Validation of limited sampling strategy for the estimation of mycophenolic acid exposure in Chinese adult liver transplant recipients.

PubMed

Hao, Chen; Erzheng, Chen; Anwei, Mao; Zhicheng, Yu; Baiyong, Shen; Xiaxing, Deng; Weixia, Zhang; Chenghong, Peng; Hongwei, Li

2007-12-01

Mycophenolate mofetil (MMF) is indicated as immunosuppressive therapy in liver transplantation. The abbreviated models for the estimation of mycophenolic acid (MPA) area under the concentration-time curve (AUC) have been established by limited sampling strategies (LSSs) in adult liver transplant recipients. In the current study, the performance of the abbreviated models to predict MPA exposure was validated in an independent group of patients. A total of 30 MPA pharmacokinetic profiles from 30 liver transplant recipients receiving MMF in combination with tacrolimus were used to compare 8 models' performance with a full 10 time-point MPA-AUC. Linear regression analysis and Bland-Altman analysis were used to compare the estimated MPA-AUC0-12h from each model against the measured MPA-AUC0-12h. A wide range of agreement was shown when estimated MPA-AUC0-12h was compared with measured MPA-AUC0-12h, and the range of coefficient of determination (r2) was from 0.479 to 0.936. The model based on MPA pharmacokinetic parameters C1h, C2h, C6h, and C8h had the best ability to predict measured MPA-AUC0-12h, with the best coefficient of determination (r2=0.936), the excellent prediction bias (2.18%), the best prediction precision (5.11%), and the best prediction variation (2SD=+/-7.88 mg.h/L). However, the model based on MPA pharmacokinetic sampling time points C1h, C2h, and C4h was more suitable when concerned with clinical convenience, which had shorter sampling interval, an excellent coefficient of determination (r2=0.795), an excellent prediction bias (3.48%), an acceptable prediction precision (14.37%), and a good prediction variation (2SD=+/-13.23 mg.h/L). Measured MPA-AUC0-12h could be best predicted by using MPA pharmacokinetic parameters C1h, C2h, C6h, and C8h. The model based on MPA pharmacokinetic parameters C1h, C2h, and C4h was more feasible in clinical application. Copyright (c) 2007 AASLD.

Competitive FRET-aptamer-based detection of methylphosphonic acid, a common nerve agent metabolite.

PubMed

Bruno, John G; Carrillo, Maria P; Phillips, Taylor; Vail, Neal K; Hanson, Douglas

2008-09-01

Competitive fluorescence resonance energy transfer (FRET)-aptamer-based assay formats are described for one-step detection of methylphosphonic acid (MPA; a metabolite of several organophosphorus (OP) nerve agents). AminoMPA was attached to tosyl-magnetic beads and used for DNA aptamer selection from which one dominant aptamer sequence emerged. Two different FRET approaches were attempted. In one approach, the complementary DNA sequence was used as a template for labeling the aptamer with Alexa Fluor 546 (AF 546)-14-dUTP by asymmetric PCR. Following 3-dimensional (3-D), molecular modeling of the aptamer-MPA complex, a series of three fluoresceinated aptamers labeled at positions 50, 51, and 52 in the putative optimal binding pocket were synthesized. In both FRET formats, aminoMPA was linked to Black Hole Quencher (BHQ-1 or BHQ-2)-succinimides and allowed to bind the fluorescein or AF 546-labeled MPA aptamer. Following gel filtration to purify the labeled MPA aptamer-BHQ-aminoMPA FRET complexes, the complexes were competed against various concentrations of unlabeled MPA, MPA derivatives, and unrelated compounds in titration and cross-reactivity studies. Both approaches yielded low microgram per milliliter detection limits for MPA with generally low levels of cross-reactivity for unrelated compounds. However, the data suggest a pattern of traits that may effect the direction (lights on or off) and intensity of the FRET.

The superiority of the autografts inactivated by high hydrostatic pressure to decellularized allografts in a porcine model.

PubMed

Morimoto, Naoki; Mahara, Atsushi; Jinno, Chizuru; Ogawa, Mami; Kakudo, Natsuko; Suzuki, Shigehiko; Fujisato, Toshia; Kusumoto, Kenji; Yamaoka, Tetsuji

2017-11-01

We are developing a novel skin regeneration therapy in which the inactivation of nevus tissue via high hydrostatic pressure (HHP) is used in the reconstruction of the dermis in combination with a cultured epidermal autograft. In this study, we used a porcine skin graft model to explore whether autologous skin including cellular debris inactivated by HHP or allogeneic skin decellularized by HHP is better for dermal reconstruction. Grafts (n = 6) were prepared for five groups each: autologous skin without pressurization group (control group), autologous skin inactivated by 200 MPa group, autologous skin inactivated by 1000 MPa group, allogeneic skin decellularized by 200 MPa group, and allogeneic skin decellularized by 1000 MPa group. All of the grafts at 1, 4, and 12 weeks showed complete engraftment macroscopically. The mean areas of the grafts of the control group (p < 0.01) and autologous 200 MPa group (p < 0.01) were larger than that of the allogeneic 1000 MPa group at four weeks after implantation. The thickness of the control group and autologous 200 MPa group was comparable, and that of the autologous 200 MPa group was significantly thicker than that of the allogeneic 200 MPa group (p < 0.01). This suggests that the autologous dermis was superior to the allogeneic decellularized dermis as a skin graft, and that HHP at 200 MPa provided a better outcome than HHP at 1000 MPa. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 2653-2661, 2017. © 2016 Wiley Periodicals, Inc.

Study on service performance of 880 MPa-grade and 980 MPa-grade rail steels

NASA Astrophysics Data System (ADS)

Zhu, M.; Xu, G.; Zhou, J. H.; Wang, R. M.; Gan, X. L.

2017-09-01

With the rapid development of economy in China, the requirement for railway passenger and cargo transportation becomes higher and higher. Increasing speed and developing heavy-haul transportation can effectively improve the transportation capacity of railway. The requirement for rail steels with higher ability of abrasion resistance becomes urgent. Two kinds of rails, i.e., 880 MPa-grade and 980 MPa-grade rail steels, were laid on cargo line with 500 m short radius curve. The service performances of the tested steels were continuously tracked and analyzed during operation of total 22.5 million tons loads. Macro morphology, light band width, surface hardness and profile of rails were investigated. The results show that the performance of 980 MPa-grade rail steel is superior to that of 880 MPa-grade rail steel at same circumstance. Therefore, 980 MPa-grade rail should be selected in the cargo line with small radius curve.

Expanding marine protected areas to include degraded coral reefs.

PubMed

Abelson, A; Nelson, P A; Edgar, G J; Shashar, N; Reed, D C; Belmaker, J; Krause, G; Beck, M W; Brokovich, E; France, R; Gaines, S D

2016-12-01

Marine protected areas (MPAs) are a commonly applied solution to coral reef degradation, yet coral reefs continue to decline worldwide. We argue that expanding the range of MPAs to include degraded reefs (DR-MPA) could help reverse this trend. This approach requires new ecological criteria for MPA design, siting, and management. Rather than focusing solely on preserving healthy reefs, our approach focuses on the potential for biodiversity recovery and renewal of ecosystem services. The new criteria would help identify sites with the highest potential for recovery and the greatest resistance to future threats (e.g., increased temperature and acidification) and sites that contribute to MPA connectivity. The DR-MPA approach is a compliment rather than a substitute for traditional MPA design approaches. We believe that the DR-MPA approach can enhance the natural, or restoration-assisted, recovery of DRs and their ecosystem services; increase total reef area available for protection; promote more resilient and better-connected MPA networks; and improve conditions for human communities dependent on MPA ecosystem services. © 2016 The Authors. Conservation Biology published by Wiley Periodicals, Inc. on behalf of Society for Conservation Biology.

Impact reactivity of materials at very high oxygen pressure

NASA Technical Reports Server (NTRS)

Connor, H. W.; Minchey, J. G.; Crowder, R.; Davidson, R.

1983-01-01

The requirements for impact testing of materials in an oxygen atmosphere at pressures from 82.7 MPa (12,000 psi) to 172 MPa (25,000 psi) were evaluated. The impact tester system was evaluated for potential pressure increases from 69 MPa (10,000 psi) to 82.7 MPa (12,000 psi). The low pressure oxygen and nitrogen systems, the impact tower, the impact test cell, and the high pressure oxygen system were evaluated individually. Although the structural integrity of the impact test cell and the compressor were sufficient for operation at 82.7 MPa (12,000 psi), studies revealed possible material incompatibility at that pressure and above. It was recommended that if a component should be replaced for 82.7 MPa (12,000 psi) operation the replacement should meet the final objectives of 172 MPa (25,000 psi). Recommended changes in the system include; use of Monel 400 for pressures above 82.7 MPa (12,000 psi), use of bellows to replace the seal in the impact tester, use of a sapphire window attached to a fiber optic for event sensing, and use of a three diaphragm compressor.

Risk evaluation and mitigation strategies: a focus on the mycophenolic acid preparations.

PubMed

Rostas, Sara; Kim, Miae; Gabardi, Steven

2014-03-01

To review risks associated with mycophenolic acid (MPA) preparations and evaluate their required risk evaluation and mitigation strategies (REMS) elements. Articles were identified through a non-date-limited MEDLINE and EMBASE search using the terms fetal toxicity, teratogenicity, risk evaluation and mitigation strategies, REMS, MPA, mycophenolate mofetil, entericcoated MPA, and organ transplant. Information from the Food and Drug Administration (FDA) and the manufacturers of the MPA preparations was also evaluated. The MPA preparations are associated with several potential risks, including gastrointestinal disturbances and myelosuppression; however, their impact on the fetus in pregnant patients taking 1 of these agents poses the greatest risk. The FDA approved REMS programs for all MPA products, both innovator and generic preparations, in September 2012. With evidence of increased risk of miscarriage and birth defects associated with MPA use, the FDA instituted a REMS program that contains both a medication guide and elements to assure safe use (ETASU). The medication guides for the MPA products, which were previously FDA approved, should continue to be distributed to patients who get either an initial prescription filled or a refill. The ETASU requires prescribers to complete training and obtain patient signatures on the Patient-Prescriber Acknowledgment Form. A single, national, voluntary pregnancy registry specific to this medication has been established, and pregnant patients should be encouraged to participate. Although the impact of the MPA REMS on clinical practice is not clear, it is a step toward increasing the understanding of fetal risks with MPA.

Oligonucleotide microarray analysis of apoptosis induced by 15-methoxypinusolidic acid in microglial BV2 cells

PubMed Central

Choi, Y; Lim, SY; Jeong, HS; Koo, KA; Sung, SH; Kim, YC

2009-01-01

Background and purpose: We conducted a genome wide gene expression analysis to explore the biological aspects of 15-methoxypinusolidic acid (15-MPA) isolated from Biota orientalis and tried to confirm the suitability of 15-MPA as a therapeutic candidate for CNS injuries focusing on microglia. Experimental approach: Murine microglial BV2 cells were treated with 15-MPA, and their transcriptome was analysed by using oligonucleotide microarrays. Genes differentially expressed upon 15-MPA treatment were selected for RT-PCR (reverse transcription-polymerase chain reaction) analysis to confirm the gene expression. Inhibition of cell proliferation and induction of apoptosis by 15-MPA were examined by bromodeoxyuridine assay, Western blot analysis of poly-ADP-ribose polymerase and flow cytometry. Key results: A total of 514 genes were differentially expressed by 15-MPA treatment. Biological pathway analysis revealed that 15-MPA induced significant changes in expression of genes in the cell cycle pathway. Genes involved in growth arrest and DNA damage [gadd45α, gadd45γ and ddit3 (DNA damage-inducible transcript 3)] and cyclin-dependent kinase inhibitor (cdkn2b) were up-regulated, whereas genes involved in cell cycle progression (ccnd1, ccnd3 and ccne1), DNA replication (mcm4, orc1l and cdc6) and cell proliferation (fos and jun) were down-regulated. RT-PCR analysis for representative genes confirmed the expression levels. 15-MPA significantly reduced bromodeoxyuridine incorporation, increased poly-ADP-ribose polymerase cleavage and the number of apoptotic cells, indicating that 15-MPA induces apoptosis in BV2 cells. Conclusion and implications: 15-MPA induced apoptosis in murine microglial cells, presumably via inhibition of the cell cycle progression. As microglial activation is detrimental in CNS injuries, these data suggest a strong therapeutic potential of 15-MPA. PMID:19466985

Field Sandbur (Cenchrus pauciflorus) Seeds in the Same Bur Respond Differently to Temperature and Water Potential in Relation to Germination in a Semi-Arid Environment, China

PubMed Central

Bai, Yuguang; Liu, Huifang; Niu, Xueli; Wang, Zhiwei; Wang, Qian

2016-01-01

The success of a biological invasion relies on the environment and is closely linked to factors such as water and temperature. Invasive plant species display different seed characteristics, including shape. Field sandbur (Cenchrus pauciflorus) is a globally widespread invasive species capable of adapting to broad environmental conditions. However, its germination response to water and temperature still remains unclear. C. pauciflorus contains two seeds in the same bur that differ in size: big seeds (M) and small seeds (P). Separate greenhouse experiments were conducted under different temperature regimes (0/10°C, 5/15°C, 10/20°C, 15/25°C, 18/28°C, 20/30°C and 25/35°C) and water potentials (-1.50Mpa, -1.00Mpa, -0.75Mpa, -0.50Mpa, -0.25Mpa and 0Mpa) for M and P seeds. The results support the hypothesis that germination of C. pauciflorus is significantly influenced by seed type, temperature and water potential. M and P seeds responded differently to varied alternative temperatures and water potentials. However, M and P seeds were more sensitive to water potential than to temperature. Optimal conditions for M and P seed germination were measured at 25/35°C (night temperature/day temperature) and 20/30°C, respectively. In contrast, the highest germination rate was observed for the 0Mpa of the water potential treatment. Additionally, base temperature (Tbase) and base water potential (Wbase) were lower for M (7.7°C, -1.11Mpa at 10/20°C, and -1.07Mpa at 20/30°C) than for P (9.4°C, -0.92Mpa at 10/20°C, and -0.52Mpa at 20/30°C). These different germination strategies of M and P seeds with respect to temperature and water potential increased overall plant propagation. These results indicate that tropical and subtropical regions water potentials beyond -0.50Mpa (10/20°C) or -1.00Mpa (20/30°C) face a potential risk of C. pauciflorus invasion. PMID:27992496

Field Sandbur (Cenchrus pauciflorus) Seeds in the Same Bur Respond Differently to Temperature and Water Potential in Relation to Germination in a Semi-Arid Environment, China.

PubMed

Zhang, Zhixin; Tian, Xun; Bai, Yuguang; Liu, Huifang; Niu, Xueli; Wang, Zhiwei; Wang, Qian

2016-01-01

The success of a biological invasion relies on the environment and is closely linked to factors such as water and temperature. Invasive plant species display different seed characteristics, including shape. Field sandbur (Cenchrus pauciflorus) is a globally widespread invasive species capable of adapting to broad environmental conditions. However, its germination response to water and temperature still remains unclear. C. pauciflorus contains two seeds in the same bur that differ in size: big seeds (M) and small seeds (P). Separate greenhouse experiments were conducted under different temperature regimes (0/10°C, 5/15°C, 10/20°C, 15/25°C, 18/28°C, 20/30°C and 25/35°C) and water potentials (-1.50Mpa, -1.00Mpa, -0.75Mpa, -0.50Mpa, -0.25Mpa and 0Mpa) for M and P seeds. The results support the hypothesis that germination of C. pauciflorus is significantly influenced by seed type, temperature and water potential. M and P seeds responded differently to varied alternative temperatures and water potentials. However, M and P seeds were more sensitive to water potential than to temperature. Optimal conditions for M and P seed germination were measured at 25/35°C (night temperature/day temperature) and 20/30°C, respectively. In contrast, the highest germination rate was observed for the 0Mpa of the water potential treatment. Additionally, base temperature (Tbase) and base water potential (Wbase) were lower for M (7.7°C, -1.11Mpa at 10/20°C, and -1.07Mpa at 20/30°C) than for P (9.4°C, -0.92Mpa at 10/20°C, and -0.52Mpa at 20/30°C). These different germination strategies of M and P seeds with respect to temperature and water potential increased overall plant propagation. These results indicate that tropical and subtropical regions water potentials beyond -0.50Mpa (10/20°C) or -1.00Mpa (20/30°C) face a potential risk of C. pauciflorus invasion.

Optical monitoring of ultrasound-induced bioeffects in glass catfish.

PubMed

Maruvada, Subha; Hynynen, Kullervo

2004-01-01

This study is an investigation of the therapeutic ultrasound (US) effects on the blood vessels of optically transparent fish in vivo. Although many investigators have characterized cavitation in vivo using remote-sensing methods (i.e., measuring the acoustic emissions caused by oscillating bubbles) very few have made direct observations of cavitation-induced damage. Anesthetized glass catfish, which are optically transparent, was injected with the contrast agent, Optison, and then insonified at pressures that ranged from 0.5-10 MPa (peak negative pressures). Two focused transducers were used in these experiments to cover a frequency range of 0.7-3.3 MHz. Sonications were pulsed with pulse durations of 100, 10, 1, 0.1 and 0.01 ms and a pulse repetition frequency (PRF) of 1 Hz. The entire length of one sonication at a specific pressure level was 20 s. An inverted microscope combined with a digital camera and video monitor were used optically to monitor and record US interaction with the blood vessels in the tail of the anesthetized fish at 200x magnification. The effects of the burst sonication were analyzed visually at each pressure level. For the 1.091-MHz sonications, the first type of damage that occurred due to the US interaction was structural damage to the cartilage rods that comprise the tail of the fish, and was characterized by a disintegration of the lining of the rod. Damage to the rods occurred, starting at 3.5 MPa, 3.1 MPa, 4.1 MPa and 5.5 MPa for the 100-ms, 10-ms, 1-ms and 100-micros sonications, respectively. The formation of large gas bubbles was observed in the blood vessels of the fish at threshold values of 3.8 MPa, 3.8 MPa and 5.3 MPa, for the 100-ms, 10-ms and 1-ms sonications, respectively. Neither gas bubble formation nor hemorrhaging was observed during 100-micros sonications. Bubble formation was always accompanied by an increase of damage to the rods at the area surrounding the bubble. At 1.091 MHz, petechial hemorrhage thresholds were observed at 4.1 MPa, 4.1 MPa and 6.1 MPa, respectively, for the three pulse durations. The thresholds for damage were the lowest for the 0.747-MHz sonications: they were 2.6 MPa for damage to the rods, 3.7 MPa for gas bubble formation and 2.4 MPa for hemorrhaging.

Effect of surface modifications on the bond strength of zirconia ceramic with resin cement resin.

PubMed

Hallmann, Lubica; Ulmer, Peter; Lehmann, Frank; Wille, Sebastian; Polonskyi, Oleksander; Johannes, Martina; Köbel, Stefan; Trottenberg, Thomas; Bornholdt, Sven; Haase, Fabian; Kersten, Holger; Kern, Matthias

2016-05-01

Purpose of this in vitro study was to evaluate the effect of surface modifications on the tensile bond strength between zirconia ceramic and resin. Zirconia ceramic surfaces were treated with 150-μm abrasive alumina particles, 150-μm abrasive zirconia particles, argon-ion bombardment, gas plasma, and piranha solution (H2SO4:H2O2=3:1). In addition, slip casting surfaces were examined. Untreated surfaces were used as the control group. Tensile bond strengths (TBS) were measured after water storage for 3 days or 150 days with additional 37,500 thermal cycling for artificial aging. Statistical analyses were performed with 1-way and 3-way ANOVA, followed by comparison of means with the Tukey HSD test. After storage in distilled water for three days at 37 °C, the highest mean tensile bond strengths (TBS) were observed for zirconia ceramic surfaces abraded with 150-μm abrasive alumina particles (TBS(AAP)=37.3 MPa, TBS(CAAP)=40.4 MPa), and 150-μm abrasive zirconia particles (TBS(AZP)=34.8 MPa, TBS(CAZP)=35.8 MPa). Also a high TBS was observed for specimens treated with argon-ion bombardment (TBS(BAI)=37.8 MPa). After 150 days of storage, specimens abraded with 150-μm abrasive alumina particles and 150-μm abrasive zirconia particles revealed high TBS (TBS(AAP)=37.6 MPa, TBS(CAAP)=33.0 MPa, TBS(AZP)=22.1 MPa and TBS(CAZP)=22.8 MPa). A high TBS was observed also for specimens prepared with slip casting (TBS(SC)=30.0 MPa). A decrease of TBS was observed for control specimens (TBS(UNT)=12.5 MPa, TBS(CUNT)=9.0 MPa), specimens treated with argon-ion bombardment (TBS(BAI)=10.3 MPa) and gas plasma (TBS(GP)=11.0 MPa). A decrease of TBS was observed also for specimens treated with piranha solution (TBS(PS)=3.9 MPa, TBS(CPS)=4.1 MPa). A significant difference in TBS after three days storage was observed for specimens treated with different methods (p<0.001). Thermal cycling significantly reduced TBS for all groups (p<0.001) excluding groups: AAP(p>0.05), CAAP(p>0.05) and SC(p>0.05). However, the failure patterns of debonded specimens prepared with 150-μm abrasive zirconia particles were 96.7% cohesive. Treatment of zirconia ceramic surfaces with abrasive zirconia particles is a promising method to increase the tensile bond strength without significant damage of the ceramic surface itself. An alternative promising method is slip casting. Copyright © 2016 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Physical activity helps to control music performance anxiety.

PubMed

Rocha, Sérgio F; Marocolo, Moacir; Corrêa, Elisangela N V; Morato, Gledys S G; da Mota, Gustavo R

2014-06-01

We evaluated if regular physical activity could influence musical performance anxiety (MPA) in college music students. Levels of MPA, as measured with the Kenny MPA Inventory, and a survey about the physical activity habits were obtained from 87 students of music. The results showed that physically active musicians had lower MPA scores (p<0.05) than non-active ones, independent of gender. We conclude that there is an association between physical activity and minor MPA, and studies with a longitudinal design should be done to explore this important issue.

The combined effect of high pressure and nisin or lysozyme on the inactivation of Alicyclobacillus acidoterrestris spores in apple juice

NASA Astrophysics Data System (ADS)

Sokołowska, B.; Skąpska, S.; Fonberg-Broczek, M.; Niezgoda, J.; Chotkiewicz, M.; Dekowska, A.; Rzoska, S.

2012-03-01

Alicyclobacillus acidoterrestris, a thermoacidophilic and spore-forming bacterium is one of the important target micro-organisms in the quality control of acidic canned foods. High pressure pasteurization (HPP) at 50°C was used for the inactivation of A. acidoterrestris spores in apple juice. Pressure applied both in a continuous and oscillatory mode gave the best results when 200 MPa was used. Increasing the pressure to 500 MPa, as well as lowering its value to 100 MPa, had an adverse effect on the effectiveness of the process. The best results were achieved with the use of a combined treatment, involving oscillatory pressurization at 200 MPa, followed by holding the sample for 60 min at atmospheric pressure and subsequent pressurization at 500 MPa, resulting in a reduction in the spore count of 6.15 log. Nisin significantly enhanced the effect of HPP at 300 MPa. Using pressure of 200 MPa for 45 min with a nisin concentration of 250 IU/mL enabled total spore inactivation (over 6 log). No significant effect of lysozyme at a concentration of 0.05 and 0.1 mg/L at 300 MPa was observed.

Effect of high pressures on the enzymatic activity of commercial milk protein coagulants

NASA Astrophysics Data System (ADS)

Wiśniewska, Krystyna; Reps, Arnold; Jankowska, Agnieszka

2014-04-01

This study was aimed at determining the effect of high pressures in the range of 100-1000 MPa/15 min, applied in 100 MPa increments, on the coagulating and proteolytic activity of commercial coagulants produced with genetic engineering methods: Maxiren, Chymogen, Chymax and of a natural rennin preparation, Hala. The coagulating activity of Hala preparation differed compared with the other preparations, due to greater resistance to high pressures, especially in the range of 500-600 MPa. The preparations produced with genetic engineering methods lost their capability for milk protein coagulation by 500 MPa. Pressurization at 200 MPa contributed to their reduced capability for casein macroproteolysis. In contrast, an increase in Chymax, Chymogen, Maxiren and Hala preparations' hydrolytic capability for the macroproteolysis of isoelectric casein was observed upon pressure treatment at 100 and 400 MPa and for microproteolysis after pressure treatment at 200 MPa. Storage (48 h/5°C) of the pressurized preparations had an insignificant effect on their coagulating and proteolytic activities.

Effects of different hydrostatic pressure on lesions in ex vivo bovine livers induced by high intensity focused ultrasound.

PubMed

He, Min; Zhong, Zhiqiang; Li, Xing; Gong, Xiaobo; Wang, Zhibiao; Li, Faqi

2017-05-01

It is well-known that acoustic cavitation associated with the high intensity focused ultrasound (HIFU) treatment often would change the morphology and size of lesions in its treatment. In most studies reported in literature, high ambient hydrostatic pressure was used to suppress the cavitation completely. Investigation of the effects by varying the ambient hydrostatic pressure (P stat ) is still lacking. In this paper, the effects of HIFU on lesions in ex vivo bovine liver specimens under various P stat are systematically investigated. A 1MHz HIFU transducer, with an aperture diameter of 70mm and a focal length of 55mm, was used to generate two groups US exposure of different acoustic intensities and exposure time (6095W/cm 2 ×8s and 9752W/cm 2 ×5s), while keeping the same acoustic energies per unit area (48760J/cm 2 ). The peak acoustic negative pressures (p - ) of the two groups were p 1 - =9.58MPa and p 2 - =10.82MPa, respectively, with the difference p d - =p 2 - -p 1 - =1.24MPa. A passive cavitation detection (PCD) was used to monitor the ultrasonic cavitation signal during exposure of the two groups. The US exposures were done under the following ambient hydrostatic pressures, P stat : atmospheric pressure, 0.5MPa, 1.0MPa, 1.5MPa, 2.0MPa, 2.5MPa and3.0MPa, respectively. The result of PCD showed that there was a statistically significant increase above background noise level in broadband emissions at dose of 9752W/cm 2 ×5s, but not at dose of 6095W/cm 2 ×8s under atmospheric pressure; i.e., the acoustic cavitation took place for p 2 - but not for p 1 - when under atmospheric pressure. The results also showed that there was no statistically difference of the morphology and size of lesions for 6095W/cm 2 ×8s exposure under the aforementioned different ambient hydrostatic pressures. But the lesions generated at 9752W/cm 2 ×5s exposure under P stat =atmospheric pressure, 0.5MPa, 1.0MPa (all of them are less than p d - ), were larger than those under 1.5MPa, 2.0MPa, 2.5MPa and 3.0MPa (all of them are over than p d - ) which were consistence with 6095W/cm 2 ×8s group. It was concluded that when P stat >p d - , the acoustic cavitation was suppressed and prompted that there was no need to elevate P stat higher than p - to suppress the acoustic cavitation in tissue, just need P stat higher than p d - . Copyright © 2016 Elsevier B.V. All rights reserved.

Mycophenolic acid induces ATP-binding cassette transporter A1 (ABCA1) expression through the PPAR{gamma}-LXR{alpha}-ABCA1 pathway

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Yanni; Lai, Fangfang; Xu, Yang

2011-11-04

Highlights: Black-Right-Pointing-Pointer Using an ABCA1p-LUC HepG2 cell line, we found that MPA upregulated ABCA1 expression. Black-Right-Pointing-Pointer MPA induced ABCA1 and LXR{alpha} protein expression in HepG2 cells. Black-Right-Pointing-Pointer PPAR{gamma} antagonist GW9662 markedly inhibited MPA-induced ABCA1 and LXR{alpha} protein expression. Black-Right-Pointing-Pointer The effect of MPA upregulating ABCA1 was due mainly to activation of the PPAR{gamma}-LXR{alpha}-ABCA1 pathway. -- Abstract: ATP-binding cassette transporter A1 (ABCA1) promotes cholesterol and phospholipid efflux from cells to lipid-poor apolipoprotein A-I and plays an important role in atherosclerosis. In a previous study, we developed a high-throughput screening method using an ABCA1p-LUC HepG2 cell line to find upregulators of ABCA1.more » Using this method in the present study, we found that mycophenolic acid (MPA) upregulated ABCA1 expression (EC50 = 0.09 {mu}M). MPA upregulation of ABCA1 expression was confirmed by real-time quantitative reverse transcription-PCR and Western blot analysis in HepG2 cells. Previous work has indicated that MPA is a potent agonist of peroxisome proliferator-activated receptor gamma (PPAR{gamma}; EC50 = 5.2-9.3 {mu}M). Liver X receptor {alpha} (LXR{alpha}) is a target gene of PPAR{gamma} and may directly regulate ABCA1 expression. Western blot analysis showed that MPA induced LXR{alpha} protein expression in HepG2 cells. Addition of PPAR{gamma} antagonist GW9662 markedly inhibited MPA-induced ABCA1 and LXR{alpha} protein expression. These data suggest that MPA increased ABCA1 expression mainly through activation of PPAR{gamma}. Thus, the effects of MPA on upregulation of ABCA1 expression were due mainly to activation of the PPAR{gamma}-LXR{alpha}-ABCA1 signaling pathway. This is the first report that the antiatherosclerosis activity of MPA is due to this mechanism.« less

Active and Repressive Chromatin-Associated Proteome after MPA Treatment and the Role of Midkine in Epithelial Monolayer Permeability

PubMed Central

Khan, Niamat; Lenz, Christof; Binder, Lutz; Pantakani, Dasaradha Venkata Krishna; Asif, Abdul R.

2016-01-01

Mycophenolic acid (MPA) is prescribed to maintain allografts in organ-transplanted patients. However, gastrointestinal (GI) complications, particularly diarrhea, are frequently observed as a side effect following MPA therapy. We recently reported that MPA altered the tight junction (TJ)-mediated barrier function in a Caco-2 cell monolayer model system. This study investigates whether MPA induces epigenetic changes which lead to GI complications, especially diarrhea. Methods: We employed a Chromatin Immunoprecipitation-O-Proteomics (ChIP-O-Proteomics) approach to identify proteins associated with active (H3K4me3) as well as repressive (H3K27me3) chromatin histone modifications in MPA-treated cells, and further characterized the role of midkine, a H3K4me3-associated protein, in the context of epithelial monolayer permeability. Results: We identified a total of 333 and 306 proteins associated with active and repressive histone modification marks, respectively. Among them, 241 proteins were common both in active and repressive chromatin, 92 proteins were associated exclusively with the active histone modification mark, while 65 proteins remained specific to repressive chromatin. Our results show that 45 proteins which bind to the active and seven proteins which bind to the repressive chromatin region exhibited significantly altered abundance in MPA-treated cells as compared to DMSO control cells. A number of novel proteins whose function is not known in bowel barrier regulation were among the identified proteins, including midkine. Our functional integrity assays on the Caco-2 cell monolayer showed that the inhibition of midkine expression prior to MPA treatment could completely block the MPA-mediated increase in barrier permeability. Conclusions: The ChIP-O-Proteomics approach delivered a number of novel proteins with potential implications in MPA toxicity. Consequently, it can be proposed that midkine inhibition could be a potent therapeutic approach to prevent the MPA-mediated increase in TJ permeability and leak flux diarrhea in organ transplant patients. PMID:27104530

High specificity ZnO quantum dots for diagnosis and treatment in bacterial infection

NASA Astrophysics Data System (ADS)

Zhang, Min; Qian, Zhiyu; Gu, Yueqing

2016-03-01

Early diagnosis and effective treatment of bacterial infection has become increasingly important. Herein, we developed a fluorescent nano-probe MPA@ZnO-PEP by conjugating SiO2-stabilized ZnO quantum dot (ZnO@SiO2) with bacteria-targeting peptide PEP, which was encapsulated with MPA, a near infrared (NIR) dye. The nanoprobe MPA@ZnO-PEP showed excellent fluorescence property and could specifically distinguish bacterial infection from sterile inflammation both in vitro and in vivo. The favorable biocompatability of MPA@ZnO-PEP was verified by MTT assay. This probe was further modified with antibiotic methicillin to form the theranostic nanoparticle MPA/Met@ZnO-PEP with amplified antibacterial activity. These results promised the great potential of MPA@ZnO-PEP for efficient non-invasive early diagnosis of bacterial infections and effective bacterial-targeting therapy.

Colorimetric detection of mercury(II) in a high-salinity solution using gold nanoparticles capped with 3-mercaptopropionate acid and adenosine monophosphate.

PubMed

Yu, Cheng-Ju; Tseng, Wei-Lung

2008-11-04

A new colorimetric sensor for sensing Hg2+ in a high-salinity solution has been developed using gold nanoparticles (AuNPs) decorated with 3-mercaptopropionate acid (MPA) and adenosine monophosphate (AMP). Because of the high negative charge density of AMP on each AuNP surface, MPA/AMP-capped AuNPs are well dispersed in a high-salt solution. In contrast, the aggregation of MPA-capped AuNPs was induced by sodium ions, which shield the negative charges of the carboxylic groups of MPA. Through the coordination between the carboxylic group of MPA and Hg2+, the selectivity of MPA/AMP-capped AuNPs for Hg2+ in a high-salt solution is remarkably high over that of the other metals without the addition of a masking agent or a change in the temperature. We have carefully investigated the effect of the AMP concentration on the stability and sensitivity of MPA/AMP-capped AuNPs. Under optimum conditions, the lowest detectable concentration of Hg2+ using this probe was 500 nM on the basis of the measurement of the ratio of absorption at 620 nm to that at 520 nm. The sensitivity to Hg2+ can be further improved by modifying the MPA/AMP-capped AuNPs with highly fluorescent rhodamine 6G (R6G). By monitoring the fluorescence enhancement, the lowest detectable concentration of Hg2+ using R6G/MPA/AMP-capped AuNPs was 50 nM.

Immobilization technique for enhanced production of the immunosuppressant mycophenolic acid by ultraviolet and gamma-irradiated Penicillium roqueforti.

PubMed

Ismaiel, A A; Ahmed, A S; El-Sayed, E R

2015-07-01

Different entrapment matrices were screened to immobilize two strains of Penicillium roqueforti (AG101 and LG109) for more effective production of mycophenolic acid (MPA). Further improvement in the MPA productivity from immobilization of spores and mycelia was adopted by UV and gamma irradiation. Penicillium roqueforti strains were immobilized in different entrapping carriers and used for MPA production in shake flask cultures. Maximum MPA production was achieved on using an alginate concentration of 3·0% (w/v) and a mycelial fresh weight of 10% (w/v). MPA produced by alginate-immobilized spores and mycelia was almost double in comparison to the free system. The MPA-producing ability of immobilized AG101 and LG109 strain was significantly enhanced by mutagenesis through irradiation by UV (254 nm) for 120 and 90 min, respectively and gamma rays at 0·75 KGy. The feasibility of MPA production in a semi-continuous form by immobilized cells as affected by irradiation was adopted. MPA production by immobilized spores and mycelia was more intensified by UV and gamma irradiation. Moreover, the immobilized cell culture was superior to free-cell culture. These findings indicate the future possibility to reduce the cost of producing fermentation-based drugs. © 2015 The Society for Applied Microbiology.

Probing into the binding interaction between medroxyprogesterone acetate and bovine serum albumin (BSA): spectroscopic and molecular docking methods.

PubMed

Fang, Fang; Pan, Dong-Qi; Qiu, Min-Jie; Liu, Ting-Ting; Jiang, Min; Wang, Qi; Shi, Jie-Hua

2016-09-01

To further understand the mechanism of action and pharmacokinetics of medroxyprogesterone acetate (MPA), the binding interaction of MPA with bovine serum albumin (BSA) under simulated physiological conditions (pH 7.4) was studied using fluorescence emission spectroscopy, synchronous fluorescence spectroscopy, circular dichroism and molecular docking methods. The experimental results reveal that the fluorescence of BSA quenches due to the formation of MPA-BSA complex. The number of binding sites (n) and the binding constant for MPA-BSA complex are ~1 and 4.6 × 10(3)  M(-1) at 310 K, respectively. However, it can be concluded that the binding process of MPA with BSA is spontaneous and the main interaction forces between MPA and BSA are van der Waals force and hydrogen bonding interaction due to the negative values of ΔG(0) , ΔH(0) and ΔS(0) in the binding process of MPA with BSA. MPA prefers binding on the hydrophobic cavity in subdomain IIIA (site II'') of BSA resulting in a slight change in the conformation of BSA, but BSA retaining the α-helix structure. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Navigating future uncertainty in marine protected area governance: Lessons from the Scottish MPA network

NASA Astrophysics Data System (ADS)

Hopkins, Charlotte Rachael; Bailey, David Mark; Potts, Tavis

2018-07-01

As international pressure for marine protection has increased, Scotland has increased spatial protection through the development of a Marine Protected Area (MPA) network. Few MPA networks to date have included specific considerations of climate change in the design, monitoring or management of the network. The Scottish MPA network followed a feature-led approach to identify a series of MPAs across the Scottish marine area and incorporated the diverse views of many different stakeholders. This feature led approach has led to wide ranging opinions and understandings regarding the success of the MPA network. Translating ideas of success into a policy approach whilst also considering how climate change may affect these ideas of success is a complex challenge. This paper presents the results of a Delphi process that aimed to facilitate clear communication between academics, policy makers and stakeholders in order to identify specific climate change considerations applicable to the Scottish MPA network. This study engaged a group of academic and non-academic stakeholders to discuss potential options that could be translated into an operational process for management of the MPA network. The results of Delphi process discussion are presented with the output of a management matrix tool, which could aid in future decisions for MPA management under scenarios of climate change.

Effects of high pressure freezing (HPF) on denaturation of natural actomyosin extracted from prawn (Metapenaeus ensis).

PubMed

Cheng, Lina; Sun, Da-Wen; Zhu, Zhiwei; Zhang, Zhihang

2017-08-15

Effects of protein denaturation caused by high pressure freezing, involving Pressure-Factors (pressure, time) and Freezing-Factors (temperature, phase transition, recrystallization, ice crystal types), are complicated. In the current study, the conformation and functional changes of natural actomyosin (NAM) under pressure assisted freezing (PAF, 100,150,300,400,500MPa P -20°C/25min ), pressure shift freezing (PSF, 200MPa P -20°C/25min ), and immersion freezing ( 0.1MPa P -20°C/5min ) after pressure was released to 0.1MPa, as compared to normal immersion freezing process (IF, 0.1MPa P -20°C/30min ). Results indicated that PSF ( 200MPa P -20°C/30min ) could reduce the denaturation of frozen NAM and a pressure of 300MPa was the critical point to induce such a denaturation. During the periods of B→D in PSF or B→C→D in PAF, the generation and growth of ice crystals played an important role on changing the secondary and tertiary structure of the treated NAM. Copyright © 2017 Elsevier Ltd. All rights reserved.

Accelerated aging characteristics of three yttria-stabilized tetragonal zirconia polycrystalline dental materials.

PubMed

Flinn, Brian D; deGroot, Dirk A; Mancl, Lloyd A; Raigrodski, Ariel J

2012-10-01

Concerns have been expressed about the effect of aging on the mechanical properties of zirconia. The purpose of this study was to assess the accelerated aging characteristics of 3 commercially available yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) materials by exposing specimens to hydrothermal treatments at 134°C, 0.2 MPa and 180°C, 1.0 MPa in steam. Thin bars of Y-TZP from 3 manufacturers, Lava, Zirkonzahn, and Zirprime, n=30 for each brand (22 × 3 × 0.2 mm), were cut and ground from blocks and sintered according to the manufacturer's specifications. Control specimens (n=10) for each brand were evaluated in the as-received condition. Experimental specimens were artificially aged at standard autoclave sterilization conditions,134°C at 0.2 MPa (n=5 per group at 50, 100, 150, and 200 hours) and standard industrial ceramic aging conditions, 180°C at 1.0 MPa (n=5 per group at 8, 16, 24, 28, and 48 hours). Tetragonal to monoclinic transformation was measured by using X-ray diffraction (XRD) for all groups. Flexural strength was measured in 4-point bending (ASTM1161-B) for all groups. Fracture surfaces were examined by scanning electron microscopy (SEM). Data were analyzed as a function of aging time. The statistical comparisons were based on the log value and 2-way ANOVA with heteroscedasticity-consistent standard errors used to compare mean strength among conditions (α=.05). After 200 hours at 134°C and 0.2 MPa, flexural strength (SD) decreased significantly from 1156 (87.6) MPa to 829.5 (71) MPa for Lava; 1406 (243) MPa to 882.7 (91) MPa for Zirkonzahn; and 1126 (92.4) MPa to 976 (36.4) MPa for Zirprime with P<.001 for all 3 comparisons. After 200 hours at 134°C and 0.2 MPa, some tetragonal crystals transformed to the monoclinic phase. The relative XRD peak intensity of the monoclinic to tetragonal crystal phases increased from 0.07 to 1.82 for Lava, from 0.06 to 2.43 for Zirkonzahn, and from 0.05 to 0.53 for Zirprime. After 28 hours at 180°C and 1.0 MPa, all Lava and Zirkonzahn specimens spontaneously fractured during aging. The Noritake specimens were intact after 48 hours, and the flexural strength showed no significant change, 1156 (87.6) MPa to 1122 (108) MPa. The flexural strength decreased with an increase in the monoclinic phase. SEM micrographs revealed a transformed layer on the fracture surfaces. Hydrothermal aging of Y-TZP can cause significant transformation from tetragonal to monoclinic crystal structure, which results in a statistically significant decrease in the flexural strength of thin bars. Although the strengths of all 3 Y-TZP materials are higher than other materials used for ceramic restorations, there are notable differences among them. Copyright © 2012 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

New Insights on the Creeping Phase of the Vajont Landslide form Rotary-Shear Experiments

NASA Astrophysics Data System (ADS)

Ferri, F.; Spagnuolo, E.; Di Felice, F.; Di Toro, G.

2014-12-01

It is well known that 1963 catastrophic Vajont landslide (NE Italy) was preceded by a creeping phase monitored over three years before the collapse and that water played a significant role in the instability of the rock sequence. However, the transition from the creeping phase to instability still remains elusive. Here we report experiments carried out in a rotary-shear friction apparatus (SHIVA at INGV, Rome, Italy) on smectite-rich gouges collected from the landslide surface (60-70% smectite, 20-30% calcite and minor quartz). Experiments were performed under shear stress controlled conditions at normal stress σnof 3-5 MPa in the presence of water (20% weight), and at room humidity. During the experiments, the shear stress τ was increased by a constant value Δτ and maintained for a fixed time Δt before applying the following shear stress step. When frictional instability was achieved, the machine started to rotate at an imposed velocity. In the first set of experiments, the initial τ (0.05 MPa) was increased by steps of Δτ = 0.25 MPa with Δt of 150 seconds. In the room humidity material, a series of spontaneous slip bursts occurred at τ = 2.5 MPa (at σn = 5MPa) until the shear stress reached 3.0 MPa. At this point, a large stress drop occurred with concomitant dilation. In the wet material, instability took place at τ= 0.3 MPa (at σn= 3 MPa). After forcing τ down, the material re-strengthened. A second main instability occurred when τ was restored to 0.3 MPa, with expulsion of water drops accompanied by an episode of dilation. At this point, the material spontaneously re-strengthened with a stick-slip behavior similar to that observed at room humidity conditions. In the second set of experiments, Δτ was reduced to 0.05 MPa and Δt increased up to 360 seconds producing a general enhancement of the shear stress required to generate unstable sliding. Instability took place at very high τ (3.12 MPa at σn= 3 MPa) at room-humidity conditions, and at τ = 0.8-0.9 MPa at wet conditions. The experiments evidence that the frictional instability of the Vajont clays is strongly dependent on the presence of water and on the shear stress enhancement Δτ. The results are important to model the frictional variation on the sliding surface concomitant with the fluctuations of the dam reservoir level.

Antiandrogenic actions of medroxyprogesterone acetate on epithelial cells within normal human breast tissues cultured ex vivo.

PubMed

Ochnik, Aleksandra M; Moore, Nicole L; Jankovic-Karasoulos, Tanja; Bianco-Miotto, Tina; Ryan, Natalie K; Thomas, Mervyn R; Birrell, Stephen N; Butler, Lisa M; Tilley, Wayne D; Hickey, Theresa E

2014-01-01

Medroxyprogesterone acetate (MPA), a component of combined estrogen-progestin therapy (EPT), has been associated with increased breast cancer risk in EPT users. MPA can bind to the androgen receptor (AR), and AR signaling inhibits cell growth in breast tissues. Therefore, the aim of this study was to investigate the potential of MPA to disrupt AR signaling in an ex vivo culture model of normal human breast tissue. Histologically normal breast tissues from women undergoing breast surgical operation were cultured in the presence or in the absence of the native AR ligand 5α-dihydrotestosterone (DHT), MPA, or the AR antagonist bicalutamide. Ki67, bromodeoxyuridine, B-cell CLL/lymphoma 2 (BCL2), AR, estrogen receptor α, and progesterone receptor were detected by immunohistochemistry. DHT inhibited the proliferation of breast epithelial cells in an AR-dependent manner within tissues from postmenopausal women, and MPA significantly antagonized this androgenic effect. These hormonal responses were not commonly observed in cultured tissues from premenopausal women. In tissues from postmenopausal women, DHT either induced or repressed BCL2 expression, and the antiandrogenic effect of MPA on BCL2 was variable. MPA significantly opposed the positive effect of DHT on AR stabilization, but these hormones had no significant effect on estrogen receptor α or progesterone receptor levels. In a subset of postmenopausal women, MPA exerts an antiandrogenic effect on breast epithelial cells that is associated with increased proliferation and destabilization of AR protein. This activity may contribute mechanistically to the increased risk of breast cancer in women taking MPA-containing EPT.

Recovery of tobacco BY-2 cells after high hydrostatic pressure treatment.

PubMed

Kusube, Masataka; Nishino, Takumi; Nishikawa, Yuki; Goto, Masaki; Matsuki, Hitoshi; Iwahashi, Hitoshi

2010-02-01

The recovery of Nicotiana tabacum L. cv. Bright Yellow 2 (BY-2) cells in Linsmaire and Skoog medium after treatment at high hydrostatic pressure was investigated using an Evans Blue staining method to discriminate live from dead cells. The survival of BY-2 cells just after the high-pressure treatment at 5 degrees C and 25 degrees C decreased abruptly at pressures higher than 50 MPa and 100 MPa, respectively. Furthermore, almost all of the BY-2 cells treated at 5 degrees C and 25 degrees C recovered pressures below 25 MPa and 75 MPa, respectively. However, no BY-2 cells recovered at pressures above 100 MPa at either temperature.

Acceptance and Commitment Therapy for the Treatment of Music Performance Anxiety: A Pilot Study with Student Vocalists

PubMed Central

Juncos, David G.; Heinrichs, Glenn A.; Towle, Philip; Duffy, Kiera; Grand, Sebastian M.; Morgan, Matthew C.; Smith, Jonathan D.; Kalkus, Evan

2017-01-01

This study investigated the use of Acceptance and Commitment Therapy (ACT) as a treatment for music performance anxiety (MPA) in an uncontrolled pilot design. ACT is a newer, “third-wave” therapy that differs from previous MPA treatments, because its goal is not to reduce symptoms of MPA. Rather, ACT aims to enhance psychological flexibility in the presence of unwanted symptoms through the promotion of six core processes collectively known as the ACT “Hexaflex.” A small group of student vocalists (N = 7) from an elite choral college were recruited using objective criteria for evaluating MPA. Participants received 12 ACT sessions, and their baseline functioning served as a pre-treatment control. Treatment consisted of an orientation to ACT, identifying experientially avoidant behaviors, facilitation of Hexaflex processes, group performances in which valued behaviors were practiced in front of one another, meditations, homework, and completion of self-report measures before, during, and after treatment (at a 1- and 3-month follow-up). Improvements were observed in participants' cognitive defusion, acceptance of MPA symptoms, and psychological flexibility at post-treatment and follow-ups. Students also appeared to improve their performance quality and reduce their shame over having MPA. These results add to existing research suggesting ACT is a promising intervention for MPA, while also highlighting how vocal students may be less impaired by physical MPA symptoms. PMID:28674509

The geomechanical strength of carbonate rock in Kinta valley, Ipoh, Perak Malaysia

NASA Astrophysics Data System (ADS)

Mazlan, Nur Amanina; Lai, Goh Thian; Razib, Ainul Mardhiyah Mohd; Rafek, Abdul Ghani; Serasa, Ailie Sofyiana; Simon, Norbert; Surip, Noraini; Ern, Lee Khai; Mohamed, Tuan Rusli

2018-04-01

The stability of both cut rocks and underground openings were influenced by the geomechanical strength of rock materials, while the strength characteristics are influenced by both material characteristics and the condition of weathering. This paper present a systematic approach to quantify the rock material strength characteristics for material failure and material & discontinuities failure by using uniaxial compressive strength, point load strength index and Brazilian tensile strength for carbonate rocks. Statistical analysis of the results at 95 percent confidence level showed that the mean value of compressive strength, point load strength index and Brazilian tensile strength for with material failure and material & discontinuities failure were 76.8 ± 4.5 and 41.2 ± 4.1 MPa with standard deviation of 15.2 and 6.5 MPa, respectively. The point load strength index for material failure and material & discontinuities failure were 3.1 ± 0.2 MPa and 1.8 ± 0.3 MPa with standard deviation of 0.9 and 0.6 MPa, respectively. The Brazilian tensile strength with material failure and material & discontinuities failure were 7.1 ± 0.3 MPa and 4.1 ± 0.3 MPa with standard deviation of 1.4 and 0.6 MPa, respectively. The results of this research revealed that the geomechanical strengths of rock material of carbonate rocks for material & discontinuities failure deteriorates approximately ½ from material failure.

Pregnancy Outcomes Related to Mycophenolate Exposure in Female Kidney Transplant Recipients.

PubMed

King, R W; Baca, M J; Armenti, V T; Kaplan, B

2017-01-01

In 2012, the U.S. Food and Drug Administration issued guidelines advising kidney transplant recipients (KTRs) to discontinue mycophenolate (MPA) in preparation for pregnancy. Little is known about how this guidance has affected pregnancy and graft outcomes. The purpose of this retrospective cohort study was to investigate any association between the discontinuation of MPA and KTR pregnancy and graft outcomes. Data from the National Transplantation Pregnancy Registry included 382 cases in which KTRs managed on MPA became pregnant. Overall, 22 variables, including the time in which a KTR discontinued MPA, were assessed across four end points: miscarriages, birth defects, and 2- and 5-year postpartum graft loss. Birth defects and miscarriages were similar among KTRs who discontinued MPA >6 and <6 weeks prior to pregnancy and during the first trimester. In contrast, discontinuing MPA during the second trimester or later significantly increased the risk of miscarriages (odds ratio [OR] 9.35, 95% confidence interval [CI] 4.31-20.00, p < 0.001) and birth defects (OR 6.06, 95% CI 1.96-18.87, p = 0.002). Discontinuing MPA <6 weeks prior to pregnancy was associated with an increased risk of 5-year graft loss. For the fetus, there is value to discontinuing MPA anytime prior to the second trimester. Adhering to current guidelines does not negatively affect graft survival. © Copyright 2016 The American Society of Transplantation and the American Society of Transplant Surgeons.

Acceptance and Commitment Therapy for the Treatment of Music Performance Anxiety: A Pilot Study with Student Vocalists.

PubMed

Juncos, David G; Heinrichs, Glenn A; Towle, Philip; Duffy, Kiera; Grand, Sebastian M; Morgan, Matthew C; Smith, Jonathan D; Kalkus, Evan

2017-01-01

This study investigated the use of Acceptance and Commitment Therapy (ACT) as a treatment for music performance anxiety (MPA) in an uncontrolled pilot design. ACT is a newer, "third-wave" therapy that differs from previous MPA treatments, because its goal is not to reduce symptoms of MPA. Rather, ACT aims to enhance psychological flexibility in the presence of unwanted symptoms through the promotion of six core processes collectively known as the ACT "Hexaflex." A small group of student vocalists ( N = 7) from an elite choral college were recruited using objective criteria for evaluating MPA. Participants received 12 ACT sessions, and their baseline functioning served as a pre-treatment control. Treatment consisted of an orientation to ACT, identifying experientially avoidant behaviors, facilitation of Hexaflex processes, group performances in which valued behaviors were practiced in front of one another, meditations, homework, and completion of self-report measures before, during, and after treatment (at a 1- and 3-month follow-up). Improvements were observed in participants' cognitive defusion, acceptance of MPA symptoms, and psychological flexibility at post-treatment and follow-ups. Students also appeared to improve their performance quality and reduce their shame over having MPA. These results add to existing research suggesting ACT is a promising intervention for MPA, while also highlighting how vocal students may be less impaired by physical MPA symptoms.

Using community-level metrics to monitor the effects of marine protected areas on biodiversity.

PubMed

Soykan, Candan U; Lewison, Rebecca L

2015-06-01

Marine protected areas (MPAs) are used to protect species, communities, and their associated habitats, among other goals. Measuring MPA efficacy can be challenging, however, particularly when considering responses at the community level. We gathered 36 abundance and 14 biomass data sets on fish assemblages and used meta-analysis to evaluate the ability of 22 distinct community diversity metrics to detect differences in community structure between MPAs and nearby control sites. We also considered the effects of 6 covariates-MPA size and age, MPA size and age interaction, latitude, total species richness, and level of protection-on each metric. Some common metrics, such as species richness and Shannon diversity, did not differ consistently between MPA and control sites, whereas other metrics, such as total abundance and biomass, were consistently different across studies. Metric responses derived from the biomass data sets were more consistent than those based on the abundance data sets, suggesting that community-level biomass differs more predictably than abundance between MPA and control sites. Covariate analyses indicated that level of protection, latitude, MPA size, and the interaction between MPA size and age affect metric performance. These results highlight a handful of metrics, several of which are little known, that could be used to meet the increasing demand for community-level indicators of MPA effectiveness. © 2015 Society for Conservation Biology.

Different responses to treatment across classified diseases and severities in Japanese patients with microscopic polyangiitis and granulomatosis with polyangiitis: a nationwide prospective inception cohort study.

PubMed

Sada, Ken-ei; Yamamura, Masahiro; Harigai, Masayoshi; Fujii, Takao; Takasaki, Yoshinari; Amano, Koichi; Fujimoto, Shouichi; Muso, Eri; Murakawa, Yohko; Arimura, Yoshihiro; Makino, Hirofumi

2015-11-02

This study aims to elucidate the prognosis and the effectiveness of current treatments for Japanese patients with microscopic polyangiitis (MPA) and granulomatosis with polyangiitis (GPA). Patients with newly diagnosed MPA and GPA were enrolled in a nationwide, prospective, inception cohort study from 22 tertiary Japanese institutions, and treatment patterns and responses were evaluated for 24 months. Primary outcome measures were rates of remission (Birmingham Vasculitis Activity Score, 0) and remission with low-dose glucocorticoids (GC) (prednisolone ≤ 10 mg) (GC remission). Of 156 enrolled patients, 78 MPA patients and 33 GPA patients were included. Concomitant cyclophosphamide (CY) was used in 24 MPA (31 %) and 20 GPA (60 %) patients during the initial 3 weeks of treatment. After 6 months, remission was achieved in 66 MPA (85 %) and 29 GPA (87 %) patients, while GC remission was obtained in only 31 MPA (40 %) and 13 GPA (39 %) patients. During the 24-month period, 14 MPA patients and 2 GPA patients died; end stage renal disease (ESRD) was noted in 13 MPA patients but no GPA patients. Patients with severe disease, according to the European Vasculitis Study Group (EUVAS) classification, showed poorer ESRD-free and overall survival rates than those with generalized disease (p < 0.0001). There were no differences in relapse-free survival rates between GPA and MPA, among EUVAS-defined disease severity categories, and between anti-neutrophil cytoplasmic antibody subspecialties. The majority of Japanese patients with MPA and GPA received treatment with high-dose GC and limited CY use, and showed high remission and relapse-free survival rates but low GC remission rates in clinical practice. University Hospital Medical Information Network Clinical Trials Registry UMIN000001648 . Registered 28 February 2009.

Plant water use characteristics of five dominant shrub species of the Lower Rio Grande Valley, Texas, USA: implications for shrubland restoration and conservation.

PubMed

Adhikari, Arjun; White, Joseph D

2014-01-01

The biogeographic distribution of plant species is inherently associated with the plasticity of physiological adaptations to environmental variation. For semi-arid shrublands with a legacy of saline soils, characterization of soil water-tolerant shrub species is necessary for habitat restoration given future projection of increased drought magnitude and persistence in these ecosystems. Five dominant native shrub species commonly found in the Lower Rio Grande Valley, TX, USA, were studied, namely Acacia farnesiana, Celtis ehrenbergiana, Forestiera angustifolia, Parkinsonia aculeata and Prosopis glandulosa. To simulate drought conditions, we suspended watering of healthy, greenhouse-grown plants for 4 weeks. Effects of soil salinity were also studied by dosing plants with 10% NaCl solution with suspended watering. For soil water deficit treatment, the soil water potential of P. glandulosa was the highest (-1.20 MPa), followed by A. farnesiana (-4.69 MPa), P. aculeata (-5.39 MPa), F. angustifolia (-6.20 MPa) and C. ehrenbergiana (-10.02 MPa). For the soil salinity treatment, P. glandulosa also had the highest soil water potential value (-1.60 MPa), followed by C. ehrenbergiana (-1.70 MPa), A. farnesiana (-1.84 MPa), P. aculeata (-2.04 MPa) and F. angustifolia (-6.99 MPa). Within the species, only C. ehrenbergiana and F. angustifolia for soil water deficit treatment and A. farnesiana for the salinity treatment had significantly lower soil water potential after 4 weeks of treatment (P < 0.05). We found that soil water potential, stomatal conductance and net photosynthesis of the species significantly reduced over time for both treatments (P < 0.05). We conclude that while all species exhibited capacities to withstand current water availability, some species demonstrated limited tolerance for extreme water stress that may be important for management of future shrub diversity in Lower Rio Grande Valley.

Effects of high pressure application (400 and 900 MPa) and refrigerated storage time on the oxidative stability of sliced skin vacuum packed dry-cured ham.

PubMed

Clariana, Maria; Guerrero, Luis; Sárraga, Carmen; Garcia-Regueiro, José A

2012-02-01

The effect of high pressure processing at 400 MPa and 900 MPa on the oxidative stability of sliced and vacuum packaged commercial dry-cured ham was determined by analyzing the antioxidant enzyme activities, TBARS levels (thiobarbituric acid reactive substances), vitamin E content and physicochemical characteristics during refrigerated storage for 50 days in different light conditions. In dry-cured ham pressurized at 400 MPa color changes and sensory analyses were also assessed. The high pressure process at 900 MPa produced a decrease in superoxide dismutase (SOD) and glutathione peroxidase (GSHPx) activities and increased vitamin E content. In contrast, pressurization at 400 MPa, increased SOD activity, and showed no effect on vitamin E content and GSHPx activity. In general the physicochemical parameters determined (fat, moisture and collagen) were unaffected by pressurization. Treatment at 400 MPa increased the instrumental color measurement of lightness (L* values, CIELAB). This level of pressure also modified the hardness, chewiness, saltiness and color intensity. These changes of the sensory attributes in dry-cured ham were significant, but small. Copyright © 2011 Elsevier Ltd. All rights reserved.

Blueberry polyphenol oxidase: Characterization and the kinetics of thermal and high pressure activation and inactivation.

PubMed

Terefe, Netsanet Shiferaw; Delon, Antoine; Buckow, Roman; Versteeg, Cornelis

2015-12-01

Partially purified blueberry polyphenol oxidase (PPO) in Mcllvaine buffer (pH=3.6, typical pH of blueberry juice) was subjected to processing at isothermal-isobaric conditions at temperatures from 30 to 80 °C and pressure from 0.1 to 700 MPa. High pressure processing at 30-50 °C at all pressures studied caused irreversible PPO activity increase with a maximum of 6.1 fold increase at 500 MPa and 30 °C. Treatments at mild pressure-mild temperature conditions (0.1-400 MPa, 60 °C) also caused up to 3 fold PPO activity increase. Initial activity increase followed by a decrease occurred at relatively high pressure-mild temperature (400-600 MPa, 60 °C) and mild pressure-high temperature (0.1-400 MPa, 70-80 °C) combinations. At temperatures higher than 76 °C, monotonic decrease in PPO activity occurred at 0.1 MPa and pressures higher than 500 MPa. The activation/inactivation kinetics of the enzyme was successfully modelled assuming consecutive reactions in series with activation followed by inactivation. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Medroxyprogesterone acetate-treated human, primary endometrial epithelial cells reveal unique gene expression signature linked to innate immunity and HIV-1 susceptibility.

PubMed

Woods, Matthew W; Zahoor, Muhammad Atif; Dizzell, Sara; Verschoor, Chris P; Kaushic, Charu

2018-01-01

Medroxyprogesterone acetate (MPA), a progestin-based hormonal contraceptive designed to mimic progesterone, has been linked to increased human immunodeficiency virus (HIV-1) susceptibility. Genital epithelial cells (GECs) form the mucosal lining of the female genital tract (FGT) and provide the first line of protection against HIV-1. The impact of endogenous sex hormones or MPA on the gene expression profile of GECs has not been comprehensively documented. Using microarray analysis, we characterized the transcriptional profile of primary endometrial epithelial cells grown in physiological levels of E2, P4, and MPA. Each hormone treatment altered the gene expression profile of GECs in a unique manner. Interestingly, although MPA is a progestogen, the gene expression profile induced by it was distinct from P4. MPA increased gene expression of genes related to inflammation and cholesterol synthesis linked to innate immunity and HIV-1 susceptibility. The analysis of gene expression profiles provides insights into the effects of sex hormones and MPA on GECs and allows us to posit possible mechanisms of the MPA-mediated increase in HIV-1 acquisition. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Cytotoxic effect of commercially available methylprednisolone acetate with and without reduced preservatives on dorsal root ganglion sensory neurons in rats.

PubMed

Knezevic, Nebojsa Nick; Candido, Kenneth D; Cokic, Ivan; Krbanjevic, Aleksandar; Berth, Sarah L; Knezevic, Ivana

2014-01-01

Epidural and intrathecal injections of methylprednisolone acetate (MPA) have become the most commonly performed interventional procedures in the United States and worldwide in the last 2 decades. However neuraxial MPA injection has been dogged by controversy regarding the presence of different additives used in commercially prepared glucocorticoids. We previously showed that MPA could be rendered 85% free of polyethylene glycol (PEG) by a simple physical separation of elements in the suspension. The objective of the present study was to explore a possible cytotoxic effect of commercially available MPA (with intact or reduced preservatives) on rat sensory neurons. We exposed primary dissociated rat dorsal root ganglia (DRG) sensory neurons to commercially available MPA for 24 hours with either the standard (commercial) concentration of preservatives or to different fractions following separation (MPA suspension whose preservative concentration had been reduced, or fractions containing higher concentrations of preservatives). Cells were stained with the TUNEL assay kit to detect apoptotic cells and images were taken on the Bio-Rad Laser Sharp-2000 system. We also detected expression of caspase-3, as an indicator of apoptosis in cell lysates. We exposed sensory neurons from rat DRG to different concentrations of MPA from the original commercially prepared vial. TUNEL assay showed dose-related responses and increased percentages of apoptotic cells with increasing concentrations of MPA. Increased concentrations of MPA caused 1.5 - 2 times higher caspase-3 expression in DRG sensory neurons than in control cells (ANOVA, P = 0.001). Our results showed that MPA with reduced preservatives caused significantly less apoptosis observed with TUNEL assay labeling (P < 0.001) and caspase-3 immunoblotting (P = 0.001) than in neurons exposed to MPA from a commercially prepared vial or "clear phase" that contained higher concentrations of preservatives. Even though MPA with reduced preservatives caused 12.5% more apoptosis in DRG sensory neurons than in control cells, post hoc analysis showed no differences between these 2 groups. Our data was collected from in vitro isolated rat DRG neurons. There is a possibility that in vivo neurons have different extents of vulnerability compared to isolated neurons. Results of the present study identified a cytotoxic effect of commercially available MPA with preservatives or with a "clear phase" containing higher concentrations of preservatives on primary isolated rat DRG sensory neurons. This was shown by TUNEL positive assay and by increased caspase-3 expression as one of the final executing steps in apoptotic pathways in DRG neurons. However, our results showed no statistically significant difference between the control cells (saline-treated) and cells treated with MPA with reduced concentrations of preservatives, pointing out that either PEG or myristylgamma-picolinium chloride (MGPC) or their combination have harmful effects on these cells. Reduction of concentrations of preservatives from commercially available MPA suspensions by using the simple method of inverting vials for 2 hours could be considered useful in clinical practice to enhance the safety of this depot steroid when injected neuraxially.

Effect of Shock Loading on Rock Properties and in situ States.

DTIC Science & Technology

1980-06-01

site to contain a nuclear event, con- siderable effort was spent in obtaining the stresses, via the overcore technique and hydraulic fracturing . The...Dining Car region indicated, via hydraulic fracturing , a minimum in situ stress of about 3.8 MPa and via the overcore technique, approximately 2.8 MPa...decreased to about 1.2 MPa, as compared to a pre-Dining Car stress of 3-3.5 MPa. These measurements were obtained via a combina- tion of hydraulic

Hormone replacement therapy in women with epilepsy: a randomized, double-blind, placebo-controlled study.

PubMed

Harden, Cynthia L; Herzog, Andrew G; Nikolov, Blagovest G; Koppel, Barbara S; Christos, Paul J; Fowler, Kristen; Labar, Douglas R; Hauser, W Allen

2006-09-01

Previous reports have suggested that hormone replacement therapy (HRT) could increase seizure activity in women with epilepsy. We sought to determine whether adding HRT to the medication regimen of postmenopausal women with epilepsy was associated with an increase in seizure frequency. This was a randomized, double-blind, placebo-controlled trial of the effect of HRT on seizure frequency in postmenopausal women with epilepsy, taking stable doses of antiepileptic drugs (AEDs), and within 10 years of their last menses. After a 3-month prospective baseline, subjects were randomized to placebo, Prempro (0.625 mg of conjugated equine estrogens plus 2.5 mg of medroxyprogesterone acetate or CEE/MPA) daily, or double-dose CEE/MPA daily for a 3-month treatment period. Twenty-one subjects were randomized after completing baseline. The subjects' ages ranged from 45 to 62 years (mean, 53 years; SD, +/-5), and the number of AEDs used ranged from none to three (median, one). Five (71%) of seven subjects taking double-dose CEE/MPA had a worsening seizure frequency of at least one seizure type, compared with four (50%) of eight taking single-dose CEE/MPA and one (17%) of six taking placebo (p = 0.05). An increase in seizure frequency of the subject's most severe seizure type was associated with increasing CEE/MPA dose (p = 0.008). An increase in complex partial seizure frequency also was associated with increasing CEE/MPA dose (p = 0.05). Two subjects taking lamotrigine had a decrease in lamotrigine levels of 25-30% while taking CEE/MPA. CEE/MPA is associated with a dose-related increase in seizure frequency in postmenopausal women with epilepsy. CEE/MPA may decrease lamotrigine levels.

Microtensile bond strength analysis of different adhesive systems and dentin prepared with high-speed and Er:YAG laser: a comparative study.

PubMed

Oliveira, Denise Cerqueira; Manhães, Lussara Azevedo; Marques, Márcia Martins; Matos, Adriana Bona

2005-04-01

The aim of this study was to evaluate the bond strength of two adhesive systems (Single Bond and Clearfil SE Bond) subjected or not to a thermocycling procedure and applied to cavities prepared either with high-speed diamond bur or Er:YAG laser. One of the possible applications of dental lasers includes increasing the quality of bond strength. This in vitro study was carried out using a microtensile test on 16 bovine teeth, divided into eight groups. Cavities were prepared on superficial dentin of the medium portion of the buccal surface. After application of adhesive systems, composite restorations were performed at 5-mm height. After 24 h, four groups of teeth were immersed in water, and the other four were thermocycled. Bonded specimens were sectioned into serial 1x1-mm beams, which were subjected to a microtensile test. Final values of bond strength were measured, expressed in MPa, and statistically analyzed. Results were as follows: G1 (26.281 +/- 5.454 MPa); G2 (10.965 +/- 3.714 MPa); G3 (18.549 +/- 6.113 MPa); G4 (14.295 +/- 3.806 MPa); G5 (18.225 +/- 5.701 MPa); G6 (5.588 +/- 2.211 MPa); G7 (18.256 +/- 3.819 MPa); and G8 (15.423 +/- 4.714 MPa). Self-etching adhesive system (SE) produced more stable bond strength results than the system that indicates total etching (SB). For dentin prepared at high speed, the total etching adhesive system was more indicated, whereas Er:YAG laser-preparation dentin was not influenced by the adhesive system. The thermocycling procedure could negatively affect microtensile bond strength of both adhesive systems, being more deleterious to SB than to SE.

Polymerization contraction stress in light-cured compomer restorative materials.

PubMed

Chen, H Y; Manhart, J; Kunzelmann, K-H; Hickel, R

2003-11-01

The magnitude and kinetics of polymerization contraction stress build-up may be potential predictors of bond failure of adhesive restorations. The present study determined these properties of seven commercial compomers (Dyract, Dyract AP, F2000 Rasant, Hytac, Compoglass F, Luxat, Glasiosite). Polymerization shrinkage was generated by 40 s light curing the test materials (800 mW/cm2). The contraction force induced was recorded for 300 s at room temperature (23-24 degrees C) by means of a Stress-Strain-Analyzer (C factor=0.33). Maximum contraction stress (MPa), coefficient of near linear fit of contraction force/time (gradient) and relative force rate (%/s) of each material were compared with that of two hybrid composites (Tetric Ceram, Prodigy). The statistical analysis was conducted by ANOVA (alpha=0.05) and post hoc Tukey's test. No statistically significant differences in the maximum stress between Glasiosite (2.27+/-0.06 MPa), Hytac (2.31+/-0.07 MPa) and Tetric Ceram (2.21+/-0.11 MPa), and between Compoglass F (2.60+/-0.18 MPa) and Prodigy (2.70+/-0.06 MPa) were found. The contraction stress of F2000 Rasant (3.41+/-0.09 MPa) and Luxat (3.33+/-0.08 MPa) were significantly highest, whilst Dyract exhibited the significantly lowest shrinkage stress (1.27+/-0.08 MPa) among the tested materials. High contraction stress, early start of stress build-up and rapid contraction force development may lead to failure of bond to tooth structure. This study suggested that the contraction stress and kinetic behavior of compomers are generally similar to those of hybrid composites in a dry condition. Dyract might be superior in maintaining the bond with cavity walls compared to conventional hybrid composites in view of its low shrinkage stress.

Establishment of primary cultures for mouse ameloblasts as a model of their lifetime

DOE Office of Scientific and Technical Information (OSTI.GOV)

Suzawa, Tetsuo; Itoh, Nao; Department of Clinical Pharmacy, School of Pharmaceutical Science, Showa University

2006-07-07

To understand how the properties of ameloblasts are spatiotemporally regulated during amelogenesis, two primary cultures of ameloblasts in different stages of differentiation were established from mouse enamel epithelium. Mouse primary ameloblasts (MPAs) prepared from immature enamel epithelium (MPA-I) could proliferate, whereas those from mature enamel epithelium (MPA-M) could not. MPA-M but not MPA-I caused apoptosis during culture. The mRNA expression of amelogenin, a marker of immature ameloblasts, was down-regulated, and that of enamel matrix serine proteiase-1, a marker of mature ameloblasts, was induced in MPA-I during culture. Using green fluorescence protein as a reporter, a visualized reporter system was establishedmore » to analyze the promoter activity of the amelogenin gene. The region between -1102 bp and -261 bp was required for the reporter expression in MPA-I. These results suggest that MPAs are valuable in vitro models for investigation of ameloblast biology, and that the visualized system is useful for promoter analysis in MPAs.« less

Fracture of fiber-reinforced composites analyzed via acoustic emission.

PubMed

Ereifej, Nadia S; Oweis, Yara G; Altarawneh, Sandra K

2015-01-01

This study investigated the fracture resistance of composite resins using a three-point bending test and acoustic emission (AE) analysis. Three groups of specimens (n=15) were prepared: non-reinforced BelleGlass HP composite (NRC), unidirectional (UFRC) and multidirectional (MFRC) fiber-reinforced groups which respectively incorporated unidirectional Stick and multidirectional StickNet fibers. Specimens were loaded to failure in a universal testing machine while an AE system was used to detect audible signals. Initial fracture strengths and AE amplitudes were significantly lower than those at final fracture in all groups (p<0.05). Initial fracture strength of UFRC (170.0 MPa) was significantly higher than MFRC (124.6 MPa) and NRC (87.9 MPa). Final fracture strength of UFRC (198.1 MPa) was also significantly higher than MFRC (151.0 MPa) and NRC (109.2 MPa). Initial and final fracture strengths were significantly correlated (r=0.971). It was concluded that fiber reinforcement improved the fracture resistance of composite resin materials and the monitoring of acoustic signals revealed significant information regarding the fracture process.

Effects of pressure and temperature on the survival rate of adherent A-172 cells

NASA Astrophysics Data System (ADS)

Yasuhara, Ryo; Kushida, Ryo; Ishii, Shiwori; Yamanoha, Banri; Shimizu, Akio

2013-06-01

Preservation of cells under high pressure is an important alternative to cryopreservation. We studied the effect of temperature (4, 25, 37°C) and pressure (0.1-350 MPa) on the survival rate of A-172 glioblastoma cells. The survival rate was not changed by brief (10 min) pressurization of up to 150 MPa, but the survival rate began to decrease from 150 MPa, and most of the A-172 cells died when treated with over 200 MPa. Lengthy pressurization (4 days) at lower pressure (upto 20.1 MPa) without medium exchange showed complex results. The survival rate of cells preserved at 25°C showed two maxima at 1.6 and 20.1 MPa. After preservation, cells adhered and proliferated in the same way as normal cells when cultured at 37°C in a CO2 incubator. The other two temperatures, 4° and 37°C, showed no maximum survival rate. Therefore, a high survival rate can be maintained with high pressure treatment.

Acoustic telemetry and network analysis reveal the space use of multiple reef predators and enhance marine protected area design

PubMed Central

Lea, James S. E.; Humphries, Nicolas E.; von Brandis, Rainer G.; Clarke, Christopher R.; Sims, David W.

2016-01-01

Marine protected areas (MPAs) are commonly employed to protect ecosystems from threats like overfishing. Ideally, MPA design should incorporate movement data from multiple target species to ensure sufficient habitat is protected. We used long-term acoustic telemetry and network analysis to determine the fine-scale space use of five shark and one turtle species at a remote atoll in the Seychelles, Indian Ocean, and evaluate the efficacy of a proposed MPA. Results revealed strong, species-specific habitat use in both sharks and turtles, with corresponding variation in MPA use. Defining the MPA's boundary from the edge of the reef flat at low tide instead of the beach at high tide (the current best in Seychelles) significantly increased the MPA's coverage of predator movements by an average of 34%. Informed by these results, the larger MPA was adopted by the Seychelles government, demonstrating how telemetry data can improve shark spatial conservation by affecting policy directly. PMID:27412274

Structural Insights on the Mycobacterium tuberculosis Proteasomal ATPase Mpa

PubMed Central

Wang, Tao; Li, Hua; Lin, Gang; Tang, Chunyan; Li, Dongyang; Nathan, Carl; Darwin, K. Heran; Li, Huilin

2009-01-01

Summary Proteasome-mediated protein turnover in all domains of life is an energy-dependent process that requires ATPase activity. Mycobacterium tuberculosis (Mtb) was recently shown to possess a ubiquitin-like proteasome pathway that plays an essential role in Mtb resistance to killing by products of host macrophages. Here we report our structural and biochemical investigation of Mpa, the presumptive Mtb proteasomal ATPase. We demonstrate that Mpa binds to the Mtb proteasome in the presence of ATPγS, providing the physical evidence that Mpa is the proteasomal ATPase. X-ray crystallographic determination of the conserved inter-domain showed a five-stranded double β-barrel structure containing a Greek key motif. The structure and mutagenesis indicate a major role of the inter-domain for Mpa hexamerization. Our mutational and functional studies further suggest that the central channel in the Mpa hexamer is involved in protein substrate translocation and degradation. These studies provide insights into how a bacterial proteasomal ATPase interacts with and facilitates protein degradation by the proteasome. PMID:19836337

Biomechanical analysis of wrapping of the moderately dilated ascending aorta.

PubMed

Plonek, Tomasz; Rylski, Bartosz; Dumanski, Andrzej; Siedlaczek, Przemyslaw; Kustrzycki, Wojciech

2015-08-01

External wrapping is a surgical method performed to prevent the dilatation of the aorta and to decrease the risk of its dissection and rupture. However, it is also believed to cause degeneration of the aortic wall. A biomechanical analysis was thus performed to assess the stress of the aortic wall subjected to external wrapping. A stress analysis using the finite elements method was carried out on three models: a non-dilated aorta, a moderately dilated aorta and a wrapped aorta. The models were subjected to a pulsatile flow (120/80 mmHg) and a systolic aortic annulus motion of 11 mm. The finite elements analysis showed that the stress exerted on the outer surface of the ascending aorta in the wrapping model (0.05-0.8 MPa) was similar to that observed in the normal aorta (0.03-0.7 MPa) and was lower than in the model of a moderately dilated aorta (0.06-1.4 MPa). The stress on the inner surface of the ascending aorta ranged from 0.2 MPa to 0.4 MPa in the model of the normal aorta, from 0.3 to 1.3 MPa in the model of the dilated aorta and from 0.05 MPa to 0.4 MPa in the wrapping model. The results of this study suggest that the aortic wall is subjected to similar stress following a wrapping procedure to the one present in the normal aorta.

Use of long-distance migration patterns of an endangered species to inform conservation planning for the world's largest marine protected area.

PubMed

Hays, Graeme C; Mortimer, Jeanne A; Ierodiaconou, Daniel; Esteban, Nicole

2014-12-01

Large marine protected areas (MPAs), each hundreds of thousands of square kilometers, have been set up by governments around the world over the last decade as part of efforts to reduce ocean biodiversity declines, yet their efficacy is hotly debated. The Chagos Archipelago MPA (640,000 km(2) ) (Indian Ocean) lies at the heart of this debate. We conducted the first satellite tracking of a migratory species, the green turtle (Chelonia mydas), within the MPA and assessed the species' use of protected versus unprotected areas. We developed an approach to estimate length of residence within the MPA that may have utility across migratory taxa including tuna and sharks. We recorded the longest ever published migration for an adult cheloniid turtle (3979 km). Seven of 8 tracked individuals migrated to distant foraging grounds, often ≥1000 km outside the MPA. One turtle traveled to foraging grounds within the MPA. Thus, networks of small MPAs, developed synergistically with larger MPAs, may increase the amount of time migrating species spend within protected areas. The MPA will protect turtles during the breeding season and will protect some turtles on their foraging grounds within the MPA and others during the first part of their long-distance postbreeding oceanic migrations. International cooperation will be needed to develop the network of small MPAs needed to supplement the Chagos Archipelago MPA. © 2014 Society for Conservation Biology.

Hyperventilation in anticipatory music performance anxiety.

PubMed

Studer, Regina Katharina; Danuser, Brigitta; Hildebrandt, Horst; Arial, Marc; Wild, Pascal; Gomez, Patrick

2012-09-01

Self-report studies have shown an association between music performance anxiety (MPA) and hyperventilation complaints. However, hyperventilation was never assessed physiologically in MPA. This study investigated the self-reported affective experience, self-reported physiological symptoms, and cardiorespiratory variables including partial pressure of end-tidal CO(2) (Petco(2)), which is an indicator for hyperventilation, in 67 music students before a private and a public performance. The response coherence between these response domains was also investigated. From the private to the public session, the intensity of all self-report variables increased (all p values < .001). As predicted, the higher the musician's usual MPA level, the larger were these increases (p values < .10). With the exception of Petco(2), the main cardiorespiratory variables also increased from the private to the public session (p values < .05). These increases were not modulated by the usual MPA level (p values > .10). Petco(2) showed a unique response pattern reflected by an MPA-by-session interaction (p < .01): it increased from the private to the public session for musicians with low MPA levels and decreased for musicians with high MPA levels. Self-reported physiological symptoms were related to the self-reported affective experience (p values < .05) rather than to physiological measures (p values > .17). These findings show for the first time how respiration is stimulated before a public performance in music students with different MPA levels. The hypothesis of a hyperventilation tendency in high-performance-anxious musicians is supported. The response coherence between physiological symptoms and physiological activation is weak.

Comparing Presenting Clinical Features in 48 Children With Microscopic Polyangiitis to 183 Children Who Have Granulomatosis With Polyangiitis (Wegener's): An ARChiVe Cohort Study.

PubMed

Cabral, David A; Canter, Debra L; Muscal, Eyal; Nanda, Kabita; Wahezi, Dawn M; Spalding, Steven J; Twilt, Marinka; Benseler, Susanne M; Campillo, Sarah; Charuvanij, Sirirat; Dancey, Paul; Eberhard, Barbara A; Elder, Melissa E; Hersh, Aimee; Higgins, Gloria C; Huber, Adam M; Khubchandani, Raju; Kim, Susan; Klein-Gitelman, Marisa; Kostik, Mikhail M; Lawson, Erica F; Lee, Tzielan; Lubieniecka, Joanna M; McCurdy, Deborah; Moorthy, Lakshmi N; Morishita, Kimberly A; Nielsen, Susan M; O'Neil, Kathleen M; Reiff, Andreas; Ristic, Goran; Robinson, Angela B; Sarmiento, Angelyne; Shenoi, Susan; Toth, Mary B; Van Mater, Heather A; Wagner-Weiner, Linda; Weiss, Jennifer E; White, Andrew J; Yeung, Rae S M

2016-10-01

To uniquely classify children with microscopic polyangiitis (MPA), to describe their demographic characteristics, presenting clinical features, and initial treatments in comparison to patients with granulomatosis with polyangiitis (Wegener's) (GPA). The European Medicines Agency (EMA) classification algorithm was applied by computation to categorical data from patients recruited to the ARChiVe (A Registry for Childhood Vasculitis: e-entry) cohort, with the data censored to November 2015. The EMA algorithm was used to uniquely distinguish children with MPA from children with GPA, whose diagnoses had been classified according to both adult- and pediatric-specific criteria. Descriptive statistics were used for comparisons. In total, 231 of 440 patients (64% female) fulfilled the classification criteria for either MPA (n = 48) or GPA (n = 183). The median time to diagnosis was 1.6 months in the MPA group and 2.1 months in the GPA group (ranging to 39 and 73 months, respectively). Patients with MPA were significantly younger than those with GPA (median age 11 years versus 14 years). Constitutional features were equally common between the groups. In patients with MPA compared to those with GPA, pulmonary manifestations were less frequent (44% versus 74%) and less severe (primarily, hemorrhage, requirement for supplemental oxygen, and pulmonary failure). Renal pathologic features were frequently found in both groups (75% of patients with MPA versus 83% of patients with GPA) but tended toward greater severity in those with MPA (primarily, nephrotic-range proteinuria, requirement for dialysis, and end-stage renal disease). Airway/eye involvement was absent among patients with MPA, because these GPA-defining features preclude a diagnosis of MPA within the EMA algorithm. Similar proportions of patients with MPA and those with GPA received combination therapy with corticosteroids plus cyclophosphamide (69% and 78%, respectively) or both drugs in combination with plasmapheresis (19% and 22%, respectively). Other treatments administered, ranging in decreasing frequency from 13% to 3%, were rituximab, methotrexate, azathioprine, and mycophenolate mofetil. Younger age at disease onset and, perhaps, both gastrointestinal manifestations and more severe kidney disease seem to characterize the clinical profile in children with MPA compared to those with GPA. Delay in diagnosis suggests that recognition of these systemic vasculitides is suboptimal. Compared with adults, initial treatment regimens in children were comparable, but the complete reversal of female-to-male disease prevalence ratios is a provocative finding. © 2016, American College of Rheumatology.

[Effect of thermal cycling on the composite- composite repair bond strength].

PubMed

Liu, Chang; Lin, Fei; Yue, Lin

2015-08-01

To evaluate the effect of aging of the composite and the adhesive interface on composite-composite repair bond strength. Methacrylate-based composite resin (Clearfil AP-X, composite A) and silorane-based composite resin (Filtek P90, composite B) and their corresponding adhesive, Clearfil SE Bond (adhesive a) and Filtek P90 System Adhesive (adhesive b), were selected in this study. Twenty-four substrates were prepared from composite A or B separately and divided into three groups, each group had 8 substrates: group one, new composites were adhered to the substrates with the use of adhesive a or b, followed by cutting the blocks into sticks; group two, new composites were adhered to the substrates using adhesive a or b, followed by cutting into sticks and thermal cycling; group three, substrates were thermocycled, then polished and adhered new composites using adhesive a or b, followed by cutting into sticks. Each group had 8 combinations of substrate(A, B)-adhesive(a, b)-repair composite (A, B). Fifteen sticks without flaws in each combination of 3 groups were selected utilizing stereomicroscope. The data were analyzed by independent samples t test. In group two, the microtensile strength(MS) of combinations using adhesive a and composite A or B to repair [A-a-A: (45.0 ± 3.2) MPa, B-a-A: (41.7 ± 3.3) MPa, A-a-B: (28.6 ± 3.9) MPa, B-a-B: (47.7 ± 6.6) MPa], and using adhesive b and composite A to repair [A-b-A: (44.2 ± 4.7) MPa, B-b-A: (38.0 ± 3.2) MPa] decreased significantly compared with corresponding combinations in group 1[A-a-A: (70.7 ± 5.5) MPa, B-a-A: (60.3 ± 5.1) MPa, A-a-B: (44.2 ± 1.6) MPa, B-a-B: (54.1 ± 3.2) MPa, A-b-A: (65.6 ± 7.2) MPa, B-b-A: (59.1 ± 4.1) MPa] (P<0.05). However, there was no significant difference between the MS of combinations using adhesive b and composite B to repair in group one and the MS of combinations in group two (P>0.05). The MS of all combinations in group three decreased significantly (P<0.05). Aging of the composite and the adhesive interface might affect the composite-composite repair bond strength.

Capstone Experiences in Small MPA Programs in the United States

ERIC Educational Resources Information Center

Kim, Younhee

2017-01-01

A capstone experience, as an exit degree requirement, allows Master of Public Administration (MPA) students to build quasi-experimental practices by applying learned knowledge and skills throughout their curriculum in the United States. Accredited MPA programs have implemented their capstone courses differently to achieve required standards. Small…

Teaching Stage Fright? -- Implications for Music Educators

ERIC Educational Resources Information Center

Patston, Tim

2014-01-01

Music performance anxiety (MPA) is a widely acknowledged condition in the field of music performance. However, MPA is rarely discussed in the field of music education. Classroom, studio and conservatoire teachers observe their students experiencing MPA related to performances, examinations or auditions, but few have the prerequisite skills to…

Prescription of medroxyprogesterone acetate to a patient with pedophilia, resulting in Cushing's syndrome and adrenal insufficiency.

PubMed

Krueger, Richard B; Hembree, Wylie; Hill, Michael

2006-04-01

This article provides a case report of a patient with pedophilia who was treated over a 4-year period with medroxyprogesterone acetate (MPA) at a dose of 300 mg/day and as a consequence developed Cushing's Syndrome and adrenal insufficiency, for which he was treated and from which he recovered. He also reported a hypersexual reaction to his own past cessation of MPA. Gonadotropin-releasing hormone agonists, which have a more benign side-effect profile than MPA, are suggested as an alternative to MPA.

Correlation between physical anomaly and behavioral abnormalities in Down syndrome

PubMed Central

Bhattacharyya, Ranjan; Sanyal, Debasish; Roy, Krishna; Bhattacharyya, Sumita

2010-01-01

Objective: The minor physical anomaly (MPA) is believed to reflect abnormal development of the CNS. The aim is to find incidence of MPA and its behavioral correlates in Down syndrome and to compare these findings with the other causes of intellectual disability and normal population. Materials and Methods: One-hundred and forty intellectually disabled people attending a tertiary care set-up and from various NGOs are included in the study. The age-matched group from normal population was also studied for comparison. MPA are assessed by using Modified Waldrop scale and behavioral abnormality by Diagnostic assessment scale for severely handicapped (DASH II scale). Results: The Down syndrome group had significantly more MPA than other two groups and most of the MPA is situated in the global head region. There is strong correlation (P < 0.001) between the various grouped items of Modified Waldrop scale. Depression subscale is correlated with anomalies in the hands (P < 0.001), feet and Waldrop total items (P < 0.005). Mania item of DASH II scale is related with anomalies around the eyes (P < 0.001). Self-injurious behavior and total Waldrop score is negatively correlated with global head. Conclusion: Down syndrome group has significantly more MPA and a pattern of correlation between MPA and behavioral abnormalities exists which necessitates a large-scale study. PMID:21559153

Psychological intervention reduces self-reported performance anxiety in high school music students

PubMed Central

Braden, Alice M.; Osborne, Margaret S.; Wilson, Sarah J.

2015-01-01

Music performance anxiety (MPA) can be distressing for many young people studying music, and may negatively impact upon their ability to cope with the demands and stressors of music education. It can also lead young people to give up music or to develop unhealthy coping habits in their adult music careers. Minimal research has examined the effectiveness of psychological programs to address MPA in young musicians. Sixty-two adolescents were pseudo-randomized to a cognitive behavioral (CB) group-delivered intervention or a waitlist condition. The intervention consisted of psychoeducation, cognitive restructuring and relaxation techniques, identification of strengths, goal-setting, imagery and visualization techniques to support three solo performances in front of judges. Significant reductions in self-rated MPA were found in both groups following the intervention and compared to their baseline MPA. This reduction was maintained at 2-months follow-up. There appeared to be inconsistent effects of the intervention upon judge-rated MPA, however the presence of floor effects precluded meaningful reductions in MPA. There appeared to be no effect of the intervention upon judge-rated performance quality. This study highlights the potential for group-based CB programs to be delivered within school music curricula to help young musicians develop skills to overcome the often debilitating effects of MPA. PMID:25784885

Facial Recognition of Happiness Is Impaired in Musicians with High Music Performance Anxiety.

PubMed

Sabino, Alini Daniéli Viana; Camargo, Cristielli M; Chagas, Marcos Hortes N; Osório, Flávia L

2018-01-01

Music performance anxiety (MPA) can be defined as a lasting and intense apprehension connected with musical performance in public. Studies suggest that MPA can be regarded as a subtype of social anxiety. Since individuals with social anxiety have deficits in the recognition of facial emotion, we hypothesized that musicians with high levels of MPA would share similar impairments. The aim of this study was to compare parameters of facial emotion recognition (FER) between musicians with high and low MPA. 150 amateur and professional musicians with different musical backgrounds were assessed in respect to their level of MPA and completed a dynamic FER task. The outcomes investigated were accuracy, response time, emotional intensity, and response bias. Musicians with high MPA were less accurate in the recognition of happiness ( p  = 0.04; d  = 0.34), had increased response bias toward fear ( p  = 0.03), and increased response time to facial emotions as a whole ( p  = 0.02; d  = 0.39). Musicians with high MPA displayed FER deficits that were independent of general anxiety levels and possibly of general cognitive capacity. These deficits may favor the maintenance and exacerbation of experiences of anxiety during public performance, since cues of approval, satisfaction, and encouragement are not adequately recognized.

Final report on APMP.M.P-S3: Results of the supplementary comparison in gas media in the range 1.77 MPa to 6.8 MPa

NASA Astrophysics Data System (ADS)

Owen, N.; Bergoglio, M.

2013-01-01

This report provides the results of the supplementary bilateral comparison APMP.M.P-S3 between NMI Australia (NMIA) and INRIM, Italy executed from November 2010 to November 2011. NMIA acted as the pilot laboratory and provided a Ruska G series piston gauge as the transfer standard, with a nominal area 16.8 mm2 requiring a nominal load of 12 kg to balance a pressure of 7.0 MPa. The purpose of this supplementary bilateral comparison was to provide data for linking NMIA to CCM.P-K1.c in the pressure range greater than 4 MPa to extend the range covered by key comparison APMP.M.P-K1c. The original protocol called for the pressure range from 80 kPa to 6.80 MPa. Both participants agreed to limit this comparison range to 1.77 MPa to 6.50 MPa. Main text. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the APMP, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Psychrometric measurement of soil water potential: Stability of calibration and test of pressure-plate samples

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jones, T.L.; Gee, G.W.; Heller, P.R.

1990-08-01

A commercially available thermocouple psychrometer sample changer (Decagon SC-10A) was used to measure the water potential of field soils ranging in texture from sand to silty clay loam over a range of {minus}0.5 to {minus}20.0 MPa. The standard error of prediction based on regression statistics was generally between 0.04 and 0.14 MPa at {minus}5 MPa. Replacing the measuring junction of the unit changed the calibration slightly; however, it did not significantly alter measurement accuracy. Calibration curves measured throughout a year of testing are consistent and indicate no systematic drift in calibration. Most measurement uncertainty is produced by shifts in themore » intercept in the calibration equation rather than the slope. Both the variability in intercept and the regression error seem to be random. Measurements taken with the SC-10A show that water potential in both sand and silt loam samples removed from 1.5-MPa pressure plates was often 0.5 to 1.0 MPa greater than the 1.5-MPa applied pressure. Limited data from 0.5-MPa pressure plates show close agreement between SC-10A measurements and pressure applied to these more permeable plates.« less

The volumetric fraction of inorganic particles and the flexural strength of composites for posterior teeth.

PubMed

Adabo, Gelson Luis; dos Santos Cruz, Carlos Alberto; Fonseca, Renata Garcia; Vaz, Luís Geraldo

2003-07-01

To evaluate the content of inorganic particles and the flexural strength of new condensable composites for posterior teeth in comparison to hybrid conventional composites. The determination of the content of inorganic particles was performed by mass weighing of a polymerized composite before and after the elimination of the organic phase. The volumetric particle content was determined by a practical method based on Archimedes' principle, which calculates the volume of the composite and their particles by differential mass measured in the air and in water. The flexural strength of three points was evaluated according to the norm ISO 4049:1988. The results showed the following filler content: Alert, 67.26%; Z-100, 65.27%; Filtek P 60, 62.34%; Ariston pHc, 64.07%; Tetric Ceram, 57.22%; Definite, 54.42%; Solitaire, 47.76%. In the flexural strength test, the materials presented the following decreasing order of resistance: Filtek P 60 (170.02 MPa)>Z-100 (151.34 MPa)>Tetric Ceram (126.14 MPa)=Alert (124.89 MPa)>Ariston pHc (102.00 MPa)=Definite (93.63 MPa)>Solitaire (56.71 MPa). New condensable composites for posterior teeth present a concentration of inorganic particles similar to those of hybrid composites but do not necessarily present higher flexural strength.

Measurement of the ( p, , T) Properties for Pure Hydrocarbons at Temperatures up to 600 K and Pressures up to 200 MPa

NASA Astrophysics Data System (ADS)

Ito, T.; Nagata, Y.; Miyamoto, H.

2014-10-01

The data available for the thermodynamic properties of propane, -butane, and isobutane at temperatures above 440 K are outdated and show significant discrepancies with each other. The ambiguity associated with these data could be limiting to the development of any understanding related to the effects of mixing of these substances with other materials such as , ammonia, and non-flammable or lower-flammable HFC refrigerants. In this study, the ( p, , T) properties of propane, -butane, and isobutane were measured at temperatures ranging from (360 to 600) K and pressures ranging from (50 to 200) MPa. Precise measurements were carried out using a metal-bellows variable volumometer with a thermostatted air bath. The expanded uncertainties in the temperature, pressure, and density measurements were estimated to be 5 mK, 0.02 MPa, and 0.88 kg m ( K, MPa), 0.76 kg ( K, MPa), 0.76 kg ( K, MPa), and 2.94 kg ( K, MPa), respectively. The data obtained throughout this study were systematically compared with the calculated values derived from the available equations of state. These models agree well with the measured data at higher temperatures up to 600 K, demonstrating their suitability for an effective and precise examination of the mixing effects of potential alternative mixtures.

The Influence of Phenocrysts on Magma Degassing in Rhyolitic Systems

NASA Astrophysics Data System (ADS)

deGraffenried, R.; Larsen, J. F.; Lindoo, A. N.

2016-12-01

The kinetics of volatile exsolution and magma degassing control volcanic eruption styles, but the role of phenocrysts in the degassing process is poorly understood. The focus of this study is two series of decompression experiments examining how phenocrysts may or may not influence vesicle structures leading to permeability development and degassing in magmas with rhyolitic matrix melts. Powdered rhyolite obsidian (75 SiO2 wt. %; Mono Craters, CA) was seeded with 20 and 40 vol. % euhedral corundum crystals (350 μm) to approximate phenocrysts. Experiments were run using TZM (Ti-Zr-Mo alloy) vessels fitted with a water-cooled rapid quench top in a vertical Deltech furnace. Each run was held at 110 MPa and 900OC for 24 hours then decompressed continuously at a rate of 0.25 MPa/s to a final pressure (Pf) between 75 and 15 MPa. Permeability was measured using a bench-top permeameter constructed for the small experimental samples. Porosity was obtained from reflected light images using NIH Image J. The porosity of the samples increased from 11.0±1.7 to 73.3±3.1 vol % at Pf of 75 to 15 MPa for crystal free samples, 30.1±6.9 to 62.2±2.6 vol % at Pf of of 75 to 25 MPa for 20 vol % crystal samples, and 13.3±2.5 to 41.2±9.6 vol % at Pf of 75 to 50 MPa for 40 vol % crystal samples. The 20 vol % samples are impermeable up to at least 50 MPa Pf. The 40 vol % samples are impermeable up to 25 MPa Pf, with one sample having a measured Darcian permeability of -13.93±0.05 m2 at 25 MPa Pf. Comparatively, the crystal free samples were mostly impermeable up to 15 MPa, with one sample having a measured Darcian permeability of -14.41±0.04 m2 at 15 MPa Pf and 73.3 vol % porosity. Although preliminary, our permeable 40 vol % experiment suggests the phenocrysts help the samples develop permeability at a higher ending pressure and potentially lower porosity. Differences in the porosity curve as a function of pressure between the 20 and 40 vol % series indicate phenocrysts influence the vesicle structures in ascending magmas.

Mechanical behavior in the Nankai inner accretionary prism, IODP Site C0002

NASA Astrophysics Data System (ADS)

Valdez, R. D., II; Saffer, D. M.

2017-12-01

Understanding the processes that control seismogenesis and stress state at subduction zones requires knowledge of fault zone and sediment physical and mechanical properties. As part of the International Ocean Discovery Program (IODP) Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE), Expedition 348 drilled into the Kumano forearc basin and underlying inner accretionary prism at Site C0002, located 35 km landward of the trench. One primary objective was to sample and characterize the mechanical behavior of the inner accretionary prism. Here we report on the frictional and unconfined compressive strength (UCS) of mudstone samples and a clay-rich shear zone recovered from 2182-2209 meters below sea floor (mbsf), determined from triaxial deformation tests at confining pressures from 1 to 7 MPa (UCS measurements on mudstones) and 36 MPa (strength of fault zone). Our results show that at a confining pressure of 1 MPa, the wall rock sediments fail at a peak differential stress of 9.1 MPa with a residual stress of 2.8 MPa. A clear peak and evolution to residual strength remains present at 7 MPa, and both the peak and residual strengths of the mudstones increases systematically with confining pressure. At a confining pressure of 36 MPa, the shear zone sediment yields at a differential stress of 25.2 MPa followed by strain-hardening to a maximum stress of 33.1 MPa. The shear zone is frictionally weaker than the surrounding mudstones, with a friction coefficient (μ) of 0.26-0.31, versus µ = 0.45 for the wall rock. The suite of tests defines a UCS for the mudstone of 7.9 MPa. Our friction data suggest that the inner wedge may be weaker than commonly assumed in applications of critical wedge theory to estimate the properties and conditions in accretionary prisms. One key implication is that for a given basal detachment friction coefficient, higher basal pore pressures (or lower wedge pore pressures) would be required to sustain observed taper angles. Additionally, the UCS we define is significantly lower than predicted by widely-adopted empirical relations between P wave velocity and UCS for shales (UCS of 15.5 MPa), suggesting that existing analyses of stress magnitudes from borehole breakout widths may overestimate horizontal stress magnitudes.

Pre-eruptive storage conditions and continuous decompression relations of rhyodacite magma erupted from Chaos Crags, Lassen Volcanic Center, California

NASA Astrophysics Data System (ADS)

Quinn, E. T.; Andrews, B. J.; Schwab, B. E.; Clynne, M. A.

2013-12-01

We performed a series of hydrothermal (high-temperature and -pressure) phase equilibrium experiments on a natural rhyodacite pumice from the 1103 ×13 years BP pyroclastic flow from the Chaos Crags, Lassen Volcanic Center, California. The pumice (LQ13-01, collected at the same location as LC84-417 (69.58 wt. % SiO2) by Clynne) is from the lower pyroclastic flow member of the group 1 lavas, the most silicic products known of Chaos Crags. Group 1 lavas are homogeneous (69-70 wt. % SiO2), petrographically and compositionally similar with rare to sparse mafic inclusions, and comprise the earliest emplaced units of Chaos Crags, the lower, middle, and upper pyroclastic flows, and domes A and B, whereas group 2 are comparatively heterogeneous (67-69 wt. % SiO2), with increasing abundance (10-15%) of mafic inclusions throughout the emplacement sequence, and comprise domes C through F. The phase assemblage in the natural sample used as experimental starting material comprises phenocrysts of quartz, plagioclase feldspars with rims of ~An35, biotite, hornblende, and Fe-Ti oxides in a vesiculated glassy matrix. Trace mafic enclaves are also present, but were removed from experimental starting material. All experiments were performed at the Smithsonian Institution. Experiments were run under H2O-saturated conditions at pressures of 75 MPa to 200 MPa and temperatures of 750°C to 900°C, at oxygen fugacity NNO+1 (×0.5-log-units), for 93 to 132 hours. EPMA and SEM analyses of experimental products show quartz is stable from <200 MPa at 750°C to <150 MPa at 800°C and is not stable at temperatures >800°C, within the investigated range. Amphibole is stable from >75 MPa at 750°C to >100 MPa at 800°C to 200 MPa at <850°C, and is not stable ≤75 MPa or ≥850°C. Biotite is stable at <800°C at 75 MPa to <825°C at 200 MPa, and not stable for any pressure at ≥850°C. Pyroxene, not present in the starting material is stable for 200MPa at >775°C and all pressures at temperatures ≥825°C, within the investigated range. FTIR analysis of quartz-hosted melt inclusions contain 4.0-5.0 wt. % H2O (average 4.3 wt. %), suggesting saturation pressures of 100-110 MPa (calculated using model of Papale et al., 2006). Comparison of the natural samples with the experimentally determined phase diagram and melt inclusions, suggests pre-eruptive storage conditions of 110-125 MPa and 775°C; given FeTi-oxide temperatures of 850 °C, magma may have been heated by as much as 75-100°C immediately prior to eruption. Ongoing work includes EPMA analysis of plagioclase feldspars and amphiboles to further constrain An-stability and hornblende-cummingtonite relations , respectively, and analysis of titanomagnetite-ilmenite pairs. Continuous decompression experiments are underway with rates ranging from 0.3 MPa/hr to 7.5 MPa/hr, corresponding to total decompression times of 16 hours to 18 days.

Microstructure, Pitting Corrosion Resistance and Impact Toughness of Duplex Stainless Steel Underwater Dry Hyperbaric Flux-Cored Arc Welds

PubMed Central

Hu, Yu; Shen, Xiao-Qin; Wang, Zhong-Min

2017-01-01

Duplex stainless steel multi-pass welds were made at 0.15 MPa, 0.45 MPa, and 0.75 MPa pressure, simulating underwater dry hyperbaric welding by the flux-cored arc welding (FCAW) method, with welds of normal pressure as a benchmark. The purpose of this work was to estimate the effect of ambient pressure on the microstructure, pitting corrosion resistance and impact toughness of the weld metal. The microstructure measurement revealed that the ferrite content in the weld metal made at 0.45 MPa is the lowest, followed by that of 0.75 MPa and 0.15 MPa. The analysis of potentiodynamic polarization tests at 30 °C and 50 °C demonstrated that the pitting corrosion resistance depends on the phases of the lower pitting resistance equivalent numbers (PREN), secondary austenite and ferrite. The weld metal made at 0.45 MPa had the best resistance to pitting corrosion at 30 °C and 50 °C with the highest PRENs of secondary austenite and ferrite. The weld metal made at 0.15 MPa displayed the lowest pitting corrosion resistance at 30 °C with the lowest PREN of secondary austenite, while the weld metal made at 0.75 MPa was the most seriously eroded after being tested at 50 °C for the lowest PREN of ferrite, with large cluster pits seen in ferrite at 50 °C. The impact tests displayed a typical ductile-brittle transition because of the body-centered cubic (BCC) structure of the ferrite when the test temperature was lowered. All the weld metals met the required value of 34 J at −40 °C according to the ASTM A923. The highest ferrite content corresponded to the worst impact toughness, but the highest toughness value did not correspond to the greatest austenite content. With the decreasing of the test temperature, the drop value of absorbed energy was correlated to the ferrite content. Additionally, in this work, the weld metal made at 0.45 MPa had the best combined properties of pitting resistance and impact toughness. PMID:29258262

Progestins Upregulate FKBP51 Expression in Human Endometrial Stromal Cells to Induce Functional Progesterone and Glucocorticoid Withdrawal: Implications for Contraceptive- Associated Abnormal Uterine Bleeding.

PubMed

Guzeloglu Kayisli, Ozlem; Kayisli, Umit A; Basar, Murat; Semerci, Nihan; Schatz, Frederick; Lockwood, Charles J

2015-01-01

Use of long-acting progestin only contraceptives (LAPCs) offers a discrete and highly effective family planning method. Abnormal uterine bleeding (AUB) is the major side effect of, and cause for, discontinuation of LAPCs. The endometria of LAPC-treated women display abnormally enlarged, fragile blood vessels, decreased endometrial blood flow and oxidative stress. To understanding to mechanisms underlying AUB, we propose to identify LAPC-modulated unique gene cluster(s) in human endometrial stromal cells (HESCs). Protein and RNA isolated from cultured HESCs treated 7 days with estradiol (E2) or E2+ medroxyprogesterone acetate (MPA) or E2+ etonogestrel (ETO) or E2+ progesterone (P4) were analyzed by quantitative Real-time (q)-PCR and immunoblotting. HSCORES were determined for immunostained-paired endometria of pre-and 3 months post-Depot MPA (DMPA) treated women and ovariectomized guinea pigs (GPs) treated with placebo or E2 or MPA or E2+MPA for 21 days. In HESCs, whole genome analysis identified a 67 gene group regulated by all three progestins, whereas a 235 gene group was regulated by E2+ETO and E2+MPA, but not E2+P4. Ingenuity pathway analysis identified glucocorticoid receptor (GR) activation as one of upstream regulators of the 235 MPA and ETO-specific genes. Among these, microarray results demonstrated significant enhancement of FKBP51, a repressor of PR/GR transcriptional activity, by both MPA and ETO. q-PCR and immunoblot analysis confirmed the microarray results. In endometria of post-DMPA versus pre-DMPA administered women, FKBP51 expression was significantly increased in endometrial stromal and glandular cells. In GPs, E2+MPA or MPA significantly increased FKBP51 immunoreactivity in endometrial stromal and glandular cells versus placebo- and E2-administered groups. MPA or ETO administration activates GR signaling and increases endometrial FKBP51 expression, which could be one of the mechanisms causing AUB by inhibiting PR and GR-mediated transcription. The resultant PR and/or GR-mediated functional withdrawal may contribute to associated endometrial inflammation, aberrant angiogenesis, and bleeding.

Inactivation of Anisakis simplex L3 in the flesh of white spotted conger (Conger myriaster) by high hydrostatic pressure and its effect on quality.

PubMed

Lee, Ki-Hoon; Park, Shin Young; Ha, Sang-Do

2016-06-01

Koreans consume much seafood; the country is surrounded on the east, west and south by the sea. Koreans have eaten raw sashimi for a long time. However, a concern in the raw sea food industry is that the parasitic nematode Anisakis simplex L3 occurs naturally in marine fish. Thus, the fishery industry needs a non-thermal processing method. High hydrostatic pressure (HPP) has been demonstrated to be effective. White spotted conger flesh containing 20 live larvae was exposed to different pressures (150 and 200 MPa for 1 and 5 min; 250 and 300 MPa each for 1 min). The viability of A. simplex L3 was significantly (p < 0.05) reduced in the flesh of white spotted conger by the stepwise increase of high pressure and time. The conditions required to eliminate A. simplex L3 were as follows: 200 MPa for 5 min or 300 MPa for 1 min. The flesh of the white spotted conger treated at 300 MPa for 1 min was whiter and yellower than untreated controls or that treated at 200 MPa for 5 min. No significant changes (p > 0.05) in any of the Hunter colour ('L', 'a' and 'b') values were found after HPP at 200 MPa for 5 min. The fresh treated at 300 MPa for 1 min scored < 4.0 (the defect limit of quality) of flavour, texture and overall acceptability in untrained sensory evaluation using a seven-point hedonic scale. However, the flesh treated at 200 MPa for 5 min scored > 5.0 ('like') for all sensory parameters. This study suggested that HPP at 200 MPa for 5 min could potentially be used for the inactivation of A. simplex L3 in raw fishery food products without any concomitant changes in their colour or sensory qualities.

Microstructure, Pitting Corrosion Resistance and Impact Toughness of Duplex Stainless Steel Underwater Dry Hyperbaric Flux-Cored Arc Welds.

PubMed

Hu, Yu; Shi, Yong-Hua; Shen, Xiao-Qin; Wang, Zhong-Min

2017-12-18

Duplex stainless steel multi-pass welds were made at 0.15 MPa, 0.45 MPa, and 0.75 MPa pressure, simulating underwater dry hyperbaric welding by the flux-cored arc welding (FCAW) method, with welds of normal pressure as a benchmark. The purpose of this work was to estimate the effect of ambient pressure on the microstructure, pitting corrosion resistance and impact toughness of the weld metal. The microstructure measurement revealed that the ferrite content in the weld metal made at 0.45 MPa is the lowest, followed by that of 0.75 MPa and 0.15 MPa. The analysis of potentiodynamic polarization tests at 30 °C and 50 °C demonstrated that the pitting corrosion resistance depends on the phases of the lower pitting resistance equivalent numbers (PREN), secondary austenite and ferrite. The weld metal made at 0.45 MPa had the best resistance to pitting corrosion at 30 °C and 50 °C with the highest PRENs of secondary austenite and ferrite. The weld metal made at 0.15 MPa displayed the lowest pitting corrosion resistance at 30 °C with the lowest PREN of secondary austenite, while the weld metal made at 0.75 MPa was the most seriously eroded after being tested at 50 °C for the lowest PREN of ferrite, with large cluster pits seen in ferrite at 50 °C. The impact tests displayed a typical ductile-brittle transition because of the body-centered cubic (BCC) structure of the ferrite when the test temperature was lowered. All the weld metals met the required value of 34 J at -40 °C according to the ASTM A923. The highest ferrite content corresponded to the worst impact toughness, but the highest toughness value did not correspond to the greatest austenite content. With the decreasing of the test temperature, the drop value of absorbed energy was correlated to the ferrite content. Additionally, in this work, the weld metal made at 0.45 MPa had the best combined properties of pitting resistance and impact toughness.

Effects of topically applied rapamycin and mycophenolic acid on TNCB-induced atopic dermatitis-like skin lesions in NC/Nga mice.

PubMed

Jung, Kyung Eun; Lee, Ye Jin; Ryu, Yun Hee; Kim, Jung Eun; Kim, Hei Sung; Kim, Beom Joon; Kang, Hoon; Park, Young Min

2015-06-01

Rapamycin (RPM) and mycophenolic acid (MPA) are immunosuppressive drugs approved for use in preventing transplant rejection. These drugs have also been used in the field of dermatology as glucocorticoid sparing agents for autoimmune and inflammatory disorders such as atopic dermatitis (AD). The aim of this study was to investigate the therapeutic effect of topically applied RPM and/or MPA on AD-like skin lesions in NC/Nga mice. RPM (0.04% - 4%), MPA (0.2% - 5%), and formulations of both agents at various ratios were administrated topically to NC/Nga mice with 2-chloro-1,3,5-trinitrobenzene (TNCB)-induced AD-like skin lesions. The therapeutic effects of topical RPM, MPA, and the mixed formulations in TNCB-treated NC/Nga mice were assessed by measuring skin severity scores, ear thickness, and histological changes in the lesioned skin including mast cell count and total serum IgE levels. Expression of interleukin (IL)-4, and interferon (IFN)-γ was also assessed. Topical 4% RPM and/or 1% MPA treatment significantly improved clinical signs of AD such as erythema, edema, excoriation, and dryness on day 29 (P<0.05). In addition, 4% RPM, 1% MPA, and the mixed formulations significantly decreased epidermal thickening, dermal edema, and cellular infiltration into the dermis compared with the vehicle. RPM (4%) and/or MPA (1%) significantly reduced the expression of IL-4 and IFN-γ mRNA and protein levels compared with the vehicle (P<0.05). No significant change in the levels of total serum IgE was induced by topical 4% RPM and/or 1% MPA. The present results demonstrated that topical 4% RPM and/or 1% MPA improved TNCB-induced AD-like lesions of NC/Nga mice by suppressing expression of Th2-related cytokines (IL-4) and Th1-related cytokines (IFN-γ). These findings suggest that RPM and/or MPA may be promising topical therapeutic candidates for the treatment of AD. Copyright © 2015 Elsevier B.V. All rights reserved.

[The effects of different welding wires on the mechanical properties of laser welding joints].

PubMed

Huang, Qing-feng; Zhang, Jian-zhong; Jiang, Wei-dong; Li, Quan; Yu, Jin-xing

2006-08-01

To evaluate the mechanical properties and microstructure of laser-welded joints with different welding wires for clinical use of welding wire. The standard tensile test and three-point bending test rods were made from Co-Cr and Ni-Cr alloy, and were laser-welded with different welding wire (commercially welding wire and casting wire). Then the tensile rods were tested for the ultimate tensile strength (UTS), and the bending rods for the ultimate bending strength (UBS). The results was analyzed by one-way ANOVA. The tensile fracture surface were examined by scanning electron microscopy (SEM). Metallurgical analysis were also performed on polished longitudinal sectioned samples. For Co-Cr alloy, the UTS of casting wire group and commercially welding wire group was respectively (606.40+/-82.53)MPa and (693.61+/-47.68)MPa; the UBS was respectively (997.95+/-88.89)MPa and (1160.76+/-91.59)MPa. ANOVA showed a significant difference of UTS and UBS between the two groups at the 0.05 level (P<0.05). For Ni-Cr alloy, the UTS of casting wire group and commercially welding wire group was respectively (558.14+/-46.75)MPa and (582.32+/-35.43)MPa; the UBS was respectively (1084.75+/-46.02)MPa and (1078.29+/-36.25)MPa. There was no significant difference between the two groups (P>0.05). SEM and metallurgical examination showed the welded zone exhibiting more cracks in the casting wire group than in the commercially welding wire group. It would be advisable to work with commercially welding wire for the joints that need better strength.

Influence of platform and abutment angulation on peri-implant bone. A three-dimensional finite element stress analysis.

PubMed

Martini, Ana Paula; Barros, Rosália Moreira; Júnior, Amilcar Chagas Freitas; Rocha, Eduardo Passos; de Almeida, Erika Oliveira; Ferraz, Cacilda Cunha; Pellegrin, Maria Cristina Jimenez; Anchieta, Rodolfo Bruniera

2013-12-01

The aim of this study was to evaluate stress distribution on the peri-implant bone, simulating the influence of Nobel Select implants with straight or angulated abutments on regular and switching platform in the anterior maxilla, by means of 3-dimensional finite element analysis. Four mathematical models of a central incisor supported by external hexagon implant (13 mm × 5 mm) were created varying the platform (R, regular or S, switching) and the abutments (S, straight or A, angulated 15°). The models were created by using Mimics 13 and Solid Works 2010 software programs. The numerical analysis was performed using ANSYS Workbench 10.0. Oblique forces (100 N) were applied to the palatine surface of the central incisor. The bone/implant interface was considered perfectly integrated. Maximum (σmax) and minimum (σmin) principal stress values were obtained. For the cortical bone the highest stress values (σmax) were observed in the RA (regular platform and angulated abutment, 51 MPa), followed by SA (platform switching and angulated abutment, 44.8 MPa), RS (regular platform and straight abutment, 38.6 MPa) and SS (platform switching and straight abutment, 36.5 MPa). For the trabecular bone, the highest stress values (σmax) were observed in the RA (6.55 MPa), followed by RS (5.88 MPa), SA (5.60 MPa), and SS (4.82 MPa). The regular platform generated higher stress in the cervical periimplant region on the cortical and trabecular bone than the platform switching, irrespective of the abutment used (straight or angulated).

A Gas Pressure Scale Based on Primary Standard Piston Gauges

PubMed Central

Olson, Douglas A.; Driver, R. Greg; Bowers, Walter J.

2010-01-01

The National Institute of Standards and Technology (NIST) has redefined its gas pressure scale, up to 17 MPa, based on two primary standard piston gauges. The primary standard piston gauges are 35.8 mm in diameter and operate from 20 kPa to 1 MPa. Ten secondary standard piston gauges, two each of five series of the Ruska 2465 type, with successively smaller diameters form the scale extending up to 17 MPa. Six of the piston gauges were directly compared to the primary standards to determine their effective area and expanded (k = 2) uncertainty. Two piston gauges operating to 7 MPa were compared to the 1.4 MPa gauges, and two piston gauges operating to 17 MPa were compared to the 7 MPa gauges. Distortion in the 7 MPa piston gauges was determined by comparing those gauges to a DH Instruments PG7601 type piston gauge, whose distortion was calculated using elasticity theory. The relative standard uncertainties achieved by the primary standards range from 3.0 × 10−6 to 3.2 × 10−6. The relative standard uncertainty of the secondary standards is as low as 4.2 × 10−6 at 300 kPa. The effective areas and uncertainties were validated by comparison to standards of other National Metrology Institutes (NMIs). Results show agreement in all cases to better than the expanded (k = 2) uncertainty of the difference between NIST and the other NMIs, and in most cases to better than the standard (k = 1) uncertainty of the difference. PMID:27134793

Validation of a dew-point generator for pressures up to 6 MPa using nitrogen and air

NASA Astrophysics Data System (ADS)

Bosma, R.; Mutter, D.; Peruzzi, A.

2012-08-01

A new primary humidity standard was developed at VSL that, in addition to ordinary operation with air and nitrogen at atmospheric pressure, can be operated with other carrier gases such as natural gas at pressures up to 6 MPa and SF6 at pressures up to 1 MPa. The temperature range of the standard is from -80 °C to +20 °C. In this paper, we report the validation of the new primary dew-point generator in the temperature range -41 °C to +5 °C and the pressure range 0.1 MPa to 6 MPa using nitrogen and air. For the validation the flow through the dew-point generator was varied up to 10 l min-1 (at 23 °C and 1013 hPa) and the dew point of the gas entering the generator was varied up to 15 °C above the dew point exiting the generator. The validation results showed that the new generator, over the tested temperature and pressure range, can be used with a standard uncertainty of 0.02 °C frost/dew point. The measurements used for the validation at -41 °C and -20 °C with nitrogen and at +5 °C with air were also used to calculate the enhancement factor at pressures up to 6 MPa. For +5 °C the differences between the measured and literature values were compatible with the respective uncertainties. For -41 °C and -20 °C they were compatible only up to 3 MPa. At 6 MPa a discrepancy was observed.

Mechanical Analysis of Cartilage Graft Reinforced with PDS Plate

PubMed Central

Conderman, Christian; Kinzinger, Michael; Manuel, Cyrus; Protsenko, Dmitry; Wong, Brian J. F.

2014-01-01

Objectives/Hypothesis This study attempts to characterize the biomechanical properties of a PDS-cartilage composite graft for use in septorhinoplasty. Study Design Experimental Study. Methods This study used a PDS analog, porcine cartilage cut to 1 × 5 × 20 mm, and a mechanical testing platform to measure flexure of a composite graft. Samples were assessed in four groups based on variations in suture pattern and orientation. The platform measured the force required to deflect the sample 2 mm in single cantilever beam geometry before and after the polymer was affixed to the specimen. Elastic Moduli were calculated before and after application of the polydioxanone polymer. Results The average modulus of the cartilage alone was 17 ± 0.9 MPa. The modulus of the composite cartilage-polymer graft with 2 suture fixation was 21.2 ± 1.5 MPa. The 3-suture configuration produced an increase to 25.8 ± 2.23 MPa. The four-suture configuration produced 23.1 ± 3.19 MPa. The five-suture configuration produced 25.7 ± 2.6 MPa. The modulus of the analog alone was 170 ± 30 MPa. The modulus of the 0.5 mm PDS was 692 ± 37.4 MPa. The modulus of the 0.15 mm perforated PDS was 447 ± 34.8 MPa. Conclusions The study found that suturing a polymer plate to cartilage resulted in enhanced stiffness of the composite. Under the conditions of the study, there was no significant difference in elastic moduli between suture configurations, making the two-suture linear configuration optimal in the one-plane cantilever deflection model. PMID:22965809

Numerical stress analysis of the iris tissue induced by pupil expansion: Comparison of commercial devices

PubMed Central

Wang, Xiaofei; Perera, Shamira A.; Girard, Michaël J. A.

2018-01-01

Purpose (1) To use finite element (FE) modelling to estimate local iris stresses (i.e. internal forces) as a result of mechanical pupil expansion; and to (2) compare such stresses as generated from several commercially available expanders (Iris hooks, APX dilator and Malyugin ring) to determine which design and deployment method are most likely to cause iris damage. Methods We used a biofidelic 3-part iris FE model that consisted of the stroma, sphincter and dilator muscles. Our FE model simulated expansion of the pupil from 3 mm to a maximum of 6 mm using the aforementioned pupil expanders, with uniform circular expansion used for baseline comparison. FE-derived stresses, resultant forces and area of final pupil opening were compared across devices for analysis. Results Our FE models demonstrated that the APX dilator generated the highest stresses on the sphincter muscles, (max: 6.446 MPa; average: 5.112 MPa), followed by the iris hooks (max: 5.680 MPa; average: 5.219 MPa), and the Malyugin ring (max: 2.144 MPa; average: 1.575 MPa). Uniform expansion generated the lowest stresses (max: 0.435MPa; average: 0.377 MPa). For pupil expansion, the APX dilator required the highest force (41.22 mN), followed by iris hooks (40.82 mN) and the Malyugin ring (18.56 mN). Conclusion Our study predicted that current pupil expanders exert significantly higher amount of stresses and forces than required during pupil expansion. Our work may serve as a guide for the development and design of next-generation pupil expanders. PMID:29538452

Nonprofit Management Education in MPA Programs: Lessons for Successful Track Building

ERIC Educational Resources Information Center

Gerlach, John David

2016-01-01

As the American nonprofit sector continues to grow, so does interest in nonprofit management graduate education. MPA programs play a significant role in preparing students for work in the nonprofit field. This article examines nonprofit management as an area of graduate study, paying particular attention to how NASPAA-accredited MPA programs…

The application of high-pressure treatment in the reduction of phosphate levels in breakfast sausages.

PubMed

O'Flynn, C C; Cruz-Romero, M C; Troy, D J; Mullen, A M; Kerry, J P

2014-01-01

This study investigated effects of high pressure (HP) treatment of pork meat at 150 or 300 MPa for 5 min before manufacturing sausages on the reduction of phosphate levels and compared to sausages manufactured with untreated pork meat (control sausages). Improvement in perceived saltiness, juiciness and overall flavour was observed in sausages manufactured using HP-treated meat at 150 MPa and 0% phosphate, compared to control sausages. Sausages manufactured using meat HP-treated at 150 MPa and 0.25% phosphate (P<0.05) improved hardness of sausages. HP-treated meat at 300 MPa and 0% phosphate decreased juiciness and adhesiveness, while at 0.25% phosphate, adversely affected emulsion stability and sensory attributes. HP treatment did not affect significantly the lightness of the sausages; however, elimination of phosphate reduced (P<0.05) the yellowness, while HP treatment at 150 MPa with 0.25 or 0.5% phosphate increased (P<0.05) redness. HP reatment at 150 MPa has potential for reducing phosphate levels in sausages without significant changes in their functionality and improved acceptability. © 2013.

Impact of post-rigor high pressure processing on the physicochemical and microbial shelf-life of cultured red abalone (Haliotis rufescens).

PubMed

Hughes, Brianna H; Perkins, L Brian; Yang, Tom C; Skonberg, Denise I

2016-03-01

High pressure processing (HPP) of post-rigor abalone at 300MPa for 10min extended the refrigerated shelf-life to four times that of unprocessed controls. Shucked abalone meats were processed at 100 or 300MPa for 5 or 10min, and stored at 2°C for 35days. Treatments were analyzed for aerobic plate count (APC), total volatile base nitrogen (TVBN), K-value, biogenic amines, color, and texture. APC did not exceed 10(6) and TVBN levels remained below 35mg/100g for 35days for the 300MPa treatments. No biogenic amines were detected in the 300MPa treatments, but putrescine and cadaverine were detected in the control and 100MPa treatments. Color and texture were not affected by HPP or storage time. These results indicate that post-rigor processing at 300MPa for 10min can significantly increase refrigerated shelf-life of abalone without affecting chemical or physical quality characteristics important to consumers. Copyright © 2015 Elsevier Ltd. All rights reserved.

High pressure applied to frozen ham at different process stages. 2. Effect on the sensory attributes and on the colour characteristics of dry-cured ham.

PubMed

Serra, X; Grèbol, N; Guàrdia, M D; Guerrero, L; Gou, P; Masoliver, P; Gassiot, M; Sárraga, C; Monfort, J M; Arnau, J

2007-01-01

This paper describes the effect of high pressure (400MPa and 600MPa) applied to frozen hams at early stages of the dry-cured ham process: green hams (GH) and hams at the end of the resting stage (ERS), on the appearance, some texture and flavour parameters and on the instrumental colour characteristics of dry-cured hams. Pressurized hams showed slightly lower visual colour intensity than the control ones. In general, pressurization did not have a significant effect on the flavour characteristics of the final product. The 600-MPa hams from the ERS process showed significantly lower crumbliness and higher fibrousness scores than the control and the 400-MPa hams. However, none of these differences were enough to affect the overall sensory quality of the hams negatively. Regarding instrumental colour characteristics (L(∗)a(∗)b(∗)), an increase in lightness was observed in the biceps femoris muscle from GH hams pressurized at 400MPa and 600MPa but not in the ERS hams.

A meta-analysis of the effects of shockwave and high pressure processing on color and cook loss of fresh meat.

PubMed

Ha, Minh; Dunshea, Frank R; Warner, Robyn D

2017-10-01

Meta-analysis is a statistical approach for investigating experimental differences across studies. Meta-analyses were performed to examine the effects of hydrodynamic processing (shockwave; n=12 papers) and high pressure processing (HPP; n=8 papers) on the color and cook loss of fresh meat. Shockwave did not affect color (L*, a*), whereas cook loss was increased by 0.6% relative to untreated meat. HPP resulted in an increase in lightness (L*) and a decrease in redness (a*), with the effect being greater at higher pressures (>300MPa vs <300MPa). In addition, HPP applied at moderate pressure (<300MPa) reduced cook loss but at high pressure (>300MPa) the cook loss was increased (-1.5% vs 3.0% respectively). The increased cook loss with shockwave and high pressure (>300MPa) processing needs to be balanced against benefits in texture if this technology is applied to meat. The reduced cook loss of meat treated at moderate pressures (<300MPa) is an advantage which would likely improve sensory traits. Copyright © 2017 Elsevier Ltd. All rights reserved.

Phase diagram and high-pressure boundary of hydrate formation in the ethane-water system.

PubMed

Kurnosov, Alexander V; Ogienko, Andrey G; Goryainov, Sergei V; Larionov, Eduard G; Manakov, Andrey Y; Lihacheva, Anna Y; Aladko, Eugeny Y; Zhurko, Fridrikh V; Voronin, Vladimir I; Berger, Ivan F; Ancharov, Aleksei I

2006-11-02

Dissociation temperatures of gas hydrate formed in the ethane-water system were studied at pressures up to 1500 MPa. In situ neutron diffraction analysis and X-ray diffraction analysis in a diamond anvil cell showed that the gas hydrate formed in the ethane-water system at 340, 700, and 1840 MPa and room temperature belongs to the cubic structure I (CS-I). Raman spectra of C-C vibrations of ethane molecules in the hydrate phase, as well as the spectra of solid and liquid ethane under high-pressure conditions were studied at pressures up to 6900 MPa. Within 170-3600 MPa Raman shift of the C-C vibration mode of ethane in the hydrate phase did not show any discontinuities, which could be evidence of possible phase transformations. The upper pressure boundary of high-pressure hydrate existence was discovered at the pressure of 3600 MPa. This boundary corresponds to decomposition of the hydrate to solid ethane and ice VII. The type of phase diagram of ethane-water system was proposed in the pressure range of hydrate formation (0-3600 MPa).

High pressure droplet burning experiments in reduced gravity

NASA Technical Reports Server (NTRS)

Chauveau, Christian; Goekalp, Iskender

1995-01-01

A parametric investigation of single droplet gasification regimes is helpful in providing the necessary physical ideas for sub-grid models used in spray combustion numerical prediction codes. A research program has been initiated at the LCSR to explore the vaporization regimes of single and interacting hydrocarbon and liquid oxygen droplets under high pressure conditions. This paper summarizes the status of the LCSR program on the high pressure burning of single fuel droplets; recent results obtained under normal and reduced gravity conditions with suspended droplets are presented. In the work described here, parabolic flights of the CNES Caravelle is used to create a reduced gravity environment of the order of 10(exp -2) g(sub O). For all the droplet burning experiments reported here, the suspended droplet initial diameters are scattered around 1.5 mm; and the ambient air temperature is 300 K. The ambient pressure is varied between 0.1 MPa and 12 MPa. Four fuels are investigated: methanol (Pc = 7.9 MPa), n-heptane (Pc = 2.74 MPa), n-hexane (Pc = 3.01 MPa) and n-octane (Pc = 2.48 MPa).

Spatial, socio-economic, and ecological implications of incorporating minimum size constraints in marine protected area network design.

PubMed

Metcalfe, Kristian; Vaughan, Gregory; Vaz, Sandrine; Smith, Robert J

2015-12-01

Marine protected areas (MPAs) are the cornerstone of most marine conservation strategies, but the effectiveness of each one partly depends on its size and distance to other MPAs in a network. Despite this, current recommendations on ideal MPA size and spacing vary widely, and data are lacking on how these constraints might influence the overall spatial characteristics, socio-economic impacts, and connectivity of the resultant MPA networks. To address this problem, we tested the impact of applying different MPA size constraints in English waters. We used the Marxan spatial prioritization software to identify a network of MPAs that met conservation feature targets, whilst minimizing impacts on fisheries; modified the Marxan outputs with the MinPatch software to ensure each MPA met a minimum size; and used existing data on the dispersal distances of a range of species found in English waters to investigate the likely impacts of such spatial constraints on the region's biodiversity. Increasing MPA size had little effect on total network area or the location of priority areas, but as MPA size increased, fishing opportunity cost to stakeholders increased. In addition, as MPA size increased, the number of closely connected sets of MPAs in networks and the average distance between neighboring MPAs decreased, which consequently increased the proportion of the planning region that was isolated from all MPAs. These results suggest networks containing large MPAs would be more viable for the majority of the region's species that have small dispersal distances, but dispersal between MPA sets and spill-over of individuals into unprotected areas would be reduced. These findings highlight the importance of testing the impact of applying different MPA size constraints because there are clear trade-offs that result from the interaction of size, number, and distribution of MPAs in a network. © 2015 Society for Conservation Biology.

Pharmacokinetic Variability of Mycophenolic Acid in Pediatric and Adult Patients With Hematopoietic Stem Cell Transplantation.

PubMed

Zhang, Daping; Renbarger, Jamie L; Chow, Diana S-L

2016-11-01

The aim of this study was to evaluate the pharmacokinetic variations of mycophenolic acid (MPA), the active metabolite of mycophenolate mofetil (MMF), in both pediatric and adult patients following hematopoietic stem cell transplantation (HSCT). Twenty pediatric patients with a median age of 3 years (range 0.2-12 years) and 13 adult patients with a median age of 54 years (range 18-63 years) were enrolled. Blood samples were collected on days 0, 7, 14, 21, and 30 after allogeneic HSCT. Total and free (unbound) MPA as well as MPA 7-O-glucuronide (MPAG) were quantified using a validated LC-MS/MS assay. The plasma protein binding of MPA and MPAG did not change significantly in pediatric patients over the 1-month sampling period post-HSCT. However, it increased in adult patients from day 7 to day 30 post-HSCT, from 97.3 ± 0.8% to 98.3 ± 0.6% for MPA (P < .05), and 74.6 ± 9.4% to 82.9 ± 8.1% for MPAG (P < .05). The plasma protein binding of MPA was significantly higher in males compared to females in both pediatric (98.3 ± 1.1% vs 97.4 ± 1.1%) and adult (98.1 ± 0.7% vs 97.4 ± 1.2%) patients (P < .05). The MPAG/MPA ratios on a milligram-per-kilogram dose basis in adult patients were significantly higher than those in pediatric patients (4.3 ± 3.4 vs 2.4 ± 2.6; P < .05). Time-dependent plasma protein binding and age-related differences in MPA metabolism at least in part impact the reported large intra- and interindividual variability in MPA pharmacokinetics. These patient and pharmacologic factors, if incorporated into MMF regimen design and modification, may contribute to the rational dose selection of MMF in HSCT patients. © 2016, The American College of Clinical Pharmacology.

THE EFFECT OF HORMONE THERAPY ON MEAN BLOOD PRESSURE AND VISIT-TO-VISIT BLOOD PRESSURE VARIABILITY IN POSTMENOPAUSAL WOMEN: RESULTS FROM THE WOMEN’S HEALTH INITIATIVE RANDOMIZED CONTROLLED TRIALS

PubMed Central

Shimbo, Daichi; Wang, Lu; Lamonte, Michael J.; Allison, Matthew; Wellenius, Gregory A.; Bavry, Anthony A.; Martin, Lisa W.; Aragaki, Aaron; Newman, Jonathan D.; Swica, Yael; Rossouw, Jacques E.; Manson, JoAnn E.; Wassertheil-Smoller, Sylvia

2014-01-01

Objectives Mean and visit-to-visit variability (VVV) of blood pressure are associated with an increased cardiovascular disease risk. We examined the effect of hormone therapy on mean and VVV of blood pressure in postmenopausal women from the Women’s Health Initiative (WHI) randomized controlled trials. Methods Blood pressure was measured at baseline and annually in the two WHI hormone therapy trials in which 10,739 and 16,608 postmenopausal women were randomized to conjugated equine estrogens (CEE, 0.625 mg/day) or placebo, and CEE plus medroxyprogesterone acetate (MPA, 2.5 mg/day) or placebo, respectively. Results At the first annual visit (Year 1), mean systolic blood pressure was 1.04 mmHg (95% CI 0.58, 1.50) and 1.35 mmHg (95% CI 0.99, 1.72) higher in the CEE and CEE+MPA arms respectively compared to corresponding placebos. These effects remained stable after Year 1. CEE also increased VVV of systolic blood pressure (ratio of VVV in CEE vs. placebo, 1.03, P<0.001), whereas CEE+MPA did not (ratio of VVV in CEE+MPA vs. placebo, 1.01, P=0.20). After accounting for study drug adherence, the effects of CEE and CEE+MPA on mean systolic blood pressure increased at Year 1, and the differences in the CEE and CEE+MPA arms vs. placebos also continued to increase after Year 1. Further, both CEE and CEE+MPA significantly increased VVV of systolic blood pressure (ratio of VVV in CEE vs. placebo, 1.04, P<0.001; ratio of VVV in CEE+MPA vs. placebo, 1.05, P<0.001). Conclusions Among postmenopausal women, CEE and CEE+MPA at conventional doses increased mean and VVV of systolic blood pressure. PMID:24991872

Effect of tamoxifen, methoxyprogesterone acetate and combined treatment on cellular proliferation and apoptosis in SKOV3/DDP cells via the regulation of vascular endothelial growth factor.

PubMed

Wen, Lv; Hong, Ding; Yanyin, Wu; Mingyue, Zhang; Baohua, Li

2013-05-01

The aim of this study was to investigate the effect of tamoxifen (TAM), methoxyprogesterone acetate (MPA) and their combined treatment on cisplatin-resistant ovarian cancer SKOV3/DDP cells, as well as the potential mechanisms. MTT assay was used to investigate the effect of different concentrations (0.01, 0.1, 1, 10 and 100 μM) of TAM, MPA and their combined treatment on the proliferation of cisplatin-resistant ovarian cancer SKOV3/DDP cells. Flow cytometry was employed to analyze the cell cycle and apoptosis rate of SKOV3/DDP cells treated with medium concentration (10 μM) of TAM, MPA and their combined treatment. Change in the protein level of vascular endothelial growth factor (VEGF) in response to drug treatments was measured using Western-blot. The proliferation of SKOV3/DDP cells was inhibited by 1, 10 and 100 μM of TAM or MPA in a dose-dependent manner. Compared to the control group, 10 μM TAM could significantly arrest SKOV3/DDP cells in the G0/G1 stage and induce apoptosis (p < 0.01). However, 10 μM MPA only promoted cell apoptosis, while exhibited little effect on the cell cycle. We further found that 10 μM TAM could remarkably reduce the protein expression of VEGF, while 10 μM MPA only induce a slight reduction. Strikingly, the combined treatment of TAM and MPA exhibited additive effect on the proliferation, cell cycle, apoptosis rate and VEGF expression of SKOV3/DDP cells. We found that TAM, MPA and their combined treatment exhibited significant inhibitory effect on the cisplatin-resistant ovarian cancer SKOV3/DDP cells. Hence, TAM and MPA could be potential cytotoxic drugs to treat cisplatin-resistant patients with advanced ovarian cancer.

High hydrostatic pressure inactivation of murine norovirus and human noroviruses on green onions and in salsa.

PubMed

Sido, Robert F; Huang, Runze; Liu, Chuhan; Chen, Haiqiang

2017-02-02

In this study, high hydrostatic pressure (HHP) was evaluated as an intervention for human noroviruses (HuNoVs) in green onions and salsa. To determine the effect of water during HHP treatment on virus inactivation, a HuNoV surrogate, murine norovirus 1 (MNV-1), was inoculated onto green onions and then HHP-treated at 350MPa with or without water at 4 or 20°C. The presence of water enhanced HHP inactivation of MNV-1 on green onions at 4°C but not at 20°C. To test the temperature effect on HHP inactivation of MNV-1, inoculated green onions were HHP-treated at 300MPa at 1, 4 and 10°C. As the temperature decreased, MNV-1 became more sensitive to HHP treatment. HHP inactivation curves of MNV-1 on green onions and salsa were obtained at 300 or 350MPa for 0.5-3min at 1°C. All three inactivation curves showed a linear relationship between log reduction of MNV-1 and time. D values of HHP inactivation of MNV-1 on green onions were 1.10 and 0.61min at 300 and 350MPa, respectively. The D value of HHP inactivation of MNV-1 in salsa at 300MPa was 0.63min. HHP inactivation of HuNoV GI.1 and GII.4 on green onions and salsa was also conducted. To achieve >3 log reduction of HuNoV GI.1, HHP treatments for 2min at 1°C should be conducted at 600MPa and 500MPa for green onions and salsa, respectively. To achieve >3 log reduction of HuNoV GII.4, HHP treatments for 2min at 1°C should be conducted at 500MPa and 300MPa for green onions and salsa, respectively. Copyright © 2016 Elsevier B.V. All rights reserved.

Performance of three rapid screening methods in the detection of Schistosoma haematobium infection in school-age children in Southeastern Nigeria

PubMed Central

Okeke, Ogochukwu Caroline; Ubachukwu, Patience Obiageli

2014-01-01

Background A cross-sectional study of primary school children was conducted to evaluate and compare the performance of some rapid screening methods in the detection of Schistosoma haematobium infection in Nigeria Cement Factory (NigerCem) and Nike Lake areas of Southeastern Nigeria. Methods Urine samples of school children were examined for macro-haematuria and tested for micro-haematuria and proteinuria using reagent strips followed by egg microscopy. Self-reported haematuria was assessed using simple questionnaire. The performances of these rapid diagnoses singly and in combination were calculated using egg microscopy as gold standard. Results The prevalence of the infection was 26.6% in NigerCem and 5.1% in Nike Lake area, classifying these areas as moderate- and low-prevalence areas (MPA and LPA); while in the subsample used for self-reported haematuria, the prevalence was 27.2 and 4.2% in MPA and LPA, respectively. The positive predictive value (PPV) of micro-haematuria was comparable in MPA (55.26%) and LPA (57.89%). Overall PPV of macro-haematuria was 87.50% in MPA and 66.70% in LPA while in the detection of heavy infection; PPV was higher in LPA (75%) than in MPA (66.67%). In LPA and MPA, combination of micro-haematuria and proteinuria, and concomitant presence of macro-haematuria, micro-haematuria, and proteinuria had PPV of 83.33 and 63.16%, and 100 versus 66.67%, respectively. Generally, the rapid screening tests had lower negative predictive values (NPVs) in MPA than in LPA. The use of simple questionnaire increased the PPV of heavy infection in MPA (77.78%). This was further increased to 80% when self-reported haematuria was combined with micro-haematuria. Conclusion The result suggests that in MPA with chronic infections, combination of self-reported haematuria and micro-haematuria may reduce the chance of missing those who should be treated. PMID:24593687

Performance of three rapid screening methods in the detection of Schistosoma haematobium infection in school-age children in Southeastern Nigeria.

PubMed

Okeke, Ogochukwu Caroline; Ubachukwu, Patience Obiageli

2014-03-01

A cross-sectional study of primary school children was conducted to evaluate and compare the performance of some rapid screening methods in the detection of Schistosoma haematobium infection in Nigeria Cement Factory (NigerCem) and Nike Lake areas of Southeastern Nigeria. Urine samples of school children were examined for macro-haematuria and tested for micro-haematuria and proteinuria using reagent strips followed by egg microscopy. Self-reported haematuria was assessed using simple questionnaire. The performances of these rapid diagnoses singly and in combination were calculated using egg microscopy as gold standard. The prevalence of the infection was 26·6% in NigerCem and 5·1% in Nike Lake area, classifying these areas as moderate- and low-prevalence areas (MPA and LPA); while in the subsample used for self-reported haematuria, the prevalence was 27·2 and 4·2% in MPA and LPA, respectively. The positive predictive value (PPV) of micro-haematuria was comparable in MPA (55·26%) and LPA (57·89%). Overall PPV of macro-haematuria was 87·50% in MPA and 66·70% in LPA while in the detection of heavy infection; PPV was higher in LPA (75%) than in MPA (66·67%). In LPA and MPA, combination of micro-haematuria and proteinuria, and concomitant presence of macro-haematuria, micro-haematuria, and proteinuria had PPV of 83·33 and 63·16%, and 100 versus 66·67%, respectively. Generally, the rapid screening tests had lower negative predictive values (NPVs) in MPA than in LPA. The use of simple questionnaire increased the PPV of heavy infection in MPA (77·78%). This was further increased to 80% when self-reported haematuria was combined with micro-haematuria. The result suggests that in MPA with chronic infections, combination of self-reported haematuria and micro-haematuria may reduce the chance of missing those who should be treated.

Managing Drug-Drug Interaction Between Ombitasvir, Paritaprevir/Ritonavir, Dasabuvir, and Mycophenolate Mofetil.

PubMed

Lemaitre, Florian; Ben Ali, Zeineb; Tron, Camille; Jezequel, Caroline; Boglione-Kerrien, Christelle; Verdier, Marie-Clémence; Guyader, Dominique; Bellissant, Eric

2017-08-01

No drug-drug interaction study has been conducted to date for the combination of ombitasvir, paritaprevir/ritonavir, dasabuvir (3D), and mycophenolic acid (MPA). We here report the case of a hepatitis C virus-infected patient treated with 3D and MPA for vasculitis. In light of the threat of drug-drug interaction, the concentration of MPA was measured before, during, and 15 days after the end of the 3D treatment. Similar values were found at all 3 time points, thus indicating that there is probably no need to adapt MPA dosage to 3D.

Microbial activity at gigapascal pressures.

PubMed

Sharma, Anurag; Scott, James H; Cody, George D; Fogel, Marilyn L; Hazen, Robert M; Hemley, Russell J; Huntress, Wesley T

2002-02-22

We observed physiological and metabolic activity of Shewanella oneidensis strain MR1 and Escherichia coli strain MG1655 at pressures of 68 to 1680 megapascals (MPa) in diamond anvil cells. We measured biological formate oxidation at high pressures (68 to 1060 MPa). At pressures of 1200 to 1600 MPa, living bacteria resided in fluid inclusions in ice-VI crystals and continued to be viable upon subsequent release to ambient pressures (0.1 MPa). Evidence of microbial viability and activity at these extreme pressures expands by an order of magnitude the range of conditions representing the habitable zone in the solar system.

The effect of three variables on shear bond strength when luting a resin inlay to dentin.

PubMed

Lee, Jae-Ik; Park, Sung-Ho H

2009-01-01

The current study evaluated the effects of three variables on the shear bond strength of indirect composite restorations to human dentin. The three variables examined included immediate dentin sealing (IDS), the thinning of dentin adhesives by air-blowing before cementation and light-curing the dentin adhesive before cementation. One-hundred and eighty cylinder composite inlays, 2 mm in diameter and 3 mm in length, were made using a Tescera ATL system (BISCO Inc). Tooth disks 2-mm thick were obtained from 90 freshly-extracted human premolars. Two indirect composite cylinders were assigned to a single tooth disk. The discs were randomly divided into six groups according to the luting methods. AdheSE (Ivoclar Vivadent) was used as the dentin-bonding agent (DBA) for all groups. In Groups 1, 2 and 3, the dentin was sealed with AdheSE before taking the impression. After priming, the adhesive was lightly air-blown, then light-cured. On the other hand, the dentin was not sealed before taking the impression in Groups 4, 5 and 6. Regarding the application of DBA before cementation, it was gently air-blown and light-cured before cementation in Groups 1 and 4; whereas, it was heavily air-blown and light-cured in Groups 2 and 5 and gently air-blown but not light-cured in Groups 3 and 6. Z-250 and Duo-Link were used as luting materials. After 24-hours of storage, the bonded inlays were subjected to a shear bond test. For each luting material, one-way ANOVA and Duncan's Multiple Range Test were used to compare the shear bond strength. Paired t-tests were also performed to compare the shear strength between the two luting materials. All the statistical tests were carried out at the 95% confidence level. In Z-250, the results of the shear bond strength were as follows: Group 1(14.90MPa) > Group 2(12.22MPa), Group 4(12.16MPa) Group 5(9.61MPa), Group 3(9.60MPa) Group 6(3.54MPa)(p<0.05). In Duo-Link, the following shear bond strengths were obtained: Group 1(14.65MPa) > Group 2(13.04MPa), Group 4(12.66MPa) > Group 5(10.10MPa) > Group 3(8.40MPa) > Group 6(2.88MPa) (p<0.05). The mean shear bond strength of Z-250 and Duo-Link were not statistically different with the exception of Group 5. In conclusion, the shear bond strength of the indirect composite restoration to dentin can be improved by dentin sealing with DBA before taking an impression, gently air drying and light curing the DBA before the luting procedure.

Effects of high hydrostatic pressure on the functional and rheological properties of the protein fraction extracted from pine nuts.

PubMed

Cao, Baiying; Fang, Li; Liu, Chunlei; Min, Weihong; Liu, Jingsheng

2018-01-01

High hydrostatic pressure treatments could increase the protein solubility (200 MPa), water holding capacity (400 MPa), and oil holding capacity (400 MPa) of pine nuts protein fractions, respectively. The exposed sufhydryl content for albumin was highest at 100 MPa while for other fractions it was 400 MPa, contrary for total sufhydryl content-generally it was at 100 MPa, except glutelin (400 MPa). Pine nuts protein fractions demonstrated the typical behavior of weak gels (G' > G″). After the treatments of high hydrostatic pressure the specific surface area of pine nuts protein particle was increased upon pressure, and the surface of protein became rough which increased the particle size. The functional groups of protein were found to be unchanged, but the characteristic peaks of pine nuts protein moved to a low-band displacement and the value of peaks was amplified accordingly to the pressure. The high hydrostatic pressure treatments were found to improve the functional properties of pine nuts protein isolates by enhancing the heat-induced gel strength of pine nuts protein isolates which make proteins more stretchable. These results suggest that high hydrostatic pressure treatments can increase the functional properties and alter the rheological properties of pine nuts protein fractions which will broaden its applications in food industry.

Strengthening Mechanisms in Nanostructured Al/SiCp Composite Manufactured by Accumulative Press Bonding

NASA Astrophysics Data System (ADS)

Amirkhanlou, Sajjad; Rahimian, Mehdi; Ketabchi, Mostafa; Parvin, Nader; Yaghinali, Parisa; Carreño, Fernando

2016-10-01

The strengthening mechanisms in nanostructured Al/SiCp composite deformed to high strain by a novel severe plastic deformation process, accumulative press bonding (APB), were investigated. The composite exhibited yield strength of 148 MPa which was 5 and 1.5 times higher than that of raw aluminum (29 MPa) and aluminum-APB (95 MPa) alloys, respectively. A remarkable increase was also observed in the ultimate tensile strength of Al/SiCp-APB composite, 222 MPa, which was 2.5 and 1.2 times greater than the obtained values for raw aluminum (88 MPa) and aluminum-APB (180 MPa) alloys, respectively. Analytical models well described the contribution of various strengthening mechanisms. The contributions of grain boundary, strain hardening, thermal mismatch, Orowan, elastic mismatch, and load-bearing strengthening mechanisms to the overall strength of the Al/SiCp microcomposite were 64.9, 49, 6.8, 2.4, 5.4, and 1.5 MPa, respectively. Whereas Orowan strengthening mechanism was considered as the most dominating strengthening mechanism in Al/SiCp nanocomposites, it was negligible for strengthening the microcomposite. Al/SiCp nanocomposite showed good agreement with quadratic summation model; however, experimental results exhibited good accordance with arithmetic and compounding summation models in the microcomposite. While average grain size of the composite reached 380 nm, it was less than 100 nm in the vicinity of SiC particles as a result of particle-stimulated nucleation mechanism.

Numeric simulation of occlusal interferences in molars restored with ultrathin occlusal veneers.

PubMed

Magne, Pascal; Cheung, Raymond

2017-01-01

Selecting material for a minimally invasive occlusal veneer reconstruction concept requires an understanding of how stresses are distributed during functional and parafunctional forces. The purpose of this in vitro study was to investigate stress distribution in a maxillary molar restored with ultrathin occlusal veneers and subjected by an antagonistic mandibular molar to clenching and working and nonworking movements. A maxillary first molar was modeled from microcomputed tomography (micro-CT) data, using medical image processing software, stereolithography editing/optimizing software, and finite element software. Simulated ultrathin occlusal veneer materials were used. The mandibular molar antagonist was a solid nondeformable geometric entity. Loads simulated clenching, working, and nonworking movements with loading of 500 N. The values of the maximum principal stress were recorded. In the clenching load situation, maximum tensile stresses were located at the occlusal veneer (52 MPa for composite resin versus 47 MPa for ceramic). In the working movement, significant additional tensile stresses were found on the palatal root (87 MPa for composite resin and 85 MPa for ceramic). In the nonworking movement, tensile stress on the ultrathin occlusal veneer increased to 118 MPa for composite resin and 143 MPa for ceramic veneers. Tensile stress peaks shifted to the mesiobuccal root (75 MPa for composite resin and 74 MPa for ceramic). The topography of stresses generated by the various occlusal interferences were clearly identified. Significant tensile stress concentrations were found within the restoration's occlusal topography and root, with the nonworking interference being the most harmful and also the most revealing of the difference between the composite resin and ceramic ultrathin occlusal veneers. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

NIR-Emitting Alloyed CdTeSe QDs and Organic Dye Assemblies: A Nontoxic, Stable, and Efficient FRET System.

PubMed

Ramírez-Herrera, Doris E; Rodríguez-Velázquez, Eustolia; Alatorre-Meda, Manuel; Paraguay-Delgado, Francisco; Tirado-Guízar, Antonio; Taboada, Pablo; Pina-Luis, Georgina

2018-04-11

In the present work, we synthesize Near Infrared (NIR)-emitting alloyed mercaptopropionic acid (MPA)-capped CdTeSe quantum dots (QDs) in a single-step one-hour process, without the use of an inert atmosphere or any pyrophoric ligands. The quantum dots are water soluble, non-toxic, and highly photostable and have high quantum yields (QYs) up to 84%. The alloyed MPA-capped CdTeSe QDs exhibit a red-shifted emission, whose color can be tuned between visible and NIR regions (608-750 nm) by controlling the Te:Se molar ratio in the precursor mixtures and/or changing the time reaction. The MPA-capped QDs were characterized by UV-visible absorption spectroscopy, fluorescence spectroscopy, transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), and zeta potential measurements. Photostability studies were performed by irradiating the QDs with a high-power xenon lamp. The ternary MPA-CdTeSe QDs showed greater photostability than the corresponding binary MPA-CdTe QDs. We report the Förster resonance energy transfer (FRET) from the MPA-capped CdTeSe QDs as energy donors and Cyanine5 NHS-ester (Cy5) dye as an energy acceptor with efficiency ( E ) up to 95%. The distance between the QDs and dye ( r ), the Förster distance ( R ₀), and the binding constant ( K ) are reported. Additionally, cytocompatibility and cell internalization experiments conducted on human cancer cells (HeLa) cells revealed that alloyed MPA-capped CdTeSe QDs are more cytocompatible than MPA-capped CdTe QDs and are capable of ordering homogeneously all over the cytoplasm, which allows their use as potential safe, green donors for biological FRET applications.

Metabolic costs imposed by hydrostatic pressure constrain bathymetric range in the lithodid crab Lithodes maja.

PubMed

Brown, Alastair; Thatje, Sven; Morris, James P; Oliphant, Andrew; Morgan, Elizabeth A; Hauton, Chris; Jones, Daniel O B; Pond, David W

2017-11-01

The changing climate is shifting the distributions of marine species, yet the potential for shifts in depth distributions is virtually unexplored. Hydrostatic pressure is proposed to contribute to a physiological bottleneck constraining depth range extension in shallow-water taxa. However, bathymetric limitation by hydrostatic pressure remains undemonstrated, and the mechanism limiting hyperbaric tolerance remains hypothetical. Here, we assess the effects of hydrostatic pressure in the lithodid crab Lithodes maja (bathymetric range 4-790 m depth, approximately equivalent to 0.1 to 7.9 MPa hydrostatic pressure). Heart rate decreased with increasing hydrostatic pressure, and was significantly lower at ≥10.0 MPa than at 0.1 MPa. Oxygen consumption increased with increasing hydrostatic pressure to 12.5 MPa, before decreasing as hydrostatic pressure increased to 20.0 MPa; oxygen consumption was significantly higher at 7.5-17.5 MPa than at 0.1 MPa. Increases in expression of genes associated with neurotransmission, metabolism and stress were observed between 7.5 and 12.5 MPa. We suggest that hyperbaric tolerance in L maja may be oxygen-limited by hyperbaric effects on heart rate and metabolic rate, but that L maja 's bathymetric range is limited by metabolic costs imposed by the effects of high hydrostatic pressure. These results advocate including hydrostatic pressure in a complex model of environmental tolerance, where energy limitation constrains biogeographic range, and facilitate the incorporation of hydrostatic pressure into the broader metabolic framework for ecology and evolution. Such an approach is crucial for accurately projecting biogeographic responses to changing climate, and for understanding the ecology and evolution of life at depth. © 2017. Published by The Company of Biologists Ltd.

Pulmonary arterial hypertension in children: diagnosis using ratio of main pulmonary artery to ascending aorta diameter as determined by multi-detector computed tomography.

PubMed

Caro-Domínguez, Pablo; Compton, Gregory; Humpl, Tilman; Manson, David E

2016-09-01

The ratio of the transverse diameter of the main pulmonary artery (MPA) to ascending aorta as determined at multi-detector CT is a tool that can be used to assess the pulmonary arterial size in cases of pulmonary arterial hypertension in children. To establish a ratio of MPA to ascending aorta diameter using multi-detector CT imaging suggestive of pulmonary arterial hypertension in children. We hypothesize that a defined ratio of MPA to ascending aorta is identifiable on multi-detector CT and that higher ratios can be used to reliably diagnose the presence of pulmonary arterial hypertension in children. We calculated the multi-detector CT ratio of MPA to ascending aorta diameter in 44 children with documented pulmonary arterial hypertension by right heart catheterization and in 44 age- and gender-matched control children with no predisposing factors for pulmonary arterial hypertension. We compared this multi-detector-CT-determined ratio with the MPA pressure in the study group, as well as with the ratio of MPA to ascending aorta in the control group. A threshold ratio value was calculated to accurately identify children with pulmonary arterial hypertension. Children with documented primary pulmonary arterial hypertension have a significantly higher ratio of MPA to ascending aorta (1.46) than children without pulmonary arterial hypertension (1.11). A ratio of 1.3 carries a positive likelihood of 34 and a positive predictive value of 97% for the diagnosis of pulmonary arterial hypertension. The pulmonary arteries were larger in children with pulmonary arterial hypertension than in a control group of normal children. A CT-measured ratio of MPA to ascending aorta of 1.3 should raise the suspicion of pulmonary arterial hypertension in children.

Apigenin prevents development of medroxyprogesterone acetate-accelerated 7,12-dimethylbenz(a)anthracene-induced mammary tumors in Sprague-Dawley rats

PubMed Central

Mafuvadze, Benford; Benakanakere, Indira; Lopez, Franklin; Besch-Williford, Cynthia; Ellersieck, Mark R.; Hyder, Salman M.

2011-01-01

The use of progestins as a component of hormone replacement therapy has been linked to an increase in breast cancer risk in postmenopausal women. We have previously shown that medroxyprogesterone acetate (MPA), a commonly administered synthetic progestin, increases production of the potent angiogenic factor vascular endothelial growth factor (VEGF) by tumor cells, leading to the development of new blood vessels and tumor growth. We sought to identify nontoxic chemicals that would inhibit progestin-induced tumorigenesis. We used a recently developed progestin-dependent mammary cancer model in which tumors are induced in Sprague-Dawley rats by 7,12-dimethylbenz(a)anthracene (DMBA) treatment. The flavonoid apigenin, which we previously found to inhibit progestin-dependent VEGF synthesis in human breast cancer cells in vitro, significantly delayed the development of, and decreased the incidence and multiplicity of, MPA-accelerated DMBA-induced mammary tumors in this animal model. Whereas apigenin decreased the occurrence of such tumors, it did not block MPA-induced intraductal and lobular epithelial cell hyperplasia in the mammary tissue. Apigenin blocked MPA-dependent increases in VEGF, and suppressed VEGF receptor-2 (VEGFR-2) but not VEGFR-1 in regions of hyperplasia. No differences were observed in estrogen or progesterone receptor levels, or the number of estrogen receptor-positive cells, within the mammary gland of MPA-treated animals administered apigenin, MPA-treated animals, and placebo treated animals. However, the number of progesterone receptor-positive cells was reduced in animals treated with MPA or MPA and apigenin compared with those treated with placebo. These findings suggest that apigenin has important chemopreventive properties for those breast cancers that develop in response to progestins. PMID:21505181

Differentiation between Wegener's granulomatosis and microscopic polyangiitis by an artificial neural network and by traditional methods.

PubMed

Linder, Roland; Orth, Isabelle; Hagen, E Christian; van der Woude, Fokko J; Schmitt, Wilhelm H

2011-06-01

To investigate the operating characteristics of the American College of Rheumatology (ACR) traditional format criteria for Wegener's granulomatosis (WG), the Sørensen criteria for WG and microscopic polyangiitis (MPA), and the Chapel Hill nomenclature for WG and MPA. Further, to develop and validate improved criteria for distinguishing WG from MPA by an artificial neural network (ANN) and by traditional approaches [classification tree (CT), logistic regression (LR)]. All criteria were applied to 240 patients with WG and 78 patients with MPA recruited by a multicenter study. To generate new classification criteria (ANN, CT, LR), 23 clinical measurements were assessed. Validation was performed by applying the same approaches to an independent monocenter cohort of 46 patients with WG and 21 patients with MPA. A total of 70.8% of the patients with WG and 7.7% of the patients with MPA from the multicenter cohort fulfilled the ACR criteria for WG (accuracy 76.1%). The accuracy of the Chapel Hill criteria for WG and MPA was only 35.0% and 55.3% (Sørensen criteria: 67.2% and 92.4%). In contrast, the ANN and CT achieved an accuracy of 94.3%, based on 4 measurements (involvement of nose, sinus, ear, and pulmonary nodules), all associated with WG. LR led to an accuracy of 92.8%. Inclusion of antineutrophil cytoplasmic antibodies did not improve the allocation. Validation of methods resulted in accuracy of 91.0% (ANN and CT) and 88.1% (LR). The ACR, Sørensen, and Chapel Hill criteria did not reliably separate WG from MPA. In contrast, an appropriately trained ANN and a CT differentiated between these disorders and performed better than LR.

Hyperventilation complaints in music performance anxiety among classical music students.

PubMed

Studer, Regina; Danuser, Brigitta; Hildebrandt, Horst; Arial, Marc; Gomez, Patrick

2011-06-01

Despite the importance of respiration and hyperventilation in anxiety disorders, research on breathing disturbances associated with hyperventilation is rare in the field of music performance anxiety (MPA, also known as stage fright). The only comparable study in this area reported a positive correlation between negative feelings of MPA and hyperventilation complaints during performance. The goals of this study were (a) to extend these previous findings to the period before performance, (b) to test whether a positive correlation also exists between hyperventilation complaints and the experience of stage fright as a problem, (c) to investigate instrument-specific symptom reporting, and (d) to confirm gender differences in negative feelings of MPA and hyperventilation complaints reported in other studies. We assessed 169 university students of classical music with a questionnaire comprising: the State-Trait Anxiety Inventory for negative feelings of MPA, the Nijmegen Questionnaire for hyperventilation complaints, and a single item for the experience of stage fright as a problem. We found a significant positive correlation between hyperventilation complaints and negative feelings of MPA before performance and a significant positive correlation between hyperventilation complaints and the experience of stage fright as a problem. Wind musicians/singers reported a significantly higher frequency of respiratory symptoms than other musicians. Furthermore, women scored significantly higher on hyperventilation complaints and negative feelings of MPA. These results further the findings of previous reports by suggesting that breathing disturbances associated with hyperventilation may play a role in MPA prior to going on stage. Experimental studies are needed to confirm whether hyperventilation complaints associated with negative feelings of MPA manifest themselves at the physiological level. Copyright © 2010 Elsevier Inc. All rights reserved.

Regional and depth variability of porcine meniscal mechanical properties through biaxial testing.

PubMed

Kahlon, A; Hurtig, M B; Gordon, K D

2015-01-01

The menisci in the knee joint undergo complex loading in-vivo resulting in a multidirectional stress distribution. Extensive mechanical testing has been conducted to investigate the tissue properties of the knee meniscus, but the testing conditions do not replicate this complex loading regime. Biaxial testing involves loading tissue along two different directions simultaneously, which more accurately simulates physiologic loading conditions. The purpose of this study was to report mechanical properties of meniscal tissue resulting from biaxial testing, while simultaneously investigating regional variations in properties. Ten left, fresh porcine joints were obtained, and the medial and lateral menisci were harvested from each joint (twenty menisci total). Each menisci was divided into an anterior, middle and posterior region; and three slices (femoral, deep and tibial layers) were obtained from each region. Biaxial and constrained uniaxial testing was performed on each specimen, and Young's moduli were calculated from the resulting stress strain curves. Results illustrated significant differences in regional mechanical properties, with the medial anterior (Young's modulus (E)=11.14 ± 1.10 MPa), lateral anterior (E=11.54 ± 1.10 MPa) and lateral posterior (E=9.0 ± 1.2 MPa) regions exhibiting the highest properties compared to the medial central (E=5.0 ± 1.22 MPa), medial posterior (E=4.16 ± 1.13 MPa) and lateral central (E=5.6 ± 1.20 MPa) regions. Differences with depth were also significant on the lateral meniscus, with the femoral (E=12.7 ± 1.22 MPa) and tibial (E=8.6 ± 1.22 MPa) layers exhibiting the highest Young's moduli. This data may form the basis for future modeling of meniscal tissue, or may aid in the design of synthetic replacement alternatives. Copyright © 2014 Elsevier Ltd. All rights reserved.

Mechanical properties of ZrB2- and HfB2-based ultra-high temperature ceramics fabricated by spark plasma sintering

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zapata-Solvas, E.; Jayaseelan, D.; Lin, Hua-Tay

2013-01-01

Flexural strengths at room temperature, at 1400 C in air and at room temperature after 1 h oxidation at 1400 C were determined for ZrB2- and HfB2-based ultra-high temperature ceramics (UHTCs). Defects caused by electrical discharge machining (EDM) lowered measured strengths significantly and were used to calculate fracture toughness via a fracture mechanics approach. ZrB2 with 20 vol.% SiC had room temperature strength of 700 90 MPa, fracture toughness of 6.4 0.6 MPa, Vickers hardness at 9.8 N load of 21.1 0.6 GPa, 1400 C strength of 400 30 MPa and room temperature strength after 1 h oxidation at 1400more » C of 678 15 MPa with an oxide layer thickness of 45 5 m. HfB2 with 20 vol.% SiC showed room temperature strength of 620 50 MPa, fracture toughness of 5.0 0.4 MPa, Vickers hardness at 9.8 N load of 27.0 0.6 GPa, 1400 C strength of 590 150 MPa and room temperature strength after 1 h oxidation at 1400 C of 660 25 MPa with an oxide layer thickness of 12 1 m. 2 wt.% La2O3 addition to UHTCs slightly reduced mechanical performance while increasing tolerance to property degradation after oxidation and effectively aided internal stress relaxation during spark plasma sintering (SPS) cooling, as quantified by X-ray diffraction (XRD). Slow crack growth was suggested as the failure mechanism at high temperatures as a consequence of sharp cracks formation during oxidation.« less

NIR-Emitting Alloyed CdTeSe QDs and Organic Dye Assemblies: A Nontoxic, Stable, and Efficient FRET System

PubMed Central

Ramírez-Herrera, Doris E.; Rodríguez-Velázquez, Eustolia; Alatorre-Meda, Manuel; Paraguay-Delgado, Francisco; Tirado-Guízar, Antonio; Taboada, Pablo; Pina-Luis, Georgina

2018-01-01

In the present work, we synthesize Near Infrared (NIR)-emitting alloyed mercaptopropionic acid (MPA)-capped CdTeSe quantum dots (QDs) in a single-step one-hour process, without the use of an inert atmosphere or any pyrophoric ligands. The quantum dots are water soluble, non-toxic, and highly photostable and have high quantum yields (QYs) up to 84%. The alloyed MPA-capped CdTeSe QDs exhibit a red-shifted emission, whose color can be tuned between visible and NIR regions (608–750 nm) by controlling the Te:Se molar ratio in the precursor mixtures and/or changing the time reaction. The MPA-capped QDs were characterized by UV-visible absorption spectroscopy, fluorescence spectroscopy, transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDS), and zeta potential measurements. Photostability studies were performed by irradiating the QDs with a high-power xenon lamp. The ternary MPA-CdTeSe QDs showed greater photostability than the corresponding binary MPA-CdTe QDs. We report the Förster resonance energy transfer (FRET) from the MPA-capped CdTeSe QDs as energy donors and Cyanine5 NHS-ester (Cy5) dye as an energy acceptor with efficiency (E) up to 95%. The distance between the QDs and dye (r), the Förster distance (R0), and the binding constant (K) are reported. Additionally, cytocompatibility and cell internalization experiments conducted on human cancer cells (HeLa) cells revealed that alloyed MPA-capped CdTeSe QDs are more cytocompatible than MPA-capped CdTe QDs and are capable of ordering homogeneously all over the cytoplasm, which allows their use as potential safe, green donors for biological FRET applications. PMID:29641435

Viscoelastic properties of human and bovine articular cartilage: a comparison of frequency-dependent trends.

PubMed

Temple, Duncan K; Cederlund, Anna A; Lawless, Bernard M; Aspden, Richard M; Espino, Daniel M

2016-10-06

The purpose of this study was to compare the frequency-dependent viscoelastic properties of human and bovine cartilage. Full-depth cartilage specimens were extracted from bovine and human femoral heads. Using dynamic mechanical analysis, the viscoelastic properties of eight bovine and six human specimens were measured over the frequency range 1 Hz to 88 Hz. Significant differences between bovine and human cartilage viscoelastic properties were assessed using a Mann-Whitney test (p < 0.05). Throughout the range of frequencies tested and for both species, the storage modulus was greater than the loss modulus and both were frequency-dependent. The storage and loss moduli of all human and bovine cartilage specimens presented a logarithmic relationship with respect to frequency. The mean human storage modulus ranged from 31.9 MPa to 43.3 MPa, while the mean bovine storage modulus ranged from 54.0 MPa to 80.5 MPa; bovine storage moduli were 1.7 to 1.9 times greater than the human modulus. Similarly, the loss modulus of bovine cartilage was 2.0 to 2.1 times greater than human. The mean human loss modulus ranged from 5.3 MPa to 8.5 MPa while bovine moduli ranged from 10.6 MPa to 18.1 MPa. Frequency-dependent viscoelastic trends of bovine articular cartilage were consistent with those of human articular cartilage; this includes a similar frequency dependency and high-frequency plateau. Bovine cartilage was, however, 'stiffer' than human by a factor of approximately 2. With these provisos, bovine articular cartilage may be a suitable dynamic model for human articular cartilage.

Effects of the ultra-high pressure on structure and α-glucosidase inhibition of polysaccharide from Astragalus.

PubMed

Zhu, Zhen-Yuan; Luo, You; Dong, Guo-Ling; Ren, Yuan-Yuan; Chen, Li-Jing; Guo, Ming-Zhu; Wang, Xiao-Ting; Yang, Xue-Ying; Zhang, Yongmin

2016-06-01

A novel homogeneous polysaccharide fraction (APS) was extracted from Astragalus by hot water and purified by Sephadex G-100 and G-75 column. Its molecular weight was 693kDa. APS and APS with ultra-high pressure treatment exhibited significant inhibitory abilities on a-glucosidase, inhibition rate from high to low in order was 400MPa-APS, 300MPa-APS, 500MPa-APS and APS. The inhibition ​percentage of 400MPa-APS (1.5mg/mL) was 49% (max.). This suggested that the inhibitory activity of APS on a-glucosidase was improved by ultra-high pressure treatment. FT-IR, SEM, CD spectra, atomic force microscope and Congo red test analysis of APS and 400MPa-APS showed ultra-high pressure treatment didn't change the preliminary structure but had an effect on its advanced structure. Copyright © 2016 Elsevier B.V. All rights reserved.

Advanced thermoplastic resins, phase 2

NASA Technical Reports Server (NTRS)

Brown, A. M.; Hill, S. G.; Falcone, A.

1991-01-01

High temperature structural resins are required for use on advanced aerospace vehicles as adhesives and composite matrices. NASA-Langley developed polyimide resins were evaluated as high temperature structural adhesives for metal to metal bonding and as composite matrices. Adhesive tapes were prepared on glass scrim fabric from solutions of polyamide acids of the semicrystalline polyimide LARC-CPI, developed at the NASA-Langley Research Center. Using 6Al-4V titanium adherends, high lap shear bond strengths were obtained at ambient temperature (45.2 MPa, 6550 psi) and acceptable strengths were obtained at elevated temperature (14.0 MPa, 2030 psi) using the Pasa-Jell 107 conversion coating on the titanium and a bonding pressure of 1.38 MPa (200 psi). Average zero degree composite tensile and compressive strengths of 1290 MPa (187 ksi) and 883 MPa (128 ksi) respectively were obtained at ambient temperature with unsized AS-4 carbon fiber reinforcement.

Aqueous synthesis of L-cysteine and mercaptopropionic acid co-capped ZnS quantum dots with dual emissions

NASA Astrophysics Data System (ADS)

Ren, Yingkun; Wang, Yongbo; Yang, Min; Liu, Enzhou; Hu, Xiaoyun; Zhang, Xu; Fan, Jun

2018-07-01

In this paper, L-cysteine (L-cys) and mercaptopropionic acid (MPA) co-capped ZnS quantum dots (QDs) with dual emissions have been successfully synthesized by a one-pot aqueous-phase synthesis method. The intensities of the dual emissions could be controlled by regulating the molar ratio of L-cys to MPA, and the fluorescence color also turned from blue to yellow accordingly. The relationship between the ligands and fluorescence was investigated and the results indicated that L-cys could cause two emissions and MPA improved the emission intensity. In addition, the L-cys-MPA co-capped ZnS QDs showed high photostability under UV irradiation. Therefore, the L-cys-MPA co-capped ZnS QDs, which show the dual emissions and tunable emission intensities, have great potentials for use in ratiometric fluorescence sensors and multicolor bioimaging.

Mycophenolate fetal toxicity and risk evaluation and mitigation strategies.

PubMed

Kim, M; Rostas, S; Gabardi, S

2013-06-01

The mycophenolic acid (MPA) preparations are one of the most commonly used immunosuppressants in the United States. However, these agents carry a black box warning regarding their use during pregnancy due to an association with increased risk of miscarriage and congenital defects. To ensure that the benefits of MPA outweigh the risks, the Food and Drug Administration (FDA) required all manufacturers of MPA products to propose risk evaluation and mitigation strategies (REMS). Four years after initially calling for proposals, the FDA approved a single shared REMS system in September 2012. The elements of the MPA REMS include a medication guide and elements to assure safe use (ETASU). The medication guide, which was previously FDA-approved in 2008, should continue to be distributed to patients, and the ETASU requires physicians to complete training and obtain patient signatures on the "Patient-Prescriber Acknowledgement Form." A single, national, voluntary pregnancy registry is available, and pregnant patients should be encouraged to participate. Although the impact of the MPA REMS on clinical practice is not clear, it is a step toward increasing the understanding of fetal risks with MPA products among patients and possibly practitioners. © Copyright 2013 The American Society of Transplantation and the American Society of Transplant Surgeons.

Music performance anxiety-part 2. a review of treatment options.

PubMed

Brugués, Ariadna Ortiz

2011-09-01

Music performance anxiety (MPA) affects many individuals independent of age, gender, experience, and hours of practice. In order to prevent MPA from happening or to alleviate it when it occurs, a review of the literature about its prevention and treatment was done. Forty-four articles, meeting evidence-based medicine (EBM) criteria, were identified and analyzed. Performance repertoire should be chosen based on the musician's skill level, and it should be practiced to the point of automaticity. Because of this, the role of music teachers is essential in preventing MPA. Prevention is the most effective method against MPA. Several treatments (psychological as well as pharmacological) have been studied on subjects in order to determine the best treatment for MPA. Cognitive-behavioral therapy (CBT) seems to be the most effective, but further investigation is desired. Some musicians, in addition to CBT, also take beta-blockers; however, these drugs should only be prescribed occasionally after analyzing the situation and considering the contraindications and possible side effects. Despite these conclusions, more randomized studies with larger, homogeneous groups of subjects would be desirable (according to the EBM criteria), as well as support for the necessity of both MPA prevention and optimized methods of treatment when it does occur.

Impact of pH and application time of meta-phosphoric acid on resin-enamel and resin-dentin bonding.

PubMed

Cardenas, A F M; Siqueira, F S F; Bandeca, M C; Costa, S O; Lemos, M V S; Feitora, V P; Reis, A; Loguercio, A D; Gomes, J C

2018-02-01

To evaluate the immediate microshear resin-enamel bond strength (μSBS) and the immediate and 6-month microtensile bond strength (μTBS) and nanoleakage (NL) of the adhesive interface performed by different pHs of 40% meta-phosphoric acid (MPA) were compared with conventional 37% ortho-phosphoric acid (OPA) under different application times. Additionally, the enamel etching patterns were evaluated and the chemical/morphological changes induced by these differents groups were evaluated. One hundred and ninety-eight extracted human molars were randomly assigned into experimental groups according to the combination of independent variables: Acid [37% ortho-phosphoric acid (OPA), 40% meta-phosphoric acid (MPA) at pHs of: 0.5, 1 and 2] and Application Time [7, 15 and 30s]. Enamel-bond specimens were prepared and tested under μSBS. Resin-dentin beams were tested under μTBS tested immediately or after 6-months of water storage. Nanoleakage was evaluated using bonded-beams of each tooth/time-period. Enamel etching pattern and chemical and ultra-morphology analyses were also performed. The μSBS (MPa) data were subjected to a two-way repeated measures ANOVA (Acid vs. Application time). For μTBS, Acid vs application time vs storage time data were subjected to three-way ANOVA and Tukey's test (α = 0.05). MPA pH 0.5 showed μTBS similar to OPA, independently of the application time on enamel (p>0.05) or dentin (p>0.05). OPA provided higher nanoleakage values than MPA (p = 0.003). Significant decreases in TBS and increases in NL were only observed for OPA after 6 months (p = 0.001). An increase in the application time resulted in a more pronounced etching pattern for MPA. Chemical analysis showed that dentin demineralized by MPA depicted peaks of brushite and octacalcium phosphate. MPA exposed less collagen than OPA. However, optimal results for MPA were dependent on pH/application time. The use of 40% meta-phosphoric acid with a pH of 0.5 is an alternative acid-etching agent for dentin and enamel bonding. Furthermore, the use of MPA preserves the resin-dentin interface over a 6-months period, due to presence of brushite and octacalcium phosphate and a reduced demineralization pattern. Copyright © 2017 Elsevier Ltd. All rights reserved.

Bonding of composite resins to PEEK: the influence of adhesive systems and air-abrasion parameters.

PubMed

Stawarczyk, Bogna; Taufall, Simon; Roos, Malgorzata; Schmidlin, Patrick R; Lümkemann, Nina

2018-03-01

The objective of the study was to investigate the tensile bond strength (TBS) to polyaryletheretherketone (PEEK) after different pretreatment and conditioning methods. Four hundred PEEK specimens were fabricated and allocated to the following air-abrasion methods (n 1  = 80/pretreatment): (i) 50 μm Al 2 O 3 (0.05 MPa); (ii) 50 μm Al 2 O 3 (0.35 MPa); (iii) 110 μm Al 2 O 3 (0.05 MPa); (iv) 110 μm Al 2 O 3 (0.35 MPa); and (v) Rocatec 110 μm (0.28 MPa). These pretreatments were combined with the following conditioning methods (n 2  = 20/pretreatment/conditioning): (a) visio.link (VL); (b) Monobond Plus/Heliobond (MH); (c) Scotchbond Universal (SU); and (d) dialog bonding fluid (DB). After veneering of all specimens with dialog occlusal and aging (28 days H 2 O, 37 °C + 20,000 thermal cycles, 5/55 °C), TBS was measured. Data was analysed using Kaplan-Meier survival analysis with Breslow-Gehan test and Cox-regressions. The major impact on TBS showed the conditioning, followed by the air-abrasion-pressure, while the grain size of the air-abrasion powder did not show any effect. Specimens air-abraded at 0.35 MPa showed the highest survival rates. However, within VL groups, this observation was not statistically significant. Within MH groups, pretreatment using 110 μm Al 2 O 3 and 0.05 MPa resulted in higher survival rates compared to groups treated with 50 and 110 μm Al 2 O 3 using a pressure of 0.35 MPa. The use of VL showed the highest survival rates between the adhesive systems and the TBS values higher than 25 MPa independent of the pretreatment method. As an exception, only VL showed significantly higher survival rates when compared to MH. The adequate choice of the adhesive system and higher pressures improved the TBS between PEEK and veneering resin composite. The particle size had no major impact. According to this study, best veneering of PEEK with dialog occlusal can be achieved by conditioning with visio.link in combination with the pretreatment of airborne particle abrasion at a pressure of 0.35 MPa.

Hydrogen-alkali exchange between silicate melts and two-phase aqueous mixtures: an experimental investigation

NASA Astrophysics Data System (ADS)

Williams, Thomas J.; Candela, Philip A.; Piccoli, Philip M.

Experiments were performed in the three-phase system high-silica rhyolite melt + low-salinity aqueous vapor + hydrosaline brine, to investigate the exchange equilibria for hydrogen, potassium, and sodium in magmatic-hydrothermal systems at 800 °C and 100 MPa, and 850 °C and 50 MPa. The Kaqm/meltH,Na and Kaqm/meltH,K for hydrogen-sodium exchange between a vapor + brine mixture and a silicate melt are inversely proportional to the total chloride concentration (ΣCl) in the vapor + brine mixture indicating that HCl/NaCl and HCl/KCl are higher in the low-salinity aqueous vapor relative to high-salinity brine. The equilibrium constants for vapor/melt and brine/melt exchange were extracted from regressions of Kaqm/meltH,Na and Kaqm/meltH,K versus the proportion of aqueous vapor relative to brine in the aqueous mixture (Faqv) at P and T, expressed as a function of ΣCl. No significant pressure effect on the empirically determined exchange constants was observed for the range of pressures investigated. Model equilibrium constants are: Kaqv/meltH,Na(vapor/melt)=26(+/-1.3) at 100 MPa (800 °C), and 19( +/- 7.0) at 50 MPa (850 °C) Kaqv/meltH,K=14(+/-1.1) at 100 MPa (800 °C), and 24(+/-12) at 50 MPa (850 °C) Kaqb/meltH,b(brine/melt)= 1.6(+/-0.7) at 100 MPa (800 °C), and 3.9(+/-2.3) at 50 MPa (850 °C) and Kaqb/meltH,K=2.7(+/-1.2) at 100 MPa (800 °C) and 3.8(+/-2.3) at 50 MPa (850 °C). Values for Kaqv/meltH,K and Kaqb/meltH,K were used to calculate KCl/HCl in the aqueous vapor and brine as a function of melt aluminum saturation index (ASI: molar Al2O3/(K2O+Na2O+CaO) and pressure. The model log KCl/HCl values show that a change in melt ASI from peraluminous (ASI = 1.04) to moderately metaluminous (ASI = 1.01) shifts the cooling pathway (in temperature-log KCl/HCl space) of the aqueous vapor toward the andalusite+muscovite+K-feldspar reaction point.

Differential Sensitivities of Fast- and Slow-Cycling Cancer Cells to Inosine Monophosphate Dehydrogenase 2 Inhibition by Mycophenolic Acid

PubMed Central

Chen, Kan; Cao, Wanlu; Li, Juan; Sprengers, Dave; Hernanda, Pratika Y; Kong, Xiangdong; van der Laan, Luc JW; Man, Kwan; Kwekkeboom, Jaap; Metselaar, Herold J; Peppelenbosch, Maikel P; Pan, Qiuwei

2015-01-01

As uncontrolled cell proliferation requires nucleotide biosynthesis, inhibiting enzymes that mediate nucleotide biosynthesis constitutes a rational approach to the management of oncological diseases. In practice, however, results of this strategy are mixed and thus elucidation of the mechanisms by which cancer cells evade the effect of nucleotide biosynthesis restriction is urgently needed. Here we explored the notion that intrinsic differences in cancer cell cycle velocity are important in the resistance toward inhibition of inosine monophosphate dehydrogenase (IMPDH) by mycophenolic acid (MPA). In short-term experiments, MPA treatment of fast-growing cancer cells effectively elicited G0/G1 arrest and provoked apoptosis, thus inhibiting cell proliferation and colony formation. Forced expression of a mutated IMPDH2, lacking a binding site for MPA but retaining enzymatic activity, resulted in complete resistance of cancer cells to MPA. In nude mice subcutaneously engrafted with HeLa cells, MPA moderately delayed tumor formation by inhibiting cell proliferation and inducing apoptosis. Importantly, we developed a lentiviral vector–based Tet-on label-retaining system that enables to identify, isolate and functionally characterize slow-cycling or so-called label-retaining cells (LRCs) in vitro and in vivo. We surprisingly found the presence of LRCs in fast-growing tumors. LRCs were superior in colony formation, tumor initiation and resistance to MPA as compared with fast-cycling cells. Thus, the slow-cycling compartment of cancer seems predominantly responsible for resistance to MPA. PMID:26467706

Human Resource Management and Army Recruiting. Analysis of Policy Options

DTIC Science & Technology

2006-01-01

Forces Qualification Test ARISS -MPA Army Recruiting Information Support System— Mission Production Awards CMF Career Management Field DA Department of...called the Army Recruiting Information Support System—Mission Production Awards ( ARISS -MPA). 2 Appendix C provides more detailed information about these...Management and Army Recruiting Table B.1 Data Sources Contracts Army Recruiting Information Support System—Mission Production Awards ( ARISS -MPA), United

A limited sampling model for estimation of total and unbound mycophenolic acid (MPA) area under the curve (AUC) in hematopoietic cell transplantation (HCT).

PubMed

Ng, Juki; Rogosheske, John; Barker, Juliet; Weisdorf, Daniel; Jacobson, Pamala A

2006-06-01

Renal transplant patients with suboptimal mycophenolic acid (MPA) areas under the curves (AUCs) are at greater risk of acute rejection. In hematopoietic cell transplantation, a low MPA AUC is also associated with a higher incidence of acute graft versus host disease. Therefore, a limited sampling model was developed and validated to simultaneously estimate total and unbound MPA AUC0-12 in hematopoietic cell transplantation patients. Intensive pharmacokinetic sampling was performed at steady state between days 3 to 7 posttransplant in 73 adult subjects while receiving prophylactic mycophenolate mofetil 1 g per 12 hours orally or intravenously plus cyclosporine. Total and unbound MPA plasma concentrations were measured, and total and unbound AUC0-12 was determined using noncompartmental analysis. Regression analysis was then performed to build IV and PO, total and unbound AUC0-12 models from the first 34 subjects. The predictive performance of these models was tested in the next 39 subjects. Trough concentrations poorly estimate observed total and unbound AUC0-12 (r<0.48). A model with 3 concentrations (2-, 4-, and 6-hour post start of infusion) best estimated observed total and unbound AUC0-12 after IV dosing (r>0.99). Oral total and unbound AUC0-12 was more difficult to estimate and required at least 4 concentrations (0-, 1-, 2-, and 6-hour post dose) in the model (r>0.85). The predictive performance of the final models was good. Eighty-three percent of IV and 70% of PO AUC0-12 predictions fell within +/-20% of the observed values without significant bias. Trough MPA concentrations do not accurately describe MPA AUC0-12. Three intravenous (2-, 4-, 6-hour post start of infusion) or 4 oral (0-, 1-, 2-, and 6-hour post dose) MPA plasma concentrations measured over a 12-hour dosing interval will estimate the total and unbound AUC0-12 nearly as well as intensive pharmacokinetic sampling with good precision and low bias. This approach simplifies AUC0-12 targeting of MPA post hematopoietic cell transplantation.

Efficiency of pretreatment of aqueous samples using a macroporous strong anion-exchange resin on the determination of nerve gas hydrolysis products by gas chromatography-mass spectrometry after tert.-butyldimethylsilylation.

PubMed

Kataoka, M; Tsuge, K; Seto, Y

2000-09-08

A pretreatment procedure, using a macroporous strong anion-exchange resin (MSA) has been established for the determination of nerve gas hydrolysis products by gas chromatography-mass spectrometry (GC-MS) after tert.-butyldimethylsilyl (TBDMS) derivatization. Aqueous solutions of methylphosphonic acid (MPA) and three alkyl methylphosphonic acids (AMPAs) (ethyl, isopropyl and pinacolyl methylphosphonic acid), were retained on the MSA column, and then quantitatively eluted with 0.1 M hydrochloric acid. The neutralized column eluate was dried, and MPA and AMPAs were derivatized with N-methyl-N-(tert.-butyldimethylsilyl)-trifluoroacetamide and analyzed by GC-MS. The column eluate was also analyzed in order to determine the exact hydrolysis product levels by capillary electrophoresis using borate and benzoate buffer (pH 6). The MSA pretreatment was examined for the clean-up of aqueous extracts of three types of soils and an aqueous solution containing 10% sucrose, which is regarded as model for a typical soft drink, after spiking with MPA and AMPAs. MPA and AMPAs were quantitatively recovered in the MSA eluate fraction from those samples, except for MPA from volcanic acid and alluvial soils. The yields of TBDMS derivatives were remarkably improved, compared with for which no pretreatment was used and also for those in which a strong cation-exchange resin was used. The achieved detection limits of MPA and AMPAs ranged from 0.12 to 0.18 microg/g of soil (S/N=3). The established MSA method was applied to the pretreatment of spiked sea water, two types of beverages, Pepsi Cola and canned coffee. Although the yields of TBDMS derivatives of MPA and AMPAs in sea water (in a range between 44 and 96%) and AMPAs in Pepsi Cola (in a range between 58 and 92%) were rather high, those for MPA in the Pepsi Cola (27%) and those for MPA and AMPAs in the canned coffee (in a range between 5 and 17%) were low.

A Coupled Creep-Plasticity Model for Residual Stress Relaxation of a Shot-Peened Nickel-Base Superalloy

DTIC Science & Technology

2007-05-01

4 1e+5 1e+ 6 1000MPa... 6 1e-5 1e- 4 1e-3 1e-2 1e-1 1e-1 1e+0 1e+1 1e+2 1e+3 1e+ 4 1e+5 1e+ 6 1000MPa 900MPa 800MPa C re ep R at e (/s ) Creep Time (s) 0% Prestrain, 650°C...increase in strain rate. The change in deformation response is significant even for small plastic strains. 1e-9 1e-8 1e-7 1e- 6 1e-5 1e- 4 1e-3

Marine protected areas in Costa Rica: How do artisanal fishers respond?

PubMed

Madrigal-Ballestero, Róger; Albers, Heidi J; Capitán, Tabaré; Salas, Ariana

2017-11-01

Costa Rica is considering expanding their marine protected areas (MPAs) to conserve marine resources. Due to the importance of households' responses to an MPA in defining the MPA's ecological and economic outcomes, this paper uses an economic decision framework to interpret data from near-MPA household surveys to inform this policy discussion. The model and data suggest that the impact of expanding MPAs relies on levels of enforcement and on-shore wages. If larger near-shore MPAs can produce high wages through increased tourism, MPA expansions could provide ecological benefits with low burdens to communities. Due to distance costs and gear investments, however, MPAs farther off-shore may place high burdens on off-shore fishers.

Music performance anxiety in opera singers.

PubMed

Spahn, Claudia; Echternach, Matthias; Zander, Mark F; Voltmer, Edgar; Richter, Bernhard

2010-12-01

Music performance anxiety (MPA) represents a high challenge every vocal performer has to meet. MPA can be defined on a continuum going from a low to a high level. MPA and its phenomena can be considered in terms of four levels: affect, cognition, behaviour, and physiology. A study carried out on seven opera singers and two instrumentalists during performance situations showed highly elevated values for the performers' heart rate and blood pressure. This study, as several others, yielded no clear evidence pointing to a correspondence between the level of anxiety and of physiological arousal. At the end of the article a multimodal approach to the treatment of MPA is illustrated consisting of different psychotherapeutic and body-oriented methods.

Structure and Activity Changes of Phytohemagglutinin from Red Kidney Bean (Phaseolus vulgaris) Affected by Ultrahigh-Pressure Treatments.

PubMed

Lu, Yunjun; Liu, Cencen; Zhao, Mouming; Cui, Chun; Ren, Jiaoyan

2015-11-04

Phytohemagglutin (PHA), purified from red kidney beans (Phaseolus vulgaris) by Affi-Gel blue affinity chromatography, was subjected to ultrahigh-pressure (UHP) treatment (150, 250, 350, and 450 MPa). The purified PHA lost its hemagglutination activity after 450 MPa treatment and showed less pressure tolerance than crude PHA. However, the saccharide specificity and α-glucosidase inhibition activity of the purified PHA did not change much after UHP treatment. Electrophoresis staining by periodic acid-Schiff (PAS) manifested that the glycone structure of purified PHA remained stable even after 450 MPa pressure treatment. However, electrophoresis staining by Coomassie Blue as well as circular dichroism (CD) and differential scanning calorimetry (DSC) assay proved that the protein unit structure of purified PHA unfolded when treated at 0-250 MPa but reaggregates at 250-450 MPa. Therefore, the hemagglutination activity tends to be affected by the protein unit structure, while the stability of the glycone structure contributed to the remaining α-glucosidase inhibition activity.

Relationships Among Performance Anxiety, Agari Experience, and Depressive Tendencies in Japanese Music Students.

PubMed

Bannai, Kurara; Kase, Takayoshi; Endo, Shintaro; Oishi, Kazou

2016-12-01

The purpose of this study was to investigate the relationships among anxiety prior to actual performance (music performance anxiety, MPA), mental and physical negative responses during performance (agari), and depressive tendencies in Japanese college students majoring in music. Participants were 171 music majors (33 males, 138 females, 20.6±1.7 yrs). They rated the degree of self-perceived MPA before their performance on a scale ranging from 0-100%. The Features of Agari Experience Questionnaire was used to assess agari response levels during standard performances, and the Japanese version of the Center for Epidemiologic Studies Depression Scale (CESD) was used to measure depressive tendencies. Path analysis showed that MPA levels were positively related to agari scores, which were positively related to CES-D scores. Mediation analysis found a significant indirect effect of MPA scores on CES-D scores via the agari scores. These results suggest that MPA first occurs before an actual music performance and evokes agari, which in turn may cause an increase in depressive tendencies.

Do cytostatic drugs reach drinking water? The case of mycophenolic acid.

PubMed

Franquet-Griell, Helena; Ventura, Francesc; Boleda, M Rosa; Lacorte, Silvia

2016-01-01

Mycophenolic acid (MPA) has been identified as a new river contaminant according to its wide use and high predicted concentration. The aim of this study was to monitor the impact of MPA in a drinking water treatment plant (DWTP) that collects water downstream Llobregat River (NE Spain) in a highly densified urban area. During a one week survey MPA was recurrently detected in the DWTP intake (17-56.2 ng L(-1)). The presence of this compound in river water was associated to its widespread consumption (>2 tons in 2012 in Catalonia), high excretion rates and low degradability. The fate of MPA in waters at each treatment step of the DWTP was analyzed and complete removal was observed after pretreatment with chlorine dioxide. So far, MPA has not been described as water contaminant and its presence associated with its consumption in anticancer treatments is of relevance to highlight the importance of monitoring this compound. Copyright © 2015 Elsevier Ltd. All rights reserved.

The YPR153W gene is essential for the pressure tolerance of tryptophan permease Tat2 in the yeast Saccharomyces cerevisiae

NASA Astrophysics Data System (ADS)

Kurosaka, Goyu; Abe, Fumiyoshi

2018-01-01

In the yeast Saccharomyces cerevisiae, hydrostatic pressure at 25 MPa is known to be nonlethal but significantly impairs the uptake of tryptophan by the permease Tat2, thereby inhibiting the growth of strains that require tryptophan from the medium. Here, we found that the lack of the YPR153W gene, so far poorly characterized for its role in yeast, caused a serious adverse effect on the growth at 10-25 MPa in the strain that required tryptophan. Deletion for YPR153W resulted in an increased rate of pressure-induced degradation of Tat2, suggesting that Tat2 is destabilized in the YPR153W deletion mutant at 25 MPa. Overexpression of the TAT2 gene enabled the deletion mutant to grow at 25 MPa. These results suggest that Ypr153w is essential for the stability and proper transport function of Tat2 under pressure at 10-25 MPa.

Evaluation on Compression Properties of Different Shape and Perforated rHDPE in Concrete Structures

NASA Astrophysics Data System (ADS)

Yuhazri, M. Y.; Hafiz, K. M.; Myia, Y. Z. A.; Jia, C. P.; Sihombing, H.; Sapuan, S. M.; Badarulzaman, N. A.

2017-10-01

The purpose of this study was to develop a concrete structure by incorporating waste HDPE plastic as the main reinforcement material and cement as the matrix via standard casting technique. There are eight different shapes of rHDPE reinforcing structure were used to investigate the compression properties of produced concrete composites. Experimental result shown that the highest shape in compressive strength of rHDPE reinforcing structure were the concrete with the addition of X-perforated beam (18.22 MPa), followed by X-beam (17.7 MPa), square perforated tube (17.54 MPa), round tube (17.42 MPa) and round perforated tube (16.69 MPa). In terms of their compressive behavior, the average concrete containing rHDPE reinforcement was successfully improved by 6 % of the mechanical characteristic compared to control concrete. It is shown that the addition of waste plastic as reinforcement structure can provide better compressive strength based on their shape and pattern respectively.

Analysis of the Effect of Injection Pressure on Ignition Delay and Combustion Process of Biodiesel from Palm Oil, Algae and Waste Cooking Oil

NASA Astrophysics Data System (ADS)

Irham Anas, Mohd; Khalid, Amir; Hakim Zulkifli, Fathul; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin

2017-10-01

Biodiesel is a domestically produced, renewable fuel that can be manufactured from vegetable oils, animal fats, or recycled restaurant grease for use in diesel engines. The objective of this research is investigation the effects of the variant injection pressure on ignition delay and emission for different biodiesel using rapid compression machine. Rapid Compression Machine (RCM) is used to simulate a single compression stroke of an internal combustion engine as a real engine. Four types of biodiesel which are waste cooking oil, crude palm oil, algae and jatropha were tested at injection pressure of 80 MPa, 90 MPa and 130 MPa under constant ambient temperature at 950 K. Increased in injection pressure resulted shorter ignition delay proven by WCO5 which decreased from 1.3 ms at 80 MPa to 0.7 ms at 130 MPa. Meanwhile, emission for CO2 increased due to better fuel atomization for fuel-air mixture formation lead to completed combustion.

Performance of raw bovine meat preservation by hyperbaric storage (quasi energetically costless) compared to refrigeration.

PubMed

Freitas, Paulo; Pereira, Sofia A; Santos, Mauro D; Alves, Susana P; Bessa, Rui J B; Delgadillo, Ivonne; Saraiva, Jorge A

2016-11-01

Hyperbaric storage at room temperature (without temperature control) of raw bovine meat was studied and compared to refrigeration. Samples were first stored for 12h at 50, 100 and 150MPa, and in a second set of experiments, for a longer period of 10days at 50MPa. For the 12h storage, refrigeration and 50MPa had a similar microbial growth inhibition effect and, at 100 and 150MPa an additional microbial inactivation effect was found. For the longer experiment (10days at 50MPa) results pointed for a shelf-life increase of raw beef compared to samples stored under refrigeration. For both tests (12h and 10days) samples preserved under pressure showed no detrimental effect on physicochemical parameters comparatively to the initial and refrigerated samples. These results indicate that hyperbaric storage at room temperature not only allows high energy savings, but additionally has potential to extend the shelf-life of a perishable food product compared to refrigeration. Copyright © 2016 Elsevier Ltd. All rights reserved.

Fate of Pup inside the Mycobacterium Proteasome Studied by in-Cell NMR

PubMed Central

Maldonado, Andres Y.; Burz, David S.; Reverdatto, Sergey; Shekhtman, Alexander

2013-01-01

The Mycobacterium tuberculosis proteasome is required for maximum virulence and to resist killing by the host immune system. The prokaryotic ubiquitin-like protein, Pup-GGE, targets proteins for proteasome-mediated degradation. We demonstrate that Pup-GGQ, a precursor of Pup-GGE, is not a substrate for proteasomal degradation. Using STINT-NMR, an in-cell NMR technique, we studied the interactions between Pup-GGQ, mycobacterial proteasomal ATPase, Mpa, and Mtb proteasome core particle (CP) inside a living cell at amino acid residue resolution. We showed that under in-cell conditions, in the absence of the proteasome CP, Pup-GGQ interacts with Mpa only weakly, primarily through its C-terminal region. When Mpa and non-stoichiometric amounts of proteasome CP are present, both the N-terminal and C-terminal regions of Pup-GGQ bind strongly to Mpa. This suggests a mechanism by which transient binding of Mpa to the proteasome CP controls the fate of Pup. PMID:24040288

Mitigating Stress Waves Using Nanofoams and Nanohoneycombs

DTIC Science & Technology

2014-04-16

In the following sections, we present our work in chronological order. 3 1. TWO-PARAMETER STUDY ON SILICA NANOFOAMS 1.1 Preparation...and Characterization of Silica Nanofoams Following the work in the last period of performance, we performed a systematic study on silica nanofoam...12.98MPa Peak value of transmission pulse: 5.32MPa Normalized peak value: 0.410 Pressure reduction: 0.02 MPa 19 2. SINGLE-PARAMETER STUDY ON

Study of High Temperature Failure Mechanism in Ceramics

DTIC Science & Technology

1992-01-01

characteristics of the glass-ceramic are presented in Figure 9 for K = 0.95 MPaI -at 750"C and in Figure 10 forK = 0.59 MPa’mat 775"C. Results I presented in these...at K = 0.59 MPai1- and Figure 12(b) showing the removal of those cavities by sintering at K = 0.5 MPaI -. The near-tip region where creep cavities

Further Theoretical Insight into the Mechanical Properties of Polycaprolactone Loaded with Organic–Inorganic Hybrid Fillers

PubMed Central

Maietta, Saverio; Russo, Teresa; De Santis, Roberto; Ronca, Dante; Riccardi, Filomena; Martorelli, Massimo; Gloria, Antonio

2018-01-01

Experimental/theoretical analyses have already been performed on poly(ε-caprolactone) (PCL) loaded with organic–inorganic fillers (PCL/TiO2 and PCL/ZrO2) to find a correlation between the results from the small punch test and Young’s modulus of the materials. PCL loaded with Ti2 (PCL = 12, TiO2 = 88 wt %) and Zr2 (PCL = 12, ZrO2 = 88 wt %) hybrid fillers showed better performances than those obtained for the other particle composition. In this context, the aim of current research is to provide further insight into the mechanical properties of PCL loaded with sol–gel-synthesized organic–inorganic hybrid fillers for bone tissue engineering. For this reason, theoretical analyses were performed by the finite element method. The results from the small punch test and Young’s modulus of the materials were newly correlated. The obtained values of Young’s modulus (193 MPa for PCL, 378 MPa for PCL/Ti2 and 415 MPa for PCL/Zr2) were higher than those obtained from a previous theoretical modelling (144 MPa for PCL, 282 MPa for PCL/Ti2 and 310 MPa for PCL/Zr2). This correlation will be an important step for the evaluation of Young’s modulus, starting from the small punch test data. PMID:29466299

Further Theoretical Insight into the Mechanical Properties of Polycaprolactone Loaded with Organic-Inorganic Hybrid Fillers.

PubMed

Maietta, Saverio; Russo, Teresa; Santis, Roberto De; Ronca, Dante; Riccardi, Filomena; Catauro, Michelina; Martorelli, Massimo; Gloria, Antonio

2018-02-21

Experimental/theoretical analyses have already been performed on poly(ε-caprolactone) (PCL) loaded with organic-inorganic fillers (PCL/TiO₂ and PCL/ZrO₂) to find a correlation between the results from the small punch test and Young's modulus of the materials. PCL loaded with Ti2 (PCL = 12, TiO₂ = 88 wt %) and Zr2 (PCL = 12, ZrO₂ = 88 wt %) hybrid fillers showed better performances than those obtained for the other particle composition. In this context, the aim of current research is to provide further insight into the mechanical properties of PCL loaded with sol-gel-synthesized organic-inorganic hybrid fillers for bone tissue engineering. For this reason, theoretical analyses were performed by the finite element method. The results from the small punch test and Young's modulus of the materials were newly correlated. The obtained values of Young's modulus (193 MPa for PCL, 378 MPa for PCL/Ti2 and 415 MPa for PCL/Zr2) were higher than those obtained from a previous theoretical modelling (144 MPa for PCL, 282 MPa for PCL/Ti2 and 310 MPa for PCL/Zr2). This correlation will be an important step for the evaluation of Young's modulus, starting from the small punch test data.

Measured Biaxial Residual Stress Maps in a Stainless Steel Weld

DOE PAGES

Olson, Mitchell D.; Hill, Michael R.; Patel, Vipul I.; ...

2015-09-16

Here, this paper describes a sequence of residual stress measurements made to determine a two-dimensional map of biaxial residual stress in a stainless steel weld. A long stainless steel (316L) plate with an eight-pass groove weld (308L filler) was used. The biaxial stress measurements follow a recently developed approach, comprising a combination of contour method and slitting measurements, with a computation to determine the effects of out-of-plane stress on a thin slice. The measured longitudinal stress is highly tensile in the weld- and heat-affected zone, with a maximum around 450 MPa, and compressive stress toward the transverse edges around ₋250more » MPa. The total transverse stress has a banded profile in the weld with highly tensile stress at the bottom of the plate (y = 0) of 400 MPa, rapidly changing to compressive stress (at y = 5 mm) of ₋200 MPa, then tensile stress at the weld root (y = 17 mm) and in the weld around 200 MPa, followed by compressive stress at the top of the weld at around ₋150 MPa. Finally, the results of the biaxial map compare well with the results of neutron diffraction measurements and output from a computational weld simulation.« less

Estimation of abbreviated mycophenolic acid area under the concentration-time curve during early posttransplant period by limited sampling strategy.

PubMed

Mohammadpour, A-H; Nazemian, F; Abtahi, B; Naghibi, M; Gholami, K; Rezaee, S; Nazari, M-R A; Rajabi, O

2008-12-01

Area under the concentration curve (AUC) of mycophenolic acid (MPA) could help to optimize therapeutic drug monitoring during the early post-renal transplant period. The aim of this study was to develop a limited sampling strategy to estimate an abbreviated MPA AUC within the first month after renal transplantation. In this study we selected 19 patients in the early posttransplant period with normal renal graft function (glomerular filtration rate > 70 mL/min). Plasma MPA concentrations were measured using reverse-phase high-performance liquid chromatography. MPA AUC(0-12h) was calculated using the linear trapezoidal rule. Multiple stepwise regression analysis was used to determine the minimal and convenient time points of MPA levels that could be used to derive model equations best fitted to MPA AUC(0-12h). The regression equation for AUC estimation that gave the best performance was AUC = 14.46 C(10) + 15.547 (r(2) = .882). The validation of the method was performed using the jackknife method. Mean prediction error of this model was not different from zero (P > .05) and had a high root mean square prediction error (8.06). In conclusion, this limited sampling strategy provided an effective approach for therapeutic drug monitoring during the early posttransplant period.

Phase Behavior of Three PBX Elastomers in High-Pressure Chlorodifluoromethane

NASA Astrophysics Data System (ADS)

Lee, Byung-Chul

2017-10-01

The phase equilibrium behavior data are presented for three kinds of commercial polymer-bonded explosive (PBX) elastomers in chlorodifluoromethane (HCFC22). Levapren^{{registered }} ethylene- co-vinyl acetate (LP-EVA), HyTemp^{{registered }} alkyl acrylate copolymer (HT-ACM), and Viton^{{registered }} fluoroelastomer (VT-FE) were used as the PBX elastomers. For each elastomer + HCFC22 system, the cloud point (CP) and/or bubble point (BP) pressures were measured while varying the temperature and elastomer composition using a phase equilibrium apparatus fitted with a variable-volume view cell. The elastomers examined in this study indicated a lower critical solution temperature phase behavior in the HCFC22 solvent. LP-EVA showed the CPs at temperatures of 323 K to 343 K and at pressures of 3 MPa to 10 MPa, whereas HT-ACM showed the CPs at conditions between 338 K and 363 K and between 4 MPa and 12 MPa. For the LP-EVA and HT-ACM elastomers, the BP behavior was observed at temperatures below about 323 K. For the VT-FE + HCFC22 system, only the CP behavior was observed at temperatures between 323 K and 353 K and at pressures between 6 MPa and 21 MPa. As the elastomer composition increased, the CP pressure increased, reached a maximum value at a specific elastomer composition, and then remained almost constant.

[Comparative study of bond strength between zirconia ceramics and 4 luting cements].

PubMed

Zheng, Hu; Zhang, Xian-Fang; Han, Dong-Wei

2007-02-01

To study the bonding strength of zirconia ceramics with 4 kinds of luting cement materials. Blocks of sintered zirconia ceramics were cut and randomly divided into 4 groups with 16 slices in each group. They were treated with sandblasting and bonded with 4 kinds of luting cements respectively. After preserved in 37 degrees C distilled-water for 24 hours and 30 days, the shear bonding strength of these specimens was tested and the data were analyzed by SAS6.12 software package and bond section were observed by scanning electron microscope. Two-way ANOVA revealed that the group of PanaviaF could attain the highest shear bonding strength: (34.7+/-3.44) MPa (after 24 hours), (31.5+/-3.44) MPa (after 1 month), which was significantly different from other treatment methods (P<0.01). The initial shear bonding strength of the groups of resin-reinforced glass ionomer was (15.5+/-2.71) MPa, (16.0+/-1.77) MPa (after 24 hours) but dropped markedly to (6.80+/-1.24) MPa, (3.38+/-2.32) MPa after 30 days (P<0.05). Resin luting cement containing phosphate monomer (MDP) can provide zirconia ceramics a strong and long-lasting bonding. Resin-reinforced glass ionomer can get good bonding strength too, but can't last long.

Physical and mechanical properties of spinach for whole-surface online imaging inspection

NASA Astrophysics Data System (ADS)

Tang, Xiuying; Mo, Chang Y.; Chan, Diane E.; Peng, Yankun; Qin, Jianwei; Yang, Chun-Chieh; Kim, Moon S.; Chao, Kuanglin

2011-06-01

The physical and mechanical properties of baby spinach were investigated, including density, Young's modulus, fracture strength, and friction coefficient. The average apparent density of baby spinach leaves was 0.5666 g/mm3. The tensile tests were performed using parallel, perpendicular, and diagonal directions with respect to the midrib of each leaf. The test results showed that the mechanical properties of spinach are anisotropic. For the parallel, diagonal, and perpendicular test directions, the average values for the Young's modulus values were found to be 2.137MPa, 1.0841 MPa, and 0.3914 MPa, respectively, and the average fracture strength values were 0.2429 MPa, 0.1396 MPa, and 0.1113 MPa, respectively. The static and kinetic friction coefficient between the baby spinach and conveyor belt were researched, whose test results showed that the average coefficients of kinetic and maximum static friction between the adaxial (front side) spinach leaf surface and conveyor belt were 1.2737 and 1.3635, respectively, and between the abaxial (back side) spinach leaf surface and conveyor belt were 1.1780 and 1.2451 respectively. These works provide the basis for future development of a whole-surface online imaging inspection system that can be used by the commercial vegetable processing industry to reduce food safety risks.

Grain-Refined AZ92 Alloy with Superior Strength and Ductility

NASA Astrophysics Data System (ADS)

Lee, Jong Un; Kim, Sang-Hoon; Jo, Wan-Kuen; Hong, Won-Hwa; Kim, Woong; Bae, Jun Ho; Park, Sung Hyuk

2018-03-01

Grain-refined AZ92 (GR-AZ92) alloy with superior tensile properties is developed by adding 1 wt% Zn and a very small amount of SiC (0.17 wt%) to commercial AZ91 alloy for enhancing the solid-solution strengthening effect and refining the crystal grains, respectively. The homogenized GR-AZ92 alloy with an average grain size of 91 μm exhibits a tensile yield strength (TYS) of 125 MPa, ultimate tensile strength (UTS) of 281 MPa, and elongation of 12.1%, which are significantly higher than those of AZ91 alloy with a grain size of 420 μm (TYS of 94 MPa, UTS of 192 MPa, and elongation of 7.0%). The peak-aging time of GR-AZ92 alloy (8 h) is significantly shorter than that of AZ91 alloy (32 h) owing to a larger amount of grain boundaries in the former, which serve as nucleation sites of Mg17Al12 precipitates. A short-aging treatment for less than 1 h of the GR-AZ92 alloy causes an effective improvement in its strength without a significant reduction in its ductility. The 30-min-aged GR-AZ92 alloy has an excellent combination of strength and ductility, with a TYS of 142 MPa, UTS of 304 MPa, and elongation of 8.0%.

The physical and mechanical properties of treated and untreated Gigantochloa Scortechinii bamboo

NASA Astrophysics Data System (ADS)

Daud, Norhasliya Mohd; Nor, Norazman Mohamad; Yusof, Mohammed Alias; Bakhri, Azrul Affandhi Mustaffa Al; Shaari, Amalina Aisyah

2018-02-01

Bamboo's advantages such as fast growing, renewable and easily available raw material meets the demand of sustainable material in construction. Bamboo act as reinforcement to enhance strength in structural members. This paper investigated on the properties of Gigantochloa Scortechinii bamboo (moisture content, density, compression, shear and bending) by referring to ISO 22157. Moisture content for both untreated and treated bamboo high at the bottom section while density is high at the top section. Compression strength for untreated bamboo were between 19.96 to 23.80 MPa and treated bamboo were between 31.74 to 36.60 MPa. High compression was at the top section which have the greatest wall thickness. Shear strength recorded between 4.28 to 5.69 MPa for untreated bamboo with node and 3.67 to 5.21 MPa for treated bamboo with node. The shear strength of samples with node recorded high strength compared to internode. Untreated bamboo recorded the MOR between 53.64 to 73.66 MPa and 58.23 to 62.86 MPa for treated bamboo. MOE of untreated bamboo were between 26.70 GPa to 36.31 GPa while treated bamboo were between 28.83 to 33.41 GPa. By replacing bamboo to the conventional building material, cost of materials will be reduced and sustainability will be enhanced.

Bacterial communities in sediment of a Mediterranean marine protected area.

PubMed

Catania, Valentina; Sarà, Gianluca; Settanni, Luca; Quatrini, Paola

2017-04-01

Biodiversity is crucial in preservation of ecosystems, and bacterial communities play an indispensable role for the functioning of marine ecosystems. The Mediterranean marine protected area (MPA) "Capo Gallo-Isola delle Femmine" was instituted to preserve marine biodiversity. The bacterial diversity associated with MPA sediment was compared with that from sediment of an adjacent harbour exposed to intense nautical traffic. The MPA sediment showed higher diversity with respect to the impacted site. A 16S rDNA clone library of the MPA sediment allowed the identification of 7 phyla: Proteobacteria (78%), Firmicutes (11%), Acidobacteria (3%), Actinobacteria (3%), Bacteroidetes (2%), Planctomycetes (2%), and Cyanobacteria (1%). Analysis of the hydrocarbon (HC)-degrading bacteria was performed using enrichment cultures. Most of the MPA sediment isolates were affiliated with Gram-positive G+C rich bacteria, whereas the majority of taxa in the harbour sediment clustered with Alpha- and Gammaproteobacteria; no Gram-positive HC degraders were isolated from the harbour sediment. Our results show that protection probably has an influence on bacterial diversity, and suggest the importance of monitoring the effects of protection at microbial level as well. This study creates a baseline of data that can be used to assess changes over time in bacterial communities associated with a Mediterranean MPA.

Impact of pressure and temperature on CO2-brine-mica contact angles and CO2-brine interfacial tension: Implications for carbon geo-sequestration.

PubMed

Arif, Muhammad; Al-Yaseri, Ahmed Z; Barifcani, Ahmed; Lebedev, Maxim; Iglauer, Stefan

2016-01-15

Precise characterization of wettability of CO2-brine-rock system and CO2-brine interfacial tension at reservoir conditions is essential as they influence capillary sealing efficiency of caprocks, which in turn, impacts the structural and residual trapping during CO2 geo-sequestration. In this context, we have experimentally measured advancing and receding contact angles for brine-CO2-mica system (surface roughness ∼12nm) at different pressures (0.1MPa, 5MPa, 7MPa, 10MPa, 15MPa, 20MPa), temperatures (308K, 323K, and 343K), and salinities (0wt%, 5wt%, 10wt%, 20wt% and 30wt% NaCl). For the same experimental matrix, CO2-brine interfacial tensions have also been measured using the pendant drop technique. The results indicate that both advancing and receding contact angles increase with pressure and salinity, but decrease with temperature. On the contrary, CO2-brine interfacial tension decrease with pressure and increase with temperature. At 20MPa and 308K, the advancing angle is measured to be ∼110°, indicating CO2-wetting. The results have been compared with various published literature data and probable factors responsible for deviations have been highlighted. Finally we demonstrate the implications of measured data by evaluating CO2 storage heights under various operating conditions. We conclude that for a given storage depth, reservoirs with lower pressures and high temperatures can store larger volumes and thus exhibit better sealing efficiency. Copyright © 2015 Elsevier Inc. All rights reserved.

Lung, liver and bone cancer mortality after plutonium exposure in beagle dogs and nuclear workers.

PubMed

Wilson, Dulaney A; Mohr, Lawrence C; Frey, G Donald; Lackland, Daniel; Hoel, David G

2010-01-01

The Mayak Production Association (MPA) worker registry has shown evidence of plutonium-induced health effects. Workers were potentially exposed to plutonium nitrate [(239)Pu(NO(3))(4)] and plutonium dioxide ((239)PuO(2)). Studies of plutonium-induced health effects in animal models can complement human studies by providing more specific data than is possible in human observational studies. Lung, liver, and bone cancer mortality rate ratios in the MPA worker cohort were compared to those seen in beagle dogs, and models of the excess relative risk of lung, liver, and bone cancer mortality from the MPA worker cohort were applied to data from life-span studies of beagle dogs. The lung cancer mortality rate ratios in beagle dogs are similar to those seen in the MPA worker cohort. At cumulative doses less than 3 Gy, the liver cancer mortality rate ratios in the MPA worker cohort are statistically similar to those in beagle dogs. Bone cancer mortality only occurred in MPA workers with doses over 10 Gy. In dogs given (239)Pu, the adjusted excess relative risk of lung cancer mortality per Gy was 1.32 (95% CI 0.56-3.22). The liver cancer mortality adjusted excess relative risk per Gy was 55.3 (95% CI 23.0-133.1). The adjusted excess relative risk of bone cancer mortality per Gy(2) was 1,482 (95% CI 566.0-5686). Models of lung cancer mortality based on MPA worker data with additional covariates adequately described the beagle dog data, while the liver and bone cancer models were less successful.

Shear bond strengths of composite to dentin using six dental adhesive systems.

PubMed

Triolo, P T; Swift, E J; Barkmeier, W W

1995-01-01

The development of adhesive agents for bonding composite to dentin has rapidly evolved in recent years. It is postulated that dentin bond strengths in the range of 17 MPa are sufficient to resist the polymerization shrinkage of composite resins. The purpose of this study was to evaluate the shear bond strengths of the following dentin adhesive systems: All-Bond 2 (Bisco), Imperva Bond (Shofu), Optibond (Kerr), Permagen (Ultradent), ProBond (Caulk/Dentsply), and Scotchbond Multi-Purpose (3M). Sixty human molars (10 per group) were mounted in phenolic rings, and the occlusal surfaces were flat ground in dentin to 600 grit. The prepared dentin bonding sites were treated according to the directions for each of the systems evaluated. A gelatin capsule technique was used to bond Bis-Fil composite cylinders to the teeth. The specimens were stored in water at 37 degrees C for 24 hours. Mean shear bond strengths were as follows: Scotchbond Multi-Purpose: 23.1 +/- 2.6 MPa, All-Bond 2: 21.4 +/- 7.8 MPa, Imperva Bond: 19.8 +/- 6.1 MPa, Optibond: 19.7 +/- 3.6 MPa, ProBond: 16.3 +/- 4.5 MPa, and Permagen: 16.2 +/- 3.0 MPa. There was not a significant difference (P<0.05) in the bond strengths of Scotchbond Multi-Purpose, All-Bond 2, Imperva Bond, and Optibond. The bond strengths of Scotchbond Multi-Purpose and All-Bond 2 were significantly greater (P<0.05) than ProBond and Permagen. Current-generation dentin adhesive systems have approached or exceeded the theoretical threshold value to resist contraction stresses during polymerization of resin materials.

[Effect of sandblasting particle sizes on bonding strength between porcelain and titanium fabricated by rapid laser forming].

PubMed

Zhang, Li-jun; Wang, Zhong-yi; Gao, Bo; Gao, Yang; Zhang, Chun-bao

2009-11-01

To evaluate the effect of sandblasting particle sizes of Al2O3 on the bonding strength between porcelain and titanium fabricated by laser rapid forming (LRF). The thermal expansion coefficient, roughness (Ra), contact angle, surface morphology of titanium surface and the bonding strength between titanium and porcelain were evaluated after the titanium surface being sandblasted using different sizes of Al2O3 (50 microm, 120 microm, 250 microm) at a pressure of 0.5 MPa. The cast titanium specimens were used as control, and were sandblasted with 50 microm Al2O3 at the same pressure. The thermal expansion coefficient of cast titanium [(9.84 +/- 0.42) x 10(-6)/ degrees C] and LRF Ti [(9.79 +/- 0.31) x 10(-6)/ degrees C) matched that of Noritake Ti-22 dentin porcelain [(8.93 +/- 0.36) x 10(-6)/ degrees C). When larger size of Al2O3 was used, the value of Ra and contact angle increased as well. There was no significant difference in bonding strength between the LRF Ti-50 microm [(25.91 +/- 1.02) MPa] and cast titanium [(26.42 +/- 1.65) MPa]. Significantly lower bonding strength was found in LRF Ti-120 microm [(21.86 +/- 1.64) MPa] and LRF Ti-250 microm [(19.96 +/- 1.03) MPa]. The bond strength between LRF Ti and Noritake Ti-22 dentin porcelain was above the lower limit value in the ISO 9693 (25 MPa) after using 50 microm Al2O3 sandblasting in 0.5MPa air pressure.

Laser quench hardening of steel: Effects of superimposed elastic pre-stress on the hardness and residual stress distribution

NASA Astrophysics Data System (ADS)

Meserve, Justin

Cold drawn AISI 4140 beams were LASER surface hardened with a 2 kW CO2 LASER. Specimens were treated in the free state and while restrained in a bending fixture inducing surface tensile stresses of 94 and 230 MPa. Knoop hardness indentation was used to evaluate the through thickness hardness distribution, and a layer removal methodology was used to evaluate the residual stress distribution. Results showed the maximum surface hardness attained was not affected by pre-stress during hardening, and ranged from 513 to 676 kg/mm2. The depth of effective hardening varied at different magnitudes of pre-stress, but did not vary proportionately to the pre-stress. The surface residual stress, coinciding with the maximum compressive residual stress, increased as pre-stress was increased, from 1040 MPa for the nominally treated specimens to 1270 MPa for specimens pre-stressed to 230 MPa. The maximum tensile residual stress observed in the specimens decreased from 1060 MPa in the nominally treated specimens to 760 MPa for specimens pre-stressed to 230 MPa. Similarly, thickness of the compressive residual stress region increased and the depth at which maximum tensile residual stress occurred increased as the pre-stress during treatment was increased Overall, application of tensile elastic pre-stress during LASER hardening is beneficial to the development of compressive residual stress in AISI 4140, with minimal impact to the hardness attained from the treatment. The newly developed approach for LASER hardening may support efforts to increase both the wear and fatigue resistance of parts made from hardenable steels.

Bond strengths of different orthodontic adhesives after enamel conditioning with the same self-etching primer.

PubMed

Scougall-Vilchis, Rogelio J; Zárate-Díaz, Chrisel; Kusakabe, Shusuke; Yamamoto, Kohji

2010-05-01

To determine the shear bond strengths (SBS) of stainless steel brackets bonded with seven light-cured orthodontic adhesives after the enamel was conditioned with the same self-etching primer. A total of 140 extracted human molars were randomly divided into seven groups (N = 20). In all the groups, the enamel was conditioned with Transbond Plus SEP (TPSEP). Stainless steel brackets were bonded with the following orthodontic adhesives: Group I, Transbond XT; Group II, Blūgloo; Group III, BeautyOrtho Bond; Group IV, Enlight; Group V, Light Bond; Group VI, Transbond CC; Group VII, Xeno Ortho. The teeth were stored in distilled water at 37 degrees C for 24 hours and debonded with a universal testing machine. The modified adhesive remnant index (ARI) was also recorded. There were no significant differences in the SBS values among the groups: I (18.0 +/- 7.4 MPa); II (18.3 +/- 5.1 MPa); III (14.8 +/- 4.3 MPa); IV (18.3 +/- 7.0 MPa); V (16.4 +/- 4.3 MPa); VI (20.3 +/- 5.3 MPa); VII (15.9 +/- 6.4 MPa), but significant differences in ARI were found. The seven orthodontic adhesives evaluated in this study can be successfully used for bonding stainless steel brackets when the enamel is conditioned with TPSEP, however, the differences among some groups might influence the clinical bond strengths. In addition, the amount of residual adhesive remaining on the teeth after debonding differed among the adhesives. Further studies are required to better understand the differences in SBS and ARI.

Effects of high hydrostatic pressure or hydrophobic modification on thermal stability of xanthine oxidase.

PubMed

Halalipour, Ali; Duff, Michael R; Howell, Elizabeth E; Reyes-De-Corcuera, José I

2017-08-01

The effect of high hydrostatic pressure (HHP) on the kinetics of thermal inactivation of xanthine oxidase (XOx) from bovine milk was studied. Inactivation of XOx followed pseudo-first-order kinetics at 0.1-300MPa and 55.0-70.0°C. High pressure up to at least 300MPa stabilized XOx at all the studied temperatures. The highest stabilization effect of HHP on XOx was at 200-300MPa at 55.0 and 58.6°C, and at 250-300MPa at 62.3-70.0°C. The stability of XOx increased 9.5 times at 300MPa and 70.0°C compared to atmospheric pressure at the same temperature. The activation energy of inactivation of XOx decreased with pressure and was 1.9 times less at 300MPa (97.0±8.2kJmol -1 ) than at 0.1MPa (181.7±12.1kJmol -1 ). High pressure decreased the dependence of the rate constant of inactivation to temperature effects compared to atmospheric pressure. The stabilizing effect of HHP on XOx was highest at 70.0°C where the activation volume of inactivation of XOx was 28.9±2.9cm 3 mol -1 . A second approach to try to increase XOx stability involved hydrophobic modification using aniline or benzoate. However, the thermal stability of XOx remained unaffected after 8-14 modifications of carboxyl side groups per XOx monomer with aniline, or 12-17 modifications of amino side groups per XOx monomer with benzoate. Copyright © 2017 Elsevier Inc. All rights reserved.

Impact of high pressure treatment on functional, rheological, pasting, and structural properties of lentil starch dispersions.

PubMed

Ahmed, Jasim; Thomas, Linu; Taher, Ayoub; Joseph, Antony

2016-11-05

Lentil starch (LS) dispersions (flour to water 1:4w/w) were subjected to high pressure (HP) treatment at 0.1, 400, 500 and 600MPa for 10min, followed by evaluation on the functional, particle size, rheological, pasting, and structural properties of post-process samples. Water holding capacity of pressurized starch increased with the pressure intensity due to increase in damaged starch. The amount of resistant starch increased from 5 to 6.8% after pressure treatment at 600MPa. An increase in starch granule particle size (196-207μm) was obvious after HP treatment. The lentil starch was completely gelatinized after pressure treatment at 600MPa for 10min as evidenced from differential scanning calorimetry, rheometry, X-ray diffraction (XRD) and scanning electron microscopy observation. The elastic modulus, G' of lentil starch gel was less frequency dependent, and higher in magnitude at high pressure (>500MPa) than at lower pressure range (≤400MPa). XRD analysis revealed the disappearance of two diffraction peak intensities at 14.86° and 22.82° at 600MPa for 10min, which confirms the transformation of crystalline to amorphous region of lentil starch. Pasting properties were significantly influenced by the pressure treatment especially at 600MPa, resulting in a considerable decrease in peak viscosity, breakdown and final viscosity, and an increase in peak time. It can be inferred that the functional properties of pressure-treated LS are mainly based on the structural destruction of granules. Copyright © 2016 Elsevier Ltd. All rights reserved.

In vitro tensile bond strength of adhesive cements to new post materials.

PubMed

O'Keefe, K L; Miller, B H; Powers, J M

2000-01-01

The purpose of this study was to measure the in vitro tensile bond strength of 3 types of adhesive resin cements to stainless steel, titanium, carbon fiber-reinforced resin, and zirconium oxide post materials. Disks of post materials were polished to 600 grit, air abraded, and ultrasonically cleaned. Zirconium oxide bonding surfaces were pretreated with hydrofluoric acid and silanated. Bis-Core, C&B Metabond, and Panavia cements were bonded to the post specimens and placed in a humidor for 24 hours. Post specimens were debonded in tension. Means and standard deviations (n = 5) were analyzed by 2-way analysis of variance. Tukey-Kramer intervals at the 0.05 significance level were calculated. Failure modes were observed. Panavia 21 provided the highest bond strengths for all types of post materials, ranging from 22 MPa (zirconium oxide) to 37 MPa (titanium). C&B Metabond bonded significantly more strongly to stainless steel (27 MPa) and titanium (22 MPa) than to zirconium oxide (7 MPa). Bis-Core results were the lowest, ranging from 16 MPa (stainless steel) to 8 MPa (zirconium oxide). In most cases, bonds to carbon fiber post materials were weaker than to stainless steel and titanium, but stronger than to zirconium oxide. In general, higher bond strengths resulted in a higher percentage of cohesive failures within the cement. Panavia 21 provided the highest bond strengths to all post materials, followed by C&B Metabond. In most cases, adhesive resins had higher bond strengths to stainless steel, titanium, and carbon fiber than to zirconium oxide.

Elastic-Plastic Thermal Stress Analysis of a High-Pressure Cryogenic Storage Tank

NASA Technical Reports Server (NTRS)

Barker, J. Mark; Field, Robert E. (Technical Monitor)

2003-01-01

The thermal stresses on a cryogenic storage tank contribute strongly to the state of stress of the tank material and its ability to withstand operational stresses. These thermal stresses also affect the growth of any surface damage that might occur in the tank walls. These stresses are particularly of concern during the initial cooldown period for a new tank placed into service, and during any subsequent thermal cycles. A previous preliminary elastic analysis showed that the thermal stress on the inner wall would reach approximately 1,000MPa (145,000 psi). This stress far exceeds the ASTM specified room temperature values for both yield (170MPa) and ultimate (485 MPa) strength for 304L stainless steel. The present analysis determines the thermal stresses using an elastic-plastic model. The commercial software application ANSYS was used to determine the transient spatial temperature profile and the associated spatial thermal stress profiles in a segment of a thick-walled vessel during a typical cooldown process. A strictly elastic analysis using standard material properties for 304L stainless steel showed that the maximum thermal stress on the inner and outer walls was approximately 960 MPa (tensile) and - 270 MPa (compressive) respectively. These values occurred early in the cooldown process, but at different times, An elastic-plastic analysis showed significantly reducing stress, as expected due to the plastic deformation of the material. The maximum stress for the inner wall was approximately 225 MPa (tensile), while the maximum stress for the outer wall was approximately - 130 MPa (compressive).

[The Study of Decitabine Effect on the Endometrial Carcinoma Xenografted in Nude Mice.

PubMed

Li, Ran-Hong; Wang, Xue-Ping; Liu, Hui

2016-11-01

To explore the effect of the demethylation drug 5-Aza-CdR on endometrial carcinoma xenografted in nude mice. Randomly assigned the mice into decitabine (AZA),cisplatin (DDP),medroxyprogesterone acetate (MPA),AZA+DDP,AZA+MPA,DDP+MPA and model groups (three in each group) after building the models of xenografted tumor by transplanting the HEC-1B cells on nude mice,and dealt them respectively with corresponding drugs (1 μg/g,single or combination) in the experiment groups and normal saline in model group (injected per 3 d,8 injections in total).Then the tumor inhibitory rates in different groups were calculated.The methylation and protein expression of RASSF1A gene was estimated by methylation specific PCR (MSP) and Western blot respectively,and apoptosis situation of carcinoma cell was estimated by tunel. Inhibitory rate in AZA+DDP group was the highest,and the lowest was AZA group. RASSF1A gene promoter region methylation levels of AZA,AZA+DDP and AZA+MPA groups significantly reduced and showed obvious demethylation stripes while other groups mainly showed the methylation stripes.The differences of RASSF1A protein expression between AZA,AZA+DDP and AZA+MPA groups were not statistical significant ( P >0.05),but the three were higher than model group ( P <0.05);there was no statistically significant difference respectively in the DDP,MPA,DDP+ MPA groups compared with that of model group ( P >0.05).In the comparison of apoptosis index,model group was the lowest,followed by the three single medicine groups,and the highest was three combination groups ( P <0.05). Demethylation drug 5-Aza-CdR in endometrial cancer treatment has a great potential clinical application value by reversing the abnormal methylation of RASSF1A gene,restoring biological functions of RASSF1A protein and strengthening the efficacy of DDP and MPA.

Prolonged performance-related neuroendocrine activation and perseverative cognition in low- and high-anxious university music students.

PubMed

Gomez, Patrick; Nielsen, Carole; Studer, Regina K; Hildebrandt, Horst; Klumb, Petra L; Nater, Urs M; Wild, Pascal; Danuser, Brigitta

2018-05-14

Music performances are social-evaluative situations that can elicit marked short-term neuroendocrine activation and anxious thoughts especially in musicians suffering from music performance anxiety (MPA). The temporal patterns of neuroendocrine activity and concert-related worry and rumination (perseverative cognition, PC) days before and after a concert in low- and high-anxious musicians are unknown. The first goal of the present study was to investigate the prolonged effects of a solo music performance and the effects of trait MPA on salivary cortisol (sC), alpha-amylase (sAA), and concert-related PC. The second goal was to investigate whether concert-related PC is associated with neuroendocrine activity and mediates the effects of measurement day and trait MPA on neuroendocrine responses. Seventy-two university music students collected saliva samples and reported their PC for seven consecutive days. On the fifth day, they performed solo. Measurement day and trait MPA were tested as main predictors of the diurnal area under the curve with respect to ground (sC AUCg, sAA AUCg), awakening responses, and PC. SC AUCg, sAA AUCg, and concert-related PC were highest on concert day. SC AUCg decreased only partially on post-concert days. SAA AUCg remained elevated on the first post-concert day among students with moderate to very high trait MPA. Throughout the assessment period, trait MPA was associated with smaller sC AUCg and higher concert-related PC. Concert-related PC showed significant positive associations with sC AUCg and sAA AUCg but did not mediate the effects of measurement day and trait MPA on these measures. These findings suggest that solo music performances have prolonged neuroendocrine effects and that trait MPA is an important factor having specific effects on university music students' hypothalamic-pituitary-adrenal axis, autonomic nervous system, and cognitive activity. Copyright © 2018 Elsevier Ltd. All rights reserved.

Survivorship of standard versus modified posterior surgical approaches in metal-on-metal hip resurfacing.

PubMed

M Takamura, K; Maher, P; Nath, T; Su, E P

2014-05-01

Metal-on-metal hip resurfacing (MOMHR) is available as an alternative option for younger, more active patients. There are failure modes that are unique to MOMHR, which include loosening of the femoral head and fractures of the femoral neck. Previous studies have speculated that changes in the vascularity of the femoral head may contribute to these failure modes. This study compares the survivorship between the standard posterior approach (SPA) and modified posterior approach (MPA) in MOMHR. A retrospective clinical outcomes study was performed examining 351 hips (279 male, 72 female) replaced with Birmingham Hip Resurfacing (BHR, Smith and Nephew, Memphis, Tennessee) in 313 patients with a pre-operative diagnosis of osteoarthritis. The mean follow-up period for the SPA group was 2.8 years (0.1 to 6.1) and for the MPA, 2.2 years (0.03 to 5.2); this difference in follow-up period was statistically significant (p < 0.01). Survival analysis was completed using the Kaplan-Meier method. At four years, the Kaplan-Meier survival curve for the SPA was 97.2% and 99.4% for the MPA; this was statistically significant (log-rank; p = 0.036). There were eight failures in the SPA and two in the MPA. There was a 3.5% incidence of femoral head collapse or loosening in the SPA and 0.4% in the MPA, which represented a significant difference (p = 0.041). There was a 1.7% incidence of fractures of the femoral neck in the SPA and none in the MPA (p = 0.108). This study found a significant difference in survivorship at four years between the SPA and the MPA (p = 0.036). The clinical outcomes of this study suggest that preserving the vascularity of the femoral neck by using the MPA results in fewer vascular-related failures in MOMHRs. Cite this article: Bone Joint Res 2014;3:150-4. ©2014 The British Editorial Society of Bone & Joint Surgery.

Survivorship of standard versus modified posterior surgical approaches in metal-on-metal hip resurfacing

PubMed Central

M. Takamura, K.; Maher, P.; Nath, T.; Su, E. P.

2014-01-01

Objectives Metal-on-metal hip resurfacing (MOMHR) is available as an alternative option for younger, more active patients. There are failure modes that are unique to MOMHR, which include loosening of the femoral head and fractures of the femoral neck. Previous studies have speculated that changes in the vascularity of the femoral head may contribute to these failure modes. This study compares the survivorship between the standard posterior approach (SPA) and modified posterior approach (MPA) in MOMHR. Methods A retrospective clinical outcomes study was performed examining 351 hips (279 male, 72 female) replaced with Birmingham Hip Resurfacing (BHR, Smith and Nephew, Memphis, Tennessee) in 313 patients with a pre-operative diagnosis of osteoarthritis. The mean follow-up period for the SPA group was 2.8 years (0.1 to 6.1) and for the MPA, 2.2 years (0.03 to 5.2); this difference in follow-up period was statistically significant (p < 0.01). Survival analysis was completed using the Kaplan–Meier method. Results At four years, the Kaplan–Meier survival curve for the SPA was 97.2% and 99.4% for the MPA; this was statistically significant (log-rank; p = 0.036). There were eight failures in the SPA and two in the MPA. There was a 3.5% incidence of femoral head collapse or loosening in the SPA and 0.4% in the MPA, which represented a significant difference (p = 0.041). There was a 1.7% incidence of fractures of the femoral neck in the SPA and none in the MPA (p = 0.108). Conclusion This study found a significant difference in survivorship at four years between the SPA and the MPA (p = 0.036). The clinical outcomes of this study suggest that preserving the vascularity of the femoral neck by using the MPA results in fewer vascular-related failures in MOMHRs. Cite this article: Bone Joint Res 2014;3:150–4 PMID:24842931

Tensile and bending fatigue of the adhesive interface to dentin.

PubMed

Belli, Renan; Baratieri, Luiz Narciso; Braem, Marc; Petschelt, Anselm; Lohbauer, Ulrich

2010-12-01

The aim of this study was to evaluate the fatigue limits of the dentin-composite interfaces established either with an etch-and-rinse or an one-step self-etch adhesive systems under tensile and bending configurations. Flat specimens (1.2 mm×5 mm×35 mm) were prepared using a plexiglass mold where dentin sections from human third molars were bonded to a resin composite, exhibiting the interface centrally located. Syntac Classic and G-Bond were used as adhesives and applied according to the manufacturer's instructions. The fluorochrome Rhodamine B was added to the adhesives to allow for fractographic evaluation. Tensile strength was measured in an universal testing machine and the bending strength (n=15) in a Flex machine (Flex, University of Antwerp, Belgium), respectively. Tensile (TFL) and bending fatigue limits (BFL) (n=25) were determined under wet conditions for 10(4) cycles following a staircase approach. Interface morphology and fracture mechanisms were observed using light, confocal laser scanning and scanning electron microscopy. Statistical analysis was performed using three-way ANOVA (mod LSD test, p<0.05). Tensile and bending characteristic strengths at 63.2% failure probability for Syntac were 23.8 MPa and 71.5 MPa, and 24.7 MPa and 72.3 MPa for G-Bond, respectively. Regarding the applied methods, no significant differences were detected between adhesives. However, fatigue limits for G-Bond (TFL=5.9 MPa; BFL=36.2 MPa) were significantly reduced when compared to Syntac (TFL=12.6 MPa; BFL=49.7 MPa). Fracture modes of Syntac were generally of adhesive nature, between the adhesive resin and dentin, while G-Bond showed fracture planes involving the adhesive-dentin interface and the adhesive resin. Cyclic loading under tensile and bending configurations led to a significant strength degradation, with a more pronounced fatigue limit decrease for G-Bond. The greater decrease in fracture strength was observed in the tensile configuration. Copyright © 2010 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Effect of high-pressure treatment at various temperatures on indigenous proteolytic enzymes and whey protein denaturation in bovine milk.

PubMed

Moatsou, Golfo; Bakopanos, Constantinos; Katharios, Dimitis; Katsaros, George; Kandarakis, Ioannis; Taoukis, Petros; Politis, Ioannis

2008-08-01

The objective of the present study was to determine the effect of high pressure (HP) processing (200, 450 and 650 MPa) at various temperatures (20, 40 and 55 degrees C) on the total plasmin plus plasminogen-derived activity (PL), plasminogen activator(s) (PA) and cathepsin D activities and on denaturation of major whey proteins in bovine milk. Data indicated that transfer of both PL and PA from the casein micelles to milk serum occurred at all pressures utilized at room temperature (20 degrees C). In addition to the transfer of PL and PA from micelles, there were reductions in activities of PL (16-18%) and PA (38-62%) for the pressures 450 and 650 MPa, at room temperature. There were synergistic negative effects between pressure and temperature on residual PL activity at 450 and 650 MPa and on residual PA activity only at 450 MPa. Cathepsin D activity in the acid whey from HP-treated milk was in general baroresistant at room temperature. The residual activity of cathepsin D decreased significantly at 650 MPa and 40 degrees C and at the pressures 450 and 650 MPa at 55 degrees C. Synergistic negative effects on the amount of native beta-lactoglobulin were observed at 450 and 650 MPa and on the amount of native alpha-lactalbumin at 650 MPa. There were significant correlations between enzymatic activities (PL, PA and cathepsin D) and the residual native beta-lactoglobulin and alpha-lactalbumin in bovine milk. In conclusion, HP significantly affected the activity of indigenous proteolytic enzymes and whey protein denaturation in bovine milk. Reduction in activity of indigenous enzymes (PL, PA and cathepsin D) and transfer of PL and PA from the casein to milk serum induced by HP is expected to have a profound effect on cheese yield, proteolysis during cheese ripening and quality of UHT milk during storage.

Exposure–effect relationship of mycophenolic acid and prednisolone in adult patients with lupus nephritis

PubMed Central

Abd Rahman, Azrin N; Tett, Susan E; Abdul Gafor, Halim A; McWhinney, Brett C; Staatz, Christine E

2015-01-01

Aims The aim was to examine relationships between total and unbound mycophenolic acid (MPA) and prednisolone exposure and clinical outcomes in patients with lupus nephritis. Methods Six blood samples were drawn pre- and at 1, 2, 4, 6 and 8 h post-dose and total and unbound MPA and prednisolone pre-dose (C0), maximum concentration (Cmax) and area under the concentration–time curve (AUC) were determined using non-compartmental analysis in 25 patients. The analyses evaluated drug exposures in relation to treatment response since starting MPA and drug-related adverse events. Results Dose-normalized AUC varied 10-, 8-, 7- and 19-fold for total MPA, unbound MPA, total prednisolone and unbound prednisolone, respectively. Median values (95% CI) of total MPA AUC(0,8 h) (21.5 [15.0, 42.0] vs. 11.2 [4.8, 30.0] mg l–1 h, P= 0.048) and Cmax (11.9 [6.7, 26.3] vs. 6.1 [1.6, 9.2] mg l–1, P = 0.016) were significantly higher in responders than non-responders. Anaemia was significantly associated with higher total (37.8 [14.1, 77.5] vs. 18.5 [11.7, 32.7] mg l–1 h, P = 0.038) and unbound MPA AUC(0,12 h) (751 [214, 830] vs. 227 [151, 389] mg l–1 h, P = 0.004). Unbound prednisolone AUC(0,24 h) was significantly higher in patients with Cushingoid appearance (unbound: 1372 [1242, 1774] vs. 846 [528, 1049] nmol l–1 h, P = 0.019) than in those without. Poorer treatment response was observed in patients with lowest tertile exposure to both total MPA and prednisolone as compared with patients with middle and higher tertile exposure (17% vs. 74%, P = 0.023). Conclusions This study suggests a potential role for therapeutic drug monitoring in individualizing immunosuppressant therapy in patients with lupus nephritis. PMID:25959850

Exposure-effect relationship of mycophenolic acid and prednisolone in adult patients with lupus nephritis.

PubMed

Abd Rahman, Azrin N; Tett, Susan E; Abdul Gafor, Halim A; McWhinney, Brett C; Staatz, Christine E

2015-11-01

The aim was to examine relationships between total and unbound mycophenolic acid (MPA) and prednisolone exposure and clinical outcomes in patients with lupus nephritis. Six blood samples were drawn pre- and at 1, 2, 4, 6 and 8 h post-dose and total and unbound MPA and prednisolone pre-dose (C0 ), maximum concentration (Cmax ) and area under the concentration-time curve (AUC) were determined using non-compartmental analysis in 25 patients. The analyses evaluated drug exposures in relation to treatment response since starting MPA and drug-related adverse events. Dose-normalized AUC varied 10-, 8-, 7- and 19-fold for total MPA, unbound MPA, total prednisolone and unbound prednisolone, respectively. Median values (95% CI) of total MPA AUC(0,8 h) (21.5 [15.0, 42.0] vs. 11.2 [4.8, 30.0] mg l(-1) h, P= 0.048) and Cmax (11.9 [6.7, 26.3] vs. 6.1 [1.6, 9.2] mg l(-1) , P = 0.016) were significantly higher in responders than non-responders. Anaemia was significantly associated with higher total (37.8 [14.1, 77.5] vs. 18.5 [11.7, 32.7] mg l(-1) h, P = 0.038) and unbound MPA AUC(0,12 h) (751 [214, 830] vs. 227 [151, 389] mg l(-1) h, P = 0.004). Unbound prednisolone AUC(0,24 h) was significantly higher in patients with Cushingoid appearance (unbound: 1372 [1242, 1774] vs. 846 [528, 1049] nmol l(-1) h, P = 0.019) than in those without. Poorer treatment response was observed in patients with lowest tertile exposure to both total MPA and prednisolone as compared with patients with middle and higher tertile exposure (17% vs. 74%, P = 0.023). This study suggests a potential role for therapeutic drug monitoring in individualizing immunosuppressant therapy in patients with lupus nephritis. © 2015 The British Pharmacological Society.

Serum progesterone in pregnant bitches supplemented with progestin because of expected or suspected luteal insufficiency.

PubMed

Günzel-Apel, A; Urhausen, C; Wolf, K; Einspanier, A; Oei, C; Piechotta, M

2012-12-01

Progesterone profiles of individual bitches may vary considerably both between and within individuals during pregnancy and non-pregnancy. Suspected luteal deficiency is commonly purported but is difficult to evaluate in clinical cases when progesterone is supplemented because this masks the underlying hormone changes. Therefore, in this study, suspected cases of luteal deficiency (six pregnancies from five bitches) were supplemented with oral medroxyprogesterone acetate (MPA), allowing measurement of endogenous progesterone using conventional assay. MPA (0.1 mg/kg) treatment commenced between days 30 and 36 after estimated ovulation and was continued for 18-28 days. Endogenous progesterone was measured throughout treatment, and blood was additionally analysed for prolactin (PRL) and relaxin (RLN) as well as MPA. The latter revealed delayed MPA clearance in two bitches, in which Caesarean operation had to be performed because of a low foetal heart rate. In two cases with confirmed basal concentrations of both P(4) and MPA at term, spontaneous parturition occurred. Low endogenous progesterone during pregnancy was not apparent in three bitches that had previously had a short inter-oestrous interval of which two had previously had confirmed short luteal phase. However, in the remaining two cases, there had been previous pregnancy failure, but in only one of these, a premature decrease in endogenous progesterone to <2 ng/ml was detected. The latter had also low concentrations of PRL and RLN. The results of this preliminary clinical study suggest that abnormal progesterone profiles in pregnancy may be uncommon in bitches even when there has been previously documented short inter-oestrous interval. However, luteal deficiency may be suspected in bitches with a history of repeated pregnancy failure or abortion. MPA supplementation appears to be efficacious for management of suspected luteal deficiency and verification of the ovarian dysfunction, but care should be taken regarding the timing of MPA withdrawal and prolongation of pregnancy because of delayed elimination of MPA from blood circulation. © 2012 Blackwell Verlag GmbH.

Inactivation of Vibrio parahaemolyticus in hard clams (Mercanaria mercanaria) by high hydrostatic pressure (HHP) and the effect of HHP on the physical characteristics of hard clam meat.

PubMed

Mootian, Gabriel K; Flimlin, George E; Karwe, Mukund V; Schaffner, Donald W

2013-02-01

Shellfish may internalize dangerous pathogens during filter feeding. Traditional methods of depuration have been found ineffective against certain pathogens. The objective was to explore high hydrostatic pressure (HHP) as an alternative to the traditional depuration process. The effect of HHP on the survival of Vibrio parahaemolyticus in live clams (Mercanaria mercanaria) and the impact of HHP on physical characteristics of clam meat were investigated. Clams were inoculated with up to 7 log CFU/g of a cocktail of V. parahaemolyticus strains via filter feeding. Clams were processed at pressures ranging from 250 to 552 MPa for hold times ranging between 2 and 6 min. Processing conditions of 450 MPa for 4 min and 350 MPa for 6 min reduced the initial concentration of V. parahaemolyticus to a nondetectable level (<10(1) CFU/g), achieving >5 log reductions. The volume of clam meat (processed in shell) increased with negligible change in mass after exposure to pressure at 552 MPa for 3 min, while the drip loss was reduced. Clams processed at 552 MPa were softer compared to those processed at 276 MPa. However, all HHP processed clams were found to be harder compared to unprocessed. The lightness (L*) of the meat increased although the redness (a*) decreased with increasing pressure. Although high pressure-processed clams may pose a significantly lower risk from V. parahaemolyticus, the effect of the accompanied physical changes on the consumer's decision to purchase HHP clams remains to be determined. Shellfish may contain dangerous foodborne pathogens. Traditional methods of removing those pathogen have been found ineffective against certain pathogens. The objective of this research was to determine the effect of high hydrostatic pressure on V. parahaemolyticus in clams. Processing conditions of 450 MPa for 4 min and 350 MPa for 6 min reduced the initial concentration of V. parahaemolyticus to a nondetectable level, achieving >5 log reductions. © 2013 Institute of Food Technologists®

Maximum a posteriori Bayesian estimation of mycophenolic Acid area under the concentration-time curve: is this clinically useful for dosage prediction yet?

PubMed

Staatz, Christine E; Tett, Susan E

2011-12-01

This review seeks to summarize the available data about Bayesian estimation of area under the plasma concentration-time curve (AUC) and dosage prediction for mycophenolic acid (MPA) and evaluate whether sufficient evidence is available for routine use of Bayesian dosage prediction in clinical practice. A literature search identified 14 studies that assessed the predictive performance of maximum a posteriori Bayesian estimation of MPA AUC and one report that retrospectively evaluated how closely dosage recommendations based on Bayesian forecasting achieved targeted MPA exposure. Studies to date have mostly been undertaken in renal transplant recipients, with limited investigation in patients treated with MPA for autoimmune disease or haematopoietic stem cell transplantation. All of these studies have involved use of the mycophenolate mofetil (MMF) formulation of MPA, rather than the enteric-coated mycophenolate sodium (EC-MPS) formulation. Bias associated with estimation of MPA AUC using Bayesian forecasting was generally less than 10%. However some difficulties with imprecision was evident, with values ranging from 4% to 34% (based on estimation involving two or more concentration measurements). Evaluation of whether MPA dosing decisions based on Bayesian forecasting (by the free website service https://pharmaco.chu-limoges.fr) achieved target drug exposure has only been undertaken once. When MMF dosage recommendations were applied by clinicians, a higher proportion (72-80%) of subsequent estimated MPA AUC values were within the 30-60 mg · h/L target range, compared with when dosage recommendations were not followed (only 39-57% within target range). Such findings provide evidence that Bayesian dosage prediction is clinically useful for achieving target MPA AUC. This study, however, was retrospective and focussed only on adult renal transplant recipients. Furthermore, in this study, Bayesian-generated AUC estimations and dosage predictions were not compared with a later full measured AUC but rather with a further AUC estimate based on a second Bayesian analysis. This study also provided some evidence that a useful monitoring schedule for MPA AUC following adult renal transplant would be every 2 weeks during the first month post-transplant, every 1-3 months between months 1 and 12, and each year thereafter. It will be interesting to see further validations in different patient groups using the free website service. In summary, the predictive performance of Bayesian estimation of MPA, comparing estimated with measured AUC values, has been reported in several studies. However, the next step of predicting dosages based on these Bayesian-estimated AUCs, and prospectively determining how closely these predicted dosages give drug exposure matching targeted AUCs, remains largely unaddressed. Further prospective studies are required, particularly in non-renal transplant patients and with the EC-MPS formulation. Other important questions remain to be answered, such as: do Bayesian forecasting methods devised to date use the best population pharmacokinetic models or most accurate algorithms; are the methods simple to use for routine clinical practice; do the algorithms actually improve dosage estimations beyond empirical recommendations in all groups that receive MPA therapy; and, importantly, do the dosage predictions, when followed, improve patient health outcomes?

Fatigue 󈨛. Volume 1,

DTIC Science & Technology

1987-06-01

1983,1256. (6) McMahon, C. J., Editor, " Microplasticity ", Wiley Interscience, New York, New York, 1968. (7) Talia, J. E., Fernandez, L., and Gibala, R...during fatigue. The alloy has a 360 MPa bulk cyclic yield strength, but its surface is microplastic at cyclic stresses greater than 70 MPa. With...sensitivity measurements of Wo made early in fatigue show the surface is microplastic at stresses greater than 70 MPa (Fig. 2). In fact, the stress

Product Design and Production Practice of 700MPa High Strength Hot Rolled Strip for Auto Axle Tube

NASA Astrophysics Data System (ADS)

Hui, Pan; Zhao-dong, Wang; Ya-jun, Hui; Yang, Cui; Xiang-tao, Deng; Chun-lin, Bao

According to the technical specifications of 700MPa high strength automotive axle tube steel, a low cost of 0.07%C+1.5%Mn+0.05%Nb+0.10%Ti was designed. The high strength mainly relies on grain refinement strengthening and precipitation strengthening. The recrystallization, precipitation, and CCT curves of the 700MPa grade axle tube steel were studied in order to determine a reasonable TMCP process. By controlling the low level segregation band, low level of C and N content, 700MPa grade high strength automotive axle tube steel is successfully developed with excellent mechanical property, welding property, flattening and flaring property, torsion fatigue property, static torsional property and surface quality.

Environmental Durability Testing of Structural Adhesives. Part I. AF- 143-2/EC-3917; PL-729-3/PL-728

DTIC Science & Technology

1978-12-01

Mode (6 ( 4C ) No Load (psi) (MPa) (I Coh.Failura) 72 22 None 3040 20.9 100 72 22 None 3000 20.7 100 72 22 None 3020 20.8 100 72 22 None 2960 20.4 1.00 72... 4C ) No LOa4 Ji (psi) (MPa) (9 Coh.Failurs) 72 22 None 5560 38.3 100 72 22 None 5700 39.3 100 72 22 None 5660 39.0 50 72 22 None 5590 38.5 80 72 22...F dry Failure Shear Strength Mode (psi) (MPa) ultimatoe ( hrm ) (psi) (MPa) (% Coh.) 2420 16.7 80 0.30 100 2420 16.7 g0 0.50 100 2420 16.7 80 1.25 100

Solubility of the sesquiterpene alcohol patchoulol in supercritical carbon dioxide

PubMed Central

Hybertson, Brooks M.

2009-01-01

The solubility of the sesquiterpene alcohol patchoulol in supercritical carbon dioxide was measured at P ranging from 10.0 MPa to 25.0 MPa and T of 40.0 and 50.0 °C using a simple microsampling type apparatus with a 100.5 µL sample loop to remove aliquots for off-line analysis. The system was first validated using vanillin with off-line spectrophotometric analysis, then utilized for patchoulol measurements with off-line GC-MS analysis. The measured solubility of patchoulol in supercritical CO2 ranged from mole fractions of 0.43 × 10−3 at 10.0 MPa and 50.0 °C to 9.45 × 10−3 at 25.0 MPa and 40.0 °C. PMID:19424449

Tensile Properties of Under-Matched Weld Joints for 950 MPa Steel.

NASA Astrophysics Data System (ADS)

Yamamoto, Kouji; Arakawa, Toshiaki; Akazawa, Nobuki; Yamamoto, Kousei; Matsuo, Hiroki; Nakagara, Kiyoyuki; Suita, Yoshikazu

In welding of 950 MPa-class high tensile strength steel, preheating is crucial in order to avoid cold cracks, which, however, eventually increases welding deformations. One way to decrease welding deformations is lowering preheating temperature by using under-matched weld metal. Toyota and others clarify that although breaking elongation can decrease due to plastic constraint effect under certain conditions, static tensile of under-matched weld joints is comparable to that of base metal. However, there has still been no report about joint static tensile of under-matched weld joints applied to 950 MPa-class high tensile strength steel. In this study, we aim to research tensile strength and fatigue strength of under-matched weld joints applied to 950 MPa-class high tensile steel.

Stress and Pore Pressure Measurement in IODP Riser Drilling: An Example from Expedition 319, Kumano Basin offshore SW Honshu, Japan

NASA Astrophysics Data System (ADS)

Saffer, D. M.; McNeill, L. C.; Byrne, T. B.; Araki, E.; Flemings, P. B.; Conin, M.; Eguchi, N. O.; Takahashi, K.; Toczko, S.; Boutt, D. F.; Doan, M.; Kano, Y.; Ito, T.; Lin, W.

2009-12-01

In summer 2009, Integrated Ocean Drilling Program (IODP) Expedition 319 drilled a 1600 m deep riser borehole (Site C0009) in the Kumano Basin offshore SW Japan, to investigate the properties, structure and state of stress in the hanging wall above the subduction plate boundary. The first riser-based scientific drilling in IODP history allowed us to make several new scientific measurements including in situ stress magnitude, pore pressure and permeability using the Modular Formation Dynamics Tester (MDT) wireline tool, and measurement of minimum stress magnitude from Leak-off Tests (LOT). In addition, continuous monitoring of mud weight, mud gas, annular pressure, and mud losses provided data to constrain formation pore fluid pressure and stress. At Site C0009, we conducted 2 LOTs below a casing shoe at 708.6 m depth and 11 successful MDT measurements, including 9 single probe tests to measure pore pressure and fluid mobility and 2 dual packer tests: 1 to measure permeability by a drawdown test, and 1 to measure in situ stress. Measured pore pressures are approximately hydrostatic to 1463.7 m depth. We observed only minor gas shows when drilling ahead (as in-place methane was liberated from the rock at the bit) but little or no gas during pipe connections. This indicates that the borehole mud pressure exceeded the formation pore pressure, and is consistent with the MDT measurements. Permeabilities range from ~10-16 m2 - 10-14 m2, and the observed variation is consistent with lithologic changes defined in gamma ray logs. The MDT measurement at 874.3 mbsf and the LOT at 708.6 m yield values for the least principal stress of 34.8 MPa and 30.2 MPa, respectively. Both are less than the vertical stress (Sv) computed from density logs. Partial mud circulation losses occurred when the borehole mud pressure exceeded the leak-off stress measured at the base of the casing shoe; this provides an additional indirect constraint on Shmin magnitude. Mud pressure slightly in excess of the leak-off stress may have also generated poorly-developed drilling-induced tensile fractures (DITF) observed in resistivity image logs between ~750 - 1000 m. From the presence of DITF, Shmin measurements, and assuming a rock tensile strength of 1 MPa, we determine that SHmax is 35.1 MPa for the MDT stress measurement, and 30.2 MPa for the LOT. Using the MDT measurement of Shmin, the resulting principal stress magnitudes define a strike-slip faulting regime with effective stresses of Shmax’ = 14 MPa, Sv' = 7.3 MPa, and Shmin’ = 6.4 MPa. In contrast, using the LOT measurement of Shmin, the stress magnitudes indicate a normal faulting regime in which Sv’ = 6.2 MPa, Shmax’ = 2.8 MPa, and Shmin’ = 2.6 MPa.

Limited differences in fish and benthic communities and possible cascading effects inside and outside a protected marine area in Sagres (SW Portugal).

PubMed

Gil Fernández, C; Paulo, D; Serrão, E A; Engelen, A H

2016-03-01

Marine protected areas (MPAs) are a relatively recent fisheries management and conservation tool for conservation of marine ecosystems and serve as experimental grounds to assess trophic cascade effects in areas were fishing is restricted to some extent. A series of descriptive field studies were performed to assess fish and benthic communities between two areas within a newly established MPA in SW Portugal. We characterized benthic macroalgal composition and determined the size, density and biomass of the main benthic predatory and herbivorous fish species as well as the main benthic herbivorous invertebrates to assess indications of top-down control on the phytobenthic assemblages. Fish species were identical inside and outside the MPA, in both cases Sarpa salpa was the most abundant fish herbivore and Diplodus spp. accounted for the great majority of the benthic predators. However, size and biomass of D. spp. were higher inside than outside the MPA. The main herbivorous invertebrate was the sea urchin Paracentrotus lividus, which was smaller and predominantly showing a crevice-dwelling behaviour in the MPA. In addition, P. lividus size frequency distribution showed a unimodal pattern outside and a bimodal pattern inside the MPA. We found significant differences in the algal assemblages between inside and outside the MPA, with higher abundance of turf and foliose algae inside, and articulated calcareous and corticated macrophytes outside the MPA, but no differences in the invasive Asparagopsis spp. The obtained results show differences in predatory fish and benthic community structure, but not in species richness, inside and outside the MPA. We hypothesize these differences lead to variation in species interactions: directly through predation and indirectly via affecting sea urchins behavioural patterns, predators might drive changes in macroalgal assemblages via trophic cascade in the study area. However due to non-biological differences between the two areas it is difficult to suggest that the MPA causes increased biological parameters of targeted species and to assess predatory control and trophic cascade effects in areas where fishing pressure is reduced. It is therefor advisable to design MPAs so that their impacts can be scientifically evaluated in a proper fashion. Copyright © 2015 Elsevier Ltd. All rights reserved.

Markedly Enhanced Skeletal Muscle Transfection Achieved by the Ultrasound-Targeted Delivery of Non-Viral Gene Nanocarriers with Microbubbles

PubMed Central

Burke, Caitlin W.; Suk, Jung Soo; Kim, Anthony J.; Hsiang, Yu-Han J.; Klibanov, Alexander L.; Hanes, Justin; Price, Richard J.

2012-01-01

Our goal was to enhance ultrasound (US)-targeted skeletal muscle transfection through the use of poly(ethyleneglycol) (PEG)/polyethylenimine (PEI) nanocomplex gene carriers and adjustments to US and microbubble (MB) parameters. C57BL/6 mice received an intravenous infusion of MBs and either “naked” luciferase plasmid or luciferase plasmid condensed in PEG/PEI nanocomplexes. Pulsed ultrasound (1MHz; 0.6 MPa or 0.8 MPa) was applied to the right hindlimb for 12 mins. Luciferase activity in both hindlimbs was assessed at 3, 5, 7, and 10 days post-treatment by bioluminescent imaging. When targeted to hindlimb using unsorted MBs and 0.6 MPa US, 7 days after treatment, we observed a >60-fold increase in luciferase activity in PEG/PEI nanocomplex treated muscles over muscles treated with “naked” plasmid DNA. Luciferase activity was consistently greater after treatment with PEG/PEI nanocomplexes at 0.6 MPa as compared to 0.8 MPa. The combination of small diameter MBs and 0.6 MPa US also resulted in significantly greater gene expression when compared to concentration matched intramuscular injections, a control condition in which considerably more PEG/PEI nanocomplexes were present in tissue. This result suggests that, in addition to facilitating PEG/PEI nanocomplex delivery from the bloodstream to tissue, US enhances transfection via one or more secondary mechanisms, including increased cellular uptake and/or trafficking to the nucleus of PEG/PEI nanocomplexes. We conclude that PEG/PEI nanocomplexes may be used to markedly enhance the amplitude of US-MB-targeted skeletal muscle transfection and that activating “small” MBs with a moderate level (0.6 MPa) of acoustic pressure can further enhance these effects. PMID:22800583

Proximal pulmonary vascular stiffness as a prognostic factor in children with pulmonary arterial hypertension.

PubMed

Friesen, Richard M; Schäfer, Michal; Ivy, D Dunbar; Abman, Steven H; Stenmark, Kurt; Browne, Lorna P; Barker, Alex J; Hunter, Kendall S; Truong, Uyen

2018-05-16

Main pulmonary artery (MPA) stiffness and abnormal flow haemodynamics in pulmonary arterial hypertension (PAH) are strongly associated with elevated right ventricular (RV) afterload and associated with disease severity and poor clinical outcomes in adults with PAH. However, the long-term effects of MPA stiffness on RV function in children with PAH remain poorly understood. This study is the first comprehensive evaluation of MPA stiffness in children with PAH, delineating the mechanistic relationship between flow haemodynamics and MPA stiffness as well as the prognostic ability of these measures regarding clinical outcomes. Fifty-six children diagnosed with PAH underwent baseline cardiac magnetic resonance (CMR) acquisition and were compared with 23 control subjects. MPA stiffness and wall shear stress (WSS) were evaluated using phase contrast CMR and were evaluated for prognostic potential along with standard RV volumetric and functional indices. Pulse wave velocity (PWV) was significantly increased (2.8 m/s vs. 1.4 m/s, P < 0.0001) and relative area change (RAC) was decreased (25% vs. 37%, P < 0.0001) in the PAH group, correlating with metrics of RV performance. Decreased WSS was associated with a decrease in RAC over time (r = 0.679, P < 0.001). For each unit increase in PWV, there was approximately a 3.2-fold increase in having a moderate clinical event. MPA stiffness assessed by non-invasive CMR was increased in children with PAH and correlated with RV performance, suggesting that MPA stiffness is a major contribution to RV dysfunction. PWV is predictive of moderate clinical outcomes, and may be a useful prognostic marker of disease activity in children with PAH.

Experimental Simulations of Methane Gas Migration through Water-Saturated Sediment Cores

NASA Astrophysics Data System (ADS)

Choi, J.; Seol, Y.; Rosenbaum, E. J.

2010-12-01

Previous numerical simulations (Jaines and Juanes, 2009) showed that modes of gas migration would mainly be determined by grain size; capillary invasion preferably occurring in coarse-grained sediments vs. fracturing dominantly in fine-grained sediments. This study was intended to experimentally simulate preferential modes of gas migration in various water-saturated sediment cores. The cores compacted in the laboratory include a silica sand core (mean size of 180 μm), a silica silt core (1.7 μm), and a kaolin clay core (1.0 μm). Methane gas was injected into the core placed within an x-ray-transparent pressure vessel, which was under continuous x-ray computed tomography (CT) scanning with controlled radial (σr), axial (σa), and pore pressures (P). The CT image analysis reveals that, under the radial effective stress (σr') of 0.69 MPa and the axial effective stress (σa') of 1.31 MPa, fracturings by methane gas injection occur in both silt and clay cores. Fracturing initiates at the capillary pressure (Pc) of ~ 0.41 MPa and ~ 2.41 MPa for silt and clay cores, respectively. Fracturing appears as irregular fracture-networks consisting of nearly invisibly-fine multiple fractures, longitudinally-oriented round tube-shape conduits, or fine fractures branching off from the large conduits. However, for the sand core, only capillary invasion was observed at or above 0.034 MPa of capillary pressure under the confining pressure condition of σr' = 1.38 MPa and σa' = 2.62 MPa. Compared to the numerical predictions under similar confining pressure conditions, fracturing occurs with relatively larger grain sizes, which may result from lower grain-contact compression and friction caused by loose compaction and flexible lateral boundary employed in the experiment.

Stress-dependent permeability and wave dispersion in tight cracked rocks: Experimental validation of simple effective medium models

NASA Astrophysics Data System (ADS)

Sarout, Joel; Cazes, Emilie; Delle Piane, Claudio; Arena, Alessio; Esteban, Lionel

2017-08-01

We experimentally assess the impact of microstructure, pore fluid, and frequency on wave velocity, wave dispersion, and permeability in thermally cracked Carrara marble under effective pressure up to 50 MPa. The cracked rock is isotropic, and we observe that (1) P and S wave velocities at 500 kHz and the low-strain (<10-5) mechanical moduli at 0.01 Hz are pressure-dependent, (2) permeability decreases asymptotically toward a small value with increasing pressure, (3) wave dispersion between 0.01 Hz and 500 MHz in the water-saturated rock reaches a maximum of 26% for S waves and 9% for P waves at 1 MPa, and (4) wave dispersion virtually vanishes above 30 MPa. Assuming no interactions between the cracks, effective medium theory is used to model the rock's elastic response and its permeability. P and S wave velocity data are jointly inverted to recover the crack density and effective aspect ratio. The permeability data are inverted to recover the cracks' effective radius. These parameters lead to a good agreement between predicted and measured wave velocities, dispersion and permeability up to 50 MPa, and up to a crack density of 0.5. The evolution of the crack parameters suggests that three deformation regimes exist: (1) contact between cracks' surface asperities up to 10 MPa, (2) progressive crack closure between 10 and 30 MPa, and (3) crack closure effectively complete above 30 MPa. The derived crack parameters differ significantly from those obtained by analysis of 2-D electron microscope images of thin sections or 3-D X-ray microtomographic images of millimeter-size specimens.

Influence of xanthan gum on the structural characteristics of myofibrillar proteins treated by high pressure.

PubMed

Villamonte, Gina; Jury, Vanessa; Jung, Stéphanie; de Lamballerie, Marie

2015-03-01

The effects of xanthan gum on the structural modifications of myofibrillar proteins (0.3 M NaCl, pH 6) induced by high pressure (200, 400, and 600 MPa, 6 min) were investigated. The changes in the secondary and tertiary structures of myofibrillar proteins were analyzed by circular dichroism. The protein denaturation was also evaluated by differential scanning calorimetry. Likewise, the protein surface hydrophobicity and the solubility of myofibrillar proteins were measured. High pressure (600 MPa) induced the loss of α-helix structures and an increase of β-sheet structures. However, the presence of xanthan gum hindered the former mechanism of protein denaturation by high pressure. In fact, changes in the secondary (600 MPa) and the tertiary structure fingerprint of high-pressure-treated myofibrillar proteins (400 to 600 MPa) were observed in the presence of xanthan gum. These modifications were confirmed by the thermal analysis, the thermal transitions of high-pressure (400 to 600 MPa)-treated myofibrillar proteins were modified in systems containing xanthan gum. As consequence, the high-pressure-treated myofibrillar proteins with xanthan gum showed increased solubility from 400 MPa, in contrast to high-pressure treatment (600 MPa) without xanthan gum. Moreover, the surface hydrophobicity of high-pressure-treated myofibrillar proteins was enhanced in the presence of xanthan gum. These effects could be due to the unfolding of myofibrillar proteins at high-pressure levels, which exposed sites that most likely interacted with the anionic polysaccharide. This study suggests that the role of food additives could be considered for the development of meat products produced by high-pressure processing. © 2015 Institute of Food Technologists®

Intra-articular steroids in knee osteoarthritis: a comparative study of triamcinolone hexacetonide and methylprednisolone acetate.

PubMed

Pyne, Debasish; Ioannou, Yiannakis; Mootoo, Ramesh; Bhanji, Asgar

2004-04-01

The aim of this study was to compare the effectiveness of triamcinolone hexacetonide (THA) and methylprednisolone acetate (MPA), given via the intra-articular route at equipotent dosage to patients with symptomatic knee OA with effusion, in a double-blind randomized comparative trial. Consecutive hospital-referred patients who fulfilled the American College of Rheumatology criteria for knee OA (clinical and radiographic) were randomly allocated to receive either THA 20 mg (1 ml) or MPA 40 mg (1 ml). All patients had synovial fluid aspirated from their knee joint at the time of injection. Assessments were made at 0, 3 and 8 weeks by a second operator, thus blinding both patient and assessor. Outcomes measured at each visit were: knee pain in the previous 48 h (expressed on a 100 mm visual analog scale; VAS), stair climb time (SCT) and Lequesne index score (LEQ). Changes in VAS, SCT and LEQ were compared between the groups using a Student's paired t test. Fifty-seven patients were studied (44 female, 13 male) with a mean age of 62.5 years. Both steroids gave significant pain relief (VAS) at week 3 ( p<0.01) but only MPA showed an effect on VAS and LEQ scores at week 8 compared to baseline ( p<0.05). THA was more effective than MPA at pain reduction at week 3 ( p<0.01); this difference was lost at week 8 ( p=0.17). There was no significant difference between the two drugs in functional endpoints (SCT, LEQ) at either 3 or 8 weeks. Both THA and MPA offer at least temporary symptomatic benefit in knee OA. THA is more effective than MPA at week 3, but its effect is lost by week 8. MPA still has an effect at week 8.

Exploratory Characterization of a Perfluoropolyether Oil as a Possible Viscosity Standard at Deepwater Production Conditions of 533 K and 241 MPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baled, Hseen O.; Tapriyal, Deepak; Morreale, Bryan D.

2013-08-29

DuPont’s perfluoropolyether oil Krytox® GPL 102 is a promising candidate for the high-temperature, high-pressure Deepwater viscosity standard (DVS). The preferred DVS is a thermally stable liquid that exhibits a viscosity of roughly 20 mPa∙s at 533 K and 241 MPa; a viscosity value representative of light oils found in ultra-deep formations beneath the deep waters of the Gulf of Mexico. A windowed rolling-ball viscometer designed by our team is used to determine the Krytox® GPL 102 viscosity at pressures to 245 MPa and temperatures of 311 K, 372 K, and 533 K. At 533 K and 243 MPa, the Krytox®more » GPL 102 viscosity is (27.2±1.3)mPa∙s. The rolling-ball viscometer viscosity results for Krytox® GPL 102 are correlated with an empirical 10-parameter surface fitting function that yields an MAPD of 3.9 %. A Couette rheometer is also used to measure the Krytox® GPL 102 viscosity, yielding a value of (26.2±1)mPa∙s at 533 K and 241 MPa. The results of this exploratory study suggest that Krytox®GPL 102 is a promising candidate for the DVS, primarily because this fluoroether oil is thermally stable and exhibits a viscosity closer to the targeted value of 20 mPa ∙ s at 533 K and 241 MPa than any other fluid reported to date. Finally and nonetheless, further studies must be conducted by other researcher groups using various types of viscometers and rheometers on samples of Krytox GPL® 102 from the same lot to further establish the properties of Krytox GPL® 102.« less

High hydrostatic pressure affects antigenic pool in tumor cells: Implication for dendritic cell-based cancer immunotherapy.

PubMed

Urbanova, Linda; Hradilova, Nada; Moserova, Irena; Vosahlikova, Sarka; Sadilkova, Lenka; Hensler, Michal; Spisek, Radek; Adkins, Irena

2017-07-01

High hydrostatic pressure (HHP) can be used to generate dendritic cell (DC)-based active immunotherapy for prostate, lung and ovarian cancer. We showed here that HHP treatment of selected human cancer cell lines leads to a degradation of tumor antigens which depends on the magnitude of HHP applied and on the cancer cell line origin. Whereas prostate or ovarian cell lines displayed little protein antigen degradation with HHP treatment up to 300MPa after 2h, tumor antigens are hardly detected in lung cancer cell line after treatment with HHP 250MPa at the same time. On the other hand, quick reduction of tumor antigen-coding mRNA was observed at HHP 200MPa immediately after treatment in all cell lines tested. To optimize the DC-based active cellular therapy protocol for HHP-sensitive cell lines the immunogenicity of HHP-treated lung cancer cells at 150, 200 and 250MPa was compared. Lung cancer cells treated with HHP 150MPa display characteristics of immunogenic cell death, however cells are not efficiently phagocytosed by DC. Despite induction of the highest number of antigen-specific CD8 + T cells, 150 MPa-treated lung cancer cells survive in high numbers. This excludes their use in DC vaccine manufacturing. HHP of 200MPa treatment of lung cancer cells ensures the optimal ratio of efficient immunogenic killing and delivery of protein antigens in DC. These results represent an important pre-clinical data for generation of immunogenic killed lung cancer cells in ongoing NSCLC Phase I/II clinical trial using DC-based active cellular immunotherapy (DCVAC/LuCa). Copyright © 2017 European Federation of Immunological Societies. Published by Elsevier B.V. All rights reserved.

The effect of elevated methane pressure on methane hydrate dissociation

USGS Publications Warehouse

Circone, S.; Stern, L.A.; Kirby, S.H.

2004-01-01

Methane hydrate, equilibrated at P, T conditions within the hydrate stability field, was rapidly depressurized to 1.0 or 2.0 MPa and maintained at isobaric conditions outside its stability field, while the extent and rate of hydrate dissociation was measured at fixed, externally maintained temperatures between 250 and 288 K. The dissociation rate decreases with increasing pressure at a given temperature. Dissociation rates at 1.0 MPa parallel the complex, reproducible T-dependence previously observed between 250 and 272 K at 0.1 MPa. The lowest rates were observed near 268 K, such that >50% of the sample can persist for more than two weeks at 0.1 MPa to more than a month at 1 and 2 MPa. Varying the pressure stepwise in a single experiment increased or decreased the dissociation rate in proportion to the rates observed in the isobaric experiments, similar to the rate reversibility previously observed with stepwise changes in temperature at 0.1 MPa. At fixed P, T conditions, the rate of methane hydrate dissociation decreases monotonically with time, never achieving a steady rate. The relationship between time (t) and the extent of hydrate dissociation is empirically described by: Evolved gas (%) = A??tB where the pre-exponential term A ranges from 0 to 16% s-B and the exponent B is generally <1. Based on fits of the dissociation results to Equation 1 for the full range of temperatures (204 to 289 K) and pressures (0.1 to 2.0 MPa) investigated, the derived parameters can be used to predict the methane evolution curves for pure, porous methane hydrate to within ??5%. The effects of sample porosity and the presence of quartz sand and seawater on methane hydrate dissociation are also described using Equation 1.

Anti-Inflammatory Effects of a Mytilus coruscus α-d-Glucan (MP-A) in Activated Macrophage Cells via TLR4/NF-κB/MAPK Pathway Inhibition

PubMed Central

Liu, Fuyan; Zhang, Xiaofeng; Li, Yuqiu; Chen, Qixin; Liu, Fei; Zhu, Xiqiang; Mei, Li; Song, Xinlei; Liu, Xia; Song, Zhigang; Zhang, Jinhua; Zhang, Wen; Ling, Peixue

2017-01-01

The hard-shelled mussel (Mytilus coruscus) has been used as Chinese traditional medicine for thousands of years; however, to date the ingredients responsible for the various beneficial health outcomes attributed to Mytilus coruscus are still unclear. An α-d-Glucan, called MP-A, was isolated from Mytilus coruscus, and observed to exert anti-inflammatory activity in THP-1 human macrophage cells. Specifically, we showed that MP-A treatment inhibited the production of inflammatory markers, including TNF-α, NO, and PGE2, inducible NOS (iNOS), and cyclooxygenase-2 (COX-2), in LPS-activated THP-1 cells. It was also shown to enhance phagocytosis in the analyzed cells, but to severely inhibit the phosphorylation of mitogen-activated protein kinases (MAPKs) and the nuclear translocation of NF-κB P65. Finally, MP-A was found to exhibit a high binding affinity for the cell surface receptor TLR4, but a low affinity for TLR2 and dectin-1, via surface plasmon resonance (SPR) analysis. The study indicates that MP-A suppresses LPS-induced TNF-α, NO and PEG2 production via TLR4/NF-κB/MAPK pathway inhibition, and suggests that MP-A may be a promising therapeutic candidate for diseases associated with TNF-α, NO, and/or PEG2 overproduction. PMID:28930149

Final report on bilateral supplementary comparison APMP.M.P-S5 in hydraulic gauge pressure from 1 MPa to 10 MPa

NASA Astrophysics Data System (ADS)

Yue, J.; Yang, Y.; Sabuga, W.

2016-01-01

This report summarizes the results of the Asia-Pacific Metrology Programme (APMP) supplementary comparison APMP.M.P-S5 for hydraulic gauge pressure in the range of 1 MPa to 10 MPa, which is a bilateral comparison carried out at the National Institute of Metrology, China (NIM) and the Physikalisch-Technische Bundesanstalt, Germany (PTB) during the period June 2014 to June 2015. NIM piloted the comparison and provided the transfer standard, which was a piston-cylinder assembly (PCA) of 1 cm2 nominal effective area built in a hydraulic pressure balance manufactured by Fluke Corporation. The laboratory standards of NIM and PTB are both hydraulic pressure balances equipped with PCAs, of which the nominal effective area is 1 cm2 for NIM and 5 cm2 for PTB. The results of the comparison successfully demonstrated that the hydraulic gauge pressure standards of NIM and PTB in the range of 1 MPa to 10 MPa are equivalent within their claimed uncertainties. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

HHP treatment of liquid egg at 200-350 MPa

NASA Astrophysics Data System (ADS)

Tóth, A.; Németh, Cs; Palotás, P.; Surányi, J.; Zeke, I.; Csehi, B.; Castillo, L. A.; Friedrich, L.; Balla, Cs

2017-10-01

High hydrostatic pressure (HHP) treatment of egg proteins partially limits their sensitivity to pressure. According to the literature, at the 450 MPa level, denaturation of some proteins sets in to the extent that sensory and functional characteristics are impacted. This study involved treating liquid egg (egg white, yolk, and melange) at less than the above-mentioned value, after which the microbiological effect was examined. For the study, pressure pouches were filled with 100ml of raw liquid egg per pouch. Then the samples were treated at 200, 250, 300 and 350 MPa. In each case, the level was reached by increasing pressure at a rate of 100 MPa/min. Measurements were taken at the Corvinus University of Budapest, Faculty of Food Science, Dept. of Refrigeration and Livestock Products Technology RESATO FPU 100-2000 equipment. Denaturation was determined with calorimetric (DSC) tests. From our results, it appears that even at 250 MPa pressure treatment, the viable cell count decreases. Further, it can be said that microbe count went down in the egg white samples at 300-350 MPa, below the impact level. Significant denaturation was not detected during our examinations. In summary, we state that the most HHP-sensitive liquid egg type, egg white, can be pressure treated to reduce microbe count at a level less than that which causes denaturation. Microbe reduction was smaller in yolk and melange, so higher pressure values are appropriate for these products.

Generation of Spatially Aligned Collagen Fiber Networks through Microtransfer Molding

PubMed Central

Naik, Nisarga; Caves, Jeffrey

2013-01-01

The unique biomechanical properties of native tissue are governed by the organization and composition of integrated collagen and elastin networks. We report an approach for fabricating spatially aligned, fiber-reinforced composites (FRC) with adjustable collagen fiber dimensions, layouts, and distribution within an elastin-like protein matrix yielding a biocomposite with controllable mechanical responses. Microtransfer molding is employed for the fabrication of hollow and solid collagen fibers with straight or crimped fiber geometries. Collagen fibers (width: 2 – 50 μm, thickness: 300 nm – 3 μm) exhibit a Young’s modulus of 126 ± 61 MPa and an ultimate tensile strength (UTS) of 7 ± 3.2 MPa. As fiber networks within composite structures, straight fiber layouts display orthotropic responses with Young’s modulus ranging from 0.95 ± 0.35 to 10.4 ± 0.5 MPa and tensile strength from 0.22 ± 0.08 to 0.87 ± 0.5 MPa with increasing fraction of collagen fibers (1–10% v/v). In contrast, composites based on crimped fiber layouts exhibit strain-dependent stiffness with an increase in Young’s modulus from 0.7 ± 0.14 MPa to 3.15 ± 0.49 MPa, at a specific transition strain. Through controlling the microstructure of engineered collagen fiber networks, a facile means has been established to control macroscale mechanical responses of composite protein-based materials. PMID:24039146

Anti-Inflammatory Effects of a Mytilus coruscus α-d-Glucan (MP-A) in Activated Macrophage Cells via TLR4/NF-κB/MAPK Pathway Inhibition.

PubMed

Liu, Fuyan; Zhang, Xiaofeng; Li, Yuqiu; Chen, Qixin; Liu, Fei; Zhu, Xiqiang; Mei, Li; Song, Xinlei; Liu, Xia; Song, Zhigang; Zhang, Jinhua; Zhang, Wen; Ling, Peixue; Wang, Fengshan

2017-09-20

The hard-shelled mussel ( Mytilus coruscus ) has been used as Chinese traditional medicine for thousands of years; however, to date the ingredients responsible for the various beneficial health outcomes attributed to Mytilus coruscus are still unclear. An α-d-Glucan, called MP-A, was isolated from Mytilus coruscus , and observed to exert anti-inflammatory activity in THP-1 human macrophage cells. Specifically, we showed that MP-A treatment inhibited the production of inflammatory markers, including TNF-α, NO, and PGE2, inducible NOS (iNOS), and cyclooxygenase-2 (COX-2), in LPS-activated THP-1 cells. It was also shown to enhance phagocytosis in the analyzed cells, but to severely inhibit the phosphorylation of mitogen-activated protein kinases (MAPKs) and the nuclear translocation of NF-κB P65. Finally, MP-A was found to exhibit a high binding affinity for the cell surface receptor TLR4, but a low affinity for TLR2 and dectin-1, via surface plasmon resonance (SPR) analysis. The study indicates that MP-A suppresses LPS-induced TNF-α, NO and PEG2 production via TLR4/NF-κB/MAPK pathway inhibition, and suggests that MP-A may be a promising therapeutic candidate for diseases associated with TNF-α, NO, and/or PEG2 overproduction.

Effects of Jet Pressure on the Ground Surface Quality and CBN Wheel Wear in Grinding AISI 690 Nickel-Based Superalloy

NASA Astrophysics Data System (ADS)

Guitouni, Ahmed; Chaieb, Iheb; Rhouma, Amir Ben; Fredj, Nabil Ben

2016-11-01

Fluid application in grinding is getting attention as higher stock removal rates, higher surface integrity and longer wheel life are required. It is necessary to define proper conditions of application for meeting high productivity goals by lowering the specific grinding energy and reducing the temperature of the contact zone. The present study investigated the capacity of the jet pressure of a spot nozzle to improve the wear of a CBN wheel when grinding the AISI 690 superalloy. Grinding experiments were conducted with an emulsion-type cooling fluid delivered at pressure ranging from 0.1 to 4 MPa. Results show that the maximum stock removal, reached at 4 MPa, is 5 times the stock removal obtained at 0.1 MPa, while the grinding ratio at 4 MPa is 8 times that at 0.1 MPa, and there is a critical pressure ( P c) around 1.5 MPa corresponding to the minimum specific grinding energy. Scanning electron microscopy of the grain tips showed that the wear mechanism shifts from breaking and dislodgment at low jet pressure to micro-fracture resulting in continuous self-sharpening of the abrasive grains. By lubricating at jet pressure close to P c, there is less thermal damage due to plowing and sliding and the resulting lower loading of the abrasive grains favors the micro-fracture of grains and thus a longer wheel life.

Neighborhood walkability, income, and hour-by-hour physical activity patterns.

PubMed

Arvidsson, Daniel; Eriksson, Ulf; Lönn, Sara Larsson; Sundquist, Kristina

2013-04-01

This study aimed to investigate both the mean daily physical activity and the hour-by-hour physical activity patterns across the day using accelerometry and how they are associated with neighborhood walkability and individual income. Moderate physical activity (MPA) was assessed by accelerometry in 2252 adults in the city of Stockholm, Sweden. Neighborhood walkability (residential density, street connectivity, and land use mix) was objectively assessed within 1000m network buffers around the participants' residence and individual income was self-reported. Living in a high walkability neighborhood was associated with more mean daily MPA compared with living in a low walkability neighborhood on weekdays and weekend days. Hour-by-hour analyses showed that this association appeared mainly in the afternoon/early evening during weekdays, whereas it appeared across the middle of the day during weekend days. Individual income was associated with mean daily MPA on weekend days. On weekdays, the hour-by-hour analyses showed that high income was associated with more MPA around noon and in late afternoon/early evening, whereas low income was associated with more MPA at the hours before noon and in the early afternoon. During the weekend, high income was more consistently associated with higher MPA. Hour-by-hour accelerometry physical activity patterns provides a more comprehensive picture of the associations between neighborhood walkability and individual income and physical activity and the variability of these associations across the day.

Medroxyprogesterone acetate inhibits CD8+ T cell viral specific effector function and induces herpes simplex virus type 1 reactivation

PubMed Central

Cherpes, Thomas L.; Busch, James L.; Sheridan, Brian S.; Harvey, Stephen A. K.; Hendricks, Robert L.

2008-01-01

Clinical research suggests hormonal contraceptive use is associated with increased frequencies of herpes simplex virus (HSV) reactivation and shedding. We examined the effects of medroxyprogesterone acetate (MPA), the compound most commonly used for injectable hormonal contraception, on HSV-1 reactivation and CD8+ T cell function in murine trigeminal ganglia (TG). In ex vivo TG cultures, MPA dramatically inhibited canonical CD8+ T cell effector functions, including IFN-γ production and lytic granule release, and increased HSV-1 reactivation from latency. In vivo, MPA treatment of latently infected ovariectomized mice inhibited IFN-γ production and lytic granule release by TG resident CD8+ T cells stimulated directly ex vivo. RNA specific for the essential immediate early viral gene ICP4 as well as viral genome DNA copy number were increased in mice that received MPA during latency, suggesting that treatment increased in vivo reactivation. The increase in HSV-1 copy number appeared to be the result of a two-tine effect, as MPA induced higher reactivation frequencies from latently infected explanted TG neurons in the presence or absence of CD45+ cells. Our data suggest hormonal contraceptives that contain MPA may promote increased frequency of HSV reactivation from latency through the combinatory effects of inhibiting protective CD8+ T cell responses and by a leukocyte-independent effect on infected neurons. PMID:18606648

Contrast-enhanced magneto-photo-acoustic imaging in vivo using dual-contrast nanoparticles.

PubMed

Qu, Min; Mehrmohammadi, Mohammad; Truby, Ryan; Graf, Iulia; Homan, Kimberly; Emelianov, Stanislav

2014-06-01

By mapping the distribution of targeted plasmonic nanoparticles (NPs), photoacoustic (PA) imaging offers the potential to detect the pathologies in the early stages. However, optical absorption of the endogenous chromophores in the background tissue significantly reduces the contrast resolution of photoacoustic imaging. Previously, we introduced MPA imaging - a synergistic combination of magneto-motive ultrasound (MMUS) and PA imaging, and demonstrated MPA contrast enhancement using cell culture studies. In the current study, contrast enhancement was investigated in vivo using the magneto-photo-acoustic (MPA) imaging augmented with dual-contrast nanoparticles. Liposomal nanoparticles (LNPs) possessing both optical absorption and magnetic properties were injected into a murine tumor model. First, photoacoustic signals were generated from both the endogenous absorbers in the tissue and the liposomal nanoparticles in the tumor. Then, given significant differences in magnetic properties of tissue and LNPs, the magnetic response of LNPs (i.e. MMUS signal) was utilized to suppress the unwanted PA signals from the background tissue and thus improves the PA imaging contrast. In this study, we demonstrated the 3D MPA image of LNP-labeled xenografted tumor in a live animal. Compared to conventional PA imaging, the MPA images show significantly enhanced contrast between the nanoparticle-labeled tumor and the background tissue. Our results suggest the feasibility of MPA for high contrast in vivo mapping of dual-contrast nanoparticles.

Solubility of small-chain carboxylic acids in supercritical carbon dioxide

DOE PAGES

Sparks, Darrell L.; Estevez, L. Antonio; Hernandez, Rafael; ...

2010-07-08

The solubility of heptanoic acid and octanoic acid in supercritical carbon dioxide has been determined at temperatures of (313.15, 323.15, and 333.15) K over a pressure range of (8.5 to 30.0) MPa, depending upon the solute. The solubility of heptanoic acid ranged from a solute concentration of (0.08 ± 0.03) kg • m -3 (T = 323.15 K, p = 8.5 MPa) to (147 ± 0.2) kg • m -3 (T = 323.15 K, p = 20.0 MPa). The lowest octanoic acid solubility obtained was a solute concentration of (0.40 ± 0.1) kg • m -3 (T = 333.15 K,more » p = 10.0 MPa), while the highest solute concentration was (151 ± 2) kg • m -3 (T = 333.15 K, p = 26.7 MPa). In addition, solubility experiments were performed for nonanoic acid in supercritical carbon dioxide at 323.15 K and pressures of (10.0 to 30.0) MPa to add to the solubility data previously published by the authors. In general, carboxylic acid solubility increased with increasing solvent density. The results also showed that the solubility of the solutes decreased with increasing molar mass at constant supercritical-fluid density. Additionally, the efficacy of Chrastil's equation and other density-based models was evaluated for each fatty acid.« less

Numerical fatigue analysis of premolars restored by CAD/CAM ceramic crowns.

PubMed

Homaei, Ehsan; Jin, Xiao-Zhuang; Pow, Edmond Ho Nang; Matinlinna, Jukka Pekka; Tsoi, James Kit-Hon; Farhangdoost, Khalil

2018-04-10

The purpose of this study was to estimate the fatigue life of premolars restored with two dental ceramics, lithium disilicate (LD) and polymer infiltrated ceramic (PIC) using the numerical method and compare it with the published in vitro data. A premolar restored with full-coverage crown was digitized. The volumetric shape of tooth tissues and crowns were created in Mimics ® . They were transferred to IA-FEMesh for mesh generation and the model was analyzed with Abaqus. By combining the stress distribution results with fatigue stress-life (S-N) approach, the lifetime of restored premolars was predicted. The predicted lifetime was 1,231,318 cycles for LD with fatigue load of 1400N, while the one for PIC was 475,063 cycles with the load of 870N. The peak value of maximum principal stress occurred at the contact area (LD: 172MPa and PIC: 96MPa) and central fossa (LD: 100MPa and PIC: 64MPa) for both ceramics which were the most seen failure areas in the experiment. In the adhesive layer, the maximum shear stress was observed at the shoulder area (LD: 53.6MPa and PIC: 29MPa). The fatigue life and failure modes of all-ceramic crown determined by the numerical method seem to correlate well with the previous experimental study. Copyright © 2018 The Academy of Dental Materials. Published by Elsevier Inc. All rights reserved.

Evaluating the fracture toughness and flexural strength of pressable dental ceramics: an in vitro study.

PubMed

Gurram, Ravi; Krishna, C H Vamsi; Reddy, K Mahendranadh; Reddy, G V K Mohan; Shastry, Y Mahadev

2014-12-01

The study was undertaken to evaluate the biaxial flexural strength, biaxial flexural strength after etching with 9 % HF acid and fracture toughness of three commonly used pressable all ceramic core materials. Ninety glass ceramic specimens were fabricated from three commercially available leucite based core ceramic material (1) Esthetic Empress, (2) Cergo, and (3) Performance Plus. Thirty discs of each material were divided into three groups of 10 discs each. Biaxial flexural strength (30 discs,) Biaxial flexural strength for samples treated with 9 % HF acid (30 discs) and fracture toughness (30 discs) were evaluated. Core material Performance Plus had the lowest biaxial strength of 124.89 MPa, Cergo had strength of 152.22 MPa and the highest value of 163.95 was reported for Esthetic Empress. For samples treated 9 % HF, Performance Plus had the lowest biaxial strength of 98.37 MPa, Cergo had strength of 117.42 MPa and the highest value of 143.74 was reported for Esthetic Empress. Core material Performance Plus had the lowest fracture toughness of 1.063 MPa, Cergo had strength of 1.112 MPa and the highest value of 1.225 was reported for Esthetic Empress. The results shows that Esthetic Empress had better mechanical properties compared to Cergo had Performance Plus in relation to the parameters tested.

Microstructure, Tensile and Fatigue Properties of Al-5 wt.%Mg Alloy Manufactured by Twin Roll Strip Casting

NASA Astrophysics Data System (ADS)

Heo, Joon-Young; Baek, Min-Seok; Euh, Kwang-Jun; Lee, Kee-Ahn

2018-04-01

This study investigated the microstructure, tensile and fatigue properties of Al-5 wt.%Mg alloy manufactured by twin roll strip casting. Strips cast as a fabricated (F) specimen and a specimen heat treated (O) at 400 °C/5 h were produced and compared. In the F specimen, microstructural observation discovered clustered precipitates in the center area, while in the O specimen precipitates were relatively more evenly distributed. Al, Al6(Mn, Fe), Mg2Al3 and Mg2Si phases were observed. However, most of the Mg2Al3 phase in the heat-treated O specimen was dissolved. A room temperature tensile test measured yield strength of 177.7 MPa, ultimate tensile strength of 286.1 MPa and elongation of 11.1% in the F specimen and 167.7 MPa (YS), 301.5 MPa (UTS) and 24.6% (EL) in the O specimen. A high cycle fatigue test measured a fatigue limit of 145 MPa in the F specimen and 165 MPa in the O specimen, and the O specimen achieved greater fatigue properties in all fatigue stress conditions. The tensile and fatigue fracture surfaces of the above-mentioned specimens were observed, and this study attempted to investigate the tensile and fatigue deformation behavior of strip cast Al-5 wt.%Mg based on the findings.

[Effect of two-step sintering method on properties of zirconia ceramic].

PubMed

Huang, Hui; Wei, Bin; Zhang, Fu-Qiang; Sun, Jing; Gao, Lian

2008-04-01

To study the influence of two-step sintering method on the sintering property, mechanical properties and microstructure of zirconia ceramic. The nano-size zirconia powder were compacted and divided into two groups, one group for one-step sintering method, another group for two-step sintering method. All samples sintered at different temperature. The relative density, three-bend strength, HV hardness, fracture toughness and microstructure of sintered block were investigated. Two-step sintering method influenced the sintering property and mechanical properties of zirconia ceramic. The maximal relative density was 98.49% at 900 degrees C/1,450 degrees C sintering temperature. There were significant difference of mechanical properties between one-step sintering and two-step sintering, the three-bend strength and fracture toughness declined, hardness increased at two-step sintering. The three-bend strength, HV hardness and fracture toughness reached to maximum value as 1,059.08 MPa +/- 75.24 MPa, 1,377.00 MPa +/- 16.37 MPa and 5.92 MPa x m1/2 +/- 0.37 MPa x m1/2 at 900 degrees C/1,450 degrees C sintering temperature respectively. Microscopy revealed the relationship between the porosity and shapes of grains was correlated to strength of the zirconia ceramics. Despite of the two-step sintering method influences the properties of zirconia, it also is a promising esthetic all-ceramic dental material.

The effect of the addition of sorbitol and glycerol towards the edible film characteristics of the belitung taro starch and the lime leaves as antimicrobial

NASA Astrophysics Data System (ADS)

Asria, Merry; Elizarni, Samah, dan Selfa Dewati

2015-12-01

Plastics have been generally used for food packaging, but plastics using causing environmental problem for as non biodegradable. Resolving the problem need another alternative packaging that environmental friendly such as the edible film as biodegradable packing material. This research intend to determination the effects of sorbitol and glycerol (concentration of 1%, 2%, 3%, and 4%) as addition to the edible film characteristics from the belitung taro starch (Xanthosoma sagitifolium). Lime leaves (Citrus aurantifolia) extract used as an antimicrobial film (2%, 4%, 6%, 8%, and 10% respectively). From the research obtained that using sorbitol has given more rigid and hard film texture, while glycerol provides more elastic and flexible texture. Sorbitol give best performance at 2% where thickness 0.17 mm; tensile strength 41.60 MPa; yield strength 34.28 MPa; modulus of elasticity 7983.71 MPa; and maximum strain 29,8%. While, glycerol (2%) provides thickness 0.18 mm; tensile strength 35.72 MPa; yield strength 30.78 MPa; modulus of elasticity 9065.90 MPa; and maximum strain 14.4% for best performance. SEM and FTIR analysis applied to determine film surface morphology's characterization and determine the functional groups of the film materials. The addition of lime leaves extract as antimicrobial gives the growth inhibition activity against the Staphylococcus aureus bacteria.

Use of three-dimensional finite element models of the lateral ankle ligaments to evaluate three surgical techniques

PubMed Central

Wang, Cheng-Wei; Muheremu, Aikeremujiang; Bai, Jing-Ping

2017-01-01

Objective To compare three surgical techniques for lateral ankle ligament reconstruction using finite element (FE) models. Methods A three-dimensional FE model of the left foot of a healthy volunteer and lateral collateral ligament injury models were developed. Three tendons [one-half of the autologous peroneus longus tendon (PLT), one-half of the peroneus brevis tendon (PBT), and an allogeneic tendon] were used for lateral collateral ligament reconstruction. The ankle varus stress and anterior drawer tests were performed to compare the three surgical techniques. Results The ankle varus stress test showed that the equivalent stresses of the anterior talofibular ligament (ATFL) (84.00 MPa) and calcaneofibular ligament (CFL) (27.01 MPa) were lower in allogeneic tendon reconstruction than in the other two techniques but similar to those of normal individuals (138.48 and 25.90 MPa, respectively). The anterior drawer test showed that the equivalent stresses of the ATFL and CFL in autologous PLT reconstruction (31.31 and 28.60 MPa, respectively) and PBT reconstruction (31.47 and 29.07 MPa, respectively) were lower than those in allogeneic tendon reconstruction (57.32 and 52.20 MPa, respectively). Conclusions The allogeneic tendon reconstruction outcome was similar to normal individuals. Allogeneic tendon reconstruction may be superior for lateral ankle ligament reconstruction without considering its complications. PMID:29239256

Contrast-enhanced magneto-photo-acoustic imaging in vivo using dual-contrast nanoparticles☆

PubMed Central

Qu, Min; Mehrmohammadi, Mohammad; Truby, Ryan; Graf, Iulia; Homan, Kimberly; Emelianov, Stanislav

2014-01-01

By mapping the distribution of targeted plasmonic nanoparticles (NPs), photoacoustic (PA) imaging offers the potential to detect the pathologies in the early stages. However, optical absorption of the endogenous chromophores in the background tissue significantly reduces the contrast resolution of photoacoustic imaging. Previously, we introduced MPA imaging – a synergistic combination of magneto-motive ultrasound (MMUS) and PA imaging, and demonstrated MPA contrast enhancement using cell culture studies. In the current study, contrast enhancement was investigated in vivo using the magneto-photo-acoustic (MPA) imaging augmented with dual-contrast nanoparticles. Liposomal nanoparticles (LNPs) possessing both optical absorption and magnetic properties were injected into a murine tumor model. First, photoacoustic signals were generated from both the endogenous absorbers in the tissue and the liposomal nanoparticles in the tumor. Then, given significant differences in magnetic properties of tissue and LNPs, the magnetic response of LNPs (i.e. MMUS signal) was utilized to suppress the unwanted PA signals from the background tissue thus improving the PA imaging contrast. In this study, we demonstrated the 3D MPA imaging of LNP-labeled xenografted tumor in a live animal. Compared to conventional PA imaging, the MPA imaging show significantly enhanced contrast between the nanoparticle-labeled tumor and the background tissue. Our results suggest the feasibility of MPA imaging for high contrast in vivo mapping of dual-contrast nanoparticles. PMID:24653976

Tensile and creep deformation of a newly developed Ni-Fe-based superalloy for 700 °C advanced ultra-supercritical boiler applications

NASA Astrophysics Data System (ADS)

Yuan, Y.; Zhong, Z. H.; Yu, Z. S.; Yin, H. F.; Dang, Y. Y.; Zhao, X. B.; Yang, Z.; Lu, J. T.; Yan, J. B.; Gu, Y.

2015-07-01

A new Ni-Fe-based superalloy, HT-X, has been developed for applications in 700 °C advanced ultra-supercritical (A-USC) boilers. The HT-X alloy is subjected to various heat treatments. Tensile tests are conducted at room temperature (RT), 700 °C and 750 °C. Creep tests are carried out under conditions of 700 °C/300 MPa and 750 °C/150 MPa. After aging treatment, the yield strength of the HT-X alloy at RT and 750 °C is 787 MPa and 624 MPa, respectively. When additional thermal exposure at 750 °C for 5400 h is applied, the yield strength is decreased to 656 MPa at RT and 480 MPa at 700 °C. For an aged specimen, the a/2<110>dislocation shearing process occurs when tensile testing is conducted at RT and 750 °C. As the γ' precipitate size increases in the specimen that is thermally exposed at 750 °C for 5400 h, Orowan bowing is the dominant dislocation process, and stacking faults develop in the γ' precipitates at both RT and 700 °C. Dislocation slip combined with climb is the dominant mechanism under the creep testing conditions. The factors that affect the mechanical properties and deformation mechanisms are discussed.

Cellulose nanofiber board.

PubMed

Yousefi, Hossein; Azad, Sona; Mashkour, Mahdi; Khazaeian, Abolghasem

2018-05-01

A cellulose nanofiber board (CNF-board) with a nominal thickness of 3 mm was fabricated without adhesive or additive. To provide comparison, a cellulose fiber board (CF-board) was also fabricated. A novel cold pre-press apparatus was made to dewater highly absorbent CNF gel prior to drying. A mild drying condition in the vacuum oven at 70 °C and 0.005 MPa was enough to provide the CNF-board with a density of 1.3 g/cm 3 thanks to its self-densification capability. Unlike the CF-board, the fabricated CNF-board had a high water-activated dimensional recovery ratio (averagely 96%) during the five cyclic wetting-drying process. The flexural and tensile strengths of CNF-board obtained were 162 MPa and 85 MPa, respectively. The corresponding values for CF-board were 28 MPa and 11 MPa, respectively. The specific flexural and tensile strengths of CNF-board obtained were higher than those of CF-board as well as some other traditional wood-based composites, polymers and structural ASTM A36 steel. Copyright © 2018 Elsevier Ltd. All rights reserved.

High hydrostatic pressure processing: a method having high success potential in pollen protein extraction

NASA Astrophysics Data System (ADS)

Murat Altuner, Ergin; Çeter, Talip; Alpas, Hami

2012-06-01

Even a single peptide that is present in the pollen wall and cytoplasm could cause pollen allergy. To produce skin-prick test kits, the first step is the extraction of these molecules. In this study, Cedrus atlantica pollens were subjected to 220 and 330 MPa for 10 and 30 min in order to extract these molecules. After high hydrostatic pressure processing (HHPP), the total amounts of proteins (TAPs) are measured and compared with the results of the conventional extraction method (CEM). As a result, the TAPs extracted by HHPP is 18.0210 μ g/mL at 220 MPa for 10 min, 22.5770 μ g/mL at 220 MPa for 30 min, 23.3810 μ g/mL at 330 MPa for 10 min and 25.9270 μ g/mL at 330 MPa for 30 min, while this is 1.9460 μ g/mL in 24 h by the CEM. In addition to these results, visual pollen deformation and eruption, pollen wall and surface damage have also been observed.

High hydrostatic pressure (HHP) effects on antigenicity and structural properties of soybean β-conglycinin.

PubMed

Xi, Jun; He, Mengxue

2018-02-01

In this study, the effect of high hydrostatic pressure (HHP) on antigenicity, free sulfhydryl group (SH) content, hydrophobicity (Ho), fluorescence intensity and circular dichroism data of soybean β-conglycinin was studied. The antigenicity of soybean β-conglycinin was decreased significantly at pressures 200-400 MPa. The antigenicity inhibition rate of β-conglycinin declined from 92.72 to 55.15%, after being treated at 400 MPa for 15 min. Results indicated that free sulphydryl (SH) groups and surface Ho of β-conglycinin were significantly increased at pressures 200-400 MPa and 5-15 min, whereas these properties decreased at the treatments above 400 MPa and 15 min. The maximum fluorescence intensity was noticed at 400 MPa and 15 min. The circular dichroism data analysis revealed that the amount of β-turns and unordered structure significantly increased, while the content of α-helix1 and β-strand1 noticeably decreased. These results provide evidence that HHP-induced the structural modification of β-conglycinin and could alter the antigenicity of β-conglycinin.

Thermal Resistance Variations of Fly Ash Geopolymers: Foaming Responses

NASA Astrophysics Data System (ADS)

Cheng-Yong, Heah; Yun-Ming, Liew; Abdullah, Mohd Mustafa Al Bakri; Hussin, Kamarudin

2017-03-01

This paper presents a comparative study of the characteristic of unfoamed and foamed geopolymers after exposure to elevated temperatures (200-800 °C). Unfoamed geopolymers were produced with Class F fly ash and sodium hydroxide and liquid sodium silicate. Porous geopolymers were prepared by foaming with hydrogen peroxide. Unfoamed geopolymers possessed excellent strength of 44.2 MPa and degraded 34% to 15 MPa in foamed geopolymers. The strength of unfoamed geopolymers decreased to 5 MPa with increasing temperature up to 800 °C. Foamed geopolymers behaved differently whereby they deteriorated to 3 MPa at 400 °C and increased up to 11 MPa at 800 °C. Even so, the geopolymers could withstand high temperature without any disintegration and spalling up to 800 °C. The formation of crystalline phases at higher temperature was observed deteriorating the strength of unfoamed geopolymers but enhance the strength of foamed geopolymers. In comparison, foamed geopolymer had better thermal resistance than unfoamed geopolymers as pores provide rooms to counteract the internal damage.

Flat growth of 7075, 7475, 7050 and 7049 aluminum alloy plate in stress corrosion environments: 2-year marine atmosphere results

NASA Technical Reports Server (NTRS)

Dorward, R. C.; Hasse, K. R.

1978-01-01

Marine atmospheric exposure of smooth and precracked specimens from 7075, 7475, 7050 and 7049 plates support the conclusion that for a given strength level, the short transverse stress corrosion resistance of 7050-T7X and 7049-T7X is superior to that of 7075-T7X. The threshold stress intensity (K sub Iscc) for these alloys is about 25 MPa square root m at a yield strength of about 460 MPa; the corresponding yield strength level for 7075-T7X at this SCR level is about 425 MPa. Additional tests on two lots of high-toughness 7475 plate indicate that this alloy is capable of achieving K sub Iscc values of about 35 MPa square root m at yield strengths of 400-450 MPa. Precracked specimens from all these 7XXX-series alloys are subject to self loading from corrosion product wedging. This effect causes stress corrosion cracks to continue growing at very low apparent stress intensities, and should therefore be considered a potential driving force for stress corrosion in design and materials selection.

Hyperbaric storage of melon juice at and above room temperature and comparison with storage at atmospheric pressure and refrigeration.

PubMed

Queirós, Rui P; Santos, Mauro D; Fidalgo, Liliana G; Mota, Maria J; Lopes, Rita P; Inácio, Rita S; Delgadillo, Ivonne; Saraiva, Jorge A

2014-03-15

Hyperbaric storage (8h) of melon juice (a highly perishable food) at 25, 30 and 37°C, under pressure at 25-150 MPa was compared with atmospheric pressure storage (0.1 MPa) at the same temperatures and under refrigeration (4°C). Comparatively to the refrigerated condition, hyperbaric storage at 50/75 MPa resulted in similar or lower microbial counts (total aerobic mesophiles, enterobacteriaceae, and yeasts/moulds) while at 100/150 MPa, the counts were lower for all the tested temperatures, indicating in the latter case, in addition to microbial growth inhibition, a microbial inactivation effect. At 25 MPa no microbial inhibition was observed. Physicochemical parameters of all samples stored under pressure (pH, titratable acidity, total soluble solids, browning degree and cloudiness) did not show a clear variation trend with pressure, being the results globally similar to refrigeration storage. These results show the potential of hyperbaric storage, at and above room temperature and with potential energy savings, comparatively to refrigeration. Copyright © 2013 Elsevier Ltd. All rights reserved.

Treatment and prevention of music performance anxiety.

PubMed

Spahn, Claudia

2015-01-01

Music performance anxiety (MPA) regularly occurs when musicians present themselves before an audience in performance situations, and thus, it plays an important role in the careers of professional musicians. MPA is expressed on the emotional and physical level, as well as on the levels of thinking and behavior, and extends along a continuum of varying severity. Its performance-impairing, afflicting form is considered to be a specific type of social phobia, which requires therapy. There are different psychological theories, which contribute to the understanding of the phenomenon of MPA and provide basic principles for the various treatment approaches. Current "best practice," in our clinical experience, is a personal- and problem-oriented approach within a multimodal therapy model, including the range of psychoanalytic and cognitive behavioral therapies, body-oriented methods, and mental techniques. In order to avoid severe MPA, prevention in the field of music pedagogic is very important. Thus, the concepts of dealing positively with MPA should be implemented very early into the instrumental and vocal education of musicians. © 2015 Elsevier B.V. All rights reserved.

The application of high pressure-mild temperature processing for prolonging the shelf-life of strawberry purée

NASA Astrophysics Data System (ADS)

Marszałek, K.; Woźniak, Ł.; Skąpska, S.

2016-04-01

The aim of this study was to monitor the shelf-life and quality of strawberry purée preserved using combined high pressure processing (HPP)-mild temperature processing at 300 and 600 MPa for 15 min during cold storage (6°C). Increasing the pressure resulted in a prolonged shelf-life of from 4 to 28 weeks for HPP-preserved purée at 300 and 600 MPa, respectively. The highest inactivation of peroxidases, pectinesterases and polygalacturonases was noted when a higher pressure was used, whereas a lower pressure was more efficient for polyphenoloxidases. The degradation of vitamin C and anthocyanins was 20% and 5% higher at 600 MPa than at 300 MPa, respectively. Significantly fewer changes in the colour coefficient, expressed as ΔE, and the browning index, were observed in purée preserved at 600 MPa. Oxidative and hydrolytic enzymes are highly pressure-resistant, which suggests other inhibitors should be used to increase the shelf-life of good-quality fruit products.

Thermal Resistance Variations of Fly Ash Geopolymers: Foaming Responses

PubMed Central

Cheng-Yong, Heah; Yun-Ming, Liew; Abdullah, Mohd Mustafa Al Bakri; Hussin, Kamarudin

2017-01-01

This paper presents a comparative study of the characteristic of unfoamed and foamed geopolymers after exposure to elevated temperatures (200–800 °C). Unfoamed geopolymers were produced with Class F fly ash and sodium hydroxide and liquid sodium silicate. Porous geopolymers were prepared by foaming with hydrogen peroxide. Unfoamed geopolymers possessed excellent strength of 44.2 MPa and degraded 34% to 15 MPa in foamed geopolymers. The strength of unfoamed geopolymers decreased to 5 MPa with increasing temperature up to 800 °C. Foamed geopolymers behaved differently whereby they deteriorated to 3 MPa at 400 °C and increased up to 11 MPa at 800 °C. Even so, the geopolymers could withstand high temperature without any disintegration and spalling up to 800 °C. The formation of crystalline phases at higher temperature was observed deteriorating the strength of unfoamed geopolymers but enhance the strength of foamed geopolymers. In comparison, foamed geopolymer had better thermal resistance than unfoamed geopolymers as pores provide rooms to counteract the internal damage. PMID:28345643

Impact of Exposure to Pressure of 50 MPa on the Specific Surface Area of Clay

NASA Astrophysics Data System (ADS)

Koszela-Marek, Ewa

2017-12-01

The paper presents results of laboratory tests conducted to determine the impact of pressure of 50 MPa on specific surface area of clay. These tests were carried out in an original, high-pressure test stand. The specific surface area of clay extracted directly from an open pit mine was compared with the specific surface area of the same clay subjected to the pressure of 50 MPa in a high-pressure chamber. The study found that the specific surface area of the clay subjected to the pressure of 50 MPa increased distinctly by over 35 %. The increase in specific surface can be a result of changes in the microstructure of clay particles and microstructural alteration in the soil skeleton, caused by the pressure.

Apparatus for accurate density measurements of fluids based on a magnetic suspension balance

NASA Astrophysics Data System (ADS)

Gong, Maoqiong; Li, Huiya; Guo, Hao; Dong, Xueqiang; Wu, J. F.

2012-06-01

A new apparatus for accurate pressure, density and temperature (p, ρ, T) measurements over wide ranges of (p, ρ, T) (90 K to 290 K; 0 MPa to 3 MPa; 0 kg/m3 to 2000 kg/m3) is described. This apparatus is based on a magnetic suspension balance which applies the Archimedes' buoyancy principle. In order to verify the new apparatus, comprehensive (p, ρ, T) measurements on pure nitrogen were carried out. The maximum relative standard uncertainty is 0.09% in density. The maximum standard uncertainty in temperature is 5 mK, and that in pressure is 250 Pa for 1.5 MPa and 390 Pa for 3MPa full scale range respectively. The experimental data were compared with selected literature data and good agreements were found.

High pressure extraction of phenolic compounds from citrus peels†

NASA Astrophysics Data System (ADS)

Casquete, R.; Castro, S. M.; Villalobos, M. C.; Serradilla, M. J.; Queirós, R. P.; Saraiva, J. A.; Córdoba, M. G.; Teixeira, P.

2014-10-01

This study evaluated the effect of high pressure processing on the recovery of high added value compounds from citrus peels. Overall, the total phenolic content in orange peel was significantly (P < .05) higher than that in lemon peel, except when pressure treated at 500 MPa. However, lemon peel demonstrated more antioxidant activity than orange peel. Pressure-treated samples (300 MPa, 10 min; 500 MPa, 3 min) demonstrated higher phenolic content and antioxidant activity comparatively to the control samples. For more severe treatments (500 MPa, 10 min), the phenolic content and antioxidant activity decreased in both lemon and orange peels. This paper was presented at the 8th International Conference on High Pressure Bioscience & Biotechnology (HPBB 2014), in Nantes (France), 15-18 July 2014.

Biomechanical analysis of a new carbon fiber/flax/epoxy bone fracture plate shows less stress shielding compared to a standard clinical metal plate.

PubMed

Bagheri, Zahra S; Tavakkoli Avval, Pouria; Bougherara, Habiba; Aziz, Mina S R; Schemitsch, Emil H; Zdero, Radovan

2014-09-01

Femur fracture at the tip of a total hip replacement (THR), commonly known as Vancouver B1 fracture, is mainly treated using rigid metallic bone plates which may result in "stress shielding" leading to bone resorption and implant loosening. To minimize stress shielding, a new carbon fiber (CF)/Flax/Epoxy composite plate has been developed and biomechanically compared to a standard clinical metal plate. For fatigue tests, experiments were done using six artificial femurs cyclically loaded through the femoral head in axial compression for four stages: Stage 1 (intact), stage 2 (after THR insertion), stage 3 (after plate fixation of a simulated Vancouver B1 femoral midshaft fracture gap), and stage 4 (after fracture gap healing). For fracture fixation, one group was fitted with the new CF/Flax/Epoxy plate (n = 3), whereas another group was repaired with a standard clinical metal plate (Zimmer, Warsaw, IN) (n = 3). In addition to axial stiffness measurements, infrared thermography technique was used to capture the femur and plate surface stresses during the testing. Moreover, finite element analysis (FEA) was performed to evaluate the composite plate's axial stiffness and surface stress field. Experimental results showed that the CF/Flax/Epoxy plated femur had comparable axial stiffness (fractured = 645 ± 67 N/mm; healed = 1731 ± 109 N/mm) to the metal-plated femur (fractured = 658 ± 69 N/mm; healed = 1751 ± 39 N/mm) (p = 1.00). However, the bone beneath the CF/Flax/Epoxy plate was the only area that had a significantly higher average surface stress (fractured = 2.10 ± 0.66 MPa; healed = 1.89 ± 0.39 MPa) compared to bone beneath the metal plate (fractured = 1.18 ± 0.93 MPa; healed = 0.71 ± 0.24 MPa) (p < 0.05). FEA bone surface stresses yielded peak of 13 MPa at distal epiphysis (stage 1), 16 MPa at distal epiphysis (stage 2), 85 MPa for composite and 129 MPa for metal-plated femurs at the vicinity of nearest screw just proximal to fracture (stage 3), 21 MPa for composite and 24 MPa for metal-plated femurs at the vicinity of screw farthest away distally from fracture (stage 4). These results confirm that the new CF/Flax/Epoxy material could be a potential candidate for bone fracture plate applications as it can simultaneously provide similar mechanical stiffness and lower stress shielding (i.e., higher bone stress) compared to a standard clinical metal bone plate.

A Procedure for Assessing the Structure of the CPF Considering the Loss of Strength Due to Corrosion

DTIC Science & Technology

1999-04-01

Model . . . . . . . A Typical Model Crossection Showing Strakes, Girders and Endpoints The Tranverse Bulkheads in the MAESTRO Model . . . . . . . 14...results show a tranverse redistribution of the the stress concentration found in the MAESTRO model, with the maximum of 261 MPa 5 occurring in the grid...of 350 MPa. The tranverse plate at the junction 7 with the superstructure reached a stress of -271 MPa in a material with a yield strength of 700

Microscopic Polyangiitis

MedlinePlus

... but possess sufficient differences as to justify separate classifications. Who gets Microscopic Polyangiitis? A typical patient MPA can affect individuals from all ethnic backgrounds and any age group. In the United States, the typical MPA patient ...

Preservation of rat hearts in subfreezing temperature isochoric conditions to - 8 °C and 78 MPa.

PubMed

Wan, Lili; Powell-Palm, Matthew J; Lee, Charles; Gupta, Anshal; Weegman, Bradley P; Clemens, Mark G; Rubinsky, Boris

2018-02-12

Isochoric (constant volume) preservation at subfreezing temperatures is being investigated as a novel method for preserving cells and organs. This study is a first initial effort to evaluate the efficacy of this method for heart preservation, and to provide a preliminary outline of appropriate preservation parameters. To establish a baseline for further studies, rat hearts were preserved in a University of Wisconsin (UW) intracellular solution for one hour under isochoric conditions at: 0 °C (atmospheric pressure - 0.1 MPa), - 4 °C (41 MPa), - 6 °C (60 MPa) and - 8 °C (78 MPa). The viability of the heart was evaluated using Langendorff perfusion and histological examination. The physiological performance of hearts preserved at - 4 °C (41 MPa) was comparable to that of a heart preserved on ice at atmospheric pressure, with no statistically significant difference in histological injury score. However, hearts preserved at -4 °C displayed substantially reduced interstitial edema compared to hearts preserved by conventional hypothermic preservation in UW on ice at atmospheric pressure, suggesting significant protection from increased vascular permeability following preservation. Hearts preserved at - 6 °C (60 MPa) suffered injury from cellular swelling and extensive edema, and at - 8 °C (78 MPa) hearts experienced significant morphological disruption. To the best of our knowledge, this is the first publication showing that a mammalian organ can survive low subfreezing temperatures without the use of a cryoprotective additive. Lowering the preservation temperature reduces metabolism and improves preservation quality, and these results suggest that improvements in preservation are possible at subzero temperatures with low to moderate pressures observed at -4 °C. Notably, tissue damage was observed at lower temperatures (-6 °C or below) accompanying further elevation of pressure associated with isochoric preservation that may prove detrimental. Therefore, subfreezing temperature isochoric preservation protocols should optimize, a combination of temperature and pressure that will minimize the negative effects of elevated pressure while retaining the beneficial effect of lower temperatures and reduced metabolism. Copyright © 2018. Published by Elsevier Inc.

Effectiveness and biological compatibility of different generations of dentin adhesives.

PubMed

da Silva, João M F; Rodrigues, José R; Camargo, Carlos H R; Fernandes, Virgilio Vilas Boas; Hiller, Karl-Anton; Schweikl, Helmut; Schmalz, Gottfried

2014-01-01

Besides possessing good mechanical properties, dental materials should present a good biological behavior and should not injure the involved tissues. Bond strength and biocompatibility are both highly significant properties of dentin adhesives. For that matter, these properties of four generations of adhesive systems (Multi-Purpose/Single Bond/SE Plus/Easy Bond) were evaluated. Eighty bovine teeth had their dentin exposed (500- and 200-μm thickness). Adhesive was applied on the dentin layer of each specimen. Following that, the microshearing test was performed for all samples. A dentin barrier test was used for the cytotoxicity evaluation. Cell cultures (SV3NeoB) were collected from testing materials by means of 200- or 500-μm-thick dentin slices and placed in a cell culture perfusion chamber. Cell viability was measured 24 h post-exposition by means of a photometrical test (MTT test). The best bonding performance was shown by the single-step adhesive Easy Bond (21 MPa, 200 μm; 27 MPa, 500 μm) followed by Single Bond (15.6 MPa, 200 μm; 23.4 MPa, 500 μm), SE Plus (18.2 MPa, 200 μm; 20 MPa, 500 μm), and Multi-Purpose (15.2 MPa, 200 μm; 17.9 MPa, 500 μm). Regarding the cytotoxicity, Multi-Purpose slightly reduced the cell viability to 92% (200 μm)/93% (500 μm). Single Bond was reasonably cytotoxic, reducing cell viability to 71% (200 μm)/64% (500 μm). The self-etching adhesive Scotchbond SE decreased cell viability to 85% (200 μm)/71% (500 μm). Conversely, Easy Bond did not reduce cell viability in this test, regardless of the dentin thickness. Results showed that the one-step system had the best bond strength performance and was the least toxic to pulp cells. In multiple-step systems, a correct bonding technique must be done, and a pulp capping strategy is necessary for achieving good performance in both properties. The study showed a promising system (one-step self-etching), referring to it as a good alternative for specific cases, mainly due to its technical simplicity and good biological responses.

Shear bond strength of different types of adhesive systems to dentin and enamel of deciduous teeth in vitro.

PubMed

Kensche, A; Dähne, F; Wagenschwanz, C; Richter, G; Viergutz, G; Hannig, C

2016-05-01

The present study aimed to evaluate the suitability of self-etch adhesives for restoration of deciduous teeth compared with etch and rinse approaches. One hundred twenty primary teeth were divided into five groups, each being assigned to an adhesive system. Self-etch adhesives XenoV (XV) and Clearfil S(3) Bond (CB), Prime&Bond NT with (PBE)/without preliminary etching (PBN), and Optibond FL (OBFL) as an etch and rinse system were included. Enamel and dentin specimens were prepared (n = 36/group), adhesives applied, and compomer cylinders polymerized. After 24-h storage in 37 °C distilled water and thermo-cycling (1440 cycles, 5/55 °C, 27 s), shear bond tests and fracture mode classification based on SEM investigation were performed. Statistical analysis involved ANOVA and Scheffé procedure with Bonferroni-Holm correction (p ≤ 0.005). High shear bond strengths to primary enamel were determined for PBE (mean [M] = 22.48 ± 7.7 MPa) > OBFL (M = 19.06 ± 5.62 MPa) > CB (M = 17.6 ± 6.55 MPa), and XV (M = 16.85 ± 5.38 MPa) and PBN (M = 8.26 ± 4.46 MPa) formed significantly less reliable enamel-resin interfaces (p ≤ 0.005). PBE generated the highest bond strength on primary dentin (M = 21.97 ± 8.02 MPa); significantly lower values were measured for XV (M = 13.44 ± 5.43 MPa) and OBFL (M = 12.92 ± 4.31 MPa) (p ≤ 0.005). Adhesives requiring preliminary etching ensure optimal bond strength to primary enamel. If separate etching is to be avoided, selected self-etch adhesives obtain acceptable shear bond values on primary enamel and dentin. The treatment of pediatric patients presents a great challenge in dental practice, and optimization of treatment processes is important.

CVD silicon carbide monofilament reinforced SrO-Al2O3-2SiO2 (SAS) glass-ceramic composites

NASA Technical Reports Server (NTRS)

Bansal, Narottam P.

1995-01-01

Unidirectional CVD SiC fiber-reinforced SrO.Al2O3.2SiO2 (SAS) glass-ceramic matrix composites have been fabricated by hot pressing at various combinations of temperature, pressure and time. Both carbon-rich surface coated SCS-6 and uncoated SCS-0 fibers were used as reinforcements. Almost fully dense composites have been obtained. Monoclinic celsian, SrAl2Si2O8, was the only crystalline phase observed in the matrix from x-ray diffraction. During three point flexure testing of composites, a test span to thickness ratio of approximately 25 or greater was necessary to avoid sample delamination. Strong and tough SCS-6/SAS composites having a first matrix crack stress of approximately 300 MPa and an ultimate bend strength of approximately 825 MPa were fabricated. No chemical reaction between the SCS-6 fibers and the SAS matrix was observed after high temperature processing. The uncoated SCS-0 fiber-reinforced SAS composites showed only limited improvement in strength over SAS monolithic. The SCS-0/SAS composite having a fiber volume fraction of 0.24 and hot pressed at 1400 deg C exhibited a first matrix cracking stress of approximately 231 +/- 20 MPa and ultimate strength of 265 +/- 17 MPa. From fiber push-out tests, the fiber/matrix interfacial debonding strength (tau(sub debond)) and frictional sliding stress (tau(sub friction)) in the SCS-6/SAS system were evaluated to be approximately 6.7 +/- 2.3 MPa and 4.3 +/- 0.6 MPa, respectively, indicating a weak interface. However, for the SCS-0/SAS composite, much higher values of approximately 17.5 +/- 2.7 MPa for tau(sub debond) and 11.3 +/- 1.6 MPa for tau(sub friction) respectively, were observed; some of the fibers were so strongly bonded to the matrix that they could not be pushed out. Examination of fracture surfaces revealed limited short pull-out length of SCS-0 fibers. The applicability of various micromechanical models for predicting the values of first matrix cracking stress and ultimate strength of these composites were examined.

A four-tier classification system of pulmonary artery metrics on computed tomography for the diagnosis and prognosis of pulmonary hypertension.

PubMed

Truong, Quynh A; Bhatia, Harpreet Singh; Szymonifka, Jackie; Zhou, Qing; Lavender, Zachary; Waxman, Aaron B; Semigran, Marc J; Malhotra, Rajeev

We aimed to develop a severity classification system of the main pulmonary artery diameter (mPA) and its ratio to the ascending aorta diameter (ratio PA) for the diagnosis and prognosis of pulmonary hypertension (PH) on computed tomography (CT) scans. In 228 patients (136 with PH) undergoing right heart catheterization (RHC) and CT for dyspnea, we measured mPA and ratio PA. In a derivation cohort (n = 114), we determined cutpoints for a four-tier severity grading system that would maximize sensitivity and specificity, and validated it in a separate cohort (n = 114). Cutpoints for mPA were defined with ≤27 mm(F) and ≤29 mm(M) as the normal reference range; mild as >27 to <31 mm(F) and >29 to <31 mm(M); moderate≥31-34 mm; and severe>34 mm. Cutpoints for ratio PA were defined as normal ≤0.9; mild>0.9 to 1.0; moderate>1.0 to 1.1; and severe>1.1. Sensitivities for normal tier were 99% for mPA and 93% for ratio PA; while specificities for severe tier were 98% for mPA>34 mm and 100% for ratio PA>1.1. C-statistics for four-tier mPA and ratio PA were both 0.90 (derivation) and both 0.85 (validation). Severity of mPA and ratio PA corresponded to hemodynamics by RHC and echocardiography (both p < 0.001). Moderate-severe mPA values of ≥31 mm and ratio PA>1.1 had worse survival than normal values (all p ≤ 0.01). A CT-based four-tier severity classification system of PA diameter and its ratio to the aortic diameter has high accuracy for PH diagnosis with increased mortality in patients with moderate-severe severity grades. These results may support clinical utilization on chest and cardiac CT reports. Copyright © 2018 Society of Cardiovascular Computed Tomography. Published by Elsevier Inc. All rights reserved.

Inverse modeling of the overpressure distribution in an extension fracture with an arbitrary aperture variation: application to non-feeder dikes in the Miyake-jima Volcano, Japan

NASA Astrophysics Data System (ADS)

Kusumoto, Shigekazu; Geshi, Nobuo; Gudmundsson, Agust

2010-05-01

We derived a solution for the overpressure distribution acting on the walls (surfaces) of an extension fracture (a hydrofracture) with an arbitrary opening-displacement (or aperture) variation. In the proposed model, we assume that the overpressure distribution can be described by Fourier cosine series. We at first present a solution for the forward model giving the fracture aperture when it is opened by an irregular overpressure variation obtained using the Fourier cosine series. Next, by changing the form of the solution for the forward model, we obtain a matrix equation that can be used to estimate the Fourier coefficients to obtain the overpressure distribution from the fracture aperture variation. As simple examples of this inverse analysis, we estimate the overpressure conditions from crack apertures given analytically for two cases, namely, 1) the overpressure in the crack is constant, and 2) the overpressure variation in the crack varies linearly from its center. The estimated overpressure distributions were found to be correct, although a small 'noise' was present. Since the method presented here gives the overpressure distribution as a Fourier series by the aperture data measured at a finite number of points, the overpressure conditions for forming the fracture can be determined for each wavelength. The Fourier coefficient of n = 0 is an important coefficient that gives the average value of the overpressure acting inside the crack. With the exception of n = 0, the Fourier coefficient of n = 1 expresses the longest wavelength component of the irregular overpressure. Thus, because this coefficient including the coefficient of n = 0 gives the longest wavelength component in the irregular overpressure, the component may be an important indicator of the overpressure condition that decides the basic form of the crack. We applied the solution for the inverse analysis to the thickness data of 19 non-feeder dikes exposed in the caldera wall of the Miyake-jima Volcano, Japan. In the analysis, the host-rock Young's modulus and Poisson's ratio were taken as 1 GPa and 0.25. The results show that most of the estimated overpressures increase toward the tips of the dikes and reach about 5 to 15 MPa (average was 8 MPa). In addition, results indicate host-rock fracture toughnesses between 60 MPa m1-2 and 170 MPa m1-2 (average 100 MPa m1-2). For comparison, we also estimated the magma overpressure by the least square method, assuming constant overpressure. This method gives overpressure between 1.5 MPa and 4 MPa (average 2.8 MPa). Similarly, the fracture toughnesses estimated in this way range between 30 MPa m1-2 and 120 MPa m1-2 (average 55 MPa m1-2). These methods and assumptions thus yield somewhat different results, as expected, but indicate the likely ranges of the magma overpressures and host-rock fracture toughnesses both of which are very reasonable and agree with earlier results obtained by different methods.

Publisher Correction: Hierarchical self-entangled carbon nanotube tube networks.

PubMed

Schütt, Fabian; Signetti, Stefano; Krüger, Helge; Röder, Sarah; Smazna, Daria; Kaps, Sören; Gorb, Stanislav N; Mishra, Yogendra Kumar; Pugno, Nicola M; Adelung, Rainer

2018-01-09

The original version of this Article was missing the ORCID ID of Professor Nicola Pugno.Also in the original version of this Article, the third to last sentence of the fourth paragraph of the Results incorrectly read 'However, the stepwise addition of CNTs increases the self-entanglement and thereby the compressive strength value as well as the Young's modulus (up to 2.5 MPa (normalized by density 6.4) and 24.5 MPa (normalized by density 62 MPa cm 3 g -1 ).' The correct version adds the units 'MPa cm 3 g -1 ' to '6.4'.Finally, in the original version of this Article, the y-axis label of Figure 3f incorrectly read 'Comp. strengthy'. The new version corrects that to 'Comp. Strength'.These errors have now been corrected in both the PDF and the HTML versions of the Article.

Combined effects of high pressure and sodium hydrogen carbonate treatment on beef: improvement of texture and color

NASA Astrophysics Data System (ADS)

Ohnuma, Shun; Kim, Yun-Jung; Suzuki, Atsushi; Nishiumi, Tadayuki

2013-06-01

We investigated the effect of combined high pressure and sodium hydrogen carbonate (NaHCO3) treatment on the physical properties and color of silverside Australian beef. Meat samples were pressurized at 100-500 MPa and the water content, weight reduction, rupture stress, and meat color were determined. The water content of meat treated with NaHCO3 and high pressure (300 MPa) reached a maximum of 70.1%. Weight reduction tended to decrease with high pressure treatment at 300 MPa. Meats treated with NaHCO3 and high pressure at 400 MPa showed a>50% decrease in hardness. Whitening of the meat was reduced by the combined high pressure and NaHCO3 treatment. Therefore, the combined high pressure and NaHCO3 treatment is effective for improvement of beef quality.

[Studies on technology of supercritical-CO2 fluid extraction for volatile oils and saikosaponins in Bupleurum chinense DC].

PubMed

Ge, F H; Li, Y; Xie, J M; Li, Q; Ma, G J; Chen, Y H; Lin, Y C; Li, X F

2000-03-01

To study the technology of supercritical-CO2 fluid extraction (SFE-CO2) for the volatile oils and saikosaponins in Bupleurum chinense. Exploring the effects of pressure, temperature, extraction time, flow rate of CO2 and entrainers on the yield of the oils and saikosaponin-contained extracts; determining the optimum conditions for SFE-CO2; analyzing the oils by GC/MS and comparing the technology of SFE-CO2 with that of traditional steam distillation. The optimum extraction conditions turned out to be--for volatile oils: pressure (EP) = 20 MPa, temperature (ET) = 30 degrees C, isolator I pressure (1P-I) = 12 MPa, temperature(1T-I) = 65 degrees C, isolator II pressure (1P-II) = 6 MPa, temperature (1T-II) = 40 degrees C, extraction time = 4 hours, and CO2 flow rate = 10-20 kg.(h.kg)-1 crude drug; for saikosaponins: EP = 30 MPa, ET = 65 degrees C, 1P I = 12 MPa, 1T I = 55 degrees C, 1P II = 6 MPa, 1T II = 43 degrees C, extraction time = 3 hours, entrainer = 60% ethanol, and CO2 flow rate = 20-25 kg.(h.kg)-1 crude drug. SFE-CO2 excels the traditional steam distillation in raising yield and reducing extraction time. The oils are composed of 22 constituents including caproaldehyde, and the saikosaponins can only be extracted with the help of entrainers under higher pressure and temperature.

[Changes of monocyte and monocyte-platelet aggregates in different subgroups of thrombotic events in patients with acute myocardial infarction during PCI].

PubMed

Wang, Sheng; Sun, Cuifang; Liao, Wang; Wu, Zhongwei; Wang, Yudai; Huang, Xiuxian; Lu, Sijia; Dong, Xiaoli; Shuai, Fujie; Li, Bin

2017-07-01

Objective To investigate the impact of thrombotic events on the alterations of monocyte and monocyte-platelet aggregates (MPAs) in patients with acute myocardial infarction (AMI) during percutaneous coronary intervention (PCI). Methods Blood was collected before PCI for flow cytometry. Monocyte subsets and MPAs were detected by four-color platform (CDl4-APC, CDl6-PE-Cy7, CD86-PE and CD41-Alexa Fluor R 488). According to the expression of the platelet surface marker CD41, the number of monocyte subsets and MPAs was analyzed using the fluorescent microspheres of absolute counting tube. The Wilcoxon rank sum test and receiver operating characteristic (ROC) curve analysis were performed. Results CD14 + CD16 ++ monocytes in intraprocedural thrombotic events (IPTE) group were significantly fewer than those in non-IPTE group, and the percentage in total mononuclear cells decreased. Compared with non-IPTE group, MPA binding ratio and monocyte subset MPA binding ratio were significantly higher in IPTE group. ROC analysis showed that MPA binding ratio and subgroup MPA binding ratio had a better predictive value for IPTE in patients with AMI. Conclusion The CD14 + CD16 ++ monocytes in IPTE group were significantly fewer than those in the non-IPTE group. MPA binding ratio and MPA binding ratio of monocyte subsets were significantly higher in the IPTE group than in the non-IPTE group, so they have a good predictive value for IPTE in patients with AMI.

High Pressure, Earth-storable Rocket Technology. Volume 1

NASA Technical Reports Server (NTRS)

Jassowski, D. M.

1997-01-01

The effect of elevated chamber pressure on combustion efficiency and heat transfer has been determined at the 100 lbf (445 N) thrust level for nitrogen tetroxide propellants. Measurements were made up to 500 psia (3.45 MPa) with testbed hardware; tests at 100 psia (0.690 MPa) and 250 psia (1.72 MPa) were made with radiation-cooled rhenium chambers. The first task of the program served to determine desirable thruster applications and operating conditions: high total impulse, i.e., communication satellite or spacecraft bus axial engines, at chamber pressures up to 250 psia (1.72 MPa) pressure-fed, or up to 500 psia (3.45 MPa) pump-fed. The hardware modifications and testing required to obtain the data were determined in Task 2, which included design-support hot fire tests; supplemental hardware, including a 250 psia (1.72 MPa) Pc rhenium chamber and a 20% fuel-film cooled platelet injector was fabricated in Task 3. Testing showed that satisfactory operation of Ir-Re radiation chambers is assured at pressures up to 250 psia and may be possible up to 500. The heat transfer data obtained show good correlation with throat Reynolds number and are generally under values given by the simplified Bartz equation; chambers equilibrium temperatures match predicted values. Preliminary optimization of trip configuration and mixture ratio were made; Isp performance from thrust measurements was within 1% of predicted values. Stability, compatibility, and front-end thermal management were determined to be satisfactory.

Construction strength analysis of landing craft tank conversion to passenger ship using finite element method

NASA Astrophysics Data System (ADS)

Nurul Misbah, Mohammad; Setyawan, Dony; Murti Dananjaya, Wisnu

2018-03-01

This research aims to determine the longitudinal strength of passenger ship which was converted from Landing Craft Tank with 54 m of length as stated by BKI (Biro Klasifikasi Indonesia / Indonesian Classification Bureau). Verification of strength value is done to 4 (four) loading conditions which are (1) empty load condition during sagging wave, (2) empty load condition during hogging wave, (3) full load condition during sagging wave and (4) full load condition during hogging wave. Analysis is done using Finite Element Analysis (FEA) software by modeling the entire part of passenger ship and its loading condition. The back and upfront part of ship centerline were used as the boundary condition. From that analysis it can be concluded that the maximum stress for load condition (1) is 72,393 MPa, 74,792 MPa for load condition (2), 129,92 MPa for load condition (3), and 132,4 MPa for load condition (4). Longitudinal strength of passenger ship fulfilled the criteria of empty load condition having smaller stress value than allowable stress which is 90 MPa, and during full load condition with smaller stress value than allowable stress which is 150 MPa. Analysis on longitudinal strength comparison with entire ship plate thickness variation of ± 2 mm from initial plate was also done during this research. From this research it can be concluded that plate thickness reduction causes the value of longitudinal strength to decrease, while plate thickness addition causes the value of longitudinal strength to increase.

Trace Detection of Organophosphorus Chemical Warfare Agents in Wastewater and Plants by Luminescent UIO-67(Hf) and Evaluating the Bioaccumulation of Organophosphorus Chemical Warfare Agents.

PubMed

Lian, Xiao; Yan, Bing

2018-05-02

Organophosphorus chemical warfare agents (OPCWAs) are a group of organic pollutants characterized by high toxicity and chemical stability, and they are very difficult to be degraded. The trace quality of OPCWAs in water and food will cause great harm to the human body. Therefore, the detection of OPCWAs is a difficult challenge, which has become the research hotspot over the world. In this work, a Hf-based luminescent metal-organic framework (Eu@1) is prepared, and the reactivity of Hf 12 results in a methanephosphonic acid (MPA)-induced luminescence quenching and the charge transfer from MPA to Hf(IV) and generated exciplexes which are responsible for this quenching effect. The excellent performance of Eu@1 in the detection of MPA, with its finer selectivity, high sensitivity (LOD = 0.4 ppm), and large linear range (10 -7 to 10 -3 M), is encouraging for application in wastewater detection. Importantly, MPA is a pollutant that can be absorbed by plants and causes the bioaccumulation effect, and thus, the detection of MPA in real plant samples is a purposeful topic. Eu@1 also achieved satisfactory results in actual plant sample testing, and the bioaccumulation of MPA in onions, turnips, and cabbages is determined via our sensor. This fabricated detector provides a feasible path for the detection of ppm-level OPCWAs in a complex environment, which will help humans to avoid OPCWA-contaminated foods.

Structural and mechanical implications of PMMA implant shape and interface geometry in cranioplasty--A finite element study.

PubMed

Ridwan-Pramana, Angela; Marcián, Petr; Borák, Libor; Narra, Nathaniel; Forouzanfar, Tim; Wolff, Jan

2016-01-01

This computational study investigates the effect of shape (defect contour curvature) and bone-implant interface (osteotomy angle) on the stress distribution within PMMA skull implants. Using finite element methodology, 15 configurations--combinations of simplified synthetic geometric shapes (circular, square, triangular, irregular) and interface angulations--were simulated under 50N static loads. Furthermore, the implant fixation devices were modelled and analysed in detail. Negative osteotomy configurations demonstrated the largest stresses in the implant (275 MPa), fixation devices (1258 MPa) and bone strains (0.04). The circular implant with zero and positive osteotomy performed well with maximum observed magnitudes of--implant stress (1.2 MPa and 1.2 MPa), fixation device stress (11.2 MPa and 2.2 MPa), bone strain (0.218e-3 and 0.750e-4). The results suggest that the preparation of defect sites is a critical procedure. Of the greatest importance is the angle at which the edges of the defect are sawed. If under an external load, the implant has no support from the interface and the stresses are transferred to the fixation devices. This can endanger their material integrity and lead to unphysiological strains in the adjacent bone, potentially compromising the bone morphology required for anchoring. These factors can ultimately weaken the stability of the entire implant assembly. Copyright © 2015 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

A review on therapeutic drug monitoring of immunosuppressant drugs.

PubMed

Mohammadpour, Niloufar; Elyasi, Sepideh; Vahdati, Naser; Mohammadpour, Amir Hooshang; Shamsara, Jamal

2011-11-01

: Immunosuppressants require therapeutic drug monitoring because of their narrow therapeutic index and significant inter-individual variability in blood concentrations. This variability can be because of factors like drug-nutrient interactions, drug-disease interactions, renal-insufficiency, inflammation and infection, gender, age, polymorphism and liver mass. Drug monitoring is widely practiced especially for cyclosporine, tacrolimus, sirolimus and mycophenolic acid. CYCLOSPORINE: Therapeutic monitoring of immunosuppressive therapy with cyclosporine is a critical requirement because of intra- and inter-patient variability of drug absorption, narrow therapeutic window and drug induced nephrotoxicity. MYCOPHENOLIC ACID MPA: Some reasons for therapeutic drug monitoring of MPA during post-transplant period include: relationship between MPA pharmacokinetic parameters and clinical outcomes, Inter-patient pharmacokinetic variability for MPA despite fixed MMF doses, alternations of MPA pharmacokinetics during the first months after transplantation, drug- drug interaction and influence of kidney function on MPA pharmacokinetic. SIROLIMUS: A recent review of the pharmacokinetics of sirolimus suggested a therapeutic range of 5 to 10 μg l(-1) in whole blood. However, the only consensus guidelines published on the therapeutic monitoring of sirolimus concluded that there was not enough information available about the clinical use of the drug to make recommendations. TACROLIMUS: Sudies have shown, in kidney and liver transplant patients, significant associations of low tacrolimus concentrations with rejection and of high concentrations with nephrotoxicity. Although the feasibility of a limited sampling scheme to predict AUC has been demonstrated, as yet, trough, or pre-dose, whole blood concentration monitoring is still the method of choice.

Effect of high-pressure homogenization on droplet size distribution and rheological properties of ice cream mixes.

PubMed

Innocente, N; Biasutti, M; Venir, E; Spaziani, M; Marchesini, G

2009-05-01

The effect of different homogenization pressures (15/3 MPa and 97/3 MPa) on fat globule size and distribution as well as on structure-property relationships of ice cream mixes was investigated. Dynamic light scattering, steady shear, and dynamic rheological analyses were performed on mixes with different fat contents (5 and 8%) and different aging times (4 and 20 h). The homogenization of ice cream mixes determined a change from bimodal to monomodal particle size distributions and a reduction in the mean particle diameter. Mean fat globule diameters were reduced at higher pressure, but the homogenization effect on size reduction was less marked with the highest fat content. The rheological behavior of mixes was influenced by both the dispersed and the continuous phases. Higher fat contents caused greater viscosity and dynamic moduli. The lower homogenization pressure (15/3 MPa) mainly affected the dispersed phase and resulted in a more pronounced viscosity reduction in the higher fat content mixes. High-pressure homogenization (97/3 MPa) greatly enhanced the viscoelastic properties and the apparent viscosity. Rheological results indicated that unhomogenized and 15/3 MPa homogenized mixes behaved as weak gels. The 97/3 MPa treatment led to stronger gels, perhaps as the overall result of a network rearrangement or interpenetrating network formation, and the fat globules were found to behave as interactive fillers. High-pressure homogenization determined the apparent viscosity of 5% fat to be comparable to that of 8% fat unhomogenized mix.

High Pressure, Earth-storable Rocket Technology. Volume 2

NASA Technical Reports Server (NTRS)

Jassowski, D. M.

1997-01-01

The effect of elevated chamber pressure on combustion efficiency and heat transfer has been determined at the 100 lbf (445 N) thrust level for nitrogen tetroxide propellants. Measurements were made up to 500 psia (3.45 Mpa) with testbed hardware; tests at 100 psia (0.690 MPa) and 250 psia (1.72 MPa) were made with radiation-cooled rhenium chambers. The first task of the program served to determine desirable thruster applications and operating conditions: high total impulse, i.e. communication satellite or spacecraft bus axial engines, at chamber pressures up to 250 psia (1.72 MPa) pressure-fed, or up to 500 psia (3.45 MPa) pump-fed. The hardware modifications and testing required to obtain the data were determined in Task 2, which included design-support hot fire tests; supplemental hardware, including a 250 psia (1.72 MPa) Pc rhenium chamber and a 20% fuel-film cooled platelet injector was fabricated in Task 3. Testing showed that satisfactory operation of Ir-Re radiation chambers is assured at pressures up to 250 psia and may be possible up to 500. The heat transfer data obtained show good correlation with throat Reynolds number and are generally under values given by the simplified Bartz equation; chambers equilibrium temperatures match predicted values. Preliminary optimization of trip configuration and mixture ratio were made; Isp performance from thrust measurements was within 1% of predicted values. Stability, compatibility, and front-end thermal management were determined to be satisfactory.

Bacterial spore inactivation at 45-65 °C using high pressure processing: study of Alicyclobacillus acidoterrestris in orange juice.

PubMed

Silva, Filipa V M; Tan, Eng Keat; Farid, Mohammed

2012-10-01

High pressure processing (HPP) is a new non-thermal technology commercially used to pasteurize fruit juices and extend shelf-life, while preserving delicate aromas/flavours and bioactive constituents. Given the spoilage incidents and economic losses due to Alicyclobacillus acidoterrestris in the fruit juice industry, the use of high pressure (200 MPa - 600 MPa) in combination with mild temperature (45 °C-65 °C) for 1-15 min, to inactivate these spores in orange juice were investigated. As expected, the higher the temperature, pressure and time, the larger was the A. acidoterrestris inactivation. The survival curves were described by the first order Bigelow model. For 200 MPa, D(45 °C) = 43.9 min, D(55 °C) = 28.8 min, D(65 °C) = 5.0 min and z-value = 21.3 °C. At 600 MPa, D(45 °C) = 12.9 min, D(55 °C) = 7.0 min, D(65 °C) = 3.4 min and z-value = 34.4 °C. Spores were inactivated at 45 °C and 600 MPa, and at 65 °C only 200 MPa was needed to achieve reduction in spore numbers. Results demonstrated that HPP allowed A. acidoterrestris spore inactivation at lower temperatures (45-65 °C) than conventional thermal processing (85-95 °C) without pressure, yielding a fresher and higher quality preserved food. Copyright © 2012 Elsevier Ltd. All rights reserved.

Effect of high pressure processing on dispersive and aggregative properties of almond milk.

PubMed

Dhakal, Santosh; Giusti, M Monica; Balasubramaniam, V M

2016-08-01

A study was conducted to investigate the impact of high pressure (450 and 600 MPa at 30 °C) and thermal (72, 85 and 99 °C at 0.1 MPa) treatments on dispersive and aggregative characteristics of almond milk. Experiments were conducted using a kinetic pressure testing unit and water bath. Particle size distribution, microstructure, UV absorption spectra, pH and color changes of processed and unprocessed samples were analyzed. Raw almond milk represented the mono model particle size distribution with average particle diameters of 2 to 3 µm. Thermal or pressure treatment of almond milk shifted the particle size distribution towards right and increased particle size by five- to six-fold. Micrographs confirmed that both the treatments increased particle size due to aggregation of macromolecules. Pressure treatment produced relatively more and larger aggregates than those produced by heat treated samples. The apparent aggregation rate constant for 450 MPa and 600 MPa processed samples were k450MPa,30°C  = 0.0058 s(-1) and k600MPa,30°C  = 0.0095 s(-1) respectively. This study showed that dispersive and aggregative properties of high pressure and heat-treated almond milk were different due to differences in protein denaturation, particles coagulation and aggregates morphological characteristics. Knowledge gained from the study will help food processors to formulate novel plant-based beverages treated with high pressure. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Short communication: Effects of high-pressure processing on the inactivity of Cronobacter sakazakii in whole milk and skim milk samples.

PubMed

Jiao, Rui; Gao, Jina; Li, Yinxiang; Zhang, Xiyan; Zhang, Maofeng; Ye, Yingwang; Wu, Qingping; Fan, Hongying

2016-10-01

Powdered infant formula is considered as the main transmission vehicle for Cronobacter sakazakii infections including meningitis, septicemia, and necrotizing enterocolitis. The effects of high-pressure processing treatment on inactivation of C. sakazakii ranging from 100 to 400 MPa for 3.0, 5.0, and 7.0 min in whole milk and skim milk were studied. Significant differences in inactivation of C. sakazakii were observed in milk samples under different pressures for 3 to 7 min compared with untreated samples, and C. sakazakii was not detected after 400 MPa for 3 min. The lethality rates of C. sakazakii cells in whole and skim milk with an initial level of 10(4) cfu/mL after 100 and 200 MPa treatments were not significantly different, but relatively higher lethality rates were found in whole milk after 300 MPa treatment than in skim milk. Finally, the scanning electron micrographs indicated that cellular envelope and intracellular damage of C. sakazakii cells were apparent after 300 and 400 MPa for 5.0 min compared with the untreated cells, and a progressive increase of injured cells with increased pressure treatment was found. It was concluded that C. sakazakii was sensitive to high-pressure processing treatment and that high-pressure processing treatment with 400 MPa for 3.0 min can be used to control C. sakazakii contamination in milk samples. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

High Pressure, Earth-Storable Rocket Technology. Volume 3; Appendices C and D

NASA Technical Reports Server (NTRS)

Jassowski, D. M.

1997-01-01

The effect of elevated chamber pressure on combustion efficiency and heat transfer has been determined at the 100 lbf (445 N) thrust level for nitrogen tetroxide propellants. Measurements were made up to 500 psia (3.45 MPa) with testbed hardware; tests at 100 psia (0.690 MPa) and 250 psia (1.72 MPa) were made with radiation-cooled rhenium chambers. The first task of the program served to determine desirable thruster applications and operating conditions: high total impulse, i.e. communication satellite or spacecraft bus axial engines, at chamber pressures up to 250 psia (1.72 MPa) pressure-fed, or up to 500 psia (3.45 MPa) pump-fed. The hardware modifications and testing required to obtain the data were determined in Task 2, which included design-support hot fire tests; supplemental hardware, including a 250 psia (1.72 MPa) Pc rhenium chamber and a 20% fuel-film cooled platelet injector was fabricated in Task 3. Testing showed that satisfactory operation of Ir-Re radiation chambers is assured at pressures up to 250 psia and may be possible up to 500. The heat transfer data obtained show good correlation with throat Reynolds number and are generally under values given by the simplified Bartz equation; chambers equilibrium temperatures match predicted values. Preliminary optimization of trip configuration and mixture ratio were made; Isp performance from thrust measurements was within 1% of predicted values. Stability, compatibility, and front-end thermal management were determined to be satisfactory.

Macrocystic ductal adenocarcinoma of prostate: A rare gross appearance of prostate cancer.

PubMed

Kojima, Fumiyoshi; Koike, Hiroyuki; Matsuzaki, Ibu; Iwahashi, Yoshifumi; Warigaya, Kenji; Fujimoto, Masakazu; Ono, Kazuo; Urata, Youji; Kohjimoto, Yasuo; Hara, Isao; Murata, Shin-Ichi

2017-04-01

Macroscopic cyst-formation by prostatic adenocarcinoma, herein referred to as macrocystic prostatic adenocarcinoma (MPA), is extremely rare. To date, no studies of prostate cancer performed based on gross cystic appearance have been reported. MPA can include various diseases, one of which is cystadenocarcinoma. Several cases of ductal adenocarcinoma exhibiting a macrocystic appearance have recently been reported; however, the histological and clinicopathological characteristics of MPAs have yet to be characterized and established. Therefore, we aimed to determine the histological and clinicopathological characteristics of MPA, via a multi-institutional investigation. We discovered five patients with MPA out of 1559 treated patients (0.32%); all cases were ductal adenocarcinomas. MPA was found to have three growth patterns: Two cases showed a prevalence of exuberant papillary proliferation with a fibrovascular core in the macroscopic multilocular cysts. Two others predominantly exhibited multilocular cysts lined by flat epithelium with foci of low papillae, and the fifth had a cystic lesion with intracancerous necrosis. Three of the cases showed extraprostatic invasion; however, none of the patients experienced recurrence during the follow-up period. Each predominant growth pattern tended to exhibit unique clinicopathological characteristics with respect to serum prostate specific antigen level and tumor size and location. In conclusion, we demonstrated that MPA is a ductal adenocarcinoma that is composed of intracystic exuberant papillary proliferation and flat proliferation with foci of low papillae, both of which might exhibit different clinicopathololgical appearances. Copyright © 2017 Elsevier Inc. All rights reserved.

Steps that count: physical activity recommendations, brisk walking, and steps per minute--how do they relate?

PubMed

Pillay, Julian D; Kolbe-Alexander, Tracy L; Proper, Karin I; van Mechelen, Willem; Lambert, Estelle V

2014-03-01

Brisk walking is recommended as a form of health-enhancing physical activity. This study determines the steps/minute rate corresponding to self-paced brisk walking (SPBW); a predicted steps/minute rate for moderate physical activity (MPA) and a comparison of the 2 findings. A convenience sample (N = 58: 34 men, 24 women, 31.7 ± 7.7 yrs), wearing pedometers and a heart rate (HR) monitor, performed SPBW for 10 minutes and 5 indoor sessions, regulated by a metronome (ranging from 60-120 steps/minute). Using steps/minute and HR data of the trials, a steps/minute rate for MPA was predicted. Adjustments were subsequently made for aerobic fitness (using maximal oxygen uptake (VO2max) estimates), age, and sex as possible contributors to stepping rate differences. Average steps/minute rate for SPBW was 118 ± 9 (116 ± 9; 121 ± 8 for men/women, respectively; P = .022); predicted steps/minute rate for MPA was 122 ± 37 (127 ± 36; 116 ± 39 for men/women, respectively; P < .99) and was similar to steps/minute rate of SPBW (P = .452), even after adjusting for age, sex, and aerobic fitness. Steps/minute rates of SPBW correlates closely with targeted HR for MPA, independent of aerobic fitness; predicted steps/minute rate for MPA relates closely to steps/minute rates of SPBW. Findings support current PA messages that use the term brisk walking as a reference for MPA.

Tritium, deuterium, and helium permeation through EPDM O-rings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Swansiger, W.A.

1992-03-01

This paper discusses tritium permeabilities determined at room temperature, 1.0 MPa (150 psia) tritium for three 23.4 cm diameter EPDM (ethylene-propylene-diene monomer) O-rings using a full-scale mock-up of the Al-SX shipping container seal geometry. The AL-SX container is being developed by Sandia National Laboratories for shipping tritium reservoirs. To determine the tritium permeation rate as a function of temperature, a 50.8 mm diameter EPDM O-ring was tested from room temperature to 150{degrees}C at a pressure of 1.0 MPa. Additional permeation measurements were made under the following test conditions: deuterium and helium-4 at room temperature and a pressure of 1.0 MPamore » using the full-scale AL-SX fixture, tritium from 0.1 MPa to 1.0 MPa at 142{degrees}C using the 50.8 mm fixture, and deuterium form room temperature to 150{degrees}C at a pressure of 1.0 MPa using the three full-scale O-rings showed the average room temperature, 1.0 MPa steady state tritium permeation rate to be about 1 {times} 10{sup {minus}2} Pa-liter/sec (7.6 {times} 10{sup {minus}5} torr-liter/sec or 1 {times} 10{sup {minus}4} std cc/sec), well within the allowable limit of 7.1 {times} 10{sup {minus}2} Pa-liter/sec for tritium release form the AL-SX container.« less

[Curing mode of universal adhesives affects the bond strength of resin cements to dentin].

PubMed

Fu, Z R; Tian, F C; Zhang, L; Han, B; Wang, X Y

2017-02-18

To determine the effects of curing mode of one-step and two-step universal adhesives on the micro-tensile bond strength (μTBS) of different dual-cure resin cements to dentin. One-step universal adhesive Single Bond Universal (SBU), and two-step universal adhesive OptiBond Versa (VSA) were chosen as the subjects, one-step self-etching adhesive OptiBond All in One (AIO) and two-step self-etching adhesive Clearfil SE Bond (SEB) were control groups, and two dual-cure resin cements RelyX Ultimate (RLX) and Nexus 3 Universal (NX3) were used in this study. In this study, 80 extracted human molars were selected and the dentin surface was exposed using diamond saw. The teeth were divided into 16 groups according to the adhesives (AIO, SBU, SEB, VSA), cure modes of adhesives (light cure, non-light cure) and resin cements (RLX, NX3). The adhesives were applied on the dentin surface following the instruction and whether light cured or not, then the resin cements were applied on the adhesives with 1 mm thickness and light cured (650 mW/cm(2) for 20 s. A resin was built up (5 mm) on the cements and light cured layer by layer. After water storage for 24 h, the specimens were cut into resin-cement-dentin strips with a cross sectional area of 1 mm×1 mm and the μTBS was measured. Regarding one-step universal adhesive (SBU) light cured, the μTBS with RLX [(35.45±7.04) MPa] or NX3 [(26.84±10.39) MPa] were higher than SBU non-light cured with RLX [(17.93±8.93) MPa)] or NX3 [(10.07±5.89) MPa, P<0.001]. Compared with AIO, light-cured SBU combined with RLX presented higher μTBS than AIO group [(35.45±7.04) MPa vs. (24.86±8.42) MPa, P<0.05]. When SBU was not lighted, the μTBS was lower than AIO [(17.93±8.93) MPa vs. (22.28±7.57) MPa, P<0.05]. For two-step universal adhesive (VSA) and control adhesive (SEB), curing mode did not affect the μTBS when used with either RLX or NX3 (25.98-32.24 MPa, P>0.05). Curing mode of one-step universal adhesive may affect the μTBS between dual-cure resin cements and dentin, while for two-step universal adhesive, the curing mode and the type of resin cements did not influence the μTBS.

Effects of fish movement assumptions on the design of a marine protected area to protect an overfished stock.

PubMed

Cornejo-Donoso, Jorge; Einarsson, Baldvin; Birnir, Bjorn; Gaines, Steven D

2017-01-01

Marine Protected Areas (MPA) are important management tools shown to protect marine organisms, restore biomass, and increase fisheries yields. While MPAs have been successful in meeting these goals for many relatively sedentary species, highly mobile organisms may get few benefits from this type of spatial protection due to their frequent movement outside the protected area. The use of a large MPA can compensate for extensive movement, but testing this empirically is challenging, as it requires both large areas and sufficient time series to draw conclusions. To overcome this limitation, MPA models have been used to identify designs and predict potential outcomes, but these simulations are highly sensitive to the assumptions describing the organism's movements. Due to recent improvements in computational simulations, it is now possible to include very complex movement assumptions in MPA models (e.g. Individual Based Model). These have renewed interest in MPA simulations, which implicitly assume that increasing the detail in fish movement overcomes the sensitivity to the movement assumptions. Nevertheless, a systematic comparison of the designs and outcomes obtained under different movement assumptions has not been done. In this paper, we use an individual based model, interconnected to population and fishing fleet models, to explore the value of increasing the detail of the movement assumptions using four scenarios of increasing behavioral complexity: a) random, diffusive movement, b) aggregations, c) aggregations that respond to environmental forcing (e.g. sea surface temperature), and d) aggregations that respond to environmental forcing and are transported by currents. We then compare these models to determine how the assumptions affect MPA design, and therefore the effective protection of the stocks. Our results show that the optimal MPA size to maximize fisheries benefits increases as movement complexity increases from ~10% for the diffusive assumption to ~30% when full environment forcing was used. We also found that in cases of limited understanding of the movement dynamics of a species, simplified assumptions can be used to provide a guide for the minimum MPA size needed to effectively protect the stock. However, using oversimplified assumptions can produce suboptimal designs and lead to a density underestimation of ca. 30%; therefore, the main value of detailed movement dynamics is to provide more reliable MPA design and predicted outcomes. Large MPAs can be effective in recovering overfished stocks, protect pelagic fish and provide significant increases in fisheries yields. Our models provide a means to empirically test this spatial management tool, which theoretical evidence consistently suggests as an effective alternative to managing highly mobile pelagic stocks.

Structural stability of methane hydrate at high pressures

USGS Publications Warehouse

Shu, J.; Chen, X.; Chou, I-Ming; Yang, W.; Hu, Jiawen; Hemley, R.J.; Mao, Ho-kwang

2011-01-01

The structural stability of methane hydrate under pressure at room temperature was examined by both in-situ single-crystal and powder X-ray diffraction techniques on samples with structure types I, II, and H in diamond-anvil cells. The diffraction data for types II (sII) and H (sH) were refined to the known structures with space groups Fd3m and P63/mmc, respectively. Upon compression, sI methane hydrate transforms to the sII phase at 120 MPa, and then to the sH phase at 600 MPa. The sII methane hydrate was found to coexist locally with sI phase up to 500 MPa and with sH phase up to 600 MPa. The pure sH structure was found to be stable between 600 and 900 MPa. Methane hydrate decomposes at pressures above 3 GPa to form methane with the orientationally disordered Fm3m structure and ice VII (Pn3m). The results highlight the role of guest (CH4)-host (H2O) interactions in the stabilization of the hydrate structures under pressure.

The shear fracture toughness, KIIc, of graphite

DOE PAGES

Burchell, Timothy D.; Erdman, III, Donald L.

2015-11-05

In this study, the critical shear stress intensity factor, KIIc, here-in referred to as the shear fracture toughness, KIIc (MPa m), of two grades of graphite are reported. The range of specimen volumes was selected to elucidate any specimen size effect, but smaller volume specimen tests were largely unsuccessful, shear failure did not occur between the notches as expected. This was probably due to the specimen geometry causing the shear fracture stress to exceed the compressive failure stress. In subsequent testing the specimen geometry was altered to reduce the compressive footprint and the notches (slits) made deeper to reduce themore » specimen's ligament length. Additionally, we added the collection of Acoustic Emission (AE) during testing to assist with the identification of the shear fracture load. The means of KIIc from large specimens for PCEA and NBG-18 are 2.26 MPa m with an SD of 0.37 MPa m and 2.20 MPa m with an SD of 0.53 MPa m, respectively. The value of KIIc for both graphite grades was similar, although the scatter was large. In this work we found the ratio of KIIc/ KIc ≈ 1.6. .« less

Effects of different heat-moisture treatments on the physicochemical properties of brown rice flour.

PubMed

Nakamura, Sumiko; Okumura, Hisako; Sugawara, Masayoshi; Noro, Wataru; Homma, Noriyuki; Ohtsubo, Ken'ichi

2017-12-01

We evaluated the effect of heat-moisture treatment (HMT) on the main chemical components, physical properties, and enzyme activities of two types of brown rice flour: high-amylose Koshinokaori and normal-quality Koshiibuki. Five different HMTs using brown rice (moisture content was 12.0%) were assessed: 0.1 MPa/120 °C for 5 or 10 min, 0.2 MPa/134 °C for 5 or 10 min and 0.3 MPa/144 °C for 10 min. HMT, decreased the α-amylase and lipase activities, and fat acidity, and slightly increased the dietary fiber and resistant starch levels. After 2 months' storage at 35 °C, rice samples that were treated with 0.2 MPa/134 °C or 0.3 MPa/144 °C for 10 min had a lower fat acidity than untreated samples, which would be useful for long-term storage and export of rice flour. And HMT exhibited inhibition of retrogradation in the pasting and physical properties, which is profitable to promote the qualities of the rice products.

High pressure processing alters water distribution enabling the production of reduced-fat and reduced-salt pork sausages.

PubMed

Yang, Huijuan; Han, Minyi; Bai, Yun; Han, Yanqing; Xu, Xinglian; Zhou, Guanghong

2015-04-01

High pressure processing (HPP) was used to explore novel methods for modifying the textural properties of pork sausages with reduced-salt, reduced-fat and no fat replacement additions. A 2×7 factorial design was set up, incorporating two pressure levels (0.1 or 200 MPa) and seven fat levels (0, 5, 10, 15, 20, 25 and 30%). Sausages treated at 200 MPa exhibited improved tenderness at all fat levels compared with 0.1 MPa treated samples, and the shear force of sausages treated at 200 MPa with 15 or 20% fat content was similar to the 0.1 MPa treated sausages with 30% fat. HPP significantly changed the P₂ peak ratio of the four water components in raw sausages, resulting in improved textural properties of emulsion-type sausages with reduced-fat and reduced-salt. Significant correlations were found between pH, color, shear force and water proportions. The scanning and transmission micrographs revealed the formation of smaller fat globules and an improved network structure in the pressure treated sausages. In conclusion, there is potential to manufacture sausages with reduced-fat and reduced-salt by using HPP to maintain textural qualities. Copyright © 2014. Published by Elsevier Ltd.

Extension of the shelf life of prawns (Penaeus japonicus) by vacuum packaging and high-pressure treatment.

PubMed

López-Caballero, M E; Pérez-Mateos, M; Borderías, J A; Montero, P

2000-10-01

The present study has investigated the application of high pressures (200 and 400 MPa) in chilled prawn tails, both conventionally stored (air) and vacuum packaged. Vacuum packaging and high-pressure treatment did extend the shelf life of the prawn samples, although it did affect muscle color very slightly, giving it a whiter appearance. The viable shelf life of 1 week for the air-stored samples was extended to 21 days in the vacuum-packed samples, 28 days in the samples treated at 200 MPa, and 35 days in the samples pressurized at 400 MPa. Vacuum packaging checked the onset of blackening, whereas high-pressure treatment aggravated the problem. From a microbiological point of view, batches conventionally stored reached about 6 log CFU/g or even higher at 14 days. Similar figures were reached in total number of bacteria in vacuum-packed samples and in pressurized at 200-MPa samples at 21 days. When samples were pressurized at 400 MPa, total numbers of bacteria were below 5.5 log CFU/g at 35 days of storage. Consequently, a combination of vacuum packaging and high-pressure treatment would appear to be beneficial in prolonging freshness and preventing spotting.

High-pressure protein crystallography of hen egg-white lysozyme

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamada, Hiroyuki; Nagae, Takayuki; Watanabe, Nobuhisa, E-mail: nobuhisa@nagoya-u.jp

The crystal structure of hen egg-white lysozyme (HEWL) was analyzed under pressures of up to 950 MPa. The high pressure modified the conformation of the molecule and induced a novel phase transition in the tetragonal crystal of HEWL. Crystal structures of hen egg-white lysozyme (HEWL) determined under pressures ranging from ambient pressure to 950 MPa are presented. From 0.1 to 710 MPa, the molecular and internal cavity volumes are monotonically compressed. However, from 710 to 890 MPa the internal cavity volume remains almost constant. Moreover, as the pressure increases to 950 MPa, the tetragonal crystal of HEWL undergoes a phasemore » transition from P4{sub 3}2{sub 1}2 to P4{sub 3}. Under high pressure, the crystal structure of the enzyme undergoes several local and global changes accompanied by changes in hydration structure. For example, water molecules penetrate into an internal cavity neighbouring the active site and induce an alternate conformation of one of the catalytic residues, Glu35. These phenomena have not been detected by conventional X-ray crystal structure analysis and might play an important role in the catalytic activity of HEWL.« less

Impacts of marine protected areas on fishing communities.

PubMed

Mascia, Michael B; Claus, C Anne; Naidoo, Robin

2010-10-01

Marine protected areas (MPAs) are a popular conservation strategy, but their impacts on human welfare are poorly understood. To inform future research and policy decisions, we reviewed the scientific literature to assess MPA impacts on five indicators of human welfare: food security, resource rights, employment, community organization, and income. Following MPA establishment, food security generally remained stable or increased in older and smaller MPAs. The ability of most fishing groups to govern MPA resources changed. Increased resource rights were positively correlated with MPA zoning and compliance with MPA regulations. Small sample sizes precluded statistical tests of the impacts of MPAs on employment, community organization, and income. Our results demonstrate that MPAs shape the social well-being and political power of fishing communities; impacts (positive and negative) vary within and among social groups; and social impacts are correlated with some--but not all--commonly hypothesized explanatory factors. Accordingly, MPAs may represent a viable strategy for enhancing food security and empowering local communities, but current practices negatively affect at least a minority of fishers. To inform policy making, further research must better document and explain variation in the positive and negative social impacts of MPAs. © 2010 Society for Conservation Biology.

Testing of polyimide second-stage rod seals for single-state applications in advanced aircraft hydraulic systems

NASA Technical Reports Server (NTRS)

Waterman, A. W.

1977-01-01

Machined polyimide second-stage rod seals were evaluated to determine their suitability for single-stage applications where full system pressure acts on the upstream side of the seal. The 6.35-cm (2.5-in.) K-section seal was tested in impulse screening tests where peak pressure was increased in 3.448-MPa (500-psi) increments each 20,000 cycles. Seal failure occurred at 37.92 MPa (5,500 psi), indicating a potential for acceptability in a 27.58-MPa (4,000-psi) system. Static pressurization for 600 sec at pressures in excess of 10.34 MPa (1,500 psi) revealed structural inadequacy of the seal cross section to resist fracture and extrusion. Endurance testing showed the seals capable of at least 65,000 1.27-cm (0.5-in.) cycles at 450 K (350 F) without leakage. It was concluded that the second-stage seals were proven to be exceptional in the 1.379-MPa (200-psi) applications for which they were designed, but polyimide material properties are not adequate for use in this design at pressure loading equivalent to that present in single-stage applications.

A fast tumor-targeting near-infrared fluorescent probe based on bombesin analog for in vivo tumor imaging.

PubMed

Chen, Haiyan; Wan, Shunan; Zhu, Fenxia; Wang, Chuan; Cui, Sisi; Du, Changli; Ma, Yuxiang; Gu, Yueqing

2014-01-01

Bombesin (BBN), an analog of gastrin-releasing peptide (GRP), of which the receptors are over-expressed on various tumor cells, is able to bind to GRP receptor specifically. In this study, a near-infrared fluorescent dye (MPA) and polyethylene glycol (PEG) were conjugated to BBN analog to form BBN[7-14]-MPA and BBN[7-14]-SA-PEG-MPA. The successful synthesis of the two probes was proved by the characterization via sodium dodecylsulfate-polyacrylamide gel electrophoresis, infrared and optical spectra. Cellular uptakes studies indicated that BBN-based probes were mediated by gastrin-releasing peptide receptors (GRPR) on tumor cells and the PEG modified probe had higher affinity. The dynamic distribution and clearance investigations showed that the BBN-based probes were eliminated by the liver-kidney pathway. Furthermore, both of the BBN-based probes displayed tumor-targeting ability in GRPR over-expressed tumor-bearing mice. The PEG modified probe exhibited faster and higher tumor targeting capability than BBN[7-14]-MPA. The results implied that BBN[7-14]-SA-PEG-MPA could act as an effective fluorescence probe for tumor imaging. Copyright © 2014 John Wiley & Sons, Ltd.

Improving LED CCT uniformity using micropatterned films optimized by combining ray tracing and FDTD methods.

PubMed

Ding, Xinrui; Li, Jiasheng; Chen, Qiu; Tang, Yong; Li, Zongtao; Yu, Binhai

2015-02-09

Although the light-emitting diode (LED) has revolutionized lighting, the non-uniformity of its correlated color temperature (CCT) still remains a major concern. In this context, to improve the light distribution performance of remote phosphor LED lamps, we employ a micropatterned array (MPA) optical film fabricated using a low-cost molding process. The parameters of the MPA, including different installation configurations, positioning, and diameters, are optimized by combining the finite-difference time-domain and ray-tracing methods. Results show that the sample with the upward-facing convex-cone MPA film that has a diameter of half of that of the remote phosphor glass, and is tightly affixed to the inward surface of the remote phosphor glass renders a superior light distribution performance. When compared with the case in which no MPA film is used, the deviation of the CCT distribution decreases from 1033 K to 223 K, and the corresponding output power of the sample is an acceptable level of 85.6%. We perform experiments to verify our simulation results, and the two sets of results exhibit a close agreement. We believe that our approach can be used to optimize MPA films for various lighting applications.

[High-dosed gestagen therapy of the metastatic mammary carcinoma (author's transl)].

PubMed

Firusian, N; Becher, R

1981-12-01

Thirty patients with histologically proven metastatic mammary carcinoma were treated, after exhaustion of hormonal and cytostatic therapeutic means, with high-dosed medroxyprogesterone acetate (MPA) during a ten-day induction phase with 1000 mg MPAi.m. per day and then with 600 mg oral MPA per day. In eleven patients a complete or partial remission was achieved. The median period of remission comprised ten months. A positive relationship was found between the response to high-dosed MPA therapy and the length of free intervals. Side effects were tolerable.

A new high strength alloy for hydrogen fueled propulsion systems

NASA Technical Reports Server (NTRS)

Mcpherson, W. B.

1986-01-01

This paper describes the development of a high-strength alloy (1241 MPa ultimate and 1103 MPa yield, with little or no degradation in hydrogen) for application in advanced hydrogen-fueled rocket engines. Various compositions of the Fe-Ni-Co-Cr system with elemental additions of Cb, Ti and Al are discussed. After processing, notched tensile specimens were tested in 34.5-MPa hydrogen at room temperature, as the main screening test. The H2/air notch tensile ratio was used as the selection/rejection criterion. The most promising alloys are discussed.

The effect of stress on limestone permeability and its effective stress behavior

NASA Astrophysics Data System (ADS)

Meng, F.; Baud, P.; Ge, H.; Wong, T. F.

2017-12-01

The evolution of permeability and its effective stress behavior is related to inelastic deformation and failure mode. This was investigated in Indiana and Purbeck limestones with porosities of 18% and 13%, respectively. Hydrostatic and triaxial compression tests were conducted at room temperature on water-saturated samples at pore pressure of 5 MPa and confining pressures up to 90 MPa. Permeability was measured using steady flow at different stages of deformation. For Indiana limestone, under hydrostatic loading pore collapse initiated at critical pressure P* 55 MPa with an accelerated reduction of permeability by 1/2. At a confinement of 35 MPa and above, shear-enhanced compaction initiated at critical stress C*, beyond which permeability reduction up to a factor of 3 was observed. At a confinement of 15 MPa and below, dilatancy initiated at critical stress C', beyond which permeability continued to decrease, with a negative correlation between porosity and permeability changes. Purbeck limestone showed similar evolution of permeability. Microstructural and mercury porosimetry data showed that pore size distribution in both Indiana and Purbeck limestones is bimodal, with significant proportions of macropores and micropores. The effective stress behaviour of a limestone with dual porosity is different from the prediction for a microscopically homogeneous assemblage, in that its effective stress coefficients for permeability and porosity change may attain values significantly >1. Indeed this was confirmed by our measurements (at confining pressures of 7-15 MPa and pore pressures of 1-3 MPa) in samples that had not been deformed inelastically. We also investigated the behavior in samples hydrostatically and triaxially compacted to beyond the critical stresses P* and C*, respectively. Experimental data for these samples consistently showed effective stress coefficients for both permeability and porosity change with values <1. Thus the effective stress behavior in an inelastically compacted sample is fundamentally different, with attributes akin to that of a microscopically homogeneous assemblage. This is likely related to compaction from pervasive collapse of macropores, which would effectively homogenize the initially bimodal pore size distribution.

KEY COMPARISON: Final report on Key Comparison APMP.SIM.M.P-K1c: Bilateral comparison between NIST (USA) and NPLI (India) in the pneumatic pressure region 0.4 MPa to 4.0 MPa

NASA Astrophysics Data System (ADS)

Driver, R. Gregory; Olson, Douglas A.; Dilawar, Nita; Bandyopadhyay, A. K.

2007-01-01

We report the results of a bilateral comparison of pressure measurement between NIST and NPLI using a piston gauge transfer standard (TS), designated as NPLI-4, over the range of nominal applied pressure 0.4 MPa to 4.0 MPa. This TS was cross-floated against the laboratory secondary standard designated as PG13 at NIST, USA and against NPLI-8 at NPLI, India. The nominal pressure points of the bilateral comparison were (0.4, 0.8, 1.2, 1.6, 2.0, 2.4, 2.8, 3.2, 3.6 and 4.0) MPa, respectively. The comparison was performed in both the institutes in identical pressure cycles in increasing pressures. The comparison data were analysed in terms of the effective area [Ap (mm2)] as a function pressure [p (MPa)] of the TS at the above-mentioned pressures. We have also estimated the zero-pressure effective area [A0 (mm2)] and the pressure distortion coefficient [λ (MPa-1)] of the transfer standard. The consistency of the results at every pressure in the range indicates that the laboratory standards used in this comparison are compatible, uniform and can be considered traceable to each other. Finally, the degree of equivalence between NPLI and NIST is 11.4 × 10-6 or better, which is always less than the relative standard uncertainty of the difference (33.6 × 10-6). Main text. To reach the main text of this Paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (MRA).

Fixed versus Removable Appliance for Palatal Expansion; A 3D Analysis Using the Finite Element Method

PubMed Central

Geramy, Allahyar; Shahroudi, Atefe Saffar

2014-01-01

Objective: Several appliances have been used for palatal expansion for treatment of posterior cross bite. The purpose of this study was to evaluate the stress induced in the apical and crestal alveolar bone and the pattern of tooth displacement following expansion via removable expansion plates or fixed-banded palatal expander using the finite element method (FEM) analysis. Materials and Methods: Two 3D FEM models were designed from a mesio-distal slice of the maxilla containing the upper first molars, their periodontium and alveolar bone. Two palatal expanders (removable and fixed) were modeled. The models were designed in SolidWorks 2006 and then transferred to ANSYS Workbench. The appliance halves were displaced 0.1 mm laterally. The von Mises stress in the apical, crestal, and PDL areas and also the vertical displacement of the cusps (palatal and buccal) was were evaluated. Results: The total PDL stress was 0.40003 MPa in the removable appliance (RA) model and 4.88e-2 MPa in the fixed appliance (FA) model and the apical stress was 9.9e-2 and 1.17e-2 MPa, respectively. The crestal stress was 2.99e-1 MPa in RA and 7.62e-2 MPa in the FA. The stress in the cortical bone crest was 0.30327 and 7.9244e-2 MPa for RA and FA, respectively and 3.7271 and 7.4373e-2 MPa in crestal area of spongy bone, respectively. The vertical displacement of the buccal cusp and palatal cusp was 1.64e-2 and 5.90e-2 mm in RA and 1.05e-4 and 1.7e-4 mm in FA, respectively. Conclusion: The overall stress as well as apical and crestal stress in periodontium of anchor teeth was higher in RA than FA; RA elicited higher stress in both cortical and spongy bone. The vertical displacement of molar cusps was more in removable than fixed palatal expander model. PMID:24910679

Frequency-Dependent Evaluation of the Role of Definity in Producing Sonoporation of Chinese Hamster Ovary Cells

PubMed Central

Forbes, Monica M.; Steinberg, Ryan L.; O'Brien, William D.

2011-01-01

Objectives Sonoporation uses ultrasound (US) and ultrasound contrast agents (UCAs) to enhance cell permeabilization, thereby allowing delivery of therapeutic compounds non-invasively into specific target cells. The objective of this study was to elucidate the biophysical mechanism of sonoporation, specifically the role of UCAs as well as exposure frequency. The inertial cavitation (IC) thresholds of the lipid-shelled octafluoropropane UCA were directly compared to the levels of generated sonoporation to determine the involvement of UCAs in producing sonoporation. Methods Chinese hamster ovary cells were exposed as a monolayer in a solution of the UCA, 500,000-Da fluorescein isothiocyanate-dextran, and phosphate-buffered saline to 30 seconds of pulsed US (pulse duration, 5 cycles; pulse repetition frequency, 10 Hz) at 3 frequencies (0.92, 3.2, and 5.6 MHz). The peak rarefactional pressure (Pr) was varied over a range from 4 kPa to 4.1 MPa, and 5 to 7 independent replicates were performed at each pressure. Results The experimental observations demonstrated that IC was likely not the physical mechanism for sonoporation. Sonoporation activity was observed at pressure levels below the threshold for IC of the UCA (1.27 ± 0.32 MPa at 0.92 MHz, 0.84 ± 0.19 MPa at 3.2 MHz, and 2.57 ± 0.26 MPa at 5.6 MHz) for all 3 frequencies examined. The Pr values at which the peak sonoporation activity occurred were 1.4 MPa at 0.92 MHz, 0.25 MPa at 3.2 MHz, and 2.3 MPa at 5.6 MHz. The UCA collapse thresholds followed a similar trend. A 1-way analysis of variance test confirmed that sonoporation activity differed among the 3 frequencies examined (P = 10−8). Conclusions These results thus suggest that sonoporation is related to linear and/or nonlinear oscillation of the UCA occurring at pressure levels below the IC threshold. PMID:21193706

Determination of the mitigating effect of colon-specific bioreversible codrugs of mycophenolic acid and aminosugars in an experimental colitis model in Wistar rats

PubMed Central

Chopade, Shakuntala Santosh; Dhaneshwar, Suneela Sunil

2018-01-01

AIM To design colon-targeted codrugs of mycophenolic acid (MPA) and aminosugars as a safer option to mycophenolate mofetil (MMF) in the management of inflammatory bowel disease. METHODS Codrugs were synthesized by coupling MPA with aminosugars (D-glucosamine and D-galactosamine) using EDCI coupling. The structures were confirmed by infrared radiation, nuclear magnetic resonance, mass spectroscopy and elemental analysis. The release profile of codrugs was extensively studied in aqueous buffers, upper gastrointestinal homogenates, faecal matter and caecal homogenates (in vitro) and rat blood (in vitro). Anti-colitic activity was assessed in 2,4,6-trinitrobezenesulfonic acid-induced colitis in Wistar rats by the estimation of various demarcating parameters. Statistical evaluation was performed by applying one-way and two-way ANOVA when compared with the disease control. RESULTS The prodrugs resisted activation in HCl buffer (pH 1.2) and stomach homogenates of rats with negligible hydrolysis in phosphate buffer (pH 7.4) and intestinal homogenates. Incubation with colon homogenates (in vitro) produced 76% to 89% release of MPA emphasizing colon-specific activation of codrugs and the release of MPA and aminosugars at the site of action. In the in vitro studies, the prodrug of MPA with D-glucosamine (MGLS) was selected which resulted in 68% release of MPA in blood. in vitro studies on MGLS revealed its colon-specific activation after a lag time of 8 h which could be ascribed to the hydrolytic action of N-acyl amidases found in the colon. The synthesized codrugs markedly diminished disease activity score and revived the disrupted architecture of the colon that was comparable to MMF but superior to MPA. CONCLUSION The significant attenuating effect of prodrugs and individual aminosugars on colonic inflammation proved that the rationale of the codrug approach is valid. PMID:29563754

Experimental Study of Hybrid Fractures and the Transition From Joints to Faults

NASA Astrophysics Data System (ADS)

Ramsey, J. M.; Chester, F. M.

2003-12-01

Joints and faults are end members of a continuous spectrum of brittle fractures including the hybrid fractures, hypothesized to form under mixed compressive and tensile stress. However, unequivocal evidence for the existence of hybrid fractures has not been presented. To investigate this transition, we have conducted triaxial extension experiments on dog-bone shaped cylindrical samples of Carrara marble at room temperature, an axial extension rate of 2x10-2 mm s-1, and confining pressures between 7.5 and 170 MPa. Two parallel suites of experiments were completed, one using very weak, latex jacketing to obtain accurate failure strength, and another using copper foil jacketing to preserve fracture surfaces. The combined data set provides strong evidence for the existence of hybrid fractures on the basis of the progressive change in failure strength, fracture orientation, and fracture surface morphology from joints to faults. At the lowest confining pressures (7.5 to 60 MPa), fractures are oriented approximately parallel to the maximum principal compressive stress, form at a tensile axial stress of approximately -7.75 MPa (i.e. the uniaxial tensile strength), and display fracture surfaces characterized by many reflective grain-scale cleavage faces, consistent with jointing. At the highest confining pressures (130 to 170 MPa), fractures are oriented from 13.4 to 21.6 degrees to the maximum principal compressive stress, form under completely compressive stress states where the axial stress is between 0 and 4.3 MPa, and are characterized by short slip lineations and powdery, finely comminuted grains consistent with faulting. At intermediate confining pressures (70 to 120 MPa), fractures are oriented from 3.7 to 12.4 degrees to the maximum principal compressive stress, form under mixed stress conditions with the axial stress ranging from -10.6 to -3.0 MPa, and display both reflective cleavage faces and short slip lineations with comminuted grains, consistent with hybrid fracturing.

Assessing Dispersal Patterns of Fish Propagules from an Effective Mediterranean Marine Protected Area

PubMed Central

Di Franco, Antonio; Coppini, Giovanni; Pujolar, José Martin; De Leo, Giulio A.; Gatto, Marino; Lyubartsev, Vladyslav; Melià, Paco; Zane, Lorenzo; Guidetti, Paolo

2012-01-01

Successfully enforced marine protected areas (MPAs) have been widely demonstrated to allow, within their boundaries, the recovery of exploited species and beyond their boundaries, the spillover of juvenile and adult fish. Little evidence is available about the so-called ‘recruitment subsidy’, the augmented production of propagules (i.e. eggs and larvae) due to the increased abundance of large-sized spawners hosted within effective MPAs. Once emitted, propagules can be locally retained and/or exported elsewhere. Patterns of propagule retention and/or export from MPAs have been little investigated, especially in the Mediterranean. This study investigated the potential for propagule production and retention/export from a Mediterranean MPA (Torre Guaceto, SW Adriatic Sea) using the white sea bream, Diplodus sargus sargus, as a model species. A multidisciplinary approach was used combining 1) spatial distribution patterns of individuals (post-settlers and adults) assessed through visual census within Torre Guaceto MPA and in northern and southern unprotected areas, 2) Lagrangian simulations of dispersal based on an oceanographic model of the region and data on early life-history traits of the species (spawning date, pelagic larval duration) and 3) a preliminary genetic study using microsatellite loci. Results show that the MPA hosts higher densities of larger-sized spawners than outside areas, potentially guaranteeing higher propagule production. Model simulations and field observation suggest that larval retention within and long-distance dispersal across MPA boundaries allow the replenishment of the MPA and of exploited populations up to 100 km down-current (southward) from the MPA. This pattern partially agrees with the high genetic homogeneity found in the entire study area (no differences in genetic composition and diversity indices), suggesting a high gene flow. By contributing to a better understanding of propagule dispersal patterns, these findings provide crucial information for the design of MPAs and MPA networks effective to replenish fish stocks and enhance fisheries in unprotected areas. PMID:23284887

Isolation and characterization of a CO2-tolerant Lactobacillus strain from Crystal Geyser, Utah, U.S.A.

NASA Astrophysics Data System (ADS)

Santillan, Eugenio Felipe; Shanahan, Timothy; Omelon, Christopher; Major, Jonathan; Bennett, Philip

2015-07-01

When CO2 is sequestered into the deep subsurface, changes to the subsurface microbial community will occur. Capnophiles, microorganisms that grow in CO2-rich environments, are some organisms that may be selected for under the new environmental conditions. To determine whether capnophiles comprise an important part of CO2-rich environments, an isolate from Crystal Geyser, Utah, U.S.A., a CO2- rich spring considered a carbon sequestration analogue, was characterized. The isolate was cultured under varying CO2, pH, salinity, and temperature, as well as different carbon substrates and terminal electron acceptors (TEAs) to elucidate growth conditions and metabolic activity. Designated CG-1, the isolate is related (99%) to Lactobacillus casei in 16S rRNA gene identity, growing at PCO2 between 0 to 1.0 MPa. Growth is inhibited at 2.5 MPa, but stationary phase cultures exposed to this pressure survive beyond 5 days. At 5.0 MPa, survival is at least 24 hours. CG-1 grows in neutral pH, 0.25 M NaCl, and between 25° to 45°C andconsumes glucose, lactose, sucrose, or crude oil, likely performing lactic acid fermentation. Fatty acid profiles between 0.1 MPa to 1.0 MPa suggests decreases in cell size and increases in membrane rigidity. Transmission electron microscopy reveals rod shaped bacteria at 0.1 MPa. At 1.0 MPa, cells are smaller, amorphous, and produce abundant capsular material. Its ability to grow in environments regardless of the presence of CO2 suggests we have isolated an organism that is more capnotolerant than capnophilic. Results also show that microorganisms are capable of surviving the stressful conditions created by the introduction of CO2 for sequestration. Furthermore, our ability to culture an environmental isolate indicates that organisms found in CO2 environments from previous genomic and metagenomics studies are viable, metabolizing, and potentially affecting the surrounding environment.

Repair of heat damaged reinforced concrete slab with High Strength Fibre Reinforced Concrete materials

NASA Astrophysics Data System (ADS)

Ain Hamiruddin, Nur; Razak, Rafiza Abd; Muhammad, Khairunnisa; Zahid, Muhd Zulham Affendi Mohd

2018-04-01

The purpose of this study is to investigate the flexural behaviour of heat damaged reinforced concrete (RC) slab by using High Strength Fibre Reinforced Concrete (HSFRC) as repair materials. The slab samples consist of twelve one-way columns heated at 200 ° C, 400 ° C and 600 ° C for 120 minutes. The thickness of the HSFRC layer used to heat damaged slab samples is 40 mm thick. Two distinct curing methods were implement during this study: i.e. normal curing (standard room temperature 26°C) and heat curing (temperature of 90°C for 48 hours). The center-point loading flexural strength test based on ASTM C 293 were referred to examine the flexural strength of the slab samples other than evaluated the mechanical properties of repaired samples (i.e. flexural strength, secant stiffness, toughness and ductility). The HSFRC's results showed that compressive strength at 28 days was 88.66 MPa. Whereas the flexural strength of heat damage repaired samples that exposed to 200°C (R200), 400°C (RNC400) and 400°C (RHC400) were gained by about 3.06% (34.93 MPa), 14.47% (38.79 MPa) and 30.95% (44.38 MPa) respectively, contrasted to the control sample (CS) which is 33.89 MPa. However, heat damage for non-repaired samples that exposed to 200 ° C (NR200) and 400°C (NR400) decline by about 0.77% (33.63 MPa) and 8.13% (31.14 MPa) respectively. Therefore, the utilized of HSFRC as repair materials can improve the flexural strength than control sample (CS). This is clearly indicate that HSFRC can enhance the mechanical properties of heat damaged reinforced concrete (RC) slab which can illustrate that the results of flexural behaviour reflected the superiority by using HSFRC as repair materials.

High-pressure-induced water penetration into 3-­isopropylmalate dehydrogenase

PubMed Central

Nagae, Takayuki; Kawamura, Takashi; Chavas, Leonard M. G.; Niwa, Ken; Hasegawa, Masashi; Kato, Chiaki; Watanabe, Nobuhisa

2012-01-01

Hydrostatic pressure induces structural changes in proteins, including denaturation, the mechanism of which has been attributed to water penetration into the protein interior. In this study, structures of 3-isopropylmalate dehydrogenase (IPMDH) from Shewanella oneidensis MR-1 were determined at about 2 Å resolution under pressures ranging from 0.1 to 650 MPa using a diamond anvil cell (DAC). Although most of the protein cavities are monotonically compressed as the pressure increases, the volume of one particular cavity at the dimer interface increases at pressures over 340 MPa. In parallel with this volume increase, water penetration into the cavity could be observed at pressures over 410 MPa. In addition, the generation of a new cleft on the molecular surface accompanied by water penetration could also be observed at pressures over 580 MPa. These water-penetration phenomena are considered to be initial steps in the pressure-denaturation process of IPMDH. PMID:22349232

Indentation Creep Behavior of Nugget Zone of Friction Stir Welded 2014 Aluminum Alloy

NASA Astrophysics Data System (ADS)

Das, Jayashree; Robi, P. S.; Sankar, M. Ravi

2018-04-01

The present study is aimed at evaluating the creep behavior of the nugget zone of friction welded 2014 Aluminum alloy by indentation creep tests. Impression creep testing was carried out at different temperatures of 300°C, 350°C and 400 °C with stress 124.77MPa, 187.16MPa, 249.55 MPa using a 1.0 mm diameter WC indenter. Experiments were conducted till the curve enters the steady state creep region. Constitutive modeling of creep behavior was carried out considering the temperature, stress and steady state creep rate. Microstructural investigation of the crept specimen at 400°C temperature and 187.16 MPa load was carried out and found that the small precipitates accumulate along the grain boundaries at the favorable conditions of the creep temperature and stress, new precipitates evolve due to the ageing. The grains are broken and deformed due to the creep phenomena.

Diamond-anvil cell observations of a new methane hydrate phase in the 100-MPa pressure range

USGS Publications Warehouse

Chou, I.-Ming; Sharma, A.; Burruss, R.C.; Hemley, R.J.; Goncharov, A.F.; Stern, L.A.; Kirby, S.H.

2001-01-01

A new high-pressure phase of methane hydrate has been identified based on its high optical relief, distinct pressure-temperature phase relations, and Raman spectra. In-situ optical observations were made in a hydrothermal diamond-anvil cell at temperatures between -40?? and 60 ??C and at pressures up to 900 MPa. Two new invariant points were located at -8.7 ??C and 99 MPa for the assemblage consisting of the new phase, structure I methane hydrate, ice Ih, and water, and at 35.3 ??C and 137 MPa for the new phase-structure I methane hydrate-water-methane vapor. Existence of the new phase is critical for understanding the phase relations among the hydrates at low to moderate pressures, and may also have important implications for understanding the hydrogen bonding in H2O and the behavior of water in the planetary bodies, such as Europa, of the outer solar system.

A Lattice-Misfit-Dependent Damage Model for Non-linear Damage Accumulations Under Monotonous Creep in Single Crystal Superalloys

NASA Astrophysics Data System (ADS)

le Graverend, J.-B.

2018-05-01

A lattice-misfit-dependent damage density function is developed to predict the non-linear accumulation of damage when a thermal jump from 1050 °C to 1200 °C is introduced somewhere in the creep life. Furthermore, a phenomenological model aimed at describing the evolution of the constrained lattice misfit during monotonous creep load is also formulated. The response of the lattice-misfit-dependent plasticity-coupled damage model is compared with the experimental results obtained at 140 and 160 MPa on the first generation Ni-based single crystal superalloy MC2. The comparison reveals that the damage model is well suited at 160 MPa and less at 140 MPa because the transfer of stress to the γ' phase occurs for stresses above 150 MPa which leads to larger variations and, therefore, larger effects of the constrained lattice misfit on the lifetime during thermo-mechanical loading.

Design and Fabrication of 3D printed Scaffolds with a Mechanical Strength Comparable to Cortical Bone to Repair Large Bone Defects

PubMed Central

Roohani-Esfahani, Seyed-Iman; Newman, Peter; Zreiqat, Hala

2016-01-01

A challenge in regenerating large bone defects under load is to create scaffolds with large and interconnected pores while providing a compressive strength comparable to cortical bone (100–150 MPa). Here we design a novel hexagonal architecture for a glass-ceramic scaffold to fabricate an anisotropic, highly porous three dimensional scaffolds with a compressive strength of 110 MPa. Scaffolds with hexagonal design demonstrated a high fatigue resistance (1,000,000 cycles at 1–10 MPa compressive cyclic load), failure reliability and flexural strength (30 MPa) compared with those for conventional architecture. The obtained strength is 150 times greater than values reported for polymeric and composite scaffolds and 5 times greater than reported values for ceramic and glass scaffolds at similar porosity. These scaffolds open avenues for treatment of load bearing bone defects in orthopaedic, dental and maxillofacial applications. PMID:26782020

Mechanical properties and microstructures of China low activation martensitic steel compared with JLF-1

NASA Astrophysics Data System (ADS)

Li, Y.; Huang, Q.; Wu, Y.; Nagasaka, T.; Muroga, T.

2007-08-01

The tensile and impact properties of CLAM steel are compared to those of JLF-1 steel. Tensile testing revealed that the ultimate and yield strengths of the CLAM steel are 670 MPa and 512 MPa at room temperature, and 373 MPa and 327 MPa at 873 K, respectively. These values are higher than those measured for JLF-1. The ductile-to-brittle transition temperature (DBTT) of CLAM was found to be 171 K using one-third size Charpy V-notch specimens, which is 16 K lower than that of JLF-1. Microstructural analysis by SEM and TEM indicated that the prior austenite grain size and lath width for CLAM are smaller than those for JLF-1. The finer grain and lath structure is considered to be one of the main reasons for the higher strength and lower DBTT of the CLAM steel.

Design and Fabrication of 3D printed Scaffolds with a Mechanical Strength Comparable to Cortical Bone to Repair Large Bone Defects

NASA Astrophysics Data System (ADS)

Roohani-Esfahani, Seyed-Iman; Newman, Peter; Zreiqat, Hala

2016-01-01

A challenge in regenerating large bone defects under load is to create scaffolds with large and interconnected pores while providing a compressive strength comparable to cortical bone (100-150 MPa). Here we design a novel hexagonal architecture for a glass-ceramic scaffold to fabricate an anisotropic, highly porous three dimensional scaffolds with a compressive strength of 110 MPa. Scaffolds with hexagonal design demonstrated a high fatigue resistance (1,000,000 cycles at 1-10 MPa compressive cyclic load), failure reliability and flexural strength (30 MPa) compared with those for conventional architecture. The obtained strength is 150 times greater than values reported for polymeric and composite scaffolds and 5 times greater than reported values for ceramic and glass scaffolds at similar porosity. These scaffolds open avenues for treatment of load bearing bone defects in orthopaedic, dental and maxillofacial applications.

Effect of high hydrostatic pressure and whey proteins on the disruption of casein micelle isolates.

PubMed

Harte, Federico M; Gurram, Subba Rao; Luedecke, Lloyd O; Swanson, Barry G; Barbosa-Cánovas, Gustavo V

2007-11-01

High hydrostatic pressure disruption of casein micelle isolates was studied by analytical ultracentrifugation and transmission electron microscopy. Casein micelles were isolated from skim milk and subjected to combinations of thermal treatment (85 degrees C, 20 min) and high hydrostatic pressure (up to 676 MPa) with and without whey protein added. High hydrostatic pressure promoted extensive disruption of the casein micelles in the 250 to 310 MPa pressure range. At pressures greater than 310 MPa no further disruption was observed. The addition of whey protein to casein micelle isolates protected the micelles from high hydrostatic pressure induced disruption only when the mix was thermally processed before pressure treatment. The more whey protein was added (up to 5 g/l) the more the protection against high hydrostatic pressure induced micelle disruption was observed in thermally treated samples subjected to 310 MPa.

Survival and growth of Yersinia enterocolitica strains inoculated in skimmed milk treated with high hydrostatic pressure.

PubMed

De Lamo-Castellví, Sílvia; Roig-Sagués, Artur X; Capellas, Marta; Hernández-Herrero, Manuela; Guamis, Buenaventura

2005-07-25

Four human pathogenic strains of Yersinia enterocolitica (serotypes O:1, O:3, O:8, and O:9) were inoculated (7-8 log CFU/ml) in UHT skimmed milk and treated at 300, 400, and 500 MPa for 10 min at 20 degrees C, and then kept at 8 degrees C to assess their evolution for 15 days. Treatments at 400 and 500 MPa caused the highest lethality, generally reaching counts below detection level (1 CFU/ml) in the culture media. At 300 MPa, the most baroresistant serotypes were O:3 and O:8. After 15 days of storage at 8 degrees C, Y. enterocolitica showed growth over 8 log (CFU/ml) in all treatments. Kinetic study of microbial inactivation in skimmed milk was performed with serotype O:8 at 300 MPa, showing a tailing after 35 min of pressure treatment.

Effects of high pressure treatment and temperature on lipid oxidation and fatty acid composition of yak (Poephagus grunniens) body fat.

PubMed

Wang, Qiang; Zhao, Xin; Ren, Yanrong; Fan, Enguo; Chang, Haijun; Wu, Hongbin

2013-08-01

Effects of high-pressure treatment (100 MPa to 600 MPa) on lipid oxidation and composition of fatty acids in yak body fat at 4 °C and 15 °C were investigated for up to 20 days storage. 400 and 600 MPa treatments increase the level of thiobarbituric acid-reactive substances (TBARS) 335% and 400% (p<0.05), respectively. Composition analysis shows that 600 MPa treatment induces a lower (p<0.05) percentage of polyunsaturated fatty acids, and C22:6 decreased significantly. A significant decrease in PUFA/SFA and n-6/n-3 PUFA values was observed at the end of storage. Samples treated at the lower pressures gave good sensory acceptability. It is concluded that a higher-pressure treatment is important in catalyzing lipid oxidation and the evolution of fatty acids in pressure-treated yak body fat. Copyright © 2013 Elsevier Ltd. All rights reserved.

Study of the effect of surface treatment of kenaf fibre on mechanical properties of kenaf filled unsaturated polyester composite

NASA Astrophysics Data System (ADS)

Salem, I. A. S.; Rozyanty, A. R.; Betar, B. O.; Adam, T.; Mohammed, M.; Mohammed, A. M.

2017-10-01

In this research, unsaturated polyester/kenaf fiber (UP/KF) composites was prepared by using hand lay-up process. The effect of surface treatment of kenaf fiber on mechanical properties of kenaf filled unsaturated polyester composites were studied. Different concentrationsof stearic acid (SA) were applied, i.e. 0, 0.4, and 0.8 wt%. Tensile strength of untreated UP/KF composites was found to be higher for 40 wt% loading of kenaf fiber. The highest tensile strength value was obtained after treatment with 0.4 wt% concentration of stearic acid at 56 MPa and tensile modulus was at 2409 MPa. From the flexural strength result obtained, it is clearly seen that 40 wt% loading of kenaf fiber and treatment with 0.4 wt% concentration of stearic acid give the highest value at 72 MPa and flexural modulus at 3929 MPa.

Microstructure evolution of fault rocks at the "brittle-to-plastic" transition

NASA Astrophysics Data System (ADS)

Heilbronner, R.; Pec, M.; Stunitz, H.

2011-12-01

In the continental crust, large earthquakes tend to nucleate at the "brittle-to-plastic" transition at depths of ~ 10 - 20 km indicating stress release by rupture at elevated PT. Experimental studies, field observations, and models predict peak strength of the lithosphere at depths where rocks deform by "semi-brittle" flow. Thus, the deformation processes taking place at these conditions are important aspects of the seismic cycle and fault rheology in general. We performed a series of experiments with crushed Verzasca gneiss powder (d ≤ 200 μm), "pre-dried" and 0.2 wt% H2O added, placed between alumina forcing blocks (45° pre-cut) and weld-sealed in Pt jackets. The experiments were performed at Pc = 500, 1000 and 1500 MPa, T = 300°C and 500°C. and shear strain rates of ~10-3 s-1 to ~10-5 s-1 in a solid medium deformation apparatus (Griggs rig). Samples deformed at Pc = 500 MPa attain peak strength (~ 1100-1400 MPa) at γ ~ 2, they weaken by ~20 MPa (300°C) to ~140 MPa (500°C) and reach a steady state. The 300°C experiments are systematically stronger by ~ 330 - 370 MPa than the 500°C experiments, and flow stress increases with increasing strain rate. At Pc = 1000 and 1500 MPa, peak strength (~1300-1600 MPa) is reached at γ = 1 to 1.5 followed by weakening of ~60 (300°C) and ~150 MPa (500°C). The strength difference between 300°C and 500°C samples is 270-330 MPa and does not increase with increasing confining pressure. The peak strength increase with confining pressure is modest (50-150 MPa), indicating that the rocks reach their maximal compressive strength. The microstructure develops as an S-C-C' fabric with dominant C' slip zones. At low strains, the gouge zone is pervasively cut by closely spaced C' shears containing fine-grained material (d < 100 nm). At peak strength, deformation localizes into less densely spaced, ~10 μm thick C'-C slip zones which develop predominantly in feldspars. In TEM, they show no porosity and consist of amorphous material and small crystalline fragments (d ~ 20 nm). During steady state flow, pseudotachylites appear as isolated patches, typically associated with micas (melting temperature ~650°C). Quartz grains show the lowest degree of fragmentation and represent the rheologically strongest phase. Feldspar grains fracture more easily and are the weakest phase. The development of the bulk microstructure evolves with finite strain and does not show any dependence on temperature. CL observations, EDS maps and WDS microprobe data show changes in chemical composition in the slip zones indicating that mechanical disintegration of the grains is accompanied by transport of alkalis, producing a different mineral chemistry even at short experimental time scales (~20 min to 30 hrs). The amorphous to nano-crystalline material is viscously deformed and a pre-cursor for the formation of frictional melt, which is typically more ferromagnesian and basic than the bulk rock composition. Our results indicate that 1) frictional melting can occur even at slow strain-rates 2) is possible during steady-state plastic flow and is not accompanied by a stress drop.

Processing, Structural Characterization and Comparative Studies on Uniaxial Tensile Properties of a New Type of Porous Twisted Wire Material

PubMed Central

Wu, Fei; Zhou, Zhaoyao; Duan, Liuyang; Xiao, Zhiyu

2015-01-01

A self-developed rotary multi-cutter device cuts stainless steel wire ropes into segments to fabricate twisted wires. Stainless steel porous twisted wire materials (PTWMs) with a spatial composite intertexture structure are produced by the compaction and subsequent vacuum solid-phase sintering of twisted wires. The stainless steel PTWMs show two types of typical uniaxial tensile failure modes, i.e., a 45° angle fracture mode and an auxetic failure mode (the PTWMs expand along the direction perpendicular to the tension). The effects of the sintering parameters, porosities, wire diameters, and sampling direction on the tensile properties of the PTWMs are carefully investigated. By increasing the sintering temperature from 1130 °C to 1330 °C, the tensile strength of the PTWMs with 70% target porosity increased from 7.7 MPa to 28.6 MPa and the total failure goes down to 50%. When increasing the sintering time from 90 min to 150 min, the tensile strength increases from 12.4 MPa to 19.1 MPa and the total failure elongation drops to 78.6%. The tensile strength of the PTWMs increases from 28.9 MPa to 112.7 MPa with decreasing porosity from 69.5% to 46.0%, and the total failure elongation also increases from 14.8% to 40.7%. The tensile strength and the failure strain of the PTWMs with fine wires are higher than those of the PTWMs with coarse wires under the same porosity. Sampling direction has a small influence on the tensile properties of the PTWMs. PMID:28793526

High crystalline Cu2ZnSnS4 semiconductor prepared from low toxicity ethanol-based precursors

NASA Astrophysics Data System (ADS)

Munir, Badrul; Prastyo, Bayu Eko; Nurjaya, Dwi Marta; Muslih, Ersan Yudhapratama; Alfauzan, Sahri Karim

2017-01-01

At this moment, we present a new, cost-effective, and environmentally friendly method of preparing a high crystalline Cu2ZnSnS4 (CZTS) absorber layer for thin film solar cells using ethanol-based solutions. Ethanolamine (ETA) and 2-mercaptopropionic acid (MPA) were studied as a stabilizer and to improve wetting ability of the precursors during the deposition process. Cu2ZnSnS4 precursors are deposited onto soda lime glass using spin coater in different molar of cations in the precursor. The effects of a precursor system, ethanol-ETA-MPA, and ethanol-MPA, on the structure, morphology, composition and optical properties of CZTS thin films have been investigated in details. X-ray diffraction and energy-dispersive X-ray spectroscopy analyses confirmed the successful fabrication of high crystalline Cu2ZnSnS4 kesterite phase. The crystallinity of CZTS is continue increasing before reaching 2.2 molar cations of the ethanol-MPA precursors. The crystallinity of ethanol-ETA-MPA precursors remains similar in the experiment using 1.2 molar and 1.6 molars. The highest crystallinity was achieved using 2 molar cations of the ethanol-MPA precursor. Its band gap energy is found to be around 1.4 eV. The SEM micrographs of CZTS film shows the average grain size around 1.5 µm and some porosity which indicated the room of improvement. The high-crystallinity CZTS achieved in the present study brings a low-cost absorber semiconductor one step closer to practical use.

Synergistic Effects of High Hydrostatic Pressure, Mild Heating, and Amino Acids on Germination and Inactivation of Clostridium sporogenes Spores

PubMed Central

Ishimori, Takateru; Takahashi, Katsutoshi; Goto, Masato; Nakagawa, Suguru; Kasai, Yoshiaki; Konagaya, Yukifumi; Batori, Hiroshi; Kobayashi, Atsushi

2012-01-01

The synergistic effects of high hydrostatic pressure (HHP), mild heating, and amino acids on the germination of Clostridium sporogenes spores were examined by determining the number of surviving spores that returned to vegetative growth after pasteurization following these treatments. Pressurization at 200 MPa at a temperature higher than 40°C and treatment with some of the 19 l-amino acids at 10 mM or higher synergistically facilitated germination. When one of these factors was omitted, the level of germination was insignificant. Pressures of 100 and 400 MPa were less effective than 200 MPa. The spores were effectively inactivated by between 1.8 and 4.8 logs by pasteurization at 80°C after pressurization at 200 MPa at 45°C for 120 min with one of the amino acids with moderate hydrophobicity, such as Leu, Phe, Cys Met, Ala, Gly, or Ser. However, other amino acids showed poor inactivation effects of less than 0.9 logs. Spores in solutions containing 80 mM of either Leu, Phe, Cys, Met, Ala, Gly, or Ser were successfully inactivated by pasteurization by more than 5.4 logs after pressurization at 200 MPa at 70°C for 15 to 120 min. Ala and Met reduced the spore viability by 2.8 and 1.8 logs, respectively, by pasteurization at a concentration of 1 mM under 200 MPa at 70°C. These results indicate that germination of the spores is facilitated by a combination of high hydrostatic pressure, mild heating, and amino acids. PMID:22983975

High pressure processing of meat: effects on ultrastructure and protein digestibility.

PubMed

Kaur, Lovedeep; Astruc, Thierry; Vénien, Annie; Loison, Olivier; Cui, Jian; Irastorza, Marion; Boland, Mike

2016-05-18

The effects of high pressure processing (HPP, at 175 and 600 MPa) on the ultrastructure and in vitro protein digestion of bovine longissimus dorsi muscle meat were studied. HPP caused a significant change in the visual appearance and texture of the meat subjected to HPP at 600 MPa so that it appeared similar to cooked meat, unlike the meat subjected to HPP at 175 MPa that showed no significant visible change in the colour and texture compared to the raw meat. The muscles were subjected to digestion under simulated gastric conditions for 1 h and then under simulated small-intestinal conditions for a further 2 h. The digests were analysed using gel electrophoresis (SDS-PAGE) and ninhydrin assay for amino N. The effect of the acid conditions of the stomach alone was also investigated. Reduced SDS-PAGE results showed that pepsin-digested (60 min) HPP meats showed fewer proteins or peptides of high molecular weight than the pepsin-digested untreated meat, suggesting more breakdown of the parent proteins in HPP-treated meats. This effect was more pronounced in the muscles treated at 600 MPa. These results are in accordance with microscopy results, which showed greater changes in the myofibrillar structure after simulated gastric digestion of the sample processed at 600 MPa than at 175 MPa. Transmission electron microscopy also showed the presence of protein aggregates in the former sample, resulting probably from protein denaturation of sarcoplasmic proteins, in the subcellular space and between myofibrils; along with cell contraction (similar to that caused by heating) in the former.

Determination of extremely high pressure tolerance of brine shrimp larvae by using a new pressure chamber system.

PubMed

Seo, Mihye; Koyama, Sumihiro; Toyofuku, Takashi; Kojima, Shigeaki; Watanabe, Hiromi

2013-11-01

Hydrostatic pressure is the only one of a range of environmental parameters (water temperature, salinity, light availability, and so on) that increases in proportion with depth. Pressure tolerance is therefore essential to understand the foundation of populations and current diversity of faunal compositions at various depths. In the present study, we used a newly developed pressure chamber system to examine changes in larval activity of the salt-lake crustacean, Artemia franciscana, in response to a range of hydrostatic pressures. We showed that A. franciscana larvae were able to survive for a short period at pressures of ≤ 60 MPa (approximately equal to the pressure of 6000 m deep). At a pressure of > 20 MPa, larval motor ability was suppressed, but not lost. Meanwhile, at a pressure of > 40 MPa, some of the larval motor ability was lost without recovery after decompression. For all experiments, discordance of movement and timing between right and left appendages, was observed at pressures of > 20 MPa. Our results indicate that the limit of pressure for sustaining active behavior of A. franciscana larvae is ∼20 MPa, whereas the limit of pressure for survival is within the range 30-60 MPa. Thus, members of the genus Artemia possess the ability to resist a higher range of pressures than their natural habitat depth. Our findings demonstrated an example of an organism capable of invading deeper environment in terms of physical pressure tolerance, and indicate the need and importance of pressure study as an experimental method.

The effect of hormone therapy on plasma homocysteine levels: a randomized clinical trial.

PubMed

Tutuncu, Levent; Ergur, Ali Rustu; Mungen, Ercument; Gun, Ismet; Ertekin, Aktug; Yergok, Yusuf Ziya

2005-03-01

An elevated plasma homocysteine level is a risk factor for cardiovascular diseases. Hormone therapy (HT) may reduce fasting plasma homocysteine levels. We studied 80 postmenopausal women to determine the effect of medroxyprogesterone acetate (MPA) combined with conjugated equine estrogens (CEE) on fasting plasma homocysteine levels. In a randomized, double blind, prospective, placebo-controlled study, we randomly assigned 80 healthy postmenopausal women between CEE 0.625 mg/d combined with MPA 2.5 mg/d (n = 20), CEE 0.625 mg/d combined with MPA 5 mg/d (n = 20), unopposed CEE 0.625 mg/d (n = 20), and placebo (n = 20) all given for a duration of 6 months. Fasting plasma homocysteine levels were measured before and at the end of the treatment. Before treatment, plasma homocysteine concentrations were similar in all groups. After 6 months of unopposed CEE, the mean fasting plasma homocysteine levels decreased by 19.02% when compared with baseline levels (P < 0.05). The mean fasting plasma homocysteine concentrations decreased by 17.63% and 19.56% from baseline in both the CEE plus MPA 2.5 mg/d and CEE plus MPA 5 mg/d groups, respectively (P < 0.05 for each group). In contrast, plasma homocysteine levels increased by 11.66% in the placebo group. The homocysteine lowering effect did not differ significantly among the three groups of women receiving unopposed CEE alone and CEE plus MPA at two different doses. Six months of estrogen therapy (ET) and combined estrogen-progestogen therapy (EPT) significantly lower fasting plasma homocysteine levels in healthy postmenopausal women with equal efficacy.

Conservative decrease in water potential in existing leaves during new leaf expansion in temperate and tropical evergreen Quercus species.

PubMed

Saito, Takami; Naiola, B Paul; Terashima, Ichiro

2007-12-01

This study aimed at clarifying how the water potential gradient (deltapsi) is maintained in the shoots of evergreen trees with expanding leaves, whose leaf water potentials at the turgor loss point (psi(tlp)) are generally high. The water relations were examined in current-year expanding (CEX) and 1-year-old (OLD) leaves on the same shoots in temperate (Osaka, Japan) and tropical (Bogor, Indonesia) areas. A temperate evergreen species, Quercus glauca growing in both sites, was compared with a temperate deciduous species, Q. serrata, in Osaka, and two tropical evergreen species, Q. gemelliflora and Q. subsericea, in Bogor. (1) In Osaka, the midday leaf water potential (psi(midday)) was slightly higher in OLD (-0.5 MPa) than in CEX leaves (-0.6 MPa), whereas psi(tlp) was significantly lower in OLD (-2.9 MPa) than in CEX leaves (-1.0 MPa). In Bogor, psi(midday) was also higher in OLD leaves (-1.0 MPa) despite the low psi(tlp) (-1.9 MPa), although stomatal conductance was not always low in OLD leaves. In the branch bearing CEX and OLD leaves, most of the hydraulic resistance (86 %) exists in the current-year branch, leading to differences in water supply between CEX and OLD leaves. The removal of buds just before breaking did not affect the high psi(midday) in OLD leaves after 1 month. Psi(midday) in OLD leaves thus appears to be independent of that in CEX leaves. The moderate decrease in psi(midday) in OLD leaves would contribute to maintenance of deltapsi in the shoots during leaf expansion.

Role of cold isostatic pressing in the formation of the properties of ZrO{sub 2}-base ceramics obtained from ultradisperse powders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Akimov, G.Y.; Prokhorov, I.Y.; Gorelik, I.V.

1995-09-01

The physicomechanical properties of ceramics obtained from plasmachemical and sol-gel powders of partially stabilized (3% Y{sub 2}O{sub 3}) zirconia (PSZ) and its compositions with 20% Al{sub 2}O{sub 3} by cold isostatic pressing (CIP) at a pressure of at most 2 GPa and sintering at 1300-1650{degrees}C are investigated. It is established that plasmachemical PSZ exhibits its best properties (K{sub 1c} = 7.8 MPa {center_dot} m{sup 1/2}, a strength of 650 MPa) only after complete disintegration at a CIP of 0.1 GPa and a sintering temperature of 1650{degrees}C, when the material is sintered to a density of 5.5 g/cm{sup 3}. After partialmore » stabilization and CIP at 0.1 GPa the plasmachemical composition of PSZ + 20% Al{sub 2}O{sub 3} is sintered at 1650{degrees}C to a density of 4.7 g/cm{sup 3}, but has K{sub 1c} = 8.5 MPa {center_dot} m{sup 1/2} and a strength of 700 MPa. The deagglomerated sol-gel powder exhibits properties at a level of K{sub 1c} = 12.4 MPa {center_dot} m{sup 1/2} and a strength of 950 MPa at a density above 6.0 g/cm{sup 3} after CIP at 0.3 GPa and sintering at 1450{degrees}C. The latter obviously has the best mechanical properties of all the investigated materials.« less

Processing, Structural Characterization and Comparative Studies on Uniaxial Tensile Properties of a New Type of Porous Twisted Wire Material.

PubMed

Wu, Fei; Zhou, Zhaoyao; Duan, Liuyang; Xiao, Zhiyu

2015-08-27

A self-developed rotary multi-cutter device cuts stainless steel wire ropes into segments to fabricate twisted wires. Stainless steel porous twisted wire materials (PTWMs) with a spatial composite intertexture structure are produced by the compaction and subsequent vacuum solid-phase sintering of twisted wires. The stainless steel PTWMs show two types of typical uniaxial tensile failure modes, i.e. , a 45° angle fracture mode and an auxetic failure mode (the PTWMs expand along the direction perpendicular to the tension). The effects of the sintering parameters, porosities, wire diameters, and sampling direction on the tensile properties of the PTWMs are carefully investigated. By increasing the sintering temperature from 1130 °C to 1330 °C, the tensile strength of the PTWMs with 70% target porosity increased from 7.7 MPa to 28.6 MPa and the total failure goes down to 50%. When increasing the sintering time from 90 min to 150 min, the tensile strength increases from 12.4 MPa to 19.1 MPa and the total failure elongation drops to 78.6%. The tensile strength of the PTWMs increases from 28.9 MPa to 112.7 MPa with decreasing porosity from 69.5% to 46.0%, and the total failure elongation also increases from 14.8% to 40.7%. The tensile strength and the failure strain of the PTWMs with fine wires are higher than those of the PTWMs with coarse wires under the same porosity. Sampling direction has a small influence on the tensile properties of the PTWMs.

Water stress impacts on bacterial carbon monoxide oxidation on recent volcanic deposits.

PubMed

Weber, Carolyn F; King, Gary M

2009-12-01

Water availability oscillates dramatically on young volcanic deposits, and may control the distribution and activity of microbes during early stages of biological succession. Carbon monoxide (CO)-oxidizing bacteria are among the pioneering colonists on volcanic deposits and are subjected to these water stresses. We report here the effects of water potential on CO-oxidizing bacteria in unvegetated (bare) and vegetated (canopy) sites on a 1959 volcanic deposit on Kilauea Volcano (Hawai'i). Time course measurements of water potential showed that average water potentials in the surface layer (0-1 cm) of canopy soil remained between -0.1 and 0 MPa, whereas dramatic diurnal oscillations (for example, between -60 and 0 MPa) occur in bare site surface cinders. During a moderate drying event in situ (-1.7 to 0 MPa), atmospheric CO consumption by intact bare site cores decreased 2.7-fold. For bare and canopy surface samples, maximum potential CO oxidation rates decreased 40 and 60%, respectively, when water potentials were lowered from 0 to -1.5 MPa in the laboratory. These observations indicated that CO oxidation is moderately sensitive to changes in water potential. Additional analyses showed that CO oxidation resumes within a few hours of rehydration, even after desiccation at -150 MPa for 63 days. Samples from both sites exposed to multiple cycles of drying and rewetting (-80 to 0 MPa), lost significant activity after the first cycle, but not after subsequent cycles. Similar responses of CO oxidation in both sites suggested that active CO-oxidizing communities in bare and canopy sites do not express differential adaptations to water stress.

Density, Microstructure, Strength and Fractography of Spark Plasma and Conventionally Sintered Mn Steels

NASA Astrophysics Data System (ADS)

Tenerowicz-Zaba, M.; Kupkova, M.; Kabatova, M.; Dudrova, E.; Dzupon, M.; Sulowski, M.

2017-12-01

The aim of the study was to investigate Spark Plasma Sintering (SPS) of 1-3%Mn steels and compare the resultant microstructures, strengths and failure mechanisms with those of conventionally sintered materials. SPS was performed in a vacuum of 5 Pa at 1000°C for 15min under a uniaxial pressure of 20 MPa. The heating rate of 100°C/min was applied. For conventional processing, mixtures of powders were prepared in a Turbula mixer for 30 minutes. Samples were single pressed at 660 MPa, according to PN-EN ISO 2740 standard. Sintering of compacts was carried out in a laboratory tube furnace at 1120°C and 1250°C for 60 minutes in a mixture of 95%N2-5%H2. Heating and cooling rates were 75C°/min and 60°C/min, respectively. The density of SPS samples was higher (up to 7.37 g/cm3) than those after conventional sintering (up to 6.7 g/cm3). Yield strengths of SPS samples were in the range 920-1220 MPa, compared to the maximum of 602 MPa for conventionally sintered Fe-3%Mn-0.8%C. Transverse rupture strengths were the same for this alloy, 1234 MPa, but reached 1473 MPa for SPS 2Mn variant. Interfaces in SPS samples were significantly less contaminated with oxides, which is the result of a more favorable microclimate and pressure acting during SPS. These preliminary results indicate that further research on the SPS of Mn steels is warranted.

Influence of surface conditions and silane agent on the bond of resin to IPS Empress 2 ceramic.

PubMed

Spohr, Ana Maria; Sobrinho, Lourenço Correr; Consani, Simonides; Sinhoreti, Mario Alexandre Coelho; Knowles, Jonathan C

2003-01-01

The aim of this study was to evaluate the effect of different ceramic surface treatments on the tensile bond strength between IPS Empress 2 ceramic framework and Rely X adhesive resin cement, with or without the application of a silane coupling agent. One hundred twenty disks were made, embedded in resin, and randomly divided into six groups: group 1 = sandblasting (100 microm), no silanation; group 2 = sandblasting (100 microm), silane treatment; group 3 = sandblasting (50 microm), no silanation; group 4 = sandblasting (50 microm), silane treatment; group 5 = hydrofluoric acid etching, no silanation; and group 6 = hydrofluoric acid etching, silane treatment. The disks were bonded into pairs with adhesive resin cement. All samples were stored in distilled water at 37 degrees C for 24 hours and then thermocycled. The samples were submitted to tensile testing. The use of silane improved the bond strength in relation to the groups in which silane was not applied (P < .05). The most effective surface treatment was etching with 10% hydrofluoric acid, both with (25.6 MPa) and without silane application (16.4 MPa); these values showed a statistically significant difference compared to sandblasting with 50- and 100-microm Al2O3. Sandblasting with 50-microm Al2O3, with (11.8 MPa) and without silane (5.4 MPa), demonstrated significantly higher tensile bond strength than sandblasting with 100-microm Al2O3, with (8.3 MPa) and without silane (3.8 MPa). Combined application of 10% hydrofluoric acid and silane enhanced the bond strength between the IPS Empress 2 ceramic framework and resin agent.

Nanocrystalline-grained tungsten prepared by surface mechanical attrition treatment: Microstructure and mechanical properties

NASA Astrophysics Data System (ADS)

Guo, Hong-Yan; Xia, Min; Wu, Zheng-Tao; Chan, Lap-Chung; Dai, Yong; Wang, Kun; Yan, Qing-Zhi; He, Man-Chao; Ge, Chang-Chun; Lu, Jian

2016-11-01

A nanostructured surface layer was fabricated on commercial pure tungsten using the method of surface mechanical attrition treatment (SMAT). The microstructure evolution of the surface layer was characterized by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and its formation mechanism was discussed as well. Both refinement and elongation of the brittle W grains were confirmed. The elongated SMATed W was heavily strained, the maximum value of the strain at the grain boundaries reaches as high as 3-5%. Dislocation density in the SMATed W nanograins was found to be 5 × 1012 cm-2. The formation of the nanograins in the top surface layer of the W was ascribed to the extremely high strain and strain rate, as well as the multidirectional repetitive loading. Bending strength of commercial W could be improved from 825 MPa to 1850 MPa by SMAT process. Microhardness results indicated the strain range in SMATed W can reach up to 220 μm beneath the top surface. The notched Charpy testing results demonstrated that SMATed W possess higher ductility than that of commercial W. The top surface of the W plates with and without SMATe processing possesses residual compressive stress of about -881 MPa and -234 MPa in y direction, and -872 MPa and -879 MPa in x direction respectively. The improvement of toughness (DBTT shift) of SMATed W may be the synergistic effect of residual compressive stress, dislocation density improvement and microstructure refinement induced by SMAT processing. SMAT processing could be a complementary method to further decrease the DBTT value of tungsten based materials.

Modified ring stretch tensile testing of Zr-1Nb cladding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cohen, A.B.; Majumdar, S.; Ruther, W.E.

1998-03-01

In a round robin effort between the US Nuclear Regulatory Commission, Institut de Protection et de Surete Nucleaire in France, and the Russian Research Centre-Kurchatov Institute, Argonne National Laboratory conducted 16 modified ring stretch tensile tests on unirradiated samples of zr-1Nb cladding, which is used in Russian VVER reactors. Test were conducted at two temperatures (25 and 400 C) and two strain rates (0.001 and 1 s{sup {minus}1}). At 25 C and 0.001 s{sup {minus}1}, the yield strength (YS), ultimate tensile strength (UTS), uniform elongation (UE), and total elongation (TE) were 201 MPa, 331 MPa, 18.2%, and 57.6%, respectively. Atmore » 400 C and 0.001 s{sup {minus}1}, the YS, UTS, UE, and TE were 109 MPa, 185 MPa, 15.4%, and 67.7%, respectively. Finally, at 400 C and 1 s{sup {minus}1}, the YS, UTS, UE, and TE were 134 MPa, 189 MPa, 18.9%, and 53.4%, respectively. The high strain rate tests at room temperature were not successful. Test results proved to be very sensitive to the amount of lubrication used on the inserts; because of the large contact area between the inserts and specimen, too little lubrication leads to significantly higher strengths and lower elongations being reported. It is also important to note that only 70 to 80% of the elongation takes place in the gauge section, depending on specimen geometry. The appropriate percentage can be estimated from a simple model or can be calculated from finite-element analysis.« less

The material from Lampung as coarse aggregate to substitute andesite for concrete-making

NASA Astrophysics Data System (ADS)

Amin, M.; Supriyatna, Y. I.; Sumardi, S.

2018-01-01

Andesite stone is usually used for split stone material in the concrete making. However, its availability is decreasing. Lampung province has natural resources that can be used for coarse aggregate materials to substitute andesite stone. These natural materials include limestone, feldspar stone, basalt, granite, and slags from iron processing waste. Therefore, a research on optimizing natural materials in Lampung to substitute andesite stone for concrete making is required. This research used laboratory experiment method. The research activities included making cubical object samples of 150 x 150 x 150 mm with material composition referring to a standard of K.200 and w/c 0.61. Concrete making by using varying types of aggregates (basalt, limestone, slag) and aggregate sizes (A = 5-15 mm, B = 15-25 mm, and 25-50 mm) was followed by compressive strength test. The results showed that the obtained optimal compressive strengths for basalt were 24.47 MPa for 50-150 mm aggregate sizes, 21.2 MPa for 15-25 mm aggregate sizes, and 20.7 MPa for 25-50 mm aggregate sizes. These results of basalt compressive strength values were higher than the same result for andesite (19.69 MPa for 50-150 mm aggregate sizes), slag (22.72 MPa for 50-150 mm aggregate sizes), and limestone (19.69 Mpa for 50-150 mm aggregate sizes). These results indicated that basalt, limestone, and slag aggregates were good enough to substitute andesite as materials for concrete making. Therefore, natural resources in Lampung can be optimized as construction materials in concrete making.

Effects of tributylborane-activated adhesive and two silane agents on bonding computer-aided design and manufacturing (CAD/CAM) resin composite.

PubMed

Shinohara, Ayano; Taira, Yohsuke; Sawase, Takashi

2017-10-01

The present study was conducted to evaluate the effects of an experimental adhesive agent [methyl methacrylate-tributylborane liquid (MT)] and two adhesive agents containing silane on the bonding between a resin composite block of a computer-aided design and manufacturing (CAD/CAM) system and a light-curing resin composite veneering material. The surfaces of CAD/CAM resin composite specimens were ground with silicon-carbide paper, treated with phosphoric acid, and then primed with either one of the two silane agents [Scotchbond Universal Adhesive (SC) and GC Ceramic Primer II (GC)], no adhesive control (Cont), or one of three combinations (MT/SC, MT/GC, and MT/Cont). A light-curing resin composite was veneered on the primed CAD/CAM resin composite surface. The veneered specimens were subjected to thermocycling between 4 and 60 °C for 10,000 cycles, and the shear bond strengths were determined. All data were analyzed using analysis of variance and a post hoc Tukey-Kramer HSD test (α = 0.05, n = 8). MT/SC (38.7 MPa) exhibited the highest mean bond strengths, followed by MT/GC (30.4 MPa), SC (27.9 MPa), and MT/Cont (25.7 MPa), while Cont (12.9 MPa) and GC (12.3 MPa) resulted in the lowest bond strengths. The use of MT in conjunction with a silane agent significantly improved the bond strength. Surface treatment with appropriate adhesive agents was confirmed as a prerequisite for veneering CAD/CAM resin composite restorations.

The influence of total suction on the brittle failure characteristics of clay shales

NASA Astrophysics Data System (ADS)

Amann, F.; Linda, W.; Zimmer, S.; Thoeny, R.

2013-12-01

Clay shale testing is challenging and the results obtained from standard laboratory tests may not always reflect the strength of the clay shale in-situ. This is to a certain extend associated with the sensitivity of these rock types to desaturation processes during drilling, sample storage, and sample preparation. In this study the relationship between total suction, uniaxial compressive strength and Brazilian tensile (BTS) strength of cylindrical samples of Opalinus Clay was established in a systematic manner. Unconfined uniaxial compression and BTS tests were performed utilizing a servo-controlled testing procedure. Total suctions in the specimens was generated in air tight desiccators using supersaturated saline solutions which establish a relative humidity ranging from 20% to 99%. For unconfined compressive strength tests loading of the specimens occurred parallel to bedding. For BTS tests loading was either oriented normal or perpendicular to bedding. Both, the crack initiation and volumetric strain reversal threshold values were determined using volumetric and radial stress-strain methods. The results of BTS tests show that the tensile strength normal and perpendicular to bedding increases by a factor of approximately 3 when total suction is increased from 0 to 90 MPa (i.e. saturation decreases from 1.0 to 0.7) . Beyond 90 MPa total suction no further increase in tensile strength was observed, most probably due to shrinkage cracks which alter the tensile strength of the clay shale. Results obtained from UCS tests suggest that higher total suctions result in higher UCS values. Between total suctions of 0 to 90 MPa, the strength increase is almost linear (i.e. the UCS increases by a factor of 1.5 MPa). Beyond 90 MPa total suction no further strength increase was observed. A similar trend can be observed for crack initiation and crack damage values. In the same range of total suction the crack initiation stress increases by a factor of 5 (from 2 MPa to 10 MPa), and the crack damage stress increases by a factor of 2 (from 6 to 12 MPa). In addition to UCS tests, the water retention curve of intact and disturbed specimens was established. Here, results indicate that the drying path remains nearly unaffected by mechanical damage. However, the wetting path is considerably affected by mechanical damage.

Measured posterior annuloplasty for repair of non-ischemic mitral regurgitation. A single unit follow-up.

PubMed

Jyrala, Aarne; Gatto, Nicole M; Kay, Gregory L

2010-01-01

The aim of this report is to evaluate short- and long-term outcomes of annuloplasty method of our choice: measured posterior annuloplasty (MPA). MPA is a piece of a Duran ring cut to the length of free-edge of anterior mitral leaflet (AML) and anchored with multiple pledgeted U-sutures from trigone to trigone into the posterior annulus. From 1988 to 2000, 103 consecutive patients with non-ischemic mitral regurgitation were scheduled preoperatively to be repaired by MPA. Preoperative mitral valve regurgitation (MR) grade was 3.8+/-0.5 and decreased to 0.1+/-0.3 (P<0.0001) after repair. One patient was converted to insertion of mechanical prosthesis after grade 3 MR persisted after septal myectomy and MPA. Three patients needed instant revision of the repair one due to SAM and two due to stenosis. No patient had a stenosis or unacceptable (>1) MR after the procedure. There was one operative death (1.0%) and 3 hospital/30-day deaths (2.9%). Sixteen patients (16.3%) expired during the follow-up to 91 months (mean 57.4+/-19.5, median 60 months) none due to failure of MPA. There were no reoperations due to failure of MPA. Three patients had a reoperation, one for dehiscence of reconstruction after P2 resection and two patients due to progression of anterior leaflet degeneration and calcification with 4+ MR. New York Heart Association (NYHA) functional classification decreased from 2.3+/-0.8 to 1.4+/-0.6 (P<0.0001) and only one patient had an increase from II to III. Eighty-eight patients (96.7%) were in NYHA class I-II. Ten patients had an increase of MR from 0 to trace or 1 and one from 0 to 2. Two patients were diagnosed with mild stenosis without need of reoperation. MPA is a durable and stable alternative for repair of non-ischemic mitral regurgitation of different etiologies. The technique gives an objective measure of the length of the band and no patient is left with a significant MR or mitral valve stenosis (MS). First-time success rate is very high and instant repairs few and minor. Freedom of MPA related reoperations is 100%.

Experimental constraints on the relative stabilities of the two systems monazite-(Ce) - allanite-(Ce) - fluorapatite and xenotime-(Y) - (Y,HREE)-rich epidote - (Y,HREE)-rich fluorapatite, in high Ca and Na-Ca environments under P-T conditions of 200-1000 MPa and 450-750 °C

NASA Astrophysics Data System (ADS)

Budzyń, Bartosz; Harlov, Daniel E.; Kozub-Budzyń, Gabriela A.; Majka, Jarosław

2017-04-01

The relative stabilities of phases within the two systems monazite-(Ce) - fluorapatite - allanite-(Ce) and xenotime-(Y) - (Y,HREE)-rich fluorapatite - (Y,HREE)-rich epidote have been tested experimentally as a function of pressure and temperature in systems roughly replicating granitic to pelitic composition with high and moderate bulk CaO/Na2O ratios over a wide range of P-T conditions from 200 to 1000 MPa and 450 to 750 °C via four sets of experiments. These included (1) monazite-(Ce), labradorite, sanidine, biotite, muscovite, SiO2, CaF2, and 2 M Ca(OH)2; (2) monazite-(Ce), albite, sanidine, biotite, muscovite, SiO2, CaF2, Na2Si2O5, and H2O; (3) xenotime-(Y), labradorite, sanidine, biotite, muscovite, garnet, SiO2, CaF2, and 2 M Ca(OH)2; and (4) xenotime-(Y), albite, sanidine, biotite, muscovite, garnet, SiO2, CaF2, Na2Si2O5, and H2O. Monazite-(Ce) breakdown was documented in experimental sets (1) and (2). In experimental set (1), the Ca high activity (estimated bulk CaO/Na2O ratio of 13.3) promoted the formation of REE-rich epidote, allanite-(Ce), REE-rich fluorapatite, and fluorcalciobritholite at the expense of monazite-(Ce). In contrast, a bulk CaO/Na2O ratio of 1.0 in runs in set (2) prevented the formation of REE-rich epidote and allanite-(Ce). The reacted monazite-(Ce) was partially replaced by REE-rich fluorapatite-fluorcalciobritholite in all runs, REE-rich steacyite in experiments at 450 °C, 200-1000 MPa, and 550 °C, 200-600 MPa, and minor cheralite in runs at 650-750 °C, 200-1000 MPa. The experimental results support previous natural observations and thermodynamic modeling of phase equilibria, which demonstrate that an increased CaO bulk content expands the stability field of allanite-(Ce) relative to monazite-(Ce) at higher temperatures indicating that the relative stabilities of monazite-(Ce) and allanite-(Ce) depend on the bulk CaO/Na2O ratio. The experiments also provide new insights into the re-equilibration of monazite-(Ce) via fluid-aided coupled dissolution-reprecipitation, which affects the Th-U-Pb system in runs at 450 °C, 200-1000 MPa, and 550 °C, 200-600 MPa. A lack of compositional alteration in the Th, U, and Pb in monazite-(Ce) at 550 °C, 800-1000 MPa, and in experiments at 650-750 °C, 200-1000 MPa indicates the limited influence of fluid-mediated alteration on volume diffusion under high P-T conditions. Experimental sets (3) and (4) resulted in xenotime-(Y) breakdown and partial replacement by (Y,REE)-rich fluorapatite to Y-rich fluorcalciobritholite. Additionally, (Y,HREE)-rich epidote formed at the expense of xenotime-(Y) in three runs with 2 M Ca(OH)2 fluid, at 550 °C, 800 MPa; 650 °C, 800 MPa; and 650 °C, 1000 MPa similar to the experiments involving monazite-(Ce). These results confirm that replacement of xenotime-(Y) by (Y,HREE)-rich epidote is induced by a high Ca bulk content with a high CaO/Na2O ratio. These experiments demonstrate also that the relative stabilities of xenotime-(Y) and (Y,HREE)-rich epidote are strongly controlled by pressure.

76 FR 74777 - National Marine Protected Areas Center External Review

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-01

... through targeted science, information resources, coordination and policy development. An external review..., 1305 East-West Highway, Rm. 11401, Silver Spring, Maryland 20910. FOR FURTHER INFORMATION CONTACT....mpa.gov SUPPLEMENTARY INFORMATION: The MPA Center's external review will encompass program activities...

Bond behavior of reinforcing steel in ultra-high performance concrete.

DOT National Transportation Integrated Search

2014-10-01

Ultra-High Performance Concrete (UHPC) is a relatively new class of advanced cementitious composite : materials, which exhibits high compressive [above 21.7 ksi (150 MPa)] and tensile [above 0.72 ksi (5 MPa)] : strengths. The discrete steel fiber rei...

Development of 780MPa grade gal annealed dual phase steel sheets for automobile

NASA Astrophysics Data System (ADS)

Jiang, Yinghua; Xie, Chunqian; Kuang, Shuang

2018-01-01

As the weight reduction of automotive body and crash safety become much more important factors, in an effort to satisfy these requirements, Shougang has developed 780MPa grade galvannealed dual phase steel sheet. Steel chemistry with low C and low Si was designed for good zinc wettability and spot weldability. And some of elements were added to improve the hole expansibility and work hardening capacity of steel as these effectively refine the microstructure and introduce retained austenite. Newly developed 780MPa grade galvannealed dual phase steels have a high yield strength and a good hole expansibility.

Reference Correlation for the Viscosity of Ammonia from the Triple Point to 725 K and up to 50 MPa

NASA Astrophysics Data System (ADS)

Monogenidou, S. A.; Assael, M. J.; Huber, M. L.

2018-06-01

This paper presents a new wide-ranging correlation for the viscosity of ammonia based on critically evaluated experimental data. The correlation is designed to be used with a recently developed equation of state, and it is valid from the triple point to 725 K at pressures up to 50 MPa. The estimated uncertainty varies depending on the temperature and pressure, from 0.6% to 5%. The correlation behaves in a physically reasonable manner when extrapolated to 100 MPa; however, care should be taken when using the correlation outside of the validated range.

INTERNATIONAL CONFERENCE ON SEMICONDUCTOR INJECTION LASERS SELCO-87: Thermally induced stresses in stripe GaAs/GaAlAs laser diodes

NASA Astrophysics Data System (ADS)

Rimpler, R.; Both, W.

1988-11-01

Heating of the active region of stripe GaAlAs/GaAs double-heterostructure laser diodes by an injection current has a strong influence on the stresses in this region. An increase in the temperature of the region by 10 K can alter a shear stress by 5-10 MPa. In the case of lasers with a large thermal resistance the strong heating of the active region can induce mechanical stresses exceeding technological stresses (10 MPa) or even critical shear stresses for dislocation motion (20 MPa).

Thermophysical properties of Helium-4 from 0.8 to 1500 K with pressures to 2000 MPa

NASA Technical Reports Server (NTRS)

Arp, Vincent D.; Mccarty, Robert D.

1989-01-01

Tabular summary data of the thermophysical properties of fluid helium are given for temperatures from 0.8 to 1500 K, with pressures to 2000 MPa between 75 and 300 K, or to 100 MPa outside of this temperature band. Properties include density, specific heats, enthalpy, entropy, internal energy, sound velocity, expansivity, compressibility, thermal conductivity, and viscosity. The data are calculated from a computer program which is available from the National Institute of Standards and Technology. The computer program is based on carefully fitted state equations for both normal and superfluid helium.

An adaptable toolkit to assess commercial fishery costs and benefits related to marine protected area network design.

PubMed

Daigle, Rémi M; Monaco, Cristián J; Elgin, Ashley K

2015-01-01

Around the world, governments are establishing Marine Protected Area (MPA) networks to meet their commitments to the United Nations Convention on Biological Diversity. MPAs are often used in an effort to conserve biodiversity and manage fisheries stocks. However, their efficacy and effect on fisheries yields remain unclear. We conducted a case-study on the economic impact of different MPA network design strategies on the Atlantic cod ( Gadus morhua ) fisheries in Canada. The open-source R package that we developed to analyze this case study can be customized to conduct similar analyses for other systems. We used a spatially-explicit individual-based model of population growth and dispersal coupled with a fisheries management and harvesting component. We found that MPA networks that both protect the target species' habitat and were spatially optimized to improve population connectivity had the highest net present value (i.e., were most profitable for the fishing industry). These higher profits were achieved primarily by reducing the distance travelled for fishing and reducing the probability of a moratorium event. These findings add to a growing body of knowledge demonstrating the importance of incorporating population connectivity in the MPA planning process, as well as the ability of this R package to explore ecological and economic consequences of alternative MPA network designs.

Functional properties and in vitro trypsin digestibility of red kidney bean (Phaseolus vulgaris L.) protein isolate: Effect of high-pressure treatment.

PubMed

Yin, Shou-Wei; Tang, Chuan-He; Wen, Qi-Biao; Yang, Xiao-Quan; Li, Lin

2008-10-15

The effects of high-pressure (HP) treatment at 200-600MPa, prior to freeze-drying, on some functional properties and in vitro trypsin digestibility of vicilin-rich red kidney bean (Phaseolus vulgaris L.) protein isolate (KPI) were investigated. Surface hydrophobicity and free sulfhydryl (SH) and disulfide bond (SS) contents were also evaluated. HP treatment resulted in gradual unfolding of protein structure, as evidenced by gradual increases in fluorescence strength and SS formation from SH groups, and decrease in denaturation enthalpy change. The protein solubility of KPI was significantly improved at pressures of 400MPa or higher, possibly due to formation of soluble aggregate from insoluble precipitate. HP treatment at 200 and 400MPa significantly increased emulsifying activity index (EAI) and emulsion stability index (ESI); however, EAI was significantly decreased at 600MPa (relative to untreated KPI). The thermal stability of the vicilin component was not affected by HP treatment. Additionally, in vitro trypsin digestibility of KPI was decreased only at a pressure above 200MPa and for long incubation time (e.g., 120min). The data suggest that some physiochemical and functional properties of vicilin-rich kidney proteins can be improved by means of high-pressure treatment. Copyright © 2008 Elsevier Ltd. All rights reserved.

Effect of high pressure on growth and bacteriocin production of Pediococcus acidilactici HA-6111-2

NASA Astrophysics Data System (ADS)

Castro, S. M.; Kolomeytseva, M.; Casquete, R.; Silva, J.; Saraiva, J. A.; Teixeira, P.

2015-10-01

This study was aimed to investigate the effect of high pressure processing (HPP, 200-600 MPa) on the (i) survival of Listeria innocua and Pediococcus acidilactici HA-6111-2; (ii) production of bacteriocin bacHA-6111-2 and (iii) activity of bacteriocin against untreated and pressure-treated L. innocua cells. Inactivation of P. acidilactici was observed for pressures of >300 MPa. However, at this pressure level, L. innocua was more sensitive. Bacteriocin crude extract was pressure stable, with a decrease for pressures of ≥400 MPa. Pressures of ≤200 MPa did not affect bacteriocin production when compared with non-pressure-treated cells, whereas higher pressures caused a 2- to 4-fold decrease on the maximum level of bacteriocin production. Growth curves of P. acidilactici were fitted with the modified Gompertz model. The lag phase period depended on the magnitude of the pressure applied: there was a delay in the exponential phase as pressure increased and, as a consequence, in the beginning of bacteriocin production. Since P. acidilactici HA-6111-2 and its bacteriocin have shown resistance to pressures up to 300-400 MPa, they could be used in combination with HPP in order to improve food safety.

Demethylation and cleavage of dimethylsulfoniopropionate in marine intertidal sediments

USGS Publications Warehouse

Visscher, P.T.; Kiene, R.P.; Taylor, B.F.

1994-01-01

Demethylation and cleavage of dimethylsulfoniopropionate (DMSP) was measured in three different types of,intertidal marine sediments: a cyanobacterial mat, a diatom-covered tidal flat and a carbonate sediment. Consumption rates of added DMSP were highest in cyanobacterial mat slurries (59 ?? mol DMSP l-1 slurry h-1) and lower in slurries from a diatom mat and a carbonate tidal sediment (24 and 9 ??mol DMSP l-1 h-1, respectively). Dimethyl sulfide (DMS) and 3-mercaptopropionate (MPA) were produced simultaneously during DMSP consumption, indicating that cleavage and demethylation occurred at the same time. Viable counts of DMSP-utilizing bacteria revealed a population of 2 x 107 cells cm-3 sediment (90% of these cleaved DMSP to DMS, 10% demethylated DMSP to MPA) in the cyanobacterial mat, 7 x 105 cells cm-3 in the diatom mat (23% cleavers, 77% demethylators), and 9 x 104 cells cm-3 (20% cleavers and 80% demethylators) in the carbonate sediment. In slurries of the diatom mat, the rate of MPA production from added 3-methiolpropionate (MMPA) was 50% of the rate of MPA formation from DMSP. The presence of a large population of demethylating bacteria and the production of MPA from DMSP suggest that the demethylation pathway, in addition to cleavage, contributes significantly to DMSP consumption in coastal sediments.

High pressure processing of fresh meat--is it worth it?

PubMed

Ma, Hanjun; Ledward, D A

2013-12-01

When subjected to high pressures at ambient temperatures, the shelf life of fresh meat is increased; however the meat takes on a cooked appearance as the actomyosin denatures at about 200MPa and the myoglobin denatures and/or co-precipitates with other proteins at about 400MPa. In addition, at pressures of 400MPa and above the unsaturated lipids in the meat become more susceptible to oxidation, probably due to the release of iron from complexes present in meat (haemosiderin and ferritin?) and/or changes in the lipid membrane. Thus, even if legislation allowed it, it is unlikely that many consumers would be prepared to buy such meat. However if pre-rigor meat is subjected to pressures of about 100-150MPa, below those necessary to cause colour changes, it becomes significantly more tender than its untreated counterpart and this may now be a commercially viable process, given the decreasing cost of high pressure rigs. When treated at 100-200MPa while the temperature is raised from ambient to around 60°C post-rigor meat also yields a tender product and this may also be a commercially attractive process to parts of the food industry, for example those involved in catering. Copyright © 2013 Elsevier Ltd. All rights reserved.

Estimation of principal deviatoric stresses imposed on an individual metachert: detailed application of the microboudin palaeopiezometer

NASA Astrophysics Data System (ADS)

Matsumura, T.; Masuda, T.

2017-12-01

The microboudinage structure of columnar mineral grain is an useful marker for the stress imposed on the metamorphic rock. In this presentation, we report a detailed application of the microboudin palaeopiezometer to an individual metachert specimen that includes microboudinaged tourmaline grains. The microboudin palaeostress analysis is conducted to the number of 3621 tourmaline grains divided into every 10° of their long axes on the foliation surface. The analysis revealed that the group of mean orientation ± 15° and perpendicular to the mean orientation ± 15° showed the value of σ1 - σ3 and σ1 - σ2 as 10.2 MPa and 5.3 MPa, respectively. Using both values of σ1 - σ3 and σ1 - σ2, magnitude of principal deviatoric stresses (σ'1, σ'2 and σ'3) are obtained as σ'1 = 5.3 MPa, σ'2 = -0.1 MPa and σ'3 = -5.1 MPa. In this stress state, the stress ratio (σ2 - σ3)/(σ1 - σ3) is 0.48 that indicates typical triaxial compression. As the microboudinage structure is considered to develop immediately before the matrix mineral encountered the cessation of the plastic flow, these values correspond to conditions at ≧ 300 °C on the later stage of the metamorphism.

Temperate marine protected area provides recruitment subsidies to local fisheries.

PubMed

Le Port, A; Montgomery, J C; Smith, A N H; Croucher, A E; McLeod, I M; Lavery, S D

2017-10-25

The utility of marine protected areas (MPAs) as a means of protecting exploited species and conserving biodiversity within MPA boundaries is supported by strong empirical evidence. However, the potential contribution of MPAs to fished populations beyond their boundaries is still highly controversial; empirical measures are scarce and modelling studies have produced a range of predictions, including both positive and negative effects. Using a combination of genetic parentage and relatedness analysis, we measured larval subsidies to local fisheries replenishment for Australasian snapper ( Chrysophrys auratus : Sparidae) from a small (5.2 km 2 ), well-established, temperate, coastal MPA in northern New Zealand. Adult snapper within the MPA contributed an estimated 10.6% (95% CI: 5.5-18.1%) of newly settled juveniles to surrounding areas (approx. 400 km 2 ), with no decreasing trend in contributions up to 40 km away. Biophysical modelling of larval dispersal matched experimental data, showing larvae produced inside the MPA dispersed over a comparable distance. These results demonstrate that temperate MPAs have the potential to provide recruitment subsidies at magnitudes and spatial scales relevant to fisheries management. The validated biophysical model provides a cost-efficient opportunity to generalize these findings to other locations and climate conditions, and potentially informs the design of MPA networks for enhancing fisheries management. © 2017 The Author(s).

Magma storage conditions of historic Plinian eruptions of Volcán de Colima, México

NASA Astrophysics Data System (ADS)

Macias, J.; Arce, J.; Sosa, G.; Gardner, J. E.; Saucedo, R.

2013-12-01

Volcán de Colima has a historical record with major explosive eruptions occurring every ~100 years (1606, 1690, 1818, and 1913) followed by intra-Plinian effusive activity. The 1818 and 1913 Plinian eruptions erupted andesitic magmas (Pl > Opx > Cpx >> Hbl + Fe-Ti oxides + Ap and rare resorbed Ol) with homogeneous bulk compositions (1913; 58.3 × 0.5 wt.% SiO2, 1818; 58.9 × 0.2 wt.% SiO2; Saucedo et al., 2010). Instead, intra-Plinian magmas are devoid of hornblende and have compositions of 59-61 wt. % in silica (Savov et al., 2008). Pre-eruptive temperatures of oxide Fe-Ti pairs in 1818 and 1913 products yielded temperatures of 830×20°C colder than intra-Plinian magmas usually >970°C (Luhr et al., 2002) depending on the mineral phase analyzed. Amphibole in 1818 and 1913 products consists of two populations: a) large xenocrysts, with plag-px-Fe-Ti oxide rims with equilibrium pressures and temperatures of 380 MPa and 950 °C (Ridolfi et al., 2010), and b) microphenocryst with equilibrium pressures and temperatures of 190-280 MPa and 870-910 °C, respectively. Some phenocrysts in the 1818 magma have a high pressure core overgrowth by a low pressure rim. In order to understand the storage conditions of Colima explosive magmas we carried out a set of hydrothermal experiments with a 1818 pumice sample. Experiments were water oversaturated and close to the oxygen fugacity of the NNO buffer. Experiments show that amphibole is stable at pressures greater than 75 MPa at 850°C, and greater than 100 MPa at 925°C. For the same range of temperature, plagioclase is stable at pressures below ~210 MPa and 100 MPa, respectively. Experimental plagioclase and experimental glass were analyzed and compared to those from the natural sample, yielding an approximate storage pressure of 210 MPa. This pressure is confirmed by the chemical equilibrium of microphenocrystic amphibole of the natural sample. Given the nearly equivalent composition of the most recent Plinain magmas is possible to assume the storage pressure of the 1913 Plinian magma. Previous studies found ~6 wt. % of water dissolved in orthopyroxene melt inclusions in the 1913 magma (Luhr, 2006). That water concentration would be dissolved in a melt with the 1913 composition at ~200 MPa (Papale et al., 2006). Equilibrium pressure of 1913 amphiboles, microphenocrysts, and xenocrysts (280-380 MPa), overall, are deeper than those of the 1818 suggesting a deeper 1913 reservoir. Therefore, the 1818 amphiboles with lower pressure rims found in the natural sample could have been inherited from a previous magma (>280 MPa) seated at similar depths than the 1913 reservoir from which were taped. Luhr, J.F., 2002 JVGR 117, 169-194. Ridolfi, F., Renzulli, A., Puerini, M., 2010. Cont Min Petrol 160, 45-66. R. Saucedo, J.L. Macías, J.C. Gavilanes, J.L. Arce, J.C. Komorowski, J.E. Gardner, G. Valdez-Moreno JVGR 191, 149-166 Savov, I.P., Luhr, J.F., Navarro-Ochoa, C., 2008. JVGR 174: 241-256.

Pre-compression volume on flow ripple reduction of a piston pump

NASA Astrophysics Data System (ADS)

Xu, Bing; Song, Yuechao; Yang, Huayong

2013-11-01

Axial piston pump with pre-compression volume(PCV) has lower flow ripple in large scale of operating condition than the traditional one. However, there is lack of precise simulation model of the axial piston pump with PCV, so the parameters of PCV are difficult to be determined. A finite element simulation model for piston pump with PCV is built by considering the piston movement, the fluid characteristic(including fluid compressibility and viscosity) and the leakage flow rate. Then a test of the pump flow ripple called the secondary source method is implemented to validate the simulation model. Thirdly, by comparing results among the simulation results, test results and results from other publications at the same operating condition, the simulation model is validated and used in optimizing the axial piston pump with PCV. According to the pump flow ripples obtained by the simulation model with different PCV parameters, the flow ripple is the smallest when the PCV angle is 13°, the PCV volume is 1.3×10-4 m3 at such operating condition that the pump suction pressure is 2 MPa, the pump delivery pressure 15 MPa, the pump speed 1 000 r/min, the swash plate angle 13°. At the same time, the flow ripple can be reduced when the pump suction pressure is 2 MPa, the pump delivery pressure is 5 MPa,15 MPa, 22 MPa, pump speed is 400 r/min, 1 000 r/min, 1 500 r/min, the swash plate angle is 11°, 13°, 15° and 17°, respectively. The finite element simulation model proposed provides a method for optimizing the PCV structure and guiding for designing a quieter axial piston pump.

Joint European League Against Rheumatism and European Renal Association–European Dialysis and Transplant Association (EULAR/ERA-EDTA) recommendations for the management of adult and paediatric lupus nephritis

PubMed Central

Bertsias, George K; Tektonidou, Maria; Amoura, Zahir; Aringer, Martin; Bajema, Ingeborg; Berden, Jo H M; Boletis, John; Cervera, Ricard; Dörner, Thomas; Doria, Andrea; Ferrario, Franco; Floege, Jürgen; Houssiau, Frederic A; Ioannidis, John P A; Isenberg, David A; Kallenberg, Cees G M; Lightstone, Liz; Marks, Stephen D; Martini, Alberto; Moroni, Gabriela; Neumann, Irmgard; Praga, Manuel; Schneider, Matthias; Starra, Argyre; Tesar, Vladimir; Vasconcelos, Carlos; van Vollenhoven, Ronald F; Zakharova, Helena; Haubitz, Marion; Gordon, Caroline; Jayne, David; Boumpas, Dimitrios T

2012-01-01

Objectives To develop recommendations for the management of adult and paediatric lupus nephritis (LN). Methods The available evidence was systematically reviewed using the PubMed database. A modified Delphi method was used to compile questions, elicit expert opinions and reach consensus. Results Immunosuppressive treatment should be guided by renal biopsy, and aiming for complete renal response (proteinuria <0.5 g/24 h with normal or near-normal renal function). Hydroxychloroquine is recommended for all patients with LN. Because of a more favourable efficacy/toxicity ratio, as initial treatment for patients with class III–IVA or A/C (±V) LN according to the International Society of Nephrology/Renal Pathology Society 2003 classification, mycophenolic acid (MPA) or low-dose intravenous cyclophosphamide (CY) in combination with glucocorticoids is recommended. In patients with adverse clinical or histological features, CY can be prescribed at higher doses, while azathioprine is an alternative for milder cases. For pure class V LN with nephrotic-range proteinuria, MPA in combination with oral glucocorticoids is recommended as initial treatment. In patients improving after initial treatment, subsequent immunosuppression with MPA or azathioprine is recommended for at least 3 years; in such cases, initial treatment with MPA should be followed by MPA. For MPA or CY failures, switching to the other agent, or to rituximab, is the suggested course of action. In anticipation of pregnancy, patients should be switched to appropriate medications without reducing the intensity of treatment. There is no evidence to suggest that management of LN should differ in children versus adults. Conclusions Recommendations for the management of LN were developed using an evidence-based approach followed by expert consensus. PMID:22851469

Final report on supplementary comparison APMP.M.P-S7.TRI in hydraulic gauge pressure from 40 MPa to 200 MPa

NASA Astrophysics Data System (ADS)

Kobata, Tokihiko; Olson, Douglas A.; Eltawil, Alaaeldin A.

2017-01-01

This report describes the results of a supplementary comparison of hydraulic high-pressure standards at three national metrology institutes (NMIs); National Metrology Institute of Japan, AIST (NMIJ/AIST), National Institute of Standards and Technology (NIST), USA and National Institute for Standards (NIS), Egypt, which was carried out at NIST during the period May 2001 to September 2001 within the framework of the Asia-Pacific Metrology Programme (APMP) in order to evaluate their degrees of equivalence at pressures in the range 40 MPa to 200 MPa for gauge mode. The pilot institute was NMIJ/AIST. Three working pressure standards from the institutes, in the form of piston-cylinder assemblies, were used for the comparison. The comparison and calculation methods used are discussed in this report. From the cross-float measurements, the differences between the working pressure standards of each institute were examined through an evaluation of the effective area of each piston-cylinder assembly with its uncertainty. From the comparison results, it was revealed that the values claimed by the participating institutes, NMIJ, NIST, and NIS, agree within the expanded (k = 2) uncertainties. The hydraulic pressure standards in the range 40 MPa to 200 MPa for gauge mode of the three participating NMIs were found to be equivalent within their claimed uncertainties. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Biaxial flexural strength of CAD/CAM ceramics.

PubMed

Buso, L; Oliveira-Júnior, O B; Hiroshi Fujiy, F; Leão Lombardo, G H; Ramalho Sarmento, H; Campos, F; Assunção Souza, R O

2011-06-01

Aim of the study was to evaluate the biaxial flexural strength of ceramics processed using the Cerec inLab system. The hypothesis was that the flexural strength would be influenced by the type of ceramic. Ten samples (ISO 6872) of each ceramic (N.=50/n.=10) were made using Cerec inLab (software Cerec 3D) (Ø:15 mm, thickness: 1.2 mm). Three silica-based ceramics (Vita Mark II [VM], ProCad [PC] and e-max CAD ECAD]) and two yttria-stabilized tetragonal-zirconia-polycrystalline ceramics (Y-TZP) (e-max ZirCad [ZrCAD] and Vita In-Ceram 2000 YZ Cubes [VYZ]) were tested. The samples were finished with wet silicone carbide papers up to 1 200-grit and polished in a polishing machine with diamond paste (3 µm). The samples were then submitted to biaxial flexural strength testing in a universal testing machine (EMIC), 1 mm/min. The data (MPa) were analyzed using the Kruskal-Wallis and Dunn (5%) tests. Scanning electronic microscopy (SEM) was performed on a representative sample from each group. The values (median, mean±sd) obtained for the experimental groups were: VM (101.7, 102.1±13.65 MPa), PC (165.2, 160±34.7 MPa), ECAD (437.2, 416.1±50.1 MPa), ZrCAD (804.2, 800.8±64.47 MPa) and VYZ (792.7, 807±100.7 MPa). The type of ceramic influenced the flexural strength values (P=0.0001). The ceramics ECADa, e-max ZrCADa and VYZa presented similar flexural strength values which were significantly higher than the other groups (PCb and VM IIb), which were similar statistically between them (Dunn's test). The hypothesis was accepted. The polycrystalline ceramics (Y-TZP) should be material chosen for make FPDs because of their higher flexural strength values.

Diabetes mellitus reduces activity of human UDP-glucuronosyltransferase 2B7 in liver and kidney leading to decreased formation of mycophenolic acid acyl-glucuronide metabolite.

PubMed

Dostalek, Miroslav; Court, Michael H; Hazarika, Suwagmani; Akhlaghi, Fatemeh

2011-03-01

Mycophenolic acid (MPA) is an immunosuppressive agent commonly used after organ transplantation. Altered concentrations of MPA metabolites have been reported in diabetic kidney transplant recipients, although the reason for this difference is unknown. We aimed to compare MPA biotransformation and UDP-glucuronosyltransferase (UGT) expression and activity between liver (n = 16) and kidney (n = 8) from diabetic and nondiabetic donors. Glucuronidation of MPA, as well as the expression and probe substrate activity of UGTs primarily responsible for MPA phenol glucuronide (MPAG) formation (UGT1A1 and UGT1A9), and MPA acyl glucuronide (AcMPAG) formation (UGT2B7), was characterized. We have found that both diabetic and nondiabetic human liver microsomes and kidney microsomes formed MPAG with similar efficiency; however, AcMPAG formation was significantly lower in diabetic samples. This finding is supported by markedly lower glucuronidation of the UGT2B7 probe zidovudine, UGT2B7 protein, and UGT2B7 mRNA in diabetic tissues. UGT genetic polymorphism did not explain this difference because UGT2B7*2 or *1c genotype were not associated with altered microsomal UGT2B7 protein levels or AcMPAG formation. Furthermore, mRNA expression and probe activities for UGT1A1 or UGT1A9, both forming MPAG but not AcMPAG, were comparable between diabetic and nondiabetic tissues, suggesting the effect may be specific to UGT2B7-mediated AcMPAG formation. These findings suggest that diabetes mellitus is associated with significantly reduced UGT2B7 mRNA expression, protein level, and enzymatic activity of human liver and kidney, explaining in part the relatively low circulating concentrations of AcMPAG in diabetic patients.

Comparison of the mechanical properties of different skin sites for auricular and nasal reconstruction.

PubMed

Griffin, M F; Leung, B C; Premakumar, Y; Szarko, M; Butler, P E

2017-04-18

Autologous and synthetic nasal and auricular frameworks require skin coverage. The surgeon's decides on the appropriate skin coverage for reconstruction based on colour matching, subcutaneous tissue thickness, expertise and experience. One of the major complications of placing subcutaneous implants is the risk of extrusion (migration through the skin) and infection. However, knowledge of lessening the differential between the soft tissue and the framework can have important implications for extrusion. This study compared the mechanical properties of the skin commonly used as skin sites for the coverage in auricular and nasal reconstruction. Using ten fresh human cadavers, the tensile Young's Modulus of the skin from the forehead, forearm, temporoparietal, post-auricular and submandibular neck was assessed. The relaxation rate and absolute relaxation level was also assessed after 90 min of relaxation. The submandibular skin showed the greatest Young's elastic modulus in tension of all regions (1.28 MPa ±0.06) and forearm showed the lowest (1.03 MPa ±0.06). The forehead demonstrated greater relaxation rates among the different skin regions (7.8 MPa -07  ± 0.1). The forearm showed the lowest rate of relaxation (4.74 MPa -07  ± 0.1). The forearm (0.04 MPa ±0.004) and submandibular neck skin (0.04 MPa ±0.005) showed similar absolute levels of relaxation, which were significantly greater than the other skin regions (p < 0.05). This study provides an understanding into the biomechanical properties of the skin of different sites allowing surgeons to consider this parameter when trying to identify the optimal skin coverage in nasal and auricular reconstruction.

Hydraulic efficiency and safety of vascular and non-vascular components in Pinus pinaster leaves.

PubMed

Charra-Vaskou, Katline; Badel, Eric; Burlett, Régis; Cochard, Hervé; Delzon, Sylvain; Mayr, Stefan

2012-09-01

Leaves, the distal section of the soil-plant-atmosphere continuum, exhibit the lowest water potentials in a plant. In contrast to angiosperm leaves, knowledge of the hydraulic architecture of conifer needles is scant. We investigated the hydraulic efficiency and safety of Pinus pinaster needles, comparing different techniques. The xylem hydraulic conductivity (k(s)) and embolism vulnerability (P(50)) of both needle and stem were measured using the cavitron technique. The conductance and vulnerability of whole needles were measured via rehydration kinetics, and Cryo-SEM and 3D X-ray microtomographic observations were used as reference tools to validate physical measurements. The needle xylem of P. pinaster had lower hydraulic efficiency (k(s) = 2.0 × 10(-4) m(2) MPa(-1) s(-1)) and safety (P(50) = - 1.5 MPa) than stem xylem (k(s) = 7.7 × 10(-4) m(2) MPa(-1) s(-1); P(50) = - 3.6 to - 3.2 MPa). P(50) of whole needles (both extra-vascular and vascular pathways) was - 0.5 MPa, suggesting that non-vascular tissues were more vulnerable than the xylem. During dehydration to - 3.5 MPa, collapse and embolism in xylem tracheids, and gap formation in surrounding tissues were observed. However, a discrepancy in hydraulic and acoustic results appeared compared with visualizations, arguing for greater caution with these techniques when applied to needles. Our results indicate that the most distal parts of the water transport pathway are limiting for hydraulics of P. pinaster. Needle tissues exhibit a low hydraulic efficiency and low hydraulic safety, but may also act to buffer short-term water deficits, thus preventing xylem embolism.

Final report on supplementary comparison APMP.M.P-S6 in gas gauge pressure from 10 MPa to 100 MPa

NASA Astrophysics Data System (ADS)

Kajikawa, Hiroaki; Olson, Douglas A.; Iizumi, Hideaki; Driver, Robert Greg; Kojima, Momoko

2016-01-01

A supplementary comparison of gas high-pressure standards was conducted between the National Metrology Institute of Japan (NMIJ/AIST) and the National Institute of Standards and Technology (NIST), within the framework of the Asia-Pacific Metrology Programme (APMP), in order to determine their degrees of equivalence in the pressure range from 10 MPa to 100 MPa in gauge mode. The pilot institute was NMIJ/AIST. The measurements were carried out from July 2014 to October 2014. Both participating institutes used pressure balances as their pressure standards. Different gases were used for the pressure medium: NMIJ/AIST used Nitrogen, while NIST used Helium. A set of two pressure monitors was used as the transfer standard. The pressure monitors were found sufficiently stable during the measurements. Characteristics of the pressure monitors were evaluated at the pilot institute, and then used for data corrections and uncertainty estimations. In particular, the effect of the gas medium on the pressure monitors was found to be significant, and then all the measurement data were corrected to those with Nitrogen. The degrees of equivalence between the two institutes were evaluated by the relative differences of the participant's results and their associated expanded (k = 2) uncertainties. The gas pressure standards in the range 10 MPa to 100 MPa for gauge mode of the two participating institutes were found to be equivalent within their claimed uncertainties. Main text To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database kcdb.bipm.org/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Effect of Cold Deformation and Annealing on the Microstructure and Tensile Properties of a HfNbTaTiZr Refractory High Entropy Alloy

NASA Astrophysics Data System (ADS)

Senkov, O. N.; Pilchak, A. L.; Semiatin, S. L.

2018-07-01

The microstructure and tensile properties of HfNbTaTiZr after cold working and annealing were investigated. Cold work was introduced by axial compression followed by rolling resulting in a total thickness reduction of 89 pct without any evidence of cracking. The cold-worked material retained a single-phase microstructure and had a room temperature tensile yield stress σ 0.2 = 1438 MPa, peak true stress σ p = 1495 MPa, and true fracture strain ɛ f = 5 pct. Annealing at 800 °C for up to 256 hours resulted in the precipitation of Nb and Ta rich particles with a BCC crystal structure inside a Hf-and-Zr-enriched BCC matrix. The second phase particles nucleated heterogeneously inside deformation bands and slip lines and coarsened during annealing. Analysis of the coarsening behavior suggested that kinetics were controlled by the diffusion of Nb and Ta. In the two-phase material, σ 0.2 and σ p decreased from 1159 to 1071 MPa and from 1174 to 1074 MPa, respectively, with an increase in particle diameter from 0.18 to 0.72 μm, while ɛ f remained between 5 and 8 pct. Full recrystallization and normal grain growth, with the activation energy of 238 kJ/mol and activation volume of 5.3 to 9.6 m3/mol, occurred during annealing above 1000 °C. After heat treatment at this temperature, the alloy was characterized by a single-phase BCC structure with σ 0.2 = 1110 to 1115 MPa, σ p = 1160 to 1195 MPa, and ɛ f = 12 to 19 pct with the maximum values attained after annealing for 1 hour.

Short communication: Inactivation of microbial contaminants in raw milk La Serena cheese by high-pressure treatments.

PubMed

Arqués, J L; Garde, S; Gaya, P; Medina, M; Nuñez, M

2006-03-01

La Serena cheese, a Spanish variety made from Merino ewes' raw milk, has a high pH value, low salt content, and high moisture, conditions that are all favorable for growth and survival of contaminating microorganisms, including pathogens. To improve its microbiological quality and safety, high-pressure treatments at 300 or 400 MPa for 10 min at 10 degrees C were applied to 2 batches of La Serena cheese on d 2 or 50 of ripening. Cheese treated on d 2 at 300 MPa showed viable aerobic counts that were 0.99 log units lower than those for control cheese on d 3 and showed counts of enterococci, coagulase-positive staphylococci, gram-negative bacteria, and coliforms that were 2.05, 0.49, 3.14, and 4.13 log units lower, respectively, than control cheese. For cheese treated on d 2 at 400 MPa, the respective reductions in counts were 2.02, 2.68, 1.45, 3.96, and 5.50 log units. On d 60, viable aerobic counts in cheese treated on d 50 at 300 MPa were 0.50 log units lower than those in control cheese, and counts of enterococci, gram-negative bacteria, and coliforms were 1.37, 2.30, and 4.85 log units lower, respectively. For cheese treated on d 50 at 400 MPa, the respective reductions in counts were 1.29, 1.98, 4.47, and > 5 log units. High-pressure treatments at 300 or 400 MPa on d 2 or 50 reduced significantly the counts of undesirable microorganisms, improving the microbiological quality and safety of La Serena cheese immediately after treatment and at the end of the ripening period.

Effects of femtosecond laser and other surface treatments on the bond strength of metallic and ceramic orthodontic brackets to zirconia

PubMed Central

García-Sanz, Verónica; Bellot-Arcís, Carlos; Mendoza-Yero, Omel; Doñate-Buendía, Carlos; Montero, Javier; Albaladejo, Alberto

2017-01-01

Femtosecond laser has been proposed as a method for conditioning zirconia surfaces to boost bond strength. However, metallic or ceramic bracket bonding to femtosecond laser-treated zirconia surfaces has not been tested. This study compared the effects of four conditioning techniques, including femtosecond laser irradiation, on shear bond strength (SBS) of metallic and ceramic brackets to zirconia.Three hundred zirconia plates were divided into five groups: 1) control (C); 2) sandblasting (APA); 3) silica coating and silane (SC); 4) femtosecond laser (FS); 5) sandblasting followed by femtosecond laser (APA+SC). A thermal imaging camera measured temperature changes in the zirconia during irradiation. Each group was divided into 2 subgroups (metallic vs ceramic brackets). SBS was evaluated using a universal testing machine. The adhesive remnant index (ARI) was registered and surfaces were observed under SEM. Surface treatment and bracket type significantly affected the bracket-zirconia bond strength. SBS was significantly higher (p<0.001) for ceramic brackets in all groups (APA+FS > APA > FS > SC > control) than metallic brackets (APA+FS > FS > SC > APA > control). For metallic brackets, groups SC (5.99 ± 1.86 MPa), FS (6.72 ± 2.30 MPa) and APA+FS (7.22 ± 2.73 MPa) reported significantly higher bond strengths than other groups (p < 0.05). For ceramic brackets, the highest bond strength values were obtained in groups APA (25.01 ± 4.45 MPa), FS (23.18 ± 6.51 MPa) and APA+FS (29.22 ± 8.20 MPa).Femtosecond laser enhances bond strength of ceramic and metallic brackets to zirconia. Ceramic brackets provide significantly stronger adhesion than metallic brackets regardless of the surface treatment method. PMID:29049418

Can Static Habitat Protection Encompass Critical Areas for Highly Mobile Marine Top Predators? Insights from Coastal East Africa.

PubMed

Pérez-Jorge, Sergi; Pereira, Thalia; Corne, Chloe; Wijtten, Zeno; Omar, Mohamed; Katello, Jillo; Kinyua, Mark; Oro, Daniel; Louzao, Maite

2015-01-01

Along the East African coast, marine top predators are facing an increasing number of anthropogenic threats which requires the implementation of effective and urgent conservation measures to protect essential habitats. Understanding the role that habitat features play on the marine top predator' distribution and abundance is a crucial step to evaluate the suitability of an existing Marine Protected Area (MPA), originally designated for the protection of coral reefs. We developed species distribution models (SDM) on the IUCN data deficient Indo-Pacific bottlenose dolphin (Tursiops aduncus) in southern Kenya. We followed a comprehensive ecological modelling approach to study the environmental factors influencing the occurrence and abundance of dolphins while developing SDMs. Through the combination of ensemble prediction maps, we defined recurrent, occasional and unfavourable habitats for the species. Our results showed the influence of dynamic and static predictors on the dolphins' spatial ecology: dolphins may select shallow areas (5-30 m), close to the reefs (< 500 m) and oceanic fronts (< 10 km) and adjacent to the 100 m isobath (< 5 km). We also predicted a significantly higher occurrence and abundance of dolphins within the MPA. Recurrent and occasional habitats were identified on large percentages on the existing MPA (47% and 57% using presence-absence and abundance models respectively). However, the MPA does not adequately encompass all occasional and recurrent areas and within this context, we propose to extend the MPA to incorporate all of them which are likely key habitats for the highly mobile species. The results from this study provide two key conservation and management tools: (i) an integrative habitat modelling approach to predict key marine habitats, and (ii) the first study evaluating the effectiveness of an existing MPA for marine mammals in the Western Indian Ocean.

Synthesis and characterization of a novel N-vinylcaprolactam-containing acrylic acid terpolymer for applications in glass-ionomer dental cements.

PubMed

Moshaverinia, Alireza; Roohpour, Nima; Darr, Jawwad A; Rehman, Ihtesham U

2009-07-01

In this study a novel N-vinylcaprolactam (NVC)-containing copolymer of acrylic-itaconic acid was synthesized, characterized and incorporated into Fuji IX conventional glass-ionomer cement (GIC). Subsequently, the effects of incorporation of synthesized terpolymer on the mechanical properties of GIC were studied. The synthesized terpolymer was characterized using (1)H nuclear magnetic resonance, Fourier transform infrared and Raman spectroscopy. The viscosity and molecular weight of the terpolymer were also measured. The compressive strength (CS), diametral tensile strength (DTS) and biaxial flexural strength (BFS) of the modified GICs were evaluated after 24h and 1week of immersion in distilled water at 37 degrees C. The handling properties (working and setting times) of the resulting modified cements were also evaluated. One-way analysis of variance was used to study the statistical significance of the mechanical strengths and handling properties in comparison to the control group. The results showed that NVC-containing GIC samples exhibited significantly higher (P<0.05) DTS (38.3+/-10.9MPa) and BFS (82.2+/-12.8MPa) in comparison to Fuji IX GIC (DTS=19.6+/-11.4MPa; BFS=41.3+/-10.5MPa). The experimental cement also showed higher but not statistically significant values for CS compared to the control material (CS for NVC-containing sample=303+/-32.8MPa; CS for Fuji XI=236+/-41.5MPa). Novel NVC-containing GIC has been developed in this study, with a 28% increase in CS. The presented GIC is capable of doubling the DTS and BFS in comparison to commercial Fuji IX GIC. The working properties of NVC-containing glass-ionomer formulations are comparable and are acceptable for water-based cements.

Effects of mechanical loading on the degradability and mechanical properties of the nanocalcium-deficient hydroxyapatite–multi(amino acid) copolymer composite membrane tube for guided bone regeneration

PubMed Central

Duan, Hong; Yang, Hongsheng; Xiong, Yan; Zhang, Bin; Ren, Cheng; Min, Li; Zhang, Wenli; Yan, Yonggang; Li, Hong; Pei, Fuxing; Tu, Chongqi

2013-01-01

Background and methods Guided bone regeneration (GBR) is a new treatment for bone defects, and the property of membrane is critical to the success of GBR. This study focuses on a novel membrane tube for GBR, which was prepared by a nanocalcium-deficient hydroxyapatite–multi(amino acid) copolymer (n-CDHA-MAC) composite. The biomechanical strength and degradability of this membrane tube under mechanical loading after immersion in phosphate-buffered solution were investigated to evaluate the effects of mechanical loading on the membrane tube. The membrane-tube group with no mechanical loading and femora bone were used as controls. Results The compressive strength and bending strength of n-CDHA-MAC membrane tubes were 66.4 ± 10.2 MPa and 840.7 ± 12.1 MPa, which were lower than those of the goats’ femoral bones (69.0 ± 5.5 MPa and 900.2 ± 17.3 MPa), but there were no significant (P > 0.05) differences. In the in vitro degradability experiment, all membrane tubes were degradable and showed a surface-erosion degradation model. The PH of solution fluctuated from 7.2 to 7.5. The weight and mechanical strength of loaded tubes decreased more quickly than nonloaded ones, with significant differences (P < 0.05). However, the strength of the loaded group after degradation achieved 20.4 ± 1.2 MPa, which was greater than the maximum mechanical strength of 4.338 MPa based on goat femoral middle stationary state by three-dimensional finite-element analysis. Conclusions n-CDHA-MAC membrane tubes have good biomechanical strength during degradation under mechanical loading. Therefore, this membrane tube is an ideal GBR membrane for critical size defects of long bones in goats for animal experiments. PMID:23946651

Geotechnical Feasibility Analysis of Compressed Air Energy Storage (CAES) in Bedded Salt Formations: a Case Study in Huai'an City, China

NASA Astrophysics Data System (ADS)

Zhang, Guimin; Li, Yinping; Daemen, Jaak J. K.; Yang, Chunhe; Wu, Yu; Zhang, Kai; Chen, Yanlong

2015-09-01

The lower reaches of the Yangtze River is one of the most developed regions in China. It is desirable to build compressed air energy storage (CAES) power plants in this area to ensure the safety, stability, and economic operation of the power network. Geotechnical feasibility analysis was carried out for CAES in impure bedded salt formations in Huai'an City, China, located in this region. First, geological investigation revealed that the salt groups in the Zhangxing Block meet the basic geological conditions for CAES storage, even though the possible unfavorable characteristics of the salt formations include bedding and different percentages of impurities. Second, mechanical tests were carried out to determine the mechanical characteristics of the bedded salt formations. It is encouraging that the samples did not fail even when they had undergone large creep deformation. Finally, numerical simulation was performed to evaluate the stability and volume shrinkage of the CAES under the following conditions: the shape of a single cavern is that of a pear; the width of the pillar is adopted as two times the largest diameter; three regular operating patterns were adopted for two operating caverns (internal pressure 9-10.5 MPa, 10-11.5 MPa, and 11-12.5 MPa), while the other two were kept at high pressure (internal pressure 10.5, 11.5, and 12.5 MPa) as backups; an emergency operating pattern in which two operating caverns were kept at atmospheric pressure (0.1 MPa) for emergency while the backups were under operation (9-10.5 MPa), simulated for 12 months at the beginning of the 5th year. The results of the analysis for the plastic zone, displacement, and volume shrinkage support the feasibility of the construction of an underground CAES power station.

Conservative Decrease in Water Potential in Existing Leaves during New Leaf Expansion in Temperate and Tropical Evergreen Quercus Species

PubMed Central

Saito, Takami; Naiola, B. Paul; Terashima, Ichiro

2007-01-01

Background and Aims This study aimed at clarifying how the water potential gradient (ΔΨ) is maintained in the shoots of evergreen trees with expanding leaves, whose leaf water potentials at the turgor loss point (Ψtlp) are generally high. Materials The water relations were examined in current-year expanding (CEX) and 1-year-old (OLD) leaves on the same shoots in temperate (Osaka, Japan) and tropical (Bogor, Indonesia) areas. A temperate evergreen species, Quercus glauca growing in both sites, was compared with a temperate deciduous species, Q. serrata, in Osaka, and two tropical evergreen species, Q. gemelliflora and Q. subsericea, in Bogor. Key Results (1) In Osaka, the midday leaf water potential (Ψmidday) was slightly higher in OLD (−0·5 MPa) than in CEX leaves (−0·6 MPa), whereas Ψtlp was significantly lower in OLD (−2·9 MPa) than in CEX leaves (−1·0 MPa). In Bogor, Ψmidday was also higher in OLD leaves (−1·0 MPa) despite the low Ψtlp (−1·9 MPa), although stomatal conductance was not always low in OLD leaves. In the branch bearing CEX and OLD leaves, most of the hydraulic resistance (86 %) exists in the current-year branch, leading to differences in water supply between CEX and OLD leaves. The removal of buds just before breaking did not affect the high Ψmidday in OLD leaves after 1 month. Ψmidday in OLD leaves thus appears to be independent of that in CEX leaves. Conclusions The moderate decrease in Ψmidday in OLD leaves would contribute to maintenance of ΔΨ in the shoots during leaf expansion. PMID:17855379

High pressure-induced inactivation of Qbeta coliphage and c2 phage in oysters and in culture media.

PubMed

Smiddy, Mary; Kelly, Alan L; Patterson, Margaret F; Hill, Colin

2006-02-01

High pressure (HP) treatment inactivates bacteria in shellfish, but its effects on viruses in shellfish have not yet been determined, although viral illness is frequently associated with shellfish consumption. The aim of this study was to investigate the baroresistance of two bacteriophage viruses, Qbeta coliphage and c2 phage, in oysters and in culture media. High numbers (>or=10(7) ml(-1) or g(-1)) of both phages were obtained in culture media and in oysters. Samples were HP treated at 200-800 MPa at 20 degrees C for up to 30 min. Little or no inactivation of either phage was observed in oysters or in culture media after treatment at

Correlation of IMPDH1 gene polymorphisms with subclinical acute rejection and mycophenolic acid exposure parameters on day 28 after renal transplantation.

PubMed

Kagaya, Hideaki; Miura, Masatomo; Saito, Mitsuru; Habuchi, Tomonori; Satoh, Shigeru

2010-08-01

The risk of acute rejection in patients with higher exposure to mycophenolic acid (MPA), the active metabolite of mycophenolate mofetil (MMF), might be due to inosine 5'-monophosphate dehydrogenase (IMPDH) polymorphisms. The correlations with subclinical acute rejection, IMPDH1 polymorphisms and MPA exposure on day 28 post-transplantation were investigated in 82 Japanese recipients. Renal transplant recipients were given combination immunosuppressive therapy consisting of tacrolimus and 1.0, 1.5 or 2.0 g/day of MMF in equally divided doses every 12 hr at designated times. There were no significant differences in the incidence of subclinical acute rejection between IMPDH1 rs2278293 or rs2278294 polymorphisms (p = 0.243 and 0.735, respectively). However, in the high MPA night-time exposure range (AUC > 60 microg x h/ml and C(0 )> or = 1.9 microg/ml), there was a significant difference in the incidence of subclinical acute rejection between IMPDH1 rs2278293 A/A, A/G and G/G genotypes (each p = 0.019), but not the IMPDH1 rs2278294 genotype. In the higher daytime MPA exposure range, patients with the IMPDH1 rs2278293 G/G genotype also tended to develop subclinical acute rejection. In patients with the IMPDH rs2278293 A/A genotype, the risk of subclinical acute rejection episode tends to be low and the administration of MMF was effective. The risk of subclinical acute rejection for recipients who cannot adapt in therapeutic drug monitoring (TDM) of MPA seems to be influenced by IMPDH1 rs2278293 polymorphism. The prospective analysis of IMPDH1 rs2278293 polymorphism as well as monitoring of MPA plasma concentration after transplantation might help to improve MMF therapy.

Development and validation of case-finding algorithms for the identification of patients with anti-neutrophil cytoplasmic antibody-associated vasculitis in large healthcare administrative databases.

PubMed

Sreih, Antoine G; Annapureddy, Narender; Springer, Jason; Casey, George; Byram, Kevin; Cruz, Andy; Estephan, Maya; Frangiosa, Vince; George, Michael D; Liu, Mei; Parker, Adam; Sangani, Sapna; Sharim, Rebecca; Merkel, Peter A

2016-12-01

The aim of this study was to develop and validate case-finding algorithms for granulomatosis with polyangiitis (Wegener's, GPA), microscopic polyangiitis (MPA), and eosinophilic GPA (Churg-Strauss, EGPA). Two hundred fifty patients per disease were randomly selected from two large healthcare systems using the International Classification of Diseases version 9 (ICD9) codes for GPA/EGPA (446.4) and MPA (446.0). Sixteen case-finding algorithms were constructed using a combination of ICD9 code, encounter type (inpatient or outpatient), physician specialty, use of immunosuppressive medications, and the anti-neutrophil cytoplasmic antibody type. Algorithms with the highest average positive predictive value (PPV) were validated in a third healthcare system. An algorithm excluding patients with eosinophilia or asthma and including the encounter type and physician specialty had the highest PPV for GPA (92.4%). An algorithm including patients with eosinophilia and asthma and the physician specialty had the highest PPV for EGPA (100%). An algorithm including patients with one of the diagnoses (alveolar hemorrhage, interstitial lung disease, glomerulonephritis, and acute or chronic kidney disease), encounter type, physician specialty, and immunosuppressive medications had the highest PPV for MPA (76.2%). When validated in a third healthcare system, these algorithms had high PPV (85.9% for GPA, 85.7% for EGPA, and 61.5% for MPA). Adding the anti-neutrophil cytoplasmic antibody type increased the PPV to 94.4%, 100%, and 81.2% for GPA, EGPA, and MPA, respectively. Case-finding algorithms accurately identify patients with GPA, EGPA, and MPA in administrative databases. These algorithms can be used to assemble population-based cohorts and facilitate future research in epidemiology, drug safety, and comparative effectiveness. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Development and Validation of Case-Finding Algorithms for the Identification of Patients with ANCA-Associated Vasculitis in Large Healthcare Administrative Databases

PubMed Central

Sreih, Antoine G.; Annapureddy, Narender; Springer, Jason; Casey, George; Byram, Kevin; Cruz, Andy; Estephan, Maya; Frangiosa, Vince; George, Michael D.; Liu, Mei; Parker, Adam; Sangani, Sapna; Sharim, Rebecca; Merkel, Peter A.

2016-01-01

Purpose To develop and validate case-finding algorithms for granulomatosis with polyangiitis (Wegener’s, GPA), microscopic polyangiitis (MPA), and eosinophilic granulomatosis with polyangiitis (Churg-Strauss, EGPA). Methods 250 patients per disease were randomly selected from 2 large healthcare systems using the International Classification of Diseases version 9 (ICD9) codes for GPA/EGPA (446.4) and MPA (446.0). 16 case-finding algorithms were constructed using a combination of ICD9 code, encounter type (inpatient or outpatient), physician specialty, use of immunosuppressive medications, and the anti-neutrophil cytoplasmic antibody (ANCA) type. Algorithms with the highest average positive predictive value (PPV) were validated in a third healthcare system. Results An algorithm excluding patients with eosinophilia or asthma and including the encounter type and physician specialty had the highest PPV for GPA (92.4%). An algorithm including patients with eosinophilia and asthma and the physician specialty had the highest PPV for EGPA (100%). An algorithm including patients with one of the following diagnoses: alveolar hemorrhage, interstitial lung disease, glomerulonephritis, acute or chronic kidney disease, the encounter type, physician specialty, and immunosuppressive medications had the highest PPV for MPA (76.2%). When validated in a third healthcare system, these algorithms had high PPV (85.9% for GPA, 85.7% for EGPA, and 61.5% for MPA). Adding the ANCA type increased the PPV to 94.4%, 100%, and 81.2% for GPA, EGPA, and MPA respectively. Conclusion Case-finding algorithms accurately identify patients with GPA, EGPA, and MPA in administrative databases. These algorithms can be used to assemble population-based cohorts and facilitate future research in epidemiology, drug safety, and comparative effectiveness. PMID:27804171

The effect of subpressure on the bond strength of resin to zirconia ceramic.

PubMed

Li, Yong-Mei; Zhuge, Rui-Shen; Zhang, Zu-Tai; Tian, Yue-Ming; Ding, Ning

2017-01-01

This study was conducted to investigate the effect of subpressure on the bond strength of resin to zirconia ceramic. The subpressure would create a pressure gradient which could clean out the bubbles in the adhesives or bonding interface. Twenty-eight pre-sintered zirconia discs were fabricated. Half of them were polished (group P, n = 14), and the rest were sandblasted (group S, n = 14). After sintered,the surface roughness of the zirconia discs was measured. Then, they were randomly divided into two subgroups (n = 7). The groups were named as follows: PC: P + no additional treatments; PP: P + 0.04 MPa after application of adhesives; SC: S + no additional treatments; and SP: S + 0.04 MPa after application of adhesives. Resin columns were bonded to the zirconia specimens to determine shear bond strength (SBS). The bonding interfaces were observed and the fracture modes were evaluated. Statistical analysis was performed on all data. The surface roughness of group S was significantly higher than that of group P (P<0.05). The SBS values were PC = 13.48 ± 0.7 MPa, PP = 15.22 ± 0.8 MPa, SC = 17.23 ± 0.7 MPa and SP = 21.68 ± 1.4 MPa. There were significant differences among the groups (P<0.05). Scanning electron microscopy (SEM) results showed that the adhesives of group SP and PP were closer and denser to the zirconia ceramic than that of group PC and SC. The proportion of the mixed fracture mode significantly increased after adding subpressure (P< 0.05). Subpressure can improve the shear bond strength of resin to zirconia ceramics and increase micro-infiltration between the adhesives and the zirconia ceramics, especially on the rough surfaces.

The 371 deg C mechanical properties of graphite/polyimide composites

NASA Technical Reports Server (NTRS)

Delvigs, P.

1985-01-01

A series of condensation polyimides based on pyromellitic dianhydride is synthesized and evaluated for potential application at 371 C. Several three-and four-ring benzenoid diamine systems containing oxygen bridging groups are investigated. Thermomechanical analysis of neat resin specimens indicate that the polyimide prepared from the dimethyl ester of pyrometallitic acid (PMDE) and 2,2-bis4-(4'-aminophenoxy) phenyl]-1,1,1,3,3,3- hexafluoropropane (BDAF) is the only resin system which has a glass transition temperature (Tg) above 371 C. The Tg of the PMDE/BDAF polyimide is found to be 390 C after a postcure air at 371 C for 24 hr. Unidirectional composites are fabricated from the PMDE/BDAF system and unsized Celion 6000 graphite fibers. Final cure temperatures in the range of 371 to 427 C with an applied pressure of 10.34 to 13.78 MPa are investigated. The void content of the composites ranges from 4.6 to 8.6 percent. Composites cured at 399 C under a pressure of 10.34 MPa and postcured in air at 371 C for 24 hr exhibit the highest 371 C interlaminar shear strength (ILSS, 40.7 MPa) and flexural strength (758 MPa). The thermo-oxidative stability of the composites is determined by subjecting specimens to isothermal exposure at 371 C in air at atmospheric pressure, as well as a pressure of 0.52 MPa. Specimens exposed at atmospheric pressure exhibit a weight loss of 12 percent after 200 hr of exposure and 88 percent retention of its original 371 C ILSS. In contrast, the specimens exposed at 0.52 MPa pressure exhibit a comparable weight loss after only 72 hr, and a 71 percent retention of its original 371 C ILSS.

Cognitive function variations in postmenopausal women treated with continuous, combined HRT or tibolone. A comparison.

PubMed

Pan, Hsien-An; Wang, Shan-Tair; Pai, Ming-Chyi; Chen, Chih-Hung; Wu, Meng-Hsing; Huang, Ko-En

2003-05-01

To compare cognitive function in postmenopausal women receiving continuous hormone replacement therapy and those receiving tibolone. This was a 6-month, prospective, single-blind, single center, randomized study. A total of 50 healthy, postmenopausal women were enrolled. In the end, 40 women completed the 6-month follow-up. One group (23 subjects) received conjugated equine estrogens (CEE), 0.625 mg/d, and medroxyprogesterone acetate (MPA), 5 mg/d. The other group (17 subjects) received tibolone, 2.5 mg/d. Their serum estradiol levels and Cognitive Abilities Screening Instrument (CASI) and Mini-Mental State Examination (MMSE) scores were obtained before starting and after 3 and 6 months of treatment. There was a significant increase in the serum estradiol level in the CEE + MPA group, especially after 3 months of treatment, but there was no increase in the estradiol level in the tibolone group. The CASI and MMSE scores of the CEE + MPA group and the tibolone group after 3 and 6 months of treatment showed no significant difference between the two groups apart from the MMSE at the 3-month follow-up. We saw an increasing trend in CASI and MMSE scores after treatment in both groups; however, the increases were not statistically significant. The rate of increase of both CASI and MMSE scores in the CEE + MPA group was greater than in the tibolone group, though the difference was not significant. This preliminary study demonstrated that both CEE + MPA and tibolone can preserve cognitive function and may be able to prevent cognitive decline in postmenopausal women during short-term treatment. Our results also show that continuous, combined CEE + MPA seems to be marginally more effective than tibolone in improving cognitive processes; however, long-term study is needed to follow-up such effect.

Dicalcium phosphate (CaHPO4·2H2O) precipitation through ortho- or meta-phosphoric acid-etching: effects on the durability and nanoleakage/ultra-morphology of resin-dentine interfaces.

PubMed

Feitosa, Victor Pinheiro; Bazzocchi, Maria Giulia; Putignano, Angelo; Orsini, Giovanna; Luzi, Arlinda Luzi; Sinhoreti, Mário Alexandre Coelho; Watson, Timothy F; Sauro, Salvatore

2013-11-01

To compare the effects of two etching procedures using meta-phosphoric (MPA) or ortho-phosphoric acid (OPA) on dentine demineralisation, resin-dentine bonds durability and interface nanoleakage/ultra-morphology. Middle-dentine specimens were etched using 37% OPA (15s) or 40% MPA (60s) and submitted to infrared spectroscopy (FTIR) or ultra-morphology dye-assisted (calcium-staining) confocal microscopy (Ca-CLSM). A three-step etch-and-rinse adhesive was formulated, applied onto dentine and light-cured for 30s before composite build-up. After 24h, the dentine-bonded specimens were cut into 1mm(2) beams; half were immediately submitted to microtensile bond strength (μTBS) and half stored in DW for six months. The μTBS results were analysed with repeated-measures ANOVA and Tukey's test (p<0.05). Further teeth were bonded and prepared for interface nanoleakage/ultra-morphology confocal evaluation. FTIR and Ca-CLSM analyses showed dicalcium phosphate dihydrate (Brushite) precipitation in MPA-etched dentine and on the bottom (front of demineralisation) of the OPA-etched dentine. Statistical analysis showed similar μTBS for both etching procedures after 24h. The μTBS of specimens in OPA-group dropped significantly (p<0.05) after six month; the specimens in the MPA group showed no statistically difference (p>0.05). CLSM depicted no evident sign of nanoleakage within the resin-dentine interface of the MPA-treated specimens, while the specimens in OPA-group presented intense nanoleakage and interface degradation. The use of MPA (60s) as an alternative dentine conditioning agent in etch-and-rinse bonding procedures may be a suitable strategy to create more durable resin-dentine bonds. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mycophenolic acid attenuates tumor necrosis factor-alpha-induced endothelin-1 production in human aortic endothelial cells.

PubMed

Yang, Won Seok; Lee, Joo Mi; Han, Nam Jeong; Kim, Yoon Ji; Chang, Jai Won; Park, Su-Kil

2010-07-01

Atherosclerotic cardiovascular disease is the major cause of morbidity and mortality in solid organ transplant recipients. Endothelin-1 (ET-1) is implicated in the pathogenesis of atherosclerosis and is one of the potential therapeutic targets. This study was conducted to evaluate the effect of mycophenolic acid (MPA), an immunosuppressant for the transplant recipients, on tumor necrosis factor-alpha (TNF-alpha)-induced ET-1 production in aortic endothelial cells. In cultured human aortic endothelial cells, TNF-alpha increased ET-1 through AP-1 and NF-kappaB, whereas MPA attenuated it by reducing both AP-1 and NF-kappaB DNA-binding activities. TNF-alpha increased ET-1 via c-Jun NH2-terminal kinase (JNK) and p38 mitogen-activated protein kinase (MAPK), but not extracellular signal-regulated kinase. N-acetylcysteine that downregulated TNF-alpha-induced reactive oxygen species (ROS) inhibited JNK activation, but not p38 MAPK. N-acetylcysteine, SP600125 (JNK inhibitor) and SB203580 (p38 MAPK inhibitor) attenuated TNF-alpha-induced DNA-binding activities of both AP-1 and NF-kappaB. MPA inhibited JNK and p38 MAPK activations as well as ROS generation. N-acetylcysteine, SP600125, SB203580 and MPA had no effect on either TNF-alpha-induced IkappaBalpha degradation or p65 nuclear translocation, but attenuated p65 Ser276 phosphorylation. MPA attenuated TNF-alpha-induced ET-1 production through inhibitions of ROS-dependent JNK and ROS-independent p38 MAPK that regulated NF-kappaB as well as AP-1. These findings suggest that MPA could have an effect of amelioration of atherosclerosis. Copyright (c) 2010 Elsevier Ireland Ltd. All rights reserved.

Shear bond strength of orthodontic brackets bonded with different self-etching adhesives.

PubMed

Scougall Vilchis, Rogelio José; Yamamoto, Seigo; Kitai, Noriyuki; Yamamoto, Kohji

2009-09-01

The purpose of this study was to compare the shear bond strength (SBS) of orthodontic brackets bonded with 4 self-etching adhesives. A total of 175 extracted premolars were randomly divided into 5 groups (n = 35). Group I was the control, in which the enamel was etched with 37% phosphoric acid, and stainless steel brackets were bonded with Transbond XT (3M Unitek, Monrovia, Calif). In the remaining 4 groups, the enamel was conditioned with the following self-etching primers and adhesives: group II, Transbond Plus and Transbond XT (3M Unitek); group III, Clearfil Mega Bond FA and Kurasper F (Kuraray Medical, Tokyo, Japan); group IV, Primers A and B, and BeautyOrtho Bond (Shofu, Kyoto, Japan); and group V, AdheSE and Heliosit Orthodontic (Ivoclar Vivadent AG, Liechtenstein). The teeth were stored in distilled water at 37 degrees C for 24 hours and debonded with a universal testing machine. The adhesive remnant index (ARI) including enamel fracture score was also evaluated. Additionally, the conditioned enamel surfaces were observed under a scanning electron microscope. The SBS values of groups I (19.0 +/- 6.7 MPa) and II (16.6 +/- 7.3 MPa) were significantly higher than those of groups III (11.0 +/- 3.9 MPa), IV (10.1 +/- 3.7 MPa), and V (11.8 +/- 3.5 MPa). Fluoride-releasing adhesives (Kurasper F and BeautyOrtho Bond) showed clinically acceptable SBS values. Significant differences were found in the ARI and enamel fracture scores between groups I and II. The 4 self-etching adhesives yielded SBS values higher than the bond strength (5.9 to 7.8 MPa) suggested for routine clinical treatment, indicating that orthodontic brackets can be successfully bonded with any of these self-etching adhesives.

[The durability of three self-etch adhesives bonded to dentin].

PubMed

Tian, Fu-Cong; Wang, Xiao-Yan; Gao, Xue-Jun

2013-04-01

To investigate the durability of self-etch adhesives bonded to dentin in vitro. Forty-two extracted human molars were selected and occlusal dentin surfaces were exposed. The teeth were randomly distributed into three groups based on adhesives applied. The one-step self-etch adhesive B(Adper Prompt) and C(G-Bond) and two-step self-etch adhesive A (Clearfil SE bond) were used. After application of the adhesives to the dentin surfaces, composite crowns were built up, after 24 h water storage, the teeth were sectioned longitudinally into sticks (1.0 mm×1.0 mm bonding area) for microtensile testing or slabs (1 mm thick) for scanning electron microscopec (SEM) observation. Bonding strength (mTBS) and nano-leakage were evaluated immediately after cutting or after 6 months in water. The mTBS was analyzed using one-way ANOVA (SPSS 13.0). The nanoleakage was observed by SEM with a backscattered electron detector. Both adhesives and water storage time affected the mTBS. All adhesives showed decreased bond strength after six-month water aging [A dropped from (40.60 ± 5.76) MPa to (36.04 ± 3.15) MPa; B dropped from (19.06 ± 1.50) MPa to (11.19 ± 1.97) MPa; C dropped from (17.75 ± 1.10) MPa to (9.14 ± 1.15) MPa] (P < 0.05). B and C showed lower mTBS than A after aging (P < 0.05). Compared to A, nanoleakage was more obvious after aging for B and C. All self-etch adhesives tested were probably influenced by water aging, however, the two-step adhesive showed better durability than the one-step adhesives.

[Influence of thermalcycling on bonding durability of self-etch adhesives with dentin].

PubMed

Tian, Fu-cong; Wang, Xiao-yan; Gao, Xue-jun

2014-04-18

To investigate influence of thermalcycling on the bonding durability of two one-step products [Adper Prompt (AP) and G-bond (GB)] and one two-step self-etching adhesive [Clearfil SE bond (SE)] with dentin in vitro. Forty-two extracted human molars were selected. The superficial dentin was exposed by grinding off the enamel. The teeth were randomly distributed into six groups with varied bonding protocols. The adhesives were applied to the dentin surface. Composite crowns were built up, then the samples were cut longitudinally into sticks with 1.0 mm×1.0 mm bonding area [for microtensile bond strength (MTBS) testing] or 1.0 mm thick slabs (for nanoleakage observation). Bonding performance was evaluated with or without thermalcyling. For the MTBS testing, the strength values were statistically analysed using One-Way ANOVA. Four slabs in each group were observed for nanoleakage by SEM with a backscattered electron detector. Thermalcycling procedures affected MTBS. In the two one-step groups, the MTBS decreased significantly (P<0.05) after thermalcycling [AP group from (19.06±1.50) MPa to (12.62±2.10) MPa; GB group from (17.75±1.10) MPa to (6.24±0.42)MPa]. But in SE groups, MTBS did not significantly affect [(45.80±2.97) MPa compared with(40.60±5.76) MPa]. As a whole, one-step self-etching adhesives showed lower MTBS than two-step bonding system after aging.For AP and GB, continuous nanoleakage appearance was notable and more obvious than for SE. Thermalcycling can affect the bonding performance of self-etch adhesives including decrease of bond strength and nanoleakage pattern. one-step self-etch adhesives showed more obvious change compared with their two-step counterparts.

The variation of cancellous bones at lumbar vertebra, femoral neck, mandibular angle and rib in ovariectomized sheep.

PubMed

Zhang, Yongqiang; Li, Yongfeng; Gao, Qi; Shao, Bo; Xiao, Jianrui; Zhou, Hong; Niu, Qiang; Shen, Mingming; Liu, Baolin; Hu, Kaijin; Kong, Liang

2014-07-01

This study aimed to compare the variation of cancellous bones at four skeletal sites: lumbar vertebra, femoral neck, mandibular angle and rib in ovariectomized sheep. Sixteen adult sheep were randomly divided into two groups: eight sheep were ovariectomized served as experimental group; the other eight untreated sheep were served as control group. Bone mineral density was assessed by dual-energy X-ray absorptiometry on lumbar vertebrae at baseline and twelve months after ovariectomy. After 12 months, lumbar vertebrae L3 and L4, femoral necks, mandibular angles and the fourth ribs were harvested for micro-CT scanning, histological analysis and biomechanical test. The results showed that bone mineral density of lumbar vertebra decreased significantly in twelfth month (p<0.05). The results of micro-CT showed that the bone volume/total volume decreased by 45.6%, 36.1% 21.3% and 18.7% in lumbar vertebrae, femoral necks, mandibular angles and ribs in experimental group (p<0.05) respectively. The trabecular number showed the same downtrend (p<0.05). Histological analysis showed trabecular area/tissue area decreased by 32.1%, 23.2% and 20.7% in lumbar vertebrae, femoral necks and mandibular angles respectively (p<0.05), but no significant difference in ribs. Specimens elastic modulus from lumbar vertebra, femoral neck and mandibular angle were 952±76MPa (628±70MPa), 961±173MPa (610±72MPa) and 595±60MPa (444±31MPa) in control group (experimental group) respectively. These datum indicated that the sensibility of cancellous bones to oestrogen deficiency in ovariectomized sheep was site-specific on a pattern as follows: lumbar vertebra, femoral neck, mandibular angle and rib. Copyright © 2014 Elsevier Ltd. All rights reserved.

Microstructural and mechanical characterization of CO{sub 2} laser and gas tungsten arc welds of an Al-Li-Cu alloy 2195

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hou, K.H.; Baeslack, W.A. III; Szabo, A.

1994-12-31

Lithium-containing aluminum alloys offer an attractive combination of low density and high strength and stiffness and have been the focus of vigorous research for their promising aerospace applications. To achieve the full potential advantages in using these alloys, the integrity of welded joints, both n the fusion zone and the heat-affected zone, must be ensured. In the present study, Weldalite{sup TM} 049 (designated as alloy 2195) with nominal composition of Al-1.0Li-4.0Cu-0.4Mg0.4Ag-0.14Zr (wt%) was welded autogenously using the gas tungsten-arc (GTA) and CO{sub 2} laser beam (LB) welding processes. The average ultimate tensile strengths for as-welded, 160{degrees}C/16 h-aged, and 190{degrees}C/16 h-agedmore » GTA welds were 296.4 MPa, 304.6 MPa, and 336.8 MPa, and corresponded to joint efficiencies of 61.4%, 48.1% and 56.0%, respectively. Porosity was found occasionally in the laser welds and slightly affected the performance of the aluminum weldments. For laser welds, average ultimate tensile strengths and corresponding joint efficiencies for a-welded, 160{degrees}C/16 h-aged, and 190{degrees}C/16 h-aged weldments were 293.2 MPa (60.8%) 305.9 MPa (48.3%), and 331.0 MPa (55.0%), respectively. Scanning electron fractography revealed that failure of the GTA and LB tensile specimens occurred either within the weld metal or along the fusion boundary. The latter was related to the existence of an equiaxed band along the fusion boundary.« less

The applicability of PEEK-based abutment screws.

PubMed

Schwitalla, Andreas Dominik; Abou-Emara, Mohamed; Zimmermann, Tycho; Spintig, Tobias; Beuer, Florian; Lackmann, Justus; Müller, Wolf-Dieter

2016-10-01

The high-performance polymer PEEK (poly-ether-ether-ketone) is more and more being used in the field of dentistry, mainly for removable and fixed prostheses. In cases of screw-retained implant-supported reconstructions of PEEK, an abutment screw made of PEEK might be advantageous over a conventional metal screw due to its similar elasticity. Also in case of abutment screw fracture, a screw of PEEK could be removed more easily. M1.6-abutment screws of four different PEEK compounds were subjected to tensile tests to set their maximum tensile strengths in relation to an equivalent stress of 186MPa, which is aused by a tightening torque of 15Ncm. Two screw types were manufactured via injection molding and contained 15% short carbon fibers (sCF-15) and 40% (sCF-40), respectively. Two screw types were manufactured via milling and contained 20% TiO2 powder (TiO2-20) and >50% parallel orientated, continuous carbon fibers (cCF-50). A conventional abutments screw of Ti6Al4V (Ti; CAMLOG(®) abutment screw, CAMLOG, Wimsheim, Germany) served as control. The maximum tensile strength was 76.08±5.50MPa for TiO2-20, 152.67±15.83MPa for sCF-15, 157.29±20.11MPa for sCF-40 and 191.69±36.33MPa for cCF-50. The maximum tensile strength of the Ti-screws amounted 1196.29±21.4MPa. The results of the TiO2-20 and the Ti screws were significantly different from the results of the other samples, respectively. For the manufacturing of PEEK abutment screws, PEEK reinforced by >50% continuous carbon fibers would be the material of choice. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biophysical constraints on leaf expansion in a tall conifer.

PubMed

Meinzer, Frederick C; Bond, Barbara J; Karanian, Jennifer A

2008-02-01

The physiological mechanisms responsible for reduced extension growth as trees increase in height remain elusive. We evaluated biophysical constraints on leaf expansion in old-growth Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) trees. Needle elongation rates, plastic and elastic extensibility, bulk leaf water (Psi(L)) and osmotic (Psi(pi)) potential, bulk tissue yield threshold and final needle length were characterized along a height gradient in crowns of > 50-m-tall trees during the period between bud break and full expansion (May to June). Although needle length decreased with increasing height, there was no height-related trend in leaf plastic extensibility, which was highest immediately after bud break (2.9%) and declined rapidly to a stable minimum value (0.3%) over a 3-week period during which leaf expansion was completed. There was a significant positive linear relationship between needle elongation rates and plastic extensibility. Yield thresholds were consistently lower at the upper and middle crown sampling heights. The mean yield threshold across all sampling heights was 0.12 +/- 0.03 MPa on June 8, rising to 0.34 +/- 0.03 MPa on June 15 and 0.45 +/- 0.05 MPa on June 24. Bulk leaf Psi(pi) decreased linearly with increasing height at a rate of 0.004 MPa m(-1) during the period of most rapid needle elongation, but the vertical osmotic gradient was not sufficient to fully compensate for the 0.015 MPa m(-1) vertical gradient in Psi(L), implying that bulk leaf turgor declined at a rate of about 0.011 MPa m(-1) increase in height. Although height-dependent reductions in turgor appeared to constrain leaf expansion, it is possible that the impact of reduced turgor was mitigated by delayed phenological development with increasing height, which resulted in an increase with height in the temperature during leaf expansion.

Mechanically-competent and cytocompatible polycaprolactone-borophosphosilicate hybrid biomaterials.

PubMed

Mondal, Dibakar; Dixon, S Jeffrey; Mequanint, Kibret; Rizkalla, Amin S

2017-11-01

Organic-inorganic class II hybrid materials have domain sizes at the molecular level and chemical bonding between the organic and inorganic phases. We have previously reported the synthesis of class II hybrid biomaterials from alkoxysilane-functionalized polycaprolactone (PCL) and borophosphosilicate (B 2 O 3 -P 2 O 5 -SiO 2 ) glass (BPSG) through a non-aqueous sol-gel process. In the present study, the mechanical properties and degradability of these PCL/BPSG hybrid biomaterials were studied and compared to those of their conventional composite counterparts. The compressive strength, modulus and toughness of the hybrid biomaterials were significantly greater compared to the conventional composites, likely due to the covalent bonding between the organic and inorganic phases. A hybrid biomaterial (50wt% PCL and 50wt% BPSG) exhibited compressive strength, modulus and toughness values of 32.2 ± 3.5MPa, 573 ± 85MPa and 1.54 ± 0.03MPa, respectively; whereas the values for composite of similar composition were 18.8 ± 1.6MPa, 275 ± 28MPa and 0.76 ± 0.03MPa, respectively. Degradation in phosphate-buffered saline was slower for hybrid biomaterials compared to their composite counterparts. Thus, these hybrid materials possess superior mechanical properties and more controlled degradation characteristics compared to their corresponding conventional composites. To assess in vitro cytocompatibility, MC3T3-E1 pre-osteoblastic cells were seeded onto the surfaces of hybrid biomaterials and polycaprolactone (control). Compared to polycaprolactone, cells on the hybrid material displayed enhanced spreading, focal adhesion formation, and cell number, consistent with excellent cytocompatibility. Thus, based on their mechanical properties, degradability and cytocompatibility, these novel biomaterials have potential for use as scaffolds in bone tissue engineering and related applications. Copyright © 2017. Published by Elsevier Ltd.

Macro Pixel ASIC (MPA): the readout ASIC for the pixel-strip (PS) module of the CMS outer tracker at HL-LHC

NASA Astrophysics Data System (ADS)

Ceresa, D.; Marchioro, A.; Kloukinas, K.; Kaplon, J.; Bialas, W.; Re, V.; Traversi, G.; Gaioni, L.; Ratti, L.

2014-11-01

The CMS tracker at HL-LHC is required to provide prompt information on particles with high transverse momentum to the central Level 1 trigger. For this purpose, the innermost part of the outer tracker is based on a combination of a pixelated sensor with a short strip sensor, the so-called Pixel-Strip module (PS). The readout of these sensors is carried out by distinct ASICs, the Strip Sensor ASIC (SSA), for the strip layer, and the Macro Pixel ASIC (MPA) for the pixel layer. The processing of the data directly on the front-end module represents a design challenge due to the large data volume (30720 pixels and 1920 strips per module) and the limited power budget. This is the reason why several studies have been carried out to find the best compromise between ASICs performance and power consumption. This paper describes the current status of the MPA ASIC development where the logic for generating prompt information on particles with high transverse momentum is implemented. An overview of the readout method is presented with particular attention on the cluster reduction, position encoding and momentum discrimination logic. Concerning the architectural studies, a software test bench capable of reading physics Monte-Carlo generated events has been developed and used to validate the MPA design and to evaluate the MPA performance. The MPA-Light is scheduled to be submitted for fabrication this year and will include the full analog functions and a part of the digital logic of the final version in order to qualify the chosen VLSI technology for the analog front-end, the module assembly and the low voltage digital supply.

The effect of a ceramic coating on the cpTi-porcelain bond strength.

PubMed

Papadopoulos, Triantafillos D; Spyropoulos, Konstantin D

2009-02-01

To investigate the bond strength between cpTi and low fusing porcelains after different treatments. 72 patterns were covered with a ceramic coating and invested with phosphate-bonded material (group A), another 72 were invested with magnesia material (group B) and all cast with cpTi. 31 solid castings were selected from each group. The castings of group B were ground and sandblasted, while the castings of group A were only sandblasted. Aluminum content of the metal surface was determined by EDS and castings were submitted to a 3-point bending test to determine the modulus of elasticity (E). The porcelains Duceratin Plus, Noritake Ti22 and Triceram were applied respectively and specimens were submitted to a 3-point bending test. The fracture mode and the remaining porcelain were determined by optical microscopy and SEM/EDS. Bond strength and fracture mode were calculated by two-way ANOVA. The E of groups A and B was 98.3 GPa and 98.6 GPa respectively. The bond strength was 26+/-3 MPa (Duceratin Plus), 28+/-3 MPa (Noritake Ti22), 27+/-2 MPa (Triceram) for group A and 24+/-1 MPa, 29+/-2 MPa, 27+/-1 MPa for group B respectively. No significant differences were found for the same porcelain between the two groups (p<0.05). A significant difference was found between Duceratin Plus and Noritake Ti22, for group B (p<0.05). The mode of failure was mainly adhesive for all specimens. A significant reduction in aluminum was recorded in all subgroups. The special coating of patterns makes the Ti casting procedure inexpensive, without reducing the metal-ceramic bond strength.

Effects of femtosecond laser and other surface treatments on the bond strength of metallic and ceramic orthodontic brackets to zirconia.

PubMed

García-Sanz, Verónica; Paredes-Gallardo, Vanessa; Bellot-Arcís, Carlos; Mendoza-Yero, Omel; Doñate-Buendía, Carlos; Montero, Javier; Albaladejo, Alberto

2017-01-01

Femtosecond laser has been proposed as a method for conditioning zirconia surfaces to boost bond strength. However, metallic or ceramic bracket bonding to femtosecond laser-treated zirconia surfaces has not been tested. This study compared the effects of four conditioning techniques, including femtosecond laser irradiation, on shear bond strength (SBS) of metallic and ceramic brackets to zirconia.Three hundred zirconia plates were divided into five groups: 1) control (C); 2) sandblasting (APA); 3) silica coating and silane (SC); 4) femtosecond laser (FS); 5) sandblasting followed by femtosecond laser (APA+SC). A thermal imaging camera measured temperature changes in the zirconia during irradiation. Each group was divided into 2 subgroups (metallic vs ceramic brackets). SBS was evaluated using a universal testing machine. The adhesive remnant index (ARI) was registered and surfaces were observed under SEM. Surface treatment and bracket type significantly affected the bracket-zirconia bond strength. SBS was significantly higher (p<0.001) for ceramic brackets in all groups (APA+FS > APA > FS > SC > control) than metallic brackets (APA+FS > FS > SC > APA > control). For metallic brackets, groups SC (5.99 ± 1.86 MPa), FS (6.72 ± 2.30 MPa) and APA+FS (7.22 ± 2.73 MPa) reported significantly higher bond strengths than other groups (p < 0.05). For ceramic brackets, the highest bond strength values were obtained in groups APA (25.01 ± 4.45 MPa), FS (23.18 ± 6.51 MPa) and APA+FS (29.22 ± 8.20 MPa).Femtosecond laser enhances bond strength of ceramic and metallic brackets to zirconia. Ceramic brackets provide significantly stronger adhesion than metallic brackets regardless of the surface treatment method.

Effect of Cold Deformation and Annealing on the Microstructure and Tensile Properties of a HfNbTaTiZr Refractory High Entropy Alloy

NASA Astrophysics Data System (ADS)

Senkov, O. N.; Pilchak, A. L.; Semiatin, S. L.

2018-05-01

The microstructure and tensile properties of HfNbTaTiZr after cold working and annealing were investigated. Cold work was introduced by axial compression followed by rolling resulting in a total thickness reduction of 89 pct without any evidence of cracking. The cold-worked material retained a single-phase microstructure and had a room temperature tensile yield stress σ 0.2 = 1438 MPa, peak true stress σ p = 1495 MPa, and true fracture strain ɛ f = 5 pct. Annealing at 800 °C for up to 256 hours resulted in the precipitation of Nb and Ta rich particles with a BCC crystal structure inside a Hf-and-Zr-enriched BCC matrix. The second phase particles nucleated heterogeneously inside deformation bands and slip lines and coarsened during annealing. Analysis of the coarsening behavior suggested that kinetics were controlled by the diffusion of Nb and Ta. In the two-phase material, σ 0.2 and σ p decreased from 1159 to 1071 MPa and from 1174 to 1074 MPa, respectively, with an increase in particle diameter from 0.18 to 0.72 μm, while ɛ f remained between 5 and 8 pct. Full recrystallization and normal grain growth, with the activation energy of 238 kJ/mol and activation volume of 5.3 to 9.6 m3/mol, occurred during annealing above 1000 °C. After heat treatment at this temperature, the alloy was characterized by a single-phase BCC structure with σ 0.2 = 1110 to 1115 MPa, σ p = 1160 to 1195 MPa, and ɛ f = 12 to 19 pct with the maximum values attained after annealing for 1 hour.

Hydrostatic pressure modifies the action of octanol and atropine on frog endplate conductance.

PubMed Central

Ashford, M. L.; Macdonald, A. G.; Wann, K. T.

1984-01-01

The effects of octanol, ethanol and atropine were examined on the time course of decay (tau D) of miniature endplate currents (m.e.p.cs) in the frog neuromuscular junction at normal and high pressure. Octanol (25-100 microM) decreased reversibly the tau D of m.e.p.cs in a dose-dependent manner, 100 microM reducing tau D to 0.39 of the control value. Higher concentrations (200-500 microM) additionally depressed the amplitude of m.e.p.cs. Hydrostatic pressure (3.19 and 5.25 MPa) reduced the tau D of octanol (25-100 microM)-shortened m.e.p.cs. Thus 3.19 MPa and 5.25 MPa reduced the tau D in the presence of 100 microM octanol to 0.75 and 0.78 of the octanol treated values. This effect was not completely reversed on decompression. The m.e.p.c. amplitude is reversibly decreased by pressure in the presence of octanol. Hydrostatic pressure (3.19-15.55 MPa) did not modify the effect of ethanol on tau D. At 10.40 and 15.55 MPa the tau D was increased equally in the absence or presence of ethanol. Atropine (60 microM) reduced the tau D and amplitude of m.e.p.cs to 0.33 and 0.63 of the control values. These effects were completely reversible. Hydrostatic pressure (3.19 and 5.25 MPa) reduced the tau D of atropine-shortened m.e.p.cs to 0.82 and 0.77 of the atropine-treated values respectively. This effect was not completely reversed on decompression. Hydrostatic pressure also reversibly depressed the amplitude of atropine-treated m.e.p.cs. The implications of these drug-hydrostatic pressure interactions are discussed. PMID:6333262

The Outcomes of Patients with ESRD and ANCA-Associated Vasculitis in Australia and New Zealand

PubMed Central

Tang, Wen; Bose, Bhadran; McDonald, Stephen P.; Hawley, Carmel M.; Badve, Sunil V.; Boudville, Neil; Brown, Fiona G.; Clayton, Philip A.; Campbell, Scott B.; Peh, Chen Au

2013-01-01

Summary Background and objectives This study aimed to evaluate dialysis and transplant outcomes of patients with ESRD secondary to ANCA-associated vasculitis (AAV). Design, setting, participants, & measurements All ESRD patients who commenced renal replacement therapy in Australia and New Zealand between 1996 and 2010 were included. Outcomes were assessed by Kaplan–Meier, multivariable Cox regression, and competing-risks regression survival analyses. Results Of 36,884 ESRD patients, 228 had microscopic polyangiitis (MPA) and 221 had granulomatosis with polyangiitis (GPA). Using competing-risks regression, compared with other causes of ESRD, MPA patients (hazard ratio [HR], 0.89; 95% confidence interval [95% CI], 0.73–1.08; P=0.24) and GPA patients (HR, 0.94; 95% CI, 0.74–1.19; P=0.62) experienced comparable survival on dialysis. Forty-six MPA patients (21%) and 47 GPA (20%) patients received 98 renal allografts. Respective 10-year first graft survival rates in MPA, GPA, and non-AAV patients were 50%, 62%, 70%, whereas patient survival rates were 68%, 85% and 83%, respectively. Compared with non-AAV patients, MPA transplant recipients had higher risks of graft failure (HR, 1.87; 95% CI, 1.07–3.25; P=0.03) and death (HR, 1.94; 95% CI, 1.02–3.69; P=0.04), whereas GPA transplant recipients experienced comparable renal allograft survival (HR, 0.91; 95% CI, 0.43–1.93; P=0.81) and patient survival (HR, 0.58; 95% CI, 0.23–2.27; P=0.58). AAV recurrence was observed in two renal allografts (2%). Conclusions Compared with ESRD patients without AAV, those with GPA have comparable renal replacement therapy outcomes, whereas MPA patients have comparable dialysis survival but poorer renal transplant allograft and patient survival rates. PMID:23349331

Development and testing of a new framework for rapidly assessing legal and managerial protection afforded by marine protected areas: Mediterranean Sea case study.

PubMed

Rodríguez-Rodríguez, D; Rodríguez, J; Abdul Malak, D

2016-02-01

The Convention on Biological Diversity (CBD) states the need to effectively conserve at least 10% of coastal and marine areas of particular importance for biodiversity by 2020. Here, a new indicator-based methodological framework to assess biodiversity protection afforded by marine protected areas' (MPA) was developed as a quick surrogate for MPAs' potential conservation effectiveness: the Marine Protected Area Protection Assessment Framework (MaPAF). The MaPAF consists of a limited number of headline indicators that are integrated in two indexes: Legal protection and Management effort, which eventually integrate in the overall MPA Protection super-index. The MaPAF was then tested in the Mediterranean MPA network as a case study. Spatial analyses were performed at three meaningful scales: the whole Mediterranean Sea, Mediterranean ecoregions and countries. The results of this study suggest that: 1) The MaPAF can serve as a useful tool for consistent, adaptive, quick and cost-effective MPA effectiveness assessments of MPAs and MPA networks in virtually any marine region, as the headline indicators used are commonly compiled and easy to retrieve; 2) The MaPAF proved usable and potentially relevant in the Mediterranean Sea where most indicators in the framework can be publicly accessed through the MAPAMED database and are planned to be regularly updated; 3) Protection afforded by MPAs is low across the whole Mediterranean, with only few MPAs having relatively high legal and managerial protection; and 4) Most Mediterranean countries need to devote substantially more work to improve MPA effectiveness mainly through increased management effort. Copyright © 2015 Elsevier Ltd. All rights reserved.

Intraspecific differences in drought tolerance and acclimation in hydraulics of Ligustrum vulgare and Viburnum lantana.

PubMed

Beikircher, Barbara; Mayr, Stefan

2009-06-01

An adequate general drought tolerance and the ability to acclimate to changing hydraulic conditions are important features for long-lived woody plants. In this study, we compared hydraulic safety (water potential at 50% loss of conductivity, Psi(50)), hydraulic efficiency (specific conductivity, k(s)), xylem anatomy (mean tracheid diameter, d(mean), mean hydraulic diameter, d(h), conduit wall thickness, t, conduit wall reinforcement, (t/b)(h)(2)) and stomatal conductance, g(s), of forest plants as well as irrigated and drought-treated garden plants of Ligustrum vulgare L. and Viburnum lantana L. Forest plants of L. vulgare and V. lantana were significantly less resistant to drought-induced cavitation (Psi(50) at -2.82 +/- 0.13 MPa and -2.79 +/- 0.17 MPa) than drought-treated garden plants (- 4.58 +/- 0.26 MPa and -3.57 +/- 0.15 MPa). When previously irrigated garden plants were subjected to drought, a significant decrease in d(mean) and d(h) and an increase in t and (t/b)(h)(2) were observed in L. vulgare. In contrast, in V. lantana conduit diameters increased significantly but no change in t and (t/b)(h)(2) was found. Stomatal closure occurred at similar water potentials (Psi(sc)) in forest plants and drought-treated garden plants, leading to higher safety margins (Psi(sc) - Psi(50)) of the latter (L. vulgare 1.63 MPa and V. lantana 0.43 MPa). These plants also showed higher g(s) at moderate Psi, more abrupt stomatal closure and lower cuticular conductivity. Data indicate that the development of drought-tolerant xylem as well as stomatal regulation play an important role in drought acclimation, whereby structural and physiological responses to drought are species-specific and depend on the plant's hydraulic strategy.

Drivers of coral reef marine protected area performance

PubMed Central

Hargreaves-Allen, Venetia Alexa; Mourato, Susana; Milner-Gulland, Eleanor Jane

2017-01-01

Coral reefs are severely threatened and a principal strategy for their conservation is marine protected areas (MPAs). However the drivers of MPA performance are complex and there are likely to be trade-offs between different types of performance (e.g. conservation or welfare related outcomes). We compiled a global dataset from expert knowledge for 76 coral reef MPAs in 33 countries and identified a set of performance measures reflecting ecological and socio-economic outcomes, achievement of aims and reduction of threats, using spatial or temporal comparisons wherever possible. We wanted to test the extent to which distinct types of performance occurred simultaneously, understood as win-win outcomes. Although certain performance measures were correlated, most were not, suggesting trade-offs that limit the usefulness of composite performance scores. Hypotheses were generated as to the impact of MPA features, aims, location, management and contextual variables on MPA performance from the literature. A multivariate analysis was used to test hypotheses as to the relative importance of these “drivers” on eight uncorrelated performance measures. The analysis supported some hypotheses (e.g. benefit provision for the local community improved performance), but not others (e.g. higher overall budget and more research activity did not). Factors endogenous to the MPA (such as size of the no-take area) were generally more significant drivers of performance than exogenous ones (such as national GDP). Different types of performance were associated with different drivers, exposing the trade-offs inherent in management decisions. The study suggests that managers are able to influence MPA performance in spite of external threats and could inform adaptive management by providing an approach to test for the effects of MPA features and management actions in different contexts and so to inform decisions for allocation of effort or funds to achieve specific goals. PMID:28644890

GABAergic Transmission in Rat Pontine Reticular Formation Regulates the Induction Phase of Anesthesia and Modulates Hyperalgesia Caused by Sleep Deprivation

PubMed Central

Vanini, Giancarlo; Nemanis, Kriste; Baghdoyan, Helen A.; Lydic, Ralph

2014-01-01

The oral part of the pontine reticular formation (PnO) contributes to the regulation of sleep, anesthesia, and pain. The role of PnO GABA in modulating these states remains incompletely understood. The present study used time to Loss and time to Resumption of Righting Response (LoRR and RoRR) as surrogate measures of loss and resumption of consciousness. This study tested three hypotheses: (1) pharmacologically manipulating GABA levels in rat PnO alters LoRR, RoRR, and nociception; (2) propofol decreases GABA levels in the PnO; and (3) inhibiting GABA synthesis in the PnO blocks hyperalgesia caused by sleep deprivation. Administering a GABA synthesis inhibitor (3-MPA) or a GABA uptake inhibitor (NPA) into rat PnO significantly altered LoRR caused by propofol. 3-MPA significantly decreased LoRR for propofol (−18%). NPA significantly increased LoRR during administration of propofol (36%). Neither 3-MPA nor NPA altered RoRR following cessation of propofol or isoflurane delivery. The finding that LoRR was decreased by 3-MPA and increased by NPA is consistent with measures showing that extracellular GABA levels in the PnO were decreased (41%) by propofol. Thermal nociception was significantly decreased by 3-MPA and increased by NPA, and 3-MPA blocked the hyperalgesia caused by sleep deprivation. The results demonstrate that GABA levels in the PnO regulate the time for loss of consciousness caused by propofol, extend the concept that anesthetic induction and emergence are not inverse processes, and suggest that GABAergic transmission in the PnO mediates hyperalgesia caused by sleep loss. PMID:24674578

GABAergic transmission in rat pontine reticular formation regulates the induction phase of anesthesia and modulates hyperalgesia caused by sleep deprivation.

PubMed

Vanini, Giancarlo; Nemanis, Kriste; Baghdoyan, Helen A; Lydic, Ralph

2014-07-01

The oral part of the pontine reticular formation (PnO) contributes to the regulation of sleep, anesthesia and pain. The role of PnO γ-aminobutyric acid (GABA) in modulating these states remains incompletely understood. The present study used time to loss and time to resumption of righting response (LoRR and RoRR) as surrogate measures of loss and resumption of consciousness. This study tested three hypotheses: (i) pharmacologically manipulating GABA levels in rat PnO alters LoRR, RoRR and nociception; (ii) propofol decreases GABA levels in the PnO; and (iii) inhibiting GABA synthesis in the PnO blocks hyperalgesia caused by sleep deprivation. Administering a GABA synthesis inhibitor [3-mercaptopropionic acid (3-MPA)] or a GABA uptake inhibitor [nipecotic acid (NPA)] into rat PnO significantly altered LoRR caused by propofol. 3-MPA significantly decreased LoRR for propofol (-18%). NPA significantly increased LoRR during administration of propofol (36%). Neither 3-MPA nor NPA altered RoRR following cessation of propofol or isoflurane delivery. The finding that LoRR was decreased by 3-MPA and increased by NPA is consistent with measures showing that extracellular GABA levels in the PnO were decreased (41%) by propofol. Thermal nociception was significantly decreased by 3-MPA and increased by NPA, and 3-MPA blocked the hyperalgesia caused by sleep deprivation. The results demonstrate that GABA levels in the PnO regulate the time for loss of consciousness caused by propofol, extend the concept that anesthetic induction and emergence are not inverse processes, and suggest that GABAergic transmission in the PnO mediates hyperalgesia caused by sleep loss. © 2014 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

Finite-Element Modeling of 3C-SiC Membranes

NASA Technical Reports Server (NTRS)

DeAnna, R. G.; Mitchell, J.; Zorman, C. A.; Mehregany, M.

2000-01-01

Finite-element modeling (FEM) of 3C-SiC thin-film membranes on Si substrates was used to determine the residual stress and center deflection with applied pressure. The anisotropic, three-dimensional model includes the entire 3C-SiC membrane and Si substrate with appropriate material properties and boundary conditions. Residual stress due to the thermal-expansion-coefficient mismatch between the3C-SiC film and Si substrate was included in the model. Both before-and after-etching, residual stresses were calculated. In-plane membrane stress and normal deflection with applied pressure were also calculated. FEM results predict a tensile residual stress fo 259 MPa in the 3C-SiC membrane before etching. This decreases to 247 MPa after etching the substrate below the membrane. The residual stress experimentally measured on sample made at Case Western Reserve University was 280 MPa on post-etched membranes. This is excellent agreement when an additional 30-40 MPa of residual stress to account for lattice mismatch is added to the FEM results.

Epoxy Resins Toughened with Surface Modified Epoxidized Natural Rubber Fibers by One-Step Electrospinning.

PubMed

Kim, Joo Ran; Kim, Jung J

2017-04-27

Epoxidized natural rubber fibers (ERFs) are developed through one-step electrospinning and directly deposited into epoxy resins without collecting and distributing of fibers. The shape of ERFs shows rough surface due to different evaporation rate of solvent mixture consisting of chloroform and dichloromethane and the average diameter of ERFs is 6.2 µm. The increase of ERFs loading from 0 to 20 wt % into the epoxy resin increases the fracture strain significantly from 1.2% to 13% and toughness from 0.3 MPa to 1.9 MPa by a factor of 7. However, the tensile strength and Young's modulus decrease about 34% from 58 MPa to 34 MPa and from 1.4 GPa to 0.9 GPa, respectively. Due to the crosslinking reactions between oxirane groups of ERFs and amine groups in the resin, surface roughness and the high aspect ratio of ERFs, ERFs result in more effective toughening effect with the minimum loss of tensile properties in epoxy resins.

Effect of ultraviolet light irradiation and sandblasting treatment on bond strengths between polyamide and chemical-cured resin.

PubMed

Asakawa, Yuya; Takahashi, Hidekazu; Iwasaki, Naohiko; Kobayashi, Masahiro

2014-01-01

The aim of this study was to evaluate the effects of ultraviolet light (UV) irradiation and sandblasting treatment on the shear bond strength between polyamide and chemical-cured resin. Three types of commercial polyamides were treated using UV irradiation, sandblasting treatment, and a combining sandblasting and UV irradiation. The shear bond strength was measured and analyzed using the Kruskal-Wallis test (α=0.05). Comparing shear bond strengths without surface treatment, from 4.1 to 5.7 MPa, the UV irradiation significantly increased the shear bond strengths except for Valplast, whose shear bond strengths ranged from 5.2 to 9.3 MPa. The sandblasting treatment also significantly increased the shear bond strengths (8.0 to 11.4 MPa). The combining sandblasting and UV irradiation significantly increased the shear bond strengths (15.2 to 18.3 MPa) comparing without surface treatment. This combined treatment was considered the most effective at improving the shear bond strength between polyamide and chemical-cured resin.

Effect of high hydrostatic pressure on functional properties and quality characteristics of Aloe vera gel (Aloe barbadensis Miller).

PubMed

Vega-Gálvez, Antonio; Miranda, Margarita; Aranda, Mario; Henriquez, Karem; Vergara, Judith; Tabilo-Munizaga, Gipsy; Pérez-Won, Mario

2011-12-01

The aim of this study was to evaluate the effects of high hydrostatic pressure treatment at three pressure levels (300, 400 and 500Mpa) on the functional and quality characteristics of Aloe vera gel including vitamin C and E, aloin, minerals, phenolic content and antioxidant activity. The results show that HHP exerted a clear influence on minerals content, vitamin C and E content, antioxidant activity, total phenolic and aloin content. After 35days of storage all treated samples presented a decrease in mineral content, except for phosphorus. Total phenolic content and vitamin C and E content decreased at high pressures (500MPa), while all pressurised samples showed a higher antioxidant activity and aloin content than untreated sample after 35days of storage. The maximum values of antioxidant activity and aloin were 6.55±1.26μg/ml at 300MPa and 24.23±2.27mg/100g d.m. at 400MPa. Copyright © 2011 Elsevier Ltd. All rights reserved.

Measurement and Modeling of Acoustic Fields in a Gel Phantom at High Intensities

NASA Astrophysics Data System (ADS)

Canney, Michael S.; Bailey, Michael R.; Khokhlova, Vera A.; Crum, Lawrence A.

2006-05-01

The goal of this work was to compare measured and numerically predicted HIFU pressure waveforms in water and a tissue-mimicking phantom. Waveforms were measured at the focus of a 2-MHz HIFU transducer with a fiber optic hydrophone. The transducer was operated with acoustic powers ranging from 2W to 300W. A KZK-type equation was used for modeling the experimental conditions. Strongly asymmetric nonlinear waves with peak positive pressure up to 80 MPa and peak negative pressure up to 20 MPa were measured in water, while waves up to 50 MPa peak positive pressure and 15 MPa peak negative pressure were measured in tissue phantoms. The values of peak negative pressure corresponded well with numerical simulations and were significantly smaller than predicted by linear extrapolation from low-level measurements. The values of peak positive pressures differed only at high levels of excitation where bandwidth limitations of the hydrophone failed to fully capture the predicted sharp shock fronts.

System Mass Variation and Entropy Generation in 100k We Closed-Brayton-Cycle Space Power Systems

NASA Technical Reports Server (NTRS)

Barrett, Michael J.; Reid, Bryan M.

2004-01-01

State-of-the-art closed-Brayton-cycle (CBC) space power systems were modeled to study performance trends in a trade space characteristic of interplanetary orbiters. For working-fluid molar masses of 48.6, 39.9, and 11.9 kg/kmol, peak system pressures of 1.38 and 3.0 MPa and compressor pressure ratios ranging from 1.6 to 2.4, total system masses were estimated. System mass increased as peak operating pressure increased for all compressor pressure ratios and molar mass values examined. Minimum mass point comparison between 72 percent He at 1.38 MPa peak and 94 percent He at 3.0 MPa peak showed an increase in system mass of 14 percent. Converter flow loop entropy generation rates were calculated for 1.38 and 3.0 MPa peak pressure cases. Physical system behavior was approximated using a pedigreed NASA Glenn modeling code, Closed Cycle Engine Program (CCEP), which included realistic performance prediction for heat exchangers, radiators and turbomachinery.

Changes in protein structures to improve the rheology and texture of reduced-fat sausages using high pressure processing.

PubMed

Yang, Huijuan; Khan, Muhammad Ammar; Yu, Xiaobo; Zheng, Haibo; Han, Minyi; Xu, Xinglian; Zhou, Guanghong

2016-11-01

This study investigated the role of high-pressure processing (HPP) for improving the functional properties of meat batters and the textural properties of reduced-fat sausages. Application of 200MPa pressure at 10°C for 2min to pork batters containing various fat contents (0-30%) affected their rheological properties, cooking losses, color, textual properties and their protein imaging. The results revealed that both application of 200MPa and increasing fat content decreased cooking loss, as well as improved the textural and rheological properties. Cooking losses, texture and sensory evaluation of 200MPa treated sausages having 20% fat were similar to those of the 0.1MPa treated sausages having 30% fat. Principal component analysis revealed that certain quality attributes were affected differently by the levels of fat addition and by HPP. These findings indicated the potential of HPP for improving yield and texture of emulsion-type sausages having reduced fat contents. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of high hydrostatic pressure on the color and texture parameters of refrigerated Caiman (Caiman crocodilus yacare) tail meat.

PubMed

Canto, A C V C S; Lima, B R C C; Cruz, A G; Lázaro, C A; Freitas, D G C; Faria, Jose A F; Torrezan, R; Freitas, M Q; Silva, T P J

2012-07-01

The effect of applying high hydrostatic pressure (HHP) on the instrumental parameters of color and texture and sensory characteristics of alligator meat were evaluated. Samples of alligator tail meat were sliced, vacuum-packed, pressurized and distributed into four groups: control, treated with 200 MPa/10 min, 300 MPa/10 min and 400 MPa/10 min, then stored at 4°C±1°C for 45 days. Instrumental color, texture profile and a sensory profiling using quantitative descriptive analysis were carried out on the 1st, 15th, 30th and 45th days of storage. HHP was shown to affect the color and texture of the product, and the sensory descriptors (p<0.05). The results suggest that high pressure is a promising technology for the processing of alligator meat, especially low pressures (200 MPa) which can have positive effects on the quality of the product. Copyright © 2012 Elsevier Ltd. All rights reserved.

System Mass Variation and Entropy Generation in 100-kWe Closed-Brayton-Cycle Space Power Systems

NASA Technical Reports Server (NTRS)

Barrett, Michael J.; Reid, Bryan M.

2004-01-01

State-of-the-art closed-Brayton-cycle (CBC) space power systems were modeled to study performance trends in a trade space characteristic of interplanetary orbiters. For working-fluid molar masses of 48.6, 39.9, and 11.9 kg/kmol, peak system pressures of 1.38 and 3.0 MPa and compressor pressure ratios ranging from 1.6 to 2.4, total system masses were estimated. System mass increased as peak operating pressure increased for all compressor pressure ratios and molar mass values examined. Minimum mass point comparison between 72 percent He at 1.38 MPa peak and 94 percent He at 3.0 MPa peak showed an increase in system mass of 14 percent. Converter flow loop entropy generation rates were calculated for 1.38 and 3.0 MPa peak pressure cases. Physical system behavior was approximated using a pedigreed NASA Glenn modeling code, Closed Cycle Engine Program (CCEP), which included realistic performance prediction for heat exchangers, radiators and turbomachinery.

Financing marine protected areas through visitor fees: insights from tourists willingness to pay in Chile.

PubMed

Gelcich, Stefan; Amar, Francisca; Valdebenito, Abel; Castilla, Juan Carlos; Fernandez, Miriam; Godoy, Cecilia; Biggs, Duan

2013-12-01

Tourism is a financing mechanism considered by many donor-funded marine conservation initiatives. Here we assess the potential role of visitor entry fees, in generating the necessary revenue to manage a marine protected area (MPA), established through a Global Environmental Facility Grant, in a temperate region of Chile. We assess tourists' willingness to pay (WTP) for an entry fee associated to management and protection of the MPA. Results show 97 % of respondents were willing to pay an entrance fee. WTP predictors included the type of tourist, tourists' sensitivity to crowding, education, and understanding of ecological benefits of the MPA. Nature-based tourists state median WTP values of US$ 4.38 and Sun-sea-sand tourists US$ 3.77. Overall, entry fees could account for 10-13 % of MPA running costs. In Chile, where funding for conservation runs among the weakest in the world, visitor entry fees are no panacea in the short term and other mechanisms, including direct state/government support, should be considered.

Study on titanium-magnesium composites with bicontinuous structure fabricated by powder metallurgy and ultrasonic infiltration.

PubMed

Jiang, S; Huang, L J; An, Q; Geng, L; Wang, X J; Wang, S

2018-05-01

Titanium-magnesium (Ti-Mg) composites with bicontinuous structure have been successfully fabricated by powder metallurgy and ultrasonic infiltration for biomaterial potential. In the composites, Ti phase is distributed continuously by sintering necks, while Mg phase is also continuous, distributing at the interconnected pores surrounding the Ti phase. The results showed that the fabricated Ti-Mg composites exhibited low modulus and high strength, which are very suitable for load bearing biomedical materials. The composites with 100 µm and 230 µm particle sizes exhibited Young's modulus of 37.6 GPa and 23.4 GPa, 500.7 MPa and 340 MPa of compressive strength and 631.5 MPa and 375.2 MPa of bending strength, respectively. Moreover, both of the modulus and strength of the composites increase with decreasing of Ti particle sizes. In vitro study has been done for the preliminary evaluation of the Ti-Mg composites. Copyright © 2018 Elsevier Ltd. All rights reserved.

MPA Portable: A Stand-Alone Software Package for Analyzing Metaproteome Samples on the Go.

PubMed

Muth, Thilo; Kohrs, Fabian; Heyer, Robert; Benndorf, Dirk; Rapp, Erdmann; Reichl, Udo; Martens, Lennart; Renard, Bernhard Y

2018-01-02

Metaproteomics, the mass spectrometry-based analysis of proteins from multispecies samples faces severe challenges concerning data analysis and results interpretation. To overcome these shortcomings, we here introduce the MetaProteomeAnalyzer (MPA) Portable software. In contrast to the original server-based MPA application, this newly developed tool no longer requires computational expertise for installation and is now independent of any relational database system. In addition, MPA Portable now supports state-of-the-art database search engines and a convenient command line interface for high-performance data processing tasks. While search engine results can easily be combined to increase the protein identification yield, an additional two-step workflow is implemented to provide sufficient analysis resolution for further postprocessing steps, such as protein grouping as well as taxonomic and functional annotation. Our new application has been developed with a focus on intuitive usability, adherence to data standards, and adaptation to Web-based workflow platforms. The open source software package can be found at https://github.com/compomics/meta-proteome-analyzer .

Shear strength of a three-dimensional capillary-porous titanium coating for biomedical applications

NASA Astrophysics Data System (ADS)

Kalita, V. I.; Komlev, D. I.; Radyuk, A. A.; Ivannikov, A. Yu; Alpatov, A. V.; Komlev, V. S.; Mamonov, V. I.; Sevostyanov, M. A.; Baikin, A. S.

2018-04-01

The effect of pretreatment and plasma preheating of Ti-substrate on shear strength of three-dimensional capillary porous Ti-coating was studied. After sandblasting the shear strength of the plasma sprayed coating was 200 ± 2 MPa, and after additional matting it was 68 ± 4 MPa. The use of plasma preheating of the substrates for 9 seconds decreased difference between values of the shear strength to 249 ± 17 MPa and 229 ± 16 MPa, respectively. After plasma spraying the microhardness of the surface layer of the substrate was 4.34 ± 0.35 GPa, the microhardness of the boundary between the coating and the substrate was 8.08 ± 0.45 GPa, and the microhardness of the coating was 3.48 ± 0.25 GPa. High shear strength of the coating was attributed to the activation of the substrate by means of plasma preheating and hardening of the boundary between the coating and the substrate by oxides and nitrides.

Epoxy Resins Toughened with Surface Modified Epoxidized Natural Rubber Fibers by One-Step Electrospinning

PubMed Central

Kim, Joo Ran; Kim, Jung J.

2017-01-01

Epoxidized natural rubber fibers (ERFs) are developed through one-step electrospinning and directly deposited into epoxy resins without collecting and distributing of fibers. The shape of ERFs shows rough surface due to different evaporation rate of solvent mixture consisting of chloroform and dichloromethane and the average diameter of ERFs is 6.2 µm. The increase of ERFs loading from 0 to 20 wt % into the epoxy resin increases the fracture strain significantly from 1.2% to 13% and toughness from 0.3 MPa to 1.9 MPa by a factor of 7. However, the tensile strength and Young’s modulus decrease about 34% from 58 MPa to 34 MPa and from 1.4 GPa to 0.9 GPa, respectively. Due to the crosslinking reactions between oxirane groups of ERFs and amine groups in the resin, surface roughness and the high aspect ratio of ERFs, ERFs result in more effective toughening effect with the minimum loss of tensile properties in epoxy resins. PMID:28772822

Effect of high pressure processing on textural and microbiological quality of pink perch (Nemipterus japonicus) sausage during chilled storage

NASA Astrophysics Data System (ADS)

Kunnath, Sarika; Panda, Satyen Kumar; Jaganath, Bindu; Gudipati, Venkateshwarlu

2015-10-01

The non-thermal high pressure (HP) processing was studied on fish sausage to enhance the quality during chilled storage. Pink perch (Nemipterus japonicus) sausages, packed in poly amide casing under vacuum were subjected to 400, 500 and 600 MPa pressures (dwell time: 10 min and ramp rate: 300 MPa/min) and compared with heat-set samples for physico-chemical and microbial quality parameters. Pressurized samples formed softer and glossier gels with a slight reduction in water-holding capacity. HP made the texture of sausage softer, cohesive and less chewy and gummier than heat-treated ones. Folding test seen higher acceptance values in samples treated at 500 and 600 MPa, during storage. Maximum log reduction in microbial count was observed in 600 MPa immediately, and significant difference in cooked and pressurized sausages was seen only up to 7th day. This revealed the potential application of HP in replacing conventional heat treatment for sausages preparation with enhanced shelf-life.

Clinical and metabolic effects of medroxyprogesterone acetate and ethinyl estradiol plus drospirenone in women with polycystic ovary syndrome.

PubMed

Ozdemir, Suna; Görkemli, Hüseyin; Gezginç, Kazim; Ozdemir, Mustafa; Kiyici, Aysel

2008-10-01

To investigate the effects of treatment with medroxyprogesterone acetate (MPA), 10 days per month for 6 months, on lipid and carbohydrate metabolism in women with polycystic ovary syndrome (PCOS). Sixty-three women with PCOS were randomized to receive MPA or ethinyl estradiol plus drospirenone. There were no changes in lipid or carbohydrate metabolism in the MPA group, but serum levels of luteinizing hormone (P<0.001) and total testosterone (P<0.003) significantly decreased, as did the free androgen index (P<0.02) and acne (P<0.03) and seborrhea (P<0.04) scores. In the ethinyl estradiol plus drospirenone group lipid and hormone values significantly increased whereas acne, seborrhea, hair loss, and Ferriman-Gallwey scores decreased. There was no statistically significant change in the total cholesterol to high-density cholesterol ratio in either group. Treatment of PCOS patients with MPA provided good menstrual cycle control, beneficial changes in hormonal values associated with hyperandrogenism, and no significant changes in lipid or carbohydrate metabolism.

The synthesis of ZrO2-Y2O3 ceramic fibers by the method of impregnation of viscous threads

NASA Astrophysics Data System (ADS)

Titova, S. M.; Obabkov, N. V.; Zakirova, A. F.; Zakirov, I. F.; Dokuchaev, V. S.; Shak, A. V.

2017-09-01

The possibility of synthesis of ZrO2-Y2O3 oxide fibers and their applicatiuon for reinforcing porous ceramics of the same composition was investigated. Ceramic fibers were obtained by impregnating viscose strings with solutions of zirconyl and yttrium nitrates. The method allows synthesis of the fibers with a diameter of 400 µm and length of 5 to 20 mm. The strength of the synthesized fibers was determined. The maximum tensile strength (132.45 MPa) was demonstrated by fibers obtained with a working solution concentration of 500 g oxides/L. Repeated impregnation of the viscose yarn led to an increase in the strength of the fibers to 205 MPa. Ceramic fibers can be used as reinforcing elements of oxide ceramics. The bending strength of the reinforced ceramics was 3 MPa. After 10 cycles of thermal cycling (heating to 1100 °C and cooling in water) the bending strength was reduced to 1 MPa.

Extent and frequency of vessel oil spills in US marine protected areas.

PubMed

Dalton, Tracey; Jin, Di

2010-11-01

Little is known about how marine protected areas (MPAs) may be vulnerable to vessel oil spills in the United States. This study investigated individual size, frequency, and total amount of vessel oil spilled in US MPAs, and how characteristics of MPAs and individual spill events influenced spills. Vessel oil spills in US waters (2002-06) and MPA boundaries were mapped. Total number and volume of oil spills inside and outside MPAs were computed. Results show that the presence of a MPA does not seem to prevent vessel oil spills or reduce the amount of oil spilled, and that a variety of MPA attributes (e.g., scale of protection, fishing restrictions, and others) and spill event characteristics (e.g., vessel type, year of spill, and others) affect oil spills inside and outside MPAs. These results can be used to develop MPA rules and marine transportation policies that reduce the vulnerability of sensitive resources to oil spills. Copyright © 2010 Elsevier Ltd. All rights reserved.

Climate change-induced water stress suppresses the regeneration of the critically endangered forest tree Nyssa yunnanensis

PubMed Central

Zhang, Shanshan; Kang, Hongmei; Yang, Wenzhong

2017-01-01

Climatic change-induced water stress has been found to threaten the viability of trees, especially endangered species, through inhibiting their recruitment. Nyssa yunnanensis, a plant species with extremely small populations (PSESP), consists of only two small populations of eight mature individuals remaining in southwestern China. In order to determine the barriers to regeneration, both in situ and laboratory experiments were performed to examine the critical factors hindering seed germination and seedling establishment. The results of in situ field experiments demonstrated that soil water potentials lower than -5.40 MPa (experienced in December) had significantly inhibitory effects on seedling survival, and all seedlings perished at a soil water potential of -5.60 MPa (January). Laboratory experiments verified that N. yunnanensis seedlings could not survive at a 20% PEG 6000 concentration (-5.34 MPa) or 1/5 water-holding capacity (WHC; -5.64 MPa), and seed germination was inhibited in the field from September (-1.10 MPa) to November (-4.30 MPa). Our results suggested that soil water potentials between -5.34 and -5.64 MPa constituted the range of soil water potentials in which N. yunnanensis seedlings could not survive. In addition to water deficit, intensified autotoxicity, which is concentration-dependent, resulted in lower seed germination and seedling survival. Thus, seed establishment was probably simultaneously impacted by water deficit and aggravated autotoxicity. Meteorological records from the natural distribution areas of N. yunnanensis indicated that mean annual rainfall and relative humidity have declined by 21.7% and 6.3% respectively over past 55 years, while the temperature has increased by 6.0%. Climate change-induced drought, along with a poor resistance and adaptability to drought stress, has severely impacted the natural regeneration of N. yunnanensis. In conclusion, climate change-induced drought has been implicated as a regulating factor in the natural regeneration of N. yunnanensis through suppressing seed germination and screening out seedlings in the dry season. Based on the experimental findings, habitat restoration and microclimate improvement should both be highlighted in the conservation of this particular plant species. PMID:28763476

Inactivation of Vibrio parahaemolyticus and Vibrio vulnificus in oysters by high-hydrostatic pressure and mild heat.

PubMed

Ye, Mu; Huang, Yaoxin; Chen, Haiqiang

2012-10-01

Several recent outbreaks associated with oysters have heightened safety concerns of raw shellfish consumptions, with the majority being attributed to Vibrio spp. The objective of this study was to determine the effect of high-hydrostatic pressure (HHP) followed by mild heating on the inactivation of Vibrio parahaemolyticus and Vibrio vulnificus in live oysters. Inoculated oysters were randomly subjected to: a) pressurization at 200-300 MPa for 2 min at 21 °C, b) mild heat treatment at 40, 45 or 50 °C for up to 20 min and c) pressure treatment of 200-300 MPa for 2 min at 21 °C followed by heat treatment at 40-50 °C. Counts of V. parahaemolyticus and V. vulnificus were then determined using the most probable number (MPN) method. Pressurization at 200-300 MPa for 2 min resulted in various degrees of inactivation, from 1.2 to >7 log MPN/g reductions. Heat treatment at 40 and 45 °C for 20 min only reduced V. parahaemolyticus and V. vulnificus by 0.7-2.5 log MPN/g while at 50 °C for 15 min achieved >7 log MPN/g reduction. HHP and mild heat had synergistic effects. Combinations such as HHP at 250 MPa for 2 min followed by heat treatment at 45 °C for 15 min and HHP at 200 MPa for 2 min followed by heat treatment at 50 °C for 5 min reduced both V. parahaemolyticus and V. vulnificus to non-detectable levels by the MPN method (<3 MPN/g). HHP at ≥275 MPa for 2 min followed by heat treatment at 45 °C for 20 min and HHP at ≥200 MPa for 2 min followed by heat treatment at 50 °C for 15 min completely eliminated both pathogens in oysters (negative enrichment results). This study demonstrated the efficiency of HHP followed by mild heat treatments on inactivation of V. parahaemolyticus and V. vulnificus and could help the industry to establish parameters for processing oysters. Copyright © 2012 Elsevier Ltd. All rights reserved.

Dissociation of Laboratory-Synthesized Methane Hydrate in Coarse-Grained Sediments by Slow Depressurization

NASA Astrophysics Data System (ADS)

Phillips, S. C.; You, K.; Borgfeldt, T.; Meyer, D.; Dong, T.; Flemings, P. B.

2016-12-01

We performed four dissociation experiments in which experimentally-formed methane hydrate was dissociated via slow, stepwise depressurization, revealing in situ salinity conditions. Overall, these results suggest the occurrence of local pore water freshening around dissociating hydrate in which bulk equilibrium behavior is limited by salt diffusion. Depressurization was performed at a constant confining temperature over 1 to 3 weeks by releasing small volumes of methane gas from the top of a vertically-oriented sample into an inverted graduated cylinder. We identify three distinct regimes of depressurization based on pressure drop behavior: (1) release of free gas down to initial hydrate dissociation at 3.3 MPa in NaBr or 4.64 MPa in NaCl, (2) dissociation of methane hydrate characterized by a slow, logarithmic increase in pressure after each gas release and (3) residual free gas release. Initial hydrate dissociation in NaCl brine at 4.64 MPa corresponds to the phase boundary for hydrate in 9.6 wt% NaCl. In the NaCl experiment, pressure increases of 0.16 MPa while the sample was shut in over 3 days likely correspond to a recovery in salinity of 0.7 wt. %. Salt ions likely diffuse from brine ahead of the hydrate front, based on a length scale for diffusion of NaCl of 6.3 cm for 3 days. In this experiment dissociation at bulk equilibrium is expected to decline from 4.54 to 4.04 MPa; however actual dissociation during 73 gas releases over 15 days, results in a pressure drop from 4.64 to 3.25 MPa. Hydrate samples were formed by injection of methane gas at 1 ºC and 12.24 MPa within a cylinder packed with medium-grained quartz sand and initially saturated in a 7 wt% NaBr or NaCl solution. In two experiments in which the system was thoroughly leak tested, total methane consumed during formation and recovered during depressurization match within 7% indicating this approach to be relatively accurate for determining total methane in experimental or pressure core samples.

Compaction and Permeability Reduction of Castlegate Sandstone under Pore Pressure Cycling

NASA Astrophysics Data System (ADS)

Bauer, S. J.

2014-12-01

We investigate time-dependent compaction and permeability changes by cycling pore pressure with application to compressed air energy storage (CAES) in a reservoir. Preliminary experiments capture the impacts of hydrostatic stress, pore water pressure, pore pressure cycling, chemical, and time-dependent considerations near a borehole in a CAES reservoir analog. CAES involves creating an air bubble in a reservoir. The high pressure bubble serves as a mechanical battery to store potential energy. When there is excess grid energy, bubble pressure is increased by air compression, and when there is energy needed on the grid, stored air pressure is released through turbines to generate electricity. The analog conditions considered are depth ~1 km, overburden stress ~20 MPa and a pore pressure ~10MPa. Pore pressure is cycled daily or more frequently between ~10 MPa and 6 MPa, consistent with operations of a CAES facility at this depth and may continue for operational lifetime (25 years). The rock can vary from initially fully-to-partially saturated. Pore pressure cycling changes the effective stress.Jacketed, room temperature tap water-saturated samples of Castlegate Sandstone are hydrostatically confined (20 MPa) and subjected to a pore pressure resulting in an effective pressure of ~10 MPa. Pore pressure is cycled between 6 to 10 MPa. Sample displacement measurements yielded determinations of volumetric strain and from water flow measurements permeability was determined. Experiments ran for two to four weeks, with 2 to 3 pore pressure cycles per day. The Castlegate is a fluvial high porosity (>20%) primarily quartz sandstone, loosely calcite cemented, containing a small amount of clay.Pore pressure cycling induces compaction (~.1%) and permeability decreases (~20%). The results imply that time-dependent compactive processes are operative. The load path, of increasing and decreasing pore pressure, may facilitate local loosening and grain readjustments that results in the compaction and permeability decreases observed. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Dept. of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.SAND2014-16586A

Transient porosity pulses and microfracturing during a stress-generating retrograde metamorphic reaction

NASA Astrophysics Data System (ADS)

Renard, F.; Zheng, X.; Cordonnier, B.; Zhu, W.; Jamtveit, B.

2017-12-01

Several geological processes involve mineral transformations where nominally dry rocks transform into hydrated ones when left in contact with water (i.e. eclogitization, serpentinization). In these systems, the transformation induces stress if the rock is confined, and the new minerals create a so-called force of crystallization. Here, we study a model retrograde metamorphic reaction, the hydration of periclase, MgO, into brucite, Mg(OH)2, to quantify the coupling between reaction, stress generation, porosity evolution and fracturing. This hydration reaction generates a volume increase of 110%, and a density decrease of 33.8% of the solid. Samples of a microporous MgO ceramics were reacted at 170-211°C, 5-80 MPa confining pressure, 6-95 MPa differential stress and 5 MPa pore fluid pressure. They were installed into an X-ray transparent triaxial deformation rig, called Hades, and mounted on a synchrotron microtomography stage. Each experiment lasted between 2 and 5 hours, during which between 35 and 130 three-dimensional images were acquired, allowing to follow the chemical transformation and the deformation of the sample. Below 30 MPa mean pressure, the hydration reaction was coupled to fracturing of the MgO ceramics, and the transformation rate followed a sigmoidal kinetics curve with a slow initiation, a fast reaction coupled to fracturing and the generation of a transient porosity pulse, and a slow-down until an almost complete transformation of periclase into brucite.. Conversely, above 30 MPa, the reaction kinetics was very slow, without fracturing over the time scale of the experiment. When considering the driving force of the hydration reaction, stress generation should be several hundreds MPa, whereas the present experiments show that fracturing occurred only below 30 MPa. This indicates that the potential energy due to phase transformation generates much lower stress than what is estimated from non-equilibrium thermodynamics. A possible interpretation of this observation is that the stress created by the reaction may overcome the disjoining pressure at the grain-grain interface, expelling the water film trapped there and reducing the kinetics of reaction. As a consequence, only a fraction of the available potential driving force was used to accelerate the reaction by microfracturing.

Reaction rim growth on olivine in silicic melts: Implications for magma mixing

USGS Publications Warehouse

Coombs, Michelle L.; Gardner, James E.

2004-01-01

Finely crystalline amphibole or pyroxene rims that form during reaction between silicic host melt and cognate olivine xenocrysts, newly introduced during magma mixing events, can provide information about the timing between mixing and volcanic eruptions. We investigated rim growth experimentally by placing forsteritic olivine in rhyolitic and rhyodacitic melts for times between 25 and 622 h at 50 and 150 MPa, H2O-saturated, at the Ni-NiO buffer. Rims of orthopyroxene microlites formed from high-silica rhyolite and rhyodacite melts at 885°C and 50 MPa, and in the rhyolite at 150 MPa and 885°C. Rims of amphibole with lesser orthopyroxene formed in the rhyolite at 150 MPa and 800°C and in the rhyodacite at 150 MPa and 885°C. Irregular, convolute olivine edges and mass balance between olivine, melt, and rim phases show that olivine partly dissolved at all conditions. Iron-rich zones at the exteriors of olivines, which increased in width parabolically with time, show that Fe-Mg interdiffusion occurring in olivines was not outpaced by olivine dissolution. Linear increases of the square of rim widths with time suggest that diffusion within the melt is the rate-controlling process for olivine dissolution and rim growth. Rims grew one-half to one order-of-magnitude faster when melt water contents were doubled, unless conditions were far above the liquidus. Rim growth rate in rhyolite increases from 0.055 ± 0.01 µm2/h at 885°C and 50 MPa to 0.64 ± 0.13 µm2/h at 800°C and 150 MPa. Melt composition has a lesser effect on rim growth rates, with growth rate increasing as melt SiO2 content decreases. Pyroxene rims on olivines in andesite erupted from Arenal volcano (Costa Rica) grew at a rate of 3.0 ± 0.2 µm2/h over an eleven-year period. This rate is faster than those of the experiments due to lower melt viscosity and higher temperatures, and suggests that a magma mixing event preceded the start of the eruption by days.

Elevational trends in hydraulic efficiency and safety of Pinus cembra roots.

PubMed

Losso, Adriano; Nardini, Andrea; Nolf, Markus; Mayr, Stefan

2016-04-01

In alpine regions, elevational gradients in environmental parameters are reflected by structural and functional changes in plant traits. Elevational changes in plant water relations have also been demonstrated, but comparable information on root hydraulics is generally lacking. We analyzed the hydraulic efficiency (specific hydraulic conductivity k s, entire root system conductance K R) and vulnerability to drought-induced embolism (water potential at 50 % loss of conductivity Ψ 50) of the roots of Pinus cembra trees growing along an elevational transect of 600 m. Hydraulic parameters of the roots were compared with those of the stem and related to anatomical traits {mean conduit diameter (d), wall reinforcement [(t/b)(2)]}. We hypothesized that temperature-related restrictions in root function would cause a progressive limitation of hydraulic efficiency and safety with increasing elevation. We found that both root k s and K R decreased from low (1600 m a.s.l.: k s 5.6 ± 0.7 kg m(-1) s(-1) MPa(-1), K R 0.049 ± 0.005 kg m(-2) s (-1) MPa(-1)) to high elevation (2100 m a.s.l.: k s 4.2 ± 0.6 kg m(-1) s(-1) MPa(-1), K R 0.035 ± 0.006 kg m(-2) s(-1) MPa(-1)), with small trees showing higher K R than large trees. k s was higher in roots than in stems (0.5 ± 0.05 kg m(-1)s(-1)MPa(-1)). Ψ 50 values were similar across elevations and overall less negative in roots (Ψ 50 -3.6 ± 0.1 MPa) than in stems (Ψ 50 -3.9 ± 0.1 MPa). In roots, large-diameter tracheids were lacking at high elevation and (t/b)(2) increased, while d did not change. The elevational decrease in root hydraulic efficiency reflects a limitation in timberline tree hydraulics. In contrast, hydraulic safety was similar across elevations, indicating that avoidance of hydraulic failure is important for timberline trees. As hydraulic patterns can only partly be explained by the anatomical parameters studied, limitations and/or adaptations at the pit level are likely.

Yoga reduces performance anxiety in adolescent musicians.

PubMed

Khalsa, Sat Bir S; Butzer, Bethany; Shorter, Stephanie M; Reinhardt, Kristen M; Cope, Stephen

2013-01-01

Professional musicians often experience high levels of stress, music performance anxiety (MPA), and performance-related musculoskeletal disorders (PRMDs). Given the fact that most professional musicians begin their musical training before the age of 12, it is important to identify interventions that will address these issues from an early age. This study intended to replicate and expand upon adult research in this area by evaluating the effects of a yoga intervention on MPA and PRMDs in a population of adolescent musicians. The present study was the first to examine these effects. The research team assigned participants, adolescent musicians, into two groups. The intervention group (n = 84) took part in a 6-wk yoga program, and the control group (n = 51) received no treatment. The team evaluated the effects of the yoga intervention by comparing the scores of the intervention group to those of the control group on a number of questionnaires related to MPA and PRMDs. The study was conducted at the Boston University Tanglewood Institute (BUTI). BUTI is a training academy for advanced adolescent musicians, located in Lenox, Massachusetts. Participants were adolescent, residential music students (mean age = 16 y) in a 6-wk summer program at the BUTI in 2007 and 2008. Participants in the yoga intervention group were requested to attend three, 60-min, Kripalustyle yoga classes each wk for 6 wk. MPA was measured using the Performance Anxiety Questionnaire (PAQ) and the Music Performance Anxiety Inventory for Adolescents (MPAI-A). PRMDs were measured using the Performance-Related Musculoskeletal Disorders Questionnaire (PRMD-Q). RESULTS • Yoga participants showed statistically significant reductions in MPA from baseline to the end of the program compared to the control group, as measured by several subscales of the PAQ and MPAI-A; however, the results for PRMDs were inconsistent. The findings suggest that yoga may be a promising way for adolescents to reduce MPA and perhaps even prevent it in the future. These findings also suggest a novel treatment modality that potentially might alleviate MPA and prevent the early disruption and termination of musical careers.

CdSe/ZnS Quantum Dots trigger DNA repair and antioxidant enzyme systems in Medicago sativa cells in suspension culture

PubMed Central

2013-01-01

Background Nanoparticles appear to be promising devices for application in the agriculture and food industries, but information regarding the response of plants to contact with nano-devices is scarce. Toxic effects may be imposed depending on the type and concentration of nanoparticle as well as time of exposure. A number of mechanisms may underlie the ability of nanoparticles to cause genotoxicity, besides the activation of ROS scavenging mechanisms. In a previous study, we showed that plant cells accumulate 3-Mercaptopropanoic acid-CdSe/ZnS quantum dots (MPA-CdSe/ZnS QD) in their cytosol and nucleus and increased production of ROS in a dose dependent manner when exposed to QD and that a concentration of 10 nM should be cyto-compatible. Results When Medicago sativa cells were exposed to 10, 50 and 100 nM MPA-CdSe/ZnS QD a correspondent increase in the activity of Superoxide dismutase, Catalase and Glutathione reductase was registered. Different versions of the COMET assay were used to assess the genotoxicity of MPA-CdSe/ZnS QD. The number of DNA single and double strand breaks increased with increasing concentrations of MPA-CdSe/ZnS QD. At the highest concentrations, tested purine bases were more oxidized than the pyrimidine ones. The transcription of the DNA repair enzymes Formamidopyrimidine DNA glycosylase, Tyrosyl-DNA phosphodiesterase I and DNA Topoisomerase I was up-regulated in the presence of increasing concentrations of MPA-CdSe/ZnS QD. Conclusions Concentrations as low as 10 nM MPA-CdSe/ZnS Quantum Dots are cytotoxic and genotoxic to plant cells, although not lethal. This sets a limit for the concentrations to be used when practical applications using nanodevices of this type on plants are being considered. This work describes for the first time the genotoxic effect of Quantum Dots in plant cells and demonstrates that both the DNA repair genes (Tdp1β, Top1β and Fpg) and the ROS scavenging mechanisms are activated when MPA-CdSe/ZnS QD contact M. sativa cells. PMID:24359290

Interaction between fed gastric media (Ensure Plus®) and different hypromellose based caffeine controlled release tablets: comparison and mechanistic study of caffeine release in fed and fasted media versus water using the USP dissolution apparatus 3.

PubMed

Franek, Frans; Holm, Per; Larsen, Frank; Steffansen, Bente

2014-01-30

The aim of the study was to investigate caffeine release in fed and fasted state media from three controlled release matrix tablets containing different HPMC viscosity grades. The biorelevant in vitro dissolution methods utilize the USP 3 dissolution apparatus and biorelevant media to simulate fed and fasted gastro-intestinal dissolution conditions. The effect of tablet reciprocation rate (dip speed) in dissolution media (10 and 15 dips per minute) and media (water, fed and fasted) on caffeine release rate from - and erosion rate of - 100, 4000 and 15,000 mPa s HPMC viscosity tablets was investigated using factorial designed experiments. Furthermore, the mechanism of release in Ensure Plus(®), a nutrition drink similar in composition to the FDA standard meal, was investigated by studying tablet swelling using texture analysis. Altering dip speed has negligible effect on release and erosion rates. Using fasted media instead of water slightly decreases caffeine release from 100 and 4000 mPa s HPMC viscosity tablets as well as erosion rates, while 15,000 mPa s tablets remain unaffected. Fed compared to fasted media decreases caffeine release rate, and the food effect is greater for the 100 mPa s viscosity tablets compared to the 4000 and 15,000 mPa s viscosity tablets. The investigation using texture analysis indicates that Ensure Plus(®) becomes rate-limiting for caffeine release from HPMC tablets by forming a hydrophobic barrier around the tablets. The barrier decreases tablet water permeation, which decreases erosion rate in 100 mPa s viscosity tablets, swelling in 15,000 mPa s viscosity tablets and caffeine release from both tablets. This observed interaction between Ensure Plus(®) and the HPMC tablets may translate into decreased drug release rate in the fed stomach, which may decrease the amount of drug available for absorption in the small intestine and thus reduce systemic drug exposure and maximum plasma concentration. Copyright © 2013 Elsevier B.V. All rights reserved.

Equation of State for Supercooled Water at Pressures up to 400 MPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Holten, Vincent; Sengers, Jan V.; Anisimov, Mikhail A., E-mail: anisimov@umd.edu

2014-12-01

An equation of state is presented for the thermodynamic properties of cold and supercooled water. It is valid for temperatures from the homogeneous ice nucleation temperature up to 300 K and for pressures up to 400 MPa, and can be extrapolated up to 1000 MPa. The equation of state is compared with experimental data for the density, expansion coefficient, isothermal compressibility, speed of sound, and heat capacity. Estimates for the accuracy of the equation are given. The melting curve of ice I is calculated from the phase-equilibrium condition between the proposed equation and an existing equation of state for icemore » I.« less

Compressive and shear properties of commercially available polyurethane foams.

PubMed

Thompson, Mark S; McCarthy, Ian D; Lidgren, Lars; Ryd, Leif

2003-10-01

The shear properties of rigid polyurethane (PU-R) foams, routinely used to simulate cancellous bone, are not well characterized. The present assessment of the shear and compressive properties of four grades of Sawbones "Rigid cellular" PU-R foam tested 20 mm gauge diameter dumb-bell specimens in torsion and under axial loading. Shear moduli ranged from 13.3 to 99.7 MPa, shear strengths from 0.7 MPa to 4.2 MPa. Compressive yield strains varied little with density while shear yield strains had peak values with "200 kgm-3" grade. PU-R foams may be used to simulate the elastic but not failure properties of cancellous bone.

Miniature microwave plasmas generated in high pressure argon

NASA Astrophysics Data System (ADS)

Inoue, Kenichi; Stauss, Sven; Kim, Jaeho; Ito, Tsuyohito; Terashima, Kazuo

2018-05-01

Miniature microwave plasmas with diameters of approximately 1 mm were generated in high-pressure argon (0.1–5.0 MPa) using a microgap electrode. The microwave power required to sustain plasmas was 1–10 W, depending on the pressure. Strong electron-neutral bremsstrahlung emission, indicating an electron temperature of approximately 12000 K, was observed at high pressures (>1 MPa), and electron densities estimated from Stark broadening revealed high values on the order of 1023 m‑3. The analysis confirmed that the coefficient for the pressure shift of the Ar I line at 696.5 nm reported by Copley and Camm can be extended to 5 MPa.

Validation of the Design Methodology for Submarines: A Comparison of Analyses and Experiments. Part 1

DTIC Science & Technology

1993-06-15

1 not only Bmat has to be determined, but also Bw.ld. - Some unknown uncertainties have been chosen, namely: - Bres(slas-tilt) has been set to 0.98...resulting in real (corrected, only Bmat -0.96 and 7nm-0.95) collapse pressures of 6.75 MPa, 6.11 MPa and 6.11 MPa respectively (errors -5.5 percent...30.78 0.96 1 .0 0.98 0.98 1 .0 1 .0 0.95 0.90 24.3 I em TNO- report Date Page B-92-1132 15 June 1993 78 SheotI Method Remarks Psubhul Bmat 8 woeld

Investigation of Shallow Undex in Littoral Ocean Domain

DTIC Science & Technology

2014-06-01

pPos Units=Pa #Units: psi, ksi, Pa, MPa, bar or scaling factor # Var=pNeg Units=Pa #Units: psi, ksi, Pa, MPa...net) # i = Impulse intensity (time in sec) # ppos = Element pressure on "positive" side (normal points toward "eye") of coupling interface

77 FR 68105 - Marine Protected Areas Federal Advisory Committee; Public Meeting

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-15

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration (NOAA) Marine Protected...), National Ocean Service (NOS), National Oceanic and Atmospheric Administration (NOAA), Department of...-3110); email: [email protected]noaa.gov ; or visit the National MPA Center Web site at http://www.mpa.gov...

Microstructures, mechanical properties, and degradation behaviors of heat-treated Mg-Sr alloys as potential biodegradable implant materials.

PubMed

Wang, Yuxiang; Tie, Di; Guan, Renguo; Wang, Ning; Shang, Yingqiu; Cui, Tong; Li, Junqiao

2018-01-01

In previous studies, Mg-Sr alloys exhibited great biocompatibility with regard to test animals, and enhanced peri-implant bone formation. The objective of the present study was to investigate the effects of heat treatments on the mechanical and corrosion properties of Mg-Sr alloys. Various heat-treated Mg-xSr (x = 0.5, 1, and 2wt%, nominal composition) alloys were prepared using homogenization and aging treatments. Mechanical tests were performed at room temperature on the as-cast, homogenized, and peak-aged alloys. As the Sr content increased, the volume fraction of Mg 17 Sr 2 phases within the as-cast alloys increased; in addition, the mechanical strength of the alloys initially increased and subsequently decreased, while the ductility decreased. Following the homogenization treatment, the mechanical strength of the alloys decreased, and the ductility increased. Nano-sized Mg 17 Sr 2 phases were re-precipitated during the aging treatment. The age-hardening response at 160°C was enhanced as the Sr content increased. Following the aging treatment, there was an increase in the mechanical strength of the alloys; however, there was a slight reduction in the ductility. Immersion tests were conducted at 37°C for 360h, using Hank's buffered salt solution (HBSS), to study the degradation behavior of the alloys. As the Sr content of the Mg-Sr alloys increased, the corrosion rate (CR) increased owing to the galvanic effect. The homogenization treatment consequently reduced the CR dramatically, and the aging treatment had a slight effect on the CR. The peak-aged Mg-1Sr (wt%) alloy exhibited the best combination of properties. The tensile yield strength (TYS), ultimate tensile strength (UTS), elongation, compressive yield strength (CYS), ultimate compressive strength (UCS), compressibility, and CR of the as-cast Mg-1Sr (wt%) alloy were 56.0MPa, 92.67MPa, 1.27%, 171.4MPa, 243.6MPa, 22.3%, and 1.76mm/year, respectively. The respective results obtained for the peak-aged Mg-1Sr (wt%) alloys were 69.7MPa, 135.6MPa, 3.22%, 183.1MPa, 273.6MPa, 27.6%, and 1.33mm/year. Following immersion in HBSS, the primary corrosion products of the peak-aged Mg-1Sr (wt%) alloy were Mg(OH) 2 , MgO, MgCO 3 , Mg 3 (PO 4 ) 2 , MgHPO 4 , and Mg(H 2 PO 4 ) 2 , which enhanced the corrosion resistance by forming a composite corrosion film. Copyright © 2017 Elsevier Ltd. All rights reserved.

Classification and characteristics of Japanese patients with antineutrophil cytoplasmic antibody-associated vasculitis in a nationwide, prospective, inception cohort study.

PubMed

Sada, Ken-ei; Yamamura, Masahiro; Harigai, Masayoshi; Fujii, Takao; Dobashi, Hiroaki; Takasaki, Yoshinari; Ito, Satoshi; Yamada, Hidehiro; Wada, Takashi; Hirahashi, Junichi; Arimura, Yoshihiro; Makino, Hirofumi

2014-04-23

We investigated the clinical and serological features of patients with antineutrophil cytoplasmic antibody (ANCA)-associated vasculitis (AAV) in Japan using data from a nationwide, prospective, inception cohort study. In total, 156 Japanese patients with newly diagnosed AAV were classified according to the European Medicines Agency (EMEA) algorithm with exploratory surrogate markers for AAV-related non-granulomatous pulmonary lesions, predefined as alveolar haemorrhage and interstitial lung disease (ILD), and their clinical and serological features were evaluated. Using the EMEA algorithm, we identified 14 patients (9.0%) with eosinophilic granulomatosis with polyangiitis (EGPA), 33 (21.2%) with granulomatosis with polyangiitis (GPA), 78 (50.0%) with microscopic polyangiitis and renal-limited vasculitis (MPA/RLV), and 31 (19.9%) with unclassifiable vasculitis. The average ages of patients with EGPA (male/female, 5/9), GPA (12/21), and MPA/RLV (35/43) and unclassifiable (9/22) were 58.0, 63.6, 71.1, and 70.6 years, respectively. Myeloperoxidase (MPO)-ANCA and proteinase-3 ANCA positivity was 50.0% and 0% for EGPA, 54.6% and 45.5% for GPA, 97.4% and 2.6% for MPA/RLV, and 93.5% and 3.2% for unclassifiable, respectively. According to the Birmingham Vasculitis Activity Score (BVAS), cutaneous (71.4%) and nervous system (92.9%) manifestations were prominent in EGPA and ear, nose, and throat manifestations (84.9%) and chest manifestations (66.7%) in GPA. Renal manifestations developed frequently in MPA/RLV (91.0%) and GPA (63.6%). The average serum creatinine levels were 0.71 mg/dL for EGPA, 1.51 mg/dL for GPA, 2.46 mg/dL for MPA/RLV, and 0.69 mg/dL for unclassifiable. The percentages of patients with ILD were 14.3% for EGPA, 9.0% for GPA, 47.4% for MPA/RLV, and 61.3% for unclassifiable. Patients with ILD (n = 61) had significantly lower BVAS (P = 0.019) with fewer ear, nose, and throat and cardiovascular manifestations than patients without ILD (n = 95). MPO-ANCA-positive MPA/RLV is the most common form of AAV in Japanese patients, and one-half of patients with GPA were positive for MPO-ANCA. ILD is an important clinical manifestation in Japanese patients with AAV. Unclassifiable vasculitis with MPO-ANCA positivity and ILD may represent a novel variant of MPA. The University Hospital Medical Information Network Clinical Trials Registry: UMIN000001648. Registered 28 February 2009.

Corneal Stromal Elasticity and Viscoelasticity Assessed by Atomic Force Microscopy after Different Cross Linking Protocols

PubMed Central

Dias, Janice; Diakonis, Vasilios F.; Lorenzo, Michael; Gonzalez, Felipe; Porras, Kevin; Douglas, Simone; Avila, Marcel; Yoo, Sonia H.; Ziebarth, Noël M.

2015-01-01

The purpose of this study was to evaluate elasticity and viscoelasticity in the anterior and deeper stromal regions of the cornea after cross linking with three different protocols using atomic force microscopy (AFM) through indentation. A total of 40 porcine corneas were used in this study and were divided into 4 groups (10 corneas per group): control (no treatment), Dresden (corneal epithelial debridement, riboflavin pretreatment for 30 minutes and a 3mw/cm2 for 30 minutes UVA irradiation), accelerated (corneal epithelial debridement, riboflavin pretreatment for 30 minutes and a 30mw/cm2 for 3 minutes UVA irradiation), and genipin (corneal epithelial debridement and submersion of anterior surface in a 1% genipin solution for 4 hours). Elasticity and viscoelasticity were quantified using AFM through indentation for all corneas, for the anterior stroma and at a depth of 200μm. For the control, Dresden, accelerated, and Genipin groups, respectively, the average Young’s modulus for the anterior stromal region was 0.60±0.58MPa, 1.58 ±1.04MPa, 0.86±0.46MPa, and 1.71±0.51MPa; the average for the 200μm stromal depth was 0.08±0.06MPa, 0.08±0.04MPa, 0.08±0.04MPa, and 0.06±0.01MPa. Corneas crosslinked with the Dresden protocol and genipin were significantly stiffer than controls (p<0.05) in the anterior region only. For the control, Dresden, Accelerated, and Genipin groups, respectively, the average calculated apparent viscosity for the anterior stroma was 88.2±43.7kPa-s, 8.3±7.1kPa-s, 8.1±2.3kPa-s, and 9.5±3.8kPa-s; the average for the 200μm stromal depth was 35.0±3.7kPa-s, 49.6±35.1kPa-s, 42.4±17.6kPa-s, and 41.8±37.6kPa-s. All crosslinking protocols resulted in a decrease in viscosity in the anterior region only (p<0.05). The effects of cross-linking seem to be limited to the anterior corneal stroma and do not extend to the deeper stromal region. Additionally, the Dresden and genipin protocols seem to produce a stiffer anterior corneal stroma when compared to the accelerated protocol. PMID:26093276

Experimental Investigation on Poro-Elasto-Plastic Behavior of the Inner Accretionary Wedge Sediments at the Nankai Subduction Zone

NASA Astrophysics Data System (ADS)

Kuo, S. T.; Kitamura, M.; Kitajima, H.

2017-12-01

The Integrated Ocean Drilling Program (IODP) Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) have installed borehole observatories to monitor the evolution of physical and hydrological properties caused by crustal deformation at various strain rates within earthquake cycles. The observatories have been installed at the base of a forearc basin above the megathrust fault (Site C0002) and near the shallow tip of the megasplay fault (Site C0010), and will be installed near the frontal thrust (Site C0006) next year. The observatory pore pressure data have shown the dynamic and post-seismic responses and are used to estimate volumetric strain (deformation) with poroelastic parameters (e.g., Wallace et al. 2016). The parameters of submarine sediments are often computed theoretically from the porosity, compressibilities of matrix, solid, and pore fluid; however, few direct constraints on core samples have been made. To investigate the poro-elasto-plastic behavior of submarine sediments, triaxial experiments with stress relaxation were conducted on the claystone cores (20% porosity) from 2185 meters below sea floor at Site C0002. Triaxial tests were conducted by applying an axial load at a constant displacement rate of 5×10-9m/s, while keeping confining pressure (Pc) at 42, 48, or 78 MPa and pore pressure (Pp) at 20 MPa. Stress relaxation tests were conducted periodically, in which neither axial displacement nor pore volume change was allowed. At lower effective pressure (Pe=Pc-Pp) of 22 and 28 MPa, the samples deform in a brittle manner, with a peak strength of 50 and 55 MPa and a residual strength of 36 and 46 MPa, respectively. At higher Pe of 58 MPa, the sample exhibits strain hardening. The relaxation tests at Pe = 22 MPa show an increase in Pp before yield and a decrease in Pp after yield, suggesting a transition from compaction to dilation. All of the relaxation tests at Pe = 58 MPa show an increase in Pp, suggesting compaction throughout the deformation. The ratio of Pp to volumetric strain determined from the relaxation tests ranges 0.4 - 2.0 kPa/μstrain and is lower than the value of 8.7 kPa/μstrain for sediments with 20% porosity computed based on the poroelasticity theory (Davis et al., 2009), implying that the volumetric strain during our relaxation tests is mainly due to plastic deformation.

Slow Crack Growth and Fracture Toughness of Sapphire for the International Space Station Fluids and Combustion Facility

NASA Technical Reports Server (NTRS)

Salem, Jonathan A.

2006-01-01

The fracture toughness, inert flexural strength, and slow crack growth parameters of the r- and a-planes of sapphire grown by the Heat Exchange Method were measured to qualify sapphire for structural use in the International Space Station. The fracture toughness in dry nitrogen, K(sub Ipb), was 2.31 +/- 0.12 MPa(square root of)m and 2.47 +/- 0.15 MPa(squre root of)m for the a- and r-planes, respectively. Fracture toughness measured in water via the operational procedure in ASTM C1421 was significantly lower, K(sub Ivb) = 1.95+/- 0.03 MPa(square root of)m, 1.94 +/- 0.07 and 1.77 +/- 0.13 MPa(square root of)m for the a- , m- and r-planes, respectively. The mean inert flexural strength in dry nitrogen was 1085 +/- 127 MPa for the r-plane and 1255 +/- 547 MPa for the a-plane. The power law slow crack growth exponent for testing in water was n = 21 +/- 4 for the r-plane and n (greater than or equal to) 31 for the a-plane. The power law slow crack growth coefficient was A = 2.81 x 10(exp -14) m/s x (MPa(squre root of)m)/n for the r-plane and A (approx. equals)2.06 x 10(exp -15) m/s x (MPa(square root of)m)/n for the a-plane. The r- and a-planes of sapphire are relatively susceptible to stress corrosion induced slow crack growth in water. However, failure occurs by competing modes of slow crack growth at long failure times and twinning for short failure time and inert environments. Slow crack growth testing needs to be performed at low failure stress levels and long failure times so that twinning does not affect the results. Some difficulty was encountered in measuring the slow crack growth parameters for the a-plane due to a short finish (i.e., insufficient material removal for elimination of the damage generated in the early grinding stages). A consistent preparation method that increases the Weibull modulus of sapphire test specimens and components is needed. This would impart higher component reliability, even if higher Weibull modulus is gained at the sacrifice of absolute strength of the component. The current specification frequently used for the preparation of sapphire test specimens and components (e.g., a "60/40" scratch-dig finish) is inadequate to avoid a short finish.

Seasonal changes of whole root system conductance by a drought-tolerant grape root system.

PubMed

Alsina, Maria Mar; Smart, David R; Bauerle, Taryn; de Herralde, Felicidad; Biel, Carme; Stockert, Christine; Negron, Claudia; Save, Robert

2011-01-01

The role of root systems in drought tolerance is a subject of very limited information compared with above-ground responses. Adjustments to the ability of roots to supply water relative to shoot transpiration demand is proposed as a major means for woody perennial plants to tolerate drought, and is often expressed as changes in the ratios of leaf to root area (A(L):A(R)). Seasonal root proliferation in a directed manner could increase the water supply function of roots independent of total root area (A(R)) and represents a mechanism whereby water supply to demand could be increased. To address this issue, seasonal root proliferation, stomatal conductance (g(s)) and whole root system hydraulic conductance (k(r)) were investigated for a drought-tolerant grape root system (Vitis berlandieri×V. rupestris cv. 1103P) and a non-drought-tolerant root system (Vitis riparia×V. rupestris cv. 101-14Mgt), upon which had been grafted the same drought-sensitive clone of Vitis vinifera cv. Merlot. Leaf water potentials (ψ(L)) for Merlot grafted onto the 1103P root system (-0.91±0.02 MPa) were +0.15 MPa higher than Merlot on 101-14Mgt (-1.06±0.03 MPa) during spring, but dropped by approximately -0.4 MPa from spring to autumn, and were significantly lower by -0.15 MPa (-1.43±0.02 MPa) than for Merlot on 101-14Mgt (at -1.28±0.02 MPa). Surprisingly, g(s) of Merlot on the drought-tolerant root system (1103P) was less down-regulated and canopies maintained evaporative fluxes ranging from 35-20 mmol vine(-1) s(-1) during the diurnal peak from spring to autumn, respectively, three times greater than those measured for Merlot on the drought-sensitive rootstock 101-14Mgt. The drought-tolerant root system grew more roots at depth during the warm summer dry period, and the whole root system conductance (k(r)) increased from 0.004 to 0.009 kg MPa(-1) s(-1) during that same time period. The changes in k(r) could not be explained by xylem anatomy or conductivity changes of individual root segments. Thus, the manner in which drought tolerance was conveyed to the drought-sensitive clone appeared to arise from deep root proliferation during the hottest and driest part of the season, rather than through changes in xylem structure, xylem density or stomatal regulation. This information can be useful to growers on a site-specific basis in selecting rootstocks for grape clonal material (scions) grafted to them.

Ultrasound-assisted green economic synthesis of hydroxyapatite nanoparticles using eggshell biowaste and study of mechanical and biological properties for orthopedic applications.

PubMed

Ingole, Vijay H; Hany Hussein, Kamal; Kashale, Anil A; Ghule, Kalyani; Vuherer, Tomaž; Kokol, Vanja; Chang, Jia-Yaw; Ling, Yong-Chien; Vinchurkar, Aruna; Dhakal, Hom N; Ghule, Anil V

2017-11-01

Nanostructured hydroxyapatite (HAp) is the most favorable candidate biomaterial for bone tissue engineering because of its bioactive and osteoconductive properties. Herein, we report for the first time ultrasound-assisted facile and economic approach for the synthesis of nanocrystalline hydroxyapatite (Ca 10 (PO 4 ) 6 (OH) 2 ) using recycled eggshell biowaste referred as EHAp. The process involves the reaction of eggshell biowaste as a source of calcium and ammonium dihydrogen orthophosphate as a phosphate source. Ultrasound-mediated chemical synthesis of hydroxyapatite (HAp) is also carried out using similar approach wherein commercially available calcium hydroxide and ammonium dihydrogen orthophosphate were used as calcium and phosphate precursors, respectively and referred as CHAp for better comparison. The prepared materials were characterized by X-ray diffraction, field emission scanning electron microscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy to determine crystal structure, particle morphology, and the presence of chemical functional groups. The nanocrystalline EHAp and CHAp were observed to have spherical morphology with uniform size distribution. Furthermore, mechanical properties such as Vickers hardness, fracture toughness, and compression tests have been studied of the EHAp and CHAp samples showing promising results. Mechanical properties show the influence of calcination at 600°C EHAp and CHAp material. After calcination, in the case of EHAp material an average hardness, mechanical strength, elastic modulus, and fracture toughness were found 552 MPa, 46.6 MPa, 2824 MPa, and 3.85 MPa m 1/2 , respectively, while in the case of CHAp 618 MPa, 47.5 MPa, 2071 MPa, and 3.13 MPa m 1/2 . In vitro cell studies revealed that the EHAp and CHAp nanoparticles significantly increased the attachment and proliferation of the hFOB cells. Here, we showed that EHAp and CHAp provide promising biocompatible materials that do not affect the cell viability and proliferation with enhancing the osteogenic activity of osteoblasts. Moreover, hFOB cells are found to express Osteocalcin, Osteopontin, Collagen I, Osteonectin, BMP-2 on the EHAp and CHAp bone graft. This study demonstrates the formation of pure nanocrystalline HAp with promising properties justifying the fact that the eggshell biowaste could be successfully used for the synthesis of HAp with good mechanical and osteogenic properties. These findings may have significant implications for designing of biomaterial for use in orthopedic tissue regeneration. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 105A: 2935-2947, 2017. © 2017 Wiley Periodicals, Inc.

Efficacy of Methylprednisolone Acetate Versus Triamcinolone Acetonide Intra-articular Knee Injection in Patients With Chronic Inflammatory Arthritis: A 24-Week Randomized Controlled Trial.

PubMed

Kumar, Ashwani; Dhir, Varun; Sharma, Shefali; Sharma, Aman; Singh, Surjit

2017-01-01

Triamcinolone hexacetonide (TH), triamcinolone acetonide (TA), and methylprednisolone acetate (MPA) are commonly used intra-articular steroid preparations. Studies suggest that intra-articular TH is more efficacious than MPA and TA in chronic inflammatory arthritis. However, it is unclear which of the latter two preparations has better efficacy. Thus, we compared intra-articular knee injections of MPA and TA in patients with chronic inflammatory arthritis. This double-blind, randomized controlled trial included patients with rheumatoid arthritis or spondyloarthritis with an acutely swollen knee joint (≥1 week, <24 weeks). They were randomly assigned (1:1) to intra-articular knee injection with MPA or TA (80 mg, 2 mL of each). Evaluations were performed at 4, 12, and 24 weeks. Primary outcome was time to relapse (Kaplan-Meier) over 24 weeks, with relapse defined as return to baseline pain or swelling ≥1 week. Secondary outcomes were change in pain and swelling (using a numerical rating scale), range of movement, and occurrence of adverse effects. Primary analysis was intention to treat, with last observation carried forward. One hundred patients (89 with rheumatoid arthritis) were randomly assigned in equal numbers to the MPA and TA groups. Nine patients relapsed in each group over 24 weeks. The mean time to relapse was not significantly different between the MPA and TA groups (20.8 [95% CI, 18.8-22.7] weeks and 20.9 [95% CI, 19.0-22.8] weeks, respectively; P = 0.9; hazard ratio = 1.0 [95% CI, 0.4-2.5]). In both groups, there was a significant decline in pain and swelling scores at all visits (P < 0.001); however, there were no significant intergroup differences. At 24 weeks, mean change in pain in the MPA (-4.4 [3.1]) and TA groups (-3.9 [2.8]) was not significantly different (P = 0.46). No infection, hematoma or hypopigmentation occurred in any patient. In addition, no significant intergroup differences were found in joint swelling, range of movement, modified (28 joint) Disease Activity Score using 3 variables, or Health Assessment Questionnaire over 24 weeks. No significant differences were found in efficacy between intra-articular knee injections with MPA and TA in these patients with chronic inflammatory arthritis. However, results need to be extrapolated cautiously because of the small sample size. Three-quarters of the patients remained relapse free at 24 weeks. Clinical Trials Registry of India (www.ctri.nic.in) identifier: CTRI/2015/09/006187. Copyright © 2017 Elsevier HS Journals, Inc. All rights reserved.

High pressure treatment changes spoilage characteristics and shelf life of Pacific oysters ( Crassostrea gigas) during refrigerated storage

NASA Astrophysics Data System (ADS)

Cao, Rong; Zhao, Ling; Liu, Qi

2017-04-01

The effects of high pressure (HP) treatment on spoilage characteristic and shelf life extension of Pacific oysters ( Crassostrea gigas) during refrigerated storage were studied. Results showed that HP treatment of 275 MPa for 3 min or 300 MPa for 2 min could achieve 100% full release of oyster adductor muscle, pressures higher than 350 MPa caused excessive release as the shells of oysters were broken, thus use of higher pressures should be cautious in oyster processing industry because of its adverse impact on the appearance of shells. HP treatment (300 MPa, 2 min) was proper for the shucking of Pacific oyster ( Crassostrea gigas) in China. This treatment caused no organoleptic disadvantage. Moreover, HP treatment resulted in obvious differences in biochemical spoilage indicators (pH, TVB-N and TBARS) changes and volatile compounds profile determined by electronic nose during storage. HP treatment (300 MPa, 2 min) also led to a reduction of aerobic bacterial count (APC) by 1.27 log cycles. Furthermore, the APC values of oysters treated by HP were always lower than those of the control samples during storage. Based on the organoleptic, biochemical and microbiological indicators, shelf life of 6-8 d for control and 12 d for HP-treated oysters could be expected. HP treatment showed great potential in oyster processing and preservation.

Evaluation of films for packaging applications in high pressure processing

NASA Astrophysics Data System (ADS)

Largeteau, A.; Angulo, I.; Coulet, J. P.; Demazeau, G.

2010-03-01

Food treatments implying high pressures used pre-packaging systems; consequently it appeared necessary to validate different packaging films able to be used in such processes. Two different packaging films from AMCOR FLEXIBLES have been evaluated: VIROFLEXAL: BOLSA 80 MICRAS, coextrusion PA/PE (20/60μm) RILTHENE: SEMI 20/60 MICRAS, laminate PA/PE (20/60μm) Three different physico-chemical characterizations have been developed for the evaluation of films behaviour after High Hydrostatic Pressure (HHP): (i) Mechanical properties (tensile strength and sealing strength), (ii) Oxygen permeability, (iii) Migration, through the contact with four food simulating liquids FSLs (water, acetic acid 3%, ethyl alcohol 10%, iso-octane). Two different pressures values (P = 400MPa and 500MPa) have been tested, with a duration of 15 min, at ambient temperature (+20°C) and only one pressure (P = 200MPa) for the experiments at low temperature (T = -20°C) with the same duration (15min). The selection of such values can be justified taking into account that experimental conditions as a temperature close to +20°C and a pressure between 400 and 500MPa are appropriated to inactivate bacteria and different others micro-organisms. Due to the efficiency of the association of hydrostatic pressure processing and low temperature (HHP/LT) [1, 2], the same films have been tested under high pressure processing (200MPa) but at negative temperature (-20°C).

Hydrostatic pressure influences HIF-2 alpha expression in chondrocytes.

PubMed

Inoue, Hiroaki; Arai, Yuji; Kishida, Tsunao; Terauchi, Ryu; Honjo, Kuniaki; Nakagawa, Shuji; Tsuchida, Shinji; Matsuki, Tomohiro; Ueshima, Keiichirou; Fujiwara, Hiroyoshi; Mazda, Osam; Kubo, Toshikazu

2015-01-05

Hypoxia-inducible factor (HIF)-2α is considered to play a major role in the progression of osteoarthritis. Recently, it was reported that pressure amplitude influences HIF-2α expression in murine endothelial cells. We examined whether hydrostatic pressure is involved in expression of HIF-2α in articular chondrocytes. Chondrocytes were cultured and stimulated by inflammation or hydrostatic pressure of 0, 5, 10, or 50 MPa. After stimulation, heat shock protein (HSP) 70, HIF-2α, nuclear factor kappa B (NF-κB), matrix metalloproteinase (MMP)-13, MMP-3, and vascular endothelial growth factor (VEGF) gene expression were evaluated. The levels of all gene expression were increased by inflammatory stress. When chondrocytes were exposed to a hydrostatic pressure of 5 MPa, HIF-2α, MMP-13, and MMP-3 gene expression increased significantly although those of HSP70 and NF-κB were not significantly different from the control group. In contrast, HIF-2α gene expression did not increase under a hydrostatic pressure of 50 MPa although HSP70 and NF-κB expression increased significantly compared to control. We considered that hydrostatic pressure of 5 MPa could regulate HIF-2α independent of NF-κB, because the level of HIF-2α gene expression increased significantly without upregulation of NF-κB expression at 5 MPa. Hydrostatic pressure may influence cartilage degeneration, inducing MMP-13 and MMP-3 expression through HIF-2α.

Effects of hydrogen fugacity and confining pressure on the interdiffusion rate of NaSi-CaAl in plagioclase

NASA Astrophysics Data System (ADS)

Yund, Richard A.; Snow, Eleanour

1989-08-01

Average? values for NaSi-CaAl interdiffusion in the compositional interval from An0 to An26 have been determined at 1000°C by the method of lamellar homogenization. At 1500 MPa confining pressure (P), ? increases 1 order of magnitude (5.0×10-21 to 4.0×10-20 m2/s) for 4 orders of magnitude increase in hydrogen fugacity (0.029, Mn3O4-Mn2O3 buffer, to 197 MPa, FeO-Fe3O4 buffer). At constant hydrogen fugacity (fH2), ? increases rapidly at low pressure and becomes nearly independent of P above 1000 MPa. (For fH2 = 0.1 MPa, ? = 2.8 × 10-22 m2/s at P = 0.1 MPa, 5.0 × 10-21 at P = 500, 1.3×10-20 at P = 1000, and 1.4×10-20 at P = 1500). The dependence of ? on increasing pressure, when a hydrogen-related species is present, is believed to be due to an increase in the concentration of the structural defect associated with increase in the hydrogen impurity. In most crustal igneous rocks, which are internally buffered near quartz-fayalite-magnetite, the dependence of ? on fH2 is relatively minor compared to the effect of confining pressure.

Stress-strain relationship of high-strength steel (HSS) reinforcing bars

NASA Astrophysics Data System (ADS)

Anggraini, Retno; Tavio, Raka, I. Gede Putu; Agustiar

2018-05-01

The introduction of High-Strength Steel (HSS) reinforcing bars in reinforced concrete members has gained much attention in recent years and led to many advantages such as construction timesaving. It is also more economical since it can reduce the amount of reinforcing steel bars used in concrete members which in turn alleviates the congestion of reinforcement. Up to present, the building codes, e.g. American Concrete Institute (ACI) 318M-14 and Standard National Indonesia (SNI) 2847:2013, still restrict the use of higher-strength steel reinforcing bars for concrete design up to Grade 420 MPa due to the possible suspected brittle behavior of concrete members. This paper evaluates the characteristics of stress-strain relationships of HSS bars if they are comparable to the characteristics of those of Grade 420 MPa. To achieve the objective of the study, a series of steel bars from various grades (420, 550, 650, and 700 MPa) was selected. Tensile tests of these steel samples were conducted under displacement-controlled mode to capture the complete stress-strain curves and particularly the post-yield response of the steel bars. The results indicate that all the steel bars tested had the actual yield strengths greater than the corresponding specified values. The stress-strain curves of HSS reinforcing bars (Grade 550, 650, and 700 MPa) performed slightly different characteristics with those of Grade 420 MPa.

Modification of fast-growing Chinese Fir wood with unsaturated polyester resin: Impregnation technology and efficiency

NASA Astrophysics Data System (ADS)

Ma, Qing; Zhao, Zijian; Yi, Songlin; Wang, Tianlong

In this study, Chinese Fir was impregnated with unsaturated polyester resin to enhance its properties. Samples 20 mm × 20 mm × 20 mm in size were split into different sections with epoxy resin and tinfoil and subjected to an impregnation experiment under various parameters. Vacuum degree was -0.04 MPa, -0.06 MPa or -0.08 MPa and vacuum duration was 15 min, 30 min, or 45 min. The results indicated that impregnation weight percent gain is linearly dependent on curing weight percent gain. Vacuum duration appears to have less influence on the curing weight percent gain than vacuum degree, and impregnation was most successful at the transverse section compared to other sections. The optimal impregnation parameters were 30 min modification under -0.08 MPa vacuum followed by 120 min at atmospheric pressure for samples 200 mm × 100 mm × 20 mm in size. Uneven distribution of weight percent gain and cracking during the curing process suggested that 30 min post-processing at -0.09 MPa vacuum was the most effective way to complete the impregnation process. The sample's bending strength and modulus of elasticity increased after impregnation treatment. Bending strength after impregnation without post-processing reached 112.85%, but reached 71.65% with vacuum-processing; modulus of elasticity improved 67.13% and 58.28% without and with post-processing, respectively.

Thiolated silicone oils as adhesive skin protectants for improved barrier function.

PubMed

Partenhauser, A; Zupančič, O; Rohrer, J; Bonengel, S; Bernkop-Schnürch, A

2016-06-01

The purpose of this study was the evaluation of thiolated silicone oil as novel skin protectant exhibiting prolonged residence time, enhanced barrier function and reinforced occlusivity. Two silicone conjugates were synthesized with mercaptopropionic acid (MPA) and thioglycolic acid (TGA) as thiol ligands. Adhesion, protection against artificial urine and water vapour permeability with both a Payne cup set-up and transepidermal water loss (TEWL) measurements on porcine skin were assessed. Silicone thiomers showed pronounced substantivity on skin with 22.1 ± 6.3% and 39.2 ± 6.7% remaining silicone after 8 h for silicone-TGA and silicone-MPA, respectively, whereas unmodified silicone oil and dimethicone were no longer detectable. In particular, silicone-MPA provided a protective shield against artificial urine penetration with less than 25% leakage within 6 h. An up to 2.5-fold improved water vapour impermeability for silicone-MPA in comparison with unmodified control was discovered with the Payne cup model. In addition, for silicone-MPA a reduced TEWL by two-thirds corresponding to non-thiolated control was determined for up to 8 h. Thiolation of silicone oil leads to enhanced skin adhesiveness and barrier function, which is a major advantage compared to commonly used silicones and might thus be a promising treatment modality for various topical applications. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Application of high pressure processing for shelf life extension of litchi fruits (Litchi chinensis cv. Bombai) during refrigerated storage.

PubMed

Kaushik, Neelima; Kaur, Barjinder P; Rao, P Srinivasa

2014-10-01

This study attempts to report the effect of high pressure processing (100, 200 and 300 MPa for 5, 10 and 15 min at 27 ± 2 ℃) on quality and shelf life extension of 'Bombai' variety peeled litchi fruits during refrigerated storage (5 ℃). High pressure processing significantly increased total colour difference, browning index, drip loss and total soluble solids, whereas pH decreased after processing. Also, ascorbic acid content significantly decreased after high pressure processing and retention of 83.5% was observed. Texture profile analysis showed that pressurization significantly affected firmness and increased cohesiveness, gumminess, springiness and chewiness of litchi fruits. Pressure-induced firming effect was observed at 100 and 200 MPa pressure. A maximum of 3.29, 3.24 and 3.77 log10 cycles reduction in aerobic mesophiles, yeast & mold and psychrotrophs count, respectively, was achieved after pressurization of 300 MPa for 10 and 15 min treatments. During storage, samples treated at 300 MPa for 10 and 15 min showed relatively minimal changes in physico-chemical attributes, textural parameters and maintained lower viable microbial counts. Treatments at 300 MPa for 10 min and 15 min were found to enhance the shelf life of litchi fruits up to 32 days as compared to 12 days of untreated during refrigerated storage (5 ℃). © The Author(s) 2013 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

High-pressure-induced interactions between milk fat globule membrane proteins and skim milk proteins in whole milk.

PubMed

Ye, A; Anema, S G; Singh, H

2004-12-01

The association of beta-lactoglobulin (beta-LG) and alpha-lactalbumin (alpha-LA) with milk fat globule membrane (MFGM), when whole milk was treated by high pressure in the range 100 to 800 MPa, was investigated using sodium dodecyl sulfate (SDS)-PAGE under reducing and nonreducing conditions. In SDS-PAGE under reducing conditions, beta-LG was observed in the MFGM material isolated from milk treated at 100 to 800 MPa for 30 min, and small amounts of alpha-LA and kappa-casein were also observed at pressures >600 MPa for 30 min. However, these proteins were not observed in SDS-PAGE under nonreducing conditions. These results indicate that beta-LG and alpha-LA associated with MFGM proteins via disulfide bonds during the high-pressure treatment of whole milk. The amount of beta-LG associated with the MFGM increased with an increase in pressure up to 800 MPa and with increasing time of pressure treatment. The maximum value for beta-LG association with the MFGM was approximately 0.75 mg/g of fat. Of the major original MFGM proteins, no change in butyrophilin was observed during the high-pressure treatment of whole milk, whereas xanthine oxidase was reduced to some extent beyond 400 MPa. In contrast to the behavior during heat treatment, PAS 6 and PAS 7 were stable during high-pressure treatment, and they remained associated with the MFGM.

Porous titanium materials with entangled wire structure for load-bearing biomedical applications.

PubMed

He, Guo; Liu, Ping; Tan, Qingbiao

2012-01-01

A kind of porous metal-entangled titanium wire material has been investigated in terms of the pore structure (size and distribution), the strength, the elastic modulus, and the mechanical behavior under uniaxial tensile loading. Its functions and potentials for surgical application have been explained. In particular, its advantages over competitors (e.g., conventional porous titanium) have been reviewed. In the study, a group of entangled titanium wire materials with non-woven structure were fabricated by using 12-180 MPa forming pressure, which have porosity in a range of 48%-82%. The pores in the materials are irregular in shape, which have a nearly half-normal distribution in size range. The yield strength, ultimate tensile strength, and elastic modulus are 75 MPa, 108 MPa, and 1.05 GPa, respectively, when its porosity is 44.7%. The mechanical properties decrease significantly as the porosity increases. When the porosity is 57.9%, these values become 24 MPa, 47.5 MPa, and 0.33 GPa, respectively. The low elastic modulus is due to the structural flexibility of the entangled titanium wire materials. For practical reference, a group of detailed data of the porous structure and the mechanical properties are reported. This kind of material is very promising for implant applications because of their very good toughness, perfect flexibility, high strength, adequate elastic modulus, and low cost. Copyright © 2011 Elsevier Ltd. All rights reserved.

MPA in Labor: Securing the Pearl Cays of Nicaragua

NASA Astrophysics Data System (ADS)

Gonzalez, Clarence; Jentoft, Svein

2011-04-01

Implementation of Marine Protected Areas (MPAs) has always a step-zero, i.e., an initial phase when the idea is incepted, communicated and negotiated among stakeholders. What happens during this phase is likely to have an impact later on. If not done right, the management of the MPA may encounter problems at later stage that will be difficult to correct. Inspired by this working theory, this article describes the effort to establish the Pearl Cays off the Caribbean coast of Nicaragua as a protected area. This case-study illustrates the critical actions to be taken during step-zero, i.e., what needs to be considered and done before an MPA is formally declared. The area investigated consists of a number of small islands (cays) and coral reefs, fishing grounds and marine turtle nesting areas. Throughout history, the cays have played an important role in sustaining livelihoods of nearby communities. Although the idea of an MPA was originally conservation, the communities saw it as an opportunity to regain ownership and control of the cays. By Nicaraguan law, in order to establish protected areas, consultation and approval from local people is required. In the case of the Pearl Cays, this has proved difficult. The article demonstrates how MPA initiatives must sometimes relate to already ongoing complex social processes in the area where they are to be instigated.

MPA in labor: securing the Pearl Cays of Nicaragua.

PubMed

Gonzalez, Clarence; Jentoft, Svein

2011-04-01

Implementation of Marine Protected Areas (MPAs) has always a step-zero, i.e., an initial phase when the idea is incepted, communicated and negotiated among stakeholders. What happens during this phase is likely to have an impact later on. If not done right, the management of the MPA may encounter problems at later stage that will be difficult to correct. Inspired by this working theory, this article describes the effort to establish the Pearl Cays off the Caribbean coast of Nicaragua as a protected area. This case-study illustrates the critical actions to be taken during step-zero, i.e., what needs to be considered and done before an MPA is formally declared. The area investigated consists of a number of small islands (cays) and coral reefs, fishing grounds and marine turtle nesting areas. Throughout history, the cays have played an important role in sustaining livelihoods of nearby communities. Although the idea of an MPA was originally conservation, the communities saw it as an opportunity to regain ownership and control of the cays. By Nicaraguan law, in order to establish protected areas, consultation and approval from local people is required. In the case of the Pearl Cays, this has proved difficult. The article demonstrates how MPA initiatives must sometimes relate to already ongoing complex social processes in the area where they are to be instigated.

In Situ Observations of Thermoreversible Gelation and Phase Separation of Agarose and Methylcellulose Solutions under High Pressure.

PubMed

Kometani, Noritsugu; Tanabe, Masahiro; Su, Lei; Yang, Kun; Nishinari, Katsuyoshi

2015-06-04

Thermoreversible sol-gel transitions of agarose and methylcellulose (MC) aqueous solutions on isobaric cooling or heating under high pressure up to 400 MPa have been investigated by in situ observations of optical transmittance and falling-ball experiments. For agarose, which undergoes the gelation on cooling, the application of pressure caused a gradual rise in the cloud-point temperature over the whole pressure range examined, which is almost consistent with the pressure dependence of gelling temperature estimated by falling-ball experiments, suggesting that agarose gel is stabilized by compression and that the gelation occurs nearly in parallel with phase separation under ambient and high-pressure conditions. For MC, which undergoes the gelation on heating, the cloud-point temperature showed a slight rise with an initial elevation of pressure up to ∼150 MPa, whereas it showed a marked depression above 200 MPa. In contrast, the gelling temperature of MC, which is nearly identical to the cloud-point temperature at ambient pressure, showed a monotonous rise with increasing pressure up to 350 MPa, which means that MC undergoes phase separation prior to gelation on heating under high pressure above 200 MPa. Similar results were obtained for the melting process of MC gel on cooling. The unique behavior of the sol-gel transition of MC under high pressure has been interpreted in terms of the destruction of hydrophobic hydration by compression.

Design and development of high frequency matrix phased-array ultrasonic probes

NASA Astrophysics Data System (ADS)

Na, Jeong K.; Spencer, Roger L.

2012-05-01

High frequency matrix phased-array (MPA) probes have been designed and developed for more accurate and repeatable assessment of weld conditions of thin sheet metals commonly used in the auto industry. Unlike the line focused ultrasonic beam generated by a linear phased-array (LPA) probe, a MPA probe can form a circular shaped focused beam in addition to the typical beam steering capabilities of phased-array probes. A CIVA based modeling and simulation method has been used to design the probes in terms of various probe parameters such as number of elements, element size, overall dimensions, frequency etc. Challenges associated with the thicknesses of thin sheet metals have been resolved by optimizing these probe design parameters. A further improvement made on the design of the MPA probe proved that a three-dimensionally shaped matrix element can provide a better performing probe at a much lower probe manufacturing cost by reducing the total number of elements and lowering the operational frequency. This three dimensional probe naturally matches to the indentation shape of the weld on the thin sheet metals and hence a wider inspection area with the same level of spatial resolution obtained by a twodimensional flat MPA probe operating at a higher frequency. The two aspects, a wider inspection area and a lower probe manufacturing cost, make this three-dimensional MPA sensor more attractive to auto manufacturers demanding a quantitative nondestructive inspection method.

Nonthermal pasteurization of fermented green table olives by means of high hydrostatic pressure processing.

PubMed

Argyri, Anthoula A; Panagou, Efstathios Z; Nychas, George-John E; Tassou, Chrysoula C

2014-01-01

Green fermented olives cv. Halkidiki were subjected to different treatments of high hydrostatic pressure (HHP) processing (400, 450, and 500 MPa for 15 or 30 min). Total viable counts, lactic acid bacteria and yeasts/moulds, and the physicochemical characteristics of the product (pH, colour, and firmness) were monitored right after the treatment and after 7 days of storage at 20(°)C to allow for recovery of injured cells. The treatments at 400 MPa for 15 and 30 min, 450 MPa for 15 and 30 min, and 500 MPa for 15 min were found insufficient as a recovery of the microbiota was observed. The treatment at 500 MPa for 30 min was effective in reducing the olive microbiota below the detection limit of the enumeration method after the treatment and after 1 week of storage and was chosen as being more appropriate for storing olives for an extended time period (5 months). After 5 months of storage at 20(°)C, no microbiota was detected in treated samples, while significant changes for both HHP treated and untreated olives were observed for colour parameters only (minor degradation). In conclusion, HHP treatment may introduce a reliable nonthermal pasteurization method to extend the microbiological shelf-life of fermented table olives.

Nonthermal Pasteurization of Fermented Green Table Olives by means of High Hydrostatic Pressure Processing

PubMed Central

Argyri, Anthoula A.; Panagou, Efstathios Z.; Nychas, George-John E.; Tassou, Chrysoula C.

2014-01-01

Green fermented olives cv. Halkidiki were subjected to different treatments of high hydrostatic pressure (HHP) processing (400, 450, and 500 MPa for 15 or 30 min). Total viable counts, lactic acid bacteria and yeasts/moulds, and the physicochemical characteristics of the product (pH, colour, and firmness) were monitored right after the treatment and after 7 days of storage at 20°C to allow for recovery of injured cells. The treatments at 400 MPa for 15 and 30 min, 450 MPa for 15 and 30 min, and 500 MPa for 15 min were found insufficient as a recovery of the microbiota was observed. The treatment at 500 MPa for 30 min was effective in reducing the olive microbiota below the detection limit of the enumeration method after the treatment and after 1 week of storage and was chosen as being more appropriate for storing olives for an extended time period (5 months). After 5 months of storage at 20°C, no microbiota was detected in treated samples, while significant changes for both HHP treated and untreated olives were observed for colour parameters only (minor degradation). In conclusion, HHP treatment may introduce a reliable nonthermal pasteurization method to extend the microbiological shelf-life of fermented table olives. PMID:25243146

Acoustic emission analysis of Vickers indentation fracture of cermet and ceramic coatings

NASA Astrophysics Data System (ADS)

Faisal, N. H.; Ahmed, R.

2011-12-01

The aim of this work was to develop an instrumented experimental methodology of quantitative material evaluation based on the acoustic emission (AE) monitoring of a dead-weight Vickers indentation. This was to assess the degree of cracking and hence the toughness of thermally sprayed coatings. AE data were acquired during indentation tests on samples of coatings of nominal thickness 250-325 µm at a variety of indentation loads ranging from 49 to 490 N. Measurements were carried out on five different carbide and ceramic coatings (HVOF as-sprayed WC-12%Co (JP5000 and JetKote), HIPed WC-12%Co (JetKote) and as-sprayed Al2O3 (APS/Metco and HVOF/theta-gun)). The raw AE signals recorded during indentation were analysed and the total surface crack length around the indent determined. The results showed that the total surface crack length measured gave fracture toughness (K1c) values which were consistent with the published literature for similar coatings but evaluated using the classical approach (Palmqvist/half-penny model). Hence, the total surface crack length criteria can be applied to ceramic and cermet coatings which may or may not exhibit fracture via radial cracks. The values of K1c measured were 3.4 ± 0.1 MPa m1/2 for high-velocity oxygen fuel (HVOF) (theta-gun) Al2O3, 4.6 ± 0.3 MPa m1/2 for as-sprayed HVOF (JetKote) WC-12%Co, 7.1±0.1 MPa m1/2 for as-sprayed HVOF (JP5000) WC-12%Co and 7.4 ± 0.2 MPa m1/2 for HIPed HVOF (JetKote) WC-12%Co coatings. The crack lengths were then calibrated against the AE response and correlation coefficients evaluated. The values of K1c measured using AE correlations were 3.3 MPa m1/2 for HVOF (theta-gun) Al2O3, 2.6 MPa m1/2 for APS (Metco) Al2O3, 2.5 MPa m1/2 for as-sprayed HVOF (JetKote) WC-12%Co, 6.3 MPa m1/2 for as-sprayed HVOF (JP5000) WC-12%Co and 8.6 MPa m1/2 for HIPed HVOF (JetKote) WC-12%Co coatings. It is concluded that within each category of coating type, AE can be used as a suitable surrogate for crack length measurement for assessing coating quality. Hence, a full measure of crack prevalence which would require time-consuming fractal dimension analysis can be made redundant for a given coating type, offering a motivation for AE-based indentation testing as a measure of quality control. Similarly, for cases where surface crack length cannot be measured due to delamination/spallation of surface, AE-based fracture toughness provides a benchmark for coating quality assessment.

Acid-base accounting to predict post-mining drainage quality on surface mines.

PubMed

Skousen, J; Simmons, J; McDonald, L M; Ziemkiewicz, P

2002-01-01

Acid-base accounting (ABA) is an analytical procedure that provides values to help assess the acid-producing and acid-neutralizing potential of overburden rocks prior to coal mining and other large-scale excavations. This procedure was developed by West Virginia University scientists during the 1960s. After the passage of laws requiring an assessment of surface mining on water quality, ABA became a preferred method to predict post-mining water quality, and permitting decisions for surface mines are largely based on the values determined by ABA. To predict the post-mining water quality, the amount of acid-producing rock is compared with the amount of acid-neutralizing rock, and a prediction of the water quality at the site (whether acid or alkaline) is obtained. We gathered geologic and geographic data for 56 mined sites in West Virginia, which allowed us to estimate total overburden amounts, and values were determined for maximum potential acidity (MPA), neutralization potential (NP), net neutralization potential (NNP), and NP to MPA ratios for each site based on ABA. These values were correlated to post-mining water quality from springs or seeps on the mined property. Overburden mass was determined by three methods, with the method used by Pennsylvania researchers showing the most accurate results for overburden mass. A poor relationship existed between MPA and post-mining water quality, NP was intermediate, and NNP and the NP to MPA ratio showed the best prediction accuracy. In this study, NNP and the NP to MPA ratio gave identical water quality prediction results. Therefore, with NP to MPA ratios, values were separated into categories: <1 should produce acid drainage, between 1 and 2 can produce either acid or alkaline water conditions, and >2 should produce alkaline water. On our 56 surface mined sites, NP to MPA ratios varied from 0.1 to 31, and six sites (11%) did not fit the expected pattern using this category approach. Two sites with ratios <1 did not produce acid drainage as predicted (the drainage was neutral), and four sites with a ratio >2 produced acid drainage when they should not have. These latter four sites were either mined very slowly, had nonrepresentative ABA data, received water from an adjacent underground mine, or had a surface mining practice that degraded the water. In general, an NP to MPA ratio of <1 produced mostly acid drainage sites, between 1 and 2 produced mostly alkaline drainage sites, while NP to MPA ratios >2 produced alkaline drainage with a few exceptions. Using these values, ABA is a good tool to assess overburden quality before surface mining and to predict post-mining drainage quality after mining. The interpretation from ABA values was correct in 50 out of 52 cases (96%), excluding the four anomalous sites, which had acid water for reasons other than overburden quality.

Effect of high-pressure processing of bovine colostrum on immunoglobulin G concentration, pathogens, viscosity, and transfer of passive immunity to calves.

PubMed

Foster, Derek M; Poulsen, Keith P; Sylvester, Hannah J; Jacob, Megan E; Casulli, Kaitlyn E; Farkas, Brian E

2016-11-01

This study aimed to determine the effects of high-pressure processing on the immunoglobulin concentration, microbial load, viscosity, and transfer of passive immunity to calves when applied to bovine colostrum as an alternative to thermal pasteurization. A pilot study using Staphylococcus aureus was conducted to determine which pressure-time treatments are most appropriate for use with bovine colostrum, with the goals of maximizing bacterial inactivation while minimizing IgG content and viscosity changes. Following the pilot study, an inoculation study was conducted in which first-milking colostrum samples from Holstein-Friesian cows were inoculated with known concentrations of various bacteria or viruses and pressure processed at either 300 MPa for up to 60min or at 400MPa for up to 30min. The recovery of total native aerobic bacteria, Escherichia coli, Salmonella enterica ssp. enterica serovar Dublin, Mycobacterium avium ssp. paratuberculosis, bovine herpesvirus type 1, and feline calicivirus were determined after processing. Colostrum IgG content was measured before and after pressure processing. Shear stress and viscosity for each treatment was determined over shear rates encompassing those found during calf feeding and at normal bovine body temperature (37.8°C). Following a calf trial, serum IgG concentration was measured in 14 calves fed 4 L of colostrum pressure processed at 400MPa for 15min. In the pilot study, S. aureus was effectively reduced with pressure treatment at 300 and 400MPa (0, 5, 10, 15, 30, and 45min), with 2 treatments at 400MPa (30, 45min) determined to be inappropriate for use with bovine colostrum due to viscosity and IgG changes. High-pressure processing at 300MPa (30, 45, and 60min) and 400MPa (10, 15, and 20min) was shown to effectively reduce total native aerobic bacteria, E. coli, Salmonella Dublin, bovine herpesvirus type 1, and feline calicivirus populations in bovine colostrum, but no decrease occurred in Mycobacterium avium ssp. paratuberculosis. All inoculation study pressure treatments insignificantly decreased IgG content of colostrum. Treatment of colostrum at 400MPa for 15min during the calf trial decreased IgG content of colostrum. Treatment at 400MPa for 15min increased colostrum viscosity, with 2 of 14 samples requiring dilution with water for calf feeding. Calves fed pressure-processed colostrum had similar serum IgG but lower efficiency of absorption than calves fed heat-treated colostrum. The results of this study suggest that high-pressure processing of bovine colostrum maintains an acceptable IgG level while decreasing bacterial and viral counts. Changes in viscosity sometimes made calf feeding more difficult, but still feasible. Additional research to optimize this technology for on-farm use is necessary. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

The MPA Capstone Course: Multifaceted Uses and Potentialities in Program Assessment

ERIC Educational Resources Information Center

Ahmed, Shamima

2015-01-01

In the United States, Master of Public Administration Program (MPA) accreditations come through fulfilling the Network of Schools of Public Policy, Affairs, and administration (NASPAA) accreditation standards. In 2009, NASPAA made some significant revisions to its accreditation standards. One of the major revisions is the requirement for programs…

Online Education in Public Affairs

ERIC Educational Resources Information Center

Ginn, Martha H.; Hammond, Augustine

2012-01-01

This exploratory study provides an overview of the current landscape of online education in the fields of Master of Public Administration and Master of Public Policy (MPA/MPP) utilizing a dataset compiled from content analysis of MPA/MPP programs' websites and survey of 96 National Association of Schools of Public Affairs and Administration…

Assessment of weld quality of aerospace grade metals by using ultrasonic matrix phased array technology

NASA Astrophysics Data System (ADS)

Na, Jeong K.; Gleeson, Sean T.

2014-03-01

Advantages of two dimensional electronic ultrasonic beam focusing, steering and scanning with the matrix phased array (MPA) technology has been used to visualize the conditions of resistance spot welds in auto vehicle grade advanced high strength steel carbon steels nondestructively. Two of the commonly used joining techniques, resistance spot welding and resistance seam welding, for thin aerospace grade plates made of aluminum, titanium, and stainless steels have also been inspected with the same MPA NDE system. In this study, a detailed discussions of the current MPA based ultrasonic real time imaging methodology has been made followed by some of the NDT results obtained with various welded test coupons.

Corrosion fatigue of Inconel 718 and Incoloy 903

NASA Technical Reports Server (NTRS)

Franklin, D. B.; Nelson, E. E.

1981-01-01

Corrosion fatigue tests were conducted on Inconel 718 and Incoloy 903 in distilled water, 500 ppm NaCl, and 3.5% NaCl. Results were compared to the endurance limit in air. For Inconel 718, the corrosion fatigue strength (CFS) IN 3.5% NaCl WAS 328 MPa or 75 percent of the endurance limit. For Incoloy 903, the CFS ranged from 234 MPa in distilled water (68 percent of the endurance limit) to 103 MPa in 3.5% NaCl (30 percent of the endurance limit). Results indicate that, for components which have limited fatigue life, an evaluation of the combined effects of fatigue and the corrosive atmosphere must be considered in projecting useful lifetimes.

The microscale evolution of the erosion front of blood clots exposed to ultrasound stimulated microbubbles.

PubMed

Acconcia, Christopher N; Leung, Ben Y C; Goertz, David E

2016-05-01

Serial two-photon microscopy of blood clots with fluorescently tagged fibrin networks was conducted during microbubble-mediated sonothrombolysis to examine the microscale evolution of the resulting erosion front. The development of a complex zonal erosion pattern was observed, comprised of a cell depleted layer of fibrin network overlying intact clot which then underwent progressive recession. The fibrin zone architecture was dependent on exposure conditions with 0.1 MPa causing no erosion, 0.39 MPa resulting in homogenous structure, and combination 0.39/0.96 MPa pulses forming large-scale tunnels. High speed imaging and Coulter counter data indicated the fibrin zone formation process involves the ejection of intact erythrocytes.

Structural Technology Evaluation Analysis Program (STEAP). Delivery Order 0025: Laser Peening for Reliable Fatigue Life

DTIC Science & Technology

2010-12-01

6 ]. Shot peening is a cold working process in which the surface of the 4 Approved for public release; distribution unlimited...for the ZA Model Parameter Value σa 945.1961MPa B 246.6467MPa β0 1.1636×10− 6 β1 0.1065 B0 1481.249 MPa εr 0.0538 α0 10− 6 α1 3.1564×10− 4 Figures 15 and...16 show the strain rate dependence curves at different strains for the JC and ZA models. 10 − 6 10 − 4 10 −2 10 0 10 2 10 4 10 6 1000 1100 1200

Fracture toughness of CIP-HIP (cold isostatic pressed - hot isostatic pressed) beryllium at elevated temperatures. Final report, 13 May 1980-13 February 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Barker, L.M.; Jones, A.H.

1986-04-01

The fracture toughness of CIP-HIP (cold isostatic pressed-hot isostatic pressed) beryllium was determined using the short-bar fracture-toughness (K/sub IcSB/) method. The K/sub IcSB/ value measured was 10.96 MPa x the square root of m at room temperature. This falls well within the expected range of 9 to 12 MPa x the square root of m as observed from previous fracture toughness measurements of beryllium. Toughness increased rapidly between 400 F and 500 F reaching a value of 16.7 MPa x the square root of m at 500 F.

Development of a Novel Catalytic Membrane Reactor for Heterogeneous Catalysis in Supercritical CO2

PubMed Central

Islam, Nazrul M.; Chatterjee, Maya; Ikushima, Yutaka; Yokoyama, Toshiro; Kawanami, Hajime

2010-01-01

A novel type of high-pressure membrane reactor has been developed for hydrogenation in supercritical carbon dioxide (scCO2). The main objectives of the design of the reactor are the separate feeding of hydrogen and substrate in scCO2 for safe reactions in a continuous flow process, and to reduce the reaction time. By using this new reactor, hydrogenation of cinnamaldehyde into hydrocinnamaldehyde has been successfully carried out with 100% selectivity at 50 °C in 10 MPa (H2: 1 MPa, CO2: 9 MPa) with a flow rate of substrate ranging from 0.05 to 1.0 mL/min. PMID:20162008

Experimental study of the seismic performance of L-shaped columns with 500 MPa steel bars.

PubMed

Wang, Tiecheng; Liu, Xiao; Zhao, Hailong

2014-01-01

Based on tests on six L-shaped RC columns with 500 MPa steel bars, the effect of axial compression ratios and stirrup spacing on failure mode, bearing capacity, displacement, and curvature ductility of the specimens is investigated. Test results show that specimens with lower axial load and large stirrup characteristic value (larger than about 0.35) are better at ductility and seismic performance, while specimens under high axial load or with a small stirrup characteristic value (less than about 0.35) are poorer at ductility; L-shaped columns with 500 MPa steel bars show better bearing capacity and ductility in comparison with specimens with HRB400 steel bars.

The Effects of Environment on the Interlaminar Shear Performance of an Oxide/Oxide Ceramic Matrix Composite at Elevated Temperature

DTIC Science & Technology

2007-06-01

of the N720/A specimen tested in creep at –4.0 MPa at 1200 °C in steam for 100 h. This specimen was unloaded, but remained at 1200°C for the...the N720/A specimen tested in creep at –4.0 MPa at 1200 °C in steam for 100 h. This specimen was unloaded, but remained at 1200°C for the duration...tested in creep at –4.0 MPa at 1200 °C in steam for 100 h. This specimen was unloaded, but remained at 1200°C for the duration of the test

Inactivation of HAV and norovirus surrogates within raw shellfish and other foods

USDA-ARS?s Scientific Manuscript database

High pressure processing can inactivate hepatitis A virus, (HAV) and the human norovirus surrogates, feline calicivirus (FCV) and murine norovirus (MNV), in foods such as oysters, strawberries, and green onions. A 5-min 400-Megapascals (MPa) treatment at 5 degrees C and a 1–min 400-MPa treatment at ...

Music Performance Anxiety among Students of the Academy in Lithuania

ERIC Educational Resources Information Center

Paliaukiene, Vilma; Kazlauskas, Evaldas; Eimontas, Jonas; Skeryte-Kazlauskiene, Monika

2018-01-01

Music performance anxiety (MPA) affects amateurs, students and professional musicians. We aimed to analyse MPA among students of music performance in a higher education academy in Lithuania. A sample of 258 music performance arts students of the Lithuanian Music and Theatre Academy participated in this study. The Kenny Music Performance Anxiety…

An Empirical Investigation of MPA Student Performance and Admissions Criteria

ERIC Educational Resources Information Center

Ragothaman, Srinivasan; Carpenter, Jon; Davies, Thomas

2009-01-01

The quality of a Master of Professional Accountancy (MPA) program, similar to other undergraduate and graduate programs in business and other disciplines, is typically directly related to the quality of its students. While there is a considerable published scholarly work on MBA student performance, there is very little research to predict student…

Dynamic Crack Branching - A Photoelastic Evaluation,

DTIC Science & Technology

1982-05-01

0.41 mPai and a 0.18 MPa, and predicted a theoretical kinking angle of 84°whichagreed well with experimentally measured angle. After crack kinking...Consistent crack branching’at KIb = 2.04 MPaI -i- and r = 1.3 mm verified this crack branching criterion. The crack branching angle predicted by--.’ DD

Mechanical Properties and Microstructure of Biomorphic Silicon Carbide Ceramics Fabricated from Wood Precursors

NASA Technical Reports Server (NTRS)

Singh, Mrityunjay; Salem, J. A.; Gray, Hugh R. (Technical Monitor)

2002-01-01

Silicon carbide based, environment friendly, biomorphic ceramics have been fabricated by the pyrolysis and infiltration of natural wood (maple and mahogany) precursors. This technology provides an eco-friendly route to advanced ceramic materials. These biomorphic silicon carbide ceramics have tailorable properties and behave like silicon carbide based materials manufactured by conventional approaches. The elastic moduli and fracture toughness of biomorphic ceramics strongly depend on the properties of starting wood preforms and the degree of molten silicon infiltration. Mechanical properties of silicon carbide ceramics fabricated from maple wood precursors indicate the flexural strengths of 3441+/-58 MPa at room temperature and 230136 MPa at 1350C. Room temperature fracture toughness of the maple based material is 2.6 +/- 0.2 MPa(square root of)m while the mahogany precursor derived ceramics show a fracture toughness of 2.0 +/- 0.2 Mpa(square root of)m. The fracture toughness and the strength increase as the density of final material increases. Fractographic characterization indicates the failure origins to be pores and chipped pockets of silicon.

Evaluation of an experimental electrohydraulic discharge device for extracorporeal shock wave lithotripsy: Pressure field of sparker array.

PubMed

Li, Guangyan; Connors, Bret A; Schaefer, Ray B; Gallagher, John J; Evan, Andrew P

2017-11-01

In this paper, an extracorporeal shock wave source composed of small ellipsoidal sparker units is described. The sparker units were arranged in an array designed to produce a coherent shock wave of sufficient strength to fracture kidney stones. The objective of this paper was to measure the acoustical output of this array of 18 individual sparker units and compare this array to commercial lithotripters. Representative waveforms acquired with a fiber-optic probe hydrophone at the geometric focus of the sparker array indicated that the sparker array produces a shock wave (P + ∼40-47 MPa, P - ∼2.5-5.0 MPa) similar to shock waves produced by a Dornier HM-3 or Dornier Compact S. The sparker array's pressure field map also appeared similar to the measurements from a HM-3 and Compact S. Compared to the HM-3, the electrohydraulic technology of the sparker array produced a more consistent SW pulse (shot-to-shot positive pressure value standard deviation of ±4.7 MPa vs ±3.3 MPa).

Determination of in situ state of stress at the Spent Fuel Test-Climax site, Climax Stock, Nevada Test Site

USGS Publications Warehouse

Ellis, W.L.; Magner, J.E.

1982-01-01

Determination of the in situ state of stress at the site of the Spent Fuel Test--Climax, using the U.S. Bureau of Mines overcore method, indicates principal stress magnitudes of 11.6 MPa, 7.1 MPa, and 2.8 MPa. The bearing and plunge of the maximum and minimum principal stress components are, respectively: N. 56? E., 29? NE; and N. 42? W., 14? NW. The vertical stress magnitude of 7.9 MPa calculated from the overcore data is significantly less than expected from overburden pressure, suggesting the stress field is influenced by local or areal geologic factors. Results from this investigation indicate (1) the stress state at the Spent Fuel Test--Climax site deviates significantly from a gravitational stress field, both in relative stress magnitudes and in orientation; (2) numerical modeling will not realistically simulate the near-field response of the Spent Fuel Test--Climax site if gravitational and (or) horizontal and vertical applied stress boundary conditions are assumed; and (3) substantial stress variations may occur spatially within the stock.

Genes Required for Growth at High Hydrostatic Pressure in Escherichia coli K-12 Identified by Genome-Wide Screening

PubMed Central

Black, S. Lucas; Dawson, Angela; Ward, F. Bruce; Allen, Rosalind J.

2013-01-01

Despite the fact that much of the global microbial biosphere is believed to exist in high pressure environments, the effects of hydrostatic pressure on microbial physiology remain poorly understood. We use a genome-wide screening approach, combined with a novel high-throughput high-pressure cell culture method, to investigate the effects of hydrostatic pressure on microbial physiology in vivo. The Keio collection of single-gene deletion mutants in Escherichia coli K-12 was screened for growth at a range of pressures from 0.1 MPa to 60 MPa. This led to the identification of 6 genes, rodZ, holC, priA, dnaT, dedD and tatC, whose products were required for growth at 30 MPa and a further 3 genes, tolB, rffT and iscS, whose products were required for growth at 40 MPa. Our results support the view that the effects of pressure on cell physiology are pleiotropic, with DNA replication, cell division, the cytoskeleton and cell envelope physiology all being potential failure points for cell physiology during growth at elevated pressure. PMID:24040140

Advanced onboard storage concepts for natural gas-fueled automotive vehicles

NASA Technical Reports Server (NTRS)

Remick, R. J.; Elkins, R. H.; Camara, E. H.; Bulicz, T.

1984-01-01

The evaluation of several advanced concepts for storing natural gas at reduced pressure is presented. The advanced concepts include adsorption on high surface area carbon, adsorption in high porosity zeolite, storage in clathration compounds, and storage by dissolution in liquid solvents. High surface area carbons with high packing density are the best low pressure storage mediums. A simple mathematical model is used to compare adsorption storage on a state of the art carbon with compression storage. The model indicates that a vehicle using adsorption storage of natural gas at 3.6 MPa will have 36 percent of the range, on the EPA city cycle, of a vehicle operating on a compression storage system having the same physical size and a peak storage pressure of 21 MPa. Preliminary experiments and current literature suggest that the storage capacity of state of the art carbons could be improved by as much as 50 percent, and that adsorption systems having a capacity equal to compression storage at 14 MPa are possible without exceeding a maximum pressure of 3.6 MPa.

Computational Fluid Dynamics Analysis of High Injection Pressure Blended Biodiesel

NASA Astrophysics Data System (ADS)

Khalid, Amir; Jaat, Norrizam; Faisal Hushim, Mohd; Manshoor, Bukhari; Zaman, Izzuddin; Sapit, Azwan; Razali, Azahari

2017-08-01

Biodiesel have great potential for substitution with petrol fuel for the purpose of achieving clean energy production and emission reduction. Among the methods that can control the combustion properties, controlling of the fuel injection conditions is one of the successful methods. The purpose of this study is to investigate the effect of high injection pressure of biodiesel blends on spray characteristics using Computational Fluid Dynamics (CFD). Injection pressure was observed at 220 MPa, 250 MPa and 280 MPa. The ambient temperature was kept held at 1050 K and ambient pressure 8 MPa in order to simulate the effect of boost pressure or turbo charger during combustion process. Computational Fluid Dynamics were used to investigate the spray characteristics of biodiesel blends such as spray penetration length, spray angle and mixture formation of fuel-air mixing. The results shows that increases of injection pressure, wider spray angle is produced by biodiesel blends and diesel fuel. The injection pressure strongly affects the mixture formation, characteristics of fuel spray, longer spray penetration length thus promotes the fuel and air mixing.

Corroboration of in vivo cartilage pressures with implications for synovial joint tribology and osteoarthritis causation.

PubMed

Morrell, Kjirste C; Hodge, W Andrew; Krebs, David E; Mann, Robert W

2005-10-11

Pressures on normal human acetabular cartilage have been collected from two implanted instrumented femoral head hemiprostheses. Despite significant differences in subjects' gender, morphology, mobility, and coordination, in vivo pressure measurements from both subjects covered similar ranges, with maximums of 5-6 MPa in gait, and as high as 18 MPa in other movements. Normalized for subject weight and height (nMPa), for free-speed walking the maximum pressure values were 25.2 for the female subject and 24.5 for the male subject. The overall maximum nMPa values were 76.2 for the female subject during rising from a chair at 11 months postoperative and 82.3 for the male subject while descending steps at 9 months postoperative. These unique in vivo data are consistent with corresponding cadaver experiments and model analyses. The collective results, in vitro data, model studies, and now corroborating in vivo data support the self-pressurizing "weeping" theory of synovial joint lubrication and provide unique information to evaluate the influence of in vivo pressure regimes on osteoarthritis causation and the efficacy of augmentations to, and substitutions for, natural cartilage.

New mechanism for toughening ceramic materials. Final report, 15 March 1989-15 July 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cutler, R.A.; Virkar, A.V.; Cross, L.E.

Ferroelastic toughening was identified as a viable mechanism for toughening ceramics. Domain structure and domain switching was identified by x-ray diffraction, transmission optical microscopy, and transmission electron microscopy in zirconia, lead zirconate titanate and gadolinium molybdata. Switching in compression was observed at stresses greater than 600 MPa and at 400 MPa in tension for polycrystalline t'-zirconia. Domain switching contributes to toughness, as evidenced by data for monoclinic zirconia, t'-zirconia, PZT and GMO. The magnitude of toughening varied between 0.6 MPa.ml/2 for GMO to 2-6 MPa-ml/2 for zirconia. Polycrystalline monoclinic and t'-zirconias, which showed no transformation toughening, had similar toughness valuesmore » as Y-TZP which exhibits transformation. Coarse-grained monoclinic and tetragonal (t') zirconia samples could be cooled to room temperature for mechanical property evaluation since fine domain size, not grain size, controlled transformation for t'-zirconia and minimized stress for m-ZrO2. LnAlO3, LnNbO4, and LnCrO3 were among the materials identified as high temperature ferroelastics.« less

Impact-induced tensional failure in rock

NASA Technical Reports Server (NTRS)

Ahrens, Thomas J.; Rubin, Allan M.

1993-01-01

Planar impact experiments were employed to induce dynamic tensile failure in Bedford limestone. Rock disks were impacted with aluminum and polymethyl methacralate flyer plates at velocities of 10 to 25 m/s. This resulted in tensile stresses in the range of 11 to 160 MPa. Tensile stress durations of 0.5 and 1.3 microsec induced microcrack growth which in many experiments were insufficient to cause complete spalling of the samples. Velocity reduction, and by inference microcrack production, occurred in samples subjected to stresses above 35 MPa in the 1.3-microsec PMMA experiments and 60 MPa in the 0.5-microsec aluminum experiments. Apparent fracture toughnesses of 2.4 and 2.5 MPa m exp 1/2 are computed for the 1.3- and 0.5-microsec experiments. Three-dimensional impact experiments were conducted on 20 cm-sized blocks of Bedford limestone and San Marcos gabbro. Compressional wave velocity deficits up to 50-60 percent were observed in the vicinity of the crater. The damage decreases as about r exp -1.5 from the crater, indicating a dependence on the magnitude and duration of the tensile pulse.

Fabrication of microporous calcite block from calcium hydroxide compact under carbon dioxide atmosphere at high temperature.

PubMed

Otsu, Akihiro; Tsuru, Kanji; Maruta, Michito; Munar, Melvin L; Matsuya, Shigeki; Ishikawa, Kunio

2012-01-01

Effects of carbonation temperature and compacting pressure on basic properties of calcite block were studied using Ca(OH)2 compact made with 0.2-2.0 MPa and their carbonation at 200-800ºC for 1 h. Microporous calcite was obtained only when carbonated at 600ºC using Ca(OH)2 compact made with 0.2 MPa even though thermogravimetry analysis showed that calcite powder was stable up to 920ºC under CO2 atmosphere. CaO formed by carbonation at 700ºC and 800ºC is thought to be caused by the limited CO2 diffusion interior to the Ca(OH)2 compact. Also, unreacted Ca(OH)2 was found for Ca(OH)2 compact prepared with 0.5 MPa or higher pressure even when carbonated at 600ºC. As a result of high temperature carbonation, crystallite size of the calcite, 58.0 nm, was significantly larger when compared to that of calcite prepared at room temperature, 35.5 nm. Porosity and diametral tensile strength of the microporous calcite were 39.5% and 6.4 MPa.

Advanced onboard storage concepts for natural gas-fueled automotive vehicles

NASA Astrophysics Data System (ADS)

Remick, R. J.; Elkins, R. H.; Camara, E. H.; Bulicz, T.

1984-06-01

The evaluation of several advanced concepts for storing natural gas at reduced pressure is presented. The advanced concepts include adsorption on high surface area carbon, adsorption in high porosity zeolite, storage in clathration compounds, and storage by dissolution in liquid solvents. High surface area carbons with high packing density are the best low pressure storage mediums. A simple mathematical model is used to compare adsorption storage on a state of the art carbon with compression storage. The model indicates that a vehicle using adsorption storage of natural gas at 3.6 MPa will have 36 percent of the range, on the EPA city cycle, of a vehicle operating on a compression storage system having the same physical size and a peak storage pressure of 21 MPa. Preliminary experiments and current literature suggest that the storage capacity of state of the art carbons could be improved by as much as 50 percent, and that adsorption systems having a capacity equal to compression storage at 14 MPa are possible without exceeding a maximum pressure of 3.6 MPa.

Strain Rate Sensitivity of Graphite/Polymer Laminate Composites

NASA Astrophysics Data System (ADS)

Syed, Izhar H.; Brar, N. S.

2002-07-01

Strain rate sensitivities of Graphite/Epoxy and Graphite/Peek laminate composites are investigated by measuring their stress-strain response at strain rates of 0.001/s, 0.1/s, and 400/s. Tension specimens of the composite laminates are fabricated in a dog-bone shape. Stress-strain data at quasi-static rates of 0.001/s and 0.1/s are obtained using a servohydraulic test system. High strain rate data are produced with a Direct Tension Split Hopkinson Bar (DTSHB). A tensile stress pulse is generated in the DTSHB by impacting a stopper flange at the end of the incident bar with an aluminum/polymeric tube launched around the incident bar. The failure (flow) tensile stress of Graphite/Epoxy increases from 240 MPa to 280±10 MPa (ɛ = 0.06) when the strain rate is raised from 0.001/s to 400/s. For Graphite/Peek, failure (flow) tension stress increases from 175 MPa at a strain rate of 0.001/s to 270±20 MPa at a strain rate of 400/s.

Effect of Solidification Behavior on Microstructures and Mechanical Properties of Ni-Cr-Fe Superalloy Investment Casting

PubMed Central

Kang, Maodong; Wang, Jun; Gao, Haiyan; Han, Yanfeng; Wang, Guoxiang; He, Shuxian

2017-01-01

The effect of solidification behavior on the microstructures and mechanical properties of Ni-Cr-Fe superalloy investment casting is given. Metallographic and image analysis have been used to quantitatively examine the microstructures’ evolution. For the parts with the thickness of 3 mm and 24 mm, the volume fraction and maximum equivalent radius of the Laves phase increases from 0.3% to 1.2%, from 11.7 μm to 23.4 μm, respectively. Meanwhile, the volume fraction and maximum equivalent radius of carbides increase from 0.3% to 0.5%, from 8.1 μm to 9.9 μm, respectively. In addition, the volume fraction of microporosity increases from 0.3% to 2.7%. As a result, the ultimate tensile strength is reduced from 1125.5 MPa to 820.9 MPa, the elongation from 13.3% to 7.7%, and the quality index from 1294.2 MPa to 954.0 MPa, respectively. A typical brittle fracture is observed on the tensile fracture. As the cooling rate decreases, the microstructures become coarser. PMID:28772611

Focused Ultrasound-Induced Neurogenesis Requires an Increase in Blood-Brain Barrier Permeability.

PubMed

Mooney, Skyler J; Shah, Kairavi; Yeung, Sharon; Burgess, Alison; Aubert, Isabelle; Hynynen, Kullervo

2016-01-01

Transcranial focused ultrasound technology used to transiently open the blood-brain barrier, is capable of stimulating hippocampal neurogenesis; however, it is not yet known what aspects of the treatment are necessary for enhanced neurogenesis to occur. The present study set out to determine whether the opening of blood-brain barrier, the specific pressure amplitudes of focused ultrasound, and/or the intravenous administration of microbubbles (phospholipid microspheres) are necessary for the enhancement of neurogenesis. Specifically, mice were exposed to burst (10ms, 1Hz burst repetition frequency) focused ultrasound at the frequency of 1.68MHz and with 0.39, 0.78, 1.56 and 3.0MPa pressure amplitudes. These treatments were also conducted with or without microbubbles, at 0.39 + 0.78MPa or 1.56 + 3.0MPa, respectively. Only focused ultrasound at the ~0.78 MPa pressure amplitude with microbubbles promoted hippocampal neurogenesis and was associated with an increase in blood-brain barrier permeability. These results suggest that focused ultrasound -mediated neurogenesis is dependent upon the opening of the blood-brain barrier.

Effects of high-pressure extruding pretreatment on MSW upgrading and hydrolysis enhancement.

PubMed

Xu, Shuang; Kong, Xin; Liu, Jianguo; Zhao, Ke; Zhao, Guangqi; Bahdolla, Amanjol

2016-12-01

High-pressure extruding (HPE) is an efficient technology used to separate municipal solid waste (MSW) into wet (biodegradable) and dry (combustible) fractions. Effects of pressure, 10, 20, 30, and 40MPa on quality upgrading of the MSW and hydrolysis of the wet fraction were examined. TS of the dry fraction increased from 48.5% to 59.4% when the extruding pressure increased from 10 to 40MPa, meanwhile the biochemical methane potential (BMP) of the wet fraction extruded under 40MPa was 674mL CH 4 /g·VS, 33% higher than that of the organic fraction of the MSW (OFMSW) control. Furthermore, in the initial stage of hydrolysis experiment, the extruded wet fractions had lower pH and higher COD, volatile fatty acids (VFAs) and COD/VFA than those of the OFMSW control. The results confirmed that HPE upgraded the MSW and enhanced hydrolysis of the wet fractions. However, high extruding pressure as 40MPa aggravated the excessive acidification of the wet fractions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Biodegradable Zein-Based Blend Films: Structural, Mechanical and Barrier Properties

PubMed Central

Filho, José Francisco Lopes

2015-01-01

Summary The effect of adding a hydrocolloid on the structural, mechanical and barrier properties of zein-based blend films is evaluated. Zein-oleic acid blend film with added xanthan gum (Z-OA-XG) showed higher water solubility (13.09%) and opacity (8.49 AU/mm) than zein-oleic acid (Z-OA) film (10.80% and 5.19 AU/mm, respectively). Furthermore, Z-OA film had greater flexibility with lower Young’s Modulus (YM=5.02 MPa) and higher elongation at break (η=10.62%); nonetheless, it was less resistant to tension (tensile strength σ=8.5 MPa) than Z-OA-XG film, which showed YM, η and σ of 6.38 MPa, 6.66% and 10.485 MPa, respectively. Both films had glossy and homogeneous structure with comparable water vapour and oxygen barrier properties around 4.39·10–11 and 1.82·10–13 g/(Pa·s·m), respectively. Based on that, xanthan gum structure influenced mainly mechanical and light barrier properties of zein-oleic acid blend films. PMID:27904368

Spectrophotometric study of the charge-transfer and ion-pair complexation of methamphetamine with some acceptors

NASA Astrophysics Data System (ADS)

Shahdousti, Parvin; Aghamohammadi, Mohammad; Alizadeh, Naader

2008-04-01

The charge-transfer (CT) complexes of methamphetamine (MPA) as a n-donor with several acceptors including bromocresolgreen (BCG), bromocresolpurple (BCP), chlorophenolred (CPR), picric acid (PIC), and 2,3-dichloro-5,6-dicyano-1,4-benzoquinone (DDQ) have been studied spectrophotometrically in chloroform solutions in order to obtain some information about their stoichiometry and stability of complexation. The oscillator strengths, transition dipole moments and resonance energy of the complex in the ground state for all complexes have been calculated. Vertical ionization potential of MPA and electron affinity of acceptors were determined by ab initio calculation. The acceptors were also used to utilize a simple and sensitive extraction-spectrophotometric method for the determination of MPA. The method is based on the formation of 1:1 ion-pair association complexes of MPA with BCG, BCP and PIC in chloroform medium. Beer's plots were obeyed in a general concentration range of 0.24-22 μg ml -1 for the investigated drug with different acceptors. The proposed methods were applied successfully for the determination of MAP in pure and abuse drug with good accuracy and precision.

Conformational fluctuations in a green fluorescent protein-like Akane family protein: a high-pressure fluorescence study at 0.1-700 MPa

NASA Astrophysics Data System (ADS)

Maeno, Akihiro; Kato, Yuko; Jimbo, Mitsuru; Amada, Kei; Mita, Hajime; Akasaka, Kazuyuki

2017-04-01

We have investigated conformational fluctuations in a new green fluorescent protein(GFP)-like protein rb-Akane found in a red-brown-colored octocoral, Scleronephthya gracillima (Kuekenthal)), with high pressure fluorescence spectroscopy at 0.1-700 MPa. Besides the green fluorescence at 510 nm, two red fluorescence peaks are observed at 590 and 629 nm, the relative intensity of which varies reversibly with pressure. The phenomenon is interpreted as representing the cis-trans isomerization of the chromophore accompanied by the conformational transition between two sub-states of the red fluorescence form of rb-Akane. The two sub-states are separated only marginally in free energy (ΔG0 = 1.9 ± 0.4 kJ mol-1), but significantly in partial molar volume (ΔV0 = -19.8 ± 1.4 ml mol-1) at 0.1 MPa (pH 7.5, 25°C). Above 500 MPa, the fluorescence at λmax 629 nm undergoes another reversible change with pressure, showing the onset of unfolding.

Effect of High Hydrostatic Pressure Combined with Moderate Heat to Inactivate Pressure-Resistant Bacteria in Water-Boiled Salted Duck.

PubMed

Ye, Keping; Feng, Yulin; Wang, Kai; Bai, Yun; Xu, Xinglian; Zhou, Guanghong

2015-06-01

The objective of this work was to study the effect of high hydrostatic pressure combined with moderate heat to inactivate pressure-resistant bacteria in water-boiled salted duck meat (WBSDM), and to establish suitable procedures to improve the quality of WBSDM. The conditions (300 MPa/60 °C, 400 MPa/60 °C, and 500 MPa/50 °C) effectively inactivated the pressure-resistant bacteria (Bacillus cereus and Staphylococcus warneri) in WBSDM. Although more pressure-resistant than S. warneri, the above treatment conditions inactivated B. cereus more than 10(7) CFU/mL in buffer, and more than 10(6) CFU/g in WBSDM, and did not cause any changes in color, texture, or moisture content of products. The interaction between pressure and temperature is a more significant factor than only pressure in inactivating both B. cereus and S. warneri, the treatment of WBSDM at 400 MPa/ 60 °C/ 10 min is the most practical condition for postprocess of WBSDM after cooking. © 2015 Institute of Food Technologists®

Hormonal Contraceptives Differentially Suppress TFV and TAF Inhibition of HIV Infection and TFV-DP in Blood and Genital Tract CD4+ T cells.

PubMed

Shen, Zheng; Rodriguez-Garcia, Marta; Patel, Mickey V; Bodwell, Jack; Kashuba, Angela D M; Wira, Charles R

2017-12-18

HIV prevention research is focused on combining antiretrovirals (ARV) and progestin contraceptives to prevent HIV infection and pregnancy. The possibility that progestins compromise ARV anti-HIV activity prompted us to evaluate the effects of progestins on tenofovir (TFV) and TFV-alafenamide (TAF) on HIV infection and intracellular TFV-diphosphate (TFV-DP) concentrations in blood and genital CD4+ T cells. Following incubation of blood CD4+ T cells with TFV or TAF, Medroxyprogesterone acetate (MPA), but not Levonorgestrel, Norethisterone or progesterone, suppressed the anti-HIV effect of TFV by reducing intracellular TFV-DP, but had no effect on TAF inhibition of infection or TFV-DP. In contrast, with genital CD4+ T cells, MPA suppressed TAF inhibition of HIV infection and lowered of TFV-DP concentrations without affecting TFV protection. These findings demonstrate that MPA selectively compromises TFV and TAF protection in blood and genital CD4+ T cells and suggests that MPA may decrease ARV protection in individuals who use ARV intermittently for prevention.

Comparison of microbiological loads and physicochemical properties of raw milk treated with single-/multiple-cycle high hydrostatic pressure and ultraviolet-C light

NASA Astrophysics Data System (ADS)

Hu, Guanglan; Zheng, Yuanrong; Wang, Danfeng; Zha, Baoping; Liu, Zhenmin; Deng, Yun

2015-07-01

The effects of ultraviolet-C radiation (UV-C, 11.8 W/m2), single-cycle and multiple-cycle high hydrostatic pressure (HHP at 200, 400 or 600 MPa) on microbial load and physicochemical quality of raw milk were evaluated. Reductions of aerobic plate count (APC) and coliform count (CC) by HHP were more than 99.9% and 98.7%, respectively. Inactivation efficiency of microorganisms increased with pressure level. At the same pressure level, two-cycle treatments caused lower APC, but did not show CC differences compared with single-cycle treatments. Reductions of APC and CC by UV-C were somewhere between 200 MPa and 400/600 MPa. Both HHP and UV-C significantly decreased lightness and increased pH, but did not change soluble solids content and thiobarbituric acid-reactive substances' values. Two 2.5 min cycles of HHP at 600 MPa caused minimum APC and CC, and maximum conductivity. Compared with HHP, UV-C markedly increased protein oxidation and reduced darkening.

Characterization of an oxide dispersion strengthened superalloy, MA-6000E, for turbine blade applications. [turbine blade

NASA Technical Reports Server (NTRS)

Kim, Y. G.; Merrick, H. F.

1979-01-01

Alloy MA 6000E was developed by the mechanical alloying process for turbine blade applications. The nominal composition of the experimental alloy is Ni-15CR-2Mo-4W-4.5Al- 2.5Ti-2Ta- .15Zr-.05C-.01B-1.1Y2O3. The 1000 hour rupture strength in the longitudinal direction is about 145 MPa at 1093 C and about 483 MPa at 760 C. The alloy displays normal three-stage creep behavior. Typically the creep elongation is 3.5% at 760 C and 2% at 1093 C. The alloy is notch ductile (K sub 1 = 3.5). The rupture properties of the alloy are not significantly degraded by thermal cycling or prior stress isothermal exposure. The alloy also has excellent longitudinal high and low cycle fatigue resistance. Limited testing indicates that MA 6000E posesses good off-axis mechanical properties. The transverse tensile elongation at 760 C is about 3%. The 100 hour transverse rupture strength is 331 MPa at 760 C and about 55 MPa at 1093 C.

In situ synthesis of bilayered gradient poly(vinyl alcohol)/hydroxyapatite composite hydrogel by directional freezing-thawing and electrophoresis method.

PubMed

Su, Cui; Su, Yunlan; Li, Zhiyong; Haq, Muhammad Abdul; Zhou, Yong; Wang, Dujin

2017-08-01

Bilayered poly(vinyl alcohol) (PVA)/hydroxyapatite (HA) composite hydrogels with anisotropic and gradient mechanical properties were prepared by the combination of directional freezing-thawing (DFT) and electrophoresis method. Firstly, PVA hydrogels with aligned channel structure were prepared by the DFT method. Then, HA nanoparticles were in situ synthesized within the PVA hydrogels via electrophoresis. By controlling the time of the electrophoresis process, a bilayered gradient hydrogel containing HA particles in only half of the gel region was obtained. The PVA/HA composite hydrogel exhibited gradient mechanical strength depending on the distance to the cathode. The gradient initial tensile modulus ranging from 0.18MPa to 0.27MPa and the gradient initial compressive modulus from 0.33MPa to 0.51MPa were achieved. The binding strength of the two regions was relatively high and no apparent internal stress or defect was observed at the boundary. The two regions of the bilayered hydrogel also showed different osteoblast cell adhesion properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Supercritical carbon dioxide (SC-CO2) extraction of essential oil from Swietenia mahagoni seeds

NASA Astrophysics Data System (ADS)

Norodin, N. S. M.; Salleh, L. M.; Hartati; Mustafa, N. M.

2016-11-01

Swietenia mahagoni (Mahogany) is a traditional plant that is rich with bioactive compounds. In this study, process parameters such as particle size, extraction time, solvent flowrate, temperature and pressure were studied on the extraction of essential oil from Swietenia mahagoni seeds by using supercritical carbon dioxide (SC-CO2) extraction. Swietenia mahagoni seeds was extracted at a pressure of 20-30 MPa and a temperature of 40-60°C. The effect of particle size on overall extraction of essential oil was done at 30 MPa and 50°C while the extraction time of essential oil at various temperatures and at a constant pressure of 30 MPa was studied. Meanwhile, the effect of flowrate CO2 was determined at the flowrate of 2, 3 and 4 ml/min. From the experimental data, the extraction time of 120 minutes, particle size of 0.5 mm, the flowrate of CO2 of 4 ml/min, at a pressure of 30 MPa and the temperature of 60°C were the best conditions to obtain the highest yield of essential oil.

Combined pressure-thermal inactivation kinetics of Bacillus amyloliquefaciens spores in egg patty mince.

PubMed

Rajan, S; Ahn, J; Balasubramaniam, V M; Yousef, A E

2006-04-01

Bacillus amyloliquefaciens is a potential surrogate for Clostridium botulinum in validation studies involving bacterial spore inactivation by pressure-assisted thermal processing. Spores of B. amyloliquefaciens Fad 82 were inoculated into egg patty mince (approximately 1.4 x 10(8) spores per g), and the product was treated with combinations of pressure (0.1 to 700 MPa) and heat (95 to 121 degrees C) in a custom-made high-pressure kinetic tester. The values for the inactivation kinetic parameter (D), temperature coefficient (zT), and pressure coefficient (zP) were determined with a linear model. Inactivation parameters from the nonlinear Weibull model also were estimated. An increase in process pressure decreased the D-value at 95, 105, and 110 degrees C; however, at 121 degrees C the contribution of pressure to spore lethality was less pronounced. The zP-value increased from 170 MPa at 95 degrees C to 332 MPa at 121 degrees C, suggesting that B. amyloliquefaciens spores became less sensitive to pressure changes at higher temperatures. Similarly, the zT-value increased from 8.2 degrees C at 0.1 MPa to 26.8 degrees C at 700 MPa, indicating that at elevated pressures, the spores were less sensitive to changes in temperature. The nonlinear Weibull model parameter b increased with increasing pressure or temperature and was inversely related to the D-value. Pressure-assisted thermal processing is a potential alternative to thermal processing for producing shelf-stable egg products.

FEM analysis of escape capsule suffered to gas explosion

NASA Astrophysics Data System (ADS)

Li, Chang-lu; Mei, Rui-bin; Li, Chang-sheng; Cai, Ban; Liu, Xiang-hua

2013-05-01

Escape capsules are new devices for underground coal mines that provide air, water, food and supplies in the event of an emergency in where miners are unable to escape. It is difficult to carry out the experiments of explosion and safety because the danger and nonrepeatability of explosion. The structure deformation and distribution of equivalent stress has been investigated under different impact pressure conditions including unimodal and bimodal loads based on the FEM and software LS-DYNA. The results show that the distribution of deformation and equivalent stress has the same trend on the same surface with the increment of explosion pressure. The deformation and stress are larger with side impact pressure compared with that of the same front impact pressure. Furthermore, the maximum equivalent stress is 246MPa and 260MPa on the front and sides of capsule with five times for national standard impact pressure 1.5MPa. Under these conditions, the deformation is less than about 9.97mm and 10.47mm, respectively. When the front impact pressure is 2.0MPa, the deformation of capsule still belongs to elasticity but the less plastic deformation occurs on the Ushape stiffening channels with the same side impact pressure. However, it is safe for capsule structure because the equivalent stress 283MPa is much less than the tensile strength. It is noted that bimodal load accelerates the capsule deformation so that it is more dangerous compared with unimodal load.

Effect of different root canal obturating materials on push-out bond strength of a fiber dowel.

PubMed

Aggarwal, Vivek; Singla, Mamta; Miglani, Sanjay; Kohli, Sarita

2012-07-01

During dowel space preparation, the instrumentation forms a thick smear layer along with sealer-occluded dentinal tubules. The purpose of this study was to evaluate the effect of different obturating materials on push-out bond strength of a fiber dowel. Fifty human uniradicular teeth were decoronated and prepared using the step-back technique. The specimens were divided into five groups on the basis of obturating materials: group I received no obturation; group II (ZOE) gutta-percha and zinc oxide eugenol sealer; group III (ZOAH) gutta-percha and AH plus sealer; group IV (GF) GuttaFlow; and group V (RE) with Resilon Epiphany system. Dowel spaces were made with manufacturer's provided drills, and a fiber dowel was luted. Horizontal slices were obtained from the middle third, and push-out bond strength (S) was evaluated. Statistical analysis was carried out using one-way ANOVA and post hoc Tukey's test. The push-out bond strength values in the control group, ZOE, ZOAH, GF, and RE were 9.303 ± 0.565 MPa, 8.859 ± 0.539 MPa, 8.356 ± 0.618 MPa, 9.635 ± 0.435 MPa, and 8.572 ± 0.256 MPa, respectively. There was no statistically significant difference between the S values of all the groups (p > 0.05). There was no effect of different tested obturating materials on the push-out bond strength of fiber dowels; however, further studies should be conducted. © 2012 by the American College of Prosthodontists.

Development of a Spring-Loaded Impact Device to Deliver Injurious Mechanical Impacts to the Articular Cartilage Surface

PubMed Central

Alexander, Peter G.; Song, Yingjie; Taboas, Juan M.; Chen, Faye H.; Melvin, Gary M.; Manner, Paul A.

2013-01-01

Objective: Traumatic impacts on the articular joint surface in vitro are known to lead to degeneration of the cartilage. The main objective of this study was to develop a spring-loaded impact device that can be used to deliver traumatic impacts of consistent magnitude and rate and to find whether impacts cause catabolic activities in articular cartilage consistent with other previously reported impact models and correlated with the development of osteoarthritic lesions. In developing the spring-loaded impactor, the operating hypothesis is that a single supraphysiologic impact to articular cartilage in vitro can affect cartilage integrity, cell viability, sulfated glycosaminoglycan and inflammatory mediator release in a dose-dependent manner. Design: Impacts of increasing force are delivered to adult bovine articular cartilage explants in confined compression. Impact parameters are correlated with tissue damage, cell viability, matrix and inflammatory mediator release, and gene expression 24 hours postimpact. Results: Nitric oxide release is first detected after 7.7 MPa impacts, whereas cell death, glycosaminoglycan release, and prostaglandin E2 release are first detected at 17 MPa. Catabolic markers increase linearly to maximal levels after ≥36 MPa impacts. Conclusions: A single supraphysiologic impact negatively affects cartilage integrity, cell viability, and GAG release in a dose-dependent manner. Our findings showed that 7 to 17 MPa impacts can induce cell death and catabolism without compromising the articular surface, whereas a 17 MPa impact is sufficient to induce increases in most common catabolic markers of osteoarthritic degeneration. PMID:26069650

No Reef Is an Island: Integrating Coral Reef Connectivity Data into the Design of Regional-Scale Marine Protected Area Networks.

PubMed

Schill, Steven R; Raber, George T; Roberts, Jason J; Treml, Eric A; Brenner, Jorge; Halpin, Patrick N

2015-01-01

We integrated coral reef connectivity data for the Caribbean and Gulf of Mexico into a conservation decision-making framework for designing a regional scale marine protected area (MPA) network that provides insight into ecological and political contexts. We used an ocean circulation model and regional coral reef data to simulate eight spawning events from 2008-2011, applying a maximum 30-day pelagic larval duration and 20% mortality rate. Coral larval dispersal patterns were analyzed between coral reefs across jurisdictional marine zones to identify spatial relationships between larval sources and destinations within countries and territories across the region. We applied our results in Marxan, a conservation planning software tool, to identify a regional coral reef MPA network design that meets conservation goals, minimizes underlying threats, and maintains coral reef connectivity. Our results suggest that approximately 77% of coral reefs identified as having a high regional connectivity value are not included in the existing MPA network. This research is unique because we quantify and report coral larval connectivity data by marine ecoregions and Exclusive Economic Zones (EZZ) and use this information to identify gaps in the current Caribbean-wide MPA network by integrating asymmetric connectivity information in Marxan to design a regional MPA network that includes important reef network connections. The identification of important reef connectivity metrics guides the selection of priority conservation areas and supports resilience at the whole system level into the future.

Welding Residual Stress Analysis and Fatigue Strength Assessment at Elevated Temperature for Multi-pass Dissimilar Material Weld Between Alloy 617 and P92 Steel

NASA Astrophysics Data System (ADS)

Lee, Juhwa; Hwang, Jeongho; Bae, Dongho

2018-03-01

In this paper, welding residual stress analysis and fatigue strength assessment were performed at elevated temperature for multi-pass dissimilar material weld between Alloy 617 and P92 steel, which are used in thermal power plant. Multi-pass welding between Alloy 617 and P92 steel was performed under optimized welding condition determined from repeated pre-test welding. In particular, for improving dissimilar material weld-ability, the buttering welding technique was applied on the P92 steel side before multi-pass welding. Welding residual stress distribution at the dissimilar material weld joint was numerically analyzed by using the finite element method, and compared with experimental results which were obtained by the hole-drilling method. Additionally, fatigue strength of dissimilar material weld joint was assessed at the room temperature (R.T), 300, 500, and 700 °C. In finite element analysis results, numerical peak values; longitudinal (410 MPa), transverse (345 MPa) were higher than those of experiments; longitudinal (298 MPa), transverse (245 MPa). There are quantitatively big differences between numerical and experimental results, due to some assumption about the thermal conductivity, specific heat, effects of enforced convection of the molten pool, dilution, and volume change during phase transformation caused by actual shield gas. The low fatigue limit at R.T, 300 °C, 500 °C and 700 °C was assessed to be 368, 276, 173 and 137 MPa respectively.

Partial Discharge Characteristics in Composite Insulation Systems with PPLP for HTS Cable

NASA Astrophysics Data System (ADS)

Kikuchi, Y.; Yamashita, K.; Kumada, A.; Hidaka, K.; Tatamidani, K.; Masuda, T.

2014-05-01

The electrical insulation system of high-temperature superconducting (HTS) cable consists of liquid nitrogen (N2(l)) and polypropylene laminated paper (PPLP). Partial discharge (PD) may occur in butt gaps of the insulation layers and its characteristics imply the insulation performance of HTS cables. N2(l) cooling system is installed in the power system and N2(l) will flow through the cables during the system operation. Filling the HTS cable with N2(l) in order to perform pre-shipment inspection is time-consuming and costly for cable manufacturers. Therefore, they are trying to find a cost effective method for pre-shipment inspections. One alternative is to use high pressure gaseous nitrogen (N2(g)) instead of N2(l). This article investigates PD characteristics such as PD inception electric field (PDIE) and PD extinction electric field (PDEE) in butt gaps of HTS cables in 0.1 to 0.3 MPa and 0.1 MPa to 1.0 MPa N2(g) environments. For assessing the surface/volume effects, PD characteristics are measured with changing the size of butt gaps. It turns out that PDIE and PDEE in N2(g) are linearly correlated with those in N2(l) at any gas pressure in our testing, and PDIE in 1.0 MPa N2(g) is almost 30% of that in 0.2 MPa It suggests that PD characteristics in N2(l) can be extrapolated from those in N2(g).

Biomechanical Characterisation of the Human Auricular Cartilages; Implications for Tissue Engineering.

PubMed

Griffin, M F; Premakumar, Y; Seifalian, A M; Szarko, M; Butler, P E M

2016-12-01

Currently, autologous cartilage provides the gold standard for auricular reconstruction. However, synthetic biomaterials offer a number of advantages for ear reconstruction including decreased donor site morbidity and earlier surgery. Critical to implant success is the material's mechanical properties as this affects biocompatibility and extrusion. The aim of this study was to determine the biomechanical properties of human auricular cartilage. Auricular cartilage from fifteen cadavers was indented with displacement of 1 mm/s and load of 300 g to obtain a Young's modulus in compression. Histological analysis of the auricle was conducted according to glycoprotein, collagen, and elastin content. The compression modulus was calculated for each part of the auricle with the tragus at 1.67 ± 0.61 MPa, antitragus 1.79 ± 0.56 MPa, concha 2.08 ± 0.70 MPa, antihelix 1.71 ± 0.63 MPa, and helix 1.41 ± 0.67 MPa. The concha showed to have a significantly greater Young's Elastic Modulus than the helix in compression (p < 0.05). The histological analysis demonstrated that the auricle has a homogenous structure in terms of chondrocyte morphology, extracellular matrix and elastin content. This study provides new information on the compressive mechanical properties and histological analysis of the human auricular cartilage, allowing surgeons to have a better understanding of suitable replacements. This study has provided a reference, by which cartilage replacements should be developed for auricular reconstruction.

Assessment of Pulmonary Artery Stiffness of Repaired Congenital Heart Disease Patients

NASA Astrophysics Data System (ADS)

Lee, Namheon; Banerjee, Rajit; Taylor, Michael; Hor, Kan

2012-10-01

Surgical correction or palliation of congenital heart disease (CHD) often requires augmenting the main pulmonary artery (MPA) with non-native material or placing a cylindrical graft. The degree to which this intervention affects PA compliance is largely unknown. In this study, the MPA stiffness characteristics were assessed by its compliance, distensibility, and pressure-strain modulus. Coregistered velocity encoded phase-contrast MRI and cardiac catheterization data were available for a cohort of repaired CHD patients (n=8) and controls (n=3). All patients were repaired with either an RV-PA conduit or a RV outflow tract patch. We measured the MPA area change by MRI and MPA pressure during the cath. The measurements were taken through or just distal to the conduit. The MPA compliance and distensibility for the patients were significantly lower than the controls: compliance (9.8±10.8 vs 28.3±7.7mm^2/mmHg, p<0.05), distensibility (2.2±1.5 vs 6.6±2.1%Area change/mmHg, p=0.05). The patients had a significantly higher pressure-strain modulus (152.3±116.4mmHg, p<0.05) than the controls (35.8±10.6mmHg). The abnormally elevated PA stiffness due to the rigidity of the conduit or patch material may cause a compliance mismatch resulting in high stress levels contributing to the observed progressive PA dilatation. This may be a factor in the progressive RV dilatation seen in this cohort of repaired CHD patients.

Applying organization science to assess the management performance of Marine Protected Areas: An exploratory study.

PubMed

Scianna, Claudia; Niccolini, Federico; Bianchi, Carlo Nike; Guidetti, Paolo

2018-06-18

Marine Protected Areas (MPAs) are important tools to achieve marine conservation and resources management goals. The management effectiveness of MPAs (the degree to which MPAs achieve their goals) is highly variable and can be affected by many MPA attributes, for example their design, enforcement and age. Another key factor possibly affecting MPA management effectiveness is the management performance, here conceived according to Horigue et al. definition (2014) as the "level of effort exerted to enhance and sustain management of MPAs". Organization Science (OS), the discipline that studies organizations, can offer a useful framework to assess and interpret MPA management performance. Using an exploratory multiple case study approach, we applied OS principles to 11 Mediterranean MPAs in order to: i) characterize several MPA organizational features; ii) assess MPA management performance (evaluated as the effort deployed in, for example, planning the future, formalizing measurable goals, and implementing specific strategies). Results show that a number of organizational features and networking attributes are highly variable among the MPAs we have studied. For instance, goals are seldom measurable and the strategy to achieve goals is not systematically pursued. Two relevant outcomes emerge from this exploratory study: i) the management performance of the MPAs considered needs considerable improvements; ii) the methods and the approach proposed could help MPAs' managers and policy makers to understand how to improve their management performance and, consequently, their effectiveness. Copyright © 2018. Published by Elsevier Ltd.

Coresidence duration and cues of maternal investment regulate sibling altruism across cultures.

PubMed

Sznycer, Daniel; De Smet, Delphine; Billingsley, Joseph; Lieberman, Debra

2016-08-01

Genetic relatedness is a fundamental determinant of social behavior across species. Over the last few decades, researchers have been investigating the proximate psychological mechanisms that enable humans to assess their genetic relatedness to others. Much of this work has focused on identifying cues that predicted relatedness in ancestral environments and examining how they regulate kin-directed behaviors. Despite progress, many basic questions remain unanswered. Here we address three of these questions. First, we examine the replicability of the effect of two association-based cues to relatedness-maternal perinatal association (MPA) and coresidence duration-on sibling-directed altruism. MPA, the observation of a newborn being cared for by one's mother, strongly signals relatedness, but is only available to the older sibling in a sib-pair. Younger siblings, to whom the MPA cue is not available, appear to fall back on the duration of their coresidence with an older sibling. Second, we determine whether the effects of MPA and coresidence duration on sibling-directed altruism obtain across cultures. Last, we explore whether paternal perinatal association (PPA) informs sibship. Data from six studies conducted in California, Hawaii, Dominica, Belgium, and Argentina support past findings regarding the role of MPA and coresidence duration as cues to siblingship. By contrast, PPA had no effect on altruism. We report on levels of altruism toward full, half, and step siblings, and discuss the role alternate cues might play in discriminating among these types of siblings. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Hydrostatic Pressure Influences HIF-2 Alpha Expression in Chondrocytes

PubMed Central

Inoue, Hiroaki; Arai, Yuji; Kishida, Tsunao; Terauchi, Ryu; Honjo, Kuniaki; Nakagawa, Shuji; Tsuchida, Shinji; Matsuki, Tomohiro; Ueshima, Keiichirou; Fujiwara, Hiroyoshi; Mazda, Osam; Kubo, Toshikazu

2015-01-01

Hypoxia-inducible factor (HIF)-2α is considered to play a major role in the progression of osteoarthritis. Recently, it was reported that pressure amplitude influences HIF-2α expression in murine endothelial cells. We examined whether hydrostatic pressure is involved in expression of HIF-2α in articular chondrocytes. Chondrocytes were cultured and stimulated by inflammation or hydrostatic pressure of 0, 5, 10, or 50 MPa. After stimulation, heat shock protein (HSP) 70, HIF-2α, nuclear factor kappa B (NF-κB), matrix metalloproteinase (MMP)-13, MMP-3, and vascular endothelial growth factor (VEGF) gene expression were evaluated. The levels of all gene expression were increased by inflammatory stress. When chondrocytes were exposed to a hydrostatic pressure of 5 MPa, HIF-2α, MMP-13, and MMP-3 gene expression increased significantly although those of HSP70 and NF-κB were not significantly different from the control group. In contrast, HIF-2α gene expression did not increase under a hydrostatic pressure of 50 MPa although HSP70 and NF-κB expression increased significantly compared to control. We considered that hydrostatic pressure of 5 MPa could regulate HIF-2α independent of NF-κB, because the level of HIF-2α gene expression increased significantly without upregulation of NF-κB expression at 5 MPa. Hydrostatic pressure may influence cartilage degeneration, inducing MMP-13 and MMP-3 expression through HIF-2α. PMID:25569085

Comparative ecophysiological measurements on the light responses, water relations and desiccation tolerance of the filmy ferns Hymenophyllum wilsonii Hook. and H. tunbrigense (L.) Smith.

PubMed

Proctor, Michael C F

2003-05-01

Chlorophyll-fluorescence and infrared gas analyser measurements show saturation of photosynthetic electron flow and CO(2) uptake at generally lower irradiances in Hymenophyllum tunbrigense than in H. wilsonii, but with wide variation in both species (63-189 micromol m(-2) s(-1) PPFD in H. tunbrigense, 129-552 micro mol m(-2) s(-1) PPFD in H. wilsonii), probably related to both site and season. Non-photochemical quenching (at 400 micromol m(-2) s(-1) PPFD) ranged from 2.1 to 8.1, with no significant difference between the species. Pressure-volume curves from thermocouple-psychrometer measurements give full-turgor osmotic potentials of approx. -1.4 MPa in both species, and indicate low apoplast fractions and high cell-wall elastic moduli. Leaves of H. tunbrigense recovered within 24 h from up to 7 d desiccation at water potentials ranging from -40 MPa (74 % relative humidity, RH) to -220 MPa (20 % RH); after 15 or 30 d, desiccation recovery was slower and less complete, and leaves were severely damaged at the highest and lowest humidities. Hymenophyllum wilsonii recovered well from up to 30 d desiccation at -114 and -220 MPa, but at -40 MPa it showed signs of damage after 15 d, and was severely damaged or killed after 30 d. Results are discussed in relation to the ecological and geographical distributions of the two species, and to the adaptive strategies of filmy ferns in general.

In vitro tensile strength of luting cements on metallic substrate.

PubMed

Orsi, Iara A; Varoli, Fernando K; Pieroni, Carlos H P; Ferreira, Marly C C G; Borie, Eduardo

2014-01-01

The aim of this study was to determine the tensile strength of crowns cemented on metallic substrate with four different types of luting agents. Twenty human maxillary molars with similar diameters were selected and prepared to receive metallic core castings (Cu-Al). After cementation and preparation the cores were measured and the area of crown's portion was calculated. The teeth were divided into four groups based on the luting agent used to cement the crowns: zinc phosphate cement; glass ionomer cement; resin cement Rely X; and resin cement Panavia F. The teeth with the crowns cemented were subjected to thermocycling and later to the tensile strength test using universal testing machine with a load cell of 200 kgf and a crosshead speed of 0.5 mm/min. The load required to dislodge the crowns was recorded and converted to MPa/mm(2). Data were subjected to Kruskal-Wallis analysis with a significance level of 1%. Panavia F showed significantly higher retention in core casts (3.067 MPa/mm(2)), when compared with the other cements. Rely X showed a mean retention value of 1.877 MPa/mm(2) and the zinc phosphate cement with 1.155 MPa/mm(2). Glass ionomer cement (0.884 MPa/mm(2)) exhibited the lowest tensile strength value. Crowns cemented with Panavia F on cast metallic posts and cores presented higher tensile strength. The glass ionomer cement showed the lowest tensile strength among all the cements studied.

Phase-equilibrium geobarometers for silicic rocks based on rhyolite-MELTS. Part 4: Plagioclase, orthopyroxene, clinopyroxene, glass geobarometer, and application to Mt. Ruapehu, New Zealand

NASA Astrophysics Data System (ADS)

Harmon, Lydia J.; Cowlyn, James; Gualda, Guilherme A. R.; Ghiorso, Mark S.

2018-01-01

A new phase equilibria geobarometer determines magmatic storage and crystallization conditions, including pressure, temperature, oxygen fugacity ({f_{{{o}_2}}}), and the presence of a fluid phase for glass-bearing rocks containing the assemblage plagioclase + pyroxene(s). This newly developed geobarometer can better constrain crystallization conditions of shallow (< 500 MPa; < 20 km), glass-bearing andesites to dacites. The geobarometer utilizes rhyolite-MELTS to determine crystallization conditions in natural pumice and scoria samples. The validity of the geobarometer is tested by comparing it to results from experiments. Uncertainties are assessed using Monte Carlo simulations. We apply the geobarometer to the plag + opx + cpx-bearing system of Mt. Ruapehu, in the southern Taupo Volcanic Zone, New Zealand. The samples from Mt. Ruapehu are tested from 5 to 400 MPa and from super-liquidus to 90% crystalline ( 1200 to 700 °C). Mt. Ruapehu serves as a methodological testing ground for the geobarometer, and results from our geobarometer agree with recent Mt. Ruapehu studies. Results show a distribution of crystallization pressures ranging from 50 to 150 MPa ( 2.0 to 5.9 km) for different eruptions, with modes of 110 MPa ( 4.3 km) and 130 MPa ( 5.1 km). These are consistent with field interpretations of different eruptive styles based on juvenile clast textures and previous knowledge of the magma plumbing system. Mt. Ruapehu magmas are fluid saturated, with {f_{{{o}_2}}} of ΔQFM + 1 (NNO).

Precipitation of alacranite (As8S9) by a novel As(V)-respiring anaerobe strain MPA-C3.

PubMed

Mumford, Adam C; Yee, Nathan; Young, Lily Y

2013-10-01

Strain MPA-C3 was isolated by incubating arsenic-bearing sediments under anaerobic, mesophilic conditions in minimal media with acetate as the sole source of energy and carbon, and As(V) as the sole electron acceptor. Following growth and the respiratory reduction of As(V) to As(III), a yellow precipitate formed in active cultures, while no precipitate was observed in autoclaved controls, or in uninoculated media supplemented with As(III). The precipitate was identified by X-ray diffraction as alacranite, As8 S9 , a mineral previously only identified in hydrothermal environments. Sequencing of the 16S rRNA gene indicated that strain MPA-C3 is a member of the Deferribacteres family, with relatively low (90%) identity to Denitrovibrio acetiphilus DSM 12809. The arsenate respiratory reductase gene, arrA, was sequenced, showing high homology to the arrA gene of Desulfitobacterium halfniense. In addition to As(V), strain MPA-C3 utilizes NO3(-), Se(VI), Se(IV), fumarate and Fe(III) as electron acceptors, and acetate, pyruvate, fructose and benzoate as sources of carbon and energy. Analysis of a draft genome sequence revealed multiple pathways for respiration and carbon utilization. The results of this work demonstrate that alacranite, a mineral previously thought to be formed only chemically under hydrothermal conditions, is precipitated under mesophilic conditions by the metabolically versatile strain MPA-C3. © 2013 John Wiley & Sons Ltd and Society for Applied Microbiology.

The Strengthening Effect of Ice on Two Extraterrestrial Analogs: A Cautionary Tale

NASA Astrophysics Data System (ADS)

Atkinson, J.; Durham, W. B.; Seager, S.

2016-12-01

Sample retrieval from extraterrestrial bodies and in situ resource utilization (ISRU) activities have been identified as some of the most important scientific endeavors of the coming decade. With the failure of Rosetta's Philae lander to penetrate the surface of comet 67P and obtain a sample due to the high compressive strength of the surface, it is becoming obvious that knowledge of the mechanical properties of materials that might be encountered in such environments and under such conditions is critical to future mission success. Two comet/asteroid analogs (Indiana limestone and Bishop tuff), selected based on their contrasting mechanical properties and porosities, were tested under constant displacement to failure (in most cases) at low temperatures (295 K to 77 K) and low confining pressures (1 to 5 MPa). The compressive strength of both materials was determined under varied conditions of saturation, from oven-dried ( 0% water content) to fully saturated, and both brittle and ductile behavior was observed. The saturated limestone increased in strength from 30 MPa (at 295 K) to >200 MPa (at 77 K), while the Bishop tuff increased in strength from 13 MPa at 295 K to 165 MPa at 150 K. The results of this study will be useful to future sample retrieval missions or ISRU maneuvers. The large increase in compressive strength of these saturated materials at cryogenic temperatures means that future missions will need to prepare technology that has the energetic and mechanical capability to penetrate very hard substrates as they are likely to encounter.

Isochoric p-{rho}-T measurements on 1,1-difluoroethane (R152a) from 158 to 400 K and 1,1,1-trifluoroethane (R143a) from 166 to 400 K at pressures to 35 MPa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Magee, J.W.

1998-09-01

The p-{rho}-T relationships have been measured for 1,1-difluoroethane (R152a) and 1,1,1-trifluoroethane (R143a) by an isochoric method with gravimetric determinations of the amount of substance. Temperatures ranged from 158 to 400K for R152a and from 166 to 400 K for R143a, while pressures were up to 35 MPa. Measurements were conducted on compressed liquid samples. Determinations of saturated liquid densities were made by extrapolating each isochore to the vapor pressure, and determining the temperature and density at the intersection. Published p-{rho}-T data are in good agreement with this study. For the p-{rho}-T apparatus, the uncertainty of the temperature is {+-}0.03 K,more » and for pressure it is {+-}0.01% at p > 3 MPa and {+-}0.05% at p > 3 MPa and {+-}0.05% at p < 3MPa. The principal source of uncertainty is the cell volume ({approximately}28.5 cm{sup 3}), which has a standard uncertainty of {+-}0.003 cm{sup 3}. When all components of experimental uncertainty are considered, the expanded relative uncertainty (with a coverage factor k = 2 and thus a two-standard deviation estimate) of the density measurement is estimated to be {+-}0.05%.« less

Welding Residual Stress Analysis and Fatigue Strength Assessment at Elevated Temperature for Multi-pass Dissimilar Material Weld Between Alloy 617 and P92 Steel

NASA Astrophysics Data System (ADS)

Lee, Juhwa; Hwang, Jeongho; Bae, Dongho

2018-07-01

In this paper, welding residual stress analysis and fatigue strength assessment were performed at elevated temperature for multi-pass dissimilar material weld between Alloy 617 and P92 steel, which are used in thermal power plant. Multi-pass welding between Alloy 617 and P92 steel was performed under optimized welding condition determined from repeated pre-test welding. In particular, for improving dissimilar material weld-ability, the buttering welding technique was applied on the P92 steel side before multi-pass welding. Welding residual stress distribution at the dissimilar material weld joint was numerically analyzed by using the finite element method, and compared with experimental results which were obtained by the hole-drilling method. Additionally, fatigue strength of dissimilar material weld joint was assessed at the room temperature (R.T), 300, 500, and 700 °C. In finite element analysis results, numerical peak values; longitudinal (410 MPa), transverse (345 MPa) were higher than those of experiments; longitudinal (298 MPa), transverse (245 MPa). There are quantitatively big differences between numerical and experimental results, due to some assumption about the thermal conductivity, specific heat, effects of enforced convection of the molten pool, dilution, and volume change during phase transformation caused by actual shield gas. The low fatigue limit at R.T, 300 °C, 500 °C and 700 °C was assessed to be 368, 276, 173 and 137 MPa respectively.

Inactivation of Geobacillus stearothermophilus Spores by High-Pressure Carbon Dioxide Treatment

PubMed Central

Watanabe, Taisuke; Furukawa, Soichi; Hirata, Junichi; Koyama, Tetsuya; Ogihara, Hirokazu; Yamasaki, Makari

2003-01-01

High-pressure CO2 treatment has been studied as a promising method for inactivating bacterial spores. In the present study, we compared this method with other sterilization techniques, including heat and pressure treatment. Spores of Bacillus coagulans, Bacillus subtilis, Bacillus cereus, Bacillus licheniformis, and Geobacillus stearothermophilus were subjected to CO2 treatment at 30 MPa and 35°C, to high-hydrostatic-pressure treatment at 200 MPa and 65°C, or to heat treatment at 0.1 MPa and 85°C. All of the bacterial spores except the G. stearothermophilus spores were easily inactivated by the heat treatment. The highly heat- and pressure-resistant spores of G. stearothermophilus were not the most resistant to CO2 treatment. We also investigated the influence of temperature on CO2 inactivation of G. stearothermophilus. Treatment with CO2 and 30 MPa of pressure at 95°C for 120 min resulted in 5-log-order spore inactivation, whereas heat treatment at 95°C for 120 min and high-hydrostatic-pressure treatment at 30 MPa and 95°C for 120 min had little effect. The activation energy required for CO2 treatment of G. stearothermophilus spores was lower than the activation energy for heat or pressure treatment. Although heat was not necessary for inactivationby CO2 treatment of G. stearothermophilus spores, CO2 treatment at 95°C was more effective than treatment at 95°C alone. PMID:14660357

Inactivation of Geobacillus stearothermophilus spores by high-pressure carbon dioxide treatment.

PubMed

Watanabe, Taisuke; Furukawa, Soichi; Hirata, Junichi; Koyama, Tetsuya; Ogihara, Hirokazu; Yamasaki, Makari

2003-12-01

High-pressure CO2 treatment has been studied as a promising method for inactivating bacterial spores. In the present study, we compared this method with other sterilization techniques, including heat and pressure treatment. Spores of Bacillus coagulans, Bacillus subtilis, Bacillus cereus, Bacillus licheniformis, and Geobacillus stearothermophilus were subjected to CO2 treatment at 30 MPa and 35 degrees C, to high-hydrostatic-pressure treatment at 200 MPa and 65 degrees C, or to heat treatment at 0.1 MPa and 85 degrees C. All of the bacterial spores except the G. stearothermophilus spores were easily inactivated by the heat treatment. The highly heat- and pressure-resistant spores of G. stearothermophilus were not the most resistant to CO2 treatment. We also investigated the influence of temperature on CO2 inactivation of G. stearothermophilus. Treatment with CO2 and 30 MPa of pressure at 95 degrees C for 120 min resulted in 5-log-order spore inactivation, whereas heat treatment at 95 degrees C for 120 min and high-hydrostatic-pressure treatment at 30 MPa and 95 degrees C for 120 min had little effect. The activation energy required for CO2 treatment of G. stearothermophilus spores was lower than the activation energy for heat or pressure treatment. Although heat was not necessary for inactivationby CO2 treatment of G. stearothermophilus spores, CO2 treatment at 95 degrees C was more effective than treatment at 95 degrees C alone.

The hydraulic architecture of Juniperus communis L. ssp. communis: shrubs and trees compared.

PubMed

Beikircher, Barbara; Mayr, Stefan

2008-11-01

Juniperus communis ssp. communis can grow like a shrub or it can develop a tree-like habit. In this study, the hydraulic architecture of these contrasting growth forms was compared. We analysed the hydraulic efficiency (leaf-specific conductivity, k(l); specific conductivity, k(s); Huber value, HV) and the vulnerability to cavitation (the water potential corresponding to a 50% loss of conductivity, Psi(50)), as well as anatomical parameters [mean tracheid diameter, d; mean hydraulic diameter, d(h); cell wall reinforcement (t/b)(h)(2)] of shrub shoots, tree stems and tree branches. Shrub shoots were similar to tree branches (especially to lower branches) in growth form and conductivity (k(l) = 1.93 +/- 0.11 m(2) s(-1) MPa(-1) 10(-7), k(s) = 5.71 +/- 0.19 m(2) s(-1) MPa(-1) 10(-4)), but were similar to tree stems in their vulnerability to cavitation (Psi(50) = -5.81 +/- 0.08 MPa). Tree stems showed extraordinarily high k(l) and k(s) values, and HV increased from the base up. Stem xylem was more vulnerable to cavitation than branch xylem, where Psi(50) increased from lower (Psi(50) = -6.44 +/- 0.19 MPa) to upper branches (Psi(50) = -5.98 +/- 0.13 MPa). Conduit diameters were correlated with k(l) and k(s). Data indicate that differences in hydraulic architecture correspond to changes in growth form. In some aspects, the xylem hydraulics of tree-like Juniperus communis differs from that of other coniferous tree species.

No Reef Is an Island: Integrating Coral Reef Connectivity Data into the Design of Regional-Scale Marine Protected Area Networks

PubMed Central

Schill, Steven R.; Raber, George T.; Roberts, Jason J.; Treml, Eric A.; Brenner, Jorge; Halpin, Patrick N.

2015-01-01

We integrated coral reef connectivity data for the Caribbean and Gulf of Mexico into a conservation decision-making framework for designing a regional scale marine protected area (MPA) network that provides insight into ecological and political contexts. We used an ocean circulation model and regional coral reef data to simulate eight spawning events from 2008–2011, applying a maximum 30-day pelagic larval duration and 20% mortality rate. Coral larval dispersal patterns were analyzed between coral reefs across jurisdictional marine zones to identify spatial relationships between larval sources and destinations within countries and territories across the region. We applied our results in Marxan, a conservation planning software tool, to identify a regional coral reef MPA network design that meets conservation goals, minimizes underlying threats, and maintains coral reef connectivity. Our results suggest that approximately 77% of coral reefs identified as having a high regional connectivity value are not included in the existing MPA network. This research is unique because we quantify and report coral larval connectivity data by marine ecoregions and Exclusive Economic Zones (EZZ) and use this information to identify gaps in the current Caribbean-wide MPA network by integrating asymmetric connectivity information in Marxan to design a regional MPA network that includes important reef network connections. The identification of important reef connectivity metrics guides the selection of priority conservation areas and supports resilience at the whole system level into the future. PMID:26641083

Reversal of reflex pulmonary vasoconstriction induced by main pulmonary arterial distension.

PubMed

Juratsch, C E; Grover, R F; Rose, C E; Reeves, J T; Walby, W F; Laks, M M

1985-04-01

Distension of the main pulmonary artery (MPA) induces pulmonary hypertension, most probably by neurogenic reflex pulmonary vasoconstriction, although constriction of the pulmonary vessels has not actually been demonstrated. In previous studies in dogs with increased pulmonary vascular resistance produced by airway hypoxia, exogenous arachidonic acid has led to the production of pulmonary vasodilator prostaglandins. Hence, in the present study, we investigated the effect of arachidonic acid in seven intact anesthetized dogs after pulmonary vascular resistance was increased by MPA distention. After steady-state pulmonary hypertension was established, arachidonic acid (1.0 mg/min) was infused into the right ventricle for 16 min; 15-20 min later a 16-mg bolus of arachidonic acid was injected. MPA distension was maintained throughout the study. Although the infusion of arachidonic acid significantly lowered the elevated pulmonary vascular resistance induced by MPA distension, the pulmonary vascular resistance returned to control levels only after the bolus injection of arachidonic acid. Notably, the bolus injection caused a biphasic response which first increased the pulmonary vascular resistance transiently before lowering it to control levels. In dogs with resting levels of pulmonary vascular resistance, administration of arachidonic acid in the same manner did not alter the pulmonary vascular resistance. It is concluded that MPA distension does indeed cause reflex pulmonary vasoconstriction which can be reversed by vasodilator metabolites of arachidonic acid. Even though this reflex may help maintain high pulmonary vascular resistance in the fetus, its function in the adult is obscure.

Effect of surface treatment on bond strength between an indirect composite material and a zirconia framework.

PubMed

Komine, Futoshi; Fushiki, Ryosuke; Koizuka, Mai; Taguchi, Kohei; Kamio, Shingo; Matsumura, Hideo

2012-03-01

The present study evaluated the effect of various surface treatments for zirconia ceramics on shear bond strength between an indirect composite material and zirconia ceramics. In addition, we investigated the durability of shear bond strength by using artificial aging (20,000 thermocycles). A total of 176 Katana zirconia disks were randomly divided into eight groups according to surface treatment, as follows: group CON (as-milled); group GRD (wet-ground with 600-grit silicon carbide abrasive paper); groups 0.05, 0.1, 0.2, 0.4, and 0.6 MPa (airborne-particle abrasion at 0.05, 0.1, 0.2, 0.4, and 0.6 MPa, respectively); and group HF (9.5% hydrofluoric acid etching). Shear bond strength was measured at 0 thermocycles in half the specimens after 24-h immersion. The remaining specimens were subjected to 20,000 thermocycles before shear bond strength testing. Among the eight groups, the 0.1, 0.2, 0.4, and 0.6 MPa airborne-particle abraded groups had significantly higher bond strengths before and after thermocycling. The Mann-Whitney U-test revealed no significant difference in shear bond strength between 0 and 20,000 thermocycles, except in the 0.2 MPa group (P = 0.013). From the results of this study, use of airborne-particle abrasion at a pressure of 0.1 MPa or higher increases initial and durable bond strength between an indirect composite material and zirconia ceramics.

Potential application of high hydrostatic pressure to eliminate Escherichia coli O157:H7 on alfalfa sprouted seeds.

PubMed

Neetoo, Hudaa; Ye, Mu; Chen, Haiqiang

2008-12-10

Sprouts eaten raw are increasingly being perceived as hazardous foods as they have been implicated in Escherichia coli O157:H7 outbreaks where the seeds were found to be the likely source of contamination. The objective of our study was to evaluate the potential of using high hydrostatic pressure (HHP) technology for alfalfa seed decontamination. Alfalfa seeds inoculated with a cocktail of five strains of E. coli O157:H7 were subjected to pressures of 500 and 600 MPa for 2 min at 20 degrees C in a dry or wet (immersed in water) state. Immersing seeds in water during pressurization considerably enhanced inactivation of E. coli O157:H7 achieving reductions of 3.5 log and 5.7 log at 500 and 600 MPa, respectively. When dry seeds were pressurized, both pressure levels reduced the counts by <0.7 log. To test the efficacy of HHP to completely decontaminate seeds whilst meeting the FDA requirement of 5 log reductions, seeds inoculated with a ~5 log CFU/g of E. coli O157:H7 were pressure-treated at 600 and 650 MPa at 20 degrees C for holding times of 2 to 20 min. A >5 log reduction in the population was achieved when 600 MPa was applied for durations of > or =6 min although survivors were still detected by enrichment. When the pressure was stepped up to 650 MPa, the threshold time required to achieve complete elimination was 15 min. Un-inoculated seeds pressure-treated at 650 MPa for 15 min at 20 degrees C successfully sprouted achieving a germination rate identical to untreated seeds after eight days of sprouting. These results therefore demonstrate the promising application of HHP on alfalfa seeds to eliminate the risk of E. coli O157:H7 infections associated with consumption of raw alfalfa sprouts.

Transport and release of colloidal 3-mercaptopropionic acid-coated CdSe–CdS/ZnS core-multishell quantum dots in human umbilical vein endothelial cells

PubMed Central

Fontana, Jacopo M; Yin, Huijuan; Chen, Yun; Florez, Ricardo; Brismar, Hjalmar; Fu, Ying

2017-01-01

Colloidal semiconductor quantum dots (QDs) have been extensively researched and developed for biomedical applications, including drug delivery and biosensing assays. Hence, it is pivotal to understand their behavior in terms of intracellular transport and toxicological effects. In this study, we focused on 3-mercaptopropionic acid-coated CdSe-CdS/ZnS core-multishell quantum dots (3MPA-QDs) converted from the as-grown octadecylamine-coated quantum dots (ODA-QDs) and their direct and dynamic interactions with human umbilical vein endothelial cells (HUVECs). Live cell imaging using confocal fluorescence microscopy showed that 3MPA-QDs first attached to and subsequently aggregated on HUVEC plasma membrane ~25 min after QD deposition. The aggregated QDs started being internalized at ~2 h and reached their highest internalization degree at ~24 h. They were released from HUVECs after ~48 h. During the 48 h period, the HUVECs responded normally to external stimulations, grew, proliferated and wound healed without any perceptible apoptosis. Furthermore, 1) 3MPA-QDs were internalized in newly formed LysoTracker-stained early endosomes; 2) adenosine 5′-triphosphate-induced [Ca2+]i modulation caused a transient decrease in the fluorescence of 3MPA-QDs that were attached to the plasma membrane but a transient increase in the internalized 3MPA-QDs; and 3) fluorescence signal modulations of co-stained LysoTracker and QDs induced by the lysosomotropic agent Gly-Phe-β-naphthylamide were spatially co-localized and temporally synchronized. Our findings suggest that 3MPA-QDs converted from ODA-QDs are a potential nontoxic fluorescent probe for future use in clinical applications. Moreover, the photophysical strategy and techniques reported in this work are easily applicable to study of direct interactions between other nanoparticles and live cells; contributing to awareness and implementation of the safe applications of nanoparticles. PMID:29270011

Long-term stability of dentin matrix following treatment with various natural collagen cross-linkers

PubMed Central

Castellan, Carina Strano; Bedran-Russo, Ana Karina; Karol, Sachin; Rodrigues Pereira, Patrícia Nóbrega

2011-01-01

Objectives Collagen disorganization is one of the main degradation patterns found in unsuccessful adhesive restorations. The hypothesis of this study was that pretreatment using natural collagen cross-linking agents rich in proanthocyanidin (PA) would improve mechanical properties and stability over time of the dentin collagen and, thus, confer a more resistant and lasting substrate for adhesive restorations. Methods PA-based extracts, from grape seed (GSE), cocoa seed (CSE), cranberry (CRE), cinnamon (CNE) and açaí berry (ACE) were applied over the demineralized dentin. The apparent elastic modulus (E) of the treated dentin collagen was analyzed over a 12 months period. Specimens were immersed in the respective solution and E values were obtained by a micro-flexural test at baseline, 10, 30, 60, 120 and 240 min. Samples were stored in artificial saliva and re-tested after 3, 6 and 12 months. Data was analyzed using ANOVA and Tukey test. Results GSE and CSE extracts showed a time-dependant effect and were able to improve [240 min (MPa): GSE=108.96±56.08; CSE=59.21±24.87] and stabilize the E of the organic matrix [12 months (MPa): GSE=40.91±19.69; CSE= 42.11±13.46]. CRE and CNE extracts were able to maintain the E of collagen matrices constant over 12 months [CRE=11.17±7.22; CNE= 9,96±6.11; MPa]. ACE (2.64±1.22 MPa) and control groups immersed in neat distilled water (1.37±0.69 MPa) and ethanol water (0.95±0.33MPa) showed no effect over dentin organic matrix and enable their degradation and reduction of mechanical properties. Significance Some PA-based extracts were capable of improving and stabilizing collagen matrices through exogenous cross-links induction. PMID:21783144

Effects of High Hydrostatic Pressure on Bacterial Growth on Human Ossicles Explanted from Cholesteatoma Patients

PubMed Central

Ostwald, Jürgen; Lindner, Tobias; Zautner, Andreas Erich; Arndt, Kathleen; Pau, Hans Wilhelm; Podbielski, Andreas

2012-01-01

Background High hydrostatic pressure (HHP) treatment can eliminate cholesteatoma cells from explanted human ossicles prior to re-insertion. We analyzed the effects of HHP treatment on the microbial flora on ossicles and on the planktonic and biofilm states of selected isolates. Methodology Twenty-six ossicles were explanted from cholesteatoma patients. Five ossicles were directly analyzed for microbial growth without further treatment. Fifteen ossicles were cut into two pieces. One piece was exposed to HHP of 350 MPa for 10 minutes. Both the treated and untreated (control) pieces were then assessed semi-quantitatively. Three ossicles were cut into two pieces and exposed to identical pressure conditions with or without the addition of one of two different combinations of antibiotics to the medium. Differential effects of 10-minute in vitro exposure of planktonic and biofilm bacteria to pressures of 100 MPa, 250 MPa, 400 MPa and 540 MPa in isotonic and hypotonic media were analyzed using two patient isolates of Staphylococcus epidermidis and Neisseria subflava. Bacterial cell inactivation and biofilm destruction were assessed by colony counting and electron microscopy. Principal Findings A variety of microorganisms were isolated from the ossicles. Irrespective of the medium, HHP treatment at 350 MPa for 10 minutes led to satisfying but incomplete inactivation especially of Gram-negative bacteria. The addition of antibiotics increased the efficacy of elimination. A comparison of HHP treatment of planktonic and biofilm cells showed that the effects of HPP were reduced by about one decadic logarithmic unit when HPP was applied to biofilms. High hydrostatic pressure conditions that are suitable to inactivate cholesteatoma cells fail to completely sterilize ossicles even if antibiotics are added. As a result of the reduced microbial load and the viability loss of surviving bacteria, however, there is a lower risk of re-infection after re-insertion. PMID:22291908

Laboratory strength of glass ionomer and zinc phosphate cements.

PubMed

Piwowarczyk, A; Ottl, P; Lauer, H C

2001-09-01

The present in vitro study examined 3 mechanical properties, namely compressive, flexural, and diametral tensile strength, of various commercially available cements and core materials as a function of time after mixing. The examined materials were 2 cermet cements (Ketac Silver [ESPE, Seefeld, Germany] and Chelon Silver [ESPE]), 1 metal-reinforced glass ionomer cement (Miracle Mix [GC Dental Industrial Corp, Tokyo, Japan]), 2 conventional glass ionomer cements (Ketac Bond [ESPE] and Ketac Cem [ESPE]), 1 standard cure zinc phosphate cement (Harvard Cement [Richter and Hoffmann, Berlin, Germany]), and 1 zinc phosphate cement with the addition of 30% silver amalgam alloy powder (Harvard Cement 70% with Dispersalloy 30% [Richter and Hoffmann/Johnson and Johnson, East Windsor, NJ]). Properties were measured using a universal testing machine at 15 minutes, 1 hour, and 24 hours after first mixing. Compressive strengths varied widely between the 3 times of measurement from 5.8 +/- 6.6 MPa for Ketac Cem to 144.3 +/- 10.2 MPa for Ketac Silver. Twenty-four hours after mixing, the Bonferroni test showed significant (p

Evaluation of potential interactions between mycophenolic acid derivatives and proton pump inhibitors.

PubMed

Gabardi, Steven; Olyaei, Ali

2012-01-01

To evaluate the incidence of gastrointestinal (GI) complications in solid organ transplant (SOT) recipients, impact of the complications on transplant outcomes, and the potential interactions between mycophenolic acid (MPA) derivatives and proton pump inhibitors (PPIs). An unrestricted literature search (1980-January 2012) was performed with MEDLINE and EMBASE using the following key words: drug-drug interaction, enteric-coated mycophenolic acid, GI complications, mycophenolate mofetil, solid organ transplant, and proton pump inhibitor, including individual agents within the class. Abstracts from scientific meetings were also evaluated. Additionally, reference citations from identified publications were reviewed. Relevant English-language, original research articles and review articles were evaluated if they focused on any of the topics identified in the search or included substantial content addressing GI complications in SOT recipients or drug interactions. GI complications are frequent among SOT recipients, with some studies showing prevalence rates as high as 70%. Transplant outcomes among renal transplant recipients are significantly impacted by GI complications, especially in patients requiring immunosuppressant dosage reductions or premature discontinuation. To this end, PPI use among patients receiving transplants is common. Recent data demonstrate that PPIs significantly reduce the overall exposure to MPA after oral administration of mycophenolate mofetil. Similar studies show this interaction does not exist between PPIs and enteric-coated mycophenolic acid (EC-MPA). Unfortunately, most of the available data evaluating this interaction are pharmacokinetic analyses that do not investigate the clinical impact of this interaction. A significant interaction exists between PPIs and mycophenolate mofetil secondary to reduced dissolution of mycophenolate mofetil in higher pH environments. EC-MPA is not absorbed in the stomach; therefore, low intragastric acidity does not impact EC-MPA and bioavailability is maintained with this formulation during PPI coadministration. The clinical impact of this interaction is unknown, yet one can theorize that reduced exposure to MPA in SOT recipients can increase the risk of allograft rejection and/or failure.

Using neutron diffraction to examine the onset of mechanical twinning in calcite rocks

NASA Astrophysics Data System (ADS)

Covey-Crump, S. J.; Schofield, P. F.; Oliver, E. C.

2017-07-01

Experimental calibration of the calcite twin piezometer is complicated by the difficulty of establishing the stresses at which the twins observed in the final deformation microstructures actually formed. In principle, this difficulty may be circumvented if the deformation experiments are performed in a polychromatic neutron beam-line because this allows the elastic strain (and hence stress) in differently oriented grains to be simultaneously monitored from diffraction patterns collected as the experiment is proceeding. To test this idea small strain (<0.3%), uniaxial compression experiments have been performed on Carrara marble (grain size 150 μm) and Solnhofen limestone (5 μm) at temperatures of 20°-600 °C using the ENGIN-X instrument at the ISIS neutron facility, UK. At the lowest temperatures (25 °C Carrara; 200 °C Solnhofen) the deformation response was purely elastic up to the greatest stresses applied (60 MPa Carrara; 175 MPa Solnhofen). The sign of the calcite elastic stiffness component c14 is confirmed to be positive when the obverse setting of the calcite rhombohedral lattice in hexagonal axes is used. In the Carrara marble samples deformed at higher temperatures, elastic twinning was initiated at small stresses (<15 MPa) in grains oriented such that the Schmid factor for twinning was positive on more than one e-twin system. At greater stresses (65 MPa at 200 °C decreasing to 41 MPa at 500 °C) there was an abrupt onset of permanent twinning in grains with large Schmid factors for twinning on any one e-twin system. No twinning was observed in the Solnhofen limestone samples deformed at 200° or 400 °C at applied stresses of <180 MPa. These results highlight the potential of this approach for detecting the onset of twinning and provide, through experiments on samples with different microstructures, a strategy for systematically investigating the effects of microstructural variables on crystallographically-controlled inelastic processes.

An integrative modeling approach for the efficient estimation of cross sectional tibial stresses during locomotion.

PubMed

Derrick, Timothy R; Edwards, W Brent; Fellin, Rebecca E; Seay, Joseph F

2016-02-08

The purpose of this research was to utilize a series of models to estimate the stress in a cross section of the tibia, located 62% from the proximal end, during walking. Twenty-eight male, active duty soldiers walked on an instrumented treadmill while external force data and kinematics were recorded. A rigid body model was used to estimate joint moments and reaction forces. A musculoskeletal model was used to gather muscle length, muscle velocity, moment arm and orientation information. Optimization procedures were used to estimate muscle forces and finally internal bone forces and moments were applied to an inhomogeneous, subject specific bone model obtained from CT scans to estimate stress in the bone cross section. Validity was assessed by comparison to stresses calculated from strain gage data in the literature and sensitivity was investigated using two simplified versions of the bone model-a homogeneous model and an ellipse approximation. Peak compressive stress occurred on the posterior aspect of the cross section (-47.5 ± 14.9 MPa). Peak tensile stress occurred on the anterior aspect (27.0 ± 11.7 MPa) while the location of peak shear was variable between subjects (7.2 ± 2.4 MPa). Peak compressive, tensile and shear stresses were within 0.52 MPa, 0.36 MPa and 3.02 MPa respectively of those calculated from the converted strain gage data. Peak values from a inhomogeneous model of the bone correlated well with homogeneous model (normal: 0.99; shear: 0.94) as did the normal ellipse model (r=0.89-0.96). However, the relationship between shear stress in the inhomogeneous model and ellipse model was less accurate (r=0.64). The procedures detailed in this paper provide a non-invasive and relatively quick method of estimating cross sectional stress that holds promise for assessing injury and osteogenic stimulus in bone during normal physical activity. Copyright © 2016 Elsevier Ltd. All rights reserved.