydrogen streams, end box ventilation system vents, and fugitive emission sources associated with cell rooms, hydrogen systems, caustic systems, and...

40 CFR 63.8184 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2012 CFR

2012-07-01

... in the manufacture of product chlorine, product caustic, and by-product hydrogen at a plant site. This subpart covers mercury emissions from by-product hydrogen streams, end box ventilation system vents, and fugitive emission sources associated with cell rooms, hydrogen systems, caustic systems, and...

40 CFR 63.8184 - What parts of my plant does this subpart cover?

Code of Federal Regulations, 2013 CFR

2013-07-01

... in the manufacture of product chlorine, product caustic, and by-product hydrogen at a plant site. This subpart covers mercury emissions from by-product hydrogen streams, end box ventilation system vents, and fugitive emission sources associated with cell rooms, hydrogen systems, caustic systems, and...

EFRT M12 Issue Resolution: Comparison of PEP and Bench-Scale Oxidative Leaching Results

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rapko, Brian M.; Brown, Christopher F.; Eslinger, Paul W.

2009-08-14

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed and constructed and is to be operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes.” The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processesmore » using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP; and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP; vessels UFP-VSL-00001A and B in the WTP PTF). In both scenarios, 19-M sodium hydroxide solution (NaOH, caustic) is added to the waste slurry in the vessels to dissolve solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by a heating step that uses direct steam injection to accelerate the leaching process. Following the caustic leach, the vessel contents are cooled using vessel cooling jackets and/or external heat exchangers. The main difference between the two scenarios is that for leaching in UFP1, the 19-M NaOH is added to un-concentrated waste slurry (3 to 8 wt% solids), while for leaching in UFP2, the slurry is concentrated to nominally 20 wt% solids using cross-flow ultrafiltration before the addition of caustic. For wastes that have significantly high chromium content, the caustic leaching and slurry dewatering is followed by adding sodium permanganate to UFP-VSL-T02A, and the slurry is subjected to oxidative leaching at nominally ambient temperature. The purpose of the oxidative leaching is to selectively oxidize the poorly alkaline-soluble Cr(III) believed to be the insoluble form in Hanford tank sludge to the much more alkaline-soluble Cr(VI), e.g., chromate. The work described in this report provides the test results that are related to the efficiency of the oxidative leaching process to support process modeling based on tests performed with a Hanford waste simulant. The tests were completed both at the lab-bench scale and in the PEP. The purpose of this report is to summarize the results from both scales that are related to oxidative leaching chemistry to support a scale factor for the submodels to be used in the G2 model, which predicts WTP operating performance. Owing to schedule constraints, the PEP test data to be included in this report are limited to those from Integrated Tests A (T01 A/B caustic leaching) and B (T02A caustic leaching).« less

Sorting of Semiconducting Single-Walled Carbon Nanotubes in Polar Solvents with an Amphiphilic Conjugated Polymer Provides General Guidelines for Enrichment.

PubMed

Ouyang, Jianying; Ding, Jianfu; Lefebvre, Jacques; Li, Zhao; Guo, Chang; Kell, Arnold J; Malenfant, Patrick R L

2018-02-27

Conjugated polymer extraction (CPE) has been shown to be a highly effective method to isolate high-purity semiconducting single-walled carbon nanotubes (sc-SWCNTs). In both literature reports and industrial manufacturing, this method has enabled enrichment of sc-SWCNTs with high purity (≥99.9%). High selectivity is typically obtained in nonpolar aromatic solvents, yet polar solvents may provide process improvements in terms of yield, purity and efficiency. Using an amphiphilic fluorene-alt-pyridine conjugated copolymer with hydrophilic side chains, we have investigated the enrichment of sc-SWCNTs in polar solvents. Various conditions such as polymer/SWCNT ratio, solvent polarity, solvent dielectric constant as well as polymer solubility and SWCNT dispersibility were explored in order to optimize the purity and yield of the enriched product. Herein, we provide insights on CPE by demonstrating that a conjugated polymer having a hydrophobic backbone and hydrophilic oligo(ethylene oxide) side chains provides near full recovery (95%) of sc-SWCNTs using a multiextraction protocol. High purity is also obtained, and differences in chiral selectivity compared to analogous hydrophobic systems were confirmed by optical absorption and Raman spectroscopy as well as photoluminescence excitation mapping. Taking into consideration the solvent dielectric constant, polarity index as well as polymer solubility and SWCNT dispersibility provides a better understanding of structure-property effects on sc-SWCNT enrichment. The resulting hydrophilic SWCNT dispersions demonstrate long-term colloidal stability, making them suitable for ink formulation and high-performance thin-film transistors fabrication.

Time delay of critical images of a point source near the gravitational lens fold-caustic

NASA Astrophysics Data System (ADS)

Alexandrov, A.; Zhdanov, V.

2016-06-01

Within the framework of the analytical theory of the gravitational lensing we derive asymptotic formula for the time delay of critical images of apoint source, which is situated near a fold-caustic. We found corrections of the first and second order in powers of a parameter, which describescloseness of the source to the caustic. Our formula modifies earlier result by Congdon, Keeton &Nordgren (MNRAS, 2008) obtained in zero-orderapproximation. We have proved the hypothesis put forward by these authors that the first-order correction to the relative time delay of two criticalmages is identically zero. The contribution of the corrections is illustrated in model example by comparison with exact expression.

A Medical Monitoring Program for the Marine Hazardous Chemical Worker. Volume 1

DTIC Science & Technology

1985-12-01

ri-CR ESOL CRL 0 O-CRESOL CSL 0 P-CRESOL CSO 0 C RE SOL S CRS 0 CRESYLATE SPENT CAUSTIC CSC 0 CROTONALDEH’YDE CTA -0 C UPINE cuml 0 CYCLOHEXANE CHX 0...BLACk BASE 0 CARBON DISULIFIDE CBS 0 CARBON MONOG IDE CARBON TETRACHLORIDE CST 0 CAUSTIC POTASH SOLUTION CPS a CAUSTIC SODA SOLUTION CSS 0 CETYL ALCOHOL...HXN D 1 -𔃾.AENE HXE Ci HEXYLENE *;i -COL HX(G 0 H, TrClCHL0 . ACID 14CL 13 H’vDPC-wLO’.. ACID. SPENT (15%. OP LESS) Hcs C) HYSý90F! tOJCQ AC 10 HFA 0 H

Recovery of isopropyl alcohol from waste solvent of a semiconductor plant.

PubMed

Lin, Sheng H; Wang, Chuen S

2004-01-30

An important waste solvent generated in the semiconductor manufacturing process was characterized by high isopropyl alcohol (IPA) concentration over 65%, other organic pollutants and strong color. Because of these characteristics, IPA recovery was deemed as a logic choice for tackling this waste solvent. In the present work, an integrated method consisting of air stripping in conjunction with condensation and packed activated carbon fiber (ACF) adsorption for dealing with this waste solvent. The air stripping with proper stripping temperature control was employed to remove IPA from the waste solvent and the IPA vapor in the gas mixture was condensed out in a side condenser. The residual IPA remaining in the gas mixture exiting the side condenser was efficiently removed in a packed ACF column. The air stripping with condensation was able to recover up to 93% of total IPA in the initial waste solvent. The residual IPA in the gas mixture, representing less than 3% of the initial IPA, was efficiently captured in the packed ACF column. Experimental tests were conducted to examine the performances of each unit and to identify the optimum operating conditions. Theoretical modeling of the experimental IPA breakthrough curves was also undertaken using a macroscopic model. The verified breakthrough model significantly facilitates the adsorption column design. The recovered IPA was found to be of high purity and could be considered for reuse. Copyright 2003 Elsevier B.V.

A modular synthesis of dithiocarbamate pendant unnatural α-amino acids

EPA Science Inventory

Unnatural α-amino acids containing dithiocarbamate side chains were synthesized by a one-pot reaction of in-situ generated dithiocarbamate anions with sulfamidates. A wide range of these anions participated in the highly regio- and stereo-selective ring opening of sulfamidates to...

Individual Battery-Power Control for a Battery Energy Storage System Using a Modular Multilevel Cascade Converter

NASA Astrophysics Data System (ADS)

Yamagishi, Tsukasa; Maharjan, Laxman; Akagi, Hirofumi

This paper focuses on a battery energy storage system that can be installed in a 6.6-kV power distribution system. This system comprises a combination of a modular multilevel cascade converter based on single-star bridge-cells (MMCC-SSBC) and multiple battery modules. Each battery module is connected to the dc side of each bridge-cell, where the battery modules are galvanically isolated from each other. Three-phase multilevel line-to-line voltages with extremely low voltage steps on the ac side of the converter help in solving problems related to line harmonic currents and electromagnetic interference (EMI) issues. This paper proposes a control method that allows each bridge-cell to independently adjust the battery power flowing into or out of each battery module. A three-phase energy storage system using nine nickel-metal-hydride (NiMH) battery modules, each rated at 72V and 5.5Ah, is designed, constructed, and tested to verify the viability and effectiveness of the proposed control method.

[Understanding chair-side digital technology for stomatology from an engineering viewpoint].

PubMed

Zhao, Y J; Wang, Y

2018-04-09

In recent years with the rapid development of digital technology for stomatology, the application field, application model, technical features and technical connotation of the chair-side digital technology has got development and change. The open modular system has gradually replaced the traditional closed system, and the application field of digital technology is no longer limited to chair-side dental restoration, it also has been extend to various kinds of chair-side digital treatment-assisted technology. In this paper, from the engineering point of view, the up to date general connotation of chair-side digital technology was explained, the characteristics and the development of each unit in chair-side digital technology were analyzed, and the application pattern and the localization status were also discussed in this paper. The aim of this paper was to introduce the trend of chair-side digital technological to readers and to better guide clinical application.

Modular Toolkit for Data Processing (MDP): A Python Data Processing Framework.

PubMed

Zito, Tiziano; Wilbert, Niko; Wiskott, Laurenz; Berkes, Pietro

2008-01-01

Modular toolkit for Data Processing (MDP) is a data processing framework written in Python. From the user's perspective, MDP is a collection of supervised and unsupervised learning algorithms and other data processing units that can be combined into data processing sequences and more complex feed-forward network architectures. Computations are performed efficiently in terms of speed and memory requirements. From the scientific developer's perspective, MDP is a modular framework, which can easily be expanded. The implementation of new algorithms is easy and intuitive. The new implemented units are then automatically integrated with the rest of the library. MDP has been written in the context of theoretical research in neuroscience, but it has been designed to be helpful in any context where trainable data processing algorithms are used. Its simplicity on the user's side, the variety of readily available algorithms, and the reusability of the implemented units make it also a useful educational tool.

Comparison of robot surgery modular and total knee arthroplasty kinematics.

PubMed

Yildirim, Gokce; Fernandez-Madrid, Ivan; Schwarzkopf, Ran; Walker, Peter S; Karia, Raj

2014-04-01

The kinematics of seven knee specimens were measured from 0 to 120 degrees flexion using an up-and-down crouching machine. Motion was characterized by the positions of the centers of the lateral and medial femoral condyles in the anterior-posterior direction relative to a fixed tibia. A modular unicompartmental knee, trochlea flange, and patella resurfacing (multicompartmental knee [MCK] system) were implanted using a surgeon-interactive robot system that provided accurate surface matching. The MCK was tested, followed by standard cruciate retaining (CR) and posterior stabilized (PS) knees. The motion of the MCK was close to anatomic, especially on the medial side, in contrast to the CR and PS knees that showed abnormal motion features. Such a modular knee system, accurately inserted, has the potential for close to normal function in clinical application. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

40 CFR 63.1082 - What definitions do I need to know?

Code of Federal Regulations, 2011 CFR

2011-07-01

... includes direct-contact cooling water. Spent caustic waste stream means the continuously flowing process... compounds from process streams, typically cracked gas. The spent caustic waste stream does not include spent..., and the C4 butadiene storage equipment; and spent wash water from the C4 crude butadiene carbonyl wash...

40 CFR 63.1082 - What definitions do I need to know?

Code of Federal Regulations, 2012 CFR

2012-07-01

... includes direct-contact cooling water. Spent caustic waste stream means the continuously flowing process... compounds from process streams, typically cracked gas. The spent caustic waste stream does not include spent..., and the C4 butadiene storage equipment; and spent wash water from the C4 crude butadiene carbonyl wash...

40 CFR 63.1082 - What definitions do I need to know?

Code of Federal Regulations, 2014 CFR

2014-07-01

... includes direct-contact cooling water. Spent caustic waste stream means the continuously flowing process... compounds from process streams, typically cracked gas. The spent caustic waste stream does not include spent..., and the C4 butadiene storage equipment; and spent wash water from the C4 crude butadiene carbonyl wash...

40 CFR 63.1082 - What definitions do I need to know?

Code of Federal Regulations, 2013 CFR

2013-07-01

... includes direct-contact cooling water. Spent caustic waste stream means the continuously flowing process... compounds from process streams, typically cracked gas. The spent caustic waste stream does not include spent..., and the C4 butadiene storage equipment; and spent wash water from the C4 crude butadiene carbonyl wash...

Evaluation of Military Field-Water Quality. Volume 3. Opportunity Poisons

DTIC Science & Technology

1987-12-01

Acidic chemical cleaners fluoric acid, nitric acid, perchloric Spent acid acid, sulfuric acid Alkalies Miscellaneous caustic products Ammonia, lime...calcium oxide), potassium Alkaline battery fluid hydroxide, sodium hydroxide, sodium Caustic wastewater silicate Cleaning solutions Lye Nonhalogenated...Laboratory chemicals chloride, polychlorinated biphenyls, zinc Paint and varnish removers naphthenate , copper naphthenate , dichloro- Capacitors and

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... Specific Substances Affirmed as GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The...

Letter from Galo Jackson, USEPA to Prashant Gupta, Honeywell, Inc. Subject: Caustic Brine Offsite Shipments: LCP Chemical National Priorities List Site, Brunswick, Glynn County, GA

EPA Pesticide Factsheets

Feb. 17, 2012 letter about suspending all shipments of caustic brine from the LCP Chemicals site to the Water Recovery, Inc. facility in Jacksonville, FL. Region ID: 04 DocID: 10843423, DocDate: 02-17-2012

Flight test measurements and analysis of sonic boom phenomena near the shock wave extremity

NASA Technical Reports Server (NTRS)

Haglund, G. T.; Kane, E. J.

1973-01-01

The sonic boom flight test program conducted at Jackass Flats, Nevada, during the summer and fall of 1970 consisted of 121 sonic-boom-generating flights over the 1500 ft instrumented BREN tower. This test program was designed to provide information on several aspects of sonic boom, including caustics produced by longitudinal accelerations, caustics produced by steady flight near the threshold Mach number, sonic boom characteristics near lateral cutoff, and the vertical extent of shock waves attached to near-sonic airplanes. The measured test data, except for the near-sonic flight data, were analyzed in detail to determine sonic boom characteristics for these flight conditions and to determine the accuracy and the range of validity of linear sonic boom theory. The caustic phenomena observed during the threshold Mach number flights and during the transonic acceleration flights are documented and analyzed in detail. The theory of geometric acoustics is shown to be capable of predicting shock wave-ground intersections, and current methods for calculating sonic boom pressure signature away from caustics are shown to be reasonably accurate.

Multichannel microscale system for high throughput preparative separation with comprehensive collection and analysis

DOEpatents

Karger, Barry L.; Kotler, Lev; Foret, Frantisek; Minarik, Marek; Kleparnik, Karel

2003-12-09

A modular multiple lane or capillary electrophoresis (chromatography) system that permits automated parallel separation and comprehensive collection of all fractions from samples in all lanes or columns, with the option of further on-line automated sample fraction analysis, is disclosed. Preferably, fractions are collected in a multi-well fraction collection unit, or plate (40). The multi-well collection plate (40) is preferably made of a solvent permeable gel, most preferably a hydrophilic, polymeric gel such as agarose or cross-linked polyacrylamide.

Facilitating the Information Exchange Using a Modular Electronic Discharge Summary.

PubMed

Denecke, Kerstin; Dittli, Pascal A; Kanagarasa, Niveadha; Nüssli, Stephan

2018-01-01

Discharge summaries are a standard communication tool delivering important clinical information from inpatient to ambulatory care. To ensure a high quality, correctness and completeness, the generation process is time consuming. It requires also contributions of multiple persons. This is problematic since the primary care provider needs the information from the discharge summary for continuing the intended treatment. To address this challenge, we developed a concept for exchanging a modular electronic discharge summary. Through a literature review and interviews with multiple stakeholders, we analysed existing processes and derived requirements for an improved communication of the discharge summary. In this paper, we suggest a concept of a modular electronic discharge summary that is exchanged through the electronic patient dossier in CDA CH level 2 documents. Until 2020, all Swiss hospitals are obliged to connect to the electronic patient dossier. Our concept allows to access already completed modules of the discharge summary from the primary care side, before the entire report is entirely finalised. The data is automatically merged with the local patient record on the physician side and prepared for data integration into the practice information system. Our concept offers the opportunity not only to improve the information exchange between hospital and primary care, but it also provides a potential use case and demonstrates a benefit of the electronic patient dossier for primary care providers who are so far not obliged to connect to the patient dossier in Switzerland.

Feasibility Study of an Optical Caustic Plasmonic Light Scattering Sensor for Human Serum Anti-Dengue Protein E Antibody Detection

PubMed Central

García, Antonio A.; Pirez-Gomez, Miguel A.; Pech-Pacheco, José L.; Mendez-Galvan, Jorge F.; Machain-Williams, Carlos; Talavera-Aguilar, Lourdes; Espinosa-Carrillo, José H.; Duarte-Villaseñor, Miriam M.; Be-Ortiz, Christian; Espinosa-de los Monteros, Luz E.; Castillo-Pacheco, Ariel; Garcia-Rejon, Julian E.

2017-01-01

Antibody detection and accurate diagnosis of tropical diseases is essential to help prevent the spread of disease. However, most detection methods lack cost-effectiveness and field portability, which are essential features for achieving diagnosis in a timely manner. To address this, 3D-printed oblate spheroid sample chambers were fabricated to measure green light scattering of gold nanoparticles using an optical caustic focus to detect antibodies. Scattering signals of 20–200 nm gold nanoparticles using a green laser were compared to green light emitting diode (LED) light source signals and to Mie theory. The change in signal from 60 to 120 nm decreased in the order of Mie Theory > optical caustic scattering > 90° scattering. These results suggested that conjugating 60 nm gold nanoparticles and using an optical caustic system to detect plasmonic light scattering, would result in a sensitive test for detecting human antibodies in serum. Therefore, we studied the light scattering response of conjugated gold nanoparticles exposed to different concentrations of anti-protein E antibody, and a feasibility study of 10 human serum samples using dot blot and a handheld optical caustic-based sensor device. The overall agreement between detection methods suggests that the new sensor concept shows promise to detect gold nanoparticle aggregation in a homogeneous assay. Further testing and protocol optimization is needed to draw conclusions on the positive and negative predictive values for this new testing system. PMID:28817080

Covalent Surface Modification of Silicon Oxides with Alcohols in Polar Aprotic Solvents.

PubMed

Lee, Austin W H; Gates, Byron D

2017-09-05

Alcohol-based monolayers were successfully formed on the surfaces of silicon oxides through reactions performed in polar aprotic solvents. Monolayers prepared from alcohol-based reagents have been previously introduced as an alternative approach to covalently modify the surfaces of silicon oxides. These reagents are readily available, widely distributed, and are minimally susceptible to side reactions with ambient moisture. A limitation of using alcohol-based compounds is that previous reactions required relatively high temperatures in neat solutions, which can degrade some alcohol compounds or could lead to other unwanted side reactions during the formation of the monolayers. To overcome these challenges, we investigate the condensation reaction of alcohols on silicon oxides carried out in polar aprotic solvents. In particular, propylene carbonate has been identified as a polar aprotic solvent that is relatively nontoxic, readily accessible, and can facilitate the formation of alcohol-based monolayers. We have successfully demonstrated this approach for tuning the surface chemistry of silicon oxide surfaces with a variety of alcohol containing compounds. The strategy introduced in this research can be utilized to create silicon oxide surfaces with hydrophobic, oleophobic, or charged functionalities.

Risk factors associated with refractoriness to esophageal dilatation for benign dysphagia.

PubMed

Rodrigues-Pinto, Eduardo; Pereira, Pedro; Ribeiro, Armando; Lopes, Susana; Moutinho-Ribeiro, Pedro; Silva, Marco; Peixoto, Armando; Gaspar, Rui; Macedo, Guilherme

2016-06-01

Benign esophageal strictures need repeated dilatations to relieve dysphagia. Literature is scarce on the risk factors for refractoriness of these strictures. This study aimed to assess the risk factors associated with refractory strictures. This is a retrospective study of patients with benign esophageal strictures who were referred for esophageal dilatation over a period of 3 years. A total of 327 esophageal dilatations were performed in 103 patients; 53% of the patients reported dysphagia for liquids. Clinical success was achieved in 77% of the patients. There was a need for further dilatations in 54% of patients, being more frequent in patients with dysphagia for liquids [78 vs. 64%, P=0.008, odds ratio (OR) 1.930], in those with caustic strictures (89 vs. 70%, P=0.007, OR 3.487), and in those with complex strictures (83 vs. 70%, P=0.047, OR 2.132). Caustic strictures, peptic strictures, and complex strictures showed statistical significance in the multivariate analysis. Time until subsequent dilatations was less in patients with dysphagia for liquids (49 vs. 182 days, P<0.001), in those with peptic strictures (49 vs. 98 days, P=0.004), in those with caustic strictures (49 vs. 78 days, P=0.005), and in patients with complex strictures (47 vs. 80 days P=0.009). In multivariate analysis, further dilatations occurred earlier in patients with dysphagia for liquids [hazard ratio (HR) 1.506, P=0.004], in those with peptic strictures (HR 1.644, P=0.002), in those with caustic strictures (HR 1.581, P=0.016), and in patients with complex strictures (HR 1.408, P=0.046). Caustic, peptic, and complex strictures were associated with a greater need for subsequent dilatations. Time until subsequent dilatations was less in patients with dysphagia for liquids and in those with caustic, peptic, and complex strictures.

A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

USGS Publications Warehouse

Cravotta, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

2010-01-01

Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

STATISTICS OF MICROLENSING CAUSTIC CROSSINGS IN Q 2237+0305: PECULIAR VELOCITY OF THE LENS GALAXY AND ACCRETION DISK SIZE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mediavilla, E.; Jimenez-Vicente, J.; Muñoz, J. A.

We use the statistics of caustic crossings induced by microlensing in the lens system Q 2237+0305 to study the lens galaxy peculiar velocity. We calculate the caustic crossing rates for a comprehensive family of stellar mass functions and find a dependence of the average number of caustic crossings with the effective transverse velocity and the average mass, 〈n〉∝v{sub eff}/√(〈m〉), equivalent to the theoretical prediction for the case of microlenses with identical masses. We explore the possibilities of the method to measure v {sub eff} using the ∼12 yr of Optical Gravitational Lensing Experiment monitoring of the four images of Qmore » 2237+0305. To determine a lower limit for v {sub eff}, we count, conservatively, a single caustic crossing for each one of the four high magnification events identified in the literature (plus one additional proposed by us) obtaining v{sub eff}≳240√(〈m〉/0.17 M{sub ⊙}) km s{sup −1} at 68% of confidence. From this value and the average FWHM of the four high magnification events, we obtain a lower limit of r{sub s}≳1.4√(〈m〉/0.17 M{sub ⊙}) light-days for the radius of the source (r{sub s} = FWHM/2.35). Tentative identification of three additional caustic crossing events leads to estimates of v{sub eff}≃(493±246)√(〈m〉/0.17 M{sub ⊙}) km s{sup −1} for the effective transverse velocity and of r{sub s}≃(2.7±1.3)√(〈m〉/0.17 M{sub ⊙}) light-days for the source size. The estimated transverse peculiar velocity of the galaxy is v{sub t}≃(429±246)√(〈m〉/0.17 M{sub ⊙}) km s{sup −1}.« less

Backscattering of sound from targets in an Airy caustic formed by a curved reflecting surface

NASA Astrophysics Data System (ADS)

Dzikowicz, Benjamin Robert

The focusing of a caustic associated with the reflection of a locally curved sea floor or surface affects the scattering of sound by underwater targets. The most elementary caustic formed when sound reflects off a naturally curved surface is an Airy caustic. The case of a spherical target is examined here. With a point source acting also as a receiver, a point target lying in a shadow region returns only one echo directly from the target. When the target is on the Airy caustic, there are two echoes: one path is directly to the target and the other focuses off the curved surface. Echoes may be focused in both directions, the doubly focused case being the largest and the latest echo. With the target in the lit region, these different paths produce multiple echoes. For a finite sized sphere near an Airy caustic, all these echoes are manifest, but they occur at shifted target positions. Echoes of tone bursts reflecting only once overlap and interfere with each other, as do those reflecting twice. Catastrophe theory is used to analyze the echo amplitudes arising from these overlaps. The echo pressure for single reflections is shown to have a dependence on target position described by an Airy function for both a point and a finite target. With double focusing, this dependence is the square of an Airy function for a point target. With a finite sized target, (as in the experiment) this becomes a hyperbolic umbilic catastrophe integral with symmetric arguments. The arguments of each of these functions are derived from only the relative echo times of a transient pulse. Transient echo times are calculated using a numerical ray finding technique. Experiment confirms the predicted merging of transient echoes in the time domain, as well as the Airy and hyperbolic umbilic diffraction integral amplitudes for a tone burst. This method allows targets to be observed at greater distances in the presence of a focusing surface.

The Mechanism by Which Arabinoxylanases Can Recognize Highly Decorated Xylans*

PubMed Central

Labourel, Aurore; Crouch, Lucy I.; Brás, Joana L. A.; Jackson, Adam; Rogowski, Artur; Gray, Joseph; Yadav, Madhav P.; Henrissat, Bernard; Fontes, Carlos M. G. A.; Gilbert, Harry J.; Najmudin, Shabir; Baslé, Arnaud; Cuskin, Fiona

2016-01-01

The enzymatic degradation of plant cell walls is an important biological process of increasing environmental and industrial significance. Xylan, a major component of the plant cell wall, consists of a backbone of β-1,4-xylose (Xylp) units that are often decorated with arabinofuranose (Araf) side chains. A large penta-modular enzyme, CtXyl5A, was shown previously to specifically target arabinoxylans. The mechanism of substrate recognition displayed by the enzyme, however, remains unclear. Here we report the crystal structure of the arabinoxylanase and the enzyme in complex with ligands. The data showed that four of the protein modules adopt a rigid structure, which stabilizes the catalytic domain. The C-terminal non-catalytic carbohydrate binding module could not be observed in the crystal structure, suggesting positional flexibility. The structure of the enzyme in complex with Xylp-β-1,4-Xylp-β-1,4-Xylp-[α-1,3-Araf]-β-1,4-Xylp showed that the Araf decoration linked O3 to the xylose in the active site is located in the pocket (−2* subsite) that abuts onto the catalytic center. The −2* subsite can also bind to Xylp and Arap, explaining why the enzyme can utilize xylose and arabinose as specificity determinants. Alanine substitution of Glu68, Tyr92, or Asn139, which interact with arabinose and xylose side chains at the −2* subsite, abrogates catalytic activity. Distal to the active site, the xylan backbone makes limited apolar contacts with the enzyme, and the hydroxyls are solvent-exposed. This explains why CtXyl5A is capable of hydrolyzing xylans that are extensively decorated and that are recalcitrant to classic endo-xylanase attack. PMID:27531750

MULTIPOLE GRAVITATIONAL LENSING AND HIGH-ORDER PERTURBATIONS ON THE QUADRUPOLE LENS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chu, Z.; Lin, W. P.; Li, G. L.

2013-03-10

An arbitrary surface mass density of the gravitational lens can be decomposed into multipole components. We simulate the ray tracing for the multipolar mass distribution of the generalized Singular Isothermal Sphere model based on deflection angles, which are analytically calculated. The magnification patterns in the source plane are then derived from an inverse shooting technique. As has been found, the caustics of odd mode lenses are composed of two overlapping layers for some lens models. When a point source traverses this kind of overlapping caustics, the image numbers change by {+-}4, rather than {+-}2. There are two kinds of causticmore » images. One is the critical curve and the other is the transition locus. It is found that the image number of the fold is exactly the average value of image numbers on two sides of the fold, while the image number of the cusp is equal to the smaller one. We also focus on the magnification patterns of the quadrupole (m = 2) lenses under the perturbations of m = 3, 4, and 5 mode components and found that one, two, and three butterfly or swallowtail singularities can be produced, respectively. With the increasing intensity of the high-order perturbations, the singularities grow up to bring sixfold image regions. If these perturbations are large enough to let two or three of the butterflies or swallowtails make contact, then eightfold or tenfold image regions can be produced as well. The possible astronomical applications are discussed.« less

Searching for low percolation thresholds within amphiphilic polymer membranes: The effect of side chain branching

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dorenbos, G., E-mail: dorenbos@ny.thn.ne.jp

Percolation thresholds for solvent diffusion within hydrated model polymeric membranes are derived from dissipative particle dynamics in combination with Monte Carlo (MC) tracer diffusion calculations. The polymer backbones are composed of hydrophobic A beads to which at regular intervals Y-shaped side chains are attached. Each side chain is composed of eight A beads and contains two identical branches that are each terminated with a pendant hydrophilic C bead. Four types of side chains are considered for which the two branches (each represented as [C], [AC], [AAC], or [AAAC]) are splitting off from the 8th, 6th, 4th, or 2nd A bead,more » respectively. Water diffusion through the phase separated water containing pore networks is deduced from MC tracer diffusion calculations. The percolation threshold for the architectures containing the [C] and [AC] branches is at a water volume fraction of ∼0.07 and 0.08, respectively. These are much lower than those derived earlier for linear architectures of various side chain length and side chain distributions. Control of side chain architecture is thus a very interesting design parameter to decrease the percolation threshold for solvent and proton transports within flexible amphiphilic polymer membranes.« less

LITERATURE REVIEWS TO SUPPORT ION EXCHANGE TECHNOLOGY SELECTION FOR MODULAR SALT PROCESSING

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, W

2007-11-30

This report summarizes the results of literature reviews conducted to support the selection of a cesium removal technology for application in a small column ion exchange (SCIX) unit supported within a high level waste tank. SCIX is being considered as a technology for the treatment of radioactive salt solutions in order to accelerate closure of waste tanks at the Savannah River Site (SRS) as part of the Modular Salt Processing (MSP) technology development program. Two ion exchange materials, spherical Resorcinol-Formaldehyde (RF) and engineered Crystalline Silicotitanate (CST), are being considered for use within the SCIX unit. Both ion exchange materials havemore » been studied extensively and are known to have high affinities for cesium ions in caustic tank waste supernates. RF is an elutable organic resin and CST is a non-elutable inorganic material. Waste treatment processes developed for the two technologies will differ with regard to solutions processed, secondary waste streams generated, optimum column size, and waste throughput. Pertinent references, anticipated processing sequences for utilization in waste treatment, gaps in the available data, and technical comparisons will be provided for the two ion exchange materials to assist in technology selection for SCIX. The engineered, granular form of CST (UOP IE-911) was the baseline ion exchange material used for the initial development and design of the SRS SCIX process (McCabe, 2005). To date, in-tank SCIX has not been implemented for treatment of radioactive waste solutions at SRS. Since initial development and consideration of SCIX for SRS waste treatment an alternative technology has been developed as part of the River Protection Project Waste Treatment Plant (RPP-WTP) Research and Technology program (Thorson, 2006). Spherical RF resin is the baseline media for cesium removal in the RPP-WTP, which was designed for the treatment of radioactive waste supernates and is currently under construction in Hanford, WA. Application of RF for cesium removal in the Hanford WTP does not involve in-riser columns but does utilize the resin in large scale column configurations in a waste treatment facility. The basic conceptual design for SCIX involves the dissolution of saltcake in SRS Tanks 1-3 to give approximately 6 M sodium solutions and the treatment of these solutions for cesium removal using one or two columns supported within a high level waste tank. Prior to ion exchange treatment, the solutions will be filtered for removal of entrained solids. In addition to Tanks 1-3, solutions in two other tanks (37 and 41) will require treatment for cesium removal in the SCIX unit. The previous SCIX design (McCabe, 2005) utilized CST for cesium removal with downflow supernate processing and included a CST grinder following cesium loading. Grinding of CST was necessary to make the cesium-loaded material suitable for vitrification in the SRS Defense Waste Processing Facility (DWPF). Because RF resin is elutable (and reusable) and processing requires conversion between sodium and hydrogen forms using caustic and acidic solutions more liquid processing steps are involved. The WTP baseline process involves a series of caustic and acidic solutions (downflow processing) with water washes between pH transitions across neutral. In addition, due to resin swelling during conversion from hydrogen to sodium form an upflow caustic regeneration step is required. Presumably, one of these basic processes (or some variation) will be utilized for MSP for the appropriate ion exchange technology selected. CST processing involves two primary waste products: loaded CST and decontaminated salt solution (DSS). RF processing involves three primary waste products: spent RF resin, DSS, and acidic cesium eluate, although the resin is reusable and typically does not require replacement until completion of multiple treatment cycles. CST processing requires grinding of the ion exchange media, handling of solids with high cesium loading, and handling of liquid wash and conditioning solutions. RF processing requires handling and evaporation of cesium eluates, disposal of spent organic resin, and handling of the various liquid wash and regenerate solutions used. In both cases, the DSS will be immobilized in a low activity waste form. It appears that both technologies are mature, well studied, and generally suitable for this application. Technology selection will likely be based on downstream impacts or preferences between the various processing options for the two materials rather than on some unacceptable performance property identified for one material. As a result, the following detailed technical review and summary of the two technologies should be useful to assist in technology selection for SCIX.« less

The ecological impact of membrane-based extraction of phenolic compounds--a life cycle assessment study.

PubMed

Bayer, C; Follmann, M; Melin, T; Wintgens, T; Larsson, K; Almemark, M

2010-01-01

Many phenolic compounds show high boiling points, low molecular weights, moderate polarities or high toxicities. Therefore, conventional wastewater treatment is limited or expensive. Recycling of the separated compounds is often not possible. But, if liquid-liquid reactive extraction is linked to a non-porous membrane, some or all of the above mentioned limitations may be overcome. The key element is a composite membrane with a dense, hydrophobic top layer which avoids the mixing of the two aqueous fluid streams. The dilute phenol stream is one of them, the other is caustic soda as stripping solvent. Since the basics of this technology have been discussed before, the scope of this study is to facilitate process implementation and integration. To this end, a life cycle assessment framework is used to identify the optimal equipment size for the treatment of wastewater that may, for example, originate from the production of polycarbonate. Limiting for this application is not the environmental performance though, but most likely process economics.

Chemical cleaning of coal by molten caustic leaching after pretreatment by low-temperature devolatilization

DOEpatents

Chriswell, Colin D.; Kaushik, Surender M.; Shah, Navin D.; Markuszewski, Richard

1989-08-22

Pretreatment of coal by devolatization at temperatures ranging from about 420.degree. C. to about 450.degree. C. for from about 10 minutes to about 30 minutes before leaching with molten caustic leads to a significant reduction in carbonate formation, greatly reducing the cost of cleaning coal on a per ton basis.

3. Photocopy of photograph, U.S. Army, ca. 1943 (original print ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Photocopy of photograph, U.S. Army, ca. 1943 (original print located at Rocky Mountain Arsenal, Commerce City, Colorado). R.M.A. - 254 - CAUSTIC FUSION BLDG. LOOKING N.W. - Rocky Mountain Arsenal, Caustic Fusion Building, 450 feet South of December Seventh Avenue; 900 feet West of D Street, Commerce City, Adams County, CO

21 CFR 184.1763 - Sodium hydroxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium hydroxide. 184.1763 Section 184.1763 Food... GRAS § 184.1763 Sodium hydroxide. (a) Sodium hydroxide (NaOH, CAS Reg. No. 1310-73-2) is also known as sodium hydrate, soda lye, caustic soda, white caustic, and lye. The empirical formula is NaOH. Sodium...

Membrane assisted solvent extraction for rare earth element recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bhave, Ramesh R.; Kim, Daejin; Peterson, Eric S.

Systems and methods for the recovery of rare earth elements are provided. The systems and methods generally include membrane assisted solvent extraction using permeable hollow fibers having an immobilized organic phase within the pores of the hollow fibers. The permeable hollow fibers are generally in contact with an acidic aqueous feed on one side thereof and a strip solution on another side thereof. The systems and methods generally include the simultaneous extraction and stripping of rare earth elements as a continuous recovery process that is well suited for post-consumer products, end-of-life products, and other recovery sources of rare earth elements.

Simultaneous tuning of chemical composition and topography of copolymer surfaces: micelles as building blocks.

PubMed

Zhao, Ning; Zhang, Xiaoyan; Zhang, Xiaoli; Xu, Jian

2007-05-14

A simple method is described for controlling the surface chemical composition and topography of the diblock copolymer poly(styrene)-b-poly(dimethylsiloxane)(PS-b-PDMS) by casting the copolymer solutions from solvents with different selectivities. The surface morphology and chemical composition were characterized by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), respectively, and the wetting behavior was studied by water contact angle (CA) and sliding angle (SA) and by CA hysteresis. Chemical composition and morphology of the surface depend on solvent properties, humidity of the air, solution concentration, and block lengths. If the copolymer is cast from a common solvent, the resultant surface is hydrophobic, with a flat morphology, and dominated by PDMS on the air side. From a PDMS-selective solvent, the surface topography depends on the morphology of the micelles. Starlike micelles give rise to a featureless surface nearly completely covered by PDMS, while crew-cut-like micelles lead to a rough surface with a hierarchical structure that consists partly of PDMS. From a PS-selective solvent, however, surface segregation of PDMS was restricted, and the surface morphology can be controlled by vapor-induced phase separation. On the basis of the tunable surface roughness and PDMS concentration on the air side, water repellency of the copolymer surface could be tailored from hydrophobic to superhydrophobic. In addition, reversible switching behavior between hydrophobic and superhydrophobic can be achieved by exposing the surface to solvents with different selectivities.

On the Observability of Individual Population III Stars and Their Stellar-mass Black Hole Accretion Disks through Cluster Caustic Transits

NASA Astrophysics Data System (ADS)

Windhorst, Rogier A.; Timmes, F. X.; Wyithe, J. Stuart B.; Alpaslan, Mehmet; Andrews, Stephen K.; Coe, Daniel; Diego, Jose M.; Dijkstra, Mark; Driver, Simon P.; Kelly, Patrick L.; Kim, Duho

2018-02-01

We summarize panchromatic Extragalactic Background Light data to place upper limits on the integrated near-infrared surface brightness (SB) that may come from Population III stars and possible accretion disks around their stellar-mass black holes (BHs) in the epoch of First Light, broadly taken from z ≃ 7–17. Theoretical predictions and recent near-infrared power spectra provide tighter constraints on their sky signal. We outline the physical properties of zero-metallicity Population III stars from MESA stellar evolution models through helium depletion and of BH accretion disks at z≳ 7. We assume that second-generation non-zero-metallicity stars can form at higher multiplicity, so that BH accretion disks may be fed by Roche-lobe overflow from lower-mass companions. We use these near-infrared SB constraints to calculate the number of caustic transits behind lensing clusters that the James Webb Space Telescope and the next-generation ground-based telescopes may observe for both Population III stars and their BH accretion disks. Typical caustic magnifications can be μ ≃ {10}4{--}{10}5, with rise times of hours and decline times of ≲ 1 year for cluster transverse velocities of {v}T≲ 1000 km s‑1. Microlensing by intracluster-medium objects can modify transit magnifications but lengthen visibility times. Depending on BH masses, accretion-disk radii, and feeding efficiencies, stellar-mass BH accretion-disk caustic transits could outnumber those from Population III stars. To observe Population III caustic transits directly may require monitoring 3–30 lensing clusters to {AB}≲ 29 mag over a decade.

Preliminary study of efficacy of hyaluronic acid on caustic esophageal burns in an experimental rat model.

PubMed

Cevik, Muazez; Demir, Tuncer; Karadag, Cetin Ali; Ketani, Muzaffer Aydin; Celik, Hakim; Kaplan, Davut Sinan; Boleken, Mehmet Emin

2013-04-01

The aim of this study was to investigate the effectiveness of hyaluronic acid on the prevention of esophageal damage and stricture formation after experimental caustic (alkaline) esophageal injury in rats. Twenty-one Wistar albino rats were randomly divided into three groups. A caustic esophageal burn was created following the Gehanno model: Group l (n=7) underwent operation, but no injury; Group 2 (n=7) was injured and left untreated; and Group 3 (n=7) was injured and treated with hyaluronic acid, first topically and then orally by gavage (2×0.3mL; 12.5mg/mL for 7days). The caustic esophageal burn was created by instilling 25% NaOH into the distal esophagus. All rats were euthanized on day 22 for evaluation. The efficacy of hyaluronic acid treatment was assessed histopathologically and biochemically via blood determination of the total antioxidant status (TAS), total oxidant status (TOS), oxidative stress index (OSI), and sulfhydryl group (SH) and lipid hydroperoxidase (LOOH) levels. Statistical analyses were performed. Weight gain was significantly lower in Group 2 than in the other two groups (P<0.05). The mean stenosis index, histopathologic damage score, TAS, TOS, OSI, and SH and LOOH levels were higher in Group 2 than in the other two groups. The mean stenosis index, inflammation, TAS, SH and OSI in Group 2 were significantly different than those in the other two groups (P<0.05). Hyaluronic acid treatment is effective in treating damage and preventing strictures after caustic esophageal burn in rats. Copyright © 2013 Elsevier Inc. All rights reserved.

Revealing stellar brightness profiles by means of microlensing fold caustics

NASA Astrophysics Data System (ADS)

Dominik, M.

2004-09-01

With a handful of measurements of limb-darkening coefficients, galactic microlensing has already proven to be a powerful technique for studying atmospheres of distant stars. Survey campaigns such as OGLE-III are capable of providing ~10 suitable target stars per year that undergo microlensing events involving passages over the caustic created by a binary lens, which last from a few hours to a few days and allow us to resolve the stellar atmosphere by frequent broad-band photometry. For a caustic exit lasting 12 h and a photometric precision of 1.5 per cent, a moderate sampling interval of 30 min (corresponding to ~25-30 data points) is sufficient for providing a reliable measurement of the linear limb-darkening coefficient Γ with an uncertainty of ~8 per cent, which reduces to ~3 per cent for a reduced sampling interval of 6 min for the surroundings of the end of the caustic exit. While some additional points over the remaining parts of the light curve are highly valuable, a denser sampling in these regions provides little improvement. Unless an accuracy of less than 5 per cent is desired, limb-darkening coefficients for several filters can be obtained or observing time can be spent on other targets during the same night. The adoption of an inappropriate stellar brightness profile as well as the effect of acceleration between source and caustic yield distinguishable characteristic systematics in the model residuals. Acceleration effects are unlikely to affect the light curve significantly for most events, although a free acceleration parameter blurs the limb-darkening measurement if the passage duration cannot be accurately determined.

Alkaline flooding for enhanced oil recovery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gittler, W.E.

1983-09-01

There are over 12 active projects of varying size using one of 3 major types of alkaline agents. These include sodium silicate, caustic soda, and soda ash. Among the largest pilots currently is the THUMS project in the Wilmington field, California. Plans called for the injection of a 4% weight concentration of sodium orthosilicate over a 60% PV. Through the first 3 yr, over 27 million bbl of chemicals have been injected. Gulf Oil is operating several alkaline floods, one of which is located off shore in the Quarantine Bay field, Louisiana. In this pilot, sodium hydroxide in a weightmore » concentration of 5 to 12% is being injected. Belco Petroleum Corp. has reported that their pilot operating in the Isenhour Unit in Wyoming is using a .5% weight concentration of soda ash in conjunction with a polymer. Other uses for alkaline agents in chemical flooding include the use of silicate as a preflush or sacrificial agent in micellar/polymer and surfactant recovery systems. In addition, caustic has been tested in the surface-mixed caustic emulsion process while orthosilicate has been tested in a recovery method known as mobility-controlled caustic floods.« less

Simulations of sonic boom ray tube area fluctuations for propagation through atmospheric turbulence including caustics via a Monte Carlo method

NASA Technical Reports Server (NTRS)

Sparrow, Victor W.; Pierce, Allan D.

1992-01-01

A theory which gives statistical predictions for how often sonic booms propagating through the earth's turbulent boundary layer will encounter caustics, given the spectral properties of the atmospheric turbulence, is outlined. The theory is simple but approximately accounts for the variation of ray tube areas along ray paths. This theory predicts that the variation of ray tube areas is determined by the product of two similar area factors, psi (x) and phi (x), each satisfying a generic harmonic oscillator equation. If an area factor increases the peak acoustic pressure decreases, and if the factor decreases the peak acoustic pressure increases. Additionally, if an area factor decreases to zero and becomes negative, the ray has propagated through a caustic, which contributes a phase change of 90 degrees to the wave. Thus, it is clear that the number of times that a sonic boom wave passes through a caustic should be related to the distorted boom waveform received on the ground. Examples are given based on a characterization of atmospheric turbulence due to the structure function of Tatarski as modified by Crow.

Caustics and Rogue Waves in an Optical Sea.

PubMed

Mathis, Amaury; Froehly, Luc; Toenger, Shanti; Dias, Frédéric; Genty, Goëry; Dudley, John M

2015-08-06

There are many examples in physics of systems showing rogue wave behaviour, the generation of high amplitude events at low probability. Although initially studied in oceanography, rogue waves have now been seen in many other domains, with particular recent interest in optics. Although most studies in optics have focussed on how nonlinearity can drive rogue wave emergence, purely linear effects have also been shown to induce extreme wave amplitudes. In this paper, we report a detailed experimental study of linear rogue waves in an optical system, using a spatial light modulator to impose random phase structure on a coherent optical field. After free space propagation, different random intensity patterns are generated, including partially-developed speckle, a broadband caustic network, and an intermediate pattern with characteristics of both speckle and caustic structures. Intensity peaks satisfying statistical criteria for rogue waves are seen especially in the case of the caustic network, and are associated with broader spatial spectra. In addition, the electric field statistics of the intermediate pattern shows properties of an "optical sea" with near-Gaussian statistics in elevation amplitude, and trough-to-crest statistics that are near-Rayleigh distributed but with an extended tail where a number of rogue wave events are observed.

Caustics and Rogue Waves in an Optical Sea

PubMed Central

Mathis, Amaury; Froehly, Luc; Toenger, Shanti; Dias, Frédéric; Genty, Goëry; Dudley, John M.

2015-01-01

There are many examples in physics of systems showing rogue wave behaviour, the generation of high amplitude events at low probability. Although initially studied in oceanography, rogue waves have now been seen in many other domains, with particular recent interest in optics. Although most studies in optics have focussed on how nonlinearity can drive rogue wave emergence, purely linear effects have also been shown to induce extreme wave amplitudes. In this paper, we report a detailed experimental study of linear rogue waves in an optical system, using a spatial light modulator to impose random phase structure on a coherent optical field. After free space propagation, different random intensity patterns are generated, including partially-developed speckle, a broadband caustic network, and an intermediate pattern with characteristics of both speckle and caustic structures. Intensity peaks satisfying statistical criteria for rogue waves are seen especially in the case of the caustic network, and are associated with broader spatial spectra. In addition, the electric field statistics of the intermediate pattern shows properties of an “optical sea” with near-Gaussian statistics in elevation amplitude, and trough-to-crest statistics that are near-Rayleigh distributed but with an extended tail where a number of rogue wave events are observed. PMID:26245864

Caustics and the growth of droplets

NASA Astrophysics Data System (ADS)

Govindarajan, Rama; Ravichandran, S.; Ray, Samriddhi; Deepu, P.

Caustics are formed when inertial particles of very different velocities collide in a flow, and are a consequence of the dissipative nature of particle motion in a suspension. Using a model vortex-dominated flow with heavy droplets in a saturated environment, we suggest that sling caustics form only within a neighbourhood around a vortex, the square of whose radius is proportional to the product of circulation and particle inertia. Droplets starting close to this critical radius congregate very close together, resulting in large spikes in (Lagrangian) number density. Allowing for merger when droplets collide, we show that droplets starting out close to the critical radius display a much more rapid growth in size than those starting elsewhere, and a large fraction of the large droplets are those that originate within the caustics-forming region. We test these predictions in a two-dimensional simulation of turbulent flow. We hope that our study will be of interest in long-standing problems of physical interest such as the mechanism of broadening of droplet spectra in a turbulent flow. Support from the Ministry of Earth Sciences, Government of India for the project Coupled physical processes in the Bay of Bengal and monsoon air-sea interaction under OMM is gratefully acknowledged.

Backscattering from targets residing in caustics resulting from ocean boundary interactions

NASA Astrophysics Data System (ADS)

Dzikowicz, Benjamin R.; Marston, Philip L.

2005-04-01

Detection of targets by backscatter in shallow water can be enhanced by interactions with ocean boundaries. A laboratory experiment is performed where a spherical target passes through an Airy caustic formed by a curved surface. When the target resides in the insonified region of the caustic there are two sets of multi-path rays: two pairs reflecting once off the surface (either to or from the target), and three reflecting twice off the surface (to and from the target). When a target moves across the caustic the singly reflected rays merge, as do the doubly reflected. With a longer tone burst the rays in each set overlap and the backscatter is greatly enhanced as the target moves into the insonified region. For a point target the singly reflected backscatter scales as an Airy function [B. R. Dzikowicz and P. L. Marston, J. Acoust. Soc. Am. 116, 2751-2757 (2004)], and the doubly reflected as the square of an Airy function. For a finite target the doubly reflected backscatter unfolds into a hyperbolic umbilic function. The arguments of the Airy and Hyperbolic Umbilic functions are calculated using the relative echo times of transient pulses. [Work supported by ONR.

[Acquired caustic vagina stenosis: Surgical outcomes of 21 cases].

PubMed

Séni, K; Horo, A G; Koffi, A; Aka, K E; Fomba, M; Koné, M

2016-03-01

To document epidemiology, causes, anatomical varieties and surgical management outcomes of caustic acquired vagina stenosis. Retrospective study of 21 patients involved from 1996 to 2012 at the department of obstetrics and gynecology of Yopougon's teaching hospital in Abidjan, Côte d'Ivoire. Vaginal stenosis due to genital malformation, vaginal irradiation of pelvic tumours, repair of bladder and vaginal fistulae or intersexual disorders were excluded. The prevalence was 0.14/1000 admissions, mean age was 32.1 years, mean gravidity was 1.76 and mean parity was 1.1. Vaginal stenosis seat and extent were variable and 100 % had a caustic origin by use of traditional medicine vaginal pessaire. Of the patients, 95.2 % underwent surgical treatment followed by several dilations sessions with glass dilators. Successful surgical outcome allowing coitus was achieved in 47.6 % of cases with 52.4 % failure. Acquired caustic vagina stenosis are frequently occurring and are a public health problem related to ignorance. Health education and establishment of expert centers with exchange of experiences in West Africa should be able to improve surgical outcomes. Copyright © 2016. Published by Elsevier SAS.

Modular microfluidic systems using reversibly attached PDMS fluid control modules

NASA Astrophysics Data System (ADS)

Skafte-Pedersen, Peder; Sip, Christopher G.; Folch, Albert; Dufva, Martin

2013-05-01

The use of soft lithography-based poly(dimethylsiloxane) (PDMS) valve systems is the dominating approach for high-density microscale fluidic control. Integrated systems enable complex flow control and large-scale integration, but lack modularity. In contrast, modular systems are attractive alternatives to integration because they can be tailored for different applications piecewise and without redesigning every element of the system. We present a method for reversibly coupling hard materials to soft lithography defined systems through self-aligning O-ring features thereby enabling easy interfacing of complex-valve-based systems with simpler detachable units. Using this scheme, we demonstrate the seamless interfacing of a PDMS-based fluid control module with hard polymer chips. In our system, 32 self-aligning O-ring features protruding from the PDMS fluid control module form chip-to-control module interconnections which are sealed by tightening four screws. The interconnection method is robust and supports complex fluidic operations in the reversibly attached passive chip. In addition, we developed a double-sided molding method for fabricating PDMS devices with integrated through-holes. The versatile system facilitates a wide range of applications due to the modular approach, where application specific passive chips can be readily attached to the flow control module.

Direct Causticizing for Black Liquor Gasification in a Circulating Fluidized Bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott Sinquefield; Xiaoyan Zeng, Alan Ball

2010-03-02

Gasification of black liquor (BLG) has distinct advantages over direct combustion in Tomlinson recovery boilers. In this project we seek to resolve causticizing issues in order to make pressurized BLG even more efficient and cost-effective. One advantage of BLG is that the inherent partial separation of sulfur and sodium during gasification lends itself to the use of proven high yield variants to conventional kraft pulping which require just such a separation. Processes such as polysulfide, split sulfidity, ASAQ, and MSSAQ can increase pulp yield from 1% to 10% over conventional kraft but require varying degrees of sulfur/sodium separation, which requiresmore » additional [and costly] processing in a conventional Tomlinson recovery process. However during gasification, the sulfur is partitioned between the gas and smelt phases, while the sodium all leaves in the smelt; thus creating the opportunity to produce sulfur-rich and sulfur-lean white liquors for specialty pulping processes. A second major incentive of BLG is the production of a combustible product gas, rich in H2 and CO. This product gas (a.k.a. “syngas”) can be used in gas turbines for combined cycle power generation (which is twice as efficient as the steam cycle alone), or it can be used as a precursor to form liquid fuels, such as dimethyl ether or Fischer Tropsh diesel. There is drawback to BLG, which has the potential to become a third major incentive if this work is successful. The causticizing load is greater for gasification of black liquor than for combustion in a Tomlinson boiler. So implementing BLG in an existing mill would require costly increases to the causticizing capacity. In situ causticizing [within the gasifier] would handle the entire causticizing load and therefore eliminate the lime cycle entirely. Previous work by the author and others has shown that titanate direct causticizing (i.e. in situ) works quite well for high-temperature BLG (950°C), but was limited to pressures below about 5 bar. It is desirable however to operate BLG at 20-30 bar for efficiency reasons related to either firing the syngas in a turbine, or catalytically forming liquid fuels. This work focused on achieving high direct causticizing yields at 20 bars pressure. The titanate direct causticizing reactions are inhibited by CO2. Previous work has shown that the partial pressure of CO2 should be kept below about 0.5 bar in order for the process to work. This translates to a total reactor pressure limit of about 5 bar for airblown BLG, and only 2 bar for O2-blown BLG. In this work a process was developed in which the CO2 partial pressure could be manipulated to a level under 0.5 bar with the total system pressure at 10 bar during O2-blown BLG. This fell short of our 20 bar goal but still represents a substantial increase in the pressure limit. A material and energy balance was performed, as well as first-pass economics based on capital and utilities costs. Compared to a reference case of using BLG with a conventional lime cycle [Larson, 2003], the IRR and NVP were estimated for further replacing the lime kiln with direct causticizing. The economics are strongly dependent on the price of lime kiln fuel. At $6/mmBTU the lime cycle is the clear choice. At $8/mmBTU the NPV is $10M with IRR of 17%. At $12/mmBTU the NPV is $45M with IRR of 36%. To further increase the total allowable pressure, the CO2 could be further decreased by further decreasing the temperature. Testing should be done at 750C. Also a small pilot should be built.« less

Removing Al and regenerating caustic soda from the spent washing liquor of Al etching

NASA Astrophysics Data System (ADS)

Barakat, M. A.; El-Sheikh, S. M.; Farghly, F. E.

2005-08-01

Spent liquor from washing of aluminum section materials after etching with caustic soda (NaOH) has been treated. Aluminum was removed from the liquor and caustic soda was regenerated by adding precipitating agents to hydrolyze sodium aluminate (Na2AlO2), separating the aluminumprecipitate, and concentrating free NaOH in the resulting solution for reuse in the etching process. Four systems were investigated: hydrated lime [Ca(OH)2], hydrogen peroxide (H2O2), H2O2/Ca(OH)2 mixture, and dry lime (CaO). Results revealed that CaO was more efficient in the removal of aluminum from the spent liquor with a higher hydrolyzing rate of Na2AlO2 than Ca(OH)2, H2O2, or their mixture.

Estimation of terpene content in loblolly pine biomass using a hybrid fast-GC and pyrolysis-molecular beam mass spectrometry method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harman-Ware, Anne E.; Davis, Mark F.; Peter, Gary F.

Terpenes can be used as renewable fuels and chemicals and quantifying their presence in biomass is becoming increasingly important. A novel method was developed to rapidly quantify total diterpenoid resin acids using pyrolysis-molecular beam mass spectrometry (py-MBMS). Pine sapling monoterpenes and diterpenoids were extracted from wood using a 1:1 (v/v) mixture of hexane and acetone and analyses were performed before and after extraction to determine the extraction efficiency of the solvent system. The resulting extract was analyzed for total diterpenoid content using py-MBMS and was combined with total monoterpene content that was determined using a low thermal mass modular acceleratedmore » column heater (LTM MACH) fast-GC/FID to measure the terpene content present in pine saplings. Oleoresin extruded from larger pine trees was used to validate mass balance closure of the terpene content in the extract solvent.« less

Estimation of terpene content in loblolly pine biomass using a hybrid fast-GC and pyrolysis-molecular beam mass spectrometry method

DOE PAGES

Harman-Ware, Anne E.; Davis, Mark F.; Peter, Gary F.; ...

2017-01-16

Terpenes can be used as renewable fuels and chemicals and quantifying their presence in biomass is becoming increasingly important. A novel method was developed to rapidly quantify total diterpenoid resin acids using pyrolysis-molecular beam mass spectrometry (py-MBMS). Pine sapling monoterpenes and diterpenoids were extracted from wood using a 1:1 (v/v) mixture of hexane and acetone and analyses were performed before and after extraction to determine the extraction efficiency of the solvent system. The resulting extract was analyzed for total diterpenoid content using py-MBMS and was combined with total monoterpene content that was determined using a low thermal mass modular acceleratedmore » column heater (LTM MACH) fast-GC/FID to measure the terpene content present in pine saplings. Oleoresin extruded from larger pine trees was used to validate mass balance closure of the terpene content in the extract solvent.« less

Long Duration Exposure Facility

DTIC Science & Technology

1988-06-30

Blue and Oxazine Dyes- Name Absorption -mazimu= Lasing Wavelengths un. un. (solvent) (solvent) Nile Blue A, 635 690 Perchlorate (ethanol) (ethanol...Fluence(/cm Etching 5 Al 3.5 MeV 5x10 6 N NaOH 6 o BI8 PrQtons Ixl0 50 C, 15 hr. 6 C9 (normal 3x10 (2 sided) incidence) 01 (unirradiated) 5 DIS 2.0

Analysis of the Nucleophilic Solvation Effects in Isopropyl Chlorothioformate Solvolysis

PubMed Central

D’Souza, Malcolm J.; Mahon, Brian P.; Kevill, Dennis N.

2010-01-01

Correlation of the solvent effects through application of the extended Grunwald-Winstein equation to the solvolysis of isopropyl chlorothioformate results in a sensitivity value of 0.38 towards changes in solvent nucleophilicity (l) and a sensitivity value of 0.72 towards changes in solvent ionizing power (m). This tangible l value coupled with the negative entropies of activation observed indicates a favorable predisposition towards a modest rear-side nucleophilic solvation of a developing carbocation. Only in 100% ethanol was the bimolecular pathway dominant. These observations are very different from those obtained for the solvolysis of isopropyl chloroformate, where dual reaction channels were proposed, with the addition-elimination reaction favored in the more nucleophilic solvents and a unimolecular fragmentation-ionization mechanism favored in the highly ionizing solvents. PMID:20717524

When an Elected Official Fails to Play Nice: The Legal Implications and Lessons Learned from Associations with a Caustic School Board Member

ERIC Educational Resources Information Center

Weiler, Spencer C.

2015-01-01

In November of 2009 Mr. Sean Lyndon was elected to the Verde Mountain School Board and by February 2012 he resigned from this position. During his tumultuous tenure, Mr. Lyndon's antics proved divisive, caustic, and disruptive to the governance process. These actions included belittling and intimidating fellow school board members and school…

Modular supramolecular approach for co-crystallization of donors and acceptors into ordered networks

DOEpatents

Stupp, Samuel I.; Stoddart, J. Fraser; Shveyd, Alex K.; Tayi, Alok S.; Sue, Andrew C. H.; Narayanan, Ashwin

2016-09-20

Organic charge-transfer (CT) co-crystals in a mixed stack system are disclosed, wherein a donor molecule (D) and an acceptor molecule (A) occupy alternating positions (DADADA) along the CT axis. A platform is provided which amplifies the molecular recognition of donors and acceptors and produces co-crystals at ambient conditions, wherein the platform comprises (i) a molecular design of the first constituent (.alpha.-complement), (ii) a molecular design of the second compound (.beta.-complement), and (iii) a solvent system that promotes co-crystallization.

Modular supramolecular approach for co-crystallization of donors and acceptors into ordered networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stupp, Samuel I.; Stoddart, J. Fraser; Shveyd, Alexander K.

Organic charge-transfer (CT) co-crystals in a mixed stack system are disclosed, wherein a donor molecule (D) and an acceptor molecule (A) occupy alternating positions (DADADA) along the CT axis. A platform is provided which amplifies the molecular recognition of donors and acceptors and produces co-crystals at ambient conditions, wherein the platform comprises (i) a molecular design of the first constituent (.alpha.-complement), (ii) a molecular design of the second compound (.beta.-complement), and (iii) a solvent system that promotes co-crystallization.

Aqueous Processing for Printed Organic Electronics: Conjugated Polymers with Multistage Cleavable Side Chains

PubMed Central

2017-01-01

The ability to process conjugated polymers via aqueous solution is highly advantageous for reducing the costs and environmental hazards of large scale roll-to-roll processing of organic electronics. However, maintaining competitive electronic properties while achieving aqueous solubility is difficult for several reasons: (1) Materials with polar functional groups that provide aqueous solubility can be difficult to purify and characterize, (2) many traditional coupling and polymerization reactions cannot be performed in aqueous solution, and (3) ionic groups, though useful for obtaining aqueous solubility, can lead to a loss of solid-state order, as well as a screening of any applied bias. As an alternative, we report a multistage cleavable side chain method that combines desirable aqueous processing attributes without sacrificing semiconducting capabilities. Through the attachment of cleavable side chains, conjugated polymers have for the first time been synthesized, characterized, and purified in organic solvents, converted to a water-soluble form for aqueous processing, and brought through a final treatment to cleave the polymer side chains and leave behind the desired electronic material as a solvent-resistant film. Specifically, we demonstrate an organic soluble polythiophene that is converted to an aqueous soluble polyelectrolyte via hydrolysis. After blade coating from an aqueous solution, UV irradiation is used to cleave the polymer’s side chains, resulting in a solvent-resistant, electroactive polymer thin film. In application, this process results in aqueous printed materials with utility for solid-state charge transport in organic field effect transistors (OFETs), along with red to colorless electrochromism in ionic media for color changing displays, demonstrating its potential as a universal method for aqueous printing in organic electronics. PMID:28979937

Aqueous Processing for Printed Organic Electronics: Conjugated Polymers with Multistage Cleavable Side Chains.

PubMed

Schmatz, Brian; Yuan, Zhibo; Lang, Augustus W; Hernandez, Jeff L; Reichmanis, Elsa; Reynolds, John R

2017-09-27

The ability to process conjugated polymers via aqueous solution is highly advantageous for reducing the costs and environmental hazards of large scale roll-to-roll processing of organic electronics. However, maintaining competitive electronic properties while achieving aqueous solubility is difficult for several reasons: (1) Materials with polar functional groups that provide aqueous solubility can be difficult to purify and characterize, (2) many traditional coupling and polymerization reactions cannot be performed in aqueous solution, and (3) ionic groups, though useful for obtaining aqueous solubility, can lead to a loss of solid-state order, as well as a screening of any applied bias. As an alternative, we report a multistage cleavable side chain method that combines desirable aqueous processing attributes without sacrificing semiconducting capabilities. Through the attachment of cleavable side chains, conjugated polymers have for the first time been synthesized, characterized, and purified in organic solvents, converted to a water-soluble form for aqueous processing, and brought through a final treatment to cleave the polymer side chains and leave behind the desired electronic material as a solvent-resistant film. Specifically, we demonstrate an organic soluble polythiophene that is converted to an aqueous soluble polyelectrolyte via hydrolysis. After blade coating from an aqueous solution, UV irradiation is used to cleave the polymer's side chains, resulting in a solvent-resistant, electroactive polymer thin film. In application, this process results in aqueous printed materials with utility for solid-state charge transport in organic field effect transistors (OFETs), along with red to colorless electrochromism in ionic media for color changing displays, demonstrating its potential as a universal method for aqueous printing in organic electronics.

The conceptual design of a robust, compact, modular tokamak reactor based on high-field superconductors

NASA Astrophysics Data System (ADS)

Whyte, D. G.; Bonoli, P.; Barnard, H.; Haakonsen, C.; Hartwig, Z.; Kasten, C.; Palmer, T.; Sung, C.; Sutherland, D.; Bromberg, L.; Mangiarotti, F.; Goh, J.; Sorbom, B.; Sierchio, J.; Ball, J.; Greenwald, M.; Olynyk, G.; Minervini, J.

2012-10-01

Two of the greatest challenges to tokamak reactors are 1) large single-unit cost of each reactor's construction and 2) their susceptibility to disruptions from operation at or above operational limits. We present an attractive tokamak reactor design that substantially lessens these issues by exploiting recent advancements in superconductor (SC) tapes allowing peak field on SC coil > 20 Tesla. A R˜3.3 m, B˜9.2 T, ˜ 500 MW fusion power tokamak provides high fusion gain while avoiding all disruptive operating boundaries (no-wall beta, kink, and density limits). Robust steady-state core scenarios are obtained by exploiting the synergy of high field, compact size and ideal efficiency current drive using high-field side launch of Lower Hybrid waves. The design features a completely modular replacement of internal solid components enabled by the demountability of the coils/tapes and the use of an immersion liquid blanket. This modularity opens up the possibility of using the device as a nuclear component test facility.

Biodegradable Stents for Caustic Esophageal Strictures: Do They Work?

PubMed

Kochhar, Rakesh; Samanta, Jayanta; Basha, Jahangeer; Verma, Abhai; Choudhuri, Gourdas; Lakhtakia, Sundeep; Reddy, D Nageshwar

2017-08-01

Biodegradable (BD) stents have been used for the management of various esophageal strictures (ES) but the experience of its use in caustic strictures is limited. The present study, aimed at evaluating efficacy of BD stents for the treatment of refractory caustic-induced ES, was a retrospective multi-center study conducted at three tertiary care centers in India wherein adult patients with refractory caustic induced strictures underwent placement of a BD stent. Patients were followed up for immediate complications and long term outcome. All 13 patients (39.3 ± 15.1 years) underwent successful BD stent placement. Retrosternal chest pain occurred in 2 patients and stent migration in 1 (7.6%) patient. At 3 months, restenosis with recurrence of dysphagia was seen in nine (69.2%) patients, at 6 months, 10 (77%) patients had dysphagia of whom three underwent surgery and the remaining seven patients required dilatations. At 1 year, one patient remained asymptomatic while nine had dysphagia. The requirement for dilatation was once in 3 months in seven patients & once in a month in two patients. At 2 years, the requirement of dilatations was further reduced to once in 4-6 months in all patients. Over a 3 year follow up three (23%) patients had undergone surgery, one was free of symptoms while nine patients continued to be on periodic dilatation although the requirement had reduced to once in 4-6 months. Efficacy of BD stents in patients with caustic-induced ES is limited and the short term radial force applied by the currently available BD stents is inadequate to provide long term relief in such patients.

Early endoscopic balloon dilation in caustic-induced gastric injury.

PubMed

Kochhar, Rakesh; Poornachandra, Kuchhangi Sureshchandra; Dutta, Usha; Agrawal, Amit; Singh, Kartar

2010-04-01

There are no reports on endoscopic balloon dilation (EBD) for caustic-induced gastric outlet obstruction (GOO) in the acute or subacute phase. To study the efficacy of early EBD in patients with caustic-induced gastric injury. Tertiary care center in India. Retrospective analysis of data. Out of 41 patients with caustic-induced GOO who reported to us in the subacute phase between January 2001 and December 2008, 31 were treated by EBD. All 31 had ingested an acid 14.39 +/- 4.65 days earlier. EBD was achieved by using wire-guided balloons under endoscopic guidance. The balloon was negotiated across the narrowed segment and inflated for 60 seconds using a pressure gun. Balloons of incremental diameter, up to a maximum of 3 sizes, were used in each sitting. Procedural success was defined as reaching the end point of dilation (15 mm) and absence of symptoms. All 31 patients (18 male, mean age 32.06 +/- 11.04 years) could be successfully dilated. All but 1 underwent successful dilations to achieve the end point of 15 mm, requiring a median of 9 (range 3-18) dilations over a period of 7 (range 1.5-16) weeks. Complications included self-limiting pain (n = 10), bleeding at the time of the procedure (n = 9), and perforation in 1 patient (3.2%) who required surgery. Thirty patients were followed up for a median of 21 (range 3-72) months with no recurrence. Early EBD by an expert endoscopist is a safe and effective treatment modality in the management of caustic-induced GOO. Copyright 2010 American Society for Gastrointestinal Endoscopy. Published by Mosby, Inc. All rights reserved.

Two-Pole Caustic Model for High-Energy Lightcurves of Pulsars

NASA Technical Reports Server (NTRS)

Dyks, J.; Rudak, B.

2003-01-01

We present a new model of high-energy lightcurves from rotation powered pulsars. The key ingredient of the model is the gap region (i.e. the region where particle acceleration is taking place and high-energy photons originate) which satisfies the following assumptions: i) the gap region extends from each polar cap to the light cylinder; ii) the gap is thin and confined to the surface of last open magnetic-field lines; iii) photon emissivity is uniform within the gap region. The model lightcurves are dominated by strong peaks (either double or single) of caustic origin. Unlike in other pulsar models with caustic effects, the double peaks arise due to crossing two caustics, each of which is associated with a different magnetic pole. The generic features of the lightcurves are consistent with the observed characteristics of pulsar lightcurves: 1) the most natural (in terms of probability) shape consists of two peaks (separated by 0.4 to 0.5 in phase for large viewing angles); 2) the peaks possess well developed wings; 3) there is a bridge (inter-peak) emission component; 4) there is a non-vanishing off-pulse emission level; 5) the radio pulse occurs before the leading high-energy peak. The model is well suited for four gamma-ray pulsars - Crab, Vela, Geminga and B1951+32 - with double-peak lightcurves exhibiting the peak separation of 0.4 to 0.5 in phase. Hereby, we apply the model to the Vela pulsar. Moreover, we indicate the limitation of the model in accurate reproducing of the lightcurves with single pulses and narrowly separated (about 0.2 in phase) pulse peaks. We also discuss the optical polarization properties for the Crab pulsar in the context of the two-pole caustic model.

Tension Amplification in Molecular Brushes in Solutions and on Substrates

PubMed Central

Panyukov, Sergey; Zhulina, Ekaterina B.; Sheiko, Sergei S.; Randall, Greg C.; Brock, James; Rubinstein, Michael

2009-01-01

Molecular bottle-brushes are highly branched macromolecules with side chains densely grafted to a long polymer backbone. The brush-like architecture allows focusing of the side-chain tension to the backbone and its amplification from the picoNewton to nanoNewton range. The backbone tension depends on the overall molecular conformation and the surrounding environment. Here we study the relation between the tension and conformation of the molecular brushes in solutions, melts, and on substrates. In solutions, we find that the backbone tension in dense brushes with side chains attached to every backbone monomer is on the order of f0N3/8 in athermal solvents, f0N1/3 in θ-solvents, and f0 in poor solvents and melts, where N is the degree of polymerization of side chains, f0≃ kBT/b is the maximum tension in side chains, b is the Kuhn length, kB is Boltzmann constant, and T is absolute temperature. Depending on the side chain length and solvent quality, molecular brushes in solutions develop tension on the order of 10–100 picoNewtons, which is sufficient to break hydrogen bonds. Significant amplification of tension occurs upon adsorption of brushes onto a substrate. On a strongly attractive substrate, maximum tension in the brush backbone is ~ f0N, reaching values on the order of several nanoNewtons which exceed the strength of a typical covalent bond. At low grafting density and high spreading parameter the cross-sectional profile of adsorbed molecular brush is approximately rectangular with thicknes ~bA/S, where A is the Hamaker constant and S is the spreading parameter. At a very high spreading parameter (S > A), the brush thickness saturates at monolayer ~ b. At a low spreading parameter, the cross-sectional profile of adsorbed molecular brush has triangular tent-like shape. In the cross-over between these two opposite cases, covering a wide range of parameter space, the adsorbed molecular brush consists of two layers. Side chains in the lower layer gain surface energy due to the direct interaction with the substrate, while the second layer spreads on the top of the first layer. Scaling theory predicts that this second layer has a triangular cross-section with width R ~ N3/5 and height h ~ N2/5. Using self-consistent field theory we calculate the cap profile y (x) = h (1 − x2/R2)2, where x is the transverse distance from the backbone. The predicted cap shape is in excellent agreement with both computer simulation and experiment. PMID:19673133

Evolution of velocity dispersion along cold collisionless flows

DOE PAGES

Banik, Nilanjan; Sikivie, Pierre

2016-05-01

We found that the infall of cold dark matter onto a galaxy produces cold collisionless flows and caustics in its halo. If a signal is found in the cavity detector of dark matter axions, the flows will be readily apparent as peaks in the energy spectrum of photons from axion conversion, allowing the densities, velocity vectors and velocity dispersions of the flows to be determined. We also discuss the evolution of velocity dispersion along cold collisionless flows in one and two dimensions. A technique is presented for obtaining the leading behaviour of the velocity dispersion near caustics. The results aremore » used to derive an upper limit on the energy dispersion of the Big Flow from the sharpness of its nearby caustic, and a prediction for the dispersions in its velocity components.« less

Production of intergranular attack of alloy 600, alloy 690, and alloy 800 tubing in tubesheet crevices: Topical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, D.B.; Glaves, C.L.,

1987-07-01

Three model boilers, manufactured to simulate full-size tube sheet crevices, were tested with various secondary side environments. The first was faulted with organics representative of the decomposition of humic acid. The second was faulted with sodium carbonate and sodium hydroxide, while the third was faulted with sodium sulfate and sodium hydroxide. Each model contained seven tubes, which included Alloy 600 in the mill-annealed (MA) and thermally-treated (TT) conditions and Alloy 690 in the thermally-treated condition. Two models contained Alloy 800 tubes in the mill-annealed condition and one had Alloy 800 in the mill-annealed/cold-worked/glass-bead-peened condition. Two different sizes of tubesheet crevicesmore » were used in all model boilers. In the organics-faulted boiler, tubes of Alloy 600MA, Alloy 690TT and Alloy 800MA experienced no significant intergranular attack (IGA); however, the Alloy 600TT had intergranular attack (IGA) three to four grains deep. The carbonate-caustic faulted boiler experienced throughwall stress corrosion cracking (SCC) in all tubes of Alloy 600 MA and Alloy 800 MA. Eddy current indications were present in Alloy 690TT, Alloy 600TT and Alloy 800 in the mill-annealed/cold worked/glass-bead-peened condition. Metallographic examination of tubes from the third model boiler, faulted with sodium sulfate and caustic, revealed IGA in the mill-annealed Alloy 600 tubes. The IGA was more extensive in an Alloy 600 tube annealed at 1700/sup 0/F than an Alloy 600 tube annealed at 1875/sup 0/F.« less

Method for preparing membranes with adjustable separation performance

DOEpatents

Peterson, E.S.; Orme, C.J.; Stone, M.L.

1995-01-31

Methods for adjustable separation of solutes and solvents involve the combination of the use of a maximally swollen membrane and subsequent vacuum depressurization exerted on the permeate side of that membrane. By adjusting the extent of depressurization it is possible to separate solvent from solutes and solutes from each other. Improved control of separation parameters as well as improved flux rates characterize the present invention. 2 figs.

Method for preparing membranes with adjustable separation performance

DOEpatents

Peterson, Eric S.; Orme, Christopher J.; Stone, Mark L.

1995-01-01

Methods for adjustable separation of solutes and solvents involve the combination of the use of a maximally swollen membrane and subsequent vacuum depressurization exerted on the permeate side of that membrane. By adjusting the extent of depressurization it is possible to separate solvent from solutes and solutes from each other. Improved control of separation parameters as well as improved flux rates characterize the present invention.

The economic pre-treatment of coal mine drainage water with caustic and ozone.

PubMed

Boyden, B H; Nador, L; Addleman, S; Jeston, L

2017-09-01

Coal mine drainage waters are low in pH with varying amounts of iron and manganese and are generally brackish. The Austar Coal Mine in NSW, Australia, sought alternatives to their current lime dosing as the pre-treatment before the downstream reverse osmosis plant. Undesirable operating aspects of the current system include manganese and gypsum scaling/fouling, the need for anti-scalants and reduced water recovery. Thirteen processes for acid mine drainage were initially considered. The preferred process of caustic and ozone for Mn(II) oxidation was pilot tested at up to 0.74 kL/hr at the mine site. Under proper conditions and no aeration, about 81 per cent of the Fe could be removed (initially at 156 mg/L) as green rust. Supplemental aeration followed first-order kinetics and allowed 99.9 per cent Fe(II) oxidation and removal but only with a hydraulic residence time of about 47 minutes. The addition of supplemental Cu catalyst improved Fe removal. Ozone applied after caustic was effective in stoichiometrically oxidising recalcitrant Mn(II) and any remaining Fe(II). Control of the ozonation was achieved using the oxidation reduction potential during oxidation of the Mn(II) species. The use of caustic, followed by ozone, proved economically comparable to the current lime pre-treatment.

Reflective and refractive objects for mixed reality.

PubMed

Knecht, Martin; Traxler, Christoph; Winklhofer, Christoph; Wimmer, Michael

2013-04-01

In this paper, we present a novel rendering method which integrates reflective or refractive objects into a differential instant radiosity (DIR) framework usable for mixed-reality (MR) applications. This kind of objects are very special from the light interaction point of view, as they reflect and refract incident rays. Therefore they may cause high-frequency lighting effects known as caustics. Using instant-radiosity (IR) methods to approximate these high-frequency lighting effects would require a large amount of virtual point lights (VPLs) and is therefore not desirable due to real-time constraints. Instead, our approach combines differential instant radiosity with three other methods. One method handles more accurate reflections compared to simple cubemaps by using impostors. Another method is able to calculate two refractions in real-time, and the third method uses small quads to create caustic effects. Our proposed method replaces parts in light paths that belong to reflective or refractive objects using these three methods and thus tightly integrates into DIR. In contrast to previous methods which introduce reflective or refractive objects into MR scenarios, our method produces caustics that also emit additional indirect light. The method runs at real-time frame rates, and the results show that reflective and refractive objects with caustics improve the overall impression for MR scenarios.

Wavefronts, actions and caustics determined by the probability density of an Airy beam

NASA Astrophysics Data System (ADS)

Espíndola-Ramos, Ernesto; Silva-Ortigoza, Gilberto; Sosa-Sánchez, Citlalli Teresa; Julián-Macías, Israel; de Jesús Cabrera-Rosas, Omar; Ortega-Vidals, Paula; Alejandro Juárez-Reyes, Salvador; González-Juárez, Adriana; Silva-Ortigoza, Ramón

2018-07-01

The main contribution of the present work is to use the probability density of an Airy beam to identify its maxima with the family of caustics associated with the wavefronts determined by the level curves of a one-parameter family of solutions to the Hamilton–Jacobi equation with a given potential. To this end, we give a classical mechanics characterization of a solution of the one-dimensional Schrödinger equation in free space determined by a complete integral of the Hamilton–Jacobi and Laplace equations in free space. That is, with this type of solution, we associate a two-parameter family of wavefronts in the spacetime, which are the level curves of a one-parameter family of solutions to the Hamilton–Jacobi equation with a determined potential, and a one-parameter family of caustics. The general results are applied to an Airy beam to show that the maxima of its probability density provide a discrete set of: caustics, wavefronts and potentials. The results presented here are a natural generalization of those obtained by Berry and Balazs in 1979 for an Airy beam. Finally, we remark that, in a natural manner, each maxima of the probability density of an Airy beam determines a Hamiltonian system.

Comparison of ultrasound-assisted and traditional caustic leaching of spent cathode carbon (SCC) from aluminum electrolysis.

PubMed

Xiao, Jin; Yuan, Jie; Tian, Zhongliang; Yang, Kai; Yao, Zhen; Yu, Bailie; Zhang, Liuyun

2018-01-01

The spent cathode carbon (SCC) from aluminum electrolysis was subjected to caustic leaching to investigate the different effects of ultrasound-assisted and traditional methods on element fluorine (F) leaching rate and leaching residue carbon content. Sodium hydroxide (NaOH) dissolved in deionized water was used as the reaction system. Through single-factor experiments and a comparison of two leaching techniques, the optimum F leaching rate and residue carbon content for ultrasound-assisted leaching process were obtained at a temperature of 70°C, residue time of 40min, initial mass ratio of alkali to SCC (initial alkali-to-material ratio) of 0.6, liquid-to-solid ratio of 10mL/g, and ultrasonic power of 400W, respectively. Under the optimal conditions, the leaching residue carbon content was 94.72%, 2.19% larger than the carbon content of traditional leaching residue. Leaching wastewater was treated with calcium chloride (CaCl 2 ) and bleaching powder and the treated wastewater was recycled caustic solution. All in all, benefiting from advantage of the ultrasonication effects, ultrasound-assisted caustic leaching on spent cathode carbon had 55.6% shorter residue time than the traditional process with a higher impurity removal rate. Copyright © 2017 Elsevier B.V. All rights reserved.

An unconventional method for the recovery of caustic soda from spent Al-rich pickling solutions.

PubMed

Aprea, Paolo; de Gennaro, Bruno; Colella, Carmine

2011-07-01

This work presents an unconventional procedure for the recovery of spent Al-rich caustic soda solutions from the pickling of dies for the production of aluminium extrusions. Caustic soda was regenerated at roughly 70%, by precipitating aluminate, after addition of a silica source, in the form of zeolite A, a microporous material that is widely used in many technological sectors. It was shown that the process is reliable and can be repeated for several cycles, provided the concentration of the caustic soda solution is suitably restored. The by-product obtained, zeolite A, proved to be a high-grade material with performance as a cation exchanger and physical sorbent that is certainly comparable to that reported in literature (e.g., cation exchange capacity equal to 5.14 meq g(-1) vs. 5.48 meq g(-1) and water vapour adsorption capacity of 26.5% vs. 27.6% at 16 torr and 298 K). The economics of the process, although not examined yet, would appear generally favourable, considering that zeolite A is a valuable by-product which widely covers the costs for the recovery of the spent solutions. There are, therefore, significant prospects for the use of zeolite A, particularly as a builder in detergent formulation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Building blocks of a fish head: Developmental and variational modularity in a complex system.

PubMed

Lehoux, Caroline; Cloutier, Richard

2015-11-01

Evolution of the vertebrate skull is developmentally constrained by the interactions among its anatomical systems, such as the dermatocranium and the sensory system. The interaction between the dermal bones and lateral line canals has been debated for decades but their morphological integration has never been tested. An ontogenetic series of 97 juvenile and adult Amia calva (Actinopterygii) was used to describe the patterning and modularity of sensory lateral line canals and their integration with supporting cranial bones. Developmental modules were tested for the otic canal and supratemporal commissure by computing correlations in the branching sequence of groups of pores. Landmarks were digitized on 25 specimens to test a priori hypotheses of variational and developmental modularity at the level of canals and dermal bones. Branching sequence suggests a specific patterning supported by significant positive correlations in the sequence of appearance of branches between bilateral sides. Differences in patterning between the otic canal and the supratemporal commissure and tests of modularity with geometric morphometrics suggest that both canals form distinct modules. The integration between bones and canals was insufficient to detect a module. However, both components were not independent. Groups of pores tended to disappear without affecting other groups of pores suggesting that they are quasi-independent units acting as modules. This study provides evidence of a hierarchical organization for the modular sensory system that could explain variation of pattern of canals among species and their association with dermal bones. © 2015 Wiley Periodicals, Inc.

Commander Young removes CAP from FDF stowage locker on middeck

NASA Technical Reports Server (NTRS)

1981-01-01

Commander Young removes Crew Activity Plans (CAP) from Flight Data File (FD/FDF) modular stowage locker single tray assembly located in forward middeck locker MF28E. Window shade and filter kit on port side bulkhead and potable water tank on middeck floor appear in view. Photo was taken by Pilot Crippen with a 35mm camera.

Privacy-Preserving RFID Authentication Using Public Exponent Three RSA Algorithm

NASA Astrophysics Data System (ADS)

Kim, Yoonjeong; Ohm, Seongyong; Yi, Kang

In this letter, we propose a privacy-preserving authentication protocol with RSA cryptosystem in an RFID environment. For both overcoming the resource restriction and strengthening security, our protocol uses only modular exponentiation with exponent three at RFID tag side, with the padded random message whose length is greater than one-sixth of the whole message length.

A Modular Approach to Video Designation of Manipulation Targets for Manipulators

DTIC Science & Technology

2014-05-12

side view of a ray going through a point cloud of a water bottle sitting on the ground. The bottom left image shows the same point cloud after it has...System (ROS), Point Cloud Library (PCL), and OpenRAVE were used to a great extent to help promote reusability of the code developed during this

Automorphic Forms and Mock Modular Forms in String Theory

NASA Astrophysics Data System (ADS)

Nazaroglu, Caner

We study a variety of modular invariant objects in relation to string theory. First, we focus on Jacobi forms over generic rank lattices and Siegel forms that appear in N = 2, D = 4 compactifications of heterotic string with Wilson lines. Constraints from low energy spectrum and modularity are employed to deduce the relevant supersymmetric partition functions entirely. This procedure is applied on models that lead to Jacobi forms of index 3, 4, 5 as well as Jacobi forms over root lattices A2 and A3. These computations are then checked against an explicit orbifold model which can be Higgsed to the models under question. Models with a single Wilson line are then studied in detail with their relation to paramodular group Gammam as T-duality group made explicit. These results on the heterotic string side are then turned into predictions for geometric invariants using TypeII - Heterotic duality. Secondly, we study theta functions for indenite signature lattices of generic signature. Building on results in literature for signature (n-1,1) and (n-2,2) lattices, we work out the properties of generalized error functions which we call r-tuple error functions. We then use these functions to build such indenite theta functions and describe their modular completions.

Polymer Claw: Instant Underwater Adhesive

DTIC Science & Technology

2012-10-23

April to October. The biofilms included mostly algae with patches of barnacles. 3.1.1 Removal of Biofilm with Caustic Paste The caustic paste was...when the brush was rotated 360° while it was pressed downwards. Figure 3 shows that the thick algae biofilm was completely removed under these...413 TABLE OF CONTENTS 1 SUMMARY 1 2 PROIECT GOALS AND OBJECTIVES 3. 1 KEY ACCOMPLISHMENTS 3 3.1 BIOFILM REMOVAL 3 3.1.1 REMOVAL OF BIOFILM

First Responders Immersive Training Simulation Environment (FRITSE): Scenario Development and Support

DTIC Science & Technology

2014-07-30

consisted of three stages: a deliberate derailment of a train containing either methanol (flammable) or ammonia (caustic) cars at an overpass where...event would be the deliberate release of chemical agent from a van parked near the train derailment and the tertiary event would be a giant fertilizer ...political targets is highest. The derailment would cause a major leak of either caustic ( ammonia ) or highly flammable (methanol) material from derailed

A new approach on Brewer's spent grains treatment and potential use as lignocellulosic yeast cells carriers.

PubMed

Pires, Eduardo J; Ruiz, Héctor A; Teixeira, José A; Vicente, António A

2012-06-13

The major objective of this work is to improve the pretreatments of brewer's spent grains (BSG) aiming at their use as a source for lignocellulosic yeast carriers (LCYC) production. Therefore, several pretreatments of BSG have been designed aiming at obtaining various yeast carriers, differing on their physicochemical composition. Cellulose, hemicellulose, lignin, fat, protein, and ash content were determined for crude BSG and the LCYCs. The long chain fatty acids profile for the crude BSG was also analyzed. Chemical treatments successfully produced several different LCYC based on BSG. The highest cellulose content in LCYC was achieved upon application of caustic (NaOH) treatment during 40 min. Either caustic or combined acid-caustic treatments predominately generated hydrophobic, negatively charged LCYC. The feasibility of using BSG for LCYC production is strengthened by the fact that added-value byproduct can be extracted before the chemical treatments are applied.

Sodium to sodium carbonate conversion process

DOEpatents

Herrmann, Steven D.

1997-01-01

A method of converting radioactive alkali metal into a low level disposable solid waste material. The radioactive alkali metal is atomized and introduced into an aqueous caustic solution having caustic present in the range of from about 20 wt % to about 70 wt % to convert the radioactive alkali metal to a radioactive alkali metal hydroxide. The aqueous caustic containing radioactive alkali metal hydroxide and CO.sub.2 are introduced into a thin film evaporator with the CO.sub.2 present in an amount greater than required to convert the alkali metal hydroxide to a radioactive alkali metal carbonate, and thereafter the radioactive alkali metal carbonate is separated from the thin film evaporator as a dry powder. Hydroxide solutions containing toxic metal hydroxide including one or more metal ions of Sb, As, Ba, Be, Cd, Cr, Pb, Hg, Ni, Se, Ag and T1 can be converted into a low level non-hazardous waste using the thin film evaporator of the invention.

Reducing operating costs for struvite formation with a carbon dioxide stripper.

PubMed

Fattah, K P; Sabrina, N; Mavinic, D S; Koch, F A

2008-01-01

One of the major operational costs of phosphorus recovery as struvite is the cost of caustic chemical that is added to maintain a desired level of operative pH. A study was conducted at the Lulu Island Wastewater Treatment Plant (LIWWTP), Richmond, BC, using a struvite crystallizer and a cascade stripper designed at the University of British Columbia (UBC). The stripper was tested under different operating conditions to determine the effectiveness of CO(2) stripping in increasing the pH of the water matrix and thereby reducing caustic chemical use. This reduction is expected to reduce the operational costs of struvite production. Throughout the project, a high percentage (90%) of phosphorus removal was achieved under each condition. The cascade stripper was very effective in saving caustic usage, ranging from 35% to 86%, depending on the operating conditions. However, the stripper showed relatively poor performance regarding ammonia stripping. Copyright IWA Publishing 2008.

Distributed utility technology cost, performance, and environmental characteristics

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wan, Y; Adelman, S

1995-06-01

Distributed Utility (DU) is an emerging concept in which modular generation and storage technologies sited near customer loads in distribution systems and specifically targeted demand-side management programs are used to supplement conventional central station generation plants to meet customer energy service needs. Research has shown that implementation of the DU concept could provide substantial benefits to utilities. This report summarizes the cost, performance, and environmental and siting characteristics of existing and emerging modular generation and storage technologies that are applicable under the DU concept. It is intended to be a practical reference guide for utility planners and engineers seeking informationmore » on DU technology options. This work was funded by the Office of Utility Technologies of the US Department of Energy.« less

PEP Integrated Test D Run Report Caustic and Oxidative Leaching in UFP-VSL-T02A

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sevigny, Gary J.; Bredt, Ofelia P.; Burns, Carolyn A.

2009-12-11

Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed and operated as part of a plan to respond to issue M12, "Undemonstrated Leaching Processes" of the External Flowsheet Review Team (EFRT) issue response plan. The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. Themore » PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing. Two operating scenarios are currently being evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario (Test B and D) has caustic leaching performed in the UFP-2 ultrafiltration feed vessels (i.e., vessel UFP-VSL-T02A in the PEP and vessels UFP-VSL-00002A and B in the WTP PTF). The second scenario (Test A) has caustic leaching conducted in the UFP-1 ultrafiltration feed preparation vessels (i.e., vessels UFP-VSL-T01A and B in the PEP and vessels UFP VSL-00001A and B in the WTP PTF). In Test D, 19M sodium hydroxide (NaOH, caustic) was added to the waste slurry in the UFP VSL T02 vessel after the solids were concentrated to ~20% undissolved solids. The NaOH was added to leach solid aluminum compounds (e.g., gibbsite, boehmite). Caustic addition is followed by heating to 85°C using direct injection of steam to accelerate the leach process. The main difference of Test D compared to Test B is that the leach temperature is 85°C for 24 hrs as compared to 100°C for 12 hours. The other difference is the Test D simulant had Cr in the simulant from the start of processing and Test B had Cr added to adjust the simulant composition after aluminum leaching. Following the caustic leach, the UFP-VSL-T02A vessel contents are cooled using the vessel cooling jacket. The slurry was then concentrated to 17 wt% undissolved solids and washed with inhibited water to remove NaOH and other soluble salts. Next, the slurry was oxidatively leached using sodium permanganate to solubilize chrome. The slurry was then washed to remove the dissolved chrome and concentrated.« less

Conditional solvation thermodynamics of isoleucine in model peptides and the limitations of the group-transfer model.

PubMed

Tomar, Dheeraj S; Weber, Valéry; Pettitt, B Montgomery; Asthagiri, D

2014-04-17

The hydration thermodynamics of the amino acid X relative to the reference G (glycine) or the hydration thermodynamics of a small-molecule analog of the side chain of X is often used to model the contribution of X to protein stability and solution thermodynamics. We consider the reasons for successes and limitations of this approach by calculating and comparing the conditional excess free energy, enthalpy, and entropy of hydration of the isoleucine side chain in zwitterionic isoleucine, in extended penta-peptides, and in helical deca-peptides. Butane in gauche conformation serves as a small-molecule analog for the isoleucine side chain. Parsing the hydrophobic and hydrophilic contributions to hydration for the side chain shows that both of these aspects of hydration are context-sensitive. Furthermore, analyzing the solute-solvent interaction contribution to the conditional excess enthalpy of the side chain shows that what is nominally considered a property of the side chain includes entirely nonobvious contributions of the background. The context-sensitivity of hydrophobic and hydrophilic hydration and the conflation of background contributions with energetics attributed to the side chain limit the ability of a single scaling factor, such as the fractional solvent exposure of the group in the protein, to map the component energetic contributions of the model-compound data to their value in the protein. But ignoring the origin of cancellations in the underlying components the group-transfer model may appear to provide a reasonable estimate of the free energy for a given error tolerance.

LFER Studies Evaluating Solvent Effects on an α-Chloro-and two β,β,β-Trichloro-Ethyl Chloroformate Esters

PubMed Central

D’Souza, Malcolm J.; Sandosky, Brandon; Fernandez-Bueno, Gabriel A.; McAneny, Matthew J.; Kevill, Dennis N.

2014-01-01

To provide insight and to identify the occurrence of mechanistic changes in relation to variance in solvent-type, the solvent effects on the rates of solvolysis of three substrates, 2,2,2-trichloro-1,1-dimethylethyl chloroformate, 2,2,2-trichloroethyl chloroformate, and 1-chloroethyl chloroformate, are analyzed using linear free energy relationships (LFERs) such as the extended Grunwald-Winstein equation, and a similarity-based LFER model approach that is based on the solvolysis of phenyl chloroformate. At 25.0 °C, in four common solvents, the α-chloroethyl chloroformate was found to react considerably faster than the two β,β,β-trichloro-substituted analogs. This immense rate enhancement can be directly related to the proximity of the electron-withdrawing α-chlorine atom to the carbonyl carbon reaction center. In the thirteen solvents studied, 1-chloroethyl chloroformate was found to strictly follow a carbonyl addition process, with the addition-step being rate-determining. For the two β,β,β-trichloro-substrates, in aqueous mixtures that are very rich in a fluoroalcohol component, there is compelling evidence for the occurrence of side-by-side addition-elimination and ionization mechanisms, with the ionization pathway being predominant. The presence of the two methyl groups on the α-carbon of 2,2,2-trichloro-1,1-dimethylethyl chloroformate has additive steric and stereoelectronic implications, causing its rate of reaction to be significantly slower than that of 2,2,2-trichloroethyl chloroformate. PMID:24812595

Self-assembly mechanism of 1,3:2,4-di(3,4-dichlorobenzylidene)-D-sorbitol and control of the supramolecular chirality.

PubMed

Li, Jingjing; Fan, Kaiqi; Guan, Xidong; Yu, Yingzhe; Song, Jian

2014-11-11

Dibenzylidene-D-sorbitol (DBS) and its derivatives are known to form gels in organic solvents; however, the mechanism of the gel formation has been a subject of much debate. The present work is undertaken to elucidate the organization mechanism of a DBS derivative, 1,3:2,4-di(3,4-dichlorobenzylidene)-D-sorbitol (DCDBS), by taking into account the solvent effects and comparing the experiment data with theoretical calculation. These molecules form smooth nonhelical fibers with a rest circular dichroism (CD) signal in polar solvents, in contrast to rope-liked left-helical fibers with a strong negative CD signal observed in nonpolar solvents. The molecular complexes thus formed were characterized by means of Fourier transform infrared spectra, ultraviolet-visible spectra, X-ray diffraction patterns, static contact angles, and theoretical calculations. It was proposed that the interactions between the gelator and the solvents could subtly change the stacking of the molecules and hence their self-assembled nanostructures. In nonpolar solvents, the gelator molecules appear as a distorted T-shaped structure with the 6-OH forming intermolecular hydrogen bonds with the acetal oxygens of adjacent gelator molecule. In addition, because of differential stacking interactions on both sides of the 10-member ring skeleton of the gelator, the oligomers may assemble in a helix fashion to minimize the energy, leading to helical fibers. In polar solvents, however, the gelator molecules show a rigid planelike structure and thus stack on top of each other because of strong parallel-displaced π interactions. The balanced driving force on both sides of the 10-member ring skeleton made it difficult for the dimers to bend, thus resulting in nonhelical nanostructure. As expected from the mechanisms proposed here, twisted ribbon fibers with a medium strength CD signal were obtained when solvents of different polarities were mixed. Thus, solvent effects revealed in this work represent an effective means of realizing in situ tuning of nanostructures and control of the expression of chirality at supramolecular levels.

Metal-doped organic foam

DOEpatents

Rinde, James A.

1982-01-01

Organic foams having a low density and very small cell size and method for producing same in either a metal-loaded or unloaded (nonmetal loaded) form are described. Metal-doped foams are produced by soaking a polymer gel in an aqueous solution of desired metal salt, soaking the gel successively in a solvent series of decreasing polarity to remove water from the gel and replace it with a solvent of lower polarity with each successive solvent in the series being miscible with the solvents on each side and being saturated with the desired metal salt, and removing the last of the solvents from the gel to produce the desired metal-doped foam having desired density cell size, and metal loading. The unloaded or metal-doped foams can be utilized in a variety of applications requiring low density, small cell size foam. For example, rubidium-doped foam made in accordance with the invention has utility in special applications, such as in x-ray lasers.

Enthalpy characteristics of the dissolution of L-valine in water/formamide mixtures at 298.15 K

NASA Astrophysics Data System (ADS)

Smirnov, V. I.; Badelin, V. G.

2016-11-01

The thermochemical dissolution of L-valine in solvent mixtures H2O + (formamide, N-methylformamide, and N, N-dimethylformamide) is studied at an organic component concentration of x 2 = 0-0.35 molar fractions and a temperature of 298.15 K. The experimental data are used to calculate standard enthalpies of dissolution, the transferring of L-valine from water to a mixed solvent, and the enthalpy coefficients of pairwise interactions ( h xy ) with organic solvent molecules. The correlation between the enthalpy characteristics of the dissolution of L-valine with the composition of aqueous organic mixtures and the nature of the organic solvent (its physicochemical properties) is determined. A comparative analysis of the values of h xy of a number of aliphatic L-amino acids in similar solvent mixtures with the hydrophobicity parameters of their side chains is performed.

Proceedings of the Technology Transfer Seminar/Workshop on the Application of Pollution Abatement Technology to Local Governments

DTIC Science & Technology

1975-05-01

civil agencies through interage..:y agreements. One of the Navy field activities, the Naval Ammunition Depot at Crane , Indiana, has developed rather...chemical mixing compartment and chem- ical dosing tank assures adequate contact time. Solids and organics are hydrolyzed by the caustic , while the...The high caustic level of the treated waste water resulted in corrosion to various points in the system. Pumps required extensive weekly maintenance

Analysis of Deep Seafloor Arrivals Observed on NPAL04

DTIC Science & Technology

2012-12-03

transmission station to the scattering point (black line) to compute the time spent on the PE-predicted path to the scattering point. This time would...arrives at the OBSs at times corresponding to caustics of the PE predicted time fronts, there are large amplitude, late arrivals that occur between... caustics and even after the PE predicted coda. Similar analysis was done for T500 to T2300 with similar results and is discussed in Section 4 of

The Effects of Internal Tides on Acoustic Propagation in the Philippine Sea

DTIC Science & Technology

2013-09-01

understanding during the long days spent away from home while working on this thesis xvi THIS PAGE INTENTIONALLY LEFT BLANK 1 I. INTRODUCTION...sweeping by a vertical set of receivers at a fixed range. Each wavefront branch is seen as the line between caustics (acoustic focusing points where...the ray folds), and is composed of eigenrays with the same ID. The caustics farthest to the left of the timefront plot represent the rays with large

Hazardous Waste Minimization Initiation Decision Report. Volume 1

DTIC Science & Technology

1988-06-01

different treatment and disposal practices for spent caustic materials. In some cases, the material is placed in drums and sent to DRMO for disposal or to a...often available. As at some Navy facilities, waste caustic may be neutralized with spent acid at the process line with the effluent sent to the IWTP...3-111 PART II - Spent Battery Electrolyte .... 3-112 PART III- Battery Acid Sludges ........ 3-113 3.13.3 Disposal of Wastes from Battery Repair and

Commandant’s International Technical Series. Volume 9. International Regulations on the Prevention of Pollution from Ships Carrying Hazardous Chemicals in Bulk.

DTIC Science & Technology

1985-12-01

Styrene monomer 2055 B Sulphuric acid 1830 C " Sulphuric acid, spent 1832 C - Sulphurous acid 1633 (C) Sunflover oil D...anhydrides (e.g. formic, acetic); .3 halogenated carboxylic acids (e.g. chloracetic); .4 sulpnonic acids (e.g. benzene sulphonic); .5 caustic alkalis...acetic); (iii) halogenated carboxylic acids (e.g. cbloracetic); (iv) sulphonic acids (e.g. benzene sulphonic);II (v) caustic alkalis (e.g. sodium

Left colonic graft in esophageal reconstruction for caustic stricture: mortality and morbidity.

PubMed

Boukerrouche, A

2013-01-01

The adequacy of the blood supply to the left colon graft and its ability to transport food effectively from pharynx to stomach made it an esophageal substitute of choice, particularly in esophageal caustic stricture. From 1999 to 2009, 60 patients underwent colon interposition for esophageal caustic stricture (n= 57) and cancer (n= 3). An isoperistaltic colonic graft based on the left colonic artery could be used in all of these patients. The substernal route was used exclusively, and upper thoracic inlet was opened when necessary. The isoperistaltic left colonic graft interposed by substernal route represents the surgical procedure of choice in all operations performed for esophageal substitution during the study period. The operative mortality rate was 3.3%. A cervical fistula occurred in 10 patients (16.6%) and cervical anastomotic stricture in five patients (8.3%). Dilation was required in all the stricture of the esophageal colonic anastomosis with good response. The isoperistaltic left colic transplant supplied by the left colic pedicle is an excellent long-term replacement organ for the esophageal caustic stenosis. When performed by experienced surgeons, the left isoperistaltic esophagocoloplasty is a satisfactory surgical method for esophageal reconstruction with acceptable early morbidity and good long-term functional results. © 2012 Copyright the Authors. Journal compilation © 2012, Wiley Periodicals, Inc. and the International Society for Diseases of the Esophagus.

Machine learning of single molecule free energy surfaces and the impact of chemistry and environment upon structure and dynamics

NASA Astrophysics Data System (ADS)

Mansbach, Rachael A.; Ferguson, Andrew L.

2015-03-01

The conformational states explored by polymers and proteins can be controlled by environmental conditions (e.g., temperature, pressure, and solvent) and molecular chemistry (e.g., molecular weight and side chain identity). We introduce an approach employing the diffusion map nonlinear machine learning technique to recover single molecule free energy landscapes from molecular simulations, quantify changes to the landscape as a function of external conditions and molecular chemistry, and relate these changes to modifications of molecular structure and dynamics. In an application to an n-eicosane chain, we quantify the thermally accessible chain configurations as a function of temperature and solvent conditions. In an application to a family of polyglutamate-derivative homopeptides, we quantify helical stability as a function of side chain length, resolve the critical side chain length for the helix-coil transition, and expose the molecular mechanisms underpinning side chain-mediated helix stability. By quantifying single molecule responses through perturbations to the underlying free energy surface, our approach provides a quantitative bridge between experimentally controllable variables and microscopic molecular behavior, guiding and informing rational engineering of desirable molecular structure and function.

Machine learning of single molecule free energy surfaces and the impact of chemistry and environment upon structure and dynamics.

PubMed

Mansbach, Rachael A; Ferguson, Andrew L

2015-03-14

The conformational states explored by polymers and proteins can be controlled by environmental conditions (e.g., temperature, pressure, and solvent) and molecular chemistry (e.g., molecular weight and side chain identity). We introduce an approach employing the diffusion map nonlinear machine learning technique to recover single molecule free energy landscapes from molecular simulations, quantify changes to the landscape as a function of external conditions and molecular chemistry, and relate these changes to modifications of molecular structure and dynamics. In an application to an n-eicosane chain, we quantify the thermally accessible chain configurations as a function of temperature and solvent conditions. In an application to a family of polyglutamate-derivative homopeptides, we quantify helical stability as a function of side chain length, resolve the critical side chain length for the helix-coil transition, and expose the molecular mechanisms underpinning side chain-mediated helix stability. By quantifying single molecule responses through perturbations to the underlying free energy surface, our approach provides a quantitative bridge between experimentally controllable variables and microscopic molecular behavior, guiding and informing rational engineering of desirable molecular structure and function.

Shuttle active thermal control system development testing. Volume 3: Modular radiator system test data correlation with thermal model

NASA Technical Reports Server (NTRS)

Phillips, M. A.

1973-01-01

Results are presented of an analysis which compares the performance predictions of a thermal model of a multi-panel modular radiator system with thermal vacuum test data. Comparisons between measured and predicted individual panel outlet temperatures and pressure drops and system outlet temperatures have been made over the full range of heat loads, environments and plumbing arrangements expected for the shuttle radiators. Both two sided and one sided radiation have been included. The model predictions show excellent agreement with the test data for the maximum design conditions of high load and hot environment. Predictions under minimum design conditions of low load-cold environments indicate good agreement with the measured data, but evaluation of low load predictions should consider the possibility of parallel flow instabilities due to main system freezing. Performance predictions under intermediate conditions in which the majority of the flow is not in either the main or prime system are adequate although model improvements in this area may be desired. The primary modeling objective of providing an analytical technique for performance predictions of a multi-panel radiator system under the design conditions has been met.

Quantifying side-chain conformational variations in protein structure

PubMed Central

Miao, Zhichao; Cao, Yang

2016-01-01

Protein side-chain conformation is closely related to their biological functions. The side-chain prediction is a key step in protein design, protein docking and structure optimization. However, side-chain polymorphism comprehensively exists in protein as various types and has been long overlooked by side-chain prediction. But such conformational variations have not been quantitatively studied and the correlations between these variations and residue features are vague. Here, we performed statistical analyses on large scale data sets and found that the side-chain conformational flexibility is closely related to the exposure to solvent, degree of freedom and hydrophilicity. These analyses allowed us to quantify different types of side-chain variabilities in PDB. The results underscore that protein side-chain conformation prediction is not a single-answer problem, leading us to reconsider the assessment approaches of side-chain prediction programs. PMID:27845406

Quantifying side-chain conformational variations in protein structure

NASA Astrophysics Data System (ADS)

Miao, Zhichao; Cao, Yang

2016-11-01

Protein side-chain conformation is closely related to their biological functions. The side-chain prediction is a key step in protein design, protein docking and structure optimization. However, side-chain polymorphism comprehensively exists in protein as various types and has been long overlooked by side-chain prediction. But such conformational variations have not been quantitatively studied and the correlations between these variations and residue features are vague. Here, we performed statistical analyses on large scale data sets and found that the side-chain conformational flexibility is closely related to the exposure to solvent, degree of freedom and hydrophilicity. These analyses allowed us to quantify different types of side-chain variabilities in PDB. The results underscore that protein side-chain conformation prediction is not a single-answer problem, leading us to reconsider the assessment approaches of side-chain prediction programs.

Quantifying side-chain conformational variations in protein structure.

PubMed

Miao, Zhichao; Cao, Yang

2016-11-15

Protein side-chain conformation is closely related to their biological functions. The side-chain prediction is a key step in protein design, protein docking and structure optimization. However, side-chain polymorphism comprehensively exists in protein as various types and has been long overlooked by side-chain prediction. But such conformational variations have not been quantitatively studied and the correlations between these variations and residue features are vague. Here, we performed statistical analyses on large scale data sets and found that the side-chain conformational flexibility is closely related to the exposure to solvent, degree of freedom and hydrophilicity. These analyses allowed us to quantify different types of side-chain variabilities in PDB. The results underscore that protein side-chain conformation prediction is not a single-answer problem, leading us to reconsider the assessment approaches of side-chain prediction programs.

Process for converting sodium nitrate-containing, caustic liquid radioactive wastes to solid insoluble products

DOEpatents

Barney, Gary S.; Brownell, Lloyd E.

1977-01-01

A method for converting sodium nitrate-containing, caustic, radioactive wastes to a solid, relatively insoluble, thermally stable form is provided and comprises the steps of reacting powdered aluminum silicate clay, e.g., kaolin, bentonite, dickite, halloysite, pyrophyllite, etc., with the sodium nitrate-containing radioactive wastes which have a caustic concentration of about 3 to 7 M at a temperature of 30.degree. C to 100.degree. C to thereby entrap the dissolved radioactive salts in the aluminosilicate matrix. In one embodiment the sodium nitrate-containing, caustic, radioactive liquid waste, such as neutralized Purex-type waste, or salts or oxide produced by evaporation or calcination of these liquid wastes (e.g., anhydrous salt cake) is converted at a temperature within the range of 30.degree. C to 100.degree. C to the solid mineral form-cancrinite having an approximate chemical formula 2(NaAlSiO.sub.4) .sup.. xSalt.sup.. y H.sub.2 O with x = 0.52 and y = 0.68 when the entrapped salt is NaNO.sub.3. In another embodiment the sodium nitrate-containing, caustic, radioactive liquid is reacted with the powdered aluminum silicate clay at a temperature within the range of 30.degree. C to 100.degree. C, the resulting reaction product is air dried eitheras loose powder or molded shapes (e.g., bricks) and then fired at a temperature of at least 600.degree. C to form the solid mineral form-nepheline which has the approximate chemical formula of NaAlSiO.sub.4. The leach rate of the entrapped radioactive salts with distilled water is reduced essentially to that of the aluminosilicate lattice which is very low, e.g., in the range of 10.sup.-.sup.2 to 10.sup.-.sup.4 g/cm.sup.2 -- day for cancrinite and 10.sup.-.sup.3 to 10.sup.-.sup.5 g/cm.sup.2 -- day for nepheline.

Method of making a modular off-axis solar concentrator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Plesniak, Adam P.; Hall, John C.

A method of making a solar concentrator may include forming a receiving wall having an elongated wall, a first side wall and a second side wall; attaching the first side wall and the second side wall to a reflecting wall to form a housing having an internal volume with an opening; forming a lip on the receiving wall and the reflecting wall; attaching a cover to the receiving wall and the reflecting wall at the lip to seal the opening into the internal volume, thereby creating a rigid structure; and mounting at least one receiver having at least one photovoltaicmore » cell on the elongated wall to receive solar radiation entering the housing and reflected by the receiving wall, the receiver having an axis parallel with a surface normal of the photovoltaic cell, such that the axis is disposed at a non-zero angle relative to the vertical axis of the opening.« less

Sonic boom measurements from accelerating supersonic tracked sleds

NASA Technical Reports Server (NTRS)

Reed, J. W.

1974-01-01

Supersonic sled tests on the Sandia 1524-m (5000-ft) track generate sonic booms of sufficient intensity to allow some airblast measurements at distance scales not obtained from wind tunnel or flight tests. During acceleration, an emitted curved boom wave propagates to a caustic, or focus. Detailed measurements around these caustics may help to clarify the overpressure magnification which can occur from real aircraft operations. Six fixed pressure gages have been operated to document the general noise field, and a mobile array of twelve gages.

[Poisoning by household products].

PubMed

Lambert, H; Manel, J; Gabrion, I

2000-02-15

Caustic products are responsible for the most serious cases of poisoning, which are always emergency cases. Application of current intervention procedures has decreased both morbidity and mortality. Water-diluted bleach, the ingestion of which remains extremely frequent, is a moderate irritant rather than a caustic product. Emission of gas produced when mixing bleach with other agents can be responsible for choking gas poisoning. Anionic and nonionic detergents are mostly dangerous because of their foam-producing properties. Mercury vapours and methanol are other potentially hazardous products.

Wave Chaos and HPM Effects on Electronic Systems

DTIC Science & Technology

2013-08-13

if one examines these pas- sages, one will find that, as the orbit length approaches infinity, (i) the fraction of time spent by the orbit in the...as the orbits in a complete quarter circle billiard having the same radius R (see Fig. 3.2(a)). These orbits are tangent to a circular caustic 62 with...a radius Cr. If the caustic radius Cr > ρ0, (see Fig. 3.1) this orbit is trapped in the cap, and is integrable. There are also chaotic orbits that

Minutes of the Explosives Safety Seminar (25th) Held in Anaheim, California on 18-20 August 1992. Volume 1

DTIC Science & Technology

1992-08-20

project. There is no doubt that we would have otherwise spent many years in proving project feasibility and trialing the specific demilitarisation...SUCH ROCKET MOTORS AS THE ONE USED IN THE BULLPUP SYSTEM WERE CONSIDERED. A. DRAINING AND NEUTRALIZING THE OXIDIZER BY CAUSTIC SODA AND THEN SIMPLE...INHIBITED RED FUMING NITRIC ACID WAS DETECTED IN SMALL AMOUNTS. 482 CONSEQUENTLY. THE "EMPTY" CASES WERE PLACED INTO A TANK CONTAINING WATER AND CAUSTIC

A modular synthesis of teraryl-based α-helix mimetics, part 1: Synthesis of core fragments with two electronically differentiated leaving groups.

PubMed

Peters, Martin; Trobe, Melanie; Tan, Hao; Kleineweischede, Rolf; Breinbauer, Rolf

2013-02-11

Teraryl-based α-helix mimetics have proven to be useful compounds for the inhibition of protein-protein interactions (PPI). We have developed a modular and flexible approach for the synthesis of teraryl-based α-helix mimetics. Central to our strategy is the use of a benzene core unit featuring two leaving groups of differentiated reactivity in the Pd-catalyzed cross-coupling used for terphenyl assembly. With the halogen/diazonium route and the halogen/triflate route, two strategies have successfully been established. The synthesis of core building blocks with aliphatic (Ala, Val, Leu, Ile), aromatic (Phe), polar (Cys, Lys), hydrophilic (Ser, Gln), and acidic (Glu) amino acid side chains are reported. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Localized conformational interrogation of antibody and antibody-drug conjugates by site-specific carboxyl group footprinting.

PubMed

Pan, Lucy Yan; Salas-Solano, Oscar; Valliere-Douglass, John F

Establishing and maintaining conformational integrity of monoclonal antibodies (mAbs) and antibody-drug conjugates (ADCs) during development and manufacturing is critical for ensuring their clinical efficacy. As presented here, we applied site-specific carboxyl group footprinting (CGF) for localized conformational interrogation of mAbs. The approach relies on covalent labeling that introduces glycine ethyl ester tags onto solvent-accessible side chains of protein carboxylates. Peptide mapping is used to monitor the labeling kinetics of carboxyl residues and the labeling kinetics reflects the conformation or solvent-accessibility of side chains. Our results for two case studies are shown here. The first study was aimed at defining the conformational changes of mAbs induced by deglycosylation. We found that two residues in C H 2 domain (D268 and E297) show significantly enhanced side chain accessibility upon deglycosylation. This site-specific result highlighted the advantage of monitoring the labeling kinetics at the amino acid level as opposed to the peptide level, which would result in averaging out of highly localized conformational differences. The second study was designed to assess conformational effects brought on by conjugation of mAbs with drug-linkers. All 59 monitored carboxyl residues displayed similar solvent-accessibility between the ADC and mAb under native conditions, which suggests the ADC and mAb share similar side chain conformation. The findings are well correlated and complementary with results from other assays. This work illustrated that site-specific CGF is capable of pinpointing local conformational changes in mAbs or ADCs that might arise during development and manufacturing. The methodology can be readily implemented within the industry to provide comprehensive conformational assessment of these molecules.

Dual-component system dimethyl sulfoxide/LiCl as a solvent and catalyst for homogeneous ring-opening grafted polymerization of ε-caprolactone onto xylan.

PubMed

Zhang, Xue-Qin; Chen, Ming-Jie; Liu, Chuan-Fu; Sun, Run-Cang

2014-01-22

The preparation of xylan-graft-poly(ε-caprolactone) (xylan-g-PCL) copolymers was investigated by homogeneous ring-opening polymerization (ROP) in a dual-component system containing Lewis base LiCl and strong polar aprotic solvent dimethyl sulfoxide (DMSO). DMSO/LiCl acted as solvent, base, and catalyst for the ROP reaction. The effects of the parameters, including the reaction temperature, molar ratio of ε-caprolactone (ε-CL) to anhydroxylose units (AXU) in xylan, and reaction time, on the degree of substitution (DS) and weight percent of PCL side chain (WPCL) were investigated. The results showed that xylan-g-PCL copolymers with low DS in the range of 0.03-0.39 were obtained under the given conditions. The Fourier transform infrared spectroscopy (FTIR), (1)H nuclear magnetic resonance (NMR), (13)C NMR, (1)H-(1)H correlation spectroscopy (COSY), and (1)H-(13)C correlation two-dimensional (2D) NMR [heteronuclear single-quantum coherence (HSQC)] characterization provided more evidence of the attachment of side chains onto xylan. Only one ε-CL was confirmed to be attached onto xylan with each side chain. Integration of resonances assigned to the substituted C2 and C3 in the HSQC spectrum also indicated 69.23 and 30.77% of PCL side chains attached to AXU at C3 and C2 positions, respectively. Although the attachment of PCL onto xylan led to the decreased thermal stability of xylan, the loss of unrecovered xylan fractions with low molecular weight because of the high solubility of xylan in DMSO/LiCl resulted in the increased thermal stability of the samples. This kind of xylan derivative has potential application in environmentally friendly and biodegradable materials considering the good biodegradability of xylan and PCL.

Conditional Solvation Thermodynamics of Isoleucine in Model Peptides and the Limitations of the Group-Transfer Model

PubMed Central

2015-01-01

The hydration thermodynamics of the amino acid X relative to the reference G (glycine) or the hydration thermodynamics of a small-molecule analog of the side chain of X is often used to model the contribution of X to protein stability and solution thermodynamics. We consider the reasons for successes and limitations of this approach by calculating and comparing the conditional excess free energy, enthalpy, and entropy of hydration of the isoleucine side chain in zwitterionic isoleucine, in extended penta-peptides, and in helical deca-peptides. Butane in gauche conformation serves as a small-molecule analog for the isoleucine side chain. Parsing the hydrophobic and hydrophilic contributions to hydration for the side chain shows that both of these aspects of hydration are context-sensitive. Furthermore, analyzing the solute–solvent interaction contribution to the conditional excess enthalpy of the side chain shows that what is nominally considered a property of the side chain includes entirely nonobvious contributions of the background. The context-sensitivity of hydrophobic and hydrophilic hydration and the conflation of background contributions with energetics attributed to the side chain limit the ability of a single scaling factor, such as the fractional solvent exposure of the group in the protein, to map the component energetic contributions of the model-compound data to their value in the protein. But ignoring the origin of cancellations in the underlying components the group-transfer model may appear to provide a reasonable estimate of the free energy for a given error tolerance. PMID:24650057

A microfluidic study of liquid-liquid extraction mediated by carbon dioxide.

PubMed

Lestari, Gabriella; Salari, Alinaghi; Abolhasani, Milad; Kumacheva, Eugenia

2016-07-05

Liquid-liquid extraction is an important separation and purification method; however, it faces a challenge in reducing the energy consumption and the environmental impact of solvent (extractant) recovery. The reversible chemical reactions of switchable solvents (nitrogenous bases) with carbon dioxide (CO2) can be implemented in reactive liquid-liquid extraction to significantly reduce the cost and energy requirements of solvent recovery. The development of new effective switchable solvents reacting with CO2 and the optimization of extraction conditions rely on the ability to evaluate and screen the performance of switchable solvents in extraction processes. We report a microfluidic strategy for time- and labour-efficient studies of CO2-mediated solvent extraction. The platform utilizes a liquid segment containing an aqueous extractant droplet and a droplet of a solution of a switchable solvent in a non-polar liquid, with gaseous CO2 supplied to the segment from both sides. Following the reaction of the switchable solvent with CO2, the solvent becomes hydrophilic and transfers from the non-polar solvent to the aqueous droplet. By monitoring the time-dependent variation in droplet volumes, we determined the efficiency and extraction time for the CO2-mediated extraction of different nitrogenous bases in a broad experimental parameter space. The platform enables a significant reduction in the amount of switchable solvents used in these studies, provides accurate temporal characterization of the liquid-liquid extraction process, and offers the capability of high-throughput screening of switchable solvents.

Large scale micro-photometry for high resolution pH-characterization during electro-osmotic pumping and modular micro-swimming

NASA Astrophysics Data System (ADS)

Niu, Ran; Khodorov, Stanislav; Weber, Julian; Reinmüller, Alexander; Palberg, Thomas

2017-11-01

Micro-fluidic pumps as well as artificial micro-swimmers are conveniently realized exploiting phoretic solvent flows based on local gradients of temperature, electrolyte concentration or pH. We here present a facile micro-photometric method for monitoring pH gradients and demonstrate its performance and scope on different experimental situations including an electro-osmotic pump and modular micro-swimmers assembled from ion exchange resin beads and polystyrene colloids. In combination with the present microscope and DSLR camera our method offers a 2 μm spatial resolution at video frame rate over a field of view of 3920 × 2602 μm2. Under optimal conditions we achieve a pH-resolution of 0.05 with about equal contributions from statistical and systematical uncertainties. Our quantitative micro-photometric characterization of pH gradients which develop in time and reach out several mm is anticipated to provide valuable input for reliable modeling and simulations of a large variety of complex flow situations involving pH-gradients including artificial micro-swimmers, microfluidic pumping or even electro-convection.

SALTSTONE VAULT CLASSIFICATION SAMPLES MODULAR CAUSTIC SIDE SOLVENT EXTRACTION UNIT/ACTINIDE REMOVAL PROCESS WASTE STREAM APRIL 2011

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eibling, R.

Savannah River National Laboratory (SRNL) was asked to prepare saltstone from samples of Tank 50H obtained by SRNL on April 5, 2011 (Tank 50H sampling occurred on April 4, 2011) during 2QCY11 to determine the non-hazardous nature of the grout and for additional vault classification analyses. The samples were cured and shipped to Babcock & Wilcox Technical Services Group-Radioisotope and Analytical Chemistry Laboratory (B&W TSG-RACL) to perform the Toxic Characteristic Leaching Procedure (TCLP) and subsequent extract analysis on saltstone samples for the analytes required for the quarterly analysis saltstone sample. In addition to the eight toxic metals - arsenic, barium,more » cadmium, chromium, mercury, lead, selenium and silver - analytes included the underlying hazardous constituents (UHC) antimony, beryllium, nickel, and thallium which could not be eliminated from analysis by process knowledge. Additional inorganic species determined by B&W TSG-RACL include aluminum, boron, chloride, cobalt, copper, fluoride, iron, lithium, manganese, molybdenum, nitrate/nitrite as Nitrogen, strontium, sulfate, uranium, and zinc and the following radionuclides: gross alpha, gross beta/gamma, 3H, 60Co, 90Sr, 99Tc, 106Ru, 106Rh, 125Sb, 137Cs, 137mBa, 154Eu, 238Pu, 239/240Pu, 241Pu, 241Am, 242Cm, and 243/244Cm. B&W TSG-RACL provided subsamples to GEL Laboratories, LLC for analysis for the VOCs benzene, toluene, and 1-butanol. GEL also determines phenol (total) and the following radionuclides: 147Pm, 226Ra and 228Ra. Preparation of the 2QCY11 saltstone samples for the quarterly analysis and for vault classification purposes and the subsequent TCLP analyses of these samples showed that: (1) The saltstone waste form disposed of in the Saltstone Disposal Facility in 2QCY11 was not characteristically hazardous for toxicity. (2) The concentrations of the eight RCRA metals and UHCs identified as possible in the saltstone waste form were present at levels below the UTS. (3) Most of the inorganic species measured in the leachate do not exceed the MCL, SMCL or TW limits. (4) The inorganic waste species that exceeded the MCL by more than a factor of 10 were nitrate, nitrite and the sum of nitrate and nitrite. (5) Analyses met all quality assurance specifications of US EPA SW-846. (6) The organic species (benzene, toluene, 1-butanol, phenol) were either not detected or were less than reportable for the vault classification samples. (7) The gross alpha and radium isotopes could not be determined to the MCL because of the elevated background which raised the detection limits. (8) Most of the beta/gamma activity was from 137Cs and its daughter 137mBa. (9) The concentration of 137Cs and 90Sr were present in the leachate at concentrations 1/40th and 1/8th respectively than in the 2003 vault classification samples. The saltstone waste form placed in the Saltstone Disposal Facility in 2QCY11 met the SCHWMR R.61-79.261.24(b) RCRA metals requirements for a nonhazardous waste form. The TCLP leachate concentrations for nitrate, nitrite and the sum of nitrate and nitrite were greater than 10x the MCLs in SCDHEC Regulations R.61-107.19, Part I A, which confirms the Saltstone Disposal Facility classification as a Class 3 Landfill. The saltstone waste form placed in the Saltstone Disposal Facility in 2QCY11 met the R.61-79.268.48(a) non wastewater treatment standards.« less

Molluscum contagiosum: A novel Ayurvedic approach.

PubMed

Kalasannavar, Shivanand B; Sawalgimath, Mahesh P

2013-07-01

Three cases of molluscum contagiosum (MC) approached our outpatient Department of Dermatology complaining of umbilicated, skin-colored, firm, painless papules over the neck and face. All of them were immune competent. The medical, social, and family history was insignificant. The lesions were, numerous and recurrent. However, MC in healthy people is a self-limiting disease, but it will take about 18 months to resolve by its own. Hence, the treatment becomes necessary to accelerate the healing process, preventing its spread and for cosmetic reasons. Most of the contemporary treatment methods such as cryotherapy, curettage, and topical application of caustic agents are effective but produce local side-effects such as erythema, tenderness, itching, burning sensation, and pain. The present study reports the efficacy of external application of Pratisaraṇīya Kṇāra (the type of Alkali used for smearing over the affected area) and Bilvādi Agada tablet orally in three cases, which yielded encouraging results.

Susceptibility of steam generator tubes in secondary conditions: Effects of lead and sulphate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gomez Briceno, D.; Garcia, M.S.; Castano, M.L.

1997-02-01

IGA/SCC on the secondary side of steam generators is increasing every year, and represents the cause of some steam generator replacements. Until recently, caustic and acidic environments have been accepted as causes of IGA/SCC, particulary in certain environments: in sludge pile on the tube sheet; at support crevices; in free span. Lead and sulfur have been identified as significant impurities. Present thoughts are that some IGA/SCC at support crevices may have occurred in nearly neutral or mildly alkaline environments. Here the authors present experimental work aimed at studying the influence of lead and sulfur on the behaviour of steam generatormore » tube alloys in different water environments typical of steam generators. Most test results ran for at least 2000 hours, and involved visual and detailed surface analysis during and following the test procedures.« less

Venus Atmospheric Exploration by Solar Aircraft

NASA Technical Reports Server (NTRS)

Landis, Geoffrey A.; LaMarre, C.; Colozza, A.

2002-01-01

The Venus atmosphere is a favorable environment for flying powered aircraft. The atmospheric pressure makes flight much easier than on planets such as Mars. Above the clouds, solar energy is available in abundance on Venus, and the slow rotation of Venus allows a solar airplane to be designed for flight within continuous sunlight. The atmosphere between 50 km and 75 km on Venus is one of the most dynamic and interesting regions of the planet. The challenge for a Venus aircraft will be the fierce winds and caustic atmosphere. In order to remain on the sunlit side of Venus, an exploration aircraft will have to be capable of sustained flight at or above the wind speed. An aircraft would be a powerful tool for exploration. By learning how Venus can be so similar to Earth, and yet so different, we will learn to better understand the climate and geological history of the Earth.

Molluscum contagiosum: A novel Ayurvedic approach

PubMed Central

Kalasannavar, Shivanand B.; Sawalgimath, Mahesh P.

2013-01-01

SUMMARY: Three cases of molluscum contagiosum (MC) approached our outpatient Department of Dermatology complaining of umbilicated, skin-colored, firm, painless papules over the neck and face. All of them were immune competent. The medical, social, and family history was insignificant. The lesions were, numerous and recurrent. However, MC in healthy people is a self-limiting disease, but it will take about 18 months to resolve by its own. Hence, the treatment becomes necessary to accelerate the healing process, preventing its spread and for cosmetic reasons. Most of the contemporary treatment methods such as cryotherapy, curettage, and topical application of caustic agents are effective but produce local side-effects such as erythema, tenderness, itching, burning sensation, and pain. The present study reports the efficacy of external application of Pratisaraṇīya Kṇāra (the type of Alkali used for smearing over the affected area) and Bilvādi Agada tablet orally in three cases, which yielded encouraging results. PMID:25161331

Anaerobic degradation of renewable biomass for production of methane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rajoka, M.I.; Tabassum, R.; Malik, K.A.

1996-12-31

Anaerobic degradation of renewable biomass namely kallar grass (KG) (Leptochloafusca L. Kunth), Atriplex sp, wheat straw, cotton stalk, cotton lint and molasses was carried out at 37{degrees}C in a 15 litre fermentor, using laboratory enriched co-culture of fermentative, acetogenic and methanogenic organisms. Maximum reduction of volatile solids (VS) was from causticized KG, and cotton lint, followed by causticized wheat straw and Atriplex sp. followed by causticized wheat straw and Atriplex sp. Maximum production of methane was obtained from NaOH-pretreated KG with a process product yield (Y{sub p/s}) of 0.9 m{sup 3}/kg VS with a volumetric productivity (Q{sub p}) of 4.24more » L/day after 19 days of fermentation. Maximum methane content in the gas mixture was 96% with average of 78.6{+-}21.6. The Y{sub p/s} in 1000 litre digestor was 0.7 m{sup 3}/kg VS from a 3% suspension of uncaustisized kallar grass.« less

Effect of magnetic starch on the clarification of hematite tailings wastewater

NASA Astrophysics Data System (ADS)

Yue, Tao; Wu, Xiqing

2018-02-01

The magnetic starch solution, synthesized by mixing the caustic starch, the Fe2+ solution (in some cases containing the Zn2+, Cu2+, Mn2+ or Mg2+ ions) and H2O2 solution, was used as the flocculant to investigate its clarification effect on hematite tailings wastewater. Based on the clarification tests and adsorption analysis it was demonstrated that the magnetic starch produced better clarification effect than the caustic starch, and the adsorption of magnetic starch onto hematite tailings particles was also stronger than the caustic starch. AFM found that the magnetic interaction between magnetic seeds and hematite is characteristic of long range force and greatly strengthens the adsorption of magnetic seeds onto fine hematite for agglomeration. FTIR indicates the starch adsorbed onto the surfaces of hematite and magnetic seeds, thus acting as the bridging between hematite particles and magnetic seeds, resulting in an intensified coverage of the starch onto hematite and positive action in the clarification.

Microbial Fuel Cell-driven caustic potash production from wastewater for carbon sequestration.

PubMed

Gajda, Iwona; Greenman, John; Melhuish, Chris; Santoro, Carlo; Ieropoulos, Ioannis

2016-09-01

This work reports on the novel formation of caustic potash (KOH) directly on the MFC cathode locking carbon dioxide into potassium bicarbonate salt (kalicinite) while producing, instead of consuming electrical power. Using potassium-rich wastewater as a fuel for microorganisms to generate electricity in the anode chamber, has resulted in the formation of caustic catholyte directly on the surface of the cathode electrode. Analysis of this liquid has shown to be highly alkaline (pH>13) and act as a CO2 sorbent. It has been later mineralised to kalicinite thus locking carbon dioxide into potassium bicarbonate salt. This work demonstrates an electricity generation method as a simple, cost-effective and environmentally friendly route towards CO2 sequestration that perhaps leads to a carbon negative economy. Moreover, it shows a potential application for both electricity production and nutrient recovery in the form of minerals from nutrient-rich wastewater streams such as urine for use as fertiliser in the future. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Sodium to sodium carbonate conversion process

DOEpatents

Herrmann, S.D.

1997-10-14

A method is described for converting radioactive alkali metal into a low level disposable solid waste material. The radioactive alkali metal is atomized and introduced into an aqueous caustic solution having caustic present in the range of from about 20 wt % to about 70 wt % to convert the radioactive alkali metal to a radioactive alkali metal hydroxide. The aqueous caustic containing radioactive alkali metal hydroxide and CO{sub 2} are introduced into a thin film evaporator with the CO{sub 2} present in an amount greater than required to convert the alkali metal hydroxide to a radioactive alkali metal carbonate, and thereafter the radioactive alkali metal carbonate is separated from the thin film evaporator as a dry powder. Hydroxide solutions containing toxic metal hydroxide including one or more metal ions of Sb, As, Ba, Be, Cd, Cr, Pb, Hg, Ni, Se, Ag and Tl can be converted into a low level non-hazardous waste using the thin film evaporator of the invention. 3 figs.

Highly crystalline films of PCPDTBT with branched side chains by solvent vapor crystallization: influence on opto-electronic properties.

PubMed

Fischer, Florian S U; Trefz, Daniel; Back, Justus; Kayunkid, Navaphun; Tornow, Benjamin; Albrecht, Steve; Yager, Kevin G; Singh, Gurpreet; Karim, Alamgir; Neher, Dieter; Brinkmann, Martin; Ludwigs, Sabine

2015-02-18

PCPDTBT, a marginally crystallizable polymer, is crystallized into a new crystal structure using solvent-vapor annealing. Highly ordered areas with three different polymer-chain orientations are identified using TEM/ED, GIWAXS, and polarized Raman spectroscopy. The optical and structural properties differ significantly from films prepared by standard device preparation protocols. Bilayer solar cells, however, show similar performance. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

REDISTRIBUTOR FOR LIQUID-LIQUID EXTRACTION COLUMNS

DOEpatents

Bradley, J.G.

1957-10-29

An improved baffle plate construction to intimately mix immiscible liquid solvents for solvent extraction processes in a liquid-liquid pulse column is described. To prevent the light and heavy liquids from forming separate continuous homogeneous vertical channels through sections of the column, a baffle having radially placed rectangular louvers with deflection plates opening upon alternate sides of the baffle is placed in the column, normal to the axis. This improvement substantially completely reduces strippiig losses due to poor mixing.

A hierarchy of functionally important relaxations within myoglobin based on solvent effects, mutations and kinetic model.

PubMed

Dantsker, David; Samuni, Uri; Friedman, Joel M; Agmon, Noam

2005-06-01

Geminate CO rebinding in myoglobin is studied for two viscous solvents, trehalose and sol-gel (bathed in 100% glycerol) at several temperatures. Mutations in key distal hemepocket residues are used to eliminate or enhance specific relaxation modes. The time-resolved data are analyzed with a modified Agmon-Hopfield model which is capable of providing excellent fits in cases where a single relaxation mode is dominant. Using this approach, we determine the relaxation rate constants of specific functionally important modes, obtaining also their Arrhenius activation energies. We find a hierarchy of distal pocket modes controlling the rebinding kinetics. The "heme access mode" (HAM) is responsible for the major slow-down in rebinding. It is a solvent-coupled cooperative mode which restricts ligand return from the xenon cavities. Bulky side-chains, like those His64 and Trp29 (in the L29W mutant), operate like overdamped pendulums which move over and block the binding site. They may be either unslaved (His64) or moderately slaved (Trp29) to the solvent. Small side-chain relaxations, most notably of leucines, are revealed in some mutants (V68L, V68A). They are conjectured to facilitate inter-cavity ligand motion. When all relaxations are arrested (H64L in trehalose), we observe pure inhomogeneous kinetics with no temperature dependence, suggesting that proximal relaxation is not a factor on the investigated timescale.

Relativistic Effects and Polarization in Three High-Energy Pulsar Models

NASA Technical Reports Server (NTRS)

Dyks, J.; Harding, Alice K.; Rudak, B.

2004-01-01

We present the influence of the special relativistic effects of aberration and light travel time delay on pulsar high-energy lightcurves and polarization characteristics predicted by three models: the two-pole caustic model, the outer gap model, and the polar cap model. Position angle curves and degree of polarization are calculated for the models and compared with the optical data on the Crab pulsar. The relative positions of peaks in gamma-ray and radio lightcurves are discussed in detail for the models. We find that the two-pole caustic model can reproduce qualitatively the optical polarization characteristics of the Crab pulsar - fast swings of the position angle and minima in polarization degree associated with both peaks. The anticorrelation between the observed flux and the polarization degree (observed in the optical band also for B0656+14) naturally results from the caustic nature of the peaks which are produced in the model due to the superposition of radiation from many different altitudes, ie. polarized at different angles. The two-pole caustic model also provides an acceptable interpretation of the main features in the Crab's radio profile. Neither the outer gap model nor the polar cap model are able to reproduce the optical polarization data on the Crab. Although the outer gap model is very successful in reproducing the relative positions of gamma-ray and radio peaks in pulse profiles, it can reproduce the high-energy lightcurves only when photon emission from regions very close to the light cylinder is included.

Computed Tomography Evaluation of Esophagogastric Necrosis After Caustic Ingestion.

PubMed

Chirica, Mircea; Resche-Rigon, Matthieu; Zagdanski, Anne Marie; Bruzzi, Matthieu; Bouda, Damien; Roland, Eric; Sabatier, François; Bouhidel, Fatiha; Bonnet, Francine; Munoz-Bongrand, Nicolas; Marc Gornet, Jean; Sarfati, Emile; Cattan, Pierre

2016-07-01

Endoscopy is the standard of care for emergency patient evaluation after caustic ingestion. However, the inaccuracy of endoscopy in determining the depth of intramural necrosis may lead to inappropriate decision-making with devastating consequences. Our aim was to evaluate the use of computed tomography (CT) for the emergency diagnostic workup of patients with caustic injuries. In a prospective study, we used a combined endoscopy-CT decision-making algorithm. The primary outcome was pathology-confirmed digestive necrosis. The respective utility of CT and endoscopy in the decision-making process were compared. Transmural endoscopic necrosis was defined as grade 3b injuries; signs of transmural CT necrosis included absence of postcontrast gastric/ esophageal-wall enhancement, esophageal-wall blurring, and periesophageal-fat blurring. We included 120 patients (59 men, median age 44 years). Emergency surgery was performed in 24 patients (20%) and digestive resection was completed in 16. Three patients (3%) died and 28 patients (23%) experienced complications. Pathology revealed transmural necrosis in 9/11 esophagectomy and 16/16 gastrectomy specimens. Severe oropharyngeal injuries (P = 0.015), increased levels of blood lactate (P = 0.007), alanine aminotransferase (P = 0.027), bilirubin (P = 0.005), and low platelet counts (P > 0.0001) were predictive of digestive necrosis. Decision-making relying on CT alone or on a combined CT-endoscopy algorithm was similar and would have spared 19 unnecessary esophagectomies and 16 explorative laparotomies compared with an endoscopy-alone algorithm. Endoscopy did never rectify a wrong CT decision. Emergency decision-making after caustic injuries can rely on CT alone.

Biometal binding-site mimicry with modular, hetero-bifunctionally modified architecture encompassing a Trp/His motif: insights into spatiotemporal noncovalent interactions from a comparative spectroscopic study.

PubMed

Yang, Chi Ming

2011-03-28

Metal-site Trp/His interactions are crucial to diverse metalloprotein functions. This paper presents a study using metal-motif mimicry to capture and dissect the static and transient components of physicochemical properties underlying the Trp/His aromatic side-chain noncovalent interactions across the first- and second-coordination spheres of biometal ions. Modular biomimetic constructs, EDTA-(L-Trp, L-His) or EWH and DTPA-(L-Trp, L-His) or DWH, featuring a function-significant Trp/His pair, enabled extracting the putative hydrophobic/hydrophilic aromatic interactions surrounding metal centers. Fluorescence, circular dichroism (CD) spectroscopic titrations and ESI mass spectrometry demonstrated that both the constructs stoichiometrically bind to Ca(2+), Co(2+), Cu(2+), Ni(2+), Mn(2+), Zn(2+), Cd(2+), and Fe(2+), and such binding was strongly coupled to stereospecific side-chain structure reorientations of the Trp indole and His imidazole rings. A mechanistic dichotomy corresponding to the participation of the indole unit in the binding event was revealed by a scaffold-platform correlation of steady-state fluorescence-response landscape, illuminating that secondary-coordination-sphere ligand cation-π interactions were immediately followed by subsequent transient physicochemical processes including through-space energy transfer, charge transfer and/or electron transfer, depending on the type of metals. The fluorescence quenching of Trp side chain by 3d metal ions can be ascribed to through-space d-π interactions. While the fluorescence titration was capable of illuminating a two-component energetic model, clean isosbestic/isodichroic points in the CD titration spectra indicated that the metallo-constructs, such as Cu(2+)-EWH complex, fold thermodynamically by means of a two-state equilibrium. Further, the metal-ion dependence of Trp conformational variation in the modular architecture of metal-bound scaffolds was evidenced unambiguously by the CD spectra and supported by MMFF calculations; both were capable of distinguishing between the coordination geometry and the preference for metal binding mode. The study thus helps understand how aromatic rings around metal-sites have unique capabilities through the control of the spatiotemporal distribution of noncovalent interaction elements to achieve diverse chemical functionality.

Seismic structures in the inner and outer core constrained by the PKP observations near the caustic distance range

NASA Astrophysics Data System (ADS)

Yu, W.; Wen, L.; Niu, F.

2002-05-01

We have extensively collected PKP waveforms around the PKP caustic distance range (141o - 147o) recorded in several dense regional arrays and the Global Seismic Network covering from 1990 to 2000. PKP observations at this distance range (141o - 147o) are usually purposely avoided in travel time analyses, because of the interference of various PKP branches. The observations there, however, will be extremely useful for constraining the seismic structures at both the top of the inner core and the bottom of the outer core. Moreover, because PKIKP phases sample a depth range of 100 km - 170 km below the inner-core boundary at this distant range, their observations fill the sampling depth gap between the PKiKP-PKIKP observations at the smaller distances and the PKPbc-PKIKP phases at the larger distances. Before the PKP caustics (141o - 145o), the diffracted PKP phases near the B caustics (PKPBdiff) and PKiKP phases are discernible in the long-period seismograms, and their differential travel times and waveforms could be used to constrain seismic structures at the bottom of the outer core and/or at the base of the mantle. The observed long-period PKiKP-PKPBdiff waveforms exhibit a hemispheric difference between those sampling the "eastern" and "western" hemispheres, with those sampling the "western" hemisphere showing larger time separations between the two phases. These observations can be explained by models with P velocity gradients of 0.0806 (km/s)/ 200 km for the "western" hemisphere and 0.114 (km/s)/200 km for the "eastern" hemisphere at the bottom of the outer core. Alternatively, these observations can also be explained by models with different velocity structures at the bottom 200 km of the mantle with P velocity variations in an order of 3 percent with respect to PREM. Broadband PKP observations after the PKP caustics (145o - 147o), on the other hand, provide high-quality constraints on the seismic structures at both the top of the inner core and the bottom of the outer core, as PKPbc phases can be used as excellent reference phases. We explore seismic models in both the bottom of the outer core and the top of the inner core, which can consistently explain the seismic observations at the caustic distance range (141o - 147o) and the PKiKP-PKIKP observations at the closer distances (Niu and Wen, Nature, 410, 1081-1084, 2001, Wen and Niu, JGR, submitted).

Cryochemistry: freezing effect on peptide coupling in different organic solutions.

PubMed

Vajda, T; Szókán, G; Hollósi, M

1998-06-01

The freezing effect on peptide coupling in organic solutions of different polarity has been investigated and compared with the results obtained in liquid phase. The model reaction of DCC-activated coupling of Boc-Ala-Phe-OH with H-Ala-OBu(t) has been carried out in dioxane, dimethylsulfoxide and formamide, as well as in mixtures (90%/10%, v/v) of dioxane with acetonitrile, dimethylformamide, dimethylsulfoxide and formamide. The reactions have been traced and evaluated by RP-HPLC analysis. Freezing the reaction mixture resulted in all cases in a significant suppression of the N-dipeptidylurea side-product formation together with a slight decrease of tripeptide epimerization. The coupling yields and the side effects depended on the solvent, with the dioxane and dioxane/acetonitrile mixture produced the best results. The role of freezing and solvent in the improved results is discussed.

Synthesis of diketopyrrolopyrrole-based polymers with polydimethylsiloxane side chains and their application in organic field-effect transistors

NASA Astrophysics Data System (ADS)

Ohnishi, Inori; Hashimoto, Kazuhito; Tajima, Keisuke

2018-03-01

Linear polydimethylsiloxane (PDMS) was investigated as a solubilizing group for π-conjugated polymers with the aim of combining high solubility in organic solvents with the molecular packing in solid films that is advantageous for charge transport. Diketopyrrolopyrrole-based copolymers with different contents and substitution patterns of the PDMS side chains were synthesized and evaluated for application in organic field-effect transistors. The PDMS side chains greatly increased the solubility of the polymers and led to shorter d-spacings of the π-stacking in the thin films compared with polymers containing conventional branched alkyl side chains.

Metal-doped organic foam and method of making same. [Patent application

DOEpatents

Rinde, J.A.

Organic foams having a low density and very small cell size and method for producing same in either a metal-loaded or unloaded (nonmetal loaded) form are described. Metal-doped foams are produced by soaking a polymer gel in an aqueous solution of desired metal salt, soaking the gel successively in a solvent series of decreasing polarity to remove water from the gel and replace it with a solvent of lower polarity with each successive solvent in the series being miscible with the solvents on each side and being saturated with the desired metal salt, and removing the last of the solvents from the gel to produce the desired metal-doped foam having desired density cell size, and metal loading. The unloaded or metal-doped foams can be utilized in a variety of applications requiring low density, small cell size foam. For example, rubidium-doped foam made in accordance with the invention has utility in special applications, such as in x-ray lasers.

Method of making metal-doped organic foam products

DOEpatents

Rinde, James A.

1981-01-01

Organic foams having a low density and very small cell size and method for roducing same in either a metal-loaded or unloaded (nonmetal loaded) form are described. Metal-doped foams are produced by soaking a polymer gel in an aqueous solution of desired metal salt, soaking the gel successively in a solvent series of decreasing polarity to remove water from the gel and replace it with a solvent of lower polarity with each successive solvent in the series being miscible with the solvents on each side and being saturated with the desired metal salt, and removing the last of the solvents from the gel to produce the desired metal-doped foam having desired density cell size, and metal loading. The unloaded or metal-doped foams can be utilized in a variety of applications requiring low density, small cell size foam. For example, rubidium-doped foam made in accordance with the invention has utility in special applications, such as in x-ray lasers.

Tooele Army Depot - South Area Suspected Release Units. RCRA Facility Investigation - Phase 2, for SWMUs 1, 25, and 27

DTIC Science & Technology

1995-11-01

Thickener (25% naphthenic acids) (25% oleic acid) Source: NUS 1987, Departments of the Army and Air Force 1963 2-8 TOO/TBL0025 07/21/94 11:45 am bpw S-60...Assessment does not state whether incineration occurred at SWMU 1 or elsewhere. The AC containers were decontaminated at SWMU 1 by rinsing with caustic ... caustic decontaminating agents that may have been applied during disposal. Decontaminating agents used include DANC (a mixture of sodium hydroxide and

Quantum Superalgebras at Roots of Unity and Topological Invariants of Three-manifolds

NASA Astrophysics Data System (ADS)

Blumen, Sacha C.

2006-01-01

The general method of Reshetikhin and Turaev is followed to develop topological invariants of closed, connected, orientable 3-manifolds from a new class of algebras called pseudo-modular Hopf algebras. Pseudo-modular Hopf algebras are a class of Z_2-graded ribbon Hopf algebras that generalise the concept of a modular Hopf algebra. The quantum superalgebra U_q(osp(1|2n)) over C is considered with q a primitive N^th root of unity for all integers N >= 3. For such a q, a certain left ideal I of U_q(osp(1|2n)) is also a two-sided Hopf ideal, and the quotient algebra U_q^(N)(osp(1|2n)) = U_q(osp(1|2n)) / I is a Z_2-graded ribbon Hopf algebra. For all n and all N >= 3, a finite collection of finite dimensional representations of U_q^(N)(osp(1|2n)) is defined. Each such representation of U_q^(N)(osp(1|2n)) is labelled by an integral dominant weight belonging to the truncated dominant Weyl chamber. Properties of these representations are considered: the quantum superdimension of each representation is calculated, each representation is shown to be self-dual, and more importantly, the decomposition of the tensor product of an arbitrary number of such representations is obtained for even N. It is proved that the quotient algebra U_q^(N)(osp(1|2n)), together with the set of finite dimensional representations discussed above, form a pseudo-modular Hopf algebra when N >= 6 is twice an odd number. Using this pseudo-modular Hopf algebra, we construct a topological invariant of 3-manifolds. This invariant is shown to be different to the topological invariants of 3-manifolds arising from quantum so(2n+1) at roots of unity.

A simple model of solvent-induced symmetry-breaking charge transfer in excited quadrupolar molecules

NASA Astrophysics Data System (ADS)

Ivanov, Anatoly I.; Dereka, Bogdan; Vauthey, Eric

2017-04-01

A simple model has been developed to describe the symmetry-breaking of the electronic distribution of AL-D-AR type molecules in the excited state, where D is an electron donor and AL and AR are identical acceptors. The origin of this process is usually associated with the interaction between the molecule and the solvent polarization that stabilizes an asymmetric and dipolar state, with a larger charge transfer on one side than on the other. An additional symmetry-breaking mechanism involving the direct Coulomb interaction of the charges on the acceptors is proposed. At the same time, the electronic coupling between the two degenerate states, which correspond to the transferred charge being localised either on AL or AR, favours a quadrupolar excited state with equal amount of charge-transfer on both sides. Because of these counteracting effects, symmetry breaking is only feasible when the electronic coupling remains below a threshold value, which depends on the solvation energy and the Coulomb repulsion energy between the charges located on AL and AR. This model allows reproducing the solvent polarity dependence of the symmetry-breaking reported recently using time-resolved infrared spectroscopy.

Time-Dependent Solid State Polymorphism of a Series of Donor-Acceptor Dyads

PubMed Central

Peebles, Cameron; Alvey, Paul M.; Lynch, Vincent; Iverson, Brent L.

2014-01-01

In order to exploit the use of favorable electrostatic interactions between aromatic units in directing the assembly of donor-acceptor (D-A) dyads, the present work examines the ability of conjugated aromatic D-A dyads with symmetric side chains to exhibit solid-state polymorphism as a function of time during the solid formation process. Four such dyads were synthesized and their packing in the solid-state from either slower (10-20 days) or faster (1-2 days) evaporation from solvent was investigated using single crystal X-ray analysis and powder X-ray diffraction. Two of the dyads exhibited tail-to-tail (A-A) packing upon slower evaporation from solvent and head-to-tail (D-A) packing upon faster evaporation from solvent. A combination of single crystal analysis and XRD patterns were used to create models wherein a packing model for the other two dyads is proposed. Our findings suggest that while side chain interactions in asymmetric aromatic dyads can play an important role in enforcing segregated D-A dyad assembly, slowly evaporating symmetrically substituted aromatic dyads allows for favorable electrostatic interactions between the aromatic moieties to facilitate the organization of the dyads in the solid-state. PMID:24678269

Conformational study of bovine lactoferricin in membrane-micking conditions by molecular dynamics simulation and circular dichroism.

PubMed

Daidone, Isabella; Magliano, Alessandro; Di Nola, Alfredo; Mignogna, Giuseppina; Clarkson, Matilda Manuela; Lizzi, Anna Rita; Oratore, Arduino; Mazza, Fernando

2011-04-01

Lactoferricins are potent antimicrobial peptides released by pepsin cleavage of Lactoferrins. Bovine Lactoferricin (LfcinB) has higher activity than the intact bovine Lactoferrin, and is the most active among the other Lactoferricins of human, murine and caprine origin. In the intact protein the fragment corresponding to LfcinB is in an helical conformation, while in water LfcinB adopts an amphipathic β-hairpin structure. However, whether any of these structural motifs is the antibacterial active conformation, i.e., the one interacting with bacterial membrane components, remains to be seen. Here we present Circular Dichroism (CD) spectra and Molecular Dynamics (MD) simulations indicating that in membrane-mimicking solvents the LfcinB adopts an amphipathic β-hairpin structure similar to that observed in water, but differing in the dynamic behavior of the side-chains of the two tryptophan residues. In the membrane-mimicking solvent these side-chains show a high propensity to point towards the hydrophobic environment, rather than being in the hydrophobic core as seen in water, while the backbone preserves the hairpin conformation as found in water. These results suggest that the tryptophans might act as anchors pulling the stable, solvent-invariant hairpin structure into the membrane.

Side-chain-side-chain interactions and stability of the helical state

NASA Astrophysics Data System (ADS)

Zangi, Ronen

2014-01-01

Understanding the driving forces that lead to the stability of the secondary motifs found in proteins, namely α-helix and β-sheet, is a major goal in structural biology. The thermodynamic stability of these repetitive units is a result of a delicate balance between many factors, which in addition to the peptide chain involves also the solvent. Despite the fact that the backbones of all amino acids are the same (except of that of proline), there are large differences in the propensity of the different amino acids to promote the helical structure. In this paper, we investigate by explicit-solvent molecular dynamics simulations the role of the side chains (modeled as coarse-grained single sites) in stabilizing α helices in an aqueous solution. Our model systems include four (six-mer-nine-mer) peptide lengths in which the magnitude of the effective attraction between the side chains is systematically increased. We find that these interactions between the side chains can induce (for the nine-mer almost completely) a transition from a coil to a helical state. This transition is found to be characterized by three states in which the intermediate state is a partially folded α-helical conformation. In the absence of any interactions between the side chains the free energy change for helix formation has a small positive value indicating that favorable contributions from the side chains are necessary to stabilize the helical conformation. Thus, the helix-coil transition is controlled by the effective potentials between the side-chain residues and the magnitude of the required attraction per residue, which is on the order of the thermal energy, reduces with the length of the peptide. Surprisingly, the plots of the population of the helical state (or the change in the free energy for helix formation) as a function of the total effective interactions between the side chains in the helical state for all peptide lengths fall on the same curve.

On the Observability of Individual Population III Stars and Their Stellar-mass Black Hole Accretion Disks through Cluster Caustic Transits

NASA Astrophysics Data System (ADS)

Windhorst, Rogier A.; Wyithe, Stuart; Alpaslan, Mehmet; Timmes, F. X.; Andrews, Stephen K.; Kim, Duho; Kelly, Patrick; Coe, Dan A.; Diego, Jose M.; Driver, Simon P.; Dijkstra, Mark

2018-06-01

We summarize panchromatic Extragalactic Background Light data to place upper limits on the integrated near-IR surface brightness (SB) that may come from Population III stars and possible accretion disks around their stellar-mass black holes (BHs) in the epoch of First Light, broadly taken from z=7-17.We outline the physical properties of zero-metallicity Population III stars from MESA stellar evolution models through helium depletion and of BH accretion disks at z>7. We assume that second-generation non-zero-metallicity stars can form at higher multiplicity, so that BH accretion disks may be fed by Roche-lobe overflow from lower-mass companions.We use these near-infrared SB constraints to calculate the number of caustic transits behind lensing clusters that the James Webb Space Telescope and the next-generation ground-based telescopes may observe for both Population III stars and their BH accretion disks. Typical caustic magnifications can be 10^4-10^5x, with rise times of hours and decline times of z~<1 year for cluster transverse velocities of v_T<~1000 km/s.Microlensing by intracluster-medium objects can modify transit magnifications but lengthen visibility times. Depending on BH masses, accretion-disk radii, and feeding efficiencies, stellar-mass BH accretion-disk caustic transits could outnumber those from Population III stars. To observe Population III caustic transits directly may require monitoring 3-30 lensing clusters to AB<29 mag over a decade (see Windhorst et al. 2018, ApJS, 234, 41; astro-ph/1801.03584).This work was supported by NASA JWST Interdisciplinary Scientist grants NAG5-12460, NX14AN10G, and 80NSSC18K0200, NASA Theoretical and Computational Astrophysics Networks grant NNX14AB53G, NSF Software Infrastructure for Sustained Innovation grant 1339600, NSF Physics Frontier Center JINA-CEE grant PHY-1430152, Australian Research Council projects AYA2015-64508-P, AYA2012-39475-C02-01, and Ministerio de Economia y Competitividad of Spain Consolider Project CSD2010-00064.

Non linear shock wave propagation in heterogeneous fluids: a numerical approach beyond the parabolic approximation with application to sonic boom.

NASA Astrophysics Data System (ADS)

Dagrau, Franck; Coulouvrat, François; Marchiano, Régis; Héron, Nicolas

2008-06-01

Dassault Aviation as a civil aircraft manufacturer is studying the feasibility of a supersonic business jet with the target of an "acceptable" sonic boom at the ground level, and in particular in case of focusing. A sonic boom computational process has been performed, that takes into account meteorological effects and aircraft manoeuvres. Turn manoeuvres and aircraft acceleration create zones of convergence of rays (caustics) which are the place of sound amplification. Therefore two elements have to be evaluated: firstly the geometrical position of the caustics, and secondly the noise level in the neighbourhood of the caustics. The modelling of the sonic boom propagation is based essentially on the assumptions of geometrical acoustics. Ray tracing is obtained according to Fermat's principle as paths that minimise the propagation time between the source (the aircraft) and the receiver. Wave amplitude and time waveform result from the solution of the inviscid Burgers' equation written along each individual ray. The "age variable" measuring the cumulative nonlinear effects is linked to the ray tube area. Caustics are located as the place where the ray tube area vanishes. Since geometrical acoustics does not take into account diffraction effects, it breaks down in the neighbourhood of caustics where it would predict unphysical infinite pressure amplitude. The aim of this study is to describe an original method for computing the focused noise level. The approach involves three main steps that can be summarised as follows. The propagation equation is solved by a forward marching procedure split into three successive steps: linear propagation in a homogeneous medium, linear perturbation due to the weak heterogeneity of the medium, and non-linear effects. The first step is solved using an "exact" angular spectrum algorithm. Parabolic approximation is applied only for the weak perturbation due to the heterogeneities. Finally, non linear effects are performed by solving the in-viscid Burgers' equation. As this one is valid for a plane wave, the direction of this last one is not prescribed a priori, but is computed in a self-adaptative way using an efficient numerical solver of the non-linear eikonal equation (Fast Marching Method).

Solvation thermodynamics of amino acid side chains on a short peptide backbone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hajari, Timir; Vegt, Nico F. A. van der, E-mail: vandervegt@csi.tu-darmstadt.de

The hydration process of side chain analogue molecules differs from that of the actual amino acid side chains in peptides and proteins owing to the effects of the peptide backbone on the aqueous solvent environment. A recent molecular simulation study has provided evidence that all nonpolar side chains, attached to a short peptide backbone, are considerably less hydrophobic than the free side chain analogue molecules. In contrast to this, the hydrophilicity of the polar side chains is hardly affected by the backbone. To analyze the origin of these observations, we here present a molecular simulation study on temperature dependent solvationmore » free energies of nonpolar and polar side chains attached to a short peptide backbone. The estimated solvation entropies and enthalpies of the various amino acid side chains are compared with existing side chain analogue data. The solvation entropies and enthalpies of the polar side chains are negative, but in absolute magnitude smaller compared with the corresponding analogue data. The observed differences are large; however, owing to a nearly perfect enthalpy-entropy compensation, the solvation free energies of polar side chains remain largely unaffected by the peptide backbone. We find that a similar compensation does not apply to the nonpolar side chains; while the backbone greatly reduces the unfavorable solvation entropies, the solvation enthalpies are either more favorable or only marginally affected. This results in a very small unfavorable free energy cost, or even free energy gain, of solvating the nonpolar side chains in strong contrast to solvation of small hydrophobic or nonpolar molecules in bulk water. The solvation free energies of nonpolar side chains have been furthermore decomposed into a repulsive cavity formation contribution and an attractive dispersion free energy contribution. We find that cavity formation next to the peptide backbone is entropically favored over formation of similar sized nonpolar side chain cavities in bulk water, in agreement with earlier work in the literature on analysis of cavity fluctuations at nonpolar molecular surfaces. The cavity and dispersion interaction contributions correlate quite well with the solvent accessible surface area of the nonpolar side chains attached to the backbone. This correlation however is weak for the overall solvation free energies owing to the fact that the cavity and dispersion free energy contributions are almost exactly cancelling each other.« less

Solvation thermodynamics of amino acid side chains on a short peptide backbone

NASA Astrophysics Data System (ADS)

Hajari, Timir; van der Vegt, Nico F. A.

2015-04-01

The hydration process of side chain analogue molecules differs from that of the actual amino acid side chains in peptides and proteins owing to the effects of the peptide backbone on the aqueous solvent environment. A recent molecular simulation study has provided evidence that all nonpolar side chains, attached to a short peptide backbone, are considerably less hydrophobic than the free side chain analogue molecules. In contrast to this, the hydrophilicity of the polar side chains is hardly affected by the backbone. To analyze the origin of these observations, we here present a molecular simulation study on temperature dependent solvation free energies of nonpolar and polar side chains attached to a short peptide backbone. The estimated solvation entropies and enthalpies of the various amino acid side chains are compared with existing side chain analogue data. The solvation entropies and enthalpies of the polar side chains are negative, but in absolute magnitude smaller compared with the corresponding analogue data. The observed differences are large; however, owing to a nearly perfect enthalpy-entropy compensation, the solvation free energies of polar side chains remain largely unaffected by the peptide backbone. We find that a similar compensation does not apply to the nonpolar side chains; while the backbone greatly reduces the unfavorable solvation entropies, the solvation enthalpies are either more favorable or only marginally affected. This results in a very small unfavorable free energy cost, or even free energy gain, of solvating the nonpolar side chains in strong contrast to solvation of small hydrophobic or nonpolar molecules in bulk water. The solvation free energies of nonpolar side chains have been furthermore decomposed into a repulsive cavity formation contribution and an attractive dispersion free energy contribution. We find that cavity formation next to the peptide backbone is entropically favored over formation of similar sized nonpolar side chain cavities in bulk water, in agreement with earlier work in the literature on analysis of cavity fluctuations at nonpolar molecular surfaces. The cavity and dispersion interaction contributions correlate quite well with the solvent accessible surface area of the nonpolar side chains attached to the backbone. This correlation however is weak for the overall solvation free energies owing to the fact that the cavity and dispersion free energy contributions are almost exactly cancelling each other.

Modular Systems Of Fixation And Position Jigs In The Production Process For Products And Systems

NASA Astrophysics Data System (ADS)

Babík, Ondrej; Šajgalík, Michal; Zaušková, Lucia; Czán, Andrej

2015-12-01

The project deals with design and implementation of adjustment onto mounting tables in the automotive industry. Manual control system of the jigs is replaced by a pneumatic system. Advantages of the pneumatic system are eliminating service side-time, improving work flow and increasing safety and ergonomics at work. Thanks to higher effectivity of the work process, manpower can be used in other work positions.

Evaluation Transportability Testing of the Joint Modular Intermodal Platform (JMIP) Unit #4, TP-94-01, Transportability Testing Procedures

DTIC Science & Technology

2007-07-01

447 3893 VSN: NL1FR5 MFG Serial #: T-018447EFJM Weight: 19,340 lbs 3-1 5. Semitrailer, flatbed , breakbulk/container transporter, 22.5 ton Model...CHAFTING PIECE, 118" X 6" X 40" PLYWOOD, (I REaD). LAMINATE TO BEARING PIECE W16-6d NAILS EVENLY SPACED. SIDE STRAPPING BOARD ASSEMBLY (2 REOD) (I

Forestry Training Manual for Africa Region U.S. Peace Corps. Training for Development. Peace Corps Information Collection & Exchange Training Manual No. T-14.

ERIC Educational Resources Information Center

Mahaffey, George; And Others

This manual is a state-side forestry teaching guide, complete with exercises, for the training of prospective Peace Corps volunteers who will serve in various African countries. The modular format lends itself to both single-country and multicountry forestry training. The first part of the guide contains instructions to the trainer on conducting…

Switching CAR T cells on and off: a novel modular platform for retargeting of T cells to AML blasts

PubMed Central

Cartellieri, M; Feldmann, A; Koristka, S; Arndt, C; Loff, S; Ehninger, A; von Bonin, M; Bejestani, E P; Ehninger, G; Bachmann, M P

2016-01-01

The adoptive transfer of CD19-specific chimeric antigen receptor engineered T cells (CAR T cells) resulted in encouraging clinical trials in indolent B-cell malignancies. However, they also show the limitations of this fascinating technology: CAR T cells can lead to even life-threatening off-tumor, on-target side effects if CAR T cells crossreact with healthy tissues. Here, we describe a novel modular universal CAR platform technology termed UniCAR that reduces the risk of on-target side effects by a rapid and reversible control of CAR T-cell reactivity. The UniCAR system consists of two components: (1) a CAR for an inert manipulation of T cells and (2) specific targeting modules (TMs) for redirecting UniCAR T cells in an individualized time- and target-dependent manner. UniCAR T cells can be armed against different tumor targets simply by replacement of the respective TM for (1) targeting more than one antigen simultaneously or subsequently to enhance efficacy and (2) reducing the risk for development of antigen-loss tumor variants under treatment. Here we provide ‘proof of concept' for retargeting of UniCAR T cells to CD33- and/or CD123-positive acute myeloid leukemia blasts in vitro and in vivo. PMID:27518241

Analysis of a modular generator for high-voltage, high-frequency pulsed applications, using low voltage semiconductors (< 1 kV) and series connected step-up (1:10) transformers.

PubMed

Redondo, L M; Fernando Silva, J; Margato, E

2007-03-01

This article discusses the operation of a modular generator topology, which has been developed for high-frequency (kHz), high-voltage (kV) pulsed applications. The proposed generator uses individual modules, each one consisting of a pulse circuit based on a modified forward converter, which takes advantage of the required low duty cycle to operate with a low voltage clamp reset circuit for the step-up transformer. This reduces the maximum voltage on the semiconductor devices of both primary and secondary transformer sides. The secondary winding of each step-up transformer is series connected, delivering a fraction of the total voltage. Each individual pulsed module is supplied via an isolation transformer. The assembled modular laboratorial prototype, with three 5 kV modules, 800 V semiconductor switches, and 1:10 step-up transformers, has 80% efficiency, and is capable of delivering, into resistive loads, -15 kV1 A pulses with 5 micros width, 10 kHz repetition rate, with less than 1 micros pulse rise time. Experimental results for resistive loads are presented and discussed.

Solid oxide fuel cell generator with removable modular fuel cell stack configurations

DOEpatents

Gillett, J.E.; Dederer, J.T.; Zafred, P.R.; Collie, J.C.

1998-04-21

A high temperature solid oxide fuel cell generator produces electrical power from oxidation of hydrocarbon fuel gases such as natural gas, or conditioned fuel gases, such as carbon monoxide or hydrogen, with oxidant gases, such as air or oxygen. This electrochemical reaction occurs in a plurality of electrically connected solid oxide fuel cells bundled and arrayed in a unitary modular fuel cell stack disposed in a compartment in the generator container. The use of a unitary modular fuel cell stack in a generator is similar in concept to that of a removable battery. The fuel cell stack is provided in a pre-assembled self-supporting configuration where the fuel cells are mounted to a common structural base having surrounding side walls defining a chamber. Associated generator equipment may also be mounted to the fuel cell stack configuration to be integral therewith, such as a fuel and oxidant supply and distribution systems, fuel reformation systems, fuel cell support systems, combustion, exhaust and spent fuel recirculation systems, and the like. The pre-assembled self-supporting fuel cell stack arrangement allows for easier assembly, installation, maintenance, better structural support and longer life of the fuel cells contained in the fuel cell stack. 8 figs.

Solid oxide fuel cell generator with removable modular fuel cell stack configurations

DOEpatents

Gillett, James E.; Dederer, Jeffrey T.; Zafred, Paolo R.; Collie, Jeffrey C.

1998-01-01

A high temperature solid oxide fuel cell generator produces electrical power from oxidation of hydrocarbon fuel gases such as natural gas, or conditioned fuel gases, such as carbon monoxide or hydrogen, with oxidant gases, such as air or oxygen. This electrochemical reaction occurs in a plurality of electrically connected solid oxide fuel cells bundled and arrayed in a unitary modular fuel cell stack disposed in a compartment in the generator container. The use of a unitary modular fuel cell stack in a generator is similar in concept to that of a removable battery. The fuel cell stack is provided in a pre-assembled self-supporting configuration where the fuel cells are mounted to a common structural base having surrounding side walls defining a chamber. Associated generator equipment may also be mounted to the fuel cell stack configuration to be integral therewith, such as a fuel and oxidant supply and distribution systems, fuel reformation systems, fuel cell support systems, combustion, exhaust and spent fuel recirculation systems, and the like. The pre-assembled self-supporting fuel cell stack arrangement allows for easier assembly, installation, maintenance, better structural support and longer life of the fuel cells contained in the fuel cell stack.

TOXIC EXPOSURES IN CHILDREN INVOLVING LEGALLY AND ILLEGALLY COMMERCIALIZED HOUSEHOLD SANITIZERS

PubMed Central

Campos, Alessandra Marcuz de Souza; Bucaretchi, Fábio; Fernandes, Luciane Cristina Rodrigues; Fernandes, Carla Borrasca; de Capitani, Eduardo Mello; Beck, Ana Raquel Medeiros

2017-01-01

ABSTRACT Objectives: To analyze and to compare clinical repercussions of accidents involving legally and illegally commercialized household sanitizers in children under 7 years of age. Methods: A descriptive cross-sectional design was used to collect data from electronic database of a regional Poison Control Center during one year. Data were analyzed by means of descriptive non-parametric statistics and association tests. Results: The sample had 737 reported cases. Most of the accidents occurred with children under 3 years of age (median: 1 year of age; interquartile interval: 1-3 years of age), at home (92.9%), by ingestion (97.2%). Products involved were cleaning products with low toxicity and no caustic effects (38.9%); caustics (24.1%); hydrocarbons (19.3%); pesticides/rodenticides (16.6%), and other products (1.1%). Seventy accidents were due to exposures to illegal products, mainly caustics (n=47) and rodenticides (n=15). Among the 337 children presenting post-exposure clinical manifestations, the most frequent were vomiting (n=125), oral burns (n=74), cough (n=35), drooling (n=26), and abdominal pain (n=25). Clinical manifestations were significantly more frequent after illegal products exposure (55/70 versus 282/667, p<0.01). Nineteen children had to be hospitalized (caustics, n=17; illegal products, n=12; median time of hospitalization: 2 days), 22 were submitted to esophagogastroduodenoscopy (sodium hydroxide, n=14; illegal products, n=14); and 12 cases had endoscopic alterations (severe in 2). No deaths occurred. Conclusion: Toxic exposures owing to illegal household sanitizer products are associated with greater morbidity when compared with legal ones. PMID:28977311

Patients Admitted to Three Spanish Intensive Care Units for Poisoning: Type of Poisoning, Mortality, and Functioning of Prognostic Scores Commonly Used

PubMed Central

Banderas-Bravo, María Esther; Arias-Verdú, Maria Dolores; Macías-Guarasa, Ines; Castillo-Lorente, Encarnación; Pérez-Costillas, Lucia; Gutierrez-Rodriguez, Raquel; Quesada-García, Guillermo; Rivera-Fernández, Ricardo

2017-01-01

Objectives. To evaluate the gravity and mortality of those patients admitted to the intensive care unit for poisoning. Also, the applicability and predicted capacity of prognostic scales most frequently used in ICU must be evaluated. Methods. Multicentre study between 2008 and 2013 on all patients admitted for poisoning. Results. The results are from 119 patients. The causes of poisoning were medication, 92 patients (77.3%), caustics, 11 (9.2%), and alcohol, 20 (16,8%). 78.3% attempted suicides. Mean age was 44.42 ± 13.85 years. 72.5% had a Glasgow Coma Scale (GCS) ≤8 points. The ICU mortality was 5.9% and the hospital mortality was 6.7%. The mortality from caustic poisoning was 54.5%, and it was 1.9% for noncaustic poisoning (p < 0.001). After adjusting for SAPS-3 (OR: 1.19 (1.02–1.39)) the mortality of patients who had ingested caustics was far higher than the rest (OR: 560.34 (11.64–26973.83)). There was considerable discrepancy between mortality predicted by SAPS-3 (26.8%) and observed (6.7%) (Hosmer-Lemeshow test: H = 35.10; p < 0.001). The APACHE-II (7,57%) and APACHE-III (8,15%) were no discrepancies. Conclusions. Admission to ICU for poisoning is rare in our country. Medication is the most frequent cause, but mortality of caustic poisoning is higher. APACHE-II and APACHE-III provide adequate predictions about mortality, while SAPS-3 tends to overestimate. PMID:28459061

AMDTreat 5.0+ with PHREEQC titration module to compute caustic chemical quantity, effluent quality, and sludge volume

USGS Publications Warehouse

Cravotta, Charles A.; Means, Brent P; Arthur, Willam; McKenzie, Robert M; Parkhurst, David L.

2015-01-01

Alkaline chemicals are commonly added to discharges from coal mines to increase pH and decrease concentrations of acidity and dissolved aluminum, iron, manganese, and associated metals. The annual cost of chemical treatment depends on the type and quantities of chemicals added and sludge produced. The AMDTreat computer program, initially developed in 2003, is widely used to compute such costs on the basis of the user-specified flow rate and water quality data for the untreated AMD. Although AMDTreat can use results of empirical titration of net-acidic or net-alkaline effluent with caustic chemicals to accurately estimate costs for treatment, such empirical data are rarely available. A titration simulation module using the geochemical program PHREEQC has been incorporated with AMDTreat 5.0+ to improve the capability of AMDTreat to estimate: (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the chemical composition of the treated effluent, and (3) the volume of sludge produced by the treatment. The simulated titration results for selected caustic chemicals (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) without aeration or with pre-aeration can be compared with or used in place of empirical titration data to estimate chemical quantities, treated effluent composition, sludge volume (precipitated metals plus unreacted chemical), and associated treatment costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module with the new AMDTreat 5.0+ computer program available at http://www.amd.osmre.gov/.

Regeneration of iron-based adsorptive media used for removing arsenic from groundwater.

PubMed

Chen, Abraham S C; Sorg, Thomas J; Wang, Lili

2015-06-15

Adsorptive media technology is regarded as a simple, low cost method of removing arsenic from drinking water particularly for small systems. Currently, when the effluent of a treatment system reaches the USEPA maximum contaminant level (MCL) of 10 ug/L, the exhausted media is removed and replaced by new virgin media. Although the commonly used iron-based media products are reasonable in price, the replacement cost accounts for around 80% of the systems total operational costs. One option to media replacement is on-site regeneration and reuse of the exhausted media. To determine whether an iron based media can be successfully regenerated and reused, laboratory batch and column regeneration tests were conducted on six exhausted iron-based media products obtained from six full scale arsenic removal treatment systems. Batch tests conducted on three of the media products to evaluate the effectiveness of 1-6% caustic regenerant solutions found that arsenic desorption increased until around 4%. Using 4% caustic solutions, the columns tests on the six exhausted media products showed arsenic removals ranged from 25 to 90% with the best results obtained with the Severn Trent E33 media. Exposing the media to caustic (pH ≥ 13) and acid (pH ≤ 2) solutions found minimal media loss with the caustic solution, but significant media dissolution with a pH 2 acid solution. A six column pilot plant test at an Ohio test site with the lab regenerated media products found that the regenerated media could achieve arsenic removals somewhat similar to virgin media. Copyright © 2015 Elsevier Ltd. All rights reserved.

Inhibition of the acetoclastic methanogenic activity by phenol and alkyl phenols.

PubMed

Olguin-Lora, P; Puig-Grajales, L; Razo-Flores, E

2003-08-01

Chemical and petrochemical industries are important sources of aromatic pollutants. Petrochemical processes like caustic washing of middle distillates produce the spent caustic liquors highly concentrated in phenol and alkyl phenols. The anaerobic technology is considered a feasible strategy for petrochemical wastewater pre-treatment although high concentrations of phenol could limit its efficiency. The goal of this work was to determine the toxicity of both selected alkyl phenols and a synthetic "spent-caustic phenols mixture" on the acetoclastic Specific Methanogenic Activity (SMA) of unadapted and phenol-adapted granular sludge. Alkyl phenols were responsible for 50% (IC50) and 100% (IC100) inhibition of the SMA at concentrations ranging from 1.6 to 5.0 mM and from 4.1 to 27.5 mM, respectively, for un-adapted granular sludge. In the case of phenol-adapted granular sludge, the inhibitory concentrations ranged from 1.7 to 14.9 mM and from 4.0 to 83.0 for IC50 and IC100, respectively, highlighting the impact of sludge acclimation. The inhibition produced by 2-ethylphenol was more acute compared to phenol and was not reduced by the phenol acclimation process. The IC50 and IC100 values obtained for the synthetic "spent-caustic phenols mixture" were 9.5 mM and 88.4 mM, respectively. The inhibitory concentrations of phenol compounds were closely correlated with compound apolarity (log P), indicating that the lipophilic character of the tested compounds was responsible for their methanogenic toxicity. An inhibition model is confirmed to estimate the IC50 and IC100.

Energy conversion performance of black liquor gasification to hydrogen production using direct causticization with CO(2) capture.

PubMed

Naqvi, M; Yan, J; Dahlquist, E

2012-04-01

This paper estimates potential hydrogen production via dry black liquor gasification system with direct causticization integrated with a reference pulp mill. The advantage of using direct causticization is elimination of energy intensive lime kiln. Pressure swing adsorption is integrated in the carbon capture process for hydrogen upgrading. The energy conversion performance of the integrated system is compared with other bio-fuel alternatives and evaluated based on system performance indicators. The results indicated a significant hydrogen production potential (about 141MW) with an energy ratio of about 0.74 from the reference black liquor capacity (about 243.5MW) and extra biomass import (about 50MW) to compensate total energy deficit. About 867,000tonnes of CO(2) abatement per year is estimated i.e. combining CO(2) capture and CO(2) offset from hydrogen replacing motor gasoline. The hydrogen production offers a substantial motor fuel replacement especially in regions with large pulp and paper industry e.g. about 63% of domestic gasoline replacement in Sweden. Copyright © 2012 Elsevier Ltd. All rights reserved.

Spent caustic oxidation using electro-generated Fenton's reagent in a batch reactor.

PubMed

Rodriguez, Nicolas; Hansen, Henrik K; Nunez, Patricio; Guzman, Jaime

2008-07-01

This work shows the results of four Electro-Fenton laboratory tests to reduce the chemical oxygen demand (COD) in spent caustic solutions. The treatment consisted of (i) a pH reduction followed by (ii) an Electro-Fenton process, which was analyzed in this work. The Fenton's reagent was produced in a specially designed reactor, where the waste stream flowed through a labyrinth made by ferrous plates. These plates acted as sacrificial anodes-releasing Fe(2 +) cations to the solution, where H(2)O(2) was also added. The Electro-Fenton process was analyzed varying the ferrous ion concentration ([Fe(+ 2)]), the spent caustic's initial temperature and the initial pH. Close to 95% removal of COD (from 8800 mg L(- 1)) was achieved at a pH of 4, a temperature of 40 degrees C and 100 mg L(- 1) of Fe(+ 2) (applying 1 A). Two models were considered to simulate the behavior of the reactor considering (i) axial dispersion and (ii) kinetic rate, respectively. The model that was based on kinetics, proved to be the slightly closest fit to the experimental values.

Investigation of transient forms of sulfur during biological treatment of spent caustic.

PubMed

Kalantari, Hamed; Nosrati, Mohsen; Shojaosadati, Seyed Abbas; Shavandi, Mahmoud

2018-06-01

In the present study, the production of various transient forms of sulfur during biological oxidation of sulfidic spent caustics under haloalkaline conditions in a stirred tank bioreactor is investigated. Also, the effects of abiotic aeration (chemical oxidation), dissolved oxygen (DO) concentration and sodium concentration on forms of sulfur during biological treatment are demonstrated. Thioalkalivibrio versutus strain was used for sulfide oxidation in spent caustic (SC). The aeration had an important effect on sulfide oxidation and its final products. At DO concentrations above 2 mg l -1 , majority of sulfide was oxidized to sulfate. Maximum sulfide removal efficiency (%R) and yield of sulfate production [Formula: see text] was obtained in Na + concentration ranging from 0.6 to 2 M. Abiotic aeration, which is the most important factor of production of thiosulfate, resulted in the formation of an undesired product-polysulfide. However, abiotic aeration can be used as a pretreatment to biological treatment. In the bioreactor the removal efficiency was obtained as 82.7% and various forms of sulfur such as polysulfide, biosulfur, thiosulfate and sulfate was observed during biological treatment of SC.

F-Area Acid/Caustic Basin groundwater monitoring report: Third quarter 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-12-01

During third quarter 1994, samples from the FAC monitoring wells at the F-Area Acid/Caustic Basin were collected and analyzed for herbicides/pesticides, indicator parameters, metals, nitrate, radionuclide indicators, volatile organic compounds, and other constituents. Piezometer FAC 5P and monitoring well FAC 6 were dry and could not be sampled. New monitoring wells FAC 9C, 10C, 11C, and 12C were sampled for the first time during third quarter. Analytical results that exceeded final Primary Drinking Water Standards (PDWS), other Savannah River Site (SRS) Flag 2 criteria, or the SRS turbidity standard of 50 NTU during the quarter were as follows: gross alphamore » exceeded the final PDWS and aluminum, iron, manganese, and total alpha-emitting radium exceeded the SRS Flag 2 criteria in one or more of the FAC wells. Turbidity exceeded the SRS standard in wells FAC 3 and 10C. Groundwater flow direction and rate in the water table beneath the F-Area Acid/Caustic Basin were similar to past quarters.« less

Improved synthesis of phosphatidylserine using bio-based solvents, limonene and p-cymene.

PubMed

Bi, Yan-Hong; Duan, Zhang-Qun; Du, Wen-Ying; Wang, Zhao-Yu

2015-01-01

The bio-based solvents limonene and p-cymene obtained from citrus waste were innovatively employed as the reaction media for enzymatic synthesis of phosphatidylserine. (R)-(+)-Limonene, which is available in large quantities from citrus waste, and its close derivative p-cymene, are promising green solvents. Herein, they were successfully employed as reaction media for enzyme-mediated transphosphatidylation of phosphatidylcholine with L-serine for phosphatidylserine synthesis for the first time. A 95 % yield of phosphatidylserine was achieved after 12 h and the side-reactions (which are the undesirable hydrolysis of phosphatidylcholine and phosphatidylserine) did not happen. This work presents an alternative strategy for preparing phosphatidylserine that possesses obvious advantages over the traditional processes in terms of high efficiency combined with environmental friendliness.

Hydration structure of the α-chymotrypsin substrate binding pocket: the impact of constrained geometry

NASA Astrophysics Data System (ADS)

Carey, Christina; Cheng, Yuen-Kit; Rossky, Peter J.

2000-08-01

The concave substrate binding pocket of α-chymotrypsin binds specifically hydrophobic side chains. In order to understand the hydration structure present in the absence of substrate, and elucidate the character of the solvent displaced on binding, molecular dynamics computer simulation of the solvent in a fully hydrated protein has been carried out and analyzed. The pocket is found to be characterized in terms of a mixed polar and apolar macromolecular surface. It is shown that the simulated solvent structure within it is spatially consistent with that seen via crystallography. The solvent structure is energetically characterized by large losses in hydrogen bonding among solvent molecules except at the mouth of the pocket where exposure to bulk-like solvent is possible. The loss in hydrogen bonding is attributed to the highly constrained geometry available to the solvent, preventing formation of a hydrogen bonding network, with only partial compensation by interactions with the macromolecular surface. The solvent displacement concomitant with substrate binding will therefore be associated with a large enthalpic driving force. This result is at the extreme of a continuum of variable cases of "hydrophobic" hydration, which differ most basically in surface curvature. These range from convex solute surfaces, inducing clathrate-like structures, with negligible hydrogen bond loss, to flat surfaces with significant interfacial loss, to the present concave case with hydrogen bonding losses exceeding 50%.

Pad ultrasonic batch dyeing of causticized lyocell fabric with reactive dyes.

PubMed

Babar, Aijaz Ahmed; Peerzada, Mazhar Hussain; Jhatial, Abdul Khalique; Bughio, Noor-Ul-Ain

2017-01-01

Conventionally, cellulosic fabric dyed with reactive dyes requires significant amount of salt. However, the dyeing of a solvent spun regenerated cellulosic fiber is a critical process. This paper presents the dyeing results of lyocell fabrics dyed with conventional pad batch (CPB) and pad ultrasonic batch (PUB) processes. The dyeing of lyocell fabrics was carried out with two commercial dyes namely Drimarine Blue CL-BR and Ramazol Blue RGB. Dyeing parameters including concentration of sodium hydroxide, sodium carbonate and dwell time were compared for the two processes. The outcomes show that PUB dyed samples offered reasonably higher color yield and dye fixation than CPB dyed samples. A remarkable reduction of 12h in batching time, 18ml/l in NaOH and 05g/l in Na 2 CO 3 quantity was observed for PUB processed samples producing similar results compared to CPB process, making PUB a more economical, productive and an environment friendly process. Color fastness examination witnessed identical results for both PUB and CPB methods. No significant change in surface morphology of PUB processed samples was observed through scanning electron microscope (SEM) analysis. Copyright © 2016 Elsevier B.V. All rights reserved.

Impaired colour vision in workers exposed to organic solvents: A systematic review.

PubMed

Betancur-Sánchez, A M; Vásquez-Trespalacios, E M; Sardi-Correa, C

2017-01-01

To evaluate recent evidence concerning the relationship between the exposure to organic solvents and the impairment of colour vision. A bibliographic search was conducted for scientific papers published in the last 15 years, in the LILACS, PubMed, Science Direct, EBSCO, and Cochrane databases that included observational studies assessing the relationship between impairment in colour vision and exposure to organic solvents. Eleven studies were selected that were performed on an economically active population and used the Lanthony D-15 desaturated test (D-15d), measured the exposure to organic solvents, and included unexposed controls. It was found that there is a statistically significant relationship between the exposure to organic solvents and the presence of an impairment in colour vision. The results support the hypothesis that exposure to organic solvents could induce acquired dyschromatopsia. The evaluation of colour vision with the D-15d test is simple and sensitive for diagnosis. More studies need to be conducted on this subject in order to better understand the relationship between impaired colour vision and more severe side effects caused by this exposure. Copyright © 2016 Sociedad Española de Oftalmología. Publicado por Elsevier España, S.L.U. All rights reserved.

Interactive Dynamic Volume Illumination with Refraction and Caustics.

PubMed

Magnus, Jens G; Bruckner, Stefan

2018-01-01

In recent years, significant progress has been made in developing high-quality interactive methods for realistic volume illumination. However, refraction - despite being an important aspect of light propagation in participating media - has so far only received little attention. In this paper, we present a novel approach for refractive volume illumination including caustics capable of interactive frame rates. By interleaving light and viewing ray propagation, our technique avoids memory-intensive storage of illumination information and does not require any precomputation. It is fully dynamic and all parameters such as light position and transfer function can be modified interactively without a performance penalty.

Acute colitis caused by caustic products.

PubMed

da Fonseca, J; Brito, M J; Freitas, J; Leal, C

1998-12-01

We report two cases of acute proctocolitis caused by rectal application of caustic products of domestic use. One 61-yr-old woman applied an ammonia solution enema; the other patient, a 63-yr-old woman, accidentally applied an enema containing lye. Both patients presented with intense anal pain, but the first patient also had abdominal pain with guarding, hematochezia, and leucocytosis. An acute proctocolitis was found at sigmoidoscopy in both patients. Only conservative and symptomatic measures were prescribed in both cases, and a clinical and endoscopic recovery was seen. In spite of persistent fibrosis in the lamina propria, no signs of stenosis were found.

Laboratory study of sonic booms and their scaling laws. [ballistic range simulation

NASA Technical Reports Server (NTRS)

Toong, T. Y.

1974-01-01

This program undertook to seek a basic understanding of non-linear effects associated with caustics, through laboratory simulation experiments of sonic booms in a ballistic range and a coordinated theoretical study of scaling laws. Two cases of superbooms or enhanced sonic booms at caustics have been studied. The first case, referred to as acceleration superbooms, is related to the enhanced sonic booms generated during the acceleration maneuvers of supersonic aircrafts. The second case, referred to as refraction superbooms, involves the superbooms that are generated as a result of atmospheric refraction. Important theoretical and experimental results are briefly reported.

Unifying the microscopic picture of His-containing turns: from gas phase model peptides to crystallized proteins.

PubMed

Sohn, Woon Yong; Habka, Sana; Gloaguen, Eric; Mons, Michel

2017-07-14

The presence in crystallized proteins of a local anchoring between the side chain of a His residue, located in the central position of a γ- or β-turn, and its local main chain environment, was assessed by the comparison of protein structures with relevant isolated model peptides. Gas phase laser spectroscopy, combined with relevant quantum chemistry methods, was used to characterize the γ- and β-turn structures in these model peptides. A conformer-selective NH stretch infrared study provided evidence for the formation in vacuo of two types of short-range H-bonded motifs, labelled ε-6 δ and δ- δ 7/π H , bridging the His side chain (in its gauche+ rotamer) to the neighbouring NH(i) and CO(i) sites of the backbone; each side chain-backbone motif was found to be specific of the tautomer (ε or δ) adopted by the His side chain in its neutral form. A close comparison between β- and γ-turns, selected from the Protein Data Bank, and the gas phase models demonstrated that a significant proportion of the gauche+ His rotamer distribution of proteins was well described by the corresponding gas phase H-bonded structures. This is consistent with the persistence of local 6 δ and δ 7/π H intramolecular interactions in proteins, emphasizing the relevance of gas phase data to secondary structures that are poorly accessible to solvents, e.g., in the case of a specific compact topology (Xxx-His β-turns). Deviations from the gas phase structures were also observed, mainly in His-Xxx β-turns, and assigned to solvent accessible turn structures. They were well accounted for by theoretical models of microhydrated turns, in which a few solvent molecules take over the gas phase motifs, constituting a water-mediated local anchoring of the His side chain to the backbone. Finally, the present gas phase benchmark models also pinpointed weaknesses in the protein structure determination by X-ray diffraction analysis; in particular, besides the lack of tautomer information, inaccuracies in the description of imidazole ring flip rotamerism were identified.

Matrix recrystallization for MALDI-MS imaging of maize lipids at high-spatial resolution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duenas, Maria Emilia; Carlucci, Laura; Lee, Young Jin

Matrix recrystallization is optimized and applied to improve lipid ion signals in maize embryos and leaves. A systematic study was performed varying solvent and incubation time. During this study, unexpected side reactions were found when methanol was used as a recrystallization solvent, resulting in the formation of a methyl ester of phosphatidic acid. Furthermore, using an optimum recrystallization condition with isopropanol, there is no apparent delocalization demonstrated with a transmission electron microscopy (TEM) pattern and maize leaf images obtained at 10 μm spatial resolution.

Matrix recrystallization for MALDI-MS imaging of maize lipids at high-spatial resolution

DOE PAGES

Duenas, Maria Emilia; Carlucci, Laura; Lee, Young Jin

2016-06-27

Matrix recrystallization is optimized and applied to improve lipid ion signals in maize embryos and leaves. A systematic study was performed varying solvent and incubation time. During this study, unexpected side reactions were found when methanol was used as a recrystallization solvent, resulting in the formation of a methyl ester of phosphatidic acid. Furthermore, using an optimum recrystallization condition with isopropanol, there is no apparent delocalization demonstrated with a transmission electron microscopy (TEM) pattern and maize leaf images obtained at 10 μm spatial resolution.

Matrix Recrystallization for MALDI-MS Imaging of Maize Lipids at High-Spatial Resolution

NASA Astrophysics Data System (ADS)

Dueñas, Maria Emilia; Carlucci, Laura; Lee, Young Jin

2016-09-01

Matrix recrystallization is optimized and applied to improve lipid ion signals in maize embryos and leaves. A systematic study was performed varying solvent and incubation time. During this study, unexpected side reactions were found when methanol was used as a recrystallization solvent, resulting in the formation of a methyl ester of phosphatidic acid. Using an optimum recrystallization condition with isopropanol, there is no apparent delocalization demonstrated with a transmission electron microscopy (TEM) pattern and maize leaf images obtained at 10 μm spatial resolution.

Studies on the Inhalation Toxicity of Dyes Present in Colored Smoke Munitions. Phase I Studies: Generation and Characterization of Dye Aerosol

DTIC Science & Technology

1984-02-01

DYE AEROSOL Rogene F. Henderson Y. S. Cheng J. S. Dutcher T. C. Marshall J. E. White 0)February 1 . 1984 Supported by SU. S. ARMY MEDICAL RESEARCH AND...from Report) 1 . SUPPLEMENTARY NOTES IS. KEY WORDS (Coattine on re tore* side I’ necessary teid iatfiy by biock nuqber) Solvent Yellow Dye Aerosols...Solvent Green Exposure Atmosphere 2-(2’-quinolyl )-1,3-indandione 1 -4-di-p-toluidinoanthraquinone 20. AmTlACT (Cowftfuem a reserve ft D rofmwe ,uy md

Matrix Recrystallization for MALDI-MS Imaging of Maize Lipids at High-Spatial Resolution.

PubMed

Dueñas, Maria Emilia; Carlucci, Laura; Lee, Young Jin

2016-09-01

Matrix recrystallization is optimized and applied to improve lipid ion signals in maize embryos and leaves. A systematic study was performed varying solvent and incubation time. During this study, unexpected side reactions were found when methanol was used as a recrystallization solvent, resulting in the formation of a methyl ester of phosphatidic acid. Using an optimum recrystallization condition with isopropanol, there is no apparent delocalization demonstrated with a transmission electron microscopy (TEM) pattern and maize leaf images obtained at 10 μm spatial resolution. Graphical Abstract ᅟ.

Modular electronics packaging system

NASA Technical Reports Server (NTRS)

Hunter, Don J. (Inventor)

2001-01-01

A modular electronics packaging system includes multiple packaging slices that are mounted horizontally to a base structure. The slices interlock to provide added structural support. Each packaging slice includes a rigid and thermally conductive housing having four side walls that together form a cavity to house an electronic circuit. The chamber is enclosed on one end by an end wall, or web, that isolates the electronic circuit from a circuit in an adjacent packaging slice. The web also provides a thermal path between the electronic circuit and the base structure. Each slice also includes a mounting bracket that connects the packaging slice to the base structure. Four guide pins protrude from the slice into four corresponding receptacles in an adjacent slice. A locking element, such as a set screw, protrudes into each receptacle and interlocks with the corresponding guide pin. A conduit is formed in the slice to allow electrical connection to the electronic circuit.

Cooperative Order-Disorder Transition of Carboxylated Schizophyllan in Water-Dimethylsulfoxide Mixtures.

PubMed

Yoshiba, Kazuto; Dobashi, Toshiaki; Ulset, Ann-Sissel T; Christensen, Bjørn E

2018-06-18

Carboxylated schizophyllan ("sclerox") is a chemically modified polysaccharide obtained by partial periodate oxidation and subsequent chlorite oxidation of schizophyllan, a water-soluble neutral polysaccharide having a β-1,3-linked glucan backbone and a β-1,6-linked d-glucose residue side chain at every third residue of the main chain. The triple helix of schizophyllan in water has a cooperative order-disorder transition associated with the side chains. The transition is strongly affected by the presence (mole fraction) of dimethylsulfoxide (DMSO). In the present study, the solvent effects on the order-disorder transition of sclerox with different degrees of carboxylation (DS) in water-DMSO mixtures were investigated with differential scanning calorimetry and optical rotation. The transition temperature ( T r ) and transition enthalpy (Δ H r ) strongly depended on the mole fraction of DMSO ( x D ). Data were further analyzed with the statistical theory for the linear cooperative transition, taking into account the solvent effect, where DMSO molecules are selectively associated with the unmodified side chains. The modified side chain does not contribute to the transition; hence, Δ H r decreases with increasing DS. The dependence of T r on the DMSO content becomes weaker than that for unmodified schizophyllan. The theoretical analyses indicated that the number of sites binding with the DMSO molecule and the successive ordered sequence of the ordered unit of the triple helix are changed by carboxylation.

A new endoscopic technique for suspension of esophageal prosthesis for refractory caustic esophageal strictures.

PubMed

Ancona, E; Guido, E; Cutrone, C; Bocus, P; Rampado, S; Vecchiato, M; Salvador, R; Donach, M; Battaglia, G

2008-01-01

There is no clear consensus concerning the best endoscopic treatment of benign refractory esophageal strictures due to caustic ingestion. Different procedures are currently used: frequent multiple dilations, retrievable self-expanding stent, nasogastric intubation and surgery. We describe a new technique to fix a suspended esophageal silicone prosthesis to the neck in benign esophageal strictures; this permits us to avoid the frequent risk of migration of the expandable metallic or plastic stents. Under general anesthesia a rigid esophagoscope was placed in the patient's hypopharynx. Using transillumination from the optical device, the patient's neck was pierced with a needle. A n.0 monofilament surgical wire was pushed into the needle, grasped by a standard foreign body forceps through the esophagoscope and pulled out of the mouth (as in percutaneous endoscopic gastrostomy procedure). After tying the proximal end of the silicone prosthesis with the wire, it was placed through the strictures under endoscopic view. This procedure was successfully utilized in four patients suffering from benign refractory esophageal strictures due to caustic ingestion. The prosthesis and its suspension from the neck were well-tolerated until removal (mean duration 4 months). A postoperative transitory myositis was diagnosed in only one patient. One of the most frequent complications of esophageal prostheses in refractory esophageal strictures due to caustic ingestion is distal migration. Different solutions were proposed. For example the suspension of a wire coming from the nose and then fixed behind the ear. This solution is not considered optimal because of patient complaints and moreover the aesthetic aspect is compromised. The procedure we utilized in four patients utilized the setting of a silicone tube hanging from the neck in a way similar to that of endoscopic pharyngostomy. This solution is a valid alternative both for quality of life and for functional results.

Fluorescence Determination of Tryptophan Side-Chain Accessibility and Dynamics in Triple-Helical Collagen-Like Peptides

PubMed Central

Simon-Lukasik, Kristine V.; Persikov, Anton V.; Brodsky, Barbara; Ramshaw, John A. M.; Laws, William R.; Alexander Ross, J. B.; Ludescher, Richard D.

2003-01-01

We report tryptophan fluorescence measurements of emission intensity, iodide quenching, and anisotropy that describe the environment and dynamics at X and Y sites in stable collagen-like peptides of sequence (Gly-X-Y)n. About 90% of tryptophans at both sites have similar solvent exposed fluorescence properties and a lifetime of 8.5–9 ns. Analysis of anisotropy decays using an associative model indicates that these long lifetime populations undergo rapid depolarizing motion with a 0.5 ns correlation time; however, the extent of fast motion at the Y site is considerably less than the essentially unrestricted motion at the X site. About 10% of tryptophans at both sites have a shorter (∼3 ns) lifetime indicating proximity to a protein quenching group; these minor populations are immobile on the peptide surface, depolarizing only by overall trimer rotation. Iodide quenching indicates that tryptophans at the X site are more accessible to solvent. Side chains at X sites are more solvent accessible and considerably more mobile than residues at Y sites and can more readily fluctuate among alternate intermolecular interactions in collagen fibrils. This fluorescence analysis of collagen-like peptides lays a foundation for studies on the structure, dynamics, and function of collagen and of triple-helical junctions in gelatin gels. PMID:12524302

A Rare Case of Anal and Perianal Chemical Burn in a Child due to Potassium Permanganate Crystals.

PubMed

Dash, Suvashis; Bhojani, Jatin; Sharma, Sharadendu

2018-02-09

Many chemicals used as medical treatments can cause chemical burns as an untoward side effect. One of such chemicals is potassium permanganate. It is a caustic chemical used as a disinfectant. The most common sites of burn by potassium permanganate are exposed sites like the face and hands. Chemical burns in the perianal and anal region are rare in clinical practice and even sparser in the pediatric age group. In this article, we report a case of perianal and anal chemical burn in an 18-month-old, male child, caused by potassium permanganate crystal applied wrongly for the treatment of pinworm infestation. As a chemical burn in this region can have serious complications, it is necessary to be vigilant when using such chemicals in these cases. Early and timely management in such cases leads to good outcomes. This is the first of such cases of chemical burn caused by potassium permanganate in the anal and perianal region.

A study of Propfan propagation noise

NASA Technical Reports Server (NTRS)

Sim, Ben W.-C.; George, A. R.

1993-01-01

A study of Propfan far-field noise is carried out based on geometrical acoustics theory. The analysis traces the acoustic rays and ray tube areas carrying the acoustic disturbances to the far-field. Sound attenuation due to nonlinear steepening, atmospheric absorption and turbulence scattering are also investigated. A comparison of our prediction methodology with experimental acoustics measurement shows good agreement. Geometrical decay and atmospheric absorption are identified as the primary noise attenuating mechanisms. Nonlinear effects are negligible. It is determined that the acoustic footprints of advanced propellers are dominated by caustics. Details of the formation of these caustics may provide a basis for future noise minimization efforts.

Extraction of caustic potash from spent tea for biodiesel Production

NASA Astrophysics Data System (ADS)

Sulaiman, Sarina; Faiz Che Fisol, Ahmad; Sharikh, Atikah Mohamed; Noraini Jimat, Dzun; Jamal, Parveen

2018-01-01

Biodiesel is an alternative to non-renewable fossil fuels due to its low gas emission and economical value. This study aims to extract caustic potash (KOH) from spent tea and to optimize the transesterfication process based on parameters such as amount of catalyst, reaction temperature and methanol to oil ratio. The spent tea was first dried at 60°C prior to calcination at 600°C for two hours. Caustic Potash were extracted from the calcined spent tea. The transesterification process was done based on Design of Experiments (DOE) to study the effects of amount of catalyst ranging from 0.5 wt % to 2.5 wt %, reaction temperature from 55°C to 65°C and methanol to oil ratio from 6:1 to 12:1 at a constant agitation rate of 300 rpm for three hours. The calcined spent tea produced was recorded the highest at 54.3 wt % and the extracted catalyst was 2.4 wt %. The optimized biodiesel yield recorded was 56.95% at the optimal conditions of 2.5 wt % amount of catalyst, 65°C reaction temperature and 9:1 methanol to oil ratio.

Co-treatment of spent cathode carbon in caustic and acid leaching process under ultrasonic assisted for preparation of SiC.

PubMed

Yuan, Jie; Xiao, Jin; Li, Fachuang; Wang, Bingjie; Yao, Zhen; Yu, Bailie; Zhang, Liuyun

2018-03-01

Spent cathode carbon (SCC) from aluminum electrolysis has been treated in ultrasonic-assisted caustic leaching and acid leaching process, and purified SCC used as carbon source to synthesize silicon carbide (SiC) was investigated. Chemical and mineralogical properties have been characterized by X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), and thermogravimetry and differential scanning calorimetry (TGA-DSC). Various experimental factors temperature, time, liquid-solid ratio, ultrasonic power, and initial concentration of alkali or acid affecting on SCC leaching result were studied. After co-treatment with ultrasonic-assisted caustic leaching and acid leaching, carbon content of leaching residue was 97.53%. SiC power was synthesized by carbothermal reduction at 1600 °C, as a result of yield of 76.43%, and specific surface area of 4378 cm 2 /g. This is the first report of using purified SCC and gangue to prepare SiC. The two industrial wastes have been used newly as secondary sources. Furthermore, ultrasonic showed significant effect in SCC leaching process. Copyright © 2017 Elsevier B.V. All rights reserved.

Biotreatment of refinery spent-sulfidic caustic using an enrichment culture immobilized in a novel support matrix.

PubMed

Conner, J A; Beitle, R R; Duncan, K; Kolhatkar, R; Sublette, K L

2000-01-01

Sodium hydroxide solutions are used in petroleum refining to remove hydrogen sulfide (H2S) and mercaptans from various hydrocarbon streams. The resulting sulfide-laden waste stream is called spent-sulfidic caustic. An aerobic enrichment culture was previously developed using a gas mixture of H2S and methyl-mercaptan (MeSH) as the sole energy source. This culture has now been immobilized in a novel support matrix, DuPont BIO-SEP beads, and is used to bio-treat a refinery spent-sulfidic caustic containing both inorganic sulfide and mercaptans in a continuous flow, fluidized-bed column bioreactor. Complete oxidation of both inorganic and organic sulfur to sulfate was observed with no breakthrough of H2S and < 2 ppmv of MeSH produced in the bioreactor outlet gas. Excessive buildup of sulfate (> 12 g/L) in the bioreactor medium resulted in an upset condition evidenced by excessive MeSH breakthrough. Therefore, bioreactor performance was limited by the steady-state sulfate concentration. Further improvement in volumetric productivity of a bioreactor system based on this enrichment culture will be dependent on maintenance of sulfate concentrations below inhibitory levels.

Interaction of aerodynamic noise with laminar boundary layers in supersonic wind tunnels

NASA Technical Reports Server (NTRS)

Schopper, M. R.

1984-01-01

The interaction between incoming aerodynamic noise and the supersonic laminar boundary layer is studied. The noise field is modeled as a Mach wave radiation field consisting of discrete waves emanating from coherent turbulent entities moving downstream within the supersonic turbulent boundary layer. The individual disturbances are likened to miniature sonic booms and the laminar boundary layer is staffed by the waves as the sources move downstream. The mean, autocorrelation, and power spectral density of the field are expressed in terms of the wave shapes and their average arrival rates. Some consideration is given to the possible appreciable thickness of the weak shock fronts. The emphasis in the interaction analysis is on the behavior of the shocklets in the noise field. The shocklets are shown to be focused by the laminar boundary layer in its outer region. Borrowing wave propagation terminology, this region is termed the caustic region. Using scaling laws from sonic boom work, focus factors at the caustic are estimated to vary from 2 to 6 for incoming shocklet strengths of 1 to .01 percent of the free stream pressure level. The situation regarding experimental evidence of the caustic region is reviewed.

F-Area Acid/Caustic Basin groundwater monitoring report. First quarter 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1995-06-01

During first quarter 1995, samples from the FAC monitoring wells at the F-Area Acid/Caustic Basin were collected and analyzed for herbicides/pesticides, indicator parameters, metals, nitrate, radionuclide indicators, volatile organic compounds, and other constituents. Piezometer FAC 5P and monitoring well FAC 6 were dry and could not be sampled. New monitoring wells FAC 9C, 10C, 11C, and 12C were completed in the Barnwell/McBean aquifer and were sampled for the first time during third quarter 1994 (first quarter 1995 is the third of four quarters of data required to support the closure of the basin). Analytical results that exceeded final Primary Drinkingmore » Water Standards (PDWS), other Savannah River Site (SRS) Flag 2 criteria, or the SRS turbidity standard of 50 NTU during the quarter were as follows: gross alpha exceeded the final PDWS and aluminum, iron, manganese, and total alpha-emitting radium exceeded the SRS Flag 2 criteria in one or more of the FAC wells. Turbidity exceeded the SRS standard (50 NTU) in wells FAC 3 and 11C. Groundwater flow direction and rate in the water table beneath the F-Area Acid/Caustic Basin were similar to past quarters.« less

Solvent and substituent effects on aggregation constants of perylene bisimide π-stacks--a linear free energy relationship analysis.

PubMed

Chen, Zhijian; Fimmel, Benjamin; Würthner, Frank

2012-08-14

A series of six perylene bisimides (PBIs) with hydrophilic and hydrophobic side chains at the imide nitrogens were applied for a comparative study of the solvent and structural effects on the aggregation behaviour of this class of dyes. A comparison of the binding constants in tetrachloromethane at room temperature revealed the highest binding constant of about 10(5) M(-1) for a PBI bearing 3,4,5-tridodecyloxyphenyl substituents at the imide nitrogens, followed by 3,4,5-tridodecylphenyl and alkyl-substituted PBIs, whereas no aggregation could be observed in the accessible concentration range for PBIs equipped with bulky 2,6-diisopropylphenyl substituents at the imide nitrogens. The aggregation behaviour of three properly soluble compounds was investigated in 17 different solvents covering a broad polarity range from nonpolar n-hexane to highly polar DMSO and water. Linear free energy relationships (LFER) revealed a biphasic behaviour between Gibbs free energies of aggregation and common empirical solvent polarity scales indicating particularly strong π-π stacking interactions in nonpolar aliphatic and polar alcoholic solvents whilst the weakest binding is observed in dichloromethane and chloroform. Accordingly, PBI aggregation is dominated by electrostatic interactions in nonpolar solvents and by solvophobic interactions in protic solvents. In water, the aggregation constant is increased far beyond LFER expectations pointing at a pronounced hydrophobic effect.

Reconstructing Solvent Density of Myoglobin Unit Cell from Proximal Radial Distribution Functions of Amino Acids

NASA Astrophysics Data System (ADS)

Galbraith, Madeline; Lynch, Gc; Pettitt, Bm

Understanding the solvent density around a protein crystal structure is an important step for refining accurate crystal structures for use in dynamics simulations or in free energy calculations. The free energy of solvation has typically been approximated using an implicit continuum solvent model or an all atom MD simulation, with a trade-off between accuracy and computation time. For proteins, using precomputed proximal radial distribution functions (pRDFs) of the solvent to reconstruct solvent density on a grid is much faster than all atom MD simulations and more accurate than using implicit solvent models. MD simulations were run for the 20 common amino acids and pRDFs were calculated for several atom type data sets with and without hydrogens, using atom types representative of amino acid side chain atoms. Preliminary results from reconstructions suggest using a data set with 15 heavy atoms and 3 hydrogen yields results with the lowest error without a tradeoff on time. The results of using precomputed pRDFs to reconstruct the solvent density of water for the myoglobin (pdb ID 2mgk) unit cell quantifies the accuracy of the method in comparison with the crystallographic data. Funding Acknowledgement: This research was funded by the CPRIT Summer Undergraduate Program in Computational Cancer Biology, training Grant award RP 140113 from the Cancer Prevention & Research Institute of Texas (CPRIT).

Field-portable supercritical CO{sub 2} extractor

DOEpatents

Wright, B.W.; Zemanian, T.S.; Robins, W.H.; Woodcock, L.J.

1997-06-10

The present invention is an apparatus for extracting organic compounds from solid materials. A generator vessel has a removable closure for receiving a solid or liquid solvent which is heated with a resistive heating element to a gaseous or supercritical phase. The removable closure is unencumbered because the side wall is penetrated with an outlet for the gaseous or supercritical solvent. The generator vessel further has a pressure transducer that provides an electronic signal related to pressure of the gaseous or supercritical solvent. The apparatus of the present invention further includes at least one extraction cell having a top and a bottom and a wall extending there between, wherein the bottom is sealably penetrated by an inlet for gaseous or supercritical solvent received through a manifold connected to the outlet, the top having an easy-open removable closure cap, and the wall having an outlet port. Finally, a permeable sample cartridge is included for holding the solid materials and to provide radial-flow of the extraction fluid, which is placed within the extraction cell. 10 figs.

Field-portable supercritical CO.sub.2 extractor

DOEpatents

Wright, Bob W.; Zemanian, Thomas S.; Robins, William H.; Woodcock, Leslie J.

1997-01-01

The present invention is an apparatus for extracting organic compounds from solid materials. A generator vessel has a removable closure for receiving a solid or liquid solvent which is heated with a resistive heating element to a gaseous or supercritical phase. The removable closure is unencumbered because the side wall is penetrated with an outlet for the gaseous or supercritical solvent. The generator vessel further has a pressure transducer that provides an electronic signal related to pressure of the gaseous or supercritical solvent. The apparatus of the present invention further includes at least one extraction cell having a top and a bottom and a wall extending therebetween, wherein the bottom is sealably penetrated by an inlet for gaseous or supercritical solvent received through a manifold connected to the outlet, the top having an easy-open removable closure cap, and the wall having an outlet port. Finally, a permeable sample cartridge is included for holding the solid materials and to provide radial-flow of the extraction fluid, which is placed within the extraction cell.

Comparison of polymer induced and solvent induced trypsin denaturation: the role of hydrophobicity.

PubMed

Jasti, Lakshmi S; Fadnavis, Nitin W; Addepally, Uma; Daniels, Siona; Deokar, Sarika; Ponrathnam, Surendra

2014-04-01

Trypsin adsorption from aqueous buffer by various copolymers of allyl glycidyl ether-ethylene glycol dimethacrylate (AGE-EGDM) copolymer with varying crosslink density increases with increasing crosslink density and the effect slowly wears off after reaching a plateau at 50% crosslink density. The copolymer with 25% crosslink density was reacted with different amines with alkyl/aryl side chains to obtain a series of copolymers with 1,2-amino alcohol functional groups and varying hydrophobicity. Trypsin binding capacity again increases with hydrophobicity of the reacting amine and a good correlation between logPoctanol of the amine and protein binding is observed. The bound trypsin is denatured to the extent of 90% in spite of the presence of hydrophilic hydroxyl and amino groups. The behavior was comparable to that in mixtures of aqueous buffer and water-miscible organic co-solvents where the solvent concentration required to deactivate 50% of the enzyme (C50) is dependent on logPoctanol of the co-solvent. Copyright © 2014 Elsevier B.V. All rights reserved.

The docking of chiral analytes on proline-based chiral stationary phases: A molecular dynamics study of selectivity.

PubMed

Ashtari, M; Cann, N M

2015-08-28

Molecular dynamics simulations are employed to examine the selectivity of four proline-based chiral stationary phases in two solvent environments, a relatively apolar n-hexane/2-propanol solvent and a polar water/methanol solvent. The four chiral surfaces are based on a BOC-terminated diproline, a TMA-terminated diproline, a TMA-terminated triproline and a TMA-terminated hexaproline. This range of chiral selectors allows an analysis of the impact of oligomer length and terminal group on selectivity while the two solvent environments indicate the impact of solvent hydrogen bonding and polarity. The selector-analyte interactions are examined for six closely related analytes that each have an aromatic moiety, a hydrogen, and an alcohol group directly bonded to the stereocenter. The analytes differ in the nature of the aromatic group (phenyl or anthracyl), in the attachment point (to the central ring or a side ring in the anthracyl), and in the fourth group bonded to the carbon (CH3, CF3, or C2H5). For each of the 48 solvent+selector+analyte systems, selectivity factors are calculated and, when possible, compared to experiment. The docking mode for these proline-based selectors is analyzed. Copyright © 2015 Elsevier B.V. All rights reserved.

Turbulence Scales, Rise Times, Caustics, and the Simulation of Sonic Boom Propagation

NASA Technical Reports Server (NTRS)

Pierce, Allan D.

1996-01-01

The general topic of atmospheric turbulence effects on sonic boom propagation is addressed with especial emphasis on taking proper and efficient account of the contributions of the portion oi the turbulence that is associated with extremely high wavenumber components. The recent work reported by Bart Lipkens in his doctoral thesis is reexamined to determine whether the good agreement between his measured rise times with the 1971 theory of the author is fortuitous. It is argued that Lipken's estimate of the distance to the first caustic was a gross overestimate because of the use of a sound speed correlation function shaped like a gaussian curve. In particular, it is argued that the expected distance to the first caustic varies with the kinematic viscosity nu and the energy epsilon dissipated per unit mass per unit time, and the sound speed c as : d(sub first caustic) = nu(exp 7/12) c(exp 2/3)/ epsilon(exp 5/12)(nu x epsilon/c(exp 4))(exp a), where the exponent a is greater than -7/12 and can be argued to be either O or 1/24. In any event, the surprising aspect of the relationship is that it actually goes to zero as the viscosity goes to zero with s held constant. It is argued that the apparent overabundance of caustics can be grossly reduced by a general computational and analytical perspective that partitions the turbulence into two parts, divided by a wavenumber k(sub c). Wavenumbers higher than kc correspond to small-scale turbulence, and the associated turbulence can be taken into account by a renormalization of the ambient sound speed so that the result has a small frequency dependence that results from a spatial averaging over of the smaller-scale turbulent fluctuations. Selection of k(sub c). can be made so large that only a very small number of caustics are encountered if one adopts the premise that the frequency dispersion of pulses is caused by that part of the turbulence spectrum which lies in the inertial range originally predicted by Kolmogoroff. The acoustic propagating wave's dispersion relation has the acoustic wavenumber being of the form k = (omega/c) + F(omega), where c is a spatially averaged sound speed and where, for mechanical turbulence, the extra term F(omega) must depend on only the angular frequency omega, the sound speed c, and the turbulent energy dissipation epsilon per unit fluid mass and per unit time. If the turbulence is weak, then the quantity F(omega) has to be of second order in the portions of the turbulent fluid velocity in the inertial range, so, following Kolmogoroff's reasoning, it must vary with epsilon as epsilon(exp 2/3). Simple dimensional analysis then reveals that F(omega) is K epsilon(exp 2/3) c(exp -7/3) omega(exp l/3), K being a universal dimensionless complex constant.

40 CFR 63.6015 - What definitions apply to this subpart?

Code of Federal Regulations, 2010 CFR

2010-07-01

... cements, bead cements, tire building cements and solvents, green tire spray, blemish repair paints, side... in tire component identification; component storage; tire building; tire curing; and tire repair... of warm-up mills, extruders, calendars, tire building, or other tire component and tire manufacturing...

Poly(ethylene oxide) functionalization

DOEpatents

Pratt, Russell Clayton

2014-04-08

A simple procedure is provided by which the hydroxyl termini of poly(ethylene oxide) can be appended with functional groups to a useful extent by reaction and precipitation. The polymer is dissolved in warmed toluene, treated with an excess of organic base and somewhat less of an excess of a reactive acylating reagent, reacted for several hours, then precipitated in isopropanol so that the product can be isolated as a solid, and salt byproducts are washed away. This procedure enables functionalization of the polymer while not requiring laborious purification steps such as solvent-solvent extraction or dialysis to remove undesirable side products.

Kinetic evaluation of the solvolysis of isobutyl chloro- and chlorothioformate esters

PubMed Central

McAneny, Matthew J; Choi, Song Hee

2011-01-01

Summary The specific rates of solvolysis of isobutyl chloroformate (1) are reported at 40.0 °C and those for isobutyl chlorothioformate (2) are reported at 25.0 °C, in a variety of pure and binary aqueous organic mixtures with wide ranging nucleophilicity and ionizing power. For 1, we also report the first-order rate constants determined at different temperatures in pure ethanol (EtOH), methanol (MeOH), 80% EtOH, and in both 97% and 70% 2,2,2-trifluoroethanol (TFE). The enthalpy (ΔH≠) and entropy (ΔS≠) of activation values obtained from Arrhenius plots for 1 in these five solvents are reported. The specific rates of solvolysis were analyzed using the extended Grunwald–Winstein equation. Results obtained from correlation analysis using this linear free energy relationship (LFER) reinforce our previous suggestion that side-by-side addition–elimination and ionization mechanisms operate, and the relative importance is dependent on the type of chloro- or chlorothioformate substrate and the solvent. PMID:21647255

Origins of pressure-induced protein transitions.

PubMed

Chalikian, Tigran V; Macgregor, Robert B

2009-12-18

The molecular mechanisms underlying pressure-induced protein denaturation can be analyzed based on the pressure-dependent differences in the apparent volume occupied by amino acids inside the protein and when they are exposed to water in an unfolded conformation. We present here an analysis for the peptide group and the 20 naturally occurring amino acid side chains based on volumetric parameters for the amino acids in the interior of the native state, the micelle-like interior of the pressure-induced denatured state, and the unfolded conformation modeled by N-acetyl amino acid amides. The transfer of peptide groups from the protein interior to water becomes increasingly favorable as pressure increases. Thus, solvation of peptide groups represents a major driving force in pressure-induced protein denaturation. Polar side chains do not appear to exhibit significant pressure-dependent changes in their preference for the protein interior or solvent. The transfer of nonpolar side chains from the protein interior to water becomes more unfavorable as pressure increases. We conclude that a sizeable population of nonpolar side chains remains buried inside a solvent-inaccessible core of the pressure-induced denatured state. At elevated pressures, this core may become packed almost as tightly as the interior of the native state. The presence and partial disappearance of large intraglobular voids is another driving force facilitating pressure-induced denaturation of individual proteins. Our data also have implications for the kinetics of protein folding and shed light on the nature of the folding transition state ensemble.

Polyelectrolyte-Surfactant Complexes: A New Class of Organogelators

NASA Astrophysics Data System (ADS)

Cavicchi, Kevin; Liu, Yuqing; Guzman, Gustavo

2011-03-01

Polyelectrolyte-surfactant complexes (PE-SURFs) are a class of polymers generated by neutralizing a polyelectrolyte with an oppositely charged surfactant. It has been found that PE-SURFs composed of polystyrene sulfonate and long chain alkyl dimethyl amines act as good organogelators for a range of hydrophobic, organic solvents. Thermo-reversible organogels are formed by heating and cooling PE-SURF/solvent solutions. The gel transition temperature is influenced by the degree of polymerization, the length of the alkyl side-chain, the solubility parameter of the solvent, and the concentration of the gelator. Freeze-drying and scanning electron microscopy characterization of the resultant xerogels shows the formation of rod- and plate-like network morphologies depending on the system parameters. This behavior is consistent with gelation driven by the self-assembly of the amphiphilic PE-SURFs into micellar networks.

MICROBIAL COMETABOLISM OF RECALCITRANT CHEMICALS IN CONTAMINATED AIR STREAMS

EPA Science Inventory

Chlorinated Solvents: The treatment system consists of a laboratory-scale hollow fiber membrane (HFM) module containing a center baffle and a radial cross-flow pattern on the shell side of the fibers. The shell and lumen fluids are contacting in a counter-current f...

Development of a beam builder for automatic fabrication of large composite space structures

NASA Technical Reports Server (NTRS)

Bodle, J. G.

1979-01-01

The composite material beam builder which will produce triangular beams from pre-consolidated graphite/glass/thermoplastic composite material through automated mechanical processes is presented, side member storage, feed and positioning, ultrasonic welding, and beam cutoff are formed. Each process lends itself to modular subsystem development. Initial development is concentrated on the key processes for roll forming and ultrasonic welding composite thermoplastic materials. The construction and test of an experimental roll forming machine and ultrasonic welding process control techniques are described.

STS-7 crewmembers during meal preparation on middeck

NASA Technical Reports Server (NTRS)

1983-01-01

On middeck, Mission Specialist (MS) Thagard and MS Ride select food containers from forward modular locker single tray assembly (ASSY) and prepare containers for heating while Pilot Hauck (with mustache) adjusts SONY Walkman and MS Fabian opens containers. Carry-on food warmer appears overhead and control panel ML86B and Continuous Flow Electrophoresis System (CFES) fluid systems module appear on port side wall. Hauck wears a TFNG t-shirt as a tribute to the 1978 class of NASA astronauts.

Simulation of Mirror Electron Microscopy Caustic Images in Three-Dimensions

NASA Astrophysics Data System (ADS)

Kennedy, S. M.; Zheng, C. X.; Jesson, D. E.

A full, three-dimensional (3D) ray tracing approach is developed to simulate the caustics visible in mirror electron microscopy (MEM). The method reproduces MEM image contrast resulting from 3D surface relief. To illustrate the potential of the simulation methods, we study the evolution of crater contrast associated with a movie of GaAs structures generated by the droplet epitaxy technique. Specifically, we simulate the image contrast resulting from both a precursor stage and the final crater morphology which is consistent with an inverted pyramid consisting of (111) facet walls. The method therefore facilities the study of how self-assembled quantum structures evolve with time and, in particular, the development of anisotropic features including faceting.

Interaction-component analysis of the hydration and urea effects on cytochrome c

NASA Astrophysics Data System (ADS)

Yamamori, Yu; Ishizuka, Ryosuke; Karino, Yasuhito; Sakuraba, Shun; Matubayasi, Nobuyuki

2016-02-01

Energetics was analyzed for cytochrome c in pure-water solvent and in a urea-water mixed solvent to elucidate the solvation effect in the structural variation of the protein. The solvation free energy was computed through all-atom molecular dynamics simulation combined with the solution theory in the energy representation, and its correlations were examined over sets of protein structures against the electrostatic and van der Waals components in the average interaction energy of the protein with the solvent and the excluded-volume component in the solvation free energy. It was observed in pure-water solvent that the solvation free energy varies in parallel to the electrostatic component with minor roles played by the van der Waals and excluded-volume components. The effect of urea on protein structure was then investigated in terms of the free-energy change upon transfer of the protein solute from pure-water solvent to the urea-water mixed solvent. The decomposition of the transfer free energy into the contributions from urea and water showed that the urea contribution is partially canceled by the water contribution and governs the total free energy of transfer. When correlated against the change in the solute-solvent interaction energy upon transfer and the corresponding changes in the electrostatic, van der Waals, and excluded-volume components, the transfer free energy exhibited strong correlations with the total change in the solute-solvent energy and its van der Waals component. The solute-solvent energy was decomposed into the contributions from the protein backbone and side chain, furthermore, and neither of the contributions was seen to be decisive in the correlation to the transfer free energy.

Systematic Assessment of Seven Solvent and Solid-Phase Extraction Methods for Metabolomics Analysis of Human Plasma by LC-MS

NASA Astrophysics Data System (ADS)

Sitnikov, Dmitri G.; Monnin, Cian S.; Vuckovic, Dajana

2016-12-01

The comparison of extraction methods for global metabolomics is usually executed in biofluids only and focuses on metabolite coverage and method repeatability. This limits our detailed understanding of extraction parameters such as recovery and matrix effects and prevents side-by-side comparison of different sample preparation strategies. To address this gap in knowledge, seven solvent-based and solid-phase extraction methods were systematically evaluated using standard analytes spiked into both buffer and human plasma. We compared recovery, coverage, repeatability, matrix effects, selectivity and orthogonality of all methods tested for non-lipid metabolome in combination with reversed-phased and mixed-mode liquid chromatography mass spectrometry analysis (LC-MS). Our results confirmed wide selectivity and excellent precision of solvent precipitations, but revealed their high susceptibility to matrix effects. The use of all seven methods showed high overlap and redundancy which resulted in metabolite coverage increases of 34-80% depending on LC-MS method employed as compared to the best single extraction protocol (methanol/ethanol precipitation) despite 7x increase in MS analysis time and sample consumption. The most orthogonal methods to methanol-based precipitation were ion-exchange solid-phase extraction and liquid-liquid extraction using methyl-tertbutyl ether. Our results help facilitate rational design and selection of sample preparation methods and internal standards for global metabolomics.

Systematic Assessment of Seven Solvent and Solid-Phase Extraction Methods for Metabolomics Analysis of Human Plasma by LC-MS

PubMed Central

Sitnikov, Dmitri G.; Monnin, Cian S.; Vuckovic, Dajana

2016-01-01

The comparison of extraction methods for global metabolomics is usually executed in biofluids only and focuses on metabolite coverage and method repeatability. This limits our detailed understanding of extraction parameters such as recovery and matrix effects and prevents side-by-side comparison of different sample preparation strategies. To address this gap in knowledge, seven solvent-based and solid-phase extraction methods were systematically evaluated using standard analytes spiked into both buffer and human plasma. We compared recovery, coverage, repeatability, matrix effects, selectivity and orthogonality of all methods tested for non-lipid metabolome in combination with reversed-phased and mixed-mode liquid chromatography mass spectrometry analysis (LC-MS). Our results confirmed wide selectivity and excellent precision of solvent precipitations, but revealed their high susceptibility to matrix effects. The use of all seven methods showed high overlap and redundancy which resulted in metabolite coverage increases of 34–80% depending on LC-MS method employed as compared to the best single extraction protocol (methanol/ethanol precipitation) despite 7x increase in MS analysis time and sample consumption. The most orthogonal methods to methanol-based precipitation were ion-exchange solid-phase extraction and liquid-liquid extraction using methyl-tertbutyl ether. Our results help facilitate rational design and selection of sample preparation methods and internal standards for global metabolomics. PMID:28000704

Solvent-free iodination of organic molecules using the I(2)/urea-H(2)O(2) reagent system.

PubMed

Pavlinac, Jasminka; Zupan, Marko; Stavber, Stojan

2007-02-21

Introduction of iodine under solvent-free conditions into several aromatic compounds activated toward electrophilic functionalization was found to proceed efficiently using elemental iodine in the presence of a solid oxidizer, the urea-H(2)O(2) (UHP) adduct. Two types of iodo-functionalization through an electrophilic process were observed: iodination of an aromatic ring, and side-chain iodo-functionalization in the case of arylalkyl ketones. Two reaction routes were established based on the required substrate : iodine : oxidizer ratio for the most efficient iodo-transformation, and the role of UHP was elucidated in each route. The first, requiring a 1 : 0.5 : 0.6 stoichiometric ratio of substrate to iodine to UHP, followed the atom economy concept in regard to iodine and was valid in the case of aniline, 4-t-Bu-phenol, 1,2-dimethoxy benzene, 1,3-dimethoxy benzene, 1,2,3-trimethoxy benzene, 1,2,4-trimethoxy benzene, 1,3,5-trimethoxy benzene, 1-indanone and 1-tetralone. The second reaction route, where a 1 : 1 : 1 stoichiometric ratio of substrate : I(2) : UHP was needed for efficient iodination, was suitable for side-chain iodo-functionalization of acetophenone and methoxy-substituted acetophenones. Moreover, addition of iodine to 1-octene and some phenylacetylenic derivatives was found to proceed efficiently without the presence of any oxidizer and solvent at room temperature.

Investigation of light-induced conformation changes in spiropyran-modified succinylated poly(L-lysine).

PubMed

Cooper, T M; Stone, M O; Natarajan, L V; Crane, R L

1995-08-01

To determine the maximum range of coupling between side-chain photochromism and polypeptide conformation change, we modified the carboxylate side chains of succinylated poly(L-lysine) with a spiropyran to form polypeptide I. The extent of modification was determined to be 35.5%. The spacer group length between the polypeptide alpha-carbon and the dye was 12 atoms, providing minimum polypeptide-dye interaction. Conformation changes were monitored by circular dichroism as a function of light adaptation and solvent composition (hexafluoroisopropanol [HFIP] vs trifluoroethanol [TFE]). Under all solvent compositions, the dark-adapted dye was in the merocyanine form. Light adaptation by visible light converted the dye to the spiropyran form. When dissolved in TFE, I adopted a helical conformation insensitive to light adaptation. With increasing percentage HFIP, a solvent-induced helix-to-coil transition was observed around 80% (vol/vol) HFIP. At 100% HFIP, both light- and dark-adapted forms of I were in the coil state. Near the midpoint of the solvent-induced helix-to-coil transition, light adaptation caused conformation changes. Applying helix-to-coil transition theory, we measured a statistically significant difference in coil segment-HFIP binding constant for light- vs dark-adapted solutions (6.38 +/- 0.03 M-1 vs 6.56 +/- 0.03 M-1), but not for the nucleation parameter sigma (1.2 +/- 0.4 10(-3) vs 1.3 +/- 0.3 x 10(-3). The small binding constant difference translated to a light-induced binding energy difference of 17 cal/mol/monomer. Near the midpoint of the helix-to-coil transition, collective interactions between monomer units made possible the translation of a small energy difference (less than RT) into large macromolecular conformation changes.(ABSTRACT TRUNCATED AT 250 WORDS)

Titanium-titanium modular neck for primary THA. Result of a prospective series of 170 cemented THA with a minimum follow-up of 5 years.

PubMed

Ollivier, M; Parratte, S; Galland, A; Lunebourg, A; Flecher, X; Argenson, J-N

2015-04-01

Although they have been in use since the end of the 1980s, modular titanium neck components are associated with a risk of wear or fracture, and their safety has recently become a subject of debate and has never been evaluated in a consecutive series of patients. The goal of this study was to evaluate: revision-free survival of these implants after a minimum follow-up of 5 years; clinical and radiographic results; and the potential complications associated with the use of modular titanium neck components. The use of titanium modular neck on cemented titanium THA is safe at a minimum follow-up of 5 years. Between January 2006 and December 2008, we prospectively followed 170 patients (170 hips) who underwent primary anatomical THA with a modular cemented titanium stem design implant. The indications were unilateral THA for primary (n=160) or secondary (n=10) hip osteoarthritis (aseptic osteonecrosis of the femoral head or hip dysplasia). Mean age of patients was 75.4±5.8 years old (52-85), and mean BMI was 26.1±4.5 kg/m(2) (16.6-42.1). Patients were operated on by a modified Watson-Jones anterolateral approach based on preoperative 2D planning. All patients underwent annual clinical and radiological follow-up by an independent observer. At a mean follow-up of 71±8 months (60-84), 5 patients died and 7 were lost to follow-up. There was no revision of THA after a maximum follow-up of 84 months. The Harris score improved significantly from 50.4±11.3 (0-76) preoperatively to 84.5±15.2 (14-100) at the final follow-up. There was no difference in postoperative femoral offset or the position of the center of rotation compared to the opposite side. On the other hand, the neck-shaft angle (NSA) and limb length were corrected (2±5° [-11 to +14°] and 2.16±3.6 mm [-7.4 to +12.7 mm]) respectively. Fifteen patients (9%) had limb length discrepancies of more than 5 mm and 4 patients (2%) of more than 10 mm. There were no complications due to the modular implant design. Our study suggests that the use of cemented titanium implants with a modular titanium stem is safe at a follow-up of 5 years. The modular design does not prevent limb length discrepancies but restores femoral offset. IV: prospective, non-comparative study. Copyright © 2015 Elsevier Masson SAS. All rights reserved.

Extended Hansen solubility approach: naphthalene in individual solvents.

PubMed

Martin, A; Wu, P L; Adjei, A; Beerbower, A; Prausnitz, J M

1981-11-01

A multiple regression method using Hansen partial solubility parameters, delta D, delta p, and delta H, was used to reproduce the solubilities of naphthalene in pure polar and nonpolar solvents and to predict its solubility in untested solvents. The method, called the extended Hansen approach, was compared with the extended Hildebrand solubility approach and the universal-functional-group-activity-coefficient (UNIFAC) method. The Hildebrand regular solution theory was also used to calculate naphthalene solubility. Naphthalene, an aromatic molecule having no side chains or functional groups, is "well-behaved', i.e., its solubility in active solvents known to interact with drug molecules is fairly regular. Because of its simplicity, naphthalene is a suitable solute with which to initiate the difficult study of solubility phenomena. The three methods tested (Hildebrand regular solution theory was introduced only for comparison of solubilities in regular solution) yielded similar results, reproducing naphthalene solubilities within approximately 30% of literature values. In some cases, however, the error was considerably greater. The UNIFAC calculation is superior in that it requires only the solute's heat of fusion, the melting point, and a knowledge of chemical structures of solute and solvent. The extended Hansen and extended Hildebrand methods need experimental solubility data on which to carry out regression analysis. The extended Hansen approach was the method of second choice because of its adaptability to solutes and solvents from various classes. Sample calculations are included to illustrate methods of predicting solubilities in untested solvents at various temperatures. The UNIFAC method was successful in this regard.

Modular synthesis and in vitro and in vivo antimalarial assessment of C-10 pyrrole mannich base derivatives of artemisinin.

PubMed

Pacorel, Bénédicte; Leung, Suet C; Stachulski, Andrew V; Davies, Jill; Vivas, Livia; Lander, Hollie; Ward, Stephen A; Kaiser, Marcel; Brun, Reto; O'Neill, Paul M

2010-01-28

In two steps from dihydroartemisinin, a small array of 16 semisynthetic C-10 pyrrole Mannich artemisinin derivatives (7a-p) have been prepared in moderate to excellent yield. In vitro analysis against both chloroquine sensitive and resistant strains has demonstrated that these analogues have nanomolar antimalarial activity, with several compounds being more than 3 times more potent than the natural product artemisinin. In addition to a potent antimalarial profile, these molecules also have very high in vitro therapeutic indices. Analysis of the optimal Mannich side chain substitution for in vitro and in vivo activity reveals that the morpholine and N-methylpiperazine Mannich side chains provide analogues with the best activity profiles, both in vitro and in vivo in the Peter's 4 day test.

Decomposition of banten ilmenite by caustic fusion process for TiO2 photocatalytic applications

NASA Astrophysics Data System (ADS)

Aristanti, Y.; Supriyatna, Y. I.; Masduki, N. P.; Soepriyanto, S.

2018-01-01

Decomposition of Banten ilmenite by caustic fusion process for TiO2 photocatalytic applications has been done. Caustic fusion process using NaOH to obtain sodium titanate compound which is soluble in sulfuric acid (H2SO4) to produces TiOSO4 as a precursor. Synthesis of TiO2 from TiOSO4 precursors by variations of pH hydrolysis are 1.0 (TiO2 A), 1.5 (TiO2 B) and 2.0 (TiO2 C). XRD pattern identified TiO2 structures crystals are anatase phase and traces α-Fe2O3 as an impurity. Presence of Fe2O3 as an impurities give positive effect on TiO2 photocatalytic activity that is to narrower the band gap energy thus facilitates of electrons excitation from valence band to conduction band and enlarge the specific surface area thus reaction between Rhodamin B solution and TiO2 surface can be faster. TiO2 A, TiO2 B and TiO2 C was compared to TiO2 M (commercial TiO2) in Rhodamin B solution for the photocatalytic activity where the maximum TiO2 degradation efficiency was obtained at TiO2 C 80.0 % while TiO2 M 59.8 %.

[Endoscopic contribution in the dilatation of caustic esophagus stenosis].

PubMed

Seydou, Togo; Abdoulaye, Ouattara Moussa; Xing, Li; Zi, Sanogo Zimogo; Sekou, Koumaré; Wen, Yang Shang; Ibrahim, Sankare; Sekou, Toure Cheik Ahmed; Boubacar, Maiga Ibrahim; Saye, Jacque; Jerome, Dakouo Dodino; Dantoumé, Toure Ousmane; Sadio, Yena

2016-01-01

The aim of this work was to present the contribution of the endoscopy in the management of esophageal dilatation for caustic esophageal stenosis (CES). This was a descriptive and prospective study in the thoracic surgery department at the Hospital of Mali. A total of 46 cases of CES is recorded and divided into 4 groups according to the topography of the esophageal lesions. For the different methods of dilatation the number of performed endoscopic support was determined to understand the contribution of endoscopic means in the success of dilatation for CES. The outcome, complications and mortality in the two methods were compared. Fibroscopy was used in 41.30% of patients with Savary Guillard dilators and in 47.82% of patients with Lerut dilators. Video laryngoscopy was used in 58.69% of patients who underwent dilatation with Lerut dilators. The passage of the guide wire was performed in 39.13% under video laryngoscopy and 58.68% under fibroscopy. In comparison of the two methods, there is a significant difference in the occurrence of complications (p=0.04075), general anesthesia (p=0.02287), accessibility (p=0.04805) and mortality (p=0.00402). The CES is a serious disease and under evaluated in Mali. The endoscopies contribute significantly to the success of esophageal dilatation for caustic stenosis in the different methods we used.

Galaxies as High-resolution Telescopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barnacka, Anna, E-mail: abarnacka@cfa.harvard.edu

Recent observations show a population of active galaxies with milliarcsecond offsets between optical and radio emission. Such offsets can be an indication of extreme phenomena associated with supermassive black holes including relativistic jets, binary supermassive black holes, or even recoiling supermassive black holes. However, the multi-wavelength structure of active galaxies at a few milliarcseconds cannot be resolved with direct observations. We propose using strong gravitational lensing to elucidate the multi-wavelength structure of sources. When sources are located close to the caustic of a lensing galaxy, even a small offset in the position of the sources results in a drastic differencemore » in the position and magnification of mirage images. We show that the angular offset in the position of the sources can be amplified more than 50 times in the observed position of mirage images. We find that at least 8% of the observed gravitationally lensed quasars will be in the caustic configuration. The synergy between SKA and Euclid will provide an ideal set of observations for thousands of gravitationally lensed sources in the caustic configuration, which will allow us to resolve the multi-wavelength structure for a large ensemble of sources and to study the physical origin of radio emissions, their connection to supermassive black holes, and their cosmic evolution.« less

Organic fluid permeation through fluoropolymer membranes

DOEpatents

Nemser, Stuart M.; Kosaraju, Praveen; Bowser, John

2015-07-14

Separation of the components of liquid mixtures is achieved by contacting a liquid mixture with a nonporous membrane having a fluoropolymer selectively permeable layer and imposing a pressure gradient across the membrane from feed side to permeate side. Unusually high transmembrane flux is obtained when the membrane is subjected to one or more process conditions prior to separation. These include (a) leaving some residual amount of membrane casting solvent in the membrane, and (b) contacting the membrane with a component of the mixture to be separated for a duration effective to saturate the membrane with the component.

Circulating Current Suppressing Control’s Impact on Arm Inductance Selection for Modular Multilevel Converter

DOE PAGES

Li, Yalong; Jones, Edward A.; Wang, Fred

2016-10-13

Arm inductor in a modular multilevel converter (MMC) is used to limit the circulating current and dc short circuit fault current. The circulating current in MMC is dominated by second-order harmonic, which can be largely reduced with circulating current suppressing control. By analyzing the mechanism of the circulating current suppressing control, it is found that the circulating current at switching frequency becomes the main harmonic when suppression control is implemented. Unlike the second-order harmonic that circulates only within the three phases, switching frequency harmonic also flows through the dc side and may further cause high-frequency dc voltage harmonic. This articlemore » develops the theoretical relationship between the arm inductance and switching frequency circulating current, which can be used to guide the arm inductance selection. The experimental results with a downscaled MMC prototype verify the existence of the switching frequency circulating current and its relationship with arm inductance.« less

Complex network analysis of resting-state fMRI of the brain.

PubMed

Anwar, Abdul Rauf; Hashmy, Muhammad Yousaf; Imran, Bilal; Riaz, Muhammad Hussnain; Mehdi, Sabtain Muhammad Muntazir; Muthalib, Makii; Perrey, Stephane; Deuschl, Gunther; Groppa, Sergiu; Muthuraman, Muthuraman

2016-08-01

Due to the fact that the brain activity hardly ever diminishes in healthy individuals, analysis of resting state functionality of the brain seems pertinent. Various resting state networks are active inside the idle brain at any time. Based on various neuro-imaging studies, it is understood that various structurally distant regions of the brain could be functionally connected. Regions of the brain, that are functionally connected, during rest constitutes to the resting state network. In the present study, we employed the complex network measures to estimate the presence of community structures within a network. Such estimate is named as modularity. Instead of using a traditional correlation matrix, we used a coherence matrix taken from the causality measure between different nodes. Our results show that in prolonged resting state the modularity starts to decrease. This decrease was observed in all the resting state networks and on both sides of the brain. Our study highlights the usage of coherence matrix instead of correlation matrix for complex network analysis.

Extraction, purification and characterization of a protease from Micrococcus sp. VKMM 037.

PubMed

Manikandan, Muthu; Kannan, Vijayaraghavan; Pasić, Lejla

2011-10-01

The haloalkaliphilic bacterium Micrococcus sp. VKMM 037, isolated from an effluent of the caustic soda industry, was found to produce a protease. Maximal proteolytic activity was observed in cell culture grown at 40 degrees C using 2% (w/v) glycerol, 2% (w/v) beef extract and 2% (w/v) peptone as nutrients in medium also containing 0.85 M NaCl with a pH of 10.0. An efficient purification procedure combining ammonium sulphate precipitation and Q-Sepharose ion-exchange chromatography was developed. The purified 41 kDa protease was stable in a temperature range between 20 degrees C and 60 degrees C. The protease remained active over a wide range of pH values (4.0-12.0) and NaCl concentrations (0-3.42 M) with an optimum at pH 10.0 and 0.85 M NaCl, respectively. Furthermore, the enzyme remained stable or was only marginally inhibited in the presence of various organic solvents, surfactants and reducing agents. The purified protease of Micrococcus sp. VKMM 037 efficiently removed blood stains within 40 minutes of treatment. Given the biochemical characteristics determined, this novel protease could be exploited as an additive in the detergent industry and also for the synthesis of biomolecules and the degradation of protein.

Surface Wave Propagation on a Laterally Heterogeneous Earth

NASA Astrophysics Data System (ADS)

Tromp, Jeroen

1992-01-01

Love and Rayleigh waves propagating on the surface of the Earth exhibit path, phase and amplitude anomalies as a result of the lateral heterogeneity of the mantle. In the JWKB approximation, these anomalies can be determined by tracing surface wave trajectories, and calculating phase and amplitude anomalies along them. A time- or frequency -domain JWKB analysis yields local eigenfunctions, local dispersion relations, and conservation laws for the surface wave energy. The local dispersion relations determine the surface wave trajectories, and the energy equations determine the surface wave amplitudes. On an anisotrophic Earth model the local dispersion relation and the local vertical eigenfunctions depend explicitly on the direction of the local wavevector. Apart from the usual dynamical phase, which is the integral of the local wavevector along a raypath, there is an additional variation is phase. This additional phase, which is an analogue of the Berry phase in adiabatic quantum mechanics, vanishes in a waveguide with a local vertical two-fold symmetry axis or a local horizontal mirror plane. JWKB theory breaks down in the vicinity of caustics, where neighboring rays merge and the surface wave amplitude diverges. Based upon a potential representation of the surface wave field, a uniformly valid Maslov theory can be obtained. Surface wave trajectories are determined by a system of four ordinary differential equations which define a three-dimensional manifold in four-dimensional phase space (theta,phi,k_theta,k _phi), where theta is colatitude, phi is longitude, and k_theta and k _phi are the covariant components of the wavevector. There are no caustics in phase space; it is only when the rays in phase space are projected onto configuration space (theta,phi), the mixed spaces (k_theta,phi ) and (theta,k_phi), or onto momentum space (k_theta,k _phi), that caustics occur. The essential strategy is to employ a mixed or momentum space representation of the wavefield in the vicinity of a configuration space caustic.

Effects of solvent concentration and composition on protein dynamics: 13C MAS NMR studies of elastin in glycerol-water mixtures.

PubMed

Demuth, Dominik; Haase, Nils; Malzacher, Daniel; Vogel, Michael

2015-08-01

We use (13)C CP MAS NMR to investigate the dependence of elastin dynamics on the concentration and composition of the solvent at various temperatures. For elastin in pure glycerol, line-shape analysis shows that larger-scale fluctuations of the protein backbone require a minimum glycerol concentration of ~0.6 g/g at ambient temperature, while smaller-scale fluctuations are activated at lower solvation levels of ~0.2 g/g. Immersing elastin in various glycerol-water mixtures, we observe at room temperature that the protein mobility is higher for lower glycerol fractions in the solvent and, thus, lower solvent viscosity. When decreasing the temperature, the elastin spectra approach the line shape for the rigid protein at 245 K for all studied samples, indicating that the protein ceases to be mobile on the experimental time scale of ~10(-5) s. Our findings yield evidence for a strong coupling between elastin fluctuations and solvent dynamics and, hence, such interaction is not restricted to the case of protein-water mixtures. Spectral resolution of different carbon species reveals that the protein-solvent couplings can, however, be different for side chain and backbone units. We discuss these results against the background of the slaving model for protein dynamics. Copyright © 2015 Elsevier B.V. All rights reserved.

A toxic organic solvent-free technology for the preparation of PEGylated paclitaxel nanosuspension based on human serum albumin for effective cancer therapy

PubMed Central

Yin, Tingjie; Dong, Lihui; Cui, Bei; Wang, Lei; Yin, Lifang; Zhou, Jianping; Huo, Meirong

2015-01-01

Clinically, paclitaxel (PTX) is one of most commonly prescribed therapies against a wide range of solid neoplasms. Despite its success, the clinical applicability of PTX (Taxol®) is severely hampered by systemic toxicities induced by Cremophor EL. While attempts to bypass the need for Cremophor EL have been developed through platforms such as Abraxane™, nab™ relies heavily on the use of organic solvents, namely, chloroform. The toxicity introduced by residual chloroform poses a potential risk to patient health. To mitigate the toxicities of toxic organic solvent-based manufacture methods, we have designed a method for the formulation of PTX nanosuspensions (PTX-PEG [polyethylene glycol]-HSA [human serum albumin]) that eliminates the dependence on toxic organic solvents. Coined the solid-dispersion technology, this technique permits the dispersion of PTX into PEG skeleton without the use of organic solvents or Cremophor EL as a solubilizer. Once the PTX-PEG dispersion is complete, the dispersion can be formulated with HSA into nanosuspensions suitable for intravenous administration. Additionally, the incorporation of PEG permits the prolonged circulation through the steric stabilization effect. Finally, HSA-mediated targeting permits active receptor-mediated endocytosis for enhanced tumor uptake and reduced side effects. By eliminating the need for both Cremophor EL and organic solvents while simultaneously increasing antitumor efficacy, this method provides a superior alternative to currently accepted methods for PTX delivery. PMID:26715846

The Role of the Side Chain on the Performance of N-type Conjugated Polymers in Aqueous Electrolytes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giovannitti, Alexander; Maria, Iuliana P.; Hanifi, David

Here, we report a design strategy that allows the preparation of solution processable n-type materials from low boiling point solvents for organic electrochemical transistors (OECTs). The polymer backbone is based on NDI-T2 copolymers where a branched alkyl side chain is gradually exchanged for a linear ethylene glycol-based side chain. A series of random copolymers was prepared with glycol side chain percentages of 0, 10, 25, 50, 75, 90, and 100 with respect to the alkyl side chains. These were characterized to study the influence of the polar side chains on interaction with aqueous electrolytes, their electrochemical redox reactions, and performancemore » in OECTs when operated in aqueous electrolytes. We observed that glycol side chain percentages of >50% are required to achieve volumetric charging, while lower glycol chain percentages show a mixed operation with high required voltages to allow for bulk charging of the organic semiconductor. A strong dependence of the electron mobility on the fraction of glycol chains was found for copolymers based on NDI-T2, with a significant drop as alkyl side chains are replaced by glycol side chains.« less

The Role of the Side Chain on the Performance of N-type Conjugated Polymers in Aqueous Electrolytes.

PubMed

Giovannitti, Alexander; Maria, Iuliana P; Hanifi, David; Donahue, Mary J; Bryant, Daniel; Barth, Katrina J; Makdah, Beatrice E; Savva, Achilleas; Moia, Davide; Zetek, Matyáš; Barnes, Piers R F; Reid, Obadiah G; Inal, Sahika; Rumbles, Garry; Malliaras, George G; Nelson, Jenny; Rivnay, Jonathan; McCulloch, Iain

2018-05-08

We report a design strategy that allows the preparation of solution processable n-type materials from low boiling point solvents for organic electrochemical transistors (OECTs). The polymer backbone is based on NDI-T2 copolymers where a branched alkyl side chain is gradually exchanged for a linear ethylene glycol-based side chain. A series of random copolymers was prepared with glycol side chain percentages of 0, 10, 25, 50, 75, 90, and 100 with respect to the alkyl side chains. These were characterized to study the influence of the polar side chains on interaction with aqueous electrolytes, their electrochemical redox reactions, and performance in OECTs when operated in aqueous electrolytes. We observed that glycol side chain percentages of >50% are required to achieve volumetric charging, while lower glycol chain percentages show a mixed operation with high required voltages to allow for bulk charging of the organic semiconductor. A strong dependence of the electron mobility on the fraction of glycol chains was found for copolymers based on NDI-T2, with a significant drop as alkyl side chains are replaced by glycol side chains.

The Role of the Side Chain on the Performance of N-type Conjugated Polymers in Aqueous Electrolytes

DOE PAGES

Giovannitti, Alexander; Maria, Iuliana P.; Hanifi, David; ...

2018-04-24

Here, we report a design strategy that allows the preparation of solution processable n-type materials from low boiling point solvents for organic electrochemical transistors (OECTs). The polymer backbone is based on NDI-T2 copolymers where a branched alkyl side chain is gradually exchanged for a linear ethylene glycol-based side chain. A series of random copolymers was prepared with glycol side chain percentages of 0, 10, 25, 50, 75, 90, and 100 with respect to the alkyl side chains. These were characterized to study the influence of the polar side chains on interaction with aqueous electrolytes, their electrochemical redox reactions, and performancemore » in OECTs when operated in aqueous electrolytes. We observed that glycol side chain percentages of >50% are required to achieve volumetric charging, while lower glycol chain percentages show a mixed operation with high required voltages to allow for bulk charging of the organic semiconductor. A strong dependence of the electron mobility on the fraction of glycol chains was found for copolymers based on NDI-T2, with a significant drop as alkyl side chains are replaced by glycol side chains.« less

Hydrophobic potential of mean force as a solvation function for protein structure prediction.

PubMed

Lin, Matthew S; Fawzi, Nicolas Lux; Head-Gordon, Teresa

2007-06-01

We have developed a solvation function that combines a Generalized Born model for polarization of protein charge by the high dielectric solvent, with a hydrophobic potential of mean force (HPMF) as a model for hydrophobic interaction, to aid in the discrimination of native structures from other misfolded states in protein structure prediction. We find that our energy function outperforms other reported scoring functions in terms of correct native ranking for 91% of proteins and low Z scores for a variety of decoy sets, including the challenging Rosetta decoys. This work shows that the stabilizing effect of hydrophobic exposure to aqueous solvent that defines the HPMF hydration physics is an apparent improvement over solvent-accessible surface area models that penalize hydrophobic exposure. Decoys generated by thermal sampling around the native-state basin reveal a potentially important role for side-chain entropy in the future development of even more accurate free energy surfaces.

PWR steam generator chemical cleaning, Phase I. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rothstein, S.

1978-07-01

United Nuclear Industries (UNI) entered into a subcontract with Consolidated Edison Company of New York (Con Ed) on August 8, 1977, for the purpose of developing methods to chemically clean the secondary side tube to tube support crevices of the steam generators of Indian Point Nos. 1 and 2 PWR plants. This document represents the first reporting on activities performed for Phase I of this effort. Specifically, this report contains the results of a literature search performed by UNI for the purpose of determining state-of-the-art chemical solvents and methods for decontaminating nuclear reactor steam generators. The results of the searchmore » sought to accomplish two objectives: (1) identify solvents beyond those proposed at present by UNI and Con Ed for the test program, and (2) confirm the appropriateness of solvents and methods of decontamination currently in use by UNI.« less

Protein Conformational Entropy is Independent of Solvent

NASA Astrophysics Data System (ADS)

Nucci, Nathaniel; Moorman, Veronica; Gledhill, John; Valentine, Kathleen; Wand, A. Joshua

Proteins exhibit most of their conformational entropy in individual bond vector motions on the ps-ns timescale. These motions can be examined through determination of the Lipari-Szabo generalized squared order parameter (O2) using NMR spin relaxation measurements. It is often argued that most protein motions are intimately dependent on the nature of the solvating environment. Here the solvent dependence of the fast protein dynamics is directly assessed. Using the model protein ubiquitin, the order parameters of the backbone and methyl groups are shown to be generally unaffected by up to a six-fold increase in bulk viscosity or by encapsulation in the nanoscale interior of a reverse micelle. In addition, the reverse micelle condition permits direct comparison of protein dynamics to the mobility of the hydration layer; no correlation is observed. The dynamics of aromatic side chains are also assessed and provide an estimate of the length- and timescale of protein motions where solvent dependence is seen. These data demonstrate the solvent independence of conformational entropy, clarifying a long-held misconception in the fundamental behavior of biological macromolecules. Supported by the National Science Foundation.