Progression of soot cake layer properties during the systematic regeneration of diesel particulate filters measured with neutron tomography

DOE PAGES

Toops, Todd J.; Pihl, Josh A.; Finney, Charles E. A.; ...

2015-01-16

Although particulate filters (PFs) have been a key component of the emission control system for modern diesel engines, there remain significant questions about the basic regeneration behavior of the filters and how it changes with accumulation of increasing soot layers. This effort describes a systematic deposition and regeneration of particulate matter in 25-mm diameter × 76-mm long wall-flow PFs composed of silicon carbide (SiC) material. The initial soot distributions were analyzed for soot cake thickness using a nondestructive neutron imaging technique. With the PFs intact, it was then possible to sequentially regenerate the samples and reanalyze them, which was performedmore » after nominal 20, 50, and 70 % regenerations. The loaded samples show a relatively uniform distribution of particulate with an increasing soot cake thickness and nearly identical initial density of 70 mg/cm 3. Throughout regeneration, the soot cake thickness initially decreases significantly while the density increases to 80–90 mg/cm 3. After ~50 % regeneration, the soot cake thickness stays relatively constant, but instead, the density decreases as pores open up in the layer (~35 mg/cm 3 at 70 % regeneration). Here, complete regeneration initially occurs at the rear of the PF channels. With this information, a conceptual model of the regeneration is proposed.« less

Progression of soot cake layer properties during the systematic regeneration of diesel particulate filters measured with neutron tomography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Toops, Todd J.; Pihl, Josh A.; Finney, Charles E. A.

Although particulate filters (PFs) have been a key component of the emission control system for modern diesel engines, there remain significant questions about the basic regeneration behavior of the filters and how it changes with accumulation of increasing soot layers. This effort describes a systematic deposition and regeneration of particulate matter in 25-mm diameter × 76-mm long wall-flow PFs composed of silicon carbide (SiC) material. The initial soot distributions were analyzed for soot cake thickness using a nondestructive neutron imaging technique. With the PFs intact, it was then possible to sequentially regenerate the samples and reanalyze them, which was performedmore » after nominal 20, 50, and 70 % regenerations. The loaded samples show a relatively uniform distribution of particulate with an increasing soot cake thickness and nearly identical initial density of 70 mg/cm 3. Throughout regeneration, the soot cake thickness initially decreases significantly while the density increases to 80–90 mg/cm 3. After ~50 % regeneration, the soot cake thickness stays relatively constant, but instead, the density decreases as pores open up in the layer (~35 mg/cm 3 at 70 % regeneration). Here, complete regeneration initially occurs at the rear of the PF channels. With this information, a conceptual model of the regeneration is proposed.« less

Removal of residual particulate matter from filter media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Almlie, Jay C.; Miller, Stanley J.

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

Removal of residual particulate matter from filter media

DOEpatents

Almlie, Jay C; Miller, Stanley J

2014-11-11

A method for removing residual filter cakes that remain adhered to a filter after typical particulate removal methodologies have been employed, such as pulse-jet filter element cleaning, for all cleanable filters used for air pollution control, dust control, or powder control.

Use of sugarcane filter cake and nitrogen, phosphorus and potassium fertilization in the process of bioremediation of soil contaminated with diesel.

PubMed

Tellechea, Fernando Reynel Fundora; Martins, Marco Antônio; da Silva, Alexsandro Araujo; da Gama-Rodrigues, Emanuela Forestieri; Martins, Meire Lelis Leal

2016-09-01

This study evaluated the use of sugarcane filter cake and nitrogen, phosphorus and potassium (NPK) fertilization in the bioremediation of a soil contaminated with diesel fuel using a completely randomized design. Five treatments (uncontaminated soil, T1; soil contaminated with diesel, T2; soil contaminated with diesel and treated with 15 % (wt) filter cake, T3; soil contaminated with diesel and treated with NPK fertilizer, T4; and soil contaminated with diesel and treated with 15 % (wt) filter cake and NPK fertilizer, T5) and four evaluation periods (1, 60, 120, and 180 days after the beginning of the experiment) were used according to a 4 × 5 factorial design to analyze CO2 release. The variables total organic carbon (TOC) and total petroleum hydrocarbons (TPH) remaining in the soil were analyzed using a 5 × 2 factorial design, with the same treatments described above and two evaluation periods (1 and 180 days after the beginning of the experiment). In T3 and T5, CO2 release was significantly higher, compared with the other treatments. Significant TPH removal was observed on day 180, when percent removal values were 61.9, 70.1, 68.2, and 75.9 in treatments T2, T3, T4, and T5, respectively, compared with the initial value (T1).

49. EASTERN VIEW OF DORROLIVER VACUUM DRUM FILTER ASSEMBLY IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

49. EASTERN VIEW OF DORR-OLIVER VACUUM DRUM FILTER ASSEMBLY IN THE FILTER CAKE HOUSE. - U.S. Steel Duquesne Works, Basic Oxygen Steelmaking Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Microbial stability of worm castings and sugarcane filter mud compost blended with biochar

USDA-ARS?s Scientific Manuscript database

Organic amendments such as worm castings and filter mud compost can provide nutrient rich substrates for enhanced plant growth. Physico-chemical and microbial stability of these substrates might be enhanced with the addition of biochar. A series of experiments was carried out to determine the stab...

Visualization of flow during cleaning process on a liquid nanofibrous filter

NASA Astrophysics Data System (ADS)

Bílek, P.

2017-10-01

This paper deals with visualization of flow during cleaning process on a nanofibrous filter. Cleaning of a filter is very important part of the filtration process which extends lifetime of the filter and improve filtration properties. Cleaning is carried out on flat-sheet filters, where particles are deposited on the filter surface and form a filtration cake. The cleaning process dislodges the deposited filtration cake, which is loose from the membrane surface to the retentate flow. The blocked pores in the filter are opened again and hydrodynamic properties are restored. The presented optical method enables to see flow behaviour in a thin laser sheet on the inlet side of a tested filter during the cleaning process. The local concentration of solid particles is possible to estimate and achieve new information about the cleaning process. In the article is described the cleaning process on nanofibrous membranes for waste water treatment. The hydrodynamic data were compared to the images of the cleaning process.

Pozzolanic filtration/solidification of radionuclides in nuclear reactor cooling water

DOE Office of Scientific and Technical Information (OSTI.GOV)

Englehardt, J.D.; Peng, C.

1995-12-31

Laboratory studies to investigate the feasibility of one- and two-step processes for precipitation/coprecipitating radionuclides from nuclear reactor cooling water, filtering with pozzolanic filter aid, and solidifying, are reported in this paper. In the one-step process, ferrocyanide salt and excess lime are added ahead of the filter, and the resulting filter cake solidifies by a pozzolanic reaction. The two-step process involves addition of solidifying agents subsequent to filtration. It was found that high surface area diatomaceous synthetic calcium silicate powders, sold commercially as functional fillers and carriers, adsorb nickel isotopes from solution at neutral and slightly basic pH. Addition of themore » silicates to cooling water allowed removal of the tested metal isotopes (nickel, iron, manganese, cobalt, and cesium) simultaneously at neutral to slightly basic pH. Lime to diatomite ratio was the most influential characteristic of composition on final strength tested, with higher lime ratios giving higher strength. Diatomaceous earth filter aids manufactured without sodium fluxes exhibited higher pozzolanic activity. Pozzolanic filter cake solidified with sodium silicate and a ratio of 0.45 parts lime to 1 part diatomite had compressive strength ranging from 470 to 595 psi at a 90% confidence level. Leachability indices of all tested metals in the solidified waste were acceptable. In light of the typical requirement of removing iron and desirability of control over process pH, a two-step process involving addition of Portland cement to the filter cake may be most generally applicable.« less

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2012 CFR

2012-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2013 CFR

2013-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2014 CFR

2014-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2011 CFR

2011-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xi to Part 266 - Lead-Bearing Materials That May be Processed in Exempt Lead Smelters

Code of Federal Regulations, 2010 CFR

2010-07-01

... analyses Acid filters Baghouse bags Clothing (e.g., coveralls, aprons, shoes, hats, gloves) Sweepings Air filter bags and cartridges Respiratory cartridge filters Shop abrasives Stacking boards Waste shipping... pallets Water treatment sludges, filter cakes, residues, and solids Emission control dusts, sludges...

40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

Code of Federal Regulations, 2012 CFR

2012-07-01

... sweepings Air filters Electroplating bath filters Wastewater filter media Wood pallets Disposable clothing... cartridge filters Paper hand towels B. Exempt Nickel or Chromium-Bearing Materials when Generated by Any... Nickel, chromium, and iron catalysts Nickel-cadmium and nickel-iron batteries Filter cake from wet...

40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

Code of Federal Regulations, 2014 CFR

2014-07-01

... sweepings Air filters Electroplating bath filters Wastewater filter media Wood pallets Disposable clothing... cartridge filters Paper hand towels B. Exempt Nickel or Chromium-Bearing Materials when Generated by Any... Nickel, chromium, and iron catalysts Nickel-cadmium and nickel-iron batteries Filter cake from wet...

40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

Code of Federal Regulations, 2010 CFR

2010-07-01

... sweepings Air filters Electroplating bath filters Wastewater filter media Wood pallets Disposable clothing... cartridge filters Paper hand towels B. Exempt Nickel or Chromium-Bearing Materials when Generated by Any... Nickel, chromium, and iron catalysts Nickel-cadmium and nickel-iron batteries Filter cake from wet...

40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

Code of Federal Regulations, 2013 CFR

2013-07-01

... sweepings Air filters Electroplating bath filters Wastewater filter media Wood pallets Disposable clothing... cartridge filters Paper hand towels B. Exempt Nickel or Chromium-Bearing Materials when Generated by Any... Nickel, chromium, and iron catalysts Nickel-cadmium and nickel-iron batteries Filter cake from wet...

40 CFR Appendix Xii to Part 266 - Nickel or Chromium-Bearing Materials that may be Processed in Exempt Nickel-Chromium Recovery...

Code of Federal Regulations, 2011 CFR

2011-07-01

... sweepings Air filters Electroplating bath filters Wastewater filter media Wood pallets Disposable clothing... cartridge filters Paper hand towels B. Exempt Nickel or Chromium-Bearing Materials when Generated by Any... Nickel, chromium, and iron catalysts Nickel-cadmium and nickel-iron batteries Filter cake from wet...

Biogas production from Jatropha curcas press-cake.

PubMed

Staubmann, R; Foidl, G; Foidl, N; Gübitz, G M; Lafferty, R M; Arbizu, V M; Steiner, W

1997-01-01

Seeds of the tropical plant Jatropha curcas (purge nut, physic nut) are used for the production of oil. Several methods for oil extraction have been developed. In all processes, about 50% of the weight of the seeds remain as a press cake containing mainly protein and carbohydrates. Investigations have shown that this residue contains toxic compounds and cannot be used as animal feed without further processing. Preliminary experiments have shown that the residue is a good substrate for biogas production. Biogas formation was studied using a semicontinous upflow anaerobic sludge blanket (UASB) reactor; a contact-process and an anaerobic filter each reactor having a total volume of 110 L. A maximum production rate of 3.5 m3 m"3 d"1 was obtained in the anaerobic filter with a loading rate of 13 kg COD m~3 d"1. However, the UASB reactor and the contact-process were not suitable for using this substrate. When using an anaerobic filter with Jatropha curcas seed cake as a substrate, 76% of the COD was degraded and 1 kg degraded COD yielded 355 L of biogas containing 70% methane.

Recovering Bioactive Compounds from Olive Oil Filter Cake by Advanced Extraction Techniques

PubMed Central

Lozano-Sánchez, Jesús; Castro-Puyana, María; Mendiola, Jose A.; Segura-Carretero, Antonio; Cifuentes, Alejandro; Ibáñez, Elena

2014-01-01

The potential of by-products generated during extra-virgin olive oil (EVOO) filtration as a natural source of phenolic compounds (with demonstrated bioactivity) has been evaluated using pressurized liquid extraction (PLE) and considering mixtures of two GRAS (generally recognized as safe) solvents (ethanol and water) at temperatures ranging from 40 to 175 °C. The extracts were characterized by high-performance liquid chromatography (HPLC) coupled to diode array detection (DAD) and electrospray time-of-flight mass spectrometry (HPLC-DAD-ESI-TOF/MS) to determine the phenolic-composition of the filter cake. The best isolation procedure to extract the phenolic fraction from the filter cake was accomplished using ethanol and water (50:50, v/v) at 120 °C. The main phenolic compounds identified in the samples were characterized as phenolic alcohols or derivatives (hydroxytyrosol and its oxidation product), secoiridoids (decarboxymethylated and hydroxylated forms of oleuropein and ligstroside aglycones), flavones (luteolin and apigenin) and elenolic acid derivatives. The PLE extraction process can be applied to produce enriched extracts with applications as bioactive food ingredients, as well as nutraceuticals. PMID:25226536

Accelerated coffee pulp composting.

PubMed

Sánchez, G; Olguín, E J; Mercado, G

1999-02-01

The effect of two abundant, easily available and very low-cost agro-industrial organic residues, i.e., filter cake from the sugar industry and poultry litter, on the composting stabilization time of coffee pulp and on the quality of the produced compost, was evaluated. Piles of one cubic meter were built and monitored within the facilities of a coffee processing plant in the Coatepec region of the State of Veracruz, Mexico. Manual aeration was carried out once a week. A longer thermophilic period (28 days) and a much lower C/N ratio (in the range of 6.9-9.1) were observed in the piles containing the amendments, as compared to the control pile containing only coffee pulp (14 days and a C/N ratio of 14.4, respectively). The maximum assimilation rate of the reducing sugars was 1.6 g kg-1 d-1 (from 7.5 to 5.3%) during the first two weeks when accelerators were present in the proportion of 20% filter cake plus 20% poultry litter, while they accumulated at a rate of 1.2 g kg-1 d-1 (from 7.4 to 9.13%) during the same period in the control pile. The best combination of amendments was 30% filter cake with 20% poultry litter, resulting in a final nitrogen content as high as 4.81%. The second best combination was 20% filter cake with 10% poultry litter, resulting in a compost which also contained a high level of total nitrogen (4.54%). It was concluded that the use of these two residues enhanced the composting process of coffee pulp, promoting a shorter stabilization period and yielding a higher quality of compost.

Comparison of start-up strategies and process performance during semi-continuous anaerobic digestion of sugarcane filter cake co-digested with bagasse.

PubMed

Janke, Leandro; Leite, Athaydes F; Nikolausz, Marcell; Radetski, Claudemir M; Nelles, Michael; Stinner, Walter

2016-02-01

The anaerobic digestion of sugarcane filter cake and the option of co-digestion with bagasse were investigated in a semi-continuous feeding regime to assess the main parameters used for large-scale process designing. Moreover, fresh cattle manure was considered as alternative inoculum for the start-up of biogas reactors in cases where digestate from a biogas plant would not be available in remote rural areas. Experiments were carried out in 6 lab-scale semi-continuous stirred-tank reactors at mesophilic conditions (38±1°C) while the main anaerobic digestion process parameters monitored. Fresh cattle manure demonstrated to be appropriate for the start-up process. However, an acclimation period was required due to the high initial volatile fatty acids concentration (8.5gL(-1)). Regardless the mono-digestion of filter cake presented 50% higher biogas yield (480mLgVS(-1)) than co-digestion with bagasse (320mLgVS(-1)) during steady state conditions. A large-scale co-digestion system would produce 58% more biogas (1008m(3)h(-1)) than mono-digestion of filter cake (634m(3)h(-1)) due to its higher biomass availability for biogas conversion. Considering that the biogas production rate was the technical parameter that displayed the most relevant differences between the analyzed substrate options (0.99-1.45m(3)biogasm(3)d(-1)). The decision of which substrate option should be implemented in practice would be mainly driven by the available construction techniques, since economically efficient tanks could compensate the lower biogas production rate of co-digestion option. Copyright © 2015 Elsevier Ltd. All rights reserved.

Feasibility of utilization of horse dung spiked filter cake in vermicomposters using exotic earthworm Eisenia foetida.

PubMed

Sangwan, Pritam; Kaushik, C P; Garg, V K

2008-05-01

This contribution reports the potential of vermicomposting technology in the management of horse dung (HD) spiked sugar mill filter cake (SMFC) using an epigeic earthworm Eisenia foetida under laboratory conditions. A total of six vermicomposters filled with different ratios of HD and SMFC were maintained for this study. The growth and fecundity of E. foetida was monitored for 12 weeks. Maximum growth was recorded in 90% HD+10% SMFC feed mixture containing vermicomposter. Earthworms' biomass gain and reproduction was favorably up to 50% HD+50% SMFC feed composition. Maximum cocoons were also recorded in 90% HD+10% SMFC feed mixtures, however increasing proportions of SMFC in different vermicomposters affected the growth and fecundity of worms. A significant decrease in C:N ratio and increase in total kjeldahl nitrogen, total available phosphorus and calcium contents was recorded. The heavy metals content was higher in the vermicompost obtained in all the reactors than initial feed substrates. Based on investigations it is concluded that vermicomposting could be an alternative technology for the management of filter cake if it is mixed in 1:1 ratio with horse dung.

Biogas production from Jatropha curcas press-cake

DOE Office of Scientific and Technical Information (OSTI.GOV)

Staubmann, R.; Guebitz, G.M.; Lafferty, R.M.

Seeds of the tropical plant Jatropha curcas (purge nut, physic nut) are used for the production of oil. Several methods for oil extraction have been developed. In all processes, about 50% of the weight of the seeds remain as a press cake containing mainly protein and carbohydrates. Investigations have shown that this residue contains toxic compounds and cannot be used as animal feed without further processing. Preliminary experiments have shown that the residue is a good substrate for biogas production. Biogas formation was studied using a semicontinous upflow anaerobic sludge blanket (UASB) reactor; a contact-process and an anaerobic filter eachmore » reactor having a total volume of 110 L. A maximum production rate of 3.5 m{sup 3} m{sup -3} d{sup -1} was obtained in the anaerobic filter with a loading rate of 13 kg COD m{sup -3} d{sup -1}. However, the UAS reactor and the contact-process were not suitable for using this substrate. When using an anaerobic filter with Jatropha curcas seed cake as a substrate, 76% of the COD was degraded and 1 kg degraded COD yielded 355 L of biogas containing 70% methane. 28 refs., 3 figs., 4 tabs.« less

IMPACT OF PHYSICAL AND CHEMICAL MUD CONTAMINATION ON WELLBORE CEMENT- FORMATION SHEAR BOND STRENGTH Authors: Arome Oyibo1 and Mileva Radonjic1 * 1. Craft and Hawkins Department of Petroleum Engineering, 2131 Patrick F. Taylor Hall, Louisiana State University, Baton Rouge, LA 70803, aoyibo1@tigers.lsu.edu, mileva@lsu.edu

NASA Astrophysics Data System (ADS)

Oyibo, A. E.

2013-12-01

Wellbore cement has been used to provide well integrity through zonal isolation in oil & gas wells and geothermal wells. Cementing is also used to provide mechanical support for the casing and protect the casing from corrosive fluids. Failure of cement could be caused by several factors ranging from poor cementing, failure to completely displace the drilling fluids to failure on the path of the casing. A failed cement job could result in creation of cracks and micro annulus through which produced fluids could migrate to the surface which could lead to sustained casing pressure, contamination of fresh water aquifer and blow out in some cases. In addition, cement failures could risk the release of chemicals substances from hydraulic fracturing into fresh water aquifer during the injection process. To achieve proper cementing, the drilling fluid should be completely displaced by the cement slurry. However, this is hard to achieve in practice, some mud is usually left on the wellbore which ends up contaminating the cement afterwards. The purpose of this experimental study is to investigate the impact of both physical and chemical mud contaminations on cement-formation bond strength for different types of formations. Physical contamination occurs when drilling fluids (mud) dries on the surface of the formation forming a mud cake. Chemical contamination on the other hand occurs when the drilling fluids which is still in the liquid form interacts chemically with the cement during a cementing job. We investigated the impact of the contamination on the shear bond strength and the changes in the mineralogy of the cement at the cement-formation interface to ascertain the impact of the contamination on the cement-formation bond strength. Berea sandstone and clay rich shale cores were bonded with cement cores with the cement-formation contaminated either physically or chemically. For the physically contaminated composite cores, we have 3 different sample designs: clean/not contaminated, scrapped and washed composite cores. Similarly, for the chemically contaminated samples we had 3 different sample designs: 0%, 5% and 10% mud contaminated composite cores. Shear test were performed on the composite cores to determine the shear bond strength and the results suggested that the detrimental impact of the contamination is higher when the cores are physically contaminated i.e. when we have mud cake present at the surface of the wellbore before a cement job is performed. Also, the results showed that shear bond strength is higher for sandstone formations as compared to shale formations. Material characterization analysis was carried out to determine the micro structural changes at the cement-formation interface. The results obtained from the SEM and micro CT images taken at the bond interface confirmed that chemical contamination caused substantial changes in the spatial distribution of minerals that impacted bond strength. Keywords: Cement-Formation bond strength, mud contamination, shale, sandstone and material characterization *Corresponding author

Study of change of hydrophysical properties of bore mud in process of its utilization into man-induced soil

NASA Astrophysics Data System (ADS)

Gaevaya, E. V.; Bogaychuk, Y. E.; Tarasova, S. S.; Skipin, L. N.; Zaharova, E. V.

2017-10-01

The article considers the results of studies of the chemical and granulometric content and the factor of bore mud filtration in the process of its utilization. When the phosphogypsum is added, hydrophysical properties of the bore mud improve. At the same time, gradation of soil from the water-proof to weakly permeable takes place. This phenomenon is connected with recovery of filterability at the expense of ion-exchange reaction and a decrease of the silt fraction content in the bore mud. During the adding of phosphogypsum in the bore mud, pH decreased and made up 7.6-7.8 U. The decrease of the concentration of chloride-ions and sulphate-ions took place at the expense of replacement of Na+ by cations of Ca2+ that contributed to the formation of the water-stable structure with good filterability. The content of total forms of heavy metals in man-induced soil was lower than MAC (APC) for the loams. Man-induced soil has a V class of danger for the surrounding environment.

Specific Resistance. Operational Control Tests for Wastewater Facilities. Instructor's Manual [and] Student Workbook.

ERIC Educational Resources Information Center

Wooley, John F.

A commonly used test for determining filterability of conditioned sludge is the specific resistance (Buchner funnel) test. The sludge is filtered through filter paper using a Buchner funnel, and the time needed to obtain a given volume of filtrate (or for cake residue to begin to crack) is measured. The shorter the time, the better the…

Proposal for a better integration of bacterial lysis into the production of plasmid DNA at large scale.

PubMed

O'Mahony, Kevin; Freitag, Ruth; Hilbrig, Frank; Müller, Patrick; Schumacher, Ivo

2005-09-23

The paper addresses the question of how to achieve bacterial lysis in large-scale plasmid DNA production processes, where conventional alkaline lysis may become awkward to handle. Bacteria were grown in shaker flasks and a bioreactor. Suboptimal growth conditions were found advantageous for stable plasmid production at high copy numbers (up to 25mg/L could be achieved). Cells were harvested by filtration in the presence of a filter aid. A linear relationship between the biomass and the optimal filter aid concentration in terms of back pressure could be established. Bacteria-containing filter cakes were washed with isotonic buffer and lysis was achieved in situ by a two-step protocol calling for fragilisation of the cells followed by heat lysis in a suitable buffer. RNA and other soluble cell components where washed out of the cake during this step, while the plasmid DNA was retained. Afterwards a clear lysate containing relatively pure plasmid DNA could be eluted from the cake mostly as the desired supercoiled topoisomer, while cell debris and genomic DNA were retained. Lysis is, thus, integrated not only with cell capture but also with a significant degree of isolation/purification, as most impurities were considerably reduced during the procedure.

E.I. DuPont De Nemours & Company/Oberlin Filter Company Microfiltration Technology. Applications Analysis Report

EPA Science Inventory

This report evaluates the DuPont/Oberlin microfiltration technology’s ability to remove metals (present in soluble or insoluble form) and particulates from liquid wastes while producing a dry filter cake and a filtrate that meet applicable disposal requirements. This report also ...

Design parameters for rotating cylindrical filtration

NASA Technical Reports Server (NTRS)

Schwille, John A.; Mitra, Deepanjan; Lueptow, Richard M.

2002-01-01

Rotating cylindrical filtration displays significantly reduced plugging of filter pores and build-up of a cake layer, but the number and range of parameters that can be adjusted complicates the design of these devices. Twelve individual parameters were investigated experimentally by measuring the build-up of particles on the rotating cylindrical filter after a fixed time of operation. The build-up of particles on the filter depends on the rotational speed, the radial filtrate flow, the particle size and the gap width. Other parameters, such as suspension concentration and total flow rate are less important. Of the four mechanisms present in rotating filters to reduce pore plugging and cake build-up, axial shear, rotational shear, centrifugal sedimentation and vortical motion, the evidence suggests rotational shear is the dominant mechanism, although the other mechanisms still play minor roles. The ratio of the shear force acting parallel to the filter surface on a particle to the Stokes drag acting normal to the filter surface on the particle due to the difference between particle motion and filtrate flow can be used as a non-dimensional parameter that predicts the degree of particle build-up on the filter surface for a wide variety of filtration conditions. c2002 Elsevier Science B.V. All rights reserved.

Pressurised electro-osmotic dewatering of activated and anaerobically digested sludges: electrical variables analysis.

PubMed

Citeau, M; Olivier, J; Mahmoud, A; Vaxelaire, J; Larue, O; Vorobiev, E

2012-09-15

Pressurised electro-osmotic dewatering (PEOD) of two sewage sludges (activated and anaerobically digested) was studied under constant electric current (C.C.) and constant voltage (C.V.) with a laboratory chamber simulating closely an industrial filter. The influence of sludge characteristics, process parameters, and electrode/filter cloth position was investigated. The next parameters were tested: 40 and 80 A/m², 20, 30, and 50 V-for digested sludge dewatering; and 20, 40 and 80 A/m², 20, 30, and 50 V-for activated sludge dewatering. Effects of filter cloth electric resistance and initial cake thickness were also investigated. The application of PEOD provides a gain of 12 points of dry solids content for the digested sludge (47.0% w/w) and for the activated sludge (31.7% w/w). In PEOD processed at C.C. or at C.V., the dewatering flow rate was similar for the same electric field intensity. In C.C. mode, both the electric resistance of cake and voltage increase, causing a temperature rise by ohmic effect. In C.V. mode, a current intensity peak was observed in the earlier dewatering period. Applying at first a constant current and later on a constant voltage, permitted to have better control of ohmic heating effect. The dewatering rate was not significantly affected by the presence of filter cloth on electrodes, but the use of a thin filter cloth reduced remarkably the energy consumption compared to a thicker one: 69% of reduction energy input at 45% w/w of dry solids content. The reduction of the initial cake thickness is advantageous to increase the final dry solids content. Copyright © 2012 Elsevier Ltd. All rights reserved.

Investigating Created Properties of Nanoparticles Based Drilling Mud

NASA Astrophysics Data System (ADS)

Ghasemi, Nahid; Mirzaee, Mojtaba; Aghayari, Reza; Maddah, Heydar

2018-05-01

The success of drilling operations is heavily dependent on the drilling fluid. Drilling fluids cool down and lubricate the drill bit, remove cuttings, prevent formation damage, suspend cuttings and also cake off the permeable formation, thus retarding the passage of fluid into the formation. Typical micro or macro sized loss circulation materials (LCM) show limited success, especially in formations dominated by micropores, due to their relatively large sizes. Due to unique characteristics of nanoparticles such as their size and high surface area to volume ratio, they play an effective role in solving problems associated with the drilling fluid. In this study, we investigate the effect of adding Al2O3 and TiO2 nanoparticles into the drilling mud. Al2O3 and TiO2 nanoparticles were used in 20 and 60 nm of size and 0.05 wt% in concentration. Investigating the effects of temperature and pressure has shown that an increase in temperature can reduce the drilling mud rheological properties such as plastic viscosity, while an increase in pressure can enhance these properties. Also, the effects of pressure in high temperatures were less than those in low temperatures. Studying the effects of adding nanoparticles has shown that they can reduce the drilling mud rheological properties. Moreover, they can increase gel strength, reduce capillary suction time and decrease formation damage.

Personal equipment for low seam coal miners. 8. Improved traction rubber boot soles. Report for 1978-82

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanders, M.S.; Downing, J.V.

1982-10-01

Based on laboratory and preliminary field tests of off-the-shelf steel-toed rubber boots, a molded sole design was developed to provide increased traction over conventional calendared sole miners boots. The pattern provided sharp edges perpendicular to both lateral and fore-aft slip vectors. The sole was designed to reduce mud caking. An instep lace-up capability was added to better secure the foot inside the boot. A 5-month field evaluation compared the prototype boots to the boots the participants usually wear.

Mechanisms of action of particles used for fouling mitigation in membrane bioreactors.

PubMed

Loulergue, P; Weckert, M; Reboul, B; Cabassud, C; Uhl, W; Guigui, C

2014-12-01

Adding chemicals to the biofluid is an option to mitigate membrane fouling in membrane bioreactors. In particular, previous studies have shown that the addition of particles could enhance activated sludge filterability. Nevertheless, the mechanisms responsible for the improved filtration performance when particles are added are still unclear. Two main mechanisms might occur: soluble organic matter adsorption onto the particles and/or cake structure modification. To date, no studies have clearly dissociated the impact of these two phenomena as a method was needed for the in-line characterization of the cake structure during filtration. The objective of this study was thus to apply, for the first time, an optical method for in-situ, non-invasive, characterization of cake structure during filtration of a real biofluid in presence of particles. This method was firstly used to study local cake compressibility during the biofluid filtration. It was found that the first layers of the cake were incompressible whereas the cake appeared to be compressible at global scale. This questions the global scale analysis generally used to study cake compressibility and highlights the interest of coupling local characterization with overall process performance analysis. Secondly, the impact of adding submicronic melamine particles into the biofluid was studied. It appears that particles added into the biofluid strongly influence the cake properties, making it thicker and more permeable. Furthermore, by using liquid chromatography with an organic carbon detector to determine the detailed characteristics of the feed and permeate, it was shown that the modification of cake structure also affected the retention of soluble organic compounds by the membrane and thus the cake composition. Simultaneous use of a method for in-situ characterization of the cake structure with a detailed analysis of the fluid composition and monitoring of the global performance is thus a powerful method for evaluating cake structure and composition and their impact on global process performance. The use of this methodology should allow "cake engineering" to be developed so that cake properties (structure, composition) can be controlled and process performance optimized. Copyright © 2014 Elsevier Ltd. All rights reserved.

Acute and physical effects of water-based drilling mud in the marine copepod Calanus finmarchicus.

PubMed

Farkas, Julia; Yvonne Bådsvik, Camilla; Altin, Dag; Nordtug, Trond; Olsen, Anders Johny; Hansen, Bjørn Henrik

2017-01-01

The aim of this study was to investigate impacts of fine particulate fraction of a commonly used barite-containing drilling mud on the pelagic filter feeding copepod Calanus finmarchicus. The results show that the tested drilling mud had a low acute toxicity on C. finmarchicus (LC50 > 320 mg/L) and that the observed toxicity was likely caused by dissolved constituents in the mud and not the particle phase containing the weighting agent barite. Further, animals were exposed to drilling mud at a concentration of 10 mg/L for 168 hr followed by a 100 hr recovery phase. A rapid uptake of drilling mud particles was observed, while the excretion was slow and incomplete even after 100 hr recovery in clean seawater. The uptake of drilling mud particles caused a significant increase in sinking velocity of copepods, indicating that uptake of drilling mud particles affected their buoyancy. Long-term exposure to low concentrations of drilling mud could therefore cause physical effects such as impacts on the animal's buoyancy which may affect the energy budget of the copepods.

Enhanced sludge dewatering by electrofiltration. A feasibility study.

PubMed

Saveyn, H; Huybregts, L; Van der Meeren, P

2001-01-01

Sludge treatment is a major issue in today's waste water treatment. One of the problems encountered is the limiting dewaterability of mainly biological sludges, causing high final treatment costs for incineration or landfill. Although during recent years, improvements are realised in the field of dewatering, the actual dry solids content after dewatering remains at a maximum value of about 35%. In order to increase the dry solids content, the technique of electrofiltration was investigated. Electrofiltration is the combination of two known techniques, traditional pressure filtration and electroosmotic/electrophoretic dewatering. Pressure filtration is based on pressure as the driving force for dewatering a sludge. Limitations hereby lie in the clogging of the filter cloth due to the build-up of the filtercake. Electroosmotic/electrophoretic dewatering is based on an electric field to separate sludge colloid particles from the surrounding liquid by placing the sludge liquor between two oppositely charged electrodes. In this case, mobile sludge particles will move to one electrode due to their natural surface charge, and the liquid phase will be collected at the oppositely charged electrode. Combination of both techniques makes it possible to create a more homogeneous filter cake and prevent the filter from clogging, resulting in higher cake dry solids contents and shorter filtration cycles. To investigate the feasibility of this technique for the dewatering of activated sludge, a filter unit was developed for investigations on lab scale. Multiple dewatering tests were performed in which the electric parameters for electrofiltration were varied. It was derived from these experiments that very high filter cake dry solids contents (to more than 60%), and short filtration cycles were attainable by using a relatively small electric DC field. The power consumption was very low compared to the power needed to dewater sludge by thermal drying techniques. For this reason, this technique seems very promising for the dewatering of biological sludges.

77 FR 4835 - Petitions for Modification of Application of Existing Mandatory Safety Standards

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-31

... ingredients, thereby creating a ``filter-cake.'' At the end of the brewing process, following fermentation... process, following fermentation that results in the creation of the alcohol-containing liquid that is...

Utilization of drilling cuttings with extraction of ground for recultivation of disturbed soils

NASA Astrophysics Data System (ADS)

Gaevaya, E. V.; Bogaychuk, Y. E.; Tarasova, S. S.; Skipin, L. N.; Zakharova, E. V.

2017-10-01

Drilling of wells is connected with formation of the bore mud represented by the drill cutting with waste drilling mud. Bore mud has negative physical-chemical, physical and chemical properties: high content of salts, increased alkalinity, ash structure, soil overcrust, low airing, weak filterability and so on. In case of phosphogypsum adding to the bore mud, pH level decreases from the alkaline (10.5 U) to weakly alkaline 7.6 U, decrease of pH is connected with the influence of phosphogypsum acidity and neutralization of the more mud. Concentration of chloride ions and sulphate ions in reclaimed bore mud was 70±7 and 456±46 correspondingly. Presence of oil products in received soil was 198.0-219.0 mg/kg. When adding phosphogypsum, sand, sorbent and humic formulation «Rostok» to the bore mud, it has shown good germinating ability of cultures- phytomeliorants (93,3%). 100% germinating ability was observed in meadow grass with a height of overground sprouts 10.7 cm, germinating ability of red fescue was 80% with height of overground sprouts 9.6 cm.

Apparatus and method for removing particulate deposits from high temperature filters

DOEpatents

Nakaishi, Curtis V.; Holcombe, Norman T.; Micheli, Paul L.

1992-01-01

A combustion of a fuel-air mixture is used to provide a high-temperature and high-pressure pulse of gaseous combustion products for the back-flush cleaning of ceramic filter elements contained in a barrier filter system and utilized to separate particulates from particulate-laden process gases at high temperature and high pressure. The volume of gaseous combustion products provided by the combustion of the fuel-air mixture is preferably divided into a plurality of streams each passing through a sonic orifice and conveyed to the open end of each filter element as a high pressure pulse which passes through the filter elements and dislodges dust cake supported on a surface of the filter element.

PERFORMANCE IMPROVEMENT OF CROSS-FLOW FILTRATION FOR HIGH LEVEL WASTE TREATMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duignan, M.; Nash, C.; Poirier, M.

2011-01-12

In the interest of accelerating waste treatment processing, the DOE has funded studies to better understand filtration with the goal of improving filter fluxes in existing cross-flow equipment. The Savannah River National Laboratory (SRNL) was included in those studies, with a focus on start-up techniques, filter cake development, the application of filter aids (cake forming solid precoats), and body feeds (flux enhancing polymers). This paper discusses the progress of those filter studies. Cross-flow filtration is a key process step in many operating and planned waste treatment facilities to separate undissolved solids from supernate slurries. This separation technology generally has themore » advantage of self-cleaning through the action of wall shear stress created by the flow of waste slurry through the filter tubes. However, the ability of filter wall self-cleaning depends on the slurry being filtered. Many of the alkaline radioactive wastes are extremely challenging to filtration, e.g., those containing compounds of aluminum and iron, which have particles whose size and morphology reduce permeability. Unfortunately, low filter flux can be a bottleneck in waste processing facilities such as the Savannah River Modular Caustic Side Solvent Extraction Unit and the Hanford Waste Treatment Plant. Any improvement to the filtration rate would lead directly to increased throughput of the entire process. To date increased rates are generally realized by either increasing the cross-flow filter axial flowrate, limited by pump capacity, or by increasing filter surface area, limited by space and increasing the required pump load. SRNL set up both dead-end and cross-flow filter tests to better understand filter performance based on filter media structure, flow conditions, filter cleaning, and several different types of filter aids and body feeds. Using non-radioactive simulated wastes, both chemically and physically similar to the actual radioactive wastes, the authors performed several tests to demonstrate increases in filter performance. With the proper use of filter flow conditions and filter enhancers, filter flow rates can be increased over rates currently realized today.« less

49. LOOKING NORTH AT EVAPORATIVE WASTE WATER TREATMENT COOLING TOWERS, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

49. LOOKING NORTH AT EVAPORATIVE WASTE WATER TREATMENT COOLING TOWERS, WITH BLOW ENGINE HOUSE No. 3 ON RIGHT, AND FILTER CAKE HOUSE IN FOREGROUND. (Jet Lowe) - U.S. Steel Duquesne Works, Blast Furnace Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Experimental evaluation of main emissions during coal processing waste combustion.

PubMed

Dmitrienko, Margarita A; Legros, Jean C; Strizhak, Pavel A

2018-02-01

The total volume of the coal processing wastes (filter cakes) produced by Russia, China, and India is as high as dozens of millions of tons per year. The concentrations of CO and CO 2 in the emissions from the combustion of filter cakes have been measured directly for the first time. They are the biggest volume of coal processing wastes. There have been many discussions about using these wastes as primary or secondary components of coal-water slurries (CWS) and coal-water slurries containing petrochemicals (CWSP). Boilers have already been operationally tested in Russia for the combustion of CWSP based on filter cakes. In this work, the concentrations of hazardous emissions have been measured at temperatures ranging from 500 to 1000°С. The produced CO and CO 2 concentrations are shown to be practically constant at high temperatures (over 900°С) for all the coal processing wastes under study. Experiments have shown the feasibility to lowering the combustion temperatures of coal processing wastes down to 750-850°С. This provides sustainable combustion and reduces the CO and CO 2 emissions 1.2-1.7 times. These relatively low temperatures ensure satisfactory environmental and energy performance of combustion. Using CWS and CWSP instead of conventional solid fuels significantly reduces NO x and SO x emissions but leaves CO and CO 2 emissions practically at the same level as coal powder combustion. Therefore, the environmentally friendly future (in terms of all the main atmospheric emissions: CO, CO 2 , NO x , and SO x ) of both CWS and CWSP technologies relies on low-temperature combustion. Copyright © 2017 Elsevier Ltd. All rights reserved.

42. NORTHEAST VIEW OF BLOW ENGINE HOUSE No. 3, WITH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

42. NORTHEAST VIEW OF BLOW ENGINE HOUSE No. 3, WITH FILTER CAKE HOSUE IN CENTER FOREGROUND, AND EVAPORATIVE WASTE WATER TREATMENT COOLING TOWER TO THE LEFT. (Jet Lowe) - U.S. Steel Duquesne Works, Blast Furnace Plant, Along Monongahela River, Duquesne, Allegheny County, PA

Improved methane production from sugarcane vinasse with filter cake in thermophilic UASB reactors, with predominance of Methanothermobacter and Methanosarcina archaea and Thermotogae bacteria.

PubMed

Barros, Valciney Gomes de; Duda, Rose Maria; Vantini, Juliana da Silva; Omori, Wellington Pine; Ferro, Maria Inês Tiraboschi; Oliveira, Roberto Alves de

2017-11-01

Biogas production from sugarcane vinasse has enormous economic, energy, and environmental management potential. However, methane production stability and biodigested vinasse quality remain key issues, requiring better nutrient and alkalinity availability, operational strategies, and knowledge of reactor microbiota. This study demonstrates increased methane production from vinasse through the use of sugarcane filter cake and improved effluent recirculation, with elevated organic loading rates (OLR) and good reactor stability. We used UASB reactors in a two-stage configuration, with OLRs up to 45gCODL -1 d -1 , and obtained methane production as high as 3LL -1 d -1 . Quantitative PCR indicated balanced amounts of bacteria and archaea in the sludge (10 9 -10 10 copiesg -1 VS), and of the predominant archaea orders, Methanobacteriales and Methanosarcinales (10 6 -10 8 copiesg -1 VS). 16S rDNA sequencing also indicated the thermophilic Thermotogae as the most abundant class of bacteria in the sludge. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optimization of semi-continuous anaerobic digestion of sugarcane straw co-digested with filter cake: Effects of macronutrients supplementation on conversion kinetics.

PubMed

Janke, Leandro; Weinrich, Sören; Leite, Athaydes F; Schüch, Andrea; Nikolausz, Marcell; Nelles, Michael; Stinner, Walter

2017-12-01

Anaerobic digestion of sugarcane straw co-digested with sugarcane filter cake was investigated with a special focus on macronutrients supplementation for an optimized conversion process. Experimental data from batch tests and a semi-continuous experiment operated in different supplementation phases were used for modeling the conversion kinetics based on continuous stirred-tank reactors. The semi-continuous experiment showed an overall decrease in the performance along the inoculum washout from the reactors. By supplementing nitrogen alone or in combination to phosphorus and sulfur the specific methane production significantly increased (P<0.05) by 17% and 44%, respectively. Although the two-pool one-step model has fitted well to the batch experimental data (R 2 >0.99), the use of the depicted kinetics did not provide a good estimation for process simulation of the semi-continuous process (in any supplementation phase), possibly due to the different feeding modes and inoculum source, activity and adaptation. Copyright © 2017 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Y.V.; Baghy, M.O.

Sweet potato can yield 1000 gallons of ethanol/acre compared with 250-300 gal/acre for corn. Sweet potatoes of normal, relatively high, and very high dry-matter contents were fermented to ethanol. Pectinase was necessary to decrease viscosity before fermentation for economic processing, especially for varieties of normal and relatively high dry-matter contents. Attained yield of ethanol was 90% of theoretical value. After ethanol was distilled, residual stillage was separated by screening and centrifugation into filter cake, centrifuged solids, and stillage solubles. Filter cake and centrifuged solids had crude protein contents (nitrogen x 6.25, dry basis) of 22-32% and 42-57%, respectively, and accountedmore » for 44-85% and 0-17% of total sweet potato nitrogen. Sweet potatoes and their fermented products had 4.3-7.6 g of lysine/16 g of N and are expected to have good nutritional value. This practical method to ferment sweet potato for ethanol and to recover valuable protein-rich byproducts may have commercial potential. (Refs. 19).« less

Crossflow microfiltration of yeast suspensions in tubular filters.

PubMed

Redkar, S G; Davis, R H

1993-01-01

Crossflow microfiltration experiments were performed on yeast suspensions through 0.2-microns pore size ceramic and polypropylene tubes at various operating conditions. The initial transient flux decline follows dead-end filtration theory, with the membrane resistance determined from the initial flux and the specific cake resistance determined from the rate of flux decline due to cake buildup. For long times, the observed fluxes reach steady or nearly steady values, presumably as a result of the cake growth being arrested by the shear exerted at its surface. The steady-state fluxes increase with increasing shear rate and decreasing feed concentration, and they are nearly independent of transmembrane pressure. The steady-state fluxes for unwashed yeast in deionized water or fermentation media are typically 2-4 times lower than those predicted by a model based on the properties of nonadhesive, rigid spheres undergoing shear-induced back-diffusion. In contrast, the steady-state fluxes observed for washed yeast cells in deionized water are only 10-30% below the predicted values. The washed yeast cells also exhibited specific cake resistances that are an order of magnitude lower than those for the unwashed yeast. The differences are due to the presence of extracellular proteins and other macromolecules in the unwashed yeast suspensions. These biopolymers cause higher cell adhesion and resistance in the cake layer, so that the cells at the top edge are not free to diffuse away. This is manifested as a concentration jump from the edge of the cake layer to the sheared suspension adjacent to it.(ABSTRACT TRUNCATED AT 250 WORDS)

Novel microbial communities of the Haakon Mosby mud volcano and their role as a methane sink.

PubMed

Niemann, Helge; Lösekann, Tina; de Beer, Dirk; Elvert, Marcus; Nadalig, Thierry; Knittel, Katrin; Amann, Rudolf; Sauter, Eberhard J; Schlüter, Michael; Klages, Michael; Foucher, Jean Paul; Boetius, Antje

2006-10-19

Mud volcanism is an important natural source of the greenhouse gas methane to the hydrosphere and atmosphere. Recent investigations show that the number of active submarine mud volcanoes might be much higher than anticipated (for example, see refs 3-5), and that gas emitted from deep-sea seeps might reach the upper mixed ocean. Unfortunately, global methane emission from active submarine mud volcanoes cannot be quantified because their number and gas release are unknown. It is also unclear how efficiently methane-oxidizing microorganisms remove methane. Here we investigate the methane-emitting Haakon Mosby Mud Volcano (HMMV, Barents Sea, 72 degrees N, 14 degrees 44' E; 1,250 m water depth) to provide quantitative estimates of the in situ composition, distribution and activity of methanotrophs in relation to gas emission. The HMMV hosts three key communities: aerobic methanotrophic bacteria (Methylococcales), anaerobic methanotrophic archaea (ANME-2) thriving below siboglinid tubeworms, and a previously undescribed clade of archaea (ANME-3) associated with bacterial mats. We found that the upward flow of sulphate- and oxygen-free mud volcano fluids restricts the availability of these electron acceptors for methane oxidation, and hence the habitat range of methanotrophs. This mechanism limits the capacity of the microbial methane filter at active marine mud volcanoes to <40% of the total flux.

Fracturing fluid cleanup by controlled release of enzymes from polyelectrolyte complex nanoparticles

NASA Astrophysics Data System (ADS)

Barati Ghahfarokhi, Reza

Guar-based polymer gels are used in the oil and gas industry to viscosify fluids used in hydraulic fracturing of production wells, in order to reduce leak-off of fluids and pressure, and improve the transport of proppants. After fracturing, the gel and associated filter cake must be degraded to very low viscosities using breakers to recover the hydraulic conductivity of the well. Enzymes are widely used to achieve this but injecting high concentrations of enzyme may result in premature degradation, or failure to gel; denaturation of enzymes at alkaline pH and high temperature conditions can also limit their applicability. In this study, application of polyelectrolyte nanoparticles for entrapping, carrying, releasing and protecting enzymes for fracturing fluids was examined. The objective of this research is to develop nano-sized carriers capable of carrying the enzymes to the filter cake, delaying the release of enzyme and protecting the enzyme against pH and temperature conditions inhospitable to native enzyme. Polyethylenimine-dextran sulfate (PEI-DS) polyelectrolyte complexes (PECs) were used to entrap two enzymes commonly used in the oil industry in order to obtain delayed release and to protect the enzyme from conditions inhospitable to native enzyme. Stability and reproducibility of PEC nanoparticles was assured over time. An activity measurement method was used to measure the entrapment efficiency of enzyme using PEC nanoparticles. This method was confirmed using a concentration measurement method (SDS-PAGE). Entrapment efficiencies of pectinase and a commercial high-temperature enzyme mixture in polyelectrolyte complex nanoparticles were maximized. Degradation, as revealed by reduction in viscoelastic moduli of borate-crosslinked hydroxypropyl guar (HPG) gel by commercial enzyme loaded in polyelectrolyte nanoparticles, was delayed, compared to equivalent systems where the enzyme mixture was not entrapped. This indicates that PEC nanoparticles delay the activity of enzymes by entrapping them. It was also observed that control PEC nanoparticles decreased both viscoelastic moduli, but with a slower rate compared to the PEC nanoparticles loaded with enzyme. Preparation shear and applied shear showed no significant effect on activity of enzyme-loaded PEC nanoparticles mixed with HPG solutions. However, fast addition of chemicals during the preparations showed smaller particle size compared to the drop-wise method. PEC nanoparticles (PECNPs) also protected both enzymes from denaturation at elevated temperature and pH. Following preparation, enzyme-loaded PEC nanoparticles were mixed with borate crosslinked HPG and the mixture was injected through a shear loop. Pectinase-loaded nanoparticles mixed with gelled HPG showed no sensitivity to shear applied along the shear loop at 25 °C. However, EL2X-loaded PEC nanoparticles showed sensitivity to shear applied along the shear loop at 40 °C. Filter cake was formed and degraded in a fluid loss cell for borate crosslinked HPG solutions mixed with either enzymes or enzyme-loaded PEC nanoparticles. Cleanup slopes of filter cake degraded using enzyme-loaded PEC nanoparticles and systems with enzymes mixed with HPG gel were significantly higher than for the filter cake formed with HPG gel mixed with no enzyme. In a different application, enzyme-loaded PEC nanoparticles showed significantly slower reduction in viscosity of HPG solution over time compared to the HPG systems mixed with enzyme. Increasing the viscosity of low concentration HPG, used as slick-water, decreases the proppant settling velocity. This is of specific interest in fracturing fluids used for unconventional reservoirs.

Organic colloids and their influence on low-pressure membrane filtration.

PubMed

Laabs, C; Amy, G; Jekel, M

2004-01-01

Wastewater treatment by low-pressure membrane filtration (MF and UF) is affected to a large extent by macromolecules and colloids. In order to investigate the influence of organic colloids on the membrane filtration process, colloids were isolated from a wastewater treatment plant effluent using a rotary-evaporation pre-concentration step followed by dialysis. Stirred cell tests were carried out using redissolved colloids, with and without additional glass fiber filtration. After constant pressure membrane filtration of 190 L/m2, the initial flux had declined by 50% for colloids > 6-8 kD (glass fiber filtered) with a hydrophilic MF membrane and for colloids > 12-14 kD (glass fiber filtered) with a hydrophobic MF membrane. For the non-filtered colloidal solutions, the flux decline was even steeper with the flux being below 10% of the initial flux after 190 L/m2 were passed through the membranes. As with larger particles, colloids form a filtration cake layer on top of the membrane surface when used as isolates without prior filtration. This filtration cake is easily removed during backwashing. However, polysaccharides as a macromolecular component of the colloid isolate cause severe fouling by the formation of a gel layer on the membrane surface that is difficult to remove completely.

Use of a soft sensor for the fast estimation of dried cake resistance during a freeze-drying cycle.

PubMed

Bosca, Serena; Barresi, Antonello A; Fissore, Davide

2013-07-15

This paper deals with the determination of dried cake resistance in a freeze-drying process using the Smart Soft Sensor, a process analytical technology recently proposed by the authors to monitor the primary drying stage of a freeze-drying process. This sensor uses the measurement of product temperature, a mathematical model of the process, and the Kalman filter algorithm to estimate the residual amount of ice in the vial as a function of time, as well as the coefficient of heat transfer between the shelf and the product and the resistance of the dried cake to vapor flow. It does not require expensive (additional) hardware in a freeze-dryer, provided that thermocouples are available. At first, the effect of the insertion of the thermocouple in a vial on the structure of the product is investigated by means of experimental tests, comparing both sublimation rate and cake structure in vials with and without thermocouple. This is required to assess that the temperature measured by the thermocouple is the same of the product in the non-monitored vials, at least in a non-GMP environment, or when controlled nucleation methods are used. Then, results about cake resistance obtained in an extended experimental campaign with aqueous solutions containing different excipients (sucrose, mannitol and polyvinylpyrrolidone), processed in various operating conditions, are presented, with the goal to point out the accuracy of the proposed methodology. Copyright © 2013 Elsevier B.V. All rights reserved.

Development of an advanced, continuous mild gasification process for the production of co-products. Quarterly report, October 30, 1991--January 2, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

O`Neal, G.W.

1991-12-31

During this quarter the work on Task 3, char upgrading, was in two areas; upgrading Penelec char made from Penelec filter cake to blast furnace formed coke, and evaluating various bituminous pitch binders. The formed coke from Penelec filter cake was of good quality with a high crush strength of 3000 pounds. The reactivity was not equal to that of conventional coke but it is felt that it could be made to equal conventional coke with further study, specifically by adding binder coal to the raw material recipe. The work evaluating bituminous pitch binders confirmed earlier thinking that will bemore » valuable to a commercial scale-up. Asphalt binders are compatible with coal tar binders and produce a coke of equal quality. Hence asphalt binders can be used to supply deficiencies of tar production in units employing coals with insufficient volatile matter to supply enough tar for the coking process. Asphalt binders have about a 50% savings from coal tar pitch. During the 4th Quarter of 1991, a total of 15 Continuous Mild Gasification Unit (CMGU) test runs were made. Efforts continued to determine the optimum forward/reverse ratio to maximize coal feed rate. The success of these efforts has been limited with a maximum coal feed rate of 400 lbs/hr obtainable with a caking coal. The handicap of not having screw shaft heaters cannot be overcome by adjustment of the forward/reverse ratio.« less

Development of an advanced, continuous mild gasification process for the production of co-products

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Neal, G.W.

1991-01-01

During this quarter the work on Task 3, char upgrading, was in two areas; upgrading Penelec char made from Penelec filter cake to blast furnace formed coke, and evaluating various bituminous pitch binders. The formed coke from Penelec filter cake was of good quality with a high crush strength of 3000 pounds. The reactivity was not equal to that of conventional coke but it is felt that it could be made to equal conventional coke with further study, specifically by adding binder coal to the raw material recipe. The work evaluating bituminous pitch binders confirmed earlier thinking that will bemore » valuable to a commercial scale-up. Asphalt binders are compatible with coal tar binders and produce a coke of equal quality. Hence asphalt binders can be used to supply deficiencies of tar production in units employing coals with insufficient volatile matter to supply enough tar for the coking process. Asphalt binders have about a 50% savings from coal tar pitch. During the 4th Quarter of 1991, a total of 15 Continuous Mild Gasification Unit (CMGU) test runs were made. Efforts continued to determine the optimum forward/reverse ratio to maximize coal feed rate. The success of these efforts has been limited with a maximum coal feed rate of 400 lbs/hr obtainable with a caking coal. The handicap of not having screw shaft heaters cannot be overcome by adjustment of the forward/reverse ratio.« less

Interpretation of a leak-off test conducted near the bottom of the Kumano Forearc Basin strata at IODP Site C0002 in the Nankai accretionary complex, SW Japan

NASA Astrophysics Data System (ADS)

Song, I.; Huepers, A.; Olcott, K. A.; Saffer, D. M.; Dugan, B.; Strasser, M.

2013-12-01

The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) is a long-term, multi-stage scientific drilling project launched for investigating fault mechanics and seismogenesis along subduction megathrusts. One main key to the mechanics of the plate boundary is understanding the absolute mechanical strength and the in situ stress along the megathrust. As part of efforts to access the Nankai Trough seismogenic zone, the NanTroSEIZE Integrated Ocean Drilling Program (IODP) project began riser-based drilling operations at Site C0002 (Hole C0002F) in 2010 during IODP Expedition 326, with the objective of reaching the plate interface at ~6800 meters below the seafloor (mbsf). The geology in this area is composed of the Kumano Forearc Basin sedimentary strata to ~940 mbsf, underlain by the inner accretionary wedge. IODP Expedition 326 drilled Hole C0002F to 872.5 mbsf, near the bottom of the Kumano Basin, and set a 20-inch casing string to 860.2 mbsf. During IODP Expedition 338 in 2012, the hole was extended to 2005.5 mbsf. At the beginning of the operation, a leak-off test (LOT) was conducted in the interval of 872.5-875.5 mbsf, to define the maximum mud weight for the next stage of logging-while-drilling (LWD). Drilling-out-cement (DOC) at the bottom of the hole prior to the LOT provided a 3-m long, 17-inch diameter open borehole for the LOT. For the LOT, this open hole interval was pressurized with the outer annulus closed by the blow out preventer (BOP) using drilling mud of density of 1100 kg/m3, and mud pressure was measured at the cement pumps. The bottom-hole pressure was calculated by the recorded pressure plus the static pressure of the mud column. The first cycle of pressurization was conducted with injection of drilling mud at 31.8 l/min. However, the leak-off pressure (LOP) was not clearly defined because a large volume of mud was lost. Therefore a second cycle was conducted with a higher drilling mud injection rate (47.7 l /min). The rapid increase in pressure with a lower volume of mud injected during the second cycle suggests that a good mud cake was formed around the borehole wall, possibly due to mud flowing into the formation during the first cycle. In the second cycle, we identify a LOP of ~32.0 MPa from the pressure-volume record, which we interpret as the least principal stress. The total vertical stress given by the integration of bulk density with respect to depth is 35.7 MPa, indicating that the LOP reflects the least horizontal stress. This result can be a solid basis to constrain the in situ state of stress from indirect stress indicators such as wellbore failures at other depths.

Preliminary study on filamentous particle distribution in septic tank effluent and their impact on filter cake development.

PubMed

Spychała, Marcin; Nieć, Jakub; Pawlak, Maciej

2013-01-01

In this paper, the preliminary study on the impact of filamentous particles (FP) in the septic tank effluent (STE) on filter cake (FC) development was presented. The number, length and diameter (30 p./cm3, 451 and 121 microm, respectively, on average) of FPs were measured using microscope image analysis of STE samples condensed using a vacuum evaporation set. Results of this study showed, that 0.73% of volatile suspended solids (VSSs) mass from the STE occurs in the form of FPs. No correlation between FP total mass and VSS was found. An experiment with a layer of FPs simulated by ground toilet paper was conducted and showed the impact of this layer (4.89 mg/cm2) on wastewater hydraulic conductivity--for an FC with FPs (FC-FP), hydraulic conductivity was seven times lower than for the FC without the FP layer, and on outflow quality (lower concentration of organic matter expressed as chemical oxygen demand (COD) in effluent from the FC-FP filter than in the effluent from the FC filter: 618 and 732 gO2/m3, respectively). Despite a relatively small amount of FPs in STE solids (as volume fraction), they play an important role in FC development due to their relatively high length and low degradability. Probably relatively small pores of the FC containing FPs (FC-FP) caused a small particle blocking and a decrease in permeability.

Preparation of a concentrated organophyllosilicate and nanocomposite composition

DOEpatents

Chaiko, David J.; Niyogi, Suhas G.

2007-01-16

The present invention provide methods for producing a low moisture organophyllosilicate composition using monomers, oligomers, or polymers to displace water associated with the organophyllosilicates in an aqueous organophyllosilicate slurry or filter cake. The invention additionally provides methods for producing organophyllosilicate nanocomposites from the concentrated organophyllosilicate compositions by dispersing the compositions in a polymer matrix.

40 CFR Appendix I to Part 265 - Recordkeeping Instructions

Code of Federal Regulations, 2010 CFR

2010-07-01

... physical form, i.e., liquid, sludge, solid, or contained gas. If the waste is not listed in part 261..., solid filter cake from production of ___, EPA Hazardous Waste Number W051). Each hazardous waste listed... technique(s) used at the facility to treat, store or dispose of each quantity of hazardous waste received. 1...

Optimization of hydrolysis and volatile fatty acids production from sugarcane filter cake: Effects of urea supplementation and sodium hydroxide pretreatment.

PubMed

Janke, Leandro; Leite, Athaydes; Batista, Karla; Weinrich, Sören; Sträuber, Heike; Nikolausz, Marcell; Nelles, Michael; Stinner, Walter

2016-01-01

Different methods for optimization the anaerobic digestion (AD) of sugarcane filter cake (FC) with a special focus on volatile fatty acids (VFA) production were studied. Sodium hydroxide (NaOH) pretreatment at different concentrations was investigated in batch experiments and the cumulative methane yields fitted to a dual-pool two-step model to provide an initial assessment on AD. The effects of nitrogen supplementation in form of urea and NaOH pretreatment for improved VFA production were evaluated in a semi-continuously operated reactor as well. The results indicated that higher NaOH concentrations during pretreatment accelerated the AD process and increased methane production in batch experiments. Nitrogen supplementation resulted in a VFA loss due to methane formation by buffering the pH value at nearly neutral conditions (∼ 6.7). However, the alkaline pretreatment with 6g NaOH/100g FCFM improved both the COD solubilization and the VFA yield by 37%, mainly consisted by n-butyric and acetic acids. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study of the pyrolysis of sludge and sludge/disposal filter cake mix for the production of value added products.

PubMed

Velghe, Inge; Carleer, Robert; Yperman, Jan; Schreurs, Sonja

2013-04-01

Slow and fast pyrolysis of sludge and sludge/disposal filter cake (FC) mix are performed to investigate the liquid and solid products for their use as value added products. The obtained slow pyrolysis liquid products separate in an oil, a water rich fraction and a valuable crystalline solid 5,5-dimethyl hydantoin. During fast pyrolysis, mainly an oil fraction is formed. Aliphatic acids and amides present in the water rich fractions can be considered as value added products and could be purified. The oil fractions have properties which make them promising as fuel (25-35 MJ/kg, 14-20 wt% water content, 0.2-0.6 O/C value), but upgrading is necessary. Sludge/FC oils have a lower calorific value, due to evaporation of alcohols present in FC. ICP-AES analyses reveal that almost none of the metals present in sludge or sludge/FC are transferred towards the liquid fractions. The metals are enriched in the solid fractions. Copyright © 2013 Elsevier Ltd. All rights reserved.

EVAPORATOR FLOOR, CELL ONE IN FOREGROUND, CRYSTALLIZER MEZZANINE TO REAR, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

EVAPORATOR FLOOR, CELL ONE IN FOREGROUND, CRYSTALLIZER MEZZANINE TO REAR, OLIVER MUD FILTER WING TO RIGHT REAR. VIEW FROM NORTHEAST - Lihue Plantation Company, Sugar Mill Building, Haleko Road, Lihue, Kauai County, HI

Coal-water slurries containing petrochemicals to solve problems of air pollution by coal thermal power stations and boiler plants: An introductory review.

PubMed

Dmitrienko, Margarita A; Strizhak, Pavel A

2018-02-01

This introductory study presents the analysis of the environmental, economic and energy performance indicators of burning high-potential coal water slurries containing petrochemicals (CWSP) instead of coal, fuel oil, and natural gas at typical thermal power stations (TPS) and a boiler plant. We focus on the most hazardous anthropogenic emissions of coal power industry: sulfur and nitrogen oxides. The research findings show that these emissions may be several times lower if coal and oil processing wastes are mixed with water as compared to the combustion of traditional pulverized coal, even of high grades. The study focuses on wastes, such as filter cakes, oil sludge, waste industrial oils, heavy coal-tar products, resins, etc., that are produced and stored in abundance. Their deep conversion is very rare due to low economic benefit. Effective ways are necessary to recover such industrial wastes. We present the cost assessment of the changes to the heat and power generation technologies that are required from typical power plants for switching from coal, fuel oil and natural gas to CWSPs based on coal and oil processing wastes. The corresponding technological changes pay off after a short time, ranging from several months to several years. The most promising components for CWSP production have been identified, which provide payback within a year. Among these are filter cakes (coal processing wastes), which are produced as a ready-made coal-water slurry fuel (a mixture of flocculants, water, and fine coal dust). These fuels have the least impact on the environment in terms of the emissions of sulfur and nitrogen oxides as well as fly ash. An important conclusion of the study is that using CWSPs based on filter cakes is worthwhile both as the main fuel for thermal power stations and boiler plants and as starting fuel. Copyright © 2017 Elsevier B.V. All rights reserved.

[Improvement of municipal sewage sludge dewaterability by bioleaching: a pilot-scale study with a continuous plug flow reaction model].

PubMed

Liu, Fen-Wu; Zhou, Li-Xiang; Zhou, Jun; Jiang, Feng

2011-10-01

A plug-flow bio-reactor of 700 L working volume for sludge bioleaching was used in this study. The reactor was operationally divided into six sections along the direction of the sludge movement. Ten duration of continuous operation of sludge bioleaching with Acidibacillus spp. and 1.2 m3 x h(-1) aeration amount was conducted. In this system, sludge retention time was 2.5 d, and the added amount of microbial nutritional substance was 4 g x L(-1). During sludge bioleaching, the dynamic changes of pH, dewaterability (specific resistance to filtration, SRF) of sewage sludge in different sections, the moisture content and moisture evaporation rate of dewatered bioleached sludge cake obtained by chamber filter press were investigated. The results showed that the SRF of sludge significantly decreased from initial 1.50 x 10(13) m x kg(-1) to the final 0.34 x 10(13) m x kg(-1). The wasted bioleached sludge was collected and dewatered by chamber filter press under the following pressures as 0.3 MPa for 4 h (2 h for feeding sludge, 2 h for holding pressure), 3 h (1.5 h for feeding sludge, 1.5 h for holding pressure), 2 h (1 h for feeding sludge, 1 h for holding pressure), and 1 h (0.5 h for feeding sludge, 0.5 h for holding pressure). Correspondingly, the moisture of dewatered sludge was reduced to 57.9%, 59.2%, 59.6%, and 63.4% of initial moisture, respectively. Moreover, the moisture content of bioleached sludge cake was reduced to about 45% and less than 10% if the cake was placed at 25 degrees C for 15 h and 96 h, respectively. Obviously, sludge bioleaching followed by sludge dewatering using chamber filter press is a promising attractive approach for sludge half-dryness treatment in engineering application.

Extraction of gelatin from catfish bone using NaOH and its utilization as a template on mesoporous silica alumina

NASA Astrophysics Data System (ADS)

Nuryanto, R.; Trisunaryanti, W.; Falah, I. I.; Triyono

2018-04-01

Gelatin extraction from catfish bone using NaOH and its utilization as a template on a synthesis of mesoporous silica-alumina had been investigated. The extraction was prepared by immersing 25 g catfish bone in 125 mL of NaOH in concentration of 0.0; 0.05; 0.10; 0.15 and 0.20 M for 24 h, then washing with demineralized water until pH 7, followed by immersed the bone into 125 mL of 1 M HCl for 1 h, then washed using demineralized water into pH 5. To produce gelatin the bone was refluxed with 100 mL demineralized water at 70°C for 5 h then evaporated at 50°C. The dry gelatin was characterized using FTIR and electrophoresis (SDS-PAGE). The best performance of gelatin was produced by NaOH 0.10 M. The gelatin consists of amide A, B, I, II, III and molecular weight of 25-200kDa. Silica and Alumina material prepared from Lapindo mud extraction. Dry Lapindo mud crushed and filtered until pass 100 mesh, then reflux using 6 M HCl (1:4 w/V) at 90°C for 5h then filtered. The filtrate was consisting alumina solution adding with 6 M NaOH (2/3 V/V) them filtered. The filtrate then injected by CO2 gas for 30 minutes and filtered, the residue was calcined at 500°C for 5h. The residual of Lapindo mud dried and refluxed with 6 M NaOH (1:4 w/v) at 90 °C. After 5h filtered and the filtrate added by HCl to pH 8 and filtered, the residual then dried. The Si and Al were then analyzed by XRF and consist of silica and alumina for 99.1 and 87.73%, respectively. Silica-alumina was prepared using silica and alumina extracted from Lapindo mud. 6 g of SiO2 and 2 g of NaOH was immersed in 62 mL of demineralized water then added with alumina solution (0.204 g alumina in 30 mL demineralized water). The gelatin solution (5 g gelatin in 70 mL demineralized water) was dropped into the silica-alumina while stirring at 50°C for 4 h and aging for 24 h. The synthesized silica alumina was analysed using FTIR and surface area analyser. The FT-IR spectra indicated the TO4 (T=Si, Al) vibration at wave number of 1049.28 and 1103.23 cm-1. The synthesized silica-alumina showed mesoporous characters with a pore diameter of 41.18 nm and surface area of 32.76 m2/g

Effects of mineral amendments on trace elements leaching from pre-treated marine sediment after simulated rainfall events.

PubMed

Hurel, C; Taneez, M; Volpi Ghirardini, A; Libralato, G

2017-01-01

Bauxite extraction by-products (red mud) were used to evaluate their potential ability to stabilize trace elements from dredged and aerated/humidified marine sediment. The investigated by-products were: bauxaline ® (BX) that is a press-filtered red mud; bauxsol™(BS) that is a press-filtered red mud previously washed with excess of seawater, and gypsum neutralized bauxaline ® (GBX). These materials were separately mixed to dredged composted sediment sample considering 5% and 20% sediment: stabilizer ratios. For pilot experiments, rainfall events were regularly simulated for 3 months. Concentrations of As, Mo, Cd, Cr, Zn, Cu, and Ni were analyzed in collected leachates as well as toxicity. Results showed that Cd, Mo, Zn, and Cu were efficiently stabilized in the solid matrix when 20% of BX, BS, and GBX was applied. Consequently, toxicity of leachates was lower than for the untreated sediment, meaning that contaminants mobility was reduced. A 5% GBX was also efficient for Mo, Zn and Cu stabilization. In all scenarios, As stabilization was not improved. Compared to all other monitored elements, Mo mobility seemed to depend upon temperature-humidity conditions during pilot experiments suggesting the need of further investigations. Copyright © 2016 Elsevier Ltd. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sievers, David A.; Lischeske, James J.; Biddy, Mary J.

Solid-liquid separation of intermediate process slurries is required in some process configurations for the conversion of lignocellulosic biomass to transportation fuels. Thermochemically pretreated and enzymatically hydrolyzed corn stover slurries have proven difficult to filter due to formation of very low permeability cakes that are rich in lignin. Treatment of two different slurries with polyelectrolyte flocculant was demonstrated to increase mean particle size and filterability. Filtration flux was greatly improved, and thus scaled filter unit capacity was increased approximately 40-fold compared with unflocculated slurry. Although additional costs were accrued using polyelectrolyte, techno-economic analysis revealed that the increase in filter capacity significantlymore » reduced overall production costs. Fuel production cost at 95% sugar recovery was reduced by $1.35 US per gallon gasoline equivalent for dilute-acid pretreated and enzymatically hydrolyzed slurries and $3.40 for slurries produced using an additional alkaline de-acetylation preprocessing step that is even more difficult to natively filter.« less

Selection of Yarrowia lipolytica strains with high protein content from yeasts isolated from different marine environments

NASA Astrophysics Data System (ADS)

Chi, Zhenming; Wang, Fang; Wang, Lin; Li, Jing; Wang, Xianghong

2007-10-01

A total of 78 Yarrowia lipolytica yeast strains from seawater, sediments, mud of salterns, the guts of marine fish, and marine algae were obtained. After the crude protein of the yeasts was estimated by the method of Kjehldahl, we found that seven strains of the marine yeasts grown in soy bean cake hydrolysate with 20 g L-1 of glucose for 48 h at 28°C contained more than 41.0 g protein per 100 g of cell dry weight and the cell dry weight was more than 4.4 g per L of the culture. Among them, strain SWJ-1b contained the highest crude protein. The results of Biolog identification and molecular methods further confirmed that they indeed belonged to Y. lipolytica.

Isolation and Identification of Acholeplasma sp. from the Mud Crab, Scylla serrata

PubMed Central

Chen, Ji-Gang; Lou, Dan; Yang, Ji-Fang

2011-01-01

For the first time, a mollicute-like organism (MLO) was cultured from moribund mud crabs (Scylla serrata) during an outbreak of clearwater disease in Zhejiang Province, China. The MLO displayed a fried-egg colony morphology in culture, did not possess a cell wall, and was not retained by 0.45 μm and 0.2 μm filters. It was able to ferment glucose, sucrose, lactose, and maltose, but it did not utilize arginine and urea. The MLO grew in the absence of bovine serum and was not susceptible to digitonin. Sequence analysis of the 16S rRNA gene revealed that this MLO had 99% identity with Acholeplasma laidlawii PG-8A, which indicates that the organism isolated from mud crabs is a member of the genus Acholeplasma. PMID:21808652

Spectrophotometric determination of fluorine in silicate rocks

USGS Publications Warehouse

Peck, L.C.; Smith, V.C.

1964-01-01

The rock powder is sintered with a sodium carbonate flux containing zinc oxide and magnesium carbonate, the sinter-cake leached with water and the resulting solution filtered. Fluorine is separated from the acidified filtrate by steam distillation and determined spectrophotometrically by means of a zirconium-SPADNS reagent. If a multiple-unit distillation apparatus is used, 12 determinations can be completed per man-day. ?? 1964.

Chemical characteristics of ambient aerosols contributed by cooking process at Noorpur village near Delhi (India)

NASA Astrophysics Data System (ADS)

Singh, Sudha; Kumar, Bablu; Gupta, Gyan Prakash; Kulshrestha, U. C.

2013-05-01

Combustion of fuels such as wood, crop residue and dung cakes etc. is one of the major sources of air pollution in developing countries. These fuels are still used commonly for cooking purpose in rural India. This study investigates the chemical composition of the ambient aerosols during cooking hours at a village called Noorpur (28.470 N, 77.030 E) which lies near Delhi city. Aerosol sampling was carried out during August 2011-May 2012 by using handy sampler (Envirotech model APM 821) installed at the terrace of a building (˜6m). The samples were collected on 8 hourly basis using Teflon filters. The water extract of these filters was analyzed for major anions (F-, Cl-, NO3-, SO42-) and major cations (Na+, NH4+, K+, Ca2+ Mg2+) by ion chromatography (Metrohm 883 Basic IC Plus). Results highlighted that cooking process contributed significant amount of SO42- and K+ṡ. Biomass burning is considered as a potential source of K+ in air. The high concentration of SO42- might be due to oxidation of SO2 contributed by the combustion of dung cakes. Further, the detailed results will be discussed during the conference.

Application of electro acoustics for dewatering pharmaceutical sludge

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golla, P.S.; Johnson, H.W.

1992-02-01

Application of electro acoustic principles for dewatering has been developed by Battelle Institute. The Department of Energy, Battelle Institute, and Ashbrook-Simon-Hartley, have jointly developed an Electro Acoustic Dewatering press (EAD press). The EAD press applies a combination of mechanical pressure, electrical current and ultrasonics. This press is utilized after conventional dewatering devices and can remove up to 50% water from filtered sludge cake at a fraction of the cost incurred in existing thermal drying devices. The dominant mechanism of sludge dewatering by EAD press is electro-osmosis due to the application of a direct current field. Electro-osmosis is caused by anmore » electrical double layer of oppositely charged ions formed at the solid liquid interface, which is characterized by zeta potential. The ultrasonic fields help electro-osmosis by consolidation of the filter cake and by release of inaccessible liquid. The EAD press has been tested successfully on a variety of materials including apple pomace, corn gluten, sewage sludge, and coal fines. A three week long full scale trial was conducted successfully at a pharmaceutical industry to determine the application of this technology for dewatering waste activated sludge.« less

Phosphatase activity and its relationship with physical and chemical parameters during vermicomposting of filter cake and cattle manure.

PubMed

Busato, Jader Galba; Papa, Gabriella; Canellas, Luciano Pasqualoto; Adani, Fabrizio; de Oliveira, Aline Lima; Leão, Tairone Paiva

2016-03-15

Recycling of phosphorus (P) from organic residues (ORs) is important to develop environmentally friendly agriculture. The use of this P source depends on phosphatase enzymes, which can be affected by a chain of parameters during maturation of ORs. In this study the phosphatase activity levels throughout vermicomposting of filter cake (FC) and cattle manure (CM) were correlated with different physical and chemical parameters in an effort to increase the knowledge about recycling of P from ORs. FC presented higher total nitrogen content (TNC), total organic carbon (TOC), humic acid (HA) content, water-soluble P (WSP), phosphatase activities and nanopore volume than CM during vermicomposting. Decreases in TOC of CM resulted from carbohydrate mineralization, which was not observed for FC. CM showed increased hydrophobic index during vermicomposting while FC showed a slight decrease. Phosphatase activities correlated positively with TOC, pH and WSP and negatively with HA content for both vermicomposts. Nanopore volume was negatively correlated with phosphatase activities for FC but not for CM. No correlations between hydrophobicity and phosphatase activities were found for FC. Increased hydrophobicity throughout vermicomposting of CM could be partially associated with decreases in phosphatase levels. © 2015 Society of Chemical Industry.

Bioconversion of petroleum hydrocarbons in soil using apple filter cake

PubMed Central

Medaura, M. Cecilia; Ércoli, Eduardo C.

2008-01-01

The aim of this study was to investigate the feasibility of using apple filter cake, a fruit-processing waste to enhance the bioremediation of petroleum contaminated soil. A rotating barrel system was used to study the bioconversion of the xenobiotic compound by natural occurring microbial population. The soil had been accidentally polluted with a total petroleum hydrocarbon concentration of 41,000 ppm. Although this global value was maintained during the process, microbial intervention was evidenced through transformation of the petroleum fractions. Thus, fractions that represent a risk for the environment (GRO, Gasoline Range Organics i.e., C6 to C10–12; DRO, Diesel Range Organics i.e., C8–12 to C24–26 and RRO, Residual Range Organics i.e., C25 to C35) were significantly reduced, from 2.95% to 1.39%. On the contrary, heavier weight fraction from C35 plus other organics increased in value from 1.15% to 3.00%. The noticeable diminution of low molecular weight hydrocarbons content and hence environmental risk by the process plus the improvement of the physical characteristics of the soil, are promising results with regard to future application at large scale. PMID:24031241

JPL Activated Carbon Treatment System (ACTS) for sewage

NASA Technical Reports Server (NTRS)

1976-01-01

An Activated Carbon Treatment System (ACTS) was developed for sewage treatment and is being applied to a one-million gallon per day sewage treatment pilot plant in Orange County California. Activities reported include pyrolysis and activation of carbon-sewage sludge, and activated carbon treatment of sewage to meet ocean discharge standards. The ACTS Sewage treatment operations include carbon-sewage treatment, primary and secondary clarifiers, gravity (multi-media) filter, filter press dewatering, flash drying of carbon-sewage filter cake, and sludge pyrolysis and activation. Tests were conducted on a laboratory scale, 10,000 gallon per day demonstration plant and pilot test equipment. Preliminary economic studies are favorable to the ACTS process relative to activated sludge treatment for a 175,000,000 gallon per day sewage treatment plant.

Comparison of different options for harvest of a therapeutic protein product from high cell density yeast fermentation broth.

PubMed

Wang, Alice; Lewus, Rachael; Rathore, Anurag S

2006-05-05

Recovery of therapeutic protein from high cell density yeast fermentations at commercial scale is a challenging task. In this study, we investigate and compare three different harvest approaches, namely centrifugation followed by depth filtration, centrifugation followed by filter-aid enhanced depth filtration, and microfiltration. This is achieved by presenting a case study involving recovery of a therapeutic protein from Pichia pastoris fermentation broth. The focus of this study is on performance of the depth filtration and the microfiltration steps. The experimental data has been fitted to the conventional models for cake filtration to evaluate specific cake resistance and cake compressibility. In the case of microfiltration, the experimental data agrees well with flux predicted by shear induced diffusion model. It is shown that, under optimal conditions, all three options can deliver the desired product recovery ( >80%), harvest time ( <15 h including sequential concentration/diafiltration step), and clarification ( <6 NTU). However, the three options differ in terms of process development time required, capital cost, consumable cost, ease of scale-ability and process robustness. It is recommended that these be kept under consideration when making a final decision on a harvesting approach.

[Influence of non-ionic surfactants on sludge dewaterability].

PubMed

Hou, Hai-Pan; Pu, Wen-Hong; Shi, Ya-Fei; Yu, Wen-Hua; Fan, Ming-Ming; Liu, Huan; Yang, Chang-Zhu; Li, Ye; Yang, Jia-Kuan

2012-06-01

The water content of dewatered sludge cake decreases to about 80% by current sludge dewatering technologies, which hardly satisfies the stricter standards of sludge disposal. In order to evaluate the effects of non-ionic surfactants on sludge dewaterability, two kinds of non-ionic surfactants (OPEO and APG) were studied by using two evaluation indexes, i. e. , specific resistance to filtration (SRF) and dewatering efficiency. Moreover, morphologies of conditioned sewage sludge and raw sludge were comparatively investigated. Results showed that non-ionic surfactants can decrease the particle size of sewage sludge floc and generate more homogenous and regular shape, and then improve the dewatering efficiency. APG has better effect on sewage sludge dewatering than OPEO. SRF of conditioned sludge with APG dosage of 0.05% DS decreased to 42% of SRF of raw sludge, and its dewatering efficiency was as high as 93%. Plate-frame pressure filter experiment demonstrated that, the water content of dewatered cake conditioned with APG dosage of 0.05% DS was lower by about 10% than that of dewatered cake without APG, and its dewatering efficiency reached 97%. Therefore, this research provides some reference for the application of APG in sludge dewatering.

Behavior of micro-particles in monolith ceramic membrane filtration with pre-coagulation.

PubMed

Yonekawa, H; Tomita, Y; Watanabe, Y

2004-01-01

This paper is intended to clarify the characteristics unique to monolith ceramic membranes with pre-coagulation by referring to the behavior of micro-particles. Flow analysis and experiments have proved that monolith ceramic membranes show a unique flow pattern in the channels within the element, causing extremely rapid flocculation in the channel during dead-end filtration. It was assumed that charge-neutralized micro-particles concentrated near the membrane surface grow in size due to flocculation, and as a result, coarse micro-particles were taken up by the shearing force to flow out. As the dead end points of flow in all the channels are located near the end of the channels with higher filterability, most of the flocculated coarse particles are formed to a columnar cake intensively at the dead end point. Therefore cake layer forming on the membrane other than around the dead end point is alleviated. This behavior of particle flocculation and cake formation at the dead end point within the channels are unique characteristics of monolith ceramic membranes. This is why all monolith ceramic membrane water purification systems operating in Japan do not have pretreatment equipment for flocculation and sedimentation.

Visual Temporal Filtering and Intermittent Visual Displays.

DTIC Science & Technology

1986-08-08

suport Mud Kaplan, Associate Professor, 20% time and effort Michelangelo ROssetto, Research Associate, 20% time and m4pport Margo Greene, Research...reached and are described as follows. The variable raster rate display was designed and built by Michelangelo R0ssetto and Norman Milkman, Research

Real Time Mud Gas Logging During Drilling of DFDP-2B

NASA Astrophysics Data System (ADS)

Mathewson, L. A.; Toy, V.; Menzies, C. D.; Zimmer, M.; Erzinger, J.; Niedermann, S.; Cox, S.

2015-12-01

The Deep Fault Drilling Project (DFDP) aims to improve our understanding of the Alpine Fault Zone, a tectonically active mature fault system in New Zealand known to rupture in large events, by deep scientific drilling. The borehole DFDP-2B approached the Alpine Fault at depth, reaching a final depth of 892 m (820 m true vertical depth). Online gas analysis (OLGA) while drilling tracked changes in the composition of gases extracted from the circulating drill mud. The composition of fluids from fault zones can provide information about their origins, flow rates and -paths, fluid-rock interactions along these paths, and the permeability structure of the faulted rock mass. Apart from an atmospheric input, the gases in drilling mud derive from the pore space of rock, crushed at the drill bit, and from permeable layers intersected by the borehole. The rapid formation of mud wall cake seals the borehole from further fluid inflow, hence formation-derived gases enter mostly at the depth of the drill bit. OLGA analyses N2, O2, Ar, CO2, CH4, He, and H2 on a mass spectrometer, hydrocarbons CH4, C2H6, C3H8, i-C4H10, and n-C4H10 on a gas chromatograph, and Rn using a lucas-cell detector. Gas was sampled for offline analyses on noble gas and stable isotopes to complement the OLGA dataset. The principle formation-derived gases found in drilling mud during drilling of DFDP-2 were CO2 and CH4, with smaller component of H2 and He2. High radon activity is interpreted to reflect intervals of active fluid flow through highly fractured and faulted rock. 3He/4He values in many samples were extremely air-contaminated, i.e. there was almost no excess of non-atmospheric He. The 3He/4He values measured at 236 m and 610 m, which are the only analyses with uncertainties <100%, are very similar to those measured in hot springs along the Alpine Fault, e.g. Fox River (0.64 Ra), Copland (0.42 Ra), Lower Wanganui (0.81 Ra). We will compare these data to those gathered using OLGA and discuss the implications.

Pelletizing/reslurrying as a means of distributing and firing clean coal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conkle, H.N.; Raghavan, J.K.; Smit, F.J.

1991-11-21

The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be reslurried into Coal water fuels (CWF) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines. The project includes preparing coal pellets and capsules from wet filter cake that can be economically stored, handled, transported, and reslurried into a CWF that can be suitably atomized and fired at the user site. The wet cakes studied were prepared from ultra-fine (95% -325 mesh) coal beneficiated by advanced froth-flotation techniques. The coalsmore » studied included two eastern bituminous coals, one from Virginia (Elkhorn) and one from Illinois (Illinois No. 6) and one western bituminous coal from Utah (Sky Line coal).« less

Radiochemical Analyses of the Filter Cake, Granular Activated Carbon, and Treated Ground Water from the DTSC Stringfellow Superfund Site Pretreatment Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Esser, B K; McConachie, W; Fischer, R

2005-09-16

The Department of Toxic Substance Control (DTSC) requested that Lawrence Livermore National Laboratory (LLNL) evaluate the treatment process currently employed at the Department's Stringfellow Superfund Site Pretreatment Plant (PTP) site to determine if wastes originating from the site were properly managed with regards to their radioactivity. In order to evaluate the current management strategy, LLNL suggested that DTSC characterize the effluents from the waste treatment system for radionuclide content. A sampling plan was developed; samples were collected and analyzed for radioactive constituents. Following is brief summary of those results and what implications for waste characterization may be made. (1) Themore » sampling and analysis provides strong evidence that the radionuclides present are Naturally Occurring Radioactive Material (NORM). (2) The greatest source of radioactivity in the samples was naturally occurring uranium. The sample results indicate that the uranium concentration in the filter cake is higher than the Granular Activated Carbon (GAC) samples. (11 -14 and 2-6 ppm respectively). (3) No radiologic background for geologic materials has been established for the Stringfellow site, and comprehensive testing of the process stream has not been conducted. Without site-specific testing of geologic materials and waste process streams, it is not possible to conclude if filter cake and spent GAC samples contain radioactivity concentrated above natural background levels, or if radionuclides are being concentrated by the waste treatment process. Recommendation: The regulation of Technologically Enhanced, Naturally Occurring Radioactive Materials (T-NORM) is complex. Since the results of this study do not conclusively demonstrate that natural radioactive materials have not been concentrated by the treatment process it is recommended that the DTSC consult with the Department of Health Services (DHS) Radiological Health Branch to determine if any further action is warranted. If it were deemed desirable to establish a background for the Stringfellow setting LLNL would recommend that additional samples be taken and analyzed by LLNL using the same methods presented in this report.« less

A low-cost solid–liquid separation process for enzymatically hydrolyzed corn stover slurries

DOE PAGES

Sievers, David A.; Lischeske, James J.; Biddy, Mary J.; ...

2015-07-01

Solid-liquid separation of intermediate process slurries is required in some process configurations for the conversion of lignocellulosic biomass to transportation fuels. Thermochemically pretreated and enzymatically hydrolyzed corn stover slurries have proven difficult to filter due to formation of very low permeability cakes that are rich in lignin. Treatment of two different slurries with polyelectrolyte flocculant was demonstrated to increase mean particle size and filterability. Filtration flux was greatly improved, and thus scaled filter unit capacity was increased approximately 40-fold compared with unflocculated slurry. Although additional costs were accrued using polyelectrolyte, techno-economic analysis revealed that the increase in filter capacity significantlymore » reduced overall production costs. Fuel production cost at 95% sugar recovery was reduced by $1.35 US per gallon gasoline equivalent for dilute-acid pretreated and enzymatically hydrolyzed slurries and $3.40 for slurries produced using an additional alkaline de-acetylation preprocessing step that is even more difficult to natively filter.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sengupta, S.; Wong, K.V.; Nemerow, N.

Characterization of the following waste streams: air-classified light (ACL), digester slurry, filter cake, filtrate, washwater input and washwater effluent has been made for the Refcom facility in order to assess the effects of these waste streams, if discharged into the environment. Special laboratory studies to evaluate the effect of plastics on anaerobic digestion have been undertaken. A separate report has been furnished describing the studies of lab-model digesters. Data collected for ACL has been statistically analyzed.

Biogas Production from Sugarcane Waste: Assessment on Kinetic Challenges for Process Designing.

PubMed

Janke, Leandro; Leite, Athaydes; Nikolausz, Marcell; Schmidt, Thomas; Liebetrau, Jan; Nelles, Michael; Stinner, Walter

2015-08-31

Biogas production from sugarcane waste has large potential for energy generation, however, to enable the optimization of the anaerobic digestion (AD) process each substrate characteristic should be carefully evaluated. In this study, the kinetic challenges for biogas production from different types of sugarcane waste were assessed. Samples of vinasse, filter cake, bagasse, and straw were analyzed in terms of total and volatile solids, chemical oxygen demand, macronutrients, trace elements, and nutritional value. Biochemical methane potential assays were performed to evaluate the energy potential of the substrates according to different types of sugarcane plants. Methane yields varied considerably (5-181 Nm³·tonFM(-1)), mainly due to the different substrate characteristics and sugar and/or ethanol production processes. Therefore, for the optimization of AD on a large-scale, continuous stirred-tank reactor with long hydraulic retention times (>35 days) should be used for biogas production from bagasse and straw, coupled with pre-treatment process to enhance the degradation of the fibrous carbohydrates. Biomass immobilization systems are recommended in case vinasse is used as substrate, due to its low solid content, while filter cake could complement the biogas production from vinasse during the sugarcane offseason, providing a higher utilization of the biogas system during the entire year.

Biogas Production from Sugarcane Waste: Assessment on Kinetic Challenges for Process Designing

PubMed Central

Janke, Leandro; Leite, Athaydes; Nikolausz, Marcell; Schmidt, Thomas; Liebetrau, Jan; Nelles, Michael; Stinner, Walter

2015-01-01

Biogas production from sugarcane waste has large potential for energy generation, however, to enable the optimization of the anaerobic digestion (AD) process each substrate characteristic should be carefully evaluated. In this study, the kinetic challenges for biogas production from different types of sugarcane waste were assessed. Samples of vinasse, filter cake, bagasse, and straw were analyzed in terms of total and volatile solids, chemical oxygen demand, macronutrients, trace elements, and nutritional value. Biochemical methane potential assays were performed to evaluate the energy potential of the substrates according to different types of sugarcane plants. Methane yields varied considerably (5–181 Nm3·tonFM−1), mainly due to the different substrate characteristics and sugar and/or ethanol production processes. Therefore, for the optimization of AD on a large-scale, continuous stirred-tank reactor with long hydraulic retention times (>35 days) should be used for biogas production from bagasse and straw, coupled with pre-treatment process to enhance the degradation of the fibrous carbohydrates. Biomass immobilization systems are recommended in case vinasse is used as substrate, due to its low solid content, while filter cake could complement the biogas production from vinasse during the sugarcane offseason, providing a higher utilization of the biogas system during the entire year. PMID:26404248

Characteristics of flocs formed by polymer-only coagulation in water treatment and their impacts on the performance of downstream membrane separation.

PubMed

Maeng, Sung Kyu; Timmes, Thomas C; Kim, Hyun-Chul

2017-10-01

Two different quaternary amine polymers were examined as primary coagulants for the removal of natural organic matter (NOM) and concurrent production of flocs favorable for downstream membrane separation. The primary issue explored was the relationship between various coagulation conditions on the floc characteristics and the subsequent performance of microfiltration when filtering coagulated NOM. The size distribution and morphological properties of flocs formed through the coagulation of NOM were characterized and the effects of polymer type and dose on these characteristics were also examined. Coagulation of NOM using polydiallyldimethyl-ammonium chloride (pDADMAC) produced looser and less settleable flocs compared to dosing the equivalent amount of epichlorohydrin/dimethylamine (epi/DMA). This was associated with the formation of a relatively denser cake layer on the top of the membrane for the filtration of NOM coagulated with epi/DMA. The charge neutralization coagulation condition with the polymers removed almost all of the fouling tendency that had occurred when filtering raw NOM. The median diameter and the fractal dimension of the flocs produced increased as the zeta potential approached zero, which resulted in the formation of a cake layer that was easily removed from the surface of the membrane.

Assessment of contamination by percolation of septic tank effluent through natural and amended soils.

PubMed

Cheung, K C; Venkitachalam, T H

2004-01-01

Fly ash has been found to be a potential material for the treatment of municipal and industrial wastewater, and may be useful in the treatment of septic tank effluent. Laboratory columns (30 cm) were used to determine the sorption capacity and hydraulic properties of lagoon fly ash, loamy sand, sand, and sand amended by lagoon fly ash (30 and 60%) and red mud gypsum (20%). The removal of chemical oxygen demand (COD) was high in all column effluents (71-93%). Extent of nitrification was high in Spearwood sand, Merribrook loamy sand and 20% red mud gypsum amended Spearwood sand. However, actual removal of nitrogen (N) was high in columns containing lagoon fly ash. Unamended Spearwood sand possessed only minimal capacity for P sorption. Merribrook loamy sand and red mud gypsum amended sand affected complete P removal throughout the study period of 12 weeks. Significant P leakage occurred from lagoon fly ash amended sand columns following 6-10 weeks of operation. Neither lagoon fly ash nor red mud gypsum caused any studied heavy metal contamination including manganese (Mn), lead (Pb), zinc (Zn), cadmium (Cd) and chromium (Cr) of effluent. It can be concluded that Merribrook loamy sand is better natural soil than Spearwood sand as a filter medium. The addition of lagoon fly ash enhanced the removal of P in Spearwood sand but the efficiency was lower than with red mud gypsum amendment.

Microfluidic colloid filtration

PubMed Central

Linkhorst, John; Beckmann, Torsten; Go, Dennis; Kuehne, Alexander J. C.; Wessling, Matthias

2016-01-01

Filtration of natural and colloidal matter is an essential process in today’s water treatment processes. The colloidal matter is retained with the help of micro- and nanoporous synthetic membranes. Colloids are retained in a “cake layer” – often coined fouling layer. Membrane fouling is the most substantial problem in membrane filtration: colloidal and natural matter build-up leads to an increasing resistance and thus decreasing water transport rate through the membrane. Theoretical models exist to describe macroscopically the hydrodynamic resistance of such transport and rejection phenomena; however, visualization of the various phenomena occurring during colloid retention is extremely demanding. Here we present a microfluidics based methodology to follow filter cake build up as well as transport phenomena occuring inside of the fouling layer. The microfluidic colloidal filtration methodology enables the study of complex colloidal jamming, crystallization and melting processes as well as translocation at the single particle level. PMID:26927706

Molecular characteristics of humic acids isolated from vermicomposts and their relationship to bioactivity.

PubMed

Martinez-Balmori, Dariellys; Spaccini, Riccardo; Aguiar, Natália Oliveira; Novotny, Etelvino Henrique; Olivares, Fábio Lopes; Canellas, Luciano Pasqualoto

2014-11-26

Vermitechnology is an effective composting method, which transforms biomass into nutrient-rich organic fertilizer. Mature vermicompost is a renewable organic product containing humic substances with high biological activity. The aim of this study was to assess the chemical characteristics and the bioactivity of humic acids isolated from different vermicomposts produced with either cattle manure, sugar cane bagasse, sunflower cake from seed oil extraction, or filter cake from a sugar cane factory. More than 200 different molecules were found, and it was possible to identify chemical markers on humic acids according to the nature of the organic source. The large hydrophobic character of humic extracts and the preservation of altered lignin derivatives confer to humic acids the ability to induce lateral root emergence in maize seedlings. Humic acid-like substances extracted from plant biomass residues represent an additional valuable product of vermicomposting that can be used as a plant growth promoter.

Pelletizing/reslurrying as a means of distributing and firing clean coal. Final quarterly technical progress report No. 5, July 1, 1991--September 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Conkle, H.N.; Raghavan, J.K.; Smit, F.J.

1991-11-21

The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be reslurried into Coal water fuels (CWF) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines. The project includes preparing coal pellets and capsules from wet filter cake that can be economically stored, handled, transported, and reslurried into a CWF that can be suitably atomized and fired at the user site. The wet cakes studied were prepared from ultra-fine (95% -325 mesh) coal beneficiated by advanced froth-flotation techniques. The coalsmore » studied included two eastern bituminous coals, one from Virginia (Elkhorn) and one from Illinois (Illinois No. 6) and one western bituminous coal from Utah (Sky Line coal).« less

Optimization of the cleaning process on a pilot filtration setup for waste water treatment accompanied by flow visualization

NASA Astrophysics Data System (ADS)

Bílek, Petr; Hrůza, Jakub

2018-06-01

This paper deals with an optimization of the cleaning process on a liquid flat-sheet filter accompanied by visualization of the inlet side of a filter. The cleaning process has a crucial impact on the hydrodynamic properties of flat-sheet filters. Cleaning methods avoid depositing of particles on the filter surface and forming a filtration cake. Visualization significantly helps to optimize the cleaning methods, because it brings new overall view on the filtration process in time. The optical method, described in the article, enables to see flow behaviour in a thin laser sheet on the inlet side of a tested filter during the cleaning process. Visualization is a strong tool for investigation of the processes on filters in details and it is also possible to determine concentration of particles after an image analysis. The impact of air flow rate, inverse pressure drop and duration on the cleaning mechanism is investigated in the article. Images of the cleaning process are compared to the hydrodynamic data. The tests are carried out on a pilot filtration setup for waste water treatment.

PATHFINDER ATOMIC POWER PLANT. FILTRATION OF ALUMINUM CORROSION PRODUCTS PRODUCED IN HIGH-TEMPERATURE, HIGH PURITY WATER SYSTEMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Noble, J.H.; Davie, R.L.

1961-05-01

Filter tests were conducted to determine the most suitable filter for removing large quantities of aluminum corrosion product (boehmite) from reactor water. Filters tested included the following: wire-wound, sintered filter elements, sintered ceramic fllter elements, cotton stringwound filter elements, felted-cotton filter elements, cation resin, adsorption resin, diatomaceous earth precoat filter, and a wood-cellulose precoat filter. Parameters measured were flow rate, filter-influent and -effluent boehmite concentration, pressure drop, and final filter load. The pressure drop and efficiency of the filters was correlated with boehmite load. Boehmite deposits on filters as a nonporous gelatinous cake, and causes a rapidly increasing pressure drop.more » Tests indicate that the optimum load with filter elements and precoat filters is achieved at a pressure drop of 25 psi. Very little additional load can be obtained by operating to a higher pressure drop. Of the filters tested, the precoat filter snd 40 to 60 mesh cation resin were the more effective in removing boehmite. The efficiency of the precoat filter was in excess of 99%, and the efficiency of the cation resin was for the most part in excess of 95%. For various reasons, the other filters were eliminated from final consideration. The test program and available literature indicated that an element type precoat filter using wood cellulose as the precoat media would be most suitable for the proposed application. (auth)« less

Exmouth Gulf, Australia as seen from STS-67 Endeavour

NASA Image and Video Library

1995-03-17

The Exmouth Gulf, western Australia, is bounded on the west by the Cape Ranges; near the base of the peninsula the Learmonth Airfield, site of a solar observatory, can be seen. Spit-accretion ridges formed on ancient beaches extend along the western edge of the peninsula, which today is lined by the Ningaloo Reef. Red mud carried by floodwaters, the result of Hurricane Bobby the previous week, cover flat coastal land along the eastern side of the gulf. The mud is mixing slowly with marine water as it filters through passes between mangrove-covered islands. A filamentous pattern in the gulf probably indicates a plankton bloom. Island paleodunes stretching from south to north cover the landscape.

Airborne molds and mycotoxins associated with handling of corn silage and oilseed cakes in agricultural environment

NASA Astrophysics Data System (ADS)

Lanier, Caroline; Richard, Estelle; Heutte, Natacha; Picquet, Rachel; Bouchart, Valérie; Garon, David

2010-05-01

In agricultural areas, the contamination of feedstuffs with molds and mycotoxins presents major environmental and health concerns. During cattle feeding, fungi and mycotoxins were monitored in corn silage, oilseed cakes and bioaerosols collected in Normandy. Most of the corn silages were found to be contaminated by deoxynivalenol (mean concentration: 1883 μg kg -1) while a few of oilseed cakes were contaminated by alternariol, fumonisin B 1 or gliotoxin. In ambient bioaerosols, the values for fungi per cubic meter of air varied from 4.3 × 10 2 to 6.2 × 10 5 cfu m -3. Seasonal variations were observed with some species like Aspergillus fumigatus which significantly decreased between the 2 seasons ( P = 0.0186) while the Penicillium roqueforti group significantly increased during the second season ( P = 0.0156). In the personal bioaerosols, the values for fungi per cubic meter of air varied from 3.3 10 3 to 1.7 10 6 cfu m -3 and the number of A. fumigatus spores significantly decreased between the 2 seasons ( P = 0.0488). Gliotoxin, an immunosuppressive mycotoxin, was quantified in 3 personal filters at 3.73 μg m -3, 1.09 μg m -3 and 2.97 μg m -3.

Enrichment of sulfate reducing anaerobic methane oxidizing community dominated by ANME-1 from Ginsburg Mud Volcano (Gulf of Cadiz) sediment in a biotrickling filter.

PubMed

Bhattarai, Susma; Cassarini, Chiara; Rene, Eldon R; Zhang, Yu; Esposito, Giovanni; Lens, Piet N L

2018-07-01

This study was performed to enrich anaerobic methane-oxidizing archaea (ANME) present in sediment from the Ginsburg Mud Volcano (Gulf of Cadiz) in a polyurethane foam packed biotrickling filter (BTF). The BTF was operated at 20 (±2) °C, ambient pressure with continuous supply of methane for 248 days. Sulfate reduction with simultaneous sulfide production (accumulating ∼7 mM) after 200 days of BTF operation evidenced anaerobic oxidation of methane (AOM) coupled to sulfate reduction. High-throughput sequence analysis of 16S rRNA genes showed that after 248 days of BTF operation, the ANME clades enriched to more than 50% of the archaeal sequences, including ANME-1b (40.3%) and ANME-2 (10.0%). Enrichment of the AOM community was beneficial to Desulfobacteraceae, which increased from 0.2% to 1.8%. Both the inoculum and the BTF enrichment contained large populations of anaerobic sulfur oxidizing bacteria, suggesting extensive sulfur cycling in the BTF. Copyright © 2018 Elsevier Ltd. All rights reserved.

Development of environmental friendly lost circulation material from banana peel

NASA Astrophysics Data System (ADS)

Sauki, Arina; Hasan, Nur â.€˜Izzati; Naimi, Fardelen Binti Md; Othman, Nur Hidayati

2017-12-01

Loss of expensive mud could lead to major financial problem in executing a drilling project and is one of the biggest problems that need to be tackled during drilling. Synthetic Based Mud (SBM) is the most stable state of the art drilling mud used in current drilling technologies. However, the problem with lost circulation is still inevitable. The focus of this project is to develop a new potential waste material from banana peel in order to combat lost circulation in SBM. Standard industrial Lost Circulation Material (LCM) is used to compare the performance of banana peel as LCM in SBM. The effects of different sizing of banana peels (600 micron, 300 micron and 100 micron) were studied on the rheological and filtration properties of SBM and the bridging performance of banana peel as LCM additive. The tests were conducted using viscometer, HTHP filter press and sand bed tester. Thermal analysis of banana peel was also studied using TGA. According to the results obtained, 300 and 100 micron size of banana peel LCM exhibited an improved bridging performance by 65% as compared to industrial LCM. However, banana peel LCM with the size of 600 micron failed to act as LCM due to the total invasion of mud into the sand bed.

Influence of process operating parameters on dryness level and energy saving during wastewater sludge electro-dewatering.

PubMed

Mahmoud, Akrama; Hoadley, Andrew F A; Conrardy, Jean-Baptiste; Olivier, Jérémy; Vaxelaire, Jean

2016-10-15

Electrically assisted mechanical dewatering, known as electro-dewatering (EDW), is an alternative emerging technology for energy-efficient liquid/solids separation in the dewatering of wastewater sludge. In this study, the performance of the electro-dewatering (EDW) process for activated wastewater sludge was investigated. The influence of the operating modes; being the timing of voltage (U-EDW) or current (I-EDW) application to either or both the filtration and compression stages, and the influence of the applied pressure (in successive 30 min pressure steps) were studied. The results showed that by delaying the application of the electric field to the filter cake compression stage, there was a potential saving in power consumption of around 10-12% in the case of U-EDW and about 30-46% in the case of I-EDW. The increase of the applied pressure from 0.5 to 12 bar during the filter cake compression stage leads to an increase in electro-dewatering kinetics. The results also reveal that at a low electric field level the increase of the processing pressure has a relatively pronounced effect on the dewatering process. At high levels of the electric field, a minimum processing pressure (4-6 bar) is required to improve the electrical contact between the electrode and the sludge and thus lower the energy consumption. Copyright © 2016 Elsevier Ltd. All rights reserved.

Soy Protein Isolate As Fluid Loss Additive in Bentonite-Water-Based Drilling Fluids.

PubMed

Li, Mei-Chun; Wu, Qinglin; Song, Kunlin; Lee, Sunyoung; Jin, Chunde; Ren, Suxia; Lei, Tingzhou

2015-11-11

Wellbore instability and formation collapse caused by lost circulation are vital issues during well excavation in the oil industry. This study reports the novel utilization of soy protein isolate (SPI) as fluid loss additive in bentonite-water based drilling fluids (BT-WDFs) and describes how its particle size and concentration influence on the filtration property of SPI/BT-WDFs. It was found that high pressure homogenization (HPH)-treated SPI had superior filtration property over that of native SPI due to the improved ability for the plugging pore throat. HPH treatment also caused a significant change in the surface characteristic of SPI, leading to a considerable surface interaction with BT in aqueous solution. The concentration of SPI had a significant impact on the dispersion state of SPI/BT mixtures in aquesous solution. At low SPI concentrations, strong aggregations were created, resulting in the formation of thick, loose, high-porosity and high-permeability filter cakes and high fluid loss. At high SPI concentrations, intercatlated/exfoliated structures were generated, resulting in the formation of thin, compact, low-porosity and low-permeability filter cakes and low fluid loss. The SPI/BT-WDFs exhibited superior filtration property than pure BT-WDFs at the same solid concentraion, demonstrating the potential utilization of SPI as an effective, renewable, and biodegradable fluid loss reducer in well excavation applications.

Geopolymerisation of silt generated from construction and demolition waste washing plants.

PubMed

Lampris, C; Lupo, R; Cheeseman, C R

2009-01-01

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (<63mum) silt particles that is classified as inert waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.

Numerical simulation of two-phase filtration in the near well bore zone

NASA Astrophysics Data System (ADS)

Maksat, Kalimoldayev; Kalipa, Kuspanova; Kulyash, Baisalbayeva; Orken, Mamyrbayev; Assel, Abdildayeva

2018-04-01

On the basis of the fundamental laws of energy conservation, nonstationary processes of filtration of two-phase liquids in multilayered reservoirs in the near well bore zone are considered. Number of reservoirs, fluid pressure in the given reservoirs, reservoir permeability, oil viscosity, etc. are taken into account upon that. Plane-parallel flow and axisymmetric cases have been studied. In the numerical solution, non-structured meshes are used. Closer to the well, the meshes thicken. The integration step over time is defined by the generalized Courant inequality. As a result, there are no large oscillations in the numerical solutions obtained. Oil production rates, Poisson's ratios, D-diameters of the well, filter height, filter permeability, and cumulative thickness of the filter cake and the area have been taken as the main inputs in numerical simulation of non-stationary processes of two-phase filtration.

Comparative performance of sugarcane bagasse and black polyethylene as mulch for squash (Cucurbita pepo L.) production

USDA-ARS?s Scientific Manuscript database

Louisiana processed 11.6 million mt of sugarcane in 2014, producing 1.36 million mt of raw sugar and an estimated 3.5 million mt of bagasse. Sugarcane bagasse is the fibrous material remaining after removing the sucrose, water, and other impurities (filter mud) from the millable sugarcane. Typically...

Treating exhaust gas from a pressurized fluidized bed reaction system

DOEpatents

Isaksson, J.; Koskinen, J.

1995-08-22

Hot gases from a pressurized fluidized bed reactor system are purified. Under super atmospheric pressure conditions hot exhaust gases are passed through a particle separator, forming a filtrate cake on the surface of the separator, and a reducing agent--such as an NO{sub x} reducing agent (like ammonia)--is introduced into the exhaust gases just prior to or just after particle separation. The retention time of the introduced reducing agent is enhanced by providing a low gas velocity (e.g. about 1--20 cm/s) during passage of the gas through the filtrate cake while at super atmospheric pressure. Separation takes place within a distinct pressure vessel, the interior of which is at a pressure of about 2--100 bar, and introduction of reducing agent can take place at multiple locations (one associated with each filter element in the pressure vessel), or at one or more locations just prior to passage of clean gas out of the pressure vessel (typically passed to a turbine). 8 figs.

Treating exhaust gas from a pressurized fluidized bed reaction system

DOEpatents

Isaksson, Juhani; Koskinen, Jari

1995-01-01

Hot gases from a pressurized fluidized bed reactor system are purified. Under superatmospheric pressure conditions hot exhaust gases are passed through a particle separator, forming a flitrate cake on the surface of the separator, and a reducing agent--such as an NO.sub.x reducing agent (like ammonia), is introduced into the exhaust gases just prior to or just after particle separation. The retention time of the introduced reducing agent is enhanced by providing a low gas velocity (e.g. about 1-20 cm/s) during passage of the gas through the filtrate cake while at superatmospheric pressure. Separation takes place within a distinct pressure vessel the interior of which is at a pressure of about 2-100 bar, and-introduction of reducing agent can take place at multiple locations (one associated with each filter element in the pressure vessel), or at one or more locations just prior to passage of clean gas out of the pressure vessel (typically passed to a turbine).

Fuel Efficient Diesel Particulate Filter (DPF) Modeling and Development

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stewart, Mark L.; Gallant, Thomas R.; Kim, Do Heui

The project described in this report seeks to promote effective diesel particulate filter technology with minimum fuel penalty by enhancing fundamental understanding of filtration mechanisms through targeted experiments and computer simulations. The overall backpressure of a filtration system depends upon complex interactions of particulate matter and ash with the microscopic pores in filter media. Better characterization of these phenomena is essential for exhaust system optimization. The acicular mullite (ACM) diesel particulate filter substrate is under continuing development by Dow Automotive. ACM is made up of long mullite crystals which intersect to form filter wall framework and protrude from the wallmore » surface into the DPF channels. ACM filters have been demonstrated to effectively remove diesel exhaust particles while maintaining relatively low backpressure. Modeling approaches developed for more conventional ceramic filter materials, such as silicon carbide and cordierite, have been difficult to apply to ACM because of properties arising from its unique microstructure. Penetration of soot into the high-porosity region of projecting crystal structures leads to a somewhat extended depth filtration mode, but with less dramatic increases in pressure drop than are normally observed during depth filtration in cordierite or silicon carbide filters. Another consequence is greater contact between the soot and solid surfaces, which may enhance the action of some catalyst coatings in filter regeneration. The projecting crystals appear to provide a two-fold benefit for maintaining low backpressures during filter loading: they help prevent soot from being forced into the throats of pores in the lower porosity region of the filter wall, and they also tend to support the forming filter cake, resulting in lower average cake density and higher permeability. Other simulations suggest that soot deposits may also tend to form at the tips of projecting crystals due to the axial velocity component of exhaust moving down the filter inlet channel. Soot mass collected in this way would have a smaller impact on backpressure than soot forced into the flow restrictions deeper in the porous wall structure. This project has focused on the development of computational, analytical, and experimental techniques that are generally applicable to a wide variety of exhaust aftertreatment technologies. By helping to develop improved fundamental understanding pore-scale phenomena affecting filtration, soot oxidation, and NOX abatement, this cooperative research and development agreement (CRADA) has also assisted Dow Automotive in continuing development and commercialization of the ACM filter substrate. Over the course of this research project, ACM filters were successfully deployed on the Audi R10 TDI racecar which won the 24 Hours of LeMans endurance race in 2006, 2007, and 2008; and the 12 Hours of Sebring endurance race in 2006 and 2007. It would not have been possible for the R10 to compete in these traditionally gasoline-dominated events without reliable and effective exhaust particulate filtration. These successes demonstrated not only the performance of automotive diesel engines, but the efficacy of DPF technology as it was being deployed around the world to meet new emissions standards on consumer vehicles. During the course of this CRADA project, Dow Automotive commercialized their ACM DPF technology under the AERIFYTM DPF brand.« less

Contactor/filter improvements

DOEpatents

Stelman, David

1989-01-01

A contactor/filter arrangement for removing particulate contaminants from a gaseous stream includes a housing having a substantially vertically oriented granular material retention member with upstream and downstream faces, a substantially vertically oriented microporous gas filter element, wherein the retention member and the filter element are spaced apart to provide a zone for the passage of granular material therethrough. The housing further includes a gas inlet means, a gas outlet means, and means for moving a body of granular material through the zone. A gaseous stream containing particulate contaminants passes through the gas inlet means as well as through the upstream face of the granular material retention member, passing through the retention member, the body of granular material, the microporous gas filter element, exiting out of the gas outlet means. Disposed on the upstream face of the filter element is a cover screen which isolates the filter element from contact with the moving granular bed and collects a portion of the particulates so as to form a dust cake having openings small enough to exclude the granular material, yet large enough to receive the dust particles. In one embodiment, the granular material is comprised of prous alumina impregnated with CuO, with the cover screen cleaned by the action of the moving granular material as well as by backflow pressure pulses.

Micron-pore-sized metallic filter tube membranes for filtration of particulates and water purification.

PubMed

Phelps, T J; Palumbo, A V; Bischoff, B L; Miller, C J; Fagan, L A; McNeilly, M S; Judkins, R R

2008-07-01

Robust filtering techniques capable of efficiently removing particulates and biological agents from water or air suffer from plugging, poor rejuvenation, low permeance, and high backpressure. Operational characteristics of pressure-driven separations are in part controlled by the membrane pore size, charge of particulates, transmembrane pressure and the requirement for sufficient water flux to overcome fouling. With long term use filters decline in permeance due to filter-cake plugging of pores, fouling, or filter deterioration. Though metallic filter tube development at ORNL has focused almost exclusively on gas separations, a small study examined the applicability of these membranes for tangential filtering of aqueous suspensions of bacterial-sized particles. A mixture of fluorescent polystyrene microspheres ranging in size from 0.5 to 6 microm in diameter simulated microorganisms in filtration studies. Compared to a commercial filter, the ORNL 0.6 microm filter averaged approximately 10-fold greater filtration efficiency of the small particles, several-fold greater permeance after considerable use and it returned to approximately 85% of the initial flow upon backflushing versus 30% for the commercial filter. After filtering several liters of the particle-containing suspension, the ORNL composite filter still exhibited greater than 50% of its initial permeance while the commercial filter had decreased to less than 20%. When considering a greater filtration efficiency, greater permeance per unit mass, greater percentage of rejuvenation upon backflushing (up to 3-fold), and likely greater performance with extended use, the ORNL 0.6 microm filters can potentially outperform the commercial filter by factors of 100-1,000 fold.

Drilling fluid containing a copolymer filtration control agent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Enright, D.P.; Lucas, J.M.; Perricone, A.C.

1981-10-06

The invention relates to an aqueous drilling fluid composition, a filtration control agent for utilization in said aqueous drilling fluid, and a method of forming a filter cake on the wall of a well for the reduction of filtrate from said drilling fluid, by utilization of a copolymer of: (1) a (Meth) acrylamido alkyl sulfonic acid or alkali metal salt thereof; and (2) a (Meth) acrylamide or n-alkyl (Meth) acrylamide. The copolymer may be cross-linked with a quaternary ammonium salt cross-linking agent.

Drilling fluid containing a copolymer filtration control agent

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lucas, J. M.

1985-10-15

The invention relates to an aqueous drilling fluid composition, a filtration control agent for utilization in said aqueous drilling fluid, and a method of forming a filter cake on the wall of a well for the reduction of filtrate from said drilling fluid, by utilization of a copolymer of: a (meth) acrylamido alkyl sulfonic acid or alkali metal salt thereof; and N, N-dialkyl (meth) acrylamide. The copolymer may be cross-linked with N,N'-methylenebisacrylamide or other appropriate cross-linking agent.

Innovative site remediation technology: Thermal desorption. Volume 6

DOE Office of Scientific and Technical Information (OSTI.GOV)

Anderson, W.C.

1993-11-01

The monograph on thermal desorption is one of a series of eight on innovative site and waste remediation technologies that are the culmination of a multiorganization effort involving more than 100 experts over a two-year period. The thermal desorption processes addressed in this monograph use heat, either direct or indirect, ex situ, as the principal means to physically separate and transfer contaminants from soils, sediments, sludges, filter cakes, or other media. Thermal desorption is part of a treatment train; some pre- and postprocessing is necessary.

A comparative study on the decomposition of edible and non-edible oil cakes in the Gangetic alluvial soil of West Bengal.

PubMed

Mondal, Sudeshna; Das, Ritwika; Das, Amal Chandra

2014-08-01

An experiment has been conducted under laboratory conditions to investigate the effect of decomposition of two edible oil cakes, viz. mustard cake (Brassica juncea L) and groundnut cake (Arachis hypogaea L), and two non-edible oil cakes, viz. mahua cake (Madhuca indica Gmel) and neem cake (Azadirachta indica Juss), at the rate of 5.0 t ha(-1) on the changes of microbial growth and activities in relation to transformations and availability of some plant nutrients in the Gangetic alluvial (Typic Haplustept) soil of West Bengal, India. Incorporation of oil cakes, in general, highly induced the proliferation of total bacteria, actinomycetes, and fungi, resulting in greater retention and availability of oxidizable C, N, and P in soil. As compared to untreated control, the highest stimulation of total bacteria and actinomycetes was recorded with mustard cake (111.9 and 84.3 %, respectively) followed by groundnut cake (50.5 and 52.4 %, respectively), while the fungal colonies were highly accentuated due to the incorporation of neem cake (102.8 %) in soil. The retention of oxidizable organic C was highly increased due to decomposition of non-edible oil cakes, more so under mahua cake (14.5 %), whereas edible oil cakes and groundnut cake in particular exerted maximum stimulation (16.7 %) towards the retention of total N in soil. A similar trend was recorded towards the accumulation of available mineral N in soil and this was more pronounced with mustard cake (45.6 %) for exchangeable NH4 (+) and with groundnut cake (63.9 %) for soluble NO3 (-). The highest retention of total P (46.9 %) was manifested by the soil when it was incorporated with neem cake followed by the edible oil cakes; while the available P was highly induced due to the addition of edible oil cakes, the highest being under groundnut cake (23.5 %) followed by mustard cake (19.6 %).

Draft Genome Sequence of the Cellulolytic Bacterium Clostridium papyrosolvens C7 (ATCC 700395).

PubMed

Zepeda, Veronica; Dassa, Bareket; Borovok, Ilya; Lamed, Raphael; Bayer, Edward A; Cate, Jamie H D

2013-09-12

We report the draft genome sequence of the cellulose-degrading bacterium Clostridium papyrosolvens C7, originally isolated from mud collected below a freshwater pond in Massachusetts. This Gram-positive bacterium grows in a mesophilic anaerobic environment with filter paper as the only carbon source, and it has a simple cellulosome system with multiple carbohydrate-degrading enzymes.

Draft Genome Sequence of the Cellulolytic Bacterium Clostridium papyrosolvens C7 (ATCC 700395)

PubMed Central

Zepeda, Veronica; Dassa, Bareket; Borovok, Ilya; Lamed, Raphael; Bayer, Edward A.

2013-01-01

We report the draft genome sequence of the cellulose-degrading bacterium Clostridium papyrosolvens C7, originally isolated from mud collected below a freshwater pond in Massachusetts. This Gram-positive bacterium grows in a mesophilic anaerobic environment with filter paper as the only carbon source, and it has a simple cellulosome system with multiple carbohydrate-degrading enzymes. PMID:24029755

Effects of addition of different fibers on rheological characteristics of cake batter and quality of cakes.

PubMed

Aydogdu, Ayca; Sumnu, Gulum; Sahin, Serpil

2018-02-01

The aim of this study was to investigate the effects of addition of dietary fibers on rheological properties of batter and cake quality. Wheat flour was replaced by 5 and 10% (wt%) oat, pea, apple and lemon fibers. All cake batters showed shear thinning behavior. Incorporation of fibers increased consistency index (k), storage modulus (G') and loss modulus (G″). As quality parameters, specific volume, hardness, weight loss, color and microstructure of cakes were investigated. Cakes containing oat and pea fibers (5%) had similar specific volume and texture with control cakes which contained no fiber. As fiber concentration increased, specific volume decreased but hardness increased. No significant difference was found between weight loss of control cake and cakes with oat, pea and apple fibers. Lemon fiber enriched cakes had the lowest specific volume, weight loss and color difference. When microstructural images were examined, it was seen that control cake had more porous structure than fiber enriched cakes. In addition, lemon and apple fiber containing cakes had less porous crumb structure as compared to oat and pea containing ones. Oat and pea fiber (5%) enriched cakes had similar physical properties (volume, texture and color) with control cakes.

Internal Structure and Morphology Profile in Optimizing Filter Membrane Performance

NASA Astrophysics Data System (ADS)

Sanaei, Pejman; Cummings, Linda J.

Membrane filters are in widespread use, and manufacturers have considerable interest in improving their performance, in terms of particle retention properties, and total throughput over the filter lifetime. A good question to ask is therefore: what is the optimal configuration of filter membranes, in terms of internal morphology (pore size and shape), to achieve the most efficient filtration? To answer this question, we must first propose a robust measure of filtration performance. As filtration occurs the membrane becomes blocked, or fouled, by the impurities in the feed solution, and any performance measure must take account of this. For example, one performance measure might be the total throughput (the volume of filtered feed solution) at the end of the filtration process, when the membrane is so badly blocked that it is deemed no longer functional. Here we present a simplified mathematical model, which (i) characterizes membrane internal pore structure via pore or permeability profiles in the depth of the membrane; (ii) accounts for various membrane fouling mechanisms (adsorption, blocking and cake formation); and (iv) predicts the optimum pore profile for our chosen performance measure. NSF DMS-1261596 and NSF DMS-1615719.

Special diatomite solves fiberglass particles filtration problem

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-07-01

Johns-Manville Corp. has developed a water treatment system which is based on the principle of zero-discharge of process water and which uses an alum-coated Celite diatomaceous earth filter for removing particles of carbon black and abrasive glass, tramp dirt, and oils and grease out of waste water from its fiberglass plants at Parkersburg, W. Va., and elsewhere. The resulting water is essentially free of suspended solids larger than 0.5j at Vertical Bar3; 5 mg/l. concentration, even when the solids concentration in the filter feed water ranges from 50 to 1000 mg/l. The system's core is the alum coating, which ismore » obtained by reacting the diatomite with aluminum sulfate and soda ash. Because it has a highly positive electrical charge, the coating attracts the negatively charged carbon particles and attaches them to the diatomite surface to be filtered out. Filtration cycles vary from 8 to 24 hr depending on the raw water and filter grade used; the terminal pressure is about 60 psig. At cycles' end, the filter cake is up to 2.5 in. thick; this is disposed of in sanitary landfills.« less

Use of baru (Brazilian almond) waste from physical extraction of oil to produce gluten free cakes.

PubMed

Pineli, Lívia de Lacerda de Oliveira; de Aguiar, Lorena Andrade; de Oliveira, Guilherme Theodoro; Botelho, Raquel Braz Assunção; Ibiapina, Maria do Desterro Ferreira Pereira; de Lima, Herbert Cavalcanti; Costa, Ana Maria

2015-03-01

The extraction of oil from baru almonds produces a waste that carries part of their nutritional qualities and antioxidants. It can be used to produce partially deffated baru flour (PDBF). We aimed to evaluate the applicability of PDBF and the effect of the addition of xanthan gum (XG) to produce gluten free cakes. Cakes were prepared with 100% wheat flour (WF cake) and with 100% PDBF and four different levels of XG (0%-PDBF cake, 0.1%-X1, 0.2%-X2 and 0.3%-X3 cakes), and evaluated for composition, antioxidants, moisture, specific volume, texture and sensory acceptance. PDBF cakes showed lower carbohydrate values, but higher protein, lipids, calories and antioxidant contents. They were rich in fiber, as well as iron, zinc and copper. The replacement of WF by PDBF resulted in an increased hardness and adhesiveness and a decreased cohesiveness, elasticity and moisture. Chewiness of X2 cake was similar to that of WF cake. X2 and X3 cakes showed specific volume closer to that of WF cake. No difference was found among the treatments for texture and appearance acceptances. Flavor of X2 and X3 cakes were more accepted than WF cake. Acceptance of all cakes were in the liking region of hedonic scale. PBDF associated to XG is a feasible option to substitute WF in gluten free cake, improving its nutritional quality.

Removal of Inclusions from Molten Aluminum by Supergravity Filtration

NASA Astrophysics Data System (ADS)

Song, Gaoyang; Song, Bo; Yang, Zhanbing; Yang, Yuhou; Zhang, Jing

2016-12-01

A new approach to removing inclusions from aluminum melt by supergravity filtration was investigated. The molten aluminum containing MgAl2O4 spinel and coarse Al3Ti particles was isothermally filtered with different gravity coefficients, different filtering times, and various filtering temperatures under supergravity field. When the gravity coefficient G ≥ 50, the alloy samples were divided automatically into two parts: the upper residue and the lower filtered aluminum. All inclusions (MgAl2O4 and Al3Ti particles) were nearly intercepted in the upper residue by filter felt with average pore size of 44.78 μm. The removal efficiencies of oxide inclusions and Al3Ti particles exceeded 98 and 90 pct, respectively, at G ≥ 50, t = 2 minutes, T = 973 K (700 °C). Besides, the yield of purified aluminum was up to 92.1 pct at G = 600, t = 2 minutes, and T = 973 K (700 °C). The calculations of centrifugal pressure indicated that supergravity filtration could effectively overcome the pressure drop without meeting the rigorous requirement of height of molten metal, especially for using the fine-pore filter medium. Moreover, cake-mode filtration was the major mechanism of supergravity filtration of molten metal in this work.

Separation of nanoparticles: Filtration and scavenging from waste incineration plants.

PubMed

Förster, Henning; Thajudeen, Thaseem; Funk, Christine; Peukert, Wolfgang

2016-06-01

Increased amounts of nanoparticles are applied in products of everyday life and despite material recycling efforts, at the end of their life cycle they are fed into waste incineration plants. This raises the question on the fate of nanoparticles during incineration. In terms of environmental impact the key question is how well airborne nanoparticles are removed by separation processes on their way to the bag house filters and by the existing filtration process based on pulse-jet cleanable fibrous filter media. Therefore, we investigate the scavenging and the filtration of metal nanoparticles under typical conditions in waste incineration plants. The scavenging process is investigated by a population balance model while the nanoparticle filtration experiments are realized in a filter test rig. The results show that depending on the particle sizes, in some cases nearly 80% of the nanoparticles are scavenged by fly ash particles before they reach the bag house filter. For the filtration step dust cakes with a pressure drop of 500Pa or higher are found to be very effective in preventing nanoparticles from penetrating through the filter. Thus, regeneration of the filter must be undertaken with care in order to guarantee highly efficient collection of particles even in the lower nanometre size regime. Copyright © 2016 Elsevier Ltd. All rights reserved.

Installation Restoration Program Phase 1 - Records Search, O’Hare Air Reserve Forces Facility, Illinois

DTIC Science & Technology

1983-12-01

clarifiers, activated sludge units, trickling filters, aerobic and anaerobic digesters, and various dowatering devices and recommendations for...for locations of water- bearing fractures. Additional responsibilities included drilling with mud and air rotary drilling rigs as well as bucket auger...interpretation. Also conducted earth resistivity surveys in Georgia and Alabama Piedmont Provinces for locations of water- bearing fractures. Additional

Impact of sugarcane bagasse ash as an amendment on the physical properties, nutrient content and seedling growth of a certified organic greenhouse growing media

USDA-ARS?s Scientific Manuscript database

Sugarcane bagasse is the fibrous material remaining after removing the sucrose, water, and other impurities (filter mud) from the milable sugarcane. Louisiana sugarcane mills use a portion of the sugarcane bagasse to produce steam power to run equipment within the mill and/or as a boiler fuel for th...

Navy Bean Flour Particle Size and Protein Content Affect Cake Baking and Batter Quality(1).

PubMed

Singh, Mukti; Byars, Jeffrey A; Liu, Sean X

2015-06-01

Whole navy bean flour and its fine and coarse particle size fractions were used to completely replace wheat flour in cakes. Replacement of wheat flour with whole bean flour significantly increased the protein content. The protein content was adjusted to 3 levels with navy bean starch. The effect of navy bean flour and its fractions at 3 levels of protein on cake batter rheology and cake quality was studied and compared with wheat flour samples. Batters prepared from navy bean flour and its fractions had higher viscosity than the cake flour. Reducing the protein content by addition of starch significantly lowered the viscosity of cake batters. The whole navy bean flour and coarse bean fraction cakes were softer than cakes made with wheat flour but had reduced springiness. Principal component analysis showed a clear discrimination of cakes according to protein. It also showed that low protein navy bean flour cakes were similar to wheat flour cakes. Navy bean flour with protein content adjusted to the level of cake (wheat) flour has potential as a healthy alternative in gluten-free cakes. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

From baking a cake to solving the diffusion equation

NASA Astrophysics Data System (ADS)

Olszewski, Edward A.

2006-06-01

We explain how modifying a cake recipe by changing either the dimensions of the cake or the amount of cake batter alters the baking time. We restrict our consideration to the génoise and obtain a semiempirical relation for the baking time as a function of oven temperature, initial temperature of the cake batter, and dimensions of the unbaked cake. The relation, which is based on the diffusion equation, has three parameters whose values are estimated from data obtained by baking cakes in cylindrical pans of various diameters. The relation takes into account the evaporation of moisture at the top surface of the cake, which is the dominant factor affecting the baking time of a cake.

DEVELOPMENT OF DEWATERING AIDS FOR MINERALS AND COAL FINES

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roe-Hoam Yoon; Ramazan Asmatulu; Ismail Yildirim

2004-07-01

MCT has developed a suite of novel dewatering chemicals (or aids) that are designed to cause a decrease in the capillary pressures of the water trapped in a filter cake by (1) decreasing the surface tension of water, (2) increasing the contact angles of the particles to be dewatered, and (3) causing the particles to coagulate, all at the same time. The decrease in capillary pressure in turn causes an increase in the rate filtration, an increase in throughput, and a decrease in pressure drop requirement for filtration. The reagents are used frequently as blends of different chemicals in ordermore » to bring about the changes in all of the process variables noted above. The minerals and coal samples tested in the present work included copper sulfide, lead sulfide, zinc sulfide, kaolin clay, talc, and silica. The laboratory-scale test work included studies of reagent types, drying cycle times, cake thickness, slurry temperature, conditioning intensity and time, solid content, and reagent dosages. To better understand the mechanisms involved, fundamental studies were also conducted. These included the measurements of the contact angles of the particles to be dewatered (which are the measures of particle hydrophobicity) and the surface tensions of the filtrates produced from dewatering tests. The results of the laboratory-scale filtration experiments showed that the use of the novel dewatering aids can reduce the moistures of the filter cake by 30 to 50% over what can be achieved using no dewatering aids. In many cases, such high levels of moisture reductions are sufficient to obviate the needs for thermal drying, which is costly and energy intensive. Furthermore, the use of the novel dewatering aids cause a substantial increase in the kinetics of dewatering, which in turn results in increased throughput. As a result of these technological advantages, the novel dewatering aids have been licensed to Nalco, which is one of the largest mining chemicals companies of the world. At least one mineral company is currently using the technology in full-scale plant operation, which has resulted in the shutdown of a thermal dryer.« less

Relative importance of moisture migration and amylopectin retrogradation for pound cake crumb firming.

PubMed

Luyts, A; Wilderjans, E; Van Haesendonck, I; Brijs, K; Courtin, C M; Delcour, J A

2013-12-15

Moisture migration largely impacts cake crumb firmness during storage at ambient temperature. To study the importance of phenomena other than crumb to crust moisture migration and to exclude moisture and temperature gradients during baking, crustless cakes were baked using an electrical resistance oven (ERO). Cake crumb firming was evaluated by texture analysis. First, ERO cakes with properties similar to those baked conventionally were produced. Cake batter moisture content (MC) was adjusted to ensure complete starch gelatinisation in the baking process. In cakes baked conventionally, most of the increase in crumb firmness during storage was caused by moisture migration. Proton nuclear magnetic resonance ((1)H NMR) showed that the population containing protons of crystalline starch grew during cake storage. These and differential scanning calorimetry (DSC) data pointed to only limited amylopectin retrogradation. The limited increase in amylopectin retrogradation during cake storage cannot solely account for the significant firming of ERO cakes and, hence, other phenomena are involved in cake firming. Copyright © 2013 Elsevier Ltd. All rights reserved.

New insights into comparison between synthetic and practical municipal wastewater in cake layer characteristic analysis of membrane bioreactor.

PubMed

Zhou, Lijie; Zhuang, Wei-Qin; Wang, Xin; Yu, Ke; Yang, Shufang; Xia, Siqing

2017-11-01

In previous studies, cake layer analysis in membrane bioreactor (MBR) was both carried out with synthetic and practical municipal wastewater (SMW and PMW), leading to different results. This study aimed to identify the comparison between SMW and PMW in cake layer characteristic analysis of MBR. Two laboratory-scale anoxic/oxic MBRs were operated for over 90days with SMW and PMW, respectively. Results showed that PMW led to rough cake layer surface with particles, and the aggravation of cake layer formation with thinner and denser cake layer. Additionally, inorganic components, especially Si and Al, in PMW accumulated into cake layer and strengthened the cake layer structure, inducing severer biofouling. However, SMW promoted bacterial metabolism during cake layer formation, thus aggravated the accumulation of organic components into cake layer. Therefore, SMW highlighted the organic components in cake layer, but weakened the inorganic functions in practical MBR operation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Analgesic Effects of Toad Cake and Toad-cake-containing Herbal Drugs: Analgesic effects of toad cake.

PubMed

Inoue, Eiji; Shimizu, Yasuharu; Masui, Ryo; Usui, Tomomi; Sudoh, Keiichi

2014-03-01

This study was conducted to clarify the analgesic effect of toad cake and toad-cake-containing herbal drugs. We counted the writhing response of mice after the intraperitoneal administration of acetic acid as a nociceptive pain model and the withdrawal response after the plantar surface stimulation of the hind paw induced by partial sciatic nerve ligation of the mice as a neuropathic pain model to investigate the analgesic effect of toad cake and toad-cake-containing herbal drugs. A co-treatment study with serotonin biosynthesis inhibitory drug 4-chloro- DL-phenylalanine methyl ester hydrochloride (PCPA), the catecholamine biosynthesis inhibitory drug α-methyl- DL-tyrosine methyl ester hydrochloride (AMPT) or the opioid receptor antagonist naloxone hydrochloride was also conducted. Analgesic effects in a mouse model of nociceptive pain and neuropathic pain were shown by oral administration of toad cake and toad-cake-containing herbal drugs. The effects of toad cake and toad-cake-containing herbal drugs disappeared upon co-treatment with PCPA, but not with AMPT or naloxone in the nociceptive pain model; the analgesic effect of toad-cake-containing herbal drugs also disappeared upon co-treatment with PCPA in the neuropathic pain model. Toad cake and toad-cake-containing herbal drugs have potential for the treatments of nociceptive pain and of neuropathic pain, such as post-herpetic neuralgia, trigeminal neuralgia, diabetic neuralgia, and postoperative or posttraumatic pain, by activation of the central serotonin nervous system.

[Design and application of a cake-shaping apparatus for drug-separated moxibustion].

PubMed

Zhu, Ai-Jun; Lu, Xiao-Dong

2008-08-01

Acupuncturist makes herbal cakes with traditional manual way, with such disadvantages as slow in making, varying in thickness and size of the cake. When the patients are treated with medical cake-separated moxibustion, they will be unevenly affected by the heat and the patient easily suffers from burning. These hinder clinically wide application of cake-separated moxibustion. With practice of many years, the authors design and make a kind of manual cake-shaping apparatus which can rapidly and conveniently make uniform medical cake, with simple technique, ingenious structure and normal material.

Effect of different flours on quality of legume cakes to be baked in microwave-infrared combination oven and conventional oven.

PubMed

Ozkahraman, Betul Canan; Sumnu, Gulum; Sahin, Serpil

2016-03-01

The objective of this study was to compare the quality of legume cakes baked in microwave-infrared combination (MW-IR) oven with conventional oven. Legume cake formulations were developed by replacing 10 % wheat flour by lentil, chickpea and pea flour. As a control, wheat flour containing cakes were used. Weight loss, specific volume, texture, color, gelatinization degree, macro and micro-structure of cakes were investigated. MW-IR baked cakes had higher specific volume, weight loss and crust color change and lower hardness values than conventionally baked cakes. Larger pores were observed in MW-IR baked cakes according to scanning electron microscope (SEM) images. Pea flour giving the hardest structure, lowest specific volume and gelatinization degree was determined to be the least acceptable legume flour. On the other hand, lentil and chickpea flour containing cakes had the softest structure and highest specific volume showing that lentil and chickpea flour can be used to produce functional cakes.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sievers, David A.; Kuhn, Erik M.; Tucker, Melvin P.

In this study, the reaction conditions used during dilute-acid pretreatment of lignocellulosic biomass control the carbohydrate digestion yield and also hydrolyzate properties. Depending on the conversion route of interest, solid-liquid separation (SLS) may be required to split the hemicellulose-rich liquor from the cellulose-rich insoluble solids, and slurry properties are important for SLS. Corn stover was pretreated at different reaction conditions and the slurries were assessed for conversion yield and filtration performance. Increasing pretreatment temperature reduced the solids mean particle size and resulted in slower slurry filtration rates when vacuum filtered or pressure filtered. Corn stover pretreated at 165 °C formore » 10 min and with 1% H 2SO 4 exhibited the highest xylose yield and best filtration performance with a no-wash filtration rate of 80 kg/h m 2 and cake permeability of 15 x 10 -15.« less

Celebratory Cakes

ERIC Educational Resources Information Center

Mahoney, Ellen

2012-01-01

Cakes are no longer the simple desserts they once were. The cake has evolved into an elaborate, sculptural form that represents a special occasion. Sculptural cake forms have become expressive designs using three-dimensional shapes, an array of surface textures, and a range of colors. The use of cakes in the artwork of David Gilhooly, Wayne…

Comparative study of texture of normal and energy reduced sponge cakes.

PubMed

Baeva, M R; Panchev, I N; Terzieva, V V

2000-08-01

The complete sucrose elimination and its replacement by microencapsulated aspartame (Nutra Sweet) and bulking agents (sorbitol, wheat starch and wheat germ) on the physical and textural sensory characteristics of two diabetic sponge cakes against a control sponge cake was studied. Mathematical and statistical methods were used and regression models worked out, describing the physical and textural characteristics of the three sponge cakes and their values were optimized. The effect on the porosity, springiness, volume and shrinkage of sponge takes was substantial and depended on the amount of the added ingredients. The diabetic sponge cake containing wheat germ showed the least physical and sensory deviations against the control sponge cake. The energy value of the diabetic sponge cakes against the control one was reduced with 25% for the ordinary sponge cake without sucrose and with 29% for sponge cake without sucrose containing wheat germ.

Analgesic Effects of Toad Cake and Toad-cake-containing Herbal Drugs

PubMed Central

Inoue, Eiji; Shimizu, Yasuharu; Masui, Ryo; Usui, Tomomi; Sudoh, Keiichi

2014-01-01

Objectives: This study was conducted to clarify the analgesic effect of toad cake and toad-cake-containing herbal drugs. Methods: We counted the writhing response of mice after the intraperitoneal administration of acetic acid as a nociceptive pain model and the withdrawal response after the plantar surface stimulation of the hind paw induced by partial sciatic nerve ligation of the mice as a neuropathic pain model to investigate the analgesic effect of toad cake and toad-cake-containing herbal drugs. A co-treatment study with serotonin biosynthesis inhibitory drug 4-chloro- DL-phenylalanine methyl ester hydrochloride (PCPA), the catecholamine biosynthesis inhibitory drug α-methyl- DL-tyrosine methyl ester hydrochloride (AMPT) or the opioid receptor antagonist naloxone hydrochloride was also conducted. Results: Analgesic effects in a mouse model of nociceptive pain and neuropathic pain were shown by oral administration of toad cake and toad-cake-containing herbal drugs. The effects of toad cake and toad-cake-containing herbal drugs disappeared upon co-treatment with PCPA, but not with AMPT or naloxone in the nociceptive pain model; the analgesic effect of toad-cake-containing herbal drugs also disappeared upon co-treatment with PCPA in the neuropathic pain model. Conclusion: Toad cake and toad-cake-containing herbal drugs have potential for the treatments of nociceptive pain and of neuropathic pain, such as post-herpetic neuralgia, trigeminal neuralgia, diabetic neuralgia, and postoperative or posttraumatic pain, by activation of the central serotonin nervous system. PMID:25780693

Study of bioleaching under different hydraulic retention time for enhancing the dewaterability of digestate.

PubMed

Li, Linshuai; Gao, Jingqing; Zhu, Songfeng; Li, Yonghong; Zhang, Ruiqin

2015-12-01

Dewatering of kitchen waste digestate is a key problem to solve so as to increase the application of kitchen waste after anaerobic digestion. In this study, the effects of bioleaching under different hydraulic retention time (HRT = 2, 2.5, and 3 days) on dewaterability of kitchen waste digestate were evaluated. A 12-stage plug flow bioreactor with 180 L working volume was used for digestate bioleaching. The bioleached digestate under different HRTs were collected and dewatered by plate-and-frame filter press. The results showed that the moisture contents of digestate cakes were 67.87 % at 2 days of HRT, 58.06 % at 2.5 days of HRT, and 54.45 % at 3 days of HRT, respectively, indicating the longer the HRT, the lower the moisture content of filter cake. Balanced between the cost and practical need, 2.5 days can be used as the HRT in engineering application. Under the condition of HRT of 2.5 days, the pH, specific resistance to filtration (SRF), capillary suction time (CST), and sedimentation rate of digestate changed from the initial values of 8.08, 210.6 s, 23.4 × 10(12) m kg(-1) and 10 % to 3.21, 32.7 s, 2.44 × 10(12) m kg(-1) and 76.8 %, respectively. Based on the observations above, the authors conclude that bioleaching technology is an effective method to enhance digestate dewaterability and reduce the cost of subsequent reutilization.

Elemental composition of airborne dust in the Shale Shaker House during an offshore drilling operation.

PubMed

Hansen, A B; Larsen, E; Hansen, L V; Lyngsaae, M; Kunze, H

1991-12-01

During 2 days of an offshore drilling operation in the North Sea, 16 airborne dust samples from the atmosphere of the Shale Shaker House were collected onto filters. During this operation, drilling mud composed of a water slurry of barite (BaSO4) together with minor amounts of additives, among them chrome lignosulphonate and chrome lignite, was circulated between the borehole and the Shale Shaker House. The concentration of airborne dust in the atmosphere was determined and the elemental composition of the particles analysed by both PIXE (proton-induced X-ray emission) and ICP-MS (inductively coupled plasma-mass spectrometry). The total amount of dust collected varied from 0.04 to 1.41 mg m-3 with barium (Ba) as the single most abundant element. The open shale shakers turned out to be the major cause of generation of dust from the solid components of the drilling mud.

Development of a Pancake-Making Method for a Batter-Based Product

USDA-ARS?s Scientific Manuscript database

Cake and pancake are major batter-based products made with soft wheat flour. A standardized baking method for high-ratio cake has been widely used for evaluating the cake-baking performance of soft wheat flour. Chlorinated flour is used to make high-ratio cake, and the cake formula contains relative...

Influence of different emulsifiers on characteristics of eggless cake containing soy milk: Modeling of physical and sensory properties by mixture experimental design.

PubMed

Rahmati, Nazanin Fatemeh; Mazaheri Tehrani, Mostafa

2014-09-01

Emulsifiers of different structures and functionalities are important ingredients usually used in baking cakes with satisfactory properties. In this study, three emulsifiers including distilled glycerol mono stearate (DGMS), lecithin and sorbitan mono stearate (SMS) were used to bake seven eggless cakes containing soy milk and optimization was performed by using mixture experimental design to produce an eggless cake sample with optimized properties. Physical properties of cake batters (viscosity, specific gravity and stability), cake quality parameters (moisture loss, density, specific volume, volume index, contour, symmetry, color and texture) and sensory attributes of eggless cakes were analyzed to investigate functional potential of the emulsifiers and results were compared with those of control cake containing egg. Almost in all cases emulsifiers, compared to the control cake, changed properties of eggless cakes significantly. Regarding models of different response variables (except for some properties) and their high R(2) (99.51-100), it could be concluded that models obtained by mixture design were significantly fitted for the studied responses.

The membrane separation mechanism in protein concentration from the extract of waste press cake in biofuel manufacturing process of Jatropha seeds

NASA Astrophysics Data System (ADS)

Chung, T. W.; Chen, C. K.; Hsu, S. H.

2017-11-01

Protein concentration process using filter membrane has a significant advantage on energy saving compared to the traditional drying processes. However, fouling on large membrane area and frequent membrane cleaning will increase the energy consumption and operation cost for the protein concentration process with filter membrane. In this study, the membrane filtration for protein concentration will be conducted and compared with the recent protein concentration technology. The analysis of operating factors for protein concentration process using filter membrane was discussed. The separation mechanism of membrane filtration was developed according to the size difference between the pore of membrane and the particle of filter material. The Darcy’s Law was applied to discuss the interaction on flux, TMP (transmembrane pressure) and resistance in this study. The effect of membrane pore size, pH value and TMP on the steady-state flux (Jst) and protein rejection (R) were studied. It is observed that the Jst increases with decreasing membrane pore size, the Jst increases with increasing TMP, and R increased with decreasing solution pH value. Compare to other variables, the pH value is the most significant variable for separation between protein and water.

Determination of selenium at trace levels in geologic materials by energy-dispersive X-ray fluorescence spectrometry

USGS Publications Warehouse

Wahlberg, J.S.

1981-01-01

Low levels of selenium (0.1-500 ppm) in both organic and inorganic geologic materials can be semiquantitatively measured by isolating Se as a thin film for presentation to an energy-dispersive X-ray fluorescence spectrometer. Suitably pulverized samples are first digested by fusing with a mixture of Na2CO3 and Na2O2. The fusion cake is dissolved in distilled water, buffered with NH4Cl, and filtered to remove Si and the R2O3 group. A carrier solution of Na2TeO4, plus solid KI, hydrazine sulfate and Na2SO3, is added to the filtrate. The solution is then vacuum-filtered through a 0.45-??m pore-size filter disc. The filter, with the thin film of precipitate, is supported between two sheets of Mylar?? film for analysis. Good agreement is shown between data reported in this study and literature values reported by epithermal neutron-activation analysis and spectrofluorimetry. The method can be made quantitative by utilizing a secondary precipitation to assure complete recovery of the Se. The X-ray method offers fast turn-around time and a reasonably high production rate. ?? 1981.

Deashing of coal liquids with ceramic membrane microfiltration and diafiltration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bishop, B.; Goldsmith, R.

1995-12-31

Removal of mineral matter from liquid hydrocarbons derived from the direct liquefaction of coal is required for product acceptability. Current methods include critical solvent deashing (Rose{sup {reg_sign}} process from Kerr-McGee) and filtration (U.S. Filter leaf filter as used by British Coal). These methods produce ash reject streams containing up to 15% of the liquid hydrocarbon product. Consequently, CeraMem proposed the use of low cost, ceramic crossflow membranes for the filtration of coal liquids bottoms to remove mineral matter and subsequent diafiltration (analogous to cake washing in dead-ended filtration) for the removal of coal liquid from the solids stream. The usemore » of these ceramic crossflow membranes overcomes the limitations of traditional polymeric crossflow membranes by having the ability to operate at elevated temperature and to withstand prolonged exposure to hydrocarbon and solvent media. In addition, CeraMem`s membrane filters are significantly less expensive than competitive ceramic membranes due to their unique construction. With these ceramic membrane filters, it may be possible to reduce the product losses associated with traditional deashing processes at an economically attractive cost. The performance of these ceramic membrane microfilters is discussed.« less

SIDE VIEW OF PREPARATION FOR PULLING CONTINUOUSLYCAST "CAKES" FROM MOLDS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SIDE VIEW OF PREPARATION FOR PULLING CONTINUOUSLY-CAST "CAKES" FROM MOLDS AT #03 STATION. WHEN THE CAKES HAVE COOLED SUFFICIENTLY, THE CASTER STATION IS MOVED ASIDE TO EXPOSE THE QUENCH TANK AND MOLDS. EACH CAKE OF THE THREE CAKES WEIGHS UP TO APPROXIMATELY 20,000. THE DIMENSIONS OF BRASS CAKES RANGE UP TO 27 1\\2" WIDE X 6 3\\4" THICK X 25' LONG, CORRESPONDING MAXIMUMS FOR COPPER CAKES ARE 37 1\\2" X 5" X 24'. #01 STATION, DATING FROM THE EARLY 1960'S CASTS ONLY A SINGLE BAR (RATHER THAN THREE SIMULTANEOUSLY), THAT IS APPROXIMATELY HALF THE LENGTH OF CAKES FROM THE OTHER STATIONS (150' V. 300") AND WEIGHS UP TO 12,500 LBS. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

SIDE VIEW OF PREPARATION FOR PULLING CONTINUOUSLYCAST "CAKES" FROM MOLDS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

SIDE VIEW OF PREPARATION FOR PULLING CONTINUOUSLY-CAST "CAKES" FROM MOLDS AT #03 STATION. WHEN THE CAKES HAVE COOLED SUFFICIENTLY, THE CASTER STATION IS MOVED ASIDE TO EXPOSE THE QUENCH TANK AND MOLDS. EACH CAKE OF THE THREE CAKES WEIGHS UP TO APPROXIMATELY 20,000 LBS THE DIMENSIONS OF BRASS CAKES RANGE UP TO 27 1\\2" WIDE X 6 3\\4" THICK X 25' LONG, CORRESPONDING MAXIMUMS FOR COPPER CAKES ARE 37 1\\2" X 5" X 24'. #01 STATION, DATING FROM THE EARLY 1960'S CASTS ONLY A SINGLE BAR (RATHER THAN THREE SIMULTANEOUSLY), THAT IS APPROXIMATELY HALF THE LENGTH OF CAKES FROM THE OTHER STATIONS (150' V. 300") AND WEIGHS UP TO 12,500 LBS. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

Influence of solid-liquid separation method parameters employed in soil leaching tests on apparent metal concentration.

PubMed

Imoto, Yukari; Yasutaka, Tetsuo; Someya, Masayuki; Higashino, Kazuo

2018-05-15

Soil leaching tests are commonly used to evaluate the leachability of hazardous materials, such as heavy metals, from the soil. Batch leaching tests often enhance soil colloidal mobility and may require solid-liquid separation procedures to remove excess soil particles. However, batch leaching test results depend on particles that can pass through a 0.45μm membrane filter and are influenced by test parameters such as centrifugal intensity and filtration volume per filter. To evaluate these parameters, we conducted batch leaching experiments using metal-contaminated soils and focused on the centrifugal intensity and filtration volume per filter used in solid-liquid separation methods currently employed in standard leaching tests. Our experiments showed that both centrifugal intensity and filtration volume per filter affected the reproducibility of batch leaching tests for some soil types. The results demonstrated that metal concentrations in the filtrates significantly differed according to the centrifugal intensity when it was 3000 g for 2h or less. Increased filtration volume per filter led to significant decreases in filtrate metal concentrations when filter cakes formed during filtration. Comparison of the filtration tests using 0.10 and 0.45μm membrane filters showed statistically significant differences in turbidity and metal concentration. These findings suggest that colloidal particles were not adequately removed from the extract and contributed substantially to the apparent metal concentrations in the leaching test of soil containing colloidal metals. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

Physicochemical and functional properties of protein concentrate from by-product of coconut processing.

PubMed

Rodsamran, Pattrathip; Sothornvit, Rungsinee

2018-02-15

Coconut cake, a by-product from milk and oil extractions, contains a high amount of protein. Protein extraction from coconut milk cake and coconut oil cake was investigated. The supernatant and precipitate protein powders from both coconut milk and oil cakes were compared based on their physicochemical and functional properties. Glutelin was the predominant protein fraction in both coconut cakes. Protein powders from milk cake presented higher water and oil absorption capacities than those from oil cake. Both protein powders from oil cake exhibited better foaming capacity and a better emulsifying activity index than those from milk cake. Coconut proteins were mostly solubilized in strong acidic and alkaline solutions. Minimum solubility was observed at pH 4, confirming the isoelectric point of coconut protein. Therefore, the coconut residues after extractions might be a potential alternative renewable plant protein source to use asa food ingredient to enhance food nutrition and quality. Copyright © 2017 Elsevier Ltd. All rights reserved.

Cake properties in ultrafiltration of TiO2 fine particles combined with HA: in situ measurement of cake thickness by fluid dynamic gauging and CFD calculation of imposed shear stress for cake controlling.

PubMed

Du, Xing; Qu, Fangshu; Liang, Heng; Li, Kai; Chang, Haiqing; Li, Guibai

2016-05-01

In this study, the cake buildup of TiO2 fine particles in the presence of humid acid (HA) and cake layer controlling during ultrafiltration (UF) were investigated. Specifically, we measured the cake thickness using fluid dynamic gauging (FDG) method under various solution conditions, including TiO2 concentration (0.1-0.5 g/L), HA concentration (0-5 mg/L, total organic carbon (TOC)), and pH values (e.g., 4, 6 and 10), and calculated the shear stress distribution induced by stirring using computational fluid dynamics (CFD) to analyze the cake layer controlling conditions, including the operation flux (50-200 L m(-2) h(-1)) and TiO2 concentration (0.1-0.5 g/L). It was found that lower TiO2/HA concentration ratio could lead to exceedingly severe membrane fouling because of the formation of a relatively denser cake layer by filling the voids of cake layer with HA, and pH was essential for cake layer formation owing to the net repulsion between particles. Additionally, it was observed that shear stress was rewarding for mitigating cake growth under lower operation flux as a result of sufficient back-transport forces, and exhibited an excellent performance on cake layer controlling in lower TiO2 concentrations due to slight interaction forces on the vicinity of membrane.

Effect of wheat flour characteristics on sponge cake quality.

PubMed

Moiraghi, Malena; de la Hera, Esther; Pérez, Gabriela T; Gómez, Manuel

2013-02-01

To select the flour parameters that relate strongly to cake-making performance, in this study the relationship between sponge cake quality, solvent retention capacity (SRC) profile and flour physicochemical characteristics was investigated using 38 soft wheat samples of different origins. Particle size average, protein, damaged starch, water-soluble pentosans, total pentosans, SRC and pasting properties were analysed. Sponge cake volume and crumb texture were measured to evaluate cake quality. Cluster analysis was applied to assess differences in flour quality parameters among wheat lines based on the SRC profile. Cluster 1 showed significantly higher sponge cake volume and crumb softness, finer particle size and lower SRC sucrose, SRC carbonate, SRC water, damaged starch and protein content. Particle size, damaged starch, protein, thickening capacity and SRC parameters correlated negatively with sponge cake volume, while total pentosans and pasting temperature showed the opposite effect. The negative correlations between cake volume and SRC parameters along with the cluster analysis results indicated that flours with smaller particle size, lower absorption capacity and higher pasting temperature had better cake-making performance. Some simple analyses, such as SRC, particle size distribution and pasting properties, may help to choose flours suitable for cake making. Copyright © 2012 Society of Chemical Industry.

Structural development of sucrose-sweetened and sucrose-free sponge cakes during baking.

PubMed

Baeva, Marianna Rousseva; Terzieva, Vesselina Velichkova; Panchev, Ivan Nedelchev

2003-06-01

The influence of sucrose, wheat starch and sorbitol upon the heat- and mass-exchanging processes forming the structure of sponge cake was studied. Under the influence of wheat starch and sorbitol the structure of the sucrose-free sponge cake was formed at more uniform total moisture release. This process was done at lower temperatures and smoother change of the sponge cake height with respect to the sucrose-sweetened sponge cake. The porous and steady structure of both cakes was finally formed at identical time--between 18th and 19th minute, at the applied conditions for baking of each batter (metal pan with diameter 15.4 cm and depth 6.2 cm containing 300 g of batter and placed in an electric oven "Rahovetz-02", Bulgaria for 30 min at 180 degrees C). The water-losses at the end of baking (10.30% and 10.40% for the sucrose-sweetened cake and sucrose-free cake, respectively) and the final temperatures reached in the crumb central layers (96.6 degrees C and 96.3 degrees C for the sucrose-sweetened cake and sucrose-free cake, respectively) during baking of both samples were not statistically different. The addition of wheat starch and sorbitol in sucrose-free sponge cake lead to the statistically different values for the porosity (76.15% and 72.98%) and the volume (1014.17 cm3 and 984.25 cm3) of the sucrose-sweetened and sucrose-free sponge cakes, respectively. As a result, the sucrose-free sponge cake formed during baking had a more homogeneous and finer microstructure with respect to that ofthe sucrose-sweetened one.

Investigation of the influence of the zeta-potential on the filtration rate in the presence of collectors

NASA Technical Reports Server (NTRS)

Provirnina, E. V.; Barbin, M. B.

1984-01-01

The value of the zeta-potential does not have an explicit effect, which is expressed by a simple math correlation, on filtration rate when a solution of the tested collector is filtered through a cake prepared under standard conditions from the examined particulate material. The zeta-potential measurements and filtration tests were carried out on silica and galena with solutions contg. a cationic container ANP and Et xanthane, resp. at PH = 6.5, varying concentration of the agent (0-2500 g/ton), and under a vacuum of 100 to 600 mm Hg.

Genetically Modified Flax Expressing NAP-SsGT1 Transgene: Examination of Anti-Inflammatory Action

PubMed Central

Matusiewicz, Magdalena; Kosieradzka, Iwona; Zuk, Magdalena; Szopa, Jan

2014-01-01

The aim of the work was to define the influence of dietary supplementation with GM (genetically modified) GT#4 flaxseed cake enriched in polyphenols on inflammation development in mice liver. Mice were given ad libitum isoprotein diets: (1) standard diet; (2) high-fat diet rich in lard, high-fat diet enriched with 30% of (3) isogenic flax Linola seed cake; and (4) GM GT#4 flaxseed cake; for 96 days. Administration of transgenic and isogenic seed cake lowered body weight gain, of transgenic to the standard diet level. Serum total antioxidant status was statistically significantly improved in GT#4 flaxseed cake group and did not differ from Linola. Serum thiobarbituric acid reactive substances, lipid profile and the liver concentration of pro-inflammatory cytokine tumor necrosis factor-α were ameliorated by GM and isogenic flaxseed cake consumption. The level of pro-inflammatory cytokine interferon-γ did not differ between mice obtaining GM GT#4 and non-GM flaxseed cakes. The C-reactive protein concentration was reduced in animals fed GT#4 flaxseed cake and did not differ from those fed non-GM flaxseed cake-based diet. Similarly, the liver structure of mice consuming diets enriched in flaxseed cake was improved. Dietetic enrichment with GM GT#4 and non-GM flaxseed cakes may be a promising solution for health problems resulting from improper diet. PMID:25247574

Effect of selected spices on chemical and sensory markers in fortified rye-buckwheat cakes.

PubMed

Przygodzka, Małgorzata; Zieliński, Henryk; Ciesarová, Zuzana; Kukurová, Kristina; Lamparski, Grzegorz

2016-07-01

The aim of this study was to find out the effect of selected spices on chemical and sensorial markers in cakes formulated on rye and light buckwheat flour fortified with spices. Among collection of spices, rye-buckwheat cakes fortified individually with cloves, nutmeg, allspice, cinnamon, vanilla, and spice mix revealed the highest sensory characteristics and overall quality. Cakes fortified with cloves, allspice, and spice mix showed the highest antioxidant capacity, total phenolics, rutin, and almost threefold higher available lysine contents. The reduced furosine content as well as free and total fluorescent intermediatory compounds were observed as compared to nonfortified cakes. The FAST index was significantly lowered in all cakes enriched with spices, especially with cloves, allspice, and mix. In contrast, browning index increased in compare to cakes without spices. It can be suggested that clove, allspice, vanilla, and spice mix should be used for production of safety and good quality cakes.

Effects of dilute-acid pretreatment conditions on filtration performance of corn stover hydrolyzate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sievers, David A.; Kuhn, Erik M.; Tucker, Melvin P.

In this study, the reaction conditions used during dilute-acid pretreatment of lignocellulosic biomass control the carbohydrate digestion yield and also hydrolyzate properties. Depending on the conversion route of interest, solid-liquid separation (SLS) may be required to split the hemicellulose-rich liquor from the cellulose-rich insoluble solids, and slurry properties are important for SLS. Corn stover was pretreated at different reaction conditions and the slurries were assessed for conversion yield and filtration performance. Increasing pretreatment temperature reduced the solids mean particle size and resulted in slower slurry filtration rates when vacuum filtered or pressure filtered. Corn stover pretreated at 165 °C formore » 10 min and with 1% H 2SO 4 exhibited the highest xylose yield and best filtration performance with a no-wash filtration rate of 80 kg/h m 2 and cake permeability of 15 x 10 -15.« less

Effects of dilute-acid pretreatment conditions on filtration performance of corn stover hydrolyzate

DOE PAGES

Sievers, David A.; Kuhn, Erik M.; Tucker, Melvin P.; ...

2017-06-28

In this study, the reaction conditions used during dilute-acid pretreatment of lignocellulosic biomass control the carbohydrate digestion yield and also hydrolyzate properties. Depending on the conversion route of interest, solid-liquid separation (SLS) may be required to split the hemicellulose-rich liquor from the cellulose-rich insoluble solids, and slurry properties are important for SLS. Corn stover was pretreated at different reaction conditions and the slurries were assessed for conversion yield and filtration performance. Increasing pretreatment temperature reduced the solids mean particle size and resulted in slower slurry filtration rates when vacuum filtered or pressure filtered. Corn stover pretreated at 165 °C formore » 10 min and with 1% H 2SO 4 exhibited the highest xylose yield and best filtration performance with a no-wash filtration rate of 80 kg/h m 2 and cake permeability of 15 x 10 -15.« less

Production of staphylococcal enterotoxin A in cream-filled cake.

PubMed

Anunciaçao, L L; Linardi, W R; do Carmo, L S; Bergdoll, M S

1995-07-01

Cakes were baked with normal ingredients and filled with cream, inoculated with different size enterotoxigenic-staphylococcal inocula. Samples of the cakes were incubated at room temperature and put in the refrigerator. Samples of cake and filling were taken at different times and analyzed for staphylococcal count and presence of enterotoxin. The smaller the inoculum, the longer the time required for sufficient growth (10(6)) to occur for production of detectable enterotoxin. Enterotoxin added to the cake dough before baking (210 degrees C, 45 min) did not survive the baking. The presence of enterotoxin in the contaminated cream filling indicated this as the cause of staphylococcal food poisoning from cream-filled cakes. Refrigeration of the cakes prevented the growth of the staphylococci.

Effect of transglutaminase on some properties of cake enriched with various protein sources.

PubMed

Alp, H; Bilgiçli, N

2008-06-01

The effect of transglutaminase (TG) enzyme addition (0% and 0.09%) on batter and cake properties, prepared with different protein sources (nonfat dry milk [NFDM], soy flour, and soymilk) and flour types (type A with 11.4% protein and type B with 8.6% protein), was investigated. Specific gravity and pH of cake batters were determined, and physical and chemical analysis of the cake samples was performed. Soy products improved cake weight, volume, softness, protein, and fat contents. NFDM increased the crust redness and crumb lightness more than the other protein sources. TG enzyme addition affected the volume, softness, crust, and crumb color of the cake samples significantly (P < 0.05). The combination of TG enzyme and flour B with lower protein gave more puffed, symmetrical, and softer cake samples. TG had a potential application with different protein sources in cake production. Especially interactions between TG with soy flour and TG and wheat flour with high protein content were important in cake formulations due to the softening effect on crumb.

Mechanistic modeling of the loss of protein sieving due to internal and external fouling of microfilters.

PubMed

Bolton, Glen R; Apostolidis, Alex J

2017-09-01

Fed-batch and perfusion cell culture processes used to produce therapeutic proteins can use microfilters for product harvest. In this study, new explicit mathematical models of sieving loss due to internal membrane fouling, external membrane fouling, or a combination of the two were generated. The models accounted for membrane and cake structures and hindered solute transport. Internal membrane fouling was assumed to occur due to the accumulation of foulant on either membrane pore walls (pore-retention model) or membrane fibers (fiber-retention model). External cake fouling was assumed to occur either by the growth of a single incompressible cake layer (cake-growth) or by the accumulation of a number of independent cake layers (cake-series). The pore-retention model was combined with either the cake-series or cake-growth models to obtain models that describe internal and external fouling occurring either simultaneously or sequentially. The models were tested using well-documented sieving decline data available in the literature. The sequential pore-retention followed by cake-growth model provided a good fit of sieving decline data during beer microfiltration. The cake-series and cake-growth models provided good fits of sieving decline data during the microfiltration of a perfusion cell culture. The new models provide insights into the mechanisms of fouling that result in the loss of product sieving. © 2017 American Institute of Chemical Engineers Biotechnol. Prog., 33:1323-1333, 2017. © 2017 American Institute of Chemical Engineers.

Research on wall shear stress considering wall roughness when shear swirling flow vibration cementing

NASA Astrophysics Data System (ADS)

Cui, Zhihua; Ai, Chi; Feng, Fuping

2017-01-01

When shear swirling flow vibration cementing, the casing is revolving periodically and eccentrically, which leads to the annulus fluid in turbulent swirling flow state. The wall shear stress is more than that in laminar flow field when conventional cementing. The paper mainly studied the wall shear stress distribution on the borehole wall when shear swirling flow vibration cementing based on the finite volume method. At the same time, the wall roughness affected and changed the turbulent flow near the borehole wall and the wall shear stress. Based on the wall function method, the paper established boundary conditions considering the wall roughness and derived the formula of the wall shear stress. The results showed that the wall roughness significantly increases the wall shear stress. However, the larger the wall roughness, the greater the thickness of mud cake, which weakening the cementing strength. Considering the effects in a comprehensive way, it is discovered that the particle size of solid phase in drilling fluid is about 0.1 mm to get better cementing quality.

Utilization of deoiled Jatropha curcas seed cake for production of xylanase from thermophilic Scytalidium thermophilum.

PubMed

Joshi, Chetna; Khare, S K

2011-01-01

Jatropha curcas is a major biodiesel crop. Large amount of deoiled cake is generated as by-product during biodiesel production from its seeds. Deoiled J. curcas seed cake was assessed as substrate for the production of xylanase from thermophilic fungus Scytalidium thermophilum by solid-state fermentation. The seed cake was efficiently utilized by S. thermophilum for its growth during which it produced good amount of heat stable extracellular xylanase. The solid-state fermentation conditions were optimized for maximum xylanase production. Under the optimized conditions viz. deoiled seed cake supplemented with 1% oat-spelt xylan, adjusted to pH 9.0, moisture content 1:3 w/v, inoculated with 1×10(6) spores per 5 g cake and incubated at 45 °C, 1455 U xylanase/g deoiled seed cake was obtained. The xylanase was useful in biobleaching of paper pulp. Solid-state fermentation of deoiled cake appears a potentially viable approach for its effective utilization. Copyright © 2010 Elsevier Ltd. All rights reserved.

Utilization of Oleogels as a Replacement for Solid Fat in Aerated Baked Goods: Physicochemical, Rheological, and Tomographic Characterization.

PubMed

Kim, Joo Young; Lim, Jeongtaek; Lee, JaeHwan; Hwang, Hong-Sik; Lee, Suyong

2017-02-01

Canola oil-carnauba wax oleogels were evaluated as a replacement for shortening in a baked cake system. The use of oleogels produced cake batters with a lower pseudoplastic property and also contributed to their viscous nature. The shortening replacement with oleogels at up to 50% was effective in maintaining the ability to hold air cells into the cake batters. The volume of cakes had an overall tendency to decrease with increasing shortening replacement with oleogels, leading to increased cake firmness. The tomographic analysis demonstrated that the total porosity and fragmentation index were reduced in the oleogel cakes, showing a more connected solid structure. The levels of saturated fatty acids in the cakes containing oleogels were significantly reduced to 13.3%, compared to the control with shortening (74.2%). As a result, the use of oleogels for shortening up to 25% produced cakes with lower levels of saturated fatty acids without quality loss. © 2016 Institute of Food Technologists®.

Evaluation of antioxidant, rheological, physical and sensorial properties of wheat flour dough and cake containing turmeric powder.

PubMed

Park, S H; Lim, H S; Hwang, S Y

2012-10-01

The effects of addition of turmeric powder (0%, 2%, 4%, 6% and 8%) were examined in order to obtain an antioxidant-enriched cake with good physico-chemical and sensorial properties. The rheological properties of doughs were evaluated using dynamic rheological measurements. Physical properties, curcumin content, radical scavenging activity (RSA-DPPH assay) and sensory analysis (hedonic test) of the supplemented cake were determined. Addition of turmeric powder up to 8% caused significant changes on dough characteristics and on cake rheological properties. The highest curcumin (203 mg/kg) and RSA-DPPH activity (45%) were achieved in the cake having the highest percentage of turmeric powder (8%); however, this sample showed the worst results regarding the rheological properties. Moreover, by sensory evaluation this cake sample was not acceptable. A 6% substitution of wheat flour with turmeric powder showed acceptable sensory scores which were comparable to those of 0-4% turmeric cakes. This indicated that up to 6% level of turmeric powder might be included in cake formulation.

Effect of adding palm oil mill decanter cake slurry with regular turning operation on the composting process and quality of compost from oil palm empty fruit bunches.

PubMed

Yahya, Azmi; Sye, Chong Puay; Ishola, Tajudeen Abiodun; Suryanto, Hadi

2010-11-01

Formation of compost from oil palm empty fruit bunches (EFB) and decanter cake slurry by adding palm oil mill effluent (POME) with regular turning operation was investigated. The experiment was conducted in a commercial composting plant under the normal production process. The addition of decanter cake slurry has hastened the composting process of the EFB. The C/N ratio after 51 days for the mature compost with the decanter cake slurry was 18.65 while that of the matured compost without the decanter cake slurry remained high at 28.96. The compost formed from the addition of decanter cake to EFB and POME had 46.4% nitrogen, 17.9% phosphorus, 17.7% potassium and 23.1% calcium more than that without decanter cake. The use of compost produced from EFB, POME and decanter cake slurry could solve more environmental problems and enhance economic benefits in the oil palm industry.

Influence of waxy rice flour substitution for wheat flour on characteristics of batter and freeze-thawed cake.

PubMed

Jongsutjarittam, Nisachon; Charoenrein, Sanguansri

2013-09-12

This study aimed to improve the freeze-thawed cake properties by10-20% waxy rice flour (WRF) substitution for wheat flour (WF). Viscosity of WRF-substituted batters was lower; consequently, trapped air was less uniformly distributed than WF batter. After five freeze-thaw cycles, firmness and enthalpy of melting retrograded amylopectin of WF- and WRF-substituted cakes increased and the matrix surrounding the air pores from SEM images was denser than in fresh-baked cakes. Sensory evaluation showed an increase in firmness and a decrease in firmness acceptability of freeze-thawed cakes. However, freeze-thawed cake with WRF substitution had significantly less firmness, less dense matrix and more acceptability than WF cake. This could have been due to a low amylose content of WRF and the spread of ruptured waxy rice starch granules around swollen wheat starch granules as observed by CLSM. Thus, WRF could be used for WF substitution to improve the firmness in freeze-thawed cake. Copyright © 2013 Elsevier Ltd. All rights reserved.

Rheological, physical, and sensory attributes of gluten-free rice cakes containing resistant starch.

PubMed

Tsatsaragkou, Kleopatra; Papantoniou, Maria; Mandala, Ioanna

2015-02-01

In this study the effect of resistant starch (RS) addition on gluten-free cakes from rice flour and tapioca starch physical and sensorial properties was investigated. Increase in RS concentration made cake batters less elastic (drop of G'(ω), G''(ω) values) and thinner (viscosity decreased). Cakes specific volume increased with an increase in RS level and was maximized for 15 g/100 g RS, although porosity values were significantly unaffected by RS content. Crumb grain analysis exhibited a decrease in surface porosity, number of pores and an increase in average pore diameter as RS concentration increased. During storage, cake crumb remained softer in formulations with increasing amounts of RS. Sensory evaluation of cakes demonstrated the acceptance of all formulations, with cake containing 20 g/100 g RS mostly preferred. Gluten-free cakes with improved quality characteristics and high nutritional value can be manufactured by the incorporation of RS. © 2015 Institute of Food Technologists®

Utilisation of preharvest dropped apple peels as a flour substitute for a lower glycaemic index and higher fibre cake.

PubMed

Jun, Yujin; Bae, In Young; Lee, Suyong; Lee, Hyeon Gyu

2014-02-01

Fibre-enriched materials (FEMs) obtained from preharvest dropped apple peels were utilised as a source of dietary fibre in baked cakes and their effects on the textural/nutritional qualities and starch digestibility (glucose release behaviour, starch digestion fraction, predicted glycaemic index) of the cakes were evaluated. When FEMs were incorporated into the cake formulation (3 g and 6 g of dietary fibre per serving (100 g)), the volume of the cakes seemed to be reduced and their texture become harder. However, 3 g of FEMs did not degrade the cake qualities. The use of FEMs in cakes significantly reduced the levels of rapidly digestible starch and slowly digestible starch, while the levels of resistant starch increased. Additionally, the cake samples prepared with FEMs exhibited a lower predicted glycaemic index. This study may give rise to multi-functional bakery products with acceptable quality and low glycaemic index.

Ethanol production from rice winery waste-rice wine cake by simultaneous saccharification and fermentation without cooking.

PubMed

Vu, Van Hanh; Kim, Keun

2009-10-01

Ethanol production by simultaneous saccharification and fermentation (SSF) of low-value rice wine cake (RWC) without cooking was investigated. RWC is the filtered solid waste of fermented rice wine mash and contains 53% of raw starch. RWC slurry was mixed with raw-starch-digesting enzyme of Rhizopus sp. and yeast for SSF. The yeast strain used was selected from 300 strains for RWC fermentation and identified as Saccharomyces cerevisiae KV25. High efficiency (94%) of ethanol production was achieved at optimal condition of uncooked RWC slurry containing 23.03% of starch. The optimal SSF condition determined was 1.125 unit of raw-starch-digesting enzyme per one gram of RWC, 30 degrees C of fermentation temperature, 4.5 of pH slurry, 36 h-age of seeding culture, initial yeast cell 2 x 10(7) per ml slurry, 17 mM urea as nitrogen additive, 0.25 mM Cu(2+) as metal ion additives, 90 h of fermentation time. In this optimal condition, ethanol production by SSF of uncooked RWC slurry was improved to 16.8% (v/v) from 15.1% (v/v) of pre-optimization.

Brettanomyces as a starter culture in rice-steamed sponge cake: a traditional fermented food in China.

PubMed

Wu, Peng; Xu, Xiaoyun; Xu, Yongxia; Chen, Qingchan; Pan, Siyi

2011-11-01

The potential use of Brettanomyces anomalus PSY-001 as an additional starter culture for the production of Rice-steamed sponge cake (RSSC), a traditional fermented food in China, was investigated. Two productions of RSSC, each containing batches of experimental cakes with Brettanomyces added and reference cakes with the leavened liquid added were carried out. For both experimental and reference cakes, chemical analysis and sensory evaluation were carried out during the fermentation period. The results showed that experimental cakes had desirable aroma and taste. The observed differences indicate a positive contribution to the overall quality of RSSC by B. anomalus PSY-001.

Intake, digestibility, nitrogen balance, performance, and carcass yield of lambs fed licuri cake.

PubMed

Costa, J B; Oliveira, R L; Silva, T M; Ribeiro, R D X; Silva, A M; Leão, A G; Bezerra, L R; Rocha, T C

2016-07-01

This study aimed to determine the impact of the inclusion of licuri cake in the diets of crossbred Santa Inês lambs, based on intake, digestibility, N balance, urea N, and performance. We used 44 male lambs that were vaccinated and wormed, with an average age of 6 mo and an average BW of 21.2 kg ± 2.7 kg. The lambs were fed a mixture of Tifton-85 hay (40%) and a concentrated mixture (60%) composed of ground corn, soybean meal, and mineral premix. For the treatments, licuri cake was added at levels of 0, 8, 16, and 24% of DM, with the licuri cake replacing soybean meal and ground corn. We used 11 lambs per treatment in a randomized design. The lambs were confined for 70 d, and the digestibility trial occurred between Day 40 and Day 55. The increased level of licuri cake inclusion promoted a linear reduction in DM intake ( = 0.00) with a 39% reduction between treatments with the 0 and 24% cakes. On the other hand, ether extract () consumption showed an initial quadratic increase ( = 0.00). The total weight gain and ADG showed a linear decrease ( = 0.00) with the addition of licuri cake. The inclusion of licuri cake linearly enhanced ( = 0.02) the digestibility of CP and EE, whereas the digestibility of other nutrients in lambs remained unchanged ( > 0.05). The licuri cake increase led to a linear decrease ( < 0.05) in the N intake, fecal N, and retained N in lambs. Urinary N was not changed. The slaughter carcass weight, HCW, cold carcass weight, hot carcass yield, and cold carcass yield showed linear decreases ( < 0.05) with the addition of licuri cake. Carcass morphometric measurements were influenced by experimental diets, showing linear decreases ( < 0.05) with the addition of licuri cake to diets. The fat thickness, conformation, external length, internal length, leg length, rump width, and chest circumference showed linear decreases ( < 0.05) with the inclusion of licuri cake in diets. The inclusion of licuri cake decreased DMI and digestibility, reflecting the lower ADG. Although feed efficiency was not affected, the lambs weighed less at slaughter and the licuri cake had a negative impact on carcass yield. Therefore, the use of the studied levels of licuri cake in diets for finishing lambs cannot be recommended.

Short-term effects of sugarcane waste products from ethanol production plant as soil amendments on sugarcane growth and metal stabilization.

PubMed

Akkajit, Pensiri; DeSutter, Thomas; Tongcumpou, Chantra

2013-05-01

Numerous waste products have been widely studied and used as soil amendments and metal immobilizing agents. Waste utilization from ethanol production processes as soil amendments is one of the most promising and sustainable options to help utilize materials effectively, reduce waste disposal, and add value to byproducts. As a consequence, this present work carried out a four-month pot experiment of sugarcane (Saccharum officinarum L.) cultivation in Cd and Zn contaminated soil to determine the effect of three sugarcane waste products (boiler ash, filter cake and vinasse) as soil amendment on sugarcane growth, metal translocation and accumulation in sugarcane, and fractionation of Cd and Zn in soil by the BCR sequential extraction. Four treatments were tested: (1) non-amended soil; (2) 3% w/w boiler ash; (3) 3% w/w filter cake; and (4) a combination of 1.5% boiler ash and 1.5% vinasse (w/w). Our findings showed the improved biomass production of sugarcanes; 6 and 3-fold higher for the above ground parts (from 8.5 to 57.6 g per plant) and root (from 2.1 to 6.59 g per plant), respectively, as compared to non-amended soil. Although there was no significant difference in Cd and Zn uptake in sugarcane (mg kg(-1)) between the non-amended soil and the treated soils (0.44 to 0.52 mg Cd kg(-1) and 39.9 to 48.1 mg Zn kg(-1), respectively), the reduction of the most bioavailable Cd concentration (BCR1 + 2) in the treated soils (35.4-54.5%) and the transformation of metal into an insoluble fraction (BCR3) highlighted the beneficial effects of sugarcane waste-products in promoting the sugarcane growth and Cd stabilization in soil.

Non-Caking Freeze Dried Applesauce

DTIC Science & Technology

A study was initiated to develop an applesauce which resists caking when subjected to elevated temperatures such as 37.7C. for two weeks and/or 57C...following results were obtained: (1) The degree of caking of the freeze dried applesauce powder was correlated with the amount of juice extracted. (2... applesauce powders. (3) Reducing sugars appear to be the factor contributing most significantly to the caking with the higher reducing sugar levels producing the higher degrees of caking.

Bioassay directed identification of toxicants in sludge and related reused materials from industrial wastewater treatment plants in the Yangtze River Delta.

PubMed

Fang, Binbin; Guo, Jing; Li, Fuxing; Giesy, John P; Wang, Lianjun; Shi, Wei

2017-02-01

Industrialized development of the Yangtze River Delta, China, has resulted in larger amounts of wastes, including sludges from treatment of these wastes. Methods to manage and dispose, including reuse were urgently needed. Sludge and reused products were collected from two largest factories, KEYUAN and HENGJIA where treated sludges were turned into bricks or sludge cake to be placed in landfills, respectively. Metals and organic compounds were quantified in sludges and leachates assessed by use of toxicity characterized leaching procedure (TCLP) while acute toxicity was determined by Daphnia magna. Nine metals were detected in all raw sludges with concentrations of Cr and Ni exceeding Chinese standards. For sludge leachate, concentrations of metals were all less than Chinese standards, which changed little after being made into cake by HENGJIA, but were significantly less after being made into brick by KEYUAN. Toxicity units (TU) for all samples are greater than 1.0 indicating that they are potentially toxic to aquatic organisms. TUs changed little after being made into filter cake, but were 10-fold less after being made into bricks. Cr and Ni contributed most to the total toxicity followed by Zn and Cu. Making of sludges into K-brick 1 resulted in better inactivation of contaminants, which resulted in less toxic potencies. So that is the recommended method for handling of industrial sludges. To further assure their safe reuse, additional research on identification of key toxicants and potential hazards, based on additional endpoints, by combining bio-tests and chemical analysis should be done for reused sludges. Copyright © 2016 Elsevier Ltd. All rights reserved.

Particle emissions from diesel passenger cars equipped with a particle trap in comparison to other technologies.

PubMed

Mohr, Martin; Forss, Anna-Maria; Lehmann, Urs

2006-04-01

Tail pipe particle emissions of passenger cars, with different engine and aftertreatment technologies, were determined with special focus on diesel engines equipped with a particle filter. The particle number measurements were performed, during transient tests, using a condensation particle counter. The measurement procedure complied with the draft Swiss ordinance, which is based on the findings of the UN/ECE particulate measurement program. In addition, particle mass emissions were measured by the legislated and a modified filter method. The results demonstrate the high efficiency of diesel particle filters (DPFs) in curtailing nonvolatile particle emissions over the entire size range. Higher emissions were observed during short periods of DPF regeneration and immediately afterward, when a soot cake has not yet formed on the filter surface. The gasoline vehicles exhibited higher emissions than the DPF equipped diesel vehicles but with a large variation depending on the technology and driving conditions. Although particle measurements were carried out during DPF regeneration, it was impossible to quantify their contribution to the overall emissions, due to the wide variation in intensity and frequency of regeneration. The numbers counting method demonstrated its clear superiority in sensitivity to the mass measurement. The results strongly suggest the application of the particle number counting to quantify future low tailpipe emissions.

Ultrasonic wave propagation in powders

NASA Astrophysics Data System (ADS)

Al-Lashi, R. S.; Povey, M. J. W.; Watson, N. J.

2018-05-01

Powder clumps (cakes) has a significant effect on the flowability and stability of powders. Powder caking is mainly caused by moisture migration due to wetting and environmental (temperature and humidity) changes. The process of moisture migration caking involves creating liquid bridges between the particles during condensation which subsequently harden to form solid bridges. Therefore, an effective and reliable technique is required to quantitatively and non-invasively monitor caking kinetics and effective stiffness. This paper describes two ultrasonic instruments (ultrasonic velocity pulse and airborne ultrasound systems) that have been used to monitor the caking phenomenon. Also, it discusses the relationship between the ultrasonic velocity and attenuation measurements and tracking caking kinetics and the effective stiffness of powders.

Physicochemical and Sensory Characteristics of Sponge Cakes with Rubus coreanus Powder

PubMed Central

Lee, Jun Ho

2015-01-01

To develop new type of sponge cake, the effects of partial (0~40%) replacement with Rubus coreanus powder (RCP) on the quality characteristics of sponge cakes were investigated. The pH level and moisture content ranged from 4.05~8.23 and 28.49~36.59, respectively, and significantly decreased upon addition of RCP (P<0.05). Baking loss rate and cake firmness significantly increased with higher RCP content in the formulation, whereas morphological characteristics of cakes such as height, volume, and symmetry indices significantly decreased (P<0.05). For crumb color values, L*- and b*-values significantly decreased while a*-value significantly increased as a result of RCP substitution (P<0.05). Hedonic sensory results indicated that sponge cakes supplemented with 30~40% RCP showed the most favorable acceptance scores for most of the sensory attributes evaluated. Overall, Rubus coreanus sponge cake could be developed with comparable physicochemical qualities without sacrificing consumer acceptability. PMID:26451358

Physicochemical and Sensory Characteristics of Sponge Cakes with Rubus coreanus Powder.

PubMed

Lee, Jun Ho

2015-09-01

To develop new type of sponge cake, the effects of partial (0~40%) replacement with Rubus coreanus powder (RCP) on the quality characteristics of sponge cakes were investigated. The pH level and moisture content ranged from 4.05~8.23 and 28.49~36.59, respectively, and significantly decreased upon addition of RCP (P<0.05). Baking loss rate and cake firmness significantly increased with higher RCP content in the formulation, whereas morphological characteristics of cakes such as height, volume, and symmetry indices significantly decreased (P<0.05). For crumb color values, L*- and b*-values significantly decreased while a*-value significantly increased as a result of RCP substitution (P<0.05). Hedonic sensory results indicated that sponge cakes supplemented with 30~40% RCP showed the most favorable acceptance scores for most of the sensory attributes evaluated. Overall, Rubus coreanus sponge cake could be developed with comparable physicochemical qualities without sacrificing consumer acceptability.

40 CFR 417.190 - Applicability; description of the manufacture of detergent bars and cakes subcategory.

Code of Federal Regulations, 2010 CFR

2010-07-01

... manufacture of detergent bars and cakes subcategory. 417.190 Section 417.190 Protection of Environment... POINT SOURCE CATEGORY Manufacture of Detergent Bars and Cakes Subcategory § 417.190 Applicability; description of the manufacture of detergent bars and cakes subcategory. The provisions of this subpart are...

Nutrition quality of extraction mannan residue from palm kernel cake on brolier chicken

NASA Astrophysics Data System (ADS)

Tafsin, M.; Hanafi, N. D.; Kejora, E.; Yusraini, E.

2018-02-01

This study aims to find out the nutrient residue of palm kernel cake from mannan extraction on broiler chicken by evaluating physical quality (specific gravity, bulk density and compacted bulk density), chemical quality (proximate analysis and Van Soest Test) and biological test (metabolizable energy). Treatment composed of T0 : palm kernel cake extracted aquadest (control), T1 : palm kernel cake extracted acetic acid (CH3COOH) 1%, T2 : palm kernel cake extracted aquadest + mannanase enzyme 100 u/l and T3 : palm kernel cake extracted acetic acid (CH3COOH) 1% + enzyme mannanase 100 u/l. The results showed that mannan extraction had significant effect (P<0.05) in improving the quality of physical and numerically increase the value of crude protein and decrease the value of NDF (Neutral Detergent Fiber). Treatments had highly significant influence (P<0.01) on the metabolizable energy value of palm kernel cake residue in broiler chickens. It can be concluded that extraction with aquadest + enzyme mannanase 100 u/l yields the best nutrient quality of palm kernel cake residue for broiler chicken.

Study of hydroxymethylfurfural and furfural formation in cakes during baking in different ovens, using a validated multiple-stage extraction-based analytical method.

PubMed

Petisca, Catarina; Henriques, Ana Rita; Pérez-Palacios, Trinidad; Pinho, Olívia; Ferreira, Isabel M P L V O

2013-12-15

A procedure for extraction of hydroxymethylfurfural (HMF) and furfural from cakes was validated. Higher yield was achieved by multiple step extraction with water/methanol (70/30) and clarification with Carrez I and II reagents. Oven type and baking time strongly influenced HMF, moisture and volatile profile of model cakes, whereas furfural content was not significantly affected. No correlation was found between these parameters. Baking time influenced moisture and HMF formation in cakes from traditional and microwave ovens but not in steam oven cakes. Significant moisture decrease and HMF increase (3.63, 9.32, and 41.9 mg kg(-1)dw at 20, 40 and 60 min, respectively) were observed during traditional baking. Cakes baked by microwave also presented a significant increase of HMF (up to 16.84 mg kg(-1)dw at 2.5 min). Steam oven cakes possessed the highest moisture content and no significant differences in HMF and furfural. This oven is likely to form low HMF and furfural, maintaining cake moisture and aroma compounds. Copyright © 2013 Elsevier Ltd. All rights reserved.

Chia (Salvia hispanica L) gel can be used as egg or oil replacer in cake formulations.

PubMed

Borneo, Rafael; Aguirre, Alicia; León, Alberto E

2010-06-01

This study determined the overall acceptability, sensory characteristics, functional properties, and nutrient content of cakes made using chia (Salvia hispanica L) gel as a replacement for oil or eggs. Chia gel was used to replace 25%, 50%, and 75% of oil or eggs in a control cake formulation. Seventy-five untrained panelists participated in rating cakes on a seven-point hedonic scale. Analysis of variance conducted on the sensory characteristics and overall acceptability indicated a statistically significant effect when replacing oil or eggs for color, taste, texture, and overall acceptability (P<0.05). Post hoc analysis (using Fisher's least significant difference method) indicated that the 25% chia gel cakes were not significantly different from the control for color, taste, texture, and overall acceptability. The 50% oil substituted (with chia gel) cake, compared to control, had 36 fewer kilocalories and 4 g less fat per 100-g portion. Cake weight was not affected by chia gel in the formulation, although cake volume was lower as the percentage of substitution increased. Symmetry was generally not affected. This study demonstrates that chia gel can replace as much as 25% of oil or eggs in cakes while yielding a more nutritious product with acceptable sensory characteristics. 2010 American Dietetic Association. Published by Elsevier Inc. All rights reserved.

Moisture-induced caking of beverage powders.

PubMed

Chávez Montes, Edgar; Santamaría, Nadia Ardila; Gumy, Jean-Claude; Marchal, Philippe

2011-11-01

Beverage powders can exhibit caking during storage due to high temperature and moisture conditions, leading to consumer dissatisfaction. Caking problems can be aggravated by the presence of sensitive ingredients. The caking behaviour of cocoa beverage powders, with varying amounts of a carbohydrate sensitive ingredient, as affected by climate conditions was studied in this work. Sorption isotherms of beverage powders were determined at water activities (a(w) ) ranging from 0.1 to 0.6 in a moisture sorption analyser by gravimetry and fitted to the Brunauer-Emmett-Teller (BET) or the Guggenheim-Anderson-de Boer (GAB) equation. Glass transition temperatures (T(g) ) at several a(w) were analysed by differential scanning calorimetry and fitted to the Gordon-Taylor equation. Deduced T(g) = f(a(w) ) functions helped to identify stability or caking zones. Specific experimental methods, based on the analysis of mechanical properties of powder cakes formed under compression, were used to quantify the degree of caking. Pantry tests complemented this study to put in evidence the visual perception of powder caking with increasing a(w) . The glass transition approach was useful to predict the risks of caking but was limited to products where T(g) can be measured. On the other hand, quantification of the caking degree by analysis of mechanical properties allowed estimation of the extent of degradation for each product. This work demonstrated that increasing amounts of a carbohydrate sensitive ingredient in cocoa beverages negatively affected their storage stability. Copyright © 2011 Society of Chemical Industry.

Experimental assessment of toxic phytochemicals in Jatropha curcas: oil, cake, bio-diesel and glycerol.

PubMed

Pradhan, Subhalaxmi; Naik, S N; Khan, M Ashhar I; Sahoo, P K

2012-02-01

Jatropha curcas seed is a rich source of oil; however, it can not be utilised for nutritional purposes due to presence of toxic and anti-nutritive compounds. The main objective of the present study was to quantify the toxic phytochemicals present in Indian J. curcas (oil, cake, bio-diesel and glycerol). The amount of phorbol esters is greater in solvent extracted oil (2.8 g kg⁻¹) than in expeller oil (2.1 g kg⁻¹). Liquid chromatography-mass spectroscopy analysis of the purified compound from an active extract of oil confirmed the presence of phorbol esters. Similarly, the phorbol esters content is greater in solvent extracted cake (1.1 g kg⁻¹) than in cake after being expelled (0.8 g kg⁻¹). The phytate and trypsin inhibitory activity of the cake was found to be 98 g kg⁻¹ and 8347 TIU g⁻¹ of cake, respectively. Identification of curcin was achieved by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and the concentration of curcin was 0.95 g L⁻¹ of crude concentrate obtained from cake. Higher amounts of phorbol esters are present in oil than cake but bio-diesel and glycerol are free of phorbol esters. The other anti-nutritional components such as trypsin inhibitors, phytates and curcin are present in cake, so the cake should be detoxified before being used for animal feed. Copyright © 2011 Society of Chemical Industry.

Characterization of broiler cake and broiler litter, the by-products of two management practices.

PubMed

Sistani, K R; Brink, G E; McGowen, S L; Rowe, D E; Oldham, J L

2003-10-01

The application of broiler manure and bedding (litter) on land has been a long-used disposal method that benefits plant and soil. For proper manure management, factors such as nutrient content, house cleaning management, application methods, and many land, crop, and climatic factors must be considered. A study was undertaken to characterize broiler cake and broiler litter as the by-products of two management systems in Mississippi. Broiler cake and litter productions were quantified and analyzed for four flocks during 1999 and 2000. The overall means for broiler cake production were 12.50, 13.90, and 10.30 kg m(-2) for producers 1, 2, and 3, respectively. Significantly greater quantities of litter, 27.50, 29.0, and 28.30 kg m(-2) than cake were determined for the same producers. The cake and litter moisture averaged 455 and 277 g kg(-1), respectively. No significant differences were observed between cake and litter total N, NH4-N, total C, total P, and water-soluble P (WP). However, cake had significantly greater Ca, Mg, K, Cu, Fe, Mn, and Zn than litter. Approximately 16.8% of the broiler cake and 15.2% of the broiler litter total P were in the form of water-soluble P. The NH4-N content of the cake and the litter were 12.5% and 11.5% of the cake and litter total nitrogen, respectively. The results also showed the advantage of the decaking practice with respect to the quantity of the manure generated for land application. Approximately 57% of the litter remains in the poultry house with decaking practice after each growth cycle compared to the 0% for total cleanout practice.

Effect of ingredients on rheological, physico-sensory, and nutritional characteristics of omega-3-fatty acid enriched eggless cake.

PubMed

Abhay Kumar, N; Prasada Rao, U J S; Jeyarani, T; Indrani, D

2017-10-01

The effect of defatted soya flour (DS), flax seed powder (FS) in combination (DSFS) with emulsifiers such as glycerol monostearate, GMS (DSFSG) and sodium stearoyl-2-lactylate, SSL (DSFSS) on the rheological, physico-sensory, protein subunit composition by sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE), fatty acid profile, and nutritional characteristics of eggless cake was studied. Use of DSFS, DSFSG, and DSFSS increased the amylograph peak viscosity, hot and cold paste viscosities similar to the egg. Addition of DSFS, DSFSG, and DSFSS increased viscosity of eggless cake batter; cake volume and the overall quality score (OQS) of eggless cake. Among these, highest improvement in OQS was brought about by DSFSG. According to SDS-PAGE results, the improvement by DSFSG is due to crosslinking of wheat-soya-flax proteins similar to wheat-egg proteins crosslinking. The eggless cake with DSFSG was found to be rich in omega-3-fatty acid as it contained 0.6% of linolenic acid compared to 0.1% each of cake with egg and eggless cake. As eggs are significant source of cholesterol, there has been an increased interest in search of ingredients that can replace egg in cakes. Hence, recent trend in the baking industry is to produce eggless cake using a combination of different ingredients and additives. However, there is no scientific information on the interaction of non-egg protein with wheat protein in building up the structure and also to improve the nutritional quality with respect to protein and fatty acids profiles of eggless cake. The information generated on the use of combination of defatted soya flour and flax seed along with emulsifiers will be helpful for the commercial manufacture of omega-3-fatty acid rich eggless cake with desired quality attributes. © 2017 Wiley Periodicals, Inc.

In vitro utilization of lime treated olive cake as a component of complete feed for small ruminants.

PubMed

Ishfaq, A; Sharma, R K; Rastogi, A; Malla, B A; Farooq, J

2015-01-01

The current in vitro study was carried out to determine the chemical composition and inclusion level of lime treated olive cake on acid detergent fiber (ADF) replacement basis in adult male goats. Crude olive cake was collected and evaluated for proximate composition and protein fractionation. It was treated with 6% lime and incubated for 1 week under room temperature in 2 kg sealed polythene bags and was evaluated for proximate composition after incubation. Different isonitrogenous complete diets containing 0-50% of lime treated olive cake on ADF replacement basis were formulated as per the requirement of adult male goats. In ADF replacement, fiber and concentrate sources were replaced by lime treated olive cake by replacing the 0-50% ADF percentage of the total 40% ADF value of complete feed. The formulated complete diets were tested for in vitro degradation parameters. Treatment of olive cake with 6% slaked lime increased availability of cellulose and alleviated digestibility depression caused by high ether extract percentage. Organic matter, nitrogen free extract, ADF and neutral detergent fiber were significantly lowered by lime treatment of olive cake. The cornell net carbohydrate and protein system analysis showed that non-degradable protein represented by acid detergent insoluble nitrogen (ADIN) was 21.71% whereas the non-available protein represented by neutral detergent insoluble nitrogen (NDIN) was 38.86% in crude olive cake. The in vitro dry matter degradation (IVDMD) values were comparable at all replacement levels. However, a point of inflection was observed at 40% ADF replacement level, which was supported by truly degradable organic matter (TDOM), microbial biomass production (MBP), efficiency of MBP and partitioning factor values (PF). In our study, we concluded that there is comparable difference in composition of Indian olive cake when compared with European olive cake. The most important finding was that about 78% of nitrogen present in Indian olive cake is available to animal in contrary to that of European olive cake. We concluded from in vitro studies that Indian olive cake can be included in complete feed at 30% level (w/w; 40% ADF replacement) for feeding in small ruminants without compromising in vitro degradability of the feed.

Surfactant studies for bench-scale operation

NASA Technical Reports Server (NTRS)

Hickey, Gregory S.; Sharma, Pramod K.

1992-01-01

A phase 2 study was initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This publication covers the first quarter of work. The major accomplishments were: the refurbishment of the high-pressure, high-temperature reactor autoclave, the completion of four coal liquefaction runs with Pittsburgh #8 coal, two each with and without sodium lignosulfonate surfactant, and the development of an analysis scheme for the product liquid filtrate and filter cake. Initial results at low reactor temperatures show that the addition of the surfactant produces an improvement in conversion yields and an increase in lighter boiling point fractions for the filtrate.

Determination of chlorine in silicate rocks

USGS Publications Warehouse

Peck, L.C.

1959-01-01

In a rapid accurate method for the determination of chlorine in silicate rocks, the rock powder is sintered with a sodium carbonate flux containing zinc oxide and magnesium carbonate. The sinter cake is leached with water, the resulting solution is filtered, and the filtrate is acidified with nitric acid. Chlorine is determined by titrating this solution with mercuric nitrate solution using sodium nitroprusside as the indicator. The titration is made in the dark with a beam of light shining through the solution. The end point of the titration is found by visually comparing the intensity of this beam of light with that of a similar beam of light in a reference solution.

46 CFR 148.310 - Seed cake.

Code of Federal Regulations, 2011 CFR

2011-10-01

... apply to solvent-extracted rape seed meal, pellets, soya bean meal, cotton seed meal, or sunflower seed meal that— (1) Contains a maximum of 4 percent vegetable oil and a maximum of 15 percent vegetable oil... cake. (e) The seed cake must be kept as dry as practical at all times. (f) If the seed cake is solvent...

Effect of flour-oil composite as powdered fat source in low-fat cake mixes

USDA-ARS?s Scientific Manuscript database

Excess steam jet-cooked composites containing wheat flour and 30 to 55% canola oil were drum dried and used to replace the oil and part of the flour in low-fat cake mix formulations. Specific gravity and viscosity of cake batters were measured. The cakes were analyzed for crumb grain, color, textu...

Degradation of Jatropha curcas phorbol esters derived from Jatropha oil cake and their tumor-promoting activity.

PubMed

Nakao, Motoyuki; Hasegawa, Go; Yasuhara, Tadashi; Ishihara, Yoko

2015-04-01

Large amount of oil cake is generated during biodiesel production from Jatropha seeds. Although Jatropha oil cake is rich in plant nutrients, presence of toxic phorbol esters restricts the usage of oil cake as a fertilizer. The objective of this study is to evaluate the components and tumor promoting activity of phorbol esters in Jatropha oil cake-supplemented soil and plants grown in the treated soil. Contents and their biological activity of Jatropha phorbol esters in soil and plants were sequentially analyzed by high-performance liquid chromatography (HPLC) and in vitro cell transformation assay, respectively. Disappearance of Jatropha phorbol-ester-specific peaks were followed with HPLC during incubation of Jatropha oil cake with soil for five weeks. Along with the degradation of Jatropha phorbol ester in soil, tumor-promoting activity in the sample was also attenuated and ultimately disappeared. Jatropha phorbol esters and tumor promoting activity were not detected from mustard spinach grown in the Jatropha oil cake-supplemented soil. In addition, the esterase KM109 degrades DHPB (see definition below; Jatropha phorbol ester) and reduced its tumor-promoting activity. From these data, we conclude: (1) components and tumor promoting activity of Jatropha phorbol esters in the oil cake disappeared completely by incubation with soil for five-week, (2) Jatropha phorbol esters did not transfer into plants grown in the Jatropha oil cake-supplemented soil, and (3) DHPB can be degraded by esterase from soil bacterium. These observations are useful for utilization of Jatropha oil cake as a fertilizer. Copyright © 2014 Elsevier Inc. All rights reserved.

Preservation of cocoa antioxidant activity, total polyphenols, flavan-3-ols, and procyanidin content in foods prepared with cocoa powder.

PubMed

Stahl, L; Miller, K B; Apgar, J; Sweigart, D S; Stuart, D A; McHale, N; Ou, B; Kondo, M; Hurst, W J

2009-08-01

Little is known about the effects of common cooking processes on cocoa flavanols. Antioxidant activity, total polyphenols (TP), flavanol monomers, and procyanidin oligomers were determined in chocolate frosting, a hot cocoa drink, chocolate cookies, and chocolate cake made with natural cocoa powder. Recoveries of antioxidant activity, TP, flavanol monomers, and procyanidins ranged from 86% to over 100% in the chocolate frosting, hot cocoa drink, and chocolate cookies. Losses were greatest in the chocolate cake with recoveries ranging from 5% for epicatechin to 54% for antioxidant activity. The causes of losses in baked chocolate cakes were investigated by exchanging baking soda with baking powder or combinations of the 2 leavening agents. Use of baking soda as a leavening agent was associated with increased pH and darkening color of cakes. Losses of antioxidant activity, TP, flavanol monomers, and procyanidins were associated with an increased extractable pH of the baked cakes. Chocolate cakes made with baking powder for leavening resulted in an average extractable pH of 6.2 with essentially complete retention of antioxidant activity and flavanol content, but with reduced cake heights and lighter cake color. Commercially available chocolate cake mixes had final pHs above 8.3 and contained no detectable monomeric flavanols after baking. These results suggest that baking soda causes an increase in pH and subsequent destruction of flavanol compounds and antioxidant activity. Use of an appropriate leavening agent to moderate the final cake pH to approximately 7.25 or less results in both good leavening and preservation of cocoa flavanols and procyanidins.

In vitro Starch Hydrolysis Rate, Physico-chemical Properties and Sensory Evaluation of Butter Cake Prepared Using Resistant Starch Type III Substituted for Wheat Flour.

PubMed

Pongjanta, J; Utaipattanaceep, A; Naivikul, O; Piyachomkwan, K

2008-09-01

Resistant starch type III (RS III) derived from enzymatically debranched high amylose rice starch was prepared and used to make butter cake at different levels (0, 5, 10, 15 and 20%) in place of wheat flour. Physico-chemical properties, sensory evaluation, and in vitro starch hydrolysis rate of the developed butter cake were investigated. This study showed that the content of resistant starch in butter cake increased significantly (P<0.05) as the level of substitution with RS III increased from 2.1 to 4.4% of resistant starch content. The butter cake with RS III replacement had a significantly lower in vitro starch hydrolysis rate compared to the control cake (0% RS III). The rates of starch hydrolysis from 0 to 180 min digestion time for 0, 5, 10 15, and 20% RS III in place of wheat flour in butter cakes were 3.70 to 67.65%, 2.97 to 64.86%, 2.86 to 59.99%, 2.79 to 55.96 and 2.78 to 53.04% respectively. The physico-chemical properties of 5 to 10% RS III substituted with wheat flour in the butter cake were not significantly different from the control cake and were moderately accepted by panellists in the sensory evaluation test.

Nutritionally "Empty" but "Full" of Meanings: The Socio-Cultural Significance of Birthday Cakes in Four Early Childhood Settings

ERIC Educational Resources Information Center

Albon, Deborah

2015-01-01

This article examines the socio-cultural significance of birthday cakes with the purpose of reflecting upon birthday cake practices enacted in four early childhood settings in England. I argue that birthday cakes occupy an ambiguous place in early childhood practice: seen to be both "risky"--a term I problematise--"and"…

Replacement of eggs with soybean protein isolates and polysaccharides to prepare yellow cakes suitable for vegetarians.

PubMed

Lin, Muyang; Tay, Siang Hong; Yang, Hongshun; Yang, Bao; Li, Hongliang

2017-08-15

To evaluate the feasibility of substituting eggs in yellow cake by a mixture of soybean proteins, plant polysaccharides, and emulsifiers, the batter properties, including specific gravity and viscosity; cake properties, including specific volume, texture, colour, moisture, microstructures, and structural properties of starch and glutens of the replaced cake and traditional cake containing egg, were evaluated. Replacing eggs with a soy protein isolate and 1% mono-, di-glycerides yielded a similar specific volume, specific gravity, firmness and moisture content (1.92 vs. 2.08cm 3 /g, 0.95 vs. 1.03, 319.8 vs. 376.1g, and 28.03% vs. 29.01%, respectively) compared with the traditional cakes baked with eggs. Structurally, this formulation comprised dominant gliadin aggregates in the size range of 100-200nm and glutenin networking structures containing fewer but larger porosities. The results suggest that a mixture of soybean proteins and emulsifier is a promising substitute for eggs in cakes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Using different fibers to replace fat in sponge cakes: In vitro starch digestion and physico-structural studies.

PubMed

Diez-Sánchez, Elena; Llorca, Empar; Quiles, Amparo; Hernando, Isabel

2018-01-01

This study assessed the effect of substituting 30% of fat by soluble, insoluble fiber, or a mix of both fibers in sponge cake quality, structure, acceptability, and starch digestibility. The apparent viscosity of the different formulations was measured and micro-baking was simulated. Texture profile tests were carried out and the crumb structure was examined. In vitro digestion was performed to study the digestibility of starch and a sensory test was carried out to know consumer acceptance. The soluble fiber (maltodextrin) affected the structure and quality of the cakes less than the insoluble fiber (potato fiber) and the use of soluble fiber in the formulation resulted in lower glucose release under in vitro conditions. Moreover, the consumer did not find differences among the control cake and the cakes prepared with soluble fiber. Considering the results as a whole, soluble fiber may be used for partial replacement of fat in sponge cake formulations and may constitute an appropriate strategy for obtaining healthy sponge cakes.

Effect of extruded wheat flour as a fat replacer on batter characteristics and cake quality.

PubMed

Román, Laura; Santos, Isabel; Martínez, Mario M; Gómez, Manuel

2015-12-01

The effects of three levels of fat replacement (1/3, 2/3, and 3/3) by extruded flour paste and the effects of the presence of emulsifier on layer cake batter characteristics and final cake quality were studied. Replacement of oil by extruded flour paste modified the batter density and microscopy, reducing the number of air bubbles and increasing their size, while emulsifier incorporation facilitated air entrapment in batter. Emulsifier addition also increased the elastic and viscous moduli of the batter, while oil reduction resulted in a less structured batter. Emulsifier incorporation leads to good quality cakes, minimizing the negative effect of oil reduction, maintaining the volume and reducing the hardness of cakes. Furthermore, consumer acceptability of the reduced fat cakes was improved by the addition of emulsifier. Thus, the results confirmed the positive effect of partial oil substitution (up to 2/3) by extruded flour paste on the quality of reduced fat cakes when emulsifier was incorporated.

Enrichment of gluten-free cakes with lupin (Lupinus albus L.) or buckwheat (Fagopyrum esculentum M.) flours.

PubMed

Levent, Hacer; Bilgiçli, Nermin

2011-11-01

In the present study, the effect of debittered lupin flour (LF) and whole buckwheat flour (BF) on the nutritional and sensory quality of gluten-free cake was studied. LF (10, 20, 30 and 40%) and BF (5, 10, 15 and 20%) were partially replaced with corn starch and rice flour mixture (1:1 w/w) in the gluten-free cake recipe. LF increased the protein, calcium, iron, manganese, phosphorus and zinc contents of the cakes, while BF caused a significant increase (P < 0.05) especially in potassium and magnesium contents of the gluten-free cakes. According to the overall acceptability rating, it was concluded that gluten-free cake could be produced with satisfactory results by the addition of LF and BF up to 30% and 10%, respectively.

[Effects of herb cake-separated moxibustion on spleen in immunosuppressive rabbits:a morphology study].

PubMed

Tian, Yuefeng; Wu, Aihua; Wang, Jun; Shan, Zengtian

2016-10-12

To observe the influence of different methods of moxibustion on spleen morphology in cyclophosphamide-induced immunosuppressive rabbits. A total of 50 rabbits were randomly assigned into a blank group, a model group, a herbal cake-separated moxibustion group, a moxibustion group and a sham cake-separated moxibustion group, 10 rabbits in each group. Except the blank group, the rabbits in each group were treated with intraperitoneal injection of cyclophosphamide (60 mg/kg), once a day, for 7 consecutive days to establish immunosuppressive model. After the model establishment, the rabbits in the herbal cake-separated moxibustion group were treated with herbal cake-separated moxibustion at "Shenque" (CV 8), "Guanyuan" (CV 4), "Zusanli" (ST 36), "Pishu" (BL 20) and "Shenshu" (BL 23); the moxa cone was placed on the herbal cake which was made of Liuwei Dihuang decoction, three cones for each acupoint. The rabbits in the moxibustion group were treated with moxa stick moxibustion which contained equal moxa of three moxa cones. The rabbits in the sham cake-separated moxibustion group were treated with cake which was made of flour. The acupoint selection in the above three groups was identical, and the intervention was given once every other day for totally 10 times. The rabbits in the blank group and model group were immobilized for identical time without any intervention. After treatment, the rabbits were sacrificed to collect the spleen. With routine HE staining, the morphology changes of spleen were observed under microscope. In addition, the white pulp, splenic corpuscle and the counts of lymphatic cells of lymphatic sheath around the arteries were observed. Compared with the blank group, the average size of white pulp and the radius of splenic corpuscle were reduced (both P <0.01), and the lymphatic cells of lymphatic sheath around the arteries were significantly decreased in the model group ( P <0.01), but the counts of splenic nodule were increased without significant difference ( P >0.05). Compared with the model group, the averagesize of white pulp and the radius of splenic corpuscle were significantly increased in the herbal cake-separated moxibustion group and moxibustion group (all P <0.01). The lymphatic cells of lymphatic sheath around the arteries were significantly increased in the herbal cake-separated moxibustion group and sham cake-separated moxibustion group (both P <0.01). Compared with the moxibustion group, the count of lymphatic cells of lymphatic sheath around the arteries was increased in the herbal cake-separated moxibustion ( P <0.01). Compared with the sham cake-separated moxibustion group, the radius of splenic corpuscle was significant increased in the herbal cake-separated moxibustion group ( P <0.01). The improvement of herbal cake-separated moxibustion on immunologic function is superior to moxibustion and sham cake-separated moxibustion in cyclophosphamide-induced rabbits.

Application of a life cycle assessment to compare environmental performance in coal mine tailings management.

PubMed

Adiansyah, Joni Safaat; Haque, Nawshad; Rosano, Michele; Biswas, Wahidul

2017-09-01

This study compares coal mine tailings management strategies using life cycle assessment (LCA) and land-use area metrics methods. Hybrid methods (the Australian indicator set and the ReCiPe method) were used to assess the environmental impacts of tailings management strategies. Several strategies were considered: belt filter press (OPT 1), tailings paste (OPT 2), thickened tailings (OPT 3), and variations of OPT 1 using combinations of technology improvement and renewable energy sources (OPT 1A-D). Electrical energy was found to contribute more than 90% of the environmental impacts. The magnitude of land-use impacts associated with OPT 3 (thickened tailings) were 2.3 and 1.55 times higher than OPT 1 (tailings cake) and OPT 2 (tailings paste) respectively, while OPT 1B (tailings belt filter press with technology improvement and solar energy) and 1D (tailings belt press filter with technology improvement and wind energy) had the lowest ratio of environmental impact to land-use. Further analysis of an economic cost model and reuse opportunities is required to aid decision making on sustainable tailings management and industrial symbiosis. Copyright © 2017 Elsevier Ltd. All rights reserved.

Food Preparation Studies

DTIC Science & Technology

1974-11-01

delivery to the satellites. Specialty baked goods such as cakes, brownies, bars, cookies , pies, tortes, and coffee cakes will be made at the CFPF...products (cakes, rolls, brownies, pie crusts, and tortes) will be made with mixes, but cookies , bars, and coffee cakes generally will be made from...scratch. Production of baked goods requires the following specialized equipment: • Planetary mixers • Dough mixers • Sheeters • Pie machines

Development of a novel cup cake with unique properties of essential oil of betel leaf (Piper betle L.) for sustainable entrepreneurship.

PubMed

Roy, Arnab; Guha, Proshanta

2015-08-01

Betel vine (Piper betle L.) is a root climber with deep green heart shaped leaves. It belongs to the Piperaceae family. There is a huge wastage of the leaves during glut season and it can be reduced by various means including extraction of medicinal essential oil which can be considered as GRAS (generally recognized as safe) materials. Therefore, attempts were made to develop a novel cup cake by incorporating essential oil of betel leaf. The textural properties of the cakes were measured by texture analyzer instrument; whereas the organoleptic properties were adjudged by human preferences using sensory tables containing 9-point hedonic scale. Price estimation was done considering all costs and charges. Finally, all parameters of the developed cake were compared with different cup cakes available in the market for ascertaining consumer acceptability of the newly developed product in terms of quality and market price. Results revealed that the Novel cup cake developed with 0.005 % (v/w) essential oil of betel leaf occupied the 1st place among the four developed novel cup cakes. However, it occupied 4th place among the nine cup cakes in the overall preference list prepared based on the textural and organoleptic qualities, though its market price was calculated to be comparable to all the leading cupcakes available in the market. This indicates that manufacturing of novel cup cake with essential oil of betel leaf would be a profitable and self-sustaining entrepreneurship.

Changes in chemical composition and antioxidative properties of rye ginger cakes during their shelf-life.

PubMed

Zieliński, Henryk; del Castillo, Maria Dolores; Przygodzka, Małgorzata; Ciesarova, Zuzana; Kukurova, Kristina; Zielińska, Danuta

2012-12-15

Changes in chemical composition and antioxidative properties of rye ginger cakes during their shelf-life were investigated in this study. In particular, the changes in antioxidants content, antioxidative and reducing capacity, and Maillard reaction development in rye ginger cakes after long-term storage were addressed. Ginger cakes produced according to the traditional and current recipe were stored for 5 years at room temperature in a dark place. The total phenolic compounds (TPC), inositol hexaphosphate (IP6), reduced (GSH) and oxidised glutathione (GSSG) contents, antioxidant and reducing capacity and Maillard reaction products (MRPs) were determined in ginger cakes after storage and then compared to those measured after baking. After long-term storage a decrease in TPC and IP6 contents in cakes was noted. In contrast, an increase in antioxidative and reducing capacity of stored cakes was observed. Long-term storage induced formation of furosine, advanced and final Maillard reaction products and caused changes in both reduced and oxidised forms of glutathione. After long-term storage the modest changes in furosine, FAST index and browning in ginger cake formulated with dark rye flour may suggest that this product is the healthiest among others. Therefore, traditional rye ginger cakes can be considered as an example of a healthy food that is also relatively stable during long term storage as noted by the small chemical changes observed in its composition. Copyright © 2012 Elsevier Ltd. All rights reserved.

Characteristics of rapeseed oil cake using nitrogen adsorption

NASA Astrophysics Data System (ADS)

Sokołowska, Z.; Bowanko, G.; Boguta, P.; Tys, J.; Skiba, K.

2013-09-01

Adsorption of nitrogen on the rapeseed oil cake and rapeseed oil cake with wheat meal extrudates was investigated. The results are presented as adsorption-desorption isotherms. The Brunauer-Emmet and Teller equation was used to analyse the experimental sorption data. To obtain estimates of the surface area and surface fractal dimension, the sorption isotherms were analyzed using the Brunauer-Emmet and Teller and Frenkel-Halsey-Hill equations. Mesopore analysis was carried out using the Dollimore and Heal method. The properties and surface characteristic of rapeseed oil cake extrudates are related to different basic properties of particular samples and duration of the extrusion process. Extrusion conditions lead to essential differences in particular products. For all kinds of rapeseed oil cakes the amount of adsorbed nitrogen was different, but for the rapeseed oil cake extrudates a large amount of adsorbed nitrogenwas observed. The average surface area of the rapeseed oil cake extrudates was about 6.5-7.0 m2 g-1, whereas it was equal to about 4.0-6.0 m2 g-1 for rapeseed oil cake with the wheat meal extrudates. In the case of non-extruded rapeseed oil cake and wheat meal, the dominant group included ca. 2 and 5 nmpores. The values of surface fractal dimension suggested that the surface of the extrudates was more homogenous than that of the raw material. Duration of the extrusion process to 80 s resulted in a decrease in the specific surface area, surface fractal dimension, and porosity of the extrudates.

Fungi in cake production chain: Occurrence and evaluation of growth potential in different cake formulations during storage.

PubMed

Morassi, Letícia L P; Bernardi, Angélica O; Amaral, Alexandra L P M; Chaves, Rafael D; Santos, Juliana L P; Copetti, Marina V; Sant'Ana, Anderson S

2018-04-01

This study aimed to determine the prevalence and populations of fungi in cake production chain. Besides, the growth potential of twelve fungal strains in different cake formulations was evaluated. Raw materials from two different batches (n=143), chocolate cakes (n=30), orange cakes (n=20), and processing environment air samples (n=147) were analyzed. Among the raw materials, wheat flour (3.2±0.3 log CFU per g) and corn meal (3.8±0.8 log CFU per g) belonging to batch #1 showed significant higher fungal counts (p<0.05). The fungal counts in the processing environment air reached up to 2.56 log CFU per m 3 (p<0.05). The predominant fungi species in the industrialized cakes were Aspergillus flavus (28.15%), Penicillium citrinum (18.45%), Penicillium paxilli (14.56%), and Aspergillus niger (6.8%), which were also detected in the raw materials and processing environment air. Only Penicillium glabrum and Penicillium citrinum showed visible mycelium (>3mm) in the free of preservative cake formulation at 19th and 44th days of storage at 25°C, respectively. Revealing the biodiversity of fungi in ingredients, air and final products, as well as challenging final products with representative fungal strains may assist to implement effective controlling measures as well as to gather data for the development of more robust cake formulations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Color, sensory and physicochemical attributes of beef burger made using meat from young bulls fed levels of licuri cake.

PubMed

de Gouvêa, Ana Al; Oliveira, Ronaldo L; Leão, André G; Assis, Dallyson Yc; Bezerra, Leilson R; Nascimento Júnior, Nilton G; Trajano, Jaqueline S; Pereira, Elzania S

2016-08-01

Licuri cake is a biodiesel byproduct and has been tested as an alternative feed additive for use in cattle production. This study analyzed the color, sensory and chemical attributes of burger meat from bovines. Thirty-two young Nellore bulls were used, housed in individual pens and distributed in a randomized experimental design with four treatments: no addition or the addition of 7, 14 or 21% (w/w) licuri cake in the dry matter of the diet. Interactions between the licuri cake level and the physicochemical variables (P > 0.05) were observed. Additionally, an interaction was observed between the licuri cake level and the burger beef color parameter lightness index (L*) (P = 0.0305). The L* value was positively and linearly correlated with the proportion of licuri cake in the diet of young bulls. The level of inclusion of licuri cake did not affect (P > 0.05) the sensory characteristics; the variables were graded between 6 and 7, indicating good overall acceptance. Up to 21% (w/w) licuri cake can be included in the diet of young bulls without negatively impacting on beef burger quality. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

Histopathological and Reproductive Evaluation in Male Rats Fed Jatropha curcas Seed Cake with or without Alkaline Hydrolysis and Subjected to Heat Treatment.

PubMed

Teixeira Sousa Moura, Laiane; Palomaris Mariano Souza, Domenica; Mendonça, Simone; de Aquino Ribeiro, José Antônio; Fernandes Sousa, Luciano; Tony Ramos, Adriano; Maiorka, Paulo César; de Araújo, Vera Lúcia; Mayumi Maruo, Viviane

2017-01-01

Jatropha curcas cake, a by-product of biodiesel production, is rich in protein and has potential to be used in livestock feed; however, the presence of antinutritional factors and phorbol esters limits its use. Thus, this study investigated toxicological and reproductive effects in male Wistar rats after subchronic exposure to J. curcas cake subjected to detoxification procedures. Rats were divided into seven groups ( n = 10) and treated for 60 days. The control group received commercial feed, while experimental groups received a diet containing 5% J . curcas cake nonhydrolyzed or hydrolyzed with 5 M NaOH. The cakes were unwashed or washed with ethanol or water and were autoclaved at 121°C for 30 minutes. Alkaline hydrolysis combined with ethanol washing decreased the phorbol ester concentration in the cake by 98%. Histopathological findings included diffuse degeneration of the liver and edema around the pulmonary vessels in the nonhydrolyzed groups. In addition, nontreated females mated with males of nonhydrolyzed unwashed group showed a decreased number of live fetuses and an increased placental weight. There were no signs of toxicity in rats given hydrolyzed cakes washed and unwashed, indicating that alkaline hydrolysis associated with heat treatment is an efficient method for detoxification of the J. curcas cake.

Histopathological and Reproductive Evaluation in Male Rats Fed Jatropha curcas Seed Cake with or without Alkaline Hydrolysis and Subjected to Heat Treatment

PubMed Central

Palomaris Mariano Souza, Domenica; Mendonça, Simone; de Aquino Ribeiro, José Antônio; Fernandes Sousa, Luciano; Maiorka, Paulo César; Mayumi Maruo, Viviane

2017-01-01

Jatropha curcas cake, a by-product of biodiesel production, is rich in protein and has potential to be used in livestock feed; however, the presence of antinutritional factors and phorbol esters limits its use. Thus, this study investigated toxicological and reproductive effects in male Wistar rats after subchronic exposure to J. curcas cake subjected to detoxification procedures. Rats were divided into seven groups (n = 10) and treated for 60 days. The control group received commercial feed, while experimental groups received a diet containing 5% J. curcas cake nonhydrolyzed or hydrolyzed with 5 M NaOH. The cakes were unwashed or washed with ethanol or water and were autoclaved at 121°C for 30 minutes. Alkaline hydrolysis combined with ethanol washing decreased the phorbol ester concentration in the cake by 98%. Histopathological findings included diffuse degeneration of the liver and edema around the pulmonary vessels in the nonhydrolyzed groups. In addition, nontreated females mated with males of nonhydrolyzed unwashed group showed a decreased number of live fetuses and an increased placental weight. There were no signs of toxicity in rats given hydrolyzed cakes washed and unwashed, indicating that alkaline hydrolysis associated with heat treatment is an efficient method for detoxification of the J. curcas cake. PMID:28620618

In vitro starch digestion and cake quality: impact of the ratio of soluble and insoluble dietary fiber.

PubMed

Oh, Im Kyung; Bae, In Young; Lee, Hyeon Gyu

2014-02-01

The influence of the ratio of soluble dietary fiber (SDF) and insoluble dietary fiber (IDF) on the in vitro starch digestion, predicted glycemic index (pGI), and the physicochemical properties of fiber-enriched cakes were evaluated. The hydration and pasting properties were affected by the ratio of SDF and IDF. According to the increase of IDF ratio (SDF ratio reduction) in 3 g fiber-enriched cakes, slowly digestible starch (SDS) contents increased, while the rapidly digestible starch (RDS) contents decreased. The pGI values were significantly different with control in 3 g fiber-enriched cake containing more than 50% IDF contents (p<0.05). But the pGI values of 6g fiber-enriched cake samples were not significantly different by SDF and IDF ratio. With the exception of the SDF 100% cake, volume index, hardness, and color values of the fiber-enriched cakes increased according to reductions in the SDF ratio. The cakes containing 3 g of total dietary fiber (the same ratio of SDF and IDF) per serving were shown to have low pGI and acceptable quality attributes. Specially, total dietary fiber amount and IDF ratio are more effective than SDF ratio to lower the pGI value. Copyright © 2013 Elsevier B.V. All rights reserved.

Functional characterization of steam jet-cooked buckwheat flour as a fat replacer in cake-baking.

PubMed

Min, Bockki; Lee, Seung Mi; Yoo, Sang-Ho; Inglett, George E; Lee, Suyong

2010-10-01

With rising consumer awareness of obesity, the food industry has a market-driven impetus to develop low-fat or fat-free foods with acceptable taste and texture. Fancy buckwheat flour was thus subjected to steam jet-cooking and the performance of the resulting product in cake-baking was evaluated as a fat replacer. Steam jet-cooking caused structural breakdown and starch gelatinization of buckwheat flour, thus increasing its water hydration properties. In the pasting measurements, steam jet-cooked buckwheat flour exhibited high initial viscosity, while no peak viscosity was observed. Also, the suspensions of steam jet-cooked buckwheat flour exhibited shear-thinning behaviors, which were well characterized by the power law model. When shortening in cakes was replaced with steam jet-cooked buckwheat gels, the specific gravity of cake batters significantly increased, consequently affecting cake volume after baking. However, shortening replacement with steam jet-cooked buckwheat up to 20% by weight appeared to be effective in producing cakes as soft as the control without volume loss. When buckwheat flour was thermomechanically modified by steam jet-cooking, it was successfully incorporated into cake formulations for shortening up to 20% by weight, producing low-fat cakes with comparable volume and textural properties to the control. Copyright © 2010 Society of Chemical Industry.

Mycotoxin Cocktail in the Samples of Oilseed Cake from Early Maturing Cotton Varieties Associated with Cattle Feeding Problems.

PubMed

Yunus, Agha W; Sulyok, Michael; Böhm, Josef

2015-06-12

Cottonseed cake in South East Asia has been associated with health issues in ruminants in the recent years. The present study was carried out to investigate the health issues associated with cottonseed cake feeding in dairy animals in Pakistan. All the cake samples were confirmed to be from early maturing cotton varieties (maturing prior to or during Monsoon). A survey of the resource persons indicated that the feeding problems with cottonseed cake appeared after 4-5 months of post-production storage. All the cake samples had heavy bacterial counts, and contaminated with over a dozen different fungal genera. Screening for toxins revealed co-contamination with toxic levels of nearly a dozen mycotoxins including aflatoxin B1 + B2 (556 to 5574 ppb), ochratoxin A + B (47 to 2335 ppb), cyclopiazonic acid (1090 to 6706 ppb), equisetin (2226 to 12672 ppb), rubrofusarin (81 to 1125), tenuazonic acid (549 to 9882 ppb), 3-nitropropionic acid (111 to 1032 ppb), and citrinin (29 to 359 ppb). Two buffalo calves in a diagnostic feed trial also showed signs of complex toxicity. These results indicate that inappropriate processing and storage of the cake, in the typical conditions of the subcontinent, could be the main contributory factors regarding the low quality of cottonseed cake.

Industrial Application of Artificially Induced Diploid Strains of Torulaspora delbrueckii.

PubMed

Ohshima, Y; Sugaura, T; Horita, M; Sasaki, T

1987-07-01

Diploid strains of Torulaspora delbrueckii were tested for industrial application. Because the cell volume of the diploid strain was three times as large as that of the parental haploid strain, collection and subsequent dehydration to make compressed yeast cakes were greatly improved with the diploid YL3. The time required for dehydration of the diploid strain was shortened to 1/2.5 that of the parent strain under conventional conditions. Moreover, for the diploid cells frequent filter changes for dehydration were not required, which was the case with parental cells. Fermentation activity and tolerance to freeze-thawing in dough were succesfully inherited by the diploid strains. The diploid YL3 showed nearly the same activity as the diploid F31 in bread making. However, the endurance period of yeast cakes when stored at 30 degrees C without softening to lead to liquefaction was much longer in YL3 (199 h) than in F31 (132 h). This superiority was ascribed to the fact that YL3 was induced through direct diploidization and had no genetic defect on chromosomes because the wild-type strain was employed as the parent, whereas F31 was obtained through protoplast fusion from two auxotrophic mutants and carried at least two mutagenized genes that were masked by heterolallelism.

Anti-complementary activity of enzyme-treated traditional Korean rice wine (Makgeolli) hydrolysates.

PubMed

Bae, Song Hwan; Choi, Jang Won; Ra, Kyung Soo; Yu, Kwang-Won; Shin, Kwang-Soon; Park, Sung Sun; Suh, Hyung Joo

2012-06-01

Makgeolli brewed from rice contains about 150 g kg(-1) alcohol and has a fragrance as well as an acidic and sweet taste. During the brewing process, by-products such as rice bran and brewery cake are produced. At the end of fermentation the matured mash is transferred to a filter cloth and the Makgeolli is squeezed out from the cake, leaving the lees of the mash. These by-products have continued to increase every year, resulting in an ecological problem. It is therefore important to develop new uses for them. The objective of this study was to use the by-products from the brewing of Makgeolli as a valuable functional food or nutraceutical. The anti-complementary activities of crude polysaccharides isolated from Cytolase hydrolysates of Makgeolli lees at concentrations of 1000 and 500 µg mL(-1) were 84.15 and 78.70% respectively. The activity of polysaccharide krestin (PSK) was 60.00% at 1000 µg mL(-1). The active polysaccharide obtained with Cytolase comprised mainly glucose and mannose (molar ratio 1.00:0.62). Glucose- and mannose-rich crude polysaccharides were isolated from the Cytolase hydrolysate of Makgeolli lees. The polysaccharides retain anti-complementary activity to enhance the immune system as a functional food or nutraceutical. Copyright © 2011 Society of Chemical Industry.

Effect of sunflower cake supplementation on meat quality of indigenous goat genotypes of South Africa.

PubMed

Xazela, N M; Chimonyo, M; Muchenje, V; Marume, U

2012-01-01

The effect of four castrated goat genotypes and sunflower cake supplementation on goat meat quality was determined. Supplemented Boer (BOR) and Xhosa-Boer cross (XBC) goats had significantly higher (P<0.05) SLW and CDM than non-supplemented groups. The Xhosa lop-eared (XLE) and Nguni (NGN) goats had higher pH24 (P<0.05) than BOR and XBC goats. For each genotype, the sunflower cake supplemented and non-supplemented goats had similar a* values, except for the XLE goats. In the XLE goats, the a* values were lower in the sunflower cake supplemented goats. Sunflower cake supplemented BOR goats had higher L*values than their non-supplemented counterparts (P<0.05). The sunflower cake supplemented BOR and NGN goats also had higher b* values as compared to their non-supplemented counterparts. In comparison with the Boer goat, the XLE and NGN goats had lower CDM, L* and WBF values but generally had higher CL and a* values. Sunflower cake supplementation improved meat quality attributes of the goats. Copyright © 2011 Elsevier Ltd. All rights reserved.

The role and function of chlorine in the preparation of high-ratio cake flour.

PubMed

Gough, B M; Whitehouse, M E; Greenwood, C T

1978-01-01

The literature on the role of chlorine treatment of flour for use in high-ratio cake production is discussed in relation to current knowledge of cereal chemistry and cake technology. A brief perspective of the present use of chlorine in high-ratio cake flours is included. Investigations of the uptake of gaseous chlorine by flour and its distribution among and chemical action upon the major flour components (water, protein, lipid, and carbohydrate) are assessed. The physical effects of chlorination as demonstrated by experiments with batters and cakes and by physicochemical observations of flour and its fractions are also considered. The characteristics of the starch in flour appear to be critical in high-ratio cakes. Chlorine treatment modifies the gelatinization behavior of the starch granules yet does not change their gelatinization temperature not is there evidence of chemical attack upon the starch molecules. Therefore, it is suggested that chlorine effects the necessary changes in starch behavior by reacting with the noncarbohydrate surface contaminants on the granules. Alternative methods of improving high-ratio cake flours are mentioned, particularly heat-treatment processes.

Mechanically fractionated flour isolated from green bananas (M. cavendishii var. nanica) as a tool to increase the dietary fiber and phytochemical bioactivity of layer and sponge cakes.

PubMed

Segundo, Cristina; Román, Laura; Gómez, Manuel; Martínez, Mario M

2017-03-15

This article describes the effect of mechanically fractionated flours from green bananas on the nutritional, physical and sensory attributes of two types of cakes (sponge and layer). A plausible 30% replacement of banana flour in the formulation of layer cakes is demonstrated, finding only a small decline in the sensory perception. On the contrary, sponge cakes were noticeable worsened with the use of banana flours (lower specific volume, worse sensory attributes and higher hardness), which was minimized when using fine flour. Both layer and sponge cakes exhibited an enhancement of the resistant starch and dietary fiber content with the replacement of green banana flour (up to a fivefold improvement in RS performance). Moreover, sponge cakes yielded more polyphenols and antioxidant capacity with banana flours, especially with the coarse fraction. Therefore, results showed that a mechanical fractionation allowed a feasible nutritional enhancement of cakes with the use of banana flours. Copyright © 2016 Elsevier Ltd. All rights reserved.

Utilization of expeller pressed partially defatted peanut cake meal in the preparation of bakery products.

PubMed

Chavan, J K; Shinde, V S; Kadam, S S

1991-07-01

Expeller pressed partially defatted peanut cake obtained from skin-free kernels was used as graded supplements in the preparation of breads, sweet buns, cupcakes and yeast-raised doughnuts. Incorporation of cake meal lowered the specific volume and sensory properties, but improved the fresh weight, water holding capacity and protein content of the products. The products containing 10% peanut cake meal were found to be acceptable.

Nitrogen mineralization from anaerobically digested centrifuge cake and aged air-dried biosolids.

PubMed

Kumar, Kuldip; Hundal, Lakhwinder S; Cox, Albert E; Granato, Thomas

2014-09-01

This study was conducted to estimate nitrogen (N) mineralization of anaerobically digested centrifuge cake from the Stickney Water Reclamation Plant (SWRP) and Calumet Water Reclamation Plant (CWRP), lagoon-aged air-dried biosolids from the CWRP, and Milorganite at three rates of application (0, 12.5 and 25 Mg ha(-1)). The N mineralized varied among biosolids as follows: Milorganite (44%) > SWRP centrifuge cake (35%) > CWRP centrifuge cake (31%) > aged air-dried (13%). The N mineralized in the SWRP cake (32%) and CWRP aged air-dried biosolids (12%) determined from the 15N study were in agreement with the first study. The N mineralization value for centrifuge cake biosolids observed in our study is higher than the value given in the Part 503 rule and Illinois Part 391 guidelines. These results will be used to fine-tune biosolids application rate to match crop N demand without compromising yield while minimizing any adverse effect on the environment.

Numerical modelling of powder caking at REV scale by using DEM

NASA Astrophysics Data System (ADS)

Guessasma, Mohamed; Silva Tavares, Homayra; Afrassiabian, Zahra; Saleh, Khashayar

2017-06-01

This work deals with numerical simulation of powder caking process caused by capillary condensation phenomenon. Caking consists in unwanted agglomeration of powder particles. This process is often irreversible and not easy to predict. To reproduce mechanism involved by caking phenomenon we have used the Discrete Elements Method (DEM). In the present work, we mainly focus on the role of capillary condensation and subsequent liquid bridge formation within a granular medium exposed to fluctuations of ambient relative humidity. Such bridges cause an attractive force between particles, leading to the formation of a cake with intrinsic physicochemical and mechanical properties. By considering a Representative Elementary Volume (REV), the DEM is then performed by means of a MULTICOR-3D software tacking into account the properties of the cake (degree of saturation) in order to establish relationships between the microscopic parameters and the macroscopic behaviour (tensile strength).

Effect of pretreatment on purple-fleshed sweet potato flour for cake making

NASA Astrophysics Data System (ADS)

Hutasoit, M. S.; Julianti, E.; Lubis, Z.

2018-02-01

The purple-fleshed sweet-potato (PFSP) flour was produced by varying pretreatment of washed chips: dipping in 0.5 and 1.0% (w/v) citric acid solution for 30 min, dipping in 0.5 and 1.0% (w/v) citric acid solution for 30 min and followed by steam blanching for 5 min. The pretreatment effect on cake quality was investigated. The results showed that PFSP flour produced from pretreatment with dipping in 0.5% citric acid for 30 min followed by steam blanching for 5 min had higher lightness (L*) value and lower browning index, higher hedonic value of color and aroma and baking expansion. The specific volume of cake from pretreated flour, untreated flour and wheat flour were 44.87, 43.83, and 50.43cm3/g, respectively. The sensory evaluation of cake indicated that cake from pretreated PFSP flour was acceptable compare to those of cake from wheat flour.

Effect of virgin coconut meal (VCM) on the rheological, micro-structure and baking properties of cake and batter.

PubMed

Srivastava, Yashi; Semwal, Anil Dutt

2015-12-01

Virgin coconut meal (VCM) cakes were prepared by replacing refined wheat flour (maida) (5 to 20 % level) to check its effect on chemical, textural and rheological attributes of cake. The addition of VCM significantly (p ≤ 0.05) increased redness (a*), yellowness (b*) while reduced lightness (L*) of cakes. The incorporation of VCM affects the hardness, adhesiveness gumminess and chewiness of cake. The effect of flour replacement with VCM increased the viscosity of batter which leads to increase in consistency index and lower the shearthining behavior. The viscoelastic behavior of cake batter in which elastic modulus (G') and viscous modulus (G") both were decreased with the increase in percentage of VCM. The differential scanning calorimetry (DSC) analysis revealed that the onset (To), end set (Tc) and enthalpy of gelatinization (ΔH) increased with the increased level of VCM.

Nutritional and sensory quality evaluation of sponge cake prepared by incorporation of high dietary fiber containing mango (Mangifera indica var. Chokanan) pulp and peel flours.

PubMed

Aziah, A A Noor; Min, W Lee; Bhat, Rajeev

2011-09-01

Sponge cake prepared by partial substitution of wheat flour with mango pulp and mango peel flours (MPuF and MPeF, respectively) at different concentrations (control, 5%, 10%, 20% or 30%) were investigated for the physico-chemical, nutritional and organoleptic characteristics. Results showed sponge cake incorporated with MPuF and MPeF to have high dietary fiber with low fat, calorie, hydrolysis and predicted glycemic index compared with the control. Increasing the levels of MPuF and MPeF in sponge cake had significant impact on the volume, firmness and color. Sensory evaluation showed sponge cake formulated with 10% MPuF and 10% MPeF to be the most acceptable. MPeF and MPuF have high potential as fiber-rich ingredients and can be utilized in the preparation of cake and other bakery products to improve the nutritional qualities.

Carcass traits and meat quality of crossbred Boer goats fed peanut cake as a substitute for soybean meal.

PubMed

Silva, T M; de Medeiros, A N; Oliveira, R L; Gonzaga Neto, S; Queiroga, R de C R do E; Ribeiro, R D X; Leão, A G; Bezerra, L R

2016-07-01

This study aimed to determine the impact of replacing soybean meal with peanut cake in the diets of crossbred Boer goats as determined by carcass characteristics and quality and by the fatty acid profile of meat. Forty vaccinated and dewormed crossbred Boer goats were used. Goats had an average age of 5 mo and an average BW of 15.6 ± 2.7 kg. Goats were fed Tifton-85 hay and a concentrate consisting of corn bran, soybean meal, and mineral premix. Peanut cake was substituted for soybean meal at levels of 0.0, 33.33, 66.67, and 100%. Biometric and carcass morphometric measurements of crossbred Boer goats were not affected by replacing soybean meal with peanut cake in the diet. There was no influence of the replacement of soybean meal with peanut cake on weight at slaughter ( = 0.28), HCW ( = 0.26), cold carcass weight ( = 0.23), noncarcass components of weight ( = 0.71), or muscularity index values ( = 0.11). However, regression equations indicated that there would be a reduction of 18 and 11% for loin eye area and muscle:bone ratio, respectively, between the treatment without peanut cake and the treatment with total soybean meal replacement. The weights and yields of the commercial cuts were not affected ( > 0.05) by replacing soybean meal with peanut cake in the diet. Replacing soybean meal with peanut cake did not affect the pH ( = 0.79), color index ( > 0.05), and chemical composition ( > 0.05) of the meat (). However, a quadratic trend for the ash content was observed with peanut cake inclusion in the diet ( = 0.09). Peanut cake inclusion in the diet did not affect the concentrations of the sum of SFA ( = 0.29), the sum of unsaturated fatty acids (UFA; = 0.29), or the sum of PUFA ( = 0.97) or the SFA:UFA ratio ( = 0.23) in goat meat. However, there was a linear decrease ( = 0.01) in the sum of odd-chain fatty acids in the meat with increasing peanut cake in the diet. Soybean meal replacement with peanut cake did not affect the n-6:n-3 ratio ( = 0.13) or the medium-chain fatty acid ( = 0.76), long-chain fatty acid ( = 0.74), or atherogenicity index values ( = 0.60) in the meat. The sensory attributes of the longissimus lumborum did not differ with the inclusion of peanut cake in the diet as a replacement for soybean meal. These results suggest that based on carcass and meat characteristics, peanut cake can completely substitute soybean meal in the diet of crossbred Boer goats.

Measurement of broiler litter production rates and nutrient content using recycled litter.

PubMed

Coufal, C D; Chavez, C; Niemeyer, P R; Carey, J B

2006-03-01

It is important for broiler producers to know litter production rates and litter nutrient content when developing nutrient management plans. Estimation of broiler litter production varies widely in the literature due to factors such as geographical region, type of housing, size of broiler produced, and number of flocks reared on the same litter. Published data for N, P, and K content are also highly variable. In addition, few data are available regarding the rate of production, characteristics, and nutrient content of caked litter (cake). In this study, 18 consecutive flocks of broilers were reared on the same litter in experimental pens under simulated commercial conditions. The mass of litter and cake produced was measured after each flock. Samples of all litter materials were analyzed for pH, moisture, N, P, and K. Average litter and cake moisture content were 26.4 and 46.9%, respectively. Significant variation in litter and cake nutrient content was observed and can largely be attributed to ambient temperature differences. Average litter, cake, and total litter (litter plus cake) production rates were 153.3, 74.8, and 228.2 g of dry litter material per kg of live broiler weight (g/kg) per flock, respectively. Significant variation in litter production rates among flocks was also observed. Cumulative litter, cake, and total litter production rates after 18 flocks were 170.3, 78.7, and 249.0 g/kg, respectively. The data produced from this research can be used by broiler producers to estimate broiler litter and cake production and the nutrient content of these materials.

Frosting on the cake: pictures on food packaging bias serving size.

PubMed

Brand, John; Wansink, Brian; Cohen, Abby

2016-08-01

Food packaging often pictures supplementary extras, such as toppings or frosting, that are not listed on the nutritional labelling. The present study aimed to assess if these extras might exaggerate how many calories† are pictured and if they lead consumers to overserve. Four studies were conducted in the context of fifty-one different cake mixes. For these cake mixes, Study 1 compared the calories stated on the nutrition label with the calories of the cake (and frosting) pictured on the box. In Studies 2, 3 and 4, undergraduates (Studies 2 and 3) or food-service professionals (Study 4) were given one of these typical cake mix boxes, with some being told that cake frosting was not included on the nutritional labelling whereas others were provided with no additional information. They were then asked to indicate what they believed to be a reasonable serving size of cake. Settings Laboratory setting. Undergraduate students and food-service professionals. Study 1 showed that the average calories of cake and frosting pictured on the package of fifty-one different cake mixes exceed the calories on the nutritional label by 134 %. Studies 2 and 3 showed that informing consumers that the nutritional information does not include frosting reduces how much people serve. Study 4 showed that even food-service professionals overserve if not told that frosting is not included on the nutritional labelling. To be less misleading, packaging should either not depict extras in its pictures or it should more boldly and clearly state that extras are not included in calorie counts.

Long-term toxicity and carcinogenicity studies of cake made from chlorinated flour. 1. Studies in rats.

PubMed

Fisher, N; Hutchinson, J B; Berry, R; Hardy, J; Ginocchio, A V

1983-08-01

Wistar rats were fed for 104 wk on cake-based diets in which the cake, prepared from unchlorinated flour, or flour treated with 1250 or 2500 ppm chlorine, formed 79% of the diet on a 12.6% moisture basis. A fourth group was fed stock diet 41B. No differences in appearance, health, behaviour or mortalities attributable to the flour treatment were observed. Female but not male mortalities were significantly higher for cake-fed rats than for those fed diet 41B. Dose-related haematological effects were seen at various stages in cake-fed rats. Dose-related increases in plasma alanine and aspartate aminotransferases were noted at 12 months in males but not in females, for whom all the values were elevated. A dose-related diminution in blood sugar at 12 months was seen only in females. A dose-related increase in urinary aspartate aminotransferase was seen only in males. Urinary N-acetylglucosaminidase activity per mg creatinine did not differ significantly between groups. At post mortem a dose-related reduction in spleen weight was found in the females only. The lesions found were those expected in ageing rats, but were observed earlier in rats fed cake. Glomerulonephrosis affected rats fed cake more than those fed diet 41B. Cake diets promoted nephrocalcinosis, unrelated to flour treatment. Increased splenic haematopoiesis occurred in about half of the females in the cake diet groups but less frequently in males or in rats fed diet 41B. Tumours were mainly chromophobe adenomas of the pituitary, common in rats. Insulomas were seen in two males in each of the groups fed on cake made from chlorinated flour, but an earlier form of this tumour was found in all cake groups and its incidence is thus regarded as unrelated to the flour treatment. The incidence of tumours of the reticuloendothelial system was not related to flour treatment. Covalent chlorine concentrations in the perirenal fat of the cake-fed rats were correlated with treatment levels, with values of 50-912 ppm in males and 59-1174 ppm in females. Since concentrations in the lipid of the diet fed to the animals were much higher than these, accumulation of the additive was absent or negligible. The chlorine concentrations in the perirenal fat of male and female rats fed diet 41B were 62 and 72 ppm respectively.

Edible Astronomy Demonstrations

NASA Astrophysics Data System (ADS)

Lubowich, Donald A.

2007-12-01

Astronomy demonstrations with edible ingredients are an effective way to increase student interest and knowledge of astronomical concepts. This approach has been successful with all age groups from elementary school through college students - and the students remember these demonstrations after they are presented. In this poster I describe edible demonstrations I have created to simulate the expansion of the universe (using big-bang chocolate chip cookies); differentiation during the formation of the Earth and planets (using chocolate or chocolate milk with marshmallows, cereal, candy pieces or nuts); and radioactivity/radioactive dating (using popcorn). Other possible demonstrations include: plate tectonics (crackers with peanut butter and jelly); convection (miso soup or hot chocolate); mud flows on Mars (melted chocolate poured over angel food cake); formation of the Galactic disk (pizza); formation of spiral arms (coffee with cream); the curvature of Space (Pringles); constellations patterns with chocolate chips and chocolate chip cookies; planet shaped cookies; star shaped cookies with different colored frostings; coffee or chocolate milk measurement of solar radiation; Oreo cookie lunar phases. Sometimes the students eat the results of the astronomical demonstrations. These demonstrations are an effective teaching tool and can be adapted for cultural, culinary, and ethnic differences among the students.

Direct Estimate of Cocoa Powder Content in Cakes by Colorimetry and Photoacoustic Spectroscopy

NASA Astrophysics Data System (ADS)

Dóka, O.; Bicanic, D.; Kulcsár, R.

2014-12-01

Cocoa is a very important ingredient in the food industry and largely consumed worldwide. In this investigation, colorimetry and photoacoustic spectroscopy were used to directly assess the content of cocoa powder in cakes; both methods provided satisfactory results. The calibration curve was constructed using a series of home-made cakes containing varying amount of cocoa powder. Then, at a later stage, the same calibration curve was used to quantify the cocoa content of several commercially available cakes. For self-made cakes, the relationship between the PAS signal and the content of cocoa powder was linear while a quadratic dependence was obtained for the colorimetric index (brightness) and total color difference ().

Surfactant studies for bench-scale operation

NASA Technical Reports Server (NTRS)

Hickey, Gregory S.; Sharma, Pramod K.

1993-01-01

A phase 2 study has been initiated to investigate surfactant-assisted coal liquefaction, with the objective of quantifying the enhancement in liquid yields and product quality. This report covers the second quarter of work. The major accomplishments were: completion of coal liquefaction autoclave reactor runs with Illinois number 6 coal at processing temperatures of 300, 325, and 350 C, and pressures of 1800 psig; analysis of the filter cake and the filtrate obtained from the treated slurry in each run; and correlation of the coal conversions and the liquid yield quality to the surfactant concentration. An increase in coal conversions and upgrading of the liquid product quality due to surfactant addition was observed for all runs.

Optimization of a sponge cake formulation with inulin as fat replacer: structure, physicochemical, and sensory properties.

PubMed

Rodríguez-García, Julia; Puig, Ana; Salvador, Ana; Hernando, Isabel

2012-02-01

The effects of several fat replacement levels (0%, 35%, 50%, 70%, and 100%) by inulin in sponge cake microstructure and physicochemical properties were studied. Oil substitution for inulin decreased significantly (P < 0.05) batter viscosity, giving heterogeneous bubbles size distributions as it was observed by light microscopy. Using confocal laser scanning microscopy the fat was observed to be located at the bubbles' interface, enabling an optimum crumb cake structure development during baking. Cryo-SEM micrographs of cake crumbs showed a continuous matrix with embedded starch granules and coated with oil; when fat replacement levels increased, starch granules appeared as detached structures. Cakes with fat replacement up to 70% had a high crumb air cell values; they were softer and rated as acceptable by an untrained sensory panel (n = 51). So, the reformulation of a standard sponge cake recipe to obtain a new product with additional health benefits and accepted by consumers is achieved. Practical Application:  In this study, fat is replaced by inulin in cakes, which is a fiber mainly obtained from chicory roots. Sponge cake formulations with reductions in fat content up to 70% are achieved. These high-quality products can be labeled as "reduced in fat" according to U.S. FDA (2009) and EU regulations (European-Union 2006). © 2012 Institute of Food Technologists®

Secondary Aluminum Processing Waste: Salt Cake ...

EPA Pesticide Factsheets

Thirty-nine salt cake samples were collected from 10 SAP facilities across the U.S. The facilities were identified by the Aluminum Association to cover a wide range of processes. Results suggest that while the percent metal leached from the salt cake was relatively low, the leachable metal content may still pose a contamination concern and potential human and ecological exposure if uncontrollably released to the environment. As a result, salt cake should always be managed at facilities that utilize synthetic liner systems with leachate collection (the salt content of the leachate will increase the hydraulic conductivity of clay liners within a few years of installation). The mineral phase analysis showed that various species of aluminum are present in the salt cake samples with a large degree of variability. The relative abundance of various aluminum species was evaluated but it is noted that the method used is a semi-quantitative method and as a result there is a limitation for the data use. The analysis only showed a few aluminum species present in salt cake which does not exclude the presence of other crystalline species especially in light of the variability observed in the samples. Results presented in this document are of particular importance when trying to understand concerns associated with the disposal of salt cake in MSW landfills. From the end-of-life management perspective, data presented here suggest that salt cake should not be size reduce

The influence of carbohydrate-based fat replacers with and without emulsifiers on the quality characteristics of lowfat cake.

PubMed

Khalil, A H

1998-01-01

Physical and sensory characteristics of cakes prepared with either the carbohydrate-based fat replacers N-Flate, Paselli MD 10 and Litesse (0, 25, 50 and 75% of fat weight) or fat replacers plus emulsifier (mono- and diglycerides; 0 and 3% of flour weight) were studied. Specific gravity of the batter was significantly (p < or = 0.05) improved by using the carbohydrate-based fat replacers, especially at the 25 and 50% replacement levels. The combination of the emulsifier with either Paselli MD 10 or Litesse also enhanced the specific gravity. Cakes prepared with fat replacers at the 25 and 50% levels had higher volumes, specific volume and standing heights than those of the control. Cakes prepared with fat replacers at the 25, 50 and 75% levels were more compressible than the control. Cakes prepared with Paselli MD 10 had the highest volumes, specific volume, standing heights and compressibilities. Incorporation of emulsifier with fat replacers improved cake volumes, standing heights and compressibilities. Cakes prepared with fat replacers exhibited higher crust and crumb color values compared to the control. Cakes prepared with 25 or 50% fat replacers had higher mean scores for flavor, softness and eating quality than the control. Incorporation of emulsifier with fat replacers did not affect the crust color, crumb color and flavor, but significantly (p < or = 0.05) improved softness and eating quality.

Staling of cereal bran enriched cakes and the effect of an endoxylanase enzyme on the physicochemical and sensorial characteristics.

PubMed

Lebesi, Dimitra M; Tzia, Constantina

2011-08-01

The staling of cakes enriched with untreated brans and endoxylanase-treated brans was evaluated by monitoring the changes in physicochemical, thermal, and sensorial properties of cakes during 7-d storage. Oat and rice bran were treated with different levels (0, 70, and 700 ppm) of an endoxylanase enzyme and added to cakes on 30% flour weight basis. Moisture losses, water activity, crumb firmness, starch retrogradation, and sensorial characteristics were used as staling indicators. Avrami-type equations were efficiently used for modeling the starch retrogradation kinetics, while linear models most adequately described crumb firming kinetics. Cake staling induced an increase in crumb firmness and enthalpy of amylopectin retrogradation, and a decrease in crumb moisture and sensory quality and acceptability scores of cakes. Oat bran-containing cakes better maintained their characteristics compared to the ones containing rice bran along the 7-d storage. Endoxylanase treatment of brans delayed the changes naturally induced during staling in crumb moisture content, amylopectin retrogradation enthalpy, and crumb firmness in the respective cakes. Deterioration of the sensorial characteristics was slower for the cakes containing endoxylanase-treated brans, as well. The level of endoxylanase treatment did not differentiate significantly (P < 0.05) any of the staling indicators. Overall, this study demonstrated that addition of endoxylanase-treated brans can result in cakes with improved nutritional characteristics and increased shelf life. The results of the study show the potential of using enzymes to modify underutilized food sources that can be properly incorporated in baked goods, improving their nutritional value, their quality characteristics, and providing longer shelf life. The developed procedure and results can be utilized by the bakery industry to make high fiber and low cost bakery products with improved sensorial characteristics that are appealing to the consumers. © 2011 Institute of Food Technologists®

Efficacy evaluation of a commercial neem cake for control of Haematobia irritans on Nelore cattle.

PubMed

Chagas, Ana Carolina de Souza; Oliveira, Márcia Cristina de Sena; Giglioti, Rodrigo; Calura, Fernando Henrique; Ferrenzini, Jenifer; Forim, Moacir Rossi; Barros, Antonio Thadeu Medeiros de

2010-01-01

Much attention has been given to the development of botanical insecticides to provide effective natural control of cattle ectoparasites without harming animals, consumers, and environment. This study evaluated the efficacy of a commercial neem cake in controlling Haematobia irritans infestation on cattle. The study was conducted at the Embrapa Southeast Cattle Research Center (CPPSE), in São Carlos, SP, Brazil, from April to July 2008. The neem cake mixed in mineral salt in a 2% concentration was provided to 20 Nelore cows during nine weeks and had its efficacy evaluated by comparison of the infestation level against a control group. Fly infestations were recorded weekly by digital photographs of each animal from both groups and the number of flies was later counted in a computer-assisted image analyzer. Quantification of neem cake components by high-performance liquid chromatography revealed the presence of azadirachtin (421 mg.kg(-1)) and 3-tigloyl-azadirachtol (151 mg.kg(-1)) in the tested neem cake. Addition of the 2% neem cake reduced mineral salt intake in about 22%. The 2% neem cake treatment failed to reduce horn fly infestations on cattle during the 9-week study period.

Cake: a bioinformatics pipeline for the integrated analysis of somatic variants in cancer genomes

PubMed Central

Rashid, Mamunur; Robles-Espinoza, Carla Daniela; Rust, Alistair G.; Adams, David J.

2013-01-01

Summary: We have developed Cake, a bioinformatics software pipeline that integrates four publicly available somatic variant-calling algorithms to identify single nucleotide variants with higher sensitivity and accuracy than any one algorithm alone. Cake can be run on a high-performance computer cluster or used as a stand-alone application. Availabilty: Cake is open-source and is available from http://cakesomatic.sourceforge.net/ Contact: da1@sanger.ac.uk Supplementary Information: Supplementary data are available at Bioinformatics online. PMID:23803469

Neem cake: chemical composition and larvicidal activity on Asian tiger mosquito.

PubMed

Nicoletti, Marcello; Mariani, Susanna; Maccioni, Oliviero; Coccioletti, Tiziana; Murugan, Kardaray

2012-07-01

New pesticides based on natural products are urgently needed, in consideration of their environmental care and lower collateral effects. Neem oil, the main product obtained from Azadiractha indica A. Juss, commonly known as neem tree, is mainly used in medical devices, cosmetics and soaps, as well as important insecticide. Manufacturing of neem oil first includes the collection of the neem seeds as raw material used for the extraction. Neem cake is the waste by-product remaining after extraction processes. The quality of the oil, as that of the cake, strictly depends from the quality of seeds as well as from the type of extraction processes used, which strongly influences the chemical composition of the product. Currently, the different types of commercial neem cake on the market are roughly identified as oiled and deoiled cake, but several other differences can be detected. The differences are relevant and must be determined, to obtain the necessary correlation between chemical constitution and larvicidal activities. Six different batches of neem cake, marketed by several Indian and European companies, were analyzed by HPLC and HPTLC, and their fingerprints compared, obtaining information about the different compositions, focusing in particular on nortriterpenes, considered as the main active components of neem oil. Therefore, the chemical composition of each cake was connected with the biological activitiy, i.e., the effects of the extracts of the six neem cakes were tested on eggs and larvae of Aedes albopictus (Stegomyia albopicta) (Diptera: Culicidae), commonly known as Asian tiger mosquito. The results confirmed the previously reported larvicide effects of neem cake that, however, can now be related to the chemical composition, in particular with nortriterpenes, allowing in that way to discriminate between the quality of the various marketed products, as potential domestic insecticides.

Bioactive properties of faveleira (Cnidoscolus quercifolius) seeds, oil and press cake obtained during oilseed processing.

PubMed

Ribeiro, Penha Patrícia Cabral; Silva, Denise Maria de Lima E; Assis, Cristiane Fernandes de; Correia, Roberta Targino Pinto; Damasceno, Karla Suzanne Florentino da Silva Chaves

2017-01-01

To the best of our knowledge, this is the first report in the literature concerning the bioactive properties of faveleira products. This work focuses on the physicochemical evaluation of faveleira oil, as well as it investigates the bioactive properties of faveleira seeds, faveleira oil and the press cake obtained during the oilseed processing. The seeds were cold pressed and the following tests were performed: physicochemical characteristics (acidity, peroxide values, moisture and volatile matter, density and viscosity) and fatty acid profile of faveleira oil; total phenolic and flavonoid content of faveleira seed and press cake; antibacterial activity of seed, oil and press cake; and antioxidant activity (DPPH radical scavenging activity, reducing power assay, total antioxidant capacity, superoxide radical scavenging assay and oxygen radical absorbance capacity) of seed, oil and press cake. Our work demonstrated that the faveleira seed oil has low acidity (0.78 ± 0.03% oleic acid) and peroxide value (1.13 ± 0.12 mEq/1000g), associated with the relevant concentration of linoleic acid (53.56%). It was observed that important phenolics (398.89 ± 6.34 mg EAG/100 g), especially flavonoids (29.81 ± 0.71 mg RE/g) remain in the press cake, which indicates that the by-product of the faveleira oilseed production constitutes a rich residual source of bioactive compounds. No bacterial growth inhibition was detected, but all samples including faveleira seeds, press cake, oil and its fractions have potent antioxidant activities, mainly the press cake, with oxygen radical absorbance capacity of 28.39 ± 4.36 μM TE/g. Our results also show that faveleira oil has potential to be used as edible oil and the press cake should be used to contain the most antioxidants from seed.

Bioactive properties of faveleira (Cnidoscolus quercifolius) seeds, oil and press cake obtained during oilseed processing

PubMed Central

Silva, Denise Maria de Lima e; de Assis, Cristiane Fernandes; Correia, Roberta Targino Pinto; Damasceno, Karla Suzanne Florentino da Silva Chaves

2017-01-01

To the best of our knowledge, this is the first report in the literature concerning the bioactive properties of faveleira products. This work focuses on the physicochemical evaluation of faveleira oil, as well as it investigates the bioactive properties of faveleira seeds, faveleira oil and the press cake obtained during the oilseed processing. The seeds were cold pressed and the following tests were performed: physicochemical characteristics (acidity, peroxide values, moisture and volatile matter, density and viscosity) and fatty acid profile of faveleira oil; total phenolic and flavonoid content of faveleira seed and press cake; antibacterial activity of seed, oil and press cake; and antioxidant activity (DPPH radical scavenging activity, reducing power assay, total antioxidant capacity, superoxide radical scavenging assay and oxygen radical absorbance capacity) of seed, oil and press cake. Our work demonstrated that the faveleira seed oil has low acidity (0.78 ± 0.03% oleic acid) and peroxide value (1.13 ± 0.12 mEq/1000g), associated with the relevant concentration of linoleic acid (53.56%). It was observed that important phenolics (398.89 ± 6.34 mg EAG/100 g), especially flavonoids (29.81 ± 0.71 mg RE/g) remain in the press cake, which indicates that the by-product of the faveleira oilseed production constitutes a rich residual source of bioactive compounds. No bacterial growth inhibition was detected, but all samples including faveleira seeds, press cake, oil and its fractions have potent antioxidant activities, mainly the press cake, with oxygen radical absorbance capacity of 28.39 ± 4.36 μM TE/g. Our results also show that faveleira oil has potential to be used as edible oil and the press cake should be used to contain the most antioxidants from seed. PMID:28846740

Post-anaerobic digestion thermal hydrolysis of sewage sludge and food waste: Effect on methane yields, dewaterability and solids reduction.

PubMed

Svensson, Kine; Kjørlaug, Oda; Higgins, Matthew J; Linjordet, Roar; Horn, Svein J

2018-04-01

Post-anaerobic digestion (PAD) treatment technologies have been suggested for anaerobic digestion (AD) to improve process efficiency and assure hygenization of organic waste. Because AD reduces the amount of organic waste, PAD can be applied to a much smaller volume of waste compared to pre-digestion treatment, thereby improving efficiency. In this study, dewatered digestate cakes from two different AD plants were thermally hydrolyzed and dewatered, and the liquid fraction was recirculated to a semi-continuous AD reactor. The thermal hydrolysis was more efficient in relation to methane yields and extent of dewaterability for the cake from a plant treating waste activated sludge, than the cake from a plant treating source separated food waste (SSFW). Temperatures above 165 °C yielded the best results. Post-treatment improved volumetric methane yields by 7% and the COD-reduction increased from 68% to 74% in a mesophilic (37 °C) semi-continuous system despite lowering the solid retention time (from 17 to 14 days) compared to a conventional system with pre-treatment of feed substrates at 70 °C. Results from thermogravimetric analysis showed an expected increase in maximum TS content of dewatered digestate cake from 34% up to 46% for the SSFW digestate cake, and from 17% up to 43% in the sludge digestate cake, after the PAD thermal hydrolysis process (PAD-THP). The increased dewatering alone accounts for a reduction in wet mass of cake leaving the plant of 60% in the case of sludge digestate cake. Additionaly, the increased VS-reduction will contribute to further reduce the mass of wet cake. Copyright © 2018 Elsevier Ltd. All rights reserved.

Particularies of recultivation of bore muds on oil-gas fields of Tyumen region

NASA Astrophysics Data System (ADS)

Petuhova, V. S.; Skipin, L. N.; Skipin, D. L.; Gaevaya, E. V.

2017-10-01

The article reflects negative physical and chemical properties of the bore muds in respect to Tyumen region (high dispersion, swelling ability, ash structure, crust formation, low filterability, a high degree of salinization, alkalinity and toxicity). Indicated properties are mainly stipulated by the increased content of exchangeable sodium in the absorbing complex and by the presence of soda in aqueous solution. The source of absorbed sodium and soda in water extract is the use of caustic soda in the drilling mixture. It was found out that these negative properties are illuminated using coagulant in a form of phosphogypsum - waste of chemical industry. Necessity in the nitrogen for the bean cultures-phytomeliorants is provided at the expense of legume bacteria in a form of the rizotorphin formulation. It is worth noting that growing of legume bacteria in extremely salted breeding ground on the leguminous agar has allowed choosing the most salt resistant species among the numerous strains of Melilotus officinalis and medicago. The presence of phosphorus in phosphogypsum positively influences the productivity of leguminous crops in the beginning of recultivation.

Solid-State Fermentation Reduces Phytic Acid Level, Improves the Profile of Myo-Inositol Phosphates and Enhances the Availability of Selected Minerals in Flaxseed Oil Cake

PubMed Central

2017-01-01

Summary Flaxseed oil cake was subjected to fermentation with Rhizopus oligosporus (DSM 1964 and ATCC 64063), and the phytate (InsP6) content, myo-inositol phosphate profile and in vitro bioavailability of essential minerals were studied. Flaxseed oil cake had a phytate mass fraction of 13.9 mg/g. A 96-hour fermentation of flaxseed oil cake by R. oligosporus DSM 1964 and R. oligosporus ATCC 64063 decreased the InsP6 content by 48 and 33%, respectively. The strains had different phytate-degrading activities: fermentation of flaxseed oil cake with R. oligosporus DSM 1964 was more advantageous, yielding InsP3-5 as a predominating myo-inositol compound, while fermentation with R. oligosporus ATCC 64603 produced predominantly InsP5-6. Solid-state fermentation of flaxseed oil cake enhanced in vitro bioavailability of calcium by 14, magnesium by 3.3 and phosphorus by 2–4%. PMID:29089855

Membrane fouling in a submerged membrane bioreactor with focus on surface properties and interactions of cake sludge and bulk sludge.

PubMed

Yu, Haiying; Lin, Hongjun; Zhang, Meijia; Hong, Huachang; He, Yiming; Wang, Fangyuan; Zhao, Leihong

2014-10-01

In this study, the fouling behaviors and surface properties of cake sludge and bulk sludge in a submerged membrane bioreactor (MBR) were investigated and compared. It was found that the specific filtration resistance (SFR) of cake sludge was about 5 times higher than that of bulk sludge. Two types of sludge possessed similar extracellular polymeric substances (EPS) content, particle size distribution (PSD) and zeta potential. However, their surface properties in terms of surface tensions were significantly different. Further analysis showed that cake sludge was more hydrophilic and had worse aggregation ability. Moreover, cake sludge surface possessed more hydrocarbon, less oxygen and nitrogen moieties than bulk sludge surface. It was suggested that, rather than EPS and PSD differences, the differences in the surface composition were the main cause of the great differences in SFR and adhesion ability between cake sludge and bulk sludge. Copyright © 2014 Elsevier Ltd. All rights reserved.

Designing a Clean Label Sponge Cake with Reduced Fat Content.

PubMed

Eslava-Zomeño, Cristina; Quiles, Amparo; Hernando, Isabel

2016-10-01

The fat in a sponge cake formulation was partially replaced (0%, 30%, 50%, and 70%) with OptiSol™5300.This natural functional ingredient derived from flax seeds, rich in fiber and alpha-linoleic acid, provides a natural substitute for guar and xanthan gums, avoiding E-numbers on labels. The structure and some physicochemical properties of the formulations were examined, sensory analysis was conducted and changes in starch digestibility due to adding this ingredient were determined. Increasing quantities of OptiSol™5300 gave harder cakes, with less weight loss during baking, without affecting the final cake height. There were no significant differences (P > 0.05) in texture, flavor and overall acceptance between the control and the 30% substitution cake, nor in the rapidly digestible starch values. Consequently, replacing up to 30% of the fat with OptiSol™5300 gives a new product with health benefits and a clean label that resembles the full-fat sponge cake. © 2016 Institute of Food Technologists®.

Effect of replacing ground corn and soybean meal with licuri cake on the performance, digestibility, nitrogen metabolism and ingestive behavior in lactating dairy cows.

PubMed

Ferreira, A C; Vieira, J F; Barbosa, A M; Silva, T M; Bezerra, L R; Nascimento, N G; de Freitas, J E; Jaeger, S M P L; Oliveira, P de A; Oliveira, R L

2017-11-01

Licuri (Syagrus coronate) cake is a biodiesel by-product used in ruminant feed as a beneficial energy source for supplementation in managed pastures. The objective was to evaluate the performance, digestibility, nitrogen balance, blood metabolites, ingestive behavior and diet profitability of eight crossbred Holstein (3/4)×Gyr (5/8) multiparous cows (480±25 kg BW and 100 days milking) grazing and supplemented with licuri cake partially replacing ground corn and soybean meal in concentrate (0, 200, 400 and 600 g/kg in dry matter (DM)), distributed in an experimental duplicated 4×4 Latin square design. Licuri cake partially replacing ground corn and soybean meal increased (P<0.01) the intake and digestibility of ether extract and decreased the non-fiber carbohydrates; however, there were no influences on the intakes of DM, CP, NDF and total digestible nutrients (TDN). The digestibilities of DM, CP and NDF were not influenced by licuri cake addition. There was a decrease trend on TDN digestibility (P=0.08). Licuri cake replacing ground corn and soybean meal in concentrate did not affect the intake; fecal, urinary and mammary excretions; N balance; and triglycerides concentrations. However, the blood urea nitrogen (P=0.04) concentration decreased with the licuri cakes inclusion in cow supplementation. There was an increasing trend for serum creatinine (P=0.07). Licuri cake inclusion did not affect body condition score, production, yield, protein, lactose, total solids and solid non-fat contents of milk and Minas frescal cheese. There was a linear decrease in average daily weight gain (g/day). The milk fat concentration and cheese fat production (P<0.1) presented a linear increase with partial replacement of ground corn and soybean meal with licuri cakes. The addition of licuri cake did not alter the time spent feeding, ruminating or idling. There was an increasing trend in NDF feeding efficiency (P=0.09). The replacing of ground corn and soybean meal with licuri cake up to 600 g/kg decreased the concentrate cost by US$0.45/cow per day. Licuri cake replacing corn and soybeans (400 g/kg) in concentrate promoted a profit of US$0.07/animal per day. Licuri cake is indicated to concentrate the supplementation of dairy cows with average productions of 10 kg/day at levels up to 400 g/kg in the concentrate supplement because it provides an additional profit of US$0.07/animal per day and increased milk and Minas frescal cheese fat without negative effects on productive parameters.

Factors causing PAC cake fouling in PAC-MF (powdered activated carbon-microfiltration) water treatment systems.

PubMed

Zhao, P; Takizawa, S; Katayama, H; Ohgaki, S

2005-01-01

Two pilot-scale powdered activated carbon-microfiltration (PAC-MF) reactors were operated using river water pretreated by a biofilter. A high permeate flux (4 m/d) was maintained in two reactors with different particle sizes of PAC. High concentration (20 g/L) in the PAC adsorption zone demonstrated 60-80% of organic removal rates. Analysis on the PAC cake fouling demonstrated that attached metal ions play more important role than organic matter attached on PAC to the increase of PAC cake resistance. Effects of factors which may cause PAC cake fouling in PAC-MF process were investigated and evaluated by batch experiments, further revealing that small particulates and metal ions in raw water impose prominent influence on the PAC cake layer formation. Fe (II) precipitates after being oxidized to Fe (III) during PAC adsorption and thus Fe(ll) colloids display more significant effect than other metal ions. At a high flux, PAC cake layer demonstrated a higher resistance with larger PAC due to association among colloids, metals and PAC particles, and easy migration of small particles in raw water into the void space in the PAC cake layer. Larger PAC possesses much more non-uniform particle size distribution and larger void space, making it easier for small colloids to migrate into the voids and for metal ions to associate with PAC particles by bridge effect, hence speeding up and intensifying the of PAC cake fouling on membrane surface.

Influence of Cassia grandis galactomannan on the properties of sponge cakes: a substitute for fat.

PubMed

Andrade, Francisca Joyce E T; de Albuquerque, Priscilla B S; de Seixas, José Roberto P C; Feitoza, George S; Barros Júnior, Wilson; Vicente, António A; Carneiro-da-Cunha, Maria das Graças

2018-04-25

Here we have proposed to evaluate potential replacers of fat in sponge cake formulations. Our investigation consisted initially of monitoring the physical-chemical changes in sponge cake batters caused by gradually replacing the vegetable fat/margarine of a control sample (standard sponge cake recipe) with galactomannan extracted from the seeds of Cassia grandis. Several samples were prepared where a 100% concentration of vegetable fat was substituted with galactomannan in different concentrations. We then compared both microscopic and macroscopic characteristics of pure fat cake batter formulations and formulations with controlled fat/galactomannan mixtures. At this first stage, rheometry and optical microscopy were employed to characterize the rheological features and air bubble distribution in the batters. In the second stage, the effects of fat substitution with galactomannan, now for the final baked cakes, were also monitored. Scanning electron microscopy (SEM) and standard sensorial tests were performed in order to correlate the final color, texture, and taste characteristics of the final sponge cake and those characteristics obtained initially for the batter. According to the statistical analysis of the data, a 75% fat replacement with galactomannan at only 1.0% concentration was achieved, while successfully maintaining surface microstructure, sensory acceptance, and rheological behavior similar to the original formulation containing only fat. Regarding vegetable fat substitution with galactomannan, our results allow us to conclude that rheometry and bubble distribution tests on the initial batters are useful indicators of the final cake quality.

[Poisoning by enterotoxin from Staphylococcus aureus associated with mocha pastry. Microbiology and epidemiology].

PubMed

Escartín, E F; Saldaña-Lozano, J; Montiel-Falcón, A

1998-01-01

A brief description of a foodborne outbreak due to S. aureus enterotoxin associated with the consumption of mocha cake in the city of Guadalajara is presented. The cake was prepared in a bakery and affected nearly 100 persons. S. aureus was isolated from the nose and skin of one of the pastry cooks. A S. aureus strain isolated from the cake involved in the outbreak was not only unable to grow in the mocha cream, but it actually decreased in numbers by 2 log after 72 h of storage at 30 degrees C. The pH of mocha cream ranged from 6.2 to 6.6, and water activity from 0.833 to 0.859, with a media of 0.841. In preparing mocha cake at the shop, one half of the dough used to be sprayed with a sucrose solution in water (20% w/v); mocha cream was spread on the other half of the dough before overlapping the two halves. When mocha cake was prepared in this manner, and stored at 30 degrees C, S. aureus increased in number by more than 4 log after 48 h. S. aureus did not grow in the cake stored at 4-7 degrees C. Contributory factors in this outbreak were an increase of water activity in the interphase of the mocha and the cake dough, storage of the cake in an unrefrigerated area, and an unusually high ambient temperature (28-32 degrees C) at that time.

Extraction, composition and functional properties of pennycress (Thlaspi arvense L.) press cake protein

USDA-ARS?s Scientific Manuscript database

This study compared two methods for extracting the protein in pennycress (Thlaspi arvense L.) press cake and determined the composition and functional properties of the protein products. Proteins in pennycress press cake were extracted by using the conventional alkali solubilization-acid precipitati...

Effects of feeding camelina cake to weaned pigs on safety, growth performance, and fatty acid composition of pork.

PubMed

Smit, M N; Beltranena, E

2017-06-01

Feeding cake with remaining oil contributes dietary energy (fat) in addition to protein (AA) and may provide an opportunity to enrich the n-3 fatty acid content of pork. Information regarding safety, growth performance, and efficacy of feeding camelina cake to pigs is limited. We therefore evaluated the effects of camelina cake inclusion in pig nursery diets. In total, 192 pigs (9.4 kg BW) were randomly allocated by sex to 48 pens, 2 heavy and 2 light pigs per pen. Pigs were fed 1 of 4 wheat-based diets including camelina cake (0%, 6%, 12%, or 18%; variety Celine) replacing soybean meal for 4 wk. Individual pigs, pen feed added, and orts were weighed weekly. Feces were collected on d 26 and 27. A blood sample was taken on d 29 from 24 pigs with the lowest BW/pen, which were then euthanized and necropsied. Gross pathological examination was conducted, and organ weights were measured. Samples of liver, back fat, belly fat, and jowl fat were collected for fatty acid analysis. Increasing dietary camelina cake inclusion linearly decreased ( 0.001) apparent total tract digestibility (ATTD) of DM, OM, GE and ash but did not affect ATTD of CP and P. For the entire trial (d 0 to 28), increasing camelina cake inclusion by 6% linearly decreased ( 0.001) ADFI by 74 g/d, ADG by 51 g/d, and BW by 0.8 kg but did not affect feed efficiency (G:F). Increasing camelina cake inclusion linearly increased ( 0.001) liver weight relative to BW, linearly decreased ( 0.050) kidney weight, but did not affect spleen, heart, and thyroid weights. Increasing camelina cake inclusion did not result in serological (large-animal standard panel, T3, and T4) or gross clinical (morphology) findings that might suggest toxicity. In liver, back fat, belly fat, and jowl fat, increasing dietary camelina cake inclusion linearly increased ( 0.050) total n-3 fatty acids and shorter-chain n-3 and n-6 fatty acids but did not increase docosahexaenoic acid (n-3) or arachidonic acid (n-6). In conclusion, feeding camelina cake to weaned pigs at up to 18% did not elicit clinical signs of toxicity and increased n-3 fatty acids in carcass fat depots. The decrease in ADFI as camelina cake inclusion increased resulted in pigs fed 18% weighing 5 kg less than controls at the end of the nursery period.

Radiological Monitoring of Waste Treatment Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Amin, Y. M.; Nik, H. W.

2011-03-30

Scheduled waste in West Malaysia is handled by Concession Company and is stored and then is incinerated. It is known that incineration process may result in naturally occurring radioactive materials (NORM) to be concentrated. In this study we have measured three samples consist of by-product from the operation process such as slag, filter cake and fly ash. Other various environmental media such as air, surface water, groundwater and soil within and around the plant have also been analysed for their radioactivity levels. The concentration of Ra-226, Ac-228 and K-40 in slag are 0.062 Bq/g, 0.016 Bq/g and 0.19 Bq/g respectively.more » The total activity (Ra{sub eq}) in slag is 99.5 Bq/kg. The concentration in fly ash is 0.032 Bq/g, 0.16 Bq/g and 0.34 Bq/g for Ra-226, Ac-228 and K-40 respectively resulting in Raeq of 287.0 Bq/kg. For filter cake, the concentration is 0.13 Bq/g, 0.031 Bq/g and 0.33 Bq/g for Ra-226, Ac-228 and K-40 respectively resulting in Raeq of 199.7 Bq/kg. The external radiation level ranges from 0.08 {mu}Sv/h (Administrative building) to 0.35 {mu}Sv/h (TENORM storage area). The concentration level of radon and thoron progeny varies from 0.0001 to 0.0016 WL and 0.0006 WL to 0.002 WL respectively. For soil samples, the activity ranges from 0.11 Bq/g to 0.29 Bq/g, 0.06 Bq/g to 0.18 Bq/g and 0.065 Bq/g to 0.38 Bq/g for Ra-226, Ac-228 and K-40 respectively. While activity in water, except for a trace of K-40, it is non-detectable.« less

Performance of biomorphic Silicon Carbide as particulate filter in diesel boilers.

PubMed

Orihuela, M Pilar; Gómez-Martín, Aurora; Becerra, José A; Chacartegui, Ricardo; Ramírez-Rico, Joaquín

2017-12-01

Biomorphic Silicon Carbide (bioSiC) is a novel porous ceramic material with excellent mechanical and thermal properties. Previous studies have demonstrated that it may be a good candidate for its use as particle filter media of exhaust gases at medium or high temperature. In order to determine the filtration efficiency of biomorphic Silicon Carbide, and its adequacy as substrate for diesel particulate filters, different bioSiC-samples have been tested in the flue gases of a diesel boiler. For this purpose, an experimental facility to extract a fraction of the boiler exhaust flow and filter it under controlled conditions has been designed and built. Several filter samples with different microstructures, obtained from different precursors, have been tested in this bench. The experimental campaign was focused on the measurement of the number and size of particles before and after placing the samples. Results show that the initial efficiency of filters made from natural precursors is severely determined by the cutting direction and associated microstructure. In biomorphic Silicon Carbide derived from radially cut wood, the initial efficiency of the filter is higher than 95%. Nevertheless, when the cut of the wood is axial, the efficiency depends on the pore size and the permeability, reaching in some cases values in the range 70-90%. In this case, the presence of macropores in some of the samples reduces their efficiency as particle traps. In continuous operation, the accumulation of particles within the porous media leads to the formation of a soot cake, which improves the efficiency except in the case when extra-large pores exist. For all the samples, after a few operation cycles, capture efficiency was higher than 95%. These experimental results show the potential for developing filters for diesel boilers based on biomorphic Silicon Carbide. Copyright © 2017 Elsevier Ltd. All rights reserved.

In-situ biogas sparging enhances the performance of an anaerobic membrane bioreactor (AnMBR) with mesh filter in low-strength wastewater treatment.

PubMed

Li, Na; Hu, Yi; Lu, Yong-Ze; Zeng, Raymond J; Sheng, Guo-Ping

2016-07-01

In the recent years, anaerobic membrane bioreactor (AnMBR) technology is being considered as a very attractive alternative for wastewater treatment due to the striking advantages such as upgraded effluent quality. However, fouling control is still a problem for the application of AnMBR. This study investigated the performance of an AnMBR using mesh filter as support material to treat low-strength wastewater via in-situ biogas sparging. It was found that mesh AnMBR exhibited high and stable chemical oxygen demand (COD) removal efficiencies with values of 95 ± 5 % and an average methane yield of 0.24 L CH4/g CODremoved. Variation of transmembrane pressure (TMP) during operation indicated that mesh fouling was mitigated by in-situ biogas sparging and the fouling rate was comparable to that of aerobic membrane bioreactor with mesh filter reported in previous researches. The fouling layer formed on the mesh exhibited non-uniform structure; the porosity became larger from bottom layer to top layer. Biogas sparging could not change the composition but make thinner thickness of cake layer, which might be benefit for reducing membrane fouling rate. It was also found that ultrasonic cleaning of fouled mesh was able to remove most foulants on the surface or pores. This study demonstrated that in-situ biogas sparging enhanced the performance of AnMBRs with mesh filter in low-strength wastewater treatment. Apparently, AnMBRs with mesh filter can be used as a promising and sustainable technology for wastewater treatment.

Secondary Aluminum Processing Waste: Salt Cake Characterization and Reactivity

EPA Science Inventory

Thirty-nine salt cake samples were collected from 10 SAP facilities across the U.S. The facilities were identified by the Aluminum Association to cover a wide range of processes. Results suggest that while the percent metal leached from the salt cake was relatively low, the leac...

Larvicidal activity of neem and karanja oil cakes against mosquito vectors, Culex quinquefasciatus (say), Aedes aegypti (L.) and Anopheles stephensi (L.).

PubMed

Shanmugasundaram, R; Jeyalakshmi, T; Dutt, M Sunil; Murthy, P Balakrishna

2008-01-01

Larvicidal effect of neem (Azadirachta indica) and karanja (Pongamia glabra) oil cakes (individuals and combination) was studied against mosquito species. Both the oil cakes showed larvicidal activity against the mosquito species tested. The combination of neem and karanja oil cakes in equal proportion proved to have better effect than the individual treatments. The combination of the two oil cakes recorded an LC95 of 0.93, 0.54 and 0.77% against the mosquitoes, Culex quinquefasciatus, Aedes aegypti and Anopheles stephensi respectively The increase in efficacy of the combination treatment over individuals in all the mosquito larvae tested was found to range about 4 to 10 fold in terms of LC50 and 2 to 6 fold in terms of LC95.

Detoxification of Jatropha curcas kernel cake by a novel Streptomyces fimicarius strain.

PubMed

Wang, Xing-Hong; Ou, Lingcheng; Fu, Liang-Liang; Zheng, Shui; Lou, Ji-Dong; Gomes-Laranjo, José; Li, Jiao; Zhang, Changhe

2013-09-15

A huge amount of kernel cake, which contains a variety of toxins including phorbol esters (tumor promoters), is projected to be generated yearly in the near future by the Jatropha biodiesel industry. We showed that the kernel cake strongly inhibited plant seed germination and root growth and was highly toxic to carp fingerlings, even though phorbol esters were undetectable by HPLC. Therefore it must be detoxified before disposal to the environment. A mathematic model was established to estimate the general toxicity of the kernel cake by determining the survival time of carp fingerling. A new strain (Streptomyces fimicarius YUCM 310038) capable of degrading the total toxicity by more than 97% in a 9-day solid state fermentation was screened out from 578 strains including 198 known strains and 380 strains isolated from air and soil. The kernel cake fermented by YUCM 310038 was nontoxic to plants and carp fingerlings and significantly promoted tobacco plant growth, indicating its potential to transform the toxic kernel cake to bio-safe animal feed or organic fertilizer to remove the environmental concern and to reduce the cost of the Jatropha biodiesel industry. Microbial strain profile essential for the kernel cake detoxification was discussed. Copyright © 2013 Elsevier B.V. All rights reserved.

Importance of consumer perceptions in fiber-enriched food products. A case study with sponge cakes.

PubMed

Tarrega, Amparo; Quiles, Amparo; Morell, Pere; Fiszman, Susana; Hernando, Isabel

2017-02-22

Sponge cakes enriched with fiber from different sources (maltodextrin, wheat, apple, blackcurrant and a mixture of potato and Plantago ovata) were studied. Profiling of the different cakes was carried out, first using a check-all-that-apply (CATA) question then evaluating the consumers' likings using a hedonic scale. The consumers also completed a nutrition knowledge (NK) questionnaire that was used to classify them according to their NK level. The instrumental texture of the cakes was evaluated by the texture profile analysis (TPA) method. The consumers' response was not linked to their NK level, but it mainly depended on the importance they gave to the cakes' distinctive sensory characteristics. In general, liking increased for samples considered easy to chew, spongy, soft and sweet, and decreased for samples perceived as tasteless, dry or having a fruity or an odd flavor. The sponge cakes containing maltodextrin or wheat fiber, which mostly resembled a conventional cake, were the most liked in general. Those containing the other three fibers were rejected by part of the consumers, for being tasteless in the case of potato plus Plantago ovata fiber, for being dry and doughy in the case of apple fiber and for having an odd flavor in the case of blackcurrant fiber.

Research of a possibility of receiving sorbents for a sewage disposal from a wastage of coal preparation factory

NASA Astrophysics Data System (ADS)

Buyantuev, S. L.; Kondratenko, A. S.; Shishulkin, S. Y.; Stebenkova, Y. Y.; Khmelev, A. B.

2017-05-01

The paper presents the results of the studies of the structure and porosity of the coal cake processed by electric arc plasma. The main limiting factor in processing of coal cakes sorbents is their high water content. As a result of coal washing, the main share of water introduced into the cake falls on hard-hydrate and colloidal components. This makes impossible application of traditional processes of manufacturing from a cake of coal sorbents. Using the electric arc intensifies the processes of thermal activation of coal cakes associated with thermal shock, destruction and vapor-gas reactions occurring at the surfaces of the particles at an exposure temperature of up to 3000 °C, which increases the title product outlet (sorbent) and thereby reduces manufacturing costs and improves environmental performance. The investigation of the thermal activation zone is carried out in the plasma reactor chamber by thermal imaging method followed by mapping-and 3D-modeling of temperature fields. the most important physical and chemical properties of the sorbents from coal cake activated by plasma was studied. The obtained results showed the possibility of coal cake thermal activation by electric arc plasma to change its material composition, the appearance of porosity and associated sorption capacity applied for wastewater treatment.

Ripe Banana Flour as a Source of Antioxidants in Layer and Sponge Cakes.

PubMed

Segundo, Cristina; Román, Laura; Lobo, Manuel; Martinez, Mario M; Gómez, Manuel

2017-12-01

About one-fifth of all bananas harvested become culls that are normally disposed of improperly. However, ripe banana pulp contains significant amounts of fibre and polyphenol compounds as well as a high content of simple sugars (61.06 g/100 g), making it suitable for sucrose replacement in bakery products. This work studied the feasibility of incorporating ripe banana flour (20 and 40% of replacement) in cake formulation. Physical, nutritional and sensory attributes of sponge and layer cakes were evaluated. The inclusion of ripe banana flour generally led to an increased batter consistency that hindered cake expansion, resulting in a slightly lower specific volume and higher hardness. This effect was minimised in layer cakes where differences in volume were only evident with the higher level of replacement. The lower volume and higher hardness contributed to the decline of the acceptability observed in the sensory test. Unlike physical attributes, the banana flour inclusion significantly improved the nutritional properties of the cakes, bringing about an enhancement in dietary fibre, polyphenols and antioxidant capacity (up to a three-fold improvement in antioxidant capacity performance). Therefore, results showed that sugar replacement by ripe banana flour enhanced the nutritional properties of cakes, but attention should be paid to its inclusion level.

In vitro Fermentation, Digestion Kinetics and Methane Production of Oilseed Press Cakes from Biodiesel Production

PubMed Central

Olivares-Palma, S. M.; Meale, S. J.; Pereira, L. G. R.; Machado, F. S.; Carneiro, H.; Lopes, F. C. F.; Maurício, R. M.; Chaves, A. V.

2013-01-01

Following the extraction of oil for biodiesel production, oilseed press cakes are high in fat. As the dietary supplementation of fat is currently considered the most promising strategy of consistently depressing methanogenesis, it follows that oilseed press cakes may have a similar potential for CH4 abatement. As such, this study aimed to characterise the nutritive value of several oilseed press cakes, glycerine and soybean meal (SBM) and to examine their effects on in vitro ruminal fermentation, digestion kinetics and CH4 production. Moringa press oil seeds exhibited the greatest in sacco effective degradability (ED) of DM and CP (p<0.05). In vitro gas production (ml/g digested DM) was not affected (p = 0.70) by supplement at 48 h of incubation. In vitro DMD was increased with the supplementation of glycerine and SBM at all levels of inclusion. Moringa oilseed press cakes produced the lowest CH4 (mg/g digested DM) at 6 and 12 h of incubation (p<0.05). The findings suggest that moringa oilseed press cake at 400 g/kg DM has the greatest potential of the oilseed press cakes examined in this study, to reduce CH4 production, without adversely affecting nutrient degradability. PMID:25049890

Assessment of indoor pollutants generated from bio and synthetic fuels in selected villages of Burdwan, West Bengal.

PubMed

Mondal, N K; Bhaumik, R; Das, C R; Aditya, P; Datta, J K; Banerjee, A; Das, K

2013-09-01

The objective of the present study was to access the pollutant generated from bio-fuels like bamboo sticks, cow dung, paddy straw, carbon dust cake, gobar gas, jute stick, and mustard stick and synthetic fuel like LPG during cooking in rural villages of Burdwan, West Bengal, India and its fluctuation in living room. The average SO2 released from the fuels was found in the following order: bamboo stick > cow dung > paddy straw > carbon cake > gobar gas > jute stick > LPG > mustard stick; NO2 emission was in the following order : mustard stick > carbon dust cake > paddy straw > cow dung cake > LPG, jute stick > gobar gas > bamboo stick > and SPM was obtained in the following sequence: cow dung cake > bamboo stick > carbon dust cake > gobar gas > LPG > mustard stick > paddy straw > jute stick, respectively. The highest living room to kitchen room (L/K) ratio of SO2, NO, and SPM was found in LPG, gobar gas, jute stick respectively in 2009 and followed by bamboo stick > paddy straw > jute stick > cow dung cake, respectively in 2010. Results of this study suggest that different fuels released different amount of air pollutants, but more extensive study is needed to confirm the relationship between fuels and released air pollutants.

Physico-Chemical Characterization of Fine and Ultrafine Particles Emitted during Diesel Particulate Filter Active Regeneration of Euro5 Diesel Vehicles.

PubMed

R'Mili, Badr; Boréave, Antoinette; Meme, Aurelie; Vernoux, Philippe; Leblanc, Mickael; Noël, Ludovic; Raux, Stephane; D'Anna, Barbara

2018-03-06

Diesel particulate filters (DPFs) are commonly employed in modern passenger cars to comply with current particulate matter (PM) emission standards. DPFs requires periodic regeneration to remove the accumulated matter. During the process, high-concentration particles, in both nucleation and accumulation modes, are emitted. Here, we report new information on particle morphology and chemical composition of fine (FPs) and ultrafine particles (UFPs) measured downstream of the DPF during active regeneration of two Euro 5 passenger cars. The first vehicle was equipped with a close-coupled diesel oxidation catalyst (DOC) and noncatalyzed DPF combined with fuel borne catalyst and the second one with DOC and a catalyzed-diesel particle filter (CDPF). Differences in PM emission profiles of the two vehicles were related to different after treatment design, regeneration strategies, and vehicle characteristics and mileage. Particles in the nucleation mode consisted of ammonium bisulfate, sulfate and sulfuric acid, suggesting that the catalyst desulfation is the key process in the formation of UFPs. Larger particles and agglomerates, ranging from 90 to 600 nm, consisted of carbonaceous material (soot and soot aggregates) coated by condensable material including organics, ammonium bisulfate and sulfuric acid. Particle emission in the accumulation mode was due to the reduced filtration efficiency (soot cake oxidation) throughout the regeneration process.

Physical and Chemical Properties of Sintering Red Mud and Bayer Red Mud and the Implications for Beneficial Utilization

PubMed Central

Wang, Ping; Liu, Dong-Yan

2012-01-01

Performances of two common types of red mud, Bayer red mud and Sintering red mud, were investigated in this research. Their compositions, mechanical properties and microstructure characterization were measured through XRD, TG and SEM analysis. Their shear strength, particle size, density and hydraulic characteristics also had been performed. Huge differences between the basic mineral types of these two kinds of red mud also can be found. The comparison of compositions shows that CaCO3 content in Sintering red mud is higher, Bayer red mud has more hazardous elements such as As, Pb and Hg and both have a high concentration of radioactivity. The micro particle of Bayer red mud is finer and more disperse, but the Sintering red mud has higher shear strength. Combining the TG and hydraulic characteristics analysis, it can be shown that Bayer red mud has higher value of water content and Sintering red mud has higher hydraulic conductivity. The paper then illustrates that Sintering red mud can become the main filling material of supporting structure of red mud stocking yard. Bayer red mud has a high reuse value and also can be used as a mixing material of masonry mortar.

Feasibility study of sucrose and fat replacement using inulin and rebaudioside A in cake formulations.

PubMed

Majzoobi, Mahsa; Mohammadi, Mahshid; Mesbahi, Gholamreza; Farahnaky, Asgar

2018-02-20

Cake is a popular food around the world, however, it is considered as unhealthy due to its high fat and sucrose content. To satisfy customers' demand for a low fat and sucrose cake, in this research both sucrose and fat content of the cake were reduced by using rebaudioside A (Reb A; as a natural sucrose replacer) and inulin (as a natural fat replacer) at 0%, 25%, 50%, 75%, and 100%. The water content of different formulation was adjusted to obtain a constant batter viscosity similar to the control (3,757 cP). By reducing sucrose and fat content up to 50%, water activity increased and the cakes became more asymmetrical. However, other physical properties including baking weight loss, height, volume, crust color, and texture were similar to those of the control. Higher levels of replacement (75% and 100%) resulted in remarkable loss of different quality attributes. These samples showed higher water activity and baking loss, lower volume, harder texture, darker color, and highly asymmetrical shape. Thus, successful reduction of both fat and sucrose in cakes is possible by using inulin and Reb A at replacement levels no more than 50%. Customers' demand for healthy and yet tasty and high-quality foods is increasing around the world. Therefore, finding applicable and safe methods to produce such products is of great interest in the food manufacturing to satisfy customers. Health conscious customers avoid consumption of cakes because it contains high sucrose and fat content. Many studies have been performed to reduce either fat or sucrose content, while a few studies are available to show the reduction of both fat and sucrose in the same product. This study indicates the results of an applicable method to reduce fat and sucrose content of cakes simultaneously. Using rebaudioside A (as a natural sucrose replacer) and inulin (as a natural fat replacer) up to 50% of sucrose and fat content of cakes were reduced and the resulting cake had very similar physical properties to the control. © 2018 Wiley Periodicals, Inc.

The role of gluten in a pound cake system: A model approach based on gluten-starch blends.

PubMed

Wilderjans, Edith; Pareyt, Bram; Goesaert, Hans; Brijs, Kristof; Delcour, Jan A

2008-10-15

In order to evaluate the role of gluten in cake-making, gluten-starch (GS) blends with different ratios of gluten to starch were tested in a research pound cake formula. The viscosities of batters made from commercial GS blends in the otherwise standardised formula increased with their gluten content. High viscosities during heating provide the batters with the capacity to retain expanding air nuclei, and thereby led to desired product volumes. In line with the above, increasing gluten levels in the cake recipes led to a more extended oven spring period. Cakes with a starch content exceeding 92.5% in the GS blend suffered from substantial collapse during cooling. They had a coarse crumb with a solid gummy layer at the bottom. Image analysis showed statistical differences in numbers of cells per cm(2), cell to total area ratio and mean cell area (p<0.05). Both density and mean cell area were related to gluten level. Moreover, mean cell area and cell to total area ratio were the highest for cakes with the lowest density and highest gluten levels. Relative sodium dodecyl sulfate (SDS, 2.0%) buffer (pH 6.8) extractabilities of protein from cakes baked with the different GS blends decreased with gluten content and were strongly correlated with the intensity of collapse. Taken together, the results teach that protein gives the cakes resistance to collapse, resulting in desirable volumes and an optimal grain structure with uniform cell distribution. Copyright © 2008 Elsevier Ltd. All rights reserved.

Potentials of biodegraded cashew pomace for cake baking.

PubMed

Aderiye, B I; Igbedioh, S O; Caurie, S A

1992-04-01

The use of biodegraded cashew pomace processed into flour for cake baking was investigated. The physico-chemical changes during the submerged fermentation of the pomace and the organoleptic qualities of the composite cake were also monitored. There was an increase of about 50% in protein content of the pomace after 96 h of fermentation. However, a reduction of about 61% in the total microbial count after 24 h was due to the toxic effect of the organic acids on the microbial cells during fermentation. The cashew flour had high crude fibre (ca. 20-33%) and carbohydrate (ca. 16-47%) values. The composite cake made from a 10:90 combination of 96 h-degraded cashew flour/wheat flour respectively was the most accepted. The cake which had a specific volume of 0.53 ml/g lost 11.1% moisture when 38 g of its batter was exposed to 190 degrees C for 10 minutes. This cake had a calorie value of 293.8/100 g and may be useful in feeding diabetic patients who require low carbohydrate foods.

Effects of suspended titanium dioxide nanoparticles on cake layer formation in submerged membrane bioreactor.

PubMed

Zhou, Lijie; Zhang, Zhiqiang; Xia, Siqing; Jiang, Wei; Ye, Biao; Xu, Xiaoyin; Gu, Zaoli; Guo, Wenshan; Ngo, Huu-Hao; Meng, Xiangzhou; Fan, Jinhong; Zhao, Jianfu

2014-01-01

Effects of the suspended titanium dioxide nanoparticles (TiO2 NPs, 50 mg/L) on the cake layer formation in a submerged MBR were systematically investigated. With nanometer sizes, TiO2 NPs were found to aggravate membrane pore blocking but postpone cake layer fouling. TiO2 NPs showed obvious effects on the structure and the distribution of the organic and the inorganic compounds in cake layer. Concentrations of fatty acids and cholesterol in the cake layer increased due to the acute response of bacteria to the toxicity of TiO2 NPs. Line-analysis and dot map of energy-dispersive X-ray were also carried out. Since TiO2 NPs inhibited the interactions between the inorganic and the organic compounds, the inorganic compounds (especially SiO2) were prevented from depositing onto the membrane surface. Thus, the postponed cake layer fouling was due to the changing features of the complexes on the membrane surface caused by TiO2 NPs. Copyright © 2013 Elsevier Ltd. All rights reserved.

Improvement of physical properties of gluten-free steamed cake based on black waxy rice flour using different hydrocolloids.

PubMed

Itthivadhanapong, Pimchada; Jantathai, Srinual; Schleining, Gerhard

2016-06-01

This study aimed to compare the effects of 1 % addition of four selected hydrocolloids (xanthan, guar, hypdroxypropylmethylcellulose and carrageenan) on quality characteristics of batter and of black waxy rice steamed cake compared to a control without hydrocolloids. Dynamic frequency sweeps of the batters at 25 °C indicated that all formulations exhibited gel-like behaviour with storage moduli (G') higher than loss moduli (G″). Hydrocolloids increased the apparent viscosity and the thixotropic behaviour, depending on the type of hydrocolloids. Xanthan had the greatest effects on both moduli, whereas carrageenan had the smallest effects. During a storage period of 4 days the cakes with xanthan remained softer than control samples. The overall acceptability of cake with xanthan and guar were higher than control. This study is the first report on using black waxy rice flour as a main raw material in gluten free cake. The results of this study provided useful information for selection hydrocolloids as ingredients that can help to improve the physical properties of waxy rice steamed cake.

[Use of flour from sunflower oil cake in the biosynthesis of antigungal antibiotics].

PubMed

Sukharevich, V M; Shvetsova, N N; Prodan, S I; Malkov, M A

1977-04-01

The possibility of replacing soybean meal and corn-steep liquor by food wastes of the oilpress industry and the meal of the sunflower oil cake in particular is discussed as applied to the fermentation media for production of antifungal antibiotics, such as levorin, mycoheptin, amphotericin. The studies showed that replacement of soybean meal by sunflower oil cake meal with simultaneous increasing of the amount of carbohydrates in the medium increased the levorin levels by 60--70 per cent as compared to the media used at present. When soybean meal and corn-steep liquor were simultaneously replaced by sunflower oil cake meal in amounts of 3--4 per cent the levels of mycoheptin in the fermentation broth increased by 30--65 per cent respectively. Replacement of soybean meal and corn-steep liquor by 3 per cent of sunflow oil cake meal in the medium used presently increased the amphotericin levels by 27 percent as compared to the control. Therefore, sunflower oil cake meal is a substitute of full value for soybean meal and corn-steep liquor in the fermentation media for production of antifungal antibiotics.

Utilization of biodiesel by-products for mosquito control.

PubMed

Pant, Megha; Sharma, Satyawati; Dubey, Saurabh; Naik, Satya Narayan; Patanjali, Phool Kumar

2016-03-01

The current paper has elaborated the efficient utilization of non-edible oil seed cakes (NEOC), by-products of the bio-diesel extraction process to develop a herbal and novel mosquitocidal composition against the Aedes aegypti larvae. The composition consisted of botanical active ingredients, inerts, burning agents and preservatives; where the botanical active ingredients were karanja (Pongamia glabra) cake powder and jatropha (Jatropha curcas) cake powder, products left after the extraction of oil from karanja and jatropha seed. The percentage mortality value recorded for the combination with concentration, karanja cake powder (20%) and jatropha cake powder (20%), 1:1 was 96%. The coil formulations developed from these biodiesel by-products are of low cost, environmentally friendly and are less toxic than the synthetic active ingredients. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Investigation of dielectric properties of different cake formulations during microwave and infrared-microwave combination baking.

PubMed

Sakiyan, Ozge; Sumnu, Gulum; Sahin, Serpil; Meda, Venkatesh

2007-05-01

Dielectric properties can be used to understand the behavior of food materials during microwave processing. Dielectric properties influence the level of interaction between food and high frequency electromagnetic energy. Dielectric properties are, therefore, important in the design of foods intended for microwave preparation. In this study, it was aimed to determine the variation of dielectric properties of different cake formulations during baking in microwave and infrared-microwave combination oven. In addition, the effects of formulation and temperature on dielectric properties of cake batter were examined. Dielectric constant and loss factor of cake samples were shown to be dependent on formulation, baking time, and temperature. The increase in baking time and temperature decreased dielectric constant and loss factor of all formulations. Fat content was shown to increase dielectric constant and loss factor of cakes.

Mycoflora and mycotoxin production in oilseed cakes during farm storage.

PubMed

Lanier, Caroline; Heutte, Natacha; Richard, Estelle; Bouchart, Valerie; Lebailly, Pierre; Garon, David

2009-02-25

Agricultural activities involve the use of oilseed cakes as a source of proteins for livestock. Because the storage of oilseed cakes could induce the development of molds and the production of mycotoxins, a survey was conducted during the 5 months of farm storage. Mycoflora was studied by microscopic examinations, and the presence of Aspergillus fumigatus was confirmed by polymerase chain reaction. A multimycotoxin method was developed to quantify seven mycotoxins (aflatoxin B(1), alternariol, fumonisin B(1), gliotoxin, ochratoxin A, T-2 toxin, and zearalenone) in oilseed cakes by high-performance liquid chromatography coupled to mass spectrometry. Among 34 fungal species identified, A. fumigatus and Aspergillus repens were observed during 5 and 4 months, respectively. Gliotoxin, an immunosuppressive mycotoxin, was quantified in oilseed cakes up to 45 microg/kg, which was associated with the presence of toxigenic isolates of A. fumigatus.

Integrated pyrolucite fluidized bed-membrane hybrid process for improved iron and manganese control in drinking water.

PubMed

Dashtban Kenari, Seyedeh Laleh; Barbeau, Benoit

2017-04-15

Newly developed ceramic membrane technologies offer numerous advantages over the conventional polymeric membranes. This work proposes a new configuration, an integrated pyrolucite fluidized bed (PFB)-ceramic MF/UF hybrid process, for improved iron and manganese control in drinking water. A pilot-scale study was undertaken to evaluate the performance of this process with respect to iron and manganese control as well as membrane fouling. In addition, the fouling of commercially available ceramic membranes in conventional preoxidation-MF/UF process was compared with the hybrid process configuration. In this regard, a series of experiments were conducted under different influent water quality and operating conditions. Fouling mechanisms and reversibility were analyzed using blocking law and resistance-in-series models. The results evidenced that the flux rate and the concentration of calcium and humic acids in the feed water have a substantial impact on the filtration behavior of both membranes. The model for constant flux compressible cake formation well described the rise in transmembrane pressure. The compressibility of the filter cake substantially increased in the presence of 2 mg/L humic acids. The presence of calcium ions caused significant aggregation of manganese dioxide and humic acid which severely impacted the extent of membrane fouling. The PFB pretreatment properly alleviated membrane fouling by removing more than 75% and 95% of iron and manganese, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Tailored Recovery of Carbons from Waste Tires for Enhanced Performance as Anodes in Lithium-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naskar, Amit K; Bi,; Saha, Dipendu

2014-01-01

Morphologically tailored pyrolysis-recovered carbon black is utilized in lithium-ion batteries as a potential solution for adding value to waste tire-rubber-derived materials. Micronized tire rubber was digested in a hot oleum bath to yield a sulfonated rubber slurry that was then filtered, washed, and compressed into a solid cake. Carbon was recovered from the modified rubber cake by pyrolysis in a nitrogen atmosphere. The chemical pretreatment of rubber produced a carbon monolith with higher yield than that from the control (a fluffy tire-rubber-derived carbon black). The carbon monolith showed a very small volume fraction of pores of widths 3 4 nm,more » reduced specific surface area, and an ordered assembly of graphitic domains. Electrochemical studies on the recovered-carbon-based anode revealed an improved Li-ion battery performance with higher reversible capacity than that of commercial carbon materials. Anodes made with a sulfonated tire-rubber-derived carbon and a control tire-rubber-derived carbon, respectively, exhibited an initial coulombic efficiency of 80% and 45%, respectively. The reversible capacity of the cell with the sulfonated carbon as anode was 400 mAh/g after 100 cycles, with nearly 100% coulombic efficiency. Our success in producing higher performance carbon material from waste tire rubber for potential use in energy storage applications adds a new avenue to tire rubber recycling.« less

Feeding sunflower cake from biodiesel production to Santa Ines lambs: Physicochemical composition, fatty acid profile and sensory attributes of meat

PubMed Central

Nascimento, Thiago Vinicius Costa; Oliveira, Vinicius da Silva; Ribeiro, Rebeca Dantas Xavier

2018-01-01

The aim of this study was to determine the effect of the inclusion of sunflower cake in the diets of lambs on meat quality. Forty male, uncastrated Santa Ines lambs with an initial average body weight of 20.9 ± 0.41 kg were used in a completely randomized design with four treatments. The lambs were fed 500 g/kg hay and 500 g/kg concentrate (corn, soybean meal, urea, ammonium sulfate and sunflower cake) in their diet, and the experimental treatments were 0, 10, 20, and 30% sunflower cake inclusion (DM basis). The inclusion of sunflower cake in the diet did not affect (P > 0.05) the content of ash and protein, overall acceptance, or sensory aroma of the lamb meat. Total lipids and moisture content of the longissimus lumborum muscle increased linearly (P ≤ 0.05) with sunflower cake inclusion. The C16:0, ΣSFA, ΣMUFA:ΣSFA ratio, Δ–9 desaturase enzyme and atherogenicity index in the longissimus lumborum muscle decreased linearly (P ≤ 0.05) with sunflower cake inclusion in lamb diets, whereas a linear increase occurred (P ≤ 0.05) in C12:0, C18:0, ΣMUFA, ΣPUFA, ΣPUFA:ΣSFA and ΣPUFA:ΣMUFA ratios, Σn–6, Σn–3, desirable fatty acids, h:H index, elongase activity, and flavor, tenderness and juiciness sensory qualities in lamb meat. Among the panelists, the highest preference (35.9%) was for meat with 30% sunflower cake inclusion in the diet. Sunflower cake up to 30% of total DM can be included in the diet of Santa Ines lambs, because lipid nutritional quality and the sensory qualities of the lamb meat increase, in addition to improvement in nutraceutical compounds, such as the CLA content, and in the AI, PUFA:SFA and PUFA:MUFA ratios, desirable fatty acids content and h:H ratio, which are beneficial to the health of consumers. PMID:29304058

Increasing dietary inclusions of camelina cake fed to pigs from weaning to slaughter: Safety, growth performance, carcass traits, and n-3 enrichment of pork.

PubMed

Smit, M N; Beltranena, E

2017-07-01

Feeding cake with remaining oil content not only provides additional dietary energy but may also enrich pork with -3 fatty acids. Limited information is available on feeding camelina cake to pigs relating to feeding safety (toxicity), growth performance, and efficacy of -3 enrichment of pork. Therefore, we evaluated the effects of feeding increasing camelina cake (12.2% crude fat) inclusions in diets for nursery and grower-finisher pigs. In total, 128 pigs (9.2 kg BW) were randomly allocated by sex to 32 nursery pens for 4 wk and were then moved and combined into 16 mixed-sex grower-finisher pens. Pigs were fed 1 of 4 wheat/barley-based diets including camelina variety 'Celine' cake (0%, 6%, 12%, or 18% in the nursery phase and 0%, 5%, 10%, or 15% in the grower-finisher phase) replacing soybean meal over 5 feeding phases (d 0 to 7, d 7 to 28, d 28 to 56, d 56 to 84, and d 84 to slaughter). Individual pigs and pen feed added were weighed. On d 106, a blood sample was collected from the pig with the lowest BW per pen, which was then euthanized. A pathologist conducted a gross clinical examination, and organs were weighed. Liver, back fat, and belly and jowl fat were sampled for fatty acid analysis. Pigs were slaughtered at approximately 125 kg BW. Increasing dietary camelina cake inclusion linearly decreased ( < 0.010) ADFI, ADG, BW, and G:F over the 105-d trial. Increasing dietary camelina cake inclusion linearly increased days to slaughter ( < 0.001) and carcass lean yield ( < 0.010) and linearly decreased farm ship weight ( < 0.010), carcass weight ( < 0.001), dressing percentage ( < 0.050), and back fat thickness ( < 0.010) but did not affect loin depth and index. Increasing camelina cake inclusion linearly increased liver and pancreas weight ( < 0.050) relative to BW but did not affect heart, thyroid, or kidney weights. Increasing camelina cake inclusion did not result in gross clinical or serological findings that would indicate toxicity. Increasing dietary camelina cake inclusion linearly increased ( < 0.050) -3 fatty acids, including docosahexaenoic acid, in back fat and belly and jowl fat. In conclusion, feeding camelina cake to pigs at up to 18% in the nursery phase and 15% in the grower, developer, and finisher phases did not result in clinical signs of toxicity and enriched carcass fat depots with -3 fatty acids. The observed decrease in ADFI and, consequently, ADG as camelina cake inclusion increased resulted in pigs fed 15% reaching slaughter weight 27 d later than controls.

Effects of carrot pomace powder and a mixture of pectin and xanthan on the quality of gluten-free batter and cakes.

PubMed

Majzoobi, Mahsa; Vosooghi Poor, Zahra; Mesbahi, Gholamreza; Jamalian, Jalal; Farahnaky, Asgar

2017-12-01

Carrot pomace powder (CPP) is a valuable by-product of carrot processing containing nutrients and fiber and can be utilized for enrichment of gluten-free products. The main purpose of this study was to determine the effects of various levels of CPP (0, 10, 20, and 30%) and a mixture of hydrocolloids (HC) including pectin and xanthan (1.5% of each) on the quality of batter and gluten-free cakes. With increasing the level of CPP and inclusion of HC the viscosity of the batter increased significantly from 87 mPa s for the control to >7000 mPa s for 30%CCP + HC sample. The density of the control batter was 1.2 g/cm 3 which reduced significantly to 0.899 g/cm 3 for HC sample. The pH of the cake reduced from 7.23 to 6.78 with addition of CPP but increased slightly with inclusion of HC. The density of the cake reduced from 0.510 g/cm 3 for the control to 0.395 g/cm 3 for 20%CCP + C sample. The texture of the cakes became softer, more springy and chewable with addition of CPP, CPP + HC, and HC. The control sample had the lowest uniformity index (0.178) which improved with addition of CPP and CPP + HC and a highly uniform cake with a uniformity index of 0.045 was obtained for the 30%CCP + HC cake. Addition of CPP increased the dark color of the cakes while inclusion of HC had no effect on the appearance of the cake and color. It was concluded that inclusion of maximum 30%CCP and 20%CPP + HC promoted the quality and sensory attributes of gluten-free cakes. Although different types of gluten-free products are available in the market, most of them contain insufficient amount of fiber and nutrients. Despite popularity, gluten-free cakes are poor in fiber and nutrient contents. Therefore, improving the nutritional value of these products has received an increasing attention by the food industry. Carrot pomace powder (CPP) is an available source of fiber and nutrients and hence can be utilized for enrichment of gluten-free products. This study showed that the inclusion of up to 30% CPP or 20% CPP with a mixture of xanthan and pectin (3%, 1:1) improved the quality and sensory attributes of the cakes. Industrial implications of this study may lead to new product development and improved marketing due to the enhancement of quality, sensory attributes, and nutritional value of the products. © 2017 Wiley Periodicals, Inc.

Basic Cake Decorating Workbook.

ERIC Educational Resources Information Center

Bogdany, Mel

Included in this student workbook for basic cake decorating are the following: (1) Drawings of steps in a basic way to ice a layer cake, how to make a paper cone, various sizes of flower nails, various sizes and types of tin pastry tubes, and special rose tubes; (2) recipes for basic decorating icings (buttercream, rose paste, and royal icing);…

The Icing or the Cake?

ERIC Educational Resources Information Center

Doubet, Kristina J.; Hockett, Jessica A.

2016-01-01

In this article, authors Kristina J. Doubet and Jessica A. Hockett argue that student engagement is more than a decorative icing on a cake; it's the cake itself. They cite research that an engaged student is more likely to invest in and understand the content being taught. With this in mind, the authors detail the following four principles that…

Ascent velocity and dynamics of the Fiumicino mud eruption, Rome, Italy

NASA Astrophysics Data System (ADS)

Vona, A.; Giordano, G.; De Benedetti, A. A.; D'Ambrosio, R.; Romano, C.; Manga, M.

2015-08-01

In August 2013 drilling triggered the eruption of mud near the international airport of Fiumicino (Rome, Italy). We monitored the evolution of the eruption and collected samples for laboratory characterization of physicochemical and rheological properties. Over time, muds show a progressive dilution with water; the rheology is typical of pseudoplastic fluids, with a small yield stress that decreases as mud density decreases. The eruption, while not naturally triggered, shares several similarities with natural mud volcanoes, including mud componentry, grain-size distribution, gas discharge, and mud rheology. We use the size of large ballistic fragments ejected from the vent along with mud rheology to compute a minimum ascent velocity of the mud. Computed values are consistent with in situ measurements of gas phase velocities, confirming that the stratigraphic record of mud eruptions can be quantitatively used to infer eruption history and ascent rates and hence to assess (or reassess) mud eruption hazards.

Isoform-specific functions of Mud/NuMA mediate binucleation of Drosophila male accessory gland cells.

PubMed

Taniguchi, Kiichiro; Kokuryo, Akihiko; Imano, Takao; Minami, Ryunosuke; Nakagoshi, Hideki; Adachi-Yamada, Takashi

2014-12-20

In standard cell division, the cells undergo karyokinesis and then cytokinesis. Some cells, however, such as cardiomyocytes and hepatocytes, can produce binucleate cells by going through mitosis without cytokinesis. This cytokinesis skipping is thought to be due to the inhibition of cytokinesis machinery such as the central spindle or the contractile ring, but the mechanisms regulating it are unclear. We investigated them by characterizing the binucleation event during development of the Drosophila male accessory gland, in which all cells are binucleate. The accessory gland cells arrested the cell cycle at 50 hours after puparium formation (APF) and in the middle of the pupal stage stopped proliferating for 5 hours. They then restarted the cell cycle and at 55 hours APF entered the M-phase synchronously. At this stage, accessory gland cells binucleated by mitosis without cytokinesis. Binucleating cells displayed the standard karyokinesis progression but also showed unusual features such as a non-round shape, spindle orientation along the apico-basal axis, and poor assembly of the central spindle. Mud, a Drosophila homolog of NuMA, regulated the processes responsible for these three features, the classical isoform Mud(PBD) and the two newly characterized isoforms Mud(L) and Mud(S) regulated them differently: Mud(L) repressed cell rounding, Mud(PBD) and Mud(S) oriented the spindle along the apico-basal axis, and Mud(S) and Mud(L) repressed central spindle assembly. Importantly, overexpression of Mud(S) induced binucleation even in standard proliferating cells such as those in imaginal discs. We characterized the binucleation in the Drosophila male accessory gland and examined mechanisms that regulated unusual morphologies of binucleating cells. We demonstrated that Mud, a microtubule binding protein regulating spindle orientation, was involved in this binucleation. We suggest that atypical functions exerted by three structurally different isoforms of Mud regulate cell rounding, spindle orientation and central spindle assembly in binucleation. We also propose that Mud(S) is a key regulator triggering cytokinesis skipping in binucleation processes.

Non-edible Oil Cakes as a Novel Substrate for DPA Production and Augmenting Biocontrol Activity of Paecilomyces variotii

PubMed Central

Arora, Kalpana; Sharma, Satyawati; Krishna, Suresh B. N.; Adam, Jamila K.; Kumar, Ashwani

2017-01-01

The present study investigated the use of waste non-edible oil cakes (Jatropha, Karanja, Neem, and Mahua) as a substrate for the growth of Paecilomyces variotii and dipicolinic acid (DPA) production. Previous researches proved the efficacy of DPA in suppressing certain pathogens that are deleterious to the plants in the rhizosphere. DPA production was statistical optimized by amending non-edible oil cakes in growing media as nitrogen and sugars (Dextrose, Glucose, and Lactose) as carbon source. Plackett-Burman design (PBD), indicated that Jatropha cake, Karanja cake, and Dextrose were the most significant components (p < 0.05) of the media and were further optimized using response surface methodology (RSM). Jatropha cake, Karanja cake, and Dextrose at the concentration of 12.5, 4.5, and 10 g/l, respectively, yielded 250 mg/l of DPA, which was 2.5 fold more than that obtained from basal medium. HPLC analysis of the optimized medium (peak at retention time of 30 min) confirmed the enhanced DPA production by P. variotii. The scanning electron microscopy (SEM) images showed that optimized medium impose a stress like condition (due to less C:N ratio) for the fungus and generated more spores as compared to the basal medium in which carbon source is easily available for the mycelial growth. The antimicrobial activity of the fungal extract was tested and found to be effective even at 10−2 dilution after 72 h against two plant pathogens, Fusarium oxysporum and Verticillium dahlia. Statistical experimental design of this study and the use of non-edible oil cakes as a substrate offer an efficient and viable approach for DPA production by P. variotii. PMID:28512455

Non-edible Oil Cakes as a Novel Substrate for DPA Production and Augmenting Biocontrol Activity of Paecilomyces variotii.

PubMed

Arora, Kalpana; Sharma, Satyawati; Krishna, Suresh B N; Adam, Jamila K; Kumar, Ashwani

2017-01-01

The present study investigated the use of waste non-edible oil cakes (Jatropha, Karanja, Neem, and Mahua) as a substrate for the growth of Paecilomyces variotii and dipicolinic acid (DPA) production. Previous researches proved the efficacy of DPA in suppressing certain pathogens that are deleterious to the plants in the rhizosphere. DPA production was statistical optimized by amending non-edible oil cakes in growing media as nitrogen and sugars (Dextrose, Glucose, and Lactose) as carbon source. Plackett-Burman design (PBD), indicated that Jatropha cake, Karanja cake, and Dextrose were the most significant components ( p < 0.05) of the media and were further optimized using response surface methodology (RSM). Jatropha cake, Karanja cake, and Dextrose at the concentration of 12.5, 4.5, and 10 g/l, respectively, yielded 250 mg/l of DPA, which was 2.5 fold more than that obtained from basal medium. HPLC analysis of the optimized medium (peak at retention time of 30 min) confirmed the enhanced DPA production by P. variotii . The scanning electron microscopy (SEM) images showed that optimized medium impose a stress like condition (due to less C:N ratio) for the fungus and generated more spores as compared to the basal medium in which carbon source is easily available for the mycelial growth. The antimicrobial activity of the fungal extract was tested and found to be effective even at 10 -2 dilution after 72 h against two plant pathogens, Fusarium oxysporum and Verticillium dahlia . Statistical experimental design of this study and the use of non-edible oil cakes as a substrate offer an efficient and viable approach for DPA production by P. variotii .

Detoxification and anti-nutrients reduction of Jatropha curcas seed cake by Bacillus fermentation.

PubMed

Phengnuam, Thanyarat; Suntornsuk, Worapot

2013-02-01

Jatropha curcas seed cake is a by-product generated from oil extraction of J. curcas seed. Although it contains a high amount of protein, it has phorbol esters and anti-nutritional factors such as phytate, trypsin inhibitor, lectin and saponin. It cannot be applied directly in the food or animal feed industries. This investigation was aimed at detoxifying the toxic and anti-nutritional compounds in J. curcas seed cake by fermentation with Bacillus spp. Two GRAS (generally recognized as safe) Bacillus strains used in the study were Bacillus subtilis and Bacillus licheniformis with solid-state and submerged fermentations. Solid-state fermentation was done on 10 g of seed cake with a moisture content of 70% for 7 days, while submerged fermentation was carried out on 10 g of seed cake in 100 ml distilled water for 5 days. The fermentations were incubated at the optimum condition of each strain. After fermentation, bacterial growth, pH, toxic and anti-nutritional compounds were determined. Results showed that B. licheniformis with submerged fermentation were the most effective method to degrade toxic and anti-nutritional compounds in the seed cake. After fermentation, phorbol esters, phytate and trypsin inhibitor were reduced by 62%, 42% and 75%, respectively, while lectin could not be eliminated. The reduction of phorbol esters, phytate and trypsin inhibitor was related to esterase, phytase and protease activities, respectively. J. curcas seed cake could be mainly detoxified by bacterial fermentation and the high-protein fermented seed cake could be potentially applied to animal feed. Copyright © 2012 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Preparation of food supplements from oilseed cakes.

PubMed

Sunil, L; Appaiah, Prakruthi; Prasanth Kumar, P K; Gopala Krishna, A G

2015-05-01

Oilseed cakes have been in use for feed preparation. Being rich in proteins, antioxidants, fibers, vitamins and minerals, oilseed cakes have been considered ideal for food supplementation. These oilseed cakes can be processed and made more palatable and edible by suitable treatments and then incorporated as food supplements for human consumption. Rice bran pellets (RBP), stabilized rice bran (SRB), coconut cake (CC) and sesame cake (SC) were taken up for the study. These were mixed with distilled water and cooked in such a way to separate the cooked solid residue and liquid extract followed by freeze drying to get two products from each. The raw, cooked dried residue and extract were analyzed for various parameters such as moisture (0.9-27.4 %), fat (2.1-16.1 %), ash (3.3-9.0 %), minerals (2.6-633.2 mg/100 g), total dietary fiber (23.2-58.2 %), crude fiber (2.7-10.5 %), protein (3.2-34.0 %), and the fat further analyzed for fatty acid composition, oryzanol (138-258 mg/100 g) and lignan (99-113 mg/100 g) contents and also evaluated sensory evaluation. Nutritional composition of products as affected by cooking was studied. The cooked products (residue and extract) showed changes in nutrients content and composition from that of the starting cakes and raw materials, but retained more nutrients in cooked residue than in the extract. The sensory evaluation of cooked residue and extract showed overall higher acceptability by the panelists than the starting cakes and raw materials. On the basis of these findings it can be concluded that these cooked residue and extract products are highly valuable for food supplementation than the raw ones.

Degradation of phorbol esters by Pseudomonas aeruginosa PseA during solid-state fermentation of deoiled Jatropha curcas seed cake.

PubMed

Joshi, Chetna; Mathur, Priyanka; Khare, S K

2011-04-01

Large amount of seed cake is generated as by-product during biodiesel production from Jatropha seeds. Presence of toxic phorbol esters restricts its utilization as livestock feed. Safe disposal or meaningful utilization of this major by-product necessitates the degradation of these phorbol esters. The present study describes the complete degradation of phorbol esters by Pseudomonas aeruginosa PseA strain during solid state fermentation (SSF) of deoiled Jatropha curcas seed cake. Phorbol esters were completely degraded in nine days under the optimized SSF conditions viz. deoiled cake 5.0 g; moistened with 5.0 ml distilled water; inoculum 1.5 ml of overnight grown P. aeruginosa; incubation at temperature 30 °C, pH 7.0 and RH 65%. SSF of deoiled cake seems a potentially viable approach towards the complete degradation of the toxic phorbol esters. Copyright © 2011 Elsevier Ltd. All rights reserved.

Co-composting of physic nut (Jatropha curcas) deoiled cake with rice straw and different animal dung.

PubMed

Das, Manab; Uppal, H S; Singh, Reena; Beri, Shanuja; Mohan, K S; Gupta, Vikas C; Adholeya, Alok

2011-06-01

To address the dispensing of this growing volume, a study on utilization of jatropha (Jatropha curcas) deoiled cake through compost production was carried out. The deoiled cake was composted with rice straw, four different animal dung (cow dung, buffalo dung, horse dung and goat dung) and hen droppings in different proportions followed by assessment, and comparison of biochemical characteristics among finished composts. Nutrient content in finished compost was within the desired level whereas metals such as copper, lead and nickel were much below the maximum allowable concentrations. Although a few finished material contained phorbol ester (0.12 mg/g), but it was far below the original level found in the deoiled cake. Such a study indicates that a huge volume of jatropha deoiled cake can be eliminated through composting. Copyright © 2011 Elsevier Ltd. All rights reserved.

Prediction during language processing is a piece of cake--but only for skilled producers.

PubMed

Mani, Nivedita; Huettig, Falk

2012-08-01

Are there individual differences in children's prediction of upcoming linguistic input and what do these differences reflect? Using a variant of the preferential looking paradigm (Golinkoff, Hirsh-Pasek, Cauley, & Gordon, 1987), we found that, upon hearing a sentence like, "The boy eats a big cake," 2-year-olds fixate edible objects in a visual scene (a cake) soon after they hear the semantically constraining verb eats and prior to hearing the word cake. Importantly, children's prediction skills were significantly correlated with their productive vocabulary size-skilled producers (i.e., children with large production vocabularies) showed evidence of predicting upcoming linguistic input, while low producers did not. Furthermore, we found that children's prediction ability is tied specifically to their production skills and not to their comprehension skills. Prediction is really a piece of cake, but only for skilled producers.

Estimation of shelf life of wikau maombo brownies cake using Accelerated Shelf Life Testing (ASLT) method with Arrhenius model

NASA Astrophysics Data System (ADS)

Wahyuni, S.; Holilah; Asranudin; Noviyanti

2018-02-01

The shelf life of brownies cake made from wikau maombo flour was predicted by ASLT method through the Arrhenius model. The aim of this study was to estimate the shelf life of brownies cake made from wikau maombo flour. The storage temperature of brownies cake was carried out at 20°C, 30°C and 45°C. The results showed that TBA (Thio Barbaturic Acid) number of brownies cake decreased as the storage temperature increase. Brownies stored at 20°C and 30°C were overgrown with mold on the storage time of six days. Brownies product (WT0 and WT1) had shelf life at 40°C approximately six and fourteen days, respectively. Brownies made from wikau maombo and wheat flour (WT1) was the best product with had the longest of shelf life about fourteen days.

Pea and Broad Bean Pods as a Natural Source of Dietary Fiber: The Impact on Texture and Sensory Properties of Cake.

PubMed

Belghith-Fendri, Lilia; Chaari, Fatma; Kallel, Fatma; Zouari-Ellouzi, Soumaya; Ghorbel, Raoudha; Besbes, Souhail; Ellouz-Chaabouni, Semia; Ghribi-Aydi, Dhouha

2016-10-01

Attention has focused on bakery products such as cake which is one of the most common bakery products consumed by people in the world. Legume by-products, pea pods (PPs) (Pisum sativum L.) and broad bean pods (BBPs) (Vicia faba L.) mediterranean (Tunisian), has been studied for its high dietary fiber content (PP: 43.87 g/100 g; BBP: 53.01 g/100 g). Protein content was also a considerable component for both by-products. We investigated the effect of substituted of 5%, 10%, 15%, 20%, 25%, and 30% of PP and BBP flours on the sensory and technological properties in cake. Cakes hardness increased whereas L * and a * color values decreased. The overall acceptability rate showed that a maximum of 15% of PP and BBP flours can be added to prepare acceptable quality cakes. © 2016 Institute of Food Technologists®.

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air

PubMed Central

Hassan, Ghassan; Yilbas, B. S.; Said, Syed A. M.; Al-Aqeeli, N.; Matin, Asif

2016-01-01

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface. PMID:27445272

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air.

PubMed

Hassan, Ghassan; Yilbas, B S; Said, Syed A M; Al-Aqeeli, N; Matin, Asif

2016-07-22

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface.

Factors controlling mud accumulation in the Heuksan mud belt off southwestern Korea

NASA Astrophysics Data System (ADS)

Chang, Tae Soo; Ha, Hun Jun; Chun, Seung Soo

2015-12-01

The Heuksan mud belt (hereafter HMB) is 20~50 km wide, ~200 km long, and ~50 m thick, having accumulated in the course of the Holocene transgression on the tide-dominated epicontinental shelf southwest of Korea. The internal architecture of the HMB is characterized by offshore prograding clinoforms. Of particular interest are the depositional processes responsible for this anomalously thick mud accumulation within a relatively short period of time. Tidal currents are important in the dispersal of mud in the HMB, although these alone cannot explain such an enormous mud deposit. In order to understand the formative processes of the HMB, a detailed sedimentary facies analysis, including high-resolution grain-size measurements, has been conducted on more than 30 short cores and three long drill cores recovered from the mud belt. Five major mud facies were identified. Of these, mud sequences showing a thickening-thinning trend of alternating silt and clay laminae suggestive of a tidal origin occur dominantly at inner to mid shelf locations. By contrast, internally structureless muds with sharp bases and no bioturbation, which are interpreted of representing fluid-mud deposits, are widespread at mid to outer shelf locations. Wave-generated mud ripples and storm beds on the inner shelf suggest that storm waves in winter resuspend previously deposited mud to form near-bed fluid-mud suspensions with resulting gravity-driven mud transport across the low-gradient outer shelf. This previously not recognized process is probably a major factor controlling depositional processes on the giant mud belt, enabling rapid accumulation and offshore progradation even during transgression, i.e., at times of sea-level rise.

Stockpiling and Comprehensive Utilization of Red Mud Research Progress

PubMed Central

Liu, Dong-Yan; Wu, Chuan-Sheng

2012-01-01

With increasing production of red mud, the environmental problems caused by it are increasingly serious, and thus the integrated treatment of red mud is imminent. This article provides an overview of the composition and the basic characteristics of red mud. The research progress of safe stockpiling and comprehensive utilization of red mud is summarized. The safe stockpiling of red mud can be divided into two aspects: the design and safe operation of the stocking yard. The comprehensive utilization of red mud can be further divided into three aspects: the effective recycling of components, resource utilization and application in the field of environmental protection. This paper points out that the main focus of previous studies on red mud stockpiling is cost reproduction and land tenure. The recovery of resources from red mud has a high value-added, but low level industrialization. The use of red mud as a building material and filler material is the most effective way to reduce the stockpiling of red mud. Red mud used for environmental remediation materials is a new hotspot and worth promoting for its simple processing and low cost.

Learning Programming through Baking

ERIC Educational Resources Information Center

Moon, Cameron

2018-01-01

Baking a cake and programming have many attributes in common. Both baking and programming rely on a specific process to produce an expected outcome. A cake needs the right amount of each ingredient mixed in at the right time, the oven to be set at a specific temperature, and the cake to be baked for a specific length of time. Programs need to be…

Cake Flour Is Not Just Any Old White Powder: A Fun Take-Home Experiment

ERIC Educational Resources Information Center

McMullen, Kevin; Rasmus, C.; Virtue, Melinda; Slik, Kate; Wrigley, Colin

2014-01-01

Baking cakes with different recipes can provide an exercise in the application of the scientific method, illustrating the need to vary only one ingredient at a time for correct derivation of conclusions. This experiment, most likely to be performed at home, compares a cake flour with flours from durum wheat, rice and cornflour (gluten-free…

[Experiences with the enzymatic determination of sugar and sugar substitutes in dietetic cake for diabetics (author's transl)].

PubMed

Klingebiel, L; Grossklaus, R; Pahlke, G

1979-11-01

Sorbitol and fructose were determined enzymatically in home-made and commercially produced cake for diabetics. In some commercial products, a loss of fructose depending upon the baking period was found. This loss of fructose is to be attributed to the Maillard reaction. The findings were confirmed by comparative studies will a reference cake.

Can acceptable quality angel food cakes be made using pasteurized shell eggs? The effects of processing factors on functional properties of angel food cakes

USDA-ARS?s Scientific Manuscript database

Due to recent incidences of Salmonella contamination, the market for pasteurized shell eggs is rapidly growing. One objection to using pasteurized shell eggs is the belief that they will produce unacceptable baked product (e.g., angel food cakes). In the present study, shell eggs were pasteurized us...

Antifungal activities of ethanolic extract from Jatropha curcas seed cake.

PubMed

Saetae, Dolaporn; Suntornsuk, Worapot

2010-02-01

Phorbol ester extraction was carried out from Jatropha curcas seed cake, a by-product from the bio-diesel fuel industry. Four repeated extractions from 5 g J. curcas seed cake using 15 ml of 90% (v/v) ethanol and a shaking speed of 150 rev/min gave the highest yield of phosbol esters. The ethanolic extract of J. curcas seed cake showed antifungal activities against important phytofungal pathogens: Fusarium oxysporum, Pythium aphanidermatum, Lasiodiplodia theobromae, Curvularia lunata, Fusarium semitectum, Colletotrichum capsici and Colletotrichum gloeosporiodes. The extract contained phorbol esters mainly responsible for antifungal activities. The extract could therefore be used as an antifungal agent for agricultural applications.

Processing of commercial peanut cake into food-grade meal and its utilization in preparation of cookies.

PubMed

Tate, P V; Chavan, J K; Patil, P B; Kadam, S S

1990-04-01

The commercial cake produced during expeller pressing of peanuts was extracted with n-hexane, and 80% ethanol followed by sieving through 80 mesh, to remove residual oil, pigments, bitter taste and fibrous material. The processed meal exhibited comparable composition with defatted peanut flour prepared in the laboratory by solvent extraction of full-fat peanut meal. However, the processed cake meal exhibited low methionine content and in vitro protein digestibility as compared with defatted peanut flour. The processed cake meal can be blended with wheat flour to the extent of 10% (w/w) to prepare acceptable cookies with improved protein and mineral contents.

In vitro starch digestibility and predicted glycemic index of microwaved and conventionally baked pound cake.

PubMed

Sánchez-Pardo, María Elena; Ortiz-Moreno, Alicia; Mora-Escobedo, Rosalva; Necoechea-Mondragón, Hugo

2007-09-01

The present study compares the effect of baking process (microwave vs conventional oven) on starch bioavailability in fresh pound cake crumbs and in crumbs from pound cake stored for 8 days. Proximal chemical analysis, resistant starch (RS), retrograded starch (RS3) and starch hydrolysis index (HI) were evaluated. The empirical formula suggested by Granfeldt was used to determine the predicted glycemic index (pGI). Pound cake, one of Mexico's major bread products, was selected for analysis because the quality defects often associated with microwave baking might be reduced with the use of high-fat, high-moisture, batted dough. Differences in product moisture, RS and RS3 were observed in fresh microwave-baked and conventionally baked pound cake. RS3 increased significantly in conventionally baked products stored for 8 days at room temperature, whereas no significantly changes in RS3 were observed in the microwaved product. HI values for freshly baked and stored microwaved product were 59 and 62%, respectively (P > 0.05), whereas the HI value for the conventionally baked product decreased significantly after 8 days of storage. A pound cake with the desired HI and GI characteristics might be obtained by adjusting the microwave baking process.

Optimization of formulation of soy-cakes baked in infrared-microwave combination oven by response surface methodology.

PubMed

Şakıyan, Özge

2015-05-01

The aim of present work is to optimize the formulation of a functional cake (soy-cake) to be baked in infrared-microwave combination oven. For this optimization process response surface methodology was utilized. It was also aimed to optimize the processing conditions of the combination baking. The independent variables were the baking time (8, 9, 10 min), the soy flour concentration (30, 40, 50 %) and the DATEM (diacetyltartaric acid esters of monoglycerides) concentration (0.4, 0.6 and 0.8 %). The quality parameters that were examined in the study were specific volume, weight loss, total color change and firmness of the cake samples. The results were analyzed by multiple regression; and the significant linear, quadratic, and interaction terms were used in the second order mathematical model. The optimum baking time, soy-flour concentration and DATEM concentration were found as 9.5 min, 30 and 0.72 %, respectively. The corresponding responses of the optimum points were almost comparable with those of conventionally baked soy-cakes. So it may be declared that it is possible to produce high quality soy cakes in a very short time by using infrared-microwave combination oven.

Evaluation of a Shaker Dust Collector for Use in a Recirculating Ventilation System

PubMed Central

Sawvel, Russell A.; Park, Jae Hong; Anthony, T. Renée

2016-01-01

General ventilation with recirculated air may be cost-effective to control the concentration of low-toxicity, contaminants in workplaces with diffuse, dusty operations, such as in agriculture. Such systems are, however, rarely adopted with little evidence showing improved air quality and ability to operate under harsh conditions. The goal of this work was to examine the initial and long-term performance of a fabric-filter shaker dust collector (SDC) in laboratory tests and as deployed within a recirculating ventilation system in an agricultural building. In laboratory tests, collection efficiency and pressure drop were tracked over several filter loading cycles, and the recovery of filter capacity (pressure drop) from filter shaking was examined. Collection efficiencies of particles larger than 5 μm was high (>95%) even when the filter was pristine, showing effective collection of large particles that dominate inhalable concentrations typical of agricultural dusts. For respirable-sized particles, collection efficiencies were low when the filter was pristine (e.g., 27% for 1 μm) but much higher when a dust cake developed on the filter (>99% for all size particles), even after shaking (e.g., 90% for 1 μm). The first shake of a filter was observed to recovery a substantial fraction of filter capacity, with subsequent shakes providing little benefit. In field tests, the SDC performed effectively over a period of three months in winter when incorporated in a recirculating ventilation system of a swine farrowing room. Trends in collection efficiency and pressure drop with loading were similar to those observed in the laboratory with overall collection efficiencies high (>80%) when pressure drop exceeded 230 Pa, or 23% of the maximum loading recommended by the manufacturer. This work shows that the SDC can function effectively over the harsh winter in swine rearing operations. Together with findings of improved air quality in the farrowing room reported in a companion manuscript, this article provides evidence that an SDC represents a cost-effective solution to improve air quality in agricultural settings. PMID:25955507

Pozzolanic Activity Assessment of LUSI (LUmpur SIdoarjo) Mud in Semi High Volume Pozzolanic Mortar

PubMed Central

Hardjito, Djwantoro; Antoni; Wibowo, Gunadi M.; Christianto, Danny

2012-01-01

LUSI mud obtained from the mud volcano in Sidoarjo, Indonesia, is a viable aluminosilicate material to be utilized as pozzolanic material. LUSI is an abbreviation of the local name of the mud, i.e., Lumpur Sidoarjo, meaning Sidoarjo mud. This paper reports the results of an investigation to assess the pozzolanic activity of LUSI mud, especially in semi high volume pozzolanic mortar. In this case, the amount of mud incorporated is between 30% to 40% of total cementitious material, by mass. The content of SiO2 in the mud is about 30%, whilst the total content of SiO2, Fe2O3 and Al2O3 is more than 70%. Particle size and degree of partial cement replacement by treated LUSI mud affect the compressive strength, the strength activity index (SAI), the rate of pozzolanic activity development, and the workability of mortar incorporating LUSI mud. Manufacturing semi high volume LUSI mud mortar, up to at least 40% cement replacement, is a possibility, especially with a smaller particle size of LUSI mud, less than 63 μm. The use of a larger percentage of cement replacement by LUSI mud does not show any adverse effect on the water demand, as the flow of the fresh mortar increased with the increase of percentage of LUSI mud usage.

Pulse shaping system research of CdZnTe radiation detector for high energy x-ray diagnostic

NASA Astrophysics Data System (ADS)

Li, Miao; Zhao, Mingkun; Ding, Keyu; Zhou, Shousen; Zhou, Benjie

2018-02-01

As one of the typical wide band-gap semiconductor materials, the CdZnTe material has high detection efficiency and excellent energy resolution for the hard X-ray and the Gamma ray. The generated signal of the CdZnTe detector needs to be transformed to the pseudo-Gaussian pulse with a small impulse-width to remove noise and improve the energy resolution by the following nuclear spectrometry data acquisition system. In this paper, the multi-stage pseudo-Gaussian shaping-filter has been investigated based on the nuclear electronic principle. The optimized circuit parameters were also obtained based on the analysis of the characteristics of the pseudo-Gaussian shaping-filter in our following simulations. Based on the simulation results, the falling-time of the output pulse was decreased and faster response time can be obtained with decreasing shaping-time τs-k. And the undershoot was also removed when the ratio of input resistors was set to 1 to 2.5. Moreover, a two stage sallen-key Gaussian shaping-filter was designed and fabricated by using a low-noise voltage feedback operation amplifier LMH6628. A detection experiment platform had been built by using the precise pulse generator CAKE831 as the imitated radiation pulse which was equivalent signal of the semiconductor CdZnTe detector. Experiment results show that the output pulse of the two stage pseudo-Gaussian shaping filter has minimum 200ns pulse width (FWHM), and the output pulse of each stage was well consistent with the simulation results. Based on the performance in our experiment, this multi-stage pseudo-Gaussian shaping-filter can reduce the event-lost caused by pile-up in the CdZnTe semiconductor detector and improve the energy resolution effectively.

Carcass characteristics and meat quality of lambs fed babassu cake (Orbignya speciosa) as a replacement for elephant grass silage.

PubMed

Luz, Janaina Barros; Alves, Kaliandra Souza; Mezzomo, Rafael; Ribeiro Dos Santos Neta, Ernestina; Gomes, Daiany Íris; Sampaio Oliveira, Luis Rennan; Silva, Josiane Costa; Ramos de Carvalho, Francisco Fernando

2017-01-01

The study aimed to evaluate the effect of the partial replacement of elephant grass silage with babassu cake (Orbignya speciosa) on the carcass characteristics and meat quality of feedlot lambs. Forty-five castrated male Santa Ines sheep (19.08 ± 0.41 kg) approximately 4 months old were distributed in a completely randomized design, with five treatments 0.0, 12.5, 25.0, 37.5 and 50 % (%DM) replacement of babassu cake with silage forming isoproteic diets formulated at a ratio of 40 % roughage to 60 % concentrate. All of the studied animals were slaughtered at the end of the experiment. The liver weights and yields increased with the inclusion of babassu cake. The weight of the shoulder increased from 2.31 to 2.61 kg, while the loin yield decreased from 7.38 to 6.64 % with the inclusion of babassu cake, both linearly. The body length, thoracic perimeter, rump perimeter and carcass compactness index showed high and positive correlations with the hot and cold carcass weights. The myofibrillar fragmentation index decreased linearly as a function of the inclusion level of babassu cake, but other quality variables were not affected. The replacement of up to 50 % of the elephant grass silage with babassu cake in the diet of lambs does not cause negative effects on carcass characteristics or meat quality.

Rapid establishment of phenol- and quinoline-degrading consortia driven by the scoured cake layer in an anaerobic baffled ceramic membrane bioreactor.

PubMed

Wang, Wei; Wang, Shun; Ren, Xuesong; Hu, Zhenhu; Yuan, Shoujun

2017-11-01

Although toxic and refractory organics, such as phenol and quinoline, are decomposed by anaerobic bacteria, the establishment of specific degrading consortia is a relatively slow process. An anaerobic membrane bioreactor allows for complete biomass retention that can aid the establishment of phenol- and quinoline-degrading consortia. In this study, the anaerobic digestion of phenol (500 mg L -1 ) and quinoline (50 mg L -1 ) was investigated using an anaerobic baffled ceramic membrane bioreactor (ABCMBR). The results showed that, within 30 days, 99% of phenol, 98% of quinoline and 88% of chemical oxygen demand (COD) were removed. The substrate utilisation rates of the cake layer for phenol and quinoline, and specific methanogenic activity of the cake layer, were 7.58 mg phenol g -1  mixed liquor volatile suspended solids (MLVSS) day -1 , 8.23 mg quinoline g -1  MLVSS day -1 and 0.55 g COD CH4  g -1  MLVSS day -1 , respectively. The contribution of the cake layer to the removals of phenol and quinoline was extremely underestimated because the uncounted scoured cake layer was disregarded. Syntrophus was the key population for phenol and quinoline degradation, and it was more abundant in the cake layer than in the bulk sludge. The highly active scattered cake layer sped up the establishment of phenol- and quinoline-degrading consortia in the ABCMBR.

Presence of Fe-Al binary oxide adsorbent cake layer in ceramic membrane filtration and their impact for removal of HA and BSA.

PubMed

Kim, Kyung-Jo; Jang, Am

2018-04-01

To enhance the removal of natural organic matter (NOM) in ceramic (Ce) membrane filtration, an iron-aluminum binary oxide (FAO) was applied to the ceramic membrane surface as the adsorbent cake layer, and it was compared with heated aluminum oxide (HAO) for the evaluation of the control of NOM. Both the HAO and FAO adsorbent cake layers efficiently removed the NOM regardless of NOM's hydrophobic/hydrophilic characteristics, and the dissolved organic carbon (DOC) removal in NOM for FAO was 1-1.12 times greater than that for HAO, which means FAO was more efficient in the removal of DOC in NOM. FAO (0.03 μm), which is smaller in size than HAO (0.4 μm), had greater flux reduction than HAO. The flux reduction increased as the filtration proceeded because most of the organic foulants (colloid/particles and soluble NOM) were captured by the adsorbent cake layer, which caused fouling between the membrane surface and the adsorbent cake layer. However, no chemically irreversible fouling was observed on the Ce membrane at the end of the FAO adsorbent cake layer filtration. This means that a stable adsorbent cake layer by FAO formed on the Ce membrane, and that the reduced pure water flux of the Ce membrane, resulting from the NOM fouling, can easily be recovered through physicochemical cleaning. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optimization of palm oil extraction from Decanter cake of small crude palm oil mill by aqueous surfactant solution using RSM

NASA Astrophysics Data System (ADS)

Ahmadi Pirshahid, Shewa; Arirob, Wallop; Punsuvon, Vittaya

2018-04-01

The use of hexane to extract vegetable oil from oilseeds or seed cake is of growing concern due to its environmental impact such as its smelling and toxicity. In our method, used Response Surface Methodology (RSM) was applied to study the optimum condition of decanter cake obtained from small crude palm oil with aqueous surfactant solution. For the first time, we provide an optimum condition of preliminary study with decanter cake extraction to obtain the maximum of oil yield. The result from preliminary was further used in RSM study by using Central Composite Design (CCD) that consisted of thirty experiments. The effect of four independent variables: the concentration of Sodium Dodecyl Sulfate (SDS) as surfactant, temperature, the ratio by weight to volume of cake to surfactant solution and the amount of sodium chloride (NaCl) on dependent variables are studied. Data were analyzed using Design-Expert 8 software. The results showed that the optimum condition of decanter cake extraction were 0.016M of SDS solution concentration, 73°C of extraction temperature, 1:10 (g:ml) of the ratio of decanter cake to SDS solution and 2% (w/w) of NaCl amount. This condition gave 77.05% (w/w) oil yield. The chemical properties of the extracted palm oil from this aqueous surfactant extraction are further investigated compared with the hexane extraction. The obtained result showed that all properties of both extractions were nearly the same.

Analysis of the bacterial community in aged and aging pit mud of Chinese Luzhou-flavour liquor by combined PCR-DGGE and quantitative PCR assay.

PubMed

Liang, Huipeng; Li, Wenfang; Luo, Qingchun; Liu, Chaolan; Wu, Zhengyun; Zhang, Wenxue

2015-10-01

The community structure of bacteria in aged and aging pit mud, which was judged according to their sensory and physicochemical characteristics, was analysed using polymerase chain reaction denaturing gradient gel electrophoresis (PCR-DGGE) and quantitative real-time PCR (qPCR). The phyla Firmicutes, Actinobacteria, Proteobacteria, Synergistetes and Unclassified Bacteria were detected and the fermentative Firmicutes was predominant in both types of pit mud in the PCR-DGGE analysis. Among Firmicutes, Clostridiales was dominant in aged pit mud while Bacillales and Lactobacillales were dominant in aging pit mud. The diversity of bacterial communities in aged pit mud was higher than that in aging pit mud. In the qPCR analysis the abundance of Clostridium IV in aged pit mud was higher than that in aging pit mud and there were significant differences in the quantity of Clostridium IV between aged and aging pit mud of the same cellar (P < 0.05). There were some significant differences in the microbial community structure between aged and aging pit mud. The differences in the quantity of Clostridium IV might be involved in the distinction that the aged pit mud has a strong aroma while the aging pit mud does not. © 2014 Society of Chemical Industry.

Numerical simulation of mud erosion rate in sand-mud alternate layer and comparison with experiment

NASA Astrophysics Data System (ADS)

Yoshida, T.; Yamaguchi, T.; Oyama, H.; Sato, T.

2015-12-01

For gas production from methane hydrates in sand-mud alternate layers, depressurization method is expected as feasible. After methane hydrate is dissociated, gas and water flow in pore space. There is a concern about the erosion of mud surface and it may result in flow blockage that disturbs the gas production. As a part of a Japanese National hydrate research program (MH21, funded by METI), we developed a numerical simulation of water-induced mud erosion in pore-scale sand-mud domains to model such mud erosion. The size of which is of the order of 100 micro meter. Water flow is simulated using a lattice Boltzmann method (LBM) and mud surface is treated as solid boundary with arbitrary shape, which changes with time. Periodic boundary condition is adopted at the domain boundaries, except for the surface of mud layers and the upper side. Shear stress acting on the mud surface is calculated using a momentum-exchange method. Mud layer is eroded when the shear stress exceeds a threshold coined a critical shear stress. In this study, we compared the simulated mud erosion rate with experimental data acquired from an experiment using artificial sand-mud core. As a result, the simulated erosion rate agrees well with that of the experiment.

Mud volcanoes on Mars?

NASA Technical Reports Server (NTRS)

Komar, Paul D.

1991-01-01

The term mud volcano is applied to a variety of landforms having in common a formation by extrusion of mud from beneath the ground. Although mud is the principal solid material that issues from a mud volcano, there are many examples where clasts up to boulder size are found, sometimes thrown high into the air during an eruption. Other characteristics of mud volcanoes (on Earth) are discussed. The possible presence of mud volcanoes, which are common and widespread on Earth, on Mars is considered.

Linked halokinesis and mud volcanism at the Mercator mud volcano, Gulf of Cadiz

NASA Astrophysics Data System (ADS)

Perez-Garcia, Carolina; Berndt, Christian; Klaeschen, Dirk; Mienert, Jürgen; Haffert, Laura; Depreiter, Davy; Haeckel, Matthias

2011-05-01

Mud volcanoes are seafloor expressions of focused fluid flow that are common in compressional tectonic settings. New high-resolution 3-D seismic data from the Mercator mud volcano (MMV) and an adjacent buried mud volcano (BMV) image the internal structure of the top 800 m of sediment at both mud volcanoes, revealing that both are linked and have been active episodically. The total volumes of extruded mud range between 0.15 and 0.35 km3 and 0.02-0.05 km3 for the MMV and the BMV, respectively. The pore water composition of surface sediment samples suggests that halokinesis has played an important role in the evolution of the mud volcanoes. We propose that erosion of the top of the Vernadsky Ridge that underlies the mud volcanoes activated salt movement, triggering deep migration of fluids, dissolution of salt, and sediment liquefaction and mobilization since the end of the Pliocene. Since beginning of mud volcanism in this area, the mud volcanoes erupted four times while there was only one reactivation of salt tectonics. This implies that there are other mechanisms that trigger mud eruptions. The stratigraphic relationship of mudflows from the MMV and BMV indicates that the BMV was triggered by the MMV eruptions. This may either be caused by loading-induced hydrofracturing within the BMV or due to a common feeder system for both mud volcanoes. This study shows that the mud volcanoes in the El Arraiche mud volcano field are long-lived features that erupt with intervals of several tens of thousands of years.

Mud volcanoes of the Orinoco Delta, Eastern Venezuela

USGS Publications Warehouse

Aslan, A.; Warne, A.G.; White, W.A.; Guevara, E.H.; Smyth, R.C.; Raney, J.A.; Gibeaut, J.C.

2001-01-01

Mud volcanoes along the northwest margin of the Orinoco Delta are part of a regional belt of soft sediment deformation and diapirism that formed in response to rapid foredeep sedimentation and subsequent tectonic compression along the Caribbean-South American plate boundary. Field studies of five mud volcanoes show that such structures consist of a central mound covered by active and inactive vents. Inactive vents and mud flows are densely vegetated, whereas active vents are sparsely vegetated. Four out of the five mud volcanoes studied are currently active. Orinoco mud flows consist of mud and clayey silt matrix surrounding lithic clasts of varying composition. Preliminary analysis suggests that the mud volcano sediment is derived from underlying Miocene and Pliocene strata. Hydrocarbon seeps are associated with several of the active mud volcanoes. Orinoco mud volcanoes overlie the crest of a mud-diapir-cored anticline located along the axis of the Eastern Venezuelan Basin. Faulting along the flank of the Pedernales mud volcano suggests that fluidized sediment and hydrocarbons migrate to the surface along faults produced by tensional stresses along the crest of the anticline. Orinoco mud volcanoes highlight the proximity of this major delta to an active plate margin and the importance of tectonic influences on its development. Evaluation of the Orinoco Delta mud volcanoes and those elsewhere indicates that these features are important indicators of compressional tectonism along deformation fronts of plate margins. ?? 2001 Elsevier Science B.V. All rights reserved.

Closure Report for Corrective Action Unit 544: Cellars, Mud Pits, and Oil Spills, Nevada National Security Site, Nevada, Revision 0

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mark Krauss and Catherine Birney

2011-05-01

This Closure Report (CR) presents information supporting the closure of Corrective Action Unit (CAU) 544: Cellars, Mud Pits, and Oil Spills, Nevada National Security Site, Nevada. This CR complies with the requirements of the Federal Facility Agreement and Consent Order that was agreed to by the State of Nevada; U.S. Department of Energy (DOE), Environmental Management; U.S. Department of Defense; and DOE, Legacy Management. The corrective action sites (CASs) within CAU 544 are located within Areas 2, 7, 9, 10, 12, 19, and 20 of the Nevada National Security Site. Corrective Action Unit 544 comprises the following CASs: • 02-37-08,more » Cellar & Mud Pit • 02-37-09, Cellar & Mud Pit • 07-09-01, Mud Pit • 09-09-46, U-9itsx20 PS #1A Mud Pit • 10-09-01, Mud Pit • 12-09-03, Mud Pit • 19-09-01, Mud Pits (2) • 19-09-03, Mud Pit • 19-09-04, Mud Pit • 19-25-01, Oil Spill • 19-99-06, Waste Spill • 20-09-01, Mud Pits (2) • 20-09-02, Mud Pit • 20-09-03, Mud Pit • 20-09-04, Mud Pits (2) • 20-09-06, Mud Pit • 20-09-07, Mud Pit • 20-09-10, Mud Pit • 20-25-04, Oil Spills • 20-25-05, Oil Spills The purpose of this CR is to provide documentation supporting the completed corrective actions and data confirming that the closure objectives for CASs within CAU 544 were met. To achieve this, the following actions were performed: • Review the current site conditions, including the concentration and extent of contamination. • Implement any corrective actions necessary to protect human health and the environment. • Properly dispose of corrective action and investigation wastes. • Document Notice of Completion and closure of CAU 544 issued by the Nevada Division of Environmental Protection.« less

DPPH radical scavenging activity of a mixture of fatty acids and peptide-containing compounds in a protein hydrolysate of Jatropha curcas seed cake.

PubMed

Phengnuam, Thanyarat; Goroncy, Alexander K; Rutherfurd, Shane M; Moughan, Paul J; Suntornsuk, Worapot

2013-12-04

Jatropha curcas, a tropical plant, has great potential commercial relevance as its seeds have high oil content. The seeds can be processed into high-quality biofuel producing seed cake as a byproduct. The seed cake, however, has not gotten much attention toward its potential usefulness. This work was aimed to determine the antioxidant activity of different fractions of a protein hydrolysate from J. curcas seed cake and to elucidate the molecular structures of the antioxidants. Seed cake was first processed into crude protein isolate and the protein was hydrolyzed by Neutrase. The hydrolysate obtained from 1 h of Neutrase hydrolysis showed the strongest antioxidant activity against DPPH radical (2,2-diphenyl-1-picrylhydrazyl). After a purification series of protein hydrolysate by liquid chromatography, chemicals acting as DPPH radical inhibitors were found to be a mixture of fatty acids, fatty acid derivatives, and a small amount of peptides characterized by mass spectrometry and nuclear magnetic resonance (NMR) spectroscopy.

Evening primrose (Oenothera paradoxa) cake as an unconventional protein source.

PubMed

Golabczak, J; Py, R

2003-01-01

An efficient procedure of a protein isolate production from the evening primrose cake was developed. The cake is a by-product of oil extraction from seeds by using the cold pressing method. The evening primrose cake contains 22.7% of protein. Its content in the protein isolate derived from the cake is 74%. Proteins present in evening primrose seeds are rich in Trp (7%) and Met (3%), but Lys-deficient (1.3%) as compared to the FAO protein standard. Apart from the proteins, the protein isolate contains 8.5% (w/w per s.s.) dietary fiber, that negatively affects its digestibility. To enhance the bio-availability of the protein isolate, it was partially hydrolyzed with commercial preparations of trypsin and other proteases (Alcalase and Flavourzyme, Novozymes. Denmark). The most advanced proteolysis (52%) was achieved by 6 h digestion of 2% protein suspension with a mixture of Flavourzyme and Alcalase (350 and 600 U per g of protein, respectively) at 50 degrees C and pH 9.0.

Neem cake as a promising larvicide and adulticide against the rural malaria vector Anopheles culicifacies (Diptera: Culicidae): a HPTLC fingerprinting approach.

PubMed

Benelli, Giovanni; Chandramohan, Balamurugan; Murugan, Kadarkarai; Madhiyazhagan, Pari; Kovendan, Kalimuthu; Panneerselvam, Chellasamy; Dinesh, Devakumar; Govindarajan, Marimuthu; Higuchi, Akon; Toniolo, Chiara; Canale, Angelo; Nicoletti, Marcello

2017-05-01

Mosquitoes are insects of huge public health importance, since they act as vectors for important pathogens and parasites. Here, we focused on the possibility of using the neem cake in the fight against mosquito vectors. The neem cake chemical composition significantly changes among producers, as evidenced by our HPTLC (High performance thin layer chromatography) analyses of different marketed products. Neem cake extracts were tested to evaluate the ovicidal, larvicidal and adulticidal activity against the rural malaria vector Anopheles culicifacies. Ovicidal activity of both types of extracts was statistically significant, and 150 ppm completely inhibited egg hatching. LC 50 values were extremely low against fourth instar larvae, ranging from 1.321 (NM1) to 1.818 ppm (NA2). Adulticidal activity was also high, with LC 50 ranging from 3.015 (NM1) to 3.637 ppm (NM2). This study pointed out the utility of neem cake as a source of eco-friendly mosquitocides in Anopheline vector control programmes.

Proposal of a taste evaluating method of the sponge cake by using 3D range sensor

NASA Astrophysics Data System (ADS)

Kato, Kunihito; Yamamoto, Kazuhiko; Ogawa, Noriko

2002-10-01

Nowadays, the image processing techniques are while applying to the food industry in many situations. The most of these researches are applications for the quality control in plants, and there are hardly any cases of measuring the 'taste'. We are developing the measuring system of the deliciousness by using the image sensing. In this paper, we propose the estimation method of the deliciousness of a sponge cake. Considering about the deliciousness of the sponge cake, if the size of the bubbles on the surface is small and the number of them is large, then it is defined that the deliciousness of the sponge cake is better in the field of the food science. We proposed a method of detection bubbles in the surface of the sectional sponge cake automatically by using 3-D image processing. By the statistical information of these detected bubbles based on the food science, the deliciousness is estimated.

Solid-State Treatment of Castor Cake Employing the Enzymatic Cocktail Produced from Pleurotus djamor Fungi.

PubMed

Sánchez-Cantú, Manuel; Ortiz-Moreno, Liliana; Ramos-Cassellis, María E; Marín-Castro, Marco; De la Cerna-Hernández, C

2018-06-01

In this work, the enzymatic cocktail produced by Pleurotus djamor fungi extracted at pH of 4.8 and 5.3 was employed for castor cake solid-state treatment. Proximal, X-ray powder diffraction and scanning electron microscopy analysis of the pristine castor cake were carried out. First, Pleurotus djamor stain was inoculated in castor cake for the enzymatic production and the enzymatic activity was determined. The maximum enzymatic activity was identified at days 14 (65.9 UI/gss) and 11 (140.3 UI/gss) for the enzymatic cocktail obtained at pH 5.3 and 4.8, respectively. Then, the enzymatic cocktail obtained at the highest enzymatic activity days was employed directly over castor cake. Lignin was degraded throughout incubation time achieving a 47 and 45% decrease for the cocktail produced at pH 4.8 and 5.3, correspondingly. These results were corroborated by the SEM and XRD analysis where a higher porosity and xylan degradation were perceived throughout the enzymatic treatment.

Monitoring the crystallization of starch and lipid components of the cake crumb during staling.

PubMed

Hesso, N; Le-Bail, A; Loisel, C; Chevallier, S; Pontoire, B; Queveau, D; Le-Bail, P

2015-11-20

Cake staling is a complex problem which has still not been fully understood. Starch polymers retrogradation, which is linked to biopolymers recrystallisation, is the most important factor affecting cake firmness in addition to water migration and fat crystallization. In this study, the effect of storage temperatures of 4°C and 20°C on starch retrogradation and fat recrystallization was investigated. Starch retrogradation can be tracked through changes in crystalline structure via X-rays diffraction as well as through melting of crystals via calorimetry. These techniques have been coupled to study the different phenomena occurring during staling. The results revealed that the storage of cakes at 20°C for 25 days showed more starch polymer retrogradation and more intense fat recrystallization in the β form than at 4°C. Consequently, the staling was delayed when a low storage temperature like 4°C was used, which is recommended to retain high quality cakes during storage. Copyright © 2015 Elsevier Ltd. All rights reserved.

Cyclic Activity of Mud Volcanoes: Evidences from Trinidad (SE Caribbean)

NASA Astrophysics Data System (ADS)

Deville, E.

2007-12-01

Fluid and solid transfer in mud volcanoes show different phases of activity, including catastrophic events followed by periods of relative quiescence characterized by moderate activity. This can be notably shown by historical data onshore Trinidad. Several authors have evoked a possible link between the frequencies of eruption of some mud volcanoes and seismic activity, but in Trinidad there is no direct correlation between mud eruptions and seisms. It appears that each eruptive mud volcano has its own period of catastrophic activity, and this period is highly variable from one volcano to another. The frequency of activity of mud volcanoes seems essentially controlled by local pressure regime within the sedimentary pile. At the most, a seism can, in some cases, activate an eruption close to its term. The dynamics of expulsion of the mud volcanoes during the quiescence phases has been studied notably from temperature measurements within the mud conduits. The mud temperature is concurrently controlled by, either, the gas flux (endothermic gas depressurizing induces a cooling effect), or by the mud flux (mud is a vector for convective heat transfer). Complex temperature distribution was observed in large conduits and pools. Indeed, especially in the bigger pools, the temperature distribution characterizes convective cells with an upward displacement of mud above the deep outlet, and ring-shaped rolls associated with the burial of the mud on the flanks of the pools. In simple, tube-like shaped, narrow conduits, the temperature is more regular, but we observed different types of profiles, with either downward increasing or decreasing temperatures. If the upward flow of mud would be regular, we should expect increasing temperatures and progressively decreasing gradient with depth within the conduits. However, the variable measured profiles from one place to another, as well as time-variable measured temperatures within the conduits and especially, at the base of the conduits, shows that the fluid flow expelled by the studied mud volcanoes is not constant but highly variable through short time-periods. We notably observed very short time-period cyclic variations with a frequency of about 10 minutes. These high frequencies temperature changes could be related to the dynamics of two-phase flows (gas and mud) through the mud volcano conduits. We also observed locally a significant daily changes of the temperature of the expelled mud which shows also that the mud flux is changing very rapidly from one day to another.

Method of decontaminating a contaminated fluid by using photocatalytic particles

NASA Technical Reports Server (NTRS)

Cooper, Gerald (Inventor); Ratcliff, Matthew A. (Inventor)

1994-01-01

A system for decontaminating the contaminated fluid by using photocatalytic particles. The system includes a reactor tank for holding the contaminated fluid and the photocatalytic particles suspended in the contaminated fluid to form a slurry. Light irradiates the surface of the slurry, thereby activating the photocatalytic properties of the particles. The system also includes stirring blades for continuously agitating the irradiated fluid surface and for maintaining the particles in a suspended state within the fluid. The system also includes a cross flow filter for segregating the fluid (after decomposition) from the semiconductor powder. The cross flow filter is occasionally back flushed to remove any semiconductor powder that might have caked on the filter. The semiconductor powder may be recirculated back to the tank for reuse, or may be stored for future use. A series of such systems may be used to gradually decompose a chemical in the fluid. Preferably, the fluid is pretreated to remove certain metal ions which interfere with the photocatalytic process. Such pretreatment may be accomplished by dispersing semiconductor particles within the fluid, which adsorb ions or photodeposit the metal as the free metal or its insoluble oxide or hydroxide, and then removing the semiconductor particles together with the adsorbed metal ions/oxides/hydroxide/free metal from the fluid. A method of decontaminating a contaminated fluid is also disclosed.

Effects of potassium ferrate on extracellular polymeric substances (EPS) and physicochemical properties of excess activated sludge.

PubMed

Ye, Fenxia; Liu, Xinwen; Li, Ying

2012-01-15

The activated sludge process of wastewater results in the generation of a considerable amount of excess activated sludge. In many wastewater treatment plants, the bottleneck of the sludge handling system is the dewatering operation. This paper investigated the effect of potassium ferrate pretreatment on the physicochemical properties of the excess activated sludge at various dosages of potassium ferrate. The particle size, extracellular polymeric substances (EPS) content and chemical components, and sludge disintegration degree were measured to explain the observed changes of physicochemical properties. It was expected that potassium ferrate could enhance the filterability and dewaterability of the sludge. However, the results showed that potassium ferrate had a negative effect on the filterability by measuring the capillary suction time (CST), but improved the settleability and dewaterability extent by determining the water content in the dewatered cake, although the flocs size reduced slightly. Loosely bound EPS (LB-EPS) content, polysaccharides (PS) and proteins (PN) contents in LB-EPS all increased with increasing the amount of potassium ferrate. However, Tightly bound EPS (TB-EPS) content, PS and PN contents in TB-EPS did not changed significantly at first, and decreased slightly under higher dosage of potassium ferrate. EPS, especially LB-EPS played more important role in the observed changes of the settleability and filterability than the sludge particle size. Copyright © 2011 Elsevier B.V. All rights reserved.

Preliminary analytical results for a mud sample collected from the LUSI Mud Volcano, Sidoarjo, East Java, Indonesia

USGS Publications Warehouse

Plumlee, Geoffrey S.; Casadevall, Thomas J.; Wibowo, Handoko T.; Rosenbauer, Robert J.; Johnson, Craig A.; Breit, George N.; Lowers, Heather; Wolf, Ruth E.; Hageman, Philip L.; Goldstein, Harland L.; Anthony, Michael W.; Berry, Cyrus J.; Fey, David L.; Meeker, Gregory P.; Morman, Suzette A.

2008-01-01

On May 29, 2006, mud and gases began erupting unexpectedly from a vent 150 meters away from a hydrocarbon exploration well near Sidoarjo, East Java, Indonesia. The eruption, called the LUSI (Lumpur 'mud'-Sidoarjo) mud volcano, has continued since then at rates as high as 160,000 m3 per day. At the request of the United States Department of State, the U.S. Geological Survey (USGS) has been providing technical assistance to the Indonesian Government on the geological and geochemical aspects of the mud eruption. This report presents initial characterization results of a sample of the mud collected on September 22, 2007, as well as inerpretive findings based on the analytical results. The focus is on characteristics of the mud sample (including the solid and water components of the mud) that may be of potential environmental or human health concern. Characteristics that provide insights into the possible origins of the mud and its contained solids and waters have also been evaluated.

Cake: Enabling High-level SLOs on Shared Storage Systems

DTIC Science & Technology

2012-11-07

Cake: Enabling High-level SLOs on Shared Storage Systems Andrew Wang Shivaram Venkataraman Sara Alspaugh Randy H. Katz Ion Stoica Electrical...Date) * * * * * * * Professor R. Katz Second Reader (Date) Cake: Enabling High-level SLOs on Shared Storage Systems Andrew Wang, Shivaram Venkataraman ...Report MIT-LCS-TR-667, MIT, Laboratory for Computer Science, 1995. [39] A. Wang, S. Venkataraman , S. Alspaugh, I. Stoica, and R. Katz. Sweet storage SLOs

Fuzzy Logic-based expert system for evaluating cake quality of freeze-dried formulations.

PubMed

Trnka, Hjalte; Wu, Jian X; Van De Weert, Marco; Grohganz, Holger; Rantanen, Jukka

2013-12-01

Freeze-drying of peptide and protein-based pharmaceuticals is an increasingly important field of research. The diverse nature of these compounds, limited understanding of excipient functionality, and difficult-to-analyze quality attributes together with the increasing importance of the biosimilarity concept complicate the development phase of safe and cost-effective drug products. To streamline the development phase and to make high-throughput formulation screening possible, efficient solutions for analyzing critical quality attributes such as cake quality with minimal material consumption are needed. The aim of this study was to develop a fuzzy logic system based on image analysis (IA) for analyzing cake quality. Freeze-dried samples with different visual quality attributes were prepared in well plates. Imaging solutions together with image analytical routines were developed for extracting critical visual features such as the degree of cake collapse, glassiness, and color uniformity. On the basis of the IA outputs, a fuzzy logic system for analysis of these freeze-dried cakes was constructed. After this development phase, the system was tested with a new screening well plate. The developed fuzzy logic-based system was found to give comparable quality scores with visual evaluation, making high-throughput classification of cake quality possible. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

Bubble structure evaluation method of sponge cake by using image morphology

NASA Astrophysics Data System (ADS)

Kato, Kunihito; Yamamoto, Kazuhiko; Nonaka, Masahiko; Katsuta, Yukiyo; Kasamatsu, Chinatsu

2007-01-01

Nowadays, many evaluation methods for food industry by using image processing are proposed. These methods are becoming new evaluation method besides the sensory test and the solid-state measurement that have been used for the quality evaluation recently. The goal of our research is structure evaluation of sponge cake by using the image processing. In this paper, we propose a feature extraction method of the bobble structure in the sponge cake. Analysis of the bubble structure is one of the important properties to understand characteristics of the cake from the image. In order to take the cake image, first we cut cakes and measured that's surface by using the CIS scanner, because the depth of field of this type scanner is very shallow. Therefore the bubble region of the surface has low gray scale value, and it has a feature that is blur. We extracted bubble regions from the surface images based on these features. The input image is binarized, and the feature of bubble is extracted by the morphology analysis. In order to evaluate the result of feature extraction, we compared correlation with "Size of the bubble" of the sensory test result. From a result, the bubble extraction by using morphology analysis gives good correlation. It is shown that our method is as well as the subjectivity evaluation.

Chocolate cake. Guilt or celebration? Associations with healthy eating attitudes, perceived behavioural control, intentions and weight-loss.

PubMed

Kuijer, Roeline G; Boyce, Jessica A

2014-03-01

Food and eating are often associated with ambivalent feelings: pleasure and enjoyment, but also worry and guilt. Guilt has the potential to motivate behaviour change, but may also lead to feelings of helplessness and loss of control. This study firstly examined whether a default association of either 'guilt' or 'celebration' with a prototypical forbidden food item (chocolate cake) was related to differences in attitudes, perceived behavioural control, and intentions in relation to healthy eating, and secondly whether the default association was related to weight change over an 18month period (and short term weight-loss in a subsample of participants with a weight-loss goal). This study did not find any evidence for adaptive or motivational properties of guilt. Participants associating chocolate cake with guilt did not report more positive attitudes or stronger intentions to eat healthy than did those associating chocolate cake with celebration. Instead, they reported lower levels of perceived behavioural control over eating and were less successful at maintaining their weight over an 18month period. Participants with a weight-loss goal who associated chocolate cake with guilt were less successful at losing weight over a 3month period compared to those associating chocolate cake with celebration. Copyright © 2014. Published by Elsevier Ltd.

An observational study of the effect of vibration on the caking of suspensions in oily vehicles.

PubMed

Jain, Rohit; Bork, Olaf; Alawi, Fadil; Nanjan, Karthigeyan; Tucker, Ian G

2016-11-30

An oily suspension of penethamate (PNT) that was physically stable on storage, caked solidly during road/air transport. This paper reports on the caking behaviour of PNT oily suspension formulations exposed to vibrations in a lab-based test designed to simulate road/air transport. The lab-test was used to study the effects of container type (glass v PET) and formulation (oil, surfactant type and concentration) on the physical stability of suspension under vibration. Redispersibility of the sediment was lower at longer vibrations times and at higher intensity of vibration. Caking on vibration was strongly influenced by the type of container (caking in glass but not in PET) possibly due to tribo-charging of particles. Caking on vibration was dependent on the formulation: type and concentration of surfactant; type of oil. The physical stability of oily suspensions, and the effect of vibration are two areas which have been largely neglected in the pharmaceutical literature. This paper discusses some potential mechanisms for the observations but studies using fully characterised materials are required. Finally we conclude that static testing of physical stability of oily suspensions is not sufficient and that a vibrational stress test is required. Copyright © 2016 Elsevier B.V. All rights reserved.

Utilization of wild apricot kernel press cake for extraction of protein isolate.

PubMed

Sharma, P C; Tilakratne, B M K S; Gupta, Anil

2010-12-01

The kernels of apricot (Prunus armeniaca) stones are utilized for extraction of oil. The press cake left after extraction of oil was evaluated for preparation of protein isolate for its use in food supplementation. The apricot kernels contained 45-50% oil, 23.6-26.2% protein, 4.2% ash, 5.42% crude fibre, 8.2% carbohydrates and 90 mg HCN/100 g kernels, while press cake obtained after oil extraction contained 34.5% crude protein, which can be utilized for preparation of protein isolates. The method standardized for extraction of protein isolate broadly consisted of boiling the press cake with water in 1:20 (w/v) ratio for 1 h, raising pH to 8 and stirring for a few min followed by filtration, coagulation at pH 4 prior to sieving and pressing of coagulant for overnight and drying followed by grinding which resulted in extraction of about 71.3% of the protein contained in the press cake. The protein isolate contained 68.8% protein, 6.4% crude fat, 0.8% ash, 2.2% crude fibre and 12.7% carbohydrates. Thus the apricot kernel press cake can be utilized for preparation of protein isolate to improve the nutritional status of many food formulations.

Impact of potassium bromate and potassium iodate in a pound cake system.

PubMed

Wilderjans, Edith; Lagrain, Bert; Brijs, Kristof; Delcour, Jan A

2010-05-26

This study investigates the impact of the oxidants potassium bromate and potassium iodate (8, 16, 32, 64, and 128 micromol/g dry matter of egg white protein) on pound cake making. The impact of the oxidants on egg white characteristics was studied in a model system. Differential scanning calorimetry showed that the oxidants caused egg white to denature later. During heating in a rapid visco analyzer, the oxidants caused the free sulfhydryl (SH) group levels to decrease more intensively and over a smaller temperature range. The oxidants made the proteins more resistant to decreases in protein extractability in sodium dodecyl sulfate containing buffer during cake recipe mixing and less resistant to such decreases during cake baking. We assume that, during baking, the degree to which SH/disulfide exchange and SH oxidation can occur depends on the properties of the protein at the onset of the process. In our view, the prevention of extractability loss during mixing increased the availability of SH groups and caused more such loss during baking. During cooling, all cakes baked with added oxidants showed less collapse. On the basis of the presented data, we put forward that only those protein reactions that occur during baking contribute to the formation of a network that supports final cake structure and prevents collapse.

[Optimization of formulations for dietetic pastry products].

PubMed

Villarroel, M; Uquiche, E; Brito, G; Cancino, M

2000-03-01

Optimized formulations of dietetic pastry products such as cake and sponge cake premixes were formulated using the surface response methodology. % Emulsifier agent and baking time were the selected independent variables for cake, as well as % emulsifier agent % chlorinated flour the variables selected for sponge cake. Three different level of each variable summing up thirteen experimental formulae of each product were assessed to optimize the variables that could have some influence in the sensory characteristics of these dietetic products. The total sensory quality was determined for both dietetic products using the composite scoring test and a panel of 18 trained judges. Looking at the contour graphic and considering economic aspects the best combination of variables for cake formulation was 2% emulsifier agent and 48 minutes for baking time, With respect to sponge cake, the best combination was 6% emulsifier agent and 48% chlorinated flour. Shelf life studies showed that both dietetic formulations remained stable during storage conditions of 75 days at 30 degrees C. During this period, significant differences in sensory characteristics were not found (p < 0.05). Data of peroxide values were kept under the critical value reported for detection of organoleptic rancidity. Reported values of hedonic test showed that these dietetics pastry products had good acceptability, and open up marketing opportunities for new products with potential health benefits to consumers.

Degree of roasting of carob flour affecting the properties of gluten-free cakes and cookies.

PubMed

Román, Laura; González, Ana; Espina, Teresa; Gómez, Manuel

2017-06-01

Carob flour is a product rich in fibre obtained from by-products of the locust bean gum extraction processing. The flour is commercialised with different degrees of roasting in order to improve its organoleptic characteristics. In this study, carob flour with three different roasting degrees was used to replace rice flour (15%) in gluten-free cakes and cookies. The influence of this replacement was studied on the psychochemical characteristics and acceptability of the final products. The incorporation of carob flour increased the viscosity of cake batters and increased the solid elastic-like behaviour of the cookie doughs, indicating a stronger interaction among the formula ingredients. The inclusion of carob flour, with a low time of roasting, did not lead to any significant differences in the specific volume and hardness of the cakes, but reduced cake staling and the thickness and width of the cookies. Darker colours were obtained when carob flour was incorporated into the product. The acceptability of cakes was only reduced with the addition of highly roasted carob flour, while in the case of cookies there was a decline in the acceptability of all carob flour cookies, which was mostly perceived with the highest roasting degree, something mainly attributed to the bitter taste of the products.

Simultaneous allergen inactivation and detoxification of castor bean cake by treatment with calcium compounds

PubMed Central

Fernandes, K.V.; Deus-de-Oliveira, N.; Godoy, M.G.; Guimarães, Z.A.S.; Nascimento, V.V.; de Melo, E.J.T.; Freire, D.M.G.; Dansa-Petretski, M.; Machado, O.L.T.

2012-01-01

Ricinus communis L. is of great economic importance due to the oil extracted from its seeds. Castor oil has been used for pharmaceutical and industrial applications, as a lubricant or coating agent, as a component of plastic products, as a fungicide or in the synthesis of biodiesel fuels. After oil extraction, a castor cake with a large amount of protein is obtained. However, this by-product cannot be used as animal feed due to the presence of toxic (ricin) and allergenic (2S albumin) proteins. Here, we propose two processes for detoxification and allergen inactivation of the castor cake. In addition, we establish a biological test to detect ricin and validate these detoxification processes. In this test, Vero cells were treated with ricin, and cell death was assessed by cell counting and measurement of lactate dehydrogenase activity. The limit of detection of the Vero cell assay was 10 ng/mL using a concentration of 1.6 × 105 cells/well. Solid-state fermentation (SSF) and treatment with calcium compounds were used as cake detoxification processes. For SSF, Aspergillus niger was grown using a castor cake as a substrate, and this cake was analyzed after 24, 48, 72, and 96 h of SSF. Ricin was eliminated after 24 h of SSF treatment. The cake was treated with 4 or 8% Ca(OH)2 or CaO, and both the toxicity and the allergenic properties were entirely abolished. A by-product free of toxicity and allergens was obtained. PMID:22911344

Fumaric acid production using renewable resources from biodiesel and cane sugar production processes.

PubMed

Papadaki, Aikaterini; Papapostolou, Harris; Alexandri, Maria; Kopsahelis, Nikolaos; Papanikolaou, Seraphim; de Castro, Aline Machado; Freire, Denise M G; Koutinas, Apostolis A

2018-04-13

The microbial production of fumaric acid by Rhizopus arrhizus NRRL 2582 has been evaluated using soybean cake from biodiesel production processes and very high polarity (VHP) sugar from sugarcane mills. Soybean cake was converted into a nutrient-rich hydrolysate via a two-stage bioprocess involving crude enzyme production via solid state fermentations (SSF) of either Aspergillus oryzae or R. arrhizus cultivated on soybean cake followed by enzymatic hydrolysis of soybean cake. The soybean cake hydrolysate produced using crude enzymes derived via SSF of R. arrhizus was supplemented with VHP sugar and evaluated using different initial free amino nitrogen (FAN) concentrations (100, 200, and 400 mg/L) in fed-batch cultures for fumaric acid production. The highest fumaric acid concentration (27.3 g/L) and yield (0.7 g/g of total consumed sugars) were achieved when the initial FAN concentration was 200 mg/L. The combination of VHP sugar with soybean cake hydrolysate derived from crude enzymes produced by SSF of A. oryzae at 200 mg/L initial FAN concentration led to the production of 40 g/L fumaric acid with a yield of 0.86 g/g of total consumed sugars. The utilization of sugarcane molasses led to low fumaric acid production by R. arrhizus, probably due to the presence of various minerals and phenolic compounds. The promising results achieved through the valorization of VHP sugar and soybean cake suggest that a focused study on molasses pretreatment could lead to enhanced fumaric acid production.

Assessment of Jatropha curcas L. biodiesel seed cake toxicity using the zebrafish (Danio rerio) embryo toxicity (ZFET) test.

PubMed

Hallare, Arnold V; Ruiz, Paulo Lorenzo S; Cariño, J C Earl D

2014-05-01

Consequent to the growing demand for alternative sources of energy, the seeds from Jatropha curcas remain to be the favorite for biodiesel production. However, a significant volume of the residual organic mass (seed cake) is produced during the extraction process, which raises concerns on safe waste disposal. In the present study, we assessed the toxicity of J. curcas seed cake using the zebrafish (Danio rerio) embryotoxicity test. Within 1-h post-fertilization (hpf), the fertilized eggs were exposed to five mass concentrations of J. curcas seed cake and were followed through 24, 48, and 72 hpf. Toxicity was evaluated based on lethal endpoints induced on zebrafish embryos namely egg coagulation, non-formation of somites, and non-detachment of tail. The lowest concentration tested, 1 g/L, was not able to elicit toxicity on embryos whereas 100 % mortality (based also on lethal endpoints) was recorded at the highest concentration at 2.15 g/L. The computed LC50 for the J. curcas seed cake was 1.61 g/L. No further increase in mortality was observed in the succeeding time points (48 and 72 hpf) indicating that J. curcas seed cake exerted acute toxicity on zebrafish embryos. Sublethal endpoints (yolk sac and pericardial edema) were noted at 72 hpf in zebrafish embryos exposed to higher concentrations. The observed lethal endpoints induced on zebrafish embryos were discussed in relation to the active principles, notably, phorbol esters that have remained in the seed cake even after extraction.

Dielectric properties, optimum formulation and microwave baking conditions of chickpea cakes.

PubMed

Alifakı, Yaşar Özlem; Şakıyan, Özge

2017-03-01

The aim of this study was to correlate dielectric properties with quality parameters, and to optimize cake formulation and baking conditions by response surface methodology. Weight loss, color, specific volume, hardness and porosity were evaluated. The samples with different DATEM (0.4, 0.8 and 1.2%) and chickpea flour concentrations (30, 40 and 50%) were baked in microwave oven at different power (300, 350, 400 W) and baking times (2.50, 3.0, 3.50 min). It was found that microwave power showed significant effect on color, while baking time showed effect on weight loss, porosity, hardness, specific volume and dielectric properties. Emulsifier level affected porosity, specific volume and dielectric constant. Chickpea flour level affected porosity, color, hardness and dielectric properties of cakes. The optimum microwave power, baking time, DATEM level and chickpea flour level were found as 400 W, 2.84 min, 1.2% and 30%, respectively. The comparison between conventionally baked and the microwave baked cakes at optimum points showed that color difference, weight loss, specific volume and porosity values of microwave baked cakes were less than those of conventionally baked cakes, on the other hand, hardness values were higher. Moreover, a negative correlation between dielectric constant and porosity, and weight loss values were detected for microwave baked samples. A negative correlation between dielectric loss factor and porosity was observed. These correlations indicated that quality characteristics of a microwave baked cake sample can be assessed from dielectric properties. These correlations provides understanding on the behavior of food material during microwave processing.

Rapeseed and Raspberry Seed Cakes as Inexpensive Raw Materials in the Production of Activated Carbon by Physical Activation: Effect of Activation Conditions on Textural and Phenol Adsorption Characteristics

PubMed Central

Smets, Koen; De Jong, Mats; Lupul, Iwona; Gryglewicz, Grazyna; Schreurs, Sonja; Carleer, Robert; Yperman, Jan

2016-01-01

The production of activated carbons (ACs) from rapeseed cake and raspberry seed cake using slow pyrolysis followed by physical activation of the obtained solid residues is the topic of this study. The effect of activation temperature (850, 900 and 950 °C), activation time (30, 60, 90 and 120 min) and agent (steam and CO2) on the textural characteristics of the ACs is investigated by N2 adsorption. In general, higher activation temperatures and longer activation times increase the BET specific surface area and the porosity of the ACs, regardless of the activation agent or raw material. Steam is more reactive than CO2 in terms of pore development, especially in the case of raspberry seed cake. The performance of the ACs in liquid adsorption is evaluated by batch phenol adsorption tests. Experimental data are best fitted by the Freundlich isotherm model. Based on total yield, textural characteristics and phenol adsorption, steam activation at 900 °C for 90 min and CO2 activation at 900 °C for 120 min are found as the best activation conditions. Raspberry seed cake turns out to be a better raw material than rapeseed cake. Moreover, AC from raspberry seed cake produced by steam activation at 900 °C for 90 min performs as well as commercial AC (Norit GAC 1240) in phenol adsorption. The adsorption kinetics of the selected ACs are best fitted by the pseudo-second-order model. PMID:28773684

Moderate alcohol consumption stimulates food intake and food reward of savoury foods.

PubMed

Schrieks, Ilse C; Stafleu, Annette; Griffioen-Roose, Sanne; de Graaf, Cees; Witkamp, Renger F; Boerrigter-Rijneveld, Rianne; Hendriks, Henk F J

2015-06-01

The aim of this study was to investigate whether food reward plays a role in the stimulating effect of moderate alcohol consumption on subsequent food intake. In addition, we explored the role of oral and gut sensory pathways in alcohol's effect on food reward by modified sham feeding (MSF) or consumption of a preload after alcohol intake.In a single-blind crossover design, 24 healthy men were randomly assigned to either consumption of vodka/orange juice (20 g alcohol) or orange juice only, followed by consumption of cake, MSF of cake or no cake. Food reward was evaluated by actual food intake measured by an ad libitum lunch 45 min after alcohol ingestion and by behavioural indices of wanting and liking of four food categories (high fat, low fat, sweet and savoury).Moderate alcohol consumption increased food intake during the ad libitum lunch by 11% (+338 kJ, P = 0.004). Alcohol specifically increased intake (+127 kJ, P <0.001) and explicit liking (P = 0.019) of high-fat savoury foods. Moreover, moderate alcohol consumption increased implicit wanting for savoury (P = 0.013) and decreased implicit wanting for sweet (P = 0.017) before the meal. Explicit wanting of low-fat savoury foods only was higher after alcohol followed by no cake as compared to after alcohol followed by cake MSF (P = 0.009), but not as compared to alcohol followed by cake consumption (P = 0.082). Both cake MSF and cake consumption had no overall effect on behavioural indices of food reward.To conclude, moderate alcohol consumption increased subsequent food intake, specifically of high-fat savoury foods. This effect was related to the higher food reward experienced for savoury foods. The importance of oral and gut sensory signalling in alcohol's effect on food reward remains largely unclear. Copyright © 2015 Elsevier Ltd. All rights reserved.

Carcass characteristics and meat quality of lambs that are fed diets with palm kernel cake.

PubMed

da Conceição Dos Santos, Rozilda; Gomes, Daiany Iris; Alves, Kaliandra Souza; Mezzomo, Rafael; Oliveira, Luis Rennan Sampaio; Cutrim, Darley Oliveira; Sacramento, Samara Bianca Moraes; de Moura Lima, Elizanne; de Carvalho, Francisco Fernando Ramos

2017-06-01

The aim was to evaluate carcass characteristics, cut yield, and meat quality in lambs that were fed different inclusion levels of palm kernel cake. Forty-five woolless castrated male Santa Inês crossbred sheep with an initial average body weight of 23.16±0.35 kg were used. The experimental design was a completely randomized design with five treatments, with palm kernel cake in the proportions of 0.0%, 7.5%, 15.0%, 22.5%, and 30.0% with nine replications per treatment. After slaughter, the gastrointestinal tract was weighed when it was full, after which it was then emptied. The heart, liver, kidney, pancreas perirenal fat were also collected and weighed. The carcass was split into two identical longitudinal halves and weighed to determine the quantitative and qualitative characteristics. The empty body weight, carcass weight and yield, and fat thickness decreased linearly (p<0.05) as a function of palm kernel inclusion in the diet. There was no difference (p>0.05) for the rib eye area of animals that were fed palm kernel cake. There was a reduction in the commercial cut weight (p<0.05), except for the neck weight. The weights of the heart, liver, kidney fat, small, and large intestine, and gastrointestinal tract decreased. Nevertheless, the gastrointestinal content was greater for animals that were fed increasing levels of cake. For the other organs and viscera, differences were not verified (p>0.05). The sarcomere length decreased linearly (p<0.05), although an effect of the inclusion of palm kernel cake was not observed in other meat quality variables. It is worth noting that the red staining intensity, indicated as A, had a tendency to decrease (p = 0.050). The inclusion of palm kernel cake up to 30% in the diet does not lead to changes in meat quality characteristics, except for sarcomere length. Nevertheless, carcass quantitative characteristics decrease with the use of palm kernel cake.

Carcass characteristics and meat quality of lambs that are fed diets with palm kernel cake

PubMed Central

da Conceição dos Santos, Rozilda; Gomes, Daiany Iris; Alves, Kaliandra Souza; Mezzomo, Rafael; Oliveira, Luis Rennan Sampaio; Cutrim, Darley Oliveira; Sacramento, Samara Bianca Moraes; de Moura Lima, Elizanne; de Carvalho, Francisco Fernando Ramos

2017-01-01

Objective The aim was to evaluate carcass characteristics, cut yield, and meat quality in lambs that were fed different inclusion levels of palm kernel cake. Methods Forty-five woolless castrated male Santa Inês crossbred sheep with an initial average body weight of 23.16±0.35 kg were used. The experimental design was a completely randomized design with five treatments, with palm kernel cake in the proportions of 0.0%, 7.5%, 15.0%, 22.5%, and 30.0% with nine replications per treatment. After slaughter, the gastrointestinal tract was weighed when it was full, after which it was then emptied. The heart, liver, kidney, pancreas perirenal fat were also collected and weighed. The carcass was split into two identical longitudinal halves and weighed to determine the quantitative and qualitative characteristics. Results The empty body weight, carcass weight and yield, and fat thickness decreased linearly (p<0.05) as a function of palm kernel inclusion in the diet. There was no difference (p>0.05) for the rib eye area of animals that were fed palm kernel cake. There was a reduction in the commercial cut weight (p<0.05), except for the neck weight. The weights of the heart, liver, kidney fat, small, and large intestine, and gastrointestinal tract decreased. Nevertheless, the gastrointestinal content was greater for animals that were fed increasing levels of cake. For the other organs and viscera, differences were not verified (p>0.05). The sarcomere length decreased linearly (p<0.05), although an effect of the inclusion of palm kernel cake was not observed in other meat quality variables. It is worth noting that the red staining intensity, indicated as A, had a tendency to decrease (p = 0.050). Conclusion The inclusion of palm kernel cake up to 30% in the diet does not lead to changes in meat quality characteristics, except for sarcomere length. Nevertheless, carcass quantitative characteristics decrease with the use of palm kernel cake. PMID:27857029

Factors affecting hazardous waste solidification/stabilization: a review.

PubMed

Malviya, Rachana; Chaudhary, Rubina

2006-09-01

Solidification/stabilization is accepted as a well-established disposal technique for hazardous waste. As a result many different types of hazardous wastes are treated with different binders. The S/S products have different property from waste and binders individually. The effectiveness of S/S process is studied by physical, chemical and microstructural methods. This paper summarizes the effect of different waste stream such as heavy metals bearing sludge, filter cake, fly ash, and slag on the properties of cement and other binders. The factors affecting strength development is studied using mix designs, including metal bearing waste alters the hydration and setting time of binders. Pore structure depends on relative quantity of the constituents, cement hydration products and their reaction products with admixtures. Carbonation and additives can lead to strength improvement in waste-binder matrix.

Effect of gamma-ray irradiation on the dewaterability of waste activated sludge

NASA Astrophysics Data System (ADS)

Wu, Yuqi; Jiang, Yinghe; Ke, Guojun; Liu, Yingjiu

2017-01-01

The effect of gamma-ray irradiation on waste activated sludge (WAS) dewaterability was investigated with irradiation doses of 0-15 kGy. Time to filter (TTF50), specific resistance of filtration (SRF) and water content of sludge cake were measured to evaluate sludge dewaterability. Soluble chemical oxygen demand (SCOD), soluble extracellular polymeric substances (EPS) concentration and sludge particle size were determined to explain changes in sludge dewaterability. The optimal irradiation dose to obtain the maximum dewaterability characteristics was 1-4 kGy, which generated sludge with optimal disintegration (1.5-4.0%), soluble EPS concentration (590-750 mg/L) and particle size distribution (100-115 μm diameter). The combination of irradiation and cationic polyacrylamide (CPAM) addition exhibited minimal synergistic effect on increasing sludge dewatering rate compared with CPAM conditioning alone.

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 2 2014-07-01 2014-07-01 false Mud program. 250.1614 Section 250.1614 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... requirements concerning mud control, mud test and monitoring equipment, mud quantities, and safety precautions...

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 2 2013-07-01 2013-07-01 false Mud program. 250.1614 Section 250.1614 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... requirements concerning mud control, mud test and monitoring equipment, mud quantities, and safety precautions...

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 2 2012-07-01 2012-07-01 false Mud program. 250.1614 Section 250.1614 Mineral Resources BUREAU OF SAFETY AND ENVIRONMENTAL ENFORCEMENT, DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS... requirements concerning mud control, mud test and monitoring equipment, mud quantities, and safety precautions...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jensen, R.M.

Although use of reverse-air filters dominates in operating US utility power stations, pulse-jet designs seem to be getting the lion`s share of attention for new and retrofit plants. This article examines key technical advantages of reverse-air designs that are becoming lost in the current debate. Control of particulate emissions continues to be an area of growing concern for operators of coal-fired powerplants, especially as it relates to air toxics and fine particulates. That concern has led to greater scrutiny of the devices used to control those emissions. Regarding the fabric-filter option, reverse-air (RA) designs have operated reliably at large utilitymore » units, but now face a strong challenge from pulse-jet (PJ) designs--which are more popular with operators of independent-power-producer, waste-to-energy, and other small solid-fuel-fired units. Both RA and PJ designs can adequately meet the particulate emissions requirements for large coal-fired units when properly applied. The wholesale shift by electric utilities from RA to PJ fabric filters--at least in discussion if not actual projects--is apparent but may be short-sighted. The oft-stated reason--that RA fabric filters can only handle a face velocity one-half that of PJ, resulting in higher cost for the RA option--is too simplistic. The many design and operating characteristics that distinguish the two should be thoroughly reviewed before blanket acceptance of PJ technology. Some of the technical areas reviewed here are level of commercial design experience, bag life, pressure drop, bag replacement procedure, cleaning cycles, particle elutriation, submicron-particle floaters, residual-cake preservation, and particle re-entrainment.« less

Chemical Speciation of Chromium in Drilling Muds

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taguchi, Takeyoshi; Yoshii, Mitsuru; Shinoda, Kohzo

2007-02-02

Drilling muds are made of bentonite and other clays, and/or polymers, mixed with water to the desired viscosity. Without the drilling muds, corporations could not drill for oil and gas and we would have hardly any of the fuels and lubricants considered essential for modern industrial civilization. There are hundreds of drilling muds used and some kinds of drilling muds contain chromium. The chemical states of chromium in muds have been studied carefully due to concerns about the environmental influence. However it is difficult to determine the chemical state of chromium in drilling muds directly by conventional analytical methods. Wemore » have studied the chemical form of chromium in drilling muds by using a laboratory XAFS system and a synchrotron facility.« less

Particulate Hot Gas Stream Cleanup Technical Issues: Quarterly report, July 1-September 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pontius, D.H.

1996-12-09

This is the eighth in a series of quarterly reports describing the activities performed under Contract No. DE-AC21-94MC31160. Analyses of Hot Gas Stream Cleanup (HGCU) ashes and descriptions of filter performance address aspects of filter operation that are apparently linked to the characteristics of the collected ash or the performance of the ceramic barrier filter elements. Task 1 is designed to generate a data base of the key characteristics of ashes collected from operating advanced particle filters (APFS) and to relate these ash properties to the operation and performance of these filters. Task 2 concerns testing and failure analysis ofmore » ceramic filter elements. Under Task I during the past quarter, additional analyses were performed on ashes from the Ahlstrom 10 MWt Pressurized Fluidized Circulating Fluid Bed (PCFB) facility located at Karhula, Finland. Work continued on the HGCU data base being constructed in Microsoft Access. A variety of information has been entered into the data base, including numerical values, short or long text entries, and photographs. Detailed design of a bench top device for high temperature measurement of ash permeability has also begun. In addition to these activities, a paper was prepared and a poster was presented summarizing recent work performed under this contract at the 1996 DOE/METC Contractor`s Conference. A presentation was also given corresponding to the manuscript entitled Particle Characteristics and High-Temperature Filtration that was prepared for publication in the Proceedings of the Thirteenth Annual International Pittsburgh Coal Conference held this September in Pittsburgh, PA. Arrangements have been made to be present at the DOE/METC Modular Gas Cleanup Rig (MGCR) at the conclusion of the next run of the DOE/METC air blown Fluid Bed Gasifier (FBG). This visit will include on-site sampling to collect and characterize the filter cakes collected during FGB operation. Task 2 efforts during the past quarter focused on hoop tensile testing of Schumacher FT20 and Refractron 326 candle filter elements removed from the Karhula APF after 540 hours of service.« less

Chemical, mineralogical, and isotopic characteristics of mud from the LUSI mud volcano, Sidoarjo, East Java, Indonesia: implications for the environment, public health, and eruption processes

NASA Astrophysics Data System (ADS)

Plumlee, G. S.; Casadevall, T. J.; Wibowo, H. T.; Rosenbauer, R. J.; Johnson, C. A.; Breit, G. N.; Hageman, P. L.; Wolf, R. E.; Morman, S. A.

2009-12-01

On May 29, 2006, mud and gases began erupting from a vent 150 meters away from a gas exploration well near Sidoarjo, East Java, Indonesia. The eruption, called the LUSI mud volcano, has continued at rates as high as 160,000 m3 per day. At the request of the United States Department of State, the U.S. Geological Survey (USGS) has been providing technical assistance to the Indonesian Government on the geological and geochemical aspects of the mud eruption. This paper will present analytical results of mud samples collected in Sept. 2007 and Nov. 2008, and interpretive findings based on the analytical results. The 2007 mud sample contains high proportions of particles that could be ingestible by hand-mouth transmission (~98 vol % <250 microns,), inhalable into the upper respiratory tract (~80 vol % <10 microns), and respirable into the lung alveoli (~ 40 vol % <2.5 microns), so the mud and dust from the dried mud could be readily taken up by exposed individuals. Our results confirm those of a previous study that the levels of potentially toxic heavy metals or metalloids in the mud are low. A complex mixture of organic compounds in the mud is likely derived from petroleum source rocks. Although the 2007 mud sample contains several percent iron sulfides, net acid production tests indicate that enough carbonate material is also present to prevent the mud from becoming acid-generating due to weathering and sulfide oxidation in the near-surface environment. Water derived from settling mud deposits may have the potential to adversely affect the quality of surface- or groundwater sources for drinking water, due to high levels of fluoride, nitrate, iron, manganese, aluminum, sulfate, chloride, and total dissolved solids. The very high nitrate levels in the waters contained within the mud may present a source of nutrients that could enhance algal blooms and resulting adverse impacts such as hypoxia in fresh-water and marine ecosystems into which some of the mud is being discharged. In agreement with previous studies, water separated from the 2007 mud sample is compositionally and isotopically compatible with an origin as sedimentary formation water. The iron disulfide fraction of the mud sample is isotopically light, and likely formed by bacterial sulfate reduction during diagenesis of clay-rich rocks from which the mud was derived. A smaller, isotopically heavy monosulfide fraction likely formed later by thermogenic reduction of formation-water sulfate to sulfide and reaction of the resulting sulfide with reactive iron in the mud. Additional linked earth science and public health studies are needed to more fully understand eruption processes, and the potential environmental and health consequences of the erupting mud, waters, and gases, and of the accumulating mud deposits.

Transforming the Air Traffic Management System -- Why Is It So Hard?

DTIC Science & Technology

2012-11-08

Aircraft Systems Integration The Equity Concept Chocolate Cake Problem: How can I distribute this cake equitably among each of the students sitting...net-centric system. – Timely, common information will be available to all (humans and machines ) to help them make their decisions. – While any change...prioritization done when scarce resources must be allocated? (Remember how hard it was to distribute the chocolate cake!) ADS-B In-Trail Procedures

Geoacoustic Characterization of the Mud Drape at the New England Mud Patch

NASA Astrophysics Data System (ADS)

Reed, A. H.

2016-02-01

The New England Mud Patch is an extensive deposit of fine-grained sediments that extends from an area south of Cape Cod, MA to south of Montauk Point Long Island, NY out on the continental shelf in water depths of 60 to 90 meters. The mud patch has a remarkable accumulation of up to a 13 meter thick sequence of mud that overlays a transgressive surface of Pleistocene Age and then thins out on the periphery where surficial sediments convert from mud to sand and sand/gravel. The deposit likely accumulated in this region due to the coalescing of shelf currents that had oppositional flow. This work focuses on a section of the mud patch that is centered over the thickest portion of mud and extends east-west for 30 km and north south for 10 km. Gravity cores were collected throughout this region and the cores penetrated the upper 2-4 m of mud at 28 different sites with multiple cores collected in several locations. The mud thickness in these regions exceeded the core barrel length, therefore the cores did not penetrate into the basal sand sediment layer, a relict transgressional horizon, which displays prominently in the acoustic data for this selected region. These cores were evaluated for compressional sound speed (averaging 1480 m/s) and density (1580 kg/m3) and found to be largely homogeneous and similar throughout the study area. The largest source of inhomogeneity was due to dispersed shell hash and disarticulated bivalves, but these inclusions represent minor components in the total sediment volume. The overlying sediment that characterizes the New England Mud Patch can be readily classified as mud, silty mud, or sandy-silty mud. This fine-grained sediment deposit reflects upon the low-energy nature of the hydrodynamics within this region.

Red mud as a carbon sink: variability, affecting factors and environmental significance.

PubMed

Si, Chunhua; Ma, Yingqun; Lin, Chuxia

2013-01-15

The capacity of red mud to sequester CO(2) varied markedly due to differences in bauxite type, processing and disposal methods. Calcium carbonates were the dominant mineral phases responsible for the carbon sequestration in the investigated red mud types. The carbon sequestration capacity of red mud was not fully exploited due to shortages of soluble divalent cations for formation of stable carbonate minerals. Titanate and silicate ions were the two major oxyanions that appeared to strongly compete with carbonate ions for the available soluble Ca. Supply of additional soluble Ca and Mg could be a viable pathway for maximizing carbon sequestration in red mud and simultaneously reducing the causticity of red mud. It is roughly estimated that over 100 million tonnes of CO(2) have been unintentionally sequestered in red mud around the world to date through the natural weathering of historically produced red mud. Based on the current production rate of red mud, it is likely that some 6 million tonnes of CO(2) will be sequestered annually through atmospheric carbonation. If appropriate technologies are in place for incorporating binding cations into red mud, approximately 6 million tonnes of additional CO(2) can be captured and stored in the red mud while the hazardousness of red mud is simultaneously reduced. Copyright © 2012 Elsevier B.V. All rights reserved.

Shallow-Water Mud Acoustics

DTIC Science & Technology

2015-09-30

1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Shallow- Water Mud Acoustics William L. Siegmann...shallow water over mud sediments and of acoustic detection, localization, and classification of objects buried in mud. OBJECTIVES • Develop...including long-range conveyance of information; detection, localization, and classification of objects buried in mud; and improvement of shallow water

46 CFR 128.450 - Liquid-mud systems.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Liquid-mud systems. 128.450 Section 128.450 Shipping...: EQUIPMENT AND SYSTEMS Design Requirements for Specific Systems § 128.450 Liquid-mud systems. (a) Liquid-mud... this chapter. (b) Tanks for oil-based liquid mud must be fitted with tank vents equipped with flame...

Binding of Vapour-Phase Mercury (Hg0) on Chemically Treated Bauxite Residues (Red Mud)

EPA Science Inventory

In this study, Hg capture using red mud, seawater-neutralized red mud, and acid-treated red mud is evaluated and compared to other, more conventional sorbent materials. Red mud (also known as bauxite residue) is a by-product of extracting alumina from ground bauxite ore by treati...

[Aconite cake-separated moxibustion for knee osteoarthritis with kidney-marrow deficiency].

PubMed

Chen, Meiren; Hu, Rong; Lin, Jian; Huang, Yuhui; Mao, Wanping; Wen, Yuanying; Dai, Gaole

2018-01-12

To observe the effects among aconite cake-separated moxibustion, moxibustion and acupuncture for knee osteoarthritis (KOA) with kidney-marrow deficiency and to explore the feasibility of cake-separated moxibustion as a home remedy solution. Ninety patients were randomized into an aconite cake-separated moxibustion group, a moxibustion group and an acupuncture group, 30 cases in each one. The acupoints in the three groups were Neixiyan (EX-LE 4), Dubi (ST 35) in the affected side, and bilateral Xuehai (SP 10), Liangqiu (ST 34), Heding (EX-LE 2), Shenshu (BL 23) and Zusanli (ST 36). All the treatment was given for 3 sessions, 10 days as a session with 2 to 3 days between 2 sessions, and once a day. The first 2 courses of aconite cake-separated moxibustion was applied in the hospital and the other 1 session was used at home guided by officer physician. Symptoms and physical signs classification score and life quality scores were recorded before and after treatment and 6 months after treatment, including walking pain, knee pain in stoop and squat, knee discomfort in stair activity and daily discomfort. The effects were evaluated. The symptoms and physical signs classification scores in the three groups after treatment and at follow-up were lower than those before treatment ( P <0.01, P <0.05), and the scores in the aconite cake-separated moxibustion group were better than those in the moxibustion group and acupuncture group (all P <0.01). The scores of walking pain, knee pain in stoop and squat, knee discomfort in stair activity and daily discomfort were lower in the three groups after treatment and 6 months after treatment ( P <0.01, P <0.05), and the scores of walking pain and daily discomfort in the aconite cake-separated moxibustion group were lower than those in the moxibustion group and acupuncture group ( P <0.01, P <0.05). After treatments, the cured and markedly effective rate in the aconite cake-separated moxibustion group was 63.3% (19/30); that in the moxibustion group was 50.0% (15/30) and one in the acupuncture group was 43.3% (13/30). The cured and markedly effective rate of aconite cake-separated moxibustion group was more promising than those in the other two groups (both P <0.05). At follow-up, the cured and markedly effective rate in the aconite cake-separated moxibustion group was 56.7% (17/30), which was better than 36.7% (11/30) in the moxibustion group and 40.0% (12/30) in the acupuncture group (both P <0.05). Aconite cake-separated moxibustion can be used for KOA patients with kidney-marrow deficiency, which can improve patients' life quality and is better than moxibustion and acupuncture. The method is feasible as a home remedy solution.

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614... shall comply with requirements concerning mud control, mud test and monitoring equipment, mud quantities...

Recycling red mud from the production of aluminium as a red cement-based mortar.

PubMed

Yang, Xiaojie; Zhao, Jianfeng; Li, Haoxin; Zhao, Piqi; Chen, Qin

2017-05-01

Current management for red mud is insufficient and a new method is needed. A series of experiments have been carried out to develop a new approach for effective management of red mud. Mortars without or with 3%, 6% and 9% red mud were prepared and their fresh and hardened properties were measured to access the possibility of recycling the red mud in the production of red cement-based mortar. The mechanisms corresponding to their mechanical performance variations were explored by X-ray powder diffraction and scanning electron microscopy. The results show that the fresh mortars with red mud present an increase of viscosity as compared with the control. However, little difference is found when the content of red mud is altered. It also can be seen that red mud increases flow time and reduces the slump flow of the mortar. Meanwhile, it is found that mortar with red mud is provided with higher air content. Red mud is eligible to adjust the decorative mortar colour. Compressive strength of mortar is improved when less than 6% red mud is added. However, overall it has a slightly negative effect on tensile bond strength. It decreases the Ca(OH) 2 content and densifies the microstructure of hardened paste. The heavy metal concentrations in leachates of mortars with red mud are much lower than the values required in the standard, and it will not do harm to people's health and the environment. These results are important to recycle and effectively manage red mud via the production of red cement-based mortar.

Hidden values in bauxite residue (red mud): Recovery of metals

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Yanju; Naidu, Ravi, E-mail: ravi.naidu@unisa.edu.au

Highlights: • Current iron recovery techniques using red mud are depicted. • Advantages and disadvantages exist in different recovering processes. • Economic and environmental friendly integrated usage of red mud is promising. - Abstract: Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially.more » Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud.« less

Linking geochemical processes in mud volcanoes with arsenic mobilization driven by organic matter.

PubMed

Liu, Chia-Chuan; Kar, Sandeep; Jean, Jiin-Shuh; Wang, Chung-Ho; Lee, Yao-Chang; Sracek, Ondra; Li, Zhaohui; Bundschuh, Jochen; Yang, Huai-Jen; Chen, Chien-Yen

2013-11-15

The present study deals with geochemical characterization of mud fluids and sediments collected from Kunshuiping (KSP), Liyushan (LYS), Wushanting (WST), Sinyangnyuhu (SYNH), Hsiaokunshui (HKS) and Yenshuikeng (YSK) mud volcanoes in southwestern Taiwan. Chemical constituents (cations, anions, trace elements, organic carbon, humic acid, and stable isotopes) in both fluids and mud were analyzed to investigate the geochemical processes and spatial variability among the mud volcanoes under consideration. Analytical results suggested that the anoxic mud volcanic fluids are highly saline, implying connate water as the probable source. The isotopic signature indicated that δ(18)O-rich fluids may be associated with silicate and carbonate mineral released through water-rock interaction, along with dehydration of clay minerals. Considerable amounts of arsenic in mud irrespective of fluid composition suggested possible release through biogeochemical processes in the subsurface environment. Sequential extraction of As from the mud indicated that As was mostly present in organic and sulphidic phases, and adsorbed on amorphous Mn oxyhydroxides. Volcanic mud and fluids are rich in organic matter (in terms of organic carbon), and the presence of humic acid in mud has implications for the binding of arsenic. Functional groups of humic acid also showed variable sources of organic matter among the mud volcanoes being examined. Because arsenate concentration in the mud fluids was found to be independent from geochemical factors, it was considered that organic matter may induce arsenic mobilization through an adsorption/desorption mechanism with humic substances under reducing conditions. Organic matter therefore plays a significant role in the mobility of arsenic in mud volcanoes. Copyright © 2012 Elsevier B.V. All rights reserved.

Study on dealkalization and settling performance of red mud.

PubMed

Luo, Muxi; Qi, Xuejiao; Zhang, Yurui; Ren, Yufei; Tong, Jiacheng; Chen, Zining; Hou, Yiming; Yeerkebai, Nuerxiate; Wang, Hongtao; Feng, Shijin; Li, Fengting

2017-01-01

At present, the dealkalization and comprehensive utilization of red mud is a worldwide problem. Studies on the settling performance and phase transformation of red mud by HCl, CaO, and H 2 O leaching are limited. In this study, the characteristics of red mud were systematically analyzed. The average sizes of graded and initial red mud were 4.11 and 9.20 μm, respectively. X-ray diffraction (XRD), X-ray fluorescence spectra (XRF), and thermogravimetry-differential scanning calorimetry (TG-DSC) results indicated the different mineralogical phases, composition, and thermal behavior. The addition of HCl could neutralize the alkalization in the red mud slurry, and CaO could replace the Na and K. Notably, the pH of the red mud slurry had no obvious change with the increase in water washing times in a certain pH. Interestingly, soluble Al and Fe were not detected in the HCl-red mud and CaO-red mud. In addition, the settling ratio was used to express the settling performance of the red mud slurry. Their interaction mechanisms were proposed, which may include phase transformation and the changing of the size and surface area. The research provided a better understanding of the phase transformation and settling performance in the treatment of red mud by HCl, CaO, and H 2 O leaching.

The use of red mud as an immobiliser for metal/metalloid-contaminated soil: A review.

PubMed

Hua, Yumei; Heal, Kate V; Friesl-Hanl, Wolfgang

2017-03-05

This review focuses on the applicability of red mud as an amendment for metal/metalloid-contaminated soil. The varying properties of red muds from different sources are presented as they influence the potentially toxic element (PTE) concentration in amended soil. Experiments conducted worldwide from the laboratory to the field scale are screened and the influencing parameters and processes in soils are highlighted. Overall red mud amendment is likely to contribute to lowering the PTE availability in contaminated soil. This is attributed to the high pH, Fe and Al oxide/oxyhydroxide content of red mud, especially hematite, boehmite, gibbsite and cancrinite phases involved in immobilising metals/metalloids. In most cases red mud amendment resulted in a lowering of metal concentrations in plants. Bacterial activity was intensified in red mud-amended contaminated soil, suggesting the toxicity from PTEs was reduced by red mud, as well as indirect effects due to changes in soil properties. Besides positive effects of red mud amendment, negative effects may also appear (e.g. increased mobility of As, Cu) which require site-specific risk assessments. Red mud remediation of metal/metalloid contaminated sites has the potential benefit of reducing red mud storage and associated problems. Copyright © 2016 Elsevier B.V. All rights reserved.

Efficiency of baited hoop nets for sampling catfish in southeastern U.S. small impoundments

USGS Publications Warehouse

Wallace, Benjamin C.; Weaver, Daniel M.; Kwak, Thomas J.

2011-01-01

Many U.S. natural resource agencies stock catfish (Ictaluridae) into small impoundments to provide recreational fishing opportunities. However, effective standardized methods for sampling catfish in small impoundments have not been developed for wide application, particularly in the southeastern United States. We evaluated the efficiency of three bait treatments (i.e., soybean cake, sunflower cake, and no bait) of tandem hoop nets in two North Carolina small impoundments during the fall of 2008 and spring of 2009 in a factorial experimental design. The impoundments were stocked with catchable-size channel catfish Ictalurus punctatus at contrastingly low (5.5 fi sh/ha) and high (90.0 fi sh/ha) rates prior to our sampling. Nets baited with soybean cake consistently sampled more channel catfish than any other treatment. Channel catfish catch ranged as high as 3,251 fi sh per net series during the fall in nets baited with soybean cake in the intensively stocked impoundment and was up to 8.5 and 15.3 times higher during the fall than in the spring in each impoundment. Nets baited with soybean cake sampled significantly (12 and 24 times) more channel catfish than those with no bait in the two impoundments. These trends did not occur among other catfish species. Nonictalurid fish and turtle catch was higher during spring compared to that of fall, corresponding with low channel catfish catches. Our results indicate that tandem hoop nets baited with soybean cake during the fall is a more efficient method for sampling channel catfish compared to nets baited with sunflower cake or no bait in spring or fall. Our findings validate this technique for application in southeastern U.S. small impoundments to assess catfish abundance to guide management and evaluate the success of catfish stocking programs.

Aflatoxin levels in sunflower seeds and cakes collected from micro- and small-scale sunflower oil processors in Tanzania.

PubMed

Mmongoyo, Juma A; Wu, Felicia; Linz, John E; Nair, Muraleedharan G; Mugula, Jovin K; Tempelman, Robert J; Strasburg, Gale M

2017-01-01

Aflatoxin, a mycotoxin found commonly in maize and peanuts worldwide, is associated with liver cancer, acute toxicosis, and growth impairment in humans and animals. In Tanzania, sunflower seeds are a source of snacks, cooking oil, and animal feed. These seeds are a potential source of aflatoxin contamination. However, reports on aflatoxin contamination in sunflower seeds and cakes are scarce. The objective of the current study was to determine total aflatoxin concentrations in sunflower seeds and cakes from small-scale oil processors across Tanzania. Samples of sunflower seeds (n = 90) and cakes (n = 92) were collected across two years, and analyzed for total aflatoxin concentrations using a direct competitive enzyme-linked immunosorbent assay (ELISA). For seed samples collected June-August 2014, the highest aflatoxin concentrations were from Dodoma (1.7-280.6 ng/g), Singida (1.4-261.8 ng/g), and Babati-Manyara (1.8-162.0 ng/g). The highest concentrations for cakes were from Mbeya (2.8-97.7 ng/g), Dodoma (1.9-88.2 ng/g), and Singida (2.0-34.3 ng/g). For seed samples collected August-October 2015, the highest concentrations were from Morogoro (2.8-662.7 ng/g), Singida (1.6-217.6 ng/g) and Mbeya (1.4-174.2 ng/g). The highest concentrations for cakes were from Morogoro (2.7-536.0 ng/g), Dodoma (1.4-598.4 ng/g) and Singida (3.2-52.8 ng/g). In summary, humans and animals are potentially at high risk of exposure to aflatoxins through sunflower seeds and cakes from micro-scale millers in Tanzania; and location influences risk.

Acceptance and purchase intent of US consumers for nonwheat rice butter cakes.

PubMed

Sae-Eaw, A; Chompreeda, P; Prinyawiwatkul, W; Haruthaithanasan, V; Suwonsichon, T; Saidu, J E; Xu, Z

2007-03-01

This study evaluated consumer acceptance and purchase intent of nonwheat butter cake formulations prepared with Thai jasmine rice flour. Three nonwheat rice butter cakes were prepared with varying amounts of powdered emulsifier (propylene glycol ester:diacetyl tartaric acid ester of monoglyceride, 8:2) at 0% (product A), 7.5% (product B), and 15% (product C) of the margarine content (15%) in the cake formulation. A commercial wheat-based butter cake served as the control. Consumers (n= 400) evaluated acceptability of 9 sensory attributes using a 9-point hedonic scale. Overall acceptance and purchase intent were determined with a binomial (yes/no) scale. At least 81% of consumers accepted products B and C, of which 42.1% and 47%, respectively, would purchase the products if commercially available. Product A was neither liked nor disliked with an overall liking score of 5.39. The butter cake products were differentiated by textural acceptability (overall texture, softness, and moistness) with a canonical correlation of 0.71 to 0.79. Overall liking and taste influenced overall acceptance and purchase intent. Odor influenced purchase intent (P= 0.0014), but not overall acceptance. The odds ratio of overall liking was 3.462 for purchase intent, indicating the probability of the product being purchased is 3.462 times higher (than not being purchased, P < 0.0001) with every 1-unit increase of the overall liking score. Based on the logit model, overall acceptance and purchase intent could be predicted with 89.3% and 83.3% accuracy, respectively. The study demonstrated feasibility of completely substituting wheat flour with Thai jasmine rice flour for production of butter cake products acceptable to American consumers.

Process for treating moisture laden coal fines

DOEpatents

Davis, Burl E.; Henry, Raymond M.; Trivett, Gordon S.; Albaugh, Edgar W.

1993-01-01

A process is provided for making a free flowing granular product from moisture laden caked coal fines, such as wet cake, by mixing a water immiscible substance, such as oil, with the caked coal, preferably under low shear forces for a period of time sufficient to produce a plurality of free flowing granules. Each granule is preferably comprised of a dry appearing admixture of one or more coal particle, 2-50% by weight water and the water immiscible substance.

Canola Cake as a Potential Substrate for Proteolytic Enzymes Production by a Selected Strain of Aspergillus oryzae: Selection of Process Conditions and Product Characterization

PubMed Central

Freitas, Adriana C.; Castro, Ruann J. S.; Fontenele, Maria A.; Egito, Antonio S.; Farinas, Cristiane S.; Pinto, Gustavo A. S.

2013-01-01

Oil cakes have excellent nutritional value and offer considerable potential for use in biotechnological processes that employ solid-state fermentation (SSF) for the production of high value products. This work evaluates the feasibility of using canola cake as a substrate for protease production by a selected strain of Aspergillus oryzae cultivated under SSF. The influences of the following process parameters were considered: initial substrate moisture content, incubation temperature, inoculum size, and pH of the buffer used for protease extraction and activity analysis. Maximum protease activity was obtained after cultivating Aspergillus oryzae CCBP 001 at 20°C, using an inoculum size of 107 spores/g in canola cake medium moistened with 40 mL of water to 100 g of cake. Cultivation and extraction under selected conditions increased protease activity 5.8-fold, compared to the initial conditions. Zymogram analysis of the enzymatic extract showed that the protease molecular weights varied between 31 and 200 kDa. The concentrated protease extract induced clotting of casein in 5 min. The results demonstrate the potential application of canola cake for protease production under SSF and contribute to the technological advances needed to increase the efficiency of processes designed to add value to agroindustrial wastes. PMID:24455400

Quantitative evaluation method of the bubble structure of sponge cake by using morphology image processing

NASA Astrophysics Data System (ADS)

Tatebe, Hironobu; Kato, Kunihito; Yamamoto, Kazuhiko; Katsuta, Yukio; Nonaka, Masahiko

2005-12-01

Now a day, many evaluation methods for the food industry by using image processing are proposed. These methods are becoming new evaluation method besides the sensory test and the solid-state measurement that are using for the quality evaluation. An advantage of the image processing is to be able to evaluate objectively. The goal of our research is structure evaluation of sponge cake by using image processing. In this paper, we propose a feature extraction method of the bobble structure in the sponge cake. Analysis of the bubble structure is one of the important properties to understand characteristics of the cake from the image. In order to take the cake image, first we cut cakes and measured that's surface by using the CIS scanner. Because the depth of field of this type scanner is very shallow, the bubble region of the surface has low gray scale values, and it has a feature that is blur. We extracted bubble regions from the surface images based on these features. First, input image is binarized, and the feature of bubble is extracted by the morphology analysis. In order to evaluate the result of feature extraction, we compared correlation with "Size of the bubble" of the sensory test result. From a result, the bubble extraction by using morphology analysis gives good correlation. It is shown that our method is as well as the subjectivity evaluation.

Improvement of texture and sensory properties of cakes by addition of potato peel powder with high level of dietary fiber and protein.

PubMed

Ben Jeddou, Khawla; Bouaziz, Fatma; Zouari-Ellouzi, Soumaya; Chaari, Fatma; Ellouz-Chaabouni, Semia; Ellouz-Ghorbel, Raoudha; Nouri-Ellouz, Oumèma

2017-02-15

Demand for health oriented products such as low calories and high fiber product is increasing. The aim of the present work was to determine the effect of the addition of potato peel powders as protein and dietary fiber source on the quality of the dough and the cake. Powders obtained from the two types of peel flour showed interesting water binding capacity and fat absorption capacity. Potato peel flours were incorporated in wheat flours at different concentration. The results showed that peel powders additionally considerably improved the Alveograph profile of dough and the texture of the prepared cakes. In addition color measurements showed a significant difference between the control dough and the dough containing potato peels. The replacement of wheat flour with the potato powders reduced the cake hardness significantly and the L(*) and b(*) dough color values. The increased consumption of cake enriched with potato peel fiber is proposed for health reasons. The study demonstrated that protein/fiber-enriched cake with good sensory quality could be produced by the substitution of wheat flour by 5% of potato peel powder. In addition and technological point of view, the incorporation of potato peel powder at 5% increase the dough strength and elasticity-to-extensibility ratio (P/L). Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Bilberry and bilberry press cake as sources of dietary fibre

PubMed Central

Aura, Anna-Marja; Holopainen-Mantila, Ulla; Sibakov, Juhani; Kössö, Tuija; Mokkila, Mirja; Kaisa, Poutanen

2015-01-01

Background Dietary recommendations for Nordic countries urge the use of plant foods as a basis for healthy nutrition. Currently, the level of dietary fibre (DF) intake is not adequate. Berries are an elementary part of the recommended Nordic healthy diet and could be consumed in higher amounts. Materials and methods Finnish bilberries and a bilberry press cake from juice processing were studied for DF content, carbohydrate composition, and non-carbohydrate fibre content, which was analysed as sulphuric acid insoluble and soluble material. The microstructure of all samples was also studied using light microscopy and toluidine blue O, calcofluor, and acid fuchsin staining. Results The total DF contents of fresh and freeze-dried bilberries and the press cake were 3.0, 24.1, and 58.9%, respectively. Most of the DF was insoluble. Only about half of it was carbohydrate, the rest being mostly sulphuric acid–insoluble material, waxy cutin from skins, and resilient seeds. Bilberry seeds represented over half of the press cake fraction, and in addition to skin, they were the major DF sources. Microscopy revealed that skins in the press cake were intact and the surface of the seeds had thick-walled cells. Conclusions Bilberry press cake is thus a good source of insoluble non-carbohydrate DF, and could be used to provide DF-rich foods to contribute to versatile intake of DF. PMID:26652738

Evaluation of the effectiveness of olive cake residue as an expansive soil stabilizer

NASA Astrophysics Data System (ADS)

Nalbantoglu, Zalihe; Tawfiq, Salma

2006-08-01

The quantity of the by-product olive cake residue generated in most parts of the Mediterranean countries continues to increase and expected to double in amount within 10 15 years. This increase intensifies the problems associated with the disposal of this by-product. Olive cake residue has a potential for use as a soil stabilizer and large volumes can be beneficially used. This study is directed toward determining if olive cake residue can be utilized to increase the strength and stability of expansive soils which constitute a costly natural hazard to lightweight structures on shallow foundations. A series of laboratory tests using engineering properties, such as Atterberg limits, moisture-density relationship (compaction), swell, unconfined compressive strength were undertaken to evaluate the effectiveness and performance of the olive cake residue as a soil stabilizer. Test results indicate that an addition of only 3% burned olive waste into the soil causes a reduction in plasticity, volume change and an increase in the unconfined compressive strength. However, it was observed that the presence of burned olive waste in the soil greater than 3% caused an increase in the compressibility and a decrease in the unconfined compressive strength. Test results indicate that the use of olive waste in soil stabilization gives greater benefits to the environment than simply disposing of the by-product, olive cake residue.

[Improvement of municipal sewage sludge dewaterability by bioleaching: a pilot-scale study with sequence batch reaction model].

PubMed

Liu, Fen-Wu; Zhou, Li-Xiang; Zhou, Jun; Jiang, Feng; Wang, Dian-Zhan

2011-07-01

To observe the bioleaching effect on sewage sludge dewaterability, three consecutive batch bioleaching experiments were conducted through a bioleaching bio-reactor with 700 L of working volume. Subsequently, the bioleached sludge was dewatered by using chamber filter press. The results show that the 1st batch bioleaching process can be finished within 90 hours if the aeration amount was 1.2 m3/h with the 1: 15 mixing ratio of bioleached sludge to raw sludge. The pH of sludge declines from initial 6.11 to 2.33 while ORP increased from initial -134 mV to finial 507 mV. The specific resistance to filtration (SRF) of the tested sludge was decreased from original 1.00 x 10(13) m/kg to final 0.09 x 10(13) m/kg after bioleaching. For the subsequent two batch trials, the bioleaching process can be finished in 40 hours and 46 hours, respectively. Likewise, sludge SRF is also significantly decreased to 0.19 x 10(13) m/kg and 0.36 x 10(13) m/kg if the mixing ratio of bioleached sludge to fresh sludge is 1:1 although the microbial nutrient substance dosage is reduced by 25% and 50% for 2nd, and 3rd batch experiments, respectively. The harvested bioleached sludge from three batch trails is dewatered by chamber filter press with 0.3-0.4 MPa working pressure for 2 hours. It is found that the moisture of dewatered sludge cake can be reduced to 58%, and that the dewatered sludge cake is of khaki appearance and didn't emit any offensive odor. In addition, it is also observes that sludge organic matter only changed a bit from 52.9% to 48.0%, but 58% of sludge-borne Cu and 88% of sludge-borne Zn can be removed from sludge by bioleaching process. Therefore, dual goals for sludge-borne heavy metal removal and sludge dewatering of high efficiency can be achieved simultaneously through the approach mentioned above. Therefore, bioleaching technique is of great engineering application for the treatment of sewage sludge.

Effects of medicinal cake-separated moxibustion on plasma 6-keto-PGF1alpha and TXB2 contents in the rabbit of hyperlipemia.

PubMed

Xiaorong, Chang; Jie, Yan; Zenghui, Yue; Jing, Shen; Yaping, Lin; Shouxiang, Yi; Xiangping, Cao

2005-06-01

Hyperlipemia rabbit models established with high cholesterol and fat diet were treated with direct moxibustion and medicinal cake-separated moxibustion. The post-treatment plasma 6-keto-prostaglandin F1alpha (6-keto-PGF1alpha) and thromboxane B2 (TXB2) contents were determined by radioimmunoassay. Results indicated that the plasma 6-keto-PGF1alpha content significantly increased, the TXB2 level decreased (P < 0.05) and the TXB2 /6-keto-PGF1alpha ratio also decreased (P < 0.01) in the medicinal cake-separated moxibustion group as compared with those in the model group respectively, but there was no significant difference between the medicinal cake-separated moxibustion group and the direct moxibustion group (P > 0.05), suggesting that both the medicinal cake-separated moxibustion and direct moxibustion can regulate the plasma 6-keto-PGF1alpha and TXB2 contents, and the TXB2/6-keto-PGF1alpha ratio with similar actions, and have a certain protective action on endothelial cells of the aorta in the rabbit of hyperlipemia.

Commercial cuts and chemical and sensory attributes of meat from crossbred Boer goats fed sunflower cake-based diets.

PubMed

Oliveira, Ronaldo Lopes; Palmieri, Adriana Dantas; Carvalho, Silvana Teixeira; Leão, André Gustavo; de Abreu, Claudilene Lima; Ribeiro, Claudio Vaz Di Mambro; Pereira, Elzania Sales; de Carvalho, Gleidson Giordano Pinto; Bezerra, Leilson Rocha

2015-05-01

This study aimed to evaluate sunflower cake feed in commercial cut yields and chemical and sensory attributes of goat meat. Thirty-two castrated male goats were distributed in four levels (0, 8, 16 and 24%) of sunflower cake supplementation. The animals were slaughtered and the carcasses were placed in a cold chamber and sectioned into five anatomical regions corresponding to commercial cuts. Samples of the Longissimus lumborum muscle were analyzed for chemical composition and sensory quality. The chemical composition and pH were not affected by the treatments. The smell, taste and 'goatiness' of the aroma and flavor of the meat were also unaffected by the treatments. The appearance, tenderness and juiciness of the meat differed by treatment. The highest level (24%) of sunflower cake increased meat tenderness; however, according to the tasters there was reduced softness, although none of the samples were rejected by the tasters. Sunflower cake can be added to the diet at a level of up to 16% without altering the quantitative and qualitative attributes of the meat. © 2014 Japanese Society of Animal Science.

Impact of diverse cultivars on molecular and crystalline structures of rice starch for food processing.

PubMed

Lee, Seul; Lee, Ju Hun; Chung, Hyun-Jung

2017-08-01

The objective of this study was to determine the molecular and crystalline structures of starches from diverse rice cultivars for three major food processing in Korea (cooked rice, brewing and rice cake). Rice starches were isolated from 10 different rice varieties grown in Korea. Apparent amylose contents of rice starches from cooked rice, brewing and rice cake varieties were 21.1-22.4%, 22.9-24.6%, and 20.1-22.0%, respectively. Rice starches from rice cake varieties showed higher peak viscosity but lower pasting temperature than those from cooked rice and brewing varieties. Swelling factor at 80°C of rice starches from cooked rice, brewing and rice cake varieties was 16.6-19.0, 17.8-19.3, and 17.8-19.2, respectively. Based on structure and physicochemical properties of rice starches extracted from different rice varieties, principal component analysis (PCA) results showed that these rice varieties could be clearly classified according to processing adaptability for cooked rice and rice cake. Copyright © 2017 Elsevier Ltd. All rights reserved.

Oil cakes - a by-product of agriculture industry as a fortificant in bakery products.

PubMed

Behera, Satyabadi; Indumathi, K; Mahadevamma, S; Sudha, M L

2013-11-01

Groundnut cake (GNC) and soybean cake (SBC) by-product of agriculture industry had protein and protein digestibility in the range of 42.7-50.5 and 71.3-76.8%, respectively. Polyphenols present in GNC and SBC were cholorogenic acid, syringic acid and p-coumaric acid. The number of bands separated in soybean meal was greater than the bands observed in GNC flour as seen in SDS-PAGE pattern, respectively. SEM of groundnut flour showed distension of protein bodies due to roasting of the oil cakes. The water absorption of wheat flour GNC blends decreased from 59.2 to 57.3% and increased in wheat flour SBC blends from 59.2 to 68.3% with an increase in oil cake from 0 to 20%. With increase in either GNC or SBC, the biscuits became harder. Addition of glycerol monostearate and sodium stearoyl lactylate in combination with 20% blend of GNC/SBC decreased the breaking strength values and increased the sensory parameters of the biscuits. Nutritionally rich biscuits were thus prepared by incorporating GNC/SBC.

Amino acid composition and biological effects of supplementing broad bean and corn proteins with Nigella sativa (black cumin) cake protein.

PubMed

al-Gaby, A M

1998-10-01

The biological effects of supplementing broad bean (Vicia faba) or corn (Zea maize) meal protein with black cumin (Nigella sativa) cake protein as well as their amino acid composition were investigated. The percentage of total protein content of Nigella cake was 22.7%. Lysine is existent in abundant amounts in faba meal protein, while leucine is the most abundant in corn meal protein (chemical score = 156) and valine is higher in Nagella cake protein. compared with rats fed sole corn or faba meal protein, substitution of 25% of corn or faba meal protein with Nigella cake protein in the diet remarkably raised the growth rate of rats and resulted in significant higher levels of rat total serum lipids and triglycerides. Also, the supplemented diet caused significant increases in serum total protein and its two fractions albumin and globulin and insignificantly increase the activity of serum phosphatases and transaminases within normal ranges. The supplementation did not have any adverse nutritional effects in the levels of lipid fractions in the serum.

Fermentation process improvement of a Chinese traditional food: soybean residue cake.

PubMed

Yao, Yingzheng; Pan, Siyi; Wang, Kexing; Xu, Xiaoyun

2010-09-01

Fermentation process improvement of soybean residue cake, a Chinese traditional fermented food, and its physicochemical analysis during fermentation were studied. One of the dominant strains in the fermentation was isolated and identified as Mucor racemosus Fresenius. The fermentation process was improved by subsection fermentation. The crude protein content decreased from 19.95 ± 0.03% in the raw soybean residue to 16.85 ± 0.10% in the fermented products, and the formaldehyde nitrogen content increased from 0.068 ± 0.004% to 0.461 ± 0.022% in final fermented cakes. Hardness of samples significantly (P < 0.05) increased whereas springiness, cohesiveness, and resilience significantly (P < 0.05) decreased with increasing fermentation time, respectively. Microstructure observations showed obvious change of the surface of cake samples during the fermentation process. During the soybean processing, it will produce plenty of by-products, and the most part of them is soybean residue. The discarded soybean residue causes economic loss. Fortunately, we can obtain nutritious and delicious fermented soybean residue cakes by fermenting soybean residue as raw material.

Water reduction in waste-activated sludge by resettling and filtration in batch. Phase (1): pilot-scale experiments to optimize performance.

PubMed

Trapote, Arturo; Jover, Margarita; Cartagena, Pablo; El Kaddouri, Marouane; Prats, Daniel

2014-08-01

This article describes an effective procedure for reducing the water content of excess sludge production from a wastewater treatment plant by increasing its concentration and, as a consequence, minimizing the volume of sludge to be managed. It consists of a pre-dewatering sludge process, which is used as a preliminary step or alternative to the thickening. It is made up of two discontinuous sequential stages: the first is resettling and the second, filtration through a porous medium. The process is strictly physical, without any chemical additives or electromechanical equipment intervening. The experiment was carried out in a pilot-scale system, consisting of a column of sedimentation that incorporates a filter medium. Different sludge heights were tested over the filter to verify the influence ofhydrostatic pressure on the various final concentrations of each stage. The results show that the initial sludge concentration may increase by more than 570% by the end of the process with the final volume of sludge being reduced in similar proportions and hydrostatic pressure having a limited effect on this final concentration. Moreover, the value of the hydrostatic pressure at which critical specific cake resistance is reached is established.

Apparatus for photocatalytic treatment of liquids

NASA Technical Reports Server (NTRS)

Cooper, Gerald (Inventor); Ratcliff, Matthew A. (Inventor)

1992-01-01

Apparatus for decontaminating a contaminated fluid by using photocatalytic particles. The apparatus includes a reactor tank for holding a slurry of the contaminated fluid and the photocatalytic particles ultraviolet light irradiates the surface of the slurry, thereby activating the photocatalytic properties of the particles. Stirring blades for continuously agitate the irradiated fluid surface maintaining the particles in a suspended state within the fluid. A cross flow filter is used for separating the fluid from the semiconductor powder after the decomposition reaction is ended. The cross flow filter is occasionally back flushed to remove any caked semiconductor powder. The semiconductor powder may be recirculated back to the tank for reuse, or may be stored for future use. A series of reactor tanks may be used to gradually decompose a chemical in the fluid. The fluid may be pretreated to remove certain metal ions which interfere with the photocatalytic process. Such pretreatment may be accomplished by dispersing semiconductor particles within the fluid, which particles adsorb ions or photodeposit the metal as the free metal or its insoluble oxide or hydroxide, and then removing the semiconductor particles together with the adsorbed metal ions/oxides/hydroxide/free metal from the fluid.

Environmental dust effects on aluminum surfaces in humid air ambient.

PubMed

Yilbas, Bekir Sami; Hassan, Ghassan; Ali, Haider; Al-Aqeeli, Nasser

2017-04-05

Environmental dusts settle on surfaces and influence the performance of concentrated solar energy harvesting devices, such as aluminum troughs. The characteristics of environmental dust and the effects of mud formed from the dust particles as a result of water condensing in humid air conditions on an aluminum wafer surface are examined. The dissolution of alkaline and alkaline earth compounds in water condensate form a chemically active mud liquid with pH 8.2. Due to gravity, the mud liquid settles at the interface of the mud and the aluminum surface while forming locally scattered patches of liquid films. Once the mud liquid dries, adhesion work to remove the dry mud increases significantly. The mud liquid gives rise to the formation of pinholes and local pit sites on the aluminum surface. Morphological changes due to pit sites and residues of the dry mud on the aluminum surface lower the surface reflection after the removal of the dry mud from the surface. The characteristics of the aluminum surface can address the dust/mud-related limitations of reflective surfaces and may have implications for the reductions in the efficiencies of solar concentrated power systems.

Environmental dust effects on aluminum surfaces in humid air ambient

PubMed Central

Yilbas, Bekir Sami; Hassan, Ghassan; Ali, Haider; Al-Aqeeli, Nasser

2017-01-01

Environmental dusts settle on surfaces and influence the performance of concentrated solar energy harvesting devices, such as aluminum troughs. The characteristics of environmental dust and the effects of mud formed from the dust particles as a result of water condensing in humid air conditions on an aluminum wafer surface are examined. The dissolution of alkaline and alkaline earth compounds in water condensate form a chemically active mud liquid with pH 8.2. Due to gravity, the mud liquid settles at the interface of the mud and the aluminum surface while forming locally scattered patches of liquid films. Once the mud liquid dries, adhesion work to remove the dry mud increases significantly. The mud liquid gives rise to the formation of pinholes and local pit sites on the aluminum surface. Morphological changes due to pit sites and residues of the dry mud on the aluminum surface lower the surface reflection after the removal of the dry mud from the surface. The characteristics of the aluminum surface can address the dust/mud-related limitations of reflective surfaces and may have implications for the reductions in the efficiencies of solar concentrated power systems. PMID:28378798

Influence of red mud on soil microbial communities: Application and comprehensive evaluation of the Biolog EcoPlate approach as a tool in soil microbiological studies.

PubMed

Feigl, Viktória; Ujaczki, Éva; Vaszita, Emese; Molnár, Mónika

2017-10-01

Red mud can be applied as soil ameliorant to acidic, sandy and micronutrient deficient soils. There are still knowledge gaps regarding the effects of red mud on the soil microbial community. The Biolog EcoPlate technique is a promising tool for community level physiological profiling. This study presents a detailed evaluation of Biolog EcoPlate data from two case studies. In experiment "A" red mud from Ajka (Hungary) was mixed into acidic sandy soil in soil microcosms at 5-50 w/w%. In experiement "B" red mud soil mixture was mixed into low quality subsoil in a field experiment at 5-50 w/w%. According to average well color development, substrate average well color development and substrate richness 5-20% red mud increased the microbial activity of the acidic sandy soil over the short term, but the effect did not last for 10months. Shannon diversity index showed that red mud at up to 20% did not change microbial diversity over the short term, but the diversity decreased by the 10th month. 30-50% red mud had deteriorating effect on the soil microflora. 5-20% red mud soil mixture in the low quality subsoil had a long lasting enhancing effect on the microbial community based on all Biolog EcoPlate parameters. However, 50% red mud soil mixture caused a decrease in diversity and substrate richness. With the Biolog EcoPlate we were able to monitor the changes of the microbial community in red mud affected soils and to assess the amount of red mud and red mud soil mixture applicable for soil treatment in these cases. Copyright © 2017 Elsevier B.V. All rights reserved.

CHARGING SIDE OF #130 ELECTRIC FURNACE CO. REHEAT FURNACE IN ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

CHARGING SIDE OF #130 ELECTRIC FURNACE CO. REHEAT FURNACE IN REROLL BAY. CAKES FROM THE CASTING SHOP ARE BROUGHT UP TO ROLLING TEMPERATURE IN ONE OF TWO (#130 AND 146) GAS-FIRED FURNACES. A RADIO-CONTROLLED OVERHEAD CRANE TRANSFERS CAKES FROM FLATCARS TO THE ROLLER LINE LEADING INTO THE FURNACE. CAKES ARE HEATED AT 900-1000 DEGREES FAHRENHEIT FOR THREE TO FOUR HOURS. RATED FURNACE CAPACITY IS 100,000 LBS.\\HOUR. - American Brass Foundry, 70 Sayre Street, Buffalo, Erie County, NY

Hidden values in bauxite residue (red mud): recovery of metals.

PubMed

Liu, Yanju; Naidu, Ravi

2014-12-01

Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud. Copyright © 2014 Elsevier Ltd. All rights reserved.

Experimental Study on Application of Boron Mud Secondary Resource to Oxidized Pellets Production

NASA Astrophysics Data System (ADS)

Fu, Xiao-Jiao; Chu, Man-Sheng; Zhao, Jia-Qi; Chen, Shuang-Yin; Liu, Zheng-Gen; Wang, Si-Yuan

2017-07-01

In order to realize comprehensive and massive treatment of boron mud secondary resource, fundamental study on boron mud applied to oxidized pellets production as additive was carried out in the paper under laboratory conditions. The effects of boron mud on the performance of oxidized pellets were investigated systemically, and boron mud was combined with other boron-rich material innovatively. The results showed that, within certain limits, boron mud can improve properties of oxidized pellets. The bentonite content decreased to 0.3 % when adding 1.0 % boron mud additive and the pellets met blast furnace requirements. With the combination additive content 0.8 %, bentonite content can be further decreased to 0.2 %, and the pellets properties were better than base pellet. Therefore, it was an effective way to reduce environmental pollution and optimize blast furnace operation by developing boron mud secondary resource as pellets additive.

Acoustical Properties of Mud Sediments

DTIC Science & Technology

2015-09-30

Acoustical Properties of Mud Sediments Allan D. Pierce Boston University 399 Quaker Meeting House Road P. O. Box 339 East Sandwich, MA 03537...shallow-ocean mud sediments. Other goals are to assess prior data relating to the acoustic properties of mud and to provide guidance in the...development and interpretation of experiments. A related goal is to construct models that will guide inversion techniques for inferring properties of mud

Protracted outbreak of S. Enteritidis PT 21c in a large Hamburg nursing home

PubMed Central

Frank, Christina; Buchholz, Udo; Maaß, Monika; Schröder, Arthur; Bracht, Karl-Hans; Domke, Paul-Gerhard; Rabsch, Wolfgang; Fell, Gerhard

2007-01-01

Background During August 2006, a protracted outbreak of Salmonella (S.) Enteritidis infections in a large Hamburg nursing home was investigated. Methods A site visit of the home was conducted and food suppliers' premises tested for Salmonella. Among nursing home residents a cohort study was carried out focusing on foods consumed in the three days before the first part of the outbreak. Instead of relying on residents' memory, data from the home's patient food ordering system was used as exposure data. S. Enteritidis isolates from patients and suspected food vehicles were phage typed and compared. Results Within a population of 822 nursing home residents, 94 case patients among residents (1 fatality) and 17 among staff members were counted 6 through 29 August. The outbreak peaked 7 through 9 August, two days after a spell of very warm summer weather. S. Enteritidis was consistently recovered from patients' stools throughout the outbreak. Among the food items served during 5 through 7 August, the cohort study pointed to afternoon cake on all three days as potential risk factors for disease. Investigation of the bakery supplying the cake yielded S. Enteritidis from cakes sampled 31 August. Comparison of the isolates by phage typing demonstrated both isolates from patients and the cake to be the exceedingly rare phage type 21c. Conclusion Cake (various types served on various days) contaminated with S. Enteritidis were the likely vehicle of the outbreak in the nursing home. While the cakes were probably contaminated with low pathogen dose throughout the outbreak period, high ambient summer temperatures and failure to keep the cake refrigerated led to high pathogen dose in cake on some days and in some of the housing units. This would explain the initial peak of cases, but also the drawn out nature of the outbreak with cases until the end of August. Suggestions are made to nursing homes, aiding in outbreak prevention. Early outbreak detection is crucial, such that counter measures can be swift and drawn-out outbreaks of nosocomial food-borne infections avoided. PMID:17854497

Antifungal properties of fermentates and their potential to replace sorbate and propionate in pound cake.

PubMed

Samapundo, S; Devlieghere, F; Vroman, A; Eeckhout, M

2016-11-21

The major objective of this study was to assess the antifungal activities of commercially available 'clean label' fermentates and their potential to replace the preservative function of sorbate and propionate in cake. This study was performed in two parts. In the first part of the study the inhibitory activities of selected fermentates - FA, FB, FC and FD - towards Aspergillus tritici and Aspergillus amstelodami were assessed as a function of pH (5.0-6.5) on malt extract agar (MEA). In the second part of the study, challenge, shelf-life and sensorial tests were used to determine the suitability of these fermentates to replace potassium sorbate and calcium propionate in quarter pound cake. All the fermentates evaluated in this study all had significant (p<0.05) inhibitory activities towards A. tritici and A. amstelodami within the recommended dosage range for application in bakery products. In all cases, the inhibitory activity of the fermentates increased with a decrease in the pH and an increase in concentration. FC was generally the most inhibitory whilst FD was the least inhibitory. Significant (p<0.05) synergistic interactions were determined to occur between the effects of pH and concentration for all fermentates evaluated in this study. The sensorial tests with FC showed that cakes produced with ≤1% FC (on basis of the batter) did not differ significantly (p>0.05) in flavour from the reference cake (0.5% calcium propionate and 0.54% potassium sorbate). However, the challenge and shelf-life tests showed that cakes produced with ≤1% FC were not as microbiologically shelf-stable as the reference cake, especially when sliced. Therefore, it can be concluded that whilst fermentates have appreciable antifungal effects, their use could potentially result in reduced shelf-stabilities. Robust challenge and shelf-life tests would be recommended before the marketing of cakes were propionate and/or sorbate has been replaced to ensure accurate shelf-lives are stated. Copyright © 2016 Elsevier B.V. All rights reserved.

Illuminating Anaerobic Microbial Community and Cooccurrence Patterns across a Quality Gradient in Chinese Liquor Fermentation Pit Muds

PubMed Central

Hu, Xiaolong; Du, Hai; Ren, Cong

2016-01-01

Fermentation pit mud, an important reservoir of diverse anaerobic microorganisms, is essential for Chinese strong-aroma liquor production. Pit mud quality, according to its sensory characteristics, can be divided into three grades: degraded, normal, and high quality. However, the relationship between pit mud microbial community and pit mud quality is poorly understood, as are microbial associations within the pit mud ecosystem. Here, microbial communities at these grades were compared using Illumina MiSeq sequencing of the variable region V4 of the 16S rRNA gene. Our results revealed that the pit mud microbial community was correlated with its quality and environmental factors. Species richness, biodiversity, and relative and/or absolute abundances of Clostridia, Clostridium kluyveri, Bacteroidia, and Methanobacteria significantly increased, with corresponding increases in levels of pH, NH4+, and available phosphorus, from degraded to high-quality pit muds, while levels of Lactobacillus, dissolved organic carbon, and lactate significantly decreased, with normal samples in between. Furthermore, 271 pairs of significant and robust correlations (cooccurrence and negative) were identified from 76 genera using network analysis. Thirteen hubs of cooccurrence patterns, mainly under the Clostridia, Bacteroidia, Methanobacteria, and Methanomicrobia, may play important roles in pit mud ecosystem stability, which may be destroyed with rapidly increased levels of lactic acid bacteria (Lactobacillus, Pediococcus, and Streptococcus). This study may help clarify the relationships among microbial community, environmental conditions, and pit mud quality, allow the improvement of pit mud quality by using bioaugmentation and controlling environmental factors, and shed more light on the ecological rules guiding community assembly in pit mud. PMID:26896127

Warts phosphorylates Mud to promote Pins-mediated mitotic spindle orientation in Drosophila independent of Yorkie

PubMed Central

Dewey, Evan B.; Sanchez, Desiree; Johnston, Christopher A.

2015-01-01

SUMMARY Multicellular animals have evolved conserved signaling pathways that translate cell polarity cues into mitotic spindle positioning to control the orientation of cell division within complex tissue structures. These oriented cell divisions are essential for the development of cell diversity and the maintenance of tissue homeostasis. Despite intense efforts, the molecular mechanisms that control spindle orientation remain incompletely defined. Here we describe a role for the Hippo (Hpo) kinase complex in promoting Partner of Inscuteable (Pins)-mediated spindle orientation. Knockdown of Hpo, Salvador (Sav), or Warts (Wts) each result in a partial loss of spindle orientation, a phenotype previously described following loss of the Pins-binding protein Mushroom body defect (Mud). Similar to orthologs spanning yeast to mammals, Wts kinase localizes to mitotic spindle poles, a prominent site of Mud localization. Wts directly phosphorylates Mud in vitro within its C-terminal coiled-coil domain. This Mud coiled-coil domain directly binds the adjacent Pins-binding domain to dampen the Pins/Mud interaction, and Wts-mediated phosphorylation uncouples this intramolecular Mud interaction. Loss of Wts prevents cortical Pins/Mud association without affecting Mud accumulation at spindle poles, suggesting phosphorylation acts as a molecular switch to specifically activate cortical Mud function. Finally, loss of Wts in Drosophila imaginal disc epithelial cells results in diminished cortical Mud and defective planar spindle orientation. Our results provide new insights into the molecular basis for dynamic regulation of the cortical Pins/Mud spindle positioning complex and highlight a novel link with an essential, evolutionarily-conserved cell proliferation pathway. PMID:26592339

Warts phosphorylates mud to promote pins-mediated mitotic spindle orientation in Drosophila, independent of Yorkie.

PubMed

Dewey, Evan B; Sanchez, Desiree; Johnston, Christopher A

2015-11-02

Multicellular animals have evolved conserved signaling pathways that translate cell polarity cues into mitotic spindle positioning to control the orientation of cell division within complex tissue structures. These oriented cell divisions are essential for the development of cell diversity and the maintenance of tissue homeostasis. Despite intense efforts, the molecular mechanisms that control spindle orientation remain incompletely defined. Here, we describe a role for the Hippo (Hpo) kinase complex in promoting Partner of Inscuteable (Pins)-mediated spindle orientation. Knockdown of Hpo, Salvador (Sav), or Warts (Wts) each result in a partial loss of spindle orientation, a phenotype previously described following loss of the Pins-binding protein Mushroom body defect (Mud). Similar to orthologs spanning yeast to mammals, Wts kinase localizes to mitotic spindle poles, a prominent site of Mud localization. Wts directly phosphorylates Mud in vitro within its C-terminal coiled-coil domain. This Mud coiled-coil domain directly binds the adjacent Pins-binding domain to dampen the Pins/Mud interaction, and Wts-mediated phosphorylation uncouples this intramolecular Mud interaction. Loss of Wts prevents cortical Pins/Mud association without affecting Mud accumulation at spindle poles, suggesting phosphorylation acts as a molecular switch to specifically activate cortical Mud function. Finally, loss of Wts in Drosophila imaginal disc epithelial cells results in diminished cortical Mud and defective planar spindle orientation. Our results provide new insights into the molecular basis for dynamic regulation of the cortical Pins/Mud spindle positioning complex and highlight a novel link with an essential, evolutionarily conserved cell proliferation pathway. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Onset of Channelling in a Fluidized Mud Layer

NASA Astrophysics Data System (ADS)

Papanicolaou, T.; Tsakiris, A. G.; Billing, B. M.

2012-12-01

Fluidization of a soil occurs when the drag force exerted on the soil grains by upwelling water equals the submerged weight of the soil grains, hence reducing the effective (or contact) stress between the soil grains to zero. In nature, fluidization is commonly encountered in localized portions of highly saturated mud layers found in tidal flats, estuaries and lakes, where upward flow is initiated by significant pore water pressure gradients triggered by wave or tidal action. The water propagates through the fluidized mud layer by forming channels (or vents), carrying the fluidized mud to the surface and forming mud volcano structures. The presence of these fluidization channels alters the mud layer structure with implications on its hydraulic and geotechnical properties, such as the hydraulic conductivity. Despite the importance of these channels, the conditions that lead to their formation and their effects on the mud layer structure still remain poorly documented. The present study couples experimental and theoretical methods aimed at quantifying the conditions, under which fluidization of a saturated mud layer is accompanied by the formation of channels, and assessing the effects of channeling on the mud layer structure. Fluidization and channel formation in a mud layer were reproduced in the laboratory using a carefully designed fluidization column attached to a pressurized vessel (plenum). To eliminate any effects of the material, the mud was produced from pure kaolin clay and deionized water. Local porosity measurements along the mud layer prior, during and after fluidization were conducted using an Americium-241 gamma source placed on a fully automated carriage. Different water inflow rates, q, were applied to the base of the mud layer and the plenum pressure was monitored throughout the experiment. These experiments revealed that for high q values, a single vertical channel formed and erupted at the center of the fluidization column. Instead for low q values, the experiments suggested that a channel network formed within the mud layer leading to the eruption of multiple channels on the mud layer surface. The gamma source measurements captured quantitatively the porosity increase as the channel formed. The experiments were complemented with a theoretical analysis using the two-phase, flow mass and momentum governing equations. This analysis aims to establish a relation between the applied pressure, the fluid velocity and the local porosity of mud during the formation of the channels.

Comparison of Copper Scavenging Capacity between Two Different Red Mud Types

PubMed Central

Ma, Yingqun; Si, Chunhua; Lin, Chuxia

2012-01-01

A batch experiment was conducted to compare the Cu scavenging capacity between two different red mud types: the first one was a highly basic red mud derived from a combined sintering and Bayer process, and the second one was a seawater-neutralized red mud derived from the Bayer process. The first red mud contained substantial amounts of CaCO3, which, in combination with the high OH− activity, favored the immobilization of water-borne Cu through massive formation of atacamite. In comparison, the seawater-neutralized red mud had a lower pH and was dominated by boehmite, which was likely to play a significant role in Cu adsorption. Overall, it appears that Cu was more tightly retained by the CaCO3-dominated red mud than the boehmite-dominated red mud. It is concluded that the heterogeneity of red mud has marked influences on its capacity to immobilize water-borne Cu and maintain the long-term stability of the immobilized Cu species. The research findings obtained from this study have implications for the development of Cu immobilization technology by using appropriate waste materials generated from the aluminium industry.

The effects of drilling muds on marine invertebrate larvae and adults

DOE Office of Scientific and Technical Information (OSTI.GOV)

Raimondi, P.T.; Barnett, A.M.; Krause, P.R.

1997-06-01

A series of laboratory experiments tested the effects of drilling muds from an active platform off southern California on larvae and adults of marine invertebrates. Red abalone (Haliotis rufescens) were used to determine effects of drilling muds on fertilization, early development, survivorship, and settlement, and experiments on adult brown cup corals (Paracyathus stearnsii) tested effects on adult survivorship, viability, and tissue loss. Exposures to drilling muds did not have an effect on abalone fertilization or early development. However, several exposures to drilling muds resulted in weak, but significant, positive effects of drilling muds on settlement of competent larvae. In contrast,more » settlement of red abalone larvae on natural coralline algal crusts decreased with increasing concentrations of drilling muds. This suggests that drilling muds affect either the abalone`s ability to detect natural settlement inducers, or they affect the inducer itself. Exposure of brown cup corals to concentrations of drilling muds adversely impacted their survivorship and viability. These effects were likely caused by increased tissue mortality of the coral polyps.« less

Numerical investigation of fluid mud motion using a three-dimensional hydrodynamic and two-dimensional fluid mud coupling model

NASA Astrophysics Data System (ADS)

Yang, Xiaochen; Zhang, Qinghe; Hao, Linnan

2015-03-01

A water-fluid mud coupling model is developed based on the unstructured grid finite volume coastal ocean model (FVCOM) to investigate the fluid mud motion. The hydrodynamics and sediment transport of the overlying water column are solved using the original three-dimensional ocean model. A horizontal two-dimensional fluid mud model is integrated into the FVCOM model to simulate the underlying fluid mud flow. The fluid mud interacts with the water column through the sediment flux, current, and shear stress. The friction factor between the fluid mud and the bed, which is traditionally determined empirically, is derived with the assumption that the vertical distribution of shear stress below the yield surface of fluid mud is identical to that of uniform laminar flow of Newtonian fluid in the open channel. The model is validated by experimental data and reasonable agreement is found. Compared with numerical cases with fixed friction factors, the results simulated with the derived friction factor exhibit the best agreement with the experiment, which demonstrates the necessity of the derivation of the friction factor.

Let Them Eat Faux Cake

ERIC Educational Resources Information Center

Peace, Suze

2012-01-01

In this article, students create a "faux" cake sculpture. It is a three-dimensional artwork made of paper, colored with markers, and decorated with old marker caps and polystyrene packing peanuts for icing swirls.

Respiratory symptoms and sensitization in bread and cake bakers.

PubMed

Smith, T A; Smith, P W

1998-07-01

This purpose of this study was to examine the relationship between exposure to wheat flour, soya flour and fungal amylase and the development of work-related symptoms and sensitization in bread and cake bakery employees who have regular exposure to these substances. The study populations consisted of 394 bread bakery workers and 77 cake bakery workers whose normal jobs involved the sieving, weighing and mixing of ingredients. The groups were interviewed with the aim of identifying the prevalence, nature and pattern of any work-related respiratory symptoms. They were also skin-prick tested against the common bakery sensitizing agents, i.e., wheat flour, soya flour, rice flour and fungal amylase. The results of personal sampling for sieving, weighing and mixing operations at the bakeries from which the study groups were taken were collated in order to determine typical exposures to total inhalable dust from the ingredients, expressed as 8 hour time-weighted average exposures. Data from the health surveillance and collated dust measurements were compared with the aim of establishing an exposure-response relationship for sensitization. The prevalence of work-related symptoms in bread bakery and cake bakery ingredient handlers was 20.4% and 10.4% respectively. However, in a large proportion of those reporting symptoms in connection with work, the symptoms were intermittent and of short duration. It is considered that the aetiology of such symptoms is likely to be due to a non-specific irritant effect of high total dust levels, rather than allergy. None of the cake bakers and only 3.1% of the bread bakers had symptoms which were thought to be due to allergy to baking ingredients. Using skin-prick testing as a marker of sensitization, the prevalence of positive tests to wheat flour was 6% for the bread bakers and 3% for the cake bakers. Comparable prevalences for soya flour were 7% and 1% respectively. However, the prevalence of positive skin-prick tests to fungal amylase was 16% amongst the bread baking group with only a single employee (1%) in the cake baking group having a positive test. Furthermore, this employee had previously worked in a bread bakery. The difference in rates of sensitization to wheat flour between the bread and cake bakers is not statistically significant, whereas the difference for soya flour is at the borderline of statistical significance (p = 0.045). In contrast, the difference in fungal amylase sensitization is significant at the 0.1% level. For both bread and cake bakers, the 8 hour time-weighted average exposures for each of the activities showed a wide variation with mixing having the lowest average exposure and sieving the highest. Out of the allergens studied in this investigation, fungal amylase is the principal sensitizer in large scale bread bakeries, with the main source of exposure being the handling of bread improvers. In contrast, the risk of sensitization to wheat flour is low in both bread and cake bakeries. The absence of positive skin-prick tests in the subgroup of cake bakery employees who regularly handle fungal-amylase-containing flour suggests that their levels of exposure are below the threshold for sensitization to amylase.

21 CFR 172.838 - Polysorbate 65.

Code of Federal Regulations, 2012 CFR

2012-04-01

... solid-state, edible vegetable fat-water emulsions intended for use as substitutes for milk or cream in... finished edible vegetable fat-water emulsion. (5) As an emulsifier in cake icings and cake fillings, with...

21 CFR 172.838 - Polysorbate 65.

Code of Federal Regulations, 2013 CFR

2013-04-01

... solid-state, edible vegetable fat-water emulsions intended for use as substitutes for milk or cream in... finished edible vegetable fat-water emulsion. (5) As an emulsifier in cake icings and cake fillings, with...

The utilization of endopower β in commercial feed which contains palm kernel cake on performance of broiler chicken

NASA Astrophysics Data System (ADS)

Purba, S. S. A.; Tafsin, M.; Ginting, S. P.; Khairani, Y.

2018-02-01

Palm kernel cake is an agricultural waste that can be used as raw material in the preparation of poultry rations. The design used was Completely Randomized Design (CRD) with 5 treatments and 4 replications. Level endopower β used 0 % (R0), 0.02% (R1), 0.04% (R2) and 0.06% (R3). The results showed that R0a and R0b were significantly different from R3 in terms of diet consumption, body weight gain and the conversion ratio The utilization of endopower β in commercial diets containing palm kernel cake in broilers can increase body weight gain, feed consumption, improve feed use efficiency and even energy. It is concluded that utilization endpower β improve performances of broiler chicken fed by diet containing palm kernel cake.

Importance of molecular typing in confirmation of the source of a national hepatitis A virus outbreak in Norway and the detection of a related cluster in Germany.

PubMed

Guzman-Herrador, Bernardo R; Panning, Marcus; Stene-Johansen, Kathrine; Borgen, Katrine; Einöder-Moreno, Margot; Huzly, Daniela; Jensvoll, Laila; Lange, Heidi; Maassen, Sigrid; Myking, Solveig; Myrmel, Mette; Neumann-Haefelin, Christoph; Nygård, Karin; Wenzel, Jürgen J; Øye, Ann Kristin; Vold, Line

2015-11-01

In March 2014, after an increase of notifications of domestically acquired hepatitis A virus infections, an outbreak investigation was launched in Norway. Sequenced-based typing results showed that these cases were associated with a strain that was identical to one causing an ongoing multinational outbreak in Europe linked to frozen mixed berries. Thirty-three confirmed cases with the outbreak strain were notified in Norway from November 2013 to June 2014. Epidemiological evidence and trace-back investigations linked the outbreak to the consumption of a berry mix cake. Identification of the hepatitis A virus outbreak strain in berries from one of the implicated cakes confirmed the cake to be the source. Subsequently, a cluster in Germany linked to the cake was also identified.

Fuel Gas Demonstration Plant Program. Volume I. Demonstration plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1979-01-01

The objective of this project is for Babcock Contractors Inc. (BCI) to provide process designs, and gasifier retort design for a fuel gas demonstration plant for Erie Mining Company at Hoyt Lake, Minnesota. The fuel gas produced will be used to supplement natural gas and fuel oil for iron ore pellet induration. The fuel gas demonstration plant will consist of five stirred, two-stage fixed-bed gasifier retorts capable of handling caking and non-caking coals, and provisions for the installation of a sixth retort. The process and unit design has been based on operation with caking coals; however, the retorts have beenmore » designed for easy conversion to handle non-caking coals. The demonstration unit has been designed to provide for expansion to a commercial plant (described in Commercial Plant Package) in an economical manner.« less

Evaluation of dry heat treatment of soft wheat flour for the production of high ratio cakes.

PubMed

Keppler, S; Bakalis, S; Leadley, C E; Sahi, S S; Fryer, P J

2018-05-01

An accurate method to heat treat flour samples has been used to quantify the effects of heat treatment on flour functionality. A variety of analytical methods has been used such as oscillatory rheology, rheomixer, solvent retention capacity tests, and Rapid Visco Analysis (RVA) in water and in aqueous solutions of sucrose, lactic acid, and sodium carbonate. This work supports the hypothesis that heat treatment facilitates the swelling of starch granules at elevated temperature. Results furthermore indicated improved swelling ability and increased interactions of flour polymers (in particular arabinoxylans) of heat treated flour at ambient conditions. The significant denaturation of the proteins was indicated by a lack of gluten network formation after severe heat treatments as shown by rheomixer traces. Results of these analyses were used to develop a possible cake flour specification. A method was developed using response surfaces of heat treated flour samples in the RVA using i) water and ii) 50% sucrose solution. This can uniquely characterise the heat treatment a flour sample has received and to establish a cake flour specification. This approach might be useful for the characterisation of processed samples, rather than by baking cakes. Hence, it may no longer be needed to bake a cake after flour heat treatment to assess the suitability of the flour for high ratio cake production, but 2 types of RVA tests suffice. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Toxic compound, anti-nutritional factors and functional properties of protein isolated from detoxified Jatropha curcas seed cake.

PubMed

Saetae, Donlaporn; Suntornsuk, Worapot

2010-12-28

Jatropha curcas is a multipurpose tree, which has potential as an alternative source for biodiesel. All of its parts can also be used for human food, animal feed, fertilizer, fuel and traditional medicine. J. curcas seed cake is a low-value by-product obtained from biodiesel production. The seed cake, however, has a high amount of protein, with the presence of a main toxic compound: phorbol esters as well as anti-nutritional factors: trypsin inhibitors, phytic acid, lectin and saponin. The objective of this work was to detoxify J. curcas seed cake and study the toxin, anti-nutritional factors and also functional properties of the protein isolated from the detoxified seed cake. The yield of protein isolate was approximately 70.9%. The protein isolate was obtained without a detectable level of phorbol esters. The solubility of the protein isolate was maximal at pH 12.0 and minimal at pH 4.0. The water and oil binding capacities of the protein isolate were 1.76 g water/g protein and 1.07 mL oil/g protein, respectively. The foam capacity and stability, including emulsion activity and stability of protein isolate, had higher values in a range of basic pHs, while foam and emulsion stabilities decreased with increasing time. The results suggest that the detoxified J. curcas seed cake has potential to be exploited as a novel source of functional protein for food applications.

Toxic Compound, Anti-Nutritional Factors and Functional Properties of Protein Isolated from Detoxified Jatropha curcas Seed Cake

PubMed Central

Saetae, Donlaporn; Suntornsuk, Worapot

2011-01-01

Jatropha curcas is a multipurpose tree, which has potential as an alternative source for biodiesel. All of its parts can also be used for human food, animal feed, fertilizer, fuel and traditional medicine. J. curcas seed cake is a low-value by-product obtained from biodiesel production. The seed cake, however, has a high amount of protein, with the presence of a main toxic compound: phorbol esters as well as anti-nutritional factors: trypsin inhibitors, phytic acid, lectin and saponin. The objective of this work was to detoxify J. curcas seed cake and study the toxin, anti-nutritional factors and also functional properties of the protein isolated from the detoxified seed cake. The yield of protein isolate was approximately 70.9%. The protein isolate was obtained without a detectable level of phorbol esters. The solubility of the protein isolate was maximal at pH 12.0 and minimal at pH 4.0. The water and oil binding capacities of the protein isolate were 1.76 g water/g protein and 1.07 mL oil/g protein, respectively. The foam capacity and stability, including emulsion activity and stability of protein isolate, had higher values in a range of basic pHs, while foam and emulsion stabilities decreased with increasing time. The results suggest that the detoxified J. curcas seed cake has potential to be exploited as a novel source of functional protein for food applications. PMID:21339978

The diversity of mud volcanoes in the landscape of Azerbaijan

NASA Astrophysics Data System (ADS)

Rashidov, Tofig

2014-05-01

As the natural phenomenon the mud volcanism (mud volcanoes) of Azerbaijan are known from the ancient times. The historical records describing them are since V century. More detail study of this natural phenomenon had started in the second half of XIX century. The term "mud volcano" (or "mud hill") had been given by academician H.W. Abich (1863), more exactly defining this natural phenomenon. All the previous definitions did not give such clear and capacious explanation of it. In comparison with magmatic volcanoes, globally the mud ones are restricted in distribution; they mainly locate within the Alpine-Himalayan, Pacific and Central Asian mobile belts, in more than 30 countries (Columbia, Trinidad Island, Italy, Romania, Ukraine, Georgia, Azerbaijan, Turkmenistan, Iran, Pakistan, Indonesia, Burma, Malaysia, etc.). Besides it, the zones of mud volcanoes development are corresponded to zones of marine accretionary prisms' development. For example, the South-Caspian depression, Barbados Island, Cascadia (N.America), Costa-Rica, Panama, Japan trench. Onshore it is Indonesia, Japan, and Trinidad, Taiwan. The mud volcanism with non-accretionary conditions includes the areas of Black Sea, Alboran Sea, the Gulf of Mexico (Louisiana coast), Salton Sea. But new investigations reveal more new mud volcanoes and in places which were not considered earlier as the traditional places of mud volcanoes development (e.g. West Nile Rive delta). Azerbaijan is the classic region of mud volcanoes development. From over 800 world mud volcanoes there are about 400 onshore and within the South-Caspian basin, which includes the territory of East Azerbaijan (the regions of Shemakha-Gobustan and Low-Kura River, Absheron peninsula), adjacent water area of South Caspian (Baku and Absheron archipelagoes) and SW Turkmenistan and represents an area of great downwarping with thick (over 25 km) sedimentary series. Generally, in the modern relief the mud volcanoes represent more or less large uplifts on surface, often of plane-conical shape, rising for 5 to 400 m and more over the country (for example, mud volcano Toragay, 400 m height). The base diameter is from 100 m to 3-4 km and more. Like the magmatic ones, the mud volcanoes are crowned with crater of convex-plane or deeply-seated shape. In Azerbaijan there are all types of mud volcanoes: active, extinct, buried, submarine, island, abundantly oil seeping. According to their morphology they are defined into cone-shaped, dome-shaped, ridge-shaped, plateau-shaped. The crater shapes are also various: conical, convex-plane, shield-shaped, deeply-seated, caldera-like. The most complete morphological classification was given in "Atlas of mud volcanoes of Azerbaijan" (Yakubov et al., 1971). Recently (Aliyev Ad. et al., 2003) it was proposed a quite new morphological classification of mud volcanoes of Azerbaijan. For the first time the mud volcanic manifestations had been defined. Volcanoes are ranged according to morphological signs, crater shape and type of activity.

Potential treatments to reduce phorbol esters levels in jatropha seed cake for improving the value added product.

PubMed

Sadubthummarak, Umapron; Parkpian, Preeda; Ruchirawat, Mathuros; Kongchum, Manoch; Delaune, R D

2013-01-01

Jatropha seed cake contains high amounts of protein and other nutrients, however it has a drawback due to toxic compounds. The aim of this study was to investigate the methods applied to detoxify the main toxin, phorbol esters in jatropha seed cake, to a safe and acceptable level by maintaining the nutritional values. Phorbol esters are tetracyclic diterpenoids-polycyclic compounds that are known as tumor promoters and hence exhibited the toxicity within a broad range of species. Mismanagement of the jatropha waste from jatropha oil industries would lead to contamination of the environment, affecting living organisms and human health through the food chain, so several methods were tested for reducing the toxicity of the seed cake. The results from this investigation showed that heat treatments at either 120°C or 220°C for 1 hour and then mixing with adsorbing bentonite (10%), nanoparticles of zinc oxide (100 μg/g) plus NaHCO3 at 4%, followed by a 4-week incubation period yielded the best final product. The remaining phorbol esters concentration (0.05-0.04 mg/g) from this treatment was less than that reported for the nontoxic jatropha varieties (0.11-0.27 mg/g). Nutritional values of the seed cake after treatment remained at the same levels found in the control group and these values were crude protein (20.47-21.40 + 0.17-0.25%), crude lipid (14.27-14.68 + 0.13-0.14%) and crude fiber (27.33-29.67 + 0.58%). A cytotoxicity test conducted using L929 and normal human dermal fibroblast cell lines confirmed that most of the toxic compounds, especially phorbol esters, were shown as completely eliminated. The results suggested that the detoxification of phorbol esters residues in the jatropha seed cake was possible while it also retained nutritional values. Therefore, the methods to detoxify phorbol esters are necessary to minimize the toxicity of jatropha seed cake. Further, it is essential to reduce the possible environmental impacts that may be generated throughout the jatropha waste-handling process. However additional tests such as digestibility as well as acceptability of the treated jatropha seed cake should be conducted using both in vivo and in vitro studies before recommending the jatropha seed cake as a source of renewable animal feed and other value-added products.

Feasibility of Using Dredged Mud for Prepared the Permeable Brick

NASA Astrophysics Data System (ADS)

Zhou, Chaoqun; Cheng, Xiaosu; Zeng, Lingke; Wang, Hui; Chen, Jing

2017-10-01

Through experimental analysis found that the chemical composition of the dredged mud is similar to clay and the dredged mud does not leach heavy metals. Using the dredged mud in the preparation of permeable bricks reduced the quantity of incineration dredged mud buried in landfills, and the exploitation and consumption of natural sandstone. The dredged mud needs to be checked by the validation criteria when the second use, so we used the TCLP test to identify hazardous materials. Its leaching of heavy metals was in line with industry standard. And the basic formula of permeable brick were prepared, its performance was in line with national standards. The use of dredged mud preparing eco-friendly permeable bricks, not only solves the problem of environmental pollution, but also gets some economic and social profit.

Illuminating Anaerobic Microbial Community and Cooccurrence Patterns across a Quality Gradient in Chinese Liquor Fermentation Pit Muds.

PubMed

Hu, Xiaolong; Du, Hai; Ren, Cong; Xu, Yan

2016-04-01

Fermentation pit mud, an important reservoir of diverse anaerobic microorganisms, is essential for Chinese strong-aroma liquor production. Pit mud quality, according to its sensory characteristics, can be divided into three grades: degraded, normal, and high quality. However, the relationship between pit mud microbial community and pit mud quality is poorly understood, as are microbial associations within the pit mud ecosystem. Here, microbial communities at these grades were compared using Illumina MiSeq sequencing of the variable region V4 of the 16S rRNA gene. Our results revealed that the pit mud microbial community was correlated with its quality and environmental factors. Species richness, biodiversity, and relative and/or absolute abundances of Clostridia,Clostridium kluyveri, Bacteroidia, and Methanobacteria significantly increased, with corresponding increases in levels of pH, NH4 (+), and available phosphorus, from degraded to high-quality pit muds, while levels of Lactobacillus, dissolved organic carbon, and lactate significantly decreased, with normal samples in between. Furthermore, 271 pairs of significant and robust correlations (cooccurrence and negative) were identified from 76 genera using network analysis. Thirteen hubs of cooccurrence patterns, mainly under the Clostridia,Bacteroidia,Methanobacteria, and Methanomicrobia, may play important roles in pit mud ecosystem stability, which may be destroyed with rapidly increased levels of lactic acid bacteria (Lactobacillus,Pediococcus, and Streptococcus). This study may help clarify the relationships among microbial community, environmental conditions, and pit mud quality, allow the improvement of pit mud quality by using bioaugmentation and controlling environmental factors, and shed more light on the ecological rules guiding community assembly in pit mud. Copyright © 2016, American Society for Microbiology. All Rights Reserved.

Paraformaldehyde-Resistant Starch-Fermenting Bacteria in “Starch-Base” Drilling Mud

PubMed Central

Myers, G. E.

1962-01-01

Starch-fermenting bacteria were found in each of 12 samples of nonfermenting starch-base drilling mud examined. Of the 12 samples, 3 contained very active starch-fermenting gram-positive spore-bearing bacilli closely resembling Bacillus subtilis. Similar active starch-fermenting bacteria were found in fermenting starch-base drilling mud and in corn starch and slough water used to prepare such mud. The active starch-fermenting microorganisms completely hydrolyzed 1% (w/v) corn starch within 24 hr at 37.5 C. The active starch-fermenting bacteria isolated from fermenting drilling mud were capable of surviving 12 hr of continuous exposure to 0.1% (w/w) paraformaldehyde or 1 hr of continuous exposure to 0.5% (w/w) paraformaldehyde, with no diminution in starch-fermenting ability. The same organisms fermented starch after 3 hr of continuous exposure to 0.5% (w/w) paraformaldehyde, but not after 4 hr of exposure. The phenomenon of rapid disappearance of paraformaldehyde from fermenting drilling mud was observed in the laboratory using a modified sodium sulfite test. Paraformaldehyde, initially present in a concentration of 0.192 lb per barrel of mud, completely disappeared in 9 hr at 22 to 23 C. A significant decrease in paraformaldehyde concentration was detected 0.5 hr after preparation of the mud. It is suggested that the presence of relatively high concentrations of ammonia and chloride in the mud may facilitate the disappearance of paraformaldehyde. The failure of 0.1% (w/w) paraformaldehyde to inhibit the strong starch-fermenting microorganisms isolated from fermenting drilling mud, and the rapid disappearance of paraformaldehyde from the mud, explains the fermentation of starch which occurred in this mud, despite the addition of paraformaldehyde. PMID:13936949

Clostridium botulinum in Scottish fish farms and farmed trout.

PubMed

Burns, G F; Williams, H

1975-02-01

Rainbow trout and specimens of pond mud were collected from three fish farms and examined for the presence of Clostridium botulinum. Two of the farms were constructed with concrete channels and one was mud-bottomed. Cl. botulinum was isolated only from the mud-bottomed farm (24% of muds), and the isolates were all non-proteolytic type B. The implications of the presence of Cl. botulinum spores in the mud of fish farms is discussed.

Production of protease and lipase by solvent tolerant Pseudomonas aeruginosa PseA in solid-state fermentation using Jatropha curcas seed cake as substrate.

PubMed

Mahanta, Nilkamal; Gupta, Anshu; Khare, S K

2008-04-01

Deoiled Jatropha seed cake was assessed for its suitability as substrate for enzyme production by solid-state fermentation (SSF). Solvent tolerant Pseudomonas aeruginosa PseA strain previously reported by us was used for fermentation. The seed cake supported good bacterial growth and enzyme production (protease, 1818 U/g of substrate and lipase, 625 U/g of substrate) as evident by its chemical composition. Maximum protease and lipase production was observed at 50% substrate moisture, a growth period of 72 and 120 h, and a substrate pH of 6.0 and 7.0, respectively. Enrichment with maltose as carbon source increased protease and lipase production by 6.3- and 1.6-fold, respectively. Nitrogen supplementation with peptone for protease and NaNO(3) for lipase production also enhanced the enzyme yield reaching 11,376 U protease activity and 1084 U lipase activity per gram of Jatropha seed cake. These results demonstrated viable approach for utilization of this huge biomass by solid-state fermentation for the production of industrial enzymes. This offers significant benefit due to low cost and abundant availability of cake during biodiesel production.

Using modified soy protein to enhance foaming of egg white protein.

PubMed

Wang, Guang; Troendle, Molly; Reitmeier, Cheryll A; Wang, Tong

2012-08-15

It is well known that the foaming properties of egg white protein are significantly reduced when a small amount of yolk is mixed in the white. To improve foaming properties of yolk-contaminated egg white protein, soy protein isolate (SPI) and egg proteins were modified to make basic proteins, and effects of these modified proteins on egg white foaming were evaluated in a model and an angel cake system. SPI and egg yolk proteins were modified to have an isoelectric point of 10, and sonication was used to increase protein dispersibility after the ethyl esterification reaction. However, only the addition of sonicated and modified SPI (SMSPI) showed improvement of foaming in the 5% egg protein model system with 0.4% yolk addition. SMSPI was then used in making angel food cake to examine whether the cake performance reduction due to yolk contamination of the white would be restored by such alkaline protein. Cake performance was improved when cream of tartar was used together with SMSPI. Basic soy protein can be made and used to improve egg white foaming properties and cake performance. Copyright © 2012 Society of Chemical Industry.

Total control of chromium in tanneries - thermal decomposition of filtration cake from enzymatic hydrolysis of chrome shavings.

PubMed

Kocurek, P; Kolomazník, K; Bařinová, M; Hendrych, J

2017-04-01

This paper deals with the problem of chromium recovery from chrome-tanned waste and thus with reducing the environmental impact of the leather industry. Chrome-tanned waste was transformed by alkaline enzymatic hydrolysis promoted by magnesium oxide into practically chromium-free, commercially applicable collagen hydrolysate and filtration cake containing a high portion of chromium. The crude and magnesium-deprived chromium cakes were subjected to a process of thermal decomposition at 650°C under oxygen-free conditions to reduce the amount of this waste and to study the effect of magnesium removal on the resulting products. Oxygen-free conditions were applied in order to prevent the oxidation of trivalent chromium into the hazardous hexavalent form. Thermal decomposition products from both crude and magnesium-deprived chrome cakes were characterized by high chromium content over 50%, which occurred as eskolaite (Cr 2 O 3 ) and magnesiochromite (MgCr 2 O 4 ) crystal phases, respectively. Thermal decomposition decreased the amount of chrome cake dry feed by 90%. Based on the performed experiments, a scheme for the total control of chromium in the leather industry was designed.

Application of Zataria multiflora Boiss. and Cinnamon zeylanicum essential oils as two natural preservatives in cake.

PubMed

Kordsardouei, Habibe; Barzegar, Mohsen; Sahari, Mohamad Ali

2013-01-01

Oxidation of oils has an important effect on nutritional and organoleptic properties of foodstuffs. Nowadays, new tendency has created a necessity to use natural compounds such as essential oils for producing functional foods. In this study, antioxidant, antifungal, and organoleptic properties of Zataria multiflora Boiss. (ZMEO) and Cinnamon zeylanicum essential oils (CZEO) have been checked as two natural preservatives in the cakes. The antioxidant activity of essential oils were determined by measuring thiobarbituric, peroxide, and free fatty acid values of prepared cakes during 60 days storage at 25 ˚C. Antifungal properties of essential oils were determined and given as the ratio of colony number in samples containing ZMEO and CZEO to the control. Different concentrations of essential oils prevented oxidation rate and reducd preliminary and secondary oxidation products compared with butylate hydroxyanisole (BHA (100 and 200 ppm)) and control cakes. Moreover, ZMEO and CZEO at three concentrations (500, 1000, and 1500 ppm) reduced the fungal growth more than samples containing BHA (100 and 200 ppm) and the control. Our results showed that optimum concenteration of ZMEO and CZEO for using in the cakes was 500 ppm therefore it can be replaced instead of synthetic preservatives in foodstuffs.

Biogeochemical interactions among the arsenic, iron, humic substances, and microbes in mud volcanoes in southern Taiwan.

PubMed

Liu, Chia-Chuan; Maity, Jyoti Prakash; Jean, Jiin-Shuh; Sracek, Ondra; Kar, Sandeep; Li, Zhaohui; Bundschuh, Jochen; Chen, Chien-Yen; Lu, Hsueh-Yu

2011-01-01

Fluid and mud samples collected from Hsiaokunshui (HKS), Wushanting (WST), Yenshuikeng (YSK), Kunshuiping (KSP), Liyushan (LYS), and Sinyangnyuhu (SYNH) mud volcanoes of southwestern Taiwan were characterized for major ions, humic substances (HS) and trace elements concentrations. The relationship between the release of arsenic (As) and activities of sulfate-reducing bacteria has been assessed to understand relevant geochemical processes in the mud volcanoes. Arsenic (0.02-0.06 mg/L) and humic substances (4.13 × 10(-4) to 1.64 × 10(-3) mM) in the fluids of mud volcanoes showed a positive correlation (r = 0.99, p < 0.05) except in Liyushan mud volcano. Arsenic and iron in mud sediments formed two separate groups i) high As, but low Fe in HKS, WST, and SYNH; and ii) low As, but high Fe in the YSK, KSP, and LYS mud volcanoes. The Eh(S.H.E.) values of the mud volcano liquids were characterized by mild to strongly reducing conditions. The HKS, SYNH, and WST mud volcanoes (near the Chishan Fault) belongs to strong reducing environment (-33 to -116 mV), whereas the LYS, YSK, and KSP mud volcanoes located near the coastal plain are under mild reducing environment (-11 to 172 mV). At low Eh values mud volcanoes, saturation index (SI) values of poorly crystalline phases such as amorphous ferric hydroxide indicate understaturation, whereas saturation is reached in relatively high Eh(S.H.E.) values mud volcanoes. Arsenic contents in sediments are low, presumably due to its release to fluids (As/Fe ratio in YSK, KSP, and LYS sediment: 4.86 × 10(-4)-6.20 × 10(-4)). At low Eh(S.H.E.) values (mild to strong reducing environment), arsenic may co-precipitate with sulfides as a consequence of sulfate reduction (As/Fe ratios in WST, HKS, and SYNH sediments: 0.42-0.69).

Valorisation of waste ilmenite mud in the manufacture of sulphur polymer cement.

PubMed

Contreras, Manuel; Gázquez, Manuel Jesús; García-Díaz, Irene; Alguacil, Francisco J; López, Félix A; Bolívar, Juan Pedro

2013-10-15

This paper reports the preparation of sulphur polymer cements (SPCs) incorporating waste ilmenite mud for use in concrete construction works. The ilmenite mud raw material and the mud-containing SPCs (IMC-SPCs) were characterised physico-chemically and radiologically. The optimal IMC-SPC mixture had a sulphur/mud ratio (w/w) of 1.05 (mud dose 20 wt%); this cement showed the greatest compressive strength (64 MPa) and the lowest water absorption coefficient (0.4 g cm(-2) at 28 days). Since ilmenite mud is enriched in natural radionuclides, such as radium isotopes (2.0·10(3) Bq kg(-1)(228)Ra and 5.0·10(2) Bq kg(-1)(226)Ra), the IMC-SPCs were subjected to leaching experiments, which showed their environmental impact to be negligible. The activity concentration indices for the different radionuclides in the IMC-SPCs containing 10% and 20% ilmenite mud met the demands of international standards for materials used in the construction of non-residential buildings. Copyright © 2013 Elsevier Ltd. All rights reserved.

Suspended sediment concentration in the Lower Sea Scheldt (Belgium): long term trends and relation to mud disposal

NASA Astrophysics Data System (ADS)

Depreiter, Davy; van Holland, Gijsbert; Lanckriet, Thijs; Beirinckx, Kirsten; Vanlede, Joris; Maris, Tom

2015-04-01

In this presentation, results from different monitoring and research projects (OMES, MONEOS, Flexible Disposal and Marine-Fluvial mud ratio) will be integrated to increase the insight in the trends and relation between mud disposal and the increasing sediment concentrations (SSC) in the Lower Sea Scheldt. In the Scheldt Estuary, major projects have been carried out in the past decade, among which the third deepening of the navigation channel and the opening of the Deurganck dock. Maintenance dredging is carried out to guarantee a minimum navigation depth. A rising trend in the volume of mud dredged in the Lower Sea Scheldt is observed since 2006, the year after the opening of the Deurganck Dock. The trend is explained by increasing mud volumes dredged in this dock and on a nearby sill. This volume culminated in 2011 (4.8 million m³) when the depth of this dock was increased to its design depth. The dredged mud is disposed upstream, quickly to be resuspended. Near the mud disposal location, yearly averaged SSC (measured at 4.5 m above bed) tripled between 2005 and 2011 (108 to 348 mg/L), and SSC peaks increased even stronger. A multivariate regression model indicated a strong correlation between mud disposal volumes and timing and observed SSC. Mud disposal volumes and SSC where somewhat lower again after 2011. The SSC increase raises an alert with regard to the risk for a regime shift towards a hyperturbid system. Increasing SSC may indeed decrease the hydraulic resistance initiating a feedback mechanism that results in further increasing SSC values. It thus appears that more mud is being circulated: the Deurganck dock acts as mud sink, from which the mud is - after dredging and disposal - resuspended. The mud may have different sources: fluvial or marine influx. The increasing SSC might not only be related to the mud disposal, but also to changing tidal characteristics that enhance the influx of marine suspended sediments. To elucidate this, an analysis of the marine fraction in soil and suspended sediments has also been performed.

[Observation on eggs of Oncomelania hupensis hupensis with scanning electron microscope].

PubMed

Xia, Q B; Yuan, Y B; Liu, B; Tan, P P

2001-01-01

To observe the structure of the mud hull packed Oncomelania eggs and the surface structure of colloid membrane called the third grade membrane of eggs. Scanning electron microscopy was used to observe Oncomelania snail eggs with integral mud hull collected from eastern Dongting Lake. The mud hull of eggs was made of unshapen small humification combined with earth granules with a diameter of 2.6-9.2 microns. The mud hull in 60 um thickness was honeycomb-like in shape with many small holes and small folds on the wall. There were many round or irregularly round hollownesses on the inner layer of mud hull that contacts colloid membrane but no hole through mud hull. There were some protein fiber networks covering on the colloid membrane and apophysis. The structure of the mud hull showed that the exchange of matter was maintained between eggs and outside, and the mud hull is of great importance to regulating temperature and moisture for the growth of eggs by preventing hydrosoluble substances from penetrating into eggs. The protein fiber networks act on gluing mud hull and buffering outside power. The dense glue membrane might be a main barricade to prevent pharmaceutical molecules from penetrating into eggs.

Effect of graft source on unrelated donor hemopoietic stem cell transplantation in adults with acute myeloid leukemia after reduced-intensity or nonmyeloablative conditioning: a study from the Société Francaise de Greffe de Moelle et de Thérapie Cellulaire.

PubMed

Malard, Florent; Milpied, Noel; Blaise, Didier; Chevallier, Patrice; Michallet, Mauricette; Lioure, Bruno; Clément, Laurence; Hicheri, Yosr; Cordonnier, Catherine; Huynh, Anne; Yakoub-Agha, Ibrahim; Peffault de Latour, Regis; Mohty, Mohamad

2015-06-01

This retrospective report compared the 4-year outcomes of allogeneic stem cell transplantation (allo-SCT) in 651 adult patients with acute myeloid leukemia receiving a reduced-intensity (RIC) or nonmyeloablative conditioning (NMA) regimen according to the type of unrelated donors. These were either umbilical cord blood (UCB, n = 205), a 9/10 mismatched unrelated donor (MisMUD, n = 99), or a 10/10 matched unrelated donor (MUD, n = 347) graft. Neutrophil recovery was slower in UCB (74.5% by day 42) compared with MisMUD (94.8%) and MUD (95.6%) (P < .001). There was no significant difference in nonrelapse mortality between UCB and both MUD (hazard ratio [HR], 1.05; 95% confidence interval [CI], .62 to 1.78; P = .85) and MisMUD (HR, 1.58; 95% CI, .88 to 2.83; P = .13) The relapse/progression was similar between UCB and MisMUD (HR, .62; 95% CI, .37 to 1.03; P = .07), but was significantly lower in MUD compared with UCB (HR, .60; 95% CI, .39 to .92; P = .02). The rate of extensive chronic graft-versus-host disease (GVHD) was similar between UCB and both MUD (HR, 2.15; 95% CI, .93 to 4.97; P = .08) and MisMUD (HR, 1.84; 95% CI, .68 to 4.95; P = .23). The rate of severe grade III and IV acute GVHD was significantly increased in MisMUD compared with UCB (HR, 2.61; 95% CI, 1.30 to 5.23; P = .007). There was no significant difference in overall survival between UCB and both MisMUD (HR, .98; 95% CI, .66 to 1.45; P = .92) and MUD (HR, .74; 95% CI, .52 to 1.03; P = .08). These data suggest that in the setting of RIC/NMA, allo-SCT UCB is a valid alternative graft source, with significantly less chronic GVHD, compared with MisMUD, when there is no MUD available or when urgent transplantation is needed. Copyright © 2015 American Society for Blood and Marrow Transplantation. Published by Elsevier Inc. All rights reserved.

Graphene nanoplatelets as high-performance filtration control material in water-based drilling fluids

NASA Astrophysics Data System (ADS)

Ridha, Syahrir; Ibrahim, Arif; Shahari, Radzi; Fonna, Syarizal

2018-05-01

The main objective of this work is to evaluate the effectiveness of graphene nanoplatelets (GNP) as filtration control materials in water based drilling fluids. Three (3) general samples of water based drilling fluids were prepared including basic potassium chloride (KCl) drilling fluids, nanosilica (NS) drilling fluids and GNP drilling fluids. Several concentrations of NS and GNP were dispersed in controlled formulations of water based drilling fluids. Standard API filtration tests were carried out for comparison purposes as well as High Temperature High Pressure (HTHP) filtration tests at 150 °F (∼66 °C), 250 °F (∼121 °C) and 350 °F (∼177 °C) at a fixed 500 (∼3.45MPa) psi to study the filtration trend as a function of temperature. Mud cake samples from several tests were selectively chosen and analyzed under Field Emission Scanning Electron Microscope (FESEM) for its morphology. Results from this work show that nanoparticle concentrations play a factor in filtration ability of colloid materials in water based drilling fluids when studied at elevated temperature. Low temperature filtration, however, shows only small differences in volume in all the drilling fluid samples. 0.1 ppb concentrations of GNP reduced the fluid loss of 350 °F by 4.6 mL as compared to the similar concentration of NS drilling fluids.

An outbreak of mud-wrestling-induced pustular dermatitis in college students. Dermatitis palaestrae limosae.

PubMed

Adler, A I; Altman, J

1993-01-27

To investigate an outbreak of gram-negative folliculitis in relation to a common exposure, mud wrestling, and identify risk factors for dermatitis among those who mud wrestled. Case-control study. University of Washington, Seattle. Two college-residence groups of students. Cultures from affected students and from mud similar to that used for wrestling yielded Enterobacteriaceae. The odds ratio associated with mud wrestling was 79.5 (95% confidence interval, 13.9 to 895.4). Increased time spent wrestling was associated with increased risk. Skin trauma during wrestling or immersion in the mud increased the risk of infection (odds ratio, 23.1; 95% confidence interval, 1.7 to 1440.4). Mud wrestling is one cause of pustular follicular dermatitis. Trauma to the skin may be a necessary cofactor for the development of infection.

21 CFR 172.838 - Polysorbate 65.

Code of Federal Regulations, 2014 CFR

2014-04-01

... emulsions intended for use as substitutes for milk or cream in beverage coffee, with or without one or a... emulsion. (5) As an emulsifier in cake icings and cake fillings, with or without one or a combination of...

Coke from coal and petroleum

DOEpatents

Wynne, Jr., Francis E.; Lopez, Jaime; Zaborowsky, Edward J.

1981-01-01

A carbonaceous coke is manufactured by the delayed coking of a slurry mixture of from about 10 to about 30 weight percent of caking or non-caking coal and the remainder a petroleum resid blended at below 50.degree. C.

Changes of the antigenic and allergenic properties of a hen's egg albumin in a cake with gamma-irradiated egg white

NASA Astrophysics Data System (ADS)

Lee, Ju.-Woon; Seo, Ji.-Hyun; Kim, Jae.-Hun; Lee, Soo.-Young; Kim, Kwan.-Soo; Byun, Myung.-Woo

2005-04-01

Changes of the antigenicity and allergenicity of a hen's egg albumin (ovalbumin, OVA) in white layer cakes containing egg white gamma-irradiated with 10 or 20 kGy were monitored by an enzyme-linked immunosorbent assay (ELISA), individually formatted with mouse anti-OVA IgG (mouse IgG) and with egg allergic patients' IgE. Mouse IgG recognized OVA in the cakes with irradiated egg white better than that in the control with a non-irradiated one. Whereas, the detected concentrations of intact OVA in the control significantly decreased in the treatments, when determined by IgE-based ELISA. The results appeared to indicate that the antigenicity of the OVA increased, but that the allergenicity was decreased by irradiation and processing. Egg white irradiated for reducing the egg allergy could be used for producing a safer cake from the egg allergy.

Antifungal activity of Leuconostoc citreum and Weissella confusa in rice cakes.

PubMed

Baek, Eunjong; Kim, Hyojin; Choi, Hyejung; Yoon, Sun; Kim, Jeongho

2012-10-01

The antifungal activity of organic acids greatly improves the shelf life of bread and bakery products. However, little is known about the effect of lactic acid fermentation on fungal contamination in rice cakes. Here, we show that lactic acid fermentation in rice dough can greatly retard the growth of three fungal species when present in rice cakes, namely Cladosporium sp. YS1, Neurospora sp. YS3, and Penicillium crustosum YS2. The antifungal activity of the lactic acid bacteria against these fungi was much better than that of 0.3% calcium propionate. We found that organic acids including lactic and acetic acid, which are byproducts of lactic fermentation or can be artificially added, were the main antifungal substances. We also found that some Leuconostoc citreum and Weissella confusa strains could be good starter species for rice dough fermentation. These results imply that these lactic acid bacteria can be applicable to improve the preservation of rice cakes.

Experimental Study of Fouling Behavior of Main Substances (BSA, HA, SA) of Dissolved Organic Matter (DOM) in Dead-end Membrane Filtration

NASA Astrophysics Data System (ADS)

Sun, Yongjun; Zhu, Kexin; Khan, Bushra; Du, Xinpei; Hou, Lei; Zhao, Shuang; Li, Ping; Liu, Songbai; Song, Peng; Zhang, Hong; Jiang, Shuihong; Wang, Zhan; Zha, Shenghua

2018-01-01

In this study, the fouling behavior of PES ultrafiltration (UF) membrane with different DOM fractions including bovine serum albumin (BSA), sodium alginate (SA) and humic acid (HA) was systematically investigated. The result showed that the fouling mechanism of HA was cake formation while that of BSA and SA was caused by both pore blocking and cake formation due to the different particle size. Moreover, membrane fouling became more severe with the increase of feed concentration and TMP and it could be accurately described by the cake-complete model. The pore blocking resistance for SA was larger than that for BSA, whereas the cake resistance followed the sequence SA>BSA>HA. This observation offered insight into the differences in fouling behavior of the various DOM components and was further used as guidance for practical application.

Quinoa flour in baked products.

PubMed

Lorenz, K; Coulter, L

1991-07-01

The performance of quinoa-wheat flour blends (5/95, 10/90, 20/80, 30/70) were evaluated in breads, cakes and cookies. Breads baked with 5% and 10% quinoa flour were of good quality. Loaf volume decreased, crumb grain became more open and the texture slightly harsh at higher usage levels of quinoa flour. A bitter after taste was noted at the 30% level. Cake quality was acceptable with 5% and 10% of quinoa flour. Cake grain became more open and the texture less silky as the level of quinoa substitution increased. Cake taste improved with either 5% or 10% quinoa flour in the blend. Cookie spread and top grain scores decreased with increasing levels of quinoa flour blended with high-spread cookie flour. Flavor improved up to 20% quinoa flour in the blend. Cookie spread and cookie appearance was improved with a quinoa/low-spread flour blend by using 2% lecithin.

NMR signal analysis to characterize solid, aqueous, and lipid phases in baked cakes.

PubMed

Le Grand, F; Cambert, M; Mariette, F

2007-12-26

Proton mobility was studied in molecular fractions of some model systems and of cake using a 1H nuclear magnetic resonance (NMR) relaxation technique. For cake, five spin-spin relaxation times (T2) were obtained from transverse relaxation curves: T2 (1) approximately 20 micros, T2 (2) approximately 0.2 ms, T2 (3) approximately 3 ms, T2 (4) approximately 50 ms, and T2 (2) approximately 165 ms. The faster component was attributed to the solid phase, components 2 and 3 were associated with the aqueous phase, and the two slowest components were linked to the lipid phase. After cooking, the crust contained more fat but less water than the center part of the cake. The amount of gelatinized starch was lower in the crust, and water was more mobile due to less interaction with macromolecules. This preliminary study revealed different effects of storage on the center and crust.

40 CFR 230.42 - Mud flats.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 26 2012-07-01 2011-07-01 true Mud flats. 230.42 Section 230.42 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING SECTION 404(b)(1... Aquatic Sites § 230.42 Mud flats. (a) Mud flats are broad flat areas along the sea coast and in coastal...

40 CFR 230.42 - Mud flats.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 26 2013-07-01 2013-07-01 false Mud flats. 230.42 Section 230.42 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING SECTION 404(b)(1... Aquatic Sites § 230.42 Mud flats. (a) Mud flats are broad flat areas along the sea coast and in coastal...

40 CFR 230.42 - Mud flats.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Mud flats. 230.42 Section 230.42 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING SECTION 404(b)(1... Aquatic Sites § 230.42 Mud flats. (a) Mud flats are broad flat areas along the sea coast and in coastal...

40 CFR 230.42 - Mud flats.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 25 2014-07-01 2014-07-01 false Mud flats. 230.42 Section 230.42 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING SECTION 404(b)(1... Aquatic Sites § 230.42 Mud flats. (a) Mud flats are broad flat areas along the sea coast and in coastal...

40 CFR 230.42 - Mud flats.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 25 2011-07-01 2011-07-01 false Mud flats. 230.42 Section 230.42 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) OCEAN DUMPING SECTION 404(b)(1... Aquatic Sites § 230.42 Mud flats. (a) Mud flats are broad flat areas along the sea coast and in coastal...

30 CFR 250.1614 - Mud program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Mud program. 250.1614 Section 250.1614 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614 Mud program. (a) The quantities, characteristics, use, and testing of drilling mud and the related drilling procedures shall be designed and...

MUD for Learning: Classification and Instruction

ERIC Educational Resources Information Center

Hsieh, Chung-Hsiang; Sun, Chuen-Tsai

2006-01-01

From a constructivist point of view, the importance of MUDs (Multiple User Dungeons) in education is justified based on their community-forming, learning, and role-playing functions. The authors propose a typology for educational MUDs and discuss their individual instructional approaches in order to measure MUD potential in ten-os of…

Filter-based control of particulate matter from a lean gasoline direct injection engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parks, II, James E; Lewis Sr, Samuel Arthur; DeBusk, Melanie Moses

New regulations requiring increases in vehicle fuel economy are challenging automotive manufacturers to identify fuel-efficient engines for future vehicles. Lean gasoline direct injection (GDI) engines offer significant increases in fuel efficiency over the more common stoichiometric GDI engines already in the marketplace. However, particulate matter (PM) emissions from lean GDI engines, particularly during stratified combustion modes, are problematic for lean GDI technology to meet U.S. Environmental Protection Agency Tier 3 and other future emission regulations. As such, the control of lean GDI PM with wall-flow filters, referred to as gasoline particulate filter (GPF) technology, is of interest. Since lean GDImore » PM chemistry and morphology differ from diesel PM (where more filtration experience exists), the functionality of GPFs needs to be studied to determine the operating conditions suitable for efficient PM removal. In addition, lean GDI engine exhaust temperatures are generally higher than diesel engines which results in more continuous regeneration of the GPF and less presence of the soot cake layer common to diesel particulate filters. Since the soot layer improves filtration efficiency, this distinction is important to consider. Research on the emission control of PM from a lean GDI engine with a GPF was conducted on an engine dynamometer. PM, after dilution, was characterized with membrane filters, organic vs. elemental carbon characterization, and size distribution techniques at various steady state engine speed and load points. The engine was operated in three primary combustion modes: stoichiometric, lean homogeneous, and lean stratified. In addition, rich combustion was utilized to simulate PM from engine operation during active regeneration of lean NOx control technologies. High (>95%) PM filtration efficiencies were observed over a wide range of conditions; however, some PM was observed to slip through the GPF at high speed and load conditions. The PM characterization at various engine speeds and loads will help enable optimized GPF design and control to achieve more fuel efficient lean GDI vehicles with low PM emissions.« less

Effect of incorporation of walnut cake (Juglans regia) in concentrate mixture on degradation of dry matter, organic matter and production of microbial biomass in vitro in goat

PubMed Central

Mir, Mohsin Ahmad; Sharma, R. K.; Rastogi, Ankur; Barman, Keshab

2015-01-01

Aim: This study was carried out to investigate the effect of incorporation of different level of walnut cake in concentrate mixture on in vitro dry matter degradation in order to determine its level of supplementation in ruminant ration. Materials and Methods: Walnut cake was used @ 0, 10, 15, 20, 25 and 30% level to formulate an iso-nitrogenous concentrate mixtures and designated as T1, T2, T3, T4, T5 and T6 respectively. The different formulae of concentrate mixtures were used for in vitro gas production studies using goat rumen liquor with wheat straw in 40:60 ratio. Proximate composition, fiber fractionation and calcium and phosphrous content of walnut cake were estimated. Result: The per cent IVDMD value of T1 and T2 diets was 68.42 ± 1.20 and 67.25 ± 1.37 respectively which was found highest (P<0.05) T3, T4, T5 and T6. Similar trend was also found for TDOM and MBP. Inclusion of walnut cake at 10% level in the concentrate mixture does not affect in vitro dry matter digestibility (IVDMD), truly degradable organic matter (TDOM, mg/200 mg DM), total gas production, microbial biomass production (MBP) and efficiency of microbial biomass production (EMP). Conclusion: It is concluded that walnut cake incorporation up to 10% level in the iso -nitrogenous concentrate mixture has no any negative effect on in vitro digestibility of dry matter (DM), TDOM, MBP, EMP and total gas production in goat. PMID:27047013

Eo-Ulrichian to Neo-Ulrichian views: The renaissance of "layer-cake stratigraphy"

USGS Publications Warehouse

Brett, Carlton E.; McLaughlin, P.I.; Baird, G.C.

2007-01-01

Classical notions of "layer-cake stratigraphy" have been denigrated as representing an antiquated "Neptunian" view of the geologic record with the American paleontologist-stratigrapher E.O. Ulrich vilified as its quintessential advocate. Some of the extreme "layer-cake" interpretations of E.O. Ulrich are demonstrably incorrect, especially where applied in marginal marine and terrestrial settings. However, close scrutiny of Ulrich's work suggests that the bulk was correct and demonstrated considerable insight for the time. Subsequent development of facies concepts revolutionized geologists' view of time-space relationships in stratigraphy, but rather than focusing on facies patterns within the established stratigraphic (layer-cake) frameworks many geologists in North America came to view strata as parts of diachronous facies mosaics. Recent advances in the development of event and sequence stratigraphic paradigms are beginning to swing the pendulum back the other way. Possible causes of "layer-cake" patterns are numerous and varied, including: (1) parallelism of depositional strike and outcrop belts, especially in foreland basins, (2) very widespread environmental belts developed in low-relief cratonic areas, (3) time-averaging homogenizes facies to a limited extent, resulting in a very subtle signature of lateral change, (4) condensed beds (hardgrounds, bone beds, ironstones, etc.) often form in responses to extrabasinal forces, thus they cross-cut facies, and (5) large events (i.e. hurricanes, floods, tsunamis, eruptions, etc.) are "over represented" in the rock record. A revised ("Neo-Ulrichian") layer-cake paradigm carries many of the original correct empirical observations of pattern, noted by Ulrich, recast in terms of event and sequence stratigraphy.

Evaluation of fouling in nanofiltration for desalination using a resistance-in-series model and optical coherence tomography.

PubMed

Park, Jongkwan; Lee, Sungyun; You, Jeongyeop; Park, Sanghun; Ahn, Yujin; Jung, Woonggyu; Cho, Kyung Hwa

2018-06-12

Resistance-in-series models have been applied to investigate fouling behavior. However, it is difficult to model the influence of morphology on fouling behavior because resistance is indirectly calculated from the water flux and transmembrane pressure. In this study, optical coherence tomography (OCT) was applied to evaluate the resistance of the fouling layer based on fouling morphology. Sodium alginate, humic acid, and bovine serum albumin (BSA) with high salts concentrations (conductivity: 23 mS/cm) were used as model foulants. At the same total fouling resistance, BSA showed the highest cake layer thickness (BSA (114.5 μm) > humic acid (53.5 μm) > sodium alginate (20.0 μm)). However, a different order was found for the cake layer resistance (BSA > sodium alginate > humic acid). This indicates that fouling thickness is not correlated with cake layer resistance. According to the Carman-Kozeny equation, fouling layer porosity decreased in the following order: humic acid (0.30) > BSA (0.21) > sodium alginate (0.20). In addition, we provided a specific value that was calculated using the ratio between the fouling thickness and cake layer resistance. The results show that alginic acid induced a stronger cake layer resistance, despite its thin fouling layer, whereas BSA showed a relatively low potential for inducing cake layer resistance. The results obtained in this study could be used for estimating and predicting fouling behavior. Copyright © 2018 Elsevier B.V. All rights reserved.

Feeding differently processed soya bean. Part 1. Effect on performance, protein utilization, relative organ weights, carcass traits and economics of producing broiler-chickens.

PubMed

Aletor, V A; Olonimoyo, F I

1992-01-01

The comparative utilization of differently processed (roasted, cooked and oil cake) soya bean base diets and groundnut cake diet were evaluated in a feeding trial using 100 day-old Anak broiler-chicks. The response criteria included performance, protein utilization, relative organ weights, carcass traits and economy of production. At the end of the feeding trial, the average weight gains of chicks fed processed soya bean diets were significantly (P less than 0.05) higher than those fed groundnut cake and raw soya bean diets. Both feed consumption and efficiency were significantly (P less than 0.05) enhanced by processing. For example, feed consumption was highest in the chicks fed soya bean oil cake and least in those fed raw bean. Feed efficiency was best in chicks fed roasted soya bean. The relative weights [g/100 g body wt.] of the liver, kidneys, lungs, heart, gizzard and bursa were not significantly affected by the differently processed soya bean while the raw bean (unprocessed) significantly (P less than 0.01) increased pancreas weight. The dressed weight [%], eviscerated weight [%] and the relative weight of the thigh, drumsticks, chest, back and head were not significantly influenced by the dietary treatments. However, the relative weights of the shank and belly fat were significantly (P less than 0.05) affected. Cost-benefit analysis showed that the processed soya bean gave higher profit than groundnut cake diet. Among the soya bean diets, profit was in the order: roasted greater than cooked greater than oil cake greater than raw bean.

Nitrogen fractionation of certain conventional- and lesser-known by-products for ruminants.

PubMed

Mahesh, M S; Thakur, Sudarshan S; Kumar, Rohit; Malik, Tariq A; Gami, Rajkumar

2017-06-01

Dietary proteins for ruminants are fractionated according to solubility, degradability and digestibility. In the present experiment, 11 vegetable protein meals and cakes used in ruminant nutrition were included with a main focus on determining various nitrogen (N) fractions in vitro . Total N (N × 6.25) content varied from 22.98% (mahua cake) to 65.16% (maize gluten meal), respectively. Guar meal korma contained the lowest and rice gluten meal had the highest acid detergent insoluble nitrogen (ADIN; N × 6.25). Borate-phosphate insoluble N (BIN, N × 6.25) and Streptomyces griseus protease insoluble N (PIN; N × 6.25) were higher ( P  < 0.01) in maize gluten meal than in other feeds, whereas groundnut cake and sunflower cake had lower ( P  < 0.01) BIN, and PIN, respectively. Available N, calculated with the assumption that ADIN is indigestible, was maximum in guar meal korma and minimum in rice gluten meal. Furthermore, rapid and slowly degradable N (N × 6.25) was found to be higher ( P  < 0.01) in groundnut cake and coconut cake, respectively. Intestinal digestion of rumen undegradable protein, expressed as percent of PIN, was maximum in guar meal korma and minimum in rice gluten meal. It was concluded that vegetable protein meals differed considerably in N fractions, and therefore, a selective inclusion of particular ingredient is needed to achieve desired level of N fractions to aid precision N rationing for an improved production performance of ruminants.

Palm kernel cake obtained from biodiesel production in diets for goats: feeding behavior and physiological parameters.

PubMed

de Oliveira, R L; de Carvalho, G G P; Oliveira, R L; Tosto, M S L; Santos, E M; Ribeiro, R D X; Silva, T M; Correia, B R; de Rufino, L M A

2017-10-01

The objective of this study was to evaluate the effects of the inclusion of palm kernel (Elaeis guineensis) cake in diets for goats on feeding behaviors, rectal temperature, and cardiac and respiratory frequencies. Forty crossbred Boer male, non-castrated goats (ten animals per treatment), with an average age of 90 days and an initial body weight of 15.01 ± 1.76 kg, were used. The goats were fed Tifton 85 (Cynodon spp.) hay and palm kernel supplemented at the rates of 0, 7, 14, and 21% of dry matter (DM). The feeding behaviors (rumination, feeding, and idling times) were observed for three 24-h periods. DM and neutral detergent fiber (NDF) intake values were estimated as the difference between the total DM and NDF contents of the feed offered and the total DM and NDF contents of the orts. There was no effect of palm kernel cake inclusion in goat diets on DM intake (P > 0.05). However, palm kernel cake promoted a linear increase (P < 0.05) in NDF intake and time spent feeding and ruminating (min/day; %; period) and a linear decrease in time spent idling. Palm kernel cakes had no effects (P > 0.05) on the chewing, feeding, and rumination efficiency (DM and NDF) or on physiological variables. The use up to 21% palm kernel cake in the diet of crossbred Boer goats maintained the feeding behaviors and did not change the physiological parameters of goats; therefore, its use is recommended in the diet of these animals.

29 CFR 784.110 - Performing operations both on nonaquatic products and named aquatic products.

Code of Federal Regulations, 2010 CFR

2010-07-01

... of the exemptions is applicable to the making of any commodities from ingredients only part of which... codfish cakes, clam chowder, dog food, crab cakes, or livestock food containing aquatic products is often...

DASH diet to lower high blood pressure

MedlinePlus

... breakfast. For dessert, choose fresh fruit or low-fat frozen yogurt instead of high-calorie sweets, such as cakes or pies. Choose healthy snacks, such as unsalted rice cakes or popcorn, raw vegetables, or yogurt. Dried fruits, seeds, and nuts ...

Toxicity of used drilling fluids to mysids (Mysidopsis bahia)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaetz, C.T.; Montgomery, R.; Duke, T.W.

1986-01-01

Static, acute toxicity tests were conducted with mysids (Mysidopsis bahia) and 11 used drilling fluids (also called drilling muds) obtained from active drilling platforms in the Gulf of Mexico, U.S.A. Each whole mud was tested, along with three phases of each mud: a liquid phase with all particulate materials removed; a suspended particulate phase composed of soluble and lighter particulate fractions; and a solid phase composed mainly of drill cuttings and rapidly settling particulates. These muds represented seven of the eight generic mud types described by the U.S. Environmental Protection Agency for use on the U.S. Outer Continental Shelf. Themore » toxicity of the 11 muds tested was apparently enhanced by the presence of aromatics. Furthermore, one mud tested repeatedly showed loss of toxicity with time, possibly from volatilization of aromatic fractions. The data demonstrated that aromatics in the drilling fluids affected their toxicity to M. bahia.« less

A study of iron mineral transformation to reduce red mud tailings.

PubMed

Li, L Y

2001-01-01

This study examines the effects of iron mineral transformation in an aluminum extraction process on the settling behavior, and the physical and chemical properties of the resulting red mud slurry that must be disposed of. By producing a red mud with a higher solid content, the total volume of mud slurry will also be reduced for a given alumina production rate and more caustic soda will be recovered. The settling behavior and the mineralogical, physical, and physico-chemical properties of one bauxite and three red muds processed under varying conditions were analyzed based on examination of the iron mineral transformations. The properties of red muds derived from the same bauxite can differ markedly due to variations in operating conditions of the Bayer process, such as temperature and the addition of a reducing agent. The settling of red mud can be improved by converting goethite into hematite and/or magnetite to produce a mud of larger particle size, smaller specific surface area, and larger specific gravity, characteristics which reduce the total volume of mud slurry to be disposed of and which allow for less potential contamination from caustic soda. This study also found that the by-product--Bayer sodalite--has the high exchange capacity for Na+ that might contribute to the long-term environmental problems.

Safety evaluation of traces of nickel and chrome in cosmetics: The case of Dead Sea mud.

PubMed

Ma'or, Ze'evi; Halicz, Ludwik; Portugal-Cohen, Meital; Russo, Matteo Zanotti; Robino, Federica; Vanhaecke, Tamara; Rogiers, Vera

2015-12-01

Metal impurities such as nickel and chrome are present in natural ingredients-containing cosmetic products. These traces are unavoidable due to the ubiquitous nature of these elements. Dead Sea mud is a popular natural ingredient of cosmetic products in which nickel and chrome residues are likely to occur. To analyze the potential systemic and local toxicity of Dead Sea mud taking into consideration Dead Sea muds' natural content of nickel and chrome. The following endpoints were evaluated: (Regulation No. 1223/20, 21/12/2009) systemic and (SCCS's Notes of Guidance) local toxicity of topical application of Dead Sea mud; health reports during the last five years of commercial marketing of Dead Sea mud. Following exposure to Dead Sea mud, MoS (margin of safety) calculations for nickel and chrome indicate no toxicological concern for systemic toxicity. Skin sensitization is also not to be expected by exposure of normal healthy skin to Dead Sea mud. Topical application, however, is not recommended for already nickel-or chrome-sensitized persons. As risk assessment of impurities present in cosmetics may be a difficult exercise, the case of Dead Sea mud is taken here as an example of a natural material that may contain traces of unavoidable metals. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

Volume requirements for aerated mud drilling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guo, B.; Rajtar, J.M.

1995-09-01

Aerated mud drilling has been recognized as having many advantages over conventional mud drilling, such ass higher penetration rate, less formation damage, minimized lost circulation, and lower drilling cost. In some areas, the use of aerated mud as a circulating medium for drilling oil and gas wells is becoming an attractive practice. Maintaining an optimum combination of liquid and air flow rates is important in aerated drilling operations. However, most drilling operators are unclear on what constitutes the ``optimum combination of the liquid and air flow rates.`` Guo et al. presented a mathematical approach to determining the flowing bottomhole pressuremore » (BHP) for aerated mud drilling. This paper addresses the use of Guo et al.`s mathematical model to determine liquid and air volume requirements considering wellbore stability, pipe sticking, and formation damage as well as the cuttings-carry capacity of the aerated mud. For a formation-damage-prevention point of view, the liquid fraction in the fluid stream should e as low as possible. However, a sufficient mud flow rate is always required to make the hole stable and to maintain the cuttings-carrying capacity of the aerated mud without injecting much air volume. This paper provides a simple approach to determining the liquid and air volume requirements for aerated mud drilling.« less

Mud extrusion and ring-fault gas seepage - upward branching fluid discharge at a deep-sea mud volcano.

PubMed

Loher, M; Pape, T; Marcon, Y; Römer, M; Wintersteller, P; Praeg, D; Torres, M; Sahling, H; Bohrmann, G

2018-04-19

Submarine mud volcanoes release sediments and gas-rich fluids at the seafloor via deeply-rooted plumbing systems that remain poorly understood. Here the functioning of Venere mud volcano, on the Calabrian accretionary prism in ~1,600 m water depth is investigated, based on multi-parameter hydroacoustic and visual seafloor data obtained using ship-borne methods, ROVs, and AUVs. Two seepage domains are recognized: mud breccia extrusion from a summit, and hydrocarbon venting from peripheral sites, hosting chemosynthetic ecosystems and authigenic carbonates indicative of long-term seepage. Pore fluids in freshly extruded mud breccia (up to 13 °C warmer than background sediments) contained methane concentrations exceeding saturation by 2.7 times and chloride concentrations up to five times lower than ambient seawater. Gas analyses indicate an underlying thermogenic hydrocarbon source with potential admixture of microbial methane during migration along ring faults to the peripheral sites. The gas and pore water analyses point to fluids sourced deep (>3 km) below Venere mud volcano. An upward-branching plumbing system is proposed to account for co-existing mud breccia extrusion and gas seepage via multiple surface vents that influence the distribution of seafloor ecosystems. This model of mud volcanism implies that methane-rich fluids may be released during prolonged phases of moderate activity.

Experiment study of mud to the moving process influent about viscous debris flow along slope

NASA Astrophysics Data System (ADS)

Jun, JiXian; Ying, Liang; Li, Pan Hua; Qiang, OuGuo

2018-01-01

Mud is the main component of viscous debris flow. The physical model experiments of viscous debris flow were carried out through the mixing mud with different density and fixed components of coarse particles. The width, longitudinal movement distance and motion velocity were recorded by video cameras during experiment. Through viscous debris flow physical model experiments, the influence of mud to transverse width, longitudinal movement distance and motion velocity was discussed. The physical model experiment results show that the motion forms change from inviscid particle flow to viscous debris flow and to the whole mass sliding with the increase of mud density; the width and the length along the slope decrease with mud density increasing; the movement process has classified phenomena about viscous debris flow composed by different mud densities: the velocity increases rapidly with time and the change gradient is steady when the density of mud is lower than 1.413g/cm3; the movement process can be divided into two stages when the density of mud is higher than 1.413g/cm3: the movement velocity is lower and the gradient change is small in the initial stage; but in the second stage, the movement velocity increases quickly, and the gradient is higher than the first stage, and with steady value.

Acoustic scattering from mud volcanoes and carbonate mounds.

PubMed

Holland, Charles W; Weber, Thomas C; Etiope, Giuseppe

2006-12-01

Submarine mud volcanoes occur in many parts of the world's oceans and form an aperture for gas and fluidized mud emission from within the earth's crust. Their characteristics are of considerable interest to the geology, geophysics, geochemistry, and underwater acoustics communities. For the latter, mud volcanoes are of interest in part because they pose a potential source of clutter for active sonar. Close-range (single-interaction) scattering measurements from a mud volcano in the Straits of Sicily show scattering 10-15 dB above the background. Three hypotheses were examined concerning the scattering mechanism: (1) gas entrained in sediment at/near mud volcano, (2) gas bubbles and/or particulates (emitted) in the water column, (3) the carbonate bio-construction covering the mud volcano edifice. The experimental evidence, including visual, acoustic, and nonacoustic sensors, rules out the second hypothesis (at least during the observation time) and suggests that, for this particular mud volcano the dominant mechanism is associated with carbonate chimneys on the mud volcano. In terms of scattering levels, target strengths of 4-14 dB were observed from 800 to 3600 Hz for a monostatic geometry with grazing angles of 3-5 degrees. Similar target strengths were measured for vertically bistatic paths with incident and scattered grazing angles of 3-5 degrees and 33-50 degrees, respectively.

Utilization of red mud and Pb/Zn smelter waste for the synthesis of a red mud-based cementitious material.

PubMed

Li, Yuan-Cheng; Min, Xiao-Bo; Ke, Yong; Chai, Li-Yuan; Shi, Mei-Qing; Tang, Chong-Jian; Wang, Qing-Wei; Liang, Yan-Jie; Lei, Jie; Liu, De-Gang

2018-02-15

A new method in which Pb/Zn smelter waste containing arsenic and heavy metals (arsenic sludge), red mud and lime are utilized to prepare red mud-based cementitious material (RCM) is proposed in this study. XRD, SEM, FTIR and unconfined compressive strength (UCS) tests were employed to assess the physicochemical properties of RCM. In addition, ettringite and iron oxide-containing ettringite were used to study the hydration mechanism of RCM. The results show that the UCS of the RCM (red mud+arsenic sludge+lime) was higher than that of the binder (red mud+arsenic sludge). When the mass ratio of m (binder): m (lime) was 94:6 and then maintained 28days at ambient temperature, the UCS reached 12.05MPa. The red mud has potential cementitious characteristics, and the major source of those characteristics was the aluminium oxide. In the red mud-arsenic sludge-lime system, aluminium oxide was effectively activated by lime and gypsum to form complex hydration products. Some of the aluminium in ettringite was replaced by iron to form calcium sulfoferrite hydrate. The BCR and leaching toxicity results show that the leaching concentration was strongly dependent on the chemical speciation of arsenic and the hydration products. Therefore, the investigated red mud and arsenic sludge can be successfully utilized in cement composites to create a red mud-based cementitious material. Copyright © 2017 Elsevier B.V. All rights reserved.

Multi-Sensor Mud Detection

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.; Matthies, Larry H.

2010-01-01

Robust mud detection is a critical perception requirement for Unmanned Ground Vehicle (UGV) autonomous offroad navigation. A military UGV stuck in a mud body during a mission may have to be sacrificed or rescued, both of which are unattractive options. There are several characteristics of mud that may be detectable with appropriate UGV-mounted sensors. For example, mud only occurs on the ground surface, is cooler than surrounding dry soil during the daytime under nominal weather conditions, is generally darker than surrounding dry soil in visible imagery, and is highly polarized. However, none of these cues are definitive on their own. Dry soil also occurs on the ground surface, shadows, snow, ice, and water can also be cooler than surrounding dry soil, shadows are also darker than surrounding dry soil in visible imagery, and cars, water, and some vegetation are also highly polarized. Shadows, snow, ice, water, cars, and vegetation can all be disambiguated from mud by using a suite of sensors that span multiple bands in the electromagnetic spectrum. Because there are military operations when it is imperative for UGV's to operate without emitting strong, detectable electromagnetic signals, passive sensors are desirable. JPL has developed a daytime mud detection capability using multiple passive imaging sensors. Cues for mud from multiple passive imaging sensors are fused into a single mud detection image using a rule base, and the resultant mud detection is localized in a terrain map using range data generated from a stereo pair of color cameras.

Carbonate mud bodies in middle Mississippian strata of southern Indiana and northern Kentucky: End members of a middle Mississippian mud mound spectrum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, M.A.; Dodd, J.R.

1990-06-01

Relatively small, lens-shaped carbonate mud bodies are common features in the Ramp Creek Formation and Harrodsburg Limestone (Mississippian) of southern Indiana and northern Kentucky. The outcrop dimensions of the lenses range from approximately 10 cm thick and 3 m wide to as much as 2 m thick and in excess of 100 m wide; their three-dimensional geometry is unknown. The lens cores consist of dolomitic mudstone that grades laterally and vertically into increasingly more fossiliferous wackestone to grainstone with fenestrate bryozoans and echinoderms being the dominant fossils. The great abundance of fenestrate bryozoan fragments surrounding the lenses suggests that lensmore » evolution was controlled by the trapping of carbonate mud by the baffling action of bryozoans. Wisps of organic material preserved in the lens cores may be remnants of some form of non-calcareous algae that also baffled and trapped carbonate mud. These mud lenses are end members of a spectrum of Mississippian carbonate mud bodies ranging in size from these small lenses to the classical Waulsortian mounds that may be hundreds of meters thick and a kilometer or more broad. All of these carbonate mud bodies may have in part formed by baffling and localizing of carbonate mud by organisms and in part by local production of carbonate mud. The major difference between large and small bodies is the water depth in which each formed. The Ramp Creek-Harrodsburg mud lenses may be miniature Waulsortian mounds that developed at or above fair-weather wave base on a relatively shallow carbonate platform rather than on shelf-to-basin slopes as proposed for the classical Waulsortian mounds.« less

Episodic Deep Fluid Expulsion at Mud Volcanoes in the Kumano Forearc Basin, SE Offshore Japan

NASA Astrophysics Data System (ADS)

Hammerschmidt, S.; Kopf, A.

2014-12-01

Compressional forces at convergent margins govern a variety of processes, most prominently earthquakes, landslides and mud volcanoes in the forearc. Although all seem related to fluid pressure changes, mud volcanoes are not only characterized by expulsion of fluids, but also fluidized mud and clasts that got ripped-up during mud ascension. They hence provide information regarding mobilization depth, diagenetic overprint, and geodynamic pathways. At the Nankai Trough subduction zone, SE offshore Japan, mud volcanism id common and supposed to be related to seismogenic processes. During MARUM Expedition SO-222 with R/V SONNE, mud volcanoes in the Kumano forearc basin were mapped, cored and sampled. By extending the Integrated Ocean Drilling Program (IODP) Kumano transect landwards, 5 new mud volcanoes were identified by multibeam mapping. Cores revealed mud breccia with semi-consolidated silt- to claystone clasts and gaseous fluid escape structures, while the hemipelagic background sediments are characterized by intercalations of turbidites, ash layers and calcareous fossils. Clasts were subject to thin-section analyses, and the cores were sampled for XRD analyses and radiocarbon dating. Clasts showed prominent deformation structures, neomorphism and pores and fractures filled with polycrystalline quartz and/or calcite cement, probably formed during deep burial and early metamorphosis. Illite crystallinity based on XRD measurements varies between 0.24 and 0.38, which implies that the material originates from the Anchizone at depths ≥ 4 km. Radiocarbon dating revealed ages between 4450 and 30300 yr cal. BP, with age reversals occurring not earlier than 17000 yr cal. BP. Radiocarbon dating beneath turbidites and ash layers found at mud volcano #9 points to an episodic occurrence of these earthquake-related features in intervals of ca. 620 yr, while the mud volcano itself remained inactive. In summary, the preliminary results suggest that the mud volcanoes are nurtured from a reservoir within the older part of the accretionary prism, but that mud volcanic activity is less frequent than major earthquakes. Future models will focus on source depth and temperature, and might elucidate the prerequisites for fluid migration and its role in seismogenesis at the Nankai Trough subduction zone.

Gypsum addition to soils contaminated by red mud: implications for aluminium, arsenic, molybdenum and vanadium solubility.

PubMed

Lehoux, Alizée P; Lockwood, Cindy L; Mayes, William M; Stewart, Douglas I; Mortimer, Robert J G; Gruiz, Katalin; Burke, Ian T

2013-10-01

Red mud is highly alkaline (pH 13), saline and can contain elevated concentrations of several potentially toxic elements (e.g. Al, As, Mo and V). Release of up to 1 million m(3) of bauxite residue (red mud) suspension from the Ajka repository, western Hungary, caused large-scale contamination of downstream rivers and floodplains. There is now concern about the potential leaching of toxic metal(loid)s from the red mud as some have enhanced solubility at high pH. This study investigated the impact of red mud addition to three different Hungarian soils with respect to trace element solubility and soil geochemistry. The effectiveness of gypsum amendment for the rehabilitation of red mud-contaminated soils was also examined. Red mud addition to soils caused a pH increase, proportional to red mud addition, of up to 4 pH units (e.g. pH 7 → 11). Increasing red mud addition also led to significant increases in salinity, dissolved organic carbon and aqueous trace element concentrations. However, the response was highly soil specific and one of the soils tested buffered pH to around pH 8.5 even with the highest red mud loading tested (33 % w/w); experiments using this soil also had much lower aqueous Al, As and V concentrations. Gypsum addition to soil/red mud mixtures, even at relatively low concentrations (1 % w/w), was sufficient to buffer experimental pH to 7.5-8.5. This effect was attributed to the reaction of Ca(2+) supplied by the gypsum with OH(-) and carbonate from the red mud to precipitate calcite. The lowered pH enhanced trace element sorption and largely inhibited the release of Al, As and V. Mo concentrations, however, were largely unaffected by gypsum induced pH buffering due to the greater solubility of Mo (as molybdate) at circumneutral pH. Gypsum addition also leads to significantly higher porewater salinities, and column experiments demonstrated that this increase in total dissolved solids persisted even after 25 pore volume replacements. Gypsum addition could therefore provide a cheaper alternative to recovery (dig and dump) for the treatment of red mud-affected soils. The observed inhibition of trace metal release within red mud-affected soils was relatively insensitive to either the percentage of red mud or gypsum present, making the treatment easy to apply. However, there is risk that over-application of gypsum could lead to detrimental long-term increases in soil salinity.

Diplomacy Through Earth Sciences: An Overview of US Geological Survey Technical Assistance Regarding the Ongoing LUSI Mud Eruption, East Java, Indonesia

NASA Astrophysics Data System (ADS)

Casadevall, T. J.

2009-12-01

In June 2007, the US Department of State (DOS) requested assistance from the USGS to provide technical guidance and advice to the US Mission in Indonesia regarding the Lumpur Sidoarjo (LUSI) mud crisis. In May 2006, LUSI began as a mud eruption from a series of mud springs adjacent to an oil and gas exploration well being drilled near Surabaya, East Java, Indonesia. The production of mud and waters from the LUSI crater area has now continued for more than 3 years with no significant change in mud production rate (~110,000 cubic meters per day) nor in temperature of the mud (70-80 degrees C). Engineers suggest that mud production will continue at these rates for years to decades to come. Regardless of future activity at LUSI, the current mud accumulation of more than 100 million cubic meters poses a physical and environmental hazard which requires continuous monitoring and observation. The first response to the 2007 DOS request involved a site visit to Indonesia in September 2007. The result of that visit was to recommend to the Government of Indonesia (GOI) that they focus on long-term management of the mud rather than focus on the controversy as to the cause of the eruption or the debate about stopping the flow. Other recommendations from the initial 2007 technical visit included contracting for a US scientist to be co-located with engineers of the Sidoarjo Mud Management Board (BPLS) in Surabaya, East Java, to advise and consult on day-to-day developments at the site of the mud eruption. A second technical team visit by USGS scientists and an engineer from the US Army Corps of Engineers in October-November 2008 made additional recommendations on the long-term management of the mud and was followed in December by the start of a 6 month contract for the US mud adviser. From the start of activity in mid-2006 through late-2008, there was a clear sense of urgency at the US Mission in Indonesia to provide guidance and advice and included the personal intervention of the new US Ambassador. The USGS has completed the requests made in the June 2007 DOS cable, including an initial characterization of the mud and fluids; an analysis of land surface changes using the INSAR method; and an assessment of the seismic hazards in East Java. In the coming year, USGS will assist DOI agencies in the geophysical monitoring of the LUSI area and in the continued characterization of mud and fluids produced by the eruption.

GT-5 Recovery Slice Cake

NASA Image and Video Library

1965-08-29

S65-51660 (29 Aug. 1965) --- Astronauts Charles Conrad Jr. (left) and L. Gordon Cooper Jr. prepare to slice into the huge cake prepared for them by the cooks onboard the aircraft carrier USS Lake Champlain. They are using ornamental Navy swords for knives.

Old ingredients for a new recipe? Neem cake, a low-cost botanical by-product in the fight against mosquito-borne diseases.

PubMed

Benelli, Giovanni; Murugan, Kadarkarai; Panneerselvam, Chellasamy; Madhiyazhagan, Pari; Conti, Barbara; Nicoletti, Marcello

2015-02-01

Mosquitoes (Diptera: Culicidae) represent an important threat to millions of people worldwide, since they act as vectors for important pathogens, such as malaria, yellow fever, dengue and West Nile. Control programmes mainly rely on chemical treatments against larvae, indoor residual spraying and insecticide-treated bed nets. In recent years, huge efforts have been carried out to propose new eco-friendly alternatives, with a special focus on the evaluation of plant-borne mosquitocidal compounds. Major examples are neem-based products (Azadirachta indica A. Juss, Meliaceae) that have been proven as really effective against a huge range of pests of medical and veterinary importance, including mosquitoes. Recent research highlighted that neem cake, a cheap by-product from neem oil extraction, is an important source of mosquitocidal metabolites. In this review, we examined (i) the latest achievements about neem cake metabolomics with special reference to nor-terpenoid and related content; (ii) the neem cake ovicidal, larvicidal and pupicidal toxicity against Aedes, Anopheles and Culex mosquito vectors; (iii) its non-target effects against vertebrates; and (iv) its oviposition deterrence effects on mosquito females. Overall, neem cake can be proposed as an eco-friendly and low-cost source of chemicals to build newer and safer control tools against mosquito vectors.

Application of Zataria multiflora Boiss. and Cinnamon zeylanicum essential oils as two natural preservatives in cake

PubMed Central

Kordsardouei, Habibe; Barzegar, Mohsen; Sahari, Mohamad Ali

2013-01-01

Objective: Oxidation of oils has an important effect on nutritional and organoleptic properties of foodstuffs. Nowadays, new tendency has created a necessity to use natural compounds such as essential oils for producing functional foods. In this study, antioxidant, antifungal, and organoleptic properties of Zataria multiflora Boiss. (ZMEO) and Cinnamon zeylanicum essential oils (CZEO) have been checked as two natural preservatives in the cakes. Materials and Methods: The antioxidant activity of essential oils were determined by measuring thiobarbituric, peroxide, and free fatty acid values of prepared cakes during 60 days storage at 25 ˚C. Antifungal properties of essential oils were determined and given as the ratio of colony number in samples containing ZMEO and CZEO to the control. Results: Different concentrations of essential oils prevented oxidation rate and reducd preliminary and secondary oxidation products compared with butylate hydroxyanisole (BHA (100 and 200 ppm)) and control cakes. Moreover, ZMEO and CZEO at three concentrations (500, 1000, and 1500 ppm) reduced the fungal growth more than samples containing BHA (100 and 200 ppm) and the control. Conclusion: Our results showed that optimum concenteration of ZMEO and CZEO for using in the cakes was 500 ppm therefore it can be replaced instead of synthetic preservatives in foodstuffs. PMID:25050280

Effects of spacer orientations on the cake formation during membrane fouling: Quantitative analysis based on 3D OCT imaging.

PubMed

Liu, Xin; Li, Weiyi; Chong, Tzyy Haur; Fane, Anthony G

2017-03-01

Spacer design plays an important role in improving the performance of membrane processes for water/wastewater treatment. This work focused on a fundamental issue of spacer design, i.e., investigating the effects of spacer orientations on the fouling behavior during a membrane process. A series of fouling experiments with different spacer orientation were carried out to in situ characterize the formation of a cake layer in a spacer unit cell via 3D optical coherence tomography (OCT) imaging. The cake layers formed at different times were digitalized for quantitatively analyzing the variation in the cake morphology as a function of time. In particular, the local deposition rates were evaluated to determine the active regions where the instantaneous changes in deposit thickness were significant. The characterization results indicate that varying the spacer orientation could substantially change the evolution of membrane fouling by particulate foulants and thereby result in a cake layer with various morphologies; the competition between growth and erosion at different locations would instantaneously respond to the micro-hydrodynamic environment that might change with time. This work confirms that the OCT-based characterization method is a powerful tool for exploring novel spacer design. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mud transportation on a steep shelf, Rio de La Plata shelf, Puerto Rico

USGS Publications Warehouse

Grove, K.A.; Pilkey, O.H.; Trumbull, J.V.A.

1982-01-01

Hurricanes David (August 29-30, 1979) and Frederick (September 2-5, 1979) caused major flooding of the Rio de La Plata in northern Puerto Rico. A thin mud layer was deposited across the narrow insular shelf adjacent to the river mouth. Within 5 months, fair-weather shelf-winnowing processes moved the mud layer entirely from the shelf, 0.5 to 2 km to the shelf break at the 50-m contour and beyond. The process of mud movement is termed 'mud hopping.' ?? 1982 A. M. Dowden, Inc.

Isolation of indigenous enteroviruses from chemically treated and dewatered sludge samples.

PubMed Central

Goddard, M R; Bates, J; Butler, M

1982-01-01

Samples of wastewater sludge were examined for infectious enteroviruses before and after they had been chemically conditioned and dewatered. The least virus was recovered from the cake produced by filter pressing of sludge, which had a greatly increased solids content (39 to 45% [wt/vol]) relative to the untreated sludge (4.2 to 6.2% [wt/vol]) and in one plant was at pH 11 due to the lime conditioner used. Conditioning with a cationic polyelectrolyte before dewatering by centrifugation produced a watery sludge (2.7 to 5.3% [wt/vol]) from which high titers of infectious virus were recovered which were often greater than those isolated from the untreated sludge (0.6 to 1.4% [wt/vol]). This was thought to be due to saturation of virus and sludge floc adsorption sites by the polyelectrolyte, resulting in the liberation of virions from the sludge solids. PMID:6295275

Experimental Study of the Influence of the Concentration of Organic Water-Coal Fuel Components on the Integral Ignition Characteristics

NASA Astrophysics Data System (ADS)

Vershinina, K. Yu.; Kuznetsov, G. V.; Strizhak, P. A.

2017-01-01

To enlarge the power raw material base, the processes of stable initiation of combustion of drops of organic watercoal fuels have been investigated. For the main components, we used filter cakes (coal processing waste), anthracite, bituminous and brown coals of brands D and B2, water, and spent machine, turbine, and transformer oils. We have established the influence of concentrations of components on the minimum (limiting) ignition temperatures of organic water-coal fuels and the ignition delay times of drops of fuel components with initial sizes of 0.25-1.5 mm. Investigations were carried out for oxidizer temperatures of 600-1100 K and its velocities of 0.5-5 m/s characteristic of units, aggregates, and large and small power plants. We have determined the characteristic differences of organic water-coal fuel from water-coal fuel and the close laws of the investigated processes for these fuels.

Investigation of Single Phase NanoCellulose Transport through Porous Media

NASA Astrophysics Data System (ADS)

Dziuba, Carter Jordan

The application of nanotechnology to the petroleum industry has seen many recent advancements. Nanocellulose is an emerging nanoparticle at the forefront of research. Before nanocellulose can be injected into petroleum reservoirs, further understanding is needed as to the retention mechanisms that occur during nanocellulose transport through porous media. A series of unconsolidated sandpack floods were preformed with nanocellulose and the resulting retention and permeability reduction were measured. The experimental variables include nanocellulose type, sand grain size, flowrate, and salinity. It was found that all types of nanocellulose tested showed significantly different transport properties. Retention and permeability reduction increased as grain size decreased or flowrate decreased. As a general trend, the larger the size of aggregates in bulk solution, the greater the retention and permeability reduction. Salinity was found to be the primary parameter affecting transport. Increased salinity caused additional aggregation which resulted in increased straining and filter cake formation.

Literature review on production process to obtain extra virgin olive oil enriched in bioactive compounds. Potential use of byproducts as alternative sources of polyphenols.

PubMed

Frankel, Edwin; Bakhouche, Abdelhakim; Lozano-Sánchez, Jesús; Segura-Carretero, Antonio; Fernández-Gutiérrez, Alberto

2013-06-05

This review describes the olive oil production process to obtain extra virgin olive oil (EVOO) enriched in polyphenol and byproducts generated as sources of antioxidants. EVOO is obtained exclusively by mechanical and physical processes including collecting, washing, and crushing of olives, malaxation of olive paste, centrifugation, storage, and filtration. The effect of each step is discussed to minimize losses of polyphenols from large quantities of wastes. Phenolic compounds including phenolic acids, alcohols, secoiridoids, lignans, and flavonoids are characterized in olive oil mill wastewater, olive pomace, storage byproducts, and filter cake. Different industrial pilot plant processes are developed to recover phenolic compounds from olive oil byproducts with antioxidant and bioactive properties. The technological information compiled in this review will help olive oil producers to improve EVOO quality and establish new processes to obtain valuable extracts enriched in polyphenols from byproducts with food ingredient applications.

Performance and techno-economic assessment of several solid-liquid separation technologies for processing dilute-acid pretreated corn stover.

PubMed

Sievers, David A; Tao, Ling; Schell, Daniel J

2014-09-01

Solid-liquid separation of pretreated lignocellulosic biomass slurries is a critical unit operation employed in several different processes for production of fuels and chemicals. An effective separation process achieves good recovery of solute (sugars) and efficient dewatering of the biomass slurry. Dilute acid pretreated corn stover slurries were subjected to pressure and vacuum filtration and basket centrifugation to evaluate the technical and economic merits of these technologies. Experimental performance results were used to perform detailed process simulations and economic analysis using a 2000 tonne/day biorefinery model to determine differences between the various filtration methods and their process settings. The filtration processes were able to successfully separate pretreated slurries into liquor and solid fractions with estimated sugar recoveries of at least 95% using a cake washing process. A continuous vacuum belt filter produced the most favorable process economics. Copyright © 2014 Elsevier Ltd. All rights reserved.

Pore-scale Numerical Simulation Using Lattice Boltzmann Method for Mud Erosion in Methane Hydrate Bearing Layers

NASA Astrophysics Data System (ADS)

Yoshida, T.; Sato, T.; Oyama, H.

2014-12-01

Methane hydrates in subsea environments near Japan are believed to new natural gas resources. These methane hydrate crystals are very small and existed in the intergranular pores of sandy sediments in sand mud alternate layers. For gas production, several processes for recovering natural gas from the methane hydrate in a sedimentary reservoir have been proposed, but almost all technique are obtain dissociated gas from methane hydrates. When methane hydrates are dissociated, gas and water are existed. These gas and water are flown in pore space of sand mud alternate layers, and there is a possibility that the mud layer is eroded by these flows. It is considered that the mad erosion causes production trouble such as making skins or well instability. In this study, we carried out pore scale numerical simulation to represent mud erosion. This research aims to develop a fundamental simulation method based on LBM (Lattice Boltzmann Method). In the simulation, sand particles are generated numerically in simulation area which is approximately 200x200x200μm3. The periodic boundary condition is used except for mud layers. The water/gas flow in pore space is calculated by LBM, and shear stress distribution is obtained at the position flow interacting mud surface. From this shear stress, we consider that the driving force of mud erosion. As results, mud erosion can be reproduced numerically by adjusting the parameters such as critical shear stress. We confirmed that the simulation using LBM is appropriate for mud erosion.

Radiological characterization of clay mixed red mud in particular as regards its leaching features.

PubMed

Hegedűs, Miklós; Sas, Zoltán; Tóth-Bodrogi, Edit; Szántó, Tamás; Somlai, János; Kovács, Tibor

2016-10-01

The reuse of industrial by-products such as red mud is of great importance. In the case of the building material industry the reuse of red mud requires a cautious attitude, since the enhanced radionuclide content of red mud can have an effect on human health. The natural radionuclide content of red mud from the Ajka red mud reservoir and the clay sample from a Hungarian brick factory were determined by gamma spectrometry. It was found that maximum 27.8% red mud content can be added to fulfil the conditions of the EU-BSS. The effect of heat treatment was investigated on a red mud-clay mixture and it was found that in the case of radon and thoron exhalation the applied heat reduced remarkably the exhalation capacities. The leaching features of red mud and different mixtures were studied according to the MSZ-21470-50 Hungarian standard, the British CEN/TS 14429 standard and the Tessier sequential extraction method. The Tessier method and the MSZ-21470-50 standard are suitable for the characterization of materials; however, they do not provide enough information for waste deposition purposes. To this end, we propose using the CEN/TS 14429 method, because it is easy to use, and gives detailed information about the material's behaviour under different pH conditions, however, further measurements are necessary. Copyright © 2016 Elsevier Ltd. All rights reserved.

Calcium ketoglutarate versus calcium acetate for treatment of hyperphosphataemia in patients on maintenance haemodialysis: a cross-over study.

PubMed

Birck, R; Zimmermann, E; Wassmer, S; Nowack, R; van der Woude, F J

1999-06-01

Since dietary restrictions and phosphorus removal by haemodialysis (HD) are not sufficient to control serum phosphate (s-phosphate) levels in dialysis patients the use of oral phosphate binders is mandatory. Calcium ketoglutarate (CaKE) is an analogue of glutamic acid exerting phosphate binding properties. Therefore we compared this substance to calcium acetate (CaAC) in a 24-weeks open cross-over trial in 28 maintenance HD patients. Medications and HD prescriptions were kept unchanged during the trial. Following 2 weeks of withdrawal of phosphate binders, patients were randomly assigned to one of the calcium salts for 12 weeks; after a second withdrawal of 2 weeks, all patients were shifted to the other treatment for another 12 weeks. All patients received equimolar doses of CaKE and CaAC with respect to the amount of prescribed elemental calcium. Treatment with CaAC and CaKE significantly reduced s-phosphate levels after 4 weeks (CaAC 1.95+/-0.6 vs. 2.4+/-0.53 mmol/l, P = 0.004; CaKE 1.95+/-0.4 vs. 2.47+/-0.63 mmol/l, P = 0.0001) reaching a virtually stable plateau over the remaining observation time without significant differences between the groups. The incidence of hypercalcaemia defined as a serum calcium level > or =2.8 mmol/l was significantly higher in CaAC than in CaKE treated patients (n = 8 vs. n = 1, P = 0.03). There were no significant differences in serum intact parathyroid hormone (PTH) bicarbonate, albumin or calcitriol levels between the groups after 12 weeks treatment. We conclude that CaKE is as effective as CaAC for treatment of hyperphosphataemia in chronic HD patients and may be particularly helpful in patients who are prone to develop hypercalcaemia.

Different Oils and Health Benefit Statements Affect Physicochemical Properties, Consumer Liking, Emotion, and Purchase Intent: A Case of Sponge Cake.

PubMed

Poonnakasem, Naratip; Pujols, Kairy Dharali; Chaiwanichsiri, Saiwarun; Laohasongkram, Kalaya; Prinyawiwatkul, Witoon

2016-01-01

Effects of different oils on physicochemical properties, consumer liking, emotion, and purchase intent of sponge cakes were evaluated. Three healthy oils (extra virgin coconut oil, EVCO; extra virgin olive oil, EVOO; rice bran oil, RBO) compared with butter (the control), were used at 20% (w/w, wheat flour basis) in sponge cake formulations. Five positive (calm, good, happy, pleased, satisfied) and 3 negative (guilty, unsafe, worried) emotion terms, selected from the EsSense Profile(®) with slight modification using an online (N = 234) check-all-that-apply questionnaire, were used for consumer testing. Consumers (N = 148) evaluated acceptability of 9 sensory attributes on a 9-point hedonic scale, 8 emotion responses on a 5-point rating scale, and purchase intent on a binomial scale. Overall liking, emotion, and purchase intent were evaluated before compared with after health benefit statement of oils had been given to consumers. Overall liking and positive emotion (except calm) scores of sponge cake made with EVCO were higher than those made with EVOO and RBO. Specific volume, expansion ratio, and moisture content of control, EVCO, and EVOO were not significantly different, but higher than RBO sponge cake. JAR results showed that sponge cake made with RBO had the least softness that was reflected by the highest hardness (6.61 to 9.69 compared with. 12.76N). Oil (EVCO/EVOO/RBO) health benefit statement provided to consumer significantly increased overall liking, positive emotion, and purchase intent scores while decreased negative emotion scores. Overall liking and pleased emotion were critical attributes influencing purchase intent (odds ratio = 2.06 to 3.75), whereas calm and happy became not critical after health benefit statement had been given. © 2015 Institute of Food Technologists®

Foams prepared from whey protein isolate and egg white protein: 2. Changes associated with angel food cake functionality.

PubMed

Berry, Tristan K; Yang, Xin; Foegeding, E Allen

2009-06-01

The effects of sucrose on the physical properties and thermal stability of foams prepared from 10% (w/v) protein solutions of whey protein isolate (WPI), egg white protein (EWP), and their combinations (WPI/EWP) were investigated in wet foams and angel food cakes. Incorporation of 12.8 (w/v) sucrose increased EWP foam stability (drainage 1/2 life) but had little effect on the stability of WPI and WPI/EWP foams. Increased stability was not due to viscosity alone. Sucrose increased interfacial elasticity (E ') of EWP and decreased E' of WPI and WPI/EWP combinations, suggesting that altered interfacial properties increased stability in EWP foams. Although 25% WPI/75% EWP cakes had similar volumes as EWP cakes, cakes containing WPI had larger air cells. Changes during heating showed that EWP foams had network formation starting at 45 degrees C, which was not observed in WPI and WPI/EWP foams. Moreover, in batters, which are foams with additional sugar and flour, a stable foam network was observed from 25 to 85 degrees C for batters made from EWP foams. Batters containing WPI or WPI/EWP mixtures showed signs of destabilization starting at 25 degrees C. These results show that sucrose greatly improved the stability of wet EWP foams and that EWP foams form network structures that remain stable during heating. In contrast, sucrose had minimal effects on stability of WPI and WPI/EWP wet foams, and batters containing these foams showed destabilization prior to heating. Therefore, destabilization processes occurring in the wet foams and during baking account for differences in angel food cake quality.

Effect of Inoculation Techniques and Relative Humidity on the Growth of Molds on the Surfaces of Yellow Layer Cakes

PubMed Central

Fustier, Patrick; Lafond, Alain; Champagne, Claude P.; Lamarche, François

1998-01-01

Four inoculation techniques were compared for initiation of growth on cake surfaces: spot, air cabinet, spray (atomizer), and talc addition methods. Molds were isolated from commercial cakes and were identified as Aspergillus sydowii, Aspergillus ochraceus, Penicillium funiculosum, and Eurotium herbariorum. Cake surfaces were inoculated with mold spores and incubated under three equilibrium relative humidity (ERH) levels: 97, 85, and 75%. Random contamination by spores in a ventilated air cabinet was the simplest method of inoculation, but standard deviations in the inoculation rates (20% on a relative scale) were almost twice those observed with the other methods. The spot method was the most reproducible. Cake samples inoculated in the air cabinet had colony counts 10 times lower than those obtained for potato dextrose agar plates at 97% ERH, which was not the case with the spray and talc methods. Growth of molds was much slower in the samples incubated in 75% relative humidity, with all methods. Colony counts were generally similar in systems adjusted at 85 to 97% ERH but were lower for samples incubated at 75% ERH. In comparisons of the shelf life estimates obtained by the various inoculation methods, a correlation coefficient (r2) of 0.70 was obtained between the spot method and the other methods of inoculation, while talc, air cabinet, and spray shelf life data were correlated better (r2 ≈ 0.97). The spot method appeared to be the method of choice in consideration of ease of use, precision, and the ability to enable the study of the effects of the environment on mold-free shelf life as well as on the rate of growth of molds on cakes. PMID:16349479

Boron-rich mud volcanoes of the Black Sea region: Modern analogues to ancient sea-floor tourmalinites associated with Sullivan-type Pb-Zn deposits?

NASA Astrophysics Data System (ADS)

Slack, John F.; Turner, Robert J. W.; Ware, Paul L. G.

1998-05-01

Large submarine mud volcanoes in the abyssal part of the Black Sea south of the Crimean Peninsula are similar in many respects to synsedimentary mud volcanoes in the Mesoproterozoic Belt-Purcell basin. One of the Belt-Purcell mud volcanoes directly underlies the giant Sullivan Pb-Zn-Ag deposit in southeastern British Columbia. Footwall rocks to the Sullivan deposit comprise variably tourmalinized siltstone, conglomerate, and related fragmental rock; local thin pyrrhotite-rich and spessartine-quartz beds are interpreted as Fe and Fe-Mn exhalites, respectively. Analogous Fe- and Mn-rich sediments occur near the abyssal Black Sea mud volcanoes. Massive pyrite crusts and associated carbonate chimneys discovered in relatively shallow waters (˜200 m depth) west of the Crimean Peninsula indicate an active sea-floor hydrothermal system. Subaerial mud volcanoes on the Kerch and Taman Peninsulas (˜100 km north of the abyssal mud volcanoes) contain saline thermal waters that locally have very high B contents (to 915 mg/L). These data suggest that tourmalinites might be forming in or near submarine Black Sea mud volcanoes, where potential may also exist for Sullivan-type Pb-Zn mineralization.

Observed salinity changes in the Alappuzha mud bank, southwest coast of India and its implication to hypothesis of mudbank formation

NASA Astrophysics Data System (ADS)

Muraleedharan, K. R.; Dinesh Kumar, P. K.; Prasanna Kumar, S.; Srijith, B.; John, Sebin; Naveen Kumar, K. R.

2017-04-01

Alappuzha mud bank draws special attention among the twenty-mud bank locations reported along the Kerala coast by its remoteness from riverine sources. Among several hypotheses proposed for the formation of mud bank, the subterranean hypothesis was most accepted because of the occurrence of low salinity in the bottom layers. The present study provides evidence to show that occurrence of low salinity waters near the bottom in the mud bank region is an artifact of measuring technique employed for the measurement of salinity. The usual technique of conductivity based salinity determination completely fails in the presence of water laden with high amount of suspended sediment. Laboratory experiments were conducted to determine the response of electrode and conductivity cell sensor types to determine the salinity using a range of suspended sediment in the water column. Actual sediment samples from the mud bank region were utilized for the above studies. Based on field observations and experiments, we conclude that the low salinity was the manifestation of the presence highly turbid fluid mud formation in the mud bank region rather than the influence of fresh water.

Mud Banks along the southwest coast of India are not too muddy for plankton.

PubMed

Jyothibabu, R; Balachandran, K K; Jagadeesan, L; Karnan, C; Arunpandi, N; Naqvi, S W A; Pandiyarajan, R S

2018-02-07

Considering Alappuzha Mud Bank in the southern Kerala coast as a typical case of biologically productive Mud Banks that form along the southwest coast of India during the Southwest Monsoon (June - September), the present study addresses several pertinent missing links between the physical environment in Mud Banks and their influence on plankton stock. This study showed that very strong coastal upwelling prevails in the entire study domain during the Southwest Monsoon, which manifests itself in the form of significantly cool, hypoxic and nitrate-rich waters surfacing near the coast. The upwelled water persisting throughout the Southwest Monsoon period was found to have fuelled the exceptionally high phytoplankton stock in the entire study area, including the Mud Bank region. Having accepted that Mud Banks are special because of the calm sea surface conditions and relatively high turbidity level in the water column around them, the present study showed that except at points close to the sea bottom, turbidity level in the Alappuzha Mud Bank was below the critical level to inhibit the plankton stock. The suspended sediments that form in the Mud Bank occasionally could be attributed to the disturbance of the bottom fluid muddy layer and their vertical spurts.

Removal of hexavalent chromium by using red mud activated with cetyltrimethylammonium bromide.

PubMed

Li, Deliang; Ding, Ying; Li, Lingling; Chang, Zhixian; Rao, Zhengyong; Lu, Ling

2015-01-01

The removal of hexavalent chromium [Cr(VI)] from aqueous solution by using red mud activated with cetyltrimethylammonium bromide (CTAB) was studied. The optimum operation parameters, such as CTAB concentration, pH values, contact time, and initial Cr(VI) concentration, were investigated. The best concentration of CTAB for modifying red mud was found to be 0.50% (mCTAB/VHCl,0.6 mol/L). The lower pH (<2) was found to be much more favourable for the removal of Cr(VI). Red mud activated with CTAB can greatly improve the removal ratio of Cr(VI) as high as four times than that of original red mud. Adsorption equilibrium was reached within 30 min under the initial Cr(VI) concentration of 100 mg L(-1). The isotherm data were analysed using Langmuir and Freundlich models. The adsorption of Cr(VI) on activated red mud fitted well to the Langmuir isotherm model, and the maximum adsorption capacity was estimated as 22.20 mg g(-1) (Cr/red mud). The adsorption process could be well described using the pseudo-second-order model. The result shows that activated red mud is a promising agent for low-cost water treatment.

Method and apparatus for optimizing determination of the originating depth of borehole cuttings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mc Auley, J.A.; Eppler, S.G.

1987-11-24

This patent describes a method for determining the arrival at the surface of an identifiable material from a predetermined drilling depth independent of pump stroke rate and intermittent operations during the utilization of at least a drill bit, a positive displacement mud pump and drilling mud during the drilling of a well. The method comprises the steps of: adding identifiable material to the drilling mud as the drilling mud is being pumped downwardly into the well; initiate count of the pump strokes of the positive displacement mud pump as the previous step occurs; observe arrival of the identifiable material atmore » the surface of the earth as the drilling mud exits from the well; observe the accumulated count of the pump strokes of the positive displacement mud pump which occur between step one and step three; subtract, from the accumulated count of the previous step, the number of pump strokes of the positive displacement mud pump required to pump the identifiable material down to the drill bit to establish a number of lag strokes; and utilize the number obtained in the previous step to identify the arrival of drill cuttings from a predetermined depth.« less

Boron-rich mud volcanoes of the Black Sea region: modern analogues to ancient sea-floor tourmalinites associated with Sullivan-type Pb-Zn deposits?

USGS Publications Warehouse

Slack, J.F.; Turner, R.J.W.; Ware, P.L.G.

1998-01-01

Large submarine mud volcanoes in the abyssal part of the Black Sea south of the Crimean Peninsula are similar in many respects to synsedimentary mud volcanoes in the Mesoproterozoic Belt-Purcell basin. One of the Belt-Purcell mud volcanoes directly underlies the giant Sullivan Pb-Zn-Ag deposit in southeastern British Columbia. Footwall rocks to the Sullivan deposit comprise variably tourmalinized siltstone, conglomerate, and related fragmental rock; local thin pyrrhotite-rich and spessartine-quartz beds are interpreted as Fe and Fe-Mn exhalites, respectively. Analogous Fe- and Mn-rich sediments occur near the abyssal Black Sea mud volcanoes. Massive pyrite crusts and associated carbonate chimneys discovered in relatively shallow waters (~200 m depth) west of the Crimean Peninsula indicate an active sea-floor-hydrothermal system. Subaerial mud volcanoes on the Kerch and Taman Peninsulas (~100 km north of the abyssal mud volcanoes) contain saline thermal waters that locally have very high B contents (to 915 mg/L). These data suggest that tourmalinites might be forming in or near submarine Black Sea mud volcanoes, where potential may also exist for Sullivan-type Pb-Zn mineralization.

Geochemical recovery of the Torna-Marcal river system after the Ajka red mud spill, Hungary.

PubMed

Anton, Á D; Klebercz, O; Magyar, Á; Burke, I T; Jarvis, A P; Gruiz, K; Mayes, W M

2014-12-01

The failure of the Ajka red mud depository in October 2010 led to the largest single release of red mud into the surface water environment. This study provides a comparative assessment of stream sediment quality in the Torna-Marcal-Rába catchment between post-disaster surveys (2010) and follow up surveys at an identical suite of 21 locations in 2013. The signature of red mud apparent in initial surveys with high Al, As, Cr, Na, V was only apparent at a small number of sample stations in recent surveys. These constitute <1 km of stream, compared to the >20 km reach of affected sediments in the immediate aftermath of the spill. Concentrations of red mud-derived contaminants are predominately associated with fine fractions of the red mud (<8 μm). This enhances transport out of the system of red mud-derived contaminants and, along with extensive remedial efforts, has substantially limited the within-channel inventory of potentially ecotoxic metals and metalloids.

Calcification-carbonation method for red mud processing.

PubMed

Li, Ruibing; Zhang, Tingan; Liu, Yan; Lv, Guozhi; Xie, Liqun

2016-10-05

Red mud, the Bayer process residue, is generated from alumina industry and causes environmental problem. In this paper, a novel calcification-carbonation method that utilized a large amount of the Bayer process residue is proposed. Using this method, the red mud was calcified with lime to transform the silicon phase into hydrogarnet, and the alkali in red mud was recovered. Then, the resulting hydrogarnet was decomposed by CO2 carbonation, affording calcium silicate, calcium carbonate, and aluminum hydroxide. Alumina was recovered using an alkaline solution at a low temperature. The effects of the new process were analyzed by thermodynamics analysis and experiments. The extraction efficiency of the alumina and soda obtained from the red mud reached 49.4% and 96.8%, respectively. The new red mud with <0.3% alkali can be used in cement production. Using a combination of this method and cement production, the Bayer process red mud can be completely utilized. Copyright © 2016 Elsevier B.V. All rights reserved.

Resources Management Strategy For Mud Crabs (Scylla spp.) In Pemalang Regency

NASA Astrophysics Data System (ADS)

Purnama Fitri, Aristi Dian; Boesono, Herry; Sabdono, Agus; Adlina, Nadia

2017-02-01

The aim of this research is to develop resources management strategies of mud crab (Scylla spp.) in Pemalang Regency. The method used is descriptive survey in a case study. This research used primary data and secondary data. Primary data were collected through field observations and in-depth interviews with key stakeholders. Secondary data were collected from related publications and documents issued by the competent institutions. SWOT Analysis was used to inventory the strengths, weaknesses, opportunities and threats. TOWS matrix was used to develop an alternative of resources management strategies. SWOT analysis was obtained by 6 alternative strategies that can be applied for optimization of fisheries development in Pemalang Regency. The strategies is the control of mud crab fishing gear, restricted size allowable in mud crab, control of mud crab fishing season, catch monitoring of mud crab, needs a management institutions which ensure the implementation of the regulation, and implementation for mud crab aquaculture. Each alternative strategy can be synergized to optimize the resources development in Pemalang Regency.