30 CFR 75.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Fail safe ground check circuits on high-voltage... High-Voltage Distribution § 75.803 Fail safe ground check circuits on high-voltage resistance grounded... shall include a fail safe ground check circuit to monitor continuously the grounding circuit to assure...

30 CFR 75.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fail safe ground check circuits on high-voltage... High-Voltage Distribution § 75.803 Fail safe ground check circuits on high-voltage resistance grounded... shall include a fail safe ground check circuit to monitor continuously the grounding circuit to assure...

30 CFR 75.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fail safe ground check circuits on high-voltage... High-Voltage Distribution § 75.803 Fail safe ground check circuits on high-voltage resistance grounded... shall include a fail safe ground check circuit to monitor continuously the grounding circuit to assure...

Neural net controlled tag gas sampling system for nuclear reactors

DOEpatents

Gross, Kenneth C.; Laug, Matthew T.; Lambert, John D. B.; Herzog, James P.

1997-01-01

A method and system for providing a tag gas identifier to a nuclear fuel rod and analyze escaped tag gas to identify a particular failed nuclear fuel rod. The method and system include disposing a unique tag gas composition into a plenum of a nuclear fuel rod, monitoring gamma ray activity, analyzing gamma ray signals to assess whether a nuclear fuel rod has failed and is emitting tag gas, activating a tag gas sampling and analysis system upon sensing tag gas emission from a failed nuclear rod and evaluating the escaped tag gas to identify the particular failed nuclear fuel rod.

Active-standby servovalue/actuator development

NASA Technical Reports Server (NTRS)

Masm, R. K.

1973-01-01

A redundant, fail/operate fail/fixed servoactuator was constructed and tested along with electronic models of a servovalve. It was found that a torque motor switch is satisfactory for the space shuttle main engine hydraulic actuation system, and that this system provides an effective failure monitoring technique.

Fail-safe fire detection system

NASA Technical Reports Server (NTRS)

Bloam, E. T.

1974-01-01

Fire detection control system continually monitors its own integrity, automatically signals any malfunction, and separately signals fire in any zone being monitored. Should be of interest in fields of chemical and petroleum processing, power generation, equipment testing, and building protection.

Neural net controlled tag gas sampling system for nuclear reactors

DOEpatents

Gross, K.C.; Laug, M.T.; Lambert, J.B.; Herzog, J.P.

1997-02-11

A method and system are disclosed for providing a tag gas identifier to a nuclear fuel rod and analyze escaped tag gas to identify a particular failed nuclear fuel rod. The method and system include disposing a unique tag gas composition into a plenum of a nuclear fuel rod, monitoring gamma ray activity, analyzing gamma ray signals to assess whether a nuclear fuel rod has failed and is emitting tag gas, activating a tag gas sampling and analysis system upon sensing tag gas emission from a failed nuclear rod and evaluating the escaped tag gas to identify the particular failed nuclear fuel rod. 12 figs.

Diagnostic reasoning techniques for selective monitoring

NASA Technical Reports Server (NTRS)

Homem-De-mello, L. S.; Doyle, R. J.

1991-01-01

An architecture for using diagnostic reasoning techniques in selective monitoring is presented. Given the sensor readings and a model of the physical system, a number of assertions are generated and expressed as Boolean equations. The resulting system of Boolean equations is solved symbolically. Using a priori probabilities of component failure and Bayes' rule, revised probabilities of failure can be computed. These will indicate what components have failed or are the most likely to have failed. This approach is suitable for systems that are well understood and for which the correctness of the assertions can be guaranteed. Also, the system must be such that changes are slow enough to allow the computation.

Diagnostic procedures for Trend Monitoring System (TMS) communications. [coaxial cable bus system

NASA Technical Reports Server (NTRS)

Brown, J. S.; Lenker, M. D.

1979-01-01

A prototype coaxial cable bus communications sytem was developed to support the trend monitoring system (TMS). Troubleshooting procedures are described at the system level. The procedures can be used by repair personnel to isolate a fault in the TMS and to restore the system to operation by swapping out failed components.

In-service communication channel sensing based on reflectometry for TWDM-PON systems

NASA Astrophysics Data System (ADS)

Iida, Daisuke; Kuwano, Shigeru; Terada, Jun

2014-05-01

Many base stations are accommodated in TWDM-PON based mobile backhaul and fronthaul networks for future radio access, and failed connections in an optical network unit (ONU) wavelength channel severely degrade system performance. A cost effective in-service ONU wavelength channel monitor is essential to ensure proper system operation without failed connections. To address this issue we propose a reflectometry-based remote sensing method that provides wavelength channel information with the optical line terminal (OLT)-ONU distance. The method realizes real-time monitoring of ONU wavelength channels without signal quality degradation. Experimental results show it achieves wavelength channel distinction with high distance resolution.

40 CFR 97.632 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.732 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.632 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.732 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.632 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

40 CFR 97.732 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or appendix D to part 75 of this chapter. (b) Audit decertification...

FEDAL SYSTEM OPERATION DURING STATION START-UP. Test Results (T-643734). Core I, Seed 2. Section I

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

An investigation was conducted to determine if any failed blanket fuel elements exist in core locations previously found to have high levels of delayed neutron emitter activity. Data from Fedal System monitors indicate that J5 may have a failed blanket element, there is no evidence of failure at core location F7. (J.R.D.)

40 CFR 97.532 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or appendix E to, part 75 of this chapter...

40 CFR 97.532 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or appendix E to, part 75 of this chapter...

40 CFR 97.532 - Monitoring system out-of-control periods.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Whenever any monitoring system fails to meet the quality-assurance and quality-control requirements or data validation requirements of part 75 of this chapter, data shall be substituted using the applicable missing data procedures in subpart D or subpart H of, or appendix D or appendix E to, part 75 of this chapter...

Electromagnetic Interference of Wireless Local Area Network on Electrocardiogram Monitoring System: A Case Report

PubMed Central

Chung, Seungmin; Yi, Joohee

2013-01-01

Electromagnetic interference (EMI) can affect various medical devices. Herein, we report the case of EMI from wireless local area network (WLAN) on an electrocardiogram (ECG) monitoring system. A patient who had a prior myocardial infarction participated in the cardiac rehabilitation program in the sports medicine center of our hospital under the wireless ECG monitoring system. After WLAN was installed, wireless ECG monitoring system failed to show a proper ECG signal. ECG signal was distorted when WLAN was turned on, but it was normalized after turning off the WLAN. PMID:23613696

40 CFR 141.561 - What happens if my system's turbidity monitoring equipment fails?

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) WATER PROGRAMS (CONTINUED) NATIONAL PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving Fewer Than 10,000 People Individual Filter Turbidity Requirements § 141.561 What...

Autonomous Component Health Management with Failed Component Detection, Identification, and Avoidance

NASA Technical Reports Server (NTRS)

Davis, Robert N.; Polites, Michael E.; Trevino, Luis C.

2004-01-01

This paper details a novel scheme for autonomous component health management (ACHM) with failed actuator detection and failed sensor detection, identification, and avoidance. This new scheme has features that far exceed the performance of systems with triple-redundant sensing and voting, yet requires fewer sensors and could be applied to any system with redundant sensing. Relevant background to the ACHM scheme is provided, and the simulation results for the application of that scheme to a single-axis spacecraft attitude control system with a 3rd order plant and dual-redundant measurement of system states are presented. ACHM fulfills key functions needed by an integrated vehicle health monitoring (IVHM) system. It is: autonomous; adaptive; works in realtime; provides optimal state estimation; identifies failed components; avoids failed components; reconfigures for multiple failures; reconfigures for intermittent failures; works for hard-over, soft, and zero-output failures; and works for both open- and closed-loop systems. The ACHM scheme combines a prefilter that generates preliminary state estimates, detects and identifies failed sensors and actuators, and avoids the use of failed sensors in state estimation with a fixed-gain Kalman filter that generates optimal state estimates and provides model-based state estimates that comprise an integral part of the failure detection logic. The results show that ACHM successfully isolates multiple persistent and intermittent hard-over, soft, and zero-output failures. It is now ready to be tested on a computer model of an actual system.

Contamination of estuaries from failing septic tank systems: difficulties in scaling up from monitored individual systems to cumulative impact.

PubMed

Geary, Phillip; Lucas, Steven

2018-02-03

Aquaculture in many coastal estuaries is threatened by diffuse sources of runoff from different land use activities. The poor performance of septic tank systems (STS), as well as runoff from agriculture, may contribute to the movement of contaminants through ground and surface waters to estuaries resulting in oyster contamination, and following their consumption, impacts to human health. In monitoring individual STS in sensitive locations, it is possible to show that nutrients and faecal contaminants are transported through the subsurface in sandy soils off-site with little attenuation. At the catchment scale however, there are always difficulties in discerning direct linkages between failing STS and water contamination due to processes such as effluent dilution, adsorption, precipitation and vegetative uptake. There is often substantial complexity in detecting and tracing effluent pathways from diffuse sources to water bodies in field studies. While source tracking as well as monitoring using tracers may assist in identifying potential pathways from STS to surface waters and estuaries, there are difficulties in scaling up from monitored individual systems to identify their contribution to the cumulative impact which may be apparent at the catchment scale. The processes which may be obvious through monitoring and dominate at the individual scale may be masked and not readily discernible at the catchment scale due to impacts from other land use activities.

Experience with Multi-Tier Grid MySQL Database Service Resiliency at BNL

NASA Astrophysics Data System (ADS)

Wlodek, Tomasz; Ernst, Michael; Hover, John; Katramatos, Dimitrios; Packard, Jay; Smirnov, Yuri; Yu, Dantong

2011-12-01

We describe the use of F5's BIG-IP smart switch technology (3600 Series and Local Traffic Manager v9.0) to provide load balancing and automatic fail-over to multiple Grid services (GUMS, VOMS) and their associated back-end MySQL databases. This resiliency is introduced in front of the external application servers and also for the back-end database systems, which is what makes it "multi-tier". The combination of solutions chosen to ensure high availability of the services, in particular the database replication and fail-over mechanism, are discussed in detail. The paper explains the design and configuration of the overall system, including virtual servers, machine pools, and health monitors (which govern routing), as well as the master-slave database scheme and fail-over policies and procedures. Pre-deployment planning and stress testing will be outlined. Integration of the systems with our Nagios-based facility monitoring and alerting is also described. And application characteristics of GUMS and VOMS which enable effective clustering will be explained. We then summarize our practical experiences and real-world scenarios resulting from operating a major US Grid center, and assess the applicability of our approach to other Grid services in the future.

Bridge Displacement Monitoring Method Based on Laser Projection-Sensing Technology

PubMed Central

Zhao, Xuefeng; Liu, Hao; Yu, Yan; Xu, Xiaodong; Hu, Weitong; Li, Mingchu; Ou, Jingping

2015-01-01

Bridge displacement is the most basic evaluation index of the health status of a bridge structure. The existing measurement methods for bridge displacement basically fail to realize long-term and real-time dynamic monitoring of bridge structures, because of the low degree of automation and the insufficient precision, causing bottlenecks and restriction. To solve this problem, we proposed a bridge displacement monitoring system based on laser projection-sensing technology. First, the laser spot recognition method was studied. Second, the software for the displacement monitoring system was developed. Finally, a series of experiments using this system were conducted, and the results show that such a system has high measurement accuracy and speed. We aim to develop a low-cost, high-accuracy and long-term monitoring method for bridge displacement based on these preliminary efforts. PMID:25871716

Scalable and fail-safe deployment of the ATLAS Distributed Data Management system Rucio

NASA Astrophysics Data System (ADS)

Lassnig, M.; Vigne, R.; Beermann, T.; Barisits, M.; Garonne, V.; Serfon, C.

2015-12-01

This contribution details the deployment of Rucio, the ATLAS Distributed Data Management system. The main complication is that Rucio interacts with a wide variety of external services, and connects globally distributed data centres under different technological and administrative control, at an unprecedented data volume. It is therefore not possible to create a duplicate instance of Rucio for testing or integration. Every software upgrade or configuration change is thus potentially disruptive and requires fail-safe software and automatic error recovery. Rucio uses a three-layer scaling and mitigation strategy based on quasi-realtime monitoring. This strategy mainly employs independent stateless services, automatic failover, and service migration. The technologies used for deployment and mitigation include OpenStack, Puppet, Graphite, HAProxy and Apache. In this contribution, the interplay between these components, their deployment, software mitigation, and the monitoring strategy are discussed.

A brief overview of channel monitoring in land management: Five case studies. Case study #1

Treesearch

Leslie Reid

1999-01-01

Yesterday we heard about some successful monitoring programs,but today I would like to share some findings from a study I did, which was basically a post-mortem of failed monitoring programs.There were about 30 projects,and I wanted to know why did they fail,and were there patterns of why they failed.The projects ranged from university studies,land management,and...

Structural health monitoring of wind turbine blades

NASA Astrophysics Data System (ADS)

Rumsey, Mark A.; Paquette, Joshua A.

2008-03-01

As electric utility wind turbines increase in size, and correspondingly, increase in initial capital investment cost, there is an increasing need to monitor the health of the structure. Acquiring an early indication of structural or mechanical problems allows operators to better plan for maintenance, possibly operate the machine in a de-rated condition rather than taking the unit off-line, or in the case of an emergency, shut the machine down to avoid further damage. This paper describes several promising structural health monitoring (SHM) techniques that were recently exercised during a fatigue test of a 9 meter glass-epoxy and carbon-epoxy wind turbine blade. The SHM systems were implemented by teams from NASA Kennedy Space Center, Purdue University and Virginia Tech. A commercial off-the-shelf acoustic emission (AE) NDT system gathered blade AE data throughout the test. At a fatigue load cycle rate around 1.2 Hertz, and after more than 4,000,000 fatigue cycles, the blade was diagnostically and visibly failing at the out-board blade spar-cap termination point at 4.5 meters. For safety reasons, the test was stopped just before the blade completely failed. This paper provides an overview of the SHM and NDT system setups and some current test results.

Performance monitor system functional simulator, environmental data, orbiter 101(HFT)

NASA Technical Reports Server (NTRS)

Parker, F. W.

1974-01-01

Information concerning the environment component of the space shuttle performance monitor system simulator (PMSS) and those subsystems operational on the shuttle orbiter 101 used for horizontal flight test (HFT) is provided, along with detailed data for the shuttle performance monitor system (PMS) whose software requirements evolve from three basic PMS functions: (1) fault detection and annunciation; (2) subsystem measurement management; and (3) subsystem configuration management. Information relative to the design and operation of Orbiter systems for HFT is also presented, and the functional paths are identified to the lowest level at which the crew can control the system functions. Measurement requirements are given which are necessary to adequately monitor the health status of the system. PMS process requirements, relative to the measurements which are necessary for fault detection and annunciation of a failed functional path, consist of measurement characteristics, tolerance limits, precondition tests, and correlation measurements.

System Control for the Transitional DCS.

DTIC Science & Technology

1979-07-01

ELEMENT. PROJI Honeywell System and Research Center AREA & WORK UNIT NUMBE Aerospace and Defense Group 2700 Ridgway Parkway, Minneapolis,MN 55413 It1...performance monitoring and stress isolation system for the terrestrial transmission system. The satellite system is assumed to be under the control of its...the routing tables could be in a failed condition while some other route, although less efficient, is still functioning. The recommended adaptive

75 FR 16123 - Dave & Buster’s, Inc.; Analysis of Proposed Consent Order to Aid Public Comment

Federal Register 2010, 2011, 2012, 2013, 2014

2010-03-31

... computer networks or to conduct security investigations, such as by employing an intrusion detection system and monitoring system logs; (b) failed to adequately restrict third-party access to its networks, such... reasonable and appropriate security for personal information on its computer networks. Among other things...

Need for Robust Sensors for Inherently Fail-Safe Gas Turbine Engine Controls, Monitoring, and Prognostics (Postprint)

DTIC Science & Technology

2006-09-01

MONITORING , AND PROGNOSTICS Alireza R. Behbahani Controls / Engine Health Management Turbine Engine Division / PRTS U.S. Air Force Research...Technical Report 2005. 8. Greitzer, Frank et al, “Gas Turbine Engine Health Monitoring and Prognostics ”, International Society of Logistics (SOLE...AFRL-PR-WP-TP-2007-217 NEED FOR ROBUST SENSORS FOR INHERENTLY FAIL-SAFE GAS TURBINE ENGINE CONTROLS, MONITORING , AND PROGNOSTICS (POSTPRINT

When School Management Companies Fail: Righting Educational Wrongs.

ERIC Educational Resources Information Center

Conn, Kathleen

2002-01-01

Reviews public school system of education; describes school management companies (nonprofit, for profit) and their fiduciary duties; discusses monitoring the performance of school management companies; describes legal mechanisms and remedies (tort, contract, agency, and constitutional law) for holding school management companies accountable.…

Bioretention Monitoring: Designing Rain Gardens to Promote Nitrate Removal

EPA Science Inventory

Laboratory and field-scale studies of bioretention systems have often shown these structures to have a high capacity for removal of suspended solids, heavy metals, and phosphorus. Most studies, however, failed to demonstrate the same success in removing nitrate. Typical rain ga...

Using Surveillance Camera Systems to Monitor Public Domains: Can Abuse Be Prevented

DTIC Science & Technology

2006-03-01

relationship with a 16-year old girl failed. The incident was captured by a New York City Police Department surveillance camera. Although the image...administrators stated that the images recorded were “…nothing more than images of a few bras and panties .”17 The use of CCTV surveillance systems for

DOE Program on Seismic Characterization for Regions of Interest to CTBT Monitoring,

DTIC Science & Technology

1995-08-14

processing of the monitoring network data). While developing and testing the corrections and other parameters needed by the automated processing systems...the secondary network. Parameters tabulated in the knowledge base must be appropriate for routine automated processing of network data, and must also...operation of the PNDC, as well as to results of investigations of "special events" (i.e., those events that fail to locate or discriminate during automated

The design and implementation of on-line monitoring system for UHV compact shunt capacitors

NASA Astrophysics Data System (ADS)

Tao, Weiliang; Ni, Xuefeng; Lin, Hao; Jiang, Shengbao

2017-08-01

Because of the large capacity and compact structure of the UHV compact shunt capacitor, it is difficult to take effective measures to detect and prevent the faults. If the fault capacitor fails to take timely maintenance, it will pose a threat to the safe operation of the system and the life safety of the maintenance personnel. The development of UHV compact shunt capacitor on-line monitoring system can detect and record the on-line operation information of UHV compact shunt capacitors, analyze and evaluate the early fault warning signs, find out the fault capacitor or the capacitor with fault symptom, to ensure safe and reliable operation of the system.

Non-compliance with the International Code of Marketing of Breast Milk Substitutes is not confined to the infant formula industry.

PubMed

Forsyth, Stewart

2013-06-01

Infant feeding policy and practice continues to be a contentious area of global health care. The infant formula industry is widely considered to be the bête noire with frequent claims that they adopt marketing and sales practices that are not compliant with the WHO Code. However, failure to resolve these issues over three decades suggests that there may be wider systemic failings. Review of published papers, commentaries and reports relating to the implementation and governance of the WHO Code with specific reference to issues of non-compliance. The analysis set out in this paper indicates that there are systemic failings at all levels of the implementation and monitoring process including the failure of WHO to successfully 'urge' governments to implement the Code in its entirety; a lack of political will by Member States to implement and monitor the Code and a lack of formal and transparent governance structures. Non-compliance with the WHO Code is not confined to the infant formula industry and several actions are identified, including the need to address issues of partnership working and the establishment of governance systems that are robust, independent and transparent.

50 CFR 300.117 - Prohibitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... (9) Fail to use real-time C-VMS port-to-port on board U.S. vessels harvesting AMLR in the Convention... documentation of the use of real-time C-VMS port-to-port by the vessel that harvested such Dissostichus species... fish, from sorting the catch to the storage of the finished product. (bb) Vessel monitoring systems. (1...

Promoting health and reducing costs: a role for reform of self-monitoring of blood glucose provision within the National Health Service.

PubMed

Leigh, S; Idris, I; Collins, B; Granby, P; Noble, M; Parker, M

2016-05-01

To determine the cost-effectiveness of all options for the self-monitoring of blood glucose funded by the National Health Service, providing guidance for disinvestment and testing the hypothesis that advanced meter features may justify higher prices. Using data from the Health and Social Care Information Centre concerning all 8 340 700 self-monitoring of blood glucose-related prescriptions during 2013/2014, we conducted a cost-minimization analysis, considering both strip and lancet costs, including all clinically equivalent technologies for self-monitoring of blood glucose, as determined by the ability to meet ISO-15197:2013 guidelines for meter accuracy. A total of 56 glucose monitor, test strip and lancet combinations were identified, of which 38 met the required accuracy standards. Of these, the mean (range) net ingredient costs for test strips and lancets were £0.27 (£0.14-£0.32) and £0.04 (£0.02-£0.05), respectively, resulting in a weighted average of £0.28 (£0.18-£0.37) per test. Systems providing four or more advanced features were priced equal to those providing just one feature. A total of £12 m was invested in providing 42 million self-monitoring of blood glucose tests with systems that fail to meet acceptable accuracy standards, and efficiency savings of £23.2 m per annum are achievable if the National Health Service were to disinvest from technologies providing lesser functionality than available alternatives, but at a much higher price. The study uncovered considerable variation in the price paid by the National Health Service for self-monitoring of blood glucose, which could not be explained by the availability of advanced meter features. A standardized approach to self-monitoring of blood glucose prescribing could achieve significant efficiency savings for the National Health Service, whilst increasing overall utilisation and improving safety for those currently using systems that fail to meet acceptable standards for measurement accuracy. © 2015 Diabetes UK.

A wireless monitoring system for Hydrocephalus shunts.

PubMed

Narayanaswamy, A; Nourani, M; Tamil, L; Bianco, S

2015-08-01

Patients with Hydrocephalus are usually treated by diverting the excess Cerebrospinal Fluid (CSF) to other parts of the body using shunts. More than 40 percentage of shunts implanted fail within the first two years. Obstruction in the shunts is one of the major causes of failure (45 percent) and the detection of obstruction reduces the complexity of the revision surgery. This paper describes a proposed wireless monitoring system for clog detection and flow measurement in shunts. A prototype was built using multiple pressure sensors along the shunt catheters for sensing the location of clog and flow rate. Regular monitoring of flow rates can be used to adjust the valve in the shunt to prevent over drainage or under drainage of CSF. The accuracy of the flow measurement is more than 90 percent.

Monitoring Active Volcanoes

NASA Astrophysics Data System (ADS)

Swanson, Don

Monitoring volcanoes is a surprisingly controversial enterprise. Some volcanologists argue that monitoring promises too much and delivers too little for risk mitigation. They trust only strict land-use measures (and accompanying high insurance premiums in risky zones) and urge that funds be used for public education and awareness rather than for instrumental monitoring. Others claim that monitoring is more akin to Brownian motion than to science: lots of action but little net progress. Still other volcanologists acknowledge the potential value of monitoring for prediction and warning but despair at the difficulty of it all. And, finally, some shy from surveillance, fearing the legal consequences of a failed monitoring effort during these litigious times. They wonder, “Will I be sued if an eruption is not foreseen or if an instrument fails at a critical time?”

Robust Online Monitoring for Calibration Assessment of Transmitters and Instrumentation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramuhalli, Pradeep; Coble, Jamie B.; Shumaker, Brent

Robust online monitoring (OLM) technologies are expected to enable the extension or elimination of periodic sensor calibration intervals in operating and new reactors. These advances in OLM technologies will improve the safety and reliability of current and planned nuclear power systems through improved accuracy and increased reliability of sensors used to monitor key parameters. In this article, we discuss an overview of research being performed within the Nuclear Energy Enabling Technologies (NEET)/Advanced Sensors and Instrumentation (ASI) program, for the development of OLM algorithms to use sensor outputs and, in combination with other available information, 1) determine whether one or moremore » sensors are out of calibration or failing and 2) replace a failing sensor with reliable, accurate sensor outputs. Algorithm development is focused on the following OLM functions: • Signal validation • Virtual sensing • Sensor response-time assessment These algorithms incorporate, at their base, a Gaussian Process-based uncertainty quantification (UQ) method. Various plant models (using kernel regression, GP, or hierarchical models) may be used to predict sensor responses under various plant conditions. These predicted responses can then be applied in fault detection (sensor output and response time) and in computing the correct value (virtual sensing) of a failing physical sensor. The methods being evaluated in this work can compute confidence levels along with the predicted sensor responses, and as a result, may have the potential for compensating for sensor drift in real-time (online recalibration). Evaluation was conducted using data from multiple sources (laboratory flow loops and plant data). Ongoing research in this project is focused on further evaluation of the algorithms, optimization for accuracy and computational efficiency, and integration into a suite of tools for robust OLM that are applicable to monitoring sensor calibration state in nuclear power plants.« less

Analysis of Alerting System Failures in Commercial Aviation Accidents

NASA Technical Reports Server (NTRS)

Mumaw, Randall J.

2017-01-01

The role of an alerting system is to make the system operator (e.g., pilot) aware of an impending hazard or unsafe state so the hazard can be avoided or managed successfully. A review of 46 commercial aviation accidents (between 1998 and 2014) revealed that, in the vast majority of events, either the hazard was not alerted or relevant hazard alerting occurred but failed to aid the flight crew sufficiently. For this set of events, alerting system failures were placed in one of five phases: Detection, Understanding, Action Selection, Prioritization, and Execution. This study also reviewed the evolution of alerting system schemes in commercial aviation, which revealed naive assumptions about pilot reliability in monitoring flight path parameters; specifically, pilot monitoring was assumed to be more effective than it actually is. Examples are provided of the types of alerting system failures that have occurred, and recommendations are provided for alerting system improvements.

Fault tolerant features and experiments of ANTS distributed real-time system

NASA Astrophysics Data System (ADS)

Dominic-Savio, Patrick; Lo, Jien-Chung; Tufts, Donald W.

1995-01-01

The ANTS project at the University of Rhode Island introduces the concept of Active Nodal Task Seeking (ANTS) as a way to efficiently design and implement dependable, high-performance, distributed computing. This paper presents the fault tolerant design features that have been incorporated in the ANTS experimental system implementation. The results of performance evaluations and fault injection experiments are reported. The fault-tolerant version of ANTS categorizes all computing nodes into three groups. They are: the up-and-running green group, the self-diagnosing yellow group and the failed red group. Each available computing node will be placed in the yellow group periodically for a routine diagnosis. In addition, for long-life missions, ANTS uses a monitoring scheme to identify faulty computing nodes. In this monitoring scheme, the communication pattern of each computing node is monitored by two other nodes.

Award ER25750: Coordinated Infrastructure for Fault Tolerance Systems Indiana University Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lumsdaine, Andrew

2013-03-08

The main purpose of the Coordinated Infrastructure for Fault Tolerance in Systems initiative has been to conduct research with a goal of providing end-to-end fault tolerance on a systemwide basis for applications and other system software. While fault tolerance has been an integral part of most high-performance computing (HPC) system software developed over the past decade, it has been treated mostly as a collection of isolated stovepipes. Visibility and response to faults has typically been limited to the particular hardware and software subsystems in which they are initially observed. Little fault information is shared across subsystems, allowing little flexibility ormore » control on a system-wide basis, making it practically impossible to provide cohesive end-to-end fault tolerance in support of scientific applications. As an example, consider faults such as communication link failures that can be seen by a network library but are not directly visible to the job scheduler, or consider faults related to node failures that can be detected by system monitoring software but are not inherently visible to the resource manager. If information about such faults could be shared by the network libraries or monitoring software, then other system software, such as a resource manager or job scheduler, could ensure that failed nodes or failed network links were excluded from further job allocations and that further diagnosis could be performed. As a founding member and one of the lead developers of the Open MPI project, our efforts over the course of this project have been focused on making Open MPI more robust to failures by supporting various fault tolerance techniques, and using fault information exchange and coordination between MPI and the HPC system software stack from the application, numeric libraries, and programming language runtime to other common system components such as jobs schedulers, resource managers, and monitoring tools.« less

Microbial water quality before and after the repair of a failing onsite wastewater treatment system adjacent to coastal waters

USGS Publications Warehouse

Conn, K.E.; Habteselassie, M.Y.; Denene, Blackwood A.; Noble, R.T.

2012-01-01

Aims: The objective was to assess the impacts of repairing a failing onsite wastewater treatment system (OWTS, i.e., septic system) as related to coastal microbial water quality. Methods and Results: Wastewater, groundwater and surface water were monitored for environmental parameters, faecal indicator bacteria (total coliforms, Escherichia coli, enterococci) and the viral tracer MS2 before and after repairing a failing OWTS. MS2 results using plaque enumeration and quantitative reverse transcriptase polymerase chain reaction (qRT-PCR) often agreed, but inhibition limited the qRT-PCR assay sensitivity. Prerepair, MS2 persisted in groundwater and was detected in the nearby creek; postrepair, it was not detected. In groundwater, total coliform concentrations were lower and E.??coli was not detected, while enterococci concentrations were similar to prerepair levels. E.??coli and enterococci surface water concentrations were elevated both before and after the repair. Conclusions: Repairing the failing OWTS improved groundwater microbial water quality, although persistence of bacteria in surface water suggests that the OWTS was not the singular faecal contributor to adjacent coastal waters. A suite of tracers is needed to fully assess OWTS performance in treating microbial contaminants and related impacts on receiving waters. Molecular methods like qRT-PCR have potential but require optimization. Significance and Impact of Study: This is the first before and after study of a failing OWTS and provides guidance on selection of microbial tracers and methods. ?? 2011 The Authors. Journal of Applied Microbiology ?? 2011 The Society for Applied Microbiology.

Fault Detection and Safety in Closed-Loop Artificial Pancreas Systems

PubMed Central

2014-01-01

Continuous subcutaneous insulin infusion pumps and continuous glucose monitors enable individuals with type 1 diabetes to achieve tighter blood glucose control and are critical components in a closed-loop artificial pancreas. Insulin infusion sets can fail and continuous glucose monitor sensor signals can suffer from a variety of anomalies, including signal dropout and pressure-induced sensor attenuations. In addition to hardware-based failures, software and human-induced errors can cause safety-related problems. Techniques for fault detection, safety analyses, and remote monitoring techniques that have been applied in other industries and applications, such as chemical process plants and commercial aircraft, are discussed and placed in the context of a closed-loop artificial pancreas. PMID:25049365

Implementing a Microcontroller Watchdog with a Field-Programmable Gate Array (FPGA)

NASA Technical Reports Server (NTRS)

Straka, Bartholomew

2013-01-01

Reliability is crucial to safety. Redundancy of important system components greatly enhances reliability and hence safety. Field-Programmable Gate Arrays (FPGAs) are useful for monitoring systems and handling the logic necessary to keep them running with minimal interruption when individual components fail. A complete microcontroller watchdog with logic for failure handling can be implemented in a hardware description language (HDL.). HDL-based designs are vendor-independent and can be used on many FPGAs with low overhead.

A program of correlated observations using the EGRET instrument on GRO and the IMB neutrino detector

NASA Technical Reports Server (NTRS)

Svoboda, Robert C.

1992-01-01

A reliable, real-time supernova monitoring system was devised using the IMB neutrino detector to serve as an 'early-warning' system for EGRET and other instruments on GRO. New methods and software were developed to allow the IMB monitoring computer in Cleveland to: recognize that a trigger burst had occurred; make a judgement on whether the burst was spurrious or an actual supernova; prepare brief summary files and 'quick-look' data so that a final disposition could be made by a trained scientist; and contact the 'watch' scientist via personal beeper in Baton Rouge. This system ran from Dec. 1990 to Apr. 1991, when the neutrino detector failed for unrelated reasons. In addition to the supernova system, high-energy neutrino data was prepared and formatted for comparison with EGRET gamma-ray data.

40 CFR 141.810 - Violations.

Code of Federal Regulations, 2013 CFR

2013-07-01

... has an E. coli-positive sample in any monitoring period (routine and repeat samples are used in this... fails to comply with the reporting and recordkeeping requirements of this subpart. (e) It fails to...

40 CFR 141.810 - Violations.

Code of Federal Regulations, 2012 CFR

2012-07-01

... has an E. coli-positive sample in any monitoring period (routine and repeat samples are used in this... fails to comply with the reporting and recordkeeping requirements of this subpart. (e) It fails to...

40 CFR 141.810 - Violations.

Code of Federal Regulations, 2014 CFR

2014-07-01

... has an E. coli-positive sample in any monitoring period (routine and repeat samples are used in this... fails to comply with the reporting and recordkeeping requirements of this subpart. (e) It fails to...

40 CFR 141.810 - Violations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... has an E. coli-positive sample in any monitoring period (routine and repeat samples are used in this... fails to comply with the reporting and recordkeeping requirements of this subpart. (e) It fails to...

40 CFR 141.810 - Violations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... has an E. coli-positive sample in any monitoring period (routine and repeat samples are used in this... fails to comply with the reporting and recordkeeping requirements of this subpart. (e) It fails to...

Checklists and Monitoring in the Cockpit: Why Crucial Defenses Sometimes Fail

NASA Technical Reports Server (NTRS)

Dismukes, R. Key; Berman, Ben

2010-01-01

Checklists and monitoring are two essential defenses against equipment failures and pilot errors. Problems with checklist use and pilots failures to monitor adequately have a long history in aviation accidents. This study was conducted to explore why checklists and monitoring sometimes fail to catch errors and equipment malfunctions as intended. Flight crew procedures were observed from the cockpit jumpseat during normal airline operations in order to: 1) collect data on monitoring and checklist use in cockpit operations in typical flight conditions; 2) provide a plausible cognitive account of why deviations from formal checklist and monitoring procedures sometimes occur; 3) lay a foundation for identifying ways to reduce vulnerability to inadvertent checklist and monitoring errors; 4) compare checklist and monitoring execution in normal flights with performance issues uncovered in accident investigations; and 5) suggest ways to improve the effectiveness of checklists and monitoring. Cognitive explanations for deviations from prescribed procedures are provided, along with suggestions for countermeasures for vulnerability to error.

Data Auditor: Analyzing Data Quality Using Pattern Tableaux

NASA Astrophysics Data System (ADS)

Srivastava, Divesh

Monitoring databases maintain configuration and measurement tables about computer systems, such as networks and computing clusters, and serve important business functions, such as troubleshooting customer problems, analyzing equipment failures, planning system upgrades, etc. These databases are prone to many data quality issues: configuration tables may be incorrect due to data entry errors, while measurement tables may be affected by incorrect, missing, duplicate and delayed polls. We describe Data Auditor, a tool for analyzing data quality and exploring data semantics of monitoring databases. Given a user-supplied constraint, such as a boolean predicate expected to be satisfied by every tuple, a functional dependency, or an inclusion dependency, Data Auditor computes "pattern tableaux", which are concise summaries of subsets of the data that satisfy or fail the constraint. We discuss the architecture of Data Auditor, including the supported types of constraints and the tableau generation mechanism. We also show the utility of our approach on an operational network monitoring database.

Ubiquitous health monitoring and real-time cardiac arrhythmias detection: a case study.

PubMed

Li, Jian; Zhou, Haiying; Zuo, Decheng; Hou, Kun-Mean; De Vaulx, Christophe

2014-01-01

As the symptoms and signs of heart diseases that cause sudden cardiac death, cardiac arrhythmia has attracted great attention. Due to limitations in time and space, traditional approaches to cardiac arrhythmias detection fail to provide a real-time continuous monitoring and testing service applicable in different environmental conditions. Integrated with the latest technologies in ECG (electrocardiograph) analysis and medical care, the pervasive computing technology makes possible the ubiquitous cardiac care services, and thus brings about new technical challenges, especially in the formation of cardiac care architecture and realization of the real-time automatic ECG detection algorithm dedicated to care devices. In this paper, a ubiquitous cardiac care prototype system is presented with its architecture framework well elaborated. This prototype system has been tested and evaluated in all the clinical-/home-/outdoor-care modes with a satisfactory performance in providing real-time continuous cardiac arrhythmias monitoring service unlimitedly adaptable in time and space.

Radar monitoring of oil pollution

NASA Technical Reports Server (NTRS)

Guinard, N. W.

1970-01-01

Radar is currently used for detecting and monitoring oil slicks on the sea surface. The four-frequency radar system is used to acquire synthetic aperature imagery of the sea surface on which the oil slicks appear as a nonreflecting area on the surface surrounded by the usual sea return. The value of this technique was demonstrated, when the four-frequency radar system was used to image the oil spill of tanker which has wrecked. Imagery was acquired on both linear polarization (horizontal, vertical) for frequencies of 428, 1228, and 8910 megahertz. Vertical returns strongly indicated the presence of oil while horizontal returns failed to detect the slicks. Such a result is characteristic of the return from the sea and cannot presently be interpreted as characteristics of oil spills. Because an airborne imaging radar is capable of providing a wide-swath coverage under almost all weather conditions, it offers promise in the development of a pollution-monitoring system that can provide a coastal watch for oil slicks.

40 CFR 58.60 - Federal monitoring.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 5 2010-07-01 2010-07-01 false Federal monitoring. 58.60 Section 58.60... QUALITY SURVEILLANCE Federal Monitoring § 58.60 Federal monitoring. The Administrator may locate and operate an ambient air monitoring site if the State or local agency fails to locate, or schedule to be...

Quiet Clean Short-haul Experimental Engine (QCSEE) over-the-wing control system design report

NASA Technical Reports Server (NTRS)

1977-01-01

A control system incorporating a digital electronic control was designed for the over-the-wing engine. The digital electronic control serves as the primary controlling element for engine fuel flow and core compressor stator position. It also includes data monitoring capability, a unique failure indication and corrective action feature, and optional provisions for operating with a new type of servovalve designed to operate in response to a digital-type signal and to fail with its output device hydraulically locked into position.

Evaluating the Use of Tissue Oximetry to Decrease Intensive Unit Monitoring for Free Flap Breast Reconstruction.

PubMed

Ricci, Joseph A; Vargas, Christina R; Ho, Olivia A; Lin, Samuel J; Tobias, Adam M; Lee, Bernard T

2017-07-01

Postoperative free flap care has historically required intensive monitoring for 24 hours in an intensive care unit. Continuous monitoring with tissue oximetry has allowed earlier detection of vascular compromise, decreasing flap loss and improving salvage. This study aims to identify whether a fast-track postoperative paradigm can be safely used with tissue oximetry to decrease intensive monitoring and costs. All consecutive microsurgical breast reconstructions performed at a single institution were reviewed (2008-2014) and cases requiring return to the operating room were identified. Data evaluated included patient demographics, the take back time course, and complications of flap loss and salvage. A cost-benefit analysis was performed to analyse the utility of a postoperative intensive monitoring setting. There were 900 flaps performed and 32 required an unplanned return to the operating room. There were 16 flaps that required a reexploration within the first 24 hours; the standard length of intensive unit monitoring. After 4 hours, there were 7 flaps (44%) detected by tissue oximetry for reexploration. After 15 hours of intensive monitoring postoperatively, cost analysis revealed that the majority (15/16; 94%) of failing flaps had been identified and the cost of identifying each subsequent failing flap exceeded the cost of another hour of intensive monitoring. The postoperative paradigm for microsurgical flaps has historically required intensive unit monitoring. Using tissue oximetry, a fast-track pathway can reduce time spent in an intensive monitoring setting from 24 to 15 hours with significant cost savings and minimal risk of missing a failing free flap.

Back-Analyses of Landfill Instability Induced by High Water Level: Case Study of Shenzhen Landfill

PubMed Central

Peng, Ren; Hou, Yujing; Zhan, Liangtong; Yao, Yangping

2016-01-01

In June 2008, the Shenzhen landfill slope failed. This case is used as an example to study the deformation characteristics and failure mode of a slope induced by high water levels. An integrated monitoring system, including water level gauges, electronic total stations, and inclinometers, was used to monitor the slope failure process. The field measurements suggest that the landfill landslide was caused by a deep slip along the weak interface of the composite liner system at the base of the landfill. The high water level is considered to be the main factor that caused this failure. To calculate the relative interface shear displacements in the geosynthetic multilayer liner system, a series of numerical direct shear tests were carried out. Based on the numerical results, the composite lining system simplified and the centrifuge modeling technique was used to quantitatively evaluate the effect of water levels on landfill instability. PMID:26771627

4D monitoring of actively failing rockslopes

NASA Astrophysics Data System (ADS)

Rosser, Nick; Williams, Jack; Hardy, Richard; Brain, Matthew

2017-04-01

Assessing the conditions which promote rockfall to collapse relies upon detailed monitoring, ideally before, during and immediately after failure. With standard repeat surveys it is common that surveys do not coincide with or capture precursors, or that surveys are widely spaced relative to the timing and duration of driving forces such as storms. As a result gaining insight into the controls on failure and the timescales over which precursors operate remains difficult to establish with certainty, and establishing direct links between environmental conditions and rock-falls, or sequences of events prior to rockfall, remain difficult to define. To address this, we present analysis of a high-frequency 3D laser scan dataset captured using a new permanently installed system developed to constantly monitor actively failing rock slopes. The system is based around a time of flight laser scanner, integrated with and remotely controlled by dedicated controls and analysis software. The system is configured to capture data at 0.1 m spacing across > 22,000 m3 at up to 30 minute intervals. Here we present results captured with this system over a period of 9 months, spanning spring to winter 2015. Our analysis is focussed upon improving the understanding of the nature of small (< 1m^3) rockfalls falling from near vertical rock cliffs. We focus here on the development of a set of algorithms for differencing that trade-off the temporal resolution of frequent surveys (hourly) against high spatial resolution point clouds (< 0.05 m) to enhance the precision of change detection, allowing both deformation and detachments to be monitored through time. From this dataset we derive rockfall volume frequency distributions based upon short-interval surveys, and identify the presence and/or absence of precursors, in what we believe to be the first constant volumetric measurement of rock face erosion. The results hold implications for understanding of rockfall mechanics, but also for how actively eroding surfaces can be monitored at high temporal frequency. Whilst high frequency data is ideal for describing processes that evolve rapidly through time, the cumulative errors that accumulate when monitored changes are dominated by inverse power-law distributed volumes are significant. To conclude we consider the benefits of defining survey frequency on the basis of the changes being detected relative to the accumulation of errors that inevitably arises when comparing high numbers of sequential surveys.

Lindenmayer DB and Likens GE (eds): Effective ecological monitoring [book review

Treesearch

Charles T. Scott

2011-01-01

Long-term ecological monitoring is becoming increasingly important but more challenging to fund. Lindenmayer and Likens describe the common characteristics of successful monitoring programs and of those that fail. They draw upon their monitoring experiences together, independently, and from a variety of other long-term monitoring programs around the world. They then...

Improving Insider Threat Training Awareness and Mitigation Programs at Nuclear Facilities.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abbott, Shannon

In recent years, insider threat programs have become an important aspect of nuclear security, and nuclear security training courses. However, many nuclear security insider threat programs fail to address the insider threat attack and monitoring potential that exists on information technology (IT) systems. This failure is critical because of the importance of information technology and networks in today’s world. IT systems offer an opportunity to perpetrate dangerous insider attacks, but they also present an opportunity to monitor for them and prevent them. This paper suggests a number of best practices for monitoring and preventing insider attacks on IT systems, andmore » proposes the development of a new IT insider threat tabletop that can be used to help train nuclear security practitioners on how best to implement IT insider threat prevention best practices. The development of IT insider threat best practices and a practical tabletop exercise will allow nuclear security practitioners to improve nuclear security trainings as it integrates a critical part of insider threat prevention into the broader nuclear security system.« less

Validation of the ROSSMAX blood pressure measuring monitor according to the European Society of Hypertension International Protocol for Validation of Blood Pressure Measuring Devices in Adults.

PubMed

O'Brien, Eoin; Atkins, Neil; Murphy, Anne; Lyons, Simon

2003-12-01

It is now accepted that blood pressure measuring devices should be subjected to an independent evaluation of their accuracy before they are marketed for clinical use. The results of validation of the ROSSMAX Blood Pressure Measuring Monitor for self-measurement according to the European Society of Hypertension International Protocol for Validation of Blood Pressure Measuring Devices in Adults are presented in this paper. Thirty-three subjects were recruited from among staff and patients at Beaumont Hospital, Dublin, Ireland. The ROSSMAX monitor was connected to the Sphygmocorder, an audiovisual system for validation, which records blood pressure on tape and video for later analysis. Nine sequential same-arm measurements between the device and a standard mercury sphygmomanometer were recorded using the Sphygmocorder. In phase 1, the ROSSMAX monitor produced 21 measurements within 5 mmHg, 31 within 10 mmHg and 38 within 15 mmHg for systolic blood pressure (SBP), and 36 within 5 mmHg, 43 within 10 mmHg and 45 within 15 mmHg for diastolic blood pressure (DBP). The mean differences were -5.6 (10.2) [mean (SD)] mmHg for SBP and -0.5 (4.5) mmHg for DBP. The ROSSMAX monitor failed to meet any of the criteria for SBP but comfortably passed all of the criteria for DBP. In phase 2.1, the ROSSMAX monitor had 51 measurements within 5 mmHg, 73 within 10 mmHg and 86 within 15 mmHg for SBP, and 71 measurements within 5 mmHg, 93 within 10 mmHg and 98 within 15 mmHg for DBP. The mean differences were -4.5. (9.5) mmHg for SBP and -1.8 (5.0) mmHg for DBP. The ROSSMAX monitor failed to meet any of the criteria for SBP but comfortably passed all of the criteria for DBP. In phase 2.2, 16 subjects had at least two of the differences lying within 5 mmHg and 10 subjects had no differences within 5 mmHg for SBP; 26 subjects had at least two of the differences falling within 5 mmHg and three subjects no differences within 5 mmHg for DBP. The ROSSMAX monitor failed to meet the criteria for SBP but passed the criteria for DBP. The ROSSMAX monitor cannot be recommended for clinical use in an adult population because it records SBP inaccurately.

The Next Generation of Interoperability Agents in Healthcare

PubMed Central

Cardoso, Luciana; Marins, Fernando; Portela, Filipe; Santos, Manuel ; Abelha, António; Machado, José

2014-01-01

Interoperability in health information systems is increasingly a requirement rather than an option. Standards and technologies, such as multi-agent systems, have proven to be powerful tools in interoperability issues. In the last few years, the authors have worked on developing the Agency for Integration, Diffusion and Archive of Medical Information (AIDA), which is an intelligent, agent-based platform to ensure interoperability in healthcare units. It is increasingly important to ensure the high availability and reliability of systems. The functions provided by the systems that treat interoperability cannot fail. This paper shows the importance of monitoring and controlling intelligent agents as a tool to anticipate problems in health information systems. The interaction between humans and agents through an interface that allows the user to create new agents easily and to monitor their activities in real time is also an important feature, as health systems evolve by adopting more features and solving new problems. A module was installed in Centro Hospitalar do Porto, increasing the functionality and the overall usability of AIDA. PMID:24840351

Clutter isolation and cardiac monitoring using harmonic doppler radar with heterodyne receiver and passive RF tags.

PubMed

Singh, Aditya; Lubecke, Victor

2010-01-01

A harmonic radar employing the use of harmonic passive RF tags can be successfully used to isolate the human respiration from environmental clutter. This paper describes the successful use of heterodyne receiver architecture with Doppler radar to track the heart-rate of a human being using passive body-worn harmonic tags in presence of a controlled noise generator at distances up to 120 cm. The heterodyne system results have been compared with those of a conventional Doppler radar for cardiopulmonary monitoring that fails to isolate the noise from heart-rate in presence of a noise source.

Noise test system of rotating machinery in nuclear power station based on microphone array

NASA Astrophysics Data System (ADS)

Chang, Xincai; Guan, Jishi; Qi, Liangcai

2017-12-01

Rotating machinery plays an important role in all walks of life. Once the equipment fails, equipment maintenance and shutdown will cause great social harm and economic losses. Equipment safety operations at nuclear power stations have always been of top priority. It is prone to noise when the equipment is out of order or aging. Failure to find or develop equipment at the initial stage of equipment failure or ageing will pose a serious threat to the safety of the plant’s equipment. In this paper, sound imaging diagnosis technology is applied as a supplementary method to the condition monitoring and diagnosis system of rotating machinery in nuclear power stations. It provides a powerful guarantee for the condition monitoring and fault diagnosis of rotating machinery in nuclear power stations.

Evaluation of Blood Glucose Monitoring System in Screening for Neonatal Hypoglycemia: Tighter Accuracy Standard.

PubMed

Tsao, Mei-Fen; Chang, Hui-Wen; Chang, Chien-Hsi; Cheng, Chi-Hsuan; Lin, Hsiu-Chen

2017-05-01

Neonatal hypoglycemia may cause severe neurological damages; therefore, tight glycemic control is crucial to identify neonate at risk. Previous blood glucose monitoring system (BGMS) failed to perform well in neonates; there are calls for the tightening of accuracy requirements. It remains a need for accurate BGMS for effective bedside diabetes management in neonatal care within a hospital population. A total of 300 neonates were recruited from local hospitals. Accuracy performance of a commercially available BGMS was evaluated against reference instrument in screening for neonatal hypoglycemia, and assessment was made based on the ISO15197:2013 and a tighter standard. At blood glucose level < 47 mg/dl, BGMS assessed met the minimal accuracy requirement of ISO 15197:2013 and tighter standard at 100% and 97.2%, respectively.

Quality control of inkjet technology for DNA microarray fabrication.

PubMed

Pierik, Anke; Dijksman, Frits; Raaijmakers, Adrie; Wismans, Ton; Stapert, Henk

2008-12-01

A robust manufacturing process is essential to make high-quality DNA microarrays, especially for use in diagnostic tests. We investigated different failure modes of the inkjet printing process used to manufacture low-density microarrays. A single nozzle inkjet spotter was provided with two optical imaging systems, monitoring in real time the flight path of every droplet. If a droplet emission failure is detected, the printing process is automatically stopped. We analyzed over 1.3 million droplets. This information was used to investigate the performance of the inkjet system and to obtain detailed insight into the frequency and causes of jetting failures. Of all the substrates investigated, 96.2% were produced without any system or jetting failures. In 1.6% of the substrates, droplet emission failed and was correctly identified. Appropriate measures could then be taken to get the process back on track. In 2.2%, the imaging systems failed while droplet emission occurred correctly. In 0.1% of the substrates, droplet emission failure that was not timely detected occurred. Thus, the overall yield of the microarray manufacturing process was 99.9%, which is highly acceptable for prototyping.

Smart fiber-reinforced polymer anchorage system with optical fiber Bragg grating sensors

NASA Astrophysics Data System (ADS)

Huang, Minghua; Zhou, Zhi; He, Jianping; Chen, Genda; Ou, Jinping

2010-03-01

Civil Engineers have used fiber reinforced polymer (FRP) with high axial strength as an effective and economical alternative to steel in harsh corrosion environments. However, the practical applications of FRP are limited by the tendency of FRP materials to fail suddenly under lateral pressure and surface injury. For example, shear stresses result from the bonding effect between the FRP material and the structure of the anchorage system due to the lower shear strength of FRP. This paper proposes a novel smart FRP anchorage system with embedded optical fiber Bragg grating (FBG) sensors to monitor the axial strain state and accordingly the interfacial shear stress, as well as the interfacial damage characteristics of FRP anchorage. One FBG sensor was embedded in an FRP rod outside the anchorage region to evaluate the properties of the material, and seven FBG sensors were distributed along the rod in the anchor to monitor the axial strain variations and study the interfacial mechanical behaviors of the smart FRP anchorage under a static pulling load. The experimental results agreed well with theoretical predictions. The smart FRP anchorage system with optical FBG sensors proves effective and practical for monitoring the long-term mechanical behavior of FRP anchorage systems.

Monitoring conservation success in a large oak woodland landscape

Treesearch

Rich Reiner; Emma Underwood; John-O Niles

2002-01-01

Monitoring is essential in understanding the success or failure of a conservation project and provides the information needed to conduct adaptive management. Although there is a large body of literature on monitoring design, it fails to provide sufficient information to practitioners on how to organize and apply monitoring when implementing landscape-scale conservation...

The Preferences of Students for Particular Monitors in a PSI Course

ERIC Educational Resources Information Center

Neves, Luis Pimenta; Romiszowski, Alexander J.

1976-01-01

The study examines whether there is any relationship between the popularity of a given monitor and his leniency. It was found that students tend to choose the more lenient monitor, but if they are failed by a given monitor, they tend to go back to him for re-assessment. (Author)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruuge, A; Erdi, Y; Mahmood, U

Purpose: The conformance of Primary Diagnostic Monitors (PDMs) to the DICOM GSDF is increasingly required by several state and city regulators. Our purpose was to quantitatively characterize the luminance performance of the internal, built in photometer of BARCO monitors against an externally calibrated luminance meter. Methods: Thirty one PDMs (BARCO) were included in our analysis. An externally calibrated photometer (RaySafe Solo Light) was used to measure the luminance and illuminance values. Measured monitors were located at various hospital sites, radiology physicians’ offices and radiology reading rooms. All measured PDMs were equipped with the manufacturer’s built-in photometers and connected to Barcomore » MediCal QA web service for manual and automatic quality control measurements. PDM combinations included 1, 2 and 4 monitors depending on the location. TG-18 and SMPTE test patterns were used to evaluate monitor performance. Results: All the PDMs exceeded the luminance ratio of 250:1, as required by NYC PDM guidelines. One PDM failed the NYC requirement for the minimal luminance level of 350 cd/m2. As compared to the external photometer, the difference in measurement of the maximum luminance with the built-in photometer was found to exceed 5% on 6 of the PDM measured, with a maximum deviation of 10%. The age of the monitors that failed was on average 5 years. All monitors passed the luminance uniformity test, which was 30% from the center of the monitor to the 4 corner locations. Four PDMs failed the Gray Scale Display Function (GSDF) calibration. Conclusion: For the consistent display of medical images and continued conformance with the DICOM GSDF standard, it is essential to compare the performance of the built-in photometer with an externally calibrated photometer for monitors that are older than 5 years.« less

Blunt splenic injuries: have we watched long enough?

PubMed

Smith, Jason; Armen, Scott; Cook, Charles H; Martin, Larry C

2008-03-01

Nonoperative management (NOM) of blunt splenic injuries (BSIs) has been used with increasing frequency in adult patients. There are currently no definitive guidelines established for how long BSI patients should be monitored for failure of NOM after injury. This study was performed to ascertain the length of inpatient observation needed to capture most failures, and to identify factors associated with failure of NOM. We utilized the National Trauma Data Bank to determine time to failure after BSI. During the 5-year study period, 23,532 patients were identified with BSI, of which 2,366 (10% overall) were taken directly to surgery (within 2 hours of arrival). Of 21,166 patients initially managed nonoperatively, 18,506 were successful (79% of all-comers). Patients with isolated BSI are currently monitored approximately 5 days as inpatients. Of patients failing NOM, 95% failed during the first 72 hours, and monitoring 2 additional days saw only 1.5% more failures. Factors influencing success of NOM included computed tomographic injury grade, severity of patient injury, and American College of Surgeons designation of trauma center. Importantly, patients who failed NOM did not seem to have detrimental outcomes when compared with patients with successful NOM. No statistically significant predictive variables could be identified that would help predict patients who would go on to fail NOM. We conclude that at least 80% of BSI can be managed successfully with NOM, and that patients should be monitored as inpatients for failure after BSI for 3 to 5 days.

Alarms Philosophy

DOE Office of Scientific and Technical Information (OSTI.GOV)

White, Karen S; Kasemir, Kay

2009-01-01

An effective alarm system consists of a mechanism to monitor control points and generate alarm notifications, tools for operators to view, hear, acknowledge and handle alarms and a good configuration. Despite the availability of numerous fully featured tools, accelerator alarm systems continue to be disappointing to operations, frequently to the point of alarms being permanently silenced or totally ignored. This is often due to configurations that produce an excessive number of alarms or fail to communicate the required operator response. Most accelerator controls systems do a good job of monitoring specified points and generating notifications when parameters exceed predefined limits.more » In some cases, improved tools can help, but more often, poor configuration is the root cause of ineffective alarm systems. A SNS, we have invested considerable effort in generating appropriate configurations using a rigorous set of rules based on best practices in the industrial process controls community. This paper will discuss our alarm configuration philosophy and operator response to our new system.« less

Triplexer Monitor Design for Failure Detection in FTTH System

NASA Astrophysics Data System (ADS)

Fu, Minglei; Le, Zichun; Hu, Jinhua; Fei, Xia

2012-09-01

Triplexer was one of the key components in FTTH systems, which employed an analog overlay channel for video broadcasting in addition to bidirectional digital transmission. To enhance the survivability of triplexer as well as the robustness of FTTH system, a multi-ports device named triplexer monitor was designed and realized, by which failures at triplexer ports can be detected and localized. Triplexer monitor was composed of integrated circuits and its four input ports were connected with the beam splitter whose power division ratio was 95∶5. By means of detecting the sampled optical signal from the beam splitters, triplexer monitor tracked the status of the four ports in triplexer (e.g. 1310 nm, 1490 nm, 1550 nm and com ports). In this paper, the operation scenario of the triplexer monitor with external optical devices was addressed. And the integrated circuit structure of the triplexer monitor was also given. Furthermore, a failure localization algorithm was proposed, which based on the state transition diagram. In order to measure the failure detection and localization time under the circumstance of different failed ports, an experimental test-bed was built. Experiment results showed that the detection time for the failure at 1310 nm port by the triplexer monitor was less than 8.20 ms. For the failure at 1490 nm or 1550 nm port it was less than 8.20 ms and for the failure at com port it was less than 7.20 ms.

Failure Analysis and Magnetic Evaluation of Tertiary Superheater Tube Used in Gas-Fired Boiler

NASA Astrophysics Data System (ADS)

Mohapatra, J. N.; Patil, Sujay; Sah, Rameshwar; Krishna, P. C.; Eswarappa, B.

2018-02-01

Failure analysis was carried out on a prematurely failed tertiary superheater tube used in gas-fired boiler. The analysis includes a comparative study of visual examination, chemical composition, hardness and microstructure at failed region, adjacent and far to failure as well as on fresh tube. The chemistry was found matching to the standard specification, whereas the hardness was low in failed tube compared to the fish mouth opening region and the fresh tube. Microscopic examination of failed sample revealed the presence of spheroidal carbides of Cr and Mo predominantly along the grain boundaries. The primary cause of failure is found to be localized heating. Magnetic hysteresis loop (MHL) measurements were carried out to correlate the magnetic parameters with microstructure and mechanical properties to establish a possible non-destructive evaluation (NDE) for health monitoring of the tubes. The coercivity of the MHL showed a very good correlation with microstructure and mechanical properties deterioration enabling a possible NDE technique for the health monitoring of the tubes.

Global situational awareness and early warning of high-consequence climate change.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Backus, George A.; Carr, Martin J.; Boslough, Mark Bruce Elrick

2009-08-01

Global monitoring systems that have high spatial and temporal resolution, with long observational baselines, are needed to provide situational awareness of the Earth's climate system. Continuous monitoring is required for early warning of high-consequence climate change and to help anticipate and minimize the threat. Global climate has changed abruptly in the past and will almost certainly do so again, even in the absence of anthropogenic interference. It is possible that the Earth's climate could change dramatically and suddenly within a few years. An unexpected loss of climate stability would be equivalent to the failure of an engineered system on amore » grand scale, and would affect billions of people by causing agricultural, economic, and environmental collapses that would cascade throughout the world. The probability of such an abrupt change happening in the near future may be small, but it is nonzero. Because the consequences would be catastrophic, we argue that the problem should be treated with science-informed engineering conservatism, which focuses on various ways a system can fail and emphasizes inspection and early detection. Such an approach will require high-fidelity continuous global monitoring, informed by scientific modeling.« less

Situation management in the Link Monitor and Control Operator Assistant (LMCOA)

NASA Technical Reports Server (NTRS)

Hill, Randall W., Jr.; Lee, Lorrine F.

1993-01-01

This paper describes a knowledge-based system called the Situation Manager that was developed for the Link Monitor and Control Operator Assistant (LMCOA) at the Jet Propulsion Laboratory. This system was developed in response to a number of deficiencies that were identified in an earlier version of the LMCOA: the need to close the control loop between sending a directive and knowing when its execution is complete (versus just closing the communications loop), the need to recognize an anomaly and alert the operator when a directive is rejected or a link device fails, and the need to suggest ways to work around an anomaly, provided that it is recognizable. In response to these needs, the Situation Manager has been designed to provide the LMCOA with three basic capabilities: situation assessment, anomaly diagnosis, and recovery from commonly occurring problems.

Automated Testing Experience of the Linear Aerospike SR-71 Experiment (LASRE) Controller

NASA Technical Reports Server (NTRS)

Larson, Richard R.

1999-01-01

System controllers must be fail-safe, low cost, flexible to software changes, able to output health and status words, and permit rapid retest qualification. The system controller designed and tested for the aerospike engine program was an attempt to meet these requirements. This paper describes (1) the aerospike controller design, (2) the automated simulation testing techniques, and (3) the real time monitoring data visualization structure. Controller cost was minimized by design of a single-string system that used an off-the-shelf 486 central processing unit (CPU). A linked-list architecture, with states (nodes) defined in a user-friendly state table, accomplished software changes to the controller. Proven to be fail-safe, this system reported the abort cause and automatically reverted to a safe condition for any first failure. A real time simulation and test system automated the software checkout and retest requirements. A program requirement to decode all abort causes in real time during all ground and flight tests assured the safety of flight decisions and the proper execution of mission rules. The design also included health and status words, and provided a real time analysis interpretation for all health and status data.

Applicability of a Crack-Detection System for Use in Rotor Disk Spin Test Experiments Being Evaluated

NASA Technical Reports Server (NTRS)

Abdul-Aziz, Ali; Baaklini, George Y.; Roth, Don J.

2004-01-01

Engine makers and aviation safety government institutions continue to have a strong interest in monitoring the health of rotating components in aircraft engines to improve safety and to lower maintenance costs. To prevent catastrophic failure (burst) of the engine, they use nondestructive evaluation (NDE) and major overhauls for periodic inspections to discover any cracks that might have formed. The lowest cost fluorescent penetrant inspection NDE technique can fail to disclose cracks that are tightly closed during rest or that are below the surface. The NDE eddy current system is more effective at detecting both crack types, but it requires careful setup and operation and only a small portion of the disk can be practically inspected. So that sensor systems can sustain normal function in a severe environment, health-monitoring systems require the sensor system to transmit a signal if a crack detected in the component is above a predetermined length (but below the length that would lead to failure) and lastly to act neutrally upon the overall performance of the engine system and not interfere with engine maintenance operations. Therefore, more reliable diagnostic tools and high-level techniques for detecting damage and monitoring the health of rotating components are very essential in maintaining engine safety and reliability and in assessing life.

Implantable hemodynamic monitoring (the Chronicle IHM system): remote telemonitoring for patients with heart failure.

PubMed

Ho, C

2008-01-01

(1) Remote monitoring for ambulatory heart failure patients uses an implantable device to record hemodynamic data and transmit it to a central server for continuous assessment. (2) Preliminary evidence from observational studies suggests a potential for reducing hospitalizations with the use of right ventricle implantable hemodynamic monitoring (IHM). However, although a multicentre, randomized controlled trial (COMPASS-HF) showed a reduction in hospitalizations in the IHM group the results were not statistically significant and the US Food and Drug Administration panel concluded the trial failed to meet its primary efficacy endpoint. (3) In the COMPASS-HF study the most common device-related complication was lead dislodgement. (4) Large randomized controlled trials are needed to demonstrate the clinical utility of IHM, particularly in terms of its impact on reducing hospitalization and improving patient outcomes.

Design of a Geothermal Downhole Magnetic Flowmeter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Glowka, Dave A.; Normann, Randy A.

2015-06-15

This paper covers the development of a 300°C geothermal solid-state magnetic flowmeter (or magmeter) to support in situ monitoring of future EGS (enhanced geothermal system) production wells. Existing flowmeters are simple mechanical spinner sensors. These mechanical sensors fail within as little as 10 hrs, while a solid-state magmeter has the potential for months/years of operation. The design and testing of a magnetic flow sensor for use with existing high-temperature electronics is presented.

A Variational Assimilation System for Nearshore Wave Modeling

DTIC Science & Technology

2013-05-01

shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number ...5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 6. AUTHOR(S) 7...PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) 10

Combining Modeling and Monitoring to Produce a New Paradigm of an Integrated Approach to Providing Long-Term Control of Contaminants

NASA Astrophysics Data System (ADS)

Fogwell, T. W.

2009-12-01

Sir David King, Chief Science Advisor to the British government and Cambridge University Professor, stated in October 2005, "The scientific community is considerably more capable than it has been in the past to assist governments to avoid and reduce risk to their own populations. Prime ministers and presidents ignore the advice from the science community at the peril of their own populations." Some of these greater capabilities can be found in better monitoring techniques applied to better modeling methods. These modeling methods can be combined with the information derived from monitoring data in order to decrease the risk of population exposure to dangerous substances and to promote efficient control or cleanup of the contaminants. An introduction is presented of the types of problems that exist for long-term control of radionuclides at DOE sites. A breakdown of the distributions at specific sites is given, together with the associated difficulties. A paradigm for remediation showing the integration of monitoring with modeling is presented. It is based on a feedback system that allows for the monitoring to act as principal sensors in a control system. The resulting system can be optimized to improve performance. Optimizing monitoring automatically entails linking the monitoring with modeling. If monitoring designs were required to be more efficient, thus requiring optimization, then the monitoring automatically becomes linked to modeling. Records of decision could be written to accommodate revisions in monitoring as better modeling evolves. Currently the establishment of a very prescriptive monitoring program fails to have a mechanism for improving models and improving control of the contaminants. The technical pieces of the required paradigm are already available; they just need to be implemented and applied to solve the long-term control of the contaminants. An integration of the various parts of the system is presented. Each part is described, and examples are given. References are given to other projects which bring together similar elements in systems for the control of contaminants. Trends are given for the development of the technical features of a robust system. Examples of monitoring methods for specific sites are given. The examples are used to illustrate how such a system would work. Examples of technology needs are presented. Finally, other examples of integrated modeling-monitoring approaches are presented.

SafeNet: a methodology for integrating general-purpose unsafe devices in safe-robot rehabilitation systems.

PubMed

Vicentini, Federico; Pedrocchi, Nicola; Malosio, Matteo; Molinari Tosatti, Lorenzo

2014-09-01

Robot-assisted neurorehabilitation often involves networked systems of sensors ("sensory rooms") and powerful devices in physical interaction with weak users. Safety is unquestionably a primary concern. Some lightweight robot platforms and devices designed on purpose include safety properties using redundant sensors or intrinsic safety design (e.g. compliance and backdrivability, limited exchange of energy). Nonetheless, the entire "sensory room" shall be required to be fail-safe and safely monitored as a system at large. Yet, sensor capabilities and control algorithms used in functional therapies require, in general, frequent updates or re-configurations, making a safety-grade release of such devices hardly sustainable in cost-effectiveness and development time. As such, promising integrated platforms for human-in-the-loop therapies could not find clinical application and manufacturing support because of lacking in the maintenance of global fail-safe properties. Under the general context of cross-machinery safety standards, the paper presents a methodology called SafeNet for helping in extending the safety rate of Human Robot Interaction (HRI) systems using unsafe components, including sensors and controllers. SafeNet considers, in fact, the robotic system as a device at large and applies the principles of functional safety (as in ISO 13489-1) through a set of architectural procedures and implementation rules. The enabled capability of monitoring a network of unsafe devices through redundant computational nodes, allows the usage of any custom sensors and algorithms, usually planned and assembled at therapy planning-time rather than at platform design-time. A case study is presented with an actual implementation of the proposed methodology. A specific architectural solution is applied to an example of robot-assisted upper-limb rehabilitation with online motion tracking. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

A blood pressure monitor with robust noise reduction system under linear cuff inflation and deflation.

PubMed

Usuda, Takashi; Kobayashi, Naoki; Takeda, Sunao; Kotake, Yoshifumi

2010-01-01

We have developed the non-invasive blood pressure monitor which can measure the blood pressure quickly and robustly. This monitor combines two measurement mode: the linear inflation and the linear deflation. On the inflation mode, we realized a faster measurement with rapid inflation rate. On the deflation mode, we realized a robust noise reduction. When there is neither noise nor arrhythmia, the inflation mode incorporated on this monitor provides precise, quick and comfortable measurement. Once the inflation mode fails to calculate appropriate blood pressure due to body movement or arrhythmia, then the monitor switches automatically to the deflation mode and measure blood pressure by using digital signal processing as wavelet analysis, filter bank, filter combined with FFT and Inverse FFT. The inflation mode succeeded 2440 measurements out of 3099 measurements (79%) in an operating room and a rehabilitation room. The new designed blood pressure monitor provides the fastest measurement for patient with normal circulation and robust measurement for patients with body movement or severe arrhythmia. Also this fast measurement method provides comfortableness for patients.

Endoscopic ultrasound-guided choledochoduodenostomy after a failed or impossible ERCP.

PubMed

Mora Soler, Ana María; Álvarez Delgado, Alberto; Piñero Pérez, María Concepción; Velasco-Guardado, Antonio; Marcos Prieto, Héctor; Rodríguez Pérez, Antonio

2018-05-01

endoscopic ultrasound-guided biliary drainage (EUS-BD) is an alternative to percutaneous trans-hepatic biliary drainage (PTBD) in cases of failed endoscopic retrograde cholangiopancreatography (ERCP). this is a retrospective description of six cases of endoscopic ultrasound-guided biliary drainage via choledochoduodenostomy (EUCD), as well as the clinical characteristics, endoscopic procedure, complications and monitoring. all cases had malignant distal biliary obstruction. The procedure was concluded with good drainage in four out of six patients. Two late complications were recorded that were caused by stent migration and there were no deaths related with the procedure. The average monitoring period was six months. EUCD can be considered as a valid therapeutic choice in some selected cases and when performed by a team of expert endoscopists in cases of failed ERCP drainage or as an alternative to PTBD. However, the procedure has some associated complications.

Pilots' monitoring strategies and performance on automated flight decks: an empirical study combining behavioral and eye-tracking data.

PubMed

Sarter, Nadine B; Mumaw, Randall J; Wickens, Christopher D

2007-06-01

The objective of the study was to examine pilots' automation monitoring strategies and performance on highly automated commercial flight decks. A considerable body of research and operational experience has documented breakdowns in pilot-automation coordination on modern flight decks. These breakdowns are often considered symptoms of monitoring failures even though, to date, only limited and mostly anecdotal data exist concerning pilots' monitoring strategies and performance. Twenty experienced B-747-400 airline pilots flew a 1-hr scenario involving challenging automation-related events on a full-mission simulator. Behavioral, mental model, and eye-tracking data were collected. The findings from this study confirm that pilots monitor basic flight parameters to a much greater extent than visual indications of the automation configuration. More specifically, they frequently fail to verify manual mode selections or notice automatic mode changes. In other cases, they do not process mode annunciations in sufficient depth to understand their implications for aircraft behavior. Low system observability and gaps in pilots' understanding of complex automation modes were shown to contribute to these problems. Our findings describe and explain shortcomings in pilot's automation monitoring strategies and performance based on converging behavioral, eye-tracking, and mental model data. They confirm that monitoring failures are one major contributor to breakdowns in pilot-automation interaction. The findings from this research can inform the design of improved training programs and automation interfaces that support more effective system monitoring.

Acoustic emission monitoring of low velocity impact damage in graphite/epoxy laminates during tensile loading

NASA Technical Reports Server (NTRS)

Parker, Bradford H.

1992-01-01

An acoustic emission (AE) system was set up in a linear location data acquisition mode to monitor the tensile loading of eight-ply quasi-isotropic graphite/epoxy specimens containing low velocity impact damage. The impact damage was induced using an instrumented drop weight tower. During impact, specimens were supported by either an aluminum plate or a membrane configuration. Cross-sectional examinations revealed that the aluminum plate configuration resulted in primarily matrix cracking and back surface fiber failure. The membrane support resulted in only matrix cracking and delamination damage. Penetrant enhanced radiography and immersion ultrasonics were used in order to assess the amount of impact damage in each tensile specimen. During tensile loading, AE reliably detected and located the damage sites which included fiber failure. All specimens with areas of fiber breakage ultimately failed at the impact site. AE did not reliably locate damage which consisted of only delaminations and matrix cracking. Specimens with this type of damage did not ultimately fail at the impact site. In summary, AE demonstrated the ability to increase the reliability of structural proof tests; however, the successful use of this technique requires extensive baseline testing.

The search for failed supernovae with the Large Binocular Telescope: constraints from 7 yr of data

NASA Astrophysics Data System (ADS)

Adams, S. M.; Kochanek, C. S.; Gerke, J. R.; Stanek, K. Z.

2017-08-01

We report updated results for the first 7 yr of our programme to monitor 27 galaxies within 10 Mpc using the Large Binocular Telescope to search for failed supernovae (SNe) - core collapses of massive stars that form black holes without luminous SNe. In the new data, we identify no new compelling candidates and confirm the existing candidate. Given the six successful core-collapse SNe in the sample and one likely failed SN, the implied fraction of core collapses that result in failed SNe is f=0.14^{+0.33}_{-0.10} at 90 per cent confidence. If the current candidate is a failed SN, the fraction of failed SN naturally explains the missing high-mass red supergiants SN progenitors and the black hole mass function. If the current candidate is ultimately rejected, the data imply a 90 per cent confidence upper limit on the failed SN fraction of f < 0.35.

SleepSense: A Noncontact and Cost-Effective Sleep Monitoring System.

PubMed

Lin, Feng; Zhuang, Yan; Song, Chen; Wang, Aosen; Li, Yiran; Gu, Changzhan; Li, Changzhi; Xu, Wenyao

2017-02-01

Quality of sleep is an important indicator of health and well being. Recent developments in the field of in-home sleep monitoring have the potential to enhance a person's sleeping experience and contribute to an overall sense of well being. Existing in-home sleep monitoring devices either fail to provide adequate sleep information or are obtrusive to use. To overcome these obstacles, a noncontact and cost-effective sleep monitoring system, named SleepSense, is proposed for continuous recognition of the sleep status, including on-bed movement, bed exit, and breathing section. SleepSense consists of three parts: a Doppler radar-based sensor, a robust automated radar demodulation module, and a sleep status recognition framework. Herein, several time-domain and frequency-domain features are extracted for the sleep recognition framework. A prototype of SleepSense is presented and evaluated using two sets of experiments. In the short-term controlled experiment, the SleepSense achieves an overall 95.1% accuracy rate in identifying various sleep status. In the 75-minute sleep study, SleepSense demonstrates wide usability in real life. The error rate for breathing rate extraction in this study is only 6.65%. These experimental results indicate that SleepSense is an effective and promising solution for in-home sleep monitoring.

On-line detection of key radionuclides for fuel-rod failure in a pressurized water reactor.

PubMed

Qin, Guoxiu; Chen, Xilin; Guo, Xiaoqing; Ni, Ning

2016-08-01

For early on-line detection of fuel rod failure, the key radionuclides useful in monitoring must leak easily from failing rods. Yield, half-life, and mass share of fission products that enter the primary coolant also need to be considered in on-line analyses. From all the nuclides that enter the primary coolant during fuel-rod failure, (135)Xe and (88)Kr were ultimately chosen as crucial for on-line monitoring of fuel-rod failure. A monitoring system for fuel-rod failure detection for pressurized water reactor (PWR) based on the LaBr3(Ce) detector was assembled and tested. The samples of coolant from the PWR were measured using the system as well as a HPGe γ-ray spectrometer. A comparison showed the method was feasible. Finally, the γ-ray spectra of primary coolant were measured under normal operations and during fuel-rod failure. The two peaks of (135)Xe (249.8keV) and (88)Kr (2392.1keV) were visible, confirming that the method is capable of monitoring fuel-rod failure on-line. Copyright © 2016 Elsevier Ltd. All rights reserved.

Compositional Trends in Acid Fluids of Copahue Volcano, Argentina: Evidence for a failed eruption in 2004?

NASA Astrophysics Data System (ADS)

Kading, T. J.; Brophy, M.; Varekamp, J. C.

2008-12-01

The concentrations and fluxes of major, minor, and trace elements in the crater lake, volcanic spring, and acidified watershed of Copahue Volcano, Neuquen province, Argentina, have been monitored over the last decade. The 2000 Copahue eruption resulted in enhanced S/Cl, increased concentrations and fluxes of rock forming elements (especially Mg and Na) with strongly raised Mg/Cl and Mg/K values. The degree of LREE enrichment decreased and a pronounced Eu anomaly developed in the fluids (Eu/Eu*> rock values). These patterns are explained as the result of hot acid fluid attack on newly intruded magma, with early dissolution of olivine (Mg spike) and plagioclase (Na spike, Eu anomaly). Similar compositional changes were observed in water samples taken in November, 2004, but no eruption occurred. These may be the signals of a small magmatic intrusion into the hydrothermal system, which failed to continue into an eruption. The compositional changes of Copahue volcanic fluids over the last decade will be discussed in the context of chemical signals of an actual and a suspected 'failed eruption'.

Subsurface Treatment of Domestic Wastewater Using Single Domicile Constructed Wetlands

NASA Astrophysics Data System (ADS)

Aseltyne, T.; Steer, D.; Fraser, L.

2001-05-01

Analysis of one year of input versus output water quality monitoring data from nine household wastewater treatment wetlands in western Ohio indicates that these systems substantially reduce effluent loads delivered to the local watershed. Overall performance as measured by output water quality improvement varies widely between the nine systems despite their close proximity and identical design. These three-cell systems (septic tank with 2 subsurface wetland cells) are found to reduce biological oxygen demand (BOD) 70-98%, fecal coliform 60-99.9%, NH3 29-97%, Phosphorus 21-99.9% and total suspended solids (TSS) up to 97%. NO3/NO2 readings were only taken at the second wetland cell, but show that NO3/NO2 levels are at 0.005-5.01 mg/l and well below the USEPA standards for discharge from a wetland. On average, the pH of the wastewater increases from 6.6 at the septic tank to 8.7 at the wetland output. Nearly all the monitoring data indicate clear decreases in nutrient loads and bacteria though individual systems are found to non-systematically fail to meet EPA discharge guidelines for one or more of the monitored loads. Preliminary analysis of the data indicates a decrease in overall efficiency of the wetlands in April that may be related to seasonal factors. These systems will be monitored for the next three years in order to relate changing performance trends to seasonal variability.

Remote Monitoring of Cathodic Protection and Cathodic Protection System Upgrades for Tanks and Pipelines at Fort Carson

DTIC Science & Technology

2007-06-01

HOISTS, CRANES AND DERRICKS ο ο Cables and sheaves regularly inspected ο ο Slings and chains, hooks and eyes inspected before each use ο ο Equipment...osion from soil corrosion, bacterial corrosion, and stress corrosion cracking. • Cathodic protection is applicable over a wide range of e...should be flat against the material. Bent rivets will fail under stress . Especially note condition of Dee Ring rivets and Dee Ring metal wear pads

Inertial/GPS Integrated Geolocation System for Detection and Recovery of Buried Munitions

DTIC Science & Technology

2011-07-01

notwithstanding any other provision of law , no person shall be subject to a penalty for failing to comply with a collection of information if it does not...ELEMENT NUMBER 6. AUTHOR( S ) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) Ohio State...University,154 W 12th Avenue,Columbus,OH,43210 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME( S ) AND ADDRESS(ES) 10

A comprehensive infectious disease management system.

PubMed

Marcu, Alex; Farley, John D

2009-01-01

An efficient electronic management system is now an essential tool for the successful management and monitoring of those affected by communicable infectious diseases (Human Immunodeficiency Virus - HIV, hepatitis C - HEP C) during the course of the treatment. The current methods which depend heavily on manual collecting, compiling and disseminating treatment information are labor-intensive and time consuming. Clinics specialized in the treatment of infectious diseases use a mix of electronic systems that fail to interact with each other, result in data duplication, and do not support treatment of the patient as a whole. The purpose of the Infectious Disease Management System is to reduce the administrative overhead associated with data collection and analysis while providing correlation abilities and decision support in accordance with defined treatment guidelines. This Infectious Disease Management System was developed to: Ensure cost effectiveness by means of low software licensing costs, Introduce a centralized mechanism of collecting and monitoring all infectious disease management data, Automate electronic retrieval of laboratory findings, Introduce a decision support mechanism as per treatment guidelines, Seamlessly integrate of application modules, Provide comprehensive reporting capabilities, Maintain a high level of user friendliness.

Upgrading the Digital Electronics of the PEP-II Bunch Current Monitors at the Stanford Linear Accelerator Center

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kline, Josh; /SLAC

2006-08-28

The testing of the upgrade prototype for the bunch current monitors (BCMs) in the PEP-II storage rings at the Stanford Linear Accelerator Center (SLAC) is the topic of this paper. Bunch current monitors are used to measure the charge in the electron/positron bunches traveling in particle storage rings. The BCMs in the PEP-II storage rings need to be upgraded because components of the current system have failed and are known to be failure prone with age, and several of the integrated chips are no longer produced making repairs difficult if not impossible. The main upgrade is replacing twelve old (1995)more » field programmable gate arrays (FPGAs) with a single Virtex II FPGA. The prototype was tested using computer synthesis tools, a commercial signal generator, and a fast pulse generator.« less

Reaping the space investment. [Shuttle era geosynchronous satellite based technological trends

NASA Technical Reports Server (NTRS)

Calio, A. J.

1979-01-01

By 1999 operational space systems will be implemented routinely on a worldwide scale in many areas vital to human survival and life quality. Geosynchronous-based monitoring and observation will be extensively used. The Shuttle era will bring in the capability to allow monitoring and identifying pollution sources which fail to stay within required limits. Remotely sensed data over land masses will provide needed facts on renewable and nonrenewable earth resources. New instruments and techniques will have been developed to provide geologists with clues to the declining number of deposits of fuels and minerals. Also, practical methods for predicting earthquakes will have been elaborated by 1999. Communications will see implementation of many of the technological goals of 1978.

ROBUST ONLINE MONITORING FOR CALIBRATION ASSESSMENT OF TRANSMITTERS AND INSTRUMENTATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramuhalli, Pradeep; Tipireddy, Ramakrishna; Lerchen, Megan E.

Robust online monitoring (OLM) technologies are expected to enable the extension or elimination of periodic sensor calibration intervals in operating and new reactors. Specifically, the next generation of OLM technology is expected to include newly developed advanced algorithms that improve monitoring of sensor/system performance and enable the use of plant data to derive information that currently cannot be measured. These advances in OLM technologies will improve the safety and reliability of current and planned nuclear power systems through improved accuracy and increased reliability of sensors used to monitor key parameters. In this paper, we discuss an overview of research beingmore » performed within the Nuclear Energy Enabling Technologies (NEET)/Advanced Sensors and Instrumentation (ASI) program, for the development of OLM algorithms to use sensor outputs and, in combination with other available information, 1) determine whether one or more sensors are out of calibration or failing and 2) replace a failing sensor with reliable, accurate sensor outputs. Algorithm development is focused on the following OLM functions: • Signal validation – fault detection and selection of acceptance criteria • Virtual sensing – signal value prediction and acceptance criteria • Response-time assessment – fault detection and acceptance criteria selection A GP-based uncertainty quantification (UQ) method previously developed for UQ in OLM, was adapted for use in sensor-fault detection and virtual sensing. For signal validation, the various components to the OLM residual (which is computed using an AAKR model) were explicitly defined and modeled using a GP. Evaluation was conducted using flow loop data from multiple sources. Results using experimental data from laboratory-scale flow loops indicate that the approach, while capable of detecting sensor drift, may be incapable of discriminating between sensor drift and model inadequacy. This may be due to a simplification applied in the initial modeling, where the sensor degradation is assumed to be stationary. In the case of virtual sensors, the GP model was used in a predictive mode to estimate the correct sensor reading for sensors that may have failed. Results have indicated the viability of using this approach for virtual sensing. However, the GP model has proven to be computationally expensive, and so alternative algorithms for virtual sensing are being evaluated. Finally, automated approaches to performing noise analysis for extracting sensor response time were developed. Evaluation of this technique using laboratory-scale data indicates that it compares well with manual techniques previously used for noise analysis. Moreover, the automated and manual approaches for noise analysis also compare well with the current “gold standard”, hydraulic ramp testing, for response time monitoring. Ongoing research in this project is focused on further evaluation of the algorithms, optimization for accuracy and computational efficiency, and integration into a suite of tools for robust OLM that are applicable to monitoring sensor calibration state in nuclear power plants.« less

The Impact of a Monitoring Scheme on Engagement in an Online Course

ERIC Educational Resources Information Center

Burke, Grainne; Mac an Bhaird, Ciaran; O'Shea, Ann

2012-01-01

In the National University of Ireland Maynooth, in-coming first-year mathematics students are given a diagnostic test. The purpose of this test is to measure their basic knowledge and manipulation skills in mathematics. Those who fail this test are deemed at risk of failing their mathematics modules and are enrolled in a supplementary online…

Sample Acquisition and Analytical Chemistry Challenges to Verifying Compliance to Aviators Breathing Oxygen (ABO) Purity Specification

NASA Technical Reports Server (NTRS)

Graf, John

2015-01-01

NASA has been developing and testing two different types of oxygen separation systems. One type of oxygen separation system uses pressure swing technology, the other type uses a solid electrolyte electrochemical oxygen separation cell. Both development systems have been subjected to long term testing, and performance testing under a variety of environmental and operational conditions. Testing these two systems revealed that measuring the product purity of oxygen, and determining if an oxygen separation device meets Aviator's Breathing Oxygen (ABO) specifications is a subtle and sometimes difficult analytical chemistry job. Verifying product purity of cryogenically produced oxygen presents a different set of analytical chemistry challenges. This presentation will describe some of the sample acquisition and analytical chemistry challenges presented by verifying oxygen produced by an oxygen separator - and verifying oxygen produced by cryogenic separation processes. The primary contaminant that causes gas samples to fail to meet ABO requirements is water. The maximum amount of water vapor allowed is 7 ppmv. The principal challenge of verifying oxygen produced by an oxygen separator is that it is produced relatively slowly, and at comparatively low temperatures. A short term failure that occurs for just a few minutes in the course of a 1 week run could cause an entire tank to be rejected. Continuous monitoring of oxygen purity and water vapor could identify problems as soon as they occur. Long term oxygen separator tests were instrumented with an oxygen analyzer and with an hygrometer: a GE Moisture Monitor Series 35. This hygrometer uses an aluminum oxide sensor. The user's manual does not report this, but long term exposure to pure oxygen causes the aluminum oxide sensor head to bias dry. Oxygen product that exceeded the 7 ppm specification was improperly accepted, because the sensor had biased. The bias is permanent - exposure to air does not cause the sensor to return to its original response - but the bias can be accounted for by recalibrating the sensor. After this issue was found, continuous measurements of water vapor in the oxygen product were made using an FTIR. The FTIR cell is relatively large, so response time is slow - but moisture measurements were repeatable and accurate. Verifying ABO compliance for oxygen produced by commercial cryogenic processes has a different set of sample acquisition and analytical chemistry challenges. Customers want analytical chemists to conserve as much as possible. Hygrometers are not exposed to hours of continuous flow of oxygen, so they don't bias, but small amounts of contamination in valves can cause a "fail". K bottles are periodically cleaned and recertified - after cleaning residual moisture can cause a "fail". Operators let bottle pressure drop to room pressure, introduce outside air into the bottle, and the subsequent fill will "fail". Outside storage of K-bottles has allowed enough in-leakage, so contents will "fail".

78 FR 42723 - Airworthiness Directives; Pilatus Aircraft Ltd. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-17

... System (ESIS). If the common ground fails both navigations systems could fail simultaneously, which could... Display (PFD) and the Electronic Standby Instrument System (ESIS). If the common ground fails both navigations systems could fail simultaneously, which could result in loss of control. We are issuing this...

Monitoring System for the GRID Monte Carlo Mass Production in the H1 Experiment at DESY

NASA Astrophysics Data System (ADS)

Bystritskaya, Elena; Fomenko, Alexander; Gogitidze, Nelly; Lobodzinski, Bogdan

2014-06-01

The H1 Virtual Organization (VO), as one of the small VOs, employs most components of the EMI or gLite Middleware. In this framework, a monitoring system is designed for the H1 Experiment to identify and recognize within the GRID the best suitable resources for execution of CPU-time consuming Monte Carlo (MC) simulation tasks (jobs). Monitored resources are Computer Elements (CEs), Storage Elements (SEs), WMS-servers (WMSs), CernVM File System (CVMFS) available to the VO HONE and local GRID User Interfaces (UIs). The general principle of monitoring GRID elements is based on the execution of short test jobs on different CE queues using submission through various WMSs and directly to the CREAM-CEs as well. Real H1 MC Production jobs with a small number of events are used to perform the tests. Test jobs are periodically submitted into GRID queues, the status of these jobs is checked, output files of completed jobs are retrieved, the result of each job is analyzed and the waiting time and run time are derived. Using this information, the status of the GRID elements is estimated and the most suitable ones are included in the automatically generated configuration files for use in the H1 MC production. The monitoring system allows for identification of problems in the GRID sites and promptly reacts on it (for example by sending GGUS (Global Grid User Support) trouble tickets). The system can easily be adapted to identify the optimal resources for tasks other than MC production, simply by changing to the relevant test jobs. The monitoring system is written mostly in Python and Perl with insertion of a few shell scripts. In addition to the test monitoring system we use information from real production jobs to monitor the availability and quality of the GRID resources. The monitoring tools register the number of job resubmissions, the percentage of failed and finished jobs relative to all jobs on the CEs and determine the average values of waiting and running time for the involved GRID queues. CEs which do not meet the set criteria can be removed from the production chain by including them in an exception table. All of these monitoring actions lead to a more reliable and faster execution of MC requests.

Health Monitor for Multitasking, Safety-Critical, Real-Time Software

NASA Technical Reports Server (NTRS)

Zoerner, Roger

2011-01-01

Health Manager can detect Bad Health prior to a failure occurring by periodically monitoring the application software by looking for code corruption errors, and sanity-checking each critical data value prior to use. A processor s memory can fail and corrupt the software, or the software can accidentally write to the wrong address and overwrite the executing software. This innovation will continuously calculate a checksum of the software load to detect corrupted code. This will allow a system to detect a failure before it happens. This innovation monitors each software task (thread) so that if any task reports "bad health," or does not report to the Health Manager, the system is declared bad. The Health Manager reports overall system health to the outside world by outputting a square wave signal. If the square wave stops, this indicates that system health is bad or hung and cannot report. Either way, "bad health" can be detected, whether caused by an error, corrupted data, or a hung processor. A separate Health Monitor Task is started and run periodically in a loop that starts and stops pending on a semaphore. Each monitored task registers with the Health Manager, which maintains a count for the task. The registering task must indicate if it will run more or less often than the Health Manager. If the task runs more often than the Health Manager, the monitored task calls a health function that increments the count and verifies it did not go over max-count. When the periodic Health Manager runs, it verifies that the count did not go over the max-count and zeroes it. If the task runs less often than the Health Manager, the periodic Health Manager will increment the count. The monitored task zeroes the count, and both the Health Manager and monitored task verify that the count did not go over the max-count.

78 FR 58874 - Airworthiness Directives; PILATUS AIRCRAFT LTD. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-25

... System (ESIS). If the common ground fails both navigations systems could fail simultaneously, which could... flight display (PFD) and the Electronic Standby Instrument System (ESIS). If the common ground fails both navigation systems could fail simultaneously. We are issuing this AD to prevent simultaneous failure of both...

Can Vacuum Assisted Venous Drainage be Achieved using a Roller Pump in an Emergency? A Pilot Study using Neonatal Circuitry

PubMed Central

Hill, S. L.; Holt, D. W.

2007-01-01

Abstract: There has been much advancement in perfusion technology over its 50 years of progression. One of these techniques is vacuum-assisted venous drainage (VAVD). Many perfusionists augment venous drainage using VAVD, typically from a wall vacuum source. This study explores alternates to providing VAVD if the wall vacuum fails. In two porcine laboratories, ∼36 in. of 3/16-in. tubing was connected to a sucker return port and placed into the roller head next to the arterial pump. The vacuum was monitored with a DLP pressure monitoring system (Medtronic). This system was connected to small-bore tubing and attached to a stopcock on top of the reservoir. The vacuum was regulated using another stopcock connected to a non-filtered luer lock port on top of the reservoir or by a segment of 3 × 0.25-in.-diameter tubing attached to the vent port with a c-clamp. Vacuum drainage was achieved, ranging from −18 mmHg to −71 mmHg by manipulating the stopcock or c-clamp. Changes in venous drainage were seen by volume fluctuations in the venous reservoir. The vacuum was adjusted to account for dramatic changes. Augmented venous drainage using a roller pump can be achieved successfully during cardiopulmonary bypass (CPB). This method of active drainage can be used in lieu of wall suction or during times of emergency if wall suction fails. PMID:18293812

Design and evaluation of a simple signaling device for live traps

USGS Publications Warehouse

Benevides, F.L.; Hansen, H.; Hess, S.C.

2008-01-01

Frequent checks of live traps require enormous amounts of labor and add human scents associated with repeated monitoring, which may reduce capture efficiency. To reduce efforts and increase efficiency, we developed a trap-signaling device with long-distance reception, durability in adverse weather, and ease of transport, deployment, and use. Modifications from previous designs include a normally open magnetic switch and a mounting configuration to maximize reception. The system weighed <225 g, was effective ???17.1 km, and failed in <1% of trap-nights. Employing this system, researchers and wildlife managers may reduce the amount of effort checking traps while improving the welfare of trapped animals.

Surveillance application using patten recognition software at the EBR-II Reactor Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olson, D.L.

1992-01-01

The System State Analyzer (SSA) is a software based pattern recognition system. For the past several year this system has been used at Argonne National Laboratory's Experimental Breeder Reactor 2 (EBR-2) reactor for detection of degradation and other abnormalities in plant systems. Currently there are two versions of the SSA being used at EBR-2. One version of SSA is used for daily surveillance and trending of the reactor delta-T and startups of the reactor. Another version of the SSA is the QSSA which is used to monitor individual systems of the reactor such as the Secondary Sodium System, Secondary Sodiummore » Pumps, and Steam Generator. This system has been able to detect problems such as signals being affected by temperature variations due to a failing temperature controller.« less

Surveillance application using patten recognition software at the EBR-II Reactor Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Olson, D.L.

1992-05-01

The System State Analyzer (SSA) is a software based pattern recognition system. For the past several year this system has been used at Argonne National Laboratory`s Experimental Breeder Reactor 2 (EBR-2) reactor for detection of degradation and other abnormalities in plant systems. Currently there are two versions of the SSA being used at EBR-2. One version of SSA is used for daily surveillance and trending of the reactor delta-T and startups of the reactor. Another version of the SSA is the QSSA which is used to monitor individual systems of the reactor such as the Secondary Sodium System, Secondary Sodiummore » Pumps, and Steam Generator. This system has been able to detect problems such as signals being affected by temperature variations due to a failing temperature controller.« less

Linear friction weld process monitoring of fixture cassette deformations using empirical mode decomposition

NASA Astrophysics Data System (ADS)

Bakker, O. J.; Gibson, C.; Wilson, P.; Lohse, N.; Popov, A. A.

2015-10-01

Due to its inherent advantages, linear friction welding is a solid-state joining process of increasing importance to the aerospace, automotive, medical and power generation equipment industries. Tangential oscillations and forge stroke during the burn-off phase of the joining process introduce essential dynamic forces, which can also be detrimental to the welding process. Since burn-off is a critical phase in the manufacturing stage, process monitoring is fundamental for quality and stability control purposes. This study aims to improve workholding stability through the analysis of fixture cassette deformations. Methods and procedures for process monitoring are developed and implemented in a fail-or-pass assessment system for fixture cassette deformations during the burn-off phase. Additionally, the de-noised signals are compared to results from previous production runs. The observed deformations as a consequence of the forces acting on the fixture cassette are measured directly during the welding process. Data on the linear friction-welding machine are acquired and de-noised using empirical mode decomposition, before the burn-off phase is extracted. This approach enables a direct, objective comparison of the signal features with trends from previous successful welds. The capacity of the whole process monitoring system is validated and demonstrated through the analysis of a large number of signals obtained from welding experiments.

Physical activity patterns of ethnic children from low socio-economic environments within the UK.

PubMed

Eyre, Emma Lisa Jane; Duncan, Michael Joseph; Birch, Samantha Louise; Cox, Valerie; Blackett, Matthew

2015-01-01

Many children fail to meet physical activity (PA) guidelines for health benefits. PA behaviours are complex and depend on numerous interrelated factors. The study aims to develop current understanding of how children from low Socio-economic environments within the UK use their surrounding built environments for PA by using advanced technology. The environment was assessed in 96 school children (7-9 years) using global positioning system (GPS) monitoring (Garmin Forerunner, 305). In a subsample of 46 children, the environment and PA were assessed using an integrated GPS and heart rate monitor. The percentage of time spent indoor, outdoor, in green and non-green environments along with time spent in moderate-to-vigorous PA (MVPA) in indoor and outdoor environments were assessed. A 2-by-2 repeated measures analysis of covariance, controlling for body mass index, BF%, assessed the environmental differences. The findings show that 42% of children from deprived wards of Coventry fail to meet PA guidelines, of which 43% was accumulated during school. Children engaged in more MVPA outdoor than indoor environments (P < 0.01) and a greater amount of time was spent in non-green environments (P < 0.01). Increased time outdoors was negatively associated with BF%. In conclusion, outdoor environments are important for health-enhancing PA and reducing fatness in deprived and ethnic children.

Are traditional methods of determining nest predators and nest fates reliable? An experiment with Wood Thrushes (Hylocichla mustelina) using miniature video cameras

USGS Publications Warehouse

Williams, Gary E.; Wood, P.B.

2002-01-01

We used miniature infrared video cameras to monitor Wood Thrush (Hylocichla mustelina) nests during 1998–2000. We documented nest predators and examined whether evidence at nests can be used to predict predator identities and nest fates. Fifty-six nests were monitored; 26 failed, with 3 abandoned and 23 depredated. We predicted predator class (avian, mammalian, snake) prior to review of video footage and were incorrect 57% of the time. Birds and mammals were underrepresented whereas snakes were over-represented in our predictions. We documented ≥9 nest-predator species, with the southern flying squirrel (Glaucomys volans) taking the most nests (n = 8). During 2000, we predicted fate (fledge or fail) of 27 nests; 23 were classified correctly. Traditional methods of monitoring nests appear to be effective for classifying success or failure of nests, but ineffective at classifying nest predators.

Quality Assurance in Post-Secondary Education: Some Common Approaches

ERIC Educational Resources Information Center

Law, Dennis Chung Sea

2010-01-01

Purpose: The common approaches to quality assurance (QA), as practiced by most post-secondary education institutions for internal quality monitoring and most QA authorities for external quality monitoring (EQM), have been considered by many researchers as having largely failed to address the essence of educational quality. The purpose of this…

40 CFR 123.45 - Noncompliance and program reporting by the Director.

Code of Federal Regulations, 2014 CFR

2014-07-01

... (CONTINUED) WATER PROGRAMS STATE PROGRAM REQUIREMENTS Transfer of Information and Permit Review § 123.45... schedule report for final compliance or a monitoring report. This applies when the permittee has failed to submit a final compliance schedule progress report, pretreatment report, or a Discharge Monitoring Report...

40 CFR 123.45 - Noncompliance and program reporting by the Director.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) WATER PROGRAMS STATE PROGRAM REQUIREMENTS Transfer of Information and Permit Review § 123.45... schedule report for final compliance or a monitoring report. This applies when the permittee has failed to submit a final compliance schedule progress report, pretreatment report, or a Discharge Monitoring Report...

40 CFR 123.45 - Noncompliance and program reporting by the Director.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) WATER PROGRAMS STATE PROGRAM REQUIREMENTS Transfer of Information and Permit Review § 123.45... schedule report for final compliance or a monitoring report. This applies when the permittee has failed to submit a final compliance schedule progress report, pretreatment report, or a Discharge Monitoring Report...

40 CFR 123.45 - Noncompliance and program reporting by the Director.

Code of Federal Regulations, 2013 CFR

2013-07-01

... (CONTINUED) WATER PROGRAMS STATE PROGRAM REQUIREMENTS Transfer of Information and Permit Review § 123.45... schedule report for final compliance or a monitoring report. This applies when the permittee has failed to submit a final compliance schedule progress report, pretreatment report, or a Discharge Monitoring Report...

Agent Transparency for an Autonomous Squad Member

DTIC Science & Technology

2015-05-01

C. Attentional  Control  Survey  41  Appendix D. System Usability Scale  45  Appendix E. Modified Jian Pre‐Post Trust Survey  47  Appendix F.  Posttest ...failing to comply with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE...information in a simulation-based unmanned ground vehicle monitoring task. Three groups were tested with visual displays representing 1 of 3 types of

Keeping Up with Healthcare Trends: IcHeart as a Medication Management Application

NASA Astrophysics Data System (ADS)

Kasinathan, Vinothini; Mustapha, Aida; Azah Samsudin, Noor

2016-11-01

According to the US governments, more than 125,000 people die each year due to failure to manage their medications, leading to approximately USD100 billion in preventable costs to healthcare systems. The core failure in medication management is attributed by patients failing to adhere their medication regimens, whether by accident, negligence, or intentional. Recognizing the importants of vigilant monitoring in medication management, this paper is set to review the latest android-based healthcare trends and propose a new mobile medication reminder application called IcHeart.

Systems and methods for circuit lifetime evaluation

NASA Technical Reports Server (NTRS)

Heaps, Timothy L. (Inventor); Sheldon, Douglas J. (Inventor); Bowerman, Paul N. (Inventor); Everline, Chester J. (Inventor); Shalom, Eddy (Inventor); Rasmussen, Robert D. (Inventor)

2013-01-01

Systems and methods for estimating the lifetime of an electrical system in accordance with embodiments of the invention are disclosed. One embodiment of the invention includes iteratively performing Worst Case Analysis (WCA) on a system design with respect to different system lifetimes using a computer to determine the lifetime at which the worst case performance of the system indicates the system will pass with zero margin or fail within a predetermined margin for error given the environment experienced by the system during its lifetime. In addition, performing WCA on a system with respect to a specific system lifetime includes identifying subcircuits within the system, performing Extreme Value Analysis (EVA) with respect to each subcircuit to determine whether the subcircuit fails EVA for the specific system lifetime, when the subcircuit passes EVA, determining that the subcircuit does not fail WCA for the specified system lifetime, when a subcircuit fails EVA performing at least one additional WCA process that provides a tighter bound on the WCA than EVA to determine whether the subcircuit fails WCA for the specified system lifetime, determining that the system passes WCA with respect to the specific system lifetime when all subcircuits pass WCA, and determining that the system fails WCA when at least one subcircuit fails WCA.

Model-Based Sensor Placement for Component Condition Monitoring and Fault Diagnosis in Fossil Energy Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mobed, Parham; Pednekar, Pratik; Bhattacharyya, Debangsu

Design and operation of energy producing, near “zero-emission” coal plants has become a national imperative. This report on model-based sensor placement describes a transformative two-tier approach to identify the optimum placement, number, and type of sensors for condition monitoring and fault diagnosis in fossil energy system operations. The algorithms are tested on a high fidelity model of the integrated gasification combined cycle (IGCC) plant. For a condition monitoring network, whether equipment should be considered at a unit level or a systems level depends upon the criticality of the process equipment, its likeliness to fail, and the level of resolution desiredmore » for any specific failure. Because of the presence of a high fidelity model at the unit level, a sensor network can be designed to monitor the spatial profile of the states and estimate fault severity levels. In an IGCC plant, besides the gasifier, the sour water gas shift (WGS) reactor plays an important role. In view of this, condition monitoring of the sour WGS reactor is considered at the unit level, while a detailed plant-wide model of gasification island, including sour WGS reactor and the Selexol process, is considered for fault diagnosis at the system-level. Finally, the developed algorithms unify the two levels and identifies an optimal sensor network that maximizes the effectiveness of the overall system-level fault diagnosis and component-level condition monitoring. This work could have a major impact on the design and operation of future fossil energy plants, particularly at the grassroots level where the sensor network is yet to be identified. In addition, the same algorithms developed in this report can be further enhanced to be used in retrofits, where the objectives could be upgrade (addition of more sensors) and relocation of existing sensors.« less

Examining the Relationship Between Mental, Physical, and Organizational Factors Associated With Attrition During Maritime Forces Training.

PubMed

Binsch, Olaf; Banko, Katherine M; Veenstra, Bertil J; Valk, Pierre J L

2015-11-01

For infantry units of the Dutch Ministry of Defence, high attrition rates (varying from 42 to 68%) during initial training are a persisting problem. The reasons for this attrition are diverse. Having better insight into the causes of attrition is a prerequisite for implementing preventive measures. To achieve this, a monitoring assessment system was developed that integrated the effects of physical, mental, and organizational determinants on operational readiness. The aim of this study was to implement the monitoring tools and to establish the set of determinants that best predicted attrition during infantry training of new recruits. Eighty-five recruits were monitored over a 24-week infantry training course. Before the training, recruits were screened for medical, psychological, and physical wellness. During the monitoring phase, mental, physiological, and organizational indicants were obtained using an array of tools such as questionnaires, chest belt monitors (for heart rate, acceleration, and skin temperature measurements), and computerized tests (e.g., vigilance, long-term memory). Survival analyses were used to tease out the determinants of individual and grouped predictors of attrition. Nearly half the recruits (47%) failed the training. Attrition was predicted by both physiological and mental determinants. However, the organizational determinant "trainers' judgment" on the "recruits' military quality" dominated the physiological and mental determinants. It was concluded that the monitoring system was successfully implemented during infantry training, and that the survival analysis method emphasized on single effects and interactions between the different determinants. Based on the current findings, we recommend several steps to successfully implement a monitoring method in settings with high demands.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Physical device safety is typically implemented locally using embedded controllers, while operations safety is primarily performed in control centers. Safe operations can be enhanced by correct design of device-level control algorithms, and protocols, procedures and operator training at the control-room level, but all can fail. Moreover, these elements exchange data and issue commands via vulnerable communication layers. In order to secure these gaps and enhance operational safety, we believe monitoring of command sequences must be combined with an awareness of physical device limitations and automata models that capture safety mechanisms. One way of doing this is by leveraging specification-based intrusionmore » detection to monitor for physical constraint violations. The method can also verify that physical infrastructure state is consistent with monitoring information and control commands exchanged between field devices and control centers. This additional security layer enhances protection from both outsider attacks and insider mistakes. We implemented specification-based SCADA command analyzers using physical constraint algorithms directly in the Bro framework and Broccoli APIs for three separate scenarios: a water heater, an automated distribution system, and an over-current protection scheme. To accomplish this, we added low-level analyzers capable of examining control system-specific protocol packets for both Modbus TCP and DNP3, and also higher-level analyzers able to interpret device command and data streams within the context of each device's physical capabilities and present operational state. Thus the software that we are making available includes the Bro/Broccoli scripts for these three scenarios, as well as simulators, written in C, of those scenarios that generate sample traffic that is monitored by the Bro/Broccoli scripts. In addition, we have also implemented systems to directly pull cyber-physical information from the OSIsoft PI historian system. We have included the Python scripts used to perform that monitoring.« less

Wind turbine blade fatigue tests: lessons learned and application to SHM system development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Stuart G.; Farinholt, Kevin M.; Jeong, Hyomi

2012-06-28

This paper presents experimental results of several structural health monitoring (SHM) methods applied to a 9-meter CX-100 wind turbine blade that underwent fatigue loading. The blade was instrumented with piezoelectric transducers, accelerometers, acoustic emission sensors, and foil strain gauges. It underwent harmonic excitation at its first natural frequency using a hydraulically actuated resonant excitation system. The blade was initially excited at 25% of its design load, and then with steadily increasing loads until it failed. Various data were collected between and during fatigue loading sessions. The data were measured over multiple frequency ranges using a variety of acquisition equipment, includingmore » off-the-shelf systems and specially designed hardware developed by the authors. Modal response, diffuse wave-field transfer functions, and ultrasonic guided wave methods were applied to assess the condition of the wind turbine blade. The piezoelectric sensors themselves were also monitored using a sensor diagnostics procedure. This paper summarizes experimental procedures and results, focusing particularly on fatigue crack detection, and concludes with considerations for implementing such damage identification systems, which will be used as a guideline for future SHM system development for operating wind turbine blades.« less

Beam Loss Monitoring for LHC Machine Protection

NASA Astrophysics Data System (ADS)

Holzer, Eva Barbara; Dehning, Bernd; Effnger, Ewald; Emery, Jonathan; Grishin, Viatcheslav; Hajdu, Csaba; Jackson, Stephen; Kurfuerst, Christoph; Marsili, Aurelien; Misiowiec, Marek; Nagel, Markus; Busto, Eduardo Nebot Del; Nordt, Annika; Roderick, Chris; Sapinski, Mariusz; Zamantzas, Christos

The energy stored in the nominal LHC beams is two times 362 MJ, 100 times the energy of the Tevatron. As little as 1 mJ/cm3 deposited energy quenches a magnet at 7 TeV and 1 J/cm3 causes magnet damage. The beam dumps are the only places to safely dispose of this beam. One of the key systems for machine protection is the beam loss monitoring (BLM) system. About 3600 ionization chambers are installed at likely or critical loss locations around the LHC ring. The losses are integrated in 12 time intervals ranging from 40 μs to 84 s and compared to threshold values defined in 32 energy ranges. A beam abort is requested when potentially dangerous losses are detected or when any of the numerous internal system validation tests fails. In addition, loss data are used for machine set-up and operational verifications. The collimation system for example uses the loss data for set-up and regular performance verification. Commissioning and operational experience of the BLM are presented: The machine protection functionality of the BLM system has been fully reliable; the LHC availability has not been compromised by false beam aborts.

Simulating fail-stop in asynchronous distributed systems

NASA Technical Reports Server (NTRS)

Sabel, Laura; Marzullo, Keith

1994-01-01

The fail-stop failure model appears frequently in the distributed systems literature. However, in an asynchronous distributed system, the fail-stop model cannot be implemented. In particular, it is impossible to reliably detect crash failures in an asynchronous system. In this paper, we show that it is possible to specify and implement a failure model that is indistinguishable from the fail-stop model from the point of view of any process within an asynchronous system. We give necessary conditions for a failure model to be indistinguishable from the fail-stop model, and derive lower bounds on the amount of process replication needed to implement such a failure model. We present a simple one-round protocol for implementing one such failure model, which we call simulated fail-stop.

Sixty-four-Channel Inline Cable Tester

NASA Technical Reports Server (NTRS)

2008-01-01

Faults in wiring are a serious concern for the aerospace and aeronautics (commercial, military, and civil) industries. A number of accidents have occurred because faulty wiring created shorts or opens that resulted in the loss of control of the aircraft or because arcing led to fires and explosions. Some of these accidents have resulted in the massive loss of lives (such as in the TWA Flight 800 accident). Circuits on the Space Shuttle have also failed because of faulty insulation on wiring. STS-93 lost power when a primary power circuit in one engine failed and a second engine had a backup power circuit fault. Cables are usually tested on the ground after the crew reports a fault encountered during flight. Often such failures result from vibration and cannot be replicated while the aircraft is stationary. It is therefore important to monitor faults while the aircraft is in operation, when cables are more likely to fail. Work is in progress to develop a cable fault tester capable of monitoring up to 64 individual wires simultaneously. Faults can be monitored either inline or offline. In the inline mode of operation, the monitoring is performed without disturbing the normal operation of the wires under test. That is, the operations are performed unintrusively and are essentially undetectable for the test signal levels are below the noise floor. A cable can be monitored several times per second in the offline mode and once a second in the inline mode. The 64-channel inline cable tester not only detects the occurrence of a fault, but also determines the type of fault (short/open) and the location of the fault. This will enable the detection of intermittent faults that can be repaired before they become serious problems.

The Monitoring and Responding Behaviours of Proficient Fourth Grade Readers to Miscues on a Complex Scientific Text

ERIC Educational Resources Information Center

Kucer, Stephen B.

2017-01-01

The monitoring of meaning and the correction of miscues that fail to make sense are a hallmark of a proficient reader. Much of the research, however, has focused on the reading of fictional, narrative texts. In contrast, this research examines the monitoring and response behaviours of 35 proficient fourth grade readers (nine and 10 years of age)…

Intelligent approach to prognostic enhancements of diagnostic systems

NASA Astrophysics Data System (ADS)

Vachtsevanos, George; Wang, Peng; Khiripet, Noppadon; Thakker, Ash; Galie, Thomas R.

2001-07-01

This paper introduces a novel methodology to prognostics based on a dynamic wavelet neural network construct and notions from the virtual sensor area. This research has been motivated and supported by the U.S. Navy's active interest in integrating advanced diagnostic and prognostic algorithms in existing Naval digital control and monitoring systems. A rudimentary diagnostic platform is assumed to be available providing timely information about incipient or impending failure conditions. We focus on the development of a prognostic algorithm capable of predicting accurately and reliably the remaining useful lifetime of a failing machine or component. The prognostic module consists of a virtual sensor and a dynamic wavelet neural network as the predictor. The virtual sensor employs process data to map real measurements into difficult to monitor fault quantities. The prognosticator uses a dynamic wavelet neural network as a nonlinear predictor. Means to manage uncertainty and performance metrics are suggested for comparison purposes. An interface to an available shipboard Integrated Condition Assessment System is described and applications to shipboard equipment are discussed. Typical results from pump failures are presented to illustrate the effectiveness of the methodology.

ReadySteady: app for accelerometer-based activity monitoring and wellness-motivation feedback system for older adults.

PubMed

Vankipuram, Mithra; McMahon, Siobhan; Fleury, Julie

2012-01-01

Increased physical activity and exercise have been found to reduce falls and decrease mortality and age-related morbidity in older adults. However, a large percentage of this population fail to achieve the necessary levels of activity needed to support health living. In this work, we present a mobile app developed on the iOS platform that monitors activity levels using accelerometry. The data captured by the sensor is utilized to provide real-time motivational feedback to enable reinforcement of positive behaviors in older adults. Pilot experiments (conducted with younger adults) performed to assess validity of activity measurement showed that system accurately measures sedentary, light, moderate and vigorous activities in a controlled lab setting. Pilot tests (conducted with older adults) in the user setting showed that while the app is adept at capturing gross body activity (such as sitting, walking and jogging), additional sensors may be required to capture activities involving the extremities.

Correlations of Melt Pool Geometry and Process Parameters During Laser Metal Deposition by Coaxial Process Monitoring

NASA Astrophysics Data System (ADS)

Ocylok, Sörn; Alexeev, Eugen; Mann, Stefan; Weisheit, Andreas; Wissenbach, Konrad; Kelbassa, Ingomar

One major demand of today's laser metal deposition (LMD) processes is to achieve a fail-save build-up regarding changing conditions like heat accumulations. Especially for the repair of thin parts like turbine blades is the knowledge about the correlations between melt pool behavior and process parameters like laser power, feed rate and powder mass stream indispensable. The paper will show the process layout with the camera based coaxial monitoring system and the quantitative influence of the process parameters on the melt pool geometry. Therefore the diameter, length and area of the melt pool are measured by a video analytic system at various parameters and compared with the track wide in cross-sections and the laser spot diameter. The influence of changing process conditions on the melt pool is also investigated. On the base of these results an enhanced process of the build-up of a multilayer one track fillet geometry will be presented.

Acoustic monitoring on a humpback whale (Megaptera novaeangliae) feeding ground shows continual singing into late Spring.

PubMed

Clark, Christopher W; Clapham, Phillip J

2004-05-22

Singing by males is a major feature of the mating system of humpback whales, Megaptera novaeangliae (Borowski). Although a few songs have been opportunistically recorded on the whales' high-latitude feeding grounds, singing in these regions was thought to be only sporadic. We report results from the first continuous acoustic monitoring of a humpback whale feeding ground (off Cape Cod, MA, USA) in spring. Using autonomous sea-floor recording systems, we found singing on a daily basis over the entire 25 day monitoring period, from 14 May to 7 June 2000. For much of the period, song was recorded 24 h per day. These results, combined with evidence for aseasonal conceptions in whaling catch data, suggest that the humpback whale breeding season should no longer be considered as confined to lower-latitude regions in winter. Rather, we suggest breeding extends geographically and temporally onto feeding grounds into at least spring and early summer. Singing at these times represents either low-cost opportunistic advertising by (perhaps relatively few) males to court females that failed to conceive during the winter, and/or possibly an intrasexual display.

SIG-VISA: Signal-based Vertically Integrated Seismic Monitoring

NASA Astrophysics Data System (ADS)

Moore, D.; Mayeda, K. M.; Myers, S. C.; Russell, S.

2013-12-01

Traditional seismic monitoring systems rely on discrete detections produced by station processing software; however, while such detections may constitute a useful summary of station activity, they discard large amounts of information present in the original recorded signal. We present SIG-VISA (Signal-based Vertically Integrated Seismic Analysis), a system for seismic monitoring through Bayesian inference on seismic signals. By directly modeling the recorded signal, our approach incorporates additional information unavailable to detection-based methods, enabling higher sensitivity and more accurate localization using techniques such as waveform matching. SIG-VISA's Bayesian forward model of seismic signal envelopes includes physically-derived models of travel times and source characteristics as well as Gaussian process (kriging) statistical models of signal properties that combine interpolation of historical data with extrapolation of learned physical trends. Applying Bayesian inference, we evaluate the model on earthquakes as well as the 2009 DPRK test event, demonstrating a waveform matching effect as part of the probabilistic inference, along with results on event localization and sensitivity. In particular, we demonstrate increased sensitivity from signal-based modeling, in which the SIGVISA signal model finds statistical evidence for arrivals even at stations for which the IMS station processing failed to register any detection.

Control system failure monitoring using generalized parity relations. M.S. Thesis Interim Technical Report

NASA Technical Reports Server (NTRS)

Vanschalkwyk, Christiaan Mauritz

1991-01-01

Many applications require that a control system must be tolerant to the failure of its components. This is especially true for large space-based systems that must work unattended and with long periods between maintenance. Fault tolerance can be obtained by detecting the failure of the control system component, determining which component has failed, and reconfiguring the system so that the failed component is isolated from the controller. Component failure detection experiments that were conducted on an experimental space structure, the NASA Langley Mini-Mast are presented. Two methodologies for failure detection and isolation (FDI) exist that do not require the specification of failure modes and are applicable to both actuators and sensors. These methods are known as the Failure Detection Filter and the method of Generalized Parity Relations. The latter method was applied to three different sensor types on the Mini-Mast. Failures were simulated in input-output data that were recorded during operation of the Mini-Mast. Both single and double sensor parity relations were tested and the effect of several design parameters on the performance of these relations is discussed. The detection of actuator failures is also treated. It is shown that in all the cases it is possible to identify the parity relations directly from input-output data. Frequency domain analysis is used to explain the behavior of the parity relations.

Monitoring of large-scale federated data storage: XRootD and beyond

NASA Astrophysics Data System (ADS)

Andreeva, J.; Beche, A.; Belov, S.; Diguez Arias, D.; Giordano, D.; Oleynik, D.; Petrosyan, A.; Saiz, P.; Tadel, M.; Tuckett, D.; Vukotic, I.

2014-06-01

The computing models of the LHC experiments are gradually moving from hierarchical data models with centrally managed data pre-placement towards federated storage which provides seamless access to data files independently of their location and dramatically improve recovery due to fail-over mechanisms. Construction of the data federations and understanding the impact of the new approach to data management on user analysis requires complete and detailed monitoring. Monitoring functionality should cover the status of all components of the federated storage, measuring data traffic and data access performance, as well as being able to detect any kind of inefficiencies and to provide hints for resource optimization and effective data distribution policy. Data mining of the collected monitoring data provides a deep insight into new usage patterns. In the WLCG context, there are several federations currently based on the XRootD technology. This paper will focus on monitoring for the ATLAS and CMS XRootD federations implemented in the Experiment Dashboard monitoring framework. Both federations consist of many dozens of sites accessed by many hundreds of clients and they continue to grow in size. Handling of the monitoring flow generated by these systems has to be well optimized in order to achieve the required performance. Furthermore, this paper demonstrates the XRootD monitoring architecture is sufficiently generic to be easily adapted for other technologies, such as HTTP/WebDAV dynamic federations.

Adaptive model training system and method

DOEpatents

Bickford, Randall L; Palnitkar, Rahul M; Lee, Vo

2014-04-15

An adaptive model training system and method for filtering asset operating data values acquired from a monitored asset for selectively choosing asset operating data values that meet at least one predefined criterion of good data quality while rejecting asset operating data values that fail to meet at least the one predefined criterion of good data quality; and recalibrating a previously trained or calibrated model having a learned scope of normal operation of the asset by utilizing the asset operating data values that meet at least the one predefined criterion of good data quality for adjusting the learned scope of normal operation of the asset for defining a recalibrated model having the adjusted learned scope of normal operation of the asset.

Adaptive model training system and method

DOEpatents

Bickford, Randall L; Palnitkar, Rahul M

2014-11-18

An adaptive model training system and method for filtering asset operating data values acquired from a monitored asset for selectively choosing asset operating data values that meet at least one predefined criterion of good data quality while rejecting asset operating data values that fail to meet at least the one predefined criterion of good data quality; and recalibrating a previously trained or calibrated model having a learned scope of normal operation of the asset by utilizing the asset operating data values that meet at least the one predefined criterion of good data quality for adjusting the learned scope of normal operation of the asset for defining a recalibrated model having the adjusted learned scope of normal operation of the asset.

Implantable Hemodynamic Monitoring for Heart Failure Patients.

PubMed

Abraham, William T; Perl, Leor

2017-07-18

Rates of heart failure hospitalization remain unacceptably high. Such hospitalizations are associated with substantial patient, caregiver, and economic costs. Randomized controlled trials of noninvasive telemedical systems have failed to demonstrate reduced rates of hospitalization. The failure of these technologies may be due to the limitations of the signals measured. Intracardiac and pulmonary artery pressure-guided management has become a focus of hospitalization reduction in heart failure. Early studies using implantable hemodynamic monitors demonstrated the potential of pressure-based heart failure management, whereas subsequent studies confirmed the clinical utility of this approach. One large pivotal trial proved the safety and efficacy of pulmonary artery pressure-guided heart failure management, showing a marked reduction in heart failure hospitalizations in patients randomized to active pressure-guided management. "Next-generation" implantable hemodynamic monitors are in development, and novel approaches for the use of this data promise to expand the use of pressure-guided heart failure management. Copyright © 2017 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

The HoMedics BPA-200 and BPA-300 home blood pressure devices fail the European Society of Hypertension International Protocol and cannot be recommended for patient use.

PubMed

Grim, Clarence E; Grim, Carlene M

2008-08-01

We have tested two home blood pressure monitors made by the HoMedics, Inc., 300 Pontiac Trail, Commerce Township, Michigan 48390, USA, using the European Society of Hypertension International Protocol. Both failed and we believe it is important to get this into the literature quickly to protect patients and practitioners.

Implementation. Improving caries detection, assessment, diagnosis and monitoring.

PubMed

Pitts, N B

2009-01-01

This chapter deals with improving the detection, assessment, diagnosis and monitoring of caries to ensure optimal personalized caries management. This can be achieved by delivering what we have (synthesized evidence and international consensus) better and more consistently, as well as driving research and innovation in the areas where we need them. There is a need to better understand the interrelated pieces of the jigsaw that makes up evidence-based dentistry, i.e. the linkages between (a) research and synthesis, (b) dissemination of research results and (c) the implementation of research findings which should ensure that research findings change practice at the clinician-patient level. The current situation is outlined; it is at the implementation step where preventive caries control seems to have failed in some countries but not others. Opportunities for implementation include: capitalizing on the World Health Organization's global policy for improvement of oral health, which sets out an action plan for health promotion and integrated disease prevention; utilizing the developments around the International Caries Detection and Assessment System wardrobe of options and e-learning; building on initiatives from the International Dental Federation and the American Dental Association and linking these to patients' preferences, the wider moves to wellbeing and health maintenance. Challenges for implementation include the slow pace of evolution around dental remuneration systems and some groups of dentists failing to embrace clinical prevention. In the future, implementation of current and developing evidence should be accompanied by research into getting research findings into routine practice, with impacts on the behaviour of patients, professionals and policy makers. Copyright 2009 S. Karger AG, Basel

The Anatahan volcano-monitoring system

NASA Astrophysics Data System (ADS)

Marso, J. N.; Lockhart, A. B.; White, R. A.; Koyanagi, S. K.; Trusdell, F. A.; Camacho, J. T.; Chong, R.

2003-12-01

A real-time 24/7 Anatahan volcano-monitoring and eruption detection system is now operational. There had been no real-time seismic monitoring on Anatahan during the May 10, 2003 eruption because the single telemetered seismic station on Anatahan Island had failed. On May 25, staff from the Emergency Management Office (EMO) of the Commonwealth of the Northern Mariana Islands and the U. S. Geological Survey (USGS) established a replacement telemetered seismic station on Anatahan whose data were recorded on a drum recorder at the EMO on Saipan, 130 km to the south by June 5. In late June EMO and USGS staff installed a Glowworm seismic data acquisition system (Marso et al, 2003) at EMO and hardened the Anatahan telemetry links. The Glowworm system collects the telemetered seismic data from Anatahan and Saipan, places graphical display products on a webpage, and exports the seismic waveform data in real time to Glowworm systems at Hawaii Volcano Observatory and Cascades Volcano Observatory (CVO). In early July, a back-up telemetered seismic station was placed on Sarigan Island 40 km north of Anatahan, transmitting directly to the EMO on Saipan. Because there is currently no population on the island, at this time the principal hazard presented by Anatahan volcano would be air traffic disruption caused by possible erupted ash. The aircraft/ash hazard requires a monitoring program that focuses on eruption detection. The USGS currently provides 24/7 monitoring of Anatahan with a rotational seismic duty officer who carries a Pocket PC-cell phone combination that receives SMS text messages from the CVO Glowworm system when it detects large seismic signals. Upon receiving an SMS text message notification from the CVO Glowworm, the seismic duty officer can use the Pocket PC - cell phone to view a graphic of the seismic traces on the EMO Glowworm's webpage to determine if the seismic signal is eruption related. There have been no further eruptions since the monitoring system was installed, but regional tectonic earthquakes have provided frequent tests of the system. Reliance on a Pocket PC - cell phone requires that the seismic duty officer remain in an area with cell phone coverage. With this monitoring method, the USGS is able to provide rapid notice of an Anatahan eruption to the EMO and the Washington Volcano Ash Advisory Center. Reference Marso, J.N., Murray, T.L., Lockhart, A.B., Bryan, C.J., Glowworm: An extended PC-based Earthworm system for volcano monitoring. Abstracts, Cities On Volcanoes III, Hilo Hawaii, July 2003.

Design and testing of integrated Bragg grating sensor systems for advanced grid structure

NASA Astrophysics Data System (ADS)

Amano, Masataro; Mizutani, Tadahito; Okabe, Yoji; Takeda, Nobuo; Ozaki, Tsuyoshi

2006-03-01

In this research, the authors target on the construction of structural health monitoring system of Advanced Grid Structure (AGS) made of Carbon fiber reinforced plastic (CFRP). AGS has often been applied to aerospace structures because of the following advantages: (1) Since ribs carry only axial forces, the weakness in the transverse direction of the CFRP unidirectional laminates is negligible. (2) AGS has damage tolerance because the fracture of a rib hardly affects other ribs, namely AGS is a fail-safe structure. In this research, in order to detect existence and regions of rib fractures in AGS, we embedded multiplexed fiber Bragg grating (FBG) sensors into AGS in rib longitudinal directions for measurement of strains. Monitoring of the change in rib longitudinal strains is the most effective SHM system for AGS. In order to confirm our proposal, we carried out following discussions. First, we analytically revealed that the change in rib longitudinal strains was the most sensitive signal for damage detection because of AGS's structural redundancy. Then, we introduced a statistical outlier analysis technique into the SHM system for damage recognition. Finally, we established AGS with the SHM system and verified experimentally. The result of the test showed that damage existence and regions in AGS could be detected with the proposed SHM system.

Using a Monitoring Process to Effectively Assist Struggling Pre-Service Teacher Candidates

ERIC Educational Resources Information Center

Kincaid, Maureen; Keiser, Nancy

2014-01-01

A critical issue in teacher preparation today is that some candidates meet the criteria for admission to teacher education programs yet they struggle or fail to develop the levels of knowledge, skills, and/or dispositions required to complete the program. This article offers three different case studies to examine the monitoring process developed…

Specification and Verification of Medical Monitoring System Using Petri-nets.

PubMed

Majma, Negar; Babamir, Seyed Morteza

2014-07-01

To monitor the patient behavior, data are collected from patient's body by a medical monitoring device so as to calculate the output using embedded software. Incorrect calculations may endanger the patient's life if the software fails to meet the patient's requirements. Accordingly, the veracity of the software behavior is a matter of concern in the medicine; moreover, the data collected from the patient's body are fuzzy. Some methods have already dealt with monitoring the medical monitoring devices; however, model based monitoring fuzzy computations of such devices have been addressed less. The present paper aims to present synthesizing a fuzzy Petri-net (FPN) model to verify behavior of a sample medical monitoring device called continuous infusion insulin (INS) because Petri-net (PN) is one of the formal and visual methods to verify the software's behavior. The device is worn by the diabetic patients and then the software calculates the INS dose and makes a decision for injection. The input and output of the infusion INS software are not crisp in the real world; therefore, we present them in fuzzy variables. Afterwards, we use FPN instead of clear PN to model the fuzzy variables. The paper follows three steps to synthesize an FPN to deal with verification of the infusion INS device: (1) Definition of fuzzy variables, (2) definition of fuzzy rules and (3) design of the FPN model to verify the software behavior.

Using the Domain Name System to Thwart Automated Client-Based Attacks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Curtis R; Shue, Craig A

2011-09-01

On the Internet, attackers can compromise systems owned by other people and then use these systems to launch attacks automatically. When attacks such as phishing or SQL injections are successful, they can have negative consequences including server downtime and the loss of sensitive information. Current methods to prevent such attacks are limited in that they are application-specific, or fail to block attackers. Phishing attempts can be stopped with email filters, but if the attacker manages to successfully bypass these filters, then the user must determine if the email is legitimate or not. Unfortunately, they often are unable to do so.more » Since attackers have a low success rate, they attempt to compensate for it in volume. In order to have this high throughput, attackers take shortcuts and break protocols. We use this knowledge to address these issues by implementing a system that can detect malicious activity and use it to block attacks. If the client fails to follow proper procedure, they can be classified as an attacker. Once an attacker has been discovered, they will be isolated and monitored. This can be accomplished using existing software in Ubuntu Linux applications, along with our custom wrapper application. After running the system and seeing its performance on three popular Web browsers Chromium, Firefox and Internet Explorer as well as two popular email clients, Thunderbird and Evolution, we found that not only is this system conceivable, it is effective and has low overhead.« less

Going beyond panaceas

PubMed Central

Ostrom, Elinor; Janssen, Marco A.; Anderies, John M.

2007-01-01

In the context of governance of human–environment interactions, a panacea refers to a blueprint for a single type of governance system (e.g., government ownership, privatization, community property) that is applied to all environmental problems. The aim of this special feature is to provide theoretical analysis and empirical evidence to caution against the tendency, when confronted with pervasive uncertainty, to believe that scholars can generate simple models of linked social–ecological systems and deduce general solutions to the overuse of resources. Practitioners and scholars who fall into panacea traps falsely assume that all problems of resource governance can be represented by a small set of simple models, because they falsely perceive that the preferences and perceptions of most resource users are the same. Readers of this special feature will become acquainted with many cases in which panaceas fail. The articles provide an excellent overview of why they fail. Furthermore, the articles in this special feature address how scholars and public officials can increase the prospects for future sustainable resource use by facilitating a diagnostic approach in selecting appropriate starting points for governance and monitoring, as well as by learning from the outcomes of new policies and adapting in light of effective feedback. PMID:17881583

Monitored execution of robot plans produced by STRIPS.

NASA Technical Reports Server (NTRS)

Fikes, R. E.

1972-01-01

We describe PLANEX1, a plan executor for the Stanford Research Institute robot system. The problem-solving program STRIPS creates a plan consisting of a sequence of actions, and PLANEX1 program carries out the plan by executing the actions. PLANEX1 is designed so that it executes only that portion of the plan necessary for completing the task, reexecutes any portion of the plan that has failed to achieve the desired results, and initiates replanning in situations where the plan can no longer be effective in completing the task. The scenario for an example plan execution is given.

Washington’s and Moscow’s Failed Policies Toward Russian Defense Reform

DTIC Science & Technology

1997-04-01

NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME AND ADDRESS Air War College Maxwell AFB, AL36112 8. PERFORMING... ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME AND ADDRESS , 10. SPONSOR/MONITOR’S ACRONYM(S) 11. SPONSOR/MONITOR’S REPORT NUMBER(S) 12...During the Soviet era, the MIC was centrally-directed by eight Ministries organized under the USSR Military-Industrial Commission, or VPK

Are two systemic fish assemblage sampling programmes on the upper Mississippi River telling us the same thing?

USGS Publications Warehouse

Dukerschein, J.T.; Bartels, A.D.; Ickes, B.S.; Pearson, M.S.

2013-01-01

We applied an Index of Biotic Integrity (IBI) used on Wisconsin/Minnesota waters of the upper Mississippi River (UMR) to compare data from two systemic sampling programmes. Ability to use data from multiple sampling programmes could extend spatial and temporal coverage of river assessment and monitoring efforts. We normalized for effort and tested fish community data collected by the Environmental Monitoring and Assessment Program-Great Rivers Ecosystems (EMAP-GRE) 2004–2006 and the Long Term Resource Monitoring Program (LTRMP) 1993–2006. Each programme used daytime electrofishing along main channel borders but with some methodological and design differences. EMAP-GRE, designed for baseline and, eventually, compliance monitoring, used a probabilistic, continuous design. LTRMP, designed primarily for baseline and trend monitoring, used a stratified random design in five discrete study reaches. Analysis of similarity indicated no significant difference between EMAP-GRE and LTRMP IBI scores (n=238; Global R= 0.052; significance level=0.972). Both datasets distinguished clear differences only between 'Fair' and 'Poor' condition categories, potentially supporting a 'pass–fail' assessment strategy. Thirteen years of LTRMP data demonstrated stable IBI scores through time in four of five reaches sampled. LTRMP and EMAPGRE IBI scores correlated along the UMR's upstream to downstream gradient (df [3, 25]; F=1.61; p=0.22). A decline in IBI scores from upstream to downstream was consistent with UMR fish community studies and a previous, empirically modelled human disturbance gradient. Comparability between EMAP-GRE (best upstream to downstream coverage) and LTRMP data (best coverage over time and across the floodplain) supports a next step of developing and testing a systemic, multi-metric fish index on the UMR that both approaches could inform.

A better way to evaluate remote monitoring programs in chronic disease care: receiver operating characteristic analysis.

PubMed

Brown Connolly, Nancy E

2014-12-01

This foundational study applies the process of receiver operating characteristic (ROC) analysis to evaluate utility and predictive value of a disease management (DM) model that uses RM devices for chronic obstructive pulmonary disease (COPD). The literature identifies a need for a more rigorous method to validate and quantify evidence-based value for remote monitoring (RM) systems being used to monitor persons with a chronic disease. ROC analysis is an engineering approach widely applied in medical testing, but that has not been evaluated for its utility in RM. Classifiers (saturated peripheral oxygen [SPO2], blood pressure [BP], and pulse), optimum threshold, and predictive accuracy are evaluated based on patient outcomes. Parametric and nonparametric methods were used. Event-based patient outcomes included inpatient hospitalization, accident and emergency, and home health visits. Statistical analysis tools included Microsoft (Redmond, WA) Excel(®) and MedCalc(®) (MedCalc Software, Ostend, Belgium) version 12 © 1993-2013 to generate ROC curves and statistics. Persons with COPD were monitored a minimum of 183 days, with at least one inpatient hospitalization within 12 months prior to monitoring. Retrospective, de-identified patient data from a United Kingdom National Health System COPD program were used. Datasets included biometric readings, alerts, and resource utilization. SPO2 was identified as a predictive classifier, with an optimal average threshold setting of 85-86%. BP and pulse were failed classifiers, and areas of design were identified that may improve utility and predictive capacity. Cost avoidance methodology was developed. RESULTS can be applied to health services planning decisions. Methods can be applied to system design and evaluation based on patient outcomes. This study validated the use of ROC in RM program evaluation.

Intensification of Diabetes Therapy and Time Until A1C Goal Attainment Among Patients With Newly Diagnosed Type 2 Diabetes Who Fail Metformin Monotherapy Within a Large Integrated Health System.

PubMed

Pantalone, Kevin M; Wells, Brian J; Chagin, Kevin M; Ejzykowicz, Flavia; Yu, Changhong; Milinovich, Alex; Bauman, Janine M; Kattan, Michael W; Rajpathak, Swapnil; Zimmerman, Robert S

2016-09-01

"Clinical inertia" has been used to describe the delay in the intensification of type 2 diabetes treatment among patients with poor glycemic control. Previous studies may have exaggerated the prevalence of clinical inertia by failing to adequately monitor drug dose changes and nonmedication interventions. This project evaluated the intensification of diabetes therapy and hemoglobin A1c (A1C) goal attainment among patients with newly diagnosed type 2 diabetes when metformin monotherapy failed. The electronic health record at Cleveland Clinic was used to identify patients with newly diagnosed type 2 diabetes between 2005 and 2013 who failed to reach the A1C goal after 3 months of metformin monotherapy. A time-dependent survival analysis was used to compare the time until A1C goal attainment in patients who received early intensification of therapy (within 6 months of metformin failure) or late intensification. The analysis was performed for A1C goals of 7% (n = 1,168), 7.5% (n = 679), and 8% (n = 429). Treatment was intensified early in 62%, 69%, and 72% of patients when poor glycemic control was defined as an A1C >7%, >7.5%, and >8%, respectively. The probability of undergoing an early intensification was greater the higher the A1C category. Time until A1C goal attainment was shorter among patients who received early intensification regardless of the A1C goal (all P < 0.05). A substantial number of patients with newly diagnosed type 2 diabetes fail to undergo intensification of therapy within 6 months of metformin monotherapy failure. Early intervention in patients when metformin monotherapy failed resulted in more rapid attainment of A1C goals. © 2016 by the American Diabetes Association.

NASA researchers in gold control room during an F-15 HiDEC flight

NASA Technical Reports Server (NTRS)

1993-01-01

NASA researchers monitor equipment in the mission control Gold room at the Dryden Flight Research Center, Edwards, California, during a flight of an F-15 Highly Integrated Digital Electronic Control (HIDEC) research aircraft. The system was developed on the F-15 to investigate and demonstrate methods of obtaining optimum aircraft performance. The major elements of HIDEC were a Digital Electronic Flight Control System (DEFCS), a Digital Electronic Engine Control (DEEC), an on-board general purpose computer, and an integrated architecture to allow all components to 'talk to each other.' Unlike standard F-15s, which have a mechanical and analog electronic flight control system, the HIDEC F-15 also had a dual-channel, fail-safe digital flight control system programmed in Pascal. It was linked to the Military Standard 1553B and a H009 data bus which tied all the other electronic systems together.

NASA researchers in gold control room during an F-15 HiDEC flight, John Orme and Gerard Schkolnik

NASA Technical Reports Server (NTRS)

1993-01-01

NASA researchers Gerard Schkolnik (left) and John Orme monitor equipment in the control room at the Dryden Flight Research Center, Edwards, California, during a flight of an F-15 Highly Integrated Digital Electronic Control (HIDEC) research aircraft. The system was developed on the F-15 to investigate and demonstrate methods of obtaining optimum aircraft performance. The major elements of HIDEC were a Digital Electronic Flight Control System (DEFCS), a Digital Electronic Engine Control (DEEC), an on-board general purpose computer, and an integrated architecture to allow all components to 'talk to each other.' Unlike standard F-15s, which have a mechanical and analog electronic flight control system, the HIDEC F-15 also had a dual-channel, fail-safe digital flight control system programmed in Pascal. It was linked to the Military Standard 1553B and a H009 data bus which tied all the other electronic systems together.

A single CD4 test with 250 cells/mm3 threshold predicts viral suppression in HIV-infected adults failing first-line therapy by clinical criteria.

PubMed

Gilks, Charles F; Walker, A Sarah; Munderi, Paula; Kityo, Cissy; Reid, Andrew; Katabira, Elly; Goodall, Ruth L; Grosskurth, Heiner; Mugyenyi, Peter; Hakim, James; Gibb, Diana M

2013-01-01

In low-income countries, viral load (VL) monitoring of antiretroviral therapy (ART) is rarely available in the public sector for HIV-infected adults or children. Using clinical failure alone to identify first-line ART failure and trigger regimen switch may result in unnecessary use of costly second-line therapy. Our objective was to identify CD4 threshold values to confirm clinically-determined ART failure when VL is unavailable. 3316 HIV-infected Ugandan/Zimbabwean adults were randomised to first-line ART with Clinically-Driven (CDM, CD4s measured but blinded) or routine Laboratory and Clinical Monitoring (LCM, 12-weekly CD4s) in the DART trial. CD4 at switch and ART failure criteria (new/recurrent WHO 4, single/multiple WHO 3 event; LCM: CD4<100 cells/mm(3)) were reviewed in 361 LCM, 314 CDM participants who switched over median 5 years follow-up. Retrospective VLs were available in 368 (55%) participants. Overall, 265/361 (73%) LCM participants failed with CD4<100 cells/mm(3); only 7 (2%) switched with CD4≥250 cells/mm(3), four switches triggered by WHO events. Without CD4 monitoring, 207/314 (66%) CDM participants failed with WHO 4 events, and 77(25%)/30(10%) with single/multiple WHO 3 events. Failure/switching with single WHO 3 events was more likely with CD4≥250 cells/mm(3) (28/77; 36%) (p = 0.0002). CD4 monitoring reduced switching with viral suppression: 23/187 (12%) LCM versus 49/181 (27%) CDM had VL<400 copies/ml at failure/switch (p<0.0001). Amongst CDM participants with CD4<250 cells/mm(3) only 11/133 (8%) had VL<400 copies/ml, compared with 38/48 (79%) with CD4≥250 cells/mm(3) (p<0.0001). Multiple, but not single, WHO 3 events predicted first-line ART failure. A CD4 threshold 'tiebreaker' of ≥250 cells/mm(3) for clinically-monitored patients failing first-line could identify ∼80% with VL<400 copies/ml, who are unlikely to benefit from second-line. Targeting CD4s to single WHO stage 3 'clinical failures' would particularly avoid premature, costly switch to second-line ART.

A Single CD4 Test with 250 Cells/Mm3 Threshold Predicts Viral Suppression in HIV-Infected Adults Failing First-Line Therapy by Clinical Criteria

PubMed Central

Munderi, Paula; Kityo, Cissy; Reid, Andrew; Katabira, Elly; Goodall, Ruth L.; Grosskurth, Heiner; Mugyenyi, Peter; Hakim, James; Gibb, Diana M.

2013-01-01

Background In low-income countries, viral load (VL) monitoring of antiretroviral therapy (ART) is rarely available in the public sector for HIV-infected adults or children. Using clinical failure alone to identify first-line ART failure and trigger regimen switch may result in unnecessary use of costly second-line therapy. Our objective was to identify CD4 threshold values to confirm clinically-determined ART failure when VL is unavailable. Methods 3316 HIV-infected Ugandan/Zimbabwean adults were randomised to first-line ART with Clinically-Driven (CDM, CD4s measured but blinded) or routine Laboratory and Clinical Monitoring (LCM, 12-weekly CD4s) in the DART trial. CD4 at switch and ART failure criteria (new/recurrent WHO 4, single/multiple WHO 3 event; LCM: CD4<100 cells/mm3) were reviewed in 361 LCM, 314 CDM participants who switched over median 5 years follow-up. Retrospective VLs were available in 368 (55%) participants. Results Overall, 265/361 (73%) LCM participants failed with CD4<100 cells/mm3; only 7 (2%) switched with CD4≥250 cells/mm3, four switches triggered by WHO events. Without CD4 monitoring, 207/314 (66%) CDM participants failed with WHO 4 events, and 77(25%)/30(10%) with single/multiple WHO 3 events. Failure/switching with single WHO 3 events was more likely with CD4≥250 cells/mm3 (28/77; 36%) (p = 0.0002). CD4 monitoring reduced switching with viral suppression: 23/187 (12%) LCM versus 49/181 (27%) CDM had VL<400 copies/ml at failure/switch (p<0.0001). Amongst CDM participants with CD4<250 cells/mm3 only 11/133 (8%) had VL<400copies/ml, compared with 38/48 (79%) with CD4≥250 cells/mm3 (p<0.0001). Conclusion Multiple, but not single, WHO 3 events predicted first-line ART failure. A CD4 threshold ‘tiebreaker’ of ≥250 cells/mm3 for clinically-monitored patients failing first-line could identify ∼80% with VL<400 copies/ml, who are unlikely to benefit from second-line. Targeting CD4s to single WHO stage 3 ‘clinical failures’ would particularly avoid premature, costly switch to second-line ART. PMID:23437399

A reliable sewage quality abnormal event monitoring system.

PubMed

Li, Tianling; Winnel, Melissa; Lin, Hao; Panther, Jared; Liu, Chang; O'Halloran, Roger; Wang, Kewen; An, Taicheng; Wong, Po Keung; Zhang, Shanqing; Zhao, Huijun

2017-09-15

With closing water loop through purified recycled water, wastewater becomes a part of source water, requiring reliable wastewater quality monitoring system (WQMS) to manage wastewater source and mitigate potential health risks. However, the development of reliable WQMS is fatally constrained by severe contamination and biofouling of sensors due to the hostile analytical environment of wastewaters, especially raw sewages, that challenges the limit of existing sensing technologies. In this work, we report a technological solution to enable the development of WQMS for real-time abnormal event detection with high reliability and practicality. A vectored high flow hydrodynamic self-cleaning approach and a dual-sensor self-diagnostic concept are adopted for WQMS to effectively encounter vital sensor failing issues caused by contamination and biofouling and ensure the integrity of sensing data. The performance of the WQMS has been evaluated over a 3-year trial period at different sewage catchment sites across three Australian states. It has demonstrated that the developed WQMS is capable of continuously operating in raw sewage for a prolonged period up to 24 months without maintenance and failure, signifying the high reliability and practicality. The demonstrated WQMS capability to reliably acquire real-time wastewater quality information leaps forward the development of effective wastewater source management system. The reported self-cleaning and self-diagnostic concepts should be applicable to other online water quality monitoring systems, opening a new way to encounter the common reliability and stability issues caused by sensor contamination and biofouling. Copyright © 2017 Elsevier Ltd. All rights reserved.

Isolating the impact of septic systems on fecal pollution in streams of suburban watersheds in Georgia, United States.

PubMed

Sowah, Robert A; Habteselassie, Mussie Y; Radcliffe, David E; Bauske, Ellen; Risse, Mark

2017-01-01

The presence of multiple sources of fecal pollution at the watershed level presents challenges to efforts aimed at identifying the influence of septic systems. In this study multiple approaches including targeted sampling and monitoring of host-specific Bacteroidales markers were used to identify the impact of septic systems on microbial water quality. Twenty four watersheds with septic density ranging from 8 to 373 septic units/km 2 were monitored for water quality under baseflow conditions over a 3-year period. The levels of the human-associated HF183 marker, as well as total and ruminant Bacteroidales, were quantified using quantitative polymerase chain reaction. Human-associated Bacteroidales yield was significantly higher in high density watersheds compared to low density areas and was negatively correlated (r = -0.64) with the average distance of septic systems to streams in the spring season. The human marker was also positively correlated with the total Bacteroidales marker, suggesting that the human source input was a significant contributor to total fecal pollution in the study area. Multivariable regression analysis indicates that septic systems, along with forest cover, impervious area and specific conductance could explain up to 74% of the variation in human fecal pollution in the spring season. The results suggest septic system impact through contributions to groundwater recharge during baseflow or failing septic system input, especially in areas with >87 septic units/km 2 . This study supports the use of microbial source tracking approaches along with traditional fecal indicator bacteria monitoring and land use characterization in a tiered approach to isolate the influence of septic systems on water quality in mixed-use watersheds. Copyright © 2016 Elsevier Ltd. All rights reserved.

Small Schools Science Curriculum, K-3: Reading, Language Arts, Mathematics, Science, Social Studies. Scope, Objectives, Activities, Resources, Monitoring Procedures.

ERIC Educational Resources Information Center

Hartl, David, Ed.; And Others

Learning objectives and suggested activities, monitoring procedures and resources for the Washington K-3 Small Schools Science Curriculum are based on the rationale that "young children need the opportunity to observe, classify, predict, test ideas again and again in a variety of contexts, ask questions, explain, discuss ideas, fail, and succeed.…

Testing the Importance of Individual Growth Curves in Predicting Performance on a High-Stakes Reading Comprehension Test in Florida. REL 2014-006

ERIC Educational Resources Information Center

Petscher, Yaacov; Kershaw, Sarah; Koon, Sharon; Foorman, Barbara R.

2014-01-01

Districts and schools use progress monitoring to assess student progress, to identify students who fail to respond to intervention, and to further adapt instruction to student needs. Researchers and practitioners often use progress monitoring data to estimate student achievement growth (slope) and evaluate changes in performance over time for…

Making real-time reactive systems reliable

NASA Technical Reports Server (NTRS)

Marzullo, Keith; Wood, Mark

1990-01-01

A reactive system is characterized by a control program that interacts with an environment (or controlled program). The control program monitors the environment and reacts to significant events by sending commands to the environment. This structure is quite general. Not only are most embedded real time systems reactive systems, but so are monitoring and debugging systems and distributed application management systems. Since reactive systems are usually long running and may control physical equipment, fault tolerance is vital. The research tries to understand the principal issues of fault tolerance in real time reactive systems and to build tools that allow a programmer to design reliable, real time reactive systems. In order to make real time reactive systems reliable, several issues must be addressed: (1) How can a control program be built to tolerate failures of sensors and actuators. To achieve this, a methodology was developed for transforming a control program that references physical value into one that tolerates sensors that can fail and can return inaccurate values; (2) How can the real time reactive system be built to tolerate failures of the control program. Towards this goal, whether the techniques presented can be extended to real time reactive systems is investigated; and (3) How can the environment be specified in a way that is useful for writing a control program. Towards this goal, whether a system with real time constraints can be expressed as an equivalent system without such constraints is also investigated.

Evaluation of the XSENS Force Shoe on ISS

NASA Technical Reports Server (NTRS)

Hanson, A. M.; Peters, B. T.; Newby, N.; Ploutz-Snyder, L

2014-01-01

The Advanced Resistive Exercise Device (ARED) offers crewmembers a wide range of resistance exercises but does not provide any type of load monitoring; any load data received are based on crew self-report of dialed in load. This lack of real-time ARED load monitoring severely limits research analysis. To address this issue, portable load monitoring technologies are being evaluated to act as a surrogate to ARED's failed instrumentation. The XSENS ForceShoe"TM" is a commercial portable load monitoring tool, and performed well in ground tests. The ForceShoe "TM" was recently deployed on the International Space Station (ISS), and is being evaluated as a tool to monitor ARED loads.

Infusion-line pressure as a real-time monitor of convection-enhanced delivery in pre-clinical models.

PubMed

Lam, Miu Fei; Foo, Stacy W L; Thomas, Meghan G; Lind, Christopher R P

2014-01-15

Acute convection-enhanced delivery (CED) is a neurosurgical delivery technique that allows for precise and uniform distribution of an infusate to a brain structure. It remains experimental due to difficulties in ensuring successful delivery. Real-time monitoring is able to provide immediate feedback on cannula placement, infusate distribution, and if the infusion is proceeding as planned or is failing due to reflux or catheter obstruction. Pressure gradient is the driving force behind CED, with the infusion pressure being directly proportional to the flow-rate. The aim of this study was to assess the feasibility of using infusion-line pressure profiling to distinguish in real-time between succeeding and failing CED infusions. To do so we delivered cresyl violet dye at 0.5, 1.0 and 2.0 μl/min via CED in vitro using 0.6% agarose gel and in vivo to the rat striatum. Infusions that failed in agarose gel models could only be differentiated late during the procedures. In the rat in vivo model, the infusion-line profiles of obstructed infusions were not distinctive from those of successful infusions. Intraoperative magnetic resonance imaging (MRI) is used for real-time visualisation of cannula placement and infusate distribution. Particularly for animal pre-clinical work, it would be advantageous to supplement MRI with a cheap, accessible technique to monitor infusions and provide a real-time measure of infusion success or failure. Infusion-line pressure monitoring was of limited value in identifying successful CED with small volume infusions, whilst its utility for large volume infusion remains unknown. Crown Copyright © 2013. Published by Elsevier B.V. All rights reserved.

Development of Laser Scanner for Full Cross-Sectional Deformation Monitoring of Underground Gateroads

PubMed Central

Yang, Qianlong; Zhang, Zhenyu; Liu, Xiaoqian; Ma, Shuqi

2017-01-01

The deformation of underground gateroads tends to be asymmetric and complex. Traditional instrumentation fails to accurately and conveniently monitor the full cross-sectional deformation of underground gateroads. Here, a full cross-sectional laser scanner was developed, together with a visualization software package. The developed system used a polar coordinate measuring method and the full cross-sectional measurement was shown by 360° rotation of a laser sensor driven by an electrical motor. Later on, the potential impact of gateroad wall flatness, roughness, and geometrical profile, as well as coal dust environment on the performance of the developed laser scanner will be evaluated. The study shows that high-level flatness is favorable in the application of the developed full cross-sectional deformation monitoring system. For a smooth surface of gateroad, the sensor cannot receive reflected light when the incidence angle of laser beam is large, causing data loss. Conversely, the roughness surface shows its nature as the diffuse reflection light can be received by the sensor. With regards to coal dust in the measurement environment, fine particles of floating coal dust in the air can lead to the loss of measurement data to some extent, due to scattering of the laser beam. PMID:28590449

A Comprehensive Reliability Methodology for Assessing Risk of Reusing Failed Hardware Without Corrective Actions with and Without Redundancy

NASA Technical Reports Server (NTRS)

Putcha, Chandra S.; Mikula, D. F. Kip; Dueease, Robert A.; Dang, Lan; Peercy, Robert L.

1997-01-01

This paper deals with the development of a reliability methodology to assess the consequences of using hardware, without failure analysis or corrective action, that has previously demonstrated that it did not perform per specification. The subject of this paper arose from the need to provide a detailed probabilistic analysis to calculate the change in probability of failures with respect to the base or non-failed hardware. The methodology used for the analysis is primarily based on principles of Monte Carlo simulation. The random variables in the analysis are: Maximum Time of Operation (MTO) and operation Time of each Unit (OTU) The failure of a unit is considered to happen if (OTU) is less than MTO for the Normal Operational Period (NOP) in which this unit is used. NOP as a whole uses a total of 4 units. Two cases are considered. in the first specialized scenario, the failure of any operation or system failure is considered to happen if any of the units used during the NOP fail. in the second specialized scenario, the failure of any operation or system failure is considered to happen only if any two of the units used during the MOP fail together. The probability of failure of the units and the system as a whole is determined for 3 kinds of systems - Perfect System, Imperfect System 1 and Imperfect System 2. in a Perfect System, the operation time of the failed unit is the same as that of the MTO. In an Imperfect System 1, the operation time of the failed unit is assumed as 1 percent of the MTO. In an Imperfect System 2, the operation time of the failed unit is assumed as zero. in addition, simulated operation time of failed units is assumed as 10 percent of the corresponding units before zero value. Monte Carlo simulation analysis is used for this study. Necessary software has been developed as part of this study to perform the reliability calculations. The results of the analysis showed that the predicted change in failure probability (P(sub F)) for the previously failed units is as high as 49 percent above the baseline (perfect system) for the worst case. The predicted change in system P(sub F) for the previously failed units is as high as 36% for single unit failure without any redundancy. For redundant systems, with dual unit failure, the predicted change in P(sub F) for the previously failed units is as high as 16%. These results will help management to make decisions regarding the consequences of using previously failed units without adequate failure analysis or corrective action.

30 CFR 77.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Fail safe ground check circuits on high-voltage... WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.803 Fail safe ground check..., resistance grounded systems shall include a fail safe ground check circuit or other no less effective device...

30 CFR 77.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fail safe ground check circuits on high-voltage... WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.803 Fail safe ground check..., resistance grounded systems shall include a fail safe ground check circuit or other no less effective device...

30 CFR 77.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Fail safe ground check circuits on high-voltage... WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.803 Fail safe ground check..., resistance grounded systems shall include a fail safe ground check circuit or other no less effective device...

30 CFR 77.803 - Fail safe ground check circuits on high-voltage resistance grounded systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Fail safe ground check circuits on high-voltage... WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.803 Fail safe ground check..., resistance grounded systems shall include a fail safe ground check circuit or other no less effective device...

Formal Verification of Safety Properties for Aerospace Systems Through Algorithms Based on Exhaustive State-Space Exploration

NASA Technical Reports Server (NTRS)

Ciardo, Gianfranco

2004-01-01

The Runway Safety Monitor (RSM) designed by Lockheed Martin is part of NASA's effort to reduce aviation accidents. We developed a Petri net model of the RSM protocol and used the model checking functions of our tool SMART to investigate a number of safety properties in RSM. To mitigate the impact of state-space explosion, we built a highly discretized model of the system, obtained by partitioning the monitored runway zone into a grid of smaller volumes and by considering scenarios involving only two aircraft. The model also assumes that there are no communication failures, such as bad input from radar or lack of incoming data, thus it relies on a consistent view of reality by all participants. In spite of these simplifications, we were able to expose potential problems in the RSM conceptual design. Our findings were forwarded to the design engineers, who undertook corrective action. Additionally, the results stress the efficiency attained by the new model checking algorithms implemented in SMART, and demonstrate their applicability to real-world systems. Attempts to verify RSM with NuSMV and SPIN have failed due to excessive memory consumption.

45 CFR 95.635 - Disallowance of Federal financial participation for automated systems that fail to comply...

Code of Federal Regulations, 2013 CFR

2013-10-01

... 45 Public Welfare 1 2013-10-01 2013-10-01 false Disallowance of Federal financial participation for automated systems that fail to comply substantially with requirements. 95.635 Section 95.635... participation for automated systems that fail to comply substantially with requirements. (a) Federal financial...

45 CFR 95.635 - Disallowance of Federal financial participation for automated systems that fail to comply...

Code of Federal Regulations, 2012 CFR

2012-10-01

... 45 Public Welfare 1 2012-10-01 2012-10-01 false Disallowance of Federal financial participation for automated systems that fail to comply substantially with requirements. 95.635 Section 95.635... participation for automated systems that fail to comply substantially with requirements. (a) Federal financial...

45 CFR 95.635 - Disallowance of Federal financial participation for automated systems that fail to comply...

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 1 2014-10-01 2014-10-01 false Disallowance of Federal financial participation for automated systems that fail to comply substantially with requirements. 95.635 Section 95.635... participation for automated systems that fail to comply substantially with requirements. (a) Federal financial...

45 CFR 95.635 - Disallowance of Federal financial participation for automated systems that fail to comply...

Code of Federal Regulations, 2011 CFR

2011-10-01

... 45 Public Welfare 1 2011-10-01 2011-10-01 false Disallowance of Federal financial participation for automated systems that fail to comply substantially with requirements. 95.635 Section 95.635... participation for automated systems that fail to comply substantially with requirements. (a) Federal financial...

Integrating remotely sensed fires for predicting deforestation for REDD.

PubMed

Armenteras, Dolors; Gibbes, Cerian; Anaya, Jesús A; Dávalos, Liliana M

2017-06-01

Fire is an important tool in tropical forest management, as it alters forest composition, structure, and the carbon budget. The United Nations program on Reducing Emissions from Deforestation and Forest Degradation (REDD+) aims to sustainably manage forests, as well as to conserve and enhance their carbon stocks. Despite the crucial role of fire management, decision-making on REDD+ interventions fails to systematically include fires. Here, we address this critical knowledge gap in two ways. First, we review REDD+ projects and programs to assess the inclusion of fires in monitoring, reporting, and verification (MRV) systems. Second, we model the relationship between fire and forest for a pilot site in Colombia using near-real-time (NRT) fire monitoring data derived from the Moderate Resolution Imaging Spectroradiometer (MODIS). The literature review revealed fire remains to be incorporated as a key component of MRV systems. Spatially explicit modeling of land use change showed the probability of deforestation declined sharply with increasing distance to the nearest fire the preceding year (multi-year model area under the curve [AUC] 0.82). Deforestation predictions based on the model performed better than the official REDD early-warning system. The model AUC for 2013 and 2014 was 0.81, compared to 0.52 for the early-warning system in 2013 and 0.68 in 2014. This demonstrates NRT fire monitoring is a powerful tool to predict sites of forest deforestation. Applying new, publicly available, and open-access NRT fire data should be an essential element of early-warning systems to detect and prevent deforestation. Our results provide tools for improving both the current MRV systems, and the deforestation early-warning system in Colombia. © 2017 by the Ecological Society of America.

Material handling robot system for flow-through storage applications

NASA Astrophysics Data System (ADS)

Dill, James F.; Candiloro, Brian; Downer, James; Wiesman, Richard; Fallin, Larry; Smith, Ron

1999-01-01

This paper describes the design, development and planned implementation of a system of mobile robots for use in flow through storage applications. The robots are being designed with on-board embedded controls so that they can perform their tasks as semi-autonomous workers distributed within a centrally controlled network. On the storage input side, boxes will be identified by bar-codes and placed into preassigned flow through bins. On the shipping side, orders will be forwarded to the robots from a central order processing station and boxes will be picked from designated storage bins following proper sequencing to permit direct loading into trucks for shipping. Because of the need to maintain high system availability, a distributed control strategy has been selected. When completed, the system will permit robots to be dynamically reassigned responsibilities if an individual unit fails. On-board health diagnostics and condition monitoring will be used to maintain high reliability of the units.

On the security of a dynamic ID-based authentication scheme for telecare medical information systems.

PubMed

Lin, Han-Yu

2013-04-01

Telecare medical information systems (TMISs) are increasingly popular technologies for healthcare applications. Using TMISs, physicians and caregivers can monitor the vital signs of patients remotely. Since the database of TMISs stores patients' electronic medical records (EMRs), only authorized users should be granted the access to this information for the privacy concern. To keep the user anonymity, recently, Chen et al. proposed a dynamic ID-based authentication scheme for telecare medical information system. They claimed that their scheme is more secure and robust for use in a TMIS. However, we will demonstrate that their scheme fails to satisfy the user anonymity due to the dictionary attacks. It is also possible to derive a user password in case of smart card loss attacks. Additionally, an improved scheme eliminating these weaknesses is also presented.

Minimization of the energy loss of nuclear power plants in case of partial in-core monitoring system failure

NASA Astrophysics Data System (ADS)

Zagrebaev, A. M.; Ramazanov, R. N.; Lunegova, E. A.

2017-01-01

In this paper we consider the optimization problem minimize of the energy loss of nuclear power plants in case of partial in-core monitoring system failure. It is possible to continuation of reactor operation at reduced power or total replacement of the channel neutron measurements, requiring shutdown of the reactor and the stock of detectors. This article examines the reconstruction of the energy release in the core of a nuclear reactor on the basis of the indications of height sensors. The missing measurement information can be reconstructed by mathematical methods, and replacement of the failed sensors can be avoided. It is suggested that a set of ‘natural’ functions determined by means of statistical estimates obtained from archival data be constructed. The procedure proposed makes it possible to reconstruct the field even with a significant loss of measurement information. Improving the accuracy of the restoration of the neutron flux density in partial loss of measurement information to minimize the stock of necessary components and the associated losses.

Integrating mHealth in Oncology: Experience in the Province of Trento.

PubMed

Galligioni, Enzo; Piras, Enrico Maria; Galvagni, Michele; Eccher, Claudio; Caramatti, Silvia; Zanolli, Daniela; Santi, Jonni; Berloffa, Flavio; Dianti, Marco; Maines, Francesca; Sannicolò, Mirella; Sandri, Marco; Bragantini, Lara; Ferro, Antonella; Forti, Stefano

2015-05-13

The potential benefits of the introduction of electronic and mobile health (mHealth) information technologies, to support the safe delivery of intravenous chemotherapy or oral anticancer therapies, could be exponential in the context of a highly integrated computerized system. Here we describe a safe therapy mobile (STM) system for the safe delivery of intravenous chemotherapy, and a home monitoring system for monitoring and managing toxicity and improving adherence in patients receiving oral anticancer therapies at home. The STM system is fully integrated with the electronic oncological patient record. After the prescription of chemotherapy, specific barcodes are automatically associated with the patient and each drug, and a bedside barcode reader checks the patient, nurse, infusion bag, and drug sequence in order to trace the entire administration process, which is then entered in the patient's record. The usability and acceptability of the system was investigated by means of a modified questionnaire administered to nurses. The home monitoring system consists of a mobile phone or tablet diary app, which allows patients to record their state of health, the medications taken, their side effects, and a Web dashboard that allows health professionals to check the patient data and monitor toxicity and treatment adherence. A built-in rule-based alarm module notifies health care professionals of critical conditions. Initially developed for chronic patients, the system has been subsequently customized in order to monitor home treatments with capecitabine or sunitinib in cancer patients (Onco-TreC). The STM system never failed to match the patient/nurse/drug sequence association correctly, and proved to be accurate and reliable in tracing and recording the entire administration process. The questionnaires revealed that the users were generally satisfied and had a positive perception of the system's usefulness and ease of use, and the quality of their working lives. The pilot studies with the home monitoring system with 43 chronic patients have shown that the approach is reliable and useful for clinicians and patients, but it is also necessary to pay attention to the expectations that mHealth solutions may raise in users. The Onco-TreC version has been successfully laboratory tested, and is now ready for validation. The STM and Onco-TreC systems are fully integrated with our complex and composite information system, which guarantees privacy, security, interoperability, and real-time communications between patients and health professionals. They need to be validated in order to confirm their positive contribution to the safer administration of anticancer drugs.

Device monitoring strategies in acute heart failure syndromes.

PubMed

Samara, Michael A; Tang, W H Wilson

2011-09-01

Acute heart failure syndromes (AHFS) represent the most common discharge diagnoses in adults over age 65 and translate into dramatically increased heart failure-associated morbidity and mortality. Conventional approaches to the early detection of pulmonary and systemic congestion have been shown to be of limited sensitivity. Despite their proven efficacy, disease management and structured telephone support programs have failed to achieve widespread use in part due to their resource intensiveness and reliance upon motivated patients. While once thought to hold great promise, results from recent prospective studies on telemonitoring strategies have proven disappointing. Implantable devices with their capacity to monitor electrophysiologic and hemodynamic parameters over long periods of time and with minimal reliance on patient participation may provide solutions to some of these problems. Conventional electrophysiologic parameters and intrathoracic impedance data are currently available in the growing population of heart failure patients with equipped devices. A variety of implantable hemodynamic monitors are currently under investigation. How best to integrate these devices into a systematic approach to the management of patients before, during, and after AHFS is yet to be established.

On the ability of consumer electronics microphones for environmental noise monitoring.

PubMed

Van Renterghem, Timothy; Thomas, Pieter; Dominguez, Frederico; Dauwe, Samuel; Touhafi, Abdellah; Dhoedt, Bart; Botteldooren, Dick

2011-03-01

The massive production of microphones for consumer electronics, and the shift from dedicated processing hardware to PC-based systems, opens the way to build affordable, extensive noise measurement networks. Applications include e.g. noise limit and urban soundscape monitoring, and validation of calculated noise maps. Microphones are the critical components of such a network. Therefore, in a first step, some basic characteristics of 8 microphones, distributed over a wide range of price classes, were measured in a standardized way in an anechoic chamber. In a next step, a thorough evaluation was made of the ability of these microphones to be used for environmental noise monitoring. This was done during a continuous, half-year lasting outdoor experiment, characterized by a wide variety of meteorological conditions. While some microphones failed during the course of this test, it was shown that it is possible to identify cheap microphones that highly correlate to the reference microphone during the full test period. When the deviations are expressed in total A-weighted (road traffic) noise levels, values of less than 1 dBA are obtained, in excess to the deviation amongst reference microphones themselves.

12 CFR 202.16 - Enforcement, penalties and liabilities.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) and 706(a) and (b) of the Act provide that any creditor that fails to comply with a requirement.... If a creditor inadvertently obtains the monitoring information regarding the ethnicity, race, and sex...

12 CFR 202.16 - Enforcement, penalties and liabilities.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) and 706(a) and (b) of the Act provide that any creditor that fails to comply with a requirement.... If a creditor inadvertently obtains the monitoring information regarding the ethnicity, race, and sex...

Testing the Importance of Individual Growth Curves in Predicting Performance on a High-Stakes Reading Comprehension Test in Florida. Summary. REL 2014-006

ERIC Educational Resources Information Center

Petscher, Yaacov; Kershaw, Sarah; Koon, Sharon; Foorman, Barbara R.

2014-01-01

Districts and schools use progress monitoring to assess student progress, to identify students who fail to respond to intervention, and to further adapt instruction to student needs. Researchers and practitioners often use progress monitoring data to estimate student achievement growth (slope) and evaluate changes in performance over time for…

Leveraging Educational, Research and Facility Expertise to Improve Global Seismic Monitoring: Preparing a Guide on Sustainable Networks

NASA Astrophysics Data System (ADS)

Nybade, A.; Aster, R.; Beck, S.; Ekstrom, G.; Fischer, K.; Lerner-Lam, A.; Meltzer, A.; Sandvol, E.; Willemann, R. J.

2008-12-01

Building a sustainable earthquake monitoring system requires well-informed cooperation between commercial companies that manufacture components or deliver complete systems and the government or other agencies that will be responsible for operating them. Many nations or regions with significant earthquake hazard lack the financial, technical, and human resources to establish and sustain permanent observatory networks required to return the data needed for hazard mitigation. Government agencies may not be well- informed about the short-term and long-term challenges of managing technologically advanced monitoring systems, much less the details of how they are built and operated. On the relatively compressed time scale of disaster recovery efforts, it can be difficult to find a reliable, disinterested source of information, without which government agencies may be dependent on partial information. If system delivery fails to include sufficient development of indigenous expertise, the performance of local and regional networks may decline quickly, and even data collected during an early high-performance period may be degraded or lost. Drawing on unsurpassed educational capabilities of its members working in close cooperation with its facility staff, IRIS is well prepared to contribute to sustainability through a wide variety of training and service activities that further promote standards for network installation, data exchange protocols, and free and open access to data. Members of the Consortium and staff of its Core Programs together could write a guide on decisions about network design, installation and operation. The intended primary audience would be government officials seeking to understand system requirements, the acquisition and installation process, and the expertise needed operate a system. The guide would cover network design, procurement, set-up, data use and archiving. Chapters could include advice on network data processing, archiving data (including information on the value of standards), installing and servicing stations, building a data processing and management center (including information on evaluating bids), using results from earthquake monitoring, and sustaining an earthquake monitoring system. Appendices might include profiles of well-configured and well- run networks and sample RFPs. Establishing permanent networks could provide a foundation for international research and educational collaborations and critical new data for imaging Earth structure while supporting scientific capacity building and strengthening hazard monitoring around the globe.

[The Hospital Information System of the Brazilian National Unified Health System: a preliminary evaluation of performance in monitoring RhD hemolytic disease of the newborn].

PubMed

Lobato, Gustavo; Reichenheim, Michael Eduardo; Coeli, Claudia Medina

2008-03-01

This study aimed to evaluate the adequacy of the Hospital Information System of the National Unified Health System (SIH-SUS) in identifying cases of RhD hemolytic disease of the newborn (HDN) at the Fernandes Figueira Institute (IFF/FIOCRUZ) from 1998 to 2003. Neonatal records, data from the Medical Archives, and AIH (Hospital Admissions Authorization Form) data consolidated in the SIH-SUS were analyzed. Cases were identified according to the following fields: principal diagnosis, secondary diagnosis, and procedure performed. During the period studied, 194 cases of HDN were diagnosed. The Medical Archives registered 148 newborns with HDN, however only 147 AIHs were issued and 145 consolidated in the SIH-SUS. Among these 145 cases, 84 cited HDN as the principal diagnosis, while secondary diagnosis identified 38 additional cases and the procedures performed failed to identify any further cases. Thus, the SIH-SUS identified only 122 (62.9%) of the 194 cases of HDN treated at the IFF/FIOCRUZ. Although it is necessary to evaluate other units, the SIH-SUS does not appear to be reliable for monitoring HDN. Additional studies are essential for employing secondary administrative data in the context of epidemiological surveillance.

Resilient Practices in Maintaining Safety of Health Information Technologies

PubMed Central

Ash, Joan S.; Sittig, Dean F.; Singh, Hardeep

2014-01-01

Electronic health record systems (EHRs) can improve safety and reliability of health care, but they can also introduce new vulnerabilities by failing to accommodate changes within a dynamic EHR-enabled health care system. Continuous assessment and improvement is thus essential for achieving resilience in EHR-enabled health care systems. Given the rapid adoption of EHRs by many organizations that are still early in their experiences with EHR safety, it is important to understand practices for maintaining resilience used by organizations with a track record of success in EHR use. We conducted interviews about safety practices with 56 key informants (including information technology managers, chief medical information officers, physicians, and patient safety officers) at two large health care systems recognized as leaders in EHR use. We identified 156 references to resilience-related practices from 41 informants. Framework analysis generated five categories of resilient practices: (a) sensitivity to dynamics and interdependencies affecting risks, (b) basic monitoring and responding practices, (c) management of practices and resources for monitoring and responding, (d) sensitivity to risks beyond the horizon, and (e) reflecting on risks with the safety and quality control process itself. The categories reflect three functions that facilitate resilience: reflection, transcending boundaries, and involving sharp-end practitioners in safety management. PMID:25866492

Conductive surge testing of circuits and systems

NASA Technical Reports Server (NTRS)

Richman, P.

1980-01-01

Techniques are given for conductive surge testing of powered electronic equipment. The correct definitions of common and normal mode are presented. Testing requires not only spike-surge generators with a suitable range of open-circuit voltage and short-circuit current waveshapes, but also appropriate means, termed couplers, for connecting test surges to the equipment under test. Key among coupler design considerations is minimization of fail positives resulting from reduction in delivered surge energy due to the coupler. Back-filters and the lines on which they are necessary, are considered as well as ground-fault and ground potential rise. A method for monitoring delivered and resulting surge waves is mentioned.

Functional bacteria and process metabolism of the Denitrifying Sulfur conversion-associated Enhanced Biological Phosphorus Removal (DS-EBPR) system: An investigation by operating the system from deterioration to restoration.

PubMed

Guo, Gang; Wu, Di; Hao, Tianwei; Mackey, Hamish Robert; Wei, Li; Wang, Haiguang; Chen, Guanghao

2016-05-15

A sulfur conversion-associated Enhanced Biological Phosphorus (P) Removal (EBPR) system is being developed to cater for the increasing needs to treat saline/brackish wastewater resulting from seawater intrusion into groundwater and sewers and frequent use of sulfate coagulants during drinking water treatment, as well as to meet the demand for eutrophication control in warm climate regions. However, the major functional bacteria and metabolism in this emerging biological nutrient removal system are still poorly understood. This study was thus designed to explore the functional microbes and metabolism in this new EBPR system by manipulating the deterioration, failure and restoration of a lab-scale system. This was achieved by changing the mixed liquor suspended solids (MLSS) concentration to monitor and evaluate the relationships among sulfur conversion (including sulfate reduction and sulfate production), P removal, variation in microbial community structures, and stoichiometric parameters. The results show that the stable Denitrifying Sulfur conversion-associated EBPR (DS-EBPR) system was enriched by sulfate-reducing bacteria (SRB) and sulfide-oxidizing bacteria (SOB). These bacteria synergistically participated in this new EBPR process, thereby inducing an appropriate level of sulfur conversion crucial for achieving a stable DS-EBPR performance, i.e. maintaining sulfur conversion intensity at 15-40 mg S/L, corresponding to an optimal sludge concentration of 6.5 g/L. This range of sulfur conversion favors microbial community competition and various energy flows from internal polymers (i.e. polysulfide or elemental sulfur (poly-S(2-)/S(0)) and poly-β-hydroxyalkanoates (PHA)) for P removal. If this range was exceeded, the system might deteriorate or even fail due to enrichment of glycogen-accumulating organisms (GAOs). Four methods of restoring the failed system were investigated: increasing the sludge concentration, lowering the salinity or doubling the COD loading, non of which restored SRB and SOB activities for DS-EBPR; only the final novel approach of adding 25 ± 5 mg S/L of external sulfide into the reactor at the beginning of the anoxic phase could efficiently restore the DS-EBPR system from failure. The present study represents a step towards understanding the DS-EBPR metabolism and provides an effective remedial measure for recovering a deteriorating or failed DS-EBPR system. Copyright © 2016 Elsevier Ltd. All rights reserved.

The effects of monitoring environment on problem-solving performance.

PubMed

Laird, Brian K; Bailey, Charles D; Hester, Kim

2018-01-01

While effective and efficient solving of everyday problems is important in business domains, little is known about the effects of workplace monitoring on problem-solving performance. In a laboratory experiment, we explored the monitoring environment's effects on an individual's propensity to (1) establish pattern solutions to problems, (2) recognize when pattern solutions are no longer efficient, and (3) solve complex problems. Under three work monitoring regimes-no monitoring, human monitoring, and electronic monitoring-114 participants solved puzzles for monetary rewards. Based on research related to worker autonomy and theory of social facilitation, we hypothesized that monitored (versus non-monitored) participants would (1) have more difficulty finding a pattern solution, (2) more often fail to recognize when the pattern solution is no longer efficient, and (3) solve fewer complex problems. Our results support the first two hypotheses, but in complex problem solving, an interaction was found between self-assessed ability and the monitoring environment.

"Teaching Case": ComprehensiveCare and the Stalled Adoption of an Electronic Health Records System: IT Governance and Employee Succession

ERIC Educational Resources Information Center

Gomillion, David L.

2017-01-01

ComprehensiveCare, a multi-specialty healthcare organization, struggles to implement Electronic Health Records. The first adoption failed outright because the customizations made the system unusable. The second attempted adoption has not officially failed yet, but the system fails to live up to the expectations. It lingers on the edge of…

Implementation science for ambulatory care safety: a novel method to develop context-sensitive interventions to reduce quality gaps in monitoring high-risk patients.

PubMed

McDonald, Kathryn M; Su, George; Lisker, Sarah; Patterson, Emily S; Sarkar, Urmimala

2017-06-24

Missed evidence-based monitoring in high-risk conditions (e.g., cancer) leads to delayed diagnosis. Current technological solutions fail to close this safety gap. In response, we aim to demonstrate a novel method to identify common vulnerabilities across clinics and generate attributes for context-flexible population-level monitoring solutions for widespread implementation to improve quality. Based on interviews with staff in otolaryngology, pulmonary, urology, breast, and gastroenterology clinics at a large urban publicly funded health system, we applied journey mapping to co-develop a visual representation of how patients are monitored for high-risk conditions. Using a National Academies framework and context-sensitivity theory, we identified common systems vulnerabilities and developed preliminary concepts for improving the robustness for monitoring patients with high-risk conditions ("design seeds" for potential solutions). Finally, we conducted a face validity and prioritization assessment of the design seeds with the original interviewees. We identified five high-risk situations for potentially consequential diagnostic delays arising from suboptimal patient monitoring. All situations related to detection of cancer (head and neck, lung, prostate, breast, and colorectal). With clinic participants we created 5 journey maps, each representing specialty clinic workflow directed at evidence-based monitoring. System vulnerabilities common to the different clinics included challenges with: data systems, communications handoffs, population-level tracking, and patient activities. Clinic staff ranked 13 design seeds (e.g., keep patient list up to date, use triggered notifications) addressing these vulnerabilities. Each design seed has unique evaluation criteria for the usefulness of potential solutions developed from the seed. We identified and ranked 13 design seeds that characterize situations that clinicians described 'wake them up at night', and thus could reduce their anxiety, save time, and improve monitoring of high-risk patients. We anticipate that the design seed approach promotes robust and context-sensitive solutions to safety and quality problems because it provides a human-centered link between the experienced problem and various solutions that can be tested for viability. The study also demonstrates a novel integration of industrial and human factors methods (journey mapping, process tracing and design seeds) linked to implementation theory for use in designing interventions that anticipate and reduce implementation challenges.

Uterine Artery Embolization Combined with Local Methotrexate and Systemic Methotrexate for Treatment of Cesarean Scar Pregnancy with Different Ultrasonographic Pattern

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lian Fan; Wang Yu, E-mail: wyfishking@hotmail.com; Chen Wei

Purpose: This study was designed to compare the effectiveness of systemic methotrexate (MTX) with uterine artery embolization (UAE) combined with local MTX for the treatment of cesarean scar pregnancy (CSP) with different ultrasonographic pattern, and to indicate the preferable therapy in CSP patients. Methods: The results of 21 CSP cases were reviewed. All subjects were initially administrated with systemic MTX (50 mg/m{sup 2} body surface area). UAE combined with local MTX was added to the patients who had failed systemic MTX. The transvaginal ultrasonography data were retrospectively assessed, and two different ultrasonographic patterns were found: surface implantation and deep implantationmore » of amniotic sac. The management and its effectiveness for patients with the two ultrasonographic patterns were studied retrospectively. Ultrasound scan and serum {beta}-hCG were monitored during follow-up. Data were analyzed with the Student's t test. Results: Nine patients were successfully treated with systemic MTX. The remaining 12 cases were successfully treated with additional UAE combined with local MTX. According to the classification by Vial et al. of CSP on ultrasonography, most surface implanted CSPs (8/11, 72.7%) could be successfully treated with systemic MTX, whereas most deeply implanted CSPs (9/10, 90%) had failed systemic MTX but still could be successfully treated with additional UAE combined with local MTX. All patients recovered without severe side effects. Most patients with a future desire for reproduction achieved subsequent pregnancy. Conclusions: For CSP patients suitable for nonsurgical treatment, UAE combined with local MTX would be the superior option compared with systemic MTX in the cases with deep implantation of amniotic sac.« less

Remotely Monitored Sealing Array Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

2012-09-12

The Remotely Monitored Sealing Array (RMSA) utilizes the Secure Sensor Platform (SSP) framework to establish the fundamental operating capabilities for communication, security, power management, and cryptography. In addition to the SSP framework the RMSA software has unique capabilities to support monitoring a fiber optic seal. Fiber monitoring includes open and closed as well as parametric monitoring to detect tampering attacks. The fiber monitoring techniques, using the SSP power management processes, allow the seals to last for years while maintaining the security requirements of the monitoring application. The seal is enclosed in a tamper resistant housing with software to support activemore » tamper monitoring. New features include LED notification of fiber closure, the ability to retrieve the entire fiber optic history via translator command, separate memory storage for fiber optic events, and a more robust method for tracking and resending failed messages.« less

Design and evaluation of a sensor fail-operational control system for a digitally controlled turbofan engine

NASA Technical Reports Server (NTRS)

Hrach, F. J.; Arpasi, D. J.; Bruton, W. M.

1975-01-01

A self-learning, sensor fail-operational, control system for the TF30-P-3 afterburning turbofan engine was designed and evaluated. The sensor fail-operational control system includes a digital computer program designed to operate in conjunction with the standard TF30-P-3 bill-of-materials control. Four engine measurements and two compressor face measurements are tested. If any engine measurements are found to have failed, they are replaced by values synthesized from computer-stored information. The control system was evaluated by using a realtime, nonlinear, hybrid computer engine simulation at sea level static condition, at a typical cruise condition, and at several extreme flight conditions. Results indicate that the addition of such a system can improve the reliability of an engine digital control system.

Study of fail-safe abort system for an actively cooled hypersonic aircraft, volume 2

NASA Technical Reports Server (NTRS)

Peeples, M. E.; Herring, R. L.

1976-01-01

Conceptual designs of a fail-safe abort system for hydrogen fueled actively cooled high speed aircraft are examined. The fail-safe concept depends on basically three factors: (1) a reliable method of detecting a failure or malfunction in the active cooling system, (2) the optimization of abort trajectories which minimize the descent heat load to the aircraft, and (3) fail-safe thermostructural concepts to minimize both the weight and the maximum temperature the structure will reach during descent. These factors are examined and promising approaches are evaluated based on weight, reliability, ease of manufacture and cost.

Bolt Stress Monitor

NASA Technical Reports Server (NTRS)

1978-01-01

In photo, an engineer is using a new Ultrasonic Bolt Stress Monitor developed by NASA's Langley Research Center to determine whether a bolt is properly tightened. A highly accurate device, the monitor is an important tool in construction of such structures as pressure vessels, bridges and power plants, wherein precise measurement of the stress on a tightened bolt is critical. Overtightened or undertightened bolts can fail and cause serious industrial accidents or costly equipment break-downs. There are a number of methods for measuring bolt stress. Most widely used and least costly is the torque wrench, which is inherently inaccurate; it does not take into account the friction between nut and bolt, which has an influence on stress. At the other end of the spectrum, there are accurate stress-measuring systems, but they are expensive and not portable. The battery-powered Langley monitor fills a need; it is inexpensive, lightweight, portable and extremely accurate because it is not subject to friction error. Sound waves are transmitted to the bolt and a return signal is received. As the bolt is tightened, it undergoes changes in resonance due to stress, in the manner that a violin string changes tone when it is tightened. The monitor measures the changes in resonance and provides a reading of real stress on the bolt. The device, patented by NASA, has aroused wide interest and a number of firms have applied for licenses to produce it for the commercial market.

Margins Associated with Loss of Assured Safety for Systems with Multiple Time-Dependent Failure Modes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Helton, Jon C.; Brooks, Dusty Marie; Sallaberry, Cedric Jean-Marie.

Representations for margins associated with loss of assured safety (LOAS) for weak link (WL)/strong link (SL) systems involving multiple time-dependent failure modes are developed. The following topics are described: (i) defining properties for WLs and SLs, (ii) background on cumulative distribution functions (CDFs) for link failure time, link property value at link failure, and time at which LOAS occurs, (iii) CDFs for failure time margins defined by (time at which SL system fails) – (time at which WL system fails), (iv) CDFs for SL system property values at LOAS, (v) CDFs for WL/SL property value margins defined by (property valuemore » at which SL system fails) – (property value at which WL system fails), and (vi) CDFs for SL property value margins defined by (property value of failing SL at time of SL system failure) – (property value of this SL at time of WL system failure). Included in this presentation is a demonstration of a verification strategy based on defining and approximating the indicated margin results with (i) procedures based on formal integral representations and associated quadrature approximations and (ii) procedures based on algorithms for sampling-based approximations.« less

U.S. Patent Pending, Cyberspace Security System for Complex Systems, U.S. Patent Application No.: 14/134,949

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abercrombie, Robert K; Sheldon, Frederick T; Mili, Ali

A computer implemented method monetizes the security of a cyber-system in terms of losses each stakeholder may expect to lose if a security break down occurs. A non-transitory media stores instructions for generating a stake structure that includes costs that each stakeholder of a system would lose if the system failed to meet security requirements and generating a requirement structure that includes probabilities of failing requirements when computer components fails. The system generates a vulnerability model that includes probabilities of a component failing given threats materializing and generates a perpetrator model that includes probabilities of threats materializing. The system generatesmore » a dot product of the stakes structure, the requirement structure, the vulnerability model and the perpetrator model. The system can further be used to compare, contrast and evaluate alternative courses of actions best suited for the stakeholders and their requirements.« less

SeaDataNet network services monitoring: Definition and Implementation of Service availability index

NASA Astrophysics Data System (ADS)

Lykiardopoulos, Angelos; Mpalopoulou, Stavroula; Vavilis, Panagiotis; Pantazi, Maria; Iona, Sissy

2014-05-01

SeaDataNet (SDN) is a standardized system for managing large and diverse data sets collected by the oceanographic fleets and the automatic observation systems. The SeaDataNet network is constituted of national oceanographic data centres of 35 countries, active in data collection. SeaDataNetII project's objective is to upgrade the present SeaDataNet infrastructure into an operationally robust and state-of-the-art infrastructure; therefore Network Monitoring is a step to this direction. The term Network Monitoring describes the use of system that constantly monitors a computer network for slow or failing components and that notifies the network administrator in case of outages. Network monitoring is crucial when implementing widely distributed systems over the Internet and in real-time systems as it detects malfunctions that may occur and notifies the system administrator who can immediately respond and correct the problem. In the framework of SeaDataNet II project a monitoring system was developed in order to monitor the SeaDataNet components. The core system is based on Nagios software. Some plug-ins were developed to support SeaDataNet modules. On the top of Nagios Engine a web portal was developed in order to give access to local administrators of SeaDataNet components, to view detailed logs of their own service(s). Currently the system monitors 35 SeaDataNet Download Managers, 9 SeaDataNet Services, 25 GeoSeas Download Managers and 23 UBSS Download Managers . Taking advantage of the continuous monitoring of SeaDataNet system components a total availability index will be implemented. The term availability can be defined as the ability of a functional unit to be in a state to perform a required function under given conditions at a given instant of time or over a given time interval, assuming that the required external resources are provided. Availability measures can be considered as a are very important benefit becauseT - The availability trends that can be extracted from the stored availability measurements will give an indication of the condition of the service modules. - Will help in planning upgrades planning - and the maintenance of the network service. - It is a prerequisite in case of signing a Service Level Agreement. To construct the service availability index, a method for measuring availability of SeaDataNet network is developed and a database is implemented to store the measured values. Although the measurements of availability of a single component in a network service can be considered as simple (is a percentage of time in a year that the service is available to the users), the ipmlementation of a method to measure the total availability of a composite system can be complicated and there is no a standardized method to deal with it. The method followed to calculate the total availability index in case of SeaDataNet can be described as follows: The whole system was divided in operational modules providing a single service in which the availability can be measured by monitoring portal. Next the dependences between these modules were defined in order to formulate the influence of availability of each module against the whole system. For each module a weight coefficient depending on module's involvement in total system productivity was defined. A mathematical formula was developed to measure the index.

The Standard Autonomous File Server, A Customized, Off-the-Shelf Success Story

NASA Technical Reports Server (NTRS)

Semancik, Susan K.; Conger, Annette M.; Obenschain, Arthur F. (Technical Monitor)

2001-01-01

The Standard Autonomous File Server (SAFS), which includes both off-the-shelf hardware and software, uses an improved automated file transfer process to provide a quicker, more reliable, prioritized file distribution for customers of near real-time data without interfering with the assets involved in the acquisition and processing of the data. It operates as a stand-alone solution, monitoring itself, and providing an automated fail-over process to enhance reliability. This paper describes the unique problems and lessons learned both during the COTS selection and integration into SAFS, and the system's first year of operation in support of NASA's satellite ground network. COTS was the key factor in allowing the two-person development team to deploy systems in less than a year, meeting the required launch schedule. The SAFS system has been so successful; it is becoming a NASA standard resource, leading to its nomination for NASA's Software of the Year Award in 1999.

Flyover-noise measurement and prediction

NASA Technical Reports Server (NTRS)

Peart, Noel A.

1991-01-01

Details are presented for the measurement and prediction of aircraft flyover noise to be used for certification, research and development, community noise surveys, airport monitors, and pass fail criteria. Test details presented are applicable to all types of aircraft, both large and small, and the use of Federal Aviation Regulations (FAR) Part 36 (ref. 1) is emphasized. Accuracy of noise measurements is important. Thus, a pass-fail criterion should be used for all noise measurements. Finally, factors which influence the sound propagation and noise prediction procedures, such as atmospheric and ground effects, are also presented.

Evolution of the Hubble Space Telescope Safing Systems

NASA Technical Reports Server (NTRS)

Pepe, Joyce; Myslinski, Michael

2006-01-01

The Hubble Space Telescope (HST) was launched on April 24 1990, with an expected lifespan of 15 years. Central to the spacecraft design was the concept of a series of on-orbit shuttle servicing missions permitting astronauts to replace failed equipment, update the scientific instruments and keep the HST at the forefront of astronomical discoveries. One key to the success of the Hubble mission has been the robust Safing systems designed to monitor the performance of the observatory and to react to keep the spacecraft safe in the event of equipment anomaly. The spacecraft Safing System consists of a range of software tests in the primary flight computer that evaluate the performance of mission critical hardware, safe modes that are activated when the primary control mode is deemed inadequate for protecting the vehicle, and special actions that the computer can take to autonomously reconfigure critical hardware. The HST Safing System was structured to autonomously detect electrical power system, data management system, and pointing control system malfunctions and to configure the vehicle to ensure safe operation without ground intervention for up to 72 hours. There is also a dedicated safe mode computer that constantly monitors a keep-alive signal from the primary computer. If this signal stops, the safe mode computer shuts down the primary computer and takes over control of the vehicle, putting it into a safe, low-power configuration. The HST Safing system has continued to evolve as equipment has aged, as new hardware has been installed on the vehicle, and as the operation modes have matured during the mission. Along with the continual refinement of the limits used in the safing tests, several new tests have been added to the monitoring system, and new safe modes have been added to the flight software. This paper will focus on the evolution of the HST Safing System and Safing tests, and the importance of this evolution to prolonging the science operations of the telescope.

The aquatic real-time monitoring network; in-situ optical sensors for monitoring the nation's water quality

USGS Publications Warehouse

Pellerin, Brian A.; Bergamaschi, Brian A.; Murdoch, Peter S.; Downing, Bryan D.; Saraceno, John Franco; Aiken, George R.; Striegl, Robert G.

2011-01-01

Floods, hurricanes, and longer-term changes in climate and land use can have profound effects on water quality due to shifts in hydrologic flow paths, water residence time, precipitation patterns, connectivity between rivers and uplands, and many other factors. In order to understand and respond to changes in hydrology and water quality, resource managers and policy makers have a need for accurate and early indicators, as well as the ability to assess possible mechanisms and likely outcomes. In-situ optical sensors-those making continuous measurements of constituents by absorbance or fluorescence properties in the environment at timescales of minutes to years-have a long history in oceanography for developing highly resolved concentrations and fluxes, but are not commonly used in freshwater systems. The United States Geological Survey (USGS) has developed the Aquatic Real-Time Monitoring Network, with high-resolution optical data collection for organic carbon, nutrients, and sediment in large coastal rivers, along with continuous measurements of discharge, water temperature, and dissolved inorganic carbon. The collecting of continuous water-quality data in the Nation?s waterways has revealed temporal trends and spatial patterns in constituents that traditional sampling approaches fail to capture, and will serve a critical role in monitoring, assessment and decision-making in a rapidly changing landscape.

In Brief: Improving Mississippi River water quality

NASA Astrophysics Data System (ADS)

Showstack, Randy

2007-10-01

If water quality in the Mississippi River and the northern Gulf of Mexico is to improve, the U.S. Environmental Protection Agency (EPA) needs to take a stronger leadership role in implementing the federal Clean Water Act, according to a 16 October report from the U.S. National Research Council. The report notes that EPA has failed to use its authority to coordinate and oversee activities along the river. In addition, river states need to be more proactive and cooperative in efforts to monitor and improve water quality, and the river should be monitored and evaluated as a single system, the report indicates. Currently, the 10 states along the river conduct separate and widely varying water quality monitoring programs. ``The limited attention being given to monitoring and managing the Mississippi's water quality does not match the river's significant economic, ecological, and cultural importance,'' said committee chair David A. Dzombak, director of the Steinbrenner Institute for Environmental Education and Research at Carnegie Mellon University, Pittsburgh, Pa. The report notes that while measures taken under the Clean Water Act have successfully reduced much point source pollution, nutrient and sediment loads from nonpoint sources continue to be significant problems. For more information, visit the Web site: http://books.nap.edu/catalog.php?record_id=12051.

Development of nanoparticle embedded sizing for enhanced structural health monitoring of carbon fiber composites

NASA Astrophysics Data System (ADS)

Bowland, Christopher C.; Wang, Yangyang; Naskar, Amit K.

2017-04-01

Carbon fiber composites experience sudden, catastrophic failure when exposed to sufficient stress levels and provide no obvious visual indication of damage before they fail. With the commercial adoption of these high-performance composites in structural applications, a need for in-situ monitoring of their structural integrity is paramount. Therefore, ways in which to monitor these systems has gathered research interest. A common method for accomplishing this is measuring through-thickness resistance changes of the composite due to the fact that carbon fiber composites are electrically conductive. This provides information on whole-body stress levels imparted on the composite and can help identify the presence of damage. However, this technique relies on the carbon fiber and polymer matrix to reveal a resistance change. Here, an approach is developed that increases damage detection sensitivity. This is achieved by developing a facile synthesis method of integrating semiconducting nanomaterials, such as silicon carbide, into carbon fiber sizing. The piezoresistive effect exhibited by these nanomaterials provides more pronounced resistance changes in response to mechanical stress as compared to carbon fiber alone. This is investigated through fabricating a unidirectional composite and subsequently monitoring the electrical resistance during mechanical testing. By establishing this route for integrating nanomaterials into carbon fiber composites, various nanomaterials can see future composite integration to realize novel properties.

NASA-DoD Lead-Free Electronics Project: Vibration Test

NASA Technical Reports Server (NTRS)

Woodrow, Thomas A.

2010-01-01

Vibration testing was conducted by Boeing Research and Technology (Seattle) for the NASA-DoD Lead-Free Electronics Solder Project. This project is a follow-on to the Joint Council on Aging Aircraft/Joint Group on Pollution Prevention (JCAA/JG-PP) Lead-Free Solder Project which was the first group to test the reliability of lead-free solder joints against the requirements of the aerospace/miLItary community. Twenty seven test vehicles were subjected to the vibration test conditions (in two batches). The random vibration Power Spectral Density (PSD) input was increased during the test every 60 minutes in an effort to fail as many components as possible within the time allotted for the test. The solder joints on the components were electrically monitored using event detectors and any solder joint failures were recorded on a Labview-based data collection system. The number of test minutes required to fail a given component attached with SnPb solder was then compared to the number of test minutes required to fail the same component attached with lead-free solder. A complete modal analysis was conducted on one test vehicle using a laser vibrometer system which measured velocities, accelerations, and displacements at one . hundred points. The laser vibrometer data was used to determine the frequencies of the major modes of the test vehicle and the shapes of the modes. In addition, laser vibrometer data collected during the vibration test was used to calculate the strains generated by the first mode (using custom software). After completion of the testing, all of the test vehicles were visually inspected and cross sections were made. Broken component leads and other unwanted failure modes were documented.

A user anonymity preserving three-factor authentication scheme for telecare medicine information systems.

PubMed

Tan, Zuowen

2014-03-01

The telecare medicine information system enables the patients gain health monitoring at home and access medical services over internet or mobile networks. In recent years, the schemes based on cryptography have been proposed to address the security and privacy issues in the telecare medicine information systems. However, many schemes are insecure or they have low efficiency. Recently, Awasthi and Srivastava proposed a three-factor authentication scheme for telecare medicine information systems. In this paper, we show that their scheme is vulnerable to the reflection attacks. Furthermore, it fails to provide three-factor security and the user anonymity. We propose a new three-factor authentication scheme for the telecare medicine information systems. Detailed analysis demonstrates that the proposed scheme provides mutual authentication, server not knowing password and freedom of password, biometric update and three-factor security. Moreover, the new scheme provides the user anonymity. As compared with the previous three-factor authentication schemes, the proposed scheme is more secure and practical.

Preventing the next 'SARS' - European healthcare workers' attitudes towards monitoring their health for the surveillance of newly emerging infections: qualitative study

PubMed Central

2011-01-01

Background Hospitals are often the epicentres of newly circulating infections. Healthcare workers (HCWs) are at high risk of acquiring infectious diseases and may be among the first to contract emerging infections. This study aims to explore European HCWs' perceptions and attitudes towards monitoring their absence and symptom reports for surveillance of newly circulating infections. Methods A qualitative study with thematic analysis was conducted using focus group methodology. Forty-nine hospital-based HCWs from 12 hospitals were recruited to six focus groups; two each in England and Hungary and one each in Germany and Greece. Results HCWs perceived risk factors for occupationally acquired infectious diseases to be 1.) exposure to patients with undiagnosed infections 2.) break-down in infection control procedures 3.) immuno-naïvety and 4.) symptomatic colleagues. They were concerned that a lack of monitoring and guidelines for infectious HCWs posed a risk to staff and patients and felt employers failed to take a positive interest in their health. Staffing demands and loss of income were noted as pressures to attend work when unwell. In the UK, Hungary and Greece participants felt monitoring staff absence and the routine disclosure of symptoms could be appropriate provided the effectiveness and efficiency of such a system were demonstrable. In Germany, legislation, privacy and confidentiality were identified as barriers. All HCWs highlighted the need for knowledge and structural improvements for timelier recognition of emerging infections. These included increased suspicion and awareness among staff and standardised, homogenous absence reporting systems. Conclusions Monitoring absence and infectious disease symptom reports among HCWs may be a feasible means of surveillance for emerging infections in some settings. A pre-requisite will be tackling the drivers for symptomatic HCWs to attend work. PMID:21740552

Randomized Trial of Infusion Set Function: Steel Versus Teflon

PubMed Central

Patel, Parul J.; Benasi, Kari; Ferrari, Gina; Evans, Mark G.; Shanmugham, Satya; Wilson, Darrell M.

2014-01-01

Abstract Background: This study compared infusion set function for up to 1 week using either a Teflon® (Dupont™, Wilmington, DE) catheter or a steel catheter for insulin pump therapy in type 1 diabetes mellitus. Subjects and Methods: Twenty subjects participating in a randomized, open-labeled, crossover study were asked to wear two Quick-Set® and two Sure-T® infusion sets (both from Medtronic Minimed, Northridge, CA) until the infusion set failed or was worn for 1 week. All subjects wore a MiniMed continuous glucose monitoring system for the duration of the study. Results: One subject withdrew from the study. There were 38 weeks of Sure-T wear and 39 weeks of Quick-Set wear with no difference in the survival curves of the infusion sets. There was, however, a 15% initial failure rate with the Teflon infusion set. After 7 days, both types of infusion sets had a 64% failure rate. Overall, 30% failed because of hyperglycemia and a failed correction dose, 13% were removed for pain, 10% were pulled out by accident, 10% had erythema and/or induration of>10 mm, 5% fell out because of loss of adhesion, and 4% were removed for infection. The main predictor of length of wear was the individual subject. There was no increase in hyperglycemia or daily insulin requirements when an infusion set was successfully used for 7 days (n=25 of 77 weeks). Conclusions: We found no difference between steel and Teflon infusion sets in their function over 7 days, although 15% of Teflon sets failed because of kinking on insertion. The strongest predictor of prolonged 7-day infusion set function was the individual subject, not the type of infusion set. PMID:24090124

Clinical peptidomic analysis by a one-step direct transfer technology: its potential utility for monitoring of pathophysiological status in female reproductive system disorders.

PubMed

Araki, Yoshihiko; Nonaka, Daisuke; Hamamura, Kensuke; Yanagida, Mitsuaki; Ishikawa, Hitoshi; Banzai, Michio; Maruyama, Mayuko; Endo, Shuichiro; Tajima, Atsushi; Lee, Lyang-Ja; Nojima, Michio; Takamori, Kenji; Yoshida, Koyo; Takeda, Satoru; Tanaka, Kenji

2013-10-01

To date, numerous studies have searched for candidate molecules or clinical examination methods as potential biomarkers for monitoring intractable diseases, such as carcinomas. Evidence accumulated over the past decade shows that many proteolytic peptides appear in human humoral fluids, including peripheral blood, in association with an individual's health condition. Although an analysis of the whole peptide (the 'peptidome') using mass spectrometry is thought to be one of the most powerful and promising experimental approaches, it has failed to identify biomarkers in the clinical blood samples, presumably due to the methodological limitations. In general, commonly used techniques for proteomic analysis of blood require the removal of large amounts of serum/plasma proteins prior to mass spectrometry analysis, and this step seems to have resulted in the overlooking of important biomarkers during the analytical process. Here, we provide a brief overview of a new quantitative peptidomic analysis by a one-step direct transfer technology without depletion of major blood proteins. Using this technology, we herein report experimental data on serum peptidomic analysis for patients with pregnancy-induced hypertension as a clinical model. In addition, we refer to the potential utility of this approach for the monitoring of pathophysiological status in female reproductive system disorders in general. © 2013 The Authors. Journal of Obstetrics and Gynaecology Research © 2013 Japan Society of Obstetrics and Gynecology.

Can arousing feedback rectify lapses in driving? Prediction from EEG power spectra.

PubMed

Lin, Chin-Teng; Huang, Kuan-Chih; Chuang, Chun-Hsiang; Ko, Li-Wei; Jung, Tzyy-Ping

2013-10-01

This study explores the neurophysiological changes, measured using an electroencephalogram (EEG), in response to an arousing warning signal delivered to drowsy drivers, and predicts the efficacy of the feedback based on changes in the EEG. Eleven healthy subjects participated in sustained-attention driving experiments. The driving task required participants to maintain their cruising position and compensate for randomly induced lane deviations using the steering wheel, while their EEG and driving performance were continuously monitored. The arousing warning signal was delivered to participants who experienced momentary behavioral lapses, failing to respond rapidly to lane-departure events (specifically the reaction time exceeded three times the alert reaction time). The results of our previous studies revealed that arousing feedback immediately reversed deteriorating driving performance, which was accompanied by concurrent EEG theta- and alpha-power suppression in the bilateral occipital areas. This study further proposes a feedback efficacy assessment system to accurately estimate the efficacy of arousing warning signals delivered to drowsy participants by monitoring the changes in their EEG power spectra immediately thereafter. The classification accuracy was up 77.8% for determining the need for triggering additional warning signals. The findings of this study, in conjunction with previous studies on EEG correlates of behavioral lapses, might lead to a practical closed-loop system to predict, monitor and rectify behavioral lapses of human operators in attention-critical settings.

Risk Costs for New Dams: Economic Analysis and Effects of Monitoring

NASA Astrophysics Data System (ADS)

Paté-Cornell, M. Elisabeth; Tagaras, George

1986-01-01

This paper presents new developments and illustrations of the introduction of risk and costs in cost-benefit analysis for new dams. The emphasis is on a method of evaluation of the risk costs based on the structure of the local economy. Costs to agricultural property as well as residential, commercial, industrial, and public property are studied in detail. Of particular interest is the case of sequential dam failure and the evaluation of the risk costs attributable to a new dam upstream from an existing one. Three real cases are presented as illustrations of the method: the Auburn Dam, the Dickey-Lincoln School Project, and the Teton Dam, which failed in 1976. This last case provides a calibration tool for the estimation of loss ratios. For these three projects, the risk-modified benefit-cost ratios are computed to assess the effect of the risk on the economic performance of the project. The role of a warning system provided by systematic monitoring of the dam is analyzed: by reducing the risk costs, the warning system attenuates their effect on the benefit-cost ratio. The precursors, however, can be missed or misinterpreted: monitoring does not guarantee that the risks to human life can be reduced to zero. This study shows, in particular, that it is critical to consider the risk costs in the decision to build a new dam when the flood area is large and densely populated.

Effects of Internal Rhetoric on Management Response to External Issues: How Corporate Culture Failed the Asbestos Industry.

ERIC Educational Resources Information Center

Heath, Robert L.

1990-01-01

Demonstrates how corporate culture stifled adaptive efforts of strategic planners, operations managers, industrial hygienists, and issue monitors in the asbestos industry thereby leading it to the brink of bankruptcy. (MG)

Fail-safe system for activity cooled supersonic and hypersonic aircraft. [using liquid hydrogen fuel

NASA Technical Reports Server (NTRS)

Jones, R. A.; Braswell, D. O.; Richie, C. B.

1975-01-01

A fail-safe-system concept was studied as an alternative to a redundant active cooling system for supersonic and hypersonic aircraft which use the heat sink of liquid-hydrogen fuel for cooling the aircraft structure. This concept consists of an abort maneuver by the aircraft and a passive thermal protection system (TPS) for the aircraft skin. The abort manuever provides a low-heat-load descent from normal cruise speed to a lower speed at which cooling is unnecessary, and the passive TPS allows the aircraft skin to absorb the abort heat load without exceeding critical skin temperature. On the basis of results obtained, it appears that this fail-safe-system concept warrants further consideration, inasmuch as a fail-safe system could possibly replace a redundant active cooling system with no increase in weight and would offer other potential advantages.

Study of a fail-safe abort system for an actively cooled hypersonic aircraft. Volume 1: Technical summary

NASA Technical Reports Server (NTRS)

Pirello, C. J.; Herring, R. L.

1976-01-01

Conceptual designs of a fail-safe abort system for hydrogen fueled actively cooled high speed aircraft are examined. The fail-safe concept depends on basically three factors: (1) a reliable method of detecting a failure or malfunction in the active cooling system, (2) the optimization of abort trajectories which minimize the descent heat load to the aircraft, and (3) fail-safe thermostructural concepts to minimize both the weight and the maximum temperature the structure will reach during descent. These factors are examined and promising approaches are evaluated based on weight, reliability, ease of manufacture and cost.

Serum level of uric acid, partly secreted from the failing heart, is a prognostic marker in patients with congestive heart failure.

PubMed

Sakai, Hiroshi; Tsutamoto, Takayoshi; Tsutsui, Takashi; Tanaka, Toshinari; Ishikawa, Chitose; Horie, Minoru

2006-08-01

A recent study suggested that xanthine oxidase is activated in congestive heart failure (CHF). However, whether uric acid (UA) is secreted from the failing heart remains unknown, so it is currently unclear whether serum UA can provide prognostic information independent of brain natriuretic peptide (BNP). Serum UA was measured in the aortic root (AO) and the coronary sinus (CS) of 74 patients with CHF. The serum UA level was significantly higher in the CS than in the AO. The transcardiac gradient of UA (CS-AO) increased with the severity of CHF, inversely correlated with left ventricular ejection fraction (LVEF) and positively correlated with left ventricular end-diastolic volume index. The plasma levels of norepinephrine, BNP, UA, and LVEF were monitored prospectively in 150 CHF patients for a mean follow-up of 3 years. High plasma levels of UA (p<0.001) and BNP (p<0.001) were shown by multivariate stepwise analysis to be independent predictors of mortality. High plasma UA level, partly secreted from the failing heart, is a prognostic predictor independent of BNP in patients with CHF. Monitoring a combination of BNP and UA may be useful for the management of patients with CHF.

Bias in groundwater samples caused by wellbore flow

USGS Publications Warehouse

Reilly, Thomas E.; Franke, O. Lehn; Bennett, Gordon D.

1989-01-01

Proper design of physical installations and sampling procedures for groundwater monitoring networks is critical for the detection and analysis of possible contaminants. Monitoring networks associated with known contaminant sources sometimes include an array of monitoring wells with long well screens. The purpose of this paper is: (a) to report the results of a numerical experiment indicating that significant borehole flow can occur within long well screens installed in homogeneous aquifers with very small head differences in the aquifer (less than 0.01 feet between the top and bottom of the screen); (b) to demonstrate that contaminant monitoring wells with long screens may completely fail to fulfill their purpose in many groundwater environments.

Assessing the feasibility of using uniaxial accelerometers with an online support platform in the delivery of a community-based exercise referral scheme.

PubMed

Hawkins, Jemma L; Oliver, Emily J; Wyatt-Williams, Jeannie; Scale, Elaine; van Woerden, Hugo C

2014-10-01

Exercise referral schemes are established within community-based health care; however, they have been criticized for failing to evidence long-term behavior change relative to usual care. As such, recent reviews have called for refinement of their delivery with a focus on embedded strategies targeting client motivation. This research letter presents findings from an initial pilot trial conducted within Wales' National Exercise Referral Scheme (NERS), examining the feasibility of using validated physical activity monitoring devices and an accompanying online platform within standard scheme delivery. 30 individuals referred to generic or cardiovascular pathways were offered the system; of these 17 agreed to participate. Common reasons for declining were clustered into lack of technology literacy or access, condition severity, or fear of costs associated with losing the device. Analysis of follow-up interviews after 4 weeks of use indicated that while participants found the monitoring devices practical and informative, only a minority (n = 4) were using the system in full. Crucially, the system element most aligned with contemporary theories of motivation (the online portal) was not used as expected. In addition, feedback from exercise referral professionals indicated that there were demands for support from clients, which might be mitigated by more effective independent system use. Recommendations for larger scale trials using similar systems include consideration of targeted patient groups, equity of access, and providing adequate technological support that is currently beyond the capacity of the NERS system. © The Author(s) 2014.

xDSL connection monitor

DOEpatents

Horton, John J.

2006-04-11

A system and method of maintaining communication between a computer and a server, the server being in communication with the computer via xDSL service or dial-up modem service, with xDSL service being the default mode of communication, the method including sending a request to the server via xDSL service to which the server should respond and determining if a response has been received. If no response has been received, displaying on the computer a message (i) indicating that xDSL service has failed and (ii) offering to establish communication between the computer and the server via the dial-up modem, and thereafter changing the default mode of communication between the computer and the server to dial-up modem service. In a preferred embodiment, an xDSL service provider monitors dial-up modem communications and determines if the computer dialing in normally establishes communication with the server via xDSL service. The xDSL service provider can thus quickly and easily detect xDSL failures.

Accounting for unintended binding events in the analysis of quartz crystal microbalance kinetic data.

PubMed

Heller, Gabriella T; Zwang, Theodore J; Sarapata, Elizabeth A; Haber, Michael A; Sazinsky, Matthew H; Radunskaya, Ami E; Johal, Malkiat S

2014-05-01

Previous methods for analyzing protein-ligand binding events using the quartz crystal microbalance with dissipation monitoring (QCM-D) fail to account for unintended binding that inevitably occurs during surface measurements and obscure kinetic information. In this article, we present a system of differential equations that accounts for both reversible and irreversible unintended interactions. This model is tested on three protein-ligand systems, each of which has different features, to establish the feasibility of using the QCM-D for protein binding analysis. Based on this analysis, we were able to obtain kinetic information for the intended interaction that is consistent with those obtained in literature via bulk-phase methods. In the appendix, we include a method for decoupling these from the intended binding events and extracting relevant affinity information. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of ABCD transformations on beam paraxiality.

PubMed

Vaveliuk, Pablo; Martinez-Matos, Oscar

2011-12-19

The limits of the paraxial approximation for a laser beam under ABCD transformations is established through the relationship between a parameter concerning the beam paraxiality, the paraxial estimator, and the beam second-order moments. The applicability of such an estimator is extended to an optical system composed by optical elements as mirrors and lenses and sections of free space, what completes the analysis early performed for free-space propagation solely. As an example, the paraxiality of a system composed by free space and a spherical thin lens under the propagation of Hermite-Gauss and Laguerre-Gauss modes is established. The results show that the the paraxial approximation fails for a certain feasible range of values of main parameters. In this sense, the paraxial estimator is an useful tool to monitor the limits of the paraxial optics theory under ABCD transformations.

Development of single-cell protectors for sealed silver-zinc cells

NASA Technical Reports Server (NTRS)

Lear, J. W.; Donovan, R. L.; Imamura, M. S.

1978-01-01

Three design approaches to cell-level protection were developed, fabricated, and tested. These systems are referred to as the single-cell protector (SCP), multiplexed-cell protector(MCP). To evaluate the systems 18-cell battery packs without cell level control were subjected to cycle life test. A total of five batteries were subjected to simulate synchronous orbit cycling at 40% depth of discharge at 22C. Batteries without cell-level protection failed between 345 and 255 cycles. Cell failure in the cell level protected batteries occurred between 412 and 540. It was determined that the cell-level monitoring and protection is necessary to attain the long cycle life of a AgZn battery. The best method of providing control and protection of the AgZn cells depends on the specific application and capability of the user.

Vibration Based Crack Detection in a Rotating Disk. Part 2; Experimental Results

NASA Technical Reports Server (NTRS)

Gyekenyesi, Andrew L.; Sawicki, Jerzy T.; Martin, Richard E.; Haase, Wayne C.; Baaklini, George

2005-01-01

This paper describes the experimental results concerning the detection of a crack in a rotating disk. The goal was to utilize blade tip clearance and shaft vibration measurements to monitor changes in the system's center of mass and/or blade deformation behaviors. The concept of the approach is based on the fact that the development of a disk crack results in a distorted strain field within the component. As a result, a minute deformation in the disk's geometry as well as a change in the system's center of mass occurs. Here, a notch was used to simulate an actual crack. The vibration based experimental results failed to identify the existence of a notch when utilizing the approach described above, even with a rather large, circumferential notch (l.2 in.) located approximately mid-span on the disk (disk radius = 4.63 in. with notch at r = 2.12 in.). This was somewhat expected, since the finite element based results in Part 1 of this study predicted changes in blade tip clearance as well as center of mass shifts due to a notch to be less than 0.001 in. Therefore, the small changes incurred by the notch could not be differentiated from the mechanical and electrical noise of the rotor system. Although the crack detection technique of interest failed to identify the existence ofthe notch, the vibration data produced and captured here will be utilized in upcoming studies that will focus on different data mining techniques concerning damage detection in a disk.

Evolution of grid-wide access to database resident information in ATLAS using Frontier

NASA Astrophysics Data System (ADS)

Barberis, D.; Bujor, F.; de Stefano, J.; Dewhurst, A. L.; Dykstra, D.; Front, D.; Gallas, E.; Gamboa, C. F.; Luehring, F.; Walker, R.

2012-12-01

The ATLAS experiment deployed Frontier technology worldwide during the initial year of LHC collision data taking to enable user analysis jobs running on the Worldwide LHC Computing Grid to access database resident data. Since that time, the deployment model has evolved to optimize resources, improve performance, and streamline maintenance of Frontier and related infrastructure. In this presentation we focus on the specific changes in the deployment and improvements undertaken, such as the optimization of cache and launchpad location, the use of RPMs for more uniform deployment of underlying Frontier related components, improvements in monitoring, optimization of fail-over, and an increasing use of a centrally managed database containing site specific information (for configuration of services and monitoring). In addition, analysis of Frontier logs has allowed us a deeper understanding of problematic queries and understanding of use cases. Use of the system has grown beyond user analysis and subsystem specific tasks such as calibration and alignment, extending into production processing areas, such as initial reconstruction and trigger reprocessing. With a more robust and tuned system, we are better equipped to satisfy the still growing number of diverse clients and the demands of increasingly sophisticated processing and analysis.

Engaging stakeholders for adaptive management using structured decision analysis

USGS Publications Warehouse

Irwin, Elise R.; Kathryn, D.; Kennedy, Mickett

2009-01-01

Adaptive management is different from other types of management in that it includes all stakeholders (versus only policy makers) in the process, uses resource optimization techniques to evaluate competing objectives, and recognizes and attempts to reduce uncertainty inherent in natural resource systems. Management actions are negotiated by stakeholders, monitored results are compared to predictions of how the system should respond, and management strategies are adjusted in a “monitor-compare-adjust” iterative routine. Many adaptive management projects fail because of the lack of stakeholder identification, engagement, and continued involvement. Primary reasons for this vary but are usually related to either stakeholders not having ownership (or representation) in decision processes or disenfranchisement of stakeholders after adaptive management begins. We present an example in which stakeholders participated fully in adaptive management of a southeastern regulated river. Structured decision analysis was used to define management objectives and stakeholder values and to determine initial flow prescriptions. The process was transparent, and the visual nature of the modeling software allowed stakeholders to see how their interests and values were represented in the decision process. The development of a stakeholder governance structure and communication mechanism has been critical to the success of the project.

[Methodical problems of monitoring of fine particulate matters in atmospheric air of residential areas].

PubMed

Karelin, A O; Lomtev, A Yu; Mozzhukhina, N A; Yeremin, G B; Nikonov, V A

Inhalation of fine particulate matters (PM and PM ) poses a threat for the health of population. Purpose of the study the analysis of the monitoring of fine particulate matters in the atmospheric air of Saint-Petersburg and identification of the main problems of the monitoring. Research methods methods of scientific hypothetical deductive cognition, sanitary-statistical methods, general logical methods and approaches of researches: analysis, synthesis, abstracting, generalization, induction. Results. The article represents the analysis of the monitoring of fine particulate matters in the atmospheric air of Saint- Petersburg. Only 11 in automatic monitoring stations out of 22 there is carried out the control of fine particulate matters: in 7 - PM and PM, and in 4 - PM The average year concentrations were below MAC in all the stations. The maximum concentrations achieved 3 MAC, but the repeatance of cases of exceedence of concentrations more than MAC was very rare. On the average of the city concentrations of PM were decreased from 0,8 MAC in 2006 and 1,1 MAC in 2007 to 0,5 MAC in 2013-14. The executed analysis revealed main problems of the monitoring of fine particulate matters in the Russian Federation. They include the absence of the usage 1of the officially approved methods of controlling of PM and PM in the atmospheric air until March 1, 2016, lack of the modern equipment for measurement of fine particulate matters. Conclusions. Therefore, the state of the monitoring of fine particulate matters in the atmospheric air in the Russian Federation fails to be satisfactory. It is necessary to improve system of the monitoring, create modern Russian appliances, methods and means for measurement of fine particulate matters concentrations in the atmospheric air.

Monitoring the Quality of Medicines: Results from Africa, Asia, and South America

PubMed Central

Hajjou, Mustapha; Krech, Laura; Lane-Barlow, Christi; Roth, Lukas; Pribluda, Victor S.; Phanouvong, Souly; El-Hadri, Latifa; Evans, Lawrence; Raymond, Christopher; Yuan, Elaine; Siv, Lang; Vuong, Tuan-Anh; Boateng, Kwasi Poku; Okafor, Regina; Chibwe, Kennedy M.; Lukulay, Patrick H.

2015-01-01

Monitoring the quality of medicines plays a crucial role in an integrated medicines quality assurance system. In a publicly available medicines quality database (MQDB), the U.S. Pharmacopeial Convention (USP) reports results of data collected from medicines quality monitoring (MQM) activities spanning the period of 2003–2013 in 17 countries of Africa, Asia, and South America. The MQDB contains information on 15,063 samples collected and tested using Minilab® screening methods and/or pharmacopeial methods. Approximately 71% of the samples reported came from Asia, 23% from Africa, and 6% from South America. The samples collected and tested include mainly antibiotic, antimalarial, and antituberculosis medicines. A total of 848 samples, representing 5.6% of total samples, failed the quality test. The failure proportion per region was 11.5%, 10.4%, and 2.9% for South America, Africa, and Asia, respectively. Eighty-one counterfeit medicines were reported, 86.4% of which were found in Asia and 13.6% in Africa. Additional analysis of the data shows the distribution of poor-quality medicines per region and by therapeutic indication as well as possible trends of counterfeit medicines. PMID:25897073

Initial in vitro and in vivo evaluation of a self-monitoring prosthetic bypass graft.

PubMed

Neville, Richard F; Gupta, Samit K; Kuraguntla, David J

2017-06-01

Prosthetic grafts used for lower extremity revascularization and dialysis access fail because of hyperplastic stenosis and thrombosis. Graft surveillance is advocated to monitor function; however, graft failure can occur between episodic examinations. An innovative sensor with wireless, microchip technology allows automated surveillance with assessment of graft function using a "cloud"-based algorithm. We performed proof-of-concept experiments with in vitro and in vivo models to assess the feasibility such a real-time graft surveillance system. A self-monitoring graft system was evaluated consisting of a prosthetic conduit of expanded polytetrafluoroethylene and a sensor unit, and a microsensor, microelectronics, battery, and remote processor with a monitor. The sensor unit was integrated on the extraluminal surface of expanded polytetrafluoroethylene grafts without compromise to the lumen of the conduit. The grafts were tested in vitro in a pulsatile, recirculating flow system under physiologic flow parameters. The hemodynamic parameters were varied to assess the ability to obtain wireless signal acquisition reflecting real-time flow properties in vitro. Segments of custom tubing with reduced diameters were inserted into the model to mimic stenosis proximal and distal to the grafts. After characterization of the initial data, the self-monitoring grafts were implanted in an ovine carotid model to assess proof of concept in vivo with 30-day follow-up of signal acquisition as well as arteriographic and histologic analysis. In vitro flow data demonstrated the device was able to determine factors related to prosthetic graft function under varied hemodynamic flow conditions. Wireless signal acquisition using Bluetooth technology (Bluetooth SIG, Inc, Kirkland, Wash) allowed remote data analysis reflecting graft flow parameters through changes in microsensor voltage and frequency. Waveform analysis was applied to construct an algorithm using proprietary software and determine a parameter for graft flow characteristics. This algorithm allowed determination of the degree of stenosis and location of stenosis location (proximal or distal) for display on a remote monitor in real time. Subsequent in vivo experiments confirmed the ability of the system to generate signal acquisition through skin and soft tissue under biologic conditions with no arteriographic stenosis and a favorable healing response at 30-day harvest. Initial in vitro and in vivo experiments demonstrate the ability for a self-monitoring graft system to remotely monitor hemodynamic parameters reflecting graft function using wireless data transmission. This automated system shows promise to deliver real-time data that can be analyzed by cloud-based algorithms alerting the clinician of a change in graft function or development of stenosis for further diagnostic study or intervention before graft failure. Copyright © 2016 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.

New Algorithms Manage Fourfold Redundancy

NASA Technical Reports Server (NTRS)

Gelderloos, H. C.

1982-01-01

Redundant sensors, actuators, and computers improve reliability of complex control systems, such as those in nuclear powerplants and aircraft. If one or more redundant elements fail, another takes over so that normal operation is not interrupted. Quad selection filter rejects data from null-failed and hardover-failed and hardover-failed units.

Applications of Quantum Probability Theory to Dynamic Decision Making

DTIC Science & Technology

2015-08-13

Final Report 08/13/2015 DISTRIBUTION A : Distribution approved for public release. AF Office Of Scientific Research (AFOSR)/ RTC Arlington, Virginia 22203...for failing to comply with a collection of information   if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM...SPONSOR/MONITOR’S ACRONYM(S) AFRL/AFOSR RTC 11. SPONSOR/MONITOR’S REPORT NUMBER(S) 12. DISTRIBUTION/AVAILABILITY STATEMENT A DISTRIBUTION UNLIMITED: PB

Radiologic Monitoring of Faculty and Staff in an Electrophysiology Lab Using a Real-Time Dose Monitoring System

NASA Astrophysics Data System (ADS)

Chardenet, Kathleen A.

Purpose: A real-time dose management system was used to determine if radiation exposure levels would decrease when providers were privy to their real-time radiation exposure levels. Six aggregate categories of providers were first blinded (phase 1) and subsequently made aware of their radiation exposure levels during electrophysiology procedures (phase 2). Methods: A primary, quantitative crossover study of faculty and staff working in an electrophysiology lab at the University of Michigan Hospitals setting occurred. Participants in the control group was first blinded in phase 1 to their radiation exposure over an 10-week time period. The same group subsequently became the treatment group in phase 2 when over a second 10-week period real-time exposure levels were made available to them. Power analysis, using a 40% decrease in exposure, was calculated using a variance of radiation exposure equal to the mean radiation exposure with 80% power and alpha = .05. Calculations revealed 102 subjects in each treatment and control group were necessary. Results: Using the mixed effect linear model, a significant decrease in radiation levels occurred in phase 2 as compared to phase 1 for the operator role represented by the combined electrophysiologist-fellow role with a P value of .025. Exposure levels in all other provider groups for phase 1 or 2 failed to reach statistical significance. All dose values were low and well below the US maximum allowable yearly dose of 5,000 mrem per year. Conclusion: A real-time radiation dose monitoring system during electrophysiology procedures may significantly lower occupational radiation exposure in health care workers.

The environmental audit. I. Concepts

NASA Astrophysics Data System (ADS)

Schaeffer, David J.; Kerster, Harold W.; Perry, James A.; Cox, David K.

1985-05-01

Extensive criticism of water quality monitoring programs has developed as costs are compared with the benefits produced by monitoring efforts. Collecting water quality data while developing understanding of the functional character of the environment will improve water quality monitoring data utility in environmental management. The “environmental audit” characterizes the attributes of the natural environment (that is, attribute type, intensity, and variability), providing a theoretical as well as practical foundation for data interpretation. In the view proposed here, traditional monitoring means the very narrow activity of collecting samples and perhaps analyzing them and storing the analyses. In the environmental audit, these activities are a mechanism to systematically improve environmental monitoring and assessment by improving the design and implementation of environmental programs. Major reasons why existing programs fail to meet the needs of legislators, regulators, and conservationists are identified.

A prospective randomized trial examining health care utilization in individuals using multiple smartphone-enabled biosensors.

PubMed

Bloss, Cinnamon S; Wineinger, Nathan E; Peters, Melissa; Boeldt, Debra L; Ariniello, Lauren; Kim, Ju Young; Sheard, Judith; Komatireddy, Ravi; Barrett, Paddy; Topol, Eric J

2016-01-01

Background. Mobile health and digital medicine technologies are becoming increasingly used by individuals with common, chronic diseases to monitor their health. Numerous devices, sensors, and apps are available to patients and consumers-some of which have been shown to lead to improved health management and health outcomes. However, no randomized controlled trials have been conducted which examine health care costs, and most have failed to provide study participants with a truly comprehensive monitoring system. Methods. We conducted a prospective randomized controlled trial of adults who had submitted a 2012 health insurance claim associated with hypertension, diabetes, and/or cardiac arrhythmia. The intervention involved receipt of one or more mobile devices that corresponded to their condition(s) (hypertension: Withings Blood Pressure Monitor; diabetes: Sanofi iBGStar Blood Glucose Meter; arrhythmia: AliveCor Mobile ECG) and an iPhone with linked tracking applications for a period of 6 months; the control group received a standard disease management program. Moreover, intervention study participants received access to an online health management system which provided participants detailed device tracking information over the course of the study. This was a monitoring system designed by leveraging collaborations with device manufacturers, a connected health leader, health care provider, and employee wellness program-making it both unique and inclusive. We hypothesized that health resource utilization with respect to health insurance claims may be influenced by the monitoring intervention. We also examined health-self management. Results & Conclusions. There was little evidence of differences in health care costs or utilization as a result of the intervention. Furthermore, we found evidence that the control and intervention groups were equivalent with respect to most health care utilization outcomes. This result suggests there are not large short-term increases or decreases in health care costs or utilization associated with monitoring chronic health conditions using mobile health or digital medicine technologies. Among secondary outcomes there was some evidence of improvement in health self-management which was characterized by a decrease in the propensity to view health status as due to chance factors in the intervention group.

A prospective randomized trial examining health care utilization in individuals using multiple smartphone-enabled biosensors

PubMed Central

Peters, Melissa; Boeldt, Debra L.; Ariniello, Lauren; Kim, Ju Young; Sheard, Judith; Komatireddy, Ravi; Barrett, Paddy

2016-01-01

Background. Mobile health and digital medicine technologies are becoming increasingly used by individuals with common, chronic diseases to monitor their health. Numerous devices, sensors, and apps are available to patients and consumers–some of which have been shown to lead to improved health management and health outcomes. However, no randomized controlled trials have been conducted which examine health care costs, and most have failed to provide study participants with a truly comprehensive monitoring system. Methods. We conducted a prospective randomized controlled trial of adults who had submitted a 2012 health insurance claim associated with hypertension, diabetes, and/or cardiac arrhythmia. The intervention involved receipt of one or more mobile devices that corresponded to their condition(s) (hypertension: Withings Blood Pressure Monitor; diabetes: Sanofi iBGStar Blood Glucose Meter; arrhythmia: AliveCor Mobile ECG) and an iPhone with linked tracking applications for a period of 6 months; the control group received a standard disease management program. Moreover, intervention study participants received access to an online health management system which provided participants detailed device tracking information over the course of the study. This was a monitoring system designed by leveraging collaborations with device manufacturers, a connected health leader, health care provider, and employee wellness program–making it both unique and inclusive. We hypothesized that health resource utilization with respect to health insurance claims may be influenced by the monitoring intervention. We also examined health-self management. Results & Conclusions. There was little evidence of differences in health care costs or utilization as a result of the intervention. Furthermore, we found evidence that the control and intervention groups were equivalent with respect to most health care utilization outcomes. This result suggests there are not large short-term increases or decreases in health care costs or utilization associated with monitoring chronic health conditions using mobile health or digital medicine technologies. Among secondary outcomes there was some evidence of improvement in health self-management which was characterized by a decrease in the propensity to view health status as due to chance factors in the intervention group. PMID:26788432

CAREER DEVELOPMENT

EPA Science Inventory

The Baltimore Summit Project on Career Development/PERFORMS Enhancement/360 Evaluations for All has made some progress. We have identified the fact that we cannot change the current Pass/Fail PERFORMS system to a tiered system. The current pass/fail system does not have a mechani...

[Factors associated with reported vaccination coverage in early infancy: results of a telephone survey].

PubMed

Nebot, M; Muñoz, E; Figueres, M; Rovira, G; Robert, M; Minguell, D

2001-01-01

Barcelona's Continuing Immunization Plan affords the possibility Of monitoring the immunization coverage of the population by means of the voluntary family postal notification system. Prior studies have revealed that some families fail to provide notification while being correctly vaccinated, which can lead to actual coverage being underestimated. The objectives of this study are to estimate the early childhood immunization coverage of the population and to ascertain the factors associated with failure to provide notification of immunization. A phone survey was conducted on a sample of 500 children regarding whom there was no record of any notification of the first three childhood vaccine doses (diphtheria, tetanus, whooping cough and oral polio), in addition to a sample of 500 children who were on record as having been immunized. To estimate the actual immunization coverage, all children were considered to have been properly immunized when their family members did provide notification. As regards those who failed to reply, it was considered in the worst of cases that these were cases of children who had not be immunized. In the best of cases scenario, a coverage similar to those of the responses was assumed. The response to the questionnaire was higher among those who had previously provided notification of immunization by way of the postal notification system (79.1%) than among those who had failed to provide notification of immunization (67%). The leading factors associated with failure to report immunization status were the size of the families, the use of private health care services and the place of birth of the parents. Solely six (6) cases of those who had failed to report immunization admitted to not having immunized their children, totaling 1.9% of the responses. The immunization coverage of the population in question would total 99.7% in the best of cases and 93.7% in the worst of cases scenario. Immunization coverage of the population in question is quite high. The results underline the importance of promoting immunization notification among health care professionals, especially in the private sector.

NO/redox disequilibrium in the failing heart and cardiovascular system

PubMed Central

Hare, Joshua M.; Stamler, Jonathan S.

2005-01-01

There is growing evidence that the altered production and/or spatiotemporal distribution of reactive oxygen and nitrogen species creates oxidative and/or nitrosative stresses in the failing heart and vascular tree, which contribute to the abnormal cardiac and vascular phenotypes that characterize the failing cardiovascular system. These derangements at the integrated system level can be interpreted at the cellular and molecular levels in terms of adverse effects on signaling elements in the heart, vasculature, and blood that subserve cardiac and vascular homeostasis. PMID:15765132

48 CFR 342.7002 - Procedures to be followed when a contractor fails to perform.

Code of Federal Regulations, 2013 CFR

2013-10-01

... when a contractor fails to perform. 342.7002 Section 342.7002 Federal Acquisition Regulations System... Procedures to be followed when a contractor fails to perform. (a) The Contracting Officer shall initiate immediate action to protect the Government's rights whenever the contractor fails to comply with either the...

48 CFR 342.7002 - Procedures to be followed when a contractor fails to perform.

Code of Federal Regulations, 2012 CFR

2012-10-01

... when a contractor fails to perform. 342.7002 Section 342.7002 Federal Acquisition Regulations System... Procedures to be followed when a contractor fails to perform. (a) The Contracting Officer shall initiate immediate action to protect the Government's rights whenever the contractor fails to comply with either the...

48 CFR 342.7002 - Procedures to be followed when a contractor fails to perform.

Code of Federal Regulations, 2011 CFR

2011-10-01

... when a contractor fails to perform. 342.7002 Section 342.7002 Federal Acquisition Regulations System... Procedures to be followed when a contractor fails to perform. (a) The Contracting Officer shall initiate immediate action to protect the Government's rights whenever the contractor fails to comply with either the...

48 CFR 342.7002 - Procedures to be followed when a contractor fails to perform.

Code of Federal Regulations, 2014 CFR

2014-10-01

... when a contractor fails to perform. 342.7002 Section 342.7002 Federal Acquisition Regulations System... Procedures to be followed when a contractor fails to perform. (a) The Contracting Officer shall initiate immediate action to protect the Government's rights whenever the contractor fails to comply with either the...

48 CFR 342.7002 - Procedures to be followed when a contractor fails to perform.

Code of Federal Regulations, 2010 CFR

2010-10-01

... when a contractor fails to perform. 342.7002 Section 342.7002 Federal Acquisition Regulations System... Procedures to be followed when a contractor fails to perform. (a) The Contracting Officer shall initiate immediate action to protect the Government's rights whenever the contractor fails to comply with either the...

Some hospitals are falling behind in meeting 'meaningful use' criteria and could be vulnerable to penalties in 2015.

PubMed

DesRoches, Catherine M; Worzala, Chantal; Bates, Scott

2013-08-01

With nearly $30 billion in incentives available, it is critical to know to what extent US hospitals have been able to respond to those incentives by adopting electronic health record (EHR) systems that meet Medicare's criteria for their "meaningful use." Medicare has provided aggregate incentive payment data, but still missing is an understanding of how these payments are distributed across hospital types and years. Our analysis of Medicare data found a substantial increase in the percentage of hospitals receiving EHR incentive payments between 2011 (17.4 percent) and 2012 (36.8 percent). However, this increase was not uniform across all hospitals, and the overall proportion of hospitals receiving a payment for meaningful use was low. Critical-access, smaller, and publicly owned or nonprofit hospitals appeared to be at particular risk for failing to meet Medicare's meaningful-use criteria, and the overall proportion of hospitals receiving a payment for meaningful use was low. Starting in 2015, hospitals that fail to meet the criteria will be subject to financial penalties. To address the needs of institutions in danger of incurring these penalties, policy makers could implement targeted grant programs and provide additional information technology workforce support. In addition, the capacity of EHR system vendors should be carefully monitored to ensure that these institutions have access to the technology they need.

Impact of Smoke Exposure on Digital Instrumentation and Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanaka, Tina J.; Nowlen, Steven P.; Korsah, Kofi

2003-08-15

Smoke can cause interruptions and upsets in active electronics. Because nuclear power plants are replacing analog with digital instrumentation and control systems, qualification guidelines for new systems are being reviewed for severe environments such as smoke and electromagnetic interference. Active digital systems, individual components, and active circuits have been exposed to smoke in a program sponsored by the U.S. Nuclear Regulatory Commission. The circuits and systems were all monitored during the smoke exposure, indicating any immediate effects of the smoke. The results of previous smoke exposure studies have been reported in various publications. The major immediate effect of smoke hasmore » been to increase leakage currents and to cause momentary upsets and failures in digital systems. This paper presents new results from conformal coatings, memory chips, and hard drive tests.The best conformal coatings were found to be polyurethane, parylene, and acrylic (when applied by dipping). Conformal coatings can reduce smoke-induced leakage currents and protect against metal loss through corrosion. However conformal coatings are typically flammable, so they do increase material flammability. Some of the low-voltage biased memory chips failed during a combination of high smoke and high humidity. Typically, smoke along with heat and humidity is expected during fire, rather than smoke alone. Thus, due to high sensitivity of digital circuits to heat and humidity, it is hypothesized that the impact of smoke may be secondary.Low-voltage (3.3-V) static random-access memory (SRAMs) were found to be the most vulnerable to smoke. Higher bias voltages decrease the likelihood of failure. Erasable programmable read-only memory (EPROMs) and nonvolatile SRAMs were very smoke tolerant. Failures of the SRAMs occurred when two conditions were present: high density of smoke and high humidity. As the high humidity was present for only part of the test, the failures were intermittent. All of the chips that failed during the test recovered after enough venting.Hard disks were tested in severe environments but did not fail during the 2 h of monitoring.While the results of the tests documented in this report confirm that digital circuits can indeed be vulnerable to smoke, there is currently no practical, repeatable testing methodology, so it is not feasible to assess smoke susceptibility as part of environmental qualification. As a result, the most reasonable approach to minimizing smoke susceptibility is to employ design, implementation, and procedural practices that can reduce the possibility of smoke exposure and enhance smoke tolerance. Traditional approaches to mitigate its effects in digital safety instrumentation and control, such as redundancy, separation, defense in depth, as well as adherence to standards (e.g., the Institute of Electrical and Electronics Engineers' IEEE 384) and the Code of Federal Regulations Appendix R of 10 CFR 50, should continue to be applied.« less

Automatic protective vent has fail-safe feature

NASA Technical Reports Server (NTRS)

Dameron, C. E.

1966-01-01

Delayed vent valve system in a mechanical backing pump in a vacuum system allows the pneumatic foreline valve to seal before the pump vent opens. The system is designed to be fail-safe and operate even though there is loss of electrical power.

Fail-safe bidirectional valve driver

NASA Technical Reports Server (NTRS)

Fujimoto, H.

1974-01-01

Cross-coupled diodes are added to commonly used bidirectional valve driver circuit to protect circuit and power supply. Circuit may be used in systems requiring fail-safe bidirectional valve operation, particularly in chemical- and petroleum-processing control systems and computer-controlled hydraulic or pneumatic systems.

Fail Save Shut Off Valve for Filtering Systems Employing Candle Filters

DOEpatents

VanOsdol, John

2006-01-03

The invention relates to an apparatus that acts as a fail save shut off valve. More specifically, the invention relates to a fail save shut off valve that allows fluid flow during normal operational conditions, but prevents the flow of fluids in the event of system failure upstream that causes over-pressurization. The present invention is particularly well suited for use in conjunction with hot gas filtering systems, which utilize ceramic candle filters. Used in such a hot gas system the present invention stops the flow of hot gas and prevents any particulate laden gas from entering the clean side of the system.

Fail save shut off valve for filtering systems employing candle filters

DOEpatents

VanOsdol, John [Fairmont, WV

2006-01-03

The invention relates to an apparatus that acts as a fail save shut off valve. More specifically, the invention relates to a fail save shut off valve that allows fluid flow during normal operational conditions, but prevents the flow of fluids in the event of system failure upstream that causes over-pressurization. The present invention is particularly well suited for use in conjunction with hot gas filtering systems, which utilize ceramic candle filters. Used in such a hot gas system the present invention stops the flow of hot gas and prevents any particulate laden gas from entering the clean side of the system.

Public Notification - Revised Total Coliform Rule Failure To Report Template

EPA Pesticide Factsheets

When a PWS fails to report their monitoring results for Total Coliform bacteria, it must issue a public notice to inform consumers of its water of that failure to report. This template can be used as a guide for preparing that public notice.

40 CFR 63.8 - Monitoring requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... in the relevant standard; or (B) The CMS fails a performance test audit (e.g., cylinder gas audit), relative accuracy audit, relative accuracy test audit, or linearity test audit; or (C) The COMS CD exceeds...) Data recording, calculations, and reporting; (v) Accuracy audit procedures, including sampling and...

29 CFR 1910.95 - Occupational noise exposure.

Code of Federal Regulations, 2012 CFR

2012-07-01

... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Occupational Health and Environmental Control § 1910.95 Occupational... engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels of...) Monitoring shall be repeated whenever a change in production, process, equipment or controls increases noise...

29 CFR 1910.95 - Occupational noise exposure.

Code of Federal Regulations, 2014 CFR

2014-07-01

... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Occupational Health and Environmental Control § 1910.95 Occupational... engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels of...) Monitoring shall be repeated whenever a change in production, process, equipment or controls increases noise...

29 CFR 1910.95 - Occupational noise exposure.

Code of Federal Regulations, 2011 CFR

2011-07-01

... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Occupational Health and Environmental Control § 1910.95 Occupational... engineering controls shall be utilized. If such controls fail to reduce sound levels within the levels of...) Monitoring shall be repeated whenever a change in production, process, equipment or controls increases noise...

Endowments: Investing in the Future.

ERIC Educational Resources Information Center

O'Donnell, Michael; Ambler, Marjane

1996-01-01

Reports that tribal colleges face annual deficits since Congress fails to provide the support authorized by the Tribally Controlled Community College Assistance Act. Discusses the use of endowments as a means of covering those deficits, covering investment philosophies and policies, investment manager selection, and investment monitoring. (MAB)

Investigation of the Dayton IR 75 sign truss failure of 9/11/06.

DOT National Transportation Integrated Search

2007-03-01

Based upon a combination of in-situ field monitoring of traffic-induced bridge : vibrations at the location of the failed sign support truss, finite element simulation of the : expected dynamic response of the original truss in such an environment, t...

Study of a fail-safe abort system for an actively cooled hypersonic aircraft: Computer program documentation

NASA Technical Reports Server (NTRS)

Haas, L. A., Sr.

1976-01-01

The Fail-Safe Abort System TEMPerature Analysis Program, (FASTEMP), user's manual is presented. This program was used to analyze fail-safe abort systems for an actively cooled hypersonic aircraft. FASTEMP analyzes the steady state or transient temperature response of a thermal model defined in rectangular, cylindrical, conical and/or spherical coordinate system. FASTEMP provides the user with a large selection of subroutines for heat transfer calculations. The various modes of heat transfer available from these subroutines are: heat storage, conduction, radiation, heat addition or generation, convection, and fluid flow.

Correlating Transcription Initiation and Conformational Changes by a Single-Subunit RNA Polymerase with Near Base-Pair Resolution.

PubMed

Koh, Hye Ran; Roy, Rahul; Sorokina, Maria; Tang, Guo-Qing; Nandakumar, Divya; Patel, Smita S; Ha, Taekjip

2018-05-17

We provide a comprehensive analysis of transcription in real time by T7 RNA Polymerase (RNAP) using single-molecule fluorescence resonance energy transfer by monitoring the entire life history of transcription initiation, including stepwise RNA synthesis with near base-pair resolution, abortive cycling, and transition into elongation. Kinetically branching pathways were observed for abortive initiation with an RNAP either recycling on the same promoter or exchanging with another RNAP from solution. We detected fast and slow populations of RNAP in their transition into elongation, consistent with the efficient and delayed promoter release, respectively, observed in ensemble studies. Real-time monitoring of abortive cycling using three-probe analysis showed that the initiation events are stochastically branched into productive and failed transcription. The abortive products are generated primarily from initiation events that fail to progress to elongation, and a majority of the productive events transit to elongation without making abortive products. Copyright © 2018 Elsevier Inc. All rights reserved.

Adaptive voting computer system

NASA Technical Reports Server (NTRS)

Koczela, L. J.; Wilgus, D. S. (Inventor)

1974-01-01

A computer system is reported that uses adaptive voting to tolerate failures and operates in a fail-operational, fail-safe manner. Each of four computers is individually connected to one of four external input/output (I/O) busses which interface with external subsystems. Each computer is connected to receive input data and commands from the other three computers and to furnish output data commands to the other three computers. An adaptive control apparatus including a voter-comparator-switch (VCS) is provided for each computer to receive signals from each of the computers and permits adaptive voting among the computers to permit the fail-operational, fail-safe operation.

On damage detection in wind turbine gearboxes using outlier analysis

NASA Astrophysics Data System (ADS)

Antoniadou, Ifigeneia; Manson, Graeme; Dervilis, Nikolaos; Staszewski, Wieslaw J.; Worden, Keith

2012-04-01

The proportion of worldwide installed wind power in power systems increases over the years as a result of the steadily growing interest in renewable energy sources. Still, the advantages offered by the use of wind power are overshadowed by the high operational and maintenance costs, resulting in the low competitiveness of wind power in the energy market. In order to reduce the costs of corrective maintenance, the application of condition monitoring to gearboxes becomes highly important, since gearboxes are among the wind turbine components with the most frequent failure observations. While condition monitoring of gearboxes in general is common practice, with various methods having been developed over the last few decades, wind turbine gearbox condition monitoring faces a major challenge: the detection of faults under the time-varying load conditions prevailing in wind turbine systems. Classical time and frequency domain methods fail to detect faults under variable load conditions, due to the temporary effect that these faults have on vibration signals. This paper uses the statistical discipline of outlier analysis for the damage detection of gearbox tooth faults. A simplified two-degree-of-freedom gearbox model considering nonlinear backlash, time-periodic mesh stiffness and static transmission error, simulates the vibration signals to be analysed. Local stiffness reduction is used for the simulation of tooth faults and statistical processes determine the existence of intermittencies. The lowest level of fault detection, the threshold value, is considered and the Mahalanobis squared-distance is calculated for the novelty detection problem.

Monitoring robot actions for error detection and recovery

NASA Technical Reports Server (NTRS)

Gini, M.; Smith, R.

1987-01-01

Reliability is a serious problem in computer controlled robot systems. Although robots serve successfully in relatively simple applications such as painting and spot welding, their potential in areas such as automated assembly is hampered by programming problems. A program for assembling parts may be logically correct, execute correctly on a simulator, and even execute correctly on a robot most of the time, yet still fail unexpectedly in the face of real world uncertainties. Recovery from such errors is far more complicated than recovery from simple controller errors, since even expected errors can often manifest themselves in unexpected ways. Here, a novel approach is presented for improving robot reliability. Instead of anticipating errors, researchers use knowledge-based programming techniques so that the robot can autonomously exploit knowledge about its task and environment to detect and recover from failures. They describe preliminary experiment of a system that they designed and constructed.

Component Repair Times Obtained from MSPI Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eide, Steven A.; Cadwallader, Lee

Information concerning times to repair or restore equipment to service given a failure is valuable to probabilistic risk assessments (PRAs). Examples of such uses in modern PRAs include estimation of the probability of failing to restore a failed component within a specified time period (typically tied to recovering a mitigating system before core damage occurs at nuclear power plants) and the determination of mission times for support system initiating event (SSIE) fault tree models. Information on equipment repair or restoration times applicable to PRA modeling is limited and dated for U.S. commercial nuclear power plants. However, the Mitigating Systems Performancemore » Index (MSPI) program covering all U.S. commercial nuclear power plants provides up-to-date information on restoration times for a limited set of component types. This paper describes the MSPI program data available and analyzes the data to obtain median and mean component restoration times as well as non-restoration cumulative probability curves. The MSPI program provides guidance for monitoring both planned and unplanned outages of trains of selected mitigating systems deemed important to safety. For systems included within the MSPI program, plants monitor both train UA and component unreliability (UR) against baseline values. If the combined system UA and UR increases sufficiently above established baseline results (converted to an estimated change in core damage frequency or CDF), a “white” (or worse) indicator is generated for that system. That in turn results in increased oversight by the US Nuclear Regulatory Commission (NRC) and can impact a plant’s insurance rating. Therefore, there is pressure to return MSPI program components to service as soon as possible after a failure occurs. Three sets of unplanned outages might be used to determine the component repair durations desired in this article: all unplanned outages for the train type that includes the component of interest, only unplanned outages associated with failures of the component of interest, and only unplanned outages associated with PRA failures of the component of interest. The paper will describe how component repair times can be generated from each set and which approach is most applicable. Repair time information will be summarized for MSPI pumps and diesel generators using data over 2003 – 2007. Also, trend information over 2003 – 2012 will be presented to indicate whether the 2003 – 2007 repair time information is still considered applicable. For certain types of pumps, mean repair times are significantly higher than the typically assumed 24 h duration.« less

The use of morphokinetics as a predictor of embryo implantation.

PubMed

Meseguer, Marcos; Herrero, Javier; Tejera, Alberto; Hilligsøe, Karen Marie; Ramsing, Niels Birger; Remohí, Jose

2011-10-01

Time-lapse observation presents an opportunity for optimizing embryo selection based on morphological grading as well as providing novel kinetic parameters, which may further improve accurate selection of viable embryos. The objective of this retrospective study was to identify the morphokinetic parameters specific to embryos that were capable of implanting. In order to compare a large number of embryos, with minimal variation in culture conditions, we have used an automatic embryo monitoring system. Using a tri-gas IVF incubator with a built-in camera designed to automatically acquire images at defined time points, we have simultaneously monitored up to 72 individual embryos without removing the embryos from the controlled environment. Images were acquired every 15 min in five different focal planes for at least 64 h for each embryo. We have monitored the development of transferred embryos from 285 couples undergoing their first ICSI cycle. The total number of transferred embryos was 522, of which 247 either failed to implant or fully implanted, with full implantation meaning that all transferred embryos in a treatment implanted. A detailed retrospective analysis of cleavage times, blastomere size and multinucleation was made for the 247 transferred embryos with either failed or full implantation. We found that several parameters were significantly correlated with subsequent implantation (e.g. time of first and subsequent cleavages as well as the time between cleavages). The most predictive parameters were: (i) time of division to 5 cells, t5 (48.8-56.6 h after ICSI); (ii) time between division to 3 cells and subsequent division to 4 cells, s2 (≤ 0.76 h) and (iii) duration of cell cycle two, i.e. time between division to 2 cells and division to 3 cells, cc2 (≤ 11.9 h). We also observed aberrant behavior such as multinucleation at the 4 cell stage, uneven blastomere size at the 2 cell stage and abrupt cell division to three or more cells, which appeared to largely preclude implantation. The image acquisition and time-lapse analysis system makes it possible to determine exact timing of embryo cleavages in a clinical setting. We propose a multivariable model based on our findings to classify embryos according to their probability of implantation. The efficacy of this classification will be evaluated in a prospective randomized study that ultimately will determine if implantation rates can be improved by time-lapse analysis.

User-perceived reliability of unrepairable shared protection systems with functionally identical units

NASA Astrophysics Data System (ADS)

Ozaki, Hirokazu; Kara, Atsushi; Cheng, Zixue

2012-05-01

In this article, we investigate the reliability of M-for-N (M:N) shared protection systems. We focus on the reliability that is perceived by an end user of one of N units. We assume that any failed unit is instantly replaced by one of the M units (if available). We describe the effectiveness of such a protection system in a quantitative manner under the condition that the failed units are not repairable. Mathematical analysis gives the closed-form solution of the reliability and mean time to failure (MTTF). We also analyse several numerical examples of the reliability and MTTF. This result can be applied, for example, to the analysis and design of an integrated circuit consisting of redundant backup components. In such a device, repairing a failed component is unrealistic. The analysis provides useful information for the design for general shared protection systems in which the failed units are not repaired.

76 FR 73521 - Statutory Bar to Appointment of Persons Who Fail To Register Under Selective Service Law

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-29

... 3206-AM06 Statutory Bar to Appointment of Persons Who Fail To Register Under Selective Service Law... particular agency, if the agency fails to carry out the function in accordance with applicable law. If OPM... Selective Service System, but who knowingly and willfully failed to register before reaching age 26. The new...

40 CFR 205.171-8 - Passing or failing under SEA.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 26 2013-07-01 2013-07-01 false Passing or failing under SEA. 205.171... Passing or failing under SEA. (a) A failing exhaust system is one which, when installed on any motorcycle... equal to the number in Column A, the sample passes. (c) Pass or failure of a SEA takes place when a...

40 CFR 205.171-8 - Passing or failing under SEA.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Passing or failing under SEA. 205.171... Passing or failing under SEA. (a) A failing exhaust system is one which, when installed on any motorcycle... equal to the number in Column A, the sample passes. (c) Pass or failure of a SEA takes place when a...

40 CFR 205.171-8 - Passing or failing under SEA.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 26 2012-07-01 2011-07-01 true Passing or failing under SEA. 205.171-8... failing under SEA. (a) A failing exhaust system is one which, when installed on any motorcycle which is in... in Column A, the sample passes. (c) Pass or failure of a SEA takes place when a decision that an...

40 CFR 205.171-8 - Passing or failing under SEA.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Passing or failing under SEA. 205.171... Passing or failing under SEA. (a) A failing exhaust system is one which, when installed on any motorcycle... equal to the number in Column A, the sample passes. (c) Pass or failure of a SEA takes place when a...

40 CFR 205.171-8 - Passing or failing under SEA.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 25 2011-07-01 2011-07-01 false Passing or failing under SEA. 205.171... Passing or failing under SEA. (a) A failing exhaust system is one which, when installed on any motorcycle... equal to the number in Column A, the sample passes. (c) Pass or failure of a SEA takes place when a...

Assessment of three dead detector correction methods for cone-beam computed tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelms, David W.; Shukla, Hemant I.; Nixon, Earl

Purpose: Dead detectors due to manufacturing defects or radiation damage in the electronic portal imaging devices (EPIDs) used for cone-beam computed tomography (CBCT) can lead to image degradation and ring artifacts. In this work three dead detector correction methods were assessed using megavoltage CBCT (MVCBCT) as a test system, with the goals of assessing the relative effectiveness of the three methods and establishing the conditions for which they fail. Methods: MVCBCT projections acquired with four linacs at 8 and 60 MU (monitor units) were degraded with varying percentages (2%-95%) of randomly distributed dead single detectors (RDSs), randomly distributed dead detectormore » clusters (RDCs) of 2 mm diameter, and nonrandomly distributed dead detector disks (NRDDs) of varying diameter (4-16 mm). Correction algorithms were bidirectional linear interpolation (BLI), quad-directional linear interpolation (QLI), and a Laplacian solution (LS) method. Correction method failure was defined to occur if ring artifacts were present in the reconstructed phantom images from any linac or if the modulation transfer function (MTF) for any linac dropped below baseline with a p value, calculated with the two sample t test, of less than 0.01. Results: All correction methods failed at the same or lower RDC/RDS percentages and NRDD diameters for the 60 MU as for the 8 MU cases. The LS method tended to outperform or match the BLI and QLI methods. If ring artifacts anywhere in the images were considered unacceptable, the LS method failed for 60 MU at >33% RDS, >2% RDC, and >4 mm NRDD. If ring artifacts within 4 mm longitudinally of the phantom section interfaces were considered acceptable, the LS method failed for 60 MU at >90% RDS, >80% RDC, and >4 mm NRDD. LS failed due to MTF drop for 60 MU at >50% RDS, >25% RDC, and >4 mm NRDD. Conclusions: The LS method is superior to the BLI and QLI methods, and correction algorithm effectiveness decreases as imaging dose increases. All correction methods failed first due to ring artifacts and second due to MTF drop. If ring artifacts in axial slices within a 4 mm longitudinal distance from phantom section interfaces are acceptable, statistically significant loss in spatial resolution does not occur until over 25% of the EPID is covered in randomly distributed dead detectors, or NRDDs of 4 mm diameter are present.« less

Technical Leadership Development Program - Year 2

DTIC Science & Technology

2012-02-01

Why Projects Fail Pennotti Wed 2:45-3:00 Break Wed 3:00-4:30 Project: AR2D2: RFP Robinson UNCLASSIFIED Contract Number: H98230-08-D-0171 DO 02...Project: AR2D2 RFP 12. Customer Expectation-1: Lecture: Why Systems Fail 13. Customer Expectation-2: Case Study: Process Automation 14...01 February 2012 UNCLASSIFIED 65 Syllabus Segment 12: Why Systems Fail (Lecture) Time: 1.5 hours Responsible: Mike Pennotti Support

On-board fault diagnostics for fly-by-light flight control systems using neural network flight processors

NASA Astrophysics Data System (ADS)

Urnes, James M., Sr.; Cushing, John; Bond, William E.; Nunes, Steve

1996-10-01

Fly-by-Light control systems offer higher performance for fighter and transport aircraft, with efficient fiber optic data transmission, electric control surface actuation, and multi-channel high capacity centralized processing combining to provide maximum aircraft flight control system handling qualities and safety. The key to efficient support for these vehicles is timely and accurate fault diagnostics of all control system components. These diagnostic tests are best conducted during flight when all facts relating to the failure are present. The resulting data can be used by the ground crew for efficient repair and turnaround of the aircraft, saving time and money in support costs. These difficult to diagnose (Cannot Duplicate) fault indications average 40 - 50% of maintenance activities on today's fighter and transport aircraft, adding significantly to fleet support cost. Fiber optic data transmission can support a wealth of data for fault monitoring; the most efficient method of fault diagnostics is accurate modeling of the component response under normal and failed conditions for use in comparison with the actual component flight data. Neural Network hardware processors offer an efficient and cost-effective method to install fault diagnostics in flight systems, permitting on-board diagnostic modeling of very complex subsystems. Task 2C of the ARPA FLASH program is a design demonstration of this diagnostics approach, using the very high speed computation of the Adaptive Solutions Neural Network processor to monitor an advanced Electrohydrostatic control surface actuator linked through a AS-1773A fiber optic bus. This paper describes the design approach and projected performance of this on-line diagnostics system.

Instrumentation and control system architecture of ECRH SST1

NASA Astrophysics Data System (ADS)

Patel, Harshida; Patel, Jatin; purohit, Dharmesh; Shukla, B. K.; Babu, Rajan; Mistry, Hardik

2017-07-01

The Electron Cyclotron Resonance Heating (ECRH) system is an important heating system for the reliable start-up of tokamak. The 42GHz and 82.6GHz Gyrotron based ECRH systems are used in tokomaks SST-1 and Aditya to carry out ECRH related experiments. The Gyrotrons are high power microwave tubes used as a source for ECRH systems. The Gyrotrons need to be handled with optimum care right from the installation to its Full parameter control operation. The Gyrotrons are associated with the subsystems like: High voltage power supplies (Beam voltage and anode voltage), dedicated crowbar system, magnet, filament and ion pump power supplies and cooling system. The other subsystems are transmission line, launcher and dummy load. A dedicated VME based data acquisition & control (DAC) system is developed to operate and control the Gyrotron and its associated sub system. For the safe operation of Gyrotron, two level interlocks with fail-safe logic are developed. Slow signals that are operated in scale of millisecond range are programmed through software and hardware interlock in scale of microsecond range are designed and developed indigenously. Water-cooling and the associated interlock are monitored and control by data logger with independent human machine interface.

Modelling the tumour microenvironment in long-term microencapsulated 3D co-cultures recapitulates phenotypic features of disease progression.

PubMed

Estrada, Marta F; Rebelo, Sofia P; Davies, Emma J; Pinto, Marta T; Pereira, Hugo; Santo, Vítor E; Smalley, Matthew J; Barry, Simon T; Gualda, Emilio J; Alves, Paula M; Anderson, Elizabeth; Brito, Catarina

2016-02-01

3D cell tumour models are generated mainly in non-scalable culture systems, using bioactive scaffolds. Many of these models fail to reflect the complex tumour microenvironment and do not allow long-term monitoring of tumour progression. To overcome these limitations, we have combined alginate microencapsulation with agitation-based culture systems, to recapitulate and monitor key aspects of the tumour microenvironment and disease progression. Aggregates of MCF-7 breast cancer cells were microencapsulated in alginate, either alone or in combination with human fibroblasts, then cultured for 15 days. In co-cultures, the fibroblasts arranged themselves around the tumour aggregates creating distinct epithelial and stromal compartments. The presence of fibroblasts resulted in secretion of pro-inflammatory cytokines and deposition of collagen in the stromal compartment. Tumour cells established cell-cell contacts and polarised around small lumina in the interior of the aggregates. Over the culture period, there was a reduction in oestrogen receptor and membranous E-cadherin alongside loss of cell polarity, increased collective cell migration and enhanced angiogenic potential in co-cultures. These phenotypic alterations, typical of advanced stages of cancer, were not observed in the mono-cultures of MCF-7 cells. The proposed model system constitutes a new tool to study tumour-stroma crosstalk, disease progression and drug resistance mechanisms. Copyright © 2015 The Authors. Published by Elsevier Ltd.. All rights reserved.

The Standard Autonomous File Server, a Customized, Off-the-Shelf Success Story

NASA Technical Reports Server (NTRS)

Semancik, Susan K.; Conger, Annette M.; Obenschain, Arthur F. (Technical Monitor)

2001-01-01

The Standard Autonomous File Server (SAFS), which includes both off-the-shelf hardware and software, uses an improved automated file transfer process to provide a quicker, more reliable, prioritized file distribution for customers of near real-time data without interfering with the assets involved in the acquisition and processing of the data. It operates as a stand-alone solution, monitoring itself, and providing an automated fail-over process to enhance reliability. This paper will describe the unique problems and lessons learned both during the COTS selection and integration into SAFS, and the system's first year of operation in support of NASA's satellite ground network. COTS was the key factor in allowing the two-person development team to deploy systems in less than a year, meeting the required launch schedule. The SAFS system his been so successful, it is becoming a NASA standard resource, leading to its nomination for NASA's Software or the Year Award in 1999.

Potential fault region detection in TFDS images based on convolutional neural network

NASA Astrophysics Data System (ADS)

Sun, Junhua; Xiao, Zhongwen

2016-10-01

In recent years, more than 300 sets of Trouble of Running Freight Train Detection System (TFDS) have been installed on railway to monitor the safety of running freight trains in China. However, TFDS is simply responsible for capturing, transmitting, and storing images, and fails to recognize faults automatically due to some difficulties such as such as the diversity and complexity of faults and some low quality images. To improve the performance of automatic fault recognition, it is of great importance to locate the potential fault areas. In this paper, we first introduce a convolutional neural network (CNN) model to TFDS and propose a potential fault region detection system (PFRDS) for simultaneously detecting four typical types of potential fault regions (PFRs). The experimental results show that this system has a higher performance of image detection to PFRs in TFDS. An average detection recall of 98.95% and precision of 100% are obtained, demonstrating the high detection ability and robustness against various poor imaging situations.

An analysis of the early-warning system in emerging markets for reducing the financial crisis

NASA Astrophysics Data System (ADS)

Shen, Xiangguang; Song, Xiaozhong

2009-07-01

The large number of financial crises in emerging markets over the past ten years has left many observers, both from academia and financial institutions, puzzled by an apparent lack of homogenous causal relations between endogenous economic variables and the bursting of large financial shocks. The frequency of financial crises in the last 20 years can be attributed to the lack of a comprehensive theory of financial regulation to guide policy makers. Existing theories fail to define the range of regulatory models, the causes of regulatory failure, and how to measure and prevent it. Faulty design of regulatory models, and the lack of ongoing performance monitoring incorporating early warning systems, is disrupting economic and social development. The main aim of this article is to propose an early warning system (EWS) which purposes issuing warning signal against the possible financial crisis in the emerging market, and makes the emerging market survived the first wave of the crisis be able to continue their operation in the following years.

In-situ Fluorometers Reveal High Frequency Dynamics In Dissolved Organic Matter For Urban Rivers

NASA Astrophysics Data System (ADS)

Croghan, D.; Bradley, C.; Khamis, K.; Hannah, D. M.; Sadler, J. P.; Van Loon, A.

2017-12-01

To-date Dissolved Organic Matter (DOM) dynamics have been quantified poorly in urban rivers, despite the substantial water quality issues linked to urbanisation. Research has been hindered by the low temporal resolution of observations and over-reliance on manual sampling which often fail to capture precipitation events and diurnal dynamics. High frequency data are essential to estimate more accurately DOM fluxes/loads and to understand DOM furnishing and transport processes. Recent advances in optical sensor technology, including field deployable in-situ fluorometers, are yielding new high resolution DOM information. However, no consensus regarding the monitoring resolution required for urban systems exists, with no studies monitoring at <15 min time steps. High-frequency monitoring (5 min resolution; 4 week duration) was conducted on a headwater urban stream in Birmingham, UK (N 52.447430 W -1.936715) to determine the optimum temporal resolution for characterization of DOM event dynamics. A through-flow GGNU-30 monitored wavelengths corresponding to tryptophan-like fluorescence (TLF; Peak T1) (Ex 285 nm/ Em 345 nm) and humic-like fluorescence (HLF; Peak C) (Ex 365 nm/Em 490 nm). The results suggest that at base flow TLF and HLF are relatively stable, though episodic DOM inputs can pulse through the system, which may be missed during lower temporal resolution monitoring. High temporal variation occurs during storm events in TLF and HLF intensity: TLF intensity is highest during the rising limb of the hydrograph and can rapidly decline thereafter, indicating the importance of fast flow-path and close proximity sources to TLF dynamics. HLF intensity tracks discharge more closely, but can also quickly decline during high flow events due to dilution effects. Furthermore, the ratio of TLF:HLF when derived at high-frequency provides a useful indication of the presence and type of organic effluents in stream, which aids in the identification of Combined Sewage Overflow releases. Our work highlights the need for future studies to utilise shorter temporal scales than previously used to monitor urban DOM dynamics. The application of higher frequency monitoring enables the identification of finer-scale patterns and subsequently aids in deciphering the sources and pathways controlling urban DOM dynamics.

How change management can prevent the failure of information systems implementation among Malaysian government hospitals?

NASA Astrophysics Data System (ADS)

ChePa, Noraziah; Jasin, Noorhayati Md; Bakar, Nur Azzah Abu

2017-10-01

Fail to prevent or control challenges of Information System (IS) implementation have led to the failure of its implementation. Successful implementation of IS has been a challenging task to any organization including government hospitals. Government has invested a big amount of money on information system (IS) projects to improve service delivery in healthcare. However, several of them failed to be implemented successfully due to several factors. This article proposes a prevention model which incorporated Change Management (CM) concepts to avoid the failure of IS implementation, hence ensuring the success of it. Challenges of IS implementation in government hospitals have been discovered. Extensive literature review and deep interview approaches were employed to discover these challenges. A prevention model has been designed to cater the challenges. The model caters three main phases of implementation; pre-implementation, during implementation, and post-implementation by adopting CM practices of Lewin's, Kotter's and Prosci's CM model. Six elements of CM comprising thirteen sub-elements adopted from the three CM models have been used to handle CFFs of Human and Support issues; guiding team, resistance avoidance, IS adoption, enforcement, monitoring, and IS sustainability. Successful practice of the proposed mapping is expected to prevent CFFs to occur, hence ensuring a successful implementation of IS in the hospitals. The proposed model has been presented and successfully evaluated by the domain experts from the selected hospitals. The proposed model is believed to be beneficial for top management, IT practitioners and medical practitioners in preventing IS implementation failure among government hospitals towards ensuring the success implementation.

Intrinsic cardiac nervous system in tachycardia induced heart failure.

PubMed

Arora, Rakesh C; Cardinal, Rene; Smith, Frank M; Ardell, Jeffrey L; Dell'Italia, Louis J; Armour, J Andrew

2003-11-01

The purpose of this study was to test the hypothesis that early-stage heart failure differentially affects the intrinsic cardiac nervous system's capacity to regulate cardiac function. After 2 wk of rapid ventricular pacing in nine anesthetized canines, cardiac and right atrial neuronal function were evaluated in situ in response to enhanced cardiac sensory inputs, stimulation of extracardiac autonomic efferent neuronal inputs, and close coronary arterial administration of neurochemicals that included nicotine. Right atrial neuronal intracellular electrophysiological properties were then evaluated in vitro in response to synaptic activation and nicotine. Intrinsic cardiac nicotine-sensitive, neuronally induced cardiac responses were also evaluated in eight sham-operated, unpaced animals. Two weeks of rapid ventricular pacing reduced the cardiac index by 54%. Intrinsic cardiac neurons of paced hearts maintained their cardiac mechano- and chemosensory transduction properties in vivo. They also responded normally to sympathetic and parasympathetic preganglionic efferent neuronal inputs, as well as to locally administered alpha-or beta-adrenergic agonists or angiotensin II. The dose of nicotine needed to modify intrinsic cardiac neurons was 50 times greater in failure compared with normal preparations. That dose failed to alter monitored cardiovascular indexes in failing preparations. Phasic and accommodating neurons identified in vitro displayed altered intracellular membrane properties compared with control, including decreased membrane resistance, indicative of reduced excitability. Early-stage heart failure differentially affects the intrinsic cardiac nervous system's capacity to regulate cardiodynamics. While maintaining its capacity to transduce cardiac mechano- and chemosensory inputs, as well as inputs from extracardiac autonomic efferent neurons, intrinsic cardiac nicotine-sensitive, local-circuit neurons differentially remodel such that their capacity to influence cardiodynamics becomes obtunded.

42 CFR 425.316 - Monitoring of ACOs.

Code of Federal Regulations, 2013 CFR

2013-10-01

... quality measurement data reported by the ACO as well as aggregate annual and quarterly reports. (ii... described in paragraph (a)(2) of this section (as appropriate) to identify trends and patterns suggesting... quality performance standards or fails to report on one or more quality measures, in addition to actions...

42 CFR 425.316 - Monitoring of ACOs.

Code of Federal Regulations, 2014 CFR

2014-10-01

... quality measurement data reported by the ACO as well as aggregate annual and quarterly reports. (ii... described in paragraph (a)(2) of this section (as appropriate) to identify trends and patterns suggesting... quality performance standards or fails to report on one or more quality measures, in addition to actions...

42 CFR 425.316 - Monitoring of ACOs.

Code of Federal Regulations, 2012 CFR

2012-10-01

... quality measurement data reported by the ACO as well as aggregate annual and quarterly reports. (ii... described in paragraph (a)(2) of this section (as appropriate) to identify trends and patterns suggesting... quality performance standards or fails to report on one or more quality measures, in addition to actions...

7 CFR 718.103 - Prevented planted and failed acreage.

Code of Federal Regulations, 2014 CFR

2014-01-01

... prevented-planted acreage was affected by drought, unless: (1) On the final planting date for non-irrigated.... Drought Monitor; and (3) Verifiable information is collected from sources whose business or purpose it is... a lack of water resulting from drought conditions or contamination by saltwater intrusion of an...

7 CFR 718.103 - Prevented planted and failed acreage.

Code of Federal Regulations, 2010 CFR

2010-01-01

... prevented-planted acreage was affected by drought, unless: (1) On the final planting date for non-irrigated.... Drought Monitor; and (3) Verifiable information is collected from sources whose business or purpose it is... a lack of water resulting from drought conditions or contamination by saltwater intrusion of an...

7 CFR 718.103 - Prevented planted and failed acreage.

Code of Federal Regulations, 2013 CFR

2013-01-01

... prevented-planted acreage was affected by drought, unless: (1) On the final planting date for non-irrigated.... Drought Monitor; and (3) Verifiable information is collected from sources whose business or purpose it is... a lack of water resulting from drought conditions or contamination by saltwater intrusion of an...

7 CFR 718.103 - Prevented planted and failed acreage.

Code of Federal Regulations, 2012 CFR

2012-01-01

... prevented-planted acreage was affected by drought, unless: (1) On the final planting date for non-irrigated.... Drought Monitor; and (3) Verifiable information is collected from sources whose business or purpose it is... a lack of water resulting from drought conditions or contamination by saltwater intrusion of an...

7 CFR 718.103 - Prevented planted and failed acreage.

Code of Federal Regulations, 2011 CFR

2011-01-01

... prevented-planted acreage was affected by drought, unless: (1) On the final planting date for non-irrigated.... Drought Monitor; and (3) Verifiable information is collected from sources whose business or purpose it is... a lack of water resulting from drought conditions or contamination by saltwater intrusion of an...

78 FR 77755 - Self-Regulatory Organizations; The Depository Trust Company; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-24

... to adequately implement anti-money laundering procedures by failing adequately to perform due...-priced and thinly traded securities'' implicates anti-money laundering monitoring concerns.\\15\\ \\15... Role of Domestic Shell Companies in Financial Crime and Money Laundering (2006), available at http...

40 CFR 63.8 - Monitoring requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... with conducting performance tests under § 63.7. Verification of operational status shall, at a minimum... in the relevant standard; or (B) The CMS fails a performance test audit (e.g., cylinder gas audit), relative accuracy audit, relative accuracy test audit, or linearity test audit; or (C) The COMS CD exceeds...

40 CFR 63.8 - Monitoring requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... with conducting performance tests under § 63.7. Verification of operational status shall, at a minimum... in the relevant standard; or (B) The CMS fails a performance test audit (e.g., cylinder gas audit), relative accuracy audit, relative accuracy test audit, or linearity test audit; or (C) The COMS CD exceeds...

Investigation of the Dayton IR 75 sign truss failure of 9/11/06 : executive summary.

DOT National Transportation Integrated Search

2007-03-01

Based upon a combination of in-situ field monitoring of traffic-induced bridge vibrations at the location of the failed sign support truss, finite element simulation of the expected dynamic response of the original truss in such an environment, the l...

Vigilance impossible: Diligence, distraction, and daydreaming all lead to failures in a practical monitoring task.

PubMed

Casner, Stephen M; Schooler, Jonathan W

2015-09-01

In laboratory studies of vigilance, participants watch for unusual events in a "sit and stare" fashion as their performance typically declines over time. But watch keepers in practical settings seldom approach monitoring in such simplistic ways and controlled environments. We observed airline pilots performing routine monitoring duties in the cockpit. Unlike laboratory studies, pilots' monitoring did not deteriorate amidst prolonged vigils. Monitoring was frequently interrupted by other pop-up tasks and misses followed. However, when free from these distractions, pilots reported copious mind wandering. Pilots often confined their mind wandering to times in which their monitoring performance would not conspicuously suffer. But when no convenient times were available, pilots mind wandered anyway and misses ensued. Real-world monitors may be caught between a continuous vigilance approach that is doomed to fail, a dynamic environment that cannot be fully controlled, and what may be an irresistible urge to let one's thoughts drift. Published by Elsevier Inc.

On the role of model-based monitoring for adaptive planning under uncertainty

NASA Astrophysics Data System (ADS)

Raso, Luciano; Kwakkel, Jan; Timmermans, Jos; Haasnoot, Mariolijn

2016-04-01

Adaptive plans, designed to anticipate and respond to an unfolding uncertain future, have found a fertile application domain in the planning of deltas that are exposed to rapid socioeconomic development and climate change. Adaptive planning, under the moniker of adaptive delta management, is used in the Dutch Delta Program for developing a nation-wide plan to prepare for uncertain climate change and socio-economic developments. Scientifically, adaptive delta management relies heavily on Dynamic Adaptive Policy Pathways. Currently, in the Netherlands the focus is shifting towards implementing the adaptive delta plan. This shift is especially relevant because the efficacy of adaptive plans hinges on monitoring on-going developments and ensuring that actions are indeed taken if and when necessary. In the design of an effective monitoring system for an adaptive plan, three challenges have to be confronted: • Shadow of the past: The development of adaptive plans and the design of their monitoring system relies heavily on current knowledge of the system, and current beliefs about plausible future developments. A static monitoring system is therefore exposed to the exact same uncertainties one tries to address through adaptive planning. • Inhibition of learning: Recent applications of adaptive planning tend to overlook the importance of learning and new information, and fail to account for this explicitly in the design of adaptive plans. • Challenge of surprise: Adaptive policies are designed in light of the current foreseen uncertainties. However, developments that are not considered during the design phase as being plausible could still substantially affect the performance of adaptive policies. The shadow of the past, the inhibition of learning, and the challenge of surprise taken together suggest that there is a need for redesigning the concepts of monitoring and evaluation to support the implementation of adaptive plans. Innovations from control theory, triggered by the challenge of uncertainty in operational control, may offer solutions from which monitoring for adaptive planning can benefit. Specifically: (i) in control, observations are incorporated into the model through data assimilation, updating the present state, boundary conditions, and parameters based on new observations, diminishing the shadow of the past; (ii) adaptive control is a way to modify the characteristics of the internal model, incorporating new knowledge on the system, countervailing the inhibition of learning; and (iii) in closed-loop control, a continuous system update equips the controller with "inherent robustness", i.e. to capacity to adapts to new conditions even when these were not initially considered. We aim to explore how inherent robustness addresses the challenge of surprise. Innovations in model-based control might help to improve and adapt the models used to support adaptive delta management to new information (reducing uncertainty). Moreover, this would offer a starting point for using these models not only in the design of adaptive plans, but also as part of the monitoring. The proposed research requires multidisciplinary cooperation between control theory, the policy sciences, and integrated assessment modeling.

Systems Engineering Technical Leadership Development Program

DTIC Science & Technology

2012-02-01

leading others in creative problem solving, complexity, and why projects fail . These topics were additionally supported by case studies designed to...Your Core Values Dominick Wed 12:30-1:30 Lunch Wed 1:30-2:45 Case Study: Why Projects Fail Pennotti Wed 2:45-3:00 Break Wed 3:00-4:30 Project...Case Study: When Good Wasn’t Good Enough 11. Technical Value-5: Group Project: AR2D2 RFP 12. Customer Expectation-1: Lecture: Why Systems Fail

Thermal compatibility of dental ceramic systems using cylindrical and spherical geometries.

PubMed

DeHoff, Paul H; Barrett, Allyson A; Lee, Robert B; Anusavice, Kenneth J

2008-06-01

To test the hypothesis that bilayer ceramic cylinders and spheres can provide valid confirmation of thermal incompatibility stresses predicted by finite element analyses. A commercial core ceramic and an experimental core ceramic were used to fabricate open-ended cylinders and core ceramic spheres. The core cylinders and spheres were veneered with one of four commercial dental ceramics representing four thermally compatible groups and four thermally incompatible groups. Axisymmetric thermal and viscoelastic elements in the ANSYS finite element program were used to calculate temperatures and stresses for each geometry and ceramic combination. This process required a transient heat transfer analysis for each combination to determine input temperatures for the structural model. After fabrication, each specimen was examined visually using fiberoptic transillumination for evidence of cracking. There were 100% failures of the thermally incompatible cylinders while none of the thermally compatible combinations failed. Among the spheres, 100% of the thermally incompatible systems failed, 16% of one of the thermally compatible systems failed, and none of the remaining compatible combinations failed. The calculated stress values were in general agreement with the experimental observations, i.e., low residual stresses for the specimens that did not fail and high residual stresses for the specimens that did fail. Simple screening geometries can be used to identify highly incompatible ceramic combinations, but they do not identify marginally incompatible systems.

Thermal compatibility of dental ceramic systems using cylindrical and spherical geometries

PubMed Central

DeHoff, Paul H.; Barrett, Allyson A.; Lee, Robert B.; Anusavice, Kenneth J.

2009-01-01

Objective To test the hypothesis that bilayer ceramic cylinders and spheres can provide valid confirmation of thermal incompatibility stresses predicted by finite element analyses. Methods A commercial core ceramic and an experimental core ceramic were used to fabricate open-ended cylinders and core ceramic spheres. The core cylinders and spheres were veneered with one of four commercial dental ceramics representing four thermally compatible groups and four thermally incompatible groups. Axisymmetric thermal and viscoelastic elements in the ANSYS finite element program were used to calculate temperatures and stresses for each geometry and ceramic combination. This process required a transient heat transfer analysis for each combination to determine input temperatures for the structural model. Results After fabrication, each specimen was examined visually using fiberoptic transillumination for evidence of cracking. There were 100% failures of the thermally incompatible cylinders while none of the thermally compatible combinations failed. Among the spheres, 100% of the thermally incompatible systems failed, 16% of one of the thermally compatible systems failed, and none of the remaining compatible combinations failed. The calculated stress values were in general agreement with the experimental observations, i.e., low residual stresses for the specimens that did not fail and high residual stresses for the specimens that did fail. Significance Simple screening geometries can be used to identify highly incompatible ceramic combinations, but they do not identify marginally incompatible systems. PMID:17949805

High Temporal and Spatial Resolution Coverage of Earth from Commercial AVSTAR Systems in Geostationary Orbit

NASA Astrophysics Data System (ADS)

Lecompte, M. A.; Heaps, J. F.; Williams, F. H.

Imaging the earth from Geostationary Earth Orbit (GEO) allows frequent updates of environmental conditions within an observable hemisphere at time and spatial scales appropriate to the most transient observable terrestrial phenomena. Coverage provided by current GEO Meteorological Satellites (METSATS) fails to fully exploit this advantage due primarily to obsolescent technology and also institutional inertia. With the full benefit of GEO based imaging unrealized, rapidly evolving phenomena, occurring at the smallest spatial and temporal scales that frequently have significant environmental impact remain unobserved. These phenomena may be precursors for the most destructive natural processes that adversely effect society. Timely distribution of information derived from "real-time" observations thus may provide opportunities to mitigate much of the damage to life and property that would otherwise occur. AstroVision International's AVStar Earth monitoring system is designed to overcome the current limitations if GEO Earth coverage and to provide real time monitoring of changes to the Earth's complete atmospheric, land and marine surface environments including fires, volcanic events, lightning and meteoritic events on a "live," true color, and multispectral basis. The understanding of severe storm dynamics and its coupling to the earth's electro-sphere will be greatly enhanced by observations at unprecedented sampling frequencies and spatial resolution. Better understanding of these natural phenomena and AVStar operational real-time coverage may also benefit society through improvements in severe weather prediction and warning. AstroVision's AVStar system, designed to provide this capability with the first of a constellation of GEO- based commercial environmental monitoring satellites to be launched in late 2003 will be discussed, including spatial and temporal resolution, spectral coverage with applications and an inventory of the potential benefits to society, science, commerce and education.

Fluoride tracer test for the performance analysis of a basin used as a lagooning pre-treatment facility in a WTP.

PubMed

Ruffino, Barbara

2015-07-01

The water treatment plant (WTP) of the city of Torino (NW Italy), which treats about 40 · 10(6) m(3)/year of raw water from Po river, has a 15-ha basin used as a lagooning pre-treatment facility. Since the efficiency of the lagooning process in the removal of pollutants from raw water depends on the internal hydrodynamics of the basin, the hydraulic performance of the basin was studied by combining the results of a stimulus-response tracer test with the monitoring of the tracer (fluoride) concentration throughout the basin at different times. The outcomes of the test demonstrated that the system was efficiently mixed and could be assimilated to a continuous stirred reactor presenting no flow anomalies, with an actual mean residence time (RT) of 12.7 days, compared with a nominal RT of 18 days. This assured that dissolved contaminants (such as fluoride) coming from the river were efficiently diluted before entering the WTP. The axial dispersion coefficient calculated from the RT distribution was approximately 47,300 m(2)/day. Three of the most popular formulae developed for the calculation of the axial dispersion coefficient provided results spreading over three orders of magnitude, thus showing their limitations. Finally, because of the width extent of the basin and the characteristics of its inflow, the 1-D advection-dispersion model failed in predicting the tracer concentration values in time at the outlet channel. On the contrary, the analytical solution of the 2-D advection-dispersion model proved to be suitable to fit the tracer concentration data over time at the outlet channel but it failed in describing the tracer distribution throughout the basin on the monitoring dates.

ATP monitoring technology for microbial growth control in potable water systems

NASA Astrophysics Data System (ADS)

Whalen, Patrick A.; Whalen, Philip J.; Cairns, James E.

2006-05-01

ATP (Adenosine Triphosphate) is the primary energy transfer molecule present in all living biological cells on Earth. ATP cannot be produced or maintained by anything but a living organism, and as such, its measurement is a direct indication of biological activity. The main advantage of ATP as a biological indicator is the speed of the analysis - from collecting the sample to obtaining the result, only minutes are required. The technology to measure ATP is already widely utilized to verify disinfection efficacy in the food industry and is also commonly applied in industrial water processes such as cooling water systems to monitor microbial growth and biocide applications. Research has indicated that ATP measurement technology can also play a key role in such important industries as potable water distribution and biological wastewater treatment. As will be detailed in this paper, LuminUltra Technologies has developed and applied ATP measurement technologies designed for any water type, and as such can provide a method to rapidly and accurately determine the level of biological activity in drinking water supplies. Because of its speed and specificity to biological activity, ATP measurement can play a key role in defending against failing drinking water quality, including those encountered during routine operation and also bioterrorism.

OPERATIONAL EXPERIENCE WITH FAST FIBER-OPTIC BEAM LOSS MONITORS FOR THE ADVANCED PHOTON SOURCE STORAGE RING SUPERCONDUCTING UNDULATORS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dooling, J.; Harkay, K.; Sajaev, V.

Fast fiber-optic (FFO) beam loss monitors (BLMs) installed with the first two superconducting undulators (SCUs) in the Advanced Photon Source storage ring have proven to be a useful diagnostic for measuring deposited charge (energy) during rapid beam loss events. The first set of FFOBLMs were installed outside the cryostat of the short SCU, a 0.33-m long device, above and below the beam centerline. The second set are mounted with the first 1.1-mlong SCU within the cryostat, on the outboard and inboard sides of the vacuum chamber. The next 1.1-m-long SCU is scheduled to replace the short SCU later in 2016more » and will be fitted with FFOBLMs in a manner similar to original 1.1-m device. The FFOBLMs were employed to set timing and voltage for the abort kicker (AK) system. The AK helps to prevent quenching of the SCUs during beam dumps [1] by directing the beam away from the SC magnet windings. The AK is triggered by the Machine Protection System (MPS). In cases when the AK fails to prevent quenching, the FFOBLMs show that losses often begin before detection by the MPS.« less

Methylxanthine Drug Monitoring with Wearable Sweat Sensors.

PubMed

Tai, Li-Chia; Gao, Wei; Chao, Minghan; Bariya, Mallika; Ngo, Quynh P; Shahpar, Ziba; Nyein, Hnin Y Y; Park, Hyejin; Sun, Junfeng; Jung, Younsu; Wu, Eric; Fahad, Hossain M; Lien, Der-Hsien; Ota, Hiroki; Cho, Gyoujin; Javey, Ali

2018-06-01

Drug monitoring plays crucial roles in doping control and precision medicine. It helps physicians tailor drug dosage for optimal benefits, track patients' compliance to prescriptions, and understand the complex pharmacokinetics of drugs. Conventional drug tests rely on invasive blood draws. While urine and sweat are attractive alternative biofluids, the state-of-the-art methods require separate sample collection and processing steps and fail to provide real-time information. Here, a wearable platform equipped with an electrochemical differential pulse voltammetry sensing module for drug monitoring is presented. A methylxanthine drug, caffeine, is selected to demonstrate the platform's functionalities. Sweat caffeine levels are monitored under various conditions, such as drug doses and measurement time after drug intake. Elevated sweat caffeine levels upon increasing dosage and confirmable caffeine physiological trends are observed. This work leverages a wearable sweat sensing platform toward noninvasive and continuous point-of-care drug monitoring and management. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Covert video monitoring in the assessment of medically unexplained symptoms in children.

PubMed

Wallace, Dustin P; Sim, Leslie A; Harrison, Tracy E; Bruce, Barbara K; Harbeck-Weber, Cynthia

2012-04-01

Diagnosis of medically unexplained symptoms (MUS) occurs after thorough evaluations have failed to identify a physiological cause for symptoms. However, families and providers may wonder if something has been missed, leading to reduced confidence in behavioral treatment. Confidence may be improved through the use of technology such as covert video monitoring to better assess functioning across settings. A 12-year-old male presented with progressive neurological decline, precipitated by chronic pain. After thorough evaluation and the failure of standard treatments (medical, rehabilitative, and psychological) covert video monitoring revealed that the patient demonstrated greater abilities when alone in his room. Negative reinforcement was used to initiate recovery, accompanied by positive reinforcement and a rehabilitative approach. Covert video monitoring assisted in three subsequent cases over the following 3 years. In certain complex cases, video monitoring can inform the assessment and treatment of MUS. Discussion includes ethical and practical considerations.

A secure and efficient uniqueness-and-anonymity-preserving remote user authentication scheme for connected health care.

PubMed

Das, Ashok Kumar; Goswami, Adrijit

2013-06-01

Connected health care has several applications including telecare medicine information system, personally controlled health records system, and patient monitoring. In such applications, user authentication can ensure the legality of patients. In user authentication for such applications, only the legal user/patient himself/herself is allowed to access the remote server, and no one can trace him/her according to transmitted data. Chang et al. proposed a uniqueness-and-anonymity-preserving remote user authentication scheme for connected health care (Chang et al., J Med Syst 37:9902, 2013). Their scheme uses the user's personal biometrics along with his/her password with the help of the smart card. The user's biometrics is verified using BioHashing. Their scheme is efficient due to usage of one-way hash function and exclusive-or (XOR) operations. In this paper, we show that though their scheme is very efficient, their scheme has several security weaknesses such as (1) it has design flaws in login and authentication phases, (2) it has design flaws in password change phase, (3) it fails to protect privileged insider attack, (4) it fails to protect the man-in-the middle attack, and (5) it fails to provide proper authentication. In order to remedy these security weaknesses in Chang et al.'s scheme, we propose an improvement of their scheme while retaining the original merit of their scheme. We show that our scheme is efficient as compared to Chang et al.'s scheme. Through the security analysis, we show that our scheme is secure against possible attacks. Further, we simulate our scheme for the formal security verification using the widely-accepted AVISPA (Automated Validation of Internet Security Protocols and Applications) tool to ensure that our scheme is secure against passive and active attacks. In addition, after successful authentication between the user and the server, they establish a secret session key shared between them for future secure communication.

A secure user anonymity-preserving three-factor remote user authentication scheme for the telecare medicine information systems.

PubMed

Das, Ashok Kumar

2015-03-01

Recent advanced technology enables the telecare medicine information system (TMIS) for the patients to gain the health monitoring facility at home and also to access medical services over the Internet of mobile networks. Several remote user authentication schemes have been proposed in the literature for TMIS. However, most of them are either insecure against various known attacks or they are inefficient. Recently, Tan proposed an efficient user anonymity preserving three-factor authentication scheme for TMIS. In this paper, we show that though Tan's scheme is efficient, it has several security drawbacks such as (1) it fails to provide proper authentication during the login phase, (2) it fails to provide correct updation of password and biometric of a user during the password and biometric update phase, and (3) it fails to protect against replay attack. In addition, Tan's scheme lacks the formal security analysis and verification. Later, Arshad and Nikooghadam also pointed out some security flaws in Tan's scheme and then presented an improvement on Tan's s scheme. However, we show that Arshad and Nikooghadam's scheme is still insecure against the privileged-insider attack through the stolen smart-card attack, and it also lacks the formal security analysis and verification. In order to withstand those security loopholes found in both Tan's scheme, and Arshad and Nikooghadam's scheme, we aim to propose an effective and more secure three-factor remote user authentication scheme for TMIS. Our scheme provides the user anonymity property. Through the rigorous informal and formal security analysis using random oracle models and the widely-accepted AVISPA (Automated Validation of Internet Security Protocols and Applications) tool, we show that our scheme is secure against various known attacks, including the replay and man-in-the-middle attacks. Furthermore, our scheme is also efficient as compared to other related schemes.

Sonification of network traffic flow for monitoring and situational awareness

PubMed Central

2018-01-01

Maintaining situational awareness of what is happening within a computer network is challenging, not only because the behaviour happens within machines, but also because data traffic speeds and volumes are beyond human ability to process. Visualisation techniques are widely used to present information about network traffic dynamics. Although they provide operators with an overall view and specific information about particular traffic or attacks on the network, they often still fail to represent the events in an understandable way. Also, because they require visual attention they are not well suited to continuous monitoring scenarios in which network administrators must carry out other tasks. Here we present SoNSTAR (Sonification of Networks for SiTuational AwaReness), a real-time sonification system for monitoring computer networks to support network administrators’ situational awareness. SoNSTAR provides an auditory representation of all the TCP/IP traffic within a network based on the different traffic flows between between network hosts. A user study showed that SoNSTAR raises situational awareness levels by enabling operators to understand network behaviour and with the benefit of lower workload demands (as measured by the NASA TLX method) than visual techniques. SoNSTAR identifies network traffic features by inspecting the status flags of TCP/IP packet headers. Combinations of these features define particular traffic events which are mapped to recorded sounds to generate a soundscape that represents the real-time status of the network traffic environment. The sequence, timing, and loudness of the different sounds allow the network to be monitored and anomalous behaviour to be detected without the need to continuously watch a monitor screen. PMID:29672543

Sonification of network traffic flow for monitoring and situational awareness.

PubMed

Debashi, Mohamed; Vickers, Paul

2018-01-01

Maintaining situational awareness of what is happening within a computer network is challenging, not only because the behaviour happens within machines, but also because data traffic speeds and volumes are beyond human ability to process. Visualisation techniques are widely used to present information about network traffic dynamics. Although they provide operators with an overall view and specific information about particular traffic or attacks on the network, they often still fail to represent the events in an understandable way. Also, because they require visual attention they are not well suited to continuous monitoring scenarios in which network administrators must carry out other tasks. Here we present SoNSTAR (Sonification of Networks for SiTuational AwaReness), a real-time sonification system for monitoring computer networks to support network administrators' situational awareness. SoNSTAR provides an auditory representation of all the TCP/IP traffic within a network based on the different traffic flows between between network hosts. A user study showed that SoNSTAR raises situational awareness levels by enabling operators to understand network behaviour and with the benefit of lower workload demands (as measured by the NASA TLX method) than visual techniques. SoNSTAR identifies network traffic features by inspecting the status flags of TCP/IP packet headers. Combinations of these features define particular traffic events which are mapped to recorded sounds to generate a soundscape that represents the real-time status of the network traffic environment. The sequence, timing, and loudness of the different sounds allow the network to be monitored and anomalous behaviour to be detected without the need to continuously watch a monitor screen.

Live Imaging Followed by Single Cell Tracking to Monitor Cell Biology and the Lineage Progression of Multiple Neural Populations.

PubMed

Gómez-Villafuertes, Rosa; Paniagua-Herranz, Lucía; Gascon, Sergio; de Agustín-Durán, David; Ferreras, María de la O; Gil-Redondo, Juan Carlos; Queipo, María José; Menendez-Mendez, Aida; Pérez-Sen, Ráquel; Delicado, Esmerilda G; Gualix, Javier; Costa, Marcos R; Schroeder, Timm; Miras-Portugal, María Teresa; Ortega, Felipe

2017-12-16

Understanding the mechanisms that control critical biological events of neural cell populations, such as proliferation, differentiation, or cell fate decisions, will be crucial to design therapeutic strategies for many diseases affecting the nervous system. Current methods to track cell populations rely on their final outcomes in still images and they generally fail to provide sufficient temporal resolution to identify behavioral features in single cells. Moreover, variations in cell death, behavioral heterogeneity within a cell population, dilution, spreading, or the low efficiency of the markers used to analyze cells are all important handicaps that will lead to incomplete or incorrect read-outs of the results. Conversely, performing live imaging and single cell tracking under appropriate conditions represents a powerful tool to monitor each of these events. Here, a time-lapse video-microscopy protocol, followed by post-processing, is described to track neural populations with single cell resolution, employing specific software. The methods described enable researchers to address essential questions regarding the cell biology and lineage progression of distinct neural populations.

Precursory changes in seismic velocity for the spectrum of earthquake failure modes

PubMed Central

Scuderi, M.M.; Marone, C.; Tinti, E.; Di Stefano, G.; Collettini, C.

2016-01-01

Temporal changes in seismic velocity during the earthquake cycle have the potential to illuminate physical processes associated with fault weakening and connections between the range of fault slip behaviors including slow earthquakes, tremor and low frequency earthquakes1. Laboratory and theoretical studies predict changes in seismic velocity prior to earthquake failure2, however tectonic faults fail in a spectrum of modes and little is known about precursors for those modes3. Here we show that precursory changes of wave speed occur in laboratory faults for the complete spectrum of failure modes observed for tectonic faults. We systematically altered the stiffness of the loading system to reproduce the transition from slow to fast stick-slip and monitored ultrasonic wave speed during frictional sliding. We find systematic variations of elastic properties during the seismic cycle for both slow and fast earthquakes indicating similar physical mechanisms during rupture nucleation. Our data show that accelerated fault creep causes reduction of seismic velocity and elastic moduli during the preparatory phase preceding failure, which suggests that real time monitoring of active faults may be a means to detect earthquake precursors. PMID:27597879

Is There Evidence of Failing to Fail in Our Schools of Nursing?

PubMed

Docherty, Angie; Dieckmann, Nathan

2015-01-01

To assess evidence for "failing to fail" in undergraduate nursing programs. Literature on grading practices largely focuses on clinical or academic grading. Reviewing both as distinct entities may miss a more systemic grading problem. A cross-sectional survey targeted 235 faculty within university and community colleges in a western state. Chi-square tests of independence explored the relation between institutional and faculty variables. The response rate was 34 percent. Results suggest failing to fail may be evident across the sector in both clinical and academic settings: 43 percent of respondents had awarded higher grades than merited; 17.7 percent had passed written examinations they felt should fail; 66 percent believed they had worked with students who should not have passed their previous placement. Failing to fail cuts across instructional settings. Further exploration is imperative if schools are to better engender a climate for rigorously measuring student attainment.

A New Remote Communications Link to Reduce Residential PV Solar Costs

DOE Office of Scientific and Technical Information (OSTI.GOV)

King, Randy; Sugiyama, Rod

Monitoring of PV/DER site production is expensive to install and unreliable. Among third party systems providers, lost communications links are a growing concern. Nearly 20% of links are failing, provisioning is complex, recovery is expensive, production data is lost, and access is fragmented. FleetLink is a new concept in DER system communications, purpose built for lowering the cost of maintaining active contact with residential end user sites and ensuring that production data is reliably available to third party systems providers. Systems providers require accurate, secure system monitoring and reporting of production data and system faults while driving down overall costsmore » to compete effectively. This plug and play, independently operating communications solution lowers the cost of fleet contact from typically .08 dollars-$.12/W down to .02 dollars -.03/W including installation and maintenance expenses. FleetLink establishes a breakthrough in simplicity that facilitates rapid expansion of residential solar by reducing initial capital outlay and lowering installation labor time and skill levels. The solution also facilitates higher DER installation growth rates by driving down maintenance costs and eliminating communications trouble calls. This is accomplished by the FleetLink’s unique network technology that enables dynamic network configuration for fast changes, and active, self-healing DER site contact for uptime assurance. Using an open source network framework with proprietary, application specific enhancements, FleetLink independently manages connectivity, security, recovery, grid control communications, and fleet expansion while presenting a compliant SunSpec interface to the third party operations centers. The net system cost savings of at least .05 dollars/W supports the SunShot cost goals and the flexibility and scalability of the solution accelerates the velocity and ubiquitous adoption of solar.« less

Fail-safe designs for large capacity battery systems

DOEpatents

Kim, Gi-Heon; Smith, Kandler; Ireland, John; Pesaran, Ahmad A.; Neubauer, Jeremy

2016-05-17

Fail-safe systems and design methodologies for large capacity battery systems are disclosed. The disclosed systems and methodologies serve to locate a faulty cell in a large capacity battery, such as a cell having an internal short circuit, determine whether the fault is evolving, and electrically isolate the faulty cell from the rest of the battery, preventing further electrical energy from feeding into the fault.

Hybrid Automated Diagnosis of Discrete/Continuous Systems

NASA Technical Reports Server (NTRS)

Park, Han; James, Mark; MacKey, Ryan; Cannon, Howard; Bajwa, Anapa; Maul, William

2007-01-01

A recently conceived method of automated diagnosis of a complex electromechanical system affords a complete set of capabilities for hybrid diagnosis in the case in which the state of the electromechanical system is characterized by both continuous and discrete values (as represented by analog and digital signals, respectively). The method is an integration of two complementary diagnostic systems: (1) beacon-based exception analysis for multi-missions (BEAM), which is primarily useful in the continuous domain and easily performs diagnoses in the presence of transients; and (2) Livingstone, which is primarily useful in the discrete domain and is typically restricted to quasi-steady conditions. BEAM has been described in several prior NASA Tech Briefs articles: "Software for Autonomous Diagnosis of Complex Systems" (NPO-20803), Vol. 26, No. 3 (March 2002), page 33; "Beacon-Based Exception Analysis for Multimissions" (NPO-20827), Vol. 26, No. 9 (September 2002), page 32; "Wavelet-Based Real-Time Diagnosis of Complex Systems" (NPO-20830), Vol. 27, No. 1 (January 2003), page 67; and "Integrated Formulation of Beacon-Based Exception Analysis for Multimissions" (NPO-21126), Vol. 27, No. 3 (March 2003), page 74. Briefly, BEAM is a complete data-analysis method, implemented in software, for real-time or off-line detection and characterization of faults. The basic premise of BEAM is to characterize a system from all available observations and train the characterization with respect to normal phases of operation. The observations are primarily continuous in nature. BEAM isolates anomalies by analyzing the deviations from nominal for each phase of operation. Livingstone is a model-based reasoner that uses a model of a system, controller commands, and sensor observations to track the system s state, and detect and diagnose faults. Livingstone models a system within the discrete domain. Therefore, continuous sensor readings, as well as time, must be discretized. To reason about continuous systems, Livingstone uses monitors that discretize the sensor readings using trending and thresholding techniques. In development of the a hybrid method, BEAM results were sent to Livingstone to serve as an independent source of evidence that is in addition to the evidence gathered by Livingstone standard monitors. The figure depicts the flow of data in an early version of a hybrid system dedicated to diagnosing a simulated electromechanical system. In effect, BEAM served as a "smart" monitor for Livingstone. BEAM read the simulation data, processed the data to form observations, and stored the observations in a file. A monitor stub synchronized the events recorded by BEAM with the output of the Livingstone standard monitors according to time tags. This information was fed to a real-time interface, which buffered and fed the information to Livingstone, and requested diagnoses at the appropriate times. In a test, the hybrid system was found to correctly identify a failed component in an electromechanical system for which neither BEAM nor Livingstone alone yielded the correct diagnosis.

Enhancement of regional wet deposition estimates based on modeled precipitation inputs

Treesearch

James A. Lynch; Jeffery W. Grimm; Edward S. Corbett

1996-01-01

Application of a variety of two-dimensional interpolation algorithms to precipitation chemistry data gathered at scattered monitoring sites for the purpose of estimating precipitation- born ionic inputs for specific points or regions have failed to produce accurate estimates. The accuracy of these estimates is particularly poor in areas of high topographic relief....

In Situ Monitoring of Local Seismicity

DTIC Science & Technology

2000-09-01

91TL�DGMz9?TLq�.1^VDG>’_\\9` . Report Documentation Page Form ApprovedOMB No . 0704-0188 Public reporting burden for the collection of information...of law, no person shall be subject to a penalty for failing to comply with a collection of information if it does not display a currently valid OMB

40 CFR 63.788 - Recordkeeping and reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

... containers meet the standards as described in § 63.783(b)(2); and (vii) The results of any Method 24 of appendix A to 40 CFR part 60 or approved VOHAP measurement test conducted on individual containers of... summary of the number and total duration of incidents that the monitoring protocol failed to perform in...

Comparison of Highly Resolved Model-Based Exposure Metrics for Traffic-Related Air Pollutants to Support Environmental Health Studies

EPA Science Inventory

Human exposure to air pollution in many studies is represented by ambient concentrations from space-time kriging of observed values. Space-time kriging techniques based on a limited number of ambient monitors may fail to capture the concentration from local sources. Further, beca...

Measuring and Monitoring in the South African "Kha Ri Gude" Mass Literacy Campaign

ERIC Educational Resources Information Center

McKay, Veronica

2015-01-01

After many previous failed attempts to reach illiterate adults, the award-winning South African "Kha Ri Gude" mass literacy campaign, launched in 2008, undertook to ensure that learners seized the opportunity to learn--for many adults, this was a "last chance". Written from an insider perspective by the campaign's founding…

Automated monitoring compared to standard care for the early detection of sepsis in critically ill patients.

PubMed

Warttig, Sheryl; Alderson, Phil; Evans, David Jw; Lewis, Sharon R; Kourbeti, Irene S; Smith, Andrew F

2018-06-25

Sepsis is a life-threatening condition that is usually diagnosed when a patient has a suspected or documented infection, and meets two or more criteria for systemic inflammatory response syndrome (SIRS). The incidence of sepsis is higher among people admitted to critical care settings such as the intensive care unit (ICU) than among people in other settings. If left untreated sepsis can quickly worsen; severe sepsis has a mortality rate of 40% or higher, depending on definition. Recognition of sepsis can be challenging as it usually requires patient data to be combined from multiple unconnected sources, and interpreted correctly, which can be complex and time consuming to do. Electronic systems that are designed to connect information sources together, and automatically collate, analyse, and continuously monitor the information, as well as alerting healthcare staff when pre-determined diagnostic thresholds are met, may offer benefits by facilitating earlier recognition of sepsis and faster initiation of treatment, such as antimicrobial therapy, fluid resuscitation, inotropes, and vasopressors if appropriate. However, there is the possibility that electronic, automated systems do not offer benefits, or even cause harm. This might happen if the systems are unable to correctly detect sepsis (meaning that treatment is not started when it should be, or it is started when it shouldn't be), or healthcare staff may not respond to alerts quickly enough, or get 'alarm fatigue' especially if the alarms go off frequently or give too many false alarms. To evaluate whether automated systems for the early detection of sepsis can reduce the time to appropriate treatment (such as initiation of antibiotics, fluids, inotropes, and vasopressors) and improve clinical outcomes in critically ill patients in the ICU. We searched CENTRAL; MEDLINE; Embase; CINAHL; ISI Web of science; and LILACS, clinicaltrials.gov, and the World Health Organization trials portal. We searched all databases from their date of inception to 18 September 2017, with no restriction on country or language of publication. We included randomized controlled trials (RCTs) that compared automated sepsis-monitoring systems to standard care (such as paper-based systems) in participants of any age admitted to intensive or critical care units for critical illness. We defined an automated system as any process capable of screening patient records or data (one or more systems) automatically at intervals for markers or characteristics that are indicative of sepsis. We defined critical illness as including, but not limited to postsurgery, trauma, stroke, myocardial infarction, arrhythmia, burns, and hypovolaemic or haemorrhagic shock. We excluded non-randomized studies, quasi-randomized studies, and cross-over studies . We also excluded studies including people already diagnosed with sepsis. We used the standard methodological procedures expected by Cochrane. Our primary outcomes were: time to initiation of antimicrobial therapy; time to initiation of fluid resuscitation; and 30-day mortality. Secondary outcomes included: length of stay in ICU; failed detection of sepsis; and quality of life. We used GRADE to assess the quality of evidence for each outcome. We included three RCTs in this review. It was unclear if the RCTs were three separate studies involving 1199 participants in total, or if they were reports from the same study involving fewer participants. We decided to treat the studies separately, as we were unable to make contact with the study authors to clarify.All three RCTs are of very low study quality because of issues with unclear randomization methods, allocation concealment and uncertainty of effect size. Some of the studies were reported as abstracts only and contained limited data, which prevented meaningful analysis and assessment of potential biases.The studies included participants who all received automated electronic monitoring during their hospital stay. Participants were randomized to an intervention group (automated alerts sent from the system) or to usual care (no automated alerts sent from the system).Evidence from all three studies reported 'Time to initiation of antimicrobial therapy'. We were unable to pool the data, but the largest study involving 680 participants reported median time to initiation of antimicrobial therapy in the intervention group of 5.6 hours (interquartile range (IQR) 2.3 to 19.7) in the intervention group (n = not stated) and 7.8 hours (IQR 2.5 to 33.1) in the control group (n = not stated).No studies reported 'Time to initiation of fluid resuscitation' or the adverse event 'Mortality at 30 days'. However very low-quality evidence was available where mortality was reported at other time points. One study involving 77 participants reported 14-day mortality of 20% in the intervention group and 21% in the control group (numerator and denominator not stated). One study involving 442 participants reported mortality at 28 days, or discharge was 14% in the intervention group and 10% in the control group (numerator and denominator not reported). Sample sizes were not reported adequately for these outcomes and so we could not estimate confidence intervals.Very low-quality evidence from one study involving 442 participants reported 'Length of stay in ICU'. Median length of stay was 3.0 days in the intervention group (IQR = 2.0 to 5.0), and 3.0 days (IQR 2.0 to 4.0 in the control).Very low-quality evidence from one study involving at least 442 participants reported the adverse effect 'Failed detection of sepsis'. Data were only reported for failed detection of sepsis in two participants and it wasn't clear which group(s) this outcome occurred in.No studies reported 'Quality of life'. It is unclear what effect automated systems for monitoring sepsis have on any of the outcomes included in this review. Very low-quality evidence is only available on automated alerts, which is only one component of automated monitoring systems. It is uncertain whether such systems can replace regular, careful review of the patient's condition by experienced healthcare staff.

Study of Disseminating Landslide Early Warning Information in Malaysia

NASA Astrophysics Data System (ADS)

Koay, Swee Peng; Lateh, Habibah; Tien Tay, Lea; Ahamd, Jamilah; Chan, Huah Yong; Sakai, Naoki; Jamaludin, Suhaimi

2015-04-01

In Malaysia, rain induced landslides are occurring more often than before. The Malaysian Government allocates millions of Malaysian Ringgit for slope monitoring and slope failure remedial measures in the budget every year. In rural areas, local authorities also play a major role in monitoring the slope to prevent casualty by giving information to the residents who are staying near to the slopes. However, there are thousands of slopes which are classified as high risk slopes in Malaysia. Implementing site monitoring system in these slopes to monitor the movement of the soil in the slopes, predicting the occurrence of slopes failure and establishing early warning system are too costly and almost impossible. In our study, we propose Accumulated Rainfall vs. Rainfall Intensity prediction method to predict the slope failure by referring to the predicted rainfall data from radar and the rain volume from rain gauges. The critical line which determines if the slope is in danger, is generated by simulator with well-surveyed the soil property in the slope and compared with historical data. By establishing such predicting system, the slope failure warning information can be obtained and disseminated to the surroundings via SMS, internet and siren. However, establishing the early warning dissemination system is not enough in disaster prevention, educating school children and the community by giving knowledge on landslides, such as landslide's definition, how and why does the slope failure happen and when will it fail, to raise the risk awareness on landslides will reduce landslides casualty, especially in rural area. Moreover, showing video on the risk and symptom of landslides in school will also help the school children gaining the knowledge of landslides. Generating hazard map and landslides historical data provides further information on the occurrence of the slope failure. In future, further study on fine tuning of landslides prediction method, applying IT technology to educate school children and disseminate warning information will assist the government authorities to reduce landslide casualty by disseminating prompt slope failure warning and improving the community's awareness of disaster prevention.

Monitoring of hearing and language in primary health care: project pilot.

PubMed

Wagner, Julianne; Bonamigo, Andrea Wander; Oliveira, Fabiana de; Machado, Márcia Salgado

2017-11-01

This article analyzes the feasibility of implementing a program that monitors the hearing and language development in the first year of life. It is a prospective longitudinal study, in which 41 community health workers were invited to monitor, on a monthly basis, by means of a questionnaire validated earlier, the hearing and language of children born in their micro areas of expertise. Thirty-nine community health workers agreed to participate, with only two refusals. Five gave up participating. Twenty-six (66.66%) did not perform monitoring, seven (17.94%) monitored improperly and only six (15.38%) monitored properly. Just one child failed the quiz, who was forwarded to the hospital that conducted the auditory screening for retesting. These professionals' high activity demand was considered the main reason for the difficulties encountered in this project. In addition, there is the difficulty to have contact with the Family Health Strategy teams, as well as the impossibility of permanent face-to-face discussions and the influence of the community health agents' supervisors.

The value of point-of-care CD4+ and laboratory viral load in tailoring antiretroviral therapy monitoring strategies to resource limitations.

PubMed

Hyle, Emily P; Jani, Ilesh V; Rosettie, Katherine L; Wood, Robin; Osher, Benjamin; Resch, Stephen; Pei, Pamela P; Maggiore, Paolo; Freedberg, Kenneth A; Peter, Trevor; Parker, Robert A; Walensky, Rochelle P

2017-09-24

To examine the clinical and economic value of point-of-care CD4 (POC-CD4) or viral load monitoring compared with current practices in Mozambique, a country representative of the diverse resource limitations encountered by HIV treatment programs in sub-Saharan Africa. We use the Cost-Effectiveness of Preventing AIDS Complications-International model to examine the clinical impact, cost (2014 US$), and incremental cost-effectiveness ratio [$/year of life saved (YLS)] of ART monitoring strategies in Mozambique. We compare: monitoring for clinical disease progression [clinical ART monitoring strategy (CLIN)] vs. annual POC-CD4 in rural settings without laboratory services and biannual laboratory CD4 (LAB-CD4), biannual POC-CD4, and annual viral load in urban settings with laboratory services. We examine the impact of a range of values in sensitivity analyses, using Mozambique's 2014 per capita gross domestic product ($620) as a benchmark cost-effectiveness threshold. In rural settings, annual POC-CD4 compared to CLIN improves life expectancy by 2.8 years, reduces time on failed ART by 0.6 years, and yields an incremental cost-effectiveness ratio of $480/YLS. In urban settings, biannual POC-CD4 is more expensive and less effective than viral load. Compared to biannual LAB-CD4, viral load improves life expectancy by 0.6 years, reduces time on failed ART by 1.0 year, and is cost-effective ($440/YLS). In rural settings, annual POC-CD4 improves clinical outcomes and is cost-effective compared to CLIN. In urban settings, viral load has the greatest clinical benefit and is cost-effective compared to biannual POC-CD4 or LAB-CD4. Tailoring ART monitoring strategies to specific settings with different available resources can improve clinical outcomes while remaining economically efficient.

Obsessive-Compulsive Homeland Security: Insights from the Neurobiological Security Motivation System

DTIC Science & Technology

2018-03-01

hypothesized it can be triggered consciously or unconsciously through olfactory cues.15 Woody and Szechtman argue when the SMS malfunctions and fails to shut...being securitized in the first place. Desecuritization is not to be confused with failed securitization, when an argument by an actor fails to...B. Salter, “ When Securitization Fails : The Hard Case of Counter-Terrorism Programs,” in Securitization Theory: How Security Problems Emerge and

Efficacy of time-lapse photography and repeated counts abundance estimation for white-tailed deer populations

USGS Publications Warehouse

Keever, Allison; McGowan, Conor P.; Ditchkoff, Stephen S.; Acker, S.A.; Grand, James B.; Newbolt, Chad H.

2017-01-01

Automated cameras have become increasingly common for monitoring wildlife populations and estimating abundance. Most analytical methods, however, fail to account for incomplete and variable detection probabilities, which biases abundance estimates. Methods which do account for detection have not been thoroughly tested, and those that have been tested were compared to other methods of abundance estimation. The goal of this study was to evaluate the accuracy and effectiveness of the N-mixture method, which explicitly incorporates detection probability, to monitor white-tailed deer (Odocoileus virginianus) by using camera surveys and a known, marked population to collect data and estimate abundance. Motion-triggered camera surveys were conducted at Auburn University’s deer research facility in 2010. Abundance estimates were generated using N-mixture models and compared to the known number of marked deer in the population. We compared abundance estimates generated from a decreasing number of survey days used in analysis and by time periods (DAY, NIGHT, SUNRISE, SUNSET, CREPUSCULAR, ALL TIMES). Accurate abundance estimates were generated using 24 h of data and nighttime only data. Accuracy of abundance estimates increased with increasing number of survey days until day 5, and there was no improvement with additional data. This suggests that, for our system, 5-day camera surveys conducted at night were adequate for abundance estimation and population monitoring. Further, our study demonstrates that camera surveys and N-mixture models may be a highly effective method for estimation and monitoring of ungulate populations.

76 FR 3064 - Travelers Information Stations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-19

... phone numbers when local 911 systems fail, terror threat alert levels, public health warnings ``and all... Alerts, alternate phone numbers when local 911 systems fail, terror threat alert levels, public health..., alternate phone numbers to 911, terror threat alert levels, and public health warnings--do not appear to be...

Exhaust Air Dust Monitoring is Superior to Soiled Bedding Sentinels for the Detection of Pasteurella pneumotropica in Individually Ventilated Cage Systems.

PubMed

Miller, Manuel; Ritter, Brbel; Zorn, Julia; Brielmeier, Markus

2016-11-01

Reliable detection of unwanted organisms is essential for meaningful health monitoring in experimental animal facilities. Currently, most rodents are housed in IVC systems, which prevent the aerogenic transmission of pathogens between cages. Typically soiled-bedding sentinels (SBS) exposed to soiled bedding collected from a population of animals within an IVC rack are tested as representatives, but infectious agents often go undetected due to inefficient transmission. Pasteurellaceae are among the most prevalent bacterial pathogens isolated from experimental mice, and the failure of SBS to detect these bacteria is well established. In this study, we investigated whether analysis of exhaust air dust (EAD) samples by using a sensitive and specific real-time PCR assay is superior to conventional SBS monitoring for the detection of Pasteurella pneumotropica (Pp) infections. In a rack with a known prevalence of Pp-positive mice, weekly EAD sampling was compared with the classic SBS method over 3 mo. In 6 rounds of testing, with a prevalence of 5 infected mice in each of 7 cages in a rack of 63 cages, EAD PCR detected Pp at every weekly time point; SBS failed to detect Pp in all cases. The minimal prevalence of Pp-infected mice required to obtain a reliable positive result by EAD PCR testing was determined to be 1 in 63 cages. Reliable detection of Pp was achieved after only 1 wk of exposure. Analysis of EAD samples by real-time PCR assay provides a sensitive, simple, and reliable approach for Pp identification in laboratory mice.

Exhaust Air Dust Monitoring is Superior to Soiled Bedding Sentinels for the Detection of Pasteurella pneumotropica in Individually Ventilated Cage Systems

PubMed Central

Miller, Manuel; Ritter, Bärbel; Zorn, Julia; Brielmeier, Markus

2016-01-01

Reliable detection of unwanted organisms is essential for meaningful health monitoring in experimental animal facilities. Currently, most rodents are housed in IVC systems, which prevent the aerogenic transmission of pathogens between cages. Typically soiled-bedding sentinels (SBS) exposed to soiled bedding collected from a population of animals within an IVC rack are tested as representatives, but infectious agents often go undetected due to inefficient transmission. Pasteurellaceae are among the most prevalent bacterial pathogens isolated from experimental mice, and the failure of SBS to detect these bacteria is well established. In this study, we investigated whether analysis of exhaust air dust (EAD) samples by using a sensitive and specific real-time PCR assay is superior to conventional SBS monitoring for the detection of Pasteurella pneumotropica (Pp) infections. In a rack with a known prevalence of Pp-positive mice, weekly EAD sampling was compared with the classic SBS method over 3 mo. In 6 rounds of testing, with a prevalence of 5 infected mice in each of 7 cages in a rack of 63 cages, EAD PCR detected Pp at every weekly time point; SBS failed to detect Pp in all cases. The minimal prevalence of Pp-infected mice required to obtain a reliable positive result by EAD PCR testing was determined to be 1 in 63 cages. Reliable detection of Pp was achieved after only 1 wk of exposure. Analysis of EAD samples by real-time PCR assay provides a sensitive, simple, and reliable approach for Pp identification in laboratory mice. PMID:27931316

Online Condition Monitoring of Gripper Cylinder in TBM Based on EMD Method

NASA Astrophysics Data System (ADS)

Li, Lin; Tao, Jian-Feng; Yu, Hai-Dong; Huang, Yi-Xiang; Liu, Cheng-Liang

2017-11-01

The gripper cylinder that provides braced force for Tunnel Boring Machine (TBM) might fail due to severe vibration when the TBM excavates in the tunnel. Early fault diagnosis of the gripper cylinder is important for the safety and efficiency of the whole tunneling project. In this paper, an online condition monitoring system based on the Empirical Mode Decomposition (EMD) method is established for fault diagnosis of the gripper cylinder while TBM is working. Firstly, the lumped mass parameter model of the gripper cylinder is established considering the influence of the variable stiffness at the rock interface, the equivalent stiffness of the oil, the seals, and the copper guide sleeve. The dynamic performance of the gripper cylinder is investigated to provide basis for its health condition evaluation. Then, the EMD method is applied to identify the characteristic frequencies of the gripper cylinder for fault diagnosis and a field test is used to verify the accuracy of the EMD method for detection of the characteristic frequencies. Furthermore, the contact stiffness at the interface between the barrel and the rod is calculated with Hertz theory and the relationship between the natural frequency and the stiffness varying with the health condition of the cylinder is simulated based on the dynamic model. The simulation shows that the characteristic frequencies decrease with the increasing clearance between the barrel and the rod, thus the defects could be indicated by monitoring the natural frequency. Finally, a health condition management system of the gripper cylinder based on the vibration signal and the EMD method is established, which could ensure the safety of TBM.

Detection of Poliovirus Circulation by Environmental Surveillance in the Absence of Clinical Cases in Israel and the Palestinian Authority

PubMed Central

Manor, Y.; Handsher, R.; Halmut, T.; Neuman, M.; Bobrov, A.; Rudich, H.; Vonsover, A.; Shulman, L.; Kew, O.; Mendelson, E.

1999-01-01

The global eradication of poliomyelitis, believed to be achievable around the year 2000, relies on strategies which include high routine immunization coverage and mass vaccination campaigns, along with continuous monitoring of wild-type virus circulation by using the laboratory-based acute flaccid paralysis (AFP) surveillance. Israel and the Palestinian Authority are located in a geographical region in which poliovirus is still endemic but have been free of poliomyelitis since 1988 as a result of intensive immunization programs and mass vaccination campaigns. To monitor the wild-type virus circulation, environmental surveillance of sewage samples collected monthly from 25 to 30 sites across the country was implemented in 1989 and AFP surveillance began in 1994. The sewage samples were processed in the laboratory with a double-selective tissue culture system, which enabled economical processing of large number of samples. Between 1989 and 1997, 2,294 samples were processed, and wild-type poliovirus was isolated from 17 of them in four clusters, termed “silent outbreaks,” in September 1990 (type 3), between May and September 1991 (type 1), between October 1994 and June 1995 (type 1), and in December 1996 (type 1). Fifteen of the 17 positive samples were collected in the Gaza Strip, 1 was collected in the West Bank, and 1 was collected in the Israeli city of Ashdod, located close to the Gaza Strip. The AFP surveillance system failed to detect the circulating wild-type viruses. These findings further emphasize the important role that environmental surveillance can play in monitoring the eradication of polioviruses. PMID:10325305

Monitoring costs in the ICU: a search for a pertinent methodology.

PubMed

Reis Miranda, D; Jegers, M

2012-10-01

Attempts to determine costs in the intensive care unit (ICU) were not successful until now, as they failed to detect differences of costs between patients. The methodology and/or the instruments used might be at the origin of this failure. Based on the results of the European ICUs studies and on the descriptions of the activities of care in the ICU, we gathered and analysed the relevant literature concerning the monitoring of costs in the ICU. The aim was to formulate a methodology, from an economic perspective, in which future research may be framed. A bottom-up microcosting methodology will enable to distinguish costs between patients. The resulting information will at the same time support the decision-making of top management and be ready to include in the financial system of the hospital. Nursing staff explains about 30% of the total costs. This relation remains constant irrespective of the annual nurse/patient ratio. In contrast with other scoring instruments, the nursing activities score (NAS) covers all nursing activities. (1) NAS is to be chosen for quantifying nursing activities; (2) an instrument for measuring the physician's activities is not yet available; (3) because the nursing activities have a large impact on total costs, the standardisation of the processes of care (following the system approach) will contribute to manage costs, making also reproducible the issue of quality of care; (4) the quantification of the nursing activities may be the required (proxy) input for the automated bottom-up monitoring of costs in the ICU. © 2012 The Authors. Acta Anaesthesiologica Scandinavica © 2012 The Acta Anaesthesiologica Scandinavica Foundation.

Universal power transistor base drive control unit

DOEpatents

Gale, Allan R.; Gritter, David J.

1988-01-01

A saturation condition regulator system for a power transistor which achieves the regulation objectives of a Baker clamp but without dumping excess base drive current into the transistor output circuit. The base drive current of the transistor is sensed and used through an active feedback circuit to produce an error signal which modulates the base drive current through a linearly operating FET. The collector base voltage of the power transistor is independently monitored to develop a second error signal which is also used to regulate base drive current. The current-sensitive circuit operates as a limiter. In addition, a fail-safe timing circuit is disclosed which automatically resets to a turn OFF condition in the event the transistor does not turn ON within a predetermined time after the input signal transition.

Universal power transistor base drive control unit

DOEpatents

Gale, A.R.; Gritter, D.J.

1988-06-07

A saturation condition regulator system for a power transistor is disclosed which achieves the regulation objectives of a Baker clamp but without dumping excess base drive current into the transistor output circuit. The base drive current of the transistor is sensed and used through an active feedback circuit to produce an error signal which modulates the base drive current through a linearly operating FET. The collector base voltage of the power transistor is independently monitored to develop a second error signal which is also used to regulate base drive current. The current-sensitive circuit operates as a limiter. In addition, a fail-safe timing circuit is disclosed which automatically resets to a turn OFF condition in the event the transistor does not turn ON within a predetermined time after the input signal transition. 2 figs.

Real-Time Sensor Validation System Developed for Reusable Launch Vehicle Testbed

NASA Technical Reports Server (NTRS)

Jankovsky, Amy L.

1997-01-01

A real-time system for validating sensor health has been developed for the reusable launch vehicle (RLV) program. This system, which is part of the propulsion checkout and control system (PCCS), was designed for use in an integrated propulsion technology demonstrator testbed built by Rockwell International and located at the NASA Marshall Space Flight Center. Work on the sensor health validation system, a result of an industry-NASA partnership, was completed at the NASA Lewis Research Center, then delivered to Marshall for integration and testing. The sensor validation software performs three basic functions: it identifies failed sensors, it provides reconstructed signals for failed sensors, and it identifies off-nominal system transient behavior that cannot be attributed to a failed sensor. The code is initiated by host software before the start of a propulsion system test, and it is called by the host program every control cycle. The output is posted to global memory for use by other PCCS modules. Output includes a list indicating the status of each sensor (i.e., failed, healthy, or reconstructed) and a list of features that are not due to a sensor failure. If a sensor failure is found, the system modifies that sensor's data array by substituting a reconstructed signal, when possible, for use by other PCCS modules.

Strapdown system redundancy management flight demonstration. [vertical takeoff and landing aircraft

NASA Technical Reports Server (NTRS)

1978-01-01

The suitability of strapdown inertial systems in providing highly reliable short-term navigation for vertical take-off and landing (VTOL) aircraft operating in an intra-urban setting under all-weather conditions was assessed. A preliminary design configuration of a skewed sensor inertial reference system employing a redundancy management concept to achieve fail-operational, fail-operational performance, was developed.

Process Time Refinement for Reusable Launch Vehicle Regeneration Modeling

DTIC Science & Technology

2008-03-01

predicted to fail, or have failed. 3) Augmenting existing space systems with redundant or additional capability to enhance space system performance or...Canopies, External Tanks/Pods/Pylon Ejectors , Armament Bay Doors, Missile Launchers, Wing and Fuselage Center Line Racks, Bomb Bay Release...Systems Test 04583 Thrust Maintenance Operation 04584 Silo Door Operation 04650 Initial Build-up-Recovery Vehicle (RV) 147 04610 Nondestructive

Trying, Choice, Social Conformity and Pride?

ERIC Educational Resources Information Center

Annett, Danielle

2017-01-01

Danielle Annett begins this article by saying that, although the "Brown" decision was more than 60 years ago, communities remain largely segregated, prompting the latest in questionable desegregation attempts. Students are not failing within a strong and well-funded system; rather, an inequitably funded system is failing strong students.…

Work Coordination Engine

NASA Technical Reports Server (NTRS)

Zendejas, Silvino; Bui, Tung; Bui, Bach; Malhotra, Shantanu; Chen, Fannie; Kim, Rachel; Allen, Christopher; Luong, Ivy; Chang, George; Sadaqathulla, Syed

2009-01-01

The Work Coordination Engine (WCE) is a Java application integrated into the Service Management Database (SMDB), which coordinates the dispatching and monitoring of a work order system. WCE de-queues work orders from SMDB and orchestrates the dispatching of work to a registered set of software worker applications distributed over a set of local, or remote, heterogeneous computing systems. WCE monitors the execution of work orders once dispatched, and accepts the results of the work order by storing to the SMDB persistent store. The software leverages the use of a relational database, Java Messaging System (JMS), and Web Services using Simple Object Access Protocol (SOAP) technologies to implement an efficient work-order dispatching mechanism capable of coordinating the work of multiple computer servers on various platforms working concurrently on different, or similar, types of data or algorithmic processing. Existing (legacy) applications can be wrapped with a proxy object so that no changes to the application are needed to make them available for integration into the work order system as "workers." WCE automatically reschedules work orders that fail to be executed by one server to a different server if available. From initiation to completion, the system manages the execution state of work orders and workers via a well-defined set of events, states, and actions. It allows for configurable work-order execution timeouts by work-order type. This innovation eliminates a current processing bottleneck by providing a highly scalable, distributed work-order system used to quickly generate products needed by the Deep Space Network (DSN) to support space flight operations. WCE is driven by asynchronous messages delivered via JMS indicating the availability of new work or workers. It runs completely unattended in support of the lights-out operations concept in the DSN.

Does academic assessment system type affect levels of academic stress in medical students? A cross-sectional study from Pakistan.

PubMed

Ali, Madiha; Asim, Hamna; Edhi, Ahmed Iqbal; Hashmi, Muhammad Daniyal; Khan, Muhammad Shahjahan; Naz, Farah; Qaiser, Kanza Noor; Qureshi, Sidra Masud; Zahid, Mohammad Faizan; Jehan, Imtiaz

2015-01-01

Stress among medical students induced by academic pressures is on the rise among the student population in Pakistan and other parts of the world. Our study examined the relationship between two different systems employed to assess academic performance and the levels of stress among students at two different medical schools in Karachi, Pakistan. A sample consisting of 387 medical students enrolled in pre-clinical years was taken from two universities, one employing the semester examination system with grade point average (GPA) scores (a tiered system) and the other employing an annual examination system with only pass/fail grading. A pre-designed, self-administered questionnaire was distributed. Test anxiety levels were assessed by The Westside Test Anxiety Scale (WTAS). Overall stress was evaluated using the Perceived Stress Scale (PSS). There were 82 males and 301 females while four did not respond to the gender question. The mean age of the entire cohort was 19.7 ± 1.0 years. A total of 98 participants were from the pass/fail assessment system while 289 were from the GPA system. There was a higher proportion of females in the GPA system (85% vs. 59%; p < 0.01). Students in the pass/fail assessment system had a lower score on the WTAS (2.4 ± 0.8 vs. 2.8 ± 0.7; p = 0.01) and the PSS (17.0 ± 6.7 vs. 20.3 ± 6.8; p < 0.01), indicating lower levels of test anxiety and overall stress than in students enrolled in the GPA assessment system. More students in the pass/fail system were satisfied with their performance than those in the GPA system. Based on the present study, we suggest governing bodies to revise and employ a uniform assessment system for all the medical colleges to improve student academic performance and at the same time reduce stress levels. Our results indicate that the pass/fail assessment system accomplishes these objectives.

Landfill disposal systems.

PubMed

Slimak, K M

1978-12-01

The current status of landfill disposal of hazardous wastes in the United States is indicated by presenting descriptions of six operating landfills. These landfills illustrate the variety of techniques that exist in landfill disposal of hazardous wastes. Although some landfills more effectively isolate hazardous waste than others, all landfills must deal with the following problems. Leachate from hazardous waste landfills is generally highly polluted. Most landfills attempt to contain leachate at the site and prevent its discharge to surface or groundwaters. To retain leachate within a disposal area, subsurface barriers of materials such as concrete, asphalt, butyl rubber, vinyl, and clay are used. It is difficult to assure that these materials can seal a landfill indefinitely. When a subsurface barrier fails, the leachate enters the groundwater in a concentrated, narrow band which may bypass monitoring wells. Once a subsurface barrier has failed, repairs are time-consuming and costly, since the waste above the repair site may have to be removed. The central problem in landfill disposal is leachate control. Recent emphasis has been on developing subsurface barriers to contain the wastes and any leachate. Future emphasis should also be on techniques for removing water from hazardous wastes before they are placed in landfills, and on methods for preventing contact of the wastes with water during and after disposal operations. When leachate is eliminated, the problems of monitoring, and subsurface barrier failure and repair can be addressed, and a waste can be effectively isolated.A surface seal landfill design is recommended for maintaining the dry state of solid hazardous wastes and for controlling leachate. Any impervious liner is utilized over the top of the landfill to prevent surface water from seeping into the waste. The surface barrier is also the site where monitoring and maintenance activities are focused. Barrier failure can be detected by visual inspections and any repairs can be made without disturbing the waste. The surface seal landfill does not employ a subsurface barrier. The surface seal landfill successfully addresses each of the four environmental problems listed above, provided that this landfill design is utilized for dry wastes only and is located at a site which provides protection from groundwater and temporary perched water tables.

Health management and controls for Earth-to-orbit propulsion systems

NASA Astrophysics Data System (ADS)

Bickford, R. L.

1995-03-01

Avionics and health management technologies increase the safety and reliability while decreasing the overall cost for Earth-to-orbit (ETO) propulsion systems. New ETO propulsion systems will depend on highly reliable fault tolerant flight avionics, advanced sensing systems and artificial intelligence aided software to ensure critical control, safety and maintenance requirements are met in a cost effective manner. Propulsion avionics consist of the engine controller, actuators, sensors, software and ground support elements. In addition to control and safety functions, these elements perform system monitoring for health management. Health management is enhanced by advanced sensing systems and algorithms which provide automated fault detection and enable adaptive control and/or maintenance approaches. Aerojet is developing advanced fault tolerant rocket engine controllers which provide very high levels of reliability. Smart sensors and software systems which significantly enhance fault coverage and enable automated operations are also under development. Smart sensing systems, such as flight capable plume spectrometers, have reached maturity in ground-based applications and are suitable for bridging to flight. Software to detect failed sensors has reached similar maturity. This paper will discuss fault detection and isolation for advanced rocket engine controllers as well as examples of advanced sensing systems and software which significantly improve component failure detection for engine system safety and health management.

Evaluation of Multi-Level Support Structure Requirements for New Weapon Systems.

DTIC Science & Technology

1987-09-01

transformer 1 total consumed manhours on this level 19.45 hrs average manhrs within 4 weeks on this level : .38 hrs average rounded number of mainten; personal ...major unit data to provide conclusions about the logistics behavior of failing weapon systems. The modeling of system behavior with CAESAR has severa-l...characteristic data and major unit data to provide conclusions about the logistics behavior of failing weapon systems. The modelling of system behavior

AAV viral vector delivery to the brain by shape-conforming MR-guided infusions.

PubMed

Bankiewicz, Krystof S; Sudhakar, Vivek; Samaranch, Lluis; San Sebastian, Waldy; Bringas, John; Forsayeth, John

2016-10-28

Gene transfer technology offers great promise as a potential therapeutic approach to the brain but has to be viewed as a very complex technology. Success of ongoing clinical gene therapy trials depends on many factors such as selection of the correct genetic and anatomical target in the brain. In addition, selection of the viral vector capable of transfer of therapeutic gene into target cells, along with long-term expression that avoids immunotoxicity has to be established. As with any drug development strategy, delivery of gene therapy has to be consistent and predictable in each study subject. Failed drug and vector delivery will lead to failed clinical trials. In this article, we describe our experience with AAV viral vector delivery system, that allows us to optimize and monitor in real time viral vector administration into affected regions of the brain. In addition to discussing MRI-guided technology for administration of AAV vectors we have developed and now employ in current clinical trials, we also describe ways in which infusion cannula design and stereotactic trajectory may be used to maximize the anatomical coverage by using fluid backflow. This innovative approach enables more precise coverage by fitting the shape of the infusion to the shape of the anatomical target. Copyright © 2016 Elsevier B.V. All rights reserved.

An explosion of a CNG fuel vessel in an urban bus.

PubMed

Park, Chan-Seong; Jeon, Seung-Won; Moon, Jung-Eun; Lee, Kyu-Jung

2010-03-01

An investigation is presented of the explosion of a CNG (compressed natural gas) fuel vessel, called a liner, in an urban bus. The explosion happened at a gas station 10 min after filling was completed. There were no traces of soot and flames at the failed liner, which would be indicative of explosion by ignition of the gas. The filling process of the station was automatically monitored and recorded in a computer. There was no unusual record of the filling system that indicated excess pressure at the time of the accident. There were cracks on the liner that were initiated at the outer surface of the cylindrical shell located at a point 4 cm above the lower dome where cracks did not originate easily as a result of overload. Chemical analysis was performed on a specimen that was cut from the liner, and there was no peculiarity in the mix. Mechanical analysis was performed on the specimens and showed that the hardness was not in the specified range because of inadequate heat treatment of the metal. The hardness of the liner was strictly controlled in the manufacturing process. All the liners that were manufactured at the same period with the failed liner were recalled for examination.

Performance of particulate containment at nanotechnology workplaces

NASA Astrophysics Data System (ADS)

Lo, Li-Ming; Tsai, Candace S.-J.; Dunn, Kevin H.; Hammond, Duane; Marlow, David; Topmiller, Jennifer; Ellenbecker, Michael

2015-11-01

The evaluation of engineering controls for the production or use of carbon nanotubes (CNTs) was investigated at two facilities. These control assessments are necessary to evaluate the current status of control performance and to develop proper control strategies for these workplaces. The control systems evaluated in these studies included ventilated enclosures, exterior hoods, and exhaust filtration systems. Activity-based monitoring with direct-reading instruments and filter sampling for microscopy analysis were used to evaluate the effectiveness of control measures at study sites. Our study results showed that weighing CNTs inside the biological safety cabinet can have a 37 % reduction on the particle concentration in the worker's breathing zone, and produce a 42 % lower area concentration outside the enclosure. The ventilated enclosures used to reduce fugitive emissions from the production furnaces exhibited good containment characteristics when closed, but they failed to contain emissions effectively when opened during product removal/harvesting. The exhaust filtration systems employed for exhausting these ventilated enclosures did not provide promised collection efficiencies for removing engineered nanomaterials from furnace exhaust. The exterior hoods were found to be a challenge for controlling emissions from machining nanocomposites: the downdraft hood effectively contained and removed particles released from the manual cutting process, but using the canopy hood for powered cutting of nanocomposites created 15-20 % higher ultrafine (<500 nm) particle concentrations at the source and at the worker's breathing zone. The microscopy analysis showed that CNTs can only be found at production sources but not at the worker breathing zones during the tasks monitored.

Cascading Failures in Bi-partite Graphs: Model for Systemic Risk Propagation

PubMed Central

Huang, Xuqing; Vodenska, Irena; Havlin, Shlomo; Stanley, H. Eugene

2013-01-01

As economic entities become increasingly interconnected, a shock in a financial network can provoke significant cascading failures throughout the system. To study the systemic risk of financial systems, we create a bi-partite banking network model composed of banks and bank assets and propose a cascading failure model to describe the risk propagation process during crises. We empirically test the model with 2007 US commercial banks balance sheet data and compare the model prediction of the failed banks with the real failed banks after 2007. We find that our model efficiently identifies a significant portion of the actual failed banks reported by Federal Deposit Insurance Corporation. The results suggest that this model could be useful for systemic risk stress testing for financial systems. The model also identifies that commercial rather than residential real estate assets are major culprits for the failure of over 350 US commercial banks during 2008–2011. PMID:23386974

Successful placement of the Essure device after a failed procedure using the Adiana system for hysteroscopic sterilisation

PubMed Central

Schuurman, Teska; Veersema, Sebastiaan

2011-01-01

This case report describes a successful hysteroscopic sterilisation using the Essure Permanent Birth Control device (Conceptus Inc., Mountain View, California, United States) after a failed procedure of the Adiana Permanent Contraception system (Hologic, Inc., Bedford, Maryland, United States). The delivery catheter of the Adiana system was able to be inserted into the left fallopian tube without difficulty and per manufacturer specifications. However, the position detection array was unable to sense four-quadrant tissue contact. The same issue occurred at the contralateral tube. Using the Essure system, the coils were able to be placed in both ostia easily and adequately. In patients in whom the Adiana system fails to occlude the fallopian tubes due to procedural, anatomic or device-related factors, the Essure procedure may be an efficient alternative. PMID:22689274

Statistical Requirements For Pass-Fail Testing Of Contraband Detection Systems

NASA Astrophysics Data System (ADS)

Gilliam, David M.

2011-06-01

Contraband detection systems for homeland security applications are typically tested for probability of detection (PD) and probability of false alarm (PFA) using pass-fail testing protocols. Test protocols usually require specified values for PD and PFA to be demonstrated at a specified level of statistical confidence CL. Based on a recent more theoretical treatment of this subject [1], this summary reviews the definition of CL and provides formulas and spreadsheet functions for constructing tables of general test requirements and for determining the minimum number of tests required. The formulas and tables in this article may be generally applied to many other applications of pass-fail testing, in addition to testing of contraband detection systems.

Educational Value Units: A Mission-Based Approach to Assigning and Monitoring Faculty Teaching Activities in an Academic Medical Department.

PubMed

Regan, Linda; Jung, Julianna; Kelen, Gabor D

2016-12-01

Increasing emphasis on revenue generation could jeopardize the fundamental notion of what it means to be faculty. Despite being a core mission, education is often marginalized in academic medical departments, and expectations of faculty effort in this area are often vague. A potential solution is mission-based budgeting (MBB), which refers to the allocation of resources based on core-mission-related priorities. From December 2012 to March 2013, the authors developed an educational value unit (EVU) system (using an MBB approach) to assign and monitor teaching activities related to the core departmental educational mission at the Department of Emergency Medicine, Johns Hopkins Medicine. EVUs were based on learner contact time, with one EVU equal to roughly one hour of in-person time with medical students or residents. Core education faculty vetted the proposed system; educational leaders determined the total EVUs needed and assessed the impact of their equitable distribution among faculty; and faculty members selected preferences and were assigned EVU obligations. For academic year 2013-2014, 5,896 EVUs were distributed among 54 faculty. At the end of the year, complete EVU data were available for 47 faculty. Of these, only 6 failed to complete their assigned EVU obligations. All core teaching activities were covered, and educational efforts were distributed more equitably across faculty. The system is being refined, with an emphasis on incorporating learner outcome metrics, refining the teaching grid, incorporating failure to meet EVU obligations into yearly faculty evaluations, and disseminating the system to other departments and institutions.

The Grading Nemesis: An Historical Overview and a Current Look at Pass/Fail Grading.

ERIC Educational Resources Information Center

Weller, L. David

1983-01-01

A brief history of grading practices at American colleges and universities is given, along with results of a survey of the current uses of pass/fail grading. The pass/fail system is widely used for a limited number of elective courses. Its adoption peaked during the mid-1970s. (PP)

A Psychodynamic Systems Perspective on Command Relationship during Combat Operations

DTIC Science & Technology

2017-06-09

that theirs is a high likelihood of conflicts when leaders fail to act as a boundary regulator. Failing to act as a boundary regulator, affects the...healthy command climate based on mission command.2 However, leaders do not always succeed in this task, and when they fail it, can have severe... when a leader fails to fulfill his role as a boundary regulator, there is a marked potential for conflict, as was highlighted with the case where the

The Presence of the Correlates of Effective Schools at the District Level: A Case Study

ERIC Educational Resources Information Center

Thompson, DeNelle

2013-01-01

Although the No Child Left Behind Act (NCLB) requires all American public schools to meet Adequate Yearly Progress (AYP), many fail to meet this standard each year. Effective Schools Research has revealed several correlates, such as a clear mission, a safe climate, strong instructional leadership, monitoring of student progress, strong…

Bullying Prevention for School Safety (with Related Video)

ERIC Educational Resources Information Center

Johnson, Katie

2012-01-01

The nation watched in shock recently as four middle school boys barraged 68-year-old bus monitor Karen Klein with jabs about her weight, attacks on her family, and chuckled as they made violent and graphic threats. Klein remained quiet, taking the abuse and failing to respond to the students. This incident might have gone unnoticed and unreported,…

Preferences and Attitudes toward Progress Reporting Methods of Parents from Diverse Backgrounds

ERIC Educational Resources Information Center

Sousa, Darlene Anastacia; Luze, Gayle; Hughes-Belding, Kere

2014-01-01

There is a growing movement in education toward data-based decision-making requiring frequent monitoring of student progress. However, the literature fails to provide direction as to the best means of communicating information about a child's progress with his or her parents. Given the increasing number of immigrant families being served, it…

49 CFR 384.229 - Skills test examiner auditing and monitoring.

Code of Federal Regulations, 2011 CFR

2011-10-01

... must be performed at least once every year; (c) Establish and maintain a database to track pass/fail... maintain a database of all third party testers and examiners, which at a minimum tracks the dates and... and maintain a database of all State CDL skills examiners, which at a minimum tracks the dates and...

49 CFR 384.229 - Skills test examiner auditing and monitoring.

Code of Federal Regulations, 2012 CFR

2012-10-01

... must be performed at least once every year; (c) Establish and maintain a database to track pass/fail... maintain a database of all third party testers and examiners, which at a minimum tracks the dates and... and maintain a database of all State CDL skills examiners, which at a minimum tracks the dates and...

Land, Atmosphere Near Real-time Capability for EOS (LANCE) AMSR2 Data System

NASA Astrophysics Data System (ADS)

Smith, D. K.; Harrison, S.; Lin, H.; Flynn, S.; Nair, M.; Conover, H.; Graves, S. J.

2016-12-01

The Land, Atmosphere Near real-time Capability for EOS (LANCE) system was initiated to ensure the availability of NASA satellite data products to those partners who have grown to rely upon near real-time (NRT) data for their decision support systems. The LANCE Advanced Microwave Scanning Radiometer-EOS (AMSR-E) system was able to address the needs of the NRT community in areas such as weather prediction and forecasting, monitoring of natural hazards, disaster relief, agriculture, and homeland security for nearly one year before the instrument failed in 2011. The timely launch of Global Change Observation Mission -Water 1 (GCOM-W1) and the AMSR2 instrument by the Japanese Aerospace Exploration Agency (JAXA) in 2012 was very important to continue the time series of AMSR instruments. The LANCE element for AMSR2 was able to leverage the LANCE AMSR-E system architecture, using modified AMSR-E standard product algorithms in order to make preliminary data products available to NRT users before US AMSR2 standard product algorithms were available. This presentation will describe the five AMSR2 NRT product suites available from LANCE - Sea Ice, Snow, Rain/Ocean, and Soil Moisture. We will also discuss future plans for LANCE AMSR2.

Poka Yoke system based on image analysis and object recognition

NASA Astrophysics Data System (ADS)

Belu, N.; Ionescu, L. M.; Misztal, A.; Mazăre, A.

2015-11-01

Poka Yoke is a method of quality management which is related to prevent faults from arising during production processes. It deals with “fail-sating” or “mistake-proofing”. The Poka-yoke concept was generated and developed by Shigeo Shingo for the Toyota Production System. Poka Yoke is used in many fields, especially in monitoring production processes. In many cases, identifying faults in a production process involves a higher cost than necessary cost of disposal. Usually, poke yoke solutions are based on multiple sensors that identify some nonconformities. This means the presence of different equipment (mechanical, electronic) on production line. As a consequence, coupled with the fact that the method itself is an invasive, affecting the production process, would increase its price diagnostics. The bulky machines are the means by which a Poka Yoke system can be implemented become more sophisticated. In this paper we propose a solution for the Poka Yoke system based on image analysis and identification of faults. The solution consists of a module for image acquisition, mid-level processing and an object recognition module using associative memory (Hopfield network type). All are integrated into an embedded system with AD (Analog to Digital) converter and Zync 7000 (22 nm technology).

Organisational reporting and learning systems: Innovating inside and outside of the box.

PubMed

Sujan, Mark; Furniss, Dominic

2015-01-01

Reporting and learning systems are key organisational tools for the management and prevention of clinical risk. However, current approaches, such as incident reporting, are struggling to meet expectations of turning health systems like the UK National Health Service (NHS) into learning organisations. This article aims to open up debate on the potential for novel reporting and learning systems in healthcare, by reflecting on experiences from two recent projects: Proactive Risk Monitoring in Healthcare (PRIMO) and Errordiary in Healthcare. These two approaches demonstrate how paying attention to ordinary, everyday clinical work can derive useful learning and active discussion about clinical risk. We argue that innovations in reporting and learning systems might come from both inside and outside of the box. 'Inside' being along traditional paths of controlled organisational innovation. 'Outside' in the sense that inspiration comes outside of the healthcare domain, or more extremely, outside official channels through external websites and social media (e.g. patient forums, public review sites, whistleblower blogs and Twitter streams). Reporting routes that bypass official channels could empower staff and patient activism, and turn out to be a driver to challenge organisational processes, assumptions and priorities where the organisation is failing and has become unresponsive.

Collaborative Group Learning and Knowledge Building to Address Information Systems Project Failure

ERIC Educational Resources Information Center

Angelo, Raymond

2011-01-01

Approximately half of the information systems (IS) projects implemented each year are considered failures. These failed projects cost billions of dollars annually. Failures can be due to projects being delivered late, over-budget, abandoned after significant time and resource investment, or failing to achieve desired results. More often than not,…

Performance of a fail-safe system to follow up abnormal mammograms in primary care.

PubMed

Grossman, Ellie; Phillips, Russell S; Weingart, Saul N

2010-09-01

Missed and delayed breast cancer diagnoses are major sources of potential harm to patients and medical malpractice liability in the United States. Follow-up of abnormal mammogram results is an essential but challenging component of safe breast care. To explore the value of an inexpensive method to follow up abnormal test results, we examined a paper-based fail-safe system. We examined a fail-safe system used to follow up abnormal mammograms at a primary care practice at an urban teaching hospital. We analyzed all abnormal mammogram reports and clinicians' responses to follow-up reminders. We characterized potential lapses identified in this system and used regression models to identify patient, provider, and test result characteristics associated with such lapses. Clinicians responded to fail-safe reminders for 92% of 948 abnormal mammograms. Clinicians reported that they were unaware of the abnormal result in 8% of cases and that there was no follow-up plan in place for 3% of cases. Clinicians with more years of experience were more likely to be aware of the abnormal result (odds of being unaware per incremental year in practice, 0.92; 95% confidence interval, 0.88-0.97) and were more likely to have a follow-up plan. A paper-based fail-safe system for abnormal mammograms is feasible in a primary care practice. However, special care is warranted to ensure full clinician adherence and address staff transitions and trainee-related issues.

Implementation of a Novel Adherence Monitoring Strategy in a Phase III, Blinded, Placebo-Controlled, HIV-1 Prevention Clinical Trial.

PubMed

Husnik, Marla J; Brown, Elizabeth R; Marzinke, Mark; Livant, Edward; Palanee-Phillips, Thesla; Hendrix, Craig W; Matovu Kiweewa, Flavia; Nair, Gonasagrie; Soto-Torres, Lydia E; Schwartz, Katie; Hillier, Sharon L; Baeten, Jared M

2017-11-01

Placebo-controlled HIV-1 prevention trials of pre-exposure prophylaxis (PrEP) have not generally used concurrent measurement of adherence because of the potential risk of unblinding. However, several pre-exposure prophylaxis trials for HIV-1 prevention among women failed to show effectiveness because of low product adherence. Evaluation of product adherence objectively during a study provides the opportunity for strengthening adherence activities at sites having low adherence. During MTN-020/ASPIRE, a phase III, placebo-controlled trial of the dapivirine intravaginal ring, we implemented an adherence monitoring system. Monitoring began in quarter 1 (Q1) 2013 and continued through the conclusion of the trial. Blood plasma was collected quarterly and tested for dapivirine concentrations while maintaining blinding among study team members involved in participant management. Dapivirine concentrations >95 pg/mL, reflecting >8 hours of continuous use, were assessed as signaling product use. Study leadership monitored results on a monthly basis and provided feedback to site investigators. Experiences were shared across sites to motivate staff and counsel participants to strive toward higher adherence levels. An upward trend in adherence was observed (P < 0.0001); the proportion of samples from subjects in the active arm with dapivirine >95 pg/mL increased from 63% in Q1 2013 to 84% by Q1 2015. Ongoing drug level testing as a marker of adherence in MTN-020/ASPIRE demonstrates the feasibility of real-time adherence monitoring while maintaining study blinding at the level of participants, sites, and study leadership. This approach is novel for large-scale effectiveness studies for HIV-1 prevention.

Design, implementation and multisite evaluation of a system suitability protocol for the quantitative assessment of instrument performance in liquid chromatography-multiple reaction monitoring-MS (LC-MRM-MS).

PubMed

Abbatiello, Susan E; Mani, D R; Schilling, Birgit; Maclean, Brendan; Zimmerman, Lisa J; Feng, Xingdong; Cusack, Michael P; Sedransk, Nell; Hall, Steven C; Addona, Terri; Allen, Simon; Dodder, Nathan G; Ghosh, Mousumi; Held, Jason M; Hedrick, Victoria; Inerowicz, H Dorota; Jackson, Angela; Keshishian, Hasmik; Kim, Jong Won; Lyssand, John S; Riley, C Paige; Rudnick, Paul; Sadowski, Pawel; Shaddox, Kent; Smith, Derek; Tomazela, Daniela; Wahlander, Asa; Waldemarson, Sofia; Whitwell, Corbin A; You, Jinsam; Zhang, Shucha; Kinsinger, Christopher R; Mesri, Mehdi; Rodriguez, Henry; Borchers, Christoph H; Buck, Charles; Fisher, Susan J; Gibson, Bradford W; Liebler, Daniel; Maccoss, Michael; Neubert, Thomas A; Paulovich, Amanda; Regnier, Fred; Skates, Steven J; Tempst, Paul; Wang, Mu; Carr, Steven A

2013-09-01

Multiple reaction monitoring (MRM) mass spectrometry coupled with stable isotope dilution (SID) and liquid chromatography (LC) is increasingly used in biological and clinical studies for precise and reproducible quantification of peptides and proteins in complex sample matrices. Robust LC-SID-MRM-MS-based assays that can be replicated across laboratories and ultimately in clinical laboratory settings require standardized protocols to demonstrate that the analysis platforms are performing adequately. We developed a system suitability protocol (SSP), which employs a predigested mixture of six proteins, to facilitate performance evaluation of LC-SID-MRM-MS instrument platforms, configured with nanoflow-LC systems interfaced to triple quadrupole mass spectrometers. The SSP was designed for use with low multiplex analyses as well as high multiplex approaches when software-driven scheduling of data acquisition is required. Performance was assessed by monitoring of a range of chromatographic and mass spectrometric metrics including peak width, chromatographic resolution, peak capacity, and the variability in peak area and analyte retention time (RT) stability. The SSP, which was evaluated in 11 laboratories on a total of 15 different instruments, enabled early diagnoses of LC and MS anomalies that indicated suboptimal LC-MRM-MS performance. The observed range in variation of each of the metrics scrutinized serves to define the criteria for optimized LC-SID-MRM-MS platforms for routine use, with pass/fail criteria for system suitability performance measures defined as peak area coefficient of variation <0.15, peak width coefficient of variation <0.15, standard deviation of RT <0.15 min (9 s), and the RT drift <0.5min (30 s). The deleterious effect of a marginally performing LC-SID-MRM-MS system on the limit of quantification (LOQ) in targeted quantitative assays illustrates the use and need for a SSP to establish robust and reliable system performance. Use of a SSP helps to ensure that analyte quantification measurements can be replicated with good precision within and across multiple laboratories and should facilitate more widespread use of MRM-MS technology by the basic biomedical and clinical laboratory research communities.

Design, Implementation and Multisite Evaluation of a System Suitability Protocol for the Quantitative Assessment of Instrument Performance in Liquid Chromatography-Multiple Reaction Monitoring-MS (LC-MRM-MS)*

PubMed Central

Abbatiello, Susan E.; Mani, D. R.; Schilling, Birgit; MacLean, Brendan; Zimmerman, Lisa J.; Feng, Xingdong; Cusack, Michael P.; Sedransk, Nell; Hall, Steven C.; Addona, Terri; Allen, Simon; Dodder, Nathan G.; Ghosh, Mousumi; Held, Jason M.; Hedrick, Victoria; Inerowicz, H. Dorota; Jackson, Angela; Keshishian, Hasmik; Kim, Jong Won; Lyssand, John S.; Riley, C. Paige; Rudnick, Paul; Sadowski, Pawel; Shaddox, Kent; Smith, Derek; Tomazela, Daniela; Wahlander, Asa; Waldemarson, Sofia; Whitwell, Corbin A.; You, Jinsam; Zhang, Shucha; Kinsinger, Christopher R.; Mesri, Mehdi; Rodriguez, Henry; Borchers, Christoph H.; Buck, Charles; Fisher, Susan J.; Gibson, Bradford W.; Liebler, Daniel; MacCoss, Michael; Neubert, Thomas A.; Paulovich, Amanda; Regnier, Fred; Skates, Steven J.; Tempst, Paul; Wang, Mu; Carr, Steven A.

2013-01-01

Multiple reaction monitoring (MRM) mass spectrometry coupled with stable isotope dilution (SID) and liquid chromatography (LC) is increasingly used in biological and clinical studies for precise and reproducible quantification of peptides and proteins in complex sample matrices. Robust LC-SID-MRM-MS-based assays that can be replicated across laboratories and ultimately in clinical laboratory settings require standardized protocols to demonstrate that the analysis platforms are performing adequately. We developed a system suitability protocol (SSP), which employs a predigested mixture of six proteins, to facilitate performance evaluation of LC-SID-MRM-MS instrument platforms, configured with nanoflow-LC systems interfaced to triple quadrupole mass spectrometers. The SSP was designed for use with low multiplex analyses as well as high multiplex approaches when software-driven scheduling of data acquisition is required. Performance was assessed by monitoring of a range of chromatographic and mass spectrometric metrics including peak width, chromatographic resolution, peak capacity, and the variability in peak area and analyte retention time (RT) stability. The SSP, which was evaluated in 11 laboratories on a total of 15 different instruments, enabled early diagnoses of LC and MS anomalies that indicated suboptimal LC-MRM-MS performance. The observed range in variation of each of the metrics scrutinized serves to define the criteria for optimized LC-SID-MRM-MS platforms for routine use, with pass/fail criteria for system suitability performance measures defined as peak area coefficient of variation <0.15, peak width coefficient of variation <0.15, standard deviation of RT <0.15 min (9 s), and the RT drift <0.5min (30 s). The deleterious effect of a marginally performing LC-SID-MRM-MS system on the limit of quantification (LOQ) in targeted quantitative assays illustrates the use and need for a SSP to establish robust and reliable system performance. Use of a SSP helps to ensure that analyte quantification measurements can be replicated with good precision within and across multiple laboratories and should facilitate more widespread use of MRM-MS technology by the basic biomedical and clinical laboratory research communities. PMID:23689285

Hybrid composite rebars for smart concrete structures

NASA Astrophysics Data System (ADS)

Krishnamoorthy, R. K.; Belarbi, Abdeldjelil; Chandrashekhara, K.; Watkins, Steve E.

1997-05-01

In reinforced concrete structures, steel reinforcing bars (rebars) corrode with time and thus reduce their life span. Composite rebars can be used in lieu of steel rebars to overcome this problem. The conventional composite rebars designed to take tensile force are composed of unidirectional fibers in a resin matrix, and are linearly elastic till failure; thus providing a brittle behavior. The problems of corrosion and brittle behavior can be solved by using a composite rebar which fails gradually under tension. The rebar consists of a hybrid composite system in conjunction with helical fibers. The hybrid system gives the rebar its initial stiffness and enables pseudo-yielding at lower strains. As the strain increase, the load is gradually transferred from the hybrid core to the helical fibers, which enables the rebar to undergo large elongations before failure. Embedded fiber optic sensors in the rebar can be used for health monitoring over a long period of time. The proof of concept and preliminary test results are described in the paper.

Just tell me what you want!: the promise and perils of rapid prototyping with the World Wide Web.

PubMed

Cimino, J J; Socratous, S A

1996-01-01

Construction of applications using the World Wide Web architecture and Hypertext Markup Language (HTML) documents is relatively simple. We are exploring this approach with an application, called PolyMed now in use by surgical residents for one year. We monitored use and obtained user feedback to develop new features and eliminate undesirable ones. The system has been used to keep track of over 4,200 patients. We predicted, several advantages and disadvantages to this approach to prototyping clinical applications. Our experience confirms some advantages (ease of development and customization, ability to exploit non-Web system components, and simplified user interface design) and disadvantages (lack of database management services). Some predicted disadvantages failed to materialize (difficulty modeling a clinical application with hypertext and inconveniences associated with the "connectionless" nature of the Web). We were disappointed to find that while integration of external Web applications (such as Medline) into our application was easy, our users did not find it useful.

Computer Reconstruction of Plant Growth and Chlorophyll Fluorescence Emission in Three Spatial Dimensions

PubMed Central

Bellasio, Chandra; Olejníčková, Julie; Tesař, Radek; Šebela, David; Nedbal, Ladislav

2012-01-01

Plant leaves grow and change their orientation as well their emission of chlorophyll fluorescence in time. All these dynamic plant properties can be semi-automatically monitored by a 3D imaging system that generates plant models by the method of coded light illumination, fluorescence imaging and computer 3D reconstruction. Here, we describe the essentials of the method, as well as the system hardware. We show that the technique can reconstruct, with a high fidelity, the leaf size, the leaf angle and the plant height. The method fails with wilted plants when leaves overlap obscuring their true area. This effect, naturally, also interferes when the method is applied to measure plant growth under water stress. The method is, however, very potent in capturing the plant dynamics under mild stress and without stress. The 3D reconstruction is also highly effective in correcting geometrical factors that distort measurements of chlorophyll fluorescence emission of naturally positioned plant leaves. PMID:22368511

Just tell me what you want!: the promise and perils of rapid prototyping with the World Wide Web.

PubMed Central

Cimino, J. J.; Socratous, S. A.

1996-01-01

Construction of applications using the World Wide Web architecture and Hypertext Markup Language (HTML) documents is relatively simple. We are exploring this approach with an application, called PolyMed now in use by surgical residents for one year. We monitored use and obtained user feedback to develop new features and eliminate undesirable ones. The system has been used to keep track of over 4,200 patients. We predicted, several advantages and disadvantages to this approach to prototyping clinical applications. Our experience confirms some advantages (ease of development and customization, ability to exploit non-Web system components, and simplified user interface design) and disadvantages (lack of database management services). Some predicted disadvantages failed to materialize (difficulty modeling a clinical application with hypertext and inconveniences associated with the "connectionless" nature of the Web). We were disappointed to find that while integration of external Web applications (such as Medline) into our application was easy, our users did not find it useful. PMID:8947759

Computer reconstruction of plant growth and chlorophyll fluorescence emission in three spatial dimensions.

PubMed

Bellasio, Chandra; Olejníčková, Julie; Tesař, Radek; Sebela, David; Nedbal, Ladislav

2012-01-01

Plant leaves grow and change their orientation as well their emission of chlorophyll fluorescence in time. All these dynamic plant properties can be semi-automatically monitored by a 3D imaging system that generates plant models by the method of coded light illumination, fluorescence imaging and computer 3D reconstruction. Here, we describe the essentials of the method, as well as the system hardware. We show that the technique can reconstruct, with a high fidelity, the leaf size, the leaf angle and the plant height. The method fails with wilted plants when leaves overlap obscuring their true area. This effect, naturally, also interferes when the method is applied to measure plant growth under water stress. The method is, however, very potent in capturing the plant dynamics under mild stress and without stress. The 3D reconstruction is also highly effective in correcting geometrical factors that distort measurements of chlorophyll fluorescence emission of naturally positioned plant leaves.

Operating Experience and Reliability Improvements on the 5 kW CW Klystron at Jefferson Lab

NASA Astrophysics Data System (ADS)

Nelson, R.; Holben, S.

1997-05-01

With substantial operating hours on the RF system, considerable information on reliability of the 5 kW CW klystrons has been obtained. High early failure rates led to examination of the operating conditions and failure modes. Internal ceramic contamination caused premature failure of gun potting material and ultimate tube demise through arcing or ceramic fracture. A planned course of repotting and reconditioning of approximately 300 klystrons, plus careful attention to operating conditions and periodic analysis of operational data, has substantially reduced the failure rate. It is anticipated that implementation of planned supplemental monitoring systems for the klystrons will allow most catastrophic failures to be avoided. By predicting end of life, tubes can be changed out before they fail, thus minimizing unplanned downtime. Initial tests have also been conducted on this same klystron operated at higher voltages with resultant higher output power. The outcome of these tests will provide information to be considered for future upgrades to the accelerator.

Around Marshall

NASA Image and Video Library

1983-08-10

One of the main components of the Hubble Space Telescope (HST) is the Solar Array Drive Electronics (SADE) system. This system interfaces with the Support System Module (SSM) for exchange of operational commands and telemetry data. SADE operates and controls the Solar Array Drive Mechanisms (SADM) for the orientation of the Solar Array Drive (SAD). It also monitors the position of the arrays and the temperature of the SADM. During the first HST servicing mission, the astronauts replaced the SADE component because of some malfunctions. This turned out to be a very challenging extravehicular activity (EVA). Two transistors and two diodes had been thermally stressed with the conformal coating discolored and charred. Soldered cornections became molten and reflowed between the two diodes. The failed transistors gave no indication of defective construction. All repairs were made and the HST was redeposited into orbit. Prior to undertaking this challenging mission, the orbiter's crew trained at Marshall Space Flight Center's (MSFC) Neutral Buoyancy Simulator (NBS) to prepare themselves for working in a low gravity environment. They also practiced replacing HST parts and exercised maneuverability and equipment handling. Pictured are crew members practicing on a space platform.

Software Assists in Responding to Anomalous Conditions

NASA Technical Reports Server (NTRS)

James, Mark; Kronbert, F.; Weiner, A.; Morgan, T.; Stroozas, B.; Girouard, F.; Hopkins, A.; Wong, L.; Kneubuhl, J.; Malina, R.

2004-01-01

Fault Induced Document Retrieval Officer (FIDO) is a computer program that reduces the need for a large and costly team of engineers and/or technicians to monitor the state of a spacecraft and associated ground systems and respond to anomalies. FIDO includes artificial-intelligence components that imitate the reasoning of human experts with reference to a knowledge base of rules that represent failure modes and to a database of engineering documentation. These components act together to give an unskilled operator instantaneous expert assistance and access to information that can enable resolution of most anomalies, without the need for highly paid experts. FIDO provides a system state summary (a configurable engineering summary) and documentation for diagnosis of a potentially failing component that might have caused a given error message or anomaly. FIDO also enables high-level browsing of documentation by use of an interface indexed to the particular error message. The collection of available documents includes information on operations and associated procedures, engineering problem reports, documentation of components, and engineering drawings. FIDO also affords a capability for combining information on the state of ground systems with detailed, hierarchically-organized, hypertext- enabled documentation.

Stochastic modeling to identify requirements for centralized monitoring of distributed wastewater treatment.

PubMed

Hug, T; Maurer, M

2012-01-01

Distributed (decentralized) wastewater treatment can, in many situations, be a valuable alternative to a centralized sewer network and wastewater treatment plant. However, it is critical for its acceptance whether the same overall treatment performance can be achieved without on-site staff, and whether its performance can be measured. In this paper we argue and illustrate that the system performance depends not only on the design performance and reliability of the individual treatment units, but also significantly on the monitoring scheme, i.e. on the reliability of the process information. For this purpose, we present a simple model of a fleet of identical treatment units. Thereby, their performance depends on four stochastic variables: the reliability of the treatment unit, the respond time for the repair of failed units, the reliability of on-line sensors, and the frequency of routine inspections. The simulated scenarios show a significant difference between the true performance and the observations by the sensors and inspections. The results also illustrate the trade-off between investing in reactor and sensor technology and in human interventions in order to achieve a certain target performance. Modeling can quantify such effects and thereby support the identification of requirements for the centralized monitoring of distributed treatment units. The model approach is generic and can be extended and applied to various distributed wastewater treatment technologies and contexts.

How health systems could avert 'triple fail' events that are harmful, are costly, and result in poor patient satisfaction.

PubMed

Lewis, Geraint; Kirkham, Heather; Duncan, Ian; Vaithianathan, Rhema

2013-04-01

Health care systems in many countries are using the "Triple Aim"--to improve patients' experience of care, to advance population health, and to lower per capita costs--as a focus for improving quality. Population strategies for addressing the Triple Aim are becoming increasingly prevalent in developed countries, but ultimately success will also require targeting specific subgroups and individuals. Certain events, which we call "Triple Fail" events, constitute a simultaneous failure to meet all three Triple Aim goals. The risk of experiencing different Triple Fail events varies widely across people. We argue that by stratifying populations according to each person's risk and anticipated response to an intervention, health systems could more effectively target different preventive interventions at particular risk strata. In this article we describe how such an approach could be planned and operationalized. Policy makers should consider using this stratified approach to reduce the incidence of Triple Fail events, thereby improving outcomes, enhancing patient experience, and lowering costs.

Identifying Effective and Sustainable Measures for Community-Based Environmental Monitoring

NASA Astrophysics Data System (ADS)

McKay, Ariana J.; Johnson, Chris J.

2017-09-01

Resource development projects typically result in monitoring programs that fail to fully consider the values and participation of surrounding communities. Also, monitoring protocols for single environmental values can be insufficient for addressing the cumulative impacts of resource development. Community-based environmental monitoring (CBEM) has emerged as a way to meaningfully include local citizens in the decision-making process and assessment of the development of natural resources. Our research explored how to develop effective and sustainable CBEM. Interviews were conducted with staff from 15 CBEM programs established across Canada to identify criteria of what constitutes effective CBEM. Results demonstrate that CBEM offers an effective, locally adapted, and culturally applicable approach to facilitate community participation in natural resource management and to track environmental change. Benefits of CBEM include: locally relevant monitoring protocols, inclusion of cumulative impacts, better informed decision-making, and increased awareness and collaboration amongst community, governments, and proponents. Challenges associated with CBEM are cost, capacity, longevity, distribution of results, and establishing credibility. This research validates the use of CBEM for improving resource management.

Science deficiency in conservation practice: the monitoring of tiger populations in India

USGS Publications Warehouse

Karanth, K.U.; Nichols, J.D.; Seidensticker, J.; Dinerstein, Eric; Smith, J.L.D.; McDougal, C.; Johnsingh, A.J.T.; Chundawat, Raghunandan S.; Thapar, V.

2003-01-01

Conservation practices are supposed to get refined by advancing scientific knowledge. We study this phenomenon in the context of monitoring tiger populations in India, by evaluating the 'pugmark census method' employed by wildlife managers for three decades. We use an analytical framework of modem animal population sampling to test the efficacy of the pugmark censuses using scientific data on tigers and our field observations. We identify three critical goals for monitoring tiger populations, in order of increasing sophistication: (1) distribution mapping, (2) tracking relative abundance, (3) estimation of absolute abundance. We demonstrate that the present census-based paradigm does not work because it ignores the first two simpler goals, and targets, but fails to achieve, the most difficult third goal. We point out the utility and ready availability of alternative monitoring paradigms that deal with the central problems of spatial sampling and observability. We propose an alternative sampling-based approach that can be tailored to meet practical needs of tiger monitoring at different levels of refinement.

Why evolutionary biologists should get seriously involved in ecological monitoring and applied biodiversity assessment programs

PubMed Central

Brodersen, Jakob; Seehausen, Ole

2014-01-01

While ecological monitoring and biodiversity assessment programs are widely implemented and relatively well developed to survey and monitor the structure and dynamics of populations and communities in many ecosystems, quantitative assessment and monitoring of genetic and phenotypic diversity that is important to understand evolutionary dynamics is only rarely integrated. As a consequence, monitoring programs often fail to detect changes in these key components of biodiversity until after major loss of diversity has occurred. The extensive efforts in ecological monitoring have generated large data sets of unique value to macro-scale and long-term ecological research, but the insights gained from such data sets could be multiplied by the inclusion of evolutionary biological approaches. We argue that the lack of process-based evolutionary thinking in ecological monitoring means a significant loss of opportunity for research and conservation. Assessment of genetic and phenotypic variation within and between species needs to be fully integrated to safeguard biodiversity and the ecological and evolutionary dynamics in natural ecosystems. We illustrate our case with examples from fishes and conclude with examples of ongoing monitoring programs and provide suggestions on how to improve future quantitative diversity surveys. PMID:25553061

In Search of Black Swans: Identifying Students at Risk of Failing Licensing Examinations.

PubMed

Barber, Cassandra; Hammond, Robert; Gula, Lorne; Tithecott, Gary; Chahine, Saad

2018-03-01

To determine which admissions variables and curricular outcomes are predictive of being at risk of failing the Medical Council of Canada Qualifying Examination Part 1 (MCCQE1), how quickly student risk of failure can be predicted, and to what extent predictive modeling is possible and accurate in estimating future student risk. Data from five graduating cohorts (2011-2015), Schulich School of Medicine & Dentistry, Western University, were collected and analyzed using hierarchical generalized linear models (HGLMs). Area under the receiver operating characteristic curve (AUC) was used to evaluate the accuracy of predictive models and determine whether they could be used to predict future risk, using the 2016 graduating cohort. Four predictive models were developed to predict student risk of failure at admissions, year 1, year 2, and pre-MCCQE1. The HGLM analyses identified gender, MCAT verbal reasoning score, two preclerkship course mean grades, and the year 4 summative objective structured clinical examination score as significant predictors of student risk. The predictive accuracy of the models varied. The pre-MCCQE1 model was the most accurate at predicting a student's risk of failing (AUC 0.66-0.93), while the admissions model was not predictive (AUC 0.25-0.47). Key variables predictive of students at risk were found. The predictive models developed suggest, while it is not possible to identify student risk at admission, we can begin to identify and monitor students within the first year. Using such models, programs may be able to identify and monitor students at risk quantitatively and develop tailored intervention strategies.

DebtRank: Too Central to Fail? Financial Networks, the FED and Systemic Risk

PubMed Central

Battiston, Stefano; Puliga, Michelangelo; Kaushik, Rahul; Tasca, Paolo; Caldarelli, Guido

2012-01-01

Systemic risk, here meant as the risk of default of a large portion of the financial system, depends on the network of financial exposures among institutions. However, there is no widely accepted methodology to determine the systemically important nodes in a network. To fill this gap, we introduce, DebtRank, a novel measure of systemic impact inspired by feedback-centrality. As an application, we analyse a new and unique dataset on the USD 1.2 trillion FED emergency loans program to global financial institutions during 2008–2010. We find that a group of 22 institutions, which received most of the funds, form a strongly connected graph where each of the nodes becomes systemically important at the peak of the crisis. Moreover, a systemic default could have been triggered even by small dispersed shocks. The results suggest that the debate on too-big-to-fail institutions should include the even more serious issue of too-central-to-fail. PMID:22870377

DebtRank: Too Central to Fail? Financial Networks, the FED and Systemic Risk

NASA Astrophysics Data System (ADS)

Battiston, Stefano; Puliga, Michelangelo; Kaushik, Rahul; Tasca, Paolo; Caldarelli, Guido

2012-08-01

Systemic risk, here meant as the risk of default of a large portion of the financial system, depends on the network of financial exposures among institutions. However, there is no widely accepted methodology to determine the systemically important nodes in a network. To fill this gap, we introduce, DebtRank, a novel measure of systemic impact inspired by feedback-centrality. As an application, we analyse a new and unique dataset on the USD 1.2 trillion FED emergency loans program to global financial institutions during 2008-2010. We find that a group of 22 institutions, which received most of the funds, form a strongly connected graph where each of the nodes becomes systemically important at the peak of the crisis. Moreover, a systemic default could have been triggered even by small dispersed shocks. The results suggest that the debate on too-big-to-fail institutions should include the even more serious issue of too-central-to-fail.

DebtRank: too central to fail? Financial networks, the FED and systemic risk.

PubMed

Battiston, Stefano; Puliga, Michelangelo; Kaushik, Rahul; Tasca, Paolo; Caldarelli, Guido

2012-01-01

Systemic risk, here meant as the risk of default of a large portion of the financial system, depends on the network of financial exposures among institutions. However, there is no widely accepted methodology to determine the systemically important nodes in a network. To fill this gap, we introduce, DebtRank, a novel measure of systemic impact inspired by feedback-centrality. As an application, we analyse a new and unique dataset on the USD 1.2 trillion FED emergency loans program to global financial institutions during 2008-2010. We find that a group of 22 institutions, which received most of the funds, form a strongly connected graph where each of the nodes becomes systemically important at the peak of the crisis. Moreover, a systemic default could have been triggered even by small dispersed shocks. The results suggest that the debate on too-big-to-fail institutions should include the even more serious issue of too-central-to-fail.

School Social Workers and a Renewed Call to Advocacy

ERIC Educational Resources Information Center

Joseph, Alfred L., Jr.; Slovak, Karen; Broussard, C. Anne

2010-01-01

This article calls for school social workers to work in schools to reform school systems that have historically failed and are currently failing African American children. While the hope of education is to assist students to realize their potential, school systems across the nation are not reaching this goal. School social work has a duty, a…

An Apparatus for Monitoring the Health of Electrical Cables

NASA Technical Reports Server (NTRS)

Pai, Devdas M.; Tatum, Paul; Pace, Rachel

2004-01-01

As with most elements of infrastructure, electrical wiring is innocuous; usually hidden away and unnoticed until it fails. Failure of infrastructure, however, sometimes leads to serious health and safety hazards. Electrical wiring fails when the polymeric (usually rubber) insulation material that sheathes the conductor gets embrittled with age from exposure to pressure, temperature or radiation cycling or when the insulation gets removed by the chafing of wires against each other. Miles of such wiring can be found in typical aircraft, with significant lengths of the wiring immersed in aviation fuel - a recipe for an explosion if a spark were to occur. Diagnosing the health of wiring is thus an important aspect of monitoring the health of aging aircraft. Stress wave propagation through wiring affords a quick and non-invasive method for health monitoring. The extent to which a stress wave propagating through the cable core gets attenuated depends on the condition of the surrounding insulation. When the insulation is in good condition - supple and pliable, there is more damping or attenuation of the waveform. As the insulation gets embrittled and cracked, the attenuation is likely to reduce and the waveform of the propagating stress wave is likely to change. The monitoring of these changes provides a potential tool to evaluate wiring or cabling in service that is not accessible for visual inspection. This experiment has been designed for use in an introductory mechanical or materials engineering instrumentation lab. Initial setup (after procuring all the materials) should take the lab instructor about 4 hours. A single measurement can be initiated and saved to disk in less than 3 minutes, allowing for all the students in a typical lab section to take their own data rather than share a single set of data for the entire class.

Superiority of automatic remote monitoring compared with in-person evaluation for scheduled ICD follow-up in the TRUST trial - testing execution of the recommendations

PubMed Central

Varma, Niraj; Michalski, Justin; Stambler, Bruce; Pavri, Behzad B.

2014-01-01

Aims To test recommended implantable cardioverter defibrillator (ICD) follow-up methods by ‘in-person evaluations’ (IPE) vs. ‘remote Home Monitoring’ (HM). Methods and results ICD patients were randomized 2:1 to automatic HM or to Conventional monitoring, with follow-up checks scheduled at 3, 6, 9, 12, and 15 months post-implant. Conventional patients were evaluated with IPE only. Home Monitoring patients were assessed remotely only for 1 year between 3 and 15 month evaluations. Adherence to follow-up was measured. HM and Conventional patients were similar (age 63 years, 72% male, left ventricular ejection fraction 29%, primary prevention 73%, DDD 57%). Conventional management suffered greater patient attrition during the trial (20.1 vs. 14.2% in HM, P = 0.007). Three month follow-up occurred in 84% in both groups. There was 100% adherence (5 of 5 checks) in 47.3% Conventional vs. 59.7% HM (P < 0.001). Between 3 and 15 months, HM exhibited superior (2.2×) adherence to scheduled follow-up [incidence of failed follow up was 146 of 2421 (6.0%) in HM vs. 145 of 1098 (13.2%) in Conventional, P < 0.001] and punctuality. In HM (daily transmission success rate median 91%), transmission loss caused only 22 of 2275 (0.97%) failed HM evaluations between 3 and 15 months; others resulted from clinic oversight. Overall IPE failure rate in Conventional [193 of 1841 (10.5%) exceeded that in HM [97 of 1484 (6.5%), P < 0.001] by 62%, i.e. HM patients remained more loyal to IPE when this was mandated. Conclusion Automatic remote monitoring better preserves patient retention and adherence to scheduled follow-up compared with IPE. Clinical trial registration NCT00336284. PMID:24595864

Statistical Requirements For Pass-Fail Testing Of Contraband Detection Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gilliam, David M.

2011-06-01

Contraband detection systems for homeland security applications are typically tested for probability of detection (PD) and probability of false alarm (PFA) using pass-fail testing protocols. Test protocols usually require specified values for PD and PFA to be demonstrated at a specified level of statistical confidence CL. Based on a recent more theoretical treatment of this subject [1], this summary reviews the definition of CL and provides formulas and spreadsheet functions for constructing tables of general test requirements and for determining the minimum number of tests required. The formulas and tables in this article may be generally applied to many othermore » applications of pass-fail testing, in addition to testing of contraband detection systems.« less

Drug Resistance and Viral Tropism in HIV-1 Subtype C-Infected Patients in KwaZulu-Natal, South Africa: Implications for Future Treatment Options

PubMed Central

Singh, Ashika; Sunpath, Henry; Green, Taryn N.; Padayachi, Nagavelli; Hiramen, Keshni; Lie, Yolanda; Anton, Elizabeth D.; Murphy, Richard; Reeves, Jacqueline D.; Kuritzkes, Daniel R.; Ndung’u, Thumbi

2011-01-01

Background Drug resistance poses a significant challenge for the successful application of highly active antiretroviral therapy (HAART) globally. Furthermore, emergence of HIV-1 isolates that preferentially utilize CXCR4 as a coreceptor for cell entry, either as a consequence of natural viral evolution or HAART use may compromise the efficacy of CCR5 antagonists as alternative antiviral therapy. Methods We sequenced the pol gene of viruses from 45 individuals failing at least six months of HAART in Durban, South Africa to determine the prevalence and patterns of drug resistance mutations. Coreceptor usage profiles of these viruses and those from 45 HAART-naive individuals were analyzed using phenotypic and genotypic approaches. Results Ninety-five percent of HAART-failing patients had at least one drug resistance mutation. Thymidine analog mutations (TAMs) were present in 55% of patients with 9% of individuals possessing mutations indicative of the TAM1 pathway, 44% had TAM2 while 7% had mutations common to both pathways. Sixty percent of HAART-failing subjects had X4/dual//mixed-tropic viruses compared to 30% of HAART-naïve subjects (p<0.02). Genetic coreceptor usage prediction algorithms correlated with phenotypic results with 60% of samples from HAART-failing subjects predicted to possess CXCR4-using (X4/dual/mixed viruses) versus 15% of HAART-naïve patients. Conclusions The high proportion of TAMs and X4/dual/mixed HIV-1 viruses among patients failing therapy highlight the need for intensified monitoring of patients taking HAART and the problem of diminished drug options (including CCR5 antagonists) for patients failing therapy in resource-poor settings. PMID:21709569

Cerebral palsy litigation: change course or abandon ship.

PubMed

Sartwelle, Thomas P; Johnston, James C

2015-06-01

The cardinal driver of cerebral palsy litigation is electronic fetal monitoring, which has continued unabated for 40 years. Electronic fetal monitoring, however, is based on 19th-century childbirth myths, a virtually nonexistent scientific foundation, and has a false positive rate exceeding 99%. It has not affected the incidence of cerebral palsy. Electronic fetal monitoring has, however, increased the cesarian section rate, with the expected increase in mortality and morbidity risks to mothers and babies alike. This article explains why electronic fetal monitoring remains endorsed as efficacious in the worlds' labor rooms and courtrooms despite being such a feeble medical modality. It also reviews the reasons professional organizations have failed to condemn the use of electronic fetal monitoring in courtrooms. The failures of tort reform, special cerebral palsy courts, and damage limits to stem the escalating litigation are discussed. Finally, the authors propose using a currently available evidence rule-the Daubert doctrine that excludes "junk science" from the courtroom-as the beginning of the end to cerebral palsy litigation and electronic fetal monitoring's 40-year masquerade as science. © The Author(s) 2014.

Fiber Optic Sensor Embedment Study for Multi-Parameter Strain Sensing

PubMed Central

Drissi-Habti, Monssef; Raman, Venkadesh; Khadour, Aghiad; Timorian, Safiullah

2017-01-01

The fiber optic sensors (FOSs) are commonly used for large-scale structure monitoring systems for their small size, noise free and low electrical risk characteristics. Embedded fiber optic sensors (FOSs) lead to micro-damage in composite structures. This damage generation threshold is based on the coating material of the FOSs and their diameter. In addition, embedded FOSs are aligned parallel to reinforcement fibers to avoid micro-damage creation. This linear positioning of distributed FOS fails to provide all strain parameters. We suggest novel sinusoidal sensor positioning to overcome this issue. This method tends to provide multi-parameter strains in a large surface area. The effectiveness of sinusoidal FOS positioning over linear FOS positioning is studied under both numerical and experimental methods. This study proves the advantages of the sinusoidal positioning method for FOS in composite material’s bonding. PMID:28333117

Continuous positive airway pressure: Physiology and comparison of devices.

PubMed

Gupta, Samir; Donn, Steven M

2016-06-01

Nasal continuous positive airway pressure (CPAP) is increasingly used for respiratory support in preterm babies at birth and after extubation from mechanical ventilation. Various CPAP devices are available for use that can be broadly grouped into continuous flow and variable flow. There are potential physiologic differences between these CPAP systems and the choice of a CPAP device is too often guided by individual expertise and experience rather than by evidence. When interpreting the evidence clinicians should take into account the pressure generation sources, nasal interface, and the factors affecting the delivery of pressure, such as mouth position and respiratory drive. With increasing use of these devices, better monitoring techniques are required to assess the efficacy and early recognition of babies who are failing and in need of escalated support. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fluid Flow Technology that Measures Up

NASA Technical Reports Server (NTRS)

2004-01-01

From 1994 to 1996, NASA s Marshall Space Flight Center conducted a Center Director's Discretionary Fund research effort to apply artificial intelligence technologies to the health management of plant equipment and space propulsion systems. Through this effort, NASA established a business relationship with Quality Monitoring and Control (QMC), of Kingwood, Texas, to provide hardware modeling and artificial intelligence tools. Very detailed and accurate Space Shuttle Main Engine (SSME) analysis and algorithms were jointly created, which identified several missing, critical instrumentation needs for adequately evaluating the engine health status. One of the missing instruments was a liquid oxygen (LOX) flow measurement. This instrument was missing since the original SSME included a LOX turbine flow meter that failed during a ground test, resulting in considerable damage for NASA. New balanced flow meter technology addresses this need with robust, safe, and accurate flow metering hardware.

Integrated Software Health Management for Aircraft GN and C

NASA Technical Reports Server (NTRS)

Schumann, Johann; Mengshoel, Ole

2011-01-01

Modern aircraft rely heavily on dependable operation of many safety-critical software components. Despite careful design, verification and validation (V&V), on-board software can fail with disastrous consequences if it encounters problematic software/hardware interaction or must operate in an unexpected environment. We are using a Bayesian approach to monitor the software and its behavior during operation and provide up-to-date information about the health of the software and its components. The powerful reasoning mechanism provided by our model-based Bayesian approach makes reliable diagnosis of the root causes possible and minimizes the number of false alarms. Compilation of the Bayesian model into compact arithmetic circuits makes SWHM feasible even on platforms with limited CPU power. We show initial results of SWHM on a small simulator of an embedded aircraft software system, where software and sensor faults can be injected.

A second and more promising round of E-health enterprises.

PubMed

Fifer, Sheila K; Thomas, Norrie

2002-11-01

After several years of false starts and failed enterprises, E-medicine is starting to generate practical applications in health care. The new generation of E-businesses is benefiting from the dot-com bust, which has driven away expectations of high financial returns from enterprises based on overblown, ill-fitting models taken from non-health care industries. The more successful new models are adapted to hospital operations and practice patterns, and are backed by money and management indigenous to medicine. However, they are also fragmented, in thus far unconnected pieces of E-network services for discrete clinical activities, such as scripting, lab-testing, patient monitoring, and condition-specific diagnostics and treatment. The new question about E-medicine practice may be not "When will it happen?" but "when will the fragmented E-health systems be connected?"

FPA-FTIR Microspectroscopy for Monitoring Chemotherapy Efficacy in Triple-Negative Breast Cancer

NASA Astrophysics Data System (ADS)

Zawlik, Izabela; Kaznowska, Ewa; Cebulski, Jozef; Kolodziej, Magdalena; Depciuch, Joanna; Vongsvivut, Jitraporn; Cholewa, Marian

2016-11-01

Triple-negative breast cancer is the most aggressive breast cancer subtype with limited treatment options and a poor prognosis. Approximately 70% of triple-negative breast cancer patients fail to achieve a pathologic complete response (pCR) after chemotherapy due to the lack of targeted therapies for this subtype. We report here the development of a focal-plane-array Fourier transform infrared (FPA-FTIR) microspectroscopic technique combined with principal component analysis (PCA) for monitoring chemotherapy effects in triple-negative breast cancer patients. The PCA results obtained using the FPA-FTIR spectral data collected from the same patients before and after the chemotherapy revealed discriminatory features that were consistent with the pathologic and clinical responses to chemotherapy, indicating the potential of the technique as a monitoring tool for observing chemotherapy efficacy.

Association rule mining on grid monitoring data to detect error sources

NASA Astrophysics Data System (ADS)

Maier, Gerhild; Schiffers, Michael; Kranzlmueller, Dieter; Gaidioz, Benjamin

2010-04-01

Error handling is a crucial task in an infrastructure as complex as a grid. There are several monitoring tools put in place, which report failing grid jobs including exit codes. However, the exit codes do not always denote the actual fault, which caused the job failure. Human time and knowledge is required to manually trace back errors to the real fault underlying an error. We perform association rule mining on grid job monitoring data to automatically retrieve knowledge about the grid components' behavior by taking dependencies between grid job characteristics into account. Therewith, problematic grid components are located automatically and this information - expressed by association rules - is visualized in a web interface. This work achieves a decrease in time for fault recovery and yields an improvement of a grid's reliability.

PACS quality control and automatic problem notifier

NASA Astrophysics Data System (ADS)

Honeyman-Buck, Janice C.; Jones, Douglas; Frost, Meryll M.; Staab, Edward V.

1997-05-01

One side effect of installing a clinical PACS Is that users become dependent upon the technology and in some cases it can be very difficult to revert back to a film based system if components fail. The nature of system failures range from slow deterioration of function as seen in the loss of monitor luminance through sudden catastrophic loss of the entire PACS networks. This paper describes the quality control procedures in place at the University of Florida and the automatic notification system that alerts PACS personnel when a failure has happened or is anticipated. The goal is to recover from a failure with a minimum of downtime and no data loss. Routine quality control is practiced on all aspects of PACS, from acquisition, through network routing, through display, and including archiving. Whenever possible, the system components perform self and between platform checks for active processes, file system status, errors in log files, and system uptime. When an error is detected or a exception occurs, an automatic page is sent to a pager with a diagnostic code. Documentation on each code, trouble shooting procedures, and repairs are kept on an intranet server accessible only to people involved in maintaining the PACS. In addition to the automatic paging system for error conditions, acquisition is assured by an automatic fax report sent on a daily basis to all technologists acquiring PACS images to be used as a cross check that all studies are archived prior to being removed from the acquisition systems. Daily quality control is preformed to assure that studies can be moved from each acquisition and contrast adjustment. The results of selected quality control reports will be presented. The intranet documentation server will be described with the automatic pager system. Monitor quality control reports will be described and the cost of quality control will be quantified. As PACS is accepted as a clinical tool, the same standards of quality control must be established as are expected on other equipment used in the diagnostic process.

Superiority of automatic remote monitoring compared with in-person evaluation for scheduled ICD follow-up in the TRUST trial - testing execution of the recommendations.

PubMed

Varma, Niraj; Michalski, Justin; Stambler, Bruce; Pavri, Behzad B

2014-05-21

To test recommended implantable cardioverter defibrillator (ICD) follow-up methods by 'in-person evaluations' (IPE) vs. 'remote Home Monitoring' (HM). ICD patients were randomized 2:1 to automatic HM or to Conventional monitoring, with follow-up checks scheduled at 3, 6, 9, 12, and 15 months post-implant. Conventional patients were evaluated with IPE only. Home Monitoring patients were assessed remotely only for 1 year between 3 and 15 month evaluations. Adherence to follow-up was measured. HM and Conventional patients were similar (age 63 years, 72% male, left ventricular ejection fraction 29%, primary prevention 73%, DDD 57%). Conventional management suffered greater patient attrition during the trial (20.1 vs. 14.2% in HM, P = 0.007). Three month follow-up occurred in 84% in both groups. There was 100% adherence (5 of 5 checks) in 47.3% Conventional vs. 59.7% HM (P < 0.001). Between 3 and 15 months, HM exhibited superior (2.2×) adherence to scheduled follow-up [incidence of failed follow up was 146 of 2421 (6.0%) in HM vs. 145 of 1098 (13.2%) in Conventional, P < 0.001] and punctuality. In HM (daily transmission success rate median 91%), transmission loss caused only 22 of 2275 (0.97%) failed HM evaluations between 3 and 15 months; others resulted from clinic oversight. Overall IPE failure rate in Conventional [193 of 1841 (10.5%) exceeded that in HM [97 of 1484 (6.5%), P < 0.001] by 62%, i.e. HM patients remained more loyal to IPE when this was mandated. Automatic remote monitoring better preserves patient retention and adherence to scheduled follow-up compared with IPE. NCT00336284. © The Author 2014. Published by Oxford University Press on behalf of the European Society of Cardiology.

Relationships between Executive Functioning and Homework Difficulties in Students with and without Autism Spectrum Disorder: An Analysis of Student- and Parent-Reports

ERIC Educational Resources Information Center

Endedijk, Hinke; Denessen, Eddie; Hendriks, Angelique W.

2011-01-01

Despite the fact that homework forms an important cornerstone of student development, many students fail to capitalize on the long-term benefits of doing homework. Several executive skills, including cognitive flexibility, monitoring and planning are suggested as prerequisites for the completion of homework. It follows that homework difficulties…

30 CFR 250.270 - What decisions will MMS make on the DPP or DOCD and within what timeframe?

Code of Federal Regulations, 2011 CFR

2011-07-01

..., REGULATION, AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Review and Decision Process for the Dpp Or Docd § 250.270... provide monitoring information. (2) Require you to modify your proposed DPP or DOCD It fails to make...

30 CFR 550.270 - What decisions will BOEM make on the DPP or DOCD and within what timeframe?

Code of Federal Regulations, 2014 CFR

2014-07-01

... MANAGEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Plans and Information Review and Decision Process for the Dpp Or Docd § 550.270 What decisions... provide monitoring information. (2) Require you to modify your proposed DPP or DOCD, It fails to make...

Imaging of paediatric splenic injury with contrast-enhanced ultrasonography.

PubMed

Oldenburg, Anja; Hohmann, Joachim; Skrok, Jan; Albrecht, Thomas

2004-04-01

We report two children who sustained traumatic parenchymal splenic injury and were monitored with contrast-enhanced ultrasound (CEUS). In both cases, unenhanced US failed to diagnose splenic haematoma, but the injury was well demonstrated after injection of contrast agent. In one case agreement with CT was excellent; in the other, CT was not performed due to the comprehensive information provided by CEUS.

When Does Memory Monitoring Succeed versus Fail? Comparing Item-Specific and Relational Encoding in the DRM Paradigm

ERIC Educational Resources Information Center

Huff, Mark J.; Bodner, Glen E.

2013-01-01

We compared the effects of item-specific versus relational encoding on recognition memory in the Deese-Roediger-McDermott paradigm. In Experiment 1, we directly compared item-specific and relational encoding instructions, whereas in Experiments 2 and 3 we biased pleasantness and generation tasks, respectively, toward one or the other type of…

The implementation of fail-operative functions in integrated digital avionics systems

NASA Technical Reports Server (NTRS)

Osoer, S. S.

1976-01-01

System architectures which incorporate fail operative flight guidance functions within a total integrated avionics complex are described. It is shown that the mixture of flight critical and nonflight critical functions within a common computer complex is an efficient solution to the integration of navigation, guidance, flight control, display, and flight management. Interfacing subsystems retain autonomous capability to avoid vulnerability to total avionics system shutdown as a result of only a few failures.

Does academic assessment system type affect levels of academic stress in medical students? A cross-sectional study from Pakistan

PubMed Central

Ali, Madiha; Asim, Hamna; Edhi, Ahmed Iqbal; Hashmi, Muhammad Daniyal; Khan, Muhammad Shahjahan; Naz, Farah; Qaiser, Kanza Noor; Qureshi, Sidra Masud; Zahid, Mohammad Faizan; Jehan, Imtiaz

2015-01-01

Introduction Stress among medical students induced by academic pressures is on the rise among the student population in Pakistan and other parts of the world. Our study examined the relationship between two different systems employed to assess academic performance and the levels of stress among students at two different medical schools in Karachi, Pakistan. Methods A sample consisting of 387 medical students enrolled in pre-clinical years was taken from two universities, one employing the semester examination system with grade point average (GPA) scores (a tiered system) and the other employing an annual examination system with only pass/fail grading. A pre-designed, self-administered questionnaire was distributed. Test anxiety levels were assessed by The Westside Test Anxiety Scale (WTAS). Overall stress was evaluated using the Perceived Stress Scale (PSS). Results There were 82 males and 301 females while four did not respond to the gender question. The mean age of the entire cohort was 19.7±1.0 years. A total of 98 participants were from the pass/fail assessment system while 289 were from the GPA system. There was a higher proportion of females in the GPA system (85% vs. 59%; p<0.01). Students in the pass/fail assessment system had a lower score on the WTAS (2.4±0.8 vs. 2.8±0.7; p=0.01) and the PSS (17.0±6.7 vs. 20.3±6.8; p<0.01), indicating lower levels of test anxiety and overall stress than in students enrolled in the GPA assessment system. More students in the pass/fail system were satisfied with their performance than those in the GPA system. Conclusion Based on the present study, we suggest governing bodies to revise and employ a uniform assessment system for all the medical colleges to improve student academic performance and at the same time reduce stress levels. Our results indicate that the pass/fail assessment system accomplishes these objectives. PMID:26112353

On-line Bayesian model updating for structural health monitoring

NASA Astrophysics Data System (ADS)

Rocchetta, Roberto; Broggi, Matteo; Huchet, Quentin; Patelli, Edoardo

2018-03-01

Fatigue induced cracks is a dangerous failure mechanism which affects mechanical components subject to alternating load cycles. System health monitoring should be adopted to identify cracks which can jeopardise the structure. Real-time damage detection may fail in the identification of the cracks due to different sources of uncertainty which have been poorly assessed or even fully neglected. In this paper, a novel efficient and robust procedure is used for the detection of cracks locations and lengths in mechanical components. A Bayesian model updating framework is employed, which allows accounting for relevant sources of uncertainty. The idea underpinning the approach is to identify the most probable crack consistent with the experimental measurements. To tackle the computational cost of the Bayesian approach an emulator is adopted for replacing the computationally costly Finite Element model. To improve the overall robustness of the procedure, different numerical likelihoods, measurement noises and imprecision in the value of model parameters are analysed and their effects quantified. The accuracy of the stochastic updating and the efficiency of the numerical procedure are discussed. An experimental aluminium frame and on a numerical model of a typical car suspension arm are used to demonstrate the applicability of the approach.

Monitoring Hitting Load in Tennis Using Inertial Sensors and Machine Learning.

PubMed

Whiteside, David; Cant, Olivia; Connolly, Molly; Reid, Machar

2017-10-01

Quantifying external workload is fundamental to training prescription in sport. In tennis, global positioning data are imprecise and fail to capture hitting loads. The current gold standard (manual notation) is time intensive and often not possible given players' heavy travel schedules. To develop an automated stroke-classification system to help quantify hitting load in tennis. Nineteen athletes wore an inertial measurement unit (IMU) on their wrist during 66 video-recorded training sessions. Video footage was manually notated such that known shot type (serve, rally forehand, slice forehand, forehand volley, rally backhand, slice backhand, backhand volley, smash, or false positive) was associated with the corresponding IMU data for 28,582 shots. Six types of machine-learning models were then constructed to classify true shot type from the IMU signals. Across 10-fold cross-validation, a cubic-kernel support vector machine classified binned shots (overhead, forehand, or backhand) with an accuracy of 97.4%. A second cubic-kernel support vector machine achieved 93.2% accuracy when classifying all 9 shot types. With a view to monitoring external load, the combination of miniature inertial sensors and machine learning offers a practical and automated method of quantifying shot counts and discriminating shot types in elite tennis players.

Development of advanced seal verification

NASA Technical Reports Server (NTRS)

Workman, Gary L.; Kosten, Susan E.; Abushagur, Mustafa A.

1992-01-01

The purpose of this research is to develop a technique to monitor and insure seal integrity with a sensor that has no active elements to burn-out during a long duration activity, such as a leakage test or especially during a mission in space. The original concept proposed is that by implementing fiber optic sensors, changes in the integrity of a seal can be monitored in real time and at no time should the optical fiber sensor fail. The electrical components which provide optical excitation and detection through the fiber are not part of the seal; hence, if these electrical components fail, they can be easily changed without breaking the seal. The optical connections required for the concept to work does present a functional problem to work out. The utility of the optical fiber sensor for seal monitoring should be general enough that the degradation of a seal can be determined before catastrophic failure occurs and appropriate action taken. Two parallel efforts were performed in determining the feasibility of using optical fiber sensors for seal verification. In one study, research on interferometric measurements of the mechanical response of the optical fiber sensors to seal integrity was studied. In a second study, the implementation of the optical fiber to a typical vacuum chamber was implemented and feasibility studies on microbend experiments in the vacuum chamber were performed. Also, an attempt was made to quantify the amount of pressure actually being applied to the optical fiber using finite element analysis software by Algor.

Current and future management of treatment failure in low- and middle-income countries.

PubMed

Boyd, Mark A

2010-01-01

Access to second-line therapy in low- and middle-income countries has been limited to date. The WHO predicts that between 500 000 and 800 000 HIV-infected people on first-line combination antiretroviral therapy will require switch to second-line therapy by 2010. This paper aims to describe and review access to second-line therapy in low- and middle-income countries at present and examine future possibilities. The majority of HIV-infected patients failing first-line combination antiretroviral therapy is identified by way of routine monitoring of clinical and immunological status as a surrogate for virological monitoring. Evidence suggests that immunological and clinical monitoring lack both sensitivity and specificity for virological failure. Consequently, at treatment failure, patients have often selected a degree of resistance within the nucleoside/nucleotide reverse transcriptase inhibitor class that questions the efficacy of using nucleoside/nucleotide reverse transcriptase inhibitors in a second-line regimen. There is a paucity of good-quality evidence on which to base guidelines and policy. Optimally, a second-line regimen would be simple, potent, tolerable and lend itself to provision according to the successful 'public health' approach. Provision of second-line therapy to HIV-infected individuals failing first-line therapy is a major challenge to the ongoing success of access to HIV care programmes in low- and middle-income countries. The optimal second-line combination antiretroviral therapies are unknown. Research trials to help define best practice are in advanced stages of development and implementation.

Physical Therapists’ Perceptions of Knowledge and Clinical Behavior Regarding Cardiovascular Disease Prevention

PubMed Central

Van Zant, R Scott; Cape, Kelly Jo; Roach, Katrina; Sweeney, Janie

2013-01-01

Purpose The study purpose was to assess perceptions of physical therapists (PTs) regarding the role of physical therapy in cardiovascular disease (CVD) prevention. Methods A 25-item survey, validated by expert cardiovascular/pulmonary (CVP) PTs, was sent electronically to 2,673 PTs. Each item represented an element of clinical practice behavior: education of CVD/risk factors (EDCVD), administration of primary CVD prevention (PRECVD), identifying underlying CVD/risk factors (IDCVD), monitoring CV status in patients with CVD (MONCVD). Responses were assigned numeric values (strongly agree = 5 to strongly disagree = 1), and mean element scores were analyzed. Results Most of the 516 respondents were APTA Section members (34% CVP Section, 42% other Section membership) and worked in academia (53%). Items showing a high (> 95%) level of agreement included patient education of smoking (97%) and monitoring exercise intensity (99%), assessing exercise benefits (99%), clinically identifying obesity (97%) and hypertension (97%), and monitoring CV response to exercise (99%). Items failing to reach 80% overall agreement were patient education of CVD medications (79%) and blood chemistry (72%), and assessing CVD family history (75%), patient BMI (60%), and body composition (33%). Identifying underlying CVD (77.2%) was the only practice behavior failing to reach 80% agreement. Outpatient PTs agreed significantly less to all elements vs. academics, and to IDCVD vs. all PTs except home health. Conclusions Physical therapists support most CVD prevention behaviors, but not given elements of patient education and identifying underlying CVD/risk factors. PMID:23801901

Assessing the skill of seasonal meteorological forecast products for predicting droughts and water scarcity in highly regulated basins

NASA Astrophysics Data System (ADS)

Squeri, Marika; Giuliani, Matteo; Castelletti, Andrea; Pulido-Velazquez, Manuel; Marcos-Garcia, Patricia; Macian-Sorribes, Hector

2017-04-01

Drought and water scarcity are important issues in Southern Europe and many predictions suggest that their frequency and severity will increase over the next years, potentially leading to negative environmental and socio-economic impacts. This work focuses on the Jucar river basin, located in the hinterland of Valencia (Eastern Spain), which is historically affected by long and severe dry periods that negatively impact several economic sectors, with irrigated agriculture representing the main consumptive demand in the basin (79%). Monitoring drought and water scarcity is crucial to activate timely drought management strategies in the basin. However, most traditional drought indexes fail in detecting critical events due to the large presence of human regulation supporting the irrigated agriculture. Over the last 20 years, a sophisticated drought monitoring system has been set up to properly capture the status of the catchment by means of the state index, a weighted linear combination of twelve indicators that depends on observations of precipitation, streamflow, reservoirs' storages and groundwater levels in representative locations at the basin. In this work, we explore the possibility of predicting the state index, which is currently used only as a monitoring tool, in order to prompt anticipatory actions before the drought/water scarcity event starts. In particular, we test the forecasting skill of retrospective seasonal meteorological predictions from the European Centre for Medium-range Weather Forecasts (ECMWF) System 4. The 7-months lead time of these products allows predicting in February the values of the state index until September, thus covering the entire agricultural season. Preliminary results suggest that the Sys4-ECMWF products are skillful in predicting the state index, potentially supporting the design of anticipatory drought management actions.

Fiber Bragg Grating Based System for Temperature Measurements

NASA Astrophysics Data System (ADS)

Tahir, Bashir Ahmed; Ali, Jalil; Abdul Rahman, Rosly

In this study, a fiber Bragg grating sensor for temperature measurement is proposed and experimentally demonstrated. In particular, we point out that the method is well-suited for monitoring temperature because they are able to withstand a high temperature environment, where standard thermocouple methods fail. The interrogation technologies of the sensor systems are all simple, low cost and effective as well. In the sensor system, fiber grating was dipped into a water beaker that was placed on a hotplate to control the temperature of water. The temperature was raised in equal increments. The sensing principle is based on tracking of Bragg wavelength shifts caused by the temperature change. So the temperature is measured based on the wavelength-shifts of the FBG induced by the heating water. The fiber grating is high temperature stable excimer-laser-induced grating and has a linear function of wavelength-temperature in the range of 0-285°C. A dynamic range of 0-285°C and a sensitivity of 0.0131 nm/°C almost equal to that of general FBG have been obtained by this sensor system. Furthermore, the correlation of theoretical analysis and experimental results show the capability and feasibility of the purposed technique.

Lessons Learned from the Space Shuttle Engine Cutoff System (ECO) Anomalies

NASA Technical Reports Server (NTRS)

Martinez, Hugo E.; Welzyn, Ken

2011-01-01

The Space Shuttle Orbiter's main engine cutoff (ECO) system first failed ground checkout in April, 2005 during a first tanking test prior to Return-to-Flight. Despite significant troubleshooting and investigative efforts that followed, the root cause could not be found and intermittent anomalies continued to plague the Program. By implementing hardware upgrades, enhancing monitoring capability, and relaxing the launch rules, the Shuttle fleet was allowed to continue flying in spite of these unexplained failures. Root cause was finally determined following the launch attempts of STS-122 in December, 2007 when the anomalies repeated, which allowed drag-on instrumentation to pinpoint the fault (the ET feedthrough connector). The suspect hardware was removed and provided additional evidence towards root cause determination. Corrective action was implemented and the system has performed successfully since then. This white paper presents the lessons learned from the entire experience, beginning with the anomalies since Return-to-Flight through discovery and correction of the problem. To put these lessons in better perspective for the reader, an overview of the ECO system is presented first. Next, a chronological account of the failures and associated investigation activities is discussed. Root cause and corrective action are summarized, followed by the lessons learned.

Great Teachers: The Internal and External Characteristics that Sustain Them

ERIC Educational Resources Information Center

Gennerman, Theresa

2009-01-01

For a century, school reform has been a topic of local and federal government efforts. While the reforms have evolved and changed to a small degree during this time, the deficit focus of reform has been consistent, failing schools and failing systems. Education's focus on the deficits within the system has yielded reform that has yet to succeed in…

Control of a Wheeled Transport Robot with Two Steerable Wheels

NASA Astrophysics Data System (ADS)

Larin, V. B.

2017-09-01

The control of a system with one actuator failed is studied. The problem of control of a wheeled transport robot with two steerable wheels of which the rear one is stuck (its drive has failed) is solved. An algorithm for controlling the system in this situation is proposed. The effectiveness of the algorithm is demonstrated by way of an example.

New Developments in FPGA: SEUs and Fail-Safe Strategies from the NASA Goddard Perspective

NASA Technical Reports Server (NTRS)

Berg, Melanie D.; Label, Kenneth A.; Pellish, Jonathan

2016-01-01

It has been shown that, when exposed to radiation environments, each Field Programmable Gate Array (FPGA) device has unique error signatures. Subsequently, fail-safe and mitigation strategies will differ per FPGA type. In this session several design approaches for safe systems will be presented. It will also explore the benefits and limitations of several mitigation techniques. The intention of the presentation is to provide information regarding FPGA types, their susceptibilities, and proven fail-safe strategies; so that users can select appropriate mitigation and perform the required trade for system insertion. The presentation will describe three types of FPGA devices and their susceptibilities in radiation environments.

New Developments in FPGA: SEUs and Fail-Safe Strategies from the NASA Goddard Perspective

NASA Technical Reports Server (NTRS)

Berg, Melanie D.; LaBel, Kenneth; Pellish, Jonathan

2015-01-01

It has been shown that, when exposed to radiation environments, each Field Programmable Gate Array (FPGA) device has unique error signatures. Subsequently, fail-safe and mitigation strategies will differ per FPGA type. In this session several design approaches for safe systems will be presented. It will also explore the benefits and limitations of several mitigation techniques. The intention of the presentation is to provide information regarding FPGA types, their susceptibilities, and proven fail-safe strategies; so that users can select appropriate mitigation and perform the required trade for system insertion. The presentation will describe three types of FPGA devices and their susceptibilities in radiation environments.

Attempting to control mite allergens with mechanical ventilation and dehumidification in British houses.

PubMed

Niven, R; Fletcher, A M; Pickering, A C; Custovic, A; Sivour, J B; Preece, A R; Oldham, L A; Francis, H C

1999-05-01

Allergen avoidance is of considerable interest in the treatment and even prevention of asthma. Attempts to control house dust mites have included environmental manipulation in homes in an attempt to reduce humidity below a level that favors mite survival. This appears to have some benefit in Scandinavia, but a previous attempt with mechanical ventilation heat pump recovery (MVHR) units in the UK failed to achieve the desired results. We report a study using an additional central dehumidification modification of the MVHR (MVHRcd) in an attempt to reduce allergen levels in houses of asthmatic subjects. Ten houses of asthmatic patients allergic to dust mites and 10 architectural control houses were studied. The active houses were fitted with an MVHRcd unit in November/December 1994 and activated in January 1995. The active and control houses were monitored continuously for internal temperature and humidity by using digital sensors in the asthmatic and control bedrooms. Dust samples were collected to determine allergen levels at baseline (January 1994) and 3, 6, 9, and 15 months after switching on the units. The winter seasonal average humidity fell from 50% relative humidity (RH) in control bedrooms to 37% RH in asthmatic bedrooms compared with 72% RH in the ambient air as measured on the intake of the MVHRcd systems. There was no corresponding change in seasonal mean temperature within the houses. Although the temperature and humidity weekly and seasonal means remained below the study target of 45% RH or 7 g/kg absolute humidity at 21 degrees C, there were transient rises in humidity detected by the sensors in the houses with MVHRcd systems. Allergen levels fell both in active and control houses during the study period, but there was no significant advantage gained from the installation of MVHRcd systems. The MVHRcd system failed to confer a benefit in terms of mite allergen reduction despite apparently adequate control of temperature and humidity.

Use of an Airway Exchange Catheter-Assisted Extubation With Continuous End-Tidal Carbon Dioxide Monitoring in a Pediatric Patient With a Known Difficult Airway: A Case Report.

PubMed

Yegian, Courtney C; Volz, Lana M; Galgon, Richard E

2018-05-11

Tracheal extubation in children with known difficult airways is associated with an increased risk of adverse events. Currently, there is no reliable measure to predict the need for emergent reintubation due to airway inadequacy. Airway exchange catheter-assisted extubation has been shown to be a useful adjunct in decreasing the risk of adverse events due to failed extubation. We report a case of using an airway exchange catheter-assisted extubation with continuous end-tidal carbon dioxide monitoring for a pediatric patient with a known difficult airway.

Obesity Prevention and Weight Maintenance After Loss.

PubMed

German, Alexander James

2016-09-01

Obesity is one of the most prevalent medical diseases in pets. Outcomes are often disappointing; many animals either fail to reach target weight or regain weight. This article discusses managing obesity, focusing on prevention. It gives guidance on establishing monitoring programs that use regular body weight and condition assessments to identify animals at risk of inappropriate weight gain, enabling early intervention. Weight management in obese animals is a lifelong process. Regular weight and body condition monitoring are key to identifying animals that rebound early, while continuing to feed a therapeutic weight loss diet can help prevent it from happening. Copyright © 2016 Elsevier Inc. All rights reserved.

What happens to Palestine refugees with diabetes mellitus in a primary healthcare centre in Jordan who fail to attend a quarterly clinic appointment?

PubMed

Khader, Ali; Ballout, Ghada; Shahin, Yousef; Hababeh, Majed; Farajallah, Loai; Zeidan, Wafaa; Abu-Zayed, Ishtaiwi; Kochi, Arata; Harries, Anthony D; Zachariah, Rony; Kapur, Anil; Shaikh, Irshad; Seita, Akihiro

2014-03-01

In a primary healthcare clinic in Jordan to determine: (i) treatment outcomes stratified by baseline characteristics of all patients with diabetes mellitus (DM) ever registered as of June 2012 and (ii) in those who failed to attend the clinic in the quarter (April-June 2012), the number who repeatedly did not attend in subsequent quarters up to 1 year later, again stratified by baseline characteristics. A retrospective cohort study with treatment outcome data collected and analysed using e-health and the cohort analysis approach in UNRWA Nuzha Primary Health Care Clinic for Palestine refugees, Amman, Jordan. As of June 2012, there were 2974 patients with DM ever registered, of whom 2246 (76%) attended the clinic, 279 (9%) did not attend, 81 (3%) died, 67 (2%) were transferred out and 301 (10%) were lost to follow-up. A higher proportion of males and patients with undetermined or poor disease control failed to attend the clinic compared with those who attended the clinic. Of the 279 patients who did not attend the clinic in quarter 2, 2012, 144 (52%) were never seen for four consecutive quarters and were therefore defined as lost to follow-up. There were a few differences between patients who were lost to follow-up and those who re-attended at another visit that included some variation in age and fewer disease-related complications amongst those who were lost to follow-up. This study endorses the value of e-health and cohort analysis for monitoring and managing patients with DM. Just over half of patients who fail to attend a scheduled quarterly appointment are declared lost to follow-up 1 year later, and systems need to be set up to identify and contact such patients so that those who are late for their appointments can be brought back to care and those who might have died or silently transferred out can be correctly recorded. © 2014 John Wiley & Sons Ltd.

Evaluation of wireless stimulation of the endocardium, WiSE, technology for treatment heart failure.

PubMed

Seifert, M; Butter, C

2016-06-01

There are several unsolved limitations in delivering cardiac resynchronization therapy. 30-40% of patients fail to have any clinical benefit after 6 months caused by different reasons. Endocardial stimulation rather than conventional epicardial pacing has been shown to: be more physiologically, improve electrical stimulation of the left ventricular, give less dispersion of repolarisation and result in better resynchronization. The Wireless Cardiac Stimulation in Left Ventricle, WiCS-LV, system provides an option for wireless, left ventricular endocardial pacing triggered from a conventional right ventricular pacing spike from a co-implant. Expert commentary: The feasibility of the WiCS-LV system has been successfully demonstrated in a population of failed cardiac resynchronization patients, either failed implantation procedure of a conventional system, non-responder to conventional therapy or upgrade from pacemaker or defibrillator, where a conventional system was not an option. WiCS-LV is innovative technology with promising safety, performance and preliminary efficacy.

A Secure and Robust User Authenticated Key Agreement Scheme for Hierarchical Multi-medical Server Environment in TMIS.

PubMed

Das, Ashok Kumar; Odelu, Vanga; Goswami, Adrijit

2015-09-01

The telecare medicine information system (TMIS) helps the patients to gain the health monitoring facility at home and access medical services over the Internet of mobile networks. Recently, Amin and Biswas presented a smart card based user authentication and key agreement security protocol usable for TMIS system using the cryptographic one-way hash function and biohashing function, and claimed that their scheme is secure against all possible attacks. Though their scheme is efficient due to usage of one-way hash function, we show that their scheme has several security pitfalls and design flaws, such as (1) it fails to protect privileged-insider attack, (2) it fails to protect strong replay attack, (3) it fails to protect strong man-in-the-middle attack, (4) it has design flaw in user registration phase, (5) it has design flaw in login phase, (6) it has design flaw in password change phase, (7) it lacks of supporting biometric update phase, and (8) it has flaws in formal security analysis. In order to withstand these security pitfalls and design flaws, we aim to propose a secure and robust user authenticated key agreement scheme for the hierarchical multi-server environment suitable in TMIS using the cryptographic one-way hash function and fuzzy extractor. Through the rigorous security analysis including the formal security analysis using the widely-accepted Burrows-Abadi-Needham (BAN) logic, the formal security analysis under the random oracle model and the informal security analysis, we show that our scheme is secure against possible known attacks. Furthermore, we simulate our scheme using the most-widely accepted and used Automated Validation of Internet Security Protocols and Applications (AVISPA) tool. The simulation results show that our scheme is also secure. Our scheme is more efficient in computation and communication as compared to Amin-Biswas's scheme and other related schemes. In addition, our scheme supports extra functionality features as compared to other related schemes. As a result, our scheme is very appropriate for practical applications in TMIS.

Keep Talking & Monitoring: the importance of longitudinal research & community-based monitoring to support sustainable land management in southern Africa

NASA Astrophysics Data System (ADS)

Dougill, Andrew; Stringer, Lindsay

2015-04-01

Projects come and go with researchers, development practioners and government staff initiating new forms of community engagement in environmental monitoring and land management practices. We analyse interventions from Botswana and Swaziland and highlight that for benefits to be long-lived and lead to sustainable land management, requires community engagement in project design, implementation and for project outputs to be used in developing community-led environmental monitoring tools that can then help to guide local decision-making systems. We stress the vital importance of continued participatory engagement of researchers with community leaders and key government staff beyond the timeframe of their initial research such that longitudinal research approaches can realise significant benefits to all concerned. In dynamic (non-equilibrium) dryland environments, it is vitally important that research approaches address temporal and spatial variability by mapping patterns of change, using a range of participatory tools to enhance understandings of the causes of land degradation and the opportunities for shifts towards more sustainable land management. Decision-support tools, such as rangeland assessment guides produced for various Kalahari rangeland settings in Botswana (via a UNEP project and affiliated research), provide opportunities to support more sustainable land management. However, at present benefits are not being fully realised as project and research staff move on after projects end. Similarly, findings from mixed farming systems in Swaziland (assessing a JICA-funded project) show problems in maintaining new institutional structures to manage rangeland degradation, whilst issues on arable areas associated with parasitic weeds (Striga asiatica) remain problematic. Findings from longitudinal research in Swaziland also show that community understandings of environmental problems have evolved over 10 years and identify new problems associated with intensified drought events linked to climate change. Returning to communities (even if irregularly) after project completion enables identification of local-level knowledge and institutional problems that are often the underlying cause of the post-project failings. In many cases, such failings have led to a lack of sustained benefits as significant community-level goodwill and knowledge is developed during projects, but limited input and guidance through remaining institutional channels means that any strong grounding for success is not harnessed or sustained. It is vital that researchers work pro-actively with formal state institutions (notably agricultural extension services) to ensure that research and development project outputs are understood and used in the post-project phase. Continued engagement with local and institutional actors through longitudinal research assessing multi-stakeholder partnerships and local management practices can realise significant additional benefits far beyond the small time and cost implications of such continued engagement. Shifts to trans-disciplinary, multi-stakeholder working need to address the need for such longer-term, longitudinal research processes to ensure that benefits are not immediately lost and that new forms of sustainable land management can indeed be sustained.

Challenging the assumption of habitat limitation: An example from centrarchid fishes over an intermediate spatial scale

USGS Publications Warehouse

Gutreuter, S.

2004-01-01

Habitat rehabilitation efforts are predicated on the frequently untested assumption that habitat is limiting to populations. These efforts are typically costly and will be ineffective if habitat is not limiting. Therefore it is important to assess, rather than assume, habitat limitation wherever habitat rehabilitation projects are considered. Catch-count data from a standardized probability-based stratified-random monitoring programme were examined for indirect evidence of backwater habitat limitation by centrarchid fishes in the Upper Mississippi River System. The monitoring design enabled fitting statistical models of the association between mean catch at the spatial scale of tens of river kilometres and the percentage of contiguous aquatic area in backwater at least 1 m deep by maximizing a stratum-area weighted negative binomial log-likelihood function. Statistical models containing effects for backwater limitation failed to account for substantial variation in the data. However, 95% confidence intervals on the backwater parameter estimates excluded zero, indicating that population abundance may be limited by backwater prevalence where backwaters are extremely scarce. The combined results indicate, at most, a weak signal of backwater limitation where backwaters are extremely scarce in the lower reaches, but not elsewhere in the Upper Mississippi River System. This suggests that habitat restoration projects designed to increase the area of backwaters suitable for winter survival of centrarchids are unlikely to produce measurable benefits over intermediate spatial scales in much of the Upper Mississippi River System, and indicates the importance of correct identification of limiting processes. Published in 2004 by John Wiley and Sons, Ltd.

Performance of Particulate Containment at Nanotechnology Workplaces

PubMed Central

Lo, Li-Ming; Tsai, Candace S.-J.; Dunn, Kevin H.; Hammond, Duane; Marlow, David; Topmiller, Jennifer; Ellenbecker, Michael

2015-01-01

The evaluation of engineering controls for the production or use of carbon nanotubes (CNTs) was investigated at two facilities. These controls assessments are necessary to evaluate the current status of control performance and to develop proper control strategies for these workplaces. The control systems evaluated in these studies included ventilated enclosures, exterior hoods, and exhaust filtration systems. Activity-based monitoring with direct-reading instruments and filter sampling for microscopy analysis were used to evaluate the effectiveness of control measures at study sites. Our study results showed that weighing CNTs inside the biological safety cabinet can have a 37% reduction on the particle concentration in the worker’s breathing zone, and produce a 42% lower area concentration outside the enclosure. The ventilated enclosures used to reduce fugitive emissions from the production furnaces exhibited good containment characteristics when closed, but they failed to contain emissions effectively when opened during product removal/harvesting. The exhaust filtration systems employed for exhausting these ventilated enclosures did not provide promised collection efficiencies for removing engineered nanomaterials from furnace exhaust. The exterior hoods were found to be a challenge for controlling emissions from machining nanocomposites: the downdraft hood effectively contained and removed particles released from the manual cutting process, but using the canopy hood for powered cutting of nanocomposites created 15%–20% higher ultrafine (<500 nm) particle concentrations at the source and at the worker’s breathing zone. The microscopy analysis showed that CNTs can only be found at production sources but not at the worker breathing zones during the tasks monitored. PMID:26705393

A Fully Automated Drosophila Olfactory Classical Conditioning and Testing System for Behavioral Learning and Memory Assessment

PubMed Central

Jiang, Hui; Hanna, Eriny; Gatto, Cheryl L.; Page, Terry L.; Bhuva, Bharat; Broadie, Kendal

2016-01-01

Background Aversive olfactory classical conditioning has been the standard method to assess Drosophila learning and memory behavior for decades, yet training and testing are conducted manually under exceedingly labor-intensive conditions. To overcome this severe limitation, a fully automated, inexpensive system has been developed, which allows accurate and efficient Pavlovian associative learning/memory analyses for high-throughput pharmacological and genetic studies. New Method The automated system employs a linear actuator coupled to an odorant T-maze with airflow-mediated transfer of animals between training and testing stages. Odorant, airflow and electrical shock delivery are automatically administered and monitored during training trials. Control software allows operator-input variables to define parameters of Drosophila learning, short-term memory and long-term memory assays. Results The approach allows accurate learning/memory determinations with operational fail-safes. Automated learning indices (immediately post-training) and memory indices (after 24 hours) are comparable to traditional manual experiments, while minimizing experimenter involvement. Comparison with Existing Methods The automated system provides vast improvements over labor-intensive manual approaches with no experimenter involvement required during either training or testing phases. It provides quality control tracking of airflow rates, odorant delivery and electrical shock treatments, and an expanded platform for high-throughput studies of combinational drug tests and genetic screens. The design uses inexpensive hardware and software for a total cost of ~$500US, making it affordable to a wide range of investigators. Conclusions This study demonstrates the design, construction and testing of a fully automated Drosophila olfactory classical association apparatus to provide low-labor, high-fidelity, quality-monitored, high-throughput and inexpensive learning and memory behavioral assays. PMID:26703418

A fully automated Drosophila olfactory classical conditioning and testing system for behavioral learning and memory assessment.

PubMed

Jiang, Hui; Hanna, Eriny; Gatto, Cheryl L; Page, Terry L; Bhuva, Bharat; Broadie, Kendal

2016-03-01

Aversive olfactory classical conditioning has been the standard method to assess Drosophila learning and memory behavior for decades, yet training and testing are conducted manually under exceedingly labor-intensive conditions. To overcome this severe limitation, a fully automated, inexpensive system has been developed, which allows accurate and efficient Pavlovian associative learning/memory analyses for high-throughput pharmacological and genetic studies. The automated system employs a linear actuator coupled to an odorant T-maze with airflow-mediated transfer of animals between training and testing stages. Odorant, airflow and electrical shock delivery are automatically administered and monitored during training trials. Control software allows operator-input variables to define parameters of Drosophila learning, short-term memory and long-term memory assays. The approach allows accurate learning/memory determinations with operational fail-safes. Automated learning indices (immediately post-training) and memory indices (after 24h) are comparable to traditional manual experiments, while minimizing experimenter involvement. The automated system provides vast improvements over labor-intensive manual approaches with no experimenter involvement required during either training or testing phases. It provides quality control tracking of airflow rates, odorant delivery and electrical shock treatments, and an expanded platform for high-throughput studies of combinational drug tests and genetic screens. The design uses inexpensive hardware and software for a total cost of ∼$500US, making it affordable to a wide range of investigators. This study demonstrates the design, construction and testing of a fully automated Drosophila olfactory classical association apparatus to provide low-labor, high-fidelity, quality-monitored, high-throughput and inexpensive learning and memory behavioral assays. Copyright © 2015 Elsevier B.V. All rights reserved.

Bottom-up, decision support system development : a wetlandsalinity management application in California's San Joaquin Valley

DOE Office of Scientific and Technical Information (OSTI.GOV)

Quinn, Nigel W.T.

Seasonally managed wetlands in the Grasslands Basin ofCalifornia's San Joaquin Valley provide food and shelter for migratorywildfowl during winter months and sport for waterfowl hunters during theannual duck season. Surface water supply to these wetland contain saltwhich, when drained to the San Joaquin River during the annual drawdownperiod, negatively impacts downstream agricultural riparian waterdiverters. Recent environmental regulation, limiting discharges salinityto the San Joaquin River and primarily targeting agricultural non-pointsources, now addresses return flows from seasonally managed wetlands.Real-time water quality management has been advocated as a means ofmatching wetland return flows to the assimilative capacity of the SanJoaquin River. Past attemptsmore » to build environmental monitoring anddecision support systems to implement this concept have failed forreasons that are discussed in this paper. These reasons are discussed inthe context of more general challenges facing the successfulimplementation of environmental monitoring, modelling and decisionsupport systems. The paper then provides details of a current researchand development project which will ultimately provide wetland managerswith the means of matching salt exports with the available assimilativecapacity of the San Joaquin River, when fully implemented. Manipulationof the traditional wetland drawdown comes at a potential cost to thesustainability of optimal wetland moist soil plant habitat in thesewetlands - hence the project provides appropriate data and a feedback andresponse mechanism for wetland managers to balance improvements to SanJoaquin River quality with internally-generated information on the healthof the wetland resource. The author concludes the paper by arguing thatthe architecture of the current project decision support system, whencoupled with recent advances in environmental data acquisition, dataprocessing and information dissemination technology, holds significantpromise to address some of the problems described earlier in the paperthat have limited past efforts to improve Basin water qualitymanagement.« less

Automation and quality assurance of the production cycle

NASA Astrophysics Data System (ADS)

Hajdu, L.; Didenko, L.; Lauret, J.

2010-04-01

Processing datasets on the order of tens of terabytes is an onerous task, faced by production coordinators everywhere. Users solicit data productions and, especially for simulation data, the vast amount of parameters (and sometime incomplete requests) point at the need for a tracking, control and archiving all requests made so a coordinated handling could be made by the production team. With the advent of grid computing the parallel processing power has increased but traceability has also become increasing problematic due to the heterogeneous nature of Grids. Any one of a number of components may fail invalidating the job or execution flow in various stages of completion and re-submission of a few of the multitude of jobs (keeping the entire dataset production consistency) a difficult and tedious process. From the definition of the workflow to its execution, there is a strong need for validation, tracking, monitoring and reporting of problems. To ease the process of requesting production workflow, STAR has implemented several components addressing the full workflow consistency. A Web based online submission request module, implemented using Drupal's Content Management System API, enforces ahead that all parameters are described in advance in a uniform fashion. Upon submission, all jobs are independently tracked and (sometime experiment-specific) discrepancies are detected and recorded providing detailed information on where/how/when the job failed. Aggregate information on success and failure are also provided in near real-time.

Stabilization Lessons Learned from Sierra Leone

DTIC Science & Technology

2013-12-01

Reduction Project (0704–0188) Washington, DC 20503. 1. AGENCY USE ONLY (Leave blank) 2. REPORT DATE December 2013 3. REPORT TYPE AND DATES...Force Commander DRC Democratic Republic of the Congo ECOWAS Economic Community of West African States ECOMOG ECOWAS Monitoring Group JIC... Community of West African States (ECOWAS) tried and failed to implement cease-fires and resolve the conflict.1 After Nigeria and the ECOWAS mission

Determining the factors associated with seedling herbivory on afforested carbon sequestration sites in the Lower Mississippi Alluvial Valley: preliminary results

Treesearch

Daniel C. Sumerall; Donald L. Grebner; Jeanne C. Jones; Stephen C. Grado; Richard P. Maiers; Keith L. Belli

2010-01-01

One causal factor of failed afforestation attempts in the Lower Mississippi Alluvial Valley (LMAV) is mammalian herbivory. Herbivory of seedlings generally reduces growth and can also lead to seedling mortality. Seedlings were randomly selected for monitoring throughout the first growing season. Growth and survival data were recorded, as were signs of mammalian...

Comparison of four methods of establishing control limits for monitoring quality controls in infectious disease serology testing.

PubMed

Dimech, Wayne; Karakaltsas, Marina; Vincini, Giuseppe A

2018-05-25

A general trend towards conducting infectious disease serology testing in centralized laboratories means that quality control (QC) principles used for clinical chemistry testing are applied to infectious disease testing. However, no systematic assessment of methods used to establish QC limits has been applied to infectious disease serology testing. A total of 103 QC data sets, obtained from six different infectious disease serology analytes, were parsed through standard methods for establishing statistical control limits, including guidelines from Public Health England, USA Clinical and Laboratory Standards Institute (CLSI), German Richtlinien der Bundesärztekammer (RiliBÄK) and Australian QConnect. The percentage of QC results failing each method was compared. The percentage of data sets having more than 20% of QC results failing Westgard rules when the first 20 results were used to calculate the mean±2 standard deviation (SD) ranged from 3 (2.9%) for R4S to 66 (64.1%) for 10X rule, whereas the percentage ranged from 0 (0%) for R4S to 32 (40.5%) for 10X when the first 100 results were used to calculate the mean±2 SD. By contrast, the percentage of data sets with >20% failing the RiliBÄK control limits was 25 (24.3%). Only two data sets (1.9%) had more than 20% of results outside the QConnect Limits. The rate of failure of QCs using QConnect Limits was more applicable for monitoring infectious disease serology testing compared with UK Public Health, CLSI and RiliBÄK, as the alternatives to QConnect Limits reported an unacceptably high percentage of failures across the 103 data sets.

Large Crater Repair at Silver Flag Exercise Site, Tyndall Air Force Base, Florida

DTIC Science & Technology

2015-08-01

fiberglass mat ( FFM ) survived medium-speed braking events and was deemed suitable for use on taxiways and aprons. 2. The current USAF FFM system failed...braking events due to failure of the connector bushings. After replacement with more robust connector bushings from the FFM system, the FRP system...withstood the high-speed taxi events that caused the FFM to fail. ERDC/GSL TR-15-27 2 4. AM2 aluminum matting was successfully tested as a suitable

Flight test and evaluation of Omega navigation for general aviation

NASA Technical Reports Server (NTRS)

Hwoschinsky, P. V.

1975-01-01

A seventy hour flight test program was performed to determine the suitability and accuracy of a low cost Omega navigation receiver in a general aviation aircraft. An analysis was made of signal availability in two widely separated geographic areas. Comparison is made of the results of these flights with other navigation systems. Conclusions drawn from the test experience indicate that developmental system improvement is necessary before a competent fail safe or fail soft area navigation system is offered to general aviation.

New Developments in FPGA Devices: SEUs and Fail-Safe Strategies from the NASA Goddard Perspective

NASA Technical Reports Server (NTRS)

Berg, Melanie; LaBel, Kenneth; Pellish, Jonathan

2016-01-01

It has been shown that, when exposed to radiation environments, each Field Programmable Gate Array (FPGA) device has unique error signatures. Subsequently, fail-safe and mitigation strategies will differ per FPGA type. In this session several design approaches for safe systems will be presented. It will also explore the benefits and limitations of several mitigation techniques. The intention of the presentation is to provide information regarding FPGA types, their susceptibilities, and proven fail-safe strategies; so that users can select appropriate mitigation and perform the required trade for system insertion. The presentation will describe three types of FPGA devices and their susceptibilities in radiation environments.

Can enforced behaviour change attitudes: exploring the influence of Intelligent Speed Adaptation.

PubMed

Chorlton, Kathryn; Conner, Mark

2012-09-01

The Theory of Planned Behaviour model (Ajzen, 1985) was used to determine whether long-term experience with Intelligent Speed Adaption (ISA) prompts a change in speed related cognitions. The study examines data collected as part of a project examining driver behaviour with an intervening but overridable ISA system. Data was collected in four six-month field trials. The trials followed an A-B-A design (28 days driving with no ISA, 112 days driving with ISA, 28 days driving without ISA) to monitor changes in speeding behaviour as a result of the ISA system and any carry-over effect of the system. Findings suggested that following experience with the system, drivers' intention to speed significantly weakened, beyond the removal of ISA support. Drivers were also less likely to believe that exceeding the speed would 'get them to their destination more quickly' and less likely to believe that 'being in a hurry' would facilitate speeding. However, the positive change in intentions and beliefs failed to translate into behaviour. Experience with the ISA system significantly reduced the percentage of distance travelled whilst exceeding the speed limit but this effect was not evident when the ISA support was removed. Copyright © 2010 Elsevier Ltd. All rights reserved.

Evaluation of the axonics modulation technologies sacral neuromodulation system for the treatment of urinary and fecal dysfunction.

PubMed

Cohn, Joshua A; Kowalik, Casey G; Kaufman, Melissa R; Reynolds, W Stuart; Milam, Douglas F; Dmochowski, Roger R

2017-01-01

Sacral neuromodulation (SNM) remains one of the few effective treatments for refractory bladder and bowel dysfunction. However, SNM is associated with frequent need for surgical intervention, in many cases because of a failed battery. A rechargeable SNM system, with a manufacturer-reported battery life of 15 years or more, has entered post-market clinical testing in Europe but has not yet been approved for clinical testing in the United States. Areas covered: We review existing neuromodulation technologies for the treatment of lower urinary tract and bowel dysfunction and explore the limitations of available technology. In addition, we discuss implantation technique and device specifications and programming of the rechargeable SNM system in detail. Lastly, we present existing evidence for the use of SNM in bladder and bowel dysfunction and evaluate the anticipated trajectory of neuromodulation technologies over the next five years. Expert commentary: A rechargeable system for SNM is a welcome technological advance. However surgical revision not related to battery changes is not uncommon. Therefore, while a rechargeable system would be expected to reduce costs, it will not eliminate the ongoing maintenance associated with neuromodulation. No matter the apparent benefits, all new technologies require extensive post-market monitoring to ensure safety and efficacy.

Remote monitoring of implantable cardioverter-defibrillators. Problems and implications using a telemonitoring system.

PubMed

Siebermair, J; Clauss, S; Martens, E; Schuessler, F; Oversohl, N; Haserueck, N; Estner, H L; Kääb, S; Wakili, R

2015-04-01

The rising number of implantable devices has led to an increase in device-related workload, e.g., regular interrogation follow-up visits. Telemonitoring systems for implantable cardioverter-defibrillators (ICDs) seem to be a promising tool for reducing workload and costs, and they have the potential of optimizing patient care. However, issues such as practical functionality of ICD telemonitoring in daily routine may affect its broad implementation. The objective of this study was to evaluate potential problems during the implementation of a telemonitoring system, Medtronic CareLink™ (CL™) with respect to the installation and data transmission process. A total of 159 patients with ICDs who were equipped with the CL™ system were evaluated and followed up for 16 months regarding the success rate of the first data transmission via the telemonitoring system. In this cohort, a high rate of nontransmission of 23.9 % was observed after the 16-month follow-up. A detailed interview of these patients (no transmission) revealed that the main reasons for failed transmissions were due to the patients' loss of interest in the concept (approximately 50 %) as well as technical problems (approximately 25 %) with setting up the system. These results indicate that telemonitoring systems bear potential problems and that the evaluation of patient motivation and technical support options seems to play an important role in establishing the functionality of these systems.

Cerebral Palsy Litigation

PubMed Central

Sartwelle, Thomas P.

2015-01-01

The cardinal driver of cerebral palsy litigation is electronic fetal monitoring, which has continued unabated for 40 years. Electronic fetal monitoring, however, is based on 19th-century childbirth myths, a virtually nonexistent scientific foundation, and has a false positive rate exceeding 99%. It has not affected the incidence of cerebral palsy. Electronic fetal monitoring has, however, increased the cesarian section rate, with the expected increase in mortality and morbidity risks to mothers and babies alike. This article explains why electronic fetal monitoring remains endorsed as efficacious in the worlds’ labor rooms and courtrooms despite being such a feeble medical modality. It also reviews the reasons professional organizations have failed to condemn the use of electronic fetal monitoring in courtrooms. The failures of tort reform, special cerebral palsy courts, and damage limits to stem the escalating litigation are discussed. Finally, the authors propose using a currently available evidence rule—the Daubert doctrine that excludes “junk science” from the courtroom—as the beginning of the end to cerebral palsy litigation and electronic fetal monitoring’s 40-year masquerade as science. PMID:25183322

Investigation of photoplethysmographic signals and blood oxygen saturation values on healthy volunteers during cuff-induced hypoperfusion using a multimode PPG/SpO₂ sensor.

PubMed

Shafique, M; Kyriacou, P A; Pal, S K

2012-06-01

Photoplethysmography (PPG) is a technique widely used to monitor volumetric blood changes induced by cardiac pulsations. Pulse oximetry uses the technique of PPG to estimate arterial oxygen saturation values (SpO₂). In poorly perfused tissues, SpO₂ readings may be compromised due to the poor quality of the PPG signals. A multimode finger PPG probe that operates simultaneously in reflectance, transmittance and a combined mode called "transreflectance" was developed, in an effort to improve the quality of the PPG signals in states of hypoperfusion. Experiments on 20 volunteers were conducted to evaluate the performance of the multimode PPG sensor and compare the results with a commercial transmittance pulse oximeter. A brachial blood pressure cuff was used to induce artificial hypoperfusion. Results showed that the amplitude of the transreflectance AC PPG signals were significantly different (p < 0.05) than the AC PPG signals obtained from the other two conventional PPG sensors (reflectance and transmittance). At induced brachial pressures between 90 and 135 mmHg, the reflectance finger pulse oximeter failed 25 times (failure rate 42.2 %) to estimate SpO₂ values, whereas the transmittance pulse oximeter failed 8 times (failure rate 15.5 %). The transreflectance pulse oximeter failed only 3 times (failure rate 6.8 %) and the commercial pulse oximeter failed 17 times (failure rate 29.4 %).

Does WIC work? The effects of WIC on pregnancy and birth outcomes.

PubMed

Bitler, Marianne P; Currie, Janet

2005-01-01

Support for WIC, the Special Supplemental Nutrition Program for Women, Infants, and Children, is based on the belief that "WIC works." This consensus has lately been questioned by researchers who point out that most WIC research fails to properly control for selection into the program. This paper evaluates the selection problem using rich data from the national Pregnancy Risk Assessment Monitoring System. We show that relative to Medicaid mothers, all of whom are eligible for WIC, WIC participants are negatively selected on a wide array of observable dimensions, and yet WIC participation is associated with improved birth outcomes, even after controlling for observables and for a full set of state-year interactions intended to capture unobservables that vary at the state-year level. The positive impacts of WIC are larger among subsets of even more disadvantaged women, such as those who received public assistance last year, single high school dropouts, and teen mothers.

Indirect reciprocity can overcome free-rider problems on costly moral assessment.

PubMed

Sasaki, Tatsuya; Okada, Isamu; Nakai, Yutaka

2016-07-01

Indirect reciprocity is one of the major mechanisms of the evolution of cooperation. Because constant monitoring and accurate evaluation in moral assessments tend to be costly, indirect reciprocity can be exploited by cost evaders. A recent study crucially showed that a cooperative state achieved by indirect reciprocators is easily destabilized by cost evaders in the case with no supportive mechanism. Here, we present a simple and widely applicable solution that considers pre-assessment of cost evaders. In the pre-assessment, those who fail to pay for costly assessment systems are assigned a nasty image that leads to them being rejected by discriminators. We demonstrate that considering the pre-assessment can crucially stabilize reciprocal cooperation for a broad range of indirect reciprocity models. In particular for the most leading social norms, we analyse the conditions under which a prosocial state becomes locally stable. © 2016 The Authors.

Validated methodology for quantifying infestation levels of dreissenid mussels in environmental DNA (eDNA) samples.

PubMed

Peñarrubia, Luis; Alcaraz, Carles; Vaate, Abraham Bij de; Sanz, Nuria; Pla, Carles; Vidal, Oriol; Viñas, Jordi

2016-12-14

The zebra mussel (Dreissena polymorpha Pallas, 1771) and the quagga mussel (D. rostriformis Deshayes, 1838) are successful invasive bivalves with substantial ecological and economic impacts in freshwater systems once they become established. Since their eradication is extremely difficult, their detection at an early stage is crucial to prevent spread. In this study, we optimized and validated a qPCR detection method based on the histone H2B gene to quantify combined infestation levels of zebra and quagga mussels in environmental DNA samples. Our results show specific dreissenid DNA present in filtered water samples for which microscopic diagnostic identification for larvae failed. Monitoring a large number of locations for invasive dreissenid species based on a highly specific environmental DNA qPCR assay may prove to be an essential tool for management and control plans focused on prevention of establishment of dreissenid mussels in new locations.

Validated methodology for quantifying infestation levels of dreissenid mussels in environmental DNA (eDNA) samples

PubMed Central

Peñarrubia, Luis; Alcaraz, Carles; Vaate, Abraham bij de; Sanz, Nuria; Pla, Carles; Vidal, Oriol; Viñas, Jordi

2016-01-01

The zebra mussel (Dreissena polymorpha Pallas, 1771) and the quagga mussel (D. rostriformis Deshayes, 1838) are successful invasive bivalves with substantial ecological and economic impacts in freshwater systems once they become established. Since their eradication is extremely difficult, their detection at an early stage is crucial to prevent spread. In this study, we optimized and validated a qPCR detection method based on the histone H2B gene to quantify combined infestation levels of zebra and quagga mussels in environmental DNA samples. Our results show specific dreissenid DNA present in filtered water samples for which microscopic diagnostic identification for larvae failed. Monitoring a large number of locations for invasive dreissenid species based on a highly specific environmental DNA qPCR assay may prove to be an essential tool for management and control plans focused on prevention of establishment of dreissenid mussels in new locations. PMID:27966602

Development of Instruments and Evaluative Procedures on Contributors to Illness and Health.

PubMed

Cloninger, C Robert; Cloninger, Kevin M

2011-09-01

Instruments available for a person-centered assessment of the causes of well-being and ill-being are described. Monitoring at the level of symptoms of illness and past lifestyle behavior has failed to promote change in well-being in a strong and consistent way. Therefore, we illustrate a way of assessing the interactions among multiple aspects of the causes of well-being. For example, at least three distinct aspects of human well-being are known to interact synergistically to promote health - neurobiological plasticity, self-regulatory functioning and virtue. The neglect of any one of the ternary aspects of well-being impedes understanding and treatment of the whole person. Each aspect can be reliably measured using quantitative and qualitative techniques to facilitate treatment planning and analysis of their interactions as a complex adaptive system, although further work is needed to clarify the content and structure of each aspect.

Development of Instruments and Evaluative Procedures on Contributors to Illness and Health.

PubMed

Cloninger, C Robert; Cloninger, Kevin M

Instruments available for a person-centered assessment of the causes of well-being and ill-being are described. Monitoring at the level of symptoms of illness and past lifestyle behavior has failed to promote change in well-being in a strong and consistent way. Therefore, we illustrate a way of assessing the interactions among multiple aspects of the causes of well-being. For example, at least three distinct aspects of human well-being are known to interact synergistically to promote health - neurobiological plasticity, self-regulatory functioning and virtue. The neglect of any one of the ternary aspects of well-being impedes understanding and treatment of the whole person. Each aspect can be reliably measured using quantitative and qualitative techniques to facilitate treatment planning and analysis of their interactions as a complex adaptive system, although further work is needed to clarify the content and structure of each aspect.

The levers of influence.

PubMed

Martin, W

1999-01-01

Physicians often determine the demand for health care services, as well as control the clinical processes aimed at improving health outcomes at the individual and population level. Given their important role in enhancing health status and improving the health care delivery system, it is critical that physician executives master the tools necessary to positively influence physician behavior. But changing behavior is far more complex than "doing it or not doing it." The Nike slogan "just do it" is motivating, but over-simplified. The roots of human change include: consciousness-raising, emotional arousal, commitment, helping relationships, self-reevaluation, reward, and environmental control. A model to effectively influence behavior is presented and includes setting clear expectations, measuring and monitoring performance, providing feedback, and rewarding and recognizing improvement. If all else fails, try discipline. This five-step approach is based on the science of human behavior and working with physicians in diverse settings, ranging from academic medical centers to small practices.

Electronic logic for enhanced switch reliability

DOEpatents

Cooper, J.A.

1984-01-20

A logic circuit is used to enhance redundant switch reliability. Two or more switches are monitored for logical high or low output. The output for the logic circuit produces a redundant and fail-safe representation of the switch outputs. When both switch outputs are high, the output is high. Similarly, when both switch outputs are low, the logic circuit's output is low. When the output states of the two switches do not agree, the circuit resolves the conflict by memorizing the last output state which both switches were simultaneously in and produces the logical complement of this output state. Thus, the logic circuit of the present invention allows the redundant switches to be treated as if they were in parallel when the switches are open and as if they were in series when the switches are closed. A failsafe system having maximum reliability is thereby produced.

Informing the market: the strengths and weaknesses of information in the British National Health Service.

PubMed

McKee, M; Chenet, L

1997-06-01

Many countries are experimenting with planned (or quasi-) markets to discover if they can efficiently deliver health care in keeping with societal objectives. This paper examines the information requirements of this approach. Information is necessary in order to compare the performance of providers, to support billing, and to monitor access to care. It should be accurate, unambiguous, and resistant to manipulation. We draw on a project to find out how information on hospitalisation could be used in contracting in the British National Health Service. We conclude that the existing British system fails to provide robust measures of how many patients are treated, for what conditions, and with what treatments. We identify some promising remedies, others that are more difficult, and some which may be impossible to implement in any planned market, given the uncertainty of clinical practice.

Volcanic crystals as time capsules of eruption history.

PubMed

Ubide, Teresa; Kamber, Balz S

2018-01-23

Crystals formed prior to a volcanic event can provide evidence of processes leading to and timing of eruptions. Clinopyroxene is common in basaltic to intermediate volcanoes, however, its ability as a recorder of pre-eruptive histories has remained comparatively underexplored. Here we show that novel high-resolution trace element images of clinopyroxene track eruption triggers and timescales at Mount Etna (Sicily, Italy). Chromium (Cr) distribution in clinopyroxene from 1974 to 2014 eruptions reveals punctuated episodes of intrusion of primitive magma at depth. Magma mixing efficiently triggered volcanism (success rate up to 90%), within only 2 weeks of arrival of mafic intrusions. Clinopyroxene zonations distinguish between injections of mafic magma and regular recharges with more evolved magma, which often fail to tip the system to erupt. High Cr zonations can therefore be used to reconstruct past eruptions and inform responses to geophysical signals of volcano unrest, potentially offering an additional approach to volcano hazard monitoring.

A novel treatment approach to infected nonunion of long bones without systemic antibiotics.

PubMed

Masrouha, Karim Z; Raad, Michael E; Saghieh, Said S

2018-04-01

Infected nonunion of long bones may require intravenous antibiotics over a lengthy period which may result in a high rate of complications. This study aims to assess the efficacy of local antibiotics used as a replacement to prolonged intravenous therapy. Thirteen patients with infected nonunion of long bones who failed at least one previous surgery were included. The infection was treated through extensive debridement, application of antibiotic-impregnated calcium sulphate pellets and the bone stabilized with external fixation. These patients were monitored for union and infection by clinical signs, laboratory values, and radiographs over a period of 24 months. The results support an eradication of infection and union in all patients with no antibiotic-associated complications. Local antibiotic delivery using calcium sulphate pellets provides an effective method for treatment of nonunion in long bones and is free of the complications from the intravenous route.

SLC-off Landsat-7 ETM+ reflective band radiometric calibration

USGS Publications Warehouse

Markham, B.L.; Barsi, J.A.; Thome, K.J.; Barker, J.L.; Scaramuzza, P.L.; Helder, D.L.; ,

2005-01-01

Since May 31, 2003, when the scan line corrector (SLC) on the Landsat-7 ETM+ failed, the primary foci of Landsat-7 ETM+ analyses have been on understanding and attempting to fix the problem and later on developing composited products to mitigate the problem. In the meantime, the Image Assessment System personnel and vicarious calibration teams have continued to monitor the radiometric performance of the ETM+ reflective bands. The SLC failure produced no measurable change in the radiometric calibration of the ETM+ bands. No trends in the calibration are definitively present over the mission lifetime, and, if present, are less than 0.5% per year. Detector 12 in Band 7 dropped about 0.5% in response relative to the rest of the detectors in the band in May 2004 and recovered back to within 0.1% of its initial relative gain in October 2004.

The need for congressional action to finance arsenic reductions in drinking water.

PubMed

Levine, Rebecca Leah

2012-11-01

Many public water systems in the U.S. are unsafe because the communities cannot afford to comply with the current 10 parts per billion (ppb) federal arsenic standard for drinking water. Communities unable to afford improvements remain vulnerable to adverse health effects associated with higher levels of arsenic exposure. Scientific and bipartisan political consensus exists that the arsenic standard should not be less stringent than 10 ppb, and new data suggest additional adverse health effects related to arsenic exposure through drinking water. Congress has failed to reauthorize the Drinking Water State Revolving Fund program to provide reliable funding to promote compliance and reduce the risk of adverse health effects. Congress's recent ad hoc appropriations do not allow long-term planning and ongoing monitoring and maintenance. Investing in water infrastructure will lower health care costs and create American jobs. Delaying necessary upgrades will only increase the costs of improvements over time.

A study of elevated temperature testing techniques for the fatigue behavior of PMCS: Application to T650-35/AMB21

NASA Technical Reports Server (NTRS)

Gyekenyesi, Andrew L.; Gastelli, Michael G.; Ellis, John R.; Burke, Christopher S.

1995-01-01

An experimental study was conducted to investigate the mechanical behavior of a T650-35/AMB21 eight-harness satin weave polymer composite system. Emphasis was placed on the development and refinement of techniques used in elevated temperature uniaxial PMC testing. Issues such as specimen design, gripping, strain measurement, and temperature control and measurement were addressed. Quasi-static tensile and fatigue properties (R(sub sigma) = 0.1) were examined at room and elevated temperatures. Stiffness degradation and strain accumulation during fatigue cycling were recorded to monitor damage progression and provide insight for future analytical modeling efforts. Accomplishments included an untabbed dog-bone specimen design which consistently failed in the gage section, accurate temperature control and assessment, and continuous in-situ strain measurement capability during fatigue loading at elevated temperatures. Finally, strain accumulation and stiffness degradation during fatigue cycling appeared to be good indicators of damage progression.

Automations influence on nuclear power plants: a look at three accidents and how automation played a role.

PubMed

Schmitt, Kara

2012-01-01

Nuclear power is one of the ways that we can design an efficient sustainable future. Automation is the primary system used to assist operators in the task of monitoring and controlling nuclear power plants (NPP). Automation performs tasks such as assessing the status of the plant's operations as well as making real time life critical situational specific decisions. While the advantages and disadvantages of automation are well studied in variety of domains, accidents remind us that there is still vulnerability to unknown variables. This paper will look at the effects of automation within three NPP accidents and incidents and will consider why automation failed in preventing these accidents from occurring. It will also review the accidents at the Three Mile Island, Chernobyl, and Fukushima Daiichi NPP's in order to determine where better use of automation could have resulted in a more desirable outcome.

Methods for improved forewarning of condition changes in monitoring physical processes

DOEpatents

Hively, Lee M.

2013-04-09

This invention teaches further improvements in methods for forewarning of critical events via phase-space dissimilarity analysis of data from biomedical equipment, mechanical devices, and other physical processes. One improvement involves objective determination of a forewarning threshold (U.sub.FW), together with a failure-onset threshold (U.sub.FAIL) corresponding to a normalized value of a composite measure (C) of dissimilarity; and providing a visual or audible indication to a human observer of failure forewarning and/or failure onset. Another improvement relates to symbolization of the data according the binary numbers representing the slope between adjacent data points. Another improvement relates to adding measures of dissimilarity based on state-to-state dynamical changes of the system. And still another improvement relates to using a Shannon entropy as the measure of condition change in lieu of a connected or unconnected phase space.

Occurence of adverse events due to continuous glucose monitoring.

PubMed

Jadviscokova, Tereza; Fajkusova, Zuzana; Pallayova, Maria; Luza, Jiri; Kuzmina, Galina

2007-12-01

Continuous glucose monitoring (CGM) using transcutaneous sensors is becoming a sophisticated method to control and regulate glucose metabolism. The transcutaneous sensor of the CGM system (CGMS Medtronic Minimed, Northridge, CA, USA) is chosen to measure glucose concentration in interstitial fluid up to three days after insertion even though its function remains stable for a longer period. The question arises, which factors really limit the period of sensor insertion without unnecessary risk. The aim of this study was to assess any adverse events occurring in the course of 9 days after the sensor insertion. In a group of 22 healthy volunteers aged 21.8+/-1.30 y (mean +/- SE) a total of 26 sensors was inserted subcutaneously in gluteal or lumbar region for 9 days. Before insertion the site was sprayed with an antiseptic (Cutasept F, Bode Chemie, Hamburg, Germany). Local adverse reactions and disturbances in general condition were examined. In the course of 184 sensor-days, there were only minor local adverse events: hypersensitivity, itching, pain, redness, burning, subcutaneous hemorrhage. Additionally, sleep disturbances, attention deficits, problems related to the CGMS monitor, to adhesive tape and/or sensor were found. None of these resulted in sensor withdrawal. In 12 volunteers (55 %) no complications were observed. The sensor function measured according to electrical signals (ISIG) failed (always on day 1-2) in 4 cases (16 %). The present FDA approved 3-day insertion period for Medtronic transcutaneous sensor does not seem to limit its use and appears to be worth a careful revision.

Cohort monitoring of persons with hypertension: an illustrated example from a primary healthcare clinic for Palestine refugees in Jordan.

PubMed

Khader, Ali; Farajallah, Loai; Shahin, Yousef; Hababeh, Majed; Abu-Zayed, Ishtaiwi; Kochi, Arata; Harries, Anthony D; Zachariah, Rony; Kapur, Anil; Venter, Wendy; Seita, Akihiro

2012-09-01

Recording and reporting systems borrowed from the DOTS framework for tuberculosis control can be used to record, monitor and report on chronic disease. In a primary healthcare clinic run by UNRWA in Amman, Jordan, serving Palestine refugees with hypertension, we set out to illustrate the method of cohort reporting for persons with hypertension by presenting on quarterly and cumulative case finding, cumulative and 12-month analysis of cohort outcomes and to assess how these data may inform and improve the quality of hypertension care services. This was a descriptive study using routine programme data collected through E-Health. There were 97 newly registered patients with hypertension in quarter 1, 2012, and a total of 4130 patients with hypertension ever registered since E-Health started in October 2009. By 31 March 2012, 3119 (76%) of 4130 patients were retained in care, 878 (21%) had failed to present to a healthcare worker in the last 3 months and the remainder had died, transferred out or were lost to follow-up. Cumulative and 12-month cohort outcome analysis indicated deficiencies in several components of clinical performance related to blood pressure measurements and fasting blood glucose tests to screen simultaneously for diabetes. Between 8% and 15% of patients with HT had serious complications such as cardiovascular disease and stroke. Cohort analysis is a valuable tool for the monitoring and management of non-communicable chronic diseases such as HT. © 2012 Blackwell Publishing Ltd.

Does Nonlinear Modeling Play a Role in Plasmid Bioprocess Monitoring Using Fourier Transform Infrared Spectra?

PubMed

Lopes, Marta B; Calado, Cecília R C; Figueiredo, Mário A T; Bioucas-Dias, José M

2017-06-01

The monitoring of biopharmaceutical products using Fourier transform infrared (FT-IR) spectroscopy relies on calibration techniques involving the acquisition of spectra of bioprocess samples along the process. The most commonly used method for that purpose is partial least squares (PLS) regression, under the assumption that a linear model is valid. Despite being successful in the presence of small nonlinearities, linear methods may fail in the presence of strong nonlinearities. This paper studies the potential usefulness of nonlinear regression methods for predicting, from in situ near-infrared (NIR) and mid-infrared (MIR) spectra acquired in high-throughput mode, biomass and plasmid concentrations in Escherichia coli DH5-α cultures producing the plasmid model pVAX-LacZ. The linear methods PLS and ridge regression (RR) are compared with their kernel (nonlinear) versions, kPLS and kRR, as well as with the (also nonlinear) relevance vector machine (RVM) and Gaussian process regression (GPR). For the systems studied, RR provided better predictive performances compared to the remaining methods. Moreover, the results point to further investigation based on larger data sets whenever differences in predictive accuracy between a linear method and its kernelized version could not be found. The use of nonlinear methods, however, shall be judged regarding the additional computational cost required to tune their additional parameters, especially when the less computationally demanding linear methods herein studied are able to successfully monitor the variables under study.

Intracranial pressure and cerebral perfusion pressure monitoring in non-TBI patients: special considerations.

PubMed

Helbok, Raimund; Olson, DaiWai M; Le Roux, Peter D; Vespa, Paul

2014-12-01

The effect of intracranial pressure (ICP) and the role of ICP monitoring are best studied in traumatic brain injury (TBI). However, a variety of acute neurologic illnesses e.g., subarachnoid hemorrhage, intracerebral hemorrhage, ischemic stroke, meningitis/encephalitis, and select metabolic disorders, e.g., liver failure and malignant, brain tumors can affect ICP. The purpose of this paper is to review the literature about ICP monitoring in conditions other than TBI and to provide recommendations how the technique may be used in patient management. A PubMed search between 1980 and September 2013 identified 989 articles; 225 of which were reviewed in detail. The technique used to monitor ICP in non-TBI conditions is similar to that used in TBI; however, indications for ICP monitoring often are intertwined with the presence of obstructive hydrocephalus and hence the use of ventricular catheters is more frequent. Increased ICP can adversely affect outcome, particularly when it fails to respond to treatment. However, patients with elevated ICP can still have favorable outcomes. Although the influence of ICP-based care on outcome in non-TBI conditions appears less robust than in TBI, monitoring ICP and cerebral perfusion pressure can play a role in guiding therapy in select patients.

Selective stimulation of facial muscles with a penetrating electrode array in the feline model

PubMed Central

Sahyouni, Ronald; Bhatt, Jay; Djalilian, Hamid R.; Tang, William C.; Middlebrooks, John C.; Lin, Harrison W.

2017-01-01

Objective Permanent facial nerve injury is a difficult challenge for both patients and physicians given its potential for debilitating functional, cosmetic, and psychological sequelae. Although current surgical interventions have provided considerable advancements in facial nerve rehabilitation, they often fail to fully address all impairments. We aim to introduce an alternative approach to facial nerve rehabilitation. Study design Acute experiments in animals with normal facial function. Methods The study included three anesthetized cats. Four facial muscles (levator auris longus, orbicularis oculi, nasalis, and orbicularis oris) were monitored with a standard electromyographic (EMG) facial nerve monitoring system with needle electrodes. The main trunk of the facial nerve was exposed and a 16-channel penetrating electrode array was placed into the nerve. Electrical current pulses were delivered to each stimulating electrode individually. Elicited EMG voltage outputs were recorded for each muscle. Results Stimulation through individual channels selectively activated restricted nerve populations, resulting in selective contraction of individual muscles. Increasing stimulation current levels resulted in increasing EMG voltage responses. Typically, selective activation of two or more distinct muscles was successfully achieved via a single placement of the multi-channel electrode array by selection of appropriate stimulation channels. Conclusion We have established in the animal model the ability of a penetrating electrode array to selectively stimulate restricted fiber populations within the facial nerve and to selectively elicit contractions in specific muscles and regions of the face. These results show promise for the development of a facial nerve implant system. PMID:27312936

Glucose metabolism disorder in obese children assessed by continuous glucose monitoring system.

PubMed

Zou, Chao-Chun; Liang, Li; Hong, Fang; Zhao, Zheng-Yan

2008-02-01

Continuous glucose monitoring system (CGMS) can measure glucose levels at 5-minute intervals over a few days, and may be used to detect hypoglycemia, guide insulin therapy, and control glucose levels. This study was undertaken to assess the glucose metabolism disorder by CGMS in obese children. Eighty-four obese children were studied. Interstitial fluid (ISF) glucose levels were measured by CGMS for 24 hours covering the time for oral glucose tolerance test (OGTT). Impaired glucose tolerance (IGT), impaired fasting glucose (IFG), type 2 diabetic mellitus (T2DM) and hypoglycemia were assessed by CGMS. Five children failed to complete CGMS test. The glucose levels in ISF measured by CGMS were highly correlated with those in capillary samples (r=0.775, P<0.001). However, the correlation between ISF and capillary glucose levels was lower during the first hour than that in the later time period (r=0.722 vs r=0.830), and the ISF glucose levels in 69.62% of children were higher than baseline levels in the initial 1-3 hours. In 79 obese children who finished the CGMS, 2 children had IFG, 2 had IGT, 3 had IFG + IGT, and 2 had T2DM. Nocturnal hypoglycemia was noted during the overnight fasting in 11 children (13.92%). Our data suggest that glucose metabolism disorder including hyperglycemia and hypoglycemia is very common in obese children. Further studies are required to improve the precision of the CGMS in children.

Energy drink consumption and the perceived risk and disapproval of drugs: Monitoring the Future, 2010-2016.

PubMed

Jackson, Dylan B; Leal, Wanda E

2018-07-01

Energy drinks have become quite popular in recent years among adolescents, prompting a wealth of recent research examining the potential deleterious consequences of energy drink consumption among youth. The present study adds to this body of work by exploring perceptions of risk and disapproval of soft and hard drugs among adolescents and whether such attitudes are predicted by patterns of energy drink/shot consumption. Data were derived from the seven most recent cohorts (2010-2016) of the Monitoring the Future (MTF) study, a nationally representative survey of U.S. youth. The significance of associations between energy drink/shot consumption and drug perceptions/attitudes was tested using logistic regression techniques employing adjustments for covariates and cohort-specific fixed effects. Energy drink/shot consumption was largely associated with significant increases in the odds of failing to perceive any risk of drug use and failing to disapprove of drug use among youths, regardless of whether attitudes concerning soft or hard drugs were examined. These associations were particularly robust in the case of habitual energy drink/shot consumers (relative to occasional consumers or abstainers). Additional efforts should be made to heighten awareness and education concerning the potential dangers of energy drink consumption among youth, particularly as it pertains to drug attitudes and diminished perceptions of substance use risk. Policies that minimize energy drink consumption among youth as well as programs that educate parents and teachers about the drug attitudes of youths who regularly consume energy drinks and promote active monitoring of these adolescents may be worthwhile. Copyright © 2018 Elsevier B.V. All rights reserved.

Murine norovirus detection in the exhaust air of IVCs is more sensitive than serological analysis of soiled bedding sentinels.

PubMed

Zorn, Julia; Ritter, Bärbel; Miller, Manuel; Kraus, Monika; Northrup, Emily; Brielmeier, Markus

2017-06-01

One limitation to housing rodents in individually ventilated cages (IVCs) is the ineffectiveness of traditional health monitoring programs that test soiled bedding sentinels every quarter. Aerogen transmission does not occur with this method. Moreover, the transmission of numerous pathogens in bedding is uncertain, and sentinel susceptibility to various pathogens varies. A novel method using particle collection from samples of exhaust air was developed in this study which was also systematically compared with routine health monitoring using soiled bedding sentinels. We used our method to screen these samples for the presence of murine norovirus (MNV), a mouse pathogen highly prevalent in laboratory animal facilities. Exhaust air particles from prefilters of IVC racks with known MNV prevalence were tested by quantitative reverse transcription polymerase chain reaction (RT-qPCR). MNV was detected in exhaust air as early as one week with one MNV-positive cage per rack, while sentinels discharged MNV RNA without seroconverting. MNV was reliably and repeatedly detected in particles collected from samples of exhaust air in all seven of the three-month sampling rounds, with increasing MNV prevalence, while sentinels only seroconverted in one round. Under field conditions, routine soiled bedding sentinel health monitoring in our animal facility failed to identify 67% ( n = 85) of positive samples by RT-qPCR of exhaust air particles. Thus, this method proved to be highly sensitive and superior to soiled bedding sentinels in the reliable detection of MNV. These results represent a major breakthrough in hygiene monitoring of rodent IVC systems and contribute to the 3R principles by reducing the number of animals used and by improving experimental conditions.

Failed landings after laying hen flight in a commercial aviary over two flock cycles.

PubMed

Campbell, D L M; Goodwin, S L; Makagon, M M; Swanson, J C; Siegford, J M

2016-01-01

Many egg producers are adopting alternative housing systems such as aviaries that provide hens a tiered cage and a litter-covered open floor area. This larger, more complex environment permits expression of behaviors not seen in space-limited cages, such as flight. Flight is an exercise important for strengthening bones; but domestic hens might display imperfect flight landings due to poor flight control. To assess the potential implications of open space, we evaluated the landing success of Lohmann white laying hens in a commercial aviary. Video recordings of hens were taken from 4 aviary sections at peak lay, mid lay and end lay across two flock cycles. Observations were made in each focal section of all flights throughout the day noting flight origin and landing location (outer perch or litter) and landing success or failure. In Flock 1, 9.1% of all flights failed and 21% failed in Flock 2. The number of flights decreased across the laying cycle for both flocks. Proportionally more failed landings were observed in the double row sections in Flock 2. Collisions with other hens were more common than slipping on the ground or colliding with aviary structures across sections and flocks. More hens slipped on the ground and collided with physical structures at peak lay for Flock 2 than at other time points. More collisions with other hens were seen at mid and end lay than at peak lay for Flock 2. Landings ending on perches failed more often than landings on litter. These results indicate potential for flight-related hen injuries in aviary systems resulting from failed landings, which may have implications for hen welfare and optimal system design and management.

CPLOAS_2 user manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sallaberry, Cedric Jean-Marie.; Helton, Jon Craig

2012-10-01

Weak link (WL)/strong link (SL) systems are important parts of the overall operational design of high-consequence systems. In such designs, the SL system is very robust and is intended to permit operation of the entire system under, and only under, intended conditions. In contrast, the WL system is intended to fail in a predictable and irreversible manner under accident conditions and render the entire system inoperable before an accidental operation of the SL system. The likelihood that the WL system will fail to deactivate the entire system before the SL system fails (i.e., degrades into a configuration that could allowmore » an accidental operation of the entire system) is referred to as probability of loss of assured safety (PLOAS). This report describes the Fortran 90 program CPLOAS_2 that implements the following representations for PLOAS for situations in which both link physical properties and link failure properties are time-dependent: (i) failure of all SLs before failure of any WL, (ii) failure of any SL before failure of any WL, (iii) failure of all SLs before failure of all WLs, and (iv) failure of any SL before failure of all WLs. The effects of aleatory uncertainty and epistemic uncertainty in the definition and numerical evaluation of PLOAS can be included in the calculations performed by CPLOAS_2.« less

Main propulsion system design recommendations for an advanced Orbit Transfer Vehicle

NASA Technical Reports Server (NTRS)

Redd, L.

1985-01-01

Various main propulsion system configurations of an advanced OTV are evaluated with respect to the probability of nonindependent failures, i.e., engine failures that disable the entire main propulsion system. Analysis of the life-cycle cost (LCC) indicates that LCC is sensitive to the main propulsion system reliability, vehicle dry weight, and propellant cost; it is relatively insensitive to the number of missions/overhaul, failures per mission, and EVA and IVA cost. In conclusion, two or three engines are recommended in view of their highest reliability, minimum life-cycle cost, and fail operational/fail safe capability.

Ultra Reliable Closed Loop Life Support for Long Space Missions

NASA Technical Reports Server (NTRS)

Jones, Harry W.; Ewert, Michael K.

2010-01-01

Spacecraft human life support systems can achieve ultra reliability by providing sufficient spares to replace all failed components. The additional mass of spares for ultra reliability is approximately equal to the original system mass, provided that the original system reliability is not too low. Acceptable reliability can be achieved for the Space Shuttle and Space Station by preventive maintenance and by replacing failed units. However, on-demand maintenance and repair requires a logistics supply chain in place to provide the needed spares. In contrast, a Mars or other long space mission must take along all the needed spares, since resupply is not possible. Long missions must achieve ultra reliability, a very low failure rate per hour, since they will take years rather than weeks and cannot be cut short if a failure occurs. Also, distant missions have a much higher mass launch cost per kilogram than near-Earth missions. Achieving ultra reliable spacecraft life support systems with acceptable mass will require a well-planned and extensive development effort. Analysis must determine the reliability requirement and allocate it to subsystems and components. Ultra reliability requires reducing the intrinsic failure causes, providing spares to replace failed components and having "graceful" failure modes. Technologies, components, and materials must be selected and designed for high reliability. Long duration testing is needed to confirm very low failure rates. Systems design should segregate the failure causes in the smallest, most easily replaceable parts. The system must be designed, developed, integrated, and tested with system reliability in mind. Maintenance and reparability of failed units must not add to the probability of failure. The overall system must be tested sufficiently to identify any design errors. A program to develop ultra reliable space life support systems with acceptable mass should start soon since it must be a long term effort.

Health-care process improvement decisions: a systems perspective.

PubMed

Walley, Paul; Silvester, Kate; Mountford, Shaun

2006-01-01

The paper seeks to investigate decision-making processes within hospital improvement activity, to understand how performance measurement systems influence decisions and potentially lead to unsuccessful or unsustainable process changes. A longitudinal study over a 33-month period investigates key events, decisions and outcomes at one medium-sized hospital in the UK. Process improvement events are monitored using process control methods and by direct observation. The authors took a systems perspective of the health-care processes, ensuring that the impacts of decisions across the health-care supply chain were appropriately interpreted. The research uncovers the ways in which measurement systems disguise failed decisions and encourage managers to take a low-risk approach of "symptomatic relief" when trying to improve performance metrics. This prevents many managers from trying higher risk, sustainable process improvement changes. The behaviour of the health-care system is not understood by many managers and this leads to poor analysis of problem situations. Measurement using time-series methodologies, such as statistical process control are vital for a better understanding of the systems impact of changes. Senior managers must also be aware of the behavioural influence of similar performance measurement systems that discourage sustainable improvement. There is a risk that such experiences will tarnish the reputation of performance management as a discipline. Recommends process control measures as a way of creating an organization memory of how decisions affect performance--something that is currently lacking.

Improving imperfect data from health management information systems in Africa using space-time geostatistics.

PubMed

Gething, Peter W; Noor, Abdisalan M; Gikandi, Priscilla W; Ogara, Esther A A; Hay, Simon I; Nixon, Mark S; Snow, Robert W; Atkinson, Peter M

2006-06-01

Reliable and timely information on disease-specific treatment burdens within a health system is critical for the planning and monitoring of service provision. Health management information systems (HMIS) exist to address this need at national scales across Africa but are failing to deliver adequate data because of widespread underreporting by health facilities. Faced with this inadequacy, vital public health decisions often rely on crudely adjusted regional and national estimates of treatment burdens. This study has taken the example of presumed malaria in outpatients within the largely incomplete Kenyan HMIS database and has defined a geostatistical modelling framework that can predict values for all data that are missing through space and time. The resulting complete set can then be used to define treatment burdens for presumed malaria at any level of spatial and temporal aggregation. Validation of the model has shown that these burdens are quantified to an acceptable level of accuracy at the district, provincial, and national scale. The modelling framework presented here provides, to our knowledge for the first time, reliable information from imperfect HMIS data to support evidence-based decision-making at national and sub-national levels.

An astrometric facility for planetary detection on the space station

NASA Technical Reports Server (NTRS)

Nishioka, Kenji; Scargle, Jeffrey D.; Givens, John J.

1987-01-01

An Astrometric Telescope Facility (ATF) for planetary detection is being studied as a potential space station initial operating capability payload. The primary science objective of this mission is the detection and study of planetary systems around other stars. In addition, the facility will be capable of other astrometric measurements such as stellar motions of other galaxies and highly precise direct measurement of stellar distance within the Milky Way Galaxy. The results of a recently completed ATF preliminary systems definition study are summarized. Results of this study indicate that the preliminary concept for the facility is fully capable of meeting the science objective without the development of any new technologies. A simple straightforward operations approach was developed for the ATF. A real-time facility control is not normally required, but does maintain a near real-time ground monitoring capability for the facility and science data stream on a full-time basis. Facility observational sequences are normally loaded once a week. In addition, the preliminary system is designed to be fail-safe and single-fault tolerant. Routine interactions by the space station crew with the ATF will not be necessary, but onboard controls are provided for crew override as required for emergencies and maintenance.

The Effect of Tropopause Seeing on Solar Telescope Site Testing

NASA Astrophysics Data System (ADS)

Beckers, Jacques M.

2017-08-01

The site testing for and seeing correction planning of the 4-m solar telescopes has failed to take into account the significant amount of seeing at tropopause levels (10-20 km altitude).The worst aspect of that seeing layer is its small isoplanatic patch size which at low solar elevations can be significantly less than 1 arcsec. The CLEAR/ATST/DKIST SDIMM seeing monitor is insensitive to this type of seeing. A correction for this missed seeing significantly decreases the measured seeing qualities for the sites tested especially in the early morning and late afternoon. It clearly shows the lake site to be superior with mid-day observations much to be preferred. The small tropopause isoplanatic patch size values also complicate the implementation of the solar MCAO systems aimed at large field-of-view sun imaging. Currently planned systems only correct for lower-layer seeing for which the isoplanatic patch size is about one arc minute. To fully achieve the diffraction limit of the 4-meter class (0.025 arcsec at 500 nm), over a large enough field-of-view to be of scientific interest, complicated Multi-Conjugate Adaptive Optics systems will be needed.

On the period determination of ASAS eclipsing binaries

NASA Astrophysics Data System (ADS)

Mayangsari, L.; Priyatikanto, R.; Putra, M.

2014-03-01

Variable stars, or particularly eclipsing binaries, are very essential astronomical occurrence. Surveys are the backbone of astronomy, and many discoveries of variable stars are the results of surveys. All-Sky Automated Survey (ASAS) is one of the observing projects whose ultimate goal is photometric monitoring of variable stars. Since its first light in 1997, ASAS has collected 50,099 variable stars, with 11,076 eclipsing binaries among them. In the present work we focus on the period determination of the eclipsing binaries. Since the number of data points in each ASAS eclipsing binary light curve is sparse, period determination of any system is a not straightforward process. For 30 samples of such systems we compare the implementation of Lomb-Scargle algorithm which is an Fast Fourier Transform (FFT) basis and Phase Dispersion Minimization (PDM) method which is non-FFT basis to determine their period. It is demonstrated that PDM gives better performance at handling eclipsing detached (ED) systems whose variability are non-sinusoidal. More over, using semi-automatic recipes, we get better period solution and satisfactorily improve 53% of the selected object's light curves, but failed against another 7% of selected objects. In addition, we also highlight 4 interesting objects for further investigation.

Improving Imperfect Data from Health Management Information Systems in Africa Using Space–Time Geostatistics

PubMed Central

Gething, Peter W; Noor, Abdisalan M; Gikandi, Priscilla W; Ogara, Esther A. A; Hay, Simon I; Nixon, Mark S; Snow, Robert W; Atkinson, Peter M

2006-01-01

Background Reliable and timely information on disease-specific treatment burdens within a health system is critical for the planning and monitoring of service provision. Health management information systems (HMIS) exist to address this need at national scales across Africa but are failing to deliver adequate data because of widespread underreporting by health facilities. Faced with this inadequacy, vital public health decisions often rely on crudely adjusted regional and national estimates of treatment burdens. Methods and Findings This study has taken the example of presumed malaria in outpatients within the largely incomplete Kenyan HMIS database and has defined a geostatistical modelling framework that can predict values for all data that are missing through space and time. The resulting complete set can then be used to define treatment burdens for presumed malaria at any level of spatial and temporal aggregation. Validation of the model has shown that these burdens are quantified to an acceptable level of accuracy at the district, provincial, and national scale. Conclusions The modelling framework presented here provides, to our knowledge for the first time, reliable information from imperfect HMIS data to support evidence-based decision-making at national and sub-national levels. PMID:16719557

Around Marshall

NASA Image and Video Library

1983-08-10

One of the main components of the Hubble Space Telescope (HST) is the Solar Array Drive Electronics (SADE) system. This system interfaces with the Support System Module (SSM) for exchange of operational commands and telemetry data. SADE operates and controls the Solar Array Drive Mechanisms (SADM) for the orientation of the Solar Array Drive (SAD). It also monitors the position of the arrays and the temperature of the SADM. During the first HST servicing mission, the astronauts replaced the SADE component because of some malfunctions. This turned out to be a very challenging extravehicular activity (EVA). Two transistors and two diodes had been thermally stressed with the conformal coating discolored and charred. Soldered cornections became molten and reflowed between the two diodes. The failed transistors gave no indication of defective construction. All repairs were made and the HST was redeposited into orbit. Prior to undertaking this challenging mission, the orbiter's crew trained at Marshall Space Flight Center's (MSFC) Neutral Buoyancy Simulator (NBS) to prepare themselves for working in a low gravity environment. They also practiced replacing HST parts and exercised maneuverability and equipment handling. Pictured is an astronaut practicing climbing a space platform that was necessary in making repairs on the HST.

Neutral Buoyancy Simulator - SADE NBS Test

NASA Technical Reports Server (NTRS)

1983-01-01

One of the main components of the Hubble Space Telescope (HST) is the Solar Array Drive Electronics (SADE) system. This system interfaces with the Support System Module (SSM) for exchange of operational commands and telemetry data. SADE operates and controls the Solar Array Drive Mechanisms (SADM) for the orientation of the Solar Array Drive (SAD). It also monitors the position of the arrays and the temperature of the SADM. During the first HST servicing mission, the astronauts replaced the SADE component because of some malfunctions. This turned out to be a very challenging extravehicular activity (EVA). Two transistors and two diodes had been thermally stressed with the conformal coating discolored and charred. Soldered cornections became molten and reflowed between the two diodes. The failed transistors gave no indication of defective construction. All repairs were made and the HST was redeposited into orbit. Prior to undertaking this challenging mission, the orbiter's crew trained at Marshall Space Flight Center's (MSFC) Neutral Buoyancy Simulator (NBS) to prepare themselves for working in a low gravity environment. They also practiced replacing HST parts and exercised maneuverability and equipment handling. Pictured is an astronaut practicing climbing a space platform that was necessary in making repairs on the HST.