Voltage-Load Sensitivity Matrix Based Demand Response for Voltage Control in High Solar Penetration Distribution Feeders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhu, Xiangqi; Wang, Jiyu; Mulcahy, David

This paper presents a voltage-load sensitivity matrix (VLSM) based voltage control method to deploy demand response resources for controlling voltage in high solar penetration distribution feeders. The IEEE 123-bus system in OpenDSS is used for testing the performance of the preliminary VLSM-based voltage control approach. A load disaggregation process is applied to disaggregate the total load profile at the feeder head to each load nodes along the feeder so that loads are modeled at residential house level. Measured solar generation profiles are used in the simulation to model the impact of solar power on distribution feeder voltage profiles. Different casemore » studies involving various PV penetration levels and installation locations have been performed. Simulation results show that the VLSM algorithm performance meets the voltage control requirements and is an effective voltage control strategy.« less

Distribution Feeder Modeling for Time-Series Simulation of Voltage Management Strategies: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giraldez Miner, Julieta I; Gotseff, Peter; Nagarajan, Adarsh

This paper presents techniques to create baseline distribution models using a utility feeder from Hawai'ian Electric Company. It describes the software-to-software conversion, steady-state, and time-series validations of a utility feeder model. It also presents a methodology to add secondary low-voltage circuit models to accurately capture the voltage at the customer meter level. This enables preparing models to perform studies that simulate how customer-sited resources integrate into legacy utility distribution system operations.

Methods to Determine Recommended Feeder-Wide Advanced Inverter Settings for Improving Distribution System Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rylander, Matthew; Reno, Matthew J.; Quiroz, Jimmy E.

This paper describes methods that a distribution engineer could use to determine advanced inverter settings to improve distribution system performance. These settings are for fixed power factor, volt-var, and volt-watt functionality. Depending on the level of detail that is desired, different methods are proposed to determine single settings applicable for all advanced inverters on a feeder or unique settings for each individual inverter. Seven distinctly different utility distribution feeders are analyzed to simulate the potential benefit in terms of hosting capacity, system losses, and reactive power attained with each method to determine the advanced inverter settings.

A Review of Distributed Control Techniques for Power Quality Improvement in Micro-grids

NASA Astrophysics Data System (ADS)

Zeeshan, Hafiz Muhammad Ali; Nisar, Fatima; Hassan, Ahmad

2017-05-01

Micro-grid is typically visualized as a small scale local power supply network dependent on distributed energy resources (DERs) that can operate simultaneously with grid as well as in standalone manner. The distributed generator of a micro-grid system is usually a converter-inverter type topology acting as a non-linear load, and injecting harmonics into the distribution feeder. Hence, the negative effects on power quality by the usage of distributed generation sources and components are clearly witnessed. In this paper, a review of distributed control approaches for power quality improvement is presented which encompasses harmonic compensation, loss mitigation and optimum power sharing in multi-source-load distributed power network. The decentralized subsystems for harmonic compensation and active-reactive power sharing accuracy have been analysed in detail. Results have been validated to be consistent with IEEE standards.

Cost Benefit and Alternatives Analysis of Distribution Systems with Energy Storage Systems: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, Tom; Nagarajan, Adarsh; Baggu, Murali

This paper explores monetized and non-monetized benefits from storage interconnected to distribution system through use cases illustrating potential applications for energy storage in California's electric utility system. This work supports SDG&E in its efforts to quantify, summarize, and compare the cost and benefit streams related to implementation and operation of energy storage on its distribution feeders. This effort develops the cost benefit and alternatives analysis platform, integrated with QSTS feeder simulation capability, and analyzed use cases to explore the cost-benefit of implementation and operation of energy storage for feeder support and market participation.

An Incentive-based Online Optimization Framework for Distribution Grids

DOE PAGES

Zhou, Xinyang; Dall'Anese, Emiliano; Chen, Lijun; ...

2017-10-09

This article formulates a time-varying social-welfare maximization problem for distribution grids with distributed energy resources (DERs) and develops online distributed algorithms to identify (and track) its solutions. In the considered setting, network operator and DER-owners pursue given operational and economic objectives, while concurrently ensuring that voltages are within prescribed limits. The proposed algorithm affords an online implementation to enable tracking of the solutions in the presence of time-varying operational conditions and changing optimization objectives. It involves a strategy where the network operator collects voltage measurements throughout the feeder to build incentive signals for the DER-owners in real time; DERs thenmore » adjust the generated/consumed powers in order to avoid the violation of the voltage constraints while maximizing given objectives. Stability of the proposed schemes is analytically established and numerically corroborated.« less

An Incentive-based Online Optimization Framework for Distribution Grids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhou, Xinyang; Dall'Anese, Emiliano; Chen, Lijun

This article formulates a time-varying social-welfare maximization problem for distribution grids with distributed energy resources (DERs) and develops online distributed algorithms to identify (and track) its solutions. In the considered setting, network operator and DER-owners pursue given operational and economic objectives, while concurrently ensuring that voltages are within prescribed limits. The proposed algorithm affords an online implementation to enable tracking of the solutions in the presence of time-varying operational conditions and changing optimization objectives. It involves a strategy where the network operator collects voltage measurements throughout the feeder to build incentive signals for the DER-owners in real time; DERs thenmore » adjust the generated/consumed powers in order to avoid the violation of the voltage constraints while maximizing given objectives. Stability of the proposed schemes is analytically established and numerically corroborated.« less

IEEE 342 Node Low Voltage Networked Test System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, Kevin P.; Phanivong, Phillippe K.; Lacroix, Jean-Sebastian

The IEEE Distribution Test Feeders provide a benchmark for new algorithms to the distribution analyses community. The low voltage network test feeder represents a moderate size urban system that is unbalanced and highly networked. This is the first distribution test feeder developed by the IEEE that contains unbalanced networked components. The 342 node Low Voltage Networked Test System includes many elements that may be found in a networked system: multiple 13.2kV primary feeders, network protectors, a 120/208V grid network, and multiple 277/480V spot networks. This paper presents a brief review of the history of low voltage networks and how theymore » evolved into the modern systems. This paper will then present a description of the 342 Node IEEE Low Voltage Network Test System and power flow results.« less

Technologies to Increase PV Hosting Capacity in Distribution Feeders: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Fei; Mather, Barry; Gotseff, Peter

This paper studies the distributed photovoltaic (PV) hosting capacity in distribution feeders by using the stochastic analysis approach. Multiple scenario simulations are conducted to analyze several factors that affect PV hosting capacity, including the existence of voltage regulator, PV location, the power factor of PV inverter and Volt/VAR control. Based on the conclusions obtained from simulation results, three approaches are then proposed to increase distributed PV hosting capacity, which can be formulated as the optimization problem to obtain the optimal solution. All technologies investigated in this paper utilize only existing assets in the feeder and therefore are implementable for amore » low cost. Additionally, the tool developed for these studies is described.« less

Technologies to Increase PV Hosting Capacity in Distribution Feeders

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Fei; Mather, Barry; Gotseff, Peter

This paper studies the distributed photovoltaic (PV) hosting capacity in distribution feeders by using the stochastic analysis approach. Multiple scenario simulations are conducted to analyze several factors that affect PV hosting capacity, including the existence of voltage regulator, PV location, the power factor of PV inverter and Volt/VAR control. Based on the conclusions obtained from simulation results, three approaches are then proposed to increase distributed PV hosting capacity, which can be formulated as the optimization problem to obtain the optimal solution. All technologies investigated in this paper utilize only existing assets in the feeder and therefore are implementable for amore » low cost. Additionally, the tool developed for these studies is described.« less

Voltage Impacts of Utility-Scale Distributed Wind

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen, A.

2014-09-01

Although most utility-scale wind turbines in the United States are added at the transmission level in large wind power plants, distributed wind power offers an alternative that could increase the overall wind power penetration without the need for additional transmission. This report examines the distribution feeder-level voltage issues that can arise when adding utility-scale wind turbines to the distribution system. Four of the Pacific Northwest National Laboratory taxonomy feeders were examined in detail to study the voltage issues associated with adding wind turbines at different distances from the sub-station. General rules relating feeder resistance up to the point of turbinemore » interconnection to the expected maximum voltage change levels were developed. Additional analysis examined line and transformer overvoltage conditions.« less

Power System Simulation for Policymaking and Making Policymakers

NASA Astrophysics Data System (ADS)

Cohen, Michael Ari

Power system simulation is a vital tool for anticipating, planning for and ultimately addressing future conditions on the power grid, especially in light of contemporary shifts in power generation, transmission and use that are being driven by a desire to utilize more environmentally responsible energy sources. This dissertation leverages power system simulation and engineering-economic analysis to provide initial answers to one open question about future power systems: how will high penetrations of distributed (rooftop) solar power affect the physical and economic operation of distribution feeders? We find that the overall impacts of distributed solar power (both positive and negative) on the feeders we modeled are minor compared to the overall cost of energy, but that there is on average a small net benefit provided by distributed generation. We then describe an effort to make similar analyses more accessible to a non-engineering (high school) audience by developing an educational video game called "Griddle" that is based on the same power system simulation techniques used in the first study. We describe the design and evaluation of Griddle and find that it demonstrates potential to provide students with insights about key power system learning objectives.

Faculty Articulation with Feeder High Schools and Local Employers.

ERIC Educational Resources Information Center

Parrott, Marietta

As a first step in developing an articulation plan with feeder high schools, a College of the Sequoias (COS) task force developed and distributed a survey to all full-time faculty members to determine if individual faculty members were articulating with feeder high schools and local businesses, and if they would be willing to participate in an…

Impacts of Using Distributed Energy Resources to Reduce Peak Loads in Vermont

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruth, Mark F.; Lunacek, Monte S.; Jones, Birk

To help the United States develop a modern electricity grid that provides reliable power from multiple resources as well as resiliency under extreme conditions, the U.S. Department of Energy (DOE) is leading the Grid Modernization Initiative (GMI) to help shape the future of the nation's grid. Under the GMI, DOE funded the Vermont Regional Initiative project to provide the technical support and analysis to utilities that need to mitigate possible impacts of increasing renewable generation required by statewide goals. Advanced control of distributed energy resources (DER) can both support higher penetrations of renewable energy by balancing controllable loads to windmore » and photovoltaic (PV) solar generation and reduce peak demand by shedding noncritical loads. This work focuses on the latter. This document reports on an experiment that evaluated and quantified the potential benefits and impacts of reducing the peak load through demand response (DR) using centrally controllable electric water heaters (EWHs) and batteries on two Green Mountain Power (GMP) feeders. The experiment simulated various hypothetical scenarios that varied the number of controllable EWHs, the amount of distributed PV systems, and the number of distributed residential batteries. The control schemes were designed with several objectives. For the first objective, the primary simulations focused on reducing the load during the independent system operator (ISO) peak when capacity charges were the primary concern. The second objective was to mitigate DR rebound to avoid new peak loads and high ramp rates. The final objective was to minimize customers' discomfort, which is defined by the lack of hot water when it is needed. We performed the simulations using the National Renewable Energy Laboratory's (NREL's) Integrated Energy System Model (IESM) because it can simulate both electric power distribution feeder and appliance end use performance and it includes the ability to simulate multiple control strategies.« less

Preliminary evaluation of feeder and lint slide moisture addition on ginning, fiber quality, and textile processing of western cotton

USDA-ARS?s Scientific Manuscript database

The objective of this study was to evaluate the effects of moisture addition at the gin stand feeder conditioning hopper and/or the battery condenser slide on gin performance and Western cotton fiber quality and textile processing. The test treatments included no moisture addition, feeder hopper hum...

Intelligent Distribution Voltage Control with Distributed Generation =

NASA Astrophysics Data System (ADS)

Castro Mendieta, Jose

In this thesis, three methods for the optimal participation of the reactive power of distributed generations (DGs) in unbalanced distributed network have been proposed, developed, and tested. These new methods were developed with the objectives of maintain voltage within permissible limits and reduce losses. The first method proposes an optimal participation of reactive power of all devices available in the network. The propose approach is validated by comparing the results with other methods reported in the literature. The proposed method was implemented using Simulink of Matlab and OpenDSS. Optimization techniques and the presentation of results are from Matlab. The co-simulation of Electric Power Research Institute's (EPRI) OpenDSS program solves a three-phase optimal power flow problem in the unbalanced IEEE 13 and 34-node test feeders. The results from this work showed a better loss reduction compared to the Coordinated Voltage Control (CVC) method. The second method aims to minimize the voltage variation on the pilot bus on distribution network using DGs. It uses Pareto and Fuzzy-PID logic to reduce the voltage variation. Results indicate that the proposed method reduces the voltage variation more than the other methods. Simulink of Matlab and OpenDSS is used in the development of the proposed approach. The performance of the method is evaluated on IEEE 13-node test feeder with one and three DGs. Variables and unbalanced loads are used, based on real consumption data, over a time window of 48 hours. The third method aims to minimize the reactive losses using DGs on distribution networks. This method analyzes the problem using the IEEE 13-node test feeder with three different loads and the IEEE 123-node test feeder with four DGs. The DGs can be fixed or variables. Results indicate that integration of DGs to optimize the reactive power of the network helps to maintain the voltage within the allowed limits and to reduce the reactive power losses. The thesis is presented in the form of the three articles. The first article is published in the journal Electrical Power and Energy System, the second is published in the international journal Energies and the third was submitted to the journal Electrical Power and Energy System. Two other articles have been published in conferences with reviewing committee. This work is based on six chapters, which are detailed in the various sections of the thesis.

Impact of Distribution Feeders that do not have Voltage Regulators on the number of Charged Electric Vehicles using IEEE 34 Bus Test Feeder

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allehyani, Ahmed; Beshir, Mohammed

Voltage regulators help maintain an acceptable voltage profile for the system. This paper discusses the effect of installing voltage regulators to the system to fix the voltage drop resulting from the electrical vehicles loading increase when they are being charged. The effect will be studied in the afternoon, when the peak load occurs, using the IEEE 34 bus test feeder. First, only one spot node is used to charge the electric vehicles while a voltage regulator is present. Second, five spot nodes are loaded at the same time to charge the electric vehicles while voltage regulators are installed at eachmore » node. After that, the impact of electric vehicles on distribution feeders that do not have voltage regulators will appear.« less

Coordinated Optimization of Distributed Energy Resources and Smart Loads in Distribution Systems: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Rui; Zhang, Yingchen

2016-08-01

Distributed energy resources (DERs) and smart loads have the potential to provide flexibility to the distribution system operation. A coordinated optimization approach is proposed in this paper to actively manage DERs and smart loads in distribution systems to achieve the optimal operation status. A three-phase unbalanced Optimal Power Flow (OPF) problem is developed to determine the output from DERs and smart loads with respect to the system operator's control objective. This paper focuses on coordinating PV systems and smart loads to improve the overall voltage profile in distribution systems. Simulations have been carried out in a 12-bus distribution feeder andmore » results illustrate the superior control performance of the proposed approach.« less

Coordinated Optimization of Distributed Energy Resources and Smart Loads in Distribution Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Rui; Zhang, Yingchen

2016-11-14

Distributed energy resources (DERs) and smart loads have the potential to provide flexibility to the distribution system operation. A coordinated optimization approach is proposed in this paper to actively manage DERs and smart loads in distribution systems to achieve the optimal operation status. A three-phase unbalanced Optimal Power Flow (OPF) problem is developed to determine the output from DERs and smart loads with respect to the system operator's control objective. This paper focuses on coordinating PV systems and smart loads to improve the overall voltage profile in distribution systems. Simulations have been carried out in a 12-bus distribution feeder andmore » results illustrate the superior control performance of the proposed approach.« less

Multi-Time Step Service Restoration for Advanced Distribution Systems and Microgrids

DOE PAGES

Chen, Bo; Chen, Chen; Wang, Jianhui; ...

2017-07-07

Modern power systems are facing increased risk of disasters that can cause extended outages. The presence of remote control switches (RCSs), distributed generators (DGs), and energy storage systems (ESS) provides both challenges and opportunities for developing post-fault service restoration methodologies. Inter-temporal constraints of DGs, ESS, and loads under cold load pickup (CLPU) conditions impose extra complexity on problem formulation and solution. In this paper, a multi-time step service restoration methodology is proposed to optimally generate a sequence of control actions for controllable switches, ESSs, and dispatchable DGs to assist the system operator with decision making. The restoration sequence is determinedmore » to minimize the unserved customers by energizing the system step by step without violating operational constraints at each time step. The proposed methodology is formulated as a mixed-integer linear programming (MILP) model and can adapt to various operation conditions. Furthermore, the proposed method is validated through several case studies that are performed on modified IEEE 13-node and IEEE 123-node test feeders.« less

Multi-Time Step Service Restoration for Advanced Distribution Systems and Microgrids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Bo; Chen, Chen; Wang, Jianhui

Modern power systems are facing increased risk of disasters that can cause extended outages. The presence of remote control switches (RCSs), distributed generators (DGs), and energy storage systems (ESS) provides both challenges and opportunities for developing post-fault service restoration methodologies. Inter-temporal constraints of DGs, ESS, and loads under cold load pickup (CLPU) conditions impose extra complexity on problem formulation and solution. In this paper, a multi-time step service restoration methodology is proposed to optimally generate a sequence of control actions for controllable switches, ESSs, and dispatchable DGs to assist the system operator with decision making. The restoration sequence is determinedmore » to minimize the unserved customers by energizing the system step by step without violating operational constraints at each time step. The proposed methodology is formulated as a mixed-integer linear programming (MILP) model and can adapt to various operation conditions. Furthermore, the proposed method is validated through several case studies that are performed on modified IEEE 13-node and IEEE 123-node test feeders.« less

Preliminary analysis of hub and spoke air freight distribution system

NASA Technical Reports Server (NTRS)

Whitehead, A. H., Jr.

1978-01-01

A brief analysis is made of the hub and spoke air freight distribution system which would employ less than 15 hub centers world wide with very large advanced distributed-load freighters providing the line-haul delivery between hubs. This system is compared to a more conventional network using conventionally-designed long-haul freighters which travel between numerous major airports. The analysis calculates all of the transportation costs, including handling charges and pickup and delivery costs. The results show that the economics of the hub/spoke system are severely compromised by the extensive use of feeder aircraft to deliver cargo into and from the large freighter terminals. Not only are the higher costs for the smaller feeder airplanes disadvantageous, but their use implies an additional exchange of cargo between modes compared to truck delivery. The conventional system uses far fewer feeder airplanes, and in many cases, none at all. When feeder aircraft are eliminated from the hub/spoke system, however, that system is universally more economical than any conventional system employing smaller line-haul aircraft.

Alternatives to the 15% Rule

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broderick, Robert Joseph; Quiroz, Jimmy Edward; Reno, Matthew J.

2015-11-01

The third solicitation of the California Solar Initiative (CSI) Research, Development, Demonstration and Deployment (RD&D) Program established by the California Public Utility Commission (CPUC) is supporting the Electric Power Research Institute (EPRI), National Renewable Energy Laboratory (NREL), and Sandia National Laboratories (SNL) with collaboration from Pacific Gas and Electric (PG&E), Southern California Edison (SCE), and San Diego Gas and Electric (SDG&E), in research to improve the Utility Application Review and Approval process for interconnecting distributed energy resources to the distribution system. Currently this process is the most time - consuming of any step on the path to generating power onmore » the distribution system. This CSI RD&D solicitation three project has completed the tasks of collecting data from the three utilities, clustering feeder characteristic data to attain representative feeders, detailed modeling of 16 representative feeders, analysis of PV impacts to those feeders, refinement of current screening processes, and validation of those suggested refinements. In this report each task is summarized to produce a final summary of all components of the overall project.« less

Object categorization by wild ranging birds-Winter feeder experiments.

PubMed

Nováková, Nela; Veselý, Petr; Fuchs, Roman

2017-10-01

The object categorization is only scarcely studied using untrained wild ranging animals and relevant stimuli. We tested the importance of the spatial position of features salient for categorization of a predator using wild ranging birds (titmice) visiting a winter feeder. As a relevant stimulus we used a dummy of a raptor, the European sparrowhawk (Accipiter nisus), placed at the feeding location. This dummy was designed to be dismantled into three parts and rearranged with the head in the correct position, in the middle or at the bottom of the dummy. When the birds had the option of visiting an alternative feeder with a dummy pigeon, they preferred this option to visiting the feeder with the dummy sparrowhawk with the head in any of the three positions. When the birds had the option of visiting an alternative feeder with an un-rearranged dummy sparrowhawk, they visited both feeders equally often, and very scarcely. This suggests that the titmice considered all of the sparrowhawk modifications as being dangerous, and equally dangerous as the un-rearranged sparrowhawk. The position of the head was not the most important cue for categorization. The presence of the key features was probably sufficient for categorization, and their mutual spatial position was of lower importance. Copyright © 2017 Elsevier B.V. All rights reserved.

Analysis of broadcasting satellite service feeder link power control and polarization

NASA Technical Reports Server (NTRS)

Sullivan, T. M.

1982-01-01

Statistical analyses of carrier to interference power ratios (C/Is) were performed in assessing 17.5 GHz feeder links using (1) fixed power and power control, and (2) orthogonal linear and orthogonal circular polarizations. The analysis methods and attenuation/depolarization data base were based on CCIR findings to the greatest possible extent. Feeder links using adaptive power control were found to neither cause or suffer significant C/I degradation relative to that for fixed power feeder links having similar or less stringent availability objectives. The C/Is for sharing between orthogonal linearly polarized feeder links were found to be significantly higher than those for circular polarization only in links to nominally colocated satellites from nominally colocated Earth stations in high attenuation environments.

Method and apparatus for anti-islanding protection of distributed generations

DOEpatents

Ye, Zhihong; John, Vinod; Wang, Changyong; Garces, Luis Jose; Zhou, Rui; Li, Lei; Walling, Reigh Allen; Premerlani, William James; Sanza, Peter Claudius; Liu, Yan; Dame, Mark Edward

2006-03-21

An apparatus for anti-islanding protection of a distributed generation with respect to a feeder connected to an electrical grid is disclosed. The apparatus includes a sensor adapted to generate a voltage signal representative of an output voltage and/or a current signal representative of an output current at the distributed generation, and a controller responsive to the signals from the sensor. The controller is productive of a control signal directed to the distributed generation to drive an operating characteristic of the distributed generation out of a nominal range in response to the electrical grid being disconnected from the feeder.

The Cost of Distribution System Upgrades to Accommodate Increasing Penetrations of Distributed Photovoltaic Systems on Real Feeders in the United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horowitz, Kelsey A; Ding, Fei; Mather, Barry A

The increasing deployment of distributed photovoltaic systems (DPV) can impact operations at the distribution level and the transmission level of the electric grid. It is important to develop and implement forward-looking approaches for calculating distribution upgrade costs that can be used to inform system planning, market and tariff design, cost allocation, and other policymaking as penetration levels of DPV increase. Using a bottom-up approach that involves iterative hosting capacity analysis, this report calculates distribution upgrade costs as a function of DPV penetration on three real feeders - two in California and one in the Northeastern United States.

System Operations Studies : Feeder System Model. User's Manual.

DOT National Transportation Integrated Search

1982-11-01

The Feeder System Model (FSM) is one of the analytic models included in the System Operations Studies (SOS) software package developed for urban transit systems analysis. The objective of the model is to assign a proportion of the zone-to-zone travel...

Functional and aesthetic approach to design of bird feeders

NASA Astrophysics Data System (ADS)

Kukhta, A.; Kukhta, M.

2015-10-01

Anthropogenic objects which load the urban environment negatively affects the human psyche. The alternative is attracting elements of the natural environment into urban environment, of which some of the most frequently identified are birds. Attracting birds in the city is possible by means of feeders and artificial nests, however, both must be harmonious. The aim of this study is to analyze the essential functions of the feeders, and their integration into the environmental design and development of the city. On this basis an original feeder which is convenient for use by birds and attracts people's attention is developed. In this paper we apply comparative analysis of different types of feeders encountered in Tomsk, bird watching, and evaluate usability of different types of feeders from the position of their convenience both for birds and human beings. Historical-cultural analysis for determining features of the architectural and environmental design of Tomsk is carried out, the method allows us to solve engineering problems. In this study the feeder convenient for bird use is designed which blends harmoniously with the architectural design of Tomsk.

RF model of the distribution system as a communication channel, phase 2. Volume 2: Task reports

NASA Technical Reports Server (NTRS)

Rustay, R. C.; Gajjar, J. T.; Rankin, R. W.; Wentz, R. C.; Wooding, R.

1982-01-01

Based on the established feasibility of predicting, via a model, the propagation of Power Line Frequency on radial type distribution feeders, verification studies comparing model predictions against measurements were undertaken using more complicated feeder circuits and situations. Detailed accounts of the major tasks are presented. These include: (1) verification of model; (2) extension, implementation, and verification of perturbation theory; (3) parameter sensitivity; (4) transformer modeling; and (5) compensation of power distribution systems for enhancement of power line carrier communication reliability.

Zooplankton Distribution in Four Western Norwegian Fjords

NASA Astrophysics Data System (ADS)

Gorsky, G.; Flood, P. R.; Youngbluth, M.; Picheral, M.; Grisoni, J.-M.

2000-01-01

A multi-instrumental array constructed in the Laboratoire d'Ecologie du Plancton Marin in Villefranche sur mer, France, named the Underwater Video Profiler (UVP), was used to investigate the vertical distribution of zooplankton in four western Norwegian fjords in the summer 1996. Six distinct zoological groups were monitored. The fauna included: (a) small crustaceans (mainly copepods), (b) ctenophores (mainly lobates), (c) siphonophores (mainly physonects), (d) a scyphomedusa Periphylla periphylla, (e) chaetognaths and (f) appendicularians. The use of the non-disturbing video technique demonstrated that the distribution of large zooplankton is heterogeneous vertically and geographically. Furthermore, the abundance of non-migrating filter feeders in the deep basins of the fjords indicates that there is enough food (living and non-living particulate organic matter) to support their dietary needs. This adaptation may be considered as a strategy for survival in fjords. Specifically, living in dark, deep water reduces visual predation and population loss encountered in the upper layer due to advective processes.

Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagarajan, Adarsh; Nelson, Austin A; Prabakar, Kumaraguru

As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time simulators and test PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a ruin & reconstruct methodology that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-timemore » digital testing platform. Smart PV inverters were added to the realtime model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the feeders could be analyzed.« less

Network Reduction Algorithm for Developing Distribution Feeders for Real-Time Simulators: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagarajan, Adarsh; Nelson, Austin; Prabakar, Kumaraguru

As advanced grid-support functions (AGF) become more widely used in grid-connected photovoltaic (PV) inverters, utilities are increasingly interested in their impacts when implemented in the field. These effects can be understood by modeling feeders in real-time systems and testing PV inverters using power hardware-in-the-loop (PHIL) techniques. This paper presents a novel feeder model reduction algorithm using a Monte Carlo method that enables large feeders to be solved and operated on real-time computing platforms. Two Hawaiian Electric feeder models in Synergi Electric's load flow software were converted to reduced order models in OpenDSS, and subsequently implemented in the OPAL-RT real-time digitalmore » testing platform. Smart PV inverters were added to the real-time model with AGF responses modeled after characterizing commercially available hardware inverters. Finally, hardware inverters were tested in conjunction with the real-time model using PHIL techniques so that the effects of AGFs on the choice feeders could be analyzed.« less

Round-bale feeder design affects hay waste and economics during horse feeding.

PubMed

Martinson, K; Wilson, J; Cleary, K; Lazarus, W; Thomas, W; Hathaway, M

2012-03-01

Many horse owners find round bales convenient, less labor intensive, and more affordable than other hay types, but report an inability to control horse BW gain and excessive hay waste. The objectives were to compare hay waste, hay intake, and payback of 9 round-bale feeders and a no-feeder control when used during horse feeding. Nine round-bale feeders were tested: Cinch Net, Cone, Covered Cradle, Hayhut, Hay Sleigh, Ring, Tombstone, Tombstone Saver, and Waste Less. Each feeder design was placed on the ground in a dirt paddock. Five groups of 5 horses were fed in rotation for a 4-d period with each feeder. Every fourth day, groups were rotated among paddocks and a new round bale was placed in each feeder. In the 5 paddocks used, 5 feeders were installed for d 1 through 20, and the remaining 4 feeders and no-feeder control were installed for d 21 through 40. Groups of horses were sequentially assigned to feeders using two 5 × 5 Latin squares, the first for d 1 through 20, the second for d 21 through 40. Horse groups of similar age, BW, breed, and sex were formed from 25 Quarter Horse and Thoroughbred geldings and open mares (means: 11 yr; 541 kg of BW). Hay on the ground surrounding the feeder was collected daily, dried, and weighed. The total amount of hay removed around each feeder for a 4-d period was considered waste. Dry matter intake was estimated as the difference between hay disappearance and waste. Number of months for the reduction in waste to repay feeder cost (payback) were calculated using hay valued at $110/t, and improved feeder efficiency over the control. Feeder design did not affect hay intake (P > 0.05); all feeders resulted in an estimated hay intake of 2.0 to 2.4% BW; the no-feeder control resulted in a reduced intake of 1.3% BW (P = 0.001). Mean percentage of hay waste differed among feeders (P < 0.001): Waste Less, 5%; Cinch Net, 6%; Hayhut, 9%; Covered Cradle, 11%; Tombstone Saver, 13%; Tombstone, Cone, and Ring, 19%; Hay Sleigh, 33%; and no-feeder control, 57%. Feeder design also affected payback (P < 0.01). The Cinch Net paid for itself in less than 1 mo; Tombstone and Ring, 2 mo; Hayhut and Tombstone Saver, 4 mo; Hay Sleigh, 5 mo; Waste Less, 8 mo; Cone, 9 mo; and Covered Cradle, 20 mo. Round-bale feeder design affected hay waste and payback, but not estimated hay intake or BW change during horse feeding.

Tumorigenic risk of human induced pluripotent stem cell explants cultured on mouse SNL76/7 feeder cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kamada, Mizuna; Mitsui, Youji, E-mail: y-mitsui8310@hb.tp1.jp; Kumazaki, Tsutomu

2014-10-24

Highlights: • hiPS cell explants formed malignant tumors when SNL76/7 feeder cells were used. • Multi type tumors developed by interaction of SNL76/7 feeder cells with hiPS cells. • Tumorigenic risk occurs by co-culture of hiPS cells with SNL76/7 feeder cells. - Abstract: The potential for tumor formation from transplanted human induced pluripotent stem cell (hiPSC) derivatives represents a high risk in their application to regenerative medicine. We examined the genetic origin and characteristics of tumors, that were formed when 13 hiPSC lines, established by ourselves, and 201B7 hiPSC from Kyoto University were transplanted into severe combined immune-deficient (SCID) mice.more » Though teratomas formed in 58% of mice, five angiosarcomas, one malignant solitary fibrous tumor and one undifferentiated pleomorphic sarcoma formed in the remaining mice. Three malignant cell lines were established from the tumors, which were derived from mitomycin C (MMC)-treated SNL76/7 (MMC-SNL) feeder cells, as tumor development from fusion cells between MMC-SNL and hiPSCs was negative by genetic analysis. While parent SNL76/7 cells produced malignant tumors, neither MMC-SNL nor MMC-treated mouse embryo fibroblast (MEF) produced malignant tumors. When MMC-SNL feeder cells were co-cultured with hiPSCs, growing cell lines were generated, that expressed genes similar to the parent SNL76/7 cells. Thus, hiPSCs grown on MMC-SNL feeder cells have a high risk of generating feeder-derived malignant tumors. The possible mechanism(s) of growth restoration and the formation of multiple tumor types are discussed with respect of the interactions between MMC-SNL and hiPSC.« less

Systems Operation Studies for Automated Guideway Transit Systems: Feeder Systems Model Functional Specification

DOT National Transportation Integrated Search

1981-01-01

This document specifies the functional requirements for the AGT-SOS Feeder Systems Model (FSM), the type of hardware required, and the modeling techniques employed by the FSM. The objective of the FSM is to map the zone-to-zone transit patronage dema...

Distributed Generation Planning using Peer Enhanced Multi-objective Teaching-Learning based Optimization in Distribution Networks

NASA Astrophysics Data System (ADS)

Selvam, Kayalvizhi; Vinod Kumar, D. M.; Siripuram, Ramakanth

2017-04-01

In this paper, an optimization technique called peer enhanced teaching learning based optimization (PeTLBO) algorithm is used in multi-objective problem domain. The PeTLBO algorithm is parameter less so it reduced the computational burden. The proposed peer enhanced multi-objective based TLBO (PeMOTLBO) algorithm has been utilized to find a set of non-dominated optimal solutions [distributed generation (DG) location and sizing in distribution network]. The objectives considered are: real power loss and the voltage deviation subjected to voltage limits and maximum penetration level of DG in distribution network. Since the DG considered is capable of injecting real and reactive power to the distribution network the power factor is considered as 0.85 lead. The proposed peer enhanced multi-objective optimization technique provides different trade-off solutions in order to find the best compromise solution a fuzzy set theory approach has been used. The effectiveness of this proposed PeMOTLBO is tested on IEEE 33-bus and Indian 85-bus distribution system. The performance is validated with Pareto fronts and two performance metrics (C-metric and S-metric) by comparing with robust multi-objective technique called non-dominated sorting genetic algorithm-II and also with the basic TLBO.

Influence of trophic variables on the depth-range distributions and zonation rates of deep-sea megafauna: the case of the Western Mediterranean assemblages

NASA Astrophysics Data System (ADS)

Cartes, Joan E.; Carrassón, Maite

2004-02-01

We studied in a deep-sea megafaunal community the relationship of different trophic variables to the depth ranges inhabited by and depth zonation of species, after the ordination of fish and decapod crustaceans in feeding guilds. The variables studied included trophic level of species, food sources exploited, mean weight of predators and prey, feeding intensity and dietary diversity of species. We compiled data on the diets of 18 species of fish and 14 species of decapod crustaceans distributed between 862 and 2261 m in the Catalano-Balearic Basin (Western Mediterranean). Feeding guilds were identified for fish and decapods separately and at two depth strata (862-1400 and 1400-2261 m). The zonation rates (degree of depth overlap) between species within each trophic guild differed by guild and taxon (fish and decapods). The three guilds (G1, G2 and G3) of decapod crustaceans showed quite significantly distinct overlap. G1 (plankton feeders) showed the widest overlap (1326-1381 m) and G3 (benthos feeders) the narrowest (330-476 m). Among the four guilds established for fish, G1, comprising larger predators such as sharks, showed the lowest overlap (between 194 and 382 m). Macrourids overlap ranged between 122 and 553 m, the rest of benthopelagic feeders ranged between 423 and 970 m, and G3 (benthos feeders) gave overlaps between 867 and 1067 m. Significant differences were detected between the depth overlap of most feeding guilds excluding the paired comparisons between G1/macrourids, and G2/G3. Among decapods higher zonation rates (=lower depth overlap) were identified in those guilds occupying higher trophic levels (TL), with a similar, though not as general, trend among fish. In the ordination of species in feeding guilds, TL as indicated by δ15N measurements, was significantly correlated with Dimension 1 (D1) of ordination—MDS-analysis, both in fish and decapods at 862-1400 m. However, deeper (at 1400-2261 m), D1 was not significantly correlated with TL but with the mean weight of predator and prey in fish. In general, TL was again the main explanatory variable (accumulated variances, r2, explained by multi-linear regression—MLR-models between 0.54 and 0.69) both of the zonation rates and the depth ranges occupied by megafauna (fish and decapods together) throughout all the depth range studied. Possible relationships between zonation rates /depth distributions and other biological variables (i.e. egg size, fecundity) are also discussed.

Optimal operation management of fuel cell/wind/photovoltaic power sources connected to distribution networks

NASA Astrophysics Data System (ADS)

Niknam, Taher; Kavousifard, Abdollah; Tabatabaei, Sajad; Aghaei, Jamshid

2011-10-01

In this paper a new multiobjective modified honey bee mating optimization (MHBMO) algorithm is presented to investigate the distribution feeder reconfiguration (DFR) problem considering renewable energy sources (RESs) (photovoltaics, fuel cell and wind energy) connected to the distribution network. The objective functions of the problem to be minimized are the electrical active power losses, the voltage deviations, the total electrical energy costs and the total emissions of RESs and substations. During the optimization process, the proposed algorithm finds a set of non-dominated (Pareto) optimal solutions which are stored in an external memory called repository. Since the objective functions investigated are not the same, a fuzzy clustering algorithm is utilized to handle the size of the repository in the specified limits. Moreover, a fuzzy-based decision maker is adopted to select the 'best' compromised solution among the non-dominated optimal solutions of multiobjective optimization problem. In order to see the feasibility and effectiveness of the proposed algorithm, two standard distribution test systems are used as case studies.

Chance-Constrained Day-Ahead Hourly Scheduling in Distribution System Operation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Huaiguang; Zhang, Yingchen; Muljadi, Eduard

This paper aims to propose a two-step approach for day-ahead hourly scheduling in a distribution system operation, which contains two operation costs, the operation cost at substation level and feeder level. In the first step, the objective is to minimize the electric power purchase from the day-ahead market with the stochastic optimization. The historical data of day-ahead hourly electric power consumption is used to provide the forecast results with the forecasting error, which is presented by a chance constraint and formulated into a deterministic form by Gaussian mixture model (GMM). In the second step, the objective is to minimize themore » system loss. Considering the nonconvexity of the three-phase balanced AC optimal power flow problem in distribution systems, the second-order cone program (SOCP) is used to relax the problem. Then, a distributed optimization approach is built based on the alternating direction method of multiplier (ADMM). The results shows that the validity and effectiveness method.« less

The science enabled by the Maunakea Spectroscopic Explorer

NASA Astrophysics Data System (ADS)

Martin, N. F.; Babusiaux, C.

2017-12-01

With its unique wide-field, multi-object, and dedicated spectroscopic capabilities, the Maunakea Spectroscopic Explorer (MSE) is a powerful facility to shed light on the faint Universe. Built around an upgrade of the Canada-France Hawaii Telescope (CFHT) to a 11.25-meter telescope with a dedicated ˜1.5 deg^2, 4,000-fiber wide-field spectrograph that covers the optical and near-infrared wavelengths at resolutions between 2,500 and 40,000, the MSE is the essential follow-up complement to the current and next generations of multi-wavelength imaging surveys, such as the LSST, Gaia, Euclid, eROSITA, SKA, and WFIRST, and is an ideal feeder facility for the extremely large telescopes that are currently being built (E-ELT, GMT, and TMT). The science enabled by the MSE is vast and would have an impact on almost all aspects of astronomy research.

Design and Scheduling of Microgrids using Benders Decomposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagarajan, Adarsh; Ayyanar, Raja

2016-11-21

The distribution feeder laterals in a distribution feeder with relatively high PV generation as compared to the load can be operated as microgrids to achieve reliability, power quality and economic benefits. However, renewable resources are intermittent and stochastic in nature. A novel approach for sizing and scheduling an energy storage system and microturbine for reliable operation of microgrids is proposed. The size and schedule of an energy storage system and microturbine are determined using Benders' decomposition, considering PV generation as a stochastic resource.

Energy Systems Integration News | Energy Systems Integration Facility |

Science.gov Websites

distribution feeder models for use in hardware-in-the-loop (HIL) experiments. Using this method, a full feeder ; proposes an additional control loop to improve frequency support while ensuring stable operation. The and Frequency Deviation," also proposes an additional control loop, this time to smooth the wind

Multi-Generational Kinship, Multiple Mating, and Flexible Modes of Parental Care in a Breeding Population of the Veery (Catharus fuscescens), a Trans-Hemispheric Migratory Songbird

PubMed Central

Kalavacharla, Venugopal

2016-01-01

We discovered variable modes of parental care in a breeding population of color-banded Veeries (Catharus fuscescens), a Nearctic-Neotropical migratory songbird, long thought to be socially monogamous, and performed a multi-locus DNA microsatellite analysis to estimate parentage and kinship in a sample of 37 adults and 21 offspring. We detected multiple mating in both sexes, and four modes of parental care that varied in frequency within and between years including multiple male feeders at some nests, and males attending multiple nests in the same season, each with a different female. Unlike other polygynandrous systems, genetic evidence indicates that multi-generational patterns of kinship occur among adult Veeries at our study site, and this was corroborated by the capture of an adult male in 2013 that had been banded as a nestling in 2011 at a nest attended by multiple male feeders. All genotyped adults (n = 37) were related to at least one other bird in the sample at the cousin level or greater (r ≥ 0.125), and 81% were related to at least one other bird at the half-sibling level or greater (r ≥ 0.25, range 0.25–0.60). Although our sample size is small, it appears that the kin structure is maintained by natal philopatry in both sexes, and that Veeries avoid mating with close genetic kin. At nests where all adult feeders were genotyped (n = 9), the male(s) were unrelated to the female (mean r = -0.11 ± 0.15), whereas genetic data suggest close kinship (r = 0.254) between two male co-feeders at the nests of two females in 2011, and among three of four females that were mated to the same polygynous male in 2012. To our knowledge, this is the first evidence of polygynandry occurring among multiple generations of close genetic kin on the breeding ground of a Nearctic-Neotropical migratory songbird. PMID:27331399

Effects of Home Energy Management Systems on Distribution Utilities and Feeders Under Various Market Structures: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruth, Mark; Pratt, Annabelle; Lunacek, Monte

2015-07-17

The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is poorly understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time of use tariff to estimate economic and physical impacts on both the households and the distribution utilities. HEMS reduce consumers’ electric bills by precooling housesmore » in the hours before peak electricity pricing. Household savings are greater than the reduction utility net revenue indicating that HEMS can provide a societal benefit providing tariffs are structured so that utilities remain solvent. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices and resulting in a higher peak load.« less

Real time testing of intelligent relays for synchronous distributed generation islanding detection

NASA Astrophysics Data System (ADS)

Zhuang, Davy

As electric power systems continue to grow to meet ever-increasing energy demand, their security, reliability, and sustainability requirements also become more stringent. The deployment of distributed energy resources (DER), including generation and storage, in conventional passive distribution feeders, gives rise to integration problems involving protection and unintentional islanding. Distributed generators need to be islanded for safety reasons when disconnected or isolated from the main feeder as distributed generator islanding may create hazards to utility and third-party personnel, and possibly damage the distribution system infrastructure, including the distributed generators. This thesis compares several key performance indicators of a newly developed intelligent islanding detection relay, against islanding detection devices currently used by the industry. The intelligent relay employs multivariable analysis and data mining methods to arrive at decision trees that contain both the protection handles and the settings. A test methodology is developed to assess the performance of these intelligent relays on a real time simulation environment using a generic model based on a real-life distribution feeder. The methodology demonstrates the applicability and potential advantages of the intelligent relay, by running a large number of tests, reflecting a multitude of system operating conditions. The testing indicates that the intelligent relay often outperforms frequency, voltage and rate of change of frequency relays currently used for islanding detection, while respecting the islanding detection time constraints imposed by standing distributed generator interconnection guidelines.

Distribution System Reliability Analysis for Smart Grid Applications

NASA Astrophysics Data System (ADS)

Aljohani, Tawfiq Masad

Reliability of power systems is a key aspect in modern power system planning, design, and operation. The ascendance of the smart grid concept has provided high hopes of developing an intelligent network that is capable of being a self-healing grid, offering the ability to overcome the interruption problems that face the utility and cost it tens of millions in repair and loss. To address its reliability concerns, the power utilities and interested parties have spent extensive amount of time and effort to analyze and study the reliability of the generation and transmission sectors of the power grid. Only recently has attention shifted to be focused on improving the reliability of the distribution network, the connection joint between the power providers and the consumers where most of the electricity problems occur. In this work, we will examine the effect of the smart grid applications in improving the reliability of the power distribution networks. The test system used in conducting this thesis is the IEEE 34 node test feeder, released in 2003 by the Distribution System Analysis Subcommittee of the IEEE Power Engineering Society. The objective is to analyze the feeder for the optimal placement of the automatic switching devices and quantify their proper installation based on the performance of the distribution system. The measures will be the changes in the reliability system indices including SAIDI, SAIFI, and EUE. The goal is to design and simulate the effect of the installation of the Distributed Generators (DGs) on the utility's distribution system and measure the potential improvement of its reliability. The software used in this work is DISREL, which is intelligent power distribution software that is developed by General Reliability Co.

Effects of feeder design and changing source of water to a location separate from the wet-dry feeder at 4 or 8 weeks before harvest on growth, feeding behavior, and carcass characteristics of finishing pigs.

PubMed

Bergstrom, J R; Nelssen, J L; Edwards, L N; Tokach, M D; Dritz, S S; Goodband, R D; DeRouchey, J M

2012-12-01

Our objectives were to compare a conventional dry (5-space, 152.4-cm-wide) and a wet-dry (double-sided, each side = 38.1-cm-wide single space) feeder and to determine if changing the source of water to a location separate from a wet-dry feeder would result in improved G:F and carcass characteristics. Water supply to the wet-dry feeder was shut off and the cup waterer was turned on in 8 pens at 8 (d 69) or 4 (d 97) wk prior to harvest. For the remaining 8 wet-dry feeder pens, the feeder provided the sole water source for the entire experiment. A total of 1,296 pigs (PIC, 337 × 1050; initially 19.4 kg BW) were used, with 27 pigs/pen (14 barrows and 13 gilts) and 24 pens/feeder design. From d 0 to 69, pigs fed with the wet-dry feeder had increased (P < 0.05) ADG, ADFI, G:F, and d 69 BW compared with those using the conventional dry feeder. Overall (d 0 to 124), pigs using fed with the water source in the wet-dry feeder the entire time had greater (P < 0.05) ADG, ADFI, final BW, and HCW the other treatments. The overall G:F was not different (P > 0.05) among pigs fed with the different feeder treatments. Pigs fed with the wet-dry feeder where water source was changed at 4 wk before harvest had greater (P < 0.05) ADG than pigs that used a conventional dry feeder. Pigs where the water source was changed at 4 wk had greater (P < 0.05) ADFI than those were the water source was changed 8 wk prior to harvest, and for pigs fed with the conventional dry feeder ADFI was intermediate. Back fat depth of pigs where the water source was changed at 8 wk before harvest was reduced (P < 0.05) compared with all other treatments and LM depth was greater (P < 0.05) than that of pigs using a conventional dry feeder and where the water source was changed at 4 week before harvest. Pigs fed using the wet-dry feeder visited the feeder less frequently (P < 0.05) and spent less total time at the feeder (P < 0.05) than those fed with the conventional dry feeder. The differences in feeding patterns remained even after the access to water was removed from the wet-dry feeder, with no change in the amount of aggressive behavior observed at the feeder. Pigs fed with a wet-dry feeder had an increased growth rate compared with those fed with a conventional dry feeder. Although measures of carcass leanness were improved by changing the location of the water, removing the water from the feeder also eliminated any net improvement in BW from using a wet-dry feeder.

On Distributed PV Hosting Capacity Estimation, Sensitivity Study, and Improvement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Fei; Mather, Barry

This paper first studies the estimated distributed PV hosting capacities of seventeen utility distribution feeders using the Monte Carlo simulation based stochastic analysis, and then analyzes the sensitivity of PV hosting capacity to both feeder and photovoltaic system characteristics. Furthermore, an active distribution network management approach is proposed to maximize PV hosting capacity by optimally switching capacitors, adjusting voltage regulator taps, managing controllable branch switches and controlling smart PV inverters. The approach is formulated as a mixed-integer nonlinear optimization problem and a genetic algorithm is developed to obtain the solution. Multiple simulation cases are studied and the effectiveness of themore » proposed approach on increasing PV hosting capacity is demonstrated.« less

Method, memory media and apparatus for detection of grid disconnect

DOEpatents

Ye, Zhihong [Clifton Park, NY; Du, Pengwei [Troy, NY

2008-09-23

A phase shift procedure for detecting a disconnect of a power grid from a feeder that is connected to a load and a distributed generator. The phase shift procedure compares a current phase shift of the output voltage of the distributed generator with a predetermined threshold and if greater, a command is issued for a disconnect of the distributed generator from the feeder. To extend the range of detection, the phase shift procedure is used when a power mismatch between the distributed generator and the load exceeds a threshold and either or both of an under/over frequency procedure and an under/over voltage procedure is used when any power mismatch does not exceed the threshold.

Distribution of lead and cadmium in trophic levels of some marine organisms.

PubMed

Mesmar, M

1987-01-01

The concentrations of lead and cadmium in two species of algae, two species of invertebrates, and one species of fish (from Fehmern Baltic Sea) were determined using atomic absorption spectrophotometry. The concentrations of these metals at the producer level (algae) were always higher than at the consumer level. Also, among the consumers there was an obvious difference according to feeding habits, in such a way that they could be ranked according to their high content of lead and cadmium as follows: filter feeder (detritous feeder), plankton feeder. In addition, distribution of lead and cadmium varied within the individual producer (Fucus vesiculosus) in such a way that the holdfast exhibited the highest concentration followed by the apcial tip and the branches of the first dichotomy was the lowest. This alga reflects clear selectivity in absorbing more lead than cadmium.

Large Scale Simulation Platform for NODES Validation Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sotorrio, P.; Qin, Y.; Min, L.

2017-04-27

This report summarizes the Large Scale (LS) simulation platform created for the Eaton NODES project. The simulation environment consists of both wholesale market simulator and distribution simulator and includes the CAISO wholesale market model and a PG&E footprint of 25-75 feeders to validate the scalability under a scenario of 33% RPS in California with additional 17% of DERS coming from distribution and customers. The simulator can generate hourly unit commitment, 5-minute economic dispatch, and 4-second AGC regulation signals. The simulator is also capable of simulating greater than 10k individual controllable devices. Simulated DERs include water heaters, EVs, residential and lightmore » commercial HVAC/buildings, and residential-level battery storage. Feeder-level voltage regulators and capacitor banks are also simulated for feeder-level real and reactive power management and Vol/Var control.« less

Optimal Capacitor Bank Capacity and Placement in Distribution Systems with High Distributed Solar Power Penetration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hodge, Brian S; Mather, Barry A; Cho, Gyu-Jung

Capacitor banks have been generally installed and utilized to support distribution voltage during period of higher load or on longer, higher impedance, feeders. Installations of distributed energy resources in distribution systems are rapidly increasing, and many of these generation resources have variable and uncertain power output. These generators can significantly change the voltage profile across a feeder, and therefore when a new capacitor bank is needed analysis of optimal capacity and location of the capacitor bank is required. In this paper, we model a particular distribution system including essential equipment. An optimization method is adopted to determine the best capacitymore » and location sets of the newly installed capacitor banks, in the presence of distributed solar power generation. Finally we analyze the optimal capacitor banks configuration through the optimization and simulation results.« less

Social and nonsocial behaviours of sex- and age-matched enclosed and free-ranging rhesus monkeys (Macaca mulatta).

PubMed

Baulu, J; Redmond, D E

1980-01-01

The behavioural profiles (time budgeting of social and nonsocial activities) and the frequencies of major social interactions of corral-enclosed rhesus monkeys were compared with sex- and age-matched free-ranging rhesus monkeys on La Cueva Island, Puerto Rico. All animals (n = 32) were provisioned ad libitum at specific feeder sites. The occurrence of 14 behaviours around feeders was compared with their occurrence away from the feeders by noting the location of each monkey relative to the feeder at the time of observation. An analysis of variance between free-ranging versus corral-enclosed groups and within groups by location (around or away from the feeder) revealed significant differences in several behavioural categories, including foraging, lookout, inactive, dominant, submissive, allogrooming, social contact, social initiative, active, and passive behaviours. When the effect of limited food distribution sites was analyzed by comparing data recorded away from the feeding sites, there were remarkably few differences between the groups.

Wildlife contact rates at artificial feeding sites in Texas.

PubMed

Campbell, Tyler A; Long, David B; Shriner, Susan A

2013-06-01

Given the popularity of feeding white-tailed deer (Odocoileus virginianus) in Texas and the increasing amount of corn that is distributed, more information is needed on the impacts of this activity on non-target wildlife. Our objectives were to report visitation, intra- and interspecific contact, and contact rates of wildlife at artificial feeding sites in Texas. Our study was conducted at three sites in Kleberg and Nueces counties, Texas. We trapped animals from February to April and August to September, 2009 and marked animals with passive integrated transponder (PIT) tags. At each site and season, we placed one feeder system containing a PIT tag reader within 600 m of trap locations. Readers detected PIT tags from a distance of 25 cm. We determined a contact event to occur when two different PIT tags were detected by feeder systems within 5 s. We recorded 62,719 passes by raccoons (Procyon lotor), 103,512 passes by collared peccaries (Pecari tajacu), 2,923 passes by feral swine (Sus scrofa), 1,336 passes by fox squirrels (Sciurus niger), and no passes by opossums (Didelphis virginiana) at feeder systems. For site-season combinations in which contact events occurred, we found intraspecific contact rates (contacts per day) for raccoons, collared peccaries, and feral swine to be 0.81-124.77, 0.69-38.08, and 0.0-0.66, respectively. Throughout our study we distributed ~2,625 kg of whole kernel corn, which resulted in 6,351 contact events between marked wildlife (2.4 contacts per kg of corn). If 136 million kg of corn is distributed in Texas annually, we would expect >5.2 billion unnatural contact events between wildlife would result from this activity each year in Texas. Consequently, we do not believe that it is wise for natural resource managers to maintain artificial feeding sites for white-tailed deer or other wildlife due to pathogen transmission risks.

Wildlife Contact Rates at Artificial Feeding Sites in Texas

NASA Astrophysics Data System (ADS)

Campbell, Tyler A.; Long, David B.; Shriner, Susan A.

2013-06-01

Given the popularity of feeding white-tailed deer ( Odocoileus virginianus) in Texas and the increasing amount of corn that is distributed, more information is needed on the impacts of this activity on non-target wildlife. Our objectives were to report visitation, intra- and interspecific contact, and contact rates of wildlife at artificial feeding sites in Texas. Our study was conducted at three sites in Kleberg and Nueces counties, Texas. We trapped animals from February to April and August to September, 2009 and marked animals with passive integrated transponder (PIT) tags. At each site and season, we placed one feeder system containing a PIT tag reader within 600 m of trap locations. Readers detected PIT tags from a distance of 25 cm. We determined a contact event to occur when two different PIT tags were detected by feeder systems within 5 s. We recorded 62,719 passes by raccoons ( Procyon lotor), 103,512 passes by collared peccaries ( Pecari tajacu), 2,923 passes by feral swine ( Sus scrofa), 1,336 passes by fox squirrels ( Sciurus niger), and no passes by opossums ( Didelphis virginiana) at feeder systems. For site-season combinations in which contact events occurred, we found intraspecific contact rates (contacts per day) for raccoons, collared peccaries, and feral swine to be 0.81-124.77, 0.69-38.08, and 0.0-0.66, respectively. Throughout our study we distributed ~2,625 kg of whole kernel corn, which resulted in 6,351 contact events between marked wildlife (2.4 contacts per kg of corn). If 136 million kg of corn is distributed in Texas annually, we would expect >5.2 billion unnatural contact events between wildlife would result from this activity each year in Texas. Consequently, we do not believe that it is wise for natural resource managers to maintain artificial feeding sites for white-tailed deer or other wildlife due to pathogen transmission risks.

Comparison of eight logger layouts for monitoring animal-level temperature and humidity during commercial feeder cattle transport.

PubMed

Goldhawk, C; Crowe, T; González, L A; Janzen, E; Kastelic, J; Pajor, E; Schwartzkopf-Genswein, K

2014-09-01

Measuring animal-level conditions during transit provides information regarding the true risk of environmental challenges to cattle welfare during transportation. However, due to constraints on placing loggers at the animal level, there is a need to identify appropriate proxy locations. The objective was to evaluate 8 distributions of ceiling-level loggers in the deck and belly compartments of pot-belly trailers for assessing animal-level temperature and humidity during 5 to 18 h commercial transportation of feeder cattle. Ambient conditions during transportation ranged from 3.6 to 45.2°C (20.3 ± 7.61°C, mean ± SD). When considering the entire journey, average differences between ceiling and animal-level temperatures were similar among logger layouts (P > 0.05). The uncertainty in the difference in temperature and humidity between locations was high relative to the magnitude of the difference between animal- and ceiling-level conditions. Single-logger layouts required larger adjustments to predict animal-level conditions within either compartment, during either the entire journey or when the trailer was stationary (P < 0.05). Within certain logger layouts, there were small but significant differences in the ability of regression equations to predict animal-level conditions that were associated with cattle weight and available space relative to body size. Furthermore, evaluation of logger layouts based solely on the entire journey without consideration of stationary periods did not adequately capture variability in layout performance. In conclusion, to adequately monitor animal-level temperature and humidity, 10 loggers distributed throughout the compartment was recommended over single-logger layouts within both the deck and belly compartments of pot-belly trailers transporting feeder cattle in warm weather.

Feed intake and behavior of dairy goats when offered an elevated feed bunk.

PubMed

Neave, Heather W; von Keyserlingk, Marina A G; Weary, Daniel M; Zobel, Gosia

2018-04-01

Goats are browsers and select vegetation at various heights when foraging. On commercial farms, dairy goats are typically fed from low-level feed bunks. The objective of this study was to determine how feed intake and feeding behavior vary when goats are offered feed at variable heights, with the potential of evaluating the benefits of offering an elevated feeder to dairy goats. Thirteen Saanen X dairy goats were housed in a home pen with a lying area of wood shavings, where they were pre-exposed for 24 d to 3 feeder heights designed to result in differences in head height while feeding: floor level (head lowered relative to body), head level (head level relative to body), and elevated level (head and neck angled upward). Nine groups of 3 goats each were randomly selected and housed for 24 h in a test pen identical to the home pen except that it contained 1 of each of the 3 feeder heights. Each feeder contained ad libitum chopped alfalfa silage and a top-dressed corn-based supplement, refreshed twice daily. Refusals from inside and under each feeder were weighed to calculate intake. Feed intake increased with increasing feeder height (mean ± SE; 0.18, 0.29, and 0.34 ± 0.04 kg of DM/goat for floor-level, head-level, and elevated-level feeders, respectively). Total feeding time did not vary with feeder height, but feeding rate tended to be faster at the elevated-level feeder (14.5 ± 2.1 g of DM/min) compared with head-level (9.2 ± 2.3 g of DM/min) and floor-level (8.9 ± 2.1 g of DM/min) feeders. Goats visited the floor-level feeder (36.4 ± 8.4 visits/goat) less than the head-level (79.4 ± 8.4 visits/goat) and elevated-level (74.8 ± 8.4 visits/goat) feeders. The number of displacements per minute of feeding time (physical removal of another goat from the feeding place) was greater at the elevated-level feeder (0.46 ± 0.06 displacements/min) compared with the floor-level feeder (0.23 ± 0.06 displacements/min) and tended to differ from the head-level feeder (0.27 ± 0.06 displacements/min). We conclude that goats eat more from an elevated feeder and compete more to access this feeder. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Development of a Dynamically Configurable, Object-Oriented Framework for Distributed, Multi-modal Computational Aerospace Systems Simulation

NASA Technical Reports Server (NTRS)

Afjeh, Abdollah A.; Reed, John A.

2003-01-01

The following reports are presented on this project:A first year progress report on: Development of a Dynamically Configurable,Object-Oriented Framework for Distributed, Multi-modal Computational Aerospace Systems Simulation; A second year progress report on: Development of a Dynamically Configurable, Object-Oriented Framework for Distributed, Multi-modal Computational Aerospace Systems Simulation; An Extensible, Interchangeable and Sharable Database Model for Improving Multidisciplinary Aircraft Design; Interactive, Secure Web-enabled Aircraft Engine Simulation Using XML Databinding Integration; and Improving the Aircraft Design Process Using Web-based Modeling and Simulation.

Multi-objective possibilistic model for portfolio selection with transaction cost

NASA Astrophysics Data System (ADS)

Jana, P.; Roy, T. K.; Mazumder, S. K.

2009-06-01

In this paper, we introduce the possibilistic mean value and variance of continuous distribution, rather than probability distributions. We propose a multi-objective Portfolio based model and added another entropy objective function to generate a well diversified asset portfolio within optimal asset allocation. For quantifying any potential return and risk, portfolio liquidity is taken into account and a multi-objective non-linear programming model for portfolio rebalancing with transaction cost is proposed. The models are illustrated with numerical examples.

A Review of Power Distribution Test Feeders in the United States and the Need for Synthetic Representative Networks

DOE Office of Scientific and Technical Information (OSTI.GOV)

Postigo Marcos, Fernando E.; Domingo, Carlos Mateo; San Roman, Tomas Gomez

Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available formore » testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. As a result, this both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.« less

A Review of Power Distribution Test Feeders in the United States and the Need for Synthetic Representative Networks

DOE PAGES

Postigo Marcos, Fernando E.; Domingo, Carlos Mateo; San Roman, Tomas Gomez; ...

2017-11-18

Under the increasing penetration of distributed energy resources and new smart network technologies, distribution utilities face new challenges and opportunities to ensure reliable operations, manage service quality, and reduce operational and investment costs. Simultaneously, the research community is developing algorithms for advanced controls and distribution automation that can help to address some of these challenges. However, there is a shortage of realistic test systems that are publically available for development, testing, and evaluation of such new algorithms. Concerns around revealing critical infrastructure details and customer privacy have severely limited the number of actual networks published and that are available formore » testing. In recent decades, several distribution test feeders and US-featured representative networks have been published, but the scale, complexity, and control data vary widely. This paper presents a first-of-a-kind structured literature review of published distribution test networks with a special emphasis on classifying their main characteristics and identifying the types of studies for which they have been used. As a result, this both aids researchers in choosing suitable test networks for their needs and highlights the opportunities and directions for further test system development. In particular, we highlight the need for building large-scale synthetic networks to overcome the identified drawbacks of current distribution test feeders.« less

Optimal Operation and Dispatch of Voltage Regulation Devices Considering High Penetrations of Distributed Photovoltaic Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mather, Barry A; Hodge, Brian S; Cho, Gyu-Jung

Voltage regulation devices have been traditionally installed and utilized to support distribution voltages. Installations of distributed energy resources (DERs) in distribution systems are rapidly increasing, and many of these generation resources have variable and uncertain power output. These generators can significantly change the voltage profile for a feeder; therefore, in the distribution system planning stage of the optimal operation and dispatch of voltage regulation devices, possible high penetrations of DERs should be considered. In this paper, we model the IEEE 34-bus test feeder, including all essential equipment. An optimization method is adopted to determine the optimal siting and operation ofmore » the voltage regulation devices in the presence of distributed solar power generation. Finally, we verify the optimal configuration of the entire system through the optimization and simulation results.« less

Effect of artificial feeders on pollen loads of the hummingbirds of Cerro de la Muerte, Costa Rica.

PubMed

Avalos, Gerardo; Soto, Alejandra; Alfaro, Willy

2012-03-01

Although sugar-water feeders are commonly used by enthusiasts to attract hummingbirds, little is known about how they affect hummingbird behavior and flower use. We studied the highland hummingbird assemblage of Cerro de La Muerte, Costa Rica, both at a site with permanent feeders (La Georgina Restaurant) and further from it. We examined how feeder use and monopolization affected seasonal changes in pollen loads during four sampling periods, including dry and wet seasons, from 2003-2005. We expected that species monopolizing the feeders would carry little or no pollen whatsoever, and would have pollen loads characterized by low floral diversity, in contrast with species less dependent on feeders. We obtained pollen samples from 183 individuals of four hummingbird species captured around the feeders using mist nets, which were compared with a pollen reference collection of plants with a pollination syndrome by hummingbirds. The same methods were implemented at a site 3km away from the feeders. Feeder usage was quantified by counting the number of times hummingbirds drank from the feeders in periods of 4min separated by 1min. The effects of hummingbird species and season on pollen load categories were assessed using a nominal logistic regression. The alpha species at the site, the Fiery-throated Hummingbird (Panterpe insignis), dominated the feeders during the dry season. Meanwhile, in the wet season, feeder usage was more evenly distributed across species, with the exception of the Volcano Hummingbird, Selasphorus flammula, which occupies the last place in the dominance hierarchy. Pollen loads of hummingbirds captured near feeders were low in abundance (more than 50% of captured individuals had zero or low pollen loads), and low in species richness (96% of the hummingbirds with pollen from only one plant genus, Centropogon). Overall pollen loads increased during the dry season coinciding with peaks in flower availability, although the majority of captured hummingbirds carried no pollen. Mist nets located 3km from La Georgina returned few captures (one-to-three specimens) per sampling date, contrasting with observations made before feeders were present. These results suggest that sugar-water feeders gather hummingbirds in over considerable distances drawing them away from flowers. The competitive and antagonistic pattern shown between feeders and flowers indicate that natural pollination system could be significantly altered. Supplementing hummingbirds with food seems likely to interfere with pollination networks already stressed by many anthropogenic effects.

Optimal Regulation of Virtual Power Plants

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dall Anese, Emiliano; Guggilam, Swaroop S.; Simonetto, Andrea

This paper develops a real-time algorithmic framework for aggregations of distributed energy resources (DERs) in distribution networks to provide regulation services in response to transmission-level requests. Leveraging online primal-dual-type methods for time-varying optimization problems and suitable linearizations of the nonlinear AC power-flow equations, we believe this work establishes the system-theoretic foundation to realize the vision of distribution-level virtual power plants. The optimization framework controls the output powers of dispatchable DERs such that, in aggregate, they respond to automatic-generation-control and/or regulation-services commands. This is achieved while concurrently regulating voltages within the feeder and maximizing customers' and utility's performance objectives. Convergence andmore » tracking capabilities are analytically established under suitable modeling assumptions. Simulations are provided to validate the proposed approach.« less

Urbanization affects neophilia and risk-taking at bird-feeders

NASA Astrophysics Data System (ADS)

Tryjanowski, Piotr; Møller, Anders Pape; Morelli, Federico; Biaduń, Waldemar; Brauze, Tomasz; Ciach, Michał; Czechowski, Paweł; Czyż, Stanisław; Dulisz, Beata; Goławski, Artur; Hetmański, Tomasz; Indykiewicz, Piotr; Mitrus, Cezary; Myczko, Łukasz; Nowakowski, Jacek J.; Polakowski, Michał; Takacs, Viktoria; Wysocki, Dariusz; Zduniak, Piotr

2016-06-01

Urban environments cover vast areas with a high density of humans and their dogs and cats causing problems for exploitation of new resources by wild animals. Such resources facilitate colonization by individuals with a high level of neophilia predicting that urban animals should show more neophilia than rural conspecifics. We provided bird-feeders across urban environments in 14 Polish cities and matched nearby rural habitats, testing whether the presence of a novel item (a brightly coloured green object made out of gum with a tuft of hair) differentially delayed arrival at feeders in rural compared to urban habitats. The presence of a novel object reduced the number of great tits Parus major, but also the total number of all species of birds although differentially so in urban compared to rural areas. That was the case independent of the potentially confounding effects of temperature, population density of birds, and the abundance of cats, dogs and pedestrians. The number of great tits and the total number of birds attending feeders increased in urban compared to rural areas independent of local population density of birds. This implies that urban birds have high levels of neophilia allowing them to readily exploit unpredictable resources in urban environments.

Relative Preference and Localized Food Affect Predator Space Use and Consumption of Incidental Prey

PubMed Central

Schartel, Tyler E.; Schauber, Eric M.

2016-01-01

Abundant, localized foods can concentrate predators and their foraging efforts, thus altering both the spatial distribution of predation risk and predator preferences for prey that are encountered incidentally. However, few investigations have quantified the spatial scale over which localized foods affect predator foraging behavior and consumption of incidental prey. In spring 2010, we experimentally tested how point-source foods altered how generalist predators (white-footed mice, Peromyscus leucopus) utilized space and depredated two incidental prey items: almonds (Prunus dulcis; highly profitable) and maple seeds (Acer saccharum; less profitable). We estimated mouse population densities with trapping webs, quantified mouse consumption rates of these incidental prey items, and measured local mouse activity with track plates. We predicted that 1) mouse activity would be elevated near full feeders, but depressed at intermediate distances from the feeder, 2) consumption of both incidental prey would be high near feeders providing less-preferred food and, 3) consumption of incidental prey would be contingent on predator preference for prey relative to feeders providing more-preferred food. Mouse densities increased significantly from pre- to post-experiment. Mean mouse activity was unexpectedly greatest in control treatments, particularly <15 m from the control (empty) feeder. Feeders with highly preferred food (sunflower seeds) created localized refuges for incidental prey at intermediate distances (15 to 25m) from the feeder. Feeders with less-preferred food (corn) generated localized high risk for highly preferred almonds <10 m of the feeder. Our findings highlight the contingent but predictable effects of locally abundant food on risk experienced by incidental prey, which can be positive or negative depending on both spatial proximity and relative preference. PMID:26978659

Relative Preference and Localized Food Affect Predator Space Use and Consumption of Incidental Prey.

PubMed

Schartel, Tyler E; Schauber, Eric M

2016-01-01

Abundant, localized foods can concentrate predators and their foraging efforts, thus altering both the spatial distribution of predation risk and predator preferences for prey that are encountered incidentally. However, few investigations have quantified the spatial scale over which localized foods affect predator foraging behavior and consumption of incidental prey. In spring 2010, we experimentally tested how point-source foods altered how generalist predators (white-footed mice, Peromyscus leucopus) utilized space and depredated two incidental prey items: almonds (Prunus dulcis; highly profitable) and maple seeds (Acer saccharum; less profitable). We estimated mouse population densities with trapping webs, quantified mouse consumption rates of these incidental prey items, and measured local mouse activity with track plates. We predicted that 1) mouse activity would be elevated near full feeders, but depressed at intermediate distances from the feeder, 2) consumption of both incidental prey would be high near feeders providing less-preferred food and, 3) consumption of incidental prey would be contingent on predator preference for prey relative to feeders providing more-preferred food. Mouse densities increased significantly from pre- to post-experiment. Mean mouse activity was unexpectedly greatest in control treatments, particularly <15 m from the control (empty) feeder. Feeders with highly preferred food (sunflower seeds) created localized refuges for incidental prey at intermediate distances (15 to 25m) from the feeder. Feeders with less-preferred food (corn) generated localized high risk for highly preferred almonds <10 m of the feeder. Our findings highlight the contingent but predictable effects of locally abundant food on risk experienced by incidental prey, which can be positive or negative depending on both spatial proximity and relative preference.

14 CFR 29.1355 - Distribution system.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Distribution system. 29.1355 Section 29... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Equipment Electrical Systems and Equipment § 29.1355 Distribution system. (a) The distribution system includes the distribution busses, their associated feeders...

14 CFR 25.1355 - Distribution system.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Distribution system. 25.1355 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Equipment Electrical Systems and Equipment § 25.1355 Distribution system. (a) The distribution system includes the distribution busses, their associated feeders...

Feeders of Free-Roaming Cats: Personal Characteristics, Feeding Practices, and Data on Cat Health and Welfare in an Urban Setting of Israel.

PubMed

Gunther, Idit; Raz, Tal; Even Zor, Yehonatan; Bachowski, Yuval; Klement, Eyal

2016-01-01

Cat feeders serve as an important source of available food for free-roaming cats (FRCs) and can play a central role in providing data on FRC distribution, welfare, and health. Data on cat feeder personalities as well as a better understanding of their feeding practices offer relevance for decision making concerning FRC population control strategies. The current study surveyed 222 FRC feeders who responded to a municipal trap-neuter-return (TNR) campaign in an Israeli central urban setting. The aim of the study was to describe their personal characteristics, feeding practices, and the FRC populations they feed. Feeders were divided into four groups according to the number of cats they claimed to feed per day (group 1: fed up to 5 cats, group 2: fed 6-10 cats, group 3: fed 11-20 cats, and group 4: fed ≥21 cats). Most feeders were women (81%), with a median age of 58 years (range 18-81). The feeders reported an overall feeding of 3337 cats in 342 different feeding locations. Feeders of group 4 comprised 15.31% (n = 34) of all feeders but fed 56% (n = 1869) of the FRC in 37.42% (n = 128) of the feeding locations. "Heavy" feeders (groups 3 and 4) reported that they traveled significantly longer distances in order to feed the cats. Commercial dry food consisted of 90% of the food they provided, with 66% of them feeding once a day, with less food per cat per day than the other feeder groups. Interestingly, "heavy" feeders were usually singles, had on average fewer siblings, a clear preference for owning cats as pets, and lived in lower income neighborhoods. According to the feeders' reports on the FRC populations they fed, 69.7% (2325/3337) cats were neutered and 11.8% (395/3337) were kittens. In addition, they reported that 1.6% (54/3337) of the cats were limping, 2% (67/3337) suffered from a systemic disease, 4% (135/3337) had skin lesions, and 3.9% (130/3337) were suffering from a chronic disability. Abundance of kittens and morbidity rate were significantly and negatively associated with neutering rate. These findings are in accordance with the suggestion that neutering may potentially improve cat welfare by reducing morbidity. Collaboration by the authorities with these heavy feeders, who represent a small number of FRC feeders and feed substantial FRC numbers, may be significant for the control and monitoring of FRC populations and their resources.

Flexible responses to visual and olfactory stimuli by foraging Manduca sexta: larval nutrition affects adult behaviour.

PubMed

Goyret, Joaquín; Kelber, Almut; Pfaff, Michael; Raguso, Robert A

2009-08-07

Here, we show that the consequences of deficient micronutrient (beta-carotene) intake during larval stages of Manduca sexta are carried across metamorphosis, affecting adult behaviour. Our manipulation of larval diet allowed us to examine how developmental plasticity impacts the interplay between visual and olfactory inputs on adult foraging behaviour. Larvae of M. sexta were reared on natural (Nicotiana tabacum) and artificial laboratory diets containing different concentrations of beta-carotene (standard diet, low beta-carotene, high beta-carotene and cornmeal). This vitamin-A precursor has been shown to be crucial for photoreception sensitivity in the retina of M. sexta. After completing development, post-metamorphosis, starved adults were presented with artificial feeders that could be either scented or unscented. Regardless of their larval diet, adult moths fed with relatively high probabilities on scented feeders. When feeders were unscented, moths reared on tobacco were more responsive than moths reared on beta-carotene-deficient artificial diets. Strikingly, moths reared on artificial diets supplemented with increasing amounts of beta-carotene (low beta and high beta) showed increasing probabilities of response to scentless feeders. We discuss these results in relationship to the use of complex, multi-modal sensory information by foraging animals.

Flexible responses to visual and olfactory stimuli by foraging Manduca sexta: larval nutrition affects adult behaviour

PubMed Central

Goyret, Joaquín; Kelber, Almut; Pfaff, Michael; Raguso, Robert A.

2009-01-01

Here, we show that the consequences of deficient micronutrient (β-carotene) intake during larval stages of Manduca sexta are carried across metamorphosis, affecting adult behaviour. Our manipulation of larval diet allowed us to examine how developmental plasticity impacts the interplay between visual and olfactory inputs on adult foraging behaviour. Larvae of M. sexta were reared on natural (Nicotiana tabacum) and artificial laboratory diets containing different concentrations of β-carotene (standard diet, low β-carotene, high β-carotene and cornmeal). This vitamin-A precursor has been shown to be crucial for photoreception sensitivity in the retina of M. sexta. After completing development, post-metamorphosis, starved adults were presented with artificial feeders that could be either scented or unscented. Regardless of their larval diet, adult moths fed with relatively high probabilities on scented feeders. When feeders were unscented, moths reared on tobacco were more responsive than moths reared on β-carotene-deficient artificial diets. Strikingly, moths reared on artificial diets supplemented with increasing amounts of β-carotene (low β and high β) showed increasing probabilities of response to scentless feeders. We discuss these results in relationship to the use of complex, multi-modal sensory information by foraging animals. PMID:19419987

Extremum Seeking Control of Smart Inverters for VAR Compensation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Arnold, Daniel; Negrete-Pincetic, Matias; Stewart, Emma

2015-09-04

Reactive power compensation is used by utilities to ensure customer voltages are within pre-defined tolerances and reduce system resistive losses. While much attention has been paid to model-based control algorithms for reactive power support and Volt Var Optimization (VVO), these strategies typically require relatively large communications capabilities and accurate models. In this work, a non-model-based control strategy for smart inverters is considered for VAR compensation. An Extremum Seeking control algorithm is applied to modulate the reactive power output of inverters based on real power information from the feeder substation, without an explicit feeder model. Simulation results using utility demand informationmore » confirm the ability of the control algorithm to inject VARs to minimize feeder head real power consumption. In addition, we show that the algorithm is capable of improving feeder voltage profiles and reducing reactive power supplied by the distribution substation.« less

Distribution system model calibration with big data from AMI and PV inverters

DOE PAGES

Peppanen, Jouni; Reno, Matthew J.; Broderick, Robert J.; ...

2016-03-03

Efficient management and coordination of distributed energy resources with advanced automation schemes requires accurate distribution system modeling and monitoring. Big data from smart meters and photovoltaic (PV) micro-inverters can be leveraged to calibrate existing utility models. This paper presents computationally efficient distribution system parameter estimation algorithms to improve the accuracy of existing utility feeder radial secondary circuit model parameters. The method is demonstrated using a real utility feeder model with advanced metering infrastructure (AMI) and PV micro-inverters, along with alternative parameter estimation approaches that can be used to improve secondary circuit models when limited measurement data is available. Lastly, themore » parameter estimation accuracy is demonstrated for both a three-phase test circuit with typical secondary circuit topologies and single-phase secondary circuits in a real mixed-phase test system.« less

Distribution system model calibration with big data from AMI and PV inverters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Peppanen, Jouni; Reno, Matthew J.; Broderick, Robert J.

Efficient management and coordination of distributed energy resources with advanced automation schemes requires accurate distribution system modeling and monitoring. Big data from smart meters and photovoltaic (PV) micro-inverters can be leveraged to calibrate existing utility models. This paper presents computationally efficient distribution system parameter estimation algorithms to improve the accuracy of existing utility feeder radial secondary circuit model parameters. The method is demonstrated using a real utility feeder model with advanced metering infrastructure (AMI) and PV micro-inverters, along with alternative parameter estimation approaches that can be used to improve secondary circuit models when limited measurement data is available. Lastly, themore » parameter estimation accuracy is demonstrated for both a three-phase test circuit with typical secondary circuit topologies and single-phase secondary circuits in a real mixed-phase test system.« less

RF model of the distribution system as a communication channel, phase 2. Volume 1: Summary Report

NASA Technical Reports Server (NTRS)

Rustay, R. C.; Gajjar, J. T.; Rankin, R. W.; Wentz, R. C.; Wooding, R.

1982-01-01

The design, implementation, and verification of a computerized model for predicting the steady-state sinusoidal response of radial (tree) configured distribution feeders was undertaken. That work demonstrated the feasibility and validity based on verification measurements made on a limited size portion of an actual live feeder. On that basis a follow-on effort concerned with (1) extending the verification based on a greater variety of situations and network size, (2) extending the model capabilities for reverse direction propagation, (3) investigating parameter sensitivities, (4) improving transformer models, and (5) investigating procedures/fixes for ameliorating propagation trouble spots was conducted. Results are summarized.

Determining the Impact of Steady-State PV Fault Current Injections on Distribution Protection

DOE Office of Scientific and Technical Information (OSTI.GOV)

Seuss, John; Reno, Matthew J.; Broderick, Robert Joseph

This report investigates the fault current contribution from a single large PV system and the impact it has on existing distribution overcurrent protection devices. Assumptions are made about the modeling of the PV system under fault to perform exhaustive steady - state fault analyses throughout distribution feeder models. Each PV interconnection location is tested to determine how the size of the PV system affects the fault current measured by each protection device. This data is then searched for logical conditions that indicate whether a protection device has operated in a manner that will cause more customer outages due to themore » addition of the PV system. This is referred to as a protection issue , and there are four unique types of issues that have been identified in the study. The PV system size at which any issues occur are recorded to determine the feeder's PV hosting capacity limitations due to interference with protection settings. The analysis is carried out on six feeder models. The report concludes with a discussion of the prevalence and cause of each protection issue caused by PV system fault current.« less

Winter range expansion of a hummingbird is associated with urbanization and supplementary feeding

PubMed Central

Wood, Eric M.

2017-01-01

Anthropogenic changes to the landscape and climate cause novel ecological and evolutionary pressures, leading to potentially dramatic changes in the distribution of biodiversity. Warm winter temperatures can shift species' distributions to regions that were previously uninhabitable. Further, urbanization and supplementary feeding may facilitate range expansions and potentially reduce migration tendency. Here we explore how these factors interact to cause non-uniform effects across a species's range. Using 17 years of data from the citizen science programme Project FeederWatch, we examined the relationships between urbanization, winter temperatures and the availability of supplementary food (i.e. artificial nectar) on the winter range expansion (more than 700 km northward in the past two decades) of Anna's hummingbirds (Calypte anna). We found that Anna's hummingbirds have colonized colder locations over time, were more likely to colonize sites with higher housing density and were more likely to visit feeders in the expanded range compared to the historical range. Additionally, their range expansion mirrored a corresponding increase over time in the tendency of people to provide nectar feeders in the expanded range. This work illustrates how humans may alter the distribution and potentially the migratory behaviour of species through landscape and resource modification. PMID:28381617

A Bayesian alternative for multi-objective ecohydrological model specification

NASA Astrophysics Data System (ADS)

Tang, Yating; Marshall, Lucy; Sharma, Ashish; Ajami, Hoori

2018-01-01

Recent studies have identified the importance of vegetation processes in terrestrial hydrologic systems. Process-based ecohydrological models combine hydrological, physical, biochemical and ecological processes of the catchments, and as such are generally more complex and parametric than conceptual hydrological models. Thus, appropriate calibration objectives and model uncertainty analysis are essential for ecohydrological modeling. In recent years, Bayesian inference has become one of the most popular tools for quantifying the uncertainties in hydrological modeling with the development of Markov chain Monte Carlo (MCMC) techniques. The Bayesian approach offers an appealing alternative to traditional multi-objective hydrologic model calibrations by defining proper prior distributions that can be considered analogous to the ad-hoc weighting often prescribed in multi-objective calibration. Our study aims to develop appropriate prior distributions and likelihood functions that minimize the model uncertainties and bias within a Bayesian ecohydrological modeling framework based on a traditional Pareto-based model calibration technique. In our study, a Pareto-based multi-objective optimization and a formal Bayesian framework are implemented in a conceptual ecohydrological model that combines a hydrological model (HYMOD) and a modified Bucket Grassland Model (BGM). Simulations focused on one objective (streamflow/LAI) and multiple objectives (streamflow and LAI) with different emphasis defined via the prior distribution of the model error parameters. Results show more reliable outputs for both predicted streamflow and LAI using Bayesian multi-objective calibration with specified prior distributions for error parameters based on results from the Pareto front in the ecohydrological modeling. The methodology implemented here provides insight into the usefulness of multiobjective Bayesian calibration for ecohydrologic systems and the importance of appropriate prior distributions in such approaches.

A Bayesian Alternative for Multi-objective Ecohydrological Model Specification

NASA Astrophysics Data System (ADS)

Tang, Y.; Marshall, L. A.; Sharma, A.; Ajami, H.

2015-12-01

Process-based ecohydrological models combine the study of hydrological, physical, biogeochemical and ecological processes of the catchments, which are usually more complex and parametric than conceptual hydrological models. Thus, appropriate calibration objectives and model uncertainty analysis are essential for ecohydrological modeling. In recent years, Bayesian inference has become one of the most popular tools for quantifying the uncertainties in hydrological modeling with the development of Markov Chain Monte Carlo (MCMC) techniques. Our study aims to develop appropriate prior distributions and likelihood functions that minimize the model uncertainties and bias within a Bayesian ecohydrological framework. In our study, a formal Bayesian approach is implemented in an ecohydrological model which combines a hydrological model (HyMOD) and a dynamic vegetation model (DVM). Simulations focused on one objective likelihood (Streamflow/LAI) and multi-objective likelihoods (Streamflow and LAI) with different weights are compared. Uniform, weakly informative and strongly informative prior distributions are used in different simulations. The Kullback-leibler divergence (KLD) is used to measure the dis(similarity) between different priors and corresponding posterior distributions to examine the parameter sensitivity. Results show that different prior distributions can strongly influence posterior distributions for parameters, especially when the available data is limited or parameters are insensitive to the available data. We demonstrate differences in optimized parameters and uncertainty limits in different cases based on multi-objective likelihoods vs. single objective likelihoods. We also demonstrate the importance of appropriately defining the weights of objectives in multi-objective calibration according to different data types.

Method of feeding particulate material to a fluidized bed

DOEpatents

Borio, Richard W.; Goodstine, Stephen L.

1984-01-01

A centrifugal spreader type feeder that supplies a mixture of particulate limestone and coal to the top of a fluidized bed reactor having a flow of air upward therethrough. Large particles of particulate matter are distributed over the upper surface of the bed to utilize the natural mixing within the bed, while fine particles are adapted to utilize an independent feeder that separates them from the large particles and injects them into the bed.

46 CFR 111.97-7 - Distribution.

Code of Federal Regulations, 2012 CFR

2012-10-01

... REQUIREMENTS Electric Power-Operated Watertight Door Systems § 111.97-7 Distribution. (a) Each distribution... locking. (b) Each feeder supplying a watertight door operating system must be above the uppermost continuous deck. (c) Each watertight door operating system must have a separate branch circuit. ...

46 CFR 111.97-7 - Distribution.

Code of Federal Regulations, 2011 CFR

2011-10-01

... REQUIREMENTS Electric Power-Operated Watertight Door Systems § 111.97-7 Distribution. (a) Each distribution... locking. (b) Each feeder supplying a watertight door operating system must be above the uppermost continuous deck. (c) Each watertight door operating system must have a separate branch circuit. ...

46 CFR 111.97-7 - Distribution.

Code of Federal Regulations, 2010 CFR

2010-10-01

... REQUIREMENTS Electric Power-Operated Watertight Door Systems § 111.97-7 Distribution. (a) Each distribution... locking. (b) Each feeder supplying a watertight door operating system must be above the uppermost continuous deck. (c) Each watertight door operating system must have a separate branch circuit. ...

46 CFR 111.97-7 - Distribution.

Code of Federal Regulations, 2014 CFR

2014-10-01

... REQUIREMENTS Electric Power-Operated Watertight Door Systems § 111.97-7 Distribution. (a) Each distribution... locking. (b) Each feeder supplying a watertight door operating system must be above the uppermost continuous deck. (c) Each watertight door operating system must have a separate branch circuit. ...

46 CFR 111.97-7 - Distribution.

Code of Federal Regulations, 2013 CFR

2013-10-01

... REQUIREMENTS Electric Power-Operated Watertight Door Systems § 111.97-7 Distribution. (a) Each distribution... locking. (b) Each feeder supplying a watertight door operating system must be above the uppermost continuous deck. (c) Each watertight door operating system must have a separate branch circuit. ...

The effect of space allowance and cage size on laying hens housed in furnished cages, Part II: Behavior at the feeder.

PubMed

Widowski, T M; Caston, L J; Casey-Trott, T M; Hunniford, M E

2017-09-01

Standards for feeder (a.k.a. feed trough) space allowance (SA) are based primarily on studies in conventional cages where laying hens tend to eat simultaneously, limiting feeder space. Large furnished cages (FC) offer more total space and opportunities to perform a greater variety of behaviors, which may affect feeding behavior and feeder space requirements. Our objective was to determine the effects of floor/feeder SA on behavior at the feeder. LSL-Lite hens were housed in FC equipped with a nest, perches, and a scratch mat. Hens with SA of either 520 cm2 (Low; 8.9 cm feeder space/hen) or 748 cm2 (High; 12.8 cm feeder space/hen) per bird resulted in groups of 40 vs. 28 birds in small FC (SFC) and 80 vs. 55 in large FC (LFC). Chain feeders ran at 0500, 0800, 1100, 1400, and 1700 with lights on at 0500 and off at 1900 hours. Digital recordings of FC were scanned at chain feeder onset and every 15 min for one h after (5 scans × 5 feeding times × 2 d) to count the number of birds with their head in the feeder. All occurrences of aggressive pecks and displacements during 2 continuous 30-minute observations at 0800 h and 1700 h also were counted. Mixed model repeated analyses tested the effects of SA, cage size, and time on the percent of hens feeding, and the frequency of aggressive pecks and displacements. Surprisingly, the percent of birds feeding simultaneously was similar regardless of cage size (LFC: 23.0 ± 0.9%; SFC: 24.0 ± 1.0%; P = 0.44) or SA (Low: 23.8 ± 0.9%; High: 23.3 ± 1.0%; P = 0.62). More birds were observed feeding at 1700 h (35.3 ± 0.1%) than any at other time (P < 0.001). Feeder use differed by cage area (nest, middle, or scratch) over the d (P < 0.001). The frequency of aggressive pecks was low overall and not affected by SA or cage size. Frequency of displacements was also low but greater at Low SA (P = 0.001). There was little evidence of feeder competition at the Low SA in this study. © The Author 2017. Published by Oxford University Press on behalf of Poultry Science Association.

RF model of the distribution system as a communication channel, phase 2. Volume 3: Appendices

NASA Technical Reports Server (NTRS)

Rustay, R. C.; Gajjar, J. T.; Rankin, R. W.; Wentz, R. C.; Wooding, R.

1982-01-01

Program documentation concerning the design, implementation, and verification of a computerized model for predicting the steady-state sinusoidal response of radial configured distribution feeders is presented in these appendices.

Hawaiian Electric Advanced Inverter Grid Support Function Laboratory Validation and Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, Austin; Nagarajan, Adarsh; Prabakar, Kumar

The objective for this test plan was to better understand how to utilize the performance capabilities of advanced inverter functions to allow the interconnection of distributed energy resource (DER) systems to support the new Customer Self-Supply, Customer Grid-Supply, and other future DER programs. The purpose of this project was: 1) to characterize how the tested grid supportive inverters performed the functions of interest, 2) to evaluate the grid supportive inverters in an environment that emulates the dynamics of O'ahu's electrical distribution system, and 3) to gain insight into the benefits of the grid support functions on selected O'ahu island distributionmore » feeders. These goals were achieved through laboratory testing of photovoltaic inverters, including power hardware-in-the-loop testing.« less

Voltage Based Detection Method for High Impedance Fault in a Distribution System

NASA Astrophysics Data System (ADS)

Thomas, Mini Shaji; Bhaskar, Namrata; Prakash, Anupama

2016-09-01

High-impedance faults (HIFs) on distribution feeders cannot be detected by conventional protection schemes, as HIFs are characterized by their low fault current level and waveform distortion due to the nonlinearity of the ground return path. This paper proposes a method to identify the HIFs in distribution system and isolate the faulty section, to reduce downtime. This method is based on voltage measurements along the distribution feeder and utilizes the sequence components of the voltages. Three models of high impedance faults have been considered and source side and load side breaking of the conductor have been studied in this work to capture a wide range of scenarios. The effect of neutral grounding of the source side transformer is also accounted in this study. The results show that the algorithm detects the HIFs accurately and rapidly. Thus, the faulty section can be isolated and service can be restored to the rest of the consumers.

Examining System-Wide Impacts of Solar PV Control Systems with a Power Hardware-in-the-Loop Platform

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Tess L.; Fuller, Jason C.; Schneider, Kevin P.

2014-06-08

High penetration levels of distributed solar PV power generation can lead to adverse power quality impacts, such as excessive voltage rise, voltage flicker, and reactive power values that result in unacceptable voltage levels. Advanced inverter control schemes have been developed that have the potential to mitigate many power quality concerns. However, local closed-loop control may lead to unintended behavior in deployed systems as complex interactions can occur between numerous operating devices. To enable the study of the performance of advanced control schemes in a detailed distribution system environment, a test platform has been developed that integrates Power Hardware-in-the-Loop (PHIL) withmore » concurrent time-series electric distribution system simulation. In the test platform, GridLAB-D, a distribution system simulation tool, runs a detailed simulation of a distribution feeder in real-time mode at the Pacific Northwest National Laboratory (PNNL) and supplies power system parameters at a point of common coupling. At the National Renewable Energy Laboratory (NREL), a hardware inverter interacts with grid and PV simulators emulating an operational distribution system. Power output from the inverters is measured and sent to PNNL to update the real-time distribution system simulation. The platform is described and initial test cases are presented. The platform is used to study the system-wide impacts and the interactions of inverter control modes—constant power factor and active Volt/VAr control—when integrated into a simulated IEEE 8500-node test feeder. We demonstrate that this platform is well-suited to the study of advanced inverter controls and their impacts on the power quality of a distribution feeder. Additionally, results are used to validate GridLAB-D simulations of advanced inverter controls.« less

Self-adaptive multi-objective harmony search for optimal design of water distribution networks

NASA Astrophysics Data System (ADS)

Choi, Young Hwan; Lee, Ho Min; Yoo, Do Guen; Kim, Joong Hoon

2017-11-01

In multi-objective optimization computing, it is important to assign suitable parameters to each optimization problem to obtain better solutions. In this study, a self-adaptive multi-objective harmony search (SaMOHS) algorithm is developed to apply the parameter-setting-free technique, which is an example of a self-adaptive methodology. The SaMOHS algorithm attempts to remove some of the inconvenience from parameter setting and selects the most adaptive parameters during the iterative solution search process. To verify the proposed algorithm, an optimal least cost water distribution network design problem is applied to three different target networks. The results are compared with other well-known algorithms such as multi-objective harmony search and the non-dominated sorting genetic algorithm-II. The efficiency of the proposed algorithm is quantified by suitable performance indices. The results indicate that SaMOHS can be efficiently applied to the search for Pareto-optimal solutions in a multi-objective solution space.

The Varied Impacts of Energy Storage and Photovoltaics on Fossil Fuel Emissions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Studarus, Karen E.; Thayer, Brandon L.; Barrett, Emily L.

The emissions consequences of smart grid technologies can be significant but are not always intuitive. This is particularly true in the implementation of energy storage (ES) to enable the installation of solar photovoltaic (PV) systems. Using the web calculator at https://eqt.pnnl.gov and prototypical distribution feeders, this paper explores the COmore » $${_2}$$, SO$${_2}$$ and NO$${_x}$$ impacts of ES deployed with solar PV, where the energy storage system is operated to minimize load variation. Five regions of the country were explored using 15 prototypical distribution feeders and 2015 historical data. Impacts vary in direction, magnitude, and trend, and require a context-dependent screening method for faithful representation.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sumner, Dennis; Vosburg, Tom; Brunner, Steve

This project titled “Research, Development and Demonstration of Peak Load Reduction on Distribution Feeders Using Distributed Energy Resources for the City of Fort Collins” evolved in response to the Department of Energy’s (DOE) Funding Opportunity Announcement (FOA) Number DE-PS26-07NT43119. Also referred to as the Fort Collins Renewable and Distributed System Integration (RDSI) Project, the effort was undertaken by a diverse group of local government, higher education and business organizations; and was driven by three overarching goals: I. Fulfill the requirements of the DOE FOA’s Area of Interest 2: Renewable and Distributed System Integration; most notably, to demonstrate the ability tomore » reduce electric system distribution feeder peak load by 15% or more through the coordinated use of Distributed Energy Resources (DER). II. Advance the expertise, technologies and infrastructure necessary to support the long term vision of the Fort Collins Zero Energy District (FortZED) and move towards creating a zero energy district in the Fort Collins “Old Town” area. III. Further the goals of the City of Fort Collins Energy Policy, including the development of a Smart Grid-enabled distribution system in Fort Collins, expanded use of renewable energy, increased energy conservation, and peak load reduction. Through the collaborative efforts of the partner organizations, the Fort Collins RDSI project was successful in achieving all three of these goals. This report is organized into two distinct sections corresponding to the two phases of the project: • Part 1: Feeder Peak Load Reduction and the FortZED Initiative. • Part 2: Forming and Operating Utility Microgrids and Managing Load and Production Variability The original project scope addressed the Part 1 feeder peak load reduction. That work took place from 2009 through 2011 and was largely complete when the project scope was amended to include a demonstration of microgrid operations. While leveraging the assets, partner relationships, and lessons learned from Part 1, Part 2 was managed and executed as a distinct and substantially independent sub-project during the spring and summer of 2013. Both Parts 1 and 2 of the overall RDSI project can be viewed as cohesive stand-alone bodies of work and are presented as such within this report. In addition to the narratives, this document includes two Appendices that were compiled to supplement information about the various aspects of activities performed during Parts 1 and 2 of the project. Moreover, these Appendices are organized (as outlined below) so as to directly relate to the narratives in Part 1 and 2 of this report. • Appendix - Part 1: describes the roles of each project participant in regards to the feeder peak load reduction effort, and • Appendix - Part 2: deals with the microgrid research/demonstration.« less

Photovoltaic Hosting Capacity of Feeders with Reactive Power Control and Tap Changers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ceylan, Oğuzhan; Paudyal, Sumit; Bhattarai, Bishnu P.

This paper proposes an algorithm to determine photovoltaic (PV) hosting capacity of power distribution networks as a function of number of PV injection nodes, reactive power support from the PVs, and the sub-station load tap changers (LTCs). In the proposed method, several minute by minute simulations are run based on randomly chosen PV injection nodes, daily PV output profiles, and daily load profiles from a pool of high-resolution realistic data set. The simulation setup is built using OpenDSS and MATLAB. The performance of the proposed method is investigated in the IEEE 123-node distribution feeder for multiple scenarios. The case studiesmore » are performed particularly for one, two, five and ten PV injection nodes, and looking at the maximum voltage deviations. Case studies show that the PV hosting capacity of the 123-node feeder greatly differs with the number of PV injection nodes. We have also observed that the PV hosting capacity increases with reactive power support and higher tap position of sub-station LTC.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ruth, M.; Pratt, A.; Lunacek, M.

The combination of distributed energy resources (DER) and retail tariff structures to provide benefits to both utility consumers and the utilities is not well understood. To improve understanding, an Integrated Energy System Model (IESM) is being developed to simulate the physical and economic aspects of DER technologies, the buildings where they reside, and feeders servicing them. The IESM was used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electricmore » bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load. used to simulate 20 houses with home energy management systems on a single feeder under a time-of-use (TOU) tariff to estimate economic and physical impacts on both the households and the distribution utilities. Home energy management systems (HEMS) reduce consumers’ electric bills by precooling houses in the hours before peak electricity pricing. Utilization of HEMS reduce peak loads during high price hours but shifts it to hours with off-peak and shoulder prices, resulting in a higher peak load.« less

On the Improvement of Convergence Performance for Integrated Design of Wind Turbine Blade Using a Vector Dominating Multi-objective Evolution Algorithm

NASA Astrophysics Data System (ADS)

Wang, L.; Wang, T. G.; Wu, J. H.; Cheng, G. P.

2016-09-01

A novel multi-objective optimization algorithm incorporating evolution strategies and vector mechanisms, referred as VD-MOEA, is proposed and applied in aerodynamic- structural integrated design of wind turbine blade. In the algorithm, a set of uniformly distributed vectors is constructed to guide population in moving forward to the Pareto front rapidly and maintain population diversity with high efficiency. For example, two- and three- objective designs of 1.5MW wind turbine blade are subsequently carried out for the optimization objectives of maximum annual energy production, minimum blade mass, and minimum extreme root thrust. The results show that the Pareto optimal solutions can be obtained in one single simulation run and uniformly distributed in the objective space, maximally maintaining the population diversity. In comparison to conventional evolution algorithms, VD-MOEA displays dramatic improvement of algorithm performance in both convergence and diversity preservation for handling complex problems of multi-variables, multi-objectives and multi-constraints. This provides a reliable high-performance optimization approach for the aerodynamic-structural integrated design of wind turbine blade.

Comparing the 2000 and 2005 factors affecting the selling price of feeder cattle sold at Arkansas livestock auctions.

PubMed

Troxel, T R; Barham, B L

2007-12-01

The objectives of the study were to determine how factors affecting the selling price of feeder calves changed from 2000 to 2005 and to examine the perception that discounts narrow or even disappear as calf supplies decrease and selling prices increase. Data from weekly Arkansas livestock auctions were collected from January 1 to December 31 in 2000 and 2005. Data included calf sex, breed type, color, muscle score, horn status, frame score, fill, condition, health, and BW. Mean selling prices for 2000 and 2005 were $92.91 +/- 15.05 and $118.32 +/- 15.13 (mean +/- SD; $/45.45 kg), respectively. Individual price observations were subtracted from the respective annual means and became the dependent variable. The selling prices for feeder calves sold in groups of 2 to 5 calves and in groups of >/= 6 calves were greater in 2005 than 2000 (P < 0.001). Steers received a greater premium ($6.48 +/- 0.09 vs. $6.02 +/- 0.08; mean +/- SE) and bull calves received greater discounts ($0.30 +/- 0.14 vs. $1.68 +/- 0.09) in 2005 than in 2000. Breeds types that increased in value from 2000 to 2005 were Angus x Hereford, Angus, Angus x Charolais, and Brahman (P < 0.001). Breed types that received a reduced selling price in 2005 compared with 2000 (P < 0.001) were one-fourth Brahman Cross, Charolais, Charolais x Limousin, Hereford x Limousin, Limousin, Limousin x one-fourth Brahman, Longhorn, Saler and Simmental. Yellow-white face, black-white face, black, and gray feeder calves received an increase in selling price from 2000 to 2005 (P < 0.001). Although fewer horned feeder calves were sold in 2005 (P < 0.01), they received greater discounts in 2005 than 2000 (-$2.86 +/- 0.16 and -$0.51 +/- 0.09; P < 0.001). In 2005, large-framed feeder calves did not receive the premium detected in 2000, but medium-framed feeder calves in 2005 received a greater selling price compared with 2000. Feeder calves with a muscle score of 1 received a greater premium in 2005 compared with 2000 ($2.58 +/- 0.06 and $0.02 +/- 0.09, respectively; P < 0.001). Feeder calves with a muscle score of 2 were discounted in both years, but the discount in 2005 was not as great as in 2000 (P < 0.001). Full and tanked feeder calves received greater discounts in 2005 than in 2000 (P < 0.001). Discounts for fleshy and fat feeder calves were greater in 2005 than in 2000. Most factors affecting the selling price of Arkansas feeder calves in 2000 affected the selling price in 2005. Although feeder calf supplies were smaller in 2005 than 2000, many discounts increased.

Optimal Water-Power Flow Problem: Formulation and Distributed Optimal Solution

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dall-Anese, Emiliano; Zhao, Changhong; Zamzam, Admed S.

This paper formalizes an optimal water-power flow (OWPF) problem to optimize the use of controllable assets across power and water systems while accounting for the couplings between the two infrastructures. Tanks and pumps are optimally managed to satisfy water demand while improving power grid operations; {for the power network, an AC optimal power flow formulation is augmented to accommodate the controllability of water pumps.} Unfortunately, the physics governing the operation of the two infrastructures and coupling constraints lead to a nonconvex (and, in fact, NP-hard) problem; however, after reformulating OWPF as a nonconvex, quadratically-constrained quadratic problem, a feasible point pursuit-successivemore » convex approximation approach is used to identify feasible and optimal solutions. In addition, a distributed solver based on the alternating direction method of multipliers enables water and power operators to pursue individual objectives while respecting the couplings between the two networks. The merits of the proposed approach are demonstrated for the case of a distribution feeder coupled with a municipal water distribution network.« less

The Stingless Bee Melipona solani Deposits a Signature Mixture and Methyl Oleate to Mark Valuable Food Sources.

PubMed

Alavez-Rosas, David; Malo, Edi A; Guzmán, Miguel A; Sánchez-Guillén, Daniel; Villanueva-Gutiérrez, Rogel; Cruz-López, Leopoldo

2017-10-01

Stingless bees foraging for food improve recruitment by depositing chemical cues on valuable food sites or pheromone marks on vegetation. Using gas chromatography/mass spectrometry and bioassays, we showed that Melipona solani foragers leave a mixture composed mostly of long chain hydrocarbons from their abdominal cuticle plus methyl oleate from the labial gland as a scent mark on rich food sites. The composition of hydrocarbons was highly variable among individuals and varied in proportions, depending on the body part. A wide ratio of compounds present in different body parts of the bees elicited electroantennogram responses from foragers and these responses were dose dependent. Generally, in bioassays, these bees prefer to visit previously visited feeders and feeders marked with extracts from any body part of conspecifics. The mean number of visits to a feeder was enhanced when synthetic methyl oleate was added. We propose that this could be a case of multi-source odor marking, in which hydrocarbons, found in large abundance, act as a signature mixture with attraction enhanced through deposition of methyl oleate, which may indicate a rich food source.

Hysteresis, phase transitions, and dangerous transients in electrical power distribution systems

NASA Astrophysics Data System (ADS)

Duclut, Charlie; Backhaus, Scott; Chertkov, Michael

2013-06-01

The majority of dynamical studies in power systems focus on the high-voltage transmission grids where models consider large generators interacting with crude aggregations of individual small loads. However, new phenomena have been observed indicating that the spatial distribution of collective, nonlinear contribution of these small loads in the low-voltage distribution grid is crucial to the outcome of these dynamical transients. To elucidate the phenomenon, we study the dynamics of voltage and power flows in a spatially extended distribution feeder (circuit) connecting many asynchronous induction motors and discover that this relatively simple 1+1 (space+time) dimensional system exhibits a plethora of nontrivial spatiotemporal effects, some of which may be dangerous for power system stability. Long-range motor-motor interactions mediated by circuit voltage and electrical power flows result in coexistence and segregation of spatially extended phases defined by individual motor states, a “normal” state where the motors’ mechanical (rotation) frequency is slightly smaller than the nominal frequency of the basic ac flows and a “stalled” state where the mechanical frequency is small. Transitions between the two states can be initiated by a perturbation of the voltage or base frequency at the head of the distribution feeder. Such behavior is typical of first-order phase transitions in physics, and this 1+1 dimensional model shows many other properties of a first-order phase transition with the spatial distribution of the motors’ mechanical frequency playing the role of the order parameter. In particular, we observe (a) propagation of the phase-transition front with the constant speed (in very long feeders) and (b) hysteresis in transitions between the normal and stalled (or partially stalled) phases.

Hysteresis, phase transitions, and dangerous transients in electrical power distribution systems.

PubMed

Duclut, Charlie; Backhaus, Scott; Chertkov, Michael

2013-06-01

The majority of dynamical studies in power systems focus on the high-voltage transmission grids where models consider large generators interacting with crude aggregations of individual small loads. However, new phenomena have been observed indicating that the spatial distribution of collective, nonlinear contribution of these small loads in the low-voltage distribution grid is crucial to the outcome of these dynamical transients. To elucidate the phenomenon, we study the dynamics of voltage and power flows in a spatially extended distribution feeder (circuit) connecting many asynchronous induction motors and discover that this relatively simple 1+1 (space+time) dimensional system exhibits a plethora of nontrivial spatiotemporal effects, some of which may be dangerous for power system stability. Long-range motor-motor interactions mediated by circuit voltage and electrical power flows result in coexistence and segregation of spatially extended phases defined by individual motor states, a "normal" state where the motors' mechanical (rotation) frequency is slightly smaller than the nominal frequency of the basic ac flows and a "stalled" state where the mechanical frequency is small. Transitions between the two states can be initiated by a perturbation of the voltage or base frequency at the head of the distribution feeder. Such behavior is typical of first-order phase transitions in physics, and this 1+1 dimensional model shows many other properties of a first-order phase transition with the spatial distribution of the motors' mechanical frequency playing the role of the order parameter. In particular, we observe (a) propagation of the phase-transition front with the constant speed (in very long feeders) and (b) hysteresis in transitions between the normal and stalled (or partially stalled) phases.

Application of Advanced Multi-Core Processor Technologies to Oceanographic Research

DTIC Science & Technology

2013-09-30

STM32 NXP LPC series No Proprietary Microchip PIC32/DSPIC No > 500 mW; < 5 W ARM Cortex TI OMAP TI Sitara Broadcom BCM2835 Varies FPGA...1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Application of Advanced Multi-Core Processor Technologies...state-of-the-art information processing architectures. OBJECTIVES Next-generation processor architectures (multi-core, multi-threaded) hold the

Locational Sensitivity Investigation on PV Hosting Capacity and Fast Track PV Screening

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Fei; Mather, Barry; Ainsworth, Nathan

A 15% PV penetration threshold is commonly used by utilities to define photovoltaic (PV) screening methods where PV penetration is defined as the ratio of total solar PV capacity on a line section to peak load. However, this method doesn't take into account PV locational impact or feeder characteristics that could strongly change the feeder's capability to host PVs. This paper investigates the impact of PV location and phase connection type on PV hosting capacity, and then proposes a fast-track PV screening approach that leverages various PV hosting capacity metric responding to different PV locations and types. The proposed studymore » could help utilities to evaluate PV interconnection requests and also help increase the PV hosting capacity of distribution feeders without adverse impacts on system voltages.« less

An Efficacious Multi-Objective Fuzzy Linear Programming Approach for Optimal Power Flow Considering Distributed Generation.

PubMed

Warid, Warid; Hizam, Hashim; Mariun, Norman; Abdul-Wahab, Noor Izzri

2016-01-01

This paper proposes a new formulation for the multi-objective optimal power flow (MOOPF) problem for meshed power networks considering distributed generation. An efficacious multi-objective fuzzy linear programming optimization (MFLP) algorithm is proposed to solve the aforementioned problem with and without considering the distributed generation (DG) effect. A variant combination of objectives is considered for simultaneous optimization, including power loss, voltage stability, and shunt capacitors MVAR reserve. Fuzzy membership functions for these objectives are designed with extreme targets, whereas the inequality constraints are treated as hard constraints. The multi-objective fuzzy optimal power flow (OPF) formulation was converted into a crisp OPF in a successive linear programming (SLP) framework and solved using an efficient interior point method (IPM). To test the efficacy of the proposed approach, simulations are performed on the IEEE 30-busand IEEE 118-bus test systems. The MFLP optimization is solved for several optimization cases. The obtained results are compared with those presented in the literature. A unique solution with a high satisfaction for the assigned targets is gained. Results demonstrate the effectiveness of the proposed MFLP technique in terms of solution optimality and rapid convergence. Moreover, the results indicate that using the optimal DG location with the MFLP algorithm provides the solution with the highest quality.

An Efficacious Multi-Objective Fuzzy Linear Programming Approach for Optimal Power Flow Considering Distributed Generation

PubMed Central

Warid, Warid; Hizam, Hashim; Mariun, Norman; Abdul-Wahab, Noor Izzri

2016-01-01

This paper proposes a new formulation for the multi-objective optimal power flow (MOOPF) problem for meshed power networks considering distributed generation. An efficacious multi-objective fuzzy linear programming optimization (MFLP) algorithm is proposed to solve the aforementioned problem with and without considering the distributed generation (DG) effect. A variant combination of objectives is considered for simultaneous optimization, including power loss, voltage stability, and shunt capacitors MVAR reserve. Fuzzy membership functions for these objectives are designed with extreme targets, whereas the inequality constraints are treated as hard constraints. The multi-objective fuzzy optimal power flow (OPF) formulation was converted into a crisp OPF in a successive linear programming (SLP) framework and solved using an efficient interior point method (IPM). To test the efficacy of the proposed approach, simulations are performed on the IEEE 30-busand IEEE 118-bus test systems. The MFLP optimization is solved for several optimization cases. The obtained results are compared with those presented in the literature. A unique solution with a high satisfaction for the assigned targets is gained. Results demonstrate the effectiveness of the proposed MFLP technique in terms of solution optimality and rapid convergence. Moreover, the results indicate that using the optimal DG location with the MFLP algorithm provides the solution with the highest quality. PMID:26954783

Load Segmentation for Convergence of Distribution Automation and Advanced Metering Infrastructure Systems

NASA Astrophysics Data System (ADS)

Pamulaparthy, Balakrishna; KS, Swarup; Kommu, Rajagopal

2014-12-01

Distribution automation (DA) applications are limited to feeder level today and have zero visibility outside of the substation feeder and reaching down to the low-voltage distribution network level. This has become a major obstacle in realizing many automated functions and enhancing existing DA capabilities. Advanced metering infrastructure (AMI) systems are being widely deployed by utilities across the world creating system-wide communications access to every monitoring and service point, which collects data from smart meters and sensors in short time intervals, in response to utility needs. DA and AMI systems convergence provides unique opportunities and capabilities for distribution grid modernization with the DA system acting as a controller and AMI system acting as feedback to DA system, for which DA applications have to understand and use the AMI data selectively and effectively. In this paper, we propose a load segmentation method that helps the DA system to accurately understand and use the AMI data for various automation applications with a suitable case study on power restoration.

Network-Cognizant Design of Decentralized Volt/VAR Controllers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Baker, Kyri A; Bernstein, Andrey; Zhao, Changhong

This paper considers the problem of designing decentralized Volt/VAR controllers for distributed energy resources (DERs). The voltage-reactive power characteristics of individual DERs are obtained by solving a convex optimization problem, where given performance objectives (e.g., minimization of the voltage deviations from a given profile) are specified and stability constraints are enforced. The resultant Volt/VAR characteristics are network-cognizant, in the sense that they embed information on the location of the DERs and, consequently, on the effect of reactive-power adjustments on the voltages throughout the feeder. Bounds on the maximum voltage deviation incurred by the controllers are analytically established. Numerical results aremore » reported to corroborate the technical findings.« less

Advanced Distribution Network Modelling with Distributed Energy Resources

NASA Astrophysics Data System (ADS)

O'Connell, Alison

The addition of new distributed energy resources, such as electric vehicles, photovoltaics, and storage, to low voltage distribution networks means that these networks will undergo major changes in the future. Traditionally, distribution systems would have been a passive part of the wider power system, delivering electricity to the customer and not needing much control or management. However, the introduction of these new technologies may cause unforeseen issues for distribution networks, due to the fact that they were not considered when the networks were originally designed. This thesis examines different types of technologies that may begin to emerge on distribution systems, as well as the resulting challenges that they may impose. Three-phase models of distribution networks are developed and subsequently utilised as test cases. Various management strategies are devised for the purposes of controlling distributed resources from a distribution network perspective. The aim of the management strategies is to mitigate those issues that distributed resources may cause, while also keeping customers' preferences in mind. A rolling optimisation formulation is proposed as an operational tool which can manage distributed resources, while also accounting for the uncertainties that these resources may present. Network sensitivities for a particular feeder are extracted from a three-phase load flow methodology and incorporated into an optimisation. Electric vehicles are the focus of the work, although the method could be applied to other types of resources. The aim is to minimise the cost of electric vehicle charging over a 24-hour time horizon by controlling the charge rates and timings of the vehicles. The results demonstrate the advantage that controlled EV charging can have over an uncontrolled case, as well as the benefits provided by the rolling formulation and updated inputs in terms of cost and energy delivered to customers. Building upon the rolling optimisation, a three-phase optimal power flow method is developed. The formulation has the capability to provide optimal solutions for distribution system control variables, for a chosen objective function, subject to required constraints. It can, therefore, be utilised for numerous technologies and applications. The three-phase optimal power flow is employed to manage various distributed resources, such as photovoltaics and storage, as well as distribution equipment, including tap changers and switches. The flexibility of the methodology allows it to be applied in both an operational and a planning capacity. The three-phase optimal power flow is employed in an operational planning capacity to determine volt-var curves for distributed photovoltaic inverters. The formulation finds optimal reactive power settings for a number of load and solar scenarios and uses these reactive power points to create volt-var curves. Volt-var curves are determined for 10 PV systems on a test feeder. A universal curve is also determined which is applicable to all inverters. The curves are validated by testing them in a power flow setting over a 24-hour test period. The curves are shown to provide advantages to the feeder in terms of reduction of voltage deviations and unbalance, with the individual curves proving to be more effective. It is also shown that adding a new PV system to the feeder only requires analysis for that system. In order to represent the uncertainties that inherently occur on distribution systems, an information gap decision theory method is also proposed and integrated into the three-phase optimal power flow formulation. This allows for robust network decisions to be made using only an initial prediction for what the uncertain parameter will be. The work determines tap and switch settings for a test network with demand being treated as uncertain. The aim is to keep losses below a predefined acceptable value. The results provide the decision maker with the maximum possible variation in demand for a given acceptable variation in the losses. A validation is performed with the resulting tap and switch settings being implemented, and shows that the control decisions provided by the formulation keep losses below the acceptable value while adhering to the limits imposed by the network.

[Location selection for Shenyang urban parks based on GIS and multi-objective location allocation model].

PubMed

Zhou, Yuan; Shi, Tie-Mao; Hu, Yuan-Man; Gao, Chang; Liu, Miao; Song, Lin-Qi

2011-12-01

Based on geographic information system (GIS) technology and multi-objective location-allocation (LA) model, and in considering of four relatively independent objective factors (population density level, air pollution level, urban heat island effect level, and urban land use pattern), an optimized location selection for the urban parks within the Third Ring of Shenyang was conducted, and the selection results were compared with the spatial distribution of existing parks, aimed to evaluate the rationality of the spatial distribution of urban green spaces. In the location selection of urban green spaces in the study area, the factor air pollution was most important, and, compared with single objective factor, the weighted analysis results of multi-objective factors could provide optimized spatial location selection of new urban green spaces. The combination of GIS technology with LA model would be a new approach for the spatial optimizing of urban green spaces.

Wean-to-finish feeder space availability effects on nursery and finishing pig performance and total tract digestibility in a commercial setting when feeding dried distillers grains with solubles.

PubMed

Weber, E K; Stalder, K J; Patience, J F

2015-04-01

The study objectives were to determine nursery phase feeder space allowance effects on pig performance when double stocked and, second, to determine feeder space allowance and dried distillers grains with solubles (DDGS) inclusion level effects on pig performance and nutrient digestibility during the growing-finishing phase. This study was performed on the same group of pigs within a commercial wean-finish system. For the nursery phase, a completely randomized design was used to compare 3 feeder space allowance treatments (2.1, 2.5, and 2.9 cm/pig). A total of 3,720 pigs were randomly allotted to same-sex pens (10 feeders/treatment) housing 62 pigs/pen. Thirty 7-hole, double-sided feeders were utilized in the study. Differing linear feeder space treatments were established by blocking off sections for the nursery and grow-finish portions of this experiment. All pigs were provided equal floor space (0.26 m2/pig). In the grow-finish phase, a total of 1,860 pigs (n = 60 pens) were utilized in a 2 × 3 factorial design with 3 feeder space allowances (4.1, 4.9, or 5.7 cm/pig) and 2 dietary DDGS treatments (30% [D30] or 60% [D60]). Fecal and diet samples were collected and analyzed to estimate apparent total tract digestibility percentage (ATTD %). In the nursery portion of the trial, there was no feeder space treatment effect on ADG, ADFI, or feed efficiency (P > 0.10) from weaning to d 56 postweaning or during any weigh period. In the grow-finish portion of the trial, feeder space allowance and DDGS inclusion level did not affect ADG, ADFI, or feed efficiency (P > 0.05) from d 57 postweaning to market. Pigs fed the D30 diet had greater HCW, percent yield, and loin depth than those on the D60 diet (P < 0.05). Pigs fed the D30 treatment had greater (P < 0.05) ATTD for DM and GE for both collection periods compared with those on the D60 treatment. In summary, feeder space allowance did not impact pig performance during the nursery or grow-finish production phases. Inclusion of DDGS at higher levels will decrease ADFI but not ADG or efficiency when isocaloric diets are fed. The inclusion level of DDGS does impact HCW and percent yield because of increasing intestinal weights when pigs are fed diets containing increasing DDGS inclusion rates. Dry matter and energy digestibility were greater in pigs fed the lower DDGS treatment.

How Baleen Whales Feed: The Biomechanics of Engulfment and Filtration

NASA Astrophysics Data System (ADS)

Goldbogen, J. A.; Cade, D. E.; Calambokidis, J.; Friedlaender, A. S.; Potvin, J.; Segre, P. S.; Werth, A. J.

2017-01-01

Baleen whales are gigantic obligate filter feeders that exploit aggregations of small-bodied prey in littoral, epipelagic, and mesopelagic ecosystems. At the extreme of maximum body size observed among mammals, baleen whales exhibit a unique combination of high overall energetic demands and low mass-specific metabolic rates. As a result, most baleen whale species have evolved filter-feeding mechanisms and foraging strategies that take advantage of seasonally abundant yet patchily and ephemerally distributed prey resources. New methodologies consisting of multi-sensor tags, active acoustic prey mapping, and hydrodynamic modeling have revolutionized our ability to study the physiology and ecology of baleen whale feeding mechanisms. Here, we review the current state of the field by exploring several hypotheses that aim to explain how baleen whales feed. Despite significant advances, major questions remain about the processes that underlie these extreme feeding mechanisms, which enabled the evolution of the largest animals of all time.

Quantum secured gigabit optical access networks

PubMed Central

Fröhlich, Bernd; Dynes, James F.; Lucamarini, Marco; Sharpe, Andrew W.; Tam, Simon W.-B.; Yuan, Zhiliang; Shields, Andrew J.

2015-01-01

Optical access networks connect multiple endpoints to a common network node via shared fibre infrastructure. They will play a vital role to scale up the number of users in quantum key distribution (QKD) networks. However, the presence of power splitters in the commonly used passive network architecture makes successful transmission of weak quantum signals challenging. This is especially true if QKD and data signals are multiplexed in the passive network. The splitter introduces an imbalance between quantum signal and Raman noise, which can prevent the recovery of the quantum signal completely. Here we introduce a method to overcome this limitation and demonstrate coexistence of multi-user QKD and full power data traffic from a gigabit passive optical network (GPON) for the first time. The dual feeder implementation is compatible with standard GPON architectures and can support up to 128 users, highlighting that quantum protected GPON networks could be commonplace in the future. PMID:26656307

How Baleen Whales Feed: The Biomechanics of Engulfment and Filtration.

PubMed

Goldbogen, J A; Cade, D E; Calambokidis, J; Friedlaender, A S; Potvin, J; Segre, P S; Werth, A J

2017-01-03

Baleen whales are gigantic obligate filter feeders that exploit aggregations of small-bodied prey in littoral, epipelagic, and mesopelagic ecosystems. At the extreme of maximum body size observed among mammals, baleen whales exhibit a unique combination of high overall energetic demands and low mass-specific metabolic rates. As a result, most baleen whale species have evolved filter-feeding mechanisms and foraging strategies that take advantage of seasonally abundant yet patchily and ephemerally distributed prey resources. New methodologies consisting of multi-sensor tags, active acoustic prey mapping, and hydrodynamic modeling have revolutionized our ability to study the physiology and ecology of baleen whale feeding mechanisms. Here, we review the current state of the field by exploring several hypotheses that aim to explain how baleen whales feed. Despite significant advances, major questions remain about the processes that underlie these extreme feeding mechanisms, which enabled the evolution of the largest animals of all time.

The Circulation Analysis of Serial Use: Numbers Game or Key to Service?

PubMed Central

Raisig, L. Miles

1967-01-01

The conventionally erected and reported circulation analysis of serial use in the individual and the feeder library is found to be statistically invalid and misleading, since it measures neither the intellectual use of the serial's contents nor the physical handlings of serial units, and is nonrepresentative of the in-depth library use of serials. It fails utterly to report or even to suggest the relation of intralibrary and interlibrary serial resources. The actual mechanics of the serial use analysis, and the active variables in the library situation which affect serial use, are demonstrated in a simulated analysis and are explained at length. A positive design is offered for the objective gathering and reporting of data on the local intellectual use and physical handling of serials and the relating of resources. Data gathering in the feeder library, and implications for the extension of the feeder library's resources, are discussed. PMID:6055863

A comparison of two systems for chlorinating water in rural Honduras.

PubMed

Henderson, Amy K; Sack, R Bradley; Toledo, Erick

2005-09-01

This study investigated a small subset of the two community water-disinfection systems--hypochlorinators and tablet feeders-in rural Honduras. Levels of residual chlorine were assessed at three locations within the distribution system: the tank, the proximal house, and the distal house. The levels of residual chlorine were compared with the standard guidelines set by the Pan American Health Organization and the International Rural Water Association for potable water that require a minimum of 1.0 (tank), 0.5 (proximal house), and 0.2 (distal house) ppm for each location. The levels of residual chlorine were also compared across systems, e.g. hypochlorinators to tablet feeders. At the tank and proximal house, tablet feeders had significantly higher mean values for levels of residual chlorine (measured in ppm) than hypochlorinators (tank: 1.20 vs 0.67; proximal house: 0.44 vs 0.32, p < 0.001 for both) with no significant difference at the distal house (0.16 vs 0.16). At the tank and proximal house, tablet feeders were more likely to meet recommended standards than hypochlorinators (90.3% vs 13.3%, p < 0.0001 and 41.3% vs 23.7%, p < 0.0001) with a smaller difference seen at the distal house (30.6% vs 27.1%, p = 0.24). The apparent dichotomy in chlorine levels of tablet feeders (e.g. between tank/proximal house and distal house) is discussed. The results suggest that tablet feeders may be more effective than hypochlorinators in supplying clean water in rural, resource-poor settings and possibly serve as an alternative technology for water disinfection. Further research on techniques for empowering and building capacity within community water boards will help organize and introduce sustainable water systems in developing countries.

Thermal analysis of the cryostat feed through for the ITER Tokamak TF feeder

NASA Astrophysics Data System (ADS)

Zhang, Shanwen; Song, Yuntao; Lu, Kun; Wang, Zhongwei; Zhang, Jianfeng; Qin, Yongfa

2017-04-01

In Tokamaks, the toroidal field (TF) coil feeder is an important component that is used to supply the cryogens and electrical power for the TF coils. As a part of the TF feeder, the cryostat-feed through (CFT) is subject to low temperatures of 9 and 80 K inside and room temperature of 300 K outside. Based on the features of the International Thermonuclear Experimental Reactor TF feeder, the thermal performance of the CFT under the nominal conditions is studied. Taking into account the conductive, convective and radiation heat transfer, the finite element model of the CFT is built. Transient thermal analysis is performed to determine the temperatures of the CFT on the 9th day of cooldown. The model is assessed by comparing the cooling curves of the CFT after 9 days. If the simulation and experimental results are the same, the finite element model can be considered as calibrated. The model predicts that the cooling time will be approximately 26 days and the temperature distribution and heat load of the main components are obtained when the CFT reaches thermal equilibrium. This study provides a valid quantitative characterization of the CFT design.

Rainbow trout can discriminate between feeds with different oil sources.

PubMed

Geurden, I; Cuvier, A; Gondouin, E; Olsen, R E; Ruohonen, K; Kaushik, S; Boujard, T

2005-06-02

The purpose of present two-choice trials was to examine the capacity of groups of juvenile rainbow trout to differentiate between two isolipidic diets containing distinct oils and to detect an eventual preference. The choice was offered by means of two self-feeders per tank. One feeder distributed a standard diet with fish oil (FO), the other a diet containing vegetable oil, either rich in linolenic acid (linseed oil, LO), linoleic acid (sunflower oil, SO), or oleic acid (rapeseed oil, RO). Each 15-day preference test was preceded by a 15-day adaptation period during which both feeders distributed the same diet. The tests were followed by a 10- to 15-day validation period in order to confirm that feeder solicitations were steered by the characteristics of the diets. Preferences were expressed as relative changes in feed demands for a specific feeder. Averaged over all groups, the preference tests demonstrated the capacity of rainbow trout to discriminate between a diet with FO and a diet containing vegetable oil, and indicated a general preference for the diet with FO over the other diets irrespective of whether they received the diet with fish oil (Experiment 1) or with vegetable oil (Experiment 2) prior to the preference test. The tests also indicated a difference in the extent of relative avoidance of each of the three vegetable oil diets. Diet LO was the most avoided, as indicated by the 37-39% decrease in demands for the feeder with diet LO (P<0.05). Diet RO was the best accepted, causing a decrease in feed demands of only 15-17% (P>0.05). The avoidance of diet SO at the end of the preference test was 30% (P>0.05) after an initially higher avoidance of 43% (P<0.05). It is believed that the metabolic consequences of the excess of linolenic or linoleic acid negatively affected the feed acceptances of diets LO and SO. Further work is needed to elucidate a possible interference of differences in palatability. In all groups, the lower demands for the vegetable oil diets were compensated by increased demands for diet FO. Hence, changes in diet selection had no effect on total feed or energy intakes, measured as the sum of both selections.

Object-oriented design for accelerator control

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stok, P.D.V. van der; Berk, F. van den; Deckers, R.

1994-02-01

An object-oriented design for the distributed computer control system of the accelerator ring EUTERPE is presented. Because of the experimental nature of the ring, flexibility is of the utmost importance. The object-oriented principles have contributed considerably to the flexibility of the design incorporating multiple views, multi-level access and distributed surveillance.

Road screening and distribution route multi-objective robust optimization for hazardous materials based on neural network and genetic algorithm.

PubMed

Ma, Changxi; Hao, Wei; Pan, Fuquan; Xiang, Wang

2018-01-01

Route optimization of hazardous materials transportation is one of the basic steps in ensuring the safety of hazardous materials transportation. The optimization scheme may be a security risk if road screening is not completed before the distribution route is optimized. For road screening issues of hazardous materials transportation, a road screening algorithm of hazardous materials transportation is built based on genetic algorithm and Levenberg-Marquardt neural network (GA-LM-NN) by analyzing 15 attributes data of each road network section. A multi-objective robust optimization model with adjustable robustness is constructed for the hazardous materials transportation problem of single distribution center to minimize transportation risk and time. A multi-objective genetic algorithm is designed to solve the problem according to the characteristics of the model. The algorithm uses an improved strategy to complete the selection operation, applies partial matching cross shift and single ortho swap methods to complete the crossover and mutation operation, and employs an exclusive method to construct Pareto optimal solutions. Studies show that the sets of hazardous materials transportation road can be found quickly through the proposed road screening algorithm based on GA-LM-NN, whereas the distribution route Pareto solutions with different levels of robustness can be found rapidly through the proposed multi-objective robust optimization model and algorithm.

Research into a distributed fault diagnosis system and its application

NASA Astrophysics Data System (ADS)

Qian, Suxiang; Jiao, Weidong; Lou, Yongjian; Shen, Xiaomei

2005-12-01

CORBA (Common Object Request Broker Architecture) is a solution to distributed computing methods over heterogeneity systems, which establishes a communication protocol between distributed objects. It takes great emphasis on realizing the interoperation between distributed objects. However, only after developing some application approaches and some practical technology in monitoring and diagnosis, can the customers share the monitoring and diagnosis information, so that the purpose of realizing remote multi-expert cooperation diagnosis online can be achieved. This paper aims at building an open fault monitoring and diagnosis platform combining CORBA, Web and agent. Heterogeneity diagnosis object interoperate in independent thread through the CORBA (soft-bus), realizing sharing resource and multi-expert cooperation diagnosis online, solving the disadvantage such as lack of diagnosis knowledge, oneness of diagnosis technique and imperfectness of analysis function, so that more complicated and further diagnosis can be carried on. Take high-speed centrifugal air compressor set for example, we demonstrate a distributed diagnosis based on CORBA. It proves that we can find out more efficient approaches to settle the problems such as real-time monitoring and diagnosis on the net and the break-up of complicated tasks, inosculating CORBA, Web technique and agent frame model to carry on complemental research. In this system, Multi-diagnosis Intelligent Agent helps improve diagnosis efficiency. Besides, this system offers an open circumstances, which is easy for the diagnosis objects to upgrade and for new diagnosis server objects to join in.

Distributed Market-Based Algorithms for Multi-Agent Planning with Shared Resources

DTIC Science & Technology

2013-02-01

1 Introduction 1 2 Distributed Market-Based Multi-Agent Planning 5 2.1 Problem Formulation...over the deterministic planner, on the “test set” of scenarios with changing economies. . . 50 xi xii Chapter 1 Introduction Multi-agent planning is...representation of the objective (4.2.1). For example, for the supply chain mangement problem, we assumed a sequence of Bernoulli coin flips, which seems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Narang, David; Ayyanar, Raja; Gemin, Paul

APS’s renewable energy portfolio, driven in part by Arizona’s Renewable Energy Standard (RES) currently includes more than 1100 MW of installed capacity, equating to roughly 3000 GWh of annual production. Overall renewable production is expected to grow to 6000 GWh by 2025. It is expected that distributed photovoltaics, driven primarily by lower cost, will contribute to much of this growth and that by 2025, distributed installations will account for half of all renewable production (3000GHW). As solar penetration increases, additional analysis may be required for routine utility processes to ensure continued safe and reliable operation of the electric distribution network.more » Such processes include residential or commercial interconnection requests and load shifting during normal feeder operations. Circuits with existing high solar penetration will also have to be studied and results will need to be evaluated for adherence to utility practices or strategy. Increased distributed PV penetration may offer benefits such as load offsetting, but it also has the potential to adversely impact distribution system operation. These effects may be exacerbated by the rapid variability of PV production. Detailed effects of these phenomena in distributed PV applications continue to be studied. Comprehensive, high-resolution electrical models of the distribution system were developed to analyze the impacts of PV on distribution circuit protection systems (including coordination and anti-islanding), predict voltage regulation and phase balance issues, and develop volt/VAr control schemes. Modeling methods were refined by validating against field measurements. To augment the field measurements, methods were developed to synthesize high resolution load and PV generation data to facilitate quasi-static time series simulations. The models were then extended to explore boundary conditions for PV hosting capability of the feeder and to simulate common utility practices such as feeder reconfiguration. The modeling and analysis methodology was implemented using open source tools and a process was developed to aid utility engineers in future interconnection requests. Methods to increase PV hosting capacity were also explored during the course of the study. A 700kVA grid-supportive inverter was deployed on the feeder and each grid support mode was demonstrated. Energy storage was explored through simulation and models were developed to calculate the optimum size and placement needed to increase PV hosting capacity. A tool was developed to aid planners in assigning relative costs and benefits to various strategies for increasing PV hosting capacity beyond current levels. Following the completion of the project, APS intends to use the tools and methods to improve the framework of future PV integration on its system. The tools and methods are also expected to aid other utilities to accelerate distributed PV deployment.« less

Considering Decision Variable Diversity in Multi-Objective Optimization: Application in Hydrologic Model Calibration

NASA Astrophysics Data System (ADS)

Sahraei, S.; Asadzadeh, M.

2017-12-01

Any modern multi-objective global optimization algorithm should be able to archive a well-distributed set of solutions. While the solution diversity in the objective space has been explored extensively in the literature, little attention has been given to the solution diversity in the decision space. Selection metrics such as the hypervolume contribution and crowding distance calculated in the objective space would guide the search toward solutions that are well-distributed across the objective space. In this study, the diversity of solutions in the decision-space is used as the main selection criteria beside the dominance check in multi-objective optimization. To this end, currently archived solutions are clustered in the decision space and the ones in less crowded clusters are given more chance to be selected for generating new solution. The proposed approach is first tested on benchmark mathematical test problems. Second, it is applied to a hydrologic model calibration problem with more than three objective functions. Results show that the chance of finding more sparse set of high-quality solutions increases, and therefore the analyst would receive a well-diverse set of options with maximum amount of information. Pareto Archived-Dynamically Dimensioned Search, which is an efficient and parsimonious multi-objective optimization algorithm for model calibration, is utilized in this study.

A risk-based multi-objective model for optimal placement of sensors in water distribution system

NASA Astrophysics Data System (ADS)

Naserizade, Sareh S.; Nikoo, Mohammad Reza; Montaseri, Hossein

2018-02-01

In this study, a new stochastic model based on Conditional Value at Risk (CVaR) and multi-objective optimization methods is developed for optimal placement of sensors in water distribution system (WDS). This model determines minimization of risk which is caused by simultaneous multi-point contamination injection in WDS using CVaR approach. The CVaR considers uncertainties of contamination injection in the form of probability distribution function and calculates low-probability extreme events. In this approach, extreme losses occur at tail of the losses distribution function. Four-objective optimization model based on NSGA-II algorithm is developed to minimize losses of contamination injection (through CVaR of affected population and detection time) and also minimize the two other main criteria of optimal placement of sensors including probability of undetected events and cost. Finally, to determine the best solution, Preference Ranking Organization METHod for Enrichment Evaluation (PROMETHEE), as a subgroup of Multi Criteria Decision Making (MCDM) approach, is utilized to rank the alternatives on the trade-off curve among objective functions. Also, sensitivity analysis is done to investigate the importance of each criterion on PROMETHEE results considering three relative weighting scenarios. The effectiveness of the proposed methodology is examined through applying it to Lamerd WDS in the southwestern part of Iran. The PROMETHEE suggests 6 sensors with suitable distribution that approximately cover all regions of WDS. Optimal values related to CVaR of affected population and detection time as well as probability of undetected events for the best optimal solution are equal to 17,055 persons, 31 mins and 0.045%, respectively. The obtained results of the proposed methodology in Lamerd WDS show applicability of CVaR-based multi-objective simulation-optimization model for incorporating the main uncertainties of contamination injection in order to evaluate extreme value of losses in WDS.

Pacific Northwest GridWise™ Testbed Demonstration Projects; Part I. Olympic Peninsula Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hammerstrom, Donald J.; Ambrosio, Ron; Carlon, Teresa A.

2008-01-09

This report describes the implementation and results of a field demonstration wherein residential electric water heaters and thermostats, commercial building space conditioning, municipal water pump loads, and several distributed generators were coordinated to manage constrained feeder electrical distribution through the two-way communication of load status and electric price signals. The field demonstration took place in Washington and Oregon and was paid for by the U.S. Department of Energy and several northwest utilities. Price is found to be an effective control signal for managing transmission or distribution congestion. Real-time signals at 5-minute intervals are shown to shift controlled load in time.more » The behaviors of customers and their responses under fixed, time-of-use, and real-time price contracts are compared. Peak loads are effectively reduced on the experimental feeder. A novel application of portfolio theory is applied to the selection of an optimal mix of customer contract types.« less

A method for optimizing multi-objective reservoir operation upon human and riverine ecosystem demands

NASA Astrophysics Data System (ADS)

Ai, Xueshan; Dong, Zuo; Mo, Mingzhu

2017-04-01

The optimal reservoir operation is in generally a multi-objective problem. In real life, most of the reservoir operation optimization problems involve conflicting objectives, for which there is no single optimal solution which can simultaneously gain an optimal result of all the purposes, but rather a set of well distributed non-inferior solutions or Pareto frontier exists. On the other hand, most of the reservoirs operation rules is to gain greater social and economic benefits at the expense of ecological environment, resulting to the destruction of riverine ecology and reduction of aquatic biodiversity. To overcome these drawbacks, this study developed a multi-objective model for the reservoir operating with the conflicting functions of hydroelectric energy generation, irrigation and ecological protection. To solve the model with the objectives of maximize energy production, maximize the water demand satisfaction rate of irrigation and ecology, we proposed a multi-objective optimization method of variable penalty coefficient (VPC), which was based on integrate dynamic programming (DP) with discrete differential dynamic programming (DDDP), to generate a well distributed non-inferior along the Pareto front by changing the penalties coefficient of different objectives. This method was applied to an existing China reservoir named Donggu, through a course of a year, which is a multi-annual storage reservoir with multiple purposes. The case study results showed a good relationship between any two of the objectives and a good Pareto optimal solutions, which provide a reference for the reservoir decision makers.

Optimizing DER Participation in Inertial and Primary-Frequency Response

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dall-Anese, Emiliano; Zhao, Changhong; Guggilam, Swaroop

This paper develops an approach to enable the optimal participation of distributed energy resources (DERs) in inertial and primary-frequency response alongside conventional synchronous generators. Leveraging a reduced-order model description of frequency dynamics, DERs' synthetic inertias and droop coefficients are designed to meet time-domain performance objectives of frequency overshoot and steady-state regulation. Furthermore, an optimization-based method centered around classical economic dispatch is developed to ensure that DERs share the power injections for inertial- and primary-frequency response in proportion to their power ratings. Simulations for a modified New England test-case system composed of ten synchronous generators and six instances of the IEEEmore » 37-node test feeder with frequency-responsive DERs validate the design strategy.« less

Identifying calcium sources at an acid deposition-impacted spruce forest: a strontium isotope, alkaline earth element multi-tracer approach

Treesearch

Thomas D. Bullen; Scott W. Bailey

2005-01-01

Depletion of calcium from forest soils has important implications for forest productivity and health. Ca is available to fine feeder roots from a number of soil organic and mineral sources. but identifying the primary source or changes of sources in response to environmental change is problematic. We used strontium isotope and alkaline earth element concentration...

International Conference on Antenna Theory and Techniques

DTIC Science & Technology

1999-12-03

modeling; (5) mobile —nicaWon^a^nas^ radane? and absorbing coatings; (7) antenna measurements; (8) microwave ccmponents and feeders; (9 SSrial^d...LOW-GAIN ANTENNAS PRINTED ANTENNAS ANTENNAS FOR MOBILE COMMUNICATIONS 299 Radiation of the multi-mode slotted radiator V. Antyfeev, A. Borsov, A...band antenna alternatives for the European mobile satellite (EMSAT) network G. de Balbine (Tarzana, USA) 304 Optimization of characteristics of

Systems and methods for detecting an image of an object using multi-beam imaging from an X-ray beam having a polychromatic distribution

DOEpatents

Parham, Christopher A; Zhong, Zhong; Pisano, Etta; Connor, Jr., Dean M

2015-03-03

Systems and methods for detecting an image of an object using a multi-beam imaging system from an x-ray beam having a polychromatic energy distribution are disclosed. According to one aspect, a method can include generating a first X-ray beam having a polychromatic energy distribution. Further, the method can include positioning a plurality of monochromator crystals in a predetermined position to directly intercept the first X-ray beam such that a plurality of second X-ray beams having predetermined energy levels are produced. Further, an object can be positioned in the path of the second X-ray beams for transmission of the second X-ray beams through the object and emission from the object as transmitted X-ray beams. The transmitted X-ray beams can each be directed at an angle of incidence upon one or more crystal analyzers. Further, an image of the object can be detected from the beams diffracted from the analyzer crystals.

Initial Studies of the Bidirectional Reflectance Distribution Function of Multi-Walled Carbon Nanotube Structures for Stray Light Control Applications

NASA Technical Reports Server (NTRS)

Butler, J. J.; Tveekrem, J. L.; Quijada, M. A.; Getty, S. A.; Hagopian, J. G.; Georglev, G. T.

2010-01-01

The presentation examines the application of low reflectance surfaces in optical instruments, multi-walled carbon nanotubes (MWCNTs), research objects, MWCNT samples, measurement of 8 deg. directional/hemispherical reflectance, measurement of bidirectional reflectance distribution function (BRDF), and what is current the "blackest ever black".

Comparing Different Fault Identification Algorithms in Distributed Power System

NASA Astrophysics Data System (ADS)

Alkaabi, Salim

A power system is a huge complex system that delivers the electrical power from the generation units to the consumers. As the demand for electrical power increases, distributed power generation was introduced to the power system. Faults may occur in the power system at any time in different locations. These faults cause a huge damage to the system as they might lead to full failure of the power system. Using distributed generation in the power system made it even harder to identify the location of the faults in the system. The main objective of this work is to test the different fault location identification algorithms while tested on a power system with the different amount of power injected using distributed generators. As faults may lead the system to full failure, this is an important area for research. In this thesis different fault location identification algorithms have been tested and compared while the different amount of power is injected from distributed generators. The algorithms were tested on IEEE 34 node test feeder using MATLAB and the results were compared to find when these algorithms might fail and the reliability of these methods.

Multi-objective optimization to predict muscle tensions in a pinch function using genetic algorithm

NASA Astrophysics Data System (ADS)

Bensghaier, Amani; Romdhane, Lotfi; Benouezdou, Fethi

2012-03-01

This work is focused on the determination of the thumb and the index finger muscle tensions in a tip pinch task. A biomechanical model of the musculoskeletal system of the thumb and the index finger is developed. Due to the assumptions made in carrying out the biomechanical model, the formulated force analysis problem is indeterminate leading to an infinite number of solutions. Thus, constrained single and multi-objective optimization methodologies are used in order to explore the muscular redundancy and to predict optimal muscle tension distributions. Various models are investigated using the optimization process. The basic criteria to minimize are the sum of the muscle stresses, the sum of individual muscle tensions and the maximum muscle stress. The multi-objective optimization is solved using a Pareto genetic algorithm to obtain non-dominated solutions, defined as the set of optimal distributions of muscle tensions. The results show the advantage of the multi-objective formulation over the single objective one. The obtained solutions are compared to those available in the literature demonstrating the effectiveness of our approach in the analysis of the fingers musculoskeletal systems when predicting muscle tensions.

Selectivity of end-Cretaceous marine bivalve extinctions

NASA Technical Reports Server (NTRS)

Jablonski, D.; Raup, D. M.

1995-01-01

Analyses of the end-Cretaceous or Cretaceous-Tertiary mass extinction show no selectivity of marine bivalve genera by life position (burrowing versus exposed), body size, bathymetric position on the continental shelf, or relative breadth of bathymetric range. Deposit-feeders as a group have significantly lower extinction intensities than suspension-feeders, but this pattern is due entirely to low extinction in two groups (Nuculoida and Lucinoidea), which suggests that survivorship was not simply linked to feeding mode. Geographically widespread genera have significantly lower extinction intensities than narrowly distributed genera. These results corroborate earlier work suggesting that some biotic factors that enhance survivorship during times of lesser extinction intensities are ineffectual during mass extinctions.

Canine corneal epithelial cells possess a sustained proliferative capacity and generate a spontaneously derived cell line.

PubMed

Morita, Maresuke; Fujita, Naoki; Abe, Momoko; Hayashimoto, Koji; Nakagawa, Takayuki; Nishimura, Ryohei; Tsuzuki, Keiko

2018-06-01

We have previously reported characteristics of canine corneal epithelial cells in vitro and found that canine corneal epithelial cells could maintain their proliferative capacity even after continuous culture without the use of feeder cells and growth promoting additives. The objective of this study was to elucidate proliferative characteristics of canine corneal epithelial cells independent of feeder cells and growth promoting additives, with the aim of developing a spontaneously derived corneal epithelial cell line. Canine and rabbit corneal epithelial cells were harvested from the limbus and cultured with, or without, feeder cells and growth promoting additives, and both were passaged continuously until growth arrest. Canine corneal epithelial cells could proliferate independently, and could be passaged more times than rabbit cells. A canine corneal epithelial cell line, cCEpi, which could be passaged more than 100 times without using feeder cells and growth promoting additives, was established. cCEpi cells maintained a cell morphology close to the primary culture and expressed p63, cytokeratin 15 (K15), and K3. Although changes in colony morphology, shortening of the population doubling time and a heteroploid karyotype were observed, cCEpi was not tumorigenic. Stratified cell sheets cultured from cCEpi were morphologically and immunohistologically similar to sheets cultivated from early passage cells. In conclusion, canine corneal epithelial cells can proliferate independent of feeder cells and growth promoting additives. cCEpi maintains properties similar to normal corneal epithelial cells and could be a useful source for studies in cellular biology and for developing novel therapies. Copyright © 2018 Elsevier Ltd. All rights reserved.

Multi-objective Calibration of DHSVM Based on Hydrologic Key Elements in Jinhua River Basin, East China

NASA Astrophysics Data System (ADS)

Pan, S.; Liu, L.; Xu, Y. P.

2017-12-01

Abstract: In physically based distributed hydrological model, large number of parameters, representing spatial heterogeneity of watershed and various processes in hydrologic cycle, are involved. For lack of calibration module in Distributed Hydrology Soil Vegetation Model, this study developed a multi-objective calibration module using Epsilon-Dominance Non-Dominated Sorted Genetic Algorithm II (ɛ-NSGAII) and based on parallel computing of Linux cluster for DHSVM (ɛP-DHSVM). In this study, two hydrologic key elements (i.e., runoff and evapotranspiration) are used as objectives in multi-objective calibration of model. MODIS evapotranspiration obtained by SEBAL is adopted to fill the gap of lack of observation for evapotranspiration. The results show that good performance of runoff simulation in single objective calibration cannot ensure good simulation performance of other hydrologic key elements. Self-developed ɛP-DHSVM model can make multi-objective calibration more efficiently and effectively. The running speed can be increased by more than 20-30 times via applying ɛP-DHSVM. In addition, runoff and evapotranspiration can be simulated very well simultaneously by ɛP-DHSVM, with superior values for two efficiency coefficients (0.74 for NS of runoff and 0.79 for NS of evapotranspiration, -10.5% and -8.6% for PBIAS of runoff and evapotranspiration respectively).

Surgical planning for microsurgical excision of cerebral arterio-venous malformations using virtual reality technology.

PubMed

Ng, Ivan; Hwang, Peter Y K; Kumar, Dinesh; Lee, Cheng Kiang; Kockro, Ralf A; Sitoh, Y Y

2009-05-01

To evaluate the feasibility of surgical planning using a virtual reality platform workstation in the treatment of cerebral arterio-venous malformations (AVMs) Patient-specific data of multiple imaging modalities were co-registered, fused and displayed as a 3D stereoscopic object on the Dextroscope, a virtual reality surgical planning platform. This system allows for manipulation of 3D data and for the user to evaluate and appreciate the angio-architecture of the nidus with regards to position and spatial relationships of critical feeders and draining veins. We evaluated the ability of the Dextroscope to influence surgical planning by providing a better understanding of the angio-architecture as well as its impact on the surgeon's pre- and intra-operative confidence and ability to tackle these lesions. Twenty four patients were studied. The mean age was 29.65 years. Following pre-surgical planning on the Dextroscope, 23 patients underwent microsurgical resection after pre-surgical virtual reality planning, during which all had documented complete resection of the AVM. Planning on the virtual reality platform allowed for identification of critical feeders and draining vessels in all patients. The appreciation of the complex patient specific angio-architecture to establish a surgical plan was found to be invaluable in the conduct of the procedure and was found to enhance the surgeon's confidence significantly. Surgical planning of resection of an AVM with a virtual reality system allowed detailed and comprehensive analysis of 3D multi-modality imaging data and, in our experience, proved very helpful in establishing a good surgical strategy, enhancing intra-operative spatial orientation and increasing surgeon's confidence.

Energy Systems Integration: Demonstrating Distribution Feeder Voltage Control

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-01-01

Overview fact sheet about the Smarter Grid Solutions Integrated Network Testbed for Energy Grid Research and Technology Experimentation (INTEGRATE) project at the Energy Systems Integration Facility. INTEGRATE is part of the U.S. Department of Energy's Grid Modernization Initiative.

An investigation of the maximum penetration level of a photovoltaic (PV) system into a traditional distribution grid

NASA Astrophysics Data System (ADS)

Chalise, Santosh

Although solar photovoltaic (PV) systems have remained the fastest growing renewable power generating technology, variability as well as uncertainty in the output of PV plants is a significant issue. This rapid increase in PV grid-connected generation presents not only progress in clean energy but also challenges in integration with traditional electric power grids which were designed for transmission and distribution of power from central stations. Unlike conventional electric generators, PV panels do not have rotating parts and thus have no inertia. This potentially causes a problem when the solar irradiance incident upon a PV plant changes suddenly, for example, when scattered clouds pass quickly overhead. The output power of the PV plant may fluctuate nearly as rapidly as the incident irradiance. These rapid power output fluctuations may then cause voltage fluctuations, frequency fluctuations, and power quality issues. These power quality issues are more severe with increasing PV plant power output. This limits the maximum power output allowed from interconnected PV plants. Voltage regulation of a distribution system, a focus of this research, is a prime limiting factor in PV penetration levels. The IEEE 13-node test feeder, modeled and tested in the MATLAB/Simulink environment, was used as an example distribution feeder to analyze the maximum acceptable penetration of a PV plant. The effect of the PV plant's location was investigated, along with the addition of a VAR compensating device (a D-STATCOM in this case). The results were used to develop simple guidelines for determining an initial estimate of the maximum PV penetration level on a distribution feeder. For example, when no compensating devices are added to the system, a higher level of PV penetration is generally achieved by installing the PV plant close to the substation. The opposite is true when a VAR compensator is installed with the PV plant. In these cases, PV penetration levels over 50% may be safely achieved.

95. VIEW OF ZINC FEEDER FROM SOUTHEAST. NOTE FEEDER CONE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

95. VIEW OF ZINC FEEDER FROM SOUTHEAST. NOTE FEEDER CONE AND PIPING FROM VACUUM RECEIVER ON LEFT. PRECIPITATE PUMP MOTOR MOUNT VISIBLE BELOW FEEDER STAIRS, PUMP AND MOTOR MISSING. SUMPS ARE LOCATED UNDER THIS FLOOR, WITH ACCESS TO HATCH TO THE RIGHT OF FEEDER STAIR. - Bald Mountain Gold Mill, Nevada Gulch at head of False Bottom Creek, Lead, Lawrence County, SD

Hygiene at winter bird feeders in a southwestern Ontario city.

PubMed Central

Prescott, J F; Hunter, D B; Campbell, G D

2000-01-01

To further understand the source of the epidemic of salmonellosis in some species of birds using bird feeders in southern Ontario in the winter of 1997-1998, 124 bird feeder stations were examined for their state of hygiene and for Salmonella on 5 occasions during the winter of 1999 in a city of 100,000 people in southwestern Ontario. No Salmonella were isolated from feed contaminated with feces recovered from the feeders. Squirrel-proof feeders were significantly less contaminated with feces than were other feeder types (hopper, platform, silo), which did not differ significantly in their hygiene scores. Contamination of squirrel-proof feeders increased significantly through the course of the study, but other feeder types showed no significant change. Hygiene was poorer if feeders were maintained equally by both male and female household members, particularly as they grew older, but no age or gender effect was observed if only one person was largely responsible for maintaining the feeders. We concluded that winter bird feeder stations in a southern Ontario city were not contaminated with Salmonella but that bird feeder stations could be designed better to reduce fecal contamination of feed. PMID:10992987

Diversity and feeding strategies of soil microfauna along elevation gradients in Himalayan cold deserts

PubMed Central

Háněl, Ladislav; Řeháková, Klára; Doležal, Jiří

2017-01-01

High-elevation cold deserts in Tibet and Himalaya are one of the most extreme environments. One consequence is that the diversity of macrofauna in this environment is often limited, and soil microorganisms have a more influential role in governing key surface and subsurface bioprocesses. High-elevation soil microfauna represent important components of cold ecosystems and dominant consumers of microbial communities. Still little is known about their diversity and distribution on the edge of their reproductive and metabolic abilities. In this study, we disentangle the impact of elevation and soil chemistry on diversity and distribution of rotifers, nematodes and tardigrades and their most frequent feeding strategies (microbial filter-feeders, bacterivores, fungivores, root-fungal feeders, omnivores) along two contrasting altitudinal gradients in Indian NW Himalaya (Zanskar transect from 3805 to 4714 m a.s.l.) and southwestern Tibet (Tso Moriri transect from 4477 to 6176 m a.s.l.), using a combination of multivariate analysis, variation partitioning and generalized additive models. Zanskar transect had higher precipitation, soil moisture, organic matter and available nutrients than dry Tso Moriri transect. In total, 40 species of nematodes, 19 rotifers and 1 tardigrade were discovered. Species richness and total abundance of rotifers and nematodes showed mid-elevation peaks in both investigated transects. The optimum for rotifers was found at higher elevation than for nematodes. Diversity and distribution of soil microfauna was best explained by soil nitrogen, phosphorus and organic matter. More fertile soils hosted more diverse and abundant faunal communities. In Tso Moriri, bacterivores represented 60% of all nematodes, fungivores 35%, root-fungal feeders 1% and omnivores 3%. For Zanskar the respective proportions were 21%, 13%, 56% and 9%. Elevational optima of different feeding strategies occurred in Zanskar in one elevation zone (4400–4500 m), while in Tso Moriri each feeding strategy had their unique optima with fungivores at 5300 m (steppes), bacterivores at 5500 m (alpine grassland), filter-feeders at 5600 m and predators and omnivores above 5700 m (subnival zone). Our results shed light on the diversity of microfauna in the high-elevation cold deserts and disentangle the role of different ecological filters in structuring microfaunal communities in the rapidly-warming Himalayas. PMID:29131839

Hardware-in-the-Loop Simulation of a Distribution System with Air Conditioners under Model Predictive Control: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sparn, Bethany F; Ruth, Mark F; Krishnamurthy, Dheepak

Many have proposed that responsive load provided by distributed energy resources (DERs) and demand response (DR) are an option to provide flexibility to the grid and especially to distribution feeders. However, because responsive load involves a complex interplay between tariffs and DER and DR technologies, it is challenging to test and evaluate options without negatively impacting customers. This paper describes a hardware-in-the-loop (HIL) simulation system that has been developed to reduce the cost of evaluating the impact of advanced controllers (e.g., model predictive controllers) and technologies (e.g., responsive appliances). The HIL simulation system combines large-scale software simulation with a smallmore » set of representative building equipment hardware. It is used to perform HIL simulation of a distribution feeder and the loads on it under various tariff structures. In the reported HIL simulation, loads include many simulated air conditioners and one physical air conditioner. Independent model predictive controllers manage operations of all air conditioners under a time-of-use tariff. Results from this HIL simulation and a discussion of future development work of the system are presented.« less

Microgrids for Service Restoration to Critical Load in a Resilient Distribution System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Yin; Liu, Chen-Ching; Schneider, Kevin P.

icrogrids can act as emergency sources to serve critical loads when utility power is unavailable. This paper proposes a resiliency-based methodology that uses microgrids to restore critical loads on distribution feeders after a major disaster. Due to limited capacity of distributed generators (DGs) within microgrids, dynamic performance of the DGs during the restoration process becomes essential. In this paper, the stability of microgrids, limits on frequency deviation, and limits on transient voltage and current of DGs are incorporated as constraints of the critical load restoration problem. The limits on the amount of generation resources within microgrids are also considered. Bymore » introducing the concepts of restoration tree and load group, restoration of critical loads is transformed into a maximum coverage problem, which is a linear integer program (LIP). The restoration paths and actions are determined for critical loads by solving the LIP. A 4-feeder, 1069-bus unbalanced test system with four microgrids is utilized to demonstrate the effectiveness of the proposed method. The method is applied to the distribution system in Pullman, WA, resulting in a strategy that uses generators on the Washington State University campus to restore service to the Hospital and City Hall in Pullman.« less

A Multi-level Fuzzy Evaluation Method for Smart Distribution Network Based on Entropy Weight

NASA Astrophysics Data System (ADS)

Li, Jianfang; Song, Xiaohui; Gao, Fei; Zhang, Yu

2017-05-01

Smart distribution network is considered as the future trend of distribution network. In order to comprehensive evaluate smart distribution construction level and give guidance to the practice of smart distribution construction, a multi-level fuzzy evaluation method based on entropy weight is proposed. Firstly, focus on both the conventional characteristics of distribution network and new characteristics of smart distribution network such as self-healing and interaction, a multi-level evaluation index system which contains power supply capability, power quality, economy, reliability and interaction is established. Then, a combination weighting method based on Delphi method and entropy weight method is put forward, which take into account not only the importance of the evaluation index in the experts’ subjective view, but also the objective and different information from the index values. Thirdly, a multi-level evaluation method based on fuzzy theory is put forward. Lastly, an example is conducted based on the statistical data of some cites’ distribution network and the evaluation method is proved effective and rational.

Real-time modeling and simulation of distribution feeder and distributed resources

NASA Astrophysics Data System (ADS)

Singh, Pawan

The analysis of the electrical system dates back to the days when analog network analyzers were used. With the advent of digital computers, many programs were written for power-flow and short circuit analysis for the improvement of the electrical system. Real-time computer simulations can answer many what-if scenarios in the existing or the proposed power system. In this thesis, the standard IEEE 13-Node distribution feeder is developed and validated on a real-time platform OPAL-RT. The concept and the challenges of the real-time simulation are studied and addressed. Distributed energy resources include some of the commonly used distributed generation and storage devices like diesel engine, solar photovoltaic array, and battery storage system are modeled and simulated on a real-time platform. A microgrid encompasses a portion of an electric power distribution which is located downstream of the distribution substation. Normally, the microgrid operates in paralleled mode with the grid; however, scheduled or forced isolation can take place. In such conditions, the microgrid must have the ability to operate stably and autonomously. The microgrid can operate in grid connected and islanded mode, both the operating modes are studied in the last chapter. Towards the end, a simple microgrid controller modeled and simulated on the real-time platform is developed for energy management and protection for the microgrid.

Design of Interline Unified Power Quality Conditioner for Power Quality Disturbances using Simulink

NASA Astrophysics Data System (ADS)

Kumaraswamy, G.; Reddy, Y. Rajasekhar; Harikrishna, Ch.

2012-10-01

Proliferation of electronic equipment in commercial and industrial processes has resulted in increasingly sensitive electrical loads to be fed from power distribution system which introduce contamination to voltage and current waveforms at the point of common coupling of industrial loads. The unified power quality conditioner (UPQC) is connected between two different feeders (lines), hence this method of connection of the UPQC is called as Interline UPQC (IUPQC).This paper proposes a new connection for a UPQC to improve the power quality of two feeders in a distribution system. Interline Unified Power Quality Conditioner (IUPQC), specifically aims at the integration of series VSC and Shunt VSC to provide high quality power supply by means of voltage sag/swell compensation, harmonic elimination and power factor correction in a power distribution network, so that improved power quality can be made available at the point of common coupling. The structure, control and capability of the IUPQC are discussed in this paper. The efficiency of the proposed configuration has been verified through simulation using MATLAB/ SIMULINK.

Effect of stall design on dairy calf transition to voluntary feeding on an automatic milk feeder after introduction to group housing.

PubMed

Wilson, Tanya R; LeBlanc, Stephen J; DeVries, Trevor J; Haley, Derek B

2018-06-01

Automatic milk feeders (AMF) for young dairy calves are widely used in the dairy industry. These feeders are thought to have benefits for calf health and welfare and may reduce labor required for feeding; however, little is known about how calves adapt to feeding with AMF. The objective of this study was to observe the effects of feeding stall design on calves learning to use the AMF. The hypothesis was that solid side stalls, compared with steel bar stalls, would result in a longer latency to approach and feed from the AMF without assistance. A total of 147 Holstein calves (80 male and 67 female) were enrolled at 4 d of age, introduced to a group pen, and, at the same time, trained on an AMF. For training, calves were allowed to suck on the trainer's fingers and guided to the teat. Calves were allocated to 1 of 2 stall designs at the pen level, depending on which treatment cohort they were born into, either with steel bar stall walls (n = 46 male, 34 female calves) or with solid side stall walls (n = 34 male, 33 female calves). For 72 h after introductory training on the AMF, data from the feeders were collected and calf behavior was monitored by video. Outcomes measured included latency to first voluntary visit to the feeder and to first feeding, time spent in the feeder, amount of milk consumed over 72 h, number of retraining sessions required (retrained if <2 L was consumed every 12 h), and exploratory behavior, such as sniffing and licking of the feeder. Data were analyzed using mixed effects linear regression models or a Poisson model for the outcome of retraining. For certain outcomes the effects of stall design interacted with difficulty of training (willingness to enter feeder and drink); for the 38% of calves that were scored as moderately difficult to train on a scale of easy, moderate, or difficult, treatment (stall design) differences were detected. These calves took 2× longer to lick or bite toward the nipple, 2× longer to first voluntarily feeding, and consumed less milk over 72 h following training when trained on the steel bar stall design. These results suggest simple features of a stall may influence how quickly calves learn to use an AMF, but that the influence of stall wall design was affected by how easy calves were to train on the feeder upon initial introduction, which may depend in part on certain aspects of calf temperament. For many calves, solid side stalls at an AMF resulted faster in adaption than the steel bar stalls. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Granular Material Scoop and Near-Vertical Lifting Feeder/Conveyor

NASA Technical Reports Server (NTRS)

Walton, Otis (Inventor); Vollmer, Hubert J. (Inventor)

2017-01-01

An integrated granular-material scoop and near-vertical lifting feeder/conveyor includes special connections and skirts between a bullnose rotating scoop and an open-helical screw that provides the rotations and material lift and evacuation. A conical working-face of the bullnose rotating scoop has symmetrically distributed graters and vents to break loose and force-in granular material from natural deposits and cargo holds. The bullnose rotating scoop and the open-helical screw its attached to move the material into a continuous layer on the inside surface of an outer stationary sheathing. A motor drive attached to the open-helical screw above at the delivery end provides the lifting force necessary.

Cool Down Experiences with the SST-1 Helium Cryogenics System before and after Current Feeders System Modification

NASA Astrophysics Data System (ADS)

Patel, R.; Panchal, P.; Panchal, R.; Tank, J.; Mahesuriya, G.; Sonara, D.; Srikanth, G. L. N.; Garg, A.; Bairagi, N.; Christian, D.; Patel, K.; Shah, P.; Nimavat, H.; Sharma, R.; Patel, J. C.; Gupta, N. C.; Prasad, U.; Sharma, A. N.; Tanna, V. L.; Pradhan, S.

The SST-1 machine comprises a superconducting magnet system (SCMS), which includes TF and PF magnets. In order to charge the SCMS, we need superconducting current feeders consisting of SC feeders and vapor cooled current leads (VCCLs). We have installed all 10 (+/-) pairs of VCCLs for the TF and PF systems. While conducting initial engineering validation of the SST-1 machine, our prime objective was to produce circular plasma using only the TF system. During the SST-1 campaign I to VI, we have to stop the PF magnets cooling in order to get the cryo- stable conditions for current charging of the TF magnets system. In that case, the cooling of the PF current leads is not essential. It has been also observed that after aborting the PF system cooling, there was a limited experimental window of TF operation. Therefore, in the recent SST-1 campaign-VII, we removed the PF current leads (9 pairs) and kept only single (+/-) pair of the 10,000 A rated VCCLs to realize the charging of the TF system for the extended window of operation. We have observed a better cryogenic stability in the TF magnets after modifications in the CFS. In this paper, we report the comparison of the cool down performance for the SST-1 machine operation before and after modifications of the current feeders system.

Evaluation of ERDA-sponsored coal feed system development

NASA Technical Reports Server (NTRS)

Phen, R. L.; Luckow, W. K.; Mattson, L.; Otth, D.; Tsou, P.

1977-01-01

Coal feeders were evaluated based upon criteria such as technical feasibility, performance (i.e. ability to meet process requirements), projected life cycle costs, and projected development cost. An initial set of feeders was selected based on the feeders' cost savings potential compared with baseline lockhopper systems. Additional feeders were considered for selection based on: (1) increasing the probability of successful feeder development; (2) application to specific processes; and (3) technical merit. A coal feeder development program is outlined.

Advanced Aircraft Electrical System Control Technology Demonstrator. Phase I. Requirements Analysis and Conceptual Design.

DTIC Science & Technology

1981-07-01

System 13 (7) Flight Critical Power 15 (8) Power Bus Configuration 16 b. System Control and Protection 20...includes the main buses, external power receptacles and distribution feeders. The function of the distribution protection system * is mainly to provide...TechnicaI rea Manager Power Systems Branch Power Systems B nch Aerospace Power Division Aerospace Power Division FOR .AKE D . REAMS Chief,

The effects of food web structure on ecosystem function exceeds those of precipitation.

PubMed

Trzcinski, M Kurtis; Srivastava, Diane S; Corbara, Bruno; Dézerald, Olivier; Leroy, Céline; Carrias, Jean-François; Dejean, Alain; Céréghino, Régis

2016-09-01

Ecosystems are being stressed by climate change, but few studies have tested food web responses to changes in precipitation patterns and the consequences to ecosystem function. Fewer still have considered whether results from one geographic region can be applied to other regions, given the degree of community change over large biogeographic gradients. We assembled, in one field site, three types of macroinvertebrate communities within water-filled bromeliads. Two represented food webs containing both a fast filter feeder-microbial and slow detritivore energy channels found in Costa Rica and Puerto Rico, and one represented the structurally simpler food webs in French Guiana, which only contained the fast filter feeder-microbial channel. We manipulated the amount and distribution of rain entering bromeliads and examined how food web structure mediated ecosystem responses to changes in the quantity and temporal distribution of precipitation. Food web structure affected the survival of functional groups in general and ecosystem functions such as decomposition and the production of fine particulate organic matter. Ecosystem processes were more affected by decreased precipitation than were the abundance of micro-organisms and metazoans. In our experiments, the sensitivity of the ecosystem to precipitation change was primarily revealed in the food web dominated by the single filter feeder-microbial channel because other top-down and bottom-up processes were weak or absent. Our results show stronger effects of food web structure than precipitation change per se on the functioning of bromeliad ecosystems. Consequently, we predict that ecosystem function in bromeliads throughout the Americas will be more sensitive to changes in the distribution of species, rather than to the direct effects caused by changes in precipitation. © 2016 The Authors. Journal of Animal Ecology © 2016 British Ecological Society.

New Capabilities in the Astrophysics Multispectral Archive Search Engine

NASA Astrophysics Data System (ADS)

Cheung, C. Y.; Kelley, S.; Roussopoulos, N.

The Astrophysics Multispectral Archive Search Engine (AMASE) uses object-oriented database techniques to provide a uniform multi-mission and multi-spectral interface to search for data in the distributed archives. We describe our experience of porting AMASE from Illustra object-relational DBMS to the Informix Universal Data Server. New capabilities and utilities have been developed, including a spatial datablade that supports Nearest Neighbor queries.

Colour preferences of UK garden birds at supplementary seed feeders.

PubMed

Rothery, Luke; Scott, Graham W; Morrell, Lesley J

2017-01-01

Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds.

Precision powder feeder

DOEpatents

Schlienger, M. Eric; Schmale, David T.; Oliver, Michael S.

2001-07-10

A new class of precision powder feeders is disclosed. These feeders provide a precision flow of a wide range of powdered materials, while remaining robust against jamming or damage. These feeders can be precisely controlled by feedback mechanisms.

Simulating Global AeroMACS Airport Ground Station Antenna Power Transmission Limits to Avoid Interference With Mobile Satellite Service Feeder Uplinks

NASA Technical Reports Server (NTRS)

Wilson, Jeffrey D.

2013-01-01

The Aeronautical Mobile Airport Communications System (AeroMACS), which is based upon the IEEE 802.16e mobile wireless standard, is expected to be implemented in the 5091 to 5150 MHz frequency band. As this band is also occupied by Mobile Satellite Service feeder uplinks, AeroMACS must be designed to avoid interference with this incumbent service. The aspects of AeroMACS operation that present potential interference are under analysis in order to enable the definition of standards that assure that such interference will be avoided. In this study, the cumulative interference power distribution at low Earth orbit from transmitters at global airports was simulated with the Visualyse Professional software. The dependence of the interference power on antenna distribution, gain patterns, duty cycle, and antenna tilt was simulated. As a function of these parameters, the simulation results are presented in terms of the limitations on transmitter power from global airports required to maintain the cumulative interference power under the established threshold.

Customer Engagement in AEP gridSMART Residential Transactive System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Widergren, Steven E.; Marinovici, Maria C.; Fuller, Jason C.

— In 2013, AEP Ohio (AEP) operated a 5-minute real-time price (RTP) electricity market system on 4 distribution feeders as part of their gridSMART® demonstration project. The RTP households were billed for their electricity usage according to an RTP tariff approved by the Public Utility Commission of Ohio. They were given the incentive that their annual bill would be no greater than if they were on the flat-rate tariff, but they had financial incentives to shift consumption from high price periods to low price periods. Incentives were also available for response under high prices from local events, such as reachingmore » the distribution feeder capacity or a critical peak pricing event. An analysis of this transactive system experiment was completed in early 2014. This paper describes the incentive provided to the customer, the nature of their interaction with the smart thermostat that provided automated response to the transactive signal, and their level of satisfaction with the program.« less

Mitigating energy loss on distribution lines through the allocation of reactors

NASA Astrophysics Data System (ADS)

Miranda, T. M.; Romero, F.; Meffe, A.; Castilho Neto, J.; Abe, L. F. T.; Corradi, F. E.

2018-03-01

This paper presents a methodology for automatic reactors allocation on medium voltage distribution lines to reduce energy loss. In Brazil, some feeders are distinguished by their long lengths and very low load, which results in a high influence of the capacitance of the line on the circuit’s performance, requiring compensation through the installation of reactors. The automatic allocation is accomplished using an optimization meta-heuristic called Global Neighbourhood Algorithm. Given a set of reactor models and a circuit, it outputs an optimal solution in terms of reduction of energy loss. The algorithm is also able to verify if the voltage limits determined by the user are not being violated, besides checking for energy quality. The methodology was implemented in a software tool, which can also show the allocation graphically. A simulation with four real feeders is presented in the paper. The obtained results were able to reduce the energy loss significantly, from 50.56%, in the worst case, to 93.10%, in the best case.

Meta-analysis on the effects of the physical environment, animal traits, feeder and feed characteristics on the feeding behaviour and performance of growing-finishing pigs.

PubMed

Averós, X; Brossard, L; Dourmad, J Y; de Greef, K H; Edwards, S A; Meunier-Salaün, M C

2012-08-01

A meta-analysis, using information from 45 experiments on growing-finishing pigs published in 39 manuscripts, was carried out to determine the simultaneous effects of the physical environment (space allowance, group size, flooring conditions, temperature, presence of enrichment), pig traits (initial body weight (BW) for each studied time interval, sex, genetics), feeder characteristics (water provision within the feeder, feeder design (individual/collective), feeder places/pig, presence of feeder protection) and feed characteristics (feed allowance (ad libitum/restricted), net energy content, crude protein (CP) content), as well as their potential interactions, on the feeding behaviour and performance of growing-finishing pigs. The detrimental effect of low temperature on performance was particularly evident for restricted-fed pigs (P < 0.05). At reduced feeder space allowance, a reduction in the percentage of time spent eating was predicted when increasing initial BW, whereas the opposite was predicted for larger feeder space allowances (P < 0.001). The reduction in visit duration to the feeder in higher BW groups became gradually more important with increasing feeder space allowance (P < 0.01), whereas the increase in the ingestion rate and average daily feed intake (ADFI) with increasing initial BW became smaller with increasing feeder space (P < 0.05). The model predicted a reduction in feed conversion ratio (FCR) with increasing group size (P < 0.05) and floor space allowance (P < 0.01) and on solid floors with or without bedding (P < 0.05). In comparison with other feeders, wet/dry feeders were associated with more frequent but shorter feeder visits (P < 0.05), higher ingestion rates (P < 0.001) and higher ADFI (P < 0.10). The use of protection within individual feeders increased the time spent feeding (P < 0.001), reduced the number of visits per day (P < 0.01), the ingestion rate (P < 0.001) and FCR (P < 0.01) in comparison with other feeder types. Sex modulated the effect of the number of feeder places/pig on FCR (P < 0.05), with a gradual reduction of FCR in entire males and females when increasing feeder space allowance. Genetics tended to modulate the effect of diets' CP content on FCR (P < 0.10). Overall, these results may contribute to the improvement of the welfare and performance of growing-finishing pigs by a better knowledge of the influence of the rearing environment and may help optimize the feeding strategies in current production systems.

Multi-objective optimization of radiotherapy: distributed Q-learning and agent-based simulation

NASA Astrophysics Data System (ADS)

Jalalimanesh, Ammar; Haghighi, Hamidreza Shahabi; Ahmadi, Abbas; Hejazian, Hossein; Soltani, Madjid

2017-09-01

Radiotherapy (RT) is among the regular techniques for the treatment of cancerous tumours. Many of cancer patients are treated by this manner. Treatment planning is the most important phase in RT and it plays a key role in therapy quality achievement. As the goal of RT is to irradiate the tumour with adequately high levels of radiation while sparing neighbouring healthy tissues as much as possible, it is a multi-objective problem naturally. In this study, we propose an agent-based model of vascular tumour growth and also effects of RT. Next, we use multi-objective distributed Q-learning algorithm to find Pareto-optimal solutions for calculating RT dynamic dose. We consider multiple objectives and each group of optimizer agents attempt to optimise one of them, iteratively. At the end of each iteration, agents compromise the solutions to shape the Pareto-front of multi-objective problem. We propose a new approach by defining three schemes of treatment planning created based on different combinations of our objectives namely invasive, conservative and moderate. In invasive scheme, we enforce killing cancer cells and pay less attention about irradiation effects on normal cells. In conservative scheme, we take more care of normal cells and try to destroy cancer cells in a less stressed manner. The moderate scheme stands in between. For implementation, each of these schemes is handled by one agent in MDQ-learning algorithm and the Pareto optimal solutions are discovered by the collaboration of agents. By applying this methodology, we could reach Pareto treatment plans through building different scenarios of tumour growth and RT. The proposed multi-objective optimisation algorithm generates robust solutions and finds the best treatment plan for different conditions.

How learning might strengthen existing visual object representations in human object-selective cortex.

PubMed

Brants, Marijke; Bulthé, Jessica; Daniels, Nicky; Wagemans, Johan; Op de Beeck, Hans P

2016-02-15

Visual object perception is an important function in primates which can be fine-tuned by experience, even in adults. Which factors determine the regions and the neurons that are modified by learning is still unclear. Recently, it was proposed that the exact cortical focus and distribution of learning effects might depend upon the pre-learning mapping of relevant functional properties and how this mapping determines the informativeness of neural units for the stimuli and the task to be learned. From this hypothesis we would expect that visual experience would strengthen the pre-learning distributed functional map of the relevant distinctive object properties. Here we present a first test of this prediction in twelve human subjects who were trained in object categorization and differentiation, preceded and followed by a functional magnetic resonance imaging session. Specifically, training increased the distributed multi-voxel pattern information for trained object distinctions in object-selective cortex, resulting in a generalization from pre-training multi-voxel activity patterns to after-training activity patterns. Simulations show that the increased selectivity combined with the inter-session generalization is consistent with a training-induced strengthening of a pre-existing selectivity map. No training-related neural changes were detected in other regions. In sum, training to categorize or individuate objects strengthened pre-existing representations in human object-selective cortex, providing a first indication that the neuroanatomical distribution of learning effects depends upon the pre-learning mapping of visual object properties. Copyright © 2015 Elsevier Inc. All rights reserved.

30 CFR 77.1802 - Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 77.1802 Section 77.1802... Wires and Trolley Feeder Wires § 77.1802 Insulation of trolley wires, trolley feeder wires and bare...

30 CFR 77.1802 - Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 77.1802 Section 77.1802... Wires and Trolley Feeder Wires § 77.1802 Insulation of trolley wires, trolley feeder wires and bare...

WaveJava: Wavelet-based network computing

NASA Astrophysics Data System (ADS)

Ma, Kun; Jiao, Licheng; Shi, Zhuoer

1997-04-01

Wavelet is a powerful theory, but its successful application still needs suitable programming tools. Java is a simple, object-oriented, distributed, interpreted, robust, secure, architecture-neutral, portable, high-performance, multi- threaded, dynamic language. This paper addresses the design and development of a cross-platform software environment for experimenting and applying wavelet theory. WaveJava, a wavelet class library designed by the object-orient programming, is developed to take advantage of the wavelets features, such as multi-resolution analysis and parallel processing in the networking computing. A new application architecture is designed for the net-wide distributed client-server environment. The data are transmitted with multi-resolution packets. At the distributed sites around the net, these data packets are done the matching or recognition processing in parallel. The results are fed back to determine the next operation. So, the more robust results can be arrived quickly. The WaveJava is easy to use and expand for special application. This paper gives a solution for the distributed fingerprint information processing system. It also fits for some other net-base multimedia information processing, such as network library, remote teaching and filmless picture archiving and communications.

PVUSA: The value of photovoltaics in the distribution system. The Kerman Grid-Support Project

NASA Astrophysics Data System (ADS)

Wenger, Howard J.; Hoff, Thomas E.

1995-05-01

As part of the Photovoltaics for Utility Scale Applications Applications (PVUSA) Project Pacific Gas Electric Company (PG&E) built the Kerman 500-kW photovoltaic power plant. Located near the end of a distribution feeder in a rural section of Fresno County, the plant was not built so much to demonstrate PV technology, but to evaluate its interaction with the local distribution grid and quantify available nontraditional grid-support benefits (those other than energy and capacity). As demand for new generation began to languish in the 1980s, and siting and permitting of power plants and transmission lines became more involved, utilities began considering smaller, distributed power sources. Potential benefits include shorter construction lead time, less capital outlay, and better utilization of existing assets. The results of a PG&E study in 1990/1991 of the benefits from a PV system to the distribution grid prompted the PVUSA Project to construct a plant at Kerman. Completed in 1993, the plant is believed to be the first one specifically built to evaluate the multiple benefits to the grid of a strategically sited plant. Each of nine discrete benefits were evaluated in detail by first establishing the technical impact, then translating the results into present economic value. Benefits span the entire system from distribution feeder to the generation fleet. This work breaks new ground in evaluation of distributed resources, and suggests that resource planning practices be expanded to account for these non-traditional benefits.

Feeder density enhances house finch disease transmission in experimental epidemics.

PubMed

Moyers, Sahnzi C; Adelman, James S; Farine, Damien R; Thomason, Courtney A; Hawley, Dana M

2018-05-05

Anthropogenic food provisioning of wildlife can alter the frequency of contacts among hosts and between hosts and environmental sources of pathogens. Despite the popularity of garden bird feeding, few studies have addressed how feeders influence host contact rates and disease dynamics. We experimentally manipulated feeder density in replicate aviaries containing captive, pathogen-naive, groups of house finches ( Haemorhous mexicanus ) and continuously tracked behaviours at feeders using radio-frequency identification devices. We then inoculated one bird per group with Mycoplasma gallisepticum (Mg), a common bacterial pathogen for which feeders are fomites of transmission, and assessed effects of feeder density on house finch behaviour and pathogen transmission. We found that pathogen transmission was significantly higher in groups with the highest density of bird feeders, despite a significantly lower rate of intraspecific aggressive interactions relative to the low feeder density groups. Conversely, among naive group members that never showed signs of disease, we saw significantly higher concentrations of Mg-specific antibodies in low feeder density groups, suggesting that birds in low feeder density treatments had exposure to subclinical doses of Mg. We discuss ways in which the density of garden bird feeders could play an important role in mediating the intensity of Mg epidemics.This article is part of the theme issue 'Anthropogenic resource subsidies and host-parasite dynamics in wildlife'. © 2018 The Author(s).

Feeding rates and under-ice foraging strategies of the smallest lunge filter feeder, the Antarctic minke whale (Balaenoptera bonaerensis).

PubMed

Friedlaender, A S; Goldbogen, J A; Nowacek, D P; Read, A J; Johnston, D; Gales, N

2014-08-15

Body size and feeding mode are two fundamental characteristics that determine foraging performance and ecological niche. As the smallest obligate lunge filter feeders, minke whales represent an ideal system for studying the physical and energetic limits of filter feeding in endotherms. We used multi-sensor suction cup tags to quantify the feeding performance of Antarctic minke whales. Foraging dives around and beneath sea ice contained up to 24 lunges per dive, the highest feeding rates for any lunge-feeding whale. Their small size allows minke whales access to krill in sea-ice environments not easily accessible to larger baleen whales. Furthermore, their ability to filter feed provides an advantage over other smaller sympatric krill predators such as penguins and seals that feed on individual prey. The unique combination of body size, feeding mechanism and sea-ice habitat of Antarctic minke whales defines a previously undocumented energetic niche that is unique among aquatic vertebrates. © 2014. Published by The Company of Biologists Ltd.

Evaluation of Potential Energy Loss Reduction and Savings for U. S. Army Electrical Distribution Systems

DTIC Science & Technology

1993-09-01

Different Size Transformers (Per Transformer ) 41 15 Additional Energy Losses for Mis-Sized Transformers (Per Transformer ) 42 16 Power System ...directly affects the amount of neutral line power loss in the system . Since most Army three-phase loads are distribution transformers spread out over a...61 Balancing Three-Phase Loads Balancing Feeder Circuit Loads Power Factor Correction Optimal Transformer Sizing Conductor Sizing Combined

Hawaiian Electric Advanced Inverter Test Plan - Result Summary

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoke, Anderson; Nelson, Austin; Prabakar, Kumaraguru

This presentation is intended to share the results of lab testing of five PV inverters with the Hawaiian Electric Companies and other stakeholders and interested parties. The tests included baseline testing of advanced inverter grid support functions, as well as distribution circuit-level tests to examine the impact of the PV inverters on simulated distribution feeders using power hardware-in-the-loop (PHIL) techniques. hardware-in-the-loop (PHIL) techniques.

Publications | Energy Systems Integration Facility | NREL

Science.gov Websites

100% Renewable Grid: Operating Electric Power Systems with Extremely High Levels of Variable Renewable timeline. Feeder Voltage Regulation with High-Penetration PV Using Advanced Inverters and a Distribution Integrating High Levels of Variable Renewable Energy into Electric Power Systems, Journal of Modern Power

Colour preferences of UK garden birds at supplementary seed feeders

PubMed Central

Rothery, Luke; Scott, Graham W.

2017-01-01

Supplementary feeding of garden birds generally has benefits for both bird populations and human wellbeing. Birds have excellent colour vision, and show preferences for food items of particular colours, but research into colour preferences associated with artificial feeders is limited to hummingbirds. Here, we investigated the colour preferences of common UK garden birds foraging at seed-dispensing artificial feeders containing identical food. We presented birds simultaneously with an array of eight differently coloured feeders, and recorded the number of visits made to each colour over 370 30-minute observation periods in the winter of 2014/15. In addition, we surveyed visitors to a garden centre and science festival to determine the colour preferences of likely purchasers of seed feeders. Our results suggest that silver and green feeders were visited by higher numbers of individuals of several common garden bird species, while red and yellow feeders received fewer visits. In contrast, people preferred red, yellow, blue and green feeders. We suggest that green feeders may be simultaneously marketable and attractive to foraging birds. PMID:28212435

Folivory or fruit/seed predation for Mesopithecus, an earliest colobine from the late Miocene of Eurasia?

PubMed

Merceron, Gildas; Scott, Jessica; Scott, Robert S; Geraads, Denis; Spassov, Nikolai; Ungar, Peter S

2009-12-01

Here we compare dental microwear textures from specimens of the fossil genus Mesopithecus (Cercopithecidae, Colobinae) from the late Miocene of Eastern Europe with dental microwear textures from four extant primate species with known dietary differences. Results indicate that the dental microwear textures of Mesopithecus differ from those of extant leaf eaters Alouatta palliata and Trachypithecus cristatus and instead resemble more closely those of the occasional hard-object feeders Cebus apella and Lophocebus albigena. Microwear texture data presented here in combination with results from previous analyses suggest that Mesopithecus was a widespread, opportunistic feeder that often consumed hard seeds. These data are consistent with the hypothesis that early colobines may have preferred hard seeds to leaves.

Sinks and sources: Assessing microplastic abundance in river sediment and deposit feeders in an Austral temperate urban river system.

PubMed

Nel, Holly A; Dalu, Tatenda; Wasserman, Ryan J

2018-01-15

Microplastics are important novel pollutants in freshwaters but their behaviour in river sediments is poorly understood due to the large amounts of coloured dissolved organic matter that impede sample processing. The present study aimed to 1.) estimate the microplastic pollution dynamics in an urban river system experiencing temporal differences in river flow, and 2.) investigate the potential use of chironomids as indicators of microplastic pollution levels in degraded freshwater environments. Microplastic levels were estimated from sediment and Chironomus spp. larvae collected from various sites along the Bloukrans River system, in the Eastern Cape South Africa during the summer and winter season. River flow, water depth, channel width, substrate embeddedness and sediment organic matter were simultaneously collected from each site. The winter season was characterised by elevated microplastic abundances, likely as a result of lower energy and increased sediment deposition associated with reduced river flow. In addition, results showed that particle distribution may be governed by various other external factors, such as substrate type and sediment organic matter. The study further highlighted that deposit feeders associated with the benthic river habitats, namely Chironomus spp. ingest microplastics and that the seasonal differences in sediment microplastic dynamics were reflected in chironomid microplastic abundance. There was a positive, though weakly significant relationship between deposit feeders and sediment suggesting that deposit feeders such as Chironomus spp. larvae could serve as an important indicator of microplastic loads within freshwater ecosystems. Copyright © 2017 Elsevier B.V. All rights reserved.

Distribution of free gas and 3D mirror image structures beneath Sevastopol mud volcano, Black sea, from 3D high resolution wide-angle seismic data

NASA Astrophysics Data System (ADS)

Krabbenhoeft, A.; Papenberg, C. A.; Klaeschen, D.; Bialas, J.

2016-12-01

The goal of this study is to image the sub-seafloor structure beneath the Sevastopol mud volcano (SMV), Sorokin Trough, SE of the Crimean peninsula, Black Sea. The focus lies on structures of/within the feeder channel, the distribution of gas and gas hydrates, and their relation to fluid migration zones in sediments. This study concentrates on a 3D high resolution seismic grid (7 km x 2.5 km) recorded with 13 ocean bottom stations (OBS). The 3D nature of the experiment results from the geometry of 68 densely spaced (25/50 m) profiles, as well as the cubical configuration of the densely spaced receivers on the seafloor ( 300 m station spacing). The seismic profiles are typically longer than 6 km which results in large offsets for the reflections of the OBS. This enables the study of the seismic velocities of the sub-seafloor sediments and additionally large offset incident analysis.The 3D Kirchhoff mirror image time migration, applied to all OBS sections including all shots from all profiles, leads to a spatial image of the sub-seafloor. Here, the migration was applied with the velocity distribution of 1.49 km/s in the water column, 1.5 km/s below the seafloor (bsf) increasing to 2 km/s for the deeper sediments at 2 s bsf. Acoustic blanking occurs beneath the south-easterly located OBS and is associated with the feeder channel of the mud volcano. There, gas from depth can vertically migrate to the seafloor and on its way to the surface horizontally distribute patchily within sediment layers. High amplitude reflections are not observed as continuous reflections, but in a patchy distribution. They are associated with accumulations of gas. Also structures exist within the feeder channel of the SMV.3D mirror imaging proves to be a good tool to seismically image structures compared with 2D streamer seismics, especially steep dipping reflectors and structures which are otherwise obscured by signal scattering, i.e structures associated with fluid migration paths.

35. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

35. INTERIOR VIEW, SAME AS ABOVE WITH THE FEEDER ROD INSERTED INTO THE MACHINE; NOTE THE WOOD FEEDER ROD AND FEEDER ROD REST ON THE BACK OF THE STOOL - LaBelle Iron Works, Thirtieth & Wood Streets, Wheeling, Ohio County, WV

[Optimal solution and analysis of muscular force during standing balance].

PubMed

Wang, Hongrui; Zheng, Hui; Liu, Kun

2015-02-01

The present study was aimed at the optimal solution of the main muscular force distribution in the lower extremity during standing balance of human. The movement musculoskeletal system of lower extremity was simplified to a physical model with 3 joints and 9 muscles. Then on the basis of this model, an optimum mathematical model was built up to solve the problem of redundant muscle forces. Particle swarm optimization (PSO) algorithm is used to calculate the single objective and multi-objective problem respectively. The numerical results indicated that the multi-objective optimization could be more reasonable to obtain the distribution and variation of the 9 muscular forces. Finally, the coordination of each muscle group during maintaining standing balance under the passive movement was qualitatively analyzed using the simulation results obtained.

29 CFR 1910.305 - Wiring methods, components, and equipment for general use.

Code of Federal Regulations, 2010 CFR

2010-07-01

... distribution center. (B) Conductors shall be run as multiconductor cord or cable assemblies. However, if... persons, feeders may be run as single insulated conductors. (v) The following requirements apply to branch... shall be multiconductor cord or cable assemblies or open conductors. If run as open conductors, they...

29 CFR 1910.305 - Wiring methods, components, and equipment for general use.

Code of Federal Regulations, 2011 CFR

2011-07-01

... distribution center. (B) Conductors shall be run as multiconductor cord or cable assemblies. However, if... persons, feeders may be run as single insulated conductors. (v) The following requirements apply to branch... shall be multiconductor cord or cable assemblies or open conductors. If run as open conductors, they...

29 CFR 1910.305 - Wiring methods, components, and equipment for general use.

Code of Federal Regulations, 2013 CFR

2013-07-01

... distribution center. (B) Conductors shall be run as multiconductor cord or cable assemblies. However, if... persons, feeders may be run as single insulated conductors. (v) The following requirements apply to branch... shall be multiconductor cord or cable assemblies or open conductors. If run as open conductors, they...

29 CFR 1910.305 - Wiring methods, components, and equipment for general use.

Code of Federal Regulations, 2014 CFR

2014-07-01

... distribution center. (B) Conductors shall be run as multiconductor cord or cable assemblies. However, if... persons, feeders may be run as single insulated conductors. (v) The following requirements apply to branch... shall be multiconductor cord or cable assemblies or open conductors. If run as open conductors, they...

29 CFR 1910.305 - Wiring methods, components, and equipment for general use.

Code of Federal Regulations, 2012 CFR

2012-07-01

... distribution center. (B) Conductors shall be run as multiconductor cord or cable assemblies. However, if... persons, feeders may be run as single insulated conductors. (v) The following requirements apply to branch... shall be multiconductor cord or cable assemblies or open conductors. If run as open conductors, they...

7 CFR 1280.201 - Establishment and membership.

Code of Federal Regulations, 2011 CFR

2011-01-01

... this section are met. Region 1 shall include the geographic area east of the Mississippi River, which... feeders appointed to the Board are not all located in one geographic region as established for producers...) Adjustment of membership. At least once every 5 years, the Board will review the geographical distribution of...

Dynamics of phytophagous insects and their pathogens in Alaskan boreal forests

Treesearch

Richard A. Werner; Kenneth F. Raffa; Barbara L. Illman

2006-01-01

Boreal forests support an array of insects, including phytophagous (plant-eating) insects, saprophagous (detritus-eating) insects, and their associated parasites, predators, and symbionts. The phytophagous species include folivorous leaf chewers and miners, phloeophagous cambial and sapwood borers, stem gallers, and root feeders. Biological diversity and distribution...

Educational Organization for Desegregation. Research Memorandum No. 4.

ERIC Educational Resources Information Center

Platt, William J.

As part of a series of reports dealing with racial distribution in San Francisco schools, this memorandum presents the rationale for adopting patterns of educational reorganization as an accompaniment to efforts to improve racial balance. Reasons are presented for adopting feeder patterns as students progress from the elementary to secondary…

A Feeder-Bus Dispatch Planning Model for Emergency Evacuation in Urban Rail Transit Corridors

PubMed Central

Wang, Yun; Yan, Xuedong; Zhou, Yu; Zhang, Wenyi

2016-01-01

The mobility of modern metropolises strongly relies on urban rail transit (URT) systems, and such a heavy dependence causes that even minor service interruptions would make the URT systems unsustainable. This study aims at optimally dispatching the ground feeder-bus to coordinate with the urban rails’ operation for eliminating the effect of unexpected service interruptions in URT corridors. A feeder-bus dispatch planning model was proposed for the collaborative optimization of URT and feeder-bus cooperation under emergency situations and minimizing the total evacuation cost of the feeder-buses. To solve the model, a concept of dummy feeder-bus system is proposed to transform the non-linear model into traditional linear programming (ILP) model, i.e., traditional transportation problem. The case study of Line #2 of Nanjing URT in China was adopted to illustrate the model application and sensitivity analyses of the key variables. The modeling results show that as the evacuation time window increases, the total evacuation cost as well as the number of dispatched feeder-buses decrease, and the dispatched feeder-buses need operate for more times along the feeder-bus line. The number of dispatched feeder-buses does not show an obvious change with the increase of parking spot capacity and time window, indicating that simply increasing the parking spot capacity would cause huge waste for the emergent bus utilization. When the unbalanced evacuation demand exists between stations, the more feeder-buses are needed. The method of this study will contribute to improving transportation emergency management and resource allocation for URT systems. PMID:27676179

Functional groupings and food web of an artificial reef used for sea cucumber aquaculture in northern China

NASA Astrophysics Data System (ADS)

Xu, Qinzeng; Zhang, Libin; Zhang, Tao; Zhang, Xuelei; Yang, Hongsheng

2017-01-01

Artificial reef is considered as a useful tool to remodel habitats in coastal and estuarine area. Some artificial reefs (ARs) were conducted in Shandong Peninsula for sea cucumber Apostichopus japonicus integrated multi-trophic aquaculture (IMTA). Little is known about the main feeding type and food resources of living organisms in this IMTA ecosystem. Neither is the information about other animals competing food with A. japonicus. Functional group (FG) and their food resources of mobile organisms and epifauna in ARs area were investigated. There were three types of food resources and five FGs within two trophic levels in studied area. Particle organic matter (POM), seaweed detritus and sediment were considered to be the main food resources. The first three FGs were primary consumers and were mainly epifauna, while the other two FGs were secondary consumers. FG 1 species were filter feeders, and group 2 was all deposit feeders and A. japonicus was in this group. FG 2 contained few species and this indicated that A. japonicus had few food competitors. FG 3 contained most epifauna species which were detritus feeders and this result implied that the artificial oyster shell reed can retain detritus effectively. The food sources of group 4 were complex. Species of group 5, mostly fish, occupied the top trophic level and fed primarily on species of FG 1 and FG 2. This kind of ARs can retain detritus effectively and provide suitable habitat to epifauna and surrounding natural fauna community.

Mercury Bioaccumulation in Tropical Mangrove Wetland Fishes: Evaluating Potential Risk to Coastal Wildlife.

PubMed

Le, Dung Quang; Satyanarayana, Behara; Fui, Siau Yin; Shirai, Kotaro

2018-03-26

The present study, aimed at observing the total concentration of mercury (Hg) in edible finfish species with an implication to human health risk, was carried out from the Setiu mangrove wetlands on the east coast of Peninsular Malaysia. Out of 20 species observed, the highest Hg concentrations were found among carnivores-fish/invertebrate-feeders, followed by omnivores and carnivores-invertebrate-feeders, while the lowest concentrations in herbivores. The Hg concentrations varied widely with fish species and body size, from 0.12 to 2.10 mg/kg dry weight. A positive relationship between body weight and Hg concentration was observed in particular for Toxotes jaculatrix and Tetraodon nigroviridis. Besides the permissible range of Hg concentration up to 0.3 mg/kg (cf. United States Environmental Protection Agency (USEPA)) in majority of species, the carnivore feeders such as Acanthopagrus pacificus, Gerres filamentosus, and Caranx ignobilis have shown excess amounts (> 0.40 mg/kg flesh weight) that raising concerns over the consumption by local people. However, the weekly intake of mercury-estimated through the fish consumption in all three trophic levels-suggests that the present Hg concentrations are still within the range of Provisional Tolerable Weekly Intake (PTWI) reported by the Joint FAO/WHO Expert Committee on Food Additives (JECFA). Perhaps, a multi-species design for Hg monitoring at Setiu wetlands would be able to provide further insights into the level of toxicity transfer among other aquatic organisms and thereby a strong health risk assessment for the local communities.

Influence of Powder Injection Parameters in High-Pressure Cold Spray

NASA Astrophysics Data System (ADS)

Ozdemir, Ozan C.; Widener, Christian A.

2017-10-01

High-pressure cold spray systems are becoming widely accepted for use in the structural repair of surface defects of expensive machinery parts used in industrial and military equipment. The deposition quality of cold spray repairs is typically validated using coupon testing and through destructive analysis of mock-ups or first articles for a defined set of parameters. In order to provide a reliable repair, it is important to not only maintain the same processing parameters, but also to have optimum fixed parameters, such as the particle injection location. This study is intended to provide insight into the sensitivity of the way that the powder is injected upstream of supersonic nozzles in high-pressure cold spray systems and the effects of variations in injection parameters on the nature of the powder particle kinetics. Experimentally validated three-dimensional computational fluid dynamics (3D CFD) models are implemented to study the particle impact conditions for varying powder feeder tube size, powder feeder tube axial misalignment, and radial powder feeder injection location on the particle velocity and the deposition shape of aluminum alloy 6061. Outputs of the models are statistically analyzed to explore the shape of the spray plume distribution and resulting coating buildup.

Trophodynamics of a deep-sea demersal fish assemblage from the bathyal eastern Ionian Sea (Mediterranean Sea)

NASA Astrophysics Data System (ADS)

Madurell, T.; Cartes, J. E.

2005-11-01

Daily food consumption of the eight dominant demersal fish species of the bathyal eastern Ionian Sea were determined from field data on four seasonal cruises (April 1999, July August 1999, November 1999 and February 2000). Daily ration (DR) estimates ranged from 0.198 to 4.273% WW/WW. Overall, DR estimates were independent of the model used, and they were comparable to the daily consumption of other deep-sea fauna (e.g. fish and crustaceans). Both sharks studied ( Galeus melastomus and Etmopterus spinax) exhibited the highest values of DRs, together with the macrourid Coelorhynchus coelorhynchus in August. Among osteichthyes, DR estimates were related (in a multi-linear regression model) to the nature of their diet (i.e. their trophic level deduced from δ15N isotopic composition, the mean number of prey and trophic diversity). Thus, species feeding at a lower trophic level, ingesting a large number of prey items and with a very diversified diet had higher DR than species from higher trophic level and feeding fewer prey items. By season, the DR of species feeding mainly on mesopelagic prey ( Hoplostethus mediterraneus and Helicolenus dactylopterus) were higher in summer, while DR for benthos/suprabenthos feeders (i.e. C. coelorhynchus and Nezumia sclerorhynchus) were higher in spring. Higher food consumption coincides with maximum food availability, both among mesopelagic feeders (higher availability of euphausiids, Pasiphaea sivado and Sergestes arcticus in summer) and among Macrouridae (higher suprabenthos densities in spring). In a tentative estimate the energy intake deduced from diet (i.e. mean energy value of food ingested) was constant in all seasons for each species studied. Results for the energy intake also indicate higher energy intake in the diet of mesopelagic feeders than in the diet of benthic feeders. Overall results are discussed in relation to the deep-sea ecosystem structure and functioning.

Analysis of material particle motion and optimizing parameters of vibration of two-mass GZS vibratory feeder

NASA Astrophysics Data System (ADS)

Nguyen, Van Xo; Golikov, N. S.

2018-05-01

The structure and kinematics of the two-mass GZS vibratory feeder operation are considered. It is established that the movement of the material's particles on the feeder surface determines its capacity. The development and analysis of the mathematical model of material's particle movement on the two-mass GZS vibratory feeder surface are shown. The results of Matlab optimization of material particles velocity function are given that allows setting rational kinematics of the feeder.

Multi-object segmentation using coupled nonparametric shape and relative pose priors

NASA Astrophysics Data System (ADS)

Uzunbas, Mustafa Gökhan; Soldea, Octavian; Çetin, Müjdat; Ünal, Gözde; Erçil, Aytül; Unay, Devrim; Ekin, Ahmet; Firat, Zeynep

2009-02-01

We present a new method for multi-object segmentation in a maximum a posteriori estimation framework. Our method is motivated by the observation that neighboring or coupling objects in images generate configurations and co-dependencies which could potentially aid in segmentation if properly exploited. Our approach employs coupled shape and inter-shape pose priors that are computed using training images in a nonparametric multi-variate kernel density estimation framework. The coupled shape prior is obtained by estimating the joint shape distribution of multiple objects and the inter-shape pose priors are modeled via standard moments. Based on such statistical models, we formulate an optimization problem for segmentation, which we solve by an algorithm based on active contours. Our technique provides significant improvements in the segmentation of weakly contrasted objects in a number of applications. In particular for medical image analysis, we use our method to extract brain Basal Ganglia structures, which are members of a complex multi-object system posing a challenging segmentation problem. We also apply our technique to the problem of handwritten character segmentation. Finally, we use our method to segment cars in urban scenes.

ITER Magnet Feeder: Design, Manufacturing and Integration

NASA Astrophysics Data System (ADS)

CHEN, Yonghua; ILIN, Y.; M., SU; C., NICHOLAS; BAUER, P.; JAROMIR, F.; LU, Kun; CHENG, Yong; SONG, Yuntao; LIU, Chen; HUANG, Xiongyi; ZHOU, Tingzhi; SHEN, Guang; WANG, Zhongwei; FENG, Hansheng; SHEN, Junsong

2015-03-01

The International Thermonuclear Experimental Reactor (ITER) feeder procurement is now well underway. The feeder design has been improved by the feeder teams at the ITER Organization (IO) and the Institute of Plasma Physics, Chinese Academy of Sciences (ASIPP) in the last 2 years along with analyses and qualification activities. The feeder design is being progressively finalized. In addition, the preparation of qualification and manufacturing are well scheduled at ASIPP. This paper mainly presents the design, the overview of manufacturing and the status of integration on the ITER magnet feeders. supported by the National Special Support for R&D on Science and Technology for ITER (Ministry of Public Security of the People's Republic of China-MPS) (No. 2008GB102000)

Spinal arteriovenous shunts: accuracy of shunt detection, localization, and subtype discrimination using spinal magnetic resonance angiography and manual contrast injection using a syringe.

PubMed

Unsrisong, Kittisak; Taphey, Siriporn; Oranratanachai, Kanokporn

2016-04-01

The object of this study was to evaluate the accuracy of fast 3D contrast-enhanced spinal MR angiography (MRA) using a manual syringe contrast injection technique for detecting and evaluating spinal arteriovenous shunts (AVSs). This was a retrospective study of 15 patients and 20 spinal MRA and catheter angiography studies. The accuracy of using spinal MRA to detect spinal AVS, localize shunts, and discriminate the subtype and dominant arterial feeder of the AVS were studied. There were 14 pretherapeutic and 6 posttherapeutic follow-up spinal MRA and catheter spinal angiography studies. The spinal AVS was demonstrated in 17 of 20 studies. Spinal MRA demonstrated 100% sensitivity for detecting spinal AVS with no false-negative results. A 97% accuracy rate for AVS subtype discrimination and shunt level localization was achieved using this study's diagnostic criteria. The detection of the dominant arterial feeder was limited to 9 of these 17 cases (53%). The fast 3D contrast-enhanced MRA technique performed using manual syringe contrast injection can detect the presence of a spinal AVS, locate the shunt level, and discriminate AVS subtype in most cases, but is limited when detecting small arterial feeders.

Research on vehicle routing optimization for the terminal distribution of B2C E-commerce firms

NASA Astrophysics Data System (ADS)

Zhang, Shiyun; Lu, Yapei; Li, Shasha

2018-05-01

In this paper, we established a half open multi-objective optimization model for the vehicle routing problem of B2C (business-to-customer) E-Commerce firms. To minimize the current transport distance as well as the disparity between the excepted shipments and the transport capacity in the next distribution, we applied the concept of dominated solution and Pareto solutions to the standard particle swarm optimization and proposed a MOPSO (multi-objective particle swarm optimization) algorithm to support the model. Besides, we also obtained the optimization solution of MOPSO algorithm based on data randomly generated through the system, which verified the validity of the model.

Dry coal feeder development program at Ingersoll-Rand Research, Incorporated. [for coal gasification systems

NASA Technical Reports Server (NTRS)

Mistry, D. K.; Chen, T. N.

1977-01-01

A dry coal screw feeder for feeding coal into coal gasification reactors operating at pressures up to 1500 psig is described. Results on the feeder under several different modes of operation are presented. In addition, three piston feeder concepts and their technical and economical merits are discussed.

Using supplemental food and its influence on survival of northern bobwhite (Colinus virginianus)

USGS Publications Warehouse

Townsend, D.E.; Lochmiller, R.L.; DeMaso, S.J.; Leslie, David M.; Peoples, A.D.; Scott, A C.; Parry, E.S.

2000-01-01

Biologists have debated the effectiveness of supplemental feeders as a management tool for the northern bobwhite (Colinus virginianus), but few extensive evaluations have been conducted. We examined 783 crops from harvested bobwhites during 1992-1996 to determine effects of climatic stress in winter on use of supplemental feeders and their impact on survival rate in winter. Crops of bobwhites harvested from areas with supplemental feeders contained 28.2% supplemental food compared with 5.5% (P<0.001) for those from areas without supplemental feeders. Winter climate was not a significant predictor of the proportional use of supplemental feeders. Rates of winter survival were greater on areas with supplemental feeders compared with non-supplemented areas in winters 1992-1993 (P=0.001) and 1993-1994 (P=0.002), but in 1994-1995, rates were greater on nonsupplemented areas (P=0.032). Cause-specific mortality rates indicated that supplemental feeders did not predispose bobwhites to hunter harvest or predators. Results suggested that bobwhites can gain nutritional benefits from supplemental feeders during times of severe winter stress.

An evaluation of the choice of feeder cell growth arrest for the production of cultured epidermis.

PubMed

Chugh, Rishi Man; Chaturvedi, Madhusudan; Yerneni, Lakshmana Kumar

2015-12-01

Growth arrested 3T3 cells have been used as feeder cells in human epidermal keratinocyte cultures to produce cultured epidermal autografts for the treatment of burns. The feeder cells were ideally growth-arrested by gamma-irradiation. Alternatively, growth arrest by mitomycin C treatment is a cost effective option. We compared the functional efficacy of these two approaches in keratinocyte cultures by colony forming efficiency, the net growth area of colonies, BrdU labeling and histological features of cultured epidermal sheets. The growth area estimation involved a semi-automated digital technique using the Adobe Photoshop and comprised of isolation and enumeration of red pixels in Rhodamine B-stained keratinocyte colonies. A further refinement of the technique led to the identification of critical steps to increasing the degree of accuracy and enabling its application as an extension of colony formation assay. The results on feeder cell functionality revealed that the gamma irradiated feeders influenced significantly higher colony forming efficiency and larger growth area than the mitomycin C treated feeders. The BrdU labeling study indicated significant stimulation of the overall keratinocyte proliferation by the gamma irradiated feeders. The cultured epidermal sheets produced by gamma feeders were relatively thicker than those produced by mitomycin C feeders. We discussed the clinical utility of mitomycin C feeders from the viewpoint of cost-effective burn care in developing countries. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Effects of different feeder layers on culture of bovine embryonic stem cell-like cells in vitro.

PubMed

Cong, Shan; Cao, Guifang; Liu, Dongjun

2014-12-01

To find a suitable feeder layer is important for successful culture conditions of bovine embryonic stem cell-like cells. In this study, expression of pluripotency-related genes OCT4, SOX2 and NANOG in bovine embryonic stem cell-like cells on mouse embryonic fibroblast feeder layers at 1-5 passages were monitored in order to identify the possible reason that bovine embryonic stem cell-like cells could not continue growth and passage. Here, we developed two novel feeder layers, mixed embryonic fibroblast feeder layers of mouse and bovine embryonic fibroblast at different ratios and sources including mouse fibroblast cell lines. The bovine embryonic stem cell-like cells generated in our study displayed typical stem cell morphology and expressed specific markers such as OCT4, stage-specific embryonic antigen 1 and 4, alkaline phosphatase, SOX2, and NANOG mRNA levels. When feeder layers and cell growth factors were removed, the bovine embryonic stem cell-like cells formed embryoid bodies in a suspension culture. Furthermore, we compared the expression of the pluripotent markers during bovine embryonic stem cell-like cell in culture on mixed embryonic fibroblast feeder layers, including mouse fibroblast cell lines feeder layers and mouse embryonic fibroblast feeder layers by real-time quantitative polymerase chain reaction. Results suggested that mixed embryonic fibroblast and sources including mouse fibroblast cell lines feeder layers were more suitable for long-term culture and growth of bovine embryonic stem cell-like cells than mouse embryonic fibroblast feeder layers. The findings may provide useful experimental data for the establishment of an appropriate culture system for bovine embryonic stem cell lines.

Developmental Competence of Buffalo (Bubalus bubalis) Pluripotent Embryonic Stem Cells Over Different Homologous Feeder Layers and the Comparative Evaluation with Various Extracellular Matrices.

PubMed

Sharma, Manjinder; Dubey, Pawan K; Kumar, Rajesh; Nath, Amar; Kumar, G Sai; Sharma, G Taru

2013-05-01

Use of somatic cells as a feeder layer to maintain the embryonic stem cells (ESCs) in undifferentiated state limits the stem cell research design, since experimental data may result from a combined ESCs and feeder cell response to various stimuli. Therefore, present study was designed to evaluate the developmental competence of the buffalo ESCs over different homogenous feeders and compare with various extracellular matrices using different concentrations of LIF. Inner cell masses (ICMs) of in vitro hatched blastocysts were cultured onto homologous feeders viz. fetal fibroblast, granulosa and oviductal cell feeder layers and synthetic matrices viz. fibronectin, collagen type I and matrigel in culture medium. Developmental efficiency was found higher for ESCs cultured on fetal fibroblast and granulosa layers (83.33%) followed by fibronectin (77.78%) at 30 ng LIF. Oviductal feeder was found to be the least efficient feeder showing only 11.11% undifferentiated primary ESC colonies at 30 ng LIF. However, neither feeder layer nor synthetic matrix could support the development of primary colonies at 10 ng LIF. Expression of SSEA- 4, TRA-1-60 and Oct-4 were found positive in ESC colonies from all the feeders and synthetic matrices with 20 ng and 30 ng LIF. Fetal fibroblast and granulosa cell while, amongst synthetic matrices, fibronectin were found to be equally efficient to support the growth and maintenance of ESCs pluripotency with 30 ng LIF. This well-defined culture conditions may provide an animal model for culturing human embryonic stem cells in the xeno-free or feeder-free conditions for future clinical applications.

Exclusion of broiler breeder females from male feeders with a male only grill. 1. Behavioral and technical aspects of design and development.

PubMed

Brake, J; Khamidullin, T N; Fisinin, V I

1993-03-01

A series of experiments was conducted in order to develop a feeder grill that would allow broiler breeder males, but not females, to eat. Females are typically excluded from male feeders by increasing the height of the feeder. However, male feeder heights that exclude most females increase the time required for males to consume a given amount of feed 19 to 60%. Typical male feeder height from floor to feeder pan lip in commercial practice is 55 cm, which is about the distance from floor to the head of the male in an erect posture. Females measure about 40 cm in an erect posture. Because the necks of males (8.0 cm) are longer than those of females (6.3 cm), the lip of male feeder pans was extended horizontally 12.7 cm with a wire mesh on the assumption that females could not stretch their necks enough to reach the feed. However, the females learned quickly to perch on the extended lip and eat. Total exclusion of females from the male feeder, regardless of feeder height, was achieved by placing a horizontal upper mesh 5.6 to 10.2 cm above the extended lip, and connecting the upper mesh to the lower extended lip of the feeder with vertical bars spaced 5.1 cm apart. The horizontal upper mesh prevented perching by females and the 5.1-cm spacing of the vertical bars allowed males but not females to reach the feed by inserting their heads and necks up to their shoulders.(ABSTRACT TRUNCATED AT 250 WORDS)

Gingival Fibroblasts as Autologous Feeders for Induced Pluripotent Stem Cells.

PubMed

Yu, G; Okawa, H; Okita, K; Kamano, Y; Wang, F; Saeki, M; Yatani, H; Egusa, H

2016-01-01

Human gingival fibroblasts (hGFs) present an attractive source of induced pluripotent stem cells (iPSCs), which are expected to be a powerful tool for regenerative dentistry. However, problems to be addressed prior to clinical application include the use of animal-derived feeder cells for cultures. The aim of this study was to establish an autologous hGF-derived iPSC (hGF-iPSC) culture system by evaluating the feeder ability of hGFs. In both serum-containing and serum-free media, hGFs showed higher proliferation than human dermal fibroblasts (hDFs). Three hGF strains were isolated under serum-free conditions, although 2 showed impaired proliferation. When hGF-iPSCs were transferred onto mitomycin C-inactivated hGFs, hDFs, or mouse-derived SNL feeders, hGF and SNL feeders were clearly hGF-iPSC supportive for more than 50 passages, whereas hDF feeders were only able to maintain undifferentiated hGF-iPSC growth for a few passages. After 20 passages on hGF feeders, embryonic stem cell marker expression and CpG methylation at the NANOG and OCT3/4 promoters were similar for hGF-iPSCs cultured on hGF and SNL feeder cells. Long-term cultures of hGF-iPSCs on hGF feeders sustained their normal karyotype and pluripotency. On hGF feeders, hGF-iPSC colonies were surrounded by many colony-derived fibroblast-like cells, and the size of intact colonies at 7 d after passage was significantly larger than that on SNL feeders. Allogeneic hGF strains also maintained hGF-iPSCs for 10 passages. Compared with hDFs, hGFs showed a higher production of laminin-332, laminin α5 chain, and insulin-like growth factor-II, which have been reported to sustain the long-term self-renewal of pluripotent stem cells. These results suggest that hGFs possess an excellent feeder capability and thus can be used as alternatives to conventional mouse-derived SNL and hDF feeders. In addition, our findings suggest that hGF feeders are promising candidates for animal component-free ex vivo expansion of autologous hGF-iPSCs, thus providing an important step toward the future therapeutic application of hGF-iPSCs. © International & American Associations for Dental Research 2015.

Serendipitous occultations by kilometer size Kuiper Belt with MIOSOTYS

NASA Astrophysics Data System (ADS)

Doressoundiram, A.; Liu, C.-Y.; Maquet, L.; Roques, F.

2017-09-01

MIOSOTYS (Multi-object Instrument for Occultations in the SOlar system and TransitorY Systems) is a multi-fiber positioner coupled with a fast photometry camera. This is a visitor instrument mounted on the 193 cm telescope at the Observatoire de Haute-Provence, France and on the 123 cm telescope at the Calar Alto Observatory, Spain. Our immediate goal is to characterize the spatial distribution and extension of the Kuiper Belt, and the physical size distribution of TNOs. We present the observation campaigns during 2010-2013, objectives and observing strategy. We report the detection of potential candidates for occultation events of TNOs. We will discuss more specifically the method used to process the data and the modelling of diffraction patterns. We, finally present the results obtained concerning the distribution of sub-kilometer TNOs in the Kuiper Belt.

Multi-camera digital image correlation method with distributed fields of view

NASA Astrophysics Data System (ADS)

Malowany, Krzysztof; Malesa, Marcin; Kowaluk, Tomasz; Kujawinska, Malgorzata

2017-11-01

A multi-camera digital image correlation (DIC) method and system for measurements of large engineering objects with distributed, non-overlapping areas of interest are described. The data obtained with individual 3D DIC systems are stitched by an algorithm which utilizes the positions of fiducial markers determined simultaneously by Stereo-DIC units and laser tracker. The proposed calibration method enables reliable determination of transformations between local (3D DIC) and global coordinate systems. The applicability of the method was proven during in-situ measurements of a hall made of arch-shaped (18 m span) self-supporting metal-plates. The proposed method is highly recommended for 3D measurements of shape and displacements of large and complex engineering objects made from multiple directions and it provides the suitable accuracy of data for further advanced structural integrity analysis of such objects.

Distribution Synergy in Multi-National Division-Baghdad during Operation Iraqi Freedom Rotation 07-09

DTIC Science & Technology

2011-06-10

customer wait time (CWT) in Multi-National Division-Baghdad (MND- B ) from October 2007 to January 2008. A secondary objective was to determine what...LIMITATION OF ABSTRACT 18. NUMBER OF PAGES 19a. NAME OF RESPONSIBLE PERSON a. REPORT b . ABSTRACT c. THIS PAGE 19b. PHONE NUMBER (include...Division-Baghdad (MND- B ) from October 2007 to January 2008. A secondary objective was to determine what affect initiatives from operational and

Concurrent Learning of Control in Multi agent Sequential Decision Tasks

DTIC Science & Technology

2018-04-17

Concurrent Learning of Control in Multi-agent Sequential Decision Tasks The overall objective of this project was to develop multi-agent reinforcement...learning (MARL) approaches for intelligent agents to autonomously learn distributed control policies in decentral- ized partially observable...shall be subject to any oenalty for failing to comply with a collection of information if it does not display a currently valid OMB control number

46 CFR 113.25-5 - Location of contact makers.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the navigating bridge; and (2) At the feeder distribution panel if the general alarm power supply is not in or next to the navigating bridge. (b) Tank vessels. Each tank vessel must have a manually operated contact maker for the general emergency alarm system: (1) In the navigating bridge; (2) At the...

46 CFR 113.25-5 - Location of contact makers.

Code of Federal Regulations, 2012 CFR

2012-10-01

... the navigating bridge; and (2) At the feeder distribution panel if the general alarm power supply is not in or next to the navigating bridge. (b) Tank vessels. Each tank vessel must have a manually operated contact maker for the general emergency alarm system: (1) In the navigating bridge; (2) At the...

46 CFR 113.25-5 - Location of contact makers.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the navigating bridge; and (2) At the feeder distribution panel if the general alarm power supply is not in or next to the navigating bridge. (b) Tank vessels. Each tank vessel must have a manually operated contact maker for the general emergency alarm system: (1) In the navigating bridge; (2) At the...

46 CFR 113.25-5 - Location of contact makers.

Code of Federal Regulations, 2013 CFR

2013-10-01

... the navigating bridge; and (2) At the feeder distribution panel if the general alarm power supply is not in or next to the navigating bridge. (b) Tank vessels. Each tank vessel must have a manually operated contact maker for the general emergency alarm system: (1) In the navigating bridge; (2) At the...

46 CFR 113.25-5 - Location of contact makers.

Code of Federal Regulations, 2011 CFR

2011-10-01

... the navigating bridge; and (2) At the feeder distribution panel if the general alarm power supply is not in or next to the navigating bridge. (b) Tank vessels. Each tank vessel must have a manually operated contact maker for the general emergency alarm system: (1) In the navigating bridge; (2) At the...

30 CFR 75.1003-1 - Other requirements for guarding of trolley wires and trolley feeder wires.

Code of Federal Regulations, 2010 CFR

2010-07-01

... wires and trolley feeder wires. 75.1003-1 Section 75.1003-1 Mineral Resources MINE SAFETY AND HEALTH... Trolley Wires and Trolley Feeder Wires § 75.1003-1 Other requirements for guarding of trolley wires and trolley feeder wires. Adequate precaution shall be taken to insure that equipment being moved along...

30 CFR 75.1003-1 - Other requirements for guarding of trolley wires and trolley feeder wires.

Code of Federal Regulations, 2011 CFR

2011-07-01

... wires and trolley feeder wires. 75.1003-1 Section 75.1003-1 Mineral Resources MINE SAFETY AND HEALTH... Trolley Wires and Trolley Feeder Wires § 75.1003-1 Other requirements for guarding of trolley wires and trolley feeder wires. Adequate precaution shall be taken to insure that equipment being moved along...

Negotiation, Administration, and Measurement of Food Service Contracts in Higher Education.

ERIC Educational Resources Information Center

Scott, H. Donald

1973-01-01

The process of establishing and maintaining relations with a contract feeder is reviewed. Initial contact, reasons for the contact, contract negotiation, key people involved, and the ultimate tools of measurement are mentioned. Possible goals and objectives to be specified to a negotiating contractor are suggested. Items to be covered in the…

Increased efficiency of gamma-irradiated versus mitomycin C-treated feeder cells for the expansion of normal human cells in long-term cultures.

PubMed

Roy, A; Krzykwa, E; Lemieux, R; Néron, S

2001-12-01

Several normal human cells, such as hematopoietic stem cells, dendritic cells, and B cells, can be cultured in vitro in defined optimal conditions. Several ex vivo culture systems require the use of feeder cells to support the growth of target cells. In such systems, proliferation of feeder cells has to be stopped, so that they can be used as nonreplicating viable support cells. Because feeder cells need to provide one or few active signals, it is important to maintain them in an metabolically active state, allowing continued expression of specific ligands or cytokines. Mitomycin C and gamma-irradiation treatments are commonly used to prepare nonproliferating feeder cells and are usually considered to be equivalent. Normal human B lymphocytes can be expanded in vitro in the presence of feeder cells expressing the CD40 ligand CD154. Here we compared the ability of gamma-irradiation- and mitomycin C-treated feeder cells to support the expansion of normal human B lymphocytes. The results indicate that expansion of B cells during a long-term culture was 100 times more potent using gamma-irradiated feeder cells compared to mitomycin C-treated cells. This difference could be related to a significant reduction in both cellular metabolism and level of CD154 expression observed in mitomycin C-treated feeder cells, but not in gamma-irradiated cells nor in control untreated cells. These results indicate that mitomycin C-treated feeder cells are metabolically altered, and consequently less efficient at maintaining cell expansion in the long-term cell culture system used.

A System-Level Throughput Model for Quantum Key Distribution

DTIC Science & Technology

2015-09-17

object. In quantum entanglement , the physical properties of particle pairs or groups of particles are correlated – the quantum state of each particle...One-Time Pad Algorithm ............................................................................. 8 Figure 2. Photon Polarization [19...64 Poisson distribution for multi- photon probability (29

Feeder & basic fibroblast growth factor-free culture of human embryonic stem cells: Role of conditioned medium from immortalized human feeders.

PubMed

Teotia, Pooja; Sharma, Shilpa; Airan, Balram; Mohanty, Sujata

2016-12-01

Human embryonic stem cell (hESC) lines are commonly maintained on inactivated feeder cells, in the medium supplemented with basic fibroblast growth factor (bFGF). However, limited availability of feeder cells in culture, and the high cost of growth factors limit their use in scalable expansion of hESC cultures for clinical application. Here, we describe an efficient and cost-effective feeder and bFGF-free culture of hESCs using conditioned medium (CM) from immortalized feeder cells. KIND-1 hESC cell line was cultured in CM, collected from primary mouse embryonic fibroblast, human foreskin fibroblast (HFF) and immortalized HFF (I-HFF). Pluripotency of KIND-1 hESC cell line was confirmed by expression of genes, proteins and cell surface markers. In culture, these cells retained normal morphology, expressed all cell surface markers, could differentiate to embryoid bodies upon culture in vitro. Furthermore, I-HFF feeder cells without supplementation of bFGF released ample amount of endogenous bFGF to maintain stemness of hESC cells. The study results described the use of CM from immortalized feeder cells as a consistent source and an efficient, inexpensive feeder-free culture system for the maintenance of hESCs. Moreover, it was possible to maintain hESCs without exogenous supplementation of bFGF. Thus, the study could be extended to scalable expansion of hESC cultures for therapeutic purposes.

Science capabilities of the Maunakea Spectroscopic Explorer

NASA Astrophysics Data System (ADS)

Devost, Daniel; McConnachie, Alan; Flagey, Nicolas; Cote, Patrick; Balogh, Michael; Driver, Simon P.; Venn, Kim

2017-01-01

The Maunakea Spectroscopic Explorer (MSE) project will transform the CFHT 3.6m optical telescope into a 10m class dedicated multiobject spectroscopic facility, with an ability to simultaneously measure thousands of objects with a spectral resolution range spanning 2,000 to 20,000. The project is currently in design phase, with full science operations nominally starting in 2025. MSE will enable transformational science in areas as diverse as exoplanetary host characterization; stellar monitoring campaigns; tomographic mapping of the interstellar and intergalactic media; the in-situ chemical tagging of the distant Galaxy; connecting galaxies to the large scale structure of the Universe; measuring the mass functions of cold dark matter sub-halos in galaxy and cluster-scale hosts; reverberation mapping of supermassive black holes in quasars. MSE is an essential follow-up facility to current and next generations of multi-wavelength imaging surveys, including LSST, Gaia, Euclid, eROSITA, SKA, and WFIRST, and is an ideal feeder facility for E-ELT, TMT and GMT. I will give an update on the status of the project and review some of the most exciting scientific capabilities of the observatory.

30 CFR 75.1003 - Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley...

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 75.1003 Section 75.1003... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1003...

30 CFR 75.1003 - Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley...

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 75.1003 Section 75.1003... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1003...

[Effects of prefrontal ablations on the reaction of the active choice of feeder under different probability and value of the reinforcement on dog].

PubMed

Preobrazhenskaia, L A; Ioffe, M E; Mats, V N

2004-01-01

The role of the prefrontal cortex was investigated on the reaction of the active choice of the two feeders under changes value and probability reinforcement. The experiments were performed on 2 dogs with prefrontal ablation (g. proreus). Before the lesions the dogs were taught to receive food in two different feeders to conditioned stimuli with equally probable alimentary reinforcement. After ablation in the inter-trial intervals the dogs were running from the one feeder to another. In the answer to conditioned stimuli for many times the dogs choose the same feeder. The disturbance of the behavior after some times completely restored. In the experiments with competition of probability events and values of reinforcement the dogs chose the feeder with low-probability but better quality of reinforcement. In the experiments with equal value but different probability the intact dogs chose the feeder with higher probability. In our experiments the dogs with prefrontal lesions chose the each feeder equiprobably. Thus in condition of free behavior one of different functions of the prefrontal cortex is the reactions choose with more probability of reinforcement.

Load allocation of power plant using multi echelon economic dispatch

NASA Astrophysics Data System (ADS)

Wahyuda, Santosa, Budi; Rusdiansyah, Ahmad

2017-11-01

In this paper, the allocation of power plant load which is usually done with a single echelon as in the load flow calculation, is expanded into a multi echelon. A plant load allocation model based on the integration of economic dispatch and multi-echelon problem is proposed. The resulting model is called as Single Objective Multi Echelon Economic Dispatch (SOME ED). This model allows the distribution of electrical power in more detail in the transmission and distribution substations along the existing network. Considering the interconnection system where the distance between the plant and the load center is usually far away, therefore the loss in this model is seen as a function of distance. The advantages of this model is its capability of allocating electrical loads properly, as well as economic dispatch information with the flexibility of electric power system as a result of using multi-echelon. In this model, the flexibility can be viewed from two sides, namely the supply and demand sides, so that the security of the power system is maintained. The model was tested on a small artificial data. The results demonstrated a good performance. It is still very open to further develop the model considering the integration with renewable energy, multi-objective with environmental issues and applied to the case with a larger scale.

Microplastics in the benthic invertebrates from the coastal waters of Kochi, Southeastern Arabian Sea.

PubMed

Naidu, S A; Ranga Rao, V; Ramu, K

2018-01-05

This study examined microplastic particles present in the benthic invertebrates Sternaspis scutata, Magelona cinta (deposit feeders) and Tellina sp. (suspension feeder) from the surface sediments of off-Kochi, southwest coast of India. The microplastic particles and thread-like fibres detected in these organisms were identified to be polystyrene by using DXR Raman microscope. Examination of the microplastic particle in Sternaspis scutata by epifluorescent microscopy showed fragmentation marks on the surface suggesting that the microplastic particle was degraded/weathered in nature. The study provides preliminary evidence of the presence of microplastics in benthic fauna from the coastal waters of India. However, further studies are required to understand the sources, distribution, fate and toxicity of the different types of microplastics in benthic invertebrates in order to identify any potential threats to higher trophic level organisms.

Volt-VAR Optimization on American Electric Power Feeders in Northeast Columbus

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schneider, Kevin P.; Weaver, T. F.

2012-05-10

In 2007 American Electric Power launched the gridSMART® initiative with the goals of increasing efficiency of the electricity delivery system and improving service to the end-use customers. As part of the initiative, a coordinated Volt-VAR system was deployed on eleven distribution feeders at five substations in the Northeast Columbus Ohio Area. The goal of the coordinated Volt-VAR system was to decrease the amount of energy necessary to provide end-use customers with the same quality of service. The evaluation of the Volt-VAR system performance was conducted in two stages. The first stage was composed of simulation, analysis, and estimation, while themore » second stage was composed of analyzing collected field data. This panel paper will examine the analysis conducted in both stages and present the estimated improvements in system efficiency.« less

Diversification of the silverspot butterflies (Nymphalidae) in the Neotropics inferred from multi-locus DNA sequences.

PubMed

Massardo, Darli; Fornel, Rodrigo; Kronforst, Marcus; Gonçalves, Gislene Lopes; Moreira, Gilson Rudinei Pires

2015-01-01

The tribe Heliconiini (Lepidoptera: Nymphalidae) is a diverse group of butterflies distributed throughout the Neotropics, which has been studied extensively, in particular the genus Heliconius. However, most of the other lineages, such as Dione, which are less diverse and considered basal within the group, have received little attention. Basic information, such as species limits and geographical distributions remain uncertain for this genus. Here we used multilocus DNA sequence data and the geographical distribution analysis across the entire range of Dione in the Neotropical region in order to make inferences on the evolutionary history of this poorly explored lineage. Bayesian time-tree reconstruction allows inferring two major diversification events in this tribe around 25mya. Lineages thought to be ancient, such as Dione and Agraulis, are as recent as Heliconius. Dione formed a monophyletic clade, sister to the genus Agraulis. Dione juno, D. glycera and D. moneta were reciprocally monophyletic and formed genetic clusters, with the first two more close related than each other in relation to the third. Divergence time estimates support the hypothesis that speciation in Dione coincided with both the rise of Passifloraceae (the host plants) and the uplift of the Andes. Since the sister species D. glycera and D. moneta are specialized feeders on passion-vine lineages that are endemic to areas located either within or adjacent to the Andes, we inferred that they co-speciated with their host plants during this vicariant event. Copyright © 2014 Elsevier Inc. All rights reserved.

Distributing Planning and Control for Teams of Cooperating Mobile Robots

DOE Office of Scientific and Technical Information (OSTI.GOV)

Parker, L.E.

2004-07-19

This CRADA project involved the cooperative research of investigators in ORNL's Center for Engineering Science Advanced Research (CESAR) with researchers at Caterpillar, Inc. The subject of the research was the development of cooperative control strategies for autonomous vehicles performing applications of interest to Caterpillar customers. The project involved three Phases of research, conducted over the time period of November 1998 through December 2001. This project led to the successful development of several technologies and demonstrations in realistic simulation that illustrated the effectiveness of our control approaches for distributed planning and cooperation in multi-robot teams. The primary objectives of this researchmore » project were to: (1) Develop autonomous control technologies to enable multiple vehicles to work together cooperatively, (2) Provide the foundational capabilities for a human operator to exercise oversight and guidance during the multi-vehicle task execution, and (3) Integrate these capabilities to the ALLIANCE-based autonomous control approach for multi-robot teams. These objectives have been successfully met with the results implemented and demonstrated in a near real-time multi-vehicle simulation of up to four vehicles performing mission-relevant tasks.« less

Effects of Feeder Cells on Dopaminergic Differentiation of Human Embryonic Stem Cells

PubMed Central

Zhao, Zhenqiang; Ma, Yanlin; Chen, Zhibin; Liu, Qian; Li, Qi; Kong, Deyan; Yuan, Kunxiong; Hu, Lan; Wang, Tan; Chen, Xiaowu; Peng, Yanan; Jiang, Weimin; Yu, Yanhong; Liu, Xinfeng

2016-01-01

Mouse embryonic fibroblasts (MEFs) and human foreskin fibroblasts (HFFs) are used for the culture of human embryonic stem cells (hESCs). MEFs and HFFs differed in their capacity to support the proliferation and pluripotency of hESCs and could affect cardiac differentiation potential of hESCs. The aim of this study was to evaluate the effect of MEFs and HFFs feeders on dopaminergic differentiation of hESCs lines. To minimize the impact of culture condition variation, two hESCs lines were cultured on mixed feeder cells (MFCs, MEFs: HFFs = 1:1) and HFFs feeder, respectively, and then were differentiated into dopaminergic (DA) neurons under the identical protocol. Dopaminergic differentiation was evaluated by immunocytochemistry, quantitative fluorescent real-time PCR, transmission and scanning electron microscopy, and patch clamp. Our results demonstrated that these hESCs-derived neurons were genuine and functional DA neurons. However, compared to hESCs line on MFCs feeder, hESCs line on HFFs feeder had a higher proportion of tyrosine hydroxylase (TH) positive cells and expressed higher levels of FOXA2, PITX3, NURR1, and TH genes. In addition, the values of threshold intensity and threshold membrane potential of DA neurons from hESCs line on HFFs feeder were lower than those of DA neurons from hESCs line on the MFCs feeder. In conclusion, HFFs feeder not only facilitated the differentiation of hESCs cells into dopaminergic neurons, but also induced hESCs-derived DA neurons to express higher electrophysiological excitability. Therefore, feeder cells could affect not only dopaminergic differentiation potential of different hESCs lines, but also electrophysiological properties of hESCs-derived DA neurons. PMID:28066186

Modeling and optimization of the multiobjective stochastic joint replenishment and delivery problem under supply chain environment.

PubMed

Wang, Lin; Qu, Hui; Liu, Shan; Dun, Cai-xia

2013-01-01

As a practical inventory and transportation problem, it is important to synthesize several objectives for the joint replenishment and delivery (JRD) decision. In this paper, a new multiobjective stochastic JRD (MSJRD) of the one-warehouse and n-retailer systems considering the balance of service level and total cost simultaneously is proposed. The goal of this problem is to decide the reasonable replenishment interval, safety stock factor, and traveling routing. Secondly, two approaches are designed to handle this complex multi-objective optimization problem. Linear programming (LP) approach converts the multi-objective to single objective, while a multi-objective evolution algorithm (MOEA) solves a multi-objective problem directly. Thirdly, three intelligent optimization algorithms, differential evolution algorithm (DE), hybrid DE (HDE), and genetic algorithm (GA), are utilized in LP-based and MOEA-based approaches. Results of the MSJRD with LP-based and MOEA-based approaches are compared by a contrastive numerical example. To analyses the nondominated solution of MOEA, a metric is also used to measure the distribution of the last generation solution. Results show that HDE outperforms DE and GA whenever LP or MOEA is adopted.

Modeling and Optimization of the Multiobjective Stochastic Joint Replenishment and Delivery Problem under Supply Chain Environment

PubMed Central

Dun, Cai-xia

2013-01-01

As a practical inventory and transportation problem, it is important to synthesize several objectives for the joint replenishment and delivery (JRD) decision. In this paper, a new multiobjective stochastic JRD (MSJRD) of the one-warehouse and n-retailer systems considering the balance of service level and total cost simultaneously is proposed. The goal of this problem is to decide the reasonable replenishment interval, safety stock factor, and traveling routing. Secondly, two approaches are designed to handle this complex multi-objective optimization problem. Linear programming (LP) approach converts the multi-objective to single objective, while a multi-objective evolution algorithm (MOEA) solves a multi-objective problem directly. Thirdly, three intelligent optimization algorithms, differential evolution algorithm (DE), hybrid DE (HDE), and genetic algorithm (GA), are utilized in LP-based and MOEA-based approaches. Results of the MSJRD with LP-based and MOEA-based approaches are compared by a contrastive numerical example. To analyses the nondominated solution of MOEA, a metric is also used to measure the distribution of the last generation solution. Results show that HDE outperforms DE and GA whenever LP or MOEA is adopted. PMID:24302880

Botanical compound p-anisaldehyde repels larval lone star tick, Amblyomma americanum (L.) (Acari: Ixodidae), and halts reproduction by gravid adults

USDA-ARS?s Scientific Manuscript database

The lone star tick, Amblyomma americanum (L.), widely distributed across eastern, southeastern, and midwestern regions of the United States and south into Mexico, is an obligate blood feeder that attaches to three hosts during the larval, nymphal, and adult stages. White-tailed deer and wild turkey ...

Comparison of defined culture systems for feeder cell free propagation of human embryonic stem cells

PubMed Central

Akopian, Veronika; Beil, Stephen; Benvenisty, Nissim; Brehm, Jennifer; Christie, Megan; Ford, Angela; Fox, Victoria; Gokhale, Paul J.; Healy, Lyn; Holm, Frida; Hovatta, Outi; Knowles, Barbara B.; Ludwig, Tenneille E.; McKay, Ronald D. G.; Miyazaki, Takamichi; Nakatsuji, Norio; Oh, Steve K. W.; Pera, Martin F.; Rossant, Janet; Stacey, Glyn N.; Suemori, Hirofumi

2010-01-01

There are many reports of defined culture systems for the propagation of human embryonic stem cells in the absence of feeder cell support, but no previous study has undertaken a multi-laboratory comparison of these diverse methodologies. In this study, five separate laboratories, each with experience in human embryonic stem cell culture, used a panel of ten embryonic stem cell lines (including WA09 as an index cell line common to all laboratories) to assess eight cell culture methods, with propagation in the presence of Knockout Serum Replacer, FGF-2, and mouse embryonic fibroblast feeder cell layers serving as a positive control. The cultures were assessed for up to ten passages for attachment, death, and differentiated morphology by phase contrast microscopy, for growth by serial cell counts, and for maintenance of stem cell surface marker expression by flow cytometry. Of the eight culture systems, only the control and those based on two commercial media, mTeSR1 and STEMPRO, supported maintenance of most cell lines for ten passages. Cultures grown in the remaining media failed before this point due to lack of attachment, cell death, or overt cell differentiation. Possible explanations for relative success of the commercial formulations in this study, and the lack of success with other formulations from academic groups compared to previously published results, include: the complex combination of growth factors present in the commercial preparations; improved development, manufacture, and quality control in the commercial products; differences in epigenetic adaptation to culture in vitro between different ES cell lines grown in different laboratories. PMID:20186512

Reduction of tablet weight variability by optimizing paddle speed in the forced feeder of a high-speed rotary tablet press.

PubMed

Peeters, Elisabeth; De Beer, Thomas; Vervaet, Chris; Remon, Jean-Paul

2015-04-01

Tableting is a complex process due to the large number of process parameters that can be varied. Knowledge and understanding of the influence of these parameters on the final product quality is of great importance for the industry, allowing economic efficiency and parametric release. The aim of this study was to investigate the influence of paddle speeds and fill depth at different tableting speeds on the weight and weight variability of tablets. Two excipients possessing different flow behavior, microcrystalline cellulose (MCC) and dibasic calcium phosphate dihydrate (DCP), were selected as model powders. Tablets were manufactured via a high-speed rotary tablet press using design of experiments (DoE). During each experiment also the volume of powder in the forced feeder was measured. Analysis of the DoE revealed that paddle speeds are of minor importance for tablet weight but significantly affect volume of powder inside the feeder in case of powders with excellent flowability (DCP). The opposite effect of paddle speed was observed for fairly flowing powders (MCC). Tableting speed played a role in weight and weight variability, whereas changing fill depth exclusively influenced tablet weight. The DoE approach allowed predicting the optimum combination of process parameters leading to minimum tablet weight variability. Monte Carlo simulations allowed assessing the probability to exceed the acceptable response limits if factor settings were varied around their optimum. This multi-dimensional combination and interaction of input variables leading to response criteria with acceptable probability reflected the design space.

Fearful Foragers: Honey Bees Tune Colony and Individual Foraging to Multi-Predator Presence and Food Quality

PubMed Central

Tan, Ken; Hu, Zongwen; Chen, Weiwen; Wang, Zhengwei; Wang, Yuchong; Nieh, James C.

2013-01-01

Fear can have strong ecosystem effects by giving predators a role disproportionate to their actual kill rates. In bees, fear is shown through foragers avoiding dangerous food sites, thereby reducing the fitness of pollinated plants. However, it remains unclear how fear affects pollinators in a complex natural scenario involving multiple predator species and different patch qualities. We studied hornets, Vespa velutina (smaller) and V. tropica (bigger) preying upon the Asian honey bee, Apis cerana in China. Hornets hunted bees on flowers and were attacked by bee colonies. Bees treated the bigger hornet species (which is 4 fold more massive) as more dangerous. It received 4.5 fold more attackers than the smaller hornet species. We tested bee responses to a three-feeder array with different hornet species and varying resource qualities. When all feeders offered 30% sucrose solution (w/w), colony foraging allocation, individual visits, and individual patch residence times were reduced according to the degree of danger. Predator presence reduced foraging visits by 55–79% and residence times by 17–33%. When feeders offered different reward levels (15%, 30%, or 45% sucrose), colony and individual foraging favored higher sugar concentrations. However, when balancing food quality against multiple threats (sweeter food corresponding to higher danger), colonies exhibited greater fear than individuals. Colonies decreased foraging at low and high danger patches. Individuals exhibited less fear and only decreased visits to the high danger patch. Contrasting individual with emergent colony-level effects of fear can thus illuminate how predators shape pollination by social bees. PMID:24098734

Backtest and novelty behavior of female and castrated male piglets, with diverging social breeding values for growth.

PubMed

Reimert, I; Rodenburg, T B; Ursinus, W W; Duijvesteijn, N; Camerlink, I; Kemp, B; Bolhuis, J E

2013-10-01

Pigs housed together in a group influence each other's growth. Part of this effect is genetic and can be represented in a social breeding value. It is unknown, however, which traits are associated with social breeding values. The aim of this study was, therefore, to investigate whether personality and response to novelty could be associated with social breeding values for growth in piglets. Female and castrated male piglets from 80 litters, with either an estimated relative positive or negative social breeding value (+SBV or -SBV) for growth, were individually tested in a backtest and novel environment test, and group-wise in a novel object (i.e., a feeder with feed) test and human approach test. All tests were performed during the suckling period. No differences between +SBV and -SBV piglets were found for the frequency and latency of struggling and vocalizing in the backtest (at least, P > 0.30). In the novel object test, piglets with a +SBV for growth touched the feeder faster than piglets with -SBV for growth (P = 0.01) and were more frequently present near the person in the human approach test (P < 0.01). No behavioral differences between +SBV and -SBV piglets were found in the novel environment test (at least, P > 0.40), but piglets that struggled more in the backtest walked more in this test (P = 0.02). Behavior was affected by gender in each test. Female piglets were faster than castrated male piglets to start struggling in the backtest (P = 0.047). In the novel object test, females were faster than males to touch the feeder and sample the feed. In the human approach test, they were also faster than male piglets to touch a person (all, P < 0.001). Females were also more frequently present near the feeder (P < 0.001) and person (P = 0.03). In the novel environment test, female piglets explored the floor more (P = 0.046), produced less low- (P = 0.04) and high-pitched vocalizations (P = 0.02), and defecated (P = 0.08) and urinated less than male piglets (P < 0.01). It was concluded that +SBV and -SBV piglets do not differ in their response to the backtest, and only subtle differences were found in their response to novelty. More research is warranted to identify the traits underlying SBV for growth in pigs. Moreover, castrated male piglets seemed to react more fearfully to each test than female piglets.

A Batch Feeder for Inhomogeneous Bulk Materials

NASA Astrophysics Data System (ADS)

Vislov, I. S.; Kladiev, S. N.; Slobodyan, S. M.; Bogdan, A. M.

2016-04-01

The work includes the mechanical analysis of mechanical feeders and batchers that find application in various technological processes and industrial fields. Feeders are usually classified according to their design features into two groups: conveyor-type feeders and non-conveyor feeders. Batchers are used to batch solid bulk materials. Less frequently, they are used for liquids. In terms of a batching method, they are divided into volumetric and weighting batchers. Weighting batchers do not provide for sufficient batching accuracy. Automatic weighting batchers include a mass controlling sensor and systems for automatic material feed and automatic mass discharge control. In terms of operating principle, batchers are divided into gravitational batchers and batchers with forced feed of material using conveyors and pumps. Improved consumption of raw materials, decreased loss of materials, ease of use in automatic control systems of industrial facilities allows increasing the quality of technological processes and improve labor conditions. The batch feeder suggested by the authors is a volumetric batcher that has no comparable counterparts among conveyor-type feeders and allows solving the problem of targeted feeding of bulk material batches increasing reliability and hermeticity of the device.

Pharmacokinetics and pharmacodynamics of gamithromycin in pulmonary epithelial lining fluid in naturally occurring bovine respiratory disease in multisource commingled feedlot cattle

USDA-ARS?s Scientific Manuscript database

The overall objectives of this study were to determine if a correlation exists between individual pharmacokinetic parameters and treatment outcome when feeder cattle were diagnosed with bovine respiratory disease (BRD) and treated with gamithromycin (Zactran®) at the label dose, and if there was a s...

A tangent-ring optical TWDM-MAN enabling three-level transregional reconfigurations and shared protections by multipoint distributed control

NASA Astrophysics Data System (ADS)

Gou, Kaiyu; Gan, Chaoqin; Zhang, Xiaoyu; Zhang, Yuchao

2018-03-01

An optical time-and-wavelength-division-multiplexing metro-access network (TWDM-MAN) is proposed and demonstrated in this paper. By the reuse of tangent-ring optical distribution network and the design of distributed control mechanism, ONUs needing to communicate with each other can be flexibly accessed to successfully make up three kinds of reconfigurable networks. By the nature advantage of ring topology in protection, three-level comprehensive protections covering both feeder and distribution fibers are also achieved. Besides, a distributed wavelength allocation (DWA) is designed to support efficient parallel upstream transmission. The analyses including capacity, congestion and transmission simulation show that this network has a great performance.

Developing the snow component of a distributed hydrological model: a step-wise approach based on multi-objective analysis

NASA Astrophysics Data System (ADS)

Dunn, S. M.; Colohan, R. J. E.

1999-09-01

A snow component has been developed for the distributed hydrological model, DIY, using an approach that sequentially evaluates the behaviour of different functions as they are implemented in the model. The evaluation is performed using multi-objective functions to ensure that the internal structure of the model is correct. The development of the model, using a sub-catchment in the Cairngorm Mountains in Scotland, demonstrated that the degree-day model can be enhanced for hydroclimatic conditions typical of those found in Scotland, without increasing meteorological data requirements. An important element of the snow model is a function to account for wind re-distribution. This causes large accumulations of snow in small pockets, which are shown to be important in sustaining baseflows in the rivers during the late spring and early summer, long after the snowpack has melted from the bulk of the catchment. The importance of the wind function would not have been identified using a single objective function of total streamflow to evaluate the model behaviour.

Shared Ride Taxi Feeder Service in Memphis, TN

DOT National Transportation Integrated Search

1988-03-01

From May 1983 through October 1984, the Memphis Area Transit Authority (MATA) conducted the Taxi Feeder Demonstration Project. It entailed the operation of fixed-route feeder services through three low-density neighborhoods and one industrial park, c...

Derivation of Human Skin Fibroblast Lines for Feeder Cells of Human Embryonic Stem Cells.

PubMed

Unger, Christian; Felldin, Ulrika; Rodin, Sergey; Nordenskjöld, Agneta; Dilber, Sirac; Hovatta, Outi

2016-02-03

After the first derivations of human embryonic stem cell (hESC) lines on fetal mouse feeder cell layers, the idea of using human cells instead of mouse cells as feeder cells soon arose. Mouse cells bear a risk of microbial contamination, and nonhuman immunogenic proteins are absorbed from the feeders to hESCs. Human skin fibroblasts can be effectively used as feeder cells for hESCs. The same primary cell line, which can be safely used for up to 15 passages after stock preparations, can be expanded and used for large numbers of hESC derivations and cultures. These cells are relatively easy to handle and maintain. No animal facilities or animal work is needed. Here, we describe the derivation, culture, and cryopreservation procedures for research-grade human skin fibroblast lines. We also describe how to make feeder layers for hESCs using these fibroblasts. Copyright © 2016 John Wiley & Sons, Inc.

Transmissible Gastroenteritis in Feeder Pigs: Observations on the Jejunal Epithelium of Normal Feeder Pigs and Feeder Pigs Infected with TGE Virus

PubMed Central

Morin, M.; Morehouse, L. G.

1974-01-01

Light and electron microscopy findings in the jejunal mucosa of the normal feeder pig and feeder pigs infected with transmissible gastroenteritis (TGE) virus are reported. Villi in the mid jejunum of the normal feeder pig were elongated, finger shaped and covered with a layer of columnar absorptive cells with a well developed and regular brush border. Severe lesions of villous atrophy were present in all jejunal segments of feeder swine killed 96 hours post infection with TGE virus. Atrophic villi were covered by flat to cuboidal cells with a poorly developed brush border in some areas. In other segments, cells varied in appearance from sub-columnar to columnar type of near normal appearance. The ultrastructure of the jejunal absorptive cells in the normal feeder pig was found to be similar to that described for the jejunal cells of other adult mammals. There were no significant indications of high pinocytotic activity. The epithelial cells covering the atrophic villi of TGE infected pigs had a fine structure similar to that described for the crypt cells, ranging in appearance from very immature to moderately differentiated cells. Microvilli were very short, decreased markedly in number and irregular in arrangement. The terminal web was poorly developed. Strands of rough endoplasmic reticulum were markedly diminished and an increase in free ribosomes was noted. The significance of these observations in explaining pathogenesis of TGE in feeder pigs is discussed. ImagesFig. 1.Fig. 2.Fig. 3.Fig. 4.Fig. 5.Fig. 6.Fig. 7.Fig. 8. PMID:4277743

39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

39. CLOSE UP DETAIL OF THE FEEDER AND STAMP CONNECTION. THE STAMP AN MORTAR BOX ARE ON THE LEFT AND THE FEEDER WITH ITS FEEDER DISK IS ON THE RIGHT. NOTE THE COLLAR ON THE CENTER STAMP STEM (UPPER LEFT CORNER OF THE IMAGE) THAT ACTIVATES THE LEVER IN THE CENTER OF THE PHOTO. THE COLLAR IS POSITIONED SUCH THAT WHEN THE LEVEL OF THE MATERIAL REACHES A LOW POINT IN THE MORTAR BOX IT PUSHES DOWN ON THE LEVER WHICH IN TURN ACTIVATES THE AUTOMATIC FEEDER DRIVE MECHANISM WHICH THEM DELIVERS ORE INTO THE BACKSIDE OF THE MORTAR BOX. - Standard Gold Mill, East of Bodie Creek, Northeast of Bodie, Bodie, Mono County, CA

A pellet feeder for the birds

PubMed Central

Millard, W. J.

1979-01-01

An alternative means of delivering food to pigeons in operant conditioning research is described. The feeder allows greater control of the amount of food delivered and reduces the amount of time necessary for the pigeon to collect the food. It is possible to extend the length of experimental sessions due to the reduction of food intake. Data obtained using the pellet feeder indicated that the control of responding is comparable to that observed with the standard grain-magazine feeder. PMID:16812118

Extending Human Hematopoietic Stem Cell Survival In Vitro with Adipocytes

PubMed Central

Glettig, Dean Liang

2013-01-01

Abstract Human hematopoietic stem cells (hHSCs) cannot be maintained in vitro for extended time periods because they rapidly differentiate or die. To extend in vitro culture time, researchers have made attempts to use human mesenchymal stem cells (hMSCs) to create feeder layers that mimic the stem cell niche. We have conducted an array of experiments including adipocytes in these feeder layers that inhibit hHSC differentiation and by that prolong stem cell survival in vitro. The amount of CD34+ cells was quantified using flow cytometry. In a first experiment, feeder layers of undifferentiated hMSCs were compared with feeder layers differentiated toward osteoblasts or adipocytes using minimal medium, showing the highest survival rate where adipocytes were included. The same conclusion was drawn in a second experiment in comparing hMSCs with adipogenic feeder cells, using a culture medium supplemented with a cocktail of hHSC growth factors. In a third experiment, it was shown that direct cell–cell contact is necessary for the supportive effect of the feeder layers. In a fourth and fifth experiment the amount of adipocytes in the feeder layers were varied, and in all experiments a higher amount of adipocytes in the feeder layers showed a less rapid decay of CD34+ cells at later time points. We therefore concluded that adipocytes assist in suppressing hHSC differentiation and aid in prolonging their survival in vitro. PMID:23741628

Microscopic suspension feeders near boundaries: Effects of external water flow

NASA Astrophysics Data System (ADS)

Pepper, Rachel; Koehl, M. A. R.

2015-11-01

Microscopic sessile suspension feeders are an important part of aquatic ecosystems and form a vital link in the transfer of carbon in aquatic food webs. These suspension feeders live attached to boundaries, consume bacteria and small detritus, and are in turn eaten by larger organisms. Many create a feeding current that draws fluid towards them, and from which they filter their food. In still water, the feeding current consists of recirculating eddies which form as a result of fluid forcing near a boundary. These recirculating eddies can be depleted of food and significantly decrease nutrient uptake; a variety of strategies have been proposed for how attached feeders increase their access to undepleted water. We investigate the interaction of the flow produced by a microscopic suspension feeder with external environmental flow, such as the current in a stream or ocean. We show through calculations that even very slow flow (on the order of microns per second) is sufficient to provide a constant supply of undepleted water to suspension feeders when the feeders are modeled with perfect nutrient capture efficiency and in the absence of diffusion. We also discuss which natural flow environments exceed the threshold to supply undepleted water and which do not, and we examine how characteristics of the suspension feeders themselves, such as stalk length and feeding disk size, influence feeding currents and their interactions with external flows.

Preliminary Assessment of Optimal Longitudinal-Mode Control for Drag Reduction through Distributed Aeroelastic Shaping

NASA Technical Reports Server (NTRS)

Ippolito, Corey; Nguyen, Nhan; Lohn, Jason; Dolan, John

2014-01-01

The emergence of advanced lightweight materials is resulting in a new generation of lighter, flexible, more-efficient airframes that are enabling concepts for active aeroelastic wing-shape control to achieve greater flight efficiency and increased safety margins. These elastically shaped aircraft concepts require non-traditional methods for large-scale multi-objective flight control that simultaneously seek to gain aerodynamic efficiency in terms of drag reduction while performing traditional command-tracking tasks as part of a complete guidance and navigation solution. This paper presents results from a preliminary study of a notional multi-objective control law for an aeroelastic flexible-wing aircraft controlled through distributed continuous leading and trailing edge control surface actuators. This preliminary study develops and analyzes a multi-objective control law derived from optimal linear quadratic methods on a longitudinal vehicle dynamics model with coupled aeroelastic dynamics. The controller tracks commanded attack-angle while minimizing drag and controlling wing twist and bend. This paper presents an overview of the elastic aircraft concept, outlines the coupled vehicle model, presents the preliminary control law formulation and implementation, presents results from simulation, provides analysis, and concludes by identifying possible future areas for research

10th European Zebrafish Meeting 2017, Budapest: Husbandry Workshop Summary.

PubMed

Oltová, Jana; Barton, Carrie; Certal, Ana Catarina; Argenton, Francesco; Varga, Zoltán M

2018-01-02

A husbandry workshop on July 3, 2017, at the 10th European Zebrafish Meeting in Budapest, Hungary (July 3-July 7, 2017), focused on the standardization, optimization, and streamlining of fish facility procedures. Standardization can be achieved for example by developing novel software and hardware tools, such as a fish facility database for husbandry and environmental facility management (Zebrabase, Oltova), or a hand-held, air-pressurized fish feeder for consistent food distribution (Blowfish, Argenton). Streamlining is achieved when work hours are reduced, as with the standardized fish feeder, or by limiting the number and types of fish diets and observing the effect on animal welfare and performance (Barton). Testing the characteristics of new fish diets and observing whether they produce better experimental outcomes (Certal) optimizes diets and improves fish productivity. Collectively, the workshop presentations emphasized how consistency and harmonization of husbandry procedures within and across aquatic facilities yield reproducible scientific outcomes.

Information Measures of Degree Distributions with an Application to Labeled Graphs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joslyn, Cliff A.; Purvine, Emilie AH

2016-01-11

The problem of describing the distribution of labels over a set of objects is relevant to many domains. For example: cyber security, social media, and protein interactions all care about the manner in which labels are distributed among different objects. In this paper we present three interacting statistical measures on label distributions, inspired by entropy and information theory. Labeled graphs are discussed as a specific case of labels distributed over a set of edges. We describe a use case in cyber security using a labeled directed multi-graph of IPFLOW. Finally we show how these measures respond when labels are updatedmore » in certain ways.« less

Trace-Forward Investigation of Mice in Response to Lymphocytic Choriomeningitis Virus Outbreak

PubMed Central

Knust, Barbara; Petersen, Bret; Gabel, Julie; Manning, Craig; Drenzek, Cherie; Ströher, Ute; Rollin, Pierre E.; Thoroughman, Douglas; Nichol, Stuart T.

2014-01-01

During follow-up of a 2012 US outbreak of lymphocytic choriomeningitis virus (LCMV), we conducted a trace-forward investigation. LCMV-infected feeder mice originating from a US rodent breeding facility had been distributed to >500 locations in 21 states. All mice from the facility were euthanized, and no additional persons tested positive for LCMV infection. PMID:24447898

Examining System-Wide Impacts of Solar PV Control Systems with a Power Hardware-in-the-Loop Platform

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, Tess L.; Fuller, Jason C.; Schneider, Kevin P.

2014-10-11

High penetration levels of distributed solar PV power generation can lead to adverse power quality impacts such as excessive voltage rise, voltage flicker, and reactive power values that result in unacceptable voltage levels. Advanced inverter control schemes have been proposed that have the potential to mitigate many power quality concerns. However, closed-loop control may lead to unintended behavior in deployed systems as complex interactions can occur between numerous operating devices. In order to enable the study of the performance of advanced control schemes in a detailed distribution system environment, a Hardware-in-the-Loop (HIL) platform has been developed. In the HIL system,more » GridLAB-D, a distribution system simulation tool, runs in real-time mode at the Pacific Northwest National Laboratory (PNNL) and supplies power system parameters at a point of common coupling to hardware located at the National Renewable Energy Laboratory (NREL). Hardware inverters interact with grid and PV simulators emulating an operational distribution system and power output from the inverters is measured and sent to PNNL to update the real-time distribution system simulation. The platform is described and initial test cases are presented. The platform is used to study the system-wide impacts and the interactions of controls applied to inverters that are integrated into a simulation of the IEEE 8500-node test feeder, with inverters in either constant power factor control or active volt/VAR control. We demonstrate that this HIL platform is well-suited to the study of advanced inverter controls and their impacts on the power quality of a distribution feeder. Additionally, the results from HIL are used to validate GridLAB-D simulations of advanced inverter controls.« less

Flow accelerated corrosion of carbon steel feeder pipes from pressurized heavy water reactors

NASA Astrophysics Data System (ADS)

Singh, J. L.; Kumar, Umesh; Kumawat, N.; Kumar, Sunil; Kain, Vivekanand; Anantharaman, S.; Sinha, A. K.

2012-10-01

Detailed investigation of a number of feeder pipes received from Rajasthan Atomic Power Station Unit 2 (RAPS#2) after en-masse feeder pipe replacement after 15.67 Effective Full Power Years (EFPYs) was carried out. Investigations included ultrasonic thickness measurement by ultrasonic testing, optical microscopy, scanning electron microscopy, chemical analysis and X-ray Diffraction (XRD). Results showed that maximum thickness reduction of the feeder had occurred downstream and close to the weld in 32 NB (1.25″/32.75 mm ID) elbows. Rate of Flow Accelerated Corrosion (FAC) was measured to be higher in the lower diameter feeder pipes due to high flow velocity and turbulence. Weld regions had thinned to a lower extent than the parent material due to higher chromium content in the weld. A weld protrusion has been shown to add to the thinning due to FAC and lead to faster thinning rate at localized regions. Surface morphology of inner surface of feeder had shown different size scallop pattern over the weld and parent material. Inter-granular cracks were also observed along the weld fusion line and in the parent material in 32 NB outlet feeder elbow.

Rapid fabricating technique for multi-layered human hepatic cell sheets by forceful contraction of the fibroblast monolayer.

PubMed

Sakai, Yusuke; Koike, Makiko; Hasegawa, Hideko; Yamanouchi, Kosho; Soyama, Akihiko; Takatsuki, Mitsuhisa; Kuroki, Tamotsu; Ohashi, Kazuo; Okano, Teruo; Eguchi, Susumu

2013-01-01

Cell sheet engineering is attracting attention from investigators in various fields, from basic research scientists to clinicians focused on regenerative medicine. However, hepatocytes have a limited proliferation potential in vitro, and it generally takes a several days to form a sheet morphology and multi-layered sheets. We herein report our rapid and efficient technique for generating multi-layered human hepatic cell (HepaRG® cell) sheets using pre-cultured fibroblast monolayers derived from human skin (TIG-118 cells) as a feeder layer on a temperature-responsive culture dish. Multi-layered TIG-118/HepaRG cell sheets with a thick morphology were harvested on day 4 of culturing HepaRG cells by forceful contraction of the TIG-118 cells, and the resulting sheet could be easily handled. In addition, the human albumin and alpha 1-antitrypsin synthesis activities of TIG-118/HepaRG cells were approximately 1.2 and 1.3 times higher than those of HepaRG cells, respectively. Therefore, this technique is considered to be a promising modality for rapidly fabricating multi-layered human hepatocyte sheets from cells with limited proliferation potential, and the engineered cell sheet could be used for cell transplantation with highly specific functions.

7 CFR 1280.107 - Feeder.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE LAMB PROMOTION, RESEARCH, AND INFORMATION ORDER Lamb Promotion, Research, and Information Order Definitions § 1280.107 Feeder. Feeder means any person who acquires ownership of lambs and feeds such lambs in the U.S. until they reach slaughter...

On Market-Based Coordination of Thermostatically Controlled Loads With User Preference

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Sen; Zhang, Wei; Lian, Jianming

2014-12-15

This paper presents a market-based control framework to coordinate a group of autonomous Thermostatically Controlled Loads (TCL) to achieve the system-level objectives with pricing incentives. The problem is formulated as maximizing the social welfare subject to feeder power constraint. It allows the coordinator to affect the aggregated power of a group of dynamical systems, and creates an interactive market where the users and the coordinator cooperatively determine the optimal energy allocation and energy price. The optimal pricing strategy is derived, which maximizes social welfare while respecting the feeder power constraint. The bidding strategy is also designed to compute the optimalmore » price in real time (e.g., every 5 minutes) based on local device information. The coordination framework is validated with realistic simulations in GridLab-D. Extensive simulation results demonstrate that the proposed approach effectively maximizes the social welfare and decreases power congestion at key times.« less

Aflatoxin contamination in corn sold for wildlife feed in texas.

PubMed

Dunham, Nicholas R; Peper, Steven T; Downing, Carson D; Kendall, Ronald J

2017-05-01

Supplemental feeding with corn to attract and manage deer is a common practice throughout Texas. Other species, including northern bobwhites (Colinus virginianus), are commonly seen feeding around supplemental deer feeders. In many cases, supplemental feeding continues year-round so feed supply stores always have supplemental corn in stock. Fluctuating weather and improper storage of corn can lead to and/or amplify aflatoxin contamination. Due to the recent decline of bobwhites throughout the Rolling Plains ecoregion of Texas, there has been interest in finding factors such as toxins that could be linked to their decline. In this study, we purchased and sampled supplemental corn from 19 locations throughout this ecoregion to determine if aflatoxin contamination was present in individual bags prior to being dispersed to wildlife. Of the 57 bags sampled, 33 bags (approximately 58%) contained aflatoxin with a bag range between 0.0-19.91 parts per billion (ppb). Additionally, three metal and three polypropylene supplemental feeders were each filled with 45.4 kg of triple cleaned corn and placed in an open field to study long-term aflatoxin buildup. Feeders were sampled every 3 months from November 2013-November 2014. Average concentration of aflatoxin over the year was 4.08 ± 2.53 ppb (±SE) in metal feeders, and 1.43 ± 0.89 ppb (±SE) in polypropylene feeders. The concentration of aflatoxins is not affected by the type of feeder (metal vs polypropylene), the season corn was sampled, and the location in the feeder (top, middle, bottom) where corn is sampled. It is unlikely that corn used in supplemental feeders is contributing to the bobwhite decline due to the low levels of aflatoxin found in purchased corn and long-term storage of corn used in supplemental feeders.

Diatom feeding across trophic guilds in tidal flat nematodes, and the importance of diatom cell size

NASA Astrophysics Data System (ADS)

Moens, Tom; Vafeiadou, Anna-Maria; De Geyter, Ellen; Vanormelingen, Pieter; Sabbe, Koen; De Troch, Marleen

2014-09-01

We examine the capacity of nematodes from three feeding types (deposit feeder, epistrate feeder, predator) to utilize microphytobenthos (MPB), and assess whether diatom cell size and consumer body size are important drivers of their feeding. We analyzed natural stable isotope ratios of carbon and nitrogen in abundant nematode genera and a variety of carbon sources at an estuarine intertidal flat. All nematodes had δ13C indicating that MPB is their major carbon source. δ15N, however, demonstrated that only one deposit and one epistrate feeder genus obtained most of their carbon from direct grazing on MPB, whereas other deposit feeders and predators obtained at least part of their carbon by predation on MPB grazers. We then performed a microcosm experiment in which equal cell numbers of each of three differently sized strains of the pennate diatom Seminavis were offered as food to four, one and one genera of deposit feeders, epistrate feeders and predators, respectively. Previous studies have shown that all but the epistrate feeder ingest whole diatoms, whereas the epistrate feeder pierces cells and sucks out their contents. Most genera showed markedly higher carbon absorption from medium and large cells than from small ones. When considering the number of cells consumed, however, none of the nematodes which ingest whole cells exhibited a clear preference for any specific diatom size. The epistrate feeder was the smallest nematode taxon considered here, yet it showed a marked preference for large cells. These results highlight that the feeding mechanism is much more important than consumer size as a driver of particle size selection in nematodes grazing MPB.

Vertical linear feeder to elliptical igneous saucer-shaped sills: evidences from structural observations, geochemistry and experimental modeling

NASA Astrophysics Data System (ADS)

Galerne, C. Y.; Galland, O.; Neumann, E. R.; Planke, S.

2009-12-01

The structural relationships between sills and their feeders are poorly documented because they are rarely observed in the field and difficult to image on seismic data. For instance, it is unclear whether sills are fed by pipes, dikes or other sills. Nevertheless, the geometrical relationships between sills and their feeders provide first-order constraints on magma emplacement mechanisms. Here, we investigate the structural and geochemical relationships between sills and potential feeder dikes in a remarkably well-preserved and exposed sill complex, the Golden Valley Sill Complex (GVSC), Karoo Basin, South Africa. The GVSC consists of five major saucer-shaped sills and six dikes. The Golden Valley sill itself is an elliptical saucer, with a N-S trend. A one meter thick dike (D4) crops out underneath the southern tip of the Golden Valley sill. The strike of this dike is parallel to the long axis of the Golden Valley sill. Detailed sampling and geochemical analyses of the GVSC show that each sill and dike exhibits a specific geochemical signature. The Golden Valley sill and its underlying dike D4 have identical signatures. Although there is no clear structural evidence, the consistent geometrical and geochemical relationships between the Golden Valley sill and the D4 dike suggest that this vertical linear structure is the feeder of the overlying saucer-shaped sill. In order to investigate the relationships between sills and feeders, we resorted to scaled laboratory experiments. The experiments consisted of a low-viscosity vegetable oil representing magma and a cohesive fine-grained silica flour representing brittle rocks. We placed a horizontal weak layer into the silica flour, just above the top of the inlet, to simulate strata. Such a weak layer controlled the formation of horizontal sill that subsequently turned into a transgressive sheet leading to the formation of a saucer geometry. We ran experiments with varying inlet shapes: 1) a point inlet representing a pipe-like feeder and 2) a linear feeder representing a dike-like feeder. In the experiments with point inlet, circular saucer-shaped sills formed. In the experiments with linear feeder, elliptical saucer-shaped sills formed. In the latter experiments, the long axes of the saucers were parallel to, and located directly above, the linear feeder. The experiments show that the feeder geometry has an important influence on the geometry of the emplaced sills. There are close similarities between the geometry of the Golden Valley sill and the intrusions formed in the experiments. The elliptical shape of the Golden Valley sill suggests that it was fed by an elongated feeder, probably the D4 dike. In general, our results show that the three-dimensional geometry of saucer-shaped sills observed in sedimentary basins, may constrain the shape of their feeders, i.e. their emplacement mechanisms.

Documentation of the data analysis system for the gamma ray monitor aboard OSO-H

NASA Technical Reports Server (NTRS)

Croteau, S.; Buck, A.; Higbie, P.; Kantauskis, J.; Foss, S.; Chupp, D.; Forrest, D. J.; Suri, A.; Gleske, I.

1973-01-01

The programming system is presented which was developed to prepare the data from the gamma ray monitor on OSO-7 for scientific analysis. The detector, data, and objectives are described in detail. Programs presented include; FEEDER, PASS-1, CAL1, CAL2, PASS-3, Van Allen Belt Predict Program, Computation Center Plot Routine, and Response Function Programs.

Feeder Voltage Regulation with High-Penetration PV Using Advanced Inverters and a Distribution Management System: A Duke Energy Case Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Palmintier, Bryan; Giraldez, Julieta; Gruchalla, Kenny

2016-11-01

Duke Energy, Alstom Grid, and the National Renewable Energy Laboratory teamed up to better understand the impacts of solar photovoltaics (PV) on distribution system operations. The core goal of the project is to compare the operational - specifically, voltage regulation - impacts of three classes of PV inverter operations: 1.) Active power only (Baseline); 2.) Local inverter control (e.g., PF...not equal...1, Q(V), etc.); and 3.) Integrated volt-VAR control (centralized through the distribution management system). These comparisons were made using multiple approaches, each of which represents an important research-and-development effort on its own: a) Quasi-steady-state time-series modeling for approximately 1 yearmore » of operations using the Alstom eTerra (DOTS) system as a simulation engine, augmented by Python scripting for scenario and time-series control and using external models for an advanced inverter; b) Power-hardware-in-the-loop (PHIL) testing of a 500-kVA-class advanced inverter and traditional voltage regulating equipment. This PHIL testing used cosimulation to link full-scale feeder simulation using DOTS in real time to hardware testing; c) Advanced visualization to provide improved insights into time-series results and other PV operational impacts; and d) Cost-benefit analysis to compare the financial and business-model impacts of each integration approach.« less

Economic feeder for recharging and ``topping off''

NASA Astrophysics Data System (ADS)

Fickett, Bryan; Mihalik, G.

2000-04-01

Increasing the size of the melt charge significantly increases yield and reduces costs. Siemens Solar Industries is optimizing a method to charge additional material after meltdown (top-off) using an external feeder system. A prototype feeder system was fabricated consisting of a hopper and feed delivery system. The low-cost feeder is designed for simple operation and maintenance. The system is capable of introducing up to 60 kg of granular silicon while under vacuum. An isolation valve permits refilling of the hopper while maintaining vacuum in the growth furnace. Using the feeder system in conjunction with Siemens Solar Industries' energy efficient hot zone dramatically reduces power and argon consumption. Throughput is also improved as faster pull speeds can be attained. The increased pull speeds have an even greater impact when the charge size is increased. Further cost reduction can be achieved by refilling the crucible after crystal growth and pulling a second ingot run. Siemens Solar Industries is presently testing the feeder in production.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chamana, Manohar; Prabakar, Kumaraguru; Palmintier, Bryan

A software process is developed to convert distribution network models from a quasi-static time-series tool (OpenDSS) to a real-time dynamic phasor simulator (ePHASORSIM). The description of this process in this paper would be helpful for researchers who intend to perform similar conversions. The converter could be utilized directly by users of real-time simulators who intend to perform software-in-the-loop or hardware-in-the-loop tests on large distribution test feeders for a range of use cases, including testing functions of advanced distribution management systems against a simulated distribution system. In the future, the developers intend to release the conversion tool as open source tomore » enable use by others.« less

Design optimization of axial flow hydraulic turbine runner: Part II - multi-objective constrained optimization method

NASA Astrophysics Data System (ADS)

Peng, Guoyi; Cao, Shuliang; Ishizuka, Masaru; Hayama, Shinji

2002-06-01

This paper is concerned with the design optimization of axial flow hydraulic turbine runner blade geometry. In order to obtain a better design plan with good performance, a new comprehensive performance optimization procedure has been presented by combining a multi-variable multi-objective constrained optimization model with a Q3D inverse computation and a performance prediction procedure. With careful analysis of the inverse design of axial hydraulic turbine runner, the total hydraulic loss and the cavitation coefficient are taken as optimization objectives and a comprehensive objective function is defined using the weight factors. Parameters of a newly proposed blade bound circulation distribution function and parameters describing positions of blade leading and training edges in the meridional flow passage are taken as optimization variables.The optimization procedure has been applied to the design optimization of a Kaplan runner with specific speed of 440 kW. Numerical results show that the performance of designed runner is successfully improved through optimization computation. The optimization model is found to be validated and it has the feature of good convergence. With the multi-objective optimization model, it is possible to control the performance of designed runner by adjusting the value of weight factors defining the comprehensive objective function. Copyright

Load flow and state estimation algorithms for three-phase unbalanced power distribution systems

NASA Astrophysics Data System (ADS)

Madvesh, Chiranjeevi

Distribution load flow and state estimation are two important functions in distribution energy management systems (DEMS) and advanced distribution automation (ADA) systems. Distribution load flow analysis is a tool which helps to analyze the status of a power distribution system under steady-state operating conditions. In this research, an effective and comprehensive load flow algorithm is developed to extensively incorporate the distribution system components. Distribution system state estimation is a mathematical procedure which aims to estimate the operating states of a power distribution system by utilizing the information collected from available measurement devices in real-time. An efficient and computationally effective state estimation algorithm adapting the weighted-least-squares (WLS) method has been developed in this research. Both the developed algorithms are tested on different IEEE test-feeders and the results obtained are justified.

An RFID Based Smart Feeder for Hummingbirds.

PubMed

Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F; Tang, Wei

2015-12-16

We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9-11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future.

An RFID Based Smart Feeder for Hummingbirds

PubMed Central

Ibarra, Vicente; Araya-Salas, Marcelo; Tang, Yu-ping; Park, Charlie; Hyde, Anthony; Wright, Timothy F.; Tang, Wei

2015-01-01

We present an interdisciplinary effort to record feeding behaviors and control the diet of a hummingbird species (Phaethornis longirostris, the long-billed hermit or LBH) by developing a Radio Frequency Identification (RFID) based smart feeder. The system contains an RFID reader, a microcontroller, and a servo-controlled hummingbird feeder opener; the system is presented as a tool for studying the cognitive ability of the LBH species. When equipped with glass capsule RFID tags (which are mounted on the hummingbird), the smart feeder can provide specific diets for predetermined sets of hummingbirds at the discretion of biologists. This is done by reading the unique RFID tag on the hummingbirds and comparing the ID number with the pre-programmed ID numbers stored in the smart feeder. The smart feeder records the time and ID of each hummingbird visit. The system data is stored in a readily available SD card and is powered by two 9 V batteries. The detection range of the system is approximately 9–11 cm. Using this system, biologists can assign the wild hummingbirds to different experimental groups and monitor their diets to determine if they develop a preference to any of the available nectars. During field testing, the smart feeder system has demonstrated consistent detection (when compared to detections observed by video-recordings) of RFID tags on hummingbirds and provides pre-designed nectars varying water and sugar concentrations to target individuals. The smart feeder can be applied to other biological and environmental studies in the future. PMID:26694402

Utilization of human amniotic mesenchymal cells as feeder layers to sustain propagation of human embryonic stem cells in the undifferentiated state.

PubMed

Zhang, Kehua; Cai, Zhe; Li, Yang; Shu, Jun; Pan, Lin; Wan, Fang; Li, Hong; Huang, Xiaojie; He, Chun; Liu, Yanqiu; Cui, Xiaohui; Xu, Yang; Gao, Yan; Wu, Liqun; Cao, Shanxia; Li, Lingsong

2011-08-01

Human embryonic stem (ES) cells are usually maintained in the undifferentiated state by culturing on feeder cells layers of mouse embryonic fibroblasts (MEFs). However, MEFs are not suitable to support human ES cells used for clinical purpose because of risk of zoonosis from animal cells. Therefore, human tissue-based feeder layers need to be developed for human ES cells for clinical purpose. Hereof we report that human amniotic mesenchymal cells (hAMCs) could act as feeder cells for human ES cells, because they are easily obtained and relatively exempt from ethical problem. Like MEFs, hAMCs could act as feeder cells for human ES cells to grow well on. The self-renewal rate of human ES cells cultured on hAMCs feeders was higher than that on MEFs and human amniotic epithelial cells determined by measurement of colonial diameters and growth curve as well as cell cycle analysis. Both immunofluorescence staining and immunoblotting showed that human ES cells cultured on hAMCs expressed stem cell markers such as Oct-3/4, Sox2, and NANOG. Verified by embryoid body formation in vitro and teratoma formation in vivo, we found out that after 20 passages of culture, human ES cells grown on hAMCs feeders could still retain the potency of differentiating into three germ layers. Taken together, our data suggested hAMCs may be safe feeder cells to sustain the propagation of human ES cells in undifferentiated state for future therapeutic use.

A Study of Economical Incentives for Voltage Profile Control Method in Future Distribution Network

NASA Astrophysics Data System (ADS)

Tsuji, Takao; Sato, Noriyuki; Hashiguchi, Takuhei; Goda, Tadahiro; Tange, Seiji; Nomura, Toshio

In a future distribution network, it is difficult to maintain system voltage because a large number of distributed generators are introduced to the system. The authors have proposed “voltage profile control method” using power factor control of distributed generators in the previous work. However, the economical disbenefit is caused by the active power decrease when the power factor is controlled in order to increase the reactive power. Therefore, proper incentives must be given to the customers that corporate to the voltage profile control method. Thus, in this paper, we develop a new rules which can decide the economical incentives to the customers. The method is tested in one feeder distribution network model and its effectiveness is shown.

Intelligent decision support algorithm for distribution system restoration.

PubMed

Singh, Reetu; Mehfuz, Shabana; Kumar, Parmod

2016-01-01

Distribution system is the means of revenue for electric utility. It needs to be restored at the earliest if any feeder or complete system is tripped out due to fault or any other cause. Further, uncertainty of the loads, result in variations in the distribution network's parameters. Thus, an intelligent algorithm incorporating hybrid fuzzy-grey relation, which can take into account the uncertainties and compare the sequences is discussed to analyse and restore the distribution system. The simulation studies are carried out to show the utility of the method by ranking the restoration plans for a typical distribution system. This algorithm also meets the smart grid requirements in terms of an automated restoration plan for the partial/full blackout of network.

Distributed optimization system and method

DOEpatents

Hurtado, John E.; Dohrmann, Clark R.; Robinett, III, Rush D.

2003-06-10

A search system and method for controlling multiple agents to optimize an objective using distributed sensing and cooperative control. The search agent can be one or more physical agents, such as a robot, and can be software agents for searching cyberspace. The objective can be: chemical sources, temperature sources, radiation sources, light sources, evaders, trespassers, explosive sources, time dependent sources, time independent sources, function surfaces, maximization points, minimization points, and optimal control of a system such as a communication system, an economy, a crane, and a multi-processor computer.

Distributed Optimization System

DOEpatents

Hurtado, John E.; Dohrmann, Clark R.; Robinett, III, Rush D.

2004-11-30

A search system and method for controlling multiple agents to optimize an objective using distributed sensing and cooperative control. The search agent can be one or more physical agents, such as a robot, and can be software agents for searching cyberspace. The objective can be: chemical sources, temperature sources, radiation sources, light sources, evaders, trespassers, explosive sources, time dependent sources, time independent sources, function surfaces, maximization points, minimization points, and optimal control of a system such as a communication system, an economy, a crane, and a multi-processor computer.

GridPV Toolbox

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broderick, Robert; Quiroz, Jimmy; Grijalva, Santiago

2014-07-15

Matlab Toolbox for simulating the impact of solar energy on the distribution grid. The majority of the functions are useful for interfacing OpenDSS and MATLAB, and they are of generic use for commanding OpenDSS from MATLAB and retrieving GridPV Toolbox information from simulations. A set of functions is also included for modeling PV plant output and setting up the PV plant in the OpenDSS simulation. The toolbox contains functions for modeling the OpenDSS distribution feeder on satellite images with GPS coordinates. Finally, example simulations functions are included to show potential uses of the toolbox functions.

Self-healing ring-based WDM-PON

NASA Astrophysics Data System (ADS)

Zhou, Yang; Gan, Chaoqin; Zhu, Long

2010-05-01

In this paper, a survivable ring-based wavelength-division-multiplexing (WDM)-passive optical network (PON) for fiber protection is proposed. Protections for feeder fiber and distributed fiber are independent in the scheme. Optical line terminal (OLT) and optical network units (ONUs) can automatically switch to protection link when fiber failure occurs. Protection distributed fiber is not required in the scheme. Cost-effective components are used in ONUs to minimize costs of network. A simulation study is performed to demonstrate the scheme. Its result shows good performance of upstream and downstream signals.

46 CFR 111.75-1 - Lighting feeders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Lighting Circuits and Protection § 111.75-1 Lighting feeders. (a) Passenger vessels. On a... lighting, feeders, and branch circuits are in subpart 112.43 of this chapter. [CGD 74-125A, 47 FR 15236...

A distributed component framework for science data product interoperability

NASA Technical Reports Server (NTRS)

Crichton, D.; Hughes, S.; Kelly, S.; Hardman, S.

2000-01-01

Correlation of science results from multi-disciplinary communities is a difficult task. Traditionally data from science missions is archived in proprietary data systems that are not interoperable. The Object Oriented Data Technology (OODT) task at the Jet Propulsion Laboratory is working on building a distributed product server as part of a distributed component framework to allow heterogeneous data systems to communicate and share scientific results.

46 CFR 112.43-15 - Emergency lighting feeders.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 4 2011-10-01 2011-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...

46 CFR 112.43-15 - Emergency lighting feeders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...

46 CFR 112.43-15 - Emergency lighting feeders.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 4 2014-10-01 2014-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...

46 CFR 112.43-15 - Emergency lighting feeders.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 4 2012-10-01 2012-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...

46 CFR 112.43-15 - Emergency lighting feeders.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 4 2013-10-01 2013-10-01 false Emergency lighting feeders. 112.43-15 Section 112.43-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Lighting Systems § 112.43-15 Emergency lighting feeders. For a vessel with...

77 FR 34876 - Airworthiness Directives; The Boeing Company

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-12

... (a flammable fluid leakage zone) or heat damage to the APU power feeder cable, insulation blankets... heat damage to the APU power feeder cable, insulation blankets, or pressure bulkhead. Relevant Service... feeder cable and heat damage of the insulation blanket adjacent to the clamp, a detailed inspection for...

Feederism in a woman.

PubMed

Terry, Lesley L; Vasey, Paul L

2011-06-01

Feederism is a fat fetish subculture in which individuals eroticize weight gain and feeding. Feeders are individuals who claim to become sexually aroused by feeding their partners and encouraging them to gain weight. Conversely, Feedees are individuals who claim to become sexually aroused by eating, being fed, and the idea or act of gaining weight. Very little is known about this population. This report describes a woman who self-identified as a Feedee. It is unclear, at present, whether female Feederism represents a unique paraphilia or a thematic variation of morphophilia or sexual masochism.

Changes in food intake and abnormal behavior using a puzzle feeder in newly acquired sub-adult rhesus monkeys (Macaca mulatta): a short term study.

PubMed

Lee, Jae-Il; Lee, Chi-Woo; Kwon, Hyouk-Sang; Kim, Young-Tae; Park, Chung-Gyu; Kim, Sang-Joon; Kang, Byeong-Cheol

2008-10-01

The majority of newly acquired nonhuman primates encounter serious problems adapting themselves to new environments or facilities. In particular, loss of appetite and abnormal behavior can occur in response to environmental stresses. These adaptation abnormalities can ultimately have an affect on the animal's growth and well-being. In this study, we evaluated the affects of a puzzle feeder on the food intake and abnormal behavior of newly acquired rhesus monkeys for a short period. The puzzle feeder was applied to 47- to 58-month-old animals that had never previously encountered one. We found that there was no difference in the change of food intake between the bucket condition and the puzzle feeder condition. In contrast, the time spent for consumption of food was three times longer in the puzzle feeder condition than in the bucket condition. Two monkeys initially exhibited stereotypic behavior. One showed a decreasing, and the other an increasing pattern of abnormal behavior after introduction of the puzzle feeder. In conclusion, this result suggests that over a short period, the puzzle feeder can only affect the time for food consumption since it failed to affect the food intake and did not consistently influence stereotypic behaviors in newly acquired rhesus monkeys.

Fabrication of corneal epithelial cell sheets maintaining colony-forming cells without feeder cells by oxygen-controlled method.

PubMed

Nakajima, Ryota; Takeda, Shizu

2014-01-01

The use of murine 3T3 feeder cells needs to be avoided when fabricating corneal epithelial cell sheets for use in treating ocular surface diseases. However, the expression level of the epithelial stem/progenitor cell marker, p63, is down-regulated in feeder-free culture systems. In this study, in order to fabricate corneal epithelial cell sheets that maintain colony-forming cells without using any feeder cells, we investigated the use of an oxygen-controlled method that was developed previously to fabricate cell sheets efficiently. Rabbit limbal epithelial cells were cultured under hypoxia (1-10% O2) and under normoxia during stratification after reaching confluence. Multilayered corneal epithelial cell sheets were fabricated using an oxygen-controlled method, and immunofluorescence analysis showed that cytokeratin 3 and p63 was expressed in appropriate localization in the cell sheets. The colony-forming efficiency of the cell sheets fabricated by the oxygen-controlled method without feeder cells was significantly higher than that of cell sheets fabricated under 20% O2 without feeder cells. These results indicate that the oxygen-controlled method has the potential to achieve a feeder-free culture system for fabricating corneal epithelial cell sheets for corneal regeneration. Copyright © 2013 Elsevier Ltd. All rights reserved.

Optimal coordinated voltage control in active distribution networks using backtracking search algorithm

PubMed Central

Tengku Hashim, Tengku Juhana; Mohamed, Azah

2017-01-01

The growing interest in distributed generation (DG) in recent years has led to a number of generators connected to a distribution system. The integration of DGs in a distribution system has resulted in a network known as active distribution network due to the existence of bidirectional power flow in the system. Voltage rise issue is one of the predominantly important technical issues to be addressed when DGs exist in an active distribution network. This paper presents the application of the backtracking search algorithm (BSA), which is relatively new optimisation technique to determine the optimal settings of coordinated voltage control in a distribution system. The coordinated voltage control considers power factor, on-load tap-changer and generation curtailment control to manage voltage rise issue. A multi-objective function is formulated to minimise total losses and voltage deviation in a distribution system. The proposed BSA is compared with that of particle swarm optimisation (PSO) so as to evaluate its effectiveness in determining the optimal settings of power factor, tap-changer and percentage active power generation to be curtailed. The load flow algorithm from MATPOWER is integrated in the MATLAB environment to solve the multi-objective optimisation problem. Both the BSA and PSO optimisation techniques have been tested on a radial 13-bus distribution system and the results show that the BSA performs better than PSO by providing better fitness value and convergence rate. PMID:28991919

Optimal coordinated voltage control in active distribution networks using backtracking search algorithm.

PubMed

Tengku Hashim, Tengku Juhana; Mohamed, Azah

2017-01-01

The growing interest in distributed generation (DG) in recent years has led to a number of generators connected to a distribution system. The integration of DGs in a distribution system has resulted in a network known as active distribution network due to the existence of bidirectional power flow in the system. Voltage rise issue is one of the predominantly important technical issues to be addressed when DGs exist in an active distribution network. This paper presents the application of the backtracking search algorithm (BSA), which is relatively new optimisation technique to determine the optimal settings of coordinated voltage control in a distribution system. The coordinated voltage control considers power factor, on-load tap-changer and generation curtailment control to manage voltage rise issue. A multi-objective function is formulated to minimise total losses and voltage deviation in a distribution system. The proposed BSA is compared with that of particle swarm optimisation (PSO) so as to evaluate its effectiveness in determining the optimal settings of power factor, tap-changer and percentage active power generation to be curtailed. The load flow algorithm from MATPOWER is integrated in the MATLAB environment to solve the multi-objective optimisation problem. Both the BSA and PSO optimisation techniques have been tested on a radial 13-bus distribution system and the results show that the BSA performs better than PSO by providing better fitness value and convergence rate.

2D and 3D X-ray phase retrieval of multi-material objects using a single defocus distance.

PubMed

Beltran, M A; Paganin, D M; Uesugi, K; Kitchen, M J

2010-03-29

A method of tomographic phase retrieval is developed for multi-material objects whose components each has a distinct complex refractive index. The phase-retrieval algorithm, based on the Transport-of-Intensity equation, utilizes propagation-based X-ray phase contrast images acquired at a single defocus distance for each tomographic projection. The method requires a priori knowledge of the complex refractive index for each material present in the sample, together with the total projected thickness of the object at each orientation. The requirement of only a single defocus distance per projection simplifies the experimental setup and imposes no additional dose compared to conventional tomography. The algorithm was implemented using phase contrast data acquired at the SPring-8 Synchrotron facility in Japan. The three-dimensional (3D) complex refractive index distribution of a multi-material test object was quantitatively reconstructed using a single X-ray phase-contrast image per projection. The technique is robust in the presence of noise, compared to conventional absorption based tomography.

Removing Barriers for Effective Deployment of Intermittent Renewable Generation

NASA Astrophysics Data System (ADS)

Arabali, Amirsaman

The stochastic nature of intermittent renewable resources is the main barrier to effective integration of renewable generation. This problem can be studied from feeder-scale and grid-scale perspectives. Two new stochastic methods are proposed to meet the feeder-scale controllable load with a hybrid renewable generation (including wind and PV) and energy storage system. For the first method, an optimization problem is developed whose objective function is the cost of the hybrid system including the cost of renewable generation and storage subject to constraints on energy storage and shifted load. A smart-grid strategy is developed to shift the load and match the renewable energy generation and controllable load. Minimizing the cost function guarantees minimum PV and wind generation installation, as well as storage capacity selection for supplying the controllable load. A confidence coefficient is allocated to each stochastic constraint which shows to what degree the constraint is satisfied. In the second method, a stochastic framework is developed for optimal sizing and reliability analysis of a hybrid power system including renewable resources (PV and wind) and energy storage system. The hybrid power system is optimally sized to satisfy the controllable load with a specified reliability level. A load-shifting strategy is added to provide more flexibility for the system and decrease the installation cost. Load shifting strategies and their potential impacts on the hybrid system reliability/cost analysis are evaluated trough different scenarios. Using a compromise-solution method, the best compromise between the reliability and cost will be realized for the hybrid system. For the second problem, a grid-scale stochastic framework is developed to examine the storage application and its optimal placement for the social cost and transmission congestion relief of wind integration. Storage systems are optimally placed and adequately sized to minimize the sum of operation and congestion costs over a scheduling period. A technical assessment framework is developed to enhance the efficiency of wind integration and evaluate the economics of storage technologies and conventional gas-fired alternatives. The proposed method is used to carry out a cost-benefit analysis for the IEEE 24-bus system and determine the most economical technology. In order to mitigate the financial and technical concerns of renewable energy integration into the power system, a stochastic framework is proposed for transmission grid reinforcement studies in a power system with wind generation. A multi-stage multi-objective transmission network expansion planning (TNEP) methodology is developed which considers the investment cost, absorption of private investment and reliability of the system as the objective functions. A Non-dominated Sorting Genetic Algorithm (NSGA II) optimization approach is used in combination with a probabilistic optimal power flow (POPF) to determine the Pareto optimal solutions considering the power system uncertainties. Using a compromise-solution method, the best final plan is then realized based on the decision maker preferences. The proposed methodology is applied to the IEEE 24-bus Reliability Tests System (RTS) to evaluate the feasibility and practicality of the developed planning strategy.

An optimal autonomous microgrid cluster based on distributed generation droop parameter optimization and renewable energy sources using an improved grey wolf optimizer

NASA Astrophysics Data System (ADS)

Moazami Goodarzi, Hamed; Kazemi, Mohammad Hosein

2018-05-01

Microgrid (MG) clustering is regarded as an important driver in improving the robustness of MGs. However, little research has been conducted on providing appropriate MG clustering. This article addresses this shortfall. It proposes a novel multi-objective optimization approach for finding optimal clustering of autonomous MGs by focusing on variables such as distributed generation (DG) droop parameters, the location and capacity of DG units, renewable energy sources, capacitors and powerline transmission. Power losses are minimized and voltage stability is improved while virtual cut-set lines with minimum power transmission for clustering MGs are obtained. A novel chaotic grey wolf optimizer (CGWO) algorithm is applied to solve the proposed multi-objective problem. The performance of the approach is evaluated by utilizing a 69-bus MG in several scenarios.

Multi-class geospatial object detection based on a position-sensitive balancing framework for high spatial resolution remote sensing imagery

NASA Astrophysics Data System (ADS)

Zhong, Yanfei; Han, Xiaobing; Zhang, Liangpei

2018-04-01

Multi-class geospatial object detection from high spatial resolution (HSR) remote sensing imagery is attracting increasing attention in a wide range of object-related civil and engineering applications. However, the distribution of objects in HSR remote sensing imagery is location-variable and complicated, and how to accurately detect the objects in HSR remote sensing imagery is a critical problem. Due to the powerful feature extraction and representation capability of deep learning, the deep learning based region proposal generation and object detection integrated framework has greatly promoted the performance of multi-class geospatial object detection for HSR remote sensing imagery. However, due to the translation caused by the convolution operation in the convolutional neural network (CNN), although the performance of the classification stage is seldom influenced, the localization accuracies of the predicted bounding boxes in the detection stage are easily influenced. The dilemma between translation-invariance in the classification stage and translation-variance in the object detection stage has not been addressed for HSR remote sensing imagery, and causes position accuracy problems for multi-class geospatial object detection with region proposal generation and object detection. In order to further improve the performance of the region proposal generation and object detection integrated framework for HSR remote sensing imagery object detection, a position-sensitive balancing (PSB) framework is proposed in this paper for multi-class geospatial object detection from HSR remote sensing imagery. The proposed PSB framework takes full advantage of the fully convolutional network (FCN), on the basis of a residual network, and adopts the PSB framework to solve the dilemma between translation-invariance in the classification stage and translation-variance in the object detection stage. In addition, a pre-training mechanism is utilized to accelerate the training procedure and increase the robustness of the proposed algorithm. The proposed algorithm is validated with a publicly available 10-class object detection dataset.

A Survivable Wavelength Division Multiplexing Passive Optical Network with Both Point-to-Point Service and Broadcast Service Delivery

NASA Astrophysics Data System (ADS)

Ma, Xuejiao; Gan, Chaoqin; Deng, Shiqi; Huang, Yan

2011-11-01

A survivable wavelength division multiplexing passive optical network enabling both point-to-point service and broadcast service is presented and demonstrated. This architecture provides an automatic traffic recovery against feeder and distribution fiber link failure, respectively. In addition, it also simplifies the protection design for multiple services transmission in wavelength division multiplexing passive optical networks.

The AMSC mobile satellite system

NASA Technical Reports Server (NTRS)

Agnew, Carson E.; Bhagat, Jai; Hopper, Edwin A.; Kiesling, John D.; Exner, Michael L.; Melillo, Lawrence; Noreen, Gary K.; Parrott, Billy J.

1988-01-01

The American Mobile Satellite Consortium (AMSC) Mobile Satellite Service (MSS) system is described. AMSC will use three multi-beam satellites to provide L-band MSS coverage to the United States, Canada and Mexico. The AMSC MSS system will have several noteworthy features, including a priority assignment processor that will ensure preemptive access to emergency services, a flexible SCPC channel scheme that will support a wide diversity of services, enlarged system capacity through frequency and orbit reuse, and high effective satellite transmitted power. Each AMSC satellite will make use of 14 MHz (bi-directional) of L-band spectrum. The Ku-band will be used for feeder links.

Effect of a feeder layer composed of mouse embryonic and human foreskin fibroblasts on the proliferation of human embryonic stem cells.

PubMed

Yang, Hua; Qiu, Ying; Zeng, Xianghui; Ding, Yan; Zeng, Jianye; Lu, Kehuan; Li, Dongsheng

2016-06-01

The aim of the present study was to investigate the effects of feeder layers composed of various ratios of mouse embryonic fibroblasts (MEFs) and human foreskin fibroblasts (hFFs) on the growth of human embryonic stem cells (hESCs). In addition, the secretion levels of basic fibroblast growth factor (bFGF) by the feeder layers was detected. MEFs and hFFs were treated with mitomycin C and seeded onto gelatin-coated plates at a density of 1×10 8 cells/l. The hFFs and MEFs were combined and plated at the following ratios: 0:1, 1:2, 1:1, 2:1 and 1:0. The secretion of bFGF by the various hFF/MEF ratio feeder layers was detected using an enzyme-linked immunosorbent assay. Subsequently, hESCs were cultured on top of the various feeder layers. The differences in the cellular morphology of the hESCs were observed using microscopy, and the expression levels alkaline phosphatase (AKP) and octamer-binding transcription factor 4 (OCT-4) were detected using immunohistochemical analysis as indicators of differentiation status. The results showed that the hFFs secreted substantial quantities of bFGF, while no bFGF was secreted by the MEFs. The clones of hESC growing on the feeder layer containing MEF or hFF alone were flat. By contrast, hESC clones grown on a mixed feeder layer containing hFFs + MEFs at a ratio of 1:1 exhibited an accumulated growth with a clear edge, as compared with the other ratios. In addition, hESCs growing on the feeder layer were positive for the expression of AKP and OCT-4. In summary, feeder layer hFFs secreted bFGF, while MEFs did not, indicating that bFGF is not the only factor that supports the growth and differentiation of hESCs. The optimal growth of hESCs was achieved using a mixed feeder layer composed of hFFs + MEFs at a ratio of 1:1.

Prevalence and risk factors of Toxoplasma gondii in fattening pigs farm from Yucatan, Mexico.

PubMed

Ortega-Pacheco, A; Acosta Viana, K Y; Guzmán-Marín, E; Segura-Correa, J C; Alvarez-Fleites, M; Jiménez-Coello, M

2013-01-01

The objective of this study was to estimate the prevalence and identify risk factors associated with the presence of Toxoplasma gondii in pig-fattening farms from Yucatan, Mexico. A cross-sectional study was conducted with a two-stage sampling. There were 429 pigs sampled from 39 farms randomly selected. Blood samples were collected to obtain DNA and serum. The presence of IgM and IgG antibodies was determined by indirect ELISA. Prevalence was estimated by diagnostic test. Potential risk factors to be included in a marginal logistic regression were tested by chi-square or Fisher. The prevalence of IgM and IgG was 92.5% (397/429) (CI 89.9-95.1%) and 95.8% (411/429) (CI 93.7-97.8%), respectively. Regarding PCR, a prevalence of 50.8% (218/429) (CI 45.9-55.6%) was found. The logistic regression showed an association with herd size and type of feeder (P < 0.05). The risk of a case in farms with ≤400 pigs was 27.9 times higher than in farms with >400 pigs. The manual feeder was a significant protective factor associated with the seropositive against T. gondii. Results indicate a high circulation of T. gondii in pig-fattening farms from Yucatan, finding an increased risk of infection for those farms with less than 400 animals and automatic feeders.

Climate as a driver of continent-wide irruptions in boreal seed-eating birds (Invited)

NASA Astrophysics Data System (ADS)

Strong, C.; Zuckerberg, B.; Betancourt, J. L.

2013-12-01

Boreal seed-eating birds regularly breed and overwinter throughout Canada and Alaska, but every few years these species demonstrate impressive irruptive migrations out of the boreal forest and into more southerly regions. It is thought that irruptive migrations are inversely dependent on a circumboreally synchronized pattern of seed crop fluctuations in boreal trees; seed-eating boreal birds stay in the north when food is plentiful, but sojourn south when food is scarce. Because both seed production and bird irruptions are characterized by periodicity ranging from biennial to decadal cycles, there is a strong possibility that these ecological phenomena are driven by climate variability. Using over twenty years of data from Project FeederWatch (a national citizen science project), we found that 'super irruptions' are correlated with continent-wide irruptive events in pine siskin population, and that these irruptions are associated with multi-decadal climate variability of Pacific origin. We also investigate how climate variability may influence the distribution of boreal bird species across different regions of North America during winter, and evaluate results in the context of limited banding data to assess possible geographic pathways of irruptions.

The innate responses of bumble bees to flower patterns: separating the nectar guide from the nectary changes bee movements and search time

NASA Astrophysics Data System (ADS)

Goodale, Eben; Kim, Edward; Nabors, Annika; Henrichon, Sara; Nieh, James C.

2014-06-01

Nectar guides can enhance pollinator efficiency and plant fitness by allowing pollinators to more rapidly find and remember the location of floral nectar. We tested if a radiating nectar guide around a nectary would enhance the ability of naïve bumble bee foragers to find nectar. Most experiments that test nectar guide efficacy, specifically radiating linear guides, have used guides positioned around the center of a radially symmetric flower, where nectaries are often found. However, the flower center may be intrinsically attractive. We therefore used an off-center guide and nectary and compared "conjunct" feeders with a nectar guide surrounding the nectary to "disjunct" feeders with a nectar guide separated from the nectary. We focused on the innate response of novice bee foragers that had never previously visited such feeders. We hypothesized that a disjunct nectar guide would conflict with the visual information provided by the nectary and negatively affect foraging. Approximately, equal numbers of bumble bees ( Bombus impatiens) found nectar on both feeder types. On disjunct feeders, however, unsuccessful foragers spent significantly more time (on average 1.6-fold longer) searching for nectar than any other forager group. Successful foragers on disjunct feeders approached these feeders from random directions unlike successful foragers on conjunct feeders, which preferentially approached the combined nectary and nectar guide. Thus, the nectary and a surrounding nectar guide can be considered a combination of two signals that attract naïve foragers even when not in the floral center.

The innate responses of bumble bees to flower patterns: separating the nectar guide from the nectary changes bee movements and search time.

PubMed

Goodale, Eben; Kim, Edward; Nabors, Annika; Henrichon, Sara; Nieh, James C

2014-06-01

Nectar guides can enhance pollinator efficiency and plant fitness by allowing pollinators to more rapidly find and remember the location of floral nectar. We tested if a radiating nectar guide around a nectary would enhance the ability of naïve bumble bee foragers to find nectar. Most experiments that test nectar guide efficacy, specifically radiating linear guides, have used guides positioned around the center of a radially symmetric flower, where nectaries are often found. However, the flower center may be intrinsically attractive. We therefore used an off-center guide and nectary and compared "conjunct" feeders with a nectar guide surrounding the nectary to "disjunct" feeders with a nectar guide separated from the nectary. We focused on the innate response of novice bee foragers that had never previously visited such feeders. We hypothesized that a disjunct nectar guide would conflict with the visual information provided by the nectary and negatively affect foraging. Approximately, equal numbers of bumble bees (Bombus impatiens) found nectar on both feeder types. On disjunct feeders, however, unsuccessful foragers spent significantly more time (on average 1.6-fold longer) searching for nectar than any other forager group. Successful foragers on disjunct feeders approached these feeders from random directions unlike successful foragers on conjunct feeders, which preferentially approached the combined nectary and nectar guide. Thus, the nectary and a surrounding nectar guide can be considered a combination of two signals that attract naïve foragers even when not in the floral center.

Resilience-based optimal design of water distribution network

NASA Astrophysics Data System (ADS)

Suribabu, C. R.

2017-11-01

Optimal design of water distribution network is generally aimed to minimize the capital cost of the investments on tanks, pipes, pumps, and other appurtenances. Minimizing the cost of pipes is usually considered as a prime objective as its proportion in capital cost of the water distribution system project is very high. However, minimizing the capital cost of the pipeline alone may result in economical network configuration, but it may not be a promising solution in terms of resilience point of view. Resilience of the water distribution network has been considered as one of the popular surrogate measures to address ability of network to withstand failure scenarios. To improve the resiliency of the network, the pipe network optimization can be performed with two objectives, namely minimizing the capital cost as first objective and maximizing resilience measure of the configuration as secondary objective. In the present work, these two objectives are combined as single objective and optimization problem is solved by differential evolution technique. The paper illustrates the procedure for normalizing the objective functions having distinct metrics. Two of the existing resilience indices and power efficiency are considered for optimal design of water distribution network. The proposed normalized objective function is found to be efficient under weighted method of handling multi-objective water distribution design problem. The numerical results of the design indicate the importance of sizing pipe telescopically along shortest path of flow to have enhanced resiliency indices.

26 CFR 1.502-1 - Feeder organizations.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 26 Internal Revenue 7 2010-04-01 2010-04-01 true Feeder organizations. 1.502-1 Section 1.502-1...) INCOME TAXES (CONTINUED) Exempt Organizations § 1.502-1 Feeder organizations. (a) In the case of an organization operated for the primary purpose of carrying on a trade or business for profit, exemption is not...

75 FR 8395 - Bunker Hill Groundwater Basin, Riverside-Corona Feeder Project, San Bernardino and Riverside...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-24

... DEPARTMENT OF THE INTERIOR Bureau of Reclamation Bunker Hill Groundwater Basin, Riverside-Corona...) will prepare a joint EIS/EIR for the proposed Riverside-Corona Feeder Project. The public and agencies... participate in the planning, design, and construction of the Riverside-Corona Feeder Project including: (i) 20...

7 CFR 1230.71 - Assessments.

Code of Federal Regulations, 2011 CFR

2011-01-01

... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...

7 CFR 1230.71 - Assessments.

Code of Federal Regulations, 2010 CFR

2010-01-01

... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...

7 CFR 1230.71 - Assessments.

Code of Federal Regulations, 2012 CFR

2012-01-01

... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...

7 CFR 1230.71 - Assessments.

Code of Federal Regulations, 2014 CFR

2014-01-01

... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...

7 CFR 1230.71 - Assessments.

Code of Federal Regulations, 2013 CFR

2013-01-01

... feeder pig that is sold shall pay an assessment on that animal, unless such producer demonstrates to the Board by appropriate documentation that an assessment was previously paid on that animal as a feeder pig... purchaser of a porcine animal raised by a producer as a feeder pig or market hog shall collect an assessment...

A Multistate Investigation of Antibiotic-Resistant Salmonella enterica Serotype I 4,[5],12:i:- Infections as Part of an International Outbreak Associated with Frozen Feeder Rodents

PubMed Central

Cartwright, E. J.; Nguyen, T.; Melluso, C.; Ayers, T.; Lane, C.; Hodges, A.; Li, X.; Quammen, J.; Yendell, S. J.; Adams, J.; Mitchell, J.; Rickert, R.; Klos, R.; Williams, I. T.; Behravesh, C. Barton; Wright, J.

2015-01-01

While most human Salmonella infections result from exposure to contaminated foods, an estimated 11% of all Salmonella infections are attributed to animal exposures, including both direct animal handling and indirect exposures such as cleaning cages and handling contaminated pet food. This report describes the epidemiologic, environmental and laboratory investigations conducted in the United States as part of the response to an international outbreak of tetracycline-resistant Salmonella enterica serotype I 4,[5],12:i:- infections with over 500 illnesses occurring from 2008 to 2010. This investigation found that illness due to the outbreak strain was significantly associated with exposure to pet reptiles and frozen feeder rodents used as food for pet reptiles. Salmonella isolates indistinguishable from the outbreak strain were isolated from a frozen feeder mice-fed reptile owned by a case patient, as well as from frozen feeder mice and environmental samples collected from a rodent producing facility (Company A). An international voluntary recall of all Company A produced frozen feeder animals sold between May 2009 and July 2010 occurred. Only 13% of cases in our investigation were aware of the association between Salmonella infection and mice or rats. Consumers, the pet industry, healthcare providers and veterinarians need to be aware of the potential health risk posed by feeder rodents, whether live or frozen. Frozen feeder rodent producers, suppliers and distributors should follow the animal food labelling requirements as described in 21 CFR §501.5, and all packages of frozen feeder rodents should include safe handling instructions. Persons should wash their hands thoroughly with soap and water after handling live or frozen feeder rodents, as well as reptiles or anything in the area where the animals live. Continued opportunities exist for public health officials, the pet industry, veterinarians and consumers to work together to prevent salmonellosis associated with pet food, pets and other animals. PMID:25996458

A Multistate Investigation of Antibiotic-Resistant Salmonella enterica Serotype I 4,[5],12:i:- Infections as Part of an International Outbreak Associated with Frozen Feeder Rodents.

PubMed

Cartwright, E J; Nguyen, T; Melluso, C; Ayers, T; Lane, C; Hodges, A; Li, X; Quammen, J; Yendell, S J; Adams, J; Mitchell, J; Rickert, R; Klos, R; Williams, I T; Barton Behravesh, C; Wright, J

2016-02-01

While most human Salmonella infections result from exposure to contaminated foods, an estimated 11% of all Salmonella infections are attributed to animal exposures, including both direct animal handling and indirect exposures such as cleaning cages and handling contaminated pet food. This report describes the epidemiologic, environmental and laboratory investigations conducted in the United States as part of the response to an international outbreak of tetracycline-resistant Salmonella enterica serotype I 4,[5],12:i:- infections with over 500 illnesses occurring from 2008 to 2010. This investigation found that illness due to the outbreak strain was significantly associated with exposure to pet reptiles and frozen feeder rodents used as food for pet reptiles. Salmonella isolates indistinguishable from the outbreak strain were isolated from a frozen feeder mice-fed reptile owned by a case patient, as well as from frozen feeder mice and environmental samples collected from a rodent producing facility (Company A). An international voluntary recall of all Company A produced frozen feeder animals sold between May 2009 and July 2010 occurred. Only 13% of cases in our investigation were aware of the association between Salmonella infection and mice or rats. Consumers, the pet industry, healthcare providers and veterinarians need to be aware of the potential health risk posed by feeder rodents, whether live or frozen. Frozen feeder rodent producers, suppliers and distributors should follow the animal food labelling requirements as described in 21 CFR §501.5, and all packages of frozen feeder rodents should include safe handling instructions. Persons should wash their hands thoroughly with soap and water after handling live or frozen feeder rodents, as well as reptiles or anything in the area where the animals live. Continued opportunities exist for public health officials, the pet industry, veterinarians and consumers to work together to prevent salmonellosis associated with pet food, pets and other animals. © 2015 Blackwell Verlag GmbH.

A master-slave parallel hybrid multi-objective evolutionary algorithm for groundwater remediation design under general hydrogeological conditions

NASA Astrophysics Data System (ADS)

Wu, J.; Yang, Y.; Luo, Q.; Wu, J.

2012-12-01

This study presents a new hybrid multi-objective evolutionary algorithm, the niched Pareto tabu search combined with a genetic algorithm (NPTSGA), whereby the global search ability of niched Pareto tabu search (NPTS) is improved by the diversification of candidate solutions arose from the evolving nondominated sorting genetic algorithm II (NSGA-II) population. Also, the NPTSGA coupled with the commonly used groundwater flow and transport codes, MODFLOW and MT3DMS, is developed for multi-objective optimal design of groundwater remediation systems. The proposed methodology is then applied to a large-scale field groundwater remediation system for cleanup of large trichloroethylene (TCE) plume at the Massachusetts Military Reservation (MMR) in Cape Cod, Massachusetts. Furthermore, a master-slave (MS) parallelization scheme based on the Message Passing Interface (MPI) is incorporated into the NPTSGA to implement objective function evaluations in distributed processor environment, which can greatly improve the efficiency of the NPTSGA in finding Pareto-optimal solutions to the real-world application. This study shows that the MS parallel NPTSGA in comparison with the original NPTS and NSGA-II can balance the tradeoff between diversity and optimality of solutions during the search process and is an efficient and effective tool for optimizing the multi-objective design of groundwater remediation systems under complicated hydrogeologic conditions.

A multi-objective framework to predict flows of ungauged rivers within regions of sparse hydrometeorologic observation

NASA Astrophysics Data System (ADS)

Alipour, M.; Kibler, K. M.

2017-12-01

Despite advances in flow prediction, managers of ungauged rivers located within broad regions of sparse hydrometeorologic observation still lack prescriptive methods robust to the data challenges of such regions. We propose a multi-objective streamflow prediction framework for regions of minimum observation to select models that balance runoff efficiency with choice of accurate parameter values. We supplement sparse observed data with uncertain or low-resolution information incorporated as `soft' a priori parameter estimates. The performance of the proposed framework is tested against traditional single-objective and constrained single-objective calibrations in two catchments in a remote area of southwestern China. We find that the multi-objective approach performs well with respect to runoff efficiency in both catchments (NSE = 0.74 and 0.72), within the range of efficiencies returned by other models (NSE = 0.67 - 0.78). However, soil moisture capacity estimated by the multi-objective model resonates with a priori estimates (parameter residuals of 61 cm versus 289 and 518 cm for maximum soil moisture capacity in one catchment, and 20 cm versus 246 and 475 cm in the other; parameter residuals of 0.48 versus 0.65 and 0.7 for soil moisture distribution shape factor in one catchment, and 0.91 versus 0.79 and 1.24 in the other). Thus, optimization to a multi-criteria objective function led to very different representations of soil moisture capacity as compared to models selected by single-objective calibration, without compromising runoff efficiency. These different soil moisture representations may translate into considerably different hydrological behaviors. The proposed approach thus offers a preliminary step towards greater process understanding in regions of severe data limitations. For instance, the multi-objective framework may be an adept tool to discern between models of similar efficiency to select models that provide the "right answers for the right reasons". Managers may feel more confident to utilize such models to predict flows in fully ungauged areas.

Interconnection, Integration, and Interactive Impact Analysis of Microgrids and Distribution Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kang, Ning; Wang, Jianhui; Singh, Ravindra

2017-01-01

Distribution management systems (DMSs) are increasingly used by distribution system operators (DSOs) to manage the distribution grid and to monitor the status of both power imported from the transmission grid and power generated locally by a distributed energy resource (DER), to ensure that power flows and voltages along the feeders are maintained within designed limits and that appropriate measures are taken to guarantee service continuity and energy security. When microgrids are deployed and interconnected to the distribution grids, they will have an impact on the operation of the distribution grid. The challenge is to design this interconnection in such amore » way that it enhances the reliability and security of the distribution grid and the loads embedded in the microgrid, while providing economic benefits to all stakeholders, including the microgrid owner and operator and the distribution system operator.« less

A Pareto-based Ensemble with Feature and Instance Selection for Learning from Multi-Class Imbalanced Datasets.

PubMed

Fernández, Alberto; Carmona, Cristobal José; José Del Jesus, María; Herrera, Francisco

2017-09-01

Imbalanced classification is related to those problems that have an uneven distribution among classes. In addition to the former, when instances are located into the overlapped areas, the correct modeling of the problem becomes harder. Current solutions for both issues are often focused on the binary case study, as multi-class datasets require an additional effort to be addressed. In this research, we overcome these problems by carrying out a combination between feature and instance selections. Feature selection will allow simplifying the overlapping areas easing the generation of rules to distinguish among the classes. Selection of instances from all classes will address the imbalance itself by finding the most appropriate class distribution for the learning task, as well as possibly removing noise and difficult borderline examples. For the sake of obtaining an optimal joint set of features and instances, we embedded the searching for both parameters in a Multi-Objective Evolutionary Algorithm, using the C4.5 decision tree as baseline classifier in this wrapper approach. The multi-objective scheme allows taking a double advantage: the search space becomes broader, and we may provide a set of different solutions in order to build an ensemble of classifiers. This proposal has been contrasted versus several state-of-the-art solutions on imbalanced classification showing excellent results in both binary and multi-class problems.

Optimizing Constrained Single Period Problem under Random Fuzzy Demand

NASA Astrophysics Data System (ADS)

Taleizadeh, Ata Allah; Shavandi, Hassan; Riazi, Afshin

2008-09-01

In this paper, we consider the multi-product multi-constraint newsboy problem with random fuzzy demands and total discount. The demand of the products is often stochastic in the real word but the estimation of the parameters of distribution function may be done by fuzzy manner. So an appropriate option to modeling the demand of products is using the random fuzzy variable. The objective function of proposed model is to maximize the expected profit of newsboy. We consider the constraints such as warehouse space and restriction on quantity order for products, and restriction on budget. We also consider the batch size for products order. Finally we introduce a random fuzzy multi-product multi-constraint newsboy problem (RFM-PM-CNP) and it is changed to a multi-objective mixed integer nonlinear programming model. Furthermore, a hybrid intelligent algorithm based on genetic algorithm, Pareto and TOPSIS is presented for the developed model. Finally an illustrative example is presented to show the performance of the developed model and algorithm.

MultiMiTar: a novel multi objective optimization based miRNA-target prediction method.

PubMed

Mitra, Ramkrishna; Bandyopadhyay, Sanghamitra

2011-01-01

Machine learning based miRNA-target prediction algorithms often fail to obtain a balanced prediction accuracy in terms of both sensitivity and specificity due to lack of the gold standard of negative examples, miRNA-targeting site context specific relevant features and efficient feature selection process. Moreover, all the sequence, structure and machine learning based algorithms are unable to distribute the true positive predictions preferentially at the top of the ranked list; hence the algorithms become unreliable to the biologists. In addition, these algorithms fail to obtain considerable combination of precision and recall for the target transcripts that are translationally repressed at protein level. In the proposed article, we introduce an efficient miRNA-target prediction system MultiMiTar, a Support Vector Machine (SVM) based classifier integrated with a multiobjective metaheuristic based feature selection technique. The robust performance of the proposed method is mainly the result of using high quality negative examples and selection of biologically relevant miRNA-targeting site context specific features. The features are selected by using a novel feature selection technique AMOSA-SVM, that integrates the multi objective optimization technique Archived Multi-Objective Simulated Annealing (AMOSA) and SVM. MultiMiTar is found to achieve much higher Matthew's correlation coefficient (MCC) of 0.583 and average class-wise accuracy (ACA) of 0.8 compared to the others target prediction methods for a completely independent test data set. The obtained MCC and ACA values of these algorithms range from -0.269 to 0.155 and 0.321 to 0.582, respectively. Moreover, it shows a more balanced result in terms of precision and sensitivity (recall) for the translationally repressed data set as compared to all the other existing methods. An important aspect is that the true positive predictions are distributed preferentially at the top of the ranked list that makes MultiMiTar reliable for the biologists. MultiMiTar is now available as an online tool at www.isical.ac.in/~bioinfo_miu/multimitar.htm. MultiMiTar software can be downloaded from www.isical.ac.in/~bioinfo_miu/multimitar-download.htm.

Development of dry coal feeders

NASA Technical Reports Server (NTRS)

Bonin, J. H.; Cantey, D. E.; Daniel, A. D., Jr.; Meyer, J. W.

1977-01-01

Design and fabrication of equipment of feed coal into pressurized environments were investigated. Concepts were selected based on feeder system performance and economic projections. These systems include: two approaches using rotating components, a gas or steam driven ejector, and a modified standpipe feeder concept. Results of development testing of critical components, design procedures, and performance prediction techniques are reviewed.

Ornithologists by Design: Kindergarteners Design, Construct, and Evaluate Bird Feeders

ERIC Educational Resources Information Center

Shorter, Angela; Segers, Marcia

2016-01-01

How can an engineer design a bird feeder that attracts many birds? This question resulted from kindergarten students' observations of the bird feeders in their school's bird sanctuary. The challenging question is the heart of project-based learning (PBL), a teaching strategy in which students tackle real-world problems and design projects to solve…

19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

19. DETAIL OF STAMP BATTERY AUTOMATIC FEEDER, LOOKING EAST. THIS IS THE MIDDLE OF THREE FEEDERS, ONE FOR EACH STAMP BATTERY. THE CHUTE (UPPER RIGHT) INTRODUCED THE CRUSHED ORE FROM THE ORE BIN. FLOW WAS CONTROLLED BY A SLIDING DOOR ON THE UPPER LEVEL. - Skidoo Mine, Park Route 38 (Skidoo Road), Death Valley Junction, Inyo County, CA

Conversion and Validation of Distribution System Model from a QSTS-Based Tool to a Real-Time Dynamic Phasor Simulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chamana, Manohar; Prabakar, Kumaraguru; Palmintier, Bryan

A software process is developed to convert distribution network models from a quasi-static time-series tool (OpenDSS) to a real-time dynamic phasor simulator (ePHASORSIM). The description of this process in this paper would be helpful for researchers who intend to perform similar conversions. The converter could be utilized directly by users of real-time simulators who intend to perform software-in-the-loop or hardware-in-the-loop tests on large distribution test feeders for a range of use cases, including testing functions of advanced distribution management systems against a simulated distribution system. In the future, the developers intend to release the conversion tool as open source tomore » enable use by others.« less

Conversion and Validation of Distribution System Model from a QSTS-Based Tool to a Real-Time Dynamic Phasor Simulator: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chamana, Manohar; Prabakar, Kumaraguru; Palmintier, Bryan

A software process is developed to convert distribution network models from a quasi-static time-series tool (OpenDSS) to a real-time dynamic phasor simulator (ePHASORSIM). The description of this process in this paper would be helpful for researchers who intend to perform similar conversions. The converter could be utilized directly by users of real-time simulators who intend to perform software-in-the-loop or hardware-in-the-loop tests on large distribution test feeders for a range of use cases, including testing functions of advanced distribution management systems against a simulated distribution system. In the future, the developers intend to release the conversion tool as open source tomore » enable use by others.« less

Impact of feeder space on laying hen feeding behavior and production performance in enriched colony housing.

PubMed

Oliveira, J L; Xin, H; Wu, H

2018-05-30

Current feeder space recommendations in laying hen welfare guidelines are inconsistent among and within countries. One determining criterion forming the recommendations (e.g. 12.0 cm/hen for the EU guideline) is that all birds can feed simultaneously. However, if there are other resources in the environment, as in enriched colony housing (ECH), it is unknown whether group-housed hens will choose to feed simultaneously. This study assesses the impact of feeder space on feeding behavior of 60 laying hens (W-36) in ECH using a ultra-high frequency radio-frequency identification-based tracking system. The feeder spaces investigated were 12.0, 9.5, 8.5 and 6.5 cm/hen, achieved by blocking portions of the overall feeder access to keep hens at the same stocking density. Each feeder space treatment, randomly assigned over the course of the experiment, lasted for 7 consecutive days. Feeding behaviors were characterized as daily time spent at the feeder (TS, min/hen-day), daily frequency of visits to the feeder (FV, #/hen-day), and maximum or average percentage of hens feeding simultaneously (MPB, APB, %). Group-average daily feed intake (FI, g/hen-day), water use (WU, g/hen-day), and hen-day egg production (HDEP, %) were also measured. The results revealed that at 12.0 cm/hen, where unoccupied feeder space was present, a maximum of 59.0±1.4% (average of 31.7±0.3%) hens fed simultaneously. No significant differences were detected among 12.0, 9.5 and 8.5 cm/hen in TS (293±10, 286±10 and 281±10 min/hen-day) and MPB (59.0±1.4, 57.3±1.4 and 53.3±1.4%) (P>0.05). The outcome of no significant differences also held true between 12.0 and 9.5 cm/hen in APB (31.7±0.3 v. 30.8±0.3%) and between 9.5 and 8.5 cm/hen in all response variables measured (P>0.05). However, there were significant differences in APB between 6.5 cm/hen and all other treatments; in TS and FV between 6.5 and 9.5 cm/hen; and in MPB between 6.5 and 12 cm/hen (P0.05). The results revealed that synchronous feeding of hens in the ECH did not increase with increasing feeder space. However, it is worth noting that lower feeder space may lead to aggression or frustration which was not quantified in the current study.

A Three-Phase Microgrid Restoration Model Considering Unbalanced Operation of Distributed Generation

DOE PAGES

Wang, Zeyu; Wang, Jianhui; Chen, Chen

2016-12-07

Recent severe outages highlight the urgency of improving grid resiliency in the U.S. Microgrid formation schemes are proposed to restore critical loads after outages occur. Most distribution networks have unbalanced configurations that are not represented in sufficient detail by single-phase models. This study provides a microgrid formation plan that adopts a three-phase network model to represent unbalanced distribution networks. The problem formulation has a quadratic objective function with mixed-integer linear constraints. The three-phase network model enables us to examine the three-phase power outputs of distributed generators (DGs), preventing unbalanced operation that might trip DGs. Because the DG unbalanced operation constraintmore » is non-convex, an iterative process is presented that checks whether the unbalanced operation limits for DGs are satisfied after each iteration of optimization. We also develop a relatively conservative linear approximation on the unbalanced operation constraint to handle larger networks. Compared with the iterative solution process, the conservative linear approximation is able to accelerate the solution process at the cost of sacrificing optimality to a limited extent. Simulation in the IEEE 34 node and IEEE 123 test feeders indicate that the proposed method yields more practical microgrid formations results. In addition, this paper explores the coordinated operation of DGs and energy storage (ES) installations. The unbalanced three-phase outputs of ESs combined with the relatively balanced outputs of DGs could supply unbalanced loads. In conclusion, the case study also validates the DG-ES coordination.« less

A Three-Phase Microgrid Restoration Model Considering Unbalanced Operation of Distributed Generation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zeyu; Wang, Jianhui; Chen, Chen

Recent severe outages highlight the urgency of improving grid resiliency in the U.S. Microgrid formation schemes are proposed to restore critical loads after outages occur. Most distribution networks have unbalanced configurations that are not represented in sufficient detail by single-phase models. This study provides a microgrid formation plan that adopts a three-phase network model to represent unbalanced distribution networks. The problem formulation has a quadratic objective function with mixed-integer linear constraints. The three-phase network model enables us to examine the three-phase power outputs of distributed generators (DGs), preventing unbalanced operation that might trip DGs. Because the DG unbalanced operation constraintmore » is non-convex, an iterative process is presented that checks whether the unbalanced operation limits for DGs are satisfied after each iteration of optimization. We also develop a relatively conservative linear approximation on the unbalanced operation constraint to handle larger networks. Compared with the iterative solution process, the conservative linear approximation is able to accelerate the solution process at the cost of sacrificing optimality to a limited extent. Simulation in the IEEE 34 node and IEEE 123 test feeders indicate that the proposed method yields more practical microgrid formations results. In addition, this paper explores the coordinated operation of DGs and energy storage (ES) installations. The unbalanced three-phase outputs of ESs combined with the relatively balanced outputs of DGs could supply unbalanced loads. In conclusion, the case study also validates the DG-ES coordination.« less

Accuracy of software-assisted detection of tumour feeders in transcatheter hepatic chemoembolization using three target definition protocols.

PubMed

Iwazawa, J; Ohue, S; Hashimoto, N; Mitani, T

2014-02-01

To compare the accuracy of computer software analysis using three different target-definition protocols to detect tumour feeder vessels for transarterial chemoembolization of hepatocellular carcinoma. C-arm computed tomography (CT) data were analysed for 81 tumours from 57 patients who had undergone chemoembolization using software-assisted detection of tumour feeders. Small, medium, and large-sized targets were manually defined for each tumour. The tumour feeder was verified when the target tumour was enhanced on selective C-arm CT of the investigated vessel during chemoembolization. The sensitivity, specificity, and accuracy of the three protocols were evaluated and compared. One hundred and eight feeder vessels supplying 81 lesions were detected. The sensitivity of the small, medium, and large target protocols was 79.8%, 91.7%, and 96.3%, respectively; specificity was 95%, 88%, and 50%, respectively; and accuracy was 87.5%, 89.9%, and 74%, respectively. The sensitivity was significantly higher for the medium (p = 0.003) and large (p < 0.001) target protocols than for the small target protocol. The specificity and accuracy were higher for the small (p < 0.001 and p < 0.001, respectively) and medium (p < 0.001 and p < 0.001, respectively) target protocols than for the large target protocol. The overall accuracy of software-assisted automated feeder analysis in transarterial chemoembolization for hepatocellular carcinoma is affected by the target definition size. A large target definition increases sensitivity and decreases specificity in detecting tumour feeders. A target size equivalent to the tumour size most accurately predicts tumour feeders. Copyright © 2013 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Foraging scent marks of bumblebees: footprint cues rather than pheromone signals

NASA Astrophysics Data System (ADS)

Wilms, Jessica; Eltz, Thomas

2008-02-01

In their natural habitat foraging bumblebees refuse to land on and probe flowers that have been recently visited (and depleted) by themselves, conspecifics or other bees, which increases their overall rate of nectar intake. This avoidance is often based on recognition of scent marks deposited by previous visitors. While the term ‘scent mark’ implies active labelling, it is an open question whether the repellent chemicals are pheromones actively and specifically released during flower visits, or mere footprints deposited unspecifically wherever bees walk. To distinguish between the two possibilities, we presented worker bumblebees ( Bombus terrestris) with three types of feeders in a laboratory experiment: unvisited control feeders, passive feeders with a corolla that the bee had walked over on its way from the nest (with unspecific footprints), and active feeders, which the bee had just visited and depleted, but which were immediately refilled with sugar water (potentially with specific scent marks). Bumblebees rejected both active and passive feeders more frequently than unvisited controls. The rate of rejection of passive feeders was only slightly lower than that of active feeders, and this difference vanished completely when passive corollas were walked over repeatedly on the way from the nest. Thus, mere footprints were sufficient to emulate the repellent effect of an actual feeder visit. In confirmation, glass slides on which bumblebees had walked on near the nest entrance accumulated hydrocarbons (alkanes and alkenes, C23 to C31), which had previously been shown to elicit repellency in flower choice experiments. We conclude that repellent scent marks are mere footprints, which foraging bees avoid when they encounter them in a foraging context.

Expression and secretory profile of buffalo fetal fibroblasts and Wharton's jelly feeder layers.

PubMed

Parmar, Mehtab S; Mishra, Smruti Ranjan; Somal, Anjali; Pandey, Sriti; Kumar, G Sai; Sarkar, Mihir; Chandra, Vikash; Sharma, G Taru

2017-05-01

The present study examined the comparative expression and secretory profile of vital signaling molecules in buffalo fetal fibroblasts (BFF) and Wharton's jelly (BWJ) feeder layers at different passages. Both feeder layers were expanded up to 8th passage. Signaling molecules viz. bone morphogenetic protein 4 (BMP4), fibroblast growth factor 2 (FGF2), leukemia inhibitory factor (LIF) and transforming growth factor beta 1 (TGFB1) and pluripotency-associated transcriptional factors (POU5F1, SOX2, NANOG, KLF4, MYC and FOXD3) were immunolocalized in the both feeder types. A clear variation in the expression pattern of key signaling molecules with passaging was registered in both feeders compared to primary culture (0 passage). The conditioned media (CM) was collected from different passages (2, 4, 6, 8) of both the feeder layers and was quantified using enzyme-linked immunosorbent assay (ELISA). Concomitant to expression profile, protein quantification also revealed differences in the concentration of signaling molecules at different time points. Conjointly, expression and secretory profile revealed that 2nd passage of BFF and 6th passage of BWJ exhibit optimal levels of key signaling molecules thus may be selected as best passages for embryonic stem cells (ESCs) propagation. Further, the effect of mitomycin-C (MMC) treatment on the expression profile of signaling molecules in the selected passages of BFF and BWJ revealed that MMC modulates the expression profile of these molecules. In conclusion, the results indicate that feeder layers vary in expression and secretory pattern of vital signaling molecules with passaging. Based on these findings, the appropriate feeder passages may be selected for the quality propagation of buffalo ESCs. Copyright © 2017 Elsevier B.V. All rights reserved.

A probabilistic multi-criteria decision making technique for conceptual and preliminary aerospace systems design

NASA Astrophysics Data System (ADS)

Bandte, Oliver

It has always been the intention of systems engineering to invent or produce the best product possible. Many design techniques have been introduced over the course of decades that try to fulfill this intention. Unfortunately, no technique has succeeded in combining multi-criteria decision making with probabilistic design. The design technique developed in this thesis, the Joint Probabilistic Decision Making (JPDM) technique, successfully overcomes this deficiency by generating a multivariate probability distribution that serves in conjunction with a criterion value range of interest as a universally applicable objective function for multi-criteria optimization and product selection. This new objective function constitutes a meaningful Xnetric, called Probability of Success (POS), that allows the customer or designer to make a decision based on the chance of satisfying the customer's goals. In order to incorporate a joint probabilistic formulation into the systems design process, two algorithms are created that allow for an easy implementation into a numerical design framework: the (multivariate) Empirical Distribution Function and the Joint Probability Model. The Empirical Distribution Function estimates the probability that an event occurred by counting how many times it occurred in a given sample. The Joint Probability Model on the other hand is an analytical parametric model for the multivariate joint probability. It is comprised of the product of the univariate criterion distributions, generated by the traditional probabilistic design process, multiplied with a correlation function that is based on available correlation information between pairs of random variables. JPDM is an excellent tool for multi-objective optimization and product selection, because of its ability to transform disparate objectives into a single figure of merit, the likelihood of successfully meeting all goals or POS. The advantage of JPDM over other multi-criteria decision making techniques is that POS constitutes a single optimizable function or metric that enables a comparison of all alternative solutions on an equal basis. Hence, POS allows for the use of any standard single-objective optimization technique available and simplifies a complex multi-criteria selection problem into a simple ordering problem, where the solution with the highest POS is best. By distinguishing between controllable and uncontrollable variables in the design process, JPDM can account for the uncertain values of the uncontrollable variables that are inherent to the design problem, while facilitating an easy adjustment of the controllable ones to achieve the highest possible POS. Finally, JPDM's superiority over current multi-criteria decision making techniques is demonstrated with an optimization of a supersonic transport concept and ten contrived equations as well as a product selection example, determining an airline's best choice among Boeing's B-747, B-777, Airbus' A340, and a Supersonic Transport. The optimization examples demonstrate JPDM's ability to produce a better solution with a higher POS than an Overall Evaluation Criterion or Goal Programming approach. Similarly, the product selection example demonstrates JPDM's ability to produce a better solution with a higher POS and different ranking than the Overall Evaluation Criterion or Technique for Order Preferences by Similarity to the Ideal Solution (TOPSIS) approach.

Broadcasting satellite feeder links - Characteristics and planning

NASA Technical Reports Server (NTRS)

Kiebler, J. W.

1982-01-01

The paper presents the results of recent studies by the Feeder Link Sub-Working Group of the FCC Advisory Committee for the 1983 Regional Administrative Radio Conference (RARC). These studies conclude that specification of a few key parameters will make feeder link planning relatively straightforward. Feeder links can be located anywhere within a country if satellite orbit locations are separated by 10 deg for adjacent service areas and key parameter values presented in the paper are adopted. Colocated satellites serving a common service area need special attention to attain sufficient isolation between a desired channel and its adjacent cross-polarized channels and alternate co-polarized channels. In addition to presenting planning conclusions by the Advisory Committee, the paper presents and analyzes actions of the International Radio Consultative Committee's Conference Planning Meeting (CPM) concerning feeder links. The CPM reached conclusions similar to, and compatible with, those of the Advisory Committee.

Consequences of Feeder Delays for the Success of A380 Operations

NASA Technical Reports Server (NTRS)

Ruehle, Jens; Goetsch, Bjoern; Koch, Benjamin

2006-01-01

Due to existing slot and infrastructure constraints at international hub-and-spoke airports, an increase in feeder traffic seems only possible if larger feeder aircraft are used. Using a case study of Lufthansa German Airlines at Frankfurt International Airport, three possible A380 routes (Beijing, Tokyo-Narita, Los Angeles) were examined to assess the extent to which delays of feeder traffic may impact the economic performance of very large aircraft. On the basis of today s delays and anticipated traffic growth in the future, we found that between 9.5% and 13.5% of connecting passengers are unable to transfer to their respective intercontinental flights. In addition, the results demonstrate that a further increase in delays can be detrimental to the profitable operation of very large aircraft, as demonstrated by two out of three simulated routes. We suggest options for airlines operating very large aircraft to counteract the negative impacts of feeder delays.

Extraction and Analysis of Major Autumn Crops in Jingxian County Based on Multi - Temporal gf - 1 Remote Sensing Image and Object-Oriented

NASA Astrophysics Data System (ADS)

Ren, B.; Wen, Q.; Zhou, H.; Guan, F.; Li, L.; Yu, H.; Wang, Z.

2018-04-01

The purpose of this paper is to provide decision support for the adjustment and optimization of crop planting structure in Jingxian County. The object-oriented information extraction method is used to extract corn and cotton from Jingxian County of Hengshui City in Hebei Province, based on multi-period GF-1 16-meter images. The best time of data extraction was screened by analyzing the spectral characteristics of corn and cotton at different growth stages based on multi-period GF-116-meter images, phenological data, and field survey data. The results showed that the total classification accuracy of corn and cotton was up to 95.7 %, the producer accuracy was 96 % and 94 % respectively, and the user precision was 95.05 % and 95.9 % respectively, which satisfied the demand of crop monitoring application. Therefore, combined with multi-period high-resolution images and object-oriented classification can be a good extraction of large-scale distribution of crop information for crop monitoring to provide convenient and effective technical means.

Nematode diversity, abundance and community structure 50 years after the formation of the volcanic island of Surtsey

NASA Astrophysics Data System (ADS)

Ilieva-Makulec, K.; Bjarnadottir, B.; Sigurdsson, B. D.

2014-10-01

The soil nematode fauna can give important insights into soil development and other habitat changes that occur during primary succession. We investigated the generic composition, density, distribution and community structure of nematodes 50 years after the formation of a pristine volcanic island, Surtsey, Iceland. Part of the island has received additional nutrient inputs from seagulls breeding there since 1985, while the reminder has been much less affected and is at present found at a different successional sere. In total, 25 genera of nematodes were identified, of which 14 were reported on Surtsey for the first time. Nematode communities were more diverse in the more infertile area outside the gull colony, where 24 genera were found, compared to 18 inside. The trophic structure of the nematode communities showed relatively higher abundance of fungal feeders in the infertile areas, but relatively more bacterial- and plant-feeders inside the colony. Nematode abundance in surface soil was, however, significantly higher within the gull colony, with 16.7 ind. cm-2 compared to 3.6 ind. cm-2 outside. A multivariate analysis indicated that the nematode abundance and distribution on Surtsey were most strongly related to the soil C : N ratio, soil acidity, plant cover and biomass, soil temperature and soil depth.

Expressing Parallelism with ROOT

NASA Astrophysics Data System (ADS)

Piparo, D.; Tejedor, E.; Guiraud, E.; Ganis, G.; Mato, P.; Moneta, L.; Valls Pla, X.; Canal, P.

2017-10-01

The need for processing the ever-increasing amount of data generated by the LHC experiments in a more efficient way has motivated ROOT to further develop its support for parallelism. Such support is being tackled both for shared-memory and distributed-memory environments. The incarnations of the aforementioned parallelism are multi-threading, multi-processing and cluster-wide executions. In the area of multi-threading, we discuss the new implicit parallelism and related interfaces, as well as the new building blocks to safely operate with ROOT objects in a multi-threaded environment. Regarding multi-processing, we review the new MultiProc framework, comparing it with similar tools (e.g. multiprocessing module in Python). Finally, as an alternative to PROOF for cluster-wide executions, we introduce the efforts on integrating ROOT with state-of-the-art distributed data processing technologies like Spark, both in terms of programming model and runtime design (with EOS as one of the main components). For all the levels of parallelism, we discuss, based on real-life examples and measurements, how our proposals can increase the productivity of scientists.

Expressing Parallelism with ROOT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Piparo, D.; Tejedor, E.; Guiraud, E.

The need for processing the ever-increasing amount of data generated by the LHC experiments in a more efficient way has motivated ROOT to further develop its support for parallelism. Such support is being tackled both for shared-memory and distributed-memory environments. The incarnations of the aforementioned parallelism are multi-threading, multi-processing and cluster-wide executions. In the area of multi-threading, we discuss the new implicit parallelism and related interfaces, as well as the new building blocks to safely operate with ROOT objects in a multi-threaded environment. Regarding multi-processing, we review the new MultiProc framework, comparing it with similar tools (e.g. multiprocessing module inmore » Python). Finally, as an alternative to PROOF for cluster-wide executions, we introduce the efforts on integrating ROOT with state-of-the-art distributed data processing technologies like Spark, both in terms of programming model and runtime design (with EOS as one of the main components). For all the levels of parallelism, we discuss, based on real-life examples and measurements, how our proposals can increase the productivity of scientists.« less

Thermal imaging for assessment of electron-beam freeform fabrication (EBF3) additive manufacturing deposits

NASA Astrophysics Data System (ADS)

Zalameda, Joseph N.; Burke, Eric R.; Hafley, Robert A.; Taminger, Karen M.; Domack, Christopher S.; Brewer, Amy; Martin, Richard E.

2013-05-01

Additive manufacturing is a rapidly growing field where 3-dimensional parts can be produced layer by layer. NASA's electron beam freeform fabrication (EBF3) technology is being evaluated to manufacture metallic parts in a space environment. The benefits of EBF3 technology are weight savings to support space missions, rapid prototyping in a zero gravity environment, and improved vehicle readiness. The EBF3 system is composed of 3 main components: electron beam gun, multi-axis position system, and metallic wire feeder. The electron beam is used to melt the wire and the multi-axis positioning system is used to build the part layer by layer. To insure a quality deposit, a near infrared (NIR) camera is used to image the melt pool and solidification areas. This paper describes the calibration and application of a NIR camera for temperature measurement. In addition, image processing techniques are presented for deposit assessment metrics.

Rapid Fabricating Technique for Multi-Layered Human Hepatic Cell Sheets by Forceful Contraction of the Fibroblast Monolayer

PubMed Central

Sakai, Yusuke; Koike, Makiko; Hasegawa, Hideko; Yamanouchi, Kosho; Soyama, Akihiko; Takatsuki, Mitsuhisa; Kuroki, Tamotsu; Ohashi, Kazuo; Okano, Teruo; Eguchi, Susumu

2013-01-01

Cell sheet engineering is attracting attention from investigators in various fields, from basic research scientists to clinicians focused on regenerative medicine. However, hepatocytes have a limited proliferation potential in vitro, and it generally takes a several days to form a sheet morphology and multi-layered sheets. We herein report our rapid and efficient technique for generating multi-layered human hepatic cell (HepaRG® cell) sheets using pre-cultured fibroblast monolayers derived from human skin (TIG-118 cells) as a feeder layer on a temperature-responsive culture dish. Multi-layered TIG-118/HepaRG cell sheets with a thick morphology were harvested on day 4 of culturing HepaRG cells by forceful contraction of the TIG-118 cells, and the resulting sheet could be easily handled. In addition, the human albumin and alpha 1-antitrypsin synthesis activities of TIG-118/HepaRG cells were approximately 1.2 and 1.3 times higher than those of HepaRG cells, respectively. Therefore, this technique is considered to be a promising modality for rapidly fabricating multi-layered human hepatocyte sheets from cells with limited proliferation potential, and the engineered cell sheet could be used for cell transplantation with highly specific functions. PMID:23923035

Linear Power-Flow Models in Multiphase Distribution Networks: Preprint

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernstein, Andrey; Dall'Anese, Emiliano

This paper considers multiphase unbalanced distribution systems and develops approximate power-flow models where bus-voltages, line-currents, and powers at the point of common coupling are linearly related to the nodal net power injections. The linearization approach is grounded on a fixed-point interpretation of the AC power-flow equations, and it is applicable to distribution systems featuring (i) wye connections; (ii) ungrounded delta connections; (iii) a combination of wye-connected and delta-connected sources/loads; and, (iv) a combination of line-to-line and line-to-grounded-neutral devices at the secondary of distribution transformers. The proposed linear models can facilitate the development of computationally-affordable optimization and control applications -- frommore » advanced distribution management systems settings to online and distributed optimization routines. Performance of the proposed models is evaluated on different test feeders.« less

A digital protection system incorporating knowledge based learning

NASA Astrophysics Data System (ADS)

Watson, Karan; Russell, B. Don; McCall, Kurt

A digital system architecture used to diagnoses the operating state and health of electric distribution lines and to generate actions for line protection is presented. The architecture is described functionally and to a limited extent at the hardware level. This architecture incorporates multiple analysis and fault-detection techniques utilizing a variety of parameters. In addition, a knowledge-based decision maker, a long-term memory retention and recall scheme, and a learning environment are described. Preliminary laboratory implementations of the system elements have been completed. Enhanced protection for electric distribution feeders is provided by this system. Advantages of the system are enumerated.

Effects of bale feeder type and supplementation of monensin on hay waste, intake, and performance of beef cattle

USDA-ARS?s Scientific Manuscript database

The effects of feeder type and supplemental monensin on hay utilization in beef cows was investigated using 56 crossbred beef cows (BW= 494 ± 50 kg; BCS= 5.2 ± 0.5) in a split-plot treatment arrangement with a completely randomized design. Supplement treatment served as the main plot and feeder desi...

High pressure rotary piston coal feeder

NASA Technical Reports Server (NTRS)

Gardner, J. F.; Gencsoy, H. T.; Strimbeck, D. C.

1977-01-01

This feeder concept uniquely combines the functions of solids feeding, metering, and pressurization into one compact system. Success with the rotary-piston concept would provide a lower-cost alternative to lock-hopper systems. The design of the feeder is presented, with special emphasis on the difficult problem of seal design. Initial tests will be to check seal performance. Subsequent tests will evaluate solids-feeding ability.

Low Spillage Metabolic Feeder

NASA Technical Reports Server (NTRS)

Evans, JuliAnn (Inventor); Gundo, Daniel P. (Inventor); Harper, Jennifer S. (Inventor); Mulenburg, Gerald M. (Inventor); Skundberg, Thomas L. (Inventor)

1996-01-01

An animal feeder for use in a metabolic cage is introduced. The feeder includes a confined passageway and an adjustable notched gate proceeding a food cup. The gate is adjusted so that the entry area to the food cup approximates the cross sectional head area of the animal. Food ejected from the food cup by a caged animal is dropped through a grate into a spill tray.

7 CFR 1230.113 - Collection and remittance of assessments for the sale of feeder pigs and market hogs.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 10 2011-01-01 2011-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...

7 CFR 1230.113 - Collection and remittance of assessments for the sale of feeder pigs and market hogs.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 10 2014-01-01 2014-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...

7 CFR 1230.113 - Collection and remittance of assessments for the sale of feeder pigs and market hogs.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 10 2012-01-01 2012-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...

7 CFR 1230.113 - Collection and remittance of assessments for the sale of feeder pigs and market hogs.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 10 2013-01-01 2013-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...

7 CFR 1230.113 - Collection and remittance of assessments for the sale of feeder pigs and market hogs.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Collection and remittance of assessments for the sale of feeder pigs and market hogs. 1230.113 Section 1230.113 Agriculture Regulations of the Department... pigs and market hogs. Pursuant to the provisions of § 1230.71, purchasers of feeder pigs or market hogs...

Postmitotic human dermal fibroblasts preserve intact feeder properties for epithelial cell growth after long-term cryopreservation.

PubMed

Limat, A; Hunziker, T; Boillat, C; Noser, F; Wiesmann, U

1990-07-01

In vitro, human dermal fibroblasts (HDF) differentiate through morphologically and biochemically identified compartments. In the course of this spontaneous differentiation through mitotic and postmitotic states, a tremendous increase in cellular and nuclear size occurs. Induction of postmitotic states can be accelerated by chemical (e.g., mitomycin C) or physical (e.g., x-ray) treatments. Such experimentally induced postmitotic HDF cells support very efficiently the growth of cutaneous epithelial cells, i.e. interfollicular keratinocytes and follicular outer root sheath cells, especially in primary cultures starting from very low cell seeding densities. The HDF feeder system provides more fundamental and also practical advantages, i.e. use of initially diploid human fibroblasts from known anatomic locations, easy handling and excellent reproducibility, and the possibility of long-term storage by incubation at 37 degrees C. Conditions for the cryogenic storage of postmitotic HDF cells in liquid nitrogen are presented and related to the feeder capacity for epithelial cell growth. Because postmitotic HDF cells preserve intact feeder properties after long-term storage, the immediate availability of feeder cells and the possibility to repeat experiments with identical materials further substantiate the usefulness of this feeder system.

Assessing the role of benthic filter feeders on phytoplankton production in a shellfish farming site: Mont Saint Michel Bay, France

NASA Astrophysics Data System (ADS)

Cugier, Philippe; Struski, Caroline; Blanchard, Michel; Mazurié, Joseph; Pouvreau, Stéphane; Olivier, Frédéric; Trigui, Jihane R.; Thiébaut, Eric

2010-07-01

The macrobenthic community of Mont Saint Michel Bay (English Channel, France) is mainly dominated by filter feeders, including cultivated species (oysters and mussels). An ecological model of the bay was developed, coupling a 2D hydro-sedimentary model and two biological models for primary production and filter-feeder filtration. The filter-feeder model includes three cultivated species ( Mytilus edulis, Crassostrea gigas and Ostrea edulis), one invasive species ( Crepidula fornicata) and eight wild native species ( Abra alba, Cerastoderma edule, Glycymeris glycymeris, Lanice conchilega, Macoma balthica, Paphia rhomboides, Sabellaria alveolata, andSpisula ovalis). For cultivated and invasive species, the production of biodeposits was computed to assess their role in restimulating primary production. Chlorophyll a concentrations appeared to be strongly controlled by the filter feeders. When the pressure of each benthic compartment on phytoplankton was estimated separately wild species and the invasive slipper limpet C.fornicata were shown to be key elements in the control of primary production. Conversely, the role of cultivated species, particularly oysters, was weaker. Feedback due to the mineralization of biodeposits also appears to be crucial to fully evaluate the role of filter feeders in primary production.

Power Hardware-in-the-Loop (PHIL) Testing Facility for Distributed Energy Storage (Poster)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neubauer.J.; Lundstrom, B.; Simpson, M.

2014-06-01

The growing deployment of distributed, variable generation and evolving end-user load profiles presents a unique set of challenges to grid operators responsible for providing reliable and high quality electrical service. Mass deployment of distributed energy storage systems (DESS) has the potential to solve many of the associated integration issues while offering reliability and energy security benefits other solutions cannot. However, tools to develop, optimize, and validate DESS control strategies and hardware are in short supply. To fill this gap, NREL has constructed a power hardware-in-the-loop (PHIL) test facility that connects DESS, grid simulator, and load bank hardware to a distributionmore » feeder simulation.« less

Impact of electric vehicles on the IEEE 34 node distribution infrastructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, Zeming; Shalalfel, Laith; Beshir, Mohammed J.

With the growing penetration of the electric vehicles to our daily life owing to their economic and environmental benefits, there will be both opportunities and challenges to the utilities when adopting plug-in electric vehicles (PEV) to the distribution network. In this study, a thorough analysis based on real-world project is conducted to evaluate the impacts of electric vehicles infrastructure on the grid relating to system load flow, load factor, and voltage stability. IEEE 34 node test feeder was selected and tested along with different case scenarios utilizing the electrical distribution design (EDD) software to find out the potential impacts tomore » the grid.« less

Impact of electric vehicles on the IEEE 34 node distribution infrastructure

DOE PAGES

Jiang, Zeming; Shalalfel, Laith; Beshir, Mohammed J.

2014-10-01

With the growing penetration of the electric vehicles to our daily life owing to their economic and environmental benefits, there will be both opportunities and challenges to the utilities when adopting plug-in electric vehicles (PEV) to the distribution network. In this study, a thorough analysis based on real-world project is conducted to evaluate the impacts of electric vehicles infrastructure on the grid relating to system load flow, load factor, and voltage stability. IEEE 34 node test feeder was selected and tested along with different case scenarios utilizing the electrical distribution design (EDD) software to find out the potential impacts tomore » the grid.« less

Study of dispersed small wind systems interconnected with a utility distribution system

NASA Astrophysics Data System (ADS)

Curtice, D.; Patton, J.; Bohn, J.; Sechan, N.

1980-03-01

Operating problems for various penetrations of small wind systems connected to the distribution system on a utility are defined. Protection equipment, safety hazards, feeder voltage regulation, line losses, and voltage flicker problems are studied, assuming different small wind systems connected to an existing distribution system. To identify hardware deficiencies, possible solutions provided by off-the-shelf hardware and equipment are assessed. Results of the study indicate that existing techniques are inadequate for detecting isolated operation of a small wind system. Potential safety hazards posed by small wind systems are adequately handled by present work procedures although these procedures require a disconnect device at synchronous generator and self commutated inverter small wind systems.

Evaluation and Management of Neonatal Dysphagia: Impact of Pharyngoesophageal Motility Studies and Multidisciplinary Feeding Strategy

PubMed Central

Jadcherla, Sudarshan R.; Stoner, Erin; Gupta, Alankar; Bates, D. Gregory; Fernandez, Soledad; Di Lorenzo, Carlo; Linscheid, Thomas

2013-01-01

Background and objectives Abnormal swallowing (dysphagia) among neonates is commonly evaluated using the videofluoroscopic swallow study (VSS). Radiological findings considered high risk for administration of oral feeding include nasopharyngeal reflux, laryngeal penetration, aspiration, or pooling. Our aims were to determine pharyngoesophageal motility correlates in neonates with dysphagia and the impact of multidisciplinary feeding strategy. Methods Twenty dysphagic neonates (mean gestation ± standard deviation [SD] = 30.9 ± 4.9 weeks; median 31.1 weeks; range = 23.7–38.6 weeks) with abnormal VSS results were evaluated at 49.9 ± 16.5 weeks (median 41.36 weeks) postmenstrual age. The subjects underwent a swallow-integrated pharyngoesophageal motility assessment of basal and adaptive swallowing reflexes using a micromanometry catheter and pneumohydraulic water perfusion system. Based on observations during the motility study, multidisciplinary feeding strategies were applied and included postural adaptation, sensory modification, hunger manipulation, and operant conditioning methods. To discriminate pharyngoesophageal manometry correlates between oral feeders and tube feeders, data were stratified based on the primary feeding method at discharge, oral feeding versus tube feeding. Results At discharge, 15 of 20 dysphagic neonates achieved oral feeding success, and the rest required chronic tube feeding. Pharyngoesophageal manometry correlates were significantly different (P <0.05) between the primary oral feeders versus the chronic tube feeders for swallow frequency, swallow propagation, presence of adaptive peristaltic reflexes, oral feeding challenge test results, and upper esophageal sphincter tone. VSS results or disease characteristics had little effect on the feeding outcomes (P = NS). Conclusions Swallow-integrated esophageal motility studies permit prolonged evaluation of swallowing reflexes and responses to stimuli under controlled conditions at cribside. The dysfunctional neuromotor mechanisms may be responsible for neonatal dysphagia or its consequences. Manometry may be a better predictor than VSS in identifying patients who are likely to succeed in vigorous intervention programs. PMID:19179881

Multi-metric calibration of hydrological model to capture overall flow regimes

NASA Astrophysics Data System (ADS)

Zhang, Yongyong; Shao, Quanxi; Zhang, Shifeng; Zhai, Xiaoyan; She, Dunxian

2016-08-01

Flow regimes (e.g., magnitude, frequency, variation, duration, timing and rating of change) play a critical role in water supply and flood control, environmental processes, as well as biodiversity and life history patterns in the aquatic ecosystem. The traditional flow magnitude-oriented calibration of hydrological model was usually inadequate to well capture all the characteristics of observed flow regimes. In this study, we simulated multiple flow regime metrics simultaneously by coupling a distributed hydrological model with an equally weighted multi-objective optimization algorithm. Two headwater watersheds in the arid Hexi Corridor were selected for the case study. Sixteen metrics were selected as optimization objectives, which could represent the major characteristics of flow regimes. Model performance was compared with that of the single objective calibration. Results showed that most metrics were better simulated by the multi-objective approach than those of the single objective calibration, especially the low and high flow magnitudes, frequency and variation, duration, maximum flow timing and rating. However, the model performance of middle flow magnitude was not significantly improved because this metric was usually well captured by single objective calibration. The timing of minimum flow was poorly predicted by both the multi-metric and single calibrations due to the uncertainties in model structure and input data. The sensitive parameter values of the hydrological model changed remarkably and the simulated hydrological processes by the multi-metric calibration became more reliable, because more flow characteristics were considered. The study is expected to provide more detailed flow information by hydrological simulation for the integrated water resources management, and to improve the simulation performances of overall flow regimes.

Multi-objects recognition for distributed intelligent sensor networks

NASA Astrophysics Data System (ADS)

He, Haibo; Chen, Sheng; Cao, Yuan; Desai, Sachi; Hohil, Myron E.

2008-04-01

This paper proposes an innovative approach for multi-objects recognition for homeland security and defense based intelligent sensor networks. Unlike the conventional way of information analysis, data mining in such networks is typically characterized with high information ambiguity/uncertainty, data redundancy, high dimensionality and real-time constrains. Furthermore, since a typical military based network normally includes multiple mobile sensor platforms, ground forces, fortified tanks, combat flights, and other resources, it is critical to develop intelligent data mining approaches to fuse different information resources to understand dynamic environments, to support decision making processes, and finally to achieve the goals. This paper aims to address these issues with a focus on multi-objects recognition. Instead of classifying a single object as in the traditional image classification problems, the proposed method can automatically learn multiple objectives simultaneously. Image segmentation techniques are used to identify the interesting regions in the field, which correspond to multiple objects such as soldiers or tanks. Since different objects will come with different feature sizes, we propose a feature scaling method to represent each object in the same number of dimensions. This is achieved by linear/nonlinear scaling and sampling techniques. Finally, support vector machine (SVM) based learning algorithms are developed to learn and build the associations for different objects, and such knowledge will be adaptively accumulated for objects recognition in the testing stage. We test the effectiveness of proposed method in different simulated military environments.

High precision during food recruitment of experienced (reactivated) foragers in the stingless bee Scaptotrigona mexicana (Apidae, Meliponini)

NASA Astrophysics Data System (ADS)

Sánchez, Daniel; Nieh, James C.; Hénaut, Yann; Cruz, Leopoldo; Vandame, Rémy

Several studies have examined the existence of recruitment communication mechanisms in stingless bees. However, the spatial accuracy of location-specific recruitment has not been examined. Moreover, the location-specific recruitment of reactivated foragers, i.e., foragers that have previously experienced the same food source at a different location and time, has not been explicitly examined. However, such foragers may also play a significant role in colony foraging, particularly in small colonies. Here we report that reactivated Scaptotrigona mexicana foragers can recruit with high precision to a specific food location. The recruitment precision of reactivated foragers was evaluated by placing control feeders to the left and the right of the training feeder (direction-precision tests) and between the nest and the training feeder and beyond it (distance-precision tests). Reactivated foragers arrived at the correct location with high precision: 98.44% arrived at the training feeder in the direction trials (five-feeder fan-shaped array, accuracy of at least +/-6° of azimuth at 50 m from the nest), and 88.62% arrived at the training feeder in the distance trials (five-feeder linear array, accuracy of at least +/-5 m or +/-10% at 50 m from the nest). Thus, S. mexicana reactivated foragers can find the indicated food source at a specific distance and direction with high precision, higher than that shown by honeybees, Apis mellifera, which do not communicate food location at such close distances to the nest.

Number of hummingbird visits determines flower mite abundance on hummingbird feeders.

PubMed

Márquez-Luna, Ubaldo; Vázquez González, María Magdalena; Castellanos, Ignacio; Ortiz-Pulido, Raúl

2016-08-01

Members of several genera of mites from the family Melicharidae (Mesostigmata) use hummingbirds as transport host to move from flower to flower, where they feed on pollen and nectar. The factors that influence hummingbird flower mite abundance on host plant flowers are not currently known. Here we tested whether hummingbird flower mite abundance on an artificial nectar source is determined by number of hummingbird visits, nectar energy content or species richness of visiting hummingbirds. We conducted experiments employing hummingbird feeders with sucrose solutions of low, medium, and high energy concentrations, placed in a xeric shrubland. In the first experiment, we recorded the number of visiting hummingbirds and the number of visiting hummingbird species, as well as the abundance of hummingbird flower mites on each feeder. Feeders with the highest sucrose concentration had the most hummingbird visits and the highest flower mite abundances; however, there was no significant effect of hummingbird species richness on mite abundance. In the second experiment, we recorded flower mite abundance on feeders after we standardized the number of hummingbird visits to them. Abundance of flower mites did not differ significantly between feeders when we controlled for hummingbird visits. Our results suggest that nectar energy concentration determines hummingbird visits, which in turn determines flower mite abundance in our feeders. Our results do not support the hypothesis that mites descend from hummingbird nostrils more on richer nectar sources; however, it does not preclude the possibility that flower mites select for nectar concentration at other spatial and temporal scales.

Simultaneous identification of optical constants and PSD of spherical particles by multi-wavelength scattering-transmittance measurement

NASA Astrophysics Data System (ADS)

Zhang, Jun-You; Qi, Hong; Ren, Ya-Tao; Ruan, Li-Ming

2018-04-01

An accurate and stable identification technique is developed to retrieve the optical constants and particle size distributions (PSDs) of particle system simultaneously from the multi-wavelength scattering-transmittance signals by using the improved quantum particle swarm optimization algorithm. The Mie theory are selected to calculate the directional laser intensity scattered by particles and the spectral collimated transmittance. The sensitivity and objective function distribution analysis were conducted to evaluate the mathematical properties (i.e. ill-posedness and multimodality) of the inverse problems under three different optical signals combinations (i.e. the single-wavelength multi-angle light scattering signal, the single-wavelength multi-angle light scattering and spectral transmittance signal, and the multi-angle light scattering and spectral transmittance signal). It was found the best global convergence performance can be obtained by using the multi-wavelength scattering-transmittance signals. Meanwhile, the present technique have been tested under different Gaussian measurement noise to prove its feasibility in a large solution space. All the results show that the inverse technique by using multi-wavelength scattering-transmittance signals is effective and suitable for retrieving the optical complex refractive indices and PSD of particle system simultaneously.

47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

Code of Federal Regulations, 2012 CFR

2012-10-01

.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...

47 CFR 25.257 - Special requirements for operations in the band 29.1-29.25 GHz between NGSO MSS and LMDS.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...

47 CFR 25.257 - Special requirements for operations in the band 29.1-29.25 GHz between NGSO MSS and LMDS.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...

47 CFR 25.257 - Special requirements for operations in the band 29.1-29.25 GHz between NGSO MSS and LMDS.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...

47 CFR 25.257 - Special requirements for operations in the band 29.1-29.25 GHz between NGSO MSS and LMDS.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...

47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

Code of Federal Regulations, 2011 CFR

2011-10-01

.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...

47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

Code of Federal Regulations, 2013 CFR

2013-10-01

.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...

47 CFR 25.223 - Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS.

Code of Federal Regulations, 2013 CFR

2013-10-01

... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...

47 CFR 25.223 - Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS.

Code of Federal Regulations, 2011 CFR

2011-10-01

... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...

47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

Code of Federal Regulations, 2010 CFR

2010-10-01

.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...

47 CFR 25.223 - Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS.

Code of Federal Regulations, 2012 CFR

2012-10-01

... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...

47 CFR 25.258 - Sharing between NGSO MSS Feeder links Stations and GSO FSS services in the 29.25-29.5 GHz Bands.

Code of Federal Regulations, 2014 CFR

2014-10-01

.... (a) Operators of NGSO MSS feeder link earth stations and GSO FSS earth stations in the band 29.25 to... MSS feeder link earth station complexes, that will minimize instances of unacceptable interference to the GSO FSS space stations. Earth station licensees operating with GSO FSS systems shall be capable of...

47 CFR 25.257 - Special requirements for operations in the band 29.1-29.25 GHz between NGSO MSS and LMDS.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Earth-to-space transmissions from feeder link earth station complexes. A “feeder link earth station complex” may include up to three (3) earth station groups, with each earth station group having up to four... NGSO MSS licensees or applicants pursuant to § 101.147. (b) A maximum of seven (7) feeder link earth...

47 CFR 25.223 - Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS.

Code of Federal Regulations, 2010 CFR

2010-10-01

... feeder link earth stations in the 17/24 GHz BSS. 25.223 Section 25.223 Telecommunication FEDERAL....223 Off-axis EIRP spectral density limits for feeder link earth stations in the 17/24 GHz BSS. (a) This section applies to all applications for earth station licenses in the 17/24 GHz BSS frequency...

The Effects of a Modified Treatment Package with and without Feeder Modeling on One Child's Acceptance of Novel Foods

ERIC Educational Resources Information Center

Seiverling, Laura; Harclerode, Whitney; Williams, Keith

2014-01-01

The purpose of this study was to examine if sequential presentation with feeder modeling would lead to an increase in bites accepted of new foods compared to sequential presentation without feeder modeling in a typically developing 4-year-old boy with food selectivity. The participant's acceptance of novel foods increased both in the modeling and…

Multi-Objective Random Search Algorithm for Simultaneously Optimizing Wind Farm Layout and Number of Turbines

NASA Astrophysics Data System (ADS)

Feng, Ju; Shen, Wen Zhong; Xu, Chang

2016-09-01

A new algorithm for multi-objective wind farm layout optimization is presented. It formulates the wind turbine locations as continuous variables and is capable of optimizing the number of turbines and their locations in the wind farm simultaneously. Two objectives are considered. One is to maximize the total power production, which is calculated by considering the wake effects using the Jensen wake model combined with the local wind distribution. The other is to minimize the total electrical cable length. This length is assumed to be the total length of the minimal spanning tree that connects all turbines and is calculated by using Prim's algorithm. Constraints on wind farm boundary and wind turbine proximity are also considered. An ideal test case shows the proposed algorithm largely outperforms a famous multi-objective genetic algorithm (NSGA-II). In the real test case based on the Horn Rev 1 wind farm, the algorithm also obtains useful Pareto frontiers and provides a wide range of Pareto optimal layouts with different numbers of turbines for a real-life wind farm developer.

MONSS: A multi-objective nonlinear simplex search approach

NASA Astrophysics Data System (ADS)

Zapotecas-Martínez, Saúl; Coello Coello, Carlos A.

2016-01-01

This article presents a novel methodology for dealing with continuous box-constrained multi-objective optimization problems (MOPs). The proposed algorithm adopts a nonlinear simplex search scheme in order to obtain multiple elements of the Pareto optimal set. The search is directed by a well-distributed set of weight vectors, each of which defines a scalarization problem that is solved by deforming a simplex according to the movements described by Nelder and Mead's method. Considering an MOP with n decision variables, the simplex is constructed using n+1 solutions which minimize different scalarization problems defined by n+1 neighbor weight vectors. All solutions found in the search are used to update a set of solutions considered to be the minima for each separate problem. In this way, the proposed algorithm collectively obtains multiple trade-offs among the different conflicting objectives, while maintaining a proper representation of the Pareto optimal front. In this article, it is shown that a well-designed strategy using just mathematical programming techniques can be competitive with respect to the state-of-the-art multi-objective evolutionary algorithms against which it was compared.

Energy Technology Allocation for Distributed Energy Resources: A Technology-Policy Framework

NASA Astrophysics Data System (ADS)

Mallikarjun, Sreekanth

Distributed energy resources (DER) are emerging rapidly. New engineering technologies, materials, and designs improve the performance and extend the range of locations for DER. In contrast, constructing new or modernizing existing high voltage transmission lines for centralized generation are expensive and challenging. In addition, customer demand for reliability has increased and concerns about climate change have created a pull for swift renewable energy penetration. In this context, DER policy makers, developers, and users are interested in determining which energy technologies to use to accommodate different end-use energy demands. We present a two-stage multi-objective strategic technology-policy framework for determining the optimal energy technology allocation for DER. The framework simultaneously considers economic, technical, and environmental objectives. The first stage utilizes a Data Envelopment Analysis model for each end-use to evaluate the performance of each energy technology based on the three objectives. The second stage incorporates factor efficiencies determined in the first stage, capacity limitations, dispatchability, and renewable penetration for each technology, and demand for each end-use into a bottleneck multi-criteria decision model which provides the Pareto-optimal energy resource allocation. We conduct several case studies to understand the roles of various distributed energy technologies in different scenarios. We construct some policy implications based on the model results of set of case studies.

Distributed learning and multi-objectivity in traffic light control

NASA Astrophysics Data System (ADS)

Brys, Tim; Pham, Tong T.; Taylor, Matthew E.

2014-01-01

Traffic jams and suboptimal traffic flows are ubiquitous in modern societies, and they create enormous economic losses each year. Delays at traffic lights alone account for roughly 10% of all delays in US traffic. As most traffic light scheduling systems currently in use are static, set up by human experts rather than being adaptive, the interest in machine learning approaches to this problem has increased in recent years. Reinforcement learning (RL) approaches are often used in these studies, as they require little pre-existing knowledge about traffic flows. Distributed constraint optimisation approaches (DCOP) have also been shown to be successful, but are limited to cases where the traffic flows are known. The distributed coordination of exploration and exploitation (DCEE) framework was recently proposed to introduce learning in the DCOP framework. In this paper, we present a study of DCEE and RL techniques in a complex simulator, illustrating the particular advantages of each, comparing them against standard isolated traffic actuated signals. We analyse how learning and coordination behave under different traffic conditions, and discuss the multi-objective nature of the problem. Finally we evaluate several alternative reward signals in the best performing approach, some of these taking advantage of the correlation between the problem-inherent objectives to improve performance.

Surrogate Based Uni/Multi-Objective Optimization and Distribution Estimation Methods

NASA Astrophysics Data System (ADS)

Gong, W.; Duan, Q.; Huo, X.

2017-12-01

Parameter calibration has been demonstrated as an effective way to improve the performance of dynamic models, such as hydrological models, land surface models, weather and climate models etc. Traditional optimization algorithms usually cost a huge number of model evaluations, making dynamic model calibration very difficult, or even computationally prohibitive. With the help of a serious of recently developed adaptive surrogate-modelling based optimization methods: uni-objective optimization method ASMO, multi-objective optimization method MO-ASMO, and probability distribution estimation method ASMO-PODE, the number of model evaluations can be significantly reduced to several hundreds, making it possible to calibrate very expensive dynamic models, such as regional high resolution land surface models, weather forecast models such as WRF, and intermediate complexity earth system models such as LOVECLIM. This presentation provides a brief introduction to the common framework of adaptive surrogate-based optimization algorithms of ASMO, MO-ASMO and ASMO-PODE, a case study of Common Land Model (CoLM) calibration in Heihe river basin in Northwest China, and an outlook of the potential applications of the surrogate-based optimization methods.

Effect of concentrate feeder design on performance, eating and animal behavior, welfare, ruminal health, and carcass quality in Holstein bulls fed high-concentrate diets.

PubMed

Verdú, M; Bach, A; Devant, M

2015-06-01

A total of 240 Holstein bulls (121 ± 2.0 kg initial BW; 99 ± 1.0 d of age), from 2 consecutive fattening cycles, were randomly allocated in 1 of 6 pens and assigned to 1 of the 3 treatments consisting of different concentrate feeder designs: a control feeder with 4 feeding spaces (CF), a feeder with less concentrate capacity (CFL), and a single-space feeder with lateral protections (SF). Each pen had a straw feeder and a drinker. All animals were fed a high-concentrate diet for ad libitum intake. Concentrate consumption was recorded daily using a computerized feeder, straw consumption was recorded weekly, and BW was recorded every 14 d. Animal behavior was registered on d 1, 3, 5, 8, and 14 and every 28 d by scan sampling. Eating behavior at concentrate feeders was filmed on d 12, 125, and 206. On d 7, 120, and 204, samples of rumen contents were collected for measurement of pH and VFA and blood samples were obtained to analyze NEFA, haptoglobin, glucose, and insulin. Animals were slaughtered after 223 d, and HCW and lesions of the rumen wall and liver were recorded. The accumulative concentrate consumption per animal tended (P = 0.09) to be greater with CF than with CFL and SF. Also, CV of concentrate consumption was greater (P < 0.01) for SF than for CF or CFL. However, feeder design did not influence the other performance and carcass data. Also, no differences among treatments in rumen wall evaluation and liver abscesses were observed. At 7 and 204 d of study, SF bulls had greater (P < 0.05) rumen pH compared with CF and CFL bulls. On d 7, the acetate to propionate ratio from SF was greater (P < 0.05) than for CFL or CF. At d 7, NEFA of SF were greater (P < 0.05) compared with CF and CFL. Bulls fed with CF have the greatest (P < 0.01) concentrate disappearance velocity followed by bulls fed with CFL and finally by bulls fed with SF, and this was associated with different feeding behaviors. Bulls on SF spent more time (P < 0.05) eating straw and exhibited fewer (P < 0.05) displacements at concentrate feeder than CF and CFL bulls. The CFL bulls exhibited (P < 0.01) more attempted mounts and tended (P = 0.10) to exhibit more completed mounts than CF bulls. In conclusion, both alternative feeder designs (CFL and SF) are good strategies to reduce total concentrate consumption without impairing performance, rumen health, or animal welfare in Holstein bulls fed high-concentrate diets. However, at the beginning, there was evidence that animals fed using SF had problems with adaptation.

Effect of feeder space during the growing and laying periods and the rate of feed increase at the onset of lay on broiler breeder female reproductive function.

PubMed

Leksrisompong, N; Romero-Sanchez, H; Oviedo-Rondón, E O; Brake, J

2014-07-01

A study was conducted to examine how 2 feeder space allocations during the rearing period followed by 2 feeder space allocations after photostimulation and 2 female feeding to peak programs (fast or slow) affected female broiler breeder reproductive performance and mortality. Sixteen pens of 76 breeder females each were equipped with either 4 tube feeders with a 132 cm circumference pan (7.0 cm/female) or 6 feeders (10.4 cm/female) to 21 wk of age. Thereafter, 64 females were moved to breeding pens, photostimulated, and fed sex-separate from either 3 (6.2 cm/female) or 5 (10.3 cm/female) feeders with either fast or slow feeding to peak feeding programs applied to complete a 2 × 2 × 2 factorial design. Seven males that were separately reared in a similar manner were added per pen. Individual female BW was determined at 6, 20, and 32 wk of age and BW uniformity assessed. Greater feeder space during rearing increased BW at 32 wk of age, whereas greater feeder space during lay or slow feeding to peak decreased BW at 32 wk. There were no differences in BW uniformity. Hens from the 10.4 to 10.3 cm/female combination produced a significantly greater number of eggs as compared with the 7.0 to 10.3 cm/female and 10.4 to 6.2 cm/female combinations with the 7.0 to 6.2 cm/female combination intermediate. Percentage hen-day egg production of the 10.4 to 10.3 cm/female combination hens was significantly greater than all other combinations. Livability was improved in the 10.4 to 10.3 cm/female combination relative to the 7.0 to 10.3 cm/female combination with the others intermediate. The fast feeding to peak program increased yolk weight as well as yolk:albumen ratio at 28 and 30 wk of age, but egg weight did not differ. These data indicated that increased or decreased feeder space between the growing and laying periods did not affect broiler breeder female BW, uniformity, egg weight, fertility, or hatchability. The 10.3 cm/female laying feeder space exhibited the best hen-day egg production in combination with 10.4 cm/pullet rearing but not with 7.0 cm/pullet rearing space. In a similar manner, hen mortality was greater in the 7.0 to 10.3 cm/female feeder space combination that the 10.4 to 10.3 cm/female combination. © 2014 Poultry Science Association Inc.

Optical ground station optimization for future optical geostationary satellite feeder uplinks

NASA Astrophysics Data System (ADS)

Camboulives, A.-R.; Velluet, M.-T.; Poulenard, S.; Saint-Antonin, L.; Michau, V.

2017-02-01

An optical link based on a multiplex of wavelengths at 1:55 μm is foreseen to be a valuable alternative to the conventional radio-frequencies for the feeder link of the next-generation of high throughput geostationary satellite. Considering the limited power of lasers envisioned for feeder links, the beam divergence has to be dramatically reduced. Consequently, the beam pointing becomes a key issue. During its propagation between the ground station and a geostationary satellite, the optical beam is deflected (beam wandering), and possibly distorted (beam spreading), by atmospheric turbulence. It induces strong fluctuations of the detected telecom signal, thus increasing the bit error rate (BER). A steering mirror using a measurement from a beam coming from the satellite is used to pre-compensate the deflection. Because of the point-ahead angle between the downlink and the uplink, the turbulence effects experienced by both beams are slightly different, inducing an error in the correction. This error is characterized as a function of the turbulence characteristics as well as of the terminal characteristics, such as the servo-loop bandwidth or the beam diameter, and is included in the link budget. From this result, it is possible to predict intensity fluctuations detected by the satellite statistically (mean intensity, scintillation index, probability of fade, etc.)). The final objective is to optimize the different parameters of an optical ground station capable of mitigating the impact of atmospheric turbulence on the uplink in order to be compliant with the targeted capacity (1Terabit/s by 2025).

A multi-institutional approach to delivering shared curricula for developing a next-generation energy workforce

DOE PAGES

Holloway, Lawrence E.; Qu, Zhihua; Mohr-Schroeder, Margaret J.; ...

2017-02-06

In this study, we consider collaborative power systems education through the FEEDER consortium. To increase students' access to power engineering educational content, the consortium of seven universities was formed. A framework is presented to characterize different collaborative education activities among the universities. Three of these approaches of collaborative educational activities are presented and discussed. These include 1) cross-institutional blended courses ("MS-MD''); 2) cross-institutional distance courses ("SS-MD''); and 3) single-site special experiential courses and concentrated on-site programs available to students across consortium institutions ("MS-SD''). As a result, this paper presents the advantages and disadvantages of each approach.

A Novel Reliable WDM-PON System

NASA Astrophysics Data System (ADS)

Chen, Benyang; Gan, Chaoqin; Qi, Yongqian; Xia, Lei

2011-12-01

In this paper, a reliable Wavelength-Division-Multiplexing Passive Optical Network (WDM-PON) system is proposed. It can provide the protection against both the feeder fiber failure and the distribution fiber failure. When the fiber failure occurs, the corresponding switches in the OLT and in the ONU can switch to the protection link without affecting the users in normal status. That is to say, the protection for one ONU is independent of the other ONUs.

Dynamic simulation of Static Var Compensators in distribution systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Koessler, R.J.

1992-08-01

This paper is a system study guide for the correction of voltage dips due to large motor startups with Static Var Compensators (SVCs). The method utilizes time simulations, which are an important aid in the equipment design and specification. The paper illustrates the process of setting-up a computer model and performing time simulations. The study process is demonstrated through an example, the Shawnee feeder in the Niagara Mohawk Power Corporation service area.

Analysis of Feeder Bus Network Design and Scheduling Problems

PubMed Central

Almasi, Mohammad Hadi; Karim, Mohamed Rehan

2014-01-01

A growing concern for public transit is its inability to shift passenger's mode from private to public transport. In order to overcome this problem, a more developed feeder bus network and matched schedules will play important roles. The present paper aims to review some of the studies performed on Feeder Bus Network Design and Scheduling Problem (FNDSP) based on three distinctive parts of the FNDSP setup, namely, problem description, problem characteristics, and solution approaches. The problems consist of different subproblems including data preparation, feeder bus network design, route generation, and feeder bus scheduling. Subsequently, descriptive analysis and classification of previous works are presented to highlight the main characteristics and solution methods. Finally, some of the issues and trends for future research are identified. This paper is targeted at dealing with the FNDSP to exhibit strategic and tactical goals and also contributes to the unification of the field which might be a useful complement to the few existing reviews. PMID:24526890

Establishment of feeder-free culture system for human induced pluripotent stem cell on DAS nanocrystalline graphene

NASA Astrophysics Data System (ADS)

Lee, Hyunah; Nam, Donggyu; Choi, Jae-Kyung; Araúzo-Bravo, Marcos J.; Kwon, Soon-Yong; Zaehres, Holm; Lee, Taehee; Park, Chan Young; Kang, Hyun-Wook; Schöler, Hans R.; Kim, Jeong Beom

2016-02-01

The maintenance of undifferentiated human pluripotent stem cells (hPSC) under xeno-free condition requires the use of human feeder cells or extracellular matrix (ECM) coating. However, human-derived sources may cause human pathogen contamination by viral or non-viral agents to the patients. Here we demonstrate feeder-free and xeno-free culture system for hPSC expansion using diffusion assisted synthesis-grown nanocrystalline graphene (DAS-NG), a synthetic non-biological nanomaterial which completely rule out the concern of human pathogen contamination. DAS-NG exhibited advanced biocompatibilities including surface nanoroughness, oxygen containing functional groups and hydrophilicity. hPSC cultured on DAS-NG could maintain pluripotency in vitro and in vivo, and especially cell adhesion-related gene expression profile was comparable to those of cultured on feeders, while hPSC cultured without DAS-NG differentiated spontaneously with high expression of somatic cell-enriched adhesion genes. This feeder-free and xeno-free culture method using DAS-NG will facilitate the generation of clinical-grade hPSC.

Arthropods associated with fungal galls: do large galls support more abundant and diverse inhabitants?

NASA Astrophysics Data System (ADS)

Funamoto, Daichi; Sugiura, Shinji

2017-02-01

Fungus-induced galls can attract spore-feeding arthropods as well as gall-feeding ones, resulting in diverse communities. Do large fungal galls support more abundant and diverse arthropod communities than small fungal galls? To address this question, we investigated the structure of the arthropod community associated with bud galls induced by the fungus Melanopsichium onumae on the tree species Cinnamomum yabunikkei (Lauraceae) in central Japan. Thirteen species of arthropods were associated with M. onumae galls. Dominant arthropod species were represented by the larvae of a salpingid beetle (a spore feeder), a nitidulid beetle (a spore feeder), a cosmopterigid moth (a spore feeder), an unidentified moth (a gall tissue feeder), and a drosophilid species (a gall tissue feeder). Arthropod abundance and species richness were positively correlated with gall diameter. The majority of the most abundant species were more frequently found in large galls than in small ones, indicating that large fungal galls, which have more food and/or space for arthropods, could support a more abundant and diverse arthropod community.

A new angle on microscopic suspension feeders near boundaries.

PubMed

Pepper, Rachel E; Roper, Marcus; Ryu, Sangjin; Matsumoto, Nobuyoshi; Nagai, Moeto; Stone, Howard A

2013-10-15

Microscopic sessile suspension feeders are a critical component in aquatic ecosystems, acting as an intermediate trophic stage between bacteria and higher eukaryotic taxa. Because they live attached to boundaries, it has long been thought that recirculation of the feeding currents produced by sessile suspension feeders inhibits their ability to access fresh fluid. However, previous models for the feeding flows of these organisms assume that they feed by pushing fluid perpendicular to surfaces they live upon, whereas we observe that sessile suspension feeders often feed at an angle to these boundaries. Using experiments and calculations, we show that living suspension feeders (Vorticella) likely actively regulate the angle that they feed relative to a substratum. We then use theory and simulations to show that angled feeding increases nutrient and particle uptake by reducing the reprocessing of depleted water. This work resolves an open question of how a key class of suspension-feeding organisms escapes physical limitations associated with their sessile lifestyle. Copyright © 2013 Biophysical Society. Published by Elsevier Inc. All rights reserved.

Nutrient compensatory foraging in a free-living social insect

NASA Astrophysics Data System (ADS)

Christensen, Keri L.; Gallacher, Anthony P.; Martin, Lizzie; Tong, Desmond; Elgar, Mark A.

2010-10-01

The geometric framework model predicts that animal foraging decisions are influenced by their dietary history, with animals targeting a combination of essential nutrients through compensatory foraging. We provide experimental confirmation of nutrient-specific compensatory foraging in a natural, free-living population of social insects by supplementing their diet with sources of protein- or carbohydrate-rich food. Colonies of the ant Iridomyrmex suchieri were provided with feeders containing food rich in either carbohydrate or protein for 6 days, and were then provided with a feeder containing the same or different diet. The patterns of recruitment were consistent with the geometric framework: while feeders with a carbohydrate diet typically attracted more workers than did feeders with protein diet, the difference in recruitment between the two nutrients was smaller if the colonies had had prior access to carbohydrate than protein. Further, fewer ants visited feeders if the colony had had prior access to protein than to carbohydrates, suggesting that the larvae play a role in worker foraging behaviour.

A novel method for interactive multi-objective dose-guided patient positioning

NASA Astrophysics Data System (ADS)

Haehnle, Jonas; Süss, Philipp; Landry, Guillaume; Teichert, Katrin; Hille, Lucas; Hofmaier, Jan; Nowak, Dimitri; Kamp, Florian; Reiner, Michael; Thieke, Christian; Ganswindt, Ute; Belka, Claus; Parodi, Katia; Küfer, Karl-Heinz; Kurz, Christopher

2017-01-01

In intensity-modulated radiation therapy (IMRT), 3D in-room imaging data is typically utilized for accurate patient alignment on the basis of anatomical landmarks. In the presence of non-rigid anatomical changes, it is often not obvious which patient position is most suitable. Thus, dose-guided patient alignment is an interesting approach to use available in-room imaging data for up-to-date dose calculation, aimed at finding the position that yields the optimal dose distribution. This contribution presents the first implementation of dose-guided patient alignment as multi-criteria optimization problem. User-defined clinical objectives are employed for setting up a multi-objective problem. Using pre-calculated dose distributions at a limited number of patient shifts and dose interpolation, a continuous space of Pareto-efficient patient shifts becomes accessible. Pareto sliders facilitate interactive browsing of the possible shifts with real-time dose display to the user. Dose interpolation accuracy is validated and the potential of multi-objective dose-guided positioning demonstrated for three head and neck (H&N) and three prostate cancer patients. Dose-guided positioning is compared to replanning for all cases. A delineated replanning CT served as surrogate for in-room imaging data. Dose interpolation accuracy was high. Using a 2 % dose difference criterion, a median pass-rate of 95.7% for H&N and 99.6% for prostate cases was determined in a comparison to exact dose calculations. For all patients, dose-guided positioning allowed to find a clinically preferable dose distribution compared to bony anatomy based alignment. For all H&N cases, mean dose to the spared parotid glands was below 26~\\text{Gy} (up to 27.5~\\text{Gy} with bony alignment) and clinical target volume (CTV) {{V}95 % } above 99.1% (compared to 95.1%). For all prostate patients, CTV {{V}95 % } was above 98.9% (compared to 88.5%) and {{V}50~\\text{Gy}} to the rectum below 50 % (compared to 56.1%). Replanning yielded improved results for the H&N cases. For the prostate cases, differences to dose-guided positioning were minor.

High voltage systems (tube-type microwave)/low voltage system (solid-state microwave) power distribution

NASA Technical Reports Server (NTRS)

Nussberger, A. A.; Woodcock, G. R.

1980-01-01

SPS satellite power distribution systems are described. The reference Satellite Power System (SPS) concept utilizes high-voltage klystrons to convert the onboard satellite power from dc to RF for transmission to the ground receiving station. The solar array generates this required high voltage and the power is delivered to the klystrons through a power distribution subsystem. An array switching of solar cell submodules is used to maintain bus voltage regulation. Individual klystron dc voltage conversion is performed by centralized converters. The on-board data processing system performs the necessary switching of submodules to maintain voltage regulation. Electrical power output from the solar panels is fed via switch gears into feeder buses and then into main distribution buses to the antenna. Power also is distributed to batteries so that critical functions can be provided through solar eclipses.

On Multi-Objective Based Constitutive Modelling Methodology and Numerical Validation in Small-Hole Drilling of Al6063/SiCp Composites

PubMed Central

Xiang, Junfeng; Xie, Lijing; Gao, Feinong; Zhang, Yu; Yi, Jie; Wang, Tao; Pang, Siqin; Wang, Xibin

2018-01-01

Discrepancies in capturing material behavior of some materials, such as Particulate Reinforced Metal Matrix Composites, by using conventional ad hoc strategy make the applicability of Johnson-Cook constitutive model challenged. Despites applicable efforts, its extended formalism with more fitting parameters would increase the difficulty in identifying constitutive parameters. A weighted multi-objective strategy for identifying any constitutive formalism is developed to predict mechanical behavior in static and dynamic loading conditions equally well. These varying weighting is based on the Gaussian-distributed noise evaluation of experimentally obtained stress-strain data in quasi-static or dynamic mode. This universal method can be used to determine fast and directly whether the constitutive formalism is suitable to describe the material constitutive behavior by measuring goodness-of-fit. A quantitative comparison of different fitting strategies on identifying Al6063/SiCp’s material parameters is made in terms of performance evaluation including noise elimination, correlation, and reliability. Eventually, a three-dimensional (3D) FE model in small-hole drilling of Al6063/SiCp composites, using multi-objective identified constitutive formalism, is developed. Comparison with the experimental observations in thrust force, torque, and chip morphology provides valid evidence on the applicability of the developed multi-objective identification strategy in identifying constitutive parameters. PMID:29324688

Development of a Xeno-Free Feeder-Layer System from Human Umbilical Cord Mesenchymal Stem Cells for Prolonged Expansion of Human Induced Pluripotent Stem Cells in Culture

PubMed Central

Zou, Qing; Wu, Mingjun; Zhong, Liwu; Fan, Zhaoxin; Zhang, Bo; Chen, Qiang; Ma, Feng

2016-01-01

Various feeder layers have been extensively applied to support the prolonged growth of human pluripotent stem cells (hPSCs) for in vitro cultures. Among them, mouse embryonic fibroblast (MEF) and mouse fibroblast cell line (SNL) are most commonly used feeder cells for hPSCs culture. However, these feeder layers from animal usually cause immunogenic contaminations, which compromises the potential of hPSCs in clinical applications. In the present study, we tested human umbilical cord mesenchymal stem cells (hUC-MSCs) as a potent xeno-free feeder system for maintaining human induced pluripotent stem cells (hiPSCs). The hUC-MSCs showed characteristics of MSCs in xeno-free culture condition. On the mitomycin-treated hUC-MSCs feeder, hiPSCs maintained the features of undifferentiated human embryonic stem cells (hESCs), such as low efficiency of spontaneous differentiation, stable expression of stemness markers, maintenance of normal karyotypes, in vitro pluripotency and in vivo ability to form teratomas, even after a prolonged culture of more than 30 passages. Our study indicates that the xeno-free culture system may be a good candidate for growth and expansion of hiPSCs as the stepping stone for stem cell research to further develop better and safer stem cells. PMID:26882313

Development of a Xeno-Free Feeder-Layer System from Human Umbilical Cord Mesenchymal Stem Cells for Prolonged Expansion of Human Induced Pluripotent Stem Cells in Culture.

PubMed

Zou, Qing; Wu, Mingjun; Zhong, Liwu; Fan, Zhaoxin; Zhang, Bo; Chen, Qiang; Ma, Feng

2016-01-01

Various feeder layers have been extensively applied to support the prolonged growth of human pluripotent stem cells (hPSCs) for in vitro cultures. Among them, mouse embryonic fibroblast (MEF) and mouse fibroblast cell line (SNL) are most commonly used feeder cells for hPSCs culture. However, these feeder layers from animal usually cause immunogenic contaminations, which compromises the potential of hPSCs in clinical applications. In the present study, we tested human umbilical cord mesenchymal stem cells (hUC-MSCs) as a potent xeno-free feeder system for maintaining human induced pluripotent stem cells (hiPSCs). The hUC-MSCs showed characteristics of MSCs in xeno-free culture condition. On the mitomycin-treated hUC-MSCs feeder, hiPSCs maintained the features of undifferentiated human embryonic stem cells (hESCs), such as low efficiency of spontaneous differentiation, stable expression of stemness markers, maintenance of normal karyotypes, in vitro pluripotency and in vivo ability to form teratomas, even after a prolonged culture of more than 30 passages. Our study indicates that the xeno-free culture system may be a good candidate for growth and expansion of hiPSCs as the stepping stone for stem cell research to further develop better and safer stem cells.

Effects of Weaning and Spatial Enrichment on Behavior of Turkish Saanen Goat Kids.

PubMed

Tölü, Cemil; Göktürk, Semra; Sava, Türker

2016-06-01

As is in all economic activities, the highest yield per unit area is the main goal in animal production, while addressing the temperamental needs of animals often is ignored. Animal welfare is not only an ethical fact; it also has an economic value. Spatial environmental enrichment contributes positively to animal welfare by addressing their behavioral and mental requirements. The present study was conducted to determine the effects of weaning and spatial environmental arrangements on behaviors of goat-kids. Experimental groups were arranged in structured and unstructured spatial environments. Roughage feeder, semi-automatic concentrate feeder, bunk, bridge, and wood block were placed in the structured environment. No equipment was placed in the unstructured environment and paddock sides were enclosed with an iron sheet to prevent bipedal stance and to provide environmental isolation. In the study 10 male and 10 female Turkish Saanen goat kids were used in each group. Spatial environmental arrangements did not have significant impacts on the growth performance of kids (p>0.05). All objects in the structured group were accepted by the kids. Average use ratios of roughage feeder, semi-automatic concentrate feeder, bunk, bridge and wood block were observed as 19.3%, 14.0%, 12.6%, 3.8%, and 0.7%, respectively. There were significant differences between before- and after-weaning in use of all objects except for underneath bridge (p≤0.05). Concentrate feed consumption, locomotion, and resting behaviors in kids showed significant differences by structural group and growth period. Roughage consumption was similar between groups, while it differed by growth period (p≤0.05). Interaction frequency was significantly higher in structured group (p = 0.0023). Playing behavior significantly differentiated based on the growth period rather than on groups (p≤0.05). Playing behavior significantly decreased after weaning. Abnormal oral activity was significantly higher in the structured group before weaning (p≤0.05). Despite there being no installations facilitating climbing and bipedal stance, the kids of the unstructured group were able to exhibit 1/3 as much bipedal stance behavior as the kids of the structured group through leaning over slippery paddock wall or over their groupmates. Bipedal stance behavior of unstructured group was similar before and after weaning, while bipedal stance behavior before weaning was about 2 times that of after weaning in structured group. It was concluded that unstructured environmental arrangement limited the behavior repertoire of the goat kids.

Effects of Weaning and Spatial Enrichment on Behavior of Turkish Saanen Goat Kids

PubMed Central

Tölü, Cemil; Göktürk, Semra; Sava, Türker

2016-01-01

As is in all economic activities, the highest yield per unit area is the main goal in animal production, while addressing the temperamental needs of animals often is ignored. Animal welfare is not only an ethical fact; it also has an economic value. Spatial environmental enrichment contributes positively to animal welfare by addressing their behavioral and mental requirements. The present study was conducted to determine the effects of weaning and spatial environmental arrangements on behaviors of goat-kids. Experimental groups were arranged in structured and unstructured spatial environments. Roughage feeder, semi-automatic concentrate feeder, bunk, bridge, and wood block were placed in the structured environment. No equipment was placed in the unstructured environment and paddock sides were enclosed with an iron sheet to prevent bipedal stance and to provide environmental isolation. In the study 10 male and 10 female Turkish Saanen goat kids were used in each group. Spatial environmental arrangements did not have significant impacts on the growth performance of kids (p>0.05). All objects in the structured group were accepted by the kids. Average use ratios of roughage feeder, semi-automatic concentrate feeder, bunk, bridge and wood block were observed as 19.3%, 14.0%, 12.6%, 3.8%, and 0.7%, respectively. There were significant differences between before- and after-weaning in use of all objects except for underneath bridge (p≤0.05). Concentrate feed consumption, locomotion, and resting behaviors in kids showed significant differences by structural group and growth period. Roughage consumption was similar between groups, while it differed by growth period (p≤0.05). Interaction frequency was significantly higher in structured group (p = 0.0023). Playing behavior significantly differentiated based on the growth period rather than on groups (p≤0.05). Playing behavior significantly decreased after weaning. Abnormal oral activity was significantly higher in the structured group before weaning (p≤0.05). Despite there being no installations facilitating climbing and bipedal stance, the kids of the unstructured group were able to exhibit 1/3 as much bipedal stance behavior as the kids of the structured group through leaning over slippery paddock wall or over their groupmates. Bipedal stance behavior of unstructured group was similar before and after weaning, while bipedal stance behavior before weaning was about 2 times that of after weaning in structured group. It was concluded that unstructured environmental arrangement limited the behavior repertoire of the goat kids. PMID:26954169

Multi-band morpho-Spectral Component Analysis Deblending Tool (MuSCADeT): Deblending colourful objects

NASA Astrophysics Data System (ADS)

Joseph, R.; Courbin, F.; Starck, J.-L.

2016-05-01

We introduce a new algorithm for colour separation and deblending of multi-band astronomical images called MuSCADeT which is based on Morpho-spectral Component Analysis of multi-band images. The MuSCADeT algorithm takes advantage of the sparsity of astronomical objects in morphological dictionaries such as wavelets and their differences in spectral energy distribution (SED) across multi-band observations. This allows us to devise a model independent and automated approach to separate objects with different colours. We show with simulations that we are able to separate highly blended objects and that our algorithm is robust against SED variations of objects across the field of view. To confront our algorithm with real data, we use HST images of the strong lensing galaxy cluster MACS J1149+2223 and we show that MuSCADeT performs better than traditional profile-fitting techniques in deblending the foreground lensing galaxies from background lensed galaxies. Although the main driver for our work is the deblending of strong gravitational lenses, our method is fit to be used for any purpose related to deblending of objects in astronomical images. An example of such an application is the separation of the red and blue stellar populations of a spiral galaxy in the galaxy cluster Abell 2744. We provide a python package along with all simulations and routines used in this paper to contribute to reproducible research efforts. Codes can be found at http://lastro.epfl.ch/page-126973.html

Multi-object model-based multi-atlas segmentation for rodent brains using dense discrete correspondences

NASA Astrophysics Data System (ADS)

Lee, Joohwi; Kim, Sun Hyung; Styner, Martin

2016-03-01

The delineation of rodent brain structures is challenging due to low-contrast multiple cortical and subcortical organs that are closely interfacing to each other. Atlas-based segmentation has been widely employed due to its ability to delineate multiple organs at the same time via image registration. The use of multiple atlases and subsequent label fusion techniques has further improved the robustness and accuracy of atlas-based segmentation. However, the accuracy of atlas-based segmentation is still prone to registration errors; for example, the segmentation of in vivo MR images can be less accurate and robust against image artifacts than the segmentation of post mortem images. In order to improve the accuracy and robustness of atlas-based segmentation, we propose a multi-object, model-based, multi-atlas segmentation method. We first establish spatial correspondences across atlases using a set of dense pseudo-landmark particles. We build a multi-object point distribution model using those particles in order to capture inter- and intra- subject variation among brain structures. The segmentation is obtained by fitting the model into a subject image, followed by label fusion process. Our result shows that the proposed method resulted in greater accuracy than comparable segmentation methods, including a widely used ANTs registration tool.

A Scalable and Robust Multi-Agent Approach to Distributed Optimization

NASA Technical Reports Server (NTRS)

Tumer, Kagan

2005-01-01

Modularizing a large optimization problem so that the solutions to the subproblems provide a good overall solution is a challenging problem. In this paper we present a multi-agent approach to this problem based on aligning the agent objectives with the system objectives, obviating the need to impose external mechanisms to achieve collaboration among the agents. This approach naturally addresses scaling and robustness issues by ensuring that the agents do not rely on the reliable operation of other agents We test this approach in the difficult distributed optimization problem of imperfect device subset selection [Challet and Johnson, 2002]. In this problem, there are n devices, each of which has a "distortion", and the task is to find the subset of those n devices that minimizes the average distortion. Our results show that in large systems (1000 agents) the proposed approach provides improvements of over an order of magnitude over both traditional optimization methods and traditional multi-agent methods. Furthermore, the results show that even in extreme cases of agent failures (i.e., half the agents fail midway through the simulation) the system remains coordinated and still outperforms a failure-free and centralized optimization algorithm.

Power Distribution System Planning with GIS Consideration

NASA Astrophysics Data System (ADS)

Wattanasophon, Sirichai; Eua-Arporn, Bundhit

This paper proposes a method for solving radial distribution system planning problems taking into account geographical information. The proposed method can automatically determine appropriate location and size of a substation, routing of feeders, and sizes of conductors while satisfying all constraints, i.e. technical constraints (voltage drop and thermal limit) and geographical constraints (obstacle, existing infrastructure, and high-cost passages). Sequential quadratic programming (SQP) and minimum path algorithm (MPA) are applied to solve the planning problem based on net price value (NPV) consideration. In addition this method integrates planner's experience and optimization process to achieve an appropriate practical solution. The proposed method has been tested with an actual distribution system, from which the results indicate that it can provide satisfactory plans.

A framework for multi-stakeholder decision-making and conflict resolution

EPA Science Inventory

We propose a decision-making framework to compute compromise solutions that balance conflicting priorities of multiple stakeholders on multiple objectives. In our setting, we shape the stakeholder dis-satisfaction distribution by solving a conditional-value-at-risk (CVaR) minimiz...

Effects of diet form and feeder adjustment on growth performance of nursery and finishing pigs.

PubMed

Nemechek, J E; Tokach, M D; Dritz, S S; Fruge, E D; Hansen, E L; Goodband, R D; DeRouchey, J M; Woodworth, J C

2015-08-01

Three experiments were conducted to determine the effects of feeder adjustment and diet form on growth performance of nursery (Exp. 1 and 2) and finishing (Exp. 3) pigs. Treatments were arranged as a 2 × 3 factorial with the main effects of feeder adjustment and diet form. The 2 feeder adjustments were a narrow and wide feeder adjustment (minimum gap opening of 1.27 and 2.54 cm, respectively). The 3 diet forms were meal, poor-quality pellets (70% pellets and 30% fines for Exp. 1 and 2 and 50% pellets and 50% fines for Exp. 3), and screened pellets with minimal fines (3 to 10%). In Exp. 1, 210 pigs (initially 11.9 kg BW) were used in a 21-d trial with 7 pigs per pen and 5 pens per treatment. No feeder adjustment × diet form interactions were observed. There were no differences in ADG, ADFI, or G:F due to feeder adjustment. Pigs fed the meal diet had increased ( < 0.05) ADG and ADFI compared with pigs fed the poor-quality or screened pellets. Pigs fed meal or poor-quality pellets had decreased ( < 0.05) G:F compared with pigs fed screened pellets. In Exp. 2, 1,005 nursery pigs (initially 14.1 kg BW) were used in a 28-d trial with 26 to 28 pigs per pen and 6 pens per treatment. Pigs fed from the narrow feeder adjustment had decreased ( < 0.05) ADG and ADFI compared with pigs fed from the wide adjustment with no differences in G:F. Pigs fed the meal diet had decreased ( < 0.05) ADG compared with pigs fed poor-quality or screened pellets. Pigs fed meal or poor-quality pellets had decreased ( < 0.05) G:F compared with pigs fed screened pellets. In Exp. 3, 246 pigs (initially 56.8 kg BW) were used in a 69-d trial with 5 pens per treatment and 6 or 7 pigs per pen. Overall, ADFI decreased ( < 0.05) and G:F increased ( < 0.05) for pigs fed from the narrow adjusted feeders compared with the wide adjustment with no differences in ADG. Overall, pigs fed meal diets tended to have decreased ( < 0.10) ADG and had decreased ( < 0.05) G:F compared with pigs fed screened pellets; ADG and G:F in those fed poor-quality pellets were intermediate. Feeding meal or poor-quality pellets increased ( < 0.05) ADFI compared with pigs fed screened pellets. In conclusion, feeding nursery pigs from a wide feeder gap may increase ADG and ADFI with no negative effects on G:F. For finishing pigs, reducing feeder gap reduced feed disappearance and improved G:F. In all experiments, the greatest G:F improvements from pelleting were observed when the percentage of fines was minimized.

Exposure cell number during feeder cell growth-arrest by Mitomycin C is a critical pharmacological aspect in stem cell culture system.

PubMed

Chugh, Rishi Man; Chaturvedi, Madhusudan; Yerneni, Lakshmana Kumar

2016-01-01

Growth-arrested feeder cells following Mitomycin C treatment are instrumental in stem cell culture allowing development of regenerative strategies and alternatives to animal testing in drug discovery. The concentration of Mitomycin C and feeder cell type was described to affect feeder performance but the criticality of feeder cell exposure density was not addressed. We hypothesize that the exposure cell density influences the effectiveness of Mitomycin C in an arithmetic manner. Three different exposure cell densities of Swiss 3T3 fibroblasts were treated with a range of Mitomycin C concentrations for 2h. The cells were replaced and the viable cells counted on 3, 6, 9, 12 and 20days. The cell extinctions were compared with doses per cell which were derived by dividing the product of concentration and volume of Mitomycin C solution with exposure cell number. The periodic post-treatment feeder cell extinctions were not just dependent on Mitomycin C concentration but also on dose per cell. Analysis of linearity between viable cell number and Mitomycin C dose per cell derived from the concentrations of 3 to 10μg/ml revealed four distinct categories of growth-arrest. Confluent cultures exposed to low concentration showed growth-arrest failure. The in vitro cell density titration can facilitate prediction of a compound's operational in vivo dosing. For containing the growth arrest failure, an arithmetic volume derivation strategy is proposed by fixing the exposure density to a safe limit. The feeder extinction characteristics are critical for streamlining the stem cell based pharmacological and toxicological assays. Copyright © 2016 Elsevier Inc. All rights reserved.

Can rats solve a simple version of the traveling salesman problem?

PubMed

Bures, J; Buresová, O; Nerad, L

1992-12-31

Whereas correct tours through the radial arm maze are almost equally long, free choice mazes with multiple goals scattered in an open field allow the animal to select the shortest one from a multitude of correct tours. Thirteen rats were trained (at 10 trials per day) to visit an array of cylindrical feeders in an open field (40 x 100 cm) with reward available only when visiting the last feeder of the set. In Expt. 1 with eight feeders arranged in five different configurations the rats made after 10 days of training 1 error in the first 8 choices and incidence of errorless trials was about 20%. In Expt. 2. the use of six feeders in a rectangular (A) or double triangle (B) configuration increased the incidence of errorless trials to 60%. Expt. 3 showed that performance in the 6-feeder maze was significantly impaired by 6 mg/kg ketamine or 0.25 mg/kg scopolamine but not by lower dosages of these drugs. Tours generated on errorless trials (each feeder visited only once) during 10 days of Expt. 2 were analyzed. Six places can be visited in 6! = 720 different closed tours the lengths of which (in arbitrary units) range from 6.00 to 10.12 for A and from 6.83 to 10.47 for B. Whereas random generation of correct routes yielded only 5% of the shortest tours, they were clearly preferred by rats (41% in A and 45% in B). The apparent proficiency of rats in this optimization problem is probably not due to cognitive comparison of the possible correct routes but rather to following a simple rule 'Always go to the nearest not yet visited feeder'.

47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 47 Telecommunication 2 2014-10-01 2014-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...

47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 47 Telecommunication 2 2013-10-01 2013-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...

47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 47 Telecommunication 2 2012-10-01 2012-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...

47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...

47 CFR 25.250 - Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 47 Telecommunication 2 2011-10-01 2011-10-01 false Sharing between NGSO MSS Feeder links Earth....250 Sharing between NGSO MSS Feeder links Earth Stations in the 19.3-19.7 GHz and 29.1-29.5 GHz Bands. (a) NGSO MSS applicants shall be licensed to operate in the 29.1-29.5 GHz band for Earth-to-space...

Offshore Windfarm Impact on Pelagic Primary Production in the Southern North Sea

NASA Astrophysics Data System (ADS)

Slavik, Kaela; Zhang, Wenyan; Lemmen, Carsten; Wirtz, Kai

2016-04-01

As society struggles to find solutions to mitigate global warming, the demand for renewable energy technology has increased. Especially investment in offshore wind energy has proliferated in the European Union, with projections over the next 15 years estimating an over 40 fold increase in total offshore wind electricity. Though built with the goal of reducing the environmental impacts associated with traditional energy production, the long-term ecological impacts of offshore windfarm structures is not yet well understood. The consequences are of particular importance in the southern North Sea, where the expansion of offshore windfarms is focused. Our study investigates how the gradual accumulation of epifaunal biomass on submerged substrate at offshore windfarms impacts ecosystem services in the southern North Sea. Biofouling is governed predominately by the filter feeder Mytilus edulis, which, as an ecological engineer, will further alter the surrounding benthic and pelagic environment. We reconstruct the distribution of benthic filter feeders in the SNS and generate scenarios of increased potential distribution based on available information of Mytilus edulis settlement at turbines and of turbine locations. These maps are coupled through the MOSSCO (Modular Coupling System for Shelves and Coasts) to state-of-the-art and high resolution hydrodynamic and ecosystem models. We find a substantial change in pelagic primary production as a result of additional Mytilus edulis growth at offshore windfarms.

Conceptual Design and Analysis of Cold Mass Support of the CS3U Feeder for the ITER

NASA Astrophysics Data System (ADS)

Zhu, Yinfeng; Song, Yuntao; Zhang, Yuanbin; Wang, Zhongwei

2013-06-01

In the International Thermonuclear Experimental Reactor (ITER) project, the feeders are one of the most important and critical systems. To convey the power supply and the coolant for the central solenoid (CS) magnet, 6 sets of CS feeders are employed, which consist mainly of an in-cryostat feeder (ICF), a cryostat feed-through (CFT), an S-bend box (SBB), and a coil terminal box (CTB). To compensate the displacements of the internal components of the CS feeders during operation, sliding cold mass supports consisting of a sled plate, a cylindrical support, a thermal shield, and an external ring are developed. To check the strength of the developed cold mass supports of the CS3U feeder, electromagnetic analysis of the two superconducting busbars is performed by using the CATIA V5 and ANSYS codes based on parametric technology. Furthermore, the thermal-structural coupling analysis is performed based on the obtained results, except for the stress concentration, and the max. stress intensity is lower than the allowable stress of the selected material. It is found that the conceptual design of the cold mass support can satisfy the required functions under the worst case of normal working conditions. All these performed activities will provide a firm technical basis for the engineering design and development of cold mass supports.

30 CFR 75.1001 - Overcurrent protection.

Code of Federal Regulations, 2011 CFR

2011-07-01

... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1001 Overcurrent protection. [Statutory Provisions] Trolley wires and trolley feeder wires shall be provided with...

30 CFR 75.1001 - Overcurrent protection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1001 Overcurrent protection. [Statutory Provisions] Trolley wires and trolley feeder wires shall be provided with...

Erythro-9-(2-hydroxy-3-nonyl)adenine (EHNA) blocks differentiation and maintains the expression of pluripotency markers in human embryonic stem cells.

PubMed

Burton, Peter; Adams, David R; Abraham, Achamma; Allcock, Robert W; Jiang, Zhong; McCahill, Angela; Gilmour, Jane; McAbney, John; Kaupisch, Alexandra; Kane, Nicole M; Baillie, George S; Baker, Andrew H; Milligan, Graeme; Houslay, Miles D; Mountford, Joanne C

2010-12-15

hESCs (human embryonic stem cells) have enormous potential for use in pharmaceutical development and therapeutics; however, to realize this potential, there is a requirement for simple and reproducible cell culture methods that provide adequate numbers of cells of suitable quality. We have discovered a novel way of blocking the spontaneous differentiation of hESCs in the absence of exogenous cytokines by supplementing feeder-free conditions with EHNA [erythro-9-(2-hydroxy-3-nonyl)adenine], an established inhibitor of ADA (adenosine deaminase) and cyclic nucleotide PDE2 (phosphodiesterase 2). hESCs maintained in feeder-free conditions with EHNA for more than ten passages showed no reduction in hESC-associated markers including NANOG, POU5F1 (POU domain class 5 transcription factor 1, also known as Oct-4) and SSEA4 (stage-specific embryonic antigen 4) compared with cells maintained in feeder-free conditions containing bFGF (basic fibroblast growth factor). Spontaneous differentiation was reversibly suppressed by the addition of EHNA, but, upon removing EHNA, hESC populations underwent efficient spontaneous, multi-lineage and directed differentiation. EHNA also acts as a strong blocker of directed neuronal differentiation. Chemically distinct inhibitors of ADA and PDE2 lacked the capacity of EHNA to suppress hESC differentiation, suggesting that the effect is not driven by inhibition of either ADA or PDE2. Preliminary structure-activity relationship analysis found the differentiation-blocking properties of EHNA to reside in a pharmacophore comprising a close adenine mimetic with an extended hydrophobic substituent in the 8- or 9-position. We conclude that EHNA and simple 9-alkyladenines can block directed neuronal and spontaneous differentiation in the absence of exogenous cytokine addition, and may provide a useful replacement for bFGF in large-scale or cGMP-compliant processes.

30 CFR 75.1000 - Cutout switches.

Code of Federal Regulations, 2011 CFR

2011-07-01

... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1000 Cutout switches. [Statutory Provisions] Trolley wires and trolley feeder wires, shall be provided with cutout...

30 CFR 75.1000 - Cutout switches.

Code of Federal Regulations, 2010 CFR

2010-07-01

... MANDATORY SAFETY STANDARDS-UNDERGROUND COAL MINES Trolley Wires and Trolley Feeder Wires § 75.1000 Cutout switches. [Statutory Provisions] Trolley wires and trolley feeder wires, shall be provided with cutout...

Loss Reduction on Adoption of High Voltage LT Less Distribution

NASA Astrophysics Data System (ADS)

Tiwari, Deepika; Adhikari, Nikhileshwar Prasad; Gupta, Amit; Bajpai, Santosh Kumar

2016-06-01

In India there is a need to improve the quality of the electricity distribution process which has increased varying from year to year. In distribution networks, the limiting factor to load carrying capacity is generally the voltage reduction. High voltage distribution system (HVDS) is one of the steps to reduce line losses in electrical distribution network. It helps to reduce the length of low tension (LT) lines and makes the power available close to the users. The high voltage power distribution system reduces the probability of power theft by hooking HVDS suggests an increase in installation of small capacity single-phase transformers in the network which again save considerable energy. This paper is compared to existing conventional low tension distribution network with HVDS. The paper gives a clear picture of reduction in distribution losses with adoption of HVDS system. Losses Reduction of 11 kV Feeder in Nuniya (India) with adoption of HVDS have been worked out/ quantified and benefits thereby in generating capacity have discussed.

Performance Enhancement of Radial Distributed System with Distributed Generators by Reconfiguration Using Binary Firefly Algorithm

NASA Astrophysics Data System (ADS)

Rajalakshmi, N.; Padma Subramanian, D.; Thamizhavel, K.

2015-03-01

The extent of real power loss and voltage deviation associated with overloaded feeders in radial distribution system can be reduced by reconfiguration. Reconfiguration is normally achieved by changing the open/closed state of tie/sectionalizing switches. Finding optimal switch combination is a complicated problem as there are many switching combinations possible in a distribution system. Hence optimization techniques are finding greater importance in reducing the complexity of reconfiguration problem. This paper presents the application of firefly algorithm (FA) for optimal reconfiguration of radial distribution system with distributed generators (DG). The algorithm is tested on IEEE 33 bus system installed with DGs and the results are compared with binary genetic algorithm. It is found that binary FA is more effective than binary genetic algorithm in achieving real power loss reduction and improving voltage profile and hence enhancing the performance of radial distribution system. Results are found to be optimum when DGs are added to the test system, which proved the impact of DGs on distribution system.

Numerical Propulsion System Simulation Architecture

NASA Technical Reports Server (NTRS)

Naiman, Cynthia G.

2004-01-01

The Numerical Propulsion System Simulation (NPSS) is a framework for performing analysis of complex systems. Because the NPSS was developed using the object-oriented paradigm, the resulting architecture is an extensible and flexible framework that is currently being used by a diverse set of participants in government, academia, and the aerospace industry. NPSS is being used by over 15 different institutions to support rockets, hypersonics, power and propulsion, fuel cells, ground based power, and aerospace. Full system-level simulations as well as subsystems may be modeled using NPSS. The NPSS architecture enables the coupling of analyses at various levels of detail, which is called numerical zooming. The middleware used to enable zooming and distributed simulations is the Common Object Request Broker Architecture (CORBA). The NPSS Developer's Kit offers tools for the developer to generate CORBA-based components and wrap codes. The Developer's Kit enables distributed multi-fidelity and multi-discipline simulations, preserves proprietary and legacy codes, and facilitates addition of customized codes. The platforms supported are PC, Linux, HP, Sun, and SGI.

Characterizing the size distribution of particles in urban stormwater by use of fixed-point sample-collection methods

USGS Publications Warehouse

Selbig, William R.; Bannerman, Roger T.

2011-01-01

The U.S Geological Survey, in cooperation with the Wisconsin Department of Natural Resources (WDNR) and in collaboration with the Root River Municipal Stormwater Permit Group monitored eight urban source areas representing six types of source areas in or near Madison, Wis. in an effort to improve characterization of particle-size distributions in urban stormwater by use of fixed-point sample collection methods. The types of source areas were parking lot, feeder street, collector street, arterial street, rooftop, and mixed use. This information can then be used by environmental managers and engineers when selecting the most appropriate control devices for the removal of solids from urban stormwater. Mixed-use and parking-lot study areas had the lowest median particle sizes (42 and 54 (u or mu)m, respectively), followed by the collector street study area (70 (u or mu)m). Both arterial street and institutional roof study areas had similar median particle sizes of approximately 95 (u or mu)m. Finally, the feeder street study area showed the largest median particle size of nearly 200 (u or mu)m. Median particle sizes measured as part of this study were somewhat comparable to those reported in previous studies from similar source areas. The majority of particle mass in four out of six source areas was silt and clay particles that are less than 32 (u or mu)m in size. Distributions of particles ranging from 500 (u or mu)m were highly variable both within and between source areas. Results of this study suggest substantial variability in data can inhibit the development of a single particle-size distribution that is representative of stormwater runoff generated from a single source area or land use. Continued development of improved sample collection methods, such as the depth-integrated sample arm, may reduce variability in particle-size distributions by mitigating the effect of sediment bias inherent with a fixed-point sampler.

Phase I of The National Beef Quality Audit-2011: quantifying willingness-to-pay, best-worst scaling, and current status of quality characteristics in different beef industry marketing sectors.

PubMed

Igo, J L; VanOverbeke, D L; Woerner, D R; Tatum, J D; Pendell, D L; Vedral, L L; Mafi, G G; Moore, M C; McKeith, R O; Gray, G D; Griffin, D B; Hale, D S; Savell, J W; Belk, K E

2013-04-01

The National Beef Quality Audit (NBQA)-2011 benchmarked the current status of and assessed progress being made toward quality and consistency of U.S. cattle, carcasses, and beef products after the completion of the first NBQA in 1991. Unlike previous NBQA, objectives of the 2011 Phase I study were to determine how each beef market sector defined 7 quality categories, estimate willingness-to-pay (WTP) for the same quality categories by market sector, and establish a best-worst (B/W) scaling for the quality categories. Structured face-to-face interviews were conducted and responses were recorded using dynamic routing software over an 11-mo period (February to December 2011) with decision makers in each of the following beef market sectors: Feeders (n = 59), Packers (n = 26), Food Service, Distribution, and Further Processors (n = 48), Retailers (n = 30), and Government and Allied Industries (n = 47). All respondents participated in a structured interview consisting of WTP and B/W questions that were tied to 7 quality categories and then were asked to "define" each of the 7 categories in terms of what the category meant to them, resulting in completely unbiased results. The 7 quality categories were a) how and where the cattle were raised, b) lean, fat, and bone, c) weight and size, d) cattle genetics, e) visual characteristics, f) food safety, and g) eating satisfaction. Overall, "food safety" and "eating satisfaction" were the categories of greatest and second most importance, respectively, to all beef market sectors except for Feeders. Feeders ranked "how and where the cattle were raised" and "weight and size" as the most important and second most important, respectively. Overall, "how and where the cattle were raised" had the greatest odds of being considered a nonnegotiable requirement before the raw material for each sector would be considered for purchase and was statistically more important (P < 0.05) as a requirement for purchase than all other categories except "food safety." When all market sectors were considered, "eating satisfaction" was shown to generate the greatest average WTP percentage premium (11.1%), but that WTP premium value only differed statistically (P < 0.05) from "weight and size" (8.8%). Most notably, when a sector said that "food safety" was a nonnegotiable requirement, no sector was willing to purchase the product at a discounted price if the "food safety" of the product could not be assured.

PGA/MOEAD: a preference-guided evolutionary algorithm for multi-objective decision-making problems with interval-valued fuzzy preferences

NASA Astrophysics Data System (ADS)

Luo, Bin; Lin, Lin; Zhong, ShiSheng

2018-02-01

In this research, we propose a preference-guided optimisation algorithm for multi-criteria decision-making (MCDM) problems with interval-valued fuzzy preferences. The interval-valued fuzzy preferences are decomposed into a series of precise and evenly distributed preference-vectors (reference directions) regarding the objectives to be optimised on the basis of uniform design strategy firstly. Then the preference information is further incorporated into the preference-vectors based on the boundary intersection approach, meanwhile, the MCDM problem with interval-valued fuzzy preferences is reformulated into a series of single-objective optimisation sub-problems (each sub-problem corresponds to a decomposed preference-vector). Finally, a preference-guided optimisation algorithm based on MOEA/D (multi-objective evolutionary algorithm based on decomposition) is proposed to solve the sub-problems in a single run. The proposed algorithm incorporates the preference-vectors within the optimisation process for guiding the search procedure towards a more promising subset of the efficient solutions matching the interval-valued fuzzy preferences. In particular, lots of test instances and an engineering application are employed to validate the performance of the proposed algorithm, and the results demonstrate the effectiveness and feasibility of the algorithm.

Propagation of neutron-reaction uncertainties through multi-physics models of novel LWR's

NASA Astrophysics Data System (ADS)

Hernandez-Solis, Augusto; Sjöstrand, Henrik; Helgesson, Petter

2017-09-01

The novel design of the renewable boiling water reactor (RBWR) allows a breeding ratio greater than unity and thus, it aims at providing for a self-sustained fuel cycle. The neutron reactions that compose the different microscopic cross-sections and angular distributions are uncertain, so when they are employed in the determination of the spatial distribution of the neutron flux in a nuclear reactor, a methodology should be employed to account for these associated uncertainties. In this work, the Total Monte Carlo (TMC) method is used to propagate the different neutron-reactions (as well as angular distributions) covariances that are part of the TENDL-2014 nuclear data (ND) library. The main objective is to propagate them through coupled neutronic and thermal-hydraulic models in order to assess the uncertainty of important safety parameters related to multi-physics, such as peak cladding temperature along the axial direction of an RBWR fuel assembly. The objective of this study is to quantify the impact that ND covariances of important nuclides such as U-235, U-238, Pu-239 and the thermal scattering of hydrogen in H2O have in the deterministic safety analysis of novel nuclear reactors designs.

Flexible power and bandwidth allocation in mobile satellites

NASA Astrophysics Data System (ADS)

Keyes, L. A.

The introduction of L-band mobile communication services by spot beam satellites creates a payload design challenge due to uncertainty in the location and size of the new market to be served. A combination of payload technologies that allow a flexible allocation of power and bandwidth to any portion of the coverage area is described. Power flexibility is achieved by a novel combination of a low-level beam-forming network and a matrix power module which ensures equal sharing of power among individual amplifiers. This eliminates the loss of efficiency and increased mass when an amplifier associated with a beam must be over-designed to meet uncertainties in power distribution between beams. Flexibility in allocation of bandwidth to beams is achieved by intermediate frequency subdivision of the L-band service categories defined by ITU. These spectral subdivisions are assigned to beams by an IF interconnect matrix having beam ports and filter ports as inputs and outputs, respectively. Two such filter switch matrices are required, one for the inbound L-band to feeder link transponder, and one for the outbound feeder link to L-band transponder.

User-assisted visual search and tracking across distributed multi-camera networks

NASA Astrophysics Data System (ADS)

Raja, Yogesh; Gong, Shaogang; Xiang, Tao

2011-11-01

Human CCTV operators face several challenges in their task which can lead to missed events, people or associations, including: (a) data overload in large distributed multi-camera environments; (b) short attention span; (c) limited knowledge of what to look for; and (d) lack of access to non-visual contextual intelligence to aid search. Developing a system to aid human operators and alleviate such burdens requires addressing the problem of automatic re-identification of people across disjoint camera views, a matching task made difficult by factors such as lighting, viewpoint and pose changes and for which absolute scoring approaches are not best suited. Accordingly, we describe a distributed multi-camera tracking (MCT) system to visually aid human operators in associating people and objects effectively over multiple disjoint camera views in a large public space. The system comprises three key novel components: (1) relative measures of ranking rather than absolute scoring to learn the best features for matching; (2) multi-camera behaviour profiling as higher-level knowledge to reduce the search space and increase the chance of finding correct matches; and (3) human-assisted data mining to interactively guide search and in the process recover missing detections and discover previously unknown associations. We provide an extensive evaluation of the greater effectiveness of the system as compared to existing approaches on industry-standard i-LIDS multi-camera data.

Strategic rehabilitation planning of piped water networks using multi-criteria decision analysis.

PubMed

Scholten, Lisa; Scheidegger, Andreas; Reichert, Peter; Maurer, Max; Mauer, Max; Lienert, Judit

2014-02-01

To overcome the difficulties of strategic asset management of water distribution networks, a pipe failure and a rehabilitation model are combined to predict the long-term performance of rehabilitation strategies. Bayesian parameter estimation is performed to calibrate the failure and replacement model based on a prior distribution inferred from three large water utilities in Switzerland. Multi-criteria decision analysis (MCDA) and scenario planning build the framework for evaluating 18 strategic rehabilitation alternatives under future uncertainty. Outcomes for three fundamental objectives (low costs, high reliability, and high intergenerational equity) are assessed. Exploitation of stochastic dominance concepts helps to identify twelve non-dominated alternatives and local sensitivity analysis of stakeholder preferences is used to rank them under four scenarios. Strategies with annual replacement of 1.5-2% of the network perform reasonably well under all scenarios. In contrast, the commonly used reactive replacement is not recommendable unless cost is the only relevant objective. Exemplified for a small Swiss water utility, this approach can readily be adapted to support strategic asset management for any utility size and based on objectives and preferences that matter to the respective decision makers. Copyright © 2013 Elsevier Ltd. All rights reserved.

The DEIMOS 10K Spectroscopic Survey Catalog of the COSMOS Field

NASA Astrophysics Data System (ADS)

Hasinger, G.; Capak, P.; Salvato, M.; Barger, A. J.; Cowie, L. L.; Faisst, A.; Hemmati, S.; Kakazu, Y.; Kartaltepe, J.; Masters, D.; Mobasher, B.; Nayyeri, H.; Sanders, D.; Scoville, N. Z.; Suh, H.; Steinhardt, C.; Yang, Fengwei

2018-05-01

We present a catalog of 10,718 objects in the COSMOS field, observed through multi-slit spectroscopy with the Deep Imaging Multi-Object Spectrograph (DEIMOS) on the Keck II telescope in the wavelength range ∼5500–9800 Å. The catalog contains 6617 objects with high-quality spectra (two or more spectral features), and 1798 objects with a single spectroscopic feature confirmed by the photometric redshift. For 2024 typically faint objects, we could not obtain reliable redshifts. The objects have been selected from a variety of input catalogs based on multi-wavelength observations in the field, and thus have a diverse selection function, which enables the study of the diversity in the galaxy population. The magnitude distribution of our objects is peaked at I AB ∼ 23 and K AB ∼ 21, with a secondary peak at K AB ∼ 24. We sample a broad redshift distribution in the range 0 < z < 6, with one peak at z ∼ 1, and another one around z ∼ 4. We have identified 13 redshift spikes at z > 0.65 with chance probabilities < 4 × 10‑4, some of which are clearly related to protocluster structures of sizes >10 Mpc. An object-to-object comparison with a multitude of other spectroscopic samples in the same field shows that our DEIMOS sample is among the best in terms of fraction of spectroscopic failures and relative redshift accuracy. We have determined the fraction of spectroscopic blends to about 0.8% in our sample. This is likely a lower limit and at any rate well below the most pessimistic expectations. Interestingly, we find evidence for strong lensing of Lyα background emitters within the slits of 12 of our target galaxies, increasing their apparent density by about a factor of 4. The data presented herein were obtained at the W. M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California and the National Aeronautics and Space Administration. The Observatory was made possible by the generous financial support of the W. M. Keck Foundation.

Collaborative Emission Reduction Model Based on Multi-Objective Optimization for Greenhouse Gases and Air Pollutants.

PubMed

Meng, Qing-chun; Rong, Xiao-xia; Zhang, Yi-min; Wan, Xiao-le; Liu, Yuan-yuan; Wang, Yu-zhi

2016-01-01

CO2 emission influences not only global climate change but also international economic and political situations. Thus, reducing the emission of CO2, a major greenhouse gas, has become a major issue in China and around the world as regards preserving the environmental ecology. Energy consumption from coal, oil, and natural gas is primarily responsible for the production of greenhouse gases and air pollutants such as SO2 and NOX, which are the main air pollutants in China. In this study, a mathematical multi-objective optimization method was adopted to analyze the collaborative emission reduction of three kinds of gases on the basis of their common restraints in different ways of energy consumption to develop an economic, clean, and efficient scheme for energy distribution. The first part introduces the background research, the collaborative emission reduction for three kinds of gases, the multi-objective optimization, the main mathematical modeling, and the optimization method. The second part discusses the four mathematical tools utilized in this study, which include the Granger causality test to analyze the causality between air quality and pollutant emission, a function analysis to determine the quantitative relation between energy consumption and pollutant emission, a multi-objective optimization to set up the collaborative optimization model that considers energy consumption, and an optimality condition analysis for the multi-objective optimization model to design the optimal-pole algorithm and obtain an efficient collaborative reduction scheme. In the empirical analysis, the data of pollutant emission and final consumption of energies of Tianjin in 1996-2012 was employed to verify the effectiveness of the model and analyze the efficient solution and the corresponding dominant set. In the last part, several suggestions for collaborative reduction are recommended and the drawn conclusions are stated.

Collaborative Emission Reduction Model Based on Multi-Objective Optimization for Greenhouse Gases and Air Pollutants

PubMed Central

Zhang, Yi-min; Wan, Xiao-le; Liu, Yuan-yuan; Wang, Yu-zhi

2016-01-01

CO2 emission influences not only global climate change but also international economic and political situations. Thus, reducing the emission of CO2, a major greenhouse gas, has become a major issue in China and around the world as regards preserving the environmental ecology. Energy consumption from coal, oil, and natural gas is primarily responsible for the production of greenhouse gases and air pollutants such as SO2 and NOX, which are the main air pollutants in China. In this study, a mathematical multi-objective optimization method was adopted to analyze the collaborative emission reduction of three kinds of gases on the basis of their common restraints in different ways of energy consumption to develop an economic, clean, and efficient scheme for energy distribution. The first part introduces the background research, the collaborative emission reduction for three kinds of gases, the multi-objective optimization, the main mathematical modeling, and the optimization method. The second part discusses the four mathematical tools utilized in this study, which include the Granger causality test to analyze the causality between air quality and pollutant emission, a function analysis to determine the quantitative relation between energy consumption and pollutant emission, a multi-objective optimization to set up the collaborative optimization model that considers energy consumption, and an optimality condition analysis for the multi-objective optimization model to design the optimal-pole algorithm and obtain an efficient collaborative reduction scheme. In the empirical analysis, the data of pollutant emission and final consumption of energies of Tianjin in 1996–2012 was employed to verify the effectiveness of the model and analyze the efficient solution and the corresponding dominant set. In the last part, several suggestions for collaborative reduction are recommended and the drawn conclusions are stated. PMID:27010658

21 CFR 520.1448a - Monensin blocks.

Code of Federal Regulations, 2011 CFR

2011-04-01

...) Limitations. Block to be fed free choice to pasture cattle (slaughter, stocker, feeder, and dairy and beef.... Blocks to be fed free choice to pasture cattle (slaughter, stocker, feeder, and dairy and beef...

11. MOVABLE BED SEDIMENTATION MODELS. AUTOMATIC SEDIMENT FEEDER DESIGNED AND ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

11. MOVABLE BED SEDIMENTATION MODELS. AUTOMATIC SEDIMENT FEEDER DESIGNED AND BUILT BY WES. - Waterways Experiment Station, Hydraulics Laboratory, Halls Ferry Road, 2 miles south of I-20, Vicksburg, Warren County, MS

Factors affecting body weight loss during commercial long haul transport of cattle in North America.

PubMed

González, L A; Schwartzkopf-Genswein, K S; Bryan, M; Silasi, R; Brown, F

2012-10-01

The objective of the present study was to identify and quantify several factors affecting shrink in cattle during commercial long-haul transport (≥400 km; n = 6,152 journeys). Surveys were designed and delivered to transport carriers to collect relevant information regarding the characteristics of animals, time of loading, origin and destination, and loaded weight before and after transport. In contrast to fat cattle, feeder cattle exhibited greater shrink (4.9 vs. 7.9 ± 0.2% of BW, respectively; P < 0.01), and experienced longer total transport durations (12.4 vs. 14.9 ± 0.99, respectively; P < 0.01) due to border crossing protocols which require mandatory animal inspection. Shrink was greater (P < 0.001) for feeder cattle loaded at ranches/farms and feed yards compared with those loaded at auction markets. Cattle loaded during the afternoon and evening shrank more than those loaded during the night and morning (P < 0.05). Shrinkage was less in cattle transported by truck drivers having 6 or more years of experience hauling livestock compared with those with 5 yr or less (P < 0.05). Shrink increased with both midpoint ambient temperature (% of BW/°C; P < 0.001) and time on truck (% of BW/h; P < 0.001). Temperature and time on truck had a multiplicative effect on each other because shrink increased most rapidly in cattle transported for both longer durations and at higher ambient temperatures (P < 0.001). The rate of shrink over time (% of BW/h) was greatest in cull cattle, intermediate in calves and feeder cattle, and slowest in fat cattle (P < 0.05) but such differences disappeared when the effects of place of origin, loading time, and experience of truck drivers were included in the model. Cull cattle, calves and feeder cattle appear to be more affected by transport compared with fat cattle going to slaughter because of greater shrink. Several factors should be considered when developing guidelines to reduce cattle transport stress and shrink including type of cattle, ambient temperature, transport duration, driving quality, and time and origin of loading.

CFD Application to Flow-Accelerated Corrosion in Feeder Bends

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pietralik, John M.; Smith, Bruce A.W.

2006-07-01

Feeder piping in CANDU{sup R} plants experiences a thinning degradation mechanism called Flow-Accelerated Corrosion (FAC). The piping is made of carbon steel and has high water flow speeds. Although the water chemistry is highly alkaline with room-temperature pH in a range of 10.0-10.5, the piping has FAC rates exceeding 0.1 mm/year in some locations, e.g., in bends. One of the most important parameters affecting the FAC rate is the mass transfer coefficient for convective mass transport of ferrous ions. The ions are created at the pipe wall as a result of corrosion, diffuse through the oxide layer, and are transportedmore » from the oxide-layer/water interface to the bulk water by mass transport. Consequently, the local flow characteristics contribute to the highly turbulent convective mass transfer. Plant data and laboratory experiments indicate that the mass transfer step dominates FAC under feeder conditions. In this study, the flow and mass transfer in a feeder bend under operating conditions were simulated using the Fluent{sup TM} computer code. Because the flow speed is very high, with the Reynolds numbers in a range of several millions, and because the geometry is complex, experiments in a 1:1 scale were conducted with the main objective to validate flow simulations. The experiments measured pressure at several key locations and visualized the flow. The flow and mass transfer models were validated using available friction-factor and mass transfer correlations and literature experiments on mass transfer in a bend. The validation showed that the turbulence model that best predicts the experiments is the realizable k-{epsilon} model. Other two-equation turbulence models, as well as one-equation models and Reynolds stress models were tried. The near-wall treatment used the non-equilibrium wall functions. The wall functions were modified for surface roughness when necessary. A comparison of the local mass transfer coefficient with measured FAC rate in plant specimens shows very good agreement. Visualization experiments indicate secondary flows in the bends. No boundary layer separation was observed in experiments or in simulations. (authors)« less

Comparing the engineering program feeders from SiF and convention models

NASA Astrophysics Data System (ADS)

Roongruangsri, Warawaran; Moonpa, Niwat; Vuthijumnonk, Janyawat; Sangsuwan, Kampanart

2018-01-01

This research aims to compare the relationship between two types of engineering program feeder models within the technical education systems of Rajamangala University of Technology Lanna (RMUTL), Chiangmai, Thailand. To illustrate, the paper refers to two typologies of feeder models, which are the convention and the school in factory (SiF) models. The new SiF model is developed through a collaborative educational process between the sectors of industry, government and academia, using work-integrated learning. The research methodology were use to compared features of the the SiF model with conventional models in terms of learning outcome, funding budget for the study, the advantages and disadvantages from the point of view of students, professors, the university, government and industrial partners. The results of this research indicate that the developed SiF feeder model is the most pertinent ones as it meet the requirements of the university, the government and the industry. The SiF feeder model showed the ability to yield positive learning outcomes with low expenditures per student for both the family and the university. In parallel, the sharing of knowledge between university and industry became increasingly important in the process, which resulted in the improvement of industrial skills for professors and an increase in industrial based research for the university. The SiF feeder model meets its demand of public policy in supporting a skilled workforce for the industry, which could be an effective tool for the triple helix educational model of Thailand.

Characterization of vibrissa germinative cells: transition of cell types.

PubMed

Osada, A; Kobayashi, K

2001-12-01

Germinative cells, small cell masses attached to the stalks of dermal papillae that are able to differentiate into the hair shaft and inner root sheath, form follicular bulb-like structures when co-cultured with dermal papilla cells. We studied the growth characteristics of germinative cells to determine the cell types in the vibrissa germinative tissue. Germinative tissues, attaching to dermal papillae, were cultured on 3T3 feeder layers. The cultured keratinocytes were harvested and transferred, equally and for two passages, onto lined dermal papilla cells (LDPC) and/or 3T3 feeder layers. The resulting germinative cells were classified into three types in the present experimental condition. Type 1 cells grow very well on either feeder layer, whereas Type 3 cells scarcely grow on either feeder layer. Type 2 cells are very conspicuous and are reversible. They grow well on 3T3 but growth is suppressed on LDPC feeder layers. The Type 2 cells that grow well on 3T3 feeder layers, however, are suppressed when transferred onto LDPC and the Type 2 cells that are suppressed on LDPC begin to grow again on 3T3. The transition of one cell type to another in vitro and the cell types that these germinative cell types correspond to in vivo is discussed. It was concluded that stem cells or their close progenitors reside in the germinative tissues of the vibrissa bulb except at late anagen-early catagen.

Thermal Imaging for Assessment of Electron-Beam Free Form Fabrication (EBF(sup 3)) Additive Manufacturing Welds

NASA Technical Reports Server (NTRS)

Zalameda, Joseph N.; Burke, Eric R.; Hafley, Robert A.; Taminger, Karen M.; Domack, Christopher S.; Brewer, Amy R.; Martin, Richard E.

2013-01-01

Additive manufacturing is a rapidly growing field where 3-dimensional parts can be produced layer by layer. NASA s electron beam free-form fabrication (EBF(sup 3)) technology is being evaluated to manufacture metallic parts in a space environment. The benefits of EBF(sup 3) technology are weight savings to support space missions, rapid prototyping in a zero gravity environment, and improved vehicle readiness. The EBF(sup 3) system is composed of 3 main components: electron beam gun, multi-axis position system, and metallic wire feeder. The electron beam is used to melt the wire and the multi-axis positioning system is used to build the part layer by layer. To insure a quality weld, a near infrared (NIR) camera is used to image the melt pool and solidification areas. This paper describes the calibration and application of a NIR camera for temperature measurement. In addition, image processing techniques are presented for weld assessment metrics.

Investigating multi-objective fluence and beam orientation IMRT optimization

NASA Astrophysics Data System (ADS)

Potrebko, Peter S.; Fiege, Jason; Biagioli, Matthew; Poleszczuk, Jan

2017-07-01

Radiation Oncology treatment planning requires compromises to be made between clinical objectives that are invariably in conflict. It would be beneficial to have a ‘bird’s-eye-view’ perspective of the full spectrum of treatment plans that represent the possible trade-offs between delivering the intended dose to the planning target volume (PTV) while optimally sparing the organs-at-risk (OARs). In this work, the authors demonstrate Pareto-aware radiotherapy evolutionary treatment optimization (PARETO), a multi-objective tool featuring such bird’s-eye-view functionality, which optimizes fluence patterns and beam angles for intensity-modulated radiation therapy (IMRT) treatment planning. The problem of IMRT treatment plan optimization is managed as a combined monolithic problem, where all beam fluence and angle parameters are treated equally during the optimization. To achieve this, PARETO is built around a powerful multi-objective evolutionary algorithm, called Ferret, which simultaneously optimizes multiple fitness functions that encode the attributes of the desired dose distribution for the PTV and OARs. The graphical interfaces within PARETO provide useful information such as: the convergence behavior during optimization, trade-off plots between the competing objectives, and a graphical representation of the optimal solution database allowing for the rapid exploration of treatment plan quality through the evaluation of dose-volume histograms and isodose distributions. PARETO was evaluated for two relatively complex clinical cases, a paranasal sinus and a pancreas case. The end result of each PARETO run was a database of optimal (non-dominated) treatment plans that demonstrated trade-offs between the OAR and PTV fitness functions, which were all equally good in the Pareto-optimal sense (where no one objective can be improved without worsening at least one other). Ferret was able to produce high quality solutions even though a large number of parameters, such as beam fluence and beam angles, were included in the optimization.

Energy Systems Integration: Data Call -- Become a Data Partner

DOE Office of Scientific and Technical Information (OSTI.GOV)

2017-01-01

This project aims to advance the understanding of costs associated with integrating PV onto the electric power distribution system while maintaining reliable grid operations. We have developed a bottom-up framework for calculating these costs as a function of PV penetration levels on specific feeders. This framework will used to inform and improve utility planning decisions, increase the transparency and speed associated with the interconnection process, and provide policymakers with more information on the total cost of energy from PV.

Voxel-based dose prediction with multi-patient atlas selection for automated radiotherapy treatment planning

NASA Astrophysics Data System (ADS)

McIntosh, Chris; Purdie, Thomas G.

2017-01-01

Automating the radiotherapy treatment planning process is a technically challenging problem. The majority of automated approaches have focused on customizing and inferring dose volume objectives to be used in plan optimization. In this work we outline a multi-patient atlas-based dose prediction approach that learns to predict the dose-per-voxel for a novel patient directly from the computed tomography planning scan without the requirement of specifying any objectives. Our method learns to automatically select the most effective atlases for a novel patient, and then map the dose from those atlases onto the novel patient. We extend our previous work to include a conditional random field for the optimization of a joint distribution prior that matches the complementary goals of an accurately spatially distributed dose distribution while still adhering to the desired dose volume histograms. The resulting distribution can then be used for inverse-planning with a new spatial dose objective, or to create typical dose volume objectives for the canonical optimization pipeline. We investigated six treatment sites (633 patients for training and 113 patients for testing) and evaluated the mean absolute difference in all DVHs for the clinical and predicted dose distribution. The results on average are favorable in comparison to our previous approach (1.91 versus 2.57). Comparing our method with and without atlas-selection further validates that atlas-selection improved dose prediction on average in whole breast (0.64 versus 1.59), prostate (2.13 versus 4.07), and rectum (1.46 versus 3.29) while it is less important in breast cavity (0.79 versus 0.92) and lung (1.33 versus 1.27) for which there is high conformity and minimal dose shaping. In CNS brain, atlas-selection has the potential to be impactful (3.65 versus 5.09), but selecting the ideal atlas is the most challenging.

Complex memories in honeybees: can there be more than two?

PubMed

Reinhard, Judith; Srinivasan, Mandyam V; Zhang, Shaowu

2006-04-01

Foraging honeybees are likely to learn visual and chemical cues associated with many different food sources. Here, we explore how many such sources can be memorized and recalled. Marked bees were trained to visit two (or three) sugar feeders, each placed at a different outdoor location and carrying a different scent. We then tested the ability of the bees to recall these locations and fly to them, when the training scents were blown into the hive, and the scents and food at the feeders were removed. When trained on two feeder locations, each associated with a different scent, the bees could correctly recall the location associated with each scent. However, this ability broke down when the number of scents and feeder locations was increased to three. Performance was partially restored when each of the three training feeders was endowed with an additional cue, namely, a distinct colour. Our results suggest that bees can recall a maximum of two locations when each is associated with a different scent. However, this number can be increased if the scent cues are augmented by visual cues. These findings have implications for the ways in which associations are established and laid down in honeybee memory.

Optic flow informs distance but not profitability for honeybees.

PubMed

Shafir, Sharoni; Barron, Andrew B

2010-04-22

How do flying insects monitor foraging efficiency? Honeybees (Apis mellifera) use optic flow information as an odometer to estimate distance travelled, but here we tested whether optic flow informs estimation of foraging costs also. Bees were trained to feeders in flight tunnels such that bees experienced the greatest optic flow en route to the feeder closest to the hive. Analyses of dance communication showed that, as expected, bees indicated the close feeder as being further, but they also indicated this feeder as the more profitable, and preferentially visited this feeder when given a choice. We show that honeybee estimates of foraging cost are not reliant on optic flow information. Rather, bees can assess distance and profitability independently and signal these aspects as separate elements of their dances. The optic flow signal is sensitive to the nature of the environment travelled by the bee, and is therefore not a good index of flight energetic costs, but it provides a good indication of distance travelled for purpose of navigation and communication, as long as the dancer and recruit travel similar routes. This study suggests an adaptive dual processing system in honeybees for communicating and navigating distance flown and for evaluating its energetic costs.

Optic flow informs distance but not profitability for honeybees

PubMed Central

Shafir, Sharoni; Barron, Andrew B.

2010-01-01

How do flying insects monitor foraging efficiency? Honeybees (Apis mellifera) use optic flow information as an odometer to estimate distance travelled, but here we tested whether optic flow informs estimation of foraging costs also. Bees were trained to feeders in flight tunnels such that bees experienced the greatest optic flow en route to the feeder closest to the hive. Analyses of dance communication showed that, as expected, bees indicated the close feeder as being further, but they also indicated this feeder as the more profitable, and preferentially visited this feeder when given a choice. We show that honeybee estimates of foraging cost are not reliant on optic flow information. Rather, bees can assess distance and profitability independently and signal these aspects as separate elements of their dances. The optic flow signal is sensitive to the nature of the environment travelled by the bee, and is therefore not a good index of flight energetic costs, but it provides a good indication of distance travelled for purpose of navigation and communication, as long as the dancer and recruit travel similar routes. This study suggests an adaptive dual processing system in honeybees for communicating and navigating distance flown and for evaluating its energetic costs. PMID:20018787

Energy efficiency analysis of two-sided feed scheme of DC traction network with high asymmetry of feeders parameters

NASA Astrophysics Data System (ADS)

Abramov, E. Y.; Sopov, V. I.

2017-10-01

In a given research using the example of traction network area with high asymmetry of power supply parameters, the sequence of comparative assessment of power losses in DC traction network with parallel and traditional separated operating modes of traction substation feeders was shown. Experimental measurements were carried out under these modes of operation. The calculation data results based on statistic processing showed the power losses decrease in contact network and the increase in feeders. The changes proved to be critical ones and this demonstrates the significance of potential effects when converting traction network areas into parallel feeder operation. An analytical method of calculation the average power losses for different feed schemes of the traction network was developed. On its basis, the dependences of the relative losses were obtained by varying the difference in feeder voltages. The calculation results showed unreasonableness transition to a two-sided feed scheme for the considered traction network area. A larger reduction in the total power loss can be obtained with a smaller difference of the feeders’ resistance and / or a more symmetrical sectioning scheme of contact network.

Urban and rural habitats differ in number and type of bird feeders and in bird species consuming supplementary food.

PubMed

Tryjanowski, Piotr; Skórka, Piotr; Sparks, Tim H; Biaduń, Waldemar; Brauze, Tomasz; Hetmański, Tomasz; Martyka, Rafał; Indykiewicz, Piotr; Myczko, Łukasz; Kunysz, Przemysław; Kawa, Piotr; Czyż, Stanisław; Czechowski, Paweł; Polakowski, Michał; Zduniak, Piotr; Jerzak, Leszek; Janiszewski, Tomasz; Goławski, Artur; Duduś, Leszek; Nowakowski, Jacek J; Wuczyński, Andrzej; Wysocki, Dariusz

2015-10-01

Bird feeding is one of the most widespread direct interactions between man and nature, and this has important social and environmental consequences. However, this activity can differ between rural and urban habitats, due to inter alia habitat structure, human behaviour and the composition of wintering bird communities. We counted birds in 156 squares (0.25 km(2) each) in December 2012 and again in January 2013 in locations in and around 26 towns and cities across Poland (in each urban area, we surveyed 3 squares and also 3 squares in nearby rural areas). At each count, we noted the number of bird feeders, the number of bird feeders with food, the type of feeders, additional food supplies potentially available for birds (bread offered by people, bins) and finally the birds themselves. In winter, urban and rural areas differ in the availability of food offered intentionally and unintentionally to birds by humans. Both types of food availability are higher in urban areas. Our findings suggest that different types of bird feeder support only those species specialized for that particular food type and this relationship is similar in urban and rural areas.

Development of a pilot-scale kinetic extruder feeder system and test program. Phase II. Verification testing. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1984-01-12

This report describes the work done under Phase II, the verification testing of the Kinetic Extruder. The main objective of the test program was to determine failure modes and wear rates. Only minor auxiliary equipment malfunctions were encountered. Wear rates indicate useful life expectancy of from 1 to 5 years for wear-exposed components. Recommendations are made for adapting the equipment for pilot plant and commercial applications. 3 references, 20 figures, 12 tables.

View northwest, discharge basin, floor, showing cement cross beams built ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View northwest, discharge basin, floor, showing cement cross beams built on stone bases - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY

Multi-Excitation Magnetoacoustic Tomography with Magnetic Induction for Bioimpedance Imaging

PubMed Central

Li, Xu; He, Bin

2011-01-01

Magnetoacoustic tomography with magnetic induction (MAT-MI) is an imaging approach proposed to conduct non-invasive electrical conductivity imaging of biological tissue with high spatial resolution. In the present study, based on the analysis of the relationship between the conductivity distribution and the generated MAT-MI acoustic source, we propose a new multi-excitation MAT-MI approach and the corresponding reconstruction algorithms. In the proposed method, multiple magnetic excitations using different coil configurations are employed and ultrasound measurements corresponding to each excitation are collected to derive the conductivity distribution inside the sample. A modified reconstruction algorithm is also proposed for the multi-excitation MAT-MI imaging approach when only limited bandwidth acoustic measurements are available. Computer simulation and phantom experiment studies have been done to demonstrate the merits of the proposed method. It is shown that if unlimited bandwidth acoustic data is available, we can accurately reconstruct the internal conductivity contrast of an object using the proposed method. With limited bandwidth data and the use of the modified algorithm we can reconstruct the relative conductivity contrast of an object instead of only boundaries at the conductivity heterogeneity. Benefits that come with this new method include better differentiation of tissue types with conductivity contrast using the MAT-MI approach, specifically for potential breast cancer screening application in the future. PMID:20529729

Multi-decadal changes in the megabenthos of the Bay of Fundy: The effects of fishing

NASA Astrophysics Data System (ADS)

Kenchington, Ellen L.; Kenchington, Trevor J.; Henry, Lea-Anne; Fuller, Susanna; Gonzalez, Patricia

2007-10-01

Analysis of presence / absence records from two comparable megabenthic surveys of scallop grounds in the Bay of Fundy, Canada, in 1966-67 and 1997 showed profound change over three decades. There were no indications that any species were lost and the average number of taxa per station remained steady. However, spatial heterogeneities in the community were reduced and species composition changed significantly. Some taxa widespread in 1966-67 declined while others expanded, with frequencies of occurrence of individual taxa changing by up to 71%. The whelks Buccinum undatum and Colus spp., the bivalves Astarte spp. and Cyclocardia borealis, the toad crabs Hyas spp., the sea urchin Strongylocentrotus droebachiensis and the brittle stars (Ophiurida) showed particular increases. Corresponding declines were seen in the boring sponges Cliona spp., the horse mussel Modiolus modiolus, the scallop Chlamys islandica, the fan worm Pseudopotamilla reniformis and the stalked tunicate Boltenia ovifera. Replacement of attached, fragile, epifaunal, filter-feeding taxa by a combination of motile scavengers, motile filter-feeders and robust, burrowing filter-feeders suggests that the primary cause of the temporal change was physical impacts by fishing gear, even though trawling and scallop dragging in the area were neither intense nor new developments. Secondary causes of change may have included other ecosystem effects of fishing (supply of discards and bait), a mass mortality of scallops and a range expansion of a bryozoan ( Flustra foliacea).

Efficient multi-objective calibration of a computationally intensive hydrologic model with parallel computing software in Python

USDA-ARS?s Scientific Manuscript database

With enhanced data availability, distributed watershed models for large areas with high spatial and temporal resolution are increasingly used to understand water budgets and examine effects of human activities and climate change/variability on water resources. Developing parallel computing software...

Modeling Cometary Coma with a Three Dimensional, Anisotropic Multiple Scattering Distributed Processing Code

NASA Technical Reports Server (NTRS)

Luchini, Chris B.

1997-01-01

Development of camera and instrument simulations for space exploration requires the development of scientifically accurate models of the objects to be studied. Several planned cometary missions have prompted the development of a three dimensional, multi-spectral, anisotropic multiple scattering model of cometary coma.

Spacelab 4: Primate experiment support hardware

NASA Astrophysics Data System (ADS)

Fusco, P. R.; Peyran, R. J.

1984-05-01

A squirrel monkey feeder and automatic urine collection system were designed to fly on the Spacelab 4 Shuttle Mission presently scheduled for January 1986. Prototypes of the feeder and urine collection systems were fabricated and extensively tested on squirrel monkeys at the National Aeronautics and Space Administration's (NASA) Ames Research Center (ARC). The feeder design minimizes impact on the monkey's limited space in the cage and features improved reliability and biocompatibility over previous systems. The urine collection system is the first flight qualified, automatic urine collection device for squirrel monkeys. Flight systems are currently being fabricated.

Spacelab 4: Primate experiment support hardware

NASA Technical Reports Server (NTRS)

Fusco, P. R.; Peyran, R. J.

1984-01-01

A squirrel monkey feeder and automatic urine collection system were designed to fly on the Spacelab 4 Shuttle Mission presently scheduled for January 1986. Prototypes of the feeder and urine collection systems were fabricated and extensively tested on squirrel monkeys at the National Aeronautics and Space Administration's (NASA) Ames Research Center (ARC). The feeder design minimizes impact on the monkey's limited space in the cage and features improved reliability and biocompatibility over previous systems. The urine collection system is the first flight qualified, automatic urine collection device for squirrel monkeys. Flight systems are currently being fabricated.

A novel fruit shape classification method based on multi-scale analysis

NASA Astrophysics Data System (ADS)

Gui, Jiangsheng; Ying, Yibin; Rao, Xiuqin

2005-11-01

Shape is one of the major concerns and which is still a difficult problem in automated inspection and sorting of fruits. In this research, we proposed the multi-scale energy distribution (MSED) for object shape description, the relationship between objects shape and its boundary energy distribution at multi-scale was explored for shape extraction. MSED offers not only the mainly energy which represent primary shape information at the lower scales, but also subordinate energy which represent local shape information at higher differential scales. Thus, it provides a natural tool for multi resolution representation and can be used as a feature for shape classification. We addressed the three main processing steps in the MSED-based shape classification. They are namely, 1) image preprocessing and citrus shape extraction, 2) shape resample and shape feature normalization, 3) energy decomposition by wavelet and classification by BP neural network. Hereinto, shape resample is resample 256 boundary pixel from a curve which is approximated original boundary by using cubic spline in order to get uniform raw data. A probability function was defined and an effective method to select a start point was given through maximal expectation, which overcame the inconvenience of traditional methods in order to have a property of rotation invariants. The experiment result is relatively well normal citrus and serious abnormality, with a classification rate superior to 91.2%. The global correct classification rate is 89.77%, and our method is more effective than traditional method. The global result can meet the request of fruit grading.

Price Incentivised Electric Vehicle Charge Control for Community Voltage Regulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kelly, Damian; Baroncelli, Fabio; Fowler, Christopher

2014-11-03

With the growing availability of Electric Vehicles, there is a significant opportunity to use battery 'smart-charging' for voltage regulation. This work designs and experimentally evaluates a system for price-incentivised electric vehicle charging. The system is designed to eliminate negative impacts to the user while minimising the cost of charging and achieving a more favourable voltage behaviour throughout the local grid over time. The practical issues associated with a real-life deployment are identified and resolved. The efficacy of the system is evaluated in the challenging scenario in which EVs are deployed in six closely distributed homes, serviced by the same lowmore » voltage residential distribution feeder.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zamzam, Ahmed, S.; Zhaoy, Changhong; Dall'Anesey, Emiliano

This paper examines the AC Optimal Power Flow (OPF) problem for multiphase distribution networks featuring renewable energy resources (RESs). We start by outlining a power flow model for radial multiphase systems that accommodates wye-connected and delta-connected RESs and non-controllable energy assets. We then formalize an AC OPF problem that accounts for both types of connections. Similar to various AC OPF renditions, the resultant problem is a non convex quadratically-constrained quadratic program. However, the so-called Feasible Point Pursuit-Successive Convex Approximation algorithm is leveraged to obtain a feasible and yet locally-optimal solution. The merits of the proposed solution approach are demonstrated usingmore » two unbalanced multiphase distribution feeders with both wye and delta connections.« less

Recombinant rabbit leukemia inhibitory factor and rabbit embryonic fibroblasts support the derivation and maintenance of rabbit embryonic stem cells.

PubMed

Xue, Fei; Ma, Yinghong; Chen, Y Eugene; Zhang, Jifeng; Lin, Tzu-An; Chen, Chien-Hong; Lin, Wei-Wen; Roach, Marsha; Ju, Jyh-Cherng; Yang, Lan; Du, Fuliang; Xu, Jie

2012-08-01

The rabbit is a classical experimental animal species. A major limitation in using rabbits for biomedical research is the lack of germ-line-competent rabbit embryonic stem cells (rbESCs). We hypothesized that the use of homologous feeder cells and recombinant rabbit leukemia inhibitory factor (rbLIF) might improve the chance in deriving germ-line-competent rbES cells. In the present study, we established rabbit embryonic fibroblast (REF) feeder layers and synthesized recombinant rbLIF. We derived a total of seven putative rbESC lines, of which two lines (M5 and M23) were from culture Condition I using mouse embryonic fibroblasts (MEFs) as feeders supplemented with human LIF (hLIF) (MEF+hLIF). Another five lines (R4, R9, R15, R21, and R31) were derived from Condition II using REFs as feeder cells supplemented with rbLIF (REF+rbLIF). Similar derivation efficiency was observed between these two conditions (8.7% vs. 10.2%). In a separate experiment with 2×3 factorial design, we examined the effects of feeder cells (MEF vs. REF) and LIFs (mLIF, hLIF vs. rbLIF) on rbESC culture. Both Conditions I and II supported satisfactory rbESC culture, with similar or better population doubling time and colony-forming efficiency than other combinations of feeder cells with LIFs. Rabbit ESCs derived and maintained on both conditions displayed typical ESC characteristics, including ESC pluripotency marker expression (AP, Oct4, Sox2, Nanog, and SSEA4) and gene expression (Oct4, Sox2, Nanog, c-Myc, Klf4, and Dppa5), and the capacity to differentiate into three primary germ layers in vitro. The present work is the first attempt to establish rbESC lines using homologous feeder cells and recombinant rbLIF, by which the rbESCs were derived and maintained normally. These cell lines are unique resources and may facilitate the derivation of germ-line-competent rbESCs.

Active illuminated space object imaging and tracking simulation

NASA Astrophysics Data System (ADS)

Yue, Yufang; Xie, Xiaogang; Luo, Wen; Zhang, Feizhou; An, Jianzhu

2016-10-01

Optical earth imaging simulation of a space target in orbit and it's extraction in laser illumination condition were discussed. Based on the orbit and corresponding attitude of a satellite, its 3D imaging rendering was built. General simulation platform was researched, which was adaptive to variable 3D satellite models and relative position relationships between satellite and earth detector system. Unified parallel projection technology was proposed in this paper. Furthermore, we denoted that random optical distribution in laser-illuminated condition was a challenge for object discrimination. Great randomicity of laser active illuminating speckles was the primary factor. The conjunction effects of multi-frame accumulation process and some tracking methods such as Meanshift tracking, contour poid, and filter deconvolution were simulated. Comparison of results illustrates that the union of multi-frame accumulation and contour poid was recommendable for laser active illuminated images, which had capacities of high tracking precise and stability for multiple object attitudes.

View southeast, interior of second drop, foundation and footwall and ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

View southeast, interior of second drop, foundation and footwall and sidewalls, showing failed lower arch - Glens Falls Feeder, Sluice, Along south side of Glens Falls Feeder between locks 10 & 20, Hudson Falls, Washington County, NY

Mass extinctions: Ecological selectivity and primary production

NASA Astrophysics Data System (ADS)

Rhodes, Melissa Clark; Thayer, Charles W.

1991-09-01

If mass extinctions were caused by reduced primary productivity, then extinctions should be concentrated among animals with starvation-susceptible feeding modes, active lifestyles, and high-energy budgets. The stratigraphic ranges (by stage) of 424 genera of bivalves and 309 genera of articulate brachiopods suggest that there was an unusual reduction of primary productivity at the Cretaceous/Tertiary (K/T) boundary extinction. For bivalves at the K/T, there were (1) selective extinction of suspension feeders and other susceptible trophic categories relative to deposit feeders and other resistant categories, and (2) among suspension feed-ers, selective extinction of bivalves with active locomotion. During the Permian-Triassic (P/Tr) extinction and Jurassic background time, extinction rates among suspension feeders were greater for articulate brachiopods than for bivalves. But during the K/T event, extinction rates of articulates and suspension-feeding bivalves equalized, possibly because the low-energy budgets of articulates gave them an advantage when food was scarce.

Relationships between species feeding traits and environmental conditions in fish communities: a three-matrix approach.

PubMed

Brind'Amour, Anik; Boisclair, Daniel; Dray, Stéphane; Legendre, Pierre

2011-03-01

Understanding the relationships between species biological traits and the environment is crucial to predicting the effect of habitat perturbations on fish communities. It is also an essential step in the assessment of the functional diversity. Using two complementary three-matrix approaches (fourth-corner and RLQ analyses), we tested the hypothesis that feeding-oriented traits determine the spatial distributions of littoral fish species by assessing the relationship between fish spatial distributions, fish species traits, and habitat characteristics in two Laurentian Shield lakes. Significant associations between the feeding-oriented traits and the environmental characteristics suggested that fish communities in small lakes (displaying low species richness) can be spatially structured. Three groups of traits, mainly categorized by the species spatial and temporal feeding activity, were identified. The water column may be divided in two sections, each of them corresponding to a group of traits related to the vertical distribution of the prey coupled with the position of the mouth. Lake areas of low structural complexity were inhabited by functional assemblages dominated by surface feeders while structurally more complex areas were occupied by mid-water and benthic feeders. A third group referring to the time of feeding activity was observed. Our work could serve as a guideline study to evaluate species traits x environment associations at multiple spatial scales. Our results indicate that three-matrix statistical approaches are powerful tools that can be used to study such relationships. These recent statistical approaches open up new research directions such as the study of spatially based biological functions in lakes. They also provide new analytical tools for determining, for example, the potential size of freshwater protected areas.

A Hierarchical Modeling for Reactive Power Optimization With Joint Transmission and Distribution Networks by Curve Fitting

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ding, Tao; Li, Cheng; Huang, Can

Here, in order to solve the reactive power optimization with joint transmission and distribution networks, a hierarchical modeling method is proposed in this paper. It allows the reactive power optimization of transmission and distribution networks to be performed separately, leading to a master–slave structure and improves traditional centralized modeling methods by alleviating the big data problem in a control center. Specifically, the transmission-distribution-network coordination issue of the hierarchical modeling method is investigated. First, a curve-fitting approach is developed to provide a cost function of the slave model for the master model, which reflects the impacts of each slave model. Second,more » the transmission and distribution networks are decoupled at feeder buses, and all the distribution networks are coordinated by the master reactive power optimization model to achieve the global optimality. Finally, numerical results on two test systems verify the effectiveness of the proposed hierarchical modeling and curve-fitting methods.« less

A Hierarchical Modeling for Reactive Power Optimization With Joint Transmission and Distribution Networks by Curve Fitting

DOE PAGES

Ding, Tao; Li, Cheng; Huang, Can; ...

2017-01-09

Here, in order to solve the reactive power optimization with joint transmission and distribution networks, a hierarchical modeling method is proposed in this paper. It allows the reactive power optimization of transmission and distribution networks to be performed separately, leading to a master–slave structure and improves traditional centralized modeling methods by alleviating the big data problem in a control center. Specifically, the transmission-distribution-network coordination issue of the hierarchical modeling method is investigated. First, a curve-fitting approach is developed to provide a cost function of the slave model for the master model, which reflects the impacts of each slave model. Second,more » the transmission and distribution networks are decoupled at feeder buses, and all the distribution networks are coordinated by the master reactive power optimization model to achieve the global optimality. Finally, numerical results on two test systems verify the effectiveness of the proposed hierarchical modeling and curve-fitting methods.« less

Subjective value of risky foods for individual domestic chicks: a hierarchical Bayesian model.

PubMed

Kawamori, Ai; Matsushima, Toshiya

2010-05-01

For animals to decide which prey to attack, the gain and delay of the food item must be integrated in a value function. However, the subjective value is not obtained by expected profitability when it is accompanied by risk. To estimate the subjective value, we examined choices in a cross-shaped maze with two colored feeders in domestic chicks. When tested by a reversal in food amount or delay, chicks changed choices similarly in both conditions (experiment 1). We therefore examined risk sensitivity for amount and delay (experiment 2) by supplying one feeder with food of fixed profitability and the alternative feeder with high- or low-profitability food at equal probability. Profitability varied in amount (groups 1 and 2 at high and low variance) or in delay (group 3). To find the equilibrium, the amount (groups 1 and 2) or delay (group 3) of the food in the fixed feeder was adjusted in a total of 18 blocks. The Markov chain Monte Carlo method was applied to a hierarchical Bayesian model to estimate the subjective value. Chicks undervalued the variable feeder in group 1 and were indifferent in group 2 but overvalued the variable feeder in group 3 at a population level. Re-examination without the titration procedure (experiment 3) suggested that the subjective value was not absolute for each option. When the delay was varied, the variable option was often given a paradoxically high value depending on fixed alternative. Therefore, the basic assumption of the uniquely determined value function might be questioned.

Feeder systems of acidic lava flows from the Paraná-Etendeka Igneous Province in southern Brazil and their implications for eruption style

NASA Astrophysics Data System (ADS)

de Lima, Evandro Fernandes; Waichel, Breno Leitão; Rossetti, Lucas De Magalhães May; Sommer, Carlos Augusto; Simões, Matheus Silva

2018-01-01

In the Rio Grande do Sul State, southern Brazil, the volcanic sequence of the Paraná-Etendeka Igneous Province consists of pahoehoe and rubbly pahoehoe lava flows with basaltic and basaltic andesitic composition respectively, overlaid by acidic volcanic rocks. The acidic volcanic rocks of the Paraná-Etendeka Igneous Province exhibit textures and structures that can be related to effusive and/or explosive eruptions generating predominantly rheoignimbrites. The huge lava volume related to the emplacement of large igneous provinces implicates on efficient feeder systems that are more commonly observed in continental environments. In the Paraná-Etendeka Igneous Province, feeders of basaltic rocks are exposed in several dyke swarms (Ponta Grossa NW trending, Florianópolis/Skeleton Coast (NW Namibia) N-S trending, Serra do Mar NE trending and Henties Bay/Outjo NE trending). In contrast, the only feeder system proposed to the acidic rocks of the Paraná-Etendeka Igneous Province is the Messum complex in Namibia (Milner et al. 1995). In the study area, the opening of three quarries for the extraction of dimension stones has exposed impressive structures/textures that show the effusive emplacement and the ductile to fragile-ductile magma transition along the acidic feeder dykes. Besides that, magma mixing/mingling processes between two acidic magmas are observed along the dykes. Here we describe new occurrences of acidic feeder dykes, correlate the dykes with acidic flows and discuss their importance to understand the emplacement of the Palmas type acid units in southern Brazil.

2. Photocopy of a drawing (original in the Collection of ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Photocopy of a drawing (original in the Collection of the PL&C, Shelf 117, Drawing 155) SECTION OF THE MOODY STREET FEEDER, DECEMBER 30, 1847 - Moody Street Feeder, Moody Street vicinity, Lowell, Middlesex County, MA

30 CFR 77.1801 - Overcurrent protection.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Overcurrent protection. 77.1801 Section 77.1801... Wires and Trolley Feeder Wires § 77.1801 Overcurrent protection. Trolley wires and trolley feeder wires shall be provided with overcurrent protection. ...

Impact of Spatial Pumping Patterns on Groundwater Management

NASA Astrophysics Data System (ADS)

Yin, J.; Tsai, F. T. C.

2017-12-01

Challenges exist to manage groundwater resources while maintaining a balance between groundwater quantity and quality because of anthropogenic pumping activities as well as complex subsurface environment. In this study, to address the impact of spatial pumping pattern on groundwater management, a mixed integer nonlinear multi-objective model is formulated by integrating three objectives within a management framework to: (i) maximize total groundwater withdrawal from potential wells; (ii) minimize total electricity cost for well pumps; and (iii) attain groundwater level at selected monitoring locations as close as possible to the target level. Binary variables are used in the groundwater management model to control the operative status of pumping wells. The NSGA-II is linked with MODFLOW to solve the multi-objective problem. The proposed method is applied to a groundwater management problem in the complex Baton Rouge aquifer system, southeastern Louisiana. Results show that (a) non-dominated trade-off solutions under various spatial distributions of active pumping wells can be achieved. Each solution is optimal with regard to its corresponding objectives; (b) operative status, locations and pumping rates of pumping wells are significant to influence the distribution of hydraulic head, which in turn influence the optimization results; (c) A wide range of optimal solutions is obtained such that decision makers can select the most appropriate solution through negotiation with different stakeholders. This technique is beneficial to finding out the optimal extent to which three objectives including water supply concern, energy concern and subsidence concern can be balanced.

Desired Precision in Multi-Objective Optimization: Epsilon Archiving or Rounding Objectives?

NASA Astrophysics Data System (ADS)

Asadzadeh, M.; Sahraei, S.

2016-12-01

Multi-objective optimization (MO) aids in supporting the decision making process in water resources engineering and design problems. One of the main goals of solving a MO problem is to archive a set of solutions that is well-distributed across a wide range of all the design objectives. Modern MO algorithms use the epsilon dominance concept to define a mesh with pre-defined grid-cell size (often called epsilon) in the objective space and archive at most one solution at each grid-cell. Epsilon can be set to the desired precision level of each objective function to make sure that the difference between each pair of archived solutions is meaningful. This epsilon archiving process is computationally expensive in problems that have quick-to-evaluate objective functions. This research explores the applicability of a similar but computationally more efficient approach to respect the desired precision level of all objectives in the solution archiving process. In this alternative approach each objective function is rounded to the desired precision level before comparing any new solution to the set of archived solutions that already have rounded objective function values. This alternative solution archiving approach is compared to the epsilon archiving approach in terms of efficiency and quality of archived solutions for solving mathematical test problems and hydrologic model calibration problems.

Teamwork Reasoning and Multi-Satellite Missions

NASA Technical Reports Server (NTRS)

Marsella, Stacy C.; Plaunt, Christian (Technical Monitor)

2002-01-01

NASA is rapidly moving towards the use of spatially distributed multiple satellites operating in near Earth orbit and Deep Space. Effective operation of such multi-satellite constellations raises many key research issues. In particular, the satellites will be required to cooperate with each other as a team that must achieve common objectives with a high degree of autonomy from ground based operations. The multi-agent research community has made considerable progress in investigating the challenges of realizing such teamwork. In this report, we discuss some of the teamwork issues that will be faced by multi-satellite operations. The basis of the discussion is a particular proposed mission, the Magnetospheric MultiScale mission to explore Earth's magnetosphere. We describe this mission and then consider how multi-agent technologies might be applied in the design and operation of these missions. We consider the potential benefits of these technologies as well as the research challenges that will be raised in applying them to NASA multi-satellite missions. We conclude with some recommendations for future work.

Compiling for Application Specific Computational Acceleration in Reconfigurable Architectures Final Report CRADA No. TSB-2033-01

DOE Office of Scientific and Technical Information (OSTI.GOV)

De Supinski, B.; Caliga, D.

2017-09-28

The primary objective of this project was to develop memory optimization technology to efficiently deliver data to, and distribute data within, the SRC-6's Field Programmable Gate Array- ("FPGA") based Multi-Adaptive Processors (MAPs). The hardware/software approach was to explore efficient MAP configurations and generate the compiler technology to exploit those configurations. This memory accessing technology represents an important step towards making reconfigurable symmetric multi-processor (SMP) architectures that will be a costeffective solution for large-scale scientific computing.

Dairy farms testing positive for Mycobacterium avium ssp. paratuberculosis have poorer hygiene practices and are less cautious when purchasing cattle than test-negative herds.

PubMed

Wolf, R; Barkema, H W; De Buck, J; Orsel, K

2016-06-01

Mycobacterium avium ssp. paratuberculosis (MAP), the causative agent of Johne's disease, is present on most dairy farms in Alberta, causing economic losses and presenting a potential public health concern. The objective of this cross-sectional study was to identify risk factors for Alberta dairy herds being MAP-positive based on environmental samples (ES). Risk assessments were conducted and ES were collected on 354 Alberta dairy farms (62% of eligible producers) voluntarily participating in the Alberta Johne's Disease Initiative. In univariate logistic regression, risk factors addressing animal and pen hygiene, as well as the use of feeding equipment to remove manure and manure application on pastures, were all associated with the number of positive ES. Furthermore, based on factor analysis, risk factors were clustered and could be summarized as 4 independent factors: (1) animal, pen, and feeder contamination; (2) shared equipment and pasture contamination; (3) calf diet; and (4) cattle purchase. Using these factor scores as independent variables in multivariate logistic regression models, a 1-unit increase in animal, pen, and feeder contamination resulted in 1.31 times higher odds of having at least 1 positive ES. Furthermore, a 1-unit increase in cattle purchase also resulted in 1.31 times the odds of having at least 1 positive ES. Finally, a 100-cow increase in herd size resulted in an odds ratio of 2.1 for having at least 1 positive ES. In conclusion, cleanliness of animals, pens, and feeders, as well as cattle purchase practices, affected risk of herd infection with MAP. Therefore, improvements in those management practices should be the focus of effective tools to control MAP on dairy farms. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Domestic pigs' (Sus scrofa domestica) use of direct and indirect visual and auditory cues in an object choice task.

PubMed

Nawroth, Christian; von Borell, Eberhard

2015-05-01

Recently, foraging strategies have been linked to the ability to use indirect visual information. More selective feeders should express a higher aversion against losses compared to non-selective feeders and should therefore be more prone to avoid empty food locations. To extend these findings, in this study, we present a series of studies investigating the use of direct and indirect visual and auditory information by an omnivorous but selective feeder-the domestic pig. Subjects had to choose between two buckets, with only one containing a reward. Before making a choice, the subjects in Experiment 1 (N = 8) received full information regarding both the baited and non-baited location, either in a visual or auditory domain. In this experiment, the subjects were able to use visual but not auditory cues to infer the location of the reward spontaneously. Additionally, four individuals learned to use auditory cues after a period of training. In Experiment 2 (N = 8), the pigs were given different amounts of visual information about the content of the buckets-lifting either both of the buckets (full information), the baited bucket (direct information), the empty bucket (indirect information) or no bucket at all (no information). The subjects as a group were able to use direct and indirect visual cues. However, over the course of the experiment, the performance dropped to chance level when indirect information was provided. A final experiment (N = 3) provided preliminary results for pigs' use of indirect auditory information to infer the location of a reward. We conclude that pigs at a very young age are able to make decisions based on indirect information in the visual domain, whereas their performance in the use of indirect auditory information warrants further investigation.

Multi-scale image segmentation method with visual saliency constraints and its application

NASA Astrophysics Data System (ADS)

Chen, Yan; Yu, Jie; Sun, Kaimin

2018-03-01

Object-based image analysis method has many advantages over pixel-based methods, so it is one of the current research hotspots. It is very important to get the image objects by multi-scale image segmentation in order to carry out object-based image analysis. The current popular image segmentation methods mainly share the bottom-up segmentation principle, which is simple to realize and the object boundaries obtained are accurate. However, the macro statistical characteristics of the image areas are difficult to be taken into account, and fragmented segmentation (or over-segmentation) results are difficult to avoid. In addition, when it comes to information extraction, target recognition and other applications, image targets are not equally important, i.e., some specific targets or target groups with particular features worth more attention than the others. To avoid the problem of over-segmentation and highlight the targets of interest, this paper proposes a multi-scale image segmentation method with visually saliency graph constraints. Visual saliency theory and the typical feature extraction method are adopted to obtain the visual saliency information, especially the macroscopic information to be analyzed. The visual saliency information is used as a distribution map of homogeneity weight, where each pixel is given a weight. This weight acts as one of the merging constraints in the multi- scale image segmentation. As a result, pixels that macroscopically belong to the same object but are locally different can be more likely assigned to one same object. In addition, due to the constraint of visual saliency model, the constraint ability over local-macroscopic characteristics can be well controlled during the segmentation process based on different objects. These controls will improve the completeness of visually saliency areas in the segmentation results while diluting the controlling effect for non- saliency background areas. Experiments show that this method works better for texture image segmentation than traditional multi-scale image segmentation methods, and can enable us to give priority control to the saliency objects of interest. This method has been used in image quality evaluation, scattered residential area extraction, sparse forest extraction and other applications to verify its validation. All applications showed good results.

Investigation of the milling capabilities of the F10 Fine Grind mill using Box-Behnken designs.

PubMed

Tan, Bernice Mei Jin; Tay, Justin Yong Soon; Wong, Poh Mun; Chan, Lai Wah; Heng, Paul Wan Sia

2015-01-01

Size reduction or milling of the active is often the first processing step in the design of a dosage form. The ability of a mill to convert coarse crystals into the target size and size distribution efficiently is highly desirable as the quality of the final pharmaceutical product after processing is often still dependent on the dimensional attributes of its component constituents. The F10 Fine Grind mill is a mechanical impact mill designed to produce unimodal mid-size particles by utilizing a single-pass two-stage size reduction process for fine grinding of raw materials needed in secondary processing. Box-Behnken designs were used to investigate the effects of various mill variables (impeller, blower and feeder speeds and screen aperture size) on the milling of coarse crystals. Response variables included the particle size parameters (D10, D50 and D90), span and milling rate. Milled particles in the size range of 5-200 μm, with D50 ranging from 15 to 60 μm, were produced. The impeller and feeder speeds were the most critical factors influencing the particle size and milling rate, respectively. Size distributions of milled particles were better described by their goodness-of-fit to a log-normal distribution (i.e. unimodality) rather than span. Milled particles with symmetrical unimodal distributions were obtained when the screen aperture size was close to the median diameter of coarse particles employed. The capacity for high throughput milling of particles to a mid-size range, which is intermediate between conventional mechanical impact mills and air jet mills, was demonstrated in the F10 mill. Prediction models from the Box-Behnken designs will aid in providing a better guide to the milling process and milled product characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

Code of Federal Regulations, 2014 CFR

2014-10-01

... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...

47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

Code of Federal Regulations, 2012 CFR

2012-10-01

... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...

47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

Code of Federal Regulations, 2010 CFR

2010-10-01

... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...

47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

Code of Federal Regulations, 2011 CFR

2011-10-01

... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...

47 CFR 25.147 - Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz.

Code of Federal Regulations, 2013 CFR

2013-10-01

... COMMISSION (CONTINUED) COMMON CARRIER SERVICES SATELLITE COMMUNICATIONS Applications and Licenses Space Stations § 25.147 Licensing provision for NGSO MSS feeder downlinks in the band 6700-6875 MHz. If an NGSO...

Evaluation of Advanced Microwave Landing System Procedures in the New York Terminal Area

DTIC Science & Technology

1991-03-01

sector controller called the CAMRN sector who must then sequence that traffic with multiple feeders from the south before handing off to the final...Right (13R) were all being used by landing traffic, the final controller handled the runway 22 arrivals and the CAMRN controller handled the runway 13R...Feeder Fix AAL678 DC10 H 00:09:00 AAL68 B767 H 00:23:00 AAL588 A300 H 00:27:00 PAA224 A300 H 01:20:00 4/ TWAll L101 H 01:34:00 CAMRN Feeder Fix DAL144

Vertical-Screw-Auger Conveyer Feeder

NASA Technical Reports Server (NTRS)

Walton, Otis (Inventor); Vollmer, Hubert J. (Inventor)

2016-01-01

A conical feeder is attached to a vertically conveying screw auger. The feeder is equipped with scoops and rotated from the surface to force-feed regolith the auger. Additional scoops are possible by adding a cylindrical section above the conical funnel section. Such then allows the unit to collect material from swaths larger in diameter than the enclosing casing pipe of the screw auger. A third element includes a flexible screw auger. All three can be used in combination in microgravity and zero atmosphere environments to drill and recover a wide area of subsurface regolith and entrained volatiles through a single access point on the surface.

Microstrip Patch Antenna And Method

NASA Technical Reports Server (NTRS)

Fink, Patrick W. (Inventor)

2001-01-01

Method and apparatus are provided for a microstrip feeder structure for supplying properly phased signals to each radiator element in a microstrip antenna array that may be utilized for radiating circularly polarized electromagnetic waves. In one disclosed embodiment. the microstrip feeder structure includes a plurality of microstrip sections many or all of which preferably have an electrical length substantially equal to one-quarter wavelength at the antenna operating frequency. The feeder structure provides a low loss feed structure that may be duplicated multiple times through a set of rotations and translations to provide a radiating array of the desired size.