High performace silicon 2x2 optical switch based on a thermo-optically tunable multimode interference coupler and efficient electrodes.

PubMed

Rosa, Álvaro; Gutiérrez, Ana; Brimont, Antoine; Griol, Amadeu; Sanchis, Pablo

2016-01-11

Optical switches based on tunable multimode interference (MMI) couplers can simultaneously reduce the footprint and increase the tolerance against fabrication deviations. Here, a compact 2x2 silicon switch based on a thermo-optically tunable MMI structure with a footprint of only 0.005 mm(2) is proposed and demonstrated. The MMI structure has been optimized using a silica trench acting as a thermal isolator without introducing any substantial loss penalty or crosstalk degradation. Furthermore, the electrodes performance have significantly been improved via engineering the heater geometry and using two metallization steps. Thereby, a drastic power consumption reduction of around 90% has been demonstrated yielding to values as low as 24.9 mW. Furthermore, very fast switching times of only 1.19 µs have also been achieved.

A compact thermo-optical multimode-interference silicon-based 1 × 4 nano-photonic switch.

PubMed

Zhou, Haifeng; Song, Junfeng; Chee, Edward K S; Li, Chao; Zhang, Huijuan; Lo, Guoqiang

2013-09-09

An ultra-compact multimode-interference (MMI)-based 1 × 4 nano-photonic switch is demonstrated by employing silicon thermo-optical effect on SOI platform. The device performance is systematically characterized by comprehensively investigating the constituent building blocks, including 1 × 4 power splitter, 4 × 4 MMI coupler and groove-isolated thermo-optical heaters. An instructive model is established to statistically estimate the required power consumption and investigate the influence of the power imbalance of the 4 × 4 MMI coupler on the switching performance. At the designed wavelength of 1550 nm, the average insertion loss of different switching states is 1.7 dB, and the transmission imbalance is 1.05 dB. The worst extinction ratio and crosstalk of all the output ports reach 11.48 dB and -11.38 dB, respectively.

Integrated-optic current sensors with a multimode interference waveguide device.

PubMed

Kim, Sung-Moon; Chu, Woo-Sung; Kim, Sang-Guk; Oh, Min-Cheol

2016-04-04

Optical current sensors based on polarization-rotated reflection interferometry are demonstrated using polymeric integrated optics and various functional optical waveguide devices. Interferometric sensors normally require bias feedback control for maintaining the operating point, which increases the cost. In order to resolve this constraint of feedback control, a multimode interference (MMI) waveguide device is integrated onto the current-sensor optical chip in this work. From the multiple outputs of the MMI, a 90° phase-shifted transfer function is obtained. Using passive quadrature demodulation, we demonstrate that the sensor could maintain the output signal regardless of the drift in the operating bias-point.

Spatial mode filters realized with multimode interference couplers

NASA Astrophysics Data System (ADS)

Leuthold, J.; Hess, R.; Eckner, J.; Besse, P. A.; Melchior, H.

1996-06-01

Spatial mode filters based on multimode interference couplers (MMI's) that offer the possibility of splitting off antisymmetric from symmetric modes are presented, and realizations of these filters in InGaAsP / InP are demonstrated. Measured suppression of the antisymmetric first-order modes at the output for the symmetric mode is better than 18 dB. Such MMI's are useful for monolithically integrating mode filters with all-optical devices, which are controlled through an antisymmetric first-order mode. The filtering out of optical control signals is necessary for cascading all-optical devices. Another application is the improvement of on-off ratios in optical switches.

Arbitrary-ratio power splitter based on nonlinear multimode interference coupler

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tajaldini, Mehdi; Young Researchers and Elite Club, Baft Branch, Islamic Azad University, Baft; Jafri, Mohd Zubir Mat

2015-04-24

We propose an ultra-compact multimode interference (MMI) power splitter based on nonlinear effects from simulations using nonlinear modal propagation analysis (NMPA) cooperation with finite difference Method (FDM) to access free choice of splitting ratio. Conventional multimode interference power splitter could only obtain a few discrete ratios. The power splitting ratio may be adjusted continuously while the input set power is varying by a tunable laser. In fact, using an ultra- compact MMI with a simple structure that is launched by a tunable nonlinear input fulfills the problem of arbitrary-ratio in integrated photonics circuits. Silicon on insulator (SOI) is used asmore » the offered material due to the high contrast refractive index and Centro symmetric properties. The high-resolution images at the end of the multimode waveguide in the simulated power splitter have a high power balance, whereas access to a free choice of splitting ratio is not possible under the linear regime in the proposed length range except changes in the dimension for any ratio. The compact dimensions and ideal performance of the device are established according to optimized parameters. The proposed regime can be extended to the design of M×N arbitrary power splitters ratio for programmable logic devices in all optical digital signal processing. The results of this study indicate that nonlinear modal propagation analysis solves the miniaturization problem for all-optical devices based on MMI couplers to achieve multiple functions in a compact planar integrated circuit and also overcomes the limitations of previously proposed methods for nonlinear MMI.« less

Fiber Optic Temperature Sensor Based on Multimode Interference Effects

NASA Astrophysics Data System (ADS)

Aguilar-Soto, J. G.; Antonio-Lopez, J. E.; Sanchez-Mondragon, J. J.; May-Arrioja, D. A.

2011-01-01

A novel fiber optic temperature sensor based on multimode interference was designed, fabricated and tested. The sensor is very simple and inexpensive since we only need to splice a section of multimode fiber between two single mode fibers. Using this device a sensing range of 25°C to 375°C is demonstrated. We should also highlight that due to the pass-band filter response of MMI devices, multiplexing is rather simple by just changing the length of the multimode section.

Proposal of ultra-compact NAND/NOR/XNOR all-optical logic gates based on a nonlinear 3x1 multimode interference

NASA Astrophysics Data System (ADS)

Tajaldini, Mehdi; Mat Jafri, M. Z.

2014-05-01

We present a highly miniaturized multimode interference (MMI) coupler based on nonlinear modal propagation analysis (NMPA) method as a novel design method and potential application for optical NAND, NOR and XNOR logic gates for Boolean logic signal processing devices. Crystalline polydiacetylene is used to allow the appearances of nonlinear effects in low input intensities and ultra- short length to control the MMI coupler as an active device to access light switching due to its high nonlinear susceptibility. We consider a 10x33 μm2 MMI structure with three inputs and one output. Notably, the access facets are single-mode waveguides with sub-micron width. The center input contributes to control the induced light propagation in MMI by intensity variation whereas others could be launched by particular intensity when they are ON and 0 in OFF. Output intensity is analyzed in various sets of inputs to show the capability of Boolean logic gates, the contrast between ON and OFF is calculated on mentioned gates to present the efficiency. Good operation in low intensity and highly miniaturized MMI coupler is observed. Furthermore, nonlinear effects could be realized through the modal interferences. The issue of high insertion loss is addressed with a 3×3 upgraded coupler. Furthermore, the main significant aspect of this paper is simulating an MMI coupler that is launched by three nonlinear inputs, simultaneously, whereas last presents have never studied more than one input in nonlinear regimes.

A novel wavelength multiplexer/demutiplexer based on side-port multimode interference coupler

NASA Astrophysics Data System (ADS)

Wei, Shile; Jian, Wu; Zhao, Lingjuan; Qiu, Jifang; Yin, Zuoshan; Hui, Rongqing

2014-05-01

Based on side-port multimode interference coupler, a novel design of 1.31/1.55-μm wavelength multiplexer/demutiplexer on SOI platform with conventional channel waveguides is proposed and analyzed by using wide-angle beam propagation method. With a 25.9μm long ultra-short MMI section, nearly an order of magnitude shorter than that of the previously reported 1.31/1.55-μm wavelength MMI splitters on SOI, simulation results exhibit contrasts of 28dB and 25dB at wavelength 1.31 and 1.55 μm, respectively, and the insertion losses are both below 0.55dB. Meanwhile, the analysis shows that the proposed structure has larger fabrication tolerances than restricted MMI based structures and the present design methodology also applies to split other wavelengths and in different material platforms, such as InP, GaAs and PLC guides, etc.

Synthesis of Hadamard transformers by use of multimode interference optical waveguides.

PubMed

Gupta, Atma Ram; Tsutsumi, Kiyoshi; Nakayama, Junichi

2003-05-20

We propose a synthesis method of optical Hadamard transformer using multimode interference (MMI) couplers. By using the signal transfer matrix of 2 x 2, 4 x 4, and 8 x 8 MMI couplers, we show that sum and difference units of input signals can be synthesized. An interchange unit of two signals can also be synthesized. One synthesis method of Hadamard transformers is a combination of only 2 x 2 units, and the other is a combination of N x N(N > or = 4) units as well as 2 x 2 units. The design examples of operation units are shown, and the size and the output power of Hadamard transformers are estimated.

Gasohol Quality Control for Real Time Applications by Means of a Multimode Interference Fiber Sensor

PubMed Central

Rodríguez Rodríguez, Adolfo J.; Baldovino-Pantaleón, Oscar; Domínguez Cruz, Rene F.; Zamarreño, Carlos R.; Matías, Ignacio R.; May-Arrioja, Daniel A.

2014-01-01

In this work we demonstrate efficient quality control of a variety of gasoline and ethanol (gasohol) blends using a multimode interference (MMI) fiber sensor. The operational principle relies on the fact that the addition of ethanol to the gasohol blend reduces the refractive index (RI) of the gasoline. Since MMI sensors are capable of detecting small RI changes, the ethanol content of the gasohol blend is easily determined by tracking the MMI peak wavelength response. Gasohol blends with ethanol contents ranging from 0% to 50% has been clearly identified using this device, which provides a linear response with a maximum sensitivity of 0.270 nm/% EtOH. The sensor can also distinguish when water incorporated in the blend has exceeded the maximum volume tolerated by the gasohol blend, which is responsible for phase separation of the ethanol and gasoline and could cause serious engine failures. Since the MMI sensor is straightforward to fabricate and does not require any special coating it is a cost effective solution for real time and in-situ monitoring of the quality of gasohol blends. PMID:25256111

Numerical analysis of a 3D optical sensor based on single mode fiber to multimode interference graphene design

NASA Astrophysics Data System (ADS)

Mutter, Kussay N.; Jafri, Zubir M.; Tan, Kok Chooi

2016-04-01

In this paper, the simulation and design of a waveguide for water turbidity sensing are presented. The structure of the proposed sensor uses a 2x2 array of multimode interference (MMI) coupler based on micro graphene waveguide for high sensitivity. The beam propagation method (BPM) are used to efficiently design the sensor structure. The structure is consist of an array of two by two elements of sensors. Each element has three sections of single mode for field input tapered to MMI as the main core sensor without cladding which is graphene based material, and then a single mode fiber as an output. In this configuration MMI responses to any change in the environment. We validate and present the results by implementing the design on a set of sucrose solution and showing how these samples lead to a sensitivity change in the sensor based on the MMI structures. Overall results, the 3D design has a feasible and effective sensing by drawing topographical distribution of suspended particles in the water.

Measurement of curvature and temperature using multimode interference devices

NASA Astrophysics Data System (ADS)

Guzman-Sepulveda, J. R.; Aguilar-Soto, J. G.; Torres-Cisneros, M.; Ibarra-Manzano, O. G.; May-Arrioja, D. A.

2011-09-01

In this paper we propose the fabrication, implementation, and testing of a novel fiber optic sensor based on Multimode Interference (MMI) effects for independent measurement of curvature and temperature. The development of fiber based MMI devices is relatively new and since they exhibit a band-pass filter response they can be used in different applications. The operating mechanism of our sensor is based on the self-imaging phenomena that occur in multimode fibers (MMF), which is related to the interference of the propagating modes and their accumulated phase. We demonstrate that the peak wavelength shifts with temperature variations as a result of changes in the accumulated phase through thermo-optics effects, while the intensity of the peak wavelength is reduced as the curvature increases since we start to loss higher order modes. In this way both measurements are obtained independently with a single fiber device. Compared to other fiber-optic sensors, our sensor features an extremely simple structure and fabrication process, and hence cost effectiveness.

All-fiber tunable MMI fiber laser

NASA Astrophysics Data System (ADS)

Antonio-Lopez, J. E.; Castillo-Guzman, A.; May-Arrioja, D. A.; Selvas-Aguilar, R.; LiKamWa, P.

2009-05-01

We report on a novel tuning mechanism to fabricate an all-fiber tunable laser based on multimode interference (MMI) effects. It is well known that the wavelength response of MMI devices exhibits a linear dependence when the length of the multimode fiber (MMF) section. Therefore, tuning in the MMI filter is achieved using a ferrule (capillary tube of 127 μm diameter) filled with a liquid with a higher refractive index than that of the ferrule, which creates a variable liquid MMF. This liquid MMF is used to increase the effective length of the MMI filter and tuning takes place. Using this simple scheme, a tuning range of 30 nm was easily achieved, with very small insertion losses. The filter was tested within a typical Erbium doped fiber (EDF) ring laser cavity, and a tunable EDF laser covering the full C-band was demonstrated. The advantage of our laser is of course the simplicity of the tunable MMI filter, which results in an inexpensive tunable fiber laser.

Silicon-on-insulator multimode-interference waveguide-based arrayed optical tweezers (SMART) for two-dimensional microparticle trapping and manipulation.

PubMed

Lei, Ting; Poon, Andrew W

2013-01-28

We demonstrate two-dimensional optical trapping and manipulation of 1 μm and 2.2 μm polystyrene particles in an 18 μm-thick fluidic cell at a wavelength of 1565 nm using the recently proposed Silicon-on-insulator Multimode-interference (MMI) waveguide-based ARrayed optical Tweezers (SMART) technique. The key component is a 100 μm square-core silicon waveguide with mm length. By tuning the fiber-coupling position at the MMI waveguide input facet, we demonstrate various patterns of arrayed optical tweezers that enable optical trapping and manipulation of particles. We numerically simulate the physical mechanisms involved in the arrayed trap, including the optical force, the heat transfer and the thermal-induced microfluidic flow.

Simultaneous measurement of temperature and magnetic field based on a long period grating concatenated with multimode fiber

NASA Astrophysics Data System (ADS)

Miao, Yinping; Zhang, Hao; Lin, Jichao; Song, Binbin; Zhang, Kailiang; Lin, Wei; Liu, Bo; Yao, Jianquan

2015-03-01

A dual-parameter measurement scheme based on a long-period fiber grating (LPFG) concatenated with a multimode fiber (MMF) has been proposed and experimentally demonstrated for simultaneous measurement of magnetic field and temperature. Splicing the LPFG with the etched MMF enables the coupling between the core modes and different cladding modes of the LPFG as well as the interferences between higher-order modes in the MMF. Due to different transmission mechanisms of the LPFG and mode interference, the proposed sensor shows transmission dip wavelength sensitivities of 0.02878 nm/Oe and -0.04048 nm/°C for multi-mode interference (MMI) and -0.0024 nm/Oe and 0.03929 nm/°C for the LPFG, respectively. By monitoring the opposite behaviors of resonance wavelength shift corresponding to the LPFG and MMI, the magnetic field and environmental temperature can be simultaneously measured. The spectral characteristics of the proposed sensor that could be tuned through control of both environmental temperature and applied magnetic field, which would provide a promising candidate for dual-channel filtering applications as well as multi-parameter measurement applications.

Dual-wavelength noise-like pulse generation in passively mode-locked all-fiber laser based on MMI effect

NASA Astrophysics Data System (ADS)

Shi, Guannan; Fu, Shijie; Sheng, Quan; Shi, Wei; Yao, Jianquan

2018-02-01

We report on the generation of dual-wavelength noise-like pulse (NLP) from a passively mode-locked all-fiber laser based on multimode interference (MMI) effect. The theory to evaluate and design transmission spectrum of MMI filter is analyzed. A homemade MMI filter was employed in an Er-doped fiber ring laser with NPE configuration and dual-wavelength NLP at 1530 and 1600 nm was obtained with 3-dB bandwidth of 18.1 and 41.9 nm, respectively. The output had a signal-to-noise ratio higher than 35 dB and can achieve self-started operation.

An optical mm-wave generation scheme by frequency octupling using a nested MMI

NASA Astrophysics Data System (ADS)

Shang, Lei; Wen, Aijun; Li, Bo; Wang, Tonggang; Chen, Yang; Li, Ming'an

2011-12-01

A novel method of a filterless optical millimeter-wave (MMW) signal generation with frequency octupling via a nested multimode interference (MMI) coupler is proposed for Radio-over-fiber systems. By setting the DC bias voltage applied to the central arms of MMI-b and MMI-c accurately, the optical carrier can be completely suppressed. The OSSR can be as high as about 58 dB without optical filter and the radio frequency spurious suppression ratio (RFSSR) exceeds 32 dB, which is the best result as we know. Simulation results suggest that when the generated optical mm-wave signal is transmitted along the standard single-mode fiber, the eye diagram is still opened after being transmitted over a 50 km fiber.

Long-wave infrared 1 × 2 MMI based on air-gap beneath silicon rib waveguides

NASA Astrophysics Data System (ADS)

Wei, Yuxin; Li, Guoyi; Hao, Yinlei; Li, Yubo; Yang, Jianyi; Wang, Minghua; Jiang, Xiaoqing

2011-08-01

The undercut long-wave infrared (LWIR) waveguide components with air-gap beneath are analyzed and fabricated on the Si-wafer with simple manufacturing process. A 1 × 2 multimode interference (MMI) splitter based on this structure is presented and measured under the 10.6μm wavelength experimental setup. The uniformity of the MMI fabricated is 0.76 dB. The relationship among the output power, slab thickness and air-gap width is also fully discussed. Furthermore, undercut straight waveguides based on SOI platform are fabricated for propagation loss evaluation. Ways to reduce the loss are discussed either.

The Talbot effect in a metamaterial

NASA Astrophysics Data System (ADS)

Nikkhah, H.; Hasan, M.; Hall, T. J.

2018-02-01

The effect of anisotropy and spatial dispersion of a metamaterial on the Talbot effect may be engineered in principle. This has profound implications for applications of the Talbot effect such as the design of a multimode interference coupler (MMI). The paper describes how a metamaterial can suppress the modal phase error which otherwise limits the scaling of MMI port dimension. A binary multilayer dielectric material described by the Kronig-Penney model is shown to provide a close approximation to the required dispersion relation. Results of simulations of a multi-slotted waveguide MMI engineered to provide a polarising beam splitter function are given as an example of the method.

A new design approach to MMI-based (de)multiplexers

NASA Astrophysics Data System (ADS)

Yueyu, Xiao; Sailing, He

2004-09-01

A novel design method of the wavelength (de)multiplexer is presented. The output spectral response of a (de)multiplexer is designed from the view of FIR filters. Avoiding laborious mathematic analysis, the (de)multiplexer is analyzed and designed in this explicit and simple method. A four channel (de)multiplexer based on multimode interference (MMI) is designed as an example. The result obtained agrees with that of the commonly used method, and is verified by a finite difference beam propagation method (FDBPM) simulation.

Theoretical analysis and modeling of a photonic integrated circuit for frequency 8-tupled and 24-tupled millimeter wave signal generation.

PubMed

Hasan, Mehedi; Guemri, Rabiaa; Maldonado-Basilio, Ramón; Lucarz, Frédéric; de Bougrenet de la Tocnaye, Jean-Louis; Hall, Trevor

2014-12-15

A photonic circuit design for implementing frequency 8-tupling and 24-tupling is proposed. The front- and back-end of the circuit comprises 4×4 MMI couplers enclosing an array of four pairs of phase modulators and 2×2 MMI couplers. The proposed design for frequency multiplication requires no optical or electrical filters, the operation is not limited to carefully adjusted modulation indexes, and the drift originated from static DC bias is mitigated by making use of the intrinsic phase relations of multi-mode interference couplers. A transfer matrix approach is used to represent the main building blocks of the design and hence to describe the operation of the frequency 8-tupling and 24-tupling. The concept is theoretically developed and demonstrated by simulations. Ideal and imperfect power imbalances in the multi-mode interference couplers, as well as ideal and imperfect phases of the electric drives to the phase modulators, are analyzed.

The modeling of MMI structures for signal processing applications

NASA Astrophysics Data System (ADS)

Le, Thanh Trung; Cahill, Laurence W.

2008-02-01

Microring resonators are promising candidates for photonic signal processing applications. However, almost all resonators that have been reported so far use directional couplers or 2×2 multimode interference (MMI) couplers as the coupling element between the ring and the bus waveguides. In this paper, instead of using 2×2 couplers, novel structures for microring resonators based on 3×3 MMI couplers are proposed. The characteristics of the device are derived using the modal propagation method. The device parameters are optimized by using numerical methods. Optical switches and filters using Silicon on Insulator (SOI) then have been designed and analyzed. This device can become a new basic component for further applications in optical signal processing. The paper concludes with some further examples of photonic signal processing circuits based on MMI couplers.

Tunable dual-wavelength fiber laser based on an MMI filter in a cascaded Sagnac loop interferometer

NASA Astrophysics Data System (ADS)

Ma, Lin; Kang, Zexin; Qi, Yanhui; Jian, Shuisheng

2014-04-01

A widely tunable dual-wavelength erbium-doped fiber laser based on a cascaded Sagnac loop interferometer incorporating a multimode interference filter is proposed and experimentally demonstrated in this paper. The mode selection is implemented by using the cascaded Sagnac loop interferometer with two segments of polarization maintaining fibers, and the wavelength tuning was achieved by using the refractive index characteristic of multimode interference effects. The tunable dual-wavelength fiber laser has a wavelength tuning of about 40 nm with a signal-to-noise ratio of more than 50 dB.

An on-chip silicon compact triplexer based on cascaded tilted multimode interference couplers

NASA Astrophysics Data System (ADS)

Chen, Jingye; Liu, Penghao; Shi, Yaocheng

2018-03-01

An on-chip triplexer based on cascaded tilted multimode interference (MMI) couplers has been demonstrated to separate the 1310 nm wavelength band into one port and 1490 nm and 1550 nm wavelength bands into the other two ports respectively. By utilizing the dispersive self-imaging and pseudo self-imaging, the device length is not critically determined by the common multiple of beat lengths for different wavelengths. The total device size can be reduced to ∼450 μm, which is half of the butterfly structure reported. The whole device, fabricated with only one fully-etching step, is characterized with <-15 dB low crosstalk (CT) and ∼1 dB insertion loss (IL).

A Photonic 1 × 4 Power Splitter Based on Multimode Interference in Silicon-Gallium-Nitride Slot Waveguide Structures.

PubMed

Malka, Dror; Danan, Yossef; Ramon, Yehonatan; Zalevsky, Zeev

2016-06-25

In this paper, a design for a 1 × 4 optical power splitter based on the multimode interference (MMI) coupler in a silicon (Si)-gallium nitride (GaN) slot waveguide structure is presented-to our knowledge, for the first time. Si and GaN were found as suitable materials for the slot waveguide structure. Numerical optimizations were carried out on the device parameters using the full vectorial-beam propagation method (FV-BPM). Simulation results show that the proposed device can be useful to divide optical signal energy uniformly in the C-band range (1530-1565 nm) into four output ports with low insertion losses (0.07 dB).

Proposal for fabrication-tolerant SOI polarization splitter-rotator based on cascaded MMI couplers and an assisted bi-level taper

PubMed Central

Wang, Jing; Qi, Minghao; Xuan, Yi; Huang, Haiyang; Li, You; Li, Ming; Chen, Xin; Jia, Qi; Sheng, Zhen; Wu, Aimin; Li, Wei; Wang, Xi; Zou, Shichang; Gan, Fuwan

2014-01-01

A novel silicon-on-insulator (SOI) polarization splitter-rotator (PSR) with a large fabrication tolerance is proposed based on cascaded multimode interference (MMI) couplers and an assisted mode-evolution taper. The tapers are designed to adiabatically convert the input TM0 mode into the TE1 mode, which will output as the TE0 mode after processed by the subsequent MMI mode converter, 90-degree phase shifter (PS) and MMI 3 dB coupler. The numerical simulation results show that the proposed device has a < 0.5 dB insertion loss with < −17 dB crosstalk in C optical communication band. Fabrication tolerance analysis is also performed with respect to the deviations of MMI coupler width, PS width, slab height and upper-cladding refractive index, showing that this device could work well even when affected by considerable fabrication errors. With such a robust performance with a large bandwidth, this device offers potential applications for CMOS-compatible polarization diversity, especially in the booming 100 Gb/s coherent optical communications based on silicon photonics technology. PMID:25402029

Proposal for fabrication-tolerant SOI polarization splitter-rotator based on cascaded MMI couplers and an assisted bi-level taper.

PubMed

Wang, Jing; Qi, Minghao; Xuan, Yi; Huang, Haiyang; Li, You; Li, Ming; Chen, Xin; Jia, Qi; Sheng, Zhen; Wu, Aimin; Li, Wei; Wang, Xi; Zou, Shichang; Gan, Fuwan

2014-11-17

A novel silicon-on-insulator (SOI) polarization splitter-rotator (PSR) with a large fabrication tolerance is proposed based on cascaded multimode interference (MMI) couplers and an assisted mode-evolution taper. The tapers are designed to adiabatically convert the input TM(0) mode into the TE(1) mode, which will output as the TE(0) mode after processed by the subsequent MMI mode converter, 90-degree phase shifter (PS) and MMI 3 dB coupler. The numerical simulation results show that the proposed device has a < 0.5 dB insertion loss with < -17 dB crosstalk in C optical communication band. Fabrication tolerance analysis is also performed with respect to the deviations of MMI coupler width, PS width, slab height and upper-cladding refractive index, showing that this device could work well even when affected by considerable fabrication errors. With such a robust performance with a large bandwidth, this device offers potential applications for CMOS-compatible polarization diversity, especially in the booming 100 Gb/s coherent optical communications based on silicon photonics technology.

A simple integrated ratiometric wavelength monitor based on multimode interference structure

NASA Astrophysics Data System (ADS)

Hatta, Agus Muhamad; Farrell, Gerald; Wang, Qian

2008-09-01

Wavelength measurement or monitoring can be implemented using a ratiometric power measurement technique. A ratiometric wavelength monitor normally consists of a Y-branch splitter with two arms: an edge filter arm with a well defined spectral response and a reference arm or alternatively, two edge filters arms with opposite slope spectral responses. In this paper, a simple configuration for an integrated ratiometric wavelength monitor based on a single multimode interference structure is proposed. By optimizing the length of the MMI and the two output port positions, opposite spectral responses for the two output ports can be achieved. The designed structure demonstrates a spectral response suitable for wavelength measurement with potentially a 10 pm resolution over a 100 nm wavelength range.

Two-channel highly sensitive sensors based on 4 × 4 multimode interference couplers

NASA Astrophysics Data System (ADS)

Le, Trung-Thanh

2017-12-01

We propose a new kind of microring resonators (MRR) based on 4 × 4 multimode interference (MMI) couplers for multichannel and highly sensitive chemical and biological sensors. The proposed sensor structure has advantages of compactness and high sensitivity compared with the reported sensing structures. By using the transfer matrix method (TMM) and numerical simulations, the designs of the sensor based on silicon waveguides are optimized and demonstrated in detail. We apply our structure to detect glucose and ethanol concentrations simultaneously. A high sensitivity of 9000 nm/RIU, detection limit of 2 × 10‒4 for glucose sensing and sensitivity of 6000 nm/RIU, detection limit of 1.3 × 10‒5 for ethanol sensing are achieved.

A Photonic 1 × 4 Power Splitter Based on Multimode Interference in Silicon–Gallium-Nitride Slot Waveguide Structures

PubMed Central

Malka, Dror; Danan, Yossef; Ramon, Yehonatan; Zalevsky, Zeev

2016-01-01

In this paper, a design for a 1 × 4 optical power splitter based on the multimode interference (MMI) coupler in a silicon (Si)–gallium nitride (GaN) slot waveguide structure is presented—to our knowledge, for the first time. Si and GaN were found as suitable materials for the slot waveguide structure. Numerical optimizations were carried out on the device parameters using the full vectorial-beam propagation method (FV-BPM). Simulation results show that the proposed device can be useful to divide optical signal energy uniformly in the C-band range (1530–1565 nm) into four output ports with low insertion losses (0.07 dB). PMID:28773638

Demonstration of an optical phased array using electro-optic polymer phase shifters

NASA Astrophysics Data System (ADS)

Hirano, Yoshikuni; Motoyama, Yasushi; Tanaka, Katsu; Machida, Kenji; Yamada, Toshiki; Otomo, Akira; Kikuchi, Hiroshi

2018-03-01

We have been investigating an optical phased array (OPA) using electro-optic (EO) polymers in phase shifters to achieve ultrafast optical beam steering. In this paper, we describe the basic structures of the OPA using EO polymer phase shifters and show the beam steering capability of the OPA. The designed OPA has a multimode interference (MMI) beam splitter and 8-channel polymer waveguides with EO polymer phase shifters. We compare 1 × 8 MMI and cascaded 1 × 2 MMI beam splitters numerically and experimentally, and then obtain uniform intensity outputs from the 1 × 8 beam splitter. We fabricate the EO polymer OPA with a 1 × 8 MMI beam splitter to prevent intensity dispersion due to radiation loss in bending waveguides. We also evaluate the optical beam steering capability of the fabricated OPA and found a 2.7° deflection of far-field patterns when applying a voltage difference of 25 V in adjacent phase shifters.

Ultra-short silicon MMI duplexer

NASA Astrophysics Data System (ADS)

Yi, Huaxiang; Huang, Yawen; Wang, Xingjun; Zhou, Zhiping

2012-11-01

The fiber-to-the-home (FTTH) systems are growing fast these days, where two different wavelengths are used for upstream and downstream traffic, typically 1310nm and 1490nm. The duplexers are the key elements to separate these wavelengths into different path in central offices (CO) and optical network unit (ONU) in passive optical network (PON). Multimode interference (MMI) has some benefits to be a duplexer including large fabrication tolerance, low-temperature dependence, and low-polarization dependence, but its size is too large to integrate in conventional case. Based on the silicon photonics platform, ultra-short silicon MMI duplexer was demonstrated to separate the 1310nm and 1490nm lights. By studying the theory of self-image phenomena in MMI, the first order images are adopted in order to keep the device short. A cascaded MMI structure was investigated to implement the wavelength splitting, where both the light of 1310nm and 1490nm was input from the same port, and the 1490nm light was coupling cross the first MMI and output at the cross-port in the device while the 1310nm light was coupling through the first and second MMI and output at the bar-port in the device. The experiment was carried on with the SOI wafer of 340nm top silicon. The cascaded MMI was investigated to fold the length of the duplexer as short as 117μm with the extinct ratio over 10dB.

Design issues for directional coupler- and MMI-based optical microring resonator filters on InP

NASA Astrophysics Data System (ADS)

Themistos, Christos; Kalli, Kyriacos; Komodromos, Michalis; Rajarajan, Muttukrishnan; Rahman, B. M. A.; Grattan, Kenneth T. V.

2004-08-01

The characterization and optimization of optical microring resonator-based optical filters on deeply etched GaInAsP-Inp waveguides, using the finite element-based beam propagation approach is presented here. Design issues for directional coupler- and multimode interference coupler-based devices, such as field evolution, optical power, phase, fabrication tolerance and wavelength dependence have been investigated.

Micro ring cavity resonator incorporating total internal reflection mirrors

NASA Astrophysics Data System (ADS)

Kim, Doo Gun; Choi, Woon Kyung; Choi, Young Wan; Yi, Jong Chang; Chung, Youngchul; Dagli, Nadir

2007-02-01

We investigate the properties of a multimode-interference (MMI) coupled micro ring cavity resonator with total-internal-reflection (TIR) mirrors and a semiconductor optical amplifier (SOA). The TIR mirrors were fabricated by the self-aligned process with a loss of 0.7 dB per mirror. The length and width of an MMI are 142 μm and 10 μm, respectively. The resulting free spectral range (FSR) of the resonator was approximately 1.698 nm near 1571 nm and the extinction ratio was about 17 dB. These devices might be useful as optical switching and add-drop filters in a photonic integrated circuit or as small and fast resonator devices.

Design optimization of integrated BiDi triplexer optical filter based on planar lightwave circuit.

PubMed

Xu, Chenglin; Hong, Xiaobin; Huang, Wei-Ping

2006-05-29

Design optimization of a novel integrated bi-directional (BiDi) triplexer filter based on planar lightwave circuit (PLC) for fiber-to-the premise (FTTP) applications is described. A multi-mode interference (MMI) device is used to filter the up-stream 1310nm signal from the down-stream 1490nm and 1555nm signals. An array waveguide grating (AWG) device performs the dense WDM function by further separating the two down-stream signals. The MMI and AWG are built on the same substrate with monolithic integration. The design is validated by simulation, which shows excellent performance in terms of filter spectral characteristics (e.g., bandwidth, cross-talk, etc.) as well as insertion loss.

Design optimization of integrated BiDi triplexer optical filter based on planar lightwave circuit

NASA Astrophysics Data System (ADS)

Xu, Chenglin; Hong, Xiaobin; Huang, Wei-Ping

2006-05-01

Design optimization of a novel integrated bi-directional (BiDi) triplexer filter based on planar lightwave circuit (PLC) for fiber-to-the premise (FTTP) applications is described. A multi-mode interference (MMI) device is used to filter the up-stream 1310nm signal from the down-stream 1490nm and 1555nm signals. An array waveguide grating (AWG) device performs the dense WDM function by further separating the two down-stream signals. The MMI and AWG are built on the same substrate with monolithic integration. The design is validated by simulation, which shows excellent performance in terms of filter spectral characteristics (e.g., bandwidth, cross-talk, etc.) as well as insertion loss.

Slot silicon-gallium nitride waveguide in MMI structures based 1x8 wavelength demultiplexer

NASA Astrophysics Data System (ADS)

Ben Zaken, Bar Baruch; Zanzury, Tal; Malka, Dror

2017-06-01

We propose a novel 8-channel wavelength multimode interference (MMI) demultiplexer in slot waveguide structures that operated at 1530 nm, 1535 nm, 1540 nm, 1545 nm, 1550 nm, 1555 nm, 1560 nm and 1565 nm wavelengths. Gallium nitride (GaN) surrounded by silicon (Si) was founded as suitable materials for the slot-waveguide structures. The proposed device was designed by seven 1x2 MMI couplers, fourteen S-band and one input taper. Numerical investigations were carried out on the geometrical parameters by using a full vectorial-beam propagation method (FVBPM). Simulation results show that the proposed device can transmit 8-channel that works in the whole C-band (1530- 1565 nm) with low crosstalk ((-19.97)-(-13.77) dB) and bandwidth (1.8-3.6 nm). Thus, the device can be very useful in optical networking systems that work on dense wavelength division multiplexing (DWDM) technology.

Design and analysis of O-S-C triple band wavelength division demultiplexer using cascaded MMI couplers

NASA Astrophysics Data System (ADS)

Chack, Devendra; Kumar, V.; Raghuwanshi, Sanjeev Kumar; Singh, Dev Prakash

2017-01-01

Compact triple O-S-C band wavelength demultiplexer, which consists of series cascaded multimode interference (MMI) couplers has been carried out in this paper. The MMI coupler has been used to drop the wavelengths of 1510 nm and 1550 nm at bar port while the wavelength 1300 nm into the cross port. Then another MMI coupler has been designed to separate the wavelength 1510 nminto one port and wavelength 1550 nm into another port. The triple wavelength demultiplexer function has been performed by choosing a suitable refractive index of the guiding region and geometrical parameters such as the width and length of MMI coupler. Numerical simulation with finite difference beam propagation method (BPM) has been utilized to design and optimize the operation of the proposed triple wavelength demultiplexer. The simulation results show that insertion losses of wavelength O, S and C, bands are 1.884 dB, 1.452 dB and 2.568 dB, respectively, with isolations for each output waveguide ranging from 10 dB to 28.72 dB. The 3-dB bandwidth of insertion loss for 1300 nm, 1510 nm and 1550 nm are 80 nm, 20 nm and 10 nm, respectively.

Two kinds of novel tunable Thulium-doped fiber laser

NASA Astrophysics Data System (ADS)

Ma, Xiaowei; Chen, Daru; Feng, Gaofeng; Yang, Junyong

2014-11-01

Two kinds of tunable Thulium-doped fiber laser (TDFL) respectively using a Sagnac loop mirror and a novel tunable multimode interference (MMI) fiber filter are experimentally demonstrated. The TDFL with the Sagnac loop mirror made by a 145.5-cm polarization-maintaining fiber (PMF) can operate with stable dual-wavelength lasing or tunable single-wavelength lasing around 1860nm. Both stable dual-wavelength and tunable single-wavelength lasing are achieved by adjusting a polarization controller in the Sagnac loop mirror. The TDFL with a novel tunable MMI fiber filter formed by splicing a segment of a special no-core fiber that is an all silica fiber without fiber core to single mode fibers can achieve tuning range from 1813.52 nm to 1858.70 nm. The no-core fiber with a large diameter of 200 μm is gradually vertically covered by refractive index matching liquid, which leads to a wavelength tuning of the transmission peak of the MMI fiber filter. The relationship between the refractive index of the refractive index matching liquid and the peak wavelength shift of the MMI fiber filter is also discussed. Using the MMI fiber filter, a Thulium-doped fiber laser with a tuning range of 45.18 nm is demonstrated.

Realization of an ultra-compact polarization beam splitter using asymmetric MMI based on silicon nitride / silicon-on-insulator platform.

PubMed

Sun, Xiao; Aitchison, J Stewart; Mojahedi, Mo

2017-04-03

We have experimentally demonstrated a compact polarization beam splitter (PBS) based on the silicon nitride/silicon-on-insulator platform using the recently proposed augmented-low-index-guiding (ALIG) waveguide structure. The two orthogonal polarizations are split in an asymmetric multimode interference (MMI) section, which was 1.6 μm wide and 4.8 μm long. The device works well over the entire C-band wavelength range and has a measured low insertion loss of less than 1 dB. The polarization extinction ratio at the Bar Port is approximately 17 dB and at the Cross Port is approximately 25 dB. The design of the device is robust and has a good fabrication tolerance.

Highly Sensitive Liquid Core Temperature Sensor Based on Multimode Interference Effects

PubMed Central

Fuentes-Fuentes, Miguel A.; May-Arrioja, Daniel A.; Guzman-Sepulveda, José R.; Torres-Cisneros, Miguel; Sánchez-Mondragón, José J.

2015-01-01

A novel fiber optic temperature sensor based on a liquid-core multimode interference device is demonstrated. The advantage of such structure is that the thermo-optic coefficient (TOC) of the liquid is at least one order of magnitude larger than that of silica and this, combined with the fact that the TOC of silica and the liquid have opposite signs, provides a liquid-core multimode fiber (MMF) highly sensitive to temperature. Since the refractive index of the liquid can be easily modified, this allows us to control the modal properties of the liquid-core MMF at will and the sensor sensitivity can be easily tuned by selecting the refractive index of the liquid in the core of the device. The maximum sensitivity measured in our experiments is 20 nm/°C in the low-temperature regime up to 60 °C. To the best of our knowledge, to date, this is the largest sensitivity reported for fiber-based MMI temperature sensors. PMID:26512664

Waveguide couplers with new power splitting ratios made possible by cascading of short multimode interference sections

NASA Astrophysics Data System (ADS)

Feng, David J. Y.; Lay, T. S.; Chang, T. Y.

2007-02-01

We show that it is possible to obtain 2 x 2 waveguide couplers with new power splitting ratios for cross coupling of 7%, 64%, 80% and 93% by cascading two short MMI sections. These couplers have simple geometry and low loss. They offer valuable new possibilities for designing waveguide power taps, high-Q ring resonators, ladder-structure optical filters, and loop-mirror partial reflectors.

Bi-directional triplexer with butterfly MMI coupler using SU-8 polymer waveguides

NASA Astrophysics Data System (ADS)

Mareš, David; Jeřábek, Vítězslav; Prajzler, Václav

2015-01-01

We report about a design of a bi-directional planar optical multiplex/demultiplex filter (triplexer) for the optical part of planar hybrid WDM bi-directional transceiver in fiber-to-the-home (FTTH) PON applications. The triplex lightwave circuit is based on the Epoxy Novolak Resin SU-8 waveguides on the silica-on-silicon substrate with Polymethylmethacrylate cladding layer. The triplexer is comprised of a linear butterfly concept of multimode interference (MMI) coupler separating downstream optical signals of 1490 nm and 1550 nm. For the upstream channel of 1310 nm, an additional directional coupler (DC) is used to add optical signal of 1310 nm propagating in opposite direction. The optical triplexer was designed and optimized using beam propagation method. The insertion losses, crosstalk attenuation, and extinction ratio for all three inputs/outputs were investigated. The intended triplexer was designed using the parameters of the separated DC and MMI filter to approximate the idealized direct connection of both devices.

Refractive-index-sensing fiber comb using intracavity multi-mode interference fiber sensor

NASA Astrophysics Data System (ADS)

Oe, Ryo; Minamikawa, Takeo; Taue, Shuji; Fukano, Hideki; Nakajima, Yoshiaki; Minoshima, Kaoru; Yasui, Takeshi

2018-02-01

Refractive index measurement is important for evaluation of liquid materials, optical components, and bio sensing. One promising approach for such measurement is use of optical fiber sensors such as surface plasmonic resonance or multi-mode interference (MMI), which measure the change of optical spectrum resulting from the refractive index change. However, the precision of refractive index measurement is limited by the performance of optical spectrum analyzer. If such the refractive index measurement can be performed in radio frequency (RF) region in place of optical region, the measurement precision will be further improved by the frequency-standard-based RF measurement. To this end, we focus on the disturbance-to-RF conversion in a fiber optical frequency comb (OFC) cavity. Since frequency spacing frep of OFC depends on an optical cavity length nL, frep sensitively reflects the external disturbance interacted with nL. Although we previously demonstrated the precise strain measurement based on the frep measurement, the measurable physical quantity is limited to strain or temperature, which directly interacts with the fiber cavity itself. If a functional fiber sensor can be installed into the fiber OFC cavity, the measurable physical quantity will be largely expanded. In this paper, we introduce a MMI fiber sensor into a ring-type fiber OFC cavity for refractive index measurement. We confirmed the refractive-index-dependent frep shift.

Spectrally reconfigurable integrated multi-spot particle trap.

PubMed

Leake, Kaelyn D; Olson, Michael A B; Ozcelik, Damla; Hawkins, Aaron R; Schmidt, Holger

2015-12-01

Optical manipulation of small particles in the form of trapping, pushing, or sorting has developed into a vast field with applications in the life sciences, biophysics, and atomic physics. Recently, there has been increasing effort toward integration of particle manipulation techniques with integrated photonic structures on self-contained optofluidic chips. Here, we use the wavelength dependence of multi-spot pattern formation in multimode interference (MMI) waveguides to create a new type of reconfigurable, integrated optical particle trap. Interfering lateral MMI modes create multiple trapping spots in an intersecting fluidic channel. The number of trapping spots can be dynamically controlled by altering the trapping wavelength. This novel, spectral reconfigurability is utilized to deterministically move single and multiple particles between different trapping locations along the channel. This fully integrated multi-particle trap can form the basis of high throughput biophotonic assays on a chip.

Liquid level and temperature sensing by using dual-wavelength fiber laser based on multimode interferometer and FBG in parallel

NASA Astrophysics Data System (ADS)

Sun, Chunran; Dong, Yue; Wang, Muguang; Jian, Shuisheng

2018-03-01

The detection of liquid level and temperature based on a fiber ring cavity laser sensing configuration is presented and demonstrated experimentally. The sensing head contains a fiber Bragg grating (FBG) and a single-mode-cladding-less-single-mode multimode interferometer, which also functions as wavelength-selective components of the fiber laser. When the liquid level or temperature is applied on the sensing head, the pass-band peaks of both multimode interference (MMI) filter and FBG filter vary and the two output wavelengths of the laser shift correspondingly. In the experiment, the corresponding sensitivities of the liquid level with four different refractive indices (RI) in the deep range from 0 mm to 40 mm are obtained and the sensitivity enhances with the RI of the liquid being measured. The maximum sensitivity of interferometer is 106.3 pm/mm with the RI of 1.391. For the temperature measurement, a sensitivity of 10.3 pm/°C and 13.8 pm/°C are achieved with the temperature ranging from 0 °C to 90 °C corresponding to the two lasing wavelengths selective by the MMI filter and FBG, respectively. In addition, the average RI sensitivity of 155.77 pm/mm/RIU is also obtained in the RI range of 1.333-1.391.

Stabilized and tunable single-longitudinal-mode erbium fiber laser employing ytterbium-doped fiber based interference filter

NASA Astrophysics Data System (ADS)

Yeh, Chien-Hung; Tsai, Ning; Zhuang, Yuan-Hong; Chow, Chi-Wai; Chen, Jing-Heng

2017-02-01

In this demonstration, to achieve stabilized and wavelength-selectable single-longitudinal-mode (SLM) erbium-doped fiber (EDF) laser, a short length of ytterbium-doped fiber (YDF) is utilized to serve as a spatial multi-mode interference (MMI) inside a fiber cavity for suppressing multi-longitudinal-mode (MLM) significantly. In the measurement, the output powers and optical signal to noise ratios (OSNRs) of proposed EDF ring laser are measured between -9.85 and -5.71 dBm; and 38.03 and 47.95 dB, respectively, in the tuning range of 1530.0-1560.0 nm. In addition, the output SLM and stability performance are also analyzed and discussed experimentally.

Fabrication of 8×8 MMI optical coupler in BK7 by ion-exchange

NASA Astrophysics Data System (ADS)

Li, Xia; Li, Xi-Hua; Zhou, Qiang; Jiang, Xiao-Qing; Yang, Jian-Yi; Wang, Ming-Hua

2005-01-01

The planar waveguide optical couplers are of prime importance in optical communication and optical signal processing system. Comparing with the optical fiber coupler (OFC) which fabricated by fused biconical taper technology, the planar waveguide couplers are more compact size, lower loss, better uniformity, easier manufacture and integration. Multimode interference (MMI) couplers have many advantages, such as compact size, wavelength and polarization insensitivity, fabrication tolerances and low loss, etc., which concentrate more and more attention. Conventional MMI devices are based on the uniform index waveguides. When the number of input/output waveguides becomes larger, the intrinsic propagation constant error, which will cause bad uniformity of output power, can"t be neglected. In fact, most waveguide devices are graded-index. With the enhanced compatibility of MMI coupler, the performance can be improved at the same time. Prior study shows that graded-index MMI couplers reach the best performance under certain index contrast. Among many available materials, glass is chosen to be the substrate of the coupler, because of its good features, such as low loss, ease fabrication, cheap cost, and so on. In this paper, an 8×8 MMI optical coupler is designed based on the principle of graded-index MMI. The coupler is composed of a waveguide, which is designed to support a large number of modes, and several access (usually single-mode) waveguides, which are used to launch light into and recover light from that multimode waveguide. The total length of the device is less than 3.5 centimeter, including S-bends which lead the multiple images to the output of the device with the spacing D=250μm to make the device fiber compatible. In this paper, we describe an experimental realization of the 8×8 graded-index MMI optical coupler and the measurement of its performance with the testing laser of the wavelength of 1.55μm. The device is fabricated by ion-exchange on BK7 glass substrate. During the ion-exchange process, a melting mixture of AgNO3 : (KNO3 : NaNO3) (molar ratio, 0.001:1) is used at 350~380°C for different times (range from 8 to 18 hours) to fabricate the coupler. The experimental results show that the performance of the optical coupler is quite promising. For instance, while launching light from No.5 waveguide, the uniformity of the device is approximately 0.72dB. Optimization of design and fabrication is going on to improve the total performance of the optical coupler.

Widely tunable semiconductor lasers with three interferometric arms.

PubMed

Su, Guan-Lin; Wu, Ming C

2017-09-04

We present a comprehensive study for a new three-branch widely tunable semiconductor laser based on a self-imaging, lossless multi-mode interference (MMI) coupler. We have developed a general theoretical framework that is applicable to all types of interferometric lasers. Our analysis showed that the three-branch laser offers high side-mode suppression ratios (SMSRs) while maintaining a wide tuning range and a low threshold modal gain of the lasing mode. We also present the design rules for tuning over the dense-wavelength division multiplexing grid over the C-band.

InP-based compact transversal filter for monolithically integrated light source array.

PubMed

Ueda, Yuta; Fujisawa, Takeshi; Takahata, Kiyoto; Kohtoku, Masaki; Ishii, Hiroyuki

2014-04-07

We developed an InP-based 4x1 transversal filter (TF) with multi-mode interference couplers (MMIs) as a compact wavelength multiplexer (MUX) 1700 μm x 400 μm in size. Furthermore, we converted the MMI-based TF to a reflection type to obtain an ultra-compact MUX of only 900 μm x 50 μm. These MUXs are made with a simple fabrication process and show a satisfactory wavelength filtering operation as MUXs of monolithically integrated light source arrays, for example, for 100G bit Ethernet.

Optofluidic wavelength division multiplexing for single-virus detection

PubMed Central

Ozcelik, Damla; Parks, Joshua W.; Wall, Thomas A.; Stott, Matthew A.; Cai, Hong; Parks, Joseph W.; Hawkins, Aaron R.; Schmidt, Holger

2015-01-01

Optical waveguides simultaneously transport light at different colors, forming the basis of fiber-optic telecommunication networks that shuttle data in dozens of spectrally separated channels. Here, we reimagine this wavelength division multiplexing (WDM) paradigm in a novel context––the differentiated detection and identification of single influenza viruses on a chip. We use a single multimode interference (MMI) waveguide to create wavelength-dependent spot patterns across the entire visible spectrum and enable multiplexed single biomolecule detection on an optofluidic chip. Each target is identified by its time-dependent fluorescence signal without the need for spectral demultiplexing upon detection. We demonstrate detection of individual fluorescently labeled virus particles of three influenza A subtypes in two implementations: labeling of each virus using three different colors and two-color combinatorial labeling. By extending combinatorial multiplexing to three or more colors, MMI-based WDM provides the multiplexing power required for differentiated clinical tests and the growing field of personalized medicine. PMID:26438840

Thermo-optic characteristic of DNA thin solid film and its application as a biocompatible optical fiber temperature sensor.

PubMed

Hong, Seongjin; Jung, Woohyun; Nazari, Tavakol; Song, Sanggwon; Kim, Taeoh; Quan, Chai; Oh, Kyunghwan

2017-05-15

We report unique thermo-optical characteristics of DNA-Cetyl tri-methyl ammonium (DNA-CTMA) thin solid film with a large negative thermo-optical coefficient of -3.4×10^-4/°C in the temperature range from 20°C to 70°C without any observable thermal hysteresis. By combining this thermo-optic DNA film and fiber optic multimode interference (MMI) device, we experimentally demonstrated a highly sensitive compact temperature sensor with a large spectral shift of 0.15 nm/°C. The fiber optic MMI device was a concatenated structure with single-mode fiber (SMF)-coreless silica fiber (CSF)-single mode fiber (SMF) and the DNA-CTMA film was deposited on the CSF. The spectral shifts of the device in experiments were compared with the beam propagation method, which showed a good agreement.

Deeply etched MMI-based components on 4 μm thick SOI for SOA-based optical RAM cell circuits

NASA Astrophysics Data System (ADS)

Cherchi, Matteo; Ylinen, Sami; Harjanne, Mikko; Kapulainen, Markku; Aalto, Timo; Kanellos, George T.; Fitsios, Dimitrios; Pleros, Nikos

2013-02-01

We present novel deeply etched functional components, fabricated by multi-step patterning in the frame of our 4 μm thick Silicon on Insulator (SOI) platform based on singlemode rib-waveguides and on the previously developed rib-tostrip converter. These novel components include Multi-Mode Interference (MMI) splitters with any desired splitting ratio, wavelength sensitive 50/50 splitters with pre-filtering capability, multi-stage Mach-Zehnder Interferometer (MZI) filters for suppression of Amplified Spontaneous Emission (ASE), and MMI resonator filters. These novel building blocks enable functionalities otherwise not achievable on our SOI platform, and make it possible to integrate optical RAM cell layouts, by resorting to our technology for hybrid integration of Semiconductor Optical Amplifiers (SOAs). Typical SOA-based RAM cell layouts require generic splitting ratios, which are not readily achievable by a single MMI splitter. We present here a novel solution to this problem, which is very compact and versatile and suits perfectly our technology. Another useful functional element when using SOAs is the pass-band filter to suppress ASE. We pursued two complimentary approaches: a suitable interleaved cascaded MZI filter, based on a novel suitably designed MMI coupler with pre-filtering capabilities, and a completely novel MMI resonator concept, to achieve larger free spectral ranges and narrower pass-band response. Simulation and design principles are presented and compared to preliminary experimental functional results, together with scaling rules and predictions of achievable RAM cell densities. When combined with our newly developed ultra-small light-turning concept, these new components are expected to pave the way for high integration density of RAM cells.

High-speed photodiodes for InP-based photonic integrated circuits.

PubMed

Rouvalis, E; Chtioui, M; Tran, M; Lelarge, F; van Dijk, F; Fice, M J; Renaud, C C; Carpintero, G; Seeds, A J

2012-04-09

We demonstrate the feasibility of monolithic integration of evanescently coupled Uni-Traveling Carrier Photodiodes (UTC-PDs) having a bandwidth exceeding 100 GHz with Multimode Interference (MMI) couplers. This platform is suitable for active-passive, butt-joint monolithic integration with various Multiple Quantum Well (MQW) devices for narrow linewidth millimeter-wave photomixing sources. The fabricated devices achieved a high 3-dB bandwidth of up to 110 GHz and a generated output power of more than 0 dBm (1 mW) at 120 GHz with a flat frequency response over the microwave F-band (90-140 GHz).

Highly integrated optical 8x8 lambda-router in silicon-on-insulator technology: comparison between the ring and racetrack configuration

NASA Astrophysics Data System (ADS)

Fan, G. F.; Orobtchouk, R.; Fédéli, J. M.

2010-05-01

In this paper, we demonstrate a compact 8x8 λ-router using multimode-interference (MMI) crossing based on the microring resonator. The 8x8 λ-router was designed and fabricated with a CMOS compatible silicon on insulator technology. MMI is used to reduce the cross talk and the crossing losses of the device. Microrings with a nominal radius of 2.5 μm and small variations of 10 nm of the nominal value allow respectively a free spectral range of 32 nm and spacing between channels of 4 nm. The experimental results are in good agreement with the modeling. The basic add drop filters of the devices exhibit losses of -2 dB and on/off contrast of the resonance of 20 dB. The total losses for one channel are about -4 dB and the imbalance between the 8 channels is lower than 2 dB.

Realization of a compact polarization splitter-rotator on silicon.

PubMed

Dai, Daoxin; Wu, Hao

2016-05-15

A novel compact polarization splitter-rotator (PSR) is proposed and realized with silicon-on-insulator nanowires. The present PSR consists of an adiabatic taper, an asymmetric directional coupler (ADC), and a multimode interference (MMI) mode filter. The adiabatic taper enables an efficient mode conversion from the launched TM₀ mode to the TE₁ mode in a wide waveguide, which is then coupled to the TE₀ mode of a narrow waveguide through the ADC. Meanwhile, the launched TE₀ mode does not have mode conversion and outputs from the through port directly. The MMI mode filter is cascaded at the through port to filter out the residual power of the TE₁ mode so that the extinction ratio of the PSR is improved greatly. The total length of the PSR is ∼70  μm and the fabricated PSR has an extinction ratio of ∼20  dB over a broadband ranging from 1547 to 1597 nm.

Analysis of a single ring resonator with 2×2 90-degree multimode waveguide turning couplers

NASA Astrophysics Data System (ADS)

Chiu, C. L.; Liao, Yen-Hsun

2016-02-01

A novel design of a single ring resonator with two low-loss 2×2 90-degree multimode waveguide turning mirror couplers based on a InP structure. The coupling factor of the 2×2 90-degree multimode waveguide turning mirror coupler is inversed for K=0.85 to K=0.15 when one folding is achieved. The 2×2 90-degree turning mirror coupler for K=0.15 is (3/4)Lπ in length. Its length is reduced 3 times than the conventional straight 2×2 multimode waveguide interference coupler (9/4)Lπ in length for K=0.15. The cavity length of the curve waveguide (90-degree arc length) in this ring resonator with two 2×2 90-degree multimode waveguide turning couplers is decreased 1/2 times than with two 2×2 MMI couplers (180-degree arc length). The free spectral range (FSR) is increased 2 times. The output spectral response gets a FSR of 82 GHz for the device and a contrast of 4 dB and FWHM of 0.24 nm for the drop port. The results of numerical analysis calculated by the transfer functions in a single ring resonator are agreement with the experimental results.

Optofluidic tuning of multimode interference fiber filters

NASA Astrophysics Data System (ADS)

Antonio-Lopez, J. E.; May-Arrioja, D. A.; LiKamWa, P.

2009-05-01

We report on the optofluidic tuning of MMI-based bandpass filters. It is well known that MMI devices exhibit their highest sensitivity when their diameter (D) is modified, since they have a D2 wavelength dependence. In order to increase the MMF diameter we use a special fiber, called No-Core fiber, which is basically a MMF with a diameter of 125 μm with air as the cover. Therefore, when this No-Core fiber is immersed in liquids with different refractive indexes, as a result of the Goes-Hänchen shift the effective width (fundamental mode width) of the No-Core fiber is increased, and thus the peak wavelength is tuned. A tunability of almost 40 nm in going from air (n=1.333) to ethylene glycol (n=1.434) was easily obtained, with a minimum change in peak transmission, contrast, and bandwidth. Moreover, since replacing the entire liquid can be difficult, the device was placed vertically and the liquid was covering the No-Core fiber in small steps. This provided similar amount of tuning as before, but a more controllable tuning mechanism.

Interferometric imaging using Si3N4 photonic integrated circuits for a SPIDER imager.

PubMed

Su, Tiehui; Liu, Guangyao; Badham, Katherine E; Thurman, Samuel T; Kendrick, Richard L; Duncan, Alan; Wuchenich, Danielle; Ogden, Chad; Chriqui, Guy; Feng, Shaoqi; Chun, Jaeyi; Lai, Weicheng; Yoo, S J B

2018-05-14

This paper reports design, fabrication, and experimental demonstration of a silicon nitride photonic integrated circuit (PIC). The PIC is capable of conducting one-dimensional interferometric imaging with twelve baselines near λ = 1100-1600 nm. The PIC consists of twelve waveguide pairs, each leading to a multi-mode interferometer (MMI) that forms broadband interference fringes or each corresponding pair of the waveguides. Then an 18 channel arrayed waveguide grating (AWG) separates the combined signal into 18 signals of different wavelengths. A total of 103 sets of fringes are collected by the detector array at the output of the PIC. We keep the optical path difference (OPD) of each interferometer baseline to within 1 µm to maximize the visibility of the interference measurement. We also constructed a testbed to utilize the PIC for two-dimension complex visibility measurement with various targets. The experiment shows reconstructed images in good agreement with theoretical predictions.

Compact polarizing beam splitter based on a metal-insulator-metal inserted into multimode interference coupler.

PubMed

Chheang, Vuthy; Lee, Tae-Kyeong; Oh, Geum-Yoon; Kim, Hong-Seung; Lee, Byeong-Hyeon; Kim, Doo Gun; Choi, Young-Wan

2013-09-09

We propose and analyze a compact polarizing beam splitter (PBS) based on a metal-insulator-metal (MIM) structure inserted into a multimode interference coupler (MMI). Owing to the MIM structure, the TE polarized state is reflected by the cut-off condition while the TM polarized state is transmitted by the surface plasmon polariton, and the two polarized states can thus be separated. In this paper, the dependence of the reflected TE and transmitted TM field intensities on the MIM length and the gap thickness has been studied systematically. The proposed PBS structure, with a total size of 4 × 0.7 × 44 µm(3) is designed with MIM length, gap thickness, and metal thickness of 0.6 µm, 0.5 µm, and 0.05 µm, respectively. In the designed PBS, the transmittance for the TM polarized light, reflectance for the TE polarized light, extinction ratio, and insertion losses of the TE and TM modes are obtained using a 3D finite-difference time-domain method to be 0.9, 0.88, 12.55 dB, and 1.1 dB and 0.9 dB, respectively. The designed PBS has a much shorter length, 44 µm, compared to previous PBS devices.

Monolithically integrated distributed feedback laser array wavelength-selectable light sources for WDM-PON application

NASA Astrophysics Data System (ADS)

Chen, Xin; Zhao, Jianyi; Zhou, Ning; Huang, Xiaodong; Cao, Mingde; Wang, Lei; Liu, Wen

2015-01-01

The monolithic integration of 1.5-μm four channels phase shift distributed feedback lasers array (DFB-LD array) with 4×1 multi-mode interference (MMI) optical combiner is demonstrated. A home developed process mainly consists of butt-joint regrowth (BJR) and simultaneous thermal and ultraviolet nanoimprint lithography (STU-NIL) is implemented to fabricate gratings and integrated devices. The threshold currents of the lasers are less than 10 mA and the side mode suppression ratios (SMSR) are better than 40 dB for all channels. Quasi-continuous tuning is realized over 7.5 nm wavelength region with the 30 °C temperature variation. The results indicate that the integration device we proposed can be used in wavelength division multiplexing passive optical networks (WDM-PON).

Low-loss multimode interference couplers for terahertz waves

NASA Astrophysics Data System (ADS)

Themistos, Christos; Kalli, Kyriacos; Komodromos, Michael; Markides, Christos; Quadir, Anita; Rahman, B. M. Azizur; Grattan, Kenneth T. V.

2012-04-01

The terahertz (THz) frequency region of the electromagnetic spectrum is located between the traditional microwave spectrum and the optical frequencies, and offers a significant scientific and technological potential in many fields, such as in sensing, in imaging and in spectroscopy. Waveguiding in this intermediate spectral region is a major challenge. Amongst the various THz waveguides suggested, metal-clad plasmonic waveguides and specifically hollow core structures, coated with insulating material are the most promising low-loss waveguides used in both active and passive devices. Optical power splitters are important components in the design of optoelectronic systems and optical communication networks such as Mach-Zehnder Interferometric switches, polarization splitter and polarization scramblers. Several designs for the implementation of the 3dB power splitters have been proposed in the past, such as the directional coupler-based approach, the Y-junction-based devices and the MMI-based approach. In the present paper a novel MMI-based 3dB THz wave splitter is implemented using Gold/polystyrene (PS) coated hollow glass rectangular waveguides. The H-field FEM based full-vector formulation is used here to calculate the complex propagation characteristics of the waveguide structure and the finite element beam propagation method (FE-BPM) and finite difference time domain (FDTD) approach to demonstrate the performance of the proposed 3dB splitter.

Design of optical metamaterial waveguide structures (Conference Presentation)

NASA Astrophysics Data System (ADS)

Ortega-Moñux, Alejandro; Halir, Robert; Sánchez-Postigo, Alejandro; Soler-Penadés, Jordi; Ctyroký, Jirí; Luque-González, José Manuel; Sarmiento-Merenguel, José Darío.; Wangüemert-Pérez, Juan Gonzalo; Schmid, Jens H.; Xu, Dan-Xia; Janz, Sigfried; Lapointe, Jean; Molina-Fernández, Iñigo; Nedeljkovic, Milos; Mashanovich, Goran Z.; Cheben, Pavel

2017-05-01

Subwavelength gratings (SWGs) are periodic structures with a pitch (Λ) smaller than the wavelength of the propagating wave (λ), so that diffraction effects are suppressed. These structures thus behave as artificial metamaterials where the refractive index and the dispersion profile can be controlled with a proper design of the geometry of the structure. SWG waveguides have found extensive applications in the field of integrated optics, such as efficient fiber-chip couplers, broadband multimode interference (MMI) couplers, polarization beam splitters or evanescent field sensors, among others. From the point of view of nano-fabrication, the subwavelength condition (Λ << λ) is much easier to meet for long, mid-infrared wavelengths than for the comparatively short near-infrared wavelengths. Since most of the integrated devices based on SWGs have been proposed for the near-infrared, the true potential of subwavelength structures has not yet been completely exploited. In this talk we summarize some valuable guidelines for the design of high performance SWG integrated devices. We will start describing some practical aspects of the design, such as the range of application of semi-analytical methods, the rigorous electromagnetic simulation of Floquet modes, the relevance of substrate leakage losses and the effects of the random jitter, inherent to any fabrication process, on the performance of SWG structures. Finally, we will show the possibilities of the design of SWG structures with two different state-of-the-art applications: i) ultra-broadband MMI beam splitters with an operation bandwidth greater than 300nm for telecom wavelengths and ii) a set of suspended waveguides with SWG lateral cladding for mid-infrared applications, including low loss waveguides, MMI couplers and Mach-Zehnder interferometers.

1 × 4 MMI visible light wavelength demultiplexer based on a GaN slot-waveguide structure

NASA Astrophysics Data System (ADS)

Shoresh, Tamir; Katanov, Nadav; Malka, Dror

2018-07-01

High transmission losses are the key problem that limits the performance of visible light communication systems, which work on wavelength division multiplexing (WDM) technology. To overcome this problem, we propose a novel design for a 1 × 4 optical demultiplexer based on the multimode interference in a slot-waveguide structure that operates at 547 nm, 559 nm, 566 nm, and 584 nm. Gallium nitride and silicon oxide were found to be excellent materials for the slot-waveguide structure. Simulation results showed that the proposed device can transmit four channels that work in the visible light range with a low transmission loss of 0.983-1.423 dB, crosstalk of 13.8-18.3 dB, and bandwidth of 1.8-3.2 nm. Thus, this device can be very useful in visible light networking systems, which work on the WDM technology.

Optical interconnects for in-plane high-speed signal distribution at 10 Gb/s: Analysis and demonstration

NASA Astrophysics Data System (ADS)

Chang, Yin-Jung

With decreasing transistor size, increasing chip speed, and larger numbers of processors in a system, the performance of a module/system is being limited by the off-chip and off-module bandwidth-distance products. Optical links have moved from fiber-based long distance communications to the cabinet level of 1m--100m, and recently to the backplane-level (10cm--1m). Board-level inter-chip parallel optical interconnects have been demonstrated recently by researchers from Intel, IBM, Fujitsu, NTT and a few research groups in universities. However, the board-level signal/clock distribution function using optical interconnects, the lightwave circuits, the system design, a practically convenient integration scheme committed to the implementation of a system prototype have not been explored or carefully investigated. In this dissertation, the development of a board-level 1 x 4 optical-to-electrical signal distribution at 10Gb/s is presented. In contrast to other prototypes demonstrating board-level parallel optical interconnects that have been drawing much attention for the past decade, the optical link design for the high-speed signal broadcasting is even more complicated and the pitch between receivers could be varying as opposed to fixed-pitch design that has been widely-used in the parallel optical interconnects. New challenges for the board-level high-speed signal broadcasting include, but are not limited to, a new optical link design, a lightwave circuit as a distribution network, and a novel integration scheme that can be a complete radical departure from the traditional assembly method. One of the key building blocks in the lightwave circuit is the distribution network in which a 1 x 4 multimode interference (MMI) splitter is employed. MMI devices operating at high data rates are important in board-level optical interconnects and need to be characterized in the application of board-level signal broadcasting. To determine the speed limitations of MMI devices, the ultra-short pulse response of these devices is modeled based on the guided-mode theory incorporated with Fourier transform technique. For example, for 50 fs Gaussian input pulses into a 1 x 16 splitter, the output pulses are severely degraded in coupling efficiency (48%) and completely broken up in time primarily due to inter-modal and intra-modal (waveguide) dispersion. Material dispersion is found to play only a minor role in the pulse response of MMI devices. However, for 1ps input pulses into the same 1 x 16 splitter, the output pulses are only moderately degraded in coupling efficiency (86%) and only slightly degraded in shape. With the understanding of the necessary condition of the distortionless high-speed signal transmission through MMI devices, high-speed data transmission at 40Gb/s per channel with a total bandwidth of 320Gb/s for 8 output ports is demonstrated for the first time on a 1 x 8 photo-definable polymer-based MMI power splitter. The device is designed with multimode input/output waveguides of 10mum in width and 7.6mum in height for a better input coupling efficiency for which the high-speed testing demands. The eye diagrams are all clear and fully open with an extinction ratio of 10.1dB and a jitter of 1.65 ps. The transmission validity is further confirmed by the bit-error-rate testing at the pseudoramdom binary sequence of 27--1. The fabrication process developed lays the cornerstone of the integration scheme and system design for the prototype of hybrid interconnects. An important problem regarding the guided-mode attenuation associated with optical-interconnect-polymer waveguides fabricated on FR-4 printed-circuit boards is also quantified for the first time. On-board optical waveguides are receiving more attention recently from Fujitsu American Laboratory, IBM Watson Research Center, and Packaging Research Center here at Georgia Tech. This branch of research work is part of the effort in investigating, scientifically, the attenuation mechanism and the effects of the buffer layer thickness on board-level in-plane optical interconnects. The rigorous transmission-line network approach is used and the FR-4 substrate is treated as a long-period substrate grating. A quantitative metric for an appropriate matrix truncation is presented. The peaks of attenuation are shown to occur near the Bragg conditions that characterize the leaky-wave stop bands. For a typical 400mum period FR-4 substrate with an 8mum corrugation depth, a buffer layer thickness of about 40mum is found to be needed to make the attenuation negligibly small. An experimental prototype for on-board optical-to-electrical signal broadcasting operating at 10Gb/s per channel over an interconnect distance of 10cm is demonstrated. An improved 1 x 4 multimode interference (MMI) splitter at 1550nm with linearly-tapered output facet is heterogeneously integrated with four p-i-n photodetectors (PDs) on a Silicon (Si) bench. The Si bench itself is hybrid integrated onto an FR-4 printed-circuit board with four receiver channels. A novel fabrication/integration approach demonstrates the simultaneous alignment between the four waveguides and the four PDs during the MMI fabrication process. The entire system is fully functional at 10Gb/s.

Silicon Mach-Zehnder interferometer racetrack microring for sensing

NASA Astrophysics Data System (ADS)

Xiong, Yule; Ye, Winnie N.

2014-03-01

SOI-based microring resonators (MRRs) have attracted extensive attentions as ultra-compact sensors. Recently, a new structure design combining a ring and a Mach-Zehnder interferometer (MZI) was proposed as sensors for biomedical applications, and as modulators for communications applications. In this design, the MZI uses two identical couplers, where one arm is formed by connecting the access waveguide of the couplers, while the other arm is part of the microring. Such a device may have only one major resonance with a high extinction ratio in a very broad wavelength span (quasi-free spectral range, quasi-FSR), which offers a very large measurement range for sensing applications. 2×2 multimode interference (MMI) couplers are used to couple the microring and the bus waveguides as MMI couplers have broader wavelength responses. We present the first experimental demonstration of the MMI-coupled MZI racetrack microrings for sensing applications. Two types of MMI-coupled MZI racetrack microrings are discussed: one with wire waveguides, and the other using slotted waveguides. For the MZI racetrack microring using wire waveguides, we achieve a quasi-FSR of 34.3 nm near the wavelength of 1520 nm. The corresponding major resonance of the MZI racetrack microring demonstrates a high extinction ratio of ~22.4 dB with a full-width-half-maximum (FWHM) of 1.94 nm, and a quality factor Q of ~800. On the other hand, the quasi-FSR of the MZI racetrack microring with slot waveguides is 23.2 nm near the wavelength of 1540 nm; and the extinction ratio of the major resonance is ~24.5 dB with λFWHM=0.82 nm and Q=~1,900. To demonstrate the uses for sensing applications, we measure the resonance shifts corresponding to the concentration change of the ambient aqueous solutions of sucrose. DI water is used as the reference for calibration to avoid any other variations, e.g. temperature change. Experiments show that the sensitivities of the MZI racetrack microring sensors with wire and slot waveguides are 101.7 nm/RIU and 166.7 nm/RIU, respectively.

Optofluidic devices for biomolecule sensing and multiplexing

NASA Astrophysics Data System (ADS)

Ozcelik, Damla

Optofluidics which integrates photonics and microfluidics, has led to highly compact, sensitive and adaptable biomedical sensors. Optofluidic biosensors based on liquid-core anti-resonant reflecting optical waveguides (LC-ARROWs), have proven to be a highly sensitive, portable, and reconfigurable platform for fluorescence spectroscopy and detection of single biomolecules such as proteins, nucleic acids, and virus particles. However, continued improvements in sensitivity remain a major goal as we approach the ultimate limit of detecting individual bio-particles labeled by single or few fluorophores. Additionally, the ability to simultaneously detect and identify multiple biological particles or biomarkers is one of the key requirements for molecular diagnostic tests. The compactness and adaptability of these platforms can further be advanced by introducing tunability, integrating off-chip components, designing reconfigurable and customizable devices, which makes these platforms very good candidates for many different applications. The goal of this thesis was to introduce new elements in these LC-ARROW optofluidics platforms that provide major enhancements in their functionality, making them more sensitive, compact, customizable and multiplexed. First, a novel integrated tunable spectral filter that achieves effective elimination of background noise on the ARROW platform was demonstrated. A unique dual liquid-core design enabled the independent multi-wavelength tuning of the spectral filter by adjusting the refractive index and chemical properties of the liquid. In order to enhance the detection sensitivity of the platform, Y-splitter waveguides were integrated to create multiple excitation spots for each target molecule. A powerful signal processing algorithm was used to analyze the data to improve the signal-to-noise ratio (SNR) of the collected data. Next, the design, optimization and characterization of the Y-splitter waveguides are presented; and single influenza virus detection with an improved SNR was demonstrated using this platform. Finally, multiplexing capacity is introduced to the ARROW detection platform by integrating multi-mode interference (MMI) waveguides. MMI waveguides create wavelength dependent multiple excitation spots at the excitation region, allowing the spectral multiplexed detection of multiple different target molecules based on the excitation pattern, without the need for additional spectral filters. Successful spectral multiplexed detection of three different types of influenza viruses is achieved by using separate wavelengths and combination of wavelengths. This multiplexing capacity is further enhanced by taking advantage of the spatial properties of the MMI pattern, designing triple liquid-core waveguides that intersect the MMI waveguide in different locations. Furthermore, the spectral and spatial multiplexing capacities are combined in these triple liquid-core MMI platforms, allowing these devices to distinguish multiple different targets and samples simultaneously.

Resonance Frequency Tuning of a Double Ring Resonator in GaInAsP/InP: Experiment and Simulation

NASA Astrophysics Data System (ADS)

Rabus, Dominik Gerhard; Hamacher, Michael; Heidrich, Helmut

2002-02-01

A racetrack shaped double ring resonator (DRR) filter is demonstrated with radii of 200 μm. The double ring resonator contains two -3 dB multimode interference (MMI) couplers for I/O coupling and a -13 dB codirectional coupler in between the rings. A free spectral range of 50 GHz has been realized. A simulation model has been developed to describe the DRR. As fabrication tolerances do not allow the realization of two identical rings with required nm-circumference accuracy in the resonator, a frequency alignment of the resonator is indispensable. The resonance frequency tuning is performed thermally using platinum resistors which have been placed on top of the waveguides in both rings. An on-off ratio increase has been achieved of more than 3 dB, resulting in a total on-off ratio larger than 18 dB. The frequency alignment is inevitable in the case of multiple coupled micro ring resonators.

Biosensing Using Microring Resonator Interferograms

PubMed Central

Hsu, Shih-Hsiang; Yang, Yung-Chia; Su, Yu-Hou; Wang, Sheng-Min; Huang, Shih-An; Lin, Ching-Yu

2014-01-01

Optical low-coherence interferometry (OLCI) takes advantage of the variation in refractive index in silicon-wire microring resonator (MRR) effective lengths to perform glucose biosensing using MRR interferograms. The MRR quality factor (Q), proportional to the effective length, could be improved using the silicon-wire propagation loss and coupling ratio from the MRR coupler. Our study showed that multimode interference (MMI) performed well in broad band response, but the splitting ratio drifted to 75/25 due to the stress issue. The glucose sensing sensitivity demonstrated 0.00279 meter per refractive-index-unit (RIU) with a Q factor of ∼30,000 under transverse electric polarization. The 1,310 nm DFB laser was built in the OLCI system as the optical ruler achieving 655 nm characterization accuracy. The lowest sensing limitation was therefore 2 × 10−4 RIU. Moreover, the MRR effective length from the glucose sensitivity could be utilized to experimentally demonstrate the silicon wire effective refractive index with a width of 0.45 μm and height of 0.26 μm. PMID:24434876

Thermo-optic devices on polymer platform

NASA Astrophysics Data System (ADS)

Zhang, Ziyang; Keil, Norbert

2016-03-01

Optical polymers possess in general relatively high thermo-optic coefficients and at the same time low thermal conductivity, both of which make them attractive material candidates for realizing highly efficient thermally tunable devices. Over the years, various thermo-optic components have been demonstrated on polymer platform, covering (1) tunable reflectors and filters as part of a laser cavity, (2) variable optical attenuators (VOAs) as light amplitude regulators in e.g. a coherent receiver, and (3) thermo-optic switches (TOSs) allowing multi-flow control in the photonic integrated circuits (PICs). This work attempts to review the recent progress on the above mentioned three component branches, including linearly and differentially tunable filters, VOAs based on 1×1 multimode interference structure (MMI) and Mach-Zehnder interferometer (MZI), and 1×2 TOS based on waveguide Y-branch, driven by a pair of sidelong placed heater electrodes. These thermo-optic components can well be integrated into larger PICs: the dual-polarization switchable tunable laser and the colorless optical 90° hybrid are presented in the end as examples.

Tunable fiber laser based on the refractive index characteristic of MMI effects

NASA Astrophysics Data System (ADS)

Ma, Lin; Qi, Yanhui; Kang, Zexin; Bai, Yunlong; Jian, Shuisheng

2014-04-01

A tunable erbium-doped all-fiber laser has been demonstrated. This tunable laser is based on a tunable fiber filter using the refractive index characteristics of multimode interference effects. A thinner no-core fiber with a diameter of 104 μm is used to fabricate the tunable fiber filter. The joint point of the thinner no-core fiber with SMF is a taper, which improves its sensitivity for refractive index changes. The filter exhibits a very sensitive response to the change of the environmental refractive index, which is about 1000 nm/RIU in the RI range from 1.418 to 1.427. The tunable fiber laser based on the filter achieved a tunability of 32 nm, with the wavelength tuned from 1532 nm to 1564 nm covering the full C-band. The 3 dB bandwidth of the tunable laser is less than 0.02 nm with the signal-to-noise ratio of about 40 dB.

Resolution improvement in positron emission tomography using anatomical Magnetic Resonance Imaging.

PubMed

Chu, Yong; Su, Min-Ying; Mandelkern, Mark; Nalcioglu, Orhan

2006-08-01

An ideal imaging system should provide information with high-sensitivity, high spatial, and temporal resolution. Unfortunately, it is not possible to satisfy all of these desired features in a single modality. In this paper, we discuss methods to improve the spatial resolution in positron emission imaging (PET) using a priori information from Magnetic Resonance Imaging (MRI). Our approach uses an image restoration algorithm based on the maximization of mutual information (MMI), which has found significant success for optimizing multimodal image registration. The MMI criterion is used to estimate the parameters in the Sharpness-Constrained Wiener filter. The generated filter is then applied to restore PET images of a realistic digital brain phantom. The resulting restored images show improved resolution and better signal-to-noise ratio compared to the interpolated PET images. We conclude that a Sharpness-Constrained Wiener filter having parameters optimized from a MMI criterion may be useful for restoring spatial resolution in PET based on a priori information from correlated MRI.

Free space and waveguide Talbot effect: phase relations and planar light circuit applications

NASA Astrophysics Data System (ADS)

Nikkhah, H.; Zheng, Q.; Hasan, I.; Abdul-Majid, S.; Hall, T. J.

2012-10-01

Optical fields that are periodic in the transverse plane self-image periodically as they propagate along the optical axis: a phenomenon known as the Talbot effect. A transfer matrix may be defined that relates the amplitude and phase of point sources placed on a particular grid at the input to their respective multiple images at an image plane. The free-space Talbot effect may be mapped to the waveguide Talbot effect. Applying this mapping to the transfer matrix enables the prediction of the phase and amplitude relations between the ports of a Multimode Interference (MMI) coupler- a planar waveguide device. The transfer matrix approach has not previously been applied to the free-space case and its mapping to the waveguide case provides greater clarity and physical insight into the phase relationships than previous treatments. The paper first introduces the underlying physics of the Talbot effect in free space with emphasis on the positions along the optical axis at which images occur; their multiplicity; and their relative phase relations determined by the Gauss Quadratic Sum of number theory. The analysis is then adapted to predict the phase relationships between the ports of an MMI. These phase relationships are critical to planar light circuit (PLC) applications such as 90° optical hybrids for coherent optical receiver front-ends, external optical I-Q modulators for coherent optical transmitters; and optical phased array switches. These applications are illustrated by results obtained from devices that have been fabricated and tested by the PTLab in Si micro-photonic integration platforms.

MMI-based MOEMS FT spectrometer for visible and IR spectral ranges

NASA Astrophysics Data System (ADS)

Al-Demerdash, Bassem M.; Medhat, Mostafa; Sabry, Yasser M.; Saadany, Bassam; Khalil, Diaa

2014-03-01

MEMS spectrometers have very strong potential in future healthcare and environmental monitoring applications, where Michelson interferometers are the core optical engine. Recently, MEMS Michelson interferometers based on using silicon interface as a beam splitter (BS) has been proposed [7, 8]. This allows having a monolithically-integrated on-chip FTIR spectrometer. However silicon BS exhibits high absorption loss in the visible range and high material dispersion in the near infrared (NIR) range. For this reason, we propose in this work a novel MOEMS interferometer allowing operation over wider spectral range covering both the infrared (IR) and the visible ranges. The proposed architecture is based on spatial splitting and combining of optical beams using the imaging properties of Multi-Mode Interference MMI waveguide. The proposed structure includes an optical splitter for spatial splitting an input beam into two beams and a combiner for spatial combining the two interferometer beams. A MEMS moveable mirror is provided to produce an optical path difference between the two beams. The new interferometer is fabricated using DRIE technology on an SOI wafer. The movable mirror is metalized and attached to a comb-drive actuator fabricated in the same lithography step in a self-aligned manner on chip. The novel interferometer is tested as a Fourier transform spectrometer. Red laser, IR laser and absorption spectra of different materials are measured with a resolution of 2.5 nm at 635-nm wavelength. The structure is a very compact one that allows its integration and fabrication on a large scale with very low cost.

Photonic crystal fiber refractive-index sensor based on multimode interferometry

NASA Astrophysics Data System (ADS)

Gong, Zhenfeng; Zhang, Xinpu; Liu, Yun; Liu, Zigeng; Peng, Wei

2014-11-01

We report a type of multimode fiber interferometers (MMI) formed in photonic crystal fiber (PCF). To excite the cladding modes from the fundamental core mode of a PCF, a coupling point is formed. To form the coupling point, we used the method that is blowing compressed gas into the air-holes and discharging at one point, and the air-holes in this point will expand due to gas expansion in the discharge process. By placing two coupling points in series, a very simple all-fiber MMI can be implemented. The detailed fabrication process is that the one end of the PCF is tightly sealed by a short section of single mode fiber (SMF) spliced to the PCF. The other end of the PCF is sealed into a gas chamber and the opened air holes are pressurized. The PCF is then heated locally by the fusion splicer and the holes with higher gas pressure will expand locally where two bubbles formed. We tested the RI responses of fabricated sensors at room temperature by immersing the sensor into solutions with different NaCl concentration. Experimental results show that as refractive-index (RI) increases, the resonance wavelength of the MMI moves toward longer wavelengths. The sensitivity coefficients are estimated by the linear fitting line, which is 46nm/RIU, 154mn/RIU with the interferometer lengths (IL) of 3mm and 6mm. The interferometer with larger IL has higher RI sensitivity. The temperature cross-sensitivity of the sensor is also tested. The temperature sensitivity can be as low as -16.0pm/°C.

Femtosecond laser inscription of optical circuits in the cladding of optical fibers

NASA Astrophysics Data System (ADS)

Grenier, Jason R.

The aim of this dissertation was to address the question of whether the cladding of single-mode fibers (SMFs) could be modified to enable optical fibers to serve as a more integrated, highly functional platform for optical circuit devices that can efficiently interconnect with the pre-existing fiber core waveguide. The approach adopted in this dissertation was to employ femtosecond laser direct writing (FLDW), an inherently 3D fabrication technique that harnesses non-linear laser-material interactions to modify the fused silica fiber cladding. A fiber mounting and alignment technique was developed along with oil-immersion focusing to address the strong aberrations caused by the cylindrical fiber shape. The development of real-time device monitoring during the FLDW was instrumental to overcome the acute coupling sensitivity to laser alignment errors of +/-1 ?m positional uncertainty, and thereby opened a new practical direction for the precise fabrication of optical devices inside optical fibers. These powerful and flexible laser fabrication and characterization techniques were successfully employed to optimize optical waveguiding devices positioned within the core and cladding of optical fibers. X-, S-Bend, and directional couplers were developed to enable efficient coupling between the laser-formed cladding devices and the pre-existing core waveguide, enabling up to 62% power transfer over bandwidths up to 300 nm at telecommunication wavelengths. Precise alignment of femtosecond laser modification tracks were positioned inside or near the core waveguide of SMFs was further shown to enable a flexible reshaping of the optical properties to create multimode guiding sections arbitrarily along the fiber length. This core waveguide modification facilitated the precise formation of multimode interferometers along the core waveguide to precisely tailor the modal profiles, and control the spectral and polarization response. In-fiber multimode interference (MMI) splitters and couplers were fabricated with coupling ratios from 2% to 50% over a broad 350 nm bandwidth across the telecommunication band. Laser-induced birefringence was harnessed to generate polarization dependent MMI devices for strong polarization filtering (24 dB isolation), or polarization selective taps with up to 50% tapping efficiency over a 25 nm bandwidth. This dissertation is therefore the first demonstration of femtosecond laser direct writing as a flexible and monolithic means of embedding and integrating highly functional optical circuit devices within the cladding of optical fibers that can interconnect efficiently with the pre-existing fiber core waveguide. These developments represent a significant technological advancement for creating new 3D photonic integrated microsystems within the cladding of optical fibers and underpins a new technological platform of fiber cladding photonics.

Dual-point reflective refractometer based on parallel no-core fiber/FBG structure

NASA Astrophysics Data System (ADS)

Guo, Cuijuan; Niu, Panpan; Wang, Juan; Zhao, Junfa; Zhang, Cheng

2018-01-01

A novel dual-point reflective fiber-optic refractometer based on multimode interference (MMI) effect and fiber Bragg grating (FBG) reflection is proposed and experimentally demonstrated, which adopts parallel structure. Each point of the refractometer consists of a single mode-no core-single mode fiber (SNS) structure cascaded with a FBG. Assisted by the reflection of FBG, refractive index (RI) measurement can be achieved by monitoring the peak power variation of the reflected FBG spectrum. By selecting different length of the no core fiber and center wavelength of the FBG, independent dual-point refractometer is easily realized. Experiment results show that the refractometer has a nonlinear relationship between the surrounding refractive index (SRI) and the peak power of the reflected FBG spectrum in the RI range of 1.3330-1.4086. Linear relationship can be approximately obtained by dividing the measuring range into 1.3330-1.3611 and 1.3764-1.4086. In the RI range of 1.3764-1.4086, the two sensing points have higher RI sensitivities of 319.34 dB/RIU and 211.84 dB/RIU, respectively.

Analysis of hybrid dielectric-plasmonic slot waveguide structures with 3D Fourier Modal Methods

NASA Astrophysics Data System (ADS)

Ctyroky, J.; Kwiecien, P.; Richter, I.

2013-03-01

Recently, plasmonic waveguides have been intensively studied as promising basic building blocks for the construction of extremely compact photonic devices with subwavelength characteristic dimensions. A number of different types of plasmonic waveguide structures have been recently proposed, theoretically analyzed, and their properties experimentally verified. The fundamental trade-off in the design of plasmonic waveguides for potential application in information technologies lies in the contradiction between their mode field confinement and propagation loss: the higher confinement, the higher loss, and vice versa. Various definitions of figures of merit of plasmonic waveguides have been also introduced for the characterization of their properties with a single quantity. In this contribution, we theoretically analyze one specific type of a plasmonic waveguide - the hybrid dielectric-loaded plasmonic waveguide, or - as we call it in this paper - the hybrid dielectric-plasmonic slot waveguide, which exhibits very strong field confinement combined with acceptable losses allowing their application in some integrated plasmonic devices. In contrast to the structures analyzed previously, our structure makes use of a single low-index dielectric only. We first define the effective area of this waveguide type, and using waveguide parameters close to the optimum we analyze several waveguide devices as directional couplers, multimode interference couplers (MMI), and the Mach-Zehnder interferometer based on the MMI couplers. For the full-vector 3D analysis of these structures, we use modelling tools developed in-house on the basis of the Fourier Modal Method (FMM). Our results thus serve to a dual purpose: they confirm that (i) these structures represent promising building blocks of plasmonic devices, and (ii) our FMM codes are capable of efficient 3D vector modelling of plasmonic waveguide devices.

Global optimization of multimode interference structure for ratiometric wavelength measurement

NASA Astrophysics Data System (ADS)

Wang, Qian; Farrell, Gerald; Hatta, Agus Muhamad

2007-07-01

The multimode interference structure is conventionally used as a splitter/combiner. In this paper, it is optimised as an edge filter for ratiometric wavelength measurement, which can be used in demodulation of fiber Bragg grating sensing. The global optimization algorithm-adaptive simulated annealing is introduced in the design of multimode interference structure including the length and width of the multimode waveguide section, and positions of the input and output waveguides. The designed structure shows a suitable spectral response for wavelength measurement and a good fabrication tolerance.

Design issues of a multimode interference-based 3-dB splitter.

PubMed

Themistos, Christos; Rahman, B M Azizur

2002-11-20

We have investigated important issues such as the power loss, the loss imbalance the fabrication tolerances, and the wavelength dependence for the design of a multimode interference-based 3-dB splitter on deeply etched InP waveguides under general, restricted, and symmetric interference mechanisms. For this investigation, we used the finite-element-based beam propagation approach. Results are presented.

Optical sensor in planar configuration based on multimode interference

NASA Astrophysics Data System (ADS)

Blahut, Marek

2017-08-01

In the paper a numerical analysis of optical sensors based on multimode interference in planar one-dimensional step-index configuration is presented. The structure consists in single-mode input and output waveguides and multimode waveguide which guide only few modes. Material parameters discussed refer to a SU8 polymer waveguide on SiO2 substrate. The optical system described will be designed to the analysis of biological substances.

Hybrid optofluidic biosensors

NASA Astrophysics Data System (ADS)

Parks, Joshua W.

Optofluidics, born of the desire to create a system containing microfluidic environments with integrated optical elements, has seen dramatic increases in popularity over the last 10 years. In particular, the application of this technology towards chip based molecular sensors has undergone significant development. The most sensitive of these biosensors interface liquid- and solid-core antiresonant reflecting optical waveguides (ARROWs). These sensor chips are created using conventional silicon microfabrication. As such, ARROW technology has previously been unable to utilize state-of-the-art microfluidic developments because the technology used--soft polydimethyl siloxane (PDMS) micromolded chips--is unamenable to the silicon microfabrication workflows implemented in the creation of ARROW detection chips. The original goal of this thesis was to employ hybrid integration, or the connection of independently designed and fabricated optofluidic and microfluidic chips, to create enhanced biosensors with the capability of processing and detecting biological samples on a single hybrid system. After successful demonstration of this paradigm, this work expanded into a new direction--direct integration of sensing and detection technologies on a new platform with dynamic, multi-dimensional photonic re-configurability. This thesis reports a number of firsts, including: • 1,000 fold optical transmission enhancement of ARROW optofluidic detection chips through thermal annealing, • Detection of single nucleic acids on a silicon-based ARROW chip, • Hybrid optofluidic integration of ARROW detection chips and passive PDMS microfluidic chips, • Hybrid optofluidic integration of ARROW detection chips and actively controllable PDMS microfluidic chips with integrated microvalves, • On-chip concentration and detection of clinical Ebola nucleic acids, • Multimode interference (MMI) waveguide based wavelength division multiplexing for detection of single influenza virions, • All PDMS platform created from monolithically integrated solid- and liquid-core waveguides with single particle detection efficiency and directly integrated microvalves, featuring: ∘ Tunable/tailorable PDMS MMI waveguides, ∘ Lightvalves (optical switch/fluidic microvalve) with the ability to dynamically control light and fluid flow simultaneously, ∘ Lightvalve trap architecture with the ability to physically trap, detect, and analyze single biomolecules.

Chiral spiral waveguides based on MMI crossings: theory and experiments

NASA Astrophysics Data System (ADS)

Cherchi, Matteo; Ylinen, Sami; Harjanne, Mikko; Kapulainen, Markku; Vehmas, Tapani; Aalto, Timo

2016-03-01

We introduce a novel type of chiral spiral waveguide where the usual waveguide crossings are replaced by 100:0 Multimode Interferometers (MMIs), i.e. 2x2 splitters that couple all the input light in the cross output port. Despite the topological equivalence with the standard configuration, we show how resorting to long MMIs has non-trivial advantages in terms of footprint and propagation length. An accurate analytic model is also introduced to show the impact of nonidealities on the spiral performances, including propagation loss and cross-talk. We have designed and fabricated three chiral spirals on our platform, based on 3 μm thick silicon strip waveguides with 0.13 dB/cm propagation loss, and 1.58 mm long MMIs. The fabricated spirals have 7, 13 and 49 loops respectively, corresponding to the effective lengths 6.6 cm, 12.5 cm and 47.9 cm. The proposed model is successfully applied to the experimental results, highlighting MMI extinction ratio of about 16.5 dB and MMI loss of about 0.08 dB, that are much worse compared to the simulated 50 dB extinction and 0.01 dB loss. This imposes an upper limit to the number of rounds, because light takes shortcuts through the bar MMI ports. Nevertheless, the novel chiral spiral waveguides outperform what is achievable in mainstream silicon photonics platforms based on submicron waveguides in terms of length and propagation losses, and they are promising candidates for the realization of integrated gyroscopes. They can be significantly further improved by replacing the MMIs with adiabatic 100:0 splitters, ensuring lower cross-talk and broader bandwidth.

Note: Broadly tunable all-fiber ytterbium laser with 0.05 nm spectral width based on multimode interference filter.

PubMed

Mukhopadhyay, Pranab K; Gupta, Pradeep K; Singh, Amarjeet; Sharma, Sunil K; Bindra, Kushvinder S; Oak, Shrikant M

2014-05-01

A multimode interference filter with narrow transmission bandwidth and large self-imaging wavelength interval is constructed and implemented in an ytterbium doped fiber laser in all-fiber format for broad wavelength tunability as well as narrow spectral width of the output beam. The peak transmission wavelength of the multimode interference filter was tuned with the help of a standard in-fiber polarization controller. With this simple mechanism more than 30 nm (1038 nm-1070 nm) tuning range is demonstrated. The spectral width of the output beam from the laser was measured to be 0.05 nm.

Note: Broadly tunable all-fiber ytterbium laser with 0.05 nm spectral width based on multimode interference filter

NASA Astrophysics Data System (ADS)

Mukhopadhyay, Pranab K.; Gupta, Pradeep K.; Singh, Amarjeet; Sharma, Sunil K.; Bindra, Kushvinder S.; Oak, Shrikant M.

2014-05-01

A multimode interference filter with narrow transmission bandwidth and large self-imaging wavelength interval is constructed and implemented in an ytterbium doped fiber laser in all-fiber format for broad wavelength tunability as well as narrow spectral width of the output beam. The peak transmission wavelength of the multimode interference filter was tuned with the help of a standard in-fiber polarization controller. With this simple mechanism more than 30 nm (1038 nm-1070 nm) tuning range is demonstrated. The spectral width of the output beam from the laser was measured to be 0.05 nm.

Note: Broadly tunable all-fiber ytterbium laser with 0.05 nm spectral width based on multimode interference filter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mukhopadhyay, Pranab K., E-mail: pkm@rrcat.gov.in; Gupta, Pradeep K.; Singh, Amarjeet

2014-05-15

A multimode interference filter with narrow transmission bandwidth and large self-imaging wavelength interval is constructed and implemented in an ytterbium doped fiber laser in all-fiber format for broad wavelength tunability as well as narrow spectral width of the output beam. The peak transmission wavelength of the multimode interference filter was tuned with the help of a standard in-fiber polarization controller. With this simple mechanism more than 30 nm (1038 nm–1070 nm) tuning range is demonstrated. The spectral width of the output beam from the laser was measured to be 0.05 nm.

Fully integrated multi-optoelectronic synthesizer for THz pumping source in wireless communications with rich backup redundancy and wide tuning range.

PubMed

Xu, Junjie; Hou, Lianping; Deng, Qiufang; Han, Liangshun; Liang, Song; Marsh, John H; Zhu, Hongliang

2016-07-06

We report a monolithic photonic integrated circuit (PIC) for THz communication applications. The PIC generates up to 4 optical frequency lines which can be mixed in a separate device to generate THz radiation, and each of the optical lines can be modulated individually to encode data. Physically, the PIC comprises an array of wavelength tunable distributed feedback lasers each with its own electro-absorption modulator. The lasers are designed with a long cavity to operate with a narrow linewidth, typically <4 MHz. The light from the lasers is coupled via an multimode interference (MMI) coupler into a semiconductor optical amplifier (SOA). By appropriate selection and biasing of pairs of lasers, the optical beat signal can be tuned continuously over the range from 0.254 THz to 2.723 THz. The EAM of each channel enables signal leveling balanced between the lasers and realizing data encoding, currently at data rates up to 6.5 Gb/s. The PIC is fabricated using regrowth-free techniques, making it economic for volume applications, such for use in data centers. The PIC also has a degree of redundancy, making it suitable for applications, such as inter-satellite communications, where high reliability is mandatory.

Counting statistics of many-particle quantum walks

NASA Astrophysics Data System (ADS)

Mayer, Klaus; Tichy, Malte C.; Mintert, Florian; Konrad, Thomas; Buchleitner, Andreas

2011-06-01

We study quantum walks of many noninteracting particles on a beam splitter array as a paradigmatic testing ground for the competition of single- and many-particle interference in a multimode system. We derive a general expression for multimode particle-number correlation functions, valid for bosons and fermions, and infer pronounced signatures of many-particle interferences in the counting statistics.

FIBER AND INTEGRATED OPTICS: Analysis of the characteristics of a radio signal at the output of a multimode interference-type fiber channel

NASA Astrophysics Data System (ADS)

Bratchikov, A. N.; Glukhov, I. P.

1992-02-01

An analysis is made of a theoretical model of an interference fiber channel for transmission of microwave signals. It is assumed that the channel consists of a multimode fiber waveguide with a step or graded refractive-index profile. A typical statistic of a longitudinal distribution of inhomogeneities is also assumed. Calculations are reported of the interference losses, the spectral profile of the output radio signal, the signal/noise ratio in the channel, and of the dependences of these parameters on: the type, diameter, and the length of the multimode fiber waveguide; the spectral width of the radiation source; the frequency offset between the interfering optical signals.

Optimization of an integrated wavelength monitor device

NASA Astrophysics Data System (ADS)

Wang, Pengfei; Brambilla, Gilberto; Semenova, Yuliya; Wu, Qiang; Farrell, Gerald

2011-05-01

In this paper an edge filter based on multimode interference in an integrated waveguide is optimized for a wavelength monitoring application. This can also be used as a demodulation element in a fibre Bragg grating sensing system. A global optimization algorithm is presented for the optimum design of the multimode interference device, including a range of parameters of the multimode waveguide, such as length, width and position of the input and output waveguides. The designed structure demonstrates the desired spectral response for wavelength measurements. Fabrication tolerance is also analysed numerically for this structure.

Research on high-temperature sensing characteristics based on modular interference of single-mode multimode single-mode fiber

NASA Astrophysics Data System (ADS)

Peng, Zhaozhuang; Wang, Li; Yan, Huanhuan

2016-11-01

Application of high temperature fiber sensing system is very extensive. It can be mainly used in high temperature test aerospace, such as, materials, chemicals, and energy. In recent years, various on-line optical fiber interferometric sensors based on modular interference of single-mode-multimode-single-mode(SMS) fiber have been largely explored in high temperature fiber sensor. In this paper we use the special fiber of a polyimide coating, its sensor head is composed of a section of multimode fiber spliced in the middle of Single-mode fiber. When the light is launched into the multimode fiber(MMF) through the lead-in single-mode fiber(SMF), the core mode and cladding modes are excited and propagate in the MMF respectively. Then, at the MMF-SMF spliced point, the excited cladding modes coupled back into the core of lead-out SMF interfere with SMF core mode. And the wavelength of the interference dip would shift differently with the variation of the temperature. By this mean, we can achieve the measurement of temperature. The experimental results also show that the fiber sensor based on SMS structure has a highly temperature sensitivity. From 30° to 300°, with the temperature increasing, the interference dip slightly shifts toward longer wavelength and the temperature sensitivity coefficient is 0.0115nm/°. With high sensitivity, simple structure, immunity to electromagnetic interferences and a good linearity of the experimental results, the structure has an excellent application prospect in engineering field.

Passively Q-switched dual-wavelength thulium-doped fiber laser based on a multimode interference filter and a semiconductor saturable absorber

NASA Astrophysics Data System (ADS)

Wang, M.; Huang, Y. J.; Ruan, S. C.

2018-04-01

In this paper, we have demonstrated a theta cavity passively Q-switched dual-wavelength fiber laser based on a multimode interference filter and a semiconductor saturable absorber. Relying on the properties of the fiber theta cavity, the laser can operate unidirectionally without an optical isolator. A semiconductor saturable absorber played the role of passive Q-switch while a section of single-mode-multimode-single-mode fiber structure served as an multimode interference filter and was used for selecting the lasing wavelengths. By suitably manipulating the polarization controller, stable dual-wavelength Q-switched operation was obtained at ~1946.8 nm and ~1983.8 nm with maximum output power and minimum pulse duration of ~47 mW and ~762.5 ns, respectively. The pulse repetition rate can be tuned from ~20.2 kHz to ~79.7 kHz by increasing the pump power from ~2.12 W to ~5.4 W.

Design and characterization of Ge passive waveguide components on Ge-on-insulator wafer for mid-infrared photonics

NASA Astrophysics Data System (ADS)

Kang, Jian; Takagi, Shinichi; Takenaka, Mitsuru

2018-04-01

We present the design methodology for Ge passive components including single-mode waveguide, grating couplers, multimode interferometer (MMI) couplers, and micro-ring resonators on the Ge-on-insulator wafer at a 1.95 µm wavelength. Characterizations of the fabricated Ge passive devices reveal a good consistence between the experimental and simulation results. By using the Ge micro-ring device, we also reveal that the thermo-optic coefficient in the Ge strip waveguide is 5.74 × 10-4/°C, which is much greater than that in Si.

Multimode interference tapered fiber refractive index sensors.

PubMed

Biazoli, Claudecir R; Silva, Susana; Franco, Marcos A R; Frazão, Orlando; Cordeiro, Cristiano M B

2012-08-20

Real-time monitoring of the fabrication process of tapering down a multimode-interference-based fiber structure is presented. The device is composed of a pure silica multimode fiber (MMF) with an initial 125 μm diameter spliced between two single-mode fibers. The process allows a thin MMF with adjustable parameters to obtain a high signal transmittance, arising from constructive interference among the guided modes at the output end of the MMF. Tapered structures with waist diameters as low as 55 μm were easily fabricated without the limitation of fragile splices or difficulty in controlling lateral fiber alignments. The sensing device is shown to be sensitive to the external environment, and a maximum sensitivity of 2946 nm/refractive index unit in the refractive index range of 1.42-1.43 was attained.

Reconfigurable and tunable compact comb filter and (de)interleaver on silicon platform.

PubMed

Zhou, Nan; Zheng, Shuang; Long, Yun; Ruan, Zhengsen; Shen, Li; Wang, Jian

2018-02-19

We propose and demonstrate a reconfigurable and tunable chip-scale comb filter and (de)interleaver on a silicon platform. The silicon-based photonic integrated device is formed by Sagnac loop mirrors (SLMs) with directional couplers replaced by multi-mode interference (MMI) assisted tunable Mach-Zehnder interferometer (MZI) couplers. The device can be regarded as a large SLM incorporating two small SLMs which form a Fabry-Perot (FP) cavity. By appropriately adjusting the micro-heaters in tunable MZI couplers and cavity, switchable operation between comb filter and (de)interleaver and extinction ratio and wavelength tunable operations of comb filter and (de)interleaver are achievable by thermo-optic tuning. Reconfigurable comb filter and (de)interleaver is demonstrated in the experiment. The central wavelength shifts of comb filter and (de)interleaver are demonstrated with wavelength tuning efficiencies of ~0.0224 nm/mW and ~0.0193 nm/mW, respectively. The 3-dB bandwidth of the comb filter is ~0.032 nm. The 3-dB and 20-dB bandwidths of the (de)interleaver passband are ~0.225 nm and ~0.326 nm. The obtained results indicate that the designed and fabricated device provides switchable comb filtering and interleaving functions together with extinction ratio and wavelength tunabilities. Reconfigurable and tunable silicon-based comb filter and (de)interleaver may find potential applications in robust wavelength-division multiplexing (WDM) optical communication systems.

Tunable all-fiber dissipative-soliton laser with a multimode interference filter.

PubMed

Zhang, Lei; Hu, Jinmeng; Wang, Jianhua; Feng, Yan

2012-09-15

We report on a tunable all-fiber dissipative-soliton laser with a multimode interference filter that consists of a multimode fiber spliced between two single-mode fibers. By carefully selecting the fiber parameters, a filter with a central wavelength at 1032 nm and a bandwidth of 7.6 nm is constructed and used for spectral filtering in an all-normal-dispersion mode-locked ytterbium-doped fiber laser based on nonlinear polarization evolution. The laser delivers 31 mW of average output power with positively chirped 7 ps pulses. The repetition rate of the pulses is 15.3 MHz, and pulse energy is 2.1 nJ. Tunable dissipative-soliton over 12 nm is achieved by applying tension to the single-mode-multimode-single-mode filter.

Quantum optics of lossy asymmetric beam splitters.

PubMed

Uppu, Ravitej; Wolterink, Tom A W; Tentrup, Tristan B H; Pinkse, Pepijn W H

2016-07-25

We theoretically investigate quantum interference of two single photons at a lossy asymmetric beam splitter, the most general passive 2×2 optical circuit. The losses in the circuit result in a non-unitary scattering matrix with a non-trivial set of constraints on the elements of the scattering matrix. Our analysis using the noise operator formalism shows that the loss allows tunability of quantum interference to an extent not possible with a lossless beam splitter. Our theoretical studies support the experimental demonstrations of programmable quantum interference in highly multimodal systems such as opaque scattering media and multimode fibers.

Treatment and management of thyroid storm: analysis of the nationwide surveys: The taskforce committee of the Japan Thyroid Association and Japan Endocrine Society for the establishment of diagnostic criteria and nationwide surveys for thyroid storm.

PubMed

Isozaki, Osamu; Satoh, Tetsurou; Wakino, Shu; Suzuki, Atsushi; Iburi, Tadao; Tsuboi, Kumiko; Kanamoto, Naotetsu; Otani, Hajime; Furukawa, Yasushi; Teramukai, Satoshi; Akamizu, Takashi

2016-06-01

Thyroid storm (TS) is a life-threatening endocrine emergency. This study aimed to achieve a better understanding of the management of TS by analyzing therapeutic modalities and prognoses reported by nationwide surveys performed in Japan. Retrospective analyses were performed on clinical parameters, outcomes, and treatments in 356 TS patients. Patient disease severities assessed via Acute Physiology and Chronic Health Evaluation (APACHE) II and Sequential Organ Failure Assessment (SOFA) scores significantly correlated with mortality. Free triiodothyronine (FT3) and the FT3/free thyroxine (FT4) ratio inversely correlated with disease severity. Methimazole (MMI) was used in the majority of patients (78·1%), and there were no significant differences in mortality or disease severity between those treated with MMI and those receiving propylthiouracil (PTU). Patients who received inorganic iodide (KI) demonstrated higher disease severity but no change in mortality compared to those who did not. Patients treated with corticosteroids (CSs) demonstrated significantly higher disease severity and mortality than those who were not. Disease severity in patients treated with intravenous administration of beta-adrenergic antagonists (AAs) was significantly higher than those treated with oral preparations, although no significant difference in mortality was observed between these groups. In addition, mortality was significantly higher in patients treated with non-selective beta-AAs as compared with other types of beta-AAs. In Japan, MMI was preferentially used in TS and showed no disadvantages compared to PTU. In severe TS, multimodal treatment, including administration of antithyroid drugs, KI, CSs and selective beta1 -AAs may be preferable to improve outcomes. © 2015 John Wiley & Sons Ltd.

ORACLE (Oversight of Resources and Capability for Logistics Effectiveness) and Requirements Forecasting. Volume 3. Predicting the Peacetime Spares Requirements.

DTIC Science & Technology

1988-05-01

Shearing Machines WR/MMI DG 3446 Forging Machinery and Hammers WR/MMI DG 3447 Wire and Metal Ribbon Forming Machines WR/MMI DG 3448 Riveting Machines ...R/MN1I DG 3449 Miscellaneous Secondary Metal Forming & Cutting WR/MMI DG Machinery 3450 Machine Tools, Portable WR/MMI DG 3455 Cutting Tools for...Secondary Metalworking Machinery WR/MMI DG WR 3465 Production Jigs, Fixtures and Templates WR/MMI DG WR 3470 Machine Shop Sets, Kits, and Outfits WR/MMI DG

Theory and simulation of multi-channel interference (MCI) widely tunable lasers.

PubMed

Chen, Quanan; Lu, Qiaoyin; Guo, Weihua

2015-07-13

A novel design of an InP-based monolithic widely tunable laser, multi-channel interference (MCI) laser, is proposed and presented for the first time. The device is comprised of a gain section, a common phase section and a multi-channel interference section. The multi-channel interference section contains a 1x8 splitter based on cascaded 1 × 2 multi-mode interferometers (MMIs) and eight arms with unequal length difference. The rear part of each arm is integrated with a one-port multi-mode interference reflector (MIR). Mode selection of the MCI laser is realized by the constructive interference of the lights reflected back by the eight arms. Through optimizing the arm length difference, a tuning range of more than 40 nm covering the whole C band, a threshold current around 11.5 mA and an side-mode-suppression-ratio (SMSR) up to 48 dB have been predicted for this widely tunable laser. Detailed design principle and numerical simulation results are presented.

The multiple mini-interview for emergency medicine resident selection.

PubMed

Hopson, Laura R; Burkhardt, John C; Stansfield, R Brent; Vohra, Taher; Turner-Lawrence, Danielle; Losman, Eve D

2014-04-01

The Multiple Mini-Interview (MMI) uses multiple, short-structured contacts to evaluate communication and professionalism. It predicts medical school success better than the traditional interview and application. Its acceptability and utility in emergency medicine (EM) residency selection are unknown. We theorized that participants would judge the MMI equal to a traditional unstructured interview and it would provide new information for candidate assessment. Seventy-one interns from 3 programs in the first month of training completed an eight-station MMI focused on EM topics. Pre- and post-surveys assessed reactions. MMI scores were compared with application data. EM grades correlated with MMI performance (F[1, 66] = 4.18; p < 0.05) with honors students having higher scores. Higher third-year clerkship grades were associated with higher MMI performance, although this was not statistically significant. MMI performance did not correlate with match desirability and did not predict most other components of an application. There was a correlation between lower MMI scores and lower global ranking on the Standardized Letter of Recommendation. Participants preferred a traditional interview (mean difference = 1.36; p < 0.01). A mixed format (traditional interview and MMI) was preferred over a MMI alone (mean difference = 1.1; p < 0.01). MMI performance did not significantly correlate with preference for the MMI. Although the MMI alone was viewed less favorably than a traditional interview, participants were receptive to a mixed-methods interview. The MMI does correlate with performance on the EM clerkship and therefore can measure important abilities for EM success. Future work will determine whether MMI performance predicts residency performance. Copyright © 2014 Elsevier Inc. All rights reserved.

All optical controlled photonic integrated circuits using azo dye functionized sol-gel material

NASA Astrophysics Data System (ADS)

Ke, Xianjun

The main focus of this dissertation is development and characterization of all-optical controllable azo dye functionized sol gel material, demonstrating a PIC fabrication technique on glass substrate using such material, and exploration and feasibility demonstration of three PIC functional devices namely optical variable attenuator, optical switches, and optical tunable filters using the material. The realization of all the devices in this dissertation are based on one material: dye functionalized sol-gel material. A photochromic sol-gel material functionalized with azo dye was synthesized and characterized. It possesses a photochromic characteristic under the control of green laser beam illumination. The material characteristics suggest the possibility of a new promising material platform candidate for the fabrication of alloptical controlled photonic integrated circuits. As the first potential application of the dye functionalized sol-gel material, an alloptical variable attenuator was designed and demonstrated. The optical variable attenuation is achieved in Mach-Zehnder interferometric configuration through all-optical modulation of sol-gel waveguide phase shifters. A 2 x 2 optical switch based on multimode interference (MMI) waveguide structure is proposed in the dissertation. The schematic configuration of the optical switch consists of a cascade of two identical MMIs with two all-optical controlled phase shifters realized by using the photochromic sol-gel material. The cross or bar switch state of the optical switch is determined by the phase difference between the two sol-gel waveguide phase shifters. An all-optical tunable filter is designed and its feasibility demonstrated by using the sol-gel photochromic material. Except for the phase change demonstrated on sol-gel waveguide phase shifters, dynamic gratings were observed on sol-gel film when exposed to two interference beams. This reveals the possibility of realizing Bragg grating-based tunable filters. The schematic configuration of proposed tunable filters consists of a single straight waveguide embedded with a sol-gel waveguide. The wavelength tuning of the tunable filters is accomplished by varying the grating period.

Interference of Multi-Mode Gaussian States and "non Appearance" of Quantum Correlations

NASA Astrophysics Data System (ADS)

Olivares, Stefano

2012-01-01

We theoretically investigate bilinear, mode-mixing interactions involving two modes of uncorrelated multi-mode Gaussian states. In particular, we introduce the notion of "locally the same states" (LSS) and prove that two uncorrelated LSS modes are invariant under the mode mixing, i.e. the interaction does not lead to the birth of correlations between the outgoing modes. We also study the interference of orthogonally polarized Gaussian states by means of an interferometric scheme based on a beam splitter, rotators of polarization and polarization filters.

Revisiting the contemporary sea-level budget on global and regional scales

PubMed Central

Brunnabend, Sandra-Esther; Kusche, Jürgen; Schröter, Jens; Dahle, Christoph

2016-01-01

Dividing the sea-level budget into contributions from ice sheets and glaciers, the water cycle, steric expansion, and crustal movement is challenging, especially on regional scales. Here, Gravity Recovery And Climate Experiment (GRACE) gravity observations and sea-level anomalies from altimetry are used in a joint inversion, ensuring a consistent decomposition of the global and regional sea-level rise budget. Over the years 2002–2014, we find a global mean steric trend of 1.38 ± 0.16 mm/y, compared with a total trend of 2.74 ± 0.58 mm/y. This is significantly larger than steric trends derived from in situ temperature/salinity profiles and models which range from 0.66 ± 0.2 to 0.94 ± 0.1 mm/y. Mass contributions from ice sheets and glaciers (1.37 ± 0.09 mm/y, accelerating with 0.03 ± 0.02 mm/y2) are offset by a negative hydrological component (−0.29 ± 0.26 mm/y). The combined mass rate (1.08 ± 0.3 mm/y) is smaller than previous GRACE estimates (up to 2 mm/y), but it is consistent with the sum of individual contributions (ice sheets, glaciers, and hydrology) found in literature. The altimetric sea-level budget is closed by coestimating a remaining component of 0.22 ± 0.26 mm/y. Well above average sea-level rise is found regionally near the Philippines (14.7 ± 4.39 mm/y) and Indonesia (8.3 ± 4.7 mm/y) which is dominated by steric components (11.2 ± 3.58 mm/y and 6.4 ± 3.18 mm/y, respectively). In contrast, in the central and Eastern part of the Pacific, negative steric trends (down to −2.8 ± 1.53 mm/y) are detected. Significant regional components are found, up to 5.3 ± 2.6 mm/y in the northwest Atlantic, which are likely due to ocean bottom pressure variations. PMID:26811469

Revisiting the contemporary sea-level budget on global and regional scales.

PubMed

Rietbroek, Roelof; Brunnabend, Sandra-Esther; Kusche, Jürgen; Schröter, Jens; Dahle, Christoph

2016-02-09

Dividing the sea-level budget into contributions from ice sheets and glaciers, the water cycle, steric expansion, and crustal movement is challenging, especially on regional scales. Here, Gravity Recovery And Climate Experiment (GRACE) gravity observations and sea-level anomalies from altimetry are used in a joint inversion, ensuring a consistent decomposition of the global and regional sea-level rise budget. Over the years 2002-2014, we find a global mean steric trend of 1.38 ± 0.16 mm/y, compared with a total trend of 2.74 ± 0.58 mm/y. This is significantly larger than steric trends derived from in situ temperature/salinity profiles and models which range from 0.66 ± 0.2 to 0.94 ± 0.1 mm/y. Mass contributions from ice sheets and glaciers (1.37 ± 0.09 mm/y, accelerating with 0.03 ± 0.02 mm/y(2)) are offset by a negative hydrological component (-0.29 ± 0.26 mm/y). The combined mass rate (1.08 ± 0.3 mm/y) is smaller than previous GRACE estimates (up to 2 mm/y), but it is consistent with the sum of individual contributions (ice sheets, glaciers, and hydrology) found in literature. The altimetric sea-level budget is closed by coestimating a remaining component of 0.22 ± 0.26 mm/y. Well above average sea-level rise is found regionally near the Philippines (14.7 ± 4.39 mm/y) and Indonesia (8.3 ± 4.7 mm/y) which is dominated by steric components (11.2 ± 3.58 mm/y and 6.4 ± 3.18 mm/y, respectively). In contrast, in the central and Eastern part of the Pacific, negative steric trends (down to -2.8 ± 1.53 mm/y) are detected. Significant regional components are found, up to 5.3 ± 2.6 mm/y in the northwest Atlantic, which are likely due to ocean bottom pressure variations.

Analysis of the rectangular resonator with butterfly MMI coupler using SOI

NASA Astrophysics Data System (ADS)

Kim, Sun-Ho; Park, Jun-Hee; Kim, Eudum; Jeon, Su-Jin; Kim, Ji-Hoon; Choi, Young-Wan

2018-02-01

We propose a rectangular resonator sensor structure with butterfly MMI coupler using SOI. It consists of the rectangular resonator, total internal reflection (TIR) mirror, and the butterfly MMI coupler. The rectangular resonator is expected to be used as bio and chemical sensors because of the advantages of using MMI coupler and the absence of bending loss unlike ring resonators. The butterfly MMI coupler can miniaturize the device compared to conventional MMI by using a linear butterfly shape instead of a square in the MMI part. The width, height, and slab height of the rib type waveguide are designed to be 1.5 μm, 1.5 μm, and 0.9 μm, respectively. This structure is designed as a single mode. When designing a TIR mirror, we considered the Goos-Hänchen shift and critical angle. We designed 3:1 MMI coupler because rectangular resonator has no bending loss. The width of MMI is designed to be 4.5 μm and we optimize the length of the butterfly MMI coupler using finite-difference time-domain (FDTD) method for higher Q-factor. It has the equal performance with conventional MMI even though the length is reduced by 1/3. As a result of the simulation, Qfactor of rectangular resonator can be obtained as 7381.

On the origin and removal of interference patterns in coated multimode fibres

NASA Astrophysics Data System (ADS)

Padilla Michel, Yazmin; Pulwer, Silvio; Saffari, Pouneh; Ksianzou, Viachaslau; Schrader, Sigurd

2016-07-01

In this study, we present the experimental investigations on interference patterns, such as those already reported in VIMOS-IFU, and up to now no appropriate explanation has been presented. These interference patterns are produced in multimode fibres coated with acrylate or polyimide, which is the preferred coating material for the fibres used in IFUs. Our experiments show that, under specific conditions, cladding modes interact with the coating and produce interference. Our results show that the conditions at which the fibre is held during data acquisition has an impact in the output spectrum. Altering the positioning conditions of the fibre leads to the changes into the interference pattern, therefore, fibres should be carefully manipulated in order to minimise this potential problem and improve the performance of these instruments. Finally we present a simple way of predicting and modelling this interference produced from the visible to the near infrared spectra. This model can be included in the data reduction pipeline in order to remove the interference patterns. These results should be of interest for the optimisation of the data reduction pipelines of instruments using optical fibres. Considering these results will benefit innovations and developments of high performance fibre systems.

Analysis of photonic spot profile converter and bridge structure on SOI platform for horizontal and vertical integration

NASA Astrophysics Data System (ADS)

Majumder, Saikat; Jha, Amit Kr.; Biswas, Aishik; Banerjee, Debasmita; Ganguly, Dipankar; Chakraborty, Rajib

2017-08-01

Horizontal spot size converter required for horizontal light coupling and vertical bridge structure required for vertical integration are designed on high index contrast SOI platform in order to form more compact integrated photonic circuits. Both the structures are based on the concept of multimode interference. The spot size converter can be realized by successive integration of multimode interference structures with reducing dimension on horizontal plane, whereas the optical bridge structure consists of a number of vertical multimode interference structure connected by single mode sections. The spot size converter can be modified to a spot profile converter when the final single mode waveguide is replaced by a slot waveguide. Analysis have shown that by using three multimode sections in a spot size converter, an Gaussian input having spot diameter of 2.51 μm can be converted to a spot diameter of 0.25 μm. If the output single mode section is replaced by a slot waveguide, this input profile can be converted to a flat top profile of width 50 nm. Similarly, vertical displacement of 8μm is possible by using a combination of two multimode sections and three single mode sections in the vertical bridge structure. The analyses of these two structures are carried out for both TE and TM modes at 1550 nm wavelength using the semi analytical matrix method which is simple and fast in computation time and memory. This work shows that the matrix method is equally applicable for analysis of horizontally as well as vertically integrated photonic circuit.

Potential teratogenicity of methimazole: exposure of zebrafish embryos to methimazole causes similar developmental anomalies to human methimazole embryopathy.

PubMed

Komoike, Yuta; Matsuoka, Masato; Kosaki, Kenjiro

2013-06-01

While methimazole (MMI) is widely used in the therapy for hyperthyroidism, several groups have reported that maternal exposure to MMI results in a variety of congenital anomalies, including choanal and esophageal atresia, iridic and retinal coloboma, and delayed neurodevelopment. Thus, adverse effects of maternal exposure to MMI on fetal development have long been suggested; however, direct evidence for the teratogenicity of MMI has not been presented. Therefore, we studied the effects of MMI on early development by using zebrafish as a model organism. The fertilized eggs of zebrafish were collected immediately after spawning and grown in egg culture water containing MMI at various concentrations. External observation of the embryos revealed that exposure to high concentrations of MMI resulted in loss of pigmentation, hypoplastic hindbrain, turbid tissue in the forebrain, swelling of the notochord, and curly trunk. Furthermore, these effects occurred in a dose-dependent manner. Precise observation of the serial cross-sections of MMI-exposed embryos elucidated delayed development and hypoplasia of the whole brain and spinal cord, narrowing of the pharynx and esophagus, severe disruption of the retina, and aberrant structure of the notochord. These neuronal, pharyngeal, esophageal, and retinal anomalous morphologies have a direct analogy to the congenital anomalies observed in children exposed to MMI in utero. Here, we show the teratogenic effects of MMI on the development of zebrafish and provide the first experimental evidence for the connection between exposure to MMI and human MMI embryopathy. © 2013 Wiley Periodicals, Inc.

Two-photon quantum walk in a multimode fiber

PubMed Central

Defienne, Hugo; Barbieri, Marco; Walmsley, Ian A.; Smith, Brian J.; Gigan, Sylvain

2016-01-01

Multiphoton propagation in connected structures—a quantum walk—offers the potential of simulating complex physical systems and provides a route to universal quantum computation. Increasing the complexity of quantum photonic networks where the walk occurs is essential for many applications. We implement a quantum walk of indistinguishable photon pairs in a multimode fiber supporting 380 modes. Using wavefront shaping, we control the propagation of the two-photon state through the fiber in which all modes are coupled. Excitation of arbitrary output modes of the system is realized by controlling classical and quantum interferences. This report demonstrates a highly multimode platform for multiphoton interference experiments and provides a powerful method to program a general high-dimensional multiport optical circuit. This work paves the way for the next generation of photonic devices for quantum simulation, computing, and communication. PMID:27152325

A Review of Multimode Interference in Tapered Optical Fibers and Related Applications.

PubMed

Wang, Pengfei; Zhao, Haiyan; Wang, Xianfan; Farrell, Gerald; Brambilla, Gilberto

2018-03-14

In recent years, tapered optical fibers (TOFs) have attracted increasing interest and developed into a range of devices used in many practical applications ranging from optical communication, sensing to optical manipulation and high-Q resonators. Compared with conventional optical fibers, TOFs possess a range of unique features, such as large evanescent field, strong optical confinement, mechanical flexibility and compactness. In this review, we critically summarize the multimode interference in TOFs and some of its applications with a focus on our research project undertaken at the Optoelectronics Research Centre of the University of Southampton in the United Kingdom.

A Review of Multimode Interference in Tapered Optical Fibers and Related Applications

PubMed Central

Wang, Pengfei; Zhao, Haiyan; Wang, Xianfan; Brambilla, Gilberto

2018-01-01

In recent years, tapered optical fibers (TOFs) have attracted increasing interest and developed into a range of devices used in many practical applications ranging from optical communication, sensing to optical manipulation and high-Q resonators. Compared with conventional optical fibers, TOFs possess a range of unique features, such as large evanescent field, strong optical confinement, mechanical flexibility and compactness. In this review, we critically summarize the multimode interference in TOFs and some of its applications with a focus on our research project undertaken at the Optoelectronics Research Centre of the University of Southampton in the United Kingdom. PMID:29538333

Mmi1, the Yeast Homologue of Mammalian TCTP, Associates with Stress Granules in Heat-Shocked Cells and Modulates Proteasome Activity

PubMed Central

Grousl, Tomas; Stradalova, Vendula; Heeren, Gino; Richter, Klaus; Breitenbach-Koller, Lore; Malinsky, Jan; Hasek, Jiri; Breitenbach, Michael

2013-01-01

As we have shown previously, yeast Mmi1 protein translocates from the cytoplasm to the outer surface of mitochondria when vegetatively growing yeast cells are exposed to oxidative stress. Here we analyzed the effect of heat stress on Mmi1 distribution. We performed domain analyses and found that binding of Mmi1 to mitochondria is mediated by its central alpha-helical domain (V-domain) under all conditions tested. In contrast, the isolated N-terminal flexible loop domain of the protein always displays nuclear localization. Using immunoelectron microscopy we confirmed re-location of Mmi1 to the nucleus and showed association of Mmi1 with intact and heat shock-altered mitochondria. We also show here that mmi1Δ mutant strains are resistant to robust heat shock with respect to clonogenicity of the cells. To elucidate this phenotype we found that the cytosolic Mmi1 holoprotein re-localized to the nucleus even in cells heat-shocked at 40°C. Upon robust heat shock at 46°C, Mmi1 partly co-localized with the proteasome marker Rpn1 in the nuclear region as well as with the cytoplasmic stress granules defined by Rpg1 (eIF3a). We co-localized Mmi1 also with Bre5, Ubp3 and Cdc48 which are involved in the protein de-ubiquitination machinery, protecting protein substrates from proteasomal degradation. A comparison of proteolytic activities of wild type and mmi1Δ cells revealed that Mmi1 appears to be an inhibitor of the proteasome. We conclude that one of the physiological functions of the multifunctional protein module, Mmi1, is likely in regulating degradation and/or protection of proteins thereby indirectly regulating the pathways leading to cell death in stressed cells. PMID:24204967

Prevention of relapse of Graves' disease by treatment with an intrathyroid injection of dexamethasone.

PubMed

Mao, Xiao-Ming; Li, Hui-Qin; Li, Qian; Li, Dong-Mei; Xie, Xiao-Jing; Yin, Guo-Ping; Zhang, Peng; Xu, Xiang-Hong; Wu, Jin-Dan; Chen, Song-Wang; Wang, Shu-Kui

2009-12-01

Antithyroid drugs are widely used in the treatment of Graves' disease (GD), but the relapse rate is very high after therapy withdrawal. We evaluated the reduction effects of intrathyroid injection of dexamethasone (IID) on the relapse rate of hyperthyroidism in patients with newly diagnosed GD. A total of 191 patients with GD completed the study. After 6 months of treatment with methimazole (MMI), the patients were randomly assigned to receive either MMI (96 patients) alone or MMI combined with IID (MMI+IID; 95 patients) treatment for 3 months, followed by continuing a dose of MMI that would maintain euthyroidism for the next 9 months in all of the patients. After withdrawal of the medical therapy, patients were followed for 24 months, and the relapse rate of hyperthyroidism was evaluated. No statistical difference was observed in the levels of serum FT(4), TSH, or TSH receptor antibodies (TR-Ab), the thyroid volume, or the TR-Ab positive rate between the two groups at month 6. After the next 3 months of treatment with MMI+IID or MMI alone, the levels of TSH increased significantly, and the levels of serum TR-Ab, the TR-Ab positive rate, and thyroid volume decreased significantly in the MMI+IID group compared with the MMI group. Seven patients (7.4%) experienced a relapse of overt hyperthyroidism in the MMI+IID group and 49 patients (51%) in MMI group during the 2-yr follow-up period (P < 0.001). MMI+IID treatment is helpful to prevent relapse of hyperthyroidism in GD after medical therapy withdrawal.

Design of photonic phased array switches using nano electromechanical systems on silicon-on-insulator integration platform

NASA Astrophysics Data System (ADS)

Hussein, Ali Abdulsattar

This thesis presents an introduction to the design and simulation of a novel class of integrated photonic phased array switch elements. The main objective is to use nano-electromechanical (NEMS) based phase shifters of cascaded under-etched slot nanowires that are compact in size and require a small amount of power to operate them. The structure of the switch elements is organized such that it brings the phase shifting elements to the exterior sides of the photonic circuits. The transition slot couplers, used to interconnect the phase shifters, are designed to enable biasing one of the silicon beams of each phase shifter from an electrode located at the side of the phase shifter. The other silicon beam of each phase shifter is biased through the rest of the silicon structure of the switch element, which is taken as a ground. Phased array switch elements ranging from 2x2 up to 8x8 multiple-inputs/multiple-outputs (MIMO) are conveniently designed within reasonable footprints native to the current fabrication technologies. Chapter one presents the general layout of the various designs of the switch elements and demonstrates their novel features. This demonstration will show how waveguide disturbances in the interconnecting network from conventional switch elements can be avoided by adopting an innovative design. Some possible applications for the designed switch elements of different sizes and topologies are indicated throughout the chapter. Chapter two presents the design of the multimode interference (MMI) couplers used in the switch elements as splitters, combiners and waveguide crossovers. Simulation data and design methodologies for the multimode couplers of interest are detailed in this chapter. Chapter three presents the design and analysis of the NEMS-operated phase shifters. Both simulations and numerical analysis are utilized in the design of a 0°-180° capable NEMS-operated phase shifter. Additionally, the response of some of the designed photonic phased array switch elements is demonstrated in this chapter. An executive summary and conclusions sections are also included in the thesis.

Anti-invasive and antiangiogenic effects of MMI-166 on malignant glioma cells

PubMed Central

2010-01-01

Background The constitutive overexpression of matrix metalloproteinases (MMPs) is frequently observed in malignant tumours. In particular, MMP-2 and MMP-9 have been reported to be closely associated with invasion and angiogenesis in malignant gliomas. Our study aimed to evaluate the antitumour effects of MMI-166 (Nalpha-[4-(2-Phenyl-2H- tetrazole-5-yl) phenyl sulfonyl]-D-tryptophan), a third generation MMP inhibitor, on three human glioma cell lines (T98G, U87MG, and ONS12) in vitro and in vivo. Methods The effects of MMI-166 on the gelatinolytic activity was analysed by gelatine zymography. The anti-invasive effect of MMI-166 was analysed by an in vitro invasion assay. An in vitro angiogenesis assay was also performed. In vitro growth inhibition of glioma cells by MMI-166 was determined by the MTT assay. The effect of MMI-166 on an orthotropic implantation model using athymic mice was also evaluated. Results Gelatine zymography revealed that MMP-2 and MMP-9 activities were suppressed by MMI-166. The invasion of glioma cells was suppressed by MMI-166. The angiogenesis assay showed that MMI-166 had a suppressive effect on glioma cell-induced angiogenesis. However, MMI-166 did not suppress glioma cell proliferation in the MTT assay. In vivo, MMI-166 suppressed tumour growth in athymic mice implanted orthotropically with T98G cells and showed an inhibitory effect on tumour-induced angiogenesis and tumour growth. This is the first report of the effect of a third generation MMP inhibitor on malignant glioma cells. Conclusions These results suggest that MMI-166 may have potentially suppressive effects on the invasion and angiogenesis of malignant gliomas. PMID:20587068

All-Fiber Laser Curvature Sensor Using an In-Fiber Modal Interferometer Based on a Double Clad Fiber and a Multimode Fiber Structure

PubMed Central

Durán-Sánchez, Manuel; Prieto-Cortés, Patricia; Salceda-Delgado, Guillermo; Castillo-Guzmán, Arturo A.; Selvas-Aguilar, Romeo; Ibarra-Escamilla, Baldemar; Kuzin, Evgeny A.

2017-01-01

An all-fiber curvature laser sensor by using a novel modal interference in-fiber structure is proposed and experimentally demonstrated. The in-fiber device, fabricated by fusion splicing of multimode fiber and double-clad fiber segments, is used as wavelength filter as well as the sensing element. By including a multimode fiber in an ordinary modal interference structure based on a double-clad fiber, the fringe visibility of the filter transmission spectrum is significantly increased. By using the modal interferometer as a curvature sensitive wavelength filter within a ring cavity erbium-doped fiber laser, the spectral quality factor Q is considerably increased. The results demonstrate the reliability of the proposed curvature laser sensor with advantages of robustness, ease of fabrication, low cost, repeatability on the fabrication process and simple operation. PMID:29182527

All-Fiber Laser Curvature Sensor Using an In-Fiber Modal Interferometer Based on a Double Clad Fiber and a Multimode Fiber Structure.

PubMed

Álvarez-Tamayo, Ricardo I; Durán-Sánchez, Manuel; Prieto-Cortés, Patricia; Salceda-Delgado, Guillermo; Castillo-Guzmán, Arturo A; Selvas-Aguilar, Romeo; Ibarra-Escamilla, Baldemar; Kuzin, Evgeny A

2017-11-28

An all-fiber curvature laser sensor by using a novel modal interference in-fiber structure is proposed and experimentally demonstrated. The in-fiber device, fabricated by fusion splicing of multimode fiber and double-clad fiber segments, is used as wavelength filter as well as the sensing element. By including a multimode fiber in an ordinary modal interference structure based on a double-clad fiber, the fringe visibility of the filter transmission spectrum is significantly increased. By using the modal interferometer as a curvature sensitive wavelength filter within a ring cavity erbium-doped fiber laser, the spectral quality factor Q is considerably increased. The results demonstrate the reliability of the proposed curvature laser sensor with advantages of robustness, ease of fabrication, low cost, repeatability on the fabrication process and simple operation.

Analysis of multimode fiber bundles for endoscopic spectral-domain optical coherence tomography

PubMed Central

Risi, Matthew D.; Makhlouf, Houssine; Rouse, Andrew R.; Gmitro, Arthur F.

2016-01-01

A theoretical analysis of the use of a fiber bundle in spectral-domain optical coherence tomography (OCT) systems is presented. The fiber bundle enables a flexible endoscopic design and provides fast, parallelized acquisition of the OCT data. However, the multimode characteristic of the fibers in the fiber bundle affects the depth sensitivity of the imaging system. A description of light interference in a multimode fiber is presented along with numerical simulations and experimental studies to illustrate the theoretical analysis. PMID:25967012

Unsupervised Domain Adaptation with Multiple Acoustic Models

DTIC Science & Technology

2010-12-01

Discriminative MAP Adaptation Standard ML-MAP has been extended to incorporate discrim- inative training criteria such as MMI and MPE [10]. Dis- criminative MAP...smoothing variable I . For example, the MMI - MAP mean is given by ( mmi -map) jm = fnumjm (O) den jm(O)g+Djm̂jm + I (ml-map) jm f numjm den... MMI training, and Djm is the Gaussian-dependent parameter for the extended Baum-Welch (EBW) algorithm. MMI -MAP has been successfully applied in

Joint Interference Alignment and Power Allocation for K-User Multicell MIMO Channel through Staggered Antenna Switching.

PubMed

Selvaprabhu, Poongundran; Chinnadurai, Sunil; Sarker, Md Abdul Latif; Lee, Moon Ho

2018-01-28

In this paper, we characterise the joint interference alignment (IA) and power allocation strategies for a K -user multicell multiple-input multiple-output (MIMO) Gaussian interference channel. We consider a MIMO interference channel with blind-IA through staggered antenna switching on the receiver. We explore the power allocation and feasibility condition for cooperative cell-edge (CE) mobile users (MUs) by assuming that the channel state information is unknown. The new insight behind the transmission strategy of the proposed scheme is premeditated (randomly generated transmission strategy) and partial cooperative CE MUs, where the transmitter is equipped with a conventional antenna, the receiver is equipped with a reconfigurable multimode antenna (staggered antenna switching pattern), and the receiver switches between preset T modes. Our proposed scheme assists and aligns the desired signals and interference signals to cancel the common interference signals because the received signal must have a corresponding independent signal subspace. The capacity for a K -user multicell MIMO Gaussian interference channel with reconfigurable multimode antennas is completely characterised. Furthermore, we show that the proposed K -user multicell MIMO scheduling and K -user L -cell CEUs partial cooperation algorithms elaborate the generalisation of K -user IA and power allocation strategies. The numerical results demonstrate that the proposed intercell interference scheme with partial-cooperative CE MUs achieves better capacity and signal-to-interference plus noise ratio (SINR) performance compared to noncooperative CE MUs and without intercell interference schemes.

Joint Interference Alignment and Power Allocation for K-User Multicell MIMO Channel through Staggered Antenna Switching

PubMed Central

2018-01-01

In this paper, we characterise the joint interference alignment (IA) and power allocation strategies for a K-user multicell multiple-input multiple-output (MIMO) Gaussian interference channel. We consider a MIMO interference channel with blind-IA through staggered antenna switching on the receiver. We explore the power allocation and feasibility condition for cooperative cell-edge (CE) mobile users (MUs) by assuming that the channel state information is unknown. The new insight behind the transmission strategy of the proposed scheme is premeditated (randomly generated transmission strategy) and partial cooperative CE MUs, where the transmitter is equipped with a conventional antenna, the receiver is equipped with a reconfigurable multimode antenna (staggered antenna switching pattern), and the receiver switches between preset T modes. Our proposed scheme assists and aligns the desired signals and interference signals to cancel the common interference signals because the received signal must have a corresponding independent signal subspace. The capacity for a K-user multicell MIMO Gaussian interference channel with reconfigurable multimode antennas is completely characterised. Furthermore, we show that the proposed K-user multicell MIMO scheduling and K-user L-cell CEUs partial cooperation algorithms elaborate the generalisation of K-user IA and power allocation strategies. The numerical results demonstrate that the proposed intercell interference scheme with partial-cooperative CE MUs achieves better capacity and signal-to-interference plus noise ratio (SINR) performance compared to noncooperative CE MUs and without intercell interference schemes. PMID:29382100

Augmented growth inhibition of B16-BL6 melanoma by combined treatment with a selective matrix metalloproteinase inhibitor, MMI-166, and cytotoxic agents.

PubMed

Hojo, Kanji; Maki, Hideo; Sawada, Takuko Yamada; Maekawa, Ryuji; Yoshioka, Takayuki

2002-01-01

MMI-166 is a selective matrix metalloproteinase (MMP) inhibitor. The purpose of this study was to evaluate the antitumor efficacy of the combined treatment of MMI-166 with paclitaxel or carboplatin. Mice bearing B16-BL6 melanoma were treated p.o. with MMI-166 from 1 day after tumor inoculation. The mice were administered i.v. with either paclitaxel or carboplatin at the maximum tolerated dose (MTD). MMI-166 monotherapy inhibited in vivo growth of the B16-BL6 tumor to an extent similar to that of paclitaxel or carboplatin monotherapy. When MMI-166 was combined with paclitaxel or carboplatin, the antitumor efficacy was significantly (p < 0.01) augmented in comparison with either MMI-166 or each cytotoxic agent alone. The hematotoxicity study demonstrated that daily treatment with MMI-166 did not affect the blood cell number in the mice and more importantly the combination of MMI-166 with paclitaxel did not augment the hematotoxicity caused by paclitaxel. An in vitro cytotoxicity study showed that MMI-166 itself has neither direct cytotoxicity against B16-BL6 tumor cells nor does it augment the cytotoxicity of paclitaxel or carboplatin. These results indicate that augmented antitumor activity of the combination treatment was not simply due to the augmentation of direct cytotoxic activity, but was rather an additive effect of the antitumor activities of different mechanisms. They suggest the effectiveness of a combination therapy of MMI-166 with paclitaxel or carboplatin in clinical therapy.

What does the multiple mini interview have to offer over the panel interview?

PubMed

Pau, Allan; Chen, Yu Sui; Lee, Verna Kar Mun; Sow, Chew Fei; De Alwis, Ranjit

2016-01-01

This paper compares the panel interview (PI) performance with the multiple mini interview (MMI) performance and indication of behavioural concerns of a sample of medical school applicants. The acceptability of the MMI was also assessed. All applicants shortlisted for a PI were invited to an MMI. Applicants attended a 30-min PI with two faculty interviewers followed by an MMI consisting of ten 8-min stations. Applicants were assessed on their performance at each MMI station by one faculty. The interviewer also indicated if they perceived the applicant to be a concern. Finally, applicants completed an acceptability questionnaire. From the analysis of 133 (75.1%) completed MMI scoresheets, the MMI scores correlated statistically significantly with the PI scores (r=0.438, p=0.001). Both were not statistically associated with sex, age, race, or pre-university academic ability to any significance. Applicants assessed as a concern at two or more stations performed statistically significantly less well at the MMI when compared with those who were assessed as a concern at one station or none at all. However, there was no association with PI performance. Acceptability scores were generally high, and comparison of mean scores for each of the acceptability questionnaire items did not show statistically significant differences between sex and race categories. Although PI and MMI performances are correlated, the MMI may have the added advantage of more objectively generating multiple impressions of the applicant's interpersonal skill, thoughtfulness, and general demeanour. Results of the present study indicated that the MMI is acceptable in a multicultural context.

What does the multiple mini interview have to offer over the panel interview?

PubMed Central

Pau, Allan; Chen, Yu Sui; Lee, Verna Kar Mun; Sow, Chew Fei; Alwis, Ranjit De

2016-01-01

Introduction This paper compares the panel interview (PI) performance with the multiple mini interview (MMI) performance and indication of behavioural concerns of a sample of medical school applicants. The acceptability of the MMI was also assessed. Materials and methods All applicants shortlisted for a PI were invited to an MMI. Applicants attended a 30-min PI with two faculty interviewers followed by an MMI consisting of ten 8-min stations. Applicants were assessed on their performance at each MMI station by one faculty. The interviewer also indicated if they perceived the applicant to be a concern. Finally, applicants completed an acceptability questionnaire. Results From the analysis of 133 (75.1%) completed MMI scoresheets, the MMI scores correlated statistically significantly with the PI scores (r=0.438, p=0.001). Both were not statistically associated with sex, age, race, or pre-university academic ability to any significance. Applicants assessed as a concern at two or more stations performed statistically significantly less well at the MMI when compared with those who were assessed as a concern at one station or none at all. However, there was no association with PI performance. Acceptability scores were generally high, and comparison of mean scores for each of the acceptability questionnaire items did not show statistically significant differences between sex and race categories. Conclusions Although PI and MMI performances are correlated, the MMI may have the added advantage of more objectively generating multiple impressions of the applicant's interpersonal skill, thoughtfulness, and general demeanour. Results of the present study indicated that the MMI is acceptable in a multicultural context. PMID:26873337

What does the multiple mini interview have to offer over the panel interview?

PubMed

Pau, Allan; Chen, Yu Sui; Lee, Verna Kar Mun; Sow, Chew Fei; Alwis, Ranjit De

2016-01-01

Introduction This paper compares the panel interview (PI) performance with the multiple mini interview (MMI) performance and indication of behavioural concerns of a sample of medical school applicants. The acceptability of the MMI was also assessed. Materials and methods All applicants shortlisted for a PI were invited to an MMI. Applicants attended a 30-min PI with two faculty interviewers followed by an MMI consisting of ten 8-min stations. Applicants were assessed on their performance at each MMI station by one faculty. The interviewer also indicated if they perceived the applicant to be a concern. Finally, applicants completed an acceptability questionnaire. Results From the analysis of 133 (75.1%) completed MMI scoresheets, the MMI scores correlated statistically significantly with the PI scores (r=0.438, p=0.001). Both were not statistically associated with sex, age, race, or pre-university academic ability to any significance. Applicants assessed as a concern at two or more stations performed statistically significantly less well at the MMI when compared with those who were assessed as a concern at one station or none at all. However, there was no association with PI performance. Acceptability scores were generally high, and comparison of mean scores for each of the acceptability questionnaire items did not show statistically significant differences between sex and race categories. Conclusions Although PI and MMI performances are correlated, the MMI may have the added advantage of more objectively generating multiple impressions of the applicant's interpersonal skill, thoughtfulness, and general demeanour. Results of the present study indicated that the MMI is acceptable in a multicultural context.

Perceptions and Cost-Analysis of a Multiple Mini-Interview in a Pharmacy School Admissions Process.

PubMed

Corelli, Robin L; Muchnik, Michael A; Beechinor, Ryan J; Fong, Gary; Vogt, Eleanor M; Cocohoba, Jennifer M; Tsourounis, Candy; Hudmon, Karen Suchanek

2015-11-25

To improve the quality of admissions interviews for a doctor of pharmacy program, using a multiple mini-interview (MMI) in place of the standard interview. Stakeholders completed an anonymous web-based survey. This study characterized perceptions of the MMI format across 3 major stakeholders (candidates, interviewers, admissions committee members) and included comparative cost estimates.Costs were estimated using human and facility resources from the 2012 cycle (standard format) and the 2013 cycle (MMI format). Most candidates (65%), interviewers (86%), and admissions committee members (79%) perceived the MMI format as effective for evaluating applicants, and most (59% of candidates, 84% of interviewers, 77% of committee members) agreed that the MMI format should be continued. Cost per candidate interviewed was $136.34 (standard interview) vs $75.30 (MMI). Perceptions of the MMI process were favorable across stakeholder groups, and this format was less costly per candidate interviewed.

Modified Mercalli Intensities (MMI) for some earthquakes in eastern North America (ENA) and empirical MMI site corrections for towns in ENA

USGS Publications Warehouse

Bakun, W.H.; Johnston, A.C.; Hopper, M.G.

2002-01-01

Modified Mercalli Intensity (MMI) assignments for earthquakes in eastern North America (ENA) were used by Bakun et al. (submitted) to develop a model for eastern North America for estimating the location and moment magnitude M of earthquakes from MMI observations. MMI assignments for most of the earthquakes considered by Bakun et al. (submitted) are published. MMI assignments for 6 other earthquakes used by Bakun et al. (submitted) are listed in this report: November 18, 1755 near Cape Ann, Massachusetts; January 5, 1843 near Marked Tree, Arkansas; October 31, 1895 in southern Illinois; November 18, 1929 on the Grand Banks, Newfoundland; September 26, 1990 in southeast Missouri; and May 4, 1991 near Risco, Missouri. MMI empirical site corrections developed and used by Bakun et al. (submitted) are also listed in this report.

Development and Assessment of the Multiple Mini-Interview in a School of Pharmacy Admissions Model

PubMed Central

McLaughlin, Jacqueline E.; Singer, David; Lewis, Margaret; Dinkins, Melissa M.

2015-01-01

Objective. To describe the development, implementation, and evaluation of the multiple mini-interview (MMI) within a doctor of pharmacy (PharmD) admissions model. Methods. Demographic data and academic indicators were collected for all candidates who participated in Candidates’ Day (n=253), along with the score for each MMI station criteria (7 stations). A survey was administered to all candidates who completed the MMI, and another survey was administered to all interviewers to examine perceptions of the MMI. Results. Analyses suggest that MMI stations assessed different attributes as designed, with Cronbach alpha for each station ranging from 0.90 to 0.95. All correlations between MMI station scores and academic indicators were negligible. No significant differences in average station scores were found based on age, gender, or race. Conclusion. This study provides additional support for the use of the MMI as an admissions tool in pharmacy education. PMID:26089562

Maternal transfer of methimazole and effects on thyroid hormone availability in embryonic tissues.

PubMed

Van Herck, Stijn L J; Geysens, Stijn; Bald, Edward; Chwatko, Grazyna; Delezie, Evelyne; Dianati, Elham; Ahmed, R G; Darras, Veerle M

2013-07-01

Methimazole (MMI) is an anti-thyroid drug used in the treatment of chronic hyperthyroidism. There is, however, some debate about its use during pregnancy as MMI is known to cross the mammalian placenta and reach the developing foetus. A similar problem occurs in birds, where MMI is deposited in the egg and taken up by the developing embryo. To investigate whether maternally derived MMI can have detrimental effects on embryonic development, we treated laying hens with MMI (0.03% in drinking water) and measured total and reduced MMI contents in the tissues of hens and embryos at different stages of development. In hens, MMI was selectively increased in the thyroid gland, while its levels in the liver and especially brain remained relatively low. Long-term MMI treatment induced a pronounced goitre with a decrease in thyroxine (T₄) content but an increase in thyroidal 3,5,3'-triiodothyronine (T₃) content. This resulted in normal T₃ levels in tissues except in the brain. In chicken embryos, MMI levels were similar in the liver and brain. They gradually decreased during development but always remained above those in the corresponding maternal tissues. Contrary to the situation in hens, T₄ availability was only moderately affected in embryos. Peripheral T₃ levels were reduced in 14-day-old embryos but normal in 18-day-old embryos, while brain T₃ content was decreased at all embryonic stages tested. We conclude that all embryonic tissues are exposed to relatively high doses of MMI and its oxidised metabolites. The effect of maternal MMI treatment on embryonic thyroid hormone availability is most pronounced for brain T₃ content, which is reduced throughout the embryonic development period.

Quantum interference of independently generated telecom-band single photons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Patel, Monika; Altepeter, Joseph B.; Huang, Yu-Ping

We report on high-visibility quantum interference of independently generated telecom O-band (1310 nm) single photons using standard single-mode fibers. The experimental data are shown to agree well with the results of simulations using a comprehensive quantum multimode theory without the need for any fitting parameter.

Quantum interference between transverse spatial waveguide modes.

PubMed

Mohanty, Aseema; Zhang, Mian; Dutt, Avik; Ramelow, Sven; Nussenzveig, Paulo; Lipson, Michal

2017-01-20

Integrated quantum optics has the potential to markedly reduce the footprint and resource requirements of quantum information processing systems, but its practical implementation demands broader utilization of the available degrees of freedom within the optical field. To date, integrated photonic quantum systems have primarily relied on path encoding. However, in the classical regime, the transverse spatial modes of a multi-mode waveguide have been easily manipulated using the waveguide geometry to densely encode information. Here, we demonstrate quantum interference between the transverse spatial modes within a single multi-mode waveguide using quantum circuit-building blocks. This work shows that spatial modes can be controlled to an unprecedented level and have the potential to enable practical and robust quantum information processing.

Wavelength tuning of multimode interference bandpass filters by mechanical bending: experiment and theory in comparison

NASA Astrophysics Data System (ADS)

Walbaum, T.; Fallnich, C.

2012-07-01

We present the tuning of multimode interference bandpass filters made of standard fibers by mechanical bending. Our setup allows continuous adjustment of the bending radius from infinity down to about 5 cm. The impact of bending on the transmission spectrum and on polarization is investigated experimentally, and a filter with a continuous tuning range of 13.6 nm and 86 % peak transmission was realized. By use of numerical simulations employing a semi-analytical mode expansion approach, we obtain quantitative understanding of the underlying physics. Further breakdown of the governing equations enables us to identify the fiber parameters that are relevant for the design of customized filters.

White matter damage and glymphatic dysfunction in a model of vascular dementia in rats with no prior vascular pathologies

PubMed Central

Venkat, Poornima; Chopp, Michael; Zacharek, Alex; Cui, Chengcheng; Zhang, Li; Li, Qingjiang; Lu, Mei; Zhang, Talan; Liu, Amy; Chen, Jieli

2016-01-01

We investigated cognitive function, axonal/white matter (WM) changes and glymphatic function of vascular dementia (VaD) using a multiple microinfarction (MMI) model in retired breeder (RB) rats. The MMI model induces significant (p<0.05) cognitive decline that worsens with age starting at 2 weeks, which persists until at least 6 weeks after MMI. RB rats subjected to MMI exhibit significant axonal/WM damage identified by decreased myelin thickness, oligodendrocyte progenitor cell numbers, axon density, synaptic protein expression in the cortex and striatum, cortical neuronal branching, and dendritic spine density in the cortex and hippocampus compared with age matched controls. MMI evokes significant dilation of perivascular spaces as well as water channel dysfunction indicated by decreased Aquaporin-4 (AQP-4) expression around blood vessels. MMI induced glymphatic dysfunction with delayed cerebrospinal fluid (CSF) penetration into the brain parenchyma via paravascular pathways as well as delayed waste clearance from the brain. The MMI model in RB rats decreases AQP-4 and induces glymphatic dysfunction which may play an important role in MMI induced axonal/WM damage and cognitive deficits. PMID:27940353

White matter damage and glymphatic dysfunction in a model of vascular dementia in rats with no prior vascular pathologies.

PubMed

Venkat, Poornima; Chopp, Michael; Zacharek, Alex; Cui, Chengcheng; Zhang, Li; Li, Qingjiang; Lu, Mei; Zhang, Talan; Liu, Amy; Chen, Jieli

2017-02-01

We investigated cognitive function, axonal/white matter (WM) changes and glymphatic function of vascular dementia using a multiple microinfarction (MMI) model in retired breeder (RB) rats. The MMI model induces significant (p < 0.05) cognitive decline that worsens with age starting at 2 weeks, which persists until at least 6 weeks after MMI. RB rats subjected to MMI exhibit significant axonal/WM damage identified by decreased myelin thickness, oligodendrocyte progenitor cell numbers, axon density, synaptic protein expression in the cortex and striatum, cortical neuronal branching, and dendritic spine density in the cortex and hippocampus compared with age-matched controls. MMI evokes significant dilation of perivascular spaces as well as water channel dysfunction indicated by decreased Aquaporin-4 expression around blood vessels. MMI-induced glymphatic dysfunction with delayed cerebrospinal fluid penetration into the brain parenchyma via paravascular pathways as well as delayed waste clearance from the brain. The MMI model in RB rats decreases Aquaporin-4 and induces glymphatic dysfunction which may play an important role in MMI-induced axonal/WM damage and cognitive deficits. Copyright © 2016 Elsevier Inc. All rights reserved.

Evaluating the MMI diagnostic on OMEGA direct-drive shots

NASA Astrophysics Data System (ADS)

Baumgaertel, J. A.; Bradley, P. A.; Cobble, J. A.; Fincke, J.; Hakel, P.; Hsu, S. C.; Kanzleiter, R.; Krasheninnikova, N. S.; Murphy, T. J.; Schmitt, M. J.; Shah, R.; Tregillis, I.; Obrey, K.; Mancini, R. C.; Joshi, T.; Johns, H.; Mayes, D.

2013-10-01

The Defect-Induced Mix Experiment (DIME) project utilized Multiple Monochromatic Imagers (MMI) on symmetric and polar direct-drive shots conducted on the OMEGA laser. The MMI provides spatially and spectrally resolved data of capsule implosions and resultant dopant emissions. The capsules had radii of 430 μm, with CH shells that included an inner layer doped with 1-2 atom % Ti, and a gas fill of 5 atm deuterium. Simulations of the target implosion by codes HYDRA and RAGE are post-processed with self-emission and MMI synthetic diagnostic tools and quantitatively compared to the MMI data to determine the utility of using it for mix model validation. MMI data shows the location of dopants, which are used to diagnose mix. Sensitivities of synthetic MMI images and yield to laser drive and mix levels are explored. Finally, RAGE results, clean and with mix, are compared with time-dependent streak camera data. This work is supported by US DOE/NNSA, performed at LANL, operated by LANS LLC under contract DE-AC52-06NA25396.

Hypothyroidism during antithyroid drug treatment with methimazole is a favorable prognostic indicator in patients with Graves' disease.

PubMed

Choo, Young Kwang; Yoo, Won Sang; Kim, Dong Woo; Chung, Hyun-Kyung

2010-09-01

A major problem with antithyroid drug (ATD) therapy in Graves' disease is the high relapse rate. Therefore, clinicians have sought prognostic indicators of permanent remission. Suppression of serum thyrotropin (TSH) when ATD therapy is stopped carries a poor prognosis, but little is known regarding the significance of elevated serum TSH concentrations in the course of ATD therapy. The objective of this study was to determine if elevated serum TSH concentrations during methimazole (MMI) therapy is associated with a favorable long-term prognosis. We retrospectively studied patients with Graves' disease who were initially on MMI, in whom this drug was stopped because they had undetectable thyroid-stimulating antibodies (TSAbs) or were euthyroid after at least 24 months on MMI treatment. A strategy of high MMI doses plus T4 was not used in these patients. We identified 40 patients with elevated serum TSH concentration (>10 microIU/mL) during MMI therapy (H-TSH group). Eighty-five percent of the H-TSH group had negative tests for TSAb. The H-TSH group was sex- and age-matched with 37 patients who had similar selection criteria, but did not have elevated serum TSH concentration during MMI therapy (N-TSH group). The H-TSH and N-TSH groups were similar in gross thyroid size, percentage of patients with exophthalmos, serum free thyroxine, duration of MMI treatment, TSAb status, duration that their TSAb tests remained negative, and thyroid peroxidase antibody titers. The patients were followed for 24 months after stopping MMI. In the H-TSH group, MMI-associated hypothyroidism typically occurred after 7-8 months of treatment with daily doses of 10-15 mg MMI. No patient had severe symptoms of hypothyroidism. The percentage of patients in remission at 6, 12, and 24 months after discontinuation of MMI was 90.0, 87.5, and 85.0, respectively, in the H-TSH group and 70.3, 67.6, and 54.1, respectively, in the N-TSH group (p  <  0.05 for the comparison of groups at 6 and 12 months and p  <  0.001 for comparison of the groups at 24 months). In patients with Graves' disease who are treated with MMI for at least 2 years and become euthyroid, the occurrence of elevated serum TSH concentrations during MMI treatment is a favorable indicator for long-term remission and is independent of multiple other factors including TSAb status, duration of MMI treatment, and gross parameters of goiter size.

Fiber-based three-dimensional multi-mode interference device as efficient power divider and vector curvature sensor

NASA Astrophysics Data System (ADS)

Zhang, Ziyang; Fiebrandt, Julia; Haynes, Dionne; Sun, Kai; Madhav, Kalaga; Stoll, Andreas; Makan, Kirill; Makan, Vadim; Roth, Martin

2018-03-01

Three-dimensional multi-mode interference devices are demonstrated using a single-mode fiber (SMF) center-spliced to a section of polygon-shaped core multimode fiber (MMF). This simple structure can effectively generate well-localized self-focusing spots that match to the layout of a chosen multi-core fiber (MCF) as a launcher device. An optimized hexagon-core MMF can provide efficient coupling from a SMF to a 7-core MCF with an insertion loss of 0.6 dB and a power imbalance of 0.5 dB, while a square-core MMF can form a self-imaging pattern with symmetrically distributed 2 × 2, 3 × 3 or 4 × 4 spots. These spots can be directly received by a two-dimensional detector array. The device can work as a vector curvature sensor by comparing the relative power among the spots with a resolution of ∼0.1° over a 1.8 mm-long MMF.

Modified mercalli intensities for nine earthquakes in central and western Washington between 1989 and 1999

USGS Publications Warehouse

Brocher, Thomas M.; Dewey, James W.; Cassidy, John F.

2017-08-15

We determine Modified Mercalli (Seismic) Intensities (MMI) for nine onshore earthquakes of magnitude 4.5 and larger that occurred in central and western Washington between 1989 and 1999, on the basis of effects reported in postal questionnaires, the press, and professional collaborators. The earthquakes studied include four earthquakes of M5 and larger: the M5.0 Deming earthquake of April 13, 1990, the M5.0 Point Robinson earthquake of January 29, 1995, the M5.4 Duvall earthquake of May 3, 1996, and the M5.8 Satsop earthquake of July 3, 1999. The MMI are assigned using data and procedures that evolved at the U.S. Geological Survey (USGS) and its Department of Commerce predecessors and that were used to assign MMI to felt earthquakes occurring in the United States between 1931 and 1986. We refer to the MMI assigned in this report as traditional MMI, because they are based on responses to postal questionnaires and on newspaper reports, and to distinguish them from MMI calculated from data contributed by the public by way of the internet. Maximum traditional MMI documented for the M5 and larger earthquakes are VII for the 1990 Deming earthquake, V for the 1995 Point Robinson earthquake, VI for the 1996 Duvall earthquake, and VII for the 1999 Satsop earthquake; the five other earthquakes were variously assigned maximum intensities of IV, V, or VI. Starting in 1995, the Pacific Northwest Seismic Network (PNSN) published MMI maps for four of the studied earthquakes, based on macroseismic observations submitted by the public by way of the internet. With the availability now of the traditional USGS MMI interpreted for all the sites from which USGS postal questionnaires were returned, the four Washington earthquakes join a rather small group of earthquakes for which both traditional USGS MMI and some type of internet-based MMI have been assigned. The values and distributions of the traditional MMI are broadly similar to the internet-based PNSN intensities; we discuss some differences in detail that reflect differences in data-sampling procedure, differences in the procedure used to assign intensity numbers from macroseismic observations, and differences in how intensities are mapped.

Qualitative analysis of MMI raters' scorings of medical school candidates: A matter of taste?

PubMed

Christensen, Mette K; Lykkegaard, Eva; Lund, Ole; O'Neill, Lotte D

2018-05-01

Recent years have seen leading medical educationalists repeatedly call for a paradigm shift in the way we view, value and use subjectivity in assessment. The argument is that subjective expert raters generally bring desired quality, not just noise, to performance evaluations. While several reviews document the psychometric qualities of the Multiple Mini-Interview (MMI), we currently lack qualitative studies examining what we can learn from MMI raters' subjectivity. The present qualitative study therefore investigates rater subjectivity or taste in MMI selection interview. Taste (Bourdieu 1984) is a practical sense, which makes it possible at a pre-reflective level to apply 'invisible' or 'tacit' categories of perception for distinguishing between good and bad. The study draws on data from explorative in-depth interviews with 12 purposefully selected MMI raters. We find that MMI raters spontaneously applied subjective criteria-their taste-enabling them to assess the candidates' interpersonal attributes and to predict the candidates' potential. In addition, MMI raters seemed to share a taste for certain qualities in the candidates (e.g. reflectivity, resilience, empathy, contact, alikeness, 'the good colleague'); hence, taste may be the result of an ongoing enculturation in medical education and healthcare systems. This study suggests that taste is an inevitable condition in the assessment of students' performance. The MMI set-up should therefore make room for MMI raters' taste and their connoisseurship, i.e. their ability to taste, to improve the quality of their assessment of medical school candidates.

On-chip particle trapping and manipulation

NASA Astrophysics Data System (ADS)

Leake, Kaelyn Danielle

The ability to control and manipulate the world around us is human nature. Humans and our ancestors have used tools for millions of years. Only in recent years have we been able to control objects at such small levels. In order to understand the world around us it is frequently necessary to interact with the biological world. Optical trapping and manipulation offer a non-invasive way to move, sort and interact with particles and cells to see how they react to the world around them. Optical tweezers are ideal in their abilities but they require large, non-portable, and expensive setups limiting how and where we can use them. A cheap portable platform is required in order to have optical manipulation reach its full potential. On-chip technology offers a great solution to this challenge. We focused on the Liquid-Core Anti-Resonant Reflecting Optical Waveguide (liquid-core ARROW) for our work. The ARROW is an ideal platform, which has anti-resonant layers which allow light to be guided in liquids, allowing for particles to easily be manipulated. It is manufactured using standard silicon manufacturing techniques making it easy to produce. The planner design makes it easy to integrate with other technologies. Initially I worked to improve the ARROW chip by reducing the intersection losses and by reducing the fluorescence and background on the ARROW chip. The ARROW chip has already been used to trap and push particles along its channel but here I introduce several new methods of particle trapping and manipulation on the ARROW chip. Traditional two beam traps use two counter propagating beams. A trapping scheme that uses two orthogonal beams which counter to first instinct allow for trapping at their intersection is introduced. This scheme is thoroughly predicted and analyzed using realistic conditions. Simulations of this method were done using a program which looks at both the fluidics and optical sources to model complex situations. These simulations were also used to model and predict a sorting method which combines fluid flow with a single optical source to automatically sort dielectric particles by size in waveguide networks. These simulations were shown to be accurate when repeated on-chip. Lastly I introduce a particle trapping technique that uses Multimode Interference(MMI) patterns in order to trap multiple particles at once. The location of the traps can be adjusted as can the number of trapping location by changing the input wavelength. By changing the wavelength back and forth between two values this MMI can be used to pass a particle down the channel like a conveyor belt.

Relationship between dose of antithyroid drugs and adverse events in pediatric patients with Graves’ disease

PubMed Central

Yasuda, Kie; Miyoshi, Yoko; Tachibana, Makiko; Namba, Noriyuki; Miki, Kazunori; Nakata, Yukiko; Takano, Toru; Ozono, Keiichi

2017-01-01

Abstract. Graves’ disease (GD) accounts for a large proportion of pediatric hyperthyroidism, and the first-line treatment is antithyroid drug (ATD) therapy. Methimazole (MMI) is effective in most patients but is associated with significant adverse events (AEs). We reviewed the medical records of GD patients (n = 56) with onset age of <15 yr and investigated the relationship between MMI dose and AEs. The study population comprised 11 male and 45 female patients and the median age at diagnosis was 11 yr. All patients were initially treated with ATDs. Among the 52 patients initially treated with MMI, 20 received a low dose, and 32 received a high dose of MMI (< 0.7 vs ≥ 0.7 mg/kg/day, respectively). AEs occurred in 20% of the patients in the low-dose MMI group, and in 50% patients in the high-dose MMI group (p = 0.031). A greater variety of AEs was observed in the high-dose group. Neutropenia and rash were observed in both groups. With treatment transition to low-dose MMI according to the Japanese Society for Pediatric Endocrinology guidelines, we expect a decrease in the incidence of AEs in future. However, we should be careful as neutropenia and rash can occur independently of the MMI dose. PMID:28203042

Relationship between dose of antithyroid drugs and adverse events in pediatric patients with Graves' disease.

PubMed

Yasuda, Kie; Miyoshi, Yoko; Tachibana, Makiko; Namba, Noriyuki; Miki, Kazunori; Nakata, Yukiko; Takano, Toru; Ozono, Keiichi

2017-01-01

Graves' disease (GD) accounts for a large proportion of pediatric hyperthyroidism, and the first-line treatment is antithyroid drug (ATD) therapy. Methimazole (MMI) is effective in most patients but is associated with significant adverse events (AEs). We reviewed the medical records of GD patients (n = 56) with onset age of <15 yr and investigated the relationship between MMI dose and AEs. The study population comprised 11 male and 45 female patients and the median age at diagnosis was 11 yr. All patients were initially treated with ATDs. Among the 52 patients initially treated with MMI, 20 received a low dose, and 32 received a high dose of MMI (< 0.7 vs ≥ 0.7 mg/kg/day, respectively). AEs occurred in 20% of the patients in the low-dose MMI group, and in 50% patients in the high-dose MMI group (p = 0.031). A greater variety of AEs was observed in the high-dose group. Neutropenia and rash were observed in both groups. With treatment transition to low-dose MMI according to the Japanese Society for Pediatric Endocrinology guidelines, we expect a decrease in the incidence of AEs in future. However, we should be careful as neutropenia and rash can occur independently of the MMI dose.

Multiple Monochromatic Imaging (MMI) Status and Plans for LANL Campaigns on Omega and NIF

NASA Astrophysics Data System (ADS)

Wysocki, F. J.; Hsu, S. C.; Tregillis, I. L.; Schmitt, M. J.; Kyrala, G. A.; Martinson, D. D.; Murphy, T. J.; Mancini, R. C.; Nagayama, T.

2011-10-01

LANL's DIME (Defect Implosion Experiment) campaigns on Omega and NIF are aimed at obtaining improved understanding of defect-induced mix via experiments and simulations of directly driven high-Z doped plastic capsules with DD or DT gas fill. To this end, the MMI diagnostic has been identified as a key diagnostic for providing space and time-resolved density, temperature, and mix profiles. The high Z shell dopants used on Omega are Ti and V, and to be used on NIF are Ge and Se. This poster will discuss the following four areas of MMI-related work at LANL, in collaboration with UNR: (1) data and preliminary analysis of MMI data from FY11 Omega campaigns, (2) development of a capability to generate simulated MMI data from radiation- hydrodynamic simulations of ICF implosions, (3) design of an MMI instrument for NIF that will cover the photon energy range 9.5-16.9 keV which includes the Ge/Se, H- like/He-like, α/ β lines, and (4) the development of MMI data post- processing and spectroscopic analysis tools. Supported by DOE NNSA.

Detection of elemental mercury by multimode diode laser correlation spectroscopy.

PubMed

Lou, Xiutao; Somesfalean, Gabriel; Svanberg, Sune; Zhang, Zhiguo; Wu, Shaohua

2012-02-27

We demonstrate a method for elemental mercury detection based on correlation spectroscopy employing UV laser radiation generated by sum-frequency mixing of two visible multimode diode lasers. Resonance matching of the multimode UV laser is achieved in a wide wavelength range and with good tolerance for various operating conditions. Large mode-hops provide an off-resonance baseline, eliminating interferences from other gas species with broadband absorption. A sensitivity of 1 μg/m3 is obtained for a 1-m path length and 30-s integration time. The performance of the system shows promise for mercury monitoring in industrial applications.

Comparison of the multiple mini-interview with the traditional interview for U.S. emergency medicine residency applicants: a single-institution experience.

PubMed

Soares, William E; Sohoni, Aparajita; Hern, Herbert G; Wills, Charlotte P; Alter, Harrison J; Simon, Barry C

2015-01-01

The multiple mini-interview (MMI) is a validated interview technique used primarily to evaluate medical school applicants. No study has compared MMIs with traditional interviews (TIs) in the evaluation of U.S. emergency medicine residency (EMR) applicants. During the 2011-2012 interview season, a four-station MMI was incorporated into the interview process for EMR applicants at Alameda Health System-Highland Hospital (AHS). A postinterview anonymous questionnaire was offered to all applicants after they submitted their rank lists but prior to release of National Residency Matching Program results. Respondents rated their perceptions of the MMI and TI on a five-point Likert scale. McNemar chi-square test was used to explore differences in respondents' perceptions of interview styles. One hundred ten interviewees completed the survey (73%). Overall, applicants found the TI more enjoyable than the MMI process (98 [89%] compared with 48 [44%], McNemar chi-square=28.66, P<.01) and preferred the TI process to the MMI (66 [60%] compared with 9 [10%], McNemar chi-square=40.81, P<.01). Sixteen applicants (14%) indicated that the use of the MMI would negatively affect their ranking of the program. In contrast to prior studies, U.S. EMR applicants to AHS preferred the TI to the MMI. Further investigation into the use of the MMI for selecting U.S. EMR applicants is warranted.

The validity of a behavioural multiple-mini-interview within an assessment centre for selection into specialty training

PubMed Central

2014-01-01

Background Entry into specialty training was determined by a National Assessment Centre (NAC) approach using a combination of a behavioural Multiple-Mini-Interview (MMI) and a written Situational Judgement Test (SJT). We wanted to know if interviewers could make reliable and valid decisions about the non-cognitive characteristics of candidates with the purpose of selecting them into general practice specialty training using the MMI. Second, we explored the concurrent validity of the MMI with the SJT. Methods A variance components analysis estimated the reliability and sources of measurement error. Further modelling estimated the optimal configurations for future MMI iterations. We calculated the relationship of the MMI with the SJT. Results Data were available from 1382 candidates, 254 interviewers, six MMI questions, five alternate forms of a 50-item SJT, and 11 assessment centres. For a single MMI question and one assessor, 28% of the variance between scores was due to candidate-to-candidate variation. Interviewer subjectivity, in particular the varying views that interviewer had for particular candidates accounted for 40% of the variance in scores. The generalisability co-efficient for a six question MMI was 0.7; to achieve 0.8 would require ten questions. A disattenuated correlation with the SJT (r = 0.35), and in particular a raw score correlation with the subdomain related to clinical knowledge (r = 0.25) demonstrated evidence for construct and concurrent validity. Less than two per cent of candidates would have failed the MMI. Conclusion The MMI is a moderately reliable method of assessment in the context of a National Assessment Centre approach. The largest source of error relates to aspects of interviewer subjectivity, suggesting enhanced interviewer training would be beneficial. MMIs need to be sufficiently long for precise comparison for ranking purposes. In order to justify long term sustainable use of the MMI in a postgraduate assessment centre approach, more theoretical work is required to understand how written and performance based test of non-cognitive attributes can be combined, in a way that achieves acceptable generalizability, and has validity. PMID:25123968

Hypothyroidism Enhanced Ectonucleotidases and Acetylcholinesterase Activities in Rat Synaptosomes can be Prevented by the Naturally Occurring Polyphenol Quercetin.

PubMed

Baldissarelli, Jucimara; Santi, Adriana; Schmatz, Roberta; Abdalla, Fátima Husein; Cardoso, Andréia Machado; Martins, Caroline Curry; Dias, Glaecir R Mundstock; Calgaroto, Nicéia Spanholi; Pelinson, Luana Paula; Reichert, Karine Paula; Loro, Vania Lucia; Morsch, Vera Maria Melchiors; Schetinger, Maria Rosa Chitolina

2017-01-01

Thyroid hormones have an influence on the functioning of the central nervous system. Furthermore, the cholinergic and purinergic systems also are extensively involved in brain function. In this context, quercetin is a polyphenol with antioxidant and neuroprotective properties. This study investigated the effects of (MMI)-induced hypothyroidism on the NTPDase, 5'-nucleotidase, adenosine deaminase (ADA), and acetylcholinesterase (AChE) activities in synaptosomes of rats and whether the quercetin can prevent it. MMI at a concentration of 20 mg/100 mL was administered for 90 days in the drinking water. The animals were divided into six groups: control/water (CT/W), control/quercetin 10 mg/kg, control/quercetin 25 mg/kg, methimazole/water (MMI/W), methimazole/quercetin 10 mg/kg (MMI/Q10), and methimazole/quercetin 25 mg/kg (MMI/Q25). On the 30th day, hormonal dosing was performed to confirm hypothyroidism, and the animals were subsequently treated with 10 or 25 mg/kg quercetin for 60 days. NTPDase activity was not altered in the MMI/W group. However, treatment with quercetin decreased ATP and ADP hydrolysis in the MMI/Q10 and MMI/Q25 groups. 5'-nucleotidase activity increased in the MMI/W group, but treatments with 10 or 25 mg/kg quercetin decreased 5'-nucleotidase activity. ADA activity decreased in the CT/25 and MMI/Q25 groups. Furthermore, AChE activity was reduced in all groups with hypothyroidism. In vitro tests also demonstrated that quercetin per se decreased NTPDase, 5'-nucleotidase, and AChE activities. This study demonstrated changes in the 5'-nucleotidase and AChE activities indicating that purinergic and cholinergic neurotransmission are altered in this condition. In addition, quercetin can alter these parameters and may be a promising natural compound with important neuroprotective actions in hypothyroidism.

MMI attenuation and historical earthquakes in the basin and range province of western North America

USGS Publications Warehouse

Bakun, W.H.

2006-01-01

Earthquakes in central Nevada (1932-1959) were used to develop a modified Mercalli intensity (MMI) attenuation model for estimating moment magnitude M for earthquakes in the Basin and Range province of interior western North America. M is 7.4-7.5 for the 26 March 1872 Owens Valley, California, earthquake, in agreement with Beanland and Clark's (1994) M 7.6 that was estimated from geologic field observations. M is 7.5 for the 3 May 1887 Sonora, Mexico, earthquake, in agreement with Natali and Sbar's (1982) M 7.4 and Suter's (2006) M 7.5, both estimated from geologic field observations. MMI at sites in California for earthquakes in the Nevada Basin and Range apparently are not much affected by the Sierra Nevada except at sites near the Sierra Nevada where MMI is reduced. This reduction in MMI is consistent with a shadow zone produced by the root of the Sierra Nevada. In contrast, MMI assignments for earthquakes located in the eastern Sierra Nevada near the west margin of the Basin and Range are greater than predicted at sites in California. These higher MMI values may result from critical reflections due to layering near the base of the Sierra Nevada.

New methods of multimode fiber interferometer signal processing

NASA Astrophysics Data System (ADS)

Vitrik, Oleg B.; Kulchin, Yuri N.; Maxaev, Oleg G.; Kirichenko, Oleg V.; Kamenev, Oleg T.; Petrov, Yuri S.

1995-06-01

New methods of multimode fiber interferometers signal processing are suggested. For scheme of single fiber multimode interferometers with two excited modes, the method based on using of special fiber unit is developed. This unit provides the modes interaction and further sum optical field filtering. As a result the amplitude of output signal is modulated by external influence on interferometer. The stabilization of interferometer sensitivity is achieved by using additional special modulation of output signal. For scheme of single fiber multimode interferometers with excitation of wide mode spectrum, the signal of intermode interference is registered by photodiode matrix and then special electronic unit performs correlation processing. For elimination of temperature destabilization, the registered signal is adopted to multimode interferometers optical signal temperature changes. The achieved parameters for double mode scheme: temporary stability--0.6% per hour, sensitivity to interferometer length deviations--3,2 nm; for multimode scheme: temperature stability--(0.5%)/(K), temporary nonstability--0.2% per hour, sensitivity to interferometer length deviations--20 nm, dynamic range--35 dB.

The multiple mini-interview for selecting medical residents: first experience in the Middle East region.

PubMed

Ahmed, Ashraf; Qayed, Khalil Ibrahim; Abdulrahman, Mahera; Tavares, Walter; Rosenfeld, Jack

2014-08-01

Numerous studies have shown that multiple mini-interviews (MMI) provides a standard, fair, and more reliable method for assessing applicants. This article presents the first MMI experience for selection of medical residents in the Middle East culture and an Arab country. In 2012, we started using the MMI in interviewing applicants to the residency program of Dubai Health Authority. This interview process consisted of eight, eight-minute structured interview scenarios. Applicants rotated through the stations, each with its own interviewer and scenario. They read the scenario and were requested to discuss the issues with the interviewers. Sociodemographic and station assessment data provided for each applicant were analyzed to determine whether the MMI was a reliable assessment of the non-clinical attributes in the present setting of an Arab country. One hundred and eighty-seven candidates from 27 different countries were interviewed for Dubai Residency Training Program using MMI. They were graduates of 5 medical universities within United Arab Emirates (UAE) and 60 different universities outside UAE. With this applicant's pool, a MMI with eight stations, produced absolute and relative reliability of 0.8 and 0.81, respectively. The person × station interaction contributed 63% of the variance components, the person contributed 34% of the variance components, and the station contributed 2% of the variance components. The MMI has been used in numerous universities in English speaking countries. The MMI evaluates non-clinical attributes and this study provides further evidence for its reliability but in a different country and culture. The MMI offers a fair and more reliable assessment of applicants to medical residency programs. The present data show that this assessment technique applied in a non-western country and Arab culture still produced reliable results.

Argonne - Ring Resonators

Science.gov Websites

-- Link6 -- Integrated Photonic Spectrographs for Astronomy Optical Multi-Mode Interference Devices Dual Guiding, Modulating, and Emitting Light on Silicon Scope1 -- Scope 2 -- Lamp1 -- optical Ring Resonators

Terahertz wave polarization beam splitter using a cascaded multimode interference structure.

PubMed

Li, Jiu-sheng; Liu, Han; Zhang, Le

2014-08-01

A terahertz wave polarization beam splitter, based on two cascaded multimode interference structures with different widths, is designed and numerically demonstrated. The numerical calculation results show that the designed polarization beam splitter can split transverse-electric (TE) and transverse-magnetic (TM)-polarized terahertz waves into different propagation directions with high efficiency over a frequency range from 6.40 to 6.50 THz. This polarization beam splitter shows more than a 22.06 dB extinction ratio for TE-polarization and a 31.65 dB extinction ratio for TM-polarization. Using such a polarization beam splitter, the whole length of the polarization beam splitter is reduced to about 1/12 that of a conventional design. This enables the polarization beam splitter to be used in terahertz wave integrated circuit fields.

Multimode-singlemode-multimode fiber sensor for alcohol sensing application

NASA Astrophysics Data System (ADS)

Rofi'ah, Iftihatur; Hatta, A. M.; Sekartedjo, Sekartedjo

2016-11-01

Alcohol is volatile and flammable liquid which is soluble substances both on polar and non polar substances that has been used in some industrial sectors. Alcohol detection method now widely used one of them is the optical fiber sensor. In this paper used fiber optic sensor based on Multimode-Single-mode-Multimode (MSM) to detect alcohol solution at a concentration range of 0-3%. The working principle of sensor utilizes the modal interference between the core modes and the cladding modes, thus make the sensor sensitive to environmental changes. The result showed that characteristic of the sensor not affect the length of the single-mode fiber (SMF). We obtain that the sensor with a length of 5 mm of single-mode can sensing the alcohol with a sensitivity of 0.107 dB/v%.

A refractive index sensor based on taper Michelson interferometer in multimode fiber

NASA Astrophysics Data System (ADS)

Fu, Xinghu; Zhang, Jiangpeng; Wang, Siwen; Fu, Guangwei; Liu, Qiang; Jin, Wa; Bi, Weihong

2016-11-01

A refractive index sensor based on taper Michelson interferometer in multimode fiber is proposed. The Hydrofluoric acid corrosion processing is studied in the preparation of single cone multimode optical fiber sensor. The taper Michelson interferometer is fabricated by changing corrosion time. The relationship between fiber sensor feature and corrosion time is analyzed. The experimental results show that the interference spectrum shift in the direction of short wave with the increase of the refractive index. The refractive index sensitivity can reach 115.8008 nm/RIU. Thereby, it can be used in detecting the refractive index in different areas including the environmental protection, health care and food production.

Validating MMI Scores: Are We Measuring Multiple Attributes?

ERIC Educational Resources Information Center

Oliver, Tom; Hecker, Kent; Hausdorf, Peter A.; Conlon, Peter

2014-01-01

The multiple mini-interview (MMI) used in health professional schools' admission processes is reported to assess multiple non-cognitive constructs such as ethical reasoning, oral communication, or problem evaluation. Though validation studies have been performed with total MMI scores, there is a paucity of information regarding how well MMI…

Manipulating attention via mindfulness induction improves P300-based brain-computer interface performance

NASA Astrophysics Data System (ADS)

Lakey, Chad E.; Berry, Daniel R.; Sellers, Eric W.

2011-04-01

In this study, we examined the effects of a short mindfulness meditation induction (MMI) on the performance of a P300-based brain-computer interface (BCI) task. We expected that MMI would harness present-moment attentional resources, resulting in two positive consequences for P300-based BCI use. Specifically, we believed that MMI would facilitate increases in task accuracy and promote the production of robust P300 amplitudes. Sixteen-channel electroencephalographic data were recorded from 18 subjects using a row/column speller task paradigm. Nine subjects participated in a 6 min MMI and an additional nine subjects served as a control group. Subjects were presented with a 6 × 6 matrix of alphanumeric characters on a computer monitor. Stimuli were flashed at a stimulus onset asynchrony (SOA) of 125 ms. Calibration data were collected on 21 items without providing feedback. These data were used to derive a stepwise linear discriminate analysis classifier that was applied to an additional 14 items to evaluate accuracy. Offline performance analyses revealed that MMI subjects were significantly more accurate than control subjects. Likewise, MMI subjects produced significantly larger P300 amplitudes than control subjects at Cz and PO7. The discussion focuses on the potential attentional benefits of MMI for P300-based BCI performance.

Novel spiroimidazopyridine derivative SAK3 improves methimazole-induced cognitive deficits in mice.

PubMed

Noreen, Husain; Yabuki, Yasushi; Fukunaga, Kohji

2017-09-01

Methimazole (MMI) is a first-line therapy used to manage hyperthyroidism and Graves' disease. Despite its therapeutic benefit, chronic MMI administration can lead to hypothyroidism and perturb brain homeostasis in patients, resulting in neuropsychiatric disorders such as depression and cognitive dysfunction. We recently developed the spiroimidazopyridine derivative SAK3 as cognitive enhancer; however, mechanisms underlying its activity remained unclear. Here, we show that SAK3 potentially improves cognitive impairment seen following MMI-induced hypothyroidism. Twenty-four hours after MMI (75 mg/kg, i.p.) treatment, we administered SAK3 (0.1, 0.5 and 1 mg/kg, p.o.) to mice daily for 7 days. MMI treatment alone disrupted olfactory bulb (OB) glomerular structure, as assessed by staining with the olfactory marker protein (OMP), reduced the number of choline acetyl transferase (ChAT)-immunoreactive neurons in medial septum (MS), and significantly impaired cognition. SAK3 (0.5 and 1 mg/kg, p.o.) administration significantly restored the number of cholinergic MS neurons in MMI-treated mice, and SAK3 treatment at a higher dose significantly improved cognitive deficits seen in MMI-treated control mice. Overall, our study suggests that SAK3 treatment could antagonize such impairment in patients with hypothyroidism. Copyright © 2017 Elsevier Ltd. All rights reserved.

The fairness, predictive validity and acceptability of multiple mini interview in an internationally diverse student population--a mixed methods study.

PubMed

Kelly, Maureen E; Dowell, Jon; Husbands, Adrian; Newell, John; O'Flynn, Siun; Kropmans, Thomas; Dunne, Fidelma P; Murphy, Andrew W

2014-12-21

International medical students, those attending medical school outside of their country of citizenship, account for a growing proportion of medical undergraduates worldwide. This study aimed to establish the fairness, predictive validity and acceptability of Multiple Mini Interview (MMI) in an internationally diverse student population. This was an explanatory sequential, mixed methods study. All students in First Year Medicine, National University of Ireland Galway 2012 were eligible to sit a previously validated 10 station MMI. Quantitative data comprised: demographics, selection tool scores and First Year Assessment scores. Qualitative data comprised separate focus groups with MMI Assessors, EU and Non-EU students. 109 students participated (45% of class). Of this 41.3% (n = 45) were Non-EU and 35.8% (n = 39) did not have English as first language. Age, gender and socioeconomic class did not impact on MMI scores. Non-EU students and those for whom English was not a first language achieved significantly lower scores on MMI than their EU and English speaking counterparts (difference in mean 11.9% and 12.2% respectively, P<0.001). MMI score was associated with English language proficiency (IELTS) (r = 0.5, P<0.01). Correlations emerged between First Year results and IELTS (r = 0.44; p = 0.006; n = 38) and EU school exit exam (r = 0.52; p<0.001; n = 56). MMI predicted EU student OSCE performance (r = 0.27; p = 0.03; n = 64). In the analysis of focus group data two overarching themes emerged: Authenticity and Cultural Awareness. MMI was considered a highly authentic assessment that offered a deeper understanding of the applicant than traditional tools, with an immediate relevance to clinical practice. Cultural specificity of some stations and English language proficiency were seen to disadvantage international students. Recommendations included cultural awareness training for MMI assessors, designing and piloting culturally neutral stations, lengthening station duration and providing high quality advance information to candidates. MMI is a welcome addition to assessment armamentarium for selection, particularly with regard to stakeholder acceptability. Understanding the mediating and moderating influences for differences in performance of international candidates is essential to ensure that MMI complies with the metrics of good assessment practice and principles of both distributive and procedural justice for all applicants, irrespective of nationality and cultural background.

Humidity sensor based on intracavity sensing of fiber ring laser

NASA Astrophysics Data System (ADS)

Shi, Jia; Xu, Wei; Xu, Degang; Wang, Yuye; Zhang, Chao; Yan, Chao; Yan, Dexian; He, Yixin; Tang, Longhuang; Zhang, Weihong; Yao, Jianquan

2017-10-01

A humidity sensor based on the intracavity sensing of a fiber ring laser is proposed and experimentally demonstrated. In the fiber ring laser, a humidity-sensitive fiber-optic multimode interferometer (MMI), fabricated by the single-mode-no-core-single-mode (SNCS) fiber coated with Agarose, works as the wavelength-selective filter for intracavity wavelength-modulated humidity sensing. The experiment shows that the lasing wavelength of the fiber laser has a good linear response to ambient humidity from 35%RH to 95%RH. The humidity sensitivity of -68 pm/%RH is obtained with a narrow 3 dB bandwidth less than 0.09 nm and a high signal-to-noise ratio (SNR)  ˜60 dB. The time response of the sensor has been measured to be as fast as 93 ms. The proposed sensor possesses a good stability and low temperature cross-sensitivity.

Clinical Study of 27 Patients with Medial Medullary Infarction.

PubMed

Akimoto, Takayoshi; Ogawa, Katsuhiko; Morita, Akihiko; Suzuki, Yutaka; Kamei, Satoshi

2017-10-01

Medial medullary infarction (MMI) is a rare ischemic stroke. Frequency of each neurological finding in MMI was different in each study. We retrospectively evaluated the medical records of patients with cerebral infarction who were admitted between March 1998 and October 2015. Patients in our study were diagnosed as having MMI by magnetic resonance image examination. Of 2727 patients with ischemic stroke, 27 patients (20 males and 7 females) had MMI. The MMI was complicated by infarcts located in the pons (n = 6), cerebellum (n = 2), and lateral medulla (n = 1). One patient had bilateral MMI. Large-artery atherosclerosis was the most common etiology. Motor weakness of the extremities was the most common neurological finding. Diminished contralateral superficial sensation was more common than diminished contralateral vibratory sensation, and these 2 types of sensory disturbance were often complicated. The patients with large MMI significantly more often accompanied diminished touch (P = .003), pain (P = .017), and vibratory (P = .019) sensation. Facial weakness was shown more common contralateral to the infarcts than ipsilateral (n = 8 contralateral, n = 1 ipsilateral). Lingual palsy was also more common contralateral to the lesions (n = 3 contralateral, n = 1 ipsilateral). One patient alone fulfilled the classical Dejerine triad. In MMI, motor weakness of extremities was commonly shown, and complication of diminished sensations indicated the large infarcts. As for facial weakness and lingual palsy, the supranuclear type was more prominent than the infranuclear type. Copyright © 2017 National Stroke Association. Published by Elsevier Inc. All rights reserved.

An exploration of the relationship between emotional intelligence (EI) and the Multiple Mini-Interview (MMI).

PubMed

Yen, Wendy; Hovey, Richard; Hodwitz, Kathryn; Zhang, Su

2011-03-01

The present study explored the relationship between the Multiple Mini-Interview (MMI) admissions process and the Bar-On EQ-i emotional intelligence (EI) instrument in order to investigate the potential for the EQ-i to serve as a proxy measure to the MMI. Participants were 196 health science candidates who completed both the MMI and the EQ-i as part of their admissions procedure at the Michener Institute for Applied Health Sciences. Three types of analyses were conducted to examine the relationship between the two tools: reliability analyses, correlational analyses, and a t-test. The tools were found to be moderately reliable. No significant relationships were found between the MMI and the EQ-i at the total or subscale level. The ability of the EQ-i to discriminate between accepted and not-accepted students was also not supported. These findings do not support the use of the EQ-i as a potential pre-screening tool for the MMI, but rather highlight the need to exercise caution when using emotional intelligence instruments for high-stakes admissions purposes.

Flat-top MZI filters: a novel robust design based on MMI splitters

NASA Astrophysics Data System (ADS)

Cherchi, Matteo; Harjanne, Mikko; Ylinen, Sami; Kapulainen, Markku; Vehmas, Tapani; Aalto, Timo

2016-03-01

Multimode Interferometers (MMIs) are an attractive alternative to directional couplers, ensuring more relaxed tolerances to fabrication errors and broader operation bandwidth. The drawback is that only a limited discrete set of splitting ratios is achievable with MMIs of constant cross section. This issue clearly limits their use in flat-top interferometric filters, which design requires, in general, free choice of the splitting ratios. Here we show for the first time that it is possible to design 4-stage flat-top interferometers using only standard MMIs with 50:50 and 85:15 splitting ratios. The design approach is based on the representation of the system on the Bloch sphere. Flat-top interleavers with different free spectral ranges have been designed and fabricated on the silicon photonics platform of VTT, based on 3 μm thick rib and strip waveguides. Two different layouts have been explored: one where all components are collinear and a more compact one which elements have been folded in a spiral shape. All interleavers have been designed for TE polarization, and they work in a wavelength range comparable with the 100 nm bandwidth of the MMI splitters. Even though fabrication imperfections and non-ideal behaviour of both waveguide bends and MMIs led to reduced extinction compared to simulations, most devices show in-band extinction exceeding 15 dB. The in-band losses of the most central channels did not exceed 1.5 dB compared to the reference straight waveguide. The designed interleavers can be employed in cascaded configurations to achieve broadband and fabrication tolerant flat-top wavelength (de)multiplexers.

Birth defects after use of antithyroid drugs in early pregnancy: a Swedish nationwide study.

PubMed

Andersen, Stine Linding; Lönn, Stefan; Vestergaard, Peter; Törring, Ove

2017-10-01

Antithyroid drugs (ATDs) may have teratogenic effects, but more evidence is needed on the risk and types of birth defects after the use of methimazole (MMI) and propylthiouracil (PTU). This study aimed to evaluate the association between the use of ATDs in early pregnancy and birth defects. Swedish nationwide register-based cohort study. The study included 684 340 children live-born in Sweden from 2006 to 2012. Exposure groups defined by maternal ATD use in early pregnancy were MMI ( n  = 162); PTU ( n  = 218); MMI and PTU ( n  = 66); ATD before or after, but not in pregnancy ( n  = 1551) and non-exposed (never ATD ( n  = 682 343)). Outcome was cumulative incidence of birth defects diagnosed before two years of age. The cumulative incidence of birth defects was not significantly different in children exposed to MMI (6.8%, P  = 0.6) or PTU (6.4%, P  = 0.4) vs non-exposed (8.0%). For subtypes of birth defects, MMI was associated with an increased incidence of septal heart defects ( P  = 0.02). PTU was associated with ear ( P  = 0.005) and obstructive urinary system malformations ( P  = 0.006). A case of choanal atresia was observed after exposure to both MMI and PTU. The incidence of birth defects in children born to mothers who received ATD before or after, but not in pregnancy, was 8.8% and not significantly different from non-exposed ( P  = 0.3), MMI exposed ( P  = 0.4) or PTU exposed ( P  = 0.2). MMI and PTU were associated with subtypes of birth defects previously reported, but the frequency of ATD exposure in early pregnancy was low and severe malformations described in the MMI embryopathy were rarely observed. © 2017 European Society of Endocrinology.

Multiple mini-interviews: same concept, different approaches.

PubMed

Knorr, Mirjana; Hissbach, Johanna

2014-12-01

Increasing numbers of educational institutions in the medical field choose to replace their conventional admissions interviews with a multiple mini-interview (MMI) format because the latter has superior reliability values and reduces interviewer bias. As the MMI format can be adapted to the conditions of each institution, the question of under which circumstances an MMI is most expedient remains unresolved. This article systematically reviews the existing MMI literature to identify the aspects of MMI design that have impact on the reliability, validity and cost-efficiency of the format. Three electronic databases (OVID, PubMed, Web of Science) were searched for any publications in which MMIs and related approaches were discussed. Sixty-six publications were included in the analysis. Forty studies reported reliability values. Generally, raising the number of stations has more impact on reliability than raising the number of raters per station. Other factors with positive influence include the exclusion of stations that are too easy, and the use of normative anchored rating scales or skills-based rater training. Data on criterion-related validities and analyses of dimensionality were found in 31 studies. Irrespective of design differences, the relationship between MMI results and academic measures is small to zero. The McMaster University MMI predicts in-programme and licensing examination performance. Construct validity analyses are mostly exploratory and their results are inconclusive. Seven publications gave information on required resources or provided suggestions on how to save costs. The most relevant cost factors that are additional to those of conventional interviews are the costs of station development and actor payments. The MMI literature provides useful recommendations for reliable and cost-efficient MMI designs, but some important aspects have not yet been fully explored. More theory-driven research is needed concerning dimensionality and construct validity, the predictive validity of MMIs other than those of McMaster University, the comparison of station types, and a cost-efficient station development process. © 2014 John Wiley & Sons Ltd.

Modified Mercalli intensities (MMI) for large earthquakes near New Madrid, Missouri, in 1811-1812 and near Charleston, South Carolina, in 1886

USGS Publications Warehouse

Bakun, W.H.; Johnston, A.C.; Hopper, M.G.

2002-01-01

Large historical earthquakes occurred in the eastern United States on December 16, 1811 near New Madrid, MO, on January 23, 1812 near New Madrid, MO, on February 7, 1812 near New Madrid, MO, and on September 1, 1886 near Charleston, SC. Modified Mercalli Intensity (MMI) assignments for these earthquakes were used by Bakun et al. (submitted) to estimate the location and moment magnitude M of these earthquakes from MMI observations. The MMI assignments used by Bakun et al. (submitted) are listed in this report.

[Multiple mini interviews before the occupation of main training posts in paediatrics].

PubMed

Hertel, Niels Thomas; Bjerager, Mia; Boas, Malene; Boisen, Kirsten A; Børch, Klaus; Frederiksen, Marianne Sjølin; Holm, Kirsten; Grum-Nymann, Anette; Johnsen, Martin M; Whitehouse, Stine; Balslev, Thomas

2013-09-09

Interviews are mandatory in Denmark when selecting doctors for training positions. We used multiple mini interviews (MMI) at four recruitment rounds for the main training posts in paediatrics. In total, 125 candidates were evaluated and assessed by CV and MMI (4-5 stations). Reliability for individual stations in MMI assessed by Cronbach's alpha was adequate (0.63-0.92). The overall reliability assessed by G-theory was lower, suggesting that different skills were tested. The acceptability was high. Our experiences with MMI suggest good feasibility and reliability. An increasing number of stations may improve the overall reliability.

A simple brain atrophy measure improves the prediction of malignant middle cerebral artery infarction by acute DWI lesion volume.

PubMed

Beck, Christoph; Kruetzelmann, Anna; Forkert, Nils D; Juettler, Eric; Singer, Oliver C; Köhrmann, Martin; Kersten, Jan F; Sobesky, Jan; Gerloff, Christian; Fiehler, Jens; Schellinger, Peter D; Röther, Joachim; Thomalla, Götz

2014-06-01

In patients with malignant middle cerebral artery infarction (MMI) decompressive surgery within 48 h improves functional outcome. In this respect, early identification of patients at risk of developing MMI is crucial. While the acute diffusion weighted imaging (DWI) lesion volume was found to predict MMI with high predictive values, the potential impact of preexisting brain atrophy on the course of space-occupying middle cerebral artery (MCA) infarction and the development of MMI remains unclear. We tested the hypothesis that the combination of the acute DWI lesion volume with simple measures of brain atrophy improves the early prediction of MMI. Data from a prospective, multicenter, observational study, which included patients with acute middle cerebral artery main stem occlusion studied by MRI within 6 h of symptom onset, was analyzed retrospectively. The development of MMI was defined according to the European randomized controlled trials of decompressive surgery. Acute DWI lesion volume, as well as brain and cerebrospinal fluid volume (CSF) were delineated. The intercaudate distance (ICD) was assessed as a linear brain atrophy marker by measuring the hemi-ICD of the intact hemisphere to account for local brain swelling. Binary logistic regression analysis was used to identify significant predictors of MMI. Cut-off values were determined by Classification and Regression Trees analysis. Sensitivity, specificity, positive predictive value (PPV), and negative predictive value (NPV) of the resulting models were calculated. Twenty-one (18 %) of 116 patients developed a MMI. Malignant middle cerebral artery infarctions patients had higher National Institutes of Health Stroke Scale scores on admission and presented more often with combined occlusion of the internal carotid artery and MCA. There were no differences in brain and CSF volume between the two groups. Diffusion weighted imaging lesion volume was larger (p < 0.001), while hemi-ICD was smaller (p = 0.029) in MMI patients. Inclusion of hemi-ICD improved the prediction of MMI. Best cut-off values to predict the development of MMI were DWI lesion volume > 87 ml and hemi-ICD ≤ 9.4 mm. The addition of hemi-ICD to the decision tree strongly increased PPV (0.93 vs. 0.70) resulting in a reduction of false positive findings from 7/23 (30 %) to 1/15 (7 %), while there were only slight changes in specificity, sensitivity and NPV. The absolute number of correct classifications increased by 4 (3.4 %). The integration of hemi-ICD as a linear marker of brain atrophy, that can easily be assessed in an emergency setting, may improve the prediction of MMI by lesion volume based predictive models.

Regulation of endotoxin-induced inhibition of macrophage migration by fresh serum.

PubMed Central

Heilman, D H

1977-01-01

Purified endotoxin (LPS) caused macrophage migration inhibition (MMI) in capillary tube cultures of guinea pig peritoneal macrophages in medium prepared with 15% fresh-frozen guinea pig serum. The inactivation of serum by heating at 56 degrees C for 30 min or by zymosan absorption prevented LPS-induced MMI. LPS was fully inhibitory in fresh C4-deficient guinea pig serum. Heat treatment of normal serum at 50 to 52 degrees C for 30 min to inactivate the alternate complement (C) pathway prevented or significantly decreased LPS-induced MMI, but heating C4-deficient serum at 50 to 52 degrees C for 30 min prevented LPS-MMI in all instances. These results suggest that the reaction was effected via the alternate C pathway but that some inhibition of migration was permitted via the classical C pathway, presumably due to antibodies for LPS in some normal sera. Pretreatment of normal serum with cobra venom factor decreased or prevented LPS-MMI in most instances, but similar results were obtained with C4-deficient serum. Experiments with chelated sera were unsuccessful because of the immobilization of macrophages by 10 mM ethylenediamine-tetraacetic acid and by 10 mM Mg-ethyleneglycol-bis (beta-aminoethyl)-N,N-tetraacetic acid. Low doses of concanavalin A and staphylococcal enterotoxin B and large doses of pokeweed mitogen caused MMI in "inactivated serum" medium, but MMI was enhanced in fresh serum. PMID:330407

Delivery of ultrashort spatially focused pulses through a multimode fiber

NASA Astrophysics Data System (ADS)

Morales-Delgado, Edgar E.; Papadopoulos, Ioannis N.; Farahi, Salma; Psaltis, Demetri; Moser, Christophe

2015-08-01

Multimode optical fibers potentially allow the transmission of larger amounts of information than their single mode counterparts because of their high number of supported modes. However, propagation of a light pulse through a multimode fiber suffers from spatial distortions due to the superposition of the various exited modes and from time broadening due to modal dispersion. We present a method based on digital phase conjugation to selectively excite in a multimode fiber specific optical fiber modes that follow similar optical paths as they travel through the fiber. The excited modes interfere constructively at the fiber output generating an ultrashort spatially focused pulse. The excitation of a limited number of modes following similar optical paths limits modal dispersion, allowing the transmission of the ultrashort pulse. We have experimentally demonstrated the delivery of a focused spot of pulse width equal to 500 fs through a 30 cm, 200 micrometer core step index multimode fiber. The results of this study show that two-photon imaging capability can be added to ultra-thin lensless endoscopy using commercial multimode fibers.

Delivery of an ultrashort spatially focused pulse to the other end of a multimode fiber using digital phase conjugation

NASA Astrophysics Data System (ADS)

Morales Delgado, Edgar E.; Papadopoulos, Ioannis N.; Farahi, Salma; Psaltis, Demetri; Moser, Christophe

2015-03-01

Multimode optical fibers potentially allow the transmission of larger amounts of information than their single mode counterparts because of their high number of supported modes. However, propagation of a light pulse through a multimode fiber suffers from spatial distortions due to the superposition of the various exited modes and from time broadening due to modal dispersion. We present a method based on digital phase conjugation to selectively excite in a multimode fiber specific optical fiber modes that follow similar optical paths as they travel through the fiber. The excited modes interfere constructively at the fiber output generating an ultrashort spatially focused pulse. The excitation of a limited number of modes following similar optical paths limits modal dispersion, allowing the transmission of the ultrashort pulse. We have experimentally demonstrated the delivery of a focused spot of pulse width equal to 500 fs through a 30 cm, 200 micrometer core step-index multimode fiber. The results of this study show that two-photon imaging capability can be added to ultra-thin lensless endoscopy using commercial multimode fibers.

Antithyroid drug-related hepatotoxicity in hyperthyroidism patients: a population-based cohort study

PubMed Central

Wang, Meng-Ting; Lee, Wan-Ju; Huang, Tien-Yu; Chu, Che-Li; Hsieh, Chang-Hsun

2014-01-01

Aims The evidence of hepatotoxicity of antithyroid drugs (ATDs) is limited to case reports or spontaneous reporting. This study aimed to quantify the incidence and comparative risks of hepatotoxicity for methimazole (MMI)/carbimazole (CBM) vs. propylthiouracil (PTU) in a population-based manner. Methods We conducted a cohort study of hyperthyroidism patients initially receiving MMI/CBM or PTU between 1 January 2004 and 31 December 2008 using the Taiwan National Health Insurance Research Database. The examined hepatotoxicity consisted of cholestasis, non-infectious hepatitis, acute liver failure and liver transplant, with the incidences and relative risks being quantified by Poisson exact methods and Cox proportional hazard models, respectively. Results The study cohort comprised 71 379 ATD initiators, with a median follow-up of 196 days. MMI/CBM vs. PTU users had a higher hepatitis incidence rate (3.17/1000 vs. 1.19/1000 person-years) but a lower incidence of acute liver failure (0.32/1000 vs. 0.68/1000 person-years). The relative risk analysis indicated that any use of MMI/CBM was associated with a 2.89-fold (95% CI 1.81, 4.60) increased hepatitis risk compared with PTU, with the risk increasing to 5.08-fold for high dose MMI/CBM (95% CI 3.15, 8.18). However, any MMI/CBM use vs. PTU was not related to an increased risk of cholestasis (adjusted hazard ratio [HR] 1.14, 95% CI 0.40, 3.72) or acute liver failure (adjusted HR 0.54, 95% CI 0.24, 1.22). Conclusions MMI/CBM and PTU exert dissimilar incidence rates of hepatotoxicity. Compared to PTU, MMI/CBM are associated in a dose-dependent manner with an increased risk for hepatitis while the risks are similar for acute liver failure and cholestasis. PMID:25279406

Student nurse selection and predictability of academic success: The Multiple Mini Interview project.

PubMed

Gale, Julia; Ooms, Ann; Grant, Robert; Paget, Kris; Marks-Maran, Di

2016-05-01

With recent reports of public enquiries into failure to care, universities are under pressure to ensure that candidates selected for undergraduate nursing programmes demonstrate academic potential as well as characteristics and values such as compassion, empathy and integrity. The Multiple Mini Interview (MMI) was used in one university as a way of ensuring that candidates had the appropriate numeracy and literacy skills as well as a range of communication, empathy, decision-making and problem-solving skills as well as ethical insights and integrity, initiative and team-work. To ascertain whether there is evidence of bias in MMIs (gender, age, nationality and location of secondary education) and to determine the extent to which the MMI is predictive of academic success in nursing. A longitudinal retrospective analysis of student demographics, MMI data and the assessment marks for years 1, 2 and 3. One university in southwest London. One cohort of students who commenced their programme in September 2011, including students in all four fields of nursing (adult, child, mental health and learning disability). Inferential statistics and a Bayesian Multilevel Model. MMI in conjunction with MMI numeracy test and MMI literacy test shows little or no bias in terms of ages, gender, nationality or location of secondary school education. Although MMI in conjunction with numeracy and literacy testing is predictive of academic success, it is only weakly predictive. The MMI used in conjunction with literacy and numeracy testing appears to be a successful technique for selecting candidates for nursing. However, other selection methods such as psychological profiling or testing of emotional intelligence may add to the extent to which selection methods are predictive of academic success on nursing. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mode-medium instability and its correction with a Gaussian-reflectivity mirror

NASA Technical Reports Server (NTRS)

Webster, K. L.; Sung, C. C.

1992-01-01

A high-power CO2 laser beam is known to deteriorate after a few microseconds due to a mode-medium instability (MMI) which results from an intensity-dependent heating rate related to the vibrational-to-translational decay of the upper and lower CO2 lasing levels. An iterative numerical technique is developed to model the time evolution of the beam as it is affected by the MMI. The technique is used to study the MMI in an unstable CO2 resonator with a hard-edge output mirror for different parameters like the Fresnel number and the gas density. The results show that the mode of the hard edge unstable resonator deteriorates because of the diffraction ripples in the mode. A Gaussian-reflectivity mirror was used to correct the MMI. This mirror produces a smoother intensity profile which significantly reduces the effects of the MMI. Quantitative results on peak density variation and beam quality are presented.

Mode-medium instability and its correction with a Gaussian reflectivity mirror

NASA Technical Reports Server (NTRS)

Webster, K. L.; Sung, C. C.

1990-01-01

A high power CO2 laser beam is known to deteriorate after a few microseconds due to a mode-medium instability (MMI) which results from an intensity dependent heating rate related to the vibrational-to-translational decay of the upper and lower CO2 lasing levels. An iterative numerical technique is developed to model the time evolution of the beam as it is affected by the MMI. The technique is used to study the MMI in an unstable CO2 resonator with a hard-edge output mirror for different parameters like the Fresnel number and the gas density. The results show that the mode of the hard edge unstable resonator deteriorates because of the diffraction ripples in the mode. A Gaussian-reflectivity mirror was used to correct the MMI. This mirror produces a smoother intensity profile which significantly reduces the effects of the MMI. Quantitative results on peak density variation and beam quality are presented.

Comparing Simulated and Observed Spectroscopic Signatures of Mix in Omega Capsules

NASA Astrophysics Data System (ADS)

Tregillis, I. L.; Shah, R. C.; Hakel, P.; Cobble, J. A.; Murphy, T. J.; Krasheninnikova, N. S.; Hsu, S. C.; Bradley, P. A.; Schmitt, M. J.; Batha, S. H.; Mancini, R. C.

2012-10-01

The Defect-Induced Mix Experiment (DIME) campaign at Los Alamos National Laboratory uses multi-monochromatic X-ray imaging (MMI)footnotetextT. Nagayama, R.C. Mancini, R. Florido, et al, J. App. Phys. 109, 093303 (2011) to detect the migration of high-Z spectroscopic dopants into the hot core of an imploded capsule. We have developed an MMI post-processing tool for producing synthetic datasets from two- and three-dimensional Lagrangian numerical simulations of Omega and NIF shots. These synthetic datasets are of sufficient quality, and contain sufficient physics, that they can be analyzed in the same manner as actual MMI data. We have carried out an extensive comparison between simulated and observed MMI data for a series of polar direct-drive shots carried out at the Omega laser facility in January, 2011. The capsule diameter was 870 microns; the 15 micron CH ablators contained a 2 micron Ti-doped layer along the inner edge. All capsules were driven with 17 kJ; some capsules were manufactured with an equatorial ``trench'' defect. This talk will focus on the construction of spectroscopic-quality synthetic MMI datasets from numerical simulations, and their correlation with MMI measurements.

Earthquake Macro-zonation Based Peak Ground Acceleration, Modified Mercalli Intensity, And Type of Rocks around Matano Fault

NASA Astrophysics Data System (ADS)

Karnaen, Muh; Suriamihardja, D. A.; Maulana, A.; Jaya, A.

2018-03-01

This study aims to determine earthquake vulnerable zones. We conducted research on earthquake macro-zonation based on PGA, Modified Mercalli Intensity (MMI), and type of rocks around Matano Fault in the area of 1.60 S to 2.990 S and 120.50 E to 122.470 E. We have acquired Maximum PGA and Modified Mercalli Intensity (MMI) for each observation point on the ground from the four major earthquake events. The empirical model is used due to lack of acceleration data recorded. We tried some empirical methods, but the McGuire method is found to be acceptable for this area. The result gives the maximum variation of PGA which is ranged between 18.40 - 363.54 gals. While the variation of MMI using empirical Wald attenuation gives values ranging from 2.9 - 7.7 MMI. The most vulnerable zone is located around Sorowako city with PGA value of 326.55 gals and MMI value of 7.5 MMI. This area is between ultra-basic rock and metamorphic rock formation. The vulnerable zone is near largest earthquake 6.2 M on 15-02-2011.

A low-complexity region in the YTH domain protein Mmi1 enhances RNA binding.

PubMed

Stowell, James A W; Wagstaff, Jane L; Hill, Chris H; Yu, Minmin; McLaughlin, Stephen H; Freund, Stefan M V; Passmore, Lori A

2018-06-15

Mmi1 is an essential RNA-binding protein in the fission yeast Schizosaccharomyces pombe that eliminates meiotic transcripts during normal vegetative growth. Mmi1 contains a YTH domain that binds specific RNA sequences, targeting mRNAs for degradation. The YTH domain of Mmi1 uses a noncanonical RNA-binding surface that includes contacts outside the conserved fold. Here, we report that an N-terminal extension that is proximal to the YTH domain enhances RNA binding. Using X-ray crystallography, NMR, and biophysical methods, we show that this low-complexity region becomes more ordered upon RNA binding. This enhances the affinity of the interaction of the Mmi1 YTH domain with specific RNAs by reducing the dissociation rate of the Mmi1-RNA complex. We propose that the low-complexity region influences RNA binding indirectly by reducing dynamic motions of the RNA-binding groove and stabilizing a conformation of the YTH domain that binds to RNA with high affinity. Taken together, our work reveals how a low-complexity region proximal to a conserved folded domain can adopt an ordered structure to aid nucleic acid binding. © 2018 Stowell et al.

Coherent noise reduction in digital holographic microscopy by averaging multiple holograms recorded with a multimode laser.

PubMed

Pan, Feng; Yang, Lizhi; Xiao, Wen

2017-09-04

In digital holographic microscopy (DHM), it is undesirable to observe coherent noise in the reconstructed images. The sources of the noise are mainly the parasitic interference fringes caused by multiple reflections and the speckle pattern caused by the optical scattering on the object surface. Here we propose a noise reduction approach in DHM by averaging multiple holograms recorded with a multimode laser. Based on the periodicity of the temporal coherence of a multimode semiconductor laser, we acquire a series of holograms by changing the optical path length difference between the reference beam and object beam. Because of the use of low coherence light, we can remove the parasitic interference fringes caused by multiple reflections in the holograms. In addition, the coherent noise patterns change in this process due to the different optical paths. Therefore, the coherent noise can be reduced by averaging the multiple reconstructions with uncorrelated noise patterns. Several experiments have been carried out to validate the effectiveness of the proposed approach for coherent noise reduction in DHM. It is shown a remarkable improvement both in amplitude imaging quality and phase measurement accuracy.

Past-behavioural versus situational questions in a postgraduate admissions multiple mini-interview: a reliability and acceptability comparison.

PubMed

Yoshimura, Hiroshi; Kitazono, Hidetaka; Fujitani, Shigeki; Machi, Junji; Saiki, Takuya; Suzuki, Yasuyuki; Ponnamperuma, Gominda

2015-04-14

The Multiple Mini-Interview (MMI) mostly uses 'Situational' Questions (SQs) as an interview format within a station, rather than 'Past-Behavioural' Questions (PBQs), which are most frequently adopted in traditional single-station personal interviews (SSPIs) for non-medical and medical selection. This study investigated reliability and acceptability of the postgraduate admissions MMI with PBQ and SQ interview formats within MMI stations. Twenty-six Japanese medical graduates, first completed the two-year national obligatory initial postgraduate clinical training programme and then applied to three specialty training programmes - internal medicine, general surgery, and emergency medicine - in a Japanese teaching hospital, where they underwent the Accreditation Council for Graduate Medical Education (ACGME)-competency-based MMI. This MMI contained five stations, with two examiners per station. In each station, a PBQ, and then an SQ were asked consecutively. PBQ and SQ interview formats were not separated into two different stations, or the order of questioning of PBQs and SQs in individual stations was not changed due to lack of space and experienced examiners. Reliability was analysed for the scores of these two MMI question types. Candidates and examiners were surveyed on this experience. The PBQ and SQ formats had generalisability coefficients of 0.822 and 0.821, respectively. With one examiner per station, seven stations could produce a reliability of more than 0.80 in both PBQ and SQ formats. More than 60% of both candidates and examiners felt positive about the overall candidates' ability. All participants liked the fairness of this MMI when compared with the previously experienced SSPI. SQs were perceived more favourable by candidates; in contrast, PBQs were perceived more relevant by examiners. Both PBQs and SQs are equally reliable and acceptable as station interview formats in the postgraduate admissions MMI. However, the use of the two formats within the same station, and with a fixed order, is not the best to maximise its utility as an admission test. Future studies are required to evaluate how best the SQs and PBQs should be combined as station interview formats to enhance reliability, feasibility, acceptability and predictive validity of the MMI.

MMI: Increasing Community Collaboration

NASA Astrophysics Data System (ADS)

Galbraith, N. R.; Stocks, K.; Neiswender, C.; Maffei, A.; Bermudez, L.

2007-12-01

Building community requires a collaborative environment and guidance to help move members towards a common goal. An effective environment for community collaboration is a workspace that fosters participation and cooperation; effective guidance furthers common understanding and promotes best practices. The Marine Metadata Interoperability (MMI) project has developed a community web site to provide a collaborative environment for scientists, technologists, and data managers from around the world to learn about metadata and exchange ideas. Workshops, demonstration projects, and presentations also provide community-building opportunities for MMI. MMI has developed comprehensive online guides to help users understand and work with metadata standards, ontologies, and other controlled vocabularies. Documents such as "The Importance of Metadata Standards", "Usage vs. Discovery Vocabularies" and "Developing Controlled Vocabularies" guide scientists and data managers through a variety of metadata-related concepts. Members from eight organizations involved in marine science and informatics collaborated on this effort. The MMI web site has moved from Plone to Drupal, two content management systems which provide different opportunities for community-based work. Drupal's "organic groups" feature will be used to provide workspace for future teams tasked with content development, outreach, and other MMI mission-critical work. The new site is designed to enable members to easily create working areas, to build communities dedicated to developing consensus on metadata and other interoperability issues. Controlled-vocabulary-driven menus, integrated mailing-lists, member-based content creation and review tools are facets of the new web site architecture. This move provided the challenge of developing a hierarchical vocabulary to describe the resources presented on the site; consistent and logical tagging of web pages is the basis of Drupal site navigation. The new MMI web site presents enhanced opportunities for electronic discussions, focused collaborative work, and even greater community participation. The MMI project is beginning a new initiative to comprehensively catalog and document tools for marine metadata. The new MMI community-based web site will be used to support this work and to support the work of other ad-hoc teams in the future. We are seeking broad input from the community on this effort.

C-band fundamental/first-order mode converter based on multimode interference coupler on InP substrate

NASA Astrophysics Data System (ADS)

Limeng, Zhang; Dan, Lu; Zhaosong, Li; Biwei, Pan; Lingjuan, Zhao

2016-12-01

The design, fabrication and characterization of a fundamental/first-order mode converter based on multimode interference coupler on InP substrate were reported. Detailed optimization of the device parameters were investigated using 3D beam propagation method. In the experiments, the fabricated mode converter realized mode conversion from the fundamental mode to the first-order mode in the wavelength range of 1530-1565 nm with excess loss less than 3 dB. Moreover, LP01 and LP11 fiber modes were successfully excited from a few-mode fiber by using the device. This InP-based mode converter can be a possible candidate for integrated transceivers for future mode-division multiplexing system. Project supported by the National Basic Research Program of China (No. 2014CB340102) and in part by the National Natural Science Foundation of China (Nos. 61274045, 61335009).

Mode selecting switch using multimode interference for on-chip optical interconnects.

PubMed

Priti, Rubana B; Pishvai Bazargani, Hamed; Xiong, Yule; Liboiron-Ladouceur, Odile

2017-10-15

A novel mode selecting switch (MSS) is experimentally demonstrated for on-chip mode-division multiplexing (MDM) optical interconnects. The MSS consists of a Mach-Zehnder interferometer with tapered multi-mode interference couplers and TiN thermo-optic phase shifters for conversion and switching between the optical data encoded on the fundamental and first-order quasi-transverse electric (TE) modes. The C-band MSS exhibits a >25  dB switching extinction ratio and < -12 dB crosstalk. We validate the dynamic switching with a 25.8 kHz gating signal measuring switching times for both TE0 and TE1 modes of <10.9  μs. All channels exhibit less than 1.7 dB power penalty at a 10 -12 bit error rate, while switching the non-return-to-zero PRBS-31 data signals at 10  Gb/s.

Medical School Performance of Socioeconomically Disadvantaged and Underrepresented Minority Students Matriculating after a Multiple Mini-Interview.

PubMed

Jerant, Anthony; Henderson, Mark C; Griffin, Erin; Talamantes, Efrain; Fancher, Tonya; Sousa, Francis; Franks, Peter

2018-01-01

Multiple Mini-Interviews (MMIs) are increasingly used in medical school admissions. We previously reported that while under-represented minority (URM) status was not associated with MMI scores, self-designated disadvantaged applicants had lower MMI scores, possibly affecting their matriculation prospects. No studies have examined how URM status or socioeconomic disadvantage (SED) are associated with academic performance following admission through an MMI. We examined the adjusted associations of MMI scores, SED, and URM status with U.S. Medical Licensing Examination Steps 1 and 2 performance and third-year clerkship Honors, measures affecting residency matching. While URM status was not associated with the measures, students with greater SED had lower Step 1 scores and fewer Honors. Students with higher MMI scores had more Step 1 failures, but more Honors. The findings identify areas to address in medical school admissions, student support, and evaluation processes, which is important given the need for a more representative physician workforce.

Can the multiple mini-interview predict academic achievement in medical school?

PubMed

Kim, Ja Kyoung; Kang, Seok Hoon; Lee, Hee Jae; Yang, JeongHee

2014-09-01

The purpose of this study was to determine whether the multiple mini-interview (MMI) predicts academic achievement for subjects in a medical school curriculum. Of 49 students who were admitted in 2008, 46 students finished the entire medical education curriculum within 4 years. We calculated the Pearson correlation coefficients between the total MMI score of the 46 graduates and their academic achievements in all subjects of the curriculum. The correlation coefficients between total MMI score and academic achievement in Medical Interview and History Taking, Problem-Based Learning, Doctoring I, and Clinical Practice of Surgery ranged from 0.4 to 0.7, indicating that they were moderately related. The values between total MMI score and achievement in Research Overview, Technical and Procedural Skills, Clinical Performance Examinations 1 and 3, Clinical Practice of Laboratory Medicine and Psychiatry, Neurology, and Orthopedics ranged from 0.2 to 0.4, which meant that they were weakly related. MMI score can predict medical student' academic achievement in subjects in the medical humanities and clinical practice.

Mode/Medium Instability in CO2 Laser

NASA Technical Reports Server (NTRS)

Webster, K. L.; Sung, C. C.

1992-01-01

Report discribes theoretical study of model/medium instability (MMI) in CO2 laser. Purposes of study to extend, to small Fresnel numbers, previous study of MMI restricted to large Fresnel numbers and to study methods of previous studies, to suppress MMI. Method of primary interest involves replacement of hard edge output mirror in laser resonator with mirror, local reflectivity of which decreases with radial distance from optical axis according to Gaussian profile.

Toxicological considerations for antithyroid drugs in children.

PubMed

Karras, Spiros; Tzotzas, Themistoklis; Krassas, Gerasimos E

2011-04-01

Propylthiouracil (PTU), methimazole (MMI) and carbimazole are indicated for the treatment of hyperthyroidism in adult and pediatric patients. The aim of this review is to present all the relevant information regarding the use of antithyroid drugs (ATD) in pediatric thyrotoxic cases, the pediatric toxicology of ATD and the warning which has recently been issued for PTU by the FDA. Epidemiology, diagnosis and treatment of pediatric thyrotoxicosis are all presented in this article. The authors also extensively discuss the details regarding the pharmacology, bioactivation, biodisposition, bioavailability and pharmacokinetic properties of the two main ATD (MMI and PTU). The FDA recently reported that use of PTU is associated with a higher risk for clinically serious or fatal liver injury compared to MMI in both adult and pediatric patients. They also found that congenital malformations were reported approximately three times more often with prenatal exposure to MMI compared with PTU and especially with the use of MMI during the first trimester of pregnancy. The authors believe that PTU should not be used in pediatric patients unless the patient is allergic to or intolerant of MMI, and there are no other treatment options available. That being said, PTU may be the treatment of choice during, and just before, the first trimester of pregnancy.

Embryonic exposure to propylthiouracil disrupts left-right patterning in Xenopus embryos.

PubMed

van Veenendaal, Nicole R; Ulmer, Bärbel; Boskovski, Marko T; Fang, Xiefan; Khokha, Mustafa K; Wendler, Christopher C; Blum, Martin; Rivkees, Scott A

2013-02-01

Antithyroid medications are the preferred therapy for the treatment of Graves' disease during pregnancy. Propylthiouracil (PTU) is favored over methimazole (MMI) due to potential teratogenic concerns with MMI. This study was to determine the teratogenic potential of MMI and PTU using a validated Xenopus tropicalis embryo model. Embryos were exposed to 1 mM PTU (EC(50)=0.88 mM), 1 mM MMI, or vehicle control (water) from stages 2 to 45. Treated embryos were examined for gross morphological defects, ciliary function, and gene expression by in situ hybridization. Exposure to PTU, but not MMI, led to cardiac and gut looping defects and shortening along the anterior-posterior axis. PTU exposure during gastrulation (stage 8-12.5) was identified as the critical period of exposure leading to left-right (LR) patterning defects. Abnormal cilia polarization, abnormal cilia-driven leftward flow at the gastrocoel roof plate (GRP), and aberrant expression of both Coco and Pitx2c were associated with abnormal LR symmetry observed following PTU exposure. PTU is teratogenic during late blastula, gastrulation, and neurulation; whereas MMI is not. PTU alters ciliary-driven flow and disrupts the normal genetic program involved in LR axis determination. These studies have important implications for women taking PTU during early pregnancy.

Multiple mini-interview as a predictor of performance in the objective structured clinical examination among Physician Associates in the United Kingdom: a cohort study

PubMed Central

Kumar, Narendra; Bhardwaj, Shailaja; Rahman, Eqram

2018-01-01

Introduction Patient satisfaction and health care outcomes are directly linked to useful communication skills. Therefore, excellent interpersonal skills are imperative for health care professionals. Multiple mini-interview (MMI) is designed as a selection tool to assess the communication skills of applicants in medical schools during the admission process. However, objective structured clinical examination (OSCE) assesses students’ communication and clinical skills at the end of their academic terms. Recently, Anglia Ruskin University, Chelmsford, UK, adopted MMI in the selection process for the first cohort of MSc Physician Associate trainees for the academic year 2015–2016. This study aimed to determine the likelihood of MMI as a predictor of future performance of communication skills in the OSCE. Materials and methods The anonymous data of the average scores of communication skills attained in MMI and OSCE at the end of year 1 were collected for 30 students from the Physician Associate program team. Subsequently, Pearson’s correlation was computed to determine the relationship between the average scores of communication skills attained in MMI, and OSCE during trimester 2 and trimester 3 by the Physician Associate trainees. Results The study showed positive correlation between the scores of communication skills attained in MMI and OSCE during trimester 2 (r=0.956, n=30, p<0.001) and trimester 3 (r=0.966, n=30, p<0.001). Conclusion The study provides empirical evidence for the validity of MMI as a predictor of future performance of Physician Associate trainees’ communication skills during subsequent OSCEs. PMID:29695944

A Multispectral Micro-Imager for Lunar Field Geology

NASA Technical Reports Server (NTRS)

Nunez, Jorge; Farmer, Jack; Sellar, Glenn; Allen, Carlton

2009-01-01

Field geologists routinely assign rocks to one of three basic petrogenetic categories (igneous, sedimentary or metamorphic) based on microtextural and mineralogical information acquired with a simple magnifying lens. Indeed, such observations often comprise the core of interpretations of geological processes and history. The Multispectral Microscopic Imager (MMI) uses multi-wavelength, light-emitting diodes (LEDs) and a substrate-removed InGaAs focal-plane array to create multispectral, microscale reflectance images of geological samples (FOV 32 X 40 mm). Each pixel (62.5 microns) of an image is comprised of 21 spectral bands that extend from 470 to 1750 nm, enabling the discrimination of a wide variety of rock-forming minerals, especially Fe-bearing phases. MMI images provide crucial context information for in situ robotic analyses using other onboard analytical instruments (e.g. XRD), or for the selection of return samples for analysis in terrestrial labs. To further assess the value of the MMI as a tool for lunar exploration, we used a field-portable, tripod-mounted version of the MMI to image a variety of Apollo samples housed at the Lunar Experiment Laboratory, NASA s Johnson Space Center. MMI images faithfully resolved the microtextural features of samples, while the application of ENVI-based spectral end member mapping methods revealed the distribution of Fe-bearing mineral phases (olivine, pyroxene and magnetite), along with plagioclase feldspars within samples. Samples included a broad range of lithologies and grain sizes. Our MMI-based petrogenetic interpretations compared favorably with thin section-based descriptions published in the Lunar Sample Compendium, revealing the value of MMI images for astronaut and rover-mediated lunar exploration.

Multiple mini-interview as a predictor of performance in the objective structured clinical examination among Physician Associates in the United Kingdom: a cohort study.

PubMed

Kumar, Narendra; Bhardwaj, Shailaja; Rahman, Eqram

2018-01-01

Patient satisfaction and health care outcomes are directly linked to useful communication skills. Therefore, excellent interpersonal skills are imperative for health care professionals. Multiple mini-interview (MMI) is designed as a selection tool to assess the communication skills of applicants in medical schools during the admission process. However, objective structured clinical examination (OSCE) assesses students' communication and clinical skills at the end of their academic terms. Recently, Anglia Ruskin University, Chelmsford, UK, adopted MMI in the selection process for the first cohort of MSc Physician Associate trainees for the academic year 2015-2016. This study aimed to determine the likelihood of MMI as a predictor of future performance of communication skills in the OSCE. The anonymous data of the average scores of communication skills attained in MMI and OSCE at the end of year 1 were collected for 30 students from the Physician Associate program team. Subsequently, Pearson's correlation was computed to determine the relationship between the average scores of communication skills attained in MMI, and OSCE during trimester 2 and trimester 3 by the Physician Associate trainees. The study showed positive correlation between the scores of communication skills attained in MMI and OSCE during trimester 2 ( r =0.956, n=30, p <0.001) and trimester 3 ( r =0.966, n=30, p <0.001). The study provides empirical evidence for the validity of MMI as a predictor of future performance of Physician Associate trainees' communication skills during subsequent OSCEs.

Should efforts in favor of medical student diversity be focused during admissions or farther upstream?

PubMed

Reiter, Harold I; Lockyer, Jocelyn; Ziola, Barry; Courneya, Carol-Ann; Eva, Kevin

2012-04-01

Traditional medical school admissions assessment tools may be limiting diversity. This study investigates whether the Multiple Mini-Interview (MMI) is diversity-neutral and, if so, whether applying it with greater weight would dilute the anticipated negative impact of diversity-limiting admissions measures. Interviewed applicants to six medical schools in 2008 and 2009 underwent MMI. Predictor variables of MMI scores, grade point average (GPA), and Medical College Admission Test (MCAT) scores were correlated with diversity measures of age, gender, size of community of origin, income level, and self-declared aboriginal status. A subset of the data was then combined with variable weight assigned to predictor variables to determine whether weighting during the applicant selection process would affect diversity among chosen applicants. MMI scores were unrelated to gender, size of community of origin, and income level. They correlated positively with age and negatively with aboriginal status. GPA and MCAT correlated negatively with age and aboriginal status, GPA correlated positively with income level, and MCAT correlated positively with size of community of origin. Even extreme combinations of MMI and GPA weightings failed to increase diversity among applicants who would be selected on the basis of weighted criteria. MMI could not neutralize the diversity-limiting properties of academic scores as selection criteria to interview. Using academic scores in this way causes range restriction, counteracting attempts to enhance diversity using downstream admissions selection measures such as MMI. Diversity efforts should instead be focused upstream. These results lend further support for the development of pipeline programs.

Advanced analysis of forest fire clustering

NASA Astrophysics Data System (ADS)

Kanevski, Mikhail; Pereira, Mario; Golay, Jean

2017-04-01

Analysis of point pattern clustering is an important topic in spatial statistics and for many applications: biodiversity, epidemiology, natural hazards, geomarketing, etc. There are several fundamental approaches used to quantify spatial data clustering using topological, statistical and fractal measures. In the present research, the recently introduced multi-point Morisita index (mMI) is applied to study the spatial clustering of forest fires in Portugal. The data set consists of more than 30000 fire events covering the time period from 1975 to 2013. The distribution of forest fires is very complex and highly variable in space. mMI is a multi-point extension of the classical two-point Morisita index. In essence, mMI is estimated by covering the region under study by a grid and by computing how many times more likely it is that m points selected at random will be from the same grid cell than it would be in the case of a complete random Poisson process. By changing the number of grid cells (size of the grid cells), mMI characterizes the scaling properties of spatial clustering. From mMI, the data intrinsic dimension (fractal dimension) of the point distribution can be estimated as well. In this study, the mMI of forest fires is compared with the mMI of random patterns (RPs) generated within the validity domain defined as the forest area of Portugal. It turns out that the forest fires are highly clustered inside the validity domain in comparison with the RPs. Moreover, they demonstrate different scaling properties at different spatial scales. The results obtained from the mMI analysis are also compared with those of fractal measures of clustering - box counting and sand box counting approaches. REFERENCES Golay J., Kanevski M., Vega Orozco C., Leuenberger M., 2014: The multipoint Morisita index for the analysis of spatial patterns. Physica A, 406, 191-202. Golay J., Kanevski M. 2015: A new estimator of intrinsic dimension based on the multipoint Morisita index. Pattern Recognition, 48, 4070-4081.

Candidate Evaluation Using Targeted Construct Assessment in the Multiple Mini-Interview: A Multifaceted Rasch Model Analysis.

PubMed

McLaughlin, Jacqueline E; Singer, David; Cox, Wendy C

2017-01-01

Construct: A 7-station multiple mini-interview (MMI) circuit was implemented and assessed for 214 candidates rated by 37 interviewers (N = 1,498 ratings). The MMI stations were designed to assess 6 specific constructs (adaptability, empathy, integrity, critical thinking, teamwork [receiving instruction], teamwork [giving instruction]) and one open station about the candidate's interest in the school. Despite the apparent benefits of the MMI, construct-irrelevant variance continues to be a topic of study. Refining the MMI to more effectively measure candidate ability is critical to improving our ability to identify and select candidates that are equipped for success within health professions education and the workforce. Each station assessed a single construct and was rated by a single interviewer who was provided only the name of the candidate and no additional information about the candidate's background, application, or prior academic performance. All interviewers received online and in-person training in the fall prior to the MMI and the morning of the MMI. A 3-facet multifaceted Rasch measurement analysis was completed to determine interviewer severity, candidate ability, and MMI station difficulty and examine how the model performed overall (e.g., rating scale). Altogether, the Rasch measures explained 62.84% of the variance in the ratings. Differences in candidate ability explained 45.28% of the variance in the data, whereas differences in interviewer severity explained 16.09% of the variance in the data. None of the interviewers had Infit or Outfit mean-square scores greater than 1.7, and only 2 (5.4%) had mean-square scores less than 0.5. The data demonstrated acceptable fit to the multifaceted Rasch measurement model. This work is the first of its kind in pharmacy and provides insight into the development of an MMI that provides useful and meaningful candidate assessment ratings for institutional decision making.

Low muscle mass and risk of type 2 diabetes in middle-aged and older adults: findings from the KoGES.

PubMed

Son, Jang Won; Lee, Seong Su; Kim, Sung Rae; Yoo, Soon Jib; Cha, Bong Yun; Son, Ho Young; Cho, Nam H

2017-05-01

Asians have a propensity to develop type 2 diabetes with a lower BMI than Western populations. This discrepancy may be due to differences in body fat and muscle mass for a given BMI. However, unlike adiposity, it is unclear whether muscle mass affects the risk of type 2 diabetes in Asian populations. We conducted a 2-yearly prospective assessment of 6895 participants who were free of diabetes at the baseline examination as part of the Korean Genome Epidemiology Study. The muscle mass index (MMI) was defined as the weight-adjusted appendicular skeletal muscle mass. Using Cox regression models, we evaluated the association between MMI and the risk of developing type 2 diabetes across sex-specific tertiles of MMI. Low muscle mass was defined as the sex-specific lowest tertile of MMI. Main covariates included age, sex, urban or rural residence, family history of diabetes, hypertension, smoking status, education level, monthly income, physical activity, alcohol consumption and diet. In addition, body fat mass, waist circumference and BMI were controlled as categorical variables. Obesity was defined as a BMI of ≥25 kg/m 2 or a waist circumference of ≥90 cm for men and ≥85 cm for women. During a median follow-up of 9.06 years, 1336 participants developed type 2 diabetes. At baseline, the mean age was 52.1 years and the mean BMI was 24.4 kg/m 2 . The mean MMI for men and women was 32.1% and 26.0%, respectively. There was an inverse association between MMI and the risk of type 2 diabetes. Multivariate-adjusted HRs for the risk of developing type 2 diabetes were 2.05 (95% CI 1.73, 2.43), 1.39 (95% CI 1.17, 1.66) and 1.0 from the lowest to highest sex-specific MMI tertile, with an HR of 1.35 (95% CI 1.26, 1.45) per SD decline in MMI. Further adjustments for fat mass, waist circumference and BMI as categorical variables did not modify the relationship (each p < 0.01). In BMI-stratified analyses, the population-attributable fraction of the lowest tertile of MMI for developing type 2 diabetes was increased by 11.9% in the non-obese group and 19.7% in the obese group. Low muscle mass as defined by MMI was associated with an increased risk of type 2 diabetes, independent of general obesity, in middle-aged and older Korean adults.

Wind- and Rain-Induced Vibrations Impose Different Selection Pressures on Multimodal Signaling.

PubMed

Halfwerk, Wouter; Ryan, Michael J; Wilson, Preston S

2016-09-01

The world is a noisy place, and animals have evolved a myriad of strategies to communicate in it. Animal communication signals are, however, often multimodal; their components can be processed by multiple sensory systems, and noise can thus affect signal components across different modalities. We studied the effect of environmental noise on multimodal communication in the túngara frog (Physalaemus pustulosus). Males communicate with rivals using airborne sounds combined with call-induced water ripples. We tested males under control as well as noisy conditions in which we mimicked rain- and wind-induced vibrations on the water surface. Males responded more strongly to a multimodal playback in which sound and ripples were combined, compared to a unimodal sound-only playback, but only in the absence of rain and wind. Under windy conditions, males decreased their response to the multimodal playback, suggesting that wind noise interferes with the detection of rival ripples. Under rainy conditions, males increased their response, irrespective of signal playback, suggesting that different noise sources can have different impacts on communication. Our findings show that noise in an additional sensory channel can affect multimodal signal perception and thereby drive signal evolution, but not always in the expected direction.

Multispectral Microscopic Imager (MMI): Multispectral Imaging of Geological Materials at a Handlens Scale

NASA Astrophysics Data System (ADS)

Farmer, J. D.; Nunez, J. I.; Sellar, R. G.; Gardner, P. B.; Manatt, K. S.; Dingizian, A.; Dudik, M. J.; McDonnell, G.; Le, T.; Thomas, J. A.; Chu, K.

2011-12-01

The Multispectral Microscopic Imager (MMI) is a prototype instrument presently under development for future astrobiological missions to Mars. The MMI is designed to be a arm-mounted rover instrument for use in characterizing the microtexture and mineralogy of materials along geological traverses [1,2,3]. Such geological information is regarded as essential for interpreting petrogenesis and geological history, and when acquired in near real-time, can support hypothesis-driven exploration and optimize science return. Correlated microtexure and mineralogy also provides essential data for selecting samples for analysis with onboard lab instruments, and for prioritizing samples for potential Earth return. The MMI design employs multispectral light-emitting diodes (LEDs) and an uncooled focal plane array to achieve the low-mass (<1kg), low-cost, and high reliability (no moving parts) required for an arm-mounted instrument on a planetary rover [2,3]. The MMI acquires multispectral, reflectance images at 62 μm/pixel, in which each image pixel is comprised of a 21-band VNIR spectrum (0.46 to 1.73 μm). This capability enables the MMI to discriminate and resolve the spatial distribution of minerals and textures at the microscale [2, 3]. By extending the spectral range into the infrared, and increasing the number of spectral bands, the MMI exceeds the capabilities of current microimagers, including the MER Microscopic Imager (MI); 4, the Phoenix mission Robotic Arm Camera (RAC; 5) and the Mars Science Laboratory's Mars Hand Lens Imager (MAHLI; 6). In this report we will review the capabilities of the MMI by highlighting recent lab and field applications, including: 1) glove box deployments in the Astromaterials lab at Johnson Space Center to analyze Apollo lunar samples; 2) GeoLab glove box deployments during the 2011 Desert RATS field trials in northern AZ to characterize analog materials collected by astronauts during simulated EVAs; 3) field deployments on Mauna Kea Volcano, Hawaii, during NASA's 2010 ISRU field trials, to analyze materials at the primary feedstock mining site; 4) lab characterization of geological samples from a complex, volcanic-hydrothermal terrain in the Cady Mts., SE Mojave Desert, California. We will show how field and laboratory applications have helped drive the development and refinement of MMI capabilities, while identifying synergies with other potential payload instruments (e.g. X-ray Diffraction) for solving real geological problems.

Reliability and acceptability of six station multiple mini-interviews: past-behavioural versus situational questions in postgraduate medical admission.

PubMed

Yamada, Toru; Sato, Juichi; Yoshimura, Hiroshi; Okubo, Tomoya; Hiraoka, Eiji; Shiga, Takashi; Kubota, Tadao; Fujitani, Shigeki; Machi, Junji; Ban, Nobutaro

2017-03-16

The multiple mini-interview (MMI) is increasingly used for postgraduate medical admissions and in undergraduate settings. MMIs use mostly Situational Questions (SQs) rather than Past-Behavioural Questions (PBQs). A previous study of MMIs in this setting, where PBQs and SQs were asked in the same order, reported that the reliability of PBQs was non-inferior to SQs and that SQs were more acceptable to candidates. The order in which the questions are asked may affect reliability and acceptability of an MMI. This study investigated the reliability of an MMI using both PBQs and SQs, minimising question order bias. Acceptability of PBQs and SQs was also assessed. Forty candidates applying for a postgraduate medical admission for 2016-2017 were included; 24 examiners were used. The MMI consisted of six stations with one examiner per station; a PBQ and a SQ were asked at every station, and the order of questions was alternated between stations. Reliability was analysed for scores obtained for PBQs or SQs separately, and for both questions. A post-MMI survey was used to assess the acceptability of PBQs and SQs. The generalisability (G) coefficients for PBQs only, SQs only, and both questions were 0.87, 0.96, and 0.80, respectively. Decision studies suggested that a four-station MMI would also be sufficiently reliable (G-coefficients 0.82 and 0.94 for PBQs and SQs, respectively). In total, 83% of participants were satisfied with the MMI. In terms of face validity, PBQs were more acceptable than SQs for candidates (p = 0.01), but equally acceptable for examiners (88% vs. 83% positive responses for PBQs vs. SQs; p = 0.377). Candidates preferred PBQs to SQs when asked to choose one, though this difference was not significant (p = 0.081); examiners showed a clear preference for PBQs (p = 0.007). Reliability and acceptability of six-station MMI were good among 40 postgraduate candidates; modelling suggested that four stations would also be reliable. SQs were more reliable than PBQs. Candidates found PBQs more acceptable than SQs and examiners preferred PBQs when they had to choose between the two. Our findings suggest that it is better to ask both PBQs and SQs during an MMI to maximise acceptability.

Effect of antithyroid drug on chick embryos during the last week of development: delayed hatching and decreased cerebellar acetylcholinesterase activity.

PubMed

Haba, Gen; Nishigori, Hidekazu; Tezuka, Yu; Kagami, Keisuke; Sugiyama, Toru; Nishigori, Hideo

2011-11-01

Hypothyroid state during embryogenesis disturbs normal growth and brain development, influencing later life. To evaluate the harmful consequences of the state during embryogenesis using an animal model, we inhibited thyroid hormone biosynthesis in chick embryos by using methimazole (MMI). Typically, embryos were treated with MMI (20 µmol/egg) on day 14, and examined on specific days.  Of the control embryos, 94% hatched on day 21, whereas 0% and 60% of MMI-treated embryos hatched on days 21 and 24, respectively. MMI retarded the rates of bodyweight gain as well as liver and heart development, and delayed hatching. However, the external differences in appearance and differences in the weights of the newly hatched control chicks on day 21 and the MMI-treated chicks on day 24 were less obvious. Embryos treated with MMI exhibited increased mass in their brain parts on day 24. Most notably, the treatment resulted in a 1.35-fold increase in cerebellum weight compared to that of the untreated animals. Acetylcholinesterase activity in the cerebellum on the day of hatching decreased significantly to 0.85-fold that of the untreated controls. Thyroid hormone receptor β mRNA was detected from day 12 and dramatically expressed from day 19 to the day of hatching. The 'fertilized hen's egg-chick embryo-chick system' is an appropriate animal model for investigating the hypothyroid state during embryogenesis. Decreased cerebellar acetylcholinesterase activity after MMI treatment was assumed to relate to a mechanism of motor and cognitive deficits in congenital hypothyroidism. © 2011 The Authors. Journal of Obstetrics and Gynaecology Research © 2011 Japan Society of Obstetrics and Gynecology.

Science applications of a multispectral microscopic imager for the astrobiological exploration of Mars

USGS Publications Warehouse

Nunez, Jorge; Farmer, Jack; Sellar, R. Glenn; Swayze, Gregg A.; Blaney, Diana L.

2014-01-01

Future astrobiological missions to Mars are likely to emphasize the use of rovers with in situ petrologic capabilities for selecting the best samples at a site for in situ analysis with onboard lab instruments or for caching for potential return to Earth. Such observations are central to an understanding of the potential for past habitable conditions at a site and for identifying samples most likely to harbor fossil biosignatures. The Multispectral Microscopic Imager (MMI) provides multispectral reflectance images of geological samples at the microscale, where each image pixel is composed of a visible/shortwave infrared spectrum ranging from 0.46 to 1.73 μm. This spectral range enables the discrimination of a wide variety of rock-forming minerals, especially Fe-bearing phases, and the detection of hydrated minerals. The MMI advances beyond the capabilities of current microimagers on Mars by extending the spectral range into the infrared and increasing the number of spectral bands. The design employs multispectral light-emitting diodes and an uncooled indium gallium arsenide focal plane array to achieve a very low mass and high reliability. To better understand and demonstrate the capabilities of the MMI for future surface missions to Mars, we analyzed samples from Mars-relevant analog environments with the MMI. Results indicate that the MMI images faithfully resolve the fine-scale microtextural features of samples and provide important information to help constrain mineral composition. The use of spectral endmember mapping reveals the distribution of Fe-bearing minerals (including silicates and oxides) with high fidelity, along with the presence of hydrated minerals. MMI-based petrogenetic interpretations compare favorably with laboratory-based analyses, revealing the value of the MMI for future in situ rover-mediated astrobiological exploration of Mars.

Science applications of a multispectral microscopic imager for the astrobiological exploration of Mars.

PubMed

Núñez, Jorge I; Farmer, Jack D; Sellar, R Glenn; Swayze, Gregg A; Blaney, Diana L

2014-02-01

Future astrobiological missions to Mars are likely to emphasize the use of rovers with in situ petrologic capabilities for selecting the best samples at a site for in situ analysis with onboard lab instruments or for caching for potential return to Earth. Such observations are central to an understanding of the potential for past habitable conditions at a site and for identifying samples most likely to harbor fossil biosignatures. The Multispectral Microscopic Imager (MMI) provides multispectral reflectance images of geological samples at the microscale, where each image pixel is composed of a visible/shortwave infrared spectrum ranging from 0.46 to 1.73 μm. This spectral range enables the discrimination of a wide variety of rock-forming minerals, especially Fe-bearing phases, and the detection of hydrated minerals. The MMI advances beyond the capabilities of current microimagers on Mars by extending the spectral range into the infrared and increasing the number of spectral bands. The design employs multispectral light-emitting diodes and an uncooled indium gallium arsenide focal plane array to achieve a very low mass and high reliability. To better understand and demonstrate the capabilities of the MMI for future surface missions to Mars, we analyzed samples from Mars-relevant analog environments with the MMI. Results indicate that the MMI images faithfully resolve the fine-scale microtextural features of samples and provide important information to help constrain mineral composition. The use of spectral endmember mapping reveals the distribution of Fe-bearing minerals (including silicates and oxides) with high fidelity, along with the presence of hydrated minerals. MMI-based petrogenetic interpretations compare favorably with laboratory-based analyses, revealing the value of the MMI for future in situ rover-mediated astrobiological exploration of Mars. Mars-Microscopic imager-Multispectral imaging-Spectroscopy-Habitability-Arm instrument.

Should total hip arthroplasty femoral components be designed to subside? A radiostereometric analysis study of the Charnley Elite and Exeter stems.

PubMed

Alfaro-Adrián, J; Gill, H S; Murray, D W

2001-08-01

The Charnley Elite and the Exeter stems have different design concepts: The former is designed not to subside, whereas the latter is expected to subside. This radiostereometric analysis study compares the early migration of the 2 stems. For both implants, the 1st year migration was about 4 times faster than the 2nd year. The Exeter migration was predominantly distal (1 mm/y in the 1st year). It also showed slight collapse into valgus, and the head migrated slowly posteriorly (0.3 mm/y in the 1st year). In contrast, the Elite had slow distal migration (0.2 mm/y in the 1st year) and rapid posterior head migration (0.8 mm/y in the 1st year). Four Elites and no Exeters had rapid posterior head migration rates (mean 2.8 mm/y in the 1st year and 0.8 mm/y in the 2nd year). The Elite and the Exeter stems have fundamentally different early patterns of migration, which affect their long-term function; 20% of the Elites and none of the Exeters had rapid posterior head migration in the 1st year and the 2nd year and are likely to fail early. Polished, collarless, tapered designs, such as the Exeter, may be more forgiving than conventional stems designed not to subside.

Can Multiple Mini-Interviews Predict Academic Performance of Dental Students? A Two-Year Follow-Up.

PubMed

Alaki, Sumer M; Yamany, Ibrahim A; Shinawi, Lana A; Hassan, Mona H A; Tekian, Ara

2016-11-01

Prior research has shown that students' previous grade point average (GPA) is the best predictor for future academic success. However, it can only partly predict the variability in dental school performance. The aim of this study was to assess the predictive value of multiple mini-interviews (MMI) as an admission criterion by comparing them with the academic performance of dental students over a two-year period. All incoming undergraduate dental students at the King Abdulaziz University Faculty of Dentistry (KAUFD) during academic year 2013-14 were invited to participate in MMI. Students rotated through six objective structured clinical exam (OSCE)-like stations for 30 minutes total and were interviewed by two trained faculty interviewers at each station. The stations were focused on noncognitive skills thought to be essential to academic performance at KAUFD. The academic performance of these students was then followed for two years and linked to their MMI scores. A total of 146 students (71 males and 75 females) participated in an interview (response rate=92.9%). Most students scored in the acceptable range at each MMI station. Students' total MMI score, ambitions, and motives were significant predictors of GPA during the two years of follow-up (p<0.038 and p<0.001, respectively). In this study, MMI was found to be able to predict future academic performance of undergraduate dental students.

Remission of insulin autoimmune syndrome in a patient with Grave's disease by treatment with methimazole.

PubMed

Okabe, R; Inaba, M; Hosoi, M; Ishimura, E; Kumeda, Y; Nishizawa, Y; Morii, H

1999-06-01

The patient, a 24-year-old man, had suffered from hunger, sweating, tachycardia and palpitation for three years. He was diagnosed as having Graves' disease (GD) and treated with methimazole (MMI) for 3 months. He noted that palpitation and perspiration seemed to particularly occur when he was hungry, and thus he was examined to determine whether these symptoms were caused by hypoglycemia. As a markedly elevated immunoreactive insulin level and the presence of insulin antibody in serum were found, he was diagnosed as having insulin autoimmune syndrome (IAS). HLA typing revealed the patient to be positive for group Bw62/Cw4/DR4, which is reportedly a specific HLA type in MMI-treated euthyoroid GD patients with IAS. In spite of the continuation of MMI treatment, the % binding of IRI decreased and the hypoglycemic episode disappeared. In contrast to the previously reported MMI induced IAS in GD cases, MMI is unlikely to have exacerbated IAS in the present case, although his HLA combination is identical to that of the previous cases.

Comparison of automatic traps to capture mosquitoes (Diptera: Culicidae) in rural areas in the tropical Atlantic rainforest

PubMed Central

de Sá, Ivy Luizi Rodrigues; Sallum, Maria Anice Mureb

2013-01-01

In several countries, surveillance of insect vectors is accomplished with automatic traps. This study addressed the performance of Mosquito Magnet® Independence (MMI) in comparison with those of CDC with CO2 and lactic acid (CDC-A) and CDC light trap (CDC-LT). The collection sites were in a rural region located in a fragment of secondary tropical Atlantic rainforest, southeastern Brazil. Limatus durhami and Limatus flavisetosus were the dominant species in the MMI, whereas Ochlerotatus scapularis was most abundant in CDC-A. Culex ribeirensis and Culex sacchettae were dominant species in the CDC-LT. Comparisons among traps were based on diversity indices. Results from the diversity analyses showed that the MMI captured a higher abundance of mosquitoes and that the species richness estimated with it was higher than with CDC-LT. Contrasting, difference between MMI and CDC-A was not statistically significant. Consequently, the latter trap seems to be both an alternative for the MMI and complementary to it for ecological studies and entomological surveillance. PMID:24402154

Polymer enabled 100 Gbaud connectivity for datacom applications

NASA Astrophysics Data System (ADS)

Katopodis, V.; Groumas, P.; Zhang, Z.; Dinu, R.; Miller, E.; Konczykowska, A.; Dupuy, J.-Y.; Beretta, A.; Dede, A.; Choi, J. H.; Harati, P.; Jorge, F.; Nodjiadjim, V.; Riet, Muriel; Cangini, G.; Vannucci, A.; Keil, N.; Bach, H.-G.; Grote, N.; Avramopoulos, H.; Kouloumentas, Ch.

2016-03-01

Polymers hold the promise for ultra-fast modulation of optical signals due to their potential for ultra-fast electro-optic (EO) response and high EO coefficient. In this work, we present the basic structure and properties of an efficient EO material system, and we summarize the efforts made within the project ICT-POLYSYS for the development of high-speed transmitters based on this system. More specifically, we describe successful efforts for the monolithic integration of multi-mode interference (MMI) couplers and Bragg-gratings (BGs) along with Mach-Zehnder modulators (MZMs) on this platform, and for the hybrid integration of InP active elements in the form of laser diodes (LDs) and gain chips (GCs). Using these integration techniques and the combination of the hybrid optical chips with ultra-fast indium phosphide double heterojunction bipolar transistor (InP-DHBT) electronics, we develop and fully package a single 100 Gb/s transmitter and a 2×100 Gb/s transmitter that can support serial operation at this rate with conventional non-return-to-zero on-off-keying (NRZ-OOK) modulation format. We also present the experimental evaluation of the devices, validating the efficiency of the monolithic and hybrid integration concepts and confirming the potential of this technology for single-lane 100 Gb/s optical connectivity in data-center network environments. Results from transmission experiments to this end include the achievement of BER close to 6·10-9 in B2B configuration, the achievement of BER lower than 10-7 for propagation over standard single-mode fiber (SSMF) with total length up to 1000 m, and the achievement of BER at the level of 10-5 after 1625 m of SSMF. Finally, plans for the use of the EO polymer system in a more complex hybrid integration platform for high-flexibility/high-capacity transmitters are also outlined.

Pollution going multimodal: the complex impact of the human-altered sensory environment on animal perception and performance

PubMed Central

Halfwerk, Wouter; Slabbekoorn, Hans

2015-01-01

Anthropogenic sensory pollution is affecting ecosystems worldwide. Human actions generate acoustic noise, emanate artificial light and emit chemical substances. All of these pollutants are known to affect animals. Most studies on anthropogenic pollution address the impact of pollutants in unimodal sensory domains. High levels of anthropogenic noise, for example, have been shown to interfere with acoustic signals and cues. However, animals rely on multiple senses, and pollutants often co-occur. Thus, a full ecological assessment of the impact of anthropogenic activities requires a multimodal approach. We describe how sensory pollutants can co-occur and how covariance among pollutants may differ from natural situations. We review how animals combine information that arrives at their sensory systems through different modalities and outline how sensory conditions can interfere with multimodal perception. Finally, we describe how sensory pollutants can affect the perception, behaviour and endocrinology of animals within and across sensory modalities. We conclude that sensory pollution can affect animals in complex ways due to interactions among sensory stimuli, neural processing and behavioural and endocrinal feedback. We call for more empirical data on covariance among sensory conditions, for instance, data on correlated levels in noise and light pollution. Furthermore, we encourage researchers to test animal responses to a full-factorial set of sensory pollutants in the presence or the absence of ecologically important signals and cues. We realize that such approach is often time and energy consuming, but we think this is the only way to fully understand the multimodal impact of sensory pollution on animal performance and perception. PMID:25904319

Simultaneous strain and temperature measure based on a single suspended core photonic crystal fiber

NASA Astrophysics Data System (ADS)

Rota-Rodrigo, S.; López-Amo, M.; Kobelke, J.; Schuster, K.; Santos, J. L.; Frazão, O.

2014-05-01

In this work a simultaneous strain and temperature sensor based on a suspended core fiber is proposed. The sensor comprises a 3mm suspended core PCF between SMFs and is based on the combination of two multimodal interferences with different frequency fringe patterns. The interference of the both signal has different sensitivity responses to strain and temperature. Thought a low-pass frequency filtering of the detected spectrum, the wavelength shift of the two interferences can be measured allowing the discrimination of strain and temperature simultaneously. The resolutions of this sensor are 0.45 ºC and 4.02 μɛ.

Development of Interference Lithography Capability Using a Helium Cadmium Ultraviolet Multimode Laser for the Fabrication of Sub-Micron-Structured Optical Materials

DTIC Science & Technology

2011-03-01

into separate parts, transmitted into different directions , and then recombined upon a surface to produce interference. The concern with this type of...photoresist (PR), is a radiation sensitive compound that is classified as positive or negative, depending on how it responds to radiation . Each is designed...emerging waves, and are referred to as diffraction gratings. Upon reflection from these kinds of gratings, light scattered from the periodic surface

Validity evidence for the Hamburg multiple mini-interview.

PubMed

Knorr, Mirjana; Schwibbe, Anja; Ehrhardt, Maren; Lackamp, Janina; Zimmermann, Stefan; Hampe, Wolfgang

2018-05-14

Multiple mini-interviews (MMI) become increasingly popular for the selection of medical students. In this work, we examine the validity evidence for the Hamburg MMI. We conducted three follow-up studies for the 2014 cohort of applicants to medical school over the course of two years. We calculated Spearman's rank correlation (ρ) between MMI results and (1) emotional intelligence measured by the Trait Emotional Intelligence Questionnaire (TEIQue-SF) and the Situational Test of Emotion Management (STEM), (2) supervisors' and practice team members' evaluations of psychosocial competencies and suitability for the medical profession after a one-week 1:1 teaching in a general practice (GP) and (3) objective structured clinical examination (OSCE) scores. There were no significant correlations between MMI results and the TEIQue-SF (ρ = .07, p > .05) or the STEM (ρ = .05, p > .05). MMI results could significantly predict GP evaluations of psychosocial competencies (ρ = .32, p < .05) and suitability for the medical profession (ρ = .42, p < .01) as well as OSCE scores (ρ = .23, p < .05). The MMI remained a significant predictor of these outcomes in a robust regression model including gender and age as control variables. Our findings suggest that MMIs can measure competencies that are relevant in a practical context. However, these competencies do not seem to be related to emotional intelligence as measured by self-report or situational judgement test.

The effects of aging on the working memory processes of multimodal information.

PubMed

Solesio-Jofre, Elena; López-Frutos, José María; Cashdollar, Nathan; Aurtenetxe, Sara; de Ramón, Ignacio; Maestú, Fernando

2017-05-01

Normal aging is associated with deficits in working memory processes. However, the majority of research has focused on storage or inhibitory processes using unimodal paradigms, without addressing their relationships using different sensory modalities. Hence, we pursued two objectives. First, was to examine the effects of aging on storage and inhibitory processes. Second, was to evaluate aging effects on multisensory integration of visual and auditory stimuli. To this end, young and older participants performed a multimodal task for visual and auditory pairs of stimuli with increasing memory load at encoding and interference during retention. Our results showed an age-related increased vulnerability to interrupting and distracting interference reflecting inhibitory deficits related to the off-line reactivation and on-line suppression of relevant and irrelevant information, respectively. Storage capacity was impaired with increasing task demands in both age groups. Additionally, older adults showed a deficit in multisensory integration, with poorer performance for new visual compared to new auditory information.

Deterministic Integration of Quantum Dots into on-Chip Multimode Interference Beamsplitters Using in Situ Electron Beam Lithography.

PubMed

Schnauber, Peter; Schall, Johannes; Bounouar, Samir; Höhne, Theresa; Park, Suk-In; Ryu, Geun-Hwan; Heindel, Tobias; Burger, Sven; Song, Jin-Dong; Rodt, Sven; Reitzenstein, Stephan

2018-04-11

The development of multinode quantum optical circuits has attracted great attention in recent years. In particular, interfacing quantum-light sources, gates, and detectors on a single chip is highly desirable for the realization of large networks. In this context, fabrication techniques that enable the deterministic integration of preselected quantum-light emitters into nanophotonic elements play a key role when moving forward to circuits containing multiple emitters. Here, we present the deterministic integration of an InAs quantum dot into a 50/50 multimode interference beamsplitter via in situ electron beam lithography. We demonstrate the combined emitter-gate interface functionality by measuring triggered single-photon emission on-chip with g (2) (0) = 0.13 ± 0.02. Due to its high patterning resolution as well as spectral and spatial control, in situ electron beam lithography allows for integration of preselected quantum emitters into complex photonic systems. Being a scalable single-step approach, it paves the way toward multinode, fully integrated quantum photonic chips.

Mode-locking of a terahertz laser by direct phase synchronization.

PubMed

Maysonnave, J; Maussang, K; Freeman, J R; Jukam, N; Madéo, J; Cavalié, P; Rungsawang, R; Khanna, S P; Linfield, E H; Davies, A G; Beere, H E; Ritchie, D A; Dhillon, S S; Tignon, J

2012-09-10

A novel scheme to achieve mode-locking of a multimode laser is demonstrated. Traditional methods to produce ultrashort laser pulses are based on modulating the cavity gain or losses at the cavity roundtrip frequency, favoring the pulsed emission. Here, we rather directly act on the phases of the modes, resulting in constructive interference for the appropriated phase relationship. This was performed on a terahertz quantum cascade laser by multimode injection seeding with an external terahertz pulse, resulting in phase mode-locked terahertz laser pulses of 9 ps duration, characterized unambiguously in the time domain.

A microfluidic multi-injector for gradient generation.

PubMed

Chung, Bong Geun; Lin, Francis; Jeon, Noo Li

2006-06-01

This paper describes a microfluidic multi-injector (MMI) that can generate temporal and spatial concentration gradients of soluble molecules. Compared to conventional glass micropipette-based methods that generate a single gradient, the MMI exploits microfluidic integration and actuation of multiple pulsatile injectors to generate arbitrary overlapping gradients that have not previously been possible. The MMI device is fabricated in poly(dimethylsiloxane) (PDMS) using multi-layer soft lithography and consists of fluidic channels and control channels with pneumatically actuated on-chip barrier valves. Repetitive actuation of on-chip valves control pulsatile release of solution that establishes microscopic chemical gradients around the orifice. The volume of solution released per actuation cycle ranged from 30 picolitres to several hundred picolitres and increased linearly with the duration of valve opening. The shape of the measured gradient profile agreed closely with the simulated diffusion profile from a point source. Steady state gradient profiles could be attained within 10 minutes, or less with an optimized pulse sequence. Overlapping gradients from 2 injectors were generated and characterized to highlight the advantages of MMI over conventional micropipette assays. The MMI platform should be useful for a wide range of basic and applied studies on chemotaxis and axon guidance.

Science Applications of a Multispectral Microscopic Imager for the Astrobiological Exploration of Mars

PubMed Central

Farmer, Jack D.; Sellar, R. Glenn; Swayze, Gregg A.; Blaney, Diana L.

2014-01-01

Abstract Future astrobiological missions to Mars are likely to emphasize the use of rovers with in situ petrologic capabilities for selecting the best samples at a site for in situ analysis with onboard lab instruments or for caching for potential return to Earth. Such observations are central to an understanding of the potential for past habitable conditions at a site and for identifying samples most likely to harbor fossil biosignatures. The Multispectral Microscopic Imager (MMI) provides multispectral reflectance images of geological samples at the microscale, where each image pixel is composed of a visible/shortwave infrared spectrum ranging from 0.46 to 1.73 μm. This spectral range enables the discrimination of a wide variety of rock-forming minerals, especially Fe-bearing phases, and the detection of hydrated minerals. The MMI advances beyond the capabilities of current microimagers on Mars by extending the spectral range into the infrared and increasing the number of spectral bands. The design employs multispectral light-emitting diodes and an uncooled indium gallium arsenide focal plane array to achieve a very low mass and high reliability. To better understand and demonstrate the capabilities of the MMI for future surface missions to Mars, we analyzed samples from Mars-relevant analog environments with the MMI. Results indicate that the MMI images faithfully resolve the fine-scale microtextural features of samples and provide important information to help constrain mineral composition. The use of spectral endmember mapping reveals the distribution of Fe-bearing minerals (including silicates and oxides) with high fidelity, along with the presence of hydrated minerals. MMI-based petrogenetic interpretations compare favorably with laboratory-based analyses, revealing the value of the MMI for future in situ rover-mediated astrobiological exploration of Mars. Key Words: Mars—Microscopic imager—Multispectral imaging—Spectroscopy—Habitability—Arm instrument. Astrobiology 14, 132–169. PMID:24552233

Pollution going multimodal: the complex impact of the human-altered sensory environment on animal perception and performance.

PubMed

Halfwerk, Wouter; Slabbekoorn, Hans

2015-04-01

Anthropogenic sensory pollution is affecting ecosystems worldwide. Human actions generate acoustic noise, emanate artificial light and emit chemical substances. All of these pollutants are known to affect animals. Most studies on anthropogenic pollution address the impact of pollutants in unimodal sensory domains. High levels of anthropogenic noise, for example, have been shown to interfere with acoustic signals and cues. However, animals rely on multiple senses, and pollutants often co-occur. Thus, a full ecological assessment of the impact of anthropogenic activities requires a multimodal approach. We describe how sensory pollutants can co-occur and how covariance among pollutants may differ from natural situations. We review how animals combine information that arrives at their sensory systems through different modalities and outline how sensory conditions can interfere with multimodal perception. Finally, we describe how sensory pollutants can affect the perception, behaviour and endocrinology of animals within and across sensory modalities. We conclude that sensory pollution can affect animals in complex ways due to interactions among sensory stimuli, neural processing and behavioural and endocrinal feedback. We call for more empirical data on covariance among sensory conditions, for instance, data on correlated levels in noise and light pollution. Furthermore, we encourage researchers to test animal responses to a full-factorial set of sensory pollutants in the presence or the absence of ecologically important signals and cues. We realize that such approach is often time and energy consuming, but we think this is the only way to fully understand the multimodal impact of sensory pollution on animal performance and perception. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Effects of selenium on short-term control of hyperthyroidism due to Graves' disease treated with methimazole: results of a randomized clinical trial.

PubMed

Leo, M; Bartalena, L; Rotondo Dottore, G; Piantanida, E; Premoli, P; Ionni, I; Di Cera, M; Masiello, E; Sassi, L; Tanda, M L; Latrofa, F; Vitti, P; Marcocci, C; Marinò, M

2017-03-01

In spite of previous conflicting results, an adjuvant role of selenium in the treatment of Graves' disease (GD) hyperthyroidism has been proposed. To address this issue, a randomized clinical trial was carried out aimed at investigating whether selenium is beneficial on the short-term control of GD hyperthyroidism treated with methimazole (MMI). Thirty newly diagnosed hyperthyroid GD patients were randomly assigned to treatment with: (i) MMI or (ii) MMI plus selenium. Primary outcomes were: control of hyperthyroidism and clinical and biochemical manifestations of hyperthyroidism [heart rate, cholesterol, sex hormone-binding globulin (SHBG), hyperthyroidism symptoms] at 90 days. Baseline features of the two groups did not differ. Serum selenium at baseline was similar in the two groups and within the recommended range to define selenium sufficiency. Selenium increased with treatment in the MMI-selenium group and became significantly higher than in the MMI group. Serum malondialdehyde, a marker of oxidative stress, was similar in the two groups and decreased significantly with treatment, with no difference between groups. Administration of MMI was followed by a reduction of FT 3 and FT 4 , with no difference between groups. Heart rate, SHBG and symptoms of hyperthyroidism decreased, whereas total cholesterol increased in both groups with no difference between groups. Our study, carried out in a selenium-sufficient cohort of GD patients, failed to show an adjuvant role of selenium in the short-term control of hyperthyroidism. However, selenium might be beneficial in patients from selenium-deficient areas, as well as in the long-term outcome of antithyroid treatment.

Utility of a writing station in the multiple mini-interview.

PubMed

Raghavan, Malathi; Burnett, Margaret; Martin, Bruce D; Christensen, Heather; Young, Deborah G; Mackalski, Barbara; Aoki, Fred

2013-01-01

The multiple mini-interview (MMI) is a reliable and valid method of selecting applicants for admission to health professional schools on the basis of non-cognitive traits. Because the MMI is a series of short interview stations that applicants rotate through in coordinated sequence, it can potentially be resource intensive. However, the MMI design has room for innovation and efficiency. At the University of Manitoba Faculty of Medicine, a 10-minute unsupervised writing station (WS) was incorporated into the MMI to obtain a writing sample from each applicant, to increase the number of independent scores per applicant, and to increase the number of applicants interviewed per circuit without increasing interviewer numbers. One assessor evaluated all the writing samples and assigned a score ranging from 1 to 7. With the inclusion of a WS into an 11-station MMI, the faculty's capacity to interview applicants increased by 9% (from 297 to 324) without substantially increasing interviewer hours needed per day. For 1,257 applicants interviewed in 2008-2011, the mean WS score was 4.03 (SD=1.36), whereas applicants' mean of 10 oral station (OS) scores was 4.62 (SD=0.69). Correlations between WS score and mean OS score ranged from .16 to .27 (p<.01) over the four years. Because inter-station correlations for OS ranged from .01 to .37, the correlation of .21 between WS and mean OS scores for all four years combined appears reasonable. Institutions that want to effectively increase the capacity of their MMI process might consider adding a WS.

Thyroid organotypic rat and human cultures used to investigate drug effects on thyroid function, hormone synthesis and release pathways

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vickers, Alison E.M., E-mail: vickers_alison@allergan.com; Heale, Jason; Sinclair, John R.

Drug induced thyroid effects were evaluated in organotypic models utilizing either a rat thyroid lobe or human thyroid slices to compare rodent and human response. An inhibition of thyroid peroxidase (TPO) function led to a perturbation in the expression of key genes in thyroid hormone synthesis and release pathways. The clinically used thiourea drugs, methimazole (MMI) and 6-n-propyl-2-thioruacil (PTU), were used to evaluate thyroid drug response in these models. Inhibition of TPO occurred early as shown in rat thyroid lobes (2 h) and was sustained in both rat (24–48 h) and human (24 h) with ≥ 10 μM MMI. Thyroidmore » from rats treated with single doses of MMI (30–1000 mg/kg) exhibited sustained TPO inhibition at 48 h. The MMI in vivo thyroid concentrations were comparable to the culture concentrations (∼ 15–84 μM), thus demonstrating a close correlation between in vivo and ex vivo thyroid effects. A compensatory response to TPO inhibition was demonstrated in the rat thyroid lobe with significant up-regulation of genes involved in the pathway of thyroid hormone synthesis (Tpo, Dio1, Slc5a5, Tg, Tshr) and the megalin release pathway (Lrp2) by 24 h with MMI (≥ 10 μM) and PTU (100 μM). Similarly, thyroid from the rat in vivo study exhibited an up-regulation of Dio1, Slc5a5, Lrp2, and Tshr. In human thyroid slices, there were few gene expression changes (Slc5a5, ∼ 2-fold) and only at higher MMI concentrations (≥ 1500 μM, 24 h). Extended exposure (48 h) resulted in up-regulation of Tpo, Dio1 and Lrp2, along with Slc5a5 and Tshr. In summary, TPO was inhibited by similar MMI concentrations in rat and human tissue, however an increased sensitivity to drug treatment in rat is indicated by the up-regulation of thyroid hormone synthesis and release gene pathways at concentrations found not to affect human tissue. -- Highlights: ► Novel model of rat thyroid or human thyroid slices to evaluate pathways of injury. ► TPO inhibition by MMI or PTU altered hormone synthesis and release genes. ► Rat thyroid was more sensitive to the drug effects than human tissue.« less

Bilateral Medial Medullary Infarction with Nondominant Vertebral Artery Occlusion.

PubMed

Zhang, Lei; Zhang, Gui-lian; Du, Ju-mei; Ma, Zhu-lin

2015-09-01

Bilateral medial medullary infarction (MMI) is a rare stroke subtype. Here, we report a case with bilateral MMI caused by nondominant vertebral artery occlusion confirmed by brain digital subtraction angiography and magnetic resonance imaging basi-parallel-anatomical-scanning. We highlight that anterior spinal arteries could originate from a unilateral vertebral artery (VA). Radiologists and neurologists should pay attention to the nondominant VA as bilateral MMI may be induced by occlusion of nondominant VA that supplies the bilateral anteromedial territories of the medulla. Copyright © 2015 National Stroke Association. Published by Elsevier Inc. All rights reserved.

First experience with multiple mini interview for medical school admission in Brazil: Does it work in a different cultural scenario?

PubMed

Daniel-Filho, Durval Anibal; Pires, Elda Maria Stafuzza Gonçalves; Paes, Angela Tavares; Troster, Eduardo Juan; Silva, Simone Cristina Azevedo B S; Granato, Mariana Fachini; Couto, Thomaz Bittencourt; Barreto, Joyce Kelly Silva; Campos, Alexandre Holthausen; Monte, Julio C Martins; Schvartsman, Claudio

2017-10-01

Evaluation of non-cognitive skills never has been used in Brazil. This study aims to evaluate Multiple Mini Interviews (MMI) in the admission process of a School of Medicine in São Paulo, Brazil. The population of the study comprised 240 applicants summoned for the interviews, and 96 raters. MMI contributed to 25% of the applicants' final grade. Eight scenarios were created with the aim of evaluating different non-cognitive skills, each one had two raters. At the end of the interviews, the applicants and raters described their impressions about MMI. The reliability of the MMI was analyzed using the Theory of Generalization and Many-Facet Rasch Model (MFRM). The G-study showed that the general reliability of the process was satisfactory (coefficient G = 0.743). The MMI grades were not affected by the raters' profile, time of interview (p = 0.715), and randomization group (p = 0.353). The Rasch analysis showed that there was no misfitting effects or inconsistent stations or raters. A significant majority of the applicants (98%) and all the raters believed MMIs were important in selecting students with a more adequate profile to study medicine. The general reliability of the selection process was excellent, and it was fully accepted by the applicants and raters.

MMI's Metadata and Vocabulary Solutions: 10 Years and Growing

NASA Astrophysics Data System (ADS)

Graybeal, J.; Gayanilo, F.; Rueda-Velasquez, C. A.

2014-12-01

The Marine Metadata Interoperability project (http://marinemetadata.org) held its public opening at AGU's 2004 Fall Meeting. For 10 years since that debut, the MMI guidance and vocabulary sites have served over 100,000 visitors, with 525 community members and continuous Steering Committee leadership. Originally funded by the National Science Foundation, over the years multiple organizations have supported the MMI mission: "Our goal is to support collaborative research in the marine science domain, by simplifying the incredibly complex world of metadata into specific, straightforward guidance. MMI encourages scientists and data managers at all levels to apply good metadata practices from the start of a project, by providing the best guidance and resources for data management, and developing advanced metadata tools and services needed by the community." Now hosted by the Harte Research Institute at Texas A&M University at Corpus Christi, MMI continues to provide guidance and services to the community, and is planning for marine science and technology needs for the next 10 years. In this presentation we will highlight our major accomplishments, describe our recent achievements and imminent goals, and propose a vision for improving marine data interoperability for the next 10 years, including Ontology Registry and Repository (http://mmisw.org/orr) advancements and applications (http://mmisw.org/cfsn).

Hong-Ou-Mandel Interference between Two Deterministic Collective Excitations in an Atomic Ensemble

NASA Astrophysics Data System (ADS)

Li, Jun; Zhou, Ming-Ti; Jing, Bo; Wang, Xu-Jie; Yang, Sheng-Jun; Jiang, Xiao; Mølmer, Klaus; Bao, Xiao-Hui; Pan, Jian-Wei

2016-10-01

We demonstrate deterministic generation of two distinct collective excitations in one atomic ensemble, and we realize the Hong-Ou-Mandel interference between them. Using Rydberg blockade we create single collective excitations in two different Zeeman levels, and we use stimulated Raman transitions to perform a beam-splitter operation between the excited atomic modes. By converting the atomic excitations into photons, the two-excitation interference is measured by photon coincidence detection with a visibility of 0.89(6). The Hong-Ou-Mandel interference witnesses an entangled NOON state of the collective atomic excitations, and we demonstrate its two times enhanced sensitivity to a magnetic field compared with a single excitation. Our work implements a minimal instance of boson sampling and paves the way for further multimode and multiexcitation studies with collective excitations of atomic ensembles.

Computational method for multi-modal microscopy based on transport of intensity equation

NASA Astrophysics Data System (ADS)

Li, Jiaji; Chen, Qian; Sun, Jiasong; Zhang, Jialin; Zuo, Chao

2017-02-01

In this paper, we develop the requisite theory to describe a hybrid virtual-physical multi-modal imaging system which yields quantitative phase, Zernike phase contrast, differential interference contrast (DIC), and light field moment imaging simultaneously based on transport of intensity equation(TIE). We then give the experimental demonstration of these ideas by time-lapse imaging of live HeLa cell mitosis. Experimental results verify that a tunable lens based TIE system, combined with the appropriate post-processing algorithm, can achieve a variety of promising imaging modalities in parallel with the quantitative phase images for the dynamic study of cellular processes.

Understanding reliability and some limitations of the images and spectra reconstructed from a multi-monochromatic x-ray imager

DOE PAGES

Nagayama, T.; Mancini, R. C.; Mayes, D.; ...

2015-11-18

Temperature and density asymmetry diagnosis is critical to advance inertial confinement fusion (ICF) science. A multi-monochromatic x-ray imager (MMI) is an attractive diagnostic for this purpose. The MMI records the spectral signature from an ICF implosion core with time resolution, 2-D space resolution, and spectral resolution. While narrow-band images and 2-D space-resolved spectra from the MMI data constrain temperature and density spatial structure of the core, the accuracy of the images and spectra depends not only on the quality of the MMI data but also on the reliability of the post-processing tools. In this paper, we synthetically quantify the accuracymore » of images and spectra reconstructed from MMI data. Errors in the reconstructed images are less than a few percent when the space-resolution effect is applied to the modeled images. The errors in the reconstructed 2-D space-resolved spectra are also less than a few percent except those for the peripheral regions. Spectra reconstructed for the peripheral regions have slightly but systematically lower intensities by ~6% due to the instrumental spatial-resolution effects. However, this does not alter the relative line ratios and widths and thus does not affect the temperature and density diagnostics. We also investigate the impact of the pinhole size variation on the extracted images and spectra. A 10% pinhole size variation could introduce spatial bias to the images and spectra of ~10%. A correction algorithm is developed, and it successfully reduces the errors to a few percent. Finally, it is desirable to perform similar synthetic investigations to fully understand the reliability and limitations of each MMI application.« less

The effect of personality traits on undergraduate dental students' performance in multiple mini interviews.

PubMed

Shinawi, Lana Ahmed; Alaki, Sumer Madani; Yamany, Ibrahim; Hassan, Mona Hassan Ahmed

2017-05-01

Multiple mini interviews (MMI) is a structured student selection method where applicants rotate around a series of stations that do not require previously learned knowledge. The Big Five Inventory (BFI) is a tool often used to measure personality traits commonly used in applicant selection. The aim of the current study was to assess the effect of personality traits using the BFI on undergraduate dental students' performance in MMI. This research was conducted at The Faculty of Dentistry, King Abdulaziz University, Jeddah, Saudi Arabia. All undergraduates applying to the dental program at King Abdulaziz University, Faculty of Dentistry (KAUFD) in two academic years [(2014-2015) and (2015-2016)] undertook the MMI held at KAUFD and completed the BFI inventory with a total number of 350 students. The MMI consisted of five stations while the BFI contained forty-four items. Data were analysed by SPSS version 20, using independent-samples t-test, Mann-Whitney U test, Spearman's rho correlation coefficient and Chi-square test. female students scored higher than their male counterparts but scores were only significant in the empathy station (p<0.001) in the first year, and in both empathetic skills and team work abilities (p<0.05) in the second. BFI results indicate that male students scored higher on agreeableness (p<0.003) and lower on neuroticism (p<0.001) in the first year while female students scored higher on agreeableness and conscientiousness (p<0.001) in the second year. Students of private schools had higher total MMI scores compared to those of public schools (p<0.05). MMI combined with the Big Five Inventory can be a useful tool in the admission process.

Acute Treatment with T-Type Calcium Channel Enhancer SAK3 Reduces Cognitive Impairments Caused by Methimazole-Induced Hypothyroidism Via Activation of Cholinergic Signaling.

PubMed

Husain, Noreen; Yabuki, Yasushi; Shinoda, Yasuharu; Fukunaga, Kohji

2018-01-01

Hypothyroidism is a common disorder that is associated with psychological disturbances such as dementia, depression, and psychomotor disorders. We recently found that chronic treatment with the T-type calcium channel enhancer SAK3 prevents the cholinergic neurodegeneration induced by a single intraperitoneal (i.p.) injection of methimazole (MMI; 75 mg/kg), thereby improving cognition. Here, we evaluated the acute effect of SAK3 on cognitive impairments and its mechanism of action following the induction of hypothyroidism. Hypothyroidism was induced by 2 injections of MMI (75 mg/kg, i.p.) administered once per week. Four weeks after the final MMI treatment, MMI-treated mice showed reduced serum thyroxine (T4) levels and cognitive impairments without depression-like behaviors. Although acute SAK3 (1.0 mg/kg, p.o.) administration failed to ameliorate the decreased T4 levels and histochemical destruction of the glomerular structure, acute SAK3 (1.0 mg/kg, p.o.) administration significantly reduced cognitive impairments in MMI-treated mice. Importantly, the α7 nicotinic acetylcholine receptor (nAChR)-selective inhibitor methyllycaconitine (MLA; 12 mg/kg, i.p.) and T-type calcium channel-specific blocker NNC 55-0396 (25 mg/kg, i.p.) antagonized the acute effect of SAK3 on memory deficits in MMI-treated mice. We also confirmed that acute SAK3 administration does not rescue reduced olfactory marker protein or choline acetyltransferase immunoreactivity levels in the olfactory bulb or medial septum. Taken together, these results suggest that SAK3 has the ability to improve the cognitive decline caused by hypothyroidism directly through activation of nAChR signaling and T-type calcium channels. © 2018 S. Karger AG, Basel.

Low elastic modulus Ti-Ta alloys for load-bearing permanent implants: enhancing the biodegradation resistance by electrochemical surface engineering.

PubMed

Kesteven, Jazmin; Kannan, M Bobby; Walter, Rhys; Khakbaz, Hadis; Choe, Han-Choel

2015-01-01

In this study, the in vitro degradation behaviour of titanium-tantalum (Ti-Ta) alloys (10-30 wt.% Ta) was investigated and compared with conventional implant materials, i.e., commercially pure titanium (Cp-Ti) and titanium-aluminium-vanadium (Ti6Al4V) alloy. Among the three Ti-Ta alloys studied, the Ti20Ta (6.3×10(-4) mm/y) exhibited the lowest degradation rate, followed by Ti30Ta (1.2×10(-3) mm/y) and Ti10Ta (1.4×10(-3) mm/y). All the Ti-Ta alloys exhibited lower degradation rate than that of Cp-Ti (1.8×10(-3) mm/y), which suggests that Ta addition to Ti is beneficial. As compared to Ti6Al4V alloy (8.1×10(-4) mm/y), the degradation rate of Ti20Ta alloy was lower by ~22%. However, the Ti30Ta alloy, which has closer elastic modulus to that of natural bone, showed ~48% higher degradation rate than that of Ti6Al4V alloy. Hence, to improve the degradation performance of Ti30Ta alloy, an intermediate thin porous layer was formed electrochemically on the alloy followed by calcium phosphate (CaP) electrodeposition. The coated Ti30Ta alloy (3.8×10(-3) mm/y) showed ~53% lower degradation rate than that of Ti6Al4V alloy. Thus, the study suggests that CaP coated Ti30Ta alloy can be a viable material for load-bearing permanent implants. Copyright © 2014 Elsevier B.V. All rights reserved.

Double-Blind, Placebo-Controlled, Randomized Trial of Selenium in Graves Hyperthyroidism.

PubMed

Kahaly, George J; Riedl, Michaela; König, Jochem; Diana, Tanja; Schomburg, Lutz

2017-11-01

Supplemental selenium (Se) may affect the clinical course of Graves disease (GD). Evaluate efficacy of add-on Se on medical treatment in GD. Double-blind, placebo-controlled, randomized supplementation trial. Academic endocrine outpatient clinic. Seventy untreated hyperthyroid patients with GD. Additionally to methimazole (MMI), patients received for 24 weeks either sodium selenite 300 µg/d po or placebo. MMI was discontinued at 24 weeks in euthyroid patients. Response rate (week 24), recurrence rate (week 36), and safety. A response was registered in 25 of 31 patients (80%) and in 27 of 33 (82%) at week 24 [odds ratio (OR) 0.93; 95% confidence interval (CI), 0.26 to 3.25; P = 0.904] in the Se (+MMI) and placebo (+MMI) groups, respectively. During a 12-week follow-up, 11 of 23 (48%) and 12 of 27 (44%) relapsed (OR 1.13; 95% CI, 0.29 to 2.66; P = 0.81) in the Se and placebo groups, respectively. Serum concentrations of Se and selenoprotein P were unrelated to response or recurrence rates. At week 36, 12 of 29 (41%) and 15 of 33 (45%) were responders and still in remission in the Se and placebo groups, respectively (OR 0.85; 95% CI, 0.31 to 2.32; P = 0.80). Serum levels of free triiodothyronine/free tetraiodothyronine, thyroid-stimulating hormone receptor antibody, prevalence of moderate to severe Graves orbitopathy, thyroid volume, and MMI starting dose were significantly lower in responders than in nonresponders. A total of 56 and 63 adverse events occurred in the Se and placebo groups, respectively (P = 0.164), whereas only one drug-related side effect (2.9%) was noted in 35 patients on placebo + MMI. Supplemental Se did not affect response or recurrence rates in GD. Copyright © 2017 Endocrine Society

Understanding reliability and some limitations of the images and spectra reconstructed from a multi-monochromatic x-ray imager

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nagayama, T.; Mancini, R. C.; Mayes, D.

2015-11-15

Temperature and density asymmetry diagnosis is critical to advance inertial confinement fusion (ICF) science. A multi-monochromatic x-ray imager (MMI) is an attractive diagnostic for this purpose. The MMI records the spectral signature from an ICF implosion core with time resolution, 2-D space resolution, and spectral resolution. While narrow-band images and 2-D space-resolved spectra from the MMI data constrain temperature and density spatial structure of the core, the accuracy of the images and spectra depends not only on the quality of the MMI data but also on the reliability of the post-processing tools. Here, we synthetically quantify the accuracy of imagesmore » and spectra reconstructed from MMI data. Errors in the reconstructed images are less than a few percent when the space-resolution effect is applied to the modeled images. The errors in the reconstructed 2-D space-resolved spectra are also less than a few percent except those for the peripheral regions. Spectra reconstructed for the peripheral regions have slightly but systematically lower intensities by ∼6% due to the instrumental spatial-resolution effects. However, this does not alter the relative line ratios and widths and thus does not affect the temperature and density diagnostics. We also investigate the impact of the pinhole size variation on the extracted images and spectra. A 10% pinhole size variation could introduce spatial bias to the images and spectra of ∼10%. A correction algorithm is developed, and it successfully reduces the errors to a few percent. It is desirable to perform similar synthetic investigations to fully understand the reliability and limitations of each MMI application.« less

Understanding reliability and some limitations of the images and spectra reconstructed from a multi-monochromatic x-ray imager.

PubMed

Nagayama, T; Mancini, R C; Mayes, D; Tommasini, R; Florido, R

2015-11-01

Temperature and density asymmetry diagnosis is critical to advance inertial confinement fusion (ICF) science. A multi-monochromatic x-ray imager (MMI) is an attractive diagnostic for this purpose. The MMI records the spectral signature from an ICF implosion core with time resolution, 2-D space resolution, and spectral resolution. While narrow-band images and 2-D space-resolved spectra from the MMI data constrain temperature and density spatial structure of the core, the accuracy of the images and spectra depends not only on the quality of the MMI data but also on the reliability of the post-processing tools. Here, we synthetically quantify the accuracy of images and spectra reconstructed from MMI data. Errors in the reconstructed images are less than a few percent when the space-resolution effect is applied to the modeled images. The errors in the reconstructed 2-D space-resolved spectra are also less than a few percent except those for the peripheral regions. Spectra reconstructed for the peripheral regions have slightly but systematically lower intensities by ∼6% due to the instrumental spatial-resolution effects. However, this does not alter the relative line ratios and widths and thus does not affect the temperature and density diagnostics. We also investigate the impact of the pinhole size variation on the extracted images and spectra. A 10% pinhole size variation could introduce spatial bias to the images and spectra of ∼10%. A correction algorithm is developed, and it successfully reduces the errors to a few percent. It is desirable to perform similar synthetic investigations to fully understand the reliability and limitations of each MMI application.

Development of a Benthic Macroinvertebrate Multimetric Index (MMI) for Neotropical Savanna Headwater Streams

EPA Science Inventory

Assessing the ecological impacts of anthropogenic pressures is a key task in environmental management. Multimetric indices (MMIs), based on aquatic assemblage responses to anthropogenic pressures, have been used increasingly throughout the world. The MMI approach is a low-cost, r...

Seismic Intensity, PGA and PGV for the South Napa Earthquake, August 24, 2014

NASA Astrophysics Data System (ADS)

Chen, S.; Pickering, A.; Mooney, W. D.; Crewdson, E.

2014-12-01

Numerous studies have investigated the statistical relationship between Modified Mercalli Intensity (MMI) and peak ground acceleration (PGA) and peak ground velocity (PGV). The Mw 6.0 South Napa (California) earthquake of August 24, 2014 provides valuable data to examine these relationships for both urban and rural environments within northern California. The finite fault model (D. Dreger, 2014) indicates that the fault rupture propagated predominantly NNW and up-dip from a 11-km-deep hypocenter. The epicentral location was 8 km SSW of downtown Napa. Recorded PGA north of the epicenter is as high as 600 cm/s2 and PGV locally reaches 80 cm/s. Field studies by two teams of investigators were conducted on August 24-26 and September 8-11, 2014 to assign MMI values at 108 sites. The highest MMI values are strongly localized along the NNW-SSE rupture trend north of the epicenter. Parts of the city of Napa and some communities several km farther north on Dry Creek Road were found to have experienced shaking intensities of MMI VII to VIII. The observed effects include houses moved off their foundations, chimney collapse or damage, cracked foundations and/or interior walls, broken windows, and the lateral displacement of heavy furniture. Communities to the east and west of this zone of high seismic intensity reported significantly lower values of MMI, typically IV and V even at distances as close as 10 km from the mapped surface rupture. In comparison with previous estimates by Wald et al. (1999) and Dangkua and Cramer (2011), we find that MMI III-VIII uniformly correspond to significantly larger (>150%) PGA and PGV values, as reported by the Center for Engineering Strong Motion Data (2014). We attribute this observation to two primary factors: (1) improved earthquake engineering in the post-Loma Prieta earthquake era that has led to building construction, both new and retrofitted, that is more resistant to earthquake strong ground motions; and (2) a frequency band relevant to these MMI estimates that contains less energy than that leading to the PGA or PGV values. The latter would primarily be a source effect.

Thyroid organotypic rat and human cultures used to investigate drug effects on thyroid function, hormone synthesis and release pathways.

PubMed

Vickers, Alison E M; Heale, Jason; Sinclair, John R; Morris, Stephen; Rowe, Josh M; Fisher, Robyn L

2012-04-01

Drug induced thyroid effects were evaluated in organotypic models utilizing either a rat thyroid lobe or human thyroid slices to compare rodent and human response. An inhibition of thyroid peroxidase (TPO) function led to a perturbation in the expression of key genes in thyroid hormone synthesis and release pathways. The clinically used thiourea drugs, methimazole (MMI) and 6-n-propyl-2-thioruacil (PTU), were used to evaluate thyroid drug response in these models. Inhibition of TPO occurred early as shown in rat thyroid lobes (2 h) and was sustained in both rat (24-48 h) and human (24 h) with ≥ 10 μM MMI. Thyroid from rats treated with single doses of MMI (30-1000 mg/kg) exhibited sustained TPO inhibition at 48 h. The MMI in vivo thyroid concentrations were comparable to the culture concentrations (~15-84 μM), thus demonstrating a close correlation between in vivo and ex vivo thyroid effects. A compensatory response to TPO inhibition was demonstrated in the rat thyroid lobe with significant up-regulation of genes involved in the pathway of thyroid hormone synthesis (Tpo, Dio1, Slc5a5, Tg, Tshr) and the megalin release pathway (Lrp2) by 24h with MMI (≥ 10 μM) and PTU (100 μM). Similarly, thyroid from the rat in vivo study exhibited an up-regulation of Dio1, Slc5a5, Lrp2, and Tshr. In human thyroid slices, there were few gene expression changes (Slc5a5, ~2-fold) and only at higher MMI concentrations (≥ 1500 μM, 24h). Extended exposure (48 h) resulted in up-regulation of Tpo, Dio1 and Lrp2, along with Slc5a5 and Tshr. In summary, TPO was inhibited by similar MMI concentrations in rat and human tissue, however an increased sensitivity to drug treatment in rat is indicated by the up-regulation of thyroid hormone synthesis and release gene pathways at concentrations found not to affect human tissue. Copyright © 2012 Elsevier Inc. All rights reserved.

Modelling Relations between Sensory Processing, Speech Perception, Orthographic and Phonological Ability, and Literacy Achievement

ERIC Educational Resources Information Center

Boets, Bart; Wouters, Jan; van Wieringen, Astrid; De Smedt, Bert; Ghesquiere, Pol

2008-01-01

The general magnocellular theory postulates that dyslexia is the consequence of a multimodal deficit in the processing of transient and dynamic stimuli. In the auditory modality, this deficit has been hypothesized to interfere with accurate speech perception, and subsequently disrupt the development of phonological and later reading and spelling…

Multi-mode acquisition (MMA): An MS/MS acquisition strategy for maximizing selectivity, specificity and sensitivity of DIA product ion spectra.

PubMed

Williams, Brad J; Ciavarini, Steve J; Devlin, Curt; Cohn, Steven M; Xie, Rong; Vissers, Johannes P C; Martin, LeRoy B; Caswell, Allen; Langridge, James I; Geromanos, Scott J

2016-08-01

In proteomics studies, it is generally accepted that depth of coverage and dynamic range is limited in data-directed acquisitions. The serial nature of the method limits both sensitivity and the number of precursor ions that can be sampled. To that end, a number of data-independent acquisition (DIA) strategies have been introduced with these methods, for the most part, immune to the sampling issue; nevertheless, some do have other limitations with respect to sensitivity. The major limitation with DIA approaches is interference, i.e., MS/MS spectra are highly chimeric and often incapable of being identified using conventional database search engines. Utilizing each available dimension of separation prior to ion detection, we present a new multi-mode acquisition (MMA) strategy multiplexing both narrowband and wideband DIA acquisitions in a single analytical workflow. The iterative nature of the MMA workflow limits the adverse effects of interference with minimal loss in sensitivity. Qualitative identification can be performed by selected ion chromatograms or conventional database search strategies. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fabrication tolerant chalcogenide mid-infrared multimode interference coupler design with applications for Bracewell nulling interferometry.

PubMed

Goldsmith, Harry-Dean Kenchington; Cvetojevic, Nick; Ireland, Michael; Madden, Stephen

2017-02-20

Understanding exoplanet formation and finding potentially habitable exoplanets is vital to an enhanced understanding of the universe. The use of nulling interferometry to strongly attenuate the central star's light provides the opportunity to see objects closer to the star than ever before. Given that exoplanets are usually warm, the 4 µm Mid-Infrared region is advantageous for such observations. The key performance parameters for a nulling interferometer are the extinction ratio it can attain and how well that is maintained across the operational bandwidth. Both parameters depend on the design and fabrication accuracy of the subcomponents and their wavelength dependence. Via detailed simulation it is shown in this paper that a planar chalcogenide photonic chip, consisting of three highly fabrication tolerant multimode interference couplers, can exceed an extinction ratio of 60 dB in double nulling operation and up to 40 dB for a single nulling operation across a wavelength window of 3.9 to 4.2 µm. This provides a beam combiner with sufficient performance, in theory, to image exoplanets.

Deterministic Integration of Quantum Dots into on-Chip Multimode Interference Beamsplitters Using in Situ Electron Beam Lithography

NASA Astrophysics Data System (ADS)

Schnauber, Peter; Schall, Johannes; Bounouar, Samir; Höhne, Theresa; Park, Suk-In; Ryu, Geun-Hwan; Heindel, Tobias; Burger, Sven; Song, Jin-Dong; Rodt, Sven; Reitzenstein, Stephan

2018-04-01

The development of multi-node quantum optical circuits has attracted great attention in recent years. In particular, interfacing quantum-light sources, gates and detectors on a single chip is highly desirable for the realization of large networks. In this context, fabrication techniques that enable the deterministic integration of pre-selected quantum-light emitters into nanophotonic elements play a key role when moving forward to circuits containing multiple emitters. Here, we present the deterministic integration of an InAs quantum dot into a 50/50 multi-mode interference beamsplitter via in-situ electron beam lithography. We demonstrate the combined emitter-gate interface functionality by measuring triggered single-photon emission on-chip with $g^{(2)}(0) = 0.13\\pm 0.02$. Due to its high patterning resolution as well as spectral and spatial control, in-situ electron beam lithography allows for integration of pre-selected quantum emitters into complex photonic systems. Being a scalable single-step approach, it paves the way towards multi-node, fully integrated quantum photonic chips.

MMI Preparatory School Computerized Model Library.

ERIC Educational Resources Information Center

Everhart, Nancy

This booklet provides a detailed description of the computerization of the library of MMI Preparatory School, a private, non-sectarian college preparatory school in Pennsylvania for students in grades 7 through 12. Each of the following functions is investigated: (1) catalog card production; (2) online reference services; (3) circulation; (4) word…

Hidden Item Variance in Multiple Mini-Interview Scores

ERIC Educational Resources Information Center

Zaidi, Nikki L.; Swoboda, Christopher M.; Kelcey, Benjamin M.; Manuel, R. Stephen

2017-01-01

The extant literature has largely ignored a potentially significant source of variance in multiple mini-interview (MMI) scores by "hiding" the variance attributable to the sample of attributes used on an evaluation form. This potential source of hidden variance can be defined as rating items, which typically comprise an MMI evaluation…

Impact and vibration detection in composite materials by using intermodal interference in multimode optical fibers

NASA Astrophysics Data System (ADS)

Malki, Abdelrafik; Gafsi, Rachid; Michel, Laurent; Labarrère, Michel; Lecoy, Pierre

1996-09-01

An optical fiber sensor based on the intermodal interference principle is integrated in a composite material to detect impacts and vibrations. Six fibers are integrated at the top of a carbon/epoxy composite panel so as to form a grid into the structure. Spectral and temporal responses to impacts and acoustic vibrations of the sensor are compared with a piezoelectric accelerometer. The tests proved the facility of integration and the high sensitivity of the device. The location of impacts is performed with this arrangement by measuring the arrival times of the front waves to the fibers.

Coherent storage of temporally multimode light using a spin-wave atomic frequency comb memory

NASA Astrophysics Data System (ADS)

Gündoǧan, M.; Mazzera, M.; Ledingham, P. M.; Cristiani, M.; de Riedmatten, H.

2013-04-01

We report on the coherent and multi-temporal mode storage of light using the full atomic frequency comb memory scheme. The scheme involves the transfer of optical atomic excitations in Pr3+:Y2SiO5 to spin waves in hyperfine levels using strong single-frequency transfer pulses. Using this scheme, a total of five temporal modes are stored and recalled on-demand from the memory. The coherence of the storage and retrieval is characterized using a time-bin interference measurement resulting in visibilities higher than 80%, independent of the storage time. This coherent and multimode spin-wave memory is promising as a quantum memory for light.

Ultra-small, self-holding, optical gate switch using Ge2Sb2Te5 with a multi-mode Si waveguide.

PubMed

Tanaka, Daiki; Shoji, Yuya; Kuwahara, Masashi; Wang, Xiaomin; Kintaka, Kenji; Kawashima, Hitoshi; Toyosaki, Tatsuya; Ikuma, Yuichiro; Tsuda, Hiroyuki

2012-04-23

We report a multi-mode interference-based optical gate switch using a Ge(2)Sb(2)Te(5) thin film with a diameter of only 1 µm. The switching operation was demonstrated by laser pulse irradiation. This switch had a very wide operating wavelength range of 100 nm at around 1575 nm, with an average extinction ratio of 12.6 dB. Repetitive switching over 2,000 irradiation cycles was also successfully demonstrated. In addition, self-holding characteristics were confirmed by observing the dynamic responses, and the rise and fall times were 130 ns and 400 ns, respectively. © 2012 Optical Society of America

NONLINEAR AND FIBER OPTICS: Analysis of the mode noise in interference fiber channels used for the distribution of microwave signals

NASA Astrophysics Data System (ADS)

Bratchikov, A. N.; Glukhov, I. P.

1991-03-01

The results are given of a statistical theory of the speckle generalized to interference channels used for the distribution of microwave signals using multimode fiber waveguides with step and graded refractive-index profiles. A method is described for estimating the mode noise level in the open and closed regimes with one longitudinal speckle. The influence of the degree of mode filtering, losses at microbends, and spectral properties of a laser source on the statistical properties and the mode noise level is demonstrated. Numerical estimates are obtained of the ratio of the powers of the signal and mode noise for interference channels with typical parameters of fiber waveguides and a qualitative description is given of the effect of the mode noise.

76 FR 75570 - Self-Regulatory Organizations; The Depository Trust Company; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-02

... counterparty by counterparty basis. Currently, all free money market instrument (``MMI'') deliveries are routed... was built in 1990 to route money market instrument (``MMI'') transactions for receiver approval. In... orders involve no securities, only money. \\5\\ The net debit cap control is designed so that DTC may...

Development of a regional littoral benthic macroinvertebrate multi-metric index (MMI) for lakes from the National Lakes Assessment

EPA Science Inventory

During the 2007 National Lakes Assessment (NLA) benthic macroinvertebrate samples were collected from the lake littoral zone. The purpose of the sampling was to assess the feasibility of a multi-metric index (MMI) to assess the condition of the littoral benthic macroinvertebrate...

Genomic organization, evolution and functional characterization of soluble toll-like receptor 5 (TLR5S) in miiuy croaker (Miichthys miiuy).

PubMed

Huo, Ruixuan; Zhao, Xueyan; Han, Jingjing; Xu, Tianjun

2018-05-30

Toll-like receptors (TLRs) play the key role in host defense of invasion of pathogens, not only in the innate immunity, but also in adaptive immunity. There are significant varieties and distinct features in fish TLRs, the TLR5 subfamily have two members (TLR5M and TLR5S). However, the exact role of TLR5 was lack of research in fish. In this study, a soluble form of TLR5 (TLR5S) was identified in miiuy croaker. The bioinformatics analysis showed that miiuy croaker TLR5S lacked the transmembrane domain and TIR domain. In other words, mmiTLR5S only has leucine-rich repeats (LRRs) domain, it is one of differences between TLR5M and TLR5S. Comparative genomic analysis showed that TLR5S might have happened an evolution between species. Expression analysis showed that mmiTLR5S was expressed in all tested miiuy croaker tissues and the mmiTLR5S expressions were significantly upregulated at 12 h in liver and kidney after Vibrio harveyi infection. Further functional experiments showed that NF-кB can be actived by mmiTLR5S, TLR5S might be an indispensable role in organism immune response. In short, the study of mmiTLR5S enriches the information of TLR5S and lays the foundation for future research on teleost TLRs system. Copyright © 2018 Elsevier Ltd. All rights reserved.

Developmental exposure to methimazole increases anxiety behavior in zebrafish.

PubMed

Reider, Masha; Connaughton, Victoria P

2015-10-01

The role of thyroid hormones in vertebrate development has been well documented for several decades. As hypothyroidism during critical periods of development can cause defects to the development of every major organ system, including brain, eye, and general morphology, we hypothesized that hypothyroidism would affect specific behaviors. To assess this, we treated zebrafish with the hypothyroid drug methimazole (MMI) and examined changes in anxiety, shoaling, vision, and locomotion. Following low-dose MMI exposure for the first 10 days of life, a time of rapid and significant development, larvae were removed from treatment and allowed to develop until 1 month of age. Comparisons between treated and controls took place between 10 and 30 days postfertilization to examine times both during and after treatment. Using the novel tank and startle response tests, we found that anxiety behaviors are significantly increased following MMI treatment. These effects persisted for several days following removal from treatment and indicate a prolonged effect of early hypothyroidism. However, permanent MMI effects on anxiety were not observed, as anxiety behaviors of early treated zebrafish recovered to control levels following 10 days out of treatment. In contrast to the strong link between MMI treatment and anxiety, shoaling and visual behaviors were not significantly affected within our experimental parameters. This indicates that disruption of thyroid system functioning early in life can differentially affect behavior by specifically altering anxiety responses without producing indiscriminate changes to overall behavioral development. (c) 2015 APA, all rights reserved).

Developing and piloting the multiple mini-interview in pre-registration student midwife selection in a UK setting.

PubMed

Callwood, Alison; Cooke, Debbie; Allan, Helen

2014-12-01

Published research has demonstrated that the multiple mini-interview (MMI) is a reliable assessment instrument in medical and nursing student selection. There is a dearth of evidence specifically relating to the advancement and subsequent evaluation of MMIs in the context of student midwife selection. To develop, pilot and examine the reliability of MMIs in pre-registration student midwife selection in a UK setting. DeVellis' framework for questionnaire development underpinned the generation of MMI scenarios. BSc (Hons) Midwifery Studies students at a Higher Education Institution in the UK volunteered to participate in 'mock' MMI circuits during the first week of their programme. An eight station model was piloted. Communication skills were rated at each station as a generic attribute. Station specific attributes assessed included: compassion and empathy; respect for difference and diversity; honesty and integrity; intellectual curiosity and reflective nature; advocacy; respect for privacy and dignity; team working and initiative; the role of the midwife and motivation to become a midwife. Participants' responses to scenario questions were rated on a 7 point scale. Cronbach's alpha scores measuring internal consistency ranged from 0.91 to 0.97 CONCLUSION: The systematic development of the MMI model and scenarios resulted in 'excellent' reliability across all stations. These findings endorse the MMI technique as a reliable alternative to the personal interview in informing final decisions in pre-registration student midwife selection. Copyright © 2014 Elsevier Ltd. All rights reserved.

Probabilistic Relationships between Ground‐Motion Parameters and Modified Mercalli Intensity in California

USGS Publications Warehouse

Worden, C.B.; Wald, David J.; Rhoades, D.A.

2012-01-01

We use a database of approximately 200,000 modified Mercalli intensity (MMI) observations of California earthquakes collected from USGS "Did You Feel It?" (DYFI) reports, along with a comparable number of peak ground-motion amplitudes from California seismic networks, to develop probabilistic relationships between MMI and peak ground velocity (PGV), peak ground acceleration (PGA), and 0.3-s, 1-s, and 3-s 5% damped pseudospectral acceleration (PSA). After associating each ground-motion observation with an MMI computed from all the DYFI responses within 2 km of the observation, we derived a joint probability distribution between MMI and ground motion. We then derived reversible relationships between MMI and each ground-motion parameter by using a total least squares regression to fit a bilinear function to the median of the stacked probability distributions. Among the relationships, the fit to peak ground velocity has the smallest errors, though linear combinations of PGA and PGV give nominally better results. We also find that magnitude and distance terms reduce the overall residuals and are justifiable on an information theoretic basis. For intensities MMI≥5, our results are in close agreement with the relations of Wald, Quitoriano, Heaton, and Kanamori (1999); for lower intensities, our results fall midway between Wald, Quitoriano, Heaton, and Kanamori (1999) and those of Atkinson and Kaka (2007). The earthquakes in the study ranged in magnitude from 3.0 to 7.3, and the distances ranged from less than a kilometer to about 400 km from the source.

Treatment of graves' disease with antithyroid drugs in the first trimester of pregnancy and the prevalence of congenital malformation.

PubMed

Yoshihara, Ai; Noh, JaedukYoshimura; Yamaguchi, Takuhiro; Ohye, Hidemi; Sato, Shiori; Sekiya, Kenichi; Kosuga, Yuka; Suzuki, Miho; Matsumoto, Masako; Kunii, Yo; Watanabe, Natsuko; Mukasa, Koji; Ito, Kunihiko; Ito, Koichi

2012-07-01

Several reports have suggested that propylthiouracil (PTU) may be safer than methimazole (MMI) for treating thyrotoxicosis during pregnancy because congenital malformations have been associated with the use of MMI during pregnancy. We investigated whether in utero exposure to antithyroid drugs resulted in a higher rate of major malformations than among the infants born to a control group of pregnant women. We reviewed the cases of women with Graves' disease who became pregnant. The pregnancy outcomes of 6744 women were known, and there were 5967 live births. MMI alone had been used to treat 1426 of the women, and 1578 women had been treated with PTU alone. The 2065 women who had received no medication for the treatment of Graves' disease during the first trimester served as the control group. The remaining women had been treated with potassium iodide, levothyroxine, or more than one drug during the first trimester. The antithyroid drugs were evaluated for associations with congenital malformations. The overall rate of major anomalies in the MMI group was 4.1% (50 of 1231), and it was significantly higher than the 2.1% (40 of 1906) in the control group (P = 0.002), but there was no increase in the overall rate of major anomalies in the PTU group in comparison with the control group (1.9%; 21 of 1399; P = 0.709). Seven of the 1231 newborns in the MMI group had aplasia cutis congenita, six had an omphalocele, seven had a symptomatic omphalomesenteric duct anomaly, and one had esophageal atresia. Hyperthyroidism in the first trimester of pregnancy did not increase the rate of congenital malformation. In utero exposure to MMI during the first trimester of pregnancy increased the rate of congenital malformations, and it significantly increased the rate of aplasia cutis congenita, omphalocele, and a symptomatic omphalomesenteric duct anomaly.

Novel Application of Quantitative Single-Photon Emission Computed Tomography/Computed Tomography to Predict Early Response to Methimazole in Graves' Disease

PubMed Central

Kim, Hyun Joo; Bang, Ji-In; Kim, Ji-Young; Moon, Jae Hoon; So, Young

2017-01-01

Objective Since Graves' disease (GD) is resistant to antithyroid drugs (ATDs), an accurate quantitative thyroid function measurement is required for the prediction of early responses to ATD. Quantitative parameters derived from the novel technology, single-photon emission computed tomography/computed tomography (SPECT/CT), were investigated for the prediction of achievement of euthyroidism after methimazole (MMI) treatment in GD. Materials and Methods A total of 36 GD patients (10 males, 26 females; mean age, 45.3 ± 13.8 years) were enrolled for this study, from April 2015 to January 2016. They underwent quantitative thyroid SPECT/CT 20 minutes post-injection of 99mTc-pertechnetate (5 mCi). Association between the time to biochemical euthyroidism after MMI treatment and %uptake, standardized uptake value (SUV), functional thyroid mass (SUVmean × thyroid volume) from the SPECT/CT, and clinical/biochemical variables, were investigated. Results GD patients had a significantly greater %uptake (6.9 ± 6.4%) than historical control euthyroid patients (n = 20, 0.8 ± 0.5%, p < 0.001) from the same quantitative SPECT/CT protocol. Euthyroidism was achieved in 14 patients at 156 ± 62 days post-MMI treatment, but 22 patients had still not achieved euthyroidism by the last follow-up time-point (208 ± 80 days). In the univariate Cox regression analysis, the initial MMI dose (p = 0.014), %uptake (p = 0.015), and functional thyroid mass (p = 0.016) were significant predictors of euthyroidism in response to MMI treatment. However, only %uptake remained significant in a multivariate Cox regression analysis (p = 0.034). A %uptake cutoff of 5.0% dichotomized the faster responding versus the slower responding GD patients (p = 0.006). Conclusion A novel parameter of thyroid %uptake from quantitative SPECT/CT is a predictive indicator of an early response to MMI in GD patients. PMID:28458607

Accounting for regional variation in both natural environment and human disturbance to improve performance of multimetric indices of lotic benthic diatoms.

PubMed

Tang, Tao; Stevenson, R Jan; Infante, Dana M

2016-10-15

Regional variation in both natural environment and human disturbance can influence performance of ecological assessments. In this study we calculated 5 types of benthic diatom multimetric indices (MMIs) with 3 different approaches to account for variation in ecological assessments. We used: site groups defined by ecoregions or diatom typologies; the same or different sets of metrics among site groups; and unmodeled or modeled MMIs, where models accounted for natural variation in metrics within site groups by calculating an expected reference condition for each metric and each site. We used data from the USEPA's National Rivers and Streams Assessment to calculate the MMIs and evaluate changes in MMI performance. MMI performance was evaluated with indices of precision, bias, responsiveness, sensitivity and relevancy which were respectively measured as MMI variation among reference sites, effects of natural variables on MMIs, difference between MMIs at reference and highly disturbed sites, percent of highly disturbed sites properly classified, and relation of MMIs to human disturbance and stressors. All 5 types of MMIs showed considerable discrimination ability. Using different metrics among ecoregions sometimes reduced precision, but it consistently increased responsiveness, sensitivity, and relevancy. Site specific metric modeling reduced bias and increased responsiveness. Combined use of different metrics among site groups and site specific modeling significantly improved MMI performance irrespective of site grouping approach. Compared to ecoregion site classification, grouping sites based on diatom typologies improved precision, but did not improve overall performance of MMIs if we accounted for natural variation in metrics with site specific models. We conclude that using different metrics among ecoregions and site specific metric modeling improve MMI performance, particularly when used together. Applications of these MMI approaches in ecological assessments introduced a tradeoff with assessment consistency when metrics differed across site groups, but they justified the convenient and consistent use of ecoregions. Copyright © 2016 Elsevier B.V. All rights reserved.

Macroseismic Intensity and Instrumental Ground Motion Parameter Correlations for Central Mexico

NASA Astrophysics Data System (ADS)

Sandoval Gómez, H.; Ramirez Guzman, L.; Espindola, V.

2012-12-01

We present instrumental intensity prediction equations for earthquakes in Central Mexico based on the correlation of observed Instrumental Ground-Motion Parameters (IGMP) and Modified Mercalli Intensity (MMI) scale reports. The goal of this study is to provide a model that can be used by the near real-time earthquake response system operated by the Institutes of Engineering and Geophysics at the National Autonomous University of Mexico (UNAM), which delivers estimates of key information associated with the societal impact due to earthquakes not available in the immediate aftermath of the event. Correlations of MMI and IGMP have been derived in other countries with different tectonic settings and built environments, but this is the first study devoted to the development of equations for the central region of Mexico. The IGMP are obtained from records of several stations for earthquakes with Mw 5.0-8.0 from the seismic networks operated by UNAM and other institutions in Mexico. The MMI observations were primarily obtained from the Did You Feel It (DYFI) report service of the U.S. Geological Survey and re-interpreted MMI reports from UNAM earthquake bulletin archives. For each instrumental observation we assigned a mean MMI intensity based on the proximity of the site where reported value are available, constrained by geological conditions and a visual inspection to guarantee that the intensity would be within one unit of the assigned value; following the procedure by Atkinson and Kaka (2006). We derived correlations for peak ground velocity (pgv) and acceleration, and three spectral acceleration periods (T=1, 2 and 3 s). In addition, we analyzed the Mw and distance dependence. We concluded that pgv and the spectral accelerations are the most useful IGMP predictors for MMI in the region of interest and the correlations differ significantly from those obtained in regions with other tectonic settings and infrastructure vulnerabilities (e.g. Wald et al, 1999; Atkinson and Kaka, 2006, Cramer and Dangkua, 2011).

The MMI Device Ontology: Enabling Sensor Integration

NASA Astrophysics Data System (ADS)

Rueda, C.; Galbraith, N.; Morris, R. A.; Bermudez, L. E.; Graybeal, J.; Arko, R. A.; Mmi Device Ontology Working Group

2010-12-01

The Marine Metadata Interoperability (MMI) project has developed an ontology for devices to describe sensors and sensor networks. This ontology is implemented in the W3C Web Ontology Language (OWL) and provides an extensible conceptual model and controlled vocabularies for describing heterogeneous instrument types, with different data characteristics, and their attributes. It can help users populate metadata records for sensors; associate devices with their platforms, deployments, measurement capabilities and restrictions; aid in discovery of sensor data, both historic and real-time; and improve the interoperability of observational oceanographic data sets. We developed the MMI Device Ontology following a community-based approach. By building on and integrating other models and ontologies from related disciplines, we sought to facilitate semantic interoperability while avoiding duplication. Key concepts and insights from various communities, including the Open Geospatial Consortium (eg., SensorML and Observations and Measurements specifications), Semantic Web for Earth and Environmental Terminology (SWEET), and W3C Semantic Sensor Network Incubator Group, have significantly enriched the development of the ontology. Individuals ranging from instrument designers, science data producers and consumers to ontology specialists and other technologists contributed to the work. Applications of the MMI Device Ontology are underway for several community use cases. These include vessel-mounted multibeam mapping sonars for the Rolling Deck to Repository (R2R) program and description of diverse instruments on deepwater Ocean Reference Stations for the OceanSITES program. These trials involve creation of records completely describing instruments, either by individual instances or by manufacturer and model. Individual terms in the MMI Device Ontology can be referenced with their corresponding Uniform Resource Identifiers (URIs) in sensor-related metadata specifications (e.g., SensorML, NetCDF). These identifiers can be resolved through a web browser, or other client applications via HTTP against the MMI Ontology Registry and Repository (ORR), where the ontology is maintained. SPARQL-based query capabilities, which are enhanced with reasoning, along with several supported output formats, allow the effective interaction of diverse client applications with the semantic information associated with the device ontology. In this presentation we describe the process for the development of the MMI Device Ontology and illustrate extensions and applications that demonstrate the benefits of adopting this semantic approach, including example queries involving inference. We also highlight the issues encountered and future work.

A Thyroid Hormone Challenge in Hypothyroid Rats Identifies T3 Regulated Genes in the Hypothalamus and in Models with Altered Energy Balance and Glucose Homeostasis

PubMed Central

Herwig, Annika; Campbell, Gill; Mayer, Claus-Dieter; Boelen, Anita; Anderson, Richard A.; Ross, Alexander W.; Mercer, Julian G.

2014-01-01

Background: The thyroid hormone triiodothyronine (T3) is known to affect energy balance. Recent evidence points to an action of T3 in the hypothalamus, a key area of the brain involved in energy homeostasis, but the components and mechanisms are far from understood. The aim of this study was to identify components in the hypothalamus that may be involved in the action of T3 on energy balance regulatory mechanisms. Methods: Sprague Dawley rats were made hypothyroid by giving 0.025% methimazole (MMI) in their drinking water for 22 days. On day 21, half the MMI-treated rats received a saline injection, whereas the others were injected with T3. Food intake and body weight measurements were taken daily. Body composition was determined by magnetic resonance imaging, gene expression was analyzed by in situ hybridization, and T3-induced gene expression was determined by microarray analysis of MMI-treated compared to MMI-T3-injected hypothalamic RNA. Results: Post mortem serum thyroid hormone levels showed that MMI treatment decreased circulating thyroid hormones and increased thyrotropin (TSH). MMI treatment decreased food intake and body weight. Body composition analysis revealed reduced lean and fat mass in thyroidectomized rats from day 14 of the experiment. MMI treatment caused a decrease in circulating triglyceride concentrations, an increase in nonesterified fatty acids, and decreased insulin levels. A glucose tolerance test showed impaired glucose clearance in the thyroidectomized animals. In the brain, in situ hybridization revealed marked changes in gene expression, including genes such as Mct8, a thyroid hormone transporter, and Agrp, a key component in energy balance regulation. Microarray analysis revealed 110 genes to be up- or downregulated with T3 treatment (±1.3-fold change, p<0.05). Three genes chosen from the differentially expressed genes were verified by in situ hybridization to be activated by T3 in cells located at or close to the hypothalamic ventricular ependymal layer and differentially expressed in animal models of long- and short-term body weight regulation. Conclusion: This study identified genes regulated by T3 in the hypothalamus, a key area of the brain involved in homeostasis and neuroendocrine functions. These include genes hitherto not known to be regulated by thyroid status. PMID:25087834

Reshaping a multimode laser beam into a constructed Gaussian beam for generating a thin light sheet.

PubMed

Saghafi, Saiedeh; Haghi-Danaloo, Nikoo; Becker, Klaus; Sabdyusheva, Inna; Foroughipour, Massih; Hahn, Christian; Pende, Marko; Wanis, Martina; Bergmann, Michael; Stift, Judith; Hegedus, Balazs; Dome, Balazs; Dodt, Hans-Ulrich

2018-06-01

Based on the modal analysis method, we developed a model that describes the output beam of a diode-pumped solid state (DPSS) laser emitting a multimode beam. Measuring the output beam profile in the near field and at the constructed far field the individual modes, their respective contributions, and their optical parameters are determined. Using this information, the beam is optically reshaped into a quasi-Gaussian beam by the interference and superposition of the various modes. This process is controlled by a mode modulator unit that includes different meso-aspheric elements and a soft-aperture. The converted beam is guided into a second optical unit comprising achromatic-aspheric elements to produce a thin light sheet for ultramicroscopy. We found that this light sheet is markedly thinner and exhibits less side shoulders compared with a light sheet directly generated from the output of a DPSS multimode laser. © 2018 The Authors. Journal of Biophotonics published by WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Psychometric Properties of the Multiple Mini-Interview Used for Medical Admissions: Findings from Generalizability and Rasch Analyses

ERIC Educational Resources Information Center

Sebok, Stefanie S.; Luu, King; Klinger, Don A.

2014-01-01

The multiple mini-interview (MMI) has become an increasingly popular admissions method for selecting prospective students into professional programs (e.g., medical school). The MMI uses a series of short, labour intensive simulation stations and scenario interviews to more effectively assess applicants' non-cognitive qualities such as…

77 FR 17534 - Self-Regulatory Organizations; The Depository Trust Company; Notice of Filing of Proposed Rule...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-26

... Association (``SIFMA'') formed the MMI Blue-Sky Task Force (``Task Force'') to address systemic and unique... processing. The Task Force, along other money market industry members,\\8\\ determined that DTC's current MMI... amount or proceeds after the 3 p.m. E.T. deadline for RTP instructions.\\9\\ Accordingly, DTC is proposing...

Monitoring Molecules in Neuroscience Then and Now

PubMed Central

Rice, Margaret E.

2017-01-01

The 16th International Conference on Monitoring Molecules in Neuroscience (MMiN) was held in Gothenburg, Sweden in late spring 2016. This conference originated as a methods meeting focused on in vivo voltammetric techniques and microdialysis. Over time, however, the scope has evolved to include a number of other methods for neurochemical detection that range from single-cell fluorescence in vitro and in vivo in animal models to whole-brain imaging in humans. Overall, MMiN provides a unique forum for introducing new developments in neurochemical detection, as well as for reporting exciting neurobiological insights provided by established and novel methods. This Viewpoint includes a brief history of the meeting, factors that have contributed its evolution, and some highlights of MMiN 2016. PMID:28169519

Monitoring Molecules in Neuroscience Then and Now.

PubMed

Rice, Margaret E

2017-02-15

The 16th International Conference on Monitoring Molecules in Neuroscience (MMiN) was held in Gothenburg, Sweden in late spring 2016. This conference originated as a methods meeting focused on in vivo voltammetric techniques and microdialysis. Over time, however, the scope has evolved to include a number of other methods for neurochemical detection that range from single-cell fluorescence in vitro and in vivo in animal models to whole-brain imaging in humans. Overall, MMiN provides a unique forum for introducing new developments in neurochemical detection, as well as for reporting exciting neurobiological insights provided by established and novel methods. This Viewpoint includes a brief history of the meeting, factors that have contributed its evolution, and some highlights of MMiN 2016.

Polymer electro-optic waveguide devices: Low-loss etchless fabrication techniques and passive-to-active integration

NASA Astrophysics Data System (ADS)

Geary, Kevin

The development of high-frequency polymer electro-optic modulators has seen steady and significant progress in recent years, yet applications of these promising materials to more complicated integrated optic structures and arrays of devices have been limited primarily due to high optical waveguide loss characteristics. This is unfortunate since a major advantage of polymers as photonic materials is their compatibility with photolithographic processing of large components. In this Dissertation, etchless waveguide writing techniques are presented in order to improve the overall optical insertion loss of electro-optic polymer waveguide devices. These techniques include poling-induced writing, stress-induced waveguide writing, and photobleaching. Using these waveguide writing mechanisms, we have demonstrated straight waveguides, phase modulators, Mach-Zehnder intensity modulators, variable optical attenuators, and multimode interference (MMI) power splitters, all with improved loss characteristics over their etched rib waveguide counterparts. Ultimately, the insertion loss of an integrated optic device is limited by the actual material loss of the core waveguide material. In this Dissertation, passive-to-active polymer waveguide transitions are proposed to circumvent this problem. These transitions are compact, in-plane, self-aligned, and require no tapering of any physical dimensions of the waveguides. By utilizing both the time-dependent and intensity-dependent photobleaching characteristics of electro-optic polymer materials, adiabatic refractive index tapers can be seamlessly coupled to in-plane butt couple transitions, resulting in losses as low as 0.1 dB per interface. By integrating passive polymer planar lightwave circuits with the high-speed phase shifting capability of electro-optic polymers, active wideband photonic devices of increased size and complexity can be realized. Optical fiber-to-device coupling can also result in significant contributions to the overall insertion loss of an integrated electro-optic polymer device. In this Dissertation, we leverage the photobleached refractive index taper component of our proposed passive-to-active polymer waveguide transitions in order to realize a two-dimensional optical mode transformer for improved overall fiber-to-device coupling of electro-optic polymer waveguide devices.

Displacement sensing based on modal interference in polymer optical fibers with partially applied strain

NASA Astrophysics Data System (ADS)

Mizuno, Yosuke; Hagiwara, Sonoko; Kawa, Tomohito; Lee, Heeyoung; Nakamura, Kentaro

2018-05-01

Strain sensing based on modal interference in multimode fibers (MMFs) has been extensively studied, but no experimental or theoretical reports have been given as to how the system works when strain is applied not to the whole MMF but only to part of the MMF. Here, using a perfluorinated graded-index polymer optical fiber as the MMF, we investigate the strain sensing characteristics of this type of sensor when strain is partially applied to fiber sections with different lengths. The strain sensitivity dependence on the length of the strained section reveals that this strain sensor actually behaves as a displacement sensor.

Fiber-Optic Linear Displacement Sensor Based On Matched Interference Filters

NASA Astrophysics Data System (ADS)

Fuhr, Peter L.; Feener, Heidi C.; Spillman, William B.

1990-02-01

A fiber optic linear displacement sensor has been developed in which a pair of matched interference filters are used to encode linear position on a broadband optical signal as relative intensity variations. As the filters are displaced, the optical beam illuminates varying amounts of each filter. Determination of the relative intensities at each filter pairs' passband is based on measurements acquired with matching filters and photodetectors. Source power variation induced errors are minimized by basing determination of linear position on signal Visibility. A theoretical prediction of the sensor's performance is developed and compared with experiments performed in the near IR spectral region using large core multimode optical fiber.

Transition from Propagating Polariton Solitons to a Standing Wave Condensate Induced by Interactions

NASA Astrophysics Data System (ADS)

Sich, M.; Chana, J. K.; Egorov, O. A.; Sigurdsson, H.; Shelykh, I. A.; Skryabin, D. V.; Walker, P. M.; Clarke, E.; Royall, B.; Skolnick, M. S.; Krizhanovskii, D. N.

2018-04-01

We explore phase transitions of polariton wave packets, first, to a soliton and then to a standing wave polariton condensate in a multimode microwire system, mediated by nonlinear polariton interactions. At low excitation density, we observe ballistic propagation of the multimode polariton wave packets arising from the interference between different transverse modes. With increasing excitation density, the wave packets transform into single-mode bright solitons due to effects of both intermodal and intramodal polariton-polariton scattering. Further increase of the excitation density increases thermalization speed, leading to relaxation of the polariton density from a solitonic spectrum distribution in momentum space down to low momenta, with the resultant formation of a nonequilibrium condensate manifested by a standing wave pattern across the whole sample.

Transition from Propagating Polariton Solitons to a Standing Wave Condensate Induced by Interactions.

PubMed

Sich, M; Chana, J K; Egorov, O A; Sigurdsson, H; Shelykh, I A; Skryabin, D V; Walker, P M; Clarke, E; Royall, B; Skolnick, M S; Krizhanovskii, D N

2018-04-20

We explore phase transitions of polariton wave packets, first, to a soliton and then to a standing wave polariton condensate in a multimode microwire system, mediated by nonlinear polariton interactions. At low excitation density, we observe ballistic propagation of the multimode polariton wave packets arising from the interference between different transverse modes. With increasing excitation density, the wave packets transform into single-mode bright solitons due to effects of both intermodal and intramodal polariton-polariton scattering. Further increase of the excitation density increases thermalization speed, leading to relaxation of the polariton density from a solitonic spectrum distribution in momentum space down to low momenta, with the resultant formation of a nonequilibrium condensate manifested by a standing wave pattern across the whole sample.

TDRSS multimode transponder program. Phase 2: Equipment development

NASA Technical Reports Server (NTRS)

Cnossen, R. S.

1974-01-01

This report contains a complete description of the TDRS Multimode Transponder and its associated ground support equipment. The transponder will demonstrate candidate modulation techniques to provide the required information for the design of an eventual VHF/UHF transponder suitable for installation in a user satellite, capable of operating as part of a Tracking and Data Relay Satellite (TDRS) systems. Use of geosynchronous TDRS which can serve both low data rate users at VHF and high data rate users at other frequencies has been considered. The effects of radio frequency interference from the earth and of multipath propagation due to reflections from the earth are expected to pose problems for the TDRS system at VHF. Investigations have suggested several modulation techniques that offer promise to overcome these problems.

Temperature- and phase-independent lateral force sensor based on a core-offset multi-mode fiber interferometer.

PubMed

Dong, Bo; Zhou, Da-Peng; Wei, Li; Liu, Wing-Ki; Lit, John W Y

2008-11-10

A novel lateral force sensor based on a core-offset multi-mode fiber (MMF) interferometer is reported. High extinction ratio can be obtained by misaligning a fused cross section between the single-mode fiber (SMF) and MMF. With the variation of the lateral force applied to a short section of the MMF, the extinction ratio changes while the interference phase remains almost constant. The change of the extinction ratio is independent of temperature variations. The proposed force sensor has the advantages of temperature- and phase-independency, high extinction ratio sensitivity, good repeatability, low cost, and simple structure. Moreover, the core-offset MMF interferometer is expected to have applications in fiber filters and tunable phase-independent attenuators.

Multilayered photonic integration on SOI platform using waveguide-based bridge structure

NASA Astrophysics Data System (ADS)

Majumder, Saikat; Chakraborty, Rajib

2018-06-01

A waveguide based structure on silicon on insulator platform is proposed for vertical integration in photonic integrated circuits. The structure consists of two multimode interference couplers connected by a single mode (SM) section which can act as a bridge over any other underlying device. Two more SM sections acts as input and output of the first and second multimode couplers respectively. Potential application of this structure is in multilayered photonic links. It is shown that the efficiency of the structure can be improved by making some design modifications. The entire simulation is done using effective-index based matrix method. The feature size chosen are comparable to waveguides fabricated previously so as to fabricate the proposed structure easily.

Hepatoprotective and Antioxidant Effect of Mangifera Indica Leaf Extracts against Mercuric Chloride-induced Liver Toxicity in Mice.

PubMed

Karuppanan, Muthupillai; Krishnan, Manigandan; Padarthi, Pavankumar; Namasivayam, Elangovan

2014-01-01

To explore the antioxidant and hepatoprotective effect of ethanolic Mangifera indica (EMI) and methanolic Mangifera indica (MMI) leaf extracts in mercuric chloride (HgCl 2 ) induced toxicity in Swiss albino mice. Toxicity in mice was induced with HgCl 2 (5.0 mg/kg, i.p.), followed by oral intervention with EMI and MMI extracts (25 mg and 50 mg/kg. body wt.) for 30 days. The extent of liver damage was assessed from the extents of histopathological, morphological, antioxidant and liver enzymes. Mercuric chloride-induced mice showed an increased cellular damage whereas leaf extracts of EMI and MMI-treated mice showed recovery of damaged hepatocytes. Mercuric chloride intoxicated mice exhibited a significant (p < 0.05) elevation in the liver enzymes (Aspartate amino transferase and Alanine amino transferase) and gradual decline in the cellular radical scavenging enzyme levels (Catalase, Glutathione-s-transferase and Glutathione peroxidase. The combined treatment with EMI and MMI leaf extracts significantly (p < 0.05) reversed these parameters. However, the effects of MMI leaf extract (50 mg/kg) were superior to those of EMI- treated mice possibly due to its potent radical scavenging property. These results suggest that oral supplementation of Mangifera indica extract remarkably reduces hepatotoxicity in mice possibly through its antioxidant potentials. How to cite this article: Karuppanan M, Krishnan M, Padarthi P, Namasivayam E. Hepatoprotec-tive and Antioxidant Effect of Mangifera Indica Leaf Extracts against Mercuric Chloride-induced Liver Toxicity in Mice. Euroasian J Hepato-Gastroenterol 2014;4(1):18-24.

Hepatoprotective and Antioxidant Effect of Mangifera Indica Leaf Extracts against Mercuric Chloride-induced Liver Toxicity in Mice

PubMed Central

Karuppanan, Muthupillai; Krishnan, Manigandan; Padarthi, Pavankumar

2014-01-01

ABSTRACT Background To explore the antioxidant and hepatoprotective effect of ethanolic Mangifera indica (EMI) and methanolic Mangifera indica (MMI) leaf extracts in mercuric chloride (HgCl2) induced toxicity in Swiss albino mice. Materials and methods Toxicity in mice was induced with HgCl2 (5.0 mg/kg, i.p.), followed by oral intervention with EMI and MMI extracts (25 mg and 50 mg/kg. body wt.) for 30 days. Results and discussion The extent of liver damage was assessed from the extents of histopathological, morphological, antioxidant and liver enzymes. Mercuric chloride-induced mice showed an increased cellular damage whereas leaf extracts of EMI and MMI-treated mice showed recovery of damaged hepatocytes. Mercuric chloride intoxicated mice exhibited a significant (p < 0.05) elevation in the liver enzymes (Aspartate amino transferase and Alanine amino transferase) and gradual decline in the cellular radical scavenging enzyme levels (Catalase, Glutathione-s-transferase and Glutathione peroxidase. The combined treatment with EMI and MMI leaf extracts significantly (p < 0.05) reversed these parameters. However, the effects of MMI leaf extract (50 mg/kg) were superior to those of EMI- treated mice possibly due to its potent radical scavenging property. These results suggest that oral supplementation of Mangifera indica extract remarkably reduces hepatotoxicity in mice possibly through its antioxidant potentials. How to cite this article: Karuppanan M, Krishnan M, Padarthi P, Namasivayam E. Hepatoprotec-tive and Antioxidant Effect of Mangifera Indica Leaf Extracts against Mercuric Chloride-induced Liver Toxicity in Mice. Euroasian J Hepato-Gastroenterol 2014;4(1):18-24. PMID:29264314

[Predictive model based multimetric index of macroinvertebrates for river health assessment].

PubMed

Chen, Kai; Yu, Hai Yan; Zhang, Ji Wei; Wang, Bei Xin; Chen, Qiu Wen

2017-06-18

Improving the stability of integrity of biotic index (IBI; i.e., multi-metric indices, MMI) across temporal and spatial scales is one of the most important issues in water ecosystem integrity bioassessment and water environment management. Using datasets of field-based macroinvertebrate and physicochemical variables and GIS-based natural predictors (e.g., geomorphology and climate) and land use variables collected at 227 river sites from 2004 to 2011 across the Zhejiang Province, China, we used random forests (RF) to adjust the effects of natural variations at temporal and spatial scales on macroinvertebrate metrics. We then developed natural variations adjusted (predictive) and unadjusted (null) MMIs and compared performance between them. The core me-trics selected for predictive and null MMIs were different from each other, and natural variations within core metrics in predictive MMI explained by RF models ranged between 11.4% and 61.2%. The predictive MMI was more precise and accurate, but less responsive and sensitive than null MMI. The multivariate nearest-neighbor test determined that 9 test sites and 1 most degraded site were flagged outside of the environmental space of the reference site network. We found that combination of predictive MMI developed by using predictive model and the nearest-neighbor test performed best and decreased risks of inferring type I (designating a water body as being in poor biological condition, when it was actually in good condition) and type II (designating a water body as being in good biological condition, when it was actually in poor condition) errors. Our results provided an effective method to improve the stability and performance of integrity of biotic index.

Experimental generalized quantum suppression law in Sylvester interferometers

NASA Astrophysics Data System (ADS)

Viggianiello, Niko; Flamini, Fulvio; Innocenti, Luca; Cozzolino, Daniele; Bentivegna, Marco; Spagnolo, Nicolò; Crespi, Andrea; Brod, Daniel J.; Galvão, Ernesto F.; Osellame, Roberto; Sciarrino, Fabio

2018-03-01

Photonic interference is a key quantum resource for optical quantum computation, and in particular for so-called boson sampling devices. In interferometers with certain symmetries, genuine multiphoton quantum interference effectively suppresses certain sets of events, as in the original Hong–Ou–Mandel effect. Recently, it was shown that some classical and semi-classical models could be ruled out by identifying such suppressions in Fourier interferometers. Here we propose a suppression law suitable for random-input experiments in multimode Sylvester interferometers, and verify it experimentally using 4- and 8-mode integrated interferometers. The observed suppression occurs for a much larger fraction of input–output combinations than what is observed in Fourier interferometers of the same size, and could be relevant to certification of boson sampling machines and other experiments relying on bosonic interference, such as quantum simulation and quantum metrology.

Molecular responses of cells to 2-mercapto-1-methylimidazole gold nanoparticles (AuNPs)-mmi: investigations of histone methylation changes

NASA Astrophysics Data System (ADS)

Polverino, Arianna; Longo, Angela; Donizetti, Aldo; Drongitis, Denise; Frucci, Maria; Schiavo, Loredana; Carotenuto, Gianfranco; Nicolais, Luigi; Piscopo, Marina; Vitale, Emilia; Fucci, Laura

2014-07-01

While nanomedicine has an enormous potential to improve the precision of specific therapy, the ability to efficiently deliver these materials to regions of disease in vivo remains limited. In this study, we describe analyses of (AuNPs)-mmi cellular intake via fluorescence microscopy and its effects on H3K4 and H3K9 histone dimethylation. Specifically, we studied the level of H3K4 dimethylation in serving the role of an epigenetic marker of euchromatin, and of H3K9 dimethylation as a marker of transcriptional repression in four different cell lines. We analyzed histone di-methyl-H3K4 and di-methyl-H3K9 using either variable concentrations of nanoparticles or variable time points after cellular uptake. The observed methylation effects decreased consistently with decreasing (AuNPs)-mmi concentrations. Fluorescent microscopy and a binarization algorithm based on a thresholding process with RGB input images demonstrated the continued presence of (AuNPs)-mmi in cells at the lowest concentration used. Furthermore, our results show that the treated cell line used is able to rescue the untreated cell phenotype.

Management of hyperthyroidism during pregnancy and lactation.

PubMed

Azizi, Fereidoun; Amouzegar, Atieh

2011-06-01

Poorly treated or untreated maternal overt hyperthyroidism may affect pregnancy outcome. Fetal and neonatal hypo- or hyper-thyroidism and neonatal central hypothyroidism may complicate health issues during intrauterine and neonatal periods. To review articles related to appropriate management of hyperthyroidism during pregnancy and lactation. A literature review was performed using MEDLINE with the terms 'hyperthyroidism and pregnancy', 'antithyroid drugs and pregnancy', 'radioiodine and pregnancy', 'hyperthyroidism and lactation', and 'antithyroid drugs and lactation', both separately and in conjunction with the terms 'fetus' and 'maternal.' Antithyroid drugs are the main therapy for maternal hyperthyroidism. Both methimazole (MMI) and propylthiouracil (PTU) may be used during pregnancy; however, PTU is preferred in the first trimester and should be replaced by MMI after this trimester. Choanal and esophageal atresia of fetus in MMI-treated and maternal hepatotoxicity in PTU-treated pregnancies are of utmost concern. Maintaining free thyroxine concentration in the upper one-third of each trimester-specific reference interval denotes success of therapy. MMI is the mainstay of the treatment of post partum hyperthyroidism, in particular during lactation. Management of hyperthyroidism during pregnancy and lactation requires special considerations and should be carefully implemented to avoid any adverse effects on the mother, fetus, and neonate.

Central nervous system vasculitis after starting methimazole in a woman with Graves' disease.

PubMed

Tripodi, Pier Francesco; Ruggeri, Rosaria M; Campennì, Alfredo; Cucinotta, Mariapaola; Mirto, Angela; Lo Gullo, Renato; Baldari, Sergio; Trimarchi, Francesco; Cucinotta, Domenico; Russo, Giuseppina T

2008-09-01

Graves' disease (GD), a prototypical autoimmune disorder, is associated with other autoimmune diseases, including vasculitis. Antithyroid drugs, despite their postulated immunosuppressive effects, may cause several autoimmune disorders. Here we describe the first patient with central nervous system (CNS) vasculitis that developed shortly after the start of methimazole (MMI) treatment for GD. CNS vasculitis was suspected on the basis of the clinical features and neurologic examination, showing a reinforcement of deep reflexes, especially of the left knee and Achilles reflexes. The diagnosis was confirmed by a brain magnetic resonance imaging (MRI), which showed some hyperintensive spots in the subcortical substantia alba and in the parietal area bilaterally, and by a single-photon emission computed tomography (SPECT) imaging, which showed a nonhomogenous distribution of the blood flow in the brain, with a reduced perfusion on the left side of the frontotemporal and parietal regions, and on the right side of the frontotemporal area. MMI was stopped before total thyroidectomy, and symptoms resolved in the next 5 weeks. Six months after MMI was stopped, the brain MRI and SPECT had become normal. To our knowledge, this is the first report of CNS vasculitis related to MMI therapy.

A new macroseismic intensity prediction equation and magnitude estimates of the 1811-1812 New Madrid and 1886 Charleston, South Carolina, earthquakes

NASA Astrophysics Data System (ADS)

Boyd, O. S.; Cramer, C. H.

2013-12-01

We develop an intensity prediction equation (IPE) for the Central and Eastern United States, explore differences between modified Mercalli intensities (MMI) and community internet intensities (CII) and the propensity for reporting, and estimate the moment magnitudes of the 1811-1812 New Madrid, MO, and 1886 Charleston, SC, earthquakes. We constrain the study with North American census data, the National Oceanic and Atmospheric Administration MMI dataset (responses between 1924 and 1985), and the USGS ';Did You Feel It?' CII dataset (responses between June, 2000 and August, 2012). The combined intensity dataset has more than 500,000 felt reports for 517 earthquakes with magnitudes between 2.5 and 7.2. The IPE has the basic form, MMI=c1+c2M+c3exp(λ)+c4λ. where M is moment magnitude and λ is mean log hypocentral distance. Previous IPEs use a limited dataset of MMI, do not differentiate between MMI and CII data in the CEUS, nor account for spatial variations in population. These factors can have an impact at all magnitudes, especially the last factor at large magnitudes and small intensities where the population drops to zero in the Atlantic Ocean and Gulf of Mexico. We assume that the number of reports of a given intensity have hypocentral distances that are log-normally distributed, the distribution of which is modulated by population and the propensity for individuals to report their experience. We do not account for variations in stress drop, regional variations in Q, or distance-dependent geometrical spreading. We simulate the distribution of reports of a given intensity accounting for population and use a grid search method to solve for the fraction of population to report the intensity, the standard deviation of the log-normal distribution and the mean log hypocentral distance, which appears in the above equation. We find that lower intensities, both CII and MMI, are less likely to be reported than greater intensities. Further, there are strong spatial variations in the level of CII reporting. For example, large metropolitan areas appear to have a lower level of reporting relative to rural areas. In general, we find that intensities decrease with increasing distance and decreasing magnitude, as expected. Coefficients for the IPE are c1=1.98×0.13 c2=1.76×0.02 c3=-0.0027×0.0004, and c4=-1.26×0.03. We find significant differences in mean log hypocentral distance between MMI- and CII-based reporting, particularly at smaller mean log distance and higher intensity. Values of mean log distance for CII at high intensity tend to be smaller than for MMI at the same value of intensity. The new IPE leads to magnitude estimates for the 1811-1812 New Madrid earthquakes that are within the broad range of those determined previously. Using three MMI datasets for the New Madrid mainshocks, the new relation results in estimates for the moment magnitudes of the December 16th, 1811, January 23rd, 1812, and February 7th, 1812 mainshocks and December 16th dawn aftershock of 7.1¬¬-7.4, 7.2, 7.5-7.7, and 6.7-7.2, respectively, with a magnitude uncertainty of about ×0.4 units. We estimate a magnitude of 7.0×0.3 for the 1886 Charleston, SC earthquake.

Quaternary Basalts in Grand Canyon: Correlation of Flows Using Lidar, 40Ar/39Ar Dating, Geochemical Correlation, Neotectonic Studies, and History of Lava Dams

NASA Astrophysics Data System (ADS)

Crow, R. S.; Karlstrom, K. E.; McIntosh, W. C.; Dunbar, N. W.; Peters, L.; Raucci, J.; Umhoefer, P. J.

2005-12-01

In western Grand Canyon, basalts flowed into the already existing canyon from at least 719 ka to present. These basalts provide a key for deciphering Quaternary rates of incision, neotectonic slip rates on the Toroweap and Hurricane faults, and the history of lava dams. Stratigraphy and/or inset relationships between basalt flows is exceedingly complex because of the multiple eruptions, extreme topography, long transport distance, and incomplete preservation. Correlation of flows using 40Ar/39Ar dating, LIDAR data, orthophotography, and geochemical analysis, as well as structural and geomorphic studies, lead to a working hypothesis for four major episodes of basaltic eruptive activity. From 719 to 484 Ma major volcanoes erupted near the Toroweap fault zone. The extent of the remnants and presence of 527 ka dikes indicates that cones where built within Grand Canyon during this phase. These flows had the longest outflow (719 ka flow at mile 246). At 349 to 296 ka flows seem to have entered the canyon at Whitmore Wash, north rim. The two remaining episodes, dated at 199-193 ka and 109-97 ka are interpreted to have cascaded into the canyon at and upstream from Whitmore Wash. LIDAR/orthophotography interpretation of the tops and bottoms of the flows and geochemical analysis of phenocrysts aid in correlation of undated remnants and reconstructing the shape of volcanic edifices. Flows dated from 720-450 ka include Prospect, Black Ledge, D-Dam, and Toroweap flows, thus Black Ledge flows are considerably older than previously thought. The 350 to 300 flows include Whitmore, Layered Diabase, Massive Diabase, and 177-mile flows. All the dated 200 and 100 ka flows have been called Grey Ledge flows, suggesting that the Grey Ledge represents two distinct events. Basalt data indicate an interaction of canyon incision and Quaternary fault slip. Bedrock incision rates are calculated using dated flows that overly bedrock straths. Rates vary across active faults indicating fault dampening of apparent river incision rates. Incision rates for eastern Grand Canyon are 127 m/my over 387 ka. Similar rates just east of the Toroweap faults (136 m/my over 349 ka and 153 m/my over 484 ka) suggest that a fairly uniform regional rate of ~ 140 m/my can be considered the average rate for Grand Canyon incision east of the Toroweap fault. This is subequal to the sum of apparent incision rate just below the Toroweap fault (56 m/my over 484 ka) plus fault slip rate (90 m/my over 550 ka). Similarly, apparent incision rates below the Hurricane fault (66 m/my over 527 ka and 76 m/my over 604 ka, near Granite Park) plus fault slip rate (~80±20 m/my over 185 ka) is subequal to the far field incision rate. Accumulating data suggests that apparent incision rates are lowest adjacent to faults in the hanging wall and highest adjacent to faults in the footwall, with rates varying systematically across fault blocks. This suggests that faulting is taking place by domino rotation of blocks bounded by normal faults with mild listric character. These new empirical data help constrain physical models for Quaternary fault slip across the active Colorado Plateau- Basin and Range bounding structures.

The reliability and validity of multiple mini interviews (MMIs) in values based recruitment to nursing, midwifery and paramedic practice programmes: Findings from an evaluation study.

PubMed

Callwood, Alison; Cooke, Debbie; Bolger, Sarah; Lemanska, Agnieszka; Allan, Helen

2018-01-01

Universities in the United Kingdom (UK) are required to incorporate values based recruitment (VBR) into their healthcare student selection processes. This reflects an international drive to strengthen the quality of healthcare service provision. This paper presents novel findings in relation to the reliability and predictive validity of multiple mini interviews (MMIs); one approach to VBR widely being employed by universities. To examine the reliability (internal consistency) and predictive validity of MMIs using end of Year One practice outcomes of under-graduate pre-registration adult, child, mental health nursing, midwifery and paramedic practice students. Cross-discipline evaluation study. One university in the United Kingdom. Data were collected in two streams: applicants to A) The September 2014 and 2015 Midwifery Studies programmes; B) September 2015 adult; Child and Mental Health Nursing and Paramedic Practice programmes. Fifty-seven midwifery students commenced their programme in 2014 and 69 in 2015; 47 and 54 agreed to participate and completed Year One respectively. 333 healthcare students commenced their programmes in September 2015. Of these, 281 agreed to participate and completed their first year (180 adult, 33 child and 34 mental health nursing and 34 paramedic practice students). Stream A featured a seven station four-minute model with one interviewer at each station and in Stream B a six station model was employed. Cronbach's alpha was used to assess MMI station internal consistency and Pearson's moment correlation co-efficient to explore associations between participants' admission MMI score and end of Year one clinical practice outcomes (OSCE and mentor grading). Stream A: Significant correlations are reported between midwifery applicant's MMI scores and end of Year One practice outcomes. A multivariate linear regression model demonstrated that MMI score significantly predicted end of Year One practice outcomes controlling for age and academic entry level: coefficients 0.195 (p=0.002) and 0.116 (p=0.002) for OSCE and mentor grading respectively. In Stream B no significant correlations were found between MMI score and practice outcomes measured by mentor grading. Internal consistency for each MMI station was 'excellent' with values ranging from 0.966-0.974 across Streams A and B. This novel, cross-discipline study shows that MMIs are reliable VBR tools which have predictive validity when a seven station model is used. These data are important given the current international use of different MMI models in healthcare student selection processes. Copyright © 2017. Published by Elsevier Ltd.

Nonlinear Structural Health Monitoring of the Responsive Space Satellite Systems Using Magneto Elastic Active Sensors (MEAS)

DTIC Science & Technology

2011-11-30

detection of fatigue damage at early stage, well before onset of fracture and crack development. Analytical and numerical models of MEAS and MMI are...stage, well before onset of fracture and crack development. Analytical and numerical models of MEAS and MMI are suggested. Finally, MEAS capability...47  2.4.1  Far-Field Crack Detection

Intensity distribution and isoseismal maps for the Nisqually, Washington, earthquake of 28 February 2001

USGS Publications Warehouse

Dewey, James W.; Hopper, Margaret G.; Wald, David J.; Quitoriano, Vincent; Adams, Elizabeth R.

2002-01-01

We present isoseismal maps, macroseismic intensities, and community summaries of damage for the MW=6.8 Nisqually, Washington, earthquake of 28 February, 2001. For many communities, two types of macroseismic intensity are assigned, the traditional U.S. Geological Survey Modified Mercalli Intensities (USGS MMI) and a type of intensity newly introduced with this paper, the USGS Reviewed Community Internet Intensity (RCII). For most communities, the RCII is a reviewed version of the Community Internet Intensity (CII) of Wald and others (1999). For some communities, RCII is assigned from such non-CII sources as press reports, engineering reports, and field reconnaissance observations. We summarize differences between procedures used to assign RCII and USGS MMI, and we show that the two types of intensity are nonetheless very similar for the Nisqually earthquake. We do not see evidence for systematic differences between RCII and USGS MMI that would approach one intensity unit, at any level of shaking, but we document a tendency for the RCII to be slightly lower than MMI in regions of low intensity and slightly higher than MMI in regions of high intensity. The highest RCII calculated for the Nisqually earthquake is 7.6, calculated for zip code 98134, which includes the ?south of downtown? (Sodo) area of Seattle and Harbor Island. By comparison, we assigned a traditional USGS MMI 8 to the Sodo area of Seattle. In all, RCII of 6.5 and higher were assigned to 58 zip-code regions. At the lowest intensities, the Nisqually earthquake was felt over an area of approximately 350,000 square km (approximately 135,000 square miles) in Washington, Oregon, Idaho, Montana, and southern British Columbia, Canada. On the basis of macroseismic effects, we infer that shaking in the southern Puget Sound region was somewhat less for the 2001 Nisqually earthquake than for the Puget Sound earthquake of April 13, 1949, which had nearly the same hypocenter and magnitude. Allowing for differences in hypocenter, shaking in the 2001 earthquake was very similar to that produced by the Puget Sound earthquake of April 25, 1965. First-person accounts of the effects of the 2001 earthquake on individual households are given for some communities.

Do Multiple Mini-Interview and Traditional Interview Scores Differ in Their Associations With Acceptance Offers Within and Across Five California Medical Schools?

PubMed

Jerant, Anthony; Henderson, Mark C; Griffin, Erin; Hall, Theodore R; Kelly, Carolyn J; Peterson, Ellena M; Wofsy, David; Franks, Peter

2018-03-20

In single-school studies, multiple mini-interview (MMI) and traditional interview (TI) scores are associated with acceptance offers. Unexamined is whether scores at one school are associated with acceptance at other schools; such analyses would mitigate single-school design biases and better estimate how well interviews capture desired applicant attributes. Using data from the five California Longitudinal Evaluation of Admissions Practices (CA-LEAP) public medical schools, the authors examined associations of MMI and TI scores with acceptance offers within and across schools. The analyses included applicants who interviewed at ≥1 CA-LEAP school during the 2011-2013 admissions cycles, when three CA-LEAP schools employed TIs and two employed MMIs. Interview scores were standardized (z-scores: mean = 0, SD = 1) and associations with acceptance offers were examined within and across schools in analyses stratified by school, adjusting for applicant sociodemographics, academic metrics, year, and total number of interviews. Of 4,993 applicants interviewed, 428 (8.6%) interviewed at both MMI schools, 681 (13.6%) at ≥2 TI schools, and 1,327 (26.6%) at ≥1 MMI and ≥1 TI school. For each school, acceptance was associated with interview score at that school and also with interview scores at the other four schools. Cross-school associations of MMI versus TI scores with acceptance did not differ statistically. Interview score at a given CA-LEAP school was associated with acceptance at the other four schools, with no significant differences in associations for MMIs versus TIs. The findings suggest both MMIs and TIs captured attributes valued by admissions teams across CA-LEAP schools.

Dose-responses for mortality from cerebrovascular and heart diseases in atomic bomb survivors: 1950-2003.

PubMed

Schöllnberger, Helmut; Eidemüller, Markus; Cullings, Harry M; Simonetto, Cristoforo; Neff, Frauke; Kaiser, Jan Christian

2018-03-01

The scientific community faces important discussions on the validity of the linear no-threshold (LNT) model for radiation-associated cardiovascular diseases at low and moderate doses. In the present study, mortalities from cerebrovascular diseases (CeVD) and heart diseases from the latest data on atomic bomb survivors were analyzed. The analysis was performed with several radio-biologically motivated linear and nonlinear dose-response models. For each detrimental health outcome one set of models was identified that all fitted the data about equally well. This set was used for multi-model inference (MMI), a statistical method of superposing different models to allow risk estimates to be based on several plausible dose-response models rather than just relying on a single model of choice. MMI provides a more accurate determination of the dose response and a more comprehensive characterization of uncertainties. It was found that for CeVD, the dose-response curve from MMI is located below the linear no-threshold model at low and medium doses (0-1.4 Gy). At higher doses MMI predicts a higher risk compared to the LNT model. A sublinear dose-response was also found for heart diseases (0-3 Gy). The analyses provide no conclusive answer to the question whether there is a radiation risk below 0.75 Gy for CeVD and 2.6 Gy for heart diseases. MMI suggests that the dose-response curves for CeVD and heart diseases in the Lifespan Study are sublinear at low and moderate doses. This has relevance for radiotherapy treatment planning and for international radiation protection practices in general.

Single voxel magnetic resonance spectroscopy at 3 Tesla in a memory disorders clinic: early right hippocampal NAA/Cr loss in mildly impaired subjects.

PubMed

Caserta, Maria T; Ragin, Ann; Hermida, Adriana P; Ahrens, R John; Wise, Leon

2008-11-30

In this study, we use magnetic resonance spectroscopy (MRS) at 3 Tesla to measure N-acetyl aspartate (NAA), myo-inositol (mI) and choline (Cho) to creatine (Cr) ratios in R (right) and L (left) hippocampi (H) in 8 mildly memory impaired (MMI), 6 probable Alzheimer's Disease (PRAD), and 17 control subjects. NAA/Cr was significantly reduced in the RH in the MMI group and bilaterally in the PRAD group vs. controls. No other metabolite differences were noted between the three groups. Five MMI subjects have converted to PRAD in follow-up. These findings suggest that RH NAA/Cr ratios measured at 3 Tesla may be a sensitive marker of future progression to dementia in a clinically defined population with isolated memory complaints.

Discrimination of dipicolinic acid and its interferents by femtosecond coherent Raman spectroscopy

NASA Astrophysics Data System (ADS)

Huang, Yu; Dogariu, Arthur; Avitzour, Yoav; Murawski, Robert K.; Pestov, Dmitry; Zhi, Miaochan; Sokolov, Alexei V.; Scully, Marlan O.

2006-12-01

Measurements of the beat frequencies between vibrational modes of dipicolinic acid (DPA) and a series of other molecules (interferents) are presented. The results were obtained from femtosecond time-resolved coherent Raman scattering, and the vibrational level spacings were determined from a Fourier transform of the signal versus probe pulse delay. The entire spectrum of the generated signal is recorded in order to demonstrate multimode excitation and to explain the variety of qualitatively different traces that can be obtained for the same molecule. Since the spectral signature of DPA is unique enough to be used for identification purposes, this technique has the potential to detect hazardous bacterial species, such as anthrax spores.

Optical fiber curvature sensor based on MMF-SCF-MMF structure

NASA Astrophysics Data System (ADS)

Wang, Qi; Liu, Yu

2018-07-01

A sensitive curvature sensor based on MMF-SCF-MMF (MMF: multimode fiber; SCF: seven core fiber) structure is proposed. The multimode fiber (MMF) are used to improve the light coupling efficiency between the input singlemode fiber (SMF) and the seven-core fiber (SCF), and the seven-core fiber is used as the main element for curvature measurement. Experimental results show that the best curvature sensitivity reaches 41.46453 nm/m-1 in the range of 0.094 m-1-0.567 m-1. The temperature sensitivity is up to 59.02 pm/°C in the range of 20 °C-55 °C. The optical curvature sensors are widely used for buildings structure health monitoring and mechanical engineering due to the advantages of compact structure, anti-electromagnetic interference, and low cost.

TDRS multimode transponder program. Phase 1: Design

NASA Technical Reports Server (NTRS)

Cnossen, R. S.

1972-01-01

The use of geosynchronous tracking and data relay satellites (TDRS) which can serve both low data rate users at VHF and high data rate users at other frequencies is considered. The effects of radio frequency interference from the earth and of multipath propagation due to reflections from the earth are expected to pose problems for the TDRS system at VHF. Investigations suggest several modulation techniques that offer promise to overcome these problems. This report provides a complete design of a VHF/UHF multimode transponder and its associated ground support equipment. The transponder is designed for installation aboard an aircraft and will demonstrate candidate modulation techniques to provide the required information for the design of an eventual VHF/UHF transponder suitable for installation in a user satellite, capable of operating as part of a TDRS system.

Nonclassicality Criteria in Multiport Interferometry

NASA Astrophysics Data System (ADS)

Rigovacca, L.; Di Franco, C.; Metcalf, B. J.; Walmsley, I. A.; Kim, M. S.

2016-11-01

Interference lies at the heart of the behavior of classical and quantum light. It is thus crucial to understand the boundaries between which interference patterns can be explained by a classical electromagnetic description of light and which, on the other hand, can only be understood with a proper quantum mechanical approach. While the case of two-mode interference has received a lot of attention, the multimode case has not yet been fully explored. Here we study a general scenario of intensity interferometry: we derive a bound on the average correlations between pairs of output intensities for the classical wavelike model of light, and we show how it can be violated in a quantum framework. As a consequence, this violation acts as a nonclassicality witness, able to detect the presence of sources with sub-Poissonian photon-number statistics. We also develop a criterion that can certify the impossibility of dividing a given interferometer into two independent subblocks.

Experimental statistical signature of many-body quantum interference

NASA Astrophysics Data System (ADS)

Giordani, Taira; Flamini, Fulvio; Pompili, Matteo; Viggianiello, Niko; Spagnolo, Nicolò; Crespi, Andrea; Osellame, Roberto; Wiebe, Nathan; Walschaers, Mattia; Buchleitner, Andreas; Sciarrino, Fabio

2018-03-01

Multi-particle interference is an essential ingredient for fundamental quantum mechanics phenomena and for quantum information processing to provide a computational advantage, as recently emphasized by boson sampling experiments. Hence, developing a reliable and efficient technique to witness its presence is pivotal in achieving the practical implementation of quantum technologies. Here, we experimentally identify genuine many-body quantum interference via a recent efficient protocol, which exploits statistical signatures at the output of a multimode quantum device. We successfully apply the test to validate three-photon experiments in an integrated photonic circuit, providing an extensive analysis on the resources required to perform it. Moreover, drawing upon established techniques of machine learning, we show how such tools help to identify the—a priori unknown—optimal features to witness these signatures. Our results provide evidence on the efficacy and feasibility of the method, paving the way for its adoption in large-scale implementations.

Comparing spatial regression to random forests for large ...

EPA Pesticide Factsheets

Environmental data may be “large” due to number of records, number of covariates, or both. Random forests has a reputation for good predictive performance when using many covariates, whereas spatial regression, when using reduced rank methods, has a reputation for good predictive performance when using many records. In this study, we compare these two techniques using a data set containing the macroinvertebrate multimetric index (MMI) at 1859 stream sites with over 200 landscape covariates. Our primary goal is predicting MMI at over 1.1 million perennial stream reaches across the USA. For spatial regression modeling, we develop two new methods to accommodate large data: (1) a procedure that estimates optimal Box-Cox transformations to linearize covariate relationships; and (2) a computationally efficient covariate selection routine that takes into account spatial autocorrelation. We show that our new methods lead to cross-validated performance similar to random forests, but that there is an advantage for spatial regression when quantifying the uncertainty of the predictions. Simulations are used to clarify advantages for each method. This research investigates different approaches for modeling and mapping national stream condition. We use MMI data from the EPA's National Rivers and Streams Assessment and predictors from StreamCat (Hill et al., 2015). Previous studies have focused on modeling the MMI condition classes (i.e., good, fair, and po

Intravenous methimazole in the treatment of refractory hyperthyroidism.

PubMed

Hodak, Steven P; Huang, Caroline; Clarke, Donna; Burman, Kenneth D; Jonklaas, Jacqueline; Janicic-Kharic, Natasa

2006-07-01

Management of a hyperthyroid patient unable to take oral or rectal medication is a difficult clinical problem. The need for an alternative parenteral route of antithyroid medication administration in thyrotoxic patients occurs in certain rare cases, such as emergent gastrointestinal surgery, bowel ileus or obstruction, or severe vomiting and diarrhea. We report a simple and successful protocol for the preparation and use of intravenous methimazole (MMI) for treatment of hyperthyroidism in patients intolerant of orally and rectally administered thionamides. Five hundred milligrams of methimazole USP powder was reconstituted with pH-neutral 0.9% sodium chloride solution to a final volume of 50 mL using aseptic technique, then filtered through a 0.22-microm filter. MMI injection was administered as a slow intravenous push over 2 minutes and followed by a saline flush. A 76-year-old man, intolerant of oral and rectal medications because of an ileus and intractable diarrhea, who developed worsening thyrotoxicosis after an emergent spinal cord decompression, and a 42-year-old man with chronic liver disease and hyperthyroidism, requiring emergent exploratory laparotomy and maintenance of complete bowel rest because of persistent gastrointestinal bleeding were rendered euthyroid using intravenous MMI. Two cases of hyperthyroidism successfully treated with a preparation of intravenous MMI are described.

Individual differences in media multitasking and performance on the n-back.

PubMed

Ralph, Brandon C W; Smilek, Daniel

2017-02-01

A number of studies have recently examined the link between individual differences in media multitasking (using the MMI) and performance on working memory paradigms. However, these studies have yielded mixed results. Here we examine the relation between media multitasking and one particular working memory paradigm-the n-back (2- and 3-back)-improving upon previous research by (a) treating media multitasking as a continuous variable and adopting a correlational approach as well as (b) using a large sample of participants. First, we found that higher scores on the MMI were associated with a greater proportion of omitted trials on both the 2-back and 3-back, indicating that heavier media multitaskers were more disengaged during the n-back. In line with such a claim, heavier media multitaskers were also more likely to confess to responding randomly during various portions of the experiment, and to report media multitasking during the experiment itself. Importantly, when controlling for the relation between MMI scores and omissions, higher scores on the MMI were associated with an increase in false alarms, but not with a change in hits. These findings refine the extant literature on media multitasking and working memory performance (specifically, performance on the n-back), and suggest that media multitasking may be related to the propensity to disengage from ongoing tasks.

Multimodal Spectral Imaging of Cells Using a Transmission Diffraction Grating on a Light Microscope

PubMed Central

Isailovic, Dragan; Xu, Yang; Copus, Tyler; Saraswat, Suraj; Nauli, Surya M.

2011-01-01

A multimodal methodology for spectral imaging of cells is presented. The spectral imaging setup uses a transmission diffraction grating on a light microscope to concurrently record spectral images of cells and cellular organelles by fluorescence, darkfield, brightfield, and differential interference contrast (DIC) spectral microscopy. Initially, the setup was applied for fluorescence spectral imaging of yeast and mammalian cells labeled with multiple fluorophores. Fluorescence signals originating from fluorescently labeled biomolecules in cells were collected through triple or single filter cubes, separated by the grating, and imaged using a charge-coupled device (CCD) camera. Cellular components such as nuclei, cytoskeleton, and mitochondria were spatially separated by the fluorescence spectra of the fluorophores present in them, providing detailed multi-colored spectral images of cells. Additionally, the grating-based spectral microscope enabled measurement of scattering and absorption spectra of unlabeled cells and stained tissue sections using darkfield and brightfield or DIC spectral microscopy, respectively. The presented spectral imaging methodology provides a readily affordable approach for multimodal spectral characterization of biological cells and other specimens. PMID:21639978

MIMO signal progressing with RLSCMA algorithm for multi-mode multi-core optical transmission system

NASA Astrophysics Data System (ADS)

Bi, Yuan; Liu, Bo; Zhang, Li-jia; Xin, Xiang-jun; Zhang, Qi; Wang, Yong-jun; Tian, Qing-hua; Tian, Feng; Mao, Ya-ya

2018-01-01

In the process of transmitting signals of multi-mode multi-core fiber, there will be mode coupling between modes. The mode dispersion will also occur because each mode has different transmission speed in the link. Mode coupling and mode dispersion will cause damage to the useful signal in the transmission link, so the receiver needs to deal received signal with digital signal processing, and compensate the damage in the link. We first analyzes the influence of mode coupling and mode dispersion in the process of transmitting signals of multi-mode multi-core fiber, then presents the relationship between the coupling coefficient and dispersion coefficient. Then we carry out adaptive signal processing with MIMO equalizers based on recursive least squares constant modulus algorithm (RLSCMA). The MIMO equalization algorithm offers adaptive equalization taps according to the degree of crosstalk in cores or modes, which eliminates the interference among different modes and cores in space division multiplexing(SDM) transmission system. The simulation results show that the distorted signals are restored efficiently with fast convergence speed.

Influence of mode-beating pulse on laser-induced plasma

NASA Astrophysics Data System (ADS)

Nishihara, M.; Freund, J. B.; Glumac, N. G.; Elliott, G. S.

2018-04-01

This paper addresses the influence of mode-beating pulse on laser-induced plasma. The second harmonic of a Nd:YAG laser, operated either with the single mode or multimode, was used for non-resonant optical breakdown, and subsequent plasma development was visualized using a streak imaging system. The single mode lasing leads to a stable breakdown location and smooth envelopment of the plasma boundary, while the multimode lasing, with the dominant mode-beating frequency of 500-800 MHz, leads to fluctuations in the breakdown location, a globally modulated plasma surface, and growth of local microstructures at the plasma boundary. The distribution of the local inhomogeneity was measured from the elastic scattering signals on the streak image. The distance between the local structures agreed with the expected wavelength of hydrodynamic instability development due to the interference between the surface excited wave and transmitted wave. A numerical simulation, however, indicates that the local microstructure could also be directly generated at the peaks of the higher harmonic components if the multimode pulse contains up to the eighth harmonic of the fundamental cavity mode.

Multimodal compared to pharmacologic treatments for chronic tension-type headache in adolescents.

PubMed

Przekop, Peter; Przekop, Allison; Haviland, Mark G

2016-10-01

Chronic tension-type headache (CTTH) in children and adolescents is a serious medical condition, with considerable morbidity and few effective, evidence-based treatments. We performed a chart review of 83 adolescents (age range = 13-18 years; 67 girls and 16 boys) diagnosed with CTTH. Two treatment protocols were compared: multimodal (osteopathic manipulative treatments, mindfulness, and qi gong) and pharmacologic (amitriptyline or gabapentin). Four outcomes (headache frequency, pain intensity, general health, and health interference) were assessed at three time points (baseline, 3 months, and 6 months). A fifth outcome, number of bilateral tender points, was recorded at baseline and 6 months. All five were evaluated statistically with a linear mixed model. Although both multimodal and pharmacologic treatments were effective for CTTH (time effects for all measures were significant at p < .001), results from each analysis favored multimodal treatment (the five group by time interaction effects were significant at or below the p < .001 level). Headache frequency in the pharmacologic group, for example, reduced from a monthly average (95% Confidence Interval shown in parentheses) of 23.9 (21.8, 26.0) to 16.4 (14.3, 18.6) and in the multimodal group from 22.3 (20.1, 24.5) to 4.9 (2.6, 7.2) (a substantial group difference). Pain intensity (worst in the last 24 hours, 0-10 scale) was reduced in the pharmacologic group from 6.2 (5.6, 6.9) to 3.4 (2.7, 4.1) and from 6.1 (5.4, 6.8) to 2.0 (1.2, 2.7) in the multimodal group (a less substantial difference). Across the other three assessments, group differences were larger for general health and number of tender points and less so for pain restriction. Multimodal treatment for adolescent CTTH appears to be effective. Randomized controlled trials are needed to confirm these promising results. Copyright © 2015 Elsevier Ltd. All rights reserved.

Single-Fiber Optical Link For Video And Control

NASA Technical Reports Server (NTRS)

Galloway, F. Houston

1993-01-01

Single optical fiber carries control signals to remote television cameras and video signals from cameras. Fiber replaces multiconductor copper cable, with consequent reduction in size. Repeaters not needed. System works with either multimode- or single-mode fiber types. Nonmetallic fiber provides immunity to electromagnetic interference at suboptical frequencies and much less vulnerable to electronic eavesdropping and lightning strikes. Multigigahertz bandwidth more than adequate for high-resolution television signals.

Multimodality Imaging of RNA Interference

PubMed Central

Nayak, Tapas R.; Krasteva, Lazura K.; Cai, Weibo

2013-01-01

The discovery of small interfering RNAs (siRNAs) and their potential to knock down virtually any gene of interest has ushered in a new era of RNA interference (RNAi). Clinical use of RNAi faces severe limitations due to inefficiency delivery of siRNA or short hairpin RNA (shRNA). Many molecular imaging techniques have been adopted in RNAi-related research for evaluation of siRNA/shRNA delivery, biodistribution, pharmacokinetics, and the therapeutic effect. In this review article, we summarize the current status of in vivo imaging of RNAi. The molecular imaging techniques that have been employed include bioluminescence/fluorescence imaging, magnetic resonance imaging/spectroscopy, positron emission tomography, single-photon emission computed tomography, and various combinations of these techniques. Further development of non-invasive imaging strategies for RNAi, not only focusing on the delivery of siRNA/shRNA but also the therapeutic efficacy, is critical for future clinical translation. Rigorous validation will be needed to confirm that biodistribution of the carrier is correlated with that of siRNA/shRNA, since imaging only detects the label (e.g. radioisotopes) but not the gene or carrier themselves. It is also essential to develop multimodality imaging approaches for realizing the full potential of therapeutic RNAi, as no single imaging modality may be sufficient to simultaneously monitor both the gene delivery and silencing effect of RNAi. PMID:23745567

Ultrahigh-sensitive multimode interference-based fiber optic liquid-level sensor realized using illuminating zero-order Bessel-Gauss beam

NASA Astrophysics Data System (ADS)

Saha, Ardhendu; Datta, Arijit; Kaman, Surjit

2018-03-01

A proposal toward the enhancement in the sensitivity of a multimode interference-based fiber optic liquid-level sensor is explored analytically using a zero-order Bessel-Gauss (BG) beam as the input source. The sensor head consists of a suitable length of no-core fiber (NCF) sandwiched between two specialty high-order mode fibers. The coupling efficiency of various order modes inside the sensor structure is assessed using guided-mode propagation analysis and the performance of the proposed sensor has been benchmarked against the conventional sensor using a Gaussian beam. Furthermore, the study has been corroborated using a finite-difference beam propagation method in Lumerical's Mode Solutions software to investigate the propagation of the zero-order BG beam inside the sensor structure. Based on the simulation outcomes, the proposed scheme yields a maximum absolute sensitivity of up to 3.551 dB / mm and a sensing resolution of 2.816 × 10 - 3 mm through the choice of an appropriate length of NCF at an operating wavelength of 1.55 μm. Owing to this superior sensing performance, the reported sensing technology expedites an avenue to devise a high-performance fiber optic-level sensor that finds profound implication in different physical, biological, and chemical sensing purposes.

Temporally and spatially uniform rates of erosion in the southern Appalachian Great Smoky Mountains

USGS Publications Warehouse

Matmon, A.; Bierman, P.R.; Larsen, J.; Southworth, S.; Pavich, M.; Caffee, M.

2003-01-01

We measured 10Be in fluvial sediment samples (n = 27) from eight Great Smoky Mountain drainages (1-330 km2). Results suggest spatially homogeneous sediment generation (on the 104-105 yr time scale and > 100 km2 spatial scale) at 73 ?? 11 t km-2 yr-1, equivalent to 27 ?? 4 m/m.y. of bedrock erosion. This rate is consistent with rates derived from fission-track, long-term sediment budget, and sediment yield data, all of which indicate that the Great Smoky Mountains and the southern Appalachians eroded during the Mesozoic and Cenozoic at ???30 m/m.y. In contrast, unroofing rates during the Paleozoic orogenic events that formed the Appalachian Mountains were higher (???102 m/m.y.). Erosion rates decreased after termination of tectonically driven uplift, enabling the survival of this ancient mountain belt with its deep crustal root as an isostatically maintained feature in the contemporary landscape.

A case of methimazole-induced hypothyroidism in a patient with endemic goiter: effects of endogenous TSH hyperstimulation after discontinuation of the drug.

PubMed

Messina, M; Manieri, C; Spagnuolo, F; Sardi, E; Allegramente, L; Monaco, A; Ciccarelli, E

1989-04-01

Serum thyroid hormone and TSH concentrations were monitored in a patient with multinodular endemic goiter and severe methimazole (MMI) induced hypothyrodism up to 190 days after drug withdrawal. Serum concentrations of TT3, TT4 and TSH returned to normal values at the 6th., the 140th, and the 120th. day respectively. Within the first 20 days after MMI withdrawal the increase of serum T3 levels was correlated with the observed decrease of serum TSH concentrations. Successively T3 values decreased and T4 levels progressively increased. Six months after MMI withdrawal basal serum TSH concentration was normal while an exaggerated response to TRH was observed. We think that this peculiar hormone pattern is due to iodine depletion. In this case TSH hyperstimulation increases predominantly T3 secretion demonstrating the reduced thyroidal ability to produce T4 when hyperstimulated.

The 26 January 2001 M 7.6 Bhuj, India, earthquake: Observed and predicted ground motions

USGS Publications Warehouse

Hough, S.E.; Martin, S.; Bilham, R.; Atkinson, G.M.

2002-01-01

Although local and regional instrumental recordings of the devastating 26, January 2001, Bhuj earthquake are sparse, the distribution of macroseismic effects can provide important constraints on the mainshock ground motions. We compiled available news accounts describing damage and other effects and interpreted them to obtain modified Mercalli intensities (MMIs) at >200 locations throughout the Indian subcontinent. These values are then used to map the intensity distribution throughout the subcontinent using a simple mathematical interpolation method. Although preliminary, the maps reveal several interesting features. Within the Kachchh region, the most heavily damaged villages are concentrated toward the western edge of the inferred fault, consistent with western directivity. Significant sediment-induced amplification is also suggested at a number of locations around the Gulf of Kachchh to the south of the epicenter. Away from the Kachchh region, intensities were clearly amplified significantly in areas that are along rivers, within deltas, or on coastal alluvium, such as mudflats and salt pans. In addition, we use fault-rupture parameters inferred from teleseismic data to predict shaking intensity at distances of 0-1000 km. We then convert the predicted hard-rock ground-motion parameters to MMI by using a relationship (derived from Internet-based intensity surveys) that assigns MMI based on the average effects in a region. The predicted MMIs are typically lower by 1-3 units than those estimated from news accounts, although they do predict near-field ground motions of approximately 80%g and potentially damaging ground motions on hard-rock sites to distances of approximately 300 km. For the most part, this discrepancy is consistent with the expected effect of sediment response, but it could also reflect other factors, such as unusually high building vulnerability in the Bhuj region and a tendency for media accounts to focus on the most dramatic damage, rather than the average effects. The discrepancy may also be partly attributable to the inadequacy of the empirical relationship between MMI and peak ground acceleration (PGA), when applied to India. The MMI-PGA relationship was developed using data from California earthquakes, which might have a systematically different stress drop and therefore, a different frequency content than intraplate events. When a relationship between response spectra and MMI is used, we obtain larger predicted MMI values, in better agreement with the observations.

Alcohol sensor based on u-bent hetero-structured fiber optic

NASA Astrophysics Data System (ADS)

Patrialova, Sefi N.; Hatta, Agus M.; Sekartedjo, Sekartedjo

2016-11-01

A sensor based on a fiber optic hetero-structure to determine the concentration of alcohol has been proposed. The structure of the sensing probe in this research is a singlemode-multimode-singlemode (SMS) which bent into Ushaped and soon called as SMS u-bent. The SMS structure was chosen to get a higher sensitivity. This research utilizes the principle of multimode interference and evanescent field by modifying the cladding with various alcohol concentration. Testing of the sensor's performance has been done by measuring the sensor's power output response to the length of the SMS fiber optic, bending diameter, and alcohol concentration. Based on the experiment result, the ubent SMS fiber optic with 50 mm bending diameter and 63 mm MMF lenght has the highest sensitivity, 3.87 dB/% and the minimum resolution, 0.26 x 10-3 %.

Superfocusing of mutimode semiconductor lasers and light-emitting diodes

NASA Astrophysics Data System (ADS)

Sokolovskii, G. S.; Dudelev, V. V.; Losev, S. N.; Deryagin, A. G.; Kuchinskii, V. I.; Sibbett, W.; Rafailov, E. U.

2012-05-01

The problem of focusing multimode radiation of high-power semiconductor lasers and light-emitting diodes (LEDs) has been studied. In these sources, low spatial quality of the output beam determines theoretical limit of the focal spot size (one to two orders of magnitude exceeding the diffraction limit), thus restricting the possibility of increasing power density and creating optical field gradients that are necessary in many practical applications. In order to overcome this limitation, we have developed a method of superfocusing of multimode radiation with the aid of interference. It is shown that, using this method, the focal spot size of high-power semiconductor lasers and LEDs can be reduced to a level unachievable by means of traditional focusing. An approach to exceed the theoretical limit of power density for focusing of radiation with high propagation parameter M 2 is proposed.

Active Multimodal Sensor System for Target Recognition and Tracking

PubMed Central

Zhang, Guirong; Zou, Zhaofan; Liu, Ziyue; Mao, Jiansen

2017-01-01

High accuracy target recognition and tracking systems using a single sensor or a passive multisensor set are susceptible to external interferences and exhibit environmental dependencies. These difficulties stem mainly from limitations to the available imaging frequency bands, and a general lack of coherent diversity of the available target-related data. This paper proposes an active multimodal sensor system for target recognition and tracking, consisting of a visible, an infrared, and a hyperspectral sensor. The system makes full use of its multisensor information collection abilities; furthermore, it can actively control different sensors to collect additional data, according to the needs of the real-time target recognition and tracking processes. This level of integration between hardware collection control and data processing is experimentally shown to effectively improve the accuracy and robustness of the target recognition and tracking system. PMID:28657609

Modified Mercalli intensity assignments for the May 16, 1909, Northern Plains earthquake

USGS Publications Warehouse

Bakun, W.H.; Stickney, M.C.; Rogers, G.; Ristau, J.

2010-01-01

We use newspaper accounts from the United States and Canada to assign modified Mercalli intensity (MMI) at 90 towns for the May 16, 1909 Northern Plains earthquake. Our MMI assignments generally are consistent with those plotted on Nuttli's (1976) isoseiemal map. The earthquake was felt over more than 1,500,000 km2 in the states of Minnesota, Montana, North Dakota, South Dakota, and Wyoming and the provinces of Alberta, Manitoba, Ontario, and Saskatchewan.

gene GIS: Computational Tools for Spatial Analyses of DNA Profiles with Associated Photo-Identification and Telemetry Records of Marine Mammals

DTIC Science & Technology

2011-09-30

DNA profiles. Referred to as geneGIS, the program will provide the ability to display, browse, select, filter and summarize spatial or temporal...of the SPLASH photo-identification records and available DNA profiles is underway through integration and crosschecking by Cascadia and MMI . An...Darwin Core standards where possible and can accommodate the current databases developed for telemetry data at MMI and SPLASH collection records at

geneGIS: Computational Tools for Spatial Analyses of DNA Profiles with Associated Photo-Identification and Telemetry Records of Marine Mammals

DTIC Science & Technology

2012-09-30

computational tools provide the ability to display, browse, select, filter and summarize spatio-temporal relationships of these individual-based...her research assistant at Esri, Shaun Walbridge, and members of the Marine Mammal Institute ( MMI ), including Tomas Follet and Debbie Steel. This...Genomics Laboratory, MMI , OSU. 4 As part of the geneGIS initiative, these SPLASH photo-identification records and the geneSPLASH DNA profiles

Comparability among four invertebrate sampling methods and two multimetric indexes, Fountain Creek Basin, Colorado, 2010–2012

USGS Publications Warehouse

Bruce, James F.; Roberts, James J.; Zuellig, Robert E.

2018-05-24

The U.S. Geological Survey (USGS), in cooperation with Colorado Springs City Engineering and Colorado Springs Utilities, analyzed previously collected invertebrate data to determine the comparability among four sampling methods and two versions (2010 and 2017) of the Colorado Benthic Macroinvertebrate Multimetric Index (MMI). For this study, annual macroinvertebrate samples were collected concurrently (in space and time) at 15 USGS surface-water gaging stations in the Fountain Creek Basin from 2010 to 2012 using four sampling methods. The USGS monitoring project in the basin uses two of the methods and the Colorado Department of Public Health and Environment recommends the other two. These methods belong to two distinct sample types, one that targets single habitats and one that targets multiple habitats. The study results indicate that there are significant differences in MMI values obtained from the single-habitat and multihabitat sample types but methods from each program within each sample type produced comparable values. This study also determined that MMI values calculated by different versions of the Colorado Benthic Macroinvertebrate MMI are indistinguishable. This indicates that the Colorado Department of Public Health and Environment methods are comparable with the USGS monitoring project methods for single-habitat and multihabitat sample types. This report discusses the direct application of the study results to inform the revision of the existing USGS monitoring project in the Fountain Creek Basin.

Unusual Synchronous Methimazole-Induced Agranulocytosis and Severe Hepatotoxicity in Patient with Hyperthyroidism: A Case Report and Review of the Literature

PubMed Central

Yang, Jun; Zhang, Jun; Xu, Qin; Sheng, Guo-ping; Weng, Wan-wen; Dong, Meng-jie

2015-01-01

Context. To report a patient with hyperthyroidism who developed concurrent occurrence of agranulocytosis and severe hepatotoxicity after taking methimazole (MMI). Case. A 51-year-old Chinese male was diagnosed as hyperthyroidism with normal white blood count and liver function. After 4 weeks' treatment with MMI 20 mg/d, it developed to agranulocytosis and severe cholestatic hepatotoxicity. The patient's symptoms and laboratory abnormalities disappeared after the withdrawal of MMI; his white blood count and liver function recover to normal in 2 weeks and 5 weeks, respectively. 296 MBq dose of 131I was given to the patient 3 weeks after the withdrawal of MMI and his thyroid function was back to normal in 6 months. As we know through literature review, only 5 previous cases reported the synchronous ATD-induced agranulocytosis and severe hepatotoxicity in patients with hyperthyroidism. Methods. Review of the patient's clinical course. Literature review of cases of hyperthyroidism with agranulocytosis and severe hepatotoxicity demonstrated that these complications occurred after taking antithyroid drug (ATD). Conclusions. Patient with hyperthyroidism can have synchronous ATD-induced agranulocytosis and severe hepatotoxicity. This case is extremely rare, but the adverse effects with ATDs is clinically significant. The clinicians need to be careful about this and monitor biochemical of patients who take ATDs. PMID:26060496

Development of a thyroperoxidase inhibition assay for high ...

EPA Pesticide Factsheets

High-throughput screening (HTPS) assays to detect inhibitors of thyroperoxidase (TPO), the enzymatic catalyst for thyroid hormone (TH) synthesis, are not currently available. Herein we describe the development of a HTPS TPO inhibition assay. Rat thyroid microsomes and a fluorescent peroxidase substrate, Amplex UltraRed (AUR, LifeTechnologies), were employed in an endpoint assay for comparison to the existing kinetic guaiacol (GUA) oxidation assay. Following optimization of assay metrics including Z’, dynamic range, and activity using methimazole (MMI), the assay was tested with a 21-chemical training set. The potency of MMI-induced TPO inhibition was greater with AUR compared to GUA. The dynamic range and Z’ score with MMI were as follows: 127-fold and 0.62 for the GUA assay, 18-fold and 0.86 for the 96-well AUR assay, and 11.5-fold and 0.93 for the 384-well AUR assay. The 384-well AUR assay drastically reduced animal use, requiring one-tenth of the rat thyroid microsomal protein needed for the GUA 96-well format assay. Fourteen chemicals inhibited TPO, with a relative potency ranking of MMI > ethylene thiourea > 6-propylthiouracil > 2,2’,4,4’-tetrahydroxy-benzophenone > 2-mercaptobenzothiazole > 3-amino-1,2,4-triazole > genistein > 4-propoxyphenol > sulfamethazine > daidzein > 4-nonylphenol > triclosan > iopanoic acid > resorcinol. These data demonstrate the capacity of this assay to detect diverse TPO inhibitors. Seven chemicals acted as negati

Signatures of Indistinguishability in Bosonic Many-Body Dynamics

NASA Astrophysics Data System (ADS)

Brünner, Tobias; Dufour, Gabriel; Rodríguez, Alberto; Buchleitner, Andreas

2018-05-01

The dynamics of bosons in generic multimode systems, such as Bose-Hubbard models, are not only determined by interactions among the particles, but also by their mutual indistinguishability manifested in many-particle interference. We introduce a measure of indistinguishability for Fock states of bosons whose mutual distinguishability is controlled by an internal degree of freedom. We demonstrate how this measure emerges both in the noninteracting and interacting evolution of observables. In particular, we find an unambiguous relationship between our measure and the variance of single-particle observables in the noninteracting limit. A nonvanishing interaction leads to a hierarchy of interaction-induced interference processes, such that even the expectation value of single-particle observables is influenced by the degree of indistinguishability.

Analysis of 90 cases of antithyroid drug-induced severe hepatotoxicity over 13 years in China.

PubMed

Yang, Jun; Li, Lin-Fa; Xu, Qin; Zhang, Jun; Weng, Wan-Wen; Zhu, Yang-Jun; Dong, Meng-Jie

2015-03-01

Antithyroid drug (ATD)-induced severe hepatotoxicity is a rare but serious complication of ATD therapy. The characteristics of severe hepatotoxicity have been reported in only a small number of patients. Ninety patients with ATD-induced severe hepatotoxicity presenting during a 13 year period (2000-2013) who were about to undergo nuclear medicine therapy with (131)I from a sample of 8864 patients with hyperthyroidism were studied, and the outcomes were evaluated. The mean age of the patients with ATD-induced severe hepatotoxicity was 41.6±12.5 years (mean±standard deviation), and the female to male ratio was 2.2:1. The methimazole (MMI) dose given at the onset was 19.1±7.4 mg/day. The propylthiouracil (PTU) dose given at the onset was 212.8±105.0 mg/day. ATD-induced severe hepatotoxicity occurred in 63.3%, 75.6%, and 81.1% of patients within 4, 8, and 12 weeks of the onset of ATD therapy, respectively. The types of severe hepatotoxicity did not differ significantly between the MMI and PTU groups (p=0.188). The frequency of the cholestatic type in the MMI group (35.3%, 18/51) was higher than that in the PTU group (17.9%, 7/39), but these frequencies were not significantly different (p=0.069). The patients who were treated with (131)I received an average dose of 279.1±86.1 MBq (n=84). Therapy was successful in 60 of the 67 patients (89.6%). The success rate was equivalent (p=0.696) between the groups receiving MMI (91.7%, 33/36) and PTU (87.1%, 27/31). Severe hepatotoxicity tends to occur within the first three months after the onset of ATD therapy. The type of ATD-induced severe hepatotoxicity did not differ between the MMI and PTU groups. (131)I therapy is an effective treatment approach for patients with ATD-induced severe hepatotoxicity.

Classification VIA Information-Theoretic Fusion of Vector-Magnetic and Acoustic Sensor Data

DTIC Science & Technology

2007-04-01

10) where tBsBtBsBtBsBtsB zzyyxx, . (11) The operation in (10) may be viewed as a vector matched- filter on to estimate )(tB CPARv . In summary...choosing to maximize the classification information in Y are described in Section 3.2. A 3.2. Maximum mutual information ( MMI ) features We begin with a...review of several desirable properties of features that maximize a mutual information ( MMI ) criterion. Then we review a particular algorithm [2

Multimodal technique to eliminate humidity interference for specific detection of ethanol.

PubMed

Jalal, Ahmed Hasnain; Umasankar, Yogeswaran; Gonzalez, Pablo J; Alfonso, Alejandro; Bhansali, Shekhar

2017-01-15

Multimodal electrochemical technique incorporating both open circuit potential (OCP) and amperometric techniques have been conceptualized and implemented to improve the detection of specific analyte in systems where more than one analyte is present. This approach has been demonstrated through the detection of ethanol while eliminating the contribution of water in a micro fuel cell sensor system. The sensor was interfaced with LMP91000 potentiostat, controlled through MSP430F5529LP microcontroller to implement an auto-calibration algorithm tailored to improve the detection of alcohol. The sensor was designed and fabricated as a three electrode system with Nafion as a proton exchange membrane (PEM). The electrochemical signal of the interfering phase (water) was eliminated by implementing the multimodal electrochemical detection technique. The results were validated by comparing sensor and potentiostat performances with a commercial sensor and potentiostat respectively. The results suggest that such a sensing system can detect ethanol at concentrations as low as 5ppm. The structure and properties such as low detection limit, selectivity and miniaturized size enables potential application of this device in wearable transdermal alcohol measurements. Copyright © 2016 Elsevier B.V. All rights reserved.

Suppression law of quantum states in a 3D photonic fast Fourier transform chip

PubMed Central

Crespi, Andrea; Osellame, Roberto; Ramponi, Roberta; Bentivegna, Marco; Flamini, Fulvio; Spagnolo, Nicolò; Viggianiello, Niko; Innocenti, Luca; Mataloni, Paolo; Sciarrino, Fabio

2016-01-01

The identification of phenomena able to pinpoint quantum interference is attracting large interest. Indeed, a generalization of the Hong–Ou–Mandel effect valid for any number of photons and optical modes would represent an important leap ahead both from a fundamental perspective and for practical applications, such as certification of photonic quantum devices, whose computational speedup is expected to depend critically on multi-particle interference. Quantum distinctive features have been predicted for many particles injected into multimode interferometers implementing the Fourier transform over the optical modes. Here we develop a scalable approach for the implementation of the fast Fourier transform algorithm using three-dimensional photonic integrated interferometers, fabricated via femtosecond laser writing technique. We observe the suppression law for a large number of output states with four- and eight-mode optical circuits: the experimental results demonstrate genuine quantum interference between the injected photons, thus offering a powerful tool for diagnostic of photonic platforms. PMID:26843135

Effect of time variation on coating characteristic of Ti-6Al-4V alloy coated with TiO2 by dip coating method

NASA Astrophysics Data System (ADS)

Hashim Aneed, Shaymaa

2018-05-01

In this reserch samples of Ti-6Al-4V alloy was coated with TiO2 layer by dip coating method in solution consist of 8 gm TiO2 nanoparticle dissolved in 100 ml. ethanol absolute (99%) and 1 gm P2O5, with various coating periods (1,2,3) minuts. The corrosion characteristics was investigated using (parstat 2273,USA made),the corrosion rate reach to 7.047 × 10-4 mm/y for sample coated at 3 minutes compared with 8.266 × 10-3mm/y for uncoated sample. Then the samples immersed in simulated body fluid (SBF) synthesized in the laboratory for one month in order to investigate the osseointegration from hydroxyapatite biomimatically formed, the corrosion charactaristics also invistigated after immirsing in (SBF) and it was 1.479 × 10-4 mm/y. For each part of reaserch we test the optical microscopic images,XRD and SEM in order to evaluate the results.

Multi-monochromatic imaging of defect-induced mix experiments at OMEGA

NASA Astrophysics Data System (ADS)

Mancini, Roberto; Johns, Heather; Joshi, Tirtha; Mayes, Daniel; Durmaz, Tunay; Nagayama, Taisuke; Hsu, Scott; Tregillis, Ian; Krasheninnikova, Natalia; Cobble, James; Murphy, Thomas; Shah, Rahul; Kyrala, George; Hakel, Peter; Bradley, Paul; Schmitt, Mark

2012-10-01

In a series of polar-drive implosions performed at OMEGA for the defect-induced mix experiment (DIME) campaign of Los Alamos National Laboratory, two identical multi-monochromatic imager (MMI) instruments were fielded to record gated, x-ray spectrally-resolved images of D-filled Ti-doped plastic shells. The shells included a defect on the equatorial plane to study defect-induced mix while no-defect shells were employed in reference shots. The MMI data recorded simultaneously along quasi-orthogonal lines-of-sight afforded unique observations of the implosion based on the K-shell spectral signatures of the Ti tracer. Several analysis techniques have been used to process the MMI data (T. Nagayama et al, J. App. Phys. 109, 093303 (2011)) in order to study defect-induced mixing by tracking the spatial distribution and state of the tracer. Comparisons were made with results from post-processed 2D and 3D simulations to provide further insight into the interpretation of the experimental results and to constrain the simulation physics model.

Corrosion control when using passively treated abandoned mine drainage as alternative makeup water for cooling systems.

PubMed

Hsieh, Ming-Kai; Chien, Shih-Hsiang; Li, Heng; Monnell, Jason D; Dzombak, David A; Vidic, Radisav D

2011-09-01

Passively treated abandoned mine drainage (AMD) is a promising alternative to fresh water as power plant cooling water system makeup water in mining regions where such water is abundant. Passive treatment and reuse of AMD can avoid the contamination of surface water caused by discharge of abandoned mine water, which typically is acidic and contains high concentrations of metals, especially iron. The purpose of this study was to evaluate the feasibility of reusing passively treated AMD in cooling systems with respect to corrosion control through laboratory experiments and pilot-scale field testing. The results showed that, with the addition of the inhibitor mixture orthophosphate and tolyltriazole, mild steel and copper corrosion rates were reduced to acceptable levels (< 0.127 mm/y and < 0.0076 mm/y, respectively). Aluminum had pitting corrosion problems in every condition tested, while cupronickel showed that, even in the absence of any inhibitor and in the presence of the biocide monochloramine, its corrosion rate was still very low (0.018 mm/y).

Congenital anomalies in children exposed to antithyroid drugs in-utero: a meta-analysis of cohort studies.

PubMed

Li, Huixia; Zheng, Jianfei; Luo, Jiayou; Zeng, Rong; Feng, Na; Zhu, Na; Feng, Qi

2015-01-01

Hyperthyroidism affects about 0.2%-2.7% of all pregnancies, and is commonly managed with antithyroid drugs (ATDs). However, previous studies about the effects of ATDs on congenital anomalies are controversial. Therefore, the present meta-analysis was performed to explore the risk of congenital anomalies in children exposed to ATDs in-utero. Embase, Pubmed, Web of Knowledge, and BIOSIS Citation Index were searched to find out studies about congenital anomalies in children exposed to ATDs in-utero reported up to May 2014. The references cited by the retrieved articles were also searched. The relative risks (RRs) and confidence intervals (CIs) for the individual studies were pooled by fixed effects models, and heterogeneity was analyzed by chi-square and I2 tests. Eight studies met the inclusion criteria. Exposure to propylthiouracil (PTU), methimazole/carbimazole (MMI/CMZ), and PTU & MMI/CMZ was investigated in 7, 7 and 2 studies, respectively. The pooled RR was 1.20 (95%CI: 1.02-1.42), 1.64 (95%CI: 1.39-1.92), and 1.83 (95%CI: 1.30-2.56) for congenital anomalies after exposure to PTU, MMI/CMZ, and PTU & MMI/CMZ, respectively. The meta-analysis suggests that exposure to ATDs in-utero increases the risk of congenital anomalies. The use of ATDs in pregnancy should be limited when possible. Further research is needed to delineate the exact teratogenic risk for particular congenital anomaly.

Congenital Anomalies in Children Exposed to Antithyroid Drugs In-Utero: A Meta-Analysis of Cohort Studies

PubMed Central

Luo, Jiayou; Zeng, Rong; Feng, Na; Zhu, Na; Feng, Qi

2015-01-01

Background Hyperthyroidism affects about 0.2%-2.7% of all pregnancies, and is commonly managed with antithyroid drugs (ATDs). However, previous studies about the effects of ATDs on congenital anomalies are controversial. Therefore, the present meta-analysis was performed to explore the risk of congenital anomalies in children exposed to ATDs in-utero. Methods Embase, Pubmed, Web of Knowledge, and BIOSIS Citation Index were searched to find out studies about congenital anomalies in children exposed to ATDs in-utero reported up to May 2014. The references cited by the retrieved articles were also searched. The relative risks (RRs) and confidence intervals (CIs) for the individual studies were pooled by fixed effects models, and heterogeneity was analyzed by chi-square and I 2 tests. Results Eight studies met the inclusion criteria. Exposure to propylthiouracil (PTU), methimazole/carbimazole (MMI/CMZ), and PTU & MMI/CMZ was investigated in 7, 7 and 2 studies, respectively. The pooled RR was 1.20 (95%CI: 1.02-1.42), 1.64 (95%CI: 1.39-1.92), and 1.83 (95%CI: 1.30-2.56) for congenital anomalies after exposure to PTU, MMI/CMZ, and PTU & MMI/CMZ, respectively. Conclusions The meta-analysis suggests that exposure to ATDs in-utero increases the risk of congenital anomalies. The use of ATDs in pregnancy should be limited when possible. Further research is needed to delineate the exact teratogenic risk for particular congenital anomaly. PMID:25974033

Using Modified Mercalli Intensities to estimate acceleration response spectra for the 1906 San Francisco earthquake

USGS Publications Warehouse

Boatwright, J.; Bundock, H.; Seekins, L.C.

2006-01-01

We derive and test relations between the Modified Mercalli Intensity (MMI) and the pseudo-acceleration response spectra at 1.0 and 0.3 s - SA(1.0 s) and SA(0.3 s) - in order to map response spectral ordinates for the 1906 San Francisco earthquake. Recent analyses of intensity have shown that MMI ??? 6 correlates both with peak ground velocity and with response spectra for periods from 0.5 to 3.0 s. We use these recent results to derive a linear relation between MMI and log SA(1.0 s), and we refine this relation by comparing the SA(1.0 s) estimated from Boatwright and Bundock's (2005) MMI map for the 1906 earthquake to the SA(1.0 s) calculated from recordings of the 1989 Loma Prieta earthquake. South of San Jose, the intensity distributions for the 1906 and 1989 earthquakes are remarkably similar, despite the difference in magnitude and rupture extent between the two events. We use recent strong motion regressions to derive a relation between SA(1.0 s) and SA(0.3 s) for a M7.8 strike-slip earthquake that depends on soil type, acceleration level, and source distance. We test this relation by comparing SA(0.3 s) estimated for the 1906 earthquake to SA(0.3 s) calculated from recordings of both the 1989 Loma Prieta and 1994 Northridge earthquakes, as functions of distance from the fault. ?? 2006, Earthquake Engineering Research Institute.

Which Assessment Method of Malnutrition in Head and Neck Cancer?

PubMed

Saroul, Nicolas; Pastourel, Rémy; Mulliez, Aurélien; Farigon, Nicolas; Dupuch, Vincent; Mom, Thierry; Boirie, Yves; Gilain, Laurent

2018-06-01

Objective To assess the value of several diagnostic methods of nutritional status during the initial management of a head and neck cancer. Study Design Single-center prospective study. Setting Tertiary referral center. Subjects and Methods Ninety patients with head and neck cancer participated in the study. Assessment of their nutritional status was made with anthropometric, biological, body, and muscle measurements (the last by computed tomography: L3 muscle mass index [L3MMI]). Assessment of muscle performance (functional reflection of nutritional status) was made via the Short Physical Performance Battery test. The malnutrition thresholds were set according to the literature. Results Mean body mass index (BMI) was 24.6 ± 5.4 kg/m 2 . Mean weight loss and albumin levels were -4.5 ± 10.5 kg and 37.1 ± 5.2 g/L, respectively. Fourteen percent of patients were diagnosed as malnourished on the basis of BMI, 54% according to the Nutritional Risk Index (NRI), and 58% by L3MMI. There was 64% agreement between NRI and L3MMI ( P < .001). All patients identified as malnourished by BMI were considered as such by the other assessment methods; however, many malnourished patients had normal or high BMI. The Short Physical Performance Battery score was low particularly among patients considered to be the most undernourished by the other methods. Conclusion NRI and L3MMI are the best methods to identify patients as being malnourished. Functional muscle assessment can determine the severity of malnutrition.

Fiber Optic-Based Refractive Index Sensing at INESC Porto

PubMed Central

Jorge, Pedro A. S.; Silva, Susana O.; Gouveia, Carlos; Tafulo, Paula; Coelho, Luis; Caldas, Paulo; Viegas, Diana; Rego, Gaspar; Baptista, José M.; Santos, José L.; Frazão, Orlando

2012-01-01

A review of refractive index measurement based on different types of optical fiber sensor configurations and techniques is presented. It addresses the main developments in the area, with particular focus on results obtained at INESC Porto, Portugal. The optical fiber sensing structures studied include those based on Bragg and long period gratings, on micro-interferometers, on plasmonic effects in fibers and on multimode interference in a large spectrum of standard and microstructured optical fibers. PMID:22969405

Narrow-linewidth broadly tunable Yb-doped Q-switched fiber laser using multimode interference filter.

PubMed

Chakravarty, Usha; Mukhopadhyay, P K; Kuruvilla, A; Upadhyaya, B N; Bindra, K S

2017-05-01

A narrow-linewidth broadly tunable Yb-doped Q-switched fiber laser using an acousto-optic modulator and multimode interference filter (MMIF) in the linear bulk cavity resonator and an all-fiber ring cavity resonator has been demonstrated. Insertion of an MMIF in the linear cavity resonator using bulk components decreased the spectral bandwidth of the Q-switched signal by two orders of magnitude from 11 to less than 0.1 nm. Spectral tunability of more than 16 nm in the range from 1057 to 1073 nm has also been achieved by the combination of MMIF and a standard polarization controller (SPC). A decrease in the pulse duration with a decrease in the spectral bandwidth of the output signal has also been recorded. The pulse duration of the Q-switched signal was reduced from ∼305 to ∼240  ns by the introduction of the MMIF in the resonator at the same value of the input pump power. In the case of the all-fiber Q-switched ring cavity resonator, the spectral bandwidth of the Q-switched signal was reduced by two orders of magnitude from ∼17 to less than 0.1 nm due to the introduction of the MMIF in the resonator. The spectral tunability of more than 12 nm in the range from 1038 to 1050 nm was achieved by an MMIF and an SPC.

Nonlinear multimodal model for TLD of irregular tank geometry and small fluid depth

NASA Astrophysics Data System (ADS)

Love, J. S.; Tait, M. J.

2013-11-01

Tuned liquid dampers (TLDs) utilize sloshing fluid to absorb and dissipate structural vibrational energy. TLDs of irregular or complex tank geometry may be required in practice to avoid tank interference with fixed structural or mechanical components. The literature offers few analytical models to predict the response of this type of TLD, particularly when the fluid depth is small. In this paper, a multimodal model is developed utilizing a Boussinesq-type modal theory which is valid for small TLD fluid depths. The Bateman-Luke variational principle is employed to develop a system of coupled nonlinear ordinary differential equations which describe the fluid response when the tank is subjected to base excitation. Energy dissipation is incorporated into the model from the inclusion of damping screens. The fluid model is used to describe the response of a 2D structure-TLD system when the structure is subjected to external loading and the TLD tank geometry is irregular.

Coherence properties of spontaneous parametric down-conversion pumped by a multi-mode cw diode laser.

PubMed

Kwon, Osung; Ra, Young-Sik; Kim, Yoon-Ho

2009-07-20

Coherence properties of the photon pair generated via spontaneous parametric down-conversion pumped by a multi-mode cw diode laser are studied with a Mach-Zehnder interferometer. Each photon of the pair enters a different input port of the interferometer and the biphoton coherence properties are studied with a two-photon detector placed at one output port. When the photon pair simultaneously enters the interferometer, periodic recurrence of the biphoton de Broglie wave packet is observed, closely resembling the coherence properties of the pump diode laser. With non-zero delays between the photons at the input ports, biphoton interference exhibits the same periodic recurrence but the wave packet shapes are shown to be dependent on both the input delay as well as the interferometer delay. These properties could be useful for building engineered entangled photon sources based on diode laser-pumped spontaneous parametric down-conversion.

Multimodal optical workstation for simultaneous linear, nonlinear microscopy and nanomanipulation: upgrading a commercial confocal inverted microscope.

PubMed

Mathew, Manoj; Santos, Susana I C O; Zalvidea, Dobryna; Loza-Alvarez, Pablo

2009-07-01

In this work we propose and build a multimodal optical workstation that extends a commercially available confocal microscope (Nikon Confocal C1-Si) to include nonlinear/multiphoton microscopy and optical manipulation/stimulation tools such as nanosurgery. The setup allows both subsystems (confocal and nonlinear) to work independently and simultaneously. The workstation enables, for instance, nanosurgery along with simultaneous confocal and brightfield imaging. The nonlinear microscopy capabilities are added around the commercial confocal microscope by exploiting all the flexibility offered by this microscope and without need for any mechanical or electronic modification of the confocal microscope systems. As an example, the standard differential interference contrast condenser and diascopic detector in the confocal microscope are readily used as a forward detection mount for second harmonic generation imaging. The various capabilities of this workstation, as applied directly to biology, are demonstrated using the model organism Caenorhabditis elegans.

Optical circulation in a multimode optomechanical resonator.

PubMed

Ruesink, Freek; Mathew, John P; Miri, Mohammad-Ali; Alù, Andrea; Verhagen, Ewold

2018-05-04

Breaking the symmetry of electromagnetic wave propagation enables important technological functionality. In particular, circulators are nonreciprocal components that can route photons directionally in classical or quantum photonic circuits and offer prospects for fundamental research on electromagnetic transport. Developing highly efficient circulators thus presents an important challenge, especially to realise compact reconfigurable implementations that do not rely on magnetic fields to break reciprocity. We demonstrate optical circulation utilising radiation pressure interactions in an on-chip multimode optomechanical system. Mechanically mediated optical mode conversion in a silica microtoroid provides a synthetic gauge bias for light, enabling four-port circulation that exploits tailored interference between appropriate light paths. We identify two sideband conditions under which ideal circulation is approached. This allows to experimentally demonstrate ~10 dB isolation and <3 dB insertion loss in all relevant channels. We show the possibility of actively controlling the circulator properties, enabling ideal opportunities for reconfigurable integrated nanophotonic circuits.

Tunable Q-switched erbium doped fiber laser based on metal transition oxide saturable absorber and refractive index characteristic of multimode interference effects

NASA Astrophysics Data System (ADS)

Mohammed, D. Z.; Khaleel, Wurood Abdulkhaleq; Al-Janabi, A. H.

2017-12-01

Ferro-oxide (Fe3O4) nanoparticles were used as a saturable absorber (SA) for a passively Q-switched erbium doped fiber laser (EDFL) with ring cavity. The Q-switching operation was achieved at a pump threshold of 80 mW. The proposed fiber laser produces stable pulses train of repetition rate ranging from 25 kHz to 80 kHz as the pump power increases from threshold to 342 mW. The minimum recorded pulse width was 2.7 μs at 342 mW. The C-band tunability operation was performed using single mode-multimode-single mode fiber (SM-MM-SM) structure. The laser exhibited a total tuning range of 7 nm, maximum sensitivity of 106.9 nm, optical signal to noise ratio (OSNR) of 38 dB and 3-dB linewidth of 0.06 nm.

Fifty years of progress in speech and speaker recognition

NASA Astrophysics Data System (ADS)

Furui, Sadaoki

2004-10-01

Speech and speaker recognition technology has made very significant progress in the past 50 years. The progress can be summarized by the following changes: (1) from template matching to corpus-base statistical modeling, e.g., HMM and n-grams, (2) from filter bank/spectral resonance to Cepstral features (Cepstrum + DCepstrum + DDCepstrum), (3) from heuristic time-normalization to DTW/DP matching, (4) from gdistanceh-based to likelihood-based methods, (5) from maximum likelihood to discriminative approach, e.g., MCE/GPD and MMI, (6) from isolated word to continuous speech recognition, (7) from small vocabulary to large vocabulary recognition, (8) from context-independent units to context-dependent units for recognition, (9) from clean speech to noisy/telephone speech recognition, (10) from single speaker to speaker-independent/adaptive recognition, (11) from monologue to dialogue/conversation recognition, (12) from read speech to spontaneous speech recognition, (13) from recognition to understanding, (14) from single-modality (audio signal only) to multi-modal (audio/visual) speech recognition, (15) from hardware recognizer to software recognizer, and (16) from no commercial application to many practical commercial applications. Most of these advances have taken place in both the fields of speech recognition and speaker recognition. The majority of technological changes have been directed toward the purpose of increasing robustness of recognition, including many other additional important techniques not noted above.

A direct temporal domain approach for ultrafast optical signal processing and its implementation using planar lightwave circuits

NASA Astrophysics Data System (ADS)

Xia, Bing

Ultrafast optical signal processing, which shares the same fundamental principles of electrical signal processing, can realize numerous important functionalities required in both academic research and industry. Due to the extremely fast processing speed, all-optical signal processing and pulse shaping have been widely used in ultrafast telecommunication networks, photonically-assisted RFlmicro-meter waveform generation, microscopy, biophotonics, and studies on transient and nonlinear properties of atoms and molecules. In this thesis, we investigate two types of optical spectrally-periodic (SP) filters that can be fabricated on planar lightwave circuits (PLC) to perform pulse repetition rate multiplication (PRRM) and arbitrary optical waveform generation (AOWG). First, we present a direct temporal domain approach for PRRM using SP filters. We show that the repetition rate of an input pulse train can be multiplied by a factor N using an optical filter with a free spectral range that does not need to be constrained to an integer multiple of N. Furthermore, the amplitude of each individual output pulse can be manipulated separately to form an arbitrary envelope at the output by optimizing the impulse response of the filter. Next, we use lattice-form Mach-Zehnder interferometers (LF-MZI) to implement the temporal domain approach for PRRM. The simulation results show that PRRM with uniform profiles, binary-code profiles and triangular profiles can be achieved. Three silica based LF-MZIs are designed and fabricated, which incorporate multi-mode interference (MMI) couplers and phase shifters. The experimental results show that 40 GHz pulse trains with a uniform envelope pattern, a binary code pattern "1011" and a binary code pattern "1101" are generated from a 10 GHz input pulse train. Finally, we investigate 2D ring resonator arrays (RRA) for ultraf ast optical signal processing. We design 2D RRAs to generate a pair of pulse trains with different binary-code patterns simultaneously from a single pulse train at a low repetition rate. We also design 2D RRAs for AOWG using the modified direct temporal domain approach. To demonstrate the approach, we provide numerical examples to illustrate the generation of two very different waveforms (square waveform and triangular waveform) from the same hyperbolic secant input pulse train. This powerful technique based on SP filters can be very useful for ultrafast optical signal processing and pulse shaping.

Quantitative analysis of the tectonic subsidence in the Potiguar Basin (NE Brazil)

NASA Astrophysics Data System (ADS)

Lopes, Juliana A. G.; de Castro, David L.; Bertotti, Giovanni

2018-06-01

The Potiguar Basin, located in the Brazilian Equatorial Margin, evolved from a complex rifting process implemented during the Atlantic Ocean opening in the Jurassic/Cretaceous. Different driving mechanisms were responsible for the onset of an aborted onshore rift and an offshore rift that initiated crustal rupture and the formation of a continental transform margin. Therefore, we applied the backstripping method to quantify the tectonic subsidence during the rift and post-rift phases of Potiguar Basin formation and to analyze the spatial variation of subsidence during the two successive and distinct tectonic events responsible for the basin evolution. The parameters required to apply this methodology were extracted from 2D seismic lines and exploratory well data. The tectonic subsidence curves present periods with moderate subsidence rates (up to 300 m/My), which correspond to the evolution of the onshore Potiguar Rift (∼141 to 128 Ma). From 128-118 Ma, the tectonic subsidence curves show no subsidence in the onshore Potiguar Basin, whereas subsidence occurred at high rates (over 300 m/My) in the offshore rift. The post-rift phase began ca. 118 Ma (Aptian), when the tectonic subsidence drastically slowed to less than 35 m/My, probably related to thermal relaxation. The tectonic subsidence rates in the various sectors of the Potiguar Rift, during the different rift phases, indicate that more intense faulting occurred in the southern portion of the onshore rift, along the main border faults, and in the southeastern portion of the offshore rift. During the post-rift phase, the tectonic subsidence rates increased from the onshore portion towards the offshore portion until the continental slope. The highest rates of post-rift subsidence (up to 35 m/My) are concentrated in the central region of the offshore portion and may be related to lithospheric processes related to the continental crust rupture and oceanic seafloor spreading. The variation in subsidence rates and the pattern of tectonic subsidence curves allowed us to interpret the tectonic signature recorded by the sedimentary sequences of the Potiguar Basin during its evolution. In the onshore rift area, the tectonic subsidence curves presented subsidence rates up to 300 m/My during a long-term rift phase (13 Ma), which confirmed that this portion had an extensional tectonic regime. In the offshore rift, the curves presented high subsidence rates of over 300 m/My in a shorter period (5-10 My), typical of basins formed in a transtensional tectonic regime.

Rayleigh-wave mode separation by high-resolution linear radon transform

USGS Publications Warehouse

Luo, Y.; Xia, J.; Miller, R.D.; Xu, Y.; Liu, J.; Liu, Q.

2009-01-01

Multichannel analysis of surface waves (MASW) method is an effective tool for obtaining vertical shear wave profiles from a single non-invasive measurement. One key step of the MASW method is generation of a dispersion image and extraction of a reliable dispersion curve from raw multichannel shot records. Because different Rayleigh-wave modes normally interfere with each other in the time and space domain, it is necessary to perform mode separation and reconstruction to increase the accuracy of phase velocities determined from a dispersion image. In this paper, we demonstrate the effectiveness of high-resolution linear Radon transform (LRT) as a means of separating and reconstructing multimode, dispersive Rayleigh-wave energy. We first introduce high-resolution LRT methods and Rayleigh-wave mode separation using high-resolution LRT. Next, we use synthetic data and a real-world example to demonstrate the effectiveness of Rayleigh-wave mode separation using high-resolution LRT. Our synthetic and real-world results demonstrate that (1) high-resolution LRT successfully separates and reconstructs multimode dispersive Rayleigh-wave energy with high resolution allowing the multimode energy to be more accurately determined. The horizontal resolution of the Rayleigh-wave method can be increased by extraction of dispersion curves from a pair of traces in the mode-separated shot gather and (2) multimode separation and reconstruction expand the usable frequency range of higher mode dispersive energy, which increases the depth of investigation and provides a means for accurately determining cut-off frequencies. ?? 2009 The Authors Journal compilation ?? 2009 RAS.

A facetless regrowth-free single mode laser based on MMI couplers

NASA Astrophysics Data System (ADS)

Caro, Ludovic; Kelly, Niall P.; Dernaika, Mohamad; Shayesteh, Maryam; Morrissey, Padraic E.; Alexander, Justin K.; Peters, Frank H.

2017-09-01

This paper presents a facetless, tunable laser operating near 1575 nm, as well as a theoretical model predicting spectral features of the laser. The lasers were fabricated without regrowth or advanced lithography techniques, and are based on MMI couplers and etched facets. Coarse vernier tuning was achieved over a range of 25 nm, while fine, thermal tuning was also demonstrated over a range of 1.5 nm. SMSR values of 25 dB and higher were observed, with a measured laser linewidth of 600 kHz.

Optical fibres in pre-detector signal processing

NASA Astrophysics Data System (ADS)

Flinn, A. R.

The basic form of conventional electro-optic sensors is described. The main drawback of these sensors is their inability to deal with the background radiation which usually accompanies the signal. This 'clutter' limits the sensors performance long before other noise such as 'shot' noise. Pre-detector signal processing using the complex amplitude of the light is introduced as a means to discriminate between the signal and 'clutter'. Further improvements to predetector signal processors can be made by the inclusion of optical fibres allowing radiation to be used with greater efficiency and enabling certain signal processing tasks to be carried out with an ease unequalled by any other method. The theory of optical waveguides and their application in sensors, interferometers, and signal processors is reviewed. Geometrical aspects of the formation of linear and circular interference fringes are described along with temporal and spatial coherence theory and their relationship to Michelson's visibility function. The requirements for efficient coupling of a source into singlemode and multimode fibres are given. We describe interference experiments between beams of light emitted from a few metres of two or more, singlemode or multimode, optical fibres. Fresnel's equation is used to obtain expressions for Fresnel and Fraunhofer diffraction patterns which enable electro-optic (E-0) sensors to be analysed by Fourier optics. Image formation is considered when the aperture plane of an E-0 sensor is illuminated with partially coherent light. This allows sensors to be designed using optical transfer functions which are sensitive to the spatial coherence of the illuminating light. Spatial coherence sensors which use gratings as aperture plane reticles are discussed. By using fibre arrays, spatial coherence processing enables E-0 sensors to discriminate between a spatially coherent source and an incoherent background. The sensors enable the position and wavelength of the source to be determined. Experiments are described which use optical fibre arrays as masks for correlation with spatial distributions of light in image planes of E-0 sensors. Correlations between laser light from different points in a scene is investigated by interfering the light emitted from an array of fibres, placed in the image plane of a sensor, with each other. Temporal signal processing experiments show that the visibility of interference fringes gives information about path differences in a scene or through an optical system. Most E-0 sensors employ wavelength filtering of the detected radiation to improve their discrimination and this is shown to be less selective than temporal coherence filtering which is sensitive to spectral bandwidth. Experiments using fibre interferometers to discriminate between red and blue laser light by their bandwidths are described. In most cases the path difference need only be a few tens of centimetres. We consider spatial and temporal coherence in fibres. We show that high visibility interference fringes can be produced by red and blue laser light transmitted through over 100 metres of singlemode or multimode fibre. The effect of detector size, relative to speckle size, is considered for fringes produced by multimode fibres. The effect of dispersion on the coherence of the light emitted from fibres is considered in terms of correlation and interference between modes. We describe experiments using a spatial light modulator called SIGHT-MOD. The device is used in various systems as a fibre optic switch and as a programmable aperture plane reticle. The contrast of the device is measured using red and green, HeNe, sources. Fourier transform images of patterns on the SIGHT-MOD are obtained and used to demonstrate the geometrical manipulation of images using 2D fibre arrays. Correlation of Fourier transform images of the SIGHT-MOD with 2D fibre arrays is demonstrated.

Engaging a community towards marine cyberinfrastructure: Lessons Learned from The Marine Metadata Interoperability initiative

NASA Astrophysics Data System (ADS)

Galbraith, N. R.; Graybeal, J.; Bermudez, L. E.; Wright, D.

2005-12-01

The Marine Metadata Interoperability (MMI) initiative promotes the exchange, integration and use of marine data through enhanced data publishing, discovery, documentation and accessibility. The project, operating since late 2004, presents several cultural organizational challenges because of the diversity of participants: scientists, technical experts, and data managers from around the world, all working in organizations with different corporate cultures, funding structures, and systems of decision-making. MMI provides educational resources at several levels. For instance, short introductions to metadata concepts are available, as well as guides and "cookbooks" for the quick and efficient preparation of marine metadata. For those who are building major marine data systems, including ocean-observing capabilities, there are training materials, marine metadata content examples, and resources for mapping elements between different metadata standards. The MMI also provides examples of good metadata practices in existing data systems, including the EU's Marine XML project, and functioning ocean/coastal clearinghouses and atlases developed by MMI team members. Communication tools that help build community: 1) Website, used to introduce the initiative to new visitors, and to provide in-depth guidance and resources to members and visitors. The site is built using Plone, an open source web content management system. Plone allows the site to serve as a wiki, to which every user can contribute material. This keeps the membership engaged and spreads the responsibility for the tasks of updating and expanding the site. 2) Email-lists, to engage the broad ocean sciences community. The discussion forums "news," "ask," and "site-help" are available for receiving regular updates on MMI activities, seeking advice or support on projects and standards, or for assistance with using the MMI site. Internal email lists are provided for the Technical Team, the Steering Committee and Executive Committee, and for several content-centered teams. These lists help keep committee members connected, and have been very successful in building consensus and momentum. 3) Regularly scheduled telecons, to provide the chance for interaction between members without the need to physically attend meetings. Both the steering committee and the technical team convene via phone every month. Discussions are guided by agendas published in advance, and minutes are kept on-line for reference. These telecons have been an important tool in moving the MMI project forward; they give members an opportunity for informal discussion and provide a timeframe for accomplishing tasks. 4) Workshops, to make progress towards community agreement, such as the technical workshop "Advancing Domain Vocabularies" August 9-11, 2005, in Boulder, Colorado, where featured domain and metadata experts developed mappings between existing marine metadata vocabularies. Most of the work of the meeting was performed in six small, carefully organized breakout teams, oriented around specific domains. 5) Calendar of events, to keep update the users and where any event related to marine metadata and interoperability can be posted. 6) Specific tools to reach agreements among distributed communities. For example, we developed a tool called Vocabulary Integration Environment (VINE), that allows formalized agreements of mappings across different vocabularies.

Transient Hypothyroidism During Lactation Arrests Myelination in the Anterior Commissure of Rats. A Magnetic Resonance Image and Electron Microscope Study.

PubMed

Lucia, Federico S; Pacheco-Torres, Jesús; González-Granero, Susana; Canals, Santiago; Obregón, María-Jesús; García-Verdugo, José M; Berbel, Pere

2018-01-01

Thyroid hormone deficiency at early postnatal ages affects the cytoarchitecture and function of neocortical and telencephalic limbic areas, leading to impaired associative memory and in a wide spectrum of neurological and mental diseases. Neocortical areas project interhemispheric axons mostly through the corpus callosum and to a lesser extent through the anterior commissure (AC), while limbic areas mostly project through the AC and hippocampal commissures. Functional magnetic resonance data from children with late diagnosed congenital hypothyroidism and abnormal verbal memory processing, suggest altered ipsilateral and contralateral telencephalic connections. Gestational hypothyroidism affects AC development but the possible effect of transient and chronic postnatal hypothyroidism, as occurs in late diagnosed neonates with congenital hypothyroidism and in children growing up in iodine deficient areas, still remains unknown. We studied AC development using in vivo magnetic resonance imaging and electron microscopy in hypothyroid and control male rats. Four groups of methimazole (MMI) treated rats were studied. One group was MMI-treated from postnatal day (P) 0 to P21; some of these rats were also treated with L-thyroxine (T4) from P15 to P21, as a model for early transient hypothyroidism. Other rats were MMI-treated from P0 to P150 and from embryonic day (E) 10 to P170, as a chronic hypothyroidism group. The results were compared with age paired control rats. The normalized T2 signal using magnetic resonance image was higher in MMI-treated rats and correlated with the number and percentage of myelinated axons. Using electron microscopy, we observed decreased myelinated axon number and density in transient and chronic hypothyroid rats at P150, unmyelinated axon number increased slightly in chronic hypothyroid rats. In MMI-treated rats, the myelinated axon g-ratio and conduction velocity was similar to control rats, but with a decrease in conduction delays. These data show that early postnatal transient and chronic hypothyroidism alters AC maturation that may affect the transfer of information through the AC. The alterations cannot be recovered after delayed T4-treatment. Our data support the neurocognitive delay found in late T4-treated children with congenital hypothyroidism.

Differences in Femoral Head Penetration Between Highly Cross-Linked Polyethylene Cemented Sockets and Uncemented Liners.

PubMed

Morita, Daigo; Seki, Taisuke; Higuchi, Yoshitoshi; Takegami, Yasuhiko; Ishiguro, Naoki

2017-12-01

This study aimed at investigating differences in femoral head penetration between highly cross-linked polyethylene (HXLPE) cemented sockets and uncemented liners during 5 years postoperatively. Ninety-six patients (106 hips) with a mean age of 64.4 (range, 35-83) years underwent total hip arthroplasty using a HXLPE cemented socket or liner and were respectively divided into cemented (35 patients [37 hips]) and uncemented (61 patients [69 hips]) groups. Femoral head penetrations were evaluated on both anteroposterior (AP)-view and Lauenstein-view radiographs, and mean polyethylene (PE) wear rates were calculated based on femoral head penetration from 2 to 5 years. Multivariate analyses were performed to assess risk factors for PE wear. At 5 years postoperatively, the cemented and uncemented groups exhibited proximal direction femoral head penetrations of 0.103 mm and 0.124 mm (P = .226) and anterior direction penetrations of 0.090 mm and 0.151 mm (P = .002), respectively. The corresponding mean PE wear rates were 0.004 mm/y and 0.009 mm/y in the AP-view (P = .286) and 0.005 mm/y and 0.012 mm/y in the Lauenstein-view (P = .168), respectively. Left-side operation and high activity were independent risk factors for PE wear on AP-view. When HXLPE was used, all mean PE wear rates were very low and those of cemented sockets and uncemented liners were very similar. PE particle theory suggests that the occurrence of osteolysis and related aseptic loosening might consequently decrease. Copyright © 2017 Elsevier Inc. All rights reserved.

Bilateral medial medullary infarction: a systematic review.

PubMed

Pongmoragot, Jitphapa; Parthasarathy, Sujatha; Selchen, Daniel; Saposnik, Gustavo

2013-08-01

Bilateral infarction of the medial medulla (MMI) is rare. Limited information is available on clinical characteristics, etiology, and prognosis. High-resolution neuroimaging has a major role in elucidating the underlying stroke mechanism. The aim of this systematic review was to analyze the clinical presentations, stroke mechanisms, and outcomes in patients with bilateral MMI. We performed a systematic review of the literature from 1992-2011 that reported on clinical presentations, stroke mechanism, and/or outcomes in patients with magnetic resonance imaging-proven bilateral MMI. Medline, EMBASE, and Web of Science Scholars Portal were searched without language restriction. Two reviewers independently assessed identified studies to determine eligibility, validity, and quality. The primary outcome was inpatient mortality; a secondary outcome was case fatality at 12 months. We identified 138 articles from Medline, EMBASE, and Scholars Portal including the MeSH terms "brainstem infarction," "medulla," and "bilateral." Twenty-nine articles met our inclusion criteria, including a total of 38 cases with bilateral MMI, and included in our study. These 38 patients had a mean age of 62.2 years and were predominately male (74.2%). The most common clinical presentations were motor weakness in 78.4%, dysarthria in 48.6%, and hypoglossal palsy in 40.5%. The most common vascular pathology was vertebral artery atherosclerosis, in 38.5%. The clinical outcome was poor (mortality, 23.8%; dependency, 61.9%). Bilateral medial medullary infarction is a rare stroke syndrome. Clinical presentations were mostly rostral medullary lesions. Large-artery atherosclerosis and branch disease were the most common stroke mechanisms. The clinical outcome was usually poor. Copyright © 2013 National Stroke Association. Published by Elsevier Inc. All rights reserved.

SOI ring resonators with controllable MMI coupler sections

NASA Astrophysics Data System (ADS)

Hu, Youfang; Gardes, Frédéric Y.; Mashanovich, Goran Z.; Reed, Graham T.

2011-01-01

A ring resonator using a single 2×2 MMI as the coupler section has the distinct advantages of low sensitivity to fabrication error, temperature, wavelength and polarisation. However, the coupling coefficient of the 2×2 MMI coupler is fixed; hence, the performance of this type of device is limited, e.g. transmission spectrum with high extinction ratio is difficult to achieve. We have designed and simulated ring resonators with coupler sections consisting of two 2×2 MMIs and phase shifters, so that the coupling efficiency can be varied from 0% to 100% with relative ease. For a single ring resonator, the transmission spectrum can be controlled to achieve an extinction ratio of >20dB and a spectral bandwidth of <1nm. For a multiple ring filter, the transmission spectrum can be controlled to achieve an extinction ratio of >30dB and a bandwidth of <1nm in addition, a flat-top transmission spectrum is also achievable. The whole device has a footprint of approximately 200μm by 100μm.

Practical image registration concerns overcome by the weighted and filtered mutual information metric

NASA Astrophysics Data System (ADS)

Keane, Tommy P.; Saber, Eli; Rhody, Harvey; Savakis, Andreas; Raj, Jeffrey

2012-04-01

Contemporary research in automated panorama creation utilizes camera calibration or extensive knowledge of camera locations and relations to each other to achieve successful results. Research in image registration attempts to restrict these same camera parameters or apply complex point-matching schemes to overcome the complications found in real-world scenarios. This paper presents a novel automated panorama creation algorithm by developing an affine transformation search based on maximized mutual information (MMI) for region-based registration. Standard MMI techniques have been limited to applications with airborne/satellite imagery or medical images. We show that a novel MMI algorithm can approximate an accurate registration between views of realistic scenes of varying depth distortion. The proposed algorithm has been developed using stationary, color, surveillance video data for a scenario with no a priori camera-to-camera parameters. This algorithm is robust for strict- and nearly-affine-related scenes, while providing a useful approximation for the overlap regions in scenes related by a projective homography or a more complex transformation, allowing for a set of efficient and accurate initial conditions for pixel-based registration.

Investigation on the impact of irregular fringe patterns of a single-fiber Mach-Zehnder interferometer on its sensing capabilities

NASA Astrophysics Data System (ADS)

Kumar, Naveen; Kumar, Ashish

2018-07-01

A novel single-mode single-fiber (SMSF) MZI formed by cascading of two non-adiabatic fiber tapers, with stable and repeatable spectrum, has been found to be useful in sensing applications in recent times. A multimode interference based novel simulation approach is proposed to predict the sensing characteristics of SMSF-MZI and is validated with experimental observation. The proposed method includes solving of simultaneous non-homogenous equations for determining the amplitudes of the interfering modes excited in the tapered section of the interferometer. The simulated fringe pattern and the experimental spectral response converge to some important comprehension reported for the first time. A linear shift in output spectral response, of SMSF-MZI, due to change in optical path length induced by temperature/strain etc., is likely to be characterized by three modes interference occurring in the interference region of the interferometer. Whereas if the spectral shift starts saturating at moderately higher temperature/strain, then the formation of interference fringes are possibly governed by two modes interference. Further, it was also explained that a SMSF-MZI with variable fringe widths in its spectral pattern exhibits higher sensitivity than that of the SMSF-MZI having wavelength spectrum with uniform free spectral range. These findings are useful in selecting and predicting the sensitivity of a given SMSF-MZI, based on its spectrum, for sensing applications.

Time-bin entangled photon pairs from spontaneous parametric down-conversion pumped by a cw multi-mode diode laser.

PubMed

Kwon, Osung; Park, Kwang-Kyoon; Ra, Young-Sik; Kim, Yong-Su; Kim, Yoon-Ho

2013-10-21

Generation of time-bin entangled photon pairs requires the use of the Franson interferometer which consists of two spatially separated unbalanced Mach-Zehnder interferometers through which the signal and idler photons from spontaneous parametric down-conversion (SPDC) are made to transmit individually. There have been two SPDC pumping regimes where the scheme works: the narrowband regime and the double-pulse regime. In the narrowband regime, the SPDC process is pumped by a narrowband cw laser with the coherence length much longer than the path length difference of the Franson interferometer. In the double-pulse regime, the longitudinal separation between the pulse pair is made equal to the path length difference of the Franson interferometer. In this paper, we propose another regime by which the generation of time-bin entanglement is possible and demonstrate the scheme experimentally. In our scheme, differently from the previous approaches, the SPDC process is pumped by a cw multi-mode (i.e., short coherence length) laser and makes use of the coherence revival property of such a laser. The high-visibility two-photon Franson interference demonstrates clearly that high-quality time-bin entanglement source can be developed using inexpensive cw multi-mode diode lasers for various quantum communication applications.

Dual spherical single-mode-multimode-single-mode optical fiber temperature sensor based on a Mach–Zehnder interferometer

NASA Astrophysics Data System (ADS)

Tan, Jianchang; Feng, Guoying; Zhang, Shulin; Liang, Jingchuan; Li, Wei; Luo, Yun

2018-07-01

A dual spherical single-mode-multimode-single-mode (DSSMS) optical fiber temperature sensor based on a Mach–Zehnder interferometer (MZI) was designed and implemented in this paper. Theoretical and experimental results indicated that the LP01 mode in the core and the LP09 mode excited by the spherical structure were maintained and transmitted via multimode fiber and interfered at the second spherical structure, resulting in the interference spectrum. An increase or decrease in temperature can cause significant red-shift or blue-shift of the spectrum, respectively. The linearity of the spectral shift due to the temperature change is ~0.999, the sensitivity at 30 °C–540 °C is ~37.372 pm °C‑3, and at  ‑25 °C–25 °C is ~37.28 pm °C‑1. The reproducibility error of this all-fiber temperature sensor at 30 °C–540 °C is less than 0.15%. Compared with the optical fiber sensor with a tapered structure and fiber core offset structure, this MZI-based DSSMS optical fiber temperature sensor has higher mechanical strength. Moreover, benefiting from low-cost and environmentally friendly materials, it is expected to be a novel micro-nano all-fiber sensor.

Thyroid hypoechogenicity after methimazole withdrawal in Graves' disease: a useful index for predicting recurrence?

PubMed

Zingrillo, M; D'Aloiso, L; Ghiggi, M R; Di Cerbo, A; Chiodini, I; Torlontano, M; Liuzzi, A

1996-08-01

A characteristic thyroid ultrasonographic picture with diffuse or scattered low echogenicity has been described in Graves' disease (GD). Thyroid hypoechogenicity in GD at onset has been considered a prognostic index of relapse after medical treatment; moreover, thyroid hypoechogenicity is regularly observed in GD at the onset, but not in patients with 'burned-out' disease. The aim of this study was to evaluate the usefulness of thyroid hypoechogenicity changes in predicting GD relapse. Longitudinal prospective study of previously untreated patients with GD. Thirty-nine consecutive patients aged 10-72 years were treated with methimazole (MMI) for 12-24 months on a titration regimen. Evaluation of patients in remission or with relapse was done 12 and 24 months after MMI withdrawal. Thyroid ultrasonography and TSH receptor antibodies (TRAb) were evaluated in basal conditions and then one month after MMI withdrawal. Thyroid hypoechogenicity score (assessed by the same observer with the same equipment) was graded as: 0 absent; 1 mild; 2 moderate; 3 marked. At the withdrawal evaluation a score < 2 and a TRAb value < 10 U/l were considered as normal. Twelve and 24 months after withdrawal, there were 10 (25.6%) and 17 (44.7%) relapses, respectively. Neither thyroid hypoechogenicity score nor TRAb values evaluated in basal conditions, showed significant differences between patients remaining euthyroid and those who became again hyperthyroid. In the whole group, the thyroid hypoechogenicity score was significantly lower at the withdrawal than in basal conditions (1.1 +/- 1.1 vs 2 +/- 0.8; P < 0.0001); it was significantly lower in patients in remission (P < 0.001), but not in those who relapsed. The thyroid hypoechogenicity score at withdrawal was normal in 23/29 (79.3%) of patients still euthyroid and in 4/10 (40%) of those who relapsed up to the 12th month (P < 0.05); it was normal in 19/21 (90.4%) of patients still euthyroid and in 7/17 (41.2%) of those who relapsed up to the 24th month (P < 0.05). A normal thyroid hypoechogenicity score at withdrawal of MMI had a higher specificity (0.95) and sensitivity (0.59) with respect to TRAb values (0.86 and 0.53, respectively) for the prediction of the relapse of hyperthyroidism at the 24th month. Basal thyroid hypoechogenicity cannot be used as an index of relapse of GD. MMI treatment induces evident changes in thyroid hypoechogenicity, mainly in patients who subsequently go into remission. The absence or a low grade of thyroid hypoechogenicity after MMI treatment seems to be a favourable prognostic index of remission of hyperthyroidism in GD.

[Cost-effectiveness of the clinical treatment of Grave's disease in a public University Hospital: a retrospective analysis and prospective projection for a therapeutic approach].

PubMed

Lima, Nicolau; Knobel, Meyer; Camargo, Rosalinda Y; Tomimori, Eduardo; Medeiros-Neto, Geraldo

2005-08-01

The aim of the present study was to evaluate a new proposal for increasing compliance to the clinical management of patients with Graves' disease (GD) in a large and public University Hospital. The patients were carefully selected (no previous GD treatment, goiter volume less than 6 mL must be living in the metro area of São Paulo), received medication at no cost, were contacted frequently by the social worker and alerted for the date of consultation and only referred to a single endocrinologist during all phases of treatment. We recruited 229 patients with GD that were initially treated with methimazole (MMI--60 mg q.d) in a single daily dose followed by a combination of MMI (20 mg) plus L-T4 (100 microg) daily for 24 months. Only 83 patients (36.2%) completed the protocol and were subdivided in: Group 1 (n= 34) that were in remission for 3 years after discontinuation of the MMI and Group 2 (n= 49) that presented recurrence of GD between 2 and 36 months without MMI. Predictive factors associated with remission were: decrease of the glandular volume, serum TG< 40 ng/mL and normal TRAb values. We concluded that in spite of a careful protocol planned to increase compliance, more than 60% of patients with GD did not complete the therapeutic trial and were referred for radioiodine treatment. The solution for this low therapeutic success for GD should be the possible identification of factors that would indicate patients that are not inclined to follow a long period of clinical therapy.

The incidence of ophthalmopathy after radioiodine therapy for Graves` disease: Prognostic factors and the role of methimazole

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kung, A.W.C.; Cheng, A.

1994-08-01

Radioactive iodine-131 (RAI) has been reported to be associated with a high incidence of development or exacerbation of Graves` ophthalmopathy (GO). This is thought to be associated with a surge of autoantibodies after RAI therapy. The role of methimazole (MMI), which possesses immunomodulatory action, in the prevention of GO was explored by studying 114 patients with Graves` disease. They were assigned randomly to receive either RAI alone or adjunctive antithyroid drugs, which consisted of MMI and L-T{sub 4} as a block-replacement therapy for 12 months and were followed for 2 yr. Thirty-five patients (30.7%) had GO at presentation. Twenty-one (18%)more » patients developed new GO, and six had worsening of preexisting GO. The development of hypothyroidism (P < 0.01) and an elevation of TSH (P < 0.05) were associated with increased risk of development or exacerbation of GO. The chance of development or exacerbation of GO is higher in those with no ophthalmopathy than in those with preexisting GO at presentation (P = 0.002). The incidence of development or exacerbation of GO was similar in the two treatment groups (RAI, 22.8%; adjunctive antithyroid drugs, 23.7%; P = NS). MMI was able to suppress the surge of TSH receptor antibody (TRAB) after RAI, but a surge in TRAB was not of prognostic significance for the development of GO after RAI. Patients who developed or had exacerbation of GO actually had lower TRAB at presentation (P = 0.02). The authors conclude that hypothyroidism with elevated TSH is an important adverse factor for the development or exacerbation of GO, and MMI was unable to prevent the development or exacerbation of GO after RAI. 35 refs., 4 tabs.« less

Mentor-mentee interaction and laboratory social environment: Do they matter in doctoral students' publication productivity?

PubMed

Ynalvez, Marcus Antonius; Ynalvez, Ruby A; Ramírez, Enrique

2017-03-04

We explored the social shaping of science at the micro-level reality of face-to-face interaction in one of the traditional places for scientific activities-the scientific lab. We specifically examined how doctoral students' perception of their: (i) interaction with doctoral mentors (MMI) and (ii) lab social environment (LSE) influenced productivity. Construed as the production of peer-reviewed articles, we measured productivity using total number of articles (TOTAL), number of articles with impact factor greater than or equal to 4.00 (IFGE4), and number of first-authored articles (NFA). Via face-to-face interviews, we obtained data from n = 210 molecular biology Ph.D. students in selected universities in Japan, Singapore, and Taiwan. Additional productivity data (NFA) were obtained from online bibliometric databases. To summarize the original 13 MMI and 13 LSE semantic-differential items which we used to measure students' perceptions, principal component (PC) analyses were performed. The results were smaller sets of 4 MMI PCs and 4 LSE PCs. To identify which PCs influenced publication counts, we performed Poisson regression analyses. Although perceived MMI was not linked to productivity, perceived LSE was linked: Students who perceived their LSE as intellectually stimulating reported high levels of productivity in both TOTAL and IFGE4, but not in NFA. Our findings not only highlight how students' perception of their training environment factors in the production of scientific output, our findings also carry important implications for improving mentoring programs in science. © 2016 by The International Union of Biochemistry and Molecular Biology, 45(2):130-144, 2017. © 2016 The International Union of Biochemistry and Molecular Biology.

The MMI Semantic Framework: Rosetta Stones for Earth Sciences

NASA Astrophysics Data System (ADS)

Rueda, C.; Bermudez, L. E.; Graybeal, J.; Alexander, P.

2009-12-01

Semantic interoperability—the exchange of meaning among computer systems—is needed to successfully share data in Ocean Science and across all Earth sciences. The best approach toward semantic interoperability requires a designed framework, and operationally tested tools and infrastructure within that framework. Currently available technologies make a scientific semantic framework feasible, but its development requires sustainable architectural vision and development processes. This presentation outlines the MMI Semantic Framework, including recent progress on it and its client applications. The MMI Semantic Framework consists of tools, infrastructure, and operational and community procedures and best practices, to meet short-term and long-term semantic interoperability goals. The design and prioritization of the semantic framework capabilities are based on real-world scenarios in Earth observation systems. We describe some key uses cases, as well as the associated requirements for building the overall infrastructure, which is realized through the MMI Ontology Registry and Repository. This system includes support for community creation and sharing of semantic content, ontology registration, version management, and seamless integration of user-friendly tools and application programming interfaces. The presentation describes the architectural components for semantic mediation, registry and repository for vocabularies, ontology, and term mappings. We show how the technologies and approaches in the framework can address community needs for managing and exchanging semantic information. We will demonstrate how different types of users and client applications exploit the tools and services for data aggregation, visualization, archiving, and integration. Specific examples from OOSTethys (http://www.oostethys.org) and the Ocean Observatories Initiative Cyberinfrastructure (http://www.oceanobservatories.org) will be cited. Finally, we show how semantic augmentation of web services standards could be performed using framework tools.

Considerations in comparing the U.S. Geological Survey one‐year induced‐seismicity hazard models with “Did You Feel It?” and instrumental data

USGS Publications Warehouse

White, Isabel; Liu, Taojun; Luco, Nicolas; Liel, Abbie

2017-01-01

The recent steep increase in seismicity rates in Oklahoma, southern Kansas, and other parts of the central United States led the U.S. Geological Survey (USGS) to develop, for the first time, a probabilistic seismic hazard forecast for one year (2016) that incorporates induced seismicity. In this study, we explore a process to ground‐truth the hazard model by comparing it with two databases of observations: modified Mercalli intensity (MMI) data from the “Did You Feel It?” (DYFI) system and peak ground acceleration (PGA) values from instrumental data. Because the 2016 hazard model was heavily based on earthquake catalogs from 2014 to 2015, this initial comparison utilized observations from these years. Annualized exceedance rates were calculated with the DYFI and instrumental data for direct comparison with the model. These comparisons required assessment of the options for converting hazard model results and instrumental data from PGA to MMI for comparison with the DYFI data. In addition, to account for known differences that affect the comparisons, the instrumental PGA and DYFI data were declustered, and the hazard model was adjusted for local site conditions. With these adjustments, examples at sites with the most data show reasonable agreement in the exceedance rates. However, the comparisons were complicated by the spatial and temporal completeness of the instrumental and DYFI observations. Furthermore, most of the DYFI responses are in the MMI II–IV range, whereas the hazard model is oriented toward forecasts at higher ground‐motion intensities, usually above about MMI IV. Nevertheless, the study demonstrates some of the issues that arise in making these comparisons, thereby informing future efforts to ground‐truth and improve hazard modeling for induced‐seismicity applications.

Characteristics of stroke mechanisms in patients with medullary infarction.

PubMed

Lee, M J; Park, Y G; Kim, S J; Lee, J J; Bang, O Y; Kim, J S

2012-11-01

Few studies have focused on the mechanisms underlying medullary infarctions. Our aim in this study was to investigate stroke mechanisms in patients with medullary infarctions and to determine the clinical, radiological and laboratory characteristics of these patients with different underlying stroke etiologies. Consecutive patients with medullary infarction were analysed. Stroke mechanisms were classified as large artery disease (LAD), cardiogenic embolism (CE), small vessel disease (SVD), arterial dissection or undetermined etiology. Clinical, radiological and laboratory factors were analysed according to the location of the lesion and stroke mechanisms. A total of 77 patients were enrolled in this study. Amongst them, 53 (68.8%) patients had lateral medullary infarction (LMI), 22 (28.6%) had medial medullary infarction (MMI), and the remaining 2 (2.6%) had hemimedullary infarction. In both LMI and MMI patients, LAD was the most frequently encountered stroke mechanism. Arterial dissection was the second most common cause followed by SVD and CE in patients with LMI, whereas SVD was more frequently observed (P < 0.001) and dissection and CE were less prevalent (P < 0.001 and P = 0.024, respectively) in MMI than in LMI. Regarding differences amongst stroke etiologies, patients with dissection were younger and had a significantly lower incidence of metabolic syndrome (P = 0.002 and P = 0.009, respectively) than patients with LAD and SVD. Patients in the LAD (19/34, 60%) and dissection groups (12/14, 75%) had abnormal perfusion-weighted MRI (PWI) findings, whereas all patients with SVD (9/9) had normal PWI findings (P < 0.001). Stroke mechanisms in medullary infarction differ between LMI and MMI. Clinical and radiological characteristics, especially PWI features, are helpful in discriminating the etiologies of stroke in these patients. © 2012 The Author(s) European Journal of Neurology © 2012 EFNS.

Development of a diatom-based multimetric index for acid mine drainage impacted depressional wetlands.

PubMed

Riato, Luisa; Leira, Manel; Della Bella, Valentina; Oberholster, Paul J

2018-01-15

Acid mine drainage (AMD) from coal mining in the Mpumalanga Highveld region of South Africa has caused severe chemical and biological degradation of aquatic habitats, specifically depressional wetlands, as mines use these wetlands for storage of AMD. Diatom-based multimetric indices (MMIs) to assess wetland condition have mostly been developed to assess agricultural and urban land use impacts. No diatom MMI of wetland condition has been developed to assess AMD impacts related to mining activities. Previous approaches to diatom-based MMI development in wetlands have not accounted for natural variability. Natural variability among depressional wetlands may influence the accuracy of MMIs. Epiphytic diatom MMIs sensitive to AMD were developed for a range of depressional wetland types to account for natural variation in biological metrics. For this, we classified wetland types based on diatom typologies. A range of 4-15 final metrics were selected from a pool of ~140 candidate metrics to develop the MMIs based on their: (1) broad range, (2) high separation power and (3) low correlation among metrics. Final metrics were selected from three categories: similarity to reference sites, functional groups, and taxonomic composition, which represent different aspects of diatom assemblage structure and function. MMI performances were evaluated according to their precision in distinguishing reference sites, responsiveness to discriminate reference and disturbed sites, sensitivity to human disturbances and relevancy to AMD-related stressors. Each MMI showed excellent discriminatory power, whether or not it accounted for natural variation. However, accounting for variation by grouping sites based on diatom typologies improved overall performance of MMIs. Our study highlights the usefulness of diatom-based metrics and provides a model for the biological assessment of depressional wetland condition in South Africa and elsewhere. Copyright © 2017 Elsevier B.V. All rights reserved.

A multi-core fiber based interferometer for high temperature sensing

NASA Astrophysics Data System (ADS)

Zhou, Song; Huang, Bo; Shu, Xuewen

2017-04-01

In this paper, we have verified and implemented a Mach-Zehnder interferometer based on seven-core fiber for high temperature sensing application. This proposed structure is based on a multi-mode-multi-core-multi-mode fiber structure sandwiched by a single mode fiber. Between the single-mode and multi-core fiber, a 3 mm long multi-mode fiber is formed for lead-in and lead-out light. The basic operation principle of this device is the use of multi-core modes, single-mode and multi-mode interference coupling is also utilized. Experimental results indicate that this interferometer sensor is capable of accurate measurements of temperatures up to 800 °C, and the temperature sensitivity of the proposed sensor is as high as 170.2 pm/°C, which is much higher than the current existing MZI based temperature sensors (109 pm/°C). This type of sensor is promising for practical high temperature applications due to its advantages including high sensitivity, simple fabrication process, low cost and compactness.

Sensitivity-Bandwidth Limit in a Multimode Optoelectromechanical Transducer

NASA Astrophysics Data System (ADS)

Moaddel Haghighi, I.; Malossi, N.; Natali, R.; Di Giuseppe, G.; Vitali, D.

2018-03-01

An optoelectromechanical system formed by a nanomembrane capacitively coupled to an L C resonator and to an optical interferometer has recently been employed for the highly sensitive optical readout of rf signals [T. Bagci et al., Nature (London) 507, 81 (2013), 10.1038/nature13029]. We propose and experimentally demonstrate how the bandwidth of such a transducer can be increased by controlling the interference between two electromechanical interaction pathways of a two-mode mechanical system. With a proof-of-principle device operating at room temperature, we achieve a sensitivity of 300 nV /√{Hz } over a bandwidth of 15 kHz in the presence of radio-frequency noise, and an optimal shot-noise-limited sensitivity of 10 nV /√{Hz } over a bandwidth of 5 kHz. We discuss strategies for improving the performance of the device, showing that, for the same given sensitivity, a mechanical multimode transducer can achieve a bandwidth significantly larger than that for a single-mode one.

1x3 beam splitter for TE polarization based on self-imaging phenomena in photonic crystal waveguides.

PubMed

Zhang, Min; Malureanu, Radu; Krüger, Asger Christian; Kristensen, Martin

2010-07-05

Based on inspiration from multi-mode interference self-imaging and theoretical FDTD simulations, a 1x3 beam splitter was designed, fabricated and characterized. Measurements show that for TE-polarized incident light the power is distributed equally between the output ports within 1dB in the range from 1541nm to 1552nm, and the total transmission of the 1x3 splitter is equal to the corresponding length of a single-line-defect PhCW within the measurement uncertainty.

Dynamical Casimir Effect for Gaussian Boson Sampling.

PubMed

Peropadre, Borja; Huh, Joonsuk; Sabín, Carlos

2018-02-28

We show that the Dynamical Casimir Effect (DCE), realized on two multimode coplanar waveg-uide resonators, implements a gaussian boson sampler (GBS). The appropriate choice of the mirror acceleration that couples both resonators translates into the desired initial gaussian state and many-boson interference in a boson sampling network. In particular, we show that the proposed quantum simulator naturally performs a classically hard task, known as scattershot boson sampling. Our result unveils an unprecedented computational power of DCE, and paves the way for using DCE as a resource for quantum simulation.

Effect of hearing loss on semantic access by auditory and audiovisual speech in children.

PubMed

Jerger, Susan; Tye-Murray, Nancy; Damian, Markus F; Abdi, Hervé

2013-01-01

This research studied whether the mode of input (auditory versus audiovisual) influenced semantic access by speech in children with sensorineural hearing impairment (HI). Participants, 31 children with HI and 62 children with normal hearing (NH), were tested with the authors' new multimodal picture word task. Children were instructed to name pictures displayed on a monitor and ignore auditory or audiovisual speech distractors. The semantic content of the distractors was varied to be related versus unrelated to the pictures (e.g., picture distractor of dog-bear versus dog-cheese, respectively). In children with NH, picture-naming times were slower in the presence of semantically related distractors. This slowing, called semantic interference, is attributed to the meaning-related picture-distractor entries competing for selection and control of the response (the lexical selection by competition hypothesis). Recently, a modification of the lexical selection by competition hypothesis, called the competition threshold (CT) hypothesis, proposed that (1) the competition between the picture-distractor entries is determined by a threshold, and (2) distractors with experimentally reduced fidelity cannot reach the CT. Thus, semantically related distractors with reduced fidelity do not produce the normal interference effect, but instead no effect or semantic facilitation (faster picture naming times for semantically related versus unrelated distractors). Facilitation occurs because the activation level of the semantically related distractor with reduced fidelity (1) is not sufficient to exceed the CT and produce interference but (2) is sufficient to activate its concept, which then strengthens the activation of the picture and facilitates naming. This research investigated whether the proposals of the CT hypothesis generalize to the auditory domain, to the natural degradation of speech due to HI, and to participants who are children. Our multimodal picture word task allowed us to (1) quantify picture naming results in the presence of auditory speech distractors and (2) probe whether the addition of visual speech enriched the fidelity of the auditory input sufficiently to influence results. In the HI group, the auditory distractors produced no effect or a facilitative effect, in agreement with proposals of the CT hypothesis. In contrast, the audiovisual distractors produced the normal semantic interference effect. Results in the HI versus NH groups differed significantly for the auditory mode, but not for the audiovisual mode. This research indicates that the lower fidelity auditory speech associated with HI affects the normalcy of semantic access by children. Further, adding visual speech enriches the lower fidelity auditory input sufficiently to produce the semantic interference effect typical of children with NH.

The distribution of modified mercalli intensity in the 18 April 1906 San Francisco earthquake

USGS Publications Warehouse

Boatwright, J.; Bundock, H.

2008-01-01

We analyze Boatwright and Bundock's (2005) modified Mercalli intensity (MMI) map for the 18 April 1906 San Francisco earthquake, reviewing their interpretation of the MMI scale and testing their correlation of 1906 cemetery damage with MMI intensity. We consider in detail four areas of the intensity map where Boatwright and Bundock (2005) added significantly to the intensity descriptions compiled by Lawson (1908). We show that the distribution of off-fault damage in Sonoma County suggests that the rupture velocity approached the P-wave velocity along Tomales Bay. In contrast, the falloff of intensity with distance from the fault appears approximately constant throughout Mendocino County. The intensity in Humboldt County appears somewhat higher than the intensity in Mendocino County, suggesting that the rupture process at the northern end of the rupture was relatively energetic and that there was directivity consistent with a subsonic rupture velocity on the section of the fault south of Shelter Cove. Finally, we show that the intensity sites added in Santa Cruz County change the intensity distribution so that it decreases gradually along the southeastern section of rupture from Corralitos to San Juan Bautista and implies that the stress release on this section of rupture was relatively low.

Effect of cloric acid concentration on corrosion behavior of Ni/Cr coated on carbon steel

NASA Astrophysics Data System (ADS)

Desiati, Resetiana Dwi; Sugiarti, Eni; Thosin, K. A. Zaini

2018-05-01

Corrosion is one of the causes of metal degradation. Carbon steel (Fe) is easy to corrode in the extreme environment. Coating on carbon steel is required to improve corrosion resistance owing to protection or hindrance to extreme environmental conditions. In this present work, carbon steel was coated by electroplating techniques for nickel and pack cementation for chrome. The corrosion rate test was performed by Weight Loss method on FeNiCr, FeNi, FeCr and uncoated Fe as comparator which was dyed in 37% HCl and 25% HCl which had previously been measured dimension and mass. The immersion test result of FeNiCr and FeNi specimen were better than FeCr and uncoated Fe in terms of increasing corrosion resistance. The corrosion rate for 56 hours in 37% HCl for FeNiCr was 1.592 mm/y and FeNi was 3.208 mm/y, FeCr only lasted within 32 hours with corrosion rate was 6.494 mm/y. Surface of the sample after the corrosion test there was pitting, crevice corrosion and alloy cracking caused by chloride. The higher the concentration of HCl the faster the corrosion rate.

Mayaro Virus Infection in Amazonia: A Multimodel Inference Approach to Risk Factor Assessment

PubMed Central

de Paula, Vanessa S.; Figueiredo, Luiz T. M.; Braga, Wornei S. M.; Luz, Sérgio L. B.

2012-01-01

Background Arboviral diseases are major global public health threats. Yet, our understanding of infection risk factors is, with a few exceptions, considerably limited. A crucial shortcoming is the widespread use of analytical methods generally not suited for observational data – particularly null hypothesis-testing (NHT) and step-wise regression (SWR). Using Mayaro virus (MAYV) as a case study, here we compare information theory-based multimodel inference (MMI) with conventional analyses for arboviral infection risk factor assessment. Methodology/Principal Findings A cross-sectional survey of anti-MAYV antibodies revealed 44% prevalence (n = 270 subjects) in a central Amazon rural settlement. NHT suggested that residents of village-like household clusters and those using closed toilet/latrines were at higher risk, while living in non-village-like areas, using bednets, and owning fowl, pigs or dogs were protective. The “minimum adequate” SWR model retained only residence area and bednet use. Using MMI, we identified relevant covariates, quantified their relative importance, and estimated effect-sizes (β±SE) on which to base inference. Residence area (β Village = 2.93±0.41; β Upland = −0.56±0.33, β Riverbanks = −2.37±0.55) and bednet use (β = −0.95±0.28) were the most important factors, followed by crop-plot ownership (β = 0.39±0.22) and regular use of a closed toilet/latrine (β = 0.19±0.13); domestic animals had insignificant protective effects and were relatively unimportant. The SWR model ranked fifth among the 128 models in the final MMI set. Conclusions/Significance Our analyses illustrate how MMI can enhance inference on infection risk factors when compared with NHT or SWR. MMI indicates that forest crop-plot workers are likely exposed to typical MAYV cycles maintained by diurnal, forest dwelling vectors; however, MAYV might also be circulating in nocturnal, domestic-peridomestic cycles in village-like areas. This suggests either a vector shift (synanthropic mosquitoes vectoring MAYV) or a habitat/habits shift (classical MAYV vectors adapting to densely populated landscapes and nocturnal biting); any such ecological/adaptive novelty could increase the likelihood of MAYV emergence in Amazonia. PMID:23071852

Diffraction of entangled particles by light gratings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sancho, Pedro, E-mail: psanchos@aemet.es

We analyze the diffraction regime of the Kapitza–Dirac effect for particles entangled in momentum. The detection patterns show two-particle interferences. In the single-mode case we identify a discontinuity in the set of joint detection probabilities, associated with the disconnected character of the space of non-separable states. For Gaussian multi-mode states we derive the diffraction patterns, providing an example of the dependence of the light–matter interaction on entanglement. When the particles are identical, we can explore the relation between exchange and entanglement effects. We find a complementary behavior between overlapping and Schmidt’s number. In particular, symmetric entanglement can cancel the exchangemore » effects. - Highlights: • Kapitza–Dirac diffraction of entangled particles shows multiparticle interference. • There is a discontinuity in the set of joint detection patterns of entangled states. • We find a complementary behavior between overlapping and Schmidt’s number. • Symmetric entanglement can cancel the exchange effects.« less

High temperature fiber sensor using the interference effect within a suspended core microstructured optical fiber

NASA Astrophysics Data System (ADS)

Nguyen, Linh V.; Warren-Smith, Stephen C.; Ebendorff-Heidepriem, Heike; Monro, Tanya M.

2016-04-01

We report a high temperature fiber sensor based on the multimode interference effect within a suspended core microstructured optical fiber (SCF). By splicing a short section of SCF with a lead-in single-mode fiber (SMF), the sensor head was formed. A complex interference pattern was obtained in the reflection spectrum as the result of the multiple excited modes in the SCF. The complexity of the interference indicates that there are more than two dominantly excited modes in the SCF, as resolved by Fast Fourier Transform (FFT) analysis of the interference. The proposed sensor was subjected to temperature variation from 20°C to 1100°C. The fringe of the filtered spectrum red-shifted linearly with respect to temperature varying between 20°C and 1100°C, with similar temperature sensitivity for increasing and decreasing temperature. Phase monitoring was used for an extended temperature experiment (80 hours) in which the sensor was subjected to several different temperature variation conditions namely (i) step-wise increase/decrease with 100°C steps between 20°C and 1100°C, (ii) dwelling overnight at 400°C, (iii) free fall from 1100°C to 132°C, and (iv) continuous increase of temperature from 132°C to 1100°C. Our approach serves as a simple and cost-effective alternative to the better-known high temperature fiber sensors such as the fiber Bragg grating (FBG) in sapphire fibers or regenerated FBG in photosensitive optical fibers.

Synthesis and radiolabeling of a somatostatin analog for multimodal imaging

NASA Astrophysics Data System (ADS)

Edwards, W. Barry; Liang, Kexian; Xu, Baogang; Anderson, Carolyn J.; Achilefu, Samuel

2006-02-01

A new multimodal imaging agent for imaging the somatostatin receptor has been synthesized and evaluated in vitro and in vivo. A somatostatin analog, conjugated to both 1,4,7,10-tetraazacyclododecane-1,4,7,10-tetraaceticacid (DOTA) and cypate (BS-296), was synthesized entirely on the solid phase (Fmoc) and purified by RP-HPLC. DOTA was added as a ligand for radiometals such as 64Cu or 177Lu for either radio-imaging or radiotherapy respectively. Cytate, a cypatesomatostatin analog conjugate, has previously demonstrated the ability to visualize somatostatin receptor rich tumor xenografts and natural organs by optical imaging techniques. BS-296 exhibited low nanomolar inhibitory capacity toward the binding of radiolabeled somatostatin analogs in cell membranes enriched in the somatostatin receptor, demonstrating the high affinity of this multimodal imaging peptide and indicating its potential as a molecular imaging agent. 64Cu, an isotope for diagnostic imaging and radiotherapy, was selected as the isotope for radiolabeling BS-296. BS-296 was radiolabeled with 64Cu in high specific activity (200 μCi/μg) in 90% radiochemical yield. Addition of 2,5-dihydroxybenzoic acid (gentisic acid) prevented radiolysis of the sample, allowing for study of the 64Cu -BS-296 the day following radiolabeling. Furthermore, inclusion of DMSO at a level of 20% was found not to interfere with radiolabeling yields and prevented the adherence of 64Cu -BS-296 to the walls of the reaction vessel.

Cancer Theranostics with Near-Infrared Light-Activatable Multimodal Nanoparticles

PubMed Central

Melancon, Marites P.; Zhou, Min; Li, Chun

2011-01-01

CONSPECTUS Nanomaterials that interact with light provide a unique opportunity for biophotonic nanomedicine. Multifunctional nanoparticles (NPs) that have strong and tunable surface plasmon resonance absorption in the near-infrared region combined with visibility with multiple imaging modalities (magnetic resonance imaging, nuclear imaging, and photoacoustic imaging) have great potential in image-guided therapies. These novel nanostructures, once introduced, are expected to home to solid tumors via the enhanced permeability and retention effect (a passive targeting mechanism) or via targeting ligands bound to their surfaces (an active targeting mechanism). The primary mode of action for photothermal conducting NPs is to convert photoenergy into heat, causing temperature in the treatment volume to be elevated above the thermal damage threshold, which results in irreversible cell killing. It is now recognized that this process, termed photothermal ablation therapy or PTA, although very effective, is unlikely to kill all tumor cells when used alone. In addition to PTA, photothermal conducting NPs can also efficiently trigger drug release and activate RNA interference. Such a multimodal approach, which permits simultaneous PTA therapy, chemotherapy, and therapeutic RNA interference, should provide an opportunity for complete eradication of residual disease. In this Account, we provide an up-to-date review of the synthesis and characterization, functionalization, and in vitro and in vivo evaluation of NIR light-activatable multifunctional nanostructures used for imaging and therapy, with an emphasis on hollow gold nanospheres, magnetic core–shell gold nanoshells, and semiconductor copper monosulfide NPs. We discuss three types novel drug delivery systems in which hollow gold nanospheres are used to mediate controlled drug release. PMID:21848277

Microgrid and Inverter Control and Simulator Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

2012-09-13

A collection of software that can simulate the operation of an inverter on a microgrid or control a real inverter. In addition, it can simulate the control of multiple nodes on a microgrid." Application: Simulation of inverters and microgrids; control of inverters on microgrids." The MMI submodule is designed to control custom inverter hardware, and to simulate that hardware. The INVERTER submodule is only the simulator code, and is of an earlier generation than the simulator in MMI. The MICROGRID submodule is an agent-based simulator of multiple nodes on a microgrid which presents a web interface. The WIND submodule producesmore » movies of wind data with a web interface.« less

Medical treatment of hyperthyroidism: state of the art.

PubMed

Fumarola, A; Di Fiore, A; Dainelli, M; Grani, G; Calvanese, A

2010-11-01

Methimazole (MMI) and propylthiouracil (PTU) are the main antithyroid drugs used for hyperthyroidism. They inhibit the synthesis of thyroid hormone at various levels and are used as the primary treatment for hyperthyroidism or as a preparation before radioiodine therapy or thyroidectomy. MMI is the drug of choice because of its widespread availability, longer half-life and small number of severe side effects. Drugs of second choice are potassium perchlorate, beta blockers, iodine, lithium carbonate and glucocorticoids. Rituximab, a monoclonal antibody directed against human CD20, was recently proposed as a biological therapy for cases of Graves' disease unresponsive to traditional drugs. © J. A. Barth Verlag in Georg Thieme Verlag KG Stuttgart · New York.

Transient polyuria related to central diabetes insipidus caused by lymphocytic infundibulo-neurohypophysitis in a patient treated for Graves' disease.

PubMed

Yamazaki, Masanori; Sato, Ai; Nishio, Shin-ichi; Uehara, Takeshi; Komatsu, Mitsuhisa

2010-01-01

A 45-year-old man was hospitalized because of weight loss, finger tremor, thirst, polydipsia and increased urinary frequency. He was diagnosed with Graves' disease (GD) and central diabetes insipidus (CDI). Magnetic resonance imaging revealed the enlarged posterior pituitary with thickened stalk. Histological examination obtained from biopsy of the pituitary revealed lymphocytic infundibulo-neurohypophysitis. He received treatment with thiamazole (MMI) for GD and desmopressin acetate (DDAVP) for CDI. However, DDAVP administration could be discontinued as GD was gradually improved. This course indicates that not only the recovered renal response to arginine-vasopressin but also the immunomodulative effects of MMI might attribute to the improvement of polyuria.

Early return to work in workers' compensation patients after arthroscopic full-thickness rotator cuff repair.

PubMed

Bhatia, Sanjeev; Piasecki, Dana P; Nho, Shane Jay; Romeo, Anthony A; Cole, Brian J; Nicholson, Gregory P; Boniquit, Nicole; Verma, Nikhil N

2010-08-01

The purpose of this study was to investigate the ability of patients to return to their preoperative work level and to identify functional prognostic factors in a group of Workers' Compensation (WC) patients after arthroscopic repair of full-thickness rotator cuff tears at a minimum follow-up of 1 year. Seventy-eight consecutive WC patients underwent arthroscopic rotator cuff repair (ARCR) and were retrospectively reviewed. Potential predictors of occupational outcomes were recorded. The primary outcomes included work level at the time of discharge, time to maximum medical improvement (MMI), and failures requiring revision rotator cuff repair. Secondary outcomes including physical examination and subjective scoring scales were also recorded. Overall, 88.5% of patients (n = 69) returned to their preoperative level of work at a mean time to MMI of 7.6 +/- 2.6 months. Of the WC patients, 55 (70.5%) were followed up for purposes of assessing shoulder function, with a mean follow-up of 33.6 +/- 13.9 months. The mean American Shoulder and Elbow Surgeons score at this time was 82.3 +/- 20.9, and the mean score on a visual analog scale was 1.7 +/- 2.3. An association was found between patients who underwent ARCR with open biceps tenodesis and delay in MMI (P = .01). WC patients undergoing ARCR may expect a high likelihood of return to full duty at a mean time to MMI of 7.6 months. At the time of follow-up, patients reported good outcomes using validated scoring scales, but subjective outcomes remained inferior to non-WC patients based on historical controls. Alcohol use was the only prognostic factor to show a significant association with return to restricted-duty employment and repair failure. Level IV, therapeutic case series. 2010 Arthroscopy Association of North America. Published by Elsevier Inc. All rights reserved.

Anti-glutamic acid decarboxylase antibody in Graves' disease is a possible indicator for the unlikelihood of going into remission with antithyroid agents.

PubMed

Yoshihara, Ai; Isozaki, Osamu; Okubo, Yumiko; Takano, Kazue

2009-01-01

The prevalence and titer of glutamic acid decarboxylase antibody (GADAb) in type 1 diabetes mellitus (T1DM) has been reported to be higher in patients with autoimmune thyroid diseases (AITD) than those without them. However, we have no data about the influence of GADAb on AITD. We therefore studied the clinical characteristics of Graves' disease (GD) with GADAb in order to clarify the influence of GADAb on GD. Twelve GD patients with GADAb were enrolled and were compared to 40 GD patients without DM. The male to female ratio and age of onset of GD showed no statistical difference. The titer of TSH receptor antibody (TRAb) at the onset of GD was similar in both groups. Initial treatment with methimazole (MMI) was started in all patients with GADAb but radioactive iodine (RI) therapy was carried out in five patients because of adverse effects of MMI or poor control of hyperthyroidism. The initial titer of TRAb was significantly lower in patients treated with MMI alone compared to that in RI treated patients but none of the patients treated with MMI alone went into remission after more than 3-years of follow up. We also compared these GADAb-positive patients with 14 patients with diabetes mellitus who had matched clinical features. The number of diabetic patients who remained in possible remission was significantly higher than that of GADAb-positive patients (5 in 14 vs 0 in 12). Moreover, the rate of remission in the diabetic patients was no different from that of 21 control patients without diabetes followed for more than 7 years (5 in 14 vs 7 in 21). These data suggested that GADAb-positive patients are unlikely to go into remission with antithyroid agents. Therefore, definitive therapies might be preferable for the initial treatment of GADAb-positive patients.

Antithyroid Drugs and Congenital Malformations: A Nationwide Korean Cohort Study.

PubMed

Seo, Gi Hyeon; Kim, Tae Hyuk; Chung, Jae Hoon

2018-03-20

Untreated or insufficiently treated Graves disease in pregnancy may pose risks to both mother and fetus. Antithyroid drugs (ATDs) are the treatment mainstay, but the potential teratogenic effect of these drugs has prompted clinicians to question the safe management of this vulnerable population. To examine the association between maternal prescriptions for ATDs and congenital malformations in live births. Nationwide cohort study. Korean National Health Insurance database. A cohort of 2 886 970 completed pregnancies linked to live-born infants in 2 210 253 women between 2008 and 2014. Maternal prescriptions for ATDs in the first trimester. The risk for overall and organ-specific congenital malformations in offspring, with logistic regression models used to control for potential confounders. 12 891 pregnancies (0.45%) were exposed to ATDs during the first trimester. The prevalence of malformations in exposed offspring was 7.27%, compared with 5.94% in offspring of women who were not prescribed ATDs during pregnancy (P < 0.001) (adjusted odds ratio, 1.19 [95% CI, 1.12 to 1.28]). Absolute increases in the prevalence of congenital malformations per 1000 live births were 8.81 cases (CI, 3.92 to 13.70 cases) for propylthiouracil alone, 17.05 cases (CI, 1.94 to 32.15 cases) for methimazole (MMI) alone, and 16.53 cases (CI, 4.73 to 28.32 cases) for propylthiouracil and MMI, compared with pregnancies without ATD prescriptions. In the MMI group, a high cumulative dose (>495 mg) during the first trimester was associated with an increased risk for malformations compared with a low dose (1 to 126 mg) (adjusted odds ratio, 1.87 [CI, 1.06 to 3.30]). The study used a prescription claims database to assess ATD exposure. Exposure to ATDs during the first trimester was associated with increased risk for congenital malformations, particularly for pregnancies in which women received prescriptions for MMI or both ATDs. None.

Mechanical Structural Design of a MEMS-Based Piezoresistive Accelerometer for Head Injuries Monitoring: A Computational Analysis by Increments of the Sensor Mass Moment of Inertia †

PubMed Central

Messina, Marco; Njuguna, James; Palas, Chrysovalantis

2018-01-01

This work focuses on the proof-mass mechanical structural design improvement of a tri-axial piezoresistive accelerometer specifically designed for head injuries monitoring where medium-G impacts are common; for example, in sports such as racing cars or American Football. The device requires the highest sensitivity achievable with a single proof-mass approach, and a very low error (<1%) as the accuracy for these types of applications is paramount. The optimization method differs from previous work as it is based on the progressive increment of the sensor proof-mass mass moment of inertia (MMI) in all three axes. Three different designs are presented in this study, where at each step of design evolution, the MMI of the sensor proof-mass gradually increases in all axes. The work numerically demonstrates that an increment of MMI determines an increment of device sensitivity with a simultaneous reduction of cross-axis sensitivity in the particular axis under study. This is due to the linkage between the external applied stress and the distribution of mass (of the proof-mass), and therefore of its mass moment of inertia. Progressively concentrating the mass on the axes where the piezoresistors are located (i.e., x- and y-axis) by increasing the MMI in the x- and y-axis, will undoubtedly increase the longitudinal stresses applied in that areas for a given external acceleration, therefore increasing the piezoresistors fractional resistance change and eventually positively affecting the sensor sensitivity. The final device shows a sensitivity increase of about 80% in the z-axis and a reduction of cross-axis sensitivity of 18% respect to state-of-art sensors available in the literature from a previous work of the authors. Sensor design, modelling, and optimization are presented, concluding the work with results, discussion, and conclusion. PMID:29351221

SARCOSPA - Sarcopenia in spondyloarthritis patients.

PubMed

Aguiar, R; Sequeira, J; Meirinhos, T; Ambrósio, C; Barcelos, A

2014-01-01

The loss of muscle mass (MM) is a serious problem which has been demonstrated in patients with rheumatoid arthritis. There are few studies about the loss of MM in patients with spondyloarthritis (Spa). To assess muscle mass index (MMI) in a cohort of patients with Spa and compare it with a control group of healthy individuals; to verify if a higher risk of sarcopenia is related with disease activity, functional impairment, duration of the illness and radiological damage. Case control study. Muscle mass index (MMI) was determined, from the value of MM, using Lee's equation, in a cohort of patients with spondyloarthritis and in a control group. Bath Ankylosing Spondylitis Disease Activity and Function Indexes (BASDAI and BASFI), Ankylosing Spondylitis Quality of Life (ASQoL) and Modified Stoke Ankylosing Spondylitis Spinal Score (mSASSS) were assessed in a cohort of patients with axial Spa, as well as Health Assessment Questionnaire (HAQ) and Disease Activity Score 28 (DAS28) in patients with peripheral disease. Data were treated using SPSS version 17.0. Values of p<0,05 were considered with statistical significance. 60 patients were enrolled; 48.2% were males, mean age 45.5±13.4 years, mean disease duration 10.9±11.6 years; 36 had ankylosing spondylitis and 24 had psoriatic arthritis. 62% of patients had sarcopenia and there was a significant difference in mean MMI between patients and controls (7.65±0.98 vs 8.25±0.92; p=0.001, OR =5.23. In male patients, there was a statistically significant moderate negative correlation between MMI and BASDAI and BASFI (p=-0.536 and p=-0.445). No other significant correlations were identified. Our study supports the hypothesis of a greater prevalence of sarcopenia in patients with Spa compared to healthy controls. Some limitations included the sample size, potential confounding factor such the bias of measurement and the use of a non-validated equation to Portuguese population to calculate MM.

Slow Long-Term Erosion Rates of Banks Peninsula, New Zealand

NASA Astrophysics Data System (ADS)

Dudunake, T.; Nichols, K. K.; Pugsley, E.; Nelson, S.; Colton, J.

2017-12-01

Banks Peninsula, located south of Christchurch, New Zealand, is composed of a multi-aged complex of volcanic centers. The oldest, Lyttelton Volcano is 12 to 10 Ma, and 350 km3. The largest volcano, Akaroa Volcano, is 9 to 8 Ma and 1200 km3. Both of these volcanoes have large embayments (Lyttelton Harbour and Akaroa Harbour) that connect the central volcano (the location of the former volcanic summits) to the ocean. The other eruptive centers, Mt. Herbert ( 9.5 to 8 Ma) and Diamond Harbor (7 to 5.8 Ma), have not eroded to sea level. We used inferred original surfaces and present day topography to calculate the volume of rock eroded from river valleys draining the flanks of Lyttelton (n=11) and Akaroa (n=26) volcanoes and from the large embayments that penetrate the eroding Lyttelton (n=8) and Akaroa (n=25) volcanoes. We used the youngest age of the eruptions as the start of erosion (Lyttelton = 10 Ma and Akaroa = 8 Ma) to determine erosion rates. Preliminary data suggest average erosion rates of 8.2 ± 2.4 m/My (averaged over 10 Ma) on the flanks of Lyttelton Volcano and 12 ± 5.1 m/My (averaged over 8 Ma) on the flanks of Akaroa Volcano. Dating control and formation processes of Lyttelton Harbour and Akaroa Harbour are poorly constrained. The youngest lava flows, Diamond Harbor, are 5.7 Ma and flow into the Lyttelton Harbour embayment. Using endmembers of embayment age for Lyttelton Harbour (10 Ma to 5.7 Ma) the erosion rates range between 18 ± 5.8 m/My and 31 ± 10 m/My. Similarly, the hillslopes of Akaroa Harbour have slow erosion rates (based on endmember ages of 8 Ma and 5.7 Ma) and range between 22 ± 18 and 31 ± 25 m/My. Even the fastest erosion rates on Banks Peninsula are an order of magnitude slower than the erosion rates of other basalt volcanoes in the world's oceans. Using a similar methodology, Tahiti is eroding between 1200 and 2700 m/Ma (Hildenbrand et al., 2008). Other erosion rates, based on sediment yields and water chemistry for La Reunion (400 to 3000 m/Ma; Louvat and Allegre, 1997), Guadeloupe (400 to 1700 m/Ma; Ricci et al., 2014), and Martinique (800 m/Ma; Germa et al., 2010) are also significantly faster than erosion rates of Banks Peninsula.

Multimodal hard x-ray nanoprobe facility by nested Montel mirrors aimed for 40nm resolution at Taiwan Photon Source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yin, Gung-Chian, E-mail: gcyin@nsrrc.org.tw; Chang, Shi-Hung; Chen, Bo-Yi

2016-01-28

The hard X-ray nanoprobe facility at Taiwan Photon Source (TPS) provides multimodal X-ray detections, including XRF, XAS, XEOL, projection microscope, CDI, etc. Resulting from the large numerical aperture obtained by utilizing nested Montel mirrors, the beamline with a moderate length 75 meters can conduct similar performance with those beamlines longer than 100 meters. The mirrors are symmetrically placed with a 45 degrees cut. The beamline optics is thus designed to take the advantage of the symmetry of mirrors such that a round focal spot is accomplished. The size and the divergence of the focus spot are simulated around 40 nm andmore » 6.29 mrad, respectively. The whole facility including the beamline and the stations will be operated under vacuum to preserve the photon coherence as well as to prevent the system from unnecessary environmental interference. A SEM in close cooperation with laser interferometers is equipped to precisely locate the position of the sample. This endstation is scheduled to be commissioned in the fall of 2016.« less

Tunable-Range, Photon-Mediated Atomic Interactions in Multimode Cavity QED

NASA Astrophysics Data System (ADS)

Vaidya, Varun D.; Guo, Yudan; Kroeze, Ronen M.; Ballantine, Kyle E.; Kollár, Alicia J.; Keeling, Jonathan; Lev, Benjamin L.

2018-01-01

Optical cavity QED provides a platform with which to explore quantum many-body physics in driven-dissipative systems. Single-mode cavities provide strong, infinite-range photon-mediated interactions among intracavity atoms. However, these global all-to-all couplings are limiting from the perspective of exploring quantum many-body physics beyond the mean-field approximation. The present work demonstrates that local couplings can be created using multimode cavity QED. This is established through measurements of the threshold of a superradiant, self-organization phase transition versus atomic position. Specifically, we experimentally show that the interference of near-degenerate cavity modes leads to both a strong and tunable-range interaction between Bose-Einstein condensates (BECs) trapped within the cavity. We exploit the symmetry of a confocal cavity to measure the interaction between real BECs and their virtual images without unwanted contributions arising from the merger of real BECs. Atom-atom coupling may be tuned from short range to long range. This capability paves the way toward future explorations of exotic, strongly correlated systems such as quantum liquid crystals and driven-dissipative spin glasses.

Multimodal computational microscopy based on transport of intensity equation

NASA Astrophysics Data System (ADS)

Li, Jiaji; Chen, Qian; Sun, Jiasong; Zhang, Jialin; Zuo, Chao

2016-12-01

Transport of intensity equation (TIE) is a powerful tool for phase retrieval and quantitative phase imaging, which requires intensity measurements only at axially closely spaced planes without a separate reference beam. It does not require coherent illumination and works well on conventional bright-field microscopes. The quantitative phase reconstructed by TIE gives valuable information that has been encoded in the complex wave field by passage through a sample of interest. Such information may provide tremendous flexibility to emulate various microscopy modalities computationally without requiring specialized hardware components. We develop a requisite theory to describe such a hybrid computational multimodal imaging system, which yields quantitative phase, Zernike phase contrast, differential interference contrast, and light field moment imaging, simultaneously. It makes the various observations for biomedical samples easy. Then we give the experimental demonstration of these ideas by time-lapse imaging of live HeLa cell mitosis. Experimental results verify that a tunable lens-based TIE system, combined with the appropriate postprocessing algorithm, can achieve a variety of promising imaging modalities in parallel with the quantitative phase images for the dynamic study of cellular processes.

3D Mueller-matrix mapping of biological optically anisotropic networks

NASA Astrophysics Data System (ADS)

Ushenko, O. G.; Ushenko, V. O.; Bodnar, G. B.; Zhytaryuk, V. G.; Prydiy, O. G.; Koval, G.; Lukashevich, I.; Vanchuliak, O.

2018-01-01

The paper consists of two parts. The first part presents short theoretical basics of the method of azimuthally-invariant Mueller-matrix description of optical anisotropy of biological tissues. It was provided experimentally measured coordinate distributions of Mueller-matrix invariants (MMI) of linear and circular birefringences of skeletal muscle tissue. It was defined the values of statistic moments, which characterize the distributions of amplitudes of wavelet coefficients of MMI at different scales of scanning. The second part presents the data of statistic analysis of the distributions of amplitude of wavelet coefficients of the distributions of linear birefringence of myocardium tissue died after the infarction and ischemic heart disease. It was defined the objective criteria of differentiation of the cause of death.

Multiscale polarization diagnostics of birefringent networks in problems of necrotic changes diagnostics

NASA Astrophysics Data System (ADS)

Sakhnovskiy, M. Yu.; Ushenko, Yu. O.; Ushenko, V. O.; Besaha, R. N.; Pavlyukovich, N.; Pavlyukovich, O.

2018-01-01

The paper consists of two parts. The first part presents short theoretical basics of the method of azimuthally-invariant Mueller-matrix description of optical anisotropy of biological tissues. It was provided experimentally measured coordinate distributions of Mueller-matrix invariants (MMI) of linear and circular birefringences of skeletal muscle tissue. It was defined the values of statistic moments, which characterize the distributions of amplitudes of wavelet coefficients of MMI at different scales of scanning. The second part presents the data of statistic analysis of the distributions of amplitude of wavelet coefficients of the distributions of linear birefringence of myocardium tissue died after the infarction and ischemic heart disease. It was defined the objective criteria of differentiation of the cause of death.

Wavelet analysis of birefringence images of myocardium tissue

NASA Astrophysics Data System (ADS)

Sakhnovskiy, M. Yu.; Ushenko, Yu. O.; Kushnerik, L.; Soltys, I. V.; Pavlyukovich, N.; Pavlyukovich, O.

2018-01-01

The paper consists of two parts. The first part presents short theoretical basics of the method of azimuthally-invariant Mueller-matrix description of optical anisotropy of biological tissues. It was provided experimentally measured coordinate distributions of Mueller-matrix invariants (MMI) of linear and circular birefringences of skeletal muscle tissue. It was defined the values of statistic moments, which characterize the distributions of amplitudes of wavelet coefficients of MMI at different scales of scanning. The second part presents the data of statistic analysis of the distributions of amplitude of wavelet coefficients of the distributions of linear birefringence of myocardium tissue died after the infarction and ischemic heart disease. It was defined the objective criteria of differentiation of the cause of death.

Climate-change-driven accelerated sea-level rise detected in the altimeter era.

PubMed

Nerem, R S; Beckley, B D; Fasullo, J T; Hamlington, B D; Masters, D; Mitchum, G T

2018-02-27

Using a 25-y time series of precision satellite altimeter data from TOPEX/Poseidon, Jason-1, Jason-2, and Jason-3, we estimate the climate-change-driven acceleration of global mean sea level over the last 25 y to be 0.084 ± 0.025 mm/y 2 Coupled with the average climate-change-driven rate of sea level rise over these same 25 y of 2.9 mm/y, simple extrapolation of the quadratic implies global mean sea level could rise 65 ± 12 cm by 2100 compared with 2005, roughly in agreement with the Intergovernmental Panel on Climate Change (IPCC) 5th Assessment Report (AR5) model projections. Copyright © 2018 the Author(s). Published by PNAS.

Multimodal assessment of visual attention using the Bethesda Eye & Attention Measure (BEAM).

PubMed

Ettenhofer, Mark L; Hershaw, Jamie N; Barry, David M

2016-01-01

Computerized cognitive tests measuring manual response time (RT) and errors are often used in the assessment of visual attention. Evidence suggests that saccadic RT and errors may also provide valuable information about attention. This study was conducted to examine a novel approach to multimodal assessment of visual attention incorporating concurrent measurements of saccadic eye movements and manual responses. A computerized cognitive task, the Bethesda Eye & Attention Measure (BEAM) v.34, was designed to evaluate key attention networks through concurrent measurement of saccadic and manual RT and inhibition errors. Results from a community sample of n = 54 adults were analyzed to examine effects of BEAM attention cues on manual and saccadic RT and inhibition errors, internal reliability of BEAM metrics, relationships between parallel saccadic and manual metrics, and relationships of BEAM metrics to demographic characteristics. Effects of BEAM attention cues (alerting, orienting, interference, gap, and no-go signals) were consistent with previous literature examining key attention processes. However, corresponding saccadic and manual measurements were weakly related to each other, and only manual measurements were related to estimated verbal intelligence or years of education. This study provides preliminary support for the feasibility of multimodal assessment of visual attention using the BEAM. Results suggest that BEAM saccadic and manual metrics provide divergent measurements. Additional research will be needed to obtain comprehensive normative data, to cross-validate BEAM measurements with other indicators of neural and cognitive function, and to evaluate the utility of these metrics within clinical populations of interest.

A highly stable and switchable dual-wavelength laser using coupled microfiber Mach-Zehnder interferometer as an optical filter

NASA Astrophysics Data System (ADS)

Jasim, A. A.; Ahmad, H.

2017-12-01

The generation and switching of dual-wavelength laser based on compact coupled microfiber Mach-Zehnder interferometer (CM-MZI) is reported. The CM-MZI is constructed by overlapping two portions of a single tapered optical fiber which has a diameter of 9 μm as to create multi-mode interference and also to produce spatial mode beating as to suppress mode competition in the homogeneous gain medium. The system is able to generate a dual-wavelength laser output that can be switched with the aid of the polarization rotation technique. Four dual-wavelength oscillation pairs are obtained from the interference fringe peaks of the CM-MZI comb filter with a switched channel spacing of 1.5 nm, 3.0 nm, and 6.0 nm. The wavelength spacing is stable at different pump powers. The lasing wavelength has a 3-dB linewidth of about 30 pm and peak-to-floor ration of about 55 dB at a pump power of 38 mW.

Sharing Human-Generated Observations by Integrating HMI and the Semantic Sensor Web

PubMed Central

Sigüenza, Álvaro; Díaz-Pardo, David; Bernat, Jesús; Vancea, Vasile; Blanco, José Luis; Conejero, David; Gómez, Luis Hernández

2012-01-01

Current “Internet of Things” concepts point to a future where connected objects gather meaningful information about their environment and share it with other objects and people. In particular, objects embedding Human Machine Interaction (HMI), such as mobile devices and, increasingly, connected vehicles, home appliances, urban interactive infrastructures, etc., may not only be conceived as sources of sensor information, but, through interaction with their users, they can also produce highly valuable context-aware human-generated observations. We believe that the great promise offered by combining and sharing all of the different sources of information available can be realized through the integration of HMI and Semantic Sensor Web technologies. This paper presents a technological framework that harmonizes two of the most influential HMI and Sensor Web initiatives: the W3C's Multimodal Architecture and Interfaces (MMI) and the Open Geospatial Consortium (OGC) Sensor Web Enablement (SWE) with its semantic extension, respectively. Although the proposed framework is general enough to be applied in a variety of connected objects integrating HMI, a particular development is presented for a connected car scenario where drivers' observations about the traffic or their environment are shared across the Semantic Sensor Web. For implementation and evaluation purposes an on-board OSGi (Open Services Gateway Initiative) architecture was built, integrating several available HMI, Sensor Web and Semantic Web technologies. A technical performance test and a conceptual validation of the scenario with potential users are reported, with results suggesting the approach is sound. PMID:22778643

Sharing human-generated observations by integrating HMI and the Semantic Sensor Web.

PubMed

Sigüenza, Alvaro; Díaz-Pardo, David; Bernat, Jesús; Vancea, Vasile; Blanco, José Luis; Conejero, David; Gómez, Luis Hernández

2012-01-01

Current "Internet of Things" concepts point to a future where connected objects gather meaningful information about their environment and share it with other objects and people. In particular, objects embedding Human Machine Interaction (HMI), such as mobile devices and, increasingly, connected vehicles, home appliances, urban interactive infrastructures, etc., may not only be conceived as sources of sensor information, but, through interaction with their users, they can also produce highly valuable context-aware human-generated observations. We believe that the great promise offered by combining and sharing all of the different sources of information available can be realized through the integration of HMI and Semantic Sensor Web technologies. This paper presents a technological framework that harmonizes two of the most influential HMI and Sensor Web initiatives: the W3C's Multimodal Architecture and Interfaces (MMI) and the Open Geospatial Consortium (OGC) Sensor Web Enablement (SWE) with its semantic extension, respectively. Although the proposed framework is general enough to be applied in a variety of connected objects integrating HMI, a particular development is presented for a connected car scenario where drivers' observations about the traffic or their environment are shared across the Semantic Sensor Web. For implementation and evaluation purposes an on-board OSGi (Open Services Gateway Initiative) architecture was built, integrating several available HMI, Sensor Web and Semantic Web technologies. A technical performance test and a conceptual validation of the scenario with potential users are reported, with results suggesting the approach is sound.

Antithyroid Drug Use in Pregnancy and Birth Defects: Why Some Studies Find Clear Associations, and Some Studies Report None.

PubMed

Laurberg, Peter; Andersen, Stine Linding

2015-11-01

Rare cases of birth defects after the use of methimazole (MMI) or carbimazole to treat hyperthyroidism in early pregnancy have been reported since 1972, whereas propylthiouracil (PTU) has not been considered teratogenic. Recently, two studies reported birth defects after the use of MMI in early pregnancy to affect 2-4% of exposed children, and one study also found birth defects after the use of PTU. On the other hand, some published studies did not find associations between the use of thionamides and birth defects. The methods used in the two positive and the four negative reports are reviewed. The two positive studies included a sufficient number of children exposed to MMI (n = 1231 and 1097) to evaluate the studied outcomes, whereas the four negative studies included a much lower number of exposed children (n = 73, 108, 30, and 124). Considering PTU, the birth defects observed in one study were in general milder and tended to be diagnosed and registered only when they resulted in complications and led to surgery after one year of age. None of the negative studies has investigated outcomes after one year of age. Studies finding no associations between early pregnancy exposure to antithyroid drugs and birth defects were either not sufficiently powered or did not study outcomes at optimal ages.

Pharmacokinetics-on-a-Chip Using Label-Free SERS Technique for Programmable Dual-Drug Analysis.

PubMed

Fei, Jiayuan; Wu, Lei; Zhang, Yizhi; Zong, Shenfei; Wang, Zhuyuan; Cui, Yiping

2017-06-23

Synergistic effects of dual or multiple drugs have attracted great attention in medical fields, especially in cancer therapies. We provide a programmable microfluidic platform for pharmacokinetic detection of multiple drugs in multiple cells. The well-designed microfluidic platform includes two 2 × 3 microarrays of cell chambers, two gradient generators, and several pneumatic valves. Through the combined use of valves and gradient generators, each chamber can be controlled to infuse different kinds of living cells and drugs with specific concentrations as needed. In our experiments, 6-mercaptopurine (6MP) and methimazole (MMI) were chosen as two drug models and their pharmacokinetic parameters in different living cells were monitored through intracellular SERS spectra, which reflected the molecular structure of these drugs. The dynamic change of SERS fingerprints from 6MP and MMI molecules were recorded during drug metabolism in living cells. The results indicated that both 6MP and MMI molecules were diffused into the cells within 4 min and excreted out after 36 h. Moreover, the intracellular distribution of these drugs was monitored through SERS mapping. Thus, our microfluidic platform simultaneously accomplishes the functions to monitor pharmacokinetic action, distribution, and fingerprint of multiple drugs in multiple cells. Owing to its real-time, rapid-speed, high-precision, and programmable capability of multiple-drug and multicell analysis, such a microfluidic platform has great potential in drug design and development.

Fast Computation of Ground Motion Shaking Map base on the Modified Stochastic Finite Fault Modeling

NASA Astrophysics Data System (ADS)

Shen, W.; Zhong, Q.; Shi, B.

2012-12-01

Rapidly regional MMI mapping soon after a moderate-large earthquake is crucial to loss estimation, emergency services and planning of emergency action by the government. In fact, many countries show different degrees of attention on the technology of rapid estimation of MMI , and this technology has made significant progress in earthquake-prone countries. In recent years, numerical modeling of strong ground motion has been well developed with the advances of computation technology and earthquake science. The computational simulation of strong ground motion caused by earthquake faulting has become an efficient way to estimate the regional MMI distribution soon after earthquake. In China, due to the lack of strong motion observation in network sparse or even completely missing areas, the development of strong ground motion simulation method has become an important means of quantitative estimation of strong motion intensity. In many of the simulation models, stochastic finite fault model is preferred to rapid MMI estimating for its time-effectiveness and accuracy. In finite fault model, a large fault is divided into N subfaults, and each subfault is considered as a small point source. The ground motions contributed by each subfault are calculated by the stochastic point source method which is developed by Boore, and then summed at the observation point to obtain the ground motion from the entire fault with a proper time delay. Further, Motazedian and Atkinson proposed the concept of Dynamic Corner Frequency, with the new approach, the total radiated energy from the fault and the total seismic moment are conserved independent of subfault size over a wide range of subfault sizes. In current study, the program EXSIM developed by Motazedian and Atkinson has been modified for local or regional computations of strong motion parameters such as PGA, PGV and PGD, which are essential for MMI estimating. To make the results more reasonable, we consider the impact of V30 for the ground shaking intensity, and the results of the comparisons between the simulated and observed MMI for the 2004 Mw 6.0 Parkfield earthquake, the 2008 Mw 7.9Wenchuan earthquake and the 1976 Mw 7.6Tangshan earthquake is fairly well. Take Parkfield earthquake as example, the simulative result reflect the directivity effect and the influence of the shallow velocity structure well. On the other hand, the simulative data is in good agreement with the network data and NGA (Next Generation Attenuation). The consumed time depends on the number of the subfaults and the number of the grid point. For the 2004 Mw 6.0 Parkfield earthquake, the grid size we calculated is 2.5° × 2.5°, the grid space is 0.025°, and the total time consumed is about 1.3hours. For the 2008 Mw 7.9 Wenchuan earthquake, the grid size calculated is 10° × 10°, the grid space is 0.05°, the total number of grid point is more than 40,000, and the total time consumed is about 7.5 hours. For t the 1976 Mw 7.6 Tangshan earthquake, the grid size we calculated is 4° × 6°, the grid space is 0.05°, and the total time consumed is about 2.1 hours. The CPU we used is 3.40GHz, and such computational time could further reduce by using GPU computing technique and other parallel computing technique. This is also our next focus.

Serial recall of visuospatial and verbal information with and without material-specific interference: implications for contemporary models of working memory.

PubMed

Davis, Lynne C; Rane, Shruti; Hiscock, Merrill

2013-01-01

A longstanding question in working memory (WM) research concerns the fractionation of verbal and nonverbal processing. Although some contemporary models include both domain-specific and general-purpose mechanisms, the necessity to postulate differential processing of verbal and nonverbal material remains unclear. In the present two-experiment series we revisit the order reconstruction paradigm that Jones, Farrand, Stuart, and Morris (1995) used to support a unitary model of WM. Goals were to assess (1) whether serial position curves for dot positions differ from curves for letter names; and (2) whether selective interference can be demonstrated. Although we replicated Jones et al.'s finding of similar serial position curves for the two tasks, this similarity could reflect the demands of the order reconstruction paradigm rather than undifferentiated processing of verbal and nonverbal stimuli. Both generalised and material-specific interference was found, which can be attributed to competition between primary and secondary tasks for attentional resources. As performance levels for the combined primary and secondary tasks exceed active WM capacity limits, primary task items apparently are removed from active memory during processing of the secondary list and held temporarily in maintenance storage. We conclude that active WM is multimodal but maintenance stores may be domain specific.

Near-field optical technique applied for investigation of the characteristics of polymer fiber and waveguide structures.

PubMed

Ming, Hai; Tang, Lin; Sun, Xiaohong; Zhang, Jiangying; Wang, Pei; Lu, Yonghua; Bai, Ming; Guo, Yang; Xie, Aifang; Zhang, Zebo

2004-01-01

This article summarizes the near-field optical technique applied for investigating the characteristics of polymer fiber and waveguide structures. The near-field optical technique is used to analyze multimode interference structures of fiber. The localized fluctuation of the transmission caused by fractal cluster is carried out in Nd3+- and Eu3+-doped polymer fiber and film by means of a scanning near-field optical microscopy. The near-field optical spectrum of Nd3+-doped polymer fiber is investigated. The topography and near-field intensity images of Azo-polymer liquid crystal film for waveguide are obtained simultaneously.

Temperature-dependent transitions between normal and inverse isotope effects pertaining to the interaction of H-H and C-H bonds with transition metal centers.

PubMed

Parkin, Gerard

2009-02-17

Deuterium kinetic isotope effects (KIEs) serve as versatile tools to infer details about reaction mechanisms and the nature of transition states, while equilibrium isotope effects (EIEs) associated with the site preferences of hydrogen and deuterium enable researchers to study aspects of molecular structure. Researchers typically interpret primary deuterium isotope effects based on two simple guidelines: (i) the KIE for an elementary reaction is normal (k(H)/k(D) > 1) and (ii) the EIE is dictated by deuterium preferring to be located in the site corresponding to the highest frequency oscillator. In this Account, we evaluate the applicability of these rules to the interactions of H-H and C-H bonds with a transition metal center. Significantly, experimental and computational studies question the predictability of primary EIEs in these systems based on the notion that deuterium prefers to occupy the highest frequency oscillator. In particular, the EIEs for (i) formation of sigma-complexes by coordination of H-H and C-H bonds and (ii) oxidative addition of dihydrogen exhibit unusual temperature dependencies, such that the same system may demonstrate both normal (i.e., K(H)/K(D) > 1) and inverse (i.e., K(H)/K(D) < 1) values. The transition between a normal and inverse EIE indicates that these systems do not demonstrate the typical monotonic variation predicted by the van't Hoff relationship. Instead, the calculated EIEs in these systems are 0 at 0 K, increase to a value greater than 1, and then decrease to unity at infinite temperature. This unusual behavior may be rationalized by considering the individual factors that contribute to the EIE. Specifically, the EIE may be expressed in the form EIE = SYM x MMI x EXC x ZPE (where SYM is the symmetry factor, MMI is the mass-moment of inertia term, EXC is the excitation term, and ZPE is the zero-point energy term), and the distinctive temperature profile results from the inverse ZPE (enthalpy) and normal [SYM x MMI x EXC] (entropy) components opposing each other and having different temperature dependencies. At low temperatures, the ZPE component dominates and the EIE is inverse, while at high temperatures, the [SYM x MMI x EXC] component dominates and the EIE is normal. The inverse nature of the ZPE term is a consequence of the rotational and translational degrees of freedom of RH (R = H, CH(3)) becoming low-energy isotopically sensitive vibrations in the product, while the normal nature of the [SYM x MMI x EXC] component results from deuterium substitution having a larger impact on the moment of inertia of the smaller molecule.

An Intelligent Man-Machine Interface—Multi-Robot Control Adapted for Task Engagement Based on Single-Trial Detectability of P300

PubMed Central

Kirchner, Elsa A.; Kim, Su K.; Tabie, Marc; Wöhrle, Hendrik; Maurus, Michael; Kirchner, Frank

2016-01-01

Advanced man-machine interfaces (MMIs) are being developed for teleoperating robots at remote and hardly accessible places. Such MMIs make use of a virtual environment and can therefore make the operator immerse him-/herself into the environment of the robot. In this paper, we present our developed MMI for multi-robot control. Our MMI can adapt to changes in task load and task engagement online. Applying our approach of embedded Brain Reading we improve user support and efficiency of interaction. The level of task engagement was inferred from the single-trial detectability of P300-related brain activity that was naturally evoked during interaction. With our approach no secondary task is needed to measure task load. It is based on research results on the single-stimulus paradigm, distribution of brain resources and its effect on the P300 event-related component. It further considers effects of the modulation caused by a delayed reaction time on the P300 component evoked by complex responses to task-relevant messages. We prove our concept using single-trial based machine learning analysis, analysis of averaged event-related potentials and behavioral analysis. As main results we show (1) a significant improvement of runtime needed to perform the interaction tasks compared to a setting in which all subjects could easily perform the tasks. We show that (2) the single-trial detectability of the event-related potential P300 can be used to measure the changes in task load and task engagement during complex interaction while also being sensitive to the level of experience of the operator and (3) can be used to adapt the MMI individually to the different needs of users without increasing total workload. Our online adaptation of the proposed MMI is based on a continuous supervision of the operator's cognitive resources by means of embedded Brain Reading. Operators with different qualifications or capabilities receive only as many tasks as they can perform to avoid mental overload as well as mental underload. PMID:27445742

Semantic Integration for Marine Science Interoperability Using Web Technologies

NASA Astrophysics Data System (ADS)

Rueda, C.; Bermudez, L.; Graybeal, J.; Isenor, A. W.

2008-12-01

The Marine Metadata Interoperability Project, MMI (http://marinemetadata.org) promotes the exchange, integration, and use of marine data through enhanced data publishing, discovery, documentation, and accessibility. A key effort is the definition of an Architectural Framework and Operational Concept for Semantic Interoperability (http://marinemetadata.org/sfc), which is complemented with the development of tools that realize critical use cases in semantic interoperability. In this presentation, we describe a set of such Semantic Web tools that allow performing important interoperability tasks, ranging from the creation of controlled vocabularies and the mapping of terms across multiple ontologies, to the online registration, storage, and search services needed to work with the ontologies (http://mmisw.org). This set of services uses Web standards and technologies, including Resource Description Framework (RDF), Web Ontology language (OWL), Web services, and toolkits for Rich Internet Application development. We will describe the following components: MMI Ontology Registry: The MMI Ontology Registry and Repository provides registry and storage services for ontologies. Entries in the registry are associated with projects defined by the registered users. Also, sophisticated search functions, for example according to metadata items and vocabulary terms, are provided. Client applications can submit search requests using the WC3 SPARQL Query Language for RDF. Voc2RDF: This component converts an ASCII comma-delimited set of terms and definitions into an RDF file. Voc2RDF facilitates the creation of controlled vocabularies by using a simple form-based user interface. Created vocabularies and their descriptive metadata can be submitted to the MMI Ontology Registry for versioning and community access. VINE: The Vocabulary Integration Environment component allows the user to map vocabulary terms across multiple ontologies. Various relationships can be established, for example exactMatch, narrowerThan, and subClassOf. VINE can compute inferred mappings based on the given associations. Attributes about each mapping, like comments and a confidence level, can also be included. VINE also supports registering and storing resulting mapping files in the Ontology Registry. The presentation will describe the application of semantic technologies in general, and our planned applications in particular, to solve data management problems in the marine and environmental sciences.

New shielding configurations for a simultaneous PET/MRI scanner at 7T

PubMed Central

Peng, Bo J.; Wu, Yibao; Cherry, Simon R.; Walton, Jeffrey H.

2014-01-01

Understanding sources of electromagnetic interference are important in designing any electronic system. This is especially true when combining positron emission tomography (PET) and magnetic resonance imaging (MRI) in a multimodality system as coupling between the subsystems can degrade the performance of either modality. For this reason, eliminating radio frequency (RF) interference and gradient-induced eddy currents have been major challenges in building simultaneous hybrid PET/MRI systems. MRI requires negligible RF interference at the Larmor resonance frequency, while RF interference at almost any frequency may corrupt PET data. Moreover, any scheme that minimizes these interactions would, ideally, not compromise the performance of either subsystem. This paper lays out a plan to resolve these problems. A carbon fiber composite material is found to be a good RF shield at the Larmor frequency (300 MHz in this work) while introducing negligible gradient eddy currents. This carbon fiber composite also provides excellent structural support for the PET detector components. Low frequency electromagnetic radiation (81 kHz here) from the switching power supplies of the gradient amplifiers was also found to interfere with the PET detector. Placing the PET detector module between two carbon fiber tubes and grounding the inner carbon fiber tube to the PET detector module ground reduced this interference. Further reductions were achieved by adding thin copper (Cu) foil on the outer carbon fiber case and electrically grounding the PET detector module so that all 3 components had a common ground, i.e. with the PET detector in an electrostatic cage. Finally, gradient switching typical in MRI sequences can result in count losses in the particular PET detector design studied. Moreover, the magnitude of this effect depends on the location of the detector within the magnet bore and which MRI gradient is being switched. These findings have a bearing on future designs of PET/MRI systems. PMID:24380812

New Families of Skewed Higher-Order Kernel Estimators to Solve the BSS/ICA Problem for Multimodal Sources Mixtures.

PubMed

Jabbar, Ahmed Najah

2018-04-13

This letter suggests two new types of asymmetrical higher-order kernels (HOK) that are generated using the orthogonal polynomials Laguerre (positive or right skew) and Bessel (negative or left skew). These skewed HOK are implemented in the blind source separation/independent component analysis (BSS/ICA) algorithm. The tests for these proposed HOK are accomplished using three scenarios to simulate a real environment using actual sound sources, an environment of mixtures of multimodal fast-changing probability density function (pdf) sources that represent a challenge to the symmetrical HOK, and an environment of an adverse case (near gaussian). The separation is performed by minimizing the mutual information (MI) among the mixed sources. The performance of the skewed kernels is compared to the performance of the standard kernels such as Epanechnikov, bisquare, trisquare, and gaussian and the performance of the symmetrical HOK generated using the polynomials Chebyshev1, Chebyshev2, Gegenbauer, Jacobi, and Legendre to the tenth order. The gaussian HOK are generated using the Hermite polynomial and the Wand and Schucany procedure. The comparison among the 96 kernels is based on the average intersymbol interference ratio (AISIR) and the time needed to complete the separation. In terms of AISIR, the skewed kernels' performance is better than that of the standard kernels and rivals most of the symmetrical kernels' performance. The importance of these new skewed HOK is manifested in the environment of the multimodal pdf mixtures. In such an environment, the skewed HOK come in first place compared with the symmetrical HOK. These new families can substitute for symmetrical HOKs in such applications.

Integrated femtosecond stimulated Raman scattering and two-photon fluorescence imaging of subcellular lipid and vesicular structures

NASA Astrophysics Data System (ADS)

Li, Xuesong; Lam, Wen Jiun; Cao, Zhe; Hao, Yan; Sun, Qiqi; He, Sicong; Mak, Ho Yi; Qu, Jianan Y.

2015-11-01

The primary goal of this study is to demonstrate that stimulated Raman scattering (SRS) as a new imaging modality can be integrated into a femtosecond (fs) nonlinear optical (NLO) microscope system. The fs sources of high pulse peak power are routinely used in multimodal nonlinear microscopy to enable efficient excitation of multiple NLO signals. However, with fs excitations, the SRS imaging of subcellular lipid and vesicular structures encounters significant interference from proteins due to poor spectral resolution and a lack of chemical specificity, respectively. We developed a unique NLO microscope of fs excitation that enables rapid acquisition of SRS and multiple two-photon excited fluorescence (TPEF) signals. In the in vivo imaging of transgenic C. elegans animals, we discovered that by cross-filtering false positive lipid signals based on the TPEF signals from tryptophan-bearing endogenous proteins and lysosome-related organelles, the imaging system produced highly accurate assignment of SRS signals to lipid. Furthermore, we demonstrated that the multimodal NLO microscope system could sequentially image lipid structure/content and organelles, such as mitochondria, lysosomes, and the endoplasmic reticulum, which are intricately linked to lipid metabolism.

“RaMassays”: Synergistic Enhancement of Plasmon-Free Raman Scattering and Mass Spectrometry for Multimodal Analysis of Small Molecules

NASA Astrophysics Data System (ADS)

Alessandri, Ivano; Vassalini, Irene; Bertuzzi, Michela; Bontempi, Nicolò; Memo, Maurizio; Gianoncelli, Alessandra

2016-10-01

SiO2/TiO2 core/shell (T-rex) beads were exploited as “all-in-one” building-block materials to create analytical assays that combine plasmon-free surface enhanced Raman scattering (SERS) and surface assisted laser desorption/ionization (SALDI) mass spectrometry (RaMassays). Such a multi-modal approach relies on the unique optical properties of T-rex beads, which are able to harvest and manage light in both UV and Vis range, making ionization and Raman scattering more efficient. RaMassays were successfully applied to the detection of small (molecular weight, M.W. <400 Da) molecules with a key relevance in biochemistry and pharmaceutical analysis. Caffeine and cocaine were utilized as molecular probes to test the combined SERS/SALDI response of RaMassays, showing excellent sensitivity and reproducibility. The differentiation between amphetamine/ephedrine and theophylline/theobromine couples demonstrated the synergistic reciprocal reinforcement of SERS and SALDI. Finally, the conversion of L-tyrosine in L-DOPA was utilized to probe RaMassays as analytical tools for characterizing reaction intermediates without introducing any spurious effects. RaMassays exhibit important advantages over plasmonic nanoparticles in terms of reproducibility, absence of interference and potential integration in multiplexed devices.

Exacerbated liver injury of antithyroid drugs in endotoxin-treated mice.

PubMed

Heidari, Reza; Ahmadi, Fatemeh; Rahimi, Hamid Reza; Azarpira, Negar; Hosseinzadeh, Massood; Najibi, Asma; Niknahad, Hossein

2018-05-03

Drug-induced liver injury is a major concern in clinical studies as well as in post-marketing surveillance. Previous evidence suggested that drug exposure during periods of inflammation could increase an individual's susceptibility to drug hepatoxicity. The antithyroid drugs, methimazole (MMI) and propylthiouracil (PTU) can cause adverse reactions in patients, with liver as a usual target. We tested the hypothesis that MMI and PTU could be rendered hepatotoxic in animals undergoing a modest inflammation. Mice were treated with a nonhepatotoxic dose of LPS (100 µg/kg, i.p) or its vehicle. Nonhepatotoxic doses of MMI (10, 25 and 50 mg/kg, oral) and PTU (10, 25 and 50 mg/kg, oral) were administered two hours after LPS treatment. It was found that liver injury was evident only in animals received both drug and LPS, as estimated by increases in serum alanine aminotransferase (ALT), lactate dehydrogenase (LDH), aspartate aminotransferase (AST), and TNF-α. An increase in liver myeloperoxidase (MPO) enzyme activity and tissue lipid peroxidation (LPO) in addition of liver glutathione (GSH) depletion were also detected in LPS and antithyroid drugs cotreated animals. Furthermore, histopathological changes including, endotheliitis, fatty changes, severe inflammatory cells infiltration (hepatitis) and sinusoidal congestion were detected in liver tissue. Methyl palmitate (2 g/kg, i.v, 44 hours before LPS), as a macrophage suppressor, significantly alleviated antithyroids hepatotoxicity in LPS-treated animals. The results indicate a synergistic liver injury from antithyroid drugs and bacterial lipopolysaccharide coexposure.

Validating a multiple mini-interview question bank assessing entry-level reasoning skills in candidates for graduate-entry medicine and dentistry programmes.

PubMed

Roberts, Chris; Zoanetti, Nathan; Rothnie, Imogene

2009-04-01

The multiple mini-interview (MMI) was initially designed to test non-cognitive characteristics related to professionalism in entry-level students. However, it may be testing cognitive reasoning skills. Candidates to medical and dental schools come from diverse backgrounds and it is important for the validity and fairness of the MMI that these background factors do not impact on their scores. A suite of advanced psychometric techniques drawn from item response theory (IRT) was used to validate an MMI question bank in order to establish the conceptual equivalence of the questions. Bias against candidate subgroups of equal ability was investigated using differential item functioning (DIF) analysis. All 39 questions had a good fit to the IRT model. Of the 195 checklist items, none were found to have significant DIF after visual inspection of expected score curves, consideration of the number of applicants per category, and evaluation of the magnitude of the DIF parameter estimates. The question bank contains items that have been studied carefully in terms of model fit and DIF. Questions appear to measure a cognitive unidimensional construct, 'entry-level reasoning skills in professionalism', as suggested by goodness-of-fit statistics. The lack of items exhibiting DIF is encouraging in a contemporary high-stakes admission setting where candidates of diverse personal, cultural and academic backgrounds are assessed by common means. This IRT approach has potential to provide assessment designers with a quality control procedure that extends to the level of checklist items.

Outcome of radioiodine-131 therapy in hyperfunctioning thyroid nodules: a 20 years' retrospective study.

PubMed

Ceccarelli, Claudia; Bencivelli, Walter; Vitti, Paolo; Grasso, Lucia; Pinchera, Aldo

2005-03-01

To investigate the risk of hypothyroidism after radioiodine (131I) treatment for hyperfunctioning thyroid nodules. Retrospective analysis of patients treated with 131I for hyperfunctioning thyroid nodules and followed up for a maximum of 20 years. A total of 346 patients treated with 131I in the years 1975-95, for a single hyperfunctioning nodule. Hypothyroidism was defined as TSH levels > 3.7 mU/l. Kaplan-Meier survival analysis was used to analyse permanence of euthyroidism after 131I. A stepwise Cox proportional hazard model was used to identify factors influencing the progression to hypothyroidism. The cumulative incidence of hypothyroidism was 7.6% at 1 year, 28% at 5 years, 46% at 10 years and 60% at 20 years. Age (P < 0.01), 24-th 131I uptake (P < 0.05) and previous treatment with methimazole (MMI, P < 0.1) were associated with a faster progression towards hypothyroidism, while thyroid and nodule size, thyroid status at diagnosis and degree of extranodular thyroid parenchymal suppression had no influence. In hyperthyroid patients with partial parenchymal suppression, however, previous MMI treatment was the most important prognostic factor (P < 0.01). After 20 years of follow-up, 60% of patients treated with 131I for a single hyperfunctioning nodule are hypothyroid. Factors increasing the risk of hypothyroidism are age, 131I uptake and MMI pretreatment. The prognostic value of this last factor, however, depends on the degree of suppression of the extranodular thyroid parenchyma at the scan.

Assessing the location and magnitude of the 20 October 1870 Charlevoix, Quebec, earthquake

USGS Publications Warehouse

Ebel, John E.; Dupuy, Megan; Bakun, William H.

2013-01-01

The Charlevoix, Quebec, earthquake of 20 October 1870 caused damage to several towns in Quebec and was felt throughout much of southeastern Canada and along the U.S. Atlantic seaboard from Maine to Maryland. Site‐specific damage and felt reports from Canadian and U.S. cities and towns were used in analyses of the location and magnitude of the earthquake. The macroseismic center of the earthquake was very close to Baie‐St‐Paul, where the greatest damage was reported, and the intensity magnitude MI was found to be 5.8, with a 95% probability range of 5.5–6.0. After corrections for epicentral‐distance differences are applied, the modified Mercalli intensity (MMI) data for the 1870 earthquake and for the moment magnitude M 6.2 Charlevoix earthquake of 1925 at common sites show that on average, the MMI readings are about 0.8 intensity units smaller for the 1870 earthquake than for the 1925 earthquake, suggesting that the 1870 earthquake was MI 5.7. A similar comparison of the MMI data for the 1870 earthquake with the corresponding data for the M 5.9 1988 Saguenay event suggests that the 1870 earthquake was MI 6.0. These analyses all suggest that the magnitude of the 1870 Charlevoix earthquake is between MI 5.5 and MI 6.0, with a best estimate of MI 5.8.

Displacement rates on the Toroweap and Hurricane faults: implications for Quaternary downcutting in the Grand Canyon, Arizona

USGS Publications Warehouse

Fenton, Cassandra R.; Webb, Robert H.; Pearthree, Philip A.; Cerling, Thure E.; Poreda, Robert J.

2001-01-01

The Toroweap and Hurricane faults, considered to be the most active in Arizona, cross the Uinkaret volcanic field in the western Grand Canyon. These normal faults are downthrown to the west, and the Colorado River crosses these faults as it flows west in the Grand Canyon. Cosmogenic 3He (3Hec) dates on basalt flows and related landforms are used to calculate vertical displacement rates for these faults. The two faults cross unruptured alluvial fans dated as 3 ka (Toroweap) and 8 ka (Hurricane), and 10 other landforms that range in age from 30 to 400 ka are displaced. Middle and late Quaternary displacement rates of the Toroweap and Hurricane faults are 70–180 and 70–170 m/m.y., respectively. On the basis of these rates, the combined displacement of 580 m on these faults could have occurred in the past 3 to 5 m.y. All 3Hec dates are younger than existing K- Ar dates and are consistent with new 40Ar/39Ar dates and existing thermoluminescence (TL) dates on basalt flows. These different dating techniques may be combined in an analysis of displacement rates. Downcutting rates for the Colorado River in the eastern Grand Canyon (400 m/m.y.) are at least double the downcutting rates west of the faults (70–160 m/m.y.). Faulting probably increased downcutting in the eastern Grand Canyon relative to downcutting in the western Grand Canyon during the late Quaternary.

Explicating the Conditions Under Which Multilevel Multiple Imputation Mitigates Bias Resulting from Random Coefficient-Dependent Missing Longitudinal Data.

PubMed

Gottfredson, Nisha C; Sterba, Sonya K; Jackson, Kristina M

2017-01-01

Random coefficient-dependent (RCD) missingness is a non-ignorable mechanism through which missing data can arise in longitudinal designs. RCD, for which we cannot test, is a problematic form of missingness that occurs if subject-specific random effects correlate with propensity for missingness or dropout. Particularly when covariate missingness is a problem, investigators typically handle missing longitudinal data by using single-level multiple imputation procedures implemented with long-format data, which ignores within-person dependency entirely, or implemented with wide-format (i.e., multivariate) data, which ignores some aspects of within-person dependency. When either of these standard approaches to handling missing longitudinal data is used, RCD missingness leads to parameter bias and incorrect inference. We explain why multilevel multiple imputation (MMI) should alleviate bias induced by a RCD missing data mechanism under conditions that contribute to stronger determinacy of random coefficients. We evaluate our hypothesis with a simulation study. Three design factors are considered: intraclass correlation (ICC; ranging from .25 to .75), number of waves (ranging from 4 to 8), and percent of missing data (ranging from 20 to 50%). We find that MMI greatly outperforms the single-level wide-format (multivariate) method for imputation under a RCD mechanism. For the MMI analyses, bias was most alleviated when the ICC is high, there were more waves of data, and when there was less missing data. Practical recommendations for handling longitudinal missing data are suggested.

Statistical benchmark for BosonSampling

NASA Astrophysics Data System (ADS)

Walschaers, Mattia; Kuipers, Jack; Urbina, Juan-Diego; Mayer, Klaus; Tichy, Malte Christopher; Richter, Klaus; Buchleitner, Andreas

2016-03-01

Boson samplers—set-ups that generate complex many-particle output states through the transmission of elementary many-particle input states across a multitude of mutually coupled modes—promise the efficient quantum simulation of a classically intractable computational task, and challenge the extended Church-Turing thesis, one of the fundamental dogmas of computer science. However, as in all experimental quantum simulations of truly complex systems, one crucial problem remains: how to certify that a given experimental measurement record unambiguously results from enforcing the claimed dynamics, on bosons, fermions or distinguishable particles? Here we offer a statistical solution to the certification problem, identifying an unambiguous statistical signature of many-body quantum interference upon transmission across a multimode, random scattering device. We show that statistical analysis of only partial information on the output state allows to characterise the imparted dynamics through particle type-specific features of the emerging interference patterns. The relevant statistical quantifiers are classically computable, define a falsifiable benchmark for BosonSampling, and reveal distinctive features of many-particle quantum dynamics, which go much beyond mere bunching or anti-bunching effects.

A wavelength-tunable fiber laser using a novel filter based on a compound interference effect

NASA Astrophysics Data System (ADS)

Zou, Hui; Lou, Shuqin; Su, Wei; Han, Bolin; Shen, Xiao

2015-01-01

A wavelength-tunable erbium-doped fiber laser is proposed and experimentally demonstrated by using a novel filter which is formed from a 2  ×  2 3 dB multimode coupler incorporating a segment of polarization maintaining fiber (PMF). By using the filter with 2.1 m lengths of PMF in a ring fiber laser, a stable single wavelength lasing is obtained experimentally. Its 3 dB bandwidth is less than 0.0147 nm and the side mode suppression ratio (SMSR) is higher than 58.91 dB. Experimental results demonstrate that mode competition can be effectively suppressed and the SMSR can be improved due to the compound interference effect aroused by the novel filter. Meanwhile the stability of the output lasing can be enhanced. By appropriately adjusting the polarization controllers (PCs), the output lasing wavelength can be tuned from 1563.51 to 1568.21 nm. This fiber laser has the advantage of a simple structure and stable operation at room temperature.

Polymer waveguide based hybrid opto-electric integration technology

NASA Astrophysics Data System (ADS)

Mao, Jinbin; Deng, Lingling; Jiang, Xiyan; Ren, Rong; Zhai, Yumeng; Wang, Jin

2014-10-01

While monolithic integration especially based on InP appears to be quite an expensive solution for optical devices, hybrid integration solutions using cheaper material platforms are considered powerful competitors because of the high freedom of design, yield optimization and relative cost-efficiency. Among them, the polymer planar-lightwave circuit (PLC) technology is regarded attractive as polymer offers the potential of fairly simple and low-cost fabrication, and of low-cost packaging. In our work, polymer PLC was fabricated by using the standard reactive ion etching (RIE) technique, while other active and passive devices can be integrated on the polymer PLC platform. Exemplary polymer waveguide devices was a 13-channel arrayed waveguide grating (AWG) chip, where the central channel cross-talk was below -30dB and the polarization dependent frequency shift was mitigated by inserting a half wave plate. An optical 900 hybrid was also realized with one 2×4 multi-mode interferometer (MMI). The excess insertion losses are below 4dB for the C-band, while the transmission imbalance is below 1.2dB. When such an optical hybrid was integrated vertically with mesa-type photodiodes, the responsivity of the individual PD was around 0.06 A/W, while the 3 dB bandwidth reaches 24 ~ 27 GHz, which is sufficient for 100Gbit/s receivers. Another example of the hybrid integration was to couple the polymer waveguides to fiber by applying fiber grooves, whose typical loss value was 0.2 dB per-facet over a broad spectral range from 1200-1600 nm.

Tunable thulium-doped fiber laser based on an abrupt-tapered in-fiber interferometer

NASA Astrophysics Data System (ADS)

Hernández-Arriaga, M. V.; Durán-Sánchez, M.; Ibarra-Escamilla, B.; Álvarez-Tamayo, R. I.; Santiago-Hernández, H.; Bello-Jiménez, M.; Kuzin, E. A.

2017-11-01

An experimental study of an all-fiber tunable thulium-doped fiber laser based on an abrupt-tapered in-fiber interferometer is presented. A microfiber filter with length of 6 mm and diameter of 20 μm is used to achieve single laser wavelength tuning in a range of 19.4 nm and dual-wavelength laser operation at 1761.8 and 1793.4 nm with a channel spacing of 31.6 nm. The abrupt-tapered structure allows multi-modal interference at the air-cladding interface. The proposed in-fiber interferometer exhibits characteristics of low cost and simple fabrication, making it suitable for practical applications in wavelength filtering and wavelength selection in all-fiber lasers.

THE IMPACT OF HUMANS ON CONTINENTAL EROSION AND SEDIMENTATION (Invited)

NASA Astrophysics Data System (ADS)

Wilkinson, B.; McElroy, B.

2009-12-01

Tectonic uplift and erosional denudation of orogenic belts have long been the most important geologic processes that serve to shape continental surfaces, but the rate of geomorphic change resulting from these natural phenomena has now been outstripped by human activities associated with agriculture, construction, and mining. Although humans are now the most important geomorphic agent on the planet’s surface, natural and anthropogenic processes serve to modify quite different parts of the Earth landscape. In order to better understand the impact of humans on continental erosion, we have examined both long-term and short-term data on rates of sediment transfer in response to glacio-fluvial and anthropogenic processes. Phanerozoic rates of subaerial denudation inferred from preserved volumes of sedimentary rock require a mean continental erosion rate on the order of 16 meters per million years (m/My), resulting in the accumulation of about 5 giga-tons of sediment per year (Gt/y). Erosion irregularly increased over the ~542 million year span of Phanerozoic time to a Pliocene value of 81 m/My (~19 Gt/y). Current estimates of large river sediment loads are similar to this late Neogene value, and require net denudation of ice-free land surfaces at a rate of about 74 m/My (~25 Gt/y). Consideration of variation in large river sediment loads and the geomorphology of respective river basin catchments suggests that natural erosion is primarily confined to drainage headwaters; ~83% of the global river sediment flux is derived from the highest 10% of the Earth’s surface. Subaerial erosion as a result of human activity, primarily through agricultural practices, has resulted in a sharp increase in net rates of continental denudation; although less well constrained than estimates based on surviving rock volumes or current river loads, available data suggest that present farmland denudation is proceeding at a rate of about 600 m/My (~74 Gt/y), and is largely confined to lower elevations of the Earth’s land surface, primarily along passive continental margins; ~83% of cropland erosion occurs over the lower 65% of the Earth’s surface. The conspicuous disparity between natural sediment fluxes suggested by data on rock volumes and river loads (~25 Gt/y) and anthropogenic fluxes inferred from measured and modeled cropland soil losses (74 Gt/y) is readily resolved by data on thicknesses and ages of alluvial sediment that has been deposited immediately down slope from eroding croplands over the history of human agriculture. Accumulation of post-settlement alluvium on higher order tributary channels and floodplains (mean rate ~12,600 m/My) is the most important geomorphic process in terms of the erosion and deposition of sediment that is currently shaping the landscape of the Earth. It far exceeds even the impact of Pleistocene continental glaciers or the current impact of alpine erosion by glacial and/or fluvial processes. Human beings are therefore the dominant agent of topographic change operating on the surface of the planet today.

Mercaptoheterocyclic ligands grafted on a poly(ethylene vinyl alcohol) membrane for the purification of immunoglobulin G in a salt independent thiophilic chromatography.

PubMed

Coffinier, Yannick; Vijayalakshmi, Mookambeswaran A

2004-08-25

In this study, we attempted a limited combinatorial approach for designing affinity ligands based on mercaptoheterocyclic components. The template, divinyl sulfone structure (DVS), which was grafted on poly(ethylene vinyl alcohol) (PEVA) hollow fiber membrane, has served for the tethering of different heterocyclic compounds as pyridine, imidazole, purine and pyrimidine rings. Their ability to adsorb specifically IgG in a salt independent manner out of pure IgG solution, mixture of IgG/albumin and human plasma was demonstrated. Mercapto methyl imidazole (MMI) has shown the best adsorption of IgG in terms of binding capacity. No subclass discrimination was observed on all tested ligands except for mercapto methyl pyrimidine where the major IgG subclass adsorbed was IgG3. MMI gave an IgG binding capacity of 100 microg/cm2 of hollow fiber membrane surface area.

Effect of thematic map misclassification on landscape multi-metric assessment.

PubMed

Kleindl, William J; Powell, Scott L; Hauer, F Richard

2015-06-01

Advancements in remote sensing and computational tools have increased our awareness of large-scale environmental problems, thereby creating a need for monitoring, assessment, and management at these scales. Over the last decade, several watershed and regional multi-metric indices have been developed to assist decision-makers with planning actions of these scales. However, these tools use remote-sensing products that are subject to land-cover misclassification, and these errors are rarely incorporated in the assessment results. Here, we examined the sensitivity of a landscape-scale multi-metric index (MMI) to error from thematic land-cover misclassification and the implications of this uncertainty for resource management decisions. Through a case study, we used a simplified floodplain MMI assessment tool, whose metrics were derived from Landsat thematic maps, to initially provide results that were naive to thematic misclassification error. Using a Monte Carlo simulation model, we then incorporated map misclassification error into our MMI, resulting in four important conclusions: (1) each metric had a different sensitivity to error; (2) within each metric, the bias between the error-naive metric scores and simulated scores that incorporate potential error varied in magnitude and direction depending on the underlying land cover at each assessment site; (3) collectively, when the metrics were combined into a multi-metric index, the effects were attenuated; and (4) the index bias indicated that our naive assessment model may overestimate floodplain condition of sites with limited human impacts and, to a lesser extent, either over- or underestimated floodplain condition of sites with mixed land use.

Antineutrophil Cytoplasmic Antibody-Positive Small-Vessel Vasculitis Associated with Antithyroid Drug Therapy: How Significant Is the Clinical Problem?

PubMed

Balavoine, Anne-Sophie; Glinoer, Daniel; Dubucquoi, Sylvain; Wémeau, Jean-Louis

2015-12-01

The aim of this review was to delineate the characteristics of antineutrophil cytoplasmic antibody (ANCA)-associated small-vessel vasculitis associated with antithyroid drugs (ATD). A PubMed search was made for English language articles using the search terms antithyroid drugs AND ANCA OR ANCA-associated vasculitis. The literature includes approximately 260 case reports of ANCA-associated small-vessel vasculitis related to ATD, with 75% of these associated with thiouracil derivatives (propylthiouracil [PTU]) and 25% with methyl-mercapto-imidazole derivatives (MMI/TMZ). The prevalence of ANCA-positive cases caused by ATD varied between 4% and 64% with PTU (median 30%), and 0% and 16% with MMI/TMZ (median 6%). Young age and the duration of ATD therapy were the main factors contributing to the emergence of ANCA positivity. Before ATD therapy initiation, the prevalence of ANCA-positive patients was 0-13%. During ATD administration, 20% of patients were found to be positive for ANCA. Only 15% of ANCA-positive patients treated with ATD exhibited clinical evidence of vasculitis, corresponding to 3% of all patients who received ATD. Clinical manifestations of ANCA-associated vasculitis related to ATD were extremely heterogeneous. When vasculitis occurred, ATD withdrawal was usually followed by rapid clinical improvement and a favorable prognosis. ANCA screening is not systematically recommended for individuals on ATD therapy, particularly given the decreasing use of PTU in favor of TMZ/MMI. Particular attention should be given to the pediatric population with Graves' disease who receive ATD, as well as patients treated with thiouracil derivatives and those on long-term ATD therapy.

Early effects of iodine deficiency on radial glial cells of the hippocampus of the rat fetus. A model of neurological cretinism.

PubMed Central

Martínez-Galán, J R; Pedraza, P; Santacana, M; Escobar del Ray, F; Morreale de Escobar, G; Ruiz-Marcos, A

1997-01-01

The most severe brain damage associated with thyroid dysfunction during development is observed in neurological cretins from areas with marked iodine deficiency. The damage is irreversible by birth and related to maternal hypothyroxinemia before mid gestation. However, direct evidence of this etiopathogenic mechanism is lacking. Rats were fed diets with a very low iodine content (LID), or LID supplemented with KI. Other rats were fed the breeding diet with a normal iodine content plus a goitrogen, methimazole (MMI). The concentrations of -thyroxine (T4) and 3,5,3'triiodo--thyronine (T3) were determined in the brain of 21-d-old fetuses. The proportion of radial glial cell fibers expressing nestin and glial fibrillary acidic protein was determined in the CA1 region of the hippocampus. T4 and T3 were decreased in the brain of the LID and MMI fetuses, as compared to their respective controls. The number of immature glial cell fibers, expressing nestin, was not affected, but the proportion of mature glial cell fibers, expressing glial fibrillary acidic protein, was significantly decreased by both LID and MMI treatment of the dams. These results show impaired maturation of cells involved in neuronal migration in the hippocampus, a region known to be affected in cretinism, at a stage of development equivalent to mid gestation in humans. The impairment is related to fetal cerebral thyroid hormone deficiency during a period of development when maternal thyroxinemia is believed to play an important role. PMID:9169500

A model of water and sediment balance as determinants of relative sea level rise in contemporary and future deltas

NASA Astrophysics Data System (ADS)

Tessler, Zachary D.; Vörösmarty, Charles J.; Overeem, Irina; Syvitski, James P. M.

2018-03-01

Modern deltas are dependent on human-mediated freshwater and sediment fluxes. Changes to these fluxes impact delta biogeophysical functioning and affect the long-term sustainability of these landscapes for human and for natural systems. Here we present contemporary estimates of long-term mean sediment balance and relative sea level rise across 46 global deltas. We model scenarios of contemporary and future water resource management schemes and hydropower infrastructure in upstream river basins to explore how changing sediment fluxes impact relative sea level rise in delta systems. Model results show that contemporary sediment fluxes, anthropogenic drivers of land subsidence, and sea level rise result in delta relative sea level rise rates that average 6.8 mm/y. Assessment of impacts of planned and under-construction dams on relative sea level rise rates suggests increases on the order of 1 mm/y in deltas with new upstream construction. Sediment fluxes are estimated to decrease by up to 60% in the Danube and 21% in the Ganges-Brahmaputra-Meghna if all currently planned dams are constructed. Reduced sediment retention on deltas caused by increased river channelization and management has a larger impact, increasing relative sea level rise on average by nearly 2 mm/y. Long-term delta sustainability requires a more complete understanding of how geophysical and anthropogenic change impact delta geomorphology. Local and regional strategies for sustainable delta management that focus on local and regional drivers of change, especially groundwater and hydrocarbon extraction and upstream dam construction, can be highly impactful even in the context of global climate-induced sea level rise.

Rates and patterns of late Cenozoic denudation in the northernmost Atlantic Coastal Plain and Piedmont

USGS Publications Warehouse

Stanford, S.D.; Ashley, G.M.; Russell, E.W.B.; Brenner, G.J.

2002-01-01

Topography of a 2800 km2 section of the U.S. Atlantic Coastal Plain and Piedmont is reconstructed at five times from the late Miocene to the Holocene. The reconstructions are based on mapping of fluvial, colluvial, and marginal-marine deposits that are dated by radiocarbon, palynostratigraphy, and correlation to adjacent glacial and marine units. Denudation rates and patterns are calculated by subtracting successive topographies, with 60 m horizontal resolution and 6 m vertical resolution. The overall late Miocene to Holocene denudation rate of 10 m/m.y. is similar to other estimates of long-term denudation in the region. The overall rate resolves spatially into a wide range of local rates, varying from a minimum of ???0.2 m/m.y. on residual uplands to as high as 600 m/m.y. in glacially rerouted stream channels. The distribution of local rates shows that denudation is accomplished by stream incision in response to long-term glacio-eustatic decline, followed by slope retreat into residual uplands from the incised channels. Slope retreat replaces the uplands with pediments and straths. Pediment landforms and sediments, and observation of modern scarps and valley heads, indicate that groundwater seepage from the base of residual uplands is an important mechanism of slope retreat. This process is self-limiting because as the volume of residual upland is reduced, seepage diminishes and slope retreat slows until small residuals undergo little or no further reduction. Thus, relict topography is preserved even as most of the landscape actively erodes.

Medial medullary infarction: clinical, imaging, and outcome study in 86 consecutive patients.

PubMed

Kim, Jong S; Han, Young S

2009-10-01

Clinical-imaging correlation and long-term clinical outcomes remain to be investigated in medial medullary infarction (MMI). We studied clinical, MRI, and angiographic data of 86 consecutive MMI patients. The lesions were correlated with clinical findings, and long-term outcomes, divided into mild and severe (modified Rankin scale >3), were assessed by telephone interview. Central poststroke pain (CPSP) was defined as persistent pain with visual numeric scale > or = 4. The lesions were located mostly in the rostral medulla (rostral 76%, rostral+middle 16%), while ventro-dorsal lesion patterns include ventral (V, 20%), ventral+middle (VM, 33%), and ventral+middle+dorsal (VMD, 41%). Clinical manifestations included motor dysfunction in 78 patients (91%), sensory dysfunction in 59 (73%), and vertigo/dizziness in 51 (59%), each closely related to involvement of ventral, middle, and dorsal portions, respectively (P<0.001, each). Vertebral artery (VA) atherosclerotic disease relevant to the infarction occurred in 53 (62%) patients, mostly producing atheromatous branch occlusion (ABO). Small vessel disease (SVD) occurred in 24 (28%) patients. ABO was more closely related to VMD (versus V+VM) than was SVD (P=0.035). During follow-up (mean 71 months), 11 patients died, and recurrent strokes occurred in 11. Old age (P=0.001) and severe motor dysfunction at admission (P=0.001) were factors predicting poor prognosis. CPSP, occurring in 21 patients, was closely (P=0.013) related to poor clinical outcome. MMI usually presents with a rostral medullary lesion, with a good clinical ventro-dorsal imaging correlation, caused most frequently by ABO followed by SVD. A significant proportion of patients remain dependent or have CPSP.

Multiple mini-interview test characteristics: 'tis better to ask candidates to recall than to imagine.

PubMed

Eva, Kevin W; Macala, Catherine

2014-06-01

The multiple mini-interview (MMI), used to facilitate the selection of applicants in health professional programmes, has been shown to be capable of generating reliable data predictive of success. It is a process rather than a single instrument and therefore its psychometric properties can be expected to vary according to the stations generated, the alignment between the stations and the qualities an institution prioritises, and the outcomes used. The purpose of this study was to explore the MMI's test characteristics when station type is manipulated. A 12-station MMI was established in which four stations were presented in three different ways. These included: situational judgement (SJ) stations, in which applicants were asked to imagine what they would do in specific situations; behavioural interview (BI) stations, in which applicants were asked to recall what they did in experienced situations, and free form (FF) stations, which were unstructured in that the examiner was simply given a brief explanation of the intent of the station without further guidance on how to conduct the discussion. Four circuits of the 12 stations were run with one examiner within each station. Candidates and examiners were surveyed regarding their experience. The reliability of the scores derived from the assessment was analysed separately for each station type. A total of 41 medical school candidates participated after completing the regular admission process. Although the score assigned did not differ across station type, BI stations more reliably differentiated between candidates (g = 0.77) than did the other station types (SJ, g = 0.69; FF, g = 0.66). The correlation between actual MMI scores and BI stations was also greatest (BI, r = 0.57; SJ, r = 0.45; FF, r = 0.42). Candidates' opinions indicated that FF stations were more anxiety-provoking, less clear, and more difficult than structured stations (SJ and BI stations). Examiner opinions indicated equivalence on these measures. The results suggest that structuring stations has value, although that value was gained only through the use of BI stations, in which candidates were asked to recall and discuss a specific experience of relevance to the purpose of the interview station. © 2014 John Wiley & Sons Ltd.

Using 10Be to quantify rates of landscape change in 'dead' orogens - millennial scale rates of bedrock and basin-scale erosion in the southern and central Appalachian Mountains

NASA Astrophysics Data System (ADS)

Bierman, P. R.; Reusser, L.; Portenga, E.

2011-12-01

The Appalachian Mountain chain stretches north-south along the eastern margin of North America, in places rising a thousand meters and more above the adjacent piedmont. Here, Davis built his paradigm of landscape evolution, seeing landscape rejuvenation and dissected peneplains, a transient landscape. Hack saw the Appalachians as a dynamic system where topography was adjusted to rock strength, a steady-state landscape. Neither had quantitative data by which to test their theories. Today, we approach landscapes of the Appalachian Mountains quite differently. Over the past decade, we and others have measured in situ-produced 10Be in more than 300 samples of quartz isolated from Appalachian drainage basin sediments and in more than 100 samples from exposed Appalachian bedrock outcrops, most of which are on ridgelines. Samples have been collected from the Susquehanna, Potomac, and Shenandoah drainage basins as well as from the area around the Great Smoky Mountain National Park and the Blue Ridge escarpment, and from rivers draining from the Appalachians across the southeastern United States Piedmont. Most areas of the Appalachian Mountains are eroding only slowly; the average for all drainage basin samples analyzed to date is ~18 m/My (n=328). The highest basin-scale erosion rates, 25-70 m/My are found in the Appalachian Plateau and in the Great Smoky Mountains. Lower rates, on the order on 10-20 m/My, characterize the Shenandoah, Potomac, and Blue Ridge escarpment areas. There is a significant, positive relationship between basin-scale erosion rates and average basin slope. Steeper basins are in general eroding more rapidly than less steep basins. On the whole, the erosion rates of bedrock outcrops are either lower than or similar to those measured at a basin scale. The average erosion rate for samples of outcropping bedrock collected from the Appalachians is ~15 m/My (n=101). In the Potomac River Basin and the Great Smoky Mountains, bedrock and basin-scale erosion rates are similar implying long-term steady erosion consistent with dynamic steady state as advocated by Hack. However, in the Susquehanna drainage, basin scale erosion rates are significantly higher than those measured from outcrops suggesting that over time, relief is increasing. The Susquehanna River basin appears to be responding to a transient perturbation, ala Davis.

Damage and Shaking Intensity in the M5.7 Canyondam Earthquake

NASA Astrophysics Data System (ADS)

Boatwright, J.; Chapman, K.; Gold, M. B.; Hardebeck, J. L.

2013-12-01

An M5.7 earthquake occurred southeast of Lake Almanor, CA, at 8:47 PM on May 23, 2013. Double-difference relocations of the main shock and aftershocks indicate that the earthquake nucleated at 11 km depth and ruptured up dip on a fault striking 292° and dipping 70° to the northeast. The earthquake cracked foundations, broke chimneys, and ruptured plumbing around Lake Almanor. We canvassed communities around the lake and to the south and east for earthquake damage, adding reports from our interviews to the geocoded 'Did You Feel It?' reports and to a set of damage reports collected by the Plumas County Office of Emergency Services. Three communities suffered significant damage. In Lake Almanor West, 14 km and 290° from the hypocenter, one wood-frame house was shifted on its foundation, the cripple wall of another house was racked, and water and gas pipes in five houses were ruptured. This damage indicates the shaking approached MMI 8. In Lake Almanor Country Club, 10 km and 310° from the hypocenter, more than 40 chimneys were cracked, broken, or collapsed, a coupling for the municipal water tank was ruptured, and a 200-foot long fissure opened on a slope facing the lake. This damage indicates shaking between MMI 7 and MMI 8, consistent with the accelerograph recording of PGA = 38% g and PGV = 30 cm/s at the Fire Station in Lake Almanor Country Club. This CSMIP station and a PG&E station on the crest of the Butt Valley Dam obtained the only recordings within 50 km of the epicenter. In Hamilton Branch, 10 km and 345° from the hypocenter, a foundation of a wood-frame house was damaged, and 14 chimneys and a water pipe were broken, indicative of MMI 7 shaking. All three communities are underlain by Tertiary and Quaternary basalts. The communities of Chester, Westwood, and Greenville were less damaged, suffering cracked drywall, broken windows, and objects thrown from shelves. The intensities in the three most strongly damaged communities increase as the azimuth from the source approaches the fault strike. This damage pattern could be caused by rupture directivity if the earthquake or the strongest sub-event of the earthquake ruptured up dip and to the west.

Risk Factors for Tear Progression in Symptomatic Rotator Cuff Tears: A Prospective Study of 174 Shoulders.

PubMed

Yamamoto, Nobuyuki; Mineta, Mitsuyoshi; Kawakami, Jun; Sano, Hirotaka; Itoi, Eiji

2017-09-01

The risk factors for tear progression in symptomatic rotator cuff tears have not been clarified yet. It is important for orthopaedic surgeons to know the natural course of tear progression when nonoperative management is to be chosen. Tears in younger patients, high-activity patients, or heavy laborers would progress in size more than those in older patients, low-activity patients, or light laborers. Case-control study; Level of evidence, 3. Two hundred twenty-five consecutive patients with symptomatic rotator cuff tears visited our institute between 2009 and 2015. Of these, 174 shoulders of 171 patients (mean age, 66.9 years) who underwent at least 2 magnetic resonance imaging (MRI) examinations were prospectively enrolled. The mean follow-up was 19 months. Tear progression was defined as positive when the tear size increased by ≥2 mm. The demographic factors that were analyzed by multivariate analysis included age, sex, hand dominance, smoking, alcohol drinking, hypercholesterolemia, sports participation, job type, tear size, and tear type (full or partial thickness). Of the 174 shoulders, 82 shoulders (47%) showed tear progression. The mean (±SD) tear length and width in the progression group on final MRI were 23.1 ± 12.5 mm and 17.3 ± 9.6 mm, respectively; the tear size progressed by a mean 5.8 ± 5.6 mm in length and 3.1 ± 5.2 mm in width. The mean propagation speed was 3.8 mm/y in length and 2.0 mm/y in width. The size of full-thickness tears significantly increased compared with that of articular-sided partial-thickness tears ( P = .0215). The size of medium tears significantly increased compared with that of other tears ( P < .0001). According to the logistic regression analysis, smoking was significantly correlated with tear progression ( P = .026). Subgroup analyses showed that male sex, hand dominance, and trauma were correlated with tear progression. Age, alcohol drinking, hypercholesterolemia, sports participation, and job type did not show any correlation with tear progression. The tear size of symptomatic rotator cuff tears progressed in 47% of the shoulders during a mean of 19 months, and the speed of progression was 3.8 mm/y in length and 2.0 mm/y in width. The risk factors for tear progression were (1) a medium-sized tear, (2) a full-thickness tear, and (3) smoking.

Multiple mini interview (MMI) for general practice training selection in Australia: interviewers' motivation.

PubMed

Burgess, Annette; Roberts, Chris; Sureshkumar, Premala; Mossman, Karyn

2018-01-25

Multiple Mini Interviews (MMIs) are being used by a growing number of postgraduate training programs and medical schools as their interview process for selection entry. The Australian General Practice and Training (AGPT) used a National Assessment Centre (NAC) approach to selection into General Practice (GP) Training, which include MMIs. Interviewing is a resource intensive process, and implementation of the MMI requires a large number of interviewers, with a number of candidates being interviewed simultaneously. In 2015, 308 interviewers participated in the MMI process - a decrease from 340 interviewers in 2014, and 310 in 2013. At the same time, the number of applicants has steadily increased, with 1930 applications received in 2013; 2254 in 2014; and 2360 in 2015. This has raised concerns regarding the increasing recruitment needs, and the need to retain interviewers for subsequent years of MMIs. In order to investigate interviewers' reasons for participating in MMIs, we utilised self-determination theory (SDT) to consider interviewers' motivation to take part in MMIs at national selection centres. In 2015, 308 interviewers were recruited from 17 Regional Training Providers (RTPs) to participate in the MMI process at one of 15 NACs. For this study, a convenience sample of NAC sites was used. Forty interviewers were interviewed (n = 40; 40/308 = 13%) from five NACs. Framework analysis was used to code and categorise data into themes. Interviewers' motivation to take part as interviewers were largely related to their sense of duty, their desire to contribute their expertise to the process, and their desire to have input into selection of GP Registrars; a sense of duty to their profession; and an opportunity to meet with colleagues and future trainees. Interviewers also highlighted factors hindering motivation, which sometimes included the large number of candidates seen in one day. Interviewers' motivation for contributing to the MMIs was largely related to their desire to contribute to their profession, and ultimately improve future patient care. Interviewers recognised the importance of interviewing, and felt their individual roles made a crucial contribution to the profession of general practice. Good administration and leadership at each NAC is needed. By gaining an understanding of interviewers' motivation, and enhancing this, engagement and retention of interviewers may be increased.

77 FR 27503 - Self-Regulatory Organizations; The Depository Trust Company; Order Granting Approval of a...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-10

... maturing positions of MMI CUSIPs from a participant's accounts and credits the participant's account with... delivered to the account of the applicable issuing or paying agent (``IPA''),\\4\\ also a DTC [[Page 27504

Predicting macroinvertebrate MMI for geographic targeting

EPA Science Inventory

The US Environmental Protection Agency surveys the ecological conditions of streams across broad regions. We wish to identify specific streams in poor condition, as well as their regional extent. To identify such streams in Idaho, Oregon and Washington we built multiple regress...

Axial strain and temperature sensing characteristics of the single-coreless-single mode fiber structure-based fiber ring laser

NASA Astrophysics Data System (ADS)

Liu, Zhi-bo; Yin, Bin; Liang, Xiao; Bai, Yunlong; Tan, Zhongwei; Liu, Shuo; Li, Yang; Liu, Yan; Jian, Shuisheng

2014-06-01

This paper experimentally demonstrated a singlemode-coreless-singlemode (SCS) fiber structure-based fiber ring cavity laser for strain and temperature measurement. The basis of the sensing system is the multimodal interference occurs in coreless fiber, and the transmission spectrum is sensitive to the ambient perturbation. In this sensing system, the SCS fiber structure not only acts as the sensing head of the sensor but also the band-pass filter of the ring laser. Blue shift with strain sensitivity of ˜ -2 pm/μɛ ranging from 0 to 730 μɛ and red shift with temperature sensitivity of ˜ 11 pm/°C ranging from 5 to 75 °C have been achieved. Experimental results also show the proposal has great potential in using long-distance operation. The fiber ring laser sensing system has a optical signal to noise ratio (OSNR) more than 50 and 3 dB bandwidth less than 0.05 nm. The result shows that the coreless fiber has no improvement of the temperature and axial strain sensitivity. However, compared to the common singlemode-multimode-singlemode fiber structure sensors, the laser sensing system has the additional advantages of high OSNR, high intensity and narrow 3 dB bandwidth, and thus improves the accuracy.

“RaMassays”: Synergistic Enhancement of Plasmon-Free Raman Scattering and Mass Spectrometry for Multimodal Analysis of Small Molecules

PubMed Central

Alessandri, Ivano; Vassalini, Irene; Bertuzzi, Michela; Bontempi, Nicolò; Memo, Maurizio; Gianoncelli, Alessandra

2016-01-01

SiO2/TiO2 core/shell (T-rex) beads were exploited as “all-in-one” building-block materials to create analytical assays that combine plasmon-free surface enhanced Raman scattering (SERS) and surface assisted laser desorption/ionization (SALDI) mass spectrometry (RaMassays). Such a multi-modal approach relies on the unique optical properties of T-rex beads, which are able to harvest and manage light in both UV and Vis range, making ionization and Raman scattering more efficient. RaMassays were successfully applied to the detection of small (molecular weight, M.W. <400 Da) molecules with a key relevance in biochemistry and pharmaceutical analysis. Caffeine and cocaine were utilized as molecular probes to test the combined SERS/SALDI response of RaMassays, showing excellent sensitivity and reproducibility. The differentiation between amphetamine/ephedrine and theophylline/theobromine couples demonstrated the synergistic reciprocal reinforcement of SERS and SALDI. Finally, the conversion of L-tyrosine in L-DOPA was utilized to probe RaMassays as analytical tools for characterizing reaction intermediates without introducing any spurious effects. RaMassays exhibit important advantages over plasmonic nanoparticles in terms of reproducibility, absence of interference and potential integration in multiplexed devices. PMID:27698368

Multi-species sensing using multi-mode absorption spectroscopy with mid-infrared interband cascade lasers

NASA Astrophysics Data System (ADS)

O'Hagan, S.; Northern, J. H.; Gras, B.; Ewart, P.; Kim, C. S.; Kim, M.; Merritt, C. D.; Bewley, W. W.; Canedy, C. L.; Vurgaftman, I.; Meyer, J. R.

2016-06-01

The application of an interband cascade laser, ICL, to multi-mode absorption spectroscopy, MUMAS, in the mid-infrared region is reported. Measurements of individual mode linewidths of the ICL, derived from the pressure dependence of lineshapes in MUMAS signatures of single, isolated, lines in the spectrum of HCl, were found to be in the range 10-80 MHz. Multi-line spectra of methane were recorded using spectrally limited bandwidths, of approximate width 27 cm-1, defined by an interference filter, and consist of approximately 80 modes at spectral locations spanning the 100 cm-1 bandwidth of the ICL output. Calibration of the methane pressures derived from MUMAS data using a capacitance manometer provided measurements with an uncertainty of 1.1 %. Multi-species sensing is demonstrated by the simultaneous detection of methane, acetylene and formaldehyde in a gas mixture. Individual partial pressures of the three gases are derived from best fits of model MUMAS signatures to the data with an experimental error of 10 %. Using an ICL, with an inter-mode interval of ~10 GHz, MUMAS spectra were recorded at pressures in the range 1-10 mbar, and, based on the data, a potential minimum detection limit of the order of 100 ppmv is estimated for MUMAS at atmospheric pressure using an inter-mode interval of 80 GHz.

High sensitivity optical fiber liquid level sensor based on a compact MMF-HCF-FBG structure

NASA Astrophysics Data System (ADS)

Zhang, Yunshan; Zhang, Weigang; Chen, Lei; Zhang, Yanxin; Wang, Song; Yan, Tieyi

2018-05-01

An ultra-high sensitivity fiber liquid level sensor based on wavelength demodulation is proposed and demonstrated. The sensor is composed of a segment of multimode fiber and a large aperture hollow-core fiber assisted by a fiber Bragg grating (FBG). Interference occurs due to core mismatching and different modes with different effective refractive indices. The experimental results show that the liquid level sensitivity of the sensor is 1.145 nm mm‑1, and the linearity is up to 0.996. The dynamic temperature compensation of the sensor can be achieved by cascading an FBG. Considering the high sensitivity and compact structure of the sensor, it can be used for real-time intelligent monitoring of tiny changes in liquid level.

Ultracompact splitter for submicrometer silicon-on-insulator rib waveguides.

PubMed

Koster, Alain; Cassan, Eric; Laval, Suzanne; Vivien, Laurent; Pascal, Daniel

2004-11-01

An ultracompact and efficient 1 x 2 splitter for submicrometer silicon-on-insulator rib waveguides using a star coupler is reported. The structure proposed here is decidedly smaller than the usual splitters such as multi-mode interference or Y-branch devices and much less sensitive to technological fluctuations. Design of the compact splitter is optimized at lambda = 1.31 microm with the effective-index method and a two-dimensional beam-propagation method. The excess losses are lower than 0.15 dB, and the dependence of the losses on wavelength between 1.23 and 1.63 microm is almost flat (variation less than 0.04 dB), which makes the device very interesting for coarse wavelength-division multiplexing applications within the silicon photonic technology.

Tapered GRIN fiber microsensor.

PubMed

Beltrán-Mejía, Felipe; Biazoli, Claudecir R; Cordeiro, Cristiano M B

2014-12-15

The sensitivity of an optical fiber microsensor based on inter-modal interference can be considerably improved by tapering a short extension of the multimode fiber. In the case of Graded Index fibers with a parabolic refractive index profile, a meridional ray exhibits a sinusoidal path. When these fibers are tapered, the period of the propagated beam decrease down-taper and increase up-taper. We take advantage of this modulation -along with the enhanced overlap between the evanescent field and the external medium- to substantially increase the sensitivity of these devices by tuning the sensor's maximum sensitivity wavelength. Moreover, the extension of this device is reduced by one order of magnitude, making it more propitious for reduced space applications. Numerical and experimental results demonstrate the success and feasibility of this approach.

Basin Wide Erosion and Soil Production Rates of a High Altitude Plateau in the Korean Peninsula Considered as an Uplifted Paleo Erosional Surface: Implications for Its Development Process and the Tectonics

NASA Astrophysics Data System (ADS)

Byun, J.; Seong, Y.

2012-12-01

The development process of High Altitude Plateaus (HAPs) has been a controversial issue in geomorphology. HAPs have been interpreted as uplifted erosional surfaces mainly controlled by fluvial processes. Recent studies, however, argued that the definition of the Paleo Erosional Surfaces (PESs) is ambiguous and HAPs, considered as the uplifted PESs, could be formed under various local lithologic, tectonic and climatic conditions. But these suggestions were severely limited by the lack of quantitative data in the field. Here, we investigate this issue of the development process of HAPs through estimating both basin wide erosion rates and soil production rates of the Daegwanryeong area in the Korean Peninsula (KP), where a HAP with low-relief hilly landscape is found. Study area has been known as a typical one of PESs in the KP, which have been uplifted since the early Miocene. Particularly deeply weathered saprolites, easily found in the study area, have also been believed to be resulted from the Tertiary deep weathering under higher temperature at the paleo sea level. First, analysis of 10Be in saprolite from the base of the soil column, except one under no soil mantle, shows that soil production rates decline linearly with increasing soil depth. These data provide a soil production function with a maximum soil production rate of 70.6m/m.y. under 24cm of soil and a minimum of 22m/m.y. under 75cm of soil. Accordingly it means that the interface between soil and saprolite have gone down maximum 141.2 m since the Quaternary. Thus it suggests that the saprolites are the results under current local climatic and geomorphic conditions rather than the relict of the Tertiary deep weathering. Second, measurements of 10Be in alluvial sediments show that the average erosion rate (70.7m/m.y.) of the study area is close to the maximum soil production rate, thus basin wide erosion rates of the study area are controlled by the current soil production rates. It means that about 1,400m has been eroded off since the early Miocene, when uplift of the KP seems to begin. Consequently it is difficult to think the HAP of the study area as the PES as well as one, which has been eroded keeping the original form of the PES. Furthermore, the erosion rates are lower than the uplift rates during the late Quaternary (about 300m/m.y.), but similar to the uplift rates before the early Miocene (about 100m/m.y.). Therefore, it suggests that the HAP of the study area has been uplifted since the early Miocene, but has not approached the steady state with the neotectonics of the KP. In summary, we suggest that the HAP of the study area is the result of the geomorphic process under current climatic and geomorphic condition rather than the relict of the PES.

Quantification of fluvial response to tectonic deformation in the Central Pontides, Turkey; inferences from OSL dating of fluvial terraces

NASA Astrophysics Data System (ADS)

McClain, Kevin; Yıldırım, Cengiz; Çiner, Attila; Akif Sarıkaya, M.; Şahin, Sefa; Özcan, Orkan; Güneç Kıyak, Nafiye; Öztürk, Tuǧba

2017-04-01

From Late Miocene to present, Anatolia's rapid counterclockwise movement, which increases in velocity towards the Hellenic Arc, has formed the North Anatolian Fault (NAF), a dextral transform fault along the Anatolia-Eurasia plate boundary and the northern margin of the Central Anatolian Plateau (CAP). A zone of transpression referred to as the Central Pontides exists between the broad restraining bend of the NAF and the Black Sea Basin, uplifting what is interpreted as a detached flower structure. Dating of Quaternary landforms in the eastern flank of the Central Pontides has helped to understand its recent deformation. However, in the western flank of the Central Pontides there is an absence of Quaternary studies, relatively quiet modern seismicity, and difficulties locating or observing fault scarps. This led us to use optically stimulated luminescence dating (OSL-dating) of fluvial terrace sediments and the study of geomorphic features to gain insight into the influence of climate and tectonics on landscape evolution of this area. In this area, the Filyos River crosses the Karabük Fault (reverse fault) and deeply incises a gorge through the Karabük Range before flowing towards the Black Sea. In the gorge an abundance of indicators of tectonic deformation were mapped, such as hanging valleys, wind gaps, bedrock gorges, landslides, steep V-shaped channels, tilted basins, as well as fluvial strath terraces. In particular, strath terraces of at least 8 levels within just 1.5 km of horizontal distance were examined. We used OSL-dating to estimate five deposition ages of fluvial strath terrace sediments, leading to an estimation of incision and uplift rates over time. Using three samples per terrace with strath elevations of 246 ± 0.2 m, 105.49 ± 0.2 m, 43.6 ± 0.2 m, 15.3 ± 0.2 m and 3.6 ± 0.2 m above the Filyos River, we determined corresponding ages of 841 ± 76 ka, 681 ± 49 ka, 386 ± 18 ka, 88 ± 5.1 ka and 50.9 ± 2.8 ka. Incision rates over time (oldest terrace to youngest) suggest uplift of 0.29 ± 0.03 mm/y, 0.16 ± 0.01 mm/y, 0.10 ± 0.01 mm/y, 0.17 ± 0.01 mm/y and 0.07 ± 0.004 mm/y. Collectively, our ages infer decelerating fluvial incision and rock uplift rates in the Karabük Range of the Central Pontides. The highest rate that belongs to oldest terrace level (841 ± 76 ka) also implies long-term mean uplift, which is well correlated with long term ( 350 ka) mean uplift rate obtained from fluvial terraces in the eastern flank of the (Gökırmak Basin) Central Pontides. These results indicate Quaternary activity of the Karabük Fault despite the fact that very low modern seismicity and partition of strain in the north of the North Anatolian Fault. Keywords: Tectonics, Geomorphology, Fluvial Terrace, OSL Dating, Central Pontides, North Anatolian Fault, Filyos River, Turkey, Central Anatolian Plateau

Correlated Metrics Yield Multimetric Indices with Inferior Performance

EPA Science Inventory

Multimetric indices (MMIs) are widely used to assess the ecological health of freshwater ecosystems. An MMI is a sum of 5-15 standardized, numeric variables (or “metrics”), each representing a different attribute of a biological assemblage. Many researchers believe that highly co...

Down-regulated resistin level in consequence of decreased neutrophil counts in untreated Grave's disease.

PubMed

Peng, Ying; Qi, Yicheng; Huang, Fengjiao; Chen, Xinxin; Zhou, Yulin; Ye, Lei; Wang, Weiqing; Ning, Guang; Wang, Shu

2016-11-29

Resistin, belongs to cysteine-rich secretory protein, is mainly produced by circulating leukocytes, such as neutrophils monocytes and macrophages in humans. To date, few but controversial studies have reported about resistin concentrations in hyperthyroid patients, especially in Graves' disease (GD). We undertaked a controlled, prospective study to explore the serum resistin concentration in GD patients before and after -MMI treatment. In addition, we also investigated the main influencing factor on serum resistin level and discuessed the potential role of serum resistin plays in GD patients. 39 untreated GD (uGD) patients, including 8 males and 31 females, were enrolled in our investigation. All of these patients were prescribed with MMI treatment, in addition to 25 healthy controls. Anthropometric parameters and hormone assessment were measured. Enzyme-linked immunosorbent assay was used to detect serum resistin concentration in different stages of GD patients. Furthermore, neutrophil cell line NB4 with or without T3 treatment to detect the effect of thyroid hormones on resistin expression. The serum resistin level and neutrophil counts in untreated GD patients were significantly declined. And all of these parameters were recovered to normal after MMI treatment in ethyroid GD (eGD) and TRAb-negative conversion (nGD) patients. Resistin concentration exhibited a negative correlation with FT3 and FT4, but a positive correlation with absolute number of neutrophiles in uGD patients, whereas did not correlate with thyroid autoimmune antibodies and BMI. Neutrophile cell line, NB4, produced decreased expression of resistin when stimulated with T3. Our study showed a decrease of serum resistin level in GD patients and we suggested that the serum resistin might primarily secreted from circulating neutrophils and down-regulated by excessive thyroid hormones in GD patients.

Ability to return to work without restrictions in workers compensation patients undergoing hip arthroscopy

PubMed Central

Lee, Simon; Cvetanovich, Gregory L.; Mascarenhas, Randy; Wuerz, Thomas H.; Mather, Richard C.; Bush-Joseph, Charles A.

2017-01-01

Abstract The purpose of this study was to investigate the ability of worker’s compensation (WC) patients to return to work without restrictions after hip arthroscopy. Twenty-nine WC patients along with age and gender matched controls who underwent hip arthroscopy were retrospectively reviewed after achieving maximum medical improvement (MMI) status at minimum 1 year postoperatively. Patient demographic factors were evaluated, along with the Hip Outcome Score Activities of Daily Living and Sports-Specific subscales, and the modified Harris Hip Score (mHHS). The majority of WC patients were able to return to work without restrictions after reaching MMI (20/29, 69.0%). WC patients who failed to return to work without restrictions had a prolonged time from injury to surgery (3.01 ± 2.16 months versus 6.36 ± 4.16 months; P = 0.0079), more concomitant orthopedic injuries (4/20, 20.0% versus 9/9, 100%; P = 0.0001), and higher body mass index (BMI) (26.61 ± 3.52 versus 29.54 ± 3.43; P = 0.047) than those who returned to work without restrictions. WC patients had significant improvement of patient-reported outcome scores following hip arthroscopy (P < 0.0001), but WC patients who returned to work without restrictions had higher scores than those who failed to do so (HOD-ADL: P < 0.0001; HOS-SS: P = 0.004; mHHS: P = 0.009). The majority of WC patients are able to return to work without restrictions when they reach MMI status following hip arthroscopy. Factors associated with failure to return to work without restrictions include prolonged time course between injury and surgical treatment, concomitant orthopaedic injuries, and a higher BMI. Level III, retrospective case-control study PMID:28630718

Magnetic nanoparticle-mediated isolation of functional bacteria in a complex microbial community

PubMed Central

Zhang, Dayi; Berry, James P; Zhu, Di; Wang, Yun; Chen, Yin; Jiang, Bo; Huang, Shi; Langford, Harry; Li, Guanghe; Davison, Paul A; Xu, Jian; Aries, Eric; Huang, Wei E

2015-01-01

Although uncultured microorganisms have important roles in ecosystems, their ecophysiology in situ remains elusive owing to the difficulty of obtaining live cells from their natural habitats. In this study, we employed a novel magnetic nanoparticle-mediated isolation (MMI) method to recover metabolically active cells of a group of previously uncultured phenol degraders, Burkholderiales spp., from coking plant wastewater biosludge; five other culturable phenol degraders—Rhodococcus sp., Chryseobacterium sp. and three different Pseudomonas spp.—were also isolated from the same biosludge using traditional methods. The kinetics of phenol degradation by MMI-recovered cells (MRCs) was similar to that of the original sludge. Stable isotope probing (SIP) and pyrosequencing of the 16S rRNA from the ‘heavy' DNA (13C-DNA) fractions indicated that Burkholderiales spp. were the key phenol degraders in situ in the biosludge, consistent with the results of MRCs. Single-cell Raman micro-spectroscopy was applied to probe individual bacteria in the MRCs obtained from the SIP experiment and showed that 79% of them were fully 13C-labelled. Biolog assays on the MRCs revealed the impact of various carbon and nitrogen substrates on the efficiency of phenol degradation in the wastewater treatment plant biosludge. Specifically, hydroxylamine, a metabolite of ammonia oxidisation, but not nitrite, nitrate or ammonia, inhibited phenol degradation in the biosludge. Our results provided a novel insight into the occasional abrupt failure events that occur in the wastewater treatment plant. This study demonstrated that MMI is a powerful tool to recover live and functional cells in situ from a complex microbial community to enable further characterisation of their physiology. PMID:25191996

Changes in expression of T-helper (Th) 1- and Th2-associated chemokine receptors on peripheral blood lymphocytes and plasma concentrations of their ligands, interferon-inducible protein-10 and thymus and activation-regulated chemokine, after antithyroid drug administration in hyperthyroid patients with Graves' disease.

PubMed

Inukai, Yoshihisa; Momobayashi, Atsushi; Sugawara, Naoto; Aso, Yoshimasa

2007-06-01

Although Graves' disease is considered an autoantibody-mediated, T-helper 2 (Th2)-dominant disease, Th1-dominance may prevail in its initial phase. We longitudinally investigated Th1/Th2 balance in untreated hyperthyroid patients with Graves' disease after treatment of methimazole (MMI), an antithyroid drug. University clinic outpatients were studied prospectively. Subjects included 23 untreated hyperthyroid patients with Graves' disease and 17 age-matched control subjects. Before and after treatment, we measured Th1- and Th2-associated chemokine receptors (CXCR)3 and CCR4, on peripheral blood lymphocytes using flow cytometry, as well as plasma concentrations of their ligands, interferon-inducible protein (IP)-10 and thymus and activation-regulated chemokine (TARC). The percentage of CXCR3-expressing cells among CD4+T lymphocytes and plasma IP-10 was significantly higher in hyperthyroid Graves' disease patients than in controls. At 12 and 24 weeks after initiation of MMI, percentage of CXCR3-expressing CD4+T lymphocytes had decreased significantly, while the percentage of CCR4-expressing CD4+T lymphocytes had increased significantly at 24 weeks. The CXCR3/CCR4 ratio had decreased significantly at 24 weeks. Plasma concentrations of IP-10 had decreased significantly at 12 and 24 weeks. Plasma concentrations of TARC also had decreased significantly at 24 weeks. In hyperthyroid patients with Graves' disease in the active phase, Th1 cells rather than Th2 cells predominated among peripheral blood lymphocytes. After initiation of MMI, an ongoing transition from Th1 to Th2 dominance occurred.

Medical School Applicant Characteristics Associated With Performance in Multiple Mini-Interviews Versus Traditional Interviews: A Multi-Institutional Study.

PubMed

Henderson, Mark C; Kelly, Carolyn J; Griffin, Erin; Hall, Theodore R; Jerant, Anthony; Peterson, Ellena M; Rainwater, Julie A; Sousa, Francis J; Wofsy, David; Franks, Peter

2017-10-31

To examine applicant characteristics associated with multi mini-interview (MMI) or traditional interview (TI) performance at five California public medical schools. Of the five California Longitudinal Evaluation of Admissions Practices (CA-LEAP) consortium schools, three used TIs and two used MMIs. Schools provided the following retrospective data on all 2011-2013 admissions cycle interviewees: age, gender, race/ethnicity (under-represented in medicine [UIM] or not), self-identified disadvantaged (DA) status, undergraduate GPA, Medical College Admission Test (MCAT) score, and interview score (standardized as z-score, mean = 0, SD = 1). Adjusted linear regression analyses, stratified by interview type, examined associations with interview performance. The 4,993 applicants who completed 7,516 interviews included 931 (18.6%) UIM and 962 (19.3%) DA individuals; 3,226 (64.6%) had one interview. Mean age was 24.4 (SD = 2.7); mean GPA and MCAT score were 3.72 (SD = 0.22) and 33.6 (SD = 3.7), respectively. Older age, female gender, and number of prior interviews were associated with better performance on both MMIs and TIs. Higher GPA was associated with lower MMI scores (z-score, per unit GPA = -0.26, 95% CI [-0.45, -0.06]), but unrelated to TI scores. DA applicants had higher TI scores (z-score = 0.17, 95% CI [0.07, 0.28]), but lower MMI scores (z-score = -0.18, 95% CI [-0.28, -.08]) than non-DA applicants. Neither UIM status nor MCAT score were associated with interview performance. These findings have potentially important workforce implications, particularly regarding DA applicants, and illustrate the need for other multi-institutional studies of medical school admissions processes.

Light Exposure and Eye Growth in Childhood.

PubMed

Read, Scott A; Collins, Michael J; Vincent, Stephen J

2015-10-01

The purpose of this study was to examine the relationship between objectively measured ambient light exposure and longitudinal changes in axial eye growth in childhood. A total of 101 children (41 myopes and 60 nonmyopes), 10 to 15 years of age participated in this prospective longitudinal observational study. Axial eye growth was determined from measurements of ocular optical biometry collected at four study visits over an 18-month period. Each child's mean daily light exposure was derived from two periods (each 14 days long) of objective light exposure measurements from a wrist-worn light sensor. Over the 18-month study period, a modest but statistically significant association between greater average daily light exposure and slower axial eye growth was observed (P = 0.047). Other significant predictors of axial eye growth in this population included children's refractive error group (P < 0.001), sex (P < 0.01), and age (P < 0.001). Categorized according to their objectively measured average daily light exposure and adjusting for potential confounders (age, sex, baseline axial length, parental myopia, nearwork, and physical activity), children experiencing low average daily light exposure (mean daily light exposure: 459 ± 117 lux, annual eye growth: 0.13 mm/y) exhibited significantly greater eye growth than children experiencing moderate (842 ± 109 lux, 0.060 mm/y), and high (1455 ± 317 lux, 0.065 mm/y) average daily light exposure levels (P = 0.01). In this population of children, greater daily light exposure was associated with less axial eye growth over an 18-month period. These findings support the role of light exposure in the documented association between time spent outdoors and childhood myopia.

Using safety inspection data to estimate shaking intensity for the 1994 Northridge earthquake

USGS Publications Warehouse

Thywissen, K.; Boatwright, J.

1998-01-01

We map the shaking intensity suffered in Los Angeles County during the 17 January 1994, Northridge earthquake using municipal safety inspection data. The intensity is estimated from the number of buildings given red, yellow, or green tags, aggregated by census tract. Census tracts contain from 200 to 4000 residential buildings and have an average area of 6 km2 but are as small as 2 and 1 km2 in the most densely populated areas of the San Fernando Valley and downtown Los Angeles, respectively. In comparison, the zip code areas on which standard MMI intensity estimates are based are six times larger, on average, than the census tracts. We group the buildings by age (before and after 1940 and 1976), by number of housing units (one, two to four, and five or more), and by construction type, and we normalize the tags by the total number of similar buildings in each census tract. We analyze the seven most abundant building categories. The fragilities (the fraction of buildings in each category tagged within each intensity level) for these seven building categories are adjusted so that the intensity estimates agree. We calibrate the shaking intensity to correspond with the modified Mercalli intensities (MMI) estimated and compiled by Dewey et al. (1995); the shapes of the resulting isoseismals are similar, although we underestimate the extent of the MMI = 6 and 7 areas. The fragility varies significantly between different building categories (by factors of 10 to 20) and building ages (by factors of 2 to 6). The post-1940 wood-frame multi-family (???5 units) dwellings make up the most fragile building category, and the post-1940 wood-frame single-family dwellings make up the most resistant building category.

Sediment dispersal pattern in the Bay of Bengal - evidence for commencement of Bengal Fan sedimentation

NASA Astrophysics Data System (ADS)

Krishna, K. S.; Ismaiel, M.; Karlapati, S.; Gopala Rao, D.; Mishra, J.; D, S.

2015-12-01

The sediment succession in the Bay of Bengal records signatures corresponding to India-Asia collision, regional climate, and erosional processes of the Himalayan orogeny and the Indian subcontinent. The Bengal Fan - world's largest submarine fan - has been long studied to understand the link between the Himalayan tectonics and Asian monsoon climate, but early phase information of the Himalaya erosion is not retrieved from the Indian Ocean due to lack of deep-core samples. Therefore, the missing corresponding signals hampered the understanding of coupled processes between tectonics, climate and erosion. Seismic reflection profiles and industrial drill wells from the western Bay of Bengal show two different modes of sediment deposition: initially Indian peninsular rivers discharged sediments to the ocean at a rate ~20 m/m.y. until Oligocene-Miocene time (~23 Ma) with the exception of two fairly-enhanced sediment pulses from 65 to 54 and again from 34 to 23 Ma; since 23 Ma the Ganges and Brahmaputra rivers added huge volumes of sediments to the bay with variable rates range from 40 to >1000 m/m.y. Using seismic stratigraphic technique we found a distinct increase in sediment discharge (~140 m/m.y.) at 23 Ma is an important age marker for the onset of Bengal Fan sedimentation as a coupled connection between the Himalayan tectonics and Asian climate. Further rise in sedimentation rate during the period 6.8 - 0.8 Ma is surprisingly not in agreement with the decrease in sediment rate reported at ODP Leg 116 sites in the distal Bengal Fan, but coincident with the change in monsoon intensity. Here we provide well constrained ages for the growth of the Bengal Fan, which can serve as benchmark for interactions between the Himalayan exhumation and Asian climate.

Time Outdoors and Myopia Progression Over 2 Years in Chinese Children: The Anyang Childhood Eye Study.

PubMed

Li, Shi-Ming; Li, He; Li, Si-Yuan; Liu, Luo-Ru; Kang, Meng-Tian; Wang, Yi-Peng; Zhang, Fengju; Zhan, Si-Yan; Gopinath, Bamini; Mitchell, Paul; Wang, Ningli

2015-07-01

To investigate whether time outdoors and a range of other activities are associated with change in spherical equivalent (SE) and axial length in Chinese children over a period of 2 years. A total of 1997 children aged 12.7 ± 0.5 (10.9-15.6) years in the Anyang Childhood Eye Study (ACES) were examined annually (baseline and two follow-up visits). Myopia was defined as cycloplegic SE < -0.50 diopters (D). Questionnaires were administered to the students and parents at baseline to gauge time spent outdoors and on other tasks. We ran mixed linear models including age, sex, and years of follow-up. In the full cohort of children there was a suggestive association between time spent outdoors and change in axial length; however, the effect size was very small (high versus low tertile: -0.016 mm/y, P = 0.053). The association was observed in children not myopic at baseline (high versus low tertile, -0.036 mm/y; P = 0.009) but not in those already myopic at baseline (high versus low tertile: -0.005 mm/y; P = 0.595). Time outdoors and change in SE showed similar, but nonsignificant, relationships (P > 0.05), perhaps due to insufficient statistical power. The other activities examined and parental myopia were not associated with changes in SE and axial length (P > 0.11). Within the normal range of variation encountered in these Chinese children, a wide range of activities were largely unrelated to myopia progression at this age. However, there was suggestive evidence that greater time outdoors was associated with slower axial elongation in nonmyopic teenagers, but not in existing myopes.

Assessment of Ecological Quality of the Tajan River in Iran Using a Multimetric Macroinvertebrate Index and Species Traits

NASA Astrophysics Data System (ADS)

Aazami, Jaber; Esmaili Sari, Abbas; Abdoli, Asghar; Sohrabi, Hormoz; Van den Brink, Paul J.

2015-07-01

The objectives of this study were to assess the biological water of the Iranian Tajan River using different metrics, i.e., a Multimetric Macroinvertebrate Index (MMI) and a traits-based method. Twenty-eight physico-chemical parameters, 10 habitat factors, and abundance of macroinvertebrates were obtained for 17 sites. The Shahid-Rajaie dam divides the Tajan River into an up- and downstream part, with different land uses. Eighteen metrics were used to represent four components of ecosystem quality, including tolerance (Hilsenhoff, SIGNAL), diversity (Margalef, Shannon-Wiener, Simpson, and Evenness), abundance (total number of taxa, individuals, Ephemeroptera, Plecoptera, Trichoptera, EPT, and Insects), and composition of assemblages (% Ephemeroptera, % Plecoptera, % Trichoptera, and % EPT Taxa). The integrated MMI was calculated by averaging the obtained scores of all indices. In the next step, we gathered information on 22 biological traits of macroinvertebrates to evaluate whether (group of) traits could be identified that are indicative for specific or general stress. Result showed a decrease in MMI from upstream (very good water quality) to downstream (bad) due to human activities. Industrial activities like pulping and papermaking operations or sand mining in the downstream part had more effects than agriculture and fish ponds in the upstream part. A redundancy analysis biplot showed the variation between the modalities of trait of macroinvertebrates and their correlation with physico-chemical parameters in Tajan River. The findings show that traits can be indicative for different kind of stress but that more effort has to be put in gathering data sets to disentangle the effect of habitat quality, pollution, and the physico-chemical properties of high- versus lowland rivers.

Blood cell oxidative stress precedes hemolysis in whole blood-liver slice co-cultures of rat, dog, and human tissues

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vickers, Alison E.M., E-mail: vickers_alison@allergan.co; Sinclair, John R.; Fisher, Robyn L.

A novel in vitro model to investigate time-dependent and concentration-dependent responses in blood cells and hemolytic events is studied for rat, dog, and human tissues. Whole blood is co-cultured with a precision-cut liver slice. Methimazole (MMI) was selected as a reference compound, since metabolism of its imidazole thione moiety is linked with hematologic disorders and hepatotoxicity. An oxidative stress response occurred in all three species, marked by a decline in blood GSH levels by 24 h that progressed, and preceded hemolysis, which occurred at high MMI concentrations in the presence of a liver slice with rat (>= 1000 muM atmore » 48 h) and human tissues (>= 1000 muM at 48 h, >= 750 muM at 72 h) but not dog. Human blood-only cultures exhibited a decline of GSH levels but minimal to no hemolysis. The up-regulation of liver genes for heme degradation (Hmox1 and Prdx1), iron cellular transport (Slc40a1), and GSH synthesis and utilization (mGST1 and Gclc) were early markers of the oxidative stress response. The up-regulation of the Kupffer cell lectin Lgals3 gene expression indicated a response to damaged red blood cells, and Hp (haptoglobin) up-regulation is indicative of increased hemoglobin uptake. Up-regulation of liver IL-6 and IL-8 gene expression suggested an activation of an inflammatory response by liver endothelial cells. In summary, MMI exposure led to an oxidative stress response in blood cells, and an up-regulation of liver genes involved with oxidative stress and heme homeostasis, which was clearly separate and preceded frank hemolysis.« less

Assessment of ecological quality of the Tajan River in Iran using a multimetric macroinvertebrate index and species traits.

PubMed

Aazami, Jaber; Esmaili Sari, Abbas; Abdoli, Asghar; Sohrabi, Hormoz; Van den Brink, Paul J

2015-07-01

The objectives of this study were to assess the biological water of the Iranian Tajan River using different metrics, i.e., a Multimetric Macroinvertebrate Index (MMI) and a traits-based method. Twenty-eight physico-chemical parameters, 10 habitat factors, and abundance of macroinvertebrates were obtained for 17 sites. The Shahid-Rajaie dam divides the Tajan River into an up- and downstream part, with different land uses. Eighteen metrics were used to represent four components of ecosystem quality, including tolerance (Hilsenhoff, SIGNAL), diversity (Margalef, Shannon-Wiener, Simpson, and Evenness), abundance (total number of taxa, individuals, Ephemeroptera, Plecoptera, Trichoptera, EPT, and Insects), and composition of assemblages (% Ephemeroptera, % Plecoptera, % Trichoptera, and % EPT Taxa). The integrated MMI was calculated by averaging the obtained scores of all indices. In the next step, we gathered information on 22 biological traits of macroinvertebrates to evaluate whether (group of) traits could be identified that are indicative for specific or general stress. Result showed a decrease in MMI from upstream (very good water quality) to downstream (bad) due to human activities. Industrial activities like pulping and papermaking operations or sand mining in the downstream part had more effects than agriculture and fish ponds in the upstream part. A redundancy analysis biplot showed the variation between the modalities of trait of macroinvertebrates and their correlation with physico-chemical parameters in Tajan River. The findings show that traits can be indicative for different kind of stress but that more effort has to be put in gathering data sets to disentangle the effect of habitat quality, pollution, and the physico-chemical properties of high- versus lowland rivers.

Hypothyroidism and hyperthyroidism change ectoenzyme activity in rat platelets.

PubMed

Baldissarelli, Jucimara; Santi, Adriana; Schmatz, Roberta; Martins, Caroline C; Zanini, Daniela; Reichert, Karine P; Thomé, Gustavo R; Palma, Taís V; da Costa, Pauline; Morsch, Vera M; Schetinger, Maria R C

2018-04-16

The purinergic system has an important role in the regulation of vascular functions. The interference of thyroid hormones in this system and in cardiovascular events has been studied in recent years. However, the mechanisms involved in vascular, purinergic, and oxidative changes in thyroid disorders are not completely understood. Therefore, the present study aimed to assess purinergic enzyme activity in platelets from rats with hypothyroidism and hyperthyroidism induced, respectively, by continuous exposure to methimazole (MMI) at 20 mg/100 mL or L-thyroxine at 1.2 mg/100 mL in drinking water for 1 month. Results showed that rats exposed to L-thyroxine had a significant decrease in NTPDase activity, wherein ATP hydrolysis was 53% lower and ADP hydrolysis was 40% lower. Moreover, ecto-5'-nucleotidase activity was decreased in both groups, by 39% in the hypothyroidism group and by 52% in the hyperthyroidism group. On the other hand, adenosine deaminase (ADA) activity was increased in hyperthyroidism (75%), and nucleotide pyrophosphatase/phosphodiesterase (NPP) activity was increased in animals with hypothyroidism (127%) and those with hyperthyroidism (128%). Our findings suggest that changes in purinergic enzyme and purine levels could contribute to the undesirable effects of thyroid disturbances. Moreover, oxidative stress and, in particular, a high level of ROS production, showed a causal relation with changes in ectonucleotidase activity and nucleotide and nucleoside levels. © 2018 Wiley Periodicals, Inc.

Progress report on the Worldwide Earthquake Risk Management (WWERM) Program

USGS Publications Warehouse

Algermissen, S.T.; Hays, Walter W.; Krumpe, Paul R.

1992-01-01

Considerable progress has been made in the Worldwide Earthquake Risk Management (WWERM) Program since its initiation in late 1989 as a cooperative program of the Agency for International Development (AID), Office of U.S. Foreign Disaster Assistance (OFDA), and the U.S. Geological Survey. Probabilistic peak acceleration and peak Modified Mercalli intensity (MMI) maps have been prepared for Chile and for Sulawesi province in Indonesia. Earthquake risk (loss) studies for dwellings in Gorontalo, North Sulawesi, have been completed and risk studies for dwellings in selected areas of central Chile are underway. A special study of the effect of site response on earthquake ground motion estimation in central Chile has also been completed and indicates that site response may modify the ground shaking by as much as plus or minus two units of MMI. A program for the development of national probabilistic ground motion maps for the Philippines is now underway and pilot studies of earthquake ground motion and risk are being planned for Morocco.

MSFC personnel management tasks: Recruitment and orientation of new employees

NASA Technical Reports Server (NTRS)

Brindley, T. A.

1980-01-01

In order to encourage highly motivated young students to learn about NASA and consider it for a career, a formal program is to be initiated whereby selected students can work on a voluntary basis at Marshall Space Flight Center (MSFC). The first task was to develop the working plan and procedures for this program, called Student Volunteer Service Program, in the writing of MSFC official guidelines, the Marshall Management Instruction (the MMI) which is a binding document that defines policy and establishes procedures and guidelines. Particular considerations written into the MMI after numerous consultations, interviews, and discussions about a satisfactory policy, include: arrangements to be made between the student, the school authorities, and concerned MSFC employees; management of the work assignments; and procedures for the student's welfare and safety. The second task was the development of a recruitment brochure for the attraction of new employees, especially scientists and engineers. The third task assigned was to develop a plan called Orientation of New Employees.

Dietary, anthropometric, and biochemical determinants of uric acid in free-living adults

PubMed Central

2013-01-01

Background High plasma uric acid (UA) is a prerequisite for gout and is also associated with the metabolic syndrome and its components and consequently risk factors for cardiovascular diseases. Hence, the management of UA serum concentrations would be essential for the treatment and/or prevention of human diseases and, to that end, it is necessary to know what the main factors that control the uricemia increase. The aim of this study was to evaluate the main factors associated with higher uricemia values analyzing diet, body composition and biochemical markers. Methods 415 both gender individuals aged 21 to 82 years who participated in a lifestyle modification project were studied. Anthropometric evaluation consisted of weight and height measurements with later BMI estimation. Waist circumference was also measured. The muscle mass (Muscle Mass Index – MMI) and fat percentage were measured by bioimpedance. Dietary intake was estimated by 24-hour recalls with later quantification of the servings on the Brazilian food pyramid and the Healthy Eating Index. Uric acid, glucose, triglycerides (TG), total cholesterol, urea, creatinine, gamma-GT, albumin and calcium and HDL-c were quantified in serum by the dry-chemistry method. LDL-c was estimated by the Friedewald equation and ultrasensitive C-reactive protein (CRP) by the immunochemiluminiscence method. Statistical analysis was performed by the SAS software package, version 9.1. Linear regression (odds ratio) was performed with a 95% confidence interval (CI) in order to observe the odds ratio for presenting UA above the last quartile (♂UA > 6.5 mg/dL and ♀ UA > 5 mg/dL). The level of significance adopted was lower than 5%. Results Individuals with BMI ≥ 25 kg/m2 OR = 2.28(1.13-4.6) and lower MMI OR = 13.4 (5.21-34.56) showed greater chances of high UA levels even after all adjustments (gender, age, CRP, gamma-gt, LDL, creatinine, urea, albumin, HDL-c, TG, arterial hypertension and glucose). As regards biochemical markers, higher triglycerides OR = 2.76 (1.55-4.90), US-CRP OR = 2.77 (1.07-7.21) and urea OR = 2.53 (1.19-5.41) were associated with greater chances of high UA (adjusted for gender, age, BMI, waist circumference, MMI, glomerular filtration rate, and MS). No association was found between diet and UA. Conclusions The main factors associated with UA increase were altered BMI (overweight and obesity), muscle hypotrophy (MMI), higher levels of urea, triglycerides, and CRP. No dietary components were found among uricemia predictors. PMID:23311699

Evidence regarding the utility of multiple mini-interview (MMI) for selection to undergraduate health programs: A BEME systematic review: BEME Guide No. 37.

PubMed

Rees, Eliot L; Hawarden, Ashley W; Dent, Gordon; Hays, Richard; Bates, Joanna; Hassell, Andrew B

2016-05-01

In the 11 years since its development at McMaster University Medical School, the multiple mini-interview (MMI) has become a popular selection tool. We aimed to systematically explore, analyze and synthesize the evidence regarding MMIs for selection to undergraduate health programs. The review protocol was peer-reviewed and prospectively registered with the Best Evidence Medical Education (BEME) collaboration. Thirteen databases were searched through 34 terms and their Boolean combinations. Seven key journals were hand-searched since 2004. The reference sections of all included studies were screened. Studies meeting the inclusion criteria were coded independently by two reviewers using a modified BEME coding sheet. Extracted data were synthesized through narrative synthesis. A total of 4338 citations were identified and screened, resulting in 41 papers that met inclusion criteria. Thirty-two studies report data for selection to medicine, six for dentistry, three for veterinary medicine, one for pharmacy, one for nursing, one for rehabilitation, and one for health science. Five studies investigated selection to more than one profession. MMIs used for selection to undergraduate health programs appear to have reasonable feasibility, acceptability, validity, and reliability. Reliability is optimized by including 7-12 stations, each with one examiner. The evidence is stronger for face validity, with more research needed to explore content validity and predictive validity. In published studies, MMIs do not appear biased against applicants on the basis of age, gender, or socio-economic status. However, applicants of certain ethnic and social backgrounds did less well in a very small number of published studies. Performance on MMIs does not correlate strongly with other measures of noncognitive attributes, such as personality inventories and measures of emotional intelligence. MMI does not automatically mean a more reliable selection process but it can do, if carefully designed. Effective MMIs require careful identification of the noncognitive attributes sought by the program and institution. Attention needs to be given to the number of stations, the blueprint and examiner training. More work is required on MMIs as they may disadvantage groups of certain ethnic or social backgrounds. There is a compelling argument for multi-institutional studies to investigate areas such as the relationship of MMI content to curriculum domains, graduate outcomes, and social missions; relationships of applicants' performance on different MMIs; bias in selecting applicants of minority groups; and the long-term outcomes appropriate for studies of predictive validity.

The Intersection of Multimodality and Critical Perspective: Multimodality as Subversion

ERIC Educational Resources Information Center

Huang, Shin-ying

2015-01-01

This study explores the relevance of multimodality to critical media literacy. It is based on the understanding that communication is intrinsically multimodal and multimodal communication is inherently social and ideological. By analysing two English-language learners' multimodal ensembles, the study reports on how multimodality contributes to a…

Expansion, Differentiation, and the Persistence of Social Class Inequalities in British Higher Education

ERIC Educational Resources Information Center

Boliver, Vikki

2011-01-01

Conventional political wisdom has it that educational expansion helps to reduce socioeconomic inequalities of access to education by increasing equality of educational opportunity. The counterarguments of Maximally Maintained Inequality (MMI) and Effectively Maintained Inequality (EMI), in contrast, contend that educational inequalities tend to…

The role of group index engineering in series-connected photonic crystal microcavities for high density sensor microarrays

PubMed Central

Zou, Yi; Chakravarty, Swapnajit; Zhu, Liang; Chen, Ray T.

2014-01-01

We experimentally demonstrate an efficient and robust method for series connection of photonic crystal microcavities that are coupled to photonic crystal waveguides in the slow light transmission regime. We demonstrate that group index taper engineering provides excellent optical impedance matching between the input and output strip waveguides and the photonic crystal waveguide, a nearly flat transmission over the entire guided mode spectrum and clear multi-resonance peaks corresponding to individual microcavities that are connected in series. Series connected photonic crystal microcavities are further multiplexed in parallel using cascaded multimode interference power splitters to generate a high density silicon nanophotonic microarray comprising 64 photonic crystal microcavity sensors, all of which are interrogated simultaneously at the same instant of time. PMID:25316921

A multi-modal stereo microscope based on a spatial light modulator.

PubMed

Lee, M P; Gibson, G M; Bowman, R; Bernet, S; Ritsch-Marte, M; Phillips, D B; Padgett, M J

2013-07-15

Spatial Light Modulators (SLMs) can emulate the classic microscopy techniques, including differential interference (DIC) contrast and (spiral) phase contrast. Their programmability entails the benefit of flexibility or the option to multiplex images, for single-shot quantitative imaging or for simultaneous multi-plane imaging (depth-of-field multiplexing). We report the development of a microscope sharing many of the previously demonstrated capabilities, within a holographic implementation of a stereo microscope. Furthermore, we use the SLM to combine stereo microscopy with a refocusing filter and with a darkfield filter. The instrument is built around a custom inverted microscope and equipped with an SLM which gives various imaging modes laterally displaced on the same camera chip. In addition, there is a wide angle camera for visualisation of a larger region of the sample.

Use of unnatural amino acids to probe structure-activity relationships and mode-of-action of antimicrobial peptides.

PubMed

Tossi, Alessandro; Scocchi, Marco; Zahariev, Sotir; Gennaro, Renato

2012-01-01

Endogenous antimicrobial peptides (AMPs) can have multimodal mechanisms of bacterial inactivation, such as membrane lysis, interference with cell wall biosynthesis or membrane-based protein machineries, or translocation through the membrane to intracellular targets. The controlled variation of side-chain characteristics in their amino acid residues can provide much useful information on structure-activity relationships and mode-of-action, and also lead to improved activities. The small size and relatively low complexity of AMPs make them amenable to solid-phase peptide synthesis, facilitating the use of nonproteinogenic amino acids and vastly increasing the accessible molecular diversity of side chains. Here, we describe how such residues can be used to modulate such key parameters as cationicity, hydrophobicity, steric factors conformational stability, and H-bonding.

Strain Accumulation Estimated from Seafloor Crustal Deformation at the Nankai Trough, Japan

NASA Astrophysics Data System (ADS)

Tadokoro, K.; Watanabe, T.; Nagai, S.; Ikuta, R.; Okuda, T.; Kenji, Y.; Sakata, T.

2012-12-01

Our research has developed an observation system for seafloor crustal deformation composed of the kinematic GPS and acoustic ranging techniques [Tadokoro et al., 2006; Ikuta et al., 2008]. We monitored crustal deformation at the Nankai Trough, Japan, where the Philippine Sea Plate subducts beneath the Amurian Plate. The convergence rate is predicted at 60 mm/y in the N59W direction by the Euler vector of REVEL [Sella et al., 2002]. We installed three monitoring sites (named KMN, KMS, and KME) on the seafloor at depths of about 1920-2030 m. The sites KMN and KMS are installed perpendicular to the trough axis with a spacing of 20 km; the site KME is 50 km from KMN and KMS in the direction parallel to the trough axis. The monitoring was started in 2004, 2005, and 2008 at KMS, KMN, and KME, respectively. The numbers of measurements are 16, 20, and 5 times at KMN, KMS, and KME, respectively. We obtained 3-7 years averaged horizontal site velocities within ITRF2000 adopting a robust estimation method with Tukey's biweight function to the time series of site position measured until the end of 2011. Substituting the synthetic rigid block motions of the Amurian Plate from the velocities within ITRF2000, we obtained the following site velocities with respect to the Amurian Plate [Tadokoro et al., 2012]: KMN 41±4 mm/y, N77±7W KMS 43±5 mm/y, N80±6W KME 42±5 mm/y, N80±7W In contrast, the on-land GPS horizontal velocities along the coast is 23-33 mm/y toward N74-80W. The present observational results show: (1) the velocity vectors are all the same length and direction, which indicates no internal deformation in this region; (2) the back-slip model predicts that the plate interface beneath the region is uniformly locked with coupling ratios of 60-80 %, indicating strain accumulation that will be released during the anticipated mega-thrust Tonankai earthquake; and (3) the directions of site velocities differ from that of convergence vector by 20 degrees, which is affected by the oblique subduction of the Philippine Sea Plate. We started monitoring of seafloor crustal deformation at a new site, KMC, in this year. This site is located between KMN and KMS. The monitoring at KMC enable us to depict dense (with a span of 10 km) crustal deformation profile that is related to strain accumulation, in the direction perpendicular to the trough axis. We plan to measure the position at KMC twice by the end of this year. We also continue to measure the position at KMS and KME. The number of measurements at KME is extremely few compared to the other sites in particular, and it is important to continue the measurement for obtaining stable site velocity. We report the results of monitoring preformed in this year. Acknowledgments: We are grateful to the captain and crews of R/V "Asama" of Mie Prefecture Fisheries Research Institute, Japan. This study has been partly promoted by Ministry of Education, Culture, Sports, Science and Technology, Japanese Government.

A multifunctional probe for ICP-MS determination and multimodal imaging of cancer cells.

PubMed

Yang, Bin; Zhang, Yuan; Chen, Beibei; He, Man; Yin, Xiao; Wang, Han; Li, Xiaoting; Hu, Bin

2017-10-15

Inductively coupled plasma-mass spectrometry (ICP-MS) based bioassay and multimodal imaging have attracted increasing attention in the current development of cancer research and theranostics. Herein, a sensitive, simple, timesaving, and reliable immunoassay for cancer cells counting and dual-modal imaging was proposed by using ICP-MS detection and down-conversion fluorescence (FL)/upconversion luminescence (UCL) with the aid of a multifunctional probe for the first time. The probe consisted of a recognition unit of goat anti-mouse IgG to label the anti-EpCAM antibody attached cells, a fluorescent dye (Cy3) moiety for FL imaging as well as upconversion nanoparticles (UCNPs) tag for both ICP-MS quantification and UCL imaging of cancer cells. Under the optimized conditions, an excellent linearity and sensitivity were achieved owing to the signal amplification effect of nanoparticles and low spectral interference. Accordingly, a limit of detection (3σ) of 1×10 2 HepG2 cells and a relative standard deviation of 7.1% for seven replicate determinations of 1×10 3 HepG2 cells were obtained. This work proposed a method to employ UCNPs with highly integrated functionalities enabling us not only to count but also to see the cancer cells, opening a promising avenue for biological research and clinical theranostics. Copyright © 2017 Elsevier B.V. All rights reserved.

FPGA-based RF interference reduction techniques for simultaneous PET–MRI

PubMed Central

Gebhardt, P; Wehner, J; Weissler, B; Botnar, R; Marsden, P K; Schulz, V

2016-01-01

Abstract The combination of positron emission tomography (PET) and magnetic resonance imaging (MRI) as a multi-modal imaging technique is considered very promising and powerful with regard to in vivo disease progression examination, therapy response monitoring and drug development. However, PET–MRI system design enabling simultaneous operation with unaffected intrinsic performance of both modalities is challenging. As one of the major issues, both the PET detectors and the MRI radio-frequency (RF) subsystem are exposed to electromagnetic (EM) interference, which may lead to PET and MRI signal-to-noise ratio (SNR) deteriorations. Early digitization of electronic PET signals within the MRI bore helps to preserve PET SNR, but occurs at the expense of increased amount of PET electronics inside the MRI and associated RF field emissions. This raises the likelihood of PET-related MRI interference by coupling into the MRI RF coil unwanted spurious signals considered as RF noise, as it degrades MRI SNR and results in MR image artefacts. RF shielding of PET detectors is a commonly used technique to reduce PET-related RF interferences, but can introduce eddy-current-related MRI disturbances and hinder the highest system integration. In this paper, we present RF interference reduction methods which rely on EM field coupling–decoupling principles of RF receive coils rather than suppressing emitted fields. By modifying clock frequencies and changing clock phase relations of digital circuits, the resulting RF field emission is optimised with regard to a lower field coupling into the MRI RF coil, thereby increasing the RF silence of PET detectors. Our methods are demonstrated by performing FPGA-based clock frequency and phase shifting of digital silicon photo-multipliers (dSiPMs) used in the PET modules of our MR-compatible Hyperion IID PET insert. We present simulations and magnetic-field map scans visualising the impact of altered clock phase pattern on the spatial RF field distribution, followed by MRI noise and SNR scans performed with an operating PET module using different clock frequencies and phase patterns. The methods were implemented via firmware design changes without any hardware modifications. This introduces new means of flexibility by enabling adaptive RF interference reduction optimisations in the field, e.g. when using a PET insert with different MRI systems or when different MRI RF coil types are to be operated with the same PET detector. PMID:27049898

FPGA-based RF interference reduction techniques for simultaneous PET-MRI.

PubMed

Gebhardt, P; Wehner, J; Weissler, B; Botnar, R; Marsden, P K; Schulz, V

2016-05-07

The combination of positron emission tomography (PET) and magnetic resonance imaging (MRI) as a multi-modal imaging technique is considered very promising and powerful with regard to in vivo disease progression examination, therapy response monitoring and drug development. However, PET-MRI system design enabling simultaneous operation with unaffected intrinsic performance of both modalities is challenging. As one of the major issues, both the PET detectors and the MRI radio-frequency (RF) subsystem are exposed to electromagnetic (EM) interference, which may lead to PET and MRI signal-to-noise ratio (SNR) deteriorations. Early digitization of electronic PET signals within the MRI bore helps to preserve PET SNR, but occurs at the expense of increased amount of PET electronics inside the MRI and associated RF field emissions. This raises the likelihood of PET-related MRI interference by coupling into the MRI RF coil unwanted spurious signals considered as RF noise, as it degrades MRI SNR and results in MR image artefacts. RF shielding of PET detectors is a commonly used technique to reduce PET-related RF interferences, but can introduce eddy-current-related MRI disturbances and hinder the highest system integration. In this paper, we present RF interference reduction methods which rely on EM field coupling-decoupling principles of RF receive coils rather than suppressing emitted fields. By modifying clock frequencies and changing clock phase relations of digital circuits, the resulting RF field emission is optimised with regard to a lower field coupling into the MRI RF coil, thereby increasing the RF silence of PET detectors. Our methods are demonstrated by performing FPGA-based clock frequency and phase shifting of digital silicon photo-multipliers (dSiPMs) used in the PET modules of our MR-compatible Hyperion II (D) PET insert. We present simulations and magnetic-field map scans visualising the impact of altered clock phase pattern on the spatial RF field distribution, followed by MRI noise and SNR scans performed with an operating PET module using different clock frequencies and phase patterns. The methods were implemented via firmware design changes without any hardware modifications. This introduces new means of flexibility by enabling adaptive RF interference reduction optimisations in the field, e.g. when using a PET insert with different MRI systems or when different MRI RF coil types are to be operated with the same PET detector.

FPGA-based RF interference reduction techniques for simultaneous PET-MRI

NASA Astrophysics Data System (ADS)

Gebhardt, P.; Wehner, J.; Weissler, B.; Botnar, R.; Marsden, P. K.; Schulz, V.

2016-05-01

The combination of positron emission tomography (PET) and magnetic resonance imaging (MRI) as a multi-modal imaging technique is considered very promising and powerful with regard to in vivo disease progression examination, therapy response monitoring and drug development. However, PET-MRI system design enabling simultaneous operation with unaffected intrinsic performance of both modalities is challenging. As one of the major issues, both the PET detectors and the MRI radio-frequency (RF) subsystem are exposed to electromagnetic (EM) interference, which may lead to PET and MRI signal-to-noise ratio (SNR) deteriorations. Early digitization of electronic PET signals within the MRI bore helps to preserve PET SNR, but occurs at the expense of increased amount of PET electronics inside the MRI and associated RF field emissions. This raises the likelihood of PET-related MRI interference by coupling into the MRI RF coil unwanted spurious signals considered as RF noise, as it degrades MRI SNR and results in MR image artefacts. RF shielding of PET detectors is a commonly used technique to reduce PET-related RF interferences, but can introduce eddy-current-related MRI disturbances and hinder the highest system integration. In this paper, we present RF interference reduction methods which rely on EM field coupling-decoupling principles of RF receive coils rather than suppressing emitted fields. By modifying clock frequencies and changing clock phase relations of digital circuits, the resulting RF field emission is optimised with regard to a lower field coupling into the MRI RF coil, thereby increasing the RF silence of PET detectors. Our methods are demonstrated by performing FPGA-based clock frequency and phase shifting of digital silicon photo-multipliers (dSiPMs) used in the PET modules of our MR-compatible Hyperion II D PET insert. We present simulations and magnetic-field map scans visualising the impact of altered clock phase pattern on the spatial RF field distribution, followed by MRI noise and SNR scans performed with an operating PET module using different clock frequencies and phase patterns. The methods were implemented via firmware design changes without any hardware modifications. This introduces new means of flexibility by enabling adaptive RF interference reduction optimisations in the field, e.g. when using a PET insert with different MRI systems or when different MRI RF coil types are to be operated with the same PET detector.

Examination of tapered plastic multimode fiber-based sensor performance with silver coating for different concentrations of calcium hypochlorite by soft computing methodologies--a comparative study.

PubMed

Zakaria, Rozalina; Sheng, Ong Yong; Wern, Kam; Shamshirband, Shahaboddin; Wahab, Ainuddin Wahid Abdul; Petković, Dalibor; Saboohi, Hadi

2014-05-01

A soft methodology study has been applied on tapered plastic multimode sensors. This study basically used tapered plastic multimode fiber [polymethyl methacrylate (PMMA)] optics as a sensor. The tapered PMMA fiber was fabricated using an etching method involving deionized water and acetone to achieve a waist diameter and length of 0.45 and 10 mm, respectively. In addition, a tapered PMMA probe, which was coated by silver film, was fabricated and demonstrated using a calcium hypochlorite (G70) solution. The working mechanism of such a device is based on the observation increment in the transmission of the sensor that is immersed in solutions at high concentrations. As the concentration was varied from 0 to 6 ppm, the output voltage of the sensor increased linearly. The silver film coating increased the sensitivity of the proposed sensor because of the effective cladding refractive index, which increases with the coating and thus allows more light to be transmitted from the tapered fiber. In this study, the polynomial and radial basis function (RBF) were applied as the kernel function of the support vector regression (SVR) to estimate and predict the output voltage response of the sensors with and without silver film according to experimental tests. Instead of minimizing the observed training error, SVR_poly and SVR_rbf were used in an attempt to minimize the generalization error bound so as to achieve generalized performance. An adaptive neuro-fuzzy interference system (ANFIS) approach was also investigated for comparison. The experimental results showed that improvements in the predictive accuracy and capacity for generalization can be achieved by the SVR_poly approach in comparison to the SVR_rbf methodology. The same testing errors were found for the SVR_poly approach and the ANFIS approach.

EPR Oximetry Sensor-Developing a TAM Derivative for In Vivo Studies.

PubMed

Boś-Liedke, Agnieszka; Walawender, Magdalena; Woźniak, Anna; Flak, Dorota; Gapiński, Jacek; Jurga, Stefan; Kucińska, Małgorzata; Plewiński, Adam; Murias, Marek; Elewa, Marwa; Lampp, Lisa; Imming, Peter; Tadyszak, Krzysztof

2018-06-01

Oxygenation is one of the most important physiological parameters of biological systems. Low oxygen concentration (hypoxia) is associated with various pathophysiological processes in different organs. Hypoxia is of special importance in tumor therapy, causing poor response to treatment. Triaryl methyl (TAM) derivative radicals are commonly used in electron paramagnetic resonance (EPR) as sensors for quantitative spatial tissue oxygen mapping. They are also known as magnetic resonance imaging (MRI) contrast agents and fluorescence imaging compounds. We report the properties of the TAM radical tris(2,3,5,6-tetrachloro-4-carboxy-phenyl)methyl, (PTMTC), a potential multimodal (EPR/fluorescence) marker. PTMTC was spectrally analyzed using EPR and characterized by estimation of its sensitivity to the oxygen in liquid environment suitable for intravenous injection (1 mM PBS, pH = 7.4). Further, fluorescent emission of the radical was measured using the same solvent and its quantum yield was estimated. An in vitro cytotoxicity examination was conducted in two cancer cell lines, HT-29 (colorectal adenocarcinoma) and FaDu (squamous cell carcinoma) and followed by uptake studies. The stability of the radical in different solutions (PBS pH = 7.4, cell media used for HT-29 and FaDu cells culturing and cytotoxicity procedure, full rat blood and blood plasma) was determined. Finally, a primary toxicity test of PTMTC was carried out in mice. Results of spectral studies confirmed the multimodal properties of PTMTC. PTMTC was demonstrated to be not absorbed by cancer cells and did not interfere with luciferin-luciferase based assays. Also in vitro and in vivo tests showed that it was non-toxic and can be freely administrated till doses of 250 mg/kg BW via both i.v. and i.p. injections. This work illustrated that PTMTC is a perfect candidate for multimodal (EPR/fluorescence) contrast agent in preclinical studies.

Versatile quantitative phase imaging system applied to high-speed, low noise and multimodal imaging (Conference Presentation)

NASA Astrophysics Data System (ADS)

Federici, Antoine; Aknoun, Sherazade; Savatier, Julien; Wattellier, Benoit F.

2017-02-01

Quadriwave lateral shearing interferometry (QWLSI) is a well-established quantitative phase imaging (QPI) technique based on the analysis of interference patterns of four diffraction orders by an optical grating set in front of an array detector [1]. As a QPI modality, this is a non-invasive imaging technique which allow to measure the optical path difference (OPD) of semi-transparent samples. We present a system enabling QWLSI with high-performance sCMOS cameras [2] and apply it to perform high-speed imaging, low noise as well as multimodal imaging. This modified QWLSI system contains a versatile optomechanical device which images the optical grating near the detector plane. Such a device is coupled with any kind of camera by varying its magnification. In this paper, we study the use of a sCMOS Zyla5.5 camera from Andor along with our modified QWLSI system. We will present high-speed live cell imaging, up to 200Hz frame rate, in order to follow intracellular fast motions while measuring the quantitative phase information. The structural and density information extracted from the OPD signal is complementary to the specific and localized fluorescence signal [2]. In addition, QPI detects cells even when the fluorophore is not expressed. This is very useful to follow a protein expression with time. The 10 µm spatial pixel resolution of our modified QWLSI associated to the high sensitivity of the Zyla5.5 enabling to perform high quality fluorescence imaging, we have carried out multimodal imaging revealing fine structures cells, like actin filaments, merged with the morphological information of the phase. References [1]. P. Bon, G. Maucort, B. Wattellier, and S. Monneret, "Quadriwave lateral shearing interferometry for quantitative phase microscopy of living cells," Opt. Express, vol. 17, pp. 13080-13094, 2009. [2] P. Bon, S. Lécart, E. Fort and S. Lévêque-Fort, "Fast label-free cytoskeletal network imaging in living mammalian cells," Biophysical journal, 106(8), pp. 1588-1595, 2014

Ultrasonic guided wave tomography of pipes: A development of new techniques for the nondestructive evaluation of cylindrical geometries and guided wave multi-mode analysis

NASA Astrophysics Data System (ADS)

Leonard, Kevin Raymond

This dissertation concentrates on the development of two new tomographic techniques that enable wide-area inspection of pipe-like structures. By envisioning a pipe as a plate wrapped around upon itself, the previous Lamb Wave Tomography (LWT) techniques are adapted to cylindrical structures. Helical Ultrasound Tomography (HUT) uses Lamb-like guided wave modes transmitted and received by two circumferential arrays in a single crosshole geometry. Meridional Ultrasound Tomography (MUT) creates the same crosshole geometry with a linear array of transducers along the axis of the cylinder. However, even though these new scanning geometries are similar to plates, additional complexities arise because they are cylindrical structures. First, because it is a single crosshole geometry, the wave vector coverage is poorer than in the full LWT system. Second, since waves can travel in both directions around the circumference of the pipe, modes can also constructively and destructively interfere with each other. These complexities necessitate improved signal processing algorithms to produce accurate and unambiguous tomographic reconstructions. Consequently, this work also describes a new algorithm for improving the extraction of multi-mode arrivals from guided wave signals. Previous work has relied solely on the first arriving mode for the time-of-flight measurements. In order to improve the LWT, HUT and MUT systems reconstructions, improved signal processing methods are needed to extract information about the arrival times of the later arriving modes. Because each mode has different through-thickness displacement values, they are sensitive to different types of flaws, and the information gained from the multi-mode analysis improves understanding of the structural integrity of the inspected material. Both tomographic frequency compounding and mode sorting algorithms are introduced. It is also shown that each of these methods improve the reconstructed images both qualitatively and quantitatively.

Multimodal Interfaces: Literature Review of Ecological Interface Design, Multimodal Perception and Attention, and Intelligent Adaptive Multimodal Interfaces

DTIC Science & Technology

2010-05-01

Multimodal Interfaces Literature Review of Ecological Interface Design , Multimodal Perception and Attention, and Intelligent... Design , Multimodal Perception and Attention, and Intelligent Adaptive Multimodal Interfaces Wayne Giang, Sathya Santhakumaran, Ehsan Masnavi, Doug...Advanced Interface Design Laboratory, E2-1303N 200 University Avenue West Waterloo, Ontario Canada N2L 3G1 Contract Project Manager: Dr. Catherine

Vacuum-Compatible Wideband White Light and Laser Combiner Source System

NASA Technical Reports Server (NTRS)

Azizi, Alineza; Ryan, Daniel J.; Tang, Hong; Demers, Richard T.; Kadogawa, Hiroshi; An, Xin; Sun, George Y.

2010-01-01

For the Space Interferometry Mission (SIM) Spectrum Calibration Development Unit (SCDU) testbed, wideband white light is used to simulate starlight. The white light source mount requires extremely stable pointing accuracy (<3.2 microradians). To meet this and other needs, the laser light from a single-mode fiber was combined, through a beam splitter window with special coating from broadband wavelengths, with light from multimode fiber. Both lights were coupled to a photonic crystal fiber (PCF). In many optical systems, simulating a point star with broadband spectrum with stability of microradians for white light interferometry is a challenge. In this case, the cameras use the white light interference to balance two optical paths, and to maintain close tracking. In order to coarse align the optical paths, a laser light is sent into the system to allow tracking of fringes because a narrow band laser has a great range of interference. The design requirements forced the innovators to use a new type of optical fiber, and to take a large amount of care in aligning the input sources. The testbed required better than 1% throughput, or enough output power on the lowest spectrum to be detectable by the CCD camera (6 nW at camera). The system needed to be vacuum-compatible and to have the capability for combining a visible laser light at any time for calibration purposes. The red laser is a commercially produced 635-nm laser 5-mW diode, and the white light source is a commercially produced tungsten halogen lamp that gives a broad spectrum of about 525 to 800 nm full width at half maximum (FWHM), with about 1.4 mW of power at 630 nm. A custom-made beam splitter window with special coating for broadband wavelengths is used with the white light input via a 50-mm multi-mode fiber. The large mode area PCF is an LMA-8 made by Crystal Fibre (core diameter of 8.5 mm, mode field diameter of 6 mm, and numerical aperture at 625 nm of 0.083). Any science interferometer that needs a tracking laser fringe to assist in alignment can use this system.

Educational Reforms and Inequalities in Israel: The MMI Hypothesis Revisited

ERIC Educational Resources Information Center

Ayalon, Hanna; Shavit, Yossi

2004-01-01

Israeli secondary school students sit for national matriculation examinations that result in their receiving either a plain or a university-qualifying diploma. During the 1990s, the Ministry of Education implemented policies that were designed to raise eligibility rates for the diploma. This article evaluates the consequences of these policies for…

Rater Perceptions of Bias Using the Multiple Mini-Interview Format: A Qualitative Study

ERIC Educational Resources Information Center

Alweis, Richard L.; Fitzpatrick, Caroline; Donato, Anthony A.

2015-01-01

Introduction: The Multiple Mini-Interview (MMI) format appears to mitigate individual rater biases. However, the format itself may introduce structural systematic bias, favoring extroverted personality types. This study aimed to gain a better understanding of these biases from the perspective of the interviewer. Methods: A sample of MMI…

Temperature-driven global sea-level variability in the Common Era.

PubMed

Kopp, Robert E; Kemp, Andrew C; Bittermann, Klaus; Horton, Benjamin P; Donnelly, Jeffrey P; Gehrels, W Roland; Hay, Carling C; Mitrovica, Jerry X; Morrow, Eric D; Rahmstorf, Stefan

2016-03-15

We assess the relationship between temperature and global sea-level (GSL) variability over the Common Era through a statistical metaanalysis of proxy relative sea-level reconstructions and tide-gauge data. GSL rose at 0.1 ± 0.1 mm/y (2σ) over 0-700 CE. A GSL fall of 0.2 ± 0.2 mm/y over 1000-1400 CE is associated with ∼ 0.2 °C global mean cooling. A significant GSL acceleration began in the 19th century and yielded a 20th century rise that is extremely likely (probability [Formula: see text]) faster than during any of the previous 27 centuries. A semiempirical model calibrated against the GSL reconstruction indicates that, in the absence of anthropogenic climate change, it is extremely likely ([Formula: see text]) that 20th century GSL would have risen by less than 51% of the observed [Formula: see text] cm. The new semiempirical model largely reconciles previous differences between semiempirical 21st century GSL projections and the process model-based projections summarized in the Intergovernmental Panel on Climate Change's Fifth Assessment Report.

Progress Toward Modeling Spectroscopic Signatures of Mix on Omega and NIF

NASA Astrophysics Data System (ADS)

Tregillis, I. L.; Schmitt, M. J.; Hsu, S. C.; Wysocki, F. J.; Cobble, J. A.; Murphy, T. J.

2011-10-01

Defect-induced mix processes may degrade the performance of ICF and ICF-like targets at Omega and NIF. An improved understanding of the relevant physics requires an experimental program built on a foundation of radiation-hydrodynamic simulations plus reliable synthetic diagnostic outputs. To that end, the Applications of Ignition (AoI) and Defect Implosion Experiment (DIME) efforts at LANL have focused on directly driven plastic capsules containing high-Z dopants and manufactured with an equatorial ``trench'' defect. One of the key diagnostic techniques for detecting and diagnosing the migration of dopant material into the hot core is Multi-Monochromatic X-ray Imaging (MMI). This talk will focus on recent efforts to model spectroscopic signatures of mix processes in AoI/DIME capsules via simulated MMI-type diagnostic instruments. It will also include data from recent Omega shots and calculations in support of Tier 1 experiments at NIF in FY2012. This work is supported by US DOE/NNSA, performed at LANL, operated by LANS LLC under contract DE-AC52-06NA25396.

Two Aspects of the Rural-Urban Divide and Educational Stratification in China: A Trajectory Analysis*

PubMed Central

Hao, Lingxin; Hu, Alfred; Lo, Jamie

2015-01-01

Contextualized in China’s social change of the past half-century, this paper develops the notion of dichotomous inequality to conceptualize the two aspects of China’s rural-urban divide in educational inequality—the household registration system (hukou) assigns people to a top-bottom hierarchy, and the rural-urban schooling system institutionalizes unequal resource distribution and diverse school mission. Based on this conceptualization, we formulate a Chinese version of the maximally maintained inequality (MMI) hypothesis. We capitalize on individual educational history data from the China General Social Survey (CGSS) 2008 and conduct a trajectory analysis using the generalized mixture modeling to estimate the differential effects of the two aspects of rural-urban divide on educational inequality in China. Findings indicate that (1) the sorting mechanism of the rural hukou places rural-hukou people in the very bottom of educational stratification, (2) the penalty of attending rural pre-tertiary school increases with educational stages, and (3) there is a cumulative disadvantage of rural hukou and rural school. Overall, our findings attest to the Chinese-version MMI and the behind principle of inequality reproduction. PMID:26166835

Geolocating thermal binoculars based on a software defined camera core incorporating HOT MCT grown by MOVPE

NASA Astrophysics Data System (ADS)

Pillans, Luke; Harmer, Jack; Edwards, Tim; Richardson, Lee

2016-05-01

Geolocation is the process of calculating a target position based on bearing and range relative to the known location of the observer. A high performance thermal imager with integrated geolocation functions is a powerful long range targeting device. Firefly is a software defined camera core incorporating a system-on-a-chip processor running the AndroidTM operating system. The processor has a range of industry standard serial interfaces which were used to interface to peripheral devices including a laser rangefinder and a digital magnetic compass. The core has built in Global Positioning System (GPS) which provides the third variable required for geolocation. The graphical capability of Firefly allowed flexibility in the design of the man-machine interface (MMI), so the finished system can give access to extensive functionality without appearing cumbersome or over-complicated to the user. This paper covers both the hardware and software design of the system, including how the camera core influenced the selection of peripheral hardware, and the MMI design process which incorporated user feedback at various stages.

Two Aspects of the Rural-Urban Divide and Educational Stratification in China: A Trajectory Analysis.

PubMed

Hao, Lingxin; Hu, Alfred; Lo, Jamie

2014-08-01

Contextualized in China's social change of the past half-century, this paper develops the notion of dichotomous inequality to conceptualize the two aspects of China's rural-urban divide in educational inequality-the household registration system ( hukou ) assigns people to a top-bottom hierarchy, and the rural-urban schooling system institutionalizes unequal resource distribution and diverse school mission. Based on this conceptualization, we formulate a Chinese version of the maximally maintained inequality (MMI) hypothesis. We capitalize on individual educational history data from the China General Social Survey (CGSS) 2008 and conduct a trajectory analysis using the generalized mixture modeling to estimate the differential effects of the two aspects of rural-urban divide on educational inequality in China. Findings indicate that (1) the sorting mechanism of the rural hukou places rural- hukou people in the very bottom of educational stratification, (2) the penalty of attending rural pre-tertiary school increases with educational stages, and (3) there is a cumulative disadvantage of rural hukou and rural school. Overall, our findings attest to the Chinese-version MMI and the behind principle of inequality reproduction.

Temperature-driven global sea-level variability in the Common Era

PubMed Central

Kopp, Robert E.; Kemp, Andrew C.; Bittermann, Klaus; Horton, Benjamin P.; Donnelly, Jeffrey P.; Gehrels, W. Roland; Hay, Carling C.; Mitrovica, Jerry X.; Morrow, Eric D.; Rahmstorf, Stefan

2016-01-01

We assess the relationship between temperature and global sea-level (GSL) variability over the Common Era through a statistical metaanalysis of proxy relative sea-level reconstructions and tide-gauge data. GSL rose at 0.1 ± 0.1 mm/y (2σ) over 0–700 CE. A GSL fall of 0.2 ± 0.2 mm/y over 1000–1400 CE is associated with ∼0.2 °C global mean cooling. A significant GSL acceleration began in the 19th century and yielded a 20th century rise that is extremely likely (probability P≥0.95) faster than during any of the previous 27 centuries. A semiempirical model calibrated against the GSL reconstruction indicates that, in the absence of anthropogenic climate change, it is extremely likely (P=0.95) that 20th century GSL would have risen by less than 51% of the observed 13.8±1.5 cm. The new semiempirical model largely reconciles previous differences between semiempirical 21st century GSL projections and the process model-based projections summarized in the Intergovernmental Panel on Climate Change’s Fifth Assessment Report. PMID:26903659

Water oxidation catalyzed by mononuclear ruthenium complexes with a 2,2'-bipyridine-6,6'-dicarboxylate (bda) ligand: how ligand environment influences the catalytic behavior.

PubMed

Staehle, Robert; Tong, Lianpeng; Wang, Lei; Duan, Lele; Fischer, Andreas; Ahlquist, Mårten S G; Sun, Licheng; Rau, Sven

2014-02-03

A new water oxidation catalyst [Ru(III)(bda)(mmi)(OH2)](CF3SO3) (2, H2bda = 2,2'-bipyridine-6,6'-dicarboxylic acid; mmi = 1,3-dimethylimidazolium-2-ylidene) containing an axial N-heterocyclic carbene ligand and one aqua ligand was synthesized and fully characterized. The kinetics of catalytic water oxidation by 2 were measured using stopped-flow technique, and key intermediates in the catalytic cycle were probed by density functional theory calculations. While analogous Ru-bda water oxidation catalysts [Ru(bda)L2] (L = pyridyl ligands) are supposed to catalyze water oxidation through a bimolecular coupling pathway, our study points out that 2, surprisingly, undergoes a single-site water nucleophilic attack (acid-base) pathway. The diversion of catalytic mechanisms is mainly ascribed to the different ligand environments, from nonaqua ligands to an aqua ligand. Findings in this work provide some critical proof for our previous hypothesis about how alternation of ancillary ligands of water oxidation catalysts influences their catalytic efficiency.

Sudden unexpected death owing to unilateral medial medullary infarction with early involvement of the respiratory center.

PubMed

Hata, Yukiko; Yoshida, Koji; Kinoshita, Koshi; Nishida, Naoki

2014-05-01

A 64-year-old woman was found dead in her home. At autopsy, although relatively fresh bruises were found on her body, no lethal injury was observed in an internal observation. Mild edematous swelling of the right half of the medulla oblongata was observed. There was acute medial medullary infarction (MMI), which mainly involved the nucleus hypoglossi, medial lemniscus, hypoglossal root, inferior olivary nucleus, and pyramidal tract. Subacute infarction of the lower part of the cerebellum was also found, and severe atherosclerosis of the right vertebral artery containing thrombi was found as the culprit lesion. Immunohistochemistry using amyloid precursor protein (APP) was positive in neuronal tissue in the nucleus ambiguus, despite not showing coagulative necrosis in the nucleus. Therefore, acute ischemic necrosis of the nucleus ambiguus, which is considered to be a component of the dorsal respiratory group, may be a significant finding for her expected death. Immunohistochemistry of APP may be useful for confirming the precise extent of acute ischemia in brain stem infarction, such as unilateral MMI. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Organic carbon accumulation in Brazilian mangal sediments

NASA Astrophysics Data System (ADS)

Sanders, Christian J.; Smoak, Joseph M.; Sanders, Luciana M.; Sathy Naidu, A.; Patchineelam, Sambasiva R.

2010-12-01

This study reviews the organic carbon (OC) accumulation rates in mangrove forests, margins and intertidal mudflats in geographically distinct areas along the Brazilian coastline (Northeastern to Southern). Our initial results indicate that the mangrove forests in the Northeastern region of Brazil are accumulating more OC (353 g/m 2/y) than in the Southeastern areas (192 g/m 2/y) being that the sediment accumulation rates, 2.8 and 2.5 mm/y, and OC content ˜7.1% and ˜5.8% (dry sediment weight) were contributing factors to the discrepancies between the forests. The intertidal mudflats on the other hand showed substantially greater OC accumulation rates, sedimentation rates and content 1129 g/m 2/y and 234 g/m 2/y; 7.3 and 3.4 mm/y; 10.3% and ˜2.7% (OC of dry sediment weight content), respectively, in the Northeastern compared to the Southeastern region. Mangrove forests in the South-Southeastern regions of Brazil may be more susceptible to the rising sea level, as they are geographically constricted by the vast mountain ranges along the coastline.

Pain patients' experiences of validation and invalidation from physicians before and after multimodal pain rehabilitation: Associations with pain, negative affectivity, and treatment outcome.

PubMed

Edlund, Sara M; Wurm, Matilda; Holländare, Fredrik; Linton, Steven J; Fruzzetti, Alan E; Tillfors, Maria

2017-10-01

Validating and invalidating responses play an important role in communication with pain patients, for example regarding emotion regulation and adherence to treatment. However, it is unclear how patients' perceptions of validation and invalidation relate to patient characteristics and treatment outcome. The aim of this study was to investigate the occurrence of subgroups based on pain patients' perceptions of validation and invalidation from their physicians. The stability of these perceptions and differences between subgroups regarding pain, pain interference, negative affectivity and treatment outcome were also explored. A total of 108 pain patients answered questionnaires regarding perceived validation and invalidation, pain severity, pain interference, and negative affectivity before and after pain rehabilitation treatment. Two cluster analyses using perceived validation and invalidation were performed, one on pre-scores and one on post-scores. The stability of patient perceptions from pre- to post-treatment was investigated, and clusters were compared on pain severity, pain interference, and negative affectivity. Finally, the connection between perceived validation and invalidation and treatment outcome was explored. Three clusters emerged both before and after treatment: (1) low validation and heightened invalidation, (2) moderate validation and invalidation, and (3) high validation and low invalidation. Perceptions of validation and invalidation were generally stable over time, although there were individuals whose perceptions changed. When compared to the other two clusters, the low validation/heightened invalidation cluster displayed significantly higher levels of pain interference and negative affectivity post-treatment but not pre-treatment. The whole sample significantly improved on pain interference and depression, but treatment outcome was independent of cluster. Unexpectedly, differences between clusters on pain interference and negative affectivity were only found post-treatment. This appeared to be due to the pre- and post-heightened invalidation clusters not containing the same individuals. Therefore, additional analyses were conducted to investigate the individuals who changed clusters. Results showed that patients scoring high on negative affectivity ended up in the heightened invalidation cluster post-treatment. Taken together, most patients felt understood when communicating with their rehabilitation physician. However, a smaller group of patients experienced the opposite: low levels of validation and heightened levels of invalidation. This group stood out as more problematic, reporting greater pain interference and negative affectivity when compared to the other groups after treatment. Patient perceptions were typically stable over time, but some individuals changed cluster, and these movements seemed to be related to negative affectivity and pain interference. These results do not support a connection between perceived validation and invalidation from physicians (meeting the patients pre- and post-treatment) and treatment outcome. Overall, our results suggest that there is a connection between negative affectivity and pain interference in the patients, and perceived validation and invalidation from the physicians. In clinical practice, it is important to pay attention to comorbid psychological problems and level of pain interference, since these factors may negatively influence effective communication. A focus on decreasing invalidating responses and/or increasing validating responses might be particularly important for patients with high levels of psychological problems and pain interference. Copyright © 2017. Published by Elsevier B.V.

Integration of micro-/nano-/quantum-scale photonic devices: scientific and technological considerations

NASA Astrophysics Data System (ADS)

Lee, El-Hang; Lee, Seung-Gol; O, Beom Hoan; Park, Se Geun

2004-08-01

Scientific and technological issues and considerations regarding the integration of miniaturized microphotonic devices, circuits and systems in micron, submicron, and quantum scale, are presented. First, we examine the issues regarding the miniaturization of photonic devices including the size effect, proximity effect, energy confinement effect, microcavity effect, optical and quantum interference effect, high field effect, nonlinear effect, noise effect, quantum optical effect, and chaotic effect. Secondly, we examine the issues regarding the interconnection including the optical alignment, minimizing the interconnection losses, and maintaining optical modes. Thirdly, we address the issues regarding the two-dimensional or three-dimensional integration either in a hybrid format or in a monolithic format between active devices and passive devices of varying functions. We find that the concept of optical printed circuit board (O-PCB) that we propose is highly attractive as a platform for micro/nano/quantum-scale photonic integration. We examine the technological issues to be addressed in the process of fabrication, characterization, and packaging for actual implementation of the miniaturization, interconnection and integration. Devices that we have used for our study include: mode conversion schemes, micro-ring and micro-racetrack resonator devices, multimode interference devices, lasers, vertical cavity surface emitting microlasers, and their arrays. Future prospects are also discussed.

Sea Level, Land Motion, and the Anomalous Tide at Churchill, Hudson Bay

NASA Astrophysics Data System (ADS)

Ray, R. D.

2015-12-01

The importance of the tide gauge at Churchill, Manitoba, cannot be overstated. It is the only permanently operating tide gauge in the central Canadian Arctic, and it sits on a prime spot for monitoring the mantle's rebound from the Laurentide ice loss. Yet interpretation of the sea-level time series at Churchill has long been problematic, going back even to early work by Gutenberg in the 1940s. The long-term relative sea-level rates are inconsistent: approximately -4, -19, -5 ± 1 mm/y for the periods 1940-1970, 1970-1990, 1990-2014 respectively. Annual mean high water (MHW) and mean low water (MLW) reflect these trends until around 1990, after which MLW leveled off and is now nearly unchanging. Slightly later, around 2000, the semidiurnal tides became very anomalous, with falling amplitudes and slightly increasing phase lags. The amplitude of M2 was approximately 154 cm before 2000; it dropped to about 146 cm by 2010 and reached an all-time low of 142 cm in 2014. Satellite altimeter estimates of the tide in this region, although challenging because of seasonal ice cover, show no comparable M2 changes, so the tidal changes must be localized to the near vicinity of the gauge (or to the gauge itself if caused by a malfunction). On the other hand, altimetry confirms the post-1992 Churchill measurements of mean sea level, thanks to the long time series of land motion measurements obtained at GPS station CHUR, which gives a vertical uplift of 10.1 mm/y. Combining satellite altimeter data with the Churchill tide-gauge data gives an implied vertical crustal rate of about 9.0 ± 0.8 mm/y, in reasonable agreement with the GPS. In summary, we have still anomalous MSL measurements at the Churchill gauge for the intermediate 1970-1990 era, and very anomalous tidal measurements since 2000, but we have apparently quite reliable MSL rates since 1990.

Antithyroid Drug Side Effects in the Population and in Pregnancy.

PubMed

Andersen, Stine Linding; Olsen, Jørn; Laurberg, Peter

2016-04-01

Methimazole (MMI) and propylthiouracil (PTU) are both associated with birth defects and may also rarely be associated with agranulocytosis and liver failure. The frequency of these side effects when antithyroid drugs (ATDs) are used in the population in general or in pregnancy remains to be elucidated. All individuals registered as the parent of a live-born child in Denmark, 1973–2008, were identified (n = 2 299 952) and studied from 1995 through 2010 for the use of ATDs. Outcomes were agranulocytosis, liver failure, and birth defects in their offspring. To evaluate the frequency of these side effects associated with the use of ATDs in pregnancy, all live-born pregnancies (n = 830 680), 1996–2008, were identified in a subanalysis. In the population studied, 28 998 individuals redeemed prescriptions of ATDs (exposure in 2115 pregnancies), which was associated with 45 cases of agranulocytosis (one in pregnancy) and 10 cases of liver failure (one in pregnancy). This corresponded to 41 and 11 cases of agranulocytosis and liver failure per 5 million inhabitants during a 10-year period (agranulocytosis: 0.16% of ATDs exposed [MMI: 0.11% vs PTU: 0.27%, P = .02]; liver failure: 0.03% of ATDs exposed [MMI: 0.03% vs PTU: 0.05%, P = .4]). The majority (83%) developed the side effect within 3 months of ATD treatment and 25% during hyperthyroidism relapse. The use of ATDs in pregnancy was associated with birth defects in 3.4% of exposed children (44 cases per 5 million inhabitants per 10 y), and the frequency of birth defects after ATD exposure was 75 times higher than both maternal agranulocytosis and liver failure in pregnancy. In the Danish population in general, ATDs associated birth defects and agranulocytosis had similar frequencies and were more common than liver failure, whereas for the use of ATDs in pregnancy, birth defects were dominant. The burden of side effects to the use of ATDs can be reduced by restricting the use of ATDs in early pregnancy.

Trends in anecdotal fox sightings in Tasmania accounted for by psychological factors.

PubMed

Marks, Clive A; Clark, Malcolm; Obendorf, David; Hall, Graham P; Soares, Inês; Pereira, Filipe

2017-12-01

There has been little evaluation of anecdotal sightings as a means to confirm new incursions of invasive species. This paper explores the potential for equivocal information communicated by the media to account for patterns of anecdotal reports. In 2001, it was widely reported that red foxes (Vulpes vulpes) had been deliberately released in the island state of Tasmania (Australia), although this claim was later revealed to be baseless. Regardless, by 2013 a total of 3153 anecdotal fox sightings had been reported by members of the public, which implied their distribution was wide. For each month in 2001-2003, we defined a monthly media index (MMI) of fox-related media coverage, an index of their relative seasonal abundance (abundance), and a factor denoting claims of fox evidence (claimed evidence) regardless of its evidentiary quality. We fitted a generalized linear model with Poisson error for monthly totals of anecdotal sightings with factors of year and claimed evidence and covariates of MMI, abundance, and hours of darkness. The collective effect of psychological factors (MMI, claimed evidence, and year) relative to biophysical factors (photoperiod and abundance) was highly significant (χ 2 = 122.1, df = 6, p < 0.0001), whereas anticipated changes in abundance had no significant influence on reported sightings (p = 0.15). An annual index of fox media from 2001 to 2010 was strongly associated with the yearly tally of anecdotal sightings (p = 0.018). The odds ratio of sightings ranked as reliable by the fox eradication program in any year decreased exponentially at a rate of 0.00643 as the total number of sightings increased (p < 0.0001) and was indicative of an observer-expectancy bias. Our results suggest anecdotal sightings are highly susceptible to cognitive biases and when used to qualify and quantify species presence can contribute to flawed risk assessments. © 2017 Society for Conservation Biology.