Spatial Analysis of Stover Moisture Content During Harvest Season in the U.S.

DOE PAGES

Oyedeji, Oluwafemi A.; Sokhansanj, Shahab; Webb, Erin

2017-01-01

The moisture content of a maturing crop varies as the harvest season progresses. For crop residues such as corn stover, moisture content at the time of harvest can be as high as 75% (wet mass basis) to less than 20% depending on the geographic location (climate conditions) and stage of harvest. Biomass moisture content is critical for baling and extended storage. It is therefore essential to have an estimate of the quantities of corn stover available as wet or dry for various parts of the U.S. To this end, we analyzed hourly weather data (temperature, humidity, and rainfall) from themore » Typical Meteorological Year v.3 (TMY3) dataset developed by the National Renewable Energy Laboratory. A recently published set of equations for calculating the moisture content of stover as a function of hourly temperature, humidity, and rainfall were used. The annual start and end of corn grain harvest along with annual grain production (in bushels) for each state were extracted from USDA National Agricultural Statistics Service reports. Using these datasets and moisture sorption equations, the percentage of corn stover tonnage with moisture content less than 20%, between 20% and 40%, or greater than 40% was estimated from the length of time that the biomass was in these moisture content ranges. These calculations were carried out for several locations within each of the states for which TMY data were available. It was concluded that about 37.2% of corn stover is dry (<20% moisture content), whereas 36.5% is wet (>40% moisture content) nationwide. The remaining 27.0% of corn stover is between 20% and 40% moisture content. Keywords: Corn stover, Equilibrium moisture content, Field drying, Moisture content, Stover harvest, Typical Meteorological Year data.« less

Spatial Analysis of Stover Moisture Content During Harvest Season in the U.S.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oyedeji, Oluwafemi A.; Sokhansanj, Shahab; Webb, Erin

The moisture content of a maturing crop varies as the harvest season progresses. For crop residues such as corn stover, moisture content at the time of harvest can be as high as 75% (wet mass basis) to less than 20% depending on the geographic location (climate conditions) and stage of harvest. Biomass moisture content is critical for baling and extended storage. It is therefore essential to have an estimate of the quantities of corn stover available as wet or dry for various parts of the U.S. To this end, we analyzed hourly weather data (temperature, humidity, and rainfall) from themore » Typical Meteorological Year v.3 (TMY3) dataset developed by the National Renewable Energy Laboratory. A recently published set of equations for calculating the moisture content of stover as a function of hourly temperature, humidity, and rainfall were used. The annual start and end of corn grain harvest along with annual grain production (in bushels) for each state were extracted from USDA National Agricultural Statistics Service reports. Using these datasets and moisture sorption equations, the percentage of corn stover tonnage with moisture content less than 20%, between 20% and 40%, or greater than 40% was estimated from the length of time that the biomass was in these moisture content ranges. These calculations were carried out for several locations within each of the states for which TMY data were available. It was concluded that about 37.2% of corn stover is dry (<20% moisture content), whereas 36.5% is wet (>40% moisture content) nationwide. The remaining 27.0% of corn stover is between 20% and 40% moisture content. Keywords: Corn stover, Equilibrium moisture content, Field drying, Moisture content, Stover harvest, Typical Meteorological Year data.« less

Time domain reflectometry measured moisture content of sewage sludge compost across temperatures.

PubMed

Cai, Lu; Chen, Tong-Bin; Gao, Ding; Liu, Hong-Tao; Chen, Jun; Zheng, Guo-Di

2013-01-01

Time domain reflectometry (TDR) is a prospective measurement technology for moisture content of sewage sludge composting material; however, a significant dependence upon temperature has been observed. The objective of this study was to assess the impacts of temperature upon moisture content measurement and determine if TDR could be used to monitor moisture content in sewage sludge compost across a range of temperatures. We also investigated the combined effects of temperature and conductivity on moisture content measurement. The results revealed that the moisture content of composting material could be determined by TDR using coated probes, even when the measured material had a moisture content of 0.581 cm(3)cm(-3), temperature of 70°C and conductivity of 4.32 mS cm(-1). TDR probes were calibrated as a function of dielectric properties that included temperature effects. When the bulk temperature varied from 20°C to 70°C, composting material with 0.10-0.70 cm(3)cm(-3) moisture content could be measured by TDR using coated probes, and calibrations based on different temperatures minimized the errors. Copyright © 2012. Published by Elsevier Ltd.

Stress wave velocity and dynamic modulus of elasticity of yellow-poplar ranging from 100 to 10 percent moisture content

Treesearch

Jody D. Gray; Shawn T. Grushecky; James P. Armstrong

2008-01-01

Moisture content has a significant impact on mechanical properties of wood. In recent years, stress wave velocity has been used as an in situ and non-destructive method for determining the stiffness of wooden elements. The objective of this study was to determine what effect moisture content has on stress wave velocity and dynamic modulus of elasticity. Results...

Discrimination of soil hydraulic properties by combined thermal infrared and microwave remote sensing

NASA Technical Reports Server (NTRS)

Vandegriend, A. A.; Oneill, P. E.

1986-01-01

Using the De Vries models for thermal conductivity and heat capacity, thermal inertia was determined as a function of soil moisture for 12 classes of soil types ranging from sand to clay. A coupled heat and moisture balance model was used to describe the thermal behavior of the top soil, while microwave remote sensing was used to estimate the soil moisture content of the same top soil. Soil hydraulic parameters are found to be very highly correlated with the combination of soil moisture content and thermal inertia at the same moisture content. Therefore, a remotely sensed estimate of the thermal behavior of the soil from diurnal soil temperature observations and an independent remotely sensed estimate of soil moisture content gives the possibility of estimating soil hydraulic properties by remote sensing.

Cloud-based application for rice moisture content measurement using image processing technique and perceptron neural network

NASA Astrophysics Data System (ADS)

Cruz, Febus Reidj G.; Padilla, Dionis A.; Hortinela, Carlos C.; Bucog, Krissel C.; Sarto, Mildred C.; Sia, Nirlu Sebastian A.; Chung, Wen-Yaw

2017-02-01

This study is about the determination of moisture content of milled rice using image processing technique and perceptron neural network algorithm. The algorithm involves several inputs that produces an output which is the moisture content of the milled rice. Several types of milled rice are used in this study, namely: Jasmine, Kokuyu, 5-Star, Ifugao, Malagkit, and NFA rice. The captured images are processed using MATLAB R2013a software. There is a USB dongle connected to the router which provided internet connection for online web access. The GizDuino IOT-644 is used for handling the temperature and humidity sensor, and for sending and receiving of data from computer to the cloud storage. The result is compared to the actual moisture content range using a moisture tester for milled rice. Based on results, this study provided accurate data in determining the moisture content of the milled rice.

Moisture sorption isotherms and thermodynamic properties of bovine leather

NASA Astrophysics Data System (ADS)

Fakhfakh, Rihab; Mihoubi, Daoued; Kechaou, Nabil

2018-04-01

This study was aimed at the determination of bovine leather moisture sorption characteristics using a static gravimetric method at 30, 40, 50, 60 and 70 °C. The curves exhibit type II behaviour according to the BET classification. The sorption isotherms fitting by seven equations shows that GAB model is able to reproduce the equilibrium moisture content evolution with water activity for moisture range varying from 0.02 to 0.83 kg/kg d.b (0.9898 < R2 < 0.999). The sorption isotherms exhibit hysteresis effect. Additionally, sorption isotherms data were used to determine the thermodynamic properties such as isosteric heat of sorption, sorption entropy, spreading pressure, net integral enthalpy and entropy. Net isosteric heat of sorption and differential entropy were evaluated through direct use of moisture isotherms by applying the Clausius-Clapeyron equation and used to investigate the enthalpy-entropy compensation theory. Both sorption enthalpy and entropy for desorption increase to a maximum with increasing moisture content, and then decrease sharply with rising moisture content. Adsorption enthalpy decreases with increasing moisture content. Whereas, adsorption entropy increases smoothly with increasing moisture content to a maximum of 6.29 J/K.mol. Spreading pressure increases with rising water activity. The net integral enthalpy seemed to decrease and then increase to become asymptotic. The net integral entropy decreased with moisture content increase.

Effect of temperature and moisture content on tensile behaviour of false banana fibre (Ensete ventricosum)

NASA Astrophysics Data System (ADS)

Mizera, Cestmir; Herak, David; Hrabe, Petr; Kabutey, Abraham

2017-07-01

The mechanical behaviour of natural fibres as composite materials can be affected by changes in temperature and moisture content. The aim of this paper was to describe the effect of temperature and moisture content on tensile strength of false banana fibre (Ensete ventricosum) and to determine its water absorption. Samples of fibres were prepared and tested until rupture point with strain rate of 0.05 min-1 at temperature change between -20 and 220°C as well as moisture content between 10 and 90% wb. The water absorption and release of Ensete fibres at 60 and 90% relative humidity was also determined. Results showed that Ensete fibres exhibited stability of tensile strength in the temperature range from 0 to 100°C but the increase of temperature decreased statistically significantly the tensile strength. The effect of moisture content on tensile strength was not statistically significant. The equilibrium moisture content at 60% relative humidity and 25°C was determined.

Dielectric properties-based method for rapid and nondestructive moisture sensing in almonds

USDA-ARS?s Scientific Manuscript database

A dielectric-based method is presented for moisture determination in almonds independent of bulk density. The dielectric properties of almond were measured between 5 and 15 GHz, with a 1-GHz increments, for samples with moisture contents ranging from 4.8% to 16.5%, wet basis, bulk densities ranging ...

The technique of duff hygrometer calibration

Treesearch

T. Kachin; H. T. Gisborne

1937-01-01

The moisture content of the top layer of coniferous needles and twigs covering the forest floor is one of the factors of forest fire danger which must he determined accurately if fire danger in such timber types is to he measured. As this moisture content cannot he estimated accurately and as a difference of a few per cent of moisture, especially in the lower range,...

Hazardous gases and oxygen depletion in a wet paddy pile: an experimental study in a simulating underground rice mill pit, Thailand.

PubMed

Yenjai, Pornthip; Chaiear, Naesinee; Charerntanyarak, Lertchai; Boonmee, Mallika

2012-01-01

During the rice harvesting season in Thailand, large amounts of fresh paddy are sent to rice mills immediately after harvesting due to a lack of proper farm storage space. At certain levels of moisture content, rice grains may generate hazardous gases, which can replace oxygen (O(2)) in the confined spaces of underground rice mill pits. This phenomenon has been observed in a fatal accident in Thailand. Our study aimed to investigate the type of gases and their air concentrations emitted from the paddy piles at different levels of moisture content and duration of piling time. Four levels of moisture content in the paddy piles were investigated, including dry paddy group (< 14% wet basis (wb)), wet paddy groups (22-24, 25-27 and 28-30%wb). Our measurements were conducted in 16 experimental concrete pits 80 × 80 cm wide by 60 cm high. Gases emitted were measured with an infrared spectrophotometer and a multi-gas detector every 12 h for 5 days throughout the experiment. The results revealed high levels of carbon dioxide (CO(2)) (range 5,864-8,419 ppm) in all wet paddy groups, which gradually increased over time. The concentration of carbon monoxide (CO), methane (CH(4)), nitromethane (CH(3)NO(2)) and nitrous oxide (N(2)O) in all wet paddy groups increased with piling time and with moisture content, with ranges of 11-289; 2-8; 36-374; and 4-26 ppm, respectively. The highest levels of moisture content in the paddy piles were in the range 28-30%wb. Nitrogen dioxide (NO(2)) concentrations were low in all paddy groups. The percentage of O(2) in the wet paddy groups decreased with piling time and moisture content (from 18.7% to 4.1%). This study suggested that hazardous gases could be emitted in moist paddy piles, and their concentrations could increase with increasing moisture content and piling time period.

Effects of moisture content on wind erosion thresholds of biochar

NASA Astrophysics Data System (ADS)

Silva, F. C.; Borrego, C.; Keizer, J. J.; Amorim, J. H.; Verheijen, F. G. A.

2015-12-01

Biochar, i.e. pyrolysed biomass, as a soil conditioner is gaining increasing attention in research and industry, with guidelines and certifications being developed for biochar production, storage and handling, as well as for application to soils. Adding water to biochar aims to reduce its susceptibility to become air-borne during and after the application to soils, thereby preventing, amongst others, human health issues from inhalation. The Bagnold model has previously been modified to explain the threshold friction velocity of coal particles at different moisture contents, by adding an adhesive effect. However, it is unknown if this model also works for biochar particles. We measured the threshold friction velocities of a range of biochar particles (woody feedstock) under a range of moisture contents by using a wind tunnel, and tested the performance of the modified Bagnold model. Results showed that the threshold friction velocity can be significantly increased by keeping the gravimetric moisture content at or above 15% to promote adhesive effects between the small particles. For the specific biochar of this study, the modified Bagnold model accurately estimated threshold friction velocities of biochar particles up to moisture contents of 10%.

Analysis of Moisture Content in Beetroot using Fourier Transform Infrared Spectroscopy and by Principal Component Analysis.

PubMed

Nesakumar, Noel; Baskar, Chanthini; Kesavan, Srinivasan; Rayappan, John Bosco Balaguru; Alwarappan, Subbiah

2018-05-22

The moisture content of beetroot varies during long-term cold storage. In this work, we propose a strategy to identify the moisture content and age of beetroot using principal component analysis coupled Fourier transform infrared spectroscopy (FTIR). Frequent FTIR measurements were recorded directly from the beetroot sample surface over a period of 34 days for analysing its moisture content employing attenuated total reflectance in the spectral ranges of 2614-4000 and 1465-1853 cm -1 with a spectral resolution of 8 cm -1 . In order to estimate the transmittance peak height (T p ) and area under the transmittance curve [Formula: see text] over the spectral ranges of 2614-4000 and 1465-1853 cm -1 , Gaussian curve fitting algorithm was performed on FTIR data. Principal component and nonlinear regression analyses were utilized for FTIR data analysis. Score plot over the ranges of 2614-4000 and 1465-1853 cm -1 allowed beetroot quality discrimination. Beetroot quality predictive models were developed by employing biphasic dose response function. Validation experiment results confirmed that the accuracy of the beetroot quality predictive model reached 97.5%. This research work proves that FTIR spectroscopy in combination with principal component analysis and beetroot quality predictive models could serve as an effective tool for discriminating moisture content in fresh, half and completely spoiled stages of beetroot samples and for providing status alerts.

Design, development and method validation of a novel multi-resonance microwave sensor for moisture measurement.

PubMed

Peters, Johanna; Taute, Wolfgang; Bartscher, Kathrin; Döscher, Claas; Höft, Michael; Knöchel, Reinhard; Breitkreutz, Jörg

2017-04-08

Microwave sensor systems using resonance technology at a single resonance in the range of 2-3 GHz have been shown to be a rapid and reliable tool for moisture determination in solid materials including pharmaceutical granules. So far, their application is limited to lower moisture ranges or limitations above certain moisture contents had to be accepted. Aim of the present study was to develop a novel multi-resonance sensor system in order to expand the measurement range. Therefore, a novel sensor using additional resonances over a wide frequency band was designed and used to investigate inherent limitations of first generation sensor systems and material-related limits. Using granule samples with different moisture contents, an experimental protocol for calibration and validation of the method was established. Pursuant to this protocol, a multiple linear regression (MLR) prediction model built by correlating microwave moisture values to the moisture determined by Karl Fischer titration was chosen and rated using conventional criteria such as coefficient of determination (R 2 ) and root mean square error of calibration (RMSEC). Using different operators, different analysis dates and different ambient conditions the method was fully validated following the guidance of ICH Q2(R1). The study clearly showed explanations for measurement uncertainties of first generation sensor systems which confirmed the approach to overcome these by using additional resonances. The established prediction model could be validated in the range of 7.6-19.6%, demonstrating its fit for its future purpose, the moisture content determination during wet granulations. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of Moisture Content on Thermal Properties of Porous Building Materials

NASA Astrophysics Data System (ADS)

Kočí, Václav; Vejmelková, Eva; Čáchová, Monika; Koňáková, Dana; Keppert, Martin; Maděra, Jiří; Černý, Robert

2017-02-01

The thermal conductivity and specific heat capacity of characteristic types of porous building materials are determined in the whole range of moisture content from dry to fully water-saturated state. A transient pulse technique is used in the experiments, in order to avoid the influence of moisture transport on measured data. The investigated specimens include cement composites, ceramics, plasters, and thermal insulation boards. The effect of moisture-induced changes in thermal conductivity and specific heat capacity on the energy performance of selected building envelopes containing the studied materials is then analyzed using computational modeling of coupled heat and moisture transport. The results show an increased moisture content as a substantial negative factor affecting both thermal properties of materials and energy balance of envelopes, which underlines the necessity to use moisture-dependent thermal parameters of building materials in energy-related calculations.

Geological and engineering analysis of residual soil for forewarning landslide from highland area in northern Thailand

NASA Astrophysics Data System (ADS)

Thongkhao, Thanakrit; Phantuwongraj, Sumet; Choowong, Montri; Thitimakorn, Thanop; Charusiri, Punya

2015-11-01

One devastating landslide event in northern Thailand occurred in 2006 at Ban Nong Pla village, Chiang Klang highland of Nan province after, a massive amount of residual soil moved from upstream to downstream, via creek tributaries, into a main stream after five days of unusual heavy rainfall. In this paper, the geological and engineering properties of residual soil derived fromsedimentary rocks were analyzed and integrated. Geological mapping, electrical resistivity survey and test pits were carried out along three transect lines together with systematic collection of undisturbed and disturbed residual soil samples. As a result, the average moisture content in soil is 24.83% with average specific gravity of 2.68,whereas the liquid limit is 44.93%, plastic limit is 29.35% and plastic index is 15.58%. The cohesion of soil ranges between 0.096- 1.196 ksc and the angle of internal friction is between 11.51 and 35.78 degrees. This suggests that the toughness properties of soil change when moisture content increases. Results from electrical resistivity survey reveal that soil thicknesses above the bedrock along three transects range from 2 to 9 m. The soil shear strength reach the rate of high decreases in the range of 72 to 95.6% for residual soil from shale, siltstone and sandstone, respectively. Strength of soil decreaseswhen the moisture content in soil increases. Shear strength also decreases when the moisture content changes. Therefore, the natural soil slope in the study area will be stable when the moisture content in soil level is equal to one, but when the moisture content between soil particle increases, strength of soil will decrease resulting in soil strength decreasing.

Microwave remote sensing of soil moisture content over bare and vegetated fields

NASA Technical Reports Server (NTRS)

Wang, J. R.; Shiue, J. C.; Mcmurtrey, J. E., III

1980-01-01

Remote measurements of soil moisture contents over bare fields and fields covered with orchard grass, corn, and soybean were made during October 1979 with 1.4 GHz and 5 GHz microwave radiometers mounted on a truck. Ground truth of soil moisture content, ambient air, and soil temperatures was acquired concurrently with the radiometric measurements. The biomass of the vegetation was sampled about once a week. The measured brightness temperatures over bare fields were compared with those of radiative transfer model calculations using as inputs the acquired soil moisture and temperature data with appropriate values of dielectric constants for soil-water mixtures. Good agreement was found between the calculated and the measured results over 10-70 deg incident angles. The presence of vegetation was found to reduce the sensitivity of soil moisture sensing. At 1.4 GHz the sensitivity reduction ranged from approximately 20% for 10-cm tall grassland to over 60% for the dense soybean field. At 5 GHz the corresponding reduction in sensitivity ranged from approximately 70 to approximately 90%.

Correlation between near infrared spectroscopy and electrical techniques in measuring skin moisture content

NASA Astrophysics Data System (ADS)

Mohamad, M.; Sabbri, A. R. M.; Mat Jafri, M. Z.; Omar, A. F.

2014-11-01

Near infrared (NIR) spectroscopy technique serves as an important tool for the measurement of moisture content of skin owing to the advantages it has over the other techniques. The purpose of the study is to develop a correlation between NIR spectrometer with electrical conventional techniques for skin moisture measurement. A non-invasive measurement of moisture content of skin was performed on different part of human face and hand under control environment (temperature 21 ± 1 °C, relative humidity 45 ± 5 %). Ten healthy volunteers age between 21-25 (male and female) participated in this study. The moisture content of skin was measured using DermaLab® USB Moisture Module, Scalar Moisture Checker and NIR spectroscopy (NIRQuest). Higher correlation was observed between NIRQuest and Dermalab moisture probe with a coefficient of determination (R2) above 70 % for all the subjects. However, the value of R2 between NIRQuest and Moisture Checker was observed to be lower with the R2 values ranges from 51.6 to 94.4 %. The correlation of NIR spectroscopy technique successfully developed for measuring moisture content of the skin. The analysis of this correlation can help to establish novel instruments based on an optical system in clinical used especially in the dermatology field.

Influence of moisture content on inactivation of Escherichia coli O157:H7 and Salmonella enterica serovar Typhimurium in powdered red and black pepper spices by radio-frequency heating.

PubMed

Jeong, Seul-Gi; Kang, Dong-Hyun

2014-04-17

The influence of moisture content during radio-frequency (RF) heating on heating rate, dielectric properties, and inactivation of foodborne pathogens was investigated. The effect of RF heating on the quality of powdered red and black pepper spices with different moisture ranges was also investigated. Red pepper (12.6%, 15.2%, 19.1%, and 23.3% dry basis, db) and black pepper (10.1%, 17.2%, 23.7%, and 30.5% db) inoculated with Escherichia coli O157:H7 and Salmonella enterica serovar Typhimurium were treated in a RF heating system with 27.12 MHz. The heating rate of the sample was dependent on moisture content up to 19.1% (db) of red pepper and 17.2% (db) of black pepper, but there was a significant decrease in the heating rate when the moisture content was increased beyond these levels. The dielectric properties of both samples increased with a rise in moisture content. As the moisture content increased, treatment time required to reduce E. coli O157:H7 and S. Typhimurium by more than 7 log CFU/g (below the detection limit, 1 log CFU/g) decreased and then increased again without affecting product quality when the moisture content exceeded a level corresponding to the peak heating rate. RF treatment significantly (P<0.05) reduced moisture content of both spices. These results suggest that RF heating can be effectively used to not only control pathogens but also reduce moisture levels in spices and that the effect of inactivation is dependent on moisture content. Copyright © 2014 Elsevier B.V. All rights reserved.

Experimental study of the moisture distribution on the wetting front during drainage and imbibition in a 2D sand chamber

NASA Astrophysics Data System (ADS)

Wei, Yunbo; Chen, Kouping; Wu, Jichun; Zhu, Xiaobin

2018-06-01

In the present study, the moisture distribution on the wetting front during drainage and imbibition in a 2D sand chamber is studied thoroughly. Based on the high-resolution data measured by light transmission method, the moisture distribution is observed and then analyzed quantitatively. During drainage and imbibition, different moisture distributions are observed: (a) during drainage, moisture contents fluctuate in a larger range and fingers can be seen on the wetting front; (b) while during imbibition, moisture contents fluctuate in a smaller range and the wetting front is more regular. The Hurst coefficients are successful in capturing different characteristics of the moisture distribution between drainage and imbibition. During imbibition, the Hurst coefficients are around 0.2 on the wetting front; while during drainage, the Hurst coefficients are around 0.5. As the porosity changes from 0.336 to 0.383, the moisture distribution in the sand chamber does not display obvious change. While as the imbibition rate increases from 5 ml/min to 400 ml/min, the moisture distribution on the wetting front becomes more uniform.

[The evaluation of the error of the thermal pulse technique used to measure moisture content of root substrates in space greenhouse

NASA Technical Reports Server (NTRS)

Podol'skii, I. G.; Norokh, A. A.; Bingham, G. E.; Brigham, G. E. (Principal Investigator); Campbell, W. F. (Principal Investigator)

2002-01-01

Point thermopulse probes were used to monitor moisture level in the root substrates during cultivation of higher plants in a space greenhouse. Investigated were performance data of the thermopulse moisture probe in integration with the space greenhouse. It was shown that within the substrate moisture range from 20 up to 100% of the full saturation the technique error does not exceed 1.5%. The thermopulse technique bears much promise for metrologic monitoring of the root substrate moisture content in space greenhouses no matter water and air supply technology.

Practical Considerations of Moisture in Baled Biomass Feedstocks

DOE Office of Scientific and Technical Information (OSTI.GOV)

William A. Smith; Ian J. Bonner; Kevin L. Kenney

2013-01-01

Agricultural residues make up a large portion of the immediately available biomass feedstock for renewable energy markets. Current collection and storage methods rely on existing feed and forage practices designed to preserve nutrients and properties of digestibility. Low-cost collection and storage practices that preserve carbohydrates across a range of inbound moisture contents are needed to assure the economic and technical success of the emerging biomass industry. This study examines the movement of moisture in storage and identifies patterns of migration resulting from several on-farm storage systems and their impacts on moisture measurement and dry matter recovery. Baled corn stover andmore » energy sorghum were stored outdoors in uncovered, tarp-covered, or wrapped stacks and sampled periodically to measure moisture and dry matter losses. Interpolation between discrete sampling locations in the stack improved bulk moisture content estimates and showed clear patterns of accumulation and re-deposition. Atmospheric exposure, orientation, and contact with barriers (i.e., soil, tarp, and wrap surfaces) were found to cause the greatest amount of moisture heterogeneity within stacks. Although the bulk moisture content of many stacks remained in the range suitable for aerobic stability, regions of high moisture were sufficient to support microbial activity, thus support dry matter loss. Stack configuration, orientation, and coverage methods are discussed relative to impact on moisture management and dry matter preservation. Additionally, sample collection and data analysis are discussed relative to assessment at the biorefinery as it pertains to stability in storage, queuing, and moisture carried into processing.« less

Effect of process variables on the density and durability of the pellets made from high moisture corn stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaya Shankar Tumuluru

2014-03-01

A flat die pellet mill was used to understand the effect of high levels of feedstock moisture content in the range of 28–38% (w.b.), with die rotational speeds of 40–60 Hz, and preheating temperatures of 30–110 °C on the pelleting characteristics of 4.8 mm screen size ground corn stover using an 8 mm pellet die. The physical properties of the pelletised biomass studied are: (a) pellet moisture content, (b) unit, bulk and tapped density, and (c) durability. Pelletisation experiments were conducted based on central composite design. Analysis of variance (ANOVA) indicated that feedstock moisture content influenced all of the physicalmore » properties at P < 0.001. Pellet moisture content decreased with increase in preheating temperature to about 110 °C and decreasing the feedstock moisture content to about 28% (w.b.). Response surface models developed for quality attributes with respect to process variables has adequately described the process with coefficient of determination (R2) values of >0.88. The other pellet quality attributes such as unit, bulk, tapped density, were maximised at feedstock moisture content of 30–33% (w.b.), die speeds of >50 Hz and preheating temperature of >90 °C. In case of durability a medium moisture content of 33–34% (w.b.) and preheating temperatures of >70 °C and higher die speeds >50 Hz resulted in high durable pellets. It can be concluded from the present study that feedstock moisture content, followed by preheating, and die rotational speed are the interacting process variables influencing pellet moisture content, unit, bulk and tapped density and durability.« less

Soil moisture datasets at five sites in the central Sierra Nevada and northern Coast Ranges, California

USGS Publications Warehouse

Stern, Michelle A.; Anderson, Frank A.; Flint, Lorraine E.; Flint, Alan L.

2018-05-03

In situ soil moisture datasets are important inputs used to calibrate and validate watershed, regional, or statewide modeled and satellite-based soil moisture estimates. The soil moisture dataset presented in this report includes hourly time series of the following: soil temperature, volumetric water content, water potential, and total soil water content. Data were collected by the U.S. Geological Survey at five locations in California: three sites in the central Sierra Nevada and two sites in the northern Coast Ranges. This report provides a description of each of the study areas, procedures and equipment used, processing steps, and time series data from each site in the form of comma-separated values (.csv) tables.

Capacitance Based Moisture Sensing for Microgravity Plant Modules: Sensor Design and Considerations

NASA Technical Reports Server (NTRS)

Schaber, Chad L.; Nurge, Mark; Monje, Oscar

2011-01-01

Life support systems for growing plants in microgravity should strive for providing optimal growing conditions and increased automation. Accurately tracking soil moisture content can forward both of these aims, so an attempt was made to instrument a microgravity growth module currently in development, the VEGGIE rooting pillow, in order to monitor moisture levels. Two electrode systems for a capacitance-based moisture sensor were tested. Trials with both types of electrodes showed a linear correlation between observed capacitance and water content over certain ranges of moisture within the pillows. Overall, both types of the electrodes and the capacitance-based moisture sensor are promising candidates for tracking water levels for microgravity plant growth systems.

Hyperspectral Reflectance Imaging Technique for Visualization of Moisture Distribution in Cooked Chicken Breast

PubMed Central

Kandpal, Lalit Mohan; Lee, Hoonsoo; Kim, Moon S.; Mo, Changyeun; Cho, Byoung-Kwan

2013-01-01

Spectroscopy has proven to be an efficient tool for measuring the properties of meat. In this article, hyperspectral imaging (HSI) techniques are used to determine the moisture content in cooked chicken breast over the VIS/NIR (400–1,000 nm) spectral range. Moisture measurements were performed using an oven drying method. A partial least squares regression (PLSR) model was developed to extract a relationship between the HSI spectra and the moisture content. In the full wavelength range, the PLSR model possessed a maximum R2p of 0.90 and an SEP of 0.74%. For the NIR range, the PLSR model yielded an R2p of 0.94 and an SEP of 0.71%. The majority of the absorption peaks occurred around 760 and 970 nm, representing the water content in the samples. Finally, PLSR images were constructed to visualize the dehydration and water distribution within different sample regions. The high correlation coefficient and low prediction error from the PLSR analysis validates that HSI is an effective tool for visualizing the chemical properties of meat. PMID:24084119

Physicochemical Changes and Resistant-Starch Content of Extruded Cornstarch with and without Storage at Refrigerator Temperatures.

PubMed

Neder-Suárez, David; Amaya-Guerra, Carlos A; Quintero-Ramos, Armando; Pérez-Carrillo, Esther; Alanís-Guzmán, María G de J; Báez-González, Juan G; García-Díaz, Carlos L; Núñez-González, María A; Lardizábal-Gutiérrez, Daniel; Jiménez-Castro, Jorge A

2016-08-15

Effects of extrusion cooking and low-temperature storage on the physicochemical changes and resistant starch (RS) content in cornstarch were evaluated. The cornstarch was conditioned at 20%-40% moisture contents and extruded in the range 90-130 °C and at screw speeds in the range 200-360 rpm. The extrudates were stored at 4 °C for 120 h and then at room temperature. The water absorption, solubility index, RS content, viscoelastic, thermal, and microstructural properties of the extrudates were evaluated before and after storage. The extrusion temperature and moisture content significantly affected the physicochemical properties of the extrudates before and after storage. The RS content increased with increasing moisture content and extrusion temperature, and the viscoelastic and thermal properties showed related behaviors. Microscopic analysis showed that extrusion cooking damaged the native starch structure, producing gelatinization and retrogradation and forming RS. The starch containing 35% moisture and extruded at 120 °C and 320 rpm produced the most RS (1.13 g/100 g) after to storage at low temperature. Although the RS formation was low, the results suggest that extrusion cooking could be advantageous for RS production and application in the food industry since it is a pollution less, continuous process requiring only a short residence time.

Optical transparency of paper as a function of moisture content with applications to moisture measurement.

PubMed

Forughi, A F; Green, S I; Stoeber, B

2016-02-01

Accurate measurement of the moisture content of paper is essential in papermaking and is also important in some paper-based microfluidic devices. Traditional measurement techniques provide very limited spatiotemporal resolution and working range. This article presents a novel method for moisture content measurement whose operating principle is the strong correlation between the optical transparency of paper and its moisture content. Spectrographic and microscopic measurement techniques were employed to characterize the relation of moisture content and relative transparency of four types of paper: hardwood chemi-thermomechanical pulp paper, Northern bleached softwood kraft paper, unbleached softwood kraft paper, and General Electric(®) Whatman™ grade 1 chromatography paper. It was found that for all paper types, the paper transparency increased monotonically with the moisture content (as the ratio of the mass-of-water to the mass-of-dry-paper increased from 0% to 120%). This significant increase in relative transparency occurred due to the refractive index matching role of water in wet paper. It is further shown that mechanical loading of the paper has little impact on the relative transparency, for loadings that would be typical on a paper machine. The results of two transient water absorption experiments are presented that show the utility and accuracy of the technique.

Near-infrared reflectance models for the rapid prediction of quality of brewing raw materials.

PubMed

Marte, Luisa; Belloni, Paolo; Genorini, Emiliano; Sileoni, Valeria; Perretti, Giuseppe; Montanari, Luigi; Marconi, Ombretta

2009-01-28

Calibration models for quickly and reliably predicting moisture content and total nitrogen, both "as is" and "dry matter" on malt, as well as moisture content and total lipids, both "as is" and "dry matter", on maize by means of near-infrared (NIR) spectroscopy were developed. The FT-NIR spectra recorded on the finely ground cereals were correlated to the analytical data by means of the multivariate PLS algorithm. In particular, these models were developed on the raw materials, which are used by the main Italian brewing industries. Validation was carried out both by means of cross-validation and test set validation. Regression coefficients (R(2)) were higher than 97 for both malt and maize moisture content and higher than 85 and 88 for malt total nitrogen and maize total lipids, respectively. The RMSE values (both RMSECV and RMSEP) were lower than 0.1% m/m for both malt and maize moisture contents, whereas they ranged from 0.024 to 0.042% m/m for malt total nitrogen and from 0.042 to 0.055% m/m for maize total lipids. Repeatability was tested by taking into account more than one sample for each calibration and compared, when possible, to those of the standard methods. Repeatability (r(95)) ranged from 0.060 to 0.158% m/m and from 0.020 to 0.055% m/m for malt moisture and total nitrogen contents, respectively, and from 0.094 to 0.160% m/m and from 0.076 to 0.208% m/m for maize moisture and total lipids contents, respectively.

OPTIMIZING SYNTHESIS GAS YIELD FROM THE CROSS ...

EPA Pesticide Factsheets

Symposium Paper Biomass can be gasified to yield synthesis gas, tars, and ash. The process is governed by a number of parameters such as the temperature of the gasifying medium (in this case), and the moisture content of the feedstock. Synthesis gas from gasifying wood pellets was collected and analyzed as a function of inlet air temperature and feedstock moisture content. The air was introduced at temperatures ranging from 630 to 730 °C and the moisture content of the feedstock ranged from 8 to 20%. The data collected was used to establish the relationship between the outcome of gasification and these two parameters, and then to determine optimal operating parameters for maximizing the fuel value (maximizing the concentrations of flammable gases in the synthesis gas) while minimizing the production of gasification tars.

Soil moisture dynamics and smoldering combustion limits of pocosin soils in North Carolina, USA

Treesearch

James Reardon; Gary Curcio; Roberta Bartlette

2009-01-01

Smoldering combustion of wetland organic soils in the south-eastern USA is a serious management concern. Previous studies have reported smoldering was sensitive to a wide range of moisture contents, but studies of soil moisture dynamics and changing smoldering combustion potential in wetland communities are limited. Linking soil moisture measurements with estimates of...

Moisture meter calibrations for untreated and ACQ-treated southern yellow pine lumber and plywood

Treesearch

C.R. Boardman; Samuel V. Glass; Charles G. Carll

2011-01-01

This study investigates the effects of alkaline copper quaternary (ACQ) preservative treatment and of plywood glue lines on resistance-based moisture content (MC) measurements. Moisture meter readings using stainless steel screws as electrodes were acquired over a range of moisture conditions in Southern Yellow Pine (SYP) lumber and plywood. Calibration equations are...

Assessing Live Fuel Moisture For Fire Management Applications

Treesearch

David R. Weise; Roberta A. Hartford; Larry Mahaffey

1998-01-01

The variation associated with sampling live fuel moisture was examined for several shrub and canopy fuels in southern California, Arizona, and Colorado. Ninety-five % confidence intervals ranged from 5 to % . Estimated sample sizes varied greatly. The value of knowing the live fuel moisture content in fire decision making is unknown. If the fuel moisture is highly...

[Response processes of Aralia elata photosynthesis and transpiration to light and soil moisture].

PubMed

Chen, Jian; Zhang, Guang-Can; Zhang, Shu-Yong; Wang, Meng-Jun

2008-06-01

By using CIRAS-2 portable photosynthesis system, the light response processes of Aralia elata photosynthesis and transpiration under different soil moisture conditions were studied, aimed to understand the adaptability of A. elata to different light and soil moisture conditions. The results showed that the response processes of A. elata net photosynthetic rate (Pn), transpiration rate (Tr), and water use efficiency (WUE) to photon flux density (PFD) were different. With the increasing PFD in the range of 800-1800 micromol x m2(-2) x s(-1), Pn changed less, Tr decreased gradually, while WUE increased obviously. The light saturation point (LSP) and light compensation point (LCP) were about 800 and 30 micromol m(-2) x s(-1), respectively, and less affected by soil water content; while the apparent photosynthetic quantum yield (Phi) and dark respiratory rate (Rd) were more affected by the moisture content. The Pn and WUE had evident threshold responses to the variations of soil water content. When the soil relative water content (RWC) was in the range of 44%-79%, A. elata could have higher levels of Pn and WUE.

Moisture content of southern pine as related to thrust, torque, and chip formation in boring

Treesearch

C. W. McMillin; G. E. Woodson

1972-01-01

Holes 3-1/2 inches deep were bored with a 1-inch spur machine bit in southern pine having specific gravity of 0.53 (ovendry weight and volume at 10.4 percent moisture). The bit was rotated at 2,400 rpm and removed chips 0.020 inch thick. For wood moisture contents ranging from ovendry to saturation, thrust was lower when boring along the grain (average 98 pounds) than...

A semi-mechanistic model of dead fine fuel moisture for Temperate and Mediterranean ecosystems

NASA Astrophysics Data System (ADS)

Resco de Dios, Víctor; Fellows, Aaron; Boer, Matthias; Bradstock, Ross; Nolan, Rachel; Goulden, Michel

2014-05-01

Fire is a major disturbance in terrestrial ecosystems globally. It has an enormous economic and social cost, and leads to fatalities in the worst cases. The moisture content of the vegetation (fuel moisture) is one of the main determinants of fire risk. Predicting the moisture content of dead and fine fuel (< 2.5 cm in diameter) is particularly important, as this is often the most important component of the fuel complex for fire propagation. A variety of drought indices, empirical and mechanistic models have been proposed to model fuel moisture. A commonality across these different approaches is that they have been neither validated across large temporal datasets nor validated across broadly different vegetation types. Here, we present the results of a study performed at 6 locations in California, USA (5 sites) and New South Wales, Australia (1 site), where 10-hours fuel moisture content was continuously measured every 30 minutes during one full year at each site. We observed that drought indices did not accurately predict fuel moisture, and that empirical and mechanistic models both needed site-specific calibrations, which hinders their global application as indices of fuel moisture. We developed a novel, single equation and semi-mechanistic model, based on atmospheric vapor-pressure deficit. Across sites and years, mean absolute error (MAE) of predicted fuel moisture was 4.7%. MAE dropped <1% in the critical range of fuel moisture <10%. The high simplicity, accuracy and precision of our model makes it suitable for a wide range of applications: from operational purposes, to global vegetation models.

Foliar moisture content of Pacific Northwest vegetation and its relation to wildland fire behavior.

Treesearch

James K. Agee; Clinton S. Wright; Nathan Williamson; Mark H. Huff

2002-01-01

Fotiar moisture was monitored for five conifers and associated understory vegetation in Pacific Northwest forests. Decline in foliar moisture of new foliage occurred over the dry season, while less variation was evident in older foliage. Late season foliar moisture ranged from 130 to 170%. In riparian-upland comparisons, largest differences were found for understory...

The Mechanical Properties of Wood of Different Moisture Content Within -200 Degrees to +200 Degrees C Temperature Range

NASA Technical Reports Server (NTRS)

Kollmann, Franz

1941-01-01

Systematic experiments were undertaken with special reference to the effect of gross specific weight (specific weight inclusive of pores) and the moisture content of wood. It was found that the modules of elasticity of wood at room temperature and frozen at -8 degrees is practically the same. The effect of moisture on the compression strength of frozen wood was explored as well as the flexural and impact strength of frozen wood and frozen laminated wood.

Optimization of chip size and moisture content to obtain high, combined sugar recovery after sulfur dioxide-catalyzed steam pretreatment of softwood and enzymatic hydrolysis of the cellulosic component.

PubMed

Olsen, Colin; Arantes, Valdeir; Saddler, Jack

2015-01-01

The influence of chip size and moisture content on the combined sugar recovery after steam pretreatment of lodgepole pine and subsequent enzymatic hydrolysis of the cellulosic component were investigated using response surface methodology. Chip size had little influence on sugar recovery after both steam pretreatment and enzymatic hydrolysis. In contrast, the moisture of the chips greatly influenced the relative severity of steam pretreatment and, as a result, the combined sugar recovery from the hemicellulosic and cellulosic fractions. Irrespective of chip size and the pretreatment temperature, time, and SO2 loading that were used, the relative severity of pretreatment was highest at a moisture of 30-40w/w%. However, the predictive model indicated that an elevated moisture content of roughly 50w/w% (about the moisture content of a standard softwood mill chip) would result in the highest, combined sugar recovery (80%) over the widest range of steam pretreatment conditions. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effect of moisture on the methane adsorption capacity of shales: A study case in the eastern Qaidam Basin in China

NASA Astrophysics Data System (ADS)

Wang, Lu; Yu, Qingchun

2016-11-01

This study investigated the effects of moisture on high-pressure methane adsorption in carboniferous shales from the Qaidam Basin, China. The shale characteristics, including the organic/inorganic compositions and pore structure (volume and surface) distribution, were obtained using various techniques. Gibbs adsorption measurements were performed over a pressure range up to 6 MPa and temperatures of 308.15 K on dry samples and moisture-equilibrated samples to analyze the correlations between organic/inorganic matter, pore structure, and moisture content on the methane sorption capacity. Compared to dry samples, the sorption capacity of wet samples (0.44-2.52% of water content) is reduced from 19.7 ± 5.3% to 36.1% ± 6.1%. Langmuir fitting is conducted to investigate moisture-dependent variations of adsorbed methane density, Langmuir pressure, and volume. By combining the pore volume and surface distribution analyses, our observations suggested that the main competition sites for CH4-H2O covered pores of approximately 2-7 nm, whereas the effective sites for methane and water were predominantly distributed within smaller (<4 nm) and larger pores (>10 nm), respectively. Regarding the compositional correlations, the impact of moisture on the amount of adsorbed methane shows a roughly linearly decreasing trend with increasing TOC content ranging from 0.62 to 2.88%, whereas the correlation between the moisture effect and various inorganic components is more complicated. Further fitting results indicate that illite/smectite mixed formations are closely related to the methane capacity, whereas the illite content show an evident connection to the pore structural (volume and surface) variations in the presence of moisture.

Use of a region of the visible and near infrared spectrum to predict mechanical properties of wet wood and standing trees

DOEpatents

Meglen, Robert R.; Kelley, Stephen S.

2003-01-01

In a method for determining the dry mechanical strength for a green wood, the improvement comprising: (a) illuminating a surface of the wood to be determined with a reduced range of wavelengths in the VIS-NIR spectra 400 to 1150 nm, said wood having a green moisture content; (b) analyzing the surface of the wood using a spectrometric method, the method generating a first spectral data of a reduced range of wavelengths in VIS-NIR spectra; and (c) using a multivariate analysis technique to predict the mechanical strength of green wood when dry by comparing the first spectral data with a calibration model, the calibration model comprising a second spectrometric method of spectral data of a reduced range of wavelengths in VIS-NIR spectra obtained from a reference wood having a green moisture content, the second spectral being correlated with a known mechanical strength analytical result obtained from the reference wood when dried and a having a dry moisture content.

STUDIES ON THE USE OF MUTAGENIC AGENTS IN PLANT BREEDING. I. THE EFFECT OF SEED MOISTURE CONTENT ON SENSITIVITY TO X RAYS IN LUPINUS ANGUSTIFOLIUS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Francis, C.M.; Gladstones, J.S.

1963-01-01

Seeds of Lupinus angustifolius were exposed to doses of to 18.1% (fresh wt). X/sub 1/ plant damage was measured in terms of reduction in height at 110 days from sowing, delay in flowering, and reduction in mean seed yield per plant. The three measures were found to be highly correlated. Survival was not significantly affected within the range of treatments used. Radiosensitivity increased progressively with decreasing moisture contents below 11.6%, seeds with 8.1-7.6% being four to five times as sensitive as those with 11.6-16% moisture content. The latter range represented a plateau of min sensitivity. Between 18.0 and 18.1% moisture,more » sensitivity again increased. Flowering time was the most sensitive measure of plant damage in that it was the only one to register consistently an effect due to the lowest x-ray dose (2.5 kr). This indicates that flowering time could be the most reliable, for comparative purposes, of the indices used. In addition it has the important advantage of being quickly and accurately scored. The magnitude of the protection against x-ray damage afforded by increased seed moisture can be expressed quantitatively in terms of a dose reduction factor (DRF), i.e., the factor by which the dose tolerated by the most sensitive seeds is less than that required to cause the same level of damage in the most tolerant seeds. DRF (in the present experiments between four and five for all three indices of x-ray damage) represents the damage caused to the seeds by 5 kr at 6-7% moisture as being approximates the same as that caused by 20 kr at 11-16% seed moisture. This is similar to the factor of about four previously found for barley seedling height and survival, but differs from the value of 10 found for seedling leaf span and survival in tomato. It is possible, however, that the extremely low moisture contents obtained in tomato seeds (as low as 1.2%) contributed to the difference, and that greater DRF might have been found for barley and lupins had lower min seed moisture contents been obtained. It is proposed that in subsequent generations, a corresponding DRF be derived for mutation rates. This should show whether or not the protective effect of moisture against plant damage in the X/sub 1/ is paralleled by a similar protection against mutation. If it is not, as appears to be the case in barley, it should be possible to define a particular range of seed moisture contents at which the highest mutation rates can be obtained. (BBB)« less

Dielectric properties of almond kernels associated with radio frequency and microwave pasteurization

NASA Astrophysics Data System (ADS)

Li, Rui; Zhang, Shuang; Kou, Xiaoxi; Ling, Bo; Wang, Shaojin

2017-02-01

To develop advanced pasteurization treatments based on radio frequency (RF) or microwave (MW) energy, dielectric properties of almond kernels were measured by using an open-ended coaxial-line probe and impedance analyzer at frequencies between 10 and 3000 MHz, moisture contents between 4.2% to 19.6% w.b. and temperatures between 20 and 90 °C. The results showed that both dielectric constant and loss factor of the almond kernels decreased sharply with increasing frequency over the RF range (10-300 MHz), but gradually over the measured MW range (300-3000 MHz). Both dielectric constant and loss factor of almond kernels increased with increasing temperature and moisture content, and largely enhanced at higher temperature and moisture levels. Quadratic polynomial equations were developed to best fit the relationship between dielectric constant or loss factor at 27, 40, 915 or 2450 MHz and sample temperature/moisture content with R2 greater than 0.967. Penetration depth of electromagnetic wave into samples decreased with increasing frequency (27-2450 MHz), moisture content (4.2-19.6% w.b.) and temperature (20-90 °C). The temperature profiles of RF heated almond kernels under three moisture levels were made using experiment and computer simulation based on measured dielectric properties. Based on the result of this study, RF treatment has potential to be practically used for pasteurization of almond kernels with acceptable heating uniformity.

Dielectric properties of almond kernels associated with radio frequency and microwave pasteurization.

PubMed

Li, Rui; Zhang, Shuang; Kou, Xiaoxi; Ling, Bo; Wang, Shaojin

2017-02-10

To develop advanced pasteurization treatments based on radio frequency (RF) or microwave (MW) energy, dielectric properties of almond kernels were measured by using an open-ended coaxial-line probe and impedance analyzer at frequencies between 10 and 3000 MHz, moisture contents between 4.2% to 19.6% w.b. and temperatures between 20 and 90 °C. The results showed that both dielectric constant and loss factor of the almond kernels decreased sharply with increasing frequency over the RF range (10-300 MHz), but gradually over the measured MW range (300-3000 MHz). Both dielectric constant and loss factor of almond kernels increased with increasing temperature and moisture content, and largely enhanced at higher temperature and moisture levels. Quadratic polynomial equations were developed to best fit the relationship between dielectric constant or loss factor at 27, 40, 915 or 2450 MHz and sample temperature/moisture content with R 2 greater than 0.967. Penetration depth of electromagnetic wave into samples decreased with increasing frequency (27-2450 MHz), moisture content (4.2-19.6% w.b.) and temperature (20-90 °C). The temperature profiles of RF heated almond kernels under three moisture levels were made using experiment and computer simulation based on measured dielectric properties. Based on the result of this study, RF treatment has potential to be practically used for pasteurization of almond kernels with acceptable heating uniformity.

Effects of extrusion variables on the properties of waxy hulless barley extrudates.

PubMed

Köksel, Hamit; Ryu, Gy-Hyung; Başman, Arzu; Demiralp, Hande; Ng, Perry K W

2004-02-01

The objective of this research was to investigate the extrudability of waxy hulless barley flour under various extrusion conditions. Waxy hulless barley flour was processed in a laboratory-scale corotating twin-screw extruder with different levels of feed moisture content (22.3, 26.8, and 30.7%) and die temperature (130, 150, and 170 degrees C) to develop a snack food with high beta-glucan content. The effects of extrusion condition variables (screw configuration, moisture, and temperature) on the system variables (pressure and specific mechanical energy), the extrudate physical properties (sectional expansion index, bulk density), starch gelatinization, pasting properties (cold peak viscosity, trough viscosity, and final viscosity), and beta-glucan contents were determined. Results were evaluated by using response surface methodology. Increased extrusion temperature and feed moisture content resulted in decreases in exit die pressure and specific mechanical energy values. For extrudates extruded under low shear screw configuration (LS), increased barrel temperature decreased sectional expansion index (SEI) values at both low and high moisture contents. The feed moisture seems to have an inverse relationship with SEI over the range studied. Bulk density was higher at higher moisture contents, for both low and high barrel temperatures, for samples extruded under high shear screw configuration (HS) and LS. Cold peak viscosities (CV) were observed in all samples. The CV increased with the increase in extrusion temperature and feed moisture content. Although beta-glucan contents of the LS extrudates were comparable to that of barley flour sample, HS samples had generally lower beta-glucan contents. The extrusion cooking technique seems to be promising for the production of snack foods with high beta-glucan content, especially using LS conditions.

Hyperspectral reflectance imaging technique for visualization of moisture distribution in cooked chicken breast

USDA-ARS?s Scientific Manuscript database

Spectroscopy has proven to be an efficient tool for measuring the properties of meat. In this article, the hyperspectral imaging (HSI) technique is investigated for the determination of moisture content in cooked chicken breast over the VIS/NIR (400–1000 nm) spectral ranges. Moisture measurements we...

Microwave remote sensing of soil moisture content over bare and vegetated fields

NASA Technical Reports Server (NTRS)

Wang, J. R.; Shiue, J. C.; Mcmurtrey, J. E., III (Principal Investigator)

1980-01-01

The author has identified the following significant results. Ground truth of soil moisture content, and ambient air and soil temperatures were acquired concurrently with measurements of soil moisture in bare fields and fields covered with grass, corn, and soybeans obtained with 1.4 GHz and 5 GHz radiometers mounted on a truck. The biomass of the vegetation was sampled about once a week. The measured brightness temperatures over the bare fields were compared with those of radiative transfer model calculations using as inputs the acquired soil moisture and temperatures data with appropriate values of dielectric constants for soil-water mixtures. A good agreement was found between the calculated and measured results over 10 deg to 70 deg incident angles. The presence of vegetation reduced the sensitivity of soil moisture sensing. At 1.4 GHz the sensitivity reduction ranged from about 20% for 10 cm tall grassland cover to over 50 to 60% for the dense soybean field. At 5 GHz corresponding reduction in sensitivity ranged from approximately 70% to approximately 90%.

Temporal variations in soil moisture content and its influence on biomass estimates, observed by UAVSAR, ALOS PALSAR, and in-situ field data

NASA Astrophysics Data System (ADS)

Calderhead, A. I.; Simard, M.; Lavalle, M.

2010-12-01

Temporal changes of repeat-pass SAR backscatter over bare ground or forests results mostly from changes in the target's dielectric properties or moisture content; especially when the timescale is on the order of a few days or weeks. It is important to properly correct for moisture content when using SAR based estimates of tree height or biomass. The objective of this work is to quantify the error in biomass estimates associated with variations in moisture content in temperate and boreal forested areas. In addition, the accuracy of three polarimetric soil moisture surface inversion models (Dubois et al., 1995, Oh et al., 1992; Oh, 2004) are tested on UAVSAR and PALSAR data of bare soils in temperate and boreal forested areas. In addition to PALSAR data from 2007 to 2009, a JPL/UAVSAR campaign over parts of New England and Quebec was completed in August, 2009; L-band SAR images were acquired on August 5th, August 7th, and August 14th. In-situ soil moisture probes at three locations gathered hourly soil moisture content data. LVIS LIDAR is used for quantifying and classifying biomass ranges. Slope corrected backscatter values resampled to 1 hectare at HH, HV, and VV polarizations, and ratios thereof, are compared with soil moisture, precipitation, biomass, and incidence angle. It is seen that the backscatter for high biomass areas varies significantly due to moisture variations. An increase in 1% soil moisture content at the Laurentides field site leads to a change in HV backscatter of 1dB. Regions with high biomass do not vary uniformly with varying moisture content: this can be explained by saturation of the L-band at higher biomass levels. The three inversion algorithms produce varying results with the ‘Dubois et al’ inversion producing the best correlation at the Bartlett Forest site while the ‘Oh 2004’ inversion produces better results at the Laurentides site. Although the accuracy is often poor, the temporal variation of the moisture content for all three inversion algorithms is generally captured.

Effects of particle fracturing and moisture content on fire behaviour in masticated fuelbeds burned in a laboratory

Treesearch

Jesse K. Kreye; J. Morgan Varner; Eric E. Knapp

2011-01-01

Mechanical mastication is a fuels treatment that converts shrubs and small trees into dense fuelbeds composed of fractured woody particles. Although compaction is thought to reduce fireline intensity, the added particle surface area due to fracturing could also influence fire behavior. We evaluated effects of particle fracturing and moisture content (ranging from 2.5...

Impact of acorn moisture content at sowing on germination and seedling growth of white oak and northern red oak

Treesearch

Shi-Jean Susana Sung; Paul P. Kormanik; Taryn L. Kormanik; Stanley J. Zarnoch

2005-01-01

Acorn quality is an integral part of artificial oak regeneration. Progeny from individual mother trees of similar geographic areas frequently exhibited a wide range of germination percentage. The purpose of our study was to evaluate the impact of acorn moisture content (MC) at sowing on germination and subsequent seedling growth.

Soil Texture Often Exerts a Stronger Influence Than Precipitation on Mesoscale Soil Moisture Patterns

NASA Astrophysics Data System (ADS)

Dong, Jingnuo; Ochsner, Tyson E.

2018-03-01

Soil moisture patterns are commonly thought to be dominated by land surface characteristics, such as soil texture, at small scales and by atmospheric processes, such as precipitation, at larger scales. However, a growing body of evidence challenges this conceptual model. We investigated the structural similarity and spatial correlations between mesoscale (˜1-100 km) soil moisture patterns and land surface and atmospheric factors along a 150 km transect using 4 km multisensor precipitation data and a cosmic-ray neutron rover, with a 400 m diameter footprint. The rover was used to measure soil moisture along the transect 18 times over 13 months. Spatial structures of soil moisture, soil texture (sand content), and antecedent precipitation index (API) were characterized using autocorrelation functions and fitted with exponential models. Relative importance of land surface characteristics and atmospheric processes were compared using correlation coefficients (r) between soil moisture and sand content or API. The correlation lengths of soil moisture, sand content, and API ranged from 12-32 km, 13-20 km, and 14-45 km, respectively. Soil moisture was more strongly correlated with sand content (r = -0.536 to -0.704) than with API for all but one date. Thus, land surface characteristics exhibit coherent spatial patterns at scales up to 20 km, and those patterns often exert a stronger influence than do precipitation patterns on mesoscale spatial patterns of soil moisture.

On-line moisture determination of ore concentrates 'a review of traditional methods and introduction of a novel solution'.

PubMed

Cancilla, P A; Barrette, P; Rosenblum, F

2002-12-01

The manual gravimetric drying moisture determination methods currently employed by most mineral processing plants fail to provide timely and accurate information required for automatic control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool. A novel on-line determination system for ore concentrate moisture content would replace the tedious manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum. Therefore, a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the 'wish list' of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done by the classical technique of loss in weight utilizing uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7-9%, but controlling the moisture content below 8% is a difficult task with a manually controlled system. Many times, delays in manually achieving reliable feedback of the moisture content results in the moisture varying from 5-12% before corrective actions can be made. This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principles and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper introduces and describes a novel on-line moisture sensor employed for mineral processing de-watering applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented which indicate the usefulness and summarizes the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content. Copyright 2002 Elsevier Science Ltd.

Moisture transfer from stopper to product and resulting stability implications.

PubMed

Pikal, M J; Shah, S

1992-01-01

Since the stability of a freeze-dried product is often sensitive to the level of moisture, control of residual moisture by attention to the secondary drying phase of the freeze-drying process is of considerable importance. However, several reports in the literature as well as our own experience suggest that low residual moisture immediately after manufacture does not ensure low moisture throughout the shelf life of the product. Equilibration of the product with moisture in the stopper can lead to significant increases in product water content. This research is a study of the kinetic and equilibrium aspects of moisture transfer from stopper to product at 5 degrees C, 25 degrees C, and 40 degrees C for two amorphous materials: vancomycin (highly hygroscopic) and lactose (moderately hygroscopic). Stoppers are 13 mm butyl rubber (#1816, West Co.) slotted freeze-drying stoppers which were studied: (a) "U"-with no treatment; (b) "SV1"-steam-sterilized followed by 1 hr vacuum drying; and (c) "SV8"-steam sterilized followed by 8 hrs vacuum drying. No evidence was found for moisture transmission through the stopper. Rather, the product moisture content increases with time and reaches an apparent equilibrium value characteristic of the product, amount of product, and stopper treatment method ("SV1" much greater than "U" greater than "SV1"). As a first approximation, the rate of approach to "equilibrium" depends only on temperature (t1/2 approximately 10 months at 5 degrees C to approximately 4 days at 40 degrees C) with the "equilibrium" water content being independent of temperature. The "equilibrium" moisture content increases as the dose decreases and is larger for vancomycin than for lactose. The "equilibrium" moisture contents range from 5.0% (25 mg vancomycin, "SV1" stoppers) to 0.68% (100 mg lactose, "SV8" stoppers).

Cryopreservation of lipid-rich seeds: effect of moisture content and cooling rate on germination.

PubMed

González-Benito, E M; Pérez-García, F

2001-01-01

The effect of fast and slow cooling on germination of seeds from two Brassicaceae species (Eruca vesicaria (L.) Cav., Brassica napus L. var. oleifera (Moench) DC cv. Bingo) and cypselas from three Compositae species (Onopordum nervosum Boiss., Onopordum acanthium L., Helianthus annuus L. cv. Viky) at different moisture contents was studied. Seed lipid content (dry weight basis) ranged from 15% (O. nervosum) to 41% (H. annuus). For each species, seeds with four moisture contents were cryopreserved either by direct immersion in liquid nitrogen or by previous cooling at 10 degrees C/min from room temperature to -50 degrees C. In three species (E. vesicaria, B. napus, and H. annuus) germination of air-dried (6.2-8.9% moisture content) seeds cooled by direct immersion in liquid nitrogen was not significantly different from germination of control seeds (air-dried, non-cooled). In the two Onorpordum species the best response among cooling treatments was observed when air-dried seeds were slowly cooled.

Monitoring moisture storage in trees using time domain reflectometry

USGS Publications Warehouse

Constantz, J.; Murphy, F.

1990-01-01

Laboratory and field tests were performed to examine the feasibility of using time domain reflectometry (TDR) to monitor changes in the moisture storage of the woody parts of trees. To serve as wave guides for the TDR signal, pairs of stainless steel rods (13 cm long, 0.32 cm in diameter, and 2.5 cm separation) were driven into parallel pilot holes drilled into the woody parts of trees, and a cable testing oscilloscope was used to determine the apparent dielectric constant. A laboratory calibration test was performed on two sapwood samples, so that the relation between the volumetric water content and the apparent dielectric constant of the sapwood could be determined over a range of water contents. The resulting calibration curve for these sapwood samples was significantly different than the general calibration curve used for soils, showing a smaller change in the apparent dielectric constant for a given change in the volumetric water content than is typical for soils. The calibration curve was used to estimate the average volumetric water content to a depth of 13 cm in living trees. One field experiment was conducted on an English walnut tree (Juglans regia) with a diameter of 40 cm, growing in a flood-irrigated orchard on a Hanford sandy loam near Modesto, California (U.S.A.). Rods were driven into the tree at about 50 cm above the soil surface and monitored hourly for the month of August, 1988. The moisture content determined by TDR showed a gradual decrease from 0.44 to 0.42 cm3 cm-3 over a two week period prior to flood irrigation, followed by a rapid rise to 0.47 cm3 cm-3 over a four day period after irrigation, then again a gradual decline approaching the next irrigation. A second field experiment was made on ten evergreen and deciduous trees with diameters ranging from 30 to 120 cm, growing in the foothills of the Coast Range of central California. Rods were driven into each tree at 50 to 100 cm above the soil surface and monitored on a biweekly to monthly basis for over a year. Most trees showed an early spring maximum in moisture content determined by TDR associated with leaf growth, and a late summer minimum in moisture content associated with the end of the dry season. Moisture contents ranged from 0.20 to 0.70 cm3 cm-3, with an annual percentage change in moisture of 15% to 70% depending on species and environmental conditions. A final field test was performed in northern New Mexico (U.S.A.) to examine the effect of trunk freezing on TDR measurements. This test confirmed that freezing conditions were recorded as a total loss of liquid water by the TDR method. These results suggest that further TDR calibration for wood, plus some understanding of the relation between tree moisture and physiological stress could be useful to several disciplines, ranging from irrigation scheduling to watershed management to forest ecology. ?? 1990.

Monitoring moisture storage in trees using time domain reflectometry

NASA Astrophysics Data System (ADS)

Constantz, Jim; Murphy, Fred

1990-11-01

Laboratory and field tests were performed to examine the feasibility of using time domain reflectometry (TDR) to monitor changes in the moisture storage of the woody parts of trees. To serve as wave guides for the TDR signal, pairs of stainless steel rods (13 cm long, 0.32 cm in diameter, and 2.5 cm separation) were driven into parallel pilot holes drilled into the woody parts of trees, and a cable testing oscilloscope was used to determine the apparent dielectric constant. A laboratory calibration test was performed on two sapwood samples, so that the relation between the volumetric water content and the apparent dielectric constant of the sapwood could be determined over a range of water contents. The resulting calibration curve for these sapwood samples was significantly different than the general calibration curve used for soils, showing a smaller change in the apparent dielectric constant for a given change in the volumetric water content than is typical for soils. The calibration curve was used to estimate the average volumetric water content to a depth of 13 cm in living trees. One field experiment was conducted on an English walnut tree ( Juglans regia) with a diameter of 40 cm, growing in a flood-irrigated orchard on a Hanford sandy loam near Modesto, California (U.S.A.). Rods were driven into the tree at about 50 cm above the soil surface and monitored hourly for the month of August, 1988. The moisture content determined by TDR showed a gradual decrease from 0.44 to 0.42 cm 3 cm -3 over a two week period prior to flood irrigation, followed by a rapid rise to 0.47 cm 3 cm -3 over a four day period after irrigation, then again a gradual decline approaching the next irrigation. A second field experiment was made on ten evergreen and deciduous trees with diameters ranging from 30 to 120 cm, growing in the foothills of the Coast Range of central California. Rods were driven into each tree at 50 to 100 cm above the soil surface and monitored on a biweekly to monthly basis for over a year. Most trees showed an early spring maximum in moisture content determined by TDR associated with leaf growth, and a late summer minimum in moisture content associated with the end of the dry season. Moisture contents ranged from 0.20 to 0.70 cm 3 cm -3, with an annual percentage change in moisture of 15% to 70% depending on species and environmental conditions. A final field test was performed in northern New Mexico (U.S.A.) to examine the effect of trunk freezing on TDR measurements. This test confirmed that freezing conditions were recorded as a total loss of liquid water by the TDR method. These results suggest that further TDR calibration for wood, plus some understanding of the relation between tree moisture and physiological stress could be useful to several disciplines, ranging from irrigation scheduling to watershed management to forest ecology.

Moisture sorption isotherms and thermodynamic properties of mexican mennonite-style cheese.

PubMed

Martinez-Monteagudo, Sergio I; Salais-Fierro, Fabiola

2014-10-01

Moisture adsorption isotherms of fresh and ripened Mexican Mennonite-style cheese were investigated using the static gravimetric method at 4, 8, and 12 °C in a water activity range (aw) of 0.08-0.96. These isotherms were modeled using GAB, BET, Oswin and Halsey equations through weighed non-linear regression. All isotherms were sigmoid in shape, showing a type II BET isotherm, and the data were best described by GAB model. GAB model coefficients revealed that water adsorption by cheese matrix is a multilayer process characterized by molecules that are strongly bound in the monolayer and molecules that are slightly structured in a multilayer. Using the GAB model, it was possible to estimate thermodynamic functions (net isosteric heat, differential entropy, integral enthalpy and entropy, and enthalpy-entropy compensation) as function of moisture content. For both samples, the isosteric heat and differential entropy decreased with moisture content in exponential fashion. The integral enthalpy gradually decreased with increasing moisture content after reached a maximum value, while the integral entropy decreased with increasing moisture content after reached a minimum value. A linear compensation was found between integral enthalpy and entropy suggesting enthalpy controlled adsorption. Determination of moisture content and aw relationship yields to important information of controlling the ripening, drying and storage operations as well as understanding of the water state within a cheese matrix.

Long Term Effects of Poultry Litter on Soil Physical and Chemical Properties in Cotton Plots

NASA Technical Reports Server (NTRS)

Surrency, J.; Tsegaye, T.; Coleman, T.; Fahsi, A.; Reddy, C.

1998-01-01

Poultry litter and compost can alter the moisture holding capacity of a soil. These organic materials can also increase the nutrient status of a soil during the decomposition process by microbial actions. The objective of this study was to evaluate the effect of poultry litter and compost on the dielectric constant and moisture holding capacity of soil. The Delta-T theta-probe was used to measure volumetric soil water content and the apparent dielectric constant of the upper 6-cm of the soil profile. Soil texture, pH, and organic matter were also determined for each plot. Results of these analyses indicated that the pH of the soil ranged from 6.4 to 7.7 and the volumetric soil moisture content ranged from 0.06 to 0.18 cu m/cu m for the upper 6-cm of the soil profile. The effect of poultry litter and compost on soil properties resulted in an increase in the volumetric moisture content and dielectric constant of the soil due to the improvement of the soil structure.

Simultaneous Moisture Content and Mass Flow Measurements in Wood Chip Flows Using Coupled Dielectric and Impact Sensors.

PubMed

Pan, Pengmin; McDonald, Timothy; Fulton, John; Via, Brian; Hung, John

2016-12-23

An 8-electrode capacitance tomography (ECT) sensor was built and used to measure moisture content (MC) and mass flow of pine chip flows. The device was capable of directly measuring total water quantity in a sample but was sensitive to both dry matter and moisture, and therefore required a second measurement of mass flow to calculate MC. Two means of calculating the mass flow were used: the first being an impact sensor to measure total mass flow, and the second a volumetric approach based on measuring total area occupied by wood in images generated using the capacitance sensor's tomographic mode. Tests were made on 109 groups of wood chips ranging in moisture content from 14% to 120% (dry basis) and wet weight of 280 to 1100 g. Sixty groups were randomly selected as a calibration set, and the remaining were used for validation of the sensor's performance. For the combined capacitance/force transducer system, root mean square errors of prediction (RMSEP) for wet mass flow and moisture content were 13.42% and 16.61%, respectively. RMSEP using the combined volumetric mass flow/capacitance sensor for dry mass flow and moisture content were 22.89% and 24.16%, respectively. Either of the approaches was concluded to be feasible for prediction of moisture content in pine chip flows, but combining the impact and capacitance sensors was easier to implement. In situations where flows could not be impeded, however, the tomographic approach would likely be more useful.

Specific energy consumption and quality of wood pellets produced using high-moisture lodgepole pine grind in a flat die pellet mill

DOE PAGES

Tumuluru, Jaya Shankar

2016-04-16

In the present study a Box–Behnken experimental design was used to understand the effect of the moisture content of lodgepole pine grind (33–39%, w.b.), die speed (40–60 Hz) and preheating temperature (30–90 °C) on the pellet quality and specific energy consumption. The partially dried pellets produced had high-moisture content in the range of 19–28% (w.b.), and were further dried to <9% (w.b.) in a mechanical oven set at 70 °C for 3 h. Dried pellets were further evaluated for pellet moisture content, unit, bulk, tapped density, and durability. Response surface models developed for the product properties have adequately described themore » process based on coefficient of determination values. Surface plots developed indicated higher unit, bulk, and tapped density (1050, 520, 560 kg/m 3) are achievable at 33–35% (w.b.) moisture content of the lodgepole pine grind, die speed of 60 Hz and preheating temperature of 30–60 °C. Higher moisture content of 39% (w.b) reduced unit, bulk, and tapped density to <912, 396, and 452 kg/m 3. Higher durability values of >95% were obtained at 33–35% (w.b.) at lower preheating temperatures of 30–50 °C and higher die speed of >50 Hz. At 33% (w.b.) moisture content of the lodgepole pine grind, preheating temperature of 90 °C, and die speed of 60 Hz, the observed specific energy consumption was <116 kW h/ton. As a result, scanning electron microscope studies indicated that lignin crosslinking is the primary reason for binding of the lodgepole pine grind at high-moisture content.« less

Influence of moisture content and temperature on thermal conductivity and thermal diffusivity of rice flours

USDA-ARS?s Scientific Manuscript database

The thermal conductivity and thermal diffusivity of four types of rice flours and one type of rice protein were determine at temperatures ranging from 4.8 to 36.8 C, bulk densities 535 to 875.8 kg/m3, and moisture contents 2.6 to 16.7 percent (w.b.), using a KD2 Thermal Properties Analyzer. It was ...

Effect of Soil Water on Infectivity and Development of Rotylenchulus reniformis on Soybean, Glycine max

PubMed Central

Rebois, R. V.

1973-01-01

The effect of soil water content on Rotylenchulus reniformis infectivity of 'Lee' soybean roots was investigated in an autoclaved sandy clay loam. Nematodes were introduced into soil masses maintained at constant soil water levels ranging from 3.4 to 19% by weight. Seedling growth and the soil water content-water potential relationships of the soil were determined. Nematode infectivity was greatest when the soil water content was maintained just below field capacity in the 7.2 (-1/3 bar) to 13.0% (-1/7 bar) ranges. Nematode invasion of roots was reduced in the wetter 15.5 (-1/10 bar) to 19.0% (-1 /2 0 bar) soil moisture ranges and in the dryer 3.4 (-15 bar) to 5.8% (-3/4 bar) soil moisture ranges. PMID:19319344

Cattle feedlot soil moisture and manure content: I. Impacts on greenhouse gases, odor compounds, nitrogen losses, and dust.

PubMed

Miller, Daniel N; Berry, Elaine D

2005-01-01

Beef cattle feedlots face serious environmental challenges associated with manure management, including greenhouse gas, odor, NH3, and dust emissions. Conditions affecting emissions are poorly characterized, but likely relate to the variability of feedlot surface moisture and manure contents, which affect microbial processes. Odor compounds, greenhouse gases, nitrogen losses, and dust potential were monitored at six moisture contents (0.11, 0.25, 0.43, 0.67, 1.00, and 1.50 g H2O g(-1) dry matter [DM]) in three artificial feedlot soil mixtures containing 50, 250, and 750 g manure kg(-1) total (manure + soil) DM over a two-week period. Moisture addition produced three microbial metabolisms: inactive, aerobic, and fermentative at low, moderate, and high moisture, respectively. Manure content acted to modulate the effect of moisture and enhanced some microbial processes. Greenhouse gas (CO2, N2O, and CH4) emissions were dynamic at moderate to high moisture. Malodorous volatile fatty acid (VFA) compounds did not accumulate in any treatments, but their persistence and volatility varied depending on pH and aerobic metabolism. Starch was the dominant substrate fueling both aerobic and fermentative metabolism. Nitrogen losses were observed in all metabolically active treatments; however, there was evidence for limited microbial nitrogen uptake. Finally, potential dust production was observed below defined moisture thresholds, which were related to manure content of the soil. Managing feedlot surface moisture within a narrow moisture range (0.2-0.4 g H2O g(-1) DM) and minimizing the accumulation of manure produced the optimum conditions that minimized the environmental impact from cattle feedlot production.

Measuring spatial and temporal variation in surface moisture on a coastal beach with a near-infrared terrestrial laser scanner

NASA Astrophysics Data System (ADS)

Smit, Yvonne; Ruessink, Gerben; Brakenhoff, Laura B.; Donker, Jasper J. A.

2018-04-01

Wind-alone predictions of aeolian sand deposition on the most seaward coastal dune ridge often exceed measured deposition substantially. Surface moisture is a major factor limiting aeolian transport on sandy beaches, but existing measurement techniques cannot adequately characterize the spatial and temporal distribution of surface moisture content. Here, we present a new method for detecting surface moisture at high temporal and spatial resolution using a near-infrared terrestrial laser scanner (TLS), the RIEGL VZ-400. Because this TLS operates at a wavelength (1550 nm) near a water absorption band, TLS reflectance is an accurate parameter to measure surface moisture over its full range. Five days of intensive laser scanning were performed on a Dutch beach to illustrate the applicability of the TLS. Gravimetric surface moisture samples were used to calibrate the relation between reflectance and surface moisture. Results reveal a robust negative relation for the full range of possible surface moisture contents (0%-25%), with a correlation-coefficient squared of 0.85 and a root-mean-square error of 2.7%. This relation holds between 20 and 60 m from the TLS. Within this distance the TLS typically produces O (106-107) data points, which we averaged into surface moisture maps with a 1 × 1 m resolution. This grid size largely removes small reflectance disturbances induced by, for example, footprints or tire tracks, while retaining larger scale moisture trends.

Review of in-service moisture and temperature conditions in wood-frame buildings

Treesearch

Samuel V. Glass; Anton TenWolde

2007-01-01

This literature review reports in-service moisture and temperature conditions of floor, wall, and roof members of wood-frame buildings and exposed wood decks and permanent wood foundations. A wide variation exists in reported wood moisture content, spanning a range from as low as 2% to well above 30%. Relevant studies are summarized, and measured values of wood...

Wood and bark moisture contents of small-diameter hardwoods growing on southern pine sites

Treesearch

F.G. Manwiller

1975-01-01

Ten 6-inch trees from throughout the South were sampled from each of 22 species, of which 11 were oaks. Ranking of species remained constant regardless of whether moisture contents were determined for the entire tree, the stem with bark, branches with bark, or stem- and branchwood without bark. For ashes and hickory, the range among these various components was 46 to...

Wood and bark moisture contents of small-diameter hardwoods growing on southern pine sites

Treesearch

Floyd G. Manwiller

1975-01-01

Ten 6-inch trees from throughout the south were sampled from each of 22 species, of which 11 were oaks. Ranking of species remained constant regardless of whether moisture contents were determined for the entire tree, the stem with bark, branches with bark, or stem- and branchwood without bark. For ashes and hickory, the range among these various components was 46 to...

Strategies for multivariate modeling of moisture content in freeze-dried mannitol-containing products by near-infrared spectroscopy.

PubMed

Yip, Wai Lam; Gausemel, Ingvil; Sande, Sverre Arne; Dyrstad, Knut

2012-11-01

Accurate determination of residual moisture content of a freeze-dried (FD) pharmaceutical product is critical for prediction of its quality. Near-infrared (NIR) spectroscopy is a fast and non-invasive method routinely used for quantification of moisture. However, several physicochemical properties of the FD product may interfere with absorption bands related to the water content. A commonly used stabilizer and bulking agent in FD known for variation in physicochemical properties, is mannitol. To minimize this physicochemical interference, different approaches for multivariate correlation between NIR spectra of a FD product containing mannitol and the corresponding moisture content measured by Karl Fischer (KF) titration have been investigated. A novel method, MIPCR (Main and Interactions of Individual Principal Components Regression), was found to have significantly increased predictive ability of moisture content compared to a traditional PLS approach. The philosophy behind the MIPCR is that the interference from a variety of particle and morphology attributes has interactive effects on the water related absorption bands. The transformation of original wavelength variables to orthogonal scores gives a new set of variables (scores) without covariance structure, and the possibility of inclusion of interaction terms in the further modeling. The residual moisture content of the FD product investigated is in the range from 0.7% to 2.6%. The mean errors of cross validated prediction of models developed in the investigated NIR regions were reduced from a range of 24.1-27.6% for traditional PLS method to 15.7-20.5% for the MIPCR method. Improved model quality by application of MIPCR, without the need for inclusion of a large number of calibration samples, might increase the use of NIR in early phase product development, where availability of calibration samples is often limited. Copyright © 2012 Elsevier B.V. All rights reserved.

Simultaneous moisture content and mass flow measurements in wood chip flows using coupled dielectric and impact sensors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, Pengmin; McDonald, Timothy; Fulton, John

An 8-electrode capacitance tomography (ECT) sensor was built and used to measure moisture content (MC) and mass flow of pine chip flows. The device was capable of directly measuring total water quantity in a sample but was sensitive to both dry matter and moisture, and therefore required a second measurement of mass flow to calculate MC. Two means of calculating the mass flow were used: the first being an impact sensor to measure total mass flow, and the second a volumetric approach based on measuring total area occupied by wood in images generated using the capacitance sensor’s tomographic mode. Testsmore » were made on 109 groups of wood chips ranging in moisture content from 14% to 120% (dry basis) and wet weight of 280 to 1100 g. Sixty groups were randomly selected as a calibration set, and the remaining were used for validation of the sensor’s performance. For the combined capacitance/force transducer system, root mean square errors of prediction (RMSEP) for wet mass flow and moisture content were 13.42% and 16.61%, respectively. RMSEP using the combined volumetric mass flow/capacitance sensor for dry mass flow and moisture content were 22.89% and 24.16%, respectively. Either of the approaches was concluded to be feasible for prediction of moisture content in pine chip flows, but combining the impact and capacitance sensors was easier to implement. As a result, in situations where flows could not be impeded, however, the tomographic approach would likely be more useful.« less

Simultaneous moisture content and mass flow measurements in wood chip flows using coupled dielectric and impact sensors

DOE PAGES

Pan, Pengmin; McDonald, Timothy; Fulton, John; ...

2016-12-23

An 8-electrode capacitance tomography (ECT) sensor was built and used to measure moisture content (MC) and mass flow of pine chip flows. The device was capable of directly measuring total water quantity in a sample but was sensitive to both dry matter and moisture, and therefore required a second measurement of mass flow to calculate MC. Two means of calculating the mass flow were used: the first being an impact sensor to measure total mass flow, and the second a volumetric approach based on measuring total area occupied by wood in images generated using the capacitance sensor’s tomographic mode. Testsmore » were made on 109 groups of wood chips ranging in moisture content from 14% to 120% (dry basis) and wet weight of 280 to 1100 g. Sixty groups were randomly selected as a calibration set, and the remaining were used for validation of the sensor’s performance. For the combined capacitance/force transducer system, root mean square errors of prediction (RMSEP) for wet mass flow and moisture content were 13.42% and 16.61%, respectively. RMSEP using the combined volumetric mass flow/capacitance sensor for dry mass flow and moisture content were 22.89% and 24.16%, respectively. Either of the approaches was concluded to be feasible for prediction of moisture content in pine chip flows, but combining the impact and capacitance sensors was easier to implement. As a result, in situations where flows could not be impeded, however, the tomographic approach would likely be more useful.« less

Simultaneous Moisture Content and Mass Flow Measurements in Wood Chip Flows Using Coupled Dielectric and Impact Sensors

PubMed Central

Pan, Pengmin; McDonald, Timothy; Fulton, John; Via, Brian; Hung, John

2016-01-01

An 8-electrode capacitance tomography (ECT) sensor was built and used to measure moisture content (MC) and mass flow of pine chip flows. The device was capable of directly measuring total water quantity in a sample but was sensitive to both dry matter and moisture, and therefore required a second measurement of mass flow to calculate MC. Two means of calculating the mass flow were used: the first being an impact sensor to measure total mass flow, and the second a volumetric approach based on measuring total area occupied by wood in images generated using the capacitance sensor’s tomographic mode. Tests were made on 109 groups of wood chips ranging in moisture content from 14% to 120% (dry basis) and wet weight of 280 to 1100 g. Sixty groups were randomly selected as a calibration set, and the remaining were used for validation of the sensor’s performance. For the combined capacitance/force transducer system, root mean square errors of prediction (RMSEP) for wet mass flow and moisture content were 13.42% and 16.61%, respectively. RMSEP using the combined volumetric mass flow/capacitance sensor for dry mass flow and moisture content were 22.89% and 24.16%, respectively. Either of the approaches was concluded to be feasible for prediction of moisture content in pine chip flows, but combining the impact and capacitance sensors was easier to implement. In situations where flows could not be impeded, however, the tomographic approach would likely be more useful. PMID:28025536

A new method to determine the water activity and the net isosteric heats of sorption for low moisture foods at elevated temperatures.

PubMed

Tadapaneni, Ravi Kiran; Yang, Ren; Carter, Brady; Tang, Juming

2017-12-01

In recent years, research studies have shown that the thermal resistance of foodborne pathogens in the low moisture foods is greatly influenced by the water activity (a w ) at temperatures relevant to thermal treatments for pathogen control. Yet, there has been a lack of an effective method for accurate measurement of a w at those temperatures. Thus, the main aim of this study was to evaluate a new method for measuring a w of food samples at elevated temperatures. An improved thermal cell with a relative humidity and temperature sensor was used to measure the a w of the three different food samples, namely, organic wheat flour, almond flour, and non-fat milk powder, over the temperature range between 20 and 80°C. For a constant moisture content, the a w data was used to estimate the net isosteric heat of sorption (q st ). The q st values were then used in the Clausius Clapeyron equation (CCE) equation to estimate the moisture sorption isotherm for all test food samples at different temperatures. For all the tested samples of any fixed moisture content, a w value generally increased with the temperature. The energy for sorption decreased with increasing moisture content. With the experimentally determined q st value, CCE describes well about the changes in a w of the food samples between 20 and 80°C. This study presents a method to obtain a w of a food sample for a specific moisture content at different temperatures which could be extended to obtain q st values for different moisture contents and hence, the moisture sorption isotherm of a food sample at different temperatures. Copyright © 2017 Elsevier Ltd. All rights reserved.

Peat soils stabilization using Effective Microorganisms (EM)

NASA Astrophysics Data System (ADS)

Yusof, N. Z.; Samsuddin, N. S.; Hanif, M. F.; Syed Osman, S. B.

2018-04-01

Peat soil is known as geotechnical problematic soil since it is the softest soil having highly organic and moisture content which led to high compressibility, low shear strength and long-term settlement. The aim of this study was to obtain the stabilized peat soils using the Effective Microorganisms (EM). The volume of EM added and mixed with peat soils varied with 2%, 4%, 6%, 8% and 10% and then were cured for 7, 14 and 21 days. The experiment was done for uncontrolled and controlled moisture content. Prior conducting the main experiments, the physical properties such as moisture content, liquid limit, specific gravity, and plastic limit etc. were measure for raw peat samples. The Unconfined Compressive Strength (UCS) test was performed followed by regression analysis to check the effect of EM on the soil strength. Obtained results have shown that the mix design for controlled moisture contents showed the promising improvement in their compressive strength. The peat soil samples with 10% of EM shows the highest increment in UCS value and the percentage of increments are in the range of 44% to 65% after curing for 21 days. The regression analysis of the EM with the soil compressive strength showed that in controlled moisture conditions, EM significantly improved the soil stability as the value of R2 ranged between 0.97 – 0.78. The results have indicated that the addition of EM in peat soils provides significant improving in the strength of the soil as well as the other engineering properties.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tumuluru, Jaya Shankar

In the present study a Box–Behnken experimental design was used to understand the effect of the moisture content of lodgepole pine grind (33–39%, w.b.), die speed (40–60 Hz) and preheating temperature (30–90 °C) on the pellet quality and specific energy consumption. The partially dried pellets produced had high-moisture content in the range of 19–28% (w.b.), and were further dried to <9% (w.b.) in a mechanical oven set at 70 °C for 3 h. Dried pellets were further evaluated for pellet moisture content, unit, bulk, tapped density, and durability. Response surface models developed for the product properties have adequately described themore » process based on coefficient of determination values. Surface plots developed indicated higher unit, bulk, and tapped density (1050, 520, 560 kg/m 3) are achievable at 33–35% (w.b.) moisture content of the lodgepole pine grind, die speed of 60 Hz and preheating temperature of 30–60 °C. Higher moisture content of 39% (w.b) reduced unit, bulk, and tapped density to <912, 396, and 452 kg/m 3. Higher durability values of >95% were obtained at 33–35% (w.b.) at lower preheating temperatures of 30–50 °C and higher die speed of >50 Hz. At 33% (w.b.) moisture content of the lodgepole pine grind, preheating temperature of 90 °C, and die speed of 60 Hz, the observed specific energy consumption was <116 kW h/ton. As a result, scanning electron microscope studies indicated that lignin crosslinking is the primary reason for binding of the lodgepole pine grind at high-moisture content.« less

Molecular Modeling for Calculation of Mechanical Properties of Epoxies with Moisture Ingress

NASA Technical Reports Server (NTRS)

Clancy, Thomas C.; Frankland, Sarah J.; Hinkley, J. A.; Gates, T. S.

2009-01-01

Atomistic models of epoxy structures were built in order to assess the effect of crosslink degree, moisture content and temperature on the calculated properties of a typical representative generic epoxy. Each atomistic model had approximately 7000 atoms and was contained within a periodic boundary condition cell with edge lengths of about 4 nm. Four atomistic models were built with a range of crosslink degree and moisture content. Each of these structures was simulated at three temperatures: 300 K, 350 K, and 400 K. Elastic constants were calculated for these structures by monitoring the stress tensor as a function of applied strain deformations to the periodic boundary conditions. The mechanical properties showed reasonably consistent behavior with respect to these parameters. The moduli decreased with decreasing crosslink degree with increasing temperature. The moduli generally decreased with increasing moisture content, although this effect was not as consistent as that seen for temperature and crosslink degree.

Experimental studies on the effect of moisture content and volume resistivity on electrostatic behaviour of pharmaceutical powders.

PubMed

Choi, Kwangseok; Taghavivand, Milad; Zhang, Lifeng

2017-03-15

Pharmaceutical powders are mainly organic materials and are likely to be charged due to repeated inter-particle and particle-wall contacts during industrial processes. This study experimentally investigated the effect of moisture content (ranging from approximately 1.8 to 30wt.%) on tribocharging behaviour of pharmaceutical granules, as well as their apparent volume resistivity. The tribocharging behaviour of pharmaceutical granules was investigated using a rotating device and apparent volume resistivity was measured in a conventional volume resistivity test cell. Additional measurements were performed on individual ingredients, each having the same moisture content as that of the granules, in order to investigate the effect of each single ingredient on the apparent volume resistivity of granules. In this work, the individual ingredients used for granules were: α-Lactose Monohydrate (α-LMH), Microcrystalline Cellulose (MCC), Hydroxypropyl Methylcellulose (HPMC), and Croscarmellose Sodium (CCS). The results showed that the specific charge of granules began to increase at the moisture contents below 5wt.%, which can be referred as critical moisture content of granules. The apparent volume resistivity showed the same behaviour, indicating that the specific charge could be due to an increase in apparent volume resistivity of granules at reduced moisture content. Finally, it was shown that the apparent volume resistivity measured for granules was mainly affected by that of the α-LMH, the major component of granules accounting for 40wt.%. Copyright © 2017 Elsevier B.V. All rights reserved.

Water Sorption Isotherm of Pea Starch Edible Films and Prediction Models.

PubMed

Saberi, Bahareh; Vuong, Quan V; Chockchaisawasdee, Suwimol; Golding, John B; Scarlett, Christopher J; Stathopoulos, Costas E

2015-12-24

The moisture sorption isotherm of pea starch films prepared with various glycerol contents as plasticizer was investigated at different storage relative humidities (11%-96% RH) and at 5 ± 1, 15 ± 1, 25 ± 1 and 40 ± 1 °C by using gravimetric method. The results showed that the equilibrium moisture content of all films increased substantially above a w = 0.6. Films plasticized with glycerol, under all temperatures and RH conditions (11%-96%), adsorbed more moisture resulting in higher equilibrium moisture contents. Reduction of the temperature enhanced the equilibrium moisture content and monolayer water of the films. The obtained experimental data were fitted to different models including two-parameter equations (Oswin, Henderson, Brunauer-Emmitt-Teller (BET), Flory-Huggins, and Iglesias-Chirife), three-parameter equations Guggenhiem-Anderson-deBoer (GAB), Ferro-Fontan, and Lewicki) and a four-parameter equation (Peleg). The three-parameter Lewicki model was found to be the best-fitted model for representing the experimental data within the studied temperatures and whole range of relative humidities (11%-98%). Addition of glycerol increased the net isosteric heat of moisture sorption of pea starch film. The results provide important information with estimating of stability and functional characteristics of the films in various environments.

Water Sorption Isotherm of Pea Starch Edible Films and Prediction Models

PubMed Central

Saberi, Bahareh; Vuong, Quan V.; Chockchaisawasdee, Suwimol; Golding, John B.; Scarlett, Christopher J.; Stathopoulos, Costas E.

2015-01-01

The moisture sorption isotherm of pea starch films prepared with various glycerol contents as plasticizer was investigated at different storage relative humidities (11%–96% RH) and at 5 ± 1, 15 ± 1, 25 ± 1 and 40 ± 1 °C by using gravimetric method. The results showed that the equilibrium moisture content of all films increased substantially above aw = 0.6. Films plasticized with glycerol, under all temperatures and RH conditions (11%–96%), adsorbed more moisture resulting in higher equilibrium moisture contents. Reduction of the temperature enhanced the equilibrium moisture content and monolayer water of the films. The obtained experimental data were fitted to different models including two-parameter equations (Oswin, Henderson, Brunauer–Emmitt–Teller (BET), Flory–Huggins, and Iglesias–Chirife), three-parameter equations Guggenhiem–Anderson–deBoer (GAB), Ferro–Fontan, and Lewicki) and a four-parameter equation (Peleg). The three-parameter Lewicki model was found to be the best-fitted model for representing the experimental data within the studied temperatures and whole range of relative humidities (11%–98%). Addition of glycerol increased the net isosteric heat of moisture sorption of pea starch film. The results provide important information with estimating of stability and functional characteristics of the films in various environments. PMID:28231096

Cryopreservation of mango (Mangifera indica L.) embryogenic cultures.

PubMed

Wu, Yong-Jie; Huang, Xue-Ling; Xiao, Jie-Ning; Li, Xiao-Ju; Zhou, Ming-De; Engelmann, Florent

2003-01-01

Three techniques were compared for cryopreserving embryogenic masses (EMs) sampled from mango (Mangifera indica L.) cv. Zihua embryogenic cultures: (i) encapsulation/dehydration; (ii) pregrowth/dehydration; and (iii) vitrification. In all experiments, EMs were sampled from embryogenic cultures during their exponential growth phase and pretreated for 24 h on solid medium containing 0.5 M sucrose before freezing. No recovery was achieved after cryopreservation using the encapsulation/dehydration technique, whatever the moisture content (fresh weight basis) of EMs, which ranged from 78.3% without dehydration to 40.8% after 6 h dehydration. With the pregrowth plus dehydration technique, limited recovery (8.3%) was achieved after desiccation of EMs for 1 h, to 58.5% MC. Using the vitrification technique, recovery ranged from 94.3% after treatment of EMs with the PVS3 vitrification solution for 20 min (EM moisture content of 34.7%) to 10.9% after a 120 min treatment with the vitrification solution (EM moisture content of 26.0%).

Moisture content of southern pine as related to thrust, torque, and chip formation in boring

Treesearch

Charles W. McMillin; George E. Woodson

1972-01-01

Holes 3-1/2 inches deep were bored with a 1-inch spur machine bit in southern pine having specific gravity of 0.53 (ovendry weight and volume at 10.4 percent moisture). The bit was rotated at 2,4000 rpm and removed chips 0.020 inch thick. For wood mositure contents ranging from ovendry to saturation, thrust was lower when boring along the grain (Average 98 pounds)...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daugherty, W. L.

Destructive and non-destructive examinations have been performed on the components of shipping package 9975-02019 as part of a comprehensive SRS surveillance program for plutonium material stored in the K-Area Complex (KAC). During the field surveillance inspection of this package in KAC, two non-conforming conditions were noted: the axial gap of 1.577 inch exceeded the 1 inch maximum criterion, and two areas of dried glue residue were noted on the upper fiberboard subassembly. This package was subsequently transferred to SRNL for more detailed inspection and destructive examination. In addition to the conditions noted in KAC, the following conditions were noted: -more » Numerous small spots of corrosion were observed along the bottom edge of the drum. - In addition to the smeared glue residue on the upper fiberboard subassembly, there was also a small dark stain. - Mold was present on the side and bottom of the lower fiberboard subassembly. Dark stains from elevated moisture content were also present in these areas. - A dark spot with possible light corrosion was observed on the primary containment vessel flange, and corresponding rub marks were observed on the secondary containment vessel ID. - The fiberboard thermal conductivity in the radial orientation was above the specified range. When the test was repeated with slightly lower moisture content, the result was acceptable. The moisture content for both tests was within a range typical of other packages in storage. The observed conditions must be fully evaluated by KAC to ensure the safety function of the package is being maintained. Several factors can contribute to the concentration of moisture in the fiberboard, including higher than average initial moisture content, higher internal temperature (due to internal heat load and placement within the array of packages), and the creation of additional moisture as the fiberboard begins to degrade.« less

A Real-time Irrigation Forecasting System in Jiefangzha Irrigation District, China

NASA Astrophysics Data System (ADS)

Cong, Z.

2015-12-01

In order to improve the irrigation efficiency, we need to know when and how much to irrigate in real time. If we know the soil moisture content at this time, we can forecast the soil moisture content in the next days based on the rainfall forecasting and the crop evapotranspiration forecasting. Then the irrigation should be considered when the forecasting soil moisture content reaches to a threshold. Jiefangzha Irrigation District, a part of Hetao Irrigation District, is located in Inner Mongolia, China. The irrigated area of this irrigation district is about 140,000 ha mainly planting wheat, maize and sunflower. The annual precipitation is below 200mm, so the irrigation is necessary and the irrigation water comes from the Yellow river. We set up 10 sites with 4 TDR sensors at each site (20cm, 40cm, 60cm and 80cm depth) to monitor the soil moisture content. The weather forecasting data are downloaded from the website of European Centre for Medium-Range Weather Forecasts (ECMWF). The reference evapotranspiration is estimated based on FAO-Blaney-Criddle equation with only the air temperature from ECMWF. Then the crop water requirement is forecasted by the crop coefficient multiplying the reference evapotranspiration. Finally, the soil moisture content is forecasted based on soil water balance with the initial condition is set as the monitoring soil moisture content. When the soil moisture content reaches to a threshold, the irrigation warning will be announced. The irrigation mount can be estimated through three ways: (1) making the soil moisture content be equal to the field capacity; (2) making the soil moisture saturated; or (3) according to the irrigation quota. The forecasting period is 10 days. The system is developed according to B2C model with Java language. All the databases and the data analysis are carried out in the server. The customers can log in the website with their own username and password then get the information about the irrigation forecasting and other information about the irrigation. This system can be expanded in other irrigation districts. In future, it is even possible to upgrade the system for the mobile user.

An algorithm for temperature correcting substrate moisture measurements: aligning substrate moisture responses with environmental drivers in polytunnel-grown strawberry plants

NASA Astrophysics Data System (ADS)

Goodchild, Martin; Janes, Stuart; Jenkins, Malcolm; Nicholl, Chris; Kühn, Karl

2015-04-01

The aim of this work is to assess the use of temperature corrected substrate moisture data to improve the relationship between environmental drivers and the measurement of substrate moisture content in high porosity soil-free growing environments such as coir. Substrate moisture sensor data collected from strawberry plants grown in coir bags installed in a table-top system under a polytunnel illustrates the impact of temperature on capacitance-based moisture measurements. Substrate moisture measurements made in our coir arrangement possess the negative temperature coefficient of the permittivity of water where diurnal changes in moisture content oppose those of substrate temperature. The diurnal substrate temperature variation was seen to range from 7° C to 25° C resulting in a clearly observable temperature effect in substrate moisture content measurements during the 23 day test period. In the laboratory we measured the ML3 soil moisture sensor (ThetaProbe) response to temperature in Air, dry glass beads and water saturated glass beads and used a three-phase alpha (α) mixing model, also known as the Complex Refractive Index Model (CRIM), to derive the permittivity temperature coefficients for glass and water. We derived the α value and estimated the temperature coefficient for water - for sensors operating at 100MHz. Both results are good agreement with published data. By applying the CRIM equation with the temperature coefficients of glass and water the moisture temperature coefficient of saturated glass beads has been reduced by more than an order of magnitude to a moisture temperature coefficient of

A multivariate mixed model system for wood specific gravity and moisture content of planted loblolly pine stands in the southern United States

Treesearch

Finto Antony; Laurence R. Schimleck; Alex Clark; Richard F. Daniels

2012-01-01

Specific gravity (SG) and moisture content (MC) both have a strong influence on the quantity and quality of wood fiber. We proposed a multivariate mixed model system to model the two properties simultaneously. Disk SG and MC at different height levels were measured from 3 trees in 135 stands across the natural range of loblolly pine and the stand level values were used...

Observed effects of soil organic matter content on the microwave emissivity of soils

NASA Technical Reports Server (NTRS)

O'Neill, P. E.; Jackson, T. J.

1990-01-01

In order to determine the significance of organic matter content on the microwave emissivity of soils when estimating soil moisture, field experiments were conducted in which 1.4 GHz microwave emissivity data were collected over test plots of sandy loam soil with different organic matter levels (1.8, 4.0, and 6.1 percent) for a range of soil moisture values. Analyses of the observed data show only minor variation in microwave emissivity due to a change in organic matter content at a given moisture level for soils with similar texture and structure. Predictions of microwave emissivity made using a dielectric model for aggregated soils exhibit the same trends and type of response as the measured data when appropriate values for the input parameters were utilized.

Observed effects of soil organic matter content on the microwave intensity of soils

NASA Technical Reports Server (NTRS)

Jackson, T. J.; Oneill, P. E.

1988-01-01

In order to determine the significance of organic matter content on the microwave emissivity of soils when estimating soil moisture, field experiments were conducted in which 1.4 GHz microwave emissivity data were collected over test plots of sandy loam soil with different organic matter levels (1.8, 4.0, and 6.1 percent) for a range of soil moisture values. Analyses of the observed data show only minor variation in microwave emissivity due to a change in organic matter content at a given moisture level for soils with similar texture and structure. Predictions of microwave emissivity made using a dielectric model for aggregated soils exhibit the same trends and type of response as the measured data when appropriate values for the input parameters were utilized.

Microstrip transmission line for soil moisture measurement

NASA Astrophysics Data System (ADS)

Chen, Xuemin; Li, Jing; Liang, Renyue; Sun, Yijie; Liu, C. Richard; Rogers, Richard; Claros, German

2004-12-01

Pavement life span is often affected by the amount of voids in the base and subgrade soils, especially moisture content in pavement. Most available moisture sensors are based on the capacitive sensing using planar blades. Since the planar sensor blades are fabricated on the same surface to reduce the overall size of the sensor, such structure cannot provide very high accuracy for moisture content measurement. As a consequence, a typical capacitive moisture sensor has an error in the range of 30%. A more accurate measurement is based on the time domain refelctometer (TDR) measurement. However, typical TDR system is fairly expensive equipment, very large in size, and difficult to operate, the moisture content measurement is limited. In this paper, a novel microstrip transmission line based moisture sensor is presented. This sensor uses the phase shift measurement of RF signal going through a transmission line buried in the soil to be measured. Since the amplitude of the transmission measurement is a strong function of the conductivity (loss of the media) and the imaginary part of dielectric constant, and the phase is mainly a strong function of the real part of the dielectric constant, measuring phase shift in transmission mode can directly obtain the soil moisture information. This sensor was designed and implemented. Sensor networking was devised. Both lab and field data show that this sensor is sensitive and accurate.

Decreasing effect and mechanism of moisture content of sludge biomass by granulation process.

PubMed

Zhao, Xia; Xu, Hao; Shen, Jimin; Yu, Bo; Wang, Xiaochun

2016-01-01

Disposal of a high volume of sludge significantly raises water treatment costs. A method for cultivating aerobic granules in a sequencing batch airlift bioreactor to significantly produce lower moisture content is described. Results indicate that optimization of settling time and control of the shear stresses acted on the granules. The diameter of the granule was within the range of 1.0-4.0 mm, and its sludge volume index was stabilized at 40-50 mL g(-1). Its specific gravity was increased by a factor of 0.0392, and specific oxygen uptake rate reached 60.126 mg h(-1) g(-1). Moreover, the percentage of its moisture content in the reactor ranged from 96.73% to 97.67%, and sludge volume was reduced to approximately 60%, greatly due to the presence of extracellular polymeric substances in the granules, as well as changes in their hydrophobic protein content. The removal rate of chemical oxygen demand and [Formula: see text] reaches up to 92.6% and 98%, respectively. The removal rates of total phosphorus is over 85%. Therefore, aerobic granular sludge process illustrates a good biological activity.

Vegetation Water Content Mapping for Agricultural Regions in SMAPVEX16

NASA Astrophysics Data System (ADS)

White, W. A.; Cosh, M. H.; McKee, L.; Berg, A. A.; McNairn, H.; Hornbuckle, B. K.; Colliander, A.; Jackson, T. J.

2017-12-01

Vegetation water content impacts the ability of L-band radiometers to measure surface soil moisture. Therefore it is necessary to quantify the amount of water held in surface vegetation for an accurate soil moisture remote sensing retrieval. A methodology is presented for generating agricultural vegetation water content maps using Landsat 8 scenes for agricultural fields of Iowa and Manitoba for the Soil Moisture Active Passive Validation Experiments in 2016 (SMAPVEX16). Manitoba has a variety of row crops across the region, and the study period encompasses the time frame from emergence to reproduction, as well as a forested region. The Iowa study site is dominated by corn and soybeans, presenting an easier challenge. Ground collection of vegetation biomass and water content were also collected to provide a ground truth data source. Errors for the resulting vegetation water content maps ranged depending upon crop type, but generally were less than 15% of the total plant water content per crop type. Interpolation is done between Landsat overpasses to produce daily vegetation water content maps for the summer of 2016 at a 30 meter resolution.

Short-term thermal stability of transformer and motor oils at wide range of moisture contents

NASA Astrophysics Data System (ADS)

Volosnikov, D. V.; Povolotskiy, I. I.; Skripov, P. V.

2018-01-01

Method of controlled pulse heating of a wire probe was used for studying heat transfer and thermal stability of energy oils and motor oils in the presence of low quantities of moisture. The technique of two-pulse heating is the most suitable method for monitoring the actual state of oils. A distinct signal-response accompanying the appearance of moisture in the tested sample has been revealed.

Effects of moisture content on coarse woody debris respiration in a tropical rainforest of Brunei Darussalam

NASA Astrophysics Data System (ADS)

Roh, Y.; Li, G.; Han, S. H.; Abu Salim, K.; Son, Y.

2017-12-01

Since coarse woody debris (CWD) respiration (Rcwd) has an important role in carbon (C) cycling in forest ecosystems, it is a significant parameter in an investigation of CWD decomposition rate. Rcwd is known as to be influenced not only by environmental factors but also by CWD properties (e.g., moisture content). This study investigated the effects of CWD moisture content on Rcwd in a lowland mixed Dipterocarp tropical rainforest of Brunei Darussalam. CWDs in the forest were selected and categorized into two decay classes (sound and partially decomposed), and three diameter classes (10-20 cm, 20-30 cm, more than 30 cm). Samplings of CWDs were conducted in February and October, 2016. The fresh weight and Rcwd of the samples were measured within 24 h of sampling. Rcwd measurements were conducted using a closed chamber system with a diffusion-type, non-dispersive infrared (NDIR) sensor. In February, the fresh weight and Rcwd of the samples were remeasured, after submerging them in the fresh water for 24, 48, and 72 h. The Rcwd increased significantly with moisture content in February (r2=0.25, p<0.01). During the study period from February to October, 2016, the mean value of Rcwd (±SE) decreased from 18.26 (3.45) to 14.92 (2.67) mg C kg-1 h-1 (p<0.05), although the moisture content did not change significantly (p>0.05). Rcwd was lowest in the largest diameter class (p<0.01), and not significantly different between the decay classes (p>0.05). On the basis of these results, the Rcwd in this site was in the range of Rcwd in previous studies conducted in other tropical rainforests. Rcwd increased with moisture content, however, the contribution of moisture content to changes in Rcwd might not be influential during the eight months study period.*Supported by research grants from the Korea Forest Service (2017044B10-1719-BB01).

Predicted harvest time effects on switchgrass moisture content, nutrient concentration, yield, and profitability

USDA-ARS?s Scientific Manuscript database

Production costs change with harvest date of switchgrass (Panicum virgatum L.) as a result of nutrient recycling and changes in yield of this perennial crop. This study examines the range of cost of production from an early, yield-maximizing harvest date to a late winter harvest date at low moisture...

Water adsorption isotherms of carboxymethyl cellulose, guar, locust bean, tragacanth and xanthan gums.

PubMed

Torres, María D; Moreira, Ramón; Chenlo, Francisco; Vázquez, María J

2012-06-20

Water adsorption isotherms of carboxymethyl cellulose (CMC), guar gum (GG), locust bean gum (LBG), tragacanth gum (TG) and xanthan gum (XG) were determined at different temperatures (20, 35, 50, and 65°C) using a gravimetric method. Several saturated salt solutions were selected to obtain different water activities in the range from 0.09 to 0.91. Water adsorption isotherms of tested hydrocolloids were classified like type II isotherms. In all cases, equilibrium moisture content decreased with increasing temperature at each water activity value. Three-parameter Guggenheim-Anderson-de Boer (GAB) model was employed to fit the experimental data in the water activity range and statistical analysis indicated that this model gave satisfactory results. CMC and GG were the most and the least hygroscopic gums, respectively. Sorption heats decreased with increasing moisture content. Monolayer moisture content evaluated with GAB model was consistent with equilibrium conditions of maximum stability calculated from thermodynamic analysis of net integral entropy. Values of equilibrium relative humidity at 20°C are proposed to storage adequately the tested gums. Copyright © 2012 Elsevier Ltd. All rights reserved.

Drying and control of moisture content and dimensional changes

Treesearch

Richard Bergman

2010-01-01

The discussion in this chapter is concerned with moisture content determination, recommended moisture content values, drying methods, methods of calculating dimensional changes, design factors affecting such changes in structures, and moisture content control during transit, storage, and construction. Data on green moisture content, fiber saturation point, shrinkage,...

Capacitance Sensor For Nondestructive Determination Of Total Oil Content In Nuts

USDA-ARS?s Scientific Manuscript database

Earlier a simple, low cost instrument was designed and assembled in our laboratory, that could estimate the moisture content (MC) of in-shell peanuts (MC range 9% to 20%) and yellow-dent field corn (MC range 7% to 18%). In this method a sample of of in-shell peanuts or corn was placed between a set...

The effect of moisture content on the thermal conductivity of moss and organic soil horizons from black spruce ecosystems in interior alaska

USGS Publications Warehouse

O'Donnell, J. A.; Romanovsky, V.E.; Harden, J.W.; McGuire, A.D.

2009-01-01

Organic soil horizons function as important controls on the thermal state of near-surface soil and permafrost in high-latitude ecosystems. The thermal conductivity of organic horizons is typically lower than mineral soils and is closely linked to moisture content, bulk density, and water phase. In this study, we examined the relationship between thermal conductivity and soil moisture for different moss and organic horizon types in black spruce ecosystems of interior Alaska. We sampled organic horizons from feather moss-dominated and Sphagnum-dominated stands and divided horizons into live moss and fibrous and amorphous organic matter. Thermal conductivity measurements were made across a range of moisture contents using the transient line heat source method. Our findings indicate a strong positive and linear relationship between thawed thermal conductivity (Kt) and volumetric water content. We observed similar regression parameters (?? or slope) across moss types and organic horizons types and small differences in ??0 (y intercept) across organic horizon types. Live Sphagnum spp. had a higher range of Kt than did live feather moss because of the field capacity (laboratory based) of live Sphagnum spp. In northern regions, the thermal properties of organic soil horizons play a critical role in mediating the effects of climate warming on permafrost conditions. Findings from this study could improve model parameterization of thermal properties in organic horizons and enhance our understanding of future permafrost and ecosystem dynamics. ?? 2009 by Lippincott Williams & Wilkins, Inc.

Use of Temperature and Humidity Sensors to Determine Moisture Content of Oolong Tea

PubMed Central

Chen, Andrew; Chen, Hsuan-Yu; Chen, Chiachung

2014-01-01

The measurement of tea moisture content is important for processing and storing tea. The moisture content of tea affects the quality and durability of the product. Some electrical devices have been proposed to measure the moisture content of tea leaves but are not practical. Their performance is influenced by material density and packing. The official oven method is time-consuming. In this study, the moisture content of Oolong tea was measured by the equilibrium relative humidity technique. The equilibrium relative humidity, and temperature, of tea materials were measured by using temperature and relative humidity sensors. Sensors were calibrated, and calibration equations were established to improve accuracy. The moisture content was calculated by using an equilibrium moisture content model. The error of the moisture content determined with this method was within 0.5% w.b. at moisture <15% w.b. Uncertainty analysis revealed that the performance of the humidity sensor had a significant effect on the accuracy of moisture determination. PMID:25153142

Factors influencing fire behaviour in shrublands of different stand ages and the implications for using prescribed burning to reduce wildfire risk.

PubMed

Baeza, M J; De Luís, M; Raventós, J; Escarré, A

2002-06-01

Fire behaviour under experimental conditions is described in nine Mediterranean gorse shrublands ranging from 3-12 years of age with different fuel loads. Significant differences in the fire-line intensity, fuel load and rate of fire spread have been found to be related to the stage of development of the communities. Fire spread is correlated with fuel moisture using multiple regression techniques. Differences in fuel moisture between mature and young communities under moderate weather conditions have been found. The lower moisture content identified in the mature shrubland is due both to the decreasing moisture content of senescent shrubland in some species, mainly in live fractions of Ulex parviflorus Pour. fuel, and to a substantial increase in dead fuel fractions with low percentages of moisture content. The result is that the older the shrubland is, the greater will be the decrease in the total moisture content of the vegetation. In these moderate weather conditions, the fire intensity of the mature community was as high as the maximum intensity recommended for prescribed fires. This fact seems to indicate that, even under moderate conditions, prescribed burning as an alternative management tool in the mature shrubland must always take into account fuel control; on the other hand, this technique could be applied more easily when the shrubland is at an intermediate growth stage (4-5 years of age). Therefore, more frequent low-intensity prescribed fires are indicated to abate the risk of catastrophic fire.

Effect of processing conditions on oil point pressure of moringa oleifera seed.

PubMed

Aviara, N A; Musa, W B; Owolarafe, O K; Ogunsina, B S; Oluwole, F A

2015-07-01

Seed oil expression is an important economic venture in rural Nigeria. The traditional techniques of carrying out the operation is not only energy sapping and time consuming but also wasteful. In order to reduce the tedium involved in the expression of oil from moringa oleifera seed and develop efficient equipment for carrying out the operation, the oil point pressure of the seed was determined under different processing conditions using a laboratory press. The processing conditions employed were moisture content (4.78, 6.00, 8.00 and 10.00 % wet basis), heating temperature (50, 70, 85 and 100 °C) and heating time (15, 20, 25 and 30 min). Results showed that the oil point pressure increased with increase in seed moisture content, but decreased with increase in heating temperature and heating time within the above ranges. Highest oil point pressure value of 1.1239 MPa was obtained at the processing conditions of 10.00 % moisture content, 50 °C heating temperature and 15 min heating time. The lowest oil point pressure obtained was 0.3164 MPa and it occurred at the moisture content of 4.78 %, heating temperature of 100 °C and heating time of 30 min. Analysis of Variance (ANOVA) showed that all the processing variables and their interactions had significant effect on the oil point pressure of moringa oleifera seed at 1 % level of significance. This was further demonstrated using Response Surface Methodology (RSM). Tukey's test and Duncan's Multiple Range Analysis successfully separated the means and a multiple regression equation was used to express the relationship existing between the oil point pressure of moringa oleifera seed and its moisture content, processing temperature, heating time and their interactions. The model yielded coefficients that enabled the oil point pressure of the seed to be predicted with very high coefficient of determination.

Idealized modeling of convective organization with changing sea surface temperatures using multiple equilibria in weak temperature gradient simulations

NASA Astrophysics Data System (ADS)

Sentić, Stipo; Sessions, Sharon L.

2017-06-01

The weak temperature gradient (WTG) approximation is a method of parameterizing the influences of the large scale on local convection in limited domain simulations. WTG simulations exhibit multiple equilibria in precipitation; depending on the initial moisture content, simulations can precipitate or remain dry for otherwise identical boundary conditions. We use a hypothesized analogy between multiple equilibria in precipitation in WTG simulations, and dry and moist regions of organized convection to study tropical convective organization. We find that the range of wind speeds that support multiple equilibria depends on sea surface temperature (SST). Compared to the present SST, low SSTs support a narrower range of multiple equilibria at higher wind speeds. In contrast, high SSTs exhibit a narrower range of multiple equilibria at low wind speeds. This suggests that at high SSTs, organized convection might occur with lower surface forcing. To characterize convection at different SSTs, we analyze the change in relationships between precipitation rate, atmospheric stability, moisture content, and the large-scale transport of moist entropy and moisture with increasing SSTs. We find an increase in large-scale export of moisture and moist entropy from dry simulations with increasing SST, which is consistent with a strengthening of the up-gradient transport of moisture from dry regions to moist regions in organized convection. Furthermore, the changes in diagnostic relationships with SST are consistent with more intense convection in precipitating regions of organized convection for higher SSTs.

Effect of heat-moisture treatment on multi-scale structures and physicochemical properties of breadfruit starch.

PubMed

Tan, Xiaoyan; Li, Xiaoxi; Chen, Ling; Xie, Fengwei; Li, Lin; Huang, Jidong

2017-04-01

Breadfruit starch was subjected to heat-moisture treatment (HMT) at different moisture content (MC). HMT did not apparently change the starch granule morphology but decreased the molecular weight and increased the amylose content. With increased MC, HMT transformed the crystalline structure (B→A+B→A) and decreased the relative crystallinity. With ≥25% MC, the scattering peak at ca. 0.6nm -1 disappeared, suggesting the lamellar structure was damaged. Compared with native starch, HMT-modified samples showed greater thermostability. Increased MC contributed to a higher pasting temperature, lower viscosity, and no breakdown. The pasting temperature of native and HMT samples ranged from 68.8 to 86.2°C. HMT increased the slowly-digestible starch (SDS) and resistant starch (RS) contents. The SDS content was 13.24% with 35% MC, which was 10.25% higher than that of native starch. The increased enzyme resistance could be ascribed to the rearrangement of molecular chains and more compact granule structure. Copyright © 2017 Elsevier Ltd. All rights reserved.

COMPARING MOISTURE METER READINGS WITH MEASURED EQUILIBRIUM MOISTURE CONTENT OF GYPSUM BOARD

EPA Science Inventory

Moisture meters routinely used in the field to determine the moisture content in gypsum wallboard are primarily designed and manufactured to measure the moisture content of wood. Often they are used to decide whether to replace wallboard by determining if moisture is qualitativel...

NIR technology for on-line determination of superficial a(w) and moisture content during the drying process of fermented sausages.

PubMed

Collell, Carles; Gou, Pere; Arnau, Jacint; Muñoz, Israel; Comaposada, Josep

2012-12-01

Three different NIR equipment were evaluated based on their ability to predict superficial water activity (a(w)) and moisture content in two types of fermented sausages (with and without moulds on surface), using partial least squares (PLS) regression models. The instruments differed mainly in wavelength range, resolution and measurement configuration. The most accurate equipment was used in a new experiment to achieve robust models in sausages with different salt contents and submitted to different drying conditions. The models developed showed determination coefficients (R(2)(P)) values of 0.990, 0.910 and 0.984, and RMSEP values of 1.560%, 0.220% and 0.007% for moisture, salt and a(w) respectively. It was demonstrated that NIR spectroscopy could be a suitable non-destructive method for on-line monitoring and control of the drying process in fermented sausages. Copyright © 2012 Elsevier Ltd. All rights reserved.

Method for the measurement of forest duff moisture content

Treesearch

Peter R. Robichaud; Roger D. Hungerford; David S. Gasvoda

2000-01-01

An apparatus and method for the moisture content measurement of compressible materials using pressure to firmly hold surface probes against the material to be measured. The apparatus uses moisture measurement circuitry employed in frequency domain impedance or time domain reflectometry devices to obtain moisture content readings from materials. These moisture content...

Apparatus and method for the measurement of forest duff moisture content

Treesearch

Peter R. Robichaud; Roger D. Hungerford; David S. Gasvoda

1999-01-01

An apparatus and method for the moisture content measurement of compressible materials using pressure to firmly hold surface probes against the marerial to be measured. The apparatus uses moisture measurement circuitry employed in frequency domain impedance or time domain reflectometry devices to obtain moisture content readings from materials. These moisture content...

Measuring the spatial variation in surface moisture on a coastal beach with an infra-red terrestrial laser scanner

NASA Astrophysics Data System (ADS)

Smit, Yvonne; Donker, Jasper; Ruessink, Gerben

2016-04-01

Coastal sand dunes provide essential protection against marine flooding. Consequently, dune erosion during severe storms has been studied intensively, resulting in well-developed erosion models for use in scientific and applied projects. Nowadays there is growing awareness that similarly advanced knowledge on dune recovery and growth is needed to predict future dune development. For this reason, aeolian sand transport from the beach into the dunes has to be investigated thoroughly. Surface moisture is a major factor limiting aeolian transport on sandy beaches. By increasing the velocity threshold for sediment entrainment, pick-up rates reduce and the fetch length increases. Conventional measurement techniques cannot adequately characterize the spatial and temporal distribution of surface moisture content required to study the effects on aeolian transport. Here we present a new method for detecting surface moisture at high temporal and spatial resolution using the RIEGL VZ-400 terrestrial laser scanner (TLS). Because this TLS operates at a wavelength near a water absorption band (1550 nm), TLS reflectance is an accurate parameter to measure surface soil moisture over its full range. Three days of intensive laser scanning were performed on a Dutch beach to illustrate the applicability of the TLS. Gravimetric soil moisture samples were used to calibrate the relation between reflectance and surface moisture. Results reveal a robust negative relation for the full range of possible surface moisture contents (0% - 25%). This relation holds to about 80 m from the TLS. Within this distance the TLS typically produces O(106-107) data points, which we averaged into soil moisture maps with a 0.25x0.25 m resolution. This grid size largely removes small moisture disturbances induced by, for example, footprints or tire tracks, while retaining larger scale trends. As the next step in our research, we will analyze the obtained maps to determine which processes affect the spatial and temporal surface-moisture variability.

High resolution change estimation of soil moisture and its assimilation into a land surface model

NASA Astrophysics Data System (ADS)

Narayan, Ujjwal

Near surface soil moisture plays an important role in hydrological processes including infiltration, evapotranspiration and runoff. These processes depend non-linearly on soil moisture and hence sub-pixel scale soil moisture variability characterization is important for accurate modeling of water and energy fluxes at the pixel scale. Microwave remote sensing has evolved as an attractive technique for global monitoring of near surface soil moisture. A radiative transfer model has been tested and validated for soil moisture retrieval from passive microwave remote sensing data under a full range of vegetation water content conditions. It was demonstrated that soil moisture retrieval errors of approximately 0.04 g/g gravimetric soil moisture are attainable with vegetation water content as high as 5 kg/m2. Recognizing the limitation of low spatial resolution associated with passive sensors, an algorithm that uses low resolution passive microwave (radiometer) and high resolution active microwave (radar) data to estimate soil moisture change at the spatial resolution of radar operation has been developed and applied to coincident Passive and Active L and S band (PALS) and Airborne Synthetic Aperture Radar (AIRSAR) datasets acquired during the Soil Moisture Experiments in 2002 (SMEX02) campaign with root mean square error of 10% and a 4 times enhancement in spatial resolution. The change estimation algorithm has also been used to estimate soil moisture change at 5 km resolution using AMSR-E soil moisture product (50 km) in conjunction with the TRMM-PR data (5 km) for a 3 month period demonstrating the possibility of high resolution soil moisture change estimation using satellite based data. Soil moisture change is closely related to precipitation and soil hydraulic properties. A simple assimilation framework has been implemented to investigate whether assimilation of surface layer soil moisture change observations into a hydrologic model will potentially improve it performance. Results indicate an improvement in model prediction of near surface and deep layer soil moisture content when the update is performed to the model state as compared to free model runs. It is also seen that soil moisture change assimilation is able to mitigate the effect of erroneous precipitation input data.

Effect of water content on the glass transition temperature of mixtures of sugars, polymers, and penetrating cryoprotectants in physiological buffer.

PubMed

Drake, Andrew C; Lee, Youngjoo; Burgess, Emma M; Karlsson, Jens O M; Eroglu, Ali; Higgins, Adam Z

2018-01-01

Long-term storage of viable mammalian cells is important for applications ranging from in vitro fertilization to cell therapy. Cryopreservation is currently the most common approach, but storage in liquid nitrogen is relatively costly and the requirement for low temperatures during shipping is inconvenient. Desiccation is an alternative strategy with the potential to enable viable cell preservation at more convenient storage temperatures without the need for liquid nitrogen. To achieve stability during storage in the dried state it is necessary to remove enough water that the remaining matrix forms a non-crystalline glassy solid. Thus, the glass transition temperature is a key parameter for design of cell desiccation procedures. In this study, we have investigated the effects of moisture content on the glass transition temperature (Tg) of mixtures of sugars (trehalose or raffinose), polymers (polyvinylpyrrolidone or Ficoll), penetrating cryoprotectants (ethylene glycol, propylene glycol, or dimethyl sulfoxide), and phosphate buffered saline (PBS) solutes. Aqueous solutions were dried to different moisture contents by equilibration with saturated salt solutions, or by baking at 95°C. The glass transition temperatures of the dehydrated samples were then measured by differential scanning calorimetry. As expected, Tg increased with decreasing moisture content. For example, in a desiccation medium containing 0.1 M trehalose in PBS, Tg ranged from about 360 K for a completely dry sample to about 220 K at a water mass fraction of 0.4. Addition of polymers to the solutions increased Tg, while addition of penetrating cryoprotectants decreased Tg. Our results provide insight into the relationship between relative humidity, moisture content and glass transition temperature for cell desiccation solutions containing sugars, polymers and penetrating cryoprotectants.

Effect of water content on the glass transition temperature of mixtures of sugars, polymers, and penetrating cryoprotectants in physiological buffer

PubMed Central

Burgess, Emma M.; Karlsson, Jens O. M.; Eroglu, Ali

2018-01-01

Long-term storage of viable mammalian cells is important for applications ranging from in vitro fertilization to cell therapy. Cryopreservation is currently the most common approach, but storage in liquid nitrogen is relatively costly and the requirement for low temperatures during shipping is inconvenient. Desiccation is an alternative strategy with the potential to enable viable cell preservation at more convenient storage temperatures without the need for liquid nitrogen. To achieve stability during storage in the dried state it is necessary to remove enough water that the remaining matrix forms a non-crystalline glassy solid. Thus, the glass transition temperature is a key parameter for design of cell desiccation procedures. In this study, we have investigated the effects of moisture content on the glass transition temperature (Tg) of mixtures of sugars (trehalose or raffinose), polymers (polyvinylpyrrolidone or Ficoll), penetrating cryoprotectants (ethylene glycol, propylene glycol, or dimethyl sulfoxide), and phosphate buffered saline (PBS) solutes. Aqueous solutions were dried to different moisture contents by equilibration with saturated salt solutions, or by baking at 95°C. The glass transition temperatures of the dehydrated samples were then measured by differential scanning calorimetry. As expected, Tg increased with decreasing moisture content. For example, in a desiccation medium containing 0.1 M trehalose in PBS, Tg ranged from about 360 K for a completely dry sample to about 220 K at a water mass fraction of 0.4. Addition of polymers to the solutions increased Tg, while addition of penetrating cryoprotectants decreased Tg. Our results provide insight into the relationship between relative humidity, moisture content and glass transition temperature for cell desiccation solutions containing sugars, polymers and penetrating cryoprotectants. PMID:29304068

Evaluation of the mass transfer process on thin layer drying of papaya seeds from the perspective of diffusive models

NASA Astrophysics Data System (ADS)

Dotto, Guilherme Luiz; Meili, Lucas; Tanabe, Eduardo Hiromitsu; Chielle, Daniel Padoin; Moreira, Marcos Flávio Pinto

2018-02-01

The mass transfer process that occurs in the thin layer drying of papaya seeds was studied under different conditions. The external mass transfer resistance and the dependence of effective diffusivity ( D EFF ) in relation to the moisture ratio ( \\overline{MR} ) and temperature ( T) were investigated from the perspective of diffusive models. It was verified that the effective diffusivity was affected by the moisture content and temperature. A new correlation was proposed for drying of papaya seeds in order to describe these influences. Regarding the use of diffusive models, the results showed that, at conditions of low drying rates ( T ≤ 70 °C), the external mass transfer resistance, as well as the dependence of the effective diffusivity with respect to the temperature and moisture content should be considered. At high drying rates ( T > 90 °C), the dependence of the effective diffusivity with respect to the temperature and moisture content can be neglected, but the external mass transfer resistance was still considerable in the range of air velocities used in this work.

Moisture Sorption Behaviour and Mould Ecology of Trade Garri Sold in South Eastern Nigeria

PubMed Central

Samuel, Tochukwu; Ugwuanyi, J. Obeta

2014-01-01

Garri is a creamy white or yellow starchy grit produced by roasting to gelatinization and dryness of peeled, washed, mashed, and fermented dewatered cassava roots. It is the most important product of cassava in West and Central Africa. Mean moisture content of yellow and white garri was 11.11% and 10.81% within 24 hrs of sampling from the market, increasing to 17.27% and 16.14%, respectively, following 3 months of storage at room temperature. The water activity of samples varied from initial 0.587 to 0.934 following storage. Moisture sorption isotherms, determined by static gravimetric techniques at 20° and 30°C, showed temperature dependent BET Sigmoidal type II behaviour typical of carbohydrate rich foods but modulated very slightly by the content of palm oil. Equilibrium moisture content decreased with increase in temperature at constant water activity. A total of 10 fungal species belonging to the genera Mucor, Penicillium, Cephalosporium, Aspergillus, Scopulariopsis, Rhizopus, and Paecilomyces were identified, with range increasing with water activity of samples. PMID:26904621

Influence of pin and hammer mill on grinding characteristics, thermal and antioxidant properties of coriander powder.

PubMed

Barnwal, P; Singh, K K; Sharma, Alka; Choudhary, A K; Saxena, S N

2015-12-01

In present study, influence of grinding (hammer and pin mills) and moisture content (range: 6.4-13.6 % dry basis) on the quality traits of coriander powder were investigated. These include grinding parameters, colour parameters, specific heat, thermal conductivity, thermal diffusivity, glass transition temperature, essential oil, total phenolic content, total flavonoid content and DPPH scavenging (%) of coriander powder. For coriander seed, the geometric properties such as major, medium, minor dimensions, geometric mean diameter, arithmetic mean diameter, sphericity, surface area and volume of coriander seeds increased significantly with increasing moisture (6.4-13.6 % db). For coriander powder, the grinding parameters such as average particle size, volume surface mean diameter and volume mean diameter increased significantly with increasing moisture (6.4-13.6 % db). With the grinding method, the colour attributes of coriander powder such as L-value, a-value, b-value, hue angle and browning index varied significantly. It was observed that the specific heat followed second order polynomial relationship with temperature and moisture whereas thermal conductivity varied linearly with temperature and moisture content. The variation of glass transition temperature with moisture can be best represented in quadratic manner. Total flavonoid content (mg QE/g crude seed extract) and DPPH scavenging % activity of coriander powder is significantly affected by grinding methods. A lower value of specific heat was observed for hammer ground coriander powder as compared to pin mill ground coriander powder. The thermal conductivity of hammer mill ground coriander powder was higher as compared to pin mill ground coriander. It was observed that hammer mill yields more fine coriander powder in comparison to pin mill. The browning index was more in hammer mill ground coriander powder.

Innovative application of the moisture analyzer for determination of dry mass content of processed cheese

NASA Astrophysics Data System (ADS)

Kowalska, Małgorzata; Janas, Sławomir; Woźniak, Magdalena

2018-04-01

The aim of this work was the presentation of an alternative method of determination of the total dry mass content in processed cheese. The authors claim that the presented method can be used in industry's quality control laboratories for routine testing and for quick in-process control. For the test purposes both reference method of determination of dry mass in processed cheese and moisture analyzer method were used. The tests were carried out for three different kinds of processed cheese. In accordance with the reference method, the sample was placed on a layer of silica sand and dried at the temperature of 102 °C for about 4 h. The moisture analyzer test required method validation, with regard to drying temperature range and mass of the analyzed sample. Optimum drying temperature of 110 °C was determined experimentally. For Hochland cream processed cheese sample, the total dry mass content, obtained using the reference method, was 38.92%, whereas using the moisture analyzer method, it was 38.74%. An average analysis time in case of the moisture analyzer method was 9 min. For the sample of processed cheese with tomatoes, the reference method result was 40.37%, and the alternative method result was 40.67%. For the sample of cream processed cheese with garlic the reference method gave value of 36.88%, and the alternative method, of 37.02%. An average time of those determinations was 16 min. Obtained results confirmed that use of moisture analyzer is effective. Compliant values of dry mass content were obtained for both of the used methods. According to the authors, the fact that the measurement took incomparably less time for moisture analyzer method, is a key criterion of in-process control and final quality control method selection.

Influence of moisture content, particle size and forming temperature on productivity and quality of rice straw pellets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishii, Kazuei, E-mail: k-ishii@eng.hokudai.ac.jp; Furuichi, Toru

Highlights: • Optimized conditions were determined for the production of rice straw pellets. • The moisture content and forming temperature are key factors. • High quality rice pellets in the lower heating value and durability were produced. - Abstract: A large amount of rice straw is generated and left as much in paddy fields, which causes greenhouse gas emissions as methane. Rice straw can be used as bioenergy. Rice straw pellets are a promising technology because pelletization of rice straw is a form of mass and energy densification, which leads to a product that is easy to handle, transport, storemore » and utilize because of the increase in the bulk density. The operational conditions required to produce high quality rice straw pellets have not been determined. This study determined the optimal moisture content range required to produce rice straw pellets with high yield ratio and high heating value, and also determined the influence of particle size and the forming temperature on the yield ratio and durability of rice straw pellets. The optimal moisture content range was between 13% and 20% under a forming temperature of 60 or 80 °C. The optimal particle size was between 10 and 20 mm, considering the time and energy required for shredding, although the particle size did not significantly affect the yield ratio and durability of the pellets. The optimized conditions provided high quality rice straw pellets with nearly 90% yield ratio, ⩾12 MJ/kg for the lower heating value, and >95% durability.« less

Critical moisture content for microbial growth in dried food-processing residues.

PubMed

Rezaei, Farzaneh; Vandergheynst, Jean S

2010-09-01

Food-processing residues are good feedstocks for biofuel and biochemical production because they have high energy content and are abundant. Year-round biofuel and biochemical production requires proper storage to prevent microbial decomposition and thermal runaway. In this study, microbial activity of tomato pomace (TP), grape pomace (GP), fermented grape pomace (FGP) and sugar beet pulp (SBP) was monitored at nine different moisture contents. Maximum and cumulative respirations for each feedstock with respect to moisture content followed a sigmoidal relationship. The critical moisture content below which no microbial activity was detected for SBP, TP, FGP and GP was 24-31, 16-21, 23-33 and 43-46% (dry basis) respectively. A logarithmic relationship was observed (R(2) = 0.94) between critical moisture content and initial water-soluble carbohydrate (WSC) content of the processing residues. The critical moisture content below which no microbial activity was detected and the relationship between critical moisture content and initial WSC content were determined in this study for four food-processing residues. Both parameters permit evaluation of the potential for deterioration of food-processing residues during storage based on moisture content and WSC content. Copyright 2010 Society of Chemical Industry.

Characterisation of chemical composition and energy content of green waste and municipal solid waste from Greater Brisbane, Australia.

PubMed

Hla, San Shwe; Roberts, Daniel

2015-07-01

The development and deployment of thermochemical waste-to-energy systems requires an understanding of the fundamental characteristics of waste streams. Despite Australia's growing interest in gasification of waste streams, no data are available on their thermochemical properties. This work presents, for the first time, a characterisation of green waste and municipal solid waste in terms of chemistry and energy content. The study took place in Brisbane, the capital city of Queensland. The municipal solid waste was hand-sorted and classified into ten groups, including non-combustibles. The chemical properties of the combustible portion of municipal solid waste were measured directly and compared with calculations made based on their weight ratios in the overall municipal solid waste. The results obtained from both methods were in good agreement. The moisture content of green waste ranged from 29% to 46%. This variability - and the tendency for soil material to contaminate the samples - was the main contributor to the variation of samples' energy content, which ranged between 7.8 and 10.7MJ/kg. The total moisture content of food wastes and garden wastes was as high as 70% and 60%, respectively, while the total moisture content of non-packaging plastics was as low as 2.2%. The overall energy content (lower heating value on a wet basis, LHVwb) of the municipal solid waste was 7.9MJ/kg, which is well above the World Bank-recommended value for utilisation in thermochemical conversion processes. Copyright © 2015 Elsevier Ltd. All rights reserved.

Agricultural soil moisture experiment, Colby, Kansas 1978: Measured and predicted hydrological properties of the soil

NASA Technical Reports Server (NTRS)

Arya, L. M. (Principal Investigator)

1980-01-01

Predictive procedures for developing soil hydrologic properties (i.e., relationships of soil water pressure and hydraulic conductivity to soil water content) are presented. Three models of the soil water pressure-water content relationship and one model of the hydraulic conductivity-water content relationship are discussed. Input requirements for the models are indicated, and computational procedures are outlined. Computed hydrologic properties for Keith silt loam, a soil typer near Colby, Kansas, on which the 1978 Agricultural Soil Moisture Experiment was conducted, are presented. A comparison of computed results with experimental data in the dry range shows that analytical models utilizing a few basic hydrophysical parameters can produce satisfactory data for large-scale applications.

[The stratification of moisture content and its dynamics in co-composting of sewage sludge and pig manure].

PubMed

Luo, Wei; Chen, Tong-bin; Gao, Ding; Zheng, Yu-qi; Zheng, Guo-di

2004-03-01

The experiment of co-composting of sewage sludge and pig manure was studied. The moisture contents were 50.82%-60.87% at the stage of temperature rising and 38.7%-52.17% at the stage of thermophilic fermentation, and the stratification of moisture content were not obvious for both stages because the door, the internal wall and the depth of the composting bay had little effect on the stratification. At the stage of cooling, the moisture content was 24.54%-49.39%, and the stratification of moisture content was remarkable as the door, the internal wall and the depth of the composting bay had great influence on it. At the stage of maturity, the moisture content was 19.18%-49.34%, and the stratification of moisture weakened, for which the door and the internal wall were mainly responsible. At the different composting stage, the degree of difference of moisture content on the profiles of the pile was of the order: maturity stage > cooling stage > thermophilic stage = temperature rising stage, and the moisture content in the pile was as follows: the lower > the middle > the upper. The relation between moisture content and composting time meeted with two-order kinetics equation.

A Portable Solid-State Moisture Meter For Agricultural And Food Products

NASA Astrophysics Data System (ADS)

Bull, C. R.; Stafford, J. V.; Weaving, G. S.

1988-10-01

This paper reports on the development of a small, robust, battery operated near infra-red (NIR) reflectance device, designed for rapid on-farm measurement of the moisture content of forage crops without prior sample preparation. It has potential application to other agricultural or food materials. The instrument is based on two light emitting diodes (LEDs), a germanium detector and a control CMOS single chip microcomputer. The meter has been calibrated to give a direct read out of moisture content for 4 common grass varieties at 3 stages of development. The accuracy of a single point measurement on a grass sample is approximately +/- 6% over a range of 40-80% (wet basis). However, the potential accuracy on a homogeous sample may be as goon as 0.15%.

Soil moisture variation patterns observed in Hand County, South Dakota

NASA Technical Reports Server (NTRS)

Jones, E. B.; Owe, M.; Schmugge, T. J. (Principal Investigator)

1981-01-01

Soil moisture data were taken during 1976 (April, June, October), 1977 (April, May, June), and 1978 (May, June, July) Hand County, South Dakota as part of the ground truth used in NASA's aircraft experiments to study the use of microwave radiometers for the remote sensing of soil moisture. The spatial variability observed on the ground during each of the sampling events was studied. The data reported are the mean gravimetric soil moisture contained in three surface horizon depths: 0 to 2.5, 0 to 5 and 0 to 10 cm. The overall moisture levels ranged from extremely dry conditions in June 1976 to very wet in May 1978, with a relatively even distribution of values within that range. It is indicated that well drained sites have to be partitioned from imperfectly drained areas when attempting to characterize the general moisture profile throughout an area of varying soil and cover type conditions. It is also found that the variability in moisture content is greatest in the 0 to 2.5 cm measurements and decreases as the measurements are integrated over a greater depth. It is also determined that the sampling intensity of 10 measurements per km is adequate to estimate the mean moisture with an uncertainty of + or - 3 percent under average moisture conditions in areas of moderate to good drainage.

7 CFR 51.2548 - Average moisture content determination.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Average moisture content determination. 51.2548... moisture content determination. (a) Determining average moisture content of the lot is not a requirement of... connection with grade analysis or as a separate determination. (b) Nuts shall be obtained from a randomly...

7 CFR 51.2561 - Average moisture content.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Average moisture content. 51.2561 Section 51.2561... STANDARDS) United States Standards for Grades of Shelled Pistachio Nuts § 51.2561 Average moisture content. (a) Determining average moisture content of the lot is not a requirement of the grades, except when...

Relationship between moisture content and electrical impedance of carrot slices during drying

NASA Astrophysics Data System (ADS)

Kertész, Ákos; Hlaváčová, Zuzana; Vozáry, Eszter; Staroňová, Lenka

2015-01-01

Electrical properties of food materials can give information about the inner structure and physiological state of biological tissues. Generally, the process of drying of fruits and vegetables is followed by weight loss. The aim of this study was to measure the impedance spectra of carrot slices during drying and to correlate impedance parameters to moisture content in different drying periods. Cylindrical slices were cut out from the carrot root along the axis. The slices were dried in a Venticell 111 air oven at 50°C. The weight of the slices was measured with a Denver SI-603 electronic analytical and precision balance. The weighing of the samples was performed every 30 min at the beginning of drying and every 60 min after the process. The moisture content of the samples was calculated on wet basis. The magnitude and phase angle of electrical impedance of the slices were measured with HP 4284A and 4285A precision LCR meters in the frequency range from 30 Hz to 1 MHz and from 75 kHz to 30 MHz, respectively, at voltage 1 V. The impedance measurement was performed after weighting. The change in the magnitude of impedance during drying showed a good correlation with the change in the moisture content.

Moisture sensor based on evanescent wave light scattering by porous sol-gel silica coating

DOEpatents

Tao, Shiquan; Singh, Jagdish P.; Winstead, Christopher B.

2006-05-02

An optical fiber moisture sensor that can be used to sense moisture present in gas phase in a wide range of concentrations is provided, as well techniques for making the same. The present invention includes a method that utilizes the light scattering phenomenon which occurs in a porous sol-gel silica by coating an optical fiber core with such silica. Thus, a porous sol-gel silica polymer coated on an optical fiber core forms the transducer of an optical fiber moisture sensor according to an embodiment. The resulting optical fiber sensor of the present invention can be used in various applications, including to sense moisture content in indoor/outdoor air, soil, concrete, and low/high temperature gas streams.

An experimental investigation of the smoldering combustion of cotton with different moisture contents

NASA Astrophysics Data System (ADS)

Li, Wendong; Liu, Wanfu; Ni, Zhaopeng; Wang, Lu; Gao, Bo

2018-03-01

Cotton is an inflammable substance that can be ignited by a weak ignition source. Since, cotton fiber is typically removed from cottonseed, compressed into bales and stored in the warehouse for extended periods of time, the moisture content is a very important characteristic of cotton. In this study, the effect of moisture content on cotton smoldering combustion was studied experimentally by characterizing cotton samples with different moisture contents. The results showed that the higher moisture content of cotton delayed the smoldering combustion process of cotton and prolonged the duration of high temperature of cotton smoldering. And we could find that when the moisture content is higher than 10%, the characteristics of smoldering change obviously.

An instrument for rapid, accurate, determination of fuel moisture content

Treesearch

Stephen S. Sackett

1980-01-01

Moisture contents of dead and living fuels are key variables in fire behavior. Accurate, real-time fuel moisture data are required for prescribed burning and wildfire behavior predictions. The convection oven method has become the standard for direct fuel moisture content determination. Efforts to quantify fuel moisture through indirect methods have not been...

Effect of stopper processing conditions on moisture content and ramifications for lyophilized products: comparison of "low" and "high" moisture uptake stoppers.

PubMed

Donovan, P D; Corvari, V; Burton, M D; Rajagopalan, N

2007-01-01

The purpose of this study was to evaluate the effect of processing and storage on the moisture content of two commercially available, 13-mm lyophilization stoppers designated as low moisture (LM) and high moisture (HM) uptake stoppers. The stopper moisture studies included the effect of steam sterilization time, drying time and temperature, equilibrium moisture content, lyophilization and moisture transfer from stopper to a model-lactose lyophilized cake. Results indicated that both stoppers absorbed significant amounts of moisture during sterilization and that the HM stopper absorbed significantly more water than the LM stopper. LM and HM stoppers required approximately 2 and 8 h drying at 105 degrees C, respectively, to achieve final moisture content of not more than 0.5 mg/stopper. Following drying, stopper moisture levels equilibrated rapidly to ambient storage conditions. The apparent equilibrium moisture level was approximately 7 times higher in the HM versus LM stopper. Freeze-drying had minimal effect on the moisture content of dried stoppers. Finally, moisture transfer from the stopper to the lyophilized product is dependent on the initial stopper water content and storage temperature. To better quantify the ramifications of stopper moisture, projections of moisture uptake over the shelf life of a drug product were calculated based on the product-contact surface area of stoppers. Attention to stopper storage conditions prior to use, in addition to processing steps, are necessary to minimize stability issues especially in low-fill, mass lyophilized products.

Water content estimated from point scale to plot scale

NASA Astrophysics Data System (ADS)

Akyurek, Z.; Binley, A. M.; Demir, G.; Abgarmi, B.

2017-12-01

Soil moisture controls the portioning of rainfall into infiltration and runoff. Here we investigate measurements of soil moisture using a range of techniques spanning different spatial scales. In order to understand soil water content in a test basin, 512 km2 in area, in the south of Turkey, a Cosmic Ray CRS200B soil moisture probe was installed at elevation of 1459 m and an ML3 ThetaProbe (CS 616) soil moisture sensor was established at 5cm depth used to get continuous soil moisture. Neutron count measurements were corrected for the changes in atmospheric pressure, atmospheric water vapour and intensity of incoming neutron flux. The calibration of the volumetric soil moisture was performed, from the laboratory analysis, the bulk density varies between 1.719 (g/cm3) -1.390 (g/cm3), and the dominant soil texture is silty clay loam and silt loamThe water content reflectometer was calibrated for soil-specific conditions and soil moisture estimates were also corrected with respect to soil temperature. In order to characterize the subsurface, soil electrical resistivity tomography was used. Wenner and Schlumberger array geometries were used with electrode spacing varied from 1m- 5 m along 40 m and 200 m profiles. From the inversions of ERT data it is apparent that within 50 m distance from the CRS200B, the soil is moderately resistive to a depth of 2m and more conductive at greater depths. At greater distances from the CRS200B, the ERT results indicate more resistive soils. In addition to the ERT surveys, ground penetrating radar surveys using a common mid-point configuration was used with 200MHz antennas. The volumetric soil moisture obtained from GPR appears to overestimate those based on TDR observations. The values obtained from CS616 (at a point scale) and CRS200B (at a mesoscale) are compared with the values obtained at a plot scale. For the field study dates (20-22.06.2017) the volumetric moisture content obtained from CS616 were 25.14%, 25.22% and 25.96% respectively. The values obtained from CRS200B were 23.23%, 22.81% and 23.26% for the same dates. Whereas the values obtained from GPR were between 32%-44%. Soil moisture observed by CRS200B is promising to monitor the water content in the soil at the mesoscale and ERT surveys help to understand the spatial variability of the soil water content within the footprint of CRS200B.

Fiberboard bending properties as a function of density, thickness, resin, and moisture content

Treesearch

John F. Hunt; Jane O' Dell; Chris Turk

2008-01-01

Fibers from treetop residues of lodgepole pine (Pinus contorta) and recycled old corrugated containers were used to fabricate wet-formed fiberboard panels over a range of densities from 300 to 1100 kg m-3, a thickness range from 1.3 to 4.8 mm, and phenolic resin contents from 0% to 4.5%. The panels were then tested after conditioning in 50% and 90% relative humidity (...

Moisture Sorption Isotherms and Properties of Sorbed Water of Neem ( Azadirichta indica A. Juss) Kernels

NASA Astrophysics Data System (ADS)

Ngono Mbarga, M. C.; Bup Nde, D.; Mohagir, A.; Kapseu, C.; Elambo Nkeng, G.

2017-01-01

A neem tree growing abundantly in India as well as in some regions of Asia and Africa gives fruits whose kernels have about 40-50% oil. This oil has high therapeutic and cosmetic qualities and is recently projected to be an important raw material for the production of biodiesel. Its seed is harvested at high moisture contents, which leads tohigh post-harvest losses. In the paper, the sorption isotherms are determined by the static gravimetric method at 40, 50, and 60°C to establish a database useful in defining drying and storage conditions of neem kernels. Five different equations are validated for modeling the sorption isotherms of neem kernels. The properties of sorbed water, such as the monolayer moisture content, surface area of adsorbent, number of adsorbed monolayers, and the percent of bound water are also defined. The critical moisture content necessary for the safe storage of dried neem kernels is shown to range from 5 to 10% dry basis, which can be obtained at a relative humidity less than 65%. The isosteric heats of sorption at 5% moisture content are 7.40 and 22.5 kJ/kg for the adsorption and desorption processes, respectively. This work is the first, to the best of our knowledge, to give the important parameters necessary for drying and storage of neem kernels, a potential raw material for the production of oil to be used in pharmaceutics, cosmetics, and biodiesel manufacturing.

Downscaling Satellite Data for Predicting Catchment-scale Root Zone Soil Moisture with Ground-based Sensors and an Ensemble Kalman Filter

NASA Astrophysics Data System (ADS)

Lin, H.; Baldwin, D. C.; Smithwick, E. A. H.

2015-12-01

Predicting root zone (0-100 cm) soil moisture (RZSM) content at a catchment-scale is essential for drought and flood predictions, irrigation planning, weather forecasting, and many other applications. Satellites, such as the NASA Soil Moisture Active Passive (SMAP), can estimate near-surface (0-5 cm) soil moisture content globally at coarse spatial resolutions. We develop a hierarchical Ensemble Kalman Filter (EnKF) data assimilation modeling system to downscale satellite-based near-surface soil moisture and to estimate RZSM content across the Shale Hills Critical Zone Observatory at a 1-m resolution in combination with ground-based soil moisture sensor data. In this example, a simple infiltration model within the EnKF-model has been parameterized for 6 soil-terrain units to forecast daily RZSM content in the catchment from 2009 - 2012 based on AMSRE. LiDAR-derived terrain variables define intra-unit RZSM variability using a novel covariance localization technique. This method also allows the mapping of uncertainty with our RZSM estimates for each time-step. A catchment-wide satellite-to-surface downscaling parameter, which nudges the satellite measurement closer to in situ near-surface data, is also calculated for each time-step. We find significant differences in predicted root zone moisture storage for different terrain units across the experimental time-period. Root mean square error from a cross-validation analysis of RZSM predictions using an independent dataset of catchment-wide in situ Time-Domain Reflectometry (TDR) measurements ranges from 0.060-0.096 cm3 cm-3, and the RZSM predictions are significantly (p < 0.05) correlated with TDR measurements [r = 0.47-0.68]. The predictive skill of this data assimilation system is similar to the Penn State Integrated Hydrologic Modeling (PIHM) system. Uncertainty estimates are significantly (p < 0.05) correlated to cross validation error during wet and dry conditions, but more so in dry summer seasons. Developing an EnKF-model system that downscales satellite data and predicts catchment-scale RZSM content is especially timely, given the anticipated release of SMAP surface moisture data in 2015.

[Detecting the moisture content of forest surface soil based on the microwave remote sensing technology.

PubMed

Li, Ming Ze; Gao, Yuan Ke; Di, Xue Ying; Fan, Wen Yi

2016-03-01

The moisture content of forest surface soil is an important parameter in forest ecosystems. It is practically significant for forest ecosystem related research to use microwave remote sensing technology for rapid and accurate estimation of the moisture content of forest surface soil. With the aid of TDR-300 soil moisture content measuring instrument, the moisture contents of forest surface soils of 120 sample plots at Tahe Forestry Bureau of Daxing'anling region in Heilongjiang Province were measured. Taking the moisture content of forest surface soil as the dependent variable and the polarization decomposition parameters of C band Quad-pol SAR data as independent variables, two types of quantitative estimation models (multilinear regression model and BP-neural network model) for predicting moisture content of forest surface soils were developed. The spatial distribution of moisture content of forest surface soil on the regional scale was then derived with model inversion. Results showed that the model precision was 86.0% and 89.4% with RMSE of 3.0% and 2.7% for the multilinear regression model and the BP-neural network model, respectively. It indicated that the BP-neural network model had a better performance than the multilinear regression model in quantitative estimation of the moisture content of forest surface soil. The spatial distribution of forest surface soil moisture content in the study area was then obtained by using the BP neural network model simulation with the Quad-pol SAR data.

Effect of Free-range Rearing on Meat Composition, Physical Properties and Sensory Evaluation in Taiwan Game Hens.

PubMed

Lin, Cheng-Yung; Kuo, Hsiao-Yun; Wan, Tien-Chun

2014-06-01

Experiments were conducted to evaluate the effect of an outdoor-grazed raising model on meat composition, physical properties and sensory attributes of Taiwan game hens. Six hundred 1-d old female chicks were raised on a floor for 8 weeks. On day 57, 600 healthy birds, with similar body weight, were selected and randomly assigned to three treatment groups (cage, floor-pen and free-range). The results showed that different feeding models had no effect on drip loss, cooking loss, moisture, crude protein, crude fat, crude ash, zinc and calorie contents in breast meat and moisture content in thigh meat. The free-range group had the lowest fat content in both breast and thigh meat, and the lowest calorie content in thigh meat. The firmness and toughness in both thigh and breast of the free-range group were the highest values (p<0.05). The crude protein, total collagen, zinc and iron contents in thigh meat and total collagen content in breast meat of the free-range group were significantly higher than those of the cage-feeding group (p<0.05). The meat sensory scores of flavor, chewiness and overall acceptability of both thigh and breast meat of the free-range group were significantly (p<0.05) better than those of the other two groups. Moreover, the current findings also indicate that the Taiwan game hens of the free-range feeding model displayed well-received carcass traits and meat quality, with higher scores for flavor, chewiness and overall acceptability for greater sensory satisfaction in both breast and thigh meat. In addition, the thigh meat contained high protein and total collage but low fat, offering a healthier diet choice.

Effect of Free-range Rearing on Meat Composition, Physical Properties and Sensory Evaluation in Taiwan Game Hens

PubMed Central

Lin, Cheng-Yung; Kuo, Hsiao-Yun; Wan, Tien-Chun

2014-01-01

Experiments were conducted to evaluate the effect of an outdoor-grazed raising model on meat composition, physical properties and sensory attributes of Taiwan game hens. Six hundred 1-d old female chicks were raised on a floor for 8 weeks. On day 57, 600 healthy birds, with similar body weight, were selected and randomly assigned to three treatment groups (cage, floor-pen and free-range). The results showed that different feeding models had no effect on drip loss, cooking loss, moisture, crude protein, crude fat, crude ash, zinc and calorie contents in breast meat and moisture content in thigh meat. The free-range group had the lowest fat content in both breast and thigh meat, and the lowest calorie content in thigh meat. The firmness and toughness in both thigh and breast of the free-range group were the highest values (p<0.05). The crude protein, total collagen, zinc and iron contents in thigh meat and total collagen content in breast meat of the free-range group were significantly higher than those of the cage-feeding group (p<0.05). The meat sensory scores of flavor, chewiness and overall acceptability of both thigh and breast meat of the free-range group were significantly (p<0.05) better than those of the other two groups. Moreover, the current findings also indicate that the Taiwan game hens of the free-range feeding model displayed well-received carcass traits and meat quality, with higher scores for flavor, chewiness and overall acceptability for greater sensory satisfaction in both breast and thigh meat. In addition, the thigh meat contained high protein and total collage but low fat, offering a healthier diet choice. PMID:25050027

Effect of drying and frying conditions on physical and chemical characteristics of fish maw from swim bladder of seabass (Lates calcarifer).

PubMed

Sinthusamran, Sittichoke; Benjakul, Soottawat

2015-12-01

Swim bladder is generated as a by-product during evisceration. It has been used for the production of fish maw, in which several processing parameters determine the characteristics or quality of the resulting fish maw. The present study aimed to investigate the characteristics of fish maws from seabass swim bladder as influenced by drying and frying conditions. The expansion ratio and oil uptake content of fish maw increased as the moisture content of swim bladder increased (P < 0.05). Nevertheless, the expansion ratio of fish maw decreased when the moisture content was higher than 150 g kg(-1) . The L*-value decreased, whilst the a*- and b*-values of fish maw increased with increasing moisture content. When pre-frying and frying temperatures increased, the expansion ratio of fish maw increased (P < 0.05). However, the expansion ratio decreased when the frying was performed at a temperature higher than 200 °C. The oil uptake contents of fish maw with frying temperatures of 180 and 200 °C were in the range of 451.06-578.06 g kg(-1) , whereas the lower contents (378.60-417.17 g kg(-1) ) were found in those having frying temperatures of 220-240 °C. Hardness of fish maw decreased but no changes in fracturability were observed with increasing pre-frying temperature when subsequent frying was carried out 200 °C. Drying temperatures, moisture content, pre-frying and frying temperatures were the factors influencing the characteristics and properties of fish maws from seabass swim bladder. Fish maw could be prepared by pre-frying swim bladder, dried at 60 °C to obtain 150 g kg(-1) moisture content, at 110 °C for 5 min, followed by frying at 200 °C for 20 s. © 2014 Society of Chemical Industry.

Decomposition of soil organic matter from boreal black spruce forest: Environmental and chemical controls

USGS Publications Warehouse

Wickland, K.P.; Neff, J.C.

2008-01-01

Black spruce forests are a dominant covertype in the boreal forest region, and they inhabit landscapes that span a wide range of hydrologic and thermal conditions. These forests often have large stores of soil organic carbon. Recent increases in temperature at northern latitudes may be stimulating decomposition rates of this soil carbon. It is unclear, however, how changes in environmental conditions influence decomposition in these systems, and if substrate controls of decomposition vary with hydrologic and thermal regime. We addressed these issues by investigating the effects of temperature, moisture, and organic matter chemical characteristics on decomposition of fibric soil horizons from three black spruce forest sites. The sites varied in drainage and permafrost, and included a "Well Drained" site where permafrost was absent, and "Moderately well Drained" and "Poorly Drained" sites where permafrost was present at about 0.5 m depth. Samples collected from each site were incubated at five different moisture contents (2, 25, 50, 75, and 100% saturation) and two different temperatures (10??C and 20??C) in a full factorial design for two months. Organic matter chemistry was analyzed using pyrolysis gas chromatography-mass spectrometry prior to incubation, and after incubation on soils held at 20??C, 50% saturation. Mean cumulative mineralization, normalized to initial carbon content, ranged from 0.2% to 4.7%, and was dependent on temperature, moisture, and site. The effect of temperature on mineralization was significantly influenced by moisture content, as mineralization was greatest at 20??C and 50-75% saturation. While the relative effects of temperature and moisture were similar for all soils, mineralization rates were significantly greater for samples from the "Well Drained" site compared to the other sites. Variations in the relative abundances of polysaccharide-derivatives and compounds of undetermined source (such as toluene, phenol, 4-methyl phenol, and several unidentifiable compounds) could account for approximately 44% of the variation in mineralization across all sites under ideal temperature and moisture conditions. Based on our results, changes in temperature and moisture likely have similar, additive effects on in situ soil organic matter (SOM) decomposition across a wide range of black spruce forest systems, while variations in SOM chemistry can lead to significant differences in decomposition rates within and among forest sites. ?? 2007 Springer Science+Business Media B.V.

Characterization of friction and moisture of porcine lingual tissue in vitro in response to artificial saliva and mouthwash solutions.

PubMed

Zundel, J; Ansari, S A; Trivedi, H M; Masters, J G; Mascaro, S

2018-05-07

The purpose of this research is to characterize the effects of mouthwash solutions on oral friction and moisture using a quantitative in vitro approach. The frictional coefficient of in vitro porcine tongue samples was measured using a magnetic levitation haptic device equipped with a custom tactor designed to mimic human skin. A commercially available moisture meter was used to measure moisture content of the samples. Tongue samples were first tested before treatment, then after application of saliva (either human or artificial), and again after application of 1 of 11 different mouthwash solutions. The data indicate that the samples treated with artificial saliva vs real saliva have comparable friction coefficient and moisture content. Furthermore, the moisture and friction coefficient remain relatively constant for up to 60 minutes after exposure to ambient conditions. Samples treated with artificial saliva have an average friction coefficient in the range of 0.70-0.80. Application of mouthwash solutions produced an average friction coefficient of 0.39-0.49 but retained the high moisture content of the artificial salivary layer. Several mouthwash solutions resulted in statistically significant differences in the friction coefficient relative to each other. The results of this study demonstrate that a magnetic levitation device can be an effective tool for in vitro oral tribology and that artificial saliva is an effective substitute for real saliva in extended in vitro experiments. The application of mouthwash generally reduces the coefficient of friction of the tongue samples while preserving a relatively high moisture level, and some mouthwashes reduce friction significantly more than others. © 2018 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Estimating moisture content of tree-length roundwood

Treesearch

Alexander Clark; Richard F. Daniels

2000-01-01

The green weight of southern pine tree-length roundwood delivered to the pulp mill is generally known. However, for optimum mill efficiency it is desirable to know dry weight. The moisture content of tree-length pine logs is quite variable. The moisture content of pine tree-length logs increases significantly with increasing stem height. Moisture content also varies...

46 CFR 164.009-19 - Measurement of moisture and volatile matter content.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 6 2012-10-01 2012-10-01 false Measurement of moisture and volatile matter content. 164... Vessels § 164.009-19 Measurement of moisture and volatile matter content. (a) The measurements described in this section are made to determine the moisture and volatile matter content of a sample. (b) A...

46 CFR 164.009-19 - Measurement of moisture and volatile matter content.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 6 2013-10-01 2013-10-01 false Measurement of moisture and volatile matter content. 164... Vessels § 164.009-19 Measurement of moisture and volatile matter content. (a) The measurements described in this section are made to determine the moisture and volatile matter content of a sample. (b) A...

46 CFR 164.009-19 - Measurement of moisture and volatile matter content.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Measurement of moisture and volatile matter content. 164... Vessels § 164.009-19 Measurement of moisture and volatile matter content. (a) The measurements described in this section are made to determine the moisture and volatile matter content of a sample. (b) A...

46 CFR 164.009-19 - Measurement of moisture and volatile matter content.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 6 2014-10-01 2014-10-01 false Measurement of moisture and volatile matter content. 164... Vessels § 164.009-19 Measurement of moisture and volatile matter content. (a) The measurements described in this section are made to determine the moisture and volatile matter content of a sample. (b) A...

46 CFR 164.009-19 - Measurement of moisture and volatile matter content.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 6 2011-10-01 2011-10-01 false Measurement of moisture and volatile matter content. 164... Vessels § 164.009-19 Measurement of moisture and volatile matter content. (a) The measurements described in this section are made to determine the moisture and volatile matter content of a sample. (b) A...

Soil moisture by extraction and gas chromatography

NASA Technical Reports Server (NTRS)

Merek, E. L.; Carle, G. C.

1973-01-01

To determine moisture content of soils rapidly and conveniently extract moisture with methanol and determine water content of methanol extract by gas chromatography. Moisture content of sample is calculated from weight of water and methanol in aliquot and weight of methanol added to sample.

Aflatoxins and ochratoxin a reduction in black and white pepper by gamma radiation

NASA Astrophysics Data System (ADS)

Jalili, M.; Jinap, S.; Noranizan, M. A.

2012-11-01

Irradiation is an important means of decontamination of food commodities, especially spices. The aim of the current study was to investigate the efficacy of gamma radiation (60Co) for decontaminating ochratoxin A (OTA) and aflatoxins B1 (AFB1), B2 (AFB2), G1 (AFG1) and G2 (AFG2) residues in artificially contaminated black and white pepper samples. The moisture content of the pepper samples was set at 12% or 18%, and the applied gamma dose ranged from 5 to 30 kGy. Mycotoxin levels were determined by high-performance liquid chromatography (HPLC) after immunoaffinity column (IAC) chromatography. Both the gamma irradiation dose and moisture content showed significant effects (P<0.05) on mycotoxin reduction. The maximum toxin reductions, found at 18% moisture content and 30 kGy, were 55.2%, 50.6%, 39.2%, 47.7% and 42.9% for OTA, AFB1, AFB2, AFG1 and AFG2, respectively.

Moisture content and its impact on aflatoxin levels in ready-to-use red chillies.

PubMed

Sahar, Najmus; Arif, Saqib; Iqbal, Sajid; Afzal, Qurat Ul Ain; Aman, Sahar; Ara, Jahan; Ahmed, Mubarik

2015-01-01

Moisture content (MC) and aflatoxin contamination were analysed to determine Red Chilli quality. A wide range (9.1-19.8%) of MC with a mean value of 11.4 ± 2.4% was found. Of 116 chilli samples, about 37% had low MC (<10%), 29.4% had medium-low MC (10-12%), 18.9% had medium-high MC (12 < MC < 14%) and 14.7% were above 14%. These four chilli groups had average aflatoxin levels of 2.1 ± 1.1, 5.3 ± 4.2, 8.9 ± 5.9 and 37 ± 20 µg/Kg, respectively. A direct relationship between moisture and aflatoxin content was found. The data best fitted a polynomial trend (R² = 0.89). The obtained equation could be utilised to assess aflatoxin levels based on MC. This study highlights the importance of using properly dried chillies with low MC, that is, ≤10%, to minimise health hazards associated with aflatoxin contamination.

A multi-frequency radiometric measurement of soil moisture content over bare and vegetated fields

NASA Technical Reports Server (NTRS)

Wang, J. R.; Schmugge, T. J.; Mcmurtrey, J. E., III; Gould, W. I.; Glazar, W. S.; Fuchs, J. E. (Principal Investigator)

1981-01-01

A USDA Beltsville Agricultural Research Center site was used for an experiment in which soil moisture remote sensing over bare, grass, and alfalfa fields was conducted over a three-month period using 0.6 GHz, 1.4 GHz, and 10.6 GHz Dicke-type microwave radiometers mounted on mobile towers. Ground truth soil moisture content and ambient air and sil temperatures were obtained concurrently with the radiometric measurements. Biomass of the vegetation cover was sampled about once a week. Soil density for each of the three fields was measured several times during the course of the experiment. Results of the radiometric masurements confirm the frequency dependence of moisture sensing sensitivity reduction reported earlier. Observations over the bare, wet field show that the measured brightness temperature is lowest at 5.0 GHz and highest of 0.6 GHz frequency, a result contrary to expectation based on the estimated dielectric permittivity of soil water mixtures and current radiative transfer model in that frequency range.

Optimization of parameters for enhanced oil recovery from enzyme treated wild apricot kernels.

PubMed

Rajaram, Mahatre R; Kumbhar, Baburao K; Singh, Anupama; Lohani, Umesh Chandra; Shahi, Navin C

2012-08-01

Present investigation was undertaken with the overall objective of optimizing the enzymatic parameters i.e. moisture content during hydrolysis, enzyme concentration, enzyme ratio and incubation period on wild apricot kernel processing for better oil extractability and increased oil recovery. Response surface methodology was adopted in the experimental design. A central composite rotatable design of four variables at five levels was chosen. The parameters and their range for the experiments were moisture content during hydrolysis (20-32%, w.b.), enzyme concentration (12-16% v/w of sample), combination of pectolytic and cellulolytic enzyme i.e. enzyme ratio (30:70-70:30) and incubation period (12-16 h). Aspergillus foetidus and Trichoderma viride was used for production of crude enzyme i.e. pectolytic and cellulolytic enzyme respectively. A complete second order model for increased oil recovery as the function of enzymatic parameters fitted the data well. The best fit model for oil recovery was also developed. The effect of various parameters on increased oil recovery was determined at linear, quadric and interaction level. The increased oil recovery ranged from 0.14 to 2.53%. The corresponding conditions for maximum oil recovery were 23% (w.b.), 15 v/w of the sample, 60:40 (pectolytic:cellulolytic), 13 h. Results of the study indicated that incubation period during enzymatic hydrolysis is the most important factor affecting oil yield followed by enzyme ratio, moisture content and enzyme concentration in the decreasing order. Enzyme ratio, incubation period and moisture content had insignificant effect on oil recovery. Second order model for increased oil recovery as a function of enzymatic hydrolysis parameters predicted the data adequately.

[Effect of moisture content on anaerobic methanization of municipal solid waste].

PubMed

Qu, Xian; He, Pin-Jing; Shao, Li-Ming; Bouchez, Théodore

2009-03-15

Biogas production, gas and liquid characteristics were investigated for comparing the effect of moisture content on methanization process of MSW with different compositions of food waste and cellulosic waste. Batch reactors were used to study the anaerobic methanization of typical Chinese and French municipal solid waste (MSW) and cellulosic waste with different moisture content, as 35%, field capacity (65%-70%), 80%, and saturated state (> 95%). The results showed that for the typical Chinese and French waste, which contained putrescible waste, the intermediate product, VFA, was diluted by high content of water, which helped to release the VFA inhibition on hydrolysis and methanization. Mass amount of methane was produced only when the moisture content of typical French waste was higher than 80%, while higher content of moisture was needed when the content of putrescible waste was higher in MSW, as > 95% for typical Chinese waste. Meanwhile the methane production rate and the ultimate cumulated methane production were increased when moisture content was leveled up. The ultimate cumulated methane production of the typical French waste with saturated state was 0.6 times higher than that of the waste with moisture content of 80%. For cellulosic waste, high moisture content of cellulosic materials contributed to increase the attachment area of microbes and enzyme on the surface of the materials, which enhance the waste hydrolysis and methanization. When the moisture content of the cellulosic materials increased from field capacity (65%) to saturated state (> 95%), the ultimate cumulated methane production increased for 3.8 times.

Moisture Management for High R-Value Walls

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lepage, R.; Schumacher, C.; Lukachko, A.

2013-11-01

The following report explains the moisture-related concerns for High R-value wall assemblies and discusses past Building America research work that informs this study. Hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones (2, 3, 4C, 4, 5A, and 7, respectively). The simulations are informed by experience gained from past research in this area and validated by field measurement and forensic experience. The modeling program was developed to assess the moisture durability of the wall assemblies based on threemore » primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage. The peak annual moisture content of the wood based exterior sheathing was used to comparatively analyze the response to the moisture loads for each of the walls in each given city. Walls which experienced sheathing moisture contents between 20% and 28% were identified as risky, whereas those exceeding 28% were identified as very high risk. All of the wall assemblies perform well under idealized conditions. However, only the walls with exterior insulation, or cavity insulation which provides a hygrothermal function similar to exterior insulation, perform adequately when exposed to moisture loads. Walls with only cavity insulation are particularly susceptible to air leakage condensation. None of the walls performed well when a precipitation based bulk water leak was introduced to the backside of the sheathing, emphasizing the importance of proper flashing details.« less

Moisture Management of High-R Walls (Fact Sheet)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

2013-12-01

The following report explains the moisture-related concerns for High R-value wall assemblies and discusses past Building America research work that informs this study. Hygrothermal simulations were prepared for several common approaches to High R-value wall construction in six cities (Houston, Atlanta, Seattle, St. Louis, Chicago, and International Falls) representing a range of climate zones (2, 3, 4C, 4, 5A, and 7, respectively). The simulations are informed by experience gained from past research in this area and validated by field measurement and forensic experience. The modeling program was developed to assess the moisture durability of the wall assemblies based on threemore » primary sources of moisture: construction moisture, air leakage condensation, and bulk water leakage. The peak annual moisture content of the wood based exterior sheathing was used to comparatively analyze the response to the moisture loads for each of the walls in each given city. Walls which experienced sheathing moisture contents between 20% and 28% were identified as risky, whereas those exceeding 28% were identified as very high risk. All of the wall assemblies perform well under idealized conditions. However, only the walls with exterior insulation, or cavity insulation which provides a hygrothermal function similar to exterior insulation, perform adequately when exposed to moisture loads. Walls with only cavity insulation are particularly susceptible to air leakage condensation. None of the walls performed well when a precipitation based bulk water leak was introduced to the backside of the sheathing, emphasizing the importance of proper flashing details.« less

Frequency, moisture content, and temperature dependent dielectric properties of potato starch related to drying with radio-frequency/microwave energy.

PubMed

Zhu, Zhuozhuo; Guo, Wenchuan

2017-08-24

To develop advanced drying methods using radio-frequency (RF) or microwave (MW) energy, dielectric properties of potato starch were determined using an open-ended coaxial-line probe and network analyzer at frequencies between 20 and 4,500 MHz, moisture contents between 15.1% and 43.1% wet basis (w.b.), and temperatures between 25 and 75 °C. The results showed that both dielectric constant (ε') and loss factor (ε″) were dependent on frequency, moisture content, and temperature. ε' decreased with increasing frequency at a given moisture content or temperature. At low moisture contents (≤25.4% w.b.) or low temperatures (≤45 °C), ε″ increased with increasing frequency. However, ε″ changed from decrease to increase with increasing frequency at high moisture contents or temperatures. At low temperatures (25-35 °C), both ε' and ε″ increased with increasing moisture content. At low moisture contents (15.1-19.5% w.b.), they increased with increasing temperature. The change trends of ε' and ε″ were different and dependent on temperature and moisture content at their high levels. The penetration depth (d p ) decreased with increasing frequency. RF treatments may provide potential large-scale industrial drying application for potato starch. This research offers useful information on dielectric properties of potato starch related to drying with electromagnetic energy.

Determination of the moisture content in the fluoride oxide fluxes of electroslag remelting

NASA Astrophysics Data System (ADS)

Vdovin, K. N.; Feoktistov, N. A.; Pivovarova, K. G.; Deryabin, D. A.

2016-12-01

ANF-32 flux has been studied with regard to the moisture content both after storage and upon operation. A simple and reliable procedure for the determination of the moisture content in ESR fluxes is proposed, and recommendations are given on monitoring the moisture content in calcined fluxes. The main sources of crystallization water of hydration are hydrogen sources.

Effect of moisture content on strength of CCA-treated lumber

Treesearch

Jerrold E. Winandy

1995-01-01

Recent studies on the effects of chromated copper arsenate (CCA) treatment on lumber design properties have primarily evaluated the effects of such treatment at or near 12% moisture content and at failure times of 1 to 10 min. The influence of various moisture contents and faster loading rates is unknown. This report discusses the influence of moisture content and its...

Understanding the bias between moisture content by oven drying and water content by Karl Fischer titration at moisture equilibrium

USDA-ARS?s Scientific Manuscript database

Multiple causes of the difference between equilibrium moisture and water content have been found. The errors or biases were traced to the oven drying procedure to determine moisture content. The present paper explains the nature of the biases in oven drying and how it is possible to suppress one ...

Buildup Index as an Expression of Moisture Content in Duff

Treesearch

Von J. Johnson

1968-01-01

The relation between Buildup index and moisture content of grouped litter and duff samples from beneath four medium-site forest stands closely approximated the relation between Buildup index and moisture equivalent of 5-day timelag fuels having an equilibrium moisture content of 15 percent

The moisture content of ponderosa pine and whiteleaf manzanita foliage in the Central Sierra Nevada

Treesearch

Charles W. Philpot

1963-01-01

In the first year of studies of moisture in living fuels, pine and manzanita had dissimilar moisture trends, the moisture content of brush varied with elevation during the growing season, and soil moisture was correlated with brush foliage moisture.

The influence of temperature and moisture contents regimes on the aerobic microbial activity of a biosolids composting blend.

PubMed

Liang, C; Das, K C; McClendon, R W

2003-01-01

To understand the relationships between temperature, moisture content, and microbial activity during the composting of biosolids (municipal wastewater treatment sludge), well-controlled incubation experiments were conducted using a 2-factor factorial design with six temperatures (22, 29, 36, 43, 50, and 57 degrees C) and five moisture contents (30, 40, 50, 60, and 70%). The microbial activity was measured as O2 uptake rate (mg g(-1) h(-1)) using a computer controlled respirometer. In this study, moisture content proved to be a dominant factor impacting aerobic microbial activity of the composting blend. Fifty percent moisture content appeared to be the minimal requirement for obtaining activities greater than 1.0 mg g(-1) h(-1). Temperature was also documented to be an important factor for biosolids composting. However, its effect was less influential than moisture content. Particularly, the enhancement of composting activities induced by temperature increment could be realized by increasing moisture content alone.

The effect of moisture content on physicochemical properties of extruded waxy and non-waxy rice flour.

PubMed

Jongsutjarittam, Ornpicha; Charoenrein, Sanguansri

2014-12-19

The properties of waxy rice flour (WRF) and non-waxy rice flour (RF) were modified using an extrusion process with different feeding material moisture contents. WRF was more affected by the thermomechanical stress from extrusion; consequently, it had a lower glass transition temperature but higher water solubility index (WSI) indicating higher molecular degradation than extruded RF. The lower moisture content of the feeding flour caused more severe flour damage (coarser surface of the extruded flour) and lowered relative crystallinity compared to higher moisture content processing. Moreover, low moisture content processing led to complete gelatinization, whereas, partial gelatinization occurred in the higher moisture content extrusion. Consequently, the extruded flours had a lower peak viscosity and gelatinization enthalpy but a higher water absorption index and WSI than native flour. In conclusion, the rice flour type and the moisture content of the extrusion feeding flour affected the physicochemical properties of the extruded flour. Copyright © 2014 Elsevier Ltd. All rights reserved.

Soil moisture influence on the interannual variation in temperature sensitivity of soil organic carbon mineralization in the Loess Plateau

NASA Astrophysics Data System (ADS)

Zhang, Y. J.; Guo, S. L.; Zhao, M.; Du, L. L.; Li, R. J.; Jiang, J. S.; Wang, R.; Li, N. N.

2015-06-01

Temperature sensitivity of soil organic carbon (SOC) mineralization (i.e., Q10) determines how strong the feedback from global warming may be on the atmospheric CO2 concentration; thus, understanding the factors influencing the interannual variation in Q10 is important for accurately estimating local soil carbon cycle. In situ SOC mineralization rate was measured using an automated CO2 flux system (Li-8100) in long-term bare fallow soil in the Loess Plateau (35°12' N, 107°40' E) in Changwu, Shaanxi, China from 2008 to 2013. The results showed that the annual cumulative SOC mineralization ranged from 226 to 298 g C m-2 yr-1, with a mean of 253 g C m-2 yr-1 and a coefficient of variation (CV) of 13%, annual Q10 ranged from 1.48 to 1.94, with a mean of 1.70 and a CV of 10%, and annual soil moisture content ranged from 38.6 to 50.7% soil water-filled pore space (WFPS), with a mean of 43.8% WFPS and a CV of 11%, which were mainly affected by the frequency and distribution of precipitation. Annual Q10 showed a quadratic correlation with annual mean soil moisture content. In conclusion, understanding of the relationships between interannual variation in Q10, soil moisture, and precipitation are important to accurately estimate the local carbon cycle, especially under the changing climate.

Thermophysical properties of hydrophobised lime plaster - Experimental analysis of moisture effect

NASA Astrophysics Data System (ADS)

Pavlíková, Milena; Pernicová, Radka; Pavlík, Zbyšek

2016-07-01

Lime plasters are the most popular finishing materials in renewal of historical buildings and culture monuments. Because of their limited durability, new materials and design solutions are investigated in order to improve plasters performance in harmful environmental conditions. For the practical use, the plasters mechanical resistivity and the compatibility with substrate are the most decisive material parameters. However, also plasters hygric and thermal parameters affecting the overall hygrothermal function of the renovated structures are of the particular importance. On this account, the effect of moisture content on the thermophysical properties of a newly designed lime plasters containing hydrophobic admixture is analysed in the paper. For the comparative purposes, the reference lime and cement-lime plasters are tested as well. Basic characterization of the tested materials is done using bulk density, matrix density, and porosity measurements. Thermal conductivity and volumetric heat capacity in the broad range of moisture content are experimentally accessed using a transient impulse method. The obtained data reveals the significant increase of the both studied thermal parameters with increasing moisture content and gives information on plasters behaviour in a highly humid environment and/or in the case of their possible direct contact with liquid water. The accessed material parameters will be stored in a material database, where can find use as an input data for computational modelling of coupled heat and moisture transport in this type of porous building materials.

Fiber moisture content measurements of lint and seed cotton by a small microwave instrument

USDA-ARS?s Scientific Manuscript database

The timely and accurate measurement of cotton fiber moisture content is important, as deviations in moisture fiber content can impact the fiber quality and processing of cotton fiber. The Mesdan Aqualab is a small, modular, microwave-based fiber moisture measurement instrument for samples with mode...

Feasibility study of prompt gamma neutron activation for NDT measurement of moisture in stone and brick

DOE Office of Scientific and Technical Information (OSTI.GOV)

Livingston, R. A.; Al-Sheikhly, M.; Grissom, C.

2014-02-18

The conservation of stone and brick architecture or sculpture often involves damage caused by moisture. The feasibility of a NDT method based on prompt gamma neutron activation (PGNA) for measuring the element hydrogen as an indication of water is being evaluated. This includes systematic characterization of the lithology and physical properties of seven building stones and one brick type used in the buildings of the Smithsonian Institution in Washington, D.C. To determine the required dynamic range of the NDT method, moisture-related properties were measured by standard methods. Cold neutron PGNA was also used to determine chemically bound water (CBW) content.more » The CBW does not damage porous masonry, but creates an H background that defines the minimum level of detection of damaging moisture. The CBW was on the order of 0.5% for all the stones. This rules out the measurement of hygric processes in all of the stones and hydric processed for the stones with fine scale pore-size distributions The upper bound of moisture content, set by porosity through water immersion, was on the order of 5%. The dynamic range is about 10–20. The H count rates were roughly 1–3 cps. Taking into account differences in neutron energies and fluxes and sample volume between cold PGNA and a portable PGNA instrument, it appears that it is feasible to apply PGNA in the field.« less

Determining the frequency, depth and velocity of preferential flow by high frequency soil moisture monitoring

NASA Astrophysics Data System (ADS)

Hardie, Marcus; Lisson, Shaun; Doyle, Richard; Cotching, William

2013-01-01

Preferential flow in agricultural soils has been demonstrated to result in agrochemical mobilisation to shallow ground water. Land managers and environmental regulators need simple cost effective techniques for identifying soil - land use combinations in which preferential flow occurs. Existing techniques for identifying preferential flow have a range of limitations including; often being destructive, non in situ, small sampling volumes, or are subject to artificial boundary conditions. This study demonstrated that high frequency soil moisture monitoring using a multi-sensory capacitance probe mounted within a vertically rammed access tube, was able to determine the occurrence, depth, and wetting front velocity of preferential flow events following rainfall. Occurrence of preferential flow was not related to either rainfall intensity or rainfall amount, rather preferential flow occurred when antecedent soil moisture content was below 226 mm soil moisture storage (0-70 cm). Results indicate that high temporal frequency soil moisture monitoring may be used to identify soil type - land use combinations in which the presence of preferential flow increases the risk of shallow groundwater contamination by rapid transport of agrochemicals through the soil profile. However use of high frequency based soil moisture monitoring to determine agrochemical mobilisation risk may be limited by, inability to determine the volume of preferential flow, difficulty observing macropore flow at high antecedent soil moisture content, and creation of artificial voids during installation of access tubes in stony soils.

Soil moisture changes in two experimental sites in Eastern Spain. Irrigation versus rainfed orchards under organic farming

NASA Astrophysics Data System (ADS)

Azorin-Molina, Cesar; Vicente-Serrano, Sergio M.; Cerdà, Artemi

2013-04-01

Within the Soil Erosion and Degradation Research Group Experimental Stations, soil moisture is being researched as a key factor of the soil hydrology and soil erosion (Cerdà, 1995; Cerda, 1997; Cerdà 1998). This because under semiarid conditions soil moisture content plays a crucial role for agriculture, forest, groundwater recharge and soil chemistry and scientific improvement is of great interest in agriculture, hydrology and soil sciences. Soil moisture has been seeing as the key factor for plant photosynthesis, respiration and transpiration in orchards (Schneider and Childers, 1941) and plant growth (Veihmeyer and Hendrickson, 1950). Moreover, soil moisture determine the root growth and distribution (Levin et al., 1979) and the soil respiration ( Velerie and Orchard, 1983). Water content is expressed as a ratio, ranging from 0 (dry) to the value of soil porosity at saturation (wet). In this study we present 1-year of soil moisture measurements at two experimental sites in the Valencia region, Eastern Spain: one representing rainfed orchard typical from the Mediterranean mountains (El Teularet-Sierra de Enguera), and a second site corresponding to an irrigated orange crop (Alcoleja). The EC-5 soil moisture smart sensor S-SMC-M005 integrated with the field-proven ECH2O™ Sensor and a 12-bit A/D has been choosen for measuring soil water content providing ±3% accuracy in typical soil conditions. Soil moisture measurements were carried out at 5-minute intervals from January till December 2012. In addition, soil moisture was measured at two depths in each landscape: 2 and 20 cm depth - in order to retrieve a representative vertical cross-section of soil moisture. Readings are provided directly from 0 (dry) to 0.450 m3/m3 (wet) volumetric water content. The soil moisture smart sensor is conected to a HOBO U30 Station - GSM-TCP which also stored 5-minute temperature, relative humidity, dew point, global solar radiation, precipitation, wind speed and wind direction data. These complementary atmospheric measurements will serve to explain the intraannual and vertical variations observed in the soil moisture content in both experimental landscapes. This kind of study is aimed to understand the soil moisture content in two different environments such as irrigated rainfed orchards in a semi-arid region. For instance, these measurements have a direct impact on water availability for crops, plant transpiration and could have practical applications to schedule irrigation. Additionally, soil water content has also implications for erosion processes. Key Words: Water, Agriculture, Irrigation, Eastern Spain, Citrus. Acknowledgements The research projects GL2008-02879/BTE and LEDDRA 243857 supported this research. References Cerdà, A. 1995. Soil moisture regime under simulated rainfall in a three years abandoned field in Southeast Spain. Physics and Chemistry of The Earth, 20 (3-4), 271-279. Cerdà, A. 1997. Seasonal Changes of the Infiltration Rates in a Typical Mediterranean Scrubland on Limestone in Southeast Spain. Journal of Hydrology, 198 (1-4) 198-209 Cerdà, A. 1998. Effect of climate on surface flow along a climatological gradient in Israel. A field rainfall simulation approach. Journal of Arid Environments, 38, 145-159. Levin, I., Assaf, R., and Bravdo, B. 1979. Soil moisture and root distribution in an apple orchard irrigated by tricklers. Plant and Soil, 52, 31-40. Schneider, G. W. And Childers, N.F. 1941. Influence of soil moisture on photosynthesis, respiration and transpiration of apples leaves. Plant Physiol., 16, 565-583. Valerie, A. and Orchard, F.J. Cook. 1983. Relationship between soil respiration and soil moisture. Soil Biology and Biochemistry, 15, 447-453. Veihmeyer, F. J. and Hendrickson, A. H. 1950. Soil Moisture in Relation to Plant Growth. Annual Review of Plant Physiology, 1, 285-304.

The influence of moisture content variation on fungal pigment formation in spalted wood

PubMed Central

2012-01-01

Eight fungal species known to produce wood pigmentation were tested for reaction to various moisture contents in two hardwood species. Fungal pigmentation by Trametes versicolor and Xylaria polymorpha was stimulated at low water concentrations in both Acer saccharum (sugar maple) and Fagus grandifolia (American beech), while Inonotus hispidus and Polyporus squamosus were stimulated above 22-28% and 34-38% moisture content in beech and in sugar maple respectively. Fomes fomentarius and Polyporus brumalis produced maximum pigmentation in beech at 26 - 41% and in sugar maple at 59 - 96% moisture content. The pink staining Scytalidium cuboideum pigmented both wood species at above 35% moisture content. This research indicates that controlling the moisture content values of wood substrates can stimulate the intensity of pigmentation of specific fungi when spalting wood for decorative and commercial purpose. PMID:23245292

Study of heat-moisture treatment of potato starch granules by chemical surface gelatinization.

PubMed

Bartz, Josiane; da Rosa Zavareze, Elessandra; Dias, Alvaro Renato Guerra

2017-08-01

Native potato starch was subjected to heat-moisture treatment (HMT) at 12%, 15%, 18%, 21%, and 24% of moisture content at 110 °C for 1 h, and the effects on morphology, structure, and thermal and physicochemical properties were investigated. To reveal the internal structure, 30% and 50% of the granular surface were removed by chemical surface gelatinization in concentrated LiCl solution. At moisture contents of 12% and 15%, HTM reduced the gelatinization temperatures and relative crystallinity of the starches, while at moisture contents of 21% and 24 % both increased. The alterations on morphology, X-ray pattern, physicochemical properties, and increase of amylose content were more intense with the increase of moisture content of HMT. The removal of granular layers showed that the changes promoted by HMT occur throughout the whole granule and were pronounced at the core or peripheral region, depending of the moisture content applied during HMT. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Computer simulation of a space SAR using a range-sequential processor for soil moisture mapping

NASA Technical Reports Server (NTRS)

Fujita, M.; Ulaby, F. (Principal Investigator)

1982-01-01

The ability of a spaceborne synthetic aperture radar (SAR) to detect soil moisture was evaluated by means of a computer simulation technique. The computer simulation package includes coherent processing of the SAR data using a range-sequential processor, which can be set up through hardware implementations, thereby reducing the amount of telemetry involved. With such a processing approach, it is possible to monitor the earth's surface on a continuous basis, since data storage requirements can be easily met through the use of currently available technology. The Development of the simulation package is described, followed by an examination of the application of the technique to actual environments. The results indicate that in estimating soil moisture content with a four-look processor, the difference between the assumed and estimated values of soil moisture is within + or - 20% of field capacity for 62% of the pixels for agricultural terrain and for 53% of the pixels for hilly terrain. The estimation accuracy for soil moisture may be improved by reducing the effect of fading through non-coherent averaging.

Study on the combined sewage sludge pyrolysis and gasification process: mass and energy balance.

PubMed

Wang, Zhonghui; Chen, Dezhen; Song, Xueding; Zhao, Lei

2012-12-01

A combined pyrolysis and gasification process for sewage sludge was studied in this paper for the purpose of its safe disposal with energy self-balance. Three sewage sludge samples with different dry basis lower heat values (LHV(db)) were used to evaluate the constraints on this combined process. Those samples were pre-dried and then pyrolysed within the temperature range of 400-550 degrees C. Afterwards, the char obtained from pyrolysis was gasified to produce fuel gas. The experimental results showed that the char yield ranged between 37.28 and 53.75 wt% of the dry sludge and it changed with ash content, pyrolysis temperature and LHV(db) of the sewage sludge. The gas from char gasification had a LHV around 5.31-5.65 MJ/Nm3, suggesting it can be utilized to supply energy in the sewage sludge drying and pyrolysis process. It was also found that energy balance in the combined process was affected by the LHV(db) of sewage sludge, moisture content and pyrolysis temperature. Higher LHV(db), lower moisture content and higher pyrolysis temperature benefit energy self-balance. For sewage sludge with a moisture content of 80 wt%, LHV(db) of sewage sludge should be higher than 18 MJ/kg and the pyrolysis temperature should be higher than 450 degrees C to maintain energy self-sufficiency when volatile from the pyrolysis process is the only energy supplier; when the LHV(db) was in the range of 14.65-18 MJ/kg, energy self-balance could be maintained in this combined process with fuel gas from char gasification as a supplementary fuel; auxiliary fuel was always needed if the LHV(db) was lower than 14.65 MJ/kg.

Effects of spatial heterogeneity in moisture content on the horizontal spread of peat fires.

PubMed

Prat-Guitart, Nuria; Rein, Guillermo; Hadden, Rory M; Belcher, Claire M; Yearsley, Jon M

2016-12-01

The gravimetric moisture content of peat is the main factor limiting the ignition and spread propagation of smouldering fires. Our aim is to use controlled laboratory experiments to better understand how the spread of smouldering fires is influenced in natural landscape conditions where the moisture content of the top peat layer is not homogeneous. In this paper, we study for the first time the spread of peat fires across a spatial matrix of two moisture contents (dry/wet) in the laboratory. The experiments were undertaken using an open-top insulated box (22×18×6cm) filled with milled peat. The peat was ignited at one side of the box initiating smouldering and horizontal spread. Measurements of the peak temperature inside the peat, fire duration and longwave thermal radiation from the burning samples revealed important local changes of the smouldering behaviour in response to sharp gradients in moisture content. Both, peak temperatures and radiation in wetter peat (after the moisture gradient) were sensitive to the drier moisture condition (preceding the moisture gradient). Drier peat conditions before the moisture gradient led to higher temperatures and higher radiation flux from the fire during the first 6cm of horizontal spread into a wet peat patch. The total spread distance into a wet peat patch was affected by the moisture content gradient. We predicted that in most peat moisture gradients of relevance to natural ecosystems the fire self-extinguishes within the first 10cm of horizontal spread into a wet peat patch. Spread distances of more than 10cm are limited to wet peat patches below 160% moisture content (mass of water per mass of dry peat). We found that spatial gradients of moisture content have important local effects on the horizontal spread and should be considered in field and modelling studies. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Micrometeorological, evapotranspiration, and soil-moisture data at the Amargosa Desert Research site in Nye County near Beatty, Nevada, 2006-11

USGS Publications Warehouse

Arthur, Jonathan M.; Johnson, Michael J.; Mayers, C. Justin; Andraski, Brian J.

2012-11-13

This report describes micrometeorological, evapotranspiration, and soil-moisture data collected since 2006 at the Amargosa Desert Research Site adjacent to a low-level radio-active waste and hazardous chemical waste facility near Beatty, Nevada. Micrometeorological data include precipitation, solar radiation, net radiation, air temperature, relative humidity, saturated and ambient vapor pressure, wind speed and direction, barometric pressure, near-surface soil temperature, soil-heat flux, and soil-water content. Evapotranspiration (ET) data include latent-heat flux, sensible-heat flux, net radiation, soil-heat flux, soil temperature, air temperature, vapor pressure, and other principal energy-budget data. Soil-moisture data include periodic measurements of volumetric water-content at experimental sites that represent vegetated native soil, devegetated native soil, and simulated waste disposal trenches - maximum measurement depths range from 5.25 to 29.25 meters. All data are compiled in electronic spreadsheets that are included with this report.

Survey of in-situ and remote sensing methods for soil moisture determination

NASA Technical Reports Server (NTRS)

Schmugge, T. J.; Jackson, T. J.; Mckim, H. L.

1981-01-01

General methods for determining the moisture content in the surface layers of the soil based on in situ or point measurements, soil water models and remote sensing observations are surveyed. In situ methods described include gravimetric techniques, nuclear techniques based on neutron scattering or gamma-ray attenuation, electromagnetic techniques, tensiometric techniques and hygrometric techniques. Soil water models based on column mass balance treat soil moisture contents as a result of meteorological inputs (precipitation, runoff, subsurface flow) and demands (evaporation, transpiration, percolation). The remote sensing approaches are based on measurements of the diurnal range of surface temperature and the crop canopy temperature in the thermal infrared, measurements of the radar backscattering coefficient in the microwave region, and measurements of microwave emission or brightness temperature. Advantages and disadvantages of the various methods are pointed out, and it is concluded that a successful monitoring system must incorporate all of the approaches considered.

Evaluation of free water and water activity measurements as functional alternatives to total moisture content in broiler excreta and litter samples.

PubMed

van der Hoeven-Hangoor, E; Rademaker, C J; Paton, N D; Verstegen, M W A; Hendriks, W H

2014-07-01

Litter moisture contents vary greatly between and within practical poultry barns. The current experiment was designed to measure the effects of 8 different dietary characteristics on litter and excreta moisture content. Additionally, free water content and water activity of the excreta and litter were evaluated as additional quality measures. The dietary treatments consisted of nonstarch polysaccharide content (NSP; corn vs. wheat), particle size of insoluble fiber (coarse vs. finely ground oat hulls), viscosity of a nonfermentable fiber (low- and high-viscosity carboxymethyl cellulose), inclusion of a clay mineral (sepiolite), and inclusion of a laxative electrolyte (MgSO4). The 8 treatments were randomly assigned to cages within blocks, resulting in 12 replicates per treatment with 6 birds per replicate. Limited effects of the dietary treatments were noted on excreta and litter water activity, and indications were observed that this measurement is limited in high-moisture samples. Increasing dietary NSP content by feeding a corn-based diet (low NSP) compared with a wheat-based diet (high NSP) increased water intake, excreta moisture and free water, and litter moisture content. Adding insoluble fibers to the wheat-based diet reduced excreta and litter moisture content, as well as litter water activity. Fine grinding of the oat hulls diminished the effect on litter moisture and water activity. However, excreta moisture and free water content were similar when fed finely or coarsely ground oat hulls. The effects of changing viscosity and adding a clay mineral or laxative deviated from results observed in previous studies. Findings of the current experiment indicate a potential for excreta free water measurement as an additional parameter to assess excreta quality besides total moisture. The exact implication of this parameter warrants further investigation. © 2014 Poultry Science Association Inc.

Determining soil volumetric moisture content using time domain reflectometry

DOT National Transportation Integrated Search

1998-02-01

Time domain reflectometry (TDR) is a technique used to measure indirectly the in situ volumetric moisture content of soil. Current research provides a variety of prediction equations that estimate the volumetric moisture content using the dielectric ...

Pupation Behaviors and Emergence Successes of Ectropis grisescens (Lepidoptera: Geometridae) in Response to Different Substrate Types and Moisture Contents.

PubMed

Wang, Huifang; Ma, Tao; Xiao, Qiang; Cao, Panrong; Chen, Xuan; Wen, Yuzhen; Xiong, Hongpeng; Qin, Wenquan; Liang, Shiping; Jian, Shengzhe; Li, Yanjun; Sun, Zhaohui; Wen, Xiujun; Wang, Cai

2017-12-08

Ectropis grisescens Warren (Lepidoptera: Geometridae) is one of the most severe pests of tea plants in China. This species commonly pupates in soil; however, little is known about its pupation ecology. In the present study, choice and no-choice tests were conducted to investigate the pupation behaviors and emergence success of E. grisescens in response to different substrates (sand, sandy loam 1, sandy loam 2, and silt loam) and moisture contents (5, 20, 35, 50, 65, and 80%). Moisture-choice bioassays showed that significantly more E. grisescens individuals pupated in or on soil (sandy loam 1 and 2 and silt loam) that was at the intermediate moisture levels, whereas 5%- and 35%-moisture sand was significantly more preferred over 80%-moisture sand for pupating. Substrate-choice bioassays showed that sand was most preferred by E. grisescens individuals at 20%- and 80%-moisture levels, but no preference was detected among the four substrates at 50%-moisture content. No-choice tests showed that the percentage of burrowed E. grisescens individuals and pupation depth were significantly lower when soil was dry (20% moisture) or wet (80% moisture). In addition, 20%-moisture sandy loam 2 and silt loam significantly decreased the body water content of pupae and emergence success of adults compared to 50%-moisture content. However, each measurement (percentage of burrowed individuals, pupation depth, body water content, or emergence success) was similar when compared among different moisture levels of sand. Interestingly, pupae buried with 80%-moisture soil exhibited significantly lower emergence success than that were unburied. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Comparison of standard moisture loss-on-drying methods for the determination of moisture content of corn distillers dried grains with solubles.

PubMed

Ileleji, Klein E; Garcia, Arnoldo A; Kingsly, Ambrose R P; Clementson, Clairmont L

2010-01-01

This study quantified the variability among 14 standard moisture loss-on-drying (gravimetric) methods for determination of the moisture content of corn distillers dried grains with solubles (DDGS). The methods were compared with the Karl Fischer (KF) titration method to determine their percent variation from the KF method. Additionally, the thermo-balance method using a halogen moisture analyzer that is routinely used in fuel ethanol plants was included in the methods investigated. Moisture contents by the loss-on-drying methods were significantly different for DDGS samples from three fuel ethanol plants. The percent deviation of the moisture loss-on-drying methods decreased with decrease in drying temperature and, to a lesser extent, drying time. This was attributed to an overestimation of moisture content in DDGS due to the release of volatiles at high temperatures. Our findings indicate that the various methods that have been used for moisture determination by moisture loss-on-drying will not give identical results and therefore, caution should be exercised when selecting a moisture loss-on-drying method for DDGS.

The Influence of Fuel Properties on Combustion Efficiency and the Partitioning of Pyrogenic Carbon

NASA Astrophysics Data System (ADS)

Urbanski, S. P.; Baker, S. P.; Lincoln, E.; Richardson, M.

2016-12-01

The partitioning of volatized pyrogenic carbon into CO2, CO, CH4, non-methane organic carbon, and particulate organic carbon (POC) and elemental carbon (PEC) depends on the combustion characteristics of biomass fires which are influenced by the moisture content, structure and arrangement of the fuels. Flaming combustion is characterized by efficient conversion of volatized carbon into CO2. In contrast, smoldering is less efficient and produces incomplete combustion products like CH4 and carbonaceous particles. This paper presents a laboratory study that has examined the relationship between the partitioning of volatized pyrogenic carbon and specific fuel properties. The study focused on fuel beds composed of simple fuel particles — ponderosa pine needles. Ponderosa pine was selected because it contains a common wildland fuel component, conifer needles, which can be easily arranged into fuel beds of variable structure (bulk density and depth) and moisture contents that are both representative of natural conditions and are easily replicated. Modified combustion efficiency (MCE, ΔCO2/[ΔCO2+ ΔCO]) and emission factors (EF) for CO2, CO, CH4, POC, and PEC were measured over a range of needle moisture content and fuel bed bulk density and depth representative of naturally occurring fuel beds. We found that, as expected, MCE decreases as the fuel bed bulk density increases and emissions of CO, CH4, PM2.5, and POC increased. However, fuel bed depth did not appear to have an effect on how effect on MCE or emission factors. Surprisingly, a consistent relationship between the needle moisture content and emissions was not identified. At the high bulk densities, moisture content had a strong influence on MCE which explained variability in EFCH4. However, moisture content appeared to have an influence EFPOC and EFPEC that was independent of MCE. These findings may have significant implications since many models of biomass burning assume that litter fuels, such as ponderosa pine needles, burn almost exclusively via flaming combustion with a high efficiency. Our results indicate that for fuel bed properties typical of many conifer forests, pollutants generated from fires will be higher than that predicted using standard biomass burning models.

Maintaining high moisture content of macadamia nuts-in-shell during storage induces brown centres in raw kernels.

PubMed

Walton, David A; Randall, Bruce W; Le Lagadec, Marie D; Wallace, Helen M

2013-09-01

Kernel brown centres in macadamia are a defect causing internal discolouration of kernels. This study investigates the effect on the incidence of brown centres in raw kernel after maintaining high moisture content in macadamia nuts-in-shell stored at temperatures of 30°C, 35°C, 40°C and 45°C. Brown centres of raw kernel increased with nuts-in-shell storage time and temperature when high moisture content was maintained by sealing in polyethylene bags. Almost all kernels developed the defect when kept at high moisture content for 5 days at 45°C, and 44% developed brown centres after only 2 days of storage at high moisture content at 45°C. This contrasted with only 0.76% when stored for 2 days at 45°C but allowed to dry in open-mesh bags. At storage temperatures below 45°C, there were fewer brown centres, but there were still significant differences between those stored at high moisture content and those allowed to dry (P < 0.05). Maintenance of high moisture content during macadamia nuts-in-shell storage increases the incidence of brown centres in raw kernels and the defect increases with time and temperature. On-farm nuts-in-shell drying and storage practices should rapidly remove moisture to reduce losses. Ideally, nuts-in-shell should not be stored at high moisture content on-farm at temperatures over 30°C. © 2013 Society of Chemical Industry.

Effects of moisture content of food waste on residue separation, larval growth and larval survival in black soldier fly bioconversion.

PubMed

Cheng, Jack Y K; Chiu, Sam L H; Lo, Irene M C

2017-09-01

In order to foster sustainable management of food waste, innovations in food waste valorization technologies are crucial. Black soldier fly (BSF) bioconversion is an emerging technology that can turn food waste into high-protein fish feed through the use of BSF larvae. The conventional method of BSF bioconversion is to feed BSF larvae with food waste directly without any moisture adjustment. However, it was reported that difficulty has been experienced in the separation of the residue (larval excreta and undigested material) from the insect biomass due to excessive moisture. In addition to the residue separation problem, the moisture content of the food waste may also affect the growth and survival aspects of BSF larvae. This study aims to determine the most suitable moisture content of food waste that can improve residue separation as well as evaluate the effects of the moisture content of food waste on larval growth and survival. In this study, pre-consumer and post-consumer food waste with different moisture content (70%, 75% and 80%) was fed to BSF larvae in a temperature-controlled rotary drum reactor. The results show that the residue can be effectively separated from the insect biomass by sieving using a 2.36mm sieve, for both types of food waste at 70% and 75% moisture content. However, sieving of the residue was not feasible for food waste at 80% moisture content. On the other hand, reduced moisture content of food waste was found to slow down larval growth. Hence, there is a trade-off between the sieving efficiency of the residue and the larval growth rate. Furthermore, the larval survival rate was not affected by the moisture content of food waste. A high larval survival rate of at least 95% was achieved using a temperature-controlled rotary drum reactor for all treatment groups. The study provides valuable insights for the waste management industry on understanding the effects of moisture content when employing BSF bioconversion for food waste recycling. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effects of Water on Structure and Dynamics of Trehalose Glasses at Low Water Contents and its Relationship to Preservation Outcomes

NASA Astrophysics Data System (ADS)

Weng, Lindong; Ziaei, Shima; Elliott, Gloria D.

2016-07-01

Dry preservation of biologics in sugar glasses is regarded as a promising alternative to conventional cryopreservation. Evidence from various studies has suggested that there is a critical range of water content beyond which the viability of preserved biologics can be greatly compromised. In this study the viability of T-cells was determined as a function of end water content after microwave-assisted drying in trehalose solutions. Hydrogen-bonding and clustering phenomena in trehalose solutions of the same moisture content were also evaluated using molecular dynamics simulation. Post-rehydration viability decreased dramatically within the range of 0.1-1 gH2O/gdw. Molecular modeling revealed that as the water content approached 0.1 gH2O/gdw the matrix formed a large interconnected trehalose skeleton with a minimal number of bound water molecules scattered in the bulk. The diffusion coefficients of trehalose oxygen atoms most distant from the glycosidic linkage fluctuated around 7.5 × 10-14 m2/s within the range of 0.02-0.1 gH2O/gdw and increased again to ~1.13 × 10-13 m2/s at 0.01 gH2O/gdw and below due to the loss of water in the free volume between trehalose molecules. These insights can guide the optimal selection of final moisture contents to advance dry preservation methods.

Effects of Water on Structure and Dynamics of Trehalose Glasses at Low Water Contents and its Relationship to Preservation Outcomes.

PubMed

Weng, Lindong; Ziaei, Shima; Elliott, Gloria D

2016-07-08

Dry preservation of biologics in sugar glasses is regarded as a promising alternative to conventional cryopreservation. Evidence from various studies has suggested that there is a critical range of water content beyond which the viability of preserved biologics can be greatly compromised. In this study the viability of T-cells was determined as a function of end water content after microwave-assisted drying in trehalose solutions. Hydrogen-bonding and clustering phenomena in trehalose solutions of the same moisture content were also evaluated using molecular dynamics simulation. Post-rehydration viability decreased dramatically within the range of 0.1-1 gH2O/gdw. Molecular modeling revealed that as the water content approached 0.1 gH2O/gdw the matrix formed a large interconnected trehalose skeleton with a minimal number of bound water molecules scattered in the bulk. The diffusion coefficients of trehalose oxygen atoms most distant from the glycosidic linkage fluctuated around 7.5 × 10(-14) m(2)/s within the range of 0.02-0.1 gH2O/gdw and increased again to ~1.13 × 10(-13) m(2)/s at 0.01 gH2O/gdw and below due to the loss of water in the free volume between trehalose molecules. These insights can guide the optimal selection of final moisture contents to advance dry preservation methods.

Radar response to vegetation. [soil moisture mapping via microwave backscattering

NASA Technical Reports Server (NTRS)

Ulaby, F. T.

1975-01-01

Active microwave measurements of vegetation backscatter were conducted to determine the utility of radar in mapping soil moisture through vegetation and mapping crop types. Using a truck-mounted boom, spectral response data were obtained for four crop types (corn, milo, soybeans, and alfalfa) over the 4-8 GHz frequency band, at incidence angles of 0 to 70 degrees in 10-degree steps, and for all four linear polarization combinations. Based on a total of 125 data sets covering a wide range of soil moisture, content, system design criteria are proposed for each of the aforementioned objectives. Quantitative soil moisture determination was best achieved at the lower frequency end of the 4-8 GHz band using HH polarized waves in the 5- to 15-degree incidence angle range. A combination of low and high frequency measurements are suggested for classifying crop types. For crop discrimination, a dual-frequency dual-polarization (VV and cross) system operating at incidence angles above 40 degrees is suggested.

MoisturEC: an R application for geostatistical estimation of moisture content from electrical conductivity data

NASA Astrophysics Data System (ADS)

Terry, N.; Day-Lewis, F. D.; Werkema, D. D.; Lane, J. W., Jr.

2017-12-01

Soil moisture is a critical parameter for agriculture, water supply, and management of landfills. Whereas direct data (as from TDR or soil moisture probes) provide localized point scale information, it is often more desirable to produce 2D and/or 3D estimates of soil moisture from noninvasive measurements. To this end, geophysical methods for indirectly assessing soil moisture have great potential, yet are limited in terms of quantitative interpretation due to uncertainty in petrophysical transformations and inherent limitations in resolution. Simple tools to produce soil moisture estimates from geophysical data are lacking. We present a new standalone program, MoisturEC, for estimating moisture content distributions from electrical conductivity data. The program uses an indicator kriging method within a geostatistical framework to incorporate hard data (as from moisture probes) and soft data (as from electrical resistivity imaging or electromagnetic induction) to produce estimates of moisture content and uncertainty. The program features data visualization and output options as well as a module for calibrating electrical conductivity with moisture content to improve estimates. The user-friendly program is written in R - a widely used, cross-platform, open source programming language that lends itself to further development and customization. We demonstrate use of the program with a numerical experiment as well as a controlled field irrigation experiment. Results produced from the combined geostatistical framework of MoisturEC show improved estimates of moisture content compared to those generated from individual datasets. This application provides a convenient and efficient means for integrating various data types and has broad utility to soil moisture monitoring in landfills, agriculture, and other problems.

Improvements in decay resistance based on moisture exclusion

Treesearch

Roger M. Rowell; Rebecca E. Ibach

2000-01-01

Moisture content has an effect on the biological decay of wood. The literature states that serious decay occurs when the moisture content of wood is above the fiber saturation point (FSP), which is the measurement of the moisture content of wood when the cell walls are saturated and the cell cavities free from water (average 30%). We can chemically modify wood...

A comparison of two methods for estimating conifer live foliar moisture content

Treesearch

W. Matt Jolly; Ann M. Hadlow

2012-01-01

Foliar moisture content is an important factor regulating how wildland fires ignite in and spread through live fuels but moisture content determination methods are rarely standardised between studies. One such difference lies between the uses of rapid moisture analysers or drying ovens. Both of these methods are commonly used in live fuel research but they have never...

Water content and the conversion of phytochrome regulation of lettuce dormancy

NASA Technical Reports Server (NTRS)

Vertucci, C. W.; Vertucci, F. A.; Leopold, A. C.

1987-01-01

In an effort to determine which biological reactions can occur in relation to the water content of seeds, the regulation of lettuce seed dormancy by red and far red light was determined at various hydration levels. Far red light had an inhibiting effect on germination for seeds at all moisture contents from 4 to 32% water. Germination was progressively stimulated by red light as seed hydration increased from 8 to 15%, and reached a maximum at moisture contents above 18%. Red light was ineffective at moisture contents below 8%. Seeds that had been stimulated by red light and subsequently dried lost the enhanced germinability if stored at moisture contents above 8%. The contrast between the presumed photoconversion of phytochrome far red-absorbing (Pfr) to (Pr) occurring at any moisture content and the reverse reaction occurring only if the seed moisture content is greater than 8% may be explained on the basis of the existence of unstable intermediates in the Pr to Pfr conversion. Our results suggest that the initial photoreaction involved in phytochrome conversion is relatively independent of water content, while the subsequent partial reactions become increasingly facilitated as water content increases from 8 to 18%.

Factors affecting power requirements for chipping whole trees

Treesearch

Bryce J. Stokes; William F. Watson; Donald L. Sirois

1987-01-01

Large and small in-woods disk chippers were used in field tests to determine the power requirements for chipping whole trees. Hardwood and softwood species were evaluated over a range of diameter classes and moisture contents.

Study of moisture absorption by an organoplastic

NASA Astrophysics Data System (ADS)

Aniskevich, A. N.; Yanson, Yu. O.

1991-07-01

A complex experimental study of the state of sorbed moisture in a unidirectionally reinforced organoplastic was conducted. The methods of TG, DSC, DTA, and NMR showed that moisture absorption in OP is reversible up to 8%, the sorbed moisture does not crystallize in the temperature range from -70 to 0 °C, it is finely dispersely distributed and is in the strongly and weakly bound state, and there is almost no free moisture. The results of the sorption experiments conducted on OP and its structural components: microplastic and EDT-10 binder, in a wide range of temperature-humidity conditions and the data from physical studies showed that moisture absorption in the materials basically takes place by diffusion and is satisfactorily described by a phenomenological model based on the Fick equation. A method of accelerated determination of the sorption characteristics of anisotropic composite materials was developed, using the introduced concept of the fictitious diffusion coefficient and the extrapolation method of determining the limiting moisture content. The features of migration of moisture on the interface in a multiphase system were investigated, and the possibility of successive calculation estimation of the sorption characteristics of an organoplastic at different structural levels was demonstrated: components—unidirectionally reinforced composite—model laminated article. The tested phenomenological model of the sorption process and the experimentally obtained values of the characteristics of the material were the basis for a method of calculation determination of the resource of moisture-proofing properties of a model multilayer article of CM in nonstationary external conditions.

Moisture Sorption and Thermodynamic Properties of Vacuum-Dried Capsosiphon fulvescens Powder

PubMed Central

Zuo, Li; Rhim, Jong-Whan; Lee, Jun Ho

2015-01-01

The moisture sorption isotherms of vacuum-dried edible green alga (Capsosiphon fulvescens) powders were determined at 25, 35, and 45°C and water activity (aw) in the range of 0.11~0.94. An inversion effect of temperature was found at high water activity (>0.75). Various mathematical models were fitted to the experimental data, and Brunauer, Emmett, and Teller model was found to be the most suitable model describing the relationship between equilibrium moisture content and water activity (<0.45). Henderson model could also provide excellent agreement between the experimental and predicted values despite of the intersection point. Net isosteric heat of adsorption decreased from 15.77 to 9.08 kJ/mol with an increase in equilibrium moisture content from 0.055 to 0.090 kg H2O/kg solids. The isokinetic temperature (Tβ) was 434.79 K, at which all the adsorption reactions took place at the same rate. The enthalpy-entropy compensation suggested that the mechanism of the adsorption process was shown to be enthalpy-driven. PMID:26451360

Imaging wet granules with different flow patterns by electrical capacitance tomography and microwave tomography

NASA Astrophysics Data System (ADS)

Wang, H. G.; Zhang, J. L.; Ramli, M. F.; Mao, M. X.; Ye, J. M.; Yang, W. Q.; Wu, Z. P.

2016-11-01

The moisture content of granules in fluidised bed drying, granulation and coating processes can typically be between 1%~25%, resulting in the change of permittivity and conductivity during the processes. Electrical capacitance tomography (ECT) has been used for this purpose, but has a limit because too much water can cause a problem in capacitance measurement. Considering that microwave tomography (MWT) has a wide range of frequency (1~2.5 GHz) and can be used to measure materials with high permittivity and conductivity, the objective of this research is to combine ECT and MWT together to investigate the solids concentration with different moisture content and different flow patterns. The measurement results show that both ECT and MWT are functions of moisture content as well as flow patterns, and their measurements are complementary to each other. This is the first time that these two tomography modalities have been combined together and applied to image the complex solids distribution. The obtained information may be used for the process control of fluidised bed drying, granulation and coating to improve operation efficiency.

Rapid and non-destructive determination of rancidity levels in butter cookies by multi-spectral imaging.

PubMed

Xia, Qing; Liu, Changhong; Liu, Jinxia; Pan, Wenjuan; Lu, Xuzhong; Yang, Jianbo; Chen, Wei; Zheng, Lei

2016-03-30

Rancidity is an important attribute for quality assessment of butter cookies, while traditional methods for rancidity measurement are usually laborious, destructive and prone to operational error. In the present paper, the potential of applying multi-spectral imaging (MSI) technology with 19 wavelengths in the range of 405-970 nm to evaluate the rancidity in butter cookies was investigated. Moisture content, acid value and peroxide value were determined by traditional methods and then related with the spectral information by partial least squares regression (PLSR) and back-propagation artificial neural network (BP-ANN). The optimal models for predicting moisture content, acid value and peroxide value were obtained by PLSR. The correlation coefficient (r) obtained by PLSR models revealed that MSI had a perfect ability to predict moisture content (r = 0.909), acid value (r = 0.944) and peroxide value (r = 0.971). The study demonstrated that the rancidity level of butter cookies can be continuously monitored and evaluated in real-time by the multi-spectral imaging, which is of great significance for developing online food safety monitoring solutions. © 2015 Society of Chemical Industry.

[Effects of soil moisture content and light intensity on the plant growth and leaf physiological characteristics of squash].

PubMed

Du, She-ni; Bai, Gang-shuan; Liang, Yin-li

2011-04-01

A pot experiment with artificial shading was conducted to study the effects of soil moisture content and light intensity on the plant growth and leaf physiological characteristics of squash variety "Jingyingyihao". Under all test soil moisture conditions, 30% shading promoted the growth of "Jingyingyihao", with the highest yield at 70% - 80% soil relative moisture contents. 70% shading inhibited plant growth severely, only flowering and not bearing fruits, no economic yield produced. In all treatments, there was a similar water consumption trend, i. e., both the daily and the total water consumption decreased with increasing shading and decreasing soil moisture content. Among all treatments, 30% shading and 70% - 80% soil relative moisture contents had the highest water use efficiency (2.36 kg mm(-1) hm(-2)) and water output rate (1.57 kg mm(-1) hm(-2)). The net photosynthetic rate, transpiration rate, stomatal conductance, and chlorophyll content of squash leaves decreased with increasing shading, whereas the intercellular CO2 concentration was in adverse. The leaf protective enzyme activity and proline content decreased with increasing shading, and the leaf MAD content decreased in the order of 70% shading, natural radiation, and 30% shading. Under the three light intensities, the change characteristics of squash leaf photosynthesis, protective enzyme activity, and proline and MAD contents differed with the increase of soil relative moisture content.

A Probe for Measuring Moisture Content in Dead Roundwood

Treesearch

Richard W. Blank; John S. Frost; James E. Eenigenburg

1983-01-01

This paper reports field test results of a wood moisture probe''s accuracy in measuring fuel moisture content of dead roundwood. Probe measurements, corrected for temperature, correlated well with observed fuel moistures of 1-inch dead jack pine branchwood.

Effects of heat-moisture treatment reaction conditions on the physicochemical and structural properties of maize starch: moisture and length of heating.

PubMed

Sui, Zhongquan; Yao, Tianming; Zhao, Yue; Ye, Xiaoting; Kong, Xiangli; Ai, Lianzhong

2015-04-15

Changes in the properties of normal maize starch (NMS) and waxy maize starch (WMS) after heat-moisture treatment (HMT) under various reaction conditions were investigated. NMS and WMS were adjusted to moisture levels of 20%, 25% and 30% and heated at 100 °C for 2, 4, 8 and 16 h. The results showed that moisture content was the most important factor in determining pasting properties for NMS, whereas the heating length was more important for WMS. Swelling power decreased in NMS but increased in WMS, and while the solubility index decreased for both samples, the changes were largely determined by moisture content. The gelatinisation temperatures of both samples increased with increasing moisture content but remained unchanged with increasing heating length. The Fourier transform infrared (FT-IR) absorbance ratio was affected to different extents by the moisture levels but remained constant with increasing the heating length. The X-ray intensities increased but relative crystallinity decreased to a greater extent with increasing moisture content. This study showed that the levels of moisture content and length of heating had significant impacts on the structural and physicochemical properties of normal and waxy maize starches but to different extents. Copyright © 2014 Elsevier Ltd. All rights reserved.

Moisture content measurements of moss (Sphagnum spp.) using commercial sensors

USGS Publications Warehouse

Yoshikawa, K.; Overduin, P.P.; Harden, J.W.

2004-01-01

Sphagnum (spp.) is widely distributed in permafrost regions around the arctic and subarctic. The moisture content of the moss layer affects the thermal insulative capacity and preservation of permafrost. It also controls the growth and collapse history of palsas and other peat mounds, and is relevant, in general terms, to permafrost thaw (thermokarst). In this study, we test and calibrate seven different soil moisture sensors for measuring the moisture content of Sphagnum moss under laboratory conditions. The soil volume to which each probe is sensitive is one of the important parameters influencing moisture measurement, particularly in a heterogeneous medium such as moss. Each sensor has a unique response to changing moisture content levels, solution salinity, moss bulk density and to the orientation (structure) of the Sphagnum relative to the sensor. All of the probes examined here require unique polynomial calibration equations to obtain moisture content from probe output. We provide polynomial equations for dead and live Sphagnum moss (R2 > 0.99. Copyright ?? 2004 John Wiley & Sons, Ltd.

Inventory of File gdas1.t06z.sfluxgrbf00.grib2

Science.gov Websites

analysis Volumetric Soil Moisture Content [Fraction] 007 0.1-0.4 m below ground SOILW analysis Volumetric Soil Moisture Content [Fraction] 008 0-0.1 m below ground TMP analysis Temperature [K] 009 0.1-0.4 m Volumetric Soil Moisture Content [Fraction] 068 1-2 m below ground SOILW analysis Volumetric Soil Moisture

Impact of process conditions on the density and durability of wheat, oat, canola, and barley straw briquettes

DOE PAGES

Tumuluru, J. S.; Tabil, L. G.; Song, Y.; ...

2014-10-01

The present study is to understand the impact of process conditions on the quality attributes of wheat oat, barley, and canola straw briquettes. Analysis of variance indicated that briquette moisture content and initial density immediately after compaction and final density after 2 weeks of storage are strong functions of feedstock moisture content and compression pressure, whereas durability rating is influenced by die temperature and feedstock moisture content. Briquettes produced at a low feedstock moisture content of 9 % (w.b.) yielded maximum densities >700 kg/m3 for wheat, oat, canola, and barley straws. Lower feedstock moisture content of <10 % (w.b.) andmore » higher die temperatures >110 °C and compression pressure >10 MPa minimized the briquette moisture content and maximized densities and durability rating based on surface plots observations. Optimal process conditions indicated that a low feedstock moisture content of about 9 % (w.b.), high die temperature of 120–130 °C, medium-to-large hammer mill screen sizes of about 24 to 31.75 mm, and low to high compression pressures of 7.5 to 12.5 MPa minimized briquette moisture content to <8 % (w.b.) and maximized density to >700 kg/m3. Durability rating >90 % is achievable at higher die temperatures of >123 °C, lower to medium feedstock moisture contents of 9 to 12 % (w.b.), low to high compression pressures of 7.5 to 12.5 MPa, and large hammer mill screen size of 31.75 mm, except for canola where a lower compression pressure of 7.5 to 8.5 MPa and a smaller hammer mill screen size of 19 mm for oat maximized the durability rating values.« less

Monitoring hillslope moisture dynamics with surface ERT for enhancing spatial significance of hydrometric point measurements

NASA Astrophysics Data System (ADS)

Hübner, R.; Heller, K.; Günther, T.; Kleber, A.

2015-01-01

Besides floodplains, hillslopes are basic units that mainly control water movement and flow pathways within catchments of subdued mountain ranges. The structure of their shallow subsurface affects water balance, e.g. infiltration, retention, and runoff. Nevertheless, there is still a gap in the knowledge of the hydrological dynamics on hillslopes, notably due to the lack of generalization and transferability. This study presents a robust multi-method framework of electrical resistivity tomography (ERT) in addition to hydrometric point measurements, transferring hydrometric data into higher spatial scales to obtain additional patterns of distribution and dynamics of soil moisture on a hillslope. A geoelectrical monitoring in a small catchment in the eastern Ore Mountains was carried out at weekly intervals from May to December 2008 to image seasonal moisture dynamics on the hillslope scale. To link water content and electrical resistivity, the parameters of Archie's law were determined using different core samples. To optimize inversion parameters and methods, the derived spatial and temporal water content distribution was compared to tensiometer data. The results from ERT measurements show a strong correlation with the hydrometric data. The response is congruent to the soil tension data. Water content calculated from the ERT profile shows similar variations as that of water content from soil moisture sensors. Consequently, soil moisture dynamics on the hillslope scale may be determined not only by expensive invasive punctual hydrometric measurements, but also by minimally invasive time-lapse ERT, provided that pedo-/petrophysical relationships are known. Since ERT integrates larger spatial scales, a combination with hydrometric point measurements improves the understanding of the ongoing hydrological processes and better suits identification of heterogeneities.

Predicting guar seed splitting by compression between two plates using Hertz theory of contact stresses.

PubMed

Vishwakarma, R K; Shivhare, U S; Nanda, S K

2012-09-01

Hertz's theory of contact stresses was applied to predict the splitting of guar seeds during uni-axial compressive loading between 2 rigid parallel plates. The apparent modulus of elasticity of guar seeds varied between 296.18 and 116.19 MPa when force was applied normal to hilum joint (horizontal position), whereas it varied between 171.86 and 54.18 MPa when force was applied in the direction of hilum joint (vertical position) with in moisture content range of 5.16% to 15.28% (d.b.). At higher moisture contents, the seeds yielded after considerable deformation, thus showing ductile nature. Distribution of stresses below the point of contact were plotted to predict the location of critical point, which was found at 0.44 to 0.64 mm and 0.37 to 0.53 mm below the contact point in vertical and horizontal loading, respectively, depending upon moisture content. The separation of cotyledons from each other initiated before yielding of cotyledons and thus splitting of seed took place. The relationships between apparent modulus of elasticity, principal stresses with moisture content were described using second-order polynomial equations and validated experimentally. Manufacture of guar gum powder requires dehulling and splitting of guar seeds. This article describes splitting behavior of guar seeds under compressive loading. Results of this study may be used for design of dehulling and splitting systems of guar seeds. © 2012 Institute of Food Technologists®

Analysis of ingredient functionality and formulation optimization of pasta supplemented with peanut flour.

PubMed

Howard, Brandy M; Hung, Yen-Con; McWatters, Kay

2011-01-01

The working peanut pasta formulation range determined from a previous study was used to determine the effects of varying ingredient quantities and processing conditions on the pasta's quality and consumer acceptance. The variables studied were percent peanut flour substituted for durum wheat flour (30%, 40%, and 50%), amount of carrageenan (2.4%, 2.65%, and 2.9%), and drying temperature (60, 74, and 88 °C) on the final cooked pasta quality. Properties measured include color, texture, moisture content, and cooking loss. A home-use sensory test was conducted to determine consumer preferences and the optimum range for variables studied. Color lightness values ranged from 43.53 to 65.02, decreasing (becoming darker) with increased peanut flour level and increased drying temperature. Maximum cutting force for cooked pasta ranged from 1.59 N to 3.22 N, with higher values only for pasta dried at 88 °C. Moisture content ranged from 57.35% to 69.38%, and values decreased as drying temperature increased. Cooking loss ranged from 5.14% to 7.99%, increasing with higher levels of peanut flour and decreasing with higher levels of carrageenan. When prepared with 30% peanut flour and dried at 60 °C, the pasta was lighter in color, higher in moisture, and softer in texture than the varieties dried at higher temperatures and made with higher levels of peanut flour. Response surface analysis of consumer test data revealed that the optimum peanut pasta should contain between 35% and 45% peanut flour and should be dried between 60 and 71 °C; however, the pasta with 30% peanut flour was also a popular sample in the "favorite" categories. Practical Application: Most non-gluten protein fortification studies in durum wheat pasta found decreased firmness of dry and cooked pasta, increased cooking loss, increased stickiness, and darker product color when compared to traditional pasta. Partially defatted peanut flour is a versatile food ingredient and has high protein content. Since the lysine content of peanuts is higher than wheat, peanuts can be used to supplement wheat flour in food preparation. This study found by partially replacing wheat flour with peanut flour and with incorporation of hydrocolloid emulsifier, such as carrageenan or xanthan gum, dough viscosity, and pasta firmness significantly improved. Peanut pasta with high protein content and balanced amino acid profile can help support consumers with a healthy lifestyle.

Flow-specific physical properties of coconut flours

NASA Astrophysics Data System (ADS)

Manikantan, Musuvadi R.; Kingsly Ambrose, Rose P.; Alavi, Sajid

2015-10-01

Coconut milk residue and virgin coconut oil cake are important co-products of virgin coconut oil that are used in the animal feed industry. Flour from these products has a number of potential human health benefits and can be used in different food formulations. The objective of this study was to find out the flow-specific physical properties of coconut flours at three moisture levels. Coconut milk residue flour with 4.53 to 8.18% moisture content (w.b.) had bulk density and tapped density of 317.37 to 312.65 and 371.44 to 377.23 kg m-3, respectively; the corresponding values for virgin coconut oil cake flour with 3.85 to 7.98% moisture content (wet basis) were 611.22 to 608.68 and 663.55 to 672.93 kg m-3, respectively. The compressibility index and Hausner ratio increased with moisture. The angle of repose increased with moisture and ranged from 34.12 to 36.20 and 21.07 to 23.82° for coconut milk residue flour and virgin coconut oil cake flour, respectively. The coefficient of static and rolling friction increased with moisture for all test surfaces, with the plywood offering more resistance to flow than other test surfaces. The results of this study will be helpful in designing handling, flow, and processing systems for coconut milk residue and virgin coconut oil cake flours.

The Utility of Using a Near-Infrared (NIR) Camera to Measure Beach Surface Moisture

NASA Astrophysics Data System (ADS)

Nelson, S.; Schmutz, P. P.

2017-12-01

Surface moisture content is an important factor that must be considered when studying aeolian sediment transport in a beach environment. A few different instruments and procedures are available for measuring surface moisture content (i.e. moisture probes, LiDAR, and gravimetric moisture data from surface scrapings); however, these methods can be inaccurate, costly, and inapplicable, particularly in the field. Near-infrared (NIR) spectral band imagery is another technique used to obtain moisture data. NIR imagery has been predominately used through remote sensing and has yet to be used for ground-based measurements. Dry sand reflects infrared radiation given off by the sun and wet sand absorbs IR radiation. All things considered, this study assesses the utility of measuring surface moisture content of beach sand with a modified NIR camera. A traditional point and shoot digital camera was internally modified with the placement of a visible light-blocking filter. Images were taken of three different types of beach sand at controlled moisture content values, with sunlight as the source of infrared radiation. A technique was established through trial and error by comparing resultant histogram values using Adobe Photoshop with the various moisture conditions. The resultant IR absorption histogram values were calibrated to actual gravimetric moisture content from surface scrapings of the samples. Overall, the results illustrate that the NIR spectrum modified camera does not provide the ability to adequately measure beach surface moisture content. However, there were noted differences in IR absorption histogram values among the different sediment types. Sediment with darker quartz mineralogy provided larger variations in histogram values, but the technique is not sensitive enough to accurately represent low moisture percentages, which are of most importance when studying aeolian sediment transport.

Probing bias reduction to improve comparability of lint cotton water and moisture contents at moisture equilibrium

USDA-ARS?s Scientific Manuscript database

The Karl Fischer Titration (KFT) reference method is specific for water in lint cotton and was designed for samples conditioned to moisture equilibrium, thus limiting its biases. There is a standard method for moisture content – weight loss – by oven drying (OD), just not for equilibrium moisture c...

The impact of cerium oxide nanoparticles on the physiology of soybean (Glycine max (L.) Merr.) under different soil moisture conditions.

PubMed

Cao, Zhiming; Rossi, Lorenzo; Stowers, Cheyenne; Zhang, Weilan; Lombardini, Leonardo; Ma, Xingmao

2018-01-01

The ongoing global climate change raises concerns over the decreasing moisture content in agricultural soils. Our research investigated the physiological impact of two types of cerium oxide nanoparticles (CeO 2 NPs) on soybean at different moisture content levels. One CeO 2 NP was positively charged on the surface and the other negatively charged due to the polyvinylpyrrolidone (PVP) coating. The results suggest that the effect of CeO 2 NPs on plant photosynthesis and water use efficiency (WUE) was dependent upon the soil moisture content. Both types of CeO 2 NPs exhibited consistently positive impacts on plant photosynthesis at the moisture content above 70% of field capacity (θ fc ). Similar positive impact of CeO 2 NPs was not observed at 55% θ fc , suggesting that the physiological impact of CeO 2 NPs was dependent upon the soil moisture content. The results also revealed that V Cmax (maximum carboxylation rate) was affected by CeO 2 NPs, indicating that CeO 2 NPs affected the Rubisco activity which governs carbon assimilation in photosynthesis. In conclusion, CeO 2 NPs demonstrated significant impacts on the photosynthesis and WUE of soybeans and such impacts were affected by the soil moisture content. Graphical abstract Soil moisture content affects plant cerium oxide nanoparticle interactions.

Laboratory microwave measurement of the moisture content in seed cotton and ginned cotton fiber

USDA-ARS?s Scientific Manuscript database

The timely and accurate measurement of cotton fiber moisture content is important, but the measurement is often performed by laborious, time-consuming laboratory oven drying methods. Microwave technology for measuring fiber moisture content directly (not for drying only) offers potential advantages...

[Seasonal variation of proximate composition in three commercially important species in the Gulf of Nicoya, Puntarenas, Costa Rica].

PubMed

Rodríguez, Cristian Fonseca; Solera, Fabián Chavarriá; Mejía-Arana, Fernando

2013-03-01

Nutritional value of seafood for human consumption is worldwide recognized. Some information have been generated in other countries, nevertheless, there is limited information describing the chemical composition of some fishery important species caught in the Gulf of Nicoya. For this reason, we studied the levels of proximal components of the edible parts (fresh) of three commercially important species. The meat samples of snook Centropomus unionesis, the shrimp Trachypenaeus byrdi and the bivalve Polymesoda radiata, were collected from the Puntarenas local fish market during the fishing season of February 2009 to January 2010. Proximate composition analysis was determined according to AOAC methodology, and evaluated the moisture content, and protein and lipid composition of shellfish meats. The results indicated that the moisture content ranged from 74.6-80.6g/100g for snook 76.9-80.0g/100g for shrimp and 77.9-89.5g/100g for green mussel. After the moisture, the protein was the most abundant chemical fraction (6.8 to 21g/100g) showing the highest values in February for the shrimp and green mussel, and December for snook. The largest fluctuations in the lipid content were found in the snook, ranging from 0.7g/100g to 5.6g/100g; the highest values in this fraction were found in shrimp, green mussel and snook, for July, February and April samples respectively. Considering these results, we concluded that fish and shrimp species studied are a good alternative for human consumption as a source of protein and low lipid content.

A Moisture Function of Soil Heterotrophic Respiration Derived from Pore-scale Mechanisms

NASA Astrophysics Data System (ADS)

Yan, Z.; Todd-Brown, K. E.; Bond-Lamberty, B. P.; Bailey, V.; Liu, C.

2017-12-01

Soil heterotrophic respiration (HR) is an important process controlling carbon (C) flux, but its response to changes in soil water content (θ) is poorly understood. Earth system models (ESMs) use empirical moisture functions developed from specific sites to describe the HR-θ relationship in soils, introducing significant uncertainty. Generalized models derived from mechanisms that control substrate availability and microbial respiration are thus urgently needed. Here we derive, present, and test a novel moisture function fp developed from pore-scale mechanisms. This fp encapsulates primary physicochemical and biological processes controlling HR response to moisture variation in soils. We tested fp against a wide range of published data for different soil types, and found that fp reliably predicted diverse HR- relationships. The mathematical relationship between the parameters in fp and macroscopic soil properties such as porosity and organic C content was also established, enabling to estimate fp using soil properties. Compared with empirical moisture functions used in ESMs, this derived fp could reduce uncertainty in predicting the response of soil organic C stock to climate changes. In addition, this work is one of the first studies to upscale a mechanistic soil HR model based on pore-scale processes, thus linking the pore-scale mechanisms with macroscale observations.

Composition and trace element content of coal in Taiwan

USGS Publications Warehouse

Tsai, L.-Y.; Chen, C.-F.; Finkelman, R.B.

2005-01-01

To investigate the trace element contents of local coal, four coal samples were collected from operating mines in NW Taiwan. Detailed petrographic and chemical characterization analyses were then conducted. Analytical results indicate that (1) the samples were high volatile bituminous coal in rank with ash content ranging from 4.2 to 14.4% and with moisture content ranging from 2.7 to 4.6%; (2) the macerals were mostly composed of vitrinite with vitrinite reflectance less than 0.8%; (3) the sample of Wukeng mine has the highest Fe2O3 (29.5%), TI (54.8 ppm), Zn (140 ppm), and As (697 ppm) contents in ash and Hg (2.3 ppm) in the coal. If used properly, these coals should not present health hazards.

Foliar Moisture Contents of North American Conifers

Treesearch

Christopher R. Keyes

2006-01-01

Foliar moisture content (FMC) is a primary factor in the canopy ignition process as surface fire transitions to crown fire. In combination with measured stand data and assumed environmental conditions, reasonable estimates of foliar moisture content are necessary to determine and justify silvicultural targets for canopy fuels management strategies. FMC values reported...

An empirical model for the complex dielectric permittivity of soils as a function of water content

NASA Technical Reports Server (NTRS)

Wang, J. R.; Chmugge, T. J.

1978-01-01

The recent measurements on the dielectric properties of soils shows that the variation of dielectric constant with moisture content depends on soil types. The observed dielectric constant increases only slowly with moisture content up to a transition point. Beyond the transition it increases rapidly with moisture content. The moisture value of transition region was found to be higher for high clay content soils than for sandy soils. Many mixing formulas were compared with, and were found incompatible with, the measured dielectric variations of soil-water mixtures. A simple empirical model was proposed to describe the dielectric behavior of ths soil-water mixtures. The relationship between transition moisture and wilting point provides a means of estimating soil dielectric properties on the basis of texture information.

Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco.

PubMed

Makan, Abdelhadi; Assobhei, Omar; Mountadar, Mohammed

2013-01-03

This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts.For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreover, 5 experiments were carried out within initial moisture content of 55%, 65%, 70%, 75% and 85%. The initial air pressure and the initial moisture content of the mixture showed a significant effect on the aerobic composting. The experimental results demonstrated that for composting organic waste, relatively high moisture contents are better at achieving higher temperatures and retaining them for longer times.This study suggested that an initial moisture content of around 75%, under 0.6 bar, can be considered as being suitable for efficient composting of organic fraction of municipal solid waste. These last conditions, allowed maximum value of temperature and final composting product with good physicochemical properties as well as higher organic matter degradation and higher gas production. Moreover, final compost obtained showed good maturity levels and can be used for agricultural applications.

Effect of Root Moisture Content and Diameter on Root Tensile Properties.

PubMed

Yang, Yuanjun; Chen, Lihua; Li, Ning; Zhang, Qiufen

2016-01-01

The stabilization of slopes by vegetation has been a topical issue for many years. Root mechanical characteristics significantly influence soil reinforcement; therefore it is necessary to research into the indicators of root tensile properties. In this study, we explored the influence of root moisture content on tensile resistance and strength with different root diameters and for different tree species. Betula platyphylla, Quercus mongolica, Pinus tabulaeformis, and Larix gmelinii, the most popular tree species used for slope stabilization in the rocky mountainous areas of northern China, were used in this study. A tensile test was conducted after root samples were grouped by diameter and moisture content. The results showedthat:1) root moisture content had a significant influence on tensile properties; 2) slightly loss of root moisture content could enhance tensile strength, but too much loss of water resulted in weaker capacity for root elongation, and consequently reduced tensile strength; 3) root diameter had a strong positive correlation with tensile resistance; and4) the roots of Betula platyphylla had the best tensile properties when both diameter and moisture content being controlled. These findings improve our understanding of root tensile properties with root size and moisture, and could be useful for slope stabilization using vegetation.

Effect of Root Moisture Content and Diameter on Root Tensile Properties

PubMed Central

Yang, Yuanjun; Chen, Lihua; Li, Ning; Zhang, Qiufen

2016-01-01

The stabilization of slopes by vegetation has been a topical issue for many years. Root mechanical characteristics significantly influence soil reinforcement; therefore it is necessary to research into the indicators of root tensile properties. In this study, we explored the influence of root moisture content on tensile resistance and strength with different root diameters and for different tree species. Betula platyphylla, Quercus mongolica, Pinus tabulaeformis, and Larix gmelinii, the most popular tree species used for slope stabilization in the rocky mountainous areas of northern China, were used in this study. A tensile test was conducted after root samples were grouped by diameter and moisture content. The results showedthat:1) root moisture content had a significant influence on tensile properties; 2) slightly loss of root moisture content could enhance tensile strength, but too much loss of water resulted in weaker capacity for root elongation, and consequently reduced tensile strength; 3) root diameter had a strong positive correlation with tensile resistance; and4) the roots of Betula platyphylla had the best tensile properties when both diameter and moisture content being controlled. These findings improve our understanding of root tensile properties with root size and moisture, and could be useful for slope stabilization using vegetation. PMID:27003872

Capability of crop water content for revealing variability of winter wheat grain yield and soil moisture under limited irrigation.

PubMed

Zhang, Chao; Liu, Jiangui; Shang, Jiali; Cai, Huanjie

2018-08-01

Winter wheat (Triticum aestivum L.) is a major crop in the Guanzhong Plain, China. Understanding its water status is important for irrigation planning. A few crop water indicators, such as the leaf equivalent water thickness (EWT: g cm -2 ), leaf water content (LWC: %) and canopy water content (CWC: kg m -2 ), have been estimated using remote sensing techniques for a wide range of crops, yet their suitability and utility for revealing winter wheat growth and soil moisture status have not been well studied. To bridge this knowledge gap, field-scale irrigation experiments were conducted over two consecutive years (2014 and 2015) to investigate relationships of crop water content with soil moisture and grain yield, and to assess the performance of four spectral process methods for retrieving these three crop water indicators. The result revealed that the water indicators were more sensitive to soil moisture variation before the jointing stage. All three water indicators were significantly correlated with soil moisture during the reviving stage, and the correlations were stronger for leaf water indicators than that of the canopy water indicator at the jointing stage. No correlation was observed after the heading stage. All three water indicators showed good capabilities of revealing grain yield variability in jointing stage, with R 2 up to 0.89. CWC had a consistent relationship with grain yield over different growing seasons, but the performances of EWT and LWC were growing-season specific. The partial least squares regression was the most accurate method for estimating LWC (R 2 =0.72; RMSE=3.6%) and comparable capability for EWT and CWC. Finally, the work highlights the usefulness of crop water indicators to assess crop growth, productivity, and soil water status and demonstrates the potential of various spectral processing methods for retrieving crop water contents from canopy reflectance spectrums. Copyright © 2018 Elsevier B.V. All rights reserved.

Quality and shelf life evaluation of fermented sausages of buffalo meat with different levels of heart and fat.

PubMed

Ahmad, S; Srivastava, P K

2007-04-01

Investigations were carried to study the effect of heart incorporation (0%, 15% and 20%) and increasing levels of fat (20% and 25%) on physicochemical (pH, moisture content and thiobarbituric acid, TBA number) and microbiological (total plate count and yeast and mold count) quality and shelf life of semi dry sausages of buffalo meat during refrigerated storage (4°C). Different levels of fat significantly (p<0.05) increased the pH of the sausage samples. However different levels of heart incorporation did not significantly (p<0.05) affect pH, moisture content and TBA number of sausage samples. Fresh samples had pH, moisture content and TBA number in the range of 5.15-5.28, 42.4-47.4% and 0.073-0.134 respectively. Refrigerated storage significantly (p<0.05) increased TBA number of control samples while storage did not significantly (p<0.05) increase the TBA number of sodium ascorbate (SA) treated samples. Total plate counts of twelve sausage samples were f under the TFTC (too few to count) limit at the initial stage. Incorporation of different levels of heart and also increasing levels of fat did not significantly (p<0.05) increase the log TPC/g values. Yeast and molds were not detected in twelve samples of semi dry fermented sausages in their fresh condition. Storage revealed that there was a consistent decrease in pH, and moisture content. Refrigerated storage significantly (p<0.05) reduced both pH and moisture contents. TBA number and total plate counts and yeast and mold counts of controls were found to increase significantly (p<0.05) during refrigerated storage. However, in SA treated sausage, only TPC and yeast and mold count significantly (p<0.05) increased during refrigerated storage. Shelf life of the sausages was found to be 60 days under refrigerated storage (4°C).

The effect of moisture content within multilayer protective clothing on protection from radiation and steam.

PubMed

Su, Yun; Li, Jun; Song, Guowen

2018-06-01

The moisture from skin sweat and atmospheric water affects the thermal protective performance provided by multilayer protective clothing. Four levels of moisture content were selected to evaluate the impact of moisture on thermal protection under dry (thermal radiation) and wet (thermal radiation and low-pressure steam) heat exposure. Also, the role of moisture and its relationship with exposure time were analyzed based on skin heat flux and Henriques integral value. The addition of moisture to a fabric system was found to result in differences in second-degree and third-degree skin burn times. When moisture is added to a fabric system, it both acts as a thermal conductor to present a negative effect and provides a positive effect owing to thermal storage of water and evaporative heat loss. The positive or negative effects of moisture are mainly dependent on the thermal exposure time, the moisture content and the presence of hot steam.

Adsorption-desorption and degradation of insecticides clothianidin and thiamethoxam in agricultural soils.

PubMed

Li, Yang; Su, Peidong; Li, Yadong; Wen, Kejun; Bi, Guihong; Cox, Michael

2018-09-01

Studied were the adsorption-desorption and degradation of two widely used neonicotinoid insecticides clothianidin and thiamethoxam in three different agricultural soils in the state of Mississippi. The adsorptions of both the neonicotinoids fit a linear isotherm model. In different soils at different depths with different moisture contents, the adsorption distribution coefficients of clothianidin and thiamethoxam were found to be 0.62 to 1.94 and 0.59-2.03 L kg -1 , respectively. These distribution coefficients showed strong positive correlations with organic carbon content and pH of the soils. The desorptions of clothianidin and thiamethoxam also followed a linear isotherm, but were irreversible in respect to their adsorption isotherms. The desorption distribution coefficients ranged from 0.14 to 0.62 L kg -1 , increased with the decrease of organic carbon content. The degradations of clothianidin and thiamethoxam in the soils were found to be slow with half-lives ranged from 90 to 280 and 65 to 170 d for clothianidin and thiamethoxam respectively. The degradation rates increased with the increase of the organic carbon content in the soils. The moisture content in the soils had a positive effect on the degradation rates. The Groundwater Ubiquity Scores calculated from the adsorption distribution coefficient, organic content, and half-life suggest that clothianidin and thiamethoxam have moderate to high potential to leach to groundwater. Copyright © 2018 Elsevier Ltd. All rights reserved.

Leaf water content and palisade cell size.

PubMed

Canny, M J; Huang, C X

2006-01-01

The palisade cell sizes in leaves of Eucalyptus pauciflora were estimated in paradermal sections of cryo-fixed leaves imaged in the cryo-scanning electron microscope, as a quantity called the cell area fraction (CAF). Cell sizes were measured in detached leaves as a function of leaf water content, in intact leaves in the field during a day"s transpiration as a function of balance pressure of adjacent leaves, and on leaf disks equilibrated with air of relative humidities from 100 to 58%. Values of CAF ranged from 0.82 at saturation to approx. 0.3 in leaves dried to a relative water content (RWC) of 0.5, and in the field to approx. 0.58 at 15 bar (1.5 MPa) balance pressure. At a CAF of 0.58, the moisture content of the cell walls is in equilibrium with air at 90% relative humidity, which is the estimated relative humidity in the intercellular spaces. It is shown that at this moisture content, the cell walls could be exerting a pressure of approx. 50 bar on the cell contents.

Prediction of moisture variation during composting process: A comparison of mathematical models.

PubMed

Wang, Yongjiang; Ai, Ping; Cao, Hongliang; Liu, Zhigang

2015-10-01

This study was carried out to develop and compare three models for simulating the moisture content during composting. Model 1 described changes in water content using mass balance, while Model 2 introduced a liquid-gas transferred water term. Model 3 predicted changes in moisture content without complex degradation kinetics. Average deviations for Model 1-3 were 8.909, 7.422 and 5.374 kg m(-3) while standard deviations were 10.299, 8.374 and 6.095, respectively. The results showed that Model 1 is complex and involves more state variables, but can be used to reveal the effect of humidity on moisture content. Model 2 tested the hypothesis of liquid-gas transfer and was shown to be capable of predicting moisture content during composting. Model 3 could predict water content well without considering degradation kinetics. Copyright © 2015 Elsevier Ltd. All rights reserved.

Dielectric properties for prediction of moisture content in Vidalia onions

USDA-ARS?s Scientific Manuscript database

Microwave Sensing provides a means for nondestructively determining the amount of moisture in materials by sensing the dielectric properties of the material. In this study, dielectric properties of Vidalia onions were analyzed for moisture dependence at 13.36 GHz and 23°C for moisture content betwee...

Microwave moisture measurement of cotton fiber moisture content in the laboratory

USDA-ARS?s Scientific Manuscript database

The moisture content of cotton fiber is an important fiber property, but it is often measured by a laborious, time-consuming laboratory oven drying method. A program was implemented to establish the capabilities of a laboratory microwave moisture measurement instrument to perform rapid, precise and...

Effect of grain moisture content during milling on pasting profile and functional properties of amaranth fractions.

PubMed

Kumar, K Vishnuswamy Preetham; Dharmaraj, Usha; Sakhare, Suresh D; Inamdar, Aashitosh A

2016-05-01

Evaluation of functional properties of milled fractions of grain amaranth may be useful to decide the end uses of the grain. Hence, pasting profiles of amaranth fractions obtained by milling the grains at different moisture contents were studied in relation with their starch profile and also with their swelling power and solubility indices. It was observed that, for flour fraction, the viscosity parameters were lowest at 14-16 % moisture content. Swelling power and solubility indices of the samples varied as a function of grain moisture content. The middling fraction also showed similar pasting pattern with the variation of grain moisture content. The seed coat fractions showed higher gelatinization temperature compared to that of fine flour and middling fractions. However, starch content of the fine seed coat fraction was comparable with that of the flour and middling fractions. The coarse seed coat fraction showed lower viscosity parameters than the other samples. Viscosity parameters correlated well among themselves while, they did not show significant correlation with the starch content. However, the viscosity parameters showed negative correlation with the soluble amylose content. The study revealed that, the fractions obtained by milling the grains at different moisture content show differential pasting profiles and functional properties.

Electromagnetic characterization of white spruce at different moisture contents using synthetic aperture radar imaging

NASA Astrophysics Data System (ADS)

Ingemi, Christopher M.; Owusu Twumasi, Jones; Yu, Tzuyang

2018-03-01

Detection and quantification of moisture content inside wood (timber) is key to ensuring safety and reliability of timber structures. Moisture inside wood attracts insects and fosters the development of fungi to attack the timber, causing significant damages and reducing the load bearing capacity during their design life. The use of non-destructive evaluation (NDE) techniques (e.g., microwave/radar, ultrasonic, stress wave, and X-ray) for condition assessment of timber structures is a good choice. NDE techniques provide information about the level of deterioration and material properties of timber structures without obstructing their functionality. In this study, microwave/radar NDE technique was selected for the characterization of wood at different moisture contents. A 12 in-by-3.5 in-by-1.5 in. white spruce specimen (picea glauca) was imaged at different moisture contents using a 10 GHz synthetic aperture radar (SAR) sensor inside an anechoic chamber. The presence of moisture was found to increase the SAR image amplitude as expected. Additionally, integrated SAR amplitude was found beneficial in modeling the moisture content inside the wood specimen.

Impact of Different Elastomer Formulations on Moisture Permeation through Stoppers Used for Lyophilized Products Stored under Humid Conditions.

PubMed

Sasaki, Hitoshi; Kikuchi, Jun; Maeda, Terutoshi; Kuboniwa, Hitoshi

2010-01-01

The purpose of this study was to evaluate the effect of moisture permeability of different elastomer formulation stoppers, which had different moisture absorption abilities, on the increase of moisture content inside lyophilized vials during long-term storage under humid conditions. Two different elastomer formulation stoppers (high-moisture and low-moisture uptake stoppers) were compared. The increased amount of moisture content inside lyophilized vials fitted with high-moisture stoppers was higher than those fitted with low-moisture stoppers during the early stage of storage. However, this trend was reversed during the later stage of storage. Our data show that the moisture increase inside the lyophilized vials at the early stage was caused by moisture transfer from the stoppers, whereas the later moisture increase was caused by external moisture permeation through the stoppers. Results indicate that the difference in the moisture uptake profile inside the lyophilized vials at each period of storage was caused by the moisture absorption ability and moisture permeation ability of the two elastomer formulation stoppers. In terms of long-term storage stability under humid conditions, our data indicate that external moisture permeating through the stopper into the lyophilized vial during the late stage was the more important factor. In addition, the increase in moisture content at the early stage was controlled by stopper drying time. Furthermore, stopper drying time did not have an effect on moisture permeation at the late stage. Moisture permeation during the storage period appears to be dependent on the different elastomer formulations of the stoppers. The moisture permeation of different elastomer stoppers was an important factor in terms of the increased moisture content inside the lyophilized vials during the late stage of long-term storage under humid conditions. For lyophilized products stored at room temperature, the moisture permeation ability of the stopper is one of the most important factors for long-term storage stability.

Effect of heat–moisture treatment on digestibility of different cultivars of sweet potato (Ipomea batatas (L.) Lam) starch

PubMed Central

Senanayake, Suraji; Gunaratne, Anil; Ranaweera, K K D S; Bamunuarachchi, Arthur

2014-01-01

Different heat–moisture levels were applied to native starches from different cultivars of sweet potatoes available in Sri Lanka (Wariyapola red, Wariyapola white, Pallepola variety, Malaysian variety and CARI 273) to study the digestibility level. Samples were treated with 20, 25, and 30% moisture at 85°C and 120°C for 6 h and in vitro starch digestibility was tested with porcine pancreatin enzyme. A range of 19.3–23.5% digestibility was shown by the native starches with no significant difference (P < 0.05). Significant changes were observed in the digestibility level of the hydrothermally modified starches and the moisture content showed a positive impact on the digestibility. Heat–moisture treatment at 85°C brought an overall increase in digestibility and temperature beyond 85°C had a negative impact. No significant difference (P < 0.05) in the digestibility was observed with 20% and 25% moisture at 85°C and increased level were seen at 85°C and 30% moisture. PMID:25473497

Inversion algorithms for the microwave remote sensing of soil moisture. Experiments with swept frequency microwaves

NASA Technical Reports Server (NTRS)

Hancock, G. D.; Waite, W. P.

1984-01-01

Two experiments were performed employing swept frequency microwaves for the purpose of investigating the reflectivity from soil volumes containing both discontinuous and continuous changes in subsurface soil moisture content. Discontinuous moisture profiles were artificially created in the laboratory while continuous moisture profiles were induced into the soil of test plots by the environment of an agricultural field. The reflectivity for both the laboratory and field experiments was measured using bi-static reflectometers operated over the frequency ranges of 1.0 to 2.0 GHz and 4.0 to 8.0 GHz. Reflectivity models that considered the discontinuous and continuous moisture profiles within the soil volume were developed and compared with the results of the experiments. This comparison shows good agreement between the smooth surface models and the measurements. In particular the comparison of the smooth surface multi-layer model for continuous moisture profiles and the yield experiment measurements points out the sensitivity of the specular component of the scattered electromagnetic energy to the movement of moisture in the soil.

In-line multipoint near-infrared spectroscopy for moisture content quantification during freeze-drying.

PubMed

Kauppinen, Ari; Toiviainen, Maunu; Korhonen, Ossi; Aaltonen, Jaakko; Järvinen, Kristiina; Paaso, Janne; Juuti, Mikko; Ketolainen, Jarkko

2013-02-19

During the past decade, near-infrared (NIR) spectroscopy has been applied for in-line moisture content quantification during a freeze-drying process. However, NIR has been used as a single-vial technique and thus is not representative of the entire batch. This has been considered as one of the main barriers for NIR spectroscopy becoming widely used in process analytical technology (PAT) for freeze-drying. Clearly it would be essential to monitor samples that reliably represent the whole batch. The present study evaluated multipoint NIR spectroscopy for in-line moisture content quantification during a freeze-drying process. Aqueous sucrose solutions were used as model formulations. NIR data was calibrated to predict the moisture content using partial least-squares (PLS) regression with Karl Fischer titration being used as a reference method. PLS calibrations resulted in root-mean-square error of prediction (RMSEP) values lower than 0.13%. Three noncontact, diffuse reflectance NIR probe heads were positioned on the freeze-dryer shelf to measure the moisture content in a noninvasive manner, through the side of the glass vials. The results showed that the detection of unequal sublimation rates within a freeze-dryer shelf was possible with the multipoint NIR system in use. Furthermore, in-line moisture content quantification was reliable especially toward the end of the process. These findings indicate that the use of multipoint NIR spectroscopy can achieve representative quantification of moisture content and hence a drying end point determination to a desired residual moisture level.

40 CFR 63.2266 - Initial compliance demonstration for a veneer redryer.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... If you operate a veneer redryer, you must record the inlet moisture content of the veneer processed... average inlet veneer moisture content with your Notification of Compliance Status to show that your veneer redryer processes veneer with an inlet moisture content of less than or equal to 25 percent (by weight...

40 CFR 63.2266 - Initial compliance demonstration for a veneer redryer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... operate a veneer redryer, you must record the inlet moisture content of the veneer processed in the... inlet veneer moisture content with your Notification of Compliance Status to show that your veneer redryer processes veneer with an inlet moisture content of less than or equal to 25 percent (by weight...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2013 CFR

2013-07-01

... inlet moisture content of less than or equal to 30 percent (by weight, dry basis) and operates with a... dry rotary dryer. You must record the inlet furnish moisture content (dry basis) and inlet dryer... days. You must submit the highest recorded 24-hour average inlet furnish moisture content and the...

40 CFR 63.2266 - Initial compliance demonstration for a veneer redryer.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operate a veneer redryer, you must record the inlet moisture content of the veneer processed in the... inlet veneer moisture content with your Notification of Compliance Status to show that your veneer redryer processes veneer with an inlet moisture content of less than or equal to 25 percent (by weight...

40 CFR 63.2266 - Initial compliance demonstration for a veneer redryer.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... If you operate a veneer redryer, you must record the inlet moisture content of the veneer processed... average inlet veneer moisture content with your Notification of Compliance Status to show that your veneer redryer processes veneer with an inlet moisture content of less than or equal to 25 percent (by weight...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2012 CFR

2012-07-01

... inlet moisture content of less than or equal to 30 percent (by weight, dry basis) and operates with a... dry rotary dryer. You must record the inlet furnish moisture content (dry basis) and inlet dryer... days. You must submit the highest recorded 24-hour average inlet furnish moisture content and the...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2014 CFR

2014-07-01

... inlet moisture content of less than or equal to 30 percent (by weight, dry basis) and operates with a... dry rotary dryer. You must record the inlet furnish moisture content (dry basis) and inlet dryer... days. You must submit the highest recorded 24-hour average inlet furnish moisture content and the...

40 CFR 63.2266 - Initial compliance demonstration for a veneer redryer.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... If you operate a veneer redryer, you must record the inlet moisture content of the veneer processed... average inlet veneer moisture content with your Notification of Compliance Status to show that your veneer redryer processes veneer with an inlet moisture content of less than or equal to 25 percent (by weight...

The role of moisture content in above-ground leaching

Treesearch

Stan Lebow; Patricia Lebow

2007-01-01

This paper reviews previous reports on the moisture content of wood exposed above ground and compares those values to moisture contents obtained using simulated rainfall and immersion methods. Laboratory leaching trials with CCA-treated specimens were also conducted and the results compared to published values for leaching of CCA-treated specimens exposed above ground...

A Compound Sensor for Simultaneous Measurement of Packing Density and Moisture Content of Silage.

PubMed

Meng, Delun; Meng, Fanjia; Sun, Wei; Deng, Shuang

2017-12-28

Packing density and moisture content are important factors in investigating the ensiling quality. Low packing density is a major cause of loss of sugar content. The moisture content also plays a determinant role in biomass degradation. To comprehensively evaluate the ensiling quality, this study focused on developing a compound sensor. In it, moisture electrodes and strain gauges were embedded into an ASABE Standard small cone for the simultaneous measurements of the penetration resistance (PR) and moisture content (MC) of silage. In order to evaluate the performance of the designed sensor and the theoretical analysis being used, relevant calibration and validation tests were conducted. The determination coefficients are 0.996 and 0.992 for PR calibration and 0.934 for MC calibration. The validation indicated that this measurement technique could determine the packing density and moisture content of the silage simultaneously and eliminate the influence of the friction between the penetration shaft and silage. In this study, we not only design a compound sensor but also provide an alternative way to investigate the ensiling quality which would be useful for further silage research.

Performance of EVA-Based Membranes for SCL in Hard Rock

NASA Astrophysics Data System (ADS)

Holter, Karl Gunnar

2016-04-01

The bonded property of multi-layered sprayed concrete tunnel linings (SCL) waterproofed with sprayed membranes means that the constituent materials will be exposed to the groundwater without any draining or mechanically separating measures. Moisture properties of the sprayed concrete and membrane materials are therefore important in order to establish the system properties of such linings. Ethyl-vinyl-acetate based sprayed membranes exhibit high water absorption potential under direct exposure to water, but are found to be significantly less hygroscopic and exhibit lower sorptivity (water absorption rate) than sprayed concrete. This material behavior explains the relatively dry in situ condition of the membrane that was observed. Measured in situ moisture content levels of the membrane material in tunnel linings have been found to vary within the range of 30-40 % of the maximum water absorption potential, and show a decreasing trend over the first 4 years after construction has been completed. A model for the mechanical loading, moisture condition and thermal exposure of the membrane and the resulting realistic parameters to be tested is presented. Laboratory testing methods for the membrane materials are evaluated considering possible loads, moisture and freezing exposure. Material testing of membrane materials was conducted with preconditioning to realistic moisture contents and under different temperature conditions including relevant freezing temperatures for tunnel linings. The main effects of the in situ moisture condition of the tested membrane materials are favorable tensile strengths in the range of 1.1-1.5 MPa and low risk of freeze-thaw damage. The crack bridging capacity of the tested membranes is found to be sensitive to temperature. With membrane thicknesses in the range of 3-4 mm, crack bridging capacity up to 4-6 mm opening of the crack width at 23 °C and approximately 1 mm opening at -3 °C was measured for the tested membranes. No significant reduction of the tensile bond strength could be demonstrated after 35 freeze-thaw cycles with -3 °C minimum temperature at the membrane location in the lining. Further work is required to verify the performance of the SCL system under exposure to high hydrostatic pressures and the effects of long term mechanical exposure.

Spatiotemporal monitoring of soil water content profiles in an irrigated field using probabilistic inversion of time-lapse EMI data

NASA Astrophysics Data System (ADS)

Moghadas, Davood; Jadoon, Khan Zaib; McCabe, Matthew F.

2017-12-01

Monitoring spatiotemporal variations of soil water content (θ) is important across a range of research fields, including agricultural engineering, hydrology, meteorology and climatology. Low frequency electromagnetic induction (EMI) systems have proven to be useful tools in mapping soil apparent electrical conductivity (σa) and soil moisture. However, obtaining depth profile water content is an area that has not been fully explored using EMI. To examine this, we performed time-lapse EMI measurements using a CMD mini-Explorer sensor along a 10 m transect of a maize field over a 6 day period. Reference data were measured at the end of the profile via an excavated pit using 5TE capacitance sensors. In order to derive a time-lapse, depth-specific subsurface image of electrical conductivity (σ), we applied a probabilistic sampling approach, DREAM(ZS) , on the measured EMI data. The inversely estimated σ values were subsequently converted to θ using the Rhoades et al. (1976) petrophysical relationship. The uncertainties in measured σa, as well as inaccuracies in the inverted data, introduced some discrepancies between estimated σ and reference values in time and space. Moreover, the disparity between the measurement footprints of the 5TE and CMD Mini-Explorer sensors also led to differences. The obtained θ permitted an accurate monitoring of the spatiotemporal distribution and variation of soil water content due to root water uptake and evaporation. The proposed EMI measurement and modeling technique also allowed for detecting temporal root zone soil moisture variations. The time-lapse θ monitoring approach developed using DREAM(ZS) thus appears to be a useful technique to understand spatiotemporal patterns of soil water content and provide insights into linked soil moisture vegetation processes and the dynamics of soil moisture/infiltration processes.

Evaluation of soil pH and moisture content on in-situ ozonation of pyrene in soils.

PubMed

Luster-Teasley, S; Ubaka-Blackmoore, N; Masten, S J

2009-08-15

In this study, pyrene spiked soil (300 ppm) was ozonated at pH levels of 2, 6, and 8 and three moisture contents. It was found that soil pH and moisture content impacted the effectiveness of PAH oxidation in unsaturated soils. In air-dried soils, as pH increased, removal increased, such that pyrene removal efficiencies at pH 6 and pH 8 reached 95-97% at a dose of 2.22 mg O(3)/mg pyrene. Ozonation at 16.2+/-0.45 mg O(3)/ppm pyrene in soil resulted in 81-98% removal of pyrene at all pH levels tested. Saturated soils were tested at dry, 5% or 10% moisture conditions. The removal of pyrene was slower in moisturized soils, with the efficiency decreasing as the moisture content increased. Increasing the pH of the soil having a moisture content of 5% resulted in improved pyrene removals. On the contrary, in the soil having a moisture content of 10%, as the pH increased, pyrene removal decreased. Contaminated PAH soils were stored for 6 months to compare the efficiency of PAH removal in freshly contaminated soil and aged soils. PAH adsorption to soil was found to increase with longer exposure times; thus requiring much higher doses of ozone to effectively oxidize pyrene.

Diffusion of water in the endosperm tissue of wheat grains as studied by pulsed field gradient nuclear magnetic resonance.

PubMed

Callaghan, P T; Jolley, K W; Lelievre, J

1979-10-01

Pulsed field gradient nuclear magnetic resonance has been used to measure water self-diffusion coefficients in the endosperm tissue of wheat grains as a function of the tissue water content. A model that confines the water molecules to a randomly oriented array of capillaries with both transverse dimension less than 100 nm has been used to fit the data and give a unique diffusion coefficient at each water content. The diffusion rates vary from 1.8 x 10(-10) m2s-1 at the lowest to 1.2 x 10(-9) m2s-1 at the highest moisture content. This variation can be explained in terms of an increase in water film thickness from approximately 0.5 to approximately 2.5 nm over the moisture range investigated (200-360 mg g-1).

Historical development of grain moisture measurement and other food quality sensing through electrical properties.

USDA-ARS?s Scientific Manuscript database

A review of the use of electrical properties of agricultural products for sensing moisture content and other qualities shows that their use for rapid measurements of the moisture content in grain and seed has been the most successful application. Discovery of useful correlations between the moistur...

Measuring moisture content in living chaparral: a field user's manual

Treesearch

Clive M. Countryman; William A. Dean

1979-01-01

This manual standardizes procedures for determining the moisture content of living chaparral for use in a proposed statewide system of monitoring living fuel moisture. The manual includes a comprehensive examination of fuel moisture variations in California chaparral, and describes techniques for sampling these variations. Equipment needed to sample and determine...

Improvement in antioxidant functionality and shelf life of yukwa (fried rice snack) by turmeric (Curcuma longa L.) powder addition.

PubMed

Lim, Seung-Taik; Han, Jung-Ah

2016-05-15

The physico-chemical, oxidative and sensory characteristics of fried rice snack, yukwa with different amounts of turmeric powder (Curcuma longa) were investigated. The moisture content of the pallet ranged from 16.47% to 19.84%. After frying the pallet, a slight decrease in the degree of expansion was obtained with increasing turmeric powder content. The textural properties of yukwa were not changed until the turmeric powder content reached 5%; however, over 8% addition induced a decrease in the hardness and an increase in the crispiness. Oxidative deterioration was effectively inhibited by turmeric powder addition, and more turmeric powder in yukwa led to higher free radical scavenging activity. Based on the sensory characteristics, a 5% addition of turmeric powder was the most acceptable for the yukwa product. In the correlation results among variables, the moisture content of the pallet proved to be the most important factor for yukwa quality. Copyright © 2015 Elsevier Ltd. All rights reserved.

Surveillance of moist snuff: total nicotine, moisture, pH, un-ionized nicotine, and tobacco-specific nitrosamines.

PubMed

Richter, Patricia; Hodge, Knachelle; Stanfill, Stephen; Zhang, Liqin; Watson, Clifford

2008-11-01

In 2005, approximately 2.3% of U.S. adults used smokeless tobacco. Moist snuff leads all types of smokeless tobacco in revenues and marketing expenditures. The U.S. Surgeon General has concluded that smokeless tobacco use can lead to nicotine addiction. The National Toxicology Program of the National Institutes of Health has classified smokeless tobacco as a human carcinogen. Tobacco-specific nitrosamines (TSNAs) are potent carcinogens in smokeless tobacco products, and the pH of the product influences the content of un-ionized nicotine which is the form of nicotine most rapidly absorbed in the mouth. The Centers for Disease Control and Prevention analyzed 40 top-selling brands of moist snuff to measure nicotine, moisture, pH, un-ionized nicotine, and TSNAs, including 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanol (NNAL). The study findings indicate that moist snuff brands varied widely in content of rapidly absorbed, addictive un-ionized nicotine (500-fold range) and of carcinogenic TSNAs (18-fold range). Product characteristics such as packaging and moisture content appeared to be correlated with concentrations of un-ionized nicotine, and flavor characteristics of low-priced brands may correlate with TSNA concentrations. These findings warrant further study in light of (a) the marketing of smokeless tobacco for use in places where smoking is prohibited, (b) the promotion of smokeless tobacco as a harm-reduction product, and (c) the ever-expanding number of highly flavored smokeless varieties brought to the market.

Microwave Moisture Sensing of Seedcotton: Part 1: Seedcotton Microwave Material Properties.

PubMed

Pelletier, Mathew G; Wanjura, John D; Holt, Greg A

2016-11-02

Moisture content at harvest is a key parameter that impacts quality and how well the cotton crop can be stored without degrading before processing. It is also a key parameter of interest for harvest time field trials as it can directly influence the quality of the harvested crop as well as skew the results of in-field yield and quality assessments. Microwave sensing of moisture has several unique advantages over lower frequency sensing approaches. The first is that microwaves are insensitive to variations in conductivity, due to presence of salts or minerals. The second advantage is that microwaves can peer deep inside large bulk packaging to assess the internal moisture content without performing a destructive tear down of the package. To help facilitate the development of a microwave moisture sensor for seedcotton; research was performed to determine the basic microwave properties of seedcotton. The research was performed on 110 kg micro-modules, which are of direct interest to research teams for use in ongoing field-based research projects. It should also prove useful for the enhancement of existing and future yield monitor designs. Experimental data was gathered on the basic relations between microwave material properties and seedcotton over the range from 1.0 GHz to 2.5 GHz and is reported on herein. This research is part one of a two-part series that reports on the fundamental microwave properties of seedcotton as moisture and density vary naturally during the course of typical harvesting operations; part two will utilize this data to formulate a prediction algorithm to form the basis for a prototype microwave moisture sensor.

Strengths and weaknesses of temporal stability analysis for monitoring and estimating grid-mean soil moisture in a high-intensity irrigated agricultural landscape

NASA Astrophysics Data System (ADS)

Ran, Youhua; Li, Xin; Jin, Rui; Kang, Jian; Cosh, Michael H.

2017-01-01

Monitoring and estimating grid-mean soil moisture is very important for assessing many hydrological, biological, and biogeochemical processes and for validating remotely sensed surface soil moisture products. Temporal stability analysis (TSA) is a valuable tool for identifying a small number of representative sampling points to estimate the grid-mean soil moisture content. This analysis was evaluated and improved using high-quality surface soil moisture data that were acquired by a wireless sensor network in a high-intensity irrigated agricultural landscape in an arid region of northwestern China. The performance of the TSA was limited in areas where the representative error was dominated by random events, such as irrigation events. This shortcoming can be effectively mitigated by using a stratified TSA (STSA) method, proposed in this paper. In addition, the following methods were proposed for rapidly and efficiently identifying representative sampling points when using TSA. (1) Instantaneous measurements can be used to identify representative sampling points to some extent; however, the error resulting from this method is significant when validating remotely sensed soil moisture products. Thus, additional representative sampling points should be considered to reduce this error. (2) The calibration period can be determined from the time span of the full range of the grid-mean soil moisture content during the monitoring period. (3) The representative error is sensitive to the number of calibration sampling points, especially when only a few representative sampling points are used. Multiple sampling points are recommended to reduce data loss and improve the likelihood of representativeness at two scales.

Microwave Moisture Sensing of Seedcotton: Part 1: Seedcotton Microwave Material Properties

PubMed Central

Pelletier, Mathew G.; Wanjura, John D.; Holt, Greg A.

2016-01-01

Moisture content at harvest is a key parameter that impacts quality and how well the cotton crop can be stored without degrading before processing. It is also a key parameter of interest for harvest time field trials as it can directly influence the quality of the harvested crop as well as skew the results of in-field yield and quality assessments. Microwave sensing of moisture has several unique advantages over lower frequency sensing approaches. The first is that microwaves are insensitive to variations in conductivity, due to presence of salts or minerals. The second advantage is that microwaves can peer deep inside large bulk packaging to assess the internal moisture content without performing a destructive tear down of the package. To help facilitate the development of a microwave moisture sensor for seedcotton; research was performed to determine the basic microwave properties of seedcotton. The research was performed on 110 kg micro-modules, which are of direct interest to research teams for use in ongoing field-based research projects. It should also prove useful for the enhancement of existing and future yield monitor designs. Experimental data was gathered on the basic relations between microwave material properties and seedcotton over the range from 1.0 GHz to 2.5 GHz and is reported on herein. This research is part one of a two-part series that reports on the fundamental microwave properties of seedcotton as moisture and density vary naturally during the course of typical harvesting operations; part two will utilize this data to formulate a prediction algorithm to form the basis for a prototype microwave moisture sensor. PMID:27827857

The effects of vegetation cover on the radar and radiometric sensitivity to soil moisture

NASA Technical Reports Server (NTRS)

Ulaby, F. T.; Dobson, M. C.; Brunfeldt, D. R.; Razani, M.

1982-01-01

The measured effects of vegetation canopies on radar and radiometric sensitivity to soil moisture are compared to emission and scattering models. The models are found to predict accurately the measured emission and backscattering for various crop canopies at frequencies between 1.4 and 5.0 GHz, especially at theta equal to or less than 30 deg. Vegetation loss factors, L(theta), increase with frequency and are found to be dependent upon canopy type and water content. In addition, the radiometric power absorption coefficient of a mature corn canopy is 1.75 times that calculated for the radar. Comparison of an L-band radiometer with a C-band radar shows the two systems to be complementary in terms of accurate soil moisture sensing over the extreme range of naturally occurring soil moisture conditions.

Studies of Water Absorption Behavior of Plant Fibers at Different Temperatures

NASA Astrophysics Data System (ADS)

Saikia, Dip

2010-05-01

Moisture absorption of natural fiber plastic composites is one major concern in their outdoor applications. The absorbed moisture has many detrimental effects on the mechanical performance of these composites. A knowledge of the moisture diffusivity, permeability, and solubility is very much essential for the application of natural fibers as an excellent reinforcement in polymers. An effort has been made to study the water absorption behavior of some natural fibers such as bowstring hemp, okra, and betel nut at different temperatures to improve the long-term performance of composites reinforced with these fibers. The gain in moisture content in the fibers due to water absorption was measured as a function of exposure time at temperatures ranging from 300 K to 340 K. The thermodynamic parameters of the sorption process, such as diffusion coefficients and corresponding activation energies, were estimated.

Effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco

PubMed Central

2013-01-01

This study aimed to evaluate the effect of initial moisture content on the in-vessel composting under air pressure of organic fraction of municipal solid waste in Morocco in terms of internal temperature, produced gases quantity, organic matter conversion rate, and the quality of the final composts. For this purpose, in-vessel bioreactor was designed and used to evaluate both appropriate initial air pressure and appropriate initial moisture content for the composting process. Moreover, 5 experiments were carried out within initial moisture content of 55%, 65%, 70%, 75% and 85%. The initial air pressure and the initial moisture content of the mixture showed a significant effect on the aerobic composting. The experimental results demonstrated that for composting organic waste, relatively high moisture contents are better at achieving higher temperatures and retaining them for longer times. This study suggested that an initial moisture content of around 75%, under 0.6 bar, can be considered as being suitable for efficient composting of organic fraction of municipal solid waste. These last conditions, allowed maximum value of temperature and final composting product with good physicochemical properties as well as higher organic matter degradation and higher gas production. Moreover, final compost obtained showed good maturity levels and can be used for agricultural applications. PMID:23369502

Effects of soil moisture on dust emission from 2011 to 2015 observed over the Horqin Sandy Land area, China

NASA Astrophysics Data System (ADS)

Ju, Tingting; Li, Xiaolan; Zhang, Hongsheng; Cai, Xuhui; Song, Yu

2018-06-01

Using the observational data of dust concentrations and meteorological parameters from 2011 to 2015, the effects of soil moisture and air humidity on dust emission were studied at long (monthly) and short (several days or hours) time scales over the Horqin Sandy Land area, Inner Mongolia of China. The results show that the monthly mean dust concentrations and dust fluxes within the near-surface layer had no obvious relationship with the monthly mean soil moisture content but had a slightly negative correlation with monthly mean air relative humidity from 2011 to 2015. The daily mean soil moisture exhibited a significantly negative correlation with the daily mean dust concentrations and dust fluxes, as soil moisture changed obviously. However, such negative correlation between soil moisture and dust emission disappeared on dust blowing days. Additionally, the effect of soil moisture on an important parameter for dust emission, the threshold friction velocity (u∗t), was investigated during several saltation-bombardment and/or aggregation-disintegration dust emission (SADE) events. Under dry soil conditions, the values of u∗t were not influenced by soil moisture content; however, when the soil moisture content was high, the values of u∗t increased with increasing soil moisture content.

Sorption isotherm characteristics of aonla flakes.

PubMed

Alam, Md Shafiq; Singh, Amarjit

2011-06-01

The equilibrium moisture content was determined for un-osmosed and osmosed (salt osmosed and sugar osmosed) aonla flakes using the static method at temperatures of 25, 40,50, 60 and 70 °C over a range of relative humidities from 20 to 90%. The sorption capacity of aonla decreased with an increase in temperature at constant water activity. The sorption isotherms exhibited hysteresis, in which the equilibrium moisture content was higher at a particular equilibrium relative humidity for desorption curve than for adsorption. The hysteresis effect was more pertinent for un-osmosed and salt osmosed samples in comparison to sugar osmosed samples. Five models namely the modified Chung Pfost, modified Halsey, modified Henderson, modified Exponential and Guggenheim-Anderson-de Boer (GAB) were evaluated to determine the best fit for the experimental data. For both adsorption and desorption process of aonla fruit, the equilibrium moisture content of un-osmosed and osmosed aonla samples can be predicted well by GAB model as well as modified Exponential model. Moreover, the modified Exponential model was found to be the best for describing the sorption behaviour of un-osmosed and salt osmosed samples while, GAB model for sugar osmosed aonla samples.

Influence of wood-derived biochar on the compactibility and strength of silt loam soil

NASA Astrophysics Data System (ADS)

Ahmed, Ahmed; Gariepy, Yvan; Raghavan, Vijaya

2017-04-01

Biochar is proven to enhance soil fertility and increase crop productivity. Given that the influence of biochar on soil compaction remains unclear, selected physico-mechanical properties of soil amended with wood-derived biochar were assessed. For unamended silt loam, the bulk density, maximum bulk density, optimum moisture content, plastic limit, liquid limit, and plasticity index were 1.05 Mg m-3, 1.69 Mg m-3, 16.55, 17.1, 29.3, and 12.2%, respectively. The penetration resistance and shear strength of the unamended silt loam compacted in the standard compaction Proctor mold and at its optimum moisture content were 1800 kPa and 850 kPa, respectively. Results from amending the silt loam with 10% particle size ranges (0.5-212 μm) led to relative decreases of 18.1, 17.75, 66.66, and 97.4% in bulk density, maximum bulk density, penetration resistance, and shear strength, respectively; a 26.8% relative increase in optimum moisture content; along with absolute increases in plastic limit, liquid limit, and plasticity index of 5.3, 13.7, and 8.4%, respectively. While the biochar-amended silt loam soil was more susceptible to compaction, however, soil mechanical impedance enhanced.

Determination of Moisture Content in Coke with 239Pu-Be Neutron Source and BGO Scintillation Gamma Detector

NASA Astrophysics Data System (ADS)

Grozdanov, D. N.; Aliyev, F. A.; Hramco, C.; Kopach, Yu. N.; Bystritsky, V. M.; Skoy, V. R.; Gundorin, N. A.; Ruskov, I. N.

2018-03-01

A series of experiments has been conducted at the Frank Laboratory of Neutron Physics (FLNP) of the Joint Institute for Nuclear Research (JINR) in order to study the possibility of determining the moisture content of coke using a standard neutron source. The proposed method is based on a measurement of the spectrum of prompt γ rays emitted when samples are irradiated by fast and/or thermal neutrons. The moisture content is determined from the area of the peaks of characteristic γ rays produced in the radiative capture of thermal neutrons by the proton ( E γ = 2.223 MeV) and inelastic scattering of fast neutrons by 16O (Eγ = 6.109 MeV). The 239Pu-Be neutron source (< E n > 4.5 MeV) with an intensity of 5 × 106 n/s was used to irradiate the samples under study. A scintillation detector based on a BGO crystal was used to register the characteristic γ radiation from the inelastic fast neutron scattering and slow (thermal) neutron capture. This paper presents the results of humidity measurement in the range of 2-50% [1, 2].

Model-based surface soil moisture (SSM) retrieval algorithm using multi-temporal RISAT-1 C-band SAR data

NASA Astrophysics Data System (ADS)

Pandey, Dharmendra K.; Maity, Saroj; Bhattacharya, Bimal; Misra, Arundhati

2016-05-01

Accurate measurement of surface soil moisture of bare and vegetation covered soil over agricultural field and monitoring the changes in surface soil moisture is vital for estimation for managing and mitigating risk to agricultural crop, which requires information and knowledge to assess risk potential and implement risk reduction strategies and deliver essential responses. The empirical and semi-empirical model-based soil moisture inversion approach developed in the past are either sensor or region specific, vegetation type specific or have limited validity range, and have limited scope to explain physical scattering processes. Hence, there is need for more robust, physical polarimetric radar backscatter model-based retrieval methods, which are sensor and location independent and have wide range of validity over soil properties. In the present study, Integral Equation Model (IEM) and Vector Radiative Transfer (VRT) model were used to simulate averaged backscatter coefficients in various soil moisture (dry, moist and wet soil), soil roughness (smooth to very rough) and crop conditions (low to high vegetation water contents) over selected regions of Gujarat state of India and the results were compared with multi-temporal Radar Imaging Satellite-1 (RISAT-1) C-band Synthetic Aperture Radar (SAR) data in σ°HH and σ°HV polarizations, in sync with on field measured soil and crop conditions. High correlations were observed between RISAT-1 HH and HV with model simulated σ°HH & σ°HV based on field measured soil with the coefficient of determination R2 varying from 0.84 to 0.77 and RMSE varying from 0.94 dB to 2.1 dB for bare soil. Whereas in case of winter wheat crop, coefficient of determination R2 varying from 0.84 to 0.79 and RMSE varying from 0.87 dB to 1.34 dB, corresponding to with vegetation water content values up to 3.4 kg/m2. Artificial Neural Network (ANN) methods were adopted for model-based soil moisture inversion. The training datasets for the NNs were obtained from theoretical forward-scattering models with controlled parameters, thus allowing the control of wide range of soil and crop parameters with which the network was trained. A preliminary performance analysis showed good results with estimation of soil moisture with RMSE better than 6%.

Equilibrated moisture content of several carbon phenolics and their relationship to resin, fiber, and interface properties

NASA Technical Reports Server (NTRS)

Stokes, E. H.

1991-01-01

This study focuses on the relationship between relative humidity and the equilibrated moisture content of several variants of two distinctly different carbon phenolic composites. One of the materials gives a typical exponential relationship between RH and equilibrated moisture content while the second gives an inverse sigmoidal relationship with the largest increase in moisture between 45-60 percent relative humidity. The possible relationship between the shape of the curves and the nature of the material constituents is discussed.

Brick Paving Systems in Expeditionary Environments: Field Testing

DTIC Science & Technology

2012-07-01

specific gravity of 2.7, optimum moisture content of 2.6 percent, and a maximum dry density of 114.2 pcf. Figure 5 shows the Proctor curve developed by...4  Figure 3. Dry density versus moisture content for CH material...6  Figure 5. Dry density versus moisture content for blended GM base course. ..................................... 7  Figure 6

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with... inlet furnish moisture content at less than or equal to 30 percent (by weight, dry basis) AND... records of the inlet temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood...

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with... inlet furnish moisture content at less than or equal to 30 percent (by weight, dry basis) AND... records of the inlet temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood...

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with... inlet furnish moisture content at less than or equal to 30 percent (by weight, dry basis) AND... records of the inlet temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood...

Chemical modification : a non-toxic approach to wood preservation

Treesearch

Roger M. Rowell

2006-01-01

Wood can be chemically modified to reduce the moisture content of the cell wall and increases decay resistance. As the level of bonded chemical increases, the cell wall equilibrium moisture content decreases and the resistance to attack by white-and brown-rot fungi increases. There is a direct relationship between the decrease in cell wall moisture Content and...

Effect of moisture on the fatigue behavior of graphite/epoxy composite laminates

NASA Technical Reports Server (NTRS)

Ramani, S. V.; Nelson, H. G.

1979-01-01

The form of the moisture distribution in the specimen (gradient and flat profile) was considered to establish the influence of accelerated moisture conditioning on fatigue behavior. For the gradient specimens having an average moisture content of 1.4 percent, fatigue life was reduced by a factor of 8 at all stress levels investigated. Corresponding reduction in fatigue life for the flat moisture profile specimens at the same average moisture content was comparatively smaller, being about a factor of 5 from the value in dry specimens. X-ray radiographic analysis of damage accumulation in compression-compression fatigue revealed interlaminar cracking to be the dominant mode of failure responsible for the observed enhanced cyclic degradation of moisture-conditioned specimens. This finding was corroborated by the observed systematic reduction in interlaminar shear strength as a function of moisture content, which, in turn, increased the propensity for delamination under cyclic compressive loads. Residual strength measurements on cycled specimens indicated significant strength reductions at long lives, particularly in moisture conditioned specimens.

Roller compaction of moist pharmaceutical powders.

PubMed

Wu, C-Y; Hung, W-L; Miguélez-Morán, A M; Gururajan, B; Seville, J P K

2010-05-31

The compression behaviour of powders during roller compaction is dominated by a number of factors, such as process conditions (roll speed, roll gap, feeding mechanisms and feeding speed) and powder properties (particle size, shape, moisture content). The moisture content affects the powder properties, such as the flowability and cohesion, but it is not clear how the moisture content will influence the powder compression behaviour during roller compaction. In this study, the effect of moisture contents on roller compaction behaviour of microcrystalline cellulose (MCC, Avicel PH102) was investigated experimentally. MCC samples of different moisture contents were prepared by mixing as-received MCC powder with different amount of water that was sprayed onto the powder bed being agitated in a rotary mixer. The flowability of these samples were evaluated in terms of the poured angle of repose and flow functions. The moist powders were then compacted using the instrumented roller compactor developed at the University of Birmingham. The flow and compression behaviour during roller compaction and the properties of produced ribbons were examined. It has been found that, as the moisture content increases, the flowability of moist MCC powders decreases and the powder becomes more cohesive. As a consequence of non-uniform flow of powder into the compaction zone induced by the friction between powder and side cheek plates, all produced ribbons have a higher density in the middle and lower densities at the edges. For the ribbons made of powders with high moisture contents, different hydration states across the ribbon width were also identified from SEM images. Moreover, it was interesting to find that these ribbons were split into two halves. This is attributed to the reduction in the mechanical strength of moist powder compacts with high moisture contents produced at high compression pressures. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Moisture determination in composite materials using positron lifetime techniques

NASA Technical Reports Server (NTRS)

Singh, J. J.; Holt, W. R.; Mock, W., Jr.

1980-01-01

A technique was developed which has the potential of providing information on the moisture content as well as its depth in the specimen. This technique was based on the dependence of positron lifetime on the moisture content of the composite specimen. The positron lifetime technique of moisture determination and the results of the initial studies are described.

Effect of storage conditions on the calorific value of municipal solid waste.

PubMed

Nzioka, Antony Mutua; Hwang, Hyeon-Uk; Kim, Myung-Gyun; Yan, Cao Zheng; Lee, Chang-Soo; Kim, Young-Ju

2017-08-01

Storage conditions are considered to be an important factor as far as waste material characteristics are concerned. This experimental investigation was conducted using municipal solid waste (MSW) with a high moisture content and varying composition of organic waste. The objective of this study was to understand the effect of storage conditions and temperature on the moisture content and calorific value of the waste. Samples were subjected to two different storage conditions and investigated at specified temperatures. The composition of sample materials investigated was varied for each storage condition and temperature respectively. Gross calorific value was determined experimentally while net calorific value was calculated using empirical formulas proposed by other researchers. Results showed minimal changes in moisture content as well as in gross and net calorific values when the samples were subjected to sealed storage conditions. Moisture content reduced due to the ventilation process and the rate of moisture removal increased with a rise in storage temperature. As expected, rate of moisture removal had a positive effect on gross and net calorific values. Net calorific values also increased at varying rates with a simultaneous decrease in moisture content. Experimental investigation showed the effectiveness of ventilation in improving the combustion characteristics of the waste.

Risk management for moisture related effects in dry manufacturing processes: a statistical approach.

PubMed

Quiroz, Jorge; Strong, John; Zhang, Lanju

2016-03-01

A risk- and science-based approach to control the quality in pharmaceutical manufacturing includes a full understanding of how product attributes and process parameters relate to product performance through a proactive approach in formulation and process development. For dry manufacturing, where moisture content is not directly manipulated within the process, the variability in moisture of the incoming raw materials can impact both the processability and drug product quality attributes. A statistical approach is developed using individual raw material historical lots as a basis for the calculation of tolerance intervals for drug product moisture content so that risks associated with excursions in moisture content can be mitigated. The proposed method is based on a model-independent approach that uses available data to estimate parameters of interest that describe the population of blend moisture content values and which do not require knowledge of the individual blend moisture content values. Another advantage of the proposed tolerance intervals is that, it does not require the use of tabulated values for tolerance factors. This facilitates the implementation on any spreadsheet program like Microsoft Excel. A computational example is used to demonstrate the proposed method.

High resolution land surface geophysical parameters estimation from ALOS PALSAR data

USDA-ARS?s Scientific Manuscript database

High resolution land surface geophysical products, such as soil moisture, surface roughness and vegetation water content, are essential for a variety of applications ranging from water management to regional climate predictions. In India high resolution geophysical products, in particular soil moist...

Root Water Uptake and Soil Moisture Pattern Dynamics - Capturing Connections, Controls and Causalities

NASA Astrophysics Data System (ADS)

Blume, T.; Heidbuechel, I.; Hassler, S. K.; Simard, S.; Guntner, A.; Stewart, R. D.; Weiler, M.

2015-12-01

We hypothesize that there is a shift in controls on landscape scale soil moisture patterns when plants become active during the growing season. Especially during the summer soil moisture patterns are not only controlled by soils, topography and related abiotic site characteristics but also by root water uptake. Root water uptake influences soil moisture patterns both in the lateral and vertical direction. Plant water uptake from different soil depths is estimated based on diurnal fluctuations in soil moisture content and was investigated with a unique setup of 46 field sites in Luxemburg and 15 field sites in Germany. These sites cover a range of geologies, soils, topographic positions and types of vegetation. Vegetation types include pasture, pine forest (young and old) and different deciduous forest stands. Available data at all sites includes information at high temporal resolution from 3-5 soil moisture and soil temperature profiles, matrix potential, piezometers and sapflow sensors as well as standard climate data. At sites with access to a stream, discharge or water level is also recorded. The analysis of soil moisture patterns over time indicates a shift in regime depending on season. Depth profiles of root water uptake show strong differences between different forest stands, with maximum depths ranging between 50 and 200 cm. Temporal dynamics of signal strength within the profile furthermore suggest a locally shifting spatial distribution of root water uptake depending on water availability. We will investigate temporal thresholds (under which conditions spatial patterns of root water uptake become most distinct) as well as landscape controls on soil moisture and root water uptake dynamics.

Evaluation of the effect of processing methods on the nutritional and anti-nutritional compositions of two under-utilized Nigerian grain legumes.

PubMed

Oke, M O; Sobowale, S S; Ogunlakin, G O

2013-12-15

The nutritional and anti-nutritional compositions of African Yam Bean (AYB) and Lima bean flours under different processing methods were determined. Nutritional and anti-nutritional properties studied include moisture content, crude protein, crude fibre, ash content, ether extract, carbohydrate, tannin, protease inhibitor and phytate. The moisture content of AYB flours ranged from 9.31 to 9.61% while that of lima beans ranged from 9.32 to 9.56%. There is a significant different among the samples when the unprocessed AYB (control) and the processed AYB were compared. The same trend was also observed with lima bean flours. However, some nutrient did not show significant variations with processing. It was observed that samples of soaked/de-hulled AYB have the least protease inhibitor of 0.73 mg/100 g and it is significantly different from the unprocessed samples. Soaked/de-hulled flours of both AYB and lima beans have the most percentage decrease in anti-nutritional content. Lima bean flours were observed to have higher anti-nutritional content than AYB. The percentage decrease of anti-nutritional factors in the samples is proportionally higher than that of the nutrients. The nutritional and anti-nutritional compositions of the samples suggest that processed African Yam Bean (AYB) and Lima bean flours would have useful application in fabricated foods.

National fire-danger rating system fine-fuel moisture content tables—an Alaskan adaptation.

Treesearch

Richard J. Barney

1969-01-01

Fine-fuel moisture content tables, using dry bulb and dewpoint temperatures as entry data, have been developed for use with the National Fire-Danger Rating System in Alaska. Comparisons have been made which illustrate differences resulting from danger-rating calculations based on these new fine-fuel moisture content tables for the cured, transition, and green...

Investigation of Historic Equilibrium Moisture Content Data from the Forest Products Laboratory

Treesearch

Samuel V. Glass; Samuel L. Zelinka; Jay A. Johnson

2014-01-01

The Forest Products Laboratory (FPL) has provided equilibrium moisture content (EMC) values of wood for given temperature and relative humidity (RH) conditions in various forms over the course of its history, primarily for practical purposes related to drying lumber and controlling moisture content. The FPL EMC data have been widely cited and reprinted, not only in...

The effect of moisture content on the corrosion of fasteners embedded in wood subjected to alkaline copper quaternary treatment

Treesearch

Samuel L. Zelinka; Samuel V. Glass; Dominique Derome

2014-01-01

This paper characterizes the corrosion rate of embedded fasteners as a function of wood moisture content using gravimetric and electrochemical measurements. The results indicated that the corrosion rate increased with moisture content before reaching a plateau. The phases present in the corrosion products, as analyzed using X-ray diffraction, are generally consistent...

Computer programs for adjusting the mechanical properties of 2-inch dimension lumber for changes in moisture content

Treesearch

James W. Evans; Jane K. Evans; David W. Green

1990-01-01

This paper presents computer programs for adjusting the mechanical properties of 2-in. dimension lumber for changes in moisture content. Mechanical properties adjusted are modulus of rupture, ultimate tensile stress parallel to the grain, ultimate compressive stress parallel to the gain, and flexural modulus of elasticity. The models are valid for moisture contents...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2010 CFR

2010-07-01

... moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with an inlet dryer... dryer” AND you have a record of the inlet moisture content and inlet dryer temperature (as required in... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2011 CFR

2011-07-01

... moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with an inlet dryer... dryer” AND you have a record of the inlet moisture content and inlet dryer temperature (as required in... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

Soil moisture influenced the interannual variation in temperature sensitivity of soil organic carbon mineralization in the Loess Plateau

NASA Astrophysics Data System (ADS)

Zhang, Y.; Guo, S.; Zhao, M.; Du, L.; Li, R.; Jiang, J.; Wang, R.; Li, N.

2015-01-01

Temperature sensitivity of SOC mineralization (Q10) determines how strong the feedback from global warming may be on the atmospheric CO2 concentration, thus understanding the factors influencing the interannual variation in Q10 is important to accurately estimate the local soil carbon cycle. In situ SOC mineralization was measured using an automated CO2 flux system (Li-8100) in long-term bare fallow soil in the Loess Plateau (35° 12' N, 107° 40' E) in Changwu, Shaanxi, China form 2008 to 2013. The results showed that the annual cumulative SOC mineralization ranged from 226 to 298 g C m-2 y-1 (mean =253 g C m-2 y-1; CV =13%), annual Q10 ranged from 1.48 to 1.94 (mean =1.70; CV =10%), and annual soil moisture content ranged from 38.6 to 50.7% WFPS (mean =43.8% WFPS; CV =11%), which were mainly affected by the frequency and distribution of precipitation. Annual Q10 showed a negative quadratic correlation with soil moisture. In conclusion, understanding of the relationships between interannual variation in Q10 of SOC mineralization, soil moisture and precipitation is important to accurately estimate the local carbon cycle, especially under the changing climate.

Assessment of Evapotranspiration and Soil Moisture Content Across Different Scales of Observation

PubMed Central

Verstraeten, Willem W.; Veroustraete, Frank; Feyen, Jan

2008-01-01

The proper assessment of evapotranspiration and soil moisture content are fundamental in food security research, land management, pollution detection, nutrient flows, (wild-) fire detection, (desert) locust, carbon balance as well as hydrological modelling; etc. This paper takes an extensive, though not exhaustive sample of international scientific literature to discuss different approaches to estimate land surface and ecosystem related evapotranspiration and soil moisture content. This review presents: (i)a summary of the generally accepted cohesion theory of plant water uptake and transport including a shortlist of meteorological and plant factors influencing plant transpiration;(ii)a summary on evapotranspiration assessment at different scales of observation (sap-flow, porometer, lysimeter, field and catchment water balance, Bowen ratio, scintillometer, eddy correlation, Penman-Monteith and related approaches);(iii)a summary on data assimilation schemes conceived to estimate evapotranspiration using optical and thermal remote sensing; and(iv)for soil moisture content, a summary on soil moisture retrieval techniques at different spatial and temporal scales is presented. Concluding remarks on the best available approaches to assess evapotranspiration and soil moisture content with and emphasis on remote sensing data assimilation, are provided. PMID:27879697

Modeling effects of moisture content and advection on odor causing VOCs volatilization from stored swine manure.

PubMed

Liao, C M; Liang, H M

2000-05-01

Two models for evaluating the contents and advection of manure moisture on odor causing volatile organic compounds (VOC-odor) volatilization from stored swine manure were studied for their ability to predict the volatilization rate (indoor air concentration) and cumulative exposure dose: a MJ-I model and a MJ-II model. Both models simulating depletion of source contaminant via volatilization and degradation based on an analytical model adapted from the behavior assessment model of Jury et al. In the MJ-I model, manure moisture movement was negligible, whereas in the MJ-II model, time-dependent indoor air concentrations was a function of constant manure moisture contents and steady-state moisture advection. Predicted indoor air concentrations and inhaled doses for the study VOC-odors of p-cresol, toluene, and p-xylene varied by up to two to three orders of magnitude depending on the manure moisture conditions. The sensitivity analysis of both models suggests that when manure moisture movement exists, simply MJ-I model is inherently not sufficient to represent a more generally volatilization process, which can even become stringent as moisture content increases. The conclusion illustrates how one needs to include a wide variety of manure moisture values in order to fully assess the complex volatilization mechanisms that are present in a real situation.

Microwave meter for rapid, nondestructive determination of in-shell peanut kernel moisture content from dielectric measurements on cleaned and uncleaned pod samples

USDA-ARS?s Scientific Manuscript database

Microwave Sensing provides a means for nondestructively determining the amount of moisture in materials by sensing the dielectric properties of the material. In this study, dielectric properties of Vidalia onions were analyzed for moisture dependence at 13.36 GHz and 23°C for moisture content betwee...

Comparing jack pine slash and forest floor moisture contents and National Fire Danger Rating System predictions.

Treesearch

Robert M. Loomis; William A. Main

1980-01-01

Relations between certain slash and forest floor moisture contents and the applicable estimated time lag fuel moistures of the National Fire Danger Rating System were investigated for 1-year-old jack pine fuel types in northeastern Minnesota and central Lower Michigan. Only approximate estimates of actual fuel moisture are possible fore the relations determined, thus...

Inventory of File gfs.t06z.sfluxgrbf00.grib2

Science.gov Websites

Volumetric Soil Moisture Content [Fraction] 007 0.1-0.4 m below ground SOILW analysis Volumetric Soil Volumetric Soil Moisture Content [Fraction] 068 1-2 m below ground SOILW analysis Volumetric Soil Moisture analysis Temperature [K] 071 0-0.1 m below ground SOILL analysis Liquid Volumetric Soil Moisture (non

Effect of moisture content on fed batch composting reactor of vegetable and fruit wastes.

PubMed

Jolanun, B; Tripetchkul, S; Chiemchaisri, C; Chaiprasert, P; Towprayoon, S

2005-03-01

Vegetable and fruit wastes mixed with sawdust were composted in a laboratory scale reactor by controlling the waste feeding rate at 21 kg m(-3) day(-1) and aeration rate at 10.6 l m(-3) min(-1). The effects of initial moisture content on organic matter degradation and process performance of fed batch composting were investigated. The absolute amount of removal, removal percentage, and removal rate of dry mass obtained were substantially different among the initial moisture contents. The rapid rise of moisture content and the lowest absolute amount of removal observed were achieved in the 50% condition. The initial moisture content yielding the largest absolute amount of removal in both feeding and curing stage was 30% whereas the removal percentage and rate constant of waste decomposition were highest in the 50% condition. Examined by traditional soil physics method, the moisture content at 50-55% was suitable for satisfying the degree of free air space (65-70%) of compost during the fed batch composting. Most degradable organic matter was mainly consumed in the feeding stage as indicated by a higher removal rate of dry mass in all cases. It is recommended that the initial moisture content of 30% and mode of aeration and agitation should be adopted for achieving practical fed batch composting of vegetable and fruit wastes. The study also demonstrated that the composting kinetics of vegetable and fruit wastes mixed with sawdust can be described by a first order model.

Response of deep soil moisture to land use and afforestation in the semi-arid Loess Plateau, China

NASA Astrophysics Data System (ADS)

Yang, Lei; Wei, Wei; Chen, Liding; Mo, Baoru

2012-12-01

SummarySoil moisture is an effective water source for plant growth in the semi-arid Loess Plateau of China. Characterizing the response of deep soil moisture to land use and afforestation is important for the sustainability of vegetation restoration in this region. In this paper, the dynamics of soil moisture were quantified to evaluate the effect of land use on soil moisture at a depth of 2 m. Specifically, the gravimetric soil moisture content was measured in the soil layer between 0 and 8 m for five land use types in the Longtan catchment of the western Loess Plateau. The land use types included traditional farmland, native grassland, and lands converted from traditional farmland (pasture grassland, shrubland and forestland). Results indicate that the deep soil moisture content decreased more than 35% after land use conversion, and a soil moisture deficit appeared in all types of land with introduced vegetation. The introduced vegetation decreased the soil moisture content to levels lower than the reference value representing no human impact in the entire 0-8 m soil profile. No significant differences appeared between different land use types and introduced vegetation covers, especially in deeper soil layers, regardless of which plant species were introduced. High planting density was found to be the main reason for the severe deficit of soil moisture. Landscape management activities such as tillage activities, micro-topography reconstruction, and fallowed farmland affected soil moisture in both shallow and deep soil layers. Tillage and micro-topography reconstruction can be used as effective countermeasures to reduce the soil moisture deficit due to their ability to increase soil moisture content. For sustainable vegetation restoration in a vulnerable semi-arid region, the plant density should be optimized with local soil moisture conditions and appropriate landscape management practices.

Effective moisture diffusivity and activation energy of rambutan seed under different drying methods to promote storage stability

NASA Astrophysics Data System (ADS)

Ahmad, So'bah; Shamsul Anuar, Mohd; Saleena Taip, Farah; Shamsudin, Rosnah; M, Siti Roha A.

2017-05-01

The effects of two drying methods, oven and microwave drying on the effective moisture diffusivity and activation energy of rambutan seed were studied. Effective moisture diffusivity and activation energy are the main indicators used for moisture movement within the material. Hence, it is beneficial to determine an appropriate drying method to attain a final moisture content of rambutan seed that potentially could be used as secondary sources in the industry. An appropriate final moisture content will provide better storage stability that can extend the lifespan of the rambutan seed. The rambutan seeds were dried with two drying methods (oven and microwave) at two level of the process variables (oven temperature; 40°C and 60°C and microwave power; 250W and 1000W) at constant initial moisture contents. The result showed that a higher value of effective moisture diffusivity and less activation energy were observed in microwave drying compared to oven drying. This finding portrays microwave drying expedites the moisture removal to achieve the required final moisture content and the most appropriate drying method for longer storage stability for rambutan seed. With respect to the process variables; higher oven temperatures and lower microwave powers also exhibit similar trends. Hopefully, this study would provide a baseline data to determine an appropriate drying method for longer storage period for turning waste to by-products.

Computed parameters : moisture content for unbound materials at seasonal monitoring program sites

DOT National Transportation Integrated Search

2000-01-01

Moisture content plays a significant role in the performance of pavements. Variation in the amount of moisture in the subgrade can change the volume of swelling soil, which may result in detrimental deformation of the pavement structure. An increase ...

Design of Moisture Content Detection System

NASA Astrophysics Data System (ADS)

Wang, W. C.; Wang, L.

In this paper, a method for measuring the moisture content of grain was presented based on single chip microcomputer and capacitive sensor. The working principle of measuring moisture content is introduced and a concentric cylinder type of capacitive sensor is designed, the signal processing circuits of system are described in details. System is tested in practice and discussions are made on the various factors affecting the capacitive measuring of grain moisture based on the practical experiments, experiment results showed that the system has high measuring accuracy and good controlling capacity.

Fiber optic moisture sensor with moisture-absorbing reflective target

DOEpatents

Kirkham, Randy R.

1987-01-01

A method and apparatus for sensing moisture changes by utilizing optical fiber technology. One embodiment uses a reflective target at the end of an optical fiber. The reflectance of the target varies with its moisture content and can be detected by a remote unit at the opposite end of the fiber. A second embodiment utilizes changes in light loss along the fiber length. This can be attributed to changes in reflectance of cladding material as a function of its moisture content. It can also be affected by holes or inserts interposed in the cladding material and/or fiber. Changing light levels can also be coupled from one fiber to another in an assembly of fibers as a function of varying moisture content in their overlapping lengths of cladding material.

Evaluation of Crops Moisture Provision by Space Remote Sensing Data

NASA Astrophysics Data System (ADS)

Ilienko, Tetiana

2016-08-01

The article is focused on theoretical and experimental rationale for the use of space data to determine the moisture provision of agricultural landscapes and agricultural plants. The improvement of space remote sensing methods to evaluate plant moisture availability is the aim of this research.It was proved the possibility of replacement of satellite imagery of high spatial resolution on medium spatial resolution which are freely available to determine crop moisture content at the local level. The mathematical models to determine the moisture content of winter wheat plants by spectral indices were developed based on the results of experimental field research and satellite (Landsat, MODIS/Terra, RapidEye, SICH-2) data. The maps of the moisture content in winter wheat plants in test sites by obtained models were constructed using modern GIS technology.

Response of bacteria in wastewater sludge to moisture loss by evaporation and effect of moisture content on bacterial inactivation by ionizing radiation.

PubMed Central

Ward, R L; Yeager, J G; Ashley, C S

1981-01-01

Two studies were carried out to determine the influence of moisture content of the survival of bacteria in raw wastewater sludge. The first study involved the effect of water loss by evaporation on the bacterial population. The second used these dewatered samples to measure the effects of moisture content on the inactivation of bacteria sludge by ionizing radiation. Both studies involved survival measurements of six representative fecally associated bacteria grown separately in sterilized sludge as well as survival data on bacteria indigenous to sludge. Growth of bacteria was stimulated in sludge during the initial phase of moisture removal by evaporation, but the reduction of moisture content below about 50% by weight caused a proportional decrease in bacterial numbers. In comparison with the original sludge, this decrease reached about one-half to one order of magnitude in all dried samples except those containing Proteus mirabilis, which decreased about four orders of magnitude. The rates of inactivation of bacteria by ionizing radiation in sludge were usually modified to some degrees by variations in moisture content. Most bacteria were found to be somewhat protected from ionizing radiation at reduced moisture levels. The largest effect was found with Salmonella typhimurium, whose radiation resistance approximately doubled in dried sludge. However, no excessively large D10 values were found for any bacterial species tested. PMID:6789765

Impact of compost process conditions on organic micro pollutant degradation during full scale composting.

PubMed

Sadef, Yumna; Poulsen, Tjalfe Gorm; Bester, Kai

2015-06-01

Knowledge about the effects of oxygen concentration, nutrient availability and moisture content on removal of organic micro-pollutants during aerobic composting is at present very limited. Impact of oxygen concentration, readily available nitrogen content (NH4(+), NO3(-)), and moisture content on biological transformation of 15 key organic micro-pollutants during composting, was therefore investigated using bench-scale degradation experiments based on non-sterile compost samples, collected at full-scale composting facilities. In addition, the adequacy of bench-scale composting experiments for representing full-scale composting conditions, was investigated using micro-pollutant concentration measurements from both bench- and full-scale composting experiments. Results showed that lack of oxygen generally prevented transformation of organic micro-pollutants. Increasing readily available nitrogen content from about 50 mg N per 100 g compost to about 140 mg N per 100 g compost actually reduced micro-pollutant transformation, while changes in compost moisture content from 50% to 20% by weight, only had minor influence on micro-pollutant transformation. First-order micro-pollutant degradation rates for 13 organic micro-pollutants were calculated using data from both full- and bench-scale experiments. First-order degradation coefficients for both types of experiments were similar and ranged from 0.02 to 0.03 d(-1) on average, indicating that if a proper sampling strategy is employed, bench-scale experiments can be used to represent full-scale composting conditions. Copyright © 2015 Elsevier Ltd. All rights reserved.

The effect of temperature and moisture on electrical resistance, strain sensitivity and crack sensitivity of steel fiber reinforced smart cement composite

NASA Astrophysics Data System (ADS)

Teomete, Egemen

2016-07-01

Earthquakes, material degradations and other environmental factors necessitate structural health monitoring (SHM). Metal foil strain gages used for SHM have low durability and low sensitivity. These factors motivated researchers to work on cement based strain sensors. In this study, the effects of temperature and moisture on electrical resistance, compressive and tensile strain gage factors (strain sensitivity) and crack sensitivity were determined for steel fiber reinforced cement based composite. A rapid increase of electrical resistance at 200 °C was observed due to damage occurring between cement paste, aggregates and steel fibers. The moisture—electrical resistance relationship was investigated. The specimens taken out of the cure were saturated with water and had a moisture content of 9.49%. The minimum electrical resistance was obtained at 9% moisture at which fiber-fiber and fiber-matrix contact was maximum and the water in micro voids was acting as an electrolyte, conducting electrons. The variation of compressive and tensile strain gage factors (strain sensitivities) and crack sensitivity were investigated by conducting compression, split tensile and notched bending tests with different moisture contents. The highest gage factor for the compression test was obtained at optimal moisture content, at which electrical resistance was minimum. The tensile strain gage factor for split tensile test and crack sensitivity increased by decreasing moisture content. The mechanisms between moisture content, electrical resistance, gage factors and crack sensitivity were elucidated. The relations of moisture content with electrical resistance, gage factors and crack sensitivities have been presented for the first time in this study for steel fiber reinforced cement based composites. The results are important for the development of self sensing cement based smart materials.

Vis-NIR hyperspectral imaging in visualizing moisture distribution of mango slices during microwave-vacuum drying.

PubMed

Pu, Yuan-Yuan; Sun, Da-Wen

2015-12-01

Mango slices were dried by microwave-vacuum drying using a domestic microwave oven equipped with a vacuum desiccator inside. Two lab-scale hyperspectral imaging (HSI) systems were employed for moisture prediction. The Page and the Two-term thin-layer drying models were suitable to describe the current drying process with a fitting goodness of R(2)=0.978. Partial least square (PLS) was applied to correlate the mean spectrum of each slice and reference moisture content. With three waveband selection strategies, optimal wavebands corresponding to moisture prediction were identified. The best model RC-PLS-2 (Rp(2)=0.972 and RMSEP=4.611%) was implemented into the moisture visualization procedure. Moisture distribution map clearly showed that the moisture content in the central part of the mango slices was lower than that of other parts. The present study demonstrated that hyperspectral imaging was a useful tool for non-destructively and rapidly measuring and visualizing the moisture content during drying process. Copyright © 2015 Elsevier Ltd. All rights reserved.

Analysis and optimal design of moisture sensor for rice grain moisture measurement

NASA Astrophysics Data System (ADS)

Jain, Sweety; Mishra, Pankaj Kumar; Thakare, Vandana Vikas

2018-04-01

The analysis and design of a microstrip sensor for accurate determination of moisture content (MC) in rice grains based on oven drying technique, this technique is easy, fast and less time-consuming to other techniques. The sensor is designed with low insertion loss, reflection coefficient and maximum gain is -35dB and 5.88dB at 2.68GHz as well as discussed all the parameters such as axial ratio, maximum gain, smith chart etc, which is helpful for analysis the moisture measurement. The variation in percentage of moisture measurement with magnitude and phase of transmission coefficient is investigated at selected frequencies. The microstrip moisture sensor consists of one layer: substrate FR4, thickness 1.638 is simulated by computer simulated technology microwave studio (CST MWS). It is concluded that the proposed sensor is suitable for development as a complete sensor and to estimate the optimum moisture content of rice grains with accurately, sensitivity, compact, versatile and suitable for determining the moisture content of other crops and agriculture products.

Monitoring moisture content, temperature, and humidity in whole-tree pine chip piles

Treesearch

John Klepac; Dana Mitchell; Jason Thompson

2015-01-01

Two whole-tree chip piles were monitored for moisture content, temperature, and relative humidity from October 8th, 2010 to March 16th, 2011 at a location in south Alabama. Initial moisture content samples were collected immediately after chips were delivered to the study location on October 8th for Pile 1 and October 22nd for Pile 2. During pile construction, Lascar...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2013 CFR

2013-07-01

... furnish with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate... criteria of a “dry rotary dryer” AND you have a record of the inlet moisture content and inlet dryer... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

40 CFR 63.1947 - When do I have to comply with this subpart if I own or operate a bioreactor?

Code of Federal Regulations, 2013 CFR

2013-07-01

... initiating liquids addition or within 180 days after achieving a moisture content of 40 percent by weight... achieving a 40 percent moisture content instead of 180 days after liquids addition, use the procedures in § 63.1980(g) and (h) to determine when the bioreactor moisture content reaches 40 percent. (b) If your...

40 CFR 63.1947 - When do I have to comply with this subpart if I own or operate a bioreactor?

Code of Federal Regulations, 2014 CFR

2014-07-01

... initiating liquids addition or within 180 days after achieving a moisture content of 40 percent by weight... achieving a 40 percent moisture content instead of 180 days after liquids addition, use the procedures in § 63.1980(g) and (h) to determine when the bioreactor moisture content reaches 40 percent. (b) If your...

40 CFR 63.1947 - When do I have to comply with this subpart if I own or operate a bioreactor?

Code of Federal Regulations, 2012 CFR

2012-07-01

... initiating liquids addition or within 180 days after achieving a moisture content of 40 percent by weight... achieving a 40 percent moisture content instead of 180 days after liquids addition, use the procedures in § 63.1980(g) and (h) to determine when the bioreactor moisture content reaches 40 percent. (b) If your...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2014 CFR

2014-07-01

... furnish with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate... criteria of a “dry rotary dryer” AND you have a record of the inlet moisture content and inlet dryer... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

40 CFR Table 6 to Subpart Dddd of... - Initial Compliance Demonstrations for Work Practice Requirements

Code of Federal Regulations, 2012 CFR

2012-07-01

... furnish with an inlet moisture content less than or equal to 30 percent (by weight, dry basis) AND operate... criteria of a “dry rotary dryer” AND you have a record of the inlet moisture content and inlet dryer... an inlet moisture content of less than or equal to 25 percent (by weight, dry basis) You meet the...

A Small and Slim Coaxial Probe for Single Rice Grain Moisture Sensing

PubMed Central

You, Kok Yeow; Mun, Hou Kit; You, Li Ling; Salleh, Jamaliah; Abbas, Zulkifly

2013-01-01

A moisture detection of single rice grains using a slim and small open-ended coaxial probe is presented. The coaxial probe is suitable for the nondestructive measurement of moisture values in the rice grains ranging from from 9.5% to 26%. Empirical polynomial models are developed to predict the gravimetric moisture content of rice based on measured reflection coefficients using a vector network analyzer. The relationship between the reflection coefficient and relative permittivity were also created using a regression method and expressed in a polynomial model, whose model coefficients were obtained by fitting the data from Finite Element-based simulation. Besides, the designed single rice grain sample holder and experimental set-up were shown. The measurement of single rice grains in this study is more precise compared to the measurement in conventional bulk rice grains, as the random air gap present in the bulk rice grains is excluded. PMID:23493127

Fiber Optic Thermo-Hygrometers for Soil Moisture Monitoring.

PubMed

Leone, Marco; Principe, Sofia; Consales, Marco; Parente, Roberto; Laudati, Armando; Caliro, Stefano; Cutolo, Antonello; Cusano, Andrea

2017-06-20

This work deals with the fabrication, prototyping, and experimental validation of a fiber optic thermo-hygrometer-based soil moisture sensor, useful for rainfall-induced landslide prevention applications. In particular, we recently proposed a new generation of fiber Bragg grating (FBGs)-based soil moisture sensors for irrigation purposes. This device was realized by integrating, inside a customized aluminum protection package, a FBG thermo-hygrometer with a polymer micro-porous membrane. Here, we first verify the limitations, in terms of the volumetric water content (VWC) measuring range, of this first version of the soil moisture sensor for its exploitation in landslide prevention applications. Successively, we present the development, prototyping, and experimental validation of a novel, optimized version of a soil VWC sensor, still based on a FBG thermo-hygrometer, but able to reliably monitor, continuously and in real-time, VWC values up to 37% when buried in the soil.

Fiber Optic Thermo-Hygrometers for Soil Moisture Monitoring

PubMed Central

Leone, Marco; Principe, Sofia; Consales, Marco; Parente, Roberto; Laudati, Armando; Caliro, Stefano; Cutolo, Antonello; Cusano, Andrea

2017-01-01

This work deals with the fabrication, prototyping, and experimental validation of a fiber optic thermo-hygrometer-based soil moisture sensor, useful for rainfall-induced landslide prevention applications. In particular, we recently proposed a new generation of fiber Bragg grating (FBGs)-based soil moisture sensors for irrigation purposes. This device was realized by integrating, inside a customized aluminum protection package, a FBG thermo-hygrometer with a polymer micro-porous membrane. Here, we first verify the limitations, in terms of the volumetric water content (VWC) measuring range, of this first version of the soil moisture sensor for its exploitation in landslide prevention applications. Successively, we present the development, prototyping, and experimental validation of a novel, optimized version of a soil VWC sensor, still based on a FBG thermo-hygrometer, but able to reliably monitor, continuously and in real-time, VWC values up to 37% when buried in the soil. PMID:28632172

NIR spectroscopic measurement of moisture content in Scots pine seeds.

PubMed

Lestander, Torbjörn A; Geladi, Paul

2003-04-01

When tree seeds are used for seedling production it is important that they are of high quality in order to be viable. One of the factors influencing viability is moisture content and an ideal quality control system should be able to measure this factor quickly for each seed. Seed moisture content within the range 3-34% was determined by near-infrared (NIR) spectroscopy on Scots pine (Pinus sylvestris L.) single seeds and on bulk seed samples consisting of 40-50 seeds. The models for predicting water content from the spectra were made by partial least squares (PLS) and ordinary least squares (OLS) regression. Different conditions were simulated involving both using less wavelengths and going from samples to single seeds. Reflectance and transmission measurements were used. Different spectral pretreatment methods were tested on the spectra. Including bias, the lowest prediction errors for PLS models based on reflectance within 780-2280 nm from bulk samples and single seeds were 0.8% and 1.9%, respectively. Reduction of the single seed reflectance spectrum to 850-1048 nm gave higher biases and prediction errors in the test set. In transmission (850-1048 nm) the prediction error was 2.7% for single seeds. OLS models based on simulated 4-sensor single seed system consisting of optical filters with Gaussian transmission indicated more than 3.4% error in prediction. A practical F-test based on test sets to differentiate models is introduced.

Soil moisture and excavation behaviour in the Chaco leaf-cutting ant (Atta vollenweideri): digging performance and prevention of water inflow into the nest.

PubMed

Pielström, Steffen; Roces, Flavio

2014-01-01

The Chaco leaf-cutting ant Atta vollenweideri is native to the clay-heavy soils of the Gran Chaco region in South America. Because of seasonal floods, colonies are regularly exposed to varying moisture across the soil profile, a factor that not only strongly influences workers' digging performance during nest building, but also determines the suitability of the soil for the rearing of the colony's symbiotic fungus. In this study, we investigated the effects of varying soil moisture on behaviours associated with underground nest building in A. vollenweideri. This was done in a series of laboratory experiments using standardised, plastic clay-water mixtures with gravimetric water contents ranging from relatively brittle material to mixtures close to the liquid limit. Our experiments showed that preference and group-level digging rate increased with increasing water content, but then dropped considerably for extremely moist materials. The production of vibrational recruitment signals during digging showed, on the contrary, a slightly negative linear correlation with soil moisture. Workers formed and carried clay pellets at higher rates in moist clay, even at the highest water content tested. Hence, their weak preference and low group-level excavation rate observed for that mixture cannot be explained by any inability to work with the material. More likely, extremely high moistures may indicate locations unsuitable for nest building. To test this hypothesis, we simulated a situation in which workers excavated an upward tunnel below accumulated surface water. The ants stopped digging about 12 mm below the interface soil/water, a behaviour representing a possible adaptation to the threat of water inflow field colonies are exposed to while digging under seasonally flooded soils. Possible roles of soil water in the temporal and spatial pattern of nest growth are discussed.

Changes in Moisture, Protein, and Fat Content of Fish and Rice Flour Coextrudates during Single-Screw Extrusion Cooking

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaya Shankar Tumuluru; Shahab Sokhansanj; Sukumar Bandyopadhyay

Changes in proximate composition of fish and rice flour coextrudates like moisture, protein, and fat content were studied with respect to extrusion process v ariables like barrel temperature, x1 (100–200 degrees C); screw speed, x2 (70–110 rpm); fish content of the feed, x3 (5–45 percent); and feed moisture content, x4 (20–60 percent). Experiments were conducted at five levels of the process variables based on rotatable experimental design. Response surface models (RSM) were developed that adequately described the changes in moisture, protein, and fat content of the extrudates based on the coeff icient of determination (R2) values of 0.95, 0.99, andmore » 0.94. ANOVA analysis indicated that extrudate moisture content was influenced by x4, protein content by x1 and x3, and fat content by x3 and x4 at P < 0.001. Trends based on response surf ace plots indicated that the x1 of about 200 degrees C, x2 of about 90 rpm, x3 of about 25%, and x4 of about 20% minimized the moisture in the extrudates. Protein content was maximized at x1 of 100 degrees C, x2 > 80 rpm, x3 of about 45 percent, and x4 > 50 percent, and fat content was minimized at x1 of about 200 degrees C, x2 of about 85–95 rpm, x3 < 15 percent, and x4 of about >50 percent. Optimized process variables based on a genetic algorithm (GA) for minimum moisture and fat content and maximum protein content were x1 = 199.86, x2 = 109.86, x3 = 32.45, x4 = 20.03; x1 = 199.71, x2 = 90.09, x3 = 15.27, x4 = 58.47; and x1 = 102.97, x2 = 107.67, x3 = 44.56, x4 = 59.54. The predicted values were 17.52 percent, 0.57 percent, and 46.65 percent. Based on the RSM and GA analy sis, extrudate moisture and protein content was influenced by x1, x3, and x4 and fat content by x2, x3, and x4.« less

Analysis of absorption and spreading of moisturizer on the microscopic region of the skin surface with near-infrared imaging.

PubMed

Arimoto, H; Yanai, M; Egawa, M

2016-11-01

Near-infrared (NIR) light with high water absorption enables us to visualize the water content distribution appeared in the superficial skin layer. The light penetration depth with the wavelength of 1920 nm is almost 100 μm from the skin surface. Thus, the water distribution in the stratum corneum can be effectively imaged by detecting the wavelength band around 1920 nm. The aim of this article was to measure the time-lapse behavior of the tiny droplet of the moisturizer spreading on the skin surface by imaging in 1920 nm wavelength band for investigating the correlation with the traditional index of the skin condition such as the water content and transepidermal water loss (TEWL). Experiment is performed with three moisturizer products and seven volunteer subjects. The NIR image is acquired by an originally designed imaging scope equipped with the white light of the strong brightness [super continuum (SC) light], the bandpass filter with the center wavelength of 1920 nm, and the NIR image sensor. A tiny droplet of the moisturizer is put on the surface of the skin and the time-lapse images are saved. Each acquired image is analyzed from a view point of the droplet area and elapsed time for absorption into the skin. The water content and TEWL of all subjects are measured by the conventional electrical method for investigating the relationship with the measured droplet dynamics parameters. Elapsed time for moisturizer droplet to be absorbed into the skin, the droplet area just before absorption for three moisturizer products, skin water contents, and TEWL for seven subjects were measured and correlation coefficients for each parameters were calculated. It was found that the skin with higher water contents or lower TEWL absorbed the moisturizer faster and spreads moisturizer wider. Also absorption and spreading speed depend on moisturizer property (moisturizing or fresh) which is originated from the moisturizer constituents. The correlation values between the moisturizer dynamics on the skin surface and the traditional index of the skin property were clarified. It was found that the skin with the high water content or low TEWL absorbs the moisturizer droplet fast. The spreading area depends not only on the skin property but on the constituents of the moisturizers. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Significance of heat-moisture treatment conditions on the pasting and gelling behaviour of various starch-rich cereal and pseudocereal flours.

PubMed

Collar, Concha

2017-10-01

The impact of heat-moisture treatment processing conditions (15%, 25%, and 35% moisture content; 1, 3, and 5 h heating time at 120 ℃) on the viscosity pasting and gelling profiles of different grain flours matrices (barley, buckwheat, sorghum, high β-glucan barley, and wheat) was investigated by applying successive cooking and cooling cycles to rapid visco analyser canisters with highly hydrated samples (3.5:25, w:w). At a milder heat-moisture treatment conditions (15% moisture content, 1 h heating time), except for sorghum, heat-moisture treatment flours reached much higher viscosity values during earlier pasting and subsequent gelling than the corresponding native counterparts. Besides heat-moisture treatment wheat flour, the described behaviour found also for non-wheat-treated flours has not been previously reported in the literature. An increased hydrophobicity of prolamins and glutelins in low moisture-short heating time heat-moisture treatment of non-wheat flours with high protein content (12.92%-19.95%) could explain the enhanced viscosity profile observed.

Relative performance evaluation of a custom-made near infrared reflectance instrument and two commercial instruments (Foss and ASD) in the nondestructive moisture content measurement of in-shell peanuts

USDA-ARS?s Scientific Manuscript database

A custom made Near Infrared Reflectance (NIR) spectroscope was used to determine the moisture content of in-shell peanuts of Virginia type peanuts. Peanuts were conditioned to different moisture levels between 6 and 26 % (wet basis) and samples from different moisture levels were separated into two...

Photoacoustic spectroscopy and thermal relaxation method to evaluate corn moisture content

NASA Astrophysics Data System (ADS)

Pedrochi, F.; Medina, A. N.; Bento, A. C.; Baesso, M. L.; Luz, M. L. S.; Dalpasquale, V. A.

2005-06-01

In this study, samples of popcorn with different degrees of moisture were analyzed. The optical absorption bands at the mid infrared were measured using photoacoustic spectroscopy and were correlated to the sample moisture. The results were in agreement with moisture data determined by the well known reference method, the Karl Fischer. In addition, the thermal relaxation method was used to determine the sample specific heat as a function of the moisture content. The results were also in agreement with the two mentioned methods.

Characterization of recycled rubber media for hydrogen sulphide (H2S) control.

PubMed

Wang, Ning; Park, Jaeyoung; Evans, Eric A; Ellis, Timothy G

2014-01-01

Hydrogen sulphide (H2S) adsorption capacities on recycled rubber media, tyre-derived rubber particle (TDRP), and other rubber material (ORM) have been evaluated. As part of the research, densities, moisture contents, and surface properties of TDRP and ORM have been determined. The research team findings show that TDRP and ORM are more particulate in nature and not highly porous-like activated carbon. The characteristics of surface area, pore size, and moisture content support chemisorption on the macrosurface rather than physical adsorption in micropores. For example, moisture content is essential for H2S adsorption on ORM, and an increase in moisture content results in an increase in adsorption capacity.

Retrieval of Soil Moisture and Roughness from the Polarimetric Radar Response

NASA Technical Reports Server (NTRS)

Sarabandi, Kamal; Ulaby, Fawwaz T.

1997-01-01

The main objective of this investigation was the characterization of soil moisture using imaging radars. In order to accomplish this task, a number of intermediate steps had to be undertaken. In this proposal, the theoretical, numerical, and experimental aspects of electromagnetic scattering from natural surfaces was considered with emphasis on remote sensing of soil moisture. In the general case, the microwave backscatter from natural surfaces is mainly influenced by three major factors: (1) the roughness statistics of the soil surface, (2) soil moisture content, and (3) soil surface cover. First the scattering problem from bare-soil surfaces was considered and a hybrid model that relates the radar backscattering coefficient to soil moisture and surface roughness was developed. This model is based on extensive experimental measurements of the radar polarimetric backscatter response of bare soil surfaces at microwave frequencies over a wide range of moisture conditions and roughness scales in conjunction with existing theoretical surface scattering models in limiting cases (small perturbation, physical optics, and geometrical optics models). Also a simple inversion algorithm capable of providing accurate estimates of soil moisture content and surface rms height from single-frequency multi-polarization radar observations was developed. The accuracy of the model and its inversion algorithm is demonstrated using independent data sets. Next the hybrid model for bare-soil surfaces is made fully polarimetric by incorporating the parameters of the co- and cross-polarized phase difference into the model. Experimental data in conjunction with numerical simulations are used to relate the soil moisture content and surface roughness to the phase difference statistics. For this purpose, a novel numerical scattering simulation for inhomogeneous dielectric random surfaces was developed. Finally the scattering problem of short vegetation cover above a rough soil surface was considered. A general scattering model for grass-blades of arbitrary cross section was developed and incorporated in a first order random media model. The vegetation model and the bare-soil model are combined and the accuracy of the combined model is evaluated against experimental observations from a wheat field over the entire growing season. A complete set of ground-truth data and polarimetric backscatter data were collected. Also an inversion algorithm for estimating soil moisture and surface roughness from multi-polarized multi-frequency observations of vegetation-covered ground is developed.

In vitro and in vivo assessment of the effect of initial moisture content and drying temperature on the feeding value of maize grain.

PubMed

Huart, F; Malumba, P; Odjo, S; Al-Izzi, W; Béra, F; Beckers, Y

2018-06-11

1. This study assessed the impact of drying temperature (54, 90, and 130°C) and maize grain moisture content at harvest (36% and 29%) on in vitro digestibility, the growth performance and ileal digestibility of broiler chickens. 2. In contrast to the results from the in vitro digestibility, apparent ileal digestibility of starch and energy decreased when the drying temperature was raised from 54 to 130°C, and this effect was more pronounced in maize grain harvested at high initial moisture content (36%). Ileal protein digestibility of maize grain decreased significantly when dried at the intermediate temperature (90°C) and with a high harvest moisture content (36%). Drying temperature and initial moisture content did not significantly affect AMEn. 3. When maize was dried at 130°C, the particle sizes of flour recovered after standard milling procedures decreased significantly, which would influence animal growth performance and in vivo digestibility through animal feed selection.

Performance of a Microwave Bale Moisture Content Meter

USDA-ARS?s Scientific Manuscript database

Measuring the moisture content of cotton bales has been a topic of intense interest in the last few years. A non-contact microwave-based bale moisture meter, Vomax 851-B (Vomax Instrumentation through Samuel Jackson, Lubbock, TX) has been commercially available but independent verification of these...

An Automated Sample Divider for Farmers Stock Peanuts

USDA-ARS?s Scientific Manuscript database

In-shell peanuts are harvested, loaded into drying trailers, and delivered to a central facility where they are dried to a moisture content safe for long term storage, sampled, graded, then unloaded into bulk storage. Drying trailers have capacities ranging from five to twenty-five tons of dry farme...

An automated sample divider for farmers stock peanuts

USDA-ARS?s Scientific Manuscript database

In-shell peanuts are harvested, loaded into drying trailers, and delivered to a central facility where they are dried to a moisture content safe for long term storage, sampled, graded, then unloaded into bulk storage. Drying trailers have capacities ranging from five to twenty-five tons of dry farme...

Influence of spore moisture content on the dry-heat resistance of Bacillus subtilis var. niger.

PubMed

Angelotti, R; Maryanski, J H; Butler, T F; Peeler, J T; Campbell, J E

1968-05-01

The dry-heat resistance of Bacillus subtilis var. niger spores located in or on various materials was determined as D and z values in the range of 105 through 160 C. The systems tested included spores located on steel and paper strips, spores located between stainless-steel washers mated together under 150 inch-lb and 12 inch-lb of torque, and spores encapsulated in methylmethacrylate and epoxy plastics. D values for a given temperature varied with the test system. High D values were observed for the systems in which spores were encapsulated or under heavy torque, whereas lower D values were observed for the steel and paper strip systems and the lightly torqued system. Similar z values were obtained for the plastic and steel strip systems (z(D) = 21 C), but an unusually low z for spores on paper (z(D) = 12.9 C) and an unusually high z for spores on steel washers mated at 150 inch-lb of torque (z(D) = 32 C) were observed. The effect of spore moisture content on the D value of spores encapsulated in water-impermeable plastic was determined, and maximal resistance was observed for spores with a water activity (a(w)) of 0.2 to 0.4. Significantly decreased D values were observed for spores with moisture contents below a(w) 0.2 or above a(w) 0.4. The data indicate that the important factors to be considered when measuring the dry heat resistance of spores are (i) the initial moisture content of the spore, (ii) the rate of spore desiccation during heating, (iii) the water retention capacity of the material in or on which spores are located, and (iv) the relative humidity of the system at the test temperature.

Estimation of Moisture Content of Forest Canopy and Floor from SAR Data Part I: Volume Scattering Case

NASA Technical Reports Server (NTRS)

Moghaddam, M.; Saatchi, S.

1996-01-01

To understand and predict the functioning of forest biomes, their interaction with the atmosphere, and their growth rates, the knowledge of moisture content of their canopy and the floor soil is essential. The synthetic aperture radar on airborne and spaceborne platforms has proven to be a flexible tool for measuring electromagnetic back- scattering properties of vegetation related to their moisture content.

Time to ignition is influenced by both moisture content and soluble carbohydrates in live Douglas fir and Lodgepole pine needles

Treesearch

Matt Jolly; Sara McAllister; Mark Finney; Ann Hadlow

2010-01-01

Living plants are often the primary fuels burning in wildland fire but little is known about the factors that govern their ignition behavior. Moisture content has long been hypothesized to determine the characteristics of fires spreading in live fuels but moisture content alone fails to explain observed differences in the ignition of various species at different times...

A numerical investigation of the influence of radiation and moisture content on pyrolysis and ignition of a leaf-like fuel element

Treesearch

B.L. Yashwanth; B. Shotorban; S. Mahalingam; C.W. Lautenberger; David Weise

2016-01-01

The effects of thermal radiation and moisture content on the pyrolysis and gas phase ignition of a solid fuel element containing high moisture content were investigated using the coupled Gpyro3D/FDS models. The solid fuel has dimensions of a typical Arctostaphylos glandulosa leaf which is modeled as thin cellulose subjected to radiative heating on...

Evaluation and modeling of aerodynamic properties of mung bean seeds

NASA Astrophysics Data System (ADS)

Shahbazi, Feizollah

2015-01-01

Aerodynamic properties of solid materials have long been used to convey and separate seeds and grains during post harvest operations. The objective of this study was the evaluation of the aerodynamic properties of mung bean seeds as a function of moisture content and two grades referred to above and below a cut point of 4.8 mm in length. The results showed that as the moisture content increased from 7.8 to 25% (w.b.), the terminal velocity of seeds increased following a polynomial relationship, from 7.28 to 8.79 and 6.02 to 7.12 m s-1, for grades A and B, respectively. Seeds at grade A had terminal velocities with a mean value of 8.05 m s-1, while at grade B had a mean value of 6.46 m s-1. The Reynolds number of both grades increased linearly with the increase of seeds moisture content, while the drag coefficient decreased with the increase of moisture content. Mathematical relationships were developed to relate the change in seeds moisture content with the obtained values of aerodynamic properties. The analysis of variance showed that moisture content had a significant effect, at 1% probability level, on all the aerodynamics properties of mung beans.

Dropping macadamia nuts-in-shell reduces kernel roasting quality.

PubMed

Walton, David A; Wallace, Helen M

2010-10-01

Macadamia nuts ('nuts-in-shell') are subjected to many impacts from dropping during postharvest handling, resulting in damage to the raw kernel. The effect of dropping on roasted kernel quality is unknown. Macadamia nuts-in-shell were dropped in various combinations of moisture content, number of drops and receiving surface in three experiments. After dropping, samples from each treatment and undropped controls were dry oven-roasted for 20 min at 130 °C, and kernels were assessed for colour, mottled colour and surface damage. Dropping nuts-in-shell onto a bed of nuts-in-shell at 3% moisture content or 20% moisture content increased the percentage of dark roasted kernels. Kernels from nuts dropped first at 20%, then 10% moisture content, onto a metal plate had increased mottled colour. Dropping nuts-in-shell at 3% moisture content onto nuts-in-shell significantly increased surface damage. Similarly, surface damage increased for kernels dropped onto a metal plate at 20%, then at 10% moisture content. Postharvest dropping of macadamia nuts-in-shell causes concealed cellular damage to kernels, the effects not evident until roasting. This damage provides the reagents needed for non-enzymatic browning reactions. Improvements in handling, such as reducing the number of drops and improving handling equipment, will reduce cellular damage and after-roast darkening. Copyright © 2010 Society of Chemical Industry.

Non-destructive Moisture Content Measurement of Bioabsorbable Polymers Used in Medical Implants

NASA Astrophysics Data System (ADS)

Carroll, P. A.; Bell, S. A.; Maxwell, A. S.; Tomlins, P. E.

2012-09-01

Measurements have been made that link moisture content to the degradation of a bioabsorbable polymeric material, poly ( dl-lactide- co-glycolide) (PLGA). Bioabsorbable polymers used in medical implants degrade and are absorbed into the body. In the course of degradation, these polymers absorb water. Progressive non-destructive laboratory measurements of moisture content can be used as a means of tracking changes in these materials over the course of their degradation. Measurements of moisture content were made using a non-destructive microwave resonance instrument. The measurement approach, more usually applied to granular materials, was adapted to measure small, individual solid samples that do not fill the conventional sample volume of the resonator. Using the microwave resonance technique, gains in moisture content were measurable in increasingly degraded samples. The results were confirmed using alternative (destructive) measurements of sample moisture content. The microwave resonance technique offers a non-destructive measurement that can be used to study the degradation characteristics of PLGA. Better understanding of the degradation process can enable the polymer break-down rate to be tailored to match the healing rate of tissue. Non-destructive measurement allows effective study using single rather than multiple samples. This is a strong advantage when novel materials under study may be either expensive or in strictly limited availability.

Effect of process variables on the quality characteristics of pelleted wheat distiller's dried grains with solubles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaya Shankar Tumuluru; Lope Tabil; Anthony Opoku

2011-04-01

The rapid expansion of ethanol processing plants in Canada has resulted in a significant increase in the production of wheat-based distiller's dried grains with solubles (DDGS). Transportation and flowability problems associated with DDGS necessitate investigations on pelleting. In the present study, the effect of process variables like die temperature (T) and feed moisture content (Mw) on the pellet properties like pellet moisture content, durability and pellet density was explored using a single pelleting machine; further studies on pelleting DDGS using a pilot-scale pellet mill were also conducted to understand the effect of die diameter and steam conditioning on durability andmore » bulk density of pellets. Proximate analysis of DDGS indicated that crude protein and dry matter were in the range of 37.37–40.33% and 91.27–92.60%, respectively. Linear regression models developed for pellet quality attributes like pellet moisture content, pellet density and durability adequately described the single pelleting process with R2 value of 0.97, 0.99 and 0.7, respectively. ANOVA results have indicated that linear terms T and Mw and the interaction term T × Mw were statistically significant at P < 0.01 and P < 0.1 for pellet moisture content and pellet density. Based on the trends of the surface plots, a medium T of about 50–80 °C and a low Mw of about 5.1% resulted in maximum pellet density and durability and minimum pellet moisture content. Results from pilot-scale studies indicated that bulk density, durability and throughput values were 436.8–528.9 kg m-3, 60.3–92.7% and 45.52–68.77 kg h-1, respectively. It was observed that both die diameter and steam addition had a significant effect on the bulk density and the durability values. The highest bulk density and durability were achieved with 6.4 mm die diameter with steam addition compared to 7.9 mm die with or without steam addition.« less

Temporal and spatial variabilities in the surface moisture content of a fine-grained beach

NASA Astrophysics Data System (ADS)

Namikas, S. L.; Edwards, B. L.; Bitton, M. C. A.; Booth, J. L.; Zhu, Y.

2010-01-01

This study examined spatial and temporal variations in the surface moisture content of a fine-grained beach at Padre Island, Texas, USA. Surface moisture measurements were collected on a 27 × 24 m grid that extended from the dune toe to the upper foreshore. The grid was surveyed at 2 to 4 h intervals for two tidal cycles, generating 17 maps of the spatial distribution of surface moisture. Simultaneous measurements of air temperature and humidity, wind speed and direction, tidal elevation, and water table elevation were used to interpret observed changes in surface moisture. It was found that the spatial distribution of surface moisture was broadly characterized by a cross-shore gradient of high to low content moving landward from the swash zone. The distribution of surface moisture was conceptualized in terms of three zones: saturated (> 25%), intermediate or transitional (5-25%), and dry (< 5%). The position of the saturated zone corresponded to the uppermost swash zone and therefore shifted in accordance with tidal elevation. Moisture contents in the intermediate and dry zones were primarily related to variation in water table depth (which was in turn controlled by tidal elevation) and to a lesser extent by evaporation. Signals associated with atmospheric processes such as evaporation were muted by the minimal degree of variation in atmospheric parameters experienced during most of the study period, but were apparent for the last few hours. The observed spatial and temporal variations in moisture content correspond reasonably well with observations of key controlling processes, but more work is needed to fully characterize this process suite.

Factors influencing moisture analysis in the 3013 destructive examination surveillance program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scogin, J. H.

Thermogravimetric analysis of a solid sample with mass spectrometry (TGA-MS) of the evolved gas is used in the destructive examination (DE) portion of the Integrated Surveillance Program to quantify the moisture content of the material stored in a 3013 container. As with any measurement determined from a small sample, the collection, storage, transportation, and handling of the sample can affect its ability to represent the properties of the bulk material. During the course of the DE program, questions have periodically arisen concerning the ability of the moisture sample to reflect reliably the actual moisture content of the entire material storedmore » in the 3013 container. Most concerns are related to the ability to collect a representative sample and to preserve the moisture content of the sample between collection and analysis. Recent delays in analysis caused by maintenance issues with the TGA-MS instrument presented a unique opportunity to document and quantify the effects various factors have on the TGA-MS moisture measurement. This report will use recent data to document the effects that current sample collection and handling practices have on the TGA-MS moisture measurement. Some suggestions will be made which could improve the current sample collection and handling practices for the TGA-MS moisture measurement so that the analytical results more accurately reflect the moisture content of the material stored in the 3013 container.« less

Modeling moisture content of fine dead wildland fuels: Input to the BEHAVE fire prediction system

Treesearch

Richard C. Rothermel; Ralph A. Wilson; Glen A. Morris; Stephen S. Sackett

1986-01-01

Describes a model for predicting moisture content of fine fuels for use with the BEHAVE fire behavior and fuel modeling system. The model is intended to meet the need for more accurate predictions of fine fuel moisture, particularly in northern conifer stands and on days following rain. The model is based on the Canadian Fine Fuel Moisture Code (FFMC), modified to...

Dilatometric measurement of the partial molar volume of water sorbed to durum wheat flour.

PubMed

Hasegawa, Ayako; Ogawa, Takenobu; Adachi, Shuji

2013-01-01

Moisture sorption isotherms were measured at 25 °C for untreated, dry-heated and pre-gelatinized durum wheat flour samples. The isotherms could be expressed by the Guggenheim-Anderson-de Boer equation. The amount of water sorbed to the untreated flour was highest for low water activity, with water sorbed to the pre-gelatinized and dry-heated flour samples following. The dry-heated and pregelatinized flour samples exhibited the same dependence of the moisture content on the partial molar volume of water at 25 °C as the untreated flour. The partial molar volume of water was ca. 9 cm(3)/mol at a moisture content of 0.03 kg-H2O/kg-d.m. The volume increased with increasing moisture content, and reached a constant value of ca. 17.5 cm(3)/mol at a moisture content of 0.2 kg-H2O/kg-d.m. or higher.

Influence of Initial Moisture Content on Heat and Moisture Transfer in Firefighters' Protective Clothing

PubMed Central

He, Song

2017-01-01

This paper presents a model for heat and moisture transfer through firefighters' protective clothing (FPC) during radiation exposure. The model, which accounts for air gaps in the FPC as well as heat transfer through human skin, investigates the effect of different initial moisture contents on the thermal insulation performance of FPC. Temperature, water vapor density, and the volume fraction of liquid water profiles were monitored during the simulation, and the heat quantity absorbed by water evaporation was calculated. Then the maximum durations of heat before the wearer acquires first- and second-degree burns were calculated based on the bioheat transfer equation and the Henriques equation. The results show that both the moisture weight in each layer and the total moisture weight increase linearly within a given environmental humidity level. The initial moisture content in FPC samples significantly influenced the maximum water vapor density. The first- and second-degree burn injury time increase 16 sec and 18 sec when the RH increases from 0% to 90%. The total quantity of heat accounted for by water evaporation was about 10% when the relative humidity (RH) is 80%. Finally, a linear relationship was identified between initial moisture content and the human skin burn injury time before suffering first- and second-degree burn injuries. PMID:28466066

Influence of Initial Moisture Content on Heat and Moisture Transfer in Firefighters' Protective Clothing.

PubMed

Huang, Dongmei; He, Song

2017-01-01

This paper presents a model for heat and moisture transfer through firefighters' protective clothing (FPC) during radiation exposure. The model, which accounts for air gaps in the FPC as well as heat transfer through human skin, investigates the effect of different initial moisture contents on the thermal insulation performance of FPC. Temperature, water vapor density, and the volume fraction of liquid water profiles were monitored during the simulation, and the heat quantity absorbed by water evaporation was calculated. Then the maximum durations of heat before the wearer acquires first- and second-degree burns were calculated based on the bioheat transfer equation and the Henriques equation. The results show that both the moisture weight in each layer and the total moisture weight increase linearly within a given environmental humidity level. The initial moisture content in FPC samples significantly influenced the maximum water vapor density. The first- and second-degree burn injury time increase 16 sec and 18 sec when the RH increases from 0% to 90%. The total quantity of heat accounted for by water evaporation was about 10% when the relative humidity (RH) is 80%. Finally, a linear relationship was identified between initial moisture content and the human skin burn injury time before suffering first- and second-degree burn injuries.

Effect of moisture content on the heating profile in composted broiler litter

USDA-ARS?s Scientific Manuscript database

Moisture content can affect the magnitude of heat generation during composting. Temperature was recorded every 2 min for 7 d at 10-cm increments throughout the vertical profile of broiler litter treated with five quantities of water addition. Water additions were applied to achieve litter moisture...

Effects of Starting Moisture on Characteristics of Oil Roasted Peanut

USDA-ARS?s Scientific Manuscript database

Previous research has shown that the moisture content of peanuts before dry roasting affects the quality of the finished product. This study demonstrates the effects of the starting moisture content of the raw product on peanuts that were oil roasted. Scanning Electron Microscope images taken befo...

Modeling the use of microwave energy in sensing of moisture content in vidalia onions

USDA-ARS?s Scientific Manuscript database

Microwave moisture sensing provides a means to nondestructively determine the amount of water in materials. This is accomplished through the correlation of dielectric constant and loss factor with moisture content in the material. In this study, linear relationships between a density-independent fun...

Moisture effects on the prediction performance of a single kernel near-infrared deoxynivalenol calibration

USDA-ARS?s Scientific Manuscript database

Effect of moisture content variation on the accuracy of single kernel deoxynivalenol (DON) prediction by near-infrared (NIR) spectroscopy was investigated. Sample moisture content (MC) considerably affected accuracy of the current NIR DON calibration by underestimating or over estimating DON at high...

Testate amoebae communities sensitive to surface moisture conditions in Patagonian peatlands

NASA Astrophysics Data System (ADS)

Loisel, J.; Booth, R.; Charman, D.; van Bellen, S.; Yu, Z.

2017-12-01

Here we examine moss surface samples that were collected during three field campaigns (2005, 2010, 2014) across southern Patagonian peatlands to assess the potential use of testate amoebae and 13C isotope data as proxy indicators of soil moisture. These proxies have been widely tested across North America, but their use as paleoecological tools remains sparse in the southern hemisphere. Samples were collected along a hydrological gradient spanning a range of water table depth from 0cm in wet hollows to over 85cm in dry hummocks. Moss moisture content was measured in the field. Over 25 taxa were identified, with many of them not found in North America. Ordinations indicate statistically significant and dominant effects of soil moisture and water table depth on testate assemblages, though interestingly 13C is even more strongly correlated with testates amoebae than direct soil conditions. It is possible that moss 13C signature constitutes a compound indicator that represents seasonal soil moisture better than opportunistic sampling during field campaigns. There is no significant effect of year or site across the dataset. In addition to providing a training set that translates testate amoebae moisture tolerance range into water tabel depth for Patagonian peatlands, we also compare our results with those from the North American training set to show that, despite 'novel' Patagonian taxa, the robustness of international training sets is probably sufficient to quantify most changes in soil moisture from any site around the world. We also identify key indicator species that are shown to be of universal value in peat-based hydrological reconstructions.

The critical micelle concentration of lecithin in bulk oils and medium chain triacylglycerol is influenced by moisture content and total polar materials.

PubMed

Kim, JiSu; Kim, Mi-Ja; Lee, JaeHwan

2018-09-30

Effects of different moisture contents and oxidised compounds on the critical micelle concentration (CMC) of lecithin were determined in bulk oils and in medium-chain triacylglycerols (MCT). CMC of lecithin in MCT was significantly higher than that in other vegetable oils including olive, soybean, corn, and rapeseed oils (p < 0.05). Presence of moisture significantly affected the CMC of lecithin in MCT (p < 0.05). CMC of lecithin was high when the moisture content was below 900 ppm, whereas at a moisture content of 1000 ppm, CMC of lecithin decreased significantly (p < 0.05), and then started to increase. Addition of total polar materials (TPM), which are oxidation products, at 3 and 5% concentrations, decreased CMC of lecithin significantly (p < 0.05) in MCT, compared to when 0, 1, and 1.5% of TPM was added to MCT. As the degree of oxidation increased in corn oil, CMC of lecithin gradually decreased. Additionally, under different moisture contents, corn oils showed a similar pattern of CMC of lecithin in MCT, whereas oxidised corn oil had a little lower CMC of lecithin than unoxidised corn oil. The results clearly showed that the concentration of lecithin for the formation of micelles is greatly influenced by the presence of oxidation products and the moisture content in bulk oils. Copyright © 2018 Elsevier Ltd. All rights reserved.

Organic petrology and coalbed gas content, Wilcox Group (Paleocene-Eocene), northern Louisiana

USGS Publications Warehouse

Hackley, Paul C.; Warwick, Peter D.; Breland, F. Clayton

2007-01-01

Wilcox Group (Paleocene–Eocene) coal and carbonaceous shale samples collected from four coalbed methane test wells in northern Louisiana were characterized through an integrated analytical program. Organic petrographic analyses, gas desorption and adsorption isotherm measurements, and proximate–ultimate analyses were conducted to provide insight into conditions of peat deposition and the relationships between coal composition, rank, and coalbed gas storage characteristics. The results of petrographic analyses indicate that woody precursor materials were more abundant in stratigraphically higher coal zones in one of the CBM wells, consistent with progradation of a deltaic depositional system (Holly Springs delta complex) into the Gulf of Mexico during the Paleocene–Eocene. Comparison of petrographic analyses with gas desorption measurements suggests that there is not a direct relationship between coal type (sensu maceral composition) and coalbed gas storage. Moisture, as a function of coal rank (lignite–subbituminous A), exhibits an inverse relationship with measured gas content. This result may be due to higher moisture content competing for adsorption space with coalbed gas in shallower, lower rank samples. Shallower (< 600 m) coal samples consistently are undersaturated with respect to CH4 adsorption isotherms; deeper (> 600 m) coal samples containing less moisture range from under- to oversaturated with respect to their CH4adsorption capacity.

Simultaneous preservation of orchid seed and its fungal symbiont using encapsulation-dehydration is dependent on moisture content and storage temperature.

PubMed

Wood, C B; Pritchard, H W; Miller, A P

2000-01-01

Seeds of Dactylorhiza fuchsii (common spotted orchid) and Anacamptis morio (green-winged orchid) were encapsulated in alginate beads with hyphae of the basidomycete fungus Ceratobasidium cornigerum. Pre-treatment of beads for 18 h with sucrose at an optimum concentration of 0.75 M decreased the desiccation rate in a flow of sterile air (c. 23 degree C, 30% RH) and increased seed and fungal survival after up to 16 h drying. Pre-treated and 16-h dried beads were transferred to cryo-vials and subsequently stored at a range of low temperatures for up to 30 d. Neither embryo growth of both orchids nor fungal development was detrimentally affected by 1 d storage at -196 degree C when the beads were pre-dried to c. 20% moisture content. Encapsulated D. fuchsii seed and compatible fungus had < 5% and < 45% viability when beads of the same moisture content were stored for 1 d at -20 degree C and -70 degree C respectively. In contrast, viability of the seed and the fungus remained unchanged during 30 days storage at -196 degree C but was progressively lost at 16 degree C over the same interval. The results indicate opportunities for the use of simultaneous cryopreservation as a conservation tool for diverse taxa.

Fiber optic moisture sensor

DOEpatents

Kirkham, R.R.

1984-08-03

A method and apparatus for sensing moisture changes by utilizing optical fiber technology. One embodiment uses a reflective target at the end of an optical fiber. The reflectance of the target varies with its moisture content and can be detected by a remote unit at the opposite end of the fiber. A second embodiment utilizes changes in light loss along the fiber length. This can be attributed to changes in reflectance of cladding material as a function of its moisture content. It can also be affected by holes or inserts interposed in the cladding material and/or fiber. Changing light levels can also be coupled from one fiber to another in an assembly of fibers as a function of varying moisture content in their overlapping lengths of cladding material.

[Soil moisture dynamics of artificial Caragana microphylla shrubs at different topographical sites in Horqin sandy land].

PubMed

Huang, Gang; Zhao, Xue-yong; Huang, Ying-xin; Su, Yan-gui

2009-03-01

Based on the investigation data of vegetation and soil moisture regime of Caragana microphylla shrubs widely distributed in Horqin sandy land, the spatiotemporal variations of soil moisture regime and soil water storage of artificial sand-fixing C. microphylla shrubs at different topographical sites in the sandy land were studied, and the evapotranspiration was measured by water balance method. The results showed that the soil moisture content of the shrubs was the highest in the lowland of dunes, followed by in the middle, and in the crest of the dunes, and increased with increasing depth. No water stress occurred during the growth season of the shrubs. Soil moisture content of the shrubs was highly related to precipitation event, and the relationship of soil moisture content with precipitation was higher in deep soil layer (50-180 cm) than in shallow soil layer (0-50 cm). The variation coefficient of soil moisture content was also higher in deep layer than in shallow layer. Soil water storage was increasing in the whole growth season of the shrubs, which meant that the accumulation of soil water occurred in this area. The evapotranspiriation of the shrubs occupied above 64% of the precipitation.

9 CFR 319.760 - Deviled ham, deviled tongue, and similar products.

Code of Federal Regulations, 2012 CFR

2012-01-01

...: Provided, That the total fat content shall not exceed 35 percent of the finished product. The moisture content of deviled ham shall not exceed that of the fresh unprocessed meat. (b) The moisture content of...

9 CFR 319.760 - Deviled ham, deviled tongue, and similar products.

Code of Federal Regulations, 2014 CFR

2014-01-01

...: Provided, That the total fat content shall not exceed 35 percent of the finished product. The moisture content of deviled ham shall not exceed that of the fresh unprocessed meat. (b) The moisture content of...

Recycled wind turbine blades as a feedstock for second generation composites.

PubMed

Mamanpush, Seyed Hossein; Li, Hui; Englund, Karl; Tabatabaei, Azadeh Tavousi

2018-06-01

With an increase in renewable wind energy via turbines, an underlying problem of the turbine blade disposal is looming in many areas of the world. These wind turbine blades are predominately a mixture of glass fiber composites (GFCs) and wood and currently have not found an economically viable recycling pathway. This work investigates a series of second generation composites fabricated using recycled wind turbine material and a polyurethane adhesive. The recycled material was first comminuted via a hammer-mill through a range of varying screen sizes, resinated and compressed to a final thickness. The refined particle size, moisture content and resin content were assessed for their influence on the properties of recycled composites. Static bending, internal bond and water sorption properties were obtained for all composites panels. Overall improvement of mechanical properties correlated with increase in resin content, moisture content, and particle size. The current investigation demonstrates that it is feasible and promising to recycle the wind turbine blade to fabricate value-added high-performance composite. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluation of an Empirical Traction Equation for Forestry Tires

Treesearch

C.R. Vechinski; C.E. Johnson; R.L. Raper

1998-01-01

Variable load test data were used to evaluate the applicability of an existing forestry tire traction model for a new forestry tire and a worn tire of the same size with and without tire chains in a range of soil conditions. `The clay and sandy soi!s ranged in moisture content from 17 to 28%. Soil bulk density varied between 1.1 and 1.4g cm-3...

Modeling temperature effect on dynamic modulus of elasticity of red pine (Pinus resinosa) in frozen and non-frozen states

Treesearch

Shan Gao; Xiping Wang; Lihai Wang

2015-01-01

The response of dynamic and static modulus of elasticity (MOEdyn and MOEsta) of red pine small clear wood (25.4 × 25.4 × 407 mm3) within the temperature range -40 to 40°C has been investigated. The moisture content (MC) of the specimens ranged from 0 to 118%. The MOEdyn was...

Mechanisms of deterioration of intermediate moisture food systems

NASA Technical Reports Server (NTRS)

Labuza, T. P.

1972-01-01

A study of shelf stability in intermediate moisture foods was made. Major efforts were made to control lipid oxidation and nonenzymatic browning. In order to determine means of preventing these reactions, model systems were developed having the same water activity content relationship of intermediate moisture foods. Models were based on a cellulose-lipid and protein-lipid system with glycerol added as the humectant. Experiments with both systems indicate that lipid oxidation is promoted significantly in the intermediate moisture range. The effect appeared to be related to increased mobility of either reactants or catalysts, since when the amount of water in the system reached a level where capillary condensation occurred and thus free water was present, the rates of oxidation increased. With added glycerol, which is water soluble and thus increases the amount of mobile phase, the increase in oxidation rate occurs at a lower relative humidity. The rates of oxidation were maximized at 61% RH and decreased again at 75% RH probably due to dilution. No significant non-enzymatic browning occurred in the protein-lipid systems. Prevention of oxidation by the use of metal chelating agents was enhanced in the cellulose system, whereas, with protein present, the lipid soluble chain terminating antioxidants (such as BHA) worked equally as well. Preliminary studies of foods adjusted to the intermediate moisture range bear out the results of oxidation in model systems. It can be concluded that for most fat containing intermediate moisture foods, rancidity will be the reaction most limiting stability.

Studies and Application of Remote Sensing Retrieval Method of Soil Moisture Content in Land Parcel Units in Irrigation Area

NASA Astrophysics Data System (ADS)

Zhu, H.; Zhao, H. L.; Jiang, Y. Z.; Zang, W. B.

2018-05-01

Soil moisture is one of the important hydrological elements. Obtaining soil moisture accurately and effectively is of great significance for water resource management in irrigation area. During the process of soil moisture content retrieval with multiremote sensing data, multi- remote sensing data always brings multi-spatial scale problems which results in inconformity of soil moisture content retrieved by remote sensing in different spatial scale. In addition, agricultural water use management has suitable spatial scale of soil moisture information so as to satisfy the demands of dynamic management of water use and water demand in certain unit. We have proposed to use land parcel unit as the minimum unit to do soil moisture content research in agricultural water using area, according to soil characteristics, vegetation coverage characteristics in underlying layer, and hydrological characteristic into the basis of study unit division. We have proposed division method of land parcel units. Based on multi thermal infrared and near infrared remote sensing data, we calculate the ndvi and tvdi index and make a statistical model between the tvdi index and soil moisture of ground monitoring station. Then we move forward to study soil moisture remote sensing retrieval method on land parcel unit scale. And the method has been applied in Hetao irrigation area. Results show that compared with pixel scale the soil moisture content in land parcel unit scale has displayed stronger correlation with true value. Hence, remote sensing retrieval method of soil moisture content in land parcel unit scale has shown good applicability in Hetao irrigation area. We converted the research unit into the scale of land parcel unit. Using the land parcel units with unified crops and soil attributes as the research units more complies with the characteristics of agricultural water areas, avoids the problems such as decomposition of mixed pixels and excessive dependence on high-resolution data caused by the research units of pixels, and doesn't involve compromises in the spatial scale and simulating precision like the grid simulation. When the application needs are met, the production efficiency of products can also be improved at a certain degree.

Numerical and experimental studies on effects of moisture content on combustion characteristics of simulated municipal solid wastes in a fixed bed

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Rui, E-mail: Sunsr@hit.edu.cn; Ismail, Tamer M., E-mail: temoil@aucegypt.edu; Ren, Xiaohan

Highlights: • The effects of moisture content on the burning process of MSW are investigated. • A two-dimensional mathematical model was built to simulate the combustion process. • Temperature distributions, process rates, gas species were measured and simulated. • The The conversion ratio of C/CO and N/NO in MSW are inverse to moisture content. - Abstract: In order to reveal the features of the combustion process in the porous bed of a waste incinerator, a two-dimensional unsteady state model and experimental study were employed to investigate the combustion process in a fixed bed of municipal solid waste (MSW) on themore » combustion process in a fixed bed reactor. Conservation equations of the waste bed were implemented to describe the incineration process. The gas phase turbulence was modeled using the k–ε turbulent model and the particle phase was modeled using the kinetic theory of granular flow. The rate of moisture evaporation, devolatilization rate, and char burnout was calculated according to the waste property characters. The simulation results were then compared with experimental data for different moisture content of MSW, which shows that the incineration process of waste in the fixed bed is reasonably simulated. The simulation results of solid temperature, gas species and process rate in the bed are accordant with experimental data. Due to the high moisture content of fuel, moisture evaporation consumes a vast amount of heat, and the evaporation takes up most of the combustion time (about 2/3 of the whole combustion process). The whole bed combustion process reduces greatly as MSW moisture content increases. The experimental and simulation results provide direction for design and optimization of the fixed bed of MSW.« less

The effect of air temperature on the sappan wood extract drying

NASA Astrophysics Data System (ADS)

Djaeni, M.; Triyastuti, M. S.; Asiah, N.; Annisa, A. N.; Novita, D. A.

2015-12-01

The sappan wood extract contain natural colour called brazilin that can be used as a food colouring and antioxidant. The product is commonly found as a dry extract powder for consummer convenience. The spray dryer with air dehumidification can be an option to retain the colour and antioxidant agent. This paper discusses the effect of air temperature on sappan wood extract drying that was mixed with maltodextrin. As responses, the particle size, final moisture content, and extract solubility degradation were observed. In all cases, the process conducted in temperature ranging 90 - 110°C can retain the brazilin quality as seen in solubility and particle size. In addition, the sappan wood extract can be fully dried with moisture content below 2%. Moreover, with the increase of air temperature, the particle size of dry extract can be smaller.

Determination of the Ability to Measure Traces of Water in Dehydrated Residues of Waste Water by IR Diffuse Reflectance Spectra

NASA Astrophysics Data System (ADS)

Pratsenka, S. V.; Voropai, E. S.; Belkin, V. G.

2018-01-01

Rapid measurement of the moisture content of dehydrated residues is a critical problem, the solution of which will increase the efficiency of treatment facilities and optimize the process of applying flocculants. The ability to determine the moisture content of dehydrated residues using a meter operating on the IR reflectance principle was confirmed experimentally. The most suitable interference filters were selected based on an analysis of the obtained diffuse reflectance spectrum of the dehydrated residue in the range 1.0-2.7 μm. Calibration curves were constructed and compared for each filter set. A measuring filter with a transmittance maximum at 1.19 μm and a reference filter with a maximum at 1.3 μm gave the best agreement with the laboratory measurements.

Incorporation of bitumen and calcium silicate in cement and lime stabilized soil blocks

NASA Astrophysics Data System (ADS)

Kwan, W. H.; Cheah, C. B.; Ramli, M.; Al-Sakkaf, Y. K.

2017-04-01

Providing affordable housing is the most critical problem in many of the developing countries. Using earth materials in building construction is one of the feasible methods to address this issue and it can be a way towards sustainable construction as well. However, the published information on the stabilized soil blocks is limited. Therefore, the present study is conducted to examine the characterization of the soils and engineering properties of the stabilized soil blocks. Four types of stabilizer were used in the study, namely; cement, slaked lime, bitumen emulsion and calcium silicate. Cement and slaked lime were added at different percentages in the range of 5% to 15%, with interval of 2.5%. The percentage was determined based on weight of soil. Meanwhile, bitumen emulsion and calcium silicate were incorporated at various percentages together with 10% of cement. Dosage of bitumen emulsion is in the range of 2% to 10% at interval of 2% while calcium silicate was incorporated at 0.50%, 0.75%, 1.00%, 1.25%, 1.50% and 2.00%. Results show that cement is the most viable stabilizer for the soil block among all stabilizers in this study. The bulk density, optimum moisture content and compressive strengths were increased with the increasing cement content. The most suitable cement content was 10% added at moisture content of 12%. Lime, bitumen and calcium contents were recommended at 5.0%, 6.0% and 1.25%, respectively.

Dynamic analysis of temporal moisture profiles in heatset printing studied with near-infrared spectroscopy

NASA Astrophysics Data System (ADS)

Tåg, C.-M.; Toiviainen, M.; Juuti, M.; Gane, P. A. C.

2010-10-01

Dynamic analysis of the water transfer onto coated paper, and its permeation and absorption into the porous structure were studied online in a full-scale heatset web offset printing environment. The moisture content of the paper was investigated at five different positions during the printing process. Changes in the moisture content of the paper were studied as a function of the web temperature, printing speed and silicone application in the folding unit positioned after the hot air drying oven. Additionally, the influence of fountain solution composition on the pick-up by the paper was investigated. The water content of the fountain solution transferred to the paper from the printing units was observed as changes in near-infrared absorbance. A calibration data set enabled the subsequent quantification of the dynamic moisture content of the paper at the studied locations. An increase in the printing speed reduced the water transfer to the paper and an increase in web temperature resulted in a reduction in the moisture content. An increase in the dosage level of the water-silicone mixture was observed as a re-moistening effect of the paper. Differences in the drying strategy resulted in different moisture profiles depending on the type of fountain solution used. As a conclusion, the near-infrared signal provides an effective way to characterize the moisture dynamics online at different press units.

Effect of soil moisture on the sorption of trichloroethene vapor to vadose-zone soil at picatinny arsenal, New Jersey

USGS Publications Warehouse

Smith, J.A.; Chiou, C.T.; Kammer, J.A.; Kile, D.E.

1990-01-01

This report presents data on the sorption of trichloroethene (TCE) vapor to vadose-zone soil above a contaminated water-table aquifer at Picatinny Arsenal in Morris County, NJ. To assess the impact of moisture on TCE sorption, batch experiments on the sorption of TCE vapor by the field soil were carried out as a function of relative humidity. The TCE sorption decreases as soil moisture content increases from zero to saturation soil moisture content (the soil moisture content in equilibrium with 100% relative humidity). The moisture content of soil samples collected from the vadose zone was found to be greater than the saturation soil-moisture content, suggesting that adsorption of TCE by the mineral fraction of the vadose-zone soil should be minimal relative to the partition uptake by soil organic matter. Analyses of soil and soil-gas samples collected from the field indicate that the ratio of the concentration of TCE on the vadose-zone soil to its concentration in the soil gas is 1-3 orders of magnitude greater than the ratio predicted by using an assumption of equilibrium conditions. This apparent disequilibrium presumably results from the slow desorption of TCE from the organic matter of the vadose-zone soil relative to the dissipation of TCE vapor from the soil gas.

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... operate a dry rotary dryer, you must demonstrate that your dryer processes furnish with an inlet moisture.... You must record the inlet furnish moisture content (dry basis) and inlet dryer operating temperature... highest recorded 24-hour average inlet furnish moisture content and the highest recorded 24-hour average...

40 CFR 63.2263 - Initial compliance demonstration for a dry rotary dryer.

Code of Federal Regulations, 2011 CFR

2011-07-01

... operate a dry rotary dryer, you must demonstrate that your dryer processes furnish with an inlet moisture.... You must record the inlet furnish moisture content (dry basis) and inlet dryer operating temperature... highest recorded 24-hour average inlet furnish moisture content and the highest recorded 24-hour average...

Effect of black clay soil moisture on the electrochemical behavior of API X70 pipeline steel

NASA Astrophysics Data System (ADS)

Hendi, R.; Saifi, H.; Belmokre, K.; Ouadah, M.; Smili, B.; Talhi, B.

2018-03-01

The effect of moisture content variation (20–100 wt.%) on the electrochemical behavior of API X70 pipeline steel buried in the soil of Skikda (East of Algeria) was studied using electrochemical techniques, scanning electron microscopy (SEM), X ray diffraction analysis (XRD) and weight loss measurement. The electrochemical measurements showed that the corrosion current Icorr is directly proportional to the moisture content up to 50 wt.%, beyond this content, this value becomes almost constant. The result were confirmed by electrochemical impedance spectroscopy; the capacitance of the double layer formed on the surface is the highest at 50 wt.%. A single time constant was detected by plotting the Bode diagrams. The steel surface degradation has been appreciated using the scanning electron microscopy observations. A few pitting corrosion at 20 wt.% moisture, followed by more degradation at 50 wt.% have been revealed. However, when the moisture amount exceeded 50 wt.%, the surface became entirely covered by a corrosion product. XRD analysis revealed the dominance of FeOOH and Fe3O4 phases on steel surface for a moisture content of 50 wt.%.

Application of Response Surface Methodology to Study the Effects of Brisket Fat, Soy Protein Isolate, and Cornstarch on Nutritional and Textural Properties of Rabbit Sausages.

PubMed

Wambui, Joseph M; Karuri, Edward G; Wanyoike, Margaret M M

2017-01-01

The effects of brisket fat, soy protein isolate, and cornstarch on chemical and textural properties of rabbit sausages were studied using surface response methodology. Sausage samples were prepared using a five-level three-variable Central Composite Rotatable Design with 16 combinations, including two replicates of the center point, carried out in random order. The level of brisket fat (BF), soy protein isolate (SPI), and cornstarch (CS) in the sausage formulation ranged within 8.3-16.7%, 0.7-2.3%, and 1.3-4.7%, respectively. Increasing BF decreased moisture and ash contents but increased protein and fat contents of the sausages ( p < 0.05). Increasing SPI increased moisture content but decreased ash and carbohydrate contents of the sausages ( p < 0.05). Increasing CS increased carbohydrate content ( p < 0.05). Increasing BF increased hardness, adhesiveness, cohesiveness, and chewiness but decreased springiness ( p < 0.05). SPI addition increased springiness but decreased adhesiveness, cohesiveness, and chewiness ( p < 0.05). In conclusion, varying the levels of BF and SPI had a more significant effect on chemical and textural properties of rabbit sausages than CS.

Application of Response Surface Methodology to Study the Effects of Brisket Fat, Soy Protein Isolate, and Cornstarch on Nutritional and Textural Properties of Rabbit Sausages

PubMed Central

Karuri, Edward G.; Wanyoike, Margaret M. M.

2017-01-01

The effects of brisket fat, soy protein isolate, and cornstarch on chemical and textural properties of rabbit sausages were studied using surface response methodology. Sausage samples were prepared using a five-level three-variable Central Composite Rotatable Design with 16 combinations, including two replicates of the center point, carried out in random order. The level of brisket fat (BF), soy protein isolate (SPI), and cornstarch (CS) in the sausage formulation ranged within 8.3–16.7%, 0.7–2.3%, and 1.3–4.7%, respectively. Increasing BF decreased moisture and ash contents but increased protein and fat contents of the sausages (p < 0.05). Increasing SPI increased moisture content but decreased ash and carbohydrate contents of the sausages (p < 0.05). Increasing CS increased carbohydrate content (p < 0.05). Increasing BF increased hardness, adhesiveness, cohesiveness, and chewiness but decreased springiness (p < 0.05). SPI addition increased springiness but decreased adhesiveness, cohesiveness, and chewiness (p < 0.05). In conclusion, varying the levels of BF and SPI had a more significant effect on chemical and textural properties of rabbit sausages than CS. PMID:28706941

Influence of calcium and phosphorus, lactose, and salt-to-moisture ratio on Cheddar cheese quality: manufacture and composition.

PubMed

Upreti, P; Metzger, L E

2006-02-01

Eight Cheddar cheeses with 2 levels of calcium (Ca) and phosphorus (P), residual lactose, and salt-to-moisture ratio (S/M) were manufactured. All cheeses were made using a stirred-curd procedure and were replicated 3 times. Treatments with a high level of Ca and P were produced by setting the milk and drawing the whey at a higher pH (6.6 and 6.3, respectively) compared with the treatments with a low level of Ca and P (pH of 6.2 and 5.7, respectively). The lactose content in the cheeses was varied by adding lactose (2.5% by weight of milk) to the milk for high lactose cheeses, and washing the curd for low lactose cheeses. The difference in S/M was obtained by dividing the curds into halves, weighing each half, and salting at 3.5 and 2.25% of the weight of the curd for high and low S/M, respectively. All cheeses were salted at a pH of 5.4. Modifications in cheese-making protocols produced cheeses with desired differences in Ca and P, residual lactose, and S/M. Average Ca and P in the high Ca and P cheeses was 0.68 and 0.48%, respectively, vs. 0.53 and 0.41% for the low Ca and P cheeses. Average lactose content of the high lactose treatments at d 1 was 1.48% compared with 0.30% for the low lactose treatments. The S/M for the high and low S/M cheeses was 6.68 and 4.77%, respectively. Mean moisture, fat, and protein content of the cheeses ranged from 32.07 to 37.57%, 33.32 to 35.93%, and 24.46 to 26.40%, respectively. The moisture content differed among the treatments, whereas fat and protein content on dry basis was similar.

Antecedent moisture content and soil texture effects on infiltration and erosion

NASA Astrophysics Data System (ADS)

Mamedov, A. I.; Huang, C.; Levy, G. J.

2006-12-01

Water infiltration, seal formation, runoff and erosion depend on the soil's inherent properties and surface conditions. Most erosion models consider only soil inherent properties (mainly texture) in assessing infiltration and erosion without consideration of spatial and temporary variation in the surface condition, particularly the antecedent moisture content. We studied the interaction of two different surface conditions, i.e. antecedent moisture content (AMC) and aging (timing after wetting) on infiltration (IR), seal formation (runoff generation) and erosion in four soils varying from loam to clay. Soil samples were packed in erosion box and wetted with different amounts of water (0, 1, 2, 3, 4, 6, 8, or 16 mm) to obtain a wide moisture range (i.e., pF 0-6.2, or from air dry to full saturation). The boxes were put in plastic bags and allowed to age for 0.01, 1, 3, or 7 days. Then the soil in the erosion box exposed to 60 mm of rain. At no aging final IR of soils did not change significantly, but runoff volume (a measure for seal development) and soil loss increased with an increase in AMC mainly because of aggregate breakdown. For any given aging, the highest IR and smallest runoff volume and soil loss were obtained at the intermediate AMC levels (pF 2.4-4.2, between wilting point and field capacity). For instance, in the clay soil to which 3 mm of water (pF~2.7) was added, as aging increased from one to seven days, final IR increased from 5.3 to 7.9 mm h-1, while runoff and soil loss decreased from 34 mm to 22 mm, and from 630 to 360 g m2 respectively. At this AMC range, increasing aging time resulted in up to 40% increase in IR and decrease in runoff or soil loss. This tendency significantly more pronounced for clay soils because water-filled pores in the clay fabric were considered active in the stabilization process and the development of cohesive bonds between and within particles during the aging period. The results of this study are important for soil erosion modeling. In order to improve the prediction capabilities of erosion models, temporal and spatial variation of soil moisture content (AMC, wetting and aging) prior to erosive rainstorms should be considered and or incorporated. In addition, management practices could be adapted to diminish the severe soil moisture variation, where ever possible, (minimum till or no-till with known residue) to maintain the soil surface at a desired AMC level prior to expected rainstorms in order to decrease soil susceptibility to seal formation, runoff and soil loss.

Effects of storage environment on the moisture content and microbial growth of food waste.

PubMed

Chen, Ying-Chu; Hsu, Yi-Cheng; Wang, Chung-Ting

2018-05-15

Food waste (FW) has become a critical issue in sustainable development as the world's population has increased. Direct incineration of FW remains the primary treatment option. The moisture content of FW may affect the energy efficiency of incineration. In Taiwan, FW, which includes raw (r-FW) and post-consumer (p-FW) waste, is often stored in freezers before pretreatment. This study evaluated the effects of storage environment on the moisture content and microbial growth of FW. Storage at 263 K was associated with the largest reduction in moisture content in both r-FW and p-FW. At 263 K, the moisture content of r-FW and p-FW was lowest at 96 and 72 h, respectively. The E.coli and total bacteria counts were steady over 120 h when stored at 263 K. Storage at 253 K required the greatest electricity consumption, followed by 263 K and 258 K. Based on the reduction of moisture content and increase in energy efficiency, it is suggested that FW is placed in temporary storage at 263 K before (pre)treatment. The results of this study will help waste-to-energy plants, incinerators, and waste management enterprises to implement proper (pre)treatment of FW for sustainable waste management. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effectiveness of Hydraulic Parameterization Strategies for Simulating Moisture Dynamics in a Deep Semi-Arid Vadose Zone

NASA Astrophysics Data System (ADS)

Zhang, Y.; Schaap, M. G.

2012-12-01

Over the past fifteen years, the University of Arizona has carried out four controlled infiltration experiments in a 3600 m2, 15 meter deep vadose zone (Maricopa, Arizona) in which the evolution of moisture content (9 wells, 25 cm resolution), and matric potential (27 locations) was monitored and the subsurface stratigraphy, texture (1042 samples), and bulk density (251 samples) was characterized. In order to simulate the subsurface moisture dynamics it is necessary to define the 3D structure of the subsurface hydraulic characteristics (i.e. moisture retention and hydraulic functions). Several simple to complex strategies are possible ranging from stratigraphy based layering using hydraulic parameters derived from core samples to sophisticated numerical inversions based on 3D geostatistics and site-specific pedotransfer functions. A range of approaches will be evaluated on objective metrics that quantify how well the observed moisture dynamics are matched by simulations. We will evaluate the worth of auxiliary data such as observed matric potentials and quantity the number of texture samples needed to arrive at effective descriptions of subsurface structure. In addition, we will discuss more subjective metrics that evaluate the relative effort involved and estimate monetary cost of each method. While some of the results will only be valid for the studied site, some general conclusions will be possible about the effectiveness of particular methods for other semi-arid sites.

Vegetation water content of crops and woodlands for improving soil moisture retrievals from Coriolis WindSat

USDA-ARS?s Scientific Manuscript database

Estimation of vegetation water content (VWC) by shortwave infrared remote sensing improves soil moisture retrievals. The largest unknown for predicting VWC is stem water content; for woodlands, stem water content is expected to be proportional to stem height. Airborne imagery were acquired and photo...

Vegetation water content of crops and woodlands for improving soil moisture retrievals from Coriolis WindSat

USDA-ARS?s Scientific Manuscript database

Estimation of vegetation water content (VWC) by shortwave infrared remote sensing improves soil moisture retrievals. The largest unknown for predicting VWC is stem water content, which is assumed to be allometrically related to canopy water content. From forest science, stem volume is linearly relat...

Quality profile of litchi ( Litchi chinensis) cultivars from India and effect of radiation processing

NASA Astrophysics Data System (ADS)

Hajare, Sachin N.; Saxena, Sudhanshu; Kumar, Sanjeev; Wadhawan, Surbhi; More, Varsha; Mishra, B. B.; Narayan Parte, Madan; Gautam, Satyendra; Sharma, Arun

2010-09-01

Litchi ( Litchi chinensis) is a non-climacteric tropical fruit. The fruit has a short shelf-life making its marketing difficult. Physical, biochemical, microbiological, and organoleptic properties of two major commercially grown Indian cultivars of litchi, 'Shahi' and 'China' were studied. The effect of gamma radiation processing and low temperature storage on the above parameters was evaluated to standardize the optimal process parameters for shelf-life extension of litchi. Physical and biochemical parameters analyzed included weight, moisture, pH, titratable acidity, texture, color, total and reducing sugar, total soluble solids, vitamin C, and flavonoid content. Weight, moisture content, and pH in the fresh fruit ranged between 21-26 g, 74-77%, and 3.7-4.4, respectively, whereas, total and reducing sugar ranged 10-15, and 10-13 g%, respectively. In 'Shahi' vitamin C content was found to be around 17-19 mg%, whereas, in 'China' it was 22-28 mg%. Flavonoid content was in the range of 26-34 μg catechin equivalents/g of fresh fruit. Total surface and internal bacterial load was around 4 and 3 log cfu/g, respectively. Surface yeast-mold count (YMC) was ˜3 log cfu/g whereas internal YMC was ˜2 log cfu/g. Radiation treatment reduced microbial load in a dose dependent manner. Treatment at 0.5 kGy did not significantly affect the quality parameters of the fruit. Treated fruits retained the "good" organoleptic rating during storage. Thus, radiation treatment (0.5 kGy) in combination with low temperature (4 °C) storage achieved a shelf-life of 28 days for litchi fruit.

Ecology of the Pinewood Nematode in Southern Pine Chip Piles

Treesearch

L. David Dwinell

1986-01-01

The optimum temperature range for pinewood nematodes in southern pine chips was 35 to 40° C. Nematode populations declined at temperatures of -20°C. at temperatures above 45°C. and in anaerobic environments. Wood moisture content and presence of bluestain fungus also influenced nematode populations.

46 CFR 164.009-7 - Contents of application.

Code of Federal Regulations, 2010 CFR

2010-10-01

... trade name of the material. (b) The thickness or density, or both, of the material, or the range of thicknesses or densities, or both, of the material as manufactured. (c) The composition of the material. (d) The density and percentage of moisture and volatile matter of each component of the material. (e) The...

46 CFR 164.009-7 - Contents of application.

Code of Federal Regulations, 2011 CFR

2011-10-01

... trade name of the material. (b) The thickness or density, or both, of the material, or the range of thicknesses or densities, or both, of the material as manufactured. (c) The composition of the material. (d) The density and percentage of moisture and volatile matter of each component of the material. (e) The...

46 CFR 164.009-7 - Contents of application.

Code of Federal Regulations, 2014 CFR

2014-10-01

... trade name of the material. (b) The thickness or density, or both, of the material, or the range of thicknesses or densities, or both, of the material as manufactured. (c) The composition of the material. (d) The density and percentage of moisture and volatile matter of each component of the material. (e) The...

46 CFR 164.009-7 - Contents of application.

Code of Federal Regulations, 2013 CFR

2013-10-01

... trade name of the material. (b) The thickness or density, or both, of the material, or the range of thicknesses or densities, or both, of the material as manufactured. (c) The composition of the material. (d) The density and percentage of moisture and volatile matter of each component of the material. (e) The...

Quantification and spatial characterization of moisture and NaCl content of Iberian dry-cured ham slices using NIR hyperspectral imaging

USDA-ARS?s Scientific Manuscript database

Hyperspectral imaging technology is increasingly regarded as a powerful tool for the classification and spatial quantification of a wide range of agrofood product properties. Taking into account the difficulties involved in validating hyperspectral calibrations, the models constructed here proved mo...

Effects of selected process parameters in extrusion of yam flour (Dioscorea rotundata) on physicochemical properties of the extrudates.

PubMed

Sebio, L; Chang, Y K

2000-04-01

Raw yam (Dioscorea rotundata) flour was cooked and extruded in a Brabender single-screw laboratory scale extruder. Response surface methodology using an incomplete factorial design was applied with various combinations of barrel temperature [100, 125, 150 degrees C], feed moisture content [18, 22, 26%] and screw speed [100, 150, 200 rpm]. Initial viscosity at 30 degrees C, water solubility index, expansion and hardness were determined. The highest values of initial viscosity were at the highest barrel temperatures and the highest moisture contents. At high feed moisture content and high barrel temperatures the yam extrudate flour showed the greatest values of water solubility index. The physical properties of the extruded product showed that at high temperature the lower the moisture content the greater the expansion index. Hardness was influenced directly by moisture content and inversely by extrusion temperature. The extrusion of yam flour led to the production of snacks and pre-gelatinized flours of diverse properties. Also extruded yam flour can be successfully used in the preparation of 'futu' (pre-cooked compact dough), a yam-based food, popular in Western Africa.

Numerical analysis on centrifugal compressor with membrane type dryer

NASA Astrophysics Data System (ADS)

Razali, M. A.; Zulkafli, M. F.; Mat Isa, N.; Subari, Z.

2017-09-01

Moisture content is a common phenomenon in industrial processes especially in oil and gas industries. This contaminant has a lot of disadvantages which can lead to mechanical failure DEC (Deposition, Erosion & Corrosion) problems. To overcome DEC problem, this study proposed to design a centrifugal compressor with a membrane type dryer to reduce moisture content of a gas. The effectiveness of such design has been analyzed in this study using Computational Fluid Dynamics (CFD) approach. Numerical scheme based on multiphase flow technique is used in ANSYS Fluent software to evaluate the moisture content of the gas. Through this technique, two kind of centrifugal compressor, with and without membrane type dryer has been tested. The results show that the effects of pressure on dew point temperature of the gas change the composition of its moisture content, where high value lead more condensation to occur. However, with the injection of cool dry gas through membrane type dryer in the centrifugal compressor, the pressure and temperature of moisture content as well as mass fraction of H2O in centrifugal compressor show significant reduction.

Assessment of Evapotranspiration and Soil Moisture Content Across Different Scales of Observation.

PubMed

Verstraeten, Willem W; Veroustraete, Frank; Feyen, Jan

2008-01-09

The proper assessment of evapotranspiration and soil moisture content arefundamental in food security research, land management, pollution detection, nutrient flows,(wild-) fire detection, (desert) locust, carbon balance as well as hydrological modelling; etc.This paper takes an extensive, though not exhaustive sample of international scientificliterature to discuss different approaches to estimate land surface and ecosystem relatedevapotranspiration and soil moisture content. This review presents:(i) a summary of the generally accepted cohesion theory of plant water uptake andtransport including a shortlist of meteorological and plant factors influencing planttranspiration;(ii) a summary on evapotranspiration assessment at different scales of observation (sapflow,porometer, lysimeter, field and catchment water balance, Bowen ratio,scintillometer, eddy correlation, Penman-Monteith and related approaches);(iii) a summary on data assimilation schemes conceived to estimate evapotranspirationusing optical and thermal remote sensing; and(iv) for soil moisture content, a summary on soil moisture retrieval techniques atdifferent spatial and temporal scales is presented.Concluding remarks on the best available approaches to assess evapotranspiration and soilmoisture content with and emphasis on remote sensing data assimilation, are provided.

Glass transitions and physical aging of cassava starch - corn oil blends.

PubMed

Pérez, Adriana; Sandoval, Aleida J; Cova, Aura; Müller, Alejandro J

2014-05-25

Glass transition temperatures and physical aging of amorphous cassava starch and their blends with corn oil were assessed by differential scanning calorimetry (DSC). Two enthalpic relaxation endotherms, well separated in temperature values, were exhibited by neat amorphous cassava starch with 10.6% moisture content, evidencing two amorphous regions within the starch with different degrees of mobility. The phase segregation of these two amorphous regions was favored by added corn oil at low moisture contents during storage. The presence of amylose-lipid complexes in this matrix, may also affect the molecular dynamics of these two amorphous regions at low moisture contents. Increasing moisture content, leads to a homogeneous amorphous phase, with an aging process characterized by a single enthalpic relaxation peak. In all cases, after deleting the thermal history of the samples only one glass transition temperature was detected (during DSC second heating runs) indicating that a single homogeneous amorphous phase was attained after erasing the effects of physical aging. Trends of the enthalpic relaxation parameters were also different at the two moisture contents considered in this work. Copyright © 2014 Elsevier Ltd. All rights reserved.

Experimental study of nonlinear ultrasonic behavior of soil materials during the compaction.

PubMed

Chen, Jun; Wang, Hao; Yao, Yangping

2016-07-01

In this paper, the nonlinear ultrasonic behavior of unconsolidated granular medium - soil during the compaction is experimentally studied. The second harmonic generation technique is adopted to investigate the change of microstructural void in materials during the compaction process of loose soils. The nonlinear parameter is measured with the change of two important environmental factors i.e. moisture content and impact energy of compaction. It is found the nonlinear parameter of soil material presents a similar variation pattern with the void ratio of soil samples, corresponding to the increased moisture content and impact energy. A same optimum moisture content is found by observing the variation of nonlinear parameter and void ratio with respect to moisture content. The results indicate that the unconsolidated soil is manipulated by a strong material nonlinearity during the compaction procedure. The developed experimental technique based on the second harmonic generation could be a fast and convenient testing method for the determination of optimum moisture content of soil materials, which is very useful for the better compaction effect of filled embankment for civil infrastructures in-situ. Copyright © 2016 Elsevier B.V. All rights reserved.

Magnetic susceptibility and magnetic resonance measurements of the moisture content and hydration condition of a magnetic mixture material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsukada, K., E-mail: tsukada@cc.okayama-u.ac.jp; Kusaka, T.; Saari, M. M.

2014-05-07

We developed a magnetic measurement method to measure the moisture content and hydration condition of mortar as a magnetic mixture material. Mortar is a mixture of Portland cement, sand, and water, and these materials exhibit different magnetic properties. The magnetization–magnetic field curves of these components and of mortars with different moisture contents were measured, using a specially developed high-temperature-superconductor superconducting quantum interference device. Using the differences in magnetic characteristics, the moisture content of mortar was measured at the ferromagnetic saturation region over 250 mT. A correlation between magnetic susceptibility and moisture content was successfully established. After Portland cement and water aremore » mixed, hydration begins. At the early stage of the hydration/gel, magnetization strength increased over time. To investigate the magnetization change, we measured the distribution between bound and free water in the mortar in the early stage by magnetic resonance imaging (MRI). The MRI results suggest that the amount of free water in mortar correlates with the change in magnetic susceptibility.« less

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2011 CFR

2011-10-01

... migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...

An evaluation of fluid bed drying of aqueous granulations.

PubMed

Hlinak, A J; Saleki-Gerhardt, A

2000-01-01

The purpose of the work described was twofold: (a) to apply heat and mass balance approaches to evaluate the fluid bed drying cycle of an aqueous granulation, and (b) to determine the effect of the temperature and relative humidity of the drying air on the ability to meet a predetermined moisture content specification. Water content determinations were performed using Karl Fischer titration, and Computrac and Mark 1 moisture analyzers. The water vapor sorption isotherms were measured using a gravimetric moisture sorption apparatus with vacuum-drying capability. Temperature, relative humidity, and air flow were measured during the drying cycle of a production-scale fluid bed dryer. Heat and mass balance equations were used to calculate the evaporation rates. Evaporation rates calculated from heat and mass balance equations agreed well with the experimental data, whereas equilibrium moisture content values provided useful information for determination of the upper limit for inlet air humidity. Increasing the air flow rate and inlet temperature reduced the drying time through the effect on the primary driving force. As expected, additional drying of granules during the equilibration period did not show a significant impact on reducing the final moisture content of granules. Reducing the drying temperature resulted in measurement of higher equilibrium moisture content for the granules, which was in good agreement with the water vapor sorption data. Heat and mass balance equations can be used to successfully model the fluid bed drying cycle of aqueous granulations. The water vapor sorption characteristics of granules dictate the final moisture content at a given temperature and relative humidity.

Further experimentation on bubble generation during transformer overload

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oommen, T.V.

1992-03-01

This report covers additional work done during 1990 and 1991 on gas bubble generation under overload conditions. To improve visual bubble detection, a single disc coil was used. To further improve detection, a corona device was also used which signaled the onset of corona activity in the early stages of bubble formation. A total of fourteen model tests were conducted, half of which used the Inertaire system, and the remaining, a conservator (COPS). Moisture content of paper in the coil varied from 1.0% to 8.0%; gas (nitrogen) content varied from 1.0% to 8.8%. The results confirmed earlier observations that themore » mathematical bubble prediction model was not valid for high gas content model with relatively low moisture levels in the coil. An empirical relationship was formulated to accurately predict bubble evolution temperatures from known moisture and gas content values. For low moisture content models (below 2%), the simple Piper relationship was sufficient to predict bubble evolution temperatures, regardless of gas content. Moisture in the coil appears to be the key factor in bubble generation. Gas blanketed (Inertaire) systems do not appear to be prone to premature bubble generation from overloads as previously thought. The new bubble prediction model reveals that for a coil with 2% moisture, the bubble evolution temperature would be about 140{degrees}C. Since old transformers in service may have as much as 2% moisture in paper, the 140{degrees}C bubble evolution temperature may be taken as the lower limit of bubble evolution temperature under overload conditions for operating transformers. Drier insulation would raise the bubble evolution temperature.« less

Effect of different types of plastic packaging films on the moisture and aflatoxin contents of pistachio nuts during storage.

PubMed

Shakerardekani, Ahmad; Karim, Roselina

2013-04-01

Pistachio nut (Pistacia vera L.) is one of the popular tree nuts in the world. Proper selection of packaging materials is necessary to prevent absorption of moisture and aflatoxin formation which will influence the overall product quality and safety. This research is undertaken to study the effect of different type of flexible packaging films on the moisture and aflatoxin contents of whole pistachio nuts during storage at ambient temperature (22-28 °C) and relative humidity of 85-100%. Five types of plastic films tested were low density polyethylene (LDPE) which serves as the control, food-grade polyvinyl chloride (PVC), nylon (LDPE/PA), polyamide/polypropylene (PA/PP) and polyethylene terephthalate (PET). The moisture content and aflatoxin content of pistachio nuts were measured using oven drying method and HPLC, respectively. Sample were analysed at 0, 2, 4, 6, 8 and 10 months during the storage period. Results showed that there was an increase in moisture content with the increase in storage time of pistachio nuts. The increase in moisture content was associated with the aflatoxin level of pistachio nuts during storage time. All the packaging materials except LDPE delayed the moisture absorption and aflatoxin formation of the product. The most suitable packaging materials for maintaining the quality and safety of pistachio nuts is PET films followed by nylon, PA/PP and PVC. The shelf-life of pistachio can be extended from 2 months (Control) to 5 months when PET is used as the packaging material.

Specific yield - laboratory experiments showing the effect of time on column drainage

USGS Publications Warehouse

Prill, Robert C.; Johnson, A.I.; Morris, Donald Arthur

1965-01-01

The increasing use of ground water from many major aquifers in the United States has required a more thorough understanding of gravity drainage, or specific yield. This report describes one phase of specific yield research by the U.S. Geological Survey's Hydrologic Laboratory in cooperation with the California Department of Water Resources. An earlier phase of the research concentrated on the final distribution of moisture retained after drainage of saturated columns of porous media. This report presents the phase that concentrated on the distribution of moisture retained in similar columns after drainage for various periods of time. Five columns, about 4 cm in diameter by 170 cm long, were packed with homogenous sand of very fine, medium, and coarse sizes, and one column was packed with alternating layers of coarse and medium sand. The very fine materials were more uniform in size range than were the medium materials. As the saturated columns drained, tensiometers installed throughout the length recorded changes in moisture tension. The relation of tension to moisture content, determined for each of the materials, was then used to convert the tension readings to moisture content. Data were then available on the distribution of retained moisture for different periods of drainage from 1 to 148 hours. Data also are presented on the final distribution of moisture content by weight and volume and on the degree of saturation. The final zone of capillary saturation was approximately 12 cm for coarse sand, 13 cm for medium sand, and 52 cm for very fine sand. The data showed these zones were 92 to 100 percent saturated. Most of the outflow from the columns occurred in the earlier hours of drainage--90 percent in 1 hour for the coarse materials, 50 percent for the medium, and 60 percent for the very fine. Although the largest percentage of the specific yield was reached during the early hours of .drainage, this study amply demonstrates that a very long time would be required to reach drainage equilibrium. In the layered columns the middle (medium sand) layer functioned as a hanging water column accelerating the drainage of the overlying coarse-sand layer. After the middle layer started to drain, the moisture distribution as retained in all three layers showed trends similar to that obtained when the same materials were tested in homogenous columns.

Use of Ultrasonic Technology for Soil Moisture Measurement

NASA Technical Reports Server (NTRS)

Choi, J.; Metzl, R.; Aggarwal, M. D.; Belisle, W.; Coleman, T.

1997-01-01

In an effort to improve existing soil moisture measurement techniques or find new techniques using physics principles, a new technique is presented in this paper using ultrasonic techniques. It has been found that ultrasonic velocity changes as the moisture content changes. Preliminary values of velocities are 676.1 m/s in dry soil and 356.8 m/s in 100% moist soils. Intermediate values can be calibrated to give exact values for the moisture content in an unknown sample.

Implications of variable waste placement conditions for MSW landfills.

PubMed

Cox, Jason T; Yesiller, Nazli; Hanson, James L

2015-12-01

This investigation was conducted to evaluate the influence of waste placement practices on the engineering response of municipal solid waste (MSW) landfills. Waste placement conditions were varied by moisture addition to the wastes at the time of disposal. Tests were conducted at a California landfill in test plots (residential component of incoming wastes) and full-scale active face (all incoming wastes including residential, commercial, and self-delivered components). The short-term effects of moisture addition were assessed by investigating compaction characteristics and moisture distribution and the long-term effects by estimating settlement characteristics of the variably placed wastes. In addition, effects on engineering properties including hydraulic conductivity and shear strength, as well as economic aspects were investigated. The unit weight of the wastes increased with moisture addition to a maximum value and then decreased with further moisture addition. At the optimum moisture conditions, 68% more waste could be placed in the same landfill volume compared to the baseline conditions. Moisture addition raised the volumetric moisture content of the wastes to the range 33-42%, consistent with values at and above field capacity. Moisture transfer occurred between consecutive layers of compacted wastes and a moisture addition schedule of 2 days of as-received conditions and 1 day of moisture addition was recommended. Settlement of wastes was estimated to increase with moisture addition, with a 34% increase at optimum moisture compared to as-received conditions. Overall, moisture addition during compaction increased unit weight, the amount of incoming wastes disposed in a given landfill volume, biological activity potential, and predicted settlement. The combined effects have significant environmental and economic implications for landfill operations. Copyright © 2015 Elsevier Ltd. All rights reserved.

Resistant starch improvement of rice starches under a combination of acid and heat-moisture treatments.

PubMed

Hung, Pham Van; Vien, Ngo Lam; Lan Phi, Nguyen Thi

2016-01-15

The effects of a combination of acid and heat-moisture treatment on formation of resistant starch (RS) and characteristics of high-amylose, normal and waxy rice starches were investigated in this study. The degrees of polymerization of the rice starches treated with citric acid, lactic acid or acetic acid were significantly reduced as compared to the native starches. The RS contents of acid and heat-moisture treated rice starches were in a range of 30.1-39.0%, significantly higher than those of native rice starches (6.3-10.2%) and those of heat-moisture treated rice starches (18.5-23.9%). The acid and heat-moisture treatments reduced swelling power and viscosity, but increased solubility of the starches, while the crystalline structure did not change. Among the organic acids used, citric acid had the most impact on starch characteristics and RS formation, followed by lactic acid and acetic acid. The results are useful in production of RS for functional food application. Copyright © 2015 Elsevier Ltd. All rights reserved.

Finite Element Analysis of Simple Rectangular Microstrip Sensor for Determination Moisture Content of Hevea Rubber Latex

NASA Astrophysics Data System (ADS)

Yahaya, NZ; Ramli, MR; Razak, NNANA; Abbas, Z.

2018-04-01

The Finite Element Method, FEM has been successfully used to model a simple rectangular microstrip sensor to determine the moisture content of Hevea rubber latex. The FEM simulation of sensor and samples was implemented by using COMSOL Multiphysics software. The simulation includes the calculation of magnitude and phase of reflection coefficient and was compared to analytical method. The results show a good agreement in finding the magnitude and phase of reflection coefficient when compared with analytical results. Field distributions of both the unloaded sensor as well as the sensor loaded with different percentages of moisture content were visualized using FEM in conjunction with COMSOL software. The higher the amount of moisture content in the sample the more the electric loops were observed.

Evaluation of gravimetric ground truth soil moisture data collected for the agricultural soil moisture experiment, 1978 Colby, Kansas, aircraft mission

NASA Technical Reports Server (NTRS)

Arya, L. M.; Phinney, D. E. (Principal Investigator)

1980-01-01

Soil moisture data acquired to support the development of algorithms for estimating surface soil moisture from remotely sensed backscattering of microwaves from ground surfaces are presented. Aspects of field uniformity and variability of gravimetric soil moisture measurements are discussed. Moisture distribution patterns are illustrated by frequency distributions and contour plots. Standard deviations and coefficients of variation relative to degree of wetness and agronomic features of the fields are examined. Influence of sampling depth on observed moisture content an variability are indicated. For the various sets of measurements, soil moisture values that appear as outliers are flagged. The distribution and legal descriptions of the test fields are included along with examinations of soil types, agronomic features, and sampling plan. Bulk density data for experimental fields are appended, should analyses involving volumetric moisture content be of interest to the users of data in this report.

Effects of calcium oxide treatment at varying moisture concentrations on the chemical composition, in situ degradability, in vitro digestibility and gas production kinetics of anaerobically stored corn stover.

PubMed

Shi, H T; Cao, Z J; Wang, Y J; Li, S L; Yang, H J; Bi, Y L; Doane, P H

2016-08-01

The objective of this study was to determine the optimum conditions for calcium oxide (CaO) treatment of anaerobically stored corn stover by in situ and in vitro methods. Four ruminally cannulated, non-lactating, non-pregnant Holstein cows were used to determine the in situ effective degradabilities of dry matter (ISDMD), organic matter (ISOMD), neutral detergent fibre (ISNDFD), in vitro organic matter disappearance (IVOMD) and gas production in 72 h (GP72h ) of corn stover. A completely randomized design involving a 3 × 3 factorial arrangement was adopted. Ground corn stover was treated with different levels of CaO (3%, 5% and 7% of dry stover) at varying moisture contents (40%, 50% and 60%) and stored under anaerobic conditions for 15 days before analysis. Compared with untreated corn stover, the CaO-treated stover had increased ash and calcium (Ca) contents but decreased aNDF and OM contents. The moisture content, CaO level and their interaction affected (p < 0.01) the content of aNDF, ash and OM, and the ratio of aNDF/OM. The greatest ISDMD, ISOMD and ISNDFD were observed when stover was treated with 7% CaO and 60% moisture, while no differences (p > 0.01) in these in situ degradability parameters were observed between the stover treated with 5% CaO at 60% moisture content and those treated with 7% CaO at 60% moisture content. Corn stover treated with 5% CaO at 50% moisture had the maximum IVOMD and GP72 h among the treatments, and there was no difference (p > 0.01) between 50% and 60% moisture. Results from this study suggested that 5% CaO applied at 60% moisture could be an effective and economical treatment combination. Journal of Animal Physiology and Animal Nutrition © 2015 Blackwell Verlag GmbH.

Case study of landfill leachate recirculation using small-diameter vertical wells.

PubMed

Jain, Pradeep; Ko, Jae Hac; Kumar, Dinesh; Powell, Jon; Kim, Hwidong; Maldonado, Lizmarie; Townsend, Timothy; Reinhart, Debra R

2014-11-01

A case study of landfill liquids addition using small diameter (5 cm) vertical wells is reported. More than 25,000 m(3) of leachate was added via 134 vertical wells installed 3 m, 12 m, and 18 m deep over five years in a landfill in Florida, US. Liquids addition performance (flow rate per unit screen length per unit liquid head) ranged from 5.6×10(-8) to 3.6×10(-6) m(3) s(-1) per m screen length per m liquid head. The estimated radial hydraulic conductivity ranged from 3.5×10(-6) to 4.2×10(-4) m s(-1). The extent of lateral moisture movement ranged from 8 to 10 m based on the responses of moisture sensors installed around vertical well clusters, and surface seeps were found to limit the achievable liquids addition rates, despite the use of concrete collars under a pressurized liquids addition scenario. The average moisture content before (51 samples) and after (272 samples) the recirculation experiments were 23% (wet weight basis) and 45% (wet weight basis), respectively, and biochemical methane potential measurements of excavated waste indicated significant (p<0.025) decomposition. Copyright © 2014 Elsevier Ltd. All rights reserved.

A Review on Biomass Torrefaction Process and Product Properties

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jaya Shankar Tumuluru; Shahab Sokhansanj; Christopher T. Wright

2011-08-01

Biomass Torrefaction is gaining attention as an important preprocessing step to improve the quality of biomass in terms of physical properties and chemical composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of approximately 300 C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200-280 C. Thus, the process can be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefactionmore » process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, which produces a final product that will have a lower mass but a higher heating value. The present review work looks into (a) torrefaction process and different products produced during the process and (b) solid torrefied material properties which include: (i) physical properties like moisture content, density, grindability, particle size distribution and particle surface area and pelletability; (ii) chemical properties like proximate and ultimate composition; and (iii) storage properties like off-gassing and spontaneous combustion.« less

Evaluation of standard methods for collecting and processing fuel moisture samples

Treesearch

Sally M. Haase; José Sánchez; David R. Weise

2016-01-01

A variety of techniques for collecting and processing samples to determine moisture content of wildland fuels in support of fire management activities were evaluated. The effects of using a chainsaw or handsaw to collect samples of largediameter wood, containers for storing and transporting collected samples, and quick-response ovens for estimating moisture content...

CAPACITANCE SENSING OF MOISTURE CONTENT IN BIO-FUEL MATERIALS: A RAPID AND NONDESTRUCTIVE METHOD FOR WOOD CHIPS

USDA-ARS?s Scientific Manuscript database

Moisture content of wood chips is an important factor to be known in their utilization as biomass material. Several moisture measuring instruments are available in the market, but for most of these instruments, some sort of sample preparation is needed that involves sizing, grinding and weighing. T...

A Rapid Soils Analysis Kit

DTIC Science & Technology

2008-03-01

behavior of moisture content-dry density Proctor curves......................................... 16 Figure 8. Moisture- density data scatter for an... density . Built-in higher order regression equations allow the user to visua- lize complete curves for Proctor density , as-built California Bearing Ratio...requirements involving soil are optimum moisture content (OMC) and maximum dry density (MDD) as determined from a laboratory compaction or Proctor test

Moisture distributions in western hemlock lumber from trees harvested near Sitka, Alaska.

Treesearch

David L. Nicholls; Allen M. Brackley; Travis. Allen

2003-01-01

Western hemlock (Tsuga heterophylla) can be characterized by localized regions of high-moisture-content wood, often referred to as wet pockets, and uneven drying conditions may occur when lumber of higher and lower moisture content is mixed together in a dry kiln. The primary objective of this preliminary study was to characterize the frequency and...

Predicting duff and woody fuel consumed by prescribed fire in the Northern Rocky Mountains

Treesearch

James K. Brown; Michael A. Marsden; Kevin C. Ryan; Elizabeth D. Reinhardt

1985-01-01

Relationships for predicting duff reduction, mineral soil exposure, and consumption of downed woody fuel were determined to assist in planning prescribed fires. Independent variables included lower and entire duff moisture contents, loadings of downed woody fuels, duff depth, National Fire-Danger Rating System 1,000-hour moisture content, and Canadian Duff Moisture...

Calculating moisture content for 1000-hour timelag fuels in western Washington and western Oregon.

Treesearch

Roger D. Ottmar; David V. Sandberg

1985-01-01

A predictive model is presented to calculate moisture content of 1000-hour timelag fuels in Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) and western hemlock (Tsuga heterophylla (Raf.) Sarg.) logging slash in western Washington and western Oregon. The model is a modification of the 1000-hour fuel moisture model of the...

Parameters influencing the regeneration of a green roof's retention capacity via evapotranspiration

NASA Astrophysics Data System (ADS)

Poë, Simon; Stovin, Virginia; Berretta, Christian

2015-04-01

The extent to which the finite hydrological capacity of a green roof is available for retention of a storm event largely determines the scale of its contribution as a Sustainable Drainage System (SuDS). Evapotranspiration (ET) regenerates the retention capacity at a rate that is variably influenced by climate, vegetation treatment, soil and residual moisture content. Experimental studies have been undertaken to monitor the drying cycle behaviour of 9 different extensive green roof configurations with 80 mm substrate depth. A climate-controlled chamber at the University of Sheffield replicated typical UK spring and summer diurnal cycles. The mass of each microcosm, initially at field capacity, was continuously recorded, with changes inferred to be moisture loss/gain (or ET/dew). The ranges of cumulative ET following a 28 day dry weather period (ADWP) were 0.6-1.0 mm/day in spring and 0.7-1.25 mm/day in summer. These ranges reflect the influence of configuration on ET. Cumulative ET was highest from substrates with the greatest storage capacity. Significant differences in ET existed between vegetated and non-vegetated configurations. Initially, seasonal mean ET was affected by climate. Losses were 2.0 mm/day in spring and 3.4 mm/day in summer. However, moisture availability constrained ET, which fell to 1.4 mm/day then 1.0 mm/day (with an ADWP of 7 and 14 days) in spring; compared to 1.0 mm/day and 0.5 mm/day in summer. A modelling approach, which factors Potential Evapotranspiration (PET) according to stored moisture content, predicts daily ET with very good accuracy (PBIAS = 2.0% [spring]; -0.8% [summer]).

Synergy of the SimSphere land surface process model with ASTER imagery for the retrieval of spatially distributed estimates of surface turbulent heat fluxes and soil moisture content

NASA Astrophysics Data System (ADS)

Petropoulos, George; Wooster, Martin J.; Carlson, Toby N.; Drake, Nick

2010-05-01

Accurate information on spatially explicit distributed estimates of key land-atmosphere fluxes and related land surface parameters is of key importance in a range of disciplines including hydrology, meteorology, agriculture and ecology. Estimation of those parameters from remote sensing frequently employs the integration of such data with mathematical representations of the transfers of energy, mass and radiation between soil, vegetation and atmosphere continuum, known as Soil Vegetation Atmosphere Transfer (SVAT) models. The ability of one such inversion modelling scheme to resolve for key surface energy fluxes and of soil surface moisture content is examined here using data from a multispectral high spatial resolution imaging instrument, the Advanced Spaceborne Thermal Emission and Reflection Scanning Radiometer (ASTER) and SimSphere one-dimensional SVAT model. Accuracy of the investigated methodology, so-called as the "triangle" method, is verified using validated ground observations obtained from selected days collected from nine CARBOEUROPE IP sites representing a variety of climatic, topographic and environmental conditions. Subsequently, a new framework is suggested for the retrieval of two additional parameters by the investigated method, namely the Evaporative (EF) and the Non-Evaporative (NEF) Fractions. Results indicated a close agreement between the inverted surface fluxes and surface moisture availability maps as well as of the EF and NEF parameters with the observations both spatially and temporally with accuracies comparable to those obtained in similar experiments with high spatial resolution data. Inspection of the inverted surface fluxes maps regionally, showed an explainable distribution in the range of the inverted parameters in relation with the surface heterogeneity. Overall performance of the "triangle" inversion methodology was found to be affected predominantly by the SVAT model "correct" initialisation representative of the test site environment, most importantly the atmospheric conditions required in the SVAT model initial conditions. This study represents the first comprehensive evaluation of the performance of this particular methodological implementation at a European setting using the SimSphere SVAT with the ASTER data. The present work is also very timely in that, a variation of this specific inversion methodology has been proposed for the operational retrieval of the soil surface moisture content by National Polar-orbiting Operational Environmental Satellite System (NPOESS), in a series of satellite platforms that are due to be launched in the next 12 years starting from 2012. KEYWORDS: micrometeorology, surface heat fluxes, soil moisture content, ASTER, triangle method, SimSphere, CarboEurope IP

21 CFR 133.167 - Pasteurized blended cheese.

Code of Federal Regulations, 2012 CFR

2012-04-01

... or more cheeses containing cream cheese or neufchatel cheese, the moisture content is not more than the arithmetical average of the maximum moisture contents prescribed by the definitions and standards...

A study on the applicability of in-line measurements in the monitoring of the pellet coating process.

PubMed

Hudovornik, Grega; Korasa, Klemen; Vrečer, Franc

2015-07-30

Special populations including paediatric and elderly patients often need advanced approaches in treatment, such as one-a-day dosing, which is achieved with modified release formulations or alternative routes of applications such as nasogastric route. Pellets are a dosage form that is frequently used in such formulations. The aim of the present work was to study the applicability of two in-line techniques, namely, Near Infrared Spectroscopy (NIR) and Spatial Filtering Technique (SFT) in the pellet coating process. The first objective of our work was to develop a prediction model for moisture content determination with the in-line NIR and to test its robustness in terms of sensitivity to changes in composition of the pellets and performance in wide range of moisture content. Secondly, the in-line SFT measurement was correlated with different off-line particle size methods. The third objective was to evaluate the ability of both in-line techniques for the detection of undesired deviations during the process, such as pellet attrition and agglomeration. Finally, the ability to predict coating thickness with the in-line NIR probe was evaluated. Results suggested that NIR prediction model for moisture content was less robust outside the calibration range and was also sensitive to changes in composition of the film coating. Nevertheless, satisfactory prediction was achieved in the case when coating composition was partially altered and adequate calibration range was used. The SFT probe results were in good correlation with off-line particle size measurement methods and proved to be an effective tool for coating thickness determination during the coating, however, the probe failed to accurately show the actual amount of the agglomerates formed during the process. In experiment when pellet attrition was initiated, both probes successfully detected abrasion of the pellet surface in real time. Furthermore, a predictive NIR model for coating thickness was made and showed a good potential to measure coating thickness in-line, suggesting that the NIR probe can be used as a single tool to monitor water content, coating thickness, and deviations in the coating process. Copyright © 2015 Elsevier B.V. All rights reserved.

Investigation of Analytical Techniques for the Rapid Determination of the Moisture Content of NOL 130 Primer Mix and Lead Azide

DTIC Science & Technology

1986-05-01

the presence of NOL 130 6 Determination of moisture content of dextrinated lead azide 14 containing known amounts of water, by the Karl Fisher method...maLhiod, extraction mode 8 Determinatiov) of moisture content of special purpose and 16 dextrinated lead atide, containing known amounts of water by the...water in special purpose and dextrinated lead azides were determined by the method described in the experimen- tal section of this report, data shown

On-irrigator pasture soil moisture sensor

NASA Astrophysics Data System (ADS)

Eng-Choon Tan, Adrian; Richards, Sean; Platt, Ian; Woodhead, Ian

2017-02-01

In this paper, we presented the development of a proximal soil moisture sensor that measured the soil moisture content of dairy pasture directly from the boom of an irrigator. The proposed sensor was capable of soil moisture measurements at an accuracy of  ±5% volumetric moisture content, and at meter scale ground area resolutions. The sensor adopted techniques from the ultra-wideband radar to enable measurements of ground reflection at resolutions that are smaller than the antenna beamwidth of the sensor. An experimental prototype was developed for field measurements. Extensive field measurements using the developed prototype were conducted on grass pasture at different ground conditions to validate the accuracy of the sensor in performing soil moisture measurements.

The measurement of the dielectric constant of concrete pipes and clay pipes

NASA Astrophysics Data System (ADS)

McGraw, David

To optimize the effectiveness of the rehabilitation of underground utilities, taking in consideration limitation of available resources, there is a need for a cost effective and efficient sensing systems capable of providing effective, in real time and in situ, measurement of infrastructural characteristics. To carry out accurate non-destructive condition assessment of buried and above ground infrastructure such as sewers, bridges, pavements and dams, an advanced ultra-wideband (UWB) based radar was developed at Trenchless Technology Centre (TTC) and Centre for Applied Physics Studies (CAPS) at Louisiana Tech University (LTU). One of the major issues in designing the FCC compliant UWB radar was the contribution of the pipe wall, presence of complex soil types and moderate-to-high moisture levels on penetration depth of the electromagnetic (EM) energy. The electrical properties of the materials involved in designing the UWB radar exhibit a significant variation as a result of the moisture content, mineral content, bulk density, temperature and frequency of the electromagnetic signal propagating through it. Since no measurements of frequency dependence of the dielectric permittivity and conductivities of the pipe wall material in the FCC approved frequency range exist, in this thesis, the dielectric constant of concrete and clay pipes are measured over a microwave frequency range from 1 Ghz to 10 Ghz including the effects of moisture and chloride content. A high performance software package called MU-EPSLN(TM) was used for the calculations. Data reduction routines to calculate the complex permeability and permittivity of materials as well as other parameters are also provided. The results obtained in this work will be used to improve the accuracy of the numerical simulations and the performances of the UWB radar system.

Characterizing a Brazilian sanitary landfill using geophysical seismic techniques.

PubMed

Abreu, A E S; Gandolfo, O C B; Vilar, O M

2016-07-01

Two different geophysical techniques, namely crosshole and multichannel analysis of surface waves - MASW, were applied to investigate the mechanical response of Municipal Solid Waste buried under humid, subtropical climate. Direct investigations revealed that the buried waste was composed mainly of soil-like material (51%) and plastics (31%) with moisture content average values of 43% near the surface and 53% after around 11m depth. Unit weight varied between 9kN/m(3) and 15kN/m(3). Seismic investigation of the landfill yielded shear wave velocities (VS) estimated from the crosshole tests ranging from 92 to 214m/s, while compression wave velocities (VP) ranged from 197 to 451m/s. Both velocities were influenced by vertical confining stress and thus tended to increase with depth. VS calculated from MASW tests were lower than the ones calculated from the crosshole tests, probably due to the different frequencies used in the tests. The results of both methods tended to configure a lower bound to the values reported in the technical literature in general, as expected for low compaction waste with small amounts of cover soil. Although VS did not show abrupt changes with depth, VP profile distribution combined with direct investigations results, such as temperature, in-place unit weight and moisture content, suggest that the waste body could be divided into two strata. The lower one is poorly drained and shows higher moisture content, as a consequence of the operational techniques used in the first years, while the upper stratum is probably related to a better drained waste stratum, resulting from the improvement of operational standards and increase in drainage facilities throughout the years. Copyright © 2016 Elsevier Ltd. All rights reserved.

Monitoring and optimizing the co-composting of dewatered sludge: a mixture experimental design approach.

PubMed

Komilis, Dimitrios; Evangelou, Alexandros; Voudrias, Evangelos

2011-09-01

The management of dewatered wastewater sludge is a major issue worldwide. Sludge disposal to landfills is not sustainable and thus alternative treatment techniques are being sought. The objective of this work was to determine optimal mixing ratios of dewatered sludge with other organic amendments in order to maximize the degradability of the mixtures during composting. This objective was achieved using mixture experimental design principles. An additional objective was to study the impact of the initial C/N ratio and moisture contents on the co-composting process of dewatered sludge. The composting process was monitored through measurements of O(2) uptake rates, CO(2) evolution, temperature profile and solids reduction. Eight (8) runs were performed in 100 L insulated air-tight bioreactors under a dynamic air flow regime. The initial mixtures were prepared using dewatered wastewater sludge, mixed paper wastes, food wastes, tree branches and sawdust at various initial C/N ratios and moisture contents. According to empirical modeling, mixtures of sludge and food waste mixtures at 1:1 ratio (ww, wet weight) maximize degradability. Structural amendments should be maintained below 30% to reach thermophilic temperatures. The initial C/N ratio and initial moisture content of the mixture were not found to influence the decomposition process. The bio C/bio N ratio started from around 10, for all runs, decreased during the middle of the process and increased to up to 20 at the end of the process. The solid carbon reduction of the mixtures without the branches ranged from 28% to 62%, whilst solid N reductions ranged from 30% to 63%. Respiratory quotients had a decreasing trend throughout the composting process. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effect of pH, temperature and moisture content during composting of rice straw burning at different temperature with food waste and effective microorganisms

NASA Astrophysics Data System (ADS)

Azura Zakarya, Irnis; Baya Khalib, Siti Noor; Ramzi, Norhasykin Mohd

2018-03-01

Rice straw is considered as one of the most important agricultural residues and represented as one of the major by-products from rice production process. Normally, rice straw that produced after harvesting season been directly burned on-farm. Conversion of rice straw into value added compost will improve the productivity of plant, reduction of pollution towards environment and reduction of local pollution due to open burning activity. The objective of this study was to evaluate the performance of composting rice straw ash (RSA) with food waste (FW) and effective microorganisms (EM) in term of the compost quality (pH, temperature, moisture content). RSA was prepared by burning the raw rice straw at three different temperature of 300°C, 400°C and 500°C for one hour. EM used during the composting process was prepared by mixing of brown sugar, `tempe' and water that can be used after one week of fermentation process. There are four treatments of RSA-compost; RSA (300°C), RSA (400°C), RSA (500°C) and control (raw rice straw) with the same amount of compost medium; 1kg black soil, 0.5kg RSA, 3L EM and 1kg FW. The composting process happens for 30 days. During the composting process, all the parameters of RSA-compost obtained in a range like; pH value 8-10, temperature 20-50°C and moisture content 40-60%. The result showed that all compost quality of rice straw ash compost obtained in an acceptable range for final compost to establish.

Antioxidant potential and quality characteristics of vegetable-enriched corn-based extruded snacks.

PubMed

Bisharat, G I; Lazou, A E; Panagiotou, N M; Krokida, M K; Maroulis, Z B

2015-07-01

Phenolic content, antioxidant activity and sensory characteristics of vegetable-enriched extrudates were investigated as a result of extrusion conditions, including extrusion temperature (140-180 °C), screw rotation speed (150-250 rpm) and feed moisture content (14-19 % w.b.). Broccoli flour and olive paste was used in mixtures with corn flour at a ratio of 4 to 10 % (broccoli/corn) and 4 to 8 % (olive paste/corn). A simple power model was developed for the prediction of phenolic content and antioxidant activity of extrudates by extrusion conditions and feed composition. Phenolic content and antioxidant activity of broccoli enriched extrudates increased with extrusion temperature and broccoli addition and decreased with feed moisture content. The antioxidant activity of olive paste extrudates increased with material ratio and decreased with feed moisture content and screw rotation. Sensory porosity, homogenous structure, crispness, cohesiveness and melting decreased with feed moisture content, while the latter increased the mealy flavor and hardness of extrudates. Acceptable snacks containing broccoli flour or olive paste can be produced by selecting the appropriate process conditions.

Assessment of Multi-frequency Electromagnetic Induction for Determining Soil Moisture Patterns at the Hillslope Scale

NASA Astrophysics Data System (ADS)

Tromp-van Meerveld, I.; McDonnell, J.

2009-05-01

We present an assessment of electromagnetic induction (EM) as a potential rapid and non-invasive method to map soil moisture patterns at the Panola (GA, USA) hillslope. We address the following questions regarding the applicability of EM measurements for hillslope hydrological investigations: (1) Can EM be used for soil moisture measurements in areas with shallow soils?; (2) Can EM represent the temporal and spatial patterns of soil moisture throughout the year?; and (3) can multiple frequencies be used to extract additional information content from the EM approach and explain the depth profile of soil moisture? We found that the apparent conductivity measured with the multi-frequency GEM-300 was linearly related to soil moisture measured with an Aqua-pro capacitance sensor below a threshold conductivity and represented the temporal patterns in soil moisture well. During spring rainfall events that wetted only the surface soil layers the apparent conductivity measurements explained the soil moisture dynamics at depth better than the surface soil moisture dynamics. All four EM frequencies (7290, 9090, 11250, and 14010 Hz) were highly correlated and linearly related to each other and could be used to predict soil moisture. This limited our ability to use the four different EM frequencies to obtain a soil moisture profile with depth. The apparent conductivity patterns represented the observed spatial soil moisture patterns well when the individually fitted relationships between measured soil moisture and apparent conductivity were used for each measurement point. However, when the same (master) relationship was used for all measurement locations, the soil moisture patterns were smoothed and did not resemble the observed soil moisture patterns very well. In addition, the range in calculated soil moisture values was reduced compared to observed soil moisture. Part of the smoothing was likely due to the much larger measurement area of the GEM-300 compared to the Aqua-pro soil moisture measurements.

Method to Produce Durable Pellets at Lower Energy Consumption Using High Moisture Corn Stover and a Corn Starch Binder in a Flat Die Pellet Mill

PubMed Central

Tumuluru, Jaya Shankar; Conner, Craig C.; Hoover, Amber N.

2016-01-01

A major challenge in the production of pellets is the high cost associated with drying biomass from 30 to 10% (w.b.) moisture content. At Idaho National Laboratory, a high-moisture pelleting process was developed to reduce the drying cost. In this process the biomass pellets are produced at higher feedstock moisture contents than conventional methods, and the high moisture pellets produced are further dried in energy efficient dryers. This process helps to reduce the feedstock moisture content by about 5-10% during pelleting, which is mainly due to frictional heat developed in the die. The objective of this research was to explore how binder addition influences the pellet quality and energy consumption of the high-moisture pelleting process in a flat die pellet mill. In the present study, raw corn stover was pelleted at moistures of 33, 36, and 39% (w.b.) by addition of 0, 2, and 4% pure corn starch. The partially dried pellets produced were further dried in a laboratory oven at 70 °C for 3-4 hr to lower the pellet moisture to less than 9% (w.b.). The high moisture and dried pellets were evaluated for their physical properties, such as bulk density and durability. The results indicated that increasing the binder percentage to 4% improved pellet durability and reduced the specific energy consumption by 20-40% compared to pellets with no binder. At higher binder addition (4%), the reduction in feedstock moisture during pelleting was <4%, whereas the reduction was about 7-8% without the binder. With 4% binder and 33% (w.b.) feedstock moisture content, the bulk density and durability values observed of the dried pellets were >510 kg/m3 and >98%, respectively, and the percent fine particles generated was reduced to <3%. PMID:27340875

Method to Produce Durable Pellets at Lower Energy Consumption Using High Moisture Corn Stover and a Corn Starch Binder in a Flat Die Pellet Mill.

PubMed

Tumuluru, Jaya Shankar; Conner, Craig C; Hoover, Amber N

2016-06-15

A major challenge in the production of pellets is the high cost associated with drying biomass from 30 to 10% (w.b.) moisture content. At Idaho National Laboratory, a high-moisture pelleting process was developed to reduce the drying cost. In this process the biomass pellets are produced at higher feedstock moisture contents than conventional methods, and the high moisture pellets produced are further dried in energy efficient dryers. This process helps to reduce the feedstock moisture content by about 5-10% during pelleting, which is mainly due to frictional heat developed in the die. The objective of this research was to explore how binder addition influences the pellet quality and energy consumption of the high-moisture pelleting process in a flat die pellet mill. In the present study, raw corn stover was pelleted at moistures of 33, 36, and 39% (w.b.) by addition of 0, 2, and 4% pure corn starch. The partially dried pellets produced were further dried in a laboratory oven at 70 °C for 3-4 hr to lower the pellet moisture to less than 9% (w.b.). The high moisture and dried pellets were evaluated for their physical properties, such as bulk density and durability. The results indicated that increasing the binder percentage to 4% improved pellet durability and reduced the specific energy consumption by 20-40% compared to pellets with no binder. At higher binder addition (4%), the reduction in feedstock moisture during pelleting was <4%, whereas the reduction was about 7-8% without the binder. With 4% binder and 33% (w.b.) feedstock moisture content, the bulk density and durability values observed of the dried pellets were >510 kg/m(3) and >98%, respectively, and the percent fine particles generated was reduced to <3%.

Selected micrometeorological and soil-moisture data at Amargosa Desert Research Site, an arid site near Beatty, Nye County, Nevada, 1998-2000

USGS Publications Warehouse

Johnson, Michael J.; Mayers, Charles J.; Andraski, Brian J.

2002-01-01

Selected micrometeorological and soil-moisture data were collected at the Amargosa Desert Research Site adjacent to a low-level radioactive waste and hazardous chemical waste facility near Beatty, Nev., 1998-2000. Data were collected in support of ongoing research studies to improve the understanding of hydrologic and contaminant-transport processes in arid environments. Micrometeorological data include precipitation, air temperature, solar radiation, net radiation, relative humidity, ambient vapor pressure, wind speed and direction, barometric pressure, soil temperature, and soil-heat flux. All micrometeorological data were collected using a 10-second sampling interval by data loggers that output daily mean, maximum, and minimum values, and hourly mean values. For precipitation, data output consisted of daily, hourly, and 5-minute totals. Soil-moisture data included periodic measurements of soil-water content at nine neutron-probe access tubes with measurable depths ranging from 5.25 to 29.75 meters. The computer data files included in this report contain the complete micrometeorological and soil-moisture data sets. The computer data consists of seven files with about 14 megabytes of information. The seven files are in tabular format: (1) one file lists daily mean, maximum, and minimum micrometeorological data and daily total precipitation; (2) three files list hourly mean micrometeorological data and hourly precipitation for each year (1998-2000); (3) one file lists 5-minute precipitation data; (4) one file lists mean soil-water content by date and depth at four experimental sites; and (5) one file lists soil-water content by date and depth for each neutron-probe access tube. This report highlights selected data contained in the computer data files using figures, tables, and brief discussions. Instrumentation used for data collection also is described. Water-content profiles are shown to demonstrate variability of water content with depth. Time-series data are plotted to illustrate temporal variations in micrometeorological and soil-water content data. Substantial precipitation at the end of an El Ni?o cycle in early 1998 resulted in measurable water penetration to a depth of 1.25 meters at one of the four experimental soil-monitoring sites.

Selected micrometeorological, soil-moisture, and evapotranspiration data at Amargosa Desert Research Site in Nye County near Beatty, Nevada, 2001-05

USGS Publications Warehouse

Johnson, Michael J.; Mayers, C. Justin; Garcia, C. Amanda; Andraski, Brian J.

2007-01-01

Selected micrometeorological and soil-moisture data were collected at the Amargosa Desert Research Site adjacent to a low-level radio-active waste and hazardous chemical waste facility near Beatty, Nevada, 2001-05. Evapotranspiration data were collected from February 2002 through the end of December 2005. Data were col-lected in support of ongoing research to improve the understanding of hydrologic and contaminant-transport processes in arid environments. Micrometeorological data include solar radiation, net radiation, air temperature, relative humidity, saturated and ambient vapor pressure, wind speed and direction, barometric pressure, precipitation, near-surface soil temperature, soil-heat flux and soil-water content. All micrometeorological data were collected using a 10-second sampling interval by data loggers that output daily and hourly mean values. Daily maximum and minimum values are based on hourly mean values. Precipitation data output includes daily and hourly totals. Selected soil-moisture profiles at depth include periodic measurements of soil volumetric water-content measurements at nine neutron-probe access tubes to depths ranging from 5.25 to 29.25 meters. Evapotranspiration data include measurement of daily evapotranspiration and 15-minute fluxes of the four principal energy budget components of latent-heat flux, sensible-heat flux, soil-heat flux, and net radiation. Other data collected and used in equations to determine evapotranspiration include temperature and water content of soil, temperature and vapor pressure of air, and covariance values. Evapotranspiration and flux estimates during 15-minute intervals were calculated at a 0.1-second execution interval using the eddy covariance method. Data files included in this report contain the complete micrometeorological, soil-moisture, and evapotranspiration field data sets. These data files are presented in tabular Excel spreadsheet format. This report highlights selected data contained in the computer generated data files using figures, tables, and brief discussions. Instrumentation used for data collection also is described. Water-content profiles are shown to demonstrate variability of water content with depth. Time-series data are plotted to illustrate temporal variations in micrometeorological, soil-water content, and evapotranspiration data.

Co-composting of green waste and food waste at low C/N ratio

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Mathava; Ou, Y.-L.; Lin, J.-G., E-mail: jglin@mail.nctu.edu.t

2010-04-15

In this study, co-composting of food waste and green waste at low initial carbon to nitrogen (C/N) ratios was investigated using an in-vessel lab-scale composting reactor. The central composite design (CCD) and response surface method (RSM) were applied to obtain the optimal operating conditions over a range of preselected moisture contents (45-75%) and C/N ratios (13.9-19.6). The results indicate that the optimal moisture content for co-composting of food waste and green waste is 60%, and the substrate at a C/N ratio of 19.6 can be decomposed effectively to reduce 33% of total volatile solids (TVS) in 12 days. The TVSmore » reduction can be modeled by using a second-order equation with a good fit. In addition, the compost passes the standard germination index of white radish seed indicating that it can be used as soil amendment.« less

Fungal and fumonisins contamination in Argentine maize (Zea mays L.) silo bags.

PubMed

Pacin, Ana M; Ciancio Bovier, Emilia; González, Héctor H L; Whitechurch, Elena M; Martínez, Elena J; Resnik, Silvia L

2009-04-08

Fumonisins in maize (Zea mays L.) grain silo bags in the conditions of three Argentine provinces were analyzed to determine how this kind of storage affects contamination and if differential storage durations or times of the year of silo bag closing and opening are factors that could modify it. Moisture content, water activity (a(w)), molds and yeasts present, and fumonisins were analyzed in 163 maize silo bags, at the moment of closing and later at opening. Storage durations ranged from 120 to 226 days. The analysis was centered on fumonisins since most samples were only contaminated with these toxins. Fumonisins, moisture content, and a(w) increased significantly, whereas mold propagules/g and yeasts CFU/g did not present significant differences between silo opening and closing. The date on which silo bags were closed and later opened, however, did affect the level of fumonisin contamination.

High-rate composting of barley dregs with sewage sludge in a pilot scale bioreactor.

PubMed

Lu, Li-An; Kumar, Mathava; Tsai, Jen-Chieh; Lin, Jih-Gaw

2008-05-01

The feasibility of high-rate composting of barley dregs and sewage sludge was examined using a pilot scale bioreactor. A central composite design (CCD) was used to optimize the mix ratio of barley dregs/sewage sludge and moisture content. The performance of the bioreactor was monitored as a function of carbon decomposition rate (CDR) and total volatile solids (TVS) loss rate. The optimum range of mix ratio and moisture content was found to be 35-40% and 55-60%, respectively. High CO2 evolution rate (CER) and TVS loss rate were observed after 3 days of the composting and the compost was matured/stable after 7 days. Cardinal temperature model with inflection (CTMI) was used to analyze the compost stability with respect to CER as a parameter of composting efficiency. After examining the phytotoxicity, the compost can be promoted for land application.

The effect of moisture content on solid-state anaerobic digestion of dairy manure from a sawdust-bedded pack barn

USDA-ARS?s Scientific Manuscript database

The effect of moisture content on solid-state anaerobic digestion of dairy manure from a Korean sawdust-bedded pack barn was determined using laboratory-scale digesters operated at three moisture levels (70, 76, and 83% on a wet basis) at 37 C for 85 days. Results showed that digesters containing m...

Drying and control of moisture content and dimensional changes

Treesearch

William T. Simpson

1999-01-01

In the living tree, wood contains large quantities of water. As green wood dries, most of the water is removed. The moisture remaining in the wood tends to come to equilibrium with the relative humidity of the surrounding air. Correct drying, handling, and storage of wood will minimize moisture content changes that might occur after drying when the wood is in service...

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2010 CFR

2010-07-01

... moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with an inlet dryer temperature of less than or equal to 600 °F Maintaining the 24-hour block average inlet furnish moisture... temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood veneer dryer Process less...

40 CFR Table 8 to Subpart Dddd of... - Continuous Compliance With the Work Practice Requirements

Code of Federal Regulations, 2011 CFR

2011-07-01

... moisture content less than or equal to 30 percent (by weight, dry basis) AND operate with an inlet dryer temperature of less than or equal to 600 °F Maintaining the 24-hour block average inlet furnish moisture... temperature of furnish moisture content and inlet dryer temperature. (2) Hardwood veneer dryer Process less...

Controlling moisture content of wood samples using a modified soil-pan decay method

Treesearch

Jerrold E. Winandy; Simon F. Curling; Patricia K. Lebow

2005-01-01

In wood, the threshold level below which decay cannot occur varies with species or type of wood product and other factors such as temperature, humidity, and propensity of exposure or service-use to allow rain-induced wetting and subsequent drying. The ability to control wood moisture content (MC) during laboratory decay testing could allow research on the moisture...

Soil density and moisture content on two unused forest roads during first 30 months after construction

Treesearch

J.D. Helvey; J.N. Kochenderfer; J.N. Kochenderfer

1990-01-01

Reports results of soil density and soil moisture measurements on two roads in the central Appalachians over a 30-month period. Density increased slightly during the measurement period at most locations. Almost all of the density changes occurred during the first few months after construction. Moisture content decreased during the first few months after construction,...

Measurement of Moisture in Wood for Application in the Restoration of Old Buildings.

PubMed

Moron, Carlos; Garcia-Fuentevilla, Luisa; Garcia, Alfonso; Moron, Alberto

2016-05-14

There are many historic buildings whose construction is based on timber frame walls. Most buildings built during the nineteenth and early twentieth centuries were based on timber frame walls with vertical support elements. These timber frame elements are affected by their moisture content and by the passage of time. If the interaction of the timber frame walls with hygrothermal fluctuations were known, the maintenance of these buildings could be improved significantly. To determine the moisture content of wood there are two types of meters on the market: on the one hand, capacitance meters which consist of two side ends and where the moisture content is measured locally between two peaks. On the other hand, there are meters based on the variation of electromagnetic transmittance of timber, which depends on the moisture of timber. The second ones are very expensive and difficult to handle. This work presents a new non-intrusive capacitive sensor that measures the global moisture content in a section of the timber frame walls and therefore its accuracy is similar to the accuracy that can be obtained with electromagnetic transmittance meters. Additionally, as it is a capacitive sensor, it is low cost and easy to operate.

Measurement of Moisture in Wood for Application in the Restoration of Old Buildings

PubMed Central

Moron, Carlos; Garcia-Fuentevilla, Luisa; Garcia, Alfonso; Moron, Alberto

2016-01-01

There are many historic buildings whose construction is based on timber frame walls. Most buildings built during the nineteenth and early twentieth centuries were based on timber frame walls with vertical support elements. These timber frame elements are affected by their moisture content and by the passage of time. If the interaction of the timber frame walls with hygrothermal fluctuations were known, the maintenance of these buildings could be improved significantly. To determine the moisture content of wood there are two types of meters on the market: on the one hand, capacitance meters which consist of two side ends and where the moisture content is measured locally between two peaks. On the other hand, there are meters based on the variation of electromagnetic transmittance of timber, which depends on the moisture of timber. The second ones are very expensive and difficult to handle. This work presents a new non-intrusive capacitive sensor that measures the global moisture content in a section of the timber frame walls and therefore its accuracy is similar to the accuracy that can be obtained with electromagnetic transmittance meters. Additionally, as it is a capacitive sensor, it is low cost and easy to operate. PMID:27187410

Summer moisture contents of understory vegetation in northeastern Minnesota.

Treesearch

Robert M. Loomis; Peter J. Roussopoulos; Richard W. Blank

1979-01-01

Summer moisture contents and factors for converting fresh plant weights to ovendry biomass estimates are presented for some herbs, mosses, and small shrubs found in the upland forest stand of northeastern Minnesota.

Influence of moisture content and temperature on degree of carbonation and the effect on Cu and Cr leaching from incineration bottom ash.

PubMed

Lin, Wenlin Yvonne; Heng, Kim Soon; Sun, Xiaolong; Wang, Jing-Yuan

2015-09-01

This study investigated the influence of moisture content and temperature on the degree of carbonation of municipal solid waste (MSW) incineration bottom ash (IBA) from two different incineration plants in Singapore. The initial rate of carbonation was affected by the nominal moisture content used. Carbonation temperature seemed to play a part in changing the actual moisture content of IBA during carbonation, which in turn affected the degree of carbonation. Results showed that 2h of carbonation was sufficient for the samples to reach a relatively high degree of carbonation that was close to the degree of carbonation observed after 1week of carbonation. Both Cu and Cr leaching also showed significant reduction after only 2h of carbonation. Therefore, the optimum moisture content and temperature were selected based on 2h of carbonation. The optimum moisture content was 15% for both incineration plants while the optimum temperature was different for the two incineration plants, at 35°C and 50°C. The effect on Cu and Cr leaching from IBA after accelerated carbonation was evaluated as a function of carbonation time. Correlation coefficient, Pearson's R, was used to determine the dominant leaching mechanism. The reduction in Cu leaching was found to be contributed by both formation of carbonate mineral and reduction of DOC leaching. On the other hand, Cr leaching seemed to be dominantly controlled by pH. Copyright © 2015 Elsevier Ltd. All rights reserved.

Moisture distribution during conventional or electrical resistance oven baking of bread dough and subsequent storage.

PubMed

Derde, Liesbeth J; Gomand, Sara V; Courtin, Christophe M; Delcour, Jan A

2014-07-09

Electrical resistance oven (ERO) baking processes bread dough with little temperature gradient in the baking dough. Heating of the dough by means of an ERO is based on the principles of Joule's first law and Ohm's law. This study compared the changes in moisture distribution and physical changes in starch of breads conventionally baked or using an ERO. The moisture contents in fresh ERO breads are generally lower than those in conventional breads. During storage of conventionally baked breads, water migrates from the crumb to the crust and moisture contents decrease throughout the bread crumb. Evidently, less moisture redistribution occurs in ERO breads. Also, the protons of ERO bread constituents were less mobile than their counterparts in conventional bread. Starch retrogradation occurs to similar extents in conventional and ERO bread. As a result, the changes in proton mobility cannot be attributed to differences in levels of retrograded starch and seem to be primarily determined by the overall lower moisture content.

Evaluation of the sensitivity of the mineralizable pool of soil organic matter to changes in temperature and moisture

NASA Astrophysics Data System (ADS)

Tulina, A. S.; Semenov, V. M.

2015-08-01

The sensitivity of the potentially mineralizable pool of soil organic matter (Cpm) to changes in temperature and moisture has been assessed from the temperature coefficient ( Q10) and the moisture coefficient ( W 10), which indicate how much the Cpm size changes, when the temperature changes by 10°C and the soil water content changes by 10 wt %, respectively. Samples of gray forest soil, podzolized chernozem, and dark chestnut soil taken from arable plots have been incubated at 8, 18, and 28°C and humidity of 10, 25, and 40 wt %. From the data on the production of C-CO2 by soil samples during incubation for 150 days, the content of Cpm has been calculated. It has been shown that, on average for the three soils, an increase in temperature accounts for 63% of the rise in the pool of potentially mineralizable organic matter, whereas an increase in moisture accounts for 8% of that rise. The temperature coefficients of the potentially mineralizable pool are 2.71 ± 0.64, 1.27 ± 0.20, and 1.85 ± 0.30 in ranges of 8-18, 18-28, and 8-28°C, respectively; the moisture coefficients are 1.19 ± 0.11, 1.09 ± 0.05, and 1.14 ± 0.06 in ranges of 10-25, 25-40, and 10-40 wt %, respectively. The easily mineralizable fraction (C1, k 1 > 0.1 days-1) of the active pool of soil organic matter is less sensitive to temperature than the hardly mineralizable fraction (C3, 0.01 > k 3 > 0.001 days-1); their Q 10 values are 0.91 ± 0.15 and 2.40 ± 0.31, respectively. On the contrary, the easily mineralizable fraction is more sensitive to moistening than the hardly mineralizable fraction: their W 10 values are 1.22 ± 0.06 and 1.03 ± 0.08, respectively. The intensification of mineralization with rising temperature and water content during a long-term incubation results in the exhausting of the active pool, which reduces the production of CO2 by the soils during the repeated incubation under similar conditions nonlimiting mineralization.

Visualization and understanding of the granulation liquid mixing and distribution during continuous twin screw granulation using NIR chemical imaging.

PubMed

Vercruysse, Jurgen; Toiviainen, Maunu; Fonteyne, Margot; Helkimo, Niko; Ketolainen, Jarkko; Juuti, Mikko; Delaet, Urbain; Van Assche, Ivo; Remon, Jean Paul; Vervaet, Chris; De Beer, Thomas

2014-04-01

Over the last decade, there has been increased interest in the application of twin screw granulation as a continuous wet granulation technique for pharmaceutical drug formulations. However, the mixing of granulation liquid and powder material during the short residence time inside the screw chamber and the atypical particle size distribution (PSD) of granules produced by twin screw granulation is not yet fully understood. Therefore, this study aims at visualizing the granulation liquid mixing and distribution during continuous twin screw granulation using NIR chemical imaging. In first instance, the residence time of material inside the barrel was investigated as function of screw speed and moisture content followed by the visualization of the granulation liquid distribution as function of different formulation and process parameters (liquid feed rate, liquid addition method, screw configuration, moisture content and barrel filling degree). The link between moisture uniformity and granule size distributions was also studied. For residence time analysis, increased screw speed and lower moisture content resulted to a shorter mean residence time and narrower residence time distribution. Besides, the distribution of granulation liquid was more homogenous at higher moisture content and with more kneading zones on the granulator screws. After optimization of the screw configuration, a two-level full factorial experimental design was performed to evaluate the influence of moisture content, screw speed and powder feed rate on the mixing efficiency of the powder and liquid phase. From these results, it was concluded that only increasing the moisture content significantly improved the granulation liquid distribution. This study demonstrates that NIR chemical imaging is a fast and adequate measurement tool for allowing process visualization and hence for providing better process understanding of a continuous twin screw granulation system. Copyright © 2013 Elsevier B.V. All rights reserved.

Developing a two-step heat treatment for inactivating desiccation-adapted Salmonella spp. in aged chicken litter.

PubMed

Chen, Zhao; Wang, Hongye; Jiang, Xiuping

2015-02-01

The effectiveness of a two-step heat treatment for eliminating desiccation-adapted Salmonella spp. in aged chicken litter was evaluated. The aged chicken litter with 20, 30, 40, and 50% moisture contents was inoculated with a mixture of four Salmonella serotypes for a 24-h adaptation. Afterwards, the inoculated chicken litter was added into the chicken litter with the adjusted moisture content for a 1-h moist-heat treatment at 65 °C and 100% relative humidity inside a water bath, followed by a dry-heat treatment in a convection oven at 85 °C for 1 h to the desired moisture level (<10-12%). After moist-heat treatment, the populations of Salmonella in aged chicken litter at 20 and 30% moisture contents declined from ≈6.70 log colony-forming units (CFU)/g to 3.31 and 3.00 log CFU/g, respectively. After subsequent 1-h dry-heat treatment, the populations further decreased to 2.97 and 2.57 log CFU/g, respectively. Salmonella cells in chicken litter with 40% and 50% moisture contents were only detectable by enrichment after 40 and 20 min of moist-heat treatment, respectively. Moisture contents in all samples were reduced to <10% after a 1-h dry-heat process. Our results demonstrated that the two-step heat treatment was effective in reducing >5.5 logs of desiccation-adapted Salmonella in aged chicken litter with moisture content at or above 40%. Clearly, the findings from this study may provide the chicken litter processing industry with an effective heat treatment method for producing Salmonella-free chicken litter.

Further experimentation on bubble generation during transformer overload. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Oommen, T.V.

1992-03-01

This report covers additional work done during 1990 and 1991 on gas bubble generation under overload conditions. To improve visual bubble detection, a single disc coil was used. To further improve detection, a corona device was also used which signaled the onset of corona activity in the early stages of bubble formation. A total of fourteen model tests were conducted, half of which used the Inertaire system, and the remaining, a conservator (COPS). Moisture content of paper in the coil varied from 1.0% to 8.0%; gas (nitrogen) content varied from 1.0% to 8.8%. The results confirmed earlier observations that themore » mathematical bubble prediction model was not valid for high gas content model with relatively low moisture levels in the coil. An empirical relationship was formulated to accurately predict bubble evolution temperatures from known moisture and gas content values. For low moisture content models (below 2%), the simple Piper relationship was sufficient to predict bubble evolution temperatures, regardless of gas content. Moisture in the coil appears to be the key factor in bubble generation. Gas blanketed (Inertaire) systems do not appear to be prone to premature bubble generation from overloads as previously thought. The new bubble prediction model reveals that for a coil with 2% moisture, the bubble evolution temperature would be about 140{degrees}C. Since old transformers in service may have as much as 2% moisture in paper, the 140{degrees}C bubble evolution temperature may be taken as the lower limit of bubble evolution temperature under overload conditions for operating transformers. Drier insulation would raise the bubble evolution temperature.« less

Pore-scale investigation on the response of heterotrophic respiration to moisture conditions in heterogeneous soils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yan, Zhifeng; Liu, Chongxuan; Todd-Brown, Katherine E.

The relationship between microbial respiration rate and soil moisture content is an important property for understanding and predicting soil organic carbon degradation, CO 2 production and emission, and their subsequent effects on climate change. This paper reports a pore-scale modeling study to investigate the response of heterotrophic respiration to moisture conditions in soils and to evaluate various factors that affect this response. X-ray computed tomography was used to derive soil pore structures, which were then used for pore-scale model investigation. The pore-scale results were then averaged to calculate the effective respiration rates as a function of water content in soils.more » The calculated effective respiration rate first increases and then decreases with increasing soil water content, showing a maximum respiration rate at water saturation degree of 0.75 that is consistent with field and laboratory observations. The relationship between the respiration rate and moisture content is affected by various factors, including pore-scale organic carbon bioavailability, the rate of oxygen delivery, soil pore structure and physical heterogeneity, soil clay content, and microbial drought resistivity. Simulations also illustrates that a larger fraction of CO 2 produced from microbial respiration can be accumulated inside soil cores under higher saturation conditions, implying that CO 2 flux measured on the top of soil cores may underestimate or overestimate true soil respiration rates under dynamic moisture conditions. Overall, this study provides mechanistic insights into the soil respiration response to the change in moisture conditions, and reveals a complex relationship between heterotrophic microbial respiration rate and moisture content in soils that is affected by various hydrological, geochemical, and biophysical factors.« less

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2013 CFR

2013-10-01

... in this section— (1) Cargo subject to liquefaction means a material that is subject to moisture migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2014 CFR

2014-10-01

... in this section— (1) Cargo subject to liquefaction means a material that is subject to moisture migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...

46 CFR 148.450 - Cargoes subject to liquefaction.

Code of Federal Regulations, 2012 CFR

2012-10-01

... in this section— (1) Cargo subject to liquefaction means a material that is subject to moisture migration and subsequent liquefaction if shipped with moisture content in excess of the transportable moisture limit. (2) Moisture migration is the movement of moisture by settling and consolidation of a...

Predicting moisture dynamics of fine understory fuels in a moist tropical rainforest system: results of a pilot study undertaken to identify proxy variables useful for rating fire danger.

PubMed

Ray, David; Nepstad, Dan; Brando, Paulo

2010-08-01

*The use of fire as a land management tool in the moist tropics often has the unintended consequence of degrading adjacent forest, particularly during severe droughts. Reliable models of fire danger are needed to help mitigate these impacts. *Here, we studied the moisture dynamics of fine understory fuels in the east-central Brazilian Amazon during the 2003 dry season. Drying stations established under varying amounts of canopy cover (leaf area index (LAI) = 0 - 5.3) were subjected to a range of water inputs (5-15 mm) and models were developed to forecast litter moisture content (LMC). Predictions were then compared with independent field data. *A multiple linear regression relating litter moisture content to forest structure (LAI), ambient vapor pressure deficit (VPD(M)) and an index of elapsed time since a precipitation event (d(-1)) was identified as the best-fit model (adjusted R(2) = 0.89). Relative to the independent observations, model predictions were relatively unbiased when the LMC was

Spatiotemporal surface moisture dynamics on a coastal beach

NASA Astrophysics Data System (ADS)

Smit, Y.; Donker, J.; Ruessink, G.

2017-12-01

Surface moisture strongly controls aeolian transport on a beach and, accordingly, understanding its spatiotemporal variability will aid in developing a predictive model for the aeolian input of wind-blown beach sand into the foredune. In our earlier work (Smit et al., 2017, Aeolian Research) we have illustrated that the reflectance signal of a near-infrared Terrestrial Laser Scanner (TLS) corresponds well to gravimetric surface moisture content (in %) over its full range. Here, we analyze TLS-derived surface moisture maps with a 1x1 m spatial and a 15-min temporal resolution and concurrent groundwater measurements collected during a falling and rising tide at Egmond beach, the Netherlands. The maps show that the beach can be conceptualized into three surface moisture zones. First, the swash zone: 18% - 25%. Second, the intertidal zone: 5% - 25% (large fluctuations). A striking result for this zone is that surface moisture can decrease with a rate varying between 2.5% - 4% per hour, and cumulatively 16% during a single falling tide. And third, the back beach zone: 3% - 7%. During falling tide surface moisture fluctuations are strongly linked to the behavior of groundwater depth. A clear `Van Genuchten-type' retention curve can describe the relation between the two. Furthermore, no anticipated processes by capillary forces were observed in advance of the rising tide and no hysteresis was observed over de complete tidal cycle. Concluding, the TLS-derived moisture maps and the groundwater measurements clearly show that groundwater depth is the key control on spatiotemporal surface moisture variations.

Evaluation of the cosmic-ray neutron method for measuring integral soil moisture dynamics of a forested head water catchment

NASA Astrophysics Data System (ADS)

Bogena, H. R.; Metzen, D.; Baatz, R.; Hendricks Franssen, H.; Huisman, J. A.; Montzka, C.; Vereecken, H.

2011-12-01

Measurements of low-energy secondary neutron intensity above the soil surface by cosmic-ray soil moisture probes (CRP) can be used to estimate soil moisture content. CRPs utilise the fact that high-energy neutrons initiated by cosmic rays are moderated (slowed to lower energies) most effectively by collisions with hydrogen atoms contained in water molecules in the soil. The conversion of neutron intensity to soil moisture content can potentially be complicated because neutrons are also moderated by aboveground water storage (e.g. vegetation water content, canopy storage of interception). Recently, it was demonstrated experimentally that soil moisture content derived from CRP measurements agrees well with average moisture content from gravimetric soil samples taken within the footprint of the cosmic ray probe, which is proposed to be up to several hundred meters in size [1]. However, the exact extension and shape of the CRP integration footprint is still an open question and it is also unclear how CRP measurements are affected by the soil moisture distribution within the footprint both in horizontal and vertical directions. In this paper, we will take advantage of an extensive wireless soil moisture sensor network covering most of the estimated footprint of the CRP. The network consists of 150 nodes and 900 soil moisture sensors which were installed in the small forested Wüstebach catchment (~27 ha) in the framework of the Transregio32 and the Helmholtz initiative TERENO (Terrestrial Environmental Observatories) [2]. This unique soil moisture data set provides a consistent picture of the hydrological status of the catchment in a high spatial and temporal resolution and thus the opportunity to evaluate the CRP measurements in a rigorous way. We will present first results of the comparison with a specific focus on the sensitivity of the CRP measurements to soil moisture variation in both the horizontal and vertical direction. Furthermore, the influence of forest biomass and shallow groundwater table fluctuations on the attenuation of cosmic-ray neutrons will be considered.

Moisture and shelf life in sugar confections.

PubMed

Ergun, R; Lietha, R; Hartel, R W

2010-02-01

From hardening of marshmallow to graining of hard candies, moisture plays a critical role in determining the quality and shelf life of sugar-based confections. Water is important during the manufacturing of confections, is an important factor in governing texture, and is often the limiting parameter during storage that controls shelf life. Thus, an understanding of water relations in confections is critical to controlling quality. Water content, which is controlled during candy manufacturing through an understanding of boiling point elevation, is one of the most important parameters that governs the texture of candies. For example, the texture of caramel progresses from soft and runny to hard and brittle as the moisture content decreases. However, knowledge of water content by itself is insufficient to controlling stability and shelf life. Understanding water activity, or the ratio of vapor pressures, is necessary to control shelf life. A difference in water activity, either between candy and air or between two domains within the candy, is the driving force for moisture migration in confections. When the difference in water activity is large, moisture migration is rapid, although the rate of moisture migration depends on the nature of resistances to water diffusion. Barrier packaging films protect the candy from air whereas edible films inhibit moisture migration between different moisture domains within a confection. More recently, the concept of glass transition, or the polymer science approach, has supplemented water activity as a critical parameter related to candy stability. Confections with low moisture content, such as hard candy, cotton candy, and some caramels and toffees, may contain sugars in the amorphous or glassy state. As long as these products remain below their glass transition temperature, they remain stable for very long times. However, certain glassy sugars tend to be hygroscopic, rapidly picking up moisture from the air, which causes significant changes that lead to the end of shelf life. These products need to be protected from moisture uptake during storage. This review summarizes the concepts of water content, water activity, and glass transition and documents their importance to quality and shelf life of confections.

Modeling soil heating and moisture transport under extreme conditions: Forest fires and slash pile burns

NASA Astrophysics Data System (ADS)

Massman, W. J.

2012-10-01

Heating any soil during a sufficiently intense wildfire or prescribed burn can alter it irreversibly, causing many significant, long-term biological, chemical, and hydrological effects. Given the climate-change-driven increasing probability of wildfires and the increasing use of prescribed burns by land managers, it is important to better understand the dynamics of the coupled heat and moisture transport in soil during these extreme heating events. Furthermore, improved understanding and modeling of heat and mass transport during extreme conditions should provide insights into the associated transport mechanisms under more normal conditions. The present study describes a numerical model developed to simulate soil heat and moisture transport during fires where the surface heating often ranges between 10,000 and 100,000 W m-2 for several minutes to several hours. Basically, the model extends methods commonly used to model coupled heat flow and moisture evaporation at ambient conditions into regions of extreme dryness and heat. But it also incorporates some infrequently used formulations for temperature dependencies of the soil specific heat, thermal conductivity, and the water retention curve, as well as advective effects due to the large changes in volume that occur when liquid water is rapidly volatilized. Model performance is tested against laboratory measurements of soil temperature and moisture changes at several depths during controlled heating events. Qualitatively, the model agrees with the laboratory observations, namely, it simulates an increase in soil moisture ahead of the drying front (due to the condensation of evaporated soil water at the front) and a hiatus in the soil temperature rise during the strongly evaporative stage of the soil drying. Nevertheless, it is shown that the model is incapable of producing a physically realistic solution because it does not (and, in fact, cannot) represent the relationship between soil water potential and soil moisture at extremely low soil moisture contents (i.e., residual or bound water: θ < 0.01 m3 m-3, for example). Diagnosing the model's performance yields important insights into how to make progress on modeling soil evaporation and heating under conditions of high temperatures and very low soil moisture content.

Comparison of Microwave and Conventional Heating of a Wheat Starch-Gluten Model System

NASA Astrophysics Data System (ADS)

Umbach, Sharon Lynn

The effects of conventional (CV) and microwave (MW) heating on a model wheat starch, vital wheat gluten system were studied. Three moisture contents (35%, 50%, and 65%) and up to five ratios of starch:gluten were studied. MW power was such that heating took place more quickly than during CV heating conditions. Temperature profiles during heating showed the importance of moisture content for curve shape and that all samples reached a high enough temperature for starch gelatinization and gluten denaturation to occur. Scanning electron microscopy supported temperature data in that physical changes for starch had taken place. Texture was evaluated as the force required to compress the sample. Differences were found for heating method, moisture content, and sample composition. Moisture content had the major effect and was inversely related to force. In general, CV heated samples required more force to compress than the MW heated samples. The high starch samples at 50% moisture showed the opposite affect. Self-diffusion coefficients determined by nuclear magnetic resonance (NMR) showed that there was a redistribution of water between starch and gluten after heating for the faster more mobile water in the samples. Little difference was found between the two heating methods. The attenuation factor which has based on the dielectric constant and loss showed differences in the way the sample interacted with electromagnetic energy. The gluten was fractioned with dilute HCl to give six groups of protein. Starch appeared to have an effect on how the gluten denatured. When the fractions were characterized with SDS-PAGE it was found that each fraction contained a wide range of proteins with different molecular weights. Differences were found in the band patterns between the CV- and MW -heated samples. ^{13}C NMR also was used, which provided information on the protein and carbohydrate component of the fractions showed differences between the CV and MW heated samples, especially for the carbohydrate component. From this study, it appears that differences between the CV and MW heated samples are due to the type of denaturation the gluten undergoes, which may be influenced by the presence of starch and the amount of water available.

Measuring duff moisture content in the field using a portable meter sensitive to dielectric permittivity

Treesearch

Peter R. Robichaud; D. S. Gasvoda; Roger D. Hungerford; J. Bilskie; Louise E. Ashmun; J. Reardon

2004-01-01

Duff water content is an important consideration for fire managers when determining favourable timing for prescribed fire ignition. The duff consumption during burning depends largely on the duff water content at the time of ignition. A portable duff moisture meter was developed for real-time water content measurements of nonhomogenous material such as forest duff....

Effect of packaging materials on the chemical composition and microbiological quality of edible mushroom (Pleurotus ostreatus) grown on cassava peels.

PubMed

Ajayi, Oluwakemi; Obadina, Adewale; Idowu, Micheal; Adegunwa, Mojisola; Kajihausa, Olatundun; Sanni, Lateef; Asagbra, Yemisi; Ashiru, Bolanle; Tomlins, Keith

2015-07-01

Edible fungi such as mushrooms are highly perishable and deteriorate few days after harvest due to its high moisture content and inability to maintain their physiological status. In this study, the effect of packaging materials on the nutritional composition of mushroom cultivated from cassava peels was investigated. Mushroom samples were dried at 50°C in a cabinet dryer for 8 h. The dried mushroom samples packaged in four different packaging materials; high density polyethylene (HDPE), polypropylene (PP), laminated aluminum foil (LAF), high density polyethylene under vacuum (HDPEV) were stored at freezing (0°C) temperatures for 12 weeks. Samples were collected at 2-week intervals and analyzed for proximate composition (carbohydrate, protein, fat, fiber, ash, moisture), mineral content (calcium, potassium), vitamin C content, and microbiological qualities (total aerobic count, Pseudomonal count, Coliform count, Staphylococcal count, Salmonella count) using the standard laboratory procedures. Carbohydrate, protein, fat content of dried mushrooms packaged in HDPE at freezing temperature ranged from 45.2% to 53.5%, 18.0% to 20.3%, and 3.2% to 4.3%, while mushrooms in polypropylene ranged from 45.2% to 53.5%, 18.5% to 20.3%, 2.6% to 4.3%. Carbohydrate, protein, fat of mushroom in LAF ranged from 47.8% to 53.5%, 17.3% to 20.3%, and 3.3% to 4.3%, respectively, while carbohydrate, protein, fat of mushroom in HDPEV ranged from 51.1% to 53.5%, 19.5% to 20.3%, and 3.5% to 4.3%. Microbiological analysis showed that total aerobic count, Pseudomonal count, and Staphyloccocal count of dried mushroom ranged from 2.3 to 3.8 log cfu/g, 0.6 to 1.1 log cfu/g, and 0.4 to 0.5 log cfu/g, respectively. In conclusion, dried mushroom in HDPE packaged under vacuum at freezing temperature retained the nutritional constituents than those packaged with other packaging materials.

Effect of packaging materials on the chemical composition and microbiological quality of edible mushroom (Pleurotus ostreatus) grown on cassava peels

PubMed Central

Ajayi, Oluwakemi; Obadina, Adewale; Idowu, Micheal; Adegunwa, Mojisola; Kajihausa, Olatundun; Sanni, Lateef; Asagbra, Yemisi; Ashiru, Bolanle; Tomlins, Keith

2015-01-01

Edible fungi such as mushrooms are highly perishable and deteriorate few days after harvest due to its high moisture content and inability to maintain their physiological status. In this study, the effect of packaging materials on the nutritional composition of mushroom cultivated from cassava peels was investigated. Mushroom samples were dried at 50°C in a cabinet dryer for 8 h. The dried mushroom samples packaged in four different packaging materials; high density polyethylene (HDPE), polypropylene (PP), laminated aluminum foil (LAF), high density polyethylene under vacuum (HDPEV) were stored at freezing (0°C) temperatures for 12 weeks. Samples were collected at 2-week intervals and analyzed for proximate composition (carbohydrate, protein, fat, fiber, ash, moisture), mineral content (calcium, potassium), vitamin C content, and microbiological qualities (total aerobic count, Pseudomonal count, Coliform count, Staphylococcal count, Salmonella count) using the standard laboratory procedures. Carbohydrate, protein, fat content of dried mushrooms packaged in HDPE at freezing temperature ranged from 45.2% to 53.5%, 18.0% to 20.3%, and 3.2% to 4.3%, while mushrooms in polypropylene ranged from 45.2% to 53.5%, 18.5% to 20.3%, 2.6% to 4.3%. Carbohydrate, protein, fat of mushroom in LAF ranged from 47.8% to 53.5%, 17.3% to 20.3%, and 3.3% to 4.3%, respectively, while carbohydrate, protein, fat of mushroom in HDPEV ranged from 51.1% to 53.5%, 19.5% to 20.3%, and 3.5% to 4.3%. Microbiological analysis showed that total aerobic count, Pseudomonal count, and Staphyloccocal count of dried mushroom ranged from 2.3 to 3.8 log cfu/g, 0.6 to 1.1 log cfu/g, and 0.4 to 0.5 log cfu/g, respectively. In conclusion, dried mushroom in HDPE packaged under vacuum at freezing temperature retained the nutritional constituents than those packaged with other packaging materials. PMID:26288720

Novel soy protein scaffolds for tissue regeneration: Material characterization and interaction with human mesenchymal stem cells.

PubMed

Chien, Karen B; Shah, Ramille N

2012-02-01

Soy protein modified with heat treatment and enzyme crosslinking using transglutaminase in maltodextrin was used to fabricate novel, porous three-dimensional scaffolds through lyophilization. Physical properties of scaffolds were characterized using scanning electron microscopy, mercury intrusion porosimetry, moisture content analysis and mechanical testing. Human mesenchymal stem cells (hMSC) were seeded and cultured in vitro on the scaffolds for up to 2 weeks, and changes in stem cell growth and morphology were examined. The resulting scaffolds had rough surfaces, irregular pores with size distributions between 10 and 125 μm, <5% moisture content and compressive moduli ranging between 50 and 100 Pa. Enzyme treatment significantly lowered the moisture content. Increasing amounts of applied enzyme units lowered the median pore size. Although enzyme treatment did not affect the mechanical properties of the scaffolds, it did increase the degradation time by at least 1 week. These changes in scaffold degradation altered the growth and morphology of seeded hMSC. Cell proliferation was observed in scaffolds containing 3% soy protein isolate treated with 1 U of transglutaminase. These results demonstrate that controlling scaffold degradation rates is crucial for optimizing hMSC growth on soy protein scaffolds and that soy protein scaffolds have the potential to be used in tissue engineering applications. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Theoretical thermal conductivity equation for uniform density wood cells

Treesearch

John F. Hunt; Hongmei Gu; Patricia Lebow

2008-01-01

The anisotropy of wood creates a complex problem requiring that analyses be based on fundamental material properties and characteristics of the wood structure to solve heat transfer problems. A two-dimensional finite element model that evaluates the effective thermal conductivity of a wood cell over the full range of moisture contents and porosities was previously...

Stiffness and shrinkage of green and dry joists

Treesearch

Lyman W. Wood; Lawrence A. Soltis

1964-01-01

This report gives information on the edgewise modulus of elasticity, stiffness, and shrinkage of 360 joists in three species, three grades, and two sizes, each species obtained from two sources. Each joist was evaluated nondestructively at four moisture content values ranging from the green condition to about 11 percent. Information is also given on specific gravity,...

Campomanesia adamantium (Cambess.) O. Berg seed desiccation: influence on vigor and nucleic acids.

PubMed

Dresch, Daiane M; Masetto, Tathiana E; Scalon, Silvana P Q

2015-01-01

The aim of this study was to evaluate the sensitivity of Campomanesia adamantium seeds to desiccation by drying in activated silica gel (fast) and under laboratory conditions (slow). To assess the sensitivity of the seeds to desiccation, we used drying with silica gel and drying under laboratory conditions (25 °C), in order to obtain seeds with moisture content of 45, 35, 30, 25, 20, 15, 10 and 5%. The physiological potential of the seeds after desiccation was evaluated by measuring primary root protrusion, percentage of normal seedlings, germination seed index, seedling length, total seedling dry mass, electrical conductivity and DNA and RNA integrities. The C. adamantium seeds were sensitive to desiccation and to a reduction in moisture content to 21.1% or less by desiccation using silica gel, and to 17.2% or less by desiccation under laboratory conditions; impairment of the physiological potential of the seeds was observed at these low moisture content levels. The integrity of the seed genomic DNA was not affected after drying seeds in the two methods. However, drying in silica gel to 4.5% moisture content and drying under laboratory conditions to 5.4% moisture content resulted in the loss of seed RNA integrity.

Effects of moisture content on mechanical properties, transparency, and thermal stability of yuba film.

PubMed

Zhang, Siran; Kim, Nayeon; Yokoyama, Wallace; Kim, Yookyung

2018-03-15

Yuba is the skin formed at the surface during the heating of soymilk. The 3rd, 7th, and 11th films were evaluated for properties at different RH. At 39% RH, the 11th film had the lowest moisture, while the 3rd film had the highest moisture. However, at 75% RH, reverse moisture results were obtained. The tensile strengths of the 3rd and 11th films were highest at 15% moisture, whereas the tensile strength of the 7th film was highest at 25% moisture. Elongation of the 3rd (127%) and 11th (85%) films were highest at 25% moisture. The light transmittance of the films was low and opaque at 5% moisture. The films were transparent at 23%-28% moisture, but became opaque as the moisture increased. The films at 39% RH (ΔH, 113-203J/g) had higher thermal stability than those at 87% RH (ΔH, 315-493J/g). Moisture content markedly changed the yuba film properties. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nicotine quantity and packaging disclosure in smoked and smokeless tobacco products in India.

PubMed

Sharma, Priyamvada; Murthy, Pratima; Shivhare, Parul

2015-01-01

A variety of smoked and smokeless tobacco products with varying nicotine content are accessible in India. Nicotine quantity in tobacco products has direct bearing on tobacco dependence. Our objective was to estimate nicotine content in various types of smoked and smokeless products. Disclosure for essential health warning was also checked. Liquid-liquid extraction was used for nicotine extraction and high-performance thin layer chromatography technique was applied for quantification of nicotine in seventy-one smoked and smokeless tobacco products. Significant variation in nicotine content was observed across products. In smoked tobacco, nicotine content varied from 1.01 to 13.0 mg/rod, while in smokeless tobacco products it ranged from 0.8 mg/g to 50.0 mg/g. Moisture content varied from 9% to 21%. This work lists a range of smoked and smokeless tobacco products available in this region. We report a wide variability in nicotine quantity across smoked and smokeless tobacco products. Such variation in nicotine content may have important implications for tobacco cessation interventions and policies.

Moisture content during extrusion of oats impacts the initial fermentation metabolites and probiotic bacteria during extended fermentation by human fecal microbiota.

PubMed

Brahma, Sandrayee; Weier, Steven A; Rose, Devin J

2017-07-01

Extrusion exposes flour components to high pressure and shear during processing, which may affect the dietary fiber fermentability by human fecal microbiota. The objective of this study was to determine the effect of flour moisture content during extrusion on in vitro fermentation properties of whole grain oats. Extrudates were processed at three moisture levels (15%, 18%, and 21%) at fixed screw speed (300rpm) and temperature (130°C). The extrudates were then subjected to in vitro digestion and fermentation. Extrusion moisture significantly affected water-extractable β-glucan (WE-BG) in the extrudates, with samples processed at 15% moisture (lowest) and 21% moisture (highest) having the highest concentration of WE-BG. After the first 8h of fermentation, more WE-BG remained in fermentation media in samples processed at 15% moisture compared with the other conditions. Also, extrusion moisture significantly affected the production of acetate, butyrate, and total SCFA by the microbiota during the first 8h of fermentation. Microbiota grown on extrudates processed at 18% moisture had the highest production of acetate and total SCFA, whereas bacteria grown on extrudates processed at 15% and 18% moisture had the highest butyrate production. After 24h of fermentation, samples processed at 15% moisture supported lower Bifidobacterium counts than those produced at other conditions, but had among the highest Lactobacillus counts. Thus, moisture content during extrusion significantly affects production of fermentation metabolites by the gut microbiota during the initial stages of fermentation, while also affecting probiotic bacteria counts during extended fermentation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Characterization of Physico-Chemical Properties and Antioxidant Capacities of Bioactive Honey Produced from Australian Grown Agastache rugosa and its Correlation with Colour and Poly-Phenol Content.

PubMed

Anand, Sushil; Pang, Edwin; Livanos, George; Mantri, Nitin

2018-01-05

The antioxidant and antimicrobial components of honey vary based on sourced of nectar. Medicinal plants with the therapeutic value have potential to produce honey with greater bioactivity. The aim of the present study was to characterize the physico-chemical and antioxidant capacities of Agastache honey produced from Agastache rugosa and compare them with other popular commercial honeys sold in Australia. The total phenolics, total flavonoids, moisture content, colour, pH, protein content and antioxidant capacity were evaluated for Agastache , Manuka, Jelly bush, Tea tree, Super manuka and Jarrah honeys. The results reveal that the moisture content ranged from 17-21%, pH ranged from 3.8-4.3 and estimated protein content ranged from 900-2200 µg/g. The DPPH•, ABTS•+, ORAC and FRAP methods were used to measure the antioxidant capacity of the honey samples. The DPPH• % inhibition, ABTS•+, ORAC and FRAP values for Agastache honey were 9.85 (±1.98 µmol TE/g), 26.88 (±0.32 µmol TE/g), 19.78 (±1.1 µmol TE/g) and 3.61 (±0.02 µmol TE/g) whereas the highest antioxidant capacity values obtained were 18.69 (±0.9 µmol TE/g), 30.72 (±0.27 µmol TE/g), 26.95 (±0.9 µmol TE/g) and 3.68 (±0.04 µmol TE/g), respectively. There was a positive correlation between colour, total phenolic content and DPPH• scavenging activity for most of the honeys except Tea tree honey. However, there was no clear correlation with ABTS•+, ORAC and FRAP values. The measured antioxidant capacity of samples varied with the assays used. The DPPH• assay clearly indicated that the phenolic compounds contribute to the scavenging activity of the honeys. Nevertheless, all assays confirm that Agastache honey has significant antioxidant capacity. Therefore, Agastache honey can be important to human nutrition and health.

Changes in protein and starch digestibility in sorghum flour during heat-moisture treatments.

PubMed

Vu, Thanh-Hien; Bean, Scott; Hsieh, Chao-Feng; Shi, Yong-Cheng

2017-11-01

Heat-moisture treatment (HMT) has been used to modify properties of sorghum starches. However, information is limited on the effects of HMT on the digestibility of starch and the concurrent changes in protein in sorghum flour. The objectives of this research were to identify heat-moisture conditions to increase the resistant starch (RS) content of sorghum flour and investigate changes in sorghum proteins and starch structure. Sorghum flours with different moisture contents (0, 125, 200, and 300 g kg -1 w.b.) were heated at three temperatures (100, 120 and 140 °C) and times (1, 2 and 4 h). HMT of sorghum flour increased its RS level. The flour treated at 200 g kg -1 moisture and 100 °C for 4 h had a high RS content (221 g kg -1 vs. 56 g kg -1 for the untreated flour). Starch was not gelatinized when sorghum flours heated at moisture content of 200 g kg -1 or below. Sorghum protein digestibility and solubility decreased during HMT. The increase in RS of sorghum flour upon HMT was attributed to enhanced amylose-lipid complexes and heat induced structural changes in its protein fraction. HMT can be used to increase RS content in sorghum flour without gelatinizing its starch, thereby providing sorghum flour with unique food applications. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Effects of size and moisture of rhizome on initial invasiveness ability of giant reed.

PubMed

Santín-Montanyá, M I; Jimenéz, J; Vilán, X M; Ocaña, L

2014-01-01

Studies were conducted under controlled conditions to determine growth and reproductive capabilities of Arundo donax L. (giant reed), a riparian invasive perennial plant that has spread widely. Greenhouse experiments were conducted to determine the influence of rhizome size and moisture content in the early invasiveness ability of giant reed. We tested different sizes of rhizomes: rhizome size of 1 cm, 3 cm, 5 cm and shredded rhizome. (fragments < 1 cm). These rhizomes were observed at 7, 14, 21, 28 and 35 days after planting (DAP). To test the effect of moisture content we used fresh rhizome fragments; rhizomes with moderate dehydration (50%); rhizomes with high dehydration (over 70%) with 48 hours of rehydration and rhizomes with high dehydration (70-90%). The rhizomes monitored for moisture content and biomass increase were between 3 and 5 cm, and were observed 60 DAP. The initial size of rhizomes affected the level of sprouting. Rhizomes with low moisture content (due to dehydration) showed high increase in biomass compared with the rhizomes that had not been treated or had been dehydrated and then rehydrated. Our results indicated that size of rhizomes is related to regrowth and low moisture (dehydration) content can be overcome by this species. This could be linked to high rates of colonization and early establishment ability of this species even after mechanical treatment of rhizomes, in riparian environments.

Examining the Effectiveness of Hacked, Commercial, Self-Tuning RFID Tags to Passively Sense the Volumetric Water Content of Soil

NASA Astrophysics Data System (ADS)

Stoddard, B. S.; Udell, C.; Selker, J. S.

2017-12-01

Currently available soil volumetric water content (VWC) sensors have several drawbacks that pose certain challenges for implementation on large scale for farms. Such issues include cost, scalability, maintenance, wires running through fields, and single-spot resolution. The development of a passive soil moisture sensing system utilizing Radio Frequency Identification (RFID) would allay many of these issues. The type of passive RFID tags discussed in this paper currently cost between 8 to 15 cents retail per tag when purchased in bulk. An incredibly cheap, scalable, low-maintenance, wireless, high-resolution system for sensing soil moisture would be possible if such tags were introduced into the agricultural world. This paper discusses both the use cases as well as examines one implementation of the tags. In 2015, RFID tag manufacturer SmarTrac started selling RFID moisture sensing tags for use in the automotive industry to detect leaks during quality assurance. We place those tags in soil at a depth of 4 inches and compared the moisture levels sensed by the RFID tags with the relative permittivity (ɛr) of the soil as measured by an industry-standard probe. Using an equation derived by Topp et al, we converted to VWC. We tested this over a wide range of moisture conditions and found a statistically significant, correlational relationship between the sensor values from the RFID tags and the probe's measurement of ɛr. We also identified a possible function for mapping vales from the RFID tag to the probe bounded by a reasonable margin of error.

Real-time soil sensing based on fiber optics and spectroscopy

NASA Astrophysics Data System (ADS)

Li, Minzan

2005-08-01

Using NIR spectroscopic techniques, correlation analysis and regression analysis for soil parameter estimation was conducted with raw soil samples collected in a cornfield and a forage field. Soil parameters analyzed were soil moisture, soil organic matter, nitrate nitrogen, soil electrical conductivity and pH. Results showed that all soil parameters could be evaluated by NIR spectral reflectance. For soil moisture, a linear regression model was available at low moisture contents below 30 % db, while an exponential model can be used in a wide range of moisture content up to 100 % db. Nitrate nitrogen estimation required a multi-spectral exponential model and electrical conductivity could be evaluated by a single spectral regression. According to the result above mentioned, a real time soil sensor system based on fiber optics and spectroscopy was developed. The sensor system was composed of a soil subsoiler with four optical fiber probes, a spectrometer, and a control unit. Two optical fiber probes were used for illumination and the other two optical fiber probes for collecting soil reflectance from visible to NIR wavebands at depths around 30 cm. The spectrometer was used to obtain the spectra of reflected lights. The control unit consisted of a data logging device, a personal computer, and a pulse generator. The experiment showed that clear photo-spectral reflectance was obtained from the underground soil. The soil reflectance was equal to that obtained by the desktop spectrophotometer in laboratory tests. Using the spectral reflectance, the soil parameters, such as soil moisture, pH, EC and SOM, were evaluated.

Updraft gasification of salmon processing waste.

PubMed

Rowland, Sarah; Bower, Cynthia K; Patil, Krushna N; DeWitt, Christina A Mireles

2009-10-01

The purpose of this study was to judge the feasibility of gasification for the disposal of waste streams generated through salmon harvesting. Gasification is the process of converting carbonaceous materials into combustible "syngas" in a high temperature (above 700 degrees C), oxygen deficient environment. Syngas can be combusted to generate power, which recycles energy from waste products. At 66% to 79% moisture, raw salmon waste streams are too wet to undergo pyrolysis and combustion. Ground raw or de-oiled salmon whole fish, heads, viscera, or frames were therefore "dried" by mixing with wood pellets to a final moisture content of 20%. Ground whole salmon with moisture reduced to 12% moisture was gasified without a drying agent. Gasification tests were performed in a small-scale, fixed-bed, updraft gasifer. After an initial start-up period, the gasifier was loaded with 1.5 kg of biomass. Temperature was recorded at 6 points in the gasifier. Syngas was collected during the short steady-state period during each gasifier run and analyzed. Percentages of each type of gas in the syngas were used to calculate syngas heating value. High heating value (HHV) ranged from 1.45 to 1.98 MJ/kg. Bomb calorimetry determined maximum heating value for the salmon by-products. Comparing heating values shows the efficiency of gasification. Cold gas efficiencies of 13.6% to 26% were obtained from the various samples gasified. Though research of gasification as a means of salmon waste disposal and energy production is ongoing, it can be concluded that pre-dried salmon or relatively low moisture content mixtures of waste with wood are gasifiable.

Microstrip Ring Resonator for Soil Moisture Measurements

NASA Technical Reports Server (NTRS)

Sarabandi, Kamal; Li, Eric S.

1993-01-01

Accurate determination of spatial soil moisture distribution and monitoring its temporal variation have a significant impact on the outcomes of hydrologic, ecologic, and climatic models. Development of a successful remote sensing instrument for soil moisture relies on the accurate knowledge of the soil dielectric constant (epsilon(sub soil)) to its moisture content. Two existing methods for measurement of dielectric constant of soil at low and high frequencies are, respectively, the time domain reflectometry and the reflection coefficient measurement using an open-ended coaxial probe. The major shortcoming of these methods is the lack of accurate determination of the imaginary part of epsilon(sub soil). In this paper a microstrip ring resonator is proposed for the accurate measurement of soil dielectric constant. In this technique the microstrip ring resonator is placed in contact with soil medium and the real and imaginary parts of epsilon(sub soil) are determined from the changes in the resonant frequency and the quality factor of the resonator respectively. The solution of the electromagnetic problem is obtained using a hybrid approach based on the method of moments solution of the quasi-static formulation in conjunction with experimental data obtained from reference dielectric samples. Also a simple inversion algorithm for epsilon(sub soil) = epsilon'(sub r) + j(epsilon"(sub r)) based on regression analysis is obtained. It is shown that the wide dynamic range of the measured quantities provides excellent accuracy in the dielectric constant measurement. A prototype microstrip ring resonator at L-band is designed and measurements of soil with different moisture contents are presented and compared with other approaches.

Moisture-strength-constructability guidelines for subgrade foundation soils found in Indiana.

DOT National Transportation Integrated Search

2016-09-01

Soil moisture is an important indicator of constructability in the field. Construction activities become difficult when the soil moisture content is excessive, especially in fine-grained soils. Change orders caused by excessive soil moisture during c...

Soil Moisture and Excavation Behaviour in the Chaco Leaf-Cutting Ant (Atta vollenweideri): Digging Performance and Prevention of Water Inflow into the Nest

PubMed Central

Pielström, Steffen; Roces, Flavio

2014-01-01

The Chaco leaf-cutting ant Atta vollenweideri is native to the clay-heavy soils of the Gran Chaco region in South America. Because of seasonal floods, colonies are regularly exposed to varying moisture across the soil profile, a factor that not only strongly influences workers' digging performance during nest building, but also determines the suitability of the soil for the rearing of the colony's symbiotic fungus. In this study, we investigated the effects of varying soil moisture on behaviours associated with underground nest building in A. vollenweideri. This was done in a series of laboratory experiments using standardised, plastic clay-water mixtures with gravimetric water contents ranging from relatively brittle material to mixtures close to the liquid limit. Our experiments showed that preference and group-level digging rate increased with increasing water content, but then dropped considerably for extremely moist materials. The production of vibrational recruitment signals during digging showed, on the contrary, a slightly negative linear correlation with soil moisture. Workers formed and carried clay pellets at higher rates in moist clay, even at the highest water content tested. Hence, their weak preference and low group-level excavation rate observed for that mixture cannot be explained by any inability to work with the material. More likely, extremely high moistures may indicate locations unsuitable for nest building. To test this hypothesis, we simulated a situation in which workers excavated an upward tunnel below accumulated surface water. The ants stopped digging about 12 mm below the interface soil/water, a behaviour representing a possible adaptation to the threat of water inflow field colonies are exposed to while digging under seasonally flooded soils. Possible roles of soil water in the temporal and spatial pattern of nest growth are discussed. PMID:24748382

Feasibility study of a V-shaped pipe for passive aeration composting.

PubMed

Ogunwande, Gbolabo A

2011-03-01

A V-shaped (Vs) pipe was improvised for composting of chicken litter in passive aeration piles. Three piles, equipped with horizontal (Ho), vertical (Ve) and Vs pipes were set up. The three treatments were replicated thrice. The effects of the aeration pipe on the physico-chemical properties of chicken litter and air distribution within the composting piles were investigated during composting. The properties monitored were temperature, pH, electrical conductivity, moisture content, total carbon, total nitrogen, total phosphorus and carbon-to-nitrogen ratio. Moisture level in the piles was replenished fortnightly to 60% during composting. The results of the study showed that all the piles attained the optimum temperature range (40-65°C) for effective composting and satisfied the requirements for sanitation. The non-significant (p > 0.05) temperature difference within the piles with Ve and Vs pipes indicated that these pipes were effective for uniform air distribution within the pile. The aeration pipe had significant (p ≤ 0.05) effect on pile temperature, pre-replenishment moisture content, pH and total phosphorus. In conclusion, the study showed that the Vs pipe is feasible and effective for passive aeration composting.

Impact of rainfall on the moisture content of large woody fuels

Treesearch

Helen H. Mohr; Thomas A. Waldrop

2013-01-01

This unreplicated case study evaluates the impact of rainfall on large woody fuels over time. We know that one rainfall event may decrease the Keetch-Byram Drought Index, but this study shows no real increase in fuel moisture in 1,000- hour fuels after just one rainfall. Several rain events over time are required for the moisture content of large woody fuels to...

Determining seed moisture in Quercus

Treesearch

F. T. Bonner

1974-01-01

The air-oven method with drying times 7 to 8 hours shorter than those now prescribed in the ISTA rules proved adequate for determining moisture contents in acorns of several North American oaks. Schedules of 8 hours at 105°C for Quercus muehlenbergii and 9 hours at 105°C for Q.shumardii and Q.nigra gave moisture contents within three percentage points of those obtained...

[Application of time domain reflectometry for determination of wate content in Xiangsha Yangwei pills].

PubMed

Long, Feng-Lai; Sun, Xiao-Mei; Peng, Xiu-Juan; Liu, Peng; He, Fang-Hui

2016-08-01

Xiangsha Yangwei pill was selected as a model drug in this research, and time domain reflectometry (TDR) was used to determine the water content in the pill. The effects of five factors including the number of pill layers, pill packing density, atmospheric moisture, ambient temperature and the ratio of pill formula were investigated on water content. The results showed that the number of pill layers and ambient temperature had significant effects on water content of pills, while the pill packing density, atmospheric moisture and pill formula ratio had little effect on the determination of water content in pills. The reflection value was stable when 6 layers of pills were used. Under the condition of 25 ℃ and 45% relative humidity, the water content of pills ranged from 4.01% to 22.38%, showing good linear relationship between water content and reflection value, and the model equation was as follows: Y=0.279X－21.670 (R²=0.997 0). Verification experiment was used to explain the feasibility of this prediction model. The precision of the method complied with the methodology standard. It is concluded that TDR can be used in determination of water content in Xiangsha Yangwei pills. Additionally, TDR, as a new way to quickly and efficiently determine the water content, has a prospect application in the processing of traditional Chinese medicine pharmacy, especially for concentrated pill. Copyright© by the Chinese Pharmaceutical Association.

Effect of temperature and relative humidity during transportation on green coffee bean moisture content and ochratoxin A production.

PubMed

Palacios-Cabrera, Hector A; Menezes, Hilary C; Iamanaka, Beatriz T; Canepa, Frederico; Teixeira, Aldir A; Carvalhaes, Nelson; Santi, Domenico; Leme, Plinio T Z; Yotsuyanagi, Katumi; Taniwaki, Marta H

2007-01-01

Changes in temperature, relative humidity, and moisture content of green coffee beans were monitored during transportation of coffee from Brazil to Italy. Six containers (three conventional and three prototype) were stowed in three different places (hold, first floor, and deck) on the ship. Each prototype was located next to a conventional container. The moisture content of the coffee in the container located on the first floor was less affected by environmental variations (0.7%) than that in the hold and on the deck. Coffee located in the hold showed the highest variation in moisture content (3%); in addition, the container showed visible condensation. Coffee transported on the deck showed an intermediary variation in moisture (2%), and there was no visible condensation. The variation in coffee moisture content of the prototype containers was similar to that of the conventional ones, especially in the top layers of coffee bags (2 to 3%), while the increase in water activity was 0.70. This suggests that diffusion of moisture occurs very slowly inside the cargo and that there are thus sufficient time and conditions for fungal growth. The regions of the container near the wall and ceiling are susceptible to condensation since they are close to the headspace with its high relative humidity. Ochratoxin A production occurred in coffee located at the top of the container on the deck and in the wet bags from the hold (those found to be wet on opening the containers at the final destination).

Electrical methods of determining soil moisture content

NASA Technical Reports Server (NTRS)

Silva, L. F.; Schultz, F. V.; Zalusky, J. T.

1975-01-01

The electrical permittivity of soils is a useful indicator of soil moisture content. Two methods of determining the permittivity profile in soils are examined. A method due to Becher is found to be inapplicable to this situation. A method of Slichter, however, appears to be feasible. The results of Slichter's method are extended to the proposal of an instrument design that could measure available soil moisture profile (percent available soil moisture as a function of depth) from a surface measurement to an expected resolution of 10 to 20 cm.

Preliminary assestment of lint cotton water content in gin-drying temperature studies

USDA-ARS?s Scientific Manuscript database

Prior studies to measure total water (free and bound) in lint cotton by Karl Fischer Titration showed the method is more accurate and precise than moisture content by standard oven drying. The objective of the current study was to compare the moisture and total water contents from five cultivars de...

Evaluation of the effect of synthetic fibers and non-woven geotextile reinforcement on the stability of heavy clay embankments : technical summary.

DOT National Transportation Integrated Search

2004-07-01

The objectives of this study were to evaluate the effects of soil density, moisture content, fiber content, and confining pressure on the shear strength of the clayey-fiber matrix, and of soil moisture content and confining pressure on the interface ...

Defatted wheat germ application: Influence on cookies' properties with regard to its particle size and dough moisture content.

PubMed

Petrović, Jovana; Rakić, Dušan; Fišteš, Aleksandar; Pajin, Biljana; Lončarević, Ivana; Tomović, Vladimir; Zarić, Danica

2017-10-01

The introduction of agro-food industry by-products rich in bioactive compounds represents major challenge in food industry sector. The influence of wheat germ particle size (<150 µm, 150-1000 µm, and 800-2000 µm), wheat germ content (5, 10, and 15%), and dough moisture content (20, 22, and 24%) on chemical, textural, and sensory characteristics of cookies was investigated using the Box-Behnken experimental design. The substitution of wheat flour with wheat germ increased the protein, fat, mineral, and fiber content of the cookies. The particle size of wheat germ affected the textural properties of cookies. As the particle size of wheat germ increased, the hardness of cookies decreased. The color of the cookie was most influenced by the interaction of dough moisture content and wheat germ particle size. Wheat germ level up to 15% had no significant effect on the sensory characteristics of cookies. A suitable combination of defatted wheat germ level, its particle size, and dough moisture content can improve the nutritional value of cookies, without causing a negative effect on the cookies' sensory characteristics.

Instrumentation for sensing moisture content of material using a transient thermal pulse

NASA Technical Reports Server (NTRS)

Yang, L. C. (Inventor)

1981-01-01

Instrumentation is developed for sensing moisture content of material using a transient thermal pulse and is comprised of a sensing probe having a sensing element in the form of a ribbon excited by a constant current pulse to increase the temperature, and therefore the resistance, of the ribbon linearly. Moisture in web material limits the increase of temperature during the pulse in proportion to the moisture content. This increase in temperature produces a proportional increase in resistivity which is measured with a Wheatsone bridge as a change in voltage displayed by a measurement display unit. The probe is glued in a shallow groove of a lucite bar and connected to copper pins embedded in the bar.

Soil moisture sensors for continuous monitoring

USGS Publications Warehouse

Amer, Saud A.; Keefer, T. O.; Weltz, M.A.; Goodrich, David C.; Bach, Leslie

1995-01-01

Certain physical and chemical properties of soil vary with soil water content. The relationship between these properties and water content is complex and involves both the pore structure and constituents of the soil solution. One of the most economical techniques to quantify soil water content involves the measurement of electrical resistance of a dielectric medium that is in equilibrium with the soil water content. The objective of this research was to test the reliability and accuracy of fiberglass soil-moisture electrical resistance sensors (ERS) as compared to gravimetric sampling and Time Domain Reflectometry (TDR). The response of the ERS was compared to gravimetric measurements at eight locations on the USDA-ABS Walnut Gulch Experimental Watershed. The comparisons with TDR sensors were made at three additional locations on the same watershed. The high soil rock content (>45 percent) at seven locations resulted in consistent overestimation of soil water content by the ERS method. Where rock content was less than 10 percent, estimation of soil water was within 5 percent of the gravimetric soil water content. New methodology to calibrate the ERS sensors for rocky soils will need to be developed before soil water content values can be determined with these sensors. (KEY TERMS: soil moisture; soil water; infiltration; instrumentation; soil moisture sensors.)

Effects of relaxation of gluten network on rehydration kinetics of pasta.

PubMed

Ogawa, Takenobu; Hasegawa, Ayako; Adachi, Shuji

2014-01-01

The aim of this study was to investigate the effects of the relaxation of the gluten network on pasta rehydration kinetics. The moisture content of pasta, under conditions where the effects of the diffusion of water on the moisture content were negligible, was estimated by extrapolating the average moisture content of pasta of various diameters to 0 mm. The moisture content of imaginary, infinitely thin pasta did not reach equilibrium even after 1 h of rehydration. The rehydration of pasta made of only gluten was also measured. The rate constants estimated by the Long and Richman equation for both the pasta indicated that the rehydration kinetics of infinitely thin pasta were similar to those of gluten pasta. These results suggest that the swelling of starch by fast gelatinization was restricted by the honeycomb structural network of gluten and the relaxation of the gluten network controlled pasta rehydration kinetics.

Impact of moisture content in AAC on its heat insulation properties

NASA Astrophysics Data System (ADS)

Rubene, S.; Vilnitis, M.

2017-10-01

One of the most popular trends in construction industry is sustainable construction. Therefore, application of construction materials with high insulation characteristics has significantly increased during the past decade. Requirements for application of construction materials with high insulation parameters are required not only by means of energy saving and idea of sustainable construction but also by legislative requirements. Autoclaved aerated concrete (AAC) is a load bearing construction material, which has high heat insulation parameters. However, if the AAC masonry construction has high moisture content the heat insulation properties of the material decrease significantly. This fact lead to the necessity for the on-site control of moisture content in AAC in order to avoid inconsistency between the designed and actual thermal resistivity values of external delimiting constructions. Research of the impact of moisture content in AAC on its heat insulation properties has been presented in this paper.

An update on potato crisps contents of moisture, fat, salt and fatty acids (including trans-fatty acids) with special emphasis on new oils/fats used for frying.

PubMed

Gonçalves Albuquerque, Tânia; Sanches-Silva, Ana; Santos, Lèlita; Costa, Helena S

2012-09-01

Eighteen brands of potato crisps, frequently consumed, were analyzed to establish their nutritional value in relation to salt, fat and fatty acid (FA) composition. The purpose of the present study was to determine moisture, total fat, salt contents and FA profiles (including trans-FAs), and to identify the oil/fat used for frying of the 18 brands of potato crisps. Our results show that salt content ranged from 0.127 to 2.77 g/100 g and total fat content of potato crisps varied between 20.0 and 42.8 g/100 g. With respect to FAs analysis, palmitic acid (C16:0), oleic acid (C18:1) and linoleic acid (C18:2) were the major FAs found in the analyzed potato crisps. It is clear from our work that nowadays most potato crisps are currently produced using oils with high contents in unsaturated FAs, which can be considered as healthier from a nutritional point of view. Nevertheless, some brands of potato crisps still use palm oil or a blend of palm oil and other fats/oils, which are very rich in saturated FAs.

A model of the CO2 exchanges between biosphere and atmosphere in the tundra

NASA Technical Reports Server (NTRS)

Labgaa, Rachid R.; Gautier, Catherine

1992-01-01

A physical model of the soil thermal regime in a permafrost terrain has been developed and validated with soil temperature measurements at Barrow, Alaska. The model calculates daily soil temperatures as a function of depth and average moisture contents of the organic and mineral layers using a set of five climatic variables, i.e., air temperature, precipitation, cloudiness, wind speed, and relative humidity. The model is not only designed to study the impact of climate change on the soil temperature and moisture regime, but also to provide the input to a decomposition and net primary production model. In this context, it is well known that CO2 exchanges between the terrestrial biosphere and the atmosphere are driven by soil temperature through decomposition of soil organic matter and root respiration. However, in tundra ecosystems, net CO2 exchange is extremely sensitive to soil moisture content; therefore it is necessary to predict variations in soil moisture in order to assess the impact of climate change on carbon fluxes. To this end, the present model includes the representation of the soil moisture response to changes in climatic conditions. The results presented in the foregoing demonstrate that large errors in soil temperature and permafrost depth estimates arise from neglecting the dependence of the soil thermal regime on soil moisture contents. Permafrost terrain is an example of a situation where soil moisture and temperature are particularly interrelated: drainage conditions improve when the depth of the permafrost increases; a decrease in soil moisture content leads to a decrease in the latent heat required for the phase transition so that the heat penetrates faster and deeper, and the maximum depth of thaw increases; and as excepted, soil thermal coefficients increase with moisture.

Hair Shaft Damage from Heat and Drying Time of Hair Dryer

PubMed Central

Lee, Yoonhee; Kim, Youn-Duk; Hyun, Hye-Jin; Pi, Long-quan; Jin, Xinghai

2011-01-01

Background Hair dryers are commonly used and can cause hair damage such as roughness, dryness and loss of hair color. It is important to understand the best way to dry hair without causing damage. Objective The study assessed changes in the ultra-structure, morphology, moisture content, and color of hair after repeated shampooing and drying with a hair dryer at a range of temperatures. Methods A standardized drying time was used to completely dry each hair tress, and each tress was treated a total of 30 times. Air flow was set on the hair dryer. The tresses were divided into the following five test groups: (a) no treatment, (b) drying without using a hair dryer (room temperature, 20℃), (c) drying with a hair dryer for 60 seconds at a distance of 15 cm (47℃), (d) drying with a hair dryer for 30 seconds at a distance of 10 cm (61℃), (e) drying with a hair dryer for 15 seconds at a distance of 5 cm (95℃). Scanning and transmission electron microscopy (TEM) and lipid TEM were performed. Water content was analyzed by a halogen moisture analyzer and hair color was measured with a spectrophotometer. Results Hair surfaces tended to become more damaged as the temperature increased. No cortex damage was ever noted, suggesting that the surface of hair might play a role as a barrier to prevent cortex damage. Cell membrane complex was damaged only in the naturally dried group without hair dryer. Moisture content decreased in all treated groups compared to the untreated control group. However, the differences in moisture content among the groups were not statistically significant. Drying under the ambient and 95℃ conditions appeared to change hair color, especially into lightness, after just 10 treatments. Conclusion Although using a hair dryer causes more surface damage than natural drying, using a hair dryer at a distance of 15 cm with continuous motion causes less damage than drying hair naturally. PMID:22148012

Influence of Spore Moisture Content on the Dry-Heat Resistance of Bacillus subtilis var. niger

PubMed Central

Angelotti, Robert; Maryanski, James H.; Butler, Thomas F.; Peeler, James T.; Campbell, Jeptha E.

1968-01-01

The dry-heat resistance of Bacillus subtilis var. niger spores located in or on various materials was determined as D and z values in the range of 105 through 160 C. The systems tested included spores located on steel and paper strips, spores located between stainless-steel washers mated together under 150 inch-lb and 12 inch-lb of torque, and spores encapsulated in methylmethacrylate and epoxy plastics. D values for a given temperature varied with the test system. High D values were observed for the systems in which spores were encapsulated or under heavy torque, whereas lower D values were observed for the steel and paper strip systems and the lightly torqued system. Similar z values were obtained for the plastic and steel strip systems (zD = 21 C), but an unusually low z for spores on paper (zD = 12.9 C) and an unusually high z for spores on steel washers mated at 150 inch-lb of torque (zD = 32 C) were observed. The effect of spore moisture content on the D value of spores encapsulated in water-impermeable plastic was determined, and maximal resistance was observed for spores with a water activity (aw) of 0.2 to 0.4. Significantly decreased D values were observed for spores with moisture contents below aw 0.2 or above aw 0.4. The data indicate that the important factors to be considered when measuring the dry heat resistance of spores are (i) the initial moisture content of the spore, (ii) the rate of spore desiccation during heating, (iii) the water retention capacity of the material in or on which spores are located, and (iv) the relative humidity of the system at the test temperature. Images Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 7 PMID:4968962

Dry co-digestion of sewage sludge and rice straw under mesophilic and thermophilic anaerobic conditions.

PubMed

Chu, Xiangqian; Wu, Guangxue; Wang, Jiaquan; Hu, Zhen-Hu

2015-12-01

Dry anaerobic digestion of sewage sludge can recover biogas as energy; however, its low C/N ratio limits it as a single substrate in the anaerobic digestion. Rice straw is an abundant agricultural residue in China, which is rich in carbon and can be used as carbon source. In the present study, the performance of dry co-digestion of sewage sludge and rice straw was investigated under mesophilic (35 °C) and thermophilic (55 °C) conditions. The operational factors impacting dry co-digestion of sewage sludge and rice straw such as C/N ratio, moisture content, and initial pH were explored under mesophilic conditions. The results show that low C/N ratios resulted in a higher biogas production rate, but a lower specific biogas yield; low moisture content of 65 % resulted in the instability of the digestion system and a low specific biogas yield. Initial pH ranging 7.0-9.0 did not affect the performance of the anaerobic digestion. The C/N ratio of 26-29:1, moisture content of 70-80 %, and pH 7.0-9.0 resulted in good performance in the dry mesophilic co-digestion of sewage sludge and rice straw. As compared with mesophilic digestion, thermophilic co-digestion of sewage sludge and rice straw significantly enhanced the degradation efficiency of the substrates and the specific biogas yield (p < 0.05) at the conditions of C/N ratio 26:1, moisture content 80 %, and natural initial pH. Although high concentrations of ammonia-nitrogen (NH4-N, 1500 mg/kg wet weight) were formed during thermophilic digestion, there was no obvious inhibition occurred. The results indicated that rice straw can be used as carbon source for the dry co-digestion of sewage sludge under mesophilic and thermophilic conditions.

[Effect of irregular bedrock topography on the soil profile pattern of water content in a Karst hillslope.

PubMed

Jia, Jin Tian; Fu, Zhi Yong; Chen, Hong Song; Wang, Ke Lin; Zhou, Wei Jun

2016-06-01

Based on three manually excavated trenches (projection length of 21 m, width of 1 m) along a typical Karst hillslope, the changing trends for soil-bedrock structure, average water content of soil profile and soil-bedrock interface water content along each individual trench were studied. The effect of irregular bedrock topography on soil moisture distribution was discussed. The results showed that the surface topography was inconsistent with the bedrock topography in the Karst hill-slopes. The bedrock topography was highly irregular with a maximum variation coefficient of 82%. The distribution pattern of soil profile of moisture was significantly affected by the underlying undulant bedrock. The soil water content was related to slope position when the fluctuation was gentle, and displayed a linear increase from upslope to downslope. When the bedrock fluctuation increased, the downslope linear increasing trend for soil water content became unapparent, and the spatial continuity of soil moisture was weakened. The soil moisture was converged in rock dents and cracks. The average water content of soil profile was significantly positively correlated with the soil-bedrock interface water content, while the latter responded more sensitively to the bedrock fluctuation.

Application of NIR reflectance spectroscopy on rapid determination of moisture content of wood pellets

USDA-ARS?s Scientific Manuscript database

NIR spectroscopy was used to measure the moisture concentration of wood pellets. Pellets were conditioned to various moisture levels between 0.63and 14.16percent (wet basis) and the moisture concentration was verified using a standard oven method. Samples from the various moisture levels were separa...