Cabled-observatory Regional Circulation Moorings on the Endeavour segment of the Juan de Fuca Ridge

NASA Astrophysics Data System (ADS)

Mihaly, S. F.

2011-12-01

In September of 2010, one of four moorings was deployed on the Endeavour node of the NEPTUNE Canada cabled-observatory network. The installation included the laying of a 7km cable from the node to the mooring site in the axial valley about 3km north of the Main Endeavour Vent Field over extraordinary bathymetry. This September, three more cables and secondary junction boxes will be deployed to support the three additional moorings that complete the regional circulation array. The cable-laying is facilitated by the Canadian Scientific Submersible Facility's ROV ROPOS and a remotely operated cable-laying system, whereas the actual deployment of the moorings is a two ship operation. The CCGS John P. Tully lowers the mooring anchor first, while the RV Thomas G. Thompson supports the ROV operations which navigate the mooring to underwater mateable cable end. Precise navigation is needed because there are few areas suitable for placement of the junction boxes. Scientifically, the moorings are designed and located to best constrain the hydrothermally driven circulation within the rift valley, the regional circulation can then be used as a proxy measurement for hydrothermal fluxes. Each mooring carries a current meter/ ctd pair at 4, 50, 125, and 200m, with an upward looking ADCP at 250m. The northern moorings are located between the Hi-Rise and Salty Dawg fields about 700m apart in the ~1km wide rift valley and the southern moorings are located south of the Mothra vent field. Here we present initial results from the four mooring array.

Catamaran or semi-submersible for floating platform - selection of a better design

NASA Astrophysics Data System (ADS)

Qasim, Idrees; Gao, Liangtian; Peng, Duojin; Liu, Bo

2018-02-01

With nonstop advancement in marine engineering, more and more new structures are being designed and explored for tidal current energy. There are three different kinds of support structures for tidal current power station mostly in use, which are sea-bed mounted/gravity based system, pile mounted system and floating moored platform. Comparing all of them, the floating mooring system is most suitable for deep water systems and the application of this arrangement is widely usable. In this paper, a semi-submersible and a catamaran as floating platforms for tidal current power stations are studied are compared on the basis of its economics, efficiency of turbine and stability of the station. Based on basic ship theory and using software MAXSURF, the stability of Catamaran tidal current power station is also calculated. It is found that the catamaran design is optimal choice.

Long Term Upper Ocean Study (LOTUS). A Summary of the Historical Data and Engineering Test Data.

DTIC Science & Technology

1982-12-01

the temperature measurements is .1% of the temperature range or .0250C. The recording units were held in stainless steel brackets with strength... diagram of mooring No. 693. 105 A2. Mooring diagram of mooring No. 694. 106 A3. Mooring diagram of mooring No. 733. 107 Acknowledgements The engineering...33059.8’N, 7000.1’W. Mooring diagrams appear in figures A-1 and A-2. The surface mooring, designated LOTUS-i, had a buoy with an Aanderaa meteorological

Moore's law and the impact on trusted and radiation-hardened microelectronics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ma, Kwok Kee

2011-12-01

In 1965 Gordon Moore wrote an article claiming that integrated circuit density would scale exponentially. His prediction has remained valid for more than four decades. Integrated circuits have changed all aspects of everyday life. They are also the 'heart and soul' of modern systems for defense, national infrastructure, and intelligence applications. The United States government needs an assured and trusted microelectronics supply for military systems. However, migration of microelectronics design and manufacturing from the United States to other countries in recent years has placed the supply of trusted microelectronics in jeopardy. Prevailing wisdom dictates that it is necessary to usemore » microelectronics fabricated in a state-of-the-art technology for highest performance and military system superiority. Close examination of silicon microelectronics technology evolution and Moore's Law reveals that this prevailing wisdom is not necessarily true. This presents the US government the possibility of a totally new approach to acquire trusted microelectronics.« less

Physical oceanographic data from the OTEC Punta Tuna, Puerto Rico Site, September 1979-June 1980

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frye, D.; Davison, A.; Leavitt, K.

1981-01-01

The first results of an oceanographic measurement program being conducted off the southeast corner of Puerto Rico are presented. The study site is a proposed OTEC site and is located about 20 km off Punta Tuna. The objectives of the measurement program are to document the physical oceanography of the site as related to the engineering and environmental factors involved in OTEC design and operation. Oceanographic measurements include: (1) a subsurface mooring instrumented with five current, temperature, and pressure recorders; and (2) quarterly hydrographic cruises to measure salinity, temperature, and depth profiles on a grid of 33 stations in themore » vicinity of the mooring site. The first cruise, conducted between 16 and 21 June 1980, included the initial mooring deployment and a CTD (conductivity, temperature, and depth) and XBT (expendable bathythermograph) survey. The CTD/XBT measurements are presented. Also included are results of in situ current, temperature, and pressure measurements made during two previous programs. In September 1979, Coastal Marine Research (CMR) deployed a mooring at approximately the same site as the present mooring. Results from three of these instruments are included. The Naval Underwater Systems Center deployed a mooring at this site in February 1979 and partial results from one instrument on this mooring are also presented. (WHK)« less

A revolutionary and operational tethered aerostat system illustrating new LTA technology. [for ground-air-ground communications

NASA Technical Reports Server (NTRS)

Menke, J. A.

1975-01-01

An operational tethered aerostat system, which demonstrates utility of LTA systems, is described. It was made possible by development of a reliable tethered aerostat that is used to support broadcast equipment at an altitude of 10,000 feet. Two elements of the TCOM system, the aerostat and mooring station, are particularly relevant to the LTA Workshop. They demonstrate the feasibility of using LTA vehicles in real, operational, all-weather applications and, in addition, illustrate an advance in the overall technology base of LTA. The aerostat and the mooring station, including their technical design features and demonstrated performance characteristics, are described.

Technology-design-manufacturing co-optimization for advanced mobile SoCs

NASA Astrophysics Data System (ADS)

Yang, Da; Gan, Chock; Chidambaram, P. R.; Nallapadi, Giri; Zhu, John; Song, S. C.; Xu, Jeff; Yeap, Geoffrey

2014-03-01

How to maintain the Moore's Law scaling beyond the 193 immersion resolution limit is the key question semiconductor industry needs to answer in the near future. Process complexity will undoubtfully increase for 14nm node and beyond, which brings both challenges and opportunities for technology development. A vertically integrated design-technologymanufacturing co-optimization flow is desired to better address the complicated issues new process changes bring. In recent years smart mobile wireless devices have been the fastest growing consumer electronics market. Advanced mobile devices such as smartphones are complex systems with the overriding objective of providing the best userexperience value by harnessing all the technology innovations. Most critical system drivers are better system performance/power efficiency, cost effectiveness, and smaller form factors, which, in turns, drive the need of system design and solution with More-than-Moore innovations. Mobile system-on-chips (SoCs) has become the leading driver for semiconductor technology definition and manufacturing. Here we highlight how the co-optimization strategy influenced architecture, device/circuit, process technology and package, in the face of growing process cost/complexity and variability as well as design rule restrictions.

Implementation of Distributed Services for a Deep Sea Moored Instrument Network

NASA Astrophysics Data System (ADS)

Oreilly, T. C.; Headley, K. L.; Risi, M.; Davis, D.; Edgington, D. R.; Salamy, K. A.; Chaffey, M.

2004-12-01

The Monterey Ocean Observing System (MOOS) is a moored observatory network consisting of interconnected instrument nodes on the sea surface, midwater, and deep sea floor. We describe Software Infrastructure and Applications for MOOS ("SIAM"), which implement the management, control, and data acquisition infrastructure for the moored observatory. Links in the MOOS network include fiber-optic and 10-BaseT copper connections between the at-sea nodes. A Globalstar satellite transceiver or 900 MHz Freewave terrestrial line-of-sight RF modem provides the link to shore. All of these links support Internet protocols, providing TCP/IP connectivity throughout a system that extends from shore to sensor nodes at the air-sea interface, through the oceanic water column to a benthic network of sensor nodes extending across the deep sea floor. Exploiting this TCP/IP infrastructure as well as capabilities provided by MBARI's MOOS mooring controller, we use powerful Internet software technologies to implement a distributed management, control and data acquisition system for the moored observatory. The system design meets the demanding functional requirements specified for MOOS. Nodes and their instruments are represented by Java RMI "services" having well defined software interfaces. Clients anywhere on the network can interact with any node or instrument through its corresponding service. A client may be on the same node as the service, may be on another node, or may reside on shore. Clients may be human, e.g. when a scientist on shore accesses a deployed instrument in real-time through a user interface. Clients may also be software components that interact autonomously with instruments and nodes, e.g. for purposes such as system resource management or autonomous detection and response to scientifically interesting events. All electrical power to the moored network is provided by solar and wind energy, and the RF shore-to-mooring links are intermittent and relatively low-bandwidth connections. Thus power and wireless bandwidth are limited resources that constrain our choice of service technologies and wireless access strategy. We describe and evaluate system performance in light of actual deployment of observatory elements in Monterey Bay, and discuss how the system can be developed further. We also consider management and control strategies for the cable-to-shore observatory known as MARS ("Monterey Accelerated Research System"). The MARS cable will provide high power and continuous high-bandwidth connectivity between seafloor instrument nodes and shore, thus removing key limitations of the moored observatory. Moreover MARS functional requirements may differ significantly from MOOS requirements. In light of these differences, we discuss how elements of our MOOS moored observatory architecture might be adapted to MARS.

An experimental study of the effect of mooring systems on the dynamics of a SPAR buoy-type floating offshore wind turbine

NASA Astrophysics Data System (ADS)

Hong, Sinpyo; Lee, Inwon; Park, Seong Hyeon; Lee, Cheolmin; Chun, Ho-Hwan; Lim, Hee Chang

2015-09-01

An experimental study of the effect of mooring systems on the dynamics of a SPAR buoy-type floating offshore wind turbine is presented. The effects of the Center of Gravity (COG), mooring line spring constant, and fair-lead location on the turbine's motion in response to regular waves are investigated. Experimental results show that for a typical mooring system of a SPAR buoy-type Floating Offshore Wind Turbine (FOWT), the effect of mooring systems on the dynamics of the turbine can be considered negligible. However, the pitch decreases notably as the COG increases. The COG and spring constant of the mooring line have a negligible effect on the fairlead displacement. Numerical simulation and sensitivity analysis show that the wind turbine motion and its sensitivity to changes in the mooring system and COG are very large near resonant frequencies. The test results can be used to validate numerical simulation tools for FOWTs.

Computing the Moore-Penrose Inverse of a Matrix with a Computer Algebra System

ERIC Educational Resources Information Center

Schmidt, Karsten

2008-01-01

In this paper "Derive" functions are provided for the computation of the Moore-Penrose inverse of a matrix, as well as for solving systems of linear equations by means of the Moore-Penrose inverse. Making it possible to compute the Moore-Penrose inverse easily with one of the most commonly used Computer Algebra Systems--and to have the blueprint…

PMEL Contributions to the OceanSITES Program

DTIC Science & Technology

2006-09-01

System and international research programs. PMEL is a major contribu- tor to OceanSITES in the context of the Tropical Ocean At- mosphere/ Triangle ...include five TAO moorings, the KEO mooring, and non- PMEL moorings off of Hawaii and Bermuda (Fig. 1, Table 3). The prototype for the moored CO2 system was

The DMON2: A Commercially Available Broadband Acoustic Monitoring Instrument

DTIC Science & Technology

2015-09-30

the need for a new system design. o Seamless integration of the DMON2 with multiple platforms: Slocum and Wave Gliders, moored real-time buoys and...and robustness (stainless steel design). Transducer Head Printed Circuit Board (PCB): We have completed the design and fabrication of the DMON2

Two mooring dolphin concept for exposed tanker terminals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Khanna, J.; Birt, C.

1978-02-01

The conventional design of a tanker terminal provides for two or more mooring dolphins on each side of the breasting dolphins. Head and stern lines are attached to the outer mooring dolphins and breast lines to the inner mooring dolphins. In exposed locations, the expense of construction may be significantly reduced if a way can be found to reduce the number of mooring dolphins required for the safe mooring of ships at a fixed berth. A study based on plans for a proposed terminal for tankers from 25,000 to 100,000 dwt in the Bay of Fundy in eastern Canada considersmore » the possibility of reducing the total number of mooring dolphins from four to two. Results of a static analysis of mooring loads due to wind and current and a hydraulic model test for mooring loads due to waves are presented.« less

Verification and Validation of Multisegmented Mooring Capabilities in FAST v8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersen, Morten T.; Wendt, Fabian F.; Robertson, Amy N.

2016-07-01

The quasi-static and dynamic mooring modules of the open-source aero-hydro-servo-elastic wind turbine simulation software, FAST v8, have previously been verified and validated, but only for mooring arrangements consisting of single lines connecting each fairlead and anchor. This paper extends the previous verification and validation efforts to focus on the multisegmented mooring capability of the FAST v8 modules: MAP++, MoorDyn, and the OrcaFlex interface. The OC3-Hywind spar buoy system tested by the DeepCwind consortium at the MARIN ocean basin, which includes a multisegmented bridle layout of the mooring system, was used for the verification and validation activities.

Mooring line damping estimation for a floating wind turbine.

PubMed

Qiao, Dongsheng; Ou, Jinping

2014-01-01

The dynamic responses of mooring line serve important functions in the station keeping of a floating wind turbine (FWT). Mooring line damping significantly influences the global motions of a FWT. This study investigates the estimation of mooring line damping on the basis of the National Renewable Energy Laboratory 5 MW offshore wind turbine model that is mounted on the ITI Energy barge. A numerical estimation method is derived from the energy absorption of a mooring line resulting from FWT motion. The method is validated by performing a 1/80 scale model test. Different parameter changes are analyzed for mooring line damping induced by horizontal and vertical motions. These parameters include excitation amplitude, excitation period, and drag coefficient. Results suggest that mooring line damping must be carefully considered in the FWT design.

Mooring Line Damping Estimation for a Floating Wind Turbine

PubMed Central

Qiao, Dongsheng; Ou, Jinping

2014-01-01

The dynamic responses of mooring line serve important functions in the station keeping of a floating wind turbine (FWT). Mooring line damping significantly influences the global motions of a FWT. This study investigates the estimation of mooring line damping on the basis of the National Renewable Energy Laboratory 5 MW offshore wind turbine model that is mounted on the ITI Energy barge. A numerical estimation method is derived from the energy absorption of a mooring line resulting from FWT motion. The method is validated by performing a 1/80 scale model test. Different parameter changes are analyzed for mooring line damping induced by horizontal and vertical motions. These parameters include excitation amplitude, excitation period, and drag coefficient. Results suggest that mooring line damping must be carefully considered in the FWT design. PMID:25243231

A comparison of the impact of 'seagrass-friendly' boat mooring systems on Posidonia australis.

PubMed

Demers, Marie-Claire A; Davis, Andrew R; Knott, Nathan A

2013-02-01

Permanent boat moorings have contributed to the decline of seagrasses worldwide, prompting the development of 'seagrass-friendly' moorings. We contrasted seagrass cover and density (predominantly Posidonia australis) in the vicinity of three mooring types and nearby reference areas lacking moorings in Jervis Bay, Australia. We examined two types of 'seagrass-friendly' mooring and a conventional 'swing' mooring. 'Swing' moorings produced significant seagrass scour, denuding patches of ~9 m radius. Seagrass-friendly 'cyclone' moorings produced extensive denuded patches (average radius of ~18 m). Seagrass-friendly 'screw' moorings, conversely, had similar seagrass cover to nearby reference areas. Our findings reinforce previous work highlighting the negative effects of 'swing' and 'cyclone' moorings. In contrast, the previously unstudied 'screw' moorings were highly effective. We conclude that regular maintenance of moorings and the monitoring of surrounding seagrass are required to ensure that 'seagrass-friendly' moorings are operating effectively. This is important, as following damage Posidonia will take many decades to recover. Copyright © 2012 Elsevier Ltd. All rights reserved.

46 CFR 121.300 - Ground tackle and mooring lines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Ground tackle and mooring lines. 121.300 Section 121.300... MISCELLANEOUS SYSTEMS AND EQUIPMENT Mooring and Towing Equipment § 121.300 Ground tackle and mooring lines. A vessel must be fitted with ground tackle and mooring lines necessary for the vessel to be safely anchored...

46 CFR 121.300 - Ground tackle and mooring lines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Ground tackle and mooring lines. 121.300 Section 121.300... MISCELLANEOUS SYSTEMS AND EQUIPMENT Mooring and Towing Equipment § 121.300 Ground tackle and mooring lines. A vessel must be fitted with ground tackle and mooring lines necessary for the vessel to be safely anchored...

Verification and Validation of Multisegmented Mooring Capabilities in FAST v8: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Andersen, Morten T.; Wendt, Fabian; Robertson, Amy

2016-08-01

The quasi-static and dynamic mooring modules of the open-source aero-hydro-servo-elastic wind turbine simulation software, FAST v8, have previously been verified and validated, but only for mooring arrangements consisting of single lines connecting each fairlead and anchor. This paper extends the previous verification and validation efforts to focus on the multisegmented mooring capability of the FAST v8 modules: MAP++, MoorDyn, and the OrcaFlex interface. The OC3-Hywind spar buoy system tested by the DeepCwind consortium at the MARIN ocean basin, which includes a multisegmented bridle layout of the mooring system, was used for the verification and validation activities.

33 CFR 62.35 - Mooring buoys.

Code of Federal Regulations, 2013 CFR

2013-07-01

....35 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.35 Mooring buoys. Mooring... identification and to avoid confusion with aids to navigation. ...

33 CFR 62.35 - Mooring buoys.

Code of Federal Regulations, 2014 CFR

2014-07-01

....35 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.35 Mooring buoys. Mooring... identification and to avoid confusion with aids to navigation. ...

33 CFR 62.35 - Mooring buoys.

Code of Federal Regulations, 2011 CFR

2011-07-01

....35 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.35 Mooring buoys. Mooring... identification and to avoid confusion with aids to navigation. ...

33 CFR 62.35 - Mooring buoys.

Code of Federal Regulations, 2012 CFR

2012-07-01

....35 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.35 Mooring buoys. Mooring... identification and to avoid confusion with aids to navigation. ...

33 CFR 62.35 - Mooring buoys.

Code of Federal Regulations, 2010 CFR

2010-07-01

....35 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION UNITED STATES AIDS TO NAVIGATION SYSTEM The U.S. Aids to Navigation System § 62.35 Mooring buoys. Mooring... identification and to avoid confusion with aids to navigation. ...

The future of EUV lithography: enabling Moore's Law in the next decade

NASA Astrophysics Data System (ADS)

Pirati, Alberto; van Schoot, Jan; Troost, Kars; van Ballegoij, Rob; Krabbendam, Peter; Stoeldraijer, Judon; Loopstra, Erik; Benschop, Jos; Finders, Jo; Meiling, Hans; van Setten, Eelco; Mika, Niclas; Dredonx, Jeannot; Stamm, Uwe; Kneer, Bernhard; Thuering, Bernd; Kaiser, Winfried; Heil, Tilmann; Migura, Sascha

2017-03-01

While EUV systems equipped with a 0.33 Numerical Aperture lenses are readying to start volume manufacturing, ASML and Zeiss are ramping up their development activities on a EUV exposure tool with Numerical Aperture greater than 0.5. The purpose of this scanner, targeting a resolution of 8nm, is to extend Moore's law throughout the next decade. A novel, anamorphic lens design, has been developed to provide the required Numerical Aperture; this lens will be paired with new, faster stages and more accurate sensors enabling Moore's law economical requirements, as well as the tight focus and overlay control needed for future process nodes. The tighter focus and overlay control budgets, as well as the anamorphic optics, will drive innovations in the imaging and OPC modelling, and possibly in the metrology concepts. Furthermore, advances in resist and mask technology will be required to image lithography features with less than 10nm resolution. This paper presents an overview of the key technology innovations and infrastructure requirements for the next generation EUV systems.

Probabilistic analysis and fatigue damage assessment of offshore mooring system due to non-Gaussian bimodal tension processes

NASA Astrophysics Data System (ADS)

Chang, Anteng; Li, Huajun; Wang, Shuqing; Du, Junfeng

2017-08-01

Both wave-frequency (WF) and low-frequency (LF) components of mooring tension are in principle non-Gaussian due to nonlinearities in the dynamic system. This paper conducts a comprehensive investigation of applicable probability density functions (PDFs) of mooring tension amplitudes used to assess mooring-line fatigue damage via the spectral method. Short-term statistical characteristics of mooring-line tension responses are firstly investigated, in which the discrepancy arising from Gaussian approximation is revealed by comparing kurtosis and skewness coefficients. Several distribution functions based on present analytical spectral methods are selected to express the statistical distribution of the mooring-line tension amplitudes. Results indicate that the Gamma-type distribution and a linear combination of Dirlik and Tovo-Benasciutti formulas are suitable for separate WF and LF mooring tension components. A novel parametric method based on nonlinear transformations and stochastic optimization is then proposed to increase the effectiveness of mooring-line fatigue assessment due to non-Gaussian bimodal tension responses. Using time domain simulation as a benchmark, its accuracy is further validated using a numerical case study of a moored semi-submersible platform.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jens Korsgaard

The main conclusions from the work carried out under this contract are: An ordinary seafarer can learn by training on a simulator, to moor large tanker vessels to the Hydrostatic Mooring, safely and quickly, in all weather conditions up to storms generating waves with a significant wave height of 8 m. Complete conceptual design of the Hydrostatic Mooring buoy was carried out which proved that the buoy could be constructed entirely from commercially available standard components and materials. The design is robust, and damage resistant. The mooring tests had a 100% success rate from the point of view of themore » buoy being securely attached and moored to the vessel following every mooring attempt. The tests had an 80% success rate from the point of view of the buoy being adequately centered such that petroleum transfer equipment on the vessel could be attached to the corresponding equipment on the buoy. The results given in Table 3-2 of the mooring tests show a consistently improving performance from test to test by the Captain that performed the mooring operations. This is not surprising, in view of the fact that the Captain had only three days of training on the simulator prior to conducting the tests, that the maneuvering required is non-standard, and the test program itself lasted four days. One conclusion of the test performance is that the Captain was not fully trained at the initiation of the test. It may therefore be concluded that a thoroughly trained navigator would probably be able to make the mooring such that the fluid transfer equipment can be connected with reliability in excess of 90%. Considering that the typical standard buoy has enough power aboard to make eight mooring attempts, this implies that the probability that the mooring attempt should fail because of the inability to connect the fluid transfer equipment is of the order of 10{sup {minus}8}. It may therefore be concluded that the mooring operation between a Hydrostatic Mooring and a large tanker vessel can be carried out with near absolute reliability in all sea states up to a sea state where the significant wave height is 8 m.« less

A Different Perspective of the Teaching Philosophy of RL Moore

ERIC Educational Resources Information Center

Jones, Stephen L.

2017-01-01

Dr RL Moore was undoubtedly one of the finest mathematics teachers ever. He developed a unique teaching method designed to teach his students to think like mathematicians. His method was not designed to convey any particular mathematical knowledge. Instead, it was designed to teach his students to think. Today, his method has been modified to…

Selection and optimization of mooring cables on floating platform for special purposes

NASA Astrophysics Data System (ADS)

Ma, Guang-ying; Yao, Yun-long; Zhao, Chen-yao

2017-08-01

This paper studied a new type of assembled marine floating platform for special purposes. The selection and optimization of mooring cables on the floating platform are studied. By using ANSYS AQWA software, the hydrodynamic model of the platform was established to calculate the time history response of the platform motion under complex water environments, such as wind, wave, current and mooring. On this basis, motion response and cable tension were calculated with different cable mooring states under the designed environmental load. Finally, the best mooring scheme to meet the cable strength requirements was proposed, which can lower the motion amplitude of the platform effectively.

Oscillation Responses to an Extreme Weather Event from a Deep Moored Observing System

NASA Astrophysics Data System (ADS)

Wang, Z.; Dimarco, S. F.; Stoessel, M. M.; Zhang, X.; Ingle, S.

2011-12-01

In June 2007 tropical Cyclone Gonu passed directly over an ocean observing system consisting of four, deep autonomous mooring stations along the 3000 m isobath in the northern Arabian Sea. Gonu was the largest cyclone known to have occurred in the Arabian Sea or to strike the Arabian Peninsula. The mooring system was designed by Lighthouse R & D Enterprises, Inc. and installed in cooperation with the Oman Ministry of Agriculture and Fisheries Wealth. The instruments on the moorings continuously recorded water velocities, temperature, conductivity, pressure, dissolved oxygen and turbidity at multiple depths and at hourly intervals during the storm. Near-inertial oscillations at all moorings from thermocline to seafloor are coincident with the arrival of Gonu. Sub-inertial oscillations with periods of 2-10 days are recorded at the post-storm relaxation stage of Gonu, primarily in the thermocline. These oscillations consist of warm, saline water masses, likely originating from the Persian Gulf. Prominent 12.7-day sub-inertial waves, measured at a station ~300 km offshore, are bottom-intensified and have characteristics of baroclinic, topographically-trapped waves. Theoretical results from a topographically-trapped wave model are in a good agreement with the observed 12.7-day waves. The wavelength of the 12.7-day waves is about 590 km calculated from the dispersion relationship. Further analysis suggests that a resonant standing wave is responsible for trapping the 12.7-day wave energy inside the Sea of Oman basin. The observational results reported here are the first measurements of deepwater responses to a tropical cyclone in the Sea of Oman/Arabian Sea. Our study demonstrates the utility of sustained monitoring for studying the impact of extreme weather events on the ocean.

33 CFR 165.T14-204 - Safety Zone; fixed mooring balls, south of Barbers Pt Harbor Channel, Oahu, Hawaii.

Code of Federal Regulations, 2010 CFR

2010-07-01

... contained within a 400-yard radius (366-meter) radius around position 21°18′35.00″ N., 158°07′33.00″ W. This... mooring balls will be placed 133 yards (121 meters) in a circular design for preapproved vessel mooring...

Moore's curve structuring of ferromagnetic composite PE-NiFe absorbers

NASA Astrophysics Data System (ADS)

Fernez, N.; Arbaoui, Y.; Maalouf, A.; Chevalier, A.; Agaciak, P.; Burgnies, L.; Queffelec, P.; Laur, V.; Lheurette, É.

2018-02-01

A ferromagnetic material involving nickel-iron particles embedded in a polyethylene matrix is synthesized and electrically characterized between 1 and 12 GHz. These measurements show the combination of electric and magnetic activity along with significant loss terms. We take benefit of these properties for the design of broadband electromagnetic absorbers. To this aim, we use a fractal structuring based on Moore curves. The advantage of etching patterns over metallic ones is clearly evidenced, and several pattern absorbers identified by their Moore's order iteration are designed and analyzed under oblique incidence.

46 CFR 121.300 - Ground tackle and mooring lines.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Ground tackle and mooring lines. 121.300 Section 121.300 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE... MISCELLANEOUS SYSTEMS AND EQUIPMENT Mooring and Towing Equipment § 121.300 Ground tackle and mooring lines. A...

The Fram Strait integrated ocean observatory

NASA Astrophysics Data System (ADS)

Fahrbach, E.; Beszczynska-Möller, A.; Rettig, S.; Rohardt, G.; Sagen, H.; Sandven, S.; Hansen, E.

2012-04-01

A long-term oceanographic moored array has been operated since 1997 to measure the ocean water column properties and oceanic advective fluxes through Fram Strait. While the mooring line along 78°50'N is devoted to monitoring variability of the physical environment, the AWI Hausgarten observatory, located north of it, focuses on ecosystem properties and benthic biology. Under the EU DAMOCLES and ACOBAR projects, the oceanographic observatory has been extended towards the innovative integrated observing system, combining the deep ocean moorings, multipurpose acoustic system and a network of gliders. The main aim of this system is long-term environmental monitoring in Fram Strait, combining satellite data, acoustic tomography, oceanographic measurements at moorings and glider sections with high-resolution ice-ocean circulation models through data assimilation. In future perspective, a cable connection between the Hausgarten observatory and a land base on Svalbard is planned as the implementation of the ESONET Arctic node. To take advantage of the planned cabled node, different technologies for the underwater data transmission were reviewed and partially tested under the ESONET DM AOEM. The main focus was to design and evaluate available technical solutions for collecting data from different components of the Fram Strait ocean observing system, and an integration of available data streams for the optimal delivery to the future cabled node. The main components of the Fram Strait integrated observing system will be presented and the current status of available technologies for underwater data transfer will be reviewed. On the long term, an initiative of Helmholtz observatories foresees the interdisciplinary Earth-Observing-System FRAM which combines observatories such as the long term deep-sea ecological observatory HAUSGARTEN, the oceanographic Fram Strait integrated observing system and the Svalbard coastal stations maintained by the Norwegian ARCTOS network. A vision of this modular underwater observatory network in Fram Strait will be presented.

Integration of multi-objective structural optimization into cementless hip prosthesis design: Improved Austin-Moore model.

PubMed

Kharmanda, G

2016-11-01

A new strategy of multi-objective structural optimization is integrated into Austin-Moore prosthesis in order to improve its performance. The new resulting model is so-called Improved Austin-Moore. The topology optimization is considered as a conceptual design stage to sketch several kinds of hollow stems according to the daily loading cases. The shape optimization presents the detailed design stage considering several objectives. Here, A new multiplicative formulation is proposed as a performance scale in order to define the best compromise between several requirements. Numerical applications on 2D and 3D problems are carried out to show the advantages of the proposed model.

48 CFR 252.225-7019 - Restriction on acquisition of anchor and mooring chain.

Code of Federal Regulations, 2012 CFR

2012-10-01

... of anchor and mooring chain. 252.225-7019 Section 252.225-7019 Federal Acquisition Regulations System... and mooring chain. As prescribed in 225.7007-3, use the following clause: Restriction on Acquisition of Anchor and Mooring Chain (DEC 2009)) (a) Definition. “Component,” as used in this clause, means an...

48 CFR 252.225-7019 - Restriction on acquisition of anchor and mooring chain.

Code of Federal Regulations, 2013 CFR

2013-10-01

... of anchor and mooring chain. 252.225-7019 Section 252.225-7019 Federal Acquisition Regulations System... and mooring chain. As prescribed in 225.7007-3, use the following clause: Restriction on Acquisition of Anchor and Mooring Chain (DEC 2009)) (a) Definition. “Component,” as used in this clause, means an...

48 CFR 252.225-7019 - Restriction on acquisition of anchor and mooring chain.

Code of Federal Regulations, 2014 CFR

2014-10-01

... of anchor and mooring chain. 252.225-7019 Section 252.225-7019 Federal Acquisition Regulations System... and mooring chain. As prescribed in 225.7007-3, use the following clause: Restriction on Acquisition of Anchor and Mooring Chain (DEC 2009)) (a) Definition. “Component,” as used in this clause, means an...

48 CFR 252.225-7019 - Restriction on acquisition of anchor and mooring chain.

Code of Federal Regulations, 2011 CFR

2011-10-01

... of anchor and mooring chain. 252.225-7019 Section 252.225-7019 Federal Acquisition Regulations System... and mooring chain. As prescribed in 225.7007-3, use the following clause: Restriction on Acquisition of Anchor and Mooring Chain (DEC 2009)) (a) Definition. “Component,” as used in this clause, means an...

48 CFR 252.225-7019 - Restriction on acquisition of anchor and mooring chain.

Code of Federal Regulations, 2010 CFR

2010-10-01

... of anchor and mooring chain. 252.225-7019 Section 252.225-7019 Federal Acquisition Regulations System... and mooring chain. As prescribed in 225.7007-3, use the following clause: Restriction on Acquisition of Anchor and Mooring Chain (DEC 2009)) (a) Definition. “Component,” as used in this clause, means an...

High-NA EUV lithography enabling Moore's law in the next decade

NASA Astrophysics Data System (ADS)

van Schoot, Jan; Troost, Kars; Bornebroek, Frank; van Ballegoij, Rob; Lok, Sjoerd; Krabbendam, Peter; Stoeldraijer, Judon; Loopstra, Erik; Benschop, Jos P.; Finders, Jo; Meiling, Hans; van Setten, Eelco; Kneer, Bernhard; Kuerz, Peter; Kaiser, Winfried; Heil, Tilmann; Migura, Sascha; Neumann, Jens Timo

2017-10-01

While EUV systems equipped with a 0.33 Numerical Aperture lenses are readying to start volume manufacturing, ASML and Zeiss are ramping up their activities on a EUV exposure tool with Numerical Aperture of 0.55. The purpose of this scanner, targeting an ultimate resolution of 8nm, is to extend Moore's law throughout the next decade. A novel, anamorphic lens design, capable of providing the required Numerical Aperture has been investigated; This lens will be paired with new, faster stages and more accurate sensors enabling Moore's law economical requirements, as well as the tight focus and overlay control needed for future process nodes. The tighter focus and overlay control budgets, as well as the anamorphic optics, will drive innovations in the imaging and OPC modelling. Furthermore, advances in resist and mask technology will be required to image lithography features with less than 10nm resolution. This paper presents an overview of the target specifications, key technology innovations and imaging simulations demonstrating the advantages as compared to 0.33NA and showing the capabilities of the next generation EUV systems.

NREL-Statoil Collaborate to Make the First Multi-Turbine Floating Offshore

Science.gov Websites

investigated four design load cases: power production, power production plus occurrence of fault, parked -thereby lowering the cost of energy by increasing power production. Senu Sirnivas, a principal engineer at design and analysis, turbine size-up scaling, the mooring system, instrumentation, data acquisition, and

Lesson Development for English Learners in Content Area Settings: Key Considerations. Q&A with Sarah Catherine K. Moore, Ph.D. 2016 Educator Effectiveness Webinar Series

ERIC Educational Resources Information Center

Moore, Sarah Catherine K.

2016-01-01

In this webinar, Dr. Sarah Catherine K. Moore, Program Director at the Center for Applied Linguistics, outlined factors for content area teachers to consider as they design and deliver lessons for mainstream classrooms that include English learner (EL) students. This Q&A addressed the questions participants had for Dr. Moore following the…

PREFACE: E-MRS 2012 Spring Meeting, Symposium M: More than Moore: Novel materials approaches for functionalized Silicon based Microelectronics

NASA Astrophysics Data System (ADS)

Wenger, Christian; Fompeyrine, Jean; Vallée, Christophe; Locquet, Jean-Pierre

2012-12-01

More than Moore explores a new area of Silicon based microelectronics, which reaches beyond the boundaries of conventional semiconductor applications. Creating new functionality to semiconductor circuits, More than Moore focuses on motivating new technological possibilities. In the past decades, the main stream of microelectronics progresses was mainly powered by Moore's law, with two focused development arenas, namely, IC miniaturization down to nano scale, and SoC based system integration. While the microelectronics community continues to invent new solutions around the world to keep Moore's law alive, there is increasing momentum for the development of 'More than Moore' technologies which are based on silicon technologies but do not simply scale with Moore's law. Typical examples are RF, Power/HV, Passives, Sensor/Actuator/MEMS or Bio-chips. The More than Moore strategy is driven by the increasing social needs for high level heterogeneous system integration including non-digital functions, the necessity to speed up innovative product creation and to broaden the product portfolio of wafer fabs, and the limiting cost and time factors of advanced SoC development. It is believed that More than Moore will add value to society on top of and beyond advanced CMOS with fast increasing marketing potentials. Important key challenges for the realization of the 'More than Moore' strategy are: perspective materials for future THz devices materials systems for embedded sensors and actuators perspective materials for epitaxial approaches material systems for embedded innovative memory technologies development of new materials with customized characteristics The Hot topics covered by the symposium M (More than Moore: Novel materials approaches for functionalized Silicon based Microelectronics) at E-MRS 2012 Spring Meeting, 14-18 May 2012 have been: development of functional ceramics thin films New dielectric materials for advanced microelectronics bio- and CMOS compatible material systems piezoelectric films and nanostructures Atomic Layer Deposition (ALD) of oxides and nitrides characterization and metrology of very thin oxide layers We would like to take this opportunity to thank the Scientific Committee and Local Committee for bringing together a coherent and high quality Symposium at E-MRS 2012 Spring Meeting. Christian Wenger, Jean Fompeyrine, Christophe Vallée and Jean-Pierre Locquet Organizing Committee of Symposium M September 2012

33 CFR 207.275 - McClellan-Kerr Arkansas River navigation system: use, administration, and navigation.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Vessels arriving at these markers or the mooring cells immediately upstream and downstream of the lock... mooring facilities at the junction of main stem and secondary channels are to provide temporary mooring...

The structure of the microbial communities in low-moor and high-moor peat bogs of Tomsk oblast

NASA Astrophysics Data System (ADS)

Dobrovol'skaya, T. G.; Golovchenko, A. V.; Kukharenko, O. S.; Yakushev, A. V.; Semenova, T. A.; Inisheva, L. A.

2012-03-01

The number, structure, and physical state of the microbial communities in high-moor and low-moor peat bogs were compared. Distinct differences in these characteristics were revealed. The microbial biomass in the high-moor peat exceeded that in the low-moor peat by 2-9 times. Fungi predominated in the high-moor peat, whereas bacteria were the dominant microorganisms in the low-moor peat. The micromycetal complexes of the high-moor peat were characterized by a high portion of dark-colored representatives; the complexes of the low-moor peat were dominated by fast-growing fungi. The species of the Penicillum genus were dominant in the high-moor peat; the species of Trichoderma were abundant in the low-moor peat. In the former, the bacteria were distinguished as minor components; in the latter, they predominated in the saprotrophic bacterial complex. In the high-moor peat, the microorganisms were represented by bacilli, while, in the low-moor peat, by cytophages, myxobacteria, and actinobacteria. The different physiological states of the bacteria in the studied objects reflecting the duration of the lag phase and the readiness of the metabolic system to consume different substrates were demonstrated for the first time. The relationships between the trophic characteristics of bacterial habitats and the capacity of the bacteria to consume substrates were established.

Model Scaling of Hydrokinetic Ocean Renewable Energy Systems

NASA Astrophysics Data System (ADS)

von Ellenrieder, Karl; Valentine, William

2013-11-01

Numerical simulations are performed to validate a non-dimensional dynamic scaling procedure that can be applied to subsurface and deeply moored systems, such as hydrokinetic ocean renewable energy devices. The prototype systems are moored in water 400 m deep and include: subsurface spherical buoys moored in a shear current and excited by waves; an ocean current turbine excited by waves; and a deeply submerged spherical buoy in a shear current excited by strong current fluctuations. The corresponding model systems, which are scaled based on relative water depths of 10 m and 40 m, are also studied. For each case examined, the response of the model system closely matches the scaled response of the corresponding full-sized prototype system. The results suggest that laboratory-scale testing of complete ocean current renewable energy systems moored in a current is possible. This work was supported by the U.S. Southeast National Marine Renewable Energy Center (SNMREC).

Analysis of AISI 304 Tensile Strength as an Anchor Chain of Mooring System

NASA Astrophysics Data System (ADS)

Hamidah, I.; Wati, R.; Hamdani, R. A.

2018-05-01

The background of this research is the use of mild steel (i.e., St37) as anchor chain that works on the corrosive environment of seawater which is possible to decrease its tensile strength. The longer soaked in seawater, the more significant the lowering of its tensile strength. Anchor chain needs to be designed by considering its tensile strength and corrosion resistance, so it’s able to support mooring system well. The primary purpose of this research is obtaining the decreasing of stainless steel 304 (AISI 304) tensile strength which is corroded by seawater as anchor chain of the mooring system. It is also essential to obtain the lifetime of AISI304 and St37 as anchor chain with the same load, the corrosion rate of AISI 304, and St 37 in seawater. The method which was employed in this research is an experiment with four pieces of stainless steel AISI 304, and of St 37 corrosion testing samples, six pieces of stainless steel 304, and six pieces of St 37 for tensile testing samples. The result of this research shows that seawater caused stainless steel AISI 304 as anchor chain has decreased of tensile strength about 1.68 % during four weeks. Also, it indicates that AISI 304 as anchor chain has a lifetime about 130 times longer than St 37. Further, we found that the corrosion rate of stainless steel 304 in seawater is 0.2042 mpy in outstanding category, while the St 37 samples reached up to 27.0247 mpy ranked as fair category. This result recommends that AISI 304 more excellence than St 37 as anchor chain of the mooring system.

Solar Sea Power Plants (SSPP): A critical review and survey

NASA Technical Reports Server (NTRS)

Strauss, A. M.

1974-01-01

An overview of technical and economic matters relating to the eventual success or failure of the SSPP concept is presented, with emphasis on the pollution and energy problems which the SSPP would serve to eliminate. Factors discussed include cost, mariculture possibilities, siting, legal limitations, design materials, mooring and anchoring, and the human element involved. Several alternative power systems are considered for incorporation into SSPP design, such as Nitinol power, Claude cycle, and closed cycle engine systems.

Impact analysis of air gap motion with respect to parameters of mooring system for floating platform

NASA Astrophysics Data System (ADS)

Shen, Zhong-xiang; Huo, Fa-li; Nie, Yan; Liu, Yin-dong

2017-04-01

In this paper, the impact analysis of air gap concerning the parameters of mooring system for the semi-submersible platform is conducted. It is challenging to simulate the wave, current and wind loads of a platform based on a model test simultaneously. Furthermore, the dynamic equivalence between the truncated and full-depth mooring system is still a tuff work. However, the wind and current loads can be tested accurately in wind tunnel model. Furthermore, the wave can be simulated accurately in wave tank test. The full-scale mooring system and the all environment loads can be simulated accurately by using the numerical model based on the model tests simultaneously. In this paper, the air gap response of a floating platform is calculated based on the results of tunnel test and wave tank. Meanwhile, full-scale mooring system, the wind, wave and current load can be considered simultaneously. In addition, a numerical model of the platform is tuned and validated by ANSYS AQWA according to the model test results. With the support of the tuned numerical model, seventeen simulation cases about the presented platform are considered to study the wave, wind, and current loads simultaneously. Then, the impact analysis studies of air gap motion regarding the length, elasticity, and type of the mooring line are performed in the time domain under the beam wave, head wave, and oblique wave conditions.

The Moored Acoustic Buoy System (MABS)

DTIC Science & Technology

1975-04-04

STAQOG, Ocean Sciences & Technology Department Indirect. REVIEWED AND APPROY 4 April lq75 A)R. Hse Associate Director for Sonar Retsearch The authors...It consists of a subsurface instrumentation buoy in conjunction with a family of lightweight hydrophone arrays designed to measure a variety of...vertical to horizontal in the water column. Recent de- velopments in lightweight synthetic-cable technology have been incorporated into the design to make

46 CFR 184.300 - Ground tackle and mooring lines.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 7 2014-10-01 2014-10-01 false Ground tackle and mooring lines. 184.300 Section 184.300 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) VESSEL CONTROL AND MISCELLANEOUS SYSTEMS AND EQUIPMENT Mooring and Towing Equipment § 184.300...

Report to the U.S. Congress on the National Oceanographic Partnership Program

DTIC Science & Technology

1999-01-01

security, advancing economic development, protecting quality of life, and strengthening science education and communication through improved knowledge of... nitrate analyzers, and spectral optical sensors) will be tested on testbed moorings near Bermuda and Monterey Bay. The newly developed systems...design, systems integration, interdisciplinary multiscale data assimilation and interactive processes. real-time demonstration of concept and analysis of

COMPETING IN THE SOCIAL BATTLESPACE: INFLUENCING THE THREE DOMAINS

DTIC Science & Technology

2017-06-01

Legacy (Knopf Doubleday Publishing Group, 2009), 33. 39 Norman Polmar and Kenneth J. Moore, Cold War Submarines: The Design and Construction of U.S...and shot Brown six times in the back, killing him. Michael Brown would lay four hours on the pavement as additional police officers and...Cornell University Press. Polmar, Norman, and Kenneth J. Moore. Cold War Submarines: The Design and Construction of U.S. and Soviet Submarines

Study on global performances and mooring-induced damping of a semi-submersible

NASA Astrophysics Data System (ADS)

Xiong, Ling-zhi; Yang, Jian-min; Lv, Hai-ning; Zhao, Wen-hua; Kou, Yu-feng

2016-10-01

The harsh environmental conditions bring strong nonlinearities to the hydrodynamic performances of the offshore floating platforms, which challenge the reliable prediction of the platform coupled with the mooring system. The present study investigates a typical semi-submersible under both the operational and the survival conditions through numerical and experimental methods. The motion responses, the mooring line tensions, and the wave loads on the longitudinal mid-section are investigated by both the fully non-linearly coupled numerical simulation and the physical experiment. Particularly, in the physical model test, the wave loads distributed on the semi-submersible's mid-section were measured by dividing the model into two parts, namely the port and the starboard parts, which were rigidly connected by three six-component force transducers. It is concluded that both the numerical and physical model can have good prediction of the semi-submersible's global responses. In addition, an improved numerical approach is proposed for the estimation of the mooring-induced damping, and is validated by both the experimental and the published results. The characteristics of the mooring-induced damping are further summarized in various sea states, including the operational and the survival environments. In order to obtain the better prediction of the system response in deep water, the mooring-induced damping of the truncated mooring lines applied in the physical experiment are compensated by comparing with those in full length. Furthermore, the upstream taut and the downstream slack mooring lines are classified and investigated to obtain the different mooring line damping performances in the comparative study.

The Wave Glider°: A New Autonomous Surface Vehicle to Augment MBARI's Growing Fleet of Ocean Observing Systems

NASA Astrophysics Data System (ADS)

Tougher, B. B.

2011-12-01

Monterey Bay Aquarium Research Institute's (MBARI) evolving fleet of ocean observing systems has made it possible to collect information and data about a wide variety of ocean parameters, enabling researchers to better understand marine ecosystems. In collaboration with Liquid Robotics Inc, the designer of the Wave Glider autonomous surface vehicle (ASV), MBARI is adding a new capability to its suite of ocean observing tools. This new technology will augment MBARI research programs that use satellites, ships, moorings, drifters, autonomous underwater vehicles (AUVs) and remotely operated vehicles (ROVs) to improve data collection of temporally and spatially variable oceanographic features. The Wave Glider ASV derives its propulsion from wave energy, while sensors and communications are powered through the use of two solar panels and batteries, enabling it to remain at sea indefinitely. Wave Gliders are remotely controlled via real-time Iridium burst communications, which also permit real-time data telemetry. MBARI has developed Ocean Acidification (OA) moorings to continuously monitor the chemical and physical changes occurring in the ocean as a result of increased levels of atmospheric carbon dioxide (CO2). The moorings are spatially restricted by being anchored to the seafloor, so during the summer of 2011 the ocean acidification sensor suite designed for moorings was integrated into a Wave Glider ASV to increase both temporal and spatial ocean observation capabilities. The OA sensor package enables the measurement of parameters essential to better understanding the changing acidity of the ocean, specifically pCO2, pH, oxygen, salinity and temperature. The Wave Glider will also be equipped with a meteorological sensor suite that will measure air temperature, air pressure, and wind speed and direction. The OA sensor integration into a Wave Glider was part of MBARI's 2011 summer internship program. This project involved designing a new layout for the OA sensors within a Wave Glider aft payload dry box. The Wave Glider OA sensor suite includes the addition of a pCO2 standard tank not included within the current OA moorings. Communication links between MBARI electronics and Liquid Robotics Control and Communications were successfully established in the laboratory, however further steps to fully integrate and test the OA system into a Wave Glider ASV are still needed. In the future these ASVs will provide platforms for additional surface and subsurface instrumentation, particularly with MBARI's upcoming Controlled, Agile, and Novel, Observing Network (CANON) projects. The integration of the OA sensor package into a Wave Glider ASV will make it possible to continuously monitor the marine environment during adverse weather conditions which are often difficult to document but scientifically important.

A Portable Parallel Implementation of the U.S. Navy Layered Ocean Model

DTIC Science & Technology

1995-01-01

Wallcraft, PhD (I.C. 1981) Planning Systems Inc. & P. R. Moore, PhD (Camb. 1971) IC Dept. Math. DR Moore 1° Encontro de Metodos Numericos...Kendall Square, Hypercube, D R Moore 1 ° Encontro de Metodos Numericos para Equacöes de Derivadas Parciais A. J. Wallcraft IC Mathematics...chips: Chips Machine DEC Alpha CrayT3D/E SUN Sparc Fujitsu AP1000 Intel 860 Paragon D R Moore 1° Encontro de Metodos Numericos para Equacöes

Technology update: Tethered aerostat structural design and material developments

NASA Technical Reports Server (NTRS)

Witherow, R. G.

1975-01-01

Requirements exist for an extremely stable, high performance, all-weather tethered aerostat system. This requirement has been satisfied by a 250,000 cubic foot captive buoyant vehicle as demonstrated by over a year of successful field operations. This achievement required significant advancements in several technology areas including composite materials design, aerostatics and aerodynamics, structural design, electro-mechanical design, vehicle fabrication and mooring operations. This paper specifically addresses the materials and structural design aspects of pressurized buoyant vehicles as related to the general class of Lighter Than Air vehicles.

Field tests of acoustic telemetry for a portable coastal observatory

USGS Publications Warehouse

Martini, M.; Butman, B.; Ware, J.; Frye, D.

2006-01-01

Long-term field tests of a low-cost acoustic telemetry system were carried out at two sites in Massachusetts Bay. At each site, an acoustic Doppler current profiler mounted on a bottom tripod was fitted with an acoustic modem to transmit data to a surface buoy; electronics mounted on the buoy relayed these data to shore via radio modem. The mooring at one site (24 m water depth) was custom-designed for the telemetry application, with a custom designed small buoy, a flexible electro-mechanical buoy to mooring joint using a molded chain connection to the buoy, quick-release electro-mechanical couplings, and dual hydrophones suspended 7 m above the bottom. The surface buoy at the second site (33 m water depth) was a U.S. Coast Guard (USCG) channel buoy fitted with telemetry electronics and clamps to hold the hydrophones. The telemetry was tested in several configurations for a period of about four years. The custom-designed buoy and mooring provided nearly error-free data transmission through the acoustic link under a variety of oceanographic conditions for 261 days at the 24 m site. The electro mechanical joint, cables and couplings required minimal servicing and were very reliable, lasting 862 days deployed before needing repairs. The acoustic communication results from the USCG buoy were poor, apparently due to the hard cobble bottom, noise from the all-steel buoy, and failure of the hydrophone assembly. Access to the USCG buoy at sea required ideal weather. ??2006 IEEE.

Advanced mooring method for installation of Enserch Garden Banks 388 FPF mooring legs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Honig, H.J.; Koolwijk, W.; Scovell, D.C.

1995-12-31

In the fall of 1994 HeereMac v.o.f installed the 12 mooring legs for Enserch Exploration`s Floating Production Facility in Garden Banks Block 388 in the Gulf of Mexico with the SSCV Balder. The installation of the catenary mooring system, each leg comprising several varying sections of spiral strand wire and chain, required sufficient handling and maneuverability power of the vessel, while enough holding capacity and stiffness of the system had to be provided. The most important aspects of the actual installation of the mooring legs are explained, for example, the use of a purpose built tipping winch. The method selectedmore » by HeereMac for station-keeping the Balder was to use a minimum number of anchor lines in combination with a tug, in order to maintain position and at the same time have an easy and controlled method of maneuvering to a new position. The method of station-keeping the SSCV in this way is part of a development towards full position control with a spread of tugs. In this paper the station-keeping system is described and the offshore experiences with the system are discussed. Some future developments with respect to tug-assisted station-keeping systems are highlighted.« less

Natural variability of pCO2 and pH in the Atlantic and Pacific coastal margins of the U.S

NASA Astrophysics Data System (ADS)

Sutton, A. J.; Sabine, C. L.; Feely, R. A.; Newton, J.; Salisbury, J.; Vandemark, D. C.; Musielewicz, S. B.; Maenner-Jones, S.; Bott, R.; Lawrence-Slavas, N.

2011-12-01

The discovery that seawater chemistry is changing as a result of carbon dioxide (CO2) emissions, referred to as "ocean acidification", has prompted a large effort to understand how this changing chemistry will impact marine life. Changes in carbon chemistry have been documented in the open ocean; however, in dynamic coastal systems where many marine species live, ocean acidification and the natural biogeochemical variability that organisms are currently exposed to are poorly quantified. In 2010 we began equipping coastal moorings currently measuring pCO2 with pH and other biogeochemical sensors to measure ocean acidification parameters at 3 hour intervals in the surface water. Here we present the magnitude and diurnal to seasonal variability of pCO2 and pH during the first year of observations at 2 sites in the Atlantic and Pacific coastal margins of the U.S.: the Gulf of Maine and outer coast of Washington state. Both the magnitude and range of pCO2 and pH values were much greater at the coastal moorings compared to the open ocean mooring at Ocean Station Papa in the North Pacific and also varied between the two coastal mooring sites. We observed maximum pCO2 values in coastal waters exceeding predicted values for the open ocean at 2x pre-industrial CO2 levels. The range of pCO2 and pH values during this time series was approximately 4 times the range observed at open ocean mooring Papa (2007-2011 time series). In many cases, large variance was observed at short time scales, with values fluctuating more than 200 μatm pCO2 and 0.2 pH between 3-hour cycles. These types of observations are critical for understanding how ocean acidification will manifest in naturally dynamic coastal systems and for informing the experimental design of species response studies that aim to mimic carbon chemistry experienced by coastal marine organisms.

Model-based assessment of a Northwestern Tropical Pacific moored array to monitor intraseasonal variability

NASA Astrophysics Data System (ADS)

Liu, Danian; Zhu, Jiang; Shu, Yeqiang; Wang, Dongxiao; Wang, Weiqiang; Cai, Shuqun

2018-06-01

The Northwestern Tropical Pacific Ocean (NWTPO) moorings observing system, including 15 moorings, was established in 2013 to provide velocity profile data. Observing system simulation experiments (OSSEs) were carried out to assess the ability of the observation system to monitor intraseasonal variability in a pilot study, where ideal "mooring-observed" velocity was assimilated using Ensemble Optimal Interpolation (EnOI) based on the Regional Oceanic Modeling System (ROMS). Because errors between the control and "nature" runs have a mesoscale structure, a random ensemble derived from 20-90-day bandpass-filtered nine-year model outputs is proved to be more appropriate for the NWTPO mooring array assimilation than a random ensemble derived from a 30-day running mean. The simulation of the intraseasonal currents in the North Equatorial Current (NEC), North Equatorial Countercurrent (NECC), and Equatorial Undercurrent (EUC) areas can be improved by assimilating velocity profiles using a 20-90-day bandpass-filtered ensemble. The root mean square errors (RMSEs) of the intraseasonal zonal (U) and meridional velocity (V) above 500 m depth within the study area (between 0°N-18°N and 122°E-147°E) were reduced by 15.4% and 16.9%, respectively. Improvements in the downstream area of the NEC moorings transect were optimum where the RMSEs of the intraseasonal velocities above 500 m were reduced by more than 30%. Assimilating velocity profiles can have a positive impact on the simulation and forecast of thermohaline structure and sea level anomalies in the ocean.

Experimental Comparison of Dynamic Responses of a Tension Moored Floating Wind Turbine Platform with and without Spring Dampers

NASA Astrophysics Data System (ADS)

Wright, C.; O'Sullivan, K.; Murphy, J.; Pakrashi, V.

2015-07-01

The offshore wind industry is rapidly maturing and is now expanding to more extreme environments in deeper water and farther from shore. To date fixed foundation types (i.e. monopoles, jackets) have been primarily used but become uneconomical in water depths greater than 50m. Floating foundations have more complex dynamics but at the moment no design has reached commercialization, although a number of devices are being tested at prototype stage. The development of concepts is carried out through physical model testing of scaled devices such that to better understand the dynamics of the system and validate numerical models. This paper investigates the testing of a scale model of a tension moored wind turbine at two different scales and in the presence and absence of a spring damper controlling its dynamic response. The models were tested under combined wave and wind thrust loading conditions. The analysis compares the motions of the platform at different scales and structural conditions through RAO, testing a mooring spring damper for load reductions.

Uncovering hidden heterogeneity: Geo-statistical models illuminate the fine scale effects of boating infrastructure on sediment characteristics and contaminants.

PubMed

Hedge, L H; Dafforn, K A; Simpson, S L; Johnston, E L

2017-06-30

Infrastructure associated with coastal communities is likely to not only directly displace natural systems, but also leave environmental footprints' that stretch over multiple scales. Some coastal infrastructure will, there- fore, generate a hidden layer of habitat heterogeneity in sediment systems that is not immediately observable in classical impact assessment frameworks. We examine the hidden heterogeneity associated with one of the most ubiquitous coastal modifications; dense swing moorings fields. Using a model based geo-statistical framework we highlight the variation in sedimentology throughout mooring fields and reference locations. Moorings were correlated with patches of sediment with larger particle sizes, and associated metal(loid) concentrations in these patches were depressed. Our work highlights two important ideas i) mooring fields create a mosaic of habitat in which contamination decreases and grain sizes increase close to moorings, and ii) model- based frameworks provide an information rich, easy-to-interpret way to communicate complex analyses to stakeholders. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

Evaluation of tropical Pacific observing systems using NCEP and GFDL ocean data assimilation systems

NASA Astrophysics Data System (ADS)

Xue, Yan; Wen, Caihong; Yang, Xiaosong; Behringer, David; Kumar, Arun; Vecchi, Gabriel; Rosati, Anthony; Gudgel, Rich

2017-08-01

The TAO/TRITON array is the cornerstone of the tropical Pacific and ENSO observing system. Motivated by the recent rapid decline of the TAO/TRITON array, the potential utility of TAO/TRITON was assessed for ENSO monitoring and prediction. The analysis focused on the period when observations from Argo floats were also available. We coordinated observing system experiments (OSEs) using the global ocean data assimilation system (GODAS) from the National Centers for Environmental Prediction and the ensemble coupled data assimilation (ECDA) from the Geophysical Fluid Dynamics Laboratory for the period 2004-2011. Four OSE simulations were conducted with inclusion of different subsets of in situ profiles: all profiles (XBT, moorings, Argo), all except the moorings, all except the Argo and no profiles. For evaluation of the OSE simulations, we examined the mean bias, standard deviation difference, root-mean-square difference (RMSD) and anomaly correlation against observations and objective analyses. Without assimilation of in situ observations, both GODAS and ECDA had large mean biases and RMSD in all variables. Assimilation of all in situ data significantly reduced mean biases and RMSD in all variables except zonal current at the equator. For GODAS, the mooring data is critical in constraining temperature in the eastern and northwestern tropical Pacific, while for ECDA both the mooring and Argo data is needed in constraining temperature in the western tropical Pacific. The Argo data is critical in constraining temperature in off-equatorial regions for both GODAS and ECDA. For constraining salinity, sea surface height and surface current analysis, the influence of Argo data was more pronounced. In addition, the salinity data from the TRITON buoys played an important role in constraining salinity in the western Pacific. GODAS was more sensitive to withholding Argo data in off-equatorial regions than ECDA because it relied on local observations to correct model biases and there were few XBT profiles in those regions. The results suggest that multiple ocean data assimilation systems should be used to assess sensitivity of ocean analyses to changes in the distribution of ocean observations to get more robust results that can guide the design of future tropical Pacific observing systems.

ISFET sensor evaluation and modification for seawater pH measurement

NASA Astrophysics Data System (ADS)

Martz, T. R.; Johnson, K. S.; Jannasch, H.; Coletti, L.; Barry, J.; Lovera, C.

2008-12-01

In the future, short-term cycles (daily to subannual) and long-term trends (annual and greater) in the carbonate system will be observed by autonomous sensors operating from a variety of platforms (e.g., moorings, profiling floats, AUVs, etc.). Of the four carbonate parameters, pH measurement has the longest history of development - yet robust autonomous sensing techniques remain elusive due to a catalog of technical challenges. Existing commercial sensor technologies generally do not meet the stringent demands of accuracy, long-term stability, low power, pressure tolerance, resistance to biofouling, and ease of use required by the oceanographic community. We report here on some recent advances in Ion Sensitive Field Effect Transistor (ISFET) technology that may open the door for more widespread autonomous seawater pH measurements. Much of our work has focused on applications of the Honeywell Durafet pH sensor, a product designed for industrial process control. Initial results from laboratory testing and deployments in the MBARI test tank and near shore moorings will be presented. Sensor calibration techniques will be addressed. Applications of now-available off-the-shelf sensors including shipboard underway measurement, shallow water mooring deployment, and a gas controlled seawater aquarium for pH perturbation experiments will be discussed. We hope that an ongoing collaboration between MBARI and Honeywell will result in a commercially available product, designed specifically for oceanographic applications, within the next several years.

Numerical modeling of a spherical buoy moored by a cable in three dimensions

NASA Astrophysics Data System (ADS)

Zhu, Xiangqian; Yoo, Wan-Suk

2016-05-01

Floating facilities have been studied based on the static analysis of mooring cables over the past decades. To analyze the floating system of a spherical buoy moored by a cable with a higher accuracy than before, the dynamics of the cables are considered in the construction of the numerical modeling. The cable modeling is established based on a new element frame through which the hydrodynamic loads are expressed efficiently. The accuracy of the cable modeling is verified with an experiment that is conducted by a catenary chain moving in a water tank. In addition, the modeling of a spherical buoy is established with respect to a spherical coordinate in three dimensions, which can suffers the gravity, the variable buoyancy and Froude-Krylov loads. Finally, the numerical modeling for the system of a spherical buoy moored by a cable is established, and a virtual simulation is proceeded with the X- and Y-directional linear waves and the X-directional current. The comparison with the commercial simulation code ProteusDS indicates that the system is accurately analyzed by the numerical modeling. The tensions within the cable, the motions of the system, and the relationship between the motions and waves are illustrated according to the defined sea state. The dynamics of the cables should be considered in analyzing the floating system of a spherical buoy moored by a cable.

Using present-day observations to detect when anthropogenic change forces surface ocean carbonate chemistry outside preindustrial bounds

NASA Astrophysics Data System (ADS)

Sutton, Adrienne J.; Sabine, Christopher L.; Feely, Richard A.; Cai, Wei-Jun; Cronin, Meghan F.; McPhaden, Michael J.; Morell, Julio M.; Newton, Jan A.; Noh, Jae-Hoon; Ólafsdóttir, Sólveig R.; Salisbury, Joseph E.; Send, Uwe; Vandemark, Douglas C.; Weller, Robert A.

2016-09-01

One of the major challenges to assessing the impact of ocean acidification on marine life is detecting and interpreting long-term change in the context of natural variability. This study addresses this need through a global synthesis of monthly pH and aragonite saturation state (Ωarag) climatologies for 12 open ocean, coastal, and coral reef locations using 3-hourly moored observations of surface seawater partial pressure of CO2 and pH collected together since as early as 2010. Mooring observations suggest open ocean subtropical and subarctic sites experience present-day surface pH and Ωarag conditions outside the bounds of preindustrial variability throughout most, if not all, of the year. In general, coastal mooring sites experience more natural variability and thus, more overlap with preindustrial conditions; however, present-day Ωarag conditions surpass biologically relevant thresholds associated with ocean acidification impacts on Mytilus californianus (Ωarag < 1.8) and Crassostrea gigas (Ωarag < 2.0) larvae in the California Current Ecosystem (CCE) and Mya arenaria larvae in the Gulf of Maine (Ωarag < 1.6). At the most variable mooring locations in coastal systems of the CCE, subseasonal conditions approached Ωarag = 1. Global and regional models and data syntheses of ship-based observations tended to underestimate seasonal variability compared to mooring observations. Efforts such as this to characterize all patterns of pH and Ωarag variability and change at key locations are fundamental to assessing present-day biological impacts of ocean acidification, further improving experimental design to interrogate organism response under real-world conditions, and improving predictive models and vulnerability assessments seeking to quantify the broader impacts of ocean acidification.

Fatigue analysis of the bow structure of FPSO

NASA Astrophysics Data System (ADS)

Hu, Zhi-Qiang; Gao, Zhen; Gu, Yong-Ning

2003-06-01

The bow structure of FPSO moored by the single mooring system is rather complicated. There are many potential hot spots in connection parts of structures between the mooring support frame and the forecastle. Mooring forces, which are induced by wave excitation and transferred by the YOKE and the mooring support frame, may cause fatigue damage to the bow structure. Different from direct wave-induced-forces, the mooring force consists of wave frequency force (WF) and 2nd draft low frequency force (LF)[3], which are represented by two sets of short-term distribution respectively. Based on two sets of short-term distribution of mooring forces obtained by the model test, the fatigue damage of the bow structure of FPSO is analyzed, with emphasis on two points. One is the procedure and position selection for fatigue check, and the other is the application of new formulae for the calculation of accumulative fatigue damage caused by two sets of short-term distribution of hot spot stress range. From the results distinguished features of fatigue damage to the FPSO’s bow structure can be observed.

Rocking the Boat: Damage to Eelgrass by Swinging Boat Moorings.

PubMed

Unsworth, Richard K F; Williams, Beth; Jones, Benjamin L; Cullen-Unsworth, Leanne C

2017-01-01

Seagrass meadows commonly reside in shallow sheltered embayments typical of the locations that provide an attractive option for mooring boats. Given the potential for boat moorings to result in disturbance to the seabed due to repeated physical impact, these moorings may present a significant threat to seagrass meadows. The seagrass Zostera marina (known as eelgrass) is extensive across the northern hemisphere, forming critical fisheries habitat and creating efficient long-term stores of carbon in sediments. Although boat moorings have been documented to impact seagrasses, studies to date have been conducted on the slow growing Posidonia species' rather than the fast growing and rapidly reproducing Z. marina that may have a higher capacity to resist and recover from repeated disturbance. In the present study we examine swinging chain boat moorings in seagrass meadows across a range of sites in the United Kingdom to determine whether such moorings have a negative impact on the seagrass Zostera marina at the local and meadow scale. We provide conclusive evidence from multiple sites that Z. marina is damaged by swinging chain moorings leading to a loss of at least 6 ha of United Kingdom seagrass. Each swinging chain mooring was found to result in the loss of 122 m 2 of seagrass. Loss is restricted to the area surrounding the mooring and the impact does not appear to translate to a meadow scale. This loss of United Kingdom seagrass from boat moorings is small but significant at a local scale. This is because it fragments existing meadows and ultimately reduces their resilience to other stressors. Boat moorings are prevalent in seagrass globally and it is likely this impairs their ecosystem functioning. Given the extensive ecosystem service value of seagrasses in terms of factors such as carbon storage and fish habitat such loss is of cause for concern. This indicates the need for the widespread use of seagrass friendly mooring systems in and around seagrass.

Rocking the Boat: Damage to Eelgrass by Swinging Boat Moorings

PubMed Central

Unsworth, Richard K. F.; Williams, Beth; Jones, Benjamin L.; Cullen-Unsworth, Leanne C.

2017-01-01

Seagrass meadows commonly reside in shallow sheltered embayments typical of the locations that provide an attractive option for mooring boats. Given the potential for boat moorings to result in disturbance to the seabed due to repeated physical impact, these moorings may present a significant threat to seagrass meadows. The seagrass Zostera marina (known as eelgrass) is extensive across the northern hemisphere, forming critical fisheries habitat and creating efficient long-term stores of carbon in sediments. Although boat moorings have been documented to impact seagrasses, studies to date have been conducted on the slow growing Posidonia species’ rather than the fast growing and rapidly reproducing Z. marina that may have a higher capacity to resist and recover from repeated disturbance. In the present study we examine swinging chain boat moorings in seagrass meadows across a range of sites in the United Kingdom to determine whether such moorings have a negative impact on the seagrass Zostera marina at the local and meadow scale. We provide conclusive evidence from multiple sites that Z. marina is damaged by swinging chain moorings leading to a loss of at least 6 ha of United Kingdom seagrass. Each swinging chain mooring was found to result in the loss of 122 m2 of seagrass. Loss is restricted to the area surrounding the mooring and the impact does not appear to translate to a meadow scale. This loss of United Kingdom seagrass from boat moorings is small but significant at a local scale. This is because it fragments existing meadows and ultimately reduces their resilience to other stressors. Boat moorings are prevalent in seagrass globally and it is likely this impairs their ecosystem functioning. Given the extensive ecosystem service value of seagrasses in terms of factors such as carbon storage and fish habitat such loss is of cause for concern. This indicates the need for the widespread use of seagrass friendly mooring systems in and around seagrass. PMID:28791040

WHOI Hawaii Ocean Timeseries Station (WHOTS): WHOTS-4 2007 Mooring Turnaround Cruise Report

DTIC Science & Technology

2008-01-01

a physical deterrence for pest birds and their accompanying guano deposition (Figure 7). The anti-bird wire is constructed of 316 stainless steel ...AutoIMET system installation on the Kilo Moana.................................................................8 Fig 6. WHOTS-4 mooring diagram ...buoyancy is lost. 11 Figure 6. WHOTS-4 mooring diagram . 12 b. Bird Barrier WHOTS-4 incorporates Nixalite Premium Bird Barrier Strips Model S as

Ultra-precision engineering in lithographic exposure equipment for the semiconductor industry.

PubMed

Schmidt, Robert-H Munnig

2012-08-28

The developments in lithographic tools for the production of an integrated circuit (IC) are ruled by 'Moore's Law': the density of components on an IC doubles in about every two years. The corresponding size reduction of the smallest detail in an IC entails several technological breakthroughs. The wafer scanner, the exposure system that defines those details, is the determining factor in these developments. This review deals with those aspects of the positioning systems inside these wafer scanners that enable the extension of Moore's Law into the future. The design of these systems is increasingly difficult because of the accuracy levels in the sub-nanometre range coupled with motion velocities of several metres per second. In addition to the use of feedback control for the reduction of errors, high-precision model-based feed-forward control is required with an almost ideally reproducible motion-system behaviour and a strict limitation of random disturbing events. The full mastering of this behaviour even includes material drift on an atomic scale and is decisive for the future success of these machines.

Typical power budget and possible energy source for Autonomous Oceanographic Network (AOSN) Labrador Sea Experiment (LSE). Technical report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henriksen, H.

1996-06-01

The Autonomous Oceanographic Network (AOSN) Labrador Sea Experiment (LSE) will be held in the Labrador Sea at a seawater depth of 3000 - 3500 meters. The total system will consist of a number of AUVs which will operate from a set of moorings within a defined area. Each mooring will be placed on the seafloor. The docking stations will be placed in the water column at 1000-2000 meters water depth. Each AUV will have at least one possible docking station to charge batteries and to transfer data. This report will show two different load pattern examples for the AOSN LSE,more » and the implications upon the power budget of the mooring. The possible use of a seawater battery and its implications upon the system will be discussed. A preliminary design of the sizes and weights of a seawater battery for this application is also included. Energy delivery to an experiment like the AOSN LSE with the use of a seawater battery is feasible both technically and within the time span of the AOSN project. The environment of the Labrador Sea is well documented and seems suitable to accommodate a seawater battery. Due to the large water depths involved and the simplicity of the system, and the lack of any large pressure housings the seawater battery seems like a good candidate both in respect to costs and feasibility.« less

Enabling More than Moore: Accelerated Reliability Testing and Risk Analysis for Advanced Electronics Packaging

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza; Evans, John W.

2014-01-01

For five decades, the semiconductor industry has distinguished itself by the rapid pace of improvement in miniaturization of electronics products-Moore's Law. Now, scaling hits a brick wall, a paradigm shift. The industry roadmaps recognized the scaling limitation and project that packaging technologies will meet further miniaturization needs or ak.a "More than Moore". This paper presents packaging technology trends and accelerated reliability testing methods currently being practiced. Then, it presents industry status on key advanced electronic packages, factors affecting accelerated solder joint reliability of area array packages, and IPC/JEDEC/Mil specifications for characterizations of assemblies under accelerated thermal and mechanical loading. Finally, it presents an examples demonstrating how Accelerated Testing and Analysis have been effectively employed in the development of complex spacecraft thereby reducing risk. Quantitative assessments necessarily involve the mathematics of probability and statistics. In addition, accelerated tests need to be designed which consider the desired risk posture and schedule for particular project. Such assessments relieve risks without imposing additional costs. and constraints that are not value added for a particular mission. Furthermore, in the course of development of complex systems, variances and defects will inevitably present themselves and require a decision concerning their disposition, necessitating quantitative assessments. In summary, this paper presents a comprehensive view point, from technology to systems, including the benefits and impact of accelerated testing in offsetting risk.

A case study of middle size floating airports for shallower and deeper waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yoshida, Koichiro; Suzuki, Hideyuki; Nishigaki, Makoto

1996-12-31

Demands for large and middle size airports are expanding in Japan with continuous increase of air transportation. However these demands will not be satisfied without effective ocean space utilization. Most of the wide and shallower waters suitable for reclamation have already been reclaimed. Furthermore those shallower waters are generally close to the residential area, and noise and environmental problems will be caused if they were used for airports. Deeper waters, which are relatively distant from the shore, are suitable for airport but reclamation of these waters are extremely difficult. This paper presents a structural planning of an open sea typemore » middle size floating airport to promote local economy and also improve transportation infrastructure of isolated islands. The airports of this plan are a semisubmersible type floating structure with a relatively thin deck, a number of slender columns and large size lower hulls. The floating structure is moored by inclined tension legs to restrain the motion. The diameter of the leg becomes much larger compared with the legs of existing tension leg platforms. Parameters related to the configuration of the floating structure and the mooring system are determined by comparing analyses results with the proper design criteria. Several kinds of static and dynamic computer programs are used in the planning. The proposed structural plan and the mooring system are considered as a typical floating airport appropriate for the open sea.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Colliat, J.L.; Boisard, P.; Andersen, K.

Shallow caisson foundations are considered as alternative anchors for permanent mooring of a process barge at an oil and gas field developed by ELF Congo in the Gulf of Guinea. The 12 mooring lines are scheduled to be installed on site in July 1995 and the process barge will be connected in 1996 for start of production. With a water depth of about 170m, this field will be the deepest one offshore Western Africa to date. The soils at the site consist of soft normally consolidated clays. The paper presents the results of a comparative study of potential anchor solutionsmore » for this production barge, including high capacity drag anchors, driven piles, and shallow caisson foundations installed by underpressure. This comparative study, including design, construction, and installation of the mooring system, has shown that the caisson foundations represent the best suited solution, technically as well as on an economical point of view, because of the following advantages: (1) vertical load capability, thus allowing to reduce the anchoring pattern, (2) once positioned on the seabed, the location of each anchor is fixed and known with accuracy, and (3) more simple and shorter installation procedure, since caisson anchors, as piles, do not require to be proof-loaded on site.« less

Prevalence of genetic thrombophilic polymorphisms in the Sri Lankan population--implications for association study design and clinical genetic testing services.

PubMed

Dissanayake, Vajira H W; Weerasekera, Lakshini Y; Gammulla, C Gayani; Jayasekara, Rohan W

2009-10-01

We investigated the prevalence of genotypes/alleles of single nucleotide polymorphisms (SNP) and haplotypes defined by them in three genes in which variations are associated with venous thromboembolism in 80 Sinhalese, 80 Sri Lankan Tamils and 80 Moors in the Sri Lankan population and compared the SNP data with that of other populations in Southern India and haplotype data with that of HapMap populations. The genes and polymorphisms investigated were Methylenetetrahydrofolate reductase (MTHFR) - 677C>T (rs1801133), 1298A>C (rs1801131), 1317T>C, 1793G>A (rs2274976); Factor V (F5) - 1691G>A (rs6025) and 4070A>G (rs1800595); and prothrombin (F2) - 20210G>A (rs1799963). The polymorphisms were genotyped using PCR/RFLP methods. The prevalence of the variant alleles of each polymorphism in the Sinhalese, Tamils, and Moors was MTHFR 677T: Sinhalese - 13%, Tamils - 9%, Moors - 9%. 1317T>C: Sinhalese - 0%; Tamils - 0%; Moors - 0%. 1793A: Sinhalese - 19%, Tamils - 19%, Moors - 19%. F5 1691A: Sinhalese - 2%, Tamils - 3%, Moors - 2%. 4070G: Sinhalese - 6%, Tamils - 5%, Moors - 8%. F2 20210A: Sinhalese - 0%, Tamils - 0%, Moors - 0%. The frequencies observed were similar to data from other South Indian populations; the haplotype data showed haplotypes unique to the Sri Lankan population when compared to HapMap populations. rs9651118 was identified as a SNP that splits the haplotypes harbouring the functionally significant 677T allele in the MTHFR gene. This data would be useful in planning genetic association studies in the Sri Lankan population and in deciding on which genetic variants should be tested in a clinical genetic testing service.

High Resolution Time Series Observations of Bio-Optical and Physical Variability in the Arabian Sea

DTIC Science & Technology

1998-09-30

1995-October 20, 1995). Multi-variable moored systems ( MVMS ) were deployed by our group at 35 and 80m. The MVMS utilizes a VMCM to measure currents...similar to that of the UCSB MVMSs. WORK COMPLETED Our MVMS interdisciplinary systems with sampling intervals of a few minutes were placed on a mooring

46 CFR 169.705 - Mooring equipment.

Code of Federal Regulations, 2010 CFR

2010-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Vessel Control, Miscellaneous Systems, and Equipment § 169.705 Mooring equipment. Each vessel must be fitted with... the size of the vessel and the waters on which it operates. ...

Optimizing observational networks combining gliders, moored buoys and FerryBox in the Bay of Biscay and English Channel

NASA Astrophysics Data System (ADS)

Charria, Guillaume; Lamouroux, Julien; De Mey, Pierre

2016-10-01

Designing optimal observation networks in coastal oceans remains one of the major challenges towards the implementation of future efficient Integrated Ocean Observing Systems to monitor the coastal environment. In the Bay of Biscay and the English Channel, the diversity of involved processes (e.g. tidally-driven circulation, plume dynamics) requires to adapt observing systems to the specific targeted environments. Also important is the requirement for those systems to sustain coastal applications. Two observational network design experiments have been implemented for the spring season in two regions: the Loire River plume (northern part of the Bay of Biscay) and the Western English Channel. The method used to perform these experiments is based on the ArM (Array Modes) formalism using an ensemble-based approach without data assimilation. The first experiment in the Loire River plume aims to explore different possible glider endurance lines combined with a fixed mooring to monitor temperature and salinity. Main results show an expected improvement when combining glider and mooring observations. The experiment also highlights that the chosen transect (along-shore and North-South, cross-shore) does not significantly impact the efficiency of the network. Nevertheless, the classification from the method results in slightly better performances for along-shore and North-South sections. In the Western English Channel, a tidally-driven circulation system, added value of using a glider below FerryBox temperature and salinity measurements has been assessed. FerryBox systems are characterised by a high frequency sampling rate crossing the region 2 to 3 times a day. This efficient sampling, as well as the specific vertical hydrological structure (which is homogeneous in many sub-regions of the domain), explains the fact that the added value of an associated glider transect is not significant. These experiments combining existing and future observing systems, as well as numerical ensemble simulations, highlight the key issue of monitoring the whole water column in and close to river plumes (using gliders for example) and the efficiency of the surface high frequency sampling from FerryBoxes in macrotidal regions.

Dynamics modeling and loads analysis of an offshore floating wind turbine

NASA Astrophysics Data System (ADS)

Jonkman, Jason Mark

The vast deepwater wind resource represents a potential to use offshore floating wind turbines to power much of the world with renewable energy. Many floating wind turbine concepts have been proposed, but dynamics models, which account for the wind inflow, aerodynamics, elasticity, and controls of the wind turbine, along with the incident waves, sea current, hydrodynamics, and platform and mooring dynamics of the floater, were needed to determine their technical and economic feasibility. This work presents the development of a comprehensive simulation tool for modeling the coupled dynamic response of offshore floating wind turbines, the verification of the simulation tool through model-to-model comparisons, and the application of the simulation tool to an integrated loads analysis for one of the promising system concepts. A fully coupled aero-hydro-servo-elastic simulation tool was developed with enough sophistication to address the limitations of previous frequency- and time-domain studies and to have the features required to perform loads analyses for a variety of wind turbine, support platform, and mooring system configurations. The simulation capability was tested using model-to-model comparisons. The favorable results of all of the verification exercises provided confidence to perform more thorough analyses. The simulation tool was then applied in a preliminary loads analysis of a wind turbine supported by a barge with catenary moorings. A barge platform was chosen because of its simplicity in design, fabrication, and installation. The loads analysis aimed to characterize the dynamic response and to identify potential loads and instabilities resulting from the dynamic couplings between the turbine and the floating barge in the presence of combined wind and wave excitation. The coupling between the wind turbine response and the barge-pitch motion, in particular, produced larger extreme loads in the floating turbine than experienced by an equivalent land-based turbine. Instabilities were also found in the system. The influence of conventional wind turbine blade-pitch control actions on the pitch damping of the floating turbine was also assessed. Design modifications for reducing the platform motions, improving the turbine response, and eliminating the instabilities are suggested. These suggestions are aimed at obtaining cost-effective designs that achieve favorable performance while maintaining structural integrity.

Feasibility of Floating Platform Systems for Wind Turbines: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musial, W.; Butterfield, S.; Boone, A.

This paper provides a general technical description of several types of floating platforms for wind turbines. Platform topologies are classified into multiple- or single-turbine floaters and by mooring method. Platforms using catenary mooring systems are contrasted to vertical mooring systems and the advantages and disadvantages are discussed. Specific anchor types are described in detail. A rough cost comparison is performed for two different platform architectures using a generic 5-MW wind turbine. One platform is a Dutch study of a tri-floater platform using a catenary mooring system, and the other is a mono-column tension-leg platform developed at the National Renewable Energymore » Laboratory. Cost estimates showed that single unit production cost is $7.1 M for the Dutch tri-floater, and $6.5 M for the NREL TLP concept. However, value engineering, multiple unit series production, and platform/turbine system optimization can lower the unit platform costs to $4.26 M and $2.88 M, respectively, with significant potential to reduce cost further with system optimization. These foundation costs are within the range necessary to bring the cost of energy down to the DOE target range of $0.05/kWh for large-scale deployment of offshore floating wind turbines.« less

Optimization of an acoustic telemetry array for detecting transmitter-implanted fish

USGS Publications Warehouse

Clements, S.; Jepsen, D.; Karnowski, M.; Schreck, C.B.

2005-01-01

The development of miniature acoustic transmitters and economical, robust automated receivers has enabled researchers to study the movement patterns and survival of teleosts in estuarine and ocean environments, including many species and age-classes that were previously considered too small for implantation. During 2001-2003, we optimized a receiver mooring system to minimize gear and data loss in areas where current action or wave action and acoustic noise are high. In addition, we conducted extensive tests to determine (1) the performance of a transmitter and receiver (Vemco, Ltd.) that are widely used, particularly in North America and Europe and (2) the optimal placement of receivers for recording the passage of fish past a point in a linear-flow environment. Our results suggest that in most locations the mooring system performs well with little loss of data; however, boat traffic remains a concern due to entanglement with the mooring system. We also found that the reception efficiency of the receivers depends largely on the method and location of deployment. In many cases, we observed a range of 0-100% reception efficiency (the percentage of known transmissions that are detected while the receiver is within range of the transmitter) when using a conventional method of mooring. The efficiency was improved by removal of the mounting bar and obstructions from the mooring line. ?? Copyright by the American Fisheries Society 2005.

Analyzing SystemC Designs: SystemC Analysis Approaches for Varying Applications

PubMed Central

Stoppe, Jannis; Drechsler, Rolf

2015-01-01

The complexity of hardware designs is still increasing according to Moore's law. With embedded systems being more and more intertwined and working together not only with each other, but also with their environments as cyber physical systems (CPSs), more streamlined development workflows are employed to handle the increasing complexity during a system's design phase. SystemC is a C++ library for the design of hardware/software systems, enabling the designer to quickly prototype, e.g., a distributed CPS without having to decide about particular implementation details (such as whether to implement a feature in hardware or in software) early in the design process. Thereby, this approach reduces the initial implementation's complexity by offering an abstract layer with which to build a working prototype. However, as SystemC is based on C++, analyzing designs becomes a difficult task due to the complex language features that are available to the designer. Several fundamentally different approaches for analyzing SystemC designs have been suggested. This work illustrates several different SystemC analysis approaches, including their specific advantages and shortcomings, allowing designers to pick the right tools to assist them with a specific problem during the design of a system using SystemC. PMID:25946632

Analyzing SystemC Designs: SystemC Analysis Approaches for Varying Applications.

PubMed

Stoppe, Jannis; Drechsler, Rolf

2015-05-04

The complexity of hardware designs is still increasing according to Moore's law. With embedded systems being more and more intertwined and working together not only with each other, but also with their environments as cyber physical systems (CPSs), more streamlined development workflows are employed to handle the increasing complexity during a system's design phase. SystemC is a C++ library for the design of hardware/software systems, enabling the designer to quickly prototype, e.g., a distributed CPS without having to decide about particular implementation details (such as whether to implement a feature in hardware or in software) early in the design process. Thereby, this approach reduces the initial implementation's complexity by offering an abstract layer with which to build a working prototype. However, as SystemC is based on C++, analyzing designs becomes a difficult task due to the complex language features that are available to the designer. Several fundamentally different approaches for analyzing SystemC designs have been suggested. This work illustrates several different SystemC analysis approaches, including their specific advantages and shortcomings, allowing designers to pick the right tools to assist them with a specific problem during the design of a system using SystemC.

Issues With Access to Acquisition Data and Information in the Department of Defense: Doing Data Right in Weapon System Acquisition

DTIC Science & Technology

2016-04-30

Defense: Doing Data Right in Weapon System Acquisition Nancy Moore, Senior Management Scientist, RAND Megan McKernan, Defense Research Analyst...Access to Acquisition Data & Information in the Department of Defense: Doing Data Right in Weapon System Acquisition Nancy Moore, Senior Management...With Access to Acquisition Data and Information in the Department of Defense: Doing Data Right in Weapon System Acquisition Nancy Y. Moore—is a

Ocean Acoustic Tomography Mooring Design Study.

DTIC Science & Technology

1982-04-01

mounted in RP. - RP contains its own power source. - Dead -weight anchor. - Acoustic Release is located in the RP. Configurations 1. - Top buoyancy...float is a steel sphere. icI - USS 3 x 19 jacketed wire rope is used as the tension member. - Anchor is dead -weight. - Acoustic Release is located...Receiver/Satellite Telemetry Moorings (RT) - Receiver depth 1000 - 3500 m. - Ocean depth is 5000 m. - Receiver contains its own power source. - Dead

Engineer Design of a Mono-Mooring System.

DTIC Science & Technology

1966-01-01

swivels . When asked whether the bogie rails were machined by a large radius boring mill , Mr. Coombe indicated that these rails are rolled then V welded...lifted aboard the transp ort vessel , the disposi- tion of the various system compo- nents shall be as follows: 1. Buoy shall be complete , with...tugboat , equipped with towing winch or pow9r capstan , LOA 110 ’ — 120’, twin screw; BHP-l000 minimum . 7. It has been assumed that weld- ing machines

Reinventing Douglas: How One Library Revamped Its Space

ERIC Educational Resources Information Center

Tarabula, Jill M.

2013-01-01

community just outside the city of Plattsburgh in upstate New York. It is part of the State University of New York (SUNY) system. The Leroy M. Douglas Sr. Library (Douglas Library) is located in the George Moore Academic and Administrative Building (Moore Building). Prior to…

The detrimental consequences for seagrass of ineffective marine park management related to boat anchoring.

PubMed

La Manna, G; Donno, Y; Sarà, G; Ceccherelli, G

2015-01-15

Posidonia oceanica (L.) Delile meadows are recognized as priority habitat for conservation by the EU Habitats Directive. The La Maddalena Archipelago National Park (Mediterranean Sea) P. oceanica meadow, the dominant coastal habitat of the area, is mostly threatened by boat anchoring. 12 years after the establishment of mooring fields and anchoring restrictions, a study was conducted to measure their effectiveness on the conservation of seagrass and the mitigation of anchoring damage. We found that: (i) the condition of P. oceanica was disturbed, both in the mooring fields and in control locations; (ii) mooring fields and anchoring restrictions did not show to be an efficient system for the protection of seagrass, in fact anchor scars increased after the tourist season; (iii) the mooring systems had an impact on the surrounding area of the meadow, probably due to their misuse. On the basis of these results, management recommendations for marine parks are proposed. Copyright © 2014 Elsevier Ltd. All rights reserved.

Book Review

NASA Astrophysics Data System (ADS)

Clevers, J. G. P. W.

2015-02-01

About thirty years after the previous advanced textbook on Microwave Remote Sensing by Ulaby, Moore and Fung has been published as three separate volumes, now an up-to-date new textbook has been published. The 1000-page book covers theoretical models, system design and operation, and geoscientific applications of active and passive microwave remote sensing systems. It is designed as a textbook at the postgraduate level, as well as a reference for the practicing professional. The book is caught by a thorough introduction into the physics and mathematics of electrical engineering applied to microwave radiation. Here on overview of its chapters with a short description of its focus will be given.

Real-time seismic data from the coastal ocean

USGS Publications Warehouse

Frye, D.; ten Brink, Uri S.; Paul, W.; Peal, K.; Von Der Heydt, K.

2003-01-01

A moored-buoy system for collecting real-time seismic data from the coastal ocean has been developed and will be deployed for its initial field trial in the fall of 2003. The key component in this moored system is an ultra-stretchy mooring hose that provides compliance for waves and currents and protects the electrical conductors connecting an Ocean Bottom Seismometer (OBS) to a surface buoy from the effects of bending and stretching. This hose is able to stretch to more than twice its unstretched length of 30 m without putting excessive strain on the electrical conductors embedded in its wall. In the initial trials of this system, the OBS will be deployed on the bottom in 40 m of water and connected to the mooring hose through a cable on the seafloor. It will transmit continuous data at a rate of about 5,000 bps to a radio link in the surface buoy. A repeater modem located at the Gay Head lighthouse on Martha's Vineyard about 18 km from the mooring site will receive the transmissions and forward the data to our laboratory at WHOI, about 46 km distant. A GPS receiver on the surface buoy will be configured to send accurate and synchronized time to the OBS on the seafloor, which will make it possible to include data from these undersea systems in the existing seismic data network without the need for any preprocessing. Power to operate the RF link and the OBS will be supplied by solar panels and rechargeable batteries on the surface buoy.

Passive Autonomous Acoustic Monitoring of Marine Mammals: System Development Using Seaglider (Trademark)

DTIC Science & Technology

2015-01-30

plan was to run sg178 in offshore-onshore transects with one end at J. Hildebrand’s HARP mooring at approximately 47° 30’N, 125° 21’W. Seaglider sg179...was to survey along the Washington coast just offshore of the 1000m isobath, with significant time spent surveying atop the HARP mooring mentioned...operations. Figure 4. Surfacing positions of Seagliders S/N178 (green) and S/N179 (red) 11JUN-12JUL2012. HARP mooring locations (Wiggins, private

Water turbine system and method of operation

DOEpatents

Costin, Daniel P [Montpelier, VT

2011-05-10

A system for providing electrical power from a current turbine is provided. The system includes a floatation device and a mooring. A water turbine structure is provided having an upper and lower portion wherein the lower portion includes a water fillable chamber. A plurality of cables are used to couple the system where a first cable couples the water turbine to the mooring and a second cable couples the floatation device to the first cable. The system is arranged to allow the turbine structure to be deployed and retrieved for service, repair, maintenance and redeployment.

Water turbine system and method of operation

DOEpatents

Costin, Daniel P [Montpelier, VT

2009-02-10

A system for providing electrical power from a current turbine is provided. The system includes a floatation device and a mooring. A water turbine structure is provided having an upper and lower portion wherein the lower portion includes a water fillable chamber. A plurality of cables are used to couple the system where a first cable couples the water turbine to the mooring and a second cable couples the floatation device to the first cable. The system is arranged to allow the turbine structure to be deployed and retrieved for service, repair, maintenance and redeployment.

Water turbine system and method of operation

DOEpatents

Costin, Daniel P.

2010-06-15

A system for providing electrical power from a current turbine is provided. The system includes a floatation device and a mooring. A water turbine structure is provided having an upper and lower portion wherein the lower portion includes a water fillable chamber. A plurality of cables are used to couple the system where a first cable couples the water turbine to the mooring and a second cable couples the floatation device to the first cable. The system is arranged to allow the turbine structure to be deployed and retrieved for service, repair, maintenance and redeployment.

MOORE: A prototype expert system for diagnosing spacecraft problems

NASA Technical Reports Server (NTRS)

Howlin, Katherine; Weissert, Jerry; Krantz, Kerry

1988-01-01

MOORE is a rule-based, prototype expert system that assists in diagnosing operational Tracking and Data Relay Satellite (TDRS) problems. It is intended to assist spacecraft engineers at the TDRS ground terminal in trouble shooting problems that are not readily solved with routine procedures, and without expert counsel. An additional goal of the prototype system is to develop in-house expert system and knowledge engineering skills. The prototype system diagnoses antenna pointing and earth pointing problems that may occur within the TDRS Attitude Control System (ACS). Plans include expansion to fault isolation of problems in the most critical subsystems of the TDRS spacecraft. Long term benefits are anticipated with use of an expert system during future TDRS programs with increased mission support time, reduced problem solving time, and retained expert knowledge and experience. Phase 2 of the project is intended to provide NASA the necessary expertise and capability to define requirements, evaluate proposals, and monitor the development progress of a highly competent expert system for NASA's Tracking Data Relay Satellite. Phase 2 also envisions addressing two unexplored applications for expert systems, spacecraft integration and tests (I and T) and support to launch activities. The concept, goals, domain, tools, knowledge acquisition, developmental approach, and design of the expert system. It will explain how NASA obtained the knowledge and capability to develop the system in-house without assistance from outside consultants. Future plans will also be presented.

Computing beyond Moore's Law

DOE PAGES

Shalf, John M.; Leland, Robert

2015-12-01

Here, photolithography systems are on pace to reach atomic scale by the mid-2020s, necessitating alternatives to continue realizing faster, more predictable, and cheaper computing performance. If the end of Moore's law is real, a research agenda is needed to assess the viability of novel semiconductor technologies and navigate the ensuing challenges.

Modular Seafloor and Water Column Systems for the Ocean Observatories Initiative Cabled Array

NASA Astrophysics Data System (ADS)

Delaney, J. R.; Manalang, D.; Harrington, M.; Tilley, J.; Dosher, J.; Cram, G.; Harkins, G.; McGuire, C.; Waite, P.; McRae, E.; McGinnis, T.; Kenney, M.; Siani, C.; Michel-Hart, N.; Denny, S.; Boget, E.; Kawka, O. E.; Daly, K. L.; Luther, D. S.; Kelley, D. S.; Milcic, M.

2016-02-01

Over the past decade, cabled ocean observatories have become an increasingly important way to collect continuous real-time data at remote subsea locations. This has led to the development of a class of subsea systems designed and built specifically to distribute power and bandwidth among sensing instrumentation on the seafloor and throughout the water column. Such systems are typically powered by shore-based infrastructure and involve networks of fiber optic and electrical cabling that provide real-time data access and control of remotely deployed instrumentation. Several subsea node types were developed and/or adapted for cabled use in order to complete the installation of the largest North American scientific cabled observatory in Oct, 2014. The Ocean Observatories Initiative (OOI) Cabled Array, funded by the US National Science Foundation, consists of a core infrastructure that includes 900 km of fiber optic/electrical cables, seven primary nodes, 18 seafloor junction boxes, three mooring-mounted winched profiling systems, and three wire-crawling profiler systems. In aggregate, the installed infrastructure has 200 dedicated scientific instrument ports (of which 120 are currently assigned), and is capable of further expansion. The installed system has a 25-year design life for reliable, sustained monitoring; and all nodes, profilers and instrument packages are ROV-serviceable. Now in it's second year of operation, the systems that comprise the Cabled Array are providing reliable, 24/7 real-time data collection from deployed instrumentation, and offer a modular and scalable class of subsea systems for ocean observing. This presentation will provide an overview of the observatory-class subsystems of the OOI Cabled Array, focusing on the junction boxes, moorings and profilers that power and communicate with deployed instrumentation.

Moore's law realities for recording systems and memory storage components: HDD, tape, NAND, and optical

NASA Astrophysics Data System (ADS)

Fontana, Robert E.; Decad, Gary M.

2018-05-01

This paper describes trends in the storage technologies associated with Linear Tape Open (LTO) Tape cartridges, hard disk drives (HDD), and NAND Flash based storage devices including solid-state drives (SSD). This technology discussion centers on the relationship between cost/bit and bit density and, specifically on how the Moore's Law perception that areal density doubling and cost/bit halving every two years is no longer being achieved for storage based components. This observation and a Moore's Law Discussion are demonstrated with data from 9-year storage technology trends, assembled from publically available industry reporting sources.

The hydrodynamic model testing for closed loop DP assisted mooring

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aalbers, A.B.; Merchant, A.A.

1996-12-31

Far East Levingston Shipbuilding (FELS) is presently completing the construction of the Smedvig Production Unit SPU 380, which will be operated as FPSO for Esso Balder Field Offshore Norway. In good cooperation with FELS and ND and A Inc. of Houston an extensive model test program was carried out for approval and optimization of the DP assisted mooring system. The main aspects were: investigate the performance of the mooring in two water depths, i.e. 250 m and 70 m; optimization of DP control for the three azimuthing thrusters; measurement of motions and wave induced loads at e.g., the bilge keels,more » keel and deckhouse front; and determination of limit sea state for turning the vessel around against the weather. The tests were carried out in the Wave and Current Basin of MARIN, using a closed loop DP control system to steer the thrusters. The paper presents the findings with respect to the effect of DP control strategy on mooring loads and presents selected results of wave induced loads on bilge keels and deck house.« less

Development of mooring-anchor program in public domain for coupling with floater program for FOWTs (Floating Offshore Wind Turbines)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, MooHyun

2014-08-01

This report presents the development of offshore anchor data sets which are intended to be used to develop a database that allows preliminary selection and sizing of anchors for the conceptual design of floating offshore wind turbines (FOWTs). The study is part of a project entitled “Development of Mooring-Anchor Program in Public Domain for Coupling with Floater Program for FOWTs (Floating Offshore Wind Turbines)”, under the direction of Dr. Moo-Hyun Kim at the Texas A&M University and with the sponsorship from the US Department of Energy (Contract No. DE-EE0005479, CFDA # 81.087 for DE-FOA-0000415, Topic Area 1.3: Subsurface Mooring andmore » Anchoring Dynamics Models).« less

Frontiers of More than Moore in Bioelectronics and the Required Metrology Needs

NASA Astrophysics Data System (ADS)

Guiseppi-Elie, Anthony; Kotanen, Christian; Wilson, A. Nolan

2011-11-01

Silicon's intersection with biology is a premise inherent in Moore's prediction. Distinct from biologically inspired molecular logic and storage devices (more Moore) are the integration of solid state electronic devices with the soft condensed state of the body (more than Moore). Developments in biomolecular recognition events per sq. cm parallel those of Moore's Law. However, challenges continue in the area of "More than Moore". Two grand challenge problems must be addressed—the biocompatibility of synthetic materials with the myriad of tissue types within the human body and the interfacing of solid state micro- and nano-electronic devices with the electronics of biological systems. Electroconductive hydrogels have been developed as soft, condensed, biomimetic but otherwise inherently electronically conductive materials to address the challenge of interfacing solid state devices with the electronics of the body, which is predominantly ionic. Nano-templated interfaces via the oriented immobilization of single walled carbon nanotubes (SWCNTs) onto metallic electrodes have engendered reagentless, direct electron transfer between biological redox enzymes and solid state electrodes. In addressing these challenges, metrology needs and opportunities are found in such widely diverse areas as single molecule counting and addressing, sustainable power requirements such as the development of implantable biofuel cells for the deployment of implantable biochips, and new manufacturing paradigms to address plura-biology needs on solid state devices.

MoPCoM Methodology: Focus on Models of Computation

NASA Astrophysics Data System (ADS)

Koudri, Ali; Champeau, Joël; Le Lann, Jean-Christophe; Leilde, Vincent

Today, developments of Real Time Embedded Systems have to face new challenges. On the one hand, Time-To-Market constraints require a reliable development process allowing quick design space exploration. On the other hand, rapidly developing technology, as stated by Moore's law, requires techniques to handle the resulting productivity gap. In a previous paper, we have presented our Model Based Engineering methodology addressing those issues. In this paper, we make a focus on Models of Computation design and analysis. We illustrate our approach on a Cognitive Radio System development implemented on an FPGA. This work is part of the MoPCoM research project gathering academic and industrial organizations (http://www.mopcom.fr).

Flow-Induced Oscillations of OTEC Mooring and Anchoring Cables: State of the Art.

DTIC Science & Technology

1982-05-27

general, including heat exchangers , overhead transmission lines, and marine structures and cables. A flowchart that describes the steps necessary to...34Crossflow-Induced Vibrations of Heat Exchanger Tube Banks," Nuc. Engrg. and Design, Vol. 47, 67-86, 1978. 22. O.M. Griffin and S.E. Ramberg, "On...AD-AIlS 462 NAVAL RESEARCH LAB WASHINGTON DC F/6 13/13 FLOW-INOUCED OSCILLATIONS OF OTEC MOORING AND ANCHORING CABLES --ETC(UI MAY 62 0 M GRIFFIN

Discrimination of Amplitude-Modulated Synthetic Echo Trains by an Echolocating Bottlenose Dolphin

DTIC Science & Technology

2002-07-09

resulted in improved echo categorization (Moore FIG. 1. (A) Enlargement of a single stimulus pulse (left) and its spectrum eta!., 1991; Roitblat eta!., 1991...Floyd, 1980; Moore et aL., 1991; Roitblat J. Acoust. Soc. Am., Vol. 112, No. 4, October 2002 Dankiewicz et al.: Discrimination of AM by an...Those studies were designed to elu- Harley, H. E., Roitblat , H. L., and Nachtigall, P. E. (1996). "Object repre- cidate the possible mechanisms by which

33 CFR 149.625 - What are the design standards?

Code of Federal Regulations, 2010 CFR

2010-07-01

... elsewhere in this subpart (for example, single point moorings, hoses, and aids to navigation buoys), must be... components. (c) Heliports on floating deepwater ports must be designed in compliance with the regulations at...

Extraordinary flood response of a small urban watershed to short-duration convective rainfall

USGS Publications Warehouse

Smith, J.A.; Miller, A.J.; Baeck, M.L.; Nelson, P.A.; Fisher, G.T.; Meierdiercks, K.L.

2005-01-01

The 9.1 km2 Moores Run watershed in Baltimore, Maryland, experiences floods with unit discharge peaks exceeding 1 m3 s-1 km-2 12 times yr-1, on average. Few, if any, drainage basins in the continental United States have a higher frequency. A thunderstorm system on 13 June 2003 produced the record flood peak (13.2 m3 s-1 km-2) during the 6-yr stream gauging record of Moores Run. In this paper, the hydrometeorology, hydrology, and hydraulics of extreme floods in Moores Run are examined through analyses of the 13 June 2003 storm and flood, as well as other major storm and flood events during the 2000-03 time period. The 13 June 2003 flood, like most floods in Moores Run, was produced by an organized system of thunderstorms. Analyses of the 13 June 2003 storm, which are based on volume scan reflectivity observations from the Sterling, Virginia, WSR-88D radar, are used to characterize the spatial and temporal variability of flash flood producing rainfall. Hydrology of flood response in Moores Run is characterized by highly efficient concentration of runoff through the storm drain network and relatively low runoff ratios. A detailed survey of high-water marks for the 13 June 2003 flood is used, in combination with analyses based on a 2D, depth-averaged open channel flow model (TELEMAC 2D) to examine hydraulics of the 13 June 2003 flood. Hydraulic analyses are used to examine peak discharge estimates for the 13 June flood peak, propagation of flood waves in the Moores Run channel, and 2D flow features associated with channel and floodplain geometry. ?? 2005 American Meteorological Society.

Fleet Mooring Underwater Inspection Report La Maddalena, Italy.

DTIC Science & Technology

1981-12-01

Peg Top mooring buoys at the bow at the NATO Naval Facility, St. Stefano , Sardinia, Italy. The ship using the mooring is moored at the stern to the...LAT: NSO LA MADDALENA NORTH RISER/MED MOOR LON:SANTO STEFANO ,ISardinia, Italy ii DATE DIVERS U 1WATER DEPTH SUPERVISOR INITIALS 5. INSPECTION 18-25 Sep...0) 0 蟙 W. .-. MOORING INSPECTION REPORT Page 3 of 3 1. FACILITY 2. MOORING NO. 13. TYPE/CLASSMOORING 4. LAT.RISER/MD MOOR SANTO STEFANO , NSO LA

Introduction to focus issue: intrinsic and designed computation: information processing in dynamical systems--beyond the digital hegemony.

PubMed

Crutchfield, James P; Ditto, William L; Sinha, Sudeshna

2010-09-01

How dynamical systems store and process information is a fundamental question that touches a remarkably wide set of contemporary issues: from the breakdown of Moore's scaling laws--that predicted the inexorable improvement in digital circuitry--to basic philosophical problems of pattern in the natural world. It is a question that also returns one to the earliest days of the foundations of dynamical systems theory, probability theory, mathematical logic, communication theory, and theoretical computer science. We introduce the broad and rather eclectic set of articles in this Focus Issue that highlights a range of current challenges in computing and dynamical systems.

Development of moored oceanographic spectroradiometer

NASA Technical Reports Server (NTRS)

Booth, Charles R.; Mitchell, B. Greg; Holm-Hansen, O.

1987-01-01

Biospherical Instruments has successfully completed a NASA sponsored SBIR (Small Business Innovational Research Program) project to develop spectroradiometers capable of being deployed in the ocean for long periods of time. The completion of this project adds a valuable tool for the calibration of future spaceborne ocean color sensors and enables oceanographers to extend remote sensing optical techniques beyond the intermittent coverage of spaceborne sensors. Highlights of the project include two moorings totalling 8 months generating extensive sets of optical, biological, and physical data sets in the ocean off La Jolla, California, and a 70 day operational deployment of the resulting commercial product by the ONR and NASA sponsored BIOWATT program. Based on experience gained in these moorings, Biospherical Instruments has developed a new line of spectroradiometers designed to support the oceanographic remote sensing missions of NASA, the Navy, and various oceanographers.

Efficient Distribution of Triggered Synchronous Block Diagrams

DTIC Science & Technology

2011-10-21

corresponding FFP processes, from P to P ′. The sizes of the queues are as in [23]. In particular, if M is not Moore, a queue of size 1 suffices; ifM is Moore...computer systems. Real-Time Systems, 14(3):219–250, 1998. [23] S . Tripakis, C. Pinello, A . Benveniste, A . Sangiovanni-Vincent, P. Caspi, and M . Di...of connections: a data connection connects some output port of a block M to some input port of another block M ′; a trigger connection connects some

Western Arctic Shelf-Basin Interactions Experiment: Processing and Calibration of Moored Profiler Data from the Beaufort Shelf Edge Mooring Array

DTIC Science & Technology

2006-12-01

EM-CTD and ACM data (MMP only) were extracted from a PC flashcard on the MP controller and converted to ASCII file format. The MP reports engineering...downloaded from the flashcards of the MP instruments and unpacked, we used the processing system developed by John Toole at the Woods Hole Oceanographic

46 CFR 184.300 - Ground tackle and mooring lines.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Ground tackle and mooring lines. 184.300 Section 184.300... Ground tackle and mooring lines. A vessel must be fitted with ground tackle and mooring lines necessary for the vessel to be safely anchored or moored. The ground tackle and mooring lines provided must be...

46 CFR 184.300 - Ground tackle and mooring lines.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 7 2011-10-01 2011-10-01 false Ground tackle and mooring lines. 184.300 Section 184.300... Ground tackle and mooring lines. A vessel must be fitted with ground tackle and mooring lines necessary for the vessel to be safely anchored or moored. The ground tackle and mooring lines provided must be...

Reference Model 5 (RM5): Oscillating Surge Wave Energy Converter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yu, Y. H.; Jenne, D. S.; Thresher, R.

This report is an addendum to SAND2013-9040: Methodology for Design and Economic Analysis of Marine Energy Conversion (MEC) Technologies. This report describes an Oscillating Water Column Wave Energy Converter (OSWEC) reference model design in a complementary manner to Reference Models 1-4 contained in the above report. A conceptual design for a taut moored oscillating surge wave energy converter was developed. The design had an annual electrical power of 108 kilowatts (kW), rated power of 360 kW, and intended deployment at water depths between 50 m and 100 m. The study includes structural analysis, power output estimation, a hydraulic power conversionmore » chain system, and mooring designs. The results were used to estimate device capital cost and annual operation and maintenance costs. The device performance and costs were used for the economic analysis, following the methodology presented in SAND2013-9040 that included costs for designing, manufacturing, deploying, and operating commercial-scale MEC arrays up to 100 devices. The levelized cost of energy estimated for the Reference Model 5 OSWEC, presented in this report, was for a single device and arrays of 10, 50, and 100 units, and it enabled the economic analysis to account for cost reductions associated with economies of scale. The baseline commercial levelized cost of energy estimate for the Reference Model 5 device in an array comprised of 10 units is $1.44/kilowatt-hour (kWh), and the value drops to approximately $0.69/kWh for an array of 100 units.« less

A Cabled, High Bandwidth Instrument Platform for Continuous Scanning of the Upper Ocean Water Column

NASA Astrophysics Data System (ADS)

McRae, E.; Delaney, J. R.; Kelly, D.; Daly, K. L.; Luther, D. S.; Harkins, G.; Harrington, M.; McGuire, C.; Tilley, J.; Dosher, J.; Waite, P.; Cram, G.; Kawka, O. E.

2016-02-01

The Cabled Array portion of the National Science Foundation funded Ocean Observatories Initiative is a large scale, high bandwidth and high power subsea science network designed by the University of Washington Applied Physics Laboratory. Part of that system is a set of winched profilers which continuously scan the upper 200m of the ocean at their deployment sites. The custom built profilers leverage the Cabled Array's technology for interfacing collections of science instruments and add the ability to run predefined missions and to switch missions or mission parameters on the fly via command from shore. The profilers were designed to operate continuously for up to two years after deployment after which certain wearing components must be replaced. The data from the profiler's science and engineering sensors are streamed to shore via the seafloor network in real time. Data channel capacity from the profilers exceeds 40 Mbps. For profiler safety, mission execution is controlled within the platform. Inputs such as 3D gyro, pressure depth and deployed cable calculations are monitored to assure safe operation during any sea state. The profilers never surface but are designed to approach within 5m of the surface if conditions allow. Substantial engineering effort was focused on reliable cable handling under all ocean conditions. The profilers are currently operated from subsea moorings which also contain sets of fixed science and engineering sensors. The profilers and their associated mooring instrument assemblies are designed for rapid replacement using ROVs. We have operated this system for two years, including one annual maintenance turn and information relative to that experience will be included in the paper.[Image Caption] Cabled Array Shallow Profiler shown in its parking position.

Finding a roadmap to achieve large neuromorphic hardware systems

PubMed Central

Hasler, Jennifer; Marr, Bo

2013-01-01

Neuromorphic systems are gaining increasing importance in an era where CMOS digital computing techniques are reaching physical limits. These silicon systems mimic extremely energy efficient neural computing structures, potentially both for solving engineering applications as well as understanding neural computation. Toward this end, the authors provide a glimpse at what the technology evolution roadmap looks like for these systems so that Neuromorphic engineers may gain the same benefit of anticipation and foresight that IC designers gained from Moore's law many years ago. Scaling of energy efficiency, performance, and size will be discussed as well as how the implementation and application space of Neuromorphic systems are expected to evolve over time. PMID:24058330

Tracking control of a marine surface vessel with full-state constraints

NASA Astrophysics Data System (ADS)

Yin, Zhao; He, Wei; Yang, Chenguang

2017-02-01

In this paper, a trajectory tracking control law is proposed for a class of marine surface vessels in the presence of full-state constraints and dynamics uncertainties. A barrier Lyapunov function (BLF) based control is employed to prevent states from violating the constraints. Neural networks are used to approximate the system uncertainties in the control design, and the control law is designed by using the Moore-Penrose inverse. The proposed control is able to compensate for the effects of full-state constraints. Meanwhile, the signals in the closed-loop system are guaranteed to be semiglobally uniformly bounded, with the asymptotic tracking being achieved. Finally, the performance of the proposed control has been tested and verified by simulation studies.

Time series pCO2 at a coastal mooring: Internal consistency, seasonal cycles, and interannual variability

NASA Astrophysics Data System (ADS)

Reimer, Janet J.; Cai, Wei-Jun; Xue, Liang; Vargas, Rodrigo; Noakes, Scott; Hu, Xinping; Signorini, Sergio R.; Mathis, Jeremy T.; Feely, Richard A.; Sutton, Adrienne J.; Sabine, Christopher; Musielewicz, Sylvia; Chen, Baoshan; Wanninkhof, Rik

2017-08-01

Marine carbonate system monitoring programs often consist of multiple observational methods that include underway cruise data, moored autonomous time series, and discrete water bottle samples. Monitored parameters include all, or some of the following: partial pressure of CO2 of the water (pCO2w) and air, dissolved inorganic carbon (DIC), total alkalinity (TA), and pH. Any combination of at least two of the aforementioned parameters can be used to calculate the others. In this study at the Gray's Reef (GR) mooring in the South Atlantic Bight (SAB) we: examine the internal consistency of pCO2w from underway cruise, moored autonomous time series, and calculated from bottle samples (DIC-TA pairing); describe the seasonal to interannual pCO2w time series variability and air-sea flux (FCO2), as well as describe the potential sources of pCO2w variability; and determine the source/sink for atmospheric pCO2. Over the 8.5 years of GR mooring time series, mooring-underway and mooring-bottle calculated-pCO2w strongly correlate with r-values > 0.90. pCO2w and FCO2 time series follow seasonal thermal patterns; however, seasonal non-thermal processes, such as terrestrial export, net biological production, and air-sea exchange also influence variability. The linear slope of time series pCO2w increases by 5.2 ± 1.4 μatm y-1 with FCO2 increasing 51-70 mmol m-2 y-1. The net FCO2 sign can switch interannually with the magnitude varying greatly. Non-thermal pCO2w is also increasing over the time series, likely indicating that terrestrial export and net biological processes drive the long term pCO2w increase.

Verification and Validation of the New Dynamic Mooring Modules Available in FAST v8: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendt, Fabian; Robertson, Amy; Jonkman, Jason

2016-08-01

The open-source aero-hydro-servo-elastic wind turbine simulation software, FAST v8, was recently coupled to two newly developed mooring dynamics modules: MoorDyn and FEAMooring. MoorDyn is a lumped-mass-based mooring dynamics module developed by the University of Maine, and FEAMooring is a finite-element-based mooring dynamics module developed by Texas A&M University. This paper summarizes the work performed to verify and validate these modules against other mooring models and measured test data to assess their reliability and accuracy. The quality of the fairlead load predictions by the open-source mooring modules MoorDyn and FEAMooring appear to be largely equivalent to what is predicted by themore » commercial tool OrcaFlex. Both mooring dynamic model predictions agree well with the experimental data, considering the given limitations in the accuracy of the platform hydrodynamic load calculation and the quality of the measurement data.« less

Verification and Validation of the New Dynamic Mooring Modules Available in FAST v8

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wendt, Fabian F.; Andersen, Morten T.; Robertson, Amy N.

2016-07-01

The open-source aero-hydro-servo-elastic wind turbine simulation software, FAST v8, was recently coupled to two newly developed mooring dynamics modules: MoorDyn and FEAMooring. MoorDyn is a lumped-mass-based mooring dynamics module developed by the University of Maine, and FEAMooring is a finite-element-based mooring dynamics module developed by Texas A&M University. This paper summarizes the work performed to verify and validate these modules against other mooring models and measured test data to assess their reliability and accuracy. The quality of the fairlead load predictions by the open-source mooring modules MoorDyn and FEAMooring appear to be largely equivalent to what is predicted by themore » commercial tool OrcaFlex. Both mooring dynamic model predictions agree well with the experimental data, considering the given limitations in the accuracy of the platform hydrodynamic load calculation and the quality of the measurement data.« less

Design of Buoys for Mounting Wind Turbines at Exposed Sites

NASA Astrophysics Data System (ADS)

Erdoğan, Beytullah; Çelıkkol, Barbaros; Swift, Robinson

2018-04-01

In this study, two designs for a buoy capable of supporting a 10 kW wind turbine and its tower were developed to operate at the University of New Hampshire's Center of Ocean Renewable Energy testing site located off the Isles of Shoals, New Hampshire. The buoys are to be moored by a catenary chain system. To evaluate wave response, two Froude-scaled models were constructed, tested, and compared at the Ocean Engineering wave tank at the University of New Hampshire. These buoys have been implemented and compared with wave tank measurements of the spar displacement at a reference elevation 2.44 m above the mean water level.

The hyperbolic problem

NASA Astrophysics Data System (ADS)

Gualdesi, Lavinio

2017-04-01

Mooring lines in the Ocean might be seen as a pretty simple seamanlike activity. Connecting valuable scientific instrumentation to it transforms this simple activity into a sophisticated engineering support which needs to be accurately designed, developed, deployed, monitored and hopefully recovered with its precious load of scientific data. This work is an historical travel along the efforts carried out by scientists all over the world to successfully predict mooring line behaviour through both mathematical simulation and experimental verifications. It is at first glance unexpected how many factors one must observe to get closer and closer to a real ocean situation. Most models have dual applications for mooring lines and towed bodies lines equations. Numerous references are provided starting from the oldest one due to Isaac Newton. In his "Philosophiae Naturalis Principia Matematica" (1687) the English scientist, while discussing about the law of motion for bodies in resistant medium, is envisaging a hyperbolic fitting to the phenomenon including asymptotic behaviour in non-resistant media. A non-exhaustive set of mathematical simulations of the mooring lines trajectory prediction is listed hereunder to document how the subject has been under scientific focus over almost a century. Pode (1951) Prior personal computers diffusion a tabular form of calculus of cable geometry was used by generations of engineers keeping in mind the following limitations and approximations: tangential drag coefficients were assumed to be negligible. A steady current flow was assumed as in the towed configuration. Cchabra (1982) Finite Element Method that assumes an arbitrary deflection angle for the top first section and calculates equilibrium equations down to the sea floor iterating up to a compliant solution. Gualdesi (1987) ANAMOOR. A Fortran Program based on iterative methods above including experimental data from intensive mooring campaign. Database of experimental drag coefficients obtained in wind tunnel for the instrumentation verified in ocean mooring. Dangov (1987) A set of Fortran routines, due to a Canadian scientist, to analyse discrepancies between model and experimental data due to strumming effect on mooring line. Acoustic Doppler Current Profiler's data were adopted for the first time as an input for the model. Skop and O' Hara (1968) Static analysis of a three dimensional multi-leg model Knutson (1987) A model developed at David taylor Model basin based on towed models. Henry Berteaux (1990) SFMOOR Iterative FEM analysis fully fitted with mooring components data base developed by a WHOI scientist. Henry Berteaux (1990) SSMOOR Same model applied to sub-surface moorings. Gobats and Grosenbaugh (1998) Fully developed Method based on Strip Theory developed by WHOI scientists. Experimental validation results are not known.

Floating Offshore WTG Integrated Load Analysis & Optimization Employing a Tuned Mass Damper

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodriguez Tsouroukdissian, Arturo; Lackner, Matt; Cross-Whiter, John

2015-09-25

Floating offshore wind turbines (FOWTs) present complex design challenges due to the coupled dynamics of the platform motion, mooring system, and turbine control systems, in response to wind and wave loading. This can lead to higher extreme and fatigue loads than a comparable fixed bottom or onshore system. Previous research[1] has shown the potential to reduced extreme and fatigue loads on FOWT using tuned mass dampers (TMD) for structural control. This project aims to reduce maximum loads using passive TMDs located at the tower top during extreme storm events, when grid supplied power for other controls systems may not bemore » available. The Alstom Haliade 6MW wind turbine is modelled on the Glosten Pelastar tension-leg platform (TLP). The primary objectives of this project are to provide a preliminary assessment of the load reduction potential of passive TMDs on real wind turbine and TLP designs.« less

HYDROBS: a long-term autonomous mooring for passive acoustic monitoring

NASA Astrophysics Data System (ADS)

Hello, Y.; Royer, J. Y.; Yegikyan, M.

2017-12-01

Passive acoustics proves an effective way for monitoring the low-level seismic activity of the ocean floor and low-frequency sounds from the ocean (baleen whales, sea-state, icebergs). Networks of synchronized autonomous hydrophones have thus been commonly deployed in the world ocean to monitor large sections of mid-oceanic ridges. HYDROBS is an improved system that meet two requirements: an easy access to the data collected by the instruments together with long-term deployments - up to 4 consecutive years - reducing the need of large vessels capable of yearly mooring operations in open seas. The system has two components: a data logger, up-to-date but similar to previous systems, and three messengers, releasable on demand to collect the data. The mooring line itself is classical, with an expandable weight at the sea-bottom to maintain the mooring, an acoustic release to free the mooring line for recovery, a line adjustable to the seafloor depth, and an immerged buoy, holding the acquisition system, to maintain the sensors at a constant depth and to bring the mooring line to the surface for its recovery. The data logger is based on a low-power microprocessor, an A/D-32bit convertor sampling at 250Hz, a 10-8 real time clock and SD card storage. Lithium batteries provide 3-4 years of autonomy. Acoustic communications with the surface-ship provide control over all functionalities at deployment and a health bulletin on demand. The 3 shuttles, encapsulated in 13" glass spheres, use the same CPU board and clock as the main station. Data transfer from the data logger to the shuttles is wireless (1Mbit/s digital inductive through water). Data are duplicated once per day on shuttles N and N+1 for redundancy. Prior to their release by acoustic command, the shuttles are synchronized with the master clock. At sea-surface, shuttles (as the main unit) look for GPS time and calculate their clock drift. So, the master clock drift can be monitored over time at every shuttle release until its final recovery. Shuttles and main unit are located on the sea-surface by AIS. Iridium communications can also be set to warn the user of a false release. A non-specialist can thus easily handle a shuttle recovery from a ship of opportunity. With 4-channels, this system is also suitable to monitor other parameters in the water column, continuously and over long periods.

Eddy Seeding in the Labrador Sea: a Submerged Autonomous Launching Platform (SALP) Application

NASA Astrophysics Data System (ADS)

Furey, Heather H.; Femke de Jong, M.; Bower, Amy S.

2013-04-01

A simplified Submerged Autonomous Launch Platform (SALP) was used to release profiling floats into warm-core Irminger Rings (IRs) in order to investigate their vertical structure and evolution in the Labrador Sea from September 2007 - September 2009. IRs are thought to play an important role in restratification after convection in the Labrador Sea. The SALP is designed to release surface drifters or subsurface floats serially from a traditional ocean mooring, using real-time ocean measurements as criteria for launch. The original prototype instrument used properties measured at multiple depths, with information relayed to the SALP controller via acoustic modems. In our application, two SALP carousels were attached at 500 meters onto a heavily-instrumented deep water mooring, in the path of recently-shed IRs off the west Greenland shelf. A release algorithm was designed to use temperature and pressure measured at the SALP depth only to release one or two APEX profiling drifters each time an IR passed the mooring, using limited historical observations to set release thresholds. Mechanically and electronically, the SALP worked well: out of eleven releases, there was only one malfunction when a float was caught in the cage after the burn-wire had triggered. However, getting floats trapped in eddies met with limited success due to problems with the release algorithm and float ballasting. Out of seven floats launched from the platform using oceanographic criteria, four were released during warm water events that were not related to passing IRs. Also, after float release, it took on average about 2.6 days for the APEX to adjust from its initial ballast depth, about 600 meters, to its park point of 300 meters, leaving the float below the trapped core of water in the IRs. The other mooring instruments (at depths of 100 to 3000 m), revealed that 12 IRs passed by the mooring in the 2-year monitoring period. With this independent information, we were able to assess and improve the release algorithm, still based on ocean conditions measured only at one depth. We found that much better performance could have been achieved with an algorithm that detected IRs based on a temperature difference from a long-term running mean rather than a fixed temperature threshold. This highlights the challenge of designing an appropriate release strategy with limited a priori information on the amplitude and time scales of the background variability.

Technical note: GODESS - a profiling mooring in the Gotland Basin

NASA Astrophysics Data System (ADS)

Prien, Ralf D.; Schulz-Bull, Detlef E.

2016-07-01

This note describes a profiling mooring with an interdisciplinary suite of sensors taking profiles between 180 and 30 m depth. It consists of an underwater winch, moored below 180 m depth, and a profiling instrumentation platform. In its described setup it can take about 200 profiles at pre-programmed times or intervals with one set of batteries. This allows for studies over an extended period of time (e.g. two daily profiles over a time of 3 months). The Gotland Deep Environmental Sampling Station (GODESS) in the Eastern Gotland Basin of the Baltic Sea is aimed at investigations of redoxcline dynamics. The described system can be readily adapted to other research foci by changing the profiling instrumentation platform and its payload.

322-R2U2 Engineering Assessment - August 2015

DOE Office of Scientific and Technical Information (OSTI.GOV)

Abri, M.; Griffin, D.

This Engineering Assessment and Certification of Integrity of retention tank system 322-R2 has been prepared for tank systems that store and neutralizes hazardous waste and have secondary containment. The regulations require that this assessment be completed periodically and certified by an independent, qualified, California-registered professional engineer. Abri Environmental Engineering performed an inspection of the 322-R2 Tank system at the Lawrence Livermore National Laboratory (LLNL) in Livermore, CA. Mr. William W. Moore, P.E., conducted this inspection on March 16, 2015. Mr. Moore is a California Registered Civil Engineer, with extensive experience in civil engineering, and hazardous waste management.

Near-inertial Wave Studies Using Historical Mooring Records and a High-Resolution General Circulation Model

DTIC Science & Technology

2009-09-30

Mooring Records and a High- Resolution General Circulation Model Harper Simmons School of Fisheries and Ocean Sciences 903 Koyukuk Drive Fairbanks AK...oceanographic community has been to develop a global internal wave prediction system analogous to those already in place for surface waves. Early steps have... Fisheries and Ocean Sciences,903 Koyukuk Drive,Fairbanks,AK,99775 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND

Mooring Analysis of the Ocean Sentinel through Field Observation and Numerical Simulation

DTIC Science & Technology

2013-11-22

DAS controls the Ocean Sentinel’s three power systems: a diesel generator, a wind turbine , and two solar panels. The DAS monitors sensors that detect...or floating wind turbines . A summary of different mooring configurations and their characteristics is shown in Table 2. 10 Figure 10...Table 3. Secondary wind speed and direction are measured with a Gill Windsonic Wind Sensor , which uses ultrasonic transmissions to calculate wind

A sound budget for the southeastern Bering Sea: measuring wind, rainfall, shipping, and other sources of underwater sound.

PubMed

Nystuen, Jeffrey A; Moore, Sue E; Stabeno, Phyllis J

2010-07-01

Ambient sound in the ocean contains quantifiable information about the marine environment. A passive aquatic listener (PAL) was deployed at a long-term mooring site in the southeastern Bering Sea from 27 April through 28 September 2004. This was a chain mooring with lots of clanking. However, the sampling strategy of the PAL filtered through this noise and allowed the background sound field to be quantified for natural signals. Distinctive signals include the sound from wind, drizzle and rain. These sources dominate the sound budget and their intensity can be used to quantify wind speed and rainfall rate. The wind speed measurement has an accuracy of +/-0.4 m s(-1) when compared to a buoy-mounted anemometer. The rainfall rate measurement is consistent with a land-based measurement in the Aleutian chain at Cold Bay, AK (170 km south of the mooring location). Other identifiable sounds include ships and short transient tones. The PAL was designed to reject transients in the range important for quantification of wind speed and rainfall, but serendipitously recorded peaks in the sound spectrum between 200 Hz and 3 kHz. Some of these tones are consistent with whale calls, but most are apparently associated with mooring self-noise.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moore, Murray E.

The Los Alamos RP-SVS Radiation Protection Services group designed and constructed a drop tower facility for TA- 55 support work. The drop mechanism was supplied by the Lansmont company in Monterey CA. Los Alamos staffers Murray Moore and Yong Tao have noticed that the system is not dropping loads correctly, and they have photographed aspects of the PDT- 80 model system. The first 10 photos show the platen loaded with a cylindrical steel bar. The next 10 photos are of the roller-cam mechanism in the drop tower, and the last 2 photos indicate the amount of looseness in the platenmore » when it is being pulled by a person.« less

Diagnosis: Michael Moore--media paint filmmaker to be health care system's main problem.

PubMed

Kao, Caroline

2008-01-01

The media reporting on Sicko, Michael Moore's documentary about the failures of the U.S. health care system, provides an example of how corporate media continue to twist and restrict the much-needed debate on health care reform. Aside from an occasional concession that having 46 million uninsured Americans is indeed problematic, the media's hype-filled conversation on health care avoids the issues and echoes old myths about the dangers of "government-run" and "socialized" health care. But in the face of the media demonization, universal health care is remarkably popular among the public.

Design and performance of a horizontal mooring for upper-ocean research

USGS Publications Warehouse

Grosenbaugh, Mark; Anderson, Steven; Trask, Richard; Gobat, Jason; Paul, Walter; Butman, Bradford; Weller, Robert

2002-01-01

This paper describes the design and performance of a two-dimensional moored array for sampling horizontal variability in the upper ocean. The mooring was deployed in Massachusetts Bay in a water depth of 84 m for the purpose of measuring the horizontal structure of internal waves. The mooring was instrumented with three acoustic current meters (ACMs) spaced along a 170-m horizontal cable that was stretched between two subsurface buoys 20 m below the sea surface. Five 25-m-long vertical instrument strings were suspended from the horizontal cable. A bottom-mounted acoustic Doppler current profiler (ADCP) was deployed nearby to measure the current velocity throughout the water column. Pressure sensors mounted on the subsurface buoys and the vertical instrument strings were used to measure the vertical displacements of the array in response to the currents. Measurements from the ACMs and the ADCP were used to construct time-dependent, two-dimensional current fields. The current fields were used as input to a numerical model that calculated the deformation of the array with respect to the nominal zero-current configuration. Comparison of the calculated vertical offsets of the downstream subsurface buoy and downstream vertical instrument string with the pressure measurements were used to verify the numerical code. These results were then used to estimate total deformation of the array due to the passage of the internal waves. Based on the analysis of the three internal wave events with the highest measured vertical offsets, it is concluded that the geometry of the main structure (horizontal cable and anchor legs) was kept to within ±2.0 m, and the geometry of the vertical instrument strings was kept to within ±4.0 m except for one instance when the current velocity reached 0.88 m s−1.

33 CFR 127.103 - Piers and wharves.

Code of Federal Regulations, 2014 CFR

2014-07-01

... facility handling LNG is in a region subject to earthquakes, the piers and wharves must be designed to resist earthquake forces. (b) Substructures, except moorings and breasting dolphins, that support or are...

33 CFR 127.103 - Piers and wharves.

Code of Federal Regulations, 2012 CFR

2012-07-01

... facility handling LNG is in a region subject to earthquakes, the piers and wharves must be designed to resist earthquake forces. (b) Substructures, except moorings and breasting dolphins, that support or are...

33 CFR 127.103 - Piers and wharves.

Code of Federal Regulations, 2010 CFR

2010-07-01

... facility handling LNG is in a region subject to earthquakes, the piers and wharves must be designed to resist earthquake forces. (b) Substructures, except moorings and breasting dolphins, that support or are...

33 CFR 127.103 - Piers and wharves.

Code of Federal Regulations, 2011 CFR

2011-07-01

... facility handling LNG is in a region subject to earthquakes, the piers and wharves must be designed to resist earthquake forces. (b) Substructures, except moorings and breasting dolphins, that support or are...

33 CFR 127.103 - Piers and wharves.

Code of Federal Regulations, 2013 CFR

2013-07-01

... facility handling LNG is in a region subject to earthquakes, the piers and wharves must be designed to resist earthquake forces. (b) Substructures, except moorings and breasting dolphins, that support or are...

Will Moores law be sufficient?

DOE Office of Scientific and Technical Information (OSTI.GOV)

DeBenedictis, Erik P.

2004-07-01

It seems well understood that supercomputer simulation is an enabler for scientific discoveries, weapons, and other activities of value to society. It also seems widely believed that Moore's Law will make progressively more powerful supercomputers over time and thus enable more of these contributions. This paper seeks to add detail to these arguments, revealing them to be generally correct but not a smooth and effortless progression. This paper will review some key problems that can be solved with supercomputer simulation, showing that more powerful supercomputers will be useful up to a very high yet finite limit of around 1021 FLOPSmore » (1 Zettaflops) . The review will also show the basic nature of these extreme problems. This paper will review work by others showing that the theoretical maximum supercomputer power is very high indeed, but will explain how a straightforward extrapolation of Moore's Law will lead to technological maturity in a few decades. The power of a supercomputer at the maturity of Moore's Law will be very high by today's standards at 1016-1019 FLOPS (100 Petaflops to 10 Exaflops), depending on architecture, but distinctly below the level required for the most ambitious applications. Having established that Moore's Law will not be that last word in supercomputing, this paper will explore the nearer term issue of what a supercomputer will look like at maturity of Moore's Law. Our approach will quantify the maximum performance as permitted by the laws of physics for extension of current technology and then find a design that approaches this limit closely. We study a 'multi-architecture' for supercomputers that combines a microprocessor with other 'advanced' concepts and find it can reach the limits as well. This approach should be quite viable in the future because the microprocessor would provide compatibility with existing codes and programming styles while the 'advanced' features would provide a boost to the limits of performance.« less

Transactional Distance in a Blended Learning Environment

ERIC Educational Resources Information Center

Dron, Jon; Seidel, Catharine; Litten, Gabrielle

2004-01-01

This paper presents a case study that describes and discusses the problems encountered during the design and implementation of a blended learning course, largely taught online through a web-based learning environment. Based on Moore's theory of transactional distance, the course was explicitly designed to have dialogue at its heart. However, the…

Evidence for the Maintenance of Slowly Varying Equatorial Currents by Intraseasonal Variability

NASA Astrophysics Data System (ADS)

Greatbatch, Richard J.; Claus, Martin; Brandt, Peter; Matthießen, Jan-Dirk; Tuchen, Franz Philip; Ascani, François; Dengler, Marcus; Toole, John; Roth, Christina; Farrar, J. Thomas

2018-02-01

Recent evidence from mooring data in the equatorial Atlantic reveals that semiannual and longer time scale ocean current variability is close to being resonant with equatorial basin modes. Here we show that intraseasonal variability, with time scales of tens of days, provides the energy to maintain these resonant basin modes against dissipation. The mechanism is analogous to that by which storm systems in the atmosphere act to maintain the atmospheric jet stream. We demonstrate the mechanism using an idealized model setup that exhibits equatorial deep jets. The results are supported by direct analysis of available mooring data from the equatorial Atlantic Ocean covering a depth range of several thousand meters. The analysis of the mooring data suggests that the same mechanism also helps maintain the seasonal variability.

Multi-faceted monitoring of estuarine turbidity and particulate matter provenance: Case study from Salem Harbor, USA.

PubMed

Hubeny, J Bradford; Kenney, Melanie; Warren, Barbara; Louisos, Jeremy

2017-01-01

Turbidity is a water quality parameter that is known to adversely affect aquatic systems, however the causes of turbid water are often elusive. We present results of a study designed to constrain the source of particulate matter in a coastal embayment that has suffered from increased turbidity over past decades. Our approach utilized monitoring buoys to quantify turbidity at high temporal resolution complemented by geochemical isotope analysis of suspended sediment samples and meteorological data. Results reveal a complex system in which multiple sources are associated with particulate matter. Weight of evidence demonstrates that phytoplankton productivity in the water column, however, is the dominant source of particulate matter associated with elevated turbidity in Salem Harbor, Massachusetts. Allochthonous matter from the watershed was observed to mix into the pool of suspended particulate matter near river mouths, especially in spring and summer. Resuspension of harbor surface sediments likely provides additional particulates in the regions of boat moorings, especially during summer when recreational boats are attached to moorings. Our approach allows us to constrain the causes of turbidity events in this embayment, is helping with conservation efforts of environmental quality in the region, and can be used as a template for other locations. Copyright © 2016 Elsevier B.V. All rights reserved.

Biomimetic Production of Hydrogen

NASA Astrophysics Data System (ADS)

Gust, Devens

2004-03-01

The basic reaction for hydrogen generation is formation of molecular hydrogen from two electrons and two protons. Although there are many possible sources for the protons and electrons, and a variety of mechanisms for providing the requisite energy for hydrogen synthesis, the most abundant and readily available source of protons and electrons is water, and the most attractive source of energy for powering the process is sunlight. Not surprisingly, living systems have evolved to take advantage of these sources for materials and energy. Thus, biology provides paradigms for carrying out the reactions necessary for hydrogen production. Photosynthesis in green plants uses sunlight as the source of energy for the oxidation of water to give molecular oxygen, protons, and reduction potential. Some photosynthetic organisms are capable of using this reduction potential, in the form of the reduced redox protein ferredoxin, to reduce protons and produce molecular hydrogen via the action of an hydrogenase enzyme. A variety of other organisms metabolize the reduced carbon compounds that are ultimately the major products of photosynthesis to produce molecular hydrogen. These facts suggest that it might be possible to use light energy to make molecular hydrogen via biomimetic constructs that employ principles similar to those used by natural organisms, or perhaps with hybrid "bionic" systems that combine biomimetic materials with natural enzymes. It is now possible to construct artificial photosynthetic systems that mimic some of the major steps in the natural process.(1) Artificial antennas based on porphyrins, carotenoids and other chromophores absorb light at various wavelengths in the solar spectrum and transfer the harvested excitation energy to artificial photosynthetic reaction centers.(2) In these centers, photoinduced electron transfer uses the energy from light to move an electron from a donor to an acceptor moiety, generating a high-energy charge-separated state. Subsequent electron transfer reactions further separate the electron and hole spatially, reducing the electronic coupling, slowing charge recombination, and lengthening the useful lifetime of the charge separation.(3) Still following the example of natural bacterial photosynthesis, these artificial reaction centers may be inserted into the lipid bilayer membranes of liposomes. There, they are used to power transmembrane proton pumps based on a redox loop that employs a lipid-soluble quinone molecule to shuttle hydrogen ions across the membrane, acidifying the interior of the liposome.(4) Finally, ATP synthase isolated from spinach can be inserted into the liposomal bilayer. Protons flow out of the liposome through the enzyme, driven by the gradient produced by the proton pump. The energy released is used to convert adenosine diphosphate into adenosine triphosphate, which is a major biological energy currency.(5) The chromophores used in these artificial photosynthetic reaction centers may also be attached to wide band gap nanoparticulate semiconductor electrodes, where their excited states inject electrons into the semiconductor, generating the radical cation of the chromophore. Such electrodes have been incorporated into a photoelectrochemical biofuel cell.(6) In the cell, NADH reduces the radical cation, regenerating the chromophore and ultimately producing NAD+. The NAD+ is recycled by converting it back to NADH via dehydrogenase enzymes that oxidize carbohydrates and similar reduced carbon compounds, including glucose, ethanol and methanol. Addition of a suitable cathode produces a cell that generates electric current through the combined action of light and enzymatic oxidation. The two examples of artificial photosynthesis discussed above are potential sources of the reducing power necessary for hydrogen production. A biomimetic approach to this goal is to couple an artificial photosynthetic system to an enzymatic system for hydrogen production isolated from a suitable organism. Some possible approaches to achieving this will be discussed. References (1) Gust, D.; Moore, T. A.; Moore, A. L. "Mimicking photosynthetic solar energy transduction," Acc. Chem. Res. 2001, 34, 40-48. (2) Kodis, G.; Liddell, P. A.; de la Garza, L.; Clausen, P. C.; Lindsey, J. S.; Moore, A. L.; Moore, T. A.; Gust, D. "Efficient energy transfer and electron transfer in an artificial photosynthetic antenna-reaction center complex," J. Phys. Chem. A 2002, 106, 2036-2048. (3) Liddell, P. A.; Kuciauskas, D.; Sumida, J. P.; Nash, B.; Nguyen, D.; Moore, A. L.; Moore, T. A.; Gust, D. "Photoinduced charge separation and charge recombination to a triplet state in a carotene-porphyrin-fullerene triad," J. Am. Chem. Soc. 1997, 119, 1400-1405. (4) Steinberg-Yfrach, G.; Liddell, P. A.; Hung, S.-C.; Moore, A. L.; Gust, D.; Moore, T. A. "Artificial photosynthetic reaction centers in liposomes: Photochemical generation of transmembrane proton potential," Nature 1997, 385, 239-241. (5) Steinberg-Yfrach, G.; Rigaud, J.-L.; Durantini, E. N.; Moore, A. L.; Gust, D.; Moore, T. A. "Light-driven production of ATP catalyzed by F0F1-ATP synthase in an artificial photosynthetic membrane," Nature 1998, 392, 479-482. (6) de la Garza, L.; Jeong, G.; Liddell, P. A.; Sotomura, T.; Moore, T. A.; Moore, A. L.; Gust, D. "Enzyme-based photoelectrochemical biofuel cell," J. Phys. Chem. B 2003, 107, 10252-10260.

Effects of single moor baths on physiological stress response and psychological state: a pilot study

NASA Astrophysics Data System (ADS)

Stier-Jarmer, M.; Frisch, D.; Oberhauser, C.; Immich, G.; Kirschneck, M.; Schuh, A.

2017-11-01

Moor mud applications in the form of packs and baths are widely used therapeutically as part of balneotherapy. They are commonly given as therapy for musculoskeletal disorders, with their thermo-physical effects being furthest studied. Moor baths are one of the key therapeutic elements in our recently developed and evaluated 3-week prevention program for subjects with high stress level and increased risk of developing a burnout syndrome. An embedded pilot study add-on to this core project was carried out to assess the relaxing effect of a single moor bath. During the prevention program, 78 participants received a total of seven moor applications, each consisting of a moor bath (42 °C, 20 min, given between 02:30 and 05:20 p.m.) followed by resting period (20 min). Before and after the first moor application in week 1, and the penultimate moor application in week 3, salivary cortisol was collected, blood pressure and heart rate were measured, and mood state (Multidimensional Mood State Questionnaire) was assessed. A Friedman test of differences among repeated measures was conducted. Post hoc analyses were performed using the Wilcoxon signed-rank test. A significant decrease in salivary cortisol concentration was seen between pre- and post-moor bath in week 1 ( Z = -3.355, p = 0.0008). A non-significant decrease was seen between pre- and post-moor bath in week 3. Mood state improved significantly after both moor baths. This pilot study has provided initial evidence on the stress-relieving effects of single moor baths, which can be a sensible and recommendable therapeutic element of multimodal stress-reducing prevention programs. The full potential of moor baths still needs to be validated. A randomized controlled trial should be conducted comparing this balneo-therapeutic approach against other types of stress reduction interventions.

Shock Compression Chemistry in Materials Synthesis and Processing

DTIC Science & Technology

1984-12-21

Moore at Los Alamos Scientific Laboratory [Schmidt, Moore, and Shaner, 1983; Schmidt, Moore, Schiferl , and Shaner, 1983]. More speculative, but also...Synthesis and Processing, March 28-29, Seattle, Washington. Schmidt, S. C., D. S. Moore, D. Schiferl , and J. W. Shaner. 1983. Backward stimulated Raman

Altered fish community and feeding behaviour in close proximity to boat moorings in an urban estuary.

PubMed

Lanham, Brendan S; Vergés, Adriana; Hedge, Luke H; Johnston, Emma L; Poore, Alistair G B

2018-04-01

Coastal urbanization has led to large-scale transformation of estuaries, with artificial structures now commonplace. Boat moorings are known to reduce seagrass cover, but little is known about their effect on fish communities. We used underwater video to quantify abundance, diversity, composition and feeding behaviour of fish assemblages on two scales: with increasing distance from moorings on fine scales, and among locations where moorings were present or absent. Fish were less abundant in close proximity to boat moorings, and the species composition varied on fine scales, leading to lower predation pressure near moorings. There was no relationship at the location with seagrass. On larger scales, we detected no differences in abundance or community composition among locations where moorings were present or absent. These findings show a clear impact of moorings on fish and highlight the importance of fine-scale assessments over location-scale comparisons in the detection of the effects of artificial structures. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ep45_Digital Space

NASA Image and Video Library

2018-04-18

Gary Jordan (Host): Houston, we have a podcast. Welcome to the official podcast of the NASA Johnson Space Center, episode 45, "Digital Space". I'm Gary Jordan, and I'll be your host today. So, in this podcast, we bring in the experts, NASA scientists, engineers, astronauts, sometimes our leaders. We bring them right here on the show to tell you about all the cool stuff that's going on right here at NASA. So, today, we're talking about data and information in space and here at the Johnson Space Center with Annette Moore. She's the Director of our Information Resources Director and the Chief Information Officer here in Houston. And, we had a great discussion about the tech we use for human spaceflight operations, including space station imagery and how it's changed over time. And then, how the Johnson Space Center is handling the multiple petabytes of data. It's actually unbelievable how much data we have. The multiple petabytes of data and information that we use all the time in our everyday lives. So, with no further delay, let's go light speed and jump right ahead to our talk with Ms. Annette Moore. Enjoy. [ Music ] Annette Moore: T minus five seconds and counting. Mark. [ Inaudible Comment ] Annette Moore: Houston, we have a podcast. [ Music ] Host: All right. Annette, thank you so much for coming on the podcast today to talk about this digital space. Annette Moore: Well, I'm pretty excited about this, and I'm glad I had the opportunity to sit down and talk with you. Host: Absolutely. And, it's, I'm particularly excited about it because we're talking about data, that not only we deal with every day, but was we were, we were just chatting just a little bit before this. There's a whole history of data, and we have, you know, we have records of all of the history of our flights that we have to maintain to a certain level, and we are required to maintain in a way that is going to, I guess, we're going to pass forth and make sure that we can retain for years to come. Annette Moore: Absolutely. Yeah. Host: There's a lot of stuff here. Annette Moore: Yeah. Host: And, we're talking about data from, from some of the Legacy programs, too, right? Annette Moore: You bet. Host: We're talking about Apollo, Gemini. Annette Moore: Apollo, Gemini. You bet. Yes, yes. Host: Wow. So, why don't we start, start with that? Why don't we start with some of the data that we're, that we're dealing with? Kind of continuing from the conversation that we were talking about earlier. What is some of the historical data that we have, and how are we keeping it? Annette Moore: So, we have data that dates all the way back to the Apollo program, and that data is kept in various forms of media. So, originally, you might imagine when we first started getting that data, that data was on paper. It was on tape. And, I mean the old fashioned, reel-to-reel tape. And, as we've moved more into the digital age, we're converting that to digital. Of course, NARA has, which is the National Archives, they have certain requirements for how they will receive data, how long data has to be retained at the federal agency. So, we have retention schedules. And so, we follow those retention schedule for when a program ends and how long we actually keep that data at the center. And then, it transfers over to NARA. But, again, as I said, NARA has some stringent requirements on how they will or will not except that data. So, we are certainly abiding by those requirements from NARA, the retention schedule and the media in which we store that data and send that data to NARA. But, it is a plethora of history, a plethora of data and information, and it tells an incredible story of NASA and the space program. Annette Moore: Yeah, a lot of the things that you see on documentaries, you know. And, I'm imagining is you have to, you have to sort of cradle the data, take care of it, raise it to be. Annette Moore: Absolutely. Host: I guess what NARA is requiring it to be. Annette Moore: Yeah, absolutely. Host: And then, send it off into the world to. Annette Moore: Yeah, yeah. Host: I guess, I guess explore and be used. Annette Moore: Yeah. Well, we value that data very much. We have some of that data in the form of oral history where folks have actually interviewed folks from the old programs, and they have a wealth of information and data that they share. And, that data is not just used for the purposes of memorable content, but it's actually used to inform some of our programs moving forward. Host: Yeah. And, talking about data, just, the landscape where we are now, we're dealing with just insane amount of data. Yeah, and you're talking multiple petabytes. Annette Moore: Yeah. Host: You were talking before. Annette Moore: Yeah. Host: Just billions. It's. Annette Moore: Billions and billions of data. Yeah. Host: It's incredible. So, let's, I guess, start from the beginning and see how we got to this point. How did we get so much data? What were we dealing with, what were some of the legacy technology and information that we were dealing with, and the start of the space program? Annette Moore: So, you know, it's really interesting because I'm going to kind of date myself here. So, I started back in the shuttle day, and I can remember working over in building 30. And, pretty much like, and I wasn't, I wasn't this far dated back. But, when you go to the bank, and you have the pneumatic tubes that they send your money through, through the teller. You know, that actually started as far back as that, you know, in terms of how you transmitted the data. Now, we transmit the data over network lines. We transmit the data via station coming downlinked to the Mission Control. We transmit the data in various forms. We receive the data in various forms. We analyze the data, and then we store the data in various forms. And so, that dates all the way back to the beginning of the shuttle program, all the way back to the beginning of the Apollo era, all the way back to when we were looking at data and deciphering that data and deciding how we needed to store that data, what we needed with that data. And, what data was important and what data wasn't. I think back then, everything was data. We kept everything. We stored everything. When programs expire, they're supposed to actually bring those, that data current and put that data in a format and a form that can go to NARA. We have boxes and boxes of data over, and our archivist is storing that data when a program ends. And so, I've been across several of the centers, and I'm just astounded by the data that they have that they're collecting and that they're storing. So, that's something that we're known for. That's part of our legacy. And, I think it's a great legacy that we have. Host: Yeah. Annette Moore: Yeah. Host: That's, well, the history is phenomenal. Annette Moore: The history is, it's phenomenal. It is. Yeah. Host: So, when you're talking about different kinds of data, going back to those tube days, the pneumatic tubes. You're not talking about information that's stored electronically. You're talking about. Annette Moore: That's right. Host: Physical copies of data that have to be. Annette Moore: That's absolutely right. Host: Physically filed away. Annette Moore: That's absolutely right. I'll tell you, that's true even in our medical profession. Think about when you used to go to that, again, I'm going to age myself. When you, you know, I'd go to the dentist's office, and they'd role out the file cabinet, you know. They'd have the tall file cabinets, and they literally would have a rotary. And, they would roll out, and that's how they stored data. That data now, because there are government requirements now to go to an electronic format for that data. And so, we've moved into that age. We weren't always there. We've moved into that age but think about the cycles of individuals that it takes, the cycles of time, the cycles of transferring across the age of technology to convert that data into a format that is now usable in this current age. So, we've gone through quite a transition with the data. Host: Now, there was, there was a lot of data in our history, too, and, you know, file cabinets, right? You're rolling stuff out. But, not only that, even the technology that was digital. Annette Moore: That's right. Host: Took up a lot of space. Annette Moore: Took up a lot of space. It did. You know, I can remember in my early days of program, and we had the big, round discs that had all of the data for your program files that you would store. It's quite different, and now, you have, what, a little disc that you pop in. You have a little thumb drive that you pop in. Host: Yeah. Annette Moore: But, that actually has tons of data on it as well. Host: But, that's just because of how technology has progressed. Now. Annette Moore: Absolutely. Host: What used to take an entire room, maybe even a floor, we can go back to store the amount of data that you can now store on a thumb drive. Annette Moore: Yes, absolutely. Absolutely. You bet. Host: Now, I'm thinking about Mission Control. This is always one of my, one of my just, I'm blown away by this statistic is the comparison of the data that Mission Control was dealing with versus what a current smartphone can deal with. Annette Moore: Yeah. [laughs] Host: Is it true a smartphone can actually compute more? Annette Moore: That's absolutely true. Back in the Apollo era, that is absolutely true. You bet. Yeah. Host: Wow. Because you were dealing with kilobytes of data, right? Annette Moore: You bet. You bet. Host: Unbelievable. Annette Moore: Yeah, that is. Host: How did that, how did, how can you fly a rocket, how can you communicate a deal with space systems with such little data? It, I mean, why can I not fly a rocket with my phone right now? [ Laughter ] Annette Moore: Well, technology has advanced over time. What we have done with that technology has also changed over time. And, I think our goals and our objectives and where we were trying to get, that's changed over time. And so, with that, all of the things that are associated with it, not just the technology, but the smarts that it takes to do that. That's changed over time. How we test has changed. How we prepare for flight readiness has changed. And so, all of that with that, that advancement of technology has been very necessary. I always tell people NASA hires smart people, and they absolutely do. I look back in the John Glenn day, and I look at what those guys were doing and what they were computing in their heads, what they were computing with pen and paper and how we do it very differently now. But, it's still the same, math is math, yeah. Host: That's true. Yeah, we just have a lot more, I guess, computer help. Annette Moore: We have a lot more computer help. We absolutely do. Host: Yeah. Annette Moore: Yeah. Host: So, the processes of just working in Mission Control, working here and dealing with data. Now, you're talking about converting from a time of you're doing math with hand. Annette Moore: With hand. Host: And, a pen, on your desk, and just dealing with all of the computer. How have you seen the workplace shift over time or know about the shift over time between just dealing with more and more data? Annette Moore: So, it's shift everywhere from the physical construct of the work environment to what's necessary, the tools that are necessary for you to do your job, to the whole thought process behind how you do your job. That has shift. If you look back into even how we were simulated in our work environment, how we work closely together in big rooms where information was being shared. You share information. I share information across the continent to other folks. I share information across to other centers that are on opposite ends of the spectrum from me. So, you share information, and you look at how you do that and how we had to do it once. And, it really composites setting with everyone in the same place at the same time. But, now, technology affords us an allows us to share that information across the globe. I mean, that's phenomenal to me. You know, I think that's how we learn, and that's what we've learned so well. Host: It is, I consider it a fortunate thing that we can access so much information so readily. But, at the same time, sometimes I just want to shut off my phone. Annette Moore: I know. Host: And, just ignore [inaudible]. Annette Moore: I know, yeah. Host: We are very connected. Annette Moore: Yes. Host: Almost too connected. Annette Moore: Well, you know, that, so that's interesting that you say that because the conundrum associated with that is you're concerned then, what about the security of that data that I'm sharing. Host: Yeah. Annette Moore: That becomes a huge concern, and certainly, in my environment, in the CIO environment, in the IT world, you hear it every day. You hear about breeches and compromises. So, we used to be concerned about the device and making sure that the device is secure. What you're really concerned about, and it's a conversation we're having right now, is the data that's on that device. You want to make sure that that data is secure. So, that's huge. Host: Yeah. Because the kinds of data we [inaudible], and we should probably clarify this, is there's so much data, but it's pretty diverse, too. You know. Annette Moore: It is. Host: We're dealing with just regular math equations, like we were saying before, but then, also, there's sensitive aspect to it. Annette Moore: Yeah. You bet you. Host: There's stuff that is preliminary that can be, there's certain sensitivities that you have to protect. Annette Moore: Absolutely. You have scientific data. You have engineering data. You have health data. You have PII data. Very sensitive data at very different levels of that data. You have data that's associated with flight equipment and flight hardware. You have software, and so, yes, it has to be protected, and it has to be protected at different levels. Host: Now, we as a federal agency, I'm sure, have much more restrictions on these kinds of things. Annette Moore: Absolutely. Host: So, what's the environment on what we do to protect this data? Annette Moore: Absolutely. So, we have requirements that all federal agencies are accountable to through OMB, through NIS. Cybersecurity related requirements that require us to secure the data, to protect the data. Now, it's interesting because, as a federal agency, one of the things that NASA has to do is to share that data. That is publicly available data, and so we share that data. We have a Space Act agreement that talks about the sharing of that data with the public, but we also have a requirement and a responsibility to protect that data. And so, with that comes a lot of requirements. Currently, I will tell you at the agency level, through the Office of the CIO, Department of Homeland Security, and it's not just for NASA. It's for all federal agencies. They're providing tools and capabilities that enable us to store that data, to secure that data, and to ensure the security and the protection of that data. Host: And, what's, I guess, unique about this, and you kind of eluded to this before was you're protecting the data that you have, because it's your data, right? But, in order to operate, because we are, we're not just NASA. We are partnered with international. Annette Moore: Absolutely. Host: You know, we're partnered with nations across the globe. Annette Moore: Yes. Host: And, you're right, we have to share this information. So, how do you ensure that we can share what we need to share but that we're going to stay protected, and we're not going to have some sort of incident where people are going to be exposed? Annette Moore: So, they have the same requirements levied on them, and I can assure you they have the same concerns that we have ensure that they share the right information, that they share the right data, and that they protect the data that they share. And so, through our IT security program here at the Johnson Space Center, we're accountable to the OCI, or the Office of the CIO at the agency level. We're accountable to external entities such as Department of Homeland Security, Office of Management and Budget. There are requirements that are levied on us for our cybersecurity program. And, at the center here, through my office, we have a cybersecurity office that's actually our IT security office. With each organization here at the Johnson Space Center, you have representatives within those directorates that are responsible for the security of the systems and the data within their organization. And so, that accountability goes across the board. So, cybersecurity is a responsibility of everyone. That's everyone's responsibility. In your work environment as well as in your home environment. Host: You're right, because ultimately, it's your data, and you might not be a person who's a technical person to deal with it, but ultimately, it's your data that you're responsible for. So, you have to make sure that it's protects, and you're constantly thinking about, am I protected. Annette Moore: Yes. Host: Yeah. Annette Moore: Yes. Host: So, you're talking about requirements, and you're talking about, from the federal level, these restrictions being imposed. What are some of the things that we are required to do? What are some of the, give me an example of a requirement. Annette Moore: Right. Host: That may be, maybe is more difficult to do business. But, is essentially to make sure that we are protected. Annette Moore: So, every system that we have here at the Johnson Space Center has to be under security plan. And, it has to have the authority to operate. So, as the Center's CIO and as the authorizing official for some of those systems, I have to say that that system has the authority to operate. Well, that system has to meet certain requirements. It has to make sure that it has patching. There is scanning and vulnerability testing that's done on those systems, and if any of that is not successful, there has to be a plan of action and milestones and a mitigation plan and strategy to make sure that those systems are healthy. Or, those systems should not be connected to our network. That's a requirement for every system on this Center. And so, when I sign my name to a system as authorizing official, I'm saying that that system is healthy, it does not put the Center at risk, it does not put us in a situation of possible vulnerability occurring with that system. And, I'm signing off on that, as are the other authorizing officials for systems here at the Center. That's a requirement, not just for NASA, but for other federal agencies for their systems. The PIV implementation that we're doing right now, that's securing access to your devices, to your computer, and making sure that where you're going on the network, you have authority, and you have the right to access those systems and that data on those systems. Host: So, that's the, that's the badges that we carry around. Annette Moore: That's the badges. Host: That identify us, but then also say I am Gary, and I can access this computer. Annette Moore: Absolutely. You bet. Host: On the available access that's on this chip. Annette Moore: You bet. Host: Okay. Annette Moore: Yeah. Host: And so, basically, you're saying that all of these, all of these systems are carefully watched, and if some, and they are scanned. Annette Moore: Yes. Host: And, if something is revealed to say there is a vulnerability, there's a chance that something bad could happen, you make a plan of action to go fix it. Annette Moore: Absolutely. Host: Okay. Annette Moore: Absolutely. We don't want things connected to our network that could put us at risk. So, we have critical mission data. We have sensitive human health and performance data. We don't want anything on our systems, in our data, that could put us at risk or that could put our crew at risk or the vehicle at risk. Host: Do you see a lot of instances of folks trying to hack us, trying to, trying to get into our systems and, just you realize, because you understand probably the scope more than any of us. You know, we're sitting pretty. We're on our email. We're doing our thing, but you're saying maybe there's a side to this where we are being attacked. And, maybe we just don't know it, but our security is good enough where we don't know it. Annette Moore: Yeah. Yeah. I think you should always assume that your best posture is to be a posture where you're secured, and you're protected. I think everyone should always assume. I assume that at home with my home computer. You know, I don't click on links. I don't download things that are not credible. I assume that on my home system, I assume that on my work systems. We all should at all times. I mean, I'm not sure about you, but I've gotten a letter or two from LPM about my data being compromised because of a store that I've shopped at and my credit card number got out, as did other folks. I've been in that situation before. I just recently sent one of my siblings a text message. I said, "Hey, I know you were shopping here last month. I just saw on the new where they had a breech." I said, "You probably want to write them, and you probably want to contact your bank." I think we should always all assume that I'm going to be safe and I'm going to make sure that my systems and my data is secure. Host: Yeah. You have to be, it's kind of, you have to be constantly vigilant. Annette Moore: Yes, you do. Host: You have to be constantly aware. Annette Moore: Yes. Yes. Host: Which is kind of a burden, but also necessary. Annette Moore: It's necessary. Yeah, yeah. Host: Now, I was talking about, we were talking about requirements before, and there's obviously security requirements to make sure we're safe. But, going back, we were talking a little bit about NARA and requirements for storing data. What do we have to do to make sure that we are archiving all these great things that we're doing properly so that it could be stored properly? Like, mission videos, like when we do cool things in space and have video of it. I want to make sure that that's kept. Annette Moore: So, we have a records manager. We have each organization has someone within their directorate who is responsible for making sure that we're following the guidelines of NARA. That actually should start at the very beginning of a program, at the very beginning of a program, and it's the same way you do security. You don't do security at the end of the system. You do security at the very beginning, from cradle to grave. And, it's the same way with records retention. When you start kicking off a program, you should, then, start actually recording your records and keeping your records and keeping them according to the requirements for NARA. And so, when that program ends, you've got all your records according to how you're supposed to capture your records, record your records, save your records, file your records. You've got all of that in order. And, that's critically important. As I said, a lot of that data is used on newer programs from previous programs. I had a visit out to Wallace, actually to, I'm sorry, White Sands a couple of months ago. And, years ago, at the very beginning of my career, I worked on small ICPM missiles, and I worked at Peacekeeper and Minuteman. And, to my surprise, I walked in, and there was the missile head from Peacekeeper that I worked on years ago, early in my career. And, we're using information from that to help inform us as we move forward with our new programs such as Orion. And, I was just like, "Wow, that was at the beginning of my career. I can't believe I'm seeing this," you know. Host: Blast from the past. Annette Moore: But that shows the criticality and the importance of maintaining good records and keeping those records from the beginning of a program to the end of that program and making sure that that data and that information, then, can be passed on for future programs. Host: Yes, because it's learning. Annette Moore: It's learning. Absolutely. Host: It's learning. In order to make things better, you need to know how they were first. Annette Moore: Absolutely. Host: Yeah. Annette Moore: Yeah. Host: So, so, we have these requirements to document thing a certain way. Were these, have we captured everything successful, or are there things that we're just, we're just not going to get? Annette Moore: I think what we've done is we've learned along the way. I think we've learned and we've gotten smarter with how we have captured records, how we have retained those records, how we have stored those records. And, I think that program has improved over the years. I've seen it just in the span of time that I've been working in the office of the CIO. I've seen where we've gotten really smart. We've partnered with other organizations. We've partnered with other federal agencies. NARA is very helpful and very good at helping federal agencies [inaudible] because that is a legacy, not just of a federal agency, not just of a program. That's the legacy of our country. Host: Right. Annette Moore: Yeah. Host: Yeah. You know, they want to make sure that it's not lost. Annette Moore: They want to make sure. Yeah. Host: So, they will help us along the way to make sure. Annette Moore: They help us, yeah. Host: Okay. Annette Moore: Yeah. Host: So, so, where, yeah, make sure that we capture all this great history that we're doing. Annette Moore: Yeah. Yeah. Host: Now, I think one of the biggest challenges is it's got to be technology because what used to be maybe a little datapoints with kilobytes of information, now we're getting video. Now, we're going to HD video. Annette Moore: Yeah. Host: There's not only a different kind of data that we're dealing with, but it's larger. Annette Moore: It's larger. Host: And, we got to figure out where to put it because that's a lot of data. Annette Moore: Larger, very sophisticated. Host: Yeah. Annette Moore: Different ways to manipulate the data, different ways to manage the data and maintain the data. And so, we have to progress with the progression of the technology. We have to get smarter with the technology, and we have to really learn how to use it and leverage it to the best advantage that we can and to ensure that it provides capability that we need. Host: So, it sounds like one of the biggest challenges is going to be balance. Balance on the requirements that you have for certain technologies, but then also making sure that you're keeping up with the technology itself. Annette Moore: You bet. Absolutely. Host: So, maybe technology, and people talk about this all the time, is progressing so fast. Annette Moore: Yeah. Host: Not a lot of people can keep up with it. So, how do you write procedures and rules to make sure that we can keep up with it, at least to the best of our knowledge and capability? Annette Moore: So, one of the things that I think is hugely important is that we are staying out there ahead of the technology, or at least in sync with the technology. So, one of the things that we like to ensure that the folks on our team are doing, that they're exposed to this growth in technology, that they're partnering with other organizations outside of federal government, outside of NASA, because folks outside of federal government are, they're taking the risk that we sometimes don't take because we just don't have the opportunity to take that risk. Our schedules, our projects, our timelines, the fact that we're doing, dealing with humans in space, it maybe allows us to not take some of the risks that other folks take in terms of progressing technology. But, in partnering with those folks, benchmarking with those folks, we're learning where the technology is going. I was just at a CIO face to face last week, and we're talking about what are we going to look like three to five to ten years from now. We're not talking about what are we going to look like a year from now. We're talking about what is it going to look like three to five to ten years from now. We have to do that. Host: Yeah. Annette Moore: Yeah. Host: Now, the difficulty is you can, looking ahead, try to think three, five, ten, but then, there's so many technologies that maybe we don't even know are on the horizon. Annette Moore: We don't know. Yeah. Host: That you have to plan for. Annette Moore: Yeah. Host: That's got to be difficult. Annette Moore: Absolutely. Absolutely. Yeah. Host: I know there's just a lot of challenges with dealing with this data, and we were talking about, we're talking about HD video, and now I know recently, we were doing 4K downlinks. Where, now, we're dealing with 4K. Annette Moore: Yeah. Host: So, one of the biggest things I'm thinking of is storage. Do we store a lot of things here on the Center? Annette Moore: We do. We have a data center here, and it's interesting. I love that you just asked me that because we just entered a wonderful partnership that I'm very proud of with Station where we moved over to a new storage content platform for them for all of the imagery that we get, the still, the video. Everything that we get that's downlinked from Station. This is data that we're getting every day. So, just imagine, just the flood of data that's coming in every day. And, we actually entered a partnership with them just last year on a content platform for their storage, and we presented a business case to them. And, this was so exciting for us because it provided us an opportunity not look at where they are just right now. But, at the rate that we're getting data from Station, and that rate is not going to slow down. We wanted to provide a storage platform for them that would allow them to look years out and continue to build on that and not have to be concerned about I'm going to run out of storage space. And so, we sat with them, and we worked with them to understand what their requirements would be, not just for today, but where they saw themselves, five, ten, years from now and built this platform for them out in our data center. And, we're very proud of that. It was a great partnership that we had with them, and we're going to continue to build on that. Host: It was very exciting. Annette Moore: Yeah. Very exciting. Yeah. Host: Now, I think, you know, you're talking about planning, planning farther ahead, even. Annette Moore: Yes. Host: With these, with these servers. So, I'm sure you're thinking of this is going to meet our capabilities for storing now, and then, going back to the requirements of we have to keep our data for. Annette Moore: Yes. Host: A certain amount of time, and then, fit it for NARA requirements. Annette Moore: Exactly. Host: I'm sure that's part of the plan, too. Annette Moore: Yes. Yes. And, part of what we look at when we look at that, as well, particularly in the subject of storage, is we look at, so, when do we move or what do we move into the cloud environment. Because, that allows us more elasticity in terms of storage capability for our data. You know, there's that security element around that as well. Host: Yeah. Annette Moore: Who owns your data? Host: Right. Annette Moore: You know, what are the requirements for your data being in the cloud? What's the cost of being in the cloud? So, those are all of the things that you have to consider, and that's certainly part of the conversation when we look at what our options are for storage. And, not just storage, but how we can securely store our data and affordably store our data. Host: It's a big balance, right? Annette Moore: It is. Host: Secure but affordability. Because you can keep it here, but then you have to buy these servers. Now, you have to have this machinery, this hardware that's going to keep everything. That can get up the costs. It's yours, and you're secure because it's not, you know it's your data. So, you got that, but then, at the same time, technology is maybe going toward the cloud, and how do we fit things into the cloud but make it still ours? I can see where there's a lot of back and forth there. Annette Moore: I love where this conversation is going because we were just talking earlier about requirements that are imposed on us at a federal level. We're a federal agency. Host: Yeah. Annette Moore: And, one of the things that we had a requirement for, and not just us NASA, but federal agencies, was to reduce our footprint for our data center. Reduce our physical footprint, the number of data centers that we have. And so, that's when you look at technologies like going to cloud and how you can enable that. Host: Wow. So, okay. So, it's actually looking at requirements to limit what we have physically, and to. Annette Moore: Absolutely. Host: Actually opt into using cloud technology. Annette Moore: Yeah. Host: That's pretty significant. Annette Moore: That is. Host: But, now, you have a whole bunch of more challenges of security and ownership and. Annette Moore: Absolutely. Host: Stuff like that that you have to deal with down the road. Annette Moore: Absolutely. Yes. Host: Lot of challenges going on. Annette Moore: Lot of challenges, but you know, I will tell you, I really see those challenges as opportunities. And, that's what I tell my team. Those challenges are really opportunities for us to move forward, you know. I want to be in control of my destiny. Host: Yeah. Annette Moore: I don't want someone to be in control of that for me. I want to be in control of that. I want to be at the table when we're talking about where this agency is going to be three, five, ten years from now, what our future looks like. That's hugely exciting. Host: It is very exciting. Now, thinking towards the future and making sure we can, we can get there, I actually am going to redivert this to the past. And, we were talking about, you know, we have data centers that have this digital technology stored in these servers. So, we can, we can house our own data here, but we have different types of data. We have, we have tapes from the Apollo days and from, and from shuttle days that we need to convert. What's that process look like? How are we doing that? How are we taking this older technology and converting it? Annette Moore: I would love to take you on a tour out to what we call our farm, because. Host: Okay. Annette Moore: We literally have the reel-to-reel tapes that I can remember as a kid. You probably can't, but I can. [ Laughter ] You know, the reel-to-reel tapes, and we are actually converting that to digital format. And so, that's happening right here on site. That's happening at other centers because other centers have that same challenge. When you think back to that era where all you had were the reel-to-reel tapes. That's all you had. So, now, you've got to convert that because some of that tape also is going through what they call the vinegar syndrome where it's deteriorating. So, that's history. That's information. You'll never recapture that if you lose that. So, you want to convert those things to their appropriate format. And, of course, that's not something that NARA would accept. If you've got film that's going through the vinegar syndrome that would not be a good storage solution for NARA with all of the responsibilities that they have for maintaining the legacy for our nation. So, we are, we have moved to technology that is allowing us to convert it. Now, here's the challenge. As you said, plethora and plethora of data. Host: Oh, so much. Annette Moore: So, the time that it takes to do that conversion, trying to do that quick and where that data is still good, and you can get it converted to that new format. Host: You're right. Because you're talking about, I mean, like, shuttle missions, for example. Annette Moore: Exactly. Host: That lasted for weeks, and you just have a continuous stream of weeks of data. Annette Moore: Absolutely. Host: That you have to convert. Annette Moore: Absolutely. Host: But, it's, I like how you're saying that it's, not only is it a requirement that we have to have it digital in order to store it with NARA, now you're talking about just saving the film itself. Annette Moore: The film itself. Yeah. Host: The film itself is going to disappear if we don't do something. Annette Moore: Absolutely. Host: So, we have to do something to save that data. Annette Moore: Absolutely. Absolutely. You know, I'm so proud that the folks in my organization understand the importance of that, the importance of that, the history that that has a legacy that that has, and that they're committed to that. And, I, when I visit the other centers, I see that same commitment to that, you know. And, it's great. Host: It's a lot of hard work. Annette Moore: Yeah, it is. Host: Because it's very monotonous labor, right? You have to, all right. Put in another film reel. Here we go. I mean, there's a lot to it, but it's vital to save that stuff. Annette Moore: And, I got to tell you, I'm going to, you want you to hold me to this. I'm going to take you on a tour out to our farm where the guys are doing that. Host: All right. Annette Moore: They understand that when they pick up that reel of film, that's history that they have in their hand. Host: Yeah. Annette Moore: I can recall getting a call from the guys out there, and they had found a reel of film that showed the original construction of Johnson Space Center. And, they were so excited. They were, "You won't believe what we came across. You won't believe what we found." You know, I mean, they had, they take great pride in doing that, and that's so cool, I think. Host: To be, I mean, to be the first person to hold that. Annette Moore: Yeah, yeah. Host: Film reel in decades. Annette Moore: Yeah. Host: That's got to feel very special. Annette Moore: Yeah. Host: And, to say, "I'm going to save this!" Annette Moore: Yeah. Host: "I'm going to be the person that going to save this." Annette Moore: Exactly, exactly. Host: "For somebody else." It's on record, though, so I'm going to hold you to it. Annette Moore: Yeah, yeah. Host: The tour. [ Laughter ] Annette Moore: You bet. You bet. Host: So, this is probably a very important question to follow up on is we're saving all this data. It's history. We're putting into the archives. What, what are some of the ways that we can use that data? Why would we save all of it versus just, eh, this is important? We don't need it. We don't need to save it. It's just going to take up space. How do you decide what's important, what's not, and why to save it? Annette Moore: So, there are certain requirements for what you have to save. NARA has some requirements on that in terms of the kinds of things you save. I'll give you an example. Even senior executives, things like their email records, that is considered a record. Think about that. Think about what's documented with our Presidents. You know, speeches that they've had, decisions that they've made, you know, law that has been enacted. There is a reason we say that it tells a story. It is our legacy. It says who we are. It informs us. It's in our textbooks. It informs us. It helps us in terms of building our future. Those are things that are vitally important to us as individuals, vitally important to us as a nation, vitally important to us on this globe. Host: Yes, yeah. So, it's, you recognize the importance. I think one of the things on my mind is immediately going to is whenever we've had, whenever we've had some of the recent accidents, right? Annette Moore: Absolutely. Host: So, like, if you're talking about the Columbia accident. Annette Moore: Absolutely. Host: Now, you have this data where you can go back. Annette Moore: Absolutely. Host: Look at every excruciating detail. Annette Moore: Absolutely. Host: Because we have it. Because you saved it. Annette Moore: Yes. Host: And, it's crucial to find out what went wrong, what can we do to fix it, what can we do to prevent it from happening in the future. Annette Moore: You can even think in everyday terms of how we study weather data. You know, so, I was impacted by Hurricane Harvey. Host: Yeah. Annette Moore: And, when I think about the studies that go behind weather and weather patterns and things that they watch for the weather, I'm very grateful for that because that alerts us, it alarms us in a way that keeps us safe. But, that's important for our survival. This data is as well. Host: Yeah. Annette Moore: The survival of our crew. Host: Exactly. It's like the more you know, the more informed decision you can make to make the best decision. Annette Moore: Absolutely. Yeah. Host: Yeah. I'm sorry to hear about Harvey. You were talking. Annette Moore: Yeah. Host: A little bit before, and you are just, it's been crazy with all the traveling. You can't even unload the boxes into the house. It's got to be brutal. Annette Moore: Yeah. Host: You know, looking at, looking at, going back to imagery, I think this is one component of your division that I think is just absolutely fascinating. Annette Moore: Yeah. It is. Host: When you're talking about the beautiful images we're getting from 250 miles above the space station, but all of the rest. What are we, what's the story there? What's the story of the whole imagery component of the division? Annette Moore: So, we have imagery online. We have, as I said, we're getting around the clock. And, I don't think people realize this, but over in building eight, we're getting around the clock downlink from Station. If it's still, if it's video, it's imagery, it's photo shots. We get imagery from test data, and when engineering directorate does test data, we get photos from that. I mean, we get this data around the clock. That's, it tells a story. Host: Yeah. Annette Moore: It absolutely does. That data is used for tests. It's used for engineering analysis. It's used for data analysis. It's used for capturing and telling the story for when the crew is onboard, and what's happening throughout their duration of their crew time. It's used for all of those things, and we keep that data. That imagery is stored. It's very important for us. It's very important for the crew. When they come back, and they've got that data from their flight, they can use that data to do analysis, to do some forward work. That's hugely important. It's hugely important for folks in the engineering directorate as they're making decisions about test data and what they need to tweak, what works, what doesn't work. Hugely important. Yeah. Host: Now, that's actually, I think, one of the coolest parts about the imagery department is you have these still photographers, and not only are they taking artistic photographs and the ones you see online, the films you see of rockets going up. But, it's not, the purpose isn't because it's pretty. Annette Moore: No. Host: The purpose is, like, they're taking close up pictures of hardware. Annette Moore: That's right. Host: They're taking photos of even the crew. Annette Moore: That's right. Host: Is grabbing a camera onboard and taking photos. Annette Moore: That's right. Host: Of things that don't really look too great, but it is vital for engineering purposes. Because it's, like what you said. I love that phrasing. It tells a story. All right. What's going on here? What's the layout? How can we fix it? There's a lot of, it's important, and not only to store but to keep track of, to organize. That must be a pain to organize all those images. Annette Moore: Yeah. Annette Moore: That, well, I think the folks who do that, I've walked through our area where we have all of our imagery, and the folks who are doing that, they love that. And, they, it's like you get to experience having been on station, and you are not really there. You get to experience it as they go through all of these photos, as they go through this still imagery, as they go through the video. They get to be a part of that experience. Host: Yeah. They're part of the story. Annette Moore: Yeah. Host: Because they're living through it, and they're, they have to organize it in their head and come up, like you said. Annette Moore: Yeah. Host: With a story. And, I think the, you hinted at this before, where they're putting it is called imagery online, right? Annette Moore: Yes, it is. Host: That's the repository, right? Annette Moore: It is. Host: That's where everything's going. And, it's just I use it all the time, but it's a place where you can search the images you need. Annette Moore: Yeah. Yeah. Host: So, I'm, you know, me being in PAO, I search the ones that are prettier. That we can put on the web and share with people. Annette Moore: Well, you know, you guys have a pretty cool, cool role. So, I was at the last [inaudible] launch, and you know that we have folks who travel there from PAO who are taking the pictures. And, they're taking the pictures of the launch absolutely. They're taking the pictures of the crew coming out, and they're in their gear, and they're getting ready to get on the bus to go over to the launch pad. Absolutely taking pictures of that, but you know what they're also taking pictures of? I watched one of our astronauts interact with the children of one of our crewmen who is going up. And, you capture that. That's nothing like that. You know, the time that he took with these kids. Their father was getting read to go up. You know, the time that he took with them, and there was someone capturing all of this. You know, that's, do you know what that will mean to them years from now when they look back at that? Host: Oh, yeah. Annette Moore: Yeah. Host: You know, I've talked with quite a few folks on the podcast, and sometimes it just comes down to a single moment. It comes down to, you know, I had one guest write a letter to NASA just say, "Hey, I'm trying to be an astronaut. What should I do?" Annette Moore: Yeah. Yeah. Host: And, they wrote back, and they sent something. Annette Moore: Yeah. Host: Back to her. Annette Moore: Yeah. Host: And, she's like, "Yes. I am so motivated." She dedicated her entire school career and career after that to eventually getting to the Center. Annette Moore: There's nothing that compares to the experience of the human element, one person to. Nothing that compares to that. And, the fact that we can capture that through photos, through imagery, through video, that we capture it in so many ways. That we capture that in the records that we keep and that we pass on from one program to another, that informs the next program and the next mission. Yeah. Host: So, how much of it do we, do we keep for these informational purposes, that we keep for the engineering purposes, for learning and making our systems better and assessing and stuff like that? But, and then, how much are we looking at historical photos and maybe current photos and then sharing them out? What are we doing to share with the public? Annette Moore: So, our imagery online. Anyone within the NASA community can get through that. We also have an agreement with U of H Clear Lake. So, we have some imagery and some things through U of H Clear Lake. So, they actually have some records as well on file. So, NASA, if you look in our Space Act agreement, you know, we're a public entity. We're not an entity unto ourselves, so we exist for the purpose of, you know, of furthering humans in exploration, in space, and in all of those avenues. And so, the data that we have is not just unto ourselves. Certainly, there is a proprietary piece of that data that is used for research, that's used for human exploration, that's used for the furtherment of other missions and other programs. But, there's also a portion of that data that we are obligated to make available to the public. There is a portion of that data for historical purposes that we're obligated through NARA to make available as well. And so, that data is not just something that we parse out amongst the NASA community, but that data is shared across all kinds of venues for various reasons. Research and development, engineering, scientific and data analysis, for the general public. You know, and that's absolutely obvious when you look at our education program and how we make information available through our education program. Host: That's interesting that they're obligated. That we, we have a requirement to share this stuff. Do you know how far back we have to go until it says, "Anything past this date, that's the [inaudible],"? Annette Moore: So, for your program, when you start your program up, NARA has what they call a retention schedule. So, that retention schedule says this data, this kind of data, you have to save. You have to archive it for this period of time. And, after that period of time, you're not obligated. So, our in building 412, we have data that we're obligated to hold on site, physically, on site until its retention date has passed. And, we have what's called retention schedules. Once it hits its retention schedule, then we can send it to NARA, but it has a requirement that you hold it. And, that's for a reason. So, when we sent something to NARA, once we sent it to NARA, we have to, then, retrieve it. So, if you have to retrieve that data because you want to study that for another program that's coming up. So, it costs us to store the data with NARA, and it also costs us to retrieve that data. Host: Oh, yeah. Annette Moore: So, we want to retain that data and hold on to it until we can get as much as we can out of the life of that data. Host: Yeah. Annette Moore: And then, we will pass that data on according to the retention schedules. So, there are requirements on the data, and it has retention schedules that NARA establishes for the data. Host: So, it's like, we're required to retain it here, and that makes sense because it's fresh data. We want to use it. We want to have ready access to it. Annette Moore: Absolutely. Host: Limit the cost of it. We want to protect it. That makes a lot of sense. And then, it comes to a certain point where you have to retain it for, like you said, this amount of time. And then, you go over to NARA, and then, I guess, when it goes to NARA, that's public record, and right? Annette Moore: Right. And so, you also have what are called permanent records. Host: Permanent. Annette Moore: There are things that are permanent records. So, that's in that movie, "Raiders of the Lost Ark". When he goes, you know, those are, that's permanent records. Those records will never be destroyed. So, yeah. Host: Wow. Annette Moore: Yeah. Host: Now, I can't even imagine the amount of data to be permanent. Annette Moore: So, on one of my next trips to D.C., I'm going to the National Archives because I want to see for myself. I've actually had friends who have gone to the National archives and researched generations and generations back in their family. Host: Wow. Annette Moore: Yeah. Host: Oh, because they, yeah, archive all of that stuff. Annette Moore: Yeah. Annette Moore: Oh, my gosh. Annette Moore: Yeah. Annette Moore: I can't even imagine. That's so, that's like a never-ending construction project. Annette Moore: Yeah, yeah. Annette Moore: To build more and more as more data comes in. And, yet, we're required to keep more data, and. Annette Moore: Yeah. Host: Data becomes larger. I'm thinking. Annette Moore: Yes, it does. Host: My media files are up to 4K video. Oh, my gosh, dealing with that is such a pain. Annette Moore: Yeah. Host: It takes forever to downlink from the Station, and then it takes forever to work with. I mean, I have a tight computer, but, man, that's a lot. I think, so, what's nice about having you here, Annette, is you oversee all of this, right? So, you oversee the imagery. You oversee the storage. You oversee. So, there's so much to IRD that you're directorate, that it's just unbelievable. And then, on top of that, you're CIO. You got a large responsibility. I think one of the biggest things, and it's selfish for me as an employee here, but you're looking at working with ASIS, right? And, end user, so my computer. Not only are you looking at the imagery from the station, you're looking at my computer. So, how does that work? How do we manage the information technology that we have at our desks? Annette Moore: So, I'm responsible for that, as you said, and I'm responsible for that through two contract vehicles. So, we have the enterprise contract vehicle which is through ASIS, NIX east and west. So, we have the enterprise model, and then I have local contract that provides some additional IT support to the Center. And so, that's managed through two different offices within IRD. The IC Office has the ASIS contract under them, and then the IB office which is my information management. And then, my multimedia office. I think you probably know Ed and his team. So, they manage those two separate contracts. And, I'm responsible for that for the Center. And, I take that very personally. You know, when someone says, "Well, my computer is, I'm having issues with my computer." I take that very personally. You know. Host: Yeah. Annette Moore: I'm responsible for that, and that means a lot to me. You know, I've, I call folks. "So, how's your computer? Did we fix it? Is everything okay? Follow back with me and let me know if you're not satisfied with." So, I'm responsible for that as the CIO and as the director of IRD. It's kind of like a Dr. Jekyll Mr. Hyde thing. So, as a Director of IRD, that's the provider of your IT services here at the Center. As the CIO, that's almost like the policing and enforcing. That's the policy piece, the oversight. And, you see how the two can, might sometime conflict. Host: Yeah. Yeah. Annette Moore: But, I take both of those roles very seriously. The customer experience is paramount for me. That's critical, so. Host: It's a lot to oversee. How do you do it? What's your background, by the way? Annette Moore: So, I'm, my undergrad is in double e, electrical engineering. Host: Okay. Annette Moore: And then, so here is a twist. My Masters is in Elementary Ed. Host: Whoa. Annette Moore: Yeah. Interesting story. So, as a freshman, my mom and I were just, she was my best friend going through school. And, when I got ready to graduate, she told me, she said, "You're going to major in electrical engineering." I'm like, "Why?" She said, "Because you'll do well in that, and you'll make good money. And, you'll just do well in that." Unfortunately, my mom passed of breast cancer my freshman semester that I was in college. That was such a hard blow for me. That was really hard. I almost did not make it through school, I'll tell you that. Host: Yeah. It must have been hard. Annette Moore: But, it taught me a lot. It taught me a lot about perseverance. It taught me a lot about what's important. It taught me a lot about people. So, the way I do this job is that I trust the people who do the job. And, I tell the folks in my organization, "I work for you. My job is to ensure that you have everything that you need to be successful. If you don't, then I have not done my job." And so, I very much see myself as a servant leader. I'm service oriented in making sure that the people at this center have everything that they need to do the mission and make sure that the mission is successful. So. Host: That's it. That, you do it, you don't do it all. You empower others to do it all. Annette Moore: Absolutely. Absolutely. Host: And, maintain that accountability and trust within the organization. Annette Moore: Absolutely. Host: Huge part of being a leader. Annette Moore: Yeah. I tell them, "You guys are the smart people in the room. Not me." [ Laughter ] And, I'm smart enough to know that. Host: And, I'm smart enough to let you be smart. Annette Moore: Absolutely. Host: There you go. All right. Well, Annette, that is such a nice overview of IRD. I feel like there's more that we can go into, but it's just hearing your passion for what you do and what you oversee, and not only that, but the people that you work with. It's truly inspiring. So, I appreciate you coming on the podcast today. Annette Moore: Oh, thank you so much. I appreciate you asking me to do this, and you've got it on record. I'm going to ask [inaudible] so I can get you out to the farm because I really want you to see this. It's pretty cool. It's cool. Host: That would be lovely. Thank you. Annette Moore: Yeah. Yeah. Thank you. [ Music ] Houston, go ahead. [inaudible] shuttle. Roger. [inaudible] Space for all mankind. Actually a huge honor to break a record like this. Not because they are easy, but because they are hard. Houston, welcome to space [echo]. Host: Hey, thanks for sticking around. So, today, we talked with Ms. Annette Moore about the data and information that we're dealing with in space and then also here in the Center at the NASA Johnson Space Center. Some of the places that we store imagery, deal with imagery, protect imagery, and data and information. And, it's actually incredible. This is episode 45 of the podcast. We are in no particular order. It's just, that's just how we keep track of everything. So, you can go back and listen other great podcasts on dealing with the space station and especially here on the Center. We actually talked a while back. I'm trying to remember which episode. I think it's episode 12, we talked with the Center Director, Ellen Ochoa about just what we do here in Houston. And, this is just a small part of what we do in Houston, and yet, it's so broad and huge. It's actually incredible. So, you can go listen to that one. I think it's called "Leading Human Space Exploration". I believe it's episode 12. Otherwise, you can listen to some of our other NASA podcasts. We have "Gravity Assist" hosted up at headquarters by Dr. Jim Green that talks about planetary science, and then we have our friends over in Ames Research Center for their podcast "NASA in Silicon Valley". They talk about the stuff that they're doing over there in California and helping us out with some of the research aboard the International Space Station. Otherwise, you can visit our social media sites, both the NASA Johnson Space Center accounts and International Space Station accounts on Facebook, Instagram, and Twitter. Use the hashtag ask NASA on your favorite platform to submit an idea. And then, we'll make sure to make it into an episode of "Houston, We Have a Podcast". So, this episode was recorded on April 18, 2018. Thanks to Alex Perryman, Kelly Humphries, Pat Ryan, Bill Stafford, and Eloisa Sidler. And, thanks again to Ms. Annette Moore for coming on the show. We'll be back next week.

The importance of deep, basinwide measurements in optimized Atlantic Meridional Overturning Circulation observing arrays

NASA Astrophysics Data System (ADS)

McCarthy, G. D.; Menary, M. B.; Mecking, J. V.; Moat, B. I.; Johns, W. E.; Andrews, M. B.; Rayner, D.; Smeed, D. A.

2017-03-01

The Atlantic Meridional Overturning Circulation (AMOC) is a key process in the global redistribution of heat. The AMOC is defined as the maximum of the overturning stream function, which typically occurs near 30°N in the North Atlantic. The RAPID mooring array has provided full-depth, basinwide, continuous estimates of this quantity since 2004. Motivated by both the need to deliver near real-time data and optimization of the array to reduce costs, we consider alternative configurations of the mooring array. Results suggest that the variability observed since 2004 could be reproduced by a single tall mooring on the western boundary and a mooring to 1500 m on the eastern boundary. We consider the potential future evolution of the AMOC in two generations of the Hadley Centre climate models and a suite of additional CMIP5 models. The modeling studies show that deep, basinwide measurements are essential to capture correctly the future decline of the AMOC. We conclude that, while a reduced array could be useful for estimates of the AMOC on subseasonal to decadal time scales as part of a near real-time data delivery system, extreme caution must be applied to avoid the potential misinterpretation or absence of a climate time scale AMOC decline that is a key motivation for the maintenance of these observations.