X-ray tomography of powder injection moulded micro parts using synchrotron radiation

NASA Astrophysics Data System (ADS)

Heldele, R.; Rath, S.; Merz, L.; Butzbach, R.; Hagelstein, M.; Haußelt, J.

2006-05-01

Powder injection moulding is one of the most promising replication methods for the mass production of metal and ceramic micro parts. The material for injection moulding, a so-called feedstock, consists of thermoplastic binder components and inorganic filler with approximately equal volume fractions. Injection moulding of the feedstock leads to a green part that can be processed to a dense metal or ceramic micro part by debinding and sintering. During the injection moulding process extremely high shear rates are applied. This promotes the separation of powder and binder leading to a particle density variation in the green part causing anisotropic shrinkage during post-processing. The knowledge of introducing density gradients and defects would consequently allow the optimization of the feedstock, the moulding parameters and the validation of a simulation tool based on the Dissipative Particle Dynamics which is currently under development, as well. To determine the particle density and defect distribution in micro parts synchrotron radiation tomography in absorption mode was used. Due to its parallel and monochromatic character a quantitative reconstruction, free of beam hardening artifacts, is possible. For the measurement, bending bars consisting of dispersed fused silica particles in a polymeric matrix were used. The presented results using this set-up show that crucial defects and density variations can be detected.

Analysis of the shrinkage at the thick plate part using response surface methodology

NASA Astrophysics Data System (ADS)

Hatta, N. M.; Azlan, M. Z.; Shayfull, Z.; Roselina, S.; Nasir, S. M.

2017-09-01

Injection moulding is well known for its manufacturing process especially in producing plastic products. To measure the final product quality, there are lots of precautions to be taken into such as parameters setting at the initial stage of the process. Sometimes, if these parameters were set up wrongly, defects may be occurred and one of the well-known defects in the injection moulding process is a shrinkage. To overcome this problem, a maximisation at the precaution stage by making an optimal adjustment on the parameter setting need to be done and this paper focuses on analysing the shrinkage by optimising the parameter at thick plate part with the help of Response Surface Methodology (RSM) and ANOVA analysis. From the previous study, the outstanding parameter gained from the optimisation method in minimising the shrinkage at the moulded part was packing pressure. Therefore, with the reference from the previous literature, packing pressure was selected as the parameter setting for this study with other three parameters which are melt temperature, cooling time and mould temperature. The analysis of the process was obtained from the simulation by Autodesk Moldflow Insight (AMI) software and the material used for moulded part was Acrylonitrile Butadiene Styrene (ABS). The analysis and result were obtained and it found that the shrinkage can be minimised and the significant parameters were found as packing pressure, mould temperature and melt temperature.

Simulation and experimental study of resin flow in fibre fabrics

NASA Astrophysics Data System (ADS)

Yan, Fei; Yan, Shilin; Li, Yongjing

2017-06-01

Liquid Composite Moulding (LCM) is gradually becoming the most competitive manufacturing technology for producing large composite parts with complex geometry with high quality and low cost. These parts include those for airplanes, wind turbine blades and automobile components. Fibre fabrics in liquid composite moulding can be considered as dual-scale porous media. In different gap scales, an unsaturated flow is produced during the mould filling process. This particular flow behaviour deviates from the traditional Darcy’s law, which is used to calculate the filling pressure and will cause errors. According to sink theory, the unsaturated flow characteristics of this dual-scale porous media were studied in this paper, and a FEM solution program was developed. The results showed that the pressure curves against the position which simulated by sink functions were departure from the position of traditional theory. In addition, the simulation results of partially-saturated region were consistent with the experimental data.

Warpage optimisation on the moulded part with straight-drilled and conformal cooling channels using response surface methodology (RSM) and glowworm swarm optimisation (GSO)

NASA Astrophysics Data System (ADS)

Hazwan, M. H. M.; Shayfull, Z.; Sharif, S.; Nasir, S. M.; Zainal, N.

2017-09-01

In injection moulding process, quality and productivity are notably important and must be controlled for each product type produced. Quality is measured as the extent of warpage of moulded parts while productivity is measured as a duration of moulding cycle time. To control the quality, many researchers have introduced various of optimisation approaches which have been proven enhanced the quality of the moulded part produced. In order to improve the productivity of injection moulding process, some of researches have proposed the application of conformal cooling channels which have been proven reduced the duration of moulding cycle time. Therefore, this paper presents an application of alternative optimisation approach which is Response Surface Methodology (RSM) with Glowworm Swarm Optimisation (GSO) on the moulded part with straight-drilled and conformal cooling channels mould. This study examined the warpage condition of the moulded parts before and after optimisation work applied for both cooling channels. A front panel housing have been selected as a specimen and the performance of proposed optimisation approach have been analysed on the conventional straight-drilled cooling channels compared to the Milled Groove Square Shape (MGSS) conformal cooling channels by simulation analysis using Autodesk Moldflow Insight (AMI) 2013. Based on the results, melt temperature is the most significant factor contribute to the warpage condition and warpage have optimised by 39.1% after optimisation for straight-drilled cooling channels and cooling time is the most significant factor contribute to the warpage condition and warpage have optimised by 38.7% after optimisation for MGSS conformal cooling channels. In addition, the finding shows that the application of optimisation work on the conformal cooling channels offers the better quality and productivity of the moulded part produced.

Impact of Viscosity on Filling the Injection Mould Cavity

NASA Astrophysics Data System (ADS)

Satin, Lukáš; Bílik, Jozef

2016-09-01

The aim of this paper is to look closer at the rheological properties of plastics and their impact on technology in the plastics processing industry. The paper focuses on the influence of viscosity of the material on filling the mould cavity. Four materials were tested with the settings of process parameters with different viscosity. Using simulation software of Moldex3D, we can see the effect of change in viscosity in the material to be filled.

Warpage improvement on wheel caster by optimizing the process parameters using genetic algorithm (GA)

NASA Astrophysics Data System (ADS)

Safuan, N. S.; Fathullah, M.; Shayfull, Z.; Nasir, S. M.; Hazwan, M. H. M.

2017-09-01

In injection moulding process, the defects will always encountered and affected the final product shape and functionality. This study is concerning on minimizing warpage and optimizing the process parameter of injection moulding part. Apart from eliminating product wastes, this project also giving out best recommended parameters setting. This research studied on five parameters. The optimization showed that warpage have been improved 42.64% from 0.6524 mm to 0.30879 mm in Autodesk Moldflow Insight (AMI) simulation result and Genetic Algorithm (GA) respectively.

The effects of polymers' visco-elastoplastic properties on the micro cavities filling step of hot embossing process

NASA Astrophysics Data System (ADS)

Cheng, Gang; Barrière, Thierry

2018-05-01

The hot embossing process has been widely used in the manufacturing of polymer components, especially for the fabrication of micro or nano components. The significant advantage of the hot embossing process compared to the traditional injection moulding process is the excellent effective filling ratio for the high aspect ratio components and large surface structural components. The lack of material behavior modeling and numerical simulation limits the further development the hot embossing process, especially at the micro and nano scales. In this paper, a visco-elastoplastic behavior law has been proposed to describe the amorphous thermoplastic polymer mechanical properties in the hot embossing processing temperature range, which is lightly above their glass transition temperature. Uniaxial compression tests have been carried out in order to investigate the amorphous thermoplastic polymers properties. The material parameters in the visco-elastoplastic model have been identified according to the experimental results. A 3D numerical model has been created in the simulation software, which is based on the finite element method. The numerical simulation of the filling step of the hot embossing process has been effectuated by taking into account the viscous, elastic and plastic behaviors of thermoplastic polymers. The micro hot embossing process has been carried out using horizontal injection compression moulding equipment. A complete compression mould tool, equipped with the heating system, the cooling system, the ejection system and the vacuum system, has been designed and elaborated for this research work. The microfluidic devices based on the amorphous thermoplastic polymers have been successfully elaborated by hot embossing process. Proper agreement between the numerical simulation and the experimental elaboration has been obtained.

Warpage analysis in injection moulding process

NASA Astrophysics Data System (ADS)

Hidayah, M. H. N.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Hazwan, M. H. M.

2017-09-01

This study was concentrated on the effects of process parameters in plastic injection moulding process towards warpage problem by using Autodesk Moldflow Insight (AMI) software for the simulation. In this study, plastic dispenser of dental floss has been analysed with thermoplastic material of Polypropylene (PP) used as the moulded material and details properties of 80 Tonne Nessei NEX 1000 injection moulding machine also has been used in this study. The variable parameters of the process are packing pressure, packing time, melt temperature and cooling time. Minimization of warpage obtained from the optimization and analysis data from the Design Expert software. Integration of Response Surface Methodology (RSM), Center Composite Design (CCD) with polynomial models that has been obtained from Design of Experiment (DOE) is the method used in this study. The results show that packing pressure is the main factor that will contribute to the formation of warpage in x-axis and y-axis. While in z-axis, the main factor is melt temperature and packing time is the less significant among the four parameters in x, y and z-axes. From optimal processing parameter, the value of warpage in x, y and z-axis have been optimised by 21.60%, 26.45% and 24.53%, respectively.

A review of micro-powder injection moulding as a microfabrication technique

NASA Astrophysics Data System (ADS)

Attia, Usama M.; Alcock, Jeffrey R.

2011-04-01

Micro-powder injection moulding (µPIM) is a fast-developing micro-manufacturing technique for the production of metal and ceramic components. Shape complexity, dimensional accuracy, replication fidelity, material variety combined with high-volume capabilities are some of the key advantages of the technology. This review assesses the capabilities and limitations of µPIM as a micro-manufacturing technique by reviewing the latest developments in the area and by considering potential improvements. The basic elements of the process chain, variant processes and simulation attempts are discussed and evaluated. Challenges and research gaps are highlighted, and potential areas for improvement are presented.

Modelling of the rotational moulding process for the manufacture of plastic products

NASA Astrophysics Data System (ADS)

Khoon, Lim Kok

The present research is mainly focused on two-dimensional non-linear thermal modelling, numerical procedures and software development for the rotational moulding process. The RotoFEM program is developed for the rotational moulding process using finite element procedures. The program is written in the MATLAB environment. The research includes the development of new slip flow models, phase change study, warpage study and process analyses. A new slip flow methodology is derived for the heat transfer problem inside the enclosed rotating mould during the heating stage of the tumbling powder. The methodology enables the discontinuous powder to be modelled by the continuous-based finite element method. The Galerkin Finite Element Method is incorporated with the lumped-parameter system and the coincident node technique in finding the multi-interacting heat transfer solutions inside the mould. Two slip flow models arise from the slip flow methodology; they are SDM (single-layered deposition method) and MDM (multi-layered deposition method). These two models have differences in their thermal description for the internal air energy balance and the computational procedure for the deposition of the molten polymer. The SDM model assumes the macroscopic deposition of the molten polymer bed exists only between the bed and the inner mould surface. On the other hand, the MDM model allows the layer-by-layer deposition of the molten polymer bed macroscopically. In addition, the latter has a more detailed heat transfer description for the internal air inside the mould during the powder heating cycle. In slip flow models, the semi-implicit approach has been introduced to solve the final quasi-equilibrium internal air temperature during the heating cycle. A notable feature of this slip flow methodology is that the slip flow models are capable of producing good results for the internal air at the heating powder stage, without the consideration of the powder movement and changeable powder mass. This makes the modelling of the rotational moulding process much simpler. In the simulation of the cooling stage in rotational moulding, the thermal aspects of the inherent warpage problem and external-internal cooling method have been explored. The predicted internal air temperature profiles have shown that the less apparent crystallization plateau in the experimental internal air in practice could be related to warpage. Various phase change algorithms have been reviewed and compared, and thus the most convenient and considerable effective algorithm is proposed. The dimensional analysis method, expressed by means of dimensionless combinations of physical, boundary, and time variables, is utilized to study the dependence of the key thermal parameters on the processing times of rotational moulding. Lastly, the predicted results have been compared with the experimental results from two different external resources. The predicted temperature profiles of the internal air, oven times and other process conditions are consistent with the available data.

Injection moulding of optical functional micro structures using laser structured, PVD-coated mould inserts

NASA Astrophysics Data System (ADS)

Hopmann, Ch.; Weber, M.; Schöngart, M.; Schäfer, C.; Bobzin, K.; Bagcivan, N.; Brögelmann, T.; Theiß, S.; Münstermann, T.; Steger, M.

2015-05-01

Micro structured optical plastics components are intensively used i. e. in consumer electronics, for optical sensors in metrology, innovative LED-lighting or laser technology. Injection moulding has proven to be successful for the large-scale production of those parts. However, the production of those parts still causes difficulties due to challenges in the moulding and demoulding of plastics parts created with laser structured mould inserts. A complete moulding of the structures often leads to increased demoulding forces, which then cause a breaking of the structures and a clogging of the mould. An innovative approach is to combine PVD-coated (physical vapour deposition), laser structured inserts and a variothermal moulding process to create functional mic8iüro structures in a one-step process. Therefore, a PVD-coating is applied after the laser structuring process in order to improve the wear resistance and the anti-adhesive properties against the plastics melt. In a series of moulding trials with polycarbonate (PC) and polymethylmethacrylate (PMMA) using different coated moulds, the mould temperature during injection was varied in the range of the glass transition and the melt temperature of the polymers. Subsequently, the surface topography of the moulded parts is evaluated by digital 3D laser-scanning microscopy. The influence of the moulding parameters and the coating of the mould insert on the moulding accuracy and the demoulding behaviour are being analysed. It is shown that micro structures created by ultra-short pulse laser ablation can be successfully replicated in a variothermal moulding process. Due to the mould coating, significant improvements could be achieved in producing micro structured optical plastics components.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopmann, Ch.; Weber, M.; Schöngart, M.

Micro structured optical plastics components are intensively used i. e. in consumer electronics, for optical sensors in metrology, innovative LED-lighting or laser technology. Injection moulding has proven to be successful for the large-scale production of those parts. However, the production of those parts still causes difficulties due to challenges in the moulding and demoulding of plastics parts created with laser structured mould inserts. A complete moulding of the structures often leads to increased demoulding forces, which then cause a breaking of the structures and a clogging of the mould. An innovative approach is to combine PVD-coated (physical vapour deposition), lasermore » structured inserts and a variothermal moulding process to create functional mic8iüro structures in a one-step process. Therefore, a PVD-coating is applied after the laser structuring process in order to improve the wear resistance and the anti-adhesive properties against the plastics melt. In a series of moulding trials with polycarbonate (PC) and polymethylmethacrylate (PMMA) using different coated moulds, the mould temperature during injection was varied in the range of the glass transition and the melt temperature of the polymers. Subsequently, the surface topography of the moulded parts is evaluated by digital 3D laser-scanning microscopy. The influence of the moulding parameters and the coating of the mould insert on the moulding accuracy and the demoulding behaviour are being analysed. It is shown that micro structures created by ultra-short pulse laser ablation can be successfully replicated in a variothermal moulding process. Due to the mould coating, significant improvements could be achieved in producing micro structured optical plastics components.« less

Testing single point incremental forming moulds for rotomoulding operations

NASA Astrophysics Data System (ADS)

Afonso, Daniel; de Sousa, Ricardo Alves; Torcato, Ricardo

2017-10-01

Low pressure polymer processes as thermoforming or rotational moulding use much simpler moulds than high pressure processes like injection. However, despite the low forces involved in the process, moulds manufacturing for these applications is still a very material, energy and time consuming operation. Particularly in rotational moulding there is no standard for the mould manufacture and very different techniques are applicable. The goal of this research is to develop and validate a method for manufacturing plastically formed sheet metal moulds by single point incremental forming (SPIF) for rotomoulding and rotocasting operations. A Stewart platform based SPIF machine allow the forming of thick metal sheets, granting the required structural stiffness for the mould surface, and keeping a short manufacture lead time and low thermal inertia. The experimental work involves the proposal of a hollow part, design and fabrication of a sheet metal mould using dieless incremental forming techniques and testing its operation in the production of prototype parts.

Migration behaviour of silicone moulds in contact with different foodstuffs.

PubMed

Helling, Ruediger; Kutschbach, Katja; Joachim Simat, Thomas

2010-03-01

Various foodstuffs were prepared in silicone baking moulds and analyzed for siloxane migration using a previously developed and validated (1)H-NMR method. Meat loaf significantly exceeded the overall migration limit of 60 mg kg(-1) (10 mg sdm(-1)) in the first and third experiment. The highest siloxane migration found in a meat loaf after preparation in a commercial mould was 177 mg kg(-1). In contrast, milk-based food showed very low or non-detectable migration (<2.4 mg kg(-1)), even containing high fat levels. Similar results were achieved using 50% ethanol as the simulant for milk-based products, as defined in the Plastics Directive 2007/19/EEC. After solvent extraction of the moulds in simulating long-term usage, no further migration into the food was detectable, indicating that there is no significant formation of low molecular weight, potentially migrating siloxanes from the elastomer. During repeated usage, the moulds showed a high uptake of fat: up to 8.0 g fat per kg elastomer. Proper tempering of the moulds had a major influence on the migration properties of siloxanes into different foodstuffs. Non-tempered moulds with a high level of volatile organic compounds (1.1%) were shown to have considerably higher migration than the equivalent tempered moulds.

Optimisation of process parameters on thin shell part using response surface methodology (RSM) and genetic algorithm (GA)

NASA Astrophysics Data System (ADS)

Faiz, J. M.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Hazwan, M. H. M.

2017-09-01

This study conducts the simulation on optimisation of injection moulding process parameters using Autodesk Moldflow Insight (AMI) software. This study has applied some process parameters which are melt temperature, mould temperature, packing pressure, and cooling time in order to analyse the warpage value of the part. Besides, a part has been selected to be studied which made of Polypropylene (PP). The combination of the process parameters is analysed using Analysis of Variance (ANOVA) and the optimised value is obtained using Response Surface Methodology (RSM). The RSM as well as Genetic Algorithm are applied in Design Expert software in order to minimise the warpage value. The outcome of this study shows that the warpage value improved by using RSM and GA.

Integration Of Heat Transfer Coefficient In Glass Forming Modeling With Special Interface Element

NASA Astrophysics Data System (ADS)

Moreau, P.; César de Sá, J.; Grégoire, S.; Lochegnies, D.

2007-05-01

Numerical modeling of the glass forming processes requires the accurate knowledge of the heat exchange between the glass and the forming tools. A laboratory testing is developed to determine the evolution of the heat transfer coefficient in different glass/mould contact conditions (contact pressure, temperature, lubrication…). In this paper, trials are performed to determine heat transfer coefficient evolutions in experimental conditions close to the industrial blow-and-blow process conditions. In parallel of this work, a special interface element is implemented in a commercial Finite Element code in order to deal with heat transfer between glass and mould for non-meshing meshes and evolutive contact. This special interface element, implemented by using user subroutines, permits to introduce the previous heat transfer coefficient evolutions in the numerical modelings at the glass/mould interface in function of the local temperatures, contact pressures, contact time and kind of lubrication. The blow-and-blow forming simulation of a perfume bottle is finally performed to assess the special interface element performance.

Design and Production of the Injection Mould with a Cax Assistance

NASA Astrophysics Data System (ADS)

Likavčan, Lukáš; Frnčík, Martin; Zaujec, Rudolf; Satin, Lukáš; Martinkovič, Maroš

2016-09-01

This paper is focused on the process of designing the desired plastic component and injection mould by using the 3D CAD systems. The subsequent FEM analysis of the injection mould process was carried out in order to define shrinkage and deformation of the plastic material by CAE system. The dimensions of the mould were then modified to compensate the shrinkage effect. Machining process (milling and the laser texturing) of the mould was performed by using CAM systems. Finally, after the production of the plastic components by the injection mould technology, the inspection of the plastic component dimensions was carried out by CAQ in order to define the accuracy of the whole CAx chain. It was also demonstrated that CAx systems are an integral part of pre-production and production process.

Cycle time improvement for plastic injection moulding process by sub groove modification in conformal cooling channel

NASA Astrophysics Data System (ADS)

Kamarudin, K.; Wahab, M. S.; Batcha, M. F. M.; Shayfull, Z.; Raus, A. A.; Ahmed, Aqeel

2017-09-01

Mould designers have been struggling for the improvement of the cooling system performance, despite the fact that the cooling system complexity is physically limited by the fabrication capability of the conventional tooling methods. However, the growth of Solid Free Form Technology (SFF) allow the mould designer to develop more than just a regular conformal cooling channel. Numerous researchers demonstrate that conformal cooling channel was tremendously given significant result in the improvement of productivity and quality in the plastic injection moulding process. This paper presents the research work that applies the passive enhancement method in square shape cooling channel to enhance the efficiency of cooling performance by adding the sub groove to the cooling channel itself. Previous design that uses square shape cooling channel was improved by adding various numbers of sub groove to meet the best sub groove design that able reduced the cooling time. The effect of sub groove design on cooling time was investigated by Autodesk Modlflow Insight software. The simulation results showed that the various sub groove designs give different values to ejection time. The Design 7 showed the lowest value of ejection time with 24.3% increment. The addition of sub groove significantly increased a coolant velocity and a rate of heat transfer from molten plastic to coolant.

Multiphase and multiscale approaches for modelling the injection of textured moulds

NASA Astrophysics Data System (ADS)

Nakhoul, Rebecca; Laure, Patrice; Silva, Luisa; Vincent, Michel

2016-10-01

Micro-injection moulding is frequently used for the mass production of devices in micro-medical technologies, micro-optics and micro-mechanics. This work focuses mainly on offering numerical tools to model the injection of micro-textured moulds. Such tools can predict the different filling scenarios of the micro-details and consequently offer optimal operating conditions (mould and melt temperatures, melt flow, stresses, etc.) to analyse the final part quality. To do so, a full Eulerian approach is used to model the injection of textured moulds at both the macroscopic and microscopic scales as usual industrial software cannot handle the filling of micro details. Since heat transfers with the mould are very relevant due to high cooling rates, the coupling between micro- and macro- simulations is primordial to insure a complete and accurate representation of textured mould injection.

Integration Of Heat Transfer Coefficient In Glass Forming Modeling With Special Interface Element

DOE Office of Scientific and Technical Information (OSTI.GOV)

Moreau, P.; Gregoire, S.; Lochegnies, D.

2007-05-17

Numerical modeling of the glass forming processes requires the accurate knowledge of the heat exchange between the glass and the forming tools. A laboratory testing is developed to determine the evolution of the heat transfer coefficient in different glass/mould contact conditions (contact pressure, temperature, lubrication...). In this paper, trials are performed to determine heat transfer coefficient evolutions in experimental conditions close to the industrial blow-and-blow process conditions. In parallel of this work, a special interface element is implemented in a commercial Finite Element code in order to deal with heat transfer between glass and mould for non-meshing meshes and evolutivemore » contact. This special interface element, implemented by using user subroutines, permits to introduce the previous heat transfer coefficient evolutions in the numerical modelings at the glass/mould interface in function of the local temperatures, contact pressures, contact time and kind of lubrication. The blow-and-blow forming simulation of a perfume bottle is finally performed to assess the special interface element performance.« less

Study of injection moulded long glass fibre-reinforced polypropylene and the effect on the fibre length and orientation distribution

NASA Astrophysics Data System (ADS)

Parveeen, B.; Caton-Rose, P.; Costa, F.; Jin, X.; Hine, P.

2014-05-01

Long glass fibre (LGF) composites are extensively used in manufacturing to produce components with enhanced mechanical properties. Long fibres with length 12 to 25mm are added to a thermoplastic matrix. However severe fibre breakage can occur in the injection moulding process resulting in shorter fibre length distribution (FLD). The majority of this breakage occurs due to the melt experiencing extreme shear stress during the preparation and injection stage. Care should be taken to ensure that the longer fibres make it through the injection moulding process without their length being significantly degraded. This study is based on commercial 12 mm long glass-fibre reinforced polypropylene (PP) and short glass fibre Nylon. Due to the semi-flexiable behaviour of long glass fibres, the fibre orientation distribution (FOD) will differ from the orientation distribution of short glass fibre in an injection molded part. In order to investigate the effect the change in fibre length has on the fibre orientation distribution or vice versa, FOD data was measured using the 2D section image analyser. The overall purpose of the research is to show how the orientation distribution chnages in an injection moulded centre gated disc and end gated plaque geometry and to compare this data against fibre orientation predictions obtained from Autodesk Moldflow Simulation Insight.

High Power Picosecond Laser Surface Micro-texturing of H13 Tool Steel and Pattern Replication onto ABS Plastics via Injection Moulding

NASA Astrophysics Data System (ADS)

Otanocha, Omonigho B.; Li, Lin; Zhong, Shan; Liu, Zhu

2016-03-01

H13 tool steels are often used as dies and moulds for injection moulding of plastic components. Certain injection moulded components require micro-patterns on their surfaces in order to modify the physical properties of the components or for better mould release to reduce mould contamination. With these applications it is necessary to study micro-patterning to moulds and to ensure effective pattern transfer and replication onto the plastic component during moulding. In this paper, we report an investigation into high average powered (100 W) picosecond laser interactions with H13 tool steel during surface micro-patterning (texturing) and the subsequent pattern replication on ABS plastic material through injection moulding. Design of experiments and statistical modelling were used to understand the influences of laser pulse repetition rate, laser fluence, scanning velocity, and number of scans on the depth of cut, kerf width and heat affected zones (HAZ) size. The characteristics of the surface patterns are analysed. The process parameter interactions and significance of process parameters on the processing quality and efficiency are characterised. An optimum operating window is recommended. The transferred geometry is compared with the patterns generated on the dies. A discussion is made to explain the characteristics of laser texturing and pattern replication on plastics.

Integrated analyses in plastics forming

NASA Astrophysics Data System (ADS)

Bo, Wang

This is the thesis which explains the progress made in the analysis, simulation and testing of plastics forming. This progress can be applied to injection and compression mould design. Three activities of plastics forming have been investigated, namely filling analysis, cooling analysis and ejecting analysis. The filling section of plastics forming has been analysed and calculated by using MOLDFLOW and FILLCALC V. software. A comparing of high speed compression moulding and injection moulding has been made. The cooling section of plastics forming has been analysed by using MOLDFLOW software and a finite difference computer program. The latter program can be used as a sample program to calculate the feasibility of cooling different materials to required target temperatures under controlled cooling conditions. The application of thermal imaging has been also introduced to determine the actual process temperatures. Thermal imaging can be used as a powerful tool to analyse mould surface temperatures and to verify the mathematical model. A buckling problem for ejecting section has been modelled and calculated by PATRAN/ABAQUS finite element analysis software and tested. These calculations and analysis are applied to the special case but can be use as an example for general analysis and calculation in the ejection section of plastics forming.

A novel scalable manufacturing process for the production of hydrogel-forming microneedle arrays.

PubMed

Lutton, Rebecca E M; Larrañeta, Eneko; Kearney, Mary-Carmel; Boyd, Peter; Woolfson, A David; Donnelly, Ryan F

2015-10-15

A novel manufacturing process for fabricating microneedle arrays (MN) has been designed and evaluated. The prototype is able to successfully produce 14×14 MN arrays and is easily capable of scale-up, enabling the transition from laboratory to industry and subsequent commercialisation. The method requires the custom design of metal MN master templates to produce silicone MN moulds using an injection moulding process. The MN arrays produced using this novel method was compared with centrifugation, the traditional method of producing aqueous hydrogel-forming MN arrays. The results proved that there was negligible difference between either methods, with each producing MN arrays with comparable quality. Both types of MN arrays can be successfully inserted in a skin simulant. In both cases the insertion depth was approximately 60% of the needle length and the height reduction after insertion was in both cases approximately 3%. Copyright © 2015 Elsevier B.V. All rights reserved.

A novel scalable manufacturing process for the production of hydrogel-forming microneedle arrays

PubMed Central

Lutton, Rebecca E.M.; Larrañeta, Eneko; Kearney, Mary-Carmel; Boyd, Peter; Woolfson, A.David; Donnelly, Ryan F.

2015-01-01

A novel manufacturing process for fabricating microneedle arrays (MN) has been designed and evaluated. The prototype is able to successfully produce 14 × 14 MN arrays and is easily capable of scale-up, enabling the transition from laboratory to industry and subsequent commercialisation. The method requires the custom design of metal MN master templates to produce silicone MN moulds using an injection moulding process. The MN arrays produced using this novel method was compared with centrifugation, the traditional method of producing aqueous hydrogel-forming MN arrays. The results proved that there was negligible difference between either methods, with each producing MN arrays with comparable quality. Both types of MN arrays can be successfully inserted in a skin simulant. In both cases the insertion depth was approximately 60% of the needle length and the height reduction after insertion was in both cases approximately 3%. PMID:26302858

DOE Office of Scientific and Technical Information (OSTI.GOV)

Potiron, A.; Gerometta, C.; Plun, J.M.

Simulation of casting processes is now industrially available with different softwares proposed to foundrymen. Yet, it is always difficult to provide the boundary conditions as correct as possible to represent accurately the environment of the mould. The knowledge of heat transfer coefficient used to modelize the cooling devices in permanent moulds is very important, as well as the acquisition of accurate data regarding die coatings or physical properties. After having conducted a sample survey with French foundries, the experiment conditions have been defined. Two main types of cooling device have been studied: water running in a pipe and air flowingmore » in a special shape to provide localized cooling. Some of the heat transfer coefficients have been simply calculated using Colburn`s law, others have been determined using a 1D or 2D inverse method. Auto-validation results obtained on the experimental device simulated with SIMULOR, a 3D finite volume software, are encouraging.« less

Influence of the recycled material percentage on the rheological behaviour of HDPE for injection moulding process.

PubMed

Javierre, C; Clavería, I; Ponz, L; Aísa, J; Fernández, A

2007-01-01

The amount of polymer material wasted during thermoplastic injection moulding is very high. It comes from both the feed system of the part, and parts necessary to set up the mould, as well as the scrap generated along the process due to quality problems. The residues are managed through polymer recycling that allows reuse of the materials in the manufacturing injection process. Recycling mills convert the parts into small pieces that are used as feed material for injection, by mixing the recycled feedstock in different percentages with raw material. This mixture of both raw and recycled material modifies material properties according to the percentage of recycled material introduced. Some of the properties affected by this modification are those related to rheologic behaviour, which strongly conditions the future injection moulding process. This paper analyzes the rheologic behaviour of material with different percentages of recycled material by means of a capillary rheometer, and evaluates the influence of the corresponding viscosity curves obtained on the injection moulding process, where small variations of parameters related to rheological behaviour, such as pressure or clamping force, can be critical to the viability and cost of the parts manufactured by injection moulding.

On creativity of slime mould

NASA Astrophysics Data System (ADS)

Adamatzky, Andrew; Armstrong, Rachel; Jones, Jeff; Gunji, Yukio-Pegio

2013-07-01

Slime mould Physarum polycephalum is large single cell with intriguingly smart behaviour. The slime mould shows outstanding abilities to adapt its protoplasmic network to varying environmental conditions. The slime mould can solve tasks of computational geometry, image processing, logics and arithmetics when data are represented by configurations of attractants and repellents. We attempt to map behavioural patterns of slime onto the cognitive control vs. schizotypy spectrum phase space and thus interpret slime mould's activity in terms of creativity.

Slime mould biotechnology

NASA Astrophysics Data System (ADS)

Mayne, Richard

2015-03-01

Slime mould computing is an inherently multi-disciplinary subfield of unconventional computing that draws upon aspects of not only theoretical computer science and electronics, but also the natural sciences. This chapter focuses on the biology of slime moulds and expounds the viewpoint that a deep, intuitive understanding of slime mould life processes is a fundamental requirement for understanding -- and, hence, harnessing -- the incredible behaviour patterns we may characterise as "computation"...

Optimisation of warpage on thin shell part by using particle swarm optimisation (PSO)

NASA Astrophysics Data System (ADS)

Norshahira, R.; Shayfull, Z.; Nasir, S. M.; Saad, S. M. Sazli; Fathullah, M.

2017-09-01

As the product nowadays moving towards thinner design, causing the production of the plastic product facing a lot of difficulties. This is due to the higher possibilities of defects occur as the thickness of the wall gets thinner. Demand for technique in reducing the defects increasing due to this factor. These defects has seen to be occur due to several factors in injection moulding process. In the study a Moldflow software was used in simulating the injection moulding process. While RSM is used in producing the mathematical model to be used as the input fitness function for the Matlab software. Particle Swarm Optimisation (PSO) technique is used in optimising the processing condition to reduce the amount of shrinkage and warpage of the plastic part. The results shows that there are a warpage reduction of 17.60% in x direction, 18.15% in y direction and 10.25% reduction in z direction respectively. The results shows the reliability of this artificial method in minimising the product warpage.

Development of Rapid Pipe Moulding Process for Carbon Fiber Reinforced Thermoplastics by Direct Resistance Heating

NASA Astrophysics Data System (ADS)

Tanaka, Kazuto; Harada, Ryuki; Uemura, Toshiki; Katayama, Tsutao; Kuwahara, Hideyuki

To deal with environmental issues, the gasoline mileage of passenger cars can be improved by reduction of the car weight. The use of car components made of Carbon Fiber Reinforced Plastics (CFRP) is increasing because of its superior mechanical properties and relatively low density. Many vehicle structural parts are pipe-shaped, such as suspension arms, torsion beams, door guard bars and impact beams. A reduction of the car weight is expected by using CFRP for these parts. Especially, when considering the recyclability and ease of production, Carbon Fiber Reinforced Thermoplastics are a prime candidate. On the other hand, the moulding process of CFRTP pipes for mass production has not been well established yet. For this pipe moulding process an induction heating method has been investigated already, however, this method requires a complicated coil system. To reduce the production cost, another system without such complicated equipment is to be developed. In this study, the pipe moulding process of CFRTP using direct resistance heating was developed. This heating method heats up the mould by Joule heating using skin effect of high-frequency current. The direct resistance heating method is desirable from a cost perspective, because this method can heat the mould directly without using any coils. Formerly developed Non-woven Stitched Multi-axial Cloth (NSMC) was used as semi-product material. NSMC is very suitable for the lamination process due to the fact that non-crimp stitched carbon fiber of [0°/+45°/90°/-45°] and polyamide 6 non-woven fabric are stitched to one sheet, resulting in a short production cycle time. The use of the pipe moulding process with the direct resistance heating method in combination with the NSMC, has resulted in the successful moulding of a CFRTP pipe of 300 mm in length, 40 mm in diameter and 2 mm in thickness.

Effects of mould on electrochemical migration behaviour of immersion silver finished printed circuit board.

PubMed

Yi, Pan; Xiao, Kui; Dong, Chaofang; Zou, Shiwen; Li, Xiaogang

2018-02-01

The role played by mould in the electrochemical migration (ECM) behaviour of an immersion silver finished printed circuit board (PCB-ImAg) under a direct current (DC) bias was investigated. An interesting phenomenon is found whereby mould, especially Aspergillus niger, can preferentially grow well on PCB-ImAg under electrical bias and then bridge integrated circuits and form a migration path. The cooperation of the mould and DC bias aggravates the ECM process occurring on PCB-ImAg. When the bias voltage is below 15V, ECM almost does not occur for Ag coating. Mechanisms that explain the ECM processes of PCB-ImAg in the presence of mould and DC bias are proposed. Copyright © 2017. Published by Elsevier B.V.

Optimization of Gate, Runner and Sprue in Two-Plate Family Plastic Injection Mould

NASA Astrophysics Data System (ADS)

Amran, M. A.; Hadzley, M.; Amri, S.; Izamshah, R.; Hassan, A.; Samsi, S.; Shahir, K.

2010-03-01

This paper describes the optimization size of gate, runner and sprue in two-plate family plastic injection mould. An Electronic Cash Register (ECR) plastic product was used in this study, which there are three components in electronic cast register plastic product consist of top casing, bottom casing and paper holder. The objectives of this paper are to find out the optimum size of gate, runner and sprue, to locate the optimum layout of cavities and to recognize the defect problems due to the wrong size of gate, runner and sprue. Three types of software were used in this study, which Unigraphics software as CAD tool was used to design 3D modeling, Rhinoceros software as post processing tool was used to design gate, runner and sprue and Moldex software as simulation tool was used to analyze the plastic flow. As result, some modifications were made on size of feeding system and location of cavity to eliminate the short- shot, over filling and welding line problems in two-plate family plastic injection mould.

A concept for non-invasive temperature measurement during injection moulding processes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hopmann, Christian; Spekowius, Marcel, E-mail: spekowius@ikv.rwth-aachen.de; Wipperfürth, Jens

2016-03-09

Current models of the injection moulding process insufficiently consider the thermal interactions between melt, solidified material and the mould. A detailed description requires a deep understanding of the underlying processes and a precise observation of the temperature. Because todays measurement concepts do not allow a non-invasive analysis it is necessary to find new measurement techniques for temperature measurements during the manufacturing process. In this work we present the idea of a set up for a tomographic ultrasound measurement of the temperature field inside a plastics melt. The goal is to identify a concept that can be installed on a specializedmore » mould for the injection moulding process. The challenges are discussed and the design of a prototype is shown. Special attention is given to the spatial arrangement of the sensors. Besides the design of a measurement set up a reconstruction strategy for the ultrasound signals is required. We present an approach in which an image processing algorithm can be used to calculate a temperature distribution from the ultrasound scans. We discuss a reconstruction strategy in which the ultrasound signals are converted into a spartial temperature distribution by using pvT curves that are obtained by dilatometer measurements.« less

Individualized 3D scanning and printing for non-melanoma skin cancer brachytherapy: a financial study for its integration into clinical workflow.

PubMed

Arenas, Meritxell; Sabater, Sebastià; Sintas, Andreu; Arguís, Monica; Hernández, Víctor; Árquez, Miguel; López, Iolanda; Rovirosa, Àngeles; Puig, Doménec

2017-06-01

Skin cancer is the most common tumor in the population. There are different therapeutic modalities. Brachytherapy is one of the techniques used, in which it is necessary to build customized moulds for some patients. Currently, these moulds are made by hand using rudimentary techniques. We present a new procedure based on 3D printing and the analysis of the clinical workflow. Moulds can be made either by hand or by automated 3D printing. For making moulds by hand, a patient's alginate negative is created and, from that, the gypsum cast and customized moulds are made by hand from the patient's negative template. The new process is based on 3D printing. The first step is to take a 3D scan of the surface of the patient and then, 3D modelling software is used to obtain an accurate anatomical reconstruction of the treatment area. We present the clinical workflow using 3D scanning and printing technology, comparing its costs with the usual custom handmade mould protocol. The time spent for the new process is 6.25 hours, in contrast to the time spent for the conventional process, which is 9.5 hours. We found a 34% reduction in time required to create a mould for brachytherapy treatment. The labor cost of the conventional process is 211.5 vs. 152.5 hours, so the reduction is 59 hours. There is also a 49.5% reduction in the financial costs, mostly due to lack of need of a computed tomography (CT) scan of the gypsum and the mould. 3D scanning and printing offers financial benefits and reduces the clinical workload. As the present project demonstrates, through the application of 3D printing technologies, the costs and time spent during the process in the clinical workload in brachytherapy treatment are reduced. Overall, 3D printing is a promising technique for brachytherapy that might be well received in the community.

Mathematical model of the metal mould surface temperature optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mlynek, Jaroslav, E-mail: jaroslav.mlynek@tul.cz; Knobloch, Roman, E-mail: roman.knobloch@tul.cz; Srb, Radek, E-mail: radek.srb@tul.cz

2015-11-30

The article is focused on the problem of generating a uniform temperature field on the inner surface of shell metal moulds. Such moulds are used e.g. in the automotive industry for artificial leather production. To produce artificial leather with uniform surface structure and colour shade the temperature on the inner surface of the mould has to be as homogeneous as possible. The heating of the mould is realized by infrared heaters located above the outer mould surface. The conceived mathematical model allows us to optimize the locations of infrared heaters over the mould, so that approximately uniform heat radiation intensitymore » is generated. A version of differential evolution algorithm programmed in Matlab development environment was created by the authors for the optimization process. For temperate calculations software system ANSYS was used. A practical example of optimization of heaters locations and calculation of the temperature of the mould is included at the end of the article.« less

[Study on the application of value of digital medical technology in the operation on primary liver cancer].

PubMed

Fang, Chi-hua; Lu, Chao-min; Huang, Yan-peng; Li, Xiao-feng; Fan, Ying-fang; Yang, Jian; Xiang, Nan; Pan, Jia-hui

2009-04-01

To study the clinical application of digital medical in the operation on primary liver cancer. The patients (n=11) with primary hepatic carcinoma treated between February and July 2008, including 9 cases of hepatocellular carcinoma, 2 cases of cholangiocellular carcinoma, were scanned using 64 slices helicon computerized tomography (CT) and the datasets was collected. Segment and three-dimensional (3D) reconstruction of the CT image was carried out by the medical image processing system which was developed. And the 3D moulds were imported to the FreeForm Modeling System for smoothing. Then the hepatectomy in treatment of hepatoma and implanting of catheter were simulated with the force-feedback equipment (PHANToM). Finally, 3D models and results of simulation surgery were used for choosing mode of operation and comparing with the findings during the operation. The reconstructed models were true to life, and their spatial disposition and correlation were shown clearly; Blood supply of primary liver cancer could be seen easily. In the simulation surgery system, the process of virtual partial hepatectomy and implanting of catheter using simulation scalpel and catheter on 3D moulds with PHANToM was consistent with the clinical course of surgery. Life-like could be felt and power feeling can be touched during simulation operation. Digital medical benefited knowing the relationship between primary liver cancer and the intrahepatic pipe. It gave an advantage to complete primary liver cancer resection with more liver volume remained. It can improve the surgical effect and decrease the surgical risk and reduce the complication through demonstrating visualized operation before surgery.

Warpage investigation on side arms using response surface methodology (RSM) and glow-worm swarm optimizations (GSO)

NASA Astrophysics Data System (ADS)

Sow, C. K.; Fathullah, M.; Nasir, S. M.; Shayfull, Z.; Shazzuan, S.

2017-09-01

This paper discusses on an analysis run via injection moulding process in determination of the optimum processing parameters used for manufacturing side arms of catheters in minimizing the warpage issues. The optimization method used was RSM. Moreover, in this research tries to find the most significant factor affecting the warpage. From the previous literature review,4 most significant parameters on warpage defect was selected. Those parameters were melt temperature, packing time, packing pressure, mould temperature and cooling time. At the beginning, side arm was drawn using software of CATIA V5. Then, software Mouldflow and Design Expert were employed to analyses on the popular warpage issues. After that, GSO artificial intelligence was apply using the mathematical model from Design Expert for more optimization on RSM result. Recommended parameter settings from the simulation work were then compared with the optimization work of RSM and GSO. The result show that the warpage on the side arm was improved by 3.27 %

The effect of internal mould water spray cooling on rotationally moulded polyethylene parts

NASA Astrophysics Data System (ADS)

McCourt, Mark P.; Kearns, Mark P.; Martin, Peter J.

2018-05-01

The conventional method of cooling during the rotational moulding process is through the use of forced air. During the cooling phase of a typical rotomoulding cycle, large volumes of high velocity room temperature air are forced across the outside of the rotating rotomoulding tool to encourage cooling of the metal mould and molten polymer. Since no cooling is applied to the inside of the mould, the inner surface of the polymer (polyethylene) cools more slowly and will have a tendency to be more crystalline and the polyethylene will have a higher density in this region. The side that cools more quickly (in contact with the inside mould wall) will be less crystalline, and will therefore have a lower density. The major consequence of this difference in crystallinity will be a buildup of internal stresses producing warpage and excessive shrinkage of the part with subsequent increased levels of scrap. Therefore excessive cooling on the outside of the mould should be avoided. One consequence of this effect is that the cooling time for a standard rotationally moulded part can be quite long and this has an effect on the overall economics of the process in terms of part manufacture. A number of devices are currently on the market to enhance the cooling of rotational moulding by introducing a water spray to the inside of the rotomoulding during cooling. This paper reports on one such device 'Rotocooler' which during a series of initial industrial trials has been shown to reduce the cycletime by approximately 12 to 16%, with minimal effect on the mechanical properties, leading to a part which has less warpage and shrinkage than a conventionally cooled part.

Resin Flow Behavior Simulation of Grooved Foam Sandwich Composites with the Vacuum Assisted Resin Infusion (VARI) Molding Process

PubMed Central

Zhao, Chenhui; Zhang, Guangcheng; Wu, Yibo

2012-01-01

The resin flow behavior in the vacuum assisted resin infusion molding process (VARI) of foam sandwich composites was studied by both visualization flow experiments and computer simulation. Both experimental and simulation results show that: the distribution medium (DM) leads to a shorter molding filling time in grooved foam sandwich composites via the VARI process, and the mold filling time is linearly reduced with the increase of the ratio of DM/Preform. Patterns of the resin sources have a significant influence on the resin filling time. The filling time of center source is shorter than that of edge pattern. Point pattern results in longer filling time than of linear source. Short edge/center patterns need a longer time to fill the mould compared with Long edge/center sources.

Numerical modelling of heat transfer in a cavity due to liquid jet impingement for liquid supported stretch blow moulding

NASA Astrophysics Data System (ADS)

Smyth, Trevor; Menary, Gary; Geron, Marco

2018-05-01

Impingement of a liquid jet in a polymer cavity has been modelled numerically in this study. Liquid supported stretch blow moulding is a nascent polymer forming process using liquid as the forming medium to produce plastic bottles. The process derives from the conventional stretch blow moulding process which uses compressed air to deform the preform. Heat transfer away from the preform greatly increases when a liquid instead of a gas is flowing over a solid; in the blow moulding process the temperature of the preform is tightly controlled to achieve optimum forming conditions. A model was developed with Computational Fluid Dynamics code ANSYS Fluent which allows the extent of heat transfer between the incoming liquid and the solid preform to be determined in the initial transient stage, where a liquid jet enters an air filled preform. With this data, an approximation of the extent of cooling through the preform wall can be determined.

3D-printed surface mould applicator for high-dose-rate brachytherapy

NASA Astrophysics Data System (ADS)

Schumacher, Mark; Lasso, Andras; Cumming, Ian; Rankin, Adam; Falkson, Conrad B.; Schreiner, L. John; Joshi, Chandra; Fichtinger, Gabor

2015-03-01

In contemporary high-dose-rate brachytherapy treatment of superficial tumors, catheters are placed in a wax mould. The creation of current wax models is a difficult and time consuming proces.The irradiation plan can only be computed post-construction and requires a second CT scan. In case no satisfactory dose plan can be created, the mould is discarded and the process is repeated. The objective of this work was to develop an automated method to replace suboptimal wax moulding. We developed a method to design and manufacture moulds that guarantee to yield satisfactory dosimetry. A 3D-printed mould with channels for the catheters designed from the patient's CT and mounted on a patient-specific thermoplastic mesh mask. The mould planner was implemented as an open-source module in the 3D Slicer platform. Series of test moulds were created to accommodate standard brachytherapy catheters of 1.70mm diameter. A calibration object was used to conclude that tunnels with a diameter of 2.25mm, minimum 12mm radius of curvature, and 1.0mm open channel gave the best fit for this printer/catheter combination. Moulds were created from the CT scan of thermoplastic mesh masks of actual patients. The patient-specific moulds have been visually verified to fit on the thermoplastic meshes. The masks were visually shown to fit onto the thermoplastic meshes, next the resulting dosimetry will have to be compared with treatment plans and dosimetry achieved with conventional wax moulds in order to validate our 3D printed moulds.

Filling of high aspect ratio micro features of a microfluidic flow cytometer chip using micro injection moulding

NASA Astrophysics Data System (ADS)

Zhang, Haoyang; Fang, Fengzhou; Gilchrist, Michael D.; Zhang, Nan

2018-07-01

Micro injection moulding has been demonstrated as one of the most efficient mass production technologies for manufacturing polymeric microfluidic devices, which have been widely used in life sciences, environmental and analytical fields and agro-food industries. However, the filling of micro features for typical microfluidic devices is complicated and not yet fully understood, which consequently restricts the chip development. In the present work, a microfluidic flow cytometer chip with essential high aspect ratio micro features was used as a typical model to study their filling process. Short-shot experiments and single factor experiments were performed to examine the filling progress of such features during the injection and packing stages of the micro injection moulding process. The influence of process parameters such as shot size, packing pressure, packing time and mould temperature were systematically monitored, characterised and correlated with 3D measurements and real response of the machine such as screw velocity and screw position. A combined melt flow and creep deformation model was proposed to explain the complex influence of process on replication. An approach of over-shot micro injection moulding was proposed and was shown to be effective at improving the replication quality of high aspect ratio micro features.

Design and fabrication hazard stakes golf course polymeric foam material empty bunch (EFB) fiber reinforced

NASA Astrophysics Data System (ADS)

Zulfahmi; Syam, B.; Wirjosentono, B.

2018-02-01

A golf course with obstacles in the forms of water obstacle and lateral water obstacle marked with the stakes which are called golf course obstacle stake in this study. This study focused on the design and fabrication of the golf course obstacle stake with a solid cylindrical geometry using EFB fiber-reinforced polimeric foam composite materials. To obtain the EFB fiber which is free from fat content and other elements, EFB is soaked in the water with 1% (of the watre total volume) NaOH. The model of the mould designed is permanent mould that can be used for the further refabrication process. The mould was designed based on resin-compound paste materials with talc powder plus E-glass fiber to make the mould strong. The composition of polimeric foam materials comprised unsaturated resin Bqtn-Ex 157 (70%), blowing agent (10%), fiber (10%), and catalyst (10%). The process of casting the polimeric foam composit materials into the mould cavity should be at vertical casting position, accurate interval time of material stirring, and periodical casting. To find out the strength value of the golf course obstacle stake product, a model was made and simulated by using the software of Ansys workbench 14.0, an impact loading was given at the height of 400 mm and 460 mm with the variation of golf ball speed (USGA standard) v = 18 m/s, v = 35 m/s, v = 66.2 m/s, v = 70 m/s, and v = 78.2 m/s. The clarification showed that the biggest dynamic explicit loading impact of Fmax = 142.5 N at the height of 460 mm with the maximum golf ball speed of 78.2 m/s did not experience the hysteresis effect and inertia effect. The largest deformation area occurred at the golf ball speed v = 66.2 mm/s, that is 18.029 mm (time: 2.5514e-004) was only concentrated around the sectional area of contact point of impact, meaning that the golf course obstacle stakes made of EFB fiber-reinforced polymeric foam materials have the geometric functional strength that are able to absorb the energy of golf ball impact.

Optimisation of warpage on plastic injection moulding part using response surface methodology (RSM)

NASA Astrophysics Data System (ADS)

Miza, A. T. N. A.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Rashidi, M. M.

2017-09-01

The warpage is often encountered which occur during injection moulding process of thin shell part depending the process condition. The statistical design of experiment method which are Integrating Finite Element (FE) Analysis, moldflow analysis and response surface methodology (RSM) are the stage of few ways in minimize the warpage values of x,y and z on thin shell plastic parts that were investigated. A battery cover of a remote controller is one of the thin shell plastic part that produced by using injection moulding process. The optimum process condition parameter were determined as to achieve the minimum warpage from being occur. Packing pressure, Cooling time, Melt temperature and Mould temperature are 4 parameters that considered in this study. A two full factorial experimental design was conducted in Design Expert of RSM analysis as to combine all these parameters study. FE analysis result gain from analysis of variance (ANOVA) method was the one of the important process parameters influenced warpage. By using RSM, a predictive response surface model for warpage data will be shown.

Efficient machining of ultra precise steel moulds with freeform surfaces

NASA Astrophysics Data System (ADS)

Bulla, B.; Robertson, D. J.; Dambon, O.; Klocke, F.

2013-09-01

Ultra precision diamond turning of hardened steel to produce optical quality surfaces can be realized by applying an ultrasonic assisted process. With this technology optical moulds used typically for injection moulding can be machined directly from steel without the requirement to overcoat the mould with a diamond machinable material such as Nickel Phosphor. This has both the advantage of increasing the mould tool lifetime and also reducing manufacture costs by dispensing with the relatively expensive plating process. This publication will present results we have obtained for generating free form moulds in hardened steel by means of ultrasonic assisted diamond turning with a vibration frequency of 80 kHz. To provide a baseline with which to characterize the system performance we perform plane cutting experiments on different steel alloys with different compositions. The baseline machining results provides us information on the surface roughness and on tool wear caused during machining and we relate these to material composition. Moving on to freeform surfaces, we will present a theoretical background to define the machine program parameters for generating free forms by applying slow slide servo machining techniques. A solution for optimal part generation is introduced which forms the basis for the freeform machining experiments. The entire process chain, from the raw material through to ultra precision machining is presented, with emphasis on maintaining surface alignment when moving a component from CNC pre-machining to final machining using ultrasonic assisted diamond turning. The free form moulds are qualified on the basis of the surface roughness measurements and a form error map comparing the machined surface with the originally defined surface. These experiments demonstrate the feasibility of efficient free form machining applying ultrasonic assisted diamond turning of hardened steel.

Hot Melt Extruded and Injection Moulded Dosage Forms: Recent Research and Patents.

PubMed

Major, Ian; McConville, Christopher

2015-01-01

Hot Melt Extrusion (HME) and Injection Moulding (IM) are becoming more prevalent in the drug delivery field due to their continuous nature and advantages over current pharmaceutical manufacturing techniques. Hot melt extrusion (HME) is a process that involves the use of at least one reciprocating screw to force a thermoplastic resin along a heated barrel and through a die, while injection moulding is a forming process were molten polymer is forced at high pressure to enter a mould. HME offers a number of advantages over conventional pharmaceutical manufacturing techniques such as increased solubility and bioavailability of poorly water soluble drugs, a solvent free and continuous process, improved content uniformity and flexibility in manufacture. Injection moulding (IM) has been recognised as a rapid and versatile manufacturing technique, which has the advantages of being a continuous process, which is easily scaled up by the use of larger equipment and moulds. However, despite their advantages and the significant number of publications and patents on HME and IM drug delivery devices there are very few marketed formulations. These marketed products range from oral dosage forms which improve bioavailability and reduce pill burden to vaginal rings which provide long-term controlled release thus improving patient compliance. The patenting strategy for IM and HME seems to be focused towards patenting the finished product, more so than patenting the manufacturing process. This is probably due to the fact that the IM and HME processes have already been patented. HME is a process where raw materials (i.e. polymer, plasticizer, drug etc.) are mixed and pumped along by a rotating screw(s) at elevated temperatures through a die to produce a product of uniform shape. IM is similar to HME except that the raw materials are pushed into a mould which is set at lower temperatures. Interest in the use of HME and IM within the pharmaceutical industry is growing with as steady increase in the number of HME patents being issued and with more than 10 products, ranging from oral dosage forms to implantable devices, currently on the market. Therefore, this review of HME and IM is important to the scientific community to further understand and advance these novel and exciting manufacturing techniques.

The Optimisation of Processing Condition for Injected Mould Polypropylene-Nanoclay-Gigantochloa Scortechinii based on Melt Flow Index

NASA Astrophysics Data System (ADS)

Othman, M. H.; Rosli, M. S.; Hasan, S.; Amin, A. M.; Hashim, M. Y.; Marwah, O. M. F.; Amin, S. Y. M.

2018-03-01

The fundamental knowledge of flow behaviour is essential in producing various plastic parts injection moulding process. Moreover, the adaptation of advanced polymer-nanocomposites such as polypropylene-nanoclay with natural fibres, for instance Gigantochloa Scortechinii may boost up the mechanical properties of the parts. Therefore, this project was proposed with the objective to optimise the processing condition of injected mould polypropylene-nanoclay-Gigantochloa Scortechini fibres based on the flow behaviour, which was melt flow index. At first, Gigantochloa Scortechinii fibres have to be preheated at temperature 120°C and then mixed with polypropylene, maleic anhydride modified polypropylene oligomers (PPgMA) and nanoclay by using Brabender Plastograph machine. Next, forms of pellets were produced from the samples by using Granulator machine for use in the injection moulding process. The design of experiments that was used in the injection moulding process was Taguchi Method Orthogonal Array -L934. Melt Flow Index (MF) was selected as the response. Based on the results, the value of MFI increased when the fiber content increase from 0% to 3%, which was 17.78 g/10min to 22.07 g/10min and decreased from 3% to 6%, which was 22.07 g/10min to 20.05 g/10min and 3%, which gives the highest value of MFI. Based on the signal to ratio analysis, the most influential parameter that affects the value of MFI was the melt temperature. The optimum parameter for 3% were 170°C melt temperature, 35% packing pressure, 30% screw speed and 3 second filling time.

Optimisation of multi-layer rotationally moulded foamed structures

NASA Astrophysics Data System (ADS)

Pritchard, A. J.; McCourt, M. P.; Kearns, M. P.; Martin, P. J.; Cunningham, E.

2018-05-01

Multi-layer skin-foam and skin-foam-skin sandwich constructions are of increasing interest in the rotational moulding process for two reasons. Firstly, multi-layer constructions can improve the thermal insulation properties of a part. Secondly, foamed polyethylene sandwiched between solid polyethylene skins can increase the mechanical properties of rotationally moulded structural components, in particular increasing flexural properties and impact strength (IS). The processing of multiple layers of polyethylene and polyethylene foam presents unique challenges such as the control of chemical blowing agent decomposition temperature, and the optimisation of cooling rates to prevent destruction of the foam core; therefore, precise temperature control is paramount to success. Long cooling cycle times are associated with the creation of multi-layer foam parts due to their insulative nature; consequently, often making the costs of production prohibitive. Devices such as Rotocooler®, a rapid internal mould water spray cooling system, have been shown to have the potential to significantly decrease cooling times in rotational moulding. It is essential to monitor and control such devices to minimise the warpage associated with the rapid cooling of a moulding from only one side. The work presented here demonstrates the use of threaded thermocouples to monitor the polymer melt in multi-layer sandwich constructions, in order to analyse the cooling cycle of multi-layer foamed structures. A series of polyethylene skin-foam test mouldings were produced, and the effect of cooling medium on foam characteristics, mechanical properties, and process cycle time were investigated. Cooling cycle time reductions of 45%, 26%, and 29% were found for increasing (1%, 2%, and 3%) chemical blowing agent (CBA) amount when using internal water cooling technology from ˜123°C compared with forced air cooling (FAC). Subsequently, a reduction of IS for the same skin-foam parts was found to be 1%, 4%, and 16% compared with FAC.

Bolted Joints in Three Axially Braided Carbon Fibre/Epoxy Textile Composites with Moulded-in and Drilled Fastener Holes

NASA Astrophysics Data System (ADS)

Ataş, Akın; Gautam, Mayank; Soutis, Constantinos; Potluri, Prasad

2017-04-01

Experimental behaviour of bolted joints in triaxial braided (0°/±45°) carbon fibre/epoxy composite laminates with drilled and moulded-in fastener holes has been investigated in this paper. Braided laminates were manufactured by vacuum infusion process using 12 K T700S carbon fibres (for bias and axial tows) and Araldite LY-564 epoxy resin. Moulded-in fastener holes were formed using guide pins which were inserted in the braided structure prior to the vacuum infusion process. The damage mechanism of the specimens was investigated using ultrasonic C-Scan technique. The specimens were dimensioned to obtain a bearing mode of failure. The bearing strength of the specimens with moulded-in hole was reduced in comparison to the specimens with drilled hole, due to the increased fibre misalignment angle following the pin insertion procedure. An improvement on the bearing strength of moulded-in hole specimens might be developed if the specimen dimensions would be prepared for a net-tension mode of failure where the fibre misalignment would not have an effect as significant as in the case of bearing failure mode, but this mode should be avoided since it leads to sudden catastrophic failures.

Replication of microchannel structures in WC-Co feedstock using elastomeric replica moulds by hot embossing process.

PubMed

Sahli, M; Gelin, J-C; Barrière, T

2015-10-01

Hot embossing is a net shaping process that is able to produce the micro-components of polymers with intrinsic and complex shapes at lower cost compared with machining and injection moulding. However, the emboss of hard metals, such as WC-Co, is more challenging due to their high thermal conductivity and ease of agglomeration. Thus, a WC-Co alloy mixed with a wax-based binder feedstock was selected. The formed feedstock exhibited pseudo-plastic flow and was successfully embossed (green part). Here, we developed a novel process that is used to replicate polymer microfluidic chips while simultaneously reducing the channel surface roughness of the mould insert, yielding optical-grade (less than 100 nm surface roughness) channels and reservoirs. This paper concerns the replication of metallic microfluidic mould inserts in WC-Co and the parameters associated with feedstock formation via a hot embossing process. A suitable formulation for micro-powder hot embossing has been established and characterised by thermogravimetric analyses and measurements of mixing torques to verify and quantify the homogeneity of the proposed feedstocks. The relative density of the samples increased with processing temperature, and almost fully dense materials were obtained. In this work, the effects of the sintering temperature on the physical properties were systematically analysed. The evolution of the metal surface morphology during the hot embossing process was also investigated. The results indicate that the feedstock can be used to manufacture micro-fluidic die mould cavities with a low roughness, proper dimensions and good shape retention. The shrinkage of the sintered part was approximately 19-24% compared with that of the brown part. Copyright © 2015 Elsevier B.V. All rights reserved.

Numerical simulation of multi-layered textile composite reinforcement forming

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, P.; Hamila, N.; Boisse, P.

2011-05-04

One important perspective in aeronautics is to produce large, thick or/and complex structural composite parts. The forming stage presents an important role during the whole manufacturing process, especially for LCM processes (Liquid Composites Moulding) or CFRTP (Continuous Fibre Reinforcements and Thermoplastic resin). Numerical simulations corresponding to multi-layered composite forming allow the prediction for a successful process to produce the thick parts, and importantly, the positions of the fibres after forming to be known. This paper details a set of simulation examples carried out by using a semi-discrete shell finite element made up of unit woven cells. The internal virtual workmore » is applied on all woven cells of the element taking into account tensions, in-plane shear and bending effects. As one key problem, the contact behaviours of tool/ply and ply/ply are described in the numerical model. The simulation results not only improve our understanding of the multi-layered composite forming process but also point out the importance of the fibre orientation and inter-ply friction during formability.« less

Fabrication of MEMS components using ultrafine-grained aluminium alloys

NASA Astrophysics Data System (ADS)

Qiao, Xiao Guang; Gao, Nong; Moktadir, Zakaria; Kraft, Michael; Starink, Marco J.

2010-04-01

A novel process for the fabrication of a microelectromechanical systems (MEMS) metallic component with features smaller than 10 µm and high thermal conductivity was investigated. This may be applied to new or improved microscale components, such as (micro-) heat exchangers. In the first stage of processing, equal channel angular pressing (ECAP) was employed to refine the grain size of commercial purity aluminium (Al-1050) to the ultrafine-grained (UFG) material. Embossing was conducted using a micro silicon mould fabricated by deep reactive ion etching (DRIE). Both cold embossing and hot embossing were performed on the coarse-grained and UFG Al-1050. Cold embossing on UFG Al-1050 led to a partially transferred pattern from the micro silicon mould and high failure rate of the mould. Hot embossing on UFG Al-1050 provided a smooth embossed surface with a fully transferred pattern and a low failure rate of the mould, while hot embossing on the coarse-grained Al-1050 resulted in a rougher surface with shear bands.

Inhibition of ochratoxigenic moulds by Debaryomyces hansenii strains for biopreservation of dry-cured meat products.

PubMed

Andrade, Maria J; Thorsen, Line; Rodríguez, Alicia; Córdoba, Juan J; Jespersen, Lene

2014-01-17

The ability of the osmotolerant yeast Debaryomyces hansenii to inhibit Penicillium nordicum, the most common ochratoxigenic mould encountered in dry-cured meat products, was evaluated. The antagonistic effect of ten D. hansenii strains isolated from dry-cured ham was screened in vitro using malt extract media and meat extract peptone media with the water activity (a(w)) adjusted to 0.97 and 0.90. A significant inhibition of the two tested P. nordicum strains by D. hansenii cells and cell-free supernatants was observed. At 0.97 a(w), increasing D. hansenii inoculum concentrations significantly improved the inhibition of mould growth on solid medium, whereas at 0.90 a(w) this was not always the case. As observed by bright field microscopy, most D. hansenii strains were able to delay P. nordicum spore germination when co-cultured in malt extract broth. D. hansenii FHSCC 253H showed the highest overall in vitro inhibition of ochratoxigenic mould growth, and was therefore chosen for co-cultivation assays in dry-cured ham slices incubated at 0.94 and 0.84 a(w) simulating ham ripening. Regardless of the experimental conditions tested, lower levels of the inoculated P. nordicum strain were detected in co-cultivation batches compared with batches without D. hansenii. The highest level of mould growth inhibition was observed in batches at 0.94 a(w). Ochratoxin A (OTA) production in ham samples was detected by HPLC-MS. Co-culturing of P. nordicum with D. hansenii FHSCC 253H resulted in lower OTA levels compared with control samples without D. hansenii. The decrease of the mycotoxin presence due to D. hansenii FHSCC 253H was more efficient at 0.94 a(w) (OTA was below the detection limit). In conclusion, D. hansenii is potentially suitable as a biopreservative agent for preventing ochratoxigenic mould growth and OTA accumulation in dry-cured meat products. The inoculation of D. hansenii should be made at the beginning of processing (at the end of post salting) when the a(w) of the product is still high (near 0.94). This action in addition to application of appropriate hygienic actions and control of temperature and relative humidity throughout ripening is required to reduce health risks due to OTA exposure. Copyright © 2013 Elsevier B.V. All rights reserved.

Application of response surface methodology (RSM) and genetic algorithm in minimizing warpage on side arm

NASA Astrophysics Data System (ADS)

Raimee, N. A.; Fathullah, M.; Shayfull, Z.; Nasir, S. M.; Hazwan, M. H. M.

2017-09-01

The plastic injection moulding process produces large numbers of parts of high quality with great accuracy and quickly. It has widely used for production of plastic part with various shapes and geometries. Side arm is one of the product using injection moulding to manufacture it. However, there are some difficulties in adjusting the parameter variables which are mould temperature, melt temperature, packing pressure, packing time and cooling time as there are warpage happen at the tip part of side arm. Therefore, the work reported herein is about minimizing warpage on side arm product by optimizing the process parameter using Response Surface Methodology (RSM) and with additional artificial intelligence (AI) method which is Genetic Algorithm (GA).

Injection and injection-compression moulding replication capability for the production of polymer lab-on-a-chip with nano structures

NASA Astrophysics Data System (ADS)

Calaon, M.; Tosello, G.; Garnaes, J.; Hansen, H. N.

2017-10-01

The manufacturing precision and accuracy in the production of polymer lab-on-a-chip components with 100-130 nm deep nanochannels are evaluated using a metrological approach. Replication fidelity on corresponding process fingerprint test nanostructures over different substrates (nickel tool and polymer part) is quantified through traceable atomic force microscope measurements. Dimensions of injection moulded (IM) and injection-compression moulded (ICM) thermoplastic cyclic olefin copolymer nanofeatures are characterized depending on process parameters and four different features positions on a 30  ×  80 mm2 area. Replication capability of IM and ICM technologies are quantified and the products tolerance at the nanometre dimensional scale verified.

The development of thermoplastic fibre based reinforcements for the rotational moulding process

NASA Astrophysics Data System (ADS)

Alemán, D. N. Castellanos; McCourt, M.; Kearns, M. P.; Martin, P. J.; Butterfield, J.

2018-05-01

Rotational moulding is a method used to produce hollow plastic parts through the heating, melting and cooling of polymer powder within a metal mould. A wide range of products are made using this process, such as fluid containment tanks, boats, light weight vehicle bodies and marine buoys. Rotomoulded composites using thermoplastic fibres are of increasing interest to the industry, as they have the potential to significantly improve impact strength, whilst reducing part weight, resulting in a structure that is 100% recyclable compared to a traditional composite. A series of self-reinforced thermoplastic weaves can be used to produce a number of composite structures using the rotational moulding process. This work outlines the improvements obtained from the range of rotomoulded composites structures, as well as preforms that could be used in future rotational moulding work. Characteristics of self-reinforced materials were exploited with the aim of increasing the mechanical properties, preserving the weaves and increasing the nature of the material adhesion. Addition of the fabrics in the cooling stage was shown to be of great interest as this avoided exposure of the material to the peak temperature, which may affect the integrity of the fabric. Placing the weave during cooling was useful as the material could receive the maximum amount of tensile force during the impact test. A total of nine diverse types of compounds were manufactured and tested, with seven of the impact tests showing an increase in strength greater than 50%.

Processing of ultra-high molecular weight polyethylene/graphite composites by ultrasonic injection moulding: Taguchi optimization.

PubMed

Sánchez-Sánchez, Xavier; Elias-Zuñiga, Alex; Hernández-Avila, Marcelo

2018-06-01

Ultrasonic injection moulding was confirmed as an efficient processing technique for manufacturing ultra-high molecular weight polyethylene (UHMWPE)/graphite composites. Graphite contents of 1 wt%, 5 wt%, and 7 wt% were mechanically pre-mixed with UHMWPE powder, and each mixture was pressed at 135 °C. A precise quantity of the pre-composites mixtures cut into irregularly shaped small pieces were subjected to ultrasonic injection moulding to fabricate small tensile specimens. The Taguchi method was applied to achieve the optimal level of ultrasonic moulding parameters and to maximize the tensile strength of the composites; the results showed that mould temperature was the most significant parameter, followed by the graphite content and the plunger profile. The observed improvement in tensile strength in the specimen with 1 wt% graphite was of 8.8% and all composites showed an increase in the tensile modulus. Even though the presence of graphite produced a decrease in the crystallinity of all the samples, their thermal stability was considerably higher than that of pure UHMWPE. X-ray diffraction and scanning electron microscopy confirmed the exfoliation and dispersion of the graphite as a function of the ultrasonic processing. Fourier transform infrared spectra showed that the addition of graphite did not influence the molecular structure of the polymer matrix. Further, the ultrasonic energy led oxidative degradation and chain scission in the polymer. Copyright © 2018 Elsevier B.V. All rights reserved.

Influence of processing history on the mechanical properties and electrical resistivity of polycarbonate - multi-walled carbon nanotubes nanocomposites

NASA Astrophysics Data System (ADS)

Choong, Gabriel Y. H.; De Focatiis, Davide S. A.

2015-05-01

In this work we investigate the effects of compounding temperature and secondary melt processing on the mechanical response and electrical behaviour of polycarbonate filled with 3 wt% carbon nanotubes. The nanocomposites were melt compounded in an industrial setting at a range of temperatures, and subsequently injection moulded or compression moulded. The surface hardness, uniaxial tensile properties and electrical resistivity were measured. Secondary melt processing is found to be the dominant process in determining the final mechanical properties and resistivity of these materials.

Characterisation and detection of spoilage mould responsible for black spot in dry-cured fermented sausages.

PubMed

Lozano-Ojalvo, Daniel; Rodríguez, Alicia; Cordero, Mirian; Bernáldez, Victoria; Reyes-Prieto, Mariana; Córdoba, Juan J

2015-02-01

Moulds responsible for black spot spoilage of dry-cured fermented sausages were characterised. For this purpose, samples were taken from those dry-cured fermented sausages which showed black spot alteration. Most of the mould strains were first tentatively identified as Penicillium spp. due to their morphological characteristics in different culture conditions, with one strain as Cladosporium sp. The Cladosporium strain was the only one which provoked blackening in culture media. This strain was further characterised by sequencing of ITS1-5.8S-ITS2 rRNA and β-tubulin genes. This mould strain was able to reproduce black spot formation in dry-cured fermented sausage 'salchichón' throughout the ripening process. In addition, a specific and sensitive real-time PCR method was also developed to detect Cladosporium oxysporum responsible for the black spot formation in sausages. This method could be of great interest for the meat industry to detect samples contaminated with this mould before spoilage of product avoiding economic losses for this sector.

Slime mould processors, logic gates and sensors.

PubMed

Adamatzky, A

2015-07-28

A heterotic, or hybrid, computation implies that two or more substrates of different physical nature are merged into a single device with indistinguishable parts. These hybrid devices then undertake coherent acts on programmable and sensible processing of information. We study the potential of heterotic computers using slime mould acting under the guidance of chemical, mechanical and optical stimuli. Plasmodium of acellular slime mould Physarum polycephalum is a gigantic single cell visible to the unaided eye. The cell shows a rich spectrum of behavioural morphological patterns in response to changing environmental conditions. Given data represented by chemical or physical stimuli, we can employ and modify the behaviour of the slime mould to make it solve a range of computing and sensing tasks. We overview results of laboratory experimental studies on prototyping of the slime mould morphological processors for approximation of Voronoi diagrams, planar shapes and solving mazes, and discuss logic gates implemented via collision of active growing zones and tactile responses of P. polycephalum. We also overview a range of electronic components--memristor, chemical, tactile and colour sensors-made of the slime mould. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Metal Injection Moulding: A Near Net Shape Fabrication Method for the Manufacture of Turbine Engine Component

DTIC Science & Technology

2006-05-01

on the processing and characterization of Inconel 625 LPIM material are presented. In depth microstructural characterization was performed on the...annealing. 1 INTRODUCTION Nickel superalloys such as Inconel 625 were developed to withstand the intense conditions present in gas turbine engines...aeronautic parts. A low- pressure injection moulding process, LPIM, has been developed for the fabrication of parts made of Inconel 625 , which maximizes

The Particle Distribution in Liquid Metal with Ceramic Particles Mould Filling Process

NASA Astrophysics Data System (ADS)

Dong, Qi; Xing, Shu-ming

2017-09-01

Adding ceramic particles in the plate hammer is an effective method to increase the wear resistance of the hammer. The liquid phase method is based on the “with the flow of mixed liquid forging composite preparation of ZTA ceramic particle reinforced high chromium cast iron hammer. Preparation method for this system is using CFD simulation analysis the particles distribution of flow mixing and filling process. Taking the 30% volume fraction of ZTA ceramic composite of high chromium cast iron hammer as example, by changing the speed of liquid metal viscosity to control and make reasonable predictions of particles distribution before solidification.

Preoperative planning with three-dimensional reconstruction of patient's anatomy, rapid prototyping and simulation for endoscopic mitral valve repair.

PubMed

Sardari Nia, Peyman; Heuts, Samuel; Daemen, Jean; Luyten, Peter; Vainer, Jindrich; Hoorntje, Jan; Cheriex, Emile; Maessen, Jos

2017-02-01

Mitral valve repair performed by an experienced surgeon is superior to mitral valve replacement for degenerative mitral valve disease; however, many surgeons are still deterred from adapting this procedure because of a steep learning curve. Simulation-based training and planning could improve the surgical performance and reduce the learning curve. The aim of this study was to develop a patient-specific simulation for mitral valve repair and provide a proof of concept of personalized medicine in a patient prospectively planned for mitral valve surgery. A 65-year old male with severe symptomatic mitral valve regurgitation was referred to our mitral valve heart team. On the basis of three-dimensional (3D) transoesophageal echocardiography and computed tomography, 3D reconstructions of the patient's anatomy were constructed. By navigating through these reconstructions, the repair options and surgical access were chosen (minimally invasive repair). Using rapid prototyping and negative mould fabrication, we developed a process to cast a patient-specific mitral valve silicone replica for preoperative repair in a high-fidelity simulator. Mitral valve and negative mould were printed in systole to capture the pathology when the valve closes. A patient-specific mitral valve silicone replica was casted and mounted in the simulator. All repair techniques could be performed in the simulator to choose the best repair strategy. As the valve was printed in systole, no special testing other than adjusting the coaptation area was required. Subsequently, the patient was operated, mitral valve pathology was validated and repair was successfully done as in the simulation. The patient-specific simulation and planning could be applied for surgical training, starting the (minimally invasive) mitral valve repair programme, planning of complex cases and the evaluation of new interventional techniques. The personalized medicine could be a possible pathway towards enhancing reproducibility, patient's safety and effectiveness of a complex surgical procedure. © The Author 2016. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Effect of ageing on the calibration of ballistic gelatin.

PubMed

Guey, Jason; Rodrigues, S; Pullen, A; Shaw, B; Kieser, D C

2018-02-27

Ballistic gelatin is commonly used as a validated surrogate for soft tissue during terminal ballistic testing. However, the effect of a delay between production and testing of a gelatin mould remains unknown. The aim of this study was to determine any potential effects of ageing on ballistic gelatin. Depth of penetration (DoP) of 4.5 mm spherical fragment simulating projectiles was ascertained using mixtures of 10%, 11.25% and 20% Type A 250 Bloom ballistic gelatin. Testing was performed daily for 5 days using velocities between 75 and 210 m/s. DoP at day 5 was statistically compared with day 1, and net mass change was recorded daily. No significant difference was found for DoP observed with time in any of the samples (P>0.05). Spearman correlation was excellent in all moulds. The moulds with known standard calibrations remained in calibration throughout the study period. Mass loss of less than 1% was noted in all samples. Mass loss was the only quantifiable measure of changes in the blocks with time, but did not correlate with any changes in DoP. This may provide reassurance when undertaking such testing that an inadvertent delay will not significantly alter the penetration properties of the mould. Future research is recommended to determine any potential effect on the mechanical properties of gelatin at higher velocity impacts and whether the calibration corresponds to an adequate simulation under such conditions. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

RTM Production Monitoring of the A380 Hinge Arm Droop Nose Mechanism: A Multi-Sensor Approach.

PubMed

Chiesura, Gabriele; Lamberti, Alfredo; Yang, Yang; Luyckx, Geert; Van Paepegem, Wim; Vanlanduit, Steve; Vanfleteren, Jan; Degrieck, Joris

2016-06-14

This research presents a case study of production monitoring on an aerospace composite component: the hinge arm of the droop nose mechanism on the Airbus A380 wing leading edge. A sensor network composed of Fibre Bragg Gratings, capacitive sensors for cure monitoring and thermocouples was embedded in its fibre reinforced lay-up and measurements were acquired throughout its Resin Transfer Moulding production process. Two main challenges had to be overcome: first, the integration of the sensor lines in the existing Resin Transfer Moulding mould without modifying it; second, the demoulding of the component without damaging the sensor lines. The proposed embedding solution has proved successful. The wavelength shifts of the Fibre Bragg Gratings were observed from the initial production stages, over the resin injection, the complete curing of the resin and the cooling-down prior to demoulding. The sensors proved to be sensitive to detecting the resin flow front, vacuum and pressure increase into the mould and the temperature increase caused by the resin curing. Measurements were also acquired during the post-curing cycle. Residual strains during all steps of the process were derived from the sensors' wavelength shift, showing values up to 0.2% in compression. Moreover, the capacitive sensors were able to follow-up the curing degree during the production process. The sensors proved able to detect the resin flow front, whereas thermocouples could not measure an appreciable increase of temperature due to the fact that the resin had the same temperature as the mould.

RTM Production Monitoring of the A380 Hinge Arm Droop Nose Mechanism: A Multi-Sensor Approach

PubMed Central

Chiesura, Gabriele; Lamberti, Alfredo; Yang, Yang; Luyckx, Geert; Van Paepegem, Wim; Vanlanduit, Steve; Vanfleteren, Jan; Degrieck, Joris

2016-01-01

This research presents a case study of production monitoring on an aerospace composite component: the hinge arm of the droop nose mechanism on the Airbus A380 wing leading edge. A sensor network composed of Fibre Bragg Gratings, capacitive sensors for cure monitoring and thermocouples was embedded in its fibre reinforced lay-up and measurements were acquired throughout its Resin Transfer Moulding production process. Two main challenges had to be overcome: first, the integration of the sensor lines in the existing Resin Transfer Moulding mould without modifying it; second, the demoulding of the component without damaging the sensor lines. The proposed embedding solution has proved successful. The wavelength shifts of the Fibre Bragg Gratings were observed from the initial production stages, over the resin injection, the complete curing of the resin and the cooling-down prior to demoulding. The sensors proved to be sensitive to detecting the resin flow front, vacuum and pressure increase into the mould and the temperature increase caused by the resin curing. Measurements were also acquired during the post-curing cycle. Residual strains during all steps of the process were derived from the sensors’ wavelength shift, showing values up to 0.2% in compression. Moreover, the capacitive sensors were able to follow-up the curing degree during the production process. The sensors proved able to detect the resin flow front, whereas thermocouples could not measure an appreciable increase of temperature due to the fact that the resin had the same temperature as the mould. PMID:27314347

Applications for carbon fibre recovered from composites

NASA Astrophysics Data System (ADS)

Pickering; Liu, Z.; Turner, TA; Wong, KH

2016-07-01

Commercial operations to recover carbon fibre from waste composites are now developing and as more recovered fibre becomes available new applications for recovered fibre are required. Opportunities to use recovered carbon fibre as a structural reinforcement are considered involving the use of wet lay processes to produce nonwoven mats. Mats with random in-plane fibre orientation can readily be produced using existing commercial processes. However, the fibre volume fraction, and hence the mechanical properties that can be achieved, result in composites with limited mechanical properties. Fibre volume fractions of 40% can be achieved with high moulding pressures of over 100 bar, however, moulding at these pressures results in substantial fibre breakage which reduces the mean fibre length and the properties of the composite manufactured. Nonwoven mats made from aligned, short carbon fibres can achieve higher fibre volume fractions with lower fibre breakage even at high moulding pressure. A process for aligning short fibres is described and a composite of over 60% fibre volume fraction has been manufactured at a pressures up to 100 bar with low fibre breakage. Further developments of the alignment process have been undertaken and a composite of 46% fibre volume fraction has been produced moulded at a pressure of 7 bar in an autoclave, exhibiting good mechanical properties that compete with higher grade materials. This demonstrates the potential for high value applications for recovered carbon fibre by fibre alignment.

3D printed mitral valve models: affordable simulation for robotic mitral valve repair.

PubMed

Premyodhin, Ned; Mandair, Divneet; Ferng, Alice S; Leach, Timothy S; Palsma, Ryan P; Albanna, Mohammad Z; Khalpey, Zain I

2018-01-01

3D printed mitral valve (MV) models that capture the suture response of real tissue may be utilized as surgical training tools. Leveraging clinical imaging modalities, 3D computerized modelling and 3D printing technology to produce affordable models complements currently available virtual simulators and paves the way for patient- and pathology-specific preoperative rehearsal. We used polyvinyl alcohol, a dissolvable thermoplastic, to 3D print moulds that were casted with liquid platinum-cure silicone yielding flexible, low-cost MV models capable of simulating valvular tissue. Silicone-moulded MV models were fabricated for 2 morphologies: the normal MV and the P2 flail. The moulded valves were plication and suture tested in a laparoscopic trainer box with a da Vinci Si robotic surgical system. One cardiothoracic surgery fellow and 1 attending surgeon qualitatively evaluated the ability of the valves to recapitulate tissue feel through surveys utilizing the 5-point Likert-type scale to grade impressions of the valves. Valves produced with the moulding and casting method maintained anatomical dimensions within 3% of directly 3D printed acrylonitrile butadiene styrene controls for both morphologies. Likert-type scale mean scores corresponded with a realistic material response to sutures (5.0/5), tensile strength that is similar to real MV tissue (5.0/5) and anatomical appearance resembling real MVs (5.0/5), indicating that evaluators 'agreed' that these aspects of the model were appropriate for training. Evaluators 'somewhat agreed' that the overall model durability was appropriate for training (4.0/5) due to the mounting design. Qualitative differences in repair quality were notable between fellow and attending surgeon. 3D computer-aided design, 3D printing and fabrication techniques can be applied to fabricate affordable, high-quality educational models for technical training that are capable of differentiating proficiency levels among users. © The Author 2017. Published by Oxford University Press on behalf of the European Association for Cardio-Thoracic Surgery. All rights reserved.

Slumped glass optics for x-ray telescopes: advances in the hot slumping assisted by pressure

NASA Astrophysics Data System (ADS)

Salmaso, B.; Brizzolari, C.; Basso, S.; Civitani, M.; Ghigo, M.; Pareschi, G.; Spiga, D.; Tagliaferri, G.; Vecchi, G.

2015-09-01

Slumped Glass Optics is a viable solution to build future X-ray telescopes. In our laboratories we use a direct hot slumping approach assisted by pressure, in which the glass optical surface is in contact with the mould, and a pressure is applied to enforce the replication of the mould shape on the glass optical surface. Several prototypes have been already produced and tested in X-rays, showing a continuous improvement in our technology. In this paper, we present the advances in our technology, in terms of slumped glass foils quality and expected performances upon an ideal integration. By using Eagle XG glass foils and Zerodur K20 for the slumping mould, we have fine tuned several process parameters: we present a critical analysis correlating the changes in the process to the improvements in different spatial frequency ranges encompassing the profile and roughness measurements. The use of a re-polished K20 mould, together with the optimized process parameters, lead to the latest result of glass foils with expected performance of less than 3 arcsec in single reflection at 1 keV X-ray energy. This work presents all the relevant steps forward in the hot slumping technology assisted by pressure, aimed at reaching angular resolutions of 5 arcsec for the whole mirror assembly.

Hot granules medium pressure forming process of AA7075 conical parts

NASA Astrophysics Data System (ADS)

Dong, Guojiang; Zhao, Changcai; Peng, Yaxin; Li, Ying

2015-05-01

High strength aluminum alloy plate has a low elongation at room temperature, which leads to the forming of its components need a high temperature. Liquid or gas is used as the pressure-transfer medium in the existing flexible mould forming process, the heat resistance of the medium and pressurizing device makes the application of aluminum alloy plate thermoforming restricted. To solve this problem, the existing medium is replaced by the heat-resisting solid granules and the general pressure equipments are applied. Based on the pressure-transfer performance test of the solid granules medium, the feasibility that the assumption of the extended Drucker-Prager linear model can be used in the finite element analysis is proved. The constitutive equation, the yield function and the theoretical forming limit diagram(FLD) of AA7075 sheet are established. Through the finite element numerical simulation of hot granules medium pressure forming(HGMF) process, not only the influence laws of the process parameters, such as forming temperature, the blank-holder gap and the diameter of the slab, on sheet metal forming performance are discussed, but also the broken area of the forming process is analyzed and predicted, which are coincided with the technological test. The conical part whose half cone angle is 15° and relative height H/d 0 is 0.57, is formed in one process at 250°C. The HGMF process solves the problems of loading and seal in the existing flexible mould forming process and provides a novel technology for thermoforming of light alloy plate, such as magnesium alloy, aluminium alloy and titanium alloy.

The effect of casting conditions on the biaxial flexural strength of glass-ceramic materials.

PubMed

Johnson, A; Shareef, M Y; Walsh, J M; Hatton, P V; van Noort, R; Hill, R G

1998-11-01

To assess the effect of mould and glass casting temperatures on the biaxial flexural strength (BFS) of two different types of castable glass-ceramic, using existing laboratory equipment and techniques. Two castable glass-ceramic materials were evaluated. One glass (LG3) is based on SiO2-Al2O3-P2O5-CaO-CaF2, and is similar in composition to glasses used in the manufacture of glass-ionomer cements. The other glass (SG3) is based on SiO2-K2O-Na2O-CaO-CaF2, and is a canasite-based material. Both materials were used to produce discs of 12 mm diameter and 2 mm thickness using the same lost-wax casting process as used for metal castings. Mould temperatures of between 500 degrees C and 1000 degrees C and glass casting temperatures of between 1100 degrees C and 1450 degrees C were evaluated. The cast discs were cerammed and the biaxial flexural strength determined with a Lloyd 2000 R tester. A significant difference was found for the BFS in the range of mould temperatures evaluated, with the optimum investment mould temperature being 590 degrees C for LG3 and 610 degrees C for SG3 (p = 0.0002 and p = 0.019, respectively). No significant differences were seen between any of the glass casting temperatures evaluated. The mould temperature for castable glass-ceramic materials produced using the lost-wax casting process can have a significant effect on BFS. The optimum mould temperature may differ slightly depending on the type of material being used. The glass casting temperature of these materials does not appear to have a significant effect on BFS.

Cellular automaton model of crowd evacuation inspired by slime mould

NASA Astrophysics Data System (ADS)

Kalogeiton, V. S.; Papadopoulos, D. P.; Georgilas, I. P.; Sirakoulis, G. Ch.; Adamatzky, A. I.

2015-04-01

In all the living organisms, the self-preservation behaviour is almost universal. Even the most simple of living organisms, like slime mould, is typically under intense selective pressure to evolve a response to ensure their evolution and safety in the best possible way. On the other hand, evacuation of a place can be easily characterized as one of the most stressful situations for the individuals taking part on it. Taking inspiration from the slime mould behaviour, we are introducing a computational bio-inspired model crowd evacuation model. Cellular Automata (CA) were selected as a fully parallel advanced computation tool able to mimic the Physarum's behaviour. In particular, the proposed CA model takes into account while mimicking the Physarum foraging process, the food diffusion, the organism's growth, the creation of tubes for each organism, the selection of optimum tube for each human in correspondence to the crowd evacuation under study and finally, the movement of all humans at each time step towards near exit. To test the model's efficiency and robustness, several simulation scenarios were proposed both in virtual and real-life indoor environments (namely, the first floor of office building B of the Department of Electrical and Computer Engineering of Democritus University of Thrace). The proposed model is further evaluated in a purely quantitative way by comparing the simulation results with the corresponding ones from the bibliography taken by real data. The examined fundamental diagrams of velocity-density and flow-density are found in full agreement with many of the already published corresponding results proving the adequacy, the fitness and the resulting dynamics of the model. Finally, several real Physarum experiments were conducted in an archetype of the aforementioned real-life environment proving at last that the proposed model succeeded in reproducing sufficiently the Physarum's recorded behaviour derived from observation of the aforementioned biological laboratory experiments.

Chemorheology of highly filled thermosets: Effects of fillers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Halley, P.J.

1996-12-31

Highly filled thermosets are utilised in the manufacture of many high value added products in the aerospace, communication, computer and automobile industries. A fundamental understanding of the processing of these materials has, however, been hindered by the inherent complexities of the flow and cure properties of these composite thermoset materials. A chemorheological (gel point and chemoviscosity) testing procedure is described here that uses dynamic multiwave tests on a modified Rheometrics RDSII system, using a filled epoxy moulding compound (EMC). Data from this testing procedure has been combined with physical property and kinetic data to produce realistic simulation results using flowmore » simulation software (TSET; MOLDFLOW Pty Ltd). This chemorheological testing procedure has now been successfully implemented commercially by MOLDFLOW Pty Ltd.« less

Design And Development The Ixo Mirrors By Innovative Slumping Glass Technologies

NASA Astrophysics Data System (ADS)

Pareschi, Giovanni; Ghigo, M.; Basso, S.; Citterio, O.; Canestrari, R.; Dell'Orto, E.; Conconi, P.; Parodi, G.; Proserpio, L.

2009-01-01

At INAF Brera Astronomical Observatory development activities are ongoing aiming at the design and development of the IXO mirrors based on slumping glass technique. Our approach is based on the use of thermal slumping of thin glass optics and it presents a number of innovative solution for the implementation. In particular our approach foresees the use of a ceramic mould made of SiC for thermal shaping of the glass segments, which occurs exerting a proper pressure during the moulding process. A thin layer (a few hundred Angstroms) of Pt or Ir is previously deposited on the glass segment, to prevent the adhesion on the SiC mould surface. Therefore this coating not only acts as a release agent of the process but, at the same time, it has also the role of reflecting layer of the X-ray mirror (in a sense like it was the role of gold in the Ni electroforming replication method used for the XMM shells). SiC is chosen for its very good T/M characteristics and, in particular, a very high thermal conductivity and very low CTE. SiC mould will be produced via injection moulding process, followed by a the application of a cladding layer (a few tens microns) application of CVD SiC for allowing a superpolishing of the surface until a roughness of a few Angstrom rms is achieved. Once the mirror segments are produced, they are integrated in petals by means of air-bearings supports, that allows us to maintain the proper shape of the segments without deformations. The segments are stacked into the petals by the use of connecting ribs, glued to the front surface of each mirror and to the rear of the next one.

Electroplating moulds using dry film thick negative photoresist

NASA Astrophysics Data System (ADS)

Kukharenka, E.; Farooqui, M. M.; Grigore, L.; Kraft, M.; Hollinshead, N.

2003-07-01

This paper reports on progress on the feasibility of fabricating moulds for electroplating using Ordyl P-50100 (negative) acrylate polymer based dry film photoresist, commercially available from Elga Europe (http://www.elgaeurope.it). We used this photoresist as an alternative to SU8 negative epoxy based photoresist, which is very difficult to process and remove after electroplating (Lorenz et al 1998 Microelectron. Eng. 41/42 371-4, Eyre et al 1998 Proc. MEMS'98 (Heidelberg) (Piscataway, NJ: IEEE) pp 218-22). Ordyl P-50100 is easy to work with and can be easily removed after processing. A single layer of Ordyl P-50100 was deposited by lamination up to 20 µm thickness. Thicker layers (200 µm and more) can be achieved with multilayer lamination using a manual laminator. For our applications we found that Ordyl P-50100 dry film photoresist is a very good alternative to SU8 for the realization of 100 µm high moulds. The results presented will open up new possibilities for low-cost LIGA-type processes for MEMS applications.

Utilizing of inner porous structure in injection moulds for application of special cooling method

NASA Astrophysics Data System (ADS)

Seidl, M.; Bobek, J.; Šafka, J.; Habr, J.; Nováková, I.; Běhálek, L.

2016-04-01

The article is focused on impact evaluation of controlled inner structure of production tools and new cooling method on regulation of thermal processes for injection moulding technology. The mould inserts with porous structure were cooled by means of liquid CO2 which is very progressive cooling method and enables very fast and intensive heat transfer among the plastic product, the production tool and cooling medium. The inserts were created using rapid prototype technology (DLSM) and they had a bi-component structure consisting of thin compact surface layer and defined porous inner structure of open cell character where liquid CO2 was flowing through. This analyse includes the evaluation of cooling efficiency for different inner structures and different time profiles for dosing of liquid CO2 into the porous structure. The thermal processes were monitored using thermocouples and IR thermal analyse of product surface and experimental device. Intensive heat removal influenced also the final structure and the shape and dimensional accuracy of the moulded parts that were made of semi-crystalline polymer. The range of final impacts of using intensive cooling method on the plastic parts was defined by DSC and dimensional analyses.

Optimisation of warpage on thin shell plastic part using response surface methodology (RSM) and glowworm swarm optimisation (GSO)

NASA Astrophysics Data System (ADS)

Asyirah, B. N.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Hazwan, M. H. M.

2017-09-01

In manufacturing a variety of parts, plastic injection moulding is widely use. The injection moulding process parameters have played important role that affects the product's quality and productivity. There are many approaches in minimising the warpage ans shrinkage such as artificial neural network, genetic algorithm, glowworm swarm optimisation and hybrid approaches are addressed. In this paper, a systematic methodology for determining a warpage and shrinkage in injection moulding process especially in thin shell plastic parts are presented. To identify the effects of the machining parameters on the warpage and shrinkage value, response surface methodology is applied. In thos study, a part of electronic night lamp are chosen as the model. Firstly, experimental design were used to determine the injection parameters on warpage for different thickness value. The software used to analyse the warpage is Autodesk Moldflow Insight (AMI) 2012.

Digital dental surface registration with laser scanner for orthodontics set-up planning

NASA Astrophysics Data System (ADS)

Alcaniz-Raya, Mariano L.; Albalat, Salvador E.; Grau Colomer, Vincente; Monserrat, Carlos A.

1997-05-01

We present an optical measuring system based on laser structured light suitable for its diary use in orthodontics clinics that fit four main requirements: (1) to avoid use of stone models, (2) to automatically discriminate geometric points belonging to teeth and gum, (3) to automatically calculate diagnostic parameters used by orthodontists, (4) to make use of low cost and easy to use technology for future commercial use. Proposed technique is based in the use of hydrocolloids mould used by orthodontists for stone model obtention. These mould of the inside of patient's mouth are composed of very fluent materials like alginate or hydrocolloids that reveal fine details of dental anatomy. Alginate mould are both very easy to obtain and very low costly. Once captured, alginate moulds are digitized by mean of a newly developed and patented 3D dental scanner. Developed scanner is based in the optical triangulation method based in the projection of a laser line on the alginate mould surface. Line deformation gives uncalibrated shape information. Relative linear movements of the mould with respect to the sensor head gives more sections thus obtaining a full 3D uncalibrated dentition model. Developed device makes use of redundant CCD in the sensor head and servocontrolled linear axis for mould movement. Last step is calibration to get a real and precise X, Y, Z image. All the process is done automatically. The scanner has been specially adapted for 3D dental anatomy capturing in order to fulfill specific requirements such as: scanning time, accuracy, security and correct acquisition of 'hidden points' in alginate mould. Measurement realized on phantoms with known geometry quite similar to dental anatomy present errors less than 0,1 mm. Scanning of global dental anatomy is 2 minutes, and generation of 3D graphics of dental cast takes approximately 30 seconds in a Pentium-based PC.

Using special additions to preparation of the moulding mixture for casting steel parts of drive wheel type

NASA Astrophysics Data System (ADS)

Josan, A.; Pinca Bretotean, C.

2015-06-01

The paper presents the possibility of using special additions to the execution of moulding mixtures for steel castings, drive wheel type. Critical analysis of moulding technology leads to the idea that most defects appear due to using improper moulding mixture. Using a improper moulding mixture leads to penetration of steel in moulding mixture, resulting in the formation of adherences, due to inadequate refractarity of the mould and core mixtures. Using only the unique mixture to the moulding leads to increasing consumption of new sand, respectively to the increase of price of piece. Acording to the dates registered in the industrial practice is necessary to use the special additions to obtain the moulding mixtures, carbonaceous materials respectively.

Use of the selective agar medium CREAD for monitoring the level of airborne spoilage moulds in cheese production.

PubMed

Kure, Cathrine Finne; Borch, Elisabeth; Karlsson, Ingela; Homleid, Jens Petter; Langsrud, Solveig

2008-02-29

It was investigated if a selective medium for common cheese spoiling moulds (CREAD) could give more relevant information than a general mould medium in hygienic air-sampling in cheese factories. A total of 126 air-samples were taken in six Nordic cheese factories using the general mould medium DG18 and CREAD. The level and genera of air-borne mould was determined. Identification to species-level was performed for a selection of samples. In five cheese factories the mycobiota was dominated by Penicillium spp. and in one cheese factory by Cladosporium spp. The concentration of air-borne moulds varied between the cheese factories ranging from 1 to 270 cfu/m3 on DG18 with a median value of 17. The number of mould colonies was in general lower at CREAD. Identification indicated that CREAD supported growth of common spoilage moulds for cheese, such as Penicillium palitans and P. commune. The mycobiota on DG18 also consisted of moulds not commonly associated with spoilage of cheese, such as Cladosporium spp., P. brevicompactum and P. chrysogenum. Contamination of cheese with mould is periodically a problem in production of semi-hard cheese and the level of air-borne mould is therefore routinely monitored in cheese factories. A clear correlation between the total number of moulds in air and mould growth on products is not always found. The conclusion from the investigation is that it is recommended to use a selective medium for cheese spoilage moulds, such as CREAD in hygienic monitoring.

Thermal homogeneity of plastication processes in single-screw extruders

NASA Astrophysics Data System (ADS)

Bu, L. X.; Agbessi, Y.; Béreaux, Y.; Charmeau, J.-Y.

2018-05-01

Single-screw plastication, used in extrusion and in injection moulding, is a major way of processing commodity thermoplastics. During the plastication phase, the polymeric material is melted by the combined effects of shear-induced self-heating (viscous dissipation) and heat conduction coming from the barrel. In injection moulding, a high level of reliability is usually achieved that makes this process ideally suited to mass market production. Nonetheless, process fluctuations still appear that make moulded part quality control an everyday issue. In this work, we used a combined modelling of plastication, throughput calculation and laminar dispersion, to investigate if, and how, thermal fluctuations could propagate along the screw length and affect the melt homogeneity at the end of the metering section. To do this, we used plastication models to relate changes in processing parameters to changes in the plastication length. Moreover, a simple model of throughput calculation is used to relate the screw geometry, the polymer rheology and the processing parameters to get a good estimate of the mass flow rate. Hence, we found that the typical residence time in a single screw is around one tenth of the thermal diffusion time scale. This residence time is too short for the dispersion coefficient to reach a steady state, but too long to be able to neglect radial thermal diffusion and resort to a purely convective solution. Therefore, a full diffusion/convection problem has to be solved with a base flow described by the classic pressure and drag velocity field. Preliminary results already show the major importance of the processing parameters in the breakthrough curve of an arbitrary temperature fluctuation at the end of the metering section of injection moulding screw. When the flow back-pressure is high, the temperature fluctuation is spread more evenly with time, whereas a pressure drop in the flow will results in a breakthrough curve which presents a larger peak of fluctuation.

Energy optimization aspects by injection process technology

NASA Astrophysics Data System (ADS)

Tulbure, A.; Ciortea, M.; Hutanu, C.; Farcas, V.

2016-08-01

In the proposed paper, the authors examine the energy aspects related to the injection moulding process technology in the automotive industry. Theoretical considerations have been validated by experimental measurements on the manufacturing process, for two types of injections moulding machines, hydraulic and electric. Practical measurements have been taken with professional equipment separately on each technological operation: lamination, compression, injection and expansion. For results traceability, the following parameters were, whenever possible, maintained: cycle time, product weight and the relative time. The aim of the investigations was to carry out a professional energy audit with accurate losses identification. Base on technological diagram for each production cycle, at the end of this contribution, some measure to reduce the energy consumption were proposed.

Effect of electrical field strength applied by PEF processing and storage temperature on the outgrowth of yeasts and moulds naturally present in a fresh fruit smoothie.

PubMed

Timmermans, R A H; Nederhoff, A L; Nierop Groot, M N; van Boekel, M A J S; Mastwijk, H C

2016-08-02

Pulsed electrical field (PEF) technology offers an alternative to thermal pasteurisation of high-acid fruit juices, by extending the shelf life of food products, while retaining its fresh taste and nutritional value. Substantial research has been performed on the effect of electrical field strength on the inactivation kinetics of spoilage and pathogenic micro-organisms and on the outgrowth of spoilage micro-organisms during shelf life. However, studies on the effect of electrical field strength on the inactivation and outgrowth of surviving populations during shelf life are missing. In this study, we assessed the influence of electrical field strength applied by PEF processing and storage temperature on the outgrowth of surviving yeast and mould populations naturally present in fresh fruit smoothie in time. Therefore, an apple-strawberry-banana smoothie was treated in a continuous-flow PEF system (130L/h), using similar inlet and outlet conditions (preheating temperature 41°C, maximum temperature 58°C) to assure that the amount of energy across the different conditions was kept constant. Smoothies treated with variable electrical field strengths (13.5, 17.0, 20.0 and 24.0kV/cm) were compared to smoothies without treatment for outgrowth of yeasts and moulds. Outgrowth of yeasts and moulds stored at 4°C and 7°C was analysed by plating and visual observation and yeast growth was modelled using the modified logistic growth model (Zwietering model). Results showed that the intensity of the electrical field strength had an influence on the degree of inactivation of yeast cells, resulting in a faster outgrowth over time at lower electrical field strength. Outgrowth of moulds over time was not affected by the intensity of the electrical field strength used. Application of PEF introduces a trade-off between type of spoilage: in untreated smoothie yeasts lead to spoilage after 8days when stored at 4 or 7°C, whereas in PEF treated smoothie yeasts were (partly) inactivated and provided outgrowth opportunities for moulds, which led to spoilage by moulds after 14days (7°C) or 18days (4°C). Copyright © 2016 Elsevier B.V. All rights reserved.

Antifungal properties of silver nanoparticles against indoor mould growth.

PubMed

Ogar, Anna; Tylko, Grzegorz; Turnau, Katarzyna

2015-07-15

The presence of moulds in indoor environments causes serious diseases and acute or chronic toxicological syndromes. In order to inhibit or prevent the growth of microorganisms on building materials, the disruption of their vital processes or the reduction of reproduction is required. The development of novel techniques that impair the growth of microorganisms on building materials is usually based on silver nanoparticles (AgNPs). It makes them an alternative to other biocides. AgNPs have proven antibacterial activity and became promising in relation to fungi. The aim of the study was to assess growth and morphology of mycelia of typical indoor fungal species: Penicillium brevicompactum, Aspergillus fumigatus, Cladosporium cladosporoides, Chaetomium globosum and Stachybotrys chartarum as well as Mortierella alpina, cultured on agar media. The antifungal activity of AgNPs was also tested in relation to C. globosum and S. chartarum grown on the surface of gypsum drywall. It was found that the presence of AgNPs in concentrations of 30-200mg/l significantly decreased the growth of fungi. However, in the case of M. alpina, AgNPs stimulated its growth. Moreover, strong changes in moulds morphology and colour were observed after administration of AgNPs. Parameters of conidiophores/sporangiophores varied depending on mould region and changed significantly after treatment with AgNPs. The experiments have shown antifungal properties of AgNPs against common indoor mould species. Their application to building materials could effectively protect indoor environments from mould development. However, consideration must be given to the fact that the growth of some fungal strains might be stimulated by AgNPs. Copyright © 2015 Elsevier B.V. All rights reserved.

Hot slumping glass technology for the grazing incidence optics of future missions with particular reference to IXO

NASA Astrophysics Data System (ADS)

Ghigo, M.; Basso, S.; Bavdaz, M.; Conconi, P.; Citterio, O.; Civitani, M.; Friedrich, P.; Gallieni, D.; Guldimann, B.; Martelli, F.; Negri, R.; Pagano, G.; Pareschi, G.; Parodi, G.; Proserpio, L.; Salmaso, B.; Scaglione, F.; Spiga, D.; Tagliaferri, G.; Terzi, L.; Tintori, M.; Vongehr, M.; Wille, E.; Winter, A.; Zambra, A.

2010-07-01

The mirrors of the International X-ray Observatory (IXO) consist of a large number of high quality segments delivering a spatial resolution better than 5 arcsec. A study concerning the slumping of thin glass foils for the IXO mirrors is under development in Europe, funded by ESA and led by the Brera Observatory. We are investigating two approaches, the "Direct" and "Indirect" slumping technologies, being respectively based on the use of convex and concave moulds. In the first case during the thermal cycle the optical surface of the glass is in direct contact with the mould surface, while in the second case it is the rear side of the foil which touches the master. Both approaches present pros and cons and aim of this study is also to make an assessment of both processes and to perform a trade-off between the two. The thin plates are made of D263glass produced by Schott. Each plate is 0.4 mm thick, with a reflecting area of 200 mm x 200 mm; the mould are made of Fused Silica. After the thermal cycle the slumped MPs are characterized to define their optical quality and microroughness. The adopted integration process foresees the bonding of the slumped foils to a rigid backplane by means of reinforcing ribs. During the bonding process the plates are constrained to stay in close contact to the surface of the master (i.e. the same mould used for the hot slumping process) by the application of a vacuum pump suction. In this way spring-back deformations and low frequency errors still present on the foil profile after slumping can be corrected. In this paper we present the preliminary results concerning achieved during the first part of the project.

Mechanical properties of micro-injected HDPE composites

NASA Astrophysics Data System (ADS)

Bongiorno, A.; Pagano, C.; Agnelli, S.; Baldi, F.; Fassi, I.

2016-03-01

Micro-injection moulding is one of the key manufacturing technologies for the mass production of high value polymeric miniaturized-components. However, this process is not just a straightforward down scaling of the conventional injection moulding technique. Indeed, during the micro-injection the polymer melt is forced to flow at high strain rates through very small channels in non-isothermal conditions, and this can lead to complex microstructures and to parts with unexpected performances. In this work, the relationships among the processing conditions, the mechanical properties and the microstructural characteristics of miniaturized specimens obtained by injection moulding were investigated. Two model systems were considered with the same filler content of 15% wt. (HDPE-talc and HDPE-glass beads), representative of two different types of micro-composites: containing lamellar and spherical micro-particles, respectively. The attention was focused on the influence of the filler type and the process conditions on the mechanical behaviour, examined by uniaxial tensile tests and dynamic-mechanical analyses, and on the morphological characteristics of the specimens, examined by microscopy analyses. The results highlight that mechanical response of the miniaturized specimens is significantly affected by both the filler and the process conditions that can have an influence on the polymer microstructure. Lamellar composites showed the best performance due to the orientation of the talc particles during the micro-injection process, while, different morphologies of the skin/core transition region in dependence on the process temperatures were observable.

In-process 3D assessment of micromoulding features

NASA Astrophysics Data System (ADS)

Whiteside, B. R.; Spares, R.; Coates, P. D.

2006-04-01

Micro injection moulding (micromoulding) technology has recently emerged as a viable manufacturing route for polymer, metal and ceramic components with micro-scale features and surface textures. With a cycle time for production of a single component of just a few seconds, the proces offers the capability for mass production of microscale devices at a low marginal cost. However, the extreme stresses, strain rates and temperature gradients characteristic of the process have the consequence that a slight fluctuation in material properties or moulding conditions can have a significant impact on the dimensional or structural properties of the resulting component and in-line process monitoring is highly desirable. This paper describes the development of an in-process, high speed 3-dimensional measurement system for evaluation of every component manufactured during the process. A high speed camera and microscope lens coupled with a linear stage are used to create a stack of images which are subsequently processed using extended depth of field techniques to form a virtual 3-dimensional contour of the component. This data can then be used to visually verify the quality of the moulding on-screen or standard machine vision algorithms can be employed to allow fully automated quality inspection and filtering of sub-standard products. Good results have been obtained for a range of materials and geometries and measurement accuracy has been verified through comparison with data obtained using a Wyko NT1100 white light interferometer.

Research on the influence of moulding-casting technology on the quality of castings

NASA Astrophysics Data System (ADS)

Josan, A.; Pinca Bretotean, C.; Raţiu, S.; Ardelean, E.; Ardelean, M.

2017-05-01

The quality of castings has a particularly role in the Romanian foundries. In this context, quality assurance is the overall objective of the foundries. The paper presents the critical analysis performed on moulding-casting technology of the type Lifting mechanism. This casting is a subset of the lifting and rotating mechanism of the furnace vault. The casting analysed is a medium size, with weight of 114 kg. The current moulding-casting technology involves moulding into three mould-parts leading to the occurrence of defects (decentering of the core, displacement of the lower mould and the middle mould and occurrence of burrs in area separated. Thus, to reduce the percentage of defects registered in industrial practice is necessary to change the moulding-casting technology. This requires the use of two mould-parts, re-dimensioning of the core and the core box and dimensioning of the runner network. The adoption of these changes in industrial practice has direct implications on the cost of casting and foundry costs default.

Warpage analysis on thin shell part using glowworm swarm optimisation (GSO)

NASA Astrophysics Data System (ADS)

Zulhasif, Z.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Hazwan, M. H. M.

2017-09-01

The Autodesk Moldflow Insight (AMI) software was used in this study to focuses on the analysis in plastic injection moulding process associate the input parameter and output parameter. The material used in this study is Acrylonitrile Butadiene Styrene (ABS) as the moulded material to produced the plastic part. The MATLAB sortware is a method was used to find the best setting parameter. The variables was selected in this study were melt temperature, packing pressure, coolant temperature and cooling time.

Experimental study and thermodynamic modelling of the calcium oxide-silicon oxide-aluminum oxide-calcium fluoride system

NASA Astrophysics Data System (ADS)

Kim, Dong-Geun

Mould flux for the continuous casting process is a major concern for the steelmaking industry. Nowadays, more than 90 % of steel is being produced by the continuous casting process, which requires mould flux as an essential additive. The development of mould flux has been achieved by the conventional trial and error approach since it was first introduced in industry in the 1960s. Recently, the interest on the properties of fluorine has increased a lot since it is reported that fluorine has important functions such as playing a critical role on the crystallization behavior, and decreasing the melting point and viscosity of slag. However, the conventional way to find a suitable mould flux is not efficient to face the increasingly stringent requirements of the continuous casting process such as thin slab casting and higher casting speed. Therefore, fundamental phase diagram study on mould flux systems is clearly necessary, and thermodynamic modeling is the most effective way to design new mould flux in terms of time and money saving. The major components of mould flux, the CaO-SiO2-Al2O 3-CaF2 system, are investigated in this study as these four constituents will mostly affect the largest numbers of properties. Unfortunately, fluorine has high volatility at high temperature and high reactivity with other materials. Therefore, the results of previous experiments on F-containing systems are characterized by large discrepancies due to composition alteration and unexpected reactions during the experiment. As literature data show inconsistent results between each other, key phase diagram experiments were performed in this study. The phase diagram experiments were conducted with the quenching method in sealed Pt capsules to prevent fluorine loss during the experiment. The analyses were performed using a FE-SEM equipped with an EDS system, and a newly developed technique which produces more precise quantitative results for the equilibrium phase composition. The CaO liquidus of the CaO-CaF 2 binary system, which the literature data differ from each other by up to 50 mol %, was confirmed. The CaO solubility in solid CaF2 was found for the first time and reaches about 5 mol % at the eutectic temperature. The liquidus of the CaO-Al2O3-CaF2 and CaO-SiO 2-CaF2 systems were carefully studied and the miscibility gap in the CaO-Al2O3-CaF2 system was proved to be much smaller than that reported in literature. Also, thermal analysis was performed using DSC in a Pt crucible. The eutectic temperatures of the CaO-CaF2 and CaAl2O4-CaF2 systems were successfully measured and the alpha to beta-CaF2 polymorphic transition was confirmed. Based on the new experimental data and reliable literature data, thermodynamic modeling of the CaO-SiO2-Al 2O3-CaF2 system was also carried out. The results of thermodynamic calculation can be very beneficial for new mould flux design.

Impregnation quality of shredded semipreg after compression moulding

NASA Astrophysics Data System (ADS)

Vincent, G.; Balakrishnan, V.; de Bruijn, T. A.; Wijskamp, S.; Abdul Rasheed, M. I.

2017-10-01

Manufacturing of thermoplastic composites (TPC) inherently generates scrap, mainly in the form of offcuts or rejected parts. The growth of TPC over recent decades has now reached a point where developing specific recycling solutions for TPC waste has become crucial. While looking at the various steps during which scrap is produced, the nesting of semipreg or prepreg appears to be critical. This work aims to develop a route for recycling semipreg offcuts, comprising shredding and compression moulding. This article focuses on an experimental study of the compression moulding step of carbon fibres reinforced PPS (C/PPS) to investigate the uniformity and impregnation quality of plates. These plates were realised in a picture frame while varying both the fibre volume content between 30% and 50% and the processing parameters. Visual inspection and cross-sectional microscopy were performed to assess the quality of each plate. As a first step, the influence of the type of added matrix (film, powder, pellets) and the type of pre-impregnation (film, powder) was studied. Stacking of polymer powder with shredded powder-coated semipreg gave the best impregnation quality. It was also shown that longer dwell time at melt leads to better consolidation quality. However, the difficulty in obtaining good impregnation comes from the disentangled shredded material, which is composed of three forms: semipreg flakes, dry bundles and pieces of matrix. When dry bundles reach the mould surfaces during the filling of the mould or when they are packed together, the consolidation cycle hardly impregnates them and they remain dry afterwards. Furthermore, large local variations of fibre fraction were noticed, resulting from a random mould filling. Therefore, the recycling solution for shredded semipreg is feasible when the fibre fraction is reduced but improvements on the part variability still have to be made.

3D printing utility for surgical treatment of acetabular fractures.

PubMed

Chana Rodríguez, F; Pérez Mañanes, R; Narbona Cárceles, F J; Gil Martínez, P

2018-05-25

Preoperative 3D modelling enables more effective diagnosis and simulates the surgical procedure. We report twenty cases of acetabular fractures with preoperative planning performed by pre-contouring synthesis plates on a 3D printed mould obtained from a computarized tomography (CT) scan. The mould impression was made with the DaVinci 1.0 printer model (XYZ Printing). After obtaining the printed hemipelvis, we proceeded to select the implant size (pelvic Matta system, Stryker ® ) that matched the characteristics of the fracture and the approach to be used. Printing the moulds took a mean of 385minutes (322-539), and 238grams of plastic were used to print the model (180-410). In all cases, anatomic reduction was obtained and intra-operative changes were not required in the initial contouring of the plates. The time needed to perform the full osteosynthesis, once the fracture had been reduced was 16.9minutes (10-24). In one case fixed with two plates, a postoperative CT scan showed partial contact of the implant with the surface of the quadrilateral plate. In the remaining cases, the contact was complete. In conclusion, our results suggest that the use of preoperative planning, by printing 3D mirror imaging models of the opposite hemipelvis and pre-contouring plates over the mould, might effectively achieve a predefined surgical objective and reduce the inherent risks in these difficult procedures. Copyright © 2018. Publicado por Elsevier España, S.L.U.

The influence of different screw concepts while processing fibre reinforced thermoplastics with the concept of inline-compounding on an injection moulding machine

NASA Astrophysics Data System (ADS)

Moritzer, E.; Müller, E.; Kleeschulte, R.

2014-05-01

Today, the global market poses major challenges for industrial product development. Complexity, the wide range of variants, flexibility and individuality are just some of the features that products have to fulfil. Product series additionally have shorter and shorter lifetimes. Because of their high capacity for adaptation, polymers are increasingly able to substitute traditional materials such as wood, glass and metals in various fields of application [1]. But polymers can only substitute other materials if they are optimally suited to the applications in question. Hence, product-specific material development is becoming increasingly important [2]. The problem is that the traditional development process for new polymer formulations is much too complex, too slow and therefore too expensive. Product-specific material development is thus out of the question for most processors. Integrating the compounding step in the injection moulding process would lead to a more efficient and faster development process for a new polymer formulation, providing an opportunity to create new product-specific materials. This process is called inline-compounding on an injection moulding machine. In order to develop this innovative formulation concept, with the focus on fibre reinforced thermoplastics, different screw-concepts are compared with regard to the resultant performance characteristics in the part, such as mechanical properties and fibre length distribution.

Artificial neural networks to model formulation-property correlations in the process of inline-compounding on an injection moulding machine

NASA Astrophysics Data System (ADS)

Moritzer, Elmar; Müller, Ellen; Martin, Yannick; Kleeschulte, Rainer

2015-05-01

Today the global market poses great challenges for industrial product development. Complexity, diversity of variants, flexibility and individuality are just some of the features that products have to offer today. In addition, the product series have shorter lifetimes. Because of their high capacity for adaption, polymers are increasingly able to displace traditional materials such as wood, glass and metals from various fields of application. Polymers can only be used to substitute other materials, however, if they are optimally suited to the applications in question. Hence, product-specific material development is becoming increasingly important. Integrating the compounding step in the injection moulding process permits a more efficient and faster development process for a new polymer formulation, making it possible to create new product-specific materials. This process is called inline-compounding on an injection moulding machine. The entire process sequence is supported by software from Bayer Technology called Product Design Workbench (PDWB), which provides assistance in all the individual steps from data management, via analysis and model compilation, right through to the optimization of the formulation and the design of experiments. The software is based on artificial neural networks and can model the formulation-property correlations and thus enable different formulations to be optimized. In the study presented, the workflow and the modelling with the software are presented.

Paraffin wax removal from metal injection moulded cocrmo alloy compact by solvent debinding process

NASA Astrophysics Data System (ADS)

Dandang, N. A. N.; Harun, W. S. W.; Khalil, N. Z.; Ahmad, A. H.; Romlay, F. R. M.; Johari, N. A.

2017-10-01

One of the most crucial and time consuming phase in metal injection moulding (MIM) process is “debinding”. These days, in metal injection moulding process, they had recounted that first debinding practice was depend on thermal binder degradation, which demanding more than 200 hours for complete removal of binder. Fortunately, these days world had introduced multi-stage debinding techniques to simplified the debinding time process. This research study variables for solvent debinding which are temperature and soaking time for samples made by MIM CoCrMo powder. Since wax as the key principal in the binder origination, paraffin wax will be removed together with stearic acid from the green bodies. Then, debinding process is conducted at 50, 60 and 70°C for 30-240 minutes. It is carried out in n-heptane solution. Percentage weight loss of the binder were measured. Lastly, scanning electron microscope (SEM) analysis and visual inspection were observed for the surface of brown compact. From the results, samples debound at 70°C exhibited a significant amount of binder loss; nevertheless, sample collapse, brittle surface and cracks were detected. But, at 60°C temperature and time of 4 hours proven finest results as it shows sufficient binder loss, nonappearance of surface cracks and easy to handle. Overall, binder loss is directly related to solvent debinding temperature and time.

Production of thin glass mirrors by hot slumping for x-ray telescopes: present process and ongoing development

NASA Astrophysics Data System (ADS)

Salmaso, B.; Basso, S.; Brizzolari, C.; Civitani, M.; Ghigo, M.; Pareschi, G.; Spiga, D.; Tagliaferri, G.; Vecchi, G.

2014-07-01

Thin glass foils are considered good candidates to build a segmented X-ray telescope with effective area as large as 2 m2 and angular resolution better than 5 arcsec. In order to produce thin glass mirror segments, we developed a direct hot slumping technique assisted by pressure, in which the shape of a mould is replicated onto the optical surface of the glass. In this paper we present the result obtained with AF32 (by Schott) and EAGLE XG (by Corning) glass types. The selected mould material is Zerodur K20, as it does not require any anti-sticking layer and has a good matching, in terms of Coefficient of Thermal Expansion, with both glass types. Our group already produced a few prototypes, reaching angular resolution near 20 arcsec. In this work, relevant steps forward aimed at attaining a 5 arcsec angular resolution are described, along with the tuning of few key parameters in the slumping process. The results obtained on a newly procured cylindrical Zerodur K20 mould are presented.

Thermal and Kinetic Modelling of Elastomer Flow—Application to an Extrusion Die

NASA Astrophysics Data System (ADS)

Launay, J.; Allanic, N.; Mousseau, P.; Deterre, R.

2011-05-01

This paper reports and discusses the thermal and kinetic behaviour of elastomer flow inside an extrusion die. The reaction progress through the runner was modeled by using a particle tracking technique. The aim is to analyze viscous dissipation phenomena to control scorch arisen, improve the rubber compound curing homogeneity and reduce the heating time in the mould using the progress of the induction time. The heat and momentum equations were solved in three dimensions with Ansys Polyflow. A particle tracking technique was set up to calculate the reaction progress. Several simulations were performed to highlight the influence of process parameters and geometry modifications on the rubber compound thermal and cure homogeneity.

Study of mould design and forming process on advanced polymer-matrix composite complex structure

NASA Astrophysics Data System (ADS)

Li, S. J.; Zhan, L. H.; Bai, H. M.; Chen, X. P.; Zhou, Y. Q.

2015-07-01

Advanced carbon fibre-reinforced polymer-matrix composites are widely applied to aviation manufacturing field due to their outstanding performance. In this paper, the mould design and forming process of the complex composite structure were discussed in detail using the hat stiffened structure as an example. The key issues of the moulddesign were analyzed, and the corresponding solutions were also presented. The crucial control points of the forming process such as the determination of materials and stacking sequence, the temperature and pressure route of the co-curing process were introduced. In order to guarantee the forming quality of the composite hat stiffened structure, a mathematical model about the aperture of rubber mandrel was introduced. The study presented in this paper may provide some actual references for the design and manufacture of the important complex composite structures.

Myceliophthora thermophila syn. Sporotrichum thermophile: a thermophilic mould of biotechnological potential.

PubMed

Singh, Bijender

2016-01-01

Myceliophthora thermophila syn. Sporotrichum thermophile is a ubiquitous thermophilic mould with a strong ability to degrade organic matter during optimal growth at 45 °C. Both genome analysis and experimental data have suggested that the mould is capable of hydrolyzing all major polysaccharides found in biomass. The mould is able to secrete a large number of hydrolytic enzymes (cellulases, laccases, xylanases, pectinases, lipases, phytases and some other miscellaneous enzymes) employed in various biotechnological applications. Characterization of the biomass-hydrolyzing activity of wild and recombinant enzymes suggests that this mould is highly efficient in biomass decomposition at both moderate and high temperatures. The native enzymes produced by the mould are more efficient in activity than their mesophilic counterparts beside their low enzyme titers. The mould is able to synthesize various biomolecules, which are used in multifarious applications. Genome sequence data of M. thermophila also supported the physiological data. This review describes the biotechnological potential of thermophilic mould, M. thermophila supported by genomic and experimental evidences.

Fabrication of three-dimensional collagen scaffold using an inverse mould-leaching process.

PubMed

Ahn, SeungHyun; Lee, SuYeon; Cho, Youngseok; Chun, Wook; Kim, GeunHyung

2011-09-01

Natural biopolymers, such as collagen or chitosan, are considered ideal for biomedical scaffolds. However, low processability of the materials has hindered the fabrication of designed pore structures controlled by various solid freeform-fabrication methods. A new technique to fabricate a biomedical three-dimensional collagen scaffold, supplemented with a sacrificial poly(ethylene oxide) mould is proposed. The fabricated collagen scaffold shows a highly porous surface and a three-dimensional structure with high porosity as well as mechanically stable structure. To show its feasibility for biomedical applications, fibroblasts/keratinocytes were co-cultured on the scaffold, and the cell proliferation and cell migration of the scaffold was more favorable than that obtained with a spongy-type collagen scaffold.

The effect of investment type on the fit of cast titanium crowns.

PubMed

Mori, T; Jean-Louis, M; Yabugami, M; Togaya, T

1994-12-01

In order to determine the best laboratory procedure for titanium crown casting, a set of thermal expansion measurements and casting experiments were carried out using a casting machine (argon arc, pressure difference type) and three different investments, two conventional SiO2 based investments and a new Al2O3/MgO based investment. The thermal expansion measurements involved a cycle of heating and cooling. The relatively low mould temperatures recommended (200 degrees C) or chosen (350 degrees C) for the conventional investments provided zero or negative mould expansion for the compensation of metal shrinkage. Crowns made from these investments exhibited heavy reaction with the mould, and the common cleaning method of sand blasting appeared to be essential. This cleaning process, however, was not adequate for the assessment of casting accuracy as the short sand blasting time (15 s) rapidly altered the fit of the crowns. The metal reacted little with the new investment and the best compensation (0.15 mm discrepancy) for the metal shrinkage, as assessed 'as cast', was achieved when the investment was heated to 950 degrees C and then cooled to the recommended mould temperature (600 degrees C).

The effect of high-power ultrasound and gas phase plasma treatment on Aspergillus spp. and Penicillium spp. count in pure culture.

PubMed

Herceg, Z; Režek Jambrak, A; Vukušić, T; Stulić, V; Stanzer, D; Milošević, S

2015-01-01

The aim of this study was to investigate and compare two nonthermal techniques in the inactivation of moulds. High power ultrasound (20 kHz) and nonthermal gas phase plasma treatments were studied in the inactivation of selected moulds. Aspergillus spp. and Penicillium spp. were chosen as the most common mould present in or on food. Experimental design was introduced to establish and optimize working variables. For high power ultrasound, the greatest reduction of moulds (indicated by the total removal of viable cells) was obtained after ultrasound treatments at 60°C (thermosonication) for 6 and 9 min (power applied, 20-39 W). For plasma treatment, the greatest inactivation of moulds was observed for the longest treatment time (5 min) and lowest sample volume (2 ml), (AP12, AP13, PP12 and PP13). The great amount of applied energy required for achieving a partial log reduction in viable cells is the limiting factor for using high-power ultrasound. However, both treatment methods could be combined in the future to produce beneficial outcomes. This study deals with nonthermal food processing techniques and the results and findings present in this study are the root for further prospective studies. The food industry is looking for nonthermal methods that will enable food preservation, reduce deterioration of food compounds and structure and prolong food shelf life. © 2014 The Society for Applied Microbiology.

Characterization of agar/soy protein biocomposite films: Effect of agar on the extruded pellets and compression moulded films.

PubMed

Garrido, T; Etxabide, A; Guerrero, P; de la Caba, K

2016-10-20

Agar/soy protein biocomposite films were successfully processed by extrusion and compression moulding, obtaining transparent and homogeneous films. The conformational changes occurred during the extrusion process and the effect of agar on the final properties were analyzed. As shown by differential scanning calorimetry (DSC) and specific mechanical energy (SME) values, during the extrusion process protein denatured and unfolded protein chains could interact with agar. These interactions were analyzed by Fourier transform infrared spectroscopy (FTIR) and the secondary structure was determined from the amide I band. Those interactions were supported by the decrease of film solubility. Furthermore, the good compatibility between agar and soy protein was confirmed by the images from scanning electron microscopy (SEM). Copyright © 2016 Elsevier Ltd. All rights reserved.

Microembossing of ultrafine grained Al: microstructural analysis and finite element modelling

NASA Astrophysics Data System (ADS)

Qiao, Xiao Guang; Bah, Mamadou T.; Zhang, Jiuwen; Gao, Nong; Moktadir, Zakaria; Kraft, Michael; Starink, Marco J.

2010-10-01

Ultra-fine-grained (UFG) Al-1050 processed by equal channel angular pressing and UFG Al-Mg-Cu-Mn processed by high-pressure torsion (HPT) were embossed at both room temperature and 300 °C, with the aim of producing micro-channels. The behaviour of Al alloys during the embossing process was analysed using finite element modelling. The cold embossing of both Al alloys is characterized by a partial pattern transfer, a large embossing force, channels with oblique sidewalls and a large failure rate of the mould. The hot embossing is characterized by straight channel sidewalls, fully transferred patterns and reduced loads which decrease the failure rate of the mould. Hot embossing of UFG Al-Mg-Cu-Mn produced by HPT shows a potential of fabrication of microelectromechanical system components with micro channels.

Identifying the Optimal Water-Occluding Earplugs: A Scientific Simulation Study.

PubMed

Kovoor, Joshua; Al Hussaini, Ali; Backhouse, Steven

2016-12-01

Numerous types of water-occluding earplugs are available as a means of preventing infection in patients with external and middle ear disease. However, little is known about the comparative efficacies of these earplugs with prolonged water exposure. In this study, we assessed the water impermeability of various earplug materials to prolonged water exposure. Nine earplugs were tested: cotton wool mixed with petroleum jelly, cotton wool externally coated with petroleum jelly, Blu-Tack, foam earplugs, silicone putty, silicone earplugs, flanged earplugs, and hard and soft silicone custom-moulds. Precision-engineered cups were filled with 30 mL water and sealed with lids that contained a 10 mm diameter hole to simulate the ear canal. The aperture was occluded with different earplugs, and the cup was inverted. Computer software was used to record the water loss to the nearest 10 milligrams 720 times over a three-hour period. The test was repeated five times for each material. The water permeability onset, rate, and total amount of water loss varied markedly between the materials; cotton wool mixed with petroleum jelly demonstrated the fastest onset of leak and the highest rate of water loss (p < 0.00001), as well as the largest amount of cumulative water loss (p = 0.00213). The soft silicone custom-mould plugs, hard silicone custom-mould plugs, foam plugs, and silicone putty demonstrated no leaks. This study demonstrates a wide range of water permeabilities of commonly used ear-occluding materials during prolonged water exposure. We found that the generally suggested regimen of cotton wool mixed with petroleum jelly may be inefficacious for substantial periods of water exposure.

Nondestructive Detection of the Internalquality of Apple Using X-Ray and Machine Vision

NASA Astrophysics Data System (ADS)

Yang, Fuzeng; Yang, Liangliang; Yang, Qing; Kang, Likui

The internal quality of apple is impossible to be detected by eyes in the procedure of sorting, which could reduce the apple’s quality reaching market. This paper illustrates an instrument using X-ray and machine vision. The following steps were introduced to process the X-ray image in order to determine the mould core apple. Firstly, lifting wavelet transform was used to get a low frequency image and three high frequency images. Secondly, we enhanced the low frequency image through image’s histogram equalization. Then, the edge of each apple's image was detected using canny operator. Finally, a threshold was set to clarify mould core and normal apple according to the different length of the apple core’s diameter. The experimental results show that this method could on-line detect the mould core apple with less time consuming, less than 0.03 seconds per apple, and the accuracy could reach 92%.

Warpage analysis on thin shell part using response surface methodology (RSM)

NASA Astrophysics Data System (ADS)

Zulhasif, Z.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Hazwan, M. H. M.

2017-09-01

The optimisation of moulding parameters appropriate to reduce warpage defects produce using Autodesk Moldflow Insight (AMI) 2012 software The product is injected by using Acrylonitrile-Butadiene-Styrene (ABS) materials. This analysis has processing parameter that varies in melting temperature, mould temperature, packing pressure and packing time. Design of Experiments (DOE) has been integrated to obtain a polynomial model using Response Surface Methodology (RSM). The Glowworm Swarm Optimisation (GSO) method is used to predict a best combination parameters to minimise warpage defect in order to produce high quality parts.

Determination of the overall migration from silicone baking moulds into simulants and food using 1H-NMR techniques.

PubMed

Helling, Ruediger; Mieth, Anja; Altmann, Stefan; Simat, Thomas Joachim

2009-03-01

Different silicone baking moulds (37 samples) were characterized with respect to potential migrating substances using 1H-NMR, RP-HPLC-UV/ELSD and GC techniques. In all cases cyclic organosiloxane oligomers with the formula [Si(CH3)2-O]n were identified (n = 6 ... 50). Additionally, linear, partly hydroxyl-terminated organosiloxanes HO-[Si(CH3)2-O]n-H (n = 7 ... 20) were found in 13 samples. No substances other than siloxanes could be detected, meaning the migrants mainly consist of organopolysiloxanes. Based on this knowledge, a 1H-NMR quantification method for siloxanes was established for the analysis of both simulants and foodstuffs. Validation of the 1H-NMR method gave suitable performance characteristics: limit of detection 8.7 mg kg(-1) oil, coefficient of variation 7.8% (at a level of 1.0 mg kg(-1) food). Migration studies were carried out with simulants (olive oil, isooctane, ethanol (95%), Tenax) as well as preparation of different cakes. From the 1st to 10th experiment, siloxane migration into cakes only slightly decreased, with a significant dependence on fat content. Migration never exceeded a level of 21 mg kg(-1) (3 mg dm(-2)) and was, therefore, well below the overall migration limit of 60 mg kg(-1) (10 mg dm(-2)). However, migration behaviour into simulants differed completely from these results.

Rapid Processing of Net-Shape Thermoplastic Planar-Random Composite Preforms

NASA Astrophysics Data System (ADS)

Jespersen, S. T.; Baudry, F.; Schmäh, D.; Wakeman, M. D.; Michaud, V.; Blanchard, P.; Norris, R. E.; Månson, J.-A. E.

2009-02-01

A novel thermoplastic composite preforming and moulding process is investigated to target cost issues in textile composite processing associated with trim waste, and the limited mechanical properties of current bulk flow-moulding composites. The thermoplastic programmable powdered preforming process (TP-P4) uses commingled glass and polypropylene yarns, which are cut to length before air assisted deposition onto a vacuum screen, enabling local preform areal weight tailoring. The as-placed fibres are heat-set for improved handling before an optional preconsolidation stage. The preforms are then preheated and press formed to obtain the final part. The process stages are examined to optimize part quality and throughput versus processing parameters. A viable processing route is proposed with typical cycle times below 40 s (for a plate 0.5 × 0.5 m2, weighing 2 kg), enabling high production capacity from one line. The mechanical performance is shown to surpass that of 40 wt.% GMT and has properties equivalent to those of 40 wt.% GMTex at both 20°C and 80°C.

Integral blow moulding for cycle time reduction of CFR-TP aluminium contour joint processing

NASA Astrophysics Data System (ADS)

Barfuss, Daniel; Würfel, Veit; Grützner, Raik; Gude, Maik; Müller, Roland

2018-05-01

Integral blow moulding (IBM) as a joining technology of carbon fibre reinforced thermoplastic (CFR-TP) hollow profiles with metallic load introduction elements enables significant cycle time reduction by shortening of the process chain. As the composite part is joined to the metallic part during its consolidation process subsequent joining steps are omitted. In combination with a multi-scale structured load introduction element its form closure function enables to pass very high loads and is capable to achieve high degrees of material utilization. This paper first shows the process set-up utilizing thermoplastic tape braided preforms and two-staged press and internal hydro formed load introduction elements. Second focuses on heating technologies and process optimization. Aiming at cycle time reduction convection and induction heating in regard to the resulting product quality is inspected by photo micrographs and computer tomographic scans. Concluding remarks give final recommendations for the process design in regard to the structural design.

Analysis of computer-aided techniques for virtual planning in nasoalveolar moulding.

PubMed

Loeffelbein, D J; Ritschl, L M; Rau, A; Wolff, K-D; Barbarino, M; Pfeifer, S; Schönberger, M; Wintermantel, E

2015-05-01

We compared two methods of planning virtual alveolar moulding as the first step in nasoalveolar moulding to provide the basis for an automated process to fabricate nasoalveolar moulding appliances by using computer-assisted design and computer-aided manufacturing (CAD/CAM). First, the initial intraoral casts taken from seven newborn babies with complete unilateral cleft lip and palate were digitised. This was repeated for the target models after conventional nasoalveolar moulding had been completed. The initial digital model for each patient was then virtually modified by two different modelling techniques to achieve the corresponding target model: parametric and freeform modelling with the software Geomagic(®). The digitally-remodelled casts were quantitatively compared with the actual target model for each patient, and the comparison between the two modified models and the target model showed that freeform modelling of the initial cast was successful (mean (SD) deviation n=7, +0.723 (0.148) to -0.694 (0.157)mm) but needed continuous orientation and was difficult to automate. The results from the parametric modelling (mean (SD) deviation, n=7, +1.168 (0.185) to -1.067 (0.221)mm) were not as good as those from freeform modelling. During parametric modelling, we found some irregularities on the surface, and transverse growth of the maxilla was not accounted for. However, this method seems to be the right one as far as automation is concerned. In addition, an external algorithm must be implemented because the function of the commercial software is limited. Copyright © 2015 The British Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

Influence of a Reclaimed Sand Addition to Moulding Sand with Furan Resin on Its Impact on the Environment.

PubMed

Holtzer, Mariusz; Dańko, Rafał; Kmita, Angelika

Metalcasting involves having a molten metal poured in a hollow mould to produce metal objects. These moulds are generally made of sand and are chemically bonded, clay-bonded, or even unbounded. There are many binder systems used. Binders based on furfuryl resins constitute currently the highest fraction in the binders no-bake group. Moulding sand, after knocking out the cast, is partially reclaimed, and the remaining part, known as waste foundry sand is used or stored outside the foundry. In this case, the environment hazardous organic compounds and metals can be leached from the moulding sand, thus causing pollution of water and soil. Also during the casting moulds with molten metal, they emit pyrolysis gases containing many different compounds, often dangerous from the BTEX and PAH group, which has adverse impacts on the environment and workers. The article presents the results of research on the impact of the regenerate addition to the moulding sand matrix on emitted gases and the degree of threat to the environment due to leaching of hazardous components. Therefore, for the total assessment of the moulding sands harmfulness, it is necessary to perform investigations concerning the dangerous substances elution into the environment during their management and storage, as well as investigations concerning emissions of hazardous substances (especially from the BTEX and PAHs group) during moulds pouring, cooling, and casting knocking out. Both kinds of investigations indicated that reclaimed sand additions to moulding sands have significantly negative influence on the environment and working conditions.

Digital prototyping technique applied for redesigning plastic products

NASA Astrophysics Data System (ADS)

Pop, A.; Andrei, A.

2015-11-01

After products are on the market for some time, they often need to be redesigned to meet new market requirements. New products are generally derived from similar but outdated products. Redesigning a product is an important part of the production and development process. The purpose of this paper is to show that using modern technology, like Digital Prototyping in industry is an effective way to produce new products. This paper tries to demonstrate and highlight the effectiveness of the concept of Digital Prototyping, both to reduce the design time of a new product, but also the costs required for implementing this step. The results of this paper show that using Digital Prototyping techniques in designing a new product from an existing one available on the market mould offers a significantly manufacturing time and cost reduction. The ability to simulate and test a new product with modern CAD-CAM programs in all aspects of production (designing of the 3D model, simulation of the structural resistance, analysis of the injection process and beautification) offers a helpful tool for engineers. The whole process can be realised by one skilled engineer very fast and effective.

Optimisation of process parameters on thin shell part using response surface methodology (RSM)

NASA Astrophysics Data System (ADS)

Faiz, J. M.; Shayfull, Z.; Nasir, S. M.; Fathullah, M.; Rashidi, M. M.

2017-09-01

This study is carried out to focus on optimisation of process parameters by simulation using Autodesk Moldflow Insight (AMI) software. The process parameters are taken as the input in order to analyse the warpage value which is the output in this study. There are some significant parameters that have been used which are melt temperature, mould temperature, packing pressure, and cooling time. A plastic part made of Polypropylene (PP) has been selected as the study part. Optimisation of process parameters is applied in Design Expert software with the aim to minimise the obtained warpage value. Response Surface Methodology (RSM) has been applied in this study together with Analysis of Variance (ANOVA) in order to investigate the interactions between parameters that are significant to the warpage value. Thus, the optimised warpage value can be obtained using the model designed using RSM due to its minimum error value. This study comes out with the warpage value improved by using RSM.

Mechanical properties of palm oil based bio-polyurethane foam of free rise and various densities

NASA Astrophysics Data System (ADS)

Hilmi, Hazmi; Zainuddin, Firuz; Cheng, Teoh Siew; Lan, Du Ngoc Uy

2017-12-01

Bio-foam was produced from palm oil-based polyol (POBP) and methylene diphenyl diisocyanate (MDI) with weight ratio of 1:1. The effect of opened mould (as free rise) and closed mould (control expansion) was investigated. Different densities of bio-polyurethane foam (0.3, 0.4 and 0.5 g.cm-3) were prepared using the closed mould system. The effect of density on morphology and compressive properties of bio-foam was studied. Results showed that bio-foam prepared by closed mould method possessed homogeneous cell structure and cell size compared to bio-foam prepared by opened mould. In addition, bio-foam using closed mould system had higher compression strength (0.47 MPa) than that of bio-foam using opened mould system (0.13 MPa). With higher density and lesser porosity, the compressive modulus and compressive strength of bio foams will be higher. The increase in compressive properties is due to the decrease in the cells size, more homogeneous cell structure and reduction in porosity content.

"Estudio tribologico de aceros para moldes. Aplicacion al moldeo por inyeccion de polibutilentereftalato reforzado con fibra de vidrio"

NASA Astrophysics Data System (ADS)

Martinez Mateo, Isidoro Jose

Mould materials for injection moulding of polymers and polymer-matrix composites represent a relevant industrial economic sector due to the large quantity of pieces and components processed. The material selection for mould manufacturing, its composition and heat treatment, the hardening procedures and machining and finishing processes determine the service performance and life of the mould. In the first part of the present study, the relationship between the hardness and microstructure and the wear resistance of mould steels from large blocks has been studied by pin-on-disc tests, studying the main wear mechanisms. In order to determine the surface damage on mould steels under real injection conditions, different commercial steels have been studied by measuring the variation of surface roughness with the number of injected pieces with different reinforcement percentages and different mould geometries, by using optical profilometry and scanning electron microscopy techniques. It was important to determine the variation of surface roughness of the moulded pieces with the number of injection operations. The materials used were polybutyleneterephthalate pure and reinforced with either 20% or 50% glass fibre. For the different mould designs, the evolution of the glass fibre orientation with injection flow has been determined by image analysis and related to roughness changes and surface damage, both of the composite parts and of the mould steel surface. Finally, the abrasion resistance of the composite parts has been studied by scratch tests as a function of the number of injected parts and of the scratch direction with respect to injection flow and glass fibre orientation. Los materiales para moldes de inyeccion de polimeros y materiales compuestos representan un sector economicamente muy relevante debido al gran aumento del numero de componentes fabricados a partir de materiales polimericos obtenidos mediante moldeo por inyeccion. La seleccion del material para la fabricacion del molde, tienen una gran influencia sobre su comportamiento en servicio a lo largo de la vida util del molde. En la primera parte del presente estudio, a partir de ensayos punzon sobre disco, se ha determinado la relacion entre la resistencia al desgaste y la dureza de aceros para moldes obtenidos a partir de bloques de gran espesor, estudiando los principales mecanismos de desgaste que tienen lugar. A continuacion, con el fin de determinar el dano superficial que sufren los aceros para moldes en condiciones reales de inyeccion, se han estudiado distintos tipos de aceros utilizados comercialmente en moldes de inyeccion de polimeros y materiales compuestos, seleccionando las condiciones de operacion para determinar la variacion de la rugosidad superficial del acero en funcion del material inyectado, del numero de operaciones sucesivas de inyeccion y de la orientacion del flujo de inyeccion, mediante tecnicas de perfilometria optica y microscopia electronica de barrido. Ademas del dano superficial sufrido por el acero con el numero de piezas inyectadas, tambien se ha determinado la evolucion de la rugosidad superficial de los materiales inyectados, polibutilentereftalato (PBT) puro y materiales compuestos derivados de PBT por adicion de un 20 o un 50% en peso de fibra de vidrio. En el caso de las piezas inyectadas, se ha caracterizado su microestructura en funcion del flujo de inyeccion y de la densidad de fibra, se han determinado sus propiedades termicas y dinamico-mecanicas, asi como la variacion de la rugosidad superficial de las piezas inyectadas con el numero de operaciones de inyeccion y con la geometria de las distintas secciones de las piezas. Finalmente, se ha evaluado la resistencia a la abrasion de PBT reforzado con un 50% de fibra, en funcion del numero de piezas inyectadas y de la direccion de rayado con respecto a la orientacion del flujo de inyeccion.

Surface topography study of prepared 3D printed moulds via 3D printer for silicone elastomer based nasal prosthesis

NASA Astrophysics Data System (ADS)

Abdullah, Abdul Manaf; Din, Tengku Noor Daimah Tengku; Mohamad, Dasmawati; Rahim, Tuan Noraihan Azila Tuan; Akil, Hazizan Md; Rajion, Zainul Ahmad

2016-12-01

Conventional prosthesis fabrication is highly depends on the hand creativity of laboratory technologist. The development in 3D printing technology offers a great help in fabricating affordable and fast yet esthetically acceptable prostheses. This study was conducted to discover the potential of 3D printed moulds for indirect silicone elastomer based nasal prosthesis fabrication. Moulds were designed using computer aided design (CAD) software (Solidworks, USA) and converted into the standard tessellation language (STL) file. Three moulds with layer thickness of 0.1, 0.2 and 0.3mm were printed utilizing polymer filament based 3D printer (Makerbot Replicator 2X, Makerbot, USA). Another one mould was printed utilizing liquid resin based 3D printer (Objet 30 Scholar, Stratasys, USA) as control. The printed moulds were then used to fabricate maxillofacial silicone specimens (n=10)/mould. Surface profilometer (Surfcom Flex, Accretech, Japan), digital microscope (KH77000, Hirox, USA) and scanning electron microscope (Quanta FEG 450, Fei, USA) were used to measure the surface roughness as well as the topological properties of fabricated silicone. Statistical analysis of One-Way ANOVA was employed to compare the surface roughness of the fabricated silicone elastomer. Result obtained demonstrated significant differences in surface roughness of the fabricated silicone (p<0.01). Further post hoc analysis also revealed significant differences in silicone fabricated using different 3D printed moulds (p<0.01). A 3D printed mould was successfully prepared and characterized. With surface topography that could be enhanced, inexpensive and rapid mould fabrication techniques, polymer filament based 3D printer is potential for indirect silicone elastomer based nasal prosthesis fabrication.

Quality evaluation of processed clay soil samples.

PubMed

Steiner-Asiedu, Matilda; Harrison, Obed Akwaa; Vuvor, Frederick; Tano-Debrah, Kwaku

2016-01-01

This study assessed the microbial quality of clay samples sold on two of the major Ghanaian markets. The study was a cross-sectional assessing the evaluation of processed clay and effects it has on the nutrition of the consumers in the political capital town of Ghana. The items for the examination was processed clay soil samples. Staphylococcus spp and fecal coliforms including Klebsiella, Escherichia, and Shigella and Enterobacterspp were isolated from the clay samples. Samples from the Kaneshie market in Accra recorded the highest total viable counts 6.5 Log cfu/g and Staphylococcal count 5.8 Log cfu/g. For fecal coliforms, Madina market samples had the highest count 6.5 Log cfu/g and also recorded the highest levels of yeast and mould. For Koforidua, total viable count was highest in the samples from the Zongo market 6.3 Log cfu/g. Central market samples had the highest count of fecal coliforms 4.6 Log cfu/g and yeasts and moulds 6.5 Log cfu/g. "Small" market recorded the highest staphylococcal count 6.2 Log cfu/g. The water activity of the clay samples were low, and ranged between 0.65±0.01 and 0.66±0.00 for samples collected from Koforidua and Accra respectively. The clay samples were found to contain Klebsiella spp. Escherichia, Enterobacter, Shigella spp. staphylococcus spp., yeast and mould. These have health implications when consumed.

Application of HS-SPME-GC-MS method for the detection of active moulds on historical parchment.

PubMed

Sawoszczuk, Tomasz; Syguła-Cholewińska, Justyna; Del Hoyo-Meléndez, Julio M

2017-03-01

The goal of this work was to analyse the profile of microbial volatile organic compounds (MVOCs) emitted by moulds growing on parchment samples, in search of particular volatiles mentioned in the literature as indicators of active mould growth. First, the growth of various moulds on samples of parchment was assessed. Those species that showed collagenolytic activity were then inoculated on two types of media: samples of parchment placed on media and on media containing amino acids that are elements of the structure of collagen. All samples were prepared inside 20-ml vials (closed system). In the first case, the media did not contain any sources of organic carbon, nitrogen, or sulphur, i.e. parchment was the only nutrient for the moulds. A third type of sample was historical parchment prepared in a Petri dish without a medium and inoculated with a collagenolytically active mould (open system). The MVOCs emitted by moulds were sampled with the headspace-SPME method. Volatiles extracted on DVB/CAR/PDMS fibres were analysed in a gas chromatography-mass spectrometry system. Qualitative and quantitative analyses of chromatograms were carried out in search of indicators of metabolic activity. The results showed that there are three groups of volatiles that can be used for the detection of active forms of moulds on parchment objects. To the best of our knowledge, this is the first work to measure MVOCs emitted by moulds growing on parchment.

Tailoring the heat transfer on the injection moulding cavity by plasma sprayed ceramic coatings

NASA Astrophysics Data System (ADS)

Bobzin, K.; Hopmann, Ch; Öte, M.; Knoch, M. A.; Alkhasli, I.; Dornebusch, H.; Schmitz, M.

2017-03-01

Inhomogeneous material shrinkage in injection moulding can cause warpage in thermoplastic components. To minimise the deformations of the injection moulding parts, the heat transfer during the cooling phase can be adjusted according to the local cooling demand on the surface of the mould cavity by means of plasma sprayed coatings with locally variable thermal resistance over the surface of the mould. Thermal resistance is a function of thermal conductivity and thickness of the coatings, where thermal conductivity of thermal barrier coatings can be adjusted by altering the chemical composition and the microstructure, which is depending on the thickness. This work evaluates the application of plasma sprayed coatings with variable thickness as thermal barrier coatings in the mould cavity. The thermal resistance of the coating and thereby the heat transfer from the melt into the mould will be influenced locally by varying the coating thickness over the cavity area according to the local cooling demand. Using the laser flash method, the thermal conduction of coatings with different thicknesses will be determined. On the basis of the experimentally determined thermal conduction, the effect of the coatings on the temperature field of the mould cavity will be numerically calculated and the required thickness distribution of the coating for an optimal temperature gradient will be determined.

Effect of Lamina Thickness of Prepreg on the Surface Accuracy of Carbon Fiber Composite Space Mirrors

NASA Astrophysics Data System (ADS)

Yang, Zhiyong; Tang, Zhanwen; Xie, Yongjie; Shi, Hanqiao; Zhang, Boming; Guo, Hongjun

2018-02-01

Composite space mirror can completely replicate the high-precision surface of mould by replication process, but the actual surface accuracy of the replication composite mirror always decreases. Lamina thickness of prepreg affects the layers and layup sequence of composite space mirror, and which would affect surface accuracy of space mirror. In our research, two groups of contrasting cases through finite element analyses (FEA) and comparative experiments were studied; the effect of different lamina thicknesses of prepreg and corresponding lay-up sequences was focused as well. We describe a special analysis model, validated process and result analysis. The simulated and measured surface figures both get the same conclusion. Reducing lamina thickness of prepreg used in replicating composite space mirror is propitious to optimal design of layup sequence for fabricating composite mirror, and could improve its surface accuracy.

Moulding techniques in lipstick manufacture: a comparative evaluation.

PubMed

Dweck, A C; Burnham, C A

1980-06-01

Synopsis This paper examines two methods of lipstick bulk manufacture: one via a direct method and the other via stock concentrates. The paper continues with a comparison of two manufactured bulks moulded in three different ways - first by split moulding, secondly by Rotamoulding, and finally by Ejectoret moulding. Full consideration is paid to time, labour and cost standards of each approach and the resultant moulding examined using some novel physical testing methods. The results of these tests are statistically analysed. Finally, on the basis of the gathered data and photomicrographical work a theoretical lipstick structure is proposed by which the results may be explained.

Ink-jet printing technology enables self-aligned mould patterning for electroplating in a single step

NASA Astrophysics Data System (ADS)

Meissner, M. V.; Spengler, N.; Mager, D.; Wang, N.; Kiss, S. Z.; Höfflin, J.; While, P. T.; Korvink, J. G.

2015-06-01

We present a new self-aligned, mask-free micro-fabrication method with which to form thick-layered conductive metal micro-structures inside electroplating moulds. Seed layer patterning for electroplating was performed by ink-jet printing using a silver nano-particle ink deposited on SU-8 or Ordyl SY permanent resist. The silver ink contact angle on SU-8 was adjusted by oxygen plasma followed by a hard bake. Besides functioning as a seed layer, the printed structures further served as a shadow mask during patterning of electroplating moulds into negative photoresist. The printed silver tracks remained in strong adhesion to the substrate when exposed to the acidic chemistry of the electroplating bath. To demonstrate the process, we manufactured rectangular, low-resistivity planar micro-coils for use in magnetic resonance microscopy. MRI images of a spring onion with an in-plane resolution down to 10 µm × 10 µm were acquired using a micro-coil on an 11.7 T MRI scanner.

Investigating the effects of laser beams (532 and 660 nm) in annihilation of pistachio mould fungus using spectrophotometry analysis

NASA Astrophysics Data System (ADS)

Saghafi, S.; Penjweini, R.; Becker, K.; Kratky, K. W.; Dodt, H.-U.

2010-09-01

When moulds are illuminated by visible electromagnetic-EM radiations, several effects on nucleus materials and nucleotides can be detected. These effects have a significant influence on mould generation or destruction. This paper presents the effects and implications of a red diode laser beam (660 nm), a second-harmonics of a Nd:YAG laser emitting green beam (532 nm), or the combination of both, on the eradication of Pistachio mould fungus. Incident doses (ID) of both beams are kept identical throughout the experiment. The absorption spectrums of irradiated mouldy samples and the bright-greenish-yellow-fluorescence (BGYF) of fungus occurring in mould texture due to electronic excitation are investigated. We found that a combination of a green and a red laser beam with an ID of 0.5 J/cm2 provides the optimal effects on Pistachio mould fungus eradication.

Yeasts and moulds contaminants of food ice cubes and their survival in different drinks.

PubMed

Francesca, N; Gaglio, R; Stucchi, C; De Martino, S; Moschetti, G; Settanni, L

2018-01-01

To evaluate the levels of unicellular and filamentous fungi in ice cubes produced at different levels and to determine their survival in alcoholic beverages and soft drinks. Sixty samples of ice cubes collected from home level (HL) productions, bars and pubs (BP) and industrial manufacturing plants (MP) were investigated for the presence and cell density of yeasts and moulds. Moulds were detected in almost all samples, while yeasts developed from the majority of HL and MP samples. Representative colonies of microfungi were subjected to phenotypic and genotypic characterization. The identification was carried out by restriction fragment length polymorphism (RFLP) analysis of the region spanning the internal transcribed spacers (ITS1 and ITS2) and the 5·8S rRNA gene. The process of yeast identification was concluded by sequencing the D1/D2 region of the 26S rRNA gene. The fungal biodiversity associated with food ice was represented by nine yeast and nine mould species. Strains belonging to Candida parapsilosis and Cryptococcus curvatus, both opportunistic human pathogens, and Penicillium glabrum, an ubiquitous mould in the ice samples analysed, were selected to evaluate the effectiveness of the ice cubes to transfer pathogenic microfungi to consumers, after addition to alcoholic beverages and soft drinks. All strains retained their viability. The survival test indicated that the most common mode of consumption of ice cubes, through its direct addition to drinks and beverages, did not reduce the viability of microfungi. This study evidenced the presence of microfungi in food ice and ascertained their survival in soft drinks and alcoholic beverages. © 2017 The Society for Applied Microbiology.

Manuscript title: antifungal proteins from moulds: analytical tools and potential application to dry-ripened foods.

PubMed

Delgado, Josué; Owens, Rebecca A; Doyle, Sean; Asensio, Miguel A; Núñez, Félix

2016-08-01

Moulds growing on the surface of dry-ripened foods contribute to their sensory qualities, but some of them are able to produce mycotoxins that pose a hazard to consumers. Small cysteine-rich antifungal proteins (AFPs) from moulds are highly stable to pH and proteolysis and exhibit a broad inhibition spectrum against filamentous fungi, providing new chances to control hazardous moulds in fermented foods. The analytical tools for characterizing the cellular targets and affected pathways are reviewed. Strategies currently employed to study these mechanisms of action include 'omics' approaches that have come to the forefront in recent years, developing in tandem with genome sequencing of relevant organisms. These techniques contribute to a better understanding of the response of moulds against AFPs, allowing the design of complementary strategies to maximize or overcome the limitations of using AFPs on foods. AFPs alter chitin biosynthesis, and some fungi react inducing cell wall integrity (CWI) pathway. However, moulds able to increase chitin content at the cell wall by increasing proteins in either CWI or calmodulin-calcineurin signalling pathways will resist AFPs. Similarly, AFPs increase the intracellular levels of reactive oxygen species (ROS), and moulds increasing G-protein complex β subunit CpcB and/or enzymes to efficiently produce glutathione may evade apoptosis. Unknown aspects that need to be addressed include the interaction with mycotoxin production by less sensitive toxigenic moulds. However, significant steps have been taken to encourage the use of AFPs in intermediate-moisture foods, particularly for mould-ripened cheese and meat products.

Development of the Mathematical Model for Ingot Quality Forecasting with Consideration of Thermal and Physical Characteristics of Mould Powder

NASA Astrophysics Data System (ADS)

Anisimov, K. N.; Loginov, A. M.; Gusev, M. P.; Zarubin, S. V.; Nikonov, S. V.; Krasnov, A. V.

2017-12-01

This paper presents the results of physical modelling of the mould powder skull in the gap between an ingot and the mould. Based on the results obtained from this and previous works, the mathematical model of mould powder behaviour in the gap and its influence on formation of surface defects was developed. The results of modelling satisfactorily conform to the industrial data on ingot surface defects.

High diversity of non-sporulating moulds in respiratory specimens of immunocompromised patients: should all the species be reported when diagnosing invasive aspergillosis?

PubMed

Garcia-Hermoso, Dea; Alanio, Alexandre; Cabaret, Odile; Olivi, Martine; Foulet, Françoise; Cordonnier, Catherine; Costa, Jean-Marc; Bretagne, Stéphane

2015-09-01

Non-sporulating moulds (NSMs) isolated from respiratory specimens are usually discarded without further testing although they may have pathogenic effects in immunocompromised patients. The objective of this study was to determine the identity and frequency of NSMs in patients with haematological malignancies. We analysed the mycological results of 251 consecutive respiratory samples from 104 haematology patients. Yeast and sporulating moulds were identified at the genus/species level according to their phenotypic features. NSMs were identified by internal transcribed spacer (ITS) sequencing. We detected 179 positive samples, of which 10.1% (18/179) were mixtures of moulds and 26.3% (47/179) were mixtures of moulds and yeast. We identified 142 moulds belonging to 11 different genera/species or groups, with Aspergillus fumigatus (n = 50), Penicillium spp. (n = 31) and NSM (n = 24) being the most frequently isolated species. Twenty-two NSMs were successfully sequenced: 18 were basidiomycetes and six were ascomycetes, corresponding to 16 different genera/species. NSMs were isolated with A. fumigatus in the same sample or in a subsequent sample in five patients with probable invasive aspergillosis. The conclusion is that the respiratory specimens of immunocompromised patients frequently contain very diverse mould species that may increase the virulence of pathogenic species. Reporting all mould species isolated when diagnosing invasive fungal infection could test this hypothesis. © 2015 Blackwell Verlag GmbH.

Studies on mould growth and biomass production using waste banana peel.

PubMed

Essien, J P; Akpan, E J; Essien, E P

2005-09-01

Hyphomycetous (Aspergillus fumigatus) and Phycomycetous (Mucor hiemalis) moulds were cultivated in vitro at room temperature (28 + 20 degrees C) to examined their growth and biomass production on waste banana peel agar (BPA) and broth (BPB) using commercial malt extract agar (MEA) and broth (MEB) as control. The moulds grew comparatively well on banana peel substrates. No significant difference (p > 0.05) in radial growth rates was observed between moulds cultivated on PBA and MEA, although growth rates on MEA were slightly better. Slight variations in sizes of asexual spores and reproductive hyphae were also observed between moulds grown on MEA and BPA. Smaller conidia and sporangiospores, and shorter aerial hyphae (conidiophores and sporangiophores) were noticed in moulds grown on BPA than on MEA. The biomass weight of the test moulds obtained after one month of incubation with BPB were only about 1.8 mg and 1.4 mg less than values recorded for A. fumigatus and M. hiemalis respectively, grown on MEB. The impressive performance of the moulds on banana peel substrate may be attributed to the rich nutrient (particularly the crude protein 7.8% and crude fat 11.6% contents) composition of banana peels. The value of this agricultural waste can therefore be increased by its use not only in the manufacture of mycological medium but also in the production of valuable microfungal biomass which is rich in protein and fatty acids.

SU-E-T-04: 3D Printed Patient-Specific Surface Mould Applicators for Brachytherapy Treatment of Superficial Lesions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cumming, I; Lasso, A; Rankin, A

2014-06-01

Purpose: Evaluate the feasibility of constructing 3D-printed patient-specific surface mould applicators for HDR brachytherapy treatment of superficial lesions. Methods: We propose using computer-aided design software to create 3D printed surface mould applicators for brachytherapy. A mould generation module was developed in the open-source 3D Slicer ( http://www.slicer.org ) medical image analysis platform. The system extracts the skin surface from CT images, and generates smooth catheter paths over the region of interest based on user-defined start and end points at a specified stand-off distance from the skin surface. The catheter paths are radially extended to create catheter channels that are sufficientlymore » wide to ensure smooth insertion of catheters for a safe source travel. An outer mould surface is generated to encompass the channels. The mould is also equipped with fiducial markers to ensure its reproducible placement. A surface mould applicator with eight parallel catheter channels of 4mm diameters was fabricated for the nose region of a head phantom; flexible plastic catheters of 2mm diameter were threaded through these channels maintaining 10mm catheter separations and a 5mm stand-off distance from the skin surface. The apparatus yielded 3mm thickness of mould material between channels and the skin. The mould design was exported as a stereolithography file to a Dimension SST1200es 3D printer and printed using ABS Plus plastic material. Results: The applicator closely matched its design and was found to be sufficiently rigid without deformation during repeated application on the head phantom. Catheters were easily threaded into channels carved along catheter paths. Further tests are required to evaluate feasibility of channel diameters smaller than 4mm. Conclusion: Construction of 3D-printed mould applicators show promise for use in patient specific brachytherapy of superficial lesions. Further evaluation of 3D printing techniques and materials is required for constructing sufficiently thin, rigid and durable surface moulds suitable for clinical deployment.« less

A review of biocompatible metal injection moulding process parameters for biomedical applications.

PubMed

Hamidi, M F F A; Harun, W S W; Samykano, M; Ghani, S A C; Ghazalli, Z; Ahmad, F; Sulong, A B

2017-09-01

Biocompatible metals have been revolutionizing the biomedical field, predominantly in human implant applications, where these metals widely used as a substitute to or as function restoration of degenerated tissues or organs. Powder metallurgy techniques, in specific the metal injection moulding (MIM) process, have been employed for the fabrication of controlled porous structures used for dental and orthopaedic surgical implants. The porous metal implant allows bony tissue ingrowth on the implant surface, thereby enhancing fixation and recovery. This paper elaborates a systematic classification of various biocompatible metals from the aspect of MIM process as used in medical industries. In this study, three biocompatible metals are reviewed-stainless steels, cobalt alloys, and titanium alloys. The applications of MIM technology in biomedicine focusing primarily on the MIM process setting parameters discussed thoroughly. This paper should be of value to investigators who are interested in state of the art of metal powder metallurgy, particularly the MIM technology for biocompatible metal implant design and development. Copyright © 2017 Elsevier B.V. All rights reserved.

Polyolefin backbone substitution in binders for low temperature powder injection moulding feedstocks.

PubMed

Hausnerova, Berenika; Kuritka, Ivo; Bleyan, Davit

2014-02-27

This paper reports the substitution of polyolefin backbone binder components with low melting temperature carnauba wax for powder injection moulding applications. The effect of various binder compositions of Al₂O₃ feedstock on thermal degradation parameters is investigated by thermogravimetric analysis. Within the experimental framework 29 original feedstock compositions were prepared and the superiority of carnauba wax over the polyethylene binder backbone was demonstrated in compositions containing polyethylene glycol as the initial opening agent and governing the proper mechanism of the degradation process. Moreover, the replacement of synthetic polymer by the natural wax contributes to an increase of environmental sustainability of modern industrial technologies.

Biolithography: Slime mould patterning of polyaniline

NASA Astrophysics Data System (ADS)

Berzina, Tatiana; Dimonte, Alice; Adamatzky, Andrew; Erokhin, Victor; Iannotta, Salvatore

2018-03-01

Slime mould Physarum polycephalum develops intricate patterns of protoplasmic networks when foraging on a non-nutrient substrates. The networks are optimised for spanning larger spaces with minimum body mass and for quick transfer of nutrients and metabolites inside the slime mould's body. We hybridise the slime mould's networks with conductive polymer polyaniline and thus produce micro-patterns of conductive networks. This unconventional lithographic method opens new perspectives in development of living technology devices, biocompatible non-silicon hardware for applications in integrated circuits, bioelectronics, and biosensing.

Materials Characterisation and Analysis for Flow Simulation of Liquid Resin Infusion

NASA Astrophysics Data System (ADS)

Sirtautas, J.; Pickett, A. K.; George, A.

2015-06-01

Liquid Resin Infusion (LRI) processes including VARI and VARTM have received increasing attention in recent years, particularly for infusion of large parts, or for low volume production. This method avoids the need for costly matched metal tooling as used in Resin Transfer Moulding (RTM) and can provide fast infusion if used in combination with flow media. Full material characterisation for LRI analysis requires models for three dimensional fabric permeability as a function of fibre volume content, fabric through-thickness compliance as a function of resin pressure, flow media permeability and resin viscosity. The characterisation of fabric relaxation during infusion is usually determined from cyclic compaction tests on saturated fabrics. This work presents an alternative method to determine the compressibility by using LRI flow simulation and fitting a model to experimental thickness measurements during LRI. The flow media is usually assumed to have isotropic permeability, but this work shows greater simulation accuracy from combining the flow media with separation plies as a combined orthotropic material. The permeability of this combined media can also be determined by fitting the model with simulation to LRI flow measurements. The constitutive models and the finite element solution were validated by simulation of the infusion of a complex aerospace demonstrator part.

The first report on mushroom green mould disease in Croatia.

PubMed

Hatvani, Lóránt; Sabolić, Petra; Kocsubé, Sándor; Kredics, László; Czifra, Dorina; Vágvölgyi, Csaba; Kaliterna, Joško; Ivić, Dario; Đermić, Edyta; Kosalec, Ivan

2012-12-01

Green mould disease, caused by Trichoderma species, is a severe problem for mushroom growers worldwide, including Croatia. Trichoderma strains were isolated from green mould-affected Agaricus bisporus (button or common mushroom) compost and Pleurotus ostreatus (oyster mushroom) substrate samples collected from Croatian mushroom farms. The causal agents of green mould disease in the oyster mushroom were T. pleurotum and T. pleuroticola, similar to other countries. At the same time, the pathogen of A. bisporus was exclusively the species T. harzianum, which is different from earlier findings and indicates that the range of mushroom pathogens is widening. The temperature profiles of the isolates and their hosts overlapped, thus no range was found that would allow optimal growth of the mushrooms without mould contamination. Ferulic acid and certain phenolic compounds, such as thymol showed remarkable fungistatic effect on the Trichoderma isolates, but inhibited the host mushrooms as well. However, commercial fungicides prochloraz and carbendazim were effective agents for pest management. This is the first report on green mould disease of cultivated mushrooms in Croatia.

Quality evaluation of processed clay soil samples

PubMed Central

Steiner-Asiedu, Matilda; Harrison, Obed Akwaa; Vuvor, Frederick; Tano-Debrah, Kwaku

2016-01-01

Introduction This study assessed the microbial quality of clay samples sold on two of the major Ghanaian markets. Methods The study was a cross-sectional assessing the evaluation of processed clay and effects it has on the nutrition of the consumers in the political capital town of Ghana. The items for the examination was processed clay soil samples. Results Staphylococcus spp and fecal coliforms including Klebsiella, Escherichia, and Shigella and Enterobacterspp were isolated from the clay samples. Samples from the Kaneshie market in Accra recorded the highest total viable counts 6.5 Log cfu/g and Staphylococcal count 5.8 Log cfu/g. For fecal coliforms, Madina market samples had the highest count 6.5 Log cfu/g and also recorded the highest levels of yeast and mould. For Koforidua, total viable count was highest in the samples from the Zongo market 6.3 Log cfu/g. Central market samples had the highest count of fecal coliforms 4.6 Log cfu/g and yeasts and moulds 6.5 Log cfu/g. “Small” market recorded the highest staphylococcal count 6.2 Log cfu/g. The water activity of the clay samples were low, and ranged between 0.65±0.01 and 0.66±0.00 for samples collected from Koforidua and Accra respectively. Conclusion The clay samples were found to contain Klebsiella spp. Escherichia, Enterobacter, Shigella spp. staphylococcus spp., yeast and mould. These have health implications when consumed. PMID:27642456

Slumping during sculpturing of composite materials.

PubMed

Chiang, Yu-Chih; Knezevic, Alena; Kunzelmann, Karl-Heinz

2008-12-01

This study investigated the slumping characteristics of four composite materials during sculpturing prior to their polymerization. Four different composite materials were used to measure shape deformation due to slumping. Silicon impressions of the occlusal plane of three different molars were used as a mould for the composite samples. The surface of the samples was digitized with a laser scanner (400 slices, lateral resolution: 25 microm). Scans were made after 1-4 min. The 3D data sets were numerically superimposed with matching software and differences were calculated relative to the baseline measurement. The amount of surface deformation increases with increasing observation time. The average coefficient of variation was 0.2. The largest mean amount of slumping was observed for ELS with tooth mould 1 (150.0 microm), and for Clearfil Majesty with tooth mould 2 (98.3 microm) and mould 3 (42.8 microm). Miris 2 Dentin and Synergy D6 Enamel were rather similar and seem to exhibit little deformation. The slump flow of ELS and Clearfil Majesty was up to 400% higher than the formers. The deformation could be sorted in the following order "mould 3"<"mould 2"<"mould 1" for all materials and all observation time. There was a significant influence (p<0.05) of the three factors, time, mould and composite type (ANOVA). This specific method provides a reproducible approach for the assessment of the handling characteristics of composite materials. The results can identify slumping differences and assist in collecting information about the feasibility of a material for certain indications.

In-mould decorating.

PubMed

Bienias, Thomas J

2002-10-01

Advances in plastics moulding technology and the use of in-mould decorating are giving medical device manufacturers an opportunity to expand the variety of their products and reduce the cost of the final product. Other industries have tested the waters and found them friendly. The medical device industry could be next.

Slime mould foraging behaviour as optically coupled logical operations

NASA Astrophysics Data System (ADS)

Mayne, R.; Adamatzky, A.

2015-04-01

Physarum polycephalum is a macroscopic plasmodial slime mould whose apparently 'intelligent' behaviour patterns may be interpreted as computation. We employ plasmodial phototactic responses to construct laboratory prototypes of NOT and NAND logical gates with electrical inputs/outputs and optical coupling in which the slime mould plays dual roles of computing device and electrical conductor. Slime mould logical gates are fault tolerant and resettable. The results presented here demonstrate the malleability and resilience of biological systems and highlight how the innate behaviour patterns of living substrates may be used to implement useful computation.

Direct transfer of learned behaviour via cell fusion in non-neural organisms

PubMed Central

Vogel, David

2016-01-01

Cell fusion is a fundamental phenomenon observed in all eukaryotes. Cells can exchange resources such as molecules or organelles during fusion. In this paper, we ask whether a cell can also transfer an adaptive response to a fusion partner. We addressed this question in the unicellular slime mould Physarum polycephalum, in which cell–cell fusion is extremely common. Slime moulds are capable of habituation, a simple form of learning, when repeatedly exposed to an innocuous repellent, despite lacking neurons and comprising only a single cell. In this paper, we present a set of experiments demonstrating that slime moulds habituated to a repellent can transfer this adaptive response by cell fusion to individuals that have never encountered the repellent. In addition, we show that a slime mould resulting from the fusion of a minority of habituated slime moulds and a majority of unhabituated ones still shows an adaptive response to the repellent. Finally, we further reveal that fusion must last a certain time to ensure an effective transfer of the behavioural adaptation between slime moulds. Our results provide strong experimental evidence that slime moulds exhibit transfer of learned behaviour during cell fusion and raise the possibility that similar phenomena may occur in other cell–cell fusion systems. PMID:28003457

A bio-inspired microstructure induced by slow injection moulding of cylindrical block copolymers.

PubMed

Stasiak, Joanna; Brubert, Jacob; Serrani, Marta; Nair, Sukumaran; de Gaetano, Francesco; Costantino, Maria Laura; Moggridge, Geoff D

2014-08-28

It is well known that block copolymers with cylindrical morphology show alignment with shear, resulting in anisotropic mechanical properties. Here we show that well-ordered bi-directional orientation can be achieved in such materials by slow injection moulding. This results in a microstructure, and anisotropic mechanical properties, similar to many natural tissues, making this method attractive for engineering prosthetic fibrous tissues. An application of particular interest to us is prosthetic polymeric heart valve leaflets, mimicking the shape, microstructure and hence performance of the native valve. Anisotropic layers have been observed for cylinder-forming block copolymers centrally injected into thin circular discs. The skin layers exhibit orientation parallel to the flow direction, whilst the core layer shows perpendicularly oriented domains; the balance of skin to core layers can be controlled by processing parameters such as temperature and injection rate. Heart valve leaflets with a similar layered structure have been prepared by injection moulding. Numerical modelling demonstrates that such complex orientation can be explained and predicted by the balance of shear and extensional flow.

Rapid tooling method for soft customized removable oral appliances.

PubMed

Salmi, Mika; Tuomi, Jukka; Sirkkanen, Rauno; Ingman, Tuula; Mäkitie, Antti

2012-01-01

Traditionally oral appliances i.e. removable orthodontic appliances, bite splints and snoring / sleep apnea appliances are made with alginate impressions and wax registrations. Our aim was to describe the process of manufacturing customized oral appliances with a new technique i.e. rapid tooling method. The appliance should ideally be custom made to match the teeth. An orthodontic patient, scheduled for conventional orthodontic treatment, served as a study subject. After a precise clinical and radiographic examination, the approach was to digitize the patient's dental arches and then to correct them virtually by computer. Additive manufacturing was then used to fabricate a mould for a soft customized appliance. The mould was manufactured using stereolithography from Somos ProtoGen O-XT 18420 material. Casting material for the mould to obtain the final appliance was silicone. As a result we managed to create a customized soft orthodontic appliance. Also, the accuracy of the method was found to be adequate. Two versions of the described device were manufactured: one with small and one with moderate orthodontic force. The study person also gave information on the subjective patient adaptation aspects of the oral appliance.

Meso-macro simulation of the woven fabric local deformation in draping

NASA Astrophysics Data System (ADS)

Iwata, Akira; Inoue, Takuya; Naouar, Naim; Boisse, Philippe; Lomov, Stepan V.

2018-05-01

The paper reports results of such combined meso-macro modelling for a plain weave carbon fabric with spread yarns. The boundary conditions for a local meso-model are taken from the macro draping simulation. The fabric geometry is modelled with WiseTex and transferred to the finite element package. A hyperelastic constitutive model for the yarns (Charmetant - Boisse) is used in the meso-modelling; the model parameters are identified and validated in independent tension, shear, compaction and bending tests of the yarn and the fabric. The simulation reproduces local yarn slippage and buckling, for example, the yarn distortion on the 3D mould corner (see the figure). The simulations are compared with the local fabric distortions observed during draping experiments.

Product Development and its Comparative Analysis by SLA, SLS and FDM Rapid Prototyping Processes

NASA Astrophysics Data System (ADS)

Choudhari, C. M.; Patil, V. D.

2016-09-01

To grab market and meeting deadlines has increased the scope of new methods in product design and development. Industries continuously strive to optimize the development cycles with high quality and cost efficient products to maintain market competitiveness. Thus the need of Rapid Prototyping Techniques (RPT) has started to play pivotal role in rapid product development cycle for complex product. Dimensional accuracy and surface finish are the corner stone of Rapid Prototyping (RP) especially if they are used for mould development. The paper deals with the development of part made with the help of Selective Laser Sintering (SLS), Stereo-lithography (SLA) and Fused Deposition Modelling (FDM) processes to benchmark and investigate on various parameters like material shrinkage rate, dimensional accuracy, time, cost and surface finish. This helps to conclude which processes can be proved to be effective and efficient in mould development. In this research work the emphasis was also given to the design stage of a product development to obtain an optimum design solution for an existing product.

Debinding and Sintering of an Injection-Moulded Hypereutectic Al⁻Si Alloy.

PubMed

Ni, Jiaqi; Yu, Muhuo; Han, Keqing

2018-05-16

Hypereutectic Al⁻Si (20 wt.%) alloy parts were fabricated by employing a powder injection moulding (PIM) technique with a developed multi-component binder system composed of high-density polyethylene (35 wt.%), carnauba wax (62 wt.%) and stearic acid (3 wt.%). The feedstocks contained 83 wt.% metal powders. The debinding process was carried out by a combination of solvent extraction and thermal decomposition. The effects of solvent debinding variables such as kind of solvents, debinding temperatures and time, and the bulk surface area to volume ratios on the debinding process were investigated. Thermal debinding and the subsequent sintering process were carried out in a heating sequence under a nitrogen atmosphere. The influences of sintering temperature and sintering time on the mechanical properties and structure were considered. Under the optimal sintering condition, sintering at 550 °C for 3 h, the final sintering parts were free of distortion and exhibited good mechanical properties. Relative sintered density, Brinell hardness, and tensile strength were ~95.5%, 58 HBW and ~154, respectively.

Development of crayfish bio-based plastic materials processed by small-scale injection moulding.

PubMed

Felix, Manuel; Romero, Alberto; Cordobes, Felipe; Guerrero, Antonio

2015-03-15

Protein has been investigated as a source for biodegradable polymeric materials. This work evaluates the development of plastic materials based on crayfish and glycerol blends, processed by injection moulding, as a fully biodegradable alternative to conventional polymer-based plastics. The effect of different additives, namely sodium sulfite or bisulfite as reducing agents, urea as denaturing agent and L-cysteine as cross-linking agent, is also analysed. The incorporation of any additive always yields an increase in energy efficiency at the mixing stage, but its effect on the mechanical properties of the bioplastics is not so clear, and even dampened. The additive developing a greater effect is L-cysteine, showing higher Young's modulus values and exhibiting a remnant thermosetting potential. Thus, processing at higher temperature yields a remarkable increase in extensibility. This work illustrates the feasibility of crayfish-based green biodegradable plastics, thereby contributing to the search for potential value-added applications for this by-product. © 2014 Society of Chemical Industry.

Colorimetric micro-assay for accelerated screening of mould inhibitors

Treesearch

Carol A. Clausen; Vina W. Yang

2013-01-01

Since current standard laboratory methods are time-consuming macro-assays that rely on subjective visual ratings of mould growth, rapid and quantitative laboratory methods are needed to screen potential mould inhibitors for use in and on cellulose-based products. A colorimetric micro-assay has been developed that uses XTT tetrazolium salt to enzymatically assess...

An improvised mould for vaginoplasty.

PubMed

Viegas, T; Thomas, R; Guido, N L

1989-07-01

The use of a simple, improvised mould for vaginoplasty is described. It is made of rubber foam rolled over a winged infusion cannula and covered over by condoms. It offers a number of advantages over conventional moulds, the main ones being its simplicity of construction and its ease of application and removal from the neo-vagina.

Fungi associated with black mould on baobab trees in southern Africa.

PubMed

Cruywagen, Elsie M; Crous, Pedro W; Roux, Jolanda; Slippers, Bernard; Wingfield, Michael J

2015-07-01

There have been numerous reports in the scientific and popular literature suggesting that African baobab (Adansonia digitata) trees are dying, with symptoms including a black mould on their bark. The aim of this study was to determine the identity of the fungi causing this black mould and to consider whether they might be affecting the health of trees. The fungi were identified by sequencing directly from mycelium on the infected tissue as well as from cultures on agar. Sequence data for the ITS region of the rDNA resulted in the identification of four fungi including Aureobasidium pullulans, Toxicocladosporium irritans and a new species of Rachicladosporium described here as Rachicladosporium africanum. A single isolate of an unknown Cladosporium sp. was also found. These fungi, referred to here as black mould, are not true sooty mould fungi and they were shown to penetrate below the bark of infected tissue, causing a distinct host reaction. Although infections can lead to dieback of small twigs on severely infected branches, the mould was not found to kill trees.

Laser cleaning of the contaminations on the surface of tire mould

NASA Astrophysics Data System (ADS)

Ye, Yayun; Jia, Baoshen; Chen, Jing; Jiang, Yilan; Tang, Hongping; Wang, Haijun; Luan, Xiaoyu; Liao, Wei; Zhang, Chuanchao; Yao, Caizhen

2017-07-01

During the manufacturing of tires, surface pollutants on tire mould will lead to the production of unqualified tires. Tire moulds need to be regularly cleaned. Laser cleaning is recognized as a non-destructive, effective, precise and environmental friendly method. In this paper, laser cleaning was used to remove contaminants on tire mould surface. First, laser induced damage experiments were performed. The results showed that the roughness and hardness of the cast steel sample surface seldom changed under the energy range of 140.1-580.2 mJ laser irradiation 1 pulse and the energy range of 44.7-168.9 mJ laser irradiation 100 pulses. In the laser cleaning experiments, the cleaning thresholds and the optimal cleaning parameters were obtained. Results indicated that laser cleaning was safe and effective for tire mould contamination removal.

Design and development of anthropometric device for the standardization of sizes of knee-ankle-foot orthoses.

PubMed

Dwivedi, M; Shetty, K D; Nath, L Narendra

2009-01-01

An anthropometric device (AD) was designed and developed to collect data on foot and knee of locomotor disabled people. The aim was to standardize the sizes of knee-ankle-foot orthoses (KAFOs) in a standard modular form so that they can be mass produced to cater for fitting to a large number of locomotor disabled people. The anthropometric data collected on large numbers of locomotor disabled people were processed, with the help of a computer programme, to arrive at standard sizes for three modules, i.e. a foot plate (seven sizes), knee pieces (six sizes) and a lateral upright in a universal size. These modules were produced by plastic injection moulding and compression moulding processes using glass-reinforced polypropylene. KAFOs were assembled and fitted to locomotor disabled people. Feedback obtained was encouraging and this vindicated the concept, design and utility of the AD.

[Classical and molecular methods for identification and quantification of domestic moulds].

PubMed

Fréalle, E; Bex, V; Reboux, G; Roussel, S; Bretagne, S

2017-12-01

To study the impact of the constant and inevitable inhalation of moulds, it is necessary to sample, identify and count the spores. Environmental sampling methods can be separated into three categories: surface sampling is easy to perform but non quantitative, air sampling is easy to calibrate but provides time limited information, and dust sampling which is more representative of long term exposure to moulds. The sampling strategy depends on the objectives (evaluation of the risk of exposure for individuals; quantification of the household contamination; evaluation of the efficacy of remediation). The mould colonies obtained in culture are identified using microscopy, Maldi-TOF, and/or DNA sequencing. Electrostatic dust collectors are an alternative to older methods for identifying and quantifying household mould spores. They are easy to use and relatively cheap. Colony counting should be progressively replaced by quantitative real-time PCR, which is already validated, while waiting for more standardised high throughput sequencing methods for assessment of mould contamination without technical bias. Despite some technical recommendations for obtaining reliable and comparable results, the huge diversity of environmental moulds, the variable quantity of spores inhaled and the association with other allergens (mites, plants) make the evaluation of their impact on human health difficult. Hence there is a need for reliable and generally applicable quantitative methods. Copyright © 2017 SPLF. Published by Elsevier Masson SAS. All rights reserved.

Application of solid-phase microextraction with gas chromatography and mass spectrometry for the early detection of active moulds on historical woollen objects.

PubMed

Sawoszczuk, Tomasz; Syguła-Cholewińska, Justyna; Del Hoyo-Meléndez, Julio M

2017-02-01

The goal of this work was to determine the microbial volatile organic compounds emitted by moulds growing on wool in search of particular volatiles mentioned in the literature as indicators of active mould growth. The keratinolytically active fungi were inoculated on two types of media: (1) samples of wool placed on broths, and (2) on broths containing amino acids that are elements of the structure of keratin. All samples were prepared inside 20 mL vials (closed system). In the first case (1) the broths did not contain any sources of organic carbon, nitrogen, or sulfur, i.e. wool was the only nutrient for the moulds. A third type of sample was historical wool prepared in a Petri dish without a broth and inoculated with a keratinolytically active mould (open system). The microbial volatiles emitted by moulds were sampled with the headspace solid-phase microextraction method. Volatiles extracted on solid-phase microextraction fibers were analyzed in a gas chromatography with mass spectrometry system. Qualitative and quantitative analyses of chromatograms were carried out in search of indicators of metabolic activity. The results showed that there are three groups of volatiles that can be used for the detection of active forms of moulds on woollen objects. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

COMPARISON OF POPULATIONS OF MOULD SPECIES IN HOMES IN THE UK AND US USING MOLD-SPECIFIC QUANTITATIVE PCR (MSQPCR)

EPA Science Inventory

The goal of this research was to compare the populations of 81 mold species in homes in USA and UK using mould specific quantitative polymerase chain reaction (MSQPCR) technology. Dust samples were obtained from randomly selected homes in Great Britain (n=11). The mould populat...

Determining the suitability of Lactobacilli antifungal metabolites for inhibiting mould growth

Treesearch

Vina W. Yang; Carol A. Clausen

2005-01-01

In recent years, public concern about indoor mould growth has increased dramatically in the United States. In this study, lactic acid bacteria (LAB), which are known to produce antimicrobial compounds important in the biopreservation of food, were evaluated to determine if the same antimicrobial properties can be used to inhibit mould fungi that typically colonize wood...

Temperature and strain registration by fibre-optic strain sensor in the polymer composite materials manufacturing

NASA Astrophysics Data System (ADS)

Matveenko, V. P.; Kosheleva, N. A.; Shardakov, I. N.; Voronkov, A. A.

2018-04-01

The presence of process-induced strains induced by various manufacturing and operational factors is one of the characteristics of polymer composite materials (PCM). Conventional methods of registration and evaluation of process-induced strains can be laborious, time-consuming and demanding in terms of technical applications. The employment of embedded fibre-optic strain sensors (FOSS) offers a real prospect of measuring residual strains. This paper demonstrates the potential for using embedded FOSS for recording technological strains in a PCM plate. The PCM plate is manufactured from prepreg, using the direct compression-moulding method. In this method, the prepared reinforcing package is placed inside a mould, heated, and then exposed to compaction pressure. The examined technology can be used for positioning FOSS between the layers of the composite material. Fibre-optic sensors, interacting with the material of the examined object, make it possible to register the evolution of the strain process during all stages of polymer-composite formation. FOSS data were recorded with interrogator ASTRO X 327. The obtained data were processed using specially developed algorithms.

Fabrication of scalable and structured tissue engineering scaffolds using water dissolvable sacrificial 3D printed moulds.

PubMed

Mohanty, Soumyaranjan; Larsen, Layla Bashir; Trifol, Jon; Szabo, Peter; Burri, Harsha Vardhan Reddy; Canali, Chiara; Dufva, Marin; Emnéus, Jenny; Wolff, Anders

2015-10-01

One of the major challenges in producing large scale engineered tissue is the lack of ability to create large highly perfused scaffolds in which cells can grow at a high cell density and viability. Here, we explore 3D printed polyvinyl alcohol (PVA) as a sacrificial mould in a polymer casting process. The PVA mould network defines the channels and is dissolved after curing the polymer casted around it. The printing parameters determined the PVA filament density in the sacrificial structure and this density resulted in different stiffness of the corresponding elastomer replica. It was possible to achieve 80% porosity corresponding to about 150 cm(2)/cm(3) surface to volume ratio. The process is easily scalable as demonstrated by fabricating a 75 cm(3) scaffold with about 16,000 interconnected channels (about 1m(2) surface area) and with a channel to channel distance of only 78 μm. To our knowledge this is the largest scaffold ever to be produced with such small feature sizes and with so many structured channels. The fabricated scaffolds were applied for in-vitro culturing of hepatocytes over a 12-day culture period. Smaller scaffolds (6×4 mm) were tested for cell culturing and could support homogeneous cell growth throughout the scaffold. Presumably, the diffusion of oxygen and nutrient throughout the channel network is rapid enough to support cell growth. In conclusion, the described process is scalable, compatible with cell culture, rapid, and inexpensive. Copyright © 2015. Published by Elsevier B.V.

Tools and methods for automated assembly of miniaturized gear systems

NASA Astrophysics Data System (ADS)

Nienhaus, Matthias; Ehrfeld, Wolfgang; Berg, Udo; Schmitz, Felix; Soultan, H.

2000-10-01

The assembly of gear systems with the size of a pin head is almost beyond the bound of human tactile skills. The magic formula for series fabrication of this hybrid micro systems is the automation of the assembly process. As a contribution, this paper presents and discusses three different assembly methods comprising specifically developed tools for different types of planetary gears with outer diameters of 1.9 mm. Because of the huge importance for the complete micro assembly process, particular attention will be dedicated to the feeding and magazining of the micro gear components. Starting with metallic gear wheels as bulk good, an extremely miniaturized gear system of the Wolfram type has been automatically assembled by employing the strategy of tolerance compensation movement. As a key component, a modular tong gripper with specifically adapted gripping jaws produced by LIGA technology has been used. Further detailed investigations were spend on handling and assembly of micro injection moulded gear wheels made of POM for a three state planetary gear system. One strategy, following the idea of in situ observation, focuses on the intensive use of electronic pattern recognition. Alternatively, an unusual method based on a novel plastic wafer magazine will be discussed in detail. Hereby the exact position and orientation of injection moulded micro components will be presented from the manufacturing process up to the final micro assembly procedure. By simplifying the moulding of the micro gears as well as their handling, storing and assembly, this method has the potential to revolutionize the series fabrication of products with dimensions in the microscopic range in general.

Slumped glass optics development with pressure assistance

NASA Astrophysics Data System (ADS)

Salmaso, B.; Basso, S.; Civitani, M.; Ghigo, M.; Hołyszko, J.; Spiga, D.; Vecchi, G.; Pareschi, G.

2016-07-01

Thin glass mirrors are a viable solution to build future X-ray telescopes with high angular resolution and large collecting area. This approach is very attractive for the optics implementation of future X-ray astronomy projects like the X-ray Surveyor Missions in USA, the XTP mission in China and the FORCE mission in Japan (all this projects could have an European participation). In the case of the X-ray Surveyor Mission, where a sub-arcsec angular resolution is requested, the use of actuators or post correction with sputtering deposition is envisaged. The hot slumping assisted by pressure is an innovative technology developed in our laboratories to replicate a mould figure. Our hot slumping process is based on thin substrates of Eagle XG glass to be thermally formed on Zerodur K20 moulds. This technology is coupled with an integration process able to damp low frequency errors. A continuous improvement in the reduction of the mid-frequency errors led to slumped glass foils with a potential angular resolution evaluated from the metrological data of a few arcsec. High frequency errors have been for a long time a critical point of our technology. In particular, the pressure assistance was leading to a partial replication of the mould micro-roughness, causing a non-negligible contribution to the Point Spread Function (PSF), in the incidence angle and X-ray energy range of operation. Therefore, we developed a new process to further reduce the micro-roughness of slumped glass foils, making now the technology attractive also for telescopes sensitive at higher X-ray energies. This paper provides the latest status of our research.

PREPARATION OF B-CYCLODEXTRIN-THIABENDAZOLE-PIPERONYL BUTOXIDE SUPRAMOLECULAR COMPLEX AND ITS ACTIVITY AGAINST BLUE AND GREEN MOULD DECAY ON INOCULATED SATSUMA FRUIT.

PubMed

Fadda, A; Schirra, M; D'Aquino, S; Migheli, Q; Borzatta, V; Delogu, G

2015-01-01

The supramolecular complex of β-cyclodextrin-thiabendazole-piperony butoxide (βCD-TBZ/PBO) was prepared and its structure was characterized by 1H NMR. Additionally, the antifungal activity of βCD-TBZ/PBO was investigated in comparison with the commercially available thiabendazole (TBZ) fungicide by in vitro tests and on artificially inoculated 'Okitsu' satsuma fruit dipped in water at 20 degrees C or at 50 degrees C to control postharvest blue (Penicillium italicum) and green mould (P. digitatum). β-CD-TBZ/PBO is stable for several months when stored as powder in a dark bottle. At pH 7.0 the water solubility of the βCD-TBZ/PBO complex was consistently higher than free TBZ. Water dip at 20 degrees C did not affect decay incidence caused by blue mould but favoured the development of green mould during 4-8 days of storage at 20 degrees C with respect to untreated (control) fruit. Water at 50 degrees C effectively reduced the incidence of blue mould and totally suppressed green mould during the first 4 days but lost its efficacy afterwards. By contrast, both TBZ and βCD-TBZ/PBO had a lasting effect and were equally effective in controlling green and blue mould decay when applied at 20 degrees C and 60 mg L(-1) active ingredient (a.i.). When applied at 50 degrees C and 20 mg L(-1) a.i. the activity of the complex against blue mould was inferior than the corresponding treatment with TBZ. In vitro assays revealed a significant effectiveness of βCD-TBZ/PBO complex at low concentration compared to commercial formulation of TBZ.

Effects of different drying treatments on fungal population and ochratoxin A occurrence in sultana type grapes.

PubMed

Şen, Levent; Ocak, İjlal; Nas, Sebahattin; Şevik, Ramazan

2016-09-01

This study aimed to determine the changes in mould and ochratoxin A (OTA) occurrence in sultanas under three different conventional drying conditions. Five different vineyards were chosen, and the three different treatments were applied to these grapes while drying. At the end of the drying process, total mould and black aspergilli (BA) populations in the samples varied from 2.45 to 5.61 log colony-forming units (CFU) g(-)(1) and from 0 to 4.92 log CFU g(-)(1), respectively. Significant increases (p < 0.05) occurred in mould loads depending on the extending drying period. However, independent of vineyard location, all the samples treated with cold dipping solution showed the lowest fungal loads. These results indicate that dipping solution treatment was the most effective drying method to minimise fungal infection of grapes. The expected results could not be achieved by drying grapes artificially contaminated with ochratoxigenic Aspergillus carbonarius spores. Seventy-one of 96 isolates (73.95%) obtained during drying were Aspergillus spp., and the remaining (n = 25, 26.05%) belonged to other genera, such as Penicillium, Trichoderma and Cladosporium. Grape juice-based agar medium was used to determine the realistic OTA production capacities of the isolated mould strains. The highest OTA production capacities were 809.70 ± 9.19, 87.58 ± 16.89 and 45.44 ± 18.78 ng g(-1) in 50% grape juice agar (GJ50), all five of which were from A. niger isolates. OTA was not present in any sample during the drying period; however, OTA was detected in two samples at 0.32 ± 0.15 and 0.52 ± 0.36 µg kg(-)(1) after the end of the drying process. The limit of detection (LOD) and limit of quantitation (LOQ) of the method used for detecting OTA in samples were 0.1 and 0.3 µg kg(-)(1), respectively.

Galactomyces geotrichum - moulds from dairy products with high biotechnological potential.

PubMed

Grygier, Anna; Myszka, Kamila; Rudzińska, Magdalena

2017-01-01

The article reviews the properties of the Galactomyces geotrichum species, the mould that is most important for the dairy industry. G. geotrichum mould has been isolated from milk, cheeses and alcoholic beverage. Its presence in food products makes it possible to obtain a characteristic aroma and taste, which corresponds to the needs and preferences of consumers. G. geotrichum plays an important role in ecology, where the mould is employed for the degradation of various hazardous substances and wastewater treatment. It has also been found to have potential for biofuel production. In addition to this, G. geotrichum can be applicable in two further major areas: agriculture and health protection.

Influence of composition of diluent on populations of yeasts and moulds recovered from raw fruits.

PubMed

Beuchat, L R; Scouten, A J; Jablonska, J

2002-01-01

The aims of this study were (i) to determine the retention of viability of mycoflora removed from raw fruits, and how this affected diluents used to prepare samples for enumeration of propagules, and (ii) to evaluate the performance of recovery media for supporting colony development. Yeasts and moulds removed from seven types of raw fruit were held in seven diluents for 1 h before plating on dichloran rose bengal chloramphenicol (DRBC) agar and plate count agar supplemented with chloramphenicol (100 micro g ml-1) (PCAC). Significant reductions (P=0.05) in populations of yeasts, moulds, and yeasts plus moulds occurred within the 1 h holding period, regardless of diluent composition. Overall, retention of viability was not influenced by diluent composition, and neither DRBC agar nor PCAC were superior in supporting colony development. The composition of diluents used to prepare food samples for mycological analysis has little affect on the number of yeasts and moulds recovered from seven types of naturally contaminated raw fruit. Both DRBC agar and PCAC are suitable as enumeration media. Diluents and media most often recommended for enumerating yeasts and moulds in foods are appropriate for raw fruits.

Comparison of custom-moulded ankle orthosis with hinged joints and off-the-shelf ankle braces in preventing ankle sprain in lateral cutting movements.

PubMed

Lee, Winson C C; Kobayashi, Toshiki; Choy, Barton T S; Leung, Aaron K L

2012-06-01

A custom moulded ankle orthosis with hinged joints potentially offers a better control over the subtalar joint and the ankle joint during lateral cutting movements, due to total contact design and increase in material strength. To test the above hypothesis by comparing it to three other available orthoses. Repeated measures. Eight subjects with a history of ankle sprains (Grade 2), and 11 subjects without such history performed lateral cutting movements in four test conditions: 1) non-orthotic, 2) custom-moulded ankle orthosis with hinges, 3) Sport-Stirrup, and 4) elastic ankle sleeve with plastic support. A VICON motion analysis system was used to study the motions at the ankle and subtalar joints. The custom-moulded ankle orthosis significantly lowered the inversion angle at initial contact (p = 0.006) and the peak inversion angle (p = 0.000) during lateral cutting movements in comparison to non-orthotic condition, while the other two orthoses did not. The three orthoses did not affect the plantarflexion motions, which had been suggested by previous studies to be important in shock wave attenuation. The custom-moulded ankle orthosis with hinges could better control inversion and thus expected to better prevent ankle sprain in lateral cutting movements. Custom-moulded ankle orthoses are not commonly used in preventing ankle sprains. This study raises the awareness of the use of custom-moulded ankle orthoses which are expected to better prevent ankle sprains.

Cheap and fast measuring roughness on big surfaces with an imprint method

NASA Astrophysics Data System (ADS)

Schopf, C.; Liebl, J.; Rascher, R.

2017-10-01

Roughness, shape and structure of a surface offer information on the state, shape and surface characteristics of a component. Particularly the roughness of the surface dictates the subsequent polishing of the optical surface. The roughness is usually measured by a white light interferometer, which is limited by the size of the components. Using a moulding method of surfaces that are difficult to reach, an imprint is taken and analysed regarding to roughness and structure. This moulding compound method is successfully used in dental technology. In optical production, the moulding compound method is advantageous in roughness determination in inaccessible spots or on large components (astrological optics). The "replica method" has been around in metal analysis and processing. Film is used in order to take an impression of a surface. Then, it is analysed for structures. In optical production, compound moulding seems advantageous in roughness determination in inaccessible spots or on large components (astrological optics). In preliminary trials, different glass samples with different roughness levels were manufactured. Imprints were taken from these samples (based on DIN 54150 "Abdruckverfahren für die Oberflächenprüfung"). The objective of these feasibility tests was to determine the limits of this method (smallest roughness determinable / highest roughness). The roughness of the imprint was compared with the roughness of the glass samples. By comparing the results, the uncertainty of the measuring method was determined. The spectrum for the trials ranged from rough grind (0.8 μm rms), over finishing grind (0.6 μm rms) to polishing (0.1 μm rms).

Light weight optics made by glass thermal forming for future x-ray telescopes

NASA Astrophysics Data System (ADS)

Winter, Anita; Vongehr, Monika; Friedrich, Peter

2010-07-01

Future X-ray observatory missions, such as IXO or Gen-X, require grazing incidence optics of large collecting area in combination with a very good angular resolution. Wolter type I X-ray telescopes made of slumped glass segments could be a possible alternative to silicon pore optics. To achieve these requirements we develop slumping methods for high accuracy segments by experimental means. In particular, we follow the approach of indirect slumping and aim to produce parabola and hyperbola in one piece. In order to avoid internal stress in the glass segments the thermal expansion coefficient of the glass should closely match the thermal expansion of the mould material. Currently we focus on a combination of the alloy KOVAR for the mould and D263 for the glass; additionally a platinum-coated silica as mould material is studied. We investigate the behaviour of both materials during slumping in order to obtain the ideal environment for the slumping process. Additionally we report on the design of different metrology methods to measure the figure and thickness variations of the glass segments in visual light, e.g. interference, and on bearings used for shape measurements and integration.

Phase-field modelling of microstructure formation during the solidification of continuously cast low carbon and HSLA steels

NASA Astrophysics Data System (ADS)

Böttger, B.; Apel, M.; Santillana, B.; Eskin, D. G.

2012-07-01

Cracking in continuous casting of steels has been one of the main problems for decades. Many of the cracks that occur during solidification are hot tears. To better understand the factors leading to this defect, microstructure formation is simulated for a low carbon (LCAK) and two high strength low alloyed (HSLA) steel grades during the initial stage of the process where the first solidified shell is formed inside the mould and where breakouts typically occur. 2D simulation is performed using the multiphase-field software MICRESS [1], which is coupled to the thermodynamic database TCFE6 [2] and the mobility database MOB2 [2], taking into account all elements which may have a relevant effect on the mechanical properties and structure formation during or subsequent to solidification. The use of a moving-frame boundary condition allows travelling through the entire solidification history starting from the slab surface, and tracking the morphology changes during growth of the shell. A heterogeneous nucleation model is included to permit the description of morphological transitions between the initial solidification and the subsequent columnar growth region. Furthermore, a macroscopic one-dimensional temperature solver is integrated to account for the transient and nonlinear temperature field during the initial stage of continuous casting. The external heat flux boundary conditions for this process were derived from thermal process data of the industrial slab caster. The simulation results for the three steel grades have been validated by thickness measurements of breakout shells and microstructure observation of the corresponding grades. Furthermore, the primary dendrite spacing has been measured across the whole thickness of the shell and compared with the simulated microstructures. Significant microstructure differences between the steel grades are discussed and correlated with their hot-cracking behavior.

Method for forming consumable electrodes from metallic chip scraps

DOEpatents

Girshov, Vladimir Leonidovich; Podpalkin, Arcady Munjyvich; Treschevskiy, Arnold Nikolayevich; Abramov, Alexey Alexandrovich

2005-10-11

The method relates to metallurgical recycling of waste products, preferably titanium alloys chips scrap. Accordingly after crushing and cleaning, the chip scrap is subjected to vacuum-thermal degassing (VTD); the chip scrap is pressed into briquettes; the briquettes are placed into a mould allowing sufficient remaining space for the addition of molten metal alloy; the mould is pre-heated before filling with the molten metal alloy; the mould remaining space is filled with molten metal alloy. After cooling, the electrode is removed from the mould. The method provides a means for 100% use of chip scrap in producing consumable electrodes having increased mechanical strength and reduced interstitial impurities content leading to improved secondary cast alloys.

Moulding technique demonstrates the contribution of surface geometry to the super-hydrophobic properties of the surface of a water strider.

PubMed

Goodwyn, Pablo Perez; De Souza, Emerson; Fujisaki, Kenji; Gorb, Stanislav

2008-05-01

Water striders (Insecta, Heteroptera, Gerridae) have a complex three-dimensional waterproof hairy cover which renders them super-hydrophobic. This paper experimentally demonstrates for the first time the mechanism of the super-hydrophobicity of the cuticle of water striders. The complex two-level microstructure of the surface, including the smallest microtrichia (200-300 nm wide, 7-9 microm long), was successfully replicated using a two-step moulding technique. The mould surface exhibited super-hydrophobic properties similar to the original insect surface. The average water contact angle (CA) of the mould was 164.7 degrees , whereas the CA of the flat polymer was about 92 degrees . These results show that (i) in water striders, the topography of the surface plays a dominant role in super-hydrophobicity, (ii) very low surface energy bulk material (typically smaller than 0.020 N m(-1)) is not necessary to achieve super-hydrophobicity; and (3) the two-step moulding technique may be used to mimic quite complex biological functional surfaces.

Consensus guidelines for the treatment of invasive mould infections in haematological malignancy and haemopoietic stem cell transplantation, 2014.

PubMed

Blyth, C C; Gilroy, N M; Guy, S D; Chambers, S T; Cheong, E Y; Gottlieb, T; McGuinness, S L; Thursky, K A

2014-12-01

Mould species represent the pathogens most commonly associated with invasive fungal disease in patients with haematological malignancies and patients of haemopoietic stem cell transplants. Invasive mould infections in these patient populations, particularly in the setting of neutropenia, are associated with high morbidity and mortality, and significantly increase the complexity of management. While Aspergillus species remain the most prevalent cause of invasive mould infections, Scedosporium and Fusarium species and the Mucormycetes continue to place a significant burden on the immunocompromised host. Evidence also suggests that infections caused by rare and emerging pathogens are increasing within the setting of broad-spectrum antifungal prophylaxis and improved survival times placing immunosuppressed patients at risk for longer. These guidelines present evidence-based recommendations for the antifungal management of common, rare and emerging mould infections in both adult and paediatric populations. Where relevant, the role of surgery, adjunctive therapy and immunotherapy is also discussed. © 2014 The Authors; Internal Medicine Journal © 2014 Royal Australasian College of Physicians.

Effect of applying cinnamaldehyde incorporated in wax on green mould decay in citrus fruits.

PubMed

Duan, Xiaofang; OuYang, Qiuli; Tao, Nengguo

2018-01-01

Green mould caused by Penicillium digitatum is the most damaging postharvest diseases of citrus fruit. Cinnamaldehyde (CA) is a food additive that has potential use in controlling postharvest disease of fruits and vegetables. In this study, the effectiveness of wax with CA (WCA) in controlling Ponkan (Citrus reticulata Blanco) green mould was investigated. The mycelial growth of P. digitatum was inhibited by CA in a dose-dependent manner. The minimum inhibitory concentration and minimum fungicidal concentration (MFC) were both 0.50 mL L -1 . In vivo tests demonstrated that WCA (1 × and 10 × MFC) applied to Ponkan fruits inoculated with P. digitatum could significantly decrease the incidence of green mould for up to 5 days. The WCA treatment increased the activities of catalase, superoxide dismutase, peroxidase, phenylalanine ammonia lyase, polyphenol oxidase, as well as the total phenols and flavonoids contents. Meanwhile, the treatment remarkably decreased the weight loss rate of fruits and maintained fruit quality. These results indicated that WCA treatment might induce defence responses against green mould in citrus fruit. Our findings suggest that WCA might be a promising approach in controlling green mould of citrus fruits. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Less invasive new vaginoplasty using laparoscopy, atelocollagen sponge, and hand-made mould.

PubMed

Miyahara, Yoshiya; Yoshida, Shigeki; Shirakawa, Tokuro; Makihara, Natsuko; Niiya, Kiyoshi; Ebina, Yasuhiko; Yamada, Hideto

2013-03-19

The purpose of this study was to validate the therapeutic efficacy of the innovative surgical approach using laparoscopy, atelocollagen sponge, and hand-made mould on the achievement of a satisfactory neovagina in patients with vaginal agenesis. The current study involved four patients diagnosed as having Mayer-Rokitansky-Küster-Hauser syndrome. After creating a vaginal tunnel, the mould wrapped with atelocollagen sponge was placed within the neovagina. The hand-made mould made of expanded polystyrene was started to insert into the neovagina at 7 days after operation. Since this mould is lighter and easier to adjust compared with the previous commercialized ones, it was less stressful for the patients to master the procedure than previous methods. Average operation time was 124 minutes with average blood loss being 45 ml. Average hospital stay was 23 days. The mean length of the neovagina one week postoperation was 8 cm with two fingers in width in all patients. No remarkable postoperative complications were noted. At two months after surgery, the neovagina was confirmed to be completely epithelialized in all patients, assessed by Schiller's test. This innovative surgical procedure using a mould wrapped with atelocollagen sponge may be a more useful approach for the treatment of vaginal agenesis.

Mycotoxin production capability of Penicillium roqueforti in strains isolated from mould-ripened traditional Turkish civil cheese.

PubMed

Cakmakci, Songul; Gurses, Mustafa; Hayaloglu, A Adnan; Cetin, Bulent; Sekerci, Pinar; Dagdemir, Elif

2015-01-01

Mould-ripened civil is a traditional cheese produced mainly in eastern Turkey. The cheese is produced with a mixture of civil and whey curd cheeses (lor). This mixture is pressed into goat skins or plastic bags and is ripened for more than three months. Naturally occurring moulds grow on the surface and inside of the cheese during ripening. In this research, 140 Penicillium roqueforti strains were isolated from 41 samples of mould-ripened civil cheese collected from Erzurum and around towns in eastern Turkey. All strains were capable of mycotoxin production and were analysed using an HPLC method. It was established that all the strains (albeit at very low levels) produced roquefortine C, penicillic acid, mycophenolic acid and patulin. The amounts of toxins were in the ranges 0.4-47.0, 0.2-43.6, 0.1-23.1 and 0.1-2.3 mg kg(-1), respectively. Patulin levels of the samples were lower than the others. The lowest level and highest total mycotoxin levels were determined as 1.2 and 70.1 mg kg(-1) respectively. The results of this preliminary study may help in the choice of secondary cultures for mould-ripened civil cheese and other mould-ripened cheeses.

Biocontrol of ochratoxigenic moulds (Aspergillus ochraceus and Penicillium nordicum) by Debaryomyces hansenii and Saccharomycopsis fibuligera during speck production.

PubMed

Iacumin, Lucilla; Manzano, Marisa; Andyanto, Debbie; Comi, Giuseppe

2017-04-01

Speck is a meat product obtained from the deboned leg of pork that is salted, smoked and seasoned for four to six months. During speck seasoning, Eurotium rubrum and Penicillium solitum grow on the surface and collaborate with other moulds and tissue enzymes to produce the typical aroma. Both of these strains usually predominate over other moulds. However, moulds producing ochratoxins, such as Aspergillus ochraceus and Penicillium nordicum, can also co-grow on speck and produce ochratoxin A (OTA). Consequently, speck could represent a potential health risk for consumers. Because A. ochraceus and P. nordicum could represent a problem for artisanal speck production, the aim of this study was to inhibit these mould strains using Debaryomyces hansenii and Saccharomycopsis fibuligera. Six D. hansenii and six S. fibuligera strains were tested in vitro to inhibit A. ochraceus and P. nordicum. The D. hansenii DIAL 1 and S. fibuligera DIAL 3 strains demonstrated the highest inhibitory activity and were selected for in vivo tests. The strains were co-inoculated on fresh meat cuts for speck production with both of the OTA-producing moulds prior to drying and seasoning. At the end of seasoning (six months), OTA was not detected in the speck treated with both yeast strains. Because the yeasts did not adversely affect the speck odour or flavour, the strains are proposed as starters for the inhibition of ochratoxigenic moulds. Copyright © 2016 Elsevier Ltd. All rights reserved.

Moulds contaminants on Norwegian dry-cured meat products.

PubMed

Asefa, Dereje T; Gjerde, Ragnhild O; Sidhu, Maan S; Langsrud, Solveig; Kure, Cathrine F; Nesbakken, Truls; Skaar, Ida

2009-01-15

Dry-cured meat production has a long tradition in Norway. However, uncontrolled mould growth on the surface of the dry-cured meat products is causing significant quality problems. As some moulds are mycotoxigenic, their growth on the dry-cured meat products could also pose a serious health risk. Such quality problems and potential health risks can be better handled if the types of moulds growing on the products are known. In total, 161 samples were collected from the ripening and packaging stages of production with the aim of identifying moulds contaminating smoked and unsmoked Norwegian dry-cured meat products. Moulds were isolated either by transferring aerial mycelium of each visible mould colonies on the products or by directly plating pieces of meat on suitable agar media. The isolates were identified at a species level by a polyphasic approach. In total, 264 isolates belonging to 20 species and four fungal genera were identified. The genus Penicillium covered 88.3% of the total isolates. This genus contributed to the isolates of smoked and unsmoked products by 91% and 84% respectively. Penicillium nalgiovense was the dominant species isolated from both smoked and unsmoked products and covered 38% of the total isolates. Penicillium solitum and P. commune were the next most frequently isolated species with a contribution of 13% and 10% respectively. Species of Cladosporium and Eurotium contributed to the total isolates by 6% and 4.9% respectively. Smoking seems to affect the growth of these dominating species differently. An increase in the isolation frequency of P. nalgiovense accompanied by the reduction in the occurrence of P. solitum, P. commune and species of Cladosporium was observed on smoked products. The survey showed that the species of Penicillium are associated with Norwegian dry-cured meat products in general. Penicillium nalgiovense, the dominating mould species, is a potential producer of penicillin and its presence could represent a threat to allergic consumers.

Surface roughness of glass ionomer cements indicated for uncooperative patients according to surface protection treatment

PubMed Central

Pacifici, Edoardo; Bossù, Maurizio; Giovannetti, Agostino; La Torre, Giuseppe; Guerra, Fabrizio; Polimeni, Antonella

2013-01-01

Summary Background Even today, use of Glass Ionomer Cements (GIC) as restorative material is indicated for uncooperative patients. Aim The study aimed at estimating the surface roughness of different GICs using or not their proprietary surface coatings and at observing the interfaces between cement and coating through SEM. Materials and methods Forty specimens have been obtained and divided into 4 groups: Fuji IX (IX), Fuji IX/G-Coat Plus (IXC), Vitremer (V), Vitremer/Finishing Gloss (VFG). Samples were obtained using silicone moulds to simulate class I restorations. All specimens were processed for profilometric evaluation. The statistical differences of surface roughness between groups were assessed using One-Way Analysis of Variance (One-Way ANOVA) (p<0.05). The Two-Way Analysis of Variance (Two-Way ANOVA) was used to evaluate the influence of two factors: restoration material and presence of coating. Coated restoration specimens (IXC and VFG) were sectioned perpendicular to the restoration surface and processed for SEM evaluation. Results No statistical differences in roughness could be noticed between groups or factors. Following microscopic observation, interfaces between restoration material and coating were better for group IXC than for group VFG. Conclusions When specimens are obtained simulating normal clinical procedures, the presence of surface protection does not significantly improve the surface roughness of GICs. PMID:24611090

Surface roughness of glass ionomer cements indicated for uncooperative patients according to surface protection treatment.

PubMed

Pacifici, Edoardo; Bossù, Maurizio; Giovannetti, Agostino; La Torre, Giuseppe; Guerra, Fabrizio; Polimeni, Antonella

2013-01-01

Even today, use of Glass Ionomer Cements (GIC) as restorative material is indicated for uncooperative patients. The study aimed at estimating the surface roughness of different GICs using or not their proprietary surface coatings and at observing the interfaces between cement and coating through SEM. Forty specimens have been obtained and divided into 4 groups: Fuji IX (IX), Fuji IX/G-Coat Plus (IXC), Vitremer (V), Vitremer/Finishing Gloss (VFG). Samples were obtained using silicone moulds to simulate class I restorations. All specimens were processed for profilometric evaluation. The statistical differences of surface roughness between groups were assessed using One-Way Analysis of Variance (One-Way ANOVA) (p<0.05). The Two-Way Analysis of Variance (Two-Way ANOVA) was used to evaluate the influence of two factors: restoration material and presence of coating. Coated restoration specimens (IXC and VFG) were sectioned perpendicular to the restoration surface and processed for SEM evaluation. No statistical differences in roughness could be noticed between groups or factors. Following microscopic observation, interfaces between restoration material and coating were better for group IXC than for group VFG. When specimens are obtained simulating normal clinical procedures, the presence of surface protection does not significantly improve the surface roughness of GICs.

Abridged version of the AWMF guideline for the medical clinical diagnostics of indoor mould exposure: S2K Guideline of the German Society of Hygiene, Environmental Medicine and Preventive Medicine (GHUP) in collaboration with the German Association of Allergists (AeDA), the German Society of Dermatology (DDG), the German Society for Allergology and Clinical Immunology (DGAKI), the German Society for Occupational and Environmental Medicine (DGAUM), the German Society for Hospital Hygiene (DGKH), the German Society for Pneumology and Respiratory Medicine (DGP), the German Mycological Society (DMykG), the Society for Pediatric Allergology and Environmental Medicine (GPA), the German Federal Association of Pediatric Pneumology (BAPP), and the Austrian Society for Medical Mycology (ÖGMM).

PubMed

Wiesmüller, Gerhard A; Heinzow, Birger; Aurbach, Ute; Bergmann, Karl-Christian; Bufe, Albrecht; Buzina, Walter; Cornely, Oliver A; Engelhart, Steffen; Fischer, Guido; Gabrio, Thomas; Heinz, Werner; Herr, Caroline E W; Kleine-Tebbe, Jörg; Klimek, Ludger; Köberle, Martin; Lichtnecker, Herbert; Lob-Corzilius, Thomas; Merget, Rolf; Mülleneisen, Norbert; Nowak, Dennis; Rabe, Uta; Raulf, Monika; Seidl, Hans Peter; Steiß, Jens-Oliver; Szewszyk, Regine; Thomas, Peter; Valtanen, Kerttu; Hurraß, Julia

2017-01-01

This article is an abridged version of the AWMF mould guideline "Medical clinical diagnostics of indoor mould exposure" presented in April 2016 by the German Society of Hygiene, Environmental Medicine and Preventive Medicine ( Gesellschaft für Hygiene, Umweltmedizin und Präventivmedizin, GHUP ), in collaboration with the above-mentioned scientific medical societies, German and Austrian societies, medical associations and experts. Indoor mould growth is a potential health risk, even if a quantitative and/or causal relationship between the occurrence of individual mould species and health problems has yet to be established. Apart from allergic bronchopulmonary aspergillosis (ABPA) and mould-caused mycoses, only sufficient evidence for an association between moisture/mould damage and the following health effects has been established: allergic respiratory disease, asthma (manifestation, progression and exacerbation), allergic rhinitis, hypersensitivity pneumonitis (extrinsic allergic alveolitis), and increased likelihood of respiratory infections/bronchitis. In this context the sensitizing potential of moulds is obviously low compared to other environmental allergens. Recent studies show a comparatively low sensitizing prevalence of 3-10% in the general population across Europe. Limited or suspected evidence for an association exist with respect to mucous membrane irritation and atopic eczema (manifestation, progression and exacerbation). Inadequate or insufficient evidence for an association exist for chronic obstructive pulmonary disease, acute idiopathic pulmonary hemorrhage in children, rheumatism/arthritis, sarcoidosis and cancer. The risk of infection posed by moulds regularly occurring indoors is low for healthy persons; most species are in risk group 1 and a few in risk group 2 ( Aspergillus fumigatus, A. flavus ) of the German Biological Agents Act ( Biostoffverordnung ). Only moulds that are potentially able to form toxins can be triggers of toxic reactions. Whether or not toxin formation occurs in individual cases is determined by environmental and growth conditions, above all the substrate. In the case of indoor moisture/mould damage, everyone can be affected by odour effects and/or mood disorders. However, this is not a health hazard. Predisposing factors for odour effects can include genetic and hormonal influences, imprinting, context and adaptation effects. Predisposing factors for mood disorders may include environmental concerns, anxiety, condition, and attribution, as well as various diseases. Risk groups to be protected particularly with regard to an infection risk are persons on immunosuppression according to the classification of the German Commission for Hospital Hygiene and Infection Prevention ( Kommission für Krankenhaushygiene und Infektionsprävention, KRINKO ) at the Robert Koch- Institute (RKI) and persons with cystic fibrosis (mucoviscidosis); with regard to an allergic risk, persons with cystic fibrosis (mucoviscidosis) and patients with bronchial asthma should be protected. The rational diagnostics include the medical history, physical examination, and conventional allergy diagnostics including provocation tests if necessary; sometimes cellular test systems are indicated. In the case of mould infections the reader is referred to the AWMF guideline "Diagnosis and Therapy of Invasive Aspergillus Infections". With regard to mycotoxins, there are currently no useful and validated test procedures for clinical diagnostics. From a preventive medicine standpoint it is important that indoor mould infestation in relevant dimension cannot be tolerated for precautionary reasons. With regard to evaluating the extent of damage and selecting a remedial procedure, the reader is referred to the revised version of the mould guideline issued by the German Federal Environment Agency ( Umweltbundesamt, UBA ).

Application of waste bulk moulded composite (BMC) as a filler for isotactic polypropylene composites.

PubMed

Barczewski, Mateusz; Matykiewicz, Danuta; Andrzejewski, Jacek; Skórczewska, Katarzyna

2016-05-01

The aim of this study was to produce isotactic polypropylene based composites filled with waste thermosetting bulk moulded composite (BMC). The influence of BMC waste addition (5, 10, 20 wt%) on composites structure and properties was investigated. Moreover, additional studies of chemical treatment of the filler were prepared. Modification of BMC waste by calcium stearate (CaSt) powder allows to assess the possibility of the production of composites with better dispersion of the filler and more uniform properties. The mechanical, processing, and thermal properties, as well as structural investigations were examined by means of static tensile test, Dynstat impact strength test, differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), melt flow index (MFI) and scanning electron microscopy (SEM). Developed composites with different amounts of non-reactive filler exhibited satisfactory thermal and mechanical properties. Moreover, application of the low cost modifier (CaSt) allows to obtain composites with better dispersion of the filler and improved processability.

Application of waste bulk moulded composite (BMC) as a filler for isotactic polypropylene composites

PubMed Central

Barczewski, Mateusz; Matykiewicz, Danuta; Andrzejewski, Jacek; Skórczewska, Katarzyna

2016-01-01

The aim of this study was to produce isotactic polypropylene based composites filled with waste thermosetting bulk moulded composite (BMC). The influence of BMC waste addition (5, 10, 20 wt%) on composites structure and properties was investigated. Moreover, additional studies of chemical treatment of the filler were prepared. Modification of BMC waste by calcium stearate (CaSt) powder allows to assess the possibility of the production of composites with better dispersion of the filler and more uniform properties. The mechanical, processing, and thermal properties, as well as structural investigations were examined by means of static tensile test, Dynstat impact strength test, differential scanning calorimetry (DSC), wide angle X-ray scattering (WAXS), melt flow index (MFI) and scanning electron microscopy (SEM). Developed composites with different amounts of non-reactive filler exhibited satisfactory thermal and mechanical properties. Moreover, application of the low cost modifier (CaSt) allows to obtain composites with better dispersion of the filler and improved processability. PMID:27222742

Mechanical properties and microstructural evolution of vacuum hot-pressed titanium and Ti-6Al-7Nb alloy.

PubMed

Bolzoni, L; Ruiz-Navas, E M; Neubauer, E; Gordo, E

2012-05-01

Hot-pressing is a powder metallurgy process where loose powder is loaded into a mould, usually of graphite, and sintered by the simultaneous application of high temperature and pressure. In this study elemental titanium and Ti-6Al-7Nb alloy powders are hot-pressed under different conditions in order to study the influence of the processing parameters on the microstructure and mechanical properties. The samples are characterised in terms of relative density, microstructure, XRD, percentage of interstitials, three-point bending test and hardness. Relative densities as high as 99% are obtained, the oxygen and carbon content remains almost constant but nitrogen percentage increases. This is due to the interaction with the BN coated mould and leads to the formation of a reacted layer in the surface, composed by different titanium compounds, which greatly affect the mechanical properties. Nevertheless, the removal of this reacted layer leads to an important improvement of the ductility, especially for elemental titanium. Copyright © 2012 Elsevier Ltd. All rights reserved.

Spring-back simulation of unidirectional carbon/epoxy L- shaped laminate composites manufactured through autoclave processing

NASA Astrophysics Data System (ADS)

Nasir, M. N. M.; Mezeix, L.; Aminanda, Y.; Seman, M. A.; Rivai, A.; Ali, K. M.

2016-02-01

This paper presents an original method in predicting the spring-back for composite aircraft structures using non-linear Finite Element Analysis (FEA) and is an extension of the previous accompanying study on flat geometry samples. Firstly, unidirectional prepreg lay-up samples are fabricated on moulds with different corner angles (30°, 45° and 90°) and the effect on spring-back deformation are observed. Then, the FEA model that was developed in the previous study on flat samples is utilized. The model maintains the physical mechanisms of spring-back such as ply stretching and tool-part interface properties with the additional mechanism in the corner effect and geometrical changes in the tool, part and the tool-part interface components. The comparative study between the experimental data and FEA results show that the FEA model predicts adequately the spring-back deformation within the range of corner angle tested.

Effect of trehalose on the biocontrol efficacy of Pichia caribbica against post-harvest grey mould and blue mould decay of apples.

PubMed

Zhao, Lina; Zhang, Hongyin; Lin, Hetong; Zhang, Xiaoyun; Ren, Xiaofeng

2013-08-01

The influence of adding trehalose to the culture medium on the efficacy of Pichia caribbica (JSU-1) in controlling post-harvest grey mould and blue mould decay of apples and the possible mechanisms involved were investigated. The antagonistic activity of P. caribbica harvested from nutrient yeast dextrose broth (NYDB) amended with trehalose at 5 mg mL(-1) to post-harvest grey mould and blue mould decay was improved greatly compared with that without trehalose. The intracellular trehalose content of P. caribbica harvested from NYDB amended with trehalose at 5 mg mL(-1) was higher than that of P. caribbica harvested from NYDB. The population of P. caribbica could rapidly colonise and grow in apple wounds. Moreover, the application of P. caribbica cultivated in the culture medium of the trehalose supplement (5 mg mL(-1) ) induced higher polyphenoloxidase (PPO) and peroxidase (POD) activity of apples compared with that cultivated by P. caribbica in the NYDB. SEM results suggested that P. caribbica harvested from NYDB amended with trehalose at 5 mg mL(-1) showed stronger inhibition efficacy to Botrytis cinerea than P. caribbica harvested from NYDB. The antagonistic activity of P. caribbica can be enhanced by adding trehalose to the medium. © 2012 Society of Chemical Industry.

Low Female Literacy: Factors and Strategies

ERIC Educational Resources Information Center

Vasudeva Rao, B. S.; Gupta, P. Viswanadha

2006-01-01

Literacy is a process which dispels and promotes rational thinking and moulds human beings into becoming responsible citizens. The absence of literacy directly and indirectly retards the development of individuals, society, community and the country. For the success of any program, people should be motivated by providing necessary congenial…

Numerical Simulation of Thermal Performance of Glass-Fibre-Reinforced Polymer

NASA Astrophysics Data System (ADS)

Zhao, Yuchao; Jiang, Xu; Zhang, Qilin; Wang, Qi

2017-10-01

Glass-Fibre-Reinforced Polymer (GFRP), as a developing construction material, has a rapidly increasing application in civil engineering especially bridge engineering area these years, mainly used as decorating materials and reinforcing bars for now. Compared with traditional construction material, these kinds of composite material have obvious advantages such as high strength, low density, resistance to corrosion and ease of processing. There are different processing methods to form members, such as pultrusion and resin transfer moulding (RTM) methods, which process into desired shape directly through raw material; meanwhile, GFRP, as a polymer composite, possesses several particular physical and mechanical properties, and the thermal property is one of them. The matrix material, polymer, performs special after heated and endue these composite material a potential hot processing property, but also a poor fire resistance. This paper focuses on thermal performance of GFRP as panels and corresponding researches are conducted. First, dynamic thermomechanical analysis (DMA) experiment is conducted to obtain the glass transition temperature (Tg) of the object GFRP, and the curve of bending elastic modulus with temperature is calculated according to the experimental data. Then compute and estimate the values of other various thermal parameters through DMA experiment and other literatures, and conduct numerical simulation under two condition respectively: (1) the heat transfer process of GFRP panel in which the panel would be heated directly on the surface above Tg, and the hot processing under this temperature field; (2) physical and mechanical performance of GFRP panel under fire condition. Condition (1) is mainly used to guide the development of high temperature processing equipment, and condition (2) indicates that GFRP’s performance under fire is unsatisfactory, measures must be taken when being adopted. Since composite materials’ properties differ from each other and their high temperature parameters can’t be obtained through common methods, some parameters are estimated, the simulation is to guide the actual high temperature experiment, and the parameters will also be adjusted by then.

Aspergillus fumigatus and mesophilic moulds in air in the surrounding environment downwind of non-hazardous waste landfill sites.

PubMed

Schlosser, Olivier; Robert, Samuel; Debeaupuis, Catherine

2016-05-01

Non-hazardous waste landfilling has the potential to release biological agents into the air, notably mould spores. Some species, such as Aspergillus fumigatus, may be a cause of concern for at-risk nearby residents. However, air concentration in the surrounding environment of non-hazardous waste landfill sites is poorly documented. An extensive sampling programme was designed to investigate the relationship between culturable mesophilic moulds and A. fumigatus concentrations in air and distance downwind of non-hazardous waste landfill sites. On-site and off-site repeated measurements were performed at four landfill sites during cold and warm seasons. A high-flow air-sampler device was selected so as to allow peak concentration measurement. Linear mixed-effects models were used to explain variability in the concentrations in air over time and across sites, seasons, instantaneous meteorological conditions and discharged waste tonnage. Concentrations of mesophilic moulds and A. fumigatus at off-site upwind sampling locations were compared with concentrations at each of the downwind sampling locations. At the tipping face location, peak concentration reached 480,000CFUm(-3) for mesophilic moulds and 9300CFUm(-3) for A. fumigatus. Compared with upwind background levels, these concentrations were, on average, approximately 20 and 40 times higher respectively. A steep decline in the concentration of both mesophilic moulds and A. fumigatus was observed between the tipping face location and the downwind property boundary (reduction by 77% and 84% respectively), followed by a low decline leading to a 90% and 94% reduction in concentration at 200m from the property boundary and beyond. With the 200m and 500m downwind sampling point values added together, the 97.5th percentile of concentration was 6013CFUm(-3) and 87CFUm(-3) for mesophilic moulds and A. fumigatus, respectively. Other determining factors were the discharged waste tonnage, the season, instantaneous temperature and wind velocity for mesophilic mould, and instantaneous temperature for A. fumigatus. At 200m and 500 downwind from the property boundary, mesophilic moulds and A. fumigatus concentrations were still higher than the local background level. However, whilst statistically significant, this increase does not suggest an excess risk to nearby residents' health when compared with the wide range of outdoor background levels reported in literature. These findings suggest that moulds and A. fumigatus may be transported beyond 200m from the property boundary in concentrations above those found locally upwind of the landfill site. Nevertheless, for exposure assessment purposes, comparison should also be made with background levels in wider areas which are either residential or through which people travel to work for example. Copyright © 2016 Elsevier GmbH. All rights reserved.

Habituation in non-neural organisms: evidence from slime moulds.

PubMed

Boisseau, Romain P; Vogel, David; Dussutour, Audrey

2016-04-27

Learning, defined as a change in behaviour evoked by experience, has hitherto been investigated almost exclusively in multicellular neural organisms. Evidence for learning in non-neural multicellular organisms is scant, and only a few unequivocal reports of learning have been described in single-celled organisms. Here we demonstrate habituation, an unmistakable form of learning, in the non-neural organism Physarum polycephalum In our experiment, using chemotaxis as the behavioural output and quinine or caffeine as the stimulus, we showed that P. polycephalum learnt to ignore quinine or caffeine when the stimuli were repeated, but responded again when the stimulus was withheld for a certain time. Our results meet the principle criteria that have been used to demonstrate habituation: responsiveness decline and spontaneous recovery. To distinguish habituation from sensory adaptation or motor fatigue, we also show stimulus specificity. Our results point to the diversity of organisms lacking neurons, which likely display a hitherto unrecognized capacity for learning, and suggest that slime moulds may be an ideal model system in which to investigate fundamental mechanisms underlying learning processes. Besides, documenting learning in non-neural organisms such as slime moulds is centrally important to a comprehensive, phylogenetic understanding of when and where in the tree of life the earliest manifestations of learning evolved. © 2016 The Author(s).

Habituation in non-neural organisms: evidence from slime moulds

PubMed Central

Boisseau, Romain P.; Vogel, David; Dussutour, Audrey

2016-01-01

Learning, defined as a change in behaviour evoked by experience, has hitherto been investigated almost exclusively in multicellular neural organisms. Evidence for learning in non-neural multicellular organisms is scant, and only a few unequivocal reports of learning have been described in single-celled organisms. Here we demonstrate habituation, an unmistakable form of learning, in the non-neural organism Physarum polycephalum. In our experiment, using chemotaxis as the behavioural output and quinine or caffeine as the stimulus, we showed that P. polycephalum learnt to ignore quinine or caffeine when the stimuli were repeated, but responded again when the stimulus was withheld for a certain time. Our results meet the principle criteria that have been used to demonstrate habituation: responsiveness decline and spontaneous recovery. To distinguish habituation from sensory adaptation or motor fatigue, we also show stimulus specificity. Our results point to the diversity of organisms lacking neurons, which likely display a hitherto unrecognized capacity for learning, and suggest that slime moulds may be an ideal model system in which to investigate fundamental mechanisms underlying learning processes. Besides, documenting learning in non-neural organisms such as slime moulds is centrally important to a comprehensive, phylogenetic understanding of when and where in the tree of life the earliest manifestations of learning evolved. PMID:27122563

Rapid prototyping of interfacing microcomponents for printed circuit board-level optical interconnects

NASA Astrophysics Data System (ADS)

Van Erps, Jürgen; Vervaeke, Michael; Thienpont, Hugo

2012-01-01

One of the important challenges for the deployment of the emerging breed of nanotechnology components is interfacing them with the external world, preferably accomplished with low-cost micro-optical devices. For the fabrication of this kind of micro-optical components, we make use of deep proton writing (DPW) as a generic rapid prototyping technology. DPW consists of bombarding polymer samples with swift protons, which results after chemical processing steps in high quality micro-optical components. The strength of the DPW micro-machining technology is the ability to fabricate monolithic building blocks that include micro-optical and mechanical functionalities which can be precisely integrated into more complex photonic systems. In this paper we give an overview of the process steps of the technology and we present several examples of micro-optical and micro-mechanical components, fabricated through DPW, targeting applications in printed circuit baordlevel optical interconnections. These include: high-precision 2-D fiber connectors, discrete out-of-plane coupling structures featuring high-quality 45° and curved micro-mirrors, arrays of high aspect ratio micro-pillars and backplane connectors. While DPW is clearly not a mass fabrication technique as such, one of its assets is that once the master component has been prototyped, a metal mould can be generated from the DPW master by applying electroplating. After removal of the plastic master, this metal mould can be used as a shim in a final microinjection moulding or hot embossing step. This way, the master component can be mass-produced at low cost in a wide variety of high-tech plastics.

Occurrence, distribution and contamination levels of heat-resistant moulds throughout the processing of pasteurized high-acid fruit products.

PubMed

Santos, Juliana Lane Paixão Dos; Samapundo, Simbarashe; Biyikli, Ayse; Van Impe, Jan; Akkermans, Simen; Höfte, Monica; Abatih, Emmanuel Nji; Sant'Ana, Anderson S; Devlieghere, Frank

2018-05-19

Heat-resistant moulds (HRMs) are well known for their ability to survive pasteurization and spoil high-acid food products, which is of great concern for processors of fruit-based products worldwide. Whilst the majority of the studies on HRMs over the last decades have addressed their inactivation, few data are currently available regarding their contamination levels in fruit and fruit-based products. Thus, this study aimed to quantify and identify heat-resistant fungal ascospores from samples collected throughout the processing of pasteurized high-acid fruit products. In addition, an assessment on the effect of processing on the contamination levels of HRMs in these products was carried out. A total of 332 samples from 111 batches were analyzed from three processing plants (=three processing lines): strawberry puree (n = 88, Belgium), concentrated orange juice (n = 90, Brazil) and apple puree (n = 154, the Netherlands). HRMs were detected in 96.4% (107/111) of the batches and 59.3% (197/332) of the analyzed samples. HRMs were present in 90.9% of the samples from the strawberry puree processing line (1-215 ascospores/100 g), 46.7% of the samples from the orange juice processing line (1-200 ascospores/100 g) and 48.7% of samples from the apple puree processing line (1-84 ascospores/100 g). Despite the high occurrence, the majority (76.8%, 255/332) of the samples were either not contaminated or presented low levels of HRMs (<10 ascospores/100 g). For both strawberry puree and concentrated orange juice, processing had no statistically significant effect on the levels of HRMs (p > 0.05). On the contrary, a significant reduction (p < 0.05) in HRMs levels was observed during the processing of apple puree. Twelve species were identified belonging to four genera - Byssochlamys, Aspergillus with Neosartorya-type ascospores, Talaromyces and Rasamsonia. N. fumigata (23.6%), N. fischeri (19.1%) and B. nivea (5.5%) were the predominant species in pasteurized products. The quantitative data (contamination levels of HRMs) were fitted to exponential distributions and will ultimately be included as input to spoilage risk assessment models which would allow better control of the spoilage of heat treated fruit products caused by heat-resistant moulds. Copyright © 2018 Elsevier B.V. All rights reserved.

Airborne emissions of carcinogens and respiratory sensitizers during thermal processing of plastics.

PubMed

Unwin, John; Coldwell, Matthew R; Keen, Chris; McAlinden, John J

2013-04-01

Thermoplastics may contain a wide range of additives and free monomers, which themselves may be hazardous substances. Laboratory studies have shown that the thermal decomposition products of common plastics can include a number of carcinogens and respiratory sensitizers, but very little information exists on the airborne contaminants generated during actual industrial processing. The aim of this work was to identify airborne emissions during thermal processing of plastics in real-life, practical applications. Static air sampling was conducted at 10 industrial premises carrying out compounding or a range of processes such as extrusion, blown film manufacture, vacuum thermoforming, injection moulding, blow moulding, and hot wire cutting. Plastics being processed included polyvinyl chloride, polythene, polypropylene, polyethylene terephthalate, and acrylonitrile-butadiene-styrene. At each site, static sampling for a wide range of contaminants was carried out at locations immediately adjacent to the prominent fume-generating processes. The monitoring data indicated the presence of few carcinogens at extremely low concentrations, all less than 1% of their respective WEL (Workplace Exposure Limit). No respiratory sensitizers were detected at any sites. The low levels of process-related fume detected show that the control strategies, which employed mainly forced mechanical general ventilation and good process temperature control, were adequate to control the risks associated with exposure to process-related fume. This substantiates the advice given in the Health and Safety Executive's information sheet No 13, 'Controlling Fume During Plastics Processing', and its broad applicability in plastics processing in general.

44. LOOKING SOUTH IN MOULD CONDITIONING BUILDING, WITH HOT TOPPING ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

44. LOOKING SOUTH IN MOULD CONDITIONING BUILDING, WITH HOT TOPPING PLATFORM ON LEFT. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

View northeast of mould loft and plating cutting shop in ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View northeast of mould loft and plating cutting shop in structural assembly shop (building no. 541) - Naval Base Philadelphia-Philadelphia Naval Shipyard, Structural Assembly Shop, League Island, Philadelphia, Philadelphia County, PA

45. SOUTHERN INTERIOR VIEW OF MOULD CONDITIONING BUILDING SHOWING FINK ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

45. SOUTHERN INTERIOR VIEW OF MOULD CONDITIONING BUILDING SHOWING FINK TRUSSES AND CORRUGATED METAL SHEETING. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Shear Strength of Remoulding Clay Samples Using Different Methods of Moulding

NASA Astrophysics Data System (ADS)

Norhaliza, W.; Ismail, B.; Azhar, A. T. S.; Nurul, N. J.

2016-07-01

Shear strength for clay soil was required to determine the soil stability. Clay was known as a soil with complex natural formations and very difficult to obtain undisturbed samples at the site. The aim of this paper was to determine the unconfined shear strength of remoulded clay on different methods in moulding samples which were proctor compaction, hand operated soil compacter and miniature mould methods. All the samples were remoulded with the same optimum moisture content (OMC) and density that were 18% and 1880 kg/m3 respectively. The unconfined shear strength results of remoulding clay soils for proctor compaction method was 289.56kPa with the strain 4.8%, hand operated method was 261.66kPa with the strain 4.4% and miniature mould method was 247.52kPa with the strain 3.9%. Based on the proctor compaction method, the reduction percentage of unconfined shear strength of remoulded clay soil of hand operated method was 9.66%, and for miniature mould method was 14.52%. Thus, because there was no significant difference of reduction percentage of unconfined shear strength between three different methods, so it can be concluded that remoulding clay by hand operated method and miniature mould method were accepted and suggested to perform remoulding clay samples by other future researcher. However for comparison, the hand operated method was more suitable to form remoulded clay sample in term of easiness, saving time and less energy for unconfined shear strength determination purposes.

Compostability and biodegradation study of PLA-wheat straw and PLA-soy straw based green composites in simulated composting bioreactor.

PubMed

Pradhan, Ranjan; Misra, Manjusri; Erickson, Larry; Mohanty, Amar

2010-11-01

A laboratory scale simulated composting facility (as per ASTM D 5338) was designed and utilized to determine and evaluate the extent of degradation of polylactic acid (PLA), untreated wheat and soy straw and injection moulded composites of PLA-wheat straw (70:30) and PLA-soy straw (70:30). The outcomes of the study revealed the suitability of the test protocol, validity of the test system and defined the compostability of the composites of PLA with unmodified natural substrate. The study would help to design composites using modified soy straw and wheat straw as reinforcement/filler to satisfy ASTM D 6400 specifications. Copyright 2010 Elsevier Ltd. All rights reserved.

The taphonomy of unmineralised Palaeozoic fossils preserved as siliciclastic moulds and casts, and their utility in assessing the interaction between environmental change and the fossil record

NASA Astrophysics Data System (ADS)

MacGabhann, Breandán; Schiffbauer, James; Hagadorn, James; Van Roy, Peter; Lynch, Edward; Morrsion, Liam; Murray, John

2015-04-01

The enhanced preservation potential of biomineralised tissues in fossil organisms is a key factor in their utility in the investigation of palaeoenvironmental change on fossil ecosystems. By contrast, the considerably lower preservation potential of entirely unmineralised organisms severely reduces the utility of their temporal and spatial distribution in such analyses. However, understanding the taphonomic processes which lead to the preservation of such soft-bodied fossils may be an under-appreciated source of information, particularly in the case of specimens preserved as moulds and casts in coarser siliciclastic sediments. This information potential is well demonstrated by fossil eldonids, a Cambrian to Devonian clade of unmineralised asymmetrical discoidal basal or stem deuterostomes, with an apparently conservative biology and no clear palaeoenvironmental or biogeographical controls on their distribution. We investigated the taphonomic processes involved in the preservation of fossil eldonids as moulds and casts on bedding surfaces and within event beds from sandstones of the Ordovician Tafilalt lagerstätte in south-eastern Morocco, and from siltstones of the Devonian West Falls Group of New York, USA. Laser Raman microspectroscopy, SEM BSE imaging and EDS elemental mapping of fossil specimens reveals that moulded biological surfaces are coated by a fossil surface veneer primarily consisting of mixed iron oxides and oxyhydroxides (including pseudomorphs after pyrite), and aluminosilicate clay minerals. Moreover, comparison to fossil eldonids preserved as carbonaceous compressions in the Burgess Shale reveals that the biological structures preserved in the Tafilalt and New York specimens - the dorsal surface and a coiled sac containing the digestive tract - represent only specific portions of the anatomy of the complete animal. We suggest that the preserved remains were the only parts of these eldonid organisms composed primarily of complex organic biopolymers, and that these tissues were preferentially fossilised by the formation of an early diagenic mould directly on the organic surfaces. Excess divalent iron ions, produced during decay of more labile tissues by means of bacterial iron reduction, would have adsorbed to anionic functional groups in the biopolymeric tissues. This would have provided a ready substrate for the formation and growth of such an early diagenic mineralised mould, including aluminosilicate minerals produced via reaction with seawater silica and metal ions, and iron sulphide minerals produced via reaction with hydrogen sulphide and free sulphur produced from seawater sulphate through bacterial sulphate reduction associated with further decay. Subsequent weathering would have oxidised such iron sulphides to oxides and oxyhydroxides. This taphonomic model supports the lack of utility of the eldonid palaeobiological record in analysing environmental influence on biological communities, due to the lack of preservation of key anatomical components. However, it also suggests that the very occurrence of fossils preserved in this style is dependent on extrinsic palaeoenvironmental factors - including pH, Eh, and the concentration of other ions in the contemporaneous seawater. Analyses of the distribution of fossils preserved in this style may therefore provide information on ambient conditions which may have affected the distribution of contemporaneous mineralised fossils, potentially allowing a more complete analysis of the effects of palaeoenvironmental change on fossil ecosystems.

Inclusion behaviour in the liquid core during continuous casting

NASA Astrophysics Data System (ADS)

Jiang, Guang S.

Water models using perspex have been built to study the fluid flow and recirculation patterns developed in the sump of a steel continuous casting machine and the influences these have on the behaviour of inclusions. An experimental method has been devised to simulate the behaviour of inclusions in the sump and to study the apportionment of the input flux of inclusions between the molten mould powder layer and the strand. The method entails the uses of finely dispersed coloured paraffin oil in the inlet stream together with a floating colourless paraffin layer on the top of the water in the model mould to simulate the molten powder layer on top of the molten steel.A theoretical model has been formulated which relates the inclusion separation in the sump to the fluid flow there. The inclusion removal ratio in the sump for a given continuous casting machine can be predicted using this theoretical model. The model, using the properties of liquid steel and practicable casting speeds, demonstrates that the removal of inclusions of small size (<40 um) from the mould sump is less than 5% efficient.Inclusion agglomeration plays an important role in inclusion removal. It has been shown that deep submersion of the SEN enhances the agglomeration of inclusion particle. Under certain conditions, for example, the average particle diameter in the meniscus region has been found to be as much as three times its value at the SEN nozzle.The use of fine alumina flakes or small air bubbles, together with a plane light source, has been found to be very successful in studying the fluid flow patterns developed in three-dimensional models. Employing this method, the fluid flow patterns developed on different planes within the model mould have been viewed and recorded photographically. The photographs so obtained have helped to explain the results obtained for the removal of inclusions. The fluid flow patterns developed when small outside diameter nozzles with deep SEN submerged depths are used have been found to be of benefit to the removal of inclusions.Increasing the SEN submerged depth promotes inclusion agglomeration and hence increases the inclusion removal ratio. Reducing the nozzle outside diameter and the casting speed increases the inclusion removal ratio in the sump. But the infleunces of these latter changes are not very strong, so that inclusion removal consideration need not influence the design strategies used for the casting speed and nozzle outside diameter. The SEN port angle has a little effect on the inclusion removal when using deep SEN submerged depth.Although argon stream introduced into the tundish nozzle stream can protect the nozzle blockage, it is not beneficial to the inclusion removal in the sump.

Mycotoxins in Meat and Processed Meat Products

NASA Astrophysics Data System (ADS)

Bailly, Jean-Denis; Guerre, Philippe

Mycotoxins are toxic substances elaborated by fungi. They constitute a heterogeneous group of secondary metabolites with diverse potent pharmacological and toxic effects in humans and animals. More than 300 secondary metabolites have been identified but around 30 are of real concern for human and animal health (for review, see Bennett & Klich, 2003). These molecules are produced during mould development on plants in the field or during storage period. They can be found as natural contaminants of many vegetal foods or feeds, mainly cereals, but also fruits, nuts, grains, forage as well as compound foods intended for human or animal consumption. Most important mycotoxins are produced by moulds belonging to Aspergillus, Penicillium and Fusarium genus (Bhatnagar, Yu, & Ehrlich, 2002; Conkova, Laciakova, Kovac, & Seidel, 2003; Pitt, 2002). These molecules are usually classified depending on the fungal species that produce them (Table 4.1)

Ultrasound-based measurement of liquid-layer thickness: A novel time-domain approach

NASA Astrophysics Data System (ADS)

Praher, Bernhard; Steinbichler, Georg

2017-01-01

Measuring the thickness of a thin liquid layer between two solid materials is important when the adequate separation of metallic parts by a lubricant film (e.g., in bearings or mechanical seals) is to be assessed. The challenge in using ultrasound-based systems for such measurements is that the signal from the liquid layer is a superposition of multiple reflections. We have developed an algorithm for reconstructing this superimposed signal in the time domain. By comparing simulated and measured signals, the time-of-flight of the ultrasonic pulse in a layer can be estimated. With the longitudinal sound velocity known, the layer thickness can then be calculated. In laboratory measurements, we validate successfully (maximum relative error 4.9%) our algorithm for layer thicknesses ranging from 30 μm to 200 μm. Furthermore, we tested our method in the high-temperature environment of polymer processing by measuring the clearance between screw and barrel in the plasticisation unit of an injection moulding machine. The results of such measurements can indicate (i) the wear status of the tribo-mechanical screw-barrel system and (ii) unsuitable process conditions.

Facial asymmetry correction with moulded helmet therapy in infants with deformational skull base plagiocephaly.

PubMed

Kreutz, Matthias; Fitze, Brigitte; Blecher, Christoph; Marcello, Augello; Simon, Ruben; Cremer, Rebecca; Zeilhofer, Hans-Florian; Kunz, Christoph; Mayr, Johannes

2018-01-01

The recommendation issued by the American Academy of Pediatrics in the early 1990s to position infants on their back during sleep to prevent sudden infant death syndrome (SIDS) has dramatically reduced the number of deaths due to SIDS but has also markedly increased the prevalence of positional skull deformation in infants. Deformation of the base of the skull occurs predominantly in very severe deformational plagiocephaly and is accompanied by facial asymmetry, as well as an altered ear position, called ear shift. Moulded helmet therapy has become an accepted treatment strategy for infants with deformational plagiocephaly. The aim of this study was to determine whether facial asymmetry could be corrected by moulded helmet therapy. In this retrospective, single-centre study, we analysed facial asymmetry of 71 infants with severe deformational plagiocephaly with or without deformational brachycephaly who were undergoing moulded helmet therapy between 2009 and 2013. Computer-assisted, three-dimensional, soft-tissue photographic scanning was used to record the head shape before and after moulded helmet therapy. The distance between two landmarks in the midline of the face (i.e., root of the nose and nasal septum) and the right and left tragus were measured on computer-generated indirect and objective 3D photogrammetry images. A quotient was calculated between the two right- and left-sided distances to the midline. Quotients were compared before and after moulded helmet therapy. Infants without any therapy served as a control group. The median age of the infants before onset of moulded helmet therapy was 5 months (range 3-16 months). The median duration of moulded helmet therapy was 5 months (range 1-16 months). Comparison of the pre- and post-treatment quotients of the left vs. right distances measured between the tragus and root of the nose (n = 71) and nasal septum (n = 71) revealed a significant reduction of the asymmetry (Tragus-Nasion-Line Quotient: 0.045-0.022; p < 0.0001; Tragus-Subnasale-Line Quotient: 0.045-0.021; p < 0.0001). The control group without treatment showed no significant change in the quotient (Tragus-Nasion-Line Quotient no helmet: 0.049-0.055/Tragus-Subnasale-Line Quotient no helmet: 0.039-0.055). Moulded helmet therapy can correct facial symmetry in infants with deformational plagiocephaly and associated facial and basal skull asymmetry. Copyright © 2017 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Effect of Na2O on Crystallisation Behaviour and Heat Transfer of Fluorine-Free Mould Fluxes

NASA Astrophysics Data System (ADS)

Yang, Jian; Zhang, Jianqiang; Sasaki, Yasushi; Ostrovski, Oleg; Zhang, Chen; Cai, Dexiang; Kashiwaya, Yoshiaki

Most of the commercial mould fluxes contain fluorides which bring about serious environmental problems. The major challenge in the application of fluorine-free mould fluxes is to control the heat transfer from the strand to copper mould which is closely related to crystallisation behaviour. In this study, the effects of Na2O on the crystallisation behaviour and heat transfer of CaO-SiO2-Na2O-B2O3-TiO2-Al2O3-MgO-Li2O mould fluxes were investigated using single /double hot thermocouple technique (SHTT/DHTT) and infrared emitter technique (IET), respectively. Continuous cooling transformation (CCT) and time-temperature transformation (TTT) diagrams constructed using SHTT showed that the increase of Na2O concentration led to higher critical cooling rate and shorter incubation time. The crystallisation behaviour in a thermal gradient was examined using DHTT. The heat flux measured by IET showed that the increase of Na2O concentration decreased the heat flux when Na2O was lower than 9 mass% but the further increase of Na2O raised the heat flux. The relationship between flux crystallisation and heat transfer was also discussed.

Microstructure and thermomechanical properties relationship of segmented thermoplastic polyurethane (TPU)

NASA Astrophysics Data System (ADS)

Frick, Achim; Borm, Michael; Kaoud, Nouran; Kolodziej, Jan; Neudeck, Jens

2014-05-01

Thermoplastic polyurethanes (TPU) are important polymeric materials for seals. In competition with Acrylonitrile butadiene rubbers (NBR), TPU exhibits higher strength and a considerable better abrasion resistance. The advantage of NBR over TPU is a smaller compression set but however TPU excels in its much shorter processing cycle times. Generally a TPU is a block copolymer composed of hard and soft segments, which plays an important role in determining the material properties. TPU can be processed either to ready moulded parts or can be incorporated by multi component moulding, in both cases it shows decent mechanical properties. In the present work, the relationship between melt-process induced TPU morphology and resultant thermo mechanical properties were examined and determined by means of quasi-static tensile test, creep experiment, tension test and dynamical mechanical analysis (DMA). Scanning electron beam microscope (SEM) and differential scanning calorimeter (DSC) were used to study the morphology of the samples. A significant mathematical description of the stress-strain behaviour of TPU was found using a 3 term approach. Moreover it became evident that processing conditions such as processing temperature have crucial influence on morphology as well as short and long-term performance. To be more precise, samples processed at higher temperatures showed a lack of large hard segment agglomerates, a smaller strength for strains up to 250% and higher creep compliance.

Fungi and bacteria in mould-damaged and non-damaged office environments in a subarctic climate

NASA Astrophysics Data System (ADS)

Salonen, Heidi; Lappalainen, Sanna; Lindroos, Outi; Harju, Riitta; Reijula, Kari

The fungi and bacterial levels of the indoor air environments of 77 office buildings were measured in winter and a comparison was made between the buildings with microbe sources in their structures and those without such sources. Penicillium, yeasts, Cladosporium and non-sporing isolates were the commonest fungi detected in the indoor air and in settled dust, in both the mould-damaged and control buildings. Aspergillus ochraceus, Aspergillus glaucus and Stachybotrys chartarium were found only in environmental samples from the mould-damaged buildings. Some other fungi, with growth requiring of water activity, aw, above 0.85, occurred in both the reference and mould-damaged buildings, but such fungi were commoner in the latter type of buildings. The airborne concentrations of Penicillium, Aspergillus versicolor and yeasts were the best indicators of mould damage in the buildings studied. Penicillium species and A. versicolor were also the most abundant fungi in the material samples. This study showed that the fungi concentrations were very low (2-45 cfu m -3 90% of the concentrations being <15 cfu m -3) in the indoor air of the normal office buildings. Although the concentration range of airborne fungi was wider for the mould-damaged buildings (2-2470 cfu m -3), only about 20% of the samples exceeded 100 cfu m -3. The concentrations of airborne bacteria ranged from 12 to 540 cfu m -3 in the control buildings and from 14 to 1550 cfu m -3 in the mould-damaged buildings. A statistical analysis of the results indicated that bacteria levels are generally <600 cfu m -3 in office buildings in winter and fungi levels are <50 cfu m -3. These normal levels are applicable to subarctic climates for urban, modern office buildings when measurements are made using a six-stage impactor. These levels should not be used in evaluations of health risks, but elevated levels may indicate the presence of abnormal microbe sources in indoor air and a need for additional environmental investigations.

Mould routine identification in the clinical laboratory by matrix-assisted laser desorption ionization time-of-flight mass spectrometry.

PubMed

Cassagne, Carole; Ranque, Stéphane; Normand, Anne-Cécile; Fourquet, Patrick; Thiebault, Sandrine; Planard, Chantal; Hendrickx, Marijke; Piarroux, Renaud

2011-01-01

MALDI-TOF MS recently emerged as a valuable identification tool for bacteria and yeasts and revolutionized the daily clinical laboratory routine. But it has not been established for routine mould identification. This study aimed to validate a standardized procedure for MALDI-TOF MS-based mould identification in clinical laboratory. First, pre-extraction and extraction procedures were optimized. With this standardized procedure, a 143 mould strains reference spectra library was built. Then, the mould isolates cultured from sequential clinical samples were prospectively subjected to this MALDI-TOF MS based-identification assay. MALDI-TOF MS-based identification was considered correct if it was concordant with the phenotypic identification; otherwise, the gold standard was DNA sequence comparison-based identification. The optimized procedure comprised a culture on sabouraud-gentamicin-chloramphenicol agar followed by a chemical extraction of the fungal colonies with formic acid and acetonitril. The identification was done using a reference database built with references from at least four culture replicates. For five months, 197 clinical isolates were analyzed; 20 were excluded because they were not identified at the species level. MALDI-TOF MS-based approach correctly identified 87% (154/177) of the isolates analyzed in a routine clinical laboratory activity. It failed in 12% (21/177), whose species were not represented in the reference library. MALDI-TOF MS-based identification was correct in 154 out of the remaining 156 isolates. One Beauveria bassiana was not identified and one Rhizopus oryzae was misidentified as Mucor circinelloides. This work's seminal finding is that a standardized procedure can also be used for MALDI-TOF MS-based identification of a wide array of clinically relevant mould species. It thus makes it possible to identify moulds in the routine clinical laboratory setting and opens new avenues for the development of an integrated MALDI-TOF MS-based solution for the identification of any clinically relevant microorganism.

Manufacture and mechanical characterisation of high voltage insulation for superconducting busbars - (Part 1) Materials selection and development

NASA Astrophysics Data System (ADS)

Clayton, N.; Crouchen, M.; Devred, A.; Evans, D.; Gung, C.-Y.; Lathwell, I.

2017-04-01

It is planned that the high voltage electrical insulation on the ITER feeder busbars will consist of interleaved layers of epoxy resin pre-impregnated glass tapes ('pre-preg') and polyimide. In addition to its electrical insulation function, the busbar insulation must have adequate mechanical properties to sustain the loads imposed on it during ITER magnet operation. This paper reports an investigation into suitable materials to manufacture the high voltage insulation for the ITER superconducting busbars and pipework. An R&D programme was undertaken in order to identify suitable pre-preg and polyimide materials from a range of suppliers. Pre-preg materials were obtained from 3 suppliers and used with Kapton HN, to make mouldings using the desired insulation architecture. Two main processing routes for pre-pregs have been investigated, namely vacuum bag processing (out of autoclave processing) and processing using a material with a high coefficient of thermal expansion (silicone rubber), to apply the compaction pressure on the insulation. Insulation should have adequate mechanical properties to cope with the stresses induced by the operating environment and a low void content necessary in a high voltage application. The quality of the mouldings was assessed by mechanical testing at 77 K and by the measurement of the void content.

43. NORTHEASTERN VIEW OF MOULD CONDITIONING BUILDING AND BOP SHOP, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

43. NORTHEASTERN VIEW OF MOULD CONDITIONING BUILDING AND BOP SHOP, WITH OPEN HEARTH No. 2 BUILDING ON LEFT. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Bio-prospecting of distillery yeasts as bio-control and bio-remediation agents.

PubMed

Ubeda, Juan F; Maldonado, María; Briones, Ana I; Francisco, J Fernández; González, Francisco J

2014-05-01

This work constitutes a preliminary study in which the capacity of non-Saccharomyces yeasts isolated from ancient distilleries as bio-control agents against moulds and in the treatment of waste waters contaminated by heavy metals-i.e. bio-remediation-is shown. In the first control assays, antagonist effect between non-Saccharomyces yeasts, their extracts and supernatants against some moulds, analysing the plausible (not exhaustive) involved factors were qualitatively verified. In addition, two enzymatic degrading properties of cell wall plant polymers, quitinolitic and pectinolitic, were screened. Finally, their use as agents of bio-remediation of three heavy metals (cadmium, chromium and lead) was analysed semi-quantitatively. The results showed that all isolates belonging to Pichia species effectively inhibited all moulds assayed. Moreover, P. kudriavzevii is a good candidate for both bio-control and bio-remediation because it inhibited moulds and accumulated the major proportion of the three tested metals.

A biologically inspired network design model.

PubMed

Zhang, Xiaoge; Adamatzky, Andrew; Chan, Felix T S; Deng, Yong; Yang, Hai; Yang, Xin-She; Tsompanas, Michail-Antisthenis I; Sirakoulis, Georgios Ch; Mahadevan, Sankaran

2015-06-04

A network design problem is to select a subset of links in a transport network that satisfy passengers or cargo transportation demands while minimizing the overall costs of the transportation. We propose a mathematical model of the foraging behaviour of slime mould P. polycephalum to solve the network design problem and construct optimal transport networks. In our algorithm, a traffic flow between any two cities is estimated using a gravity model. The flow is imitated by the model of the slime mould. The algorithm model converges to a steady state, which represents a solution of the problem. We validate our approach on examples of major transport networks in Mexico and China. By comparing networks developed in our approach with the man-made highways, networks developed by the slime mould, and a cellular automata model inspired by slime mould, we demonstrate the flexibility and efficiency of our approach.

A Biologically Inspired Network Design Model

PubMed Central

Zhang, Xiaoge; Adamatzky, Andrew; Chan, Felix T.S.; Deng, Yong; Yang, Hai; Yang, Xin-She; Tsompanas, Michail-Antisthenis I.; Sirakoulis, Georgios Ch.; Mahadevan, Sankaran

2015-01-01

A network design problem is to select a subset of links in a transport network that satisfy passengers or cargo transportation demands while minimizing the overall costs of the transportation. We propose a mathematical model of the foraging behaviour of slime mould P. polycephalum to solve the network design problem and construct optimal transport networks. In our algorithm, a traffic flow between any two cities is estimated using a gravity model. The flow is imitated by the model of the slime mould. The algorithm model converges to a steady state, which represents a solution of the problem. We validate our approach on examples of major transport networks in Mexico and China. By comparing networks developed in our approach with the man-made highways, networks developed by the slime mould, and a cellular automata model inspired by slime mould, we demonstrate the flexibility and efficiency of our approach. PMID:26041508

Characterization and control of thread mould in cheese.

PubMed

Basílico, J C; debasílico, M Z; Chiericatti, C; Vinderola, C G

2001-06-01

The origin of a mould responsible for the contamination of an Argentinian cheese factory was identified and several antifungal treatments were assessed. Moulds were isolated and identified from vacuum-packed hard cheeses, from the environment and from the surfaces of the factory. A suspension conidia test containing different fungicides was performed; another assay involved the fumigation with p-OH fenilsalicidamide. Only Phoma glomerata was found in all of the mouldy cheeses, and was also obtained from different environments and machine surfaces. The most effective treatments against P. glomerata isolates were 0.5% (w/v) natamycin and 2% (v/v) parabens. Fumigation with p-OH fenilsalicidamide showed no satisfactory results. P. glomerata is an important thread mould-contaminating agent in vacuum-packed hard cheeses. Taking into account the survival of the conidia of the P. glomerata isolates to different antifungal treatments, the sources of contamination need to be controlled by designing a good factory layout.

From the patient to the clinical mycology laboratory: how can we optimise microscopy and culture methods for mould identification?

PubMed

Vyzantiadis, Timoleon-Achilleas A; Johnson, Elizabeth M; Kibbler, Christopher C

2012-06-01

The identification of fungi relies mainly on morphological criteria. However, there is a need for robust and definitive phenotypic identification procedures in order to evaluate continuously evolving molecular methods. For the future, there is an emerging consensus that a combined (phenotypic and molecular) approach is more powerful for fungal identification, especially for moulds. Most of the procedures used for phenotypic identification are based on experience rather than comparative studies of effectiveness or performance and there is a need for standardisation among mycology laboratories. This review summarises and evaluates the evidence for the major existing phenotypic identification procedures for the predominant causes of opportunistic mould infection. We have concentrated mainly on Aspergillus, Fusarium and mucoraceous mould species, as these are the most important clinically and the ones for which there are the most molecular taxonomic data.

Normalization in Lie algebras via mould calculus and applications

NASA Astrophysics Data System (ADS)

Paul, Thierry; Sauzin, David

2017-11-01

We establish Écalle's mould calculus in an abstract Lie-theoretic setting and use it to solve a normalization problem, which covers several formal normal form problems in the theory of dynamical systems. The mould formalism allows us to reduce the Lie-theoretic problem to a mould equation, the solutions of which are remarkably explicit and can be fully described by means of a gauge transformation group. The dynamical applications include the construction of Poincaré-Dulac formal normal forms for a vector field around an equilibrium point, a formal infinite-order multiphase averaging procedure for vector fields with fast angular variables (Hamiltonian or not), or the construction of Birkhoff normal forms both in classical and quantum situations. As a by-product we obtain, in the case of harmonic oscillators, the convergence of the quantum Birkhoff form to the classical one, without any Diophantine hypothesis on the frequencies of the unperturbed Hamiltonians.

Computational modelling of a thermoforming process for thermoplastic starch

NASA Astrophysics Data System (ADS)

Szegda, D.; Song, J.; Warby, M. K.; Whiteman, J. R.

2007-05-01

Plastic packaging waste currently forms a significant part of municipal solid waste and as such is causing increasing environmental concerns. Such packaging is largely non-biodegradable and is particularly difficult to recycle or to reuse due to its complex composition. Apart from limited recycling of some easily identifiable packaging wastes, such as bottles, most packaging waste ends up in landfill sites. In recent years, in an attempt to address this problem in the case of plastic packaging, the development of packaging materials from renewable plant resources has received increasing attention and a wide range of bioplastic materials based on starch are now available. Environmentally these bioplastic materials also reduce reliance on oil resources and have the advantage that they are biodegradable and can be composted upon disposal to reduce the environmental impact. Many food packaging containers are produced by thermoforming processes in which thin sheets are inflated under pressure into moulds to produce the required thin wall structures. Hitherto these thin sheets have almost exclusively been made of oil-based polymers and it is for these that computational models of thermoforming processes have been developed. Recently, in the context of bioplastics, commercial thermoplastic starch sheet materials have been developed. The behaviour of such materials is influenced both by temperature and, because of the inherent hydrophilic characteristics of the materials, by moisture content. Both of these aspects affect the behaviour of bioplastic sheets during the thermoforming process. This paper describes experimental work and work on the computational modelling of thermoforming processes for thermoplastic starch sheets in an attempt to address the combined effects of temperature and moisture content. After a discussion of the background of packaging and biomaterials, a mathematical model for the deformation of a membrane into a mould is presented, together with its finite element discretisation. This model depends on material parameters of the thermoplastic and details of tests undertaken to determine these and the results produced are given. Finally the computational model is applied for a thin sheet of commercially available thermoplastic starch material which is thermoformed into a specific mould. Numerical results of thickness and shape for this problem are given.

Impact of board-marker accuracy on lumber yield

Treesearch

Urs Buehlmann; R. Edward Thomas

2003-01-01

The production of wooden furniture parts, mouldings, and flooring requires the removal of unacceptable character marks (also called "defects") such as holes, rot, knots, etc., from boards. The majority of the wood processing industry manually identifies such unusable areas and marks them with fluorescent crayons. Automated saws scan these marks and computers...

Heritage Languages at Upper Secondary Level in South Australia: A Struggle for Legitimacy

ERIC Educational Resources Information Center

Mercurio, Antonio; Scarino, Angela

2005-01-01

This paper describes how more than 40 languages gained and retained legitimacy as subjects for graduation from upper secondary schooling and for tertiary entrance selection in the South Australian educational system. Essentially the process required conforming with administrative, curriculum and community structures and fitting the mould of…

Eye Movements Reveal How Task Difficulty Moulds Visual Search

ERIC Educational Resources Information Center

Young, Angela H.; Hulleman, Johan

2013-01-01

In two experiments we investigated the relationship between eye movements and performance in visual search tasks of varying difficulty. Experiment 1 provided evidence that a single process is used for search among static and moving items. Moreover, we estimated the functional visual field (FVF) from the gaze coordinates and found that its size…

Window encapsulation in car industry by using the 50 {Omega} RF technology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernard, J.P.; Barboteau, M.; Collet, L.

Throughout the world car industry has been using window encapsulation for a few years now. This technology is mainly used in production lines and is called RIM for polyurethane reaction injection moulding. This technology, however brings about some problems such as: glass breaking during mould closure, high production cost, systematic rough edges. The PSA Group (Peugeot-Citroen), a pioneer in this field, in collaboration with SAIREM has launched a new innovating process for window encapsulation by using the 50 {Omega} RF technology for gelling PVC Plastisol. The study was followed by an industrial prototype. Industrial equipment was then installed at WEBASTOmore » HEULIEZ for window encapsulation of the sunshine roof for the Citroen Xantia. The authors describe the principle of window encapsulation and the different existing processes. They describe the 50 {Omega} RF technology, an industrial installation and the constraints of this technology in order to get maximum efficiency. In the conclusion they present a technical and economical analysis of the different solutions for window encapsulation. They also present the advantages of the 50 {Omega} RF technology and the new opportunities it offers.« less

Laser welding process in PP moulding parts: Evaluation of seam performance

NASA Astrophysics Data System (ADS)

Oliveira, N.; Pontes, A. J.

2015-12-01

The Polypropylene is one of the most versatile polymer materials used in the industry. Due to this versatility, it is possible to use it in different products. This material can also be mixed with several additives namely glass fiber, carbon nanotubes, etc. This compatibility with different additives allows also obtaining products with characteristics that goes from an impact absorber to an electricity conductor. When is necessary to join components in PP they could be welded through hot plate, ultrasonic weld and also by laser. This study had the objective of study the influence of several variables, capable of influence the final quality of the seam. In this case were studied variables of the injection molding process as mold temperature and cooling time. Was also studied laser welding variables and different materials. The results showed that the variables that have the most influence were mould temperature, laser velocity and laser diameter. The seams were analyzed using Optical Microscopy technique. The seams showed perfect contact between the materials analyzed, despite the high standard variation presented in the mechanical testes.

Mould and yeast flora in fresh berries, grapes and citrus fruits.

PubMed

Tournas, V H; Katsoudas, Eugenia

2005-11-15

Fresh fruits are prone to fungal contamination in the field, during harvest, transport, marketing, and with the consumer. It is important to identify fungal contaminants in fresh fruits because some moulds can grow and produce mycotoxins on these commodities while certain yeasts and moulds can cause infections or allergies. In this study, 251 fresh fruit samples including several varieties of grapes, strawberries, blueberries, raspberries, blackberries, and various citrus fruits were surface-disinfected, incubated at room temperature for up to 14 days without supplemental media, and subsequently examined for mould and yeast growth. The level of contamination (percent of contaminated items/sample) varied depending on the type of fruit. All raspberry and blackberry samples were contaminated at levels ranging from 33% to 100%, whereas 95% of the blueberry samples supported mould growth at levels between 10% and 100% of the tested berries, and 97% of strawberry samples showed fungal growth on 33-100% of tested berries. The most common moulds isolated from these commodities were Botrytis cinerea, Rhizopus (in strawberries), Alternaria, Penicillium, Cladosporium and Fusarium followed by yeasts, Trichoderma and Aureobasidium. Thirty-five percent of the grape samples tested were contaminated and supported fungal growth; the levels of contamination ranged from 9% to 80%. The most common fungi spoiling grapes were Alternaria, B. cinerea and Cladosporium. Eighty-three percent of the citrus fruit samples showed fungal growth at levels ranging from 25% to 100% of tested fruits. The most common fungi in citrus fruits were Alternaria, Cladosporium, Penicillium, Fusarium and yeasts. Less common were Trichoderma, Geotrichum and Rhizopus.

10. DETAIL OF CORNICE MOULDING WITH RAM'S HEAD MOTIF. EIGHT ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

10. DETAIL OF CORNICE MOULDING WITH RAM'S HEAD MOTIF. EIGHT SHADES OF GOLD LEAF AND BURNISHED GOLD LEAF WERE USED FOR THE INTERIOR FINISHES - Anaconda Historic District, Washoe Theater, 305 Main Street, Anaconda, Deer Lodge County, MT

DETAIL OF CORNICE MOULDING WITH RAM'S HEAD MOTIF. EIGHT SHADES ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF CORNICE MOULDING WITH RAM'S HEAD MOTIF. EIGHT SHADES OF GOLD LEAF AND BURNISHED GOLD LEAF WERE USED FOR THE INTERIOR FINISHES. - Anaconda Historic District, Washoe Theater, 305 Main Street, Anaconda, Deer Lodge County, MT

Quality assessment for brick making of the bleached topsoil of Vertic Planosols in the south-western Ethiopian Highlands

NASA Astrophysics Data System (ADS)

Dumon, Mathijs; Vandemeulebroeke, Laure; Van Daele, Kim; Regassa Tolossa, Alemayehu; Proost, Vicky; Van Ranst, Eric

2013-04-01

Planosols are a very common soil type in Ethiopia. The Vertic Planosols of the south-western Highlands are typical examples of duplex soils, characterized by a bleached, silty top horizon abruptly overlying a heavy clay subsoil. The bleached topsoil material is of local economic importance as it is extensively used for brick making. The aim of this research was to assess the quality of locally produced bricks following Ethiopian and European quality standards, and formulating recommendations to improve the quality of the bricks. After a reconnaissance field survey three brick production sites, Bore, Serbo and Marawaa, were selected. At each site the bleached topsoil was sampled for physico-chemical analyses and locally produced bricks were collected for further testing. The production process, documented by interviewing locals, consists of excavating the bleached topsoil, manual mixing with water, shaping using an ash-covered wooden mould, trimming using an iron wire, and drying in open air. About 30,000 dried bricks are then piled up to form a rectangular field-oven and fired for about two and a half days. It was observed and admitted by the locals that about 10% of the produced bricks are lost due to severe cracking and/or melting on the inside of the field oven. On the other hand, some of the bricks on the outside of the field oven were not sufficiently fired. Physico-chemical (texture, total elemental chemical composition, carbonate content, total carbon content, sulphur content, cation exchange capacity, total specific surface) and mineralogical (XRD, DSC, thermogravimetry, dilatometry, optical microscopy) analyses were carried out. Additionally, the locally produced bricks were physically characterised by their dimensions, initial rate of water absorption (IRWA), water absorption after 24h and compressive strength. Based on the observed properties for the soil material and the locally produced bricks, mixtures of soil samples and a sand additive were made in an attempt to improve the quality of the bricks. In addition, the effect of the moulding method was taken into account by making both hand-moulded and pressure-moulded bricks from both the reference soil material and the improved mixture. These new bricks were also tested on water absorption, drying, firing and total shrinkage and compressive strength. The analytical results indicated the locally produced bricks are quite strong, but absorb too much water when matched with European and Ethiopian standards. New bricks made from the improved mixtures show a significantly lower water absorption. Compressive strength on the other hand, is slightly reduced for these test units, but still above standard levels. A lower variability in measured values when using pressure-moulded test units compared to hand-moulded test units indicated the former result in a more uniform quality of bricks. It can be concluded that the current locally applied methods and materials produce a moderate quality brick on average, with large variation in the quality. Use of a sandy additive, adjusting the moulding method and improving the field oven layout to achieve a more homogeneous temperature distribution, are surely options to improve the quality of the bricks produced from these bleached materials.

Replication of self-centering optical fiber alignment structures using hot embossing

NASA Astrophysics Data System (ADS)

Ebraert, Evert; Wissmann, Markus; Barié, Nicole; Guttmann, Markus; Schneider, Marc; Kolew, Alexander; Worgull, Matthias; Beri, Stefano; Watté, Jan; Thienpont, Hugo; Van Erps, Jürgen

2016-04-01

With the demand for broadband connectivity on the rise due to various services like video-on-demand and cloud computing becoming more popular, the need for better connectivity infrastructure is high. The only future- proof option to supply this infrastructure is to deploy "fiber to the home" (FTTH) networks. One of the main difficulties with the deployment of FTTH is the vast amount of single-mode fiber (SMF) connections that need to be made. Hence there is a strong need for components which enable high performance, robust and easy-to- use SMF connectors. Since large-scale deployment is the goal, these components should be mass-producible at low cost. We discuss a rapid prototyping process on the basis of hot embossing replication of a self-centering alignment system (SCAS) based on three micro-springs, which can position a SMF independently of its diameter. This is beneficial since there is a fabrication tolerance of up to +/-1 μm on a standard G.652 SMF's diameter that can lead to losses if the outer diameter is used as a reference for alignment. The SCAS is first prototyped with deep proton writing (DPW) in polymethylmethacrylate (PMMA) after which it is glued to a copper substrate with an adhesive. Using an electroforming process, a nickel block is grown over the PMMA prototype followed by mechanical finishing to fabricate a structured nickel mould insert. Even though the mould insert shows non- ideal and rounded features it is used to create PMMA replicas of the SCAS by means of hot embossing. The SCAS possesses a central opening in which a bare SMF can be clamped, which is designed with a diameter of 121 μm. PMMA replicas are dimensionally characterized using a multisensor coordinate measurement machine and show a central opening diameter of 128.3 +/- 2.8 μm. This should be compared to the central opening diameter of the DPW prototype used for mould formation which was measured to be 120.5 μm. This shows that the electroforming and subsequent replication process is possible for complex micro-scale components and could be accurate after optimisation. We characterized the sidewall roughness of PMMA replicas using a non- contact optical profiler, resulting in a root-mean-square roughness of 48 nm over an area of 63.7 μm×47.8 μm. This low sidewall roughness is especially important in the replication of high aspect ratio structures to facilitate demoulding since the sidewalls cause the most friction with the mould insert.

Replication fidelity assessment of large area sub-μm structured polymer surfaces using scatterometry

NASA Astrophysics Data System (ADS)

Calaon, M.; Madsen, M. H.; Weirich, J.; Hansen, H. N.; Tosello, G.; Hansen, P. E.; Garnaes, J.; Tang, P. T.

2015-12-01

The present study addresses one of the key challenges in the product quality control of transparent structured polymer substrates, the replication fidelity of sub-μm structures over a large area. Additionally the work contributes to the development of new techniques focused on in-line characterization of large nanostructured surfaces using scatterometry. In particular an approach to quantify the replication fidelity of high volume manufacturing processes such as polymer injection moulding is presented. Both periodic channels and semi-spherical structures were fabricated on nickel shims used for later injection moulding of Cyclic-olefin-copolymer (COC) substrate were the sub-μm features where ultimately transferred. The scatterometry system was validated using calibrated atomic force microscopy measurements and a model based on scalar diffraction theory employed to calculate the expected angular distribution of the reflected and the transmitted intensity for the nickel surfaces and structured COC and, respectively.

Magnetic assembly of transparent and conducting graphene-based functional composites

NASA Astrophysics Data System (ADS)

Le Ferrand, Hortense; Bolisetty, Sreenath; Demirörs, Ahmet F.; Libanori, Rafael; Studart, André R.; Mezzenga, Raffaele

2016-06-01

Innovative methods producing transparent and flexible electrodes are highly sought in modern optoelectronic applications to replace metal oxides, but available solutions suffer from drawbacks such as brittleness, unaffordability and inadequate processability. Here we propose a general, simple strategy to produce hierarchical composites of functionalized graphene in polymeric matrices, exhibiting transparency and electron conductivity. These are obtained through protein-assisted functionalization of graphene with magnetic nanoparticles, followed by magnetic-directed assembly of the graphene within polymeric matrices undergoing sol-gel transitions. By applying rotating magnetic fields or magnetic moulds, both graphene orientation and distribution can be controlled within the composite. Importantly, by using magnetic virtual moulds of predefined meshes, graphene assembly is directed into double-percolating networks, reducing the percolation threshold and enabling combined optical transparency and electrical conductivity not accessible in single-network materials. The resulting composites open new possibilities on the quest of transparent electrodes for photovoltaics, organic light-emitting diodes and stretchable optoelectronic devices.

Detection of aflatoxin and surface mould contaminated figs by using Fourier transform near-infrared reflectance spectroscopy.

PubMed

Durmuş, Efkan; Güneş, Ali; Kalkan, Habil

2017-01-01

Aflatoxins are toxic metabolites that are mainly produced by members of the Aspergillus section Flavi on many agricultural products. Certain agricultural products such as figs are known to be high risk products for aflatoxin contamination. Aflatoxin contaminated figs may show a bright greenish yellow fluorescence (BGYF) under ultraviolet (UV) light at a wavelength of 365 nm. Traditionally, BGYF positive figs are manually selected by workers. However, manual selection depends on the expertise level of the workers and it may cause them skin-related health problems due to UV radiation. In this study, we propose a non-invasive approach to detect aflatoxin and surface mould contaminated figs by using Fourier transform near-infrared (FT-NIR) reflectance spectroscopy. A classification accuracy of 100% is achieved for classifying the figs into aflatoxin contaminated/uncontaminated and surface mould contaminated/uncontaminated categories. In addition, a strong correlation has been found between aflatoxin and surface mould. Combined with pattern classification methods, the NIR spectroscopy can be used to detect aflatoxin contaminated figs non-invasively. Furthermore, a positive correlation between surface mould and aflatoxin contamination leads to a promising alternative indicator for the detection of aflatoxin-contaminated figs. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

Effect of particle size and percentages of Boron carbide on the thermal neutron radiation shielding properties of HDPE/B4C composite: Experimental and simulation studies

NASA Astrophysics Data System (ADS)

Soltani, Zahra; Beigzadeh, Amirmohammad; Ziaie, Farhood; Asadi, Eskandar

2016-10-01

In this paper the effects of particle size and weight percentage of the reinforcement phase on the absorption ability of thermal neutron by HDPE/B4C composites were investigated by means of Monte-Carlo simulation method using MCNP code and experimental studies. The composite samples were prepared using the HDPE filled with different weight percentages of Boron carbide powder in the form of micro and nano particles. Micro and nano composite were prepared under the similar mixing and moulding processes. The samples were subjected to thermal neutron radiation. Neutron shielding efficiency in terms of the neutron transmission fractions of the composite samples were investigated and compared with simulation results. According to the simulation results, the particle size of the radiation shielding material has an important role on the shielding efficiency. By decreasing the particle size of shielding material in each weight percentages of the reinforcement phase, better radiation shielding properties were obtained. It seems that, decreasing the particle size and homogeneous distribution of nano forms of B4C particles, cause to increase the collision probability between the incident thermal neutron and the shielding material which consequently improve the radiation shielding properties. So, this result, propose the feasibility of nano composite as shielding material to have a high performance shielding characteristic, low weight and low thick shielding along with economical benefit.

Fabrication of scalable tissue engineering scaffolds with dual-pore microarchitecture by combining 3D printing and particle leaching.

PubMed

Mohanty, Soumyaranjan; Sanger, Kuldeep; Heiskanen, Arto; Trifol, Jon; Szabo, Peter; Dufva, Marin; Emnéus, Jenny; Wolff, Anders

2016-04-01

Limitations in controlling scaffold architecture using traditional fabrication techniques are a problem when constructing engineered tissues/organs. Recently, integration of two pore architectures to generate dual-pore scaffolds with tailored physical properties has attracted wide attention in tissue engineering community. Such scaffolds features primary structured pores which can efficiently enhance nutrient/oxygen supply to the surrounding, in combination with secondary random pores, which give high surface area for cell adhesion and proliferation. Here, we present a new technique to fabricate dual-pore scaffolds for various tissue engineering applications where 3D printing of poly(vinyl alcohol) (PVA) mould is combined with salt leaching process. In this technique the sacrificial PVA mould, determining the structured pore architecture, was filled with salt crystals to define the random pore regions of the scaffold. After crosslinking the casted polymer the combined PVA-salt mould was dissolved in water. The technique has advantages over previously reported ones, such as automated assembly of the sacrificial mould, and precise control over pore architecture/dimensions by 3D printing parameters. In this study, polydimethylsiloxane and biodegradable poly(ϵ-caprolactone) were used for fabrication. However, we show that this technique is also suitable for other biocompatible/biodegradable polymers. Various physical and mechanical properties of the dual-pore scaffolds were compared with control scaffolds with either only structured or only random pores, fabricated using previously reported methods. The fabricated dual-pore scaffolds supported high cell density, due to the random pores, in combination with uniform cell distribution throughout the scaffold, and higher cell proliferation and viability due to efficient nutrient/oxygen transport through the structured pores. In conclusion, the described fabrication technique is rapid, inexpensive, scalable, and compatible with different polymers, making it suitable for engineering various large scale organs/tissues. Copyright © 2015. Published by Elsevier B.V.

Two underestimated threats in food transportation: mould and acceleration

PubMed Central

Janssen, S.; Pankoke, I.; Klus, K.; Schmitt, K.; Stephan, U.; Wöllenstein, J.

2014-01-01

Two important parameters are often neglected in the monitoring of perishable goods during transport: mould contamination of fresh food and the influence of acceleration or vibration on the quality of a product. We assert the claim that it is necessary to focus research on these two topics in the context of intelligent logistics in this opinion paper. Further, the technical possibilities for future measurement systems are discussed. By measuring taste deviations, we verified the effect on the quality of beer at different vibration frequencies. The practical importance is shown by examining transport routes and market shares. The general feasibility of a mobile mould detection system is established by examining the measurement resolution of semiconductor sensors for mould-related gases. Furthermore, as an alternative solution, we present a concept for a miniaturized and automated culture-medium-based system. Although there is a lack of related research to date, new efforts can make a vital contribution to the reduction of losses in the logistic chains for several products. PMID:24797139

Two underestimated threats in food transportation: mould and acceleration.

PubMed

Janssen, S; Pankoke, I; Klus, K; Schmitt, K; Stephan, U; Wöllenstein, J

2014-06-13

Two important parameters are often neglected in the monitoring of perishable goods during transport: mould contamination of fresh food and the influence of acceleration or vibration on the quality of a product. We assert the claim that it is necessary to focus research on these two topics in the context of intelligent logistics in this opinion paper. Further, the technical possibilities for future measurement systems are discussed. By measuring taste deviations, we verified the effect on the quality of beer at different vibration frequencies. The practical importance is shown by examining transport routes and market shares. The general feasibility of a mobile mould detection system is established by examining the measurement resolution of semiconductor sensors for mould-related gases. Furthermore, as an alternative solution, we present a concept for a miniaturized and automated culture-medium-based system. Although there is a lack of related research to date, new efforts can make a vital contribution to the reduction of losses in the logistic chains for several products.

Nasoalveolar moulding for children with unilateral cleft lip and palate.

PubMed

Chammanam, Shaju George; Biswas, P P; Kalliath, Ranjith; Chiramel, Siji

2014-06-01

Cleft lip and palate represents the most frequently occurring congenital deformity second only to club foot deformity in our country. Wide alveolar clefts if not preceded by pre surgical orthodontic adjuncts like nasoalveolar moulding, may affect the final outcome of the primary surgery. Presurgical nasoalveolar moulding is to align and approximate the alveolar cleft segments while at the same time achieving correction of the nasal cartilage and soft tissue deformity. The device we used is designed by Barry Grayson. It is simple to fabricate, causes less discomfort to the patient and optimum results are achieved in three months of time, compared to other complicated appliances like Latham's which are more invasive. A child of 3 months presented with a complaint of unilateral cleft deformity on one side of the face. After three months of nasoalveolar moulding considerable changes were observed. The widths of the cleft alveolus were reduced and the nasal contours of columella on the cleft side showed considerable improvement.

Effect of three mycotoxin adsorbents on growth performance, nutrient retention and meat quality in broilers fed on mould-contaminated feed.

PubMed

Liu, Y L; Meng, G Q; Wang, H R; Zhu, H L; Hou, Y Q; Wang, W J; Ding, B Y

2011-04-01

1. A study was conducted to investigate the effects of an esterified glucomannan (EGM), a hydrated sodium calcium aluminosilicate (HSCAS) and a compound mycotoxin adsorbent (CMA) on performance, nutrient retention and meat quality in broilers fed on mould-contaminated feed. Mould-contaminated diets were prepared by replacing half of the non-contaminated maize in the basal diets with mould-contaminated maize, which contained 450·6 µg/kg of aflatoxin B1, 68·4 µg/kg of ochratoxin A and 320·5 µg/kg of T-2 toxin. 2. The mould-contaminated diet significantly decreased body weight gain (BWG) between 10 and 21 d, feed intake (FI) between 35 and 42 d, the apparent retention of crude lipid and phosphorus, and the lightness (L*) value of breast and thigh muscle. It also significantly increased the redness (a*) and yellowness (b*) value in breast muscle and the b* value in thigh muscle. 3. The addition of 0·2% HSCAS significantly increased FI between 35 and 42 d and the apparent retention of phosphorus. Supplementation with 0·1% CMA in the contaminated diet significantly improved BWG from 10 to 21 d, and increased FI from 35 to 42 d and from 10 to 42 d. CMA also significantly increased the apparent retention of crude lipid, crude protein, ash and phosphorus. All three mycotoxin-adsorbent treatments significantly improved the L* values of breast and thigh muscle when compared with the mould-contaminated group. Supplementation with 0·1% CMA in the contaminated diet significantly decreased b* value and improved tenderness in thigh muscle. 0·05% EGM significantly decreased b* value of thigh muscle compared to mould-contaminated group. 4. The results indicated that mycotoxins in contaminated feed retard growth, nutrient retention and meat quality, whereas the addition of 0·05% EGM, 0·2% HSCAS or 0·1% CMA prevents the adverse effects of mycotoxins to varying extents, with 0·1% CMA being the most effective adsorbent treatment.

Uniform irradiation of irregularly shaped cavities for photodynamic therapy.

PubMed

Rem, A I; van Gemert, M J; van der Meulen, F W; Gijsbers, G H; Beek, J F

1997-03-01

It is difficult to achieve a uniform light distribution in irregularly shaped cavities. We have conducted a study on the use of hollow 'integrating' moulds for more uniform light delivery of photodynamic therapy in irregularly shaped cavities such as the oral cavity. Simple geometries such as a cubical box, a sphere, a cylinder and a 'bottle-neck' geometry have been investigated experimentally and the results have been compared with computed light distributions obtained using the 'radiosity method'. A high reflection coefficient of the mould and the best uniform direct irradiance possible on the inside of the mould were found to be important determinants for achieving a uniform light distribution.

[Onychocola canadensis Sigler in onychomycosis : A new dermatophyte-like mould in Germany].

PubMed

Nenoff, P; Schorlemmer, B; Uhrlaß, S; Baunacke, A; Baunacke, A; Friedrichs, C; Iffländer, J; Syhre, E; Schneider, A; Krüger, C; Maier, T

2016-09-01

Moulds or non-dermatophyte moulds (NDM) are being increasingly isolated as causative agent of onychomycoses. Known causes of a NDM-OM are Scopulariopsis brevicaulis, Fusarium, Aspergillus, Acremonium, Neoscytalidium dimidiatum, Arthrographis kalrae, and Chaetomium. In this article, 5 patients with suspected nail infection due to Onychocola canadensis are reported for the first time in Germany. Systemic antifungal agents are not considered to be effective in NDM onychomycosis. In individual cases, however, terbinafine seems to be effective in Onychocola canadensis infection of the nails. Treatment of choice represents, however, nontraumatic nail avulsion using 40 % urea ointment followed by antifungal nail lacquer with ciclopirox olamine or amorolfine.

Three-dimensional bioactive glass implants fabricated by rapid prototyping based on CO(2) laser cladding.

PubMed

Comesaña, R; Lusquiños, F; Del Val, J; López-Álvarez, M; Quintero, F; Riveiro, A; Boutinguiza, M; de Carlos, A; Jones, J R; Hill, R G; Pou, J

2011-09-01

Three-dimensional bioactive glass implants were produced by rapid prototyping based on laser cladding without using moulds. CO(2) laser radiation was employed to melt 45S5 and S520 bioactive glass particles and to deposit the material layer by layer following a desired geometry. Controlled thermal input and cooling rate by fine tuning of the processing parameters allowed the production of crack-free fully dense implants. Microstructural characterization revealed chemical composition stability, but crystallization during processing was extensive when 45S5 bioactive glass was used. Improved results were obtained using the S520 bioactive glass, which showed limited surface crystallization due to an expanded sintering window (the difference between the glass transition temperature and crystallization onset temperature). Ion release from the S520 implants in Tris buffer was similar to that of amorphous 45S5 bioactive glass prepared by casting in graphite moulds. Laser processed S520 scaffolds were not cytotoxic in vitro when osteoblast-like MC3T3-E1 cells were cultured with the dissolution products of the glasses; and the MC3T3-E1 cells attached and spread well when cultured on the surface of the materials. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Indoor and Outdoor Surface-Growing Fungi Contamination at Higher Institutional Buildings in a Malaysian University

NASA Astrophysics Data System (ADS)

Er, C. M.; Sunar, N. M.; Leman, A. M.; Khalid, A.; Ali, R.; Zaidi, E.; Azhar, A. T. S.

2018-04-01

Surface-growing indoor and outdoor fungi were assessed using swabbing method to investigate the indoor contamination. The painted wall surface samples were collected from two institutional buildings (B1 and B2) of a university in southern Peninsular Malaysia; indoors and outdoors. The mould concentrations varied widely between indoor and outdoor surface samples of both buildings. The total indoor surface-growing mould concentration (8776.49 CFU/cm2) is significantly higher (p<0.05) than the total concentration of outdoor surface growing mould (209.91 CFU/cm2). Respectively, the mean concentration of indoor surface-growing mould (18920.13 CFU/cm2 for B1 and 3704.67 CFU/cm2 for B2) is significantly higher than their outdoor counterparts (99.95 CFU/cm2 for b1 and for 319.86 CFU/cm2 b2) at these buildings. Besides, various air quality parameters (relative humidity, temperature and air velocity) were also measured indoors and outdoors during the study and violation of the guideline provided by ICOP-IAQ 2010 were proven in indoor environment in both buildings. The results of this assessment showed that the indoor environments of both institutional buildings were contaminated by the surface-growing mould. It also suggested the faulty designs and/or usages of building material in these institutional buildings contributed toward the contamination. An innovative solution is needed to correct the problems.

Occurrence of mycotoxins and yeasts and moulds identification in corn silages in tropical climate.

PubMed

Carvalho, B F; Ávila, C L S; Krempser, P M; Batista, L R; Pereira, M N; Schwan, R F

2016-05-01

This study was aimed to identify yeasts and moulds as well as to detect mycotoxin in corn silages in southern Minas Gerais, Brazil. Corn silages from 36 farms were sampled to analyse dry matter, crude protein, ether extract, ash, neutral detergent fibre, nonfibre carbohydrates and mycotoxins contents, yeasts and moulds population, pH and temperature values. The mycotoxins found in high frequency were aflatoxin in 77·7% of analysed samples, ochratoxin (33·3%) and zearalenone (22·2%). There was no significant correlation between the mycotoxin concentration and the presence of moulds. The pH was negatively correlated with ochratoxin concentration. Aspergillus fumigatus was identified in all silages that presented growth of moulds. Ten different yeast species were identified using the culture-dependent method: Candida diversa, Candida ethanolica, Candida rugosa, Issatchenkia orientalis, Kluyveromyces marxianus, Pichia manshurica, Pichia membranifaciens, Saccharomyces cerevisiae, Trichosporon asahii and Trichosporon japonicum. Another six different yeast species were identified using the culture-independent method. A high mycotoxin contamination rate (91·6% of the analysed silages) was observed. The results indicated that conventional culturing and PCR-DGGE should be combined to optimally describe the microbiota associated with corn silage. This study provides information about the corn silage fermentation dynamics and our findings are relevant to optimization of this silage fermentation. © 2016 The Society for Applied Microbiology.

Common cold among pre-school children in China - associations with ambient PM10 and dampness, mould, cats, dogs, rats and cockroaches in the home environment.

PubMed

Norbäck, Dan; Lu, Chan; Zhang, Yinping; Li, Baizhan; Zhao, Zhuohui; Huang, Chen; Zhang, Xin; Qian, Hua; Sundell, Jan; Deng, Qihong

2017-06-01

There is some evidence that dampness, mould and cockroaches can increase the risk of respiratory infections in children but few studies exist from China on this topic. Aim To study associations between domestic early life exposure to biological indoor factors (dampness, mould, cats, dogs, rats, cockroaches), cleaning habits and common cold among pre-school children across China. Children aged 3-6years (n=39,782) were recruited from randomly selected day care centres in seven cities in China. Data on common cold and prenatal and postnatal exposure to dampness, mould, windowpane condensation in wintertime (WPC), cats, dogs, cockroaches and rats were assessed by a parentally administered questionnaire. Data on annual ambient temperature and PM 10 was assessed on city level. Associations between high frequency (>5 colds per year) and long duration (≥2weeks) of common colds in the past year and exposure were calculated by multilevel logistic regression. A total of 9.2% had a high frequency and 11.9% had long duration of common cold. Exposure to mould (OR=1.38, 95% CI 1.24-1.53) and WPC (OR 1.23, 95%CI 1.13-1.33) at birth was associated with frequent common cold. Exposure to dogs at birth was associated with long duration of common cold. (OR=1.22, 95% CI 1.06-1.41). Exposure to mould (OR=1.36, 95% CI 1.22-1.54), WPC (OR=1.27, 95%CI 1.17-1.39) and water leakage (OR 1.34, 95% CI 1.20-1.49) in the current home was associated with frequent common cold. Presence of cockroaches were positively (OR=1.12, 95% CI 1.02-1.24) and presence of rats (OR=0.86, 95% CI 0.77-0.96) negatively associated with high frequency of common cold. Daily cleaning was negatively associated with frequent common cold (OR=0.89, 95% CI 0.81-0.97). Similar associations for mould, WPC, cockroaches and rats were found for long duration. Ambient PM 10 (OR=1.21, 95% CI 1.21-1.35 per 10μg/m 3 ) and temperature (OR=1.13, 95% CI 1.06-1.35 °C) on city level were associated with high frequency of common cold. Associations between cat keeping and high frequency of common cold were found only in southern China. Associations with cockroaches were stronger in northern China. Associations with dampness and mould were the same in the north and south. Indoor mould, water damage, windowpane condensation, cockroaches and keeping cats or dogs as pets can be risk factors for common cold while daily cleaning can be protective factor. PM 10 and a warmer climate zone can be other risk factors for common cold. Copyright © 2017 Elsevier Ltd. All rights reserved.

Combination of microscopic model and VoF-multiphase approach for numerical simulation of nodular cast iron solidification

NASA Astrophysics Data System (ADS)

Subasic, E.; Huang, C.; Jakumeit, J.; Hediger, F.

2015-06-01

The ongoing increase in the size and capacity of state-of-the-art wind power plants is highlighting the need to reduce the weight of critical components, such as hubs, main shaft bearing housings, gear box housings and support bases. These components are manufactured as nodular iron castings (spheroid graphite iron, or SGI). A weight reduction of up to 20% is achievable by optimizing the geometry to minimize volume, thus enabling significant downsizing of wind power plants. One method for enhancing quality control in the production of thick-walled SGI castings, and thus reducing tolerances and, consequently, enabling castings of smaller volume is via a casting simulation of mould filling and solidification based on a combination of microscopic model and VoF-multiphase approach. Coupled fluid flow with heat transport and phase transformation kinetics during solidification is described by partial differential equations and solved using the finite volume method. The flow of multiple phases is described using a volume of fluid approach. Mass conservation equations are solved separately for both liquid and solid phases. At the micro-level, the diffusion-controlled growth model for grey iron eutectic grains by Wetterfall et al. is combined with a growth model for white iron eutectic grains. The micro-solidification model is coupled with macro-transport equations via source terms in the energy and continuity equations. As a first step the methodology was applied to a simple geometry to investigate the impact of mould-filling on the grey-to-white transition prediction in nodular cast iron.

Fuel poverty increases risk of mould contamination, regardless of adult risk perception & ventilation in social housing properties.

PubMed

Sharpe, Richard A; Thornton, Christopher R; Nikolaou, Vasilis; Osborne, Nicholas J

2015-06-01

Fuel poverty affects 2.4 million UK homes leading to poor hygrothermal conditions and risk of mould and house dust mite contaminations, which in turn increases risk of asthma exacerbation. For the first time we assess how fuel poverty, occupants' risk perception and use of mechanical ventilation mediate the risk of mould contamination in social housing. Postal questionnaires were sent to 3867 social housing properties to collect adult risk perception, and demographic and environmental information on occupants. Participant details were linked to data pertaining to the individual properties. Multiple logistic regression was used to calculate odds ratios and confidence intervals while allowing for clustering of individuals coming from the same housing estate. We used Structured Equation Modelling and Goodness of Fit analysis in mediation analyses to examine the role of fuel poverty, risk perception, use of ventilation and energy efficiency. Eighteen percent of our target social housing populations (671 households) were included into our study. High risk perception (score of 8-10) was associated with reduced risk of mould contamination in the bedrooms of children (OR 0.5 95% CI; 0.3-0.9) and adults (OR 0.4 95% CI; 0.3-0.7). High risk perception of living with inadequate heating and ventilation reduced the risk of mould contamination (OR 0.5 95% CI; 0.3-0.8 and OR 0.5 95% CI; 0.3-0.7, respectively). Participants living with inadequate heating and not heating due to the cost of fuel had an increased risk of mould contamination (OR 3.4 95% CI; 2.0-5.8 and OR 2.2 95% CI; 1.5-3.2, respectively). Increased risk perception and use of extractor fans did not mediate the association between fuel poverty behaviours and increased risk of mould contamination. Fuel poverty behaviours increased the risk of mould contamination, which corresponds with existing literature. For the first time we used mediation analysis to assess how this association maybe modified by occupant behaviours. Increased risk perception and use of extractor fans did not modify the association between fuel poverty and mould contamination. This suggests that fuel poor populations may not benefit from energy efficiency interventions due to ineffective heating and ventilation practices of those occupants residing participating households. Our findings may be modified by a complex interaction between occupant behaviours and the built environment. We found that participant age, occupancy, SES, pets, drying washing indoors, geographic location, architectural design/age of the property, levels of insulation and type of heating regulated risk of mould contamination. Fuel poverty behaviours affected around a third of participating households and represent a risk factor for increased exposures to damp and mouldy conditions, regardless of adult risk perception, heating and ventilation practices. This requires multidisciplinary approach to assess the complex interaction between occupant behaviours, risk perception, the built environment and the effective use of heating and ventilation practices. Our findings have implications for housing policies and future housing interventions. Effective communication strategies focusing on awareness and perception of risk may help address indoor air quality issues. This must be supported by improved household energy efficiency with the provision of more effective heating and ventilation strategies, specifically to help alleviate those suffering from fuel poverty. Copyright © 2015 Elsevier Ltd. All rights reserved.

Three-dimensional autologous cartilage framework fabrication assisted by new additive manufactured ear-shaped templates for microtia reconstruction.

PubMed

Zhou, Jiayu; Pan, Bo; Yang, Qinghua; Zhao, Yanyong; He, Leren; Lin, Lin; Sun, Hengyun; Song, Yupeng; Yu, Xiaobo; Sun, Zhongyang; Jiang, Haiyue

2016-10-01

During microtia reconstruction, the intraoperative design of the cartilage framework is important for the appearance and symmetry of the bilateral auricles. Templates (traditionally, the X-ray film template) are usually utilized to complete the task, which can provide cues regarding size, cranioauricular angle and positioning to the surgeons. With a combination of three-dimensional (3D) scanning and additive manufacturing (AM) techniques, we utilized two different ear-shaped templates (sheet moulding and 3D templates) during the fabrication of 3D-customized autologous cartilage frameworks for auricle reconstruction. Forty unilateral microtia patients were included in the study. All the patients underwent auricle reconstruction using the tissue-expanding technique assisted by the new AM templates. Images were processed using computer-aided design software and exported to print two different AM ear-shaped templates: sheet moulding and 3D. Both templates were assisted by the 3D framework fabrication. The 3D images of each patient's head were captured preoperatively using a 3D scanner. X-ray film templates were also made for the patients. The lengths and widths of the contralateral auricles, X-ray film and sheet moulding templates were measured in triplicate. The error of the template and the contralateral auricle were used to compare the accuracy between the two templates. Between January and May 2014, 40 unilateral microtia patients aged 6-29 years were included in this study. All patients underwent auricle reconstruction using autogenous costal cartilage. The sterilized AM templates were used to assist in the framework fabrication. The operative time was decreased by an average of 15 min compared with the method assisted by the X-ray film template. Postoperative appearance evaluation (based on five indexes: symmetry, length, width, cranioauricular angle and the substructure of the reconstructed ear) was performed by both the doctors and the patients (or their parents). Follow-up (ranging from 9 to 18 months) showed that all of the patients obtained satisfactory results with life-like 3D configuration and symmetric cranioauricular angle. The follow-up showed that no surgery-related complications occurred. Comparing the accuracy of the X-ray film and sheet moulding templates, the average errors of length were 1.8 mm ± 1.44 mm and 0.39 mm ± 0.35 mm, respectively, and the average width errors were 1.32 mm ± 0.88 mm and 0.3 mm ± 0.47 mm, respectively. The new sheet moulding template was more accurate than the X-ray template. The new sheet-moulding template is much more accurate than the traditional X-ray film template. Framework fabrication assisted by accurate 3D and informative AM templates contributed to individualized cartilage framework fabrication and satisfactory results. Copyright © 2016 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

Mould design and manufacturing considerations of honeycomb biocomposites with transverse fibre direction for aerospace application

NASA Astrophysics Data System (ADS)

Manan, N. H.; Majid, D. L.; Romli, F. I.

2016-10-01

Sandwich structures with honeycomb core are known to significantly improve stiffness at lower weight and possess high flexural rigidity. They have found wide applications in aerospace as part of the primary structures, as well as the interior paneling and floors. High performance aluminum and aramid are the typical materials used for the purpose of honeycomb core whereas in other industries, materials such as fibre glass, carbon fibre, Nomex and also Kevlar reinforced with polymer are used. Recently, growing interest in developing composite structures with natural fibre reinforcement has also spurred research in natural fibre honeycomb material. The majority of the researches done, however, have generally emphasized on the usage of random chopped fibre and only a few are reported on development of honeycomb structure using unidirectional fibre as the reinforcement. This is mainly due to its processing difficulties, which often involve several stages to account for the arrangement of fibres and curing. Since the use of unidirectional fibre supports greater strength compared to random chopped fibre, a single-stage process in conjunction with vacuum infusion is suggested with a mould design that supports fibre arrangement in the direction of honeycomb loading.

Nanofibre distribution in composites manufactured with epoxy reinforced with nanofibrillated cellulose: model prediction and verification

NASA Astrophysics Data System (ADS)

Aitomäki, Yvonne; Westin, Mikael; Korpimäki, Jani; Oksman, Kristiina

2016-07-01

In this study a model based on simple scattering is developed and used to predict the distribution of nanofibrillated cellulose in composites manufactured by resin transfer moulding (RTM) where the resin contains nanofibres. The model is a Monte Carlo based simulation where nanofibres are randomly chosen from probability density functions for length, diameter and orientation. Their movements are then tracked as they advance through a random arrangement of fibres in defined fibre bundles. The results of the model show that the fabric filters the nanofibres within the first 20 µm unless clear inter-bundle channels are available. The volume fraction of the fabric fibres, flow velocity and size of nanofibre influence this to some extent. To verify the model, an epoxy with 0.5 wt.% Kraft Birch nanofibres was made through a solvent exchange route and stained with a colouring agent. This was infused into a glass fibre fabric using an RTM process. The experimental results confirmed the filtering of the nanofibres by the fibre bundles and their penetration in the fabric via the inter-bundle channels. Hence, the model is a useful tool for visualising the distribution of the nanofibres in composites in this manufacturing process.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Praher, B., E-mail: bernhard.praher@jku.at, E-mail: klaus.straka@jku.at, E-mail: jesenka.usanovic@jku.at, E-mail: georg.steinbichler@jku.at; Straka, K., E-mail: bernhard.praher@jku.at, E-mail: klaus.straka@jku.at, E-mail: jesenka.usanovic@jku.at, E-mail: georg.steinbichler@jku.at; Usanovic, J., E-mail: bernhard.praher@jku.at, E-mail: klaus.straka@jku.at, E-mail: jesenka.usanovic@jku.at, E-mail: georg.steinbichler@jku.at

We developed novel non-invasive ultrasound based systems for the measurement of temperature distributions in the screw-ante chamber, the detection of unmelted granules and for the monitoring of the plasticizing process along the screw channel. The temperature of the polymer melt stored in the screw ante-chamber after the plasticization should be homogeneous. However, in reality the polymer melt in the screw ante-chamber is not homogeneous. Due to the fact the sound velocity in a polymer melt is temperature depending, we developed a tomography system using the measured transit times of ultrasonic pulses along different sound paths for calculating the temperature distributionmore » in radial direction of a polymer melt in the screw ante-chamber of an injection moulding machine. For the detection of unmelted granules in the polymer melt we implemented an ultrasound transmission measurement. By analyzing the attenuation of the received pulses it is possible to detect unwanted inclusions. For the monitoring of the plasticizing process in the channels of the screw an ultrasonic pulse is transmitted into the barrel. By analyzing the reflected pulses it is possible to estimate solid bed and melt regions in the screw channel. The proposed systems were tested for accuracy and validity by simulations and test measurements.« less

The spectrum and aetiology of mycotic infections from a tertiary care hospital from Western part of India.

PubMed

Gandham, Nageswari Rajesh; Jadhav, Savita Vivek; Sardar, Moumita; Vyawahare, Chanda; Misra, Rabind Ranath

2013-10-01

In the past few years, there has been an increase in infections caused by fungal aetiology. This is mainly due to increase in sizes of populations which are at risk. Also, fungi which were previously considered as non-pathogenic have been increasingly implicated. Hence, this study was taken up. To assess the magnitude of mycotic infections in this set up. To assess the spectrum of fungi which are involved in various infections. Total 704 samples taken over two and half period were included. They consisted of various samples like sputum, blood, urine, sterile body fluids, corneal scrapings. These were processed by conventional mycological techniques. These included direct microscopy after Gram staining and KOH mount, culture on Sabouraud's dextrose agar (SDA), corn meal agar, brain heart infusion (BHI), brain heart infusion agar (BHIA) and others, as required. For non-albicans Candida, the automated Vitek 2 C system was used. Various moulds and yeasts were identified up to genus level and species level. Of 704 samples, 336 (48%) were positive for fungal culture. Of these, 244 isolates were yeast like fungi, 81 were moulds, 7 were yeasts and 4 were dimorphic. Among blood stream infections, non-albicans Candida were the commonest isolates. In the urine samples, C. albicans was the commonest isolate. From corneal scrapings, only moulds and dimorphic fungi were isolated. Incidence of non- albicans Candidal infections is increasing. Culture and identification of mycotic infections is essential for commencement of suitable antifungal therapy.

Advances for the Topographic Characterisation of SMC Materials

PubMed Central

Calvimontes, Alfredo; Grundke, Karina; Müller, Anett; Stamm, Manfred

2009-01-01

For a comprehensive study of Sheet Moulding Compound (SMC) surfaces, topographical data obtained by a contact-free optical method (chromatic aberration confocal imaging) were systematically acquired to characterise these surfaces with regard to their statistical, functional and volumetrical properties. Optimal sampling conditions (cut-off length and resolution) were obtained by a topographical-statistical procedure proposed in the present work. By using different length scales specific morphologies due to the influence of moulding conditions, metallic mould topography, glass fibre content and glass fibre orientation can be characterized. The aim of this study is to suggest a systematic topographical characterization procedure for composite materials in order to study and recognize the influence of production conditions on their surface quality.

Self heating during stretch blow moulding and induced properties

NASA Astrophysics Data System (ADS)

Luo, Yun-Mei; Chevalier, Luc

2018-05-01

The great influence of temperature on polymer's behavior is well known and a 10°C increase can lead to a 10 time reduction of the viscosity for example. The necessity to take into account the self heating phenomena, that may have impact on induced properties, appears to be crucial for thermoforming process simulation and in particular for ISBM of PET. In order to evaluate this self-heating value, preforms have been blown with at different initial temperature followed using a thermal camera. The increase of temperature is determined comparing initial temperature in zone 1-2 with final temperature in zone 3-4. For an identical final volume of the blown preform, the influence of initial temperature on self-heating is discussed. Back to room temperature, induced mechanical properties are determined by two methods: (i) specimens are cut out from the bottle and prepared to be tested on uniaxial tension machine; (ii) bottles are blown under different pressures to follow the strain field using digital image correlation. Coupled with a finite element simulation managed on the bottle, these results allow the identification of the induced mechanical properties. Comparison between the self-heating and the induced modulus is managed and the effect of the self heating on the free blown shapes and induced properties is discussed.

Technique Incorporating Cooling & Contraction / Expansion Analysis to Illustrate Shrinkage Tendency in Cast Irons

NASA Astrophysics Data System (ADS)

Stan, S.; Chisamera, M.; Riposan, I.; Neacsu, L.; Cojocaru, A. M.; Stan, I.

2017-06-01

With the more widespread adoption of thermal analysis testing, thermal analysis data have become an indicator of cast iron quality. The cooling curve and its first derivative display patterns that can be used to predict the characteristics of a cast iron. An experimental device was developed with a technique to simultaneously evaluate cooling curves and expansion or contraction of cast metals during solidification. Its application is illustrated with results on shrinkage tendency of ductile iron treated with FeSiMgRECa master alloy and inoculated with FeSi based alloys, as affected by mould rigidity (green sand and resin sand moulds). Undercooling at the end of solidification relative to the metastable (carbidic) equilibrium temperature and the expansion within the solidification sequence appear to have a strong influence on the susceptibility to macro - and micro - shrinkage in ductile iron castings. Green sand moulds, as less rigid moulds, encourage the formation of contraction defects, not only because of high initial expansion values, but also because of a higher cooling rate during solidification, and consequently, increased undercooling below the metastable equilibrium temperature up to the end of solidification.

Growth and reproduction of laboratory-reared neanurid Collembola using a novel slime mould diet

PubMed Central

Hoskins, Jessica L.; Janion-Scheepers, Charlene; Chown, Steven L.; Duffy, Grant A.

2015-01-01

Although significant progress has been made using insect taxa as model organisms, non-tracheated terrestrial arthropods, such as Collembola, are underrepresented as model species. This underrepresentation reflects the difficulty in maintaining populations of specialist Collembola species in the laboratory. Until now, no species from the family Neanuridae have been successfully reared. Here we use controlled growth experiments to provide explicit evidence that the species Neanura muscorum can be raised under laboratory conditions when its diet is supplemented with slime mould. Significant gains in growth were observed in Collembola given slime mould rather than a standard diet of algae-covered bark. These benefits are further highlighted by the reproductive success of the experimental group and persistence of laboratory breeding stocks of this species and others in the family. The necessity for slime mould in the diet is attributed to the ‘suctorial’ mouthpart morphology characteristic of the Neanuridae. Maintaining laboratory populations of neanurid Collembola species will facilitate their use as model organisms, paving the way for studies that will broaden the current understanding of the environmental physiology of arthropods. PMID:26153104

Mycotic and aflatoxin contamination in Myristica fragrans seeds (nutmeg) and Capsicum annum (chilli), packaged in Italy and commercialized worldwide.

PubMed

Pesavento, G; Ostuni, M; Calonico, C; Rossi, S; Capei, R; Lo Nostro, A

2016-01-01

Aflatoxins are secondary metabolites of moulds known to be carcinogenic for humans, and therefore should not be ingested in high doses. This study aimed to determine the level of mould and aflatoxin contamination in dehydrated chilli and nutmeg imported from India and Indonesia, respectively, packaged in Italy, and commercialized worldwide. We tested 63 samples of chilli (22 sanitized through heat treatment and 41 not heat-treated) and 52 samples of nutmeg (22 heat-treated and 30 not heat-treated) for aflatoxin, moulds and moisture content. Heat-treated samples were less contaminated than untreated samples. Spices in powder form (both chilli and nutmeg) were more contaminated than whole ones. In untreated spices, we observed a positive correlation between mould and moisture content. Of the powdered nutmeg and chilli samples, 72.5% and 50% tested positive for aflatoxin contamination, with a range of 0-17.2 μg kg(-1) and 0-10.3 μg kg(-1), respectively. The steam treatment of spices would be useful in reducing the initial amount of moulds. Although the risk from the consumption of spices contaminated with aflatoxins is minimal, owing to the small amount used in food, preventive screening of the whole food chain is very important, especially because the most frequently identified toxin was B1, which is the most dangerous of the four toxins (B1, B2, G1, G2).

Preliminary antifungal activity assay of selected chlorine-containing derivatives of xanthone and phenoxyethyl amines.

PubMed

Klesiewicz, Karolina; Żelaszczyk, Dorota; Trojanowska, Danuta; Bogusz, Bożena; Małek, Marianna; Waszkielewicz, Anna; Szkaradek, Natalia; Karczewska, Elżbieta; Marona, Henryk; Budak, Alicja

2018-06-20

The aim of this study was to preliminary evaluate antifungal activity diverse group of chlorine-containing xanthone and phenoxyethyl amine derivatives - and to select most promising compounds for further studies. The antifungal efficacy of 16 compounds was tested with qualitative and quantitative methods against both reference and clinical strains of dermatophytes, moulds and yeasts. The disc-diffusion method has demonstrated that from 16 tested compounds, 7 possess good antifungal activity against dermatophytes and/or moulds while none of them has shown good efficacy against yeasts or bacterial strains. The most active compounds (2, 4, 10, 11, 12, 15, 16) were tested quantitatively by broth dilution method to obtain MIC values. The MIC values against dermatophytes ranged from 8 to 64 μg/mL. Compound 2 was the most active one against dermatophytes (MIC 50 and MIC 90 were 8 μg/mL). The MIC values for moulds ranged from 16 to 256 μg/mL. Compound 4 was the most active one against moulds, with MIC 50 and MIC 90 values amounting to 32 μg/mL. Among the tested compounds, compound 4 (derivative of xanthone) was the most active one and expressed good antifungal efficacy against clinical strains of dermatophytes and moulds. However, another xanthone derivative (compound 2) was the most active and selective against dermatophytes. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Microbiological contamination with moulds in work environment in libraries and archive storage facilities.

PubMed

Zielinska-Jankiewicz, Katarzyna; Kozajda, Anna; Piotrowska, Malgorzata; Szadkowska-Stanczyk, Irena

2008-01-01

Microbiological contamination with fungi, including moulds, can pose a significant health hazard to those working in archives or museums. The species involved include Aspergillus, Penicillium, Geotrichum, Alternaria, Cladosporium, Mucor, Rhizopus, Trichoderma, Fusarium which are associated mostly with allergic response of different types. The aim of the study was to analyse, both in quantitative and qualitative terms, workplace air samples collected in a library and archive storage facilities. Occupational exposure and the related health hazard from microbiological contamination with moulds were assessed in three archive storage buildings and one library. Air samples (total 60) were collected via impact method before work and at hourly intervals during work performance. Surface samples from the artifacts were collected by pressing a counting (RODAC) plate filled with malt extract agar against the surface of the artifacts. The air sample and surface sample analyses yielded 36 different mould species, classified into 19 genera, of which Cladosporium and Penicillium were the most prevalent. Twelve species were regarded as potentially pathogenic for humans: 8 had allergic and 11 toxic properties, the latter including Aspergillus fumigatus. Quantitative analysis revealed air microbiological contamination with moulds at the level ranging from 1.8 x 10(2)-2.3 x 10(3) cfu/m(3). In surface samples from library and archive artifacts, 11 fungal species were distinguished; the number of species per artifact varying from 1-6 and colony count ranging from 4 x 10(1) to 8-10(1) cfu/100 cm(2). Higher contamination levels were found only for Cladosporium cladosporioides (1.48 x 10(3) cfu/100 cm(2)) and Paecillomyces varioti (1.2 x 10(2) cfu/100 cm(2)). At the workposts examined, although no clearly visible signs of mould contamination could be found, the study revealed abundant micromycetes, with the predominant species of Cladosporium and Penicillium. The detected species included also potentially pathogenic microorganisms which can cause allergic and toxic effects, such as Aspergillus fumigatus, that could be hazardous to workers' health. For some species, the concentration levels exceeded the values considered the proposed hygienic standards for total microscopical fungi in occupational settings. The findings of the study point to unsatisfactory hygienic conditions at the worksites examined, resulting in microbiological contamination with moulds, as well as the necessity for prompt remedial activities on the part of the employers.

Exploring the associations between parent-reported biological indoor environment and airway-related symptoms and allergic diseases in children.

PubMed

Weber, Alisa; Fuchs, Nina; Kutzora, Susanne; Hendrowarsito, Lana; Nennstiel-Ratzel, Uta; von Mutius, Erika; Herr, Caroline; Heinze, Stefanie

2017-11-01

Asthma and allergic rhinitis are diseases which require special attention in childhood. Risk factors for these diseases are manifold and include environmental factors. Previous studies have shown associations between indoor mould and respiratory diseases in children. Besides indoor mould, organic waste storage, potted plants, pets and crowding could influence the microbial indoor environment at home and the respiratory health of children. Our aim was therefore to explore the associations of these factors with airway-related symptoms and respiratory diseases in preschoolers. In this cross-sectional study we evaluated data based on parent-questionnaires regarding the health of their children from the 2014/2015 Health Monitoring Units (GME) in Bavaria. Bivariate and multivariate odds ratios (OR) with 95% confidence intervals (95%-CI) were calculated with logistic regression to explore associations between exposures (visible mould, organic waste storage, potted plants, pets and crowding) and outcome variables (doctor diagnosed allergic rhinitis with symptoms in the last 12 months, doctor diagnosed asthma with symptoms in the last 12 months, 12 month prevalence of symptoms such as dry cough at night without a cold, wheeze, wheeze attacks and allergic rhinitis symptoms). We analysed data from 4732 children (response rate 56.7%) with a mean age of 5.3 years. Visible mould was present in 4.7% of all households and associated with doctor diagnosed asthma with symptoms in the last 12 months [aOR 2.16 (95%-CI 1.01-4.63)], wheeze in the last 12 months [aOR 1.60 (95%-CI 1.0-2.50)] and allergic rhinitis symptoms in the last 12 months [aOR 1.75 (95%-CI 1.07-2.87)]. Crowding was associated with dry cough at night without a cold in the last 12 months [aOR 1.71 (95%-CI 1.42-2.05). The other indoor factors showed no association with respiratory health of the children. Our results, in line with previous studies, showed positive associations between visible mould at home and airway-related symptoms and allergic diseases in children irrespective of the effect of the other considered indoor exposures. Despite the low prevalence of mould exposure in our study population, our results suggest intervention should be taken for those who do have visible mould exposure at home. Copyright © 2017 Elsevier GmbH. All rights reserved.

Research on burnout fault of moulded case circuit breaker based on finite element simulation

NASA Astrophysics Data System (ADS)

Xue, Yang; Chang, Shuai; Zhang, Penghe; Xu, Yinghui; Peng, Chuning; Shi, Erwei

2017-09-01

In the failure event of molded case circuit breaker, overheating of the molded case near the wiring terminal has a very important proportion. The burnout fault has become an important factor restricting the development of molded case circuit breaker. This paper uses the finite element simulation software to establish the model of molded case circuit breaker by coupling multi-physics field. This model can simulate the operation and study the law of the temperature distribution. The simulation results show that the temperature near the wiring terminal, especially the incoming side of the live wire, of the molded case circuit breaker is much higher than that of the other areas. The steady-state and transient simulation results show that the temperature at the wiring terminals is abnormally increased by increasing the contact resistance of the wiring terminals. This is consistent with the frequent occurrence of burnout of the molded case in this area. Therefore, this paper holds that the burnout failure of the molded case circuit breaker is mainly caused by the abnormal increase of the contact resistance of the wiring terminal.

Magnetic assembly of transparent and conducting graphene-based functional composites

PubMed Central

Le Ferrand, Hortense; Bolisetty, Sreenath; Demirörs, Ahmet F.; Libanori, Rafael; Studart, André R.; Mezzenga, Raffaele

2016-01-01

Innovative methods producing transparent and flexible electrodes are highly sought in modern optoelectronic applications to replace metal oxides, but available solutions suffer from drawbacks such as brittleness, unaffordability and inadequate processability. Here we propose a general, simple strategy to produce hierarchical composites of functionalized graphene in polymeric matrices, exhibiting transparency and electron conductivity. These are obtained through protein-assisted functionalization of graphene with magnetic nanoparticles, followed by magnetic-directed assembly of the graphene within polymeric matrices undergoing sol–gel transitions. By applying rotating magnetic fields or magnetic moulds, both graphene orientation and distribution can be controlled within the composite. Importantly, by using magnetic virtual moulds of predefined meshes, graphene assembly is directed into double-percolating networks, reducing the percolation threshold and enabling combined optical transparency and electrical conductivity not accessible in single-network materials. The resulting composites open new possibilities on the quest of transparent electrodes for photovoltaics, organic light-emitting diodes and stretchable optoelectronic devices. PMID:27354243

Tensile properties of compressed moulded Napier/glass fibre reinforced epoxy composites

NASA Astrophysics Data System (ADS)

Fatinah, T. S.; Majid, M. S. Abdul; Ridzuan, M. J. M.; Hong, T. W.; Amin, N. A. M.; Afendi, M.

2017-10-01

This paper describes the experimental investigation of the tensile properties of compressed moulded Napier grass fibres reinforced epoxy composites. The effect of treatment 5% sodium hydroxide (NaOH) concentrated solution and hybridization of Napier with CSM E-glass fibres on tensile properties was also studied. The untreated and treated Napier fibres with 25% fibre loading were fabricated with epoxy resin by a cold press process. 7% fibre loading of CSM glass fibre was hybrid as the skin layer for 18% fibre loading of untreated Napier grass fibre. The tensile tests were conducted using Universal Testing Machine in accordance with ASTM D638. The tensile properties of the untreated Napier/epoxy composites were compared with treated Napier/epoxy and untreated Napier/CSM/epoxy composites. The results demonstrated that the tensile performance of untreated Napier fibre composites was significantly improved by both of the modification; alkali treatment and glass fibre hybridization. Napier grass fibres showed promising potentials to be used as reinforcement in the polymer based composites.

Lumber recovery from ponderosa pine in northern California.

Treesearch

Susan Ernst; Pong W.Y.

1985-01-01

Lumber recovery information from 942 logs from old- and young-growth ponderosa pine (Pinus ponderosa Dougl. ex Laws.) trees in northern California is presented. More than 58 percent of the lumber volume was found in 5/4 Shop, Moulding, and Select grades. About 25 percent of the total lumber volume was Moulding, and 24 percent was Standard and...

Exploring Value-Added Options - Opportunities in Mouldings and Millwork

Treesearch

Bob Smith; Philip A. Araman

1997-01-01

The millwork industry, which includes manufacture of doors, windows, stair parts, blinds, mouldings, picture frame material, and assorted trim, can be a lucrative value-added opportunity for sawmills. Those entering the value-added millwork market often find that it is a great opportunity to generate greater profits from upper grades and utility species, such as yellow...

Protecting wood from mould, decay, and termites with multi-component biocide systems

Treesearch

Carol A. Clausen

2007-01-01

Biocides must be developed for controlling mould establishment on cellulose-based building materials. Accordingly, biocides intended for indoor applications must be non- toxic, non-volatile, odourless, hypoallergenic, and able to provide long-term protection under conditions of high humidity. Multi-component biocide systems were tested in American Wood-Preservers’...

Mould exposure in museum personnel.

PubMed

Kolmodin-Hedman, B; Blomquist, G; Sikström, E

1986-01-01

In the basement archives of a local arts and crafts museum where the books and bookkeeping registers were handled, a woman on the museum staff had had ten attacks of fever, chill, nausea and cough during one year. The symptoms appeared at the end of the working day and disappeared after one to three days at home. No symptoms could be detected during the summer holidays. The books stored in the basement archives had earlier been stored in a small house with a leaky roof, which had led to the growth of mould on the books. When the books were handled at the museum, they were still covered with mould. The exposure measurements showed 10(6) CFU/m3 and a total of 10(8) microorganisms/m3.

1. LOOKING NORTH AT THE BASIC OXYGEN STEELMAKING PLANT. THE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. LOOKING NORTH AT THE BASIC OXYGEN STEELMAKING PLANT. THE FLUX HANDLING BUILDING IS ON THE RIGHT, THE MOULD CONDITIONING BUILDING IS IN THE CENTER, THE BASIC OXYGEN PROCESS (BOP) SHOP IS IN THE CENTER BACKGROUND, AND OPEN HEARTH No. 2 BUILDING IS ON THE LEFT. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Soy matrix drug delivery systems obtained by melt-processing techniques.

PubMed

Vaz, Cláudia M; van Doeveren, Patrick F N M; Reis, Rui L; Cunha, António M

2003-01-01

The aim of this study was to develop new soy protein drug delivery matrix systems by melt-processing techniques, namely, extrusion and injection moulding. The soy matrix systems with an encapsulated drug (theophylline, TH) were previously compounded by extrusion performed at two different pH values, (i) pH 4 (SIpDtp) and (ii) pH 7 (SIDtp), and further injection-moulded into a desired shape. During the extrusion process the matrixes SIDtp were also cross-linked with glyoxal (0.6X-SIDtp) and reinforced with a bioactive filler, hydroxylapatite (SI-HADtp). The obtained mouldings were used to study the drug-release mechanisms from the plastic soy-TH matrixes. In an isotonic saline solution (ISS) buffered at pH 5.0 (200 mM acetate buffer), the resulting release kinetics could be described using the Fick's second law of diffusion. Because the diffusion coefficients were found to be constant and the boundary conditions to be stationary, these systems are drug-diffusion controlled. Conversely, the dominant phenomena in an isotonic saline solution buffered at pH 7.4 (200 mM Tris/HCl buffer) are more complex. In fact, because of the higher polymer solubility, the resulting matrix is time-variant. So, the drug release is affected by swelling, drug diffusion, and polymer dissolution, being faster when compared to ISS-200 mM acetate buffer, pH 5.0. The changes in the formulation composition affecting the correspondent release rates were also investigated. At pH 7.4, increasing the cross-linking degree of the polymer matrix (via reaction with glyoxal or heat treatment) or decreasing the net charge (extruding at pH near its isoelectric point) led to lower release rates. The incorporation of ceramic filler caused the opposite effect. Because of the low solubility of the matrix at pH 5.0, no significant variations were detected with variations in the selected formulations. These systems, based on a nonstandard protein-based material, seem to be very promising to be used as carriers for drug delivery.

The behavior of Aluminium Carbon/Epoxy fibre metal laminate under quasi-static loading

NASA Astrophysics Data System (ADS)

Romli, N. K.; Rejab, M. R. M.; Bachtiar, D.; Siregar, J.; Rani, M. F.; Harun, W. S. W.; Salleh, Salwani Mohd; Merzuki, M. N. M.

2017-10-01

One of major concerns that related to the flight safety is impact of birds. To minimize the risks, there is need to increase the impact resistance of aircraft by developing a new material and has the good structural design of aircraft structures. The hybrid laminates are potential candidate material to be applied for the aircraft structures susceptible to bird strikes. The fibre metal laminate was fabricated by a compression moulding technique. The carbon fibre and aluminium alloy 2024-0 was laminated by using thermoset epoxy. A compression moulding technique was used for the FML fabrication. The aluminium sheet metal has been roughening by a metal sanding method which to improve the bonding between the fibre and metal layer. The main objective of this paper is to determine the failure response of the laminate under five variations of the crosshead displacement in the quasi-static loading. The FML was modelled and analysed by using Explicit solver. Based on the experimental data of the quasi-static test, the result of 1 mm/min was 11.85 kN and higher than 5, 10, 50 and 100 mm/min which because of the aluminium ductility during the impact loading response. The numerical simulations were generally in good agreement with the experimental measurements.

Imide Oligomers Containing Pendent and Terminal Phenylethynyl Groups-2

NASA Technical Reports Server (NTRS)

Connell, J. W.; Smith, J. G., Jr.; Hergenrother, P. M.

1998-01-01

As part of a program to develop high-performance/high-temperature structural resins for aeronautical applications, imide oligomers containing pendent and terminal phenylethynyl groups were prepared, characterized and the cured resins evaluated as composite matrices. The oligomers were prepared at a calculated number-average molecular weight of 5000 g/mol and contained 15-20 mol% pendent phenylethynyl groups. In previous work, an oligomer containing pendent and terminal phenylethynyl groups exhibited a high glass transition temperature (approximately 313 C), and laminates therefrom exhibited high compressive properties, but processability, fracture toughness, microcrack resistance and damage tolerance were less than desired. In an attempt to improve these deficiencies, modifications in the oligomeric backbone involving the incorporation of 1,3-bis(3-aminophenoxy)benzene were investigated as a means of improving processability and toughness without detracting from the high glass transition temperature and high compressive properties. The amide acid oligomeric solutions were prepared in N-methyl-2-pyrrolidinone and were subsequently processed into imide powder, thin films, adhesive tape and carbon fiber prepreg. Neat resin plaques were fabricated from imide powder by compression moulding. The maximum processing pressure was 1.4 MPa and the cure temperature ranged from 350 to 371 C for 1 h for the mouldings, adhesives, films and composites. The properties of the 1,3-bis(3-aniinophenoxy)benzene modified cured imide oligomers containing pendent and terminal phenylethynyl groups are compared with those of previously prepared oligomers containing pendent and terminal phenylethynyl groups of similar composition and molecular weight.

Anti-Aspergillus activity of green coffee 5-O-caffeoyl quinic acid and its alkyl esters.

PubMed

Suárez-Quiroz, M L; Alonso Campos, A; Valerio Alfaro, G; González-Ríos, O; Villeneuve, P; Figueroa-Espinoza, M C

2013-01-01

The antifungal activities of 5-O-caffeoyl quinic acid (5-CQA) and of methyl, butyl, octyl, and dodecyl esters or 5-CQA, were tested on five toxigenic moulds from the Aspergillus genus (Aspergillus flavus, Aspergillus nomius, Aspergillus ochraceus, Aspergillus parasiticus, Aspergillus westerdijkiae). These mycotoxin producers' moulds may contaminate many types of food crops throughout the food chain posing serious health hazard to animals and humans. The use of chemical methods to decrease mycotoxin producer moulds contamination on food crops in the field, during storage, and/or during processing, has been proved to be efficient. In this work, the antifungal effect of 5-CQA and a homologous series of 5-CQA esters (methyl, butyl, octyl, dodecyl), was investigated using the microdilution method and the minimum inhibitory concentrations (MIC50 and MIC80). All molecules presented antifungal activity, and two esters showed a MIC for all fungi: octyl (MIC50 ≤ 0.5-0.75 mg/mL, MIC80 = 1.0-1.5 mg/mL) and dodecyl (MIC50 = 0.75-1.25 mg/mL) chlorogenates. Dodecyl chlorogenate showed a MIC80 (1.5 mg/mL) only for A. parasiticus. The maximum percent of growth inhibition on aspergillii was observed with octyl (78.4-92.7%) and dodecyl (54.5-83.7%) chlorogenates, being octyl chlorogenate the most potent antifungal agent. It was thus concluded that lipophilization improved the antifungal properties of 5-CQA, which increased with the ester alkyl chain length, exhibiting a cut-off effect at 8 carbons. As far as we know, it is the first report demonstrating that lipophilization may improve the antifungal activity of 5-CQA on five toxigenic moulds from the Aspergillus genus. Lipophilization would be a novel way to synthesize a new kind of antifungal agents with a good therapeutic value or a potential use as preservative in food or cosmetics. Copyright © 2013 Elsevier Ltd. All rights reserved.

Shelf life extension of pre-baked buns by an ACTIVE PACKAGING ethanol emitter.

PubMed

Franke, I; Wijma, E; Bouma, K

2002-03-01

The paper reports the influence of an ethanol emitter (Ethicap) on the microbiological condition and the shelf life extension of a bakery product. Pre-baked buns, with a water activity of 0.95, were packaged with different amounts of Ethicap and stored at room temperature. Yeasts and moulds remained largely absent from the core of the pre-baked bun (< 10(2) cfu g(-1)) during storage, independent of the presence of ethanol. The total mesophilic count was low at the beginning of the storage experiment (< 10(2) cfu g(-1)), but increased without ethanol within 1 week to an unacceptable level. In the presence of ethanol, the total mesophilic count stabilizes at a consumable level of 10(5)-10(6) cfu g(-1). The increase of total mesophilic count was caused by growth of a Bacillus spp., probably B. subtilis. Mould growth on the outer surface is limiting for shelf life extension. On the pre-baked buns, the following moulds were present: Penicillium solitum, P. commune, P. corylophilum, Cladosporium sphaerospermum and C. herbarum. These started to grow within 4-6 days. Mould growth can be delayed for 13 days by adding Ethicap. The ethanol probably has to be absorbed by the pre-baked bun to be effective in growth suppression of the Bacillus spp. the moulds. The pre-baked buns absorb most of the ethanol from the package headspace, and the ethanol content of the products is approximately 0.8 weight% after 21 days. This largely exceeds the overall migration limit of 60 mg kg(-1) food (0.006 weight%).

Evaluation of Three MALDI-TOF Mass Spectrometry Libraries for the Identification of Filamentous Fungi in Three Clinical Microbiology Laboratories in Manitoba, Canada.

PubMed

Stein, Markus; Tran, Vanessa; Nichol, Kimberly A; Lagacé-Wiens, Philippe; Pieroni, Peter; Adam, Heather J; Turenne, Christine; Walkty, Andrew J; Normand, Anne-Cécile; Hendrickx, Marijke; Piarroux, Renaud; Karlowsky, James A

2018-06-12

Matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) is commonly used by clinical microbiology laboratories to identify bacterial pathogens and yeasts, but not for the identification of moulds. Recent progress in extraction protocols and the composition of comparative libraries support potential application of MALDI-TOF MS for mould identification in clinical microbiology laboratories. We evaluated the performance of the Bruker Microflex ™ MALDI-TOF MS instrument (Billerica, MA, USA) to identify clinical isolates and reference strains of moulds using three libraries, the Bruker mould library, the National Institutes of Health (NIH) library, and the Mass Spectrometry Identification (MSI) online library, and compared those results to conventional (morphological) and molecular (18S/ITS; gold standard) identification methods. All three libraries demonstrated greater accuracy in genus identification (≥94.9%) than conventional methods (86.4%). MALDI-TOF MS identified 73.3% of isolates to species-level compared to only 31.7% by conventional methods. The MSI library demonstrated the highest rate of species-level identification (72.0%) compared to NIH (19.5%) and Bruker (13.6%) libraries. Greater than 20% of moulds remained unidentified to species-level by all three MALDI-TOF MS libraries primarily because of library limitations or imperfect spectra. The overall identification rate of each MALDI-TOF MS library depended on the number of species and the number of spectra representing each species in the library. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Wood working: planing and moulding in the last frontier

Treesearch

David Nicholls

2007-01-01

Planing and moulding is an important step in the value-added manufacture of wood products, and recent advances in Alaska have been noteworthy. Just a few years ago, most planing occurred on simple shop planers, producing lumber for retail sale or for wood working uses such as cabinet stock. Currently there are at least 26 planers and 13 moulders in-production at...

Prevalence of Penicillium specific Ig E level and allergy symptoms among office workers in a selected company in Bangi, Malaysia.

PubMed

Goh, J C C; Juliana, J; Malina, O; Ngah, Z U; Norhafizalena, O

2007-06-01

Indoor fungal reservoirs, particularly airborne Penicillium species, were identified throughout the ventilation system of the building and dissemination of fungi from those reservoirs was found to be occurring all the time. The objectives of this study were to determine the association between air concentration of indoor mould (Penicillium) and allergy symptoms among office workers. The study design used in this research was a cross-sectional study. Risk factors were identified through the questionnaire survey. Office workers were selected based on the proximity of their workstations to the microbiological air sampler used for the mould sampling. Results from the current study suggests that individual susceptibility of exposed subjects might be influenced by several factors associated with mould exposure; for example, inhaled mycotoxins or volatile organic compounds, which may, in some complex way, affect the immune response. This study provides the much needed preliminary baseline data for developing guidelines with validated findings that will be of use for policy decisions in Malaysia regarding indoor air quality. Results from this study are recommended for use in planning and implementing control measures in order to reduce the exposure to indoor mould and promote healthy working environment among the workers.

The contribution of moulds and yeasts to the fermentation of 'agbelima' cassava dough.

PubMed

Amoa-Awua, W K; Frisvad, J C; Sefa-Dedeh, S; Jakobsen, M

1997-09-01

Agbelima, a fermented cassava meal widely consumed in Ghana, Togo and Benin, is produced by fermenting grated cassava with one of several types of traditional cassava dough inoculum. During fermentation a smooth textured sour dough is produced, the toxicity of cassava is reduced and there is a build up of volatile aroma compounds. Four types of inocula were included in the present investigation. In one type moulds were found to form a dominant part of the microbiota, the species present being Penicillium sclerotiorum, P. citrinum, P. nodulum, Geotrichum candidum and a basidiomycete. All these moulds were found to possess cellulase activity which was responsible for the hydrolysis of cassava tuber cellulose during fermentation leading to a breakdown of the coarse texture of cassava dough. The yeasts Candida krusei, C. tropicalis and Zygosaccharomyces spp. were present in high numbers in the four types of inocula including the moudly inoculum. The yeasts C. tropicalis and some strains of Zygosaccharomyces, all of which possessed cellulase activity, were also found to contribute to the modification of cassava texture during fermentation. All yeasts and moulds exhibited linamarase activity and were therefore capable of breaking down the cyanogenic glucosides present in cassava.

Free flow isotachophoresis in an injection moulded miniaturised separation chamber with integrated electrodes.

PubMed

Stone, Victoria N; Baldock, Sara J; Croasdell, Laura A; Dillon, Leonard A; Fielden, Peter R; Goddard, Nick J; Thomas, C L Paul; Treves Brown, Bernard J

2007-07-06

An injection moulded free flow isotachophoresis (FFITP) microdevice with integrated carbon fibre loaded electrodes with a separation chamber of 36.4mm wide, 28.7 mm long and 100 microm deep is presented. The microdevice was completely fabricated by injection moulding in carbon fibre loaded polystyrene for the electrodes and crystal polystyrene for the remainder of the chip and was bonded together using ultrasonic welding. Two injection moulded electrode designs were compared, one with the electrode surface level with the separation chamber and one with a recessed electrode. Separations of two anionic dyes, 0.2mM each of amaranth and acid green and separations of 0.2mM each of amaranth, bromophenol blue and glutamate were performed on the microdevice. Flow rates of 1.25 ml min(-1) for the leading and terminating electrolytes were used and a flow rate of 0.63 ml min(-1) for the sample. Electric fields of up to 370 V cm(-1) were applied across the separation chamber. Joule heating was not found to be significant although out-gassing was observed at drive currents greater than 3 mA.

Bacteria, mould and yeast spore inactivation studies by scanning electron microscope observations.

PubMed

Rozali, Siti N M; Milani, Elham A; Deed, Rebecca C; Silva, Filipa V M

2017-12-18

Spores are the most resistant form of microbial cells, thus difficult to inactivate. The pathogenic or food spoilage effects of certain spore-forming microorganisms have been the primary basis of sterilization and pasteurization processes. Thermal sterilization is the most common method to inactivate spores present on medical equipment and foods. High pressure processing (HPP) is an emerging and commercial non-thermal food pasteurization technique. Although previous studies demonstrated the effectiveness of thermal and non-thermal spore inactivation, the in-depth mechanisms of spore inactivation are as yet unclear. Live and dead forms of two food spoilage bacteria, a mould and a yeast were examined using scanning electron microscopy before and after the inactivation treatment. Alicyclobacillus acidoterrestris and Geobacillus stearothermophilus bacteria are indicators of acidic foods pasteurization and sterilization processes, respectively. Neosartorya fischeri is a phyto-pathogenic mould attacking fruits. Saccharomyces cerevisiae is a yeast with various applications for winemaking, brewing, baking and the production of biofuel from crops (e.g. sugar cane). Spores of the four microbial species were thermally inactivated. Spores of S. cerevisiae were observed in the ascus and free form after thermal and HPP treatments. Different forms of damage and cell destruction were observed for each microbial spore. Thermal treatment inactivated bacterial spores of A. acidoterrestris and G. stearothermophilus by attacking the inner core of the spore. The heat first altered the membrane permeability allowing the release of intracellular components. Subsequently, hydration of spores, physicochemical modifications of proteins, flattening and formation of indentations occurred, with subsequent spore death. Regarding N. fischeri, thermal inactivation caused cell destruction and leakage of intracellular components. Both thermal and HPP treatments of S. cerevisiae free spores attacked the inner membrane, altering its permeability, and allowing in final stages the transfer of intracellular components to the outside. The spore destruction caused by thermal treatment was more severe than HPP, as HPP had less effect on the spore core. All injured spores have undergone irreversible volume and shape changes. While some of the leakage of spore contents is visible around the deformed but fully shaped spore, other spores exhibited large indentations and were completely deformed, apparently without any contents inside. This current study contributed to the understanding of spore inactivation by thermal and non-thermal processes. Copyright © 2017 Elsevier B.V. All rights reserved.

Injection moulding of plastic parts with laser textured surfaces with optical applications

NASA Astrophysics Data System (ADS)

Pina-Estany, J.; García-Granada, A. A.; Corull-Massana, E.

2018-05-01

The purpose of this work is to manufacture micro and nanotextured surfaces on plastic injection moulds with the aim of replicating them and obtaining plastic parts with optical applications. Different patterns are manufactured with nanosecond and femtosecond lasers in order to obtain three different optical applications: (i) homogeneous light diffusion (ii) 1D light directionality and (iii) 2D light directionality. Induction heating is used in the injections in order to improve the textures degree of replication. The steel mould and the plastic parts are analyzed with a confocal/focus variation microscope and with a surface roughness tester. A mock-up and a luminance camera are used to evaluate the homogeneity and luminance of the homogeneous light diffusion application in comparison with the current industrial solutions.

Modelling the drying of three-dimensional pulp moulded structures. Part II, Drying data obtained from flat panels using virgin and recycled paper fibre

Treesearch

John F. Hunt; Margit Tamasy-Bano; Heike Nyist

1999-01-01

A three-dimensional structural panel, called FPL Spaceboard, was developed at the USDA Forest Products Laboratory. Spaceboard panels have been formed using a variety of fibrous materials using either a wet- or dry-forming process. Geometrically, the panel departs from the traditional two-dimensional flat panel by integrally forming an array of perpendicular ribs and...

3D printed facial laser scans for the production of localised radiotherapy treatment masks - A case study.

PubMed

Briggs, Matthew; Clements, Helen; Wynne, Neil; Rennie, Allan; Kellett, Darren

This study investigates the use of 3D printing for patients that require localised radiotherapy treatment to the face. The current process involves producing a lead mask in order to protect the healthy tissue from the effects of the radiotherapy. The mask is produced by applying a thermoplastic sheet to the patient's face and allowing to set hard. This can then be used as a mould to create a plaster impression of the patient's face. A sheet of lead is then hammered on to the plaster to create a bespoke fitted face mask. This process can be distressing for patients and can be problematic when the patient is required to remain motionless for a prolonged time while the thermoplastic sets. In this study, a 1:1 scale 3D print of a patient's face was generated using a laser scanner. The lead was hammered directly on to the surface of the 3D print in order to create a bespoke fitted treatment mask. This eliminated the thermoplastic moulding stage and significantly reduced the time needed for the patient to be in clinic. The higher definition impression of the the face resulted in a more accurate, better fitting treatment mask.

Optimization of Recycled Glass Fibre-Reinforced Plastics Gear via Integration of the Taguchi Method and Grey Relational Analysis

NASA Astrophysics Data System (ADS)

Mizamzul Mehat, Nik; Syuhada Zakarria, Noor; Kamaruddin, Shahrul

2018-03-01

The increase in demand for industrial gears has resulted in the increase in usage of plastic-matrix composites particularly glass fibre-reinforced plastics as the gear materials. The usage of these synthetic fibers is to enhance the mechanical strength and the thermal resistance of the plastic gears. Nevertheless, the production of large quantities of these synthetic fibre-reinforced composites poses a serious threat to the ecosystem. Comprehending to this fact, the present work aimed at investigating the effects of incorporating recycled glass fibre-reinforced plastics in various compositions particularly on dimensional stability and mechanical properties of gear produced with diverse injection moulding processing parameters setting. The integration of Grey relational analysis (GRA) and Taguchi method was adopted to evaluate the influence of recycled glass fibre-reinforced plastics and variation in processing parameters on gear quality. From the experimental results, the blending ratio was found as the most influential parameter of 56.0% contribution in both improving tensile properties as well as in minimizing shrinkage, followed by mould temperature of 24.1% contribution and cooling time of 10.6% contribution. The results obtained from the aforementioned work are expected to contribute to accessing the feasibility of using recycled glass fibre-reinforced plastics especially for gear application.

Assessing market-sold remedies in lomé (togo) for hygienic quality.

PubMed

de Souza, Comlan; Ameyapoh, Yaovi; Karou, Simplice D; Anani, Kokou T; Kpodar, Madje L; Gbeassor, Mensavi

2011-01-01

Traditional concoctions sold in marketplaces are always assumed to be safe and efficient; however, they can be potentially toxic because of poor hygienic practices in plant processing or storage. The present study aimed to assess for the microbial quality of market-sold vegetable drugs in Lomé. Thus, a total of 209 plant remedies were collected in marketplaces and analysed for the presence of total aerobic bacteria, total coliforms, thermotolerant coliforms, Staphylococcus aureus, sulphite reducing bacteria, and yeast and moulds according to the French Association of Normalisation (AFNOR) guidelines. The results revealed that all formulations were contaminated by several microorganisms, excepted alcohol-based mixtures. According to AFNOR limits nonconform drugs were according to total aerobic bacteria (86.96% powders, 81.82% capsules, 66.67% tisanes, and 42.11% decoctions); to total coliforms (9.10% capsules, 8.70% powders and 1.75% decoction); to yeasts and moulds (77.78% ointments, 40% calcined powders, 36.36% capsules, and 23.91% powders). The microbiological analysis revealed that the majority of contaminating bacteria were gram positive catalase positive and oxidase positive bacilli. Quality control studies on market-sold remedies are currently needed to evaluate the microbial risk in consuming these products and they may allow the standardisation of plant processing and storage.

Assessing Market-Sold Remedies in Lomé (Togo) for Hygienic Quality

PubMed Central

de Souza, Comlan; Ameyapoh, Yaovi; Karou, Simplice D.; Anani, Kokou T.; Kpodar, Madje L.; Gbeassor, Mensavi

2011-01-01

Traditional concoctions sold in marketplaces are always assumed to be safe and efficient; however, they can be potentially toxic because of poor hygienic practices in plant processing or storage. The present study aimed to assess for the microbial quality of market-sold vegetable drugs in Lomé. Thus, a total of 209 plant remedies were collected in marketplaces and analysed for the presence of total aerobic bacteria, total coliforms, thermotolerant coliforms, Staphylococcus aureus, sulphite reducing bacteria, and yeast and moulds according to the French Association of Normalisation (AFNOR) guidelines. The results revealed that all formulations were contaminated by several microorganisms, excepted alcohol-based mixtures. According to AFNOR limits nonconform drugs were according to total aerobic bacteria (86.96% powders, 81.82% capsules, 66.67% tisanes, and 42.11% decoctions); to total coliforms (9.10% capsules, 8.70% powders and 1.75% decoction); to yeasts and moulds (77.78% ointments, 40% calcined powders, 36.36% capsules, and 23.91% powders). The microbiological analysis revealed that the majority of contaminating bacteria were gram positive catalase positive and oxidase positive bacilli. Quality control studies on market-sold remedies are currently needed to evaluate the microbial risk in consuming these products and they may allow the standardisation of plant processing and storage. PMID:21350662

Multi-Scale Modeling of an Integrated 3D Braided Composite with Applications to Helicopter Arm

NASA Astrophysics Data System (ADS)

Zhang, Diantang; Chen, Li; Sun, Ying; Zhang, Yifan; Qian, Kun

2017-10-01

A study is conducted with the aim of developing multi-scale analytical method for designing the composite helicopter arm with three-dimensional (3D) five-directional braided structure. Based on the analysis of 3D braided microstructure, the multi-scale finite element modeling is developed. Finite element analysis on the load capacity of 3D five-directional braided composites helicopter arm is carried out using the software ABAQUS/Standard. The influences of the braiding angle and loading condition on the stress and strain distribution of the helicopter arm are simulated. The results show that the proposed multi-scale method is capable of accurately predicting the mechanical properties of 3D braided composites, validated by the comparison the stress-strain curves of meso-scale RVCs. Furthermore, it is found that the braiding angle is an important factor affecting the mechanical properties of 3D five-directional braided composite helicopter arm. Based on the optimized structure parameters, the nearly net-shaped composite helicopter arm is fabricated using a novel resin transfer mould (RTM) process.

Finite Element Simulation of Aluminium/GFRP Fibre Metal Laminate under Tensile Loading

NASA Astrophysics Data System (ADS)

Merzuki, M. N. M.; Rejab, M. R. M.; Romli, N. K.; Bachtiar, D.; Siregar, J.; Rani, M. F.; Salleh, Salwani Mohd

2018-03-01

The response of a fibre metal laminate (FML) model to the tensile loading is predicted through a computational approach. The FML consisted with layers of aluminum alloy and embedded with one layer of composite material, Glass fibre Reinforced Plastic (GFRP). The glass fibre and aluminium alloy 2024-0 was laminated by using thermoset epoxy. A compression moulding technique was used in the process of a FML fabrication. The aluminium has been roughen by a metal sanding method which to improve the bonding between the fibre and metal layer. The main objective of this paper is to determine the failure behaviour of the FML under the tensile loading. The responses on the FML under the tensile loading were numerically performed. The FML was modelled and analysed by using Abaqus/CAE 6.13 version. Based on the experimental and FE data of the tensile, the ultimate tensile stress is 120 MPa where delamination and fibre breakage happened. A numerical model was developed and agreed well with the experimental results. The laminate has an inelastic respond to increase the tensile loads which due to the plasticity of the aluminium layers.

Study on the mould-resistant properties of moso bamboo treated with high pressure and amylase

Treesearch

Xiao-Dong Huang; Chung-Yun Hse; Todd F. Shupe

2014-01-01

Starch of moso bamboo mainly exists in the elongated parenchyma cells, and it is difficult for amylase to enter moso bamboo and dissolve the starch. Therefore, the mould resistance capability of moso bamboo's products cannot meet the need for bamboo to resist fungal decay. In this experiment, moso bamboo blocks were first treated at six levels of pressure and for...

Integrated Protection Against Lyctid Beetle Infestations Part II. - Laboratory Dip-Diffusion Treatment of Unseasoned Banak (Virola spp.) Lumber with Boron Compounds

Treesearch

Lonnie H. Williams; Joe K. Mauldin

1985-01-01

A manufacturer of conventional moulding wanted a method that would prevent lyctid beetle damage to banak (Virola spp.) wood throughout the period from initial cutting in Brazil until final mouldings were in use. Because complete penetration of wood may be obtained, unseasoned banak wood was treated by dip-diffusion with disodium octaborate...

Environmental analysis of waste foundry sand via life cycle assessment.

PubMed

Mitterpach, Jozef; Hroncová, Emília; Ladomerský, Juraj; Balco, Karol

2017-01-01

The aim of this manuscript is to provide an environmental assessment of the creation and use of waste foundry sand (WFS) via an LCA in a foundry for grey cast iron. A life cycle impact assessment was carried out using SimaPro 8. This environmental analysis assessed the impact of creating waste foundry sand (WFS) in a foundry, Hronec (Slovakia, Central Europe). According to BREF, this foundry is classified as an iron foundry with a production capacity greater than 20 t/day with processes typical for grey cast iron foundries. Molten metal is poured into single-use sand moulds. We identified those factors influencing the creation and use of WFS which significantly affect the quality of the environment. The use of WFS from the production of cores in regenerated moulding mixtures with installed circuits brings marked minimisation of material and energy inputs in the processes of creating WFS and it positively influences the consumption of resources and the quality of the ecosystem. Space for lessening the impact of WFS processes upon the consumption of resources and ecosystem quality is mainly found in recycling WFS in the building sector. In the next step, it is necessary to thoroughly verify the eco-toxicological properties of not only the created WFS and other foundry waste, but mainly the building products for which this waste is used. In terms of transportation, it is important that waste is recycled at local level. The processes of creating WFS have a marked influence upon all the selected waste categories (consumption of resources, ecosystem quality, human health). By minimising material inputs into processes and the effective adjustment of production technology, a foundry can significantly lessen the impacts of processes for creating WFS upon the environment.

Thermo-rheological behaviour of polymer melts in microinjection moulding

NASA Astrophysics Data System (ADS)

Vasco, J. C.; Maia, J. M.; Pouzada, A. S.

2009-10-01

Microinjection has proven to be one of the most efficient replication methods for microcomponents and microsystems in various domains of microengineering. The use of available commercial microinjection equipment to evaluate the polymeric flow in microchannels would surely contribute to enhancing knowledge on polymeric flow at the microscale under industrial conditions. This approach is appropriate since rheological phenomena such as wall slip, surface tension, melt pressure drop and polymer flow length can be studied. These aspects are not fully dealt with in current commercial simulation software packages. In this study a micromould was designed to assess and characterize the flow in microchannels under realistic industrial conditions.

Determination of irritant threshold concentrations of multiple tree, grass, weed and mould allergens for intradermal testing of horses residing in the southern USA.

PubMed

Lane, Martha J; Pucheu-Haston, Cherie M; Kearney, Michael T; Woodward, Michelle

2017-12-01

Appropriate allergen threshold concentrations (TCs) for intradermal testing (IDT) have not been established in horses for many pollen and mould allergens. To determine the TCs in non-allergic horses and describe the frequency of late phase reactions for 26 allergens, including trees, grasses, weeds and moulds in horses residing in the southern Unites States. Twenty four clinically normal horses in the southern United States. Threshold concentrations for different allergens were determined using IDT subjective measurements at 30 minutes. Delayed reactions were evaluated at 4 and 24 h. Threshold concentrations (all PNU/mL) were established for eight tree allergens (black willow 1,000, box elder 1,000, live oak 1,000, pecan 2,000, white ash 4,000, red oak 4,000, red mulberry 2,000 and green ash 2,000); two grass allergens (Johnson grass 250 PNU/mL and Kentucky blue grass 500 PNU/mL); two weeds (carelessweed 1,000 PNU/mL, great ragweed 500 PNU/mL) and one mould (Curvularia 8,000 PNU/mL). The TC was not determined due to excessive reactivity at the lowest concentration tested (1,000 PNU/mL) for bahia and perennial rye grass. Eleven other allergens did not meet the criteria to establish a TC when evaluated at 30 min due to lack of positive reactions. Multiple allergens caused positive reactions in ≥10% of horses at 4 h. Reactions at 24 h were rare with the exception of one horse. This study identified intradermal TC for multiple pollen and mould allergens in horses. These values may prove useful for optimizing allergen concentrations for IDT of allergic horses. © 2017 ESVD and ACVD.

Aeroallergen and food IgE sensitization and local and systemic inflammation in asthma.

PubMed

Patelis, A; Janson, C; Borres, M P; Nordvall, L; Alving, K; Malinovschi, A

2014-03-01

We recently reported an independent association between IgE sensitization to food allergens and increased airway inflammation, assessed by fraction of exhaled nitric oxide (FeNO), in a population-based study (J Allergy Clin Immunol, 130, 2012, 397). Similar studies have not been performed in populations with asthma. The aim of the present study was to investigate the allergic sensitization profile in asthmatics and examine FeNO, airway responsiveness and blood eosinophilia in relation to type and degree of IgE sensitization. FeNO, airway responsiveness, blood eosinophil count (B-Eos) and IgE sensitization to food allergens and aeroallergens were determined in 408 subjects with asthma, aged 10-34 years. Asthmatics had higher prevalence of IgE sensitization against all allergens than controls (P < 0.001). Mite, pollen, furry animal, mould and food sensitizations were each associated with increased FeNO, airway responsiveness and B-Eos in asthmatics. IgE sensitization to mould, furry animals and food allergens was independently related to FeNO (all P < 0.05) after adjustment for age, sex, height, smoking history and medication. IgE sensitization to mould (P < 0.001) and furry animals (P = 0.02) was related to airway responsiveness in a similar model. Finally, IgE sensitization to mould (P = 0.001), furry animals (P < 0.001) and food allergens (P < 0.001) was independently related to B-Eos. Independent effects of IgE sensitization to aeroallergens (furry animals and mould) and food allergens were found on both local and systemic markers of inflammation in asthma. The finding regarding food IgE sensitization is novel, and a clinical implication might be that even food sensitization must be assessed to fully understand inflammation patterns in asthma. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

[Effects of 33% grapefruit extract on the growth of the yeast--like fungi, dermatopytes and moulds].

PubMed

Krajewska-Kułak, E; Lukaszuk, C; Niczyporuk, W

2001-01-01

Grapefruit seed extract was discovered by Jacob Harich an american immunologist in 1980. Assessment of the influence of grapefruit extract on the yeast-like fungi strains--Candida albicans growth. Material used in this investigation was ATCC test Candida albicans strains no 10231, 200 of Candida albicans strains, 5 of Candida sp. strains isolated from patients with candidiasis symptoms from different ontocenosis and 12 of dermatophytes and moulds isolated from patients. The susceptibility of the Candida was determined by serial dilution method. It seems that 33% grapefruit extract exert a potent antifungal activity against the yeast like fungi strains and had low activity against dermatophytes and moulds. Further studies in vitro and in vivo on greater number of the yeast-like fungi strains and other fungi species are needed.

[Invasive mould disease in haematological patients].

PubMed

Ruiz-Camps, Isabel; Jarque, Isidro

2014-01-01

Invasive mould infections (IMI) are a persistent problem with high morbidity and mortality rates among patients receiving chemotherapy for hematological malignancies and hematopoietic stem cell transplant recipients. Management of IMI in this setting has become increasingly complex with the advent of new antifungal agents and diagnostic tests, which have resulted in different therapeutic strategies (prophylactic, empirical, pre-emptive, and directed). A proper assessment of the individual risk for IMI appears to be critical in order to use the best prophylactic and therapeutic approach and increase the survival rates. Among the available antifungal drugs, the most frequently used in the hematologic patient are fluconazole, mould-active azoles (itraconazole, posaconazole and voriconazole), candins (anidulafungin, caspofungin and micafungin), and lipid formulations of amphotericin B. Specific recommendations for their use, and criteria for selecting the antifungal agents are discussed in this paper. Copyright © 2014. Published by Elsevier Espana.

USSR Report Agriculture.

DTIC Science & Technology

1986-03-04

per hectare) is employed against snow mould in the autumn and Bayleton (0.5 kg) is used upon the appearance of powdery mildew , brown rust and root rots...mould in the autumn and Bayleton (0.5 kg) is used upon the appearance of powdery mildew , brown rust and root rots prior to the forming of the grain. At...33 Fallow as Wheat Predecessor Stressed for Kazakhstan (A. Zadorin, L. Mozhayev; SELSKOYE KHOZYAYSTVO KAZAKHSTANA

Test of cold asphalt storability based on alternative approaches

NASA Astrophysics Data System (ADS)

Abaffyová, Zora; Komačka, Jozef

2017-09-01

Cold asphalt products for potholes repairs should be workable (soft enough) for long time to ensure their applicability. Storability is assessed indirectly using various tests of workability. Therefore, simple test methods (self-compaction and disintegration test) was developed and verified to investigate changes of storability of this group of cold asphalts. Selfcompaction of the tested mixture in the upturned Abram’s cone for the cement concrete slump test and in the mould for the California Bearing Ratio test was assessed in first stage. After that the video record of disintegration test was taken. During this test, the mould was lifted up and the mixture fell off the mould (Abram’s cone) or disintegrate (CBR mould). The drop of surface after 10 min self-compaction and netto time related to falling out or disintegration of the mixture were used to evaluate the mixture from storability point of view. It was found out the self-compaction test has not a potential to reveal and prove changes of mixture properties. Based on the disintegration test results it can be stated this test at 5 °C using the upturned Abram’s cone could be a suitable approach to determine qualitative changes of a cold mixture from storability point of view.

Effects of fungal deterioration on grain: nutritional value, toxicity, germination.

PubMed

Sauer, D B

1988-12-01

Moulds or fungi that grow in grains and seeds during storage and transport cause germination decrease, visible mouldiness, discoloration, musty or sour odours, caking, chemical and nutritional changes, reduction in processing quality, and form of mycotoxins. These deteriorative changes affect the grade and price of grain and contribute to customer dissatisfaction when the grain is marketed. The respiration of grain and fungi results in a loss in dry matter as well as the production of heat and moisture which contribute to further spoilage. Net changes in nutritional value and the risk of mycotoxin contamination are difficult to predict because they depend on a complex interaction of factors such as temperature, moisture, storage time, fungal species composition, kind of grain, and previous storage history. Moisture is the most important variable determining the rate of deterioration caused by fungi, with temperature being the second major factor. Problems with deterioration of grain in export shipments are not a recent development. They are related primarily to grain moisture at loading, and also to the extent of previous mould invasion.

Analysis of surface scale on the Ni-based superalloy CMSX-10N and proposed mechanism of formation

NASA Astrophysics Data System (ADS)

Simmonds, S.; D'Souza, N.; Ryder, K. S.; Dong, H.

2012-01-01

There is a continuing demand to raise the operating temperature of jet engine turbine blades to meet the need for higher turbine entry temperatures (TET) in order to increase thermal efficiency and thrust. Modern, high-pressure turbine blades are made from Ni-based superalloys in single-crystal form via the investment casting process. One important post-cast surface defect, known as 'surface scale', has been investigated on the alloy CMSX-10N. This is an area of distinct discolouration of the aerofoil seen after casting. Auger electron and X-ray photoelectron spectroscopy analysis were carried out on both scaled and un-scaled areas. In the scaled region, a thin layer (~800nm) of Ni oxide is evident. In the un-scaled regions there is a thicker Al2O3 layer. It is shown that, as the blade cools during casting, differential thermal contraction of mould and alloy causes the solid blade to 'detach' from the mould in these scaled areas. The formation of Ni Oxides is facilitated by this separation.

A bio-material: mechanical behaviour of LDPE-Al2O3-TiO2

NASA Astrophysics Data System (ADS)

Dhabale, R.; Jatti, V. S.

2016-09-01

Polymer composites are prominent candidate for polymeric bio-composites due to its low cost, high strength and ease of manufacturing. However, they suffer from low mechanical properties such as high wear rate and low hardness. In view of this, present study focuses on the synthesis of hybrid bio polymer matrix composites using low density polyethylene as matrix material with reinforcing material namely, alumina and titanium oxide. The samples were fabricated as per ASTM standard by varying the percentage of reinforcing particles using injection moulding machine. Various tests namely, tensile, flexural, impact, hardness, wear, SEM and corrosion were conducted on the prepared samples. On the basis of the experimental results, it can be concluded that injection moulding process can fabricate defect free cast samples. Polymer matrix composites of 70%LDPE +10% TiO2 +20% Al2O3 composition is biocompatible and a good candidate for biomaterial. Thus based on the inference of this study the above polymer matrix composite is suitable for orthopaedic applications and can be applied on hard and soft tissues of implantable materials in a human body.

Hybrid histidine kinases in pathogenic fungi.

PubMed

Defosse, Tatiana A; Sharma, Anupam; Mondal, Alok K; Dugé de Bernonville, Thomas; Latgé, Jean-Paul; Calderone, Richard; Giglioli-Guivarc'h, Nathalie; Courdavault, Vincent; Clastre, Marc; Papon, Nicolas

2015-03-01

Histidine kinases (HK) sense and transduce via phosphorylation events many intra- and extracellular signals in bacteria, archaea, slime moulds and plants. HK are also widespread in the fungal kingdom, but their precise roles in the regulation of physiological processes remain largely obscure. Expanding genomic resources have recently given the opportunity to identify uncharacterised HK family members in yeasts and moulds and now allow proposing a complex classification of Basidiomycota, Ascomycota and lower fungi HK. A growing number of genetic approaches have progressively provided new insight into the role of several groups of HK in prominent fungal pathogens. In particular, a series of studies have revealed that members of group III HK, which occur in the highest number of fungal species and contain a unique N-terminus region consisting of multiple HAMP domain repeats, regulate morphogenesis and virulence in various human, plant and insect pathogenic fungi. This research field is further supported by recent shape-function studies providing clear correlation between structural properties and signalling states in group III HK. Since HK are absent in mammals, these represent interesting fungal target for the discovery of new antifungal drugs. © 2015 John Wiley & Sons Ltd.

Comparison of impact strength of acrylic resin reinforced with kevlar and polyethylene fibres.

PubMed

Kamath, G; Bhargava, K

2002-01-01

The present study was done to evaluate the impact strengths of heat-activated acrylic resins reinforced with Kevlar fibres, polyethylene fibres and unreinforced heat activated acrylic resin. Each of three groups had 25 specimens. Brass rods of uniform length of 40 mm and diameter of 8 mm were used to prepare the moulds. A combination of long fibres (40 mm length) and short fibres (6 mm length) were used. The total amount of fibres incorporated was limited to 2% by weight of the resin matrix. Short and long fibres of equal weight were incorporated. The short fibres were mixed with polymer and monomer and packed into the mould, while, the long axis of the specimen, perpendicular to the applied force. The specimens were then processed. Impact strength testing was done on Hounsfield's impact testing machine. Kevlar fibre reinforced heat activated acrylic resin specimens recorded higher mean impact strength of 0.8464 Joules, while polyethylene fibres reinforced heat activated acrylic resin recorded mean impact strength of 0.7596 joules. The unreinforced heat activated acrylic resin recorded mean impact strength of 0.3440 Joules.

Collective irrationality and positive feedback.

PubMed

Nicolis, Stamatios C; Zabzina, Natalia; Latty, Tanya; Sumpter, David J T

2011-04-26

Recent experiments on ants and slime moulds have assessed the degree to which they make rational decisions when presented with a number of alternative food sources or shelter. Ants and slime moulds are just two examples of a wide range of species and biological processes that use positive feedback mechanisms to reach decisions. Here we use a generic, experimentally validated model of positive feedback between group members to show that the probability of taking the best of options depends crucially on the strength of feedback. We show how the probability of choosing the best option can be maximized by applying an optimal feedback strength. Importantly, this optimal value depends on the number of options, so that when we change the number of options the preference of the group changes, producing apparent "irrationalities". We thus reinterpret the idea that collectives show "rational" or "irrational" preferences as being a necessary consequence of the use of positive feedback. We argue that positive feedback is a heuristic which often produces fast and accurate group decision-making, but is always susceptible to apparent irrationality when studied under particular experimental conditions.

Fumigation success for California facility.

PubMed

Hacker, Robert

2010-02-01

As Robert Hacker, at the time director of facilities management at the St John's Regional Medical Center in Oxnard, California, explains, the hospital, one of the area's largest, recently successfully utilised a new technology to eliminate mould, selecting a cost and time-saving fumigation process in place of the traditional "rip and tear" method. Although hospital managers knew the technology had been used extremely effectively in other US buildings, this was reportedly among the first ever healthcare applications.

Surface microstructuring of biocompatible bone analogue material HAPEX using LIGA technique and embossing

NASA Astrophysics Data System (ADS)

Schneider, Andreas; Rea, Susan; Huq, Ejaz; Bonfield, William

2003-04-01

HAPEX is an artificial bone analogue composite based on hydroxyapatite and polyethylene, which can be applied for growth of bone cells. Due to its biocompatibility and favourable mechanical properties, HAPEX is used for orthopaedic implants like tympanic (middle ear) bones. The morphology of HAPEX surfaces is of high interest and it is believed that surface structuring on a micron scale might improve the growth conditions for bone cells. A new and simple approach for the microstructuring of HAPEX surfaces has been investigated using LIGA technique. LIGA is a combination of several processes, in particular lithography, electroplating and forming/moulding. For HAPEX surface structuring, arrays of dots, grids and lines with typical lateral dimension ranging from 5 μm to 50 μm were created on a chromium photomask and the patterns were transferred into thick SU-8 photoresist (structure height > 10 μm) by UV lithography. Subsequently, the SU-8 structures served as moulds for electroplating nickel on Si wafers and nickel substrates. The final nickel microstructures were used as embossing master for the HAPEX material. Embossing was carried out using a conventional press (> 500 hPa) with the facility to heat the master and the HAPEX. The temperature ranged from ambient to a few degrees above glass transition temperature (Tg) of HAPEX. The paper will include details of the fabrication process and process tolerances in lateral and vertical directions. Data obtained are correlated to the temperature used during embossing.

A Twofold Comparison between Dual Cure Resin Modified Cement and Glass Ionomer Cement for Orthodontic Band Cementation.

PubMed

Attar, Hanaa El; Elhiny, Omnia; Salem, Ghada; Abdelrahman, Ahmed; Attia, Mazen

2016-12-15

To test the solubility of dual cure resin modified resin cement in a food simulating solution and the shear bond strength compared to conventional Glass ionomer cement. The materials tested were self-adhesive dual cure resin modified cement and Glass Ionomer (GIC). Twenty Teflon moulds were divided into two groups of tens. The first group was injected and packed with the modified resin cement, the second group was packed with GIC. To test the solubility, each mould was weighed before and after being placed in an analytical reagent for 30 days. The solubility was measured as the difference between the initial and final drying mass. To measure the Shear bond strength, 20 freshly extracted wisdom teeth were equally divided into two groups and embedded in self-cure acrylic resin. Four mm sections of stainless steel bands were cemented to the exposed buccal surfaces of teeth under a constant load of 500 g. Shear bond strength was measured using a computer controlled materials testing machine and the load required to deband the samples was recorded in Newtons. GIC showed significantly higher mean weight loss and an insignificant lower Shear bond strength, compared to dual cure resin Cement. It was found that dual cure resin modified cement was less soluble than glass ionomer cement and of comparable bond strength rendering it more useful clinically for orthodontic band cementation.

Fabrication of flexible grating sensing waveguide based on nano-imprint lithography and micro-replication process

NASA Astrophysics Data System (ADS)

Liu, Yueming; Tian, Weijian; Zhang, Shaojun

2009-05-01

Soft and flexible grating sensing waveguides is urgently demanded in application of micro-bending sensing and surface distortion sensing in medical catheter and smart skin sensing unit etc. Based on Nano-imprint Lithography and micro-replication process, polymer grating waveguides with core size 4μm×20μm and pitch 0.75μm are fabricated successfully in this paper. This novel grating waveguides is soft and flexible enough for related application and with the bio-medical safe feature when used in human body catheter. Fabricated processes are presented including the fabrication of micro mould and UV-replication process, and relative skills are discussed also in this paper.

Challenges to a blow/fill/seal process with airborne microorganisms having different resistances to dry heat.

PubMed

Poisson, Patrick; Sinclair, Colin S; Tallentire, Alan

2006-01-01

Controlled challenges with air dispersed microorganisms having widely different resistances to dry heat, carried out on 624 BFS machine processing growth medium, have shown that higher the heat resistance, the greater the extent of vial contamination. Differences in heat resistance affected also the extent of vial contamination when parison and vial formation were knowingly manipulated through changes made to each of three process variables, provision of ballooning air, mould vacuum delay, and parison extrusion rate. The findings demonstrate that, in this investigational system, exposure of challenge micoorganisms to heat inherent in the process has a controlling influence on vial contamination, an influence that could also control microbiological risk in production environments.

Galaxy mergers moulding the circum-galactic medium - I. The impact of a major merger

NASA Astrophysics Data System (ADS)

Hani, Maan H.; Sparre, Martin; Ellison, Sara L.; Torrey, Paul; Vogelsberger, Mark

2018-03-01

Galaxies are surrounded by sizeable gas reservoirs which host a significant amount of metals: the circum-galactic medium (CGM). The CGM acts as a mediator between the galaxy and the extragalactic medium. However, our understanding of how galaxy mergers, a major evolutionary transformation, impact the CGM remains deficient. We present a theoretical study of the effect of galaxy mergers on the CGM. We use hydrodynamical cosmological zoom-in simulations of a major merger selected from the Illustris project such that the z = 0 descendant has a halo mass and stellar mass comparable to the Milky Way. To study the CGM we then re-simulated this system at a 40 times better mass resolution, and included detailed post-processing ionization modelling. Our work demonstrates the effect the merger has on the characteristic size of the CGM, its metallicity, and the predicted covering fraction of various commonly observed gas-phase species, such as H I, C IV, and O VI. We show that merger-induced outflows can increase the CGM metallicity by 0.2-0.3 dex within 0.5 Gyr post-merger. These effects last up to 6 Gyr post-merger. While the merger increases the total metal covering fractions by factors of 2-3, the covering fractions of commonly observed UV ions decrease due to the hard ionizing radiation from the active galactic nucleus, which we model explicitly. Our study of the single simulated major merger presented in this work demonstrates the significant impact that a galaxy interaction can have on the size, metallicity, and observed column densities of the CGM.

OBSERVATIONS ON THE SUSCEPTIBILITY OF SOME WILD SPECIES OF THE GENUS NICOTINA AND OF SOME VARIETIES OF NICOTIANA TABACUM L. AND N. RUSTICA L. TO BLUE MOULD (PERONOSPORA TABACINA ADAM) -- PULAWY 1962

DTIC Science & Technology

Nicotiana , no manifestations of the mould were observed on the species of N. debneyi and N. exigua. Very weak symptoms appeared in N. paniculata and N... plumbaginifolia . In the group of cigarette-tobacco varieties only the Hicks Resistant and Hicks fixed A2 (varieties of Australian origin, obtained by

[Health-toxicologic aspects of some fungi].

PubMed

Ochmański, W; Barabasz, W

2000-01-01

Recent findings of fungi in food products of such renomed companies as Coca-Cola and Danone resulted in society-wide alert in Poland. Humans have contact with fungi everywhere. Every food product covered with mould or having marks of it should be discarded. We should mention that cutting of or skimming the mould is totally ineffective and dangerous, because of the fact that rest of the product will contain products of fungal metabolism such as mikotoxins, which are, of course, invisible. Modern food producing technologies effected in microorganism-free products, but sporadically we can find dead fungi debris due to improper washing procedures of multi-use bottles, like it was observed in Coca-Cola products. As for mould-covered cottage cheese type products of Danone, most probably reason was improper handling of ready, sealed products during transport and storage. Even minimal physical injuries to air-tight containers resulted in sporae penetration to milk products and finally contamination with mikotoxins.

Interactions between yeasts and bacteria in the smear surface-ripened cheeses.

PubMed

Corsetti, A; Rossi, J; Gobbetti, M

2001-09-19

In the initial phase of ripening, the microflora of bacterial smear surface-ripened cheeses such as Limburger, Taleggio, Brick, Münster and Saint-Paulin and that of surface mould-ripened cheeses such as Camembert and Brie may be similar, but at the end of the ripening, bacteria such as Brevibacterium spp., Arthrobacter spp., Micrococcus spp., Corynebacterium spp. and moulds such as Penicillium camemberti are, respectively, the dominant microorganisms. Yeasts such as Candida spp., Cryptococcus spp., Debaryomyces spp., Geotrichum candidum, Pichia spp., Rhodotorula spp., Saccharomyces spp. and Yarrowia lipolytica are often and variably isolated from the smear surface-ripened cheeses. Although not dominant within the microorganisms of the smear surface-ripened cheeses, yeasts establish significant interactions with moulds and especially bacteria, including surface bacteria and lactic acid bacteria. Some aspects of the interactions between yeasts and bacteria in such type of cheeses are considered in this paper.

Pre-surgical nasoalveolar moulding in patient with unilateral cleft of lip, alveolus and palate: case report.

PubMed

Patel, Dolly; Goyal, Ramesh

2012-01-01

A 2 month-old infant with unilateral cleft lip, alveolus and palate was presented with wide alveolar defect, soft-tissue deformity and a markedly sunken nasal wing at the cleft side. The patient was treated with a moulding plate and additionally with a nasal stent. The device consisted of an acrylic plate with an attached nasal stent that lifted the nasal dome. Under this pre-surgical treatment, the cleft edges moved closer by 9 mm and 6 mm at the alveolar ridge and palate, respectively. The nasal wing was lifted considerably. Pre-surgical nasoalveolar moulding helped to reduce the cleft gap, improve the arch form, approximate lip segments and distinctly improve the morphology of the nose by correcting flattened nasal wings. Copyright © 2011 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

[Moisture and mold on the inner walls of prefabricated building slabs--investigating a strange cause].

PubMed

Kaufhold, T; Fiedler, K; Jung, G; Lindner, M; Gassel, R P

1997-04-01

Reasons for indoor-moisture beyond the normal level can be caused by penetrating dampness, condensation-water, and apartment misuse. A fall in the air temperature below the dew point in connection with moulding inside buildings becomes evident mostly at places like badly insulated outer-walls or room-corners. In a number of houses built between 1980 and 1983 in the so called "Plattenbauweise" (prefabricated slabs), exclusively the inner-walls were covered in mould around cracks in the walls. Examinations showed connections between the apartment and the outer-corridor with a slight exchange of air through the cracks. Warm, wet air escaped from the apartment into the outer-corridor, and cold air entered the apartment from the outer-corridor. This temporary fall below the dewpoint caused by suitable variation of temperature probably resulted in the building materials and wallpapers becoming damp, as well as the growth of mould.

On chirality of slime mould.

PubMed

Dimonte, Alice; Adamatzky, Andrew; Erokhin, Victor; Levin, Michael

2016-02-01

Left-right patterning and lateralised behaviour is an ubiquitous aspect of plants and animals. The mechanisms linking cellular chirality to the large-scale asymmetry of multicellular structures are incompletely understood, and it has been suggested that the chirality of living cells is hardwired in their cytoskeleton. We examined the question of biased asymmetry in a unique organism: the slime mould Physarum polycephalum, which is unicellular yet possesses macroscopic, complex structure and behaviour. In laboratory experiment using a T-shape, we found that Physarum turns right in more than 74% of trials. The results are in agreement with previously published studies on asymmetric movement of muscle cells, neutrophils, liver cells and growing neural filaments, and for the first time reveal the presence of consistently-biased laterality in the fungi kingdom. Exact mechanisms of the slime mould's direction preference remain unknown. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Features of Extrusion Processing of Ultrahigh Molecular Weight Polyethylene. Experiment and Theory

NASA Astrophysics Data System (ADS)

Skul‧skii, O. I.; Slavnov, E. V.

2018-05-01

Experimental studies have been made of the permissible regimes of processing ultrahigh molecular weight polyethylene GUR 2122 with molecular mass of 4.5 million g/moles in a laboratory extruder with an auger diameter 32 mm and a ratio L/D = 20 at temperatures of 155-165oC. On the basis of rotational viscometry, the rheological properties of the melt are described. A mathematical model and a numerical method for calculating the motion of ultrahigh molecular weight polyethylene melt in the auger and in the moulding rigging are proposed. The velocity and stress fields have been determined.

Nano-Composites: Relationships Between Nano-Structure and Mechanical Properties: Phase II

DTIC Science & Technology

2006-01-01

was pre-reacted with the DEGBA resin to give a 40 wt.% CTBN -epoxy adduct: ‘Albipox 1000’ from Hanse Chemie, Geesthacht, Germany. The curing agent was...not lead to a decrease in the modulus of the composite. Nor does it lead to a significant increase in the viscosity of the epoxy resin , which would...preclude the use of low-cost manufacturing routes, such as a vacuum-assisted resin -transfer moulding (VARTM) process. Keywords Epoxy

Rapid tissue engineering of biomimetic human corneal limbal crypts with 3D niche architecture.

PubMed

Levis, Hannah J; Massie, Isobel; Dziasko, Marc A; Kaasi, Andreas; Daniels, Julie T

2013-11-01

Limbal epithelial stem cells are responsible for the maintenance of the human corneal epithelium and these cells reside in a specialised stem cell niche. They are located at the base of limbal crypts, in a physically protected microenvironment in close proximity to a variety of neighbouring niche cells. Design and recreation of elements of various stem cell niches have allowed researchers to simplify aspects of these complex microenvironments for further study in vitro. We have developed a method to rapidly and reproducibly create bioengineered limbal crypts (BLCs) in a collagen construct using a simple one-step method. Liquid is removed from collagen hydrogels using hydrophilic porous absorbers (HPAs) that have custom moulded micro-ridges on the base. The resulting topography on the surface of the thin collagen constructs resembles the dimensions of the stromal crypts of the human limbus. Human limbal epithelial cells seeded onto the surface of the constructs populate these BLCs and form numerous layers with a high proportion of the cells lining the crypts expressing putative stem cell marker, p63α. The HPAs are produced using a moulding process that is flexible and can be adapted depending on the requirements of the end user. Creation of defined topographical features using this process could be applicable to numerous tissue-engineering applications where varied 3-dimensional niche architectures are required. Copyright © 2013 Elsevier Ltd. All rights reserved.

Biopolymer-based thermoplastic mixture for producing solid biodegradable shaped bodies and its photo degradation stability

NASA Astrophysics Data System (ADS)

Sulong, Nurulsaidatulsyida; Rus, Anika Zafiah M.

2013-12-01

In recent years, biopolymers with controllable lifetimes have become increasingly important for many applications in the areas of agriculture, biomedical implants and drug release, forestry, wild life conservation and waste management. Natural oils are considered to be the most important class of renewable sources. They can be obtained from naturally occurring plants, such as sunflower, cotton, linseed and palm oil. In Malaysia, palm oil is an inexpensive and commodity material. Biopolymer produced from palm oil (Bio-VOP) is a naturally occurring biodegradable polymer and readily available from agriculture. For packaging use however, Bio-VOP is not thermoplastic and its granular form is unsuitable for most uses in the plastics industry, mainly due to processing difficulties during extrusion or injection moulding. Thus, research workers have developed several methods to blend Bio-VOP appropriately for industrial uses. In particular, injections moulding processes, graft copolymerisation, and preparation of blends with thermoplastic polymers have been studied to produce solid biodegradable shaped bodies. HDPE was chosen as commercial thermoplastic materials and was added with 10% Bio-VOP for the preparation of solid biodegradable shaped bodies named as HD-VOP. The UV light exposure of HD-VOP at 12 minutes upon gives the highest strength of this material that is 17.6 MPa. The morphological structure of HD-VOP shows dwi structure surface fracture which is brittle and ductile properties.

Microbiological quality of fresh, minimally-processed fruit and vegetables, and sprouts from retail establishments.

PubMed

Abadias, M; Usall, J; Anguera, M; Solsona, C; Viñas, I

2008-03-31

A survey of fresh and minimally-processed fruit and vegetables, and sprouts was conducted in several retail establishments in the Lleida area (Catalonia, Spain) during 2005-2006 to determine whether microbial contamination, and in particular potentially pathogenic bacteria, was present under these commodities. A total of 300 samples--including 21 ready-to-eat fruits, 28 whole fresh vegetables, 15 sprout samples and 237 ready-to-eat salads containing from one to six vegetables--were purchased from 4 supermarkets. They were tested for mesophilic and psychrotrophic aerobic counts, yeasts and moulds, lactic acid bacteria, Enterobacteriaceae, presumptive E. coli and Listeria monocytogenes counts as well as for the presence of Salmonella, E. coli O157:H7, Yersinia enterocolitica and thermotolerant Campylobacter. Results for the fresh-cut vegetables that we analyzed showed that, in general, the highest microorganism counts were associated with grated carrot, arugula and spinach (7.8, 7.5 and 7.4 log cfu g(-1) of aerobic mesophilic microorganisms; 6.1, 5.8 and 5.2 log cfu g(-1) of yeast and moulds; 5.9, 4.0 and 5.1 log cfu g(-1) lactic acid bacteria and 6.2, 5.3 and 6.0 log cfu g(-1) of Enterobacteriaceae). The lowest counts were generally associated with fresh-cut endive and lettuce (6.2 and 6.3 log cfu g(-1) of aerobic mesophilic microorganisms; 4.4 and 4.6 log cfu g(-1) of yeast and moulds; 2.7 and 3.8 log cfu g(-1) lactic acid bacteria and 4.8 and 4.4 log cfu g(-1) of Enterobacteriaceae). Counts of psychrotrophic microorganisms were as high as those of mesophilic microorganisms. Microbiological counts for fresh-cut fruit were very low. Sprouts were highly contaminated with mesophilic (7.9 log cfu g(-1)), psychrotrophic microorganisms (7.3 log cfu g(-1)) and Enterobacteriaceae (7.2 log cfu g(-1)) and showed a high incidence of E. coli (40% of samples). Of the samples analyzed, four (1.3%) were Salmonella positive and two (0.7%) harboured L. monocytogenes. None of the samples was positive for E. coli O157:H7, pathogenic Y. enterocolitica or thermotolerant Campylobacter.

[Moulds isolated from the upper sections of the respiratory and alimentary tracts of healthy veterinary medicine students].

PubMed

Biedunkiewicz, Anna

2011-01-01

The mycological studies in healthy veterinary medicine students have been prompted by the fact that only a few publications are available to date on the occurrence of moulds in people identifying themselves as generally healthy and having direct contact with ill or dead animals. The research material comprised swabs from the oral cavity, nasal cavity and throat of one hundred students (Faculty of Veterinary Medicine, University of Warmia and Mazury in Olsztyn) who declared good health. Initial cultures on the Sabouraud medium were incubated for 72 h at 37 degrees C, then sieved in the Czapek-Dox medium, where they were macroscopically assessed after two weeks. Forcing preparations produced with use of adhesive tape, were stained methylene blue with lactofenol. The studies identified 9 species of fungi from four genera: Aspergillus and Penicillium (mould), Scopulariopsis and Trichophyton (dermatophytes). Penicillium chrysogenum was a dominant feature. Aspergillus fumigatus, Aspergillus niger, A. versicolor and Scopulariopsis brevicaulis were often isolated. Moulds were also accompanied by yeast-like fungi (Candida albicans, Candida tropicalis). Most of the fungi were isolated from the nasal cavity of nicotine abusers and those taking oral hormones. Isolation of potentially pathogenic fungi from people declaring good health may indicate the carrier state or a lowered resistance at the time of material collection. This indicates the need to put a greater emphasis on prevention in subsequent mycological examinations of environmental risk groups.

Identifying risk factors for exposure to culturable allergenic moulds in energy efficient homes by using highly specific monoclonal antibodies

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharpe, Richard A.; Cocq, Kate Le; Nikolaou, Vasilis

The aim of this study was to determine the accuracy of monoclonal antibodies (mAbs) in identifying culturable allergenic fungi present in visible mould growth in energy efficient homes, and to identify risk factors for exposure to these known allergenic fungi. Swabs were taken from fungal contaminated surfaces and culturable yeasts and moulds isolated by using mycological culture. Soluble antigens from cultures were tested by ELISA using mAbs specific to the culturable allergenic fungi Aspergillus and Penicillium spp., Ulocladium, Alternaria, and Epicoccum spp., Cladosporium spp., Fusarium spp., and Trichoderma spp. Diagnostic accuracies of the ELISA tests were determined by sequencing ofmore » the internally transcribed spacer 1 (ITS1)-5.8S-ITS2-encoding regions of recovered fungi following ELISA. There was 100% concordance between the two methods, with ELISAs providing genus-level identity and ITS sequencing providing species-level identities (210 out of 210 tested). Species of Aspergillus/Penicillium, Cladosporium, Ulocladium/Alternaria/Epicoccum, Fusarium and Trichoderma were detected in 82% of the samples. The presence of condensation was associated with an increased risk of surfaces being contaminated by Aspergillus/Penicillium spp. and Cladosporium spp., whereas moisture within the building fabric (water ingress/rising damp) was only associated with increased risk of Aspergillus/Penicillium spp. Property type and energy efficiency levels were found to moderate the risk of indoor surfaces becoming contaminated with Aspergillus/Penicillium and Cladosporium which in turn was modified by the presence of condensation, water ingress and rising damp, consistent with previous literature. - Highlights: • Monoclonal antibodies were used to track culturable allergenic moulds in homes. • Allergenic moulds were recovered from 82% of swabs from contaminated surfaces. • The mAbs were highly specific with 100% agreement to PCR of recovered fungi. • Improvements to energy efficiency lowered risk of exposure to allergenic fungi.« less

Clash of kingdoms or why Drosophila larvae positively respond to fungal competitors.

PubMed

Rohlfs, Marko

2005-01-27

BACKGROUND: Competition with filamentous fungi has been demonstrated to be an important cause of mortality for the vast group of insects that depend on ephemeral resources (e.g. fruit, dung, carrion). Recent data suggest that the well-known aggregation of Drosophila larvae across decaying fruit yields a competitive advantage over mould, by which the larvae achieve a higher survival probability in larger groups compared with smaller ones. Feeding and locomotor behaviour of larger larval groups is assumed to cause disruption of fungal hyphae, leading to suppression of fungal growth, which in turn improves the chances of larval survival to the adult stage. Given the relationship between larval density, mould suppression and larval survival, the present study has tested whether fungal-infected food patches elicit communal foraging behaviour on mould-infected sites by which larvae might hamper mould growth more efficiently. RESULTS: Based on laboratory experiments in which Drosophila larvae were offered the choice between fungal-infected and uninfected food patches, larvae significantly aggregated on patches containing young fungal colonies. Grouping behaviour was also visible when larvae were offered only fungal-infected or only uninfected patches; however, larval aggregation was less strong under these conditions than in a heterogeneous environment (infected and uninfected patches). CONCLUSION: Because filamentous fungi can be deadly competitors for insect larvae on ephemeral resources, social attraction of Drosophila larvae to fungal-infected sites leading to suppression of mould growth may reflect an adaptive behavioural response that increases insect larval fitness and can thus be discussed as an anti-competitor behaviour. These observations support the hypothesis that adverse environmental conditions operate in favour of social behaviour. In a search for the underlying mechanisms of communal behaviour in Drosophila, this study highlights the necessity of investigating the role of inter-kingdom competition as a potential driving force in the evolution of spatial behaviour in insects.

Remelt Ingot Production Technology

NASA Astrophysics Data System (ADS)

Grandfield, J. F.

The technology related to the production of remelt ingots (small ingots, sows and T-Bar) is reviewed. Open mold conveyors, sow casting, wheel and belt casting and VDC and HDC casting are described and compared. Process economics, capacity, product quality and process problems are listed. Trends in casting machine technology such as longer open mold conveyor lines are highlighted. Safety issues related to the operation of these processes are discussed. The advantages and disadvantages of the various machine configurations and options e.g. such as dry filling with the mold out of water and wet filling with the mold in water for open mould conveyors are discussed. The effect of mold design on machine productivity, mold cracking and mold life is also examined.

[Determination of Alternaria mycotoxins in selected raw and processed fruit and vegetable products].

PubMed

Giryn, H; Szteke, B

1995-01-01

The purpose of the study was the assessment of Alternaria-mycotoxins contamination in some raw and processed plant products. The analytical method for detection of alternariol (AOH) and alternariol methyl ether (AME) is described. After extraction and purification of sample crude extracts by column chromatography on silica gel, the qualitative and quantitative analyses were carried out by two-dimensional TLC. There were 110 samples analyzed -44 (included 32 moulded) raw plant samples and 56 processed plant products. Levels of alternaria-mycotoxins found in fruits and tomatoes visibly decayed ranged between 3 to 420 micrograms/kg for AOH and 10 to 100 micrograms/kg for AME. Trace amounts of AOH were detected in 3 samples of processed products.

Micro/nano electro mechanical systems for practical applications

NASA Astrophysics Data System (ADS)

Esashi, Masayoshi

2009-09-01

Silicon MEMS as electrostatically levitated rotational gyroscope, 2D optical scanner and wafer level packaged devices as integrated capacitive pressure sensor and MEMS switch are described. MEMS which use non-silicon materials as diamond, PZT, conductive polymer, CNT (carbon nano tube), LTCC with electrical feedthrough, SiC (silicon carbide) and LiNbO3 for multi-probe data storage, multi-column electron beam lithography system, probe card for wafer-level burn-in test, mould for glass press moulding and SAW wireless passive sensor respectively are also described.

Studies on fabrication of glass fiber reinforced composites using polymer blends

NASA Astrophysics Data System (ADS)

Patel, R. H.; Kachhia, P. H.; Patel, S. N.; Rathod, S. T.; Valand, J. K.

2018-05-01

Glass fiber reinforced PVC/NBR composites have been fabricated via hot compression moulding process. PVC is brittle in nature and thus lower thermal stability. Therefore, to improve the toughness of PVC, NBR was incorporated in certain proportions. As both are polar and thus they are compatible. To improve the strength property further, these blends were used to fabricate glass fiber reinforced composites. SEM micrograph shows good wettability of the blend with glass fibers resulting in proper bonding which increase the strength of the composites.

A new magnesium alloy system: TEXAS

NASA Astrophysics Data System (ADS)

Wiese, Björn; Mendis, Chamini; Blawert, Carsten; Nyberg, Eric; Kainer, Karl Ulrich; Hort, Norbert

A new TEXAS alloy system (Mg-Sn-Nd-Ca-Al-Si) is presented in order to extend the range of applications for magnesium alloys. The alloy has been produced by permanent mould direct chill casting, a process that provides a homogenous distribution of alloying elements throughout the entire casting. This work presents microstructural features and a new Mg-Sn-Ca phase with the morphology of hexagonal platelets. Additionally mechanical properties and the corrosion behaviour of TEXAS alloys are presented in as cast and heat treated conditions.

Influence of UV radiation and nitrosamines on the induction of mycotoxins synthesis by nontoxigenic moulds isolated from feed samples.

PubMed

Aziz, Nagy H; Smyk, B

2002-04-01

The effects of UV radiation and nitrosamines on the induction of mycotoxin biosynthesis by some nontoxigenic moulds isolated from feed samples collected from Egypt and Poland was investigated. Nontoxigenic strains of Aspergillus flavus P-63, A. niger EN-200 and A. ochraceus P-157 synthesized mycotoxins (aflatoxins and ochratoxin, A) after exposure to near UV radiation for 120-210 min. Nitrosamines (DMNA and DENA) at 30 up to 1000 ppm induced the synthesis of aflatoxins by nontoxigenic species of A. flavus ES-255 and P-63 and A. niger EN 200. Near-UV radiation and nitrosamines had no influence on the induction of mycotoxin synthesis by Penicillium and Fusarium isolates. All nontoxigenic strains of Aspergilli which synthesized aflatoxins in the presence of 1000 ppm nitrosamines, also synthesized continuously aflatoxins during the next fifteen generations. Near-UV radiation and nitrosamines had a mutagenic effect on the induction of mycotoxins synthesis by nontoxigenic moulds.

Spergilli on Building Partitions Infested with Moulds in Residential Housing and Public Utility Premises

NASA Astrophysics Data System (ADS)

Piontek, Marlena; Łuszczyńska, Katarzyna; Lechów, Hanna

2017-12-01

Aspergilli constitute a serious risk to the health of the inhabitants of infested rooms. Mycological analysis conducted in buildings infected with moulds in the area of the Lubuskie province (Poland) demonstrated the presence of 9 species of Aspergillus moulds: A. carbonarius A. clavatus, A. flavus, A. fumigatus, A. niger, A. ochraceus, A. terreus, A ustus and A. versicolor. The highest frequency (4 - frequently) was observed in the case of A. versicolor, while frequency 3 (fairly frequently) was characteristic of such species as A. flavus and A. niger. A. ustus was encountered with frequency 2 (individually), while frequency 1 (sporadically) referred to four species: A. carbonarius, A. clavatus, A. fumigatus and A. terreus. Because Aspergillus versicolor occurs with the highest frequency in buildings, and as a consequence of this, synthesizes toxic and carcinogenic sterigmatocystin (ST), it constitutes the greatest risk to the inhabitants of the infested premises. All species of Aspergillus present on building partitions are able to synthesise mycotoxins, are pathogens and may cause allergies.

Study of design and technology factors influencing gas turbine blade cooling

NASA Astrophysics Data System (ADS)

Shevchenko, I. V.; Garanin, I. V.; Rogalev, A. N.; Kindra, V. O.; Khudyakova, V. P.

2017-11-01

The knowledge of aerodynamic and thermal parameters of turbulators used in order to design an efficient blade cooling system. However, all experimental tests of the hydraulic and thermal characteristics of the turbulators were conducted on the rectangular shape channels with a strongly defined air flow direction. The actual blades have geometry of the channels that essentially differs from the rectangular shape. Specifically, the air flow in the back cavity of a blade with one and half-pass cooling channel changes its direction throughout the feather height. In most cases the ribs and pins are made with a tilt to the channel walls, which is determined by the moving element design of a mould for the ceramic rod element fabrication. All of the factors described above may result in the blade thermohydraulic model being developed failing to fully simulate the air flow and the heat exchange processes in some sections of the cooling path. Hence, the design temperature field will differ from the temperature field of an actual blade. This article studied the numerical data of design and technology factors influencing heat transfer in the cooling channels. The results obtained showed their substantial impact on the blade cooling efficiency.

Characterisation and modelling of defect formation in direct-chill cast AZ80 alloy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mackie, D.; Robson, J.D.; Withers, P.J.

2015-06-15

Wrought magnesium alloys for demanding structural applications require high quality defect free cast feedstock. The aim of this study was to first identify and characterise typical defects in direct chill cast magnesium–aluminium–zinc (AZ) alloy billet and then use modelling to understand the origins of these defects so they can be prevented. Defects were first located using ultrasonic inspection and were then characterised using X-ray computed tomography (XCT) and serial sectioning, establishing the presence of oxide films and intermetallic particles Al{sub 8}Mn{sub 5} in all defects. A model was developed to predict the flow patterns and growth kinetics of the intermetallicmore » phases during casting, which influence the formation of defects. Simulation of the growth of the intermetallic particles demonstrated that precipitation from the liquid occurs in the mould. The combination of the entrained oxide films and intermetallic particles recirculates in the liquid metal and continues to grow, until large enough to settle, which is predicted to occur at the centre of the mould where the flow is the slowest. Based on these predictions, strategies to reduce the susceptibility to defect formation are suggested. - Highlights: • Casting defects in magnesium direct chill casting have been imaged and characterised in 3-dimensions. • The occurrences of co-located clusters of particles and oxide films have been characterised and explained. • A coupled model has been developed to help interpret the observed trend for defects located towards the centre of billets.« less

A Twofold Comparison between Dual Cure Resin Modified Cement and Glass Ionomer Cement for Orthodontic Band Cementation

PubMed Central

Attar, Hanaa El; Elhiny, Omnia; Salem, Ghada; Abdelrahman, Ahmed; Attia, Mazen

2016-01-01

AIM: To test the solubility of dual cure resin modified resin cement in a food simulating solution and the shear bond strength compared to conventional Glass ionomer cement. MATERIALS AND METHOD: The materials tested were self-adhesive dual cure resin modified cement and Glass Ionomer (GIC). Twenty Teflon moulds were divided into two groups of tens. The first group was injected and packed with the modified resin cement, the second group was packed with GIC. To test the solubility, each mould was weighed before and after being placed in an analytical reagent for 30 days. The solubility was measured as the difference between the initial and final drying mass. To measure the Shear bond strength, 20 freshly extracted wisdom teeth were equally divided into two groups and embedded in self-cure acrylic resin. Four mm sections of stainless steel bands were cemented to the exposed buccal surfaces of teeth under a constant load of 500 g. Shear bond strength was measured using a computer controlled materials testing machine and the load required to deband the samples was recorded in Newtons. RESULTS: GIC showed significantly higher mean weight loss and an insignificant lower Shear bond strength, compared to dual cure resin Cement. CONCLUSION: It was found that dual cure resin modified cement was less soluble than glass ionomer cement and of comparable bond strength rendering it more useful clinically for orthodontic band cementation. PMID:28028417

Differential Control Efficacies of Vitamin Treatments against Bacterial Wilt and Grey Mould Diseases in Tomato Plants

PubMed Central

Hong, Jeum Kyu; Kim, Hyeon Ji; Jung, Heesoo; Yang, Hye Ji; Kim, Do Hoon; Sung, Chang Hyun; Park, Chang-Jin; Chang, Seog Won

2016-01-01

Bacterial wilt and grey mould in tomato plants are economically destructive bacterial and fungal diseases caused by Ralstonia solanacearum and Botrytis cinerea, respectively. Various approaches including chemical and biological controls have been attempted to arrest the tomato diseases so far. In this study, in vitro growths of bacterial R. solanacearum and fungal B. cinerea were evaluated using four different vitamins including thiamine (vitamin B1), niacin (vitamin B3), pyridoxine (vitamin B6), and menadione (vitamin K3). In planta efficacies of the four vitamin treatments on tomato protection against both diseases were also demonstrated. All four vitamins showed different in vitro antibacterial activities against R. solanacearum in dose-dependent manners. However, treatment with 2 mM thiamine was only effective in reducing bacterial wilt of detached tomato leaves without phytotoxicity under lower disease pressure (106 colony-forming unit [cfu]/ml). Treatment with the vitamins also differentially reduced in vitro conidial germination and mycelial growth of B. cinerea. The four vitamins slightly reduced the conidial germination, and thiamine, pyridoxine and menadione inhibited the mycelial growth of B. cinerea. Menadione began to drastically suppress the conidial germination and mycelial growth by 5 and 0.5 mM, respectively. Grey mould symptoms on the inoculated tomato leaves were significantly reduced by pyridoxine and menadione pretreatments one day prior to the fungal challenge inoculation. These findings suggest that disease-specific vitamin treatment will be integrated for eco-friendly management of tomato bacterial wilt and grey mould. PMID:27721697

Differential Control Efficacies of Vitamin Treatments against Bacterial Wilt and Grey Mould Diseases in Tomato Plants.

PubMed

Hong, Jeum Kyu; Kim, Hyeon Ji; Jung, Heesoo; Yang, Hye Ji; Kim, Do Hoon; Sung, Chang Hyun; Park, Chang-Jin; Chang, Seog Won

2016-10-01

Bacterial wilt and grey mould in tomato plants are economically destructive bacterial and fungal diseases caused by Ralstonia solanacearum and Botrytis cinerea , respectively. Various approaches including chemical and biological controls have been attempted to arrest the tomato diseases so far. In this study, in vitro growths of bacterial R. solanacearum and fungal B. cinerea were evaluated using four different vitamins including thiamine (vitamin B1), niacin (vitamin B3), pyridoxine (vitamin B6), and menadione (vitamin K3). In planta efficacies of the four vitamin treatments on tomato protection against both diseases were also demonstrated. All four vitamins showed different in vitro antibacterial activities against R. solanacearum in dose-dependent manners. However, treatment with 2 mM thiamine was only effective in reducing bacterial wilt of detached tomato leaves without phytotoxicity under lower disease pressure (10 6 colony-forming unit [cfu]/ml). Treatment with the vitamins also differentially reduced in vitro conidial germination and mycelial growth of B. cinerea . The four vitamins slightly reduced the conidial germination, and thiamine, pyridoxine and menadione inhibited the mycelial growth of B. cinerea . Menadione began to drastically suppress the conidial germination and mycelial growth by 5 and 0.5 mM, respectively. Grey mould symptoms on the inoculated tomato leaves were significantly reduced by pyridoxine and menadione pretreatments one day prior to the fungal challenge inoculation. These findings suggest that disease-specific vitamin treatment will be integrated for eco-friendly management of tomato bacterial wilt and grey mould.

Warpage minimization on wheel caster by optimizing process parameters using response surface methodology (RSM)

NASA Astrophysics Data System (ADS)

Safuan, N. S.; Fathullah, M.; Shayfull, Z.; Nasir, S. M.; Hazwan, M. H. M.

2017-09-01

In injection moulding process, it is important to keep the productivity increase constantly with least of waste produced such as warpage defect. Thus, this study is concerning on minimizing warpage defect on wheel caster part. Apart from eliminating product wastes, this project also giving out best optimization techniques using response surface methodology. This research studied on five parameters A-packing pressure, B-packing time, C-mold temperature, D-melting temperature and E-cooling time. The optimization showed that packing pressure is the most significant parameter. Warpage have been improved 42.64% from 0.6524 mm to 0.3742mm.

Characterization of plastic blends made from mixed plastics waste of different sources.

PubMed

Turku, Irina; Kärki, Timo; Rinne, Kimmo; Puurtinen, Ari

2017-02-01

This paper studies the recyclability of construction and household plastic waste collected from local landfills. Samples were processed from mixed plastic waste by injection moulding. In addition, blends of pure plastics, polypropylene and polyethylene were processed as a reference set. Reference samples with known plastic ratio were used as the calibration set for quantitative analysis of plastic fractions in recycled blends. The samples were tested for the tensile properties; scanning electron microscope-energy-dispersive X-ray spectroscopy was used for elemental analysis of the blend surfaces and Fourier transform infrared (FTIR) analysis was used for the quantification of plastics contents.

Design and Development of Tilting Rotary Furnace

NASA Astrophysics Data System (ADS)

Sai Varun, V.; Tejesh, P.; Prashanth, B. N.

2018-02-01

Casting is the best and effective technique used for manufacturing products. The important accessory for casting is furnace. Furnace is used to melt the metal. A perfect furnace is one that reduces the wastage of material, reduces the cost of manufacturing and there by reduces the cost of production. Of all the present day furnaces there may be wastage of material, and the chances of increasing the time of manufacturing as the is continuous need of tilting of the furnace for every mould and then changing the moulds. Considering these aspects, a simple and least expensive tilting rotary furnace is designed and developed. The Tilting and Rotary Furnace consists of mainly melting chamber and the base. The metal enters the melting chamber through the input door that is provided on the top of the melting chamber. Inside the melting chamber there is a graphite furnace. The metal is melted in the graphite crucible. An insulation of ceramic fibre cloth is provided inside the furnace. The metal is melted using Propane gas. The propane gas is easily available and economic. The gas is burned using a pilot burner. The pilot burner is more efficient that other burners. The pilot burner is lit with a push button igniter. The pilot burner is located at the bottom of the combustion chamber. This enables the uniform heating of the metal inside the crucible. The temperature inside the melting chamber is noted using a temperature sensor. The gas input is cut-off if the temperature is exceeding a specific temperature. After the melting of the metal is done the furnace is tilted and after the mould is filled it is rotated. The external gears are used to controlling the tilting. The results of studies carried out for the design & development of low cost, simple furnace that can be mounted anywhere on the shop floor and this can be very much useful for the education purposes and small scale manufacturing. The furnace can be rotated in 360 degrees and can help in reducing the time taken in manufacturing. The furnace is provided with a rotation motion to the base which helps in providing a uniform distribution of molten metal to various moulds and can be used to fill a number of moulds with minimal wastage of the molten material. Due to the tilting action provided to the combustion chamber, the flow of metal can be controlled easily during pouring of molten metal into the moulds.

Annual Review of Progress in Applied Computational Electromagnetics (5th), Held in Monterey, California on March 20-24 1989

DTIC Science & Technology

1989-01-01

circuit of the field equations of Maxwell ", Proc IRE, vol 32, Kay 1944, pp 360-367. 3. S. Akhtarzad P.B. Johns ,"Solution of Maxwell’s equations in three...ELFCTROMAGNETICS APPLIED TO INTEGRATED CIRCUIT MICROLITHOGRAPHY AND METROLOGY John C . Mould Jr. & Gregory L Wojc* Welinger Associates, 4410 El Camino Real, Los...1AICROLITHOGRAPHY AND METROLOGY John C . Mould Jr. & Gregory L Wo c * Weldlinger Associates, 4410 El Camino Real. Los Allos, Ca. 94022 1. Pholoreslat

Apatitic connecting rings in moulds of Baculites sp. from the middle part of the Smoky Hill Member, Niobrara Chalk (Santonian), of western Kansas

USGS Publications Warehouse

Hasenmueller, W.A.; Hattin, D.E.

1985-01-01

Moulds of Baculites sp. are common in the Smoky Hill Member but only five known specimens contain connecting rings that have been preserved because of mineralisation by carbonate apatite. Analysis of four of these specimens suggests that the connecting rings were originally composed of organic material and were mineralised during early diagenesis. Thin sections and scanning electron microscopy demonstrate that the connecting rings had a two-layered structure consisting of a thick siphuncular wall and a thin pellicle. ?? 1985.

Basis of predictive mycology.

PubMed

Dantigny, Philippe; Guilmart, Audrey; Bensoussan, Maurice

2005-04-15

For over 20 years, predictive microbiology focused on food-pathogenic bacteria. Few studies concerned modelling fungal development. On one hand, most of food mycologists are not familiar with modelling techniques; on the other hand, people involved in modelling are developing tools dedicated to bacteria. Therefore, there is a tendency to extend the use of models that were developed for bacteria to moulds. However, some mould specificities should be taken into account. The use of specific models for predicting germination and growth of fungi was advocated previously []. This paper provides a short review of fungal modelling studies.

Fabrication of anti-adhesion surfaces on aluminium substrates of rubber plastic moulds using electrolysis plasma treatment

NASA Astrophysics Data System (ADS)

Meng, Jianbing; Dong, Xiaojuan; Wei, Xiuting; Yin, Zhanmin

2015-04-01

An anti-adhesion surface with a water contact angle of 167° was fabricated on aluminium samples of rubber plastic moulds by electrolysis plasma treatment using mixed electrolytes of C6H5O7(NH4)3 and Na2SO4, followed by fluorination. To optimise the fabrication conditions, several important processing parameters such as the discharge voltage, discharge time, concentrations of supporting electrolyte and stearic acid ethanol solution were examined systematically. Using scanning electron microscopy (SEM) to analyse surfaces morphology, micrometer scale pits, and protrusions were found on the surface, with numerous nanometer mastoids contained in the protrusions. These binary micro/nano-scale structures, which are similar to the micro-structures of soil-burrowing animals, play a critical role in achieving low adhesion properties. Otherwise, the anti-adhesion behaviours of the resulting samples were analysed by the atomic force microscope (AFM), Fourier-transform infrared spectrophotometer (FTIR), electrons probe micro-analyzer (EPMA), optical contact angle meter, digital Vickers microhardness (Hv) tester, and electronic universal testing. The results show that the electrolysis plasma treatment does not require complex processing parameters, using a simple device, and is an environment-friendly and effective method. Under the optimised conditions, the contact angle (CA) for the modified anti-adhesion surface is up to 167°, the sliding angle (SA) is less than 2°, roughness of the sample surface is only 0.409μm. Moreover, the adhesion force and Hv are 0. 9KN and 385, respectively.

The influence of the mould cooling temperature on the surface appearance and the internal quality of ESR ingots

NASA Astrophysics Data System (ADS)

Kubin, M.; Ofner, B.; Holzgruber, H.; Schneider, R.; Enzenhofer, D.; Filzwieser, A.; Konetschnik, S.

2016-07-01

One of the main benefits of the ESR process is to obtain an ingot surface which is smooth and allows a subsequent forging operation without any surface dressing. The main influencing factor on surface quality is the precise controlling of the process such as melt rate and electrode immersion depth. However, the relatively strong cooling effect of water as a cooling medium can result in the solidification of the meniscus of the liquid steel on the boundary liquid steel and slag which is most likely the origin of surface defects. The usage of different cooling media like ionic liquids, a salt solution which can be heated up to 250°C operating temperature might diminish the meniscus solidification phenomenon. This paper shows the first results of the usage of an ionic liquid as a mould cooling medium. In doing so, 210mm diameter ESR ingots were produced with the laboratory scale ESR furnace at the university of applied science using an ionic liquid cooling device developed by the company METTOP. For each trial melt different inlet and outlet temperatures of the ionic liquid were chosen and the impact on the surface appearance and internal quality were analyzed. Furthermore the influence on the energy balance is also briefly highlighted. Ultimately, an effect of the usage of ionic liquids as a cooling medium could be determined and these results will be described in detail within the scope of this paper.

Microbiota of high-pressure-processed Serrano ham investigated by culture-dependent and culture-independent methods.

PubMed

Martínez-Onandi, N; Castioni, A; San Martín, E; Rivas-Cañedo, A; Nuñez, M; Torriani, S; Picon, A

2017-01-16

The microbiota of Serrano dry-cured ham of different chemical composition, subjected or not to high-pressure processing (HPP), was investigated using culture-dependent and culture-independent methods. Microbial counts were submitted to analysis of variance with physicochemical parameters (a w , NaCl concentration, salt-in-lean ratio and intramuscular fat content) or HPP as main effects. In untreated hams, physicochemical parameters significantly affected counts of aerobic mesophiles, psychrotrophs, and moulds and yeasts. NaCl concentration and fat content influenced the levels of four and three of the five studied microbial groups, respectively, whereas no influence of a w was stated. The HPP treatment had a significant effect on counts of all investigated microbial groups. Culture-independent methods showed the presence of bacteria such as Staphylococcus equorum, Staphylococcus succinus, Bacillus subtilis and Cellulosimicrobium sp., moulds like Penicillium commune, Aspergillus fumigatus, Sclerotinia sclerotiorum, Eurotium athecium and Moniliella mellis, and yeasts like Debaryomyces hansenii and Candida glucosophila. Absence of B. subtilis bands and weaker bands of E. athecium were recorded for HPP-treated hams. The higher microbial levels found in lean ham might result in a quicker deterioration. HPP treatment confirmed its suitability as a procedure to control spoilage microorganisms. DGGE did not seem to be sensitive enough to highlight changes caused by HPP treatment in the microbiota of ham, but contributed to the detection of microbial species not previously found in ham. Copyright © 2016 Elsevier B.V. All rights reserved.

"Artificial micro organs"--a microfluidic device for dielectrophoretic assembly of liver sinusoids.

PubMed

Schütte, Julia; Hagmeyer, Britta; Holzner, Felix; Kubon, Massimo; Werner, Simon; Freudigmann, Christian; Benz, Karin; Böttger, Jan; Gebhardt, Rolf; Becker, Holger; Stelzle, Martin

2011-06-01

In order to study possible toxic side effects of potential drug compounds in vitro a reliable test system is needed. Predicting liver toxicity presents a major challenge of particular importance as liver cells grown in a cell culture suffer from a rapid loss of their liver specific functions. Therefore we are developing a new microfluidic test system for liver toxicity. This test system is based on an organ-like liver 3D co-culture of hepatocytes and endothelial cells. We devised a microfluidic chip featuring cell culture chambers with integrated electrodes for the assembly of liver sinusoids by dielectrophoresis. Fluid channels enable an organ-like perfusion with culture media and test compounds. Different chamber designs were studied and optimized with regard to dielectrophoretic force distribution, hydrodynamic flow profile, and cell trapping rate using numeric simulations. Based on simulation results a microchip was injection-moulded from COP. This chip allowed the assembly of viable hepatocytes and endothelial cells in a sinusoid-like fashion.

Colour Based Image Processing Method for Recognizing Ribbed Smoked Sheet Grade

NASA Astrophysics Data System (ADS)

Fibriani, Ike; Sumardi; Bayu Satriya, Alfredo; Budi Utomo, Satryo

2017-03-01

This research proposes a colour based image processing technique to recognize the Ribbed Smoked Sheet (RSS) grade so that the RSS sorting process can be faster and more accurate than the traditional one. The RSS sheet image captured by the camera is transformed into grayscale image to simplify the recognition of rust and mould on the RSS sheet. Then the grayscale image is transformed into binary image using threshold value which is obtained from the RSS 1 reference colour. The grade recognition is determined by counting the white pixel percentage. The result shows that the system has 88% of accuracy. Most faults exist on RSS 2 recognition. This is due to the illumination distribution which is not equal over the RSS image.

Interaction of media on production and biocontrol efficacy of Pseudomonas fluorescens and Bacillus subtilis against grey mould of apple.

PubMed

Peighamy-Ashnaei, S; Sharifi-Tehrani, A; Ahmadzadeh, M; Behboudi, K

2008-01-01

The medium has a profound effect on biocontrol agents, including ability to grow and effectiveness in disease control. In this study, growth and antagonistic efficacy of strains P-5 and P-35 (P. fluorescens), B-3 and B-16 (B. subtilis) were evaluated in combinations of two carbon (sucrose and molasses) and two nitrogen (urea and yeast extract) sources to optimize control of Botrytis cinerea on apple. All of the strains were grown in different liquid media (pH = 6.9) including: sucrose + yeast extract, molasses of sugar beet + yeast extract in 2:1 and 1:1 w/w ratios, molasses of sugar beet + urea, molasses, malt extract and nutrient broth. Apples (Golden Delicious) were inoculated by a 25-microl suspension of 10(6) spores of B. cinerea per ml, wounding each fruit (in two sites separately). Then a 25-microl suspension of each strain, containing 2 x 10(8) cfu ml(-1) grown in each of the above culture media, was applied to each wound. Results indicated that Molasses + Yeast extract (1:1 w/w) medium supported rapid growth in all of the strains. The final growth of B. subtilis B-16 in Molasses + Yeast extract (1:1 w/w) medium was 5 x 10(9) cfu ml(-1). After ten days, all of the strains significantly inhibited pathogenicity of B. cinerea on apples. The biocontrol efficacy of B. subtilis B-3 in Molasses + Yeast extract (1:1 w/w) medium reduced the severity of grey mould from 100% (inoculated control) to less than 26.9%. After 20 days, Strain B-3 showed a considerable biocontrol efficacy in Molasses medium and reduced the severity of grey mould from 100% (inoculated control) to less than 38.2%. The results obtained in this study could be used to provide a reliable basis for the increase of population of biocontrol agents in fermentation process.

Investigations of the surface activation of thermoplastic polymers by atmospheric pressure plasma treatment with a stationary plasma jet

NASA Astrophysics Data System (ADS)

Moritzer, Elmar; Nordmeyer, Timo; Leister, Christian; Schmidt, Martin Andreas; Grishin, Artur; Knospe, Alexander

2016-03-01

The production of high-quality thermoplastic parts often requires an additional process step after the injection molding stage. This may be a coating, bonding process or a 2K-injection moulding process. A commonly used process to improve the bond strength is atmospheric pressure plasma treatment. A variety of applications are realized with the aid of CNC systems. Although they ensure excellent reproducibility, they make it difficult to implement inline applications. This paper therefore examines the possibility of surface treatment using a stationary plasma jet. However, before it is possible to integrate this technology into a production process, preliminary trials need to be carried out to establish which factors influence the process. Experimental tests were performed using a special test set-up, enabling geometric, plasma-specific parameters to be identified. These results can help with the practical integration of this technology into existing production processes.

Asthma, allergy and eczema among adults in multifamily houses in Stockholm (3-HE study)--associations with building characteristics, home environment and energy use for heating.

PubMed

Norbäck, Dan; Lampa, Erik; Engvall, Karin

2014-01-01

Risk factors for asthma, allergy and eczema were studied in a stratified random sample of adults in Stockholm. In 2005, 472 multifamily buildings (10,506 dwellings) were invited (one subject/dwelling) and 7,554 participated (73%). Associations were analyzed by multiple logistic regression, adjusting for gender, age, smoking, country of birth, income and years in the dwelling. In total, 11% had doctor's diagnosed asthma, 22% doctor's diagnosed allergy, 23% pollen allergy and 23% eczema. Doctor's diagnosed asthma was more common in dwellings with humid air (OR = 1.74) and mould odour (OR = 1.79). Doctor's diagnosed allergy was more common in buildings with supply exhaust air ventilation as compared to exhaust air only (OR = 1.45) and was associated with redecoration (OR = 1.48) and mould odour (OR = 2.35). Pollen allergy was less common in buildings using more energy for heating (OR = 0.75) and was associated with humid air (OR = 1.76) and mould odour (OR = 2.36). Eczema was more common in larger buildings (OR 1.07) and less common in buildings using more energy for heating (OR = 0.85) and was associated with water damage (OR = 1.47), humid air (OR = 1.73) and mould odour (OR = 2.01). Doctor's diagnosed allergy was less common in buildings with management accessibility both in the neighbourhood and in larger administrative divisions, as compared to management in the neighbourhood only (OR = 0.49; 95% CI 0.29-0.82). Pollen allergy was less common if the building maintenance was outsourced (OR = 0.67; 95% CI 0.51-0.88). Eczema was more common when management accessibility was only at the division level (OR = 1.49; 95% CI 1.06-2.11). In conclusions, asthma, allergy or eczema were more common in buildings using less energy for heating, in larger buildings and in dwellings with redecorations, mould odour, dampness and humid air. There is a need to reduce indoor chemical emissions and to control dampness. Energy saving may have consequences for allergy and eczema. More epidemiological studies are needed on building management organization.

Interaction of Wild Strains of Aspergilla with Aspergillus parasiticus ATCC15517 and Aflatoxin Production †

PubMed Central

Martins, H. Marina; Almeida, Inês; Marques, Marta; Bernardo, Fernando

2008-01-01

Aflatoxins are secondary metabolites produced by some competent mould strains of Aspergillus flavus, A. parasiticus and A. nomius. These compounds have been extensively studied with regards to their toxicity for animals and humans; they are able to induce liver cancer and may cause a wide range of adverse effects in living organisms. Aflatoxins are found as natural contaminants of food and feed; the main line of the strategy to control them is based on the prevention of the mould growth in raw vegetable or during its storage and monitoring of each crop batch. Mould growth is conditioned by many ecological factors, including biotic ones. Hazard characterization models for aflatoxins in crops must take into consideration biotic interactions between moulds and their potential effects on growth development. The aim of this work is to study the effect of the biotic interaction of 14 different wild strains of Aspergilla (different species), with a competent strain (Aspergillus parasiticus ATCC 15517) using an in vitro production model. The laboratory model used was a natural matrix (humidified cracked corn), on which each wild strain challenged the aflatoxin production of a producer strain. Cultures were incubated at 28°C for 12 days and sampled at the 8th and 12th. Aflatoxin detection and quantification was performed by HPLC using a procedure with a MRPL = 1 μg/kg. Results of those interactive cultures revealed both synergic and antagonistic effects on aflatoxin biosynthesis. Productivity increases were particularly evident on the 8th day of incubation with wild strains of A. flavipes (+ 70.4 %), A. versicolor (+ 54.9 %) and A. flavus 3 (+ 62.6 %). Antagonistic effects were found with A. niger (− 69.5%), A. fumigatus (− 47.6 %) and A. terreus (− 47.6 %) on the 12th day. The increased effects were more evident on the 8th of incubation and the decreases were more patent on the 12th day. Results show that the development of Aspergilla strains concomitantly with competent aflatoxin producing moulds has a significant influence on the natural biosynthesis pattern. PMID:19325757

The ultrahigh precision form measurement of small, steep-sided aspheric moulds, incorporating novel hardware and software developments; Technical Digest

NASA Astrophysics Data System (ADS)

Mills, M. W.; Hutchinson, Matthew J.

2005-05-01

A variety of consumer applications, eg cellphone camera lenses, optical storage devices, digital cameras, etc, are driving the demand for small, high aspheric departure rotationally-symmetric moulded optics, manufactured both in polymer and glass materials. The mould tools for such components are manufactured by ultra-high precision techniques such as single point diamond turning and ultra-precision grinding, and must be accurate to <1/10μm levels for form, and exhibit nanometric surface finish quality. The aspheric forms of such components' optical surfaces exhibit high departure from best-fit sphere towards their outer edge, which renders this outer region especially critical for optical performance. The high slope of these components at the clear aperture has caused some restrictions on the use of profilometry in the measurement of form across their full diameter. Taylor Hobson designs and manufactures a range of ultra-precision profilometers for use in such industries as aspheric optics fabrication. In order to address the issues described, a new measurement system, Taylor Hobson Form Talysurf PGI 1250, has been developed, which contains new Aspheric Data Fusion Software, as well as Asphero-Diffractive Analysis Software, allowing the entire diametric profile to be analysed to the desired level of accuracy. This development removes the previous limitation of maximum slope for this type of measurement, thus enabling better quality control of high slope, high aspheric departure optics. Measurement data from the Form Talysurf PGI 1250 can be fed back directly to the machine tool, in order to optimize the form of the optical mould.

The ultrahigh precision form measurement of small, steep-sided aspheric moulds, incorporating novel hardware and software developments; Technical Digest

NASA Astrophysics Data System (ADS)

Mills, M. W.; Hutchinson, Matthew J.

2005-05-01

A variety of consumer applications, eg cellphone camera lenses, optical storage devices, digital cameras, etc, are driving the demand for small, high aspheric departure rotationally-symmetric moulded optics, manufactured both in polymer and glass materials. The mould tools for such components are manufactured by ultra-high precision techniques such as single point diamond turning and ultra-precision grinding, and must be accurate to <1/10μm levels for form, and exhibit nanometric surface finish quality. The aspheric forms of such components" optical surfaces exhibit high departure from best-fit sphere towards their outer edge, which renders this outer region especially critical for optical performance. The high slope of these components at the clear aperture has caused some restrictions on the use of profilometry in the measurement of form across their full diameter. Taylor Hobson designs and manufactures a range of ultra-precision profilometers for use in such industries as aspheric optics fabrication. In order to address the issues described, a new measurement system, Taylor Hobson Form Talysurf PGI 1250, has been developed, which contains new Aspheric Data Fusion Software, as well as Asphero-Diffractive Analysis Software, allowing the entire diametric profile to be analysed to the desired level of accuracy. This development removes the previous limitation of maximum slope for this type of measurement, thus enabling better quality control of high slope, high aspheric departure optics. Measurement data from the Form Talysurf PGI 1250 can be fed back directly to the machine tool, in order to optimize the form of the optical mould.

Breast volume assessment: comparing five different techniques.

PubMed

Bulstrode, N; Bellamy, E; Shrotria, S

2001-04-01

Breast volume assessment is not routinely performed pre-operatively because as yet there is no accepted technique. There have been a variety of methods published, but this is the first study to compare these techniques. We compared volume measurements obtained from mammograms (previously compared to mastectomy specimens) with estimates of volume obtained from four other techniques: thermoplastic moulding, magnetic resonance imaging, Archimedes principle and anatomical measurements. We also assessed the acceptability of each method to the patient. Measurements were performed on 10 women, which produced results for 20 breasts. We were able to calculate regression lines between volume measurements obtained from mammography to the other four methods: (1) magnetic resonance imaging (MRI), 379+(0.75 MRI) [r=0.48], (2) Thermoplastic moulding, 132+(1.46 Thermoplastic moulding) [r=0.82], (3) Anatomical measurements, 168+(1.55 Anatomical measurements) [r=0.83]. (4) Archimedes principle, 359+(0.6 Archimedes principle) [r=0.61] all units in cc. The regression curves for the different techniques are variable and it is difficult to reliably compare results. A standard method of volume measurement should be used when comparing volumes before and after intervention or between individual patients, and it is unreliable to compare volume measurements using different methods. Calculating the breast volume from mammography has previously been compared to mastectomy samples and shown to be reasonably accurate. However we feel thermoplastic moulding shows promise and should be further investigated as it gives not only a volume assessment but a three-dimensional impression of the breast shape, which may be valuable in assessing cosmesis following breast-conserving-surgery.

A feasibility study for using ABS plastic and a low-cost 3D printer for patient-specific brachytherapy mould design.

PubMed

Harris, Benjamin D; Nilsson, Sanna; Poole, Christopher M

2015-09-01

This feasibility study aims to determine if a low-cost 3D printer (BitsFromBytes 3D Touch) with ABS plastic can print custom mould structures and catheter channels defined in a brachytherapy treatment planning system (Nucletron Oncentra) for patient-specific treatment. Printer accuracy was evaluated through physical measurement, and print quality was investigated by adjusting print parameters (print speed, layer thickness, percentage infill). Catheter positioning and reproducibility were measured over repeated insertions. ABS plastic water equivalency was investigated by comparing Ir-192 HDR source dose distributions, measured with radiochromic film, in ABS plastic and in water. Structures and catheter channels were printed accurately to within 0.5 mm laterally and 1 mm in the vertical print direction. Adjusting print parameters could reduce print time, albeit with reduced print quality. 3.5 mm channel diameters allowed for easy catheter insertion. Catheter positioning was reproducible to within 0.5 mm but, because of catheter flex within the channel, was on average 1 mm offset from defined TPS positions. This offset could be accounted for by repeating the treatment planning CT scan with the printed mould positioned on the patient. Dose attenuation in ABS plastic and in water was equivalent to within the measurement limitations. While clinical uses for this particular low-cost printer and ABS plastic are limited by print size restrictions and non-certification for biocompatibility, it has been demonstrated that a low-cost 3D printer set-up can accurately create custom moulds and catheter channels potentially acceptable for clinical use.

Mycological analysis of cereal samples and screening of Fusarium strains' ability to form deoxynivalenole (DON) and zearalenone (ZEA) mycotoxins--a pilot study.

PubMed

Kłyszejko, Adriana; Kubus, Zaneta; Zakowska, Zofia

2005-01-01

Filamentous fungi are cosmopolitan microorganisms found in almost all environments. It should be pointed out that occurance of moulds on food or feed may cause health disorders in humans and animals. Mycoflora appears as a source of toxic methabolites, mycotoxins, which hepatotoxic, genotoxic, nefrotoxic and carcinogenic abilities were already proven in several studies. Hense mycological analysis of cereal grains raises as an important manner in evaluation of food and feed health features. Among the most frequent cereal contaminants Alternaria, Aspergillus, Fusarium and Penicillium strains are mentioned. Due to their ability to grow on cereals during both its field growth and storage, Fusarium moulds occure to be an important contamination factors in food and feed industry. In this study Fusarium strains isolates from wheat and maize were examined in order to recognize their abilities to produce two toxins: zearalenon (ZEA) and deoxynivalenole (DON). Mycological analysis shown differentiation within fungal microflora occuring in samples of different storage conditions, where Fusarium strains represented aproximately 20-70% of all mould species present. In purpose of Fusarium strains species evaluation, isolates were mycologically analysed. In the second step of the project, toxicological screening of isolates was performed using Thin Liquid Chromatography (TLC) evaluating toxigenic potential of single strains' production of ZEA and DON. This data gives the possibility of pointing the most toxigenic strains and also shows differentiations in their occurance in cereals. This paper presents introductory research data, which can be useful in recognition of cereal contamination with moulds and their toxic methabolites.

X-ray mirror prototype based on cold shaping of thin glass foils

NASA Astrophysics Data System (ADS)

Basso, Stefano; Civitani, Marta; Ghigo, Mauro; Hołyszko, Joanna; Pareschi, Giovanni; Salmaso, Bianca; Vecchi, Gabriele; Burwitz, Vadim; Pelliciari, Carlo; Hartner, Gisela D.; Breunig, Elias

2017-08-01

The Slumping Glass Optics technology for the fabrication of astronomical X-ray mirrors has been developed in recent years in USA and Europe. The process has been used for making the mirrors of the Nustar, mission. The process starts with very thin glass foils hot formed to copy the profile of replication moulds. At INAF - Osservatorio Astronomico di Brera a process based on cold shaping is being developed, based on an integration method involving the use of interconnecting ribs for making stacks. Each glass foil in the stack is shaped onto a very precise integration mould and the correct shape is frozen by means of glued ribs that act as spacers between one layer and the next one (the first layers being attached to a thick substrate). Therefore, the increasing availability of flexible glass foils with a thickness of a few tens of microns (driven by electronic market for ultra-thin displays) opens new possibilities for the fabrication of X-ray mirrors. This solution appears interesting especially for the fabrication of mirrors for hard X-rays (with energy > 10 keV) based on multilayer coatings, taking advantage from the intrinsic low roughness of the glass foils that should grant a low scattering level. The stress frozen on the glass due to the cold shaping is not negligible, but it is kept into account in the errors of the X-ray optics design. As an exercise, we have considered the requirements and specs of the FORCE hard Xray mission concept (being studied by JAXA) and we have designed the mirror modules assuming the cold slumping as a fabrication method. In the meantime, a prototype (representative of the FORCE mirror modules) is being design and integrated in order to demonstrate the feasibility and the capacity to reach good angular resolution.

A method for increase abrasive wear resistance parts by obtaining on methods casting on gasifying models

NASA Astrophysics Data System (ADS)

Sedukhin, V. V.; Anikeev, A. N.; Chumanov, I. V.

2017-11-01

Method optimizes hardening working layer parts’, working in high-abrasive conditions looks in this work: bland refractory particles WC and TiC in respect of 70/30 wt. % prepared by beforehand is applied on polystyrene model in casting’ mould. After metal poured in mould, withstand for crystallization, and then a study is carried out. Study macro- and microstructure received samples allows to say that thickness and structure received hardened layer depends on duration interactions blend harder carbides and liquid metal. Different character interactions various dispersed particles and matrix metal observed under the same conditions. Tests abrasive wear resistance received materials of method calculating residual masses was conducted in laboratory’ conditions. Results research wear resistance showed about that method obtaining harder coating of blend carbide tungsten and carbide titanium by means of drawing on surface foam polystyrene model before moulding, allows receive details with surface has wear resistance in 2.5 times higher, than details of analogy steel uncoated. Wherein energy costs necessary for transformation units mass’ substances in powder at obtained harder layer in 2.06 times higher, than materials uncoated.

Diversity Profile and Dynamics of Peptaibols Produced by Green Mould Trichoderma Species in Interactions with Their Hosts Agaricus bisporus and Pleurotus ostreatus.

PubMed

Marik, Tamás; Urbán, Péter; Tyagi, Chetna; Szekeres, András; Leitgeb, Balázs; Vágvölgyi, Máté; Manczinger, László; Druzhinina, Irina S; Vágvölgyi, Csaba; Kredics, László

2017-06-01

Certain Trichoderma species are causing serious losses in mushroom production worldwide. Trichoderma aggressivum and Trichoderma pleuroti are among the major causal agents of the green mould diseases affecting Agaricus bisporus and Pleurotus ostreatus, respectively. The genus Trichoderma is well-known for the production of bioactive secondary metabolites, including peptaibols, which are short, linear peptides containing unusual amino acid residues and being synthesised via non-ribosomal peptide synthetases (NRPSs). The aim of this study was to get more insight into the peptaibol production of T. aggressivum and T. pleuroti. HPLC/MS-based methods revealed the production of peptaibols closely related to hypomurocins B by T. aggressivum, while tripleurins representing a new group of 18-residue peptaibols were identified in T. pleuroti. Putative NRPS genes enabling the biosynthesis of the detected peptaibols could be found in the genomes of both Trichoderma species. In vitro experiments revealed that peptaibols are potential growth inhibitors of mushroom mycelia, and that the host mushrooms may have an influence on the peptaibol profiles of green mould agents. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Rapid evaluation technique to differentiate mushroom disease-related moulds by detecting microbial volatile organic compounds using HS-SPME-GC-MS.

PubMed

Radványi, Dalma; Gere, Attila; Jókai, Zsuzsa; Fodor, Péter

2015-01-01

Headspace solid-phase microextraction (HS-SPME) coupled with gas chromatography-mass spectrometry (GC-MS) was used to analyse microbial volatile organic compounds (MVOCs) of mushroom disease-related microorganisms. Mycogone perniciosa, Lecanicillum fungicola var. fungicola, and Trichoderma aggressivum f. europaeum species, which are typically harmful in mushroom cultivation, were examined, and Agaricus bisporus (bisporic button mushroom) was also examined as a control. For internal standard, a mixture of alkanes was used; these were introduced as the memory effect of primed septa in the vial seal. Several different marker compounds were found in each sample, which enabled us to distinguish the different moulds and the mushroom mycelium from each other. Monitoring of marker compounds enabled us to investigate the behaviour of moulds. The records of the temporal pattern changes were used to produce partial least squares regression (PLS-R) models that enabled determination of the exact time of contamination (the infection time of the media). Using these evaluation techniques, the presence of mushroom disease-related fungi can be easily detected and monitored via their emitted MVOCs.

Fatal Hormonema dematioides Peritonitis in a Patient on Continuous Ambulatory Peritoneal Dialysis: Criteria for Organism Identification and Review of Other Known Fungal Etiologic Agents

PubMed Central

Shin, Jong Hee; Lee, Sang Ku; Suh, Soon Pal; Ryang, Dong Wook; Kim, Nam Ho; Rinaldi, Michael G.; Sutton, Deanna A.

1998-01-01

We report a fatal case a fungal peritonitis caused by the yeast-like dematiaceous mould Hormonema dematioides in a 45-year-old woman. The woman had a 13-year history of insulin-dependent diabetes mellitus and had been on continuous ambulatory peritoneal dialysis for chronic renal failure. H. dematioides was repeatedly isolated from the dialysate culture specimens collected on days 3, 9, 16, and 20 of her hospital stay. Preliminary culture reports on day 7 of the growth of a yeast-like fungus, a probable Candida species, prompted the administration of fluconazole (FLU). Intraperitoneal and intravenous FLU failed to eliminate the mould, and the patient expired on day 21 of her hospital stay. We use this case to present what appears to be the first report of fungal peritonitis due to H. dematioides, to provide laboratorians with criteria for differentiating this organism from the similar mould Aureobasidium pullulans and from various yeast genera, and to provide a review of known fungal taxa inciting peritonitis. PMID:9650991

Reprint of "Characterisation and modelling of the thermorheological properties of pharmaceutical polymers and their blends using capillary rheometry: Implications for hot melt processing of dosage forms".

PubMed

Jones, David S; Margetson, Daniel N; McAllister, Mark S; Andrews, Gavin P

2015-12-30

Given the growing interest in thermal processing methods, this study describes the use of an advanced rheological technique, capillary rheometry, to accurately determine the thermorheological properties of two pharmaceutical polymers, Eudragit E100 (E100) and hydroxypropylcellulose JF (HPC) and their blends, both in the presence and absence of a model therapeutic agent (quinine, as the base and hydrochloride salt). Furthermore, the glass transition temperatures (Tg) of the cooled extrudates produced using capillary rheometry were characterised using Dynamic Mechanical Thermal Analysis (DMTA) thereby enabling correlations to be drawn between the information derived from capillary rheometry and the glass transition properties of the extrudates. The shear viscosities of E100 and HPC (and their blends) decreased as functions of increasing temperature and shear rates, with the shear viscosity of E100 being significantly greater than that of HPC at all temperatures and shear rates. All platforms were readily processed at shear rates relevant to extrusion (approximately 200-300s(-1)) and injection moulding (approximately 900s(-1)). Quinine base was observed to lower the shear viscosities of E100 and E100/HPC blends during processing and the Tg of extrudates, indicative of plasticisation at processing temperatures and when cooled (i.e. in the solid state). Quinine hydrochloride (20% w/w) increased the shear viscosities of E100 and HPC and their blends during processing and did not affect the Tg of the parent polymer. However, the shear viscosities of these systems were not prohibitive to processing at shear rates relevant to extrusion and injection moulding. As the ratio of E100:HPC increased within the polymer blends the effects of quinine base on the lowering of both shear viscosity and Tg of the polymer blends increased, reflecting the greater solubility of quinine within E100. In conclusion, this study has highlighted the importance of capillary rheometry in identifying processing conditions, polymer miscibility and plasticisation phenomena. Copyright © 2015. Published by Elsevier B.V.

Characterisation and modelling of the thermorheological properties of pharmaceutical polymers and their blends using capillary rheometry: Implications for hot melt processing of dosage forms.

PubMed

Jones, David S; Margetson, Daniel N; McAllister, Mark S; Andrews, Gavin P

2015-09-30

Given the growing interest in thermal processing methods, this study describes the use of an advanced rheological technique, capillary rheometry, to accurately determine the thermorheological properties of two pharmaceutical polymers, Eudragit E100 (E100) and hydroxypropylcellulose JF (HPC) and their blends, both in the presence and absence of a model therapeutic agent (quinine, as the base and hydrochloride salt). Furthermore, the glass transition temperatures (Tg) of the cooled extrudates produced using capillary rheometry were characterised using Dynamic Mechanical Thermal Analysis (DMTA) thereby enabling correlations to be drawn between the information derived from capillary rheometry and the glass transition properties of the extrudates. The shear viscosities of E100 and HPC (and their blends) decreased as functions of increasing temperature and shear rates, with the shear viscosity of E100 being significantly greater than that of HPC at all temperatures and shear rates. All platforms were readily processed at shear rates relevant to extrusion (approximately 200-300 s(-1)) and injection moulding (approximately 900 s(-1)). Quinine base was observed to lower the shear viscosities of E100 and E100/HPC blends during processing and the Tg of extrudates, indicative of plasticisation at processing temperatures and when cooled (i.e. in the solid state). Quinine hydrochloride (20% w/w) increased the shear viscosities of E100 and HPC and their blends during processing and did not affect the Tg of the parent polymer. However, the shear viscosities of these systems were not prohibitive to processing at shear rates relevant to extrusion and injection moulding. As the ratio of E100:HPC increased within the polymer blends the effects of quinine base on the lowering of both shear viscosity and Tg of the polymer blends increased, reflecting the greater solubility of quinine within E100. In conclusion, this study has highlighted the importance of capillary rheometry in identifying processing conditions, polymer miscibility and plasticisation phenomena. Copyright © 2015. Published by Elsevier B.V.

Ho-doped Soft Glass Optical Fibers for Coherent Wavelength Sources Above 2 Micron

DTIC Science & Technology

2010-12-01

following glasses were prepared in order to fabricate a single-mode Tm-Ho doped optical fibre. Their composition is in mol% and the rare earth oxides ...in this work was 99+%. The onset melting temperature was 750 ˚C and the duration of the process 2 hours. The melt was cast in a brass mould...preheated to 300 ˚C and annealed at Tg – 10 ˚C for 2 h. Glass melting was carried out in a Pt crucible inside a chamber furnace. Core glass was melted

Optical coatings on polymers

NASA Astrophysics Data System (ADS)

Bauer, Thomas

2005-09-01

Optical transparent polymers are used for technical optics for more than 50 years and currently replace glass as optical material in several application fields. Optical functional coatings like mirrors, filters, beam splitters and anti-reflection coatings gain increasingly in importance. New light sources and head mounted systems need light and effective reflector designs. The paper gives an overview about vacuum coating technologies for metal and dielectric layers on polymers for technical optics. Especially for polymers controlling the complete process chain from injection moulding to storing, coating and shipping decides on the technological and commercial success.

Bio-composites based on cellulose acetate and kenaf fibers: Processing and properties

NASA Astrophysics Data System (ADS)

Pang, C.; Shanks, R. A.; Daver, F.

2014-05-01

Research on bio-composites is important because of its positive environmental impact. In this study, bio-composites based on plasticised cellulose acetate and kenaf fibers were prepared by solution casting and compression moulding methods. The fibers were chemically treated to remove lignin, hemicellulose and impurities. Mechanical, morphological and thermal properties of the bio-composites were studied. Introduction of chopped kenaf fibers increased the storage modulus. The flexural storage modulus of the composite was affected with the introduction of moisture. Moisture behaved similar to the effect of plasticiser, it reduced the modulus.

Response Ant Colony Optimization of End Milling Surface Roughness

PubMed Central

Kadirgama, K.; Noor, M. M.; Abd Alla, Ahmed N.

2010-01-01

Metal cutting processes are important due to increased consumer demands for quality metal cutting related products (more precise tolerances and better product surface roughness) that has driven the metal cutting industry to continuously improve quality control of metal cutting processes. This paper presents optimum surface roughness by using milling mould aluminium alloys (AA6061-T6) with Response Ant Colony Optimization (RACO). The approach is based on Response Surface Method (RSM) and Ant Colony Optimization (ACO). The main objectives to find the optimized parameters and the most dominant variables (cutting speed, feedrate, axial depth and radial depth). The first order model indicates that the feedrate is the most significant factor affecting surface roughness. PMID:22294914

Manufacturing and operational issues with lead-acid batteries

NASA Astrophysics Data System (ADS)

Rand, D. A. J.; Boden, D. P.; Lakshmi, C. S.; Nelson, R. F.; Prengaman, R. D.

An expert panel replies to questions on lead-acid technology and performance asked by delegates to the Ninth Asian Battery Conference. The subjects are as follows. Grid alloys: effects of calcium and tin levels on microstructure, corrosion, mechanical and electrochemical properties; effect of alloy-fabrication process on mechanical strength and corrosion resistance; low dross-make during casting of lead-calcium-tin alloys; future of book-mould casting; effect of increasing levels of silver; stability of continuously processed grids at high temperature. Negative-plate expanders: function of lignosulfonates and barium sulfate; benefits of pre-blended expanders; optimum expander formulations. Valve-regulated batteries: effect of oxygen cycle; optimum methods for float charging; charging and deep-cycle lifetimes; reliability testing.

Undercut feature recognition for core and cavity generation

NASA Astrophysics Data System (ADS)

Yusof, Mursyidah Md; Salman Abu Mansor, Mohd

2018-01-01

Core and cavity is one of the important components in injection mould where the quality of the final product is mostly dependent on it. In the industry, with years of experience and skill, mould designers commonly use commercial CAD software to design the core and cavity which is time consuming. This paper proposes an algorithm that detect possible undercut features and generate the core and cavity. Two approaches are presented; edge convexity and face connectivity approach. The edge convexity approach is used to recognize undercut features while face connectivity is used to divide the faces into top and bottom region.

International Towing Tank Conference ITTC Symbols and Terminology List. Final Version 1996

DTIC Science & Technology

1997-05-13

law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a currently valid OMB...of water-plane aft of mWA midship 2 A AWF Area of water-plane forward mWF of midship 2 A AX Area of maximum transverse mX section 2 B B Beam or...design water line B BWL Maximum moulded breadth mWL at design water line B BX Breadth, moulded of mX maximum section area at design water line d,T T

Endoglucanase production by paper-degrading mycoflora.

PubMed

Das, M K; Prasad, J S; Ahmad, S K

1997-11-01

Fourteen fungal species, namely Aspergillus flavus, A. fumigatus, A. niger, A. ustus, Penicillium islandicum, P. wortmannii, Memnoniella echinata, Cladosporium herbarum, Stachybotrys atra, Chaetomium globosum, Fusarium oxysporum, Torula herbarum, Alternaria alternata and Curvularia uncinata were isolated from different grades of paper. They differ in their distribution on various kinds of paper and also in relative occurrence. While seasonal influence on mycoflora was observed, most of the moulds were capable of growing in all three seasons examined (summer, winter, rainy season). The moulds were cellulolytic in nature and endoglucanase activity was greatest in Aspergillus flavus, A. niger, A. fumigatus, P. wortmannii and P. islandicum.

Influence of the intramedullary nail preparation method on nail's mechanical properties and degradation rate.

PubMed

Morawska-Chochół, Anna; Chłopek, Jan; Szaraniec, Barbara; Domalik-Pyzik, Patrycja; Balacha, Ewa; Boguń, Maciej; Kucharski, Rafael

2015-06-01

When it comes to the treatment of long bone fractures, scientists are still investigating new materials for intramedullary nails and different manufacturing methods. Some of the most promising materials used in the field are resorbable polymers and their composites, especially since there is a wide range of potential manufacturing and processing methods. The aim of this work was to select the best manufacturing method and technological parameters to obtain multiphase, and multifunctional, biodegradable intramedullary nails. All composites were based on a poly(l-lactide) matrix. Either magnesium alloy wires or carbon and alginate fibres were introduced in order to reinforce the nails. The polylactide matrix was also modified with tricalcium phosphate and gentamicin sulfate. The composite nails were manufactured using three different methods: forming from solution, injection moulding and hot pressing. The effect of each method of manufacturing on mechanical properties and degradation rate of the nails was evaluated. The study showed that injection moulding provides higher uniformity and homogeneity of the particle-modified polylactide matrix, whereas hot pressing favours applying higher volume fractions of fibres and their better impregnation with the polymer matrix. Thus, it was concluded that the fabrication method should be individually selected dependently on the nail's desired phase composition. Copyright © 2015 Elsevier B.V. All rights reserved.

The Influence of Injection Molding Parameter on Properties of Thermally Conductive Plastic

NASA Astrophysics Data System (ADS)

Hafizah Azis, N.; Zulafif Rahim, M.; Sa'ude, Nasuha; Rafai, N.; Yusof, M. S.; Tobi, ALM; Sharif, ZM; Rasidi Ibrahim, M.; Ismail, A. E.

2017-05-01

Thermally conductive plastic is the composite between metal-plastic material that is becoming popular because if it special characteristic. Injection moulding was regarded as the best process for mass manufacturing of the plastic composite due to its low production cost. The objective of this research is to find the best combination of the injection parameter setting and to find the most significant factor that effect the strength and thermal conductivity of the composite. Several parameter such as the volume percentage of copper powder, nozzle temperature and injection pressure of injection moulding machine were investigated. The analysis was done using Design Expert Software by implementing design of experiment method. From the analysis, the significant effects were determined and mathematical models of only significant effect were established. In order to ensure the validity of the model, confirmation run was done and percentage errors were calculated. It was found that the best combination parameter setting to maximize the value of tensile strength is volume percentage of copper powder of 3.00%, the nozzle temperature of 195°C and the injection pressure of 65%, and the best combination parameter settings to maximize the value of thermal conductivity is volume percentage of copper powder of 7.00%, the nozzle temperature of 195°C and the injection pressure of 65% as recommended..

Colour changes of orthodontic elastomeric module materials exposed to in vitro dietary media.

PubMed

Ardeshna, Anil P; Vaidyanathan, Tritala K

2009-09-01

To evaluate the colour stability of orthodontic elastomeric module material exposed to dietary media. An in vitro laboratory study. Coloured and clear orthodontic elastomeric modules from four companies were exposed to coffee, cola, tea and spices for 72 h. The difference in colour components was measured with a Minolta chromameter before and after exposure. Significant changes in colour, including grey level and chromaticity, both as a function of colour and company of elastomeric ligature module were found following exposure to beverages and spices. Colour change was most affected by Deltab* (yellowness) and most significant in clear modules. Modules made using injection mouldings were more resistant to colour change than those by extrusion. Spice mix had the most effect and cola beverage the least. Clinically, these changes compromised both colour stability and esthetics of the elastomeric module. Clinicians should make patients aware of the effect of consuming beverages and spices on the colour stability of their selected ligature modules. Clinicians should favour modules made with injection moulding. Darker colour modules may be preferred to clear modules to avoid excessive colour degradation through dietary media such as beverages and food spices. Patients consuming large amounts of spices or coffee should avoid clear modules made by extrusion processing because of their tendency to discolour.

Fabrication of cell container arrays with overlaid surface topographies.

PubMed

Truckenmüller, Roman; Giselbrecht, Stefan; Escalante-Marun, Maryana; Groenendijk, Max; Papenburg, Bernke; Rivron, Nicolas; Unadkat, Hemant; Saile, Volker; Subramaniam, Vinod; van den Berg, Albert; van Blitterswijk, Clemens; Wessling, Matthias; de Boer, Jan; Stamatialis, Dimitrios

2012-02-01

This paper presents cell culture substrates in the form of microcontainer arrays with overlaid surface topographies, and a technology for their fabrication. The new fabrication technology is based on microscale thermoforming of thin polymer films whose surfaces are topographically prepatterned on a micro- or nanoscale. For microthermoforming, we apply a new process on the basis of temporary back moulding of polymer films and use the novel concept of a perforated-sheet-like mould. Thermal micro- or nanoimprinting is applied for prepatterning. The novel cell container arrays are fabricated from polylactic acid (PLA) films. The thin-walled microcontainer structures have the shape of a spherical calotte merging into a hexagonal shape at their upper circumferential edges. In the arrays, the cell containers are arranged densely packed in honeycomb fashion. The inner surfaces of the highly curved container walls are provided with various topographical micro- and nanopatterns. For a first validation of the microcontainer arrays as in vitro cell culture substrates, C2C12 mouse premyoblasts are cultured in containers with microgrooved surfaces and shown to align along the grooves in the three-dimensional film substrates. In future stem-cell-biological and tissue engineering applications, microcontainers fabricated using the proposed technology may act as geometrically defined artificial microenvironments or niches.

Involvement of microbial mats in early fossilization by decay delay and formation of impressions and replicas of vertebrates and invertebrates

NASA Astrophysics Data System (ADS)

Iniesto, Miguel; Buscalioni, Ángela D.; Carmen Guerrero, M.; Benzerara, Karim; Moreira, David; López-Archilla, Ana I.

2016-05-01

Microbial mats have been hypothesized to improve the persistence and the preservation of organic remains during fossilization processes. We test this hypothesis with long-term experiments (up to 5.5 years) using invertebrate and vertebrate corpses. Once placed on mats, the microbial community coats the corpses and forms a three-dimensional sarcophagus composed of microbial cells and exopolymeric substances (EPS). This coverage provides a template for i) moulding superficial features, resulting in negative impressions, and ii) generating replicas. The impressions of fly setulae, fish scales and frog skin verrucae are shaped mainly by small cells in an EPS matrix. Microbes also replicate delicate structures such as the three successive layers that compose a fish eye. The sarcophagus protects the body integrity, allowing the persistence of inner organs such as the ovaries and digestive apparatus in flies, the swim bladder and muscles in fish, and the bone marrow in frog legs. This study brings strong experimental evidence to the idea that mats favour metazoan fossilization by moulding, replicating and delaying decay. Rapid burial has classically been invoked as a mechanism to explain exceptional preservation. However, mats may play a similar role during early fossilization as they can preserve complex features for a long time.

A gradiometric version of contactless inductive flow tomography: theory and first applications

PubMed Central

Wondrak, Thomas; Stefani, Frank

2016-01-01

The contactless inductive flow tomography (CIFT) is a measurement technique that allows reconstructing the flow of electrically conducting fluids by measuring the flow-induced perturbations of one or various applied magnetic fields and solving the underlying inverse problem. One of the most promising application fields of CIFT is the continuous casting of steel, for which the online monitoring of the flow in the mould would be highly desirable. In previous experiments at a small-scale model of continuous casting, CIFT has been applied to various industrially relevant problems, including the sudden changes of flow structures in case of argon injection and the influence of a magnetic stirrer at the submerged entry nozzle. The application of CIFT in the presence of electromagnetic brakes, which are widely used to stabilize the flow in the mould, has turned out to be more challenging due to the extreme dynamic range between the strong applied brake field and the weak flow-induced perturbations of the measuring field. In this paper, we present a gradiometric version of CIFT, relying on gradiometric field measurements, that is capable to overcome those problems and which seems, therefore, a promising candidate for applying CIFT in the steel casting industry. This article is part of the themed issue ‘Supersensing through industrial process tomography’. PMID:27185963

Liquid-crystalline aromatic-aliphatic copolyester bioresorbable polymers.

PubMed

de Oca, Horacio Montes; Wilson, Joanne E; Penrose, Andrew; Langton, David M; Dagger, Anthony C; Anderson, Melissa; Farrar, David F; Lovell, Christopher S; Ries, Michael E; Ward, Ian M; Wilson, Andrew D; Cowling, Stephen J; Saez, Isabel M; Goodby, John W

2010-10-01

The synthesis and characterisation of a series of liquid-crystalline aromatic-aliphatic copolyesters are presented. Differential scanning calorimetry showed these polymers have a glass transition temperature in the range 72 degrees C-116 degrees C. Polarised optical microscopy showed each polymer exhibits a nematic mesophase on heating to the molten state at temperatures below 165 degrees C. Melt processing is demonstrated by the production of injection moulded and compression moulded specimens with Young's modulus of 5.7 +/- 0.3 GPa and 2.3 +/- 0.3 GPa, respectively. Wide-angle X-ray scattering data showed molecular orientation is responsible for the increase of mechanical properties along the injection direction. Degradation studies in the temperature range 37 degrees C-80 degrees C are presented for one polymer of this series and a kinetic constant of 0.002 days(-1) is obtained at 37 degrees C assuming a first order reaction. The activation energy (83.4 kJ mol(-1)) is obtained following the Arrhenius analysis of degradation, showing degradation of this material is less temperature sensitive compared with other commercially available biodegradable polyesters. In vitro and in vivo biocompatibility data are presented and it is shown the unique combination of degradative, mechanical and biological properties of these polymers may represent in the future an alternative for medical device manufacturers. Copyright 2010 Elsevier Ltd. All rights reserved.

An automated optofluidic biosensor platform combining interferometric sensors and injection moulded microfluidics.

PubMed

Szydzik, C; Gavela, A F; Herranz, S; Roccisano, J; Knoerzer, M; Thurgood, P; Khoshmanesh, K; Mitchell, A; Lechuga, L M

2017-08-08

A primary limitation preventing practical implementation of photonic biosensors within point-of-care platforms is their integration with fluidic automation subsystems. For most diagnostic applications, photonic biosensors require complex fluid handling protocols; this is especially prominent in the case of competitive immunoassays, commonly used for detection of low-concentration, low-molecular weight biomarkers. For this reason, complex automated microfluidic systems are needed to realise the full point-of-care potential of photonic biosensors. To fulfil this requirement, we propose an on-chip valve-based microfluidic automation module, capable of automating such complex fluid handling. This module is realised through application of a PDMS injection moulding fabrication technique, recently described in our previous work, which enables practical fabrication of normally closed pneumatically actuated elastomeric valves. In this work, these valves are configured to achieve multiplexed reagent addressing for an on-chip diaphragm pump, providing the sample and reagent processing capabilities required for automation of cyclic competitive immunoassays. Application of this technique simplifies fabrication and introduces the potential for mass production, bringing point-of-care integration of complex automated microfluidics into the realm of practicality. This module is integrated with a highly sensitive, label-free bimodal waveguide photonic biosensor, and is demonstrated in the context of a proof-of-concept biosensing assay, detecting the low-molecular weight antibiotic tetracycline.

Selection and evaluation of Debaryomyces hansenii isolates as potential bioprotective agents against toxigenic penicillia in dry-fermented sausages.

PubMed

Núñez, Félix; Lara, María S; Peromingo, Belén; Delgado, Josué; Sánchez-Montero, Lourdes; Andrade, María J

2015-04-01

Biocontrol using autochthonous Debaryomyces hansenii isolates is a potentially suitable strategy for inhibiting toxigenic moulds in dry-cured meat products. The antifungal activity of 280 D. hansenii isolated from dry-cured meat products as well as the mode of action of the most active isolates against toxigenic penicillia were evaluated in this work. A 13.9% of the D. hansenii isolates showed inhibitory activity in a radial inhibition assay. The effects on penicillia growth of both the cell-free culture filtrate and volatile compounds from active yeast isolates were analysed. Penicillia growth inhibition by D. hansenii was probably based on additive or synergistic effects of several inhibiting factors such as competition for nutrient and space, and production of soluble or volatile compounds. When four D. hansenii isolates were tested on dry-fermented sausage, two of them produced a significantly growth reduction of the ochratoxigenic Penicillium verrucosum, keeping its counts under the level considered as hazardous for the mycotoxin presence. Therefore, the use of these two D. hansenii isolates during the processing of dry-fermented meat product could be a promising tool to control toxigenic moulds in the meat industry. Copyright © 2014 Elsevier Ltd. All rights reserved.

Involvement of microbial mats in early fossilization by decay delay and formation of impressions and replicas of vertebrates and invertebrates

PubMed Central

Iniesto, Miguel; Buscalioni, Ángela D.; Carmen Guerrero, M.; Benzerara, Karim; Moreira, David; López-Archilla, Ana I.

2016-01-01

Microbial mats have been hypothesized to improve the persistence and the preservation of organic remains during fossilization processes. We test this hypothesis with long-term experiments (up to 5.5 years) using invertebrate and vertebrate corpses. Once placed on mats, the microbial community coats the corpses and forms a three-dimensional sarcophagus composed of microbial cells and exopolymeric substances (EPS). This coverage provides a template for i) moulding superficial features, resulting in negative impressions, and ii) generating replicas. The impressions of fly setulae, fish scales and frog skin verrucae are shaped mainly by small cells in an EPS matrix. Microbes also replicate delicate structures such as the three successive layers that compose a fish eye. The sarcophagus protects the body integrity, allowing the persistence of inner organs such as the ovaries and digestive apparatus in flies, the swim bladder and muscles in fish, and the bone marrow in frog legs. This study brings strong experimental evidence to the idea that mats favour metazoan fossilization by moulding, replicating and delaying decay. Rapid burial has classically been invoked as a mechanism to explain exceptional preservation. However, mats may play a similar role during early fossilization as they can preserve complex features for a long time. PMID:27162204

Power ultrasound in meat processing.

PubMed

Alarcon-Rojo, A D; Janacua, H; Rodriguez, J C; Paniwnyk, L; Mason, T J

2015-09-01

Ultrasound has a wide range of applications in various agricultural sectors. In food processing, it is considered to be an emerging technology with the potential to speed up processes without damaging the quality of foodstuffs. Here we review the reports on the applications of ultrasound specifically with a view to its use in meat processing. Emphasis is placed on the effects on quality and technological properties such as texture, water retention, colour, curing, marinating, cooking yield, freezing, thawing and microbial inhibition. After the literature review it is concluded that ultrasound is a useful tool for the meat industry as it helps in tenderisation, accelerates maturation and mass transfer, reduces cooking energy, increases shelf life of meat without affecting other quality properties, improves functional properties of emulsified products, eases mould cleaning and improves the sterilisation of equipment surfaces. Copyright © 2015 Elsevier Ltd. All rights reserved.

Minimizing makespan in a two-stage flow shop with parallel batch-processing machines and re-entrant jobs

NASA Astrophysics Data System (ADS)

Huang, J. D.; Liu, J. J.; Chen, Q. X.; Mao, N.

2017-06-01

Against a background of heat-treatment operations in mould manufacturing, a two-stage flow-shop scheduling problem is described for minimizing makespan with parallel batch-processing machines and re-entrant jobs. The weights and release dates of jobs are non-identical, but job processing times are equal. A mixed-integer linear programming model is developed and tested with small-scale scenarios. Given that the problem is NP hard, three heuristic construction methods with polynomial complexity are proposed. The worst case of the new constructive heuristic is analysed in detail. A method for computing lower bounds is proposed to test heuristic performance. Heuristic efficiency is tested with sets of scenarios. Compared with the two improved heuristics, the performance of the new constructive heuristic is superior.

Fungal DNA in hotel rooms in Europe and Asia--associations with latitude, precipitation, building data, room characteristics and hotel ranking.

PubMed

Norbäck, Dan; Cai, Gui-Hong

2011-10-01

There is little information on the indoor environment in hotels. Analysis of fungal DNA by quantitative PCR (qPCR) is a new method which can detect general and specific sequences. Dust was collected through swab sampling of door frames in 69 hotel rooms in 20 countries in Europe and Asia (2007-2009). Five sequences were detected by qPCR: total fungal DNA, Aspergillus and Penicillium DNA (Asp/Pen DNA), Aspergillus versicolor (A. versicolor DNA), Stachybotrys chartarum (S. chartarum DNA) and Streptomyces spp. (Streptomyces DNA). Associations were analysed by multiple linear regression. Total fungal DNA (GM = 1.08 × 10(8) cell equivalents m(-2); GSD = 6.36) and Asp/Pen DNA (GM = 1.79 × 10(7) cell equivalents m(-2); GSD = 10.12) were detected in all rooms. A. versicolor DNA, S. chartarum DNA and Streptomyces DNA were detected in 84%, 28% and 47% of the samples. In total, 20% of the rooms had observed dampness/mould, and 30% had odour. Low latitude (range 1.5-64.2 degrees) was a predictor of Asp/Pen DNA. Seaside location, lack of mechanical ventilation, and dampness or mould were other predictors of total fungal DNA and Asp/Pen DNA. Hotel ranking (Trip Advisor) or self-rated quality of the interior of the hotel room was a predictor of total fungal DNA, A. versicolor DNA and Streptomyces DNA. Odour was a predictor of S. chartarum DNA. In conclusion, fungal DNA in swab samples from hotel rooms was related to latitude, seaside location, ventilation, visible dampness and indoor mould growth. Hotels in tropical areas may have 10-100 times higher levels of common moulds such as Aspergillus and Penicillium species, as compared to a temperate climate zone.

Synergistic effect of the combined bio-fungicides ε-poly-l-lysine and chitooligosaccharide in controlling grey mould (Botrytis cinerea) in tomatoes.

PubMed

Sun, Guangzheng; Yang, Qichao; Zhang, Ancheng; Guo, Jia; Liu, Xinjie; Wang, Yang; Ma, Qing

2018-07-02

The antifungal properties and the induction of resistance by ε-poly-l-lysine (ε-PL) and chitooligosaccharide (COS) were examined to find an alternative to synthetic fungicides currently used in the control of the devastating fungal pathogen Botrytis cinerea, the causal agent of grey mould disease of tomatoes. As presented herein, this combined treatment (200 mg/L ε-PL + 400 mg/L COS) was found to have optimal in vitro antifungal activities, achieving an inhibition rate of 90.22%. In vivo assays with these combined bio-fungicides, under greenhouse conditions using susceptible tomato plants, demonstrated good protection against severe grey mould. In field tests, the combined bio-fungicides had a control effect of up to 66.67% against tomato grey mould. To elucidate the mechanisms of the combined bio-fungicide-induced resistance in the tomato, plants were subjected to three treatments: 1) inoculation with B. cinerea after spraying with 200 mg/L ε-PL alone, 2) inoculation with the combined bio-fungicides, and 3) inoculation with 400 mg/L COS alone. Compared to the control (sterile water), increases in salicylic acid (SA) and jasmonic acid (JA) levels and increased phenylalanine ammonia lyase (PAL), peroxidase (POD), and superoxide dismutase (SOD) activities were observed. Catalase (CAT) activity and abscisic acid (ABA) and gibberellin (GA) levels decreased, particularly in the combined bio-fungicide-treated plants. Altogether, these findings reveal that the combined bio-fungicides (200 mg/L ε-PL + 400 mg/L COS) should be an excellent biocontrol agent candidate that combines direct antifungal activity against B. cinerea with plant resistance. Copyright © 2018. Published by Elsevier B.V.

[Frequencies of airborne moulds in Zagreb].

PubMed

Segvić, Maja; Pepeljnjak, Stjepan

2004-06-01

Airborne fungi are sometimes associated with several respiratory diseases and allergies. This paper describes a study of qualitative and quantitative variations in the occurrence of airborne moulds in Zagreb area on three locations: centre of the city (C), Pharmaceutical Botanical Garden "Fran Kusan" (BG) and the mountain Medvednica (M) during autumn, winter, spring and summer 2002-03. Lower concentrations of airborne moulds were found in all three locations in autumn (up to 76.88 CFU/m3) and winter (31.46 CFU/m3), with significantly higher levels in C and BG than in M (P<0.001). In spring and summer, these concentrations were much higher in all sampling sites and were significantly higher in C (160.00 CFU/m3) and BG (134.00 CFU/m3) in spring than in M (90.07 CFU/m3) (P<0.001). In summer, significantly higher concentration was found in C (237.5 CFU/m3) than in BG (186.50 CFU/m3) (P<0.01), while concentrations in C and M (216.70 CFU/m3) were similar. Airspora belonging to 29 fungal genera were identified, and allergologicaly significant moulds, Cladosporium (up to 79.5%) and Alternaria (up to 59.4%) dominated in all sampling sites. Penicillium, Fusarium and Aspergillus were also constant fungal entities (43.0-70.5%), but in much lower concentrations than Cladosporium and Alternaria. Airsporas of Cladosporium and Alternaria were more frequent in spring and summer in all locations, with significantly higher concentrations in C and BG (P<0.05). The risk from allergies increases with higher airspora concentrations in spring and summer due to an increase in Cladosporium and Alternaria.

Biomedical microfluidic devices by using low-cost fabrication techniques: A review.

PubMed

Faustino, Vera; Catarino, Susana O; Lima, Rui; Minas, Graça

2016-07-26

One of the most popular methods to fabricate biomedical microfluidic devices is by using a soft-lithography technique. However, the fabrication of the moulds to produce microfluidic devices, such as SU-8 moulds, usually requires a cleanroom environment that can be quite costly. Therefore, many efforts have been made to develop low-cost alternatives for the fabrication of microstructures, avoiding the use of cleanroom facilities. Recently, low-cost techniques without cleanroom facilities that feature aspect ratios more than 20, for fabricating those SU-8 moulds have been gaining popularity among biomedical research community. In those techniques, Ultraviolet (UV) exposure equipment, commonly used in the Printed Circuit Board (PCB) industry, replaces the more expensive and less available Mask Aligner that has been used in the last 15 years for SU-8 patterning. Alternatively, non-lithographic low-cost techniques, due to their ability for large-scale production, have increased the interest of the industrial and research community to develop simple, rapid and low-cost microfluidic structures. These alternative techniques include Print and Peel methods (PAP), laserjet, solid ink, cutting plotters or micromilling, that use equipment available in almost all laboratories and offices. An example is the xurography technique that uses a cutting plotter machine and adhesive vinyl films to generate the master moulds to fabricate microfluidic channels. In this review, we present a selection of the most recent lithographic and non-lithographic low-cost techniques to fabricate microfluidic structures, focused on the features and limitations of each technique. Only microfabrication methods that do not require the use of cleanrooms are considered. Additionally, potential applications of these microfluidic devices in biomedical engineering are presented with some illustrative examples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Influence of high power ultrasound on selected moulds, yeasts and Alicyclobacillus acidoterrestris in apple, cranberry and blueberry juice and nectar.

PubMed

Režek Jambrak, Anet; Šimunek, Marina; Evačić, Silva; Markov, Ksenija; Smoljanić, Goran; Frece, Jadranka

2018-02-01

The purpose of this study was to investigate the effect of non-thermal technology, high power ultrasound (HPU) on inactivation of Aspergillus ochraceus 318, Penicillium expansum 565, Rhodotorula sp. 74, Saccharomyces cerevisiae 5 and Alicyclobacillus acidoterrestris DSM 3922 in clear juices and nectars from apple, blueberry and cranberry juice concentrate. Inoculated juice and nectars were treated by high power ultrasound (20kHz) according to procedure set by central composite design (CCD). Three operational parameters, amplitude (60, 90 and 120μm), temperature (20, 40 and 60°C), and treatment time (3, 6 or 9min) were varied in order to observe the influence of ultrasound and combination of ultrasound and slight heating (thermosonication) on growth and inactivation of selected microorganisms. Number of vegetative cells of A. acidoterrestris DSM 3922 were not significantly reduced by high power ultrasound (p>0.05), except in apple juice, where statistical significant (p<0.05) influence of quadratic interaction of amplitude on bacteria reduction were observed. In all samples of fruit juices and nectars in terms of ultrasonic treatment at 60°C and times of 3, 6 and 9min, regardless of the value of the amplitude, complete inactivation of the growth of yeasts and moulds were achieved, while at 20 and 40°C it is not observed. The value of reduction of cells of selected yeasts and moulds for ultrasound treatments at 60°C and the duration of the 3, 6 and 9min ranged from 3.556 to 5.934 log units, depending on the initial number of selected yeasts and moulds before treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of ethanol on growth of Chrysonilia sitophila ('the red bread mould') and Hyphopichia burtonii ('the chalky mould') in sliced bread.

PubMed

Berni, E; Scaramuzza, N

2013-10-01

Contamination of food industrial environments and recontamination of finished products by Chrysonilia sitophila and Hyphopichia burtonii have long represented serious problems for the bakery industries. As one of the most common ways to slow down or avoid fungal spoilage on bakery products is the use of ethanol, in the present work the effect of this substance has been assessed on growth of two of the most frequently occurring associated moulds, C. sitophila and H. burtonii, by means of tests on both synthetic media and sliced bread. Test on synthetic media: H. burtonii was less markedly affected in lag-phase duration and radial growth rates by the addition of ethanol to DG18 and the reduction in incubation temperature than C. sitophila that failed to grow at the highest concentrations of ethanol tested (2·0 and 4·0% at 15°C; 4·0% at 25°C). Test on sliced bread: ethanol proved to be effective to prevent spoilage by C. sitophila even at the lowest concentration tested (0·8%, w/w), while higher concentrations (2·0%, w/w) were needed to prevent spoilage by H. burtonii. This study shows that ethanol could represent an effective barrier to prevent spoilage of bakery products by associated moulds such as Chrysonilia sitophila and Hyphopichia burtonii, whose growth on packed and sliced bread was inhibited at very low (0·8%) or medium (2·0%) ethanol concentrations, respectively. The results obtained represent a fundamental point of reference for the bakery industries, as they can apply them in the productive practice to avoid spoilage by C. sitophila and H. burtonii on their products. © 2013 The Society for Applied Microbiology.

Measuring the significance of pearlescence in real-time bottle forming

NASA Astrophysics Data System (ADS)

Nixon, J.; Menary, G.; Yan, S.

2018-05-01

This work examines the optical properties of polyethylene terephthalate (PET) bottles during the stretch-blow-moulding (SBM) process. PET has a relatively large process window with regards to process parameters, however if the boundaries are pushed, the resultant bottle can become insufficient for consumer requirements. One aspect of this process is the onset of pearlescence in the bottle material, where the bottle becomes opaque due to elevated stress whitening. Experimental trials were carried out using a modified free-stretch-blow machine where the deforming bottle was examined in free air. The strain values of the deformation were measured using digital image correlation (DIC) and the optical properties were measured relative to the initial amorphous PET preform. The results reveal that process parameters can significantly affect pearlescence. The detrimental level of pearlescence may be predicted therefore reducing the probability of poorly formed bottles.

Microbiology of processed edible insect products - Results of a preliminary survey.

PubMed

Grabowski, Nils Th; Klein, Günter

2017-02-21

Little is known of the microbiology of processed insect products. The present survey analysed a total of n=38 samples of deep-fried and spiced (Acheta domesticus, Locusta migratoria, and Omphisa fuscidentalis), cooked in soy sauce ("tsukudani"; Oxya yezoensis, Vespula flaviceps, and Bombyx mori), dried (A. domesticus, L. migatoria, Alphitobius diaperinus, Tenebrio molitor, B. mori, Hermetia illucens, and Musca domestica), powdered (H. illucens, T. molitor) and other (incl. deep-frozen B. mori and honeybee pollen) insect products microbiologically (total bacterial count [TBC], Enterobacteriaceae, staphylococci, bacilli, and yeasts and moulds counts, salmonellae, Listeria monocytogenes, and Escherichia coli). Although each product type revealed a microbiological profile of its own, dried and powdered insects ("class I") displayed markedly higher counts than the deep-fried and cooked ones ("class II"). Thresholds between class I and II products were estimated at 4.0 (TBC), 1.0 (Enterobacteriaceae, yeasts and moulds), 2.5 (staphylococci), and 3.0lgcfu/g (bacilli). All samples were negative for salmonellae, L. monocytogenes, E. coli and Stapyhlococcus aureus, but dried and powdered insects, as well as pollen, contained B. cereus, coliforms, Serratia liquefaciens, Listeria ivanovii, Mucor spp., Aspergillus spp., Penicillium spp., and Cryptococcus neoformans. Comparing the results with the hygiene criteria for edible insects proposed by Belgium and the Netherlands, class I products failed to comply with many bacterial count limits despite the absence of classical food pathogens. Therefore, class I products should always be consumed after another heating step as indicated by the manufacturer, until drying techniques are able to ensure lower bacterial counts. Copyright © 2016 Elsevier B.V. All rights reserved.

Biocompatibility of Advanced Manufactured Titanium Implants-A Review.

PubMed

Sidambe, Alfred T

2014-12-19

Titanium (Ti) and its alloys may be processed via advanced powder manufacturing routes such as additive layer manufacturing (or 3D printing) or metal injection moulding. This field is receiving increased attention from various manufacturing sectors including the medical devices sector. It is possible that advanced manufacturing techniques could replace the machining or casting of metal alloys in the manufacture of devices because of associated advantages that include design flexibility, reduced processing costs, reduced waste, and the opportunity to more easily manufacture complex or custom-shaped implants. The emerging advanced manufacturing approaches of metal injection moulding and additive layer manufacturing are receiving particular attention from the implant fabrication industry because they could overcome some of the difficulties associated with traditional implant fabrication techniques such as titanium casting. Using advanced manufacturing, it is also possible to produce more complex porous structures with improved mechanical performance, potentially matching the modulus of elasticity of local bone. While the economic and engineering potential of advanced manufacturing for the manufacture of musculo-skeletal implants is therefore clear, the impact on the biocompatibility of the materials has been less investigated. In this review, the capabilities of advanced powder manufacturing routes in producing components that are suitable for biomedical implant applications are assessed with emphasis placed on surface finishes and porous structures. Given that biocompatibility and host bone response are critical determinants of clinical performance, published studies of in vitro and in vivo research have been considered carefully. The review concludes with a future outlook on advanced Ti production for biomedical implants using powder metallurgy.

Workers' exposure to bioaerosols from three different types of composting facilities.

PubMed

Bonifait, Laetitia; Marchand, Geneviève; Veillette, Marc; M'Bareche, Hamza; Dubuis, Marie-Eve; Pépin, Carole; Cloutier, Yves; Bernard, Yves; Duchaine, Caroline

2017-10-01

Composting is a natural dynamic biological process used to valorise putrescible organic matter. The composting process can involve vigorous movements of waste material piles, which release high concentrations of bioaerosols into the surrounding environment. There is a lack of knowledge concerning the dispersal of airborne microorganisms emitted by composting plants (CP) as well as the potential occupational exposure of composting workers. The aim of this study was to investigate the workers exposure to bioaerosols during working activities in three different types of composting facilities (domestic, manure, carcass) using two different quantification methods (cultivation and qPCR) for bacteria and moulds concentrations. As expected, even if there are differences between all CP frameworks, independently of the type of the raw compost used, the production of bioaerosols increases significantly during handling activities. Important concentrations of mesophilic moulds and mesophilic bacteria were noted in the working areas with a respective maximal concentration of 2.3 × 10 5 CFU/m 3 and 1.6 × 10 5 CFU/m 3 . A. fumigatus and thermophilic Actinomycetes were also detected in all working areas for the 3 CP. This study emphases the risks for workers to being in contact with aerosolized pathogens such as Mycobacterium and Legionella and more specifically, L. pneumophila. The presence of high concentration of these bacteria in CP suggests a potential occupational health risk. This study may lead to recommendations for the creation of limits for occupational exposure. There is a need for identifying the standards exposure limits to bioaerosols in CP and efficient recommendation for a better protection of workers' health.

Thermoplastic Composites Reinforced with Textile Grids: Development of a Manufacturing Chain and Experimental Characterisation

NASA Astrophysics Data System (ADS)

Böhm, R.; Hufnagl, E.; Kupfer, R.; Engler, T.; Hausding, J.; Cherif, C.; Hufenbach, W.

2013-12-01

A significant improvement in the properties of plastic components can be achieved by introducing flexible multiaxial textile grids as reinforcement. This reinforcing concept is based on the layerwise bonding of biaxially or multiaxially oriented, completely stretched filaments of high-performance fibers, e.g. glass or carbon, and thermoplastic components, using modified warp knitting techniques. Such pre-consolidated grid-like textiles are particularly suitable for use in injection moulding, since the grid geometry is very robust with respect to flow pressure and temperature on the one hand and possesses an adjustable spacing to enable a complete filling of the mould cavity on the other hand. The development of pre-consolidated textile grids and their further processing into composites form the basis for providing tailored parts with a large number of additional integrated functions like fibrous sensors or electroconductive fibres. Composites reinforced in that way allow new product groups for promising lightweight structures to be opened up in future. The article describes the manufacturing process of this new composite class and their variability regarding reinforcement and function integration. An experimentally based study of the mechanical properties is performed. For this purpose, quasi-static and highly dynamic tensile tests have been carried out as well as impact penetration experiments. The reinforcing potential of the multiaxial grids is demonstrated by means of evaluating drop tower experiments on automotive components. It has been shown that the load-adapted reinforcement enables a significant local or global improvement of the properties of plastic components depending on industrial requirements.

Fabrication of anti-adhesion surfaces on aluminium substrates of rubber plastic moulds using electrolysis plasma treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meng, Jianbing, E-mail: jianbingmeng@126.com; Dong, Xiaojuan; Wei, Xiuting

An anti-adhesion surface with a water contact angle of 167° was fabricated on aluminium samples of rubber plastic moulds by electrolysis plasma treatment using mixed electrolytes of C{sub 6}H{sub 5}O{sub 7}(NH{sub 4}){sub 3} and Na{sub 2}SO{sub 4}, followed by fluorination. To optimise the fabrication conditions, several important processing parameters such as the discharge voltage, discharge time, concentrations of supporting electrolyte and stearic acid ethanol solution were examined systematically. Using scanning electron microscopy (SEM) to analyse surfaces morphology, micrometer scale pits, and protrusions were found on the surface, with numerous nanometer mastoids contained in the protrusions. These binary micro/nano-scale structures, whichmore » are similar to the micro-structures of soil-burrowing animals, play a critical role in achieving low adhesion properties. Otherwise, the anti-adhesion behaviours of the resulting samples were analysed by the atomic force microscope (AFM), Fourier-transform infrared spectrophotometer (FTIR), electrons probe micro-analyzer (EPMA), optical contact angle meter, digital Vickers microhardness (Hv) tester, and electronic universal testing. The results show that the electrolysis plasma treatment does not require complex processing parameters, using a simple device, and is an environment-friendly and effective method. Under the optimised conditions, the contact angle (CA) for the modified anti-adhesion surface is up to 167°, the sliding angle (SA) is less than 2°, roughness of the sample surface is only 0.409μm. Moreover, the adhesion force and H{sub v} are 0. 9KN and 385, respectively.« less

Physical properties and microstructure study of 316L SS fabricated by metal injection moulding process

NASA Astrophysics Data System (ADS)

Dandang, Nur Aidah Nabihah; Harun, Wan Sharuzi Wan; Khalil, Nur Zalikha; Ismail, Muhammad Hussain; Ibrahim, Rosdi

2017-12-01

Metal injection moulding (MIM) has been practised to process alloy powders to become components with significant physical and mechanical properties. Dissimilar than other methods, MIM focuses on the production of high volume, a small, and complex shape of products. The performance of the compacts depends on the suitable sintering parameters that governs their strengths in the final phase which determines the excellent properties of the sintered compacts. Three different sintering temperatures were utilised; 1100, 1200, and 1300 °C with two different soaking times; 1 and 3 hours at 10 °C/min heating rate to study their effect on the physical properties and microstructure analysis of 316L SS alloy compacts. The shrinkage measurement, surface roughness, and density measurement had been conducted for physical properties study. Different sintering temperatures give an effect to the physical properties of the sintered compacts. The shrinkage measurement at 1300 °C and 3-hour sintering condition demonstrated the highest percentage reading which was 10.1 % compared to the lowest percentage reading of 6.4 % at 1100 °C and 1-hour sintering conditions. Whereas, the minimum percentage of density measurement can be found at sintering conditions of 1100 °C and 1-hour which is 83.9 % and the highest percentage is at 1300 °C and 3-hour sintering condition which is about 89.51 %. Therefore, it has been determined that there could be a significant relationship between sintering temperature and physical properties in which it can be found from the porosity of the compact based on the microstructure studies.

Biocompatibility of Advanced Manufactured Titanium Implants—A Review

PubMed Central

Sidambe, Alfred T.

2014-01-01

Titanium (Ti) and its alloys may be processed via advanced powder manufacturing routes such as additive layer manufacturing (or 3D printing) or metal injection moulding. This field is receiving increased attention from various manufacturing sectors including the medical devices sector. It is possible that advanced manufacturing techniques could replace the machining or casting of metal alloys in the manufacture of devices because of associated advantages that include design flexibility, reduced processing costs, reduced waste, and the opportunity to more easily manufacture complex or custom-shaped implants. The emerging advanced manufacturing approaches of metal injection moulding and additive layer manufacturing are receiving particular attention from the implant fabrication industry because they could overcome some of the difficulties associated with traditional implant fabrication techniques such as titanium casting. Using advanced manufacturing, it is also possible to produce more complex porous structures with improved mechanical performance, potentially matching the modulus of elasticity of local bone. While the economic and engineering potential of advanced manufacturing for the manufacture of musculo-skeletal implants is therefore clear, the impact on the biocompatibility of the materials has been less investigated. In this review, the capabilities of advanced powder manufacturing routes in producing components that are suitable for biomedical implant applications are assessed with emphasis placed on surface finishes and porous structures. Given that biocompatibility and host bone response are critical determinants of clinical performance, published studies of in vitro and in vivo research have been considered carefully. The review concludes with a future outlook on advanced Ti production for biomedical implants using powder metallurgy. PMID:28788296

The Effect of Particles Shape and Size on Feedstock Flowibility and Chemical content of As-sintered NiTi Alloys

NASA Astrophysics Data System (ADS)

Kadir, R. A. Abdul; Razali, R.; Mohamad Nor, N. H.; Subuki, I.; Ismail, M. H.

2018-05-01

This paper presents a comparative study of two different titanium powders in fabrication of NiTi alloys by metal injection moulding (MIM) route. Two batches of powder mixture consisted of Ni-Ti and Ni-TiH2 with atomic ratio (at%) of 50-50 were prepared. TiH2 powder was used as a substitution for pure Ti powder owing to its relatively cheaper cost and has been claimed favourable in producing less impurity uptake in sintering process. The binder system used for both mixtures comprised of composite binder of palm stearin (PS) and polyethylene (PE) at weigth ratio (wt%) of 60-40. The flow behaviour of the mixtures was analysed using a capillary rheometer at different shear rates and temperatures. The results showed that owing to irregular shape of TiH2 compared to Ti powder, the viscosity of the feedstock was significantly higher, thus required greater temperature in order to improve the mouldability of the feedstock. Nevertheless, both feedstocks exhibited pseudoplastic, a shear thinning behavior with shear rate and temperature, desirable properties for injection moulding process. Samples prepared with Ni-Ti feedstock were sintered in a high vacuum furnace, while Ni-TiH2 feedstock was sintered in a tube furnace under a flowing of Argon gas. The results showed that the impurity contents (Carbon and Oxygen) for both feedstocks were almost comparable, suggesting NiTi alloy samples prepared with TiH2 powder is an attractive route for manufacturing of NiTi alloys.

Laboratory testing on infiltration in single synthetic fractures

NASA Astrophysics Data System (ADS)

Cherubini, Claudia; Pastore, Nicola; Li, Jiawei; Giasi, Concetta I.; Li, Ling

2017-04-01

An understanding of infiltration phenomena in unsaturated rock fractures is extremely important in many branches of engineering for numerous reasons. Sectors such as the oil, gas and water industries are regularly interacting with water seepage through rock fractures, yet the understanding of the mechanics and behaviour associated with this sort of flow is still incomplete. An apparatus has been set up to test infiltration in single synthetic fractures in both dry and wet conditions. To simulate the two fracture planes, concrete fractures have been moulded from 3D printed fractures with varying geometrical configurations, in order to analyse the influence of aperture and roughness on infiltration. Water flows through the single fractures by means of a hydraulic system composed by an upstream and a downstream reservoir, the latter being subdivided into five equal sections in order to measure the flow rate in each part to detect zones of preferential flow. The fractures have been set at various angles of inclination to investigate the effect of this parameter on infiltration dynamics. The results obtained identified that altering certain fracture parameters and conditions produces relevant effects on the infiltration process through the fractures. The main variables influencing the formation of preferential flow are: the inclination angle of the fracture, the saturation level of the fracture and the mismatch wavelength of the fracture.

[Subchronic toxicity testing of mold-ripened cheese].

PubMed

Schoch, U; Lüthy, J; Schlatter, C

1984-08-01

The biological effects of known mycotoxins of Penicillium roqueforti or P. camemberti and other still unknown, but potentially toxic metabolites in mould ripened cheese (commercial samples of Blue- and Camembert cheese) were investigated. High amounts of mycelium (equivalents of 100 kg cheese/man and day) were fed to mice in a subchronic feeding trial. The following parameters were determined: development of body weight, organ weights, hematology, blood plasma enzymes. No signs of adverse effects produced by cheese mycotoxins could be detected after 28 days. No still unknown toxic metabolites could be demonstrated. From these results no health hazard from the consumption of mould ripened cheese, even in high amounts, appears to exist.

The potential of Origanum vulgare L. (Lamiaceae) essential oil in inhibiting the growth of some food-related Aspergillus species

PubMed Central

Carmo, Egberto Santos; de Oliveira Lima, Edeltrudes; de Souza, Evandro Leite

2008-01-01

Origanum vulgare L. (Lamiaceae) has been currently known for their interesting antimicrobial activity being regarded as alternative antimicrobial for use is food conservation systems. This study aimed to evaluate the effectiveness of O. vulgare essential oil in inhibiting the growth of some food-related Aspergillus species (A. flavus, A. parasiticus, A. terreus, A. ochraceus, A. fumigatus and A. niger). The essential oil revealed a strong anti-Aspergillus property providing an inhibition of all assayed mould strains. MIC values were between 80 and 20 μL/mL being found a MIC50 of 40 μL/mL. The essential oil at concentration of 80 and 40 μL/mL provided a fungicidal effect on A. flavus, A. fumigatus and A. niger noted by a total inhibition of the radial mycelial growth along 14 days of interaction. In addition, the essential oil was able to inhibit the mould spores germination when assayed at concentrations of 80 and 40 μL/mL. Our results showed the interesting anti-Aspergillus activity of O. vulgare essential oil supporting their possible use as anti-mould compound in food conservation. PMID:24031231

Colloidal assembly directed by virtual magnetic moulds

NASA Astrophysics Data System (ADS)

Demirörs, Ahmet F.; Pillai, Pramod P.; Kowalczyk, Bartlomiej; Grzybowski, Bartosz A.

2013-11-01

Interest in assemblies of colloidal particles has long been motivated by their applications in photonics, electronics, sensors and microlenses. Existing assembly schemes can position colloids of one type relatively flexibly into a range of desired structures, but it remains challenging to produce multicomponent lattices, clusters with precisely controlled symmetries and three-dimensional assemblies. A few schemes can efficiently produce complex colloidal structures, but they require system-specific procedures. Here we show that magnetic field microgradients established in a paramagnetic fluid can serve as `virtual moulds' to act as templates for the assembly of large numbers (~108) of both non-magnetic and magnetic colloidal particles with micrometre precision and typical yields of 80 to 90 per cent. We illustrate the versatility of this approach by producing single-component and multicomponent colloidal arrays, complex three-dimensional structures and a variety of colloidal molecules from polymeric particles, silica particles and live bacteria and by showing that all of these structures can be made permanent. In addition, although our magnetic moulds currently resemble optical traps in that they are limited to the manipulation of micrometre-sized objects, they are massively parallel and can manipulate non-magnetic and magnetic objects simultaneously in two and three dimensions.

Effects of different strains Penicillium nalgiovense in the Nalžovy cheese during ripening.

PubMed

Mrázek, Josef; Pachlová, Vendula; Buňka, František; Černíková, Michaela; Dráb, Vladimír; Bejblová, Martina; Staněk, Karel; Buňková, Leona

2016-05-01

The present study examined the influence of eight selected strains of Penicillium nalgiovense as secondary culture on the ripening of soft mould cheese. Ion-exchange chromatography, SDS-PAGE and sensory analysis were used for comparison of P. nalgiovense with common secondary mould culture (Penicillium camemberti). Proteolytic activity was more intensive in the case of the strains of P. nalgiovense in comparison with the control strains of P. camemberti. Some differences in the proportion and amount of free amino acids were observed between the strains of P. nalgiovense during ripening. Lower proteolytic activity of P. nalgiovense was more desirable for sensory properties of cheese, especially in case sample N2. This study provides information on the usability of selected strains of P. nalgiovense that could support the development of sensory properties of mould-ripened soft cheese. The cheese with the culture N2 had the best flavour after 35 days of storage. Moreover, this strain showed the lowest bitterness in comparison with the other used P. nalgiovense cultures. The intensity of bitterness of sample N2 was comparable to that of the control sample with P. camemberti. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Laser-assisted electrochemical micromachining of mould cavity on the stainless steel surface

NASA Astrophysics Data System (ADS)

Li, Xiaohai; Wang, Shuming; Wang, Dong; Tong, Han

2018-02-01

In order to fabricate the micro mould cavities with complex structures on 304 stainless steel, laser-assisted electrochemical micromachining (EMM) based on surface modification by fiber laser masking was studied,and a new device of laser-assisted EMM was developed. Laser marking on the surface of 304 stainless steel can first be realized by fiber laser heating scanning. Through analysis of X ray diffraction analysis (XRD), metal oxide layer with predefined pattern can be formed by laser marking, and phase transformation can also occur on the 304 stainless steel surface, which produce the laser masking layer with corrosion resistance. The stainless steel surface with laser masking layer is subsequently etched by EMM, the laser masking layer severs as the temporary protective layer without relying on lithography mask, the fabrication of formed electrodes is also avoided, so micro pattern cavities can fast be fabricated. The impacts on machining accuracy during EMM with laser masking were discussed to optimize machining parameters, such as machining voltage, electrolyte concentration, duty cycle of pulse power supply and electrode gap size, the typical mould cavities 23μm deep were fabricated under the optimized parameters.

Lactic acid bacteria with potential to eliminate fungal spoilage in foods.

PubMed

Rouse, S; Harnett, D; Vaughan, A; van Sinderen, D

2008-03-01

To investigate antifungal activity produced by lactic acid bacteria (LAB) isolated from malted cereals and to determine if such LAB have the capacity to prevent fungal growth in a particular food model system. The effect of pH, temperature and carbon source on production of antifungal activity by four LAB was determined. Pediococcus pentosaceus was used to conduct a trial to determine if it is feasible to eliminate Penicillium expansum, the mould responsible for apple rot, using an apple model. Penicillium expansum was incapable of growth during the trial on apple-based agar plates inoculated with the antifungal-producing culture, whereas the mould did grow on apple plates inoculated with an LAB possessing no antifungal activity. Partial characterization of the antifungal compounds indicates that their activity is likely to be because of production of antifungal peptides. The trial conducted showed that the antifungal culture has the ability to prevent growth of the mould involved in apple spoilage, using apples as a model. The ability of an LAB to prevent growth of Pen. expansum using the apple model suggests that these antifungal LAB have potential applications in the food industry to prevent fungal spoilage of food.

Rapid identification of moulds and arthroconidial yeasts from positive blood cultures by MALDI-TOF mass spectrometry.

PubMed

de Almeida, João N; Sztajnbok, Jaques; da Silva, Afonso Rafael; Vieira, Vinicius Adriano; Galastri, Anne Layze; Bissoli, Leandro; Litvinov, Nadia; Del Negro, Gilda Maria Barbaro; Motta, Adriana Lopes; Rossi, Flávia; Benard, Gil

2016-11-01

Moulds and arthroconidial yeasts are potential life-threatening agents of fungemia in immunocompromised patients. Fast and accurate identification (ID) of these pathogens hastens initiation of targeted antifungal therapy, thereby improving the patients' prognosis. We describe a new strategy that enabled the identification of moulds and arthroconidial yeasts directly from positive blood cultures by MALDI-TOF mass spectrometry (MS). Positive blood cultures (BCs) with Gram staining showing hyphae and/or arthroconidia were prospectively selected and submitted to an in-house protein extraction protocol. Mass spectra were obtained by Vitek MS™ system, and identifications were carried out with in the research use only (RUO) mode with an extended database (SARAMIS™ [v.4.12] plus in-house database). Fusarium solani, Fusarium verticillioides, Exophiala dermatitidis, Saprochaete clavata, and Trichosporon asahii had correct species ID by MALDI-TOF MS analysis of positive BCs. All cases were related to critically ill patients with high mortality fungemia and direct ID from positive BCs was helpful for rapid administration of targeted antifungal therapy. © The Author 2016. Published by Oxford University Press on behalf of The International Society for Human and Animal Mycology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Effect of weld line positions on the tensile deformation of two-component metal injection moulding

NASA Astrophysics Data System (ADS)

Manonukul, Anchalee; Songkuea, Sukrit; Moonchaleanporn, Pongporn; Tange, Makiko

2017-12-01

Knowledge of the mechanical properties of two-component parts is critical for engineering functionally graded components. In this study, mono- and two-component tensile test specimens were metal injection moulded. Three different weld line positions were generated in the two-component specimens. Linear shrinkage of the two-component specimens was greater than that of the mono-component specimens because the incompatibility of sintering shrinkage of both materials causes biaxial stresses and enhances sintering. The mechanical properties of 316L stainless steel were affected by the addition of a coloured pigment used to identify the weld line position after injection moulding. For the two-component specimens, the yield stress and ultimate tensile stress were similar to those of 316L stainless steel. Because 316L and 630 (also known as 17-4PH) stainless steels were well-sintered at the interface, the mechanical properties of the weaker material (316L stainless steel) were dominant. However, the elongations of the two-component specimens were lower than those of the mono-component specimens. An interfacial zone with a microstructure that differed from those of the mono-material specimens was observed; its different microstructure was attributed to the gradual diffusion of nickel and copper.

Determination of microbial contamination of plastic cups for dairy products and utilization of electron beam treatment for sterilization.

PubMed

Tacker, M; Hametner, C; Wepner, B

2002-01-01

Packaging materials are often considered a critical control point in HACCP systems of food companies. Methods for the determination of the microbial contamination rate of plastic cups, especially for dairy products, must reliably detect single moulds, yeasts or coliforms. In this study, a comparison of a specially adapted coating method, impedance method, direct inoculation and membrane filter technique was carried out to determine contamination with yeasts, moulds, coliforms and total bacterial counts using the appropriate agar in each case. The coating method is recommended for determining yeasts, moulds and coliforms as it allows the localization of the microorganisms as well as the determination of single microorganisms. For total bacterial count, a direct inoculation technique is proposed. The employing of simple measures in the production and during transport of packaging materials, such as dust-prevention or tight sealing in polyethylene bags, heavily reduces microbial contamination rates of packaging material. To reduce contamination rates further, electron beam irradiation was applied: plastic cups sealed in polyethylene bags were treated with 4-5 kGy, a dose that already leads to sterile polystyrene and polypropylene cups without influencing mechanical characteristics of the packaging material.

Predictors of microbial agents in dust and respiratory health in the Ecrhs.

PubMed

Tischer, Christina; Zock, Jan-Paul; Valkonen, Maria; Doekes, Gert; Guerra, Stefano; Heederik, Dick; Jarvis, Deborah; Norbäck, Dan; Olivieri, Mario; Sunyer, Jordi; Svanes, Cecilie; Täubel, Martin; Thiering, Elisabeth; Verlato, Giuseppe; Hyvärinen, Anne; Heinrich, Joachim

2015-05-02

Dampness and mould exposure have been repeatedly associated with respiratory health. However, less is known about the specific agents provoking or arresting health effects in adult populations. We aimed to assess predictors of microbial agents in mattress dust throughout Europe and to investigate associations between microbial exposures, home characteristics and respiratory health. Seven different fungal and bacterial parameters were assessed in mattress dust from 956 adult ECRHS II participants in addition to interview based home characteristics. Associations between microbial parameters and the asthma score and lung function were examined using mixed negative binomial regression and linear mixed models, respectively. Indoor dampness and pet keeping were significant predictors for higher microbial agent concentrations in mattress dust. Current mould and condensation in the bedroom were significantly associated with lung function decline and current mould at home was positively associated with the asthma score. Higher concentrations of muramic acid were associated with higher mean ratios of the asthma score (aMR 1.37, 95%CI 1.17-1.61). There was no evidence for any association between fungal and bacterial components and lung function. Indoor dampness was associated with microbial levels in mattress dust which in turn was positively associated with asthma symptoms.

Direct hot slumping of thin glass foils for future generation x-ray telescopes: current state of the art and future outlooks

NASA Astrophysics Data System (ADS)

Salmaso, B.; Basso, S.; Brizzolari, C.; Civitani, M.; Ghigo, M.; Pareschi, G.; Spiga, D.; Tagliaferri, G.; Vecchi, G.

2017-11-01

To significantly improve the performances of the current X-ray observatories, the next generation of X-ray telescopes has to be characterized by a large effective area (Aeff { 2 m2 at 1 keV) and angular resolution better than 5 arcsec. The large dimension implied by these requirements forces the use of a modular approach, splitting the optics into segments. Moreover, lightweight materials, such as glass, have to be selected for the segmented optics in order to maintain a manageable weight for the optics. Since 2009 we are developing a direct hot slumping technique assisted by pressure, in which the glass optical surface is in contact with the mould and a pressure is applied in order to force the glass to copy the mould shape. A cold slumping step is used then to integrate the mirror segments into the final Wolter-I configuration. We present the state of the art of our hot slumping technology, comparing the results obtained with different glass types and mould materials. We also provide an overview of the possibilities of this technology also in view of future developments.

Asthma, Allergy and Eczema among Adults in Multifamily Houses in Stockholm (3-HE Study) - Associations with Building Characteristics, Home Environment and Energy Use for Heating

PubMed Central

Norbäck, Dan; Lampa, Erik; Engvall, Karin

2014-01-01

Risk factors for asthma, allergy and eczema were studied in a stratified random sample of adults in Stockholm. In 2005, 472 multifamily buildings (10,506 dwellings) were invited (one subject/dwelling) and 7,554 participated (73%). Associations were analyzed by multiple logistic regression, adjusting for gender, age, smoking, country of birth, income and years in the dwelling. In total, 11% had doctor's diagnosed asthma, 22% doctor's diagnosed allergy, 23% pollen allergy and 23% eczema. Doctor's diagnosed asthma was more common in dwellings with humid air (OR = 1.74) and mould odour (OR = 1.79). Doctor's diagnosed allergy was more common in buildings with supply exhaust air ventilation as compared to exhaust air only (OR = 1.45) and was associated with redecoration (OR = 1.48) and mould odour (OR = 2.35). Pollen allergy was less common in buildings using more energy for heating (OR = 0.75) and was associated with humid air (OR = 1.76) and mould odour (OR = 2.36). Eczema was more common in larger buildings (OR 1.07) and less common in buildings using more energy for heating (OR = 0.85) and was associated with water damage (OR = 1.47), humid air (OR = 1.73) and mould odour (OR = 2.01). Doctor's diagnosed allergy was less common in buildings with management accessibility both in the neighbourhood and in larger administrative divisions, as compared to management in the neighbourhood only (OR = 0.49; 95% CI 0.29–0.82). Pollen allergy was less common if the building maintenance was outsourced (OR = 0.67; 95% CI 0.51–0.88). Eczema was more common when management accessibility was only at the division level (OR = 1.49; 95% CI 1.06–2.11). In conclusions, asthma, allergy or eczema were more common in buildings using less energy for heating, in larger buildings and in dwellings with redecorations, mould odour, dampness and humid air. There is a need to reduce indoor chemical emissions and to control dampness. Energy saving may have consequences for allergy and eczema. More epidemiological studies are needed on building management organization. PMID:25479551

New species of Simona Moulds, 2012 and Chelapsalta Moulds, 2012 cicadas (Cicadidae: Cicadettinae: Cicadettini) from Australia: comparative morphology, songs, behaviour and distributions.

PubMed

Ewart, A; Popple, L W; Marshall, D C

2015-08-20

In 2012, Moulds established the morphologically similar cicada genera Simona and Chelapsalta, each with one Australian species (sancta Distant and puer Walker, respectively). In this paper, two new species are described within the genus Simona Moulds 2012, S. erema sp. nov. and S. retracta sp. nov., and one within the genus Chelapsalta Moulds 2012, C. myoporae sp. nov. The type species of Simona (female holotype), S. sancta (Distant, 1913), is redescribed based on a contemporary male, nominated a plesiotype, held in the Australian National Insect Collection. Melampsalta subgulosa Ashton 1914 is supported as a junior synonym of S. sancta. The species within the two genera of Simona and Chelapsalta are morphologically very similar. S. erema occurs widely through the arid regions of inland Australia, extending west from western Queensland through the Northern Territory, to central-western Western Australia, a linear distance of approximately 2200 km. S. retracta is known from a single semi-arid locality in southern inland Queensland. C. myoporae occurs widely through southeast, central and southwest Queensland, extending southwards into inland and western N.S.W. and southeastern South Australia. It tends to occur most commonly within vegetation associated with seasonal riverine floodplains, and in some areas of poorly drained and clay-rich soils. The calling songs of these three species, together with those of S. sancta and C. puer, are described. Detailed comparisons made of the songs of S. erema and C. myoporae, each from three widely separated locations, clearly exhibit structural consistency in their calling songs across their distributions. The Simona songs are complex and contain multiple elements; the species are very mobile and wary, and inhabit low dense shrubland. The songs of the two Chelapsalta species, both relatively sedentary in behaviour, in contrast consist of relatively uniform chirping and buzzing elements. It is suggested that, although the two genera are morphologically similar, the calling songs, behaviour and habitats do distinguish them, at least as represented by these species documented. MaxEnt modeling of the species climatic envelope for the widely distributed species Simona erema suggests an association with summer-peak rainfall and diurnal temperature range. Modeling under estimated conditions of the Last Glacial Maximum (22 ky) suggests the possibility of an even more widespread distribution at that time.

Flip-flop footwear with a moulded foot-bed for the treatment of foot pain: a randomised controlled trial.

PubMed

Chuter, Vivienne Helaine; Searle, Angela; Spink, Martin J

2016-11-11

Foot pain is a common problem affecting up to 1 in 5 adults and is known to adversely affect activities of daily living and health related quality of life. Orthopaedic footwear interventions are used as a conservative treatment for foot pain, although adherence is known to be low, in part due to the perception of poor comfort and unattractiveness of the footwear. The objective of this trial was to assess the efficacy of flip-flop style footwear (Foot Bio-Tec©) with a moulded foot-bed in reducing foot pain compared to participant's usual footwear. Two-arm parallel randomised controlled trial using computer generated random allocation schedule at an Australian university podiatry clinic. 108 volunteers with disabling foot pain were enrolled after responding to an advertisement and eligibility screening. Participants were randomly allocated to receive footwear education and moulded flip-flop footwear to wear as much as they were comfortable with for the next 12 weeks (n = 54) or footwear education and instructions to wear their normal footwear for the next 12 weeks (n = 54). Primary outcome was the pain domain of the Foot Health Status Questionnaire (FHSQ). Secondary outcomes were the foot function and general foot health domains of the FHSQ, a visual analogue scale (VAS) for foot pain and perceived comfort of the intervention footwear. Compared to the control group, the moulded flip-flop group showed a significant improvement in the primary outcome measure of the FHSQ pain domain (adjusted mean difference 8.36 points, 95 % CI 5.58 to 13.27, p < 0.01). Statistical and clinically significant differences were observed for the secondary measure of foot pain assessed by a VAS and the FSHQ domains of foot function and general foot health. None of the participants reported any pain or discomfort from the intervention footwear and six (footwear group = 4) were lost to follow up. Our results demonstrate that flip-flop footwear with a moulded foot-bed can have a significant effect on foot pain, function and foot health and might be a valuable adjunct therapy for people with foot pain. ACTRN12614000933651 . Retrospectively registered: 01/09/2014.

Evaluation of the PotoClean® decontamination technology for reprocessing of water supply lines in dental units during routine work

PubMed Central

Kramer, Axel; Koburger, Torsten; Taube, Lisa-Dorothea; Menzel, Michael; Meyer, Georg; Assadian, Ojan

2012-01-01

Background: A frequent problem in dental units is the microbial contamination of water and biofilm formation in the water supply lines. After random identification of a bacterial contaminated dental unit (310 cfu/ml) in a practise with 3 dental units we implemented the present study to evaluate the efficacy of the PotoClean® technology, based on anodic oxidation. Method: The efficacy of a regular low concentrated permanent decontamination (1 mg Cl/L) with an additional intensive decontamination by PotoClean® (three times 20 mg Cl/ml for 2 h) on three dental units was tested over 7 months. Microbial contamination, total chlorine concentration and redox potential have been analyzed. Dental unit A and B was 15 years old, unit C 5 years. Results: After 3 intensive decontaminations, in dental unit A and B the number of bacteria and moulds could be reduced less than 7 d. Thereafter the bacteria counts increased again during the subsequent 7 month period and the amount of moulds was with some exceptions 300 cfu/ml, although PotoClean® was constantly added in the system (1 mg Cl/L). After further 7.5 month only with low concentrated permanent disinfection (1 mg Cl/L) both units were successful decontaminated. Dental unit C represented an object which was easier to decontaminate because of the advanced construction (prevention of water stagnation) and the shorter useful life. At the beginning of the decontamination it was no bacterial contamination, but moulds were contained (300 cfu/ml). Already after the first intensive decontamination, no further bacteria and moulds could be detected. Discussion: An important factor for the efficacy of PotoClean® was the age of the units and their construction. For a new generation of dental units PotoClean® was effective during the whole period of monitoring. For two old types of dental unit with massive biofilm development the successful decontamination needed more than 7 month. Conclusion: The PotoClean® technology has resulted in even old-type turbines with intensive biofilm formation to complete decontamination. In a recent turbine design already after the first intensive decontamination with PotoClean® and its continuous use (1 mg Cl/L) no more contamination by bacteria and moulds were detectable. PMID:22558044

Evaluation of the PotoClean(®) decontamination technology for reprocessing of water supply lines in dental units during routine work.

PubMed

Kramer, Axel; Koburger, Torsten; Taube, Lisa-Dorothea; Menzel, Michael; Meyer, Georg; Assadian, Ojan

2012-01-01

A frequent problem in dental units is the microbial contamination of water and biofilm formation in the water supply lines. After random identification of a bacterial contaminated dental unit (310 cfu/ml) in a practise with 3 dental units we implemented the present study to evaluate the efficacy of the PotoClean(®) technology, based on anodic oxidation. The efficacy of a regular low concentrated permanent decontamination (1 mg Cl/L) with an additional intensive decontamination by PotoClean(®) (three times 20 mg Cl/ml for 2 h) on three dental units was tested over 7 months. Microbial contamination, total chlorine concentration and redox potential have been analyzed. Dental unit A and B was 15 years old, unit C 5 years. After 3 intensive decontaminations, in dental unit A and B the number of bacteria and moulds could be reduced less than 7 d. Thereafter the bacteria counts increased again during the subsequent 7 month period and the amount of moulds was with some exceptions 300 cfu/ml, although PotoClean(®) was constantly added in the system (1 mg Cl/L). After further 7.5 month only with low concentrated permanent disinfection (1 mg Cl/L) both units were successful decontaminated. Dental unit C represented an object which was easier to decontaminate because of the advanced construction (prevention of water stagnation) and the shorter useful life. At the beginning of the decontamination it was no bacterial contamination, but moulds were contained (300 cfu/ml). Already after the first intensive decontamination, no further bacteria and moulds could be detected. An important factor for the efficacy of PotoClean(®) was the age of the units and their construction. For a new generation of dental units PotoClean(®) was effective during the whole period of monitoring. For two old types of dental unit with massive biofilm development the successful decontamination needed more than 7 month. The PotoClean(®) technology has resulted in even old-type turbines with intensive biofilm formation to complete decontamination. In a recent turbine design already after the first intensive decontamination with PotoClean(®) and its continuous use (1 mg Cl/L) no more contamination by bacteria and moulds were detectable.

Measuring Thermoforming Behaviour

NASA Astrophysics Data System (ADS)

Michaeli, W.; Hopmann, C.; Ederleh, L.; Begemann, M.

2011-05-01

Thermoforming is the process of choice for manufacturing thin-gauge or large-area parts for packaging or technical applications. The process allows low-weight parts to be produced rapidly and economically from thermoplastic semi-finished products. A technical and consequently economical problem is the choice of the right material in combination with the thermoformability of the product. The prediction of thermoformability includes the aspired product features and geometry and defined wall thickness distributions, depending on the specific stretchability of the semifinished product. In practice, thermoformability is estimated by empirical tests with the particular semi-finished product using e.g. staged pyramidal moulds or model cars. With this method, it still cannot be ensured that the product can be thermoformed with the intended properties. A promising alternative is the forming simulation using finite element analysis (FEA). For the simulation, it is necessary to describe the material behaviour using defined material models and the appropriate parameters. Therefore, the stress-/strain-behaviour of the semi-finished product under defined conditions is required. There are several, entirely different measurement techniques used in industry and at research facilities. This paper compares a choice of different measurement techniques to provide an objective basis for future work and research. The semi-finished products are examined with the Membrane-Inflation-Rheometer (MIR), an equibiaxial strain rheometer. A flat sample is heated to the desired temperature in silicone oil. During the measurement, a servohydraulic linear drive advances a piston, thus displacing the hot silicone oil and inflating the specimen to form a sphere. Further measurements are carried out with the Karo IV Laboratory Stretching Machine at Brückner Maschinenbau GmbH & Co. KG, Siegsdorf, Germany. The samples are heated using hot air. During the biaxial stretching, the resulting forces at the clamps are measured. These techniques are compared to the stretching device developed at IKV. This measuring device is integrated into a laboratory thermoforming machine, which allows a close-to-real-process heating, handling and forming of the semi-finished products. After the heating with IR-radiation, force-displacement data is measured during the equibiaxial deformation. This work shows the differences between these methods and emphasises the particular benefits. Further measurement methods, like uniaxial tensile tests and plug deformation, and the effects on the forming simulation will be part of future research.

Effect of High-speed Milling tool path strategies on the surface roughness of Stavax ESR mold insert machining

NASA Astrophysics Data System (ADS)

Mebrahitom, A.; Rizuan, D.; Azmir, M.; Nassif, M.

2016-02-01

High speed milling is one of the recent technologies used to produce mould inserts due to the need for high surface finish. It is a faster machining process where it uses a small side step and a small down step combined with very high spindle speed and feed rate. In order to effectively use the HSM capabilities, optimizing the tool path strategies and machining parameters is an important issue. In this paper, six different tool path strategies have been investigated on the surface finish and machining time of a rectangular cavities of ESR Stavax material. CAD/CAM application of CATIA V5 machining module for pocket milling of the cavities was used for process planning.

Machinability of Stellite 6 hardfacing

NASA Astrophysics Data System (ADS)

Benghersallah, M.; Boulanouar, L.; Le Coz, G.; Devillez, A.; Dudzinski, D.

2010-06-01

This paper reports some experimental findings concerning the machinability at high cutting speed of nickel-base weld-deposited hardfacings for the manufacture of hot tooling. The forging work involves extreme impacts, forces, stresses and temperatures. Thus, mould dies must be extremely resistant. The aim of the project is to create a rapid prototyping process answering to forging conditions integrating a Stellite 6 hardfacing deposed PTA process. This study talks about the dry machining of the hardfacing, using a two tips machining tool and a high speed milling machine equipped by a power consumption recorder Wattpilote. The aim is to show the machinability of the hardfacing, measuring the power and the tip wear by optical microscope and white light interferometer, using different strategies and cutting conditions.

Experimental analysis of graphene nanocomposite on Kevlar

NASA Astrophysics Data System (ADS)

Manigandan, S.; Gunasekar, P.; Nithya, S.; Durga Revanth, G.; Anudeep, A. V. S. C.

2017-08-01

Graphene nanocomposite is a two dimensional structure which has intense role in material science. This paper investigates the topological property of the graphene nanocomposite doped in Kevlar fiber by direct mixing process. The Kevlar fiber by direct mixing process. The Kevlar fiber taken as the specimen which is fabricated by vacuum bag moulding process. Epoxy used as resin and HY951 as hardener. Three different specimens are fabricated based on the percentage of graphene nanocomposite 2%, 5%, 10% and 20% respectively. We witnessed the strength of the Kevlar fiber is increased when it is treated with nanocomposite. The percentage of the nanocomposite increase the strength of the fiber is increased. However as the nanocomposite beyond 5% the strength of fiber is dropped. In addition, we also seen the interfacial property of the fiber is dropped when the nanocomposite is added beyond threshold limit.

Hot melt extruded and injection moulded disulfiram-loaded PLGA millirods for the treatment of glioblastoma multiforme via stereotactic injection.

PubMed

McConville, Christopher; Tawari, Patricia; Wang, Weiguang

2015-10-15

Glioblastoma multiforme (GBM) has a poor prognosis and is one of the most common primary malignant brain tumours in adults. Stereotactic injections have been used to deliver chemotherapeutic drugs directly into brain tumours. This paper describes the development of disulfiram (DSF)-loaded biodegradable millirods manufactured using hot melt extrusion (HME) and injection moulding (IM). The paper demonstrates that the stability of the DSF within the millirods is dependent on the manufacturing technique used as well as the drug loading. The physical state of the DSF within the millirods was dependent on the fabrication process, with the DSF in the HME millirods being either completely amorphous within the PLGA, while the DSF within the IM millirods retained between 54 and 66% of its crystallinity. Release of DSF from the millirods was dependent on the degradation rate of the PLGA, the manufacturing technique used as well as the DSF loading. DSF in the 10% (w/w) DSF loaded HME millirods and the 20% (w/w) DSF-loaded HME and IM millirods had a similar cytotoxicity against a GBM cell line compared to the unprocessed DSF control. However, the 10% (w/w) DSF-loaded IM millirods had a significantly lower cytotoxicity when compared to the unprocessed control. Copyright © 2015 Elsevier B.V. All rights reserved.

In vitro bioactivity of micro metal injection moulded stainless steel with defined surface features.

PubMed

Bitar, Malak; Friederici, Vera; Imgrund, Philipp; Brose, Claudia; Bruinink, Arie

2012-05-04

Micrometre- and nanometre-scale surface structuring with ordered topography features may dramatically enhance orthopaedic implant integration. In this study we utilised a previously optimised micron metal injection moulding (µ-MIM) process to produce medical grade stainless steel surfaces bearing micrometre scale, protruding, hemispheres of controlled dimensions and spatial distribution. Additionally, the structured surfaces were characterised by the presence of submicrometre surface roughness resulting from metal grain boundary formation. Following cytocompatibility (cytotoxicity) evaluation using 3T3 mouse fibroblast cell line, the effect on primary human cell functionality was assessed focusing on cell attachment, shape and cytoskeleton conformation. In this respect, and by day 7 in culture, significant increase in focal adhesion size was associated with the microstructured surfaces compared to the planar control. The morphological conformation of the seeded cells, as revealed by fluorescence cytoskeleton labelling, also appeared to be guided in the vertical dimension between the hemisphere bodies. Quantitative evaluation of this guidance took place using live cytoplasm fluorescence labelling and image morphometry analysis utilising both, compactness and elongation shape descriptors. Significant increase in cell compactness was associated with the hemisphere arrays indicating collective increase in focused cell attachment to the hemisphere bodies across the entire cell population. Micrometre-scale hemisphere array patterns have therefore influenced cell attachment and conformation. Such influence may potentially aid in enhancing key cellular events such as, for example, neo-osteogenesis on implanted orthopaedic surfaces.

Mould spoilage of cereals during transportation by sea from Latin America to Europe mechanisms, impact and management.

PubMed

Mossel, D A

1988-12-01

Safe water contents of consignments of cereals to be shipped overseas can be calculated from the relation between mould-free storage time and storage conditions (temperature of the environment, aw of the cereal), corrected for heterogeneity of water distribution, content of damaged kernels and degree of infestation by insects. The validity of this model was substantiated by the inspection of shipments and theoretical data from the literature. This predictive model can usefully be substituted for previously used, ill-defined criteria like average or any portion's water content and should prompt the trade to sell consignments of cereals on the basis of dry substance.

Foaming of aluminium-silicon alloy using concentrated solar energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cambronero, L.E.G.; Ruiz-Roman, J.M.; Canadas, I.

2010-06-15

Solar energy is used for the work reported here as a nonconventional heating system to produce aluminium foam from Al-Si alloy precursors produced by powder metallurgy. A commercial precursor in cylindrical bars enclosed in a stainless-steel mould was heated under concentrated solar radiation in a solar furnace with varied heating conditions (heating rate, time, and temperature). Concentrated solar energy close to 300 W/cm{sup 2} on the mould is high enough to achieve complete foaming after heating for only 200 s. Under these conditions, the density and pore distribution in the foam change depending on the solar heating parameters and mouldmore » design. (author)« less

Evaluation of chitosans and Pichia guillermondii as growth inhibitors of Penicillium digitatum.

PubMed

Pacheco, Neith; Larralde-Corona, C Patricia; Sepulveda, Jose; Trombotto, Stéphan; Domard, Alain; Shirai, Keiko

2008-07-01

Chitosans were obtained by room-temperature-homogeneous-deacetylation (RTHD) and freeze-pump-out-thaw-heterogeneous-deacetylation (FPT) from chitins purified from fermentations. Commercial chitosan was deacetylated by three-FPT-cycles. Chitosans and Pichia guillermondii were evaluated on the growth of Penicillium digitatum. Medium molecular weight (M(W)) chitosans displayed higher inhibitory activity against the yeast than low M(W) biopolymers. Chitosans with low degree of acetylation (DA) were inhibitory for yeast and mould. Therefore, a low M(W) and high DA chitosan was selected for use against moulds combined with yeasts. Biopolymer and yeasts presented an additive effect, since chitosans were effective to delay spore germination, whereas yeast decreased apical fungal growth.

The manufacture of moulded supportive seating for the handicapped.

PubMed

Nelham, R L

1975-10-01

The wheelchair-bound population often have difficulty in obtaining a correct or comfortable posture in their chairs and sometimes develop pressure sores from long-duration sitting. This problem is being solved by manufacturing personalised, contoured seats which support the patient over the maximum area possible thereby reducing the pressure on the body and the incidence of pressure sores. A cast is obtained of the patient in a comfortable, medically correct posture and from this cast the seat is vacuum formed in thermoplastic materials or hand layed up in glass fibre reinforced resin. Some correction of deformity may be achieved. It is also possible to use the moulded seat in a vehicle.

Lightweight bio-composites based on hemp fibres produced by conventional and unconventional processes

NASA Astrophysics Data System (ADS)

Boccarusso, L.; Durante, M.; Formisano, A.; Langella, A.; Minutolo, F. Memola Capece

2017-10-01

Considering that nowadays the interest in the use of bio-composite materials is increasing more and more, this work is focused on the manufacturing of lightweight components based on hemp fibres for future applications, for example as a core for sandwich structures. Three different no-complex processes were used: a conventional hand lay-up, an unconventional infusion process and a hand lay-up process followed by injection moulding. They were used to produce bio-composite structures using an epoxy resin and/or a polyurethane foam as matrix. Depending on the process used for the manufacturing, laminates with different values of density were obtained. A detailed study in terms of both static and dynamic properties was carried out and the different mechanical behaviour for each sample typology was highlighted. The results showed that the process in which both the epoxy resin and the polyurethane foam were used as matrix allowed to obtain laminates with lower density and higher specific mechanical properties.

Advanced nondestructive techniques applied for the detection of discontinuities in aluminum foams

NASA Astrophysics Data System (ADS)

Katchadjian, Pablo; García, Alejandro; Brizuela, Jose; Camacho, Jorge; Chiné, Bruno; Mussi, Valerio; Britto, Ivan

2018-04-01

Metal foams are finding an increasing range of applications by their lightweight structure and physical, chemical and mechanical properties. Foams can be used to fill closed moulds for manufacturing structural foam parts of complex shape [1]; foam filled structures are expected to provide good mechanical properties and energy absorption capabilities. The complexity of the foaming process and the number of parameters to simultaneously control, demand a preliminary and hugely wide experimental activity to manufacture foamed components with a good quality. That is why there are many efforts to improve the structure of foams, in order to obtain a product with good properties. The problem is that even for seemingly identical foaming conditions, the effective foaming can vary significantly from one foaming trial to another. The variation of the foams often is related by structural imperfections, joining region (foam-foam or foam-wall mold) or difficulties in achieving a complete filling of the mould. That is, in a closed mold, the result of the mold filling and its structure or defects are not known a priori and can eventually vary significantly. These defects can cause a drastic deterioration of the mechanical properties [2] and lead to a low performance in its application. This work proposes the use of advanced nondestructive techniques for evaluating the foam distribution after filling the mold to improve the manufacturing process. To achieved this purpose ultrasonic technique (UT) and cone beam computed tomography (CT) were applied on plate and structures of different thicknesses filled with foam of different porosity. UT was carried out on transmission mode with low frequency air-coupled transducers [3], in focused and unfocused configurations.

Measurement and analysis of flow in 3D preforms for aerospace composites

NASA Astrophysics Data System (ADS)

Stewart, Andrew Lawrence

Composite materials have become viable alternatives to traditional engineering materials for many different product categories. Liquid transfer moulding (LTM) processes, specifically resin transfer moulding (RTM), is a cost-effective manufacturing technique for creating high performance composite parts. These parts can be tailor-made to their specific application by optimizing the properties of the textile preform. Preforms which require little or no further assembly work and are close to the shape of the final part are critical to obtaining high quality parts while simultaneously reducing labour and costs associated with other composite manufacturing techniques. One type of fabric which is well suited for near-net- shape preforms is stitched non-crimp fabrics. These fabrics offer very high in-plane strength and stiffness while also having increased resistance to delamination. Manufacturing parts from these dry preforms typically involves long-scale fluid flow through both open channels and porous fibre bundles. This thesis documents and analyzes the flow of fluid through preforms manufactured from non-crimp fabrics featuring through-thickness stitches. The objective of this research is to determine the effect of this type of stitch on the RTM injection process. All of the tests used preforms with fibre volume fractions representative of primary and secondary structural parts. A series of trials was conducted using different fibre materials, flow rates, fibre volumes fractions, and degrees of fibre consolidation. All of the trials were conducted for cases similar to RTM. Consolidation of the fibres showed improvements to both the thoroughness of the filling and to the fibre volume fraction. Experimentally determined permeability data was shown to trend well with simple models and precision of the permeability data was comparable to values presented by other authors who studied fabrics which did not feature the through-thickness stitches.

CFRP solutions for the innovative telescopes design

NASA Astrophysics Data System (ADS)

Rampini, Francesco; Marchiori, Gianpietro

2006-02-01

The new frontiers of the research in the astronomic field require the use of more and more advanced high-performance structures. Only an adequate technological innovation of conventional telescopes and radio-telescopes allow to obtain structures able to meet the new specification of the projects. Besides, technological innovation is founded not only on the identification of more and more sophisticated mechanisms and optical instruments, but also on the development of new materials and manufacturing processes for the entire structure that constitute an instrument such as a telescope or a radio-telescope. Among these materials, the use of the carbon fibre is highly important. This material, which is already widely used in the aerospace and automotive fields, shall join also the astronomic field for ground instruments. Thanks to the experience acquired with instruments like ALMA, the industry of composites is now able to guarantee different solutions at relatively low costs that allow the instruments of new generation to move extremely important steps in the development of scientific research. Not just materials, but also processes, through which the materials are worked and manufactured, are extremely important. The use of technologies, such as hand lay-up vacuum bag, compression moulding, table rolling of composite tubes, filament winding, poltrusion and Resin Transfer Moulding (RTM), allow to identify the ideal solution both for big dimension objects, such as backup structure, main mirror structure of quadripod legs, and relatively small objects, such as actuators, adjusters system, etc. The wide choice, concerning the use of composite materials, and their techniques of production, allow the technicians to satisfy the exigencies of astronomers be they addressed to simple control of the weights or of the stiffness of the structures, or to specific thermal behaviour of the piece itself.

Enhanced inhibition of Aspergillus niger on sedge (Lepironia articulata) treated with heat-cured lime oil.

PubMed

Matan, N; Matan, N; Ketsa, S

2013-08-01

This study aimed to examine heat curing effect (30-100°C) on antifungal activities of lime oil and its components (limonene, p-cymene, β-pinene and α-pinene) at concentrations ranging from 100 to 300 μl ml(-1) against Aspergillus niger in microbiological medium and to optimize heat curing of lime oil for efficient mould control on sedge (Lepironia articulata). Broth dilution method was employed to determine lime oil minimum inhibitory concentration, which was at 90 μl ml(-1) with heat curing at 70°C. Limonene, a main component of lime oil, was an agent responsible for temperature dependencies of lime oil activities observed. Response surface methodology was used to construct the mathematical model describing a time period of zero mould growth on sedge as functions of heat curing temperature and lime oil concentration. Heat curing of 90 μl ml(-1) lime oil at 70°C extended a period of zero mould growth on sedge to 18 weeks under moist conditions. Heat curing at 70°C best enhanced antifungal activity of lime oil against A. niger both in medium and on sedge. Heat curing of lime oil has potential to be used to enhance the antifungal safety of sedge products. © 2013 The Society for Applied Microbiology.

Protection of Historical Wood against Microbial Degradation-Selection and Application of Microbiocides.

PubMed

Koziróg, Anna; Rajkowska, Katarzyna; Otlewska, Anna; Piotrowska, Małgorzata; Kunicka-Styczyńska, Alina; Brycki, Bogumił; Nowicka-Krawczyk, Paulina; Kościelniak, Marta; Gutarowska, Beata

2016-08-22

The aim of this study was to select effective and safe microbiocides for the disinfection and protection of historical wooden surfaces at the former Auschwitz II-Birkenau concentration and extermination camp. We tested seven active compounds against bacteria and moulds, of which didecyldimethylammonium chloride and N-(3-aminopropyl)-N-dodecylpropane-1,3-diamine were effective even at 0.02%-2%. Subsequently, eight microbiocides containing the selected active ingredients were chosen and applied three times on the surface of wood samples colonized by bacteria and moulds. ABM-1 and ABM-2-6% solution; Rocima 101-8%; Preventol R 80-12%; Acticide 706 LV-15% and Boramon-30% were the most effective disinfectants. Under laboratory conditions, ABM-1, Boramon and Rocima 101 ensured antimicrobial protection of new wood samples for six months. In situ, 30% Boramon and 8% Rocima 101 applied by spraying effectively protected the historical wood from bacterial and mould growth for 12 and 3 months, respectively. Colour and luminance of the new wood were not altered after exposure to the biocides. Boramon and Rocima 101, applied by the spraying method, caused no significant change in the colour of the historical wood. Results from this study were used to develop a procedure for the protection of wood in historical buildings against biodeterioration.

Performance of mycology and histopathology tests for the diagnosis of toenail onychomycosis due to filamentous fungi: Dermatophyte and non-dermatophyte moulds.

PubMed

Lavorato, Fernanda G; Guimarães, Dávson A; Premazzi, Mario G; Piñeiro-Maceira, Juan M; Bernardes-Engemann, Andréa R; Orofino-Costa, Rosane

2017-09-01

Improvement of laboratory diagnosis of onychomychosis is important so that adequate treatment can be safely implemented. To evaluate and compare the performance of mycological and histopathological examinations in onychomycoses caused by dermatophyte and non-dermatophyte moulds. Patients with lateral/distal subungual onychomycosis in at least one hallux were enrolled in the protocol and assessed via mycological and histopathological tests. The isolation of filamentous fungi was considered the gold standard. Test performance was evaluated through sensitivity, specificity and positive and negative predictive values. A total of 212 patients were enrolled in the study. Direct microscopy (DM) was positive in 57.5% patients, and cultures in 34.4%. Among these patients, 23.3% were positive for dermatophytes, with Trichophyton rubrum the most frequently isolated, and 86.3% were positive for non-dermatophytes, with Neoscytalidium dimidiatum predominance. Histopathology was positive in 41.0% samples. Direct microscopy showed better sensitivity for non-dermatophyte moulds (P=.000) and nail clipping was more specific for dermatophyte (P=.018). Histopathology of the distal nail plate is a valuable complementary tool for the diagnosis of onychomycosis caused by dermatophytes and direct microscopy is especially useful for non-dermatophyte molds. © 2017 Blackwell Verlag GmbH.

Preparation of ordered mesoporous and macroporous thermoplastic polyurethane surfaces for potential medical applications.

PubMed

Chennell, Philip; Feschet-Chassot, Emmanuelle; Sautou, Valérie; Mailhot-Jensen, Bénédicte

2018-05-01

Thermoplastic polyurethanes are widely used in medical devices. In order to limit some of their shortfalls, like microbial attachment, surfaces modifications can be required. In this work, a two-step replication method was used to create ordered macroporous and mesoporous thermoplastic polyurethane surfaces using anodic aluminum oxide as master template. The intermediate mould materials that were tested were polystyrene and a polyacrylate resin with inorganic filler. All obtained surfaces were characterized by scanning electron microscopy. The initial anodic aluminum oxide surfaces possessed macro or mesopores, function of anodization conditions. The intermediate mould structure correctly replicated the pattern, but the polystyrene surface structures (pillars) were less resistant than the polyacrylate resin ones. The thermoplastic polyurethane pattern possessed macropores or mesopores of about 130 nm or 46 nm diameter and of about 300 nm or 99 nm interpore distances, respectively, in accordance with the initial pattern. Thermoplastic polyurethanes pore depth was however less than initial anodic aluminum oxide pore depth, linked to an incomplete replication during intermediate mould preparation (60 to 90% depth replication). The correct replication of the original pattern confirms that this novel fabrication method is a promising route for surface patterning of thermoplastic polyurethanes that could be used for medical applications.

Protection of Historical Wood against Microbial Degradation—Selection and Application of Microbiocides

PubMed Central

Koziróg, Anna; Rajkowska, Katarzyna; Otlewska, Anna; Piotrowska, Małgorzata; Kunicka-Styczyńska, Alina; Brycki, Bogumił; Nowicka-Krawczyk, Paulina; Kościelniak, Marta; Gutarowska, Beata

2016-01-01

The aim of this study was to select effective and safe microbiocides for the disinfection and protection of historical wooden surfaces at the former Auschwitz II-Birkenau concentration and extermination camp. We tested seven active compounds against bacteria and moulds, of which didecyldimethylammonium chloride and N-(3-aminopropyl)-N-dodecylpropane-1,3-diamine were effective even at 0.02%–2%. Subsequently, eight microbiocides containing the selected active ingredients were chosen and applied three times on the surface of wood samples colonized by bacteria and moulds. ABM-1 and ABM-2—6% solution; Rocima 101—8%; Preventol R 80—12%; Acticide 706 LV—15% and Boramon—30% were the most effective disinfectants. Under laboratory conditions, ABM-1, Boramon and Rocima 101 ensured antimicrobial protection of new wood samples for six months. In situ, 30% Boramon and 8% Rocima 101 applied by spraying effectively protected the historical wood from bacterial and mould growth for 12 and 3 months, respectively. Colour and luminance of the new wood were not altered after exposure to the biocides. Boramon and Rocima 101, applied by the spraying method, caused no significant change in the colour of the historical wood. Results from this study were used to develop a procedure for the protection of wood in historical buildings against biodeterioration. PMID:27556450

Opportunistic toenail onychomycosis. The fungal colonization of an available nail unit space by non-dermatophytes is produced by the trauma of the closed shoe by an asymmetric gait or other trauma. A plausible theory.

PubMed

Zaias, N; Escovar, S X; Rebell, G

2014-08-01

Opportunistic onychomycosis is defined, when a non-dermatophyte mould is cultured from an abnormal nail unit in the absence of a dermatophyte. The presumption is that the mould has caused the abnormal clinical appearance of the nail unit, yet there are no data available to substantiate this claim. Reports have only identified the mould being recovered from the nail unit niche. A review of the published dermatologic literature describing toenail opportunistic onychomycosis by non-dermatophyte fungi has shown toenails with onycholysis, nail bed (NB) keratosis and nail plate surface abnormalities. The appearance of these clinical changes is indistinguishable from the diagnosis of the Asymmetric Gait Nail Unit Signs (AGNUS). AGNUS is produced by the friction of the closed shoe in patients with an asymmetric gait, resulting primarily from the ubiquitous uneven flat feet. Most commonly, species of Acremonium (Cephalosporium), Aspergillus, Fusarium, Scopulariopsis and rarely species of many different fungi genera are capable of surviving and reproducing in a keratinous environment and change the clinical appearance of the involved nail unit. AGNUS toenails predispose to the colonization by the non-dermatophyte opportunistic fungi but not by dermatophyte fungi. © 2014 European Academy of Dermatology and Venereology.

Functionality of selected strains of moulds and yeasts from Vietnamese rice wine starters.

PubMed

Dung, N T P; Rombouts, F M; Nout, M J R

2006-06-01

The role of starch-degrading mycelial fungi, and the alcohol production and ethanol tolerance of the yeasts isolated from selected Vietnamese traditional rice wine starters were examined, and optimum conditions for these essential steps in rice wine fermentation were determined. Of pure isolates from Vietnamese rice wine starters, mould strains identified as Amylomyces rouxii, Amylomyces aff. rouxii, Rhizopus oligosporus and Rhizopus oryzae, were superior in starch degradation, glucose production and amyloglucosidase activity during the saccharification of purple glutinous rice. A. rouxii was able to produce up to 25%w/w glucose with an amyloglucosidase activity up to 0.6 Ug(-1) of fermented moulded mass. Five yeast isolates identified as Saccharomyces cerevisiae were selected for their superior alcohol productivity. They were able to deplete a relatively high initial percentage of glucose (20% w/v), forming 8.8% w/v ethanol. The ethanol tolerance of S. cerevisiae in challenge tests was 9-10% w/v, and 13.4% w/v as measured in fed-batch fermentations. Optimum conditions for the saccharification were: incubation for 2 d at 34 degrees C, of steamed rice inoculated with 5 log cfu g(-1); for the alcoholic fermentation 4 d at 28.3 degrees C, of saccharified rice liquid inoculated with 5.5 log cfu mL(-1).

[Effectiveness of aqueous extracts of aromatic and medicinal plants against tomato grey mould in Morocco].

PubMed

Kasmi, Manal; Aourach, Mohammed; El Boukari, Mohammed; Barrijal, Said; Essalmani, Haiat

2017-08-01

Grey mould is a major disease threatening the Moroccan tomato; this disease is often controlled by fungicides. However, the latter are a real danger to human health and environment. Thus, this study is part of the research of harmless alternatives such extracts of aromatic and medicinal plants (Lavandula officinalis, Thymus vulgaris, Cymbopogon citratus, and Melissa officinalis). In this study, the extracts of four medicinal and aromatic plants were tested for their antifungal potency in vitro and in vivo in order to select the most effective. The results show that, in vitro, the Lavandula officinalis, Thymus vulgaris and Cymbopogon citratus aqueous extracts all possess significant antifungal activity, whereas Melissa officinalis shows the least effective. Also in vivo only the aqueous extract of Cymbopogon citratus proves most effective against B. cinerea on tomato fruit. The test of the plants confirms that aqueous extracts of Cymbopogon citratus and Thymus vulgaris are most effective, while the aqueous extracts of Melissa officinalis and Lavandula officinalis always seem to be the least effective. Therefore, the aqueous extracts of Cymbopogon citratus and Thymus vulgaris are the most envisaged for the biological control of grey mould. Copyright © 2017 Académie des sciences. Published by Elsevier Masson SAS. All rights reserved.

Sources of household air pollution: The association with lung function and respiratory symptoms in middle-aged adult.

PubMed

Devien, Laurent; Giovannelli, Jonathan; Cuny, Damien; Matran, Régis; Amouyel, Philippe; Hulo, Sébastien; Edmé, Jean Louis; Dauchet, Luc

2018-07-01

The objective of the present study was to investigate the relationship between sources of household air pollution, respiratory symptoms and lung function. 3039 adults aged from 40 to 65 participated in the 2011-2013 ELISABET cross-sectional survey in northern France. Lung function was measured using spirometry. During a structured interview, respiratory symptoms, household fuels, exposure to moulds, and use of ventilation were recorded on a questionnaire. The self-reported presence of mould in at least two rooms (not including the bathroom and the kitchen) was associated with a 2.5% lower predicted forced expiratory volume in 1 s (95% confidence interval, -4.7 to -0.29; p-trend <0.05) and a higher risk of wheezing (p-trend < 0.001). Visible condensation was associated with wheezing (p < .05) and chronic cough (p < .05). There were no significant associations with the type of household fuel or inadequate ventilation/aeration. Similar results were found when the analyses were restricted to participants without known respiratory disease. Our results suggest that the presence of mould (known to be associated with more severe asthma symptoms) could also have an impact on respiratory symptoms and lung function in the general population and in populations without known respiratory disease. Copyright © 2018 Elsevier Inc. All rights reserved.

Combination of Pichia membranifaciens and ammonium molybdate for controlling blue mould caused by Penicillium expansum in peach fruit.

PubMed

Cao, Shifeng; Yuan, Yongjun; Hu, Zhichao; Zheng, Yonghua

2010-07-15

The potential enhancement of Pichia membranifaciens by ammonium molybdate (NH(4)Mo) to control blue mould caused by Penicillium expansum on peach fruit was investigated. Combining P. membranifaciens at 1x10(8) cell/ml with 1 mM NH(4)Mo provided a more effective control of blue mould rot than applying the yeast or NH(4)Mo alone. Addition of 1 mM NH(4)Mo significantly increased the growth of P. membranifaciens in peach wounds, but did not affect the population in nutrient yeast dextrose broth medium. The in vitro experiment showed that the combined treatment inhibited spore germination and germ tube elongation of P. expansum in comparison with the treatment of P. membranifaciens or NH(4)Mo alone. Moreover, P. membranifaciens, NH(4)Mo, and the combination of them did not impair the quality parameters including fruit firmness and content of total soluble solids, titratable acidity and vitamin C of peach fruit after 6 days of storage at 20 degrees C. These results suggested that the use of NH(4)Mo is a useful approach to improve the efficacy of P. membranifaciens for postharvest disease control in peach fruit. 2010 Published by Elsevier B.V. All rights reserved.

Poor housing conditions in association with child health in a disadvantaged immigrant population: a cross-sectional study in Rosengård, Malmö, Sweden

PubMed Central

Richter, Jens C; Taj, Tahir; Al-nahar, Lina; Jakobsson, Kristina

2016-01-01

Objectives To describe the home environment in terms of housing conditions and their association with child health in a disadvantaged immigrant population. Design A cross-sectional observational study. Setting Enrolment took place during 2010–2011 in Rosengård, Malmö, Sweden. Participants Children aged 0–13 years in 2 study neighbourhoods were recruited from local health records and from schools. 359 children participated, with a participation rate of 40%. Data on health, lifestyle and apartment characteristics from questionnaire-led interviews with the mothers of the children were obtained together with data from home inspections carried out by trained health communicators. Outcome measures Logistic regression analysis was used to estimate ORs for various health outcomes, adjusted for demographic information and lifestyle factors. Results The housing conditions were very poor, especially in one of the study neighbourhoods where 67% of the apartments had been sanitised of cockroaches, 27% were infested with cockroaches and 40% had a visible mould. The association between housing conditions and health was mostly inconclusive, but there were statistically significant associations between current asthma and dampness (OR=4.1, 95% CI 1.7 to 9.9), between asthma medication and dampness (OR=2.8, 95% CI 1.2 to 6.4), and between mould and headache (OR=4.2, 95% CI 1.2 to 14.8). The presence of cockroaches was associated with emergency care visits, with colds, with headache and with difficulty falling asleep, and worse general health was associated with mould and presence of cockroaches. Conclusions The associations between dampness and asthma, and the association between mould and headache, are in line with current knowledge. The presence of cockroaches seemed to be associated with various outcomes, including those related to mental well-being, which is less described in the literature. The results of the present study are hypothesis generating and provide strong incentives for future studies in this study population. PMID:26739718

Fungal endocarditis in paediatrics: a review of 192 cases (1971-2016).

PubMed

Ganesan, Vithiya; Ponnusamy, Shunmuga Sundaram; Sundaramurthy, Raja

2017-10-01

The aims of this article were to review the published literature on fungal endocarditis in children and to discuss the aetiology and diagnosis, with emphasis on non-invasive methods and various treatment regimes. We systematically reviewed published cases and case series of fungal endocarditis in children. We searched the literature, including PubMed and individual references for publications of original articles, single cases, or case series of paediatric fungal endocarditis, with the following keywords: "fungal endocarditis", "neonates", "infants", "child", and "cardiac vegetation". There have been 192 documented cases of fungal endocarditis in paediatrics. The highest number of cases was reported in infants (93/192, 48%) including 60 in neonates. Of the neonatal cases, 57 were premature with a median gestational age of 27 weeks and median birth weight of 860 g. Overall, 120 yeast - fungus that grows as a single cell - infections and 43 mould - fungus that grows in multicellular filaments, hyphae - infections were reported. With increasing age, there was an increased infection rate with moulds. All the yeast infections were detected by blood culture. In cases with mould infection, diagnosis was mainly established by culture or histology of emboli or infected valves after invasive surgical procedures. There have been a few recent cases of successful early diagnosis by non-invasive methods such as blood polymerase chain reaction (PCR) for moulds. The overall mortality for paediatric fungal endocarditis was 56.25%. The most important cause of death was cardiac complications due to heart failure. Among the various treatment regimens used, none of them was significantly associated with better outcome. Non-invasive methods such as PCR tests can be used to improve the chances of detecting and identifying the aetiological agent in a timely manner. Delays in the diagnosis of these infections may result in high mortality and morbidity. No significant difference was noted between combined surgical and medical therapy over exclusively combined medical therapy.

Microinjection moulding of polymeric composites with functionalized carbon nanotubes =

NASA Astrophysics Data System (ADS)

Ferreira, Tania Sofia Araujo Figueiras

Microinjection moulding of polymeric composites with functionalized carbon nanotubes The unique electronic, mechanical, and structural properties of carbon nanotubes (CNT) make them suitable for applications in the fields of electronics, sensors, medical devices, aerospace and automotive industries. The preparation of CNT/polymer nanocomposites presents particular interest among the various possible applications. However, the long entangled nanotubes form agglomerates that poses serious obstacles to further development of nanocomposites with the target properties. One of the approaches to overcome the CNT chemical inertness, enhance the compatibility with the matrix and improve homogeneous dispersion through the matrix is through its covalent functionalization. This is expected to improve the CNT interface with the polymer matrix, thus improving the mechanical properties of the nanocomposites at very low content. One of the purposes of this thesis was to implement the covalent modification of the CNT surface using a simple functionalization method, to increase the CNT surface reactivity and possibly help their dispersion into the polyamide matrix without inducing structural damage on the CNT. The functionalization of CNT was carried out through the 1,3-dipolar cycloaddition reaction of azomethine ylides using a solvent-free reaction route. CNT were successful functionalized with pyrrolidine groups through a simple and fast procedure that was scaled up, and may be compatible with current industrial processes. Another objective was to disperse the CNT in polyamide 6 (PA6) using melt mixing, and to produce PA6/CNT nanocomposites by microinjection molding (plM). Finally, the morphological and physical properties of the mouldings produced were evaluated. The plM process is becoming of greater importance for the manufacturing of polymeric micro- components considering its low cost and short cycle times, useful for mass production. The as-received and functionalized CNT were dispersed in PA6 at various contents (1, 1.5, 3 and 4.5 w.%) by twin-screw extrusion and then processed by pllVl. The same procedure was carried out for PA6 without CNT. To study the influence of the specific thermo-mechanical conditions generated during pllVl, the morphology and structure of PA6 and PA6/CNT samples produced by melt extrusion and plM were compared. The specimens of PA6 and PA6/CNT nanocomposites were analyzed by polarized light microscopy, differential scanning calorimetry, and wide-angle X-ray diffraction. The effect of the processing method upon the development of crystallinity in PA6 and PA6/CNT samples was studied. The contribution of the two crystalline phases, oi and y, on the PA6 with and without CNT was measured. The degree of crystallinity of the plM PA6 sample was lower compared to the extruded material, and was not affected by the CNT content. The plM samples of PA6 presented a considerable molecular orientation at the skin region that decreased towards the sample core, with larger contribution of y-phase compared to extruded samples. The orientation exhibited by plM parts of PA6, mainly at the skin region, is not detectable after CNT addition. The dispersion of the CNT agglomerates was quantified in all PA6/CNT samples using optical microscopy and image analysis. The effect of functionalization on the PA6/CNT interface, the nanocomposite morphology and the mechanical and electrical properties were studied. It was observed that the microinjected composites with functionalized CNT presented improved dispersion, with smaller CNT agglomerate area ratio compared to the composites with pure nanotubes. The functionalized nanotubes showed better adhesion to PA6 compared to pure nanotubes, as observed by scanning electron microscopy. The incorporation of CNT considerably improved the mechanical properties. The effect of high shear rate of the polymer melt on carbon nanotube alignment during plM was assessed by comparing the electrical resistivity of the composite after extrusion and after pllVl, through the thickness and along the flow direction. The experiments showed that the moulding geometry design and processing conditions significantly affected electrical resistivity. This thesis provides an insight into the joint effect of CNT chemical functionalization and the specific conditions of plM on PA6 morphology and on CNT dispersion, and its influence on the electrical, mechanical and thermal properties of the resulting composites.

Biaxial deformation behaviour of poly-ether-ether-ketone

NASA Astrophysics Data System (ADS)

Turner, Josh; Menary, Gary; Martin, Peter

2018-05-01

The biaxial tensile properties of thin poly-ether-ether-ketone (PEEK) films are presented. Investigation into the biaxial mechanical behaviour of PEEK films will provide a preliminary insight into the anticipated stress/strain response, and potential suitability, to the possible fabrication of thin walled parts through stretch blow moulding and thermoforming processes - with the multi-axial state of strain imposed onto the heated thermoplastic sheet representative of the expected strain history experienced during these material forming processes. Following identification of the prospective forming temperature window, the biaxial mechanical behaviour of the material is characterized under differing modes of deformation, at a nominal strain rate of 1 s-1. The temperature dependence is outlined within - with an appreciable increase in flow behaviour correlated with specimen temperature exceeding its glass transition temperature (Tg).

Classification, processing and application of hydrogels: A review.

PubMed

Ullah, Faheem; Othman, Muhammad Bisyrul Hafi; Javed, Fatima; Ahmad, Zulkifli; Md Akil, Hazizan

2015-12-01

This article aims to review the literature concerning the choice of selectivity for hydrogels based on classification, application and processing. Super porous hydrogels (SPHs) and superabsorbent polymers (SAPs) represent an innovative category of recent generation highlighted as an ideal mould system for the study of solution-dependent phenomena. Hydrogels, also termed as smart and/or hungry networks, are currently subject of considerable scientific research due to their potential in hi-tech applications in the biomedical, pharmaceutical, biotechnology, bioseparation, biosensor, agriculture, oil recovery and cosmetics fields. Smart hydrogels display a significant physiochemical change in response to small changes in the surroundings. However, such changes are reversible; therefore, the hydrogels are capable of returning to its initial state after a reaction as soon as the trigger is removed. Copyright © 2015 Elsevier B.V. All rights reserved.

Vacuum infusion method for woven carbon/Kevlar reinforced hybrid composite

NASA Astrophysics Data System (ADS)

Hashim, N.; Majid, D. L.; Uda, N.; Zahari, R.; Yidris, N.

2017-12-01

The vacuum assisted resin transfer moulding (VaRTM) or Vacuum Infusion (VI) is one of the fabrication methods used for composite materials. Compared to other methods, this process costs lower than using prepregs because it does not need to use the autoclave to cure. Moreover, composites fabricated using this VI method exhibit superior mechanical properties than those made through hand layup process. In this study, the VI method is used in fabricating woven carbon/Kevlar fibre cloth with epoxy matrix. This paper reports the detailed methods on fabricating the hybrid composite using VI process and several precautions that need to be taken to avoid any damage to the properties of the composite material. The result highlights that the successfully fabricated composite has approximately 60% of fibres weight fraction. Since the composites produced by the VI process have a higher fibre percentage, this process should be considered for composites used in applications that are susceptible to the conditions where the fibres need to be the dominant element such as in tension loading.

Considerations on the construction of a Powder Bed Fusion platform for Additive Manufacturing

NASA Astrophysics Data System (ADS)

Andersen, Sebastian Aagaard; Nielsen, Karl-Emil; Pedersen, David Bue; Nielsen, Jakob Skov

As the demand for moulds and other tools becomes increasingly specific and complex, an additive manufacturing approach to production is making its way to the industry through laser based consolidation of metal powder particles by a method known as powder bed fusion. This paper concerns a variety of design choices facilitating the development of an experimental powder bed fusion machine tool, capable of manufacturing metal parts with strength matching that of conventional manufactured parts and a complexity surpassing that of subtractive processes. To understand the different mechanisms acting within such an experimental machine tool, a fully open and customizable rig is constructed. Emphasizing modularity in the rig, allows alternation of lasers, scanner systems, optical elements, powder deposition, layer height, temperature, atmosphere, and powder type. Through a custom-made software platform, control of the process is achieved, which extends into a graphical user interface, easing adjustment of process parameters and the job file generation.

Preliminary Study on GF/Carbon/Epoxy Composite Permeability in Designing Close Compartment Processing

NASA Astrophysics Data System (ADS)

Ya’acob, A. M.; Razali, D. A.; Anwar, U. A.; Radhi, A. H.; Ishak, A. A.; Minhat, M.; Aris, K. D. Mohd; Johari, M. K.; Casey, T.

2018-05-01

This project involves discovering how the permeability effect inside a close compartment in processing. After the appropriate pressure range was found, the close compartment was designed by studying the relationship between pressure output and the flow rate. A variety of pressure ranges have been used in this test to determine the effective pressure range that can be applied to the manufacturing process. Based on the results, the suitable pressure ranges were found between 55 psi to 75 psi. These pressures have been chosen based on the area covered on the product surfaces and time taken to penetrate the proposed area. The relationship between pressure and flow rate have been found to be directly proportional until 75 psi only. In conclusion, 70 psi for the proposed design of close compartment mould is suitable to be used to fulfill the required area of 120 mm square within 90 seconds.

Processing and damage recovery of intrinsic self-healing glass fiber reinforced composites

NASA Astrophysics Data System (ADS)

Sordo, Federica; Michaud, Véronique

2016-08-01

Glass fiber reinforced composites with a self-healing, supramolecular hybrid network matrix were produced using a modified vacuum assisted resin infusion moulding process adapted to high temperature processing. The quality and fiber volume fraction (50%) of the obtained materials were assessed through microscopy and matrix burn-off methods. The thermo-mechanical properties were quantified by means of dynamic mechanical analysis, revealing very high damping properties compared to traditional epoxy-based glass fiber reinforced composites. Self-healing properties were assessed by three-point bending tests. A high recovery of the flexural properties, around 72% for the elastic modulus and 65% of the maximum flexural stress, was achieved after a resting period of 24 h at room temperature. Recovery after low velocity impact events was also visually observed. Applications for this intrinsic and autonomic self-healing highly reinforced composite material point towards semi-structural applications where high damping and/or integrity recovery after impact are required.

A hybrid, auto-adaptive and rule-based multi-agent approach using evolutionary algorithms for improved searching

NASA Astrophysics Data System (ADS)

Izquierdo, Joaquín; Montalvo, Idel; Campbell, Enrique; Pérez-García, Rafael

2016-08-01

Selecting the most appropriate heuristic for solving a specific problem is not easy, for many reasons. This article focuses on one of these reasons: traditionally, the solution search process has operated in a given manner regardless of the specific problem being solved, and the process has been the same regardless of the size, complexity and domain of the problem. To cope with this situation, search processes should mould the search into areas of the search space that are meaningful for the problem. This article builds on previous work in the development of a multi-agent paradigm using techniques derived from knowledge discovery (data-mining techniques) on databases of so-far visited solutions. The aim is to improve the search mechanisms, increase computational efficiency and use rules to enrich the formulation of optimization problems, while reducing the search space and catering to realistic problems.

Features of development process displacement of earth’s surface when dredging coal in Eastern Donbas

NASA Astrophysics Data System (ADS)

Posylniy, Yu V.; Versilov, S. O.; Shurygin, D. N.; Kalinchenko, V. M.

2017-10-01

The results of studies of the process of the earth’s surface displacement due to the influence of the adjacent longwalls are presented. It is established that the actual distributions of soil subsidence in the fall and revolt of the reservoir with the same boundary settlement processes differ both from each other and by the distribution of subsidence, recommended by the rules of structures protection. The application of the new boundary criteria - the relative subsidence of 0.03 - allows one to go from two distributions to one distribution, which is also different from the sedimentation distribution of protection rules. The use of a new geometrical element - a virtual point of the mould - allows one to transform the actual distribution of subsidence in the model distribution of rules of constructions protection. When transforming the curves of subsidence, the boundary points vary and, consequently, the boundary corners do.

Valorisation of blueberry waste and use of compression to manufacture sustainable starch films with enhanced properties.

PubMed

Luchese, Cláudia Leites; Uranga, Jone; Spada, Jordana Corralo; Tessaro, Isabel Cristina; de la Caba, Koro

2018-08-01

Blueberry waste from juice processing was valorised to develop starch films by compression moulding. The compression process resulted in hydrophobic films with water contact angles even higher than 100° for the films prepared with the highest blueberry waste content. Additionally, the film solubility was reduced by the incorporation of blueberry waste, regardless of the solution pH. These films also exhibited good barrier properties against UV light due to the aromatic compounds present in the blueberry waste. Furthermore, films showed a homogenous surface, although some pores appeared in the cross-section for the films with the highest blueberry waste content. Results highlighted the use of thermo-mechanical processes such as compression to manufacture sustainable films with enhanced properties through waste valorisation by the techniques actually employed at industrial scale. Copyright © 2018 Elsevier B.V. All rights reserved.

Study on preparation and mechanical performance of TPU/nonwoven composites

NASA Astrophysics Data System (ADS)

Sun, X. C.; Xi, B. J.

2016-07-01

In order to study the influence of resin content and layer sequence parameters on the mechanical properties of TPU/non-woven composite materials synthesized by moulding pressing technology. The effects of the resin content and layer sequence on composites were discussed. Through experiments and theoretical analysis, it was revealed how resin content, layer sequence impact on mechanical properties of composite. The mechanics properties of TPU/non-woven composite materials are improved. The process is pressure 0.5 MPa, temperature 110 °C and time 120s min. The melting of the TPU infiltrated into the fabric and filled the space between the fibers.

[Evaluation of the quality of poultry meat and its processing for vacuum packaging].

PubMed

Swiderski, F; Russel, S; Waszkiewicz-Robak, B; Cholewińska, E

1997-01-01

The aim of study was to evaluate the quality of poultry meat, roasted and smoked chicken and poultry pie packing under low and high vacuum. All investigated products were stored at +4 degrees C and evaluated by microbiological analysis. It was showed that packing under low and high vacuum inhibited development of aerobic microorganisms, proteolytic bacteria, yeasts and moulds. Vacuum-packaged storage of poultry meat and its products stimulated activity of anaerobic, nonsporeforming bacteria. The fast spoilage of fresh poultry meat was observed both under vacuum and conventional storage. The microbiology quality of poultry products depended on technology of production and microbiological quality of raw material.

Toxic effects of mycotoxins in humans.

PubMed Central

Peraica, M.; Radić, B.; Lucić, A.; Pavlović, M.

1999-01-01

Mycotoxicoses are diseases caused by mycotoxins, i.e. secondary metabolites of moulds. Although they occur more frequently in areas with a hot and humid climate, favourable for the growth of moulds, they can also be found in temperate zones. Exposure to mycotoxins is mostly by ingestion, but also occurs by the dermal and inhalation routes. Mycotoxicoses often remain unrecognized by medical professionals, except when large numbers of people are involved. The present article reviews outbreaks of mycotoxicoses where the mycotoxic etiology of the disease is supported by mycotoxin analysis or identification of mycotoxin-producing fungi. Epidemiological, clinical and histological findings (when available) in outbreaks of mycotoxicoses resulting from exposure to aflatoxins, ergot, trichothecenes, ochratoxins, 3-nitropropionic acid, zearalenone and fumonisins are discussed. PMID:10534900

Laser ablated micropillar energy directors for ultrasonic welding of microfluidic systems

NASA Astrophysics Data System (ADS)

Esben Poulsen, Carl; Kistrup, Kasper; Korsgaard Andersen, Nis; Taboryski, Rafael; Fougt Hansen, Mikkel; Wolff, Anders

2016-06-01

We present a new type of energy director (ED) for ultrasonic welding of microfluidic systems. These micropillar EDs are based on the replication of cone like protrusion structures introduced using a pico-second laser and may therefore be added to any mould surface accessible to a pico-second laser beam. The technology is demonstrated on an injection moulded microfluidic device featuring high-aspect ratio (h  ×  w  =  2000 μm  ×  550 μm) and free-standing channel walls, where bonding is achieved with no detectable channel deformation. The bonding strength is similar to conventional EDs and the fabricated system can withstand pressures of over 9.5 bar.

High frequency of pathogenic Aspergillus species among nonsporulating moulds from respiratory tract samples.

PubMed

Dufresne, Philippe J; Moonjely, Soumya S; Ozaki, Koyomi; Tremblay, Cécile; Laverdière, Michel; Dufresne, Simon F

2017-02-01

Nonsporulating moulds (NSM) represent an identification challenge for clinical laboratories. Data on the prevalence of pathogenic species among NSM are lacking. We prospectively investigated consecutive thermotolerant (36°C) clinical NSM isolates from respiratory tract samples. A total of 123 isolates were identified by DNA sequencing and phenotypically characterized. Of those, 13 (11%) were pathogenic species (Aspergillus fumigatus, n = 10; A. flavus, n = 1; A. hiratsukae, n = 1; Schizophyllum commune, n = 1). Presumptive identification of Aspergillus species among NSM can be achieved by simple phenotypic testing. © The Author 2016. Published by Oxford University Press on behalf of The International Society for Human and Animal Mycology. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

An improved model for teaching use of electronic apex locators.

PubMed

Tchorz, J P; Hellwig, E; Altenburger, M J

2012-04-01

To develop a simple, practical and inexpensive model, which enables the use of electronic apex locators (EALs) during pre-clinical and continuing education. Extracted teeth were placed in a mould and embedded in acrylic resin. The resin was applied in two consecutive steps to form a cavity around the root apices. A closable plastic tube serves as a valve, and a steel wire connects to the EAL. With its semi-closed reservoir for conductive fluids surrounding the root apices, the new model enables working length measurements of root canals using EALs. The model simulates the clinical situation for endodontic teaching purposes, as it allows working length determination of root canals as recommended. The measuring results of the EAL can be verified by radiography. At the same time, the roots are not directly visible and accessible to the user, allowing a precise evaluation and grading of the treatment. © 2011 International Endodontic Journal.

Division Viii: Galaxies and the Universe

NASA Astrophysics Data System (ADS)

Sadler, Elaine M.; Combes, Françoise; Okamura, Sadanori; Davies, Roger L.; Gallagher, John S.; Padmanabhan, Thanu; Schmidt, Brian P.

2012-04-01

The fields of extragalactic research and cosmology have continued to progress rapidly over the past three years, as detailed in the reports of the Commission Presidents, and we are pleased to acknowledge the award of the 2011 Nobel Prize in Physics to Saul Perlmutter, Brian P. Schmidt and Adam G. Riess for ``the discovery of the accelerating expansion of the Universe through observations of distant supernovae''. The Gruber Cosmology Prize was awarded in 2009 to Wendy L. Freedman, Robert C. Kennicutt and Jeremy Mould for their leadership of the Hubble Space Telescope Key Project on the Extragalactic Distance Scale, in 2010 to Charles Steidel for the identification and study of galaxies in the very distant universe, and in 2011 to Marc Davis, George Efstathiou, Carlos Frenk and Simon D.M. White for pioneering the use of numerical simulations as a tool to model and interpret the large-scale distribution of galaxies and dark matter.

TOPICAL REVIEW: Monitoring of polymer melt processing

NASA Astrophysics Data System (ADS)

Alig, Ingo; Steinhoff, Bernd; Lellinger, Dirk

2010-06-01

The paper reviews the state-of-the-art of in-line and on-line monitoring during polymer melt processing by compounding, extrusion and injection moulding. Different spectroscopic and scattering techniques as well as conductivity and viscosity measurements are reviewed and compared concerning their potential for different process applications. In addition to information on chemical composition and state of the process, the in situ detection of morphology, which is of specific interest for multiphase polymer systems such as polymer composites and polymer blends, is described in detail. For these systems, the product properties strongly depend on the phase or filler morphology created during processing. Examples for optical (UV/vis, NIR) and ultrasonic attenuation spectra recorded during extrusion are given, which were found to be sensitive to the chemical composition as well as to size and degree of dispersion of micro or nanofillers in the polymer matrix. By small-angle light scattering experiments, process-induced structures were detected in blends of incompatible polymers during compounding. Using conductivity measurements during extrusion, the influence of processing conditions on the electrical conductivity of polymer melts with conductive fillers (carbon black or carbon nanotubes) was monitored.

Innovative Chemical Process for Recycling Thermosets Cured with Recyclamines® by Converting Bio-Epoxy Composites in Reusable Thermoplastic—An LCA Study

PubMed Central

Banatao, Diosdado R.; Pastine, Stefan J.

2018-01-01

An innovative recycling process for thermoset polymer composites developed by Connora Technologies (Hayward, CA, USA) was studied. The process efficacy has already been tested, and it is currently working at the plant level. The main aspect investigated in the present paper was the environmental impact by means of the Life Cycle Assessment (LCA) method. Because of the need to recycle and recover materials at their end of life, the Connora process creates a great innovation in the market of epoxy composites, as they are notoriously not recyclable. Connora Technologies developed a relatively gentle chemical recycling process that induces the conversion of thermosets into thermoplastics. The LCA demonstrated that low environmental burdens are associated with the process itself and, furthermore, impacts are avoided due to the recovery of the epoxy-composite constituents (fibres and matrix). A carbon fibre (CF) epoxy-composite panel was produced through Vacuum Resin Transfer Moulding (VRTM) and afterwards treated using the Connora recycling process. The LCA results of both the production and the recycling phases are reported. PMID:29495571

Occupational asthma in greenhouse workers.

PubMed

Monsó, Eduard

2004-03-01

A prevalence of asthma over 5% has been reported in flower farmers,and work inside greenhouses has emerged as an additional risk factor. Workplace determinants behind this high prevalence has been examined, and a prevalence of sensitization to workplace allergens over 30% has been reported being pollens, moulds, and Tetranychus urticae allergens the main sensitizers. Bronchial challenge tests in the workplace have demonstrated occupational asthma in more than 20% of the sensitized greenhouse growers. Air contamination inside greenhouses is mainly related to moulds, and is facilitated by the high indoor temperature and humidity. Cladosporium, Penicillium, Aspergillus, and Alternaria and a wide range of flower pollens are able to sensitize the greenhouse worker and cause occupational asthma. Tetranychus urticae have allergens shared with other mites, but the low prevalence of cross-sensitization between them confirm that Tetranychus urticae contains species-specific allergens that may cause respiratory symptoms. Additionally, working inside greenhouses has been related to an increase in the prevalence of chronic bronchitis in nonsmokers. The cultivation of greenhouse crops may cause occupational asthma through sensitization to workplace pollens, moulds, and Tetranychus urticae allergens. In greenhouse flower growers, skin testing identifies sensitization to these allergens in one third of the growers, and more than one fifth of the sensitized workers will develop occupational asthma. Greenhouse work has also been related to chronic bronchitis in nonsmokers, suggesting a causal effect of greenhouse air contaminants on this disease as well.

A potent feed preservative candidate produced by Calcarisporium sp., an endophyte residing in stargrass (Cynodon dactylon).

PubMed

Ji, L L; Song, Y C; Tan, R X

2004-01-01

The cultures of an endophytic fungus Calcarisporium sp. were screened for inhibitors on the growth of feed-associated moulds and on the aflatoxin biosynthesis to find a safe and effective feed preservative. Eight test fungi were isolated from the spoiled poultry feed. The endophytic fungus Calcarisporium sp. was separated from the Chinese coastal grass Cynodon dactylon. The antifungal action concerning the endophytic culture extract (ECE) was performed with propionic acid (PPA) as the corresponding reference. The ECE had a similar antifungal efficacy to PPA in a concentration-dependent manner. The susceptibility order of the ECE to the test fungi was found to be Fusarium sp. > Aspergillus spp. > Penicillium spp. Furthermore, the application of the ECE in pelleted-layer duck feed as a preservative was carried out at a humidity of 10, 15 and 20%. It has been discerned that mould growth and aflatoxin biosynthesis could be co-inhibited almost completely by ECE at concentrations higher than 1.0% (w/w). The LD50 of the ECE on mice was shown to be higher than 28 g kg-1. The ECE can be selected as an inhibitor to preserve poultry feed on inhibiting the growth of mould and aflatoxin biosynthesis during feed storage. The ECE may be an effective and biosafe antifungal ingredient for poultry feed and holds a potential market prospect in feed industry.

Straightforward and precise approach to replicate complex hierarchical structures from plant surfaces onto soft matter polymer

PubMed Central

Speck, Thomas; Bohn, Holger F.

2018-01-01

The surfaces of plant leaves are rarely smooth and often possess a species-specific micro- and/or nano-structuring. These structures usually influence the surface functionality of the leaves such as wettability, optical properties, friction and adhesion in insect–plant interactions. This work presents a simple, convenient, inexpensive and precise two-step micro-replication technique to transfer surface microstructures of plant leaves onto highly transparent soft polymer material. Leaves of three different plants with variable size (0.5–100 µm), shape and complexity (hierarchical levels) of their surface microstructures were selected as model bio-templates. A thermoset epoxy resin was used at ambient conditions to produce negative moulds directly from fresh plant leaves. An alkaline chemical treatment was established to remove the entirety of the leaf material from the cured negative epoxy mould when necessary, i.e. for highly complex hierarchical structures. Obtained moulds were filled up afterwards with low viscosity silicone elastomer (PDMS) to obtain positive surface replicas. Comparative scanning electron microscopy investigations (original plant leaves and replicated polymeric surfaces) reveal the high precision and versatility of this replication technique. This technique has promising future application for the development of bioinspired functional surfaces. Additionally, the fabricated polymer replicas provide a model to systematically investigate the structural key points of surface functionalities. PMID:29765666

Clothing increases the risk of indirect ballistic fractures

PubMed Central

2013-01-01

Background Current literature has shown the mechanism of how indirect fractures occur but has not determined what factors increase the risks of such fractures. The objective of this study is thus to determine the effect of clothing and soft tissue thickness on the risk of indirect fracture formation. Methods Twenty-five fresh red deer femora embedded in ballistic gelatine were shot with varying distances off their medial cortex with a 5.56 × 45 mm North Atlantic Treaty Organization (NATO) bullet while being filmed with a slow-motion video. We compared the effect of two different gelatine depths and the effect of denim cloth laid onto the impact surface of the moulds. Results Bullet passage in thinner moulds failed to cause fracture because the bullet exited the mould before a large expanding temporary cavity was produced. Clothing dramatically altered the size and depth of the expanding cavity, as well as increased lateral pressures, resulting in more severe fractures with greater bullet distances from the bone that can cause fracture. Conclusions Clothing increases the risk of indirect fracture and results in larger, more superficial temporary cavities, with greater lateral pressures than are seen in unclothed specimens, resulting in more comminuted fractures. Greater tissue depth affords the 5.56 × 45 mm NATO a chance to yaw and thus develop an enlarging temporary cavity that is sufficient to cause fracture. PMID:24267379

Evaluation of the color durability of acrylic resin veneer materials after immersion in common beverages at different time intervals: A spectrophotometric study.

PubMed

Kohli, Shivani; Bhatia, Shekhar

2015-01-01

Proper function, esthetics, and cost are the prime factors to be considered while selecting bridge veneering materials. The purpose of the study is to evaluate color durability of acrylic veneer materials after immersion in common beverages at different time intervals. Spectrophotometer was used for taking color measurements based on the transmission of light through the specimens made of the selected materials which were Tooth moulding powder (DPI) and Acrylux (Ruthinium). Thirty specimens of standardized dimensions were prepared from each material. The specimens were divided into three groups of 10 each. One group of each material was immersed in tea (TajMahal) and another group of each material in cola (Pepsi) as the staining solutions. The remaining group of 10 from each material served as control and was stored in distilled water. Color measurements were obtained pre-immersion, and after 1, 15, and 30 days of immersion. Tooth moulding powder displayed better color durability than Acrylux over the 1 month immersion period in both staining solutions. Tea resulted in more discoloration compared to cola (Pepsi). The difference in the color durability of Acrylux and Tooth moulding powder may be attributed to the differences in the composition of tested resin veneering materials, i.e. their polar properties, which contribute to the absorption of staining solution, and the different brands and the strengths of the solutions.

Household reporting of childhood respiratory health and air pollution in rural Alaska Native communities.

PubMed

Ware, Desirae N; Lewis, Johnnye; Hopkins, Scarlett; Boyer, Bert; Montrose, Luke; Noonan, Curtis W; Semmens, Erin O; Ward, Tony J

2014-01-01

Air pollution is an important contributor to respiratory disease in children. To examine associations between household reporting of childhood respiratory conditions and household characteristics related to air pollution in Alaska Native communities. In-home surveys were administered in 2 rural regions of Alaska. The 12-month prevalence of respiratory conditions was summarized by region and age. Odds ratios (ORs) were calculated to describe associations between respiratory health and household and air quality characteristics. Household-reported respiratory health data were collected for 561 children in 328 households. In 1 region, 33.6% of children aged <5 years had a recent history of pneumonia and/or bronchitis. Children with these conditions were 2 times more likely to live in a wood-heated home, but these findings were imprecise. Resident concern with mould was associated with elevated prevalence of respiratory infections in children (ORs 1.6-2.5), while reported wheezing was associated with 1 or more smokers living in the household. Reported asthma in 1 region (7.6%) was lower than national prevalence estimates. Findings suggest that there may be preventable exposures, including wood smoke and mould that affect childhood respiratory disease in these rural areas. Additional research is needed to quantify particulate matter 2.5 microns in aerodynamic diameter or less and mould exposures in these communities, and to objectively evaluate childhood respiratory health.

Isavuconazole treatment for rare fungal diseases and for invasive aspergillosis in patients with renal impairment: Challenges and lessons of the VITAL trial.

PubMed

Perfect, John R; Cornely, Oliver A; Heep, Markus; Ostrosky-Zeichner, Luis; Mullane, Kathleen M; Maher, Rochelle; Croos-Dabrera, Rodney; Lademacher, Christopher; Engelhardt, Marc; Chen, Caroline; Marty, Francisco M

2018-03-23

Invasive fungal disease (IFD) confers a substantial risk for morbidity and mortality to immunocompromised patients. Invasive aspergillosis (IA) is the most common IFD caused by moulds but the prevalence of other rare mould diseases, such as mucormycosis, hyalohyphomycosis and phaeohyphomycosis, may be increasing. Treatments are available for IA, but evidence to support efficacy and safety of antifungal agents for rare IFDs, or for IFDs in special patient populations, is limited or lacking. The VITAL trial was conducted to assess the efficacy and safety of isavuconazole for the treatment of patients with IA and renal impairment, or with IFDs caused by rare moulds, yeasts or dimorphic fungi. These patients stand to benefit most from a new treatment option but are unlikely to be included in a randomised, controlled trial. In this article, we review the challenges faced in the design and conduct of the VITAL trial. We also review the findings of VITAL, which included evidence of the efficacy and safety of isavuconazole. Finally, we consider the importance of trials such as VITAL to inform therapeutic decision making for clinicians faced with the challenge of treating patients with rare IFDs and as one paradigm of how to determine efficacy and safety of new drugs for rare and resistant infections without a suitable comparator. © 2018 The Authors. Mycoses Published by Blackwell Verlag GmbH.

A novel feedstuff: ensiling of cowpea (Vigna unguiculata L.) stover and apple (Malus domestica Borkh.) mixtures. Evaluation of the nutritive value, fermentation quality and aerobic stability.

PubMed

Andrade, Ederson; Gonçalves, Alexandre; Mendes-Ferreira, Ana; Silva, Valéria; Pinheiro, Victor; Rodrigues, Miguel; Ferreira, Luis

2017-10-01

Agro-industrial by-products are of low economic value as foods for human consumption but may have potential value as animal feedstuffs. This study evaluated a novel feedstuff, ensiled discarded apple (85%) and cowpea stover (15%) mixtures with two different ensiling periods (45 and 60 days), regarding the nutritive value, fermentation quality and aerobic stability. Generally, no differences (P > 0.05) were observed between ensiling periods for nutritive value and fermentation characteristics. Silages were stable after ensiling, presenting high lactic acid (77.3 g kg -1 dry matter (DM)) and acetic acid (54.7 g kg -1 DM) and low ethanol (15.7 g kg -1 DM) and NH 3 -N (105.6 g kg -1 total N) concentrations. No butyric acid was detected in silages, and they were aerobically stable for up to 216 h. Lactic acid bacteria numbers were high at silo opening (7.14 log colony-forming units (CFU) g -1 ), while Enterobacteriaceae were not detected and yeasts/moulds were low (2.44 log CFU g -1 ). Yeast/mould and Enterobacteriaceae numbers grew considerably during 12 days of air exposure. A mixture of low calibre discarded apples with cowpea stover can be used as animal feed after the ensiling process owing to its nutritive value and long aerobic stability. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Down-selection and optimization of thermal-sprayed coatings for aluminum mould tool protection and upgrade

NASA Astrophysics Data System (ADS)

Gibbons, Gregory John; Hansell, Robert George

2006-09-01

This article details the down-selection procedure for thermally sprayed coatings for aluminum injection mould tooling. A down-selection metric was used to rank a wide range of coatings. A range of high-velocity oxyfuel (HVOF) and atmospheric plasma spray (APS) systems was used to identify the optimal coating-process-system combinations. Three coatings were identified as suitable for further study; two CrC NiCr materials and one Fe Ni Cr alloy. No APS-deposited coatings were suitable for the intended application due to poor substrate adhesion (SA) and very high surface roughness (SR). The DJ2700 deposited coating properties were inferior to the coatings deposited using other HVOF systems and thus a Taguchi L18 five parameter, three-level optimization was used to optimize SA of CRC-1 and FE-1. Significant mean increases in bond strength were achieved (147±30% for FE-1 [58±4 MPa] and 12±1% for CRC-1 [67±5 MPa]). An analysis of variance (ANOVA) indicated that the coating bond strengths were primarily dependent on powder flow rate and propane gas flow rate, and also secondarily dependent on spray distance. The optimal deposition parameters identified were: (CRC-1/FE-1) O2 264/264 standard liters per minute (SLPM); C3H8 62/73 SLPM; air 332/311 SLPM; feed rate 30/28 g/min; and spray distance 150/206 mm.

Wheel liner design for improved sound and structural performances

NASA Astrophysics Data System (ADS)

Oltean, Alexandru; Diaconescu, Claudiu; Tabacu, Ştefan

2017-10-01

Vehicle noise is composed mainly of wheel-road noise and noise from the power unit. At low speeds power unit noise dominates while at high speeds wheel-road noise dominates as wheel-road noise level increases approximately logarithmically with speed. The wheel liner is designed as a component of the vehicle that has a multiple role. It has to prevent the dirt or water from the road surface that are engaged by the wheel to access the engine/front bay. Same time it has the important role to reduce perceived noised in the passenger’s compartment that comes from the wheel-road interaction. Progress in plastic injection moulding technology allowed for new structures to be developed - nonwoven materials in combination with a PP based carrier structure which benefits from a cell structure caused by MuCell injection moulding. The results are light parts with increased sound absorption performances. An adapted combination of materials and production processes can provide the solution for stiff yet soundproofing structures valued for modern vehicles. Sound absorption characteristics of materials used for wheel liners applications were reported in this study. Different polypropylene and polyester fibre-based thermally bonded nonwovens varying in weight and thickness were investigated. Having as a background the performances of the nonwoven material the microcellular structure was part of the analysis. Acoustical absorptive behaviour was explained by analysing the results obtained using the impedance tube and correlating with the knowledge of materials structure.

Fabrication of mandible fracture plate by indirect additive manufacturing

NASA Astrophysics Data System (ADS)

Aizat, M.; Khan, S. F.

2017-10-01

Bone fracture is a serious skeletal injury due to accidents and fragility of the bones at a certain age. In order to accelerate fracture healing process, fracture bone plate is use to hold the fracture segment for more stability. The purpose of this study is to fabricate mandibular fracture plate by using indirect additive manufacturing methods in order to reduce time taken during bending and shaping the fracture fixation plate that conform to the anatomy of the fractured bone site. The design and analysis of the plates are performed using CATIA and ANSYS software. The 3D-CAD data were sent to an additive manufacturing machine (fused filament fabricated) to generate master pattern using PLA and the mould were fabricated using Plaster of Paris. A melt ZAMAK 3 was poured directly into the moulds, and left it until completely harden. 3point bending test was performed on the prototype plate using universal testing machine. Stress-strain curve shows the graph exhibited a linear relationship of stress-strain up to a strain value of 0.001. Specimens give a maximum yielding stress and then break before the conventional deflection. Since the maximum flexural stress and the breaking stress are far apart with a plateau stating at strain value of 0.003mm/mm in most specimens, the specimen’s failure types are considered plastic failure mode. The average thickness and width are 1.65mm and 2.18mm respectively. The flexural modulus and flexural strength are 189.5GPa and 518.1MPa, respectively.

Interlaminar interaction in paper thermoplastic laminate composites

NASA Astrophysics Data System (ADS)

Prambauer, M.; Paulik, C.; Burgstaller, C.

2016-07-01

Bio-based composites are a research topic since several decades, which aims for sustainable and durable materials. In the scope of this research, many different sources for biobased reinforcements have been investigated. Typical issues associated with the use of such are property variations due to cultivation area and climate, besides the influences of the type, pretreatment and fibre geometry. Another issue can be the availability of such natural fibres. Due to these reasons, we started using paper sheets as reinforcements in laminate composites with thermoplastic materials. In preliminary studies with polypropylene composites, we found good mechanical properties, even higher than could be expected by estimating the composite properties from the constituents by applying simple rule of mixtures type models. We suspect, besides some effect of paper compaction, interlaminar effects to be the reason for this. Therefore, the aim of this work is to investigate the effects of the interfacial interaction on the different paper laminate properties due to different matrix polymers. For this work, we used polypropylene, polyamide 6 and 12 as well as polystyrene. Composites were produced via compression moulding and samples for mechanical testing and density evaluation were cut from the moulded plates. The results from mechanical tests show, that there is a reinforcing effect, regardless of matrix polymer used. Simple rule of mixtures evaluations show, that the different matrices exhibit different degrees of interaction, based on their chemical structure. In addition, also influences due to processing were found.

Dried fruits quality assessment by hyperspectral imaging

NASA Astrophysics Data System (ADS)

Serranti, Silvia; Gargiulo, Aldo; Bonifazi, Giuseppe

2012-05-01

Dried fruits products present different market values according to their quality. Such a quality is usually quantified in terms of freshness of the products, as well as presence of contaminants (pieces of shell, husk, and small stones), defects, mould and decays. The combination of these parameters, in terms of relative presence, represent a fundamental set of attributes conditioning dried fruits humans-senses-detectable-attributes (visual appearance, organolectic properties, etc.) and their overall quality in terms of marketable products. Sorting-selection strategies exist but sometimes they fail when a higher degree of detection is required especially if addressed to discriminate between dried fruits of relatively small dimensions and when aiming to perform an "early detection" of pathogen agents responsible of future moulds and decays development. Surface characteristics of dried fruits can be investigated by hyperspectral imaging (HSI). In this paper, specific and "ad hoc" applications addressed to propose quality detection logics, adopting a hyperspectral imaging (HSI) based approach, are described, compared and critically evaluated. Reflectance spectra of selected dried fruits (hazelnuts) of different quality and characterized by the presence of different contaminants and defects have been acquired by a laboratory device equipped with two HSI systems working in two different spectral ranges: visible-near infrared field (400-1000 nm) and near infrared field (1000-1700 nm). The spectra have been processed and results evaluated adopting both a simple and fast wavelength band ratio approach and a more sophisticated classification logic based on principal component (PCA) analysis.

The antifungal efficiency of carbide lime slurry compared with the commercial lime efficiency

NASA Astrophysics Data System (ADS)

Strigac, J.; Mikusinec, J.; Strigacova, J.; Stevulova, N.

2017-10-01

The article deals with studying the antifungal efficiency of carbide lime slurry compared to industrially manufactured commercial lime. Antifungal efficiency expressed as mould proofness properties was tested on the fungi using the procedure given in standard CSN 72 4310. A mixture of fungi Aspergillus niger, Chaetomium globosum, Penicillium funiculosum, Paecilomyces variotii and Gliocladium virens was utilized for testing. The scale for evaluating mould proofness properties according to CSN 72 4310 is from 0 to 5 in degree of fungi growth, where 0 means that no fungi growth occurs and the building products and materials possess fungistatic properties. The study confirms the fungistatic propeties of carbide lime slurry as well as industrially manufactured commercial lime. However, carbide lime slurry and industrially manufactured commercial lime possess no fungicidal effect.

Development of a degradable composite for orthopaedic use: mechanical evaluation of an hydroxyapatite-polyhydroxybutyrate composite material.

PubMed

Boeree, N R; Dove, J; Cooper, J J; Knowles, J; Hastings, G W

1993-08-01

This study evaluates the mechanical properties of a composite material comprising polyhydroxybutyrate with hydroxyapatite added in proportions varying from 0 to 50%. Among the three methods of production, injection moulding was found to result in the most satisfactory mechanical properties. The tensile and compressive strength and the modulus of elasticity of composite produced in this way fell within the range for fresh human bone from different anatomical sites. With the additional advantages of biocompatibility, biodegradability and the potential for piezoelectric stimulation of new local bone formation, it was concluded that the injection-moulded composite material has considerable potential for use in orthopaedic surgery, both as a material to construct certain orthopaedic implants and as an alternative to corticocancellous bone graft.

Higher energy efficient homes are associated with increased risk of doctor diagnosed asthma in a UK subpopulation.

PubMed

Sharpe, Richard A; Thornton, Christopher R; Nikolaou, Vasilis; Osborne, Nicholas J

2015-02-01

The United Kingdom (UK) has one of the highest prevalence of asthma in the world, which represents a significant economic and societal burden. Reduced ventilation resulting from increased energy efficiency measures acts as a modifier for mould contamination and risk of allergic diseases. To our knowledge no previous study has combined detailed asset management property and health data together to assess the impact of household energy efficiency (using the UK Government's Standard Assessment Procedure) on asthma outcomes in an adult population residing in social housing. Postal questionnaires were sent to 3867 social housing properties to collect demographic, health and environmental information on all occupants. Detailed property data, residency periods, indices of multiple deprivation (IMD) and household energy efficiency ratings were also investigated. Logistic regression was used to calculate odds ratios and confidence intervals while allowing for clustering of individuals coming from the same location. Eighteen percent of our target social housing population were recruited into our study. Adults had a mean age of 59 (SD±17.3) years and there was a higher percentage of female (59%) and single occupancy (58%) respondents. Housing demographic characteristics were representative of the target homes. A unit increase in household Standard Assessment Procedure (SAP) rating was associated with a 2% increased risk of current asthma, with the greatest risk in homes with SAP >71. We assessed exposure to mould and found that the presence of a mouldy/musty odour was associated with a two-fold increased risk of asthma (OR 2.2 95%; CI 1.3-3.8). A unit increase in SAP led to a 4-5% reduction in the risk of visible mould growth and a mouldy/musty odour. In contrast to previous research, we report that residing in energy efficient homes may increase the risk of adult asthma. We report that mould contamination increased the risk of asthma, which is in agreement with existing knowledge. Exposure to mould contamination could not fully explain the association between increased energy efficiency and asthma. Our findings may be explained by increased energy efficiency combined with the provision of inadequate heating, ventilation, and increased concentrations of other biological, chemical and physical contaminants. This is likely to be modified by a complex interaction between occupant behaviours and changes to the built environment. Our findings may also be confounded by our response rate, demographic and behavioural differences between those residing in low versus high energy efficient homes, and use of self-reported exposures and outcomes. Energy efficiency may increase the risk of current adult asthma in a population residing in social housing. This association was not significantly modified by the presence of visible mould growth, although further research is needed to investigate the interaction between other demographic and housing characteristic risk factors, especially the impact of fuel poverty on indoor exposures and health outcomes. A multidisciplinary approach is required to assess the interaction between energy efficiency measures and fuel poverty behaviours on health outcomes prior to the delivery of physical interventions aimed at improving the built environment. Policy incentives are required to address fuel poverty issues alongside measures to achieve SAP ratings of 71 or greater, which must be delivered with the provision of adequate heating and ventilation strategies to minimise indoor dampness. Changes in the built environment without changes in behaviour of domicile residents may lead to negative health outcomes. Copyright © 2014 Elsevier Ltd. All rights reserved.

VizieR Online Data Catalog: Palomar Transient Factory photometric observations (Arcavi+, 2014)

NASA Astrophysics Data System (ADS)

Arcavi, I.; Gal-Yam, A.; Sullivan, M.; Pan, Y.-C.; Cenko, S. B.; Horesh, A.; Ofek, E. O.; De Cia, A.; Yan, L.; Yang, C.-W.; Howell, D. A.; Tal, D.; Kulkarni, S. R.; Tendulkar, S. P.; Tang, S.; Xu, D.; Sternberg, A.; Cohen, J. G.; Bloom, J. S.; Nugent, P. E.; Kasliwal, M. M.; Perley, D. A.; Quimby, R. M.; Miller, A. A.; Theissen, C. A.; Laher, R. R.

2017-04-01

All the events from our archival search were discovered by the Palomar 48 inch Oschin Schmidt Telescope (P48) as part of the PTF survey using the Mould R-band filter. We obtained photometric observations in the R and g bands using P48, and in g, r, and i bands with the Palomar 60 inch telescope (P60; Cenko et al. 2006PASP..118.1396C). Initial processing of the P48 images was conducted by the Infrared Processing and Analysis Center (IPAC; Laher et al. 2014PASP..126..674L). Photometry was extracted using a custom PSF fitting routine (e.g., Sullivan et al. 2006AJ....131..960S), which measures the transient flux after image subtraction (using template images taken before the outburst or long after it faded). (1 data file).

Selective growth of palladium and titanium dioxide nanostructures inside carbon nanotube membranes

NASA Astrophysics Data System (ADS)

Hevia, Samuel; Homm, Pía; Cortes, Andrea; Núñez, Verónica; Contreras, Claudia; Vera, Jenniffer; Segura, Rodrigo

2012-06-01

Hybrid nanostructured arrays based on carbon nanotubes (CNT) and palladium or titanium dioxide materials have been synthesized using self-supported and silicon-supported anodized aluminum oxide (AAO) as nanoporous template. It is well demonstrated that carbon nanotubes can be grown using these membranes and hydrocarbon precursors that decompose at temperatures closer to 600°C without the use of a metal catalyst. In this process, carbonic fragments condensate to form stacked graphitic sheets, which adopt the shape of the pores, yielding from these moulds' multi-walled carbon nanotubes. After this process, the ends of the tubes remain open and accessible to other substances, whereas the outer walls are protected by the alumina. Taking advantage of this fact, we have performed the synthesis of palladium and titanium dioxide nanostructures selectively inside carbon nanotubes using these CNT-AAO membranes as nanoreactors.

Selective growth of palladium and titanium dioxide nanostructures inside carbon nanotube membranes.

PubMed

Hevia, Samuel; Homm, Pía; Cortes, Andrea; Núñez, Verónica; Contreras, Claudia; Vera, Jenniffer; Segura, Rodrigo

2012-06-25

Hybrid nanostructured arrays based on carbon nanotubes (CNT) and palladium or titanium dioxide materials have been synthesized using self-supported and silicon-supported anodized aluminum oxide (AAO) as nanoporous template. It is well demonstrated that carbon nanotubes can be grown using these membranes and hydrocarbon precursors that decompose at temperatures closer to 600°C without the use of a metal catalyst. In this process, carbonic fragments condensate to form stacked graphitic sheets, which adopt the shape of the pores, yielding from these moulds' multi-walled carbon nanotubes. After this process, the ends of the tubes remain open and accessible to other substances, whereas the outer walls are protected by the alumina. Taking advantage of this fact, we have performed the synthesis of palladium and titanium dioxide nanostructures selectively inside carbon nanotubes using these CNT-AAO membranes as nanoreactors.

Predicting the microbial exposure risks in urban floods using GIS, building simulation, and microbial models.

PubMed

Taylor, Jonathon; Biddulph, Phillip; Davies, Michael; Lai, Ka man

2013-01-01

London is expected to experience more frequent periods of intense rainfall and tidal surges, leading to an increase in the risk of flooding. Damp and flooded dwellings can support microbial growth, including mould, bacteria, and protozoa, as well as persistence of flood-borne microorganisms. The amount of time flooded dwellings remain damp will depend on the duration and height of the flood, the contents of the flood water, the drying conditions, and the building construction, leading to particular properties and property types being prone to lingering damp and human pathogen growth or persistence. The impact of flooding on buildings can be simulated using Heat Air and Moisture (HAM) models of varying complexity in order to understand how water can be absorbed and dry out of the building structure. This paper describes the simulation of the drying of building archetypes representative of the English building stock using the EnergyPlus based tool 'UCL-HAMT' in order to determine the drying rates of different abandoned structures flooded to different heights and during different seasons. The results are mapped out using GIS in order to estimate the spatial risk across London in terms of comparative flood vulnerability, as well as for specific flood events. Areas of South and East London were found to be particularly vulnerable to long-term microbial exposure following major flood events. Copyright © 2012 Elsevier Ltd. All rights reserved.

Exploring Value-Added Options

Treesearch

Bob Smith; Philip A. Araman

1997-01-01

This paper looks at various opportunities for sawmills to add value to rough sawn lumber. The paper discusses edge-glued panels and blanks, mouldings and millwork, niche market opportunities, and timber bridge members.

Modelling the effect of essential oil of betel leaf (Piper betle L.) on germination, growth, and apparent lag time of Penicillium expansum on semi-synthetic media.

PubMed

Basak, Suradeep; Guha, Proshanta

2015-12-23

The current study aimed at characterizing the chemical components of betel leaf (Piper betle L. var. Tamluk Mitha) essential oil (BLEO) and modelling its effect on growth of Penicillium expansum on semi-synthetic medium. Gas chromatography-mass spectrophotometry (GC-MS) analysis of BLEO revealed the presence of different bioactive phenolic compounds in significant amounts. Among 46 different components identified, chavibetol (22.0%), estragole (15.8%), β-cubebene (13.6%), chavicol (11.8%), and caryophyllene (11.3%) were found to be the major compounds of BLEO. A disc diffusion and disc volatilization method were used to evaluate antifungal activity of the oil against a selected food spoilage mould. The logistic model was used to study the kinetics of spore germination. Prediction and validation of antifungal effect of BLEO was performed on semi-synthetic medium (apple juice agar) using predictive microbiological tools. The Baranyi and Roberts model was used to estimate maximum growth rate (μmax in mm/day) and apparent lag time (λ in days) of the mould. Secondary modelling was performed using a re-parameterized Monod-type equation based on cardinal values to study the effect of different BLEO concentration on estimated growth parameters. Emax (minimum concentration of oil at which mould growth was inhibited) and MIC (minimum inhibitory concentration of BLEO at which lag time is infinite) value of BLEO against P. expansum was estimated to be 0.56 and 0.74 μl/ml, respectively, which was found to be similar on potato dextrose agar (PDA) as well as apple juice agar (AJA) medium. The correlation between estimated growth parameters of the mould on both the media was obtained with satisfactory statistical indices (R(2) and RMSE). This study revealed inhibitory efficacy of BLEO on spore germination, mycelial growth and apparent lag time of P. expansum in a dose-dependent manner. Hence, BLEO has potential to be used as a natural food preservative. Copyright © 2015 Elsevier B.V. All rights reserved.

Prevalence and associated risk factors of chronic bronchitis in First Nations people.

PubMed

Pahwa, Punam; Karunanayake, Chandima P; Rennie, Donna C; Lawson, Joshua A; Ramsden, Vivian R; McMullin, Kathleen; Gardipy, P Jenny; MacDonald, Judy; Abonyi, Sylvia; Episkenew, Jo-Ann; Dosman, James A

2017-06-29

Inadequate housing, low family income, household smoking, personal smoking status, and poor schooling are some of the conditions that have been significantly associated with the prevalence and incidence of chronic bronchitis. The aim of the current study was to determine the prevalence of chronic bronchitis (CB) and associated risk factors among First Nations people. An interviewer-administered survey was conducted as part of the First Nations Lung Health Project in 2012 and 2013 with 874 individuals from 406 households in two First Nations communities located in the province of Saskatchewan, Canada. The questionnaire collected information on individual and contextual determinants of health and a history of ever diagnosed with CB (outcome variable) from the two communities participating in the First Nations Lung Health Project. Clustering effect within households was adjusted using Generalized Estimating Equations. The prevalence of CB was 8.9% and 6.8% among residents (18 years and older) of community A and community B respectively and was not significantly different. CB prevalence was positively associated with odour or musty smell of mildew/mould in the house [OR adj (95% CI) = 2.33 (1.21, 4.50)], allergy to house dust [3.49 (1.75, 6.97)], an air conditioner in home [2.33 (1.18, 4.24)], and increasing age [0.99 (0.33, 2.95), 4.26 (1.74, 10.41), 6.08 (2.58, 14.33)]. An interaction exposure to environmental tobacco smoke in the house*body mass index showed that exposure to household smoke increased the risk of CB for overweight and obese participants (borderline). Some of the variables of interest were not significantly associated with the prevalence of CB in multivariable analysis, possibly due to small numbers. Our results suggest that significant determinants of CB were: increasing age; odour or musty smell of mildew/mould in the house; allergy to house dust; and, body mass index. Modifiable risk factors identified were: (i) community level-housing conditions (such as mould or mildew in home, exposure to environmental tobacco smoke in house); and, (ii) policy level-remediation of mould, and obesity. Not applicable.

3D reconstruction of the structure of a residual limb for customising the design of a prosthetic socket.

PubMed

Shuxian, Zheng; Wanhua, Zhao; Bingheng, Lu

2005-01-01

Aiming at overcoming the limitations of the plaster-casting method in traditional prosthetic socket fabrication, the idea of reconstructing the 3D models for bones and skin of the residual limb is proposed. Given the two-dimensional obtained image through CT scanning, using image processing and reverse engineering techniques, the 3D solid model of the residual limb can be successfully reconstructed. The new approach can reproduce both the internal and the external structure of the residual limb. It can moreover avoid making a positive mould by the way of manual modifications. In addition to this, it can provide a scientific basis for the individualization of prosthetic socket design.

Simultaneous fabrication of a microcavity absorber-emitter on a Ni-W alloy film

NASA Astrophysics Data System (ADS)

Nashun; Kagimoto, Masahiro; Iwami, Kentaro; Umeda, Norihiro

2017-10-01

A process for the simultaneous fabrication of microcavity structures on both sides of a film was proposed and demonstrated to develop a free-standing-type integrated absorber-emitter for use in solar thermophotovoltaic power generation systems. The absorber-emitter-integrated film comprised a heat-resistant Ni-W alloy deposited by electroplating. A two-step silicon mould was fabricated using deep reactive-ion etching and electron beam lithography. Cavity arrays with different unit sizes were successfully fabricated on both sides of the film; these arrays are suitable for use as a solar spectrum absorber and an infrared-selective emitter. Their emissivity spectra were characterised through UV-vis-NIR and Fourier transform infrared spectroscopy.

Analyzing parameters optimisation in minimising warpage on side arm using response surface methodology (RSM)

NASA Astrophysics Data System (ADS)

Rayhana, N.; Fathullah, M.; Shayfull, Z.; Nasir, S. M.; Hazwan, M. H. M.

2017-09-01

This paper presents a systematic methodology to analyse the warpage of the side arm part using Autodesk Moldflow Insight software. Response Surface Methodology (RSM) was proposed to optimise the processing parameters that will result in optimal solutions by efficiently minimising the warpage of the side arm part. The variable parameters considered in this study was based on most significant parameters affecting warpage stated by previous researchers, that is melt temperature, mould temperature and packing pressure while adding packing time and cooling time as these is the commonly used parameters by researchers. The results show that warpage was improved by 10.15% and the most significant parameters affecting warpage are packing pressure.