Science.gov

Sample records for multiphase system columns

  1. Multiphase fluid characterization system

    SciTech Connect

    Sinha, Dipen N.

    2014-09-02

    A measurement system and method for permitting multiple independent measurements of several physical parameters of multiphase fluids flowing through pipes are described. Multiple acoustic transducers are placed in acoustic communication with or attached to the outside surface of a section of existing spool (metal pipe), typically less than 3 feet in length, for noninvasive measurements. Sound speed, sound attenuation, fluid density, fluid flow, container wall resonance characteristics, and Doppler measurements for gas volume fraction may be measured simultaneously by the system. Temperature measurements are made using a temperature sensor for oil-cut correction.

  2. Modelling of multiphase flow in evaporation tests in concrete columns

    NASA Astrophysics Data System (ADS)

    Chaparro, M. Carme; Saaltink, Maarten W.; Villar, M. Victoria

    2013-04-01

    In order to characterize better the thermo-hydraulic properties and processes in concrete from a Radioactive Waste Disposal Facility at El Cabril (Spain), evaporation tests in columns have been analysed by means of numerical models. The tests consisted of letting water evaporate from the top of the column while monitoring water loss by weighing the column, and monitoring temperature and relative humidity by means of sensors placed within the column. Both non-isothermal (by heating the column with a lamp) and isothermal tests (without heating) were performed. The conceptual model considers unsaturated liquid flow and transport of vapour and heat. Some models also take into account the salinity in order to study its effect on vapour pressure and evaporation. A retention curve has been obtained from relative humidity and gravimetric water content measured after dismantling the columns. The models have been calibrated by fitting permeability and a tortuosity factor for vapour diffusion to the measured water loss, relative humidity and (in the case of the non-isothermal test) temperature. Results show that vapour diffusion is dominant above an evaporation front, and liquid advection is the dominant water transport process underneath this front. The salinity slightly reduces the evaporation with a factor of at most 5%. The tortuosity factor estimated from the isothermal test is lower than that of the non-isothermal test. This can be explained by the evaporation and condensation together with the heat transport that take place at pore scale under non-isothermal conditions, which are not taken into account by the model.

  3. Multiphase railgun systems - A new concept

    NASA Astrophysics Data System (ADS)

    Murthy, S. K.; Weldon, W. F.

    1993-01-01

    This paper investigates multiphase railguns powered by multiphase compulsators. The polyphase system offers several advantages over the single phase system. The multiphase compulsator relaxes the strong dependence between the current pulse width necessary for the railgun and the design parameters of the generator (number or poles, rotor diameter, and tip speed) thus allowing the compulsator to be designed for optimum power density and electromechanical energy conversion. The paper examines in particular the two, three and six phase systems. The authors also explore different methods of achieving high acceleration ratios in multiphase railgun systems. Some of the methods analyzed are ramping up the field current of the compulsator to counter the back electromotive force of the gun, utilizing a railgun with varying inductance per unit length (L'), and using an external variable inductor in series with the compulsator. The different features of each method are highlighted using simulation results. Special attention is devoted to the external series inductor method which uses a rotary flux compressor. Simulation results indicate an encouraging acceleration ratio of 0.7 for a muzzle energy of 9 MJ. A disk configuration is envisioned for the flux compressor.

  4. A Course in Transport Phenomena in Multicomponent, Multiphase, Reacting Systems.

    ERIC Educational Resources Information Center

    Carbonell, R. G.; Whitaker, S.

    1978-01-01

    This course concentrates on a rigorous development of the multicomponent transport equations, boundary conditions at phase interfaces, and volume-averaged transport equations for multiphase reacting systems. (BB)

  5. Multiphase Systems for Medical Image Region Classification

    NASA Astrophysics Data System (ADS)

    Garamendi, J. F.; Malpica, N.; Schiavi, E.

    2009-05-01

    Variational methods for region classification have shown very promising results in medical image analysis. The Chan-Vese model is one of the most popular methods, but its numerical resolution is slow and it has serious drawbacks for most multiphase applications. In this work, we extend the link, stablished by Chambolle, between the two classes binary Chan-Vese model and the Rudin-Osher-Fatemi (ROF) model to a multiphase four classes minimal partition problem. We solve the ROF image restoration model and then we threshold the image by means of a genetic algorithm. This strategy allows for a more efficient algorithm due to the fact that only one well posed elliptic problem is solved instead of solving the coupled parabolic equations arising in the original multiphase Chan-Vese model.

  6. Incorporation of Reaction Kinetics into a Multiphase, Hydrodynamic Model of a Fischer Tropsch Slurry Bubble Column Reactor

    SciTech Connect

    Donna Guillen, PhD; Anastasia Gribik; Daniel Ginosar, PhD; Steven P. Antal, PhD

    2008-11-01

    This paper describes the development of a computational multiphase fluid dynamics (CMFD) model of the Fischer Tropsch (FT) process in a Slurry Bubble Column Reactor (SBCR). The CMFD model is fundamentally based which allows it to be applied to different industrial processes and reactor geometries. The NPHASE CMFD solver [1] is used as the robust computational platform. Results from the CMFD model include gas distribution, species concentration profiles, and local temperatures within the SBCR. This type of model can provide valuable information for process design, operations and troubleshooting of FT plants. An ensemble-averaged, turbulent, multi-fluid solution algorithm for the multiphase, reacting flow with heat transfer was employed. Mechanistic models applicable to churn turbulent flow have been developed to provide a fundamentally based closure set for the equations. In this four-field model formulation, two of the fields are used to track the gas phase (i.e., small spherical and large slug/cap bubbles), and the other two fields are used for the liquid and catalyst particles. Reaction kinetics for a cobalt catalyst is based upon values reported in the published literature. An initial, reaction kinetics model has been developed and exercised to demonstrate viability of the overall solution scheme. The model will continue to be developed with improved physics added in stages.

  7. DEVELOPMENT OF A COMPUTATIONAL MULTIPHASE FLOW MODEL FOR FISCHER TROPSCH SYNTHESIS IN A SLURRY BUBBLE COLUMN REACTOR

    SciTech Connect

    Donna Post Guillen; Tami Grimmett; Anastasia M. Gribik; Steven P. Antal

    2010-09-01

    The Hybrid Energy Systems Testing (HYTEST) Laboratory is being established at the Idaho National Laboratory to develop and test hybrid energy systems with the principal objective to safeguard U.S. Energy Security by reducing dependence on foreign petroleum. A central component of the HYTEST is the slurry bubble column reactor (SBCR) in which the gas-to-liquid reactions will be performed to synthesize transportation fuels using the Fischer Tropsch (FT) process. SBCRs are cylindrical vessels in which gaseous reactants (for example, synthesis gas or syngas) is sparged into a slurry of liquid reaction products and finely dispersed catalyst particles. The catalyst particles are suspended in the slurry by the rising gas bubbles and serve to promote the chemical reaction that converts syngas to a spectrum of longer chain hydrocarbon products, which can be upgraded to gasoline, diesel or jet fuel. These SBCRs operate in the churn-turbulent flow regime which is characterized by complex hydrodynamics, coupled with reacting flow chemistry and heat transfer, that effect reactor performance. The purpose of this work is to develop a computational multiphase fluid dynamic (CMFD) model to aid in understanding the physico-chemical processes occurring in the SBCR. Our team is developing a robust methodology to couple reaction kinetics and mass transfer into a four-field model (consisting of the bulk liquid, small bubbles, large bubbles and solid catalyst particles) that includes twelve species: (1) CO reactant, (2) H2 reactant, (3) hydrocarbon product, and (4) H2O product in small bubbles, large bubbles, and the bulk fluid. Properties of the hydrocarbon product were specified by vapor liquid equilibrium calculations. The absorption and kinetic models, specifically changes in species concentrations, have been incorporated into the mass continuity equation. The reaction rate is determined based on the macrokinetic model for a cobalt catalyst developed by Yates and Satterfield [1]. The

  8. System for measuring multiphase flow using multiple pressure differentials

    DOEpatents

    Fincke, James R.

    2003-01-01

    An improved method and system for measuring a multi-phase flow in a pressure flow meter. An extended throat venturi is used and pressure of the multi-phase flow is measured at three or more positions in the venturi, which define two or more pressure differentials in the flow conduit. The differential pressures are then used to calculate the mass flow of the gas phase, the total mass flow, and the liquid phase. The system for determining the mass flow of the high void fraction fluid flow and the gas flow includes taking into account a pressure drop experienced by the gas phase due to work performed by the gas phase in accelerating the liquid phase.

  9. Multiphase patterns in periodically forced oscillatory systems

    SciTech Connect

    Elphick, C.; Hagberg, A.; Meron, E.

    1999-05-01

    Periodic forcing of an oscillatory system produces frequency locking bands within which the system frequency is rationally related to the forcing frequency. We study extended oscillatory systems that respond to uniform periodic forcing at one quarter of the forcing frequency (the 4:1 resonance). These systems possess four coexisting stable states, corresponding to uniform oscillations with successive phase shifts of {pi}/2. Using an amplitude equation approach near a Hopf bifurcation to uniform oscillations, we study front solutions connecting different phase states. These solutions divide into two groups: {pi} fronts separating states with a phase shift of {pi} and {pi}/2 fronts separating states with a phase shift of {pi}/2. We find a type of front instability where a stationary {pi} front {open_quotes}decomposes{close_quotes} into a pair of traveling {pi}/2 fronts as the forcing strength is decreased. The instability is degenerate for an amplitude equation with cubic nonlinearities. At the instability point a continuous family of pair solutions exists, consisting of {pi}/2 fronts separated by distances ranging from zero to infinity. Quintic nonlinearities lift the degeneracy at the instability point but do not change the basic nature of the instability. We conjecture the existence of similar instabilities in higher 2n:1 resonances (n=3,4,{hor_ellipsis}) where stationary {pi} fronts decompose into {ital n} traveling {pi}/n fronts. The instabilities designate transitions from stationary two-phase patterns to traveling 2n-phase patterns. As an example, we demonstrate with a numerical solution the collapse of a four-phase spiral wave into a stationary two-phase pattern as the forcing strength within the 4:1 resonance is increased. {copyright} {ital 1999} {ital The American Physical Society}

  10. Kinetic faceting and anomalous coarsening in elastically inhomogeneous multiphase systems.

    PubMed

    Perez, Danny; Lewis, Laurent J

    2007-02-16

    With a view of finding a route toward microstructural stability in alloys, we numerically study the impact of elastic inhomogeneities on the growth of inclusions in multiphase systems. We show that growth can proceed either continuously at rough interfaces, or in a layer-by-layer fashion following an elastically induced kinetic faceting process. In the former case, the chemical potential of the inclusions is a smooth function of size, while in the latter case, elasticity increases the barrier for nucleation of new terraces on the facets, leading to an oscillatory behavior of the chemical potential and hence a strong resistance against coarsening, opening up the possibility to stabilize the structure.

  11. Multiphase Carbon-14 Transport in a Near-Field-Scale Unsaturated Column of Natural Sediments

    SciTech Connect

    D. T. Fox; Mitchell A. Plummer; Larry C. Hull; D. Craig Cooper

    2004-03-01

    Wastes buried at the Subsurface Disposal Area (SDA) of the Idaho National Engineering and Environmental Laboratory include activated metals that release radioactive carbon-14 (14C) as they corrode. To better understand 14C phase partitioning and transport in the SDA sediments, we conducted a series of transport experiments using 14C (radio-labeled sodium carbonate) and nonreactive gas (sulfur hexafluoride) and aqueous (bromide and tritiated water) tracers in a large (2.6-m high by 0.9-m diameter) column of sediments similar to those used as cover material at the SDA. We established steady-state unsaturated flow prior to injecting tracers into the column. Tracer migration was monitored using pore-water and pore-gas samples taken from co-located suction lysimeters and gas ports inserted at ~0.3-m intervals along the column’s length. Measurements of 14C discharged from the sediment to the atmosphere (i.e., 14CO2 flux) indicate a positive correlation between CO2 partial pressure (pCO2) in the column and changes in 14CO2 flux. Though 14CO2 diffusion is expected to be independent of pCO2, changes of pCO2 affect pore water chemistry sufficiently to affect aqueous/gas phase 14C partitioning and consequently 14C2 flux. Pore-water and -gas 14C activity measurements provide an average aqueous/gas partitioning ratio, Kag, of 4.5 (±0.3). This value is consistent with that calculated using standard carbonate equilibrium expressions with measured pH, suggesting the ability to estimate Kag from carbonate equilibrium. One year after the 14C injection, the column was cored and solid-phase 14C activity was measured. The average aqueous/solid partition coefficient, Kd, (1.6 L kg-1) was consistent with those derived from small-scale and short-term batch and column experiments using SDA sediments, suggesting that bench-scale measurements are a valid means of estimating aqueous/solid partitioning at the much larger spatial scale considered in these meso-scale experiments. However

  12. Soil pollution by petroleum products, I. Multiphase migration of kerosene components in soil columns

    NASA Astrophysics Data System (ADS)

    Acher, A. J.; Boderie, P.; Yaron, B.

    1989-09-01

    A laboratory study of soil contamination by a synthetic "kerosene" is reported. Soil (Mediterranean red sandy clay) samples with different moisture contents (0.0, 0.8, 4.0, and 12%, w/w) were contaminated by vapors and/or liquid from a mixture containing 5 kerosene components (m-xylene, pseudo-cumene, t-butylbenzene, n-decane and n-dodecane). The contribution of the different kerosene components to the adsorption, volatilization and transport processes is described. Vapor adsorption was found to be dependent on the vapor concentration of each component (except for the n-decane), and on the soil moisture content. The sorption coefficients of the kerosene components decreased with increasing temperature but showed only a very slight variability between 20 and 34°C, in air-dried soil. The volatilization from soil was high: more than 90% of the aromatic components were desorbed in less than 2 h. The transport of the kerosene, in liquid and vapor phases, through the soil columns, was studied using amounts of kerosene which were less (1 mL) or more (10 mL) than the retention capacity of the soil columns. The increase in the moisture content of the soil increased the rate and the depth of kerosene downward penetration. It stopped however, the vapor movement (at 4%) and the upward liquid movement (at 12%). Among the properties of the kerosene components, volatility seems to be the prime factor which determines kerosene movement once liquid phase movement has ceased.

  13. Multi-phase galaxy formation and quasar absorption systems

    NASA Astrophysics Data System (ADS)

    Maller, Ariyeh H.

    2005-03-01

    The central problem of galaxy formation is understanding the cooling and condensation of gas in dark matter halos. It is now clear that to match observations this requires further physics than the simple assumptions of single phase gas cooling. A model of multi-phase cooling (maller & bullock 2004) can successfully account for the upper cutoff in the masses of galaxies and provides a natural explanation of many types of absorption systems (mo & miralda-escude 1996). Absorption systems are our best probes of the gaseous content of galaxy halos and therefore provide important constraints on models for gas cooling into galaxies. All physical processes that effect gas cooling redistribute gas and therefore are detectable in absorption systems. Detailed studies of the nature of gas in galaxy halos using absorption systems are crucial for building a correct theory of galaxy formation.

  14. The jet flotation column control system

    SciTech Connect

    Xu Zhiqiang; Ming Shangzhi; Liu Lijian; Huangfu Jinghua; Huo Sen; Zhang Rongzeng; Yang Hongjun

    1998-12-31

    Compared with the conventional mechanical flotation column, the jet flotation column has the advantages of high selectivity of separation, low investment and production cost, low floor space requirement, low dosage of reagent, easy control; it is more suitable to process fine particles. Recently, many new types of flotation columns have been developed with new methods. Mineral Processing Dept., China University of Mining and Technology (Beijing) designed an aerated, double-jet flotation column in the lab and the industrial trial will be put into operation. One of the significant characteristics of the new type of flotation column is high selectivity of separation, fast bubble mineralization speed. As it is sensitive to various factors, a control system for flotation column has been developed to stabilize the working condition, and this set of control system has been operated in the lab experiment.

  15. Multiphase Flow Technology Impacts on Thermal Control Systems for Exploration

    NASA Technical Reports Server (NTRS)

    McQuillen, John; Sankovic, John; Lekan, Jack

    2006-01-01

    The Two-Phase Flow Facility (TPHIFFy) Project focused on bridging the critical knowledge gap by developing and demonstrating critical multiphase fluid products for advanced life support, thermal management and power conversion systems that are required to enable the Vision for Space Exploration. Safety and reliability of future systems will be enhanced by addressing critical microgravity fluid physics issues associated with flow boiling, condensation, phase separation, and system stability. The project included concept development, normal gravity testing, and reduced gravity aircraft flight campaigns, in preparation for the development of a space flight experiment implementation. Data will be utilized to develop predictive models that could be used for system design and operation. A single fluid, two-phase closed thermodynamic loop test bed was designed, assembled and tested. The major components in this test bed include: a boiler, a condenser, a phase separator and a circulating pump. The test loop was instrumented with flow meters, thermocouples, pressure transducers and both high speed and normal speed video cameras. A low boiling point surrogate fluid, FC-72, was selected based on scaling analyses using preliminary designs for operational systems. Preliminary results are presented which include flow regime transitions and some observations regarding system stability.

  16. Design and Development of Integrated Compact Multiphase Separation System (CMSS)

    SciTech Connect

    Ram S. Mohan; Ovadia Shoham

    2006-04-30

    The petroleum industry has relied in the past mainly on conventional vessel-type separators, which are bulky, heavy and expensive, to process wellhead production of oil-water-gas flow. Economic and operational pressures continue to force the petroleum industry to seek less expensive and more efficient separation alternatives in the form of compact separators. The compact dimensions, smaller footprint and lower weight of compact separators have a potential for cost savings to the industry, especially in offshore and subsea applications. Also, compact separators reduce the inventory of hydrocarbons significantly, which is critical for environmental This report presents a brief overview of the activities and tasks accomplished during the Budget Period II (October 09, 2004-April 30, 2006) of the DOE project titled ''Design and Development of Integrated Compact Multiphase Separation System (CMSS{copyright})''. An executive summary is presented initially followed by the tasks of the current budget period. Then, detailed description of the experimental and modeling investigations are presented. Subsequently, the technical and scientific results of the activities of this project period are presented with discussions. The findings of this investigation are summarized in the ''Conclusions'' section In this investigation, the concept of CMSS{copyright} has been developed and is proven through simulation studies and validated by experimental data. As part of the second phase of the project (Budget Period II--10/09/2004-04/30/2006) experimental investigation of the integrated CMSS{copyright} for different configurations has been conducted in order to evaluate the performance of the individual separation components, and determine how they will affect the performance of each other when integrated in the CMSS{copyright}. An intelligent control system is also developed to improve the total system efficiency of Compact Multiphase Separation System (CMSS{copyright}). In mature oil

  17. Compositional space parameterization for general multi-component multiphase systems

    NASA Astrophysics Data System (ADS)

    Voskov, Denis; Tchelepi, Hamdi

    2007-11-01

    We present a general parameterization of the thermodynamic behavior of multiphase, multi-component systems. The phase behavior in the compositional space is represented using a low dimensional tie-simplex parameterization. This parameterization improves the robustness of the phase behavior representation as well as the efficiency of various types of compositional computations. We demonstrate this Compositional Space Parameterization (CSP) framework for large-scale compositional reservoir simulation. In the standard compositional simulation approach, an Equation of State (EoS) is used to detect the phase state and calculate the phase compositions, if needed. These EoS computations can dominate the overall simulation cost. We compare our adaptive CSP approach with standard EoS based simulation for several challenging problems of practical interest. The comparisons indicate that the CSP strategy is more robust, and computational efficient. Another type of applications is an equilibrium flash calculation of systems with a large number of phases. The complexity and strong nonlinear behaviors associated with such problems pose serious difficulties for standard techniques. Here, we describe an effective tie-simplex parameterization for such systems at a fixed pressure and temperature. The preprocessed data can be used in conventional EoS based calculations as an initial guess to accelerate convergence.

  18. Multiphase flow modeling based on the hyperbolic thermodynamically compatible systems theory

    SciTech Connect

    Romenski, E.

    2015-03-10

    An application of the theory of thermodynamically compatible hyperbolic systems to design a multiphase compressible flow models is discussed. With the use of such approach the governing equations are derived from the first principles, formulated in a divergent form and can be transformed to a symmetric hyperbolic system in the sense of Friedrichs. A usage of the proposed approach is described for the development of multiphase compressible fluid models, including two-phase flow models.

  19. Multiphase flow calculation software

    DOEpatents

    Fincke, James R.

    2003-04-15

    Multiphase flow calculation software and computer-readable media carrying computer executable instructions for calculating liquid and gas phase mass flow rates of high void fraction multiphase flows. The multiphase flow calculation software employs various given, or experimentally determined, parameters in conjunction with a plurality of pressure differentials of a multiphase flow, preferably supplied by a differential pressure flowmeter or the like, to determine liquid and gas phase mass flow rates of the high void fraction multiphase flows. Embodiments of the multiphase flow calculation software are suitable for use in a variety of applications, including real-time management and control of an object system.

  20. Axisymmetric Column Collapse in a Rotating System

    NASA Astrophysics Data System (ADS)

    Warnett, Jay; Thomas, Peter; Dennisenko, Petr

    2012-11-01

    We discuss experimental and computational results of a study investigating the collapse of an initially axisymmetric cylindrical column of granular material within a rotating environment of air or liquids. In industry this type of granular column collapse that is subject to background rotation is encountered, for instance, in the context of the spreading of powders and fertilizers. In comparison to its non-rotating counterpart the physical characteristics of the column collapse in a rotating system are expected to be modified by effects arising from centrifugal forces and Coriolis forces. We compare our new results for the rotating flow to data available in the literature for the collapse of granular columns in non-rotating systems to highlight the differences observed.

  1. Multiphase production systems R and D state of the art

    SciTech Connect

    Bratu, C.

    1996-12-31

    Studies and developments concerning multiphase production prompted a significant effort in R and D areas of pipeline flow behavior, pumps, instrumentation and fluids process (hydrates and paraffin deposition). Multiphase flow in pipelines network in steady and transient conditions is still a basic goal; experimental correlations and computer codes are now in validation phase using field data banks. Multiphase pumps groups development reaches the industrial phase; the rotodynamic pump (Poseidon) and the volumetric twin-screw booster (Novopignone, Bornemann) prototypes were recently tested on actual fields. Dedicated to measure mixture flow rates, the instrumentation is still an uneven development. A lot of instruments are commercially ready, but their accuracy, stability, intrusive character or operational difficulties delay extensive field application. An important feature is related to the process of complex fluids in operational conditions that involves hydrates and paraffin deposit formation. Studies and experimental approach are focused on physico-chemical mechanism of deposit build-up pipeline multiphase flow configurations (including solid phase) and additives (dispersants, kinetic or combined).

  2. DESIGN AND DEVELOPMENT OF INTEGRATED COMPACT MULTIPHASE SEPARATION SYSTEM (CMSS)

    SciTech Connect

    Ram S. Mohan; Ovadia Shoham

    2004-12-31

    The petroleum industry has relied in the past mainly on conventional vessel-type separators, which are bulky, heavy and expensive, to process wellhead production of oil-water-gas flow. Economic and operational pressures continue to force the petroleum industry to seek less expensive and more efficient separation alternatives in the form of compact separators. The compact dimensions, smaller footprint and lower weight of compact separators have a potential for cost savings to the industry, especially in offshore and subsea applications. Also, compact separators reduce the inventory of hydrocarbons significantly, which is critical for environmental and safety considerations. This report presents a brief overview of the activities and tasks accomplished during the part July 09, 2003--October 08, 2004, related to the Budget Period I (July 09, 2003--October 08, 2004) of the DOE project titled ''Design and Development of Integrated Compact Multiphase Separation System (CMSS{copyright})''. An executive summary is presented initially followed by the tasks of the current budget period. Then, detailed description of the experimental and modeling investigations are presented. Subsequently, the technical and scientific results of the activities of this project period are presented with discussions. The findings of this investigation are summarized in the ''Conclusions'' section followed by relevant references. The initial phase of the project (Budget Period I--07/09/2003 to 10/08/2004) focuses on the development of additional individual compact separation components, such as the horizontal pipe separator (HPS{copyright}), for obtaining clean oil stream from oil-water mixture, flow conditioning components, such as the helical pipe (HP) and slug damper (SD{copyright}), for dissipating slugs upstream of the compact separators. The project will also design and test an upstream slug generator (SG).

  3. Investigation of hydrate formation and transportability in multiphase flow systems

    NASA Astrophysics Data System (ADS)

    Grasso, Giovanny A.

    The oil and gas industry is moving towards offshore developments in more challenging environments, where evaluating hydrate plugging risks to avoid operational/safety hazards becomes more difficult (Sloan, 2005). Even though mechanistic models for hydrate plug formation have been developed, components for a full comprehensive model are still missing. Prior to this work, research efforts were focused on flowing hydrate particles with relatively little research on hydrate accumulation, leaving hydrate deposition in multiphase flow an unexplored subject. The focus of this thesis was to better understand hydrate deposition as a form of accumu- lation in pipelines. To incorporate the multiphase flow effect, hydrate formation experiments were carried out at varying water cut (WC) from 15 to 100 vol.%, liquid loading (LL) from 50 to 85 vol.%, mixture velocity (vmix) from 0.75 to 3 m/s, for three fluids systems (100 % WC, water in Conroe crude oil emulsions and King Ranch condensate + water) on the ExxonMobil flowloop (4 in. nominal size and 314 ft. long) at Friendswood, TX. For the 100 % WC flowloop tests, hydrate particle distribution transitions beyond a critical hydrate volume concentration, observed values were between 8.2 to 29.4 vol.%, causing a sudden increase in pressure drop (DP). A revised correlation of the transition as a function of Reynolds number and liquid loading was developed. For Conroe emulsions, DP starts increasing at higher hydrate concentrations than King Ranch condensate, many times at 10 vol.%. Experiments with King Ranch show higher relative DP (10 to 25) than Conroe (2 to 10) performed at the same vmix and LL. Cohesive force measurements between cyclopentane hydrate particles were reduced from a value of 3.32 mN/m to 1.26 mN/m when 6 wt.% Conroe was used and to 0.41 mN/m when 5 wt.% Caratinga crude oil was used; similar values were obtained when extracted asphaltenes were used. King Ranch condensate (11 wt.%) did not significantly change the

  4. CUB DI (Deionization) column control system

    SciTech Connect

    K. C. Seino

    1999-07-02

    For the old MR (Main Ring), deionization was done with two columns in CUB, using an ion exchange process. Typically 65 GPM of LCW flew through a column, and the resistivity was raised from 3 Mohm-cm to over 12 Mohm-cm. After a few weeks, columns lost their effectiveness and had to be regenerated in a process involving backwashing and adding hydrochloric acid and sodium hydroxide. For normal MR operations, LCW returned from the ring and passed through the two columns in parallel for deionization, although the system could have been operated satisfactorily with only one in use. A 3000 gallon reservoir (the Spheres) provided a reserve of LCW for allowing water leaks and expansions in the MR. During the MI (Main Injector) construction period, the third DI column was added to satisfy requirements for the MI. When the third column was added, the old regeneration controller was replaced with a new controller based on an Allen-Bradley PLC (i.e., SLC-5/04). The PLC is widely used and well documented, and therefore it may allow us to modify the regeneration programs in the future. In addition to the above regeneration controller, the old control panels (which were used to manipulate pumps and valves to supply LCW in Normal mode and to do Int. Recir. (Internal Recirculation) and Makeup) were replaced with a new control system based on Sixtrak Gateway and I/O modules. For simplicity, the new regeneration controller is called as the US Filter system, and the new control system is called as the Fermilab system in this writing.

  5. Nanoparticle additives for multiphase systems: Synthesis, formulation and characterization

    NASA Astrophysics Data System (ADS)

    Kanniah, Vinod

    Study on nanoparticle additives in multiphase systems (liquid, polymer) are of immense interest in developing new product applications. Critical challenges for nanoparticle additives include their synthesis, formulation and characterization. These challenges are addressed in three application areas: nanofluids for engine lubrication, ultrathin nanocomposites for optical devices, and nanoparticle size distribution characterization. Nanoparticle additives in oligomer mixtures can be used to develop extended temperature range motor oils. A model system includes poly(alpha-olefin) based oligomers with a modest fraction of poly(dimethylsiloxane) oligomers along with graphite as nanoparticle additive. Partition coefficients of each oligomer are determined since the oligomer mixture phase separated at temperatures less than -15 °C. Also, the surface of graphite additive is quantitatively analyzed and modified via silanization for each oligomer. Thus, upon separation of the oligomer mixture, each functionalized graphite additive migrates to its preferred oligomers and forms a uniform dispersion. Similarly, nanoparticle additives in polymer matrices can be used to develop new low haze ultrathin film optical coatings. A model system included an acrylate monomer as the continuous phase with monodisperse or bidisperse mixtures of silica nanoparticles deposited on glass and polycarbonate substrates. Surface (root mean squared roughness, Wenzel's contact angle) and optical properties (haze) of these self assembled experimental surfaces were compared to simulated surface structures. Manipulating the size ratios of silica nanoparticle mixtures varied the average surface roughness and the height distributions, producing multimodal structures with different packing fractions. In both nanofluid and nanocomposite applications, nanoparticle additives tend to aggregate/agglomerate depending on various factors including the state of nanoparticles (powder, dispersion). A set of well

  6. The Multiphase Absorption Systems toward PG 1206+459

    NASA Astrophysics Data System (ADS)

    Ding, Jie; Charlton, Jane C.; Churchill, Christopher W.; Palma, Christopher

    2003-06-01

    A high-resolution (R=30,000) ultraviolet spectrum is presented, which covers Lyα and many low-, intermediate-, and high-ionization transitions in the three Mg II-selected absorption systems toward the quasar PG 1206+459. Three systems (A, B, and C), which are clustered within 1500 km s-1 at z~0.93, were originally identified in a spectrum obtained with the High Resolution Spectrograph (HIRES) on the Keck I Telescope. A WIYN (Wisconsin-Indiana-Yale-NOAO) Gunn i-band image of the quasar field and spectroscopy of two galaxy candidates are presented. A multiphase medium is seen in all three systems, consistent with smaller, denser clouds producing low-ionization transitions (Mg II, Fe II, and Si II) and larger, diffuse, photoionized clouds giving rise to higher ionization transitions (C IV, N V, and/or O VI). (1) System A, a multicloud, weak Mg II absorber at z=0.9254, requires a supersolar metallicity in both low- and high-ionization phases, unless an α-group enhancement is included. The low-ionization absorption is produced in clouds with sizes of 10-70 pc, which are surrounded in velocity space by broader, high-ionization components. With the unusually complex velocity structure resolved in the N V profiles, this system is unlikely to represent a traditional galaxy disk/corona. The most likely candidate host galaxy is a ~2L*, apparently warped, spiral at an impact parameter of 43 h-1 kpc. (2) System B, at z=0.9276, has the strongest Mg II absorption and has an approximately solar metallicity in the low-ionization phase. The smooth, broad high-ionization profiles may indicate a coronal structure similar to that of the Milky Way. The redshift of an L* galaxy (z=0.9289), at an impact parameter of 38 h-1 kpc, is consistent with the redshift of this system. (3) System C, at z=0.9342, has a single component in Mg II, separated from the other two systems by ~+1000 km s-1. The Lyα profile is not aligned with the Mg II, requiring an additional velocity component offset by

  7. Numerical Simulation of the Multiphase Flow in the Rheinsahl-Heraeus (RH) System

    NASA Astrophysics Data System (ADS)

    Geng, Dian-Qiao; Lei, Hong; He, Ji-Cheng

    2010-02-01

    Knowledge of gas-liquid multiphase flow behavior in the Rheinsahl-Heraeus (RH) system is of great significance to clarify the circulation flow rate, decarburization, and inclusion removal with a reliable description. Thus, based on the separate model of injecting gas behavior, a novel mathematical model of multiphase flow has been developed to give the distribution of gas holdup in the RH system. The numerical results show that the predicted circulation flow rates, the predicted flow velocities, and the predicted mixing times agree with the measured results in a water model and that the predicted tracer concentration curve agrees with the results obtained in an actual RH system. With a lower lifting gas flow rate, the rising gas bubbles are concentrated near the wall; with a higher lifting gas flow rate, gas bubbles can reach the center of the up-snorkel. A critical lifting gas flow rate is used to obtain the maximum circulation flow rate.

  8. Multiphase electrode microbial fuel cell system that simultaneously converts organics coexisting in water and sediment phases into electricity.

    PubMed

    An, Junyeong; Moon, Hyunsoo; Chang, In Seop

    2010-09-15

    Our challenge in this study was to harvest electricity from organics coexisting in two different phases (water and sediment) in an organics-contaminated benthic environment and to obtain increased current using a multiphase electrode microbial fuel cell (multiphase MFC). The multiphase MFC consisted of a floating electrode (FE), a midelectrode (ME), and a sediment electrode (SE) with no other components. The SE was embedded in sediment; the FE and ME were then overlaid in the water surface layer and in the middle of the water column of an aquarium, respectively. During continuous supply of organics at a COD loading rate of 94 mg of COD L(-1) day(-1) and after the cessation of organics being supplied at COD loading rates of 330 and 188 mg of COD L(-1) day(-1), the multiphase MFC showed the highest current production, as compared to the control MFCs [a floating-type MFC (FT-MFC) and two types of sediment MFCs (SMFC-A and SMFC-B)]. The total charges (in coulombs) of the multiphase MFC integrated from the currents, obtained under the three operating conditions mentioned above, were comparable to the sums of charges for the FT-MFC and SMFC. As a result, this study found that the multiphase MFC can (1) utilize organics in the sediment similarly to SMFCs, (2) use organics in the water phase similarly to FT-MFCs, and (3) obtain increased current analogous to the sum of an SMFC and a FT-MFC. Thus, it is thought that the multiphase MFC developed in this work could be suitable for use in water bodies being continuously or frequently contaminated with organic waste.

  9. Assessment of interaction potential in simulating nonisothermal multiphase systems by means of lattice Boltzmann modeling

    NASA Astrophysics Data System (ADS)

    Zarghami, Ahad; Looije, Niels; Van den Akker, Harry

    2015-08-01

    The pseudopotential lattice Boltzmann model (PP-LBM) is a very popular model for simulating multiphase systems. In this model, phase separation occurs via a short-range attraction between different phases when the interaction potential term is properly chosen. Therefore, the potential term is expected to play a significant role in the model and to affect the accuracy and the stability of the computations. The original PP-LBM suffers from some drawbacks such as being capable of dealing with low density ratios only, thermodynamic inconsistency, and spurious velocities. In this paper, we aim to analyze the PP-LBM with the view to simulate single-component (non-)isothermal multiphase systems at large density ratios and in spite of the presence of spurious velocities. For this purpose, the performance of two popular potential terms and of various implementation schemes for these potential terms is examined. Furthermore, the effects of different parameters (i.e., equation of state, viscosity, etc.) on the simulations are evaluated, and, finally, recommendations for a proper simulation of (non-)isothermal multiphase systems are presented.

  10. Computational study of the shock driven instability of a multiphase particle-gas system

    SciTech Connect

    None, None

    2016-02-01

    This paper considers the interaction of a shock wave with a multiphase particle-gas system which creates an instability somewhat similar to the Richtmyer-Meshkov instability but with a larger parameter space. Because this parameter space is large, we only present an introductory survey of the effects of many of these parameters. We highlight the effects of particle-gas coupling, incident shock strength, particle size, effective system density differences, and multiple particle relaxation time effects. We focus on dilute flows with mass loading up to 40% and do not attempt to cover all parametric combinations. Instead, we vary one parameter at a time leaving additional parametric combinations for future work. The simulations are run with the Ares code, developed at Lawrence Livermore National Laboratory, which uses a multiphase particulate transport method to model two-way momentum and energy coupling. A brief validation of these models is presented and coupling effects are explored. It is shown that even for small particles, on the order of 1μm, multi-phase coupling effects are important and diminish the circulation deposition on the interface by up to 25%. These coupling effects are shown to create large temperature deviations from the dusty gas approximation, up to 20% greater, especially at higher shock strengths. It is also found that for a multiphase instability, the vortex sheet deposited at the interface separates into two sheets. In conclusion, depending on the particle and particle-gas Atwood numbers, the instability may be suppressed or enhanced by the interactions of these two vortex sheets.

  11. Computational study of the shock driven instability of a multiphase particle-gas system

    DOE PAGES

    None, None

    2016-02-01

    This paper considers the interaction of a shock wave with a multiphase particle-gas system which creates an instability somewhat similar to the Richtmyer-Meshkov instability but with a larger parameter space. Because this parameter space is large, we only present an introductory survey of the effects of many of these parameters. We highlight the effects of particle-gas coupling, incident shock strength, particle size, effective system density differences, and multiple particle relaxation time effects. We focus on dilute flows with mass loading up to 40% and do not attempt to cover all parametric combinations. Instead, we vary one parameter at a timemore » leaving additional parametric combinations for future work. The simulations are run with the Ares code, developed at Lawrence Livermore National Laboratory, which uses a multiphase particulate transport method to model two-way momentum and energy coupling. A brief validation of these models is presented and coupling effects are explored. It is shown that even for small particles, on the order of 1μm, multi-phase coupling effects are important and diminish the circulation deposition on the interface by up to 25%. These coupling effects are shown to create large temperature deviations from the dusty gas approximation, up to 20% greater, especially at higher shock strengths. It is also found that for a multiphase instability, the vortex sheet deposited at the interface separates into two sheets. In conclusion, depending on the particle and particle-gas Atwood numbers, the instability may be suppressed or enhanced by the interactions of these two vortex sheets.« less

  12. Computational study of the shock driven instability of a multiphase particle-gas system

    NASA Astrophysics Data System (ADS)

    McFarland, Jacob A.; Black, Wolfgang J.; Dahal, Jeevan; Morgan, Brandon E.

    2016-02-01

    This paper considers the interaction of a shock wave with a multiphase particle-gas system which creates an instability similar in some ways to the Richtmyer-Meshkov instability but with a larger parameter space. As this parameter space is large, we only present an introductory survey of the effects of many of these parameters. We highlight the effects of particle-gas coupling, incident shock strength, particle size, effective system density differences, and multiple particle relaxation time effects. We focus on dilute flows with mass loading up to 40% and do not attempt to cover all parametric combinations. Instead, we vary one parameter at a time leaving additional parametric combinations for future work. The simulations are run with the Ares code, developed at Lawrence Livermore National Laboratory, which uses a multiphase particulate transport method to model two-way momentum and energy coupling. A brief validation of these models is presented and coupling effects are explored. It is shown that even for small particles, on the order of 1 μm, multi-phase coupling effects are important and diminish the circulation deposition on the interface by up to 25%. These coupling effects are shown to create large temperature deviations from the dusty gas approximation, up to 20% greater, especially at higher shock strengths. It is also found that for a multiphase instability, the vortex sheet deposited at the interface separates into two sheets. Depending on the particle and particle-gas Atwood numbers, the instability may be suppressed or enhanced by the interactions of these two vortex sheets.

  13. Comparison of two column characterisation systems based on pharmaceutical applications.

    PubMed

    Haghedooren, Erik; Németh, Tamás; Dragovic, Sanja; Noszál, Béla; Hoogmartens, Jos; Adams, Erwin

    2008-05-02

    A useful column characterisation system should help chromatographers to select the most appropriate column to use, e.g. when a particular chromatographic column is not available or when facing the dilemma of selecting a suitable column for analysis according to an official monograph. Official monographs of the European Pharmacopoeia and the United States Pharmacopeia are not allowed to mention the brand name of the stationary phase used for the method development. Also given the overwhelming offer of several hundreds of commercially available reversed-phase liquid chromatographic columns, the choice of a suitable column could be difficult sometimes. To support rational column selection, a column characterisation study was started in our laboratory in 2000. In the same period, Euerby et al. also developed a column characterisation system, which is now released as Column Selector by ACD/Labs. The aim of this project was to compare the two existing column characterisation systems, i.e. the KUL system and the Euerby system. Other research groups active in this field will not be discussed here. Euerby et al. developed a column characterisation system based on 6 test parameters, while the KUL system is based on 4 chromatographic parameters. Comparison was done using a set of 63 columns. For 7 different pharmaceutical separations (fluoxetine, gemcitabine, erythromycin, tetracycline, tetracaine, amlodipine and bisacodyl), a ranking was built based on an F-value (KUL method) or Column Difference Factor value (Euerby method) versus a (virtual) reference column. Both methods showed a similar ranking. The KUL and Euerby methods do not perfectly match, but they yield very similar results, allowing with a relatively high certainty, the selection of similar or dissimilar columns as compared to a reference column. An analyst that uses either of the two methods, will end up with a similar ranking. From a practical point of view, it must be noted that the KUL method only includes 4

  14. MULTI-PHASE CFD MODELING OF A SOLID SORBENT CARBON CAPTURE SYSTEM

    SciTech Connect

    Ryan, Emily M.; Xu, Wei; DeCroix, David; Saha, Kringan; Huckaby, E. D.; Darteville, Sebastien; Sun, Xin

    2012-05-01

    Post-combustion solid sorbent carbon capture systems are being studied via computational modeling as part of the U.S. Department of Energy’s Carbon Capture Simulation Initiative (CCSI). The work focuses on computational modeling of device-scale multi-phase computational fluid dynamics (CFD) simulations for given carbon capture reactor configurations to predict flow properties, outlet compositions, temperature and pressure. The detailed outputs of the device-scale models provide valuable insight into the operation of new carbon capture devices and will help in the design and optimization of carbon capture systems. As a first step in this project we have focused on modeling a 1 kWe solid sorbent carbon capture system using the commercial CFD software ANSYS FLUENT®. Using the multi-phase models available in ANSYS FLUENT®, we are investigating the use of Eulerian-Eulerian and Eulerian-Lagrangian methods for modeling a fluidized bed carbon capture design. The applicability of the dense discrete phase method (DDPM) is being considered along with the more traditional Eulerian-Eulerian multi-phase model. In this paper we will discuss the design of the 1 kWe solid sorbent system and the setup of the DDPM and Eulerian-Eulerian models used to simulate the system. The results of the hydrodynamics in the system will be discussed and the predictions of the DDPM and Eulerian-Eulerian simulations will be compared. A discussion of the sensitivity of the model to boundary and initial conditions, computational meshing, granular pressure, and drag sub-models will also be presented.

  15. Systems for column-based separations, methods of forming packed columns, and methods of purifying sample components

    DOEpatents

    Egorov, Oleg B.; O'Hara, Matthew J.; Grate, Jay W.; Chandler, Darrell P.; Brockman, Fred J.; Bruckner-Lea, Cynthia J.

    2000-01-01

    The invention encompasses systems for column-based separations, methods of packing and unpacking columns and methods of separating components of samples. In one aspect, the invention includes a method of packing and unpacking a column chamber, comprising: a) packing a matrix material within a column chamber to form a packed column; and b) after the packing, unpacking the matrix material from the column chamber without moving the column chamber. In another aspect, the invention includes a system for column-based separations, comprising: a) a fluid passageway, the fluid passageway comprising a column chamber and a flow path in fluid communication with the column chamber, the flow path being obstructed by a retaining material permeable to a carrier fluid and impermeable to a column matrix material suspended in the carrier fluid, the flow path extending through the column chamber and through the retaining material, the flow path being configured to form a packed column within the column chamber when a suspension of the fluid and the column matrix material is flowed along the flow path; and b) the fluid passageway extending through a valve intermediate the column chamber and the retaining material.

  16. Systems For Column-Based Separations, Methods Of Forming Packed Columns, And Methods Of Purifying Sample Components.

    DOEpatents

    Egorov, Oleg B.; O'Hara, Matthew J.; Grate, Jay W.; Chandler, Darrell P.; Brockman, Fred J.; Bruckner-Lea, Cynthia J.

    2004-08-24

    The invention encompasses systems for column-based separations, methods of packing and unpacking columns and methods of separating components of samples. In one aspect, the invention includes a method of packing and unpacking a column chamber, comprising: a) packing a matrix material within a column chamber to form a packed column; and b) after the packing, unpacking the matrix material from the column chamber without moving the column chamber. In another aspect, the invention includes a system for column-based separations, comprising: a) a fluid passageway, the fluid passageway comprising a column chamber and a flow path in fluid communication with the column chamber, the flow path being obstructed by a retaining material permeable to a carrier fluid and impermeable to a column matrix material suspended in the carrier fluid, the flow path extending through the column chamber and through the retaining material, the flow path being configured to form a packed column within the column chamber when a suspension of the fluid and the column matrix material is flowed along the flow path; and b) the fluid passageway extending through a valve intermediate the column chamber and the retaining material.

  17. Systems For Column-Based Separations, Methods Of Forming Packed Columns, And Methods Of Purifying Sample Components

    DOEpatents

    Egorov, Oleg B.; O'Hara, Matthew J.; Grate, Jay W.; Chandler, Darrell P.; Brockman, Fred J.; Bruckner-Lea, Cynthia J.

    2006-02-21

    The invention encompasses systems for column-based separations, methods of packing and unpacking columns and methods of separating components of samples. In one aspect, the invention includes a method of packing and unpacking a column chamber, comprising: a) packing a matrix material within a column chamber to form a packed column; and b) after the packing, unpacking the matrix material from the column chamber without moving the column chamber. In another aspect, the invention includes a system for column-based separations, comprising: a) a fluid passageway, the fluid passageway comprising a column chamber and a flow path in fluid communication with the column chamber, the flow path being obstructed by a retaining material permeable to a carrier fluid and impermeable to a column matrix material suspended in the carrier fluid, the flow path extending through the column chamber and through the retaining material, the flow path being configured to form a packed column within the column chamber when a suspension of the fluid and the column matrix material is flowed along the flow path; and b) the fluid passageway extending through a valve intermediate the column chamber and the retaining material.

  18. Assessment of column selection systems using Partial Least Squares.

    PubMed

    Žuvela, Petar; Liu, J Jay; Plenis, Alina; Bączek, Tomasz

    2015-11-13

    Column selection systems based on calculation of a scalar measure based on Euclidean distance between chromatographic columns, suffer from the same issue. For diverse values of their parameters, identical or near-identical values can be calculated. Proper use of chemometric methods can not only provide a remedy, but also reveal underlying correlation between them. In this work, parameters of a well-established column selection system (CSS) developed at Katholieke Universiteit Leuven (KUL CSS) have been directly correlated to parameters of selectivity (retention time, resolution, and peak/valley ratio) toward pharmaceuticals, by employing Partial Least Squares (PLS). Two case studies were evaluated, separation of alfuzosin, lamotrigine, and their impurities, respectively. Within them, comprehensive correlation structure was revealed, which was thoroughly interpreted, confirming a causal relationship between KUL parameters and parameters of column performance. Furthermore, it was shown that the developed methodology can be applied to any distance-based column selection system.

  19. Detection of Ne VIII in an Intervening Multiphase Absorption System Toward 3C 263

    NASA Astrophysics Data System (ADS)

    Narayanan, Anand; Wakker, Bart P.; Savage, Blair D.

    2009-09-01

    We report the detection of Ne VIII in an intervening multiphase absorption line system at z = 0.32566 in the Far Ultraviolet Spectroscopic Explorer spectrum of the quasar 3C 263 (zem = 0.646). The Ne VIII λ770 Å detection has a 3.9σ significance. At the same velocity, we also find absorption lines from C IV, O III, O IV, and N IV. The line parameter measurements yield log [N(Ne VIII) cm-2] = 13.98+0.10 -0.13 and b = 49.8 ± 5.5 km s-1. We find that the ionization mechanism in the gas phase giving rise to the Ne VIII absorption is inconsistent with photoionization. The absorber has a multiphase structure, with the intermediate ions produced in cool photoionized gas and the Ne VIII most likely in a warm collisionally ionized medium in the temperature range (0.5-1.0) × 106 K. This is the second ever detection of an intervening Ne VIII absorption system. Its properties resemble the previous Ne VIII absorber reported by Savage and colleagues. Direct observations of H I and O VI are needed to better constrain the physical conditions in the collisionally ionized gas phase of this absorber. Based on observations with the NASA-CNES-CSA Far Ultraviolet Spectroscopic Explorer operated by Johns Hopkins University, supported by NASA contract NAS5-32985.

  20. Study on electrodynamic sensor of multi-modality system for multiphase flow measurement

    NASA Astrophysics Data System (ADS)

    Deng, Xiang; Chen, Dixiang; Yang, Wuqiang

    2011-12-01

    Accurate measurement of multiphase flows, including gas/solids, gas/liquid, and liquid/liquid flows, is still challenging. In principle, electrical capacitance tomography (ECT) can be used to measure the concentration of solids in a gas/solids flow and the liquid (e.g., oil) fraction in a gas/liquid flow, if the liquid is non-conductive. Electrical resistance tomography (ERT) can be used to measure a gas/liquid flow, if the liquid is conductive. It has been attempted to use a dual-modality ECT/ERT system to measure both the concentration profile and the velocity profile by pixel-based cross correlation. However, this approach is not realistic because of the dynamic characteristics and the complexity of multiphase flows and the difficulties in determining the velocities by cross correlation. In this paper, the issues with dual modality ECT/ERT and the difficulties with pixel-based cross correlation will be discussed. A new adaptive multi-modality (ECT, ERT and electro-dynamic) sensor, which can be used to measure a gas/solids or gas/liquid flow, will be described. Especially, some details of the electrodynamic sensor of multi-modality system such as sensing electrodes optimum design, electrostatic charge amplifier, and signal processing will be discussed. Initial experimental results will be given.

  1. Study on electrodynamic sensor of multi-modality system for multiphase flow measurement.

    PubMed

    Deng, Xiang; Chen, Dixiang; Yang, Wuqiang

    2011-12-01

    Accurate measurement of multiphase flows, including gas/solids, gas/liquid, and liquid/liquid flows, is still challenging. In principle, electrical capacitance tomography (ECT) can be used to measure the concentration of solids in a gas/solids flow and the liquid (e.g., oil) fraction in a gas/liquid flow, if the liquid is non-conductive. Electrical resistance tomography (ERT) can be used to measure a gas/liquid flow, if the liquid is conductive. It has been attempted to use a dual-modality ECT/ERT system to measure both the concentration profile and the velocity profile by pixel-based cross correlation. However, this approach is not realistic because of the dynamic characteristics and the complexity of multiphase flows and the difficulties in determining the velocities by cross correlation. In this paper, the issues with dual modality ECT/ERT and the difficulties with pixel-based cross correlation will be discussed. A new adaptive multi-modality (ECT, ERT and electro-dynamic) sensor, which can be used to measure a gas/solids or gas/liquid flow, will be described. Especially, some details of the electrodynamic sensor of multi-modality system such as sensing electrodes optimum design, electrostatic charge amplifier, and signal processing will be discussed. Initial experimental results will be given.

  2. Multi-phase CFD modeling of solid sorbent carbon capture system

    SciTech Connect

    Ryan, E. M.; DeCroix, D.; Breault, Ronald W.; Xu, W.; Huckaby, E. David

    2013-01-01

    Computational fluid dynamics (CFD) simulations are used to investigate a low temperature post-combustion carbon capture reactor. The CFD models are based on a small scale solid sorbent carbon capture reactor design from ADA-ES and Southern Company. The reactor is a fluidized bed design based on a silica-supported amine sorbent. CFD models using both Eulerian–Eulerian and Eulerian–Lagrangian multi-phase modeling methods are developed to investigate the hydrodynamics and adsorption of carbon dioxide in the reactor. Models developed in both FLUENT® and BARRACUDA are presented to explore the strengths and weaknesses of state of the art CFD codes for modeling multi-phase carbon capture reactors. The results of the simulations show that the FLUENT® Eulerian–Lagrangian simulations (DDPM) are unstable for the given reactor design; while the BARRACUDA Eulerian–Lagrangian model is able to simulate the system given appropriate simplifying assumptions. FLUENT® Eulerian–Eulerian simulations also provide a stable solution for the carbon capture reactor given the appropriate simplifying assumptions.

  3. Multi-Phase CFD Modeling of Solid Sorbent Carbon Capture System

    SciTech Connect

    Ryan, Emily M.; DeCroix, David; Breault, Ronald W.; Xu, Wei; Huckaby, E. D.; Saha, Kringan; Darteville, Sebastien; Sun, Xin

    2013-07-30

    Computational fluid dynamics (CFD) simulations are used to investigate a low temperature post-combustion carbon capture reactor. The CFD models are based on a small scale solid sorbent carbon capture reactor design from ADA-ES and Southern Company. The reactor is a fluidized bed design based on a silica-supported amine sorbent. CFD models using both Eulerian-Eulerian and Eulerian-Lagrangian multi-phase modeling methods are developed to investigate the hydrodynamics and adsorption of carbon dioxide in the reactor. Models developed in both FLUENT® and BARRACUDA are presented to explore the strengths and weaknesses of state of the art CFD codes for modeling multi-phase carbon capture reactors. The results of the simulations show that the FLUENT® Eulerian-Lagrangian simulations (DDPM) are unstable for the given reactor design; while the BARRACUDA Eulerian-Lagrangian model is able to simulate the system given appropriate simplifying assumptions. FLUENT® Eulerian-Eulerian simulations also provide a stable solution for the carbon capture reactor given the appropriate simplifying assumptions.

  4. Looking East at Motor Control System, Clarity Columns and Blend ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Looking East at Motor Control System, Clarity Columns and Blend Tank Along East Side of Recycle Recovery Building - Hematite Fuel Fabrication Facility, Recycle Recovery Building, 3300 State Road P, Festus, Jefferson County, MO

  5. Compact high-resolution gamma-ray computed tomography system for multiphase flow studies

    SciTech Connect

    Bieberle, A.; Nehring, H.; Berger, R.; Arlit, M.; Haerting, H.-U.; Schubert, M.; Hampel, U.

    2013-03-15

    In this paper, a compact high-resolution gamma-ray Computed Tomography (CompaCT) measurement system for multiphase flow studies and tomographic imaging of technical objects is presented. Its compact and robust design makes it particularly suitable for studies on industrial facilities and outdoor applications. Special care has been given to thermal ruggedness, shock resistance, and radiation protection. Main components of the system are a collimated {sup 137}Cs isotopic source, a thermally stabilised modular high-resolution gamma-ray detector arc with 112 scintillation detector elements, and a transportable rotary unit. The CompaCT allows full CT scans of objects with a diameter of up to 130 mm and can be operated with any tilting angle from 0 Degree-Sign (horizontal) to 90 Degree-Sign (vertical).

  6. [An integral chip for the multiphase pulse-duration modulation used for voltage changer in biomedical microprocessor systems].

    PubMed

    Balashov, A M; Selishchev, S V

    2004-01-01

    An integral chip (IC) was designed for controlling the step-down pulse voltage converter, which is based on the multiphase pulse-duration modulation, for use in biomedical microprocessor systems. The CMOS technology was an optimal basis for the IC designing. An additional feedback circuit diminishes the output voltage dispersion at dynamically changing loads.

  7. Mixing and Demixing Processes in Multiphase Flows With Application to Propulsion Systems

    NASA Technical Reports Server (NTRS)

    Decker, Rand (Editor); Schafer, Charles F. (Editor)

    1988-01-01

    A workshop on transport processes in multiphase flow was held at the Marshall Space Flight Center on February 25 and 26, 1988. The program, abstracts and text of the presentations at this workshop are presented. The objective of the workshop was to enhance our understanding of mass, momentum, and energy transport processes in laminar and turbulent multiphase shear flows in combustion and propulsion environments.

  8. Computer Assisted Gamma and X-Ray Tomography: Applications to Multiphase Flow Systems.

    SciTech Connect

    Kumar, Sailesh B.; Dudukovic, Milorad P.; Toseland, Bernard A.

    1997-03-01

    The application of X-ray and gamma ray transmission tomography to the study of process engineering systems is reviewed. The fundamental principles of tomography, the algorithms for image reconstruction, the measurement method and the possible sources of error are discussed in detail. A case study highlights the methodology involved in designing a scanning system for the study of a given process unit, e.g., reactor, separations column etc. Results obtained in the authors` laboratory for the gas holdup distribution in bubble columns are also presented. Recommendations are made for the Advanced Fuels Development Unit (AFDU) in LaPorte, TX.

  9. A simple parallel gas chromatography column screening system.

    PubMed

    Schafer, Wes; Hamilton, Simon E; Pirzada, Zainab; Welch, Christopher J

    2012-01-01

    A simple approach to the automated screening of four different columns on a single gas chromatography (GC) instrument is used for rapid chiral GC method development. Configuration of a conventional GC instrument with a second autosampler and several inexpensive Y-splitters enables simultaneous evaluation of two different columns, allowing a total of four different columns to be evaluated in two automated back to back runs. The resulting system affords a simple and effective approach to chiral GC method development that speeds analysis while eliminating the need for slow and tedious manual interchange of columns. An example of developing a rapid isothermal GC method from the screening results obtained by the instrument is also shown.

  10. Method and system for measuring multiphase flow using multiple pressure differentials

    DOEpatents

    Fincke, James R.

    2001-01-01

    An improved method and system for measuring a multiphase flow in a pressure flow meter. An extended throat venturi is used and pressure of the multiphase flow is measured at three or more positions in the venturi, which define two or more pressure differentials in the flow conduit. The differential pressures are then used to calculate the mass flow of the gas phase, the total mass flow, and the liquid phase. The method for determining the mass flow of the high void fraction fluid flow and the gas flow includes certain steps. The first step is calculating a gas density for the gas flow. The next two steps are finding a normalized gas mass flow rate through the venturi and computing a gas mass flow rate. The following step is estimating the gas velocity in the venturi tube throat. The next step is calculating the pressure drop experienced by the gas-phase due to work performed by the gas phase in accelerating the liquid phase between the upstream pressure measuring point and the pressure measuring point in the venturi throat. Another step is estimating the liquid velocity in the venturi throat using the calculated pressure drop experienced by the gas-phase due to work performed by the gas phase. Then the friction is computed between the liquid phase and a wall in the venturi tube. Finally, the total mass flow rate based on measured pressure in the venturi throat is calculated, and the mass flow rate of the liquid phase is calculated from the difference of the total mass flow rate and the gas mass flow rate.

  11. DENSE MULTIPHASE FLOW SIMULATION: CONTINUUM MODEL FOR POLY-DISPERSED SYSTEMS USING KINETIC THEORY

    SciTech Connect

    Moses Bogere

    2011-08-31

    The overall objective of the project was to verify the applicability of the FCMOM approach to the kinetic equations describing the particle flow dynamics. For monodispersed systems the fundamental equation governing the particle flow dynamics is the Boltzmann equation. During the project, the FCMOM was successfully applied to several homogeneous and in-homogeneous problems in different flow regimes, demonstrating that the FCMOM has the potential to be used to solve efficiently the Boltzmann equation. However, some relevant issues still need to be resolved, i.e. the homogeneous cooling problem (inelastic particles cases) and the transition between different regimes. In this report, the results obtained in homogeneous conditions are discussed first. Then a discussion of the validation results for in-homogeneous conditions is provided. And finally, a discussion will be provided about the transition between different regimes. Alongside the work on development of FCMOM approach studies were undertaken in order to provide insights into anisotropy or particles kinetics in riser hydrodynamics. This report includes results of studies of multiphase flow with unequal granular temperatures and analysis of momentum re-distribution in risers due to particle-particle and fluid-particle interactions. The study of multiphase flow with unequal granular temperatures entailed both simulation and experimental studies of two particles sizes in a riser and, a brief discussion of what was accomplished will be provided. And finally, a discussion of the analysis done on momentum re-distribution of gas-particles flow in risers will be provided. In particular a discussion of the remaining work needed in order to improve accuracy and predictability of riser hydrodynamics based on two-fluid models and how they can be used to model segregation in risers.

  12. Effects of system densities on distillation column performance

    SciTech Connect

    Fasesan, S.O.; Sanni, S.A.; Taiwo, E.A.

    1998-06-01

    Distillation experiments were carried out on three binary systems (ethanol-butanol, ethanol-propan-2-ol, and propan-2-ol-butanol) in a 0.1-m internal diameter glass column packed with 8 mm diameter Raschig rings. The experiments were performed under total reflux conditions and at atmospheric pressure. The data collected on column performance showed that performance declined with increasing average bulk liquid density. The results also lend credence to earlier reports on the behavior of column performance with respect to component concentration in the feed mixtures. The system densities of the three binary systems were measured at four different temperatures, 30, 40, 50, and 60 C. The data were compared with the predicted data of Yen-Woods and Multifluid models. The accuracy of the predictions of the Yen-Woods model was rather poor while that of the Multifluid model was very encouraging.

  13. Direct coupling of microbore HPLC columns to MS systems

    NASA Technical Reports Server (NTRS)

    Mcnair, H. M.

    1985-01-01

    A detailed investigation using electron microscopy was conducted which examined the conditions of materials used in the construction of stable, high performance microbore liquid chromatography (LC) columns. Small details proved to be important. The effects of temperature on the elution of several homologous series used as probe compounds was examined in reverse phase systems. They showed that accessible temperature changes provide roughly half the increase in solvent strength that would be obtained going from a 100% aqueous to a 100% organic mobile phase, which is sufficient to warrant their use in many analyses requiring the use of gradients. Air circulation temperature control systems provide the easiest means of obtaining rapid, wide range changes in column temperature. However, slow heat transfer from the gas leads to thermal nonuniformity in the column and a decrease in resolution as the temperature program progresses.

  14. Density-based separation in multiphase systems provides a simple method to identify sickle cell disease

    PubMed Central

    Kumar, Ashok A.; Patton, Matthew R.; Hennek, Jonathan W.; Lee, Si Yi Ryan; D’Alesio-Spina, Gaetana; Yang, Xiaoxi; Kanter, Julie; Shevkoplyas, Sergey S.; Brugnara, Carlo; Whitesides, George M.

    2014-01-01

    Although effective low-cost interventions exist, child mortality attributable to sickle cell disease (SCD) remains high in low-resource areas due, in large part, to the lack of accessible diagnostic methods. The presence of dense (ρ > 1.120 g/cm3) cells is characteristic of SCD. The fluid, self-assembling step-gradients in density created by aqueous multiphase systems (AMPSs) identifies SCD by detecting dense cells. AMPSs separate different forms of red blood cells by density in a microhematocrit centrifuge and provide a visual means to distinguish individuals with SCD from those with normal hemoglobin or with nondisease, sickle-cell trait in under 12 min. Visual evaluation of a simple two-phase system identified the two main subclasses of SCD [homozygous (Hb SS) and heterozygous (Hb SC)] with a sensitivity of 90% (73–98%) and a specificity of 97% (86–100%). A three-phase system identified these two types of SCD with a sensitivity of 91% (78–98%) and a specificity of 88% (74–98%). This system could also distinguish between Hb SS and Hb SC. To the authors’ knowledge, this test demonstrates the first separation of cells by density with AMPSs, and the usefulness of AMPSs in point-of-care diagnostic hematology. PMID:25197072

  15. High pressure rheology of gas hydrate formed from multiphase systems using modified Couette rheometer.

    PubMed

    Pandey, Gaurav; Linga, Praveen; Sangwai, Jitendra S

    2017-02-01

    Conventional rheometers with concentric cylinder geometries do not enhance mixing in situ and thus are not suitable for rheological studies of multiphase systems under high pressure such as gas hydrates. In this study, we demonstrate the use of modified Couette concentric cylinder geometries for high pressure rheological studies during the formation and dissociation of methane hydrate formed from pure water and water-decane systems. Conventional concentric cylinder Couette geometry did not produce any hydrates in situ and thus failed to measure rheological properties during hydrate formation. The modified Couette geometries proposed in this work observed to provide enhanced mixing in situ, thus forming gas hydrate from the gas-water-decane system. This study also nullifies the use of separate external high pressure cell for such measurements. The modified geometry was observed to measure gas hydrate viscosity from an initial condition of 0.001 Pa s to about 25 Pa s. The proposed geometries also possess the capability to measure dynamic viscoelastic properties of hydrate slurries at the end of experiments. The modified geometries could also capture and mimic the viscosity profile during the hydrate dissociation as reported in the literature. The present study acts as a precursor for enhancing our understanding on the rheology of gas hydrate formed from various systems containing promoters and inhibitors in the context of flow assurance.

  16. High pressure rheology of gas hydrate formed from multiphase systems using modified Couette rheometer

    NASA Astrophysics Data System (ADS)

    Pandey, Gaurav; Linga, Praveen; Sangwai, Jitendra S.

    2017-02-01

    Conventional rheometers with concentric cylinder geometries do not enhance mixing in situ and thus are not suitable for rheological studies of multiphase systems under high pressure such as gas hydrates. In this study, we demonstrate the use of modified Couette concentric cylinder geometries for high pressure rheological studies during the formation and dissociation of methane hydrate formed from pure water and water-decane systems. Conventional concentric cylinder Couette geometry did not produce any hydrates in situ and thus failed to measure rheological properties during hydrate formation. The modified Couette geometries proposed in this work observed to provide enhanced mixing in situ, thus forming gas hydrate from the gas-water-decane system. This study also nullifies the use of separate external high pressure cell for such measurements. The modified geometry was observed to measure gas hydrate viscosity from an initial condition of 0.001 Pa s to about 25 Pa s. The proposed geometries also possess the capability to measure dynamic viscoelastic properties of hydrate slurries at the end of experiments. The modified geometries could also capture and mimic the viscosity profile during the hydrate dissociation as reported in the literature. The present study acts as a precursor for enhancing our understanding on the rheology of gas hydrate formed from various systems containing promoters and inhibitors in the context of flow assurance.

  17. Thermodynamic approach to the stability of multi-phase systems: application to the Y2O3-Fe system

    NASA Astrophysics Data System (ADS)

    Samolyuk, G. D.; Osetsky, Y. N.

    2015-08-01

    Oxide-metal systems are important in many practical applications, and they are undergoing extensive study using a wide range of techniques. The most accurate theoretical approaches are based on density functional theory (DFT), which is limited to ~102 atoms. Multi-scale approaches, e.g. DFT + Monte Carlo, are often used to model oxide metal systems at the atomic level. These approaches can qualitatively describe the kinetics of some processes but not the overall stability of individual phases. In this article, we propose a thermodynamic approach to study equilibrium in multi-phase systems, which can be sequentially enhanced by considering different defects and microstructures. We estimate the thermodynamic equilibrium by minimization of the free energy of the whole multi-phase system using a limited set of defects and microstructural objects for which the properties are calculated by DFT. As an example, we consider Y2O3 + bcc Fe with vacancies in both the Y2O3 and bcc Fe phases, Y substitutions and O interstitials in Fe, Fe impurities, and antisite defects in Y2O3. The output of these calculations is the thermal equilibrium concentration of all the defects for a particular temperature and composition. The results obtained confirmed the high temperature stability of yttria in iron. Model development toward more accurate calculations is discussed.

  18. Thermodynamic approach to the stability of multi-phase systems: application to the Y2O3-Fe system.

    PubMed

    Samolyuk, G D; Osetsky, Y N

    2015-08-05

    Oxide-metal systems are important in many practical applications, and they are undergoing extensive study using a wide range of techniques. The most accurate theoretical approaches are based on density functional theory (DFT), which is limited to ~10(2) atoms. Multi-scale approaches, e.g. DFT + Monte Carlo, are often used to model oxide metal systems at the atomic level. These approaches can qualitatively describe the kinetics of some processes but not the overall stability of individual phases. In this article, we propose a thermodynamic approach to study equilibrium in multi-phase systems, which can be sequentially enhanced by considering different defects and microstructures. We estimate the thermodynamic equilibrium by minimization of the free energy of the whole multi-phase system using a limited set of defects and microstructural objects for which the properties are calculated by DFT. As an example, we consider Y2O3 + bcc Fe with vacancies in both the Y2O3 and bcc Fe phases, Y substitutions and O interstitials in Fe, Fe impurities, and antisite defects in Y2O3. The output of these calculations is the thermal equilibrium concentration of all the defects for a particular temperature and composition. The results obtained confirmed the high temperature stability of yttria in iron. Model development toward more accurate calculations is discussed.

  19. Thermal Analysis for Ion-Exchange Column System

    SciTech Connect

    Lee, Si Y.; King, William D.

    2012-12-20

    Models have been developed to simulate the thermal characteristics of crystalline silicotitanate ion exchange media fully loaded with radioactive cesium either in a column configuration or distributed within a waste storage tank. This work was conducted to support the design and operation of a waste treatment process focused on treating dissolved, high-sodium salt waste solutions for the removal of specific radionuclides. The ion exchange column will be installed inside a high level waste storage tank at the Savannah River Site. After cesium loading, the ion exchange media may be transferred to the waste tank floor for interim storage. Models were used to predict temperature profiles in these areas of the system where the cesium-loaded media is expected to lead to localized regions of elevated temperature due to radiolytic decay. Normal operating conditions and accident scenarios (including loss of solution flow, inadvertent drainage, and loss of active cooling) were evaluated for the ion exchange column using bounding conditions to establish the design safety basis. The modeling results demonstrate that the baseline design using one central and four outer cooling tubes provides a highly efficient cooling mechanism for reducing the maximum column temperature. In-tank modeling results revealed that an idealized hemispherical mound shape leads to the highest tank floor temperatures. In contrast, even large volumes of CST distributed in a flat layer with a cylindrical shape do not result in significant floor heating.

  20. Multiphase pumping - operation & control

    SciTech Connect

    Salis, J. de; Marolies, C. de; Falcimaigne, J.

    1996-12-31

    This paper reviews field issues related to the planning, installation and operation of the helico-axial multiphase pumps. Interest for multiphase production, which leads to simpler and smaller in-field installations, is primarily dictated by the need for more a cost effective production system. Multiphase pumping is essentially a means of adding energy to the unprocessed effluent which enables the liquid/gas mixture to be transported over long distances without the need for prior separation. The Poseidon helico-axial pumps, under normal operating conditions, are largely unaffected by process fluctuations at pump inlet (changes in pressure, liquid or gas flow rate). They have demonstrated a stable behavior (self-adaptive capability with regards to instantaneous changes). A multiphase pump set is designed to operate under changing/fluctuating process conditions. An important issue related to pump operability and flexibility has to do with the driver selection: fixed speed vs. variable speed. In some cases a fixed speed drive provides sufficient operational flexibility. In other cases variable speed can be chosen. Pump operation & control strategies are presented and discussed.

  1. Gullfaks multiphase booster project

    SciTech Connect

    Vangen, G.; Carstensen, C.; Bakken, L.E.

    1995-12-31

    A Poseidon Multiphase Pump has been Installed and is presently running on Statoil`s Gullfaks A platform in the North Sea, giving additional pressure to one of the wells. The main objective of this work has been to qualify the Poseidon Booster Technology, technically and operationally, and to provide a reliable and industrialized tool for multiphase boosting, either sub sea or installed topside a platform. The paper gives a brief summary of the project and describes the Poseidon pump, the platform installation and outlines the experience and results from the ongoing qualification test. The Gullfaks booster, as delivered by Framo Engineering AS, has up to January 1995 accumulated 2,400 running hours. The booster is fully integrated into the production systems on the platform. The daily operations are carried out from the central control room by the ordinary platform staff. The objectives of the test program have so far been successfully fulfilled. Multiphase booster technology combined with progress in multiphase flow technology will have a significant impact on development and production of smaller oil and gas fields that today are assumed to be non-profitable.

  2. Hybrid dynamic radioactive particle tracking (RPT) calibration technique for multiphase flow systems

    NASA Astrophysics Data System (ADS)

    Khane, Vaibhav; Al-Dahhan, Muthanna H.

    2017-04-01

    The radioactive particle tracking (RPT) technique has been utilized to measure three-dimensional hydrodynamic parameters for multiphase flow systems. An analytical solution to the inverse problem of the RPT technique, i.e. finding the instantaneous tracer positions based upon instantaneous counts received in the detectors, is not possible. Therefore, a calibration to obtain a counts-distance map is needed. There are major shortcomings in the conventional RPT calibration method due to which it has limited applicability in practical applications. In this work, the design and development of a novel dynamic RPT calibration technique are carried out to overcome the shortcomings of the conventional RPT calibration method. The dynamic RPT calibration technique has been implemented around a test reactor with 1foot in diameter and 1 foot in height using Cobalt-60 as an isotopes tracer particle. Two sets of experiments have been carried out to test the capability of novel dynamic RPT calibration. In the first set of experiments, a manual calibration apparatus has been used to hold a tracer particle at known static locations. In the second set of experiments, the tracer particle was moved vertically downwards along a straight line path in a controlled manner. The obtained reconstruction results about the tracer particle position were compared with the actual known position and the reconstruction errors were estimated. The obtained results revealed that the dynamic RPT calibration technique is capable of identifying tracer particle positions with a reconstruction error between 1 to 5.9 mm for the conditions studied which could be improved depending on various factors outlined here.

  3. Enrichment of reticulocytes from whole blood using aqueous multiphase systems of polymers.

    PubMed

    Kumar, Ashok A; Lim, Caeul; Moreno, Yovany; Mace, Charles R; Syed, Abeer; Van Tyne, Daria; Wirth, Dyann F; Duraisingh, Manoj T; Whitesides, George M

    2015-01-01

    This paper demonstrates the enrichment of reticulocytes by centrifuging whole blood through aqueous multiphase systems (AMPSs)-immiscible phases of solutions of polymers that form step-gradients in density. The interfaces of an AMPS concentrate cells; this concentration facilitates the extraction of blood enriched for reticulocytes. AMPS enrich reticulocytes from blood from both healthy and hemochromatosis donors. Varying the osmolality and density of the phases of AMPS provides different levels of enrichment and yield of reticulocytes. A maximum enrichment of reticulocytemia of 64 ± 3% was obtained from donors with hemochromatosis. When used on peripheral blood from normal donors, AMPS can provide a higher yield of enriched reticulocytes and a higher proportion of reticulocytes expressing CD71 than differential centrifugation followed by centrifugation over Percoll. Blood enriched for reticulocytes by AMPS could be useful for research on malaria. Several species of malaria parasites show a preference to invade young erythrocytes and reticulocytes; this preference complicates in vitro cultivation of these species in human blood. Plasmodium knowlesi malaria parasites invade normal human blood enriched for reticulocytes by AMPSs at a rate 2.2 times greater (P < 0.01) than they invade unenriched blood. Parasite invasion in normal blood enriched by AMPS was 1.8 times greater (P < 0.05) than in blood enriched to a similar reticulocytemia by differential centrifugation followed by centrifugation over Percoll. The enrichment of reticulocytes that are invaded by malaria parasites demonstrates that AMPSs can provide a label-free method to enrich cells for biological research.

  4. Novel multiphase systems based on thermoplastic chitosan: Analysis of the structure-properties relationships

    NASA Astrophysics Data System (ADS)

    Avérous, Luc; Pollet, Eric

    2016-03-01

    In the last years, biopolymers have attracted great attention. It is for instance the case of chitosan, a linear polysaccharide. It is a deacetylated derivative of chitin, which is the second most abundant polysaccharide found in nature after cellulose. Chitosan has been found to be nontoxic, biodegradable, biofunctional, and biocompatible in addition to having antimicrobial and antifungal properties, and thus has a great potential for environmental (packaging,) or biomedical applications.For preparing chitosan-based materials, only solution casting or similar methods have been used in all the past studies. Solution casting have the disadvantage in low efficiency and difficulty in scaling-up towards industrial applications. Besides, a great amount of environmentally unfriendly chemical solvents are used and released to the environment in this method. The reason for not using a melt processing method like extrusion or kneading in the past studies is that chitosan, like many other polysaccharides such as starch, has very low thermal stability and degrade prior to melting. Therefore, even if the melt processing method is more convenient and highly preferred for industrial production, its adaptation for polysaccharide-based materials remains very difficult. However, our recently published studies has demonstrated the successful use of an innovative melt processing method (internal mixer, extrusion,) as an alternative route to solution casting, for preparing materials based on thermoplastic chitosan. These promising thermoplastic materials, obtained by melt processing, have been the main topic of recent international projects, with partners from different countries Multiphase systems based on various renewable plasticizers have been elaborated and studied. Besides, different blends, and nano-biocomposites based on nanoclays, have been elaborated and fully analyzed. The initial consortium of this vast project was based on an international consortium (Canada, Australia

  5. An Integrated RELAP5-3D and Multiphase CFD Code System Utilizing a Semi Implicit Coupling Technique

    SciTech Connect

    D.L. Aumiller; E.T. Tomlinson; W.L. Weaver

    2001-06-21

    An integrated code system consisting of RELAP5-3D and a multiphase CFD program has been created through the use of a generic semi-implicit coupling algorithm. Unlike previous CFD coupling work, this coupling scheme is numerically stable provided the material Courant limit is not violated in RELAP5-3D or at the coupling locations. The basis for the coupling scheme and details regarding the unique features associated with the application of this technique to a four-field CFD program are presented. Finally, the results of a verification problem are presented. The coupled code system is shown to yield accurate and numerically stable results.

  6. Engineered Barrier Systems Thermal-Hydraulic-Chemical Column Test Report

    SciTech Connect

    W.E. Lowry

    2001-12-13

    The Engineered Barrier System (EBS) Thermal-Hydraulic-Chemical (THC) Column Tests provide data needed for model validation. The EBS Degradation, Flow, and Transport Process Modeling Report (PMR) will be based on supporting models for in-drift THC coupled processes, and the in-drift physical and chemical environment. These models describe the complex chemical interaction of EBS materials, including granular materials, with the thermal and hydrologic conditions that will be present in the repository emplacement drifts. Of particular interest are the coupled processes that result in mineral and salt dissolution/precipitation in the EBS environment. Test data are needed for thermal, hydrologic, and geochemical model validation and to support selection of introduced materials (CRWMS M&O 1999c). These column tests evaluated granular crushed tuff as potential invert ballast or backfill material, under accelerated thermal and hydrologic environments. The objectives of the THC column testing are to: (1) Characterize THC coupled processes that could affect performance of EBS components, particularly the magnitude of permeability reduction (increases or decreases), the nature of minerals produced, and chemical fractionation (i.e., concentrative separation of salts and minerals due to boiling-point elevation). (2) Generate data for validating THC predictive models that will support the EBS Degradation, Flow, and Transport PMR, Rev. 01.

  7. The multiphase flow system used in exploiting depleted reservoirs: water-based Micro-bubble drilling fluid

    NASA Astrophysics Data System (ADS)

    Li-hui, Zheng; Xiao-qing, He; Li-xia, Fu; Xiang-chun, Wang

    2009-02-01

    Water-based micro-bubble drilling fluid, which is used to exploit depleted reservoirs, is a complicated multiphase flow system that is composed of gas, water, oil, polymer, surfactants and solids. The gas phase is separate from bulk water by two layers and three membranes. They are "surface tension reducing membrane", "high viscosity layer", "high viscosity fixing membrane", "compatibility enhancing membrane" and "concentration transition layer of liner high polymer (LHP) & surfactants" from every gas phase centre to the bulk water. "Surface tension reducing membrane", "high viscosity layer" and "high viscosity fixing membrane" bond closely to pack air forming "air-bag", "compatibility enhancing membrane" and "concentration transition layer of LHP & surfactants" absorb outside "air-bag" to form "incompact zone". From another point of view, "air-bag" and "incompact zone" compose micro-bubble. Dynamic changes of "incompact zone" enable micro-bubble to exist lonely or aggregate together, and lead the whole fluid, which can wet both hydrophilic and hydrophobic surface, to possess very high viscosity at an extremely low shear rate but to possess good fluidity at a higher shear rate. When the water-based micro-bubble drilling fluid encounters leakage zones, it will automatically regulate the sizes and shapes of the bubbles according to the slot width of fracture, the height of cavern as well as the aperture of openings, or seal them by making use of high viscosity of the system at a very low shear rate. Measurements of the rheological parameters indicate that water-based micro-bubble drilling fluid has very high plastic viscosity, yield point, initial gel, final gel and high ratio of yield point and plastic viscosity. All of these properties make the multiphase flow system meet the requirements of petroleum drilling industry. Research on interface between gas and bulk water of this multiphase flow system can provide us with information of synthesizing effective agents to

  8. Computer assisted gamma and X-ray tomography: Applications to multiphase flow systems

    SciTech Connect

    Kumar, S.B.; Dudukovic, M.

    1998-01-01

    In process vessels, involving two or three phases it is often important not only to know the volume fraction (holdup) of each phase but also the spatial distribution of such holdups. This information is needed in control, trouble shooting and assessment of flow patterns and can be observed noninvasively by the application of Computed Tomography (CT). This report presents a complete overview of X-ray and gamma ray transmission tomography principles, equipment design to specific tasks and application in process industry. The fundamental principles of tomography, the algorithms for image reconstruction, the measurement method and the possible sources of error are discussed in detail. A case study highlights the methodology involved in designing a scanning system for the study of a given process unit, e.g., reactor, separations column etc. Results obtained in the authors` laboratory for the gas holdup distribution in bubble columns are also presented. Recommendations are made for the Advanced Fuels Development Unit (AFDU) in LaPorte, TX.

  9. Use of Nuclear Magnetic Resonance as an Experimental Probe in Multiphase Systems: Determination of the Instrument Weight Function for Measurements of Liquid-Phase Volume Fractions

    NASA Astrophysics Data System (ADS)

    Maneval, J. E.; McCarthy, M. J.; Whitaker, S.

    1990-11-01

    The relativist approach (Baveye and Sposito (1984)) to the interpretation of measurements in multiphase systems was proposed in order to incorporate the details of measurements into theoretical analyses of multiphase transport processes. To help establish the utility of this approach, the weight functions for actual experimental probes must be determined. In this paper we analyze the measurement of liquid-phase porosity in a model system by nuclear magnetic resonance imaging. We show how both nuclear magnetic resonance (NMR) physics and experimental technique combine to determine the weight function for the spin-warp spin-echo sequence. The analysis shows clearly what aspects of the weight function are determined by the experimental method and what aspects are determined by the system being studied. The results will help establish the utility of the relativist approach as well as improve understanding NMR measurements in multiphase systems.

  10. AM-DMC-AMPS Multi-Functionalized Magnetic Nanoparticles for Efficient Purification of Complex Multiphase Water System

    NASA Astrophysics Data System (ADS)

    Ge, Yuru; Li, Yushu; Zu, Baiyi; Zhou, Chaoyu; Dou, Xincun

    2016-04-01

    Complex multiphase waste system purification, as one of the major challenges in many industrial fields, urgently needs an efficient one-step purification method to remove several pollutants simultaneously and efficiently. Multi-functionalized magnetic nanoparticles, Fe3O4@SiO2-MPS-AM-DMC-AMPS, were facilely prepared via a one-pot in situ polymerization of three different functional monomers, AM, DMC, and AMPS, on a Fe3O4@SiO2-MPS core-shell structure. The multi-functionalized magnetic nanoparticles (MNPs) are proven to be a highly effective purification agent for oilfield wastewater, an ideal example of industrial complex multiphase waste system containing cations, anions, and organic pollutants. Excellent overall removal efficiencies for both cations, including K+, Ca2+, Na+, and Mg2+ of 80.68 %, and anions, namely Cl- and SO4 2-, of 85.18 % along with oil of 97.4 % were shown. The high removal efficiencies are attributed to the effective binding of the functional groups from the selected monomers with cations, anions, and oil emulsions.

  11. Recent Improvements in Micromodel Experimentation and Pore-scale Simulation of Multiphase Systems

    NASA Astrophysics Data System (ADS)

    Oostrom, M.; Tartakovsky, A. M.; Grate, J. W.

    2013-12-01

    Recent efforts in the Environmental Molecular Sciences Laboratory at PNNL have resulted in improved experimental methods to fabricate silicon micromodels with different wettability and improved numerical methods to predict multiphase fluid displacement at the pore scale. Wettability is a key parameter influencing capillary pressures, permeabilities, fingering mechanisms, and saturations in multiphase flow processes within porous media. Glass-covered silicon micromodels provide precise structures in which pore-scale displacement processes can be visualized. The wettability of silicon and glass surfaces can be modified by silanization. However, similar treatments of glass and silica surfaces using the same silane do not necessarily yield the same wettability as determined by the oil-water contact angle. Surface wettability modifications and cleaning pretreatments were investigated to determine conditions that yield oil-wet surfaces on glass with similar wettability to silica surfaces treated with the same silane. Both air-water and oil-water contact angles were determined. Displacement experiments completed in these micromodels have shown unstable and stable displacement patterns, related to capillary and viscosity ratios of the fluids. A series of high-resolution numerical experiments were conducted using the Pair-Wise Force Smoothed Particle Hydrodynamics (PF-SPH) multiphase flow model. The novel model was used to simulate experiments that showed viscous fingering, capillary fingering, and stable displacement of immiscible fluids for a wide range of capillary numbers and viscosity ratios. It was demonstrated that the steady state saturation profiles and the boundaries of viscous fingering, capillary fingering, and stable displacement regions compare favorably with micromodel experimental results. For displacing fluid with low viscosity, we observed that the displacement pattern changes from viscous fingering to stable displacement with increasing injection rate

  12. Modeling multiphase migration of organic chemicals in groundwater systems--a review and assessment.

    PubMed Central

    Abriola, L M

    1989-01-01

    Over the past two decades, a number of models have been developed to describe the multiphase migration of organic chemicals in the subsurface. This paper presents the state-of-the-art with regard to such modeling efforts. The mathematical foundations of these models are explored and individual models are presented and discussed. Models are divided into three groups: a) those that assume a sharp interface between the migrating fluids; b) those that incorporate capillarity; and c) those that consider interphase transport of mass. Strengths and weaknesses of each approach are considered along with supporting data for model validation. Future research directions are also highlighted. PMID:2695322

  13. The impact of reservoir conditions and rock heterogeneity on multiphase flow in CO2-brine-sandstone systems

    NASA Astrophysics Data System (ADS)

    Krevor, S. C.; Reynolds, C. A.; Al-Menhali, A.; Niu, B.

    2015-12-01

    Capillary strength and multiphase flow are key for modeling CO2 injection for CO2 storage. Past observations of multiphase flow in this system have raised important questions about the impact of reservoir conditions on flow through effects on wettability, interfacial tension and fluid-fluid mass transfer. In this work we report the results of an investigation aimed at resolving many of these outstanding questions for flow in sandstone rocks. The drainage capillary pressure, drainage and imbibition relative permeability, and residual trapping [1] characteristic curves have been characterized in Bentheimer and Berea sandstone rocks across a pressure range 5 - 20 MPa, temperatures 25 - 90 C and brine salinities 0-5M NaCl. Over 30 reservoir condition core flood tests were performed using techniques including the steady state relative permeability test, the semi-dynamic capillary pressure test, and a new test for the construction of the residual trapping initial-residual curve. Test conditions were designed to isolate effects of interfacial tension, viscosity ratio, density ratio, and salinity. The results of the tests show that, in the absence of rock heterogeneity, reservoir conditions have little impact on flow properties, consistent with continuum scale multiphase flow theory for water wet systems. The invariance of the properties is observed, including transitions of the CO2 from a gas to a liquid to a supercritical fluid, and in comparison with N2-brine systems. Variations in capillary pressure curves are well explained by corresponding changes in IFT although some variation may reflect small changes in wetting properties. The low viscosity of CO2at certain conditions results in sensitivity to rock heterogeneity. We show that (1) heterogeneity is the likely source of uncertainty around past relative permeability observations and (2) that appropriate scaling of the flow potential by a quantification of capillary heterogeneity allows for the selection of core flood

  14. Using statistical learning to close two-fluid multiphase flow equations for a simple bubbly system

    NASA Astrophysics Data System (ADS)

    Ma, Ming; Lu, Jiacai; Tryggvason, Gretar

    2015-09-01

    Direct numerical simulations of bubbly multiphase flows are used to find closure terms for a simple model of the average flow, using Neural Networks (NNs). The flow considered consists of several nearly spherical bubbles rising in a periodic domain where the initial vertical velocity and the average bubble density are homogeneous in two directions but non-uniform in one of the horizontal directions. After an initial transient motion the average void fraction and vertical velocity become approximately uniform. The NN is trained on a dataset from one simulation and then used to simulate the evolution of other initial conditions. Overall, the resulting model predicts the evolution of the various initial conditions reasonably well.

  15. Determination of volume fraction in multiphase systems using incomplete pole figures. [X ray diffraction metallography

    NASA Technical Reports Server (NTRS)

    Houska, C. R.; Rao, V.

    1978-01-01

    The determination of the volume fraction of a second phase in a multiphase sample by X-ray diffraction becomes more difficult if the diffracting planes have a preferred orientation. Lopata and Kula have described a method of treating this problem using complete pole figures for each of the phases. With some samples, it is not always possible or convenient to obtain data over the full hemisphere. Equations and an example are given which require X-ray data over a limited range of approximately 0 to 75 deg. This can be obtained by reflection without a specially cut sample or transmission data. A series of Legendre polynomials are fitted to data collected while spinning the sample about its normal. An extrapolation is made possible by introducing two conditions on the end points which must be satisfied if the extrapolation functions are to be valid.

  16. HEAT TRANSFER ANALYSIS FOR ION-EXCHANGE COLUMN SYSTEM

    SciTech Connect

    Lee, S.; King, W.

    2011-05-23

    Models have been developed to simulate the thermal characteristics of Crystalline Silicotitanate (CST) ion exchange media fully loaded with radioactive cesium in a column configuration and distributed within a waste storage tank. This work was conducted to support the Small Column Ion Exchange (SCIX) program which is focused on processing dissolved, high-sodium salt waste for the removal of specific radionuclides (including Cs-137, Sr-90, and actinides) within a High Level Waste (HLW) storage tank at the Savannah River Site. The SCIX design includes CST columns inserted and supported in the tank top risers for cesium removal. Temperature distributions and maximum temperatures across the column were calculated with a focus on process upset conditions. A two-dimensional computational modeling approach for the in-column ion-exchange domain was taken to include conservative, bounding estimates for key parameters such that the results would provide the maximum centerline temperatures achievable under the design configurations using a feed composition known to promote high cesium loading on CST. The current full-scale design for the CST column includes one central cooling pipe and four outer cooling tubes. Most calculations assumed that the fluid within the column was stagnant (i.e. no buoyancy-induced flow) for a conservative estimate. A primary objective of these calculations was to estimate temperature distributions across packed CST beds immersed in waste supernate or filled with dry air under various accident scenarios. Accident scenarios evaluated included loss of salt solution flow through the bed, inadvertent column drainage, and loss of active cooling in the column. The modeling results demonstrate that the baseline design using one central and four outer cooling tubes provides a highly efficient cooling mechanism for reducing the maximum column temperature.

  17. Noble gas and hydrocarbon tracers in multiphase unconventional hydrocarbon systems: Toward integrated advanced reservoir simulators

    NASA Astrophysics Data System (ADS)

    Darrah, T.; Moortgat, J.; Poreda, R. J.; Muehlenbachs, K.; Whyte, C. J.

    2015-12-01

    Although hydrocarbon production from unconventional energy resources has increased dramatically in the last decade, total unconventional oil and gas recovery from black shales is still less than 25% and 9% of the totals in place, respectively. Further, the majority of increased hydrocarbon production results from increasing the lengths of laterals, the number of hydraulic fracturing stages, and the volume of consumptive water usage. These strategies all reduce the economic efficiency of hydrocarbon extraction. The poor recovery statistics result from an insufficient understanding of some of the key physical processes in complex, organic-rich, low porosity formations (e.g., phase behavior, fluid-rock interactions, and flow mechanisms at nano-scale confinement and the role of natural fractures and faults as conduits for flow). Noble gases and other hydrocarbon tracers are capably of recording subsurface fluid-rock interactions on a variety of geological scales (micro-, meso-, to macro-scale) and provide analogs for the movement of hydrocarbons in the subsurface. As such geochemical data enrich the input for the numerical modeling of multi-phase (e.g., oil, gas, and brine) fluid flow in highly heterogeneous, low permeability formations Herein we will present a combination of noble gas (He, Ne, Ar, Kr, and Xe abundances and isotope ratios) and molecular and isotopic hydrocarbon data from a geographically and geologically diverse set of unconventional hydrocarbon reservoirs in North America. Specifically, we will include data from the Marcellus, Utica, Barnett, Eagle Ford, formations and the Illinois basin. Our presentation will include geochemical and geological interpretation and our perspective on the first steps toward building an advanced reservoir simulator for tracer transport in multicomponent multiphase compositional flow (presented separately, in Moortgat et al., 2015).

  18. Extension of the system constants database for open-tubular columns: system maps at low and intermediate temperatures for four new columns.

    PubMed

    Atapattu, Sanka N; Eggers, Kimberly; Poole, Colin F; Kiridena, Waruna; Koziol, Wladyslaw W

    2009-03-06

    The solvation parameter model is used to characterize the separation properties of four open-tubular columns for gas chromatography at low and intermediate column temperatures covering the range 60-240 degrees C. Solute descriptors for compounds suitable for characterizing columns over the intermediate temperature range are optimized using an iterative procedure. These compounds, and those previously recommended for the lower temperature range, are used to provide system constant maps for Rxi-5Sil MS, Rxi-17, Rtx-TNT and Rtx-TNT2 columns suitable for merging with a system constants database with entries for more than 50 columns. The Rxi-5Sil MS column is shown to have separation properties similar to the silphenylene-dimethylsiloxane copolymer stationary phase (DB-5ms) but these two columns are not selectivity equivalent. The Rxi-17 column has similar separation properties to the Rxi-50 column but is not selectivity equivalent to it. Rxi-17 is a poly(dimethyldiphenylsiloxane) stationary phase containing 50% diphenylsiloxane monomer and Rxi-50 a poly(methylphenylsiloxane) stationary phase with the same nominal composition but a different monomer structure. The difference in monomer structure results in only small changes in selectivity, and for all but the most demanding separations, the columns are interchangeable. The application-specific column (energetic materials) Rtx-TNT is shown to be selectivity equivalent to columns coated with the poly(dimethyldiphenylsiloxane) stationary phases containing 5% diphenylsiloxane monomer. The Rtx-TNT2 column is selectivity equivalent to the proprietary Rtx-OPPesticides column. Rtx-OPPesticides is a low bleed stationary phase, possibly based on silarylene-siloxane chemistry, with a composition designed to mimic the separation properties of the poly(dimethylmethyltrifluoropropylsiloxane) stationary phases containing 35% methyltrifluoropropylsiloxane monomer. Selectivity equivalence of columns is determined by the statistical

  19. Mechanical end joint system for connecting structural column elements

    NASA Technical Reports Server (NTRS)

    Bush, Harold G. (Inventor); Mikulas, Martin M., Jr. (Inventor); Wallsom, Richard E. (Inventor)

    1990-01-01

    A mechanical end joint system is presented that eliminates the possibility of free movements between the joint halves during loading or vibration. Both node joint body (NJB) and column end joint body (CEJB) have cylindrical engaging ends. Each of these ends has an integral semicircular tongue and groove. The two joint halves are engaged transversely - the tongue of the NJB mating with the groove of the CEJB and vice versa. The joint system employs a spring loaded internal latch mechanism housed in the CEJB. During mating, this mechanism is pushed away from the NJB and enters the NJB when mating is completed. In order to lock the joint and add a preload across the tongue and groove faces, an operating ring collar is rotated through 45 deg causing an internal mechanism to compress a Belleville washer preload mechanism. This causes an equal and opposite force to be exerted on the latch bolt and the latch plunger. This force presses the two joint halves tightly together. In order to prevent inadvertent disassembly, a secondary lock is also engaged when the joint is closed. Plungers are carried in the operating ring collar. When the joint is closed, the plungers fall into tracks on the CEJB, which allows the joint to be opened only when the operating ring collar and plungers are pushed directly away from the joining end. One application of this invention is the rapid assembly and disassembly of diverse skeletal framework structures which is extremely important in many projects involving the exploration of space.

  20. Quantitative tomographic measurements of opaque multiphase flows

    SciTech Connect

    GEORGE,DARIN L.; TORCZYNSKI,JOHN R.; SHOLLENBERGER,KIM ANN; O'HERN,TIMOTHY J.; CECCIO,STEVEN L.

    2000-03-01

    An electrical-impedance tomography (EIT) system has been developed for quantitative measurements of radial phase distribution profiles in two-phase and three-phase vertical column flows. The EIT system is described along with the computer algorithm used for reconstructing phase volume fraction profiles. EIT measurements were validated by comparison with a gamma-densitometry tomography (GDT) system. The EIT system was used to accurately measure average solid volume fractions up to 0.05 in solid-liquid flows, and radial gas volume fraction profiles in gas-liquid flows with gas volume fractions up to 0.15. In both flows, average phase volume fractions and radial volume fraction profiles from GDT and EIT were in good agreement. A minor modification to the formula used to relate conductivity data to phase volume fractions was found to improve agreement between the methods. GDT and EIT were then applied together to simultaneously measure the solid, liquid, and gas radial distributions within several vertical three-phase flows. For average solid volume fractions up to 0.30, the gas distribution for each gas flow rate was approximately independent of the amount of solids in the column. Measurements made with this EIT system demonstrate that EIT may be used successfully for noninvasive, quantitative measurements of dispersed multiphase flows.

  1. AOI 1— COMPUTATIONAL ENERGY SCIENCES:MULTIPHASE FLOW RESEARCH High-fidelity multi-phase radiation module for modern coal combustion systems

    SciTech Connect

    Modest, Michael

    2013-11-15

    The effects of radiation in particle-laden flows were the object of the present research. The presence of particles increases optical thickness substantially, making the use of the “optically thin” approximation in most cases a very poor assumption. However, since radiation fluxes peak at intermediate optical thicknesses, overall radiative effects may not necessarily be stronger than in gas combustion. Also, the spectral behavior of particle radiation properties is much more benign, making spectral models simpler (and making the assumption of a gray radiator halfway acceptable, at least for fluidized beds when gas radiation is not large). On the other hand, particles scatter radiation, making the radiative transfer equation (RTE) much more di fficult to solve. The research carried out in this project encompassed three general areas: (i) assessment of relevant radiation properties of particle clouds encountered in fluidized bed and pulverized coal combustors, (ii) development of proper spectral models for gas–particulate mixtures for various types of two-phase combustion flows, and (iii) development of a Radiative Transfer Equation (RTE) solution module for such applications. The resulting models were validated against artificial cases since open literature experimental data were not available. The final models are in modular form tailored toward maximum portability, and were incorporated into two research codes: (i) the open-source CFD code OpenFOAM, which we have extensively used in our previous work, and (ii) the open-source multi-phase flow code MFIX, which is maintained by NETL.

  2. Composite multiphase groundwater model

    SciTech Connect

    Kim, Joon Hyun.

    1989-01-01

    A general comprehensive mathematical model using the composite multi-phase approach to describe groundwater flow and pollution was developed. The comprehensive governing equation was derived from the simple mass balance of chemical species over all the phases in schematic elementary volume, and traditional ground water governing equations are explained from it. An attempt was made to include the complicated aspects of physical chemical and biological processes such as mass fraction, compressibility, capillarity, dispersion, gravity, relative permeability, viscosity, sorption, interfacial mass change and chemical and biological reactions. To make the analysis possible, assumptions have been made for continuous flow of each phase and instantaneous equilibrium for partition. The resulting system of nonlinear governing and constitutive equations was solved numerically. To handle the irregular geometry, complex boundary conditions and many different governing equations with simple modifications, the upstream weighted finite element method was adopted. By using the dynamic allocation of arrays, the code is flexible to work on an IBM 3090 Vector Facility, workstations and PC's for one, two and three dimensional problems. To reduce the computation time and storage requirements, decoupling of the system equations, banded global matrix and vector and parallel processing were used. The program was structured to facilitate inclusion of additional future constitutive equations. To demonstrate the model's versatility, several hypothetical problems were simulated: unsaturated flow through an embankment; one and two dimensional solute transport; one, two, three dimensional multiphase flow; composite multiphase flow and contaminant migration. The instability and convergence criteria of the nonlinear problems were studied. Parameter dependency of the model was also studied.

  3. Thermal analysis for ion-exchange column system

    SciTech Connect

    Lee, S. Y.; King, W. D.

    2012-07-01

    Models have been developed to simulate the thermal characteristics of Crystalline Silico-titanate (CST) ion exchange media fully loaded with radioactive cesium in a column configuration and distributed within a waste storage tank. This work was conducted to support the Small Column Ion Exchange (SCIX) program which is focused on processing dissolved, high-sodium salt waste for the removal of specific radionuclides (including Cs-137, Sr-90, and actinides) within a High Level Waste (HLW) storage tank at the Savannah River Site. A two-dimensional computational modeling approach for the in-column ion-exchange domain was taken to include conservative, bounding estimates for key parameters such that the results would provide the maximum centerline temperatures achievable under the design configurations using a feed composition known to promote high cesium loading on CST. A primary objective of these calculations was to estimate temperature distributions across packed CST beds immersed in waste supernate or filled with dry air under various accident scenarios. Accident scenarios evaluated included loss of salt solution flow through the bed, inadvertent column drainage, and loss of active cooling in the column. The modeling results demonstrate that the baseline design using one central and four outer cooling tubes provides a highly efficient cooling mechanism for reducing the maximum column temperature. (authors)

  4. E-beam exposure system using multi column cell (MCC) with CP for mask writing

    NASA Astrophysics Data System (ADS)

    Yamada, Akio; Yasuda, Hiroshi; Yamabe, Masaki

    2008-10-01

    In the Mask D2I project at ASET, the authors designed a novel electron beam exposure system using the concepts of MCC (multi column cell), CP (character projection), and VSB (variable shaped beam) to improve the throughput of electron beam exposure systems. They presented outlines of a proof-of-concept system of MCC, and have shown the performances of VSB and CP in the system. They evaluated the impacts on beam position in one column cell caused by deflections in another column cell. The impacts were found to be less than 0.1nm in presence of major deflections in the neighboring column cell. Hence it was concluded that there was no noticeable impact on deflections cause by the neighboring column cells in the MCC system.

  5. Slurry bubble column hydrodynamics

    NASA Astrophysics Data System (ADS)

    Rados, Novica

    Slurry bubble column reactors are presently used for a wide range of reactions in both chemical and biochemical industry. The successful design and scale up of slurry bubble column reactors require a complete understanding of multiphase fluid dynamics, i.e. phase mixing, heat and mass transport characteristics. The primary objective of this thesis is to improve presently limited understanding of the gas-liquid-solid slurry bubble column hydrodynamics. The effect of superficial gas velocity (8 to 45 cm/s), pressure (0.1 to 1.0 MPa) and solids loading (20 and 35 wt.%) on the time-averaged solids velocity and turbulent parameter profiles has been studied using Computer Automated Radioactive Particle Tracking (CARPT). To accomplish this, CARPT technique has been significantly improved for the measurements in highly attenuating systems, such as high pressure, high solids loading stainless steel slurry bubble column. At a similar set of operational conditions time-averaged gas and solids holdup profiles have been evaluated using the developed Computed Tomography (CT)/Overall gas holdup procedure. This procedure is based on the combination of the CT scans and the overall gas holdup measurements. The procedure assumes constant solids loading in the radial direction and axially invariant cross-sectionally averaged gas holdup. The obtained experimental holdup, velocity and turbulent parameters data are correlated and compared with the existing low superficial gas velocities and atmospheric pressure CARPT/CT gas-liquid and gas-liquid-solid slurry data. The obtained solids axial velocity radial profiles are compared with the predictions of the one dimensional (1-D) liquid/slurry recirculation phenomenological model. The obtained solids loading axial profiles are compared with the predictions of the Sedimentation and Dispersion Model (SDM). The overall gas holdup values, gas holdup radial profiles, solids loading axial profiles, solids axial velocity radial profiles and solids

  6. Thermodynamic approach to the stability of multi-phase systems. Application to the Y2O3–Fe system

    DOE PAGES

    Samolyuk, German D.; Osetskiy, Yury N.

    2015-07-07

    Oxide-metal systems (OMSs) are important in many practical applications, and therefore, are under extensive studies using a wide range of techniques. The most accurate theoretical approaches are based on density functional theory (DFT), which are limited to ~102 atoms. Multi-scale approaches, e.g., DFT+Monte Carlo, are often used to model OMSs at the atomic level. These approaches can describe qualitatively the kinetics of some processes but not the overall stability of OMSs. In this paper, we propose a thermodynamic approach to study equilibrium in multiphase systems, which can be sequentially enhanced by considering different defects and microstructures. We estimate the thermodynamicmore » equilibrium by minimization the free energy of the whole multiphase system using a limited set of defects and microstructural objects for which the properties are calculated by DFT. As an example, we consider Y2O3+bcc Fe with vacancies in both the Y2O3 and bcc Fe phases, Y substitutions and O interstitials in Fe, Fe impurities and antisite defects in Y2O3. The output of these calculations is the thermal equilibrium concentration of all the defects for a particular temperature and composition. The results obtained confirmed the high temperature stability of yttria in iron. As a result, model development towards more accurate calculations is discussed.« less

  7. Thermodynamic approach to the stability of multi-phase systems. Application to the Y2O3–Fe system

    SciTech Connect

    Samolyuk, German D.; Osetskiy, Yury N.

    2015-07-07

    Oxide-metal systems (OMSs) are important in many practical applications, and therefore, are under extensive studies using a wide range of techniques. The most accurate theoretical approaches are based on density functional theory (DFT), which are limited to ~102 atoms. Multi-scale approaches, e.g., DFT+Monte Carlo, are often used to model OMSs at the atomic level. These approaches can describe qualitatively the kinetics of some processes but not the overall stability of OMSs. In this paper, we propose a thermodynamic approach to study equilibrium in multiphase systems, which can be sequentially enhanced by considering different defects and microstructures. We estimate the thermodynamic equilibrium by minimization the free energy of the whole multiphase system using a limited set of defects and microstructural objects for which the properties are calculated by DFT. As an example, we consider Y2O3+bcc Fe with vacancies in both the Y2O3 and bcc Fe phases, Y substitutions and O interstitials in Fe, Fe impurities and antisite defects in Y2O3. The output of these calculations is the thermal equilibrium concentration of all the defects for a particular temperature and composition. The results obtained confirmed the high temperature stability of yttria in iron. As a result, model development towards more accurate calculations is discussed.

  8. Pore-scale modeling of multiphase reactive transport with phase transitions and dissolution-precipitation processes in closed systems.

    PubMed

    Chen, Li; Kang, Qinjun; Robinson, Bruce A; He, Ya-Ling; Tao, Wen-Quan

    2013-04-01

    A pore-scale model based on the lattice Boltzmann (LB) method is developed for multiphase reactive transport with phase transitions and dissolution-precipitation processes. The model combines the single-component multiphase Shan-Chen LB model [X. Shan and H. Chen, Phys. Rev. E 47, 1815 (1993)], the mass transport LB model [S. P. Sullivan et al., Chem. Eng. Sci. 60, 3405 (2005)], and the dissolution-precipitation model [Q. Kang et al., J. Geophys. Res. 111, B05203 (2006)]. Care is taken to handle information on computational nodes undergoing solid-liquid or liquid-vapor phase changes to guarantee mass and momentum conservation. A general LB concentration boundary condition is proposed that can handle various concentration boundaries including reactive and moving boundaries with complex geometries. The pore-scale model can capture coupled nonlinear multiple physicochemical processes including multiphase flow with phase separations, mass transport, chemical reactions, dissolution-precipitation processes, and dynamic evolution of the pore geometries. The model is validated using several multiphase flow and reactive transport problems and then used to study the thermal migration of a brine inclusion in a salt crystal. Multiphase reactive transport phenomena with phase transitions between liquid-vapor phases and dissolution-precipitation processes of the salt in the closed inclusion are simulated and the effects of the initial inclusion size and temperature gradient on the thermal migration are investigated.

  9. A Linearized Model for Wave Propagation through Coupled Volcanic Conduit-crack Systems Filled with Multiphase Magma

    NASA Astrophysics Data System (ADS)

    Liang, C.; Dunham, E. M.; OReilly, O. J.; Karlstrom, L.

    2015-12-01

    Both the oscillation of magma in volcanic conduits and resonance of fluid-filled cracks (dikes and sills) are appealing explanations for very long period signals recorded at many active volcanoes. While these processes have been studied in isolation, real volcanic systems involve interconnected networks of conduits and cracks. The overall objective of our work is to develop a model of wave propagation and ultimately eruptive fluid dynamics through this coupled system. Here, we present a linearized model for wave propagation through a conduit with multiple cracks branching off of it. The fluid is compressible and viscous, and is comprised of a mixture of liquid melt and gas bubbles. Nonequilibrium bubble growth and resorption (BGR) is quantified by introducing a time scale for mass exchange between phases, following the treatment in Karlstrom and Dunham (2015). We start by deriving the dispersion relation for crack waves travelling along the multiphase-magma-filled crack embedded in an elastic solid. Dissipation arises from magma viscosity, nonequilibrium BGR, and radiation of seismic waves into the solid. We next introduce coupling conditions between the conduit and crack, expressing conservation of mass and the balance of forces across the junction. Waves in the conduit, like those in the crack, are influenced by nonequilibrium BGR, but the deformability of the surrounding solid is far less important than for cracks. Solution of the coupled system of equations provides the evolution of pressure and fluid velocity within the conduit-crack system. The system has various resonant modes that are sensitive to fluid properties and to the geometry of the conduit and cracks. Numerical modeling of seismic waves in the solid allows us to generate synthetic seismograms.

  10. Reactive transport modeling of stable carbon isotope fractionation in a multi-phase multi-component system during carbon sequestration

    SciTech Connect

    Zhang, Shuo; DePaolo, Donald J.; Zheng, Liange; Mayer, Bernhard

    2014-12-31

    Carbon stable isotopes can be used in characterization and monitoring of CO2 sequestration sites to track the migration of the CO2 plume and identify leakage sources, and to evaluate the chemical reactions that take place in the CO2-water-rock system. However, there are few tools available to incorporate stable isotope information into flow and transport codes used for CO2 sequestration problems. We present a numerical tool for modeling the transport of stable carbon isotopes in multiphase reactive systems relevant to geologic carbon sequestration. The code is an extension of the reactive transport code TOUGHREACT. The transport module of TOUGHREACT was modified to include separate isotopic species of CO2 gas and dissolved inorganic carbon (CO2, CO32-, HCO3-,…). Any process of transport or reaction influencing a given carbon species also influences its isotopic ratio. Isotopic fractionation is thus fully integrated within the dynamic system. The chemical module and database have been expanded to include isotopic exchange and fractionation between the carbon species in both gas and aqueous phases. The performance of the code is verified by modeling ideal systems and comparing with theoretical results. Efforts are also made to fit field data from the Pembina CO2 injection project in Canada. We show that the exchange of carbon isotopes between dissolved and gaseous carbon species combined with fluid flow and transport, produce isotopic effects that are significantly different from simple two-component mixing. These effects are important for understanding the isotopic variations observed in field demonstrations.

  11. Reactive transport modeling of stable carbon isotope fractionation in a multi-phase multi-component system during carbon sequestration

    DOE PAGES

    Zhang, Shuo; DePaolo, Donald J.; Zheng, Liange; ...

    2014-12-31

    Carbon stable isotopes can be used in characterization and monitoring of CO2 sequestration sites to track the migration of the CO2 plume and identify leakage sources, and to evaluate the chemical reactions that take place in the CO2-water-rock system. However, there are few tools available to incorporate stable isotope information into flow and transport codes used for CO2 sequestration problems. We present a numerical tool for modeling the transport of stable carbon isotopes in multiphase reactive systems relevant to geologic carbon sequestration. The code is an extension of the reactive transport code TOUGHREACT. The transport module of TOUGHREACT was modifiedmore » to include separate isotopic species of CO2 gas and dissolved inorganic carbon (CO2, CO32-, HCO3-,…). Any process of transport or reaction influencing a given carbon species also influences its isotopic ratio. Isotopic fractionation is thus fully integrated within the dynamic system. The chemical module and database have been expanded to include isotopic exchange and fractionation between the carbon species in both gas and aqueous phases. The performance of the code is verified by modeling ideal systems and comparing with theoretical results. Efforts are also made to fit field data from the Pembina CO2 injection project in Canada. We show that the exchange of carbon isotopes between dissolved and gaseous carbon species combined with fluid flow and transport, produce isotopic effects that are significantly different from simple two-component mixing. These effects are important for understanding the isotopic variations observed in field demonstrations.« less

  12. Thermodynamics and Mass Transport in Multicomponent, Multiphase H2O Systems of Planetary Interest

    NASA Astrophysics Data System (ADS)

    Lu, Xinli; Kieffer, Susan W.

    2009-05-01

    Heat and mass transport in low-temperature, low-pressure H2O systems are important processes on Earth, and on a number of planets and moons in the Solar System. In most occurrences, these systems will contain other components, the so-called noncondensible gases, such as CO2, CO, SO2, CH4, and N2. The presence of the noncondensible components can greatly alter the thermodynamic properties of the phases and their flow properties as they move in and on the planets. We review various forms of phase diagrams that give information about pressure-temperature-volume-entropy-enthalpy-composition conditions in these complex systems. Fluid dynamic models must be coupled to the thermodynamics to accurately describe flow in gas-driven liquid and solid systems. The concepts are illustrated in detail by considering flow and flow instabilities such as geysering in modern geothermal systems on Earth, paleofluid systems on Mars, and cryogenic ice-gas systems on Mars and Enceladus. We emphasize that consideration of single-component end-member systems often leads to conclusions that exclude many qualitatively and quantitatively important phenomena.

  13. Dynamic behavior of chemical exchange column in a water detritiation system for a fusion reactor

    SciTech Connect

    Yamanishi, T.; Iwai, Y.

    2008-07-15

    The dynamic behavior of a CECE column used for a demonstration reactor (DEMO) plant has been studied. In the case where the column was filled with natural water, the time required to achieve steady state was almost the same as that for the column operated under the total reflux mode. The manipulated variables were flow rate of the bottom stream for the control of the bottom tritium concentration, and flow rate of the hydrogen stream for the control of the top tritium concentration. For both the variables, the response curve was expressed by the first-order lag system, and a PID controller could be applied. (authors)

  14. Complex Equilibrium Calculations of Nonideal Multiphase Systems (CEC- NMS) and Applications to Liquid Metal Fuel Combustion

    DTIC Science & Technology

    1989-03-15

    Underwater Propulsion System," Proceedings of Tenth Intersociety Energy Conference. pp. 1023-1030. Besmann, T. M. (1977), " SOLGASMIX - PV , A Computer...than 400 chemical species over a temperature range of 300 to 5000 K is provided. Another popular computer program is SOLGASMIX (Ericksson 1971, 1973...variable is called the enthalpy (H): H = H(S, P, Ni t N2, .... Nn) (2.14) also H = U + PV (2.15) The enthalpy of a system at constant pressure is

  15. Integrated null-flux suspension and multiphase propulsion system for magnetically-levitated vehicles

    DOEpatents

    Rote, Donald M.; He, Jianliang; Johnson, Larry R.

    1994-01-01

    A propulsion and stabilization system comprising a series of FIG. 8 coils mounted vertically on the walls of the guideway to provide suspension, lateral guidance and propulsion of a magnetically levitated vehicle. This system further allows for altering the magnetic field effects by changing the relative position of the loops comprising the FIG. 8 coils either longitudinally and/or vertically with resulting changes in the propulsion, the vertical stability, and the suspension.

  16. Integrated null-flux suspension and multiphase propulsion system for magnetically-levitated vehicles

    DOEpatents

    Rote, D.M.; He, J.; Johnson, L.R.

    1994-01-04

    A propulsion and stabilization system are described comprising a series of coils mounted vertically on the walls of the guideway to provide suspension, lateral guidance, and propulsion of a magnetically levitated vehicle. This system further allows for altering the magnetic field effects by changing the relative position of the loops comprising the coils either longitudinally and/or vertically with resulting changes in the propulsion, the vertical stability, and the suspension. 8 figures.

  17. Integrated null-flux suspension and multiphase propulsion system for magnetically-levitated vehicles

    DOEpatents

    Rote, D.M.; He, Jianliang; Johnson, L.R.

    1992-01-01

    This report discusses a propulsion and stabilization system comprising a series of figure 8 coils mounted vertically on the walls of the guideway to provide suspension, lateral guidance and propulsion of a magnetically levitated vehicle. This system further allows for altering the magnetic field effects by changing the relative position of the loops comprising the figure 8 coils either longitudinally and/or vertically with resulting changes in the propulsion, the vertical stability, and the suspension.

  18. Supervising and Controlling Unmanned Systems: A Multi-Phase Study with Subject Matter Experts

    PubMed Central

    Porat, Talya; Oron-Gilad, Tal; Rottem-Hovev, Michal; Silbiger, Jacob

    2016-01-01

    Proliferation in the use of Unmanned Aerial Systems (UASs) in civil and military operations has presented a multitude of human factors challenges; from how to bridge the gap between demand and availability of trained operators, to how to organize and present data in meaningful ways. Utilizing the Design Research Methodology (DRM), a series of closely related studies with subject matter experts (SMEs) demonstrate how the focus of research gradually shifted from “how many systems can a single operator control” to “how to distribute missions among operators and systems in an efficient way”. The first set of studies aimed to explore the modal number, i.e., how many systems can a single operator supervise and control. It was found that an experienced operator can supervise up to 15 UASs efficiently using moderate levels of automation, and control (mission and payload management) up to three systems. Once this limit was reached, a single operator's performance was compared to a team controlling the same number of systems. In general, teams led to better performances. Hence, shifting design efforts toward developing tools that support teamwork environments of multiple operators with multiple UASs (MOMU). In MOMU settings, when the tasks are similar or when areas of interest overlap, one operator seems to have an advantage over a team who needs to collaborate and coordinate. However, in all other cases, a team was advantageous over a single operator. Other findings and implications, as well as future directions for research are discussed. PMID:27252662

  19. Effect of concentration dependence of the diffusion coefficient on homogenization kinetics in multiphase binary alloy systems

    NASA Technical Reports Server (NTRS)

    Tenney, D. R.; Unnam, J.

    1978-01-01

    Diffusion calculations were performed to establish the conditions under which concentration dependence of the diffusion coefficient was important in single, two, and three phase binary alloy systems. Finite-difference solutions were obtained for each type of system using diffusion coefficient variations typical of those observed in real alloy systems. Solutions were also obtained using average diffusion coefficients determined by taking a logarithmic average of each diffusion coefficient variation considered. The constant diffusion coefficient solutions were used as reference in assessing diffusion coefficient variation effects. Calculations were performed for planar, cylindrical, and spherical geometries in order to compare the effect of diffusion coefficient variations with the effect of interface geometries. In most of the cases considered, the diffusion coefficient of the major-alloy phase was the key parameter that controlled the kinetics of interdiffusion.

  20. An update on subsea multiphase pumping

    SciTech Connect

    Colombi, P.; De Donno, S.

    1996-02-01

    Agip SpA anticipates that subsea multiphase production, based on long-distance transportation of untreated oilwell fluids--namely, oil, water, and gas, will be an efficient tool for the exploitation of deepwater and marginal fields. In 1990, at the Trecate onshore oil field, Agip completed long-term testing of a multiphase screw pump, which confirmed commercial surface applications. Agip then integrated a subsea version of an improved multiphase twin-screw pump into a subsea multiphase boosting unit that was installed at the Prezioso field, offshore Sicily, in 1994 That was the first subsea installation of an electrically driven multi-phase pump operating with live oil. Agip began endurance testing of the pumping system in January 1995 and by last November, the cumulated period of running reached 3,500 hours with no evidence of pump-capacity reduction. Testing focused on boosting at high gas-void fraction and oil viscosity, operation at variable motor speed for pump control, pump control by means of throttling valves, direct interaction of the pumping system with both wells and the multiphase export line, variation of the lube-oil pressure across seals and bearings, and the evaluation of any degradation effect on the pump flow capacity over time. This paper reviews the design and performance of this pump and applicability to other offshore projects.

  1. Selecting multiphase pumps

    SciTech Connect

    Prang, A.J.

    1997-02-01

    Multiphase pumps in petroleum applications today must handle liquid products containing large amounts of gas, and often including water and sand as well. In the past, gas was commonly separated and flared off at the well head, and only liquid product was piped along for further processing. Using this setup, processing the gas as well as the liquid requires separators, compressors and dual pipelines. Rotary two-screw units are ideal for multiphase use, as they can pump any product that can be introduced into the suction passages of their screws. These devices also effectively handle heat generation from compressed gases. To select units for multiphase applications, an engineer should be familiar with these pumps and how they work. This article discusses rotary-screw pumps and how to effectively select a unit for multiphase service.

  2. Zero-derivative boundary condition for pulsed distributed systems. [column chromatography example

    NASA Technical Reports Server (NTRS)

    Lashmet, P. K.; Woodrow, P. T.

    1975-01-01

    To permit use of experimentally determined Peclet numbers in numerical simulations of pulsed distributed flow systems such as chromatograph columns, substitution of the zero-derivative boundary condition for the infinite boundary condition used in treating data is examined. Moment analysis shows that application of the zero-derivative condition external to the column will yield equivalent numerical results for the two boundary conditions. Criteria for locating this position are provided as a function of the Peclet number.

  3. Present status of multi-column cell exposure system for mask writing

    NASA Astrophysics Data System (ADS)

    Yasuda, Hiroshi; Yamada, Akio; Yamabe, Masaki

    2009-04-01

    In the Mask D2I project at ASET, we are developing a novel electron beam exposure system using the concepts of MCC (multi column cell), CP (character projection), and VSB (variable shaped beam) to improve the throughput of electron beam exposure systems. In this paper we present the outline of a proof-of-concept system of MCC, results of the evaluation of fundamental functions of the system, and early writing results including multi column stitching. In the evaluation of fundamental functions of the system, we found that there is no interference on beam positions among the CCs, and that the beam position stability is quite good. In our early writing experiments, we had presented the first writing result of MCC and the first stitching result of a multi column system ever reported.

  4. Computational Modeling of Multiphase Reactors.

    PubMed

    Joshi, J B; Nandakumar, K

    2015-01-01

    Multiphase reactors are very common in chemical industry, and numerous review articles exist that are focused on types of reactors, such as bubble columns, trickle beds, fluid catalytic beds, etc. Currently, there is a high degree of empiricism in the design process of such reactors owing to the complexity of coupled flow and reaction mechanisms. Hence, we focus on synthesizing recent advances in computational and experimental techniques that will enable future designs of such reactors in a more rational manner by exploring a large design space with high-fidelity models (computational fluid dynamics and computational chemistry models) that are validated with high-fidelity measurements (tomography and other detailed spatial measurements) to provide a high degree of rigor. Understanding the spatial distributions of dispersed phases and their interaction during scale up are key challenges that were traditionally addressed through pilot scale experiments, but now can be addressed through advanced modeling.

  5. The General Form of the Gibbs-Duhem Equation for Multiphase/Multicomponent Systems and Its Application to Solid-State Activity Measurements

    NASA Astrophysics Data System (ADS)

    Sacchetti, Mark

    2001-02-01

    The general form of the Gibbs-Duhem equation is derived for multiphase/multicomponent thermodynamic systems. The result illustrates that the form of the equation is invariant with respect to the number of phases present in the material. Therefore, calculation of activities or activity coefficients is possible using the same form of equation as has been applied to single-phase systems. The general form of the equation is applied to two organic solids, crystalline albuterol sulfate and amorphous poly(vinyl pyrrolidone). Physical chemistry instructors may find the derivation of the general form of the Gibbs-Duhem equation and its application to pharmaceutical materials a useful exercise for students.

  6. Strong correlation and multi-phase solution in nonequilibrium lattice systems coupled to dissipation medium

    NASA Astrophysics Data System (ADS)

    Han, Jong; Li, Jiajun; Aron, Camille; Kotliar, Gabriel

    2014-03-01

    How does a strongly correlated electronic solid evolve continuously out of equilibrium when an electric field is applied? While this question may seem deceptively simple, it requires rigorous understanding of dissipation. We formulate the nonequilibrium steady-state lattice coupled to fermion baths in the Coulomb gauge. We demonstrate that the Hubbard model solved using the iterative perturbation theory within the dynamical mean-field approximation recovers the DC conductivity independent of the Coulomb interaction in a very narrow linear response regime. Due to the singular dependence of the effective temperature on the damping in the steady-state [2], systems with damping have dramatic field-dependent effect, very different from dissipationless systems. We conclude that the dominant physics in lattice nonequilibrium is not the field vs quasi-particle energy, but rather the Joule heat vs the quasi-particle energy. Furthermore, we show that, in the vicinity of the Mott-insulator transition, the solution supports mixed-phase state scenario which indicates that the electron transport in solids under high-field can be spatially inhomogeneous leading to filamentary conducting paths, as suggested by experiments. Supported by NSF DMR-0907150, NSF DMR-1308141

  7. Fast ion transport in silver halide solid solutions and multiphase systems

    NASA Technical Reports Server (NTRS)

    Shahi, K.; Wagner, J. B., Jr.

    1980-01-01

    The incorporation of homovalent ions, e.g., I(-) in AgBr, leads to a substantial increase in ionic conductivity sigma. The charge compensation concept does not explain the enhancement. AgBr + 30 mol. % AgI exhibits sigma approximately 7/omega/cm at 380 C, which is approximately 170% larger than that of alpha-AgI, the best known superionic conductor, at its melting point. The purely elastic displacement caused by the foreign ion is suggested to be the origin of such a unique behavior. Furthermore, AgI-AgBr two-phase systems display sigma approximately 10 to the 3rd times higher than predicted by the classical theories.

  8. Advanced tomographic flow diagnostics for opaque multiphase fluids

    SciTech Connect

    Torczynski, J.R.; O`Hern, T.J.; Adkins, D.R.; Jackson, N.B.; Shollenberger, K.A.

    1997-05-01

    This report documents the work performed for the ``Advanced Tomographic Flow Diagnostics for Opaque Multiphase Fluids`` LDRD (Laboratory-Directed Research and Development) project and is presented as the fulfillment of the LDRD reporting requirement. Dispersed multiphase flows, particularly gas-liquid flows, are industrially important to the chemical and applied-energy industries, where bubble-column reactors are employed for chemical synthesis and waste treatment. Due to the large range of length scales (10{sup {minus}6}-10{sup 1}m) inherent in real systems, direct numerical simulation is not possible at present, so computational simulations are forced to use models of subgrid-scale processes, the accuracy of which strongly impacts simulation fidelity. The development and validation of such subgrid-scale models requires data sets at representative conditions. The ideal measurement techniques would provide spatially and temporally resolved full-field measurements of the distributions of all phases, their velocity fields, and additional associated quantities such as pressure and temperature. No technique or set of techniques is known that satisfies this requirement. In this study, efforts are focused on characterizing the spatial distribution of the phases in two-phase gas-liquid flow and in three-phase gas-liquid-solid flow. Due to its industrial importance, the bubble-column geometry is selected for diagnostics development and assessment. Two bubble-column testbeds are utilized: one at laboratory scale and one close to industrial scale. Several techniques for measuring the phase distributions at conditions of industrial interest are examined: level-rise measurements, differential-pressure measurements, bulk electrical impedance measurements, electrical bubble probes, x-ray tomography, gamma-densitometry tomography, and electrical impedance tomography.

  9. Investigation of partitioning mechanism for volatile organic compounds in a multiphase system.

    PubMed

    Starokozhev, Elena; Sieg, Karsten; Fries, Elke; Püttmann, Willhelm

    2011-03-01

    Laboratory experiments were performed to investigate the partitioning behavior of a set of diverse volatile organic compounds (VOCs). After equilibration at a temperature of 25°C, the VOC concentrations were measured by headspace method in combination with gas chromatography/mass spectrometry (GC/MS). The obtained data were used to determine the partition coefficients (K(P)) of VOCs in a gas-liguid-solid system. The results have shown that the presence and nature of solid materials in the working solution control the air-water partitioning of dissolved VOCs. The air/solution partitioning of BTEX and C(9)-C(10) aldehydes was most affected in the presence of diesel soot. K(P) values decreased by a factor ranging from 1.5 for toluene to 3.0 for ethylbenzene. The addition of mineral dust in the working solution exhibited greater influence on the partitioning of short aldehydes. K(P) values decreased by a factor of 1.8. The experimental partition coefficients were used to develop a predictive model for partitioning of BTEX and n-aldehydes between air, water and solid phases.

  10. EDITORIAL: Measurement techniques for multiphase flows Measurement techniques for multiphase flows

    NASA Astrophysics Data System (ADS)

    Okamoto, Koji; Murai, Yuichi

    2009-11-01

    Research on multiphase flows is very important for industrial applications, including power stations, vehicles, engines, food processing and so on. Multiphase flows originally have nonlinear features because of multiphase systems. The interaction between the phases plays a very interesting role in the flows. The nonlinear interaction causes the multiphase flows to be very complicated. Therefore techniques for measuring multiphase flows are very useful in helping to understand the nonlinear phenomena. The state-of-the-art measurement techniques were presented and discussed at the sixth International Symposium on Measurement Techniques for Multiphase Flows (ISMTMF2008) held in Okinawa, Japan, on 15-17 December 2008. This special feature of Measurement Science and Technology includes selected papers from ISMTMF2008. Okinawa has a long history as the Ryukyus Kingdom. China, Japan and many western Pacific countries have had cultural and economic exchanges through Okinawa for over 1000 years. Much technical and scientific information was exchanged at the symposium in Okinawa. The proceedings of ISMTMF2008 apart from these special featured papers were published in Journal of Physics: Conference Series vol. 147 (2009). We would like to express special thanks to all the contributors to the symposium and this special feature. This special feature will be a milestone in measurement techniques for multiphase flows.

  11. Multiphase pumps and flow meters avoid platform construction

    SciTech Connect

    Elde, J.

    1999-02-01

    One of the newest wrinkles in efficiency in BP`s Eastern Trough Area Project (ETAP) is the system for moving multiphase oil, water and gas fluids from the Machar satellite field to the Marnock Central Processing Facility (CPF). Using water-turbine-driven multiphase pumps and multiphase flow meters, the system moves fluid with no need for a production platform. In addition, BP has designed the installation so it reduces and controls water coning, thereby increasing recoverable reserves. Both subsea multiphase booster stations (SMUBS) and meters grew out of extensive development work and experience at Framo Engineering AS (Framo) in multiphase meters and multiphase pump systems for subsea installation. Multiphase meter development began in 1990 and the first subsea multiphase meters were installed in the East Spar Project in Australia in 1996. By September 1998, the meters had been operating successfully for more than 1 year. A single multiphase meter installed in Marathon`s West Brae Project has also successfully operated for more than 1 year. Subsea meters for ETAP were installed and began operating in July 1998.

  12. Surface control system for the 15 meter hoop-column antenna

    NASA Technical Reports Server (NTRS)

    Miller, James B.; Ahl, Elvin L., Jr.; Butler, David H.; Peri, Frank, Jr.

    1986-01-01

    The 15-meter hoop-column antenna fabricated by the Harris Corporation under contract to the NASA Langley Research Center is described. The antenna is a deployable and restowable structure consisting of a central telescoping column, a 15-meter-diameter folding hoop, and a mesh reflector surface. The hoop is supported and positioned by 48 quartz cords attached to the column above the hoop, and by 24 graphite cords from the base of the antenna column. The RF reflective surface is a gold plated molybdenum wire mesh supported on a graphite cord truss structure which is attached between the hoop and the column. The surface contour is controlled by 96 graphite cords from the antenna base to the rear of the truss assembly. The antenna is actually a quadaperture reflector with each quadrant of the surface mesh shaped to produce an offset parabolic reflector. Results of near-field and structural tests are given. Controls structures and electromagnetics interaction, surface control system requirements, mesh control adjustment, surface control system actuator assembly, surface control system electronics, the system interface unit, and control stations are discussed.

  13. Diachronous Growth of Normal Fault Systems in Multiphase Rift Basins: Structural Evolution of the East Shetland Basin, Northern North Sea

    NASA Astrophysics Data System (ADS)

    Claringbould, Johan S.; Bell, Rebecca E.; A-L. Jackson, Christopher; Gawthorpe, Robert L.; Odinsen, Tore

    2015-04-01

    Our ability to determine the structural evolution and interaction of fault systems (kinematically linked group of faults that are in the km to 10s of km scale) within a rift basin is typically limited by the spatial extent and temporal resolution of the available data and methods used. Physical and numerical models provide predictions on how fault systems nucleate, grow and interact, but these models need to be tested with natural examples. Although field studies and individual 3D seismic surveys can provide a detailed structural evolution of individual fault systems, they are often spatially limited and cannot be used examine the interaction of fault systems throughout the entire basin. In contrast, regional subsurface studies, commonly conducted on widely spaced 2D seismic surveys, are able to capture the general structural evolution of a rift basin, but lack the spatial and temporal detail. Moreover, these studies typically describe the structural evolution of rifts as comprising multiple discrete tectonic stages (i.e. pre-, syn- and post-rift). This simplified approach does not, however, consider that the timing of activity can be strongly diachronous along and between faults that form part of a kinematically linked system within a rift basin. This study focuses on the East Shetland Basin (ESB), a multiphase rift basin located on the western margin of the North Viking Graben, northern North Sea. Most previous studies suggest the basin evolved in response to two discrete phases of extension in the Permian-Triassic and Middle-Late Jurassic, with the overall geometry of the latter rift to be the result of selective reactivation of faults associated with the former rift. Gradually eastwards thickening intra-rift strata (deposited between two rift phases) that form wedges between and within fault blocks have led to two strongly contrasting tectonic interpretations: (i) Early-Middle Jurassic differential thermal subsidence after Permian-Triassic rifting; or (ii

  14. Water table fluctuations and soil biogeochemistry: An experimental approach using an automated soil column system

    NASA Astrophysics Data System (ADS)

    Rezanezhad, F.; Couture, R.-M.; Kovac, R.; O'Connell, D.; Van Cappellen, P.

    2014-02-01

    Water table fluctuations significantly affect the biological and geochemical functioning of soils. Here, we introduce an automated soil column system in which the water table regime is imposed using a computer-controlled, multi-channel pump connected to a hydrostatic equilibrium reservoir and a water storage reservoir. The potential of this new system is illustrated by comparing results from two columns filled with 45 cm of the same homogenized riparian soil. In one soil column the water table remained constant at -20 cm below the soil surface, while in the other the water table oscillated between the soil surface and the bottom of the column, at a rate of 4.8 cm d-1. The experiment ran for 75 days at room temperature (25 ± 2 °C). Micro-sensors installed at -10 and -30 cm below the soil surface in the stable water table column recorded constant redox potentials on the order of 600 and -200 mV, respectively. In the fluctuating water table column, redox potentials at the same depths oscillated between oxidizing (∼700 mV) and reducing (∼-100 mV) conditions. Pore waters collected periodically and solid-phase analyses on core material obtained at the end of the experiment highlighted striking geochemical differences between the two columns, especially in the time series and depth distributions of Fe, Mn, K, P and S. Soil CO2 emissions derived from headspace gas analysis exhibited periodic variations in the fluctuating water table column, with peak values during water table drawdown. Transient redox conditions caused by the water table fluctuations enhanced microbial oxidation of soil organic matter, resulting in a pronounced depletion of particulate organic carbon in the midsection of the fluctuating water table column. Denaturing Gradient Gel Electrophoresis (DGGE) revealed the onset of differentiation of the bacterial communities in the upper (oxidizing) and lower (reducing) soil sections, although no systematic differences in microbial community structure

  15. Design and Prototype of an Automated Column-Switching HPLC System for Radiometabolite Analysis

    PubMed Central

    Vasdev, Neil; Collier, Thomas Lee

    2016-01-01

    Column-switching high performance liquid chromatography (HPLC) is extensively used for the critical analysis of radiolabeled ligands and their metabolites in plasma. However, the lack of streamlined apparatus and consequently varying protocols remain as a challenge among positron emission tomography laboratories. We report here the prototype apparatus and implementation of a fully automated and simplified column-switching procedure to allow for the easy and automated determination of radioligands and their metabolites in up to 5 mL of plasma. The system has been used with conventional UV and coincidence radiation detectors, as well as with a single quadrupole mass spectrometer. PMID:27548189

  16. Design and Prototype of an Automated Column-Switching HPLC System for Radiometabolite Analysis.

    PubMed

    Vasdev, Neil; Collier, Thomas Lee

    2016-08-17

    Column-switching high performance liquid chromatography (HPLC) is extensively used for the critical analysis of radiolabeled ligands and their metabolites in plasma. However, the lack of streamlined apparatus and consequently varying protocols remain as a challenge among positron emission tomography laboratories. We report here the prototype apparatus and implementation of a fully automated and simplified column-switching procedure to allow for the easy and automated determination of radioligands and their metabolites in up to 5 mL of plasma. The system has been used with conventional UV and coincidence radiation detectors, as well as with a single quadrupole mass spectrometer.

  17. The 15-meter diameter hoop/column antenna surface control actuator system

    NASA Technical Reports Server (NTRS)

    Ahl, Elvin L., Jr.; Miller, James B.

    1988-01-01

    The design, development, and implementation status of the Surface Control Actuator System (SCAS) for the Hoop/Column Antenna are described with the primary focus on the design of the mechanical element. The SCAS is an electromechanical system that will automatically adjust the antenna shape by changing the length of control cords. Achieving and maintaining the proper surface shape and smoothness are critical to optimizing the electromagnetic characteristics of the antenna.

  18. Effects of enhanced denitrification on hydrodynamics and microbial community structure in a soil column system.

    PubMed

    Calderer, M; Martí, V; de Pablo, J; Guivernau, M; Prenafeta-Boldú, F X; Viñas, M

    2014-09-01

    Enhanced heterotrophic denitrification by adding glucose was investigated by means of a soil column experiment which simulated the groundwater flow. The carbon-to-nitrogen ratio was the main factor determining denitrification potential under experimental conditions. The influence of stimulated denitrification on the autochthonous microbial community was investigated by quantitative PCR (qPCR), and denaturing gradient gel electrophoresis (DGGE). The qPCR detection of the nosZ genes encoding nitrous oxide reductase, and the comparison of the abundances of 16S rRNA genes revealed that the addition of glucose enhanced denitrification leading to an increase in both the total eubacteria and, in particular, in the ratio of denitrifying bacteria, which represented the 21% of the total native eubacteria on the basis of nosZ/16S rRNA gene ratio. Microbial community profiling by DGGE indicated that ribotypes closely related to the genera Acidovorax and Hydrogenophaga (Comamonadaceae family) became enriched in the soil column. The effects of biomass occurrence in the column system on soil hydrodynamics, assessed by tracer studies, revealed a reduction of porosity and a significant increase of dispersivity that could be caused by the appearance of new functional microbial biomass in the aquifer material under enhanced denitrifying conditions. The importance of investigating the microbial growth in relation to the hydrodynamic effects, during enhanced denitrification, has been revealed in the column system experiments associated with the bioremediation. Combining microbial characterisation and hydrodynamic data in a soil column system permits us to gain an insight to the limiting factors of different stimulation strategies that can be applied in the field.

  19. Comprehensive two-dimensional high performance liquid chromatography system with immobilized liposome chromatography column and monolithic column for separation of the traditional Chinese medicine Schisandra chinensis.

    PubMed

    Wang, Shuowen; Wang, Chen; Zhao, Xin; Mao, Shilong; Wu, Yutian; Fan, Guorong

    2012-02-03

    A comprehensive two-dimensional (2D) separation is one that employs two separation dimensions (columns) and draws on all of the available resolving power from each of the dimensions of separate the components in a sample. In this study, a comprehensive 2D chromatography approach was developed for the separation and identification of membrane permeable compounds in a famous traditional Chinese medicine of Schisandra chinensis. The first dimensional column was the immobilized liposome chromatography (ILC) column, which mimics the biological membranes and can be used to study drug-membrane interactions in liquid chromatography. Using an automatic ten-port switching valve equipped with two sample loops, the section of the first-dimension was introduced in the second-dimension consist of a silica monolithic column. More than 40 components in Schisandra chinensis were resolved by using the developed separation system and among them 14 compounds were identified interacting with the ILC column based on their retention action, UV and mass data. With this comprehensive 2D-HPLC system, the three-dimensional chromatographic fingerprints of Schisandra chinensis were preliminarily established and processed by using principal component analysis and hierarchical clustering analysis. The obtained information can distinguish the unacceptable samples of the quality control. The result demonstrated that the 2D biochromatography system has been demonstrated to have more advantages of finding strong binding bioactive components, providing an enhanced peak capacity, good sensitivity and powerful resolution biological fingerprinting analysis of complex TCMs, which was a useful means to control the quality of and to clarify the membrane permeability of the compounds in Schisandra chinensis.

  20. Biodegradation of high concentrations of tetrachloroethene in a continuous flow column system

    SciTech Connect

    Isalou, M; Sleep, B.E.; Liss, S.N.

    1998-11-15

    A long-term (2.5 years) study of the anaerobic biodegradation of high concentrations of perchloroethylene (PCE) was carried out in a continuously operated laboratory column filled with sand which was inoculated with biomass from an anaerobic digester. Concentrations of PCE fed to the column were increased from 12 {micro}M to over 600 {micro}M over 21 months, with methanol added as electron donor. Vinyl chloride (VC) was the terminal product of PCE dechlorination for the first 21 months at which point significant conversion of VC to ethylene (ETH) was detected. The onset of ETH production coincided with acetogenesis becoming the primary pathway for methanol metabolism. ETH production occurred in the column in the presence of PCE and TCE. Varying methanol:PCE molar ratios from 1.4 to 7.5 had little effect on the transformation of PCE and TCE to VC. The degradation of VC to ETH was much more sensitive, and VC accumulated when the methanol:PCE molar ratio dropped below 5.0. Withdrawal of PCE from the system for a 5 month period and maintenance of the column on methanol alone did not result in the loss of PCE degradation capability of the consortium.

  1. Experimental Evaluation of the Failure of a Seismic Design Category - B Precast Concrete Beam-Column Connection System

    DTIC Science & Technology

    2014-12-01

    ER D C TR -1 4 -1 2 Experimental Evaluation of the Failure of a Seismic Design Category – B Precast Concrete Beam-Column Connection...ERDC TR-14-12 December 2014 Experimental Evaluation of the Failure of a Seismic Design Category – B Precast Concrete Beam-Column Connection...experiment to test a precast concrete beam-column system to failure. This experiment was designed to evaluate the performance of precast frame

  2. Nonlinear properties of multiphase high-temperature superconductors of the Bi-Sr-Ca-Cu-O system in the temperature range of the superconducting transition

    NASA Astrophysics Data System (ADS)

    Golev, I. M.; Sergeev, A. V.; Kalyadin, O. V.

    2017-01-01

    The nonlinear characteristics of high-temperature superconductors of the Bi-Sr-Ca-Cu-O system have been experimentally investigated in the temperature range of the superconducting transition under the influence of a harmonic alternating magnetic field. The effect of the generation of odd harmonics in the signal of response to a harmonic alternating magnetic field for multiphase high-temperature superconductors containing regions with different values of the critical temperature in their bulk has been observed for the first time. The mechanism of harmonic generation in a superconductor in the resistive state, which is associated with the switch effect, i.e., with the redistribution of eddy current density between the local regions of the superconductor, has been considered.

  3. GE Healthcare launches multiphase advertising effort.

    PubMed

    2006-01-01

    GE Healthcare has launched a multi-phase marketing campaign aimed at promoting the technological breakthroughs and state-of-the-art equipment that it provides hospitals and health systems to ensure that patients are given the best care possible. The campaign boasts four new commercials and an interactive Web site designed to illustrate healthy living on a global scale.

  4. Biomechanical investigation of two plating systems for medial column fusion in foot

    PubMed Central

    Simons, Paul; Sommerer, Theresia; Zderic, Ivan; Wahl, Dieter; Lenz, Mark; Skulev, Hristo; Knobe, Matthias; Gueorguiev, Boyko; Richards, R. Geoff; Klos, Kajetan

    2017-01-01

    Background Arthrodesis of the medial column (navicular, cuneiform I and metatarsal I) is performed for reasons such as Charcot arthropathy, arthritis, posttraumatic reconstruction or severe pes planus. However, the complication rate is still high and mainly resulting from inadequate fixation. Special plates, designed for medial column arthrodesis, seem to offer potential to reduce the complication rate. The aim of this study was to investigate biomechanically plantar and dorsomedial fusion of the medial column using two new plating systems. Methods Eight matched pairs of human cadaveric lower legs were randomized in two groups and medial column fusion was performed using either plantar or dorsomedial variable-angle locking compression plates. The specimens were biomechanically tested under cyclic progressively increasing axial loading with physiological profile of each cycle. In addition to the machine data, mediolateral x-rays were taken every 250 cycles and motion tracking was performed to determine movements at the arthrodesis site. Statistical analysis of the parameters of interest was performed at a level of significance p = 0.05. Results Displacement of the talo-navicular joint after 1000, 2000 and 4000 cycles was significantly lower for plantar plating (p≤0.039) while there was significantly less movement in the naviculo-cuneiform I joint for dorsal plating post these cycle numbers (p<0.001). Displacements in all three joints of the medial column, as well as angular and torsional deformations between the navicular and metatarsal I increased significantly for each plating technique between 1000, 2000 and 4000 cycles (p≤0.021). The two plating systems did not differ significantly with regard to stiffness and cycles to failure (p≥0.171). Conclusion From biomechanical point of view, although dorsomedial plating showed less movement than plantar plating in the current setup under dynamic loading, there was no significant difference between the two plating

  5. The setup of an extraction system coupled to a hydrogen isotopes distillation column

    SciTech Connect

    Zamfirache, M.; Bornea, A.; Stefanescu, I.; Bidica, N.; Balteanu, O.; Bucur, C.

    2008-07-15

    Among the most difficult problems of cryogenic distillation one stands apart: the extraction of the heavy fraction. By an optimal design of the cycle scheme, this problem could be avoided. A 'worst case scenario' is usually occurring when the extracted fraction consists of one prevalent isotope such as hydrogen and small amounts of the other two hydrogen isotopes (deuterium and/or tritium). This situation is further complicated by two parameters of the distillation column: the extraction flow rate and the hold-up. The present work proposes the conceptual design of an extraction system associated to the cryogenic distillation column used in hydrogen separation processes. During this process, the heavy fraction (DT, T{sub 2}) is separated, its concentration being the highest at the bottom of the distillation column. From this place the extraction of the gaseous phase can now begin. Being filled with adsorbent, the extraction system is used to temporarily store the heavy fraction. Also the extraction system provides samples for the gas Chromatograph. The research work is focused on the existent pilot plant for tritium and deuterium separation from our institute to validate the experiments carried out until now. (authors)

  6. A new fully automated FTIR system for total column measurements of greenhouse gases

    NASA Astrophysics Data System (ADS)

    Geibel, M. C.; Gerbig, C.; Feist, D. G.

    2010-10-01

    This article introduces a new fully automated FTIR system that is part of the Total Carbon Column Observing Network (TCCON). It will provide continuous ground-based measurements of column-averaged volume mixing ratio for CO2, CH4 and several other greenhouse gases in the tropics. Housed in a 20-foot shipping container it was developed as a transportable system that could be deployed almost anywhere in the world. We describe the automation concept which relies on three autonomous subsystems and their interaction. Crucial components like a sturdy and reliable solar tracker dome are described in detail. The automation software employs a new approach relying on multiple processes, database logging and web-based remote control. First results of total column measurements at Jena, Germany show that the instrument works well and can provide parts of the diurnal as well as seasonal cycle for CO2. Instrument line shape measurements with an HCl cell suggest that the instrument stays well-aligned over several months. After a short test campaign for side by side intercomaprison with an existing TCCON instrument in Australia, the system will be transported to its final destination Ascension Island.

  7. Multiphase flow and transport in porous media

    NASA Astrophysics Data System (ADS)

    Parker, J. C.

    1989-08-01

    Multiphase flow and transport of compositionally complex fluids in geologic media is of importance in a number of applied problems which have major social and economic effects. In petroleum reservoir engineering, efficient recovery of energy reserves is the principal goal. Unfortunately, some of these hydrocarbons and other organic chemicals often find their way unwanted into the soils and groundwater supplies. Removal in the latter case is predicated on ensuring the public health and safety. In this paper, principles of modeling fluid flow in systems containing up to three fluid phases (namely, water, air, and organic liquid) are described. Solution of the governing equations for multiphase flow requires knowledge of functional relationships between fluid pressures, saturations, and permeabilities which may be formulated on the basis of conceptual models of fluid-porous media interactions. Mechanisms of transport in multicomponent multiphase systems in which species may partition between phases are also described, and the governing equations are presented for the case in which local phase equilibrium may be assumed. A number of hypothetical numerical problems are presented to illustrate the physical behavior of systems in which multiphase flow and transport arise.

  8. Selecting the column configuration with lowest media replacement cost for small adsorption systems.

    PubMed

    Bausk, Artem S; Dvorak, Bruce I

    2016-04-15

    A framework was developed for preliminary evaluation of the relative media replacement costs of three alternative column configurations used for adsorption systems with two vessels, such as those serving small systems. The media replacement cost is the cost of fresh media and the replacement service cost (including transportation, labor, and other non-material costs). Cost normalization methods were developed in part based on the data from US EPA Arsenic Treatment Technology Demonstration Program. Adsorption equilibrium and kinetics were modeled using the PSDM model and breakthrough curves were normalized using the target effluent to influent concentration ratio (C/Co) and the mass transfer zone fraction (%MTZBT). Two factors were found to be important for the relative replacement cost of each configuration - the frequency which at least one column needed replacement of media, and the cycle replacement cost (CRCost) which is a combination of the fresh media cost and the replacement service cost. The lead-lag configuration has the lowest annual replacement cost at low target C/Co, high %MTZBT, and high CRCost ratios. The parallel configuration performs better at high target C/Co, high %MTZBT, and high CRCost ratios. Although the single configuration (two columns operated in tandem and replaced simultaneously) has higher media consumption compared to lead-lag and parallel, it can result in the lowest replacement cost at short %MTZBT and very low CRCost ratios due to savings in the replacement service cost.

  9. Eruption column physics

    SciTech Connect

    Valentine, G.A.

    1997-03-01

    In this paper the author focuses on the fluid dynamics of large-scale eruption columns. The dynamics of these columns are rooted in multiphase flow phenomena, so a major part of the paper sets up a foundation on that topic that allows one to quickly assess the inherent assumptions made in various theoretical and experimental approaches. The first part is centered on a set of complex differential equations that describe eruption columns, but the focus is on a general understanding of important physical processes rather than on the mathematics. The author discusses briefly the relative merits and weaknesses of different approaches, emphasizing that the largest advances in understanding are made by combining them. He then focuses on dynamics of steady eruption columns and then on transient phenomena. Finally he briefly reviews the effects of varying behavior of the ambient medium through which an eruption column moves. These final sections will emphasize concepts and a qualitative understanding of eruption dynamics. This paper relies on principles of continuum mechanics and transport processes but does not go into detail on the development of those principles. 36 refs., 36 figs., 3 tabs.

  10. Multi column cell (MCC) e-beam exposure system for mask writing

    NASA Astrophysics Data System (ADS)

    Yasuda, Hiroshi; Yamada, Akio; Yamabe, Masaki

    2008-05-01

    Association of Super-Advanced Electronics Technologies (ASET) Mask Design, Drawing, and Inspection Technology Research Department (Mask D2I) started a 4-year development program for the total optimization of mask design, drawing, and inspection technologies to reduce photomask manufacturing costs in 2006. At the Mask Writing Equipment Technology Research Laboratory, we are developing an e-beam exposure system introducing concepts of MCC (multi column cell), CP (character projection), and VSB (variable shaped beam), which has several times higher throughput than currently commercially available e-beam writing systems.

  11. Multiphase, multicomponent parameter estimation for liquid and vapor fluxes in deep arid systems using hydrologic data and natural environmental tracers

    USGS Publications Warehouse

    Kwicklis, E.M.; Wolfsberg, A.V.; Stauffer, P.H.; Walvoord, M.A.; Sully, M.J.

    2006-01-01

    Multiphase, multicomponent numerical models of long-term unsaturated-zone liquid and vapor movement were created for a thick alluvial basin at the Nevada Test Site to predict present-day liquid and vapor fluxes. The numerical models are based on recently developed conceptual models of unsaturated-zone moisture movement in thick alluvium that explain present-day water potential and tracer profiles in terms of major climate and vegetation transitions that have occurred during the past 10 000 yr or more. The numerical models were calibrated using borehole hydrologic and environmental tracer data available from a low-level radioactive waste management site located in a former nuclear weapons testing area. The environmental tracer data used in the model calibration includes tracers that migrate in both the liquid and vapor phases (??D, ??18O) and tracers that migrate solely as dissolved solutes (Cl), thus enabling the estimation of some gas-phase as well as liquid-phase transport parameters. Parameter uncertainties and correlations identified during model calibration were used to generate parameter combinations for a set of Monte Carlo simulations to more fully characterize the uncertainty in liquid and vapor fluxes. The calculated background liquid and vapor fluxes decrease as the estimated time since the transition to the present-day arid climate increases. However, on the whole, the estimated fluxes display relatively little variability because correlations among parameters tend to create parameter sets for which changes in some parameters offset the effects of others in the set. Independent estimates on the timing since the climate transition established from packrat midden data were essential for constraining the model calibration results. The study demonstrates the utility of environmental tracer data in developing numerical models of liquid- and gas-phase moisture movement and the importance of considering parameter correlations when using Monte Carlo analysis to

  12. New electron optical column with large field for nanometer e-beam lithography system

    NASA Astrophysics Data System (ADS)

    Ohta, Hiroya; Matsuzaka, Takashi; Saitou, Norio

    1995-05-01

    An electron beam lithography system for nanometer devices has been developed. The target specifications of the system are a Gaussian beam diameter of 10 nm and a beam current of 1 nA, an acceleration voltage of 50 kV, a 500 micrometers X 500 micrometers deflection field and an overlay accuracy of 10 nm (3(sigma) ). To realize such high performance, the following two technologies have been developed for the design of the electron optical column: (1) a low aberration objective lens system with a one stage electrostatic deflector and (2) a thermal field emission (TFE) gun system with a low energy spread and a high brightness Zr/O/W cathode. The exposed results shown are a 30 nm isolated line and a 40 nm lines and spaces. An overlay accuracy of 10 nm are also obtained. This system is capable of being put into practical use in the fabrication of nanometer devices.

  13. Influence of detergent formulation on nutrient movement through sand columns simulating mound and conventional septic system drainfields

    NASA Astrophysics Data System (ADS)

    Alhajjar, Bashar J.; Linn Gould, C.; Chesters, Gordon; Harkin, John M.

    1990-12-01

    The effects of phosphate (P) and zeolite (Z) -built detergents on leaching of N and P through sand columns simulating septic system drainfields were examined in laboratory columns. To simulate mound septic system drainfields, paired sets of columns were dosed intermittently with septic tank effluent from households using P- or Z-built detergent. Two other paired sets of columns were flooded with P- or Z-effluent to simulate new conventional septic system drainfields; after clogging mats or "crusts" developed at infiltration surface, the subsurfaces of the columns were aerated to simulate mature (crusted) conventional septic system drainfields. NO 3 loading in leachate was 1.1 times higher and ortho-P loading was 4.3 times lower when columns were dosed with Z- than with P-effluent. Dosed columns removed P poorly; total phosphorus (TP) loading in leachate was 81 and 19 g m -2 yr -1 with P- and Z-effluent, respectively. In flooded columns 1.3, 2.0 and 1.8 times more NH 4, organic nitrogen (ON) and total nitrogen (TN) respectively, were leached with Z- than with P-effluent; NO 3 leaching was similar. Flooded columns removed P efficiently; TP leached through flooded systems was 2.5 and 1.4 g m -2 yr -1 with P- and Z effluent, respectively. Crusted columns fed Z-effluent leached 1.2, 2.6, 1.4 and 2.1 times more NH 4, NO 3, ON and TN, respectively, than those with P-effluent but 1.8 times less TP. Crusted columns removed P satisfactorily: 8.2 and 4.6 g m -2 yr -1 TP with P- and Z-effluent, respectively. The P-built detergent substantially improves the efficiency of N removal with satisfactory P removal in columns simulating conventional septic system drainfield. Simultaneous removal of N and P under flooded conditions might be explained by precipitation of struvite-type minerals. Dosed system drainfields were less efficient in removing N and P compared to flooded and crusted system drainfelds.

  14. Multiphase Oscillator Using Traveling Pulses Developed in a System of Transmission Lines with Regularly Spaced Resonant-tunneling Diodes

    NASA Astrophysics Data System (ADS)

    Narahara, Koichi

    2017-02-01

    A scheme is proposed for generating multiphase oscillatory signals in millimeter-wave frequencies based on the dynamics of a traveling pulse developed in a closed transmission line periodically loaded with resonant-tunneling diodes (RTDs) that is coupled with several straight RTD lines. When supplied with an appropriate voltage at the end of an RTD line, a pulse edge is shown to exhibit a spatially extended limit-cycle oscillation on the line. We consider the case where several RTD lines are connected halfway to a closed one at even intervals. In this case, the oscillatory edge developed in each straight RTD line is mutually synchronized such that a pulse-shaped rotary traveling wave develops on the closed RTD line. The oscillating edge on each straight line is also synchronized with the traveling pulse on the closed line, such that the leading edge of the traveling pulse on the closed line and the forward edge on the straight line pass the cross point simultaneously. As a result, when N L straight lines are connected to the closed line, the phase difference between two adjacent oscillatory edges becomes 2π/N L . On the other hand, the trailing edge of the traveling pulse at the cross point breaks the voltage wave on the straight line into two pieces, one of which travels forward to form a solitary wave and the other of which travels backward to reach the input end, where it is reflected and starts to travel forward and this forward moving edge is supposed to be synchronized with the leading edge of the traveling pulse. It means that a back-and-forth edge and a forward-moving solitary wave develop periodically on each straight line. Because the time required for the traveling pulse to go around the closed line must be coincident with the period of the edge oscillation on each straight line, a unique traveling pulse cannot synchronize with each oscillating edge when the cell size of the closed line becomes large, resulting in the development of multiple traveling

  15. Feasibility of aseptic processing of a low-acid multiphase food product (salsa con queso) using a continuous flow microwave system.

    PubMed

    Kumar, P; Coronel, P; Simunovic, J; Sandeep, K P

    2007-04-01

    Aseptic processing of a low-acid multiphase food product using a continuous flow microwave heating system can combine the advantages of an aseptic process along with those of microwave heating. Dielectric properties of 2 different brands of 1 such product (salsa con queso) were measured under continuous flow conditions at a temperature range of 20 to 130 degrees C. At 915 MHz, the dielectric constant ranged from 58.7 at 20 degrees C to 41.3 at 130 degrees C with dielectric loss factor ranging from 41.0 at 20 degrees C to 145.5 at 130 degrees C. The loss tangent at 915 MHz ranged from 0.61 at 20 degrees C to 3.52 at 130 degrees C. The temperature profiles at the outlet during processing of salsa con queso in a 5-kW microwave unit showed a narrow temperature distribution between the center and the wall of the tube. The study showed the feasibility of aseptic processing of salsa con queso using a continuous flow microwave system.

  16. Low energy gamma ray attenuation in multiphase water

    NASA Technical Reports Server (NTRS)

    Singh, Jag J.; Sprinkle, Danny R.; Eftekhari, Abe

    1990-01-01

    A gauging system is proposed to enable monitoring of slush density, solid-liquid interface, and slush level as well as its flow rate. It is based on the principle that the electromagnetic radiation mass attenuation coefficient of a multiphase chemical compound is constant for all relative phase concentrations. Results showing the essential constancy of mass attenuation coefficients for single-phase water vapor, liquid water, ice, and multiphase mixtures of water/ice are described.

  17. Implications of soil mixing for NAPL source zone remediation: Column studies and modeling of field-scale systems.

    PubMed

    Olson, Mitchell R; Sale, Tom C

    2015-01-01

    Soil remediation is often inhibited by subsurface heterogeneity, which constrains contaminant/reagent contact. Use of soil mixing techniques for reagent delivery provides a means to overcome contaminant/reagent contact limitations. Furthermore, soil mixing reduces the permeability of treated soils, thus extending the time for reactions to proceed. This paper describes research conducted to evaluate implications of soil mixing on remediation of non-aqueous phase liquid (NAPL) source zones. The research consisted of column studies and subsequent modeling of field-scale systems. For column studies, clean influent water was flushed through columns containing homogenized soils, granular zero valent iron (ZVI), and trichloroethene (TCE) NAPL. Within the columns, NAPL depletion occurred due to dissolution, followed by either column-effluent discharge or ZVI-mediated degradation. Complete removal of TCE NAPL from the columns occurred in 6-8 pore volumes of flow. However, most of the TCE (>96%) was discharged in the column effluent; less than 4% of TCE was degraded. The low fraction of TCE degraded is attributed to the short hydraulic residence time (<4 days) in the columns. Subsequently, modeling was conducted to scale up column results. By scaling up to field-relevant system sizes (>10 m) and reducing permeability by one-or-more orders of magnitude, the residence time could be greatly extended, potentially for periods of years to decades. Model output indicates that the fraction of TCE degraded can be increased to >99.9%, given typical post-mixing soil permeability values. These results suggest that remediation performance can be greatly enhanced by combining contaminant degradation with an extended residence time.

  18. Implications of soil mixing for NAPL source zone remediation: Column studies and modeling of field-scale systems

    NASA Astrophysics Data System (ADS)

    Olson, Mitchell R.; Sale, Tom C.

    2015-06-01

    Soil remediation is often inhibited by subsurface heterogeneity, which constrains contaminant/reagent contact. Use of soil mixing techniques for reagent delivery provides a means to overcome contaminant/reagent contact limitations. Furthermore, soil mixing reduces the permeability of treated soils, thus extending the time for reactions to proceed. This paper describes research conducted to evaluate implications of soil mixing on remediation of non-aqueous phase liquid (NAPL) source zones. The research consisted of column studies and subsequent modeling of field-scale systems. For column studies, clean influent water was flushed through columns containing homogenized soils, granular zero valent iron (ZVI), and trichloroethene (TCE) NAPL. Within the columns, NAPL depletion occurred due to dissolution, followed by either column-effluent discharge or ZVI-mediated degradation. Complete removal of TCE NAPL from the columns occurred in 6-8 pore volumes of flow. However, most of the TCE (> 96%) was discharged in the column effluent; less than 4% of TCE was degraded. The low fraction of TCE degraded is attributed to the short hydraulic residence time (< 4 days) in the columns. Subsequently, modeling was conducted to scale up column results. By scaling up to field-relevant system sizes (> 10 m) and reducing permeability by one-or-more orders of magnitude, the residence time could be greatly extended, potentially for periods of years to decades. Model output indicates that the fraction of TCE degraded can be increased to > 99.9%, given typical post-mixing soil permeability values. These results suggest that remediation performance can be greatly enhanced by combining contaminant degradation with an extended residence time.

  19. Chemometric evaluation of the column classification system during the pharmaceutical analysis of lamotrigine and its related substances.

    PubMed

    Szulfer, Jarosław; Plenis, Alina; Bączek, Tomasz

    2013-08-01

    This paper investigates the performance of a column classification system developed at the Katholieke Universiteit Leuven applied to pharmaceutical chromatographic analyses. The liquid chromatography assay of lamotrigine and related compounds was carried out according to the method prescribed in the European Pharmacopoeia monograph, using 28 brands of stationary phases. A ranking was built based on the F KUL value calculated against the selected reference column, then compared with the column test performance established for the stationary phases studied. Therefore, the system suitability test prescribed by the European Pharmacopoeia in order to distinguish between suitable or unsuitable columns for this analysis was evaluated. Moreover, it was examined whether the classes of the stationary phases, determined using test parameter results, contain either suitable or unsuitable supports for the lamotrigine separation. This assay was performed using chemometric a technique, namely factor analysis.

  20. NMR studies of multiphase flows II

    SciTech Connect

    Altobelli, S.A.; Caprihan, A.; Fukushima, E.

    1995-12-31

    NMR techniques for measurements of spatial distribution of material phase, velocity and velocity fluctuation are being developed and refined. Versions of these techniques which provide time average liquid fraction and fluid phase velocity have been applied to several concentrated suspension systems which will not be discussed extensively here. Technical developments required to further extend the use of NMR to the multi-phase flow arena and to provide measurements of previously unobtainable parameters are the focus of this report.

  1. Estimation of mechanical dispersion and dispersivity in a soil-gas system by column experiments and the dusty gas model.

    PubMed

    Hibi, Yoshihiko; Kanou, Yuki; Ohira, Yuki

    2012-04-01

    In a previous study, column experiments were carried out with Toyoura sand (permeability 2.05×10(-11)m(2)) and Toyoura sand mixed with bentonite (permeability 9.96×10(-13)m(2)) to obtain the molecular diffusion coefficient, the Knudsen diffusion coefficient, the tortuosity for the molecular diffusion coefficient, and the mechanical dispersion coefficient of soil-gas systems. In this study, we conducted column experiments with field soil (permeability 2.0×10(-13)m(2)) and showed that the above parameters can be obtained for both less-permeable and more-permeable soils by using the proposed method for obtaining the parameters and performing column experiments. We then estimated dispersivity from the mechanical dispersion coefficients obtained by the column experiments. We found that the dispersivity depended on the mole fraction of the tracer gas and could be represented by a quadratic equation.

  2. Multiphase booster ups production from subsea well

    SciTech Connect

    1995-05-01

    The Rogn South subsea well has the world`s first commercial subsea multiphase boosting system. The well produces to A/S Norske Shell`s Draugen field, in the Norwegian Sea. The Smubs (Shell multiphase underwater booster station) provides additional energy to transport a mixture of gas and liquids over long distances. This reduces the back pressure on the reservoir to potentially enhance both production and recovery. In-house Shell International Petroleum Maatschappij B.V. (SIPM) has studied estimated facility costs and performance for a multiphase boosting system for a typical small (50 million bbl) field between 20--50 km from a host facility in water depths between 150--1,000 m. The studies showed that technical costs per barrel of oil produced could be cut by up to 30% compared to conventional technology. The Smubs main features are: A single retrievable cartridge that houses all active components susceptible to wear; No orientation requirements for the pump cartridge unit; No orientation requirements for the pump cartridge unit; Hydraulically set and tested seals; and Vertical installation and retrieval with a single tool, and a remotely operated vehicle (ROV) only for a monitoring.

  3. Competing Uses of Underground Systems Related to Energy Supply: Applying Single- and Multiphase Simulations for Site Characterization and Risk-Analysis

    NASA Astrophysics Data System (ADS)

    Kissinger, A.; Walter, L.; Darcis, M.; Flemisch, B.; Class, H.

    2012-04-01

    Global climate change, shortage of resources and the resulting turn towards renewable sources of energy lead to a growing demand for the utilization of subsurface systems. Among these competing uses are Carbon Capture and Storage (CCS), geothermal energy, nuclear waste disposal, "renewable" methane or hydrogen storage as well as the ongoing production of fossil resources like oil, gas, and coal. Besides competing among themselves, these technologies may also create conflicts with essential public interests like water supply. For example, the injection of CO2 into the underground causes an increase in pressure reaching far beyond the actual radius of influence of the CO2 plume, potentially leading to large amounts of displaced salt water. Finding suitable sites is a demanding task for several reasons. Natural systems as opposed to technical systems are always characterized by heterogeneity. Therefore, parameter uncertainty impedes reliable predictions towards capacity and safety of a site. State of the art numerical simulations combined with stochastic approaches need to be used to obtain a more reliable assessment of the involved risks and the radii of influence of the different processes. These simulations may include the modeling of single- and multiphase non-isothermal flow, geo-chemical and geo-mechanical processes in order to describe all relevant physical processes adequately. Stochastic approaches have the aim to estimate a bandwidth of the key output parameters based on uncertain input parameters. Risks for these different underground uses can then be made comparable with each other. Along with the importance and the urgency of the competing processes this may lead to a more profound basis for a decision. Communicating risks to stake holders and a concerned public is crucial for the success of finding a suitable site for CCS (or other subsurface utilization). We present and discuss first steps towards an approach for addressing the issue of competitive

  4. Laboratory analogue of a supersonic accretion column in a binary star system

    NASA Astrophysics Data System (ADS)

    Cross, J. E.; Gregori, G.; Foster, J. M.; Graham, P.; Bonnet-Bidaud, J.-M.; Busschaert, C.; Charpentier, N.; Danson, C. N.; Doyle, H. W.; Drake, R. P.; Fyrth, J.; Gumbrell, E. T.; Koenig, M.; Krauland, C.; Kuranz, C. C.; Loupias, B.; Michaut, C.; Mouchet, M.; Patankar, S.; Skidmore, J.; Spindloe, C.; Tubman, E. R.; Woolsey, N.; Yurchak, R.; Falize, É.

    2016-06-01

    Astrophysical flows exhibit rich behaviour resulting from the interplay of different forms of energy--gravitational, thermal, magnetic and radiative. For magnetic cataclysmic variable stars, material from a late, main sequence star is pulled onto a highly magnetized (B>10 MG) white dwarf. The magnetic field is sufficiently large to direct the flow as an accretion column onto the poles of the white dwarf, a star subclass known as AM Herculis. A stationary radiative shock is expected to form 100-1,000 km above the surface of the white dwarf, far too small to be resolved with current telescopes. Here we report the results of a laboratory experiment showing the evolution of a reverse shock when both ionization and radiative losses are important. We find that the stand-off position of the shock agrees with radiation hydrodynamic simulations and is consistent, when scaled to AM Herculis star systems, with theoretical predictions.

  5. Laboratory analogue of a supersonic accretion column in a binary star system.

    PubMed

    Cross, J E; Gregori, G; Foster, J M; Graham, P; Bonnet-Bidaud, J-M; Busschaert, C; Charpentier, N; Danson, C N; Doyle, H W; Drake, R P; Fyrth, J; Gumbrell, E T; Koenig, M; Krauland, C; Kuranz, C C; Loupias, B; Michaut, C; Mouchet, M; Patankar, S; Skidmore, J; Spindloe, C; Tubman, E R; Woolsey, N; Yurchak, R; Falize, É

    2016-06-13

    Astrophysical flows exhibit rich behaviour resulting from the interplay of different forms of energy-gravitational, thermal, magnetic and radiative. For magnetic cataclysmic variable stars, material from a late, main sequence star is pulled onto a highly magnetized (B>10 MG) white dwarf. The magnetic field is sufficiently large to direct the flow as an accretion column onto the poles of the white dwarf, a star subclass known as AM Herculis. A stationary radiative shock is expected to form 100-1,000 km above the surface of the white dwarf, far too small to be resolved with current telescopes. Here we report the results of a laboratory experiment showing the evolution of a reverse shock when both ionization and radiative losses are important. We find that the stand-off position of the shock agrees with radiation hydrodynamic simulations and is consistent, when scaled to AM Herculis star systems, with theoretical predictions.

  6. Laboratory analogue of a supersonic accretion column in a binary star system

    PubMed Central

    Cross, J. E.; Gregori, G.; Foster, J. M.; Graham, P.; Bonnet-Bidaud, J. -M.; Busschaert, C.; Charpentier, N.; Danson, C. N.; Doyle, H. W.; Drake, R. P.; Fyrth, J.; Gumbrell, E. T.; Koenig, M.; Krauland, C.; Kuranz, C. C.; Loupias, B.; Michaut, C.; Mouchet, M.; Patankar, S.; Skidmore, J.; Spindloe, C.; Tubman, E. R.; Woolsey, N.; Yurchak, R.

    2016-01-01

    Astrophysical flows exhibit rich behaviour resulting from the interplay of different forms of energy—gravitational, thermal, magnetic and radiative. For magnetic cataclysmic variable stars, material from a late, main sequence star is pulled onto a highly magnetized (B>10 MG) white dwarf. The magnetic field is sufficiently large to direct the flow as an accretion column onto the poles of the white dwarf, a star subclass known as AM Herculis. A stationary radiative shock is expected to form 100–1,000 km above the surface of the white dwarf, far too small to be resolved with current telescopes. Here we report the results of a laboratory experiment showing the evolution of a reverse shock when both ionization and radiative losses are important. We find that the stand-off position of the shock agrees with radiation hydrodynamic simulations and is consistent, when scaled to AM Herculis star systems, with theoretical predictions. PMID:27291065

  7. Prevention of co-elution of steroid sulfates with serum proteins from pre-column in column-switching HPLC system.

    PubMed

    Tagawa, N; Tsuruta, H; Fujinami, A; Kobayashi, Y

    1998-11-01

    A method to prevent co-elution of steroid sulfates with proteins in serum from the pre-column in column-switching HPLC was developed. The pre-column, a polymer-coated mixed function column, was used for ion-pair chromatography with 5 mM tetra-n-butylammonium (TBA) ion. As steroid sulfates, estriol 3-sulfate, dehydroepiandrosterone 3-sulfate and pregnenolone 3-sulfate were used. Human serum (25 microl) was diluted with mobile phases including 5, 100 and 500 mM TBA ion, and then injected directly into the pre-column. The peak areas of the steroid sulfates in serum samples were compared with those of the steroid standards without serum. When 25/microl of serum was diluted with mobile phase including 100 or 500 mM TBA ion, the steroid sulfates in serum were retained in the pre-column; however, the steroid sulfates from the same sample diluted with mobile phase containing 5 mM TBA ion were not retained in the pre-column. Addition of an excess amount of counter ion (TBA ion) into the serum sample made it possible to retain the steroid sulfates in the pre-column. This method was applied to column-switching HPLC for measurement of steroid sulfates in serum using a semi-microcolumn as the analytical column.

  8. FOREWORD: International Symposium of Cavitation and Multiphase Flow (ISCM 2014)

    NASA Astrophysics Data System (ADS)

    Wu, Yulin

    2015-01-01

    The International Symposium on Cavitation and Multiphase Flow (ISCM 2014) was held in Beijing, China during 18th-21st October, 2014, which was jointly organized by Tsinghua University, Beijing, China and Jiangsu University, Zhenjiang, China. The co-organizer was the State Key Laboratory of Hydroscience and Engineering, Beijing, China. Cavitation and multiphase flow is one of paramount topics of fluid mechanics with many engineering applications covering a broad range of topics, e.g. hydraulic machinery, biomedical engineering, chemical and process industry. In order to improve the performances of engineering facilities (e.g. hydraulic turbines) and to accelerate the development of techniques for medical treatment of serious diseases (e.g. tumors), it is essential to improve our understanding of cavitation and Multiphase Flow. For example, the present development towards the advanced hydrodynamic systems (e.g. space engine, propeller, hydraulic machinery system) often requires that the systems run under cavitating conditions and the risk of cavitation erosion needs to be controlled. The purpose of the ISCM 2014 was to discuss the state-of-the-art cavitation and multiphase flow research and their up-to-date applications, and to foster discussion and exchange of knowledge, and to provide an opportunity for the researchers, engineers and graduate students to report their latest outputs in these fields. Furthermore, the participants were also encouraged to present their work in progress with short lead time and discuss the encountered problems. ISCM 2014 covers all aspects of cavitation and Multiphase Flow, e.g. both fundamental and applied research with a focus on physical insights, numerical modelling and applications in engineering. Some specific topics are: Cavitating and Multiphase Flow in hydroturbines, pumps, propellers etc. Numerical simulation techniques Cavitation and multiphase flow erosion and anti-erosion techniques Measurement techniques for cavitation and

  9. High Level Waste System Impacts from Small Column Ion Exchange Implementation

    SciTech Connect

    McCabe, D. J.; Hamm, L. L.; Aleman, S. E.; Peeler, D. K.; Herman, C. C.; Edwards, T. B.

    2005-08-18

    The objective of this task is to identify potential waste streams that could be treated with the Small Column Ion Exchange (SCIX) and perform an initial assessment of the impact of doing so on the High-Level Waste (HLW) system. Design of the SCIX system has been performed as a backup technology for decontamination of High-Level Waste (HLW) at the Savannah River Site (SRS). The SCIX consists of three modules which can be placed in risers inside underground HLW storage tanks. The pump and filter module and the ion exchange module are used to filter and decontaminate the aqueous tank wastes for disposition in Saltstone. The ion exchange module contains Crystalline Silicotitanate (CST in its engineered granular form is referred to as IONSIV{reg_sign} IE-911), and is selective for removal of cesium ions. After the IE-911 is loaded with Cs-137, it is removed and the column is refilled with a fresh batch. The grinder module is used to size-reduce the cesium-loaded IE-911 to make it compatible with the sludge vitrification system in the Defense Waste Processing Facility (DWPF). If installed at the SRS, this SCIX would need to operate within the current constraints of the larger HLW storage, retrieval, treatment, and disposal system. Although the equipment has been physically designed to comply with system requirements, there is also a need to identify which waste streams could be treated, how it could be implemented in the tank farms, and when this system could be incorporated into the HLW flowsheet and planning. This document summarizes a preliminary examination of the tentative HLW retrieval plans, facility schedules, decontamination factor targets, and vitrified waste form compatibility, with recommendations for a more detailed study later. The examination was based upon four batches of salt solution from the currently planned disposition pathway to treatment in the SCIX. Because of differences in capabilities between the SRS baseline and SCIX, these four batches were

  10. Analogy between mission critical detection in distributed systems and 13C isotope separation column

    NASA Astrophysics Data System (ADS)

    Boca, Maria L.; Secara, Mihai

    2015-02-01

    Carbon represents the fourth most abundant chemical element in the world, having two stable and one radioactive isotope. The 13 Carbon isotopes, with a natural abundance of 1.1%, plays an important role in numerous applications, such as the study of human metabolism changes, molecular structure studies, non-invasive respiratory tests, Alzheimer tests, air pollution and global warming effects on plants [2]. Distributed systems are increasingly being applied in critical real-time applications and their complexity forces programmers to use design methods which guarantee correctness and increase the maintainability of the products. Objectoriented methodologies are widely used to cope with complexity in any kind of system, but most of them lack a formal foundation to allow the analysis and verification of designs, which is one of the main requirements for dealing with concurrent and reactive systems. This research is intended to make an analogy between two tips of industrial processes, one 13C Isotope Separation Column and other one distributed systems. We try to highlight detection of "mission critical "situations for this two processes and show with one is more critical and needs deeply supervisyon [1], [3].

  11. Optimizing multiphase aquifer remediation using ITOUGH2

    SciTech Connect

    Finsterle, S.; Pruess, K.

    1994-06-01

    The T2VOC computer model for simulating the transport of organic chemical contaminants in non-isothermal multiphase systems has been coupled to the ITOUGH2 code which solves parameter optimization problems. This allows one to use nonlinear programming and simulated annealing techniques to solve groundwater management problems, i.e. the optimization of multiphase aquifer remediation. This report contains three illustrative examples to demonstrate the optimization of remediation operations by means of simulation-minimization techniques. The code iteratively determines an optimal remediation strategy (e.g. pumping schedule) which minimizes, for instance, pumping and energy costs, the time for cleanup, and residual contamination. While minimizing the objective function is straightforward, the relative weighting of different performance measures--e.g. pumping costs versus cleanup time versus residual contaminant content--is subject to a management decision process. The intended audience of this report is someone who is familiar with numerical modeling of multiphase flow of contaminants, and who might actually use T2VOC in conjunction with ITOUGH2 to optimize the design of aquifer remediation operations.

  12. TRAINING TYPISTS IN THE INDUSTRIAL ENVIRONMENT--PRELIMINARY REPORT OF A PROTOTYPE SYSTEM OF SIMULTANEOUS, MULTILEVEL, MULTIPHASIC AUDIO PROGRAMMING.

    ERIC Educational Resources Information Center

    ADAMS, CHARLES F.

    IN 1965 TEN NEGRO AND PUERTO RICAN GIRLS BEGAN CLERICAL TRAINING IN THE NATIONAL ASSOCIATION OF MANUFACTURERS (NAM) TYPING LABORATORY I (TEELAB-I), A PILOT PROJECT TO DEVELOP A SYSTEM OF TRAINING TYPISTS WITHIN THE INDUSTRIAL ENVIRONMENT. THE INITIAL SYSTEM, AN ADAPTATION OF GREGG AUDIO MATERIALS TO A MACHINE TECHNOLOGY, TAUGHT ACCURACY, SPEED…

  13. The Application of Monochromatic Energies to Investigate Multiphase Porous Media Systems using Synchrotron X-ray Tomography

    SciTech Connect

    Ham, Kyungmin; Willson, Clinton S.

    2006-01-31

    X-ray computed tomography (CT) is becoming a useful tool for nondestructive imaging of many geoenvironmental and geotechnical systems. Conventional X-ray CT systems typically utilize a polychromatic X-ray beam. While providing a high throughput of photons, the use of polychromatic energy can make quantifying material concentrations, densities or composition very difficult or impossible without appropriate standards. Synchrotron X-rays have an extremely small angular divergence, thus permitting spatial resolution that is only limited by the optical components of the system. In addition, the ability to tune to a monochromatic X-ray energy allows better phase contrast by reducing beam hardening and allowing for elemental discrimination. In this work we will show how monochromatic energy can be used to provide high-quality images allowing for phase separation several different porous media systems thus improving our ability to quantify a range of processes and phenomena.

  14. Development of a computer simulation technique for predicting heat transfer in multiphase liquid-particle flow systems

    SciTech Connect

    Malone, Kevin F.; Xu, Bao H.; Fairweather, Michael

    2007-07-01

    Many of the highly active waste liquors that result from the reprocessing of spent nuclear fuel contain particulate solids of various materials. Operations for safe processing, handling and intermediate storage of these wastes often pose significant technical challenges due to the need for effective cooling systems to remove the heat generated by the radioactive solids. The multi-scale complexity of liquid-particle flow systems is such that investigation and prediction of their heat transfer characteristics based on experimental studies is a difficult task. Fortunately, the increasing availability of cheap computing power means that predictive simulation tools may be able to provide a means to investigate these systems without the need for expensive pilot studies. In this work we describe the development of a Combined Continuum and Discrete Model (CCDM) for predicting the heat transfer behaviour of systems of particles suspended in liquids. (authors)

  15. Methods, systems and apparatus for optimization of third harmonic current injection in a multi-phase machine

    DOEpatents

    Gallegos-Lopez, Gabriel

    2012-10-02

    Methods, system and apparatus are provided for increasing voltage utilization in a five-phase vector controlled machine drive system that employs third harmonic current injection to increase torque and power output by a five-phase machine. To do so, a fundamental current angle of a fundamental current vector is optimized for each particular torque-speed of operating point of the five-phase machine.

  16. Finite-Element Analysis of Multiphase Immiscible Flow Through Soils

    NASA Astrophysics Data System (ADS)

    Kuppusamy, T.; Sheng, J.; Parker, J. C.; Lenhard, R. J.

    1987-04-01

    A finite-element model is developed for multiphase flow through soil involving three immiscible fluids: namely, air, water, and a nonaqueous phase liquid (NAPL). A variational method is employed for the finite-element formulation corresponding to the coupled differential equations governing flow in a three-fluid phase porous medium system with constant air phase pressure. Constitutive relationships for fluid conductivities and saturations as functions of fluid pressures, which are derived in a companion paper by J. C. Parker et al. (this issue) and which may be calibrated from two-phase laboratory measurements, are employed in the finite-element program. The solution procedure uses backward time integration with iteration by a modified Picard method to handle the nonlinear properties. Laboratory experiments involving water displacement from soil columns by p cymene (a benzene-derivative hydrocarbon) under constant pressure were simulated by the finite-element program to validate the numerical model and formulation for constitutive properties. Transient water outflow predicted using independently measured saturation-capillary head data agreed with observed outflow data within the limits of precision of the predictions as estimated by a first-order Taylor series approximation considering parameter uncertainty due to experimental reproducability and constitutive model accuracy. Two-dimensional simulations are presented for a hypothetical field case involving introduction of NAPL near the soil surface due to leakage from an underground storage tank. Subsequent transport of NAPL in the variably saturated vadose and groundwater zones is analyzed.

  17. Multiphase, multicomponent numerical model of bioventing with nonequilibrium mass exchange

    SciTech Connect

    Lang, J.R.; Rathfelder, K.M.; Abriola, L.M.

    1995-12-31

    A numerical model is presented that has been specifically designed to simulate the combined processes of soil vapor extraction and enhanced bioremediation known as bioventing. In this model, equations describing multiphase flow, multicomponent advective diffusive transport, and biodegradation are coupled. An entrapped organic residual, mobile gas and aqueous phases, and a reactive biophase are modeled. Components include n organic contaminants, oxygen, nitrogen, and water. Rate-limited mass exchange between the phases is simulated using linear driving force expressions. These expressions model volatilization and dissolution of the entrapped organic residual, rate-limited transport between the gas and aqueous phases, and rate-limited transport to the biophase. Monod-type kinetic expressions are employed to describe biophase utilization of substrates, the electron acceptor, and a limiting nutrient, as well as the growth of the microbial population. The coupled nonlinear governing equations are solved using a set iterative finite element method. Numerical simulations are presented for one-dimensional bench-scale column studies. These simulations illustrate the potential importance of biological degradation in the remediation of systems that are subject to mass transfer limitations.

  18. Aspects regarding at 13C isotope separation column control using Petri nets system

    NASA Astrophysics Data System (ADS)

    Boca, M. L.; Ciortea, M. E.

    2015-11-01

    This paper is intended to show that Petri nets can be also applicable in the chemical industry. It used linear programming, modeling underlying Petri nets, especially discrete event systems for isotopic separation, the purpose of considering and control events in real-time through graphical representations. In this paper it is simulate the control of 13C Isotope Separation column using Petri nets. The major problem with 13C comes from the difficulty of obtaining it and raising its natural fraction. Carbon isotopes can be obtained using many methods, one of them being the cryogenic distillation of carbon monoxide. Some few aspects regarding operating conditions and the construction of such cryogenic plants are known today, and even less information are available as far as the separation process modeling and control are concerned. In fact, the efficient control of the carbon monoxide distillation process represents a necessity for large-scale 13C production. Referring to a classic distillation process, some models for carbon isotope separation have been proposed, some based on mass, component and energy balance equations, some on the nonlinear wave theory or the Cohen equations. For modeling the system it was used Petri nets because in this case it is deal with discrete event systems. In use of the non-timed and with auxiliary times Petri model, the transport stream was divided into sections and these sections will be analyzed successively. Because of the complexity of the system and the large amount of calculations required it was not possible to analyze the system as a unitary whole. A first attempt to model the system as a unitary whole led to the blocking of the model during simulation, because of the large processing times.

  19. Improved Design Tools for Surface Water and Standing Column Well Heat Pump Systems (DE-EE0002961)

    SciTech Connect

    Spitler, J. D.; Culling, J. R.; Conjeevaram, K.; Ramesh, M.; Selvakumar, M.

    2012-11-30

    Ground-source heat pump (GSHP) systems are perhaps the most widely used “sustainable” heating and cooling systems, with an estimated 1.7 million installed units with total installed heating capacity on the order of 18 GW. They are widely used in residential, commercial, and institutional buildings. Standing column wells (SCW) are one form of ground heat exchanger that, under the right geological conditions, can provide excellent energy efficiency at a relatively low capital cost. Closed-loop surface water heat pump (SWHP) systems utilize surface water heat exchangers (SWHE) to reject or extract heat from nearby surface water bodies. For building near surface water bodies, these systems also offer a high degree of energy efficiency at a low capital cost. However, there have been few design tools available for properly sizing standing column wells or surface water heat exchangers. Nor have tools for analyzing the energy consumption and supporting economics-based design decisions been available. The main contributions of this project lie in providing new tools that support design and energy analysis. These include a design tool for sizing surface water heat exchangers, a design tool for sizing standing column wells, a new model of surface water heat pump systems implemented in EnergyPlus and a new model of standing column wells implemented in EnergyPlus. These tools will better help engineers design these systems and determine the economic and technical feasibility.

  20. Novel determination system for urea in alcoholic beverages by using an FIA system with an acid urease column.

    PubMed

    Iida, Yasuhiro; Suganuma, Yuko; Matsumoto, Kunio; Satoh, Ikuo

    2006-01-01

    A novel determination method for urea using an acid urease column-FIA system was developed, and the system was applied to the determination of urea in rice wine. This novel FIA system was characterized by CO2 detection due to the property of acid urease and by a microfluidic gas-diffusion device with the use of an ultra-thin hollow fiber membrane. A biosensing system fabricated in this study was assembled with a double-plunger pump, a sample-injection valve, an immobilized acid urease column as a recognition element for the assay of urea, a gas-diffusion unit, and a flow-type spectrophotometer. The gas-diffusion unit consisted of a double-tubing structure in which the outer tubing was made of PTFE (i.d. 1.0 mm; o.d. 1.5 mm) and the inner tubing was of porous PTFE (i.d. 0.19 mm; o.d. 0.25 mm). Standard urea solutions (20 microl) were measured through monitoring variations in the absorbance of a coloring agent solution resulting from a pH shift due to carbon dioxide molecules being enzymatically generated. A wide and linear relationship was obtained between the concentration of urea (16 microM - 1.0 mM) and the change in absorbance. This FIA system has great advantages that the system did not suffer from ammonia and ethanol in samples. This system, armed with a microfluidic gas-diffusion device, was applicable to the determination of various substrates of many kinds of decarboxylase, amino-acid oxidase, and amino-acid oxygenase, producing CO2 and NH3 molecules.

  1. Integrated Systems with Applications to the Multi-Phases of the Ephemerides, Physics and Methematics of the Upper Atmosphere.

    DTIC Science & Technology

    1987-02-27

    opportunity using a low light level TV (LLLTV) co-aligned with the sensor telescope , and a joystick controller in the orbiter aft flight deck. 149 This...capability by the camera simulation portion of the AITS software. 6.4.3 Planned Mission and Updated Kepler Elements The AITS system requires availability of...LOKANGI ’: L MNTOPV and PVTOMN are employed in this vel¢ct-. transformation process. They provide the mw reversibly converting between mean Kepler ri

  2. Experimental Insights into Multiphase (H2O-CO2) Fluid-Rock Interactions in Geothermal Systems

    NASA Astrophysics Data System (ADS)

    Kaszuba, J. P.; Lo Re, C.; Martin, J.; McPherson, B. J.; Moore, J. N.

    2012-12-01

    Integrated hydrothermal experiments and geochemical modeling elucidate fluid-rock interactions and reaction pathways in both natural and anthropogenic systems, including enhanced geothermal systems (EGS) in which CO2 is introduced as a working fluid. Experiments are conducted in rocker bombs and flexible Au-Ti reaction cells. Individual experiments require one to three months to complete; intensive in-situ fluid/gas sampling gauges reaction progress. Investigation of granitic reservoirs and associated vein minerals are broadly based on the Roosevelt Hot Springs thermal area, Utah, USA. The granite consists of subequal amounts of quartz, perthitic K-feldspar (~25% wt% albite and 75% wt% K-feldspar), and oligoclase (An23), and 4 wt% Fe-rich biotite. Vein minerals include epidote and chlorite (clinochlore). Experiments are conducted at 250°C and 25 to 45 MPa. Each experiment uses mineral powders (75 wt% of rock mass, ground to <45 um) to increase reactivity and also mineral pieces (0.1-0.7 cm in size) to promote petrologic evaluation of mineral reactions. The water (I ≈ 0.1 molal) initially contains millimolal quantities of SiO2, Al, Ca, Mg, K, SO4, and HCO3 and is designed to be saturated with all of the minerals present at the start of each experiment. Excess CO2 is injected to saturate the water and maintain an immiscible supercritical fluid phase. The entire evolutionary path of the natural system is not replicated at laboratory scales. Instead, experiments define a segment of the reaction path and, in combination with geochemical modeling, provide clear trajectories towards equilibrium. Reaction of granite+water yields illite+zeolite; smectite subsequently precipitates in response to CO2 injection. Reaction of granite+epidote+water yields illite+zeolite+smectite; zeolite does not precipitate after CO2 is injected. Water in all experiments become saturated with chalcedony. Carbonate minerals do not precipitate but are predicted as final equilbrium products

  3. A Grain-Scale Coupled Model of Multiphase Fluid Flow and Sediment Mechanics: Application to Methane Hydrates in Natural Systems

    NASA Astrophysics Data System (ADS)

    Juanes, R.; Jain, A. K.

    2008-12-01

    We present a discrete element model for the simulation, at the grain scale, of gas migration in brine- saturated deformable media. We account rigorously for the presence of two fluids in the pore space by incorporating grain forces due to pore fluid pressures, and surface tension between fluids. The coupled model permits investigating an essential process that takes place at the base of the hydrate stability zone: the upward migration of methane in its own free gas phase. We elucidate the way in which gas migration may take place: (1) by capillary invasion in a rigid-like medium; and (2) by initiation and propagation of a fracture. We find that the main factor controlling the mode of gas transport in the sediment is the grain size, and show that coarse-grain sediments favor capillary invasion, whereas fracturing dominates in fine-grain media. The results have important implications for understanding hydrates in natural systems. Our results predict that, in fine sediments, hydrate will likely form in veins that follow a fracture-network pattern, and the hydrate concentration in this type of accumulations will likely be quite low. In coarse sediments, the buoyant methane gas is likely to invade the pore space more uniformly, in a process akin to invasion percolation, and the overall pore occupancy is likely to be much higher than for a fracture-dominated regime. These implications are consistent with field observations of methane hydrates in natural systems.

  4. Development of High Precision Metal Micro-Electro-Mechanical-Systems Column for Portable Surface Acoustic Wave Gas Chromatograph

    NASA Astrophysics Data System (ADS)

    Iwaya, Takamitsu; Akao, Shingo; Sakamoto, Toshihiro; Tsuji, Toshihiro; Nakaso, Noritaka; Yamanaka, Kazushi

    2012-07-01

    In the field of environmental measurement and security, a portable gas chromatograph (GC) is required for the on-site analysis of multiple hazardous gases. Although the gas separation column has been downsized using micro-electro-mechanical-systems (MEMS) technology, an MEMS column made of silicon and glass still does not have sufficient robustness and a sufficiently low fabrication cost for a portable GC. In this study, we fabricated a robust and inexpensive high-precision metal MEMS column by combining diffusion-bonded etched stainless-steel plates with alignment evaluation using acoustic microscopy. The separation performance was evaluated using a desktop GC with a flame ionization detector and we achieved the high separation performance comparable to the best silicon MEMS column fabricated using a dynamic coating method. As an application, we fabricated a palm-size surface acoustic wave (SAW) GC combining this column with a ball SAW sensor and succeeded in separating and detecting a mixture of volatile organic compounds.

  5. Development of a multicomponent film diffusion controlled mixed bed ion exchange column model applicable to variable influent systems

    NASA Astrophysics Data System (ADS)

    Hussey, Dennis Frank

    2000-10-01

    Scope and method of study. The purpose of this study was to develop a generalized rate model to handle multicomponent mixed-bed ion exchange (MBIE) with multivalent dissociative species and variable influent conditions. To achieve this goal, mass transfer mechanisms of weak electrolytes in ion exchange column have been studied; and based on which, rate expressions for weak electrolyte transfer have been proposed. In addition, the column material balance has been derived in terms of the constituent species concentrations only. Finally, generalized dissociation equilibrium equations for several types of weak electrolyte constituents were implemented, and the effluent concentrations were determined by solving column material balance equations along with the rate expressions. Findings and conclusions. The mixed bed ion exchange column model has been successfully programmed into a computer program and is capable of predicting the effluent concentration histories, dynamic resin loading, solution, and rate profiles. The column material balance has been satisfied to within 1% for all chemistries studied. The model is capable of simulating variable influent contaminant concentrations and flow rates by sequentially using the loading profiles of previous simulations. The model maintains electroneutrality at all times. Dissociative species transfer is adequate for many systems, but additional work is required to incorporate molecular constituent mass transfer.

  6. Development of the Maypole (Hoop/Column) deployable reflector concept for large space systems applications

    NASA Technical Reports Server (NTRS)

    Montgomery, D. C.; Sikes, L. D.

    1980-01-01

    The conceptual design, performance projections, and materials development for the maypole (hoop/column) reflector concept are summarized. Factors influencing configuration choices are discussed along with quad aperture/feed characteristics and antenna requirements based on missions.

  7. Dissolved nutrients and atrazine removal by column-scale monophasic and biphasic rain garden model systems.

    PubMed

    Yang, Hanbae; McCoy, Edward L; Grewal, Parwinder S; Dick, Warren A

    2010-08-01

    Rain gardens are bioretention systems that have the potential to reduce peak runoff flow and improve water quality in a natural and aesthetically pleasing manner. We compared hydraulic performance and removal efficiencies of nutrients and atrazine in a monophasic rain garden design versus a biphasic design at a column-scale using simulated runoff. The biphasic rain garden was designed to increase retention time and removal efficiency of runoff pollutants by creating a sequence of water saturated to unsaturated conditions. We also evaluated the effect of C substrate availability on pollutant removal efficiency in the biphasic rain garden. Five simulated runoff events with various concentrations of runoff pollutants (i.e. nitrate, phosphate, and atrazine) were applied to the monophasic and biphasic rain gardens once every 5d. Hydraulic performance was consistent over the five simulated runoff events. Peak flow was reduced by approximately 56% for the monophasic design and 80% for the biphasic design. Both rain garden systems showed excellent removal efficiency of phosphate (89-100%) and atrazine (84-100%). However, significantly (p<0.001) higher removal of nitrate was observed in the biphasic (42-63%) compared to the monophasic rain garden (29-39%). Addition of C substrate in the form of glucose increased removal efficiency of nitrate significantly (p<0.001), achieving up to 87% removal at a treatment C/N ratio of 2.0. This study demonstrates the importance of retention time, environmental conditions (i.e. saturated/unsaturated conditions), and availability of C substrate for bioremediation of pollutants, especially nitrates, in rain gardens.

  8. Numerical Methods and Simulations of Complex Multiphase Flows

    NASA Astrophysics Data System (ADS)

    Brady, Peter

    Multiphase flows are an important part of many natural and technological phenomena such as ocean-air coupling (which is important for climate modeling) and the atomization of liquid fuel jets in combustion engines. The unique challenges of multiphase flow often make analytical solutions to the governing equations impossible and experimental investigations very difficult. Thus, high-fidelity numerical simulations can play a pivotal role in understanding these systems. This dissertation describes numerical methods developed for complex multiphase flows and the simulations performed using these methods. First, the issue of multiphase code verification is addressed. Code verification answers the question "Is this code solving the equations correctly?" The method of manufactured solutions (MMS) is a procedure for generating exact benchmark solutions which can test the most general capabilities of a code. The chief obstacle to applying MMS to multiphase flow lies in the discontinuous nature of the material properties at the interface. An extension of the MMS procedure to multiphase flow is presented, using an adaptive marching tetrahedron style algorithm to compute the source terms near the interface. Guidelines for the use of the MMS to help locate coding mistakes are also detailed. Three multiphase systems are then investigated: (1) the thermocapillary motion of three-dimensional and axisymmetric drops in a confined apparatus, (2) the flow of two immiscible fluids completely filling an enclosed cylinder and driven by the rotation of the bottom endwall, and (3) the atomization of a single drop subjected to a high shear turbulent flow. The systems are simulated numerically by solving the full multiphase Navier-Stokes equations coupled to the various equations of state and a level set interface tracking scheme based on the refined level set grid method. The codes have been parallelized using MPI in order to take advantage of today's very large parallel computational

  9. System maps for retention of small neutral compounds on a superficially porous particle column in reversed-phase liquid chromatography.

    PubMed

    Atapattu, Sanka N; Poole, Colin F; Praseuth, Mike B

    2016-10-14

    The system constants of the solvation parameter model are used to prepare system maps for the retention of small neutral molecules on the ocadecylsiloxane-bonded silica superficially porous particle stationary phase (Kinetex C18) for aqueous-organic solvent mobile phases containing 10-70% (v/v) methanol or acetonitrile. A comparison of the system constants with eight commercially available octadecylsiloxane-bonded silica columns for the same separation conditions confirms that the general retention properties of Kinetex C-18 are similar to totally porous octadecylsiloxane-bonded silica stationary phases and that method transfer should be no more difficult than that usually observed when substituting one octadecylsiloxane-bonded silica column for another.

  10. Portable, lightweight, low power, ion chromatographic system with open tubular capillary columns.

    PubMed

    Kiplagat, Isaac K; Kubán, Petr; Pelcová, Pavlína; Kubán, Vlastimil

    2010-07-30

    Basic operation principles of a lightweight, low power, low cost, portable ion chromatograph utilizing open tubular ion chromatography in capillary columns coated with multi-layer polymeric stationary phases are demonstrated. A minimalistic configuration of a portable IC instrument was developed that does not require any chromatographic eluent delivery system, nor sample injection device as it uses gravity-based eluent flow and hydrodynamic sample injection adopted from capillary electrophoresis. As a detection device, an inexpensive commercially available capacitance sensor is used that has been shown to be a suitable substitute for contactless conductivity detection in capillary separation systems. The built-in temperature sensor allows for baseline drift correction typically encountered in conductivity/capacitance measurements without thermostating device. The whole instrument does not require any power supply for its operation, except the detection and data acquisition part that is provided by a USB port of a Netbook computer. It is extremely lightweight, its total weight including the Netbook computer is less than 2.5kg and it can be continuously operated for more than 8h. Several parameters of the instrument, such as detection cell design, eluent delivery systems and data treatment were optimized as well as the composition of eluent for non-suppressed ion chromatographic analysis of common inorganic cations (Na(+), NH(4)(+), K(+), Cs(+), Ca(2+), Mg(2+), transition metals). Low conductivity eluents based on weakly complexing organic acids such as tartaric, oxalic or pyridine-2,6-dicarboxylic acids were used with contactless capacitance detection for simultaneous separation of mono- and divalent cations. Separation of Na(+) and NH(4)(+) cations was optimized by addition of 18-crown-6 to the eluent. The best separation of 6 metal cations commonly present in various environmental samples was accomplished in less than 30min using a 1.75mM pyridine-2,6-dicarboxylic

  11. Spectrophotometric Microdetermination of Urea in a Rice Wine by Using an Immobilized Acid Urease Column·FIA System

    NASA Astrophysics Data System (ADS)

    Iida, Yasuhiro; Hara, Noriko; Matsumoto, Kunio; Satoh, Ikuo

    Determination of urea in rice wines was performed by using a spectrophotometric flow-injection analysis (FIA) system introducing an acid urease column as a recognition element. An acid urease, having specific properties of showing catalytic activity in low pH range and tolerance to ethanol in comparison to those of a urease from jack-beans, was covalently immobilized onto porous glass beads and then, packed into a small polymer column. This flow-type of the biosensing system was assembled with a sample injection valve, the immobilized enzyme column, a gas-diffusion unit, and a flow-through quartz cell attached to a UV/VIS detector. Standard urea solutions were measured through monitoring variations in absorbance resulting from pH shift due to ammonia molecules enzymatically generated. A wide, linear relationship was obtained between the concentration of urea (7.8 µM - 1.0 mM) and the change in absorbance. Followed by several investigations for application of this FIA system for measurement of urea in commercially available rice wines, the real samples were injected into the FIA system and urea in the samples were determined. These results were compared with those obtained with use of an F-kit method which was widely used for determination of urea. Comparative studies exhibited that this FIA system might be a powerful tool for urea determination in alcoholic beverages.

  12. Modeling multiphase flow using fluctuating hydrodynamics.

    PubMed

    Chaudhri, Anuj; Bell, John B; Garcia, Alejandro L; Donev, Aleksandar

    2014-09-01

    Fluctuating hydrodynamics provides a model for fluids at mesoscopic scales where thermal fluctuations can have a significant impact on the behavior of the system. Here we investigate a model for fluctuating hydrodynamics of a single-component, multiphase flow in the neighborhood of the critical point. The system is modeled using a compressible flow formulation with a van der Waals equation of state, incorporating a Korteweg stress term to treat interfacial tension. We present a numerical algorithm for modeling this system based on an extension of algorithms developed for fluctuating hydrodynamics for ideal fluids. The scheme is validated by comparison of measured structure factors and capillary wave spectra with equilibrium theory. We also present several nonequilibrium examples to illustrate the capability of the algorithm to model multiphase fluid phenomena in a neighborhood of the critical point. These examples include a study of the impact of fluctuations on the spinodal decomposition following a rapid quench, as well as the piston effect in a cavity with supercooled walls. The conclusion in both cases is that thermal fluctuations affect the size and growth of the domains in off-critical quenches.

  13. How Galaxies Acquire their Gas: A Map of Multiphase Accretion and Feedback in Gaseous Galaxy Halos

    NASA Astrophysics Data System (ADS)

    Tumlinson, Jason

    2009-07-01

    We propose to address two of the biggest open questions in galaxy formation - how galaxies acquire their gas and how they return it to the IGM - with a concentrated COS survey of diffuse multiphase gas in the halos of SDSS galaxies at z = 0.15 - 0.35. Our chief science goal is to establish a basic set of observational facts about the physical state, metallicity, and kinematics of halo gas, including the sky covering fraction of hot and cold material, the metallicity of infall and outflow, and correlations with galaxy stellar mass, type, and color - all as a function of impact parameter from 10 - 150 kpc. Theory suggests that the bimodality of galaxy colors, the shape of the luminosity function, and the mass-metallicity relation are all influenced at a fundamental level by accretion and feedback, yet these gas processes are poorly understood and cannot be predicted robustly from first principles. We lack even a basic observational assessment of the multiphase gaseous content of galaxy halos on 100 kpc scales, and we do not know how these processes vary with galaxy properties. This ignorance is presently one of the key impediments to understanding galaxy formation in general. We propose to use the high-resolution gratings G130M and G160M on the Cosmic Origins Spectrograph to obtain sensitive column density measurements of a comprehensive suite of multiphase ions in the spectra of 43 z < 1 QSOs lying behind 43 galaxies selected from the Sloan Digital Sky Survey. In aggregate, these sightlines will constitute a statistically sound map of the physical state and metallicity of gaseous halos, and subsets of the data with cuts on galaxy mass, color, and SFR will seek out predicted variations of gas properties with galaxy properties. Our interpretation of these data will be aided by state-of-the-art hydrodynamic simulations of accretion and feedback, in turn providing information to refine and test such models. We will also use Keck, MMT, and Magellan {as needed} to obtain

  14. Sweet and Sour: Attenuating Sulfidogenesis in an Advective Flow Column System with Perchlorate or Nitrate Treatment

    NASA Astrophysics Data System (ADS)

    Engelbrektson, A. L.; Hubbard, C. G.; Piceno, Y.; Boussina, A.; Jin, Y.; Dubinsky, E. A.; Tom, L.; Hu, P.; Conrad, M. E.; Anderson, G. L.; Coates, J. D.

    2013-12-01

    Hydrogen sulfide (H2S) biogenesis in oil reservoirs is a primary cause of souring and of associated costs in reservoir and pipeline maintenance. In addition to the corrosive effects of the H2S itself, abiotic and biological oxidation also generates sulfuric acid, further degrading metallic surfaces. Amending these environments with perchlorate (ClO4-) resolves these problems by inhibition of biological sulfate reduction and re-oxidation of H2S to elemental sulfur by dissimilatory (per)chlorate reducing bacteria (DPRB). Triplicate flow through columns packed with San Francisco bay sediment were flushed with bay water ([SO4=] = 25-30 mM) containing yeast extract with 50 mM inhibitor concentrations (NO3-or ClO4-) decreasing to 25 mM and finally 12.5 mM. Influent and effluent geochemistry was monitored and DNA was prepared from the sediment bed for microbial community analysis. Souring was reversed by both treatments (at 50 mM) compared to the control columns that had no ion addition. Nitrate began to re-sour when treatment concentration was decreased to 25 mM but treatment had to be decreased to 12.5 mM before the perchlorate treated columns began to re-sour. However, the treated columns re-soured to a lesser extent than the control columns. Phylochip microbial community analyses indicated microbial community shifts and phylogenetic clustering by treatment. Isotopic analysis of sulfate showed trends that broadly agreed with the geochemistry but also suggested further sulfur cycling was occurring. This study indicates that perchlorate shows great promise as an inhibitor of sulfidogenesis in natural communities and provides insight into which organisms are involved in this process.

  15. Direct extraction of tetracyclines from bovine milk using restricted access carbon nanotubes in a column switching liquid chromatography system.

    PubMed

    de Faria, Henrique Dipe; Rosa, Mariana Azevedo; Silveira, Alberto Thalison; Figueiredo, Eduardo Costa

    2017-06-15

    This paper describes, for the first time, the use of restricted access carbon nanotubes (RACNTs) in the analysis of tetracyclines from milk samples, in a multidimensional liquid chromatographic system. Milk samples were initially acidified and centrifuged, and then the supernatant was directly analyzed in a column switching system in backflush configuration employing an extraction column of RACNTs. The sorbent was able to exclude all the remained proteins in less than 2.0min. The method was linear from 50 to 200μgL(-1) and the coefficients of determination (r(2)) were 0.997, 0.992, 0.994 and 0.998 for oxytetracycline (OXI), tetracycline (TC), chlortetracycline (CTC) and doxycycline (DOX), respectively. The analytical range included the maximum residue limits established by the regulatory agency.

  16. Development of Next Generation Multiphase Pipe Flow Prediction Tools

    SciTech Connect

    Cem Sarica; Holden Zhang

    2006-05-31

    The developments of oil and gas fields in deep waters (5000 ft and more) will become more common in the future. It is inevitable that production systems will operate under multiphase flow conditions (simultaneous flow of gas, oil and water possibly along with sand, hydrates, and waxes). Multiphase flow prediction tools are essential for every phase of hydrocarbon recovery from design to operation. Recovery from deep-waters poses special challenges and requires accurate multiphase flow predictive tools for several applications, including the design and diagnostics of the production systems, separation of phases in horizontal wells, and multiphase separation (topside, seabed or bottom-hole). It is crucial for any multiphase separation technique, either at topside, seabed or bottom-hole, to know inlet conditions such as flow rates, flow patterns, and volume fractions of gas, oil and water coming into the separation devices. Therefore, the development of a new generation of multiphase flow predictive tools is needed. The overall objective of the proposed study is to develop a unified model for gas-oil-water three-phase flow in wells, flow lines, and pipelines to predict flow characteristics such as flow patterns, phase distributions, and pressure gradient encountered during petroleum production at different flow conditions (pipe diameter and inclination, fluid properties and flow rates). In the current multiphase modeling approach, flow pattern and flow behavior (pressure gradient and phase fractions) prediction modeling are separated. Thus, different models based on different physics are employed, causing inaccuracies and discontinuities. Moreover, oil and water are treated as a pseudo single phase, ignoring the distinct characteristics of both oil and water, and often resulting in inaccurate design that leads to operational problems. In this study, a new model is being developed through a theoretical and experimental study employing a revolutionary approach. The

  17. High performance mini-gas chromatography-flame ionization detector system based on micro gas chromatography column

    NASA Astrophysics Data System (ADS)

    Zhu, Xiaofeng; Sun, Jianhai; Ning, Zhanwu; Zhang, Yanni; Liu, Jinhua

    2016-04-01

    Monitoring Volatile organic compounds (VOCs) was a very important measure for preventing environmental pollution, therefore, a mini gas chromatography (GC) flame ionization detector (FID) system integrated with a mini H2 generator and a micro GC column was developed for environmental VOC monitoring. In addition, the mini H2 generator was able to make the system explode from far away due to the abandoned use of a high pressure H2 source. The experimental result indicates that the fabricated mini GC FID system demonstrated high repeatability and very good linear response, and was able to rapidly monitor complicated environmental VOC samples.

  18. Column CO2 Measurements with Intensity-Modulated Continuous-Wave Lidar System During the ASCENDS 2014 Summer Field Experiment

    NASA Astrophysics Data System (ADS)

    Meadows, B.; Nehrir, A. R.; Lin, B.; Harrison, F. W.; Dobler, J. T.; Kooi, S. A.; Campbell, J. F.; Obland, M. D.; Browell, E. V.; Yang, M. M.

    2014-12-01

    This paper presents an overview of the ASCENDS 2014 flight campaign results of an intensity-modulated continuous-wave (IM-CW) lidar system operating at 1.57 µm for measurements of column CO2 over a wide variety of geographic regions. The 2007 National Research Council's Decadal Survey of Earth Science and Applications from Space recommended Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) as a mid-term, Tier II, space mission to address global sources, sinks, and transport of atmospheric CO2. As part of the development of a capability for the NASA ASCENDS mission, NASA Langley Research Center (LaRC) and Exelis, Inc. have been collaborating to develop, demonstrate and mature the IM-CW lidar approach for measuring atmospheric column CO2 mixing ratios from a space platform using the integrated path differential absorption (IPDA) lidar technique with preferential weighting of the CO2 measurements to the mid to lower troposphere. The Multi-Functional Fiber Laser Lidar (MFLL), a system developed as a technology demonstrator for the ASCENDS mission, has been used to demonstrate high precision column CO2 retrievals from various aircraft platforms. The MFLL operates using a novel IM-CW IPDA approach to make simultaneous CO2 and O2 column measurements in the 1.57-micron and 1.26-micron spectral regions, respectively, to derive the column-average CO2 dry-air mixing ratios. Measurements from the 2014 summer field experiment focused on advancing CO2 & O2 measurement technologies under day and night conditions in realistic environments, assessing CO2 emissions over large metropolitan areas, observing and evaluating CO2 drawdown and diurnal trends over large agricultural regions, obtaining reflectance data and CO2 & O2 measurements over rough ocean surfaces with high surface wind speeds (~10 m/s), and carrying out CO2 & O2 intercomparisons with OCO-2 and GOSAT over the western United States. Initial results from MFLL for the aforementioned flight campaign

  19. Synaptic circuits and their variations within different columns in the visual system of Drosophila.

    PubMed

    Takemura, Shin-ya; Xu, C Shan; Lu, Zhiyuan; Rivlin, Patricia K; Parag, Toufiq; Olbris, Donald J; Plaza, Stephen; Zhao, Ting; Katz, William T; Umayam, Lowell; Weaver, Charlotte; Hess, Harald F; Horne, Jane Anne; Nunez-Iglesias, Juan; Aniceto, Roxanne; Chang, Lei-Ann; Lauchie, Shirley; Nasca, Ashley; Ogundeyi, Omotara; Sigmund, Christopher; Takemura, Satoko; Tran, Julie; Langille, Carlie; Le Lacheur, Kelsey; McLin, Sari; Shinomiya, Aya; Chklovskii, Dmitri B; Meinertzhagen, Ian A; Scheffer, Louis K

    2015-11-03

    We reconstructed the synaptic circuits of seven columns in the second neuropil or medulla behind the fly's compound eye. These neurons embody some of the most stereotyped circuits in one of the most miniaturized of animal brains. The reconstructions allow us, for the first time to our knowledge, to study variations between circuits in the medulla's neighboring columns. This variation in the number of synapses and the types of their synaptic partners has previously been little addressed because methods that visualize multiple circuits have not resolved detailed connections, and existing connectomic studies, which can see such connections, have not so far examined multiple reconstructions of the same circuit. Here, we address the omission by comparing the circuits common to all seven columns to assess variation in their connection strengths and the resultant rates of several different and distinct types of connection error. Error rates reveal that, overall, <1% of contacts are not part of a consensus circuit, and we classify those contacts that supplement (E+) or are missing from it (E-). Autapses, in which the same cell is both presynaptic and postsynaptic at the same synapse, are occasionally seen; two cells in particular, Dm9 and Mi1, form ≥ 20-fold more autapses than do other neurons. These results delimit the accuracy of developmental events that establish and normally maintain synaptic circuits with such precision, and thereby address the operation of such circuits. They also establish a precedent for error rates that will be required in the new science of connectomics.

  20. Critical evaluation and comparison of fluid distribution systems for industrial scale expanded bed adsorption chromatography columns.

    PubMed

    Arpanaei, A; Heebøll-Nielsen, A; Hubbuch, J J; Thomas, O R T; Hobley, T J

    2008-07-11

    The hydrodynamic properties of an expanded bed contactor with 30 cm or 150 cm internal diameter, which employs a rotating or oscillating fluid distributor, were compared to prototype columns of 60 cm or 150 cm diameter employing local stirring (fixed wall nozzles plus central bottom mounted stirrer) for fluid distribution. Fluid introduction through a rotating fluid distributor was found to give superior hydrodynamic characteristics in the 30 cm and 150 cm diameter column compared to using the local stirrer in both the 60 cm and 150 cm diameter columns. The shortcomings of the local stirring distributor at large scale were apparent: dead zones were present which could not be removed by increasing rotation rates or flow rates, and such changes led to a deterioration in hydrodynamic properties. In contrast, during fluid introduction through a rotating distributor no dead zones were observed, and residence time distribution tests showed that plate numbers remained constant or increased slightly as flow rate was raised from 200 cm h(-1) to 470 cm h(-1). Under the conditions studied, oscillation of the rotating fluid distributor led to increased mixing and poorer performance than rotary movement. The results imply that further improvement in distributor design is needed and careful attention should be given to the trade off between turbulence and adequate fluid distribution.

  1. Assessing the removal potential of soil-aquifer treatment system (soil column) for endotoxin.

    PubMed

    Guizani, Mokhtar; Kato, Hideaki; Funamizu, Naoyuki

    2011-06-01

    Soil-aquifer treatment (SAT) of wastewater is an increasingly valued practice for replenishing aquifers due to ease of operation and low maintenance needs and therefore low cost. In this study, we investigated the fate of endotoxins through laboratory-scale SAT soil columns over a four month period. The effluent of rapid sand filtration was run through the columns under gravity flow conditions. Four SAT columns were packed with four different filter materials (fine sand, medium sand, coarse sand and very coarse sand). The effluent of rapid sand filtration (average dissolved organic carbon (DOC) = 4 mg l(-1) and average endotoxin concentration = 4 EU ml(-1)) was collected from a domestic wastewater treatment plant in Sapporo, Japan. DOC removal ranged from 12.5% to greater than 22.5% during the study, with DOC levels averaging 3.1 and 3.5 mg l(-1) for the SAT columns packed with different soils. Endotoxin transformation exhibited different profiles, depending on the time and soil type. Reduction in endotoxin concentration averaged 64.3% and was as high as 86.7% across the soil columns 1, 2, 3 and 4, respectively. While DOC removal was gradual, the reductions in endotoxin levels were rather rapid and most of the removal was achieved in the top layers. Soil with a larger grain size had lower efficiency in removing endotoxin. Tests were performed to evaluate the transformation of organic matter showing endotoxicity and to determine the mechanisms responsible for changes in the structural and size properties of dissolved organic matter (OM) during SAT. Dissolved OM was fractionated using Sep-Pack C18 Cartridges into hydrophobic and hydrophilic fractions. Dialysis tubes with different molecular weight cut-offs were used to perform size fractions of OM showing endotoxicity. Evaluation of the transformation of organic matter showing endotoxicity during SAT indicated that both hydrophobic and large molecules were reduced. Moreover, experimental findings showed that

  2. Separation of transition metals on a poly-iminodiacetic acid grafted polymeric resin column with post-column reaction detection utilising a paired emitter-detector diode system.

    PubMed

    Barron, Leon; O'Toole, Martina; Diamond, Dermot; Nesterenko, Pavel N; Paull, Brett

    2008-12-05

    The selectivity, retention and separation of transition metals on a short (2 mm x 50 mm) column packed with a poly-iminodiacetic acid functionalised polymer 10 microm resin (Dionex ProPac IMAC-10) are presented. This stationary phase, typically used for the separation of proteins, is composed of long chain poly-iminodiacetic acid groups grafted to a hydrophilic layer surrounding a 10 microm polymeric bead. Through the use of a combination of a multi-step pH and picolinic acid gradient, the separation of magnesium, iron, cobalt, cadmium, zinc, lead and copper was possible, followed by post-column reaction with 4-(2-pyridylazo) resorcinol (PAR) and absorbance detection at 510 nm using a novel and inexpensive optical detector, comprised of two light emitting diodes with one acting as a light source and the other as a detector. Column efficiency for selective transition metals was in excess of N=10,000, with the baseline separation of seven metal cations in <3 min possible under optimised conditions. Detection limits of between 5 and 81 microg/L were possible based upon a 50 microL injection volume.

  3. Multiphase complete exchange on Paragon, SP2 and CS-2

    NASA Technical Reports Server (NTRS)

    Bokhari, Shahid H.

    1995-01-01

    The overhead of interprocessor communication is a major factor in limiting the performance of parallel computer systems. The complete exchange is the severest communication pattern in that it requires each processor to send a distinct message to every other processor. This pattern is at the heart of many important parallel applications. On hypercubes, multiphase complete exchange has been developed and shown to provide optimal performance over varying message sizes. Most commercial multicomputer systems do not have a hypercube interconnect. However, they use special purpose hardware and dedicated communication processors to achieve very high performance communication and can be made to emulate the hypercube quite well. Multiphase complete exchange has been implemented on three contemporary parallel architectures: the Intel Paragon, IBM SP2 and Meiko CS-2. The essential features of these machines are described and their basic interprocessor communication overheads are discussed. The performance of multiphase complete exchange is evaluated on each machine. It is shown that the theoretical ideas developed for hypercubes are also applicable in practice to these machines and that multiphase complete exchange can lead to major savings in execution time over traditional solutions.

  4. Applying uncertainty quantification to multiphase flow computational fluid dynamics

    SciTech Connect

    Gel, A; Garg, R; Tong, C; Shahnam, M; Guenther, C

    2013-07-01

    Multiphase computational fluid dynamics plays a major role in design and optimization of fossil fuel based reactors. There is a growing interest in accounting for the influence of uncertainties associated with physical systems to increase the reliability of computational simulation based engineering analysis. The U.S. Department of Energy's National Energy Technology Laboratory (NETL) has recently undertaken an initiative to characterize uncertainties associated with computer simulation of reacting multiphase flows encountered in energy producing systems such as a coal gasifier. The current work presents the preliminary results in applying non-intrusive parametric uncertainty quantification and propagation techniques with NETL's open-source multiphase computational fluid dynamics software MFIX. For this purpose an open-source uncertainty quantification toolkit, PSUADE developed at the Lawrence Livermore National Laboratory (LLNL) has been interfaced with MFIX software. In this study, the sources of uncertainty associated with numerical approximation and model form have been neglected, and only the model input parametric uncertainty with forward propagation has been investigated by constructing a surrogate model based on data-fitted response surface for a multiphase flow demonstration problem. Monte Carlo simulation was employed for forward propagation of the aleatory type input uncertainties. Several insights gained based on the outcome of these simulations are presented such as how inadequate characterization of uncertainties can affect the reliability of the prediction results. Also a global sensitivity study using Sobol' indices was performed to better understand the contribution of input parameters to the variability observed in response variable.

  5. Multiphase pump field trials demonstrate practical applications for the technology

    SciTech Connect

    Dal Porto, D.F.; Larson, L.A.

    1996-12-31

    The results of two multiphase pump field trials are presented. One field trial was conducted offshore on a platform in the Gulf of Mexico (GOM). It is a low pressure boost (100 psi) application involving gas lifted wells. The other field trial was conducted onshore in an oil field in Alberta, Canada. This multiphase pump was designed for a high pressure boost (850 psi) capability with primarily rod pumped wells feeding the suction of the pump. The offshore pump was sized to handle the flow from one well. By lowering the back-pressure on the well, increased production was realized. The increased flow from one of the wells far surpassed the predicted quantity. Early problems with the double mechanical seal system were overcome and a new, simplified single mechanical seal system has been designed and installed. The onshore multiphase pump clearly demonstrated that a twin screw pump can operate reliably in a field environment, even under severe slug flow conditions. The trial indicated that a considerable portion of the liquid in the recycle stream (required because of the high gas fraction of the multiphase fluid from the field) flashes into gas which occupies more volume in the pump than if it remained liquid. This decreased the capability of the pump to handle net flow from the field. These conditions motivated a re-evaluation of the pump sizing techniques. Performance data and lessons learned information are presented for both field trials.

  6. Distillation Column Flooding Predictor

    SciTech Connect

    George E. Dzyacky

    2010-11-23

    /vapor traffic that produce increased contact area and lead to substantial increases in separation efficiency – which translates to a 10% increase in energy efficiency on a BTU/bbl basis. The Flooding Predictor™ operates on the principle that between five to sixty minutes in advance of a flooding event, certain column variables experience an oscillation, a pre-flood pattern. The pattern recognition system of the Flooding Predictor™ utilizes the mathematical first derivative of certain column variables to identify the column’s pre-flood pattern(s). This pattern is a very brief, highly repeatable, simultaneous movement among the derivative values of certain column variables. While all column variables experience negligible random noise generated from the natural frequency of the process, subtle pre-flood patterns are revealed among sub-sets of the derivative values of column variables as the column approaches its hydraulic limit. The sub-set of column variables that comprise the pre-flood pattern is identified empirically through in a two-step process. First, 2ndpoint’s proprietary off-line analysis tool is used to mine historical data for pre-flood patterns. Second, the column is flood-tested to fine-tune the pattern recognition for commissioning. Then the Flooding Predictor™ is implemented as closed-loop advanced control strategy on the plant’s distributed control system (DCS), thus automating control of the column at its hydraulic limit.

  7. Chlorophyll-a thin layers in the Magellan fjord system: The role of the water column stratification

    NASA Astrophysics Data System (ADS)

    Ríos, Francisco; Kilian, Rolf; Mutschke, Erika

    2016-08-01

    Fjord systems represent hotspots of primary productivity and organic carbon burial. However, the factors which control the primary production in mid-latitude fjords are poorly understood. In this context, results from the first fine-scale measurements of bio-oceanographic features in the water column of fjords associated with the Strait of Magellan are presented. A submersible fluorescence probe (FP) was used to measure the Chlorophyll-a (Chl-a) concentration in situ, along with conductivity, temperature, hydrostatic pressure (depth) and dissolved oxygen (CTD-O2) of the water column. The Austral spring results of 14 FP-CTD-O2 profiles were used to define the vertical and horizontal patches of the fluorescent pigment distribution and their spatial relations with respect to the observed hydrographic features. Three zones with distinct water structures were defined. In all zones, the 'brown' spectral group (diatoms and dinoflagellates) predominated accounting for >80 wt% of the phytoplankton community. Thin layers with high Chl-a concentration were detected in 50% of the profiles. These layers harbored a substantial amount (30-65 wt%) of the phytoplankton biomass. Stratification was positively correlated to the occurrence of Chl-a thin layers. In stable and highly stratified water columns the integrated Chl-a concentration was higher and frequently located within thin layers whereas well mixed water columns displayed lower values and more homogeneous vertical distribution of Chl-a. These results indicate that mixing/stability processes are important factors accounting to the vertical distribution of Chl-a in Magellan fjords.

  8. Testing and analysis of magnetorheological fluid sedimentation in a column using a vertical axis inductance monitoring system

    NASA Astrophysics Data System (ADS)

    Choi, Young-Tai; Xie, Lei; Wereley, Norman M.

    2016-04-01

    This study investigates the sedimentation of magnetorheological fluids (MRFs) in a vertical column using a vertical axis inductance monitoring system (VAIMS). The particle concentration (i.e., particle volume fraction) of MRF samples consisting of carbonyl iron powder in a silicone carrier fluid was monitored as a function of column height for 156 h with a measurement nominally every 12 h. In addition, the extent and concentration gradients in four distinct sedimentation zones were monitored: supernatant zone, original concentration zone, variable concentration zone, and sediment zone. In order to obtain the settling velocity of the MRF with respect to particle concentration, MRF samples with different volume fractions (i.e., 15, 19, 26, 30 and 40 vol%) were synthesized, and mudline (i.e., the boundary between clarified supernatant fluid zone and the original concentration zone below) descent of each sample was measured using both the VAIMS and visual observation. In this study, three different settling velocity models (i.e., Vesilind, Richardson and Zaki, and Dick models) were considered in order to capture settling velocity as a function of concentration. Vesilind’s settling velocity model was found to be most suitable for the MRF sample in our study, and the setting velocity distribution in the vertical column could be measured for each MRF sample. Based on Kynch’s sedimentation analysis, the mass balance equation was obtained and integrated with Vesilind’s settling velocity model to obtain the concentration propagation velocity. In addition, the solids flux within the fluid column was obtained to provide insight in sedimentation stability as a function of particle concentration.

  9. An OAIS-based Hospital Information System on the Cloud: Analysis of a NoSQL Column-Oriented Approach.

    PubMed

    Celesti, Antonio; Maria, Fazio; Romano, Agata; Bramanti, Alessia; Bramanti, Placido; Villari, Massimo

    2017-03-10

    The Open Archive Information System (OAIS) is a reference model for organizing people and resources in a system, and it is already adopted in care centers and medical systems to efficiently manage clinical data, medical personnel and patients. Archival storage systems are typically implemented using traditional relational database systems, but the relation-oriented technology strongly limits the efficiency in the management of huge amount of patients' clinical data, especially in emerging Cloud-based, that are distributed. In this paper, we present an OAIS healthcare architecture usefull to manage a huge amount of HL7 clinical documents in a scalable way. Specifically, it is based on a NoSQL column-oriented Data Base Management System (DBMS) deployed in the Cloud, thus to benefit from a big tables and wide rows available over a virtual distributed infrastructure. We developed a prototype of the proposed architecture at the IRCCS, and we evaluated its efficiency in a real case of study.

  10. Performance of Goddard Earth Observing System GCM Column Radiation Models under Heterogeneous Cloud Conditions

    NASA Technical Reports Server (NTRS)

    Oreopoulos, L.; Chou, M.-D.; Khairoutdinov, M.; Barker, H. W.; Cahalan, R. F.

    2003-01-01

    We test the performance of the shortwave (SW) and longwave (LW) Column Radiation Models (CORAMs) of Chou and collaborators with heterogeneous cloud fields from a global single-day dataset produced by NCAR's Community Atmospheric Model with a 2-D CRM installed in each gridbox. The original SW version of the CORAM performs quite well compared to reference Independent Column Approximation (ICA) calculations for boundary fluxes, largely due to the success of a combined overlap and cloud scaling parameterization scheme. The absolute magnitude of errors relative to ICA are even smaller for the LW CORAM which applies similar overlap. The vertical distribution of heating and cooling within the atmosphere is also simulated quite well with daily-averaged zonal errors always below 0.3 K/d for SW heating rates and 0.6 K/d for LW cooling rates. The SW CORAM's performance improves by introducing a scheme that accounts for cloud inhomogeneity. These results suggest that previous studies demonstrating the inaccuracy of plane-parallel models may have unfairly focused on worst scenario cases, and that current radiative transfer algorithms of General Circulation Models (GCMs) may be more capable than previously thought in estimating realistic spatial and temporal averages of radiative fluxes, as long as they are provided with correct mean cloud profiles. However, even if the errors of the particular CORAMs are small, they seem to be systematic, and the impact of the biases can be fully assessed only with GCM climate simulations.

  11. Burdach's column.

    PubMed

    Pearce, J M S

    2006-01-01

    After the Greek physicians Herophilus and Galen, the major anatomical advances in the anatomy of the spinal cord were made possible by the microtome devised by Benedikt Stilling in January 1842. This enabled him to cut the frozen, thin sections and examine them, unstained,with the microscope. The technique founded future investigation of the cord's anatomy. Brown-Séquard, Türck, Clarke, Lissauer, Goll, and Flechsig all contributed. An important result of these progressing anatomical experiments was the identification of the posterior columns. In 1826, the German physiologist Karl Friedrich Burdach (1776-1847) described, from macroscopic study, the fasciculus cuneatus, known as the tract of Burdach: the lateral portion of the posterior columns of the cord that terminate in the nucleus cuneatus of the medulla.

  12. Development of an Exhaled Breath Monitoring System with Semiconductive Gas Sensors, a Gas Condenser Unit, and Gas Chromatograph Columns

    PubMed Central

    Itoh, Toshio; Miwa, Toshio; Tsuruta, Akihiro; Akamatsu, Takafumi; Izu, Noriya; Shin, Woosuck; Park, Jangchul; Hida, Toyoaki; Eda, Takeshi; Setoguchi, Yasuhiro

    2016-01-01

    Various volatile organic compounds (VOCs) in breath exhaled by patients with lung cancer, healthy controls, and patients with lung cancer who underwent surgery for resection of cancer were analyzed by gas condenser-equipped gas chromatography-mass spectrometry (GC/MS) for development of an exhaled breath monitoring prototype system involving metal oxide gas sensors, a gas condenser, and gas chromatography columns. The gas condenser-GC/MS analysis identified concentrations of 56 VOCs in the breath exhaled by the test population of 136 volunteers (107 patients with lung cancer and 29 controls), and selected four target VOCs, nonanal, acetoin, acetic acid, and propanoic acid, for use with the condenser, GC, and sensor-type prototype system. The prototype system analyzed exhaled breath samples from 101 volunteers (74 patients with lung cancer and 27 controls). The prototype system exhibited a level of performance similar to that of the gas condenser-GC/MS system for breath analysis. PMID:27834896

  13. Development of an Exhaled Breath Monitoring System with Semiconductive Gas Sensors, a Gas Condenser Unit, and Gas Chromatograph Columns.

    PubMed

    Itoh, Toshio; Miwa, Toshio; Tsuruta, Akihiro; Akamatsu, Takafumi; Izu, Noriya; Shin, Woosuck; Park, Jangchul; Hida, Toyoaki; Eda, Takeshi; Setoguchi, Yasuhiro

    2016-11-10

    Various volatile organic compounds (VOCs) in breath exhaled by patients with lung cancer, healthy controls, and patients with lung cancer who underwent surgery for resection of cancer were analyzed by gas condenser-equipped gas chromatography-mass spectrometry (GC/MS) for development of an exhaled breath monitoring prototype system involving metal oxide gas sensors, a gas condenser, and gas chromatography columns. The gas condenser-GC/MS analysis identified concentrations of 56 VOCs in the breath exhaled by the test population of 136 volunteers (107 patients with lung cancer and 29 controls), and selected four target VOCs, nonanal, acetoin, acetic acid, and propanoic acid, for use with the condenser, GC, and sensor-type prototype system. The prototype system analyzed exhaled breath samples from 101 volunteers (74 patients with lung cancer and 27 controls). The prototype system exhibited a level of performance similar to that of the gas condenser-GC/MS system for breath analysis.

  14. Germanium multiphase equation of state

    SciTech Connect

    Crockett, Scott D.; Lorenzi-Venneri, Giulia De; Kress, Joel D.; Rudin, Sven P.

    2014-05-07

    A new SESAME multiphase germanium equation of state (EOS) has been developed using the best available experimental data and density functional theory (DFT) calculations. The equilibrium EOS includes the Ge I (diamond), the Ge II (β-Sn) and the liquid phases. The foundation of the EOS is based on density functional theory calculations which are used to determine the cold curve and the Debye temperature. Results are compared to Hugoniot data through the solid-solid and solid-liquid transitions. We propose some experiments to better understand the dynamics of this element

  15. Report on Multiphase Flow Panel

    NASA Technical Reports Server (NTRS)

    2003-01-01

    This paper presents viewgraphs on a multiphase flow panel. The topics include: 1) Discussion of Priorities; 2) Critical Issues Reduced Gravity Instabilities; 3) Severely Limiting Phase Separation; 4) Severely-Limiting Phase Change; 5) Enhancements; 6) Awareness Instabilities; 7) Awareness; 8) Methods of Resolution; 9) 2008 Space Flight; 10) 2003-2008 Ground-Based Microgravity Facilities; 11) 2003-2008 Other; 12) 2009-2015 Space Flight; 13) 2009-2015 Ground-Based Microgravity Facilities; 14) 2009-2015 Other; and 15) 2016.

  16. Germanium multiphase equation of state

    NASA Astrophysics Data System (ADS)

    Crockett, S. D.; De Lorenzi-Venneri, G.; Kress, J. D.; Rudin, S. P.

    2014-05-01

    A new SESAME multiphase germanium equation of state (EOS) has been developed utilizing the best available experimental data and density functional theory (DFT) calculations. The equilibrium EOS includes the Ge I (diamond), the Ge II (β-Sn) and the liquid phases. The foundation of the EOS is based on density functional theory calculations which are used to determine the cold curve and the Debye temperature. Results are compared to Hugoniot data through the solid-solid and solid-liquid transitions. We propose some experiments to better understand the dynamics of this element.

  17. Germanium Multiphase Equation of State

    NASA Astrophysics Data System (ADS)

    Crockett, Scott; Kress, Joel; Rudin, Sven; de Lorenzi-Venneri, Giulia

    2013-06-01

    A new SESAME multiphase Germanium equation of state (EOS) has been developed utilizing the best experimental data and theoretical calculations. The equilibrium EOS includes the GeI (diamond), GeII (beta-Sn) and liquid phases. We will also explore the meta-stable GeIII (tetragonal) phase of germanium. The theoretical calculations used in constraining the EOS are based on quantum molecular dynamics and density functional theory phonon calculations. We propose some physics rich experiments to better understand the dynamics of this element.

  18. Turbulent Mixing of Multiphase Flow

    NASA Technical Reports Server (NTRS)

    Young, Y.-N.; Ferziger, J.; Ham, F. E.; Herrmann, M.

    2003-01-01

    Thus we conduct numerical simulations of multiphase fluids stirred by two-dimensional turbulence to assess the possibility of self-similar drop size distribution in turbulence. In our turbulence simulations, we also explore the non-diffusive limit, where molecular mobility for the interface is vanishing. Special care is needed to transport the non-diffusive interface. Numerically, we use the particle level set method to evolve the interface. Instead of using the usual methods to calculate the surface tension force from the level set function, we reconstruct the interface based on phase- field modeling, and calculate the continuum surface tension forcing from the reconstructed interface.

  19. Feasibility study on wave energy power plant with oscillating water column system in Bawean Island Seas Indonesia

    NASA Astrophysics Data System (ADS)

    Ali, A. F.; Hadi, S.

    2016-03-01

    As a huge archipelago with 17,480 islands, Indonesia still has difficulties to electrify all of its islands especially on the remote ones (areas) because of a power grid coverage limitation of National Electrical Company (PLN). This research discusses the potential calculation of sea wave power conversion by utilizing Oscillating Water Column (OWC) system in remote islands, especially on Bawean Island Seas. OWC system is chosen because of its advantages compared to other systems and also because of its suitability towards sea and coast areas in Indonesia. Kim Nielsen and David Ross Law were used for the power calculation. The research took data sampling during one month in 2015 with the result of wave height average of 2.09 meters. That obtained data resulted wave energy of within 270.19 and electrical power output of about 52.7 kW by using Oscillating Water Column system. Based on this result, Break Even Point (BEP) for one plant covering 117 houses will become zero in the period of 3 years 8 months.

  20. Performance limits and kinetic optimization of parallel and serially connected multi-column systems spanning a wide range of efficiencies for liquid chromatography.

    PubMed

    Cabooter, Deirdre; Desmet, Gert

    2012-01-06

    Using a set of experimentally determined liquid chromatography column performance data, it has been investigated how a range of efficiencies can best be covered when using a multi-column system. Two main variants are considered: a serially-connected variant (realizing different column lengths by connecting a different number of column segments in series) and a parallel-connected variant (realizing different column lengths by simply switching between columns with a different length arranged in parallel). Both variants are compared for their ability to keep the average analysis time along a given range of efficiencies as close as possible to the intrinsic Knox & Saleem-speed limit. It was found that the serial connection mode offers a better compromise between average speed and amount of required silica (total required column length) than the parallel connection mode for all efficiency ranges running from 5000-10,000 plates up to 75,000-150,000 plates. Considering an ultra-high performance liquid chromatography (UHPLC) operation at 1200 bar, the best possible serial connection system can get within about within 15-25% of the Knox & Saleem-speed limit, whereas a three-column parallel system can only get to within 40-50% of the speed limit, while needing 50-100% more total column length. In absolute terms, the serially-connected system with individually optimized segment lengths should be able to cover a range of 5000-75,000 theoretical plates (dynamic range of 25) in an average analysis time of 14.3 min when using a 1200 bar instrument. At 400 bar, this would be 37.9 min, showing that the construction of wide-efficiency range systems would be one of the application areas where the advantages of UHPLC-conditions would be most fully realized.

  1. The experience from field operation of a subsea multiphase booster

    SciTech Connect

    De Donno, S.; Colombi, P.; Chiesa, G.; Ferrari Aggradi, G.

    1995-12-31

    The subsea multiphase production -- based on the transportation over long distance of the untreated oil-well fluids (oil, water and gas) -- is expected to be one of the most efficient tool for economic exploitation of deep offshore and marginal fields. A long term testing campaign on a multiphase screw pump was successfully completed in 1990 at the AGIP Trecate onshore oil field and the results confirmed the industrial viability for such a kind of equipment for surface application. Then, a subsea version of an improved multiphase twin screw pump has been integrated into a Subsea Multiphase Boosting Unit and installed on the Prezioso Field, offshore Sicily, in Summer 1994. Long term testing under real operating conditions were initiated after a successful start-up of the Unit. To the Authors` knowledge, this is the first world-wide subsea installation of an electrically driven multiphase pump operating with live oil. The paper presents first a description of the marine twin screw pump concept adopted for the subsea application including the main features of the complete boosting unit and the adopted solutions to allow it to operate under different conditions. Then, the project implementation activities from the onshore integration through the installation, commissioning and start-up operations are described. Moreover, the results of the initial functional tests are discussed with particular reference to the screw pump hydraulic performance as well as to the behavior of the pump pressure compensation and seal/lube oil systems. Transient and steady state conditions experienced by the system are finally characterized and the early evidences of its long term performance are discussed.

  2. Cr(VI) removal from aqueous systems using pyrite as the reducing agent: batch, spectroscopic and column experiments.

    PubMed

    Kantar, Cetin; Ari, Cihan; Keskin, Selda; Dogaroglu, Zeynep Gorkem; Karadeniz, Aykut; Alten, Akin

    2015-03-01

    Laboratory batch and column experiments, in conjunction with geochemical calculations and spectroscopic analysis, were performed to better understand reaction mechanisms and kinetics associated with Cr(VI) removal from aqueous systems using pyrite as the reactive material under both static and dynamic flow conditions similar to those observed in in situ permeable reactive barriers (PRBs). The X-ray photoelectron spectroscopy (XPS) and geochemical calculations suggest that the Cr(VI) removal by pyrite occurred due to the reduction of Cr(VI) to Cr(III), coupled with the oxidation of Fe(II) to Fe(III) and S2(2-) to SO4(2-) at the pyrite surface. Zeta potential measurements indicate that although the pyrite surface was negatively charged under a wide pH range in the absence of Cr(VI), it behaved more like a "metal oxide" surface with the surface potential shifting from positive to negative values at pH values >pH 6 in the presence of Cr(VI). Batch experiments show that increasing solution pH led to a significant decrease in Cr(VI) removal. The decrease in Cr(VI) removal at high Cr(VI) concentrations and pH values can be explained through the precipitation of sparingly soluble Cr(OH)(3(s)), Fe(OH)(3(s)) and Fe(III)-Cr(III) (oxy) hydroxides onto pyrite surface which may, then, lead to surface passivation for further Cr(VI) reduction. Batch results also suggest that the reaction kinetics follow a first order model with rate constants decreasing with increasing solution pH, indicating proton consumption during Cr(VI) reduction by pyrite. Column experiments indicate that nearly 100% of total Fe in the column effluent was in the form of Fe(II) species with a [SO4(2-)]/[Fe(2+)] stoichiometric ratio of 2.04, indicating that the reduction of Cr(VI) by pyrite produced about 2 mol of sulfate per mole of Fe (II) release under excess surface sites relative to Cr(VI) concentration. Column experiments provide further evidence on the accumulation of oxidation products which

  3. Azo Dyes and Their Interfacial Activity: Implications for Multiphase Flow Experiments

    SciTech Connect

    Tuck, D.M.

    1999-04-21

    Interfacial effects play an important role in governing multiphase fluid behavior in porous media (Neustadter 1984; Tuck et al. 1988). For instance, several dimensionless numbers have been developed to express important force ratios applicable to multiphase flow in porous media (Morrow and Songkran 1981; Chatzis and Morrow 1984; Wardlaw 1988; Pennell et al. 1996; Dawson and Roberts 1997). These force ratios emphasize the importance of interfacial properties. Our objectives are to provide chemical information regarding the dyes commonly used in multiphase flow visualization studies and to show the surface chemistry effects of the most commonly used dye, Sudan IV, in the tetrachloroethylene (PCE)-water-glass system

  4. Development of the maypole (hoop/column) deployable reflector concept for large space systems application

    NASA Technical Reports Server (NTRS)

    Montgomery, D. C.

    1981-01-01

    A review of the NASA supplied mission scenarios for the communications, radiometry and radio astronomy missions. Led to specific hoop/column antenna configurations for each mission. The mission configurations were then evaluated to identify specific technology items requiring further development. The compilation of these technology drivers resulted in a specification of an artificial or point design, the design element around which all design and performance estimates for the rest of the program were made. Mechanisms for deployment and stowing are examined including the cable driven mast and the latch pulley roller. Methods for determining the thermal expansion of candidate materials, the development of the cables, cords, and hinged joints, and surface adjustment are considered.

  5. A sensitive post-column photochemical derivatization/fluorimetric detection system for HPLC determination of bisphosphonates.

    PubMed

    Pérez-Ruiz, Tomás; Martínez-Lozano, Carmen; García-Martínez, María Dolores

    2009-02-27

    A new reversed-phase ion-pair high-performance liquid chromatographic (HPLC) method has been developed for the determination of the following bisphosphonic acids: alendronic acid (ALEN), etidronic acid (ETID), ibandronic acid (IBAN) and risedronic acid (RISE). Separation was achieved on a C(18) column using a mixture of 50 mmol L(-1) borate buffer pH 9.0 containing 0.25 mmol L(-1) tetrabutylammonium chloride and 0.5 mmol L(-1) EDTA and acetonitrile (97:3) as the mobile phase. The sensitive detection of the above bisphosphonic acids was based on their oxidation to orthophosphate by the on-line peroxydisulfate-assisted photolysis followed by post-column reaction with molybdate to yield phosphomolybdate. This subsequently reacted with thiamine to generate thiochrome and, finally, the fluorescence of thiochrome was measured at 440 nm with excitation at 375 nm. The developed method is precise with a mean relative standard deviation of 1.3%, sensitive (with a detection limit at the nmol L(-1) level), accurate, specific, rapid (analysis time approximately 13 min) and inexpensive because to the low cost of the reagents. The assay was applied to the analysis of the four bisphosphonic acids in commercial dosage formulations, in which the excipients did not interfere with the determination. The method was also applied to the determination of etidronate, risedronate and ibandronate in human urine. Sample preparation involves precipitation of the analytes from urine along with endogenous phosphates such as calcium salts by addition of calcium chloride at alkaline pH and dissolution of the precipitate in 0.05 mol L(-1) ethylene glycol-bis(beta-aminoethyl ether)-N,N,N',N'-tetraacetic acid.

  6. Multiphase flows in confinement with complex geometries

    NASA Astrophysics Data System (ADS)

    Aymard, Benjamin; Pradas, Marc; Vaes, Urbain; Kalliadasis, Serafim

    2016-11-01

    Understanding the dynamics of immiscible fluids in confinement is crucial in numerous applications such as oil recovery, fuel cells and the rapidly growing field of microfluidics. Complexities such as microstructures, chemical-topographical heterogeneities or porous membranes, can often induce non-trivial effects such as critical phenomena and phase transitions . The dynamics of confined multiphase flows may be efficiently described using diffuse-interface theory, leading to the Cahn-Hilliard-Navier-Stokes(CHNS) equations with Cahn wetting boundary conditions. Here we outline an efficient numerical method to solve the CHNS equations using advanced geometry-capturing mesh techniques both in two and three dimensional scenarios. The methodology is applied to two different systems: a droplet on a spatially chemical-topographical heterogeneous substrateand a microfluidic separator.

  7. Modeling hyperelasticity in non-equilibrium multiphase flows

    NASA Astrophysics Data System (ADS)

    Hank, Sarah; Favrie, Nicolas; Massoni, Jacques

    2017-02-01

    The aim of this article is the construction of a multiphase hyperelastic model. The Eulerian formulation of the hyperelasticity represents a system of 14 conservative partial differential equations submitted to stationary differential constraints. This model is constructed with an elegant approach where the specific energy is given in separable form. The system admits 14 eigenvalues with 7 characteristic eigenfields. The associated Riemann problem is not easy to solve because of the presence of 7 waves. The shear waves are very diffusive when dealing with the full system. In this paper, we use a splitting approach to solve the whole system using 3 sub-systems. This method reduces the diffusion of the shear waves while allowing to use a classical approximate Riemann solver. The multiphase model is obtained by adapting the discrete equations method. This approach involves an additional equation governing the evolution of a phase function relative to the presence of a phase in a cell. The system is integrated over a multiphase volume control. Finally, each phase admits its own equations system composed of three sub-systems. One and three dimensional test cases are presented.

  8. Removal of copper and iron by polyurethane foam column in FIA system for the determination of nickel in pierced ring.

    PubMed

    Vongboot, Monnapat; Suesoonthon, Monrudee

    2015-01-01

    Polyurethane foam (PUF) mini-column was used to eliminate copper and iron for the determination of nickel in pierced rings. The PUF mini-column was connected to FIA system for on-line sorption of copper and iron in complexes form of CuSCN(+) and FeSCN(2+). For this season, the acid solution containing a mixture of Ni(II), Fe(III), Cu(II) and SCN(-) ions was firstly flew into the PUF column. Then, the percolated solution which Fe(III) and Cu(II) ions is separated from analysis was injected into FIA system to react with 4-(2-pyridylazo) resorcinol (PAR) reagent in basic condition which this method is called pH gradient technique. The Ni-PAR complexes obtained were measured theirs absorbance at 500 nm by UV visible spectrophotometer. In this study, it was found that Cu(II) and Fe(III) were completely to form complexes with 400 mmol/L KSCN and entirely to eliminate in acidic condition at pH 3.0. In the optimum condition of these experiments, the method provided the linear relationship between absorbance and the concentration of Ni(II) in the range from 5.00 to 30.00 mg/L. Linear equation is y=0.0134x+0.0033 (R(2)=0.9948). Precision, assessed in the term of the relative standard deviation, RSD, and accuracy for multiple determinations obtained in values of 0.77-1.73% and 97.4%, respectively. The level of an average amount of Ni(II) in six piercing rings was evaluated to be 14.78 mg/g.

  9. Impact of sorption phenomena on multiphase conveying processes

    NASA Astrophysics Data System (ADS)

    Hatesuer, Florian; Groth, Tillmann; Reichwage, Mark; Mewes, Dieter; Luke, Andrea

    2011-08-01

    Twin-screw multiphase pumps are employed increasingly to convey multiphase mixtures of crude oil, accompanying fluids, associated gas and solid particles. They are positive displacement pumps and suitable for handling products containing liquid accompanied by large amounts of gas. Experimental investigations on the conveying characteristic, namely measuring the delivered volume flow as a function of the pressure difference, provide results for selected mixtures. By means of the on hand work, the influence of sorption phenomena occurring due to pressure variations alongside the conveying process on the conveying characteristics of twin-screw pumps delivering mixtures of oil and gases is measured. The employed gases are air and carbon dioxide, which differ strongly in solubility in oil. All experiments are conducted in a closed loop test facility, where oil and gas volume flows are mixed before the inlet and separated after the outlet of the multiphase pump. In order to simulate the influence of the suction side pressure drop in the reservoir on the conveying characteristic, packed beds are employed as oil-filed model. Sorption processes inside of the oil-field model and within the multiphase pump affect the conveying behaviour significantly. The two-phase flow in the inlet and outlet pipe is visualised by means of a capacitance tomography system. Results show that the oil fraction of the total delivered volume flow is decreased due to desorption at the pump inlet. The gas fraction at the pump outlet is further decreased due to absorption. Experimental results are compared to calculated solubilities of the on-hand gases in oil and to the theoretically derived gas volume flow fraction expected at the multiphase pump.

  10. Influence of growth phase on bacterial deposition: interaction mechanisms in packed-bed column and radial stagnation point flow systems.

    PubMed

    Walker, Sharon L; Redman, Jeremy A; Elimelech, Menachem

    2005-09-01

    The influence of bacterial growth stage on cell deposition kinetics has been examined using a mutant of Escherichia coli K12. Two experimental techniques--a packed-bed column and a radial stagnation point flow (RSPF) system--were employed to determine bacterial deposition rates onto quartz surfaces over a wide range of solution ionic strengths. Stationary-phase cells were found to be more adhesive than mid-exponential phase cells in both experimental systems. The divergence in deposition behavior was notably more pronounced in the RSPF than in the packed-bed system. For instance, in the RSPF system, the deposition rate of the stationary-phase cells at 0.03 M ionic strength was 14 times greater than that of the mid-exponential cells. The divergence in the packed-bed system was most significant at 0.01 M, where the deposition rate for the stationary-phase cells was nearly 4 times greater than for the mid-exponential cells. To explain the observed adhesion behavior, the stationary and mid-exponential bacterial cells were characterized for their size, surface charge density, electrophoretic mobility, viability, and hydrophobicity. On the basis of this analysis, it is suggested that the stationary cells have a more heterogeneous distribution of charged functional groups on the bacterial surface than the mid-exponential cells, which results in higher deposition kinetics. Furthermore, because the RSPF system enumerates only bacterial cells retained in primary minima, whereas the packed column captures mostly cells deposited in secondary minima, the difference in the stationary and mid-exponential cell deposition kinetics is much more pronounced in the RSPF system.

  11. Multiphase fluid simulation tools for winning remediation solutions

    SciTech Connect

    Deschaine, L.M.

    1997-07-01

    Releases of petroleum product such as gasoline and diesel fuels from normal operating practices to aquifers are common. The costs to remediate these releases can run in the billions of dollars. Solutions to remediate these releases usually consist of some form of multiphase (air, water, oil) fluid movement, whether it be a multiphase high vacuum extraction system, bioslurping, groundwater pump and treat system, an air sparging system, a soil vapor extraction system, a free product recovery system, bioremediation or the like. The software being tested in Test Drive, Multiphase Organic Vacuum Enhanced Recovery Simulator (MOVER) is a computer simulation tool that will give the practitioner the ability to design high vacuum enhanced multiple phase recovery systems and bioslurping systems, which are often the low cost effective remediation approach. It will also allow for the comparison of various proposed remediation approaches and technologies so the best solution can be chosen for a site. This is a key competitive advantage to translate conceptual ideas into winning bids.

  12. Relative importance of column and adsorption parameters on the productivity in preparative liquid chromatography II: Investigation of separation systems with competitive Langmuir adsorption isotherms.

    PubMed

    Forssén, Patrik; Samuelsson, Jörgen; Fornstedt, Torgny

    2014-06-20

    In this study we investigated how the maximum productivity for commonly used, realistic separation system with a competitive Langmuir adsorption isotherm is affected by changes in column length, packing particle size, mobile phase viscosity, maximum allowed column pressure, column efficiency, sample concentration/solubility, selectivity, monolayer saturation capacity and retention factor of the first eluting compound. The study was performed by generating 1000 random separation systems whose optimal injection volume was determined, i.e., the injection volume that gives the largest achievable productivity. The relative changes in largest achievable productivity when one of the parameters above changes was then studied for each system and the productivity changes for all systems were presented as distributions. We found that it is almost always beneficial to use shorter columns with high pressure drops over the column and that the selectivity should be greater than 2. However, the sample concentration and column efficiency have very limited effect on the maximum productivity. The effect of packing particle size depends on the flow rate limiting factor. If the pumps maximum flow rate is the limiting factor use smaller packing, but if the pressure of the system is the limiting factor use larger packing up to about 40μm.

  13. Modeling of intensity-modulated continuous-wave laser absorption spectrometer systems for atmospheric CO(2) column measurements.

    PubMed

    Lin, Bing; Ismail, Syed; Wallace Harrison, F; Browell, Edward V; Nehrir, Amin R; Dobler, Jeremy; Moore, Berrien; Refaat, Tamer; Kooi, Susan A

    2013-10-10

    The focus of this study is to model and validate the performance of intensity-modulated continuous-wave (IM-CW) CO(2) laser absorption spectrometer (LAS) systems and their CO(2) column measurements from airborne and satellite platforms. The model accounts for all fundamental physics of the instruments and their related CO(2) measurement environments, and the modeling results are presented statistically from simulation ensembles that include noise sources and uncertainties related to the LAS instruments and the measurement environments. The characteristics of simulated LAS systems are based on existing technologies and their implementation in existing systems. The modeled instruments are specifically assumed to be IM-CW LAS systems such as the Exelis' airborne multifunctional fiber laser lidar (MFLL) operating in the 1.57 μm CO(2) absorption band. Atmospheric effects due to variations in CO(2), solar radiation, and thin clouds, are also included in the model. Model results are shown to agree well with LAS atmospheric CO(2) measurement performance. For example, the relative bias errors of both MFLL simulated and measured CO(2) differential optical depths were found to agree to within a few tenths of a percent when compared to the in situ observations from the flight of 3 August 2011 over Railroad Valley (RRV), Nevada, during the summer 2011 flight campaign. In addition, the horizontal variations in the model CO(2) differential optical depths were also found to be consistent with those from MFLL measurements. In general, the modeled and measured signal-to-noise ratios (SNRs) of the CO(2) column differential optical depths (τd) agreed to within about 30%. Model simulations of a spaceborne IM-CW LAS system in a 390 km dawn/dusk orbit for CO(2) column measurements showed that with a total of 42 W of transmitted power for one offline and two different sideline channels (placed at different locations on the side of the CO(2) absorption line), the accuracy of the

  14. Assessing the suitability of sediment-type bioelectrochemical systems for organic matter removal from municipal wastewater: a column study.

    PubMed

    Khalfbadam, Hassan Mohammadi; Cheng, Ka Yu; Sarukkalige, Ranjan; Kayaalp, Ahmet S; Ginige, Maneesha P

    This study examines the use of bioelectrochemical systems (BES) as an alternative to rock filters for polishing wastewater stabilisation ponds (WSPs) effluent, which often contains soluble chemical oxygen demand (SCOD) and suspended solids mainly as algal biomass. A filter type sediment BES configuration with graphite granules (as the surrogate for rocks in a rock filter) was examined. Three reactor columns were set up to examine three different treatments: (i) open-circuit without current generation; (ii) close-circuit - with current generation; and (iii) control reactor without electrode material. All columns were continuously operated for 170 days with real municipal wastewater at a hydraulic retention time of 5 days. Compared to the control reactor, the two experimental reactors showed significant improvement of SCOD removal (from approximately 25% to 66%) possibly due to retention of biomass on the graphite media. However, substantial amount of SCOD (60%) was removed via non-current generation pathways, and a very low Coulombic efficiency (6%) was recorded due to a poor cathodic oxygen reduction kinetics and a large electrode spacing. Addressing these challenges are imperative to further develop BES technology for WSP effluent treatment.

  15. Multi-phase back contacts for CIS solar cells

    DOEpatents

    Rockett, Angus A.; Yang, Li-Chung

    1995-01-01

    Multi-phase, single layer, non-interdiffusing M-Mo back contact metallized films, where M is selected from Cu, Ga, or mixtures thereof, for CIS cells are deposited by a sputtering process on suitable substrates, preferably glass or alumina, to prevent delamination of the CIS from the back contact layer. Typical CIS compositions include CuXSe.sub.2 where X is In or/and Ga. The multi-phase mixture is deposited on the substrate in a manner to provide a columnar microstructure, with micro-vein Cu or/and Ga regions which partially or fully vertically penetrate the entire back contact layer. The CIS semiconductor layer is then deposited by hybrid sputtering and evaporation process. The Cu/Ga-Mo deposition is controlled to produce the single layer two-phase columnar morphology with controllable Cu or Ga vein size less than about 0.01 microns in width. During the subsequent deposition of the CIS layer, the columnar Cu/Ga regions within the molybdenum of the Cu/Ga-Mo back layer tend to partially leach out, and are replaced by columns of CIS. Narrower Cu and/or Ga regions, and those with fewer inner connections between regions, leach out more slowly during the subsequent CIS deposition. This gives a good mechanical and electrical interlock of the CIS layer into the Cu/Ga-Mo back layer. Solar cells employing In-rich CIS semiconductors bonded to the multi-phase columnar microstructure back layer of this invention exhibit vastly improved photo-electrical conversion on the order of 17% greater than Mo alone, improved uniformity of output across the face of the cell, and greater Fill Factor.

  16. Multi-phase back contacts for CIS solar cells

    DOEpatents

    Rockett, A.A.; Yang, L.C.

    1995-12-19

    Multi-phase, single layer, non-interdiffusing M-Mo back contact metallized films, where M is selected from Cu, Ga, or mixtures thereof, for CIS cells are deposited by a sputtering process on suitable substrates, preferably glass or alumina, to prevent delamination of the CIS from the back contact layer. Typical CIS compositions include CuXSe{sub 2} where X is In or/and Ga. The multi-phase mixture is deposited on the substrate in a manner to provide a columnar microstructure, with micro-vein Cu or/and Ga regions which partially or fully vertically penetrate the entire back contact layer. The CIS semiconductor layer is then deposited by hybrid sputtering and evaporation process. The Cu/Ga-Mo deposition is controlled to produce the single layer two-phase columnar morphology with controllable Cu or Ga vein size less than about 0.01 microns in width. During the subsequent deposition of the CIS layer, the columnar Cu/Ga regions within the molybdenum of the Cu/Ga-Mo back layer tend to partially leach out, and are replaced by columns of CIS. Narrower Cu and/or Ga regions, and those with fewer inner connections between regions, leach out more slowly during the subsequent CIS deposition. This gives a good mechanical and electrical interlock of the CIS layer into the Cu/Ga-Mo back layer. Solar cells employing In-rich CIS semiconductors bonded to the multi-phase columnar microstructure back layer of this invention exhibit vastly improved photo-electrical conversion on the order of 17% greater than Mo alone, improved uniformity of output across the face of the cell, and greater Fill Factor. 15 figs.

  17. Reactive multiphase flow simulation workshop summary

    SciTech Connect

    VanderHeyden, W.B.

    1995-09-01

    A workshop on computer simulation of reactive multiphase flow was held on May 18 and 19, 1995 in the Computational Testbed for Industry at Los Alamos National Laboratory (LANL), Los Alamos, New Mexico. Approximately 35 to 40 people attended the workshop. This included 21 participants from 12 companies representing the petroleum, chemical, environmental and consumer products industries, two representatives from the DOE Office of Industrial Technologies and several from Los Alamos. The dialog at the meeting suggested that reactive multiphase flow simulation represents an excellent candidate for government/industry/academia collaborative research. A white paper on a potential consortium for reactive multiphase flow with input from workshop participants will be issued separately.

  18. Multiphase Flow Analysis in Hydra-TH

    SciTech Connect

    Christon, Mark A.; Bakosi, Jozsef; Francois, Marianne M.; Lowrie, Robert B.; Nourgaliev, Robert

    2012-06-20

    This talk presents an overview of the multiphase flow efforts with Hydra-TH. The presentation begins with a definition of the requirements and design principles for multiphase flow relevant to CASL-centric problems. A brief survey of existing codes and their solution algorithms is presented before turning the model formulation selected for Hydra-TH. The issues of hyperbolicity and wellposedness are outlined, and a three candidate solution algorithms are discussed. The development status of Hydra-TH for multiphase flow is then presented with a brief summary and discussion of future directions for this work.

  19. Multiphase groundwater flow near cooling plutons

    USGS Publications Warehouse

    Hayba, D.O.; Ingebritsen, S.E.

    1997-01-01

    We investigate groundwater flow near cooling plutons with a computer program that can model multiphase flow, temperatures up to 1200??C, thermal pressurization, and temperature-dependent rock properties. A series of experiments examines the effects of host-rock permeability, size and depth of pluton emplacement, single versus multiple intrusions, the influence of a caprock, and the impact of topographically driven groundwater flow. We also reproduce and evaluate some of the pioneering numerical experiments on flow around plutons. Host-rock permeability is the principal factor influencing fluid circulation and heat transfer in hydrothermal systems. The hottest and most steam-rich systems develop where permeability is of the order of 10-15 m2. Temperatures and life spans of systems decrease with increasing permeability. Conduction-dominated systems, in which permeabilities are ???10-16m2, persist longer but exhibit relatively modest increases in near-surface temperatures relative to ambient conditions. Pluton size, emplacement depth, and initial thermal conditions have less influence on hydrothermal circulation patterns but affect the extent of boiling and duration of hydrothermal systems. Topographically driven groundwater flow can significantly alter hydrothermal circulation; however, a low-permeability caprock effectively decouples the topographically and density-driven systems and stabilizes the mixing interface between them thereby defining a likely ore-forming environment.

  20. Multiphase Modeling of Water Injection on Flame Deflector

    NASA Technical Reports Server (NTRS)

    Vu, Bruce T.; Bachchan, Nili; Peroomian, Oshin; Akdag, Vedat

    2013-01-01

    This paper describes the use of an Eulerian Dispersed Phase (EDP) model to simulate the water injected from the flame deflector and its interaction with supersonic rocket exhaust from a proposed Space Launch System (SLS) vehicle. The Eulerian formulation, as part of the multi-phase framework, is described. The simulations show that water cooling is only effective over the region under the liquid engines. Likewise, the water injection provides only minor effects over the surface area under the solid engines.

  1. Multi-Phase Modeling of Rainbird Water Injection

    NASA Technical Reports Server (NTRS)

    Vu, Bruce T.; Moss, Nicholas; Sampson, Zoe

    2014-01-01

    This paper describes the use of a Volume of Fluid (VOF) multiphase model to simulate the water injected from a rainbird nozzle used in the sound suppression system during launch. The simulations help determine the projectile motion for different water flow rates employed at the pad, as it is critical to know if water will splash on the first-stage rocket engine during liftoff.

  2. Blind Geothermal System Exploration in Active Volcanic Environments; Multi-phase Geophysical and Geochemical Surveys in Overt and Subtle Volcanic Systems, Hawai’i and Maui

    SciTech Connect

    Fercho, Steven; Owens, Lara; Walsh, Patrick; Drakos, Peter; Martini, Brigette; Lewicki, Jennifer L.; Kennedy, Burton M.

    2015-08-01

    Suites of new geophysical and geochemical exploration surveys were conducted to provide evidence for geothermal resource at the Haleakala Southwest Rift Zone (HSWRZ) on Maui Island, Hawai’i. Ground-based gravity (~400 stations) coupled with heli-bourne magnetics (~1500 line kilometers) define both deep and shallow fractures/faults, while also delineating potentially widespread subsurface hydrothermal alteration on the lower flanks (below approximately 1800 feet a.s.l.). Multi-level, upward continuation calculations and 2-D gravity and magnetic modeling provide information on source depths, but lack of lithologic information leaves ambiguity in the estimates. Additionally, several well-defined gravity lows (possibly vent zones) lie coincident with magnetic highs suggesting the presence of dike intrusions at depth which may represent a potentially young source of heat. Soil CO2 fluxes were measured along transects across geophysically-defined faults and fractures as well as young cinder cones along the HSWRZ. This survey generally did not detect CO2 levels above background, with the exception of a weak anomalous flux signal over one young cinder cone. The general lack of observed CO2 flux signals on the HSWRZ is likely due to a combination of lower magmatic CO2 fluxes and relatively high biogenic surface CO2 fluxes which mix with the magmatic signal. Similar surveys at the Puna geothermal field on the Kilauea Lower East Rift Zone (KLERZ) also showed a lack of surface CO2 flux signals, however aqueous geochemistry indicated contribution of magmatic CO2 and He to shallow groundwater here. As magma has been intercepted in geothermal drilling at the Puna field, the lack of measured surface CO2 flux indicative of upflow of magmatic fluids here is likely due to effective “scrubbing” by high groundwater and a mature hydrothermal system. Dissolved inorganic carbon (DIC) concentrations, δ13C compositions and 3He/4He values were sampled at Maui from several shallow

  3. Shock Driven Multiphase Instabilities in Scramjet Applications

    NASA Astrophysics Data System (ADS)

    McFarland, Jacob

    2016-11-01

    Shock driven multiphase instabilities (SDMI) arise in many applications from dust production in supernovae to ejecta distribution in explosions. At the limit of small, fast reacting particles the instability evolves similar to the Richtmyer-Meshkov (RM) instability. However, as additional particle effects such as lag, phase change, and collisions become significant the required parameter space becomes much larger and the instability deviates significantly from the RM instability. In scramjet engines the SDMI arises during a cold start where liquid fuel droplets are injected and processed by shock and expansion waves. In this case the particle evaporation and mixing is important to starting and sustaining combustion, but the particles are large and slow to react, creating significant multiphase effects. This talk will examine multiphase mixing in scramjet relevant conditions in 3D multiphase hydrodynamic simulations using the FLASH code from the University of Chicago FLASH center.

  4. Continuous countercurrent membrane column for the separation of solute/solvent and solvent/solvent systems

    DOEpatents

    Nerad, Bruce A.; Krantz, William B.

    1988-01-01

    A reverse osmosis membrane process or hybrid membrane - complementary separator process for producing enriched product or waste streams from concentrated and dilute feed streams for both solvent/solvent and solute/solvent systems is described.

  5. RF characteristics of the hoop column antenna for the land mobile satellite system mission

    NASA Technical Reports Server (NTRS)

    Foldes, P.

    1984-01-01

    A communication system using a satellite with a 118 meter diameter quad aperture antenna to provide telephone service to mobile users remotely located from the large metropolitan areas where the telephone companies are presently implementing their cellular system is described. In this system, which is compatible with the cellular system, the mobile user communicates with the satellite at UHF frequencies. The satellite connects him at S-Band, to the existing telephone network via a base station. The results of the RF definition work for the quad aperture antenna are presented. The elements of the study requirements for the LMSS are summarized, followed by a beam topology plan which satisfies the mission requirements with a practical and realiable configuration. The geometry of the UHF antenna and its radiation characteristics are defined. The various feed alternatives, and the S-band aperture are described.

  6. RF characteristics of the hoop column antenna for the land mobile satellite system mission

    NASA Astrophysics Data System (ADS)

    Foldes, P.

    1984-11-01

    A communication system using a satellite with a 118 meter diameter quad aperture antenna to provide telephone service to mobile users remotely located from the large metropolitan areas where the telephone companies are presently implementing their cellular system is described. In this system, which is compatible with the cellular system, the mobile user communicates with the satellite at UHF frequencies. The satellite connects him at S-Band, to the existing telephone network via a base station. The results of the RF definition work for the quad aperture antenna are presented. The elements of the study requirements for the LMSS are summarized, followed by a beam topology plan which satisfies the mission requirements with a practical and realiable configuration. The geometry of the UHF antenna and its radiation characteristics are defined. The various feed alternatives, and the S-band aperture are described.

  7. A novel ion chromatography cycling-column-switching system for the determination of low-level chlorate and nitrite in high salt matrices.

    PubMed

    Wang, Nani; Wang, Rui Qi; Zhu, Yan

    2012-10-15

    A novel ion chromatography cycling-column-switching system was developed for the determination of chlorate and nitrite in high salt matrices. The simple system included a pump, two valves, a single eluent, and a conductivity detector. Both online pre-concentration and matrix elimination were achieved by this method. The target anions were eluted from the concentrator column to the analytical columns circularly. Chloride matrix was then eliminated completely. The method was applied to the determination of low-level chlorate and nitrite in the chloride matrix. Our experimental results demonstrated that this system is of advantages such as high sensitivity, facile automation and simple sample pretreatment, which might be a promising approach for environmental researches and food control.

  8. Development of a passive doas system to retrieve atmospheric pollution columns in the 200 to 355 nm region

    PubMed Central

    2013-01-01

    In recent years several techniques have been developed to measure and monitor the pollution of the air. Among these techniques, remote sensing using optical methods stands out due to several advantages for air quality control applications. A Passive Differential Optical Absorption Spectroscopy system that uses the ultraviolet region from 200 to 355 nm of the solar radiation is presented. The developed system is portable; therefore it is practical for real time and in situ measurements. The enhanced wavelength range of the system is intended to detect the ultraviolet light penetration in the Mexican Valley considering the solar zenith angle and the altitude. The system was applied to retrieve atmospheric SO2 columns emitted either by anthropogenic (power plant) or natural sources (volcano), reaching a detection limit of about 1 ppm. The measurement of the penetrating solar radiation on the earth surface at the UVC range is presented and the possibility to measure pollution traces of some contaminants as O3, NO2 and aromatic compounds in real time and in situ in the ultraviolet region is discussed. PMID:23369629

  9. Development of a passive doas system to retrieve atmospheric pollution columns in the 200 to 355 nm region.

    PubMed

    Mejía, Rubén Galicia; Vázquez, Josémanueldelarosa; Isakina, Suren Stolik; García, Edgard Moreno; Iglesias, Gustavo Sosa

    2013-01-08

    In recent years several techniques have been developed to measure and monitor the pollution of the air. Among these techniques, remote sensing using optical methods stands out due to several advantages for air quality control applications. A Passive Differential Optical Absorption Spectroscopy system that uses the ultraviolet region from 200 to 355 nm of the solar radiation is presented. The developed system is portable; therefore it is practical for real time and in situ measurements. The enhanced wavelength range of the system is intended to detect the ultraviolet light penetration in the Mexican Valley considering the solar zenith angle and the altitude. The system was applied to retrieve atmospheric SO2 columns emitted either by anthropogenic (power plant) or natural sources (volcano), reaching a detection limit of about 1 ppm. The measurement of the penetrating solar radiation on the earth surface at the UVC range is presented and the possibility to measure pollution traces of some contaminants as O3, NO2 and aromatic compounds in real time and in situ in the ultraviolet region is discussed.

  10. Analysis of cytokine profile and growth factors in platelet-rich plasma obtained by open systems and commercial columns

    PubMed Central

    Pochini, Alberto de Castro; Antonioli, Eliane; Bucci, Daniella Zanetti; Sardinha, Luiz Roberto; Andreoli, Carlos Vicente; Ferretti, Mario; Ejnisman, Benno; Goldberg, Anna Carla; Cohen, Moisés

    2016-01-01

    ABSTRACT Objective: To evaluate growth factors and cytokines in samples of platelet-rich plasma obtained by three different centrifugation methods. Methods: Peripheral blood of six individuals with no hematological diseases, aged 18 to 68 years, was drawn to obtain platelet-rich plasma, using the open method and commercial columns by Medtronic and Biomet. The products obtained with the different types of centrifugation were submitted to laboratory analysis, including pro-inflammatory cytokines and chemokines by flow cytometry assays, the concentration of fibroblast growth factors-2 (FGF-2) and transforming growth factor-beta1 (TGF-β1). Results: The diverse separation methods generated systematically different profiles regarding number of platelets and leukocytes. The Medtronic system yielded a product with the highest concentration of platelets, and the open method, with the lowest concentration of platelets. The results of cytokine analysis showed that the different types of centrifugation yielded products with high concentrations of interleukin 8, interleukin 1β. The open system resulted in a product with high levels of interleukin 6. Other cytokines and chemokines measured were similar between systems. The product obtained with the open method showed higher levels of TGF-β1 in relation to other systems and low FGF-2 levels. Conclusion: The formed elements, growth factors and cytokines in samples of platelet-rich plasma varied according to the centrifugation technique used. PMID:27759829

  11. Comparison of Frameworks for Next Generation Multiphase Flow Solver, MFIX: A Group Decision-Making Exercise

    SciTech Connect

    Gel, Aytekin; Pannala, Sreekanth; Syamlal, M; O'Brien, T. J.; Gel, Esma

    2007-01-01

    Computational Fluid Dynamics (CFD) simulations have emerged as a powerful tool for understanding multiphase flows that occur in a wide range of engineering applications and natural processes. A multiphase CFD code called MFIX has been under development at the National Energy Technology Laboratory (NETL) since the 1980s for modeling multiphase flows that occur in fossil fuel reactors. CFD codes such as MFIX are equipped with a number of numerical algorithms to solve a large set of coupled partial differential equations over three-dimensional grids consisting of hundreds of thousands of cells on parallel computers. Currently, the next generation version of MFIX is under development with the goal of building a multiphase problem solving environment (PSE) that would facilitate the simple reuse of modern software components by application scientists. Several open-source frameworks were evaluated to identify the best-suited framework for the multiphase PSE. There are many requirements for the multiphase PSE, and each of these open-source frameworks offers functionalities that satisfy the requirements to varying extents. Therefore, matching the requirements and the functionalities is not a simple task and requires a systematic and quantitative decision making procedure. We present a multi-criteria decision making approach to determining a major system design decision, and demonstrate its application on the framework selection problem.

  12. All-aqueous multiphase microfluidics

    PubMed Central

    Song, Yang; Sauret, Alban; Cheung Shum, Ho

    2013-01-01

    Immiscible aqueous phases, formed by dissolving incompatible solutes in water, have been used in green chemical synthesis, molecular extraction and mimicking of cellular cytoplasm. Recently, a microfluidic approach has been introduced to generate all-aqueous emulsions and jets based on these immiscible aqueous phases; due to their biocompatibility, these all-aqueous structures have shown great promises as templates for fabricating biomaterials. The physico-chemical nature of interfaces between two immiscible aqueous phases leads to unique interfacial properties, such as an ultra-low interfacial tension. Strategies to manipulate components and direct their assembly at these interfaces needs to be explored. In this paper, we review progress on the topic over the past few years, with a focus on the fabrication and stabilization of all-aqueous structures in a multiphase microfluidic platform. We also discuss future efforts needed from the perspectives of fluidic physics, materials engineering, and biology for fulfilling potential applications ranging from materials fabrication to biomedical engineering. PMID:24454609

  13. Measurement in multiphase reacting flows

    NASA Technical Reports Server (NTRS)

    Chigier, N. A.

    1979-01-01

    A survey is presented of diagnostic techniques and measurements made in multiphase reacting flows. The special problems encountered by the presence of liquid droplets, soot and solid particles in high temperature chemically reacting turbulent environments are outlined. The principal measurement techniques that have been tested in spray flames are spark photography, laser anemometry, thermocouples and suction probes. Spark photography provides measurement of drop size, drop size distribution, drop velocity, and angle of flight. Photographs are analysed automatically by image analysers. Photographic techniques are reliable, inexpensive and proved. Laser anemometers have been developed for simultaneous measurement of velocity and size of individual particles in sprays under conditions of vaporization and combustion. Particle/gas velocity differentials, particle Reynolds numbers, local drag coefficients and direct measurement of vaporization rates can be made by laser anemometry. Gas temperature in sprays is determined by direct in situ measurement of time constants immediately prior to measurement with compensation and signal analysis by micro-processors. Gas concentration is measured by suction probes and gas phase chromatography. Measurements of particle size, particle velocity, gas temperature, and gas concentration made in airblast and pressure atomised liquid spray flames are presented.

  14. The effect of high column density systems on the measurement of the Lyman-α forest correlation function

    SciTech Connect

    Font-Ribera, Andreu; Miralda-Escudé, Jordi E-mail: miralda@icc.ub.edu

    2012-07-01

    We present a study of the effect of High Column Density (HCD) systems on the Lyα forest correlation function on large scales. We study the effect both numerically, by inserting HCD systems on mock spectra for a specific model, and analytically, in the context of two-point correlations and linear theory. We show that the presence of HCDs substantially contributes to the noise of the correlation function measurement, and systematically alters the measured redshift-space correlation function of the Lyα forest, increasing the value of the density bias factor and decreasing the redshift distortion parameter β{sub α} of the Lyα forest. We provide simple formulae for corrections on these derived parameters, as a function of the mean effective optical depth and bias factor of the host halos of the HCDs, and discuss the conditions under which these expressions should be valid. In practice, precise corrections to the measured parameters of the Lyα forest correlation for the HCD effects are more complex than the simple analytical approximations we present, owing to non-linear effects of the damped wings of the HCD systems and the presence of three-point terms. However, we conclude that an accurate correction for these HCD effects can be obtained numerically and calibrated with observations of the HCD-Lyα cross-correlation. We also discuss an analogous formalism to treat and correct for the contaminating effect of metal lines overlapping the Lyα forest spectra.

  15. Modelling of fluid-structure interaction with multiphase viscous flows using an immersed-body method

    NASA Astrophysics Data System (ADS)

    Yang, P.; Xiang, J.; Fang, F.; Pavlidis, D.; Latham, J.-P.; Pain, C. C.

    2016-09-01

    An immersed-body method is developed here to model fluid-structure interaction for multiphase viscous flows. It does this by coupling a finite element multiphase fluid model and a combined finite-discrete element solid model. A coupling term containing the fluid stresses is introduced within a thin shell mesh surrounding the solid surface. The thin shell mesh acts as a numerical delta function in order to help apply the solid-fluid boundary conditions. When used with an advanced interface capturing method, the immersed-body method has the capability to solve problems with fluid-solid interfaces in the presence of multiphase fluid-fluid interfaces. Importantly, the solid-fluid coupling terms are treated implicitly to enable larger time steps to be used. This two-way coupling method has been validated by three numerical test cases: a free falling cylinder in a fluid at rest, elastic membrane and a collapsing column of water moving an initially stationary solid square. A fourth simulation example is of a water-air interface with a floating solid square being moved around by complex hydrodynamic flows including wave breaking. The results show that the immersed-body method is an effective approach for two-way solid-fluid coupling in multiphase viscous flows.

  16. [Investigation of a gas chromatographic column system for the on-line analysis of gaseous components in de-propane tower of pyrolysis equipment].

    PubMed

    Cai, H; Liu, L J; Yan, J; Lu, X; Ye, F; Xu, G W

    2000-03-01

    Multi-dimensional gas chromatograph has become an important process analyzer due to the advantages of high resolution and fast speed. According to the production requirement, a gas chromatographic column switching system has been investigated for the on-line analysis of gaseous components from high-pressure and lower-pressure de-propane towers of pyrolysis equipment. By using two different injection times on three injectors, and fore-flush and back-flush techniques, C2-hydrocarbons, propane, propene, methylacetylene, propadiene and C4-hydrocarbons can be separated on 7 columns in 7 minutes. The practical application showed the developed column system is suitable for the on-line monitoring of the production process.

  17. In situ imaging of multiphase bio-interfaces at the micro-/nanoscale.

    PubMed

    Chen, Peipei; Jiang, Lei; Han, Dong

    2011-10-17

    The multiphase bio-interfacial system constituted by biological surfaces and their surrounding environment is usually considered to be an essential clue for exploring the mysterious relationship between surface architecture and function. As a visualizing method to understand these systems, in situ imaging of multiphase interfaces (e.g., air/liquid/solid and oil/water/solid systems) at the micro-/nanoscale, still remains a huge challenge, as a result of their heterogeneity and complexity. Here, recent progress on real-space micro-/nanoscale imaging of multiphase bio-interfacial systems is reviewed; this includes several techniques and imaging results on bio-interfaces, such as the lotus leaf, fish scale, living cell's surface, and fresh tissue surface. The results evidently show that interfacial structures have a significant impact on the state of the microscopic multiphase interface, further influencing specific functions. Based on this research, technical innovations, some more complicated multiphase interface systems, and structure-function coupling mechanism are proposed.

  18. Shock driven multiphase flow with particle evaporation

    NASA Astrophysics Data System (ADS)

    Dahal, Jeevan; McFarland, Jacob

    2016-11-01

    The computational study of the shock driven instability of a multiphase system with particle evaporation is presented. The particle evaporation modifies the evolution of the interface due to the addition of the vapor phase to the gas. The effects can be quantitatively measured by studying various gas parameters like density, temperature, vorticity and particle properties like diameter and temperature. In addition, the size distribution of particles also modifies the development of instability as the larger size particles damp the evolution of interface in comparison to the smaller size particles. The simulation results are presented to study these effects using FLASH developed at the FLASH Center at the University of Chicago. The capabilities of FLASH for particle modeling were extended using the Particle in Cell (PIC) technique for coupling of mass, momentum, and energy between the particle and carrier gas. A seeded cylinder of gas with particles having either a single radius or a distribution of radii was studied. The enstrophy production and destruction mechanisms were explored to understand the reason for change in vorticity with particle size.

  19. Multiphase modelling of mud volcanoes

    NASA Astrophysics Data System (ADS)

    Colucci, Simone; de'Michieli Vitturi, Mattia; Clarke, Amanda B.

    2015-04-01

    Mud volcanism is a worldwide phenomenon, classically considered as the surface expression of piercement structures rooted in deep-seated over-pressured sediments in compressional tectonic settings. The release of fluids at mud volcanoes during repeated explosive episodes has been documented at numerous sites and the outflows resemble the eruption of basaltic magma. As magma, the material erupted from a mud volcano becomes more fluid and degasses while rising and decompressing. The release of those gases from mud volcanism is estimated to be a significant contributor both to fluid flux from the lithosphere to the hydrosphere, and to the atmospheric budget of some greenhouse gases, particularly methane. For these reasons, we simulated the fluid dynamics of mud volcanoes using a newly-developed compressible multiphase and multidimensional transient solver in the OpenFOAM framework, taking into account the multicomponent nature (CH4, CO2, H2O) of the fluid mixture, the gas exsolution during the ascent and the associated changes in the constitutive properties of the phases. The numerical model has been tested with conditions representative of the LUSI, a mud volcano that has been erupting since May 2006 in the densely populated Sidoarjo regency (East Java, Indonesia), forcing the evacuation of 40,000 people and destroying industry, farmland, and over 10,000 homes. The activity of LUSI mud volcano has been well documented (Vanderkluysen et al., 2014) and here we present a comparison of observed gas fluxes and mud extrusion rates with the outcomes of numerical simulations. Vanderkluysen, L.; Burton, M. R.; Clarke, A. B.; Hartnett, H. E. & Smekens, J.-F. Composition and flux of explosive gas release at LUSI mud volcano (East Java, Indonesia) Geochem. Geophys. Geosyst., Wiley-Blackwell, 2014, 15, 2932-2946

  20. EOS7Cm: An improved TOUGH2 module for simulating non-isothermal multiphase and multicomponent flow in CO2-H2S-CH4-brine systems with high pressure, temperature and salinity

    NASA Astrophysics Data System (ADS)

    Lei, Hongwu; Li, Jun; Li, Xiaochun; Jiang, Zhenjiao

    2016-09-01

    Understanding the non-isothermal multiphase and multicomponent flow in a CO2-H2S-CH4-brine system is of critical importance in projects such as CO2 storage in deep saline aquifers, natural gas extraction using CO2 as the displacement fluid, and heat extraction from hot dry rocks using CO2 as the working fluid. Numerical simulation is a necessary tool to evaluate the chemical evolution in these systems. However, an accurate thermodynamic model for CO2-H2S-CH4-brine systems appropriate for high pressure, temperature, and salinity is still lacking. This study establishes the mutual solubility model for CO2-H2S-CH4-brine systems based on the fugacity-activity method for phase equilibrium. The model can predict mutual solubilities for pressure up to 1000 bar for CO2 and CH4, and 200 bar for H2S, for temperature up to 200 °C, and for salinity up to 6 mol/kg water. We incorporated the new model into TOUGH2/EOS7C, forming a new improved module we call EOS7Cm. Compared to the original EOS7C, EOS7Cm considers the effects of H2S and covers a larger range of temperature and salinity. EOS7Cm is employed in five examples, including CO2 injection with and without impurities (CH4 and/or H2S) into deep aquifers, CH4 extraction from aquifers by CO2 injection, and heat extraction from hot dry rock. The results are compared to those from TOUGH2/ECO2N, EOS7C and CMG, agreement among which serves to verify EOS7Cm.

  1. Multi-speed multi-phase resolver converter

    NASA Technical Reports Server (NTRS)

    Alhorn, Dean C. (Inventor); Howard, David E. (Inventor)

    1995-01-01

    A multiphase converter circuit generates a plurality of sinusoidal outputs of displaced phase and given speed value from the output of an angular resolver system attachable to a motor excited by these multi-phase outputs, the resolver system having a lower speed value than that of the motor. The angular resolver system provides in parallel format sequential digital numbers indicative of the amount of rotation of the shaft of an angular position sensor associated with the angular resolver system. These numbers are used to excite simultaneously identical addresses of a plurality of addressable memory systems, each memory system having stored therein at sequential addresses sequential values of a sinusoidal wavetrain of a given number of sinusoids. The stored wavetrain values represent sinusoids displaced from each other in phase according to the number of output phases desired. A digital-to-analog converter associated with each memory system converts each accessed word to a corresponding analog value to generate attendant to rotation of the angular resolver a sinusoidal wave of proper phase at each of the plurality of outputs. By properly orienting the angular resolver system with respect to the rotor of the motor, essentially ripple-free torque is supplied to the rotor. The angular resolver system may employ an analog resolver feeding an integrated circuit resolver-to-digital converter to produce the requisite digital values serving as addresses. Alternative versions employing incremental or absolute encoders are also described.

  2. Lagrangian coherent structures analysis of gas-liquid flow in a bubble column

    NASA Astrophysics Data System (ADS)

    Wu, Qin; Wang, GuoYu; Huang, Biao; Bai, ZeYu

    2014-06-01

    The objective of this paper is to apply a new identifying method to investigating the gas-liquid two-phase flow behaviors in a bubble column with air injected into water. In the numerical simulations, the standard k- ɛ turbulence model is employed to describe the turbulence phenomenon occurring in the continuous fluid. The Finite-Time Lyapunov Exponent (FTLE) and Lagrangian Coherent Structures (LCS) are applied to analyze the vortex structures in multiphase flow. Reasonable agreements are obtained between the numerical and experimental data. The numerical results show that the evolution of gas-liquid in the column includes initial and periodical developing stages. During the initial stage, the bubble hose is forming and extending along the vertical direction with the vortex structures formed symmetrically. During the periodical developing stage, the bubble hose starts to oscillate periodically, and the vortexes move along the bubble hose to the bottom of column alternately. Compared to the Euler-system-based identification criterion of a vortex, the FTLE field presents the boundary of a vortex without any threshold defined and the LCS represents the divergence extent of infinite neighboring particles. During the initial stage, the interfaces between the forward and backward flows are highlighted by the LCS. As for the periodical developing stage, the LCS curls near the vortex centers, providing a method of analyzing a flow field from a dynamical system perspective.

  3. Investigation on Online Multiphase Flow Meter in oilfield Based on Open Channel Flow

    NASA Astrophysics Data System (ADS)

    Meng, L. Y.; Wang, W. C.; Li, Y. X.; Zhang, J.; Dong, S. P.

    2010-03-01

    Flow metering of multiphase pipeline is an urgently problem needed to be solved in oilfield producing in China. Based on the principle of multiphase oil and gas flow in the open channel, four liquid metering models(Falling Model I, Falling Model II, Open Channel Model and Element Resistance Model) and one gas model were obtained to calculate the gas and liquid flow rate, in which the water cut was measured by the differential pressure. And then a new type of multiphase meter system was developed based on these models and neural networks were developed to improve the estimating results of gas and liquid flow rate with the new metering system. At last a lot of experiments of multiphase metering were finished in lab and field. According to the experiments, the results of the metering system show that the liquid flow rate error was no more than 10%, and gas flow rate error was no more than 15%, which can meet the demand of the field flow rate measurement. Furthermore the relationship between liquid and gas flow rate and characteristic signals was found out through the experiments so as to deepening the study on multiphase flow metering technology.

  4. The separation of flavonoids from Pongamia pinnata using combination columns in high-speed counter-current chromatography with a three-phase solvent system.

    PubMed

    Yin, Hao; Zhang, Si; Long, Lijuan; Yin, Hang; Tian, Xinpeng; Luo, Xiongming; Nan, Haihan; He, Sha

    2013-11-08

    The mangrove plant Pongamia pinnata (Leguminosae) is well known as a plant pesticide. Previous studies have indicated that the flavonoids are responsible of the biological activities of the plant. A new high-speed counter-current chromatography (HSCCC) method for the separation of three flavonoids, karanjin (1), pinnatin (2), and pongaflavone (3), from P. pinnata was developed in the present study. The lower and intermediate phase (LP and IP) of a new three-phase solvent system, n-hexane-acetonitrile-dichloromethane-water, at a volume ratio of 5:5:1:5, were used as the stationary phases, while the upper phase (UP) was used as the mobile phase, and the volume ratio between the stationary phases in the CCC column could be tuned by varying the initial pumped volume ratio of the stationary phases. The CCC columns containing all three phases of the solvent system were considered combination columns. According to the theories of combination column, it is possible to optimize the retention time of the target compounds by varying the volume ratio of the stationary phases in the HSCCC combination columns, as well as the suitable volume ratios of the stationary phases for the separation of the target compounds were predicted from the partition coefficients of the compounds in the three-phase solvent system. Then, three HSCCC separations using the combination columns with initial pumped LP:IP volume ratios of 1:0, 0.9:0.1, and 0.7:0.3 were performed separately based on the prediction. Three target compounds were prepared with high purity when the initial pumped volume ratio of the stationary phases was 0.9:0.1. The baseline separation of compounds 2 and 3 was achieved on the combination column with an initial pumped volume ratio of 0.7:0.3. Furthermore, the three experiments clearly demonstrated that the retentions and resolutions of the target compounds increased with an increasing volume ratio of IP, which is consistent with the prediction for the retention times for the

  5. Multiphase pumps make field wells more economic

    SciTech Connect

    Morrow, M.; Mabes, T.

    1995-11-01

    While proposed applications of multiphase (MP) pumps in subsea developments have generated much publicity, particularly in Europe, applications on a smaller scale in several remote and/or marginal well situations have been quietly improving producing operations. This short article describes one such application in Alberta, Canada, in which a simple, screw-type multiphase pump installation solved well flow problems for Imperial Oil Resources. Bornemann Pumps Inc., supplier for equipment for this application says more than 40 such pumps have been delivered for various field problem solutions in eight countries. Basic design and function of the rotary screw type MP pump used in these applications are overviewed below.

  6. Effect of an open tube in series with a packed capillary column on liquid chromatographic performance. The influence of particle diameter, temperature, and system pressure.

    PubMed

    Xu, Hongjuan; Weber, Stephen G

    2009-02-27

    A postcolumn reactor or a simple open tube connecting a capillary column to, for example, a mass spectrometer affects the performance of a capillary liquid chromatography system in two ways: stealing pressure from the column and adding band-spreading. This effect is especially intolerable in fast separations. Our calculations show that in the presence of a 25 microm radius postcolumn reactor, column (50 microm radius) efficiency (number of theoretical plates) is severely reduced by more than 75% with a t(0) of 10s and a particle diameter from 1 to 5 microm for unretained solutes at room temperature. Therefore, it is necessary to minimize the reactor's effect and to improve the column efficiency by optimizing postcolumn conditions. We derived an equation that defines the observed number of theoretical plates (N(obs)) taking into account the two effects stated above, which is a function of the maximum pressure P(m), the particle diameter d(p), the reactor radius a(r), the column radius a(c), the desired dead time t(0), the column temperature T and zone capacity factor k''. Poppe plots were obtained by calculations using this equation. The results show that for a t(0) shorter than 18s, a P(m) of 4000 psi, and a d(p) of 1.7 microm, a 5 microm radius reactor has to be used. Such a small reactor is difficult to fabricate. Fortunately, high temperature helps to minimize the reactor effect so that reactors with manageable radius (larger than 12.5 microm) can be used in many practical conditions. Furthermore, solute retention diminishes the influence of a postcolumn reactor. Thus, a 12.5 microm reactor supersedes a 5 microm reactor for retained solutes even at a t(0) of 5s (k''>3.8, or k'>2.0).

  7. Workshop on Scientific Issues in Multiphase Flow

    SciTech Connect

    Hanratty, Thomas J.

    2003-01-02

    This report outlines scientific issues whose resolution will help advance and define the field of multiphase flow. It presents the findings of four study groups and of a workshop sponsored by the Program on Engineering Physics of the Department of Energy. The reason why multiphase flows are much more difficult to analyze than single phase flows is that the phases assume a large number of complicated configurations. Therefore, it should not be surprising that the understanding of why the phases configure in a certain way is the principal scientific issue. Research is needed which identifies the microphysics controlling the organization of the phases, which develops physical models for the resultant multi-scale interactions and which tests their validity in integrative experiments/theories that look at the behavior of a system. New experimental techniques and recently developed direct numerical simulations will play important roles in this endeavor. In gas-liquid flows a top priority is to develop an understanding of why the liquid phase in quasi fully-developed pipe flow changes from one configuration to another. Mixing flows offer a more complicated situation in which several patterns can exist at the same time. They introduce new physical challenges. A second priority is to provide a quantitative description of the phase distribution for selected fully-developed flows and for simple mixing flows (that could include heat transfer and phase change). Microphysical problems of interest are identified – including the coupling of molecular and macroscopic behavior that can be observed in many situations and the formation/destruction of interfaces in the coalescence/breakup of drops and bubbles. Solid-fluid flows offer a simpler system in that interfaces are not changing. However, a variety of patterns exist, that depend on the properties of the particles, their concentration and the Reynolds number characterizing the relative velocity. A top priority is the

  8. Temperature programmable microfabricated gas chromatography column

    DOEpatents

    Manginell, Ronald P.; Frye-Mason, Gregory C.

    2003-12-23

    A temperature programmable microfabricated gas chromatography column enables more efficient chemical separation of chemical analytes in a gas mixture by the integration of a resistive heating element and temperature sensing on the microfabricated column. Additionally, means are provided to thermally isolate the heated column from their surroundings. The small heat capacity and thermal isolation of the microfabricated column improves the thermal time response and power consumption, both important factors for portable microanalytical systems.

  9. Sedimentation and multiphase equilibria in suspensions of colloidal hard rods.

    PubMed

    Savenko, S V; Dijkstra, Marjolein

    2004-11-01

    Sedimentation and multiphase equilibria in a suspension of hard colloidal rods are explored by analyzing the (macroscopic) osmotic equilibrium conditions. We observe that gravity enables the system to explore a whole range of phases varying from the most dilute phase to the densest phase, i.e., from the isotropic (I), to the nematic (N), to the smectic (Sm), to the crystal (K) phase. We determine the phase diagrams for hard spherocylinders with a length-to-diameter ratio of 5 for a semi-infinite system and a system with fixed container height using a bulk equation of state obtained from simulations. Our results show that gravity leads to multiphase coexistence for the semi-infinite system, as we observe I, I+N, I+N+Sm , or I+N+Sm+K coexistence, while the finite system shows I, N, Sm, K, I+N, N+Sm, Sm+K, I+N+Sm, N+Sm+K , and I+N+Sm+K phase coexistence. In addition, we compare our theoretical predictions for the phase behavior and the density profiles with Monte Carlo simulations for the semi-infinite system and we find good agreement with our theoretical predictions.

  10. Thermal-cycling-induced spectral diffusion and thermal barriers in anisole-doped cyclohexane, an unusual multiphase host-guest system.

    PubMed

    Somoza, Mark M; Friedrich, Josef

    2006-09-28

    The host-guest system of anisole incorporated into a cyclohexane matrix was investigated in a series of hole-burning experiments. This system is unusual in that cyclohexane can freeze into coexisting solid phases. The hole-burning experiments support the existence of two crystalline phases and one disordered phase. A second surprising characteristic of this system is that the quasi-line absorption features of the spectra appear inverted at low temperature because of unexpected dominance of fluorescence and phosphorescence.

  11. Removing heavy metals using permeable pavement system with a titanate nano-fibrous adsorbent column as a post treatment.

    PubMed

    Sounthararajah, Danious Pratheep; Loganathan, Paripurnanda; Kandasamy, Jayakumar; Vigneswaran, Saravanamuthu

    2017-02-01

    Permeable pavement systems (PPS) are a widely-used treatment measure in sustainable stormwater management and groundwater recharge. However, PPS are not very efficient in removing heavy metals from stormwater. A pilot scale study using zeolite or basalt as bed material in PPS removed 41-72%, 67-74%, 38-43%, 61-72%, 63-73% of Cd, Cu, Ni, Pb, and Zn, respectively, from synthetic stormwater (pH 6.5; Cd, Cu, Ni, Pb, and Zn concentrations of 0.04, 0.6, 0.06, 1.0, and 2.0 mg L(-1), respectively) over a period of 80 h. The total volume of stormwater that passed through the PPS was equivalent to runoff in 10 years of rainfall in Sydney, Australia. The concentrations of metals in the PPS effluent failed fresh and marine water quality trigger values recommended in the Australian and New Zealand guidelines. An addition of a post-treatment of a horizontal filter column containing a titanate nano-fibrous (TNF) material with a weight < 1% of zeolite weight and mixed in with granular activated carbon (GAC) at a GAC:TNF weight ratio of 25:1 removed 77% of Ni and 99-100% of all the other metals. The effluent easily met the required standards of marine waters and just met those concerning fresh waters. Batch adsorption data from solutions of metals mixtures fitted the Langmuir model with adsorption capacities in the following order, TNF ≫ zeolite > basalt; Pb > Cu > Cd, Ni, Zn.

  12. Multiphase Instabilities in Explosive Dispersal of Particles

    NASA Astrophysics Data System (ADS)

    Rollin, Bertrand; Ouellet, Frederick; Annamalai, Subramanian; Balachandar, S. ``Bala''

    2015-11-01

    Explosive dispersal of particles is a complex multiphase phenomenon that can be observed in volcanic eruptions or in engineering applications such as multiphase explosives. As the layer of particles moves outward at high speed, it undergoes complex interactions with the blast-wave structure following the reaction of the energetic material. Particularly in this work, we are interested in the multiphase flow instabilities related to Richmyer-Meshkov (RM) and Rayleigh-Taylor (RM) instabilities (in the gas phase and particulate phase), which take place as the particle layer disperses. These types of instabilities are known to depend on initial conditions for a relatively long time of their evolution. Using a Eulerian-Lagrangian approach, we study the growth of these instabilities and their dependence on initial conditions related to the particulate phase - namely, (i) particle size, (ii) initial distribution, and (iii) mass ratio (particles to explosive). Additional complexities associated with compaction of the layer of particles are avoided here by limiting the simulations to modest initial volume fraction of particles. A detailed analysis of the initial conditions and its effects on multiphase RM/RT-like instabilities in the context of an explosive dispersal of particles is presented. This work was supported by the U.S. Department of Energy, National Nuclear Security Administration, Advanced Simulation and Computing Program, as a Cooperative Agreement under the Predictive Science Academic Alliance Program, Contract No. DE-NA0002378.

  13. Ultrasonic rate measurement of multiphase flow

    SciTech Connect

    Dannert, D.A.; Horne, R.N.

    1993-01-01

    On of the most important tools in production logging and well testing is the downhole flowmeter. Unfortunately, existing tools are inaccurate outside of an idealized single phase flow, regime. Spinner tools are inaccurate at extremely high or low, flow rates and when the flow rate is variable. Radioactive tracer tools have similar inaccuracies and are extremely sensitive to the flow regime. Both tools completely fail in the presence of multiphase flow, whether gas/ oil, gas/water or fluid/solid. Downhole flowmetering is important for locating producing zones and thief zones and monitoring production and injection rates. The effects of stimulation can also be determined. This goal of this project is the investigation of accurate downhole flowmetering techniques for all single phase flow regimes and multiphase flows. The measurement method investigated in this report is the use of ultrasound. There are two ways to use ultrasound for fluid velocity measurement. The first method, examined in Chapter 2, is the contrapropagation, or transit-time, method which compares travel times with and against fluid flow. Chapter 3 details the second method which measures the Doppler frequency shift of a reflected sound wave in the moving fluid. Both of these technologies need to be incorporated in order to build a true multiphase flowmeter. Chapter 4 describes the proposed downhole multiphase flowmeter. It has many advantages besides the ones previously mentioned and is in full in that chapter.

  14. Multi-Phase Driver Education Teaching Guide.

    ERIC Educational Resources Information Center

    Hurst-Euless-Bedford Independent School District, Hurst, TX.

    For use in planning and conducting functional multi-phase driver education programs, this teacher's guide consists of four phases of instruction: classroom activities, simulated application, in-car range practice, and in-car public practice. Contents are divided into three instructional sections, with the first combining the classroom activities…

  15. A Gallium Multiphase Equation of State

    NASA Astrophysics Data System (ADS)

    Crockett, Scott; Greeff, Carl

    2009-06-01

    A new SESAME multiphase gallium equation of state (EOS) has been developed. The equation of state includes two of the solid phases (Ga I, Ga III) and a fluid phase. The EOS includes consistent latent heat between the phases. We compare the results to the liquid Hugoniot data. We will also explore refreezing via isentropic release and compression.

  16. Cavitation and multiphase flow forum - 1987

    SciTech Connect

    Furuya, O

    1987-01-01

    These proceedings collect papers on cavitation phenomena. Topics include: multiphase flow, the two-phase water hammer in a nuclear power plant, phase separation of dispersed annular flow, liquid films, shock waves propagating through two-phase magnetic fluid, venturimeters, gas-particle flows, particle-wall interactions, and the evaluation of wear in centrifugal slurry pumps.

  17. The development of the Minnesota Multiphasic Personality Inventory.

    PubMed

    Buchanan, R D

    1994-04-01

    The Minnesota Multiphasic Personality Inventory (MMPI) was constructed at the University of Minnesota before and during World War II. In its developmental phase, the MMPI was conceptualized as an efficient way of detecting psychiatric disturbance. The test's construction was made possible by atypical cooperation between psychologists and psychiatrists, within the context of a crisis in the U.S. public mental health care system. The MMPI was designed to meet the diagnostic needs of psychiatrists. As such, it represented the operationalization of medical hegemony. However, the interpretation of the MMPI shifted significantly after the war, reflecting organizational reform in clinical psychology and changing professional relationships between psychologists and psychiatrists.

  18. Advanced material distribution measurement in multiphase flows: A case study

    SciTech Connect

    George, D.L.; Ceccio, S.L.; O`Hern, T.J.; Shollenberger, K.A.; Torczynski, J.R.

    1998-08-01

    A variety of tomographic techniques that have been applied to multiphase flows are described. The methods discussed include electrical impedance tomography (EIT), magnetic resonance imaging (MRI), positron emission tomography (PET), gamma-densitometry tomography (GDT), radiative particle tracking (RDT), X-ray imaging, and acoustic tomography. Also presented is a case study in which measurements were made with EIT and GDT in two-phase flows. Both solid-liquid and gas-liquid flows were examined. EIT and GDT were applied independently to predict mean and spatially resolved phase volume fractions. The results from the two systems compared well.

  19. Metrological effectiveness of an analytical method for volatile organic compounds standard materials using post-column reaction GC/FID system.

    PubMed

    Watanabe, Takuro; Kato, Kenji; Tsunoda, Kin-ichi; Maeda, Tsuneaki

    2008-06-30

    The metrological effectiveness of an analytical method using the post-column reaction GC/FID system was evaluated. The SI-traceable certified reference material (CRM), the eight ester phthalates mixture standard solution, was used as a sample. We assigned specific value to n-eicosane and it was used as an internal standard. A known quantity of n-eicosane was added to the CRM, and the mixture was measured with the post-column reaction GC/FID system. Six phthalate esters were chromatographically separated and determined. The assigned values by our system are in good agreement with the certified values of the CRM, and the combined uncertainties of the measurements by the present system were better than those of the CRM. Our method is classified as a primary ratio method and the specific values of many organic compounds can be assigned very precisely by using a small number of reference materials. Also, the method can make it possible to avoid the purity determination of raw materials and directly to assign their specific values after the preparation of the standard mixture. Conclusively, this post-column reaction GC/FID system is very effective for the chemical metrology.

  20. Multiphase Ozonolysis of Aqueous α-Terpineol.

    PubMed

    Leviss, Dani H; Van Ry, Daryl A; Hinrichs, Ryan Z

    2016-11-01

    Multiphase ozonolysis of aqueous organics presents a potential pathway for the formation of aqueous secondary organic aerosol (aqSOA). We investigated the multiphase ozonolysis of α-terpineol, an oxygenated derivative of limonene, and found that the reaction products and kinetics differ from the gas-phase ozonolysis of α-terpineol. One- and two-dimensional NMR spectroscopies along with GC-MS identified the aqueous ozonolysis reaction products as trans- and cis-lactols [4-(5-hydroxy-2,2-dimethyltetrahydrofuran-3-yl)butan-2-one] and a lactone [4-hydroxy-4-methyl-3-(3-oxobutyl)-valeric acid gamma-lactone], which accounted for 46%, 27%, and 20% of the observed products, respectively. Hydrogen peroxide was also formed in 10% yield consistent with a mechanism involving decomposition of hydroxyl hydroperoxide intermediates followed by hemiacetal ring closure. Multiphase reaction kinetics at gaseous ozone concentrations of 131, 480, and 965 parts-per-billion were analyzed using a resistance model of net ozone uptake and found the second-order rate coefficient for the aqueous reaction of α-terpineol + O3 to be 9.9(±3.3) × 10(6) M(-1) s(-1). Multiphase ozonolysis will therefore be competitive with multiphase oxidation by hydroxyl radicals (OH) and ozonolysis of gaseous α-terpineol. We also measured product yields for the heterogeneous ozonolysis of α-terpineol adsorbed on glass, NaCl, and kaolinite, and identified the same three major products but with an increasing lactone yield of 33, 49, and 55% on these substrates, respectively.

  1. Fluoxetine and norfluoxetine analysis by direct injection of human plasma in a column switching liquid chromatographic system.

    PubMed

    Santos-Neto, Alvaro J; Fernandes, Christian; Rodrigues, José C; Alves, Claudete; Lanças, Fernando M

    2008-01-01

    A column switching LC method is presented for the analysis of fluoxetine (FLU) and norfluoxetine (NFLU) by direct injection of human plasma using a lab-made restricted access media (RAM) column. A RAM-BSA-octadecyl silica (C-18) column (40 mm x 4.6 mm, 10 microm) is evaluated in both backflush and foreflush elution modes and coupled with a C-18 lab-made (50 mm x 4.6 mm, 3 microm) analytical column in order to perform online sample preparation. Direct injection of 100 microL of plasma samples is possible with the developed approach. In addition, reduction of sample handling is obtained when compared with traditional liquid-liquid extraction (LLE) and SPE. The total analysis time is around 20 min. A LOQ of 15 ng/mL is achieved in a concentration range of 15-500 ng/mL, allowing the therapeutic drug monitoring of clinical samples. The precision values achieved are lower than 15% for all the evaluated points with adequate recovery and accuracy. Furthermore, no matrix interferences are found in the analysis and the proposed method shows to be an adequate alternative for analysis of FLU in plasma.

  2. Multiphase Flow Modeling of Biofuel Production Processes

    SciTech Connect

    D. Gaston; D. P. Guillen; J. Tester

    2011-06-01

    As part of the Idaho National Laboratory's (INL's) Secure Energy Initiative, the INL is performing research in areas that are vital to ensuring clean, secure energy supplies for the future. The INL Hybrid Energy Systems Testing (HYTEST) Laboratory is being established to develop and test hybrid energy systems with the principal objective to safeguard U.S. Energy Security by reducing dependence on foreign petroleum. HYTEST involves producing liquid fuels in a Hybrid Energy System (HES) by integrating carbon-based (i.e., bio-mass, oil-shale, etc.) with non-carbon based energy sources (i.e., wind energy, hydro, geothermal, nuclear, etc.). Advances in process development, control and modeling are the unifying vision for HES. This paper describes new modeling tools and methodologies to simulate advanced energy processes. Needs are emerging that require advanced computational modeling of multiphase reacting systems in the energy arena, driven by the 2007 Energy Independence and Security Act, which requires production of 36 billion gal/yr of biofuels by 2022, with 21 billion gal of this as advanced biofuels. Advanced biofuels derived from microalgal biomass have the potential to help achieve the 21 billion gal mandate, as well as reduce greenhouse gas emissions. Production of biofuels from microalgae is receiving considerable interest due to their potentially high oil yields (around 600 gal/acre). Microalgae have a high lipid content (up to 50%) and grow 10 to 100 times faster than terrestrial plants. The use of environmentally friendly alternatives to solvents and reagents commonly employed in reaction and phase separation processes is being explored. This is accomplished through the use of hydrothermal technologies, which are chemical and physical transformations in high-temperature (200-600 C), high-pressure (5-40 MPa) liquid or supercritical water. Figure 1 shows a simplified diagram of the production of biofuels from algae. Hydrothermal processing has significant

  3. Performance evaluation of granular activated carbon system at Pantex: Rapid small-scale column tests to simulate removal of high explosives from contaminated groundwater

    SciTech Connect

    Henke, J.L.; Speitel, G.E.

    1998-08-01

    A granular activated carbon (GAC) system is now in operation at Pantex to treat groundwater from the perched aquifer that is contaminated with high explosives. The main chemicals of concern are RDX and HMX. The system consists of two GAC columns in series. Each column is charged with 10,000 pounds of Northwestern LB-830 GAC. At the design flow rate of 325 gpm, the hydraulic loading is 6.47 gpm/ft{sup 2}, and the empty bed contact time is 8.2 minutes per column. Currently, the system is operating at less than 10% of its design flow rate, although flow rate increases are expected in the relatively near future. This study had several objectives: Estimate the service life of the GAC now in use at Pantex; Screen several GACs to provide a recommendation on the best GAC for use at Pantex when the current GAC is exhausted and is replaced; Determine the extent to which natural organic matter in the Pantex groundwater fouls GAC adsorption sites, thereby decreasing the adsorption capacity for high explosives; and Determine if computer simulation models could match the experimental results, thereby providing another tool to follow system performance.

  4. Americium, Cesium, and Plutonium Colloid-Facilitated Transport in a Groundwater/Bentonite/Fracture Fill Material System: Column Experiments and Model Results

    NASA Astrophysics Data System (ADS)

    Dittrich, T. M.; Boukhalfa, H.; Reimus, P. W.

    2014-12-01

    The objective of this study was to investigate and quantify the effects of desorption kinetics and colloid transport on radionuclides with different sorption affinities. We focused on quantifying transport mechanisms important for upscaling in time and distance. This will help determine the long-term fate and transport of radionuclides to aid in risk assessments. We selected a fractured/weathered granodiorite at the Grimsel Test Site (GTS) in Switzerland as a model crystalline rock repository system because the system has been thoroughly studied and field experiments involving radionuclides have already been conducted. Working on this system provides a unique opportunity to compare lab experiments with field-scale observations. Weathered fracture fill material (FFM) and bentonite used as backfill at the GTS were characterized (e.g., BET, SEM/EDS, QXRD), and batch and breakthrough column experiments were conducted. Solutions were prepared in synthetic groundwaters that matched the natural water chemistry. FFM samples were crushed, rinsed, sieved (150-355 μm), and equilibrated with synthetic groundwater. Bentonite was crushed, sodium-saturated, equilibrated with synthetic groundwater, and settled to yield a stable suspension. Suspensions were equilibrated with Am, Cs, or Pu. All experiments were conducted with Teflon®materials to limit sorption to system components. After radionuclide/colloid injections reached stability, radionuclide-free solutions were injected to observe the desorption and release behavior. Aliquots of effluent were measured for pH, colloid concentration, and total and dissolved radionuclides. Unanalyzed effluent from the first column was then injected through a second column of fresh material. The process was repeated for a third column and the results of all three breakthrough curves were modeled with a multi-site/multi-rate MATLAB code to elucidate the sorption rate coefficients and binding site densities of the bentonite colloids and

  5. Experimental assessment and modeling of interphase mass transfer rates of organic compounds in multiphase subsurface systems. Final report, July 1, 1989--June 30, 1993

    SciTech Connect

    Abriola, L.M.; Weber, W.J. Jr.

    1993-10-01

    Results of an experimental investigation into strady state dissolution of nonaqueous phase liquids (NAPLS) entrapped within water saturated porous media are presented. Influence of porous media type, NAPL characteristics, and aqueous phase flow velocity are examined for transient and steady-state dissolution of NAPL. Entrapped NAPL distributions are examined and are found to influence mass transfer between the phases. A phenomenological model for the steady state mass transfer process is developed which expresses a lumped mass transfer coefficient as a function of the hydrodynamics of the system and grain size parameters as a surrogate measure of the NAPL distribution. Transient dissolution data is used to develop two alternative phenomenological models for mass transfer. The models are incorporated into a onedimensional numerical simulator and are shown to be effective predictors of transient dissolution data in similar experimental systems. In order to further explore the effects of scale and heterogeneities on NAPL dissolution, the sphere model is incorporated into a two-dimensional simulator and is used to explore long-term dissolution of a TCE (trichloroethylene) spill in a layered system of sands. The simulation demonstrates the significance of heterogeneity, both in controlling the initial distribution of NAPL and the rate of NAPL dissolution.

  6. Self-regenerating column chromatography

    DOEpatents

    Park, W.K.

    1995-05-30

    The present invention provides a process for treating both cations and anions by using a self-regenerating, multi-ionic exchange resin column system which requires no separate regeneration steps. The process involves alternating ion-exchange chromatography for cations and anions in a multi-ionic exchange column packed with a mixture of cation and anion exchange resins. The multi-ionic mixed-charge resin column works as a multi-function column, capable of independently processing either cationic or anionic exchange, or simultaneously processing both cationic and anionic exchanges. The major advantage offered by the alternating multi-function ion exchange process is the self-regeneration of the resins.

  7. Microstructure and properties of multiphase and functionally graded materials prepared by chemical vapor deposition

    SciTech Connect

    Lee, W.Y.

    1996-05-01

    The synthesis of multiphase and functionally graded materials by chemical vapor deposition is discussed from a perspective of controlling their composition and microstructure at a nano-scale level, and ultimately, tailoring their material properties. Prior research is briefly reviewed to address the current state of this novel material concept. Recent experimental results relating to controlling the selected properties of two multiphase systems, TiN + MoS{sub 2} and NiAl + Al{sub 2}O{sub 3}, are described to illustrate this concept`s potential merits and challenges for use in realistic applications.

  8. Some Specific CASL Requirements for Advanced Multiphase Flow Simulation of Light Water Reactors

    SciTech Connect

    R. A. Berry

    2010-11-01

    Because of the diversity of physical phenomena occuring in boiling, flashing, and bubble collapse, and of the length and time scales of LWR systems, it is imperative that the models have the following features: • Both vapor and liquid phases (and noncondensible phases, if present) must be treated as compressible. • Models must be mathematically and numerically well-posed. • The models methodology must be multi-scale. A fundamental derivation of the multiphase governing equation system, that should be used as a basis for advanced multiphase modeling in LWR coolant systems, is given in the Appendix using the ensemble averaging method. The remainder of this work focuses specifically on the compressible, well-posed, and multi-scale requirements of advanced simulation methods for these LWR coolant systems, because without these are the most fundamental aspects, without which widespread advancement cannot be claimed. Because of the expense of developing multiple special-purpose codes and the inherent inability to couple information from the multiple, separate length- and time-scales, efforts within CASL should be focused toward development of a multi-scale approaches to solve those multiphase flow problems relevant to LWR design and safety analysis. Efforts should be aimed at developing well-designed unified physical/mathematical and high-resolution numerical models for compressible, all-speed multiphase flows spanning: (1) Well-posed general mixture level (true multiphase) models for fast transient situations and safety analysis, (2) DNS (Direct Numerical Simulation)-like models to resolve interface level phenmena like flashing and boiling flows, and critical heat flux determination (necessarily including conjugate heat transfer), and (3) Multi-scale methods to resolve both (1) and (2) automatically, depending upon specified mesh resolution, and to couple different flow models (single-phase, multiphase with several velocities and pressures, multiphase with single

  9. The dual temperature/pH-sensitive multiphase behavior of poly(N-isopropylacrylamide-co-acrylic acid) microgels for potential application in in situ gelling system.

    PubMed

    Xiong, Wei; Gao, Xiang; Zhao, Yanbing; Xu, Huibi; Yang, Xiangliang

    2011-05-01

    Poly(N-isopropylacrylamide-co-acrylic acid) microgels (PNA) may be an excellent formulation for in situ gelling system due to their high sensitivity and fast response rate. Four monodispersed PNA microgels with various contents of acrylic acid (AA) were synthesized by emulsion polymerization in this paper. Their hydrodynamic diameters decreased reversibly with both decreasing pH and increasing temperature. The dual temperature/pH-sensitivity was influenced by many factors such as AA content, cross-link density and ion strength. In addition, high concentration PNA dispersions underwent multiple phase transition according to different temperatures, pHs and concentrations, which were summarized in a 3D sol-gel phase diagram in this study. According to the sol-gel phase transition, 8% PNA-025 dispersion maintained a relatively low viscosity and favorable fluidity at pH 5.0 in the temperature range of 25-40°C, but it rapidly increased in viscosity at pH 7.4 and gelled at 37°C. This feature enabled the dual temperature/pH-sensitive microgels to overcome the troubles in syringing of temperature sensitive materials during the injection. Apart from this, PNA could form gel well in in vitro (e.g., medium and serum) and in in vivo with low cytotoxicity. Therefore, it is promising for PNA to be applied in the in situ gelling system.

  10. More Constraints on the Physical Conditions of the Kinematically Complex, Multiphase Absorption Line System at z=0.93 toward PG1206+459

    NASA Astrophysics Data System (ADS)

    Rosenwasser, Ben; Muzahid, Sowgat; Norris, Jackson; Charlton, Jane C.

    2015-01-01

    We present the results of photo- and collisional ionization modeling of the strong MgII absorption system at redshift z~0.93 towards the quasar PG1206+459. This system has been extensively studied over the last two decades (Churchill & Charlton 1999; Ding et al. 2003; Tripp et al. 2011) using a combination of spectra from Keck/HIRES, HST/FOS, HST/STIS, and HST/COS. Here we present newconstraints using the most complete spectral coverage including more recent observations of OVI and the Lyman series from HST/COS. Numerous absorption components are seen over a large velocity spread (~1500km/s), and multiple ionization phases are required to account for the detected transitions, which include MgI, MgII, FeII, SiII, SiIII, SiIV, CII, CIII, CIV, SIII, SIV, SV, SVI, NIII, NIV, NV, OIII, OIV, OV, OVI, and NeVIII. Considering the new constraints, we revisit the question of the physical nature of the structures that produce this absorber.

  11. Antibacterial behavior of silver-modified clinoptilolite-heulandite rich tuff on coliform microorganisms from wastewater in a column system.

    PubMed

    De la Rosa-Gómez, I; Olguín, M T; Alcántara, D

    2008-09-01

    . Therefore the amount of bactericide agent (silver-modified natural zeolite), coliform microorganisms from water (E. coli or consort of coliform microorganisms) as well as the water quality (synthetic wastewater or municipal wastewater) influenced both the disinfection process and the silver recovery in a column system.

  12. Evaluation of a coupled model for numerical simulation of a multiphase flow system in a porous medium and a surface fluid.

    PubMed

    Hibi, Yoshihiko; Tomigashi, Akira

    2015-09-01

    Numerical simulations that couple flow in a surface fluid with that in a porous medium are useful for examining problems of pollution that involve interactions among atmosphere, water, and groundwater, including saltwater intrusion along coasts. Coupled numerical simulations of such problems must consider both vertical flow between the surface fluid and the porous medium and complicated boundary conditions at their interface. In this study, a numerical simulation method coupling Navier-Stokes equations for surface fluid flow and Darcy equations for flow in a porous medium was developed. Then, the basic ability of the coupled model to reproduce (1) the drawdown of a surface fluid observed in square-pillar experiments, using pillars filled with only fluid or with fluid and a porous medium and (2) the migration of saltwater (salt concentration 0.5%) in the porous medium using the pillar filled with fluid and a porous medium was evaluated. Simulations that assumed slippery walls reproduced well the results with drawdowns of 10-30 cm when the pillars were filled with packed sand, gas, and water. Moreover, in the simulation of saltwater infiltration by the method developed in this study, velocity was precisely reproduced because the experimental salt concentration in the porous medium after saltwater infiltration was similar to that obtained in the simulation. Furthermore, conditions across the boundary between the porous medium and the surface fluid were satisfied in these numerical simulations of square-pillar experiments in which vertical flow predominated. Similarly, the velocity obtained by the simulation for a system coupling flow in surface fluid with that in a porous medium when horizontal flow predominated satisfied the conditions across the boundary. Finally, it was confirmed that the present simulation method was able to simulate a practical-scale surface fluid and porous medium system. All of these numerical simulations, however, required a great deal of

  13. Basin-Scale Study on the Multiphase Distribution, Source Apportionment and Risk Assessment of PAHs in the Hai River Water System.

    PubMed

    Li, Rufeng; Zhang, Xian'e; Liu, Yanzhen; Yin, Su; Liu, Jingling; Feng, Chenghong

    2016-10-01

    As a systematic research at basin scale, this study explored the composition and concentration characteristics of 16 priority polycyclic aromatic hydrocarbons (PAHs) in sediments, water, and suspended particulate matter (SPM) in the water systems (rivers, lakes, and reservoirs) in the Hai River Basin through literature review. The sources and the ecosystem risks of PAHs in the sediments in the entire basin were specially discussed with diagnostic ration, PAHs composition, and an improved risk quotient method. Results showed that the total concentration of PAHs varied from 99.65 to 25,303 ng g(-1) dry weight in sediments, from 51.0 to 559.1 ng L(-1) in water, and from 4528 to 51,080 ng g(-1) dry weight in SPM, respectively. The dominant PAHs in the three examined phases were 2-3 rings in most waterbodies. PAHs in the rivers were from mixed sources (petrogenic and pyrolytic inputs), whereas those in lakes and reservoirs were mainly from biomass combustion and petroleum combustion. PAHs in the entire basin exhibited moderate to high ecological risk, and the rivers (especially Hai River, Jiyun River, Chaobai River, and Beiyun River) suffered higher ecological risk than reservoirs and lakes. Most of the rivers with higher PAHs risk flow through or around megacity Beijing and Tianjin.

  14. Elastic registration of multiphase CT images of liver

    NASA Astrophysics Data System (ADS)

    Heldmann, Stefan; Zidowitz, Stephan

    2009-02-01

    In this work we present a novel approach for elastic image registration of multi-phase contrast enhanced CT images of liver. A problem in registration of multiphase CT is that the images contain similar but complementary structures. In our application each image shows a different part of the vessel system, e.g., portal/hepatic venous/arterial, or biliary vessels. Portal, arterial and biliary vessels run in parallel and abut on each other forming the so called portal triad, while hepatic veins run independent. Naive registration will tend to align complementary vessel. Our new approach is based on minimizing a cost function consisting of a distance measure and a regularizer. For the distance we use the recently proposed normalized gradient field measure that focuses on the alignment of edges. For the regularizer we use the linear elastic potential. The key feature of our approach is an additional penalty term using segmentations of the different vessel systems in the images to avoid overlaps of complementary structures. We successfully demonstrate our new method by real data examples.

  15. Factors Controlling the Properties of Multi-Phase Arctic Stratocumulus Clouds

    NASA Technical Reports Server (NTRS)

    Fridlind, Ann; Ackerman, Andrew; Menon, Surabi

    2005-01-01

    The 2004 Multi-Phase Arctic Cloud Experiment (M-PACE) IOP at the ARM NSA site focused on measuring the properties of autumn transition-season arctic stratus and the environmental conditions controlling them, including concentrations of heterogeneous ice nuclei. Our work aims to use a large-eddy simulation (LES) code with embedded size-resolved aerosol and cloud microphysics to identify factors controlling multi-phase arctic stratus. Our preliminary simulations of autumn transition-season clouds observed during the 1994 Beaufort and Arctic Seas Experiment (BASE) indicated that low concentrations of ice nuclei, which were not measured, may have significantly lowered liquid water content and thereby stabilized cloud evolution. However, cloud drop concentrations appeared to be virtually immune to changes in liquid water content, indicating an active Bergeron process with little effect of collection on drop number concentration. We will compare these results with preliminary simulations from October 8-13 during MPACE. The sensitivity of cloud properties to uncertainty in other factors, such as large-scale forcings and aerosol profiles, will also be investigated. Based on the LES simulations with M-PACE data, preliminary results from the NASA GlSS single-column model (SCM) will be used to examine the sensitivity of predicted cloud properties to changing cloud drop number concentrations for multi-phase arctic clouds. Present parametrizations assumed fixed cloud droplet number concentrations and these will be modified using M-PACE data.

  16. Denitrification in a low-temperature bioreactor system at two different hydraulic residence times: laboratory column studies.

    PubMed

    Nordström, Albin; Herbert, Roger B

    2016-09-15

    Nitrate removal rates in a mixture of pine woodchips and sewage sludge were determined in laboratory column studies at 5°C, 12°C, and 22°C, and at two different hydraulic residence times (HRTs; 58.2-64.0 hours and 18.7-20.6 hours). Baffles installed in the flow path were tested as a measure to reduce preferential flow behavior, and to increase the nitrate removal in the columns. The nitrate removal in the columns was simulated at 5°C and 12°C using a combined Arrhenius-Monod equation controlling the removal rate, and a first-order exchange model for incorporation of stagnant zones. Denitrification in the mixture of pine woodchips and sewage sludge reduced nitrate concentrations of 30 mg N L(-1) at 5°C to below detection limits at a HRT of 58.2-64.0 hours. At a HRT of 18.7-20.6 hours, nitrate removal was incomplete. The Arrhenius frequency factor and activation energy retrieved from the low HRT data supported a biochemically controlled reaction rate; the same parameters, however, could not be used to simulate the nitrate removal at high HRT. The results show an inversely proportional relationship between the advection velocity and the nitrate removal rate, suggesting that bioreactor performance could be enhanced by promoting low advection velocities.

  17. Error handling strategies in multiphase inverse modeling

    SciTech Connect

    Finsterle, S.; Zhang, Y.

    2010-12-01

    Parameter estimation by inverse modeling involves the repeated evaluation of a function of residuals. These residuals represent both errors in the model and errors in the data. In practical applications of inverse modeling of multiphase flow and transport, the error structure of the final residuals often significantly deviates from the statistical assumptions that underlie standard maximum likelihood estimation using the least-squares method. Large random or systematic errors are likely to lead to convergence problems, biased parameter estimates, misleading uncertainty measures, or poor predictive capabilities of the calibrated model. The multiphase inverse modeling code iTOUGH2 supports strategies that identify and mitigate the impact of systematic or non-normal error structures. We discuss these approaches and provide an overview of the error handling features implemented in iTOUGH2.

  18. Development of gas chromatography-flame ionization detection system with a single column and liquid nitrogen-free for measuring atmospheric C2-C12 hydrocarbons.

    PubMed

    Liu, Chengtang; Mu, Yujing; Zhang, Chenglong; Zhang, Zhibo; Zhang, Yuanyuan; Liu, Junfeng; Sheng, Jiujiang; Quan, Jiannong

    2016-01-04

    A liquid nitrogen-free GC-FID system equipped with a single column has been developed for measuring atmospheric C2-C12 hydrocarbons. The system is consisted of a cooling unit, a sampling unit and a separation unit. The cooling unit is used to meet the temperature needs of the sampling unit and the separation unit. The sampling unit includes a dehydration tube and an enrichment tube. No breakthrough of the hydrocarbons was detected when the temperature of the enrichment tube was kept at -90 °C and sampling volume was 400 mL. The separation unit is a small round oven attached on the cooling column. A single capillary column (OV-1, 30 m × 0.32 mm I.D.) was used to separate the hydrocarbons. An optimal program temperature (-60 ∼ 170 °C) of the oven was achieved to efficiently separate C2-C12 hydrocarbons. There were good linear correlations (R(2)=0.993-0.999) between the signals of the hydrocarbons and the enrichment amount of hydrocarbons, and the relative standard deviation (RSD) was less than 5%, and the method detection limits (MDLs) for the hydrocarbons were in the range of 0.02-0.10 ppbv for sampling volume of 400 mL. Field measurements were also conducted and more than 50 hydrocarbons from C2 to C12 were detected in Beijing city.

  19. Column Liquid Chromatography.

    ERIC Educational Resources Information Center

    Majors, Ronald E.; And Others

    1984-01-01

    Reviews literature covering developments of column liquid chromatography during 1982-83. Areas considered include: books and reviews; general theory; columns; instrumentation; detectors; automation and data handling; multidimensional chromatographic and column switching techniques; liquid-solid chromatography; normal bonded-phase, reversed-phase,…

  20. A Gallium multiphase equation of state

    SciTech Connect

    Crockett, Scott D; Greeff, Carl

    2009-01-01

    A new SESAME multiphase Gallium equation of state (EOS) has been developed. The equation of state includes three of the solid phases (Ga I, Ga II, Ga III) and a fluid phase (liquid/gas). The EOS includes consistent latent heat between the phases. We compare the results to the liquid Hugoniol data. We also explore the possibility of re-freezing via dynamic means such as isentropic and shock compression.

  1. a Gallium Multiphase Equation of State

    NASA Astrophysics Data System (ADS)

    Crockett, Scott D.; Greeff, Carl W.

    2009-12-01

    A new SESAME multiphase Gallium equation of state (EOS) has been developed. It includes three of the solid phases (Ga I, Ga II, Ga III) and a fluid phase (liquid/gas). The EOS includes consistent latent heat between the phases. We compare the results to the liquid Hugoniot data. We also explore the possibility of re-freezing via dynamic means such as isentropic and shock compression. We predict an unusual spontaneous spreading of low pressure shocks from STP.

  2. Modified Invasion Percolation Models for Multiphase Processes

    SciTech Connect

    Karpyn, Zuleima

    2015-01-31

    This project extends current understanding and modeling capabilities of pore-scale multiphase flow physics in porous media. High-resolution X-ray computed tomography imaging experiments are used to investigate structural and surface properties of the medium that influence immiscible displacement. Using experimental and computational tools, we investigate the impact of wetting characteristics, as well as radial and axial loading conditions, on the development of percolation pathways, residual phase trapping and fluid-fluid interfacial areas.

  3. Practical aspects and uncertainty analysis of biological effective dose (BED) regarding its three-dimensional calculation in multiphase radiotherapy treatment plans

    SciTech Connect

    Kauweloa, Kevin I. Gutierrez, Alonso N.; Bergamo, Angelo; Stathakis, Sotirios; Papanikolaou, Nikos; Mavroidis, Panayiotis

    2014-07-15

    Purpose: There is a growing interest in the radiation oncology community to use the biological effective dose (BED) rather than the physical dose (PD) in treatment plan evaluation and optimization due to its stronger correlation with radiobiological effects. Radiotherapy patients may receive treatments involving a single only phase or multiple phases (e.g., primary and boost). Since most treatment planning systems cannot calculate the analytical BED distribution in multiphase treatments, an approximate multiphase BED expression, which is based on the total physical dose distribution, has been used. The purpose of this paper is to reveal the mathematical properties of the approximate BED formulation, relative to the true BED. Methods: The mathematical properties of the approximate multiphase BED equation are analyzed and evaluated. In order to better understand the accuracy of the approximate multiphase BED equation, the true multiphase BED equation was derived and the mathematical differences between the true and approximate multiphase BED equations were determined. The magnitude of its inaccuracies under common clinical circumstances was also studied. All calculations were performed on a voxel-by-voxel basis using the three-dimensional dose matrices. Results: Results showed that the approximate multiphase BED equation is accurate only when the dose-per-fractions (DPFs) in both the first and second phases are equal, which occur when the dose distribution does not significantly change between the phases. In the case of heterogeneous dose distributions, which significantly vary between the phases, there are fewer occurrences of equal DPFs and hence the inaccuracy of the approximate multiphase BED is greater. These characteristics are usually seen in the dose distributions being delivered to organs at risk rather than to targets. Conclusions: The finding of this study indicates that the true multiphase BED equation should be implemented in the treatment planning

  4. Interface effects on multiphase flows in porous media

    SciTech Connect

    Zhang, Duan Z

    2008-01-01

    Most models for multiphase flows in a porous medium are based on the straightforward extension of Darcy's law, in which each fluid phase is driven by its own pressure gradient. The pressure difference between the phases is thought to be an effect of surface tension and is called capillary pressure. Independent of Darcy's law, for liquid imbibition processes in a porous material, diffusion models are sometime used. In this paper, an ensemble phase averaging technique for continuous multi phase flows is applied to derive averaged equations and to examine the validity of the commonly used models. The closure for the averaged equations is quite complicated for general multiphase flows in a porous material. For flows with a small ratio of the characteristic length of the phase interfaces to the macroscopic length, the closure relations can be simplified significantly by an approximation with a second order error in the length ratio. The approximation reveals the information of the length scale separation obscured during the ensemble averaging process, and leads to an equation system similar to Darcy's law, but with additional terms. Based on interactions on phase interfaces, relations among closure quantities are studied.

  5. Artificial neural network (ANN) modeling of adsorption of methylene blue by NaOH-modified rice husk in a fixed-bed column system.

    PubMed

    Chowdhury, Shamik; Saha, Papita Das

    2013-02-01

    In this study, rice husk was modified with NaOH and used as adsorbent for dynamic adsorption of methylene blue (MB) from aqueous solutions. Continuous removal of MB from aqueous solutions was studied in a laboratory scale fixed-bed column packed with NaOH-modified rice husk (NMRH). Effect of different flow rates and bed heights on the column breakthrough performance was investigated. In order to determine the most suitable model for describing the adsorption kinetics of MB in the fixed-bed column system, the bed depth service time (BDST) model as well as the Thomas model was fitted to the experimental data. An artificial neural network (ANN)-based model was also developed for describing the dynamic dye adsorption process. An extensive error analysis was carried out between experimental data and data predicted by the models by using the following error functions: correlation coefficient (R(2)), average relative error, sum of the absolute error and Chi-square statistic test (χ(2)). Results show that with increasing bed height and decreasing flow rate, the breakthrough time was delayed. All the error functions yielded minimum values for the ANN model than the traditional models (BDST and Thomas), suggesting that the ANN model is the most suitable model to describe the fixed-bed adsorption of MB by NMRH. It is also more rational and reliable to interpret dynamic dye adsorption data through a process of ANN architecture.

  6. Multiphase, multicomponent phase behavior prediction

    NASA Astrophysics Data System (ADS)

    Dadmohammadi, Younas

    Accurate prediction of phase behavior of fluid mixtures in the chemical industry is essential for designing and operating a multitude of processes. Reliable generalized predictions of phase equilibrium properties, such as pressure, temperature, and phase compositions offer an attractive alternative to costly and time consuming experimental measurements. The main purpose of this work was to assess the efficacy of recently generalized activity coefficient models based on binary experimental data to (a) predict binary and ternary vapor-liquid equilibrium systems, and (b) characterize liquid-liquid equilibrium systems. These studies were completed using a diverse binary VLE database consisting of 916 binary and 86 ternary systems involving 140 compounds belonging to 31 chemical classes. Specifically the following tasks were undertaken: First, a comprehensive assessment of the two common approaches (gamma-phi (gamma-ϕ) and phi-phi (ϕ-ϕ)) used for determining the phase behavior of vapor-liquid equilibrium systems is presented. Both the representation and predictive capabilities of these two approaches were examined, as delineated form internal and external consistency tests of 916 binary systems. For the purpose, the universal quasi-chemical (UNIQUAC) model and the Peng-Robinson (PR) equation of state (EOS) were used in this assessment. Second, the efficacy of recently developed generalized UNIQUAC and the nonrandom two-liquid (NRTL) for predicting multicomponent VLE systems were investigated. Third, the abilities of recently modified NRTL model (mNRTL2 and mNRTL1) to characterize liquid-liquid equilibria (LLE) phase conditions and attributes, including phase stability, miscibility, and consolute point coordinates, were assessed. The results of this work indicate that the ϕ-ϕ approach represents the binary VLE systems considered within three times the error of the gamma-ϕ approach. A similar trend was observed for the for the generalized model predictions using

  7. Numerical modeling of experimental observations on gas formation and multi-phase flow of carbon dioxide in subsurface formations

    NASA Astrophysics Data System (ADS)

    Pawar, R.; Dash, Z.; Sakaki, T.; Plampin, M. R.; Lassen, R. N.; Illangasekare, T. H.; Zyvoloski, G.

    2011-12-01

    One of the concerns related to geologic CO2 sequestration is potential leakage of CO2 and its subsequent migration to shallow groundwater resources leading to geochemical impacts. Developing approaches to monitor CO2 migration in shallow aquifer and mitigate leakage impacts will require improving our understanding of gas phase formation and multi-phase flow subsequent to CO2 leakage in shallow aquifers. We are utilizing an integrated approach combining laboratory experiments and numerical simulations to characterize the multi-phase flow of CO2 in shallow aquifers. The laboratory experiments involve a series of highly controlled experiments in which CO2 dissolved water is injected in homogeneous and heterogeneous soil columns and tanks. The experimental results are used to study the effects of soil properties, temperature, pressure gradients and heterogeneities on gas formation and migration. We utilize the Finite Element Heat and Mass (FEHM) simulator (Zyvoloski et al, 2010) to numerically model the experimental results. The numerical models capture the physics of CO2 exsolution, multi-phase fluid flow as well as sand heterogeneity. Experimental observations of pressure, temperature and gas saturations are used to develop and constrain conceptual models for CO2 gas-phase formation and multi-phase CO2 flow in porous media. This talk will provide details of development of conceptual models based on experimental observation, development of numerical models for laboratory experiments and modelling results.

  8. Geochemical observations within the water column at the CO2-rich hydrothermal systems Hatoma Knoll and Yonaguni Knoll IV, in the southern Okinawa Trough

    NASA Astrophysics Data System (ADS)

    Kedzior, Stine; Buß, Antje; Schneider, Bernd; Schneider von Deimling, Jens; Sültenfuß, Jürgen; Walter, Maren; Mertens, Christian; Rehder, Gregor

    2016-09-01

    The Okinawa Trough is one of three known hydrothermal sites worldwide where liquid carbon dioxide is emitted from the seafloor into the water column. In March 2008, investigations were performed at two active areas, Yonaguni Knoll IV and Hatoma Knoll, in order to identify impacts of hydrothermal venting on the water column chemistry. Vertical profiles of pH and redox potential (Eh) were recorded and discrete water samples were taken for the analysis of total carbon dioxide (CT) and helium (3He, 4He). Anomalies with respect to reference stations (ΔCT, ΔpH) and 3He with respect to saturation with the atmosphere (3Heexcess) were used to characterize the impact of hydrothermal vents. These data indicate that the flux of CO2 into the water column is dominated by hot hydrothermal CO2-rich vents located in close proximity to the liquid CO2 emission sites. Bubbles and droplets sampled at the cold gas outlets at Hatoma Knoll differed considerably from the water column regarding CO2/3He ratios, and thus, provide additional evidence that cold liquid phase CO2 is of minor importance for the total CO2 flux at both hydrothermal systems. Although hydrothermal vents at back-arc basins are known to emit large amounts of acids other than CO2, the correlation between ΔpH and ΔCT at both research areas clearly suggests that the observed pH reduction is mainly caused by the addition of CO2. Deviating ΔCT/3He and ΔCT/ΔpH ratios and the prevailing water currents indicate a yet undiscovered vent site at the flank of a seamount in the northeast.

  9. Development of Next Generation Multiphase Pipe Flow Prediction Tools

    SciTech Connect

    Tulsa Fluid Flow

    2008-08-31

    The developments of fields in deep waters (5000 ft and more) is a common occurrence. It is inevitable that production systems will operate under multiphase flow conditions (simultaneous flow of gas-oil-and water possibly along with sand, hydrates, and waxes). Multiphase flow prediction tools are essential for every phase of the hydrocarbon recovery from design to operation. The recovery from deep-waters poses special challenges and requires accurate multiphase flow predictive tools for several applications including the design and diagnostics of the production systems, separation of phases in horizontal wells, and multiphase separation (topside, seabed or bottom-hole). It is very crucial to any multiphase separation technique that is employed either at topside, seabed or bottom-hole to know inlet conditions such as the flow rates, flow patterns, and volume fractions of gas, oil and water coming into the separation devices. The overall objective was to develop a unified model for gas-oil-water three-phase flow in wells, flow lines, and pipelines to predict the flow characteristics such as flow patterns, phase distributions, and pressure gradient encountered during petroleum production at different flow conditions (pipe diameter and inclination, fluid properties and flow rates). The project was conducted in two periods. In Period 1 (four years), gas-oil-water flow in pipes were investigated to understand the fundamental physical mechanisms describing the interaction between the gas-oil-water phases under flowing conditions, and a unified model was developed utilizing a novel modeling approach. A gas-oil-water pipe flow database including field and laboratory data was formed in Period 2 (one year). The database was utilized in model performance demonstration. Period 1 primarily consisted of the development of a unified model and software to predict the gas-oil-water flow, and experimental studies of the gas-oil-water project, including flow behavior description and

  10. On the Grand Challenges in Physical Petrology: the Multiphase Crossroads

    NASA Astrophysics Data System (ADS)

    Bergantz, G. W.

    2014-12-01

    Rapid progress in experimental, micro-analytical and textural analysis at the crystal scale has produced an unprecedented record of magmatic processes. However an obstacle to further progress is the lack of understanding of how mass, energy and momentum flux associated with crystal-rich, open-system events produces identifiable outcomes. Hence developing a physically-based understanding of magmatic systems linking micro-scale petrological observations with a physical template operating at the macro-scale presents a so-called "Grand Challenge." The essence of this challenge is that magmatic systems have characteristic length and feedback scales between those accessible by classical continuum and discrete methods. It has become increasingly obvious that the old-school continuum methods have limited resolution and power of explanation for multiphase (real) magma dynamics. This is, in part, because in crystal-rich systems the deformation is non-affine, and so the concept of constitutive behavior is less applicable and likely not even relevant, especially if one is interested in the emergent character of micro-scale processes. One expression of this is the cottage industry of proposing viscosity laws for magmas, which serves as "blunt force" de facto corrections for what is intrinsically multiphase behavior. Even in more fluid-rich systems many of these laws are not suitable for use in the very transport theories they aim to support. The alternative approach is the discrete method, where multiphase interactions are explicitly resolved. This is a daunting prospect given the numbers of crystals in magmas. But perhaps all crystals don't need to be modeled. I will demonstrate how discrete methods can recover critical state behavior, resolve crystal migration, the onset of visco-elastic behavior such as melt-present shear bands which sets the large-scale mixing volumes, some of the general morpho-dynamics that underlies purported rheological models, and transient controls on

  11. Multiphase inverse modeling: An Overview

    SciTech Connect

    Finsterle, S.

    1998-03-01

    Inverse modeling is a technique to derive model-related parameters from a variety of observations made on hydrogeologic systems, from small-scale laboratory experiments to field tests to long-term geothermal reservoir responses. If properly chosen, these observations contain information about the system behavior that is relevant to the performance of a geothermal field. Estimating model-related parameters and reducing their uncertainty is an important step in model development, because errors in the parameters constitute a major source of prediction errors. This paper contains an overview of inverse modeling applications using the ITOUGH2 code, demonstrating the possibilities and limitations of a formalized approach to the parameter estimation problem.

  12. An experimental investigation of the multiphase flows in a photobioreactor for algae cultivation

    NASA Astrophysics Data System (ADS)

    Yang, Zifeng; Hu, Hui; Del Ninno, Matteo; Wen, Zhiyou

    2011-11-01

    Algal biomass is a promising feedstock for biofuels production, with photobioreactors being one of the major cultivation systems for algal cells. Light absorption, fluid dynamics, and algal metabolism are three key factors in determining the overall performance of a photobioreactor. The behavior of the multiphase flow (i.e., liquid phase - water, gas phase - CO2 and O2, and solid phase - algal cells) and turbulent mixing inside the reactor are the core connecting the three factors together. One of the major challenges in the optimal design of photobioreactors for algae cultivation is the lack of in-depth understanding of the characteristics of the multiphase flows and turbulent mixing. In this study, we present a comprehensive experimental study to investigate the effects of turbulent mixing in photobioreactors on the performance of a photobioreactor for algae cultivation. A high-resolution particle image velocity (PIV) system is used to achieve time-resolved, in-situ flow field measurements to quantify the turbulent mixing of the multiphase flows inside the bioreactor, while algal cultures are also grown in the same reactor with the same experimental settings. The mixing characteristics of the multiphase flow are correlated with the algal growth performance in the bioreactors to elucidate the underlying physics to explore/optimize design paradigms for the optimization of photobioreactor designs for algae cultivation.

  13. Multiphase-Multifunctional Ceramic Coatings

    DTIC Science & Technology

    2013-06-30

    were conducted at 1200-1600° C from 10-24 h. Densification of powders in the pyrochlore-fuorite system was also performed by Spark Plasma Sintering ...capability with emphasis on improving toughness and phase stability. The primary goal was clearly accomplished by developing an instrumented air plasma ...composition. Coating compositions were synthesized by atmospheric plasma spray (APS) at CINVESTAV facilities, and dense monolithic counterparts were

  14. Comparison of tropospheric NO2 columns from ground based MAX-DOAS systems with satellite retrievals: A case study in the greater area of Thessaloniki.

    NASA Astrophysics Data System (ADS)

    Drosoglou, Theano; Bais, Alkis; Kouremeti, Natalia; Koukouli, Mariliza; Balis, Dimitris

    2015-04-01

    Phaethon is a low-cost ground-based MAX-DOAS system that is used to acquire fast direct solar irradiance and sky radiance spectrally resolved measurements in the region 300-450 nm and deliver total and tropospheric columns of atmospheric trace gases. Phaethon, which comprises a cooled miniature CCD spectrograph (AvaSpec-ULS2048LTEC) and a 2-axes tracker, was designed for easy deployment at different sites to address specific air quality problems and to support satellite validation studies at locations of particular scientific interest. In the framework of the Optimization and expansion of ground infrastructure for the validation of satellite-derived column densities of atmospheric species, AVANTI project, three Phaethon systems have been deployed in the greater area of Thessaloniki, Greece, within an area of about 15 km by 30 km, comparable to the size of a satellite pixel, with the aim to link modeling of tropospheric trace gases with satellite products. The locations of the three systems are characterized by diverse local atmospheric pollution loadings representing urban, industrial and rural conditions. The systems have been first operated for a few days in parallel at the station in the University campus to establish their inter-comparison behaviour and possible systematic differences. Tropospheric NO2 columns derived at these different locations are presented and compared with the "area-averaged" columns derived from OMI/Aura and GOME-2/MetopA and /MetopB satellites. During days with high levels of NO2 at the urban site, the measurements at the rural site compare better with the satellite products. This finding has been attributed to the fact that the satellite products are representative of the average pollution levels in the sub-satellite pixel area which, in the case of Thessaloniki, corresponds mostly to rural conditions. This validation campaign precedes a full-scale validation to be performed within the EU FP7 Monitoring and Assessment of Regional air

  15. Detection biomarkers of lung cancer using mini-GC-PID system integrated with micro GC column and micro pre-concentrator.

    PubMed

    Sun, Jianhai; Cui, Dafu; Guan, Fengying; Zhang, Lulu; Chen, Xing; Li, Hui

    2014-01-01

    The survival rate of lung cancer can be significantly improved by monitoring biomarkers in exhaled air that indicate diseases in early stage, so it is very important to develop micro analytical systems which can offer a fast, on-site, real-time detecting biomarkers in exhaled air. In this paper, a mini-gas chromatography (GC)-photo-ionization detector (PID) system integrated with a micro GC column and a micro pre-concentrator was developed for forming an inexpensive, fast, and non-invasive diagnostic tool for lung cancer. This system has very strong concentrate ability owing to its integrated micro pre-concentrator, which make the detection of trace components in exhaled air very easy. In addition, the integrated micro GC column can separate complex mixtures, which overcome low resolution and poor anti-interference ability of other instruments. The results indicated that the mini-GC-PID system can effectively separate and detect the biomarkers at parts-per-billion (ppb) level.

  16. Multiphase design of autonomic self-healing thermoplastic elastomers

    NASA Astrophysics Data System (ADS)

    Chen, Yulin; Kushner, Aaron M.; Williams, Gregory A.; Guan, Zhibin

    2012-06-01

    The development of polymers that can spontaneously repair themselves after mechanical damage would significantly improve the safety, lifetime, energy efficiency and environmental impact of man-made materials. Most approaches to self-healing materials require the input of external energy, healing agents, solvent or plasticizer. Despite intense research in this area, the synthesis of a stiff material with intrinsic self-healing ability remains a key challenge. Here, we show a design of multiphase supramolecular thermoplastic elastomers that combine high modulus and toughness with spontaneous healing capability. The designed hydrogen-bonding brush polymers self-assemble into a hard-soft microphase-separated system, combining the enhanced stiffness and toughness of nanocomposites with the self-healing capability of dynamic supramolecular assemblies. In contrast to previous self-healing polymers, this new system spontaneously self-heals as a single-component solid material at ambient conditions, without the need for any external stimulus, healing agent, plasticizer or solvent.

  17. Preferential Mode of gas invasion in sediments: Grain-scale mechanistic model of coupled multiphase fluid flow and sediment mechanics

    NASA Astrophysics Data System (ADS)

    Jain, A. K.; Juanes, R.

    2009-08-01

    We present a discrete element model for simulating, at the grain scale, gas migration in brine-saturated deformable media. We rigorously account for the presence of two fluids in the pore space by incorporating forces on grains due to pore fluid pressures and surface tension between fluids. This model, which couples multiphase fluid flow with sediment mechanics, permits investigation of the upward migration of gas through a brine-filled sediment column. We elucidate the ways in which gas migration may take place: (1) by capillary invasion in a rigid-like medium and (2) by initiation and propagation of a fracture. We find that grain size is the main factor controlling the mode of gas transport in the sediment, and we show that coarse-grain sediments favor capillary invasion, whereas fracturing dominates in fine-grain media. The results have important implications for understanding vent sites and pockmarks in the ocean floor, deep subseabed storage of carbon dioxide, and gas hydrate accumulations in ocean sediments and permafrost regions. Our results predict that in fine sediments, hydrate will likely form in veins following a fracture network pattern, and the hydrate concentration will likely be quite low. In coarse sediments, the buoyant methane gas is likely to invade the pore space more uniformly, in a process akin to invasion percolation, and the overall pore occupancy is likely to be much higher than for a fracture-dominated regime. These implications are consistent with laboratory experiments and field observations of methane hydrates in natural systems.

  18. Multiphase flow and phase change in microgravity: Fundamental research and strategic research for exploration of space

    NASA Technical Reports Server (NTRS)

    Singh, Bhim S.

    2003-01-01

    NASA is preparing to undertake science-driven exploration missions. The NASA Exploration Team's vision is a cascade of stepping stones. The stepping-stone will build the technical capabilities needed for each step with multi-use technologies and capabilities. An Agency-wide technology investment and development program is necessary to implement the vision. The NASA Exploration Team has identified a number of areas where significant advances are needed to overcome all engineering and medical barriers to the expansion of human space exploration beyond low-Earth orbit. Closed-loop life support systems and advanced propulsion and power technologies are among the areas requiring significant advances from the current state-of-the-art. Studies conducted by the National Academy of Science's National Research Council and Workshops organized by NASA have shown that multiphase flow and phase change play a crucial role in many of these advanced technology concepts. Lack of understanding of multiphase flow, phase change, and interfacial phenomena in the microgravity environment has been a major hurdle. An understanding of multiphase flow and phase change in microgravity is, therefore, critical to advancing many technologies needed. Recognizing this, the Office of Biological and Physical Research (OBPR) has initiated a strategic research thrust to augment the ongoing fundamental research in fluid physics and transport phenomena discipline with research especially aimed at understanding key multiphase flow related issues in propulsion, power, thermal control, and closed-loop advanced life support systems. A plan for integrated theoretical and experimental research that has the highest probability of providing data, predictive tools, and models needed by the systems developers to incorporate highly promising multiphase-based technologies is currently in preparation. This plan is being developed with inputs from scientific community, NASA mission planners and industry personnel

  19. Inelastic column behavior

    NASA Technical Reports Server (NTRS)

    Duberg, John E; Wilder, Thomas W , III

    1952-01-01

    The significant findings of a theoretical study of column behavior in the plastic stress range are presented. When the behavior of a straight column is regarded as the limiting behavior of an imperfect column as the initial imperfection (lack of straightness) approaches zero, the departure from the straight configuration occurs at the tangent-modulus load. Without such a concept of the behavior of a straight column, one is led to the unrealistic conclusion that lateral deflection of the column can begin at any load between the tangent-modulus value and the Euler load, based on the original elastic modulus. A family of curves showing load against lateral deflection is presented for idealized h-section columns of various lengths and of various materials that have a systematic variation of their stress-strain curves.

  20. Automated design of multiphase space missions using hybrid optimal control

    NASA Astrophysics Data System (ADS)

    Chilan, Christian Miguel

    A modern space mission is assembled from multiple phases or events such as impulsive maneuvers, coast arcs, thrust arcs and planetary flybys. Traditionally, a mission planner would resort to intuition and experience to develop a sequence of events for the multiphase mission and to find the space trajectory that minimizes propellant use by solving the associated continuous optimal control problem. This strategy, however, will most likely yield a sub-optimal solution, as the problem is sophisticated for several reasons. For example, the number of events in the optimal mission structure is not known a priori and the system equations of motion change depending on what event is current. In this work a framework for the automated design of multiphase space missions is presented using hybrid optimal control (HOC). The method developed uses two nested loops: an outer-loop that handles the discrete dynamics and finds the optimal mission structure in terms of the categorical variables, and an inner-loop that performs the optimization of the corresponding continuous-time dynamical system and obtains the required control history. Genetic algorithms (GA) and direct transcription with nonlinear programming (NLP) are introduced as methods of solution for the outer-loop and inner-loop problems, respectively. Automation of the inner-loop, continuous optimal control problem solver, required two new technologies. The first is a method for the automated construction of the NLP problems resulting from the use of a direct solver for systems with different structures, including different numbers of categorical events. The method assembles modules, consisting of parameters and constraints appropriate to each event, sequentially according to the given mission structure. The other new technology is for a robust initial guess generator required by the inner-loop NLP problem solver. Two new methods were developed for cases including low-thrust trajectories. The first method, based on GA

  1. Airlift column photobioreactors for Porphyridium sp. culturing: part I. effects of hydrodynamics and reactor geometry.

    PubMed

    Luo, Hu-Ping; Al-Dahhan, Muthanna H

    2012-04-01

    Photosynthetic microorganisms have been attracting world attention for their great potential as renewable energy sources in recent years. Cost effective production in large scale, however, remains a major challenge to overcome. It is known to the field that turbulence could help improving the performance of photobioreactors due to the so-called flashing light effects. Better understanding of the multiphase fluid dynamics and the irradiance distribution inside the reactor that cause the flashing light effects, as well as quantifying their impacts on the reactor performance, thus, are crucial for successful design and scale-up of photobioreactors. In this study, a species of red marine microalgae, Porphyridium sp., was grown in three airlift column photobioreactors (i.e., draft tube column, bubble column, and split column). The physical properties of the culture medium, the local fluid dynamics and the photobioreactor performances were investigated and are reported in this part of the manuscript. Results indicate that the presence of microalgae considerably affected the local multiphase flow dynamics in the studied draft tube column. Results also show that the split column reactor works slightly better than the draft tube and the bubble columns due to the spiral flow pattern inside the reactor.

  2. Inhibition of microbial sulfate reduction in a flow-through column system by (per)chlorate treatment.

    PubMed

    Engelbrektson, Anna; Hubbard, Christopher G; Tom, Lauren M; Boussina, Aaron; Jin, Yong T; Wong, Hayden; Piceno, Yvette M; Carlson, Hans K; Conrad, Mark E; Anderson, Gary; Coates, John D

    2014-01-01

    Microbial sulfate reduction is a primary cause of oil reservoir souring. Here we show that amendment with chlorate or perchlorate [collectively (per)chlorate] potentially resolves this issue. Triplicate packed columns inoculated with marine sediment were flushed with coastal water amended with yeast extract and one of nitrate, chlorate, or perchlorate. Results showed that although sulfide production was dramatically reduced by all treatments, effluent sulfide was observed in the nitrate (10 mM) treatment after an initial inhibition period. In contrast, no effluent sulfide was observed with (per)chlorate (10 mM). Microbial community analyses indicated temporal community shifts and phylogenetic clustering by treatment. Nitrate addition stimulated Xanthomonadaceae and Rhizobiaceae growth, supporting their role in nitrate metabolism. (Per)chlorate showed distinct effects on microbial community structure compared with nitrate and resulted in a general suppression of the community relative to the untreated control combined with a significant decrease in sulfate reducing species abundance indicating specific toxicity. Furthermore, chlorate stimulated Pseudomonadaceae and Pseudoalteromonadaceae, members of which are known chlorate respirers, suggesting that chlorate may also control sulfidogenesis by biocompetitive exclusion of sulfate-reduction. Perchlorate addition stimulated Desulfobulbaceae and Desulfomonadaceae, which contain sulfide oxidizing and elemental sulfur-reducing species respectively, suggesting that effluent sulfide concentrations may be controlled through sulfur redox cycling in addition to toxicity and biocompetitive exclusion. Sulfur isotope analyses further support sulfur cycling in the columns, even when sulfide is not detected. This study indicates that (per)chlorate show great promise as inhibitors of sulfidogenesis in natural communities and provides insight into which organisms and respiratory processes are involved.

  3. Inhibition of microbial sulfate reduction in a flow-through column system by (per)chlorate treatment

    PubMed Central

    Engelbrektson, Anna; Hubbard, Christopher G.; Tom, Lauren M.; Boussina, Aaron; Jin, Yong T.; Wong, Hayden; Piceno, Yvette M.; Carlson, Hans K.; Conrad, Mark E.; Anderson, Gary; Coates, John D.

    2014-01-01

    Microbial sulfate reduction is a primary cause of oil reservoir souring. Here we show that amendment with chlorate or perchlorate [collectively (per)chlorate] potentially resolves this issue. Triplicate packed columns inoculated with marine sediment were flushed with coastal water amended with yeast extract and one of nitrate, chlorate, or perchlorate. Results showed that although sulfide production was dramatically reduced by all treatments, effluent sulfide was observed in the nitrate (10 mM) treatment after an initial inhibition period. In contrast, no effluent sulfide was observed with (per)chlorate (10 mM). Microbial community analyses indicated temporal community shifts and phylogenetic clustering by treatment. Nitrate addition stimulated Xanthomonadaceae and Rhizobiaceae growth, supporting their role in nitrate metabolism. (Per)chlorate showed distinct effects on microbial community structure compared with nitrate and resulted in a general suppression of the community relative to the untreated control combined with a significant decrease in sulfate reducing species abundance indicating specific toxicity. Furthermore, chlorate stimulated Pseudomonadaceae and Pseudoalteromonadaceae, members of which are known chlorate respirers, suggesting that chlorate may also control sulfidogenesis by biocompetitive exclusion of sulfate-reduction. Perchlorate addition stimulated Desulfobulbaceae and Desulfomonadaceae, which contain sulfide oxidizing and elemental sulfur-reducing species respectively, suggesting that effluent sulfide concentrations may be controlled through sulfur redox cycling in addition to toxicity and biocompetitive exclusion. Sulfur isotope analyses further support sulfur cycling in the columns, even when sulfide is not detected. This study indicates that (per)chlorate show great promise as inhibitors of sulfidogenesis in natural communities and provides insight into which organisms and respiratory processes are involved. PMID:25071731

  4. Distillation Column Modeling Tools

    SciTech Connect

    2001-09-01

    Advanced Computational and Experimental Techniques will Optimize Distillation Column Operation. Distillation is a low thermal efficiency unit operation that currently consumes 4.8 quadrillion BTUs of energy...

  5. Strong piezoelectricity in (1 - x)(K0.4Na0.6)(Nb0.96Sb0.04)O3-xBi0.5K0.5Zr1-ySnyO3 lead-free binary system: identification and role of multiphase coexistence.

    PubMed

    Zheng, Ting; Wu, Jiagang; Xiao, Dingquan; Zhu, Jianguo; Wang, Xiangjian; Xin, Lipeng; Lou, Xiaojie

    2015-03-18

    Here we report a strong piezoelectric activity in (1 - x)(K0.4Na0.6)(Nb0.96Sb0.04)O3-xBi0.5K0.5Zr1-ySnyO3 lead-free ceramics by designing different phase boundaries. The phase boundaries concerning rhombohedral-orthorhombic-tetragonal (R-O-T) and rhombohedral-tetragonal (R-T) multiphase coexistence were attained by changing BKZS and Sn contents and then were identified by the X-ray diffraction patterns as well as temperature-dependent permittivity and ν1 Raman modes associated with BO6 perovskite octahedron. A high strain (strain = 0.21-0.28% and d33* = 707-880 pm/V) and a strong piezoelectric coefficient (d33 = 415-460 pC/N) were shown in the ceramics located at the multiphase coexistence region. The reported results of this work are superior to that (d33* ∼ 570 pm/V and d33 ∼ 416 pC/N) of the textured (K,Na,Li)(Nb,Ta,Sb)O3 ceramics [Nature 2004, 432, 84]. We believe that the material system of this work will become one of the most promising candidates for piezoelectric actuators.

  6. Thermophysical Properties of Multiphase Borosilicate Glass-Ceramic Waste Forms

    SciTech Connect

    Nelson, Andrew T.; Crum, Jarrod V.; Tang, Ming; Rouxel, T.

    2014-01-22

    Multiphase borosilicate glass-ceramics represent one candidate to contain radioactive nuclear waste separated from used nuclear fuel. In this work, the thermophysical properties from room temperature to 1273 K were investigated for four different borosilicate glass-ceramic compositions containing waste loadings from 42 to 60 wt% to determine the sensitivity of these properties to waste loading, as-fabricated microstructure, and potential evolutions in microstructure brought about by temperature transients. The thermal expansion, specific heat capacity, thermal diffusivity, and thermal conductivity are presented. The impact of increasing waste loading is shown to have a small but measurable effect on the thermophysical properties between the four compositions, contrasted to a much greater impact observed when transitioning from predominantly crystalline to amorphous systems. Thermal cycling below 1273 K was not found to measurably impact the thermophysical properties of the compositions investigated here.

  7. Temperature effects on the electrical properties of multiphase polymer composites

    NASA Astrophysics Data System (ADS)

    De Vivo, Biagio; Guadagno, Liberata; Lamberti, Patrizia; Raimondo, Marialuigia; Spinelli, Giovanni; Tucci, Vincenzo; Vertuccio, Luigi; Vittoria, Vittoria

    2014-05-01

    A study concerning the temperature dependence of some electrical properties of multiphase nanocomposite systems based on epoxy matrix, loaded with a 1% of multi-walled carbon nanotube (MWCNT) and different amounts of Hydrotalcite clay (HT), is presented. An extensive electrical characterization in DC was carried out highlighting that, consistently with the fluctuation-induced tunneling model, the electrical resistivity of the composites are characterized by a negative temperature coefficient (NTC) since it decreases monotonically with increasing temperature in the range 30-110°C. Furthermore, current-voltage (I-V) and temperature-voltage (T-V) characteristics with a perfect linear behavior are detected. The influence of different clay content on the electrical performance of the composites is also investigated. The interesting results open a new routes for such composites due their possible applications in the field of temperature sensor.

  8. Oscillatory multiphase flow strategy for chemistry and biology.

    PubMed

    Abolhasani, Milad; Jensen, Klavs F

    2016-07-19

    Continuous multiphase flow strategies are commonly employed for high-throughput parameter screening of physical, chemical, and biological processes as well as continuous preparation of a wide range of fine chemicals and micro/nano particles with processing times up to 10 min. The inter-dependency of mixing and residence times, and their direct correlation with reactor length have limited the adaptation of multiphase flow strategies for studies of processes with relatively long processing times (0.5-24 h). In this frontier article, we describe an oscillatory multiphase flow strategy to decouple mixing and residence times and enable investigation of longer timescale experiments than typically feasible with conventional continuous multiphase flow approaches. We review current oscillatory multiphase flow technologies, provide an overview of the advancements of this relatively new strategy in chemistry and biology, and close with a perspective on future opportunities.

  9. Column flotation '88

    SciTech Connect

    Sastry, K.V.S.

    1988-01-01

    This book contains 34 selections. Some of the titles are: Column flotation of ultrafine coal: experience at BHP-Utah Coal Limited's Riverside mine; Measurement of rate data in flotation columns; Factors influencing the structure of a 3-phase coal flotation froth; and Microbubble flotation of fine coal.

  10. Inflatable Column Structure

    NASA Technical Reports Server (NTRS)

    Hedgepeth, J. M.

    1985-01-01

    Lightweight structural member easy to store. Billowing between circumferential loops of fiber inflated column becomes series of cells. Each fiber subjected to same tension along entire length (though tension is different in different fibers). Member is called "isotensoid" column. Serves as jack for automobiles or structures during repairs. Also used as support for temporary bleachers or swimming pools.

  11. Multiphase equation of state for iron

    SciTech Connect

    Kerley, G I

    1993-02-01

    The PANDA code is used to build a multiphase equation of state (EOS) table for iron. Separate EOS tables were first constructed for each of the individual phases. The phase diagram and multiphase EOS were then determined from the Helmholtz free energies. The model includes four solid phases ([alpha],[gamma], [delta], and [var epsilon]) and a fluid phase (including the liquid, vapor, and supercritical regions). The model gives good agreement with experimental thermophysical data, static compression data, phase boundaries, and shock-wave measurements. Contributions from thermal electronic excitation, computed from a quantum-statistical-mechanical model, were found to be very important. This EOS covers a wide range of densities (0--1000 g/cm[sup 3]) and temperatures (0--1.2[times]10[sup 7] K). It is also applicable to RHA steel. The new EOS is used in hydrocode simulations of plate impact experiments, a nylon ball impact on steel, and the shaped charge perforation of an RHA plate. The new EOS table can be accessed through the SNL-SESAME library as material number 2150.

  12. Multiphasic Scaffolds for Periodontal Tissue Engineering

    PubMed Central

    Ivanovski, S.; Vaquette, C.; Gronthos, S.; Hutmacher, D.W.; Bartold, P.M.

    2014-01-01

    For a successful clinical outcome, periodontal regeneration requires the coordinated response of multiple soft and hard tissues (periodontal ligament, gingiva, cementum, and bone) during the wound-healing process. Tissue-engineered constructs for regeneration of the periodontium must be of a complex 3-dimensional shape and adequate size and demonstrate biomechanical stability over time. A critical requirement is the ability to promote the formation of functional periodontal attachment between regenerated alveolar bone, and newly formed cementum on the root surface. This review outlines the current advances in multiphasic scaffold fabrication and how these scaffolds can be combined with cell- and growth factor–based approaches to form tissue-engineered constructs capable of recapitulating the complex temporal and spatial wound-healing events that will lead to predictable periodontal regeneration. This can be achieved through a variety of approaches, with promising strategies characterized by the use of scaffolds that can deliver and stabilize cells capable of cementogenesis onto the root surface, provide biomechanical cues that encourage perpendicular alignment of periodontal fibers to the root surface, and provide osteogenic cues and appropriate space to facilitate bone regeneration. Progress on the development of multiphasic constructs for periodontal tissue engineering is in the early stages of development, and these constructs need to be tested in large animal models and, ultimately, human clinical trials. PMID:25139362

  13. Multiphasic scaffolds for periodontal tissue engineering.

    PubMed

    Ivanovski, S; Vaquette, C; Gronthos, S; Hutmacher, D W; Bartold, P M

    2014-12-01

    For a successful clinical outcome, periodontal regeneration requires the coordinated response of multiple soft and hard tissues (periodontal ligament, gingiva, cementum, and bone) during the wound-healing process. Tissue-engineered constructs for regeneration of the periodontium must be of a complex 3-dimensional shape and adequate size and demonstrate biomechanical stability over time. A critical requirement is the ability to promote the formation of functional periodontal attachment between regenerated alveolar bone, and newly formed cementum on the root surface. This review outlines the current advances in multiphasic scaffold fabrication and how these scaffolds can be combined with cell- and growth factor-based approaches to form tissue-engineered constructs capable of recapitulating the complex temporal and spatial wound-healing events that will lead to predictable periodontal regeneration. This can be achieved through a variety of approaches, with promising strategies characterized by the use of scaffolds that can deliver and stabilize cells capable of cementogenesis onto the root surface, provide biomechanical cues that encourage perpendicular alignment of periodontal fibers to the root surface, and provide osteogenic cues and appropriate space to facilitate bone regeneration. Progress on the development of multiphasic constructs for periodontal tissue engineering is in the early stages of development, and these constructs need to be tested in large animal models and, ultimately, human clinical trials.

  14. Multiphase rotodynamic pumps extend their operating capabilities

    SciTech Connect

    Falcimaigne, J.; Durando, P.; Loupias, M.; Vilagines, R.

    1994-12-31

    The paper describes the main features of the P302 multiphase pump and presents some results of bench tests carried out to check its hydraulic performances. The P302 is a rotodynamic helico-axial pump based on the Poseidon pumping technology. It is equipped with water lubricated bearings and driven by a high speed electrical motor. The pump was designed to work with a suction pressure much lower than the P300 prototype and to deliver a higher compression ratio. It has fifteen stages of compression cells, in three different series. Before installing the pump on an onshore production site for endurance tests with actual field fluids, the steady-state behavior and the transient responses of the pump were characterized on the IFP multiphase loop at Solaize (France). The pump was tested both with single phase fluids (liquid or gas) and a diphasic mixture (fuel-oil and nitrogen) at various GVF and suction pressures. In the paper, theoretical predictions are compared to measured data. The good results of these tests confirmed the soundness and versatility of the Poseidon hydraulics and also the calculation model ability to predict accurately the performances of rotodynamic pump over a wide range of operating conditions.

  15. MULTI-PHASE FRACTURE-MATRIX INTERACTIONS UNDER STRESS CHANGES

    SciTech Connect

    A.S. Grader; D. Elsworth; P.M. Halleck; F. Alvarado; A. Alajmi; Z. Karpyn; N. Mohammed; S. Al-Enezi

    2005-06-15

    The main objectives of this project are to quantify the changes in fracture porosity and multiphase transport properties as a function of confining stress. These changes will be integrated into conceptual and numerical models that will improve our ability to predict and optimize fluid transport in fractured system. This report details our progress on: (a) developing the direct experimental measurements of fracture aperture and topology and fluid occupancy using high-resolution x-ray micro-tomography, (b) quantifying the effect of confining stress on the distribution of fracture aperture, and (c) characterization of shear fractures and their impact on multi-phase flow. The three-dimensional surface that describes the large-scale structure of the fracture in the porous medium can be determined using x-ray micro-tomography with significant accuracy. Several fractures have been scanned and the fracture aperture maps have been extracted. The success of the mapping of fracture aperture was followed by measuring the occupancy of the fracture by two immiscible phases, water and decane, and water and kerosene. The distribution of fracture aperture depends on the effective confining stress on the nature of the rock and the type and distribution of the asperities that keep the fracture open. Fracture apertures at different confining stresses were obtained by micro-tomography covering a range of about two thousand psig. Initial analysis of the data shows a significant aperture closure with increase in effective confining stress. Visual descriptions of the process are shown in the report while detailed analysis of the behavior of the distribution of fracture aperture is in progress. Both extensional and shear fractures are being considered. The initial multi-phase flow tests were done in extensional fractures. Several rock samples with induced shear fracture are being studied, and some of the new results are presented in this report. These samples are being scanned in order to

  16. MULTI-PHASE FRACTURE-MATRIX INTERACTIONS UNDER STRESS CHANGES

    SciTech Connect

    A.S. Grader; D. Elsworth; P.M. Halleck; F. Alvarado; A. Alajmi; Z. Karpyn; N. Mohammed; S. Al-Enezi

    2005-06-15

    The main objectives of this project are to quantify the changes in fracture porosity and multiphase transport properties as a function of confining stress. These changes will be integrated into conceptual and numerical models that will improve our ability to predict and optimize fluid transport in fractured system. This report details our progress on: (a) developing the direct experimental measurements of fracture aperture and topology and fluid occupancy using high-resolution x-ray micro-tomography, (b) quantifying the effect of confining stress on the distribution of fracture aperture, and (c) characterization of shear fractures and their impact on multi-phase flow. The three-dimensional surface that describes the large-scale structure of the fracture in the porous medium can be determined using x-ray micro-tomography with significant accuracy. Several fractures have been scanned and the fracture aperture maps have been extracted. The success of the mapping of fracture aperture was followed by measuring the occupancy of the fracture by two immiscible phases, water and decane, and water and kerosene. The distribution of fracture aperture depends on the effective confining stress on the nature of the rock and the type and distribution of the asperities that keep the fracture open. Fracture apertures at different confining stresses were obtained by micro-tomography covering a range of about two thousand psig. Initial analysis of the data shows a significant aperture closure with increase in effective confining stress. Visual descriptions of the process are shown in the report while detailed analysis of the behavior of the distribution of fracture aperture is in progress. Both extensional and shear fractures are being considered. The initial multi-phase flow tests were done in extensional fractures. Several rock samples with induced shear fracture are being studies, and some of the new results are presented in this report. These samples are being scanned in order to

  17. Breakthrough studies with mono-, binary- and ternary-ion systems comprised of Fe(II), F(-) and As(III) using river sand packed columns for groundwater treatment.

    PubMed

    Ahamad, Kamal Uddin; Jawed, Mohammad

    2013-06-01

    Groundwater in Assam, India, contains excessive amounts of arsenic (As(III)), fluoride (F(-)) and iron (Fe(II)). The rural and semi-urban population of Assam uses indigenous iron filters fabricated using processed sand (PS) as one of the chief constituents to reduce Fe(II) concentration; however, no efforts have been made to reduce As(III) or F(-) concentrations before use. The present work is directed towards assessing the potential of PS for removal of these ions from mono-, binary- and ternary-ion systems through continuous mode column studies. Synthetic water samples containing fixed concentration of ions were prepared using deionized water. The observed order of breakthrough of ions was: As(III) followed by Fe(II) and F(-) followed by Fe(II) in the case of the binary ion systems of Fe(II) + As(III) and Fe(II) + F(-). The throughput volume for As(III) in the (Fe(II) + As(III)) system and for F(-) in the (Fe(II) + F(-)) system is termed the critical breakthrough throughput volume. In the ternary ion system (Fe(II) + As(III) + F(-)), the order of breakthrough of ions observed was F(-), then As(III) and then Fe(II) and hence the throughput volume F(-) is termed the critical breakthrough throughput volume. Results of column studies also indicate the impact on the uptake of the selected ion by the presence of the other ion present in the binary- and ternary-ion systems.

  18. Isothermal Multiphase Flash Calculations with the PC-SAFT Equation of State

    SciTech Connect

    Justo-Garcia, Daimler N.; Garcia-Sanchez, Fernando; Romero-Martinez, Ascencion

    2008-03-05

    A computational approach for isothermal multiphase flash calculations with the PC-SAFT (Perturbed-Chain Statistical Associating Fluid Theory) equation of state is presented. In the framework of the study of fluid phase equilibria of multicomponent systems, the general multiphase problem is the single most important calculation which consists of finding the correct number and types of phases and their corresponding equilibrium compositions such that the Gibbs energy of the system is a minimum. For solving this problem, the system Gibbs energy was minimized using a rigorous method for thermodynamic stability analysis to find the most stable state of the system. The efficiency and reliability of the approach to predict and calculate complex phase equilibria are illustrated by solving three typical problems encountered in the petroleum industry.

  19. Modeling of column flotation

    SciTech Connect

    Luttrell, G.H.; Adel, G.T.; Yoon, R.H.

    1987-01-01

    Many investigators believe that column flotation cells offer significant advantages over standard mechanical machines for the flotation of fine particles. However, because of their unique design and operation, conventional techniques for flotation cell scale-up and design cannot be applied to columns. In an attempt to help alleviate this problem, a population balance model based on first principles has been developed for fine particle flotation in a column. Two different terms have been considered in the model, i.e., transport and rate. Transport terms, incorporating fluid flow and buoyancy, are used to describe the movement of air bubbles, unattached particles and bubble-particle aggregates along the length of the column. Rate terms, which describe the bubble-particle attachment process, have been derived from first principle considerations. Because the model is based on first principles, it can be useful for the design, control, optimization and scale-up of column flotation cells. 9 refs., 12 figs.

  20. Glass-silicon column

    DOEpatents

    Yu, Conrad M.

    2003-12-30

    A glass-silicon column that can operate in temperature variations between room temperature and about 450.degree. C. The glass-silicon column includes large area glass, such as a thin Corning 7740 boron-silicate glass bonded to a silicon wafer, with an electrode embedded in or mounted on glass of the column, and with a self alignment silicon post/glass hole structure. The glass/silicon components are bonded, for example be anodic bonding. In one embodiment, the column includes two outer layers of silicon each bonded to an inner layer of glass, with an electrode imbedded between the layers of glass, and with at least one self alignment hole and post arrangement. The electrode functions as a column heater, and one glass/silicon component is provided with a number of flow channels adjacent the bonded surfaces.

  1. JCE Feature Columns

    NASA Astrophysics Data System (ADS)

    Holmes, Jon L.

    1999-05-01

    The Features area of JCE Online is now readily accessible through a single click from our home page. In the Features area each column is linked to its own home page. These column home pages also have links to them from the online Journal Table of Contents pages or from any article published as part of that feature column. Using these links you can easily find abstracts of additional articles that are related by topic. Of course, JCE Online+ subscribers are then just one click away from the entire article. Finding related articles is easy because each feature column "site" contains links to the online abstracts of all the articles that have appeared in the column. In addition, you can find the mission statement for the column and the email link to the column editor that I mentioned above. At the discretion of its editor, a feature column site may contain additional resources. As an example, the Chemical Information Instructor column edited by Arleen Somerville will have a periodically updated bibliography of resources for teaching and using chemical information. Due to the increase in the number of these resources available on the WWW, it only makes sense to publish this information online so that you can get to these resources with a simple click of the mouse. We expect that there will soon be additional information and resources at several other feature column sites. Following in the footsteps of the Chemical Information Instructor, up-to-date bibliographies and links to related online resources can be made available. We hope to extend the online component of our feature columns with moderated online discussion forums. If you have a suggestion for an online resource you would like to see included, let the feature editor or JCE Online (jceonline@chem.wisc.edu) know about it. JCE Internet Features JCE Internet also has several feature columns: Chemical Education Resource Shelf, Conceptual Questions and Challenge Problems, Equipment Buyers Guide, Hal's Picks, Mathcad

  2. The Theory of Localist Representation and of a Purely Abstract Cognitive System: The Evidence from Cortical Columns, Category Cells, and Multisensory Neurons.

    PubMed

    Roy, Asim

    2017-01-01

    The debate about representation in the brain and the nature of the cognitive system has been going on for decades now. This paper examines the neurophysiological evidence, primarily from single cell recordings, to get a better perspective on both the issues. After an initial review of some basic concepts, the paper reviews the data from single cell recordings - in cortical columns and of category-selective and multisensory neurons. In neuroscience, columns in the neocortex (cortical columns) are understood to be a basic functional/computational unit. The paper reviews the fundamental discoveries about the columnar organization and finds that it reveals a massively parallel search mechanism. This columnar organization could be the most extensive neurophysiological evidence for the widespread use of localist representation in the brain. The paper also reviews studies of category-selective cells. The evidence for category-selective cells reveals that localist representation is also used to encode complex abstract concepts at the highest levels of processing in the brain. A third major issue is the nature of the cognitive system in the brain and whether there is a form that is purely abstract and encoded by single cells. To provide evidence for a single-cell based purely abstract cognitive system, the paper reviews some of the findings related to multisensory cells. It appears that there is widespread usage of multisensory cells in the brain in the same areas where sensory processing takes place. Plus there is evidence for abstract modality invariant cells at higher levels of cortical processing. Overall, that reveals the existence of a purely abstract cognitive system in the brain. The paper also argues that since there is no evidence for dense distributed representation and since sparse representation is actually used to encode memories, there is actually no evidence for distributed representation in the brain. Overall, it appears that, at an abstract level, the

  3. The Theory of Localist Representation and of a Purely Abstract Cognitive System: The Evidence from Cortical Columns, Category Cells, and Multisensory Neurons

    PubMed Central

    Roy, Asim

    2017-01-01

    The debate about representation in the brain and the nature of the cognitive system has been going on for decades now. This paper examines the neurophysiological evidence, primarily from single cell recordings, to get a better perspective on both the issues. After an initial review of some basic concepts, the paper reviews the data from single cell recordings – in cortical columns and of category-selective and multisensory neurons. In neuroscience, columns in the neocortex (cortical columns) are understood to be a basic functional/computational unit. The paper reviews the fundamental discoveries about the columnar organization and finds that it reveals a massively parallel search mechanism. This columnar organization could be the most extensive neurophysiological evidence for the widespread use of localist representation in the brain. The paper also reviews studies of category-selective cells. The evidence for category-selective cells reveals that localist representation is also used to encode complex abstract concepts at the highest levels of processing in the brain. A third major issue is the nature of the cognitive system in the brain and whether there is a form that is purely abstract and encoded by single cells. To provide evidence for a single-cell based purely abstract cognitive system, the paper reviews some of the findings related to multisensory cells. It appears that there is widespread usage of multisensory cells in the brain in the same areas where sensory processing takes place. Plus there is evidence for abstract modality invariant cells at higher levels of cortical processing. Overall, that reveals the existence of a purely abstract cognitive system in the brain. The paper also argues that since there is no evidence for dense distributed representation and since sparse representation is actually used to encode memories, there is actually no evidence for distributed representation in the brain. Overall, it appears that, at an abstract level, the

  4. Simulating the 2012 High Plains Drought Using Three Single Column Model Versions of the Community Earth System Model (SCM-CESM)

    NASA Astrophysics Data System (ADS)

    Medina, I. D.; Denning, S.

    2014-12-01

    The impact of changes in the frequency and severity of drought on fresh water sustainability is a great concern for many regions of the world. One such location is the High Plains, where the local economy is primarily driven by fresh water withdrawals from the Ogallala Aquifer, which accounts for approximately 30% of total irrigation withdrawals from all U.S. aquifers combined. Modeling studies that focus on the feedback mechanisms that control the climate and eco-hydrology during times of drought are limited in the sense that they use conventional General Circulation Models (GCMs) with grid length scales ranging from one hundred to several hundred kilometers. Additionally, these models utilize crude statistical parameterizations of cloud processes for estimating sub-grid fluxes of heat and moisture and have a poor representation of land surface heterogeneity. For this research, we focus on the 2012 High Plains drought, and will perform numerical simulations using three single column model versions of the Community Earth System Model (SCM-CESM) at multiple sites overlying the Ogallala Aquifer for the 2010-2012 period. In the first version of SCM-CESM, CESM will be used in standard mode (Community Atmospheric Model (CAM) coupled to a single instance of the Community Land Model (CLM)), secondly, CESM will be used in Super-Parameterized mode (SP-CESM), where a cloud resolving model (CRM consists of 32 atmospheric columns) replaces the standard CAM atmospheric parameterization and is coupled to a single instance of CLM, and thirdly, CESM is used in "Multi Instance" SP-CESM mode, where an instance of CLM is coupled to each CRM column of SP-CESM (32 CRM columns coupled to 32 instances of CLM). To assess the physical realism of the land-atmosphere feedbacks simulated at each site by all versions of SCM-CESM, differences in simulated energy and moisture fluxes will be computed between years for the 2010-2012 period, and will be compared to differences calculated using

  5. An origin for multiphase gas in galactic winds and haloes

    NASA Astrophysics Data System (ADS)

    Thompson, Todd A.; Quataert, Eliot; Zhang, Dong; Weinberg, David H.

    2016-01-01

    The physical origin of high-velocity cool gas seen in galactic winds remains unknown. Following work by B. Wang, we argue that radiative cooling in initially hot thermally-driven outflows can produce fast neutral atomic and photoionized cool gas. The inevitability of adiabatic cooling from the flow's initial 107-108 K temperature and the shape of the cooling function for T ≲ 107 K imply that outflows with hot gas mass-loss rate relative to star formation rate of β =dot{M}_hot/dot{M}_star ≳ 0.5 cool radiatively on scales ranging from the size of the energy injection region to tens of kpc. We highlight the β and star formation rate surface density dependence of the column density, emission measure, radiative efficiency, and velocity. At rcool, the gas produces X-ray and then UV/optical line emission with a total power bounded by ˜10-2 L⋆ if the flow is powered by steady-state star formation with luminosity L⋆. The wind is thermally unstable at rcool, potentially leading to a multiphase medium. Cooled winds decelerate significantly in the extended gravitational potential of galaxies. The cool gas precipitated from hot outflows may explain its prevalence in galactic haloes. We forward a picture of winds whereby cool clouds are initially accelerated by the ram pressure of the hot flow, but are rapidly shredded by hydrodynamical instabilities, thereby increasing β, seeding radiative and thermal instability, and cool gas rebirth. If the cooled wind shocks as it sweeps up the circumgalactic medium, its cooling time is short, thus depositing cool gas far out into the halo. Finally, conduction can dominate energy transport in low-β hot winds, leading to flatter temperature profiles than otherwise expected, potentially consistent with X-ray observations of some starbursts.

  6. Nuclear reactor control column

    DOEpatents

    Bachovchin, Dennis M.

    1982-01-01

    The nuclear reactor control column comprises a column disposed within the nuclear reactor core having a variable cross-section hollow channel and containing balls whose vertical location is determined by the flow of the reactor coolant through the column. The control column is divided into three basic sections wherein each of the sections has a different cross-sectional area. The uppermost section of the control column has the greatest cross-sectional area, the intermediate section of the control column has the smallest cross-sectional area, and the lowermost section of the control column has the intermediate cross-sectional area. In this manner, the area of the uppermost section can be established such that when the reactor coolant is flowing under normal conditions therethrough, the absorber balls will be lifted and suspended in a fluidized bed manner in the upper section. However, when the reactor coolant flow falls below a predetermined value, the absorber balls will fall through the intermediate section and into the lowermost section, thereby reducing the reactivity of the reactor core and shutting down the reactor.

  7. Column continuous transition functions

    NASA Astrophysics Data System (ADS)

    Li, Yangrong

    2007-04-01

    A column continuous transition function is by definition a standard transition function P(t) whose every column is continuous for t[greater-or-equal, slanted]0 in the norm topology of bounded sequence space l[infinity]. We will prove that it has a stable q-matrix and that there exists a one-to-one relationship between column continuous transition functions and increasing integrated semigroups on l[infinity]. Using the theory of integrated semigroups, we give some necessary and sufficient conditions under which the minimal q-function is column continuous, in terms of its generator (of the Markov semigroup) as well as its q-matrix. Furthermore, we will construct all column continuous Q-functions for a conservative, single-exit and column bounded q-matrix Q. As applications, we find that many interesting continuous-time Markov chains (CTMCs), say Feller-Reuter-Riley processes, monotone processes, birth-death processes and branching processes, etc., have column continuity.

  8. Optimized soluble expression and purification of an aggregation-prone protein by fusion tag systems and on-column cleavage in Escherichia coli.

    PubMed

    Li, Wen; Gao, Mingming; Liu, Wenchao; Kong, Yuelin; Tian, Hong; Yao, Wenbing; Gao, Xiangdong

    2012-12-01

    Previously we constructed a fusion protein based on GLP-1 and globular adiponectin but unfortunately its yield was low because it was mainly expressed as inclusion bodies. Herein to optimize the soluble expression of this fusion protein we tried several fusion tag systems. Fusion tags, including GST-, Trx- and MBP-tag, greatly improved the soluble expression of the fusion protein. However, these tag-fusion proteins were aggregation-prone as judged by Native PAGE and gel filtration chromatography, and this aggregation reduced the specificity of enterokinase-mediated enzyme cleavage which was essential to remove the fusion tags. To improve the specificity of protein cleavage, we employed on-column cleavage for downstream purification. Finally using optimized expression followed by on-column cleavage, we obtained the product fusion protein with a yield of 1.2 mg per g wet bacterial cells which was 8-fold higher than before. This method improved the yield and simplified the process, and as a convenient method it can also be used for the preparation of other aggregation-prone proteins.

  9. Mush Column Magma Chambers

    NASA Astrophysics Data System (ADS)

    Marsh, B. D.

    2002-12-01

    Magma chambers are a necessary concept in understanding the chemical and physical evolution of magma. The concept may well be similar to a transfer function in circuit or time series analysis. It does what needs to be done to transform source magma into eruptible magma. In gravity and geodetic interpretations the causative body is (usually of necessity) geometrically simple and of limited vertical extent; it is clearly difficult to `see' through the uppermost manifestation of the concentrated magma. The presence of plutons in the upper crust has reinforced the view that magma chambers are large pots of magma, but as in the physical representation of a transfer function, actual magma chambers are clearly distinct from virtual magma chambers. Two key features to understanding magmatic systems are that they are vertically integrated over large distances (e.g., 30-100 km), and that all local magmatic processes are controlled by solidification fronts. Heat transfer considerations show that any viable volcanic system must be supported by a vertically extensive plumbing system. Field and geophysical studies point to a common theme of an interconnected stack of sill-like structures extending to great depth. This is a magmatic Mush Column. The large-scale (10s of km) structure resembles the vertical structure inferred at large volcanic centers like Hawaii (e.g., Ryan et al.), and the fine scale (10s to 100s of m) structure is exemplified by ophiolites and deeply eroded sill complexes like the Ferrar dolerites of the McMurdo Dry Valleys, Antarctica. The local length scales of the sill reservoirs and interconnecting conduits produce a rich spectrum of crystallization environments with distinct solidification time scales. Extensive horizontal and vertical mushy walls provide conditions conducive to specific processes of differentiation from solidification front instability to sidewall porous flow and wall rock slumping. The size, strength, and time series of eruptive behavior

  10. Sensitivity of Tropospheric Chemical Composition to Halogen-Radical Chemistry Using a Fully Coupled Size-Resolved Multiphase Chemistry-Global Climate System: Halogen Distributions, Aerosol Composition, and Sensitivity of Climate-Relevant Gases

    SciTech Connect

    Long, M.; Keene, W. C.; Easter, Richard C.; Sander, Rolf; Liu, Xiaohong; Kerkweg, A.; Erickson, D.

    2014-04-07

    Observations and model studies suggest a significant but highly non-linear role for halogens, primarily Cl and Br, in multiphase atmospheric processes relevant to tropospheric chemistry and composition, aerosol evolution, radiative transfer, weather, and climate. The sensitivity of global atmospheric chemistry to the production of marine aerosol and the associated activation and cycling of inorganic Cl and Br was tested using a size-resolved multiphase coupled chemistry/global climate model (National Center for Atmospheric Research’s Community Atmosphere Model (CAM); v3.6.33). Simulation results showed strong meridional and vertical gradients in Cl and Br species. The simulation reproduced most available observations with reasonable confidence permitting the formulation of potential mechanisms for several previously unexplained halogen phenomena including the enrichment of Br- in submicron aerosol, and the presence of a BrO maximum in the polar free troposphere. However, simulated total volatile Br mixing ratios were generally high in the troposphere. Br in the stratosphere was lower than observed due to the lack of long-lived organobromine species in the simulation. Comparing simulations using chemical mechanisms with and without reactive Cl and Br species demonstrated a significant temporal and spatial sensitivity of primary atmospheric oxidants (O3, HOx, NOx), CH4, and non-methane hydrocarbons (NMHC’s) to halogen cycling. Simulated O3 and NOx were globally lower (65% and 35%, respectively, less in the planetary boundary layer based on median values) in simulations that included halogens. Globally, little impact was seen in SO2 and non-sea-salt SO42- processing due to halogens. Significant regional differences were evident: The lifetime of nss-SO42- was extended downwind of large sources of SO2. The burden and lifetime of DMS (and its oxidation products) were lower by a factor of 5 in simulations that included halogens, versus those without, leading to a 20

  11. Expanded Large-Scale Forcing Properties Derived from the Multiscale Data Assimilation System and Its Application to Single-Column Models

    NASA Astrophysics Data System (ADS)

    Feng, S.; Li, Z.; Liu, Y.; Lin, W.; Toto, T.; Vogelmann, A. M.; Fridlind, A. M.

    2013-12-01

    We present an approach to derive large-scale forcing that is used to drive single-column models (SCMs) and cloud resolving models (CRMs)/large eddy simulation (LES) for evaluating fast physics parameterizations in climate models. The forcing fields are derived by use of a newly developed multi-scale data assimilation (MS-DA) system. This DA system is developed on top of the NCEP Gridpoint Statistical Interpolation (GSI) System and is implemented in the Weather Research and Forecasting (WRF) model at a cloud resolving resolution of 2 km. This approach has been applied to the generation of large scale forcing for a set of Intensive Operation Periods (IOPs) over the Atmospheric Radiation Measurement (ARM) Climate Research Facility's Southern Great Plains (SGP) site. The dense ARM in-situ observations and high-resolution satellite data effectively constrain the WRF model. The evaluation shows that the derived forcing displays accuracies comparable to the existing continuous forcing product and, overall, a better dynamic consistency with observed cloud and precipitation. One important application of this approach is to derive large-scale hydrometeor forcing and multiscale forcing, which is not provided in the existing continuous forcing product. It is shown that the hydrometeor forcing poses an appreciable impact on cloud and precipitation fields in the single-column model simulations. The large-scale forcing exhibits a significant dependency on domain-size that represents SCM grid-sizes. Subgrid processes often contribute a significant component to the large-scale forcing, and this contribution is sensitive to the grid-size and cloud-regime.

  12. Mass transfer model liquid phase catalytic exchange column simulation applicable to any column composition profile

    SciTech Connect

    Busigin, A.

    2015-03-15

    Liquid Phase Catalytic Exchange (LPCE) is a key technology used in water detritiation systems. Rigorous simulation of LPCE is complicated when a column may have both hydrogen and deuterium present in significant concentrations in different sections of the column. This paper presents a general mass transfer model for a homogenous packed bed LPCE column as a set of differential equations describing composition change, and equilibrium equations to define the mass transfer driving force within the column. The model is used to show the effect of deuterium buildup in the bottom of an LPCE column from non-negligible D atom fraction in the bottom feed gas to the column. These types of calculations are important in the design of CECE (Combined Electrolysis and Catalytic Exchange) water detritiation systems.

  13. Global impacts of multiphase oxalate production

    NASA Astrophysics Data System (ADS)

    Tost, Holger; Taraborrelli, Domenico

    2013-04-01

    Fine mode atmospheric aerosols are dominated by the organic fraction. A large fraction of these organic compounds consists of oxalates and carboxylic acids. Some of these compounds are produced in the gas phase and then subsequently partition into aerosol particles whereas others are produced directly in the aqueous phase in either cloud droplets or deliquesced aerosol particles. In this study we investigate the contribution of oxalates to the global organic aerosol burden using a comprehensive atmospheric chemistry general circulation model including explicit multiphase chemistry schemes for clouds and aerosols. For that purpose the aqueous phase chemistry has been augmented by a mechanism for oxalates, combined with a consistent gas phase chemistry of corresponding oxidation products from isoprene degradation. Using these tools we will present an analysis of both budget and transport estimates which provide indications for the climate impact of these compounds.

  14. Large Interface Simulation in Multiphase Flow Phenomena

    SciTech Connect

    Henriques, Aparicio; Coste, Pierre; Pigny, Sylvain; Magnaudet, Jacques

    2006-07-01

    An attempt to represent multiphase multi-scale flow, filling the gap between Direct Numerical Simulation (DNS) and averaged approaches, is the purpose of this paper. We present a kind of Large Interface (LI) simulation formalism obtained after a filtering process on local instantaneous conservation equations of the two-fluid model which distinguishes between small scales and large scales contributions. LI surface tension force is also taken into account. Small scale dynamics call for modelization and large scale for simulation. Joined to this formalism, a criterion to recognize LI's is developed. It is used in an interface recognition algorithm which is qualified on a sloshing case and a bubble oscillation under zero-gravity. This method is applied to a rising bubble in a pool that collapses at a free surface and to a square-base basin experiment where splashing and sloshing at the free surface are the main break-up phenomena. (authors)

  15. Gas Kinematics in the Multiphase Circumgalactic Medium

    NASA Astrophysics Data System (ADS)

    Nielsen, Nikole M.; Kacprzak, Glenn G.; Churchill, Christopher W.; Murphy, Michael T.; Muzahid, Sowgat; Charlton, Jane C.; Evans, Jessica L.

    2017-03-01

    We use high-resolution Keck, VLT, or Hubble Space Telescope spectra of background quasars to examine the kinematic properties of the multiphase, metal-enriched circumgalactic medium in the outskirts of galaxies at 0.08 < z gal < 1.0, focusing on the low-ionization Mgii and high-ionization Ovi doublets. The absorption kinematics of low-ionization gas in the circumgalactic medium depend strongly on the star formation activity and the location about the host galaxy, where the largest velocity dispersions are associated with blue, face-on galaxies probed along the minor axis. Conversely, high-ionization gas kinematics are independent of galaxy star formation activity and orientation.

  16. Gasificaton Transport: A Multiphase CFD Approach & Measurements

    SciTech Connect

    Dimitri Gidaspow; Veeraya Jiradilok; Mayank Kashyap; Benjapon Chalermsinsuwan

    2009-02-14

    The objective of this project was to develop predictive theories for the dispersion and mass transfer coefficients and to measure them in the turbulent fluidization regime, using existing facilities. A second objective was to use our multiphase CFD tools to suggest optimized gasifier designs consistent with aims of Future Gen. We have shown that the kinetic theory based CFD codes correctly compute: (1) Dispersion coefficients; and (2) Mass transfer coefficients. Hence, the kinetic theory based CFD codes can be used for fluidized bed reactor design without any such inputs. We have also suggested a new energy efficient method of gasifying coal and producing electricity using a molten carbonate fuel cell. The principal product of this new scheme is carbon dioxide which can be converted into useful products such as marble, as is done very slowly in nature. We believe this scheme is a lot better than the canceled FutureGen, since the carbon dioxide is safely sequestered.

  17. Process tomography applied to multi-phase flow measurement

    NASA Astrophysics Data System (ADS)

    Dyakowski, T.

    1996-03-01

    This paper presents the state of the art in measuring multi-phase flows by using tomographic techniques. The results presented show a wide range of industrial applications of process tomography from the nuclear and chemical to the food industry. This is illustrated by examples of the application of various tomographic sensors to the measurement of geometric or kinematic parameters of multi-phase flows. An application of process tomography for the validation of computational fluid dynamic models and the possibility of constructing a flowmeter for multi-phase flow are addressed.

  18. Enantiomeric separation of mineralocorticoid receptor (hMR) antagonists using the Chiralcel OJ-H HPLC column with novel polar cosolvent eluent systems.

    PubMed

    Sharp, V Scott; Kennedy, Joseph H; Belvo, Matthew D; Williams, Jeffrey D; Risley, Donald S; Seest, Eric P

    2006-06-01

    This study demonstrates the increased versatility of the Chiralcel OJ-H stationary phase when using various alcohol/acetonitrile mobile phases. This chiral stationary phase has traditionally been employed in the normal phase mode and more recently with neat alcohols as eluents. Selected isomeric human mineralocorticoid receptor (hMR) antagonist pharmaceutical candidates and synthetic intermediates were separated using the Chiralcel OJ-H HPLC column with novel polar cosolvent eluent systems. The capacity factors, resolution, and selectivity of the chiral separations were assessed while varying the alcohol/acetonitrile composition and alcohol identity. The mixed polar eluents provide separations that are nearly always superior to both the traditional hexane-rich and single-alcohol "polar organic" eluents for the compounds tested in this article.

  19. Fabrication and characterization of microelectromechanical systems-based gas chromatography column with embedded micro-posts for separation of environmental carcinogens.

    PubMed

    Sun, Jianhai; Cui, Dafu; Chen, Xing; Zhang, Lulu; Cai, Haoyuan; Li, Hui

    2013-05-24

    In this paper, a micro gas chromatography (μGC) column with embedded micro-posts was developed for increasing overall surface area of the columns which is able to support more of the stationary phase and reducing the effective width of the column, leading to higher separation efficiency. The proposed columns have a higher sample capacity as the overall surface area is about 3 times larger than that of open columns with the same dimensions. In order to achieve an even flow velocity in the channels, the location of the micro-posts in the linear channels and the configuration of curved channels were optimized by numerical simulation. The results have indicated that the proposed column separated 5 environmental carcinogens in less than 50s, achieved a separation efficiency of about 9500plates/m and eluted highly symmetrical Gaussian peaks.

  20. Maintenance of column performance at scale.

    PubMed

    William, Alan; Taylor, Kathy; Dambuleff, Kyril; Persson, Owe; Kennedy, Robert M

    2002-01-25

    Pack-in-place column packing methods were developed for Q Sepharose Big Beads at 40 cm I.D. and scaled up to 200 cm I.D. in Chromaflow columns. The efficiency and asymmetry of the packed bed were evaluated as a function of test velocity and sample volume. The performance of the packed beds at both scales approached the theoretical limits of column performance (Hred =2 and Af=1) expected in small analytical columns. The packing strategy was effective for scale up and the stability of the packed beds, the effectiveness of the column design with respect to the mobile phase distribution system and the stability of the media to the pack-in-place technology, are presented.

  1. A Versatile, Automatic Chromatographic Column Packing Device

    ERIC Educational Resources Information Center

    Barry, Eugene F.; And Others

    1977-01-01

    Describes an inexpensive apparatus for packing liquid and gas chromatographic columns of high efficiency. Consists of stainless steel support struts, an Automat Getriebmotor, and an associated three-pulley system capable of 10, 30, and 300 rpm. (MLH)

  2. Numerical Simulation of Compressible Multi-phase flows using HLLC extension of AUSM +-up Scheme

    NASA Astrophysics Data System (ADS)

    Dhir, Gaurav; Bodi, Kowsik

    2016-11-01

    Solving Multi-fluid equations has always required an onerous effort from researchers with regards to implementing an appropriate numerical scheme which could capture the various facets of such type of flows along with the interaction between the various phases present. Additionally, multi-phase flows bring with them peculiar mathematical properties such as non-hyperbolicity and non-conservativeness which further increases the complexity involved. Our presentation shall present an insight into the advantages and limitations of several numerical schemes proposed in the past and propose to use the HLLC extension of AUSM +-up approach to model such type of flows. We use the single pressure based stratified flow concept and by presenting several test cases, we prove that our method robustly computes multi-phase flow involving discontinuities, such as shock waves and fluid interfaces. Additionally, we present a formulation to incorporate phase transition within multi-fluid equations and establish the validity of this method by presenting several two dimensional test cases such as the Shock-Water Column Interaction problem, the Water-Shock/Air Bubble Interaction problem and the 2D Underwater Explosion problem. Industrial Research and Consultancy Centre, IIT Bombay.

  3. Enhanced removal of organic matter and ammoniacal-nitrogen in a column experiment of tidal flow constructed wetland system.

    PubMed

    Sun, Guangzhi; Zhao, Yaqian; Allen, Stephen

    2005-01-26

    A tidal flow constructed wetland system was investigated for the removal of organic matter and ammoniacal-nitrogen from diluted piggery wastewater. The results demonstrated that the operation of tidal flow enhanced the transfer of oxygen into wetland matrices. The supply of oxygen by the operation (473 gO2/m2d) matched the demand for wastewater treatment. The overall oxygen consumption rate in the system was considerably higher than the typical rate obtainable in conventional wetlands; most oxygen being used for the decomposition of organic matter. Compared with conventional systems, the tidal flow system demonstrated greater efficiency in the removal of organic matter. Significant nitrification did not take place, although 27-48% ammonia was removed from the wastewater. Immobilization by microbial cells and adsorption were the likely routes to remove ammonia under the specific experiment conditions. Percentage removals of BOD5, NH4-N and SS increased after effluent recirculation at a ratio of 1:1 was employed.

  4. Signal generator converts direct current to multiphase supplies

    NASA Technical Reports Server (NTRS)

    Baude, J.

    1967-01-01

    Multiphase wave generator uses multivibrators in a feedback control mode that produces output signal pairs that are impressed on the primary windings of inverter transformers sequentially with a 120 degree phase shift from each other.

  5. Multi-Phase Extraction: State-of-the-Practice

    EPA Pesticide Factsheets

    This report describes the state-of-the-practice for multi-phase extraction (MPE) of contaminated soil and groundwater, focusing primarily on the application and use of MPE at sites with halogenated volatile organic compounds (VOCs).

  6. A model for multiphase flows through poroelastic media

    SciTech Connect

    Ahmadi, Goodarz; Mazaheri, Ali Reza; Smith, D.H

    2003-01-01

    A continuum model for multiphase fluid mixture flows through poroelastic media is presented. The basic conservation laws developed via a volume averaging technique are considered. Effects of phasic equilibrated forces are included in the model. Based on the thermodynamics of the multiphase mixture flows, appropriate constitutive equations are formulated. The entropy inequality is exploited, and the method of Lagrangian multiplier is used along with the phasic conservation laws to derive the constitutive equations for the phasic stress tensors, equilibrated stress vectors, and the interactions terms. The special cases of wave propagation in poroelastic media saturated with multiphase fluids, and multiphase flows through porous media, are studied. It is shown that the present theory leads to the extended Darcy’s law and contains, as a special case, Biot’s theory of saturated poroelastic media.

  7. Multiphase pumping: The lessons of long-term field testing

    SciTech Connect

    Elf-Aquitaine, E.L.; Taiani, S.

    1995-12-31

    The field testing of a POSEIDON rotodynamic helicoaxial pump (P302) manufactured by SULZER is being conducted since June 1994 on the Elf Aquitaine`s onshore site of the PECORADE oil field located in the south-west of France. This one-year testing program is aimed at qualifying this design of multiphase pump for future field applications. The multiphase pump has been previously tested at the IFP`s test loop of SOLAIZE for factory acceptance and performance test. This paper describes the PECORADE multiphase loop, the multiphase pump testing procedures and the results obtained in the field of performance, sensitivity, and endurance. The operational and maintenance lessons to be learned from this long-term field testing are presented from the point of view of the operator.

  8. Benchmark initiative on coupled multiphase flow and geomechanical processes during CO2 injection

    NASA Astrophysics Data System (ADS)

    Benisch, K.; Annewandter, R.; Olden, P.; Mackay, E.; Bauer, S.; Geiger, S.

    2012-12-01

    cap rock. For the second case, a fault is introduced to investigate the risk of fault reactivation and fracturing due to CO2 injection for a single and a multiple cap rock system, respectively. A multiple injector setting exposed to different tectonic stress regimes is proposed for the third case. Hereby, a 3D model is used compartmentalized by low permeability faults, which become permeable due to injection. Injection scenarios will be evaluated for extensional and compressive stress regimes. All model set-ups are based on already published simulation results of coupled multiphase flow and geomechanical processes during CO2 injection. To end with, a real site geometry including parameterization and realistic reservoir conditions is provided. The benchmark design and cases will be presented as well as some preliminary simulation results for the first cases. Interested institutions and researchers are invited to discuss and to participate in the study.

  9. Effect of biological and adsorption interactions on removal of organic material from synthetic-fuel waste water in batch and column systems

    SciTech Connect

    Elgezawi, S.M.

    1986-01-01

    The effect of temperature on total organic carbon removal from synthetic fuel waste water by activated carbon was evaluated, at temperatures of 5, 15, 25, and 40/sup 0/C. Both batch and continuous studies were performed using granular Darco H90 activated carbon, Calgon Filtrasorb 400, carbon black 2000, and glass beads as adsorbents for organics in Run-19, Run-20, Omega-9, oil shale retort water and Hanna 1VB-02W-02U coal gasification condensate. Experimental adsorption isotherms were compared with results predicted by the Langmuir and Freundlich models. Breakthrough curves were compared with curves predicted by the Thomas model. The rate controlling mechanisms in continuous flow adsorption system including second order reversible surface kinetics, external film resistance and internal particle resistance were also evaluated. Granular activated carbons coated with a bacterial film combining physical adsorption and biological removal of organics into one unit called adsorption/biodegradation unit were also investigated. This study included determination of bacterial numbers in batch and continuous flow systems at different heights in the column ad at different temperatures. In developing a modified Thomas model, which included the bacterial activity occurring inside the fixed-packed bed system, mass transfer coefficients were evaluated to establish the relative importance of various individual mechanisms that contributed to the overall adsorption process. Biological film thickness was found to be a significant parameter in modeling the adsorption systems studied.

  10. Uncertainty quantification and sensitivity analysis of volcanic columns models: Results from the integral model PLUME-MoM

    NASA Astrophysics Data System (ADS)

    de'Michieli Vitturi, M.; Engwell, S. L.; Neri, A.; Barsotti, S.

    2016-10-01

    The behavior of plumes associated with explosive volcanic eruptions is complex and dependent on eruptive source parameters (e.g. exit velocity, gas fraction, temperature and grain-size distribution). It is also well known that the atmospheric environment interacts with volcanic plumes produced by explosive eruptions in a number of ways. The wind field can bend the plume but also affect atmospheric air entrainment into the column, enhancing its buoyancy and in some cases, preventing column collapse. In recent years, several numerical simulation tools and observational systems have investigated the action of eruption parameters and wind field on volcanic column height and column trajectory, revealing an important influence of these variables on plume behavior. In this study, we assess these dependencies using the integral model PLUME-MoM, whereby the continuous polydispersity of pyroclastic particles is described using a quadrature-based moment method, an innovative approach in volcanology well-suited for the description of the multiphase nature of magmatic mixtures. Application of formalized uncertainty quantification and sensitivity analysis techniques enables statistical exploration of the model, providing information on the extent to which uncertainty in the input or model parameters propagates to model output uncertainty. In particular, in the framework of the IAVCEI Commission on tephra hazard modeling inter-comparison study, PLUME-MoM is used to investigate the parameters exerting a major control on plume height, applying it to a weak plume scenario based on 26 January 2011 Shinmoe-dake eruptive conditions and a strong plume scenario based on the climatic phase of the 15 June 1991 Pinatubo eruption.

  11. Mixing of cryogenic fluids and predicted detonation properties for multiphase liquid oxygen and liquid hydrogen

    NASA Technical Reports Server (NTRS)

    Bishop, C. V.; Benz, F. J.; Ullian, L. J.

    1986-01-01

    The mixing and explosion of LOX and LH sub 2 is a concern for Space Transportation System operations. To understand this problem, cryogenic mixing is experimentally studied by pouring 1,2,2 trichloro 2,1,1 trifluoroethane (Freon 113) into LN sub 2, LN sub 2 into LH sub 2, and LH sub 2 into into LN sub 2 in a 1 m by 15 cm cylindrical glass vessel. Data from these experiments is compared with previous studies and a hypothesis is advanced that LOX/LH sub 2 mixing will result in a complex, heterogenous, multiphase aggregation including LOX, SOX, LH sub 2, and VH sub 2 using the multiphase hypothesis. Visual and x ray observations of the process and mass measurements are reported.

  12. Smoothed dissipative particle dynamics model for mesoscopic multiphase flows in the presence of thermal fluctuations

    SciTech Connect

    Lei, Huan; Baker, Nathan A.; Wu, Lei; Schenter, Gregory K.; Mundy, Christopher J.; Tartakovsky, Alexandre M.

    2016-08-05

    Thermal fluctuations cause perturbations of fluid-fluid interfaces and highly nonlinear hydrodynamics in multiphase flows. In this work, we develop a novel multiphase smoothed dissipative particle dynamics model. This model accounts for both bulk hydrodynamics and interfacial fluctuations. Interfacial surface tension is modeled by imposing a pairwise force between SDPD particles. We show that the relationship between the model parameters and surface tension, previously derived under the assumption of zero thermal fluctuation, is accurate for fluid systems at low temperature but overestimates the surface tension for intermediate and large thermal fluctuations. To analyze the effect of thermal fluctuations on surface tension, we construct a coarse-grained Euler lattice model based on the mean field theory and derive a semi-analytical formula to directly relate the surface tension to model parameters for a wide range of temperatures and model resolutions. We demonstrate that the present method correctly models the dynamic processes, such as bubble coalescence and capillary spectra across the interface.

  13. Proper Orthogonal Decomposition on Experimental Multi-phase Flow in a Pipe

    NASA Astrophysics Data System (ADS)

    Viggiano, Bianca; Tutkun, Murat; Cal, Raúl Bayoán

    2016-11-01

    Multi-phase flow in a 10 cm diameter pipe is analyzed using proper orthogonal decomposition. The data were obtained using X-ray computed tomography in the Well Flow Loop at the Institute for Energy Technology in Kjeller, Norway. The system consists of two sources and two detectors; one camera records the vertical beams and one camera records the horizontal beams. The X-ray system allows measurement of phase holdup, cross-sectional phase distributions and gas-liquid interface characteristics within the pipe. The mathematical framework in the context of multi-phase flows is developed. Phase fractions of a two-phase (gas-liquid) flow are analyzed and a reduced order description of the flow is generated. Experimental data deepens the complexity of the analysis with limited known quantities for reconstruction. Comparison between the reconstructed fields and the full data set allows observation of the important features. The mathematical description obtained from the decomposition will deepen the understanding of multi-phase flow characteristics and is applicable to fluidized beds, hydroelectric power and nuclear processes to name a few.

  14. Multiphase-pump field trials demonstrate practical applications for the technology

    SciTech Connect

    Dal Porto, D.F.; Larson, L.A.

    1997-08-01

    This paper presents the results of two multiphase-pump field trials. One field trial was conducted offshore on a platform in the Gulf of Mexico (GOM). It is a low-pressure boost (100 psi) application involving gas-lifted wells. The other field trial was conducted onshore in an oil field in Alberta, Canada. This multiphase pump was designed for a high-pressure boost (850 psi) capability with primarily rod-pumped wells feeding the suction of the pump. The offshore pump was sized to handle the flow from one well. By lowering the back pressure on the well, increased production was realized. The increased flow from one of the wells far surpassed the predicted quantity. Early problems with the double mechanical seal system were overcome and a new, simplified single mechanical seal system has been designed and installed. The onshore multiple pump clearly demonstrated that a twin-screw pump can operate reliably in a field environment, even under severe slug flow conditions. The trial indicated that a considerable portion of the liquid in the recycle stream (required because of the high gas fraction of the multiphase fluid from the field) flashes into gas, which occupies more volume in the pump than if it remained liquid. This decreased the capability of the pump to handle net flow from the field. These conditions motivated a re-evaluation of the pump-sizing techniques. Performance data and lessons learned information are presented for both field trials.

  15. Identifying Methane Sources in Groundwater; Quantifying Changes in Compositional and Stable Isotope Values during Multiphase Transport

    NASA Astrophysics Data System (ADS)

    Larson, T.; Sathaye, K.

    2014-12-01

    A dramatic expansion of hydraulic fracturing and horizontal drilling for natural gas in unconventional reserves is underway. This expansion is fueling considerable public concern, however, that extracted natural gas, reservoir brines and associated fracking fluids may infiltrate to and contaminate shallower (< 500m depth) groundwater reservoirs, thereby posing a health threat. Attributing methane found in shallow groundwater to either deep thermogenic 'fracking' operations or locally-derived shallow microbial sources utilizes geochemical methods including alkane wetness and stable carbon and hydrogen isotope ratios of short chain (C1-C5) hydrocarbons. Compared to shallow microbial gas, thermogenic gas is wetter and falls within a different range of δ13C and δD values. What is not clear, however, is how the transport of natural gas through water saturated geological media may affect its compositional and stable isotope values. What is needed is a means to differentiate potential flow paths of natural gas including 'fast paths' along preexisting fractures and drill casings vs. 'slow paths' through low permeability rocks. In this study we attempt quantify transport-related effects using experimental 1-dimensional two-phase column experiments and analytical solutions to multi-phase gas injection equations. Two-phase experimental results for an injection of natural gas into a water saturated column packed with crushed illite show that the natural gas becomes enriched in methane compared to ethane and propane during transport. Carbon isotope measurements are ongoing. Results from the multi-phase gas injection equations that include methane isotopologue solubility and diffusion effects predict the development of a 'bank' of methane depleted in 13C relative to 12C at the front of a plume of fugitive natural gas. These results, therefore, suggest that transport of natural gas through water saturated geological media may complicate attribution methods needed to distinguish

  16. The Impact of a Multi-Phased Assessment on the Planning, Implementation and Management of Federal Education Programs.

    ERIC Educational Resources Information Center

    Scott, Aurelia C.

    The effects of a multi-phased assessment on the management and modification of Federal special education programs and policy is discussed. The purposes and methodology of the three-part assessment procedures (evaluability assessment, rapid feedback assessment, and the performance monitoring system) are presented. This is followed by a description…

  17. Fate and transport of carbamazepine in a soil aquifer treatment (SAT) system: evaluation of a monitoring study and soil column experiments

    NASA Astrophysics Data System (ADS)

    Arye, G.; Dror, I.; Berkowitz, B.

    2009-12-01

    Carbamazepine (CBZ), an anticonvulsant and mood stabilizing drug, is found to be highly persistent in wastewater treatment plants and when subsequently released to the environment. Because of its physicochemical properties, CBZ is only weakly sorbed to mineral soils and is resistant to biodegradation. As a consequence, CBZ has been suggested as an appropriate anthropogenic marker to track the fate of wastewater in aquatic systems. We study the fate and transport of CBZ in the Dan Region Reclamation Project (Shafdan) in Israel, where about one quarter of the country’s wastewater undergoes purification. The secondary treatment of raw wastewater consists of mechanical and biological treatment by activated sludge, with an additional step of nitrification-denitrification, and subsequent recharge of treated effluent to groundwater via infiltration basins, as a complementary tertiary treatment known as soil aquifer treatment (SAT). Water produced from the SAT system is pumped from a depth of 100-200 m by means of approximately 100 recovery wells, located 300-1,500 m from the recharge basins. This water is then delivered through a single 87 km long pipeline to the southern part of the country, where it is used for irrigation. We examine the fate of CBZ before and after treatment with the SAT system. To date, our monitoring has detected up to 1300 ng/L of CBZ in the recharged effluent before SAT, and up to 700 ng/L after treatment, prior to use for irrigation. The latter may considered as an aggregate value from all recovery wells. Additional information on CBZ transport characteristics has been gained from a series of soil column experiments using soil samples taken from the SAT infiltration basin to a depth of 170 cm. For each soil layer examined, the soil column was first leached of CBZ and subsequently loaded with secondary treated wastewater containing CBZ. The CBZ breakthrough curves resemble transport of a conservative tracer in most of the soil samples. We

  18. Computational modeling of multiphase flow and transport with Python

    NASA Astrophysics Data System (ADS)

    Kees, C. E.; Farthing, M. W.; Hines, A. M.; Howington, S. E.

    2008-12-01

    Computational flow and transport models play an important role in many hydrological investigations. Unfortunately, developing simulators that are efficient, widely applicable, and robust is a challenge. This is particularly true if the target applications include complications like multiple fluid phases with multiple components and material heterogeneity. To be specific, these problems often involve physical phenomena at multiple spatial and temporal scales. The appropriate formulation may evolve, and the systems of partial differential equations (PDEs) that arise from traditional formulations can be hard to solve efficiently at the desired resolution. Here, we discuss the development of a Python-based modeling framework for finite element approximation of systems of nonlinear PDEs with an emphasis on multiphase, multicomponent systems relevant for surface and subsurface hydrology. In addition to the overall approach and application, we consider the role of Python in managing code complexity, providing user interfaces, developing solution algorithms, and implementing numerical methods for execution on serial and parallel platforms. We evaluate trade-offs and design choices that follow from our use of Python versus other languages like C++ or Fortran and consider the impact on performance measured in terms of metrics like memory usage, execution time, and developer time.

  19. Cross flow cyclonic flotation column for coal and minerals beneficiation

    SciTech Connect

    Lai, R.W.; Patton, R.A.

    2000-05-02

    An apparatus and process are disclosed for the separation of coal from pyritic impurities using a modified froth flotation system. The froth flotation column incorporates a helical track about the inner wall of the column in a region intermediate between the top and base of the column. A standard impeller located about the central axis of the column is used to generate a centrifugal force thereby increasing the separation efficiency of coal from the pyritic particles and hydrophilic tailings.

  20. Cross flow flotation column for coal and minerals beneficiation

    SciTech Connect

    Lai, Ralph W.; Patton, Robert A.

    1997-12-01

    An apparatus and process are disclosed for the separation of coal from pyritic impurities using a modified froth flotation system. The froth flotation column incorporates a helical track about the inner wall of the column in a region intermediate between the top and base of the column. A standard impeller located about the central axis of the column is used to generate a centrifugal force thereby increasing the separation efficiency of coal from the pyritic particles and hydrophilic tailings.

  1. Cross flow cyclonic flotation column for coal and minerals beneficiation

    DOEpatents

    Lai, Ralph W.; Patton, Robert A.

    2000-01-01

    An apparatus and process for the separation of coal from pyritic impurities using a modified froth flotation system. The froth flotation column incorporates a helical track about the inner wall of the column in a region intermediate between the top and base of the column. A standard impeller located about the central axis of the column is used to generate a centrifugal force thereby increasing the separation efficiency of coal from the pyritic particles and hydrophillic tailings.

  2. Technical Report on NETL's Non Newtonian Multiphase Slurry Workshop: A path forward to understanding non-Newtonian multiphase slurry flows

    SciTech Connect

    Edited by Guenther, Chris; Garg, Rahul

    2013-08-19

    The Department of Energy’s (DOE) National Energy Technology Laboratory (NETL) sponsored a workshop on non-Newtonian multiphase slurry at NETL’s Morgantown campus August 19 and 20, 2013. The objective of this special two-day meeting of 20-30 invited experts from industry, National Labs and academia was to identify and address technical issues associated with handling non-Newtonian multiphase slurries across various facilities managed by DOE. Particular emphasis during this workshop was placed on applications managed by the Office of Environmental Management (EM). The workshop was preceded by two webinars wherein personnel from ORP and NETL provided background information on the Hanford WTP project and discussed the critical design challenges facing this project. In non-Newtonian fluids, viscosity is not constant and exhibits a complex dependence on applied shear stress or deformation. Many applications under EM’s tank farm mission involve non-Newtonian slurries that are multiphase in nature; tank farm storage and handling, slurry transport, and mixing all involve multiphase flow dynamics, which require an improved understanding of the mechanisms responsible for rheological changes in non-Newtonian multiphase slurries (NNMS). To discuss the issues in predicting the behavior of NNMS, the workshop focused on two topic areas: (1) State-of-the-art in non-Newtonian Multiphase Slurry Flow, and (2) Scaling up with Confidence and Ensuring Safe and Reliable Long-Term Operation.

  3. MULTI-PHASE FRACTURE-MATRIX INTERACTIONS UNDER STRESS CHANGES

    SciTech Connect

    A.S. Grader; D. Elsworth; P.M. Halleck; F. Alvarado; H. Yasuhara; A. Alajmi; Z. Karpyn

    2002-10-28

    The main objectives of this project are to quantify the changes in fracture porosity and multiphase transport properties as a function of confining stress. These changes will be integrated into conceptual and numerical models that will improve our ability to predict and optimize fluid transport in fractured system. This report details our progress on: (1) developing the direct experimental measurements of fracture aperture and topology using high-resolution x-ray microtomography, (2) modeling of fracture permeability in the presence of asperities and confining stress, and (3) simulation of two-phase fluid flow in a fracture and a layered matrix. The three-dimensional surface that describes the large-scale structure of the fracture in the porous medium can be determined using x-ray micro-tomography with significant accuracy. The distribution of fracture aperture is a difficult issue that we are studying and developing methods of quantification. The difficulties are both numerical and conceptual. Numerically, the three-dimensional data sets include millions, and sometimes, billions of points, and pose a computational challenge. The conceptual difficulties derive from the rough nature of the fracture surfaces, and the heterogeneous nature of the rock matrix. However, the high-resolution obtained by the imaging system provides us a much needed measuring environment on rock samples that are subjected to simultaneous fluid flow and confining stress. Pilot multi-phase experiments have been performed, proving the ability to detect two phases in certain large fractures. The absolute permeability of a fracture depends on the behavior of the asperities that keep it open. A model is being developed that predicts the permeability and average aperture of a fracture as a function of time under steady flow of water including the pressure solution at the asperity contact points. Several two-phase flow experiments in the presence of a fracture tip were performed in the past. At the

  4. SPACCIM simulations of chemical aerosol-cloud interactions with the multiphase chemical mechanism MCM-CAPRAM3.0i

    NASA Astrophysics Data System (ADS)

    Tilgner, A.; Schrödner, R.; Bräuer, P.; Wolke, R.; Herrmann, H.

    2010-07-01

    detailed description of tropospheric aqueous phase organic chemistry: CAPRAM 3.0, Atmos Environ, 39, 4351-4363, 2005. Saunders, S. M., Jenkin, M. E., Derwent, R. G., and Pilling, M. J.: Protocol for the development of the Master Chemical Mechanism, MCM v3 (Part A): tropospheric degradation of non-aromatic volatile organic compounds, Atmos Chem Phys, 3, 161-180, 2003. Tilgner, A., and Herrmann, H.: Radical-driven carbonyl-to-acid conversion and acid degradation in tropospheric aqueous systems studied by CAPRAM, submitted to Atmospheric Environment, 2010. Wolke, R., Sehili, A. M., Simmel, M., Knoth, O., Tilgner, A., and Herrmann, H.: SPACCIM: A parcel model with detailed microphysics and complex multiphase chemistry, Atmos Environ, 39, 4375-4388, 2005.

  5. Determination of histamine in wines with an on-line pre-column flow derivatization system coupled to high performance liquid chromatography.

    PubMed

    García-Villar, Natividad; Saurina, Javier; Hernández-Cassou, Santiago

    2005-09-01

    A new rapid and sensitive high performance liquid chromatography (HPLC) method for determining histamine in red wine samples, based on continuous flow derivatization with 1,2-naphthoquinone-4-sulfonate (NQS), is proposed. In this system, samples are derivatized on-line in a three-channel flow manifold for reagent, buffer and sample. The reaction takes place in a PTFE coil heated at 80 degrees C and with a residence time of 2.9 min. The reaction mixture is injected directly into the chromatographic system, where the histamine derivative is separated from other aminated compounds present in the wine matrix in less than ten minutes. The HPLC procedure involves a C18 column, a binary gradient of 2% acetic acid-methanol as a mobile phase, and UV detection at 305 nm. Analytical parameters of the method are evaluated using red wine samples. The linear range is up to 66.7 mg L(-1) (r = 0.9999), the precision (RSD) is 3%, the detection limit is 0.22 mg L(-1), and the average histamine recovery is 101.5% +/- 6.7%. Commercial red wines from different Spanish regions are analyzed with the proposed method.

  6. Characterization and in-vivo evaluation of potential probiotics of the bacterial flora within the water column of a healthy shrimp larviculture system

    NASA Astrophysics Data System (ADS)

    Xue, Ming; Liang, Huafang; He, Yaoyao; Wen, Chongqing

    2016-05-01

    A thorough understanding of the normal bacterial flora associated with shrimp larviculture systems contributes to probiotic screening and disease control. The bacterial community of the water column over a commercial Litopenaeus vannamei larval rearing run was characterized with both culture-dependent and culture-independent methods. A total of 27 phylotypes at the species level were isolated and identified based on 16S rDNA sequence analysis. Denaturing gradient gel electrophoresis (DGGE) analysis of the V3-V5 region of 16S rRNA genes showed a dynamic bacterial community with major changes occurred from stages zoea to mysis during the rearing run. The sequences retrieved were affiliated to four phyla, Proteobacteria, Actinobacteria, Bacteroidetes, and Firmicutes, with the family Rhodobacteraceae being the most frequently recovered one. Subsequently, 13 representative strains conferred higher larval survival than the control when evaluated in the in-vivo experiments; in particular, three candidates, assigned to Phaeobacter sp., Arthrobacter sp., and Microbacterium sp., significantly improved larval survival ( P < 0.05). Therefore, the healthy shrimp larviculture system harbored a diverse and favorable bacterial flora, which contribute to larval development and are of great importance in exploiting novel probiotics.

  7. Multicomponent, multiphase flow in porous media with temperature variation

    SciTech Connect

    Wingard, J.S.; Orr, F.M. Jr.

    1990-10-01

    Recovery of hydrocarbons from porous media is an ongoing concern. Advanced techniques augment conventional recovery methods by injecting fluids that favorably interact with the oil. These fluids interact with the oil by energy transfer, in the case of steam injection, or by mass transfer, as in a miscible gas flood. Often both thermal and compositional considerations are important. An understanding of these injection methods requires knowledge of how temperature variations, phase equilibrium and multiphase flow in porous media interact. The material balance for each component and energy balance are cast as a system of non-strictly hyperbolic partial differential equations. This system of equations is solved using the method of characteristics. The model takes into account the phase behavior by using the Peng-Robinson equation of state to partition the individual components into different phases. Temperature effects are accounted for by the energy balance. Flow effects are modelled by using fractional flow curves and a Stone's three phase relative permeability model. Three problems are discussed. The first problem eliminates the phase behavior aspect of the problem by studying the flow of a single component as it undergoes an isothermal phase change. The second couples the effects of temperature and flow behavior by including a second component that is immiscible with the original component. Phase behavior is added by using a set of three partially miscible components that partition into two or three separate phases. 66 refs., 54 figs., 14 tabs.

  8. Columns in Clay

    ERIC Educational Resources Information Center

    Leenhouts, Robin

    2010-01-01

    This article describes a clay project for students studying Greece and Rome. It provides a wonderful way to learn slab construction techniques by making small clay column capitols. With this lesson, students learn architectural vocabulary and history, understand the importance of classical architectural forms and their influence on today's…

  9. The impact of sedimentary alkalinity release on the water column CO2 system in the North Sea

    NASA Astrophysics Data System (ADS)

    Brenner, H.; Braeckman, U.; Le Guitton, M.; Meysman, F. J. R.

    2015-08-01

    Recently, it has been proposed that alkalinity release from sediments can play an important role in the carbonate dynamics on continental shelves, lowering the pCO2 of seawater and hence increasing the CO2 uptake from the atmosphere. To test this hypothesis, sedimentary alkalinity generation was quantified within permeable and muddy sediments across the North Sea during two cruises in September 2011 (basin-wide) and June 2012 (Dutch coastal zone). Benthic fluxes of alkalinity (AT) and dissolved inorganic carbon (DIC) were determined using shipboard closed sediment incubations. These results show that sediments can be an important source for alkalinity, particularly in the shallow southern North Sea, where high AT and DIC fluxes were recorded in near shore sediments of the Belgian, Dutch and German coastal zone. In contrast, fluxes of AT and DIC are substantially lower in the deeper, seasonally stratified, northern part of the North Sea. Overall, our results show that sedimentary alkalinity generation should be considered an important factor in the CO2 dynamics of shallow coastal systems.

  10. The impact of sedimentary alkalinity release on the water column CO2 system in the North Sea

    NASA Astrophysics Data System (ADS)

    Brenner, H.; Braeckman, U.; Le Guitton, M.; Meysman, F. J. R.

    2016-02-01

    It has been previously proposed that alkalinity release from sediments can play an important role in the carbonate dynamics on continental shelves, lowering the pCO2 of seawater and hence increasing the CO2 uptake from the atmosphere. To test this hypothesis, sedimentary alkalinity generation was quantified within cohesive and permeable sediments across the North Sea during two cruises in September 2011 (basin-wide) and June 2012 (Dutch coastal zone). Benthic fluxes of oxygen (O2), alkalinity (AT) and dissolved inorganic carbon (DIC) were determined using shipboard closed sediment incubations. Our results show that sediments can form an important source of alkalinity for the overlying water, particularly in the shallow southern North Sea, where high AT and DIC fluxes were recorded in near-shore sediments of the Belgian, Dutch and German coastal zone. In contrast, fluxes of AT and DIC are substantially lower in the deeper, seasonally stratified, northern part of the North Sea. Based on the data collected, we performed a model analysis to constrain the main pathways of alkalinity generation in the sediment, and to quantify how sedimentary alkalinity drives atmospheric CO2 uptake in the southern North Sea. Overall, our results show that sedimentary alkalinity generation should be regarded as a key component in the CO2 dynamics of shallow coastal systems.

  11. Multiphase wavetrains, singular wave interactions and the emergence of the Korteweg–de Vries equation

    PubMed Central

    Bridges, Thomas J.

    2016-01-01

    Multiphase wavetrains are multiperiodic travelling waves with a set of distinct wavenumbers and distinct frequencies. In conservative systems, such families are associated with the conservation of wave action or other conservation law. At generic points (where the Jacobian of the wave action flux is non-degenerate), modulation of the wavetrain leads to the dispersionless multiphase conservation of wave action. The main result of this paper is that modulation of the multiphase wavetrain, when the Jacobian of the wave action flux vector is singular, morphs the vector-valued conservation law into the scalar Korteweg–de Vries (KdV) equation. The coefficients in the emergent KdV equation have a geometrical interpretation in terms of projection of the vector components of the conservation law. The theory herein is restricted to two phases to simplify presentation, with extensions to any finite dimension discussed in the concluding remarks. Two applications of the theory are presented: a coupled nonlinear Schrödinger equation and two-layer shallow-water hydrodynamics with a free surface. Both have two-phase solutions where criticality and the properties of the emergent KdV equation can be determined analytically. PMID:28119546

  12. Application of multiphase modelling for vortex occurrence in vertical pump intake - a review

    NASA Astrophysics Data System (ADS)

    Samsudin, M. L.; Munisamy, K. M.; Thangaraju, S. K.

    2015-09-01

    Vortex formation within pump intake is one of common problems faced for power plant cooling water system. This phenomenon, categorised as surface and sub-surface vortices, can lead to several operational problems and increased maintenance costs. Physical model study was recommended from published guidelines but proved to be time and resource consuming. Hence, the use of Computational Fluid Dynamics (CFD) is an attractive alternative in managing the problem. At the early stage, flow analysis was conducted using single phase simulation and found to find good agreement with the observation from physical model study. With the development of computers, multiphase simulation found further enhancement in obtaining accurate results for representing air entrainment and sub-surface vortices which were earlier not well predicted from the single phase simulation. The purpose of this paper is to describe the application of multiphase modelling with CFD analysis for investigating vortex formation for a vertically inverted pump intake. In applying multiphase modelling, there ought to be a balance between the acceptable usage for computational time and resources and the degree of accuracy and realism in the results as expected from the analysis.

  13. A lattice Boltzmann model for multiphase flows interacting with deformable bodies

    NASA Astrophysics Data System (ADS)

    De Rosis, Alessandro

    2014-11-01

    In this paper, a numerical model to simulate a multiphase flow interacting with deformable solid bodies is proposed. The fluid domain is modeled through the lattice Boltzmann method and the Shan-Chen model is adopted to handle the multiphase feature. The interaction of the flow with immersed solid bodies is accounted for by using the Immersed Boundary method. Corotational beam finite elements are used to model the deformable bodies and non-linear structure dynamics is predicted through the Time Discontinuous Galerkin method. A numerical campaign is carried out in order to assess the effectiveness and accuracy of the proposed modeling by involving different scenarios. In particular, the model is validated by performing the bubble test and by comparing present results with the ones from a numerical commercial software. Moreover, the properties in terms of convergence are discussed. In addition, the effectiveness of the proposed methodology is evaluated by computing the error in terms of the energy that is artificially introduced in the system at the fluid-solid interface. Present findings show that the proposed approach is robust, accurate and suitable of being applied to a lot of practical applications involving the interaction between multiphase flows and deformable solid bodies.

  14. Hydrodynamic models for slurry bubble column reactors. Seventh technical progress report, January--March 1996

    SciTech Connect

    Gidaspow, D.

    1996-04-01

    The objective of this investigation is to convert our ``learning gas solid-liquid`` fluidization model into a predictive design model. The IIT hydrodynamic model computes the phase velocities and the volume fractions of gas, liquid and particulate phase. Model verification involves a comparison of these computed velocities and volume fractions to experimental values. A hydrodynamic model for multiphase flows, based on the principles of mass, momentum and energy conservation for each phase, was developed and applied to model gas-liquid, gas-liquid-solid fluidization and gas-solid-solid separation. To simulate the industrial slurry bubble column reactors, a computer program based on the hydrodynamic model was written with modules for chemical reactions (e.g. the synthesis of methanol), phase changes and heat exchangers. In the simulations of gas-liquid two phases flow system, the gas hold-ups, computed with a variety of operating conditions such as temperature, pressure, gas and liquid velocities, agree well with the measurements obtained at Air Products` pilot plant. The hydrodynamic model has more flexible features than the previous empirical correlations in predicting the gas hold-up of gas-liquid two-phase flow systems. In the simulations of gas-liquid-solid bubble column reactors with and without slurry circulation, the code computes volume fractions, temperatures and velocity distributions for the gas, the liquid and the solid phases, as well as concentration distributions for the species (CO, H{sub 2}, CH{sub 3}0H, ... ), after startup from a certain initial state. A kinetic theory approach is used to compute a solid viscosity due to particle collisions. Solid motion and gas-liquid-solid mixing are observed on a color PCSHOW movie made from computed time series data. The steady state and time average catalyst concentration profiles, the slurry height and the rates of methanol production agree well with the measurements obtained at an Air Products` pilot plant.

  15. Lattice Boltzmann Simulation of Multiphase Transport in Nanostructured PEM Fuel Cells

    NASA Astrophysics Data System (ADS)

    Stiles, Christopher D.

    As the fossil fuel crisis becomes more critical, it is imperative to develop renewable sources of power generation. Polymer electrolyte membrane (PEM) fuel cells are considered a viable option. However, the cost of the platinum catalyst has hindered their commercialization. PEM fuel cells with platinum loading of >0.4 mg cm2 are common. Efforts towards further reducing this loading are currently underway utilizing nanostructured electrodes. A consequence of increased platinum utilization per unit area and thinner nanostructured electrodes is flooding, which is detrimental to fuel cell performance. Flooding causes a two-fold impact on cell performance: a drop in cell voltage and a rise in parasitic pumping power to overcome the increased pressure drop, which together result in a significant reduction in system efficiency. Proper water management is therefore crucial for optimum performance of the fuel cell and also for enhancing membrane durability. The goal of this thesis is to simulate the multiphase fluid transport in the nanostructured PEMFC of H2O in air with realistic density ratios. In order to pursue this goal, the ability of the pseudopotential based multiphase lattice Boltzmann method to realistically model the coexistence of the gas and liquid phases of H2O at low temperatures is explored. This method is expanded to include a gas mixture of O2 and N 2 into the multiphase H2O systems. Beginning with the examination of the phase transition region described by the current implementation of the multiphase pseudopotential lattice Boltzmann model. Following this, a modified form of the pressure term with the use of a scalar multiplier kappa for the Peng-Robinson equation of state is thoroughly investigated. This method proves to be very effective at enabling numerically stable simulations at low temperatures with large density ratios. It is found that for decreasing values of kappa, this model leads to an increase in multiphase interface thickness and a

  16. Piezoelectric properties of multiphase fibrous composites: Some theoretical results

    NASA Astrophysics Data System (ADS)

    Chen, Tungyang

    1993-11-01

    A NUMBER OF EXACT results are established for overall moduli of a piezoelectric composite medium consisting of many perfectly-bonded transversely isotropic phases of cylindrical shape and arbitrary transverse geometry. It is shown that for three-phase media of this type three universal relationships, which are independent of geometry at given volume fractions, connect six of these effective physical constants. When the phases have equal transverse rigidities in shear, exact values of certain overall moduli can be derived for multiphase systems. The explicit formulae depend solely on the concentrations and phase moduli and are unaffected by the transverse geometry of the inclusions. Specifically, seven out of a total of 10 overall moduli of a transversely isotropic composite can be found. The remaining three constants p, e15 and k11 are shown to obey an exact relation, which also applies to other physical phenomena, such as magnetoelectric and thermoelectric effects. The result is a generalization of the relations found by H ILL[J. Mech. Phys. Solids12, 199 (1964)] for purely elastic media and by Mendelson[J. Appl. Phys.46, 917 (1975)] for the purely dielectric problem.

  17. Study of hydrodynamic instabilities with a multiphase lattice Boltzmann model

    NASA Astrophysics Data System (ADS)

    Velasco, Ali Mauricio; Muñoz, José Daniel

    2015-10-01

    Rayleigh-Taylor and Kelvin-Helmholtz hydrodynamic instabilities are frequent in many natural and industrial processes, but their numerical simulation is not an easy challenge. This work simulates both instabilities by using a lattice Boltzmann model on multiphase fluids at a liquid-vapour interface, instead of multicomponent systems like the oil-water one. The model, proposed by He, Chen and Zhang (1999) [1] was modified to increase the precision by computing the pressure gradients with a higher order, as proposed by McCracken and Abraham (2005) [2]. The resulting model correctly simulates both instabilities by using almost the same parameter set. It also reproduces the relation γ ∝√{ A} between the growing rate γ of the Rayleigh-Taylor instability and the relative density difference between the fluids (known as the Atwood number A), but including also deviations observed in experiments at low density differences. The results show that the implemented model is a useful tool for the study of hydrodynamic instabilities, drawing a sharp interface and exhibiting numerical stability for moderately high Reynolds numbers.

  18. MSTS - Multiphase Subsurface Transport Simulator theory manual

    SciTech Connect

    White, M.D.; Nichols, W.E.

    1993-05-01

    The US Department of Energy, through the Yucca Mountain Site Characterization Project Office, has designated the Yucca Mountain site in Nevada for detailed study as the candidate US geologic repository for spent nuclear fuel and high-level radioactive waste. Site characterization will determine the suitability of the Yucca Mountain site for the potential waste repository. If the site is determined suitable, subsequent studies and characterization will be conducted to obtain authorization from the Nuclear Regulatory Commission to construct the potential waste repository. A principal component of the characterization and licensing processes involves numerically predicting the thermal and hydrologic response of the subsurface environment of the Yucca Mountain site to the potential repository over a 10,000-year period. The thermal and hydrologic response of the subsurface environment to the repository is anticipated to include complex processes of countercurrent vapor and liquid migration, multiple-phase heat transfer, multiple-phase transport, and geochemical reactions. Numerical simulators based on mathematical descriptions of these subsurface phenomena are required to make numerical predictions of the thermal and hydrologic response of the Yucca Mountain subsurface environment The engineering simulator called the Multiphase Subsurface Transport Simulator (MSTS) was developed at the request of the Yucca Mountain Site Characterization Project Office to produce numerical predictions of subsurface flow and transport phenomena at the potential Yucca Mountain site. This document delineates the design architecture and describes the specific computational algorithms that compose MSTS. Details for using MSTS and sample problems are given in the {open_quotes}User`s Guide and Reference{close_quotes} companion document.

  19. Viscous and gravitational fingering in multiphase compositional and compressible flow

    NASA Astrophysics Data System (ADS)

    Moortgat, Joachim

    2016-03-01

    Viscous and gravitational fingering refer to flow instabilities in porous media that are triggered by adverse mobility or density ratios, respectively. These instabilities have been studied extensively in the past for (1) single-phase flow (e.g., contaminant transport in groundwater, first-contact-miscible displacement of oil by gas in hydrocarbon production), and (2) multi-phase immiscible and incompressible flow (e.g., water-alternating-gas (WAG) injection in oil reservoirs). Fingering in multiphase compositional and compressible flow has received much less attention, perhaps due to its high computational complexity. However, many important subsurface processes involve multiple phases that exchange species. Examples are carbon sequestration in saline aquifers and enhanced oil recovery (EOR) by gas or WAG injection below the minimum miscibility pressure. In multiphase flow, relative permeabilities affect the mobility contrast for a given viscosity ratio. Phase behavior can also change local fluid properties, which can either enhance or mitigate viscous and gravitational instabilities. This work presents a detailed study of fingering behavior in compositional multiphase flow in two and three dimensions and considers the effects of (1) Fickian diffusion, (2) mechanical dispersion, (3) flow rates, (4) domain size and geometry, (5) formation heterogeneities, (6) gravity, and (7) relative permeabilities. Results show that fingering in compositional multiphase flow is profoundly different from miscible conditions and upscaling techniques used for the latter case are unlikely to be generalizable to the former.

  20. COMPUTATIONAL AND EXPERIMENTAL MODELING OF SLURRY BUBBLE COLUMN REACTORS

    SciTech Connect

    Paul C.K. Lam; Isaac K. Gamwo; Dimitri Gidaspow

    2002-05-01

    The objective of this study was to develop a predictive experimentally verified computational fluid dynamics (CFD) model for gas-liquid-solid flow. A three dimensional transient computer code for the coupled Navier-Stokes equations for each phase was developed and is appended in this report. The principal input into the model is the viscosity of the particulate phase which was determined from a measurement of the random kinetic energy of the 800 micron glass beads and a Brookfield viscometer. The details are presented in the attached paper titled ''CFD Simulation of Flow and Turbulence in a Slurry Bubble Column''. This phase of the work is in press in a referred journal (AIChE Journal, 2002) and was presented at the Fourth International Conference on Multiphase Flow (ICMF 2001) in New Orleans, May 27-June 1, 2001 (Paper No. 909). The computed time averaged particle velocities and concentrations agree with Particle Image Velocimetry (PIV) measurements of velocities and concentrations, obtained using a combination of gamma-ray and X-ray densitometers, in a slurry bubble column, operated in the bubbly-coalesced fluidization regime with continuous flow of water. Both the experiment and the simulation show a down-flow of particles in the center of the column and up-flow near the walls and nearly uniform particle concentration. Normal and shear Reynolds stresses were constructed from the computed instantaneous particle velocities. The PIV measurement and the simulation produced instantaneous particle velocities. The PIV measurement and the simulation produced similar nearly flat horizontal profiles of turbulent kinetic energy of particles. To better understand turbulence we studied fluidization in a liquid-solid bed. This work was also presented at the Fourth International Conference on Multiphase Flow (ICMF 2001, Paper No. 910). To understand turbulence in risers, measurements were done in the IIT riser with 530 micron glass beads using a PIV technique. This report

  1. 9. Detail view of columns on first floor. This row ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    9. Detail view of columns on first floor. This row of columns indicates the former location of the exterior mill wall before World War II era expansion. The unusual column and beam connection was a key part of the mill structural system patented by Providence, Rhode Island engineers Charles Praray and Charles Makepeace in 1894. Each column was originally located in the apex of triangular window bay, but not connected to the exterior wall. Modifications on the right side of each column support the beams of the addition. - Dixie Cotton Mill, 710 Greenville Street, La Grange, Troup County, GA

  2. HEAVY OIL PROCESS MONITOR: AUTOMATED ON-COLUMN ASPHALTENE PRECIPITATION AND RE-DISSOLUTION

    SciTech Connect

    John F. Schabron; Joseph F. Rovani Jr; Mark Sanderson

    2006-06-01

    About 37-50% (w/w) of the heptane asphaltenes from unpyrolyzed residua dissolve in cyclohexane. As pyrolysis progresses, this number decrease to below 15% as coke and toluene insoluble pre-coke materials appear. This solubility measurement can be used after coke begins to form, unlike the flocculation titration, which cannot be applied to multi-phase systems. Currently, the procedure for the isolation of heptane asphaltenes and the determination of the amount of asphaltenes soluble in cyclohexane spans three days. A more rapid method to measure asphaltene solubility was explored using a novel on-column asphaltene precipitation and re-dissolution technique. This was automated using high performance liquid chromatography (HPLC) equipment with a step gradient sequence using the solvents: heptane, cyclohexane, toluene:methanol (98:2). Results for four series of original and pyrolyzed residua were compared with data from the gravimetric method. The measurement time was reduced from three days to forty minutes. The separation was expanded further with the use of four solvents: heptane, cyclohexane, toluene, and cyclohexanone or methylene chloride. This provides a fourth peak which represents the most polar components, in the oil.

  3. Effectiveness of a computer-aided neuroanatomy program for entry-level physical therapy students: anatomy and clinical examination of the dorsal column-medial lemniscal system.

    PubMed

    McKeough, D Michael; Mattern-Baxter, Katrin; Barakatt, Edward

    2010-01-01

    The purpose of this study was to determine if a computer-aided instruction learning module improves students' knowledge of the neuroanatomy/physiology and clinical examination of the dorsal column-medial lemniscal (DCML) system. Sixty-one physical therapy students enrolled in a clinical neurology course in entry-level PT educational programs at two universities participated in the study. Students from University-1 (U1;) had not had a previous neuroanatomy course, while students from University-2 (U2;) had taken a neuroanatomy course in the previous semester. Before and after working with the learning module, students took a paper-and-pencil test on the neuroanatomy/physiology and clinical examination of the DCML system. Kruskal-Wallis one-way ANOVA and Mann-Whitney tests were used to determine if differences existed between neuroanatomy/physiology examination scores and clinical examination scores before and after taking the learning module, and between student groups based on university attended. For students from U1, neuroanatomy/physiology post-test scores improved significantly over pre-test scores (p < 0.001), while post-test scores of students from U2 did not (p = 0.60). Neuroanatomy/physiology pre-test scores from U2 were significantly better than those from U1 (p < 0.001); there was no significant difference in post-test scores (p = 0.062). Clinical examination pre-test and post-test scores from U2 were significantly better than those from U1 (p < 0.001). Clinical examination post-test scores improved significantly from the pre-test scores for both U1 (p < 0.001) and U2 (p < 0.001).

  4. A Cell-Centered Multiphase ALE Scheme With Structural Coupling

    SciTech Connect

    Dunn, Timothy Alan

    2012-04-16

    A novel computational scheme has been developed for simulating compressible multiphase flows interacting with solid structures. The multiphase fluid is computed using a Godunov-type finite-volume method. This has been extended to allow computations on moving meshes using a direct arbitrary-Eulerian- Lagrangian (ALE) scheme. The method has been implemented within a Lagrangian hydrocode, which allows modeling the interaction with Lagrangian structural regions. Although the above scheme is general enough for use on many applications, the ultimate goal of the research is the simulation of heterogeneous energetic material, such as explosives or propellants. The method is powerful enough for application to all stages of the problem, including the initial burning of the material, the propagation of blast waves, and interaction with surrounding structures. The method has been tested on a number of canonical multiphase tests as well as fluid-structure interaction problems.

  5. Investigation on the gas pockets in a rotodynamic multiphase pump

    NASA Astrophysics Data System (ADS)

    Zhang, J. Y.; Li, Y. J.; Cai, S. J.; Zhu, H. W.; Zhang, Y. X.

    2016-05-01

    The appearance of gas pockets has an obvious impact on the performance of the rotodynamic multiphase pump. In order to study the formation of gas pockets in the pump and its effects on pump's performance, the unsteady numerical simulation and the visualization experiments were done to investigate gas pockets in a three-stage rotodynamic multiphase pump developed by authors. Meanwhile, the mixture of water and air was selected as the medium. According to the distributions of pressure, gas volume fraction and velocity vector in three compression cells in unsteady flow process, the process of the formation of gas pockets in the pump were analysed generally. The visualization experiments were used to verify the validity of the numerical simulation. The results will be benefit for the hydraulic design of the compression cell of rotodynamic multiphase pump.

  6. Multi-residue analytical method for the determination of endocrine disruptors and related compounds in river and waste water using dual column liquid chromatography switching system coupled to mass spectrometry.

    PubMed

    Gorga, Marina; Petrovic, Mira; Barceló, Damià

    2013-06-21

    The present study describes a novel, fully automated method, based on column switching using EQuan™ columns for an integrated sample preconcentration and liquid chromatography coupled to tandem mass spectrometry (LC-LC-MS/MS). The method allows the unequivocal identification and quantification of the most relevant environmental endocrine disruptors compounds (EDCs) and compounds suspected to be EDCs, such as natural and synthetic estrogens and their conjugates, antimicrobials, parabens, bisphenol A, alkylphenolic compounds, benzotriazoles, and organophosphorus flame retardants, in surface river water and wastewater samples. Applying this technique, water samples were directly injected into the chromatographic system and the target compounds were concentrated into the loading column. Thereafter, the analytes were transferred into the analytical column for subsequent detection by MS-MS (QqQ). A comparative study employing three types of columns, with different chemical modifications, was performed in order to determine the optimal column that allowed maximum retention and subsequent elution of the analytes. Using this new optimized methodology a fast and easy online methodology for the analysis of EDCs in surface river water and wastewater with low limits of quantification (LOQ) was obtained. LOQs ranged from 0.008 to 1.54 ng/L for surface river water and from 0.178/0.364 to 12.5/25.0 ng/L (except for alkylphenol monoethoxylates) for effluent/influent waste water. Moreover, employing approximately 1h, a complete analysis was performed which was significant improvement in comparison to other methods reported previously. This method was used to track the presence and fate of target compounds in the Ebro River which is the most important river in Spain whose intensive agricultural and industrial activities concentrate mainly close to the main cities in the basin, deteriorating soil and water quality.

  7. Multi-phase SPH modelling of violent hydrodynamics on GPUs

    NASA Astrophysics Data System (ADS)

    Mokos, Athanasios; Rogers, Benedict D.; Stansby, Peter K.; Domínguez, José M.

    2015-11-01

    This paper presents the acceleration of multi-phase smoothed particle hydrodynamics (SPH) using a graphics processing unit (GPU) enabling large numbers of particles (10-20 million) to be simulated on just a single GPU card. With novel hardware architectures such as a GPU, the optimum approach to implement a multi-phase scheme presents some new challenges. Many more particles must be included in the calculation and there are very different speeds of sound in each phase with the largest speed of sound determining the time step. This requires efficient computation. To take full advantage of the hardware acceleration provided by a single GPU for a multi-phase simulation, four different algorithms are investigated: conditional statements, binary operators, separate particle lists and an intermediate global function. Runtime results show that the optimum approach needs to employ separate cell and neighbour lists for each phase. The profiler shows that this approach leads to a reduction in both memory transactions and arithmetic operations giving significant runtime gains. The four different algorithms are compared to the efficiency of the optimised single-phase GPU code, DualSPHysics, for 2-D and 3-D simulations which indicate that the multi-phase functionality has a significant computational overhead. A comparison with an optimised CPU code shows a speed up of an order of magnitude over an OpenMP simulation with 8 threads and two orders of magnitude over a single thread simulation. A demonstration of the multi-phase SPH GPU code is provided by a 3-D dam break case impacting an obstacle. This shows better agreement with experimental results than an equivalent single-phase code. The multi-phase GPU code enables a convergence study to be undertaken on a single GPU with a large number of particles that otherwise would have required large high performance computing resources.

  8. National laboratories` capabilities summaries for the DOE Virtual Center for Multiphase Dynamics (VCMD)

    SciTech Connect

    Joyce, E.L.

    1997-03-01

    The Virtual Center For Multiphase Dynamics (VCMD) integrates and develops the resources of industry, government, academia, and professional societies to enable reliable analysis in multiphase computational fluid dynamics. The primary means of the VCMD focus will be by the creation, support, and validation of a computerized simulation capability for multiphase flow and multiphase flow applications. This paper briefly describes the capabilities of the National Laboratories in this effort.

  9. Evaluation of Two Lattice Boltzmann Models for Multiphase Flows

    NASA Astrophysics Data System (ADS)

    Hou, Shuling; Shan, Xiaowen; Zou, Qisu; Doolen, Gary D.; Soll, Wendy E.

    1997-12-01

    Two lattice Boltzmann models for multiphase flows, the immiscible fluid model proposed by Rothman and Keller (R-K) and the multicomponent nonideal gas lattice Boltzmann model by Shan and Chen (S-C), are studied numerically to compare their abilities to simulate the physics of multiphase flows. The test problem is the simulation of a static bubble. Isotropy, strength of surface tension, thickness of the interface, spurious currents, Laplace's law, and steadiness of the bubble are examined. The results show that the S-C model is a major improvement over the R-K model.

  10. Multiphasic acute disseminated encephalomyelitis associated with atypical rubella virus infection.

    PubMed

    Shinoda, Koji; Asahara, Hideaki; Uehara, Taira; Miyoshi, Katsue; Suzuki, Satoshi O; Iwaki, Toru; Kira, Jun-ichi

    2015-02-01

    We report the first case of an occurrence of multiphasic acute disseminated encephalomyelitis (ADEM) associated with atypical rubella virus infection with no rash and long-term increased titers of serum anti-rubella IgM in a 17-year-old male who had no history of rubella vaccination. He suffered from at least six clinical exacerbations with disseminated hyperintense lesions on FLAIR MR images during the course of 18 months. Repeated methylprednisolone pulse therapy and intravenous immunoglobulin therapy resolved the exacerbations. In patients with multiphasic ADEM of unknown etiology, clinicians should also consider the possibility of preceding infection with rubella virus.

  11. Novel Hierarchical Fall Detection Algorithm Using a Multiphase Fall Model

    PubMed Central

    Hsieh, Chia-Yeh; Liu, Kai-Chun; Huang, Chih-Ning; Chu, Woei-Chyn; Chan, Chia-Tai

    2017-01-01

    Falls are the primary cause of accidents for the elderly in the living environment. Reducing hazards in the living environment and performing exercises for training balance and muscles are the common strategies for fall prevention. However, falls cannot be avoided completely; fall detection provides an alarm that can decrease injuries or death caused by the lack of rescue. The automatic fall detection system has opportunities to provide real-time emergency alarms for improving the safety and quality of home healthcare services. Two common technical challenges are also tackled in order to provide a reliable fall detection algorithm, including variability and ambiguity. We propose a novel hierarchical fall detection algorithm involving threshold-based and knowledge-based approaches to detect a fall event. The threshold-based approach efficiently supports the detection and identification of fall events from continuous sensor data. A multiphase fall model is utilized, including free fall, impact, and rest phases for the knowledge-based approach, which identifies fall events and has the potential to deal with the aforementioned technical challenges of a fall detection system. Seven kinds of falls and seven types of daily activities arranged in an experiment are used to explore the performance of the proposed fall detection algorithm. The overall performances of the sensitivity, specificity, precision, and accuracy using a knowledge-based algorithm are 99.79%, 98.74%, 99.05% and 99.33%, respectively. The results show that the proposed novel hierarchical fall detection algorithm can cope with the variability and ambiguity of the technical challenges and fulfill the reliability, adaptability, and flexibility requirements of an automatic fall detection system with respect to the individual differences. PMID:28208694

  12. Topographic organization of the orientation column system in large flat-mounts of the cat visual cortex: a 2-deoxyglucose study.

    PubMed

    Löwel, S; Freeman, B; Singer, W

    1987-01-15

    We developed a flat-mount technique in order to visualize, without additional reconstruction, the system of orientation columns in the cat visual cortex by using 2-deoxyglucose-autoradiography. Experimental animals were injected with 2-deoxyglucose and then stimulated for 45-60 minutes either with vertical or horizontal or oblique gratings alone or with vertical and horizontal gratings presented in alternation. In both areas 17 and 18 stimulation with either vertical or horizontal or oblique stripes produced similar and highly ordered patterns of parallel bands of increased 2-deoxyglucose uptake that were perpendicular to the boundaries of the areas. In area 17 they occasionally extended without interruption from the 17/18 border on the top of the lateral gyrus to the monocular segment in the splenial sulcus. Superposition of serial sections revealed that these bands were present in all cortical layers and in precise register along lines orthogonal to the lamination. The center-to-center spacing of the bands was 1.0-1.1 mm in area 17 and 1.2-1.4 mm in area 18. Stimulation with alternating vertical and horizontal contours led to a pattern the general organization of which resembled that induced by a single orientation but the spacing of which was reduced by a factor of 0.5. This strongly supports the concept that orientation is mapped in a system of parallel bands and argues against a recently formulated hypothesis that iso-orientation bands extend like spokes from centers that lack orientation selectivity (Braitenberg and Braitenberg, Biol. Cybern. 33:179-186, '79). Another characteristic feature, revealed by the flat-mount technique, was a periodic variation of 2-deoxyglucose uptake along the bands that gave them a beaded appearance. The mean center-to-center distance between adjacent beads on the same band was in the range of 0.9-1.2 mm and remained unchanged when horizontal and vertical gratings were presented in alternation. We propose that these beads reflect

  13. Algebraic dynamic multilevel (ADM) method for fully implicit simulations of multiphase flow in porous media

    NASA Astrophysics Data System (ADS)

    Cusini, Matteo; van Kruijsdijk, Cor; Hajibeygi, Hadi

    2016-06-01

    This paper presents the development of an algebraic dynamic multilevel method (ADM) for fully implicit simulations of multiphase flow in homogeneous and heterogeneous porous media. Built on the fine-scale fully implicit (FIM) discrete system, ADM constructs a multilevel FIM system describing the coupled process on a dynamically defined grid of hierarchical nested topology. The multilevel adaptive resolution is determined at each time step on the basis of an error criterion. Once the grid resolution is established, ADM employs sequences of restriction and prolongation operators in order to map the FIM system across the considered resolutions. Several choices can be considered for prolongation (interpolation) operators, e.g., constant, bilinear and multiscale basis functions, all of which form partition of unity. The adaptive multilevel restriction operators, on the other hand, are constructed using a finite-volume scheme. This ensures mass conservation of the ADM solutions, and as such, the stability and accuracy of the simulations with multiphase transport. For several homogeneous and heterogeneous test cases, it is shown that ADM applies only a small fraction of the full FIM fine-scale grid cells in order to provide accurate solutions. The sensitivity of the solutions with respect to the employed fraction of grid cells (determined automatically based on the threshold value of the error criterion) is investigated for all test cases. ADM is a significant step forward in the application of dynamic local grid refinement methods, in the sense that it is algebraic, allows for systematic mapping across different scales, and applicable to heterogeneous test cases without any upscaling of fine-scale high resolution quantities. It also develops a novel multilevel multiscale method for FIM multiphase flow simulations in natural subsurface formations.

  14. The lateral column lengthening and medial column stabilization procedures.

    PubMed

    Chi, T D; Toolan, B C; Sangeorzan, B J; Hansen, S T

    1999-08-01

    The results of medial column stabilization, lateral column lengthening, and combined medial and lateral procedures were reviewed in the treatment of adult acquired flatfoot secondary to posterior tibialis tendon insufficiency. All bony procedures were accompanied by transfer of the flexor digitorum longus tendon to the medial cuneiform or stump of the posterior tibialis tendon and tendoachilles lengthening or gastrocnemius recession. Medial column fusion was performed for naviculocuneiform and cuneiform first metatarsal sag; lateral column lengthening was performed for calcaneovalgus deformity with a flat pitch angle; and combined procedures were performed for complex combined deformities. At 1 to 4 year followup of 65 feet, 88% of the feet that had lateral column lengthening, 80% that had medial column stabilization, and 88% of the feet that had medial and lateral procedures had a decrease in pain or were pain free. The lateral talar first metatarsal angle improved by 16 degrees in the patients in the lateral column lengthening group, 20 degrees in the patients in the medial column stabilization group, and 24 degrees in the patients in the combined medial and lateral procedures group. The anteroposterior talonavicular coverage angle improved by 14 degrees in the patients in the lateral column lengthening group, 10 degrees in the patients in the medial column stabilization group, and 14 degrees in the patients in the combined medial and lateral procedures group. These techniques effectively correct deformity without disrupting the essential joints of the hindfoot and midfoot.

  15. Heat Transfer Analysis for a Fixed CST Column

    SciTech Connect

    Lee, S.Y.

    2004-02-19

    In support of a small column ion exchange (SCIX) process for the Savannah River Site waste processing program, a transient two-dimensional heat transfer model that includes the conduction process neglecting the convection cooling mechanism inside the crystalline silicotitanate (CST) column has been constructed and heat transfer calculations made for the present design configurations. For this situation, a no process flow condition through the column was assumed as one of the reference conditions for the simulation of a loss-of-flow accident. A series of the modeling calculations has been performed using a computational heat transfer approach. Results for the baseline model indicate that transit times to reach 130 degrees Celsius maximum temperature of the CST-salt solution column are about 96 hours when the 20-in CST column with 300 Ci/liter heat generation source and 25 degrees Celsius initial column temperature is cooled by natural convection of external air as a primary heat transfer mechanism. The modeling results for the 28-in column equipped with water jacket systems on the external wall surface of the column and water coolant pipe at the center of the CST column demonstrate that the column loaded with 300 Ci/liter heat source can be maintained non-boiling indefinitely. Sensitivity calculations for several alternate column sizes, heat loads of the packed column, engineered cooling systems, and various ambient conditions at the exterior wall of the column have been performed under the reference conditions of the CST-salt solution to assess the impact of those parameters on the peak temperatures of the packed column for a given transient time. The results indicate that a water-coolant pipe at the center of the CST column filled with salt solution is the most effective one among the potential design parameters related to the thermal energy dissipation of decay heat load. It is noted that the cooling mechanism at the wall boundary of the column has significant

  16. Utility of a column-free cell sorting system for separation of plasma cells in multiple myeloma FISH testing in clinical laboratories.

    PubMed

    Shetty, Shashirekha; Siady, Marion; Mallempati, Kalyan C; Wilson, Andrew; Poarch, Jeff; Chandler, Brandon; Gray, Judy; Salama, Mohamed E

    2012-03-01

    Targeted FISH analysis is an essential component of the management of plasma cell myeloma for identification of cytogenetic abnormalities. The purpose of this study was to evaluate the column-free method, RoboSep® (RS), for sorting CD138-expressing cells in bone marrow aspirates. Comparative analysis of column-based and RS methodologies was carried out on 54 paired bone marrow aspirate validation samples from patients undergoing work-up for plasma cell dyscrasia. Abnormalities detected by FISH analysis using an IGH@/CCND1 probe set were seen in 54% with RS, and 44% with column-based. We found a statistically significant difference between the yield of abnormalities detected in paired positive cases (p = 0.0001). An additional 183 consecutive post-validation samples sorted by RS showed recurrent genetic abnormalities in 85/120 (71%) of successfully sorted samples with ≥ 1% plasma cells but in none of 63 samples in which FISH analysis was completed on samples that could not be sorted due to insufficient plasma cells upon cell sorting. The column-free method successfully sorted PC, when present in ≥ 1% of cells, for detection of abnormalities by FISH. Furthermore, our data suggest that FISH analysis should not be performed on samples with an inadequate yield at the cell selection step.

  17. KINEMATIC MODELING OF MULTIPHASE SOLUTE TRANSPORT IN THE VADOSE ZONE

    EPA Science Inventory

    The goal of this research was the development of a computationally efficient simulation model for multiphase flow of organic hazardous waste constituents in the shallow soil environment. Such a model is appropriate for investigation of fate and transport of organic chemicals intr...

  18. Hydrodynamical Coupling of Mass and Momentum in Multiphase Galactic Winds

    NASA Astrophysics Data System (ADS)

    Schneider, Evan E.; Robertson, Brant E.

    2017-01-01

    Using a set of high-resolution hydrodynamical simulations run with the Cholla code, we investigate how mass and momentum couple to the multiphase components of galactic winds. The simulations model the interaction between a hot wind driven by supernova explosions and a cooler, denser cloud of interstellar or circumgalactic media. By resolving scales of {{Δ }}x< 0.1 pc over > 100 pc distances, our calculations capture how the cloud disruption leads to a distribution of densities and temperatures in the resulting multiphase outflow and quantify the mass and momentum associated with each phase. We find that the multiphase wind contains comparable mass and momenta in phases over a wide range of densities and temperatures extending from the hot wind (n≈ {10}-2.5 {{cm}}-3, T≈ {10}6.5 K) to the coldest components (n≈ {10}2 {{cm}}-3, T≈ {10}2 K). We further find that the momentum distributes roughly in proportion to the mass in each phase, and the mass loading of the hot phase by the destruction of cold, dense material is an efficient process. These results provide new insight into the physical origin of observed multiphase galactic outflows and inform galaxy formation models that include coarser treatments of galactic winds. Our results confirm that cool gas observed in outflows at large distances from the galaxy (≳ 1 kpc) likely does not originate through the entrainment of cold material near the central starburst.

  19. 9th International Conference on Multiphase Flow (ICMF 2016)

    DTIC Science & Technology

    2016-08-12

    International Conference on Multiphase Flows Event Dates: May 22-27, 2016 Event City and Country: Florence, Italy Grantee (Name and Contact ...and Contact Information): Alfredo Soldati (Tel +39 0432 558020, Fax +39 0432 558027, E-mail: soldati@uniud.it) ONRG CSP Grant Number: N62909-16-1

  20. Automated Design of Multiphase Space Missions Using Hybrid Optimal Control

    ERIC Educational Resources Information Center

    Chilan, Christian Miguel

    2009-01-01

    A modern space mission is assembled from multiple phases or events such as impulsive maneuvers, coast arcs, thrust arcs and planetary flybys. Traditionally, a mission planner would resort to intuition and experience to develop a sequence of events for the multiphase mission and to find the space trajectory that minimizes propellant use by solving…

  1. A New Multiphase Equation of State for Composition B

    SciTech Connect

    Coe, Joshua Damon; Margevicius, Madeline Alma

    2016-07-25

    We describe the construction of a complete equation of state for the high explosive Composition B in its unreacted (inert) form, as well as chemical equilibrium calculations of its detonation products. The multiphase reactant EOS is of SESAME type, and was calibrated to ambient thermal and mechanical data, the shock initiation experiments of Dattelbaum, et al., and the melt line of trinitrotoluene (TNT).

  2. Sampling device for withdrawing a representative sample from single and multi-phase flows

    DOEpatents

    Apley, Walter J.; Cliff, William C.; Creer, James M.

    1984-01-01

    A fluid stream sampling device has been developed for the purpose of obtaining a representative sample from a single or multi-phase fluid flow. This objective is carried out by means of a probe which may be inserted into the fluid stream. Individual samples are withdrawn from the fluid flow by sampling ports with particular spacings, and the sampling parts are coupled to various analytical systems for characterization of the physical, thermal, and chemical properties of the fluid flow as a whole and also individually.

  3. Ginzburg-Landau-type multiphase field model for competing fcc and bcc nucleation.

    PubMed

    Tóth, G I; Morris, J R; Gránásy, L

    2011-01-28

    We address crystal nucleation and fcc-bcc phase selection in alloys using a multiphase field model that relies on Ginzburg-Landau free energies of the liquid-fcc, liquid-bcc, and fcc-bcc subsystems, and determine the properties of the nuclei as a function of composition, temperature, and structure. With a realistic choice for the free energy of the fcc-bcc interface, the model predicts well the fcc-bcc phase-selection boundary in the Fe-Ni system.

  4. On the inclusion of the interfacial area between phases in the physical and mathematical description of subsurface multiphase flow. 1998 annual progress report

    SciTech Connect

    Gray, W.G.; Tompson, A.; Soll, W.E.

    1998-06-01

    'Improved capabilities for modeling multiphase flow in the subsurface requires that several aspects of the system which impact the flow and transport processes be more properly accounted for. A distinguishing feature of multiphase flow in comparison to single phase flow is the existence of interfaces between fluids. At the microscopic (pore) scale, these interfaces are known to influence system behavior by supporting non-zero stresses such that the pressures in adjacent phases are not equal. In problems of interphase transport at the macroscopic (core) scale, knowledge of the total amount of interfacial area in the system provides a clue to the effectiveness of the communication between phases. Although interfacial processes are central to multiphase flow physics, their treatment in traditional porous-media theories has been implicit rather than explicit; and no attempts have been made to systematically account for the evolution of the interfacial area in dynamic systems or to include the dependence of constitutive functions, such as capillary pressure, on the interfacial area. This project implements a three-pronged approach to assessing the importance of various features of multiphase flow to its description. The research contributes to the improved understanding and precise physical description of multiphase subsurface flow by combining: (1) theoretical derivation of equations, (2) lattice Boltzmann modeling of hydrodynamics to identify characteristics and parameters, and (3) solution of the field-scale equations using a discrete numerical method to assess the advantages and disadvantages of the complete theory. This approach includes both fundamental scientific inquiry and a path for inclusion of the scientific results obtained in a technical tool that will improve assessment capabilities for multiphase flow situations that have arisen due to the introduction of organic materials in the natural environment. This report summarizes work after 1.5 years of a 3

  5. TOUGH2: A general-purpose numerical simulator for multiphase nonisothermal flows

    SciTech Connect

    Pruess, K.

    1991-06-01

    Numerical simulators for multiphase fluid and heat flows in permeable media have been under development at Lawrence Berkeley Laboratory for more than 10 yr. Real geofluids contain noncondensible gases and dissolved solids in addition to water, and the desire to model such `compositional` systems led to the development of a flexible multicomponent, multiphase simulation architecture known as MULKOM. The design of MULKOM was based on the recognition that the mass-and energy-balance equations for multiphase fluid and heat flows in multicomponent systems have the same mathematical form, regardless of the number and nature of fluid components and phases present. Application of MULKOM to different fluid mixtures, such as water and air, or water, oil, and gas, is possible by means of appropriate `equation-of-state` (EOS) modules, which provide all thermophysical and transport parameters of the fluid mixture and the permeable medium as a function of a suitable set of primary thermodynamic variables. Investigations of thermal and hydrologic effects from emplacement of heat-generating nuclear wastes into partially water-saturated formations prompted the development and release of a specialized version of MULKOM for nonisothermal flow of water and air, named TOUGH. TOUGH is an acronym for `transport of unsaturated groundwater and heat` and is also an allusion to the tuff formations at Yucca Mountain, Nevada. The TOUGH2 code is intended to supersede TOUGH. It offers all the capabilities of TOUGH and includes a considerably more general subset of MULKOM modules with added capabilities. The paper briefly describes the simulation methodology and user features.

  6. Multiphasic dynamics of phosphatidylinositol 4-phosphate during phagocytosis

    PubMed Central

    Levin, Roni; Hammond, Gerald R. V.; Balla, Tamas; De Camilli, Pietro; Fairn, Gregory D.; Grinstein, Sergio

    2017-01-01

    We analyzed the distribution, fate, and functional role of phosphatidylinositol 4-phosphate (PtdIns4P) during phagosome formation and maturation. To this end, we used genetically encoded probes consisting of the PtdIns4P-binding domain of the bacterial effector SidM. PtdIns4P was found to undergo complex, multiphasic changes during phagocytosis. The phosphoinositide, which is present in the plasmalemma before engagement of the target particle, is transiently enriched in the phagosomal cup. Soon after the phagosome seals, PtdIns4P levels drop precipitously due to the hydrolytic activity of Sac2 and phospholipase C, becoming undetectable for ∼10 min. PtdIns4P disappearance coincides with the emergence of phagosomal PtdIns3P. Conversely, the disappearance of PtdIns3P that signals the transition from early to late phagosomes is accompanied by resurgence of PtdIns4P, which is associated with the recruitment of phosphatidylinositol 4-kinase 2A. The reacquisition of PtdIns4P can be prevented by silencing expression of the kinase and can be counteracted by recruitment of a 4-phosphatase with a heterodimerization system. Using these approaches, we found that the secondary accumulation of PtdIns4P is required for proper phagosomal acidification. Defective acidification may be caused by impaired recruitment of Rab7 effectors, including RILP, which were shown earlier to displace phagosomes toward perinuclear lysosomes. Our results show multimodal dynamics of PtdIns4P during phagocytosis and suggest that the phosphoinositide plays important roles during the maturation of the phagosome. PMID:28035045

  7. Investigating the effect of external water on magma ascent dynamics with a new multiphase flow numerical model

    NASA Astrophysics Data System (ADS)

    De'Michieli Vitturi, M.; Neri, A.; La Spina, G.; Clarke, A. B.

    2013-12-01

    The study of deposits produced by explosive eruptions of Campi Flegrei and Vesuvio suggests that important phases of these events have been characterized by a significant interaction of magma with external water. Despite that, the influence of external water on eruption dynamics and its potential hazard have not been studied in depth. In this work we adopted a 1D non-isothermal multi-phase flow model describing the dynamics of magma ascent inside a volcanic conduit. The new model is based on the theory of thermodynamically compatible systems that allows formulation of the governing transport equations as a hyperbolic system of partial differential equations in conservative form. The model represents a significant advance with respect to previous simplified descriptions of the magma ascent dynamics in that it: 1) is capable of treating both dilute and dense flow regimes; 2) describes flow above and below the fragmentation level in a coupled and consistent way; 3) quantifies the interaction between the two phases forming the magmatic mixture (both in the bubbly-flow and gas-particle regimes) with two distinct pressures and velocities; 4) accounts for disequilibrium crystallization and degassing; 5) treats the dissolved water as a separate phase with its own equation of state and; 6) allows for instantaneous or delayed vaporization of the external water from an aquifer. Here we investigate, through a sensitivity analysis, the role of different system parameters, in particular those related to the inflow of non-magmatic volatiles, in controlling vent conditions and eruptive style for conditions representative of Plinian (e.g. Agnano Monte Spina) eruptions at Campi Flegrei. Model results show that mass flux at the vent is primarily controlled by the quantity of engulfed external water, when this inflow occurs below the fragmentation level, whereas small changes in mass flux are produced when the interaction occurs above the fragmentation level. In particular it is worth

  8. A liver registration method for segmented multi-phase CT images

    NASA Astrophysics Data System (ADS)

    Shi, Shuyue; Yuan, Rong; Sun, Zhi; Xie, Qingguo

    2015-03-01

    In order to build high quality geometric models for liver containing vascular system, multi-phase CT series used in a computer-aided diagnosis and surgical planning system aims at liver diseases have to be accurately registered. In this paper we model the segmented liver containing vascular system as a complex shape and propose a two-step registration method. Without any tree modeling for vessel this method can carry out a simultaneous registration for both liver tissue and vascular system inside. Firstly a rigid aligning using vessel as feature is applied on the complex shape model while genetic algorithm is used as the optimization method. Secondly we achieve the elastic shape registration by combine the incremental free form deformation (IFFD) with a modified iterative closest point (ICP) algorithm. Inspired by the concept of demons method, we propose to calculate a fastest diffusion vector (FDV) for each control point on the IFFD lattice to replace the points correspondence needed in ICP iterations. Under the iterative framework of the modified ICP, the optimal solution of control points' displacement in every IFFD level can be obtained efficiently. The method has been quantitatively evaluated on clinical multi-phase CT series.

  9. Multiphase flow microfluidics for the production of single or multiple emulsions for drug delivery.

    PubMed

    Zhao, Chun-Xia

    2013-11-01

    Considerable effort has been directed towards developing novel drug delivery systems. Microfluidics, capable of generating monodisperse single and multiple emulsion droplets, executing precise control and operations on these droplets, is a powerful tool for fabricating complex systems (microparticles, microcapsules, microgels) with uniform size, narrow size distribution and desired properties, which have great potential in drug delivery applications. This review presents an overview of the state-of-the-art multiphase flow microfluidics for the production of single emulsions or multiple emulsions for drug delivery. The review starts with a brief introduction of the approaches for making single and multiple emulsions, followed by presentation of some potential drug delivery systems (microparticles, microcapsules and microgels) fabricated in microfluidic devices using single or multiple emulsions as templates. The design principles, manufacturing processes and properties of these drug delivery systems are also discussed and compared. Furthermore, drug encapsulation and drug release (including passive and active controlled release) are provided and compared highlighting some key findings and insights. Finally, site-targeting delivery using multiphase flow microfluidics is also briefly introduced.

  10. Why Hexagonal Basalt Columns?

    PubMed

    Hofmann, Martin; Anderssohn, Robert; Bahr, Hans-Achim; Weiß, Hans-Jürgen; Nellesen, Jens

    2015-10-09

    Basalt columns with their preferably hexagonal cross sections are a fascinating example of pattern formation by crack propagation. Junctions of three propagating crack faces rearrange such that the initial right angles between them tend to approach 120°, which enables the cracks to form a pattern of regular hexagons. To promote understanding of the path on which the ideal configuration can be reached, two periodically repeatable models are presented here involving linear elastic fracture mechanics and applying the principle of maximum energy release rate. They describe the evolution of the crack pattern as a transition from rectangular start configuration to the hexagonal pattern. This is done analytically and by means of three-dimensional finite element simulation. The latter technique reproduces the curved crack path involved in this transition.

  11. Multi-Phase Fracture-Matrix Interactions Under Stress Changes

    SciTech Connect

    A.S. Grader; D. Elsworth; P.M. Halleck; F. Alvarao; A. Alajmi; Z. Karpyn; N. Mohammed; S. Al-Enezi

    2005-12-07

    The main objectives of this project are to quantify the changes in fracture porosity and multi-phase transport properties as a function of confining stress. These changes will be integrated into conceptual and numerical models that will improve our ability to predict and optimize fluid transport in fractured system. This report details our progress on: (a) developing the direct experimental measurements of fracture aperture and topology and fluid occupancy using high-resolution x-ray micro-tomography, (b) counter-current fluid transport between the matrix and the fracture, (c) studying the effect of confining stress on the distribution of fracture aperture and two-phase flow, and (d) characterization of shear fractures and their impact on multi-phase flow. The three-dimensional surface that describes the large-scale structure of the fracture in the porous medium can be determined using x-ray micro-tomography with significant accuracy. Several fractures have been scanned and the fracture aperture maps have been extracted. The success of the mapping of fracture aperture was followed by measuring the occupancy of the fracture by two immiscible phases, water and decane, and water and kerosene. The distribution of fracture aperture depends on the effective confining stress, on the nature of the rock, and the type and distribution of the asperities that keep the fracture open. Fracture apertures at different confining stresses were obtained by micro-tomography covering a range of about two thousand psig. Initial analysis of the data shows a significant aperture closure with increase in effective confining stress. Visual and detailed descriptions of the process are shown in the report. Both extensional and shear fractures have been considered. A series of water imbibition tests were conducted in which water was injected into a fracture and its migration into the matrix was monitored with CT and DR x-ray techniques. The objective was to understand the impact of the

  12. Rheological flow laws for multiphase magmas: An empirical approach

    NASA Astrophysics Data System (ADS)

    Pistone, Mattia; Cordonnier, Benoît; Ulmer, Peter; Caricchi, Luca

    2016-07-01

    The physical properties of magmas play a fundamental role in controlling the eruptive dynamics of volcanoes. Magmas are multiphase mixtures of crystals and gas bubbles suspended in a silicate melt and, to date, no flow laws describe their rheological behaviour. In this study we present a set of equations quantifying the flow of high-viscosity (> 105 Pa·s) silica-rich multiphase magmas, containing both crystals (24-65 vol.%) and gas bubbles (9-12 vol.%). Flow laws were obtained using deformation experiments performed at high temperature (673-1023 K) and pressure (200-250 MPa) over a range of strain-rates (5 · 10- 6 s- 1 to 4 · 10- 3 s- 1), conditions that are relevant for volcanic conduit processes of silica-rich systems ranging from crystal-rich lava domes to crystal-poor obsidian flows. We propose flow laws in which stress exponent, activation energy, and pre-exponential factor depend on a parameter that includes the volume fraction of weak phases (i.e. melt and gas bubbles) present in the magma. The bubble volume fraction has opposing effects depending on the relative crystal volume fraction: at low crystallinity bubble deformation generates gas connectivity and permeability pathways, whereas at high crystallinity bubbles do not connect and act as ;lubricant; objects during strain localisation within shear bands. We show that such difference in the evolution of texture is mainly controlled by the strain-rate (i.e. the local stress within shear bands) at which the experiments are performed, and affect the empirical parameters used for the flow laws. At low crystallinity (< 44 vol.%) we observe an increase of viscosity with increasing strain-rate, while at high crystallinity (> 44 vol.%) the viscosity decreases with increasing strain-rate. Because these behaviours are also associated with modifications of sample textures during the experiment and, thus, are not purely the result of different deformation rates, we refer to ;apparent shear-thickening; and

  13. Final Report, Distillation Column Flooding Predictor

    SciTech Connect

    George E. Dzyacky

    2003-05-31

    The Flooding Predictor is an advanced process control strategy comprising a patented pattern-recognition methodology that identifies pre-flood patterns discovered to precede flooding events in distillation columns. The grantee holds a U.S. patent on the modeling system. The technology was validated at the Separations Research Program, The University of Texas at Austin under a grant from the U. S. Department of Energy, Inventions & Innovation Program. Distillation tower flooding occurs at abnormally high vapor and/or liquid rates. The loss in tray efficiencies is attributed to unusual behavior of liquid inventories inside the column leading to conditions of flooding of the space in between trays with liquid. Depending on the severity of the flood condition, consequences range from off spec products to equipment damage and tower shutdown. This non-intrusive pattern recognition methodology, processes signal data obtained from existing column instrumentation. Once the pattern is identified empirically, it is modeled and coded into the plant's distributed control system. The control system is programmed to briefly "unload" the tower each time the pattern appears. The unloading takes the form of a momentary reduction in column severity, e.g., decrease bottom temperature, reflux or tower throughput. Unloading the tower briefly at the pre-flood state causes long-term column operation to become significantly more stable - allowing an increase in throughput and/or product purity. The technology provides a wide range of value between optimization and flooding. When a distillation column is not running at capacity, it should be run in such a way ("pushed") that optimal product purity is achieved. Additional benefits include low implementation and maintenance costs, and a high level of console operator acceptance. The previous commercial applications experienced 98% uptime over a four-year period. Further, the technology is unique in its ability to distinguish between different

  14. Buckling of a holey column.

    PubMed

    Pihler-Puzović, D; Hazel, A L; Mullin, T

    2016-09-14

    We report the results from a combined experimental and numerical investigation of buckling in a novel variant of an elastic column under axial load. We find that including a regular line of centred holes in the column can prevent conventional, global, lateral buckling. Instead, the local microstructure introduced by the holes allows the column to buckle in an entirely different, internal, mode in which the holes are compressed in alternate directions, but the column maintains the lateral reflection symmetry about its centreline. The internal buckling mode can be accommodated within a smaller external space than the global one; and it is the preferred buckling mode over an intermediate range of column lengths for sufficiently large holes. For very short or sufficiently long columns a modification of the classical, global, lateral buckling is dominant.

  15. Air separation process using packed columns for oxygen and argon recovery

    SciTech Connect

    Thorogood, R.M.; Bennett, D.L.; Allam, R.J.; Prentice, A.L.; Dawson, B.K.

    1989-10-03

    This patent describes an improvement in a process for the separation of mixtures, which comprise oxygen, nitrogen, and argon, by cryogenic distillation in an integrated multi-column distillation system of at least three distillation columns, having a higher pressure column, low pressure column and an argon sidearm column. Wherein the argon sidearm column integrally communicates with the low pressure column. Wherein each column of the integrated distillation system, a liquid phase stream and a vapor phase stream are intimately contacted thereby allowing mass transfer. The improvement involves increasing argon recovery. It comprises effectuating the intimate contact of the liquid and vapor phase streams in the low pressure column and the argon sidearm column by utilizing a structured packing.

  16. Modeling of rotating disc contactor (RDC) column

    NASA Astrophysics Data System (ADS)

    Ismail, Wan Nurul Aiffah; Zakaria, Siti Aisyah; Noor, Nor Fashihah Mohd; Sulong, Ibrahim; Arshad, Khairil Anuar

    2014-12-01

    Liquid-liquid extraction is one of the most important separation processes. Different kinds of liquid-liquid extractor such as Rotating Disc Contactor (RDC) Column being used in industries. The study of liquid-liquid extraction in an RDC column has become a very important subject to be discussed not just among chemical engineers but mathematician as well. In this research, the modeling of small diameter RDC column using the chemical system involving cumene/isobutryric asid/water are analyzed by the method of Artificial Neural Network (ANN). In the previous research, we begin the process of analyzed the data using methods of design of the experiments (DOE) to identify which factor and their interaction factor are significant and to determine the percentage of contribution of the variance for each factor. From the result obtained, we continue the research by discussed the development and validation of an artificial neural network model in estimating the concentration of continuous and concentration of dispersed outlet for an RDC column. It is expected that an efficient and reliable model will be formed to predict RDC column performance as an alternative to speed up the simulation process.

  17. "Dry-column" chromatography of plant pigments

    NASA Technical Reports Server (NTRS)

    Woeller, F. H.; Lehwalt, M. F.; Oyama, V. I.

    1973-01-01

    Separation of plant pigments which can be accomplished on thin-layer silica plates with mixture of petroleum ether, halocarbon, acetone, and polar solvent can be readily translated into dry-column technique that yields reproducible chromatograms after elution in fashion of liquid chromatography with fluorimeter as detector. Best solvent system was found to be mixture of petroleum ether, dichloromethane, acetone, and ethyl acetate.

  18. Synthesis of Ion Microbeam Column

    NASA Astrophysics Data System (ADS)

    Mui, Peter Hon-Fung

    1995-01-01

    Electrostatic lenses have traditionally been designed by analyzing and combining different electrode configurations. Computational complexity typically limits such systems to a few geometrically simple elements, where the component interactions are neglected and not exploited to combat the various aberrations. Recently, Szilagyi and Szep have demonstrated that an axially symmetric column of circular plates, with the electrode potentials optimized for focusing, can surpass the typical conventional designs by many times in performance. Following the footsteps of pioneers like Burfoot and Hawkes, we partition the plates in order to transcend the limitations set by Scherzer's theorem on the chromatic and spherical aberrations of axially symmetric structures. Two algorithms, one based upon integral asymptotics and one upon the Levinson algorithm. for Toeplitz matrix inversion, are developed to complement the charge-density method in analyzing the new column structures. Various optimization schemes are combined to avoid shallow minima at a reasonable computational cost. With each plate partitioned into four sectors, we show that the interactions between the monopole and the quadrupole components can increase the output current density by more than 400% over the axially symmetric structure. By adjusting the sector potentials, we can realize systems capable of both focusing and deflecting the beam. In comparison to some existing designs, our systems excel in both performance and compactness, sometimes by many hundred percents. We then further partition the plates to generate the "octupole" deflectors and correctors. We show that the "octupole" deflectors can drastically slow down the beam degradation with deflection distance and that the correctors can further increase the output current density by more than 300%. Finally, we apply linear system theories to the study of the first-order properties of optical systems with different symmetries. We showed, without resorting to

  19. Complementary Constrains on Component based Multiphase Flow Problems, Should It Be Implemented Locally or Globally?

    NASA Astrophysics Data System (ADS)

    Shao, H.; Huang, Y.; Kolditz, O.

    2015-12-01

    Multiphase flow problems are numerically difficult to solve, as it often contains nonlinear Phase transition phenomena A conventional technique is to introduce the complementarity constraints where fluid properties such as liquid saturations are confined within a physically reasonable range. Based on such constraints, the mathematical model can be reformulated into a system of nonlinear partial differential equations coupled with variational inequalities. They can be then numerically handled by optimization algorithms. In this work, two different approaches utilizing the complementarity constraints based on persistent primary variables formulation[4] are implemented and investigated. The first approach proposed by Marchand et.al[1] is using "local complementary constraints", i.e. coupling the constraints with the local constitutive equations. The second approach[2],[3] , namely the "global complementary constrains", applies the constraints globally with the mass conservation equation. We will discuss how these two approaches are applied to solve non-isothermal componential multiphase flow problem with the phase change phenomenon. Several benchmarks will be presented for investigating the overall numerical performance of different approaches. The advantages and disadvantages of different models will also be concluded. References[1] E.Marchand, T.Mueller and P.Knabner. Fully coupled generalized hybrid-mixed finite element approximation of two-phase two-component flow in porous media. Part I: formulation and properties of the mathematical model, Computational Geosciences 17(2): 431-442, (2013). [2] A. Lauser, C. Hager, R. Helmig, B. Wohlmuth. A new approach for phase transitions in miscible multi-phase flow in porous media. Water Resour., 34,(2011), 957-966. [3] J. Jaffré, and A. Sboui. Henry's Law and Gas Phase Disappearance. Transp. Porous Media. 82, (2010), 521-526. [4] A. Bourgeat, M. Jurak and F. Smaï. Two-phase partially miscible flow and transport modeling in

  20. MAMAP - a new spectrometer system for column-averaged methane and carbon dioxide observations from aircraft: instrument description and performance analysis

    NASA Astrophysics Data System (ADS)

    Gerilowski, K.; Tretner, A.; Krings, T.; Buchwitz, M.; Bertagnolio, P. P.; Belemezov, F.; Erzinger, J.; Burrows, J. P.; Bovensmann, H.

    2011-02-01

    Carbon dioxide (CO2) and Methane (CH4) are the two most important anthropogenic greenhouse gases. CH4 is furthermore one of the most potent present and future contributors to global warming because of its large global warming potential (GWP). Our knowledge of CH4 and CO2 source strengths is based primarily on bottom-up scaling of sparse in-situ local point measurements of emissions and up-scaling of emission factor estimates or top-down modeling incorporating data from surface networks and more recently also by incorporating data from low spatial resolution satellite observations for CH4. There is a need to measure and retrieve the dry columns of CO2 and CH4 having high spatial resolution and spatial coverage. In order to fill this gap a new passive airborne 2-channel grating spectrometer instrument for remote sensing of small scale and mesoscale column-averaged CH4 and CO2 observations has been developed. This Methane Airborne MAPper (MAMAP) instrument measures reflected and scattered solar radiation in the short wave infrared (SWIR) and near-infrared (NIR) parts of the electro-magnetic spectrum at moderate spectral resolution. The SWIR channel yields measurements of atmospheric absorption bands of CH4 and CO2 in the spectral range between 1.59 and 1.69 μm at a spectral resolution of 0.82 nm. The NIR channel around 0.76 μm measures the atmospheric O2-A-band absorption with a resolution of 0.46 nm. MAMAP has been designed for flexible operation aboard a variety of airborne platforms. The instrument design and the performance of the SWIR channel, together with some results from on-ground and in-flight engineering tests are presented. The SWIR channel performance has been analyzed using a retrieval algorithm applied to the nadir measured spectra. Dry air column-averaged mole fractions are obtained from SWIR data only by dividing the retrieved CH4 columns by the simultaneously retrieved CO2 columns for dry air column CH4 (XCH4) and vice versa for dry air column CO2

  1. Shock Equation of State of Multi-Phase Epoxy-Based Composite (Al-MnO2-Epoxy)

    DTIC Science & Technology

    2010-10-01

    There are several studies in the literature regarding the equation of state of alumina-epoxy composites. Although these single component systems...paper presents the shock equation of state results on a multi-phase composite Al-MnO2-epoxy. Equation of state experiments were conducted using three...The experimental equation of state data is compared to volume averaged and mesoscale mixture models.

  2. Compact electron beam focusing column

    SciTech Connect

    Persaud, Arun; Leung, Ka-Ngo; Reijonen, Jani

    2001-07-13

    A novel design for an electron beam focusing column has been developed at LBNL. The design is based on a low-energy spread multicusp plasma source which is used as a cathode for electron beam production. The focusing column is 10 mm in length. The electron beam is focused by means of electrostatic fields. The column is designed for a maximum voltage of 50 kV. Simulations of the electron trajectories have been performed by using the 2-D simulation code IGUN and EGUN. The electron temperature has also been incorporated into the simulations. The electron beam simulations, column design and fabrication will be discussed in this presentation.

  3. Determination of propylthiouracil in pharmaceutical formulation by high-performance liquid-chromatography with a post-column iodine-azide reaction as a detection system.

    PubMed

    Zakrzewski, Robert

    2008-12-01

    A high-performance liquid chromatographic method with a post-column iodine-azide reaction has been chosen and tested for validity in quantitative determination of propylthiouracil in tablets. A mobile phase with a flow rate of 1.4 ml/min was conducted in the form of isocratic chromatography on a C18 column with acetonitrile-water-sodium azide solution (2.5%; pH 5.5) 24:26:50 (v/v/v). Unreacted iodine from post-column iodine-azide induced by reaction was monitored with visible detection at lambda=350 nm. The method proved both its linearity within the range of 8-100 nM (r2>0.9988) and satisfactory results of inter-day precision (RSD<4.2%) and accuracy (recovery>91%). The limits of detection (DDL) and quantification (DQL) reached the levels of 5 and 8 nM, respectively. The validation of the method comprised also its specificity. The results obtained proved the suitability and appropriateness of the suggested method for intended use.

  4. REVIEW OF EXPERIMENTAL CAPABILITIES AND HYDRODYNAMIC DATA FOR VALIDATION OF CFD-BASED PREDICTIONS FOR SLURRY BUBBLE COLUMN REACTORS

    SciTech Connect

    Donna Post Guillen; Daniel S. Wendt; Steven P. Antal; Michael Z. Podowski

    2007-11-01

    The purpose of this paper is to document the review of several open-literature sources of both experimental capabilities and published hydrodynamic data to aid in the validation of a Computational Fluid Dynamics (CFD) based model of a slurry bubble column (SBC). The review included searching the Web of Science, ISI Proceedings, and Inspec databases, internet searches as well as other open literature sources. The goal of this study was to identify available experimental facilities and relevant data. Integral (i.e., pertaining to the SBC system), as well as fundamental (i.e., separate effects are considered), data are included in the scope of this effort. The fundamental data is needed to validate the individual mechanistic models or closure laws used in a Computational Multiphase Fluid Dynamics (CMFD) simulation of a SBC. The fundamental data is generally focused on simple geometries (i.e., flow between parallel plates or cylindrical pipes) or custom-designed tests to focus on selected interfacial phenomena. Integral data covers the operation of a SBC as a system with coupled effects. This work highlights selected experimental capabilities and data for the purpose of SBC model validation, and is not meant to be an exhaustive summary.

  5. REVIEW OF EXPERIMENTAL CAPABILITIES AND HYDRODYNAMIC DATA FOR VALIDATION OF CFD BASED PREDICTIONS FOR SLURRY BUBBLE COLUMN REACTORS

    SciTech Connect

    Donna Post Guillen; Daniel S. Wendt

    2007-11-01

    The purpose of this paper is to document the review of several open-literature sources of both experimental capabilities and published hydrodynamic data to aid in the validation of a Computational Fluid Dynamics (CFD) based model of a slurry bubble column (SBC). The review included searching the Web of Science, ISI Proceedings, and Inspec databases, internet searches as well as other open literature sources. The goal of this study was to identify available experimental facilities and relevant data. Integral (i.e., pertaining to the SBC system), as well as fundamental (i.e., separate effects are considered), data are included in the scope of this effort. The fundamental data is needed to validate the individual mechanistic models or closure laws used in a Computational Multiphase Fluid Dynamics (CMFD) simulation of a SBC. The fundamental data is generally focused on simple geometries (i.e., flow between parallel plates or cylindrical pipes) or custom-designed tests to focus on selected interfacial phenomena. Integral data covers the operation of a SBC as a system with coupled effects. This work highlights selected experimental capabilities and data for the purpose of SBC model validation, and is not meant to be an exhaustive summary.

  6. In-plant testing of microbubble column flotation

    SciTech Connect

    Luttrell, G.H.; Mankosa, M.J.; Adel, G.T.; Yoon, R.H.

    1990-01-01

    This report describes progress in two areas: advanced instrumentation and column installation. The project is working with both 30-inch and 8-foot columns for coal flotation. The paper describes installation of the instrument package, the control loops, and the data acquisition system. Under the second area of study, a test plan was developed for a parametric study of the 8-foot column operating conditions (feed flow rate, gas flow rate, wash water flow rate, and froth addition) that were determined to influence separation efficiency on the 30-inch column. Results to date are discussed. 7 refs., 4 tabs. (CK)

  7. Dorsal column stimulator applications

    PubMed Central

    Yampolsky, Claudio; Hem, Santiago; Bendersky, Damián

    2012-01-01

    Background: Spinal cord stimulation (SCS) has been used to treat neuropathic pain since 1967. Following that, technological progress, among other advances, helped SCS become an effective tool to reduce pain. Methods: This article is a non-systematic review of the mechanism of action, indications, results, programming parameters, complications, and cost-effectiveness of SCS. Results: In spite of the existence of several studies that try to prove the mechanism of action of SCS, it still remains unknown. The mechanism of action of SCS would be based on the antidromic activation of the dorsal column fibers, which activate the inhibitory interneurons within the dorsal horn. At present, the indications of SCS are being revised constantly, while new applications are being proposed and researched worldwide. Failed back surgery syndrome (FBSS) is the most common indication for SCS, whereas, the complex regional pain syndrome (CRPS) is the second one. Also, this technique is useful in patients with refractory angina and critical limb ischemia, in whom surgical or endovascular treatment cannot be performed. Further indications may be phantom limb pain, chronic intractable pain located in the head, face, neck, or upper extremities, spinal lumbar stenosis in patients who are not surgical candidates, and others. Conclusion: Spinal cord stimulation is a useful tool for neuromodulation, if an accurate patient selection is carried out prior, which should include a trial period. Undoubtedly, this proper selection and a better knowledge of its underlying mechanisms of action, will allow this cutting edge technique to be more acceptable among pain physicians. PMID:23230533

  8. Joint numerical microscale simulations of multi-phase flow and NMR relaxation behaviour in porous media

    NASA Astrophysics Data System (ADS)

    Mohnke, O.; Ahrenholz, B.

    2011-12-01

    Nuclear Magnetic Resonance (NMR) is a useful tool for analyzing gas (methane) and fluids (water, oil) in rock formations in order to derive transport and storage properties such as pore-size distributions or relative permeability. Even though there is considerable NMR data available about hydraulic properties of rock formations, this information is only empirical. Thus, the aim of this paper is to present joint NMR and multi-phase flow simulations in micro-scale pore systems derived from micro-CT images to quantify relationships between NMR parameters and transport and storage properties of partially saturated rocks. Hereby, the NMR differential equations were implemented using an advection/diffusion lattice-Boltzmann method (LBM) where the flow field is computed by a coupled LBM CFD solver. The results of numerical imbibition and drainage experiments quantitatively agree with laboratory experiments with regard to frequently found peak shifts and bimodal NMR decay time distributions related to residual water in films and corners as well as to fluids/gases trapped in large pores. This numerical framework enables one to quantitatively describe NMR surface and bulk relaxation processes, diffusive coupling along with the multi-phase flow properties of partially saturated porous systems. Furthermore, it is a viable alternative to the more time-consuming and less controllable laboratory experiments. Such virtual experimental setups can considerably help to benchmark and validate statistical network models to better understand hydraulic properties of partially saturated rocks by using experimentally obtained NMR data.

  9. On the selection of primary variables in numerical formulation for modeling multiphase flow in porous media

    NASA Astrophysics Data System (ADS)

    Wu, Yu-Shu; Forsyth, Peter A.

    2001-04-01

    Selecting the proper primary variables is a critical step in efficiently modeling the highly nonlinear problem of multiphase subsurface flow in a heterogeneous porous-fractured media. Current simulation and ground modeling techniques consist of (1) spatial discretization of mass and/or heat conservation equations using finite difference or finite element methods; (2) fully implicit time discretization; (3) solving the nonlinear, discrete algebraic equations using a Newton iterative scheme. Previous modeling efforts indicate that the choice of primary variables for a Newton iteration not only impacts computational performance of a numerical code, but may also determine the feasibility of a numerical modeling study in many field applications. This paper presents an analysis and general recommendations for selecting primary variables in simulating multiphase, subsurface flow for one-active phase (Richards' equation), two-phase (gas and liquid) and three-phase (gas, water and nonaqueous phase liquid or NAPL) conditions. In many cases, a dynamic variable switching or variable substitution scheme may have to be used in order to achieve optimal numerical performance and robustness. The selection of primary variables depends in general on the sensitivity of the system of equations to the variables selected at given phase and flow conditions. We will present a series of numerical tests and large-scale field simulation examples, including modeling one (active)-phase, two-phase and three-phase flow problems in multi-dimensional, porous-fractured subsurface systems.

  10. On the selection of primary variables in numerical formulation for modeling multiphase flow in porous media.

    PubMed

    Wu, Y S; Forsyth, P A

    2001-04-01

    Selecting the proper primary variables is a critical step in efficiently modeling the highly nonlinear problem of multiphase subsurface flow in a heterogeneous porous-fractured media. Current simulation and ground modeling techniques consist of (1) spatial discretization of mass and/or heat conservation equations using finite difference or finite element methods; (2) fully implicit time discretization; (3) solving the nonlinear, discrete algebraic equations using a Newton iterative scheme. Previous modeling efforts indicate that the choice of primary variables for a Newton iteration not only impacts computational performance of a numerical code, but may also determine the feasibility of a numerical modeling study in many field applications. This paper presents an analysis and general recommendations for selecting primary variables in simulating multiphase, subsurface flow for one-active phase (Richards' equation), two-phase (gas and liquid) and three-phase (gas, water and nonaqueous phase liquid or NAPL) conditions. In many cases, a dynamic variable switching or variable substitution scheme may have to be used in order to achieve optimal numerical performance and robustness. The selection of primary variables depends in general on the sensitivity of the system of equations to the variables selected at given phase and flow conditions. We will present a series of numerical tests and large-scale field simulation examples, including modeling one (active)-phase, two-phase and three-phase flow problems in multi-dimensional, porous-fractured subsurface systems.

  11. Automatic connector joins structural columns

    NASA Technical Reports Server (NTRS)

    Jacquemin, G. G.

    1980-01-01

    Connector snap-locks over toothed bolthead mounted on column end, forming rigid joint that will not bend or twist. Connector is used in conventional construction to install temporary structures or as mechanical coupler. Up to nine receptacles can be clustered in one node to join up to nine converging columns.

  12. An Undergraduate Column Chromatography Experiment.

    ERIC Educational Resources Information Center

    Danot, M.; And Others

    1984-01-01

    Background information, list of materials needed, and procedures used are provided for an experiment designed to introduce undergraduate students to the theoretical and technical aspects of column chromatography. The experiment can also be shortened to serve as a demonstration of the column chromatography technique. (JN)

  13. The study of multiphase flow control during odor reproduction

    NASA Astrophysics Data System (ADS)

    Luo, Dehan; Yu, Hao; Fan, Danjun; He, Meiqiu

    2014-04-01

    Odor reproduction, is the use of the chemical composition of the basic components of odor recipe, according to a certain proportion, to control the flow of the various components, which make them sufficiently blended to achieve reproduction. In this paper, reproducing method is to find the corresponding liquid flavor, and then based on chemical flavor recipes, using flowmeters to control the chemical composition of the liquid flavor ratio. In the proportional control, the liquid chemical composition is very likely to be volatile, so that the proportional control is multiphase flow control. Measurement of the flow control will directly affect the odor reproducible results. Using electronic nose to obtain reproducible odor data, and then use pattern recognition algorithm to determine reproducible results. The experimental results can be achieved on the process of odor components multiphase flow proportional control parameter adjustment.

  14. Tabular Multiphase Equations of State for Metals and Their Applications

    NASA Astrophysics Data System (ADS)

    Levashov, Pavel R.; Khishchenko, Konstantin V.

    2007-12-01

    We present a method of interpolation of thermodynamic functions calculated by means of a multiphase equation of state for metals. The method takes into account melting, evaporation and sublimation phase transitions. It can be also applied in metastable regions of phase diagram including those under negative pressures. The method allows one to unambiguously determine the phase state of a given point of phase diagram. Several applications of the tabular multiphase equations of state are considered: simulation of the initial stage of electrical explosion of metal wires, formation of striations, interaction of intense laser pulses with matter etc. Information about phase state in every point of the flux allows us to study phase transition waves, apply different destruction criteria and analyze processes in metastable regions.

  15. Shock wave experiments to examine the multiphase properties of cerium

    SciTech Connect

    Jensen, Brian James

    2009-01-01

    There is a scientific need to obtain new data to constrain and refine next generation multi-phase equation-of-state (EOS) for metals. Experiments are needed to locate phase boundaries, determine transition kinetic times, and to obtain EOS and Hugoniot data for relevant phases. The objectives of the current work was to examine the multiphase properties for cerium including the dynamic melt boundary and the low-pressure solid-solid phase transition through the critical point. These objectives were addressed by performing plate impact experiment that used multiple experimental configuration including front-surface impact experiments to directly measure transition kinetics, multislug experiments that used the overtake method to measure sound speeds at pressure, and preheat experiments to map out phase boundaries. Preliminary data and analysis obtained for cerium will be presented.

  16. Measurement Of Multiphase Flow Water Fraction And Water-cut

    NASA Astrophysics Data System (ADS)

    Xie, Cheng-gang

    2007-06-01

    This paper describes a microwave transmission multiphase flow water-cut meter that measures the amplitude attenuation and phase shift across a pipe diameter at multiple frequencies using cavity-backed antennas. The multiphase flow mixture permittivity and conductivity are derived from a unified microwave transmission model for both water- and oil-continuous flows over a wide water-conductivity range; this is far beyond the capability of microwave-resonance-based sensors currently on the market. The water fraction and water cut are derived from a three-component gas-oil-water mixing model using the mixture permittivity or the mixture conductivity and an independently measured mixture density. Water salinity variations caused, for example, by changing formation water or formation/injection water breakthrough can be detected and corrected using an online water-conductivity tracking technique based on the interpretation of the mixture permittivity and conductivity, simultaneously measured by a single-modality microwave sensor.

  17. Fitting of a multiphase equation of state with swarm intelligence

    NASA Astrophysics Data System (ADS)

    Cox, G. A.; Christie, M. A.

    2015-10-01

    Hydrocode calculations require knowledge of the variation of pressure of a material with density and temperature, which is given by the equation of state. An accurate model needs to account for discontinuities in energy, density and properties of a material across a phase boundary. When generating a multiphase equation of state the modeller attempts to balance the agreement between the available data for compression, expansion and phase boundary location. However, this can prove difficult because minor adjustments in the equation of state for a single phase can have a large impact on the overall phase diagram. This paper describes how combining statistical-mechanics-based condensed matter physics models with a stochastic analysis technique called particle swarm optimisation, yields multiphase equations of state which give good agreement with experiment over a wide range of pressure-temperature space. Aluminium and tin are used as test cases in the proof of principle described in this paper.

  18. Fitting of a multiphase equation of state with swarm intelligence.

    PubMed

    Cox, G A; Christie, M A

    2015-10-14

    Hydrocode calculations require knowledge of the variation of pressure of a material with density and temperature, which is given by the equation of state. An accurate model needs to account for discontinuities in energy, density and properties of a material across a phase boundary. When generating a multiphase equation of state the modeller attempts to balance the agreement between the available data for compression, expansion and phase boundary location. However, this can prove difficult because minor adjustments in the equation of state for a single phase can have a large impact on the overall phase diagram. This paper describes how combining statistical-mechanics-based condensed matter physics models with a stochastic analysis technique called particle swarm optimisation, yields multiphase equations of state which give good agreement with experiment over a wide range of pressure-temperature space. Aluminium and tin are used as test cases in the proof of principle described in this paper.

  19. Method for producing nanocrystalline multicomponent and multiphase materials

    DOEpatents

    Eastman, J.A.; Rittner, M.N.; Youngdahl, C.J.; Weertman, J.R.

    1998-03-17

    A process for producing multi-component and multiphase nanophase materials is provided wherein a plurality of elements are vaporized in a controlled atmosphere, so as to facilitate thorough mixing, and then condensing and consolidating the elements. The invention also provides for a multicomponent and multiphase nanocrystalline material of specified elemental and phase composition having component grain sizes of between approximately 1 nm and 100 nm. This material is a single element in combination with a binary compound. In more specific embodiments, the single element in this material can be a transition metal element, a non-transition metal element, a semiconductor, or a semi-metal, and the binary compound in this material can be an intermetallic, an oxide, a nitride, a hydride, a chloride, or other compound. 6 figs.

  20. Method for producing nanocrystalline multicomponent and multiphase materials

    DOEpatents

    Eastman, Jeffrey A.; Rittner, Mindy N.; Youngdahl, Carl J.; Weertman, Julia R.

    1998-01-01

    A process for producing multi-component and multiphase nanophase materials is provided wherein a plurality of elements are vaporized in a controlled atmosphere, so as to facilitate thorough mixing, and then condensing and consolidating the elements. The invention also provides for a multicomponent and multiphase nanocrystalline material of specified elemental and phase composition having component grain sizes of between approximately 1 nm and 100 nm. This material is a single element in combination with a binary compound. In more specific embodiments, the single element in this material can be a transition metal element, a non-transition metal element, a semiconductor, or a semi-metal, and the binary compound in this material can be an intermetallic, an oxide, a nitride, a hydride, a chloride, or other compound.

  1. MULTI-PHASE FRACTURE-MATRIX INTERACTIONS UNDER STRESS CHANGES

    SciTech Connect

    A.S. Grader; D. Elsworth; P.M. Halleck; F. Alvarad; H. Yasuhara; A. Alajmi

    2002-04-20

    The main objectives of this project are to quantify the changes in fracture porosity and multi-phase transport properties as a function of confining stress. These changes will be integrated into conceptual and numerical models that will improve our ability to predict and optimize fluid transport in fractured system. This report details our progress on: (1) developing the direct experimental measurements of fracture aperture and topology using high-resolution x-ray micro-tomography, (2) modeling of fracture permeability in the presence of asperities and confining stress, and (3) simulation of two-phase fluid flow in a fracture and a layered matrix. The three-dimensional surface that describes the large-scale structure of the fracture in the porous medium can be determined using x-ray micro-tomography with significant accuracy. The distribution of fracture aperture is a difficult issue that we are studying and developing methods of quantification. The difficulties are both numerical and conceptual. Numerically, the three-dimensional data sets include millions, and sometimes, billions of points, and pose a computational challenge. The conceptual difficulties derive from the rough nature of the fracture surfaces, and the heterogeneous nature of the rock matrix. However, the high-resolution obtained by the imaging system provides us a much needed measuring environment on rock samples that are subjected to simultaneous fluid flow and confining stress. The absolute permeability of a fracture depends on the behavior of the asperities that keep it open. A model is being developed that predicts the permeability and average aperture of a fracture as a function of time under steady flow of water including the pressure solution at the asperity contact points. Several two-phase flow experiments in the presence of a fracture tip were performed in the past. At the present time, we are developing an inverse process using a simulation model to understand the fluid flow patterns in

  2. Comparison of column flotation cells

    SciTech Connect

    Honaker, R.Q.; Mohanty, M.K.; Ho, K.

    1995-08-01

    Six commercial column flotation technologies, i.e., Canadian, Flotaire, Jameson, Microcel, Packed-Column, and Turbo-air, were tested for the treatment of Illinois Basin fine coal and the results from each column compared based on separation performance and throughout capacity. The separation performance achieved by each cell approached and, in some cases, exceeded the ultimate performance predicted by release analysis. A comparison of the test results indicates differences in the selectivity obtained by each flotation column on the basis of both ash and sulfur rejection. This finding may be due to variations in cell hydrodynamics and the ability to support a deep froth phase among the different column cells. In addition, throughput capacity of each cell was found to differ, apparently due to the differences in the bubble-particle attachment environment, bubble size, and bubble population. Variations in the operating characteristics, such as reagent additions, aeration rate and wash water rate, were also noted and summarized in this publication.

  3. Ensemble phase averaging equations for multiphase flows in porous media, part I: the bundle-of-tubes model

    SciTech Connect

    Yang, Dali; Zhang, Duan; Currier, Robert

    2008-01-01

    A bundle-of-tubes construct is used as a model system to study ensemble averaged equations for multiphase flow in a porous material. Momentum equations for the fluid phases obtained from the method are similar to Darcy's law, but with additional terms. We study properties of the additional terms, and the conditions under which the averaged equations can be approximated by the diffusion model or the extended Darcy's law as often used in models for multiphase flows in porous media. Although the bundle-of-tubes model is perhaps the simplest model for a porous material, the ensemble averaged equation technique developed in this paper assumes the very same form in more general treatments described in Part 2 of the present work (Zhang 2009). Any model equation system intended for the more general cases must be understood and tested first using simple models. The concept of ensemble phase averaging is dissected here in physical terms, without involved mathematics through its application to the idealized bundle-of-tubes model for multiphase flow in porous media.

  4. Simulation of Compressible Multi-Phase Turbulent Reacting Flows

    DTIC Science & Technology

    2008-09-01

    Technology, 160:119– 150, 2000. [32] W.-W. Kim, S. Menon, and H. C. Mongia . Large eddy simulations of a gas turbine combustor flow. Combustion Science and...structures and shock induced heating can trigger ignition, combustion and turbulent flame propagation. In this research, a new and an efficient...Simulation of Compressible Multi-Phase Turbulent Reacting Flows Suresh Menon and Franklin Génin Computational Combustion Laboratory School of Aerospace

  5. Experimental and numerical investigation of multiphase flow in disordered media

    NASA Astrophysics Data System (ADS)

    Riaz, Amir; Tchelepi, Hamdi; Cinar, Yildiray

    2008-11-01

    We present laboratory scale experiments and network simulations to investigate the influence of capillary, gravitational and viscous forces on multiphase flow in disordered microscopic media. Two-dimensional experiments, which are performed in a vertical glass bead pack to understand microscopic behavior, demonstrate the existence of small scale instability that is analyzed with the theory of invasion percolation. Numerical simulations based on pore networks are carried out to help investigate the possibility of developing effective conservation laws at the macroscopic scale.

  6. In-situ formation of multiphase deposited thermal barrier coatings

    DOEpatents

    Subramanian, Ramesh

    2004-01-13

    A multiphase ceramic thermal barrier coating is provided. The coating is adapted for use in high temperature applications in excess of about 1200.degree. C., for coating superalloy components of a combustion turbine engine. The coating comprises a ceramic single or two oxide base layer disposed on the substrate surface; and a ceramic oxide reaction product material disposed on the base layer, the reaction product comprising the reaction product of the base layer with a ceramic single or two oxide overlay layer.

  7. Feasibility analysis of color removal from textile dyeing wastewater in a fixed-bed column system by surfactant-modified zeolite (SMZ).

    PubMed

    Ozdemir, Ozgur; Turan, Mustafa; Turan, Abdullah Zahid; Faki, Aysegul; Engin, Ahmet Baki

    2009-07-30

    In this study, the ability of surfactant-modified zeolite (SMZ) to remove color from real textile wastewater was investigated. Tests were performed in a fixed-bed column reactor and the surface of natural zeolite was modified with a quaternary amine surfactant hexadecyltrimethylammonium bromide (HTAB). The zeolite bed that was modified at 1 g L(-1) HTAB concentration and HTAB flow rate of 0.015 L min(-1) showed good performance in removing color. Effects of wastewater color intensity, flow rates and bed heights were also studied. Wastewater was diluted several times in the ratios of 25%, 50% and 75% in order to assess the influence of wastewater strength. The breakthrough curves of the original and diluted wastewaters are dispersed due to the fact that breakthrough came late at lower color intensities and saturation of the bed appeared faster at higher color intensities. The column had a 3-cm diameter and four different bed heights of 12.5, 25, 37.5 and 50 cm, which treated 5.25, 19.50, 35.25 and 51 L original textile wastewater, respectively, at the breakthrough time at a flow rate of 0.025 L min(-1). The theoretical service times evaluated from bed depth service time (BDST) approach for different column variables. The calculated and theoretical values of the exchange zone height were found with a difference of 27%. The various design parameters obtained from fixed-bed experimental studies showed good correlation with corresponding theoretical values, under different bed heights. The regeneration of the SMZ was also evaluated using a solution consisting of 30 g L(-1) NaCl and 1.5 g L(-1) NaOH at pH 12 and temperature 30 degrees C. Twice-regenerated SMZ showed the best performance compared with the others while first- and thrice-regenerated perform lower than the original SMZ.

  8. Effects of humic substances on the 241Am migration in a sandy aquifer: column experiments with Gorleben groundwater/sediment systems

    NASA Astrophysics Data System (ADS)

    Artinger, R.; Kienzler, B.; Schüßler, W.; Kim, J. I.

    1998-12-01

    Migration experiments were performed to study the influence of aquatic humic substances on the transport behavior of 241Am(III). Four groundwaters with different humic substance concentrations (DOC: 1 to 80 mg/l) were sampled together with Pleistocene aeolian quartz sand from the Gorleben site. Sand, groundwaters and humic substances were characterized by different analytical methods (e.g., ICP-MS, X-ray diffraction, X-ray fluorescence analysis, ultrafiltration). The sand was equilibrated with each groundwater under inert gas atmosphere with 1% CO 2 for a period of at least 3 months. As confirmed by ultrafiltration, the size distribution of humic colloids remained unchanged during equilibration. The hydraulic properties of sand columns were characterized with tritiated water as an inert tracer. Column and batch experiments were carried out with each groundwater as a function of the reaction period and flow velocity. In addition, the influence of the equilibration period of Am with groundwater was investigated prior to the injection into a column. The results revealed that increasing humic substance concentration reduced the Am sorption onto sand and enhanced the transport as colloid-borne Am species. The migration of colloid-borne Am was slightly faster than the groundwater flow velocity. Furthermore, the migration behavior of Am was found to depend on kinetically controlled interaction of humic colloid-bound Am with the sand surface. The application of the laboratory data to natural conditions was examined. The results were found applicable for the assessment of humic colloid facilitated radionuclide migration in natural aquifers.

  9. MAMAP - a new spectrometer system for column-averaged methane and carbon dioxide observations from aircraft: retrieval algorithm and first inversions for point source emission rates

    NASA Astrophysics Data System (ADS)

    Krings, T.; Gerilowski, K.; Buchwitz, M.; Reuter, M.; Tretner, A.; Erzinger, J.; Heinze, D.; Burrows, J. P.; Bovensmann, H.

    2011-04-01

    MAMAP is an airborne passive remote sensing instrument designed for measuring columns of methane (CH4) and carbon dioxide (CO2). The MAMAP instrument consists of two optical grating spectrometers: One in the short wave infrared band (SWIR) at 1590-1690 nm to measure CO2 and CH4 absorptions and another one in the near infrared (NIR) at 757-768 nm to measure O2 absorptions for reference purposes. MAMAP can be operated in both nadir and zenith geometry during the flight. Mounted on an airplane MAMAP can effectively survey areas on regional to local scales with a ground pixel resolution of about 29 m × 33 m for a typical aircraft altitude of 1250 m and a velocity of 200 km h-1. The retrieval precision of the measured column relative to background is typically ≲ 1% (1σ). MAMAP can be used to close the gap between satellite data exhibiting global coverage but with a rather coarse resolution on the one hand and highly accurate in situ measurements with sparse coverage on the other hand. In July 2007 test flights were performed over two coal-fired powerplants operated by Vattenfall Europe Generation AG: Jänschwalde (27.4 Mt CO2 yr-1) and Schwarze Pumpe (11.9 Mt CO2 yr-1), about 100 km southeast of Berlin, Germany. By using two different inversion approaches, one based on an optimal estimation scheme to fit Gaussian plume models from multiple sources to the data, and another using a simple Gaussian integral method, the emission rates can be determined and compared with emissions as stated by Vattenfall Europe. An extensive error analysis for the retrieval's dry column results (XCO2 and XCH4) and for the two inversion methods has been performed. Both methods - the Gaussian plume model fit and the Gaussian integral method - are capable of delivering reliable estimates for strong point source emission rates, given appropriate flight patterns and detailed knowledge of wind conditions.

  10. Enhanced Light Scattering of Secondary Organic Aerosols by Multiphase Reactions.

    PubMed

    Li, Kun; Li, Junling; Liggio, John; Wang, Weigang; Ge, Maofa; Liu, Qifan; Guo, Yucong; Tong, Shengrui; Li, Jiangjun; Peng, Chao; Jing, Bo; Wang, Dong; Fu, Pingqing

    2017-02-07

    Secondary organic aerosol (SOA) plays a pivotal role in visibility and radiative forcing, both of which are intrinsically linked to the refractive index (RI). While previous studies have focused on the RI of SOA from traditional formation processes, the effect of multiphase reactions on the RI has not been considered. Here, we investigate the effects of multiphase processes on the RI and light-extinction of m-xylene-derived SOA, a common type of anthropogenic SOA. We find that multiphase reactions in the presence of liquid water lead to the formation of oligomers from intermediate products such as glyoxal and methylglyoxal, resulting in a large enhancement in the RI and light-scattering of this SOA. These reactions will result in increases in light-scattering efficiency and direct radiative forcing of approximately 20%-90%. These findings improve our understanding of SOA optical properties and have significant implications for evaluating the impacts of SOA on the rapid formation of regional haze, global radiative balance, and climate change.

  11. Microstructure-based modelling of multiphase materials and complex structures

    NASA Astrophysics Data System (ADS)

    Werner, Ewald; Wesenjak, Robert; Fillafer, Alexander; Meier, Felix; Krempaszky, Christian

    2016-09-01

    Micromechanical approaches are frequently employed to monitor local and global field quantities and their evolution under varying mechanical and/or thermal loading scenarios. In this contribution, an overview on important methods is given that are currently used to gain insight into the deformational and failure behaviour of multiphase materials and complex structures. First, techniques to represent material microstructures are reviewed. It is common to either digitise images of real microstructures or generate virtual 2D or 3D microstructures using automated procedures (e.g. Voronoï tessellation) for grain generation and colouring algorithms for phase assignment. While the former method allows to capture exactly all features of the microstructure at hand with respect to its morphological and topological features, the latter method opens up the possibility for parametric studies with respect to the influence of individual microstructure features on the local and global stress and strain response. Several applications of these approaches are presented, comprising low and high strain behaviour of multiphase steels, failure and fracture behaviour of multiphase materials and the evolution of surface roughening of the aluminium top metallisation of semiconductor devices.

  12. Wettability control on multiphase flow in patterned microfluidics

    PubMed Central

    Zhao, Benzhong; Juanes, Ruben

    2016-01-01

    Multiphase flow in porous media is important in many natural and industrial processes, including geologic CO2 sequestration, enhanced oil recovery, and water infiltration into soil. Although it is well known that the wetting properties of porous media can vary drastically depending on the type of media and pore fluids, the effect of wettability on multiphase flow continues to challenge our microscopic and macroscopic descriptions. Here, we study the impact of wettability on viscously unfavorable fluid–fluid displacement in disordered media by means of high-resolution imaging in microfluidic flow cells patterned with vertical posts. By systematically varying the wettability of the flow cell over a wide range of contact angles, we find that increasing the substrate’s affinity to the invading fluid results in more efficient displacement of the defending fluid up to a critical wetting transition, beyond which the trend is reversed. We identify the pore-scale mechanisms—cooperative pore filling (increasing displacement efficiency) and corner flow (decreasing displacement efficiency)—responsible for this macroscale behavior, and show that they rely on the inherent 3D nature of interfacial flows, even in quasi-2D media. Our results demonstrate the powerful control of wettability on multiphase flow in porous media, and show that the markedly different invasion protocols that emerge—from pore filling to postbridging—are determined by physical mechanisms that are missing from current pore-scale and continuum-scale descriptions. PMID:27559089

  13. Backflow in twin-screw-type multiphase pump

    SciTech Connect

    Egashira, Kazuyuki; Shoda, Shinji; Tochikawa, Tetsuro; Furukawa, Akinori

    1998-02-01

    The performance of a twin-screw-type multiphase pump was investigated from the viewpoints of backflow in a gap along the twin-screw shafts and of scaleup parameters. Although both the backflow and the scaleup parameters have been recognized as important factors in developing multiphase pumps, they have not yet been clarified. The twin-screw pump was equipped with pressure sensors, set in the multiphase-test facility, and experimented with under various conditions to clarify the relationship between backflow rates and factors such as differential pressure, gas-void fractions (GVF`s), and the rotation speed of the shaft. A physical model was proposed with the empirical relationship of pressure distribution along the screw, and was successfully associated with scaleup parameters, such as the geometrical data of the twin-screw pump. Then it was used successfully to simulate the backflow in twin-screw pumps on relatively broad experimental conditions, judging from the comparison between the model and the experimental data.

  14. Success grows in pumping high-gas-fraction multiphase fluids

    SciTech Connect

    Butler, B.

    1999-07-01

    Judging from the reports from user companies and discussions at the pump symposium following the 1999 Offshore Technology Conference, three kinds of pumps have now progressed to the point where they might be considered commercial and have demonstrated their ability to handle a variety of multiphase flows. These are twin screw, progressive cavity, and helico-axial (H-A) pumps. The twin-screw and progressive cavity (PC) pumps are positive displacement. They develop pressure hydrostatically and are less sensitive to density changes. The H-A type is a centrifugal pump which develops pressure dynamically and is highly sensitive to variation in density which is a characteristic of a multiphase flow stream. Now that the technical hurdles are better understood, it is time to look at economic viability. The close links between inlet pressure, gas volumes, and cost can be demonstrated and general cost relationships can be suggested. This discussion focuses on surface applications using twin-screw pumps that have the most applications and data highlighting actual field experience of major oil and gas companies who benefit from this type of multiphase technology.

  15. Processing, Microstructure, and Properties of Multiphase Mo Silicide Alloys

    SciTech Connect

    Heatherly, L.; Liu, C.T.; Schneibel, J.H.

    1998-11-30

    Multiphase Mo silicide alloys containing T2 (Mo{sub 5}SiB{sub 2}), Mo{sub 3}Si and Mo phases where prepared by both melting and casting (M and C) and powder metallurgical (PM) processes. Glassy phases are observed in PM materials but not in M and C materials. Microstructural studies indicate that the primary phase is Mo-rich solid solution in alloys containing {le}(9.4Si+13.8B, at. %) and T2 in alloys with {ge}(9.8Si+14.6B). An eutectic composition is estimated to be close to Mo-9.6Si-14.2B. The mechanical properties of multiphase silicide alloys were determined by hardness, tensile and bending tests at room temperature. The multiphase alloy MSB-18 (Mo-9.4Si-13.8B) possesses a flexure strength distinctly higher than that of MoSi{sub 2} and other Mo{sub 5}Si{sub 3} silicide alloys containing no Mo particles. Also, MSB-18 is tougher than MoSi{sub 2} by a factor of 4.

  16. Fiber-Optical Sensors: Basics and Applications in Multiphase Reactors

    PubMed Central

    Li, Xiangyang; Yang, Chao; Yang, Shifang; Li, Guozheng

    2012-01-01

    This work presents a brief introduction on the basics of fiber-optical sensors and an overview focused on the applications to measurements in multiphase reactors. The most commonly principle utilized is laser back scattering, which is also the foundation for almost all current probes used in multiphase reactors. The fiber-optical probe techniques in two-phase reactors are more developed than those in three-phase reactors. There are many studies on the measurement of gas holdup using fiber-optical probes in three-phase fluidized beds, but negative interference of particles on probe function was less studied. The interactions between solids and probe tips were less studied because glass beads etc. were always used as the solid phase. The vision probes may be the most promising for simultaneous measurements of gas dispersion and solids suspension in three-phase reactors. Thus, the following techniques of the fiber-optical probes in multiphase reactors should be developed further: (1) online measuring techniques under nearly industrial operating conditions; (2) corresponding signal data processing techniques; (3) joint application with other measuring techniques.

  17. Multiphase pumping: indoor performance test and oilfield application

    NASA Astrophysics Data System (ADS)

    Kong, Xiangling; Zhu, Hongwu; Zhang, Shousen; Li, Jifeng

    2010-03-01

    Multiphase pumping is essentially a means of adding energy to the unprocessed effluent which enables the liquid and gas mixture to be transported over a long distances without prior separation. A reduction, consolidation, or elimination of the production infrastructure, such as separation equipments and offshore platforms can be developed more economically. Also it successfully lowed the backpressure of wells, revived dead wells and improved the production and efficiency of oilfield. This paper reviews the issues related to indoor performance test and an oilfield application of the helico-axial multiphase pump designed by China University of Petroleum (Beijing). Pump specification and its hydraulic design are given. Results of performance testing under different condition, such as operational speed and gas volume fraction (GVF) etc are presented. Experimental studies on combination of theoretical analysis showed the multiphase pump satisfies the similitude rule, which can be used in the development of new MPP design and performance prediction. Test results showed that rising the rotation speed and suction pressure could better its performance, pressure boost improved, high efficiency zone expanding and the flow rate related to the optimum working condition increased. The pump worked unstable as GVF increased to a certain extent and slip occurred between two phases in the pump, creating surging and gas lock at a high GVF. A case of application in Nanyang oilfield is also studied.

  18. Multiphase pumping: indoor performance test and oilfield application

    NASA Astrophysics Data System (ADS)

    Kong, Xiangling; Zhu, Hongwu; Zhang, Shousen; Li, Jifeng

    2009-12-01

    Multiphase pumping is essentially a means of adding energy to the unprocessed effluent which enables the liquid and gas mixture to be transported over a long distances without prior separation. A reduction, consolidation, or elimination of the production infrastructure, such as separation equipments and offshore platforms can be developed more economically. Also it successfully lowed the backpressure of wells, revived dead wells and improved the production and efficiency of oilfield. This paper reviews the issues related to indoor performance test and an oilfield application of the helico-axial multiphase pump designed by China University of Petroleum (Beijing). Pump specification and its hydraulic design are given. Results of performance testing under different condition, such as operational speed and gas volume fraction (GVF) etc are presented. Experimental studies on combination of theoretical analysis showed the multiphase pump satisfies the similitude rule, which can be used in the development of new MPP design and performance prediction. Test results showed that rising the rotation speed and suction pressure could better its performance, pressure boost improved, high efficiency zone expanding and the flow rate related to the optimum working condition increased. The pump worked unstable as GVF increased to a certain extent and slip occurred between two phases in the pump, creating surging and gas lock at a high GVF. A case of application in Nanyang oilfield is also studied.

  19. Wettability control on multiphase flow in patterned microfluidics

    NASA Astrophysics Data System (ADS)

    Juanes, Ruben; Zhao, Benzhong; MacMinn, Christopher

    2016-11-01

    Multiphase flow in porous media is important in many natural and industrial processes, including geologic CO2 sequestration, enhanced oil recovery, and water infiltration into soil. Although it is well known that the wetting properties of porous media can vary drastically depending on the type of media and pore fluids, the effect of wettability on multiphase flow continues to challenge our microscopic and macroscopic descriptions. Here, we study the impact of wettability on viscously unfavorable fluid-fluid displacement in disordered media by means of high-resolution imaging in microfluidic flow cells patterned with vertical posts. By systematically varying the wettability of the flow cell over a wide range of contact angles, we find that increasing the substrate's affinity to the injected fluid results in more efficient displacement of the defending fluid up to a critical wetting transition, beyond which the trend is reversed. We identify the pore-scale mechanisms-cooperative pore filling (increasing displacement efficiency) and corner flow (decreasing displacement efficiency)-responsible for this macroscale behavior, and show that they rely on the inherent 3D nature of interfacial flows, even in quasi-2D media. Our results demonstrate the powerful control of wettability on multiphase flow in porous media, and show that the markedly different invasion protocols that emerge-from pore-filling to post-bridging-are determined by physical mechanisms that are missing from current pore-scale and continuum-scale descriptions.

  20. Effect of extra-column volume on practical chromatographic parameters of sub-2-μm particle-packed columns in ultra-high pressure liquid chromatography.

    PubMed

    Wu, Naijun; Bradley, Ashley C; Welch, Christopher J; Zhang, Li

    2012-08-01

    Effects of extra-column volume on apparent separation parameters were studied in ultra-high pressure liquid chromatography with columns and inlet connection tubings of various internal diameters (id) using 50-mm long columns packed with 1.8-μm particles under isocratic conditions. The results showed that apparent retention factors were on average 5, 11, 18, and 41% lower than those corrected with extra-column volumes for 4.6-, 3.0-, 2.1-, and 1.0-mm id columns, respectively, when the extra-column volume (11.3 μL) was kept constant. Also, apparent pressures were 31, 16, 12, and 10% higher than those corrected with pressures from extra-column volumes for 4.6-, 3.0-, 2.1-, and 1.0-mm id columns at the respective optimum flow rate for a typical ultra-high pressure liquid chromatography system. The loss in apparent efficiency increased dramatically from 4.6- to 3.0- to 2.1- to 1.0-mm id columns, less significantly as retention factors increased. The column efficiency was significantly improved as the inlet tubing id was decreased for a given column. The results suggest that maximum ratio of extra-column volume to column void volume should be approximately 1:10 for column porosity more than 0.6 and a retention factor more than 5, where 80% or higher of theoretically predicted efficiency could be achieved.

  1. Entropic lattice Boltzmann method for multiphase flows: Fluid-solid interfaces

    NASA Astrophysics Data System (ADS)

    Mazloomi M., Ali; Chikatamarla, Shyam S.; Karlin, Iliya V.

    2015-08-01

    The recently introduced entropic lattice Boltzmann model (ELBM) for multiphase flows [A. Mazloomi M., S. S. Chikatamarla, and I. V. Karlin, Phys. Rev. Lett. 114, 174502 (2015), 10.1103/PhysRevLett.114.174502] is extended to the simulation of dynamic fluid-solid interface problems. The thermodynamically consistent, nonlinearly stable ELBM together with a polynomial representation of the equation of state enables us to investigate the dynamics of the contact line in a wide range of applications, from capillary filling to liquid drop impact onto a flat surfaces with different wettability. The static interface behavior is tested by means of the liquid column in a channel to verify the Young-Laplace law. The numerical results of a capillary filling problem in a channel with wettability gradient show an excellent match with the existing analytical solution. Simulations of drop impact onto both wettable and nonwettable surfaces show that the ELBM reproduces the experimentally observed drop behavior in a quantitative manner. Results reported herein demonstrate that the present model is a promising alternative for studying the vapor-liquid-solid interface dynamics.

  2. Electrical properties of multiphase composites based on carbon nanotubes and an optimized clay content

    NASA Astrophysics Data System (ADS)

    Egiziano, Luigi; Lamberti, Patrizia; Spinelli, Giovanni; Tucci, Vincenzo; Guadagno, Liberata; Vertuccio, Luigi

    2016-05-01

    The experimental results concerning the characterization of a multiphase nanocomposite systems based on epoxy matrix, loaded with different amount of multi-walled carbon nanotubes (MWCNTs) and an optimized Hydrotalcite (HT) clay content (i.e. 0.6 wt%), duly identified by an our previous theoretical study based on Design of Experiment (DoE), are presented. Dynamic-mechanical analysis (DMA) reveal that even the introduction of higher HT loading (up to 1%wt) don't affect significantly the mechanical properties of the nanocomposites while morphological investigations show an effective synergy between clay and carbon nanotubes that leads to peculiar micro/nanostructures that favor the creation of the electrical conductive network inside the insulating resin. An electrical characterization is carried out in terms of DC electrical conductivity, percolation threshold (EPT) and frequency response in the range 10Hz-1MHz. In particular, the measurements of the DC conductivity allow to obtain the typical "percolation" curve also found for classical CNT-polymer mixtures and a value of about 2 S/m for the electrical conductivity is achieved at the highest considered CNTs concentration (i.e. 1 wt%). The results suggest that multiphase nanocomposites obtained incorporating dispersive nanofillers, in addition to the conductive one, may be a valid alternative to the polymer blends, to improve the properties of the polymeric materials thus able to meet high demands, particularly concerning their mechanical and thermal stability and electrical features required in the aircraft engineering.

  3. Fluctuation-induced dynamics of multiphase liquid jets with ultra-low interfacial tension.

    PubMed

    Sauret, Alban; Spandagos, Constantinos; Shum, Ho Cheung

    2012-09-21

    Control of fluid dynamics at the micrometer scale is essential to emulsion science and materials design, which is ubiquitous in everyday life and is frequently encountered in industrial applications. Most studies on multiphase flow focus on oil-water systems with substantial interfacial tension. Advances in microfluidics have enabled the study of multiphase flow with more complex dynamics. Here, we show that the evolution of the interface in a jet surrounded by a co-flowing continuous phase with an ultra-low interfacial tension presents new opportunities to the control of flow morphologies. The introduction of a harmonic perturbation to the dispersed phase leads to the formation of interfaces with unique shapes. The periodic structures can be tuned by controlling the fluid flow rates and the input perturbation; this demonstrates the importance of the inertial effects in flow control at ultra-low interfacial tension. Our work provides new insights into microfluidic flows at ultra-low interfacial tension and their potential applications.

  4. Synchrotron radiation measurement of multiphase fluid saturations in porous media: Experimental technique and error analysis

    NASA Astrophysics Data System (ADS)

    Tuck, David M.; Bierck, Barnes R.; Jaffé, Peter R.

    1998-06-01

    Multiphase flow in porous media is an important research topic. In situ, nondestructive experimental methods for studying multiphase flow are important for improving our understanding and the theory. Rapid changes in fluid saturation, characteristic of immiscible displacement, are difficult to measure accurately using gamma rays due to practical restrictions on source strength. Our objective is to describe a synchrotron radiation technique for rapid, nondestructive saturation measurements of multiple fluids in porous media, and to present a precision and accuracy analysis of the technique. Synchrotron radiation provides a high intensity, inherently collimated photon beam of tunable energy which can yield accurate measurements of fluid saturation in just one second. Measurements were obtained with precision of ±0.01 or better for tetrachloroethylene (PCE) in a 2.5 cm thick glass-bead porous medium using a counting time of 1 s. The normal distribution was shown to provide acceptable confidence limits for PCE saturation changes. Sources of error include heat load on the monochromator, periodic movement of the source beam, and errors in stepping-motor positioning system. Hypodermic needles pushed into the medium to inject PCE changed porosity in a region approximately ±1 mm of the injection point. Improved mass balance between the known and measured PCE injection volumes was obtained when appropriate corrections were applied to calibration values near the injection point.

  5. A lattice Boltzmann model for multiphase flows with large density ratio

    NASA Astrophysics Data System (ADS)

    Zheng, H. W.; Shu, C.; Chew, Y. T.

    2006-10-01

    A lattice Boltzmann model for simulating multiphase flows with large density ratios is described in this paper. The method is easily implemented. It does not require solving the Poisson equation and does not involve the complex treatments of derivative terms. The interface capturing equation is recovered without any additional terms as compared to other methods [M.R. Swift, W.R. Osborn, J.M. Yeomans, Lattice Boltzmann simulation of liquid-gas and binary fluid systems, Phys. Rev. E 54 (1996) 5041-5052; T. Inamuro, T. Ogata, S. Tajima, N. Konishi, A lattice Boltzmann method for incompressible two-phase flows with large density differences, J. Comput. Phys. 198 (2004) 628-644; T. Lee, C.-L. Lin, A stable discretization of the lattice Boltzmann equation for simulation of incompressible two-phase flows at high density ratio, J. Comput. Phys. 206 (2005) 16-47]. Besides, it requires less discrete velocities. As a result, its efficiency could be greatly improved, especially in 3D applications. It is validated by several cases: a bubble in a stationary flow and the capillary wave. The numerical surface tension obtained from the Laplace law and the interface profile agrees very well with the respective analytical solution. The method is further verified by its application to capillary wave and the bubble rising under buoyancy with comparison to other methods. All the numerical experiments show that the present approach can be used to model multiphase flows with large density ratios.

  6. Modeling non-isothermal multiphase multi-species reactive chemical transport in geologic media

    SciTech Connect

    Tianfu Xu; Gerard, F.; Pruess, K.; Brimhall, G.

    1997-07-01

    The assessment of mineral deposits, the analysis of hydrothermal convection systems, the performance of radioactive, urban and industrial waste disposal, the study of groundwater pollution, and the understanding of natural groundwater quality patterns all require modeling tools that can consider both the transport of dissolved species as well as their interactions with solid (or other) phases in geologic media and engineered barriers. Here, a general multi-species reactive transport formulation has been developed, which is applicable to homogeneous and/or heterogeneous reactions that can proceed either subject to local equilibrium conditions or kinetic rates under non-isothermal multiphase flow conditions. Two numerical solution methods, the direct substitution approach (DSA) and sequential iteration approach (SIA) for solving the coupled complex subsurface thermo-physical-chemical processes, are described. An efficient sequential iteration approach, which solves transport of solutes and chemical reactions sequentially and iteratively, is proposed for the current reactive chemical transport computer code development. The coupled flow (water, vapor, air and heat) and solute transport equations are also solved sequentially. The existing multiphase flow code TOUGH2 and geochemical code EQ3/6 are used to implement this SIA. The flow chart of the coupled code TOUGH2-EQ3/6, required modifications of the existing codes and additional subroutines needed are presented.

  7. A Physically Based Approach for Modeling Multiphase Fracture-Matrix Interaction in Fractured Porous Media

    SciTech Connect

    Wu, Yu-Shu; Pan, Lehua; Pruess, Karsten

    2004-03-15

    Modeling fracture-matrix interaction within a complex multiple phase flow system is a key issue for fractured reservoir simulation. Commonly used mathematical models for dealing with such interactions employ a dual- or multiple-continuum concept, in which fractures and matrix are represented as overlapping, different, but interconnected continua, described by parallel sets of conservation equations. The conventional single-point upstream weighting scheme, in which the fracture relative permeability is used to represent the counterpart at the fracture-matrix interface, is the most common scheme by which to estimate flow mobility for fracture-matrix flow terms. However, such a scheme has a serious flaw, which may lead to unphysical solutions or significant numerical errors. To overcome the limitation of the conventional upstream weighting scheme, this paper presents a physically based modeling approach for estimating physically correct relative permeability in calculating multiphase flow between fractures and the matrix, using continuity of capillary pressure at the fracture-matrix interface. The proposed approach has been implemented into two multiphase reservoir simulators and verified using analytical solutions and laboratory experimental data. The new method is demonstrated to be accurate, numerically efficient, and easy to implement in dual- or multiple-continuum models.

  8. Tropospheric NO2 and HCHO columns derived from ground-based MAX-DOAS system in Guangzhou, China and comparison with satellite observations: First results within the EU FP7 project MarcoPolo

    NASA Astrophysics Data System (ADS)

    Drosoglou, Theano; Kouremeti, Natalia; Bais, Alkis; Zyrichidou, Irene; Li, Shu; Balis, Dimitris; Huang, Zhonghui

    2016-04-01

    A miniature MAX-DOAS system, Phaethon, has been developed at the Laboratory of Atmospheric Physics of the Aristotle University of Thessaloniki, Greece, for ground-based monitoring of column densities of atmospheric gases. Simultaneous measurements with two Phaethon systems at the city centre of Thessaloniki and at a rural location about 30 km away have shown that Phaethon provides NO2 and HCHO tropospheric column measurements of acceptable accuracy under both low and high air-pollution levels. Currently three systems have been deployed in areas with different pollution patterns to support air quality and satellite validation studies. In the framework of the EU FP7 Monitoring and Assessment of Regional air quality in China using space Observations, Project Of Long-term sino-european co-Operation, MarcoPolo project, one of the Phaethon systems has been installed since April 2015 in the Guangzhou region in China. Tropospheric NO2 and HCHO columns derived at Guangzhou during the first 10 months of operation are compared with corresponding retrievals from OMI/Aura and GOME-2/Metop-A and /Metop-B satellite sensors. The area is characterized by humid subtropical monsoon climate and cloud-free conditions are rather rare from early March to mid-October. Despite this limitation and the short period of operation of Phaethon in Guangzhou, the agreement between ground-based and satellite observations is generally good for both NO2 and HCHO. It appears that GOME-2 sensors seem to underestimate the tropospheric NO2, possibly due to their large pixel size, whereas the comparison with OMI data is better, especially when a small cloud fraction (< 0.2) is used for cloud screening.

  9. Seismic behavior of lightweight concrete columns

    NASA Astrophysics Data System (ADS)

    Rabbat, B. G.; Daniel, J. I.; Weinmann, T. L.; Hanson, N. W.

    1982-09-01

    Sixteen full-scale, column-beam assemblies, which represented a portion of a frame subjected to simulated seismic loading, were tested. Controlled test parameters included concrete type, column size, amount of main column steel, size and spacing of column confining hoops, and magnitude of column axial load. The columns were subjected to constant axial load and slow moment reversals at increasing inelastic deformations. Test data showed that properly designed lightweight concrete columns maintained ductility and strength when subjected to large inelastic deformations from load reversals. Confinement requirements for normal weight concrete columns were shown to be applicable to lightweight concrete columns up to thirty percent of the design strength.

  10. Pore-Scale Investigation on Stress-Dependent Characteristics of Granular Packs and Their Impact on Multiphase Fluid Distribution

    NASA Astrophysics Data System (ADS)

    Torrealba, V.; Karpyn, Z.; Yoon, H.; Hart, D. B.; Klise, K. A.

    2013-12-01

    The pore-scale dynamics that govern multiphase flow under variable stress conditions are not well understood. This lack of fundamental understanding limits our ability to quantitatively predict multiphase flow and fluid distributions in natural geologic systems. In this research, we focus on pore-scale, single and multiphase flow properties that impact displacement mechanisms and residual trapping of non-wetting phase under varying stress conditions. X-ray micro-tomography is used to image pore structures and distribution of wetting and non-wetting fluids in water-wet synthetic granular packs, under dynamic load. Micro-tomography images are also used to determine structural features such as medial axis, surface area, and pore body and throat distribution; while the corresponding transport properties are determined from Lattice-Boltzmann simulations performed on lattice replicas of the imaged specimens. Results are used to investigate how inter-granular deformation mechanisms affect fluid displacement and residual trapping at the pore-scale. This will improve our understanding of the dynamic interaction of mechanical deformation and fluid flow during enhanced oil recovery and geologic CO2 sequestration. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

  11. Common catabolic enzyme patterns in a microplankton community of the Humboldt Current System off northern and central-south Chile: Malate dehydrogenase activity as an index of water-column metabolism in an oxygen minimum zone

    NASA Astrophysics Data System (ADS)

    González, R. R.; Quiñones, R. A.

    2009-07-01

    An extensive subsurface oxygen minimum zone off northern and central-south Chile, associated with the Peru-Chile undercurrent, has important effects on the metabolism of the organisms inhabiting therein. Planktonic species deal with the hypoxic and anoxic environments by relying on biochemical as well as physiological processes related to their anaerobic metabolisms. Here we characterize, for the first time, the potential enzymatic activities involved in the aerobic and anaerobic energy production pathways of microplanktonic organisms (<100 μm), their relationship, and this relationship's association with the oxygen concentration and microplanktonic biomass in the oxygen minimum zone and adjacent areas of the Humboldt Current System water column. Our results demonstrate significant potential enzymatic activity of catabolic pathways in the oxygen minimum zone. Malate dehydrogenase had the highest oxidizing activity of nicotinamide adenine dinucleotide (reduced form) in the batch of catabolic enzymatic activities assayed, including potential pyruvate oxidoreductases activity, the electron transport system, and dissimilatory nitrate reductase. Malate dehydrogenase correlated significantly with almost all the enzymes analyzed within and above the oxygen minimum zone, and also with the oxygen concentration and microplankton biomass in the water column of the Humboldt Current System, especially in the oxygen minimum zone off Iquique. These results suggest a possible specific pattern for the catabolic activity of the microplanktonic realm associated with the oxygen minimum zone spread along the Humboldt Current System off Chile. We hypothesize that malate dehydrogenase activity could be an appropriate indicator of microplankton catabolism in the oxygen minimum zone and adjacent areas.

  12. MAMAP - a new spectrometer system for column-averaged methane and carbon dioxide observations from aircraft: retrieval algorithm and first inversions for point source emission rates

    NASA Astrophysics Data System (ADS)

    Krings, T.; Gerilowski, K.; Buchwitz, M.; Reuter, M.; Tretner, A.; Erzinger, J.; Heinze, D.; Pflüger, U.; Burrows, J. P.; Bovensmann, H.

    2011-09-01

    MAMAP is an airborne passive remote sensing instrument designed to measure the dry columns of methane (CH4) and carbon dioxide (CO2). The MAMAP instrument comprises two optical grating spectrometers: the first observing in the short wave infrared band (SWIR) at 1590-1690 nm to measure CO2 and CH4 absorptions, and the second in the near infrared (NIR) at 757-768 nm to measure O2 absorptions for reference/normalisation purposes. MAMAP can be operated in both nadir and zenith geometry during the flight. Mounted on an aeroplane, MAMAP surveys areas on regional to local scales with a ground pixel resolution of approximately 29 m × 33 m for a typical aircraft altitude of 1250 m and a velocity of 200 km h-1. The retrieval precision of the measured column relative to background is typically ≲ 1% (1σ). MAMAP measurements are valuable to close the gap between satellite data, having global coverage but with a rather coarse resolution, on the one hand, and highly accurate in situ measurements with sparse coverage on the other hand. In July 2007, test flights were performed over two coal-fired power plants operated by Vattenfall Europe Generation AG: Jänschwalde (27.4 Mt CO2 yr-1) and Schwarze Pumpe (11.9 Mt CO2 yr-1), about 100 km southeast of Berlin, Germany. By using two different inversion approaches, one based on an optimal estimation scheme to fit Gaussian plume models from multiple sources to the data, and another using a simple Gaussian integral method, the emission rates can be determined and compared with emissions reported by Vattenfall Europe. An extensive error analysis for the retrieval's dry column results (XCO2 and XCH4) and for the two inversion methods has been performed. Both methods - the Gaussian plume model fit and the Gaussian integral method - are capable of deriving estimates for strong point source emission rates that are within ±10% of the reported values, given appropriate flight patterns and detailed knowledge of wind conditions.

  13. Capital City Column.

    ERIC Educational Resources Information Center

    Carter, Carl

    1994-01-01

    Provides a suggested model for SCHOOLNET, a voice, video, and data network. Proposes that library media centers should be the site of the SCHOOLNET hub; students and teachers should be able to access the INFOhio library automation system and other information systems; and digital fiber optic hubs and trunk lines should connect school buildings…

  14. High Precision, Absolute Total Column Ozone Measurements from the Pandora Spectrometer System: Comparisons with Data from a Brewer Double Monochromator and Aura OMI

    NASA Technical Reports Server (NTRS)

    Tzortziou, Maria A.; Herman, Jay R.; Cede, Alexander; Abuhassan, Nader

    2012-01-01

    We present new, high precision, high temporal resolution measurements of total column ozone (TCO) amounts derived from ground-based direct-sun irradiance measurements using our recently deployed Pandora single-grating spectrometers. Pandora's small size and portability allow deployment at multiple sites within an urban air-shed and development of a ground-based monitoring network for studying small-scale atmospheric dynamics, spatial heterogeneities in trace gas distribution, local pollution conditions, photochemical processes and interdependencies of ozone and its major precursors. Results are shown for four mid- to high-latitude sites where different Pandora instruments were used. Comparisons with a well calibrated double-grating Brewer spectrometer over a period of more than a year in Greenbelt MD showed excellent agreement and a small bias of approximately 2 DU (or, 0.6%). This was constant with slant column ozone amount over the full range of observed solar zenith angles (15-80), indicating adequate Pandora stray light correction. A small (1-2%) seasonal difference was found, consistent with sensitivity studies showing that the Pandora spectral fitting TCO retrieval has a temperature dependence of 1% per 3K, with an underestimation in temperature (e.g., during summer) resulting in an underestimation of TCO. Pandora agreed well with Aura-OMI (Ozone Measuring Instrument) satellite data, with average residuals of <1% at the different sites when the OMI view was within 50 km from the Pandora location and OMI-measured cloud fraction was <0.2. The frequent and continuous measurements by Pandora revealed significant short-term (hourly) temporal changes in TCO, not possible to capture by sun-synchronous satellites, such as OMI, alone.

  15. A review of oscillating water columns.

    PubMed

    Heath, T V

    2012-01-28

    This paper considers the history of oscillating water column (OWC) systems from whistling buoys to grid-connected power generation systems. The power conversion from the wave resource through to electricity via pneumatic and shaft power is discussed in general terms and with specific reference to Voith Hydro Wavegen's land installed marine energy transformer (LIMPET) plant on the Scottish island of Islay and OWC breakwater systems. A report on the progress of other OWC systems and power take-off units under commercial development is given, and the particular challenges faced by OWC developers reviewed.

  16. Telescoping columns. [parabolic antenna support

    NASA Technical Reports Server (NTRS)

    Mazur, J. T. (Inventor)

    1980-01-01

    An extendable column is described which consists of several axially elongated rigid structural sections nested within one another. Each section includes a number of rotatably attached screws running along its length. The next inner section includes threaded lugs oriented to threadingly engage the screws. The column is extended or retracted upon rotation of the screws. The screws of each section are selectively rotated by a motor and an engagement mechanism.

  17. Treatment of non-ideality in the multiphase model SPACCIM - Part 1: Model development

    NASA Astrophysics Data System (ADS)

    Rusumdar, A. J.; Wolke, R.; Tilgner, A.; Herrmann, H.

    2015-06-01

    Ambient tropospheric deliquesced particles generally comprise a complex mixture of electrolytes, organic compounds, and water. Dynamic modeling of physical and chemical processes in this complex matrix is challenging. Thus, up-to-date multiphase chemistry models do generally not consider non-ideal solution effects. Therefore, the present study was aimed at the further development of the SPACCIM model to treat both complex multiphase chemistry and phase transfer processes considering newly non-ideality properties of concentrated aerosol solutions. The present paper describes firstly, the performed model development including (i) the kinetic implementation of the non-ideality in the SPACCIM framework, (ii) the advancements in the coupling scheme of microphysics and multiphase chemistry and (iii) the required adjustments of the numerical schemes, especially in the sparse linear solver and the calculation of the Jacobian. Secondly, results of performed sensitivity investigations are outlined aiming at the evaluation of different activity coefficient modules and the examination of the contributions of different intermolecular forces to the overall activity coefficients. Finally, first results obtained with the new model framework are presented. The main product of the performed model development is the new kinetic model approach SPACCIM-SpactMod, which utilizes activities in reaction terms instead of aqueous concentrations. Based on an intercomparison of different activity coefficient models and the comparison with experimental data, AIOMFAC was selected as base model and extended by additional interaction parameters from literature for mixed organic-inorganic systems. Moreover, the performance and the capability of the applied activity coefficient module were evaluated by means of water activity measurements, literature data and results of other thermodynamic equilibrium models. Comprehensive comparison studies showed that the SpactMod (SPACCIM activity coefficient

  18. LIQUID-LIQUID EXTRACTION COLUMNS

    DOEpatents

    Thornton, J.D.

    1957-12-31

    This patent relates to liquid-liquid extraction columns having a means for pulsing the liquid in the column to give it an oscillatory up and down movement, and consists of a packed column, an inlet pipe for the dispersed liquid phase and an outlet pipe for the continuous liquid phase located in the direct communication with the liquid in the lower part of said column, an inlet pipe for the continuous liquid phase and an outlet pipe for the dispersed liquid phase located in direct communication with the liquid in the upper part of said column, a tube having one end communicating with liquid in the lower part of said column and having its upper end located above the level of said outlet pipe for the dispersed phase, and a piston and cylinder connected to the upper end of said tube for applying a pulsating pneumatic pressure to the surface of the liquid in said tube so that said surface rises and falls in said tube.

  19. Measurement of Surface Tension of Solid Cu by Improved Multiphase Equilibrium

    NASA Astrophysics Data System (ADS)

    Nakamoto, Masashi; Liukkonen, Matti; Friman, Michael; Heikinheimo, Erkki; Hämäläinen, Marko; Holappa, Lauri

    2008-08-01

    The surface tension of solid Cu was measured with the multiphase equilibrium (MPE) method in a Pb-Cu system at 700 °C, 800 °C, and 900 °C. A special focus was on the measurement of angles involved in MPE. First, the effect of reading error in each angle measurement on the final result of surface tension of solid was simulated. It was found that the two groove measurements under atmosphere conditions are the primary sources of error in the surface tension of solid in the present system. Atomic force microscopy (AFM) was applied to these angle measurements as a new method with high accuracy. The obtained surface-tension values of solid Cu in the present work were 1587, 1610, and 1521 mN/m at 700 °C, 800 °C, and 900 °C, respectively, representing reasonable temperature dependence.

  20. Weir plate stripping column for alcohol production. Final report

    SciTech Connect

    Ross, J.D.; Sharpe, S.

    1984-01-01

    This project consisted of the design, construction and test of a new concept for an alcohol stripping column. The concept involved the use of a series of dams and weirs in an inclined tube to produce the effects of plates in a conventional column. A secondary objective was to test the use of plastic as a construction material. It was felt that the concept would lead to a low cost system that would have application in small farm systems for the production of alcohol fuel. It was also felt that the stability of the system would be ideal for systems that would use solar power for a heat source. A plastic stripping tower containing 25 plates was tested on a beer from fermented corn meal. The column produced 140 proof alcohol, and in general, worked as expected. The relative low proof of the output and the lack of a steep gradient along the tube, indicated that the column is not as efficient as conventional columns. The test indicated that CPVC plastic could be used in the construction of a column; however, sealing problems and its cost make it questionable that the use of this type material would lead to a lower cost column. 7 figures.

  1. Quantitative analytical electron microscopy of multiphase alloys.

    PubMed

    Prybylowski, J; Ballinger, R; Elliott, C

    1989-02-01

    In this paper, we present a technique for analysis of composition gradients, using an analytical electron microscope, within the primary phase of a two-phase alloy for the case where the second-phase particle size is similar to the size of the irradiated volume. If the composition difference between the two phases is large, the detected compositional fluctuations associated with varying phase fractions may mask any underlying composition gradient of the primary phase. The analysis technique was used to determine grain boundary chromium concentration gradients in a nickel-base superalloy, alloy X-750. The technique may also be of use in other alloy systems.

  2. In-plant testing of microbubble column flotation

    SciTech Connect

    Luttrell, G.H.; Mankosa, M.J.; Adel, G.T.; Yoon, R.H.

    1991-01-01

    Testing of micro-bubble column flotation continued. Work during this time frame was concentrated on completion of the automated control and data acquisition system and the factorial test plan for evaluating the performance of the 8-foot column (Tasks 2.5 and 3.3). Preliminary results obtained from the factorial test program indicate that higher frother addition and aeration rates result in a higher separation efficiency. Furthermore, an increase in collector dosage results in higher column yields under most conditions. The Allen-Bradley PLC has been installed and program development completed for control of the 8-foot column. A completely automated start-up and shut-down sequence has been developed. This sequence can be initiated by the operator from a plant floor industrial interface. Instrumentation of the 30-inch column has also been completed. Testing of this instrumentation is currently underway. 11 figs., 5 tabs.

  3. Structural, microstructural and surface properties of a specific CeO{sub 2}-Bi{sub 2}O{sub 3} multiphase system obtained at 600 {sup o}C

    SciTech Connect

    Bourja, Lamia; Bakiz, Bahcine; Benlhachemi, Abdeljalil; Ezahri, Mohamed; Villain, Sylvie; Crosnier, Olivier; Favotto, Claude; Gavarri, Jean-Raymond

    2011-03-15

    Polycrystalline samples of (1-x) CeO{sub 2}-x/2 Bi{sub 2}O{sub 3} phases, where x is the atom fraction of bismuth have been synthesized by the precipitation process and after the thermal treatment at 600 {sup o}C, under air. Samples are first characterized by the X-ray diffraction and scanning electron microscopy. To determine the samples specific surface areas, Brunauer-Emmett-Teller (BET) analyses have been performed. In the composition range 0{<=}x{<=}0.20, a cubic solid solution with fluorite structure is obtained. For compositions x comprised between 0.30 and 0.90, two types of T' (or {beta}') and T (or {beta}) tetragonal phases, similar to the well-known {beta}' or {beta} Bi{sub 2}O{sub 3} metastable structural varieties, are observed. However, the crystal cell volumes of these {beta}' or {beta} Bi{sub 2}O{sub 3} phases increase with the composition x in bismuth: this might be due to the presence of defects or substitution by cerium atoms, in the tetragonal lattices. Using X-ray diffraction profile analyses, correlations between bismuth composition x and crystal sizes or lattice distortions have been established. The solid-gas interactions between these polycrystalline materials and air-CH{sub 4} and air-CO flows have been studied as a function of temperature and composition x, using Fourier transform infrared (FTIR) analyses of the conversions of CH{sub 4} and CO gases into the CO{sub 2} gas. The transformations of CH{sub 4} and CO molecules as a function of time and temperature are determined through the intensities of FTIR CO{sub 2} absorption bands. Using the specific surface areas determined from BET analyses, these FTIR intensities have been normalized and compared. For all bismuth compositions, a low catalytic reactivity is observed with air-CH{sub 4} gas flows, while, for the highest bismuth compositions, a high catalytic reactivity is observed with air-CO gas flows. -- Graphical abstract: Catalytic efficiencies of CeO{sub 2}-Bi{sub 2}O{sub 3}system

  4. Liquid-based gating mechanism with tunable multiphase selectivity and antifouling behaviour

    SciTech Connect

    Hou, Xu; Hu, Yuhang; Grinthal, Alison; Khan, Mughees; Aizenberg, Joanna

    2015-03-04

    Living organisms make extensive use of micro- and nanometre-sized pores as gatekeepers for controlling the movement of fluids, vapours and solids between complex environments. In addition, the ability of such pores to coordinate multiphase transport, in a highly selective and subtly triggered fashion and without clogging, has inspired interest in synthetic gated pores for applications ranging from fluid processing to 3D printing and lab-on-chip systems1-10.But although specific gating and transport behaviours have been realized by precisely tailoring pore surface chemistries and pore geometries6,11–17, a single system capable of controlling complex, selective multiphase transport has remained a distant prospect, and fouling is nearly inevitable.Here we introduce a gating mechanism that uses a capillary-stabilized liquid as a reversible, reconfigurable gate that fills and seals pores in the closed state, and creates a non-fouling, liquid-lined pore in the open state.Theoretical modelling and experiments demonstrate that for each transport substance, the gating threshold—the pressure needed to open the pores—can be rationally tuned over a wide pressure range. This enables us to realize in one system differential response profiles for a variety of liquids and gases, even letting liquids flow through the pore while preventing gas from escaping.These capabilities allow us to dynamically modulate gas–liquid sorting in a microfluidic flow and to separate a three-phase air water–oil mixture, with the liquid lining ensuring sustained antifouling behaviour. Because the liquid gating strategy enables efficient long-term operation and can be applied to a variety of pore structures and membrane materials, and to micro- as well as macroscale fluid systems, we expect it to prove useful in a wide range of applications.

  5. Liquid-based gating mechanism with tunable multiphase selectivity and antifouling behaviour

    DOE PAGES

    Hou, Xu; Hu, Yuhang; Grinthal, Alison; ...

    2015-03-04

    Living organisms make extensive use of micro- and nanometre-sized pores as gatekeepers for controlling the movement of fluids, vapours and solids between complex environments. In addition, the ability of such pores to coordinate multiphase transport, in a highly selective and subtly triggered fashion and without clogging, has inspired interest in synthetic gated pores for applications ranging from fluid processing to 3D printing and lab-on-chip systems1-10.But although specific gating and transport behaviours have been realized by precisely tailoring pore surface chemistries and pore geometries6,11–17, a single system capable of controlling complex, selective multiphase transport has remained a distant prospect, and foulingmore » is nearly inevitable.Here we introduce a gating mechanism that uses a capillary-stabilized liquid as a reversible, reconfigurable gate that fills and seals pores in the closed state, and creates a non-fouling, liquid-lined pore in the open state.Theoretical modelling and experiments demonstrate that for each transport substance, the gating threshold—the pressure needed to open the pores—can be rationally tuned over a wide pressure range. This enables us to realize in one system differential response profiles for a variety of liquids and gases, even letting liquids flow through the pore while preventing gas from escaping.These capabilities allow us to dynamically modulate gas–liquid sorting in a microfluidic flow and to separate a three-phase air water–oil mixture, with the liquid lining ensuring sustained antifouling behaviour. Because the liquid gating strategy enables efficient long-term operation and can be applied to a variety of pore structures and membrane materials, and to micro- as well as macroscale fluid systems, we expect it to prove useful in a wide range of applications.« less

  6. Liquid-based gating mechanism with tunable multiphase selectivity and antifouling behaviour

    NASA Astrophysics Data System (ADS)

    Hou, Xu; Hu, Yuhang; Grinthal, Alison; Khan, Mughees; Aizenberg, Joanna

    2015-03-01

    Living organisms make extensive use of micro- and nanometre-sized pores as gatekeepers for controlling the movement of fluids, vapours and solids between complex environments. The ability of such pores to coordinate multiphase transport, in a highly selective and subtly triggered fashion and without clogging, has inspired interest in synthetic gated pores for applications ranging from fluid processing to 3D printing and lab-on-chip systems. But although specific gating and transport behaviours have been realized by precisely tailoring pore surface chemistries and pore geometries, a single system capable of controlling complex, selective multiphase transport has remained a distant prospect, and fouling is nearly inevitable. Here we introduce a gating mechanism that uses a capillary-stabilized liquid as a reversible, reconfigurable gate that fills and seals pores in the closed state, and creates a non-fouling, liquid-lined pore in the open state. Theoretical modelling and experiments demonstrate that for each transport substance, the gating threshold--the pressure needed to open the pores--can be rationally tuned over a wide pressure range. This enables us to realize in one system differential response profiles for a variety of liquids and gases, even letting liquids flow through the pore while preventing gas from escaping. These capabilities allow us to dynamically modulate gas-liquid sorting in a microfluidic flow and to separate a three-phase air-water-oil mixture, with the liquid lining ensuring sustained antifouling behaviour. Because the liquid gating strategy enables efficient long-term operation and can be applied to a variety of pore structures and membrane materials, and to micro- as well as macroscale fluid systems, we expect it to prove useful in a wide range of applications.

  7. Liquid-based gating mechanism with tunable multiphase selectivity and antifouling behaviour

    SciTech Connect

    Hou, X; Hu, YH; Grinthal, A; Khan, M; Aizenberg, J

    2015-03-04

    Living organisms make extensive use of micro- and nanometre-sized pores as gatekeepers for controlling the movement of fluids, vapours and solids between complex environments. The ability of such pores to coordinate multiphase transport, in a highly selective and subtly triggered fashion and without clogging, has inspired interest in synthetic gated pores for applications ranging from fluid processing to 3D printing and lab-on-chip systems(1-10). But although specific gating and transport behaviours have been realized by precisely tailoring pore surface chemistries and pore geometries(6,11-17), a single system capable of controlling complex, selective multiphase transport has remained a distant prospect, and fouling is nearly inevitable(11,12). Here we introduce a gating mechanism that uses a capillary-stabilized liquid as a reversible, reconfigurable gate that fills and seals pores in the closed state, and creates a non-fouling, liquid-lined pore in the open state. Theoretical modelling and experiments demonstrate that for each transport substance, the gating threshold-the pressure needed to open the pores-can be rationally tuned over a wide pressure range. This enables us to realize in one system differential response profiles for a variety of liquids and gases, even letting liquids flow through the pore while preventing gas from escaping. These capabilities allow us to dynamically modulate gas-liquid sorting in a microfluidic flow and to separate a three-phase air-water-oil mixture, with the liquid lining ensuring sustained antifouling behaviour. Because the liquid gating strategy enables efficient long-term operation and can be applied to a variety of pore structures and membrane materials, and to micro- as well as macroscale fluid systems, we expect it to prove useful in a wide range of applications.

  8. Multiphase Flow in Micro-fracture Junctions

    NASA Astrophysics Data System (ADS)

    Basagaoglu, H.; Meakin, P.; Succi, S.; Wildenschild, D.

    2005-12-01

    A two-dimensional two-phase lattice-Boltzmann model was used to simulate immiscible fluid flow in four micro-fracture geometries closely related to geological fractured systems: (1) a fracture junction with fractal surfaces embedded in a non-porous matrix; (2) a fracture junction embedded in a heterogeneous porous matrix; (3) a heterogeneous porous medium overlying a fracture with fractal surfaces; and (4) a fracture network with fractal surfaces enclosed by a non-porous medium. The spatio-temporal distributions of fluids in fracture junctions were controlled by interplays between velocity-dependent contact angle dynamics, mediated by surface roughness, and pore-scale gravitational, viscous, and capillary forces. All simulations were conducted with actual physical units. Sensitivities of lateral and vertical spreads of fluids in the fracture junctions to the orientation of fracture junctions (tilted vs. vertical) and the wetting strength of fluids were analyzed via temporal moment analyses for the first two geometries. The simulation results revealed that the receding and advancing contact angles varied strongly with the transient fluid velocity. The patterns and distributions of thin films (continuous vs. discontinuous) on rough fracture walls were largely controlled by the wetting strength of the fluids. The spatio-temporal distributions of fluids were highly sensitive to the domain size and boundary conditions (periodic, no-flow, constant density, and flux-type). Single- and two-sided wetting of fracture aperture walls and long-term entrapment of a nonwetting less-dense fluid by a wetting dense fluid were observed in the simulations. These numerical results are useful for the design of experiments and for analyzing the relative strengths of pore-scale processes in more complex and realistic fracture systems such as those encountered at the Yucca Mountain and Idaho National Laboratory sites.

  9. Multiphase Turbulent Interstellar Medium: Some Recent Results from Radio Astronomy

    NASA Astrophysics Data System (ADS)

    Roy, Nirupam

    2015-06-01

    The radio frequency 1.4 GHz transition of the atomic hydrogen is one of the important tracers of the diffuse neutral interstellar medium. Radio astronomical observations of this transition, using either a single dish telescope or an array interferometer, reveal different properties of the interstellar medium. Such observations are particularly useful to study the multiphase nature and turbulence in the interstellar gas. Observations with multiple radio telescopes have recently been used to study these two closely related aspects in greater detail. This review article presents a brief outline of some of the basic ideas of radio astronomical observations and data analysis, summarizes the results from these recent observations, and discusses possible implications of the results. Using various observational techniques, the density and the velocity fluctuations in the Galactic interstellar medium was found to have a Kolmogorov-like power law power spectra. The observed power law scaling of the turbulent velocity dispersion with the length scale can be used to derive the true temperature distribution of the medium. Observations from a large ongoing atomic hydrogen absorption line survey have also been used to study the distribution of gas at different temperature. The thermal steady state model predicts that the multiphase neutral gas will exist in cold and warm phase with temperature below 200 K and above 5000 K respectively. However, these observations clearly show the presence of a large fraction of gas in the intermediate unstable phase. These results raise serious doubt about the validity of the standard model, and highlight the necessity of alternative theoretical models. Interestingly, numerical simulations suggest that some of the observational results can be explained consistently by including the effects of turbulence in the models of the multiphase medium.

  10. Impact of normal stress on multiphase flow through rough fractures

    NASA Astrophysics Data System (ADS)

    Alves da Silva Junior, J.; Kang, P. K.; Yang, Z.; Cueto-Felgueroso, L.; Juanes, R.

    2015-12-01

    Fluid flow and transport through geologic fractures plays a key role in several areas such as groundwater hydrology, geothermal energy, oil and gas production, CO2 sequestration and nuclear waste disposal. High-permeability zones associated with fracture corridors often serve as fast fluid conduits for both single and multiphase flow in otherwise low-permeability media. When multiphase flow occurs, the presence of one phase interferes with the flow of the other phase, resulting in complex displacement patterns through the fracture, and macroscopic descriptors (such as fracture-scale capillary pressure and relative permeability) that depend on the phase concentration of both phases. Here, we investigate the impact of normal stress on single and multiphase flow through rough-walled fractures: (1) we generate synthetic aperture fields that honor the fractal roughness structure observed in real fractures; (2) we model the effect of normal stress on the fracture aperture geometry by solving the contact problem between fracture walls; and (3) we use invasion percolation with trapping to model immiscible fluid displacement and then compute relative permeability numerically for each stress scenario. Our results indicate that normal stress increases the amount of contact area in the fracture wall, which results in an increase of the tortuosity of the available path for fluid displacement. Increasing normal stress results in low relative permeability for the wetting phase due to a decrease of the available path for fluid flow, and therefore a small amount of non-wetting fluid has a large impact on the flow of the wetting fluid. We find that the relative permeability of the non-wetting fluid shows less variation with stress than the wetting fluid, and that both fluids exhibit strong phase interference at intermediate saturations. Finally, we show early results from our experimental work currently underway to validate the modeling results.

  11. Multiphase modeling of geologic carbon sequestration in saline aquifers.

    PubMed

    Bandilla, Karl W; Celia, Michael A; Birkholzer, Jens T; Cihan, Abdullah; Leister, Evan C

    2015-01-01

    Geologic carbon sequestration (GCS) is being considered as a climate change mitigation option in many future energy scenarios. Mathematical modeling is routinely used to predict subsurface CO2 and resident brine migration for the design of injection operations, to demonstrate the permanence of CO2 storage, and to show that other subsurface resources will not be degraded. Many processes impact the migration of CO2 and brine, including multiphase flow dynamics, geochemistry, and geomechanics, along with the spatial distribution of parameters such as porosity and permeability. In this article, we review a set of multiphase modeling approaches with different levels of conceptual complexity that have been used to model GCS. Model complexity ranges from coupled multiprocess models to simplified vertical equilibrium (VE) models and macroscopic invasion percolation models. The goal of this article is to give a framework of conceptual model complexity, and to show the types of modeling approaches that have been used to address specific GCS questions. Application of the modeling approaches is shown using five ongoing or proposed CO2 injection sites. For the selected sites, the majority of GCS models follow a simplified multiphase approach, especially for questions related to injection and local-scale heterogeneity. Coupled multiprocess models are only applied in one case where geomechanics have a strong impact on the flow. Owing to their computational efficiency, VE models tend to be applied at large scales. A macroscopic invasion percolation approach was used to predict the CO2 migration at one site to examine details of CO2 migration under the caprock.

  12. Multi-phase Thermohaline Convection in Porous Media

    NASA Astrophysics Data System (ADS)

    Geiger, S.; Driesner, T.; Matthai, S. K.; Heinrich, C. A.

    2003-12-01

    The simultaneous motion of heat and dissolved solutes by aqueous or magmatic fluids through porous or fractured media within the earth's crust is a key factor that drives many important geological processes, such as the formation of large ore deposits, cooling of new-formed oceanic crust along mid-ocean ridges, metamorphism, or the evolution of geothermal systems. The motion of such crustal fluids is usually dominated by convection due to density differences within the fluids that arise from pressure, temperature and compositional variations present in the fluids. Oxygen isotope data and fluid inclusion data indicate that fluids may percolate down to 15 km depth and experience temperatures exceeding 700 {o}C. Although crustal fluids commonly contain various dissolved chemical components and gases, the most abundant solute is salt, i.e. NaCl. Hence, changes in the concentration of NaCl influence the density variations of crustal fluids the most. The presence of NaCl in H2O has decisive effects on the thermodynamics and hydrodynamics of crustal fluids. NaCl-H2O fluids can boil and separate into a high-density brine and low-salinity vapor at much higher temperatures and pressures than the critical temperature and pressure for pure H2O. NaCl-H2O fluids may also become saturated with respect to NaCl such that a solid NaCl phase coexists with a liquid or vapor fluid phase. Because salt advects faster than heat but diffuses slower than heat, the resulting double-diffusive and double-convective motion of salt and heat may lead to non-linear flow instabilities such as periodic or chaotic behavior. While many studies have addressed the theory of convection driven by temperature and/or salinity gradients, they were limited to a Boussinesq approximation and neglected phase separation. In this study we have numerically examined the behavior of multi-phase thermohaline convection in a porous media heated and salted from below using a novel finite element - finite volume

  13. MAMAP - a new spectrometer system for column-averaged methane and carbon dioxide observations from aircraft: instrument description and performance assessment

    NASA Astrophysics Data System (ADS)

    Gerilowski, K.; Tretner, A.; Krings, T.; Buchwitz, M.; Bertagnolio, P. P.; Belemezov, F.; Erzinger, J.; Burrows, J. P.; Bovensmann, H.

    2010-08-01

    Carbon dioxide (CO2) and Methane (CH4) are the two most important anthropogenic greenhouse gases. CH4 is furthermore one of the most potent present and future contributors to global warming because of its large global warming potential (GWP). Our knowledge of CH4 sources and sinks is based primarily on sparse in-situ local point measurements from micro sites and surface networks and more recently on low spatial resolution satellite observations. There is a need for measurements of the dry columns of CO2 and CH4 having high spatial resolution and spatial coverage. In order to fill this gap a new passive airborne 2-channel grating spectrometer instrument for remote sensing of small scale and mesoscale column-averaged CH4 and CO2 observations has been developed. This Methane Airborne MAPper (MAMAP) instrument measures reflected and scattered solar radiation in the short wave infrared (SWIR) and near-infrared (NIR) parts of the electro-magnetic spectrum at moderate spectral resolution. The SWIR channel yields measurements of atmospheric absorption bands of CH4 and CO2 in the spectral range between 1.59 and 1.69 μm at a spectral resolution of 0.82 nm. The NIR channel around 0.76 μm measures the atmospheric O2-A-band absorption with a resolution of 0.46 nm. MAMAP has been designed for flexible operation aboard a variety of airborne platforms. The instrument design and performance, together with some results from on-ground and in-flight engineering tests are presented. The instrument performance has been analyzed using a retrieval algorithm applied to the SWIR channel nadir measured spectra. The signal-to-noise ratio (SNR) of the SWIR channel is approximately 1000 for integration times (tint) in the range of 0.6-0.8 s for scenes with surface spectral reflectances of around 0.18. At these integration times the ground scene size is about 23×33 m2 for an aircraft altitude of 1 km and a ground speed of 200 km/h. For these scenes the CH4 and CO2 column retrieval precisions

  14. Characterizing the stretch-flangeability of hot rolled multiphase steels

    SciTech Connect

    Pathak, N.; Butcher, C.; Worswick, M.; Gao, J.

    2013-12-16

    Hole expansion tests are commonly used to characterize the edge stretching limit of a material. Traditionally, a conical punch is used to expand a punched hole until a through-thickness crack appears. However, many automotive stretch flanging operations involve in-plane edge stretching that is best captured with a flat punch. In this paper, hole expansion tests were carried out on two different hot-rolled multiphase steels using both flat and conical punches. The fracture mechanisms for both punch types were investigated using scanning electron microscopy (SEM)

  15. Numerical Simulation of Multiphase Flow in Solid Rocket Motors

    NASA Astrophysics Data System (ADS)

    Attili, A.; Favini, B.; Di Giacinto, M.; Serraglia, F.

    2009-01-01

    In the paper a general mathematical description of the flow in the internal chamber of solid rocket motors is presented. The formulation adopted take into account the multi-species and multiphase, reactive, multidimensional characteristics of the flow. The grain combustion is described by a pressure dependent law; aluminum droplet are modelled by a Lagrangian approach, coupled with the Eulerian formulation adopted for the gas phase. The mathematical model has been implemented in a simulation code and several simulations have been performed; in particular in the paper the re- sults for two geometries are described: a simple cylindrical port-area rocket and the Zefiro 9 SRM.

  16. AM363 martensitic stainless steel: A multiphase equation of state

    NASA Astrophysics Data System (ADS)

    De Lorenzi-Venneri, Giulia; Crockett, Scott D.

    2017-01-01

    A multiphase equation of state for stainless steel AM363 has been developed within the Opensesame approach and has been entered as material 4295 in the LANL-SESAME Library. Three phases were constructed separately: the low pressure martensitic phase, the austenitic phase and the liquid. Room temperature data and the explicit introduction of a magnetic contribution to the free energy determined the martensitic phase, while shock Hugoniot data was used to determine the austenitic phase and the phase boundaries. More experimental data or First Principles calculations would be useful to better characterize the liquid.

  17. The control method for the multi-phase traffic model

    NASA Astrophysics Data System (ADS)

    Liu, Yi; Cheng, Rong-Jun; Ma, Yan-Qiang; Ge, Hong-Xia

    2016-04-01

    Based on multi-phase car-following model proposed by Nagatani, the control theory method is used to analyze the stability of the model. The optimal velocity function is improved to have more turning points. The original optimal velocity with one turning point shows two-phase traffic, while the improved model with n turning points exhibits n+1 phase traffic. Control signal is added into the model. Numerical simulation is conducted to show the results for the stability of the model with and without control signal.

  18. Fault tolerant multiphase electrical drives: the impact of design

    NASA Astrophysics Data System (ADS)

    Semail, E.; Kestelyn, X.; Locment, F.

    2008-08-01

    This paper deals with fault tolerant multiphase electrical drives. The quality of the torque of a vector-controlled Permanent Magnet (PM) Synchronous Machine supplied by a multi-leg Voltage Source Inverter (VSI) is examined in normal operation and when one or two phases are open-circuited. It is then deduced that a seven-phase machine is a good compromise allowing high torque-to-volume density and easy control with smooth torque in fault operation. Experimental results confirm the predicted characteristics. This article has been submitted as part of “IET Colloquium on Reliability in Electromagnetic Systems”, 24 and 25 May 2007, Paris

  19. Modeling of Multiscale and Multiphase Phenomena in Materials Processing

    NASA Astrophysics Data System (ADS)

    Ludwig, Andreas; Kharicha, Abdellah; Wu, Menghuai

    2013-03-01

    In order to demonstrate how CFD can help scientists and engineers to better understand the fundamentals of engineering processes, a number of examples are shown and discussed. The paper covers (i) special aspects of continuous casting of steel including turbulence, motion and entrapment of non-metallic inclusions, and impact of soft reduction; (ii) multiple flow phenomena and multiscale aspects during casting of large ingots including flow-induced columnar-to-equiaxed transition and 3D formation of channel segregation; (iii) multiphase magneto-hydrodynamics during electro-slag remelting; and (iv) melt flow and solidification of thin but large centrifugal castings.

  20. Multiphase problems related to safety studies in the process industries

    NASA Astrophysics Data System (ADS)

    Baron, R. Grollier

    Safety risk and analysis, particularly in the petrochemical industry, are discussed. Multiphase flow problems resulting from loss of confinement are described: rupture of long pipes used for transporting liquefied gas; rupture of short pipes and branch connections in an installation; rupture of a container holding liquefied gas or another liquid at a temperature higher than its normal boiling temperature; and rupture of a container holding gas in the supercritical state. Operation of valves and rupture disks during reaction runaway; and artificial dispersion of gas layers are considered.