Williams Element with Generalized Degrees of Freedom for Fracture Analysis of Multiple-Cracked Beam

NASA Astrophysics Data System (ADS)

Xu, Hua; Wei, Quyang; Yang, Lufeng

2017-10-01

In this paper, the method of finite element with generalized degrees of freedom (FEDOFs) is used to calculate the stress intensity factor (SIF) of multiple cracked beam and analysed the effect of minor cracks on the main crack SIF in different cases. Williams element is insensitive to the size of singular region. So that calculation efficiency is highly improved. Examples analysis validates that the SIF near the crack tip can be obtained directly though FEDOFs. And the result is well consistent with ANSYS solution and has a satisfied accuracy.

A comparison of quality of present-day heat flow obtained from BHTs, Horner Plots of Malay Basin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Waples, D.W.; Mahadir, R.

1994-07-01

Reconciling temperature data obtained from measurement of single BHT, multiple BHT at a single depth, RFTs, and DSTs, is very difficult. Quality of data varied widely, however DST data were assumed to be most reliable. Data from 87 wells was used in this study, but only 47 wells have DST data. BASINMOD program was used to calculate the present-day heat flow, using measured thermal conductivity and calibrated against the DST data. The heat flows obtained from the DST data were assumed to be correct and representative throughout the basin. Then, heat flows using (1) uncorrected RFT data, (2) multiple BHTmore » data corrected by the Horner plot method, and (3) single BHT values corrected upward by a standard 10% were calculated. All of these three heat-flow populations had identically standard deviations to that for the DST data, but with significantly lower mean values. Correction factors were calculated to give each of the three erroneous populations the same mean value as the DST population. Heat flows calculated from RFT data had to be corrected upward by a factor of 1.12 to be equivalent to DST data; Horner plot data corrected by a factor of 1.18, and single BHT data by a factor of 1.2. These results suggest that present-day subsurface temperatures using RFT, Horner plot, and BHT data are considerably lower than they should be. The authors suspect qualitatively similar results would be found in other areas. Hence, they recommend significant corrections be routinely made until local calibration factors are established.« less

Estimation of effective dose and lifetime attributable risk from multiple head CT scans in ventriculoperitoneal shunted children.

PubMed

Aw-Zoretic, J; Seth, D; Katzman, G; Sammet, S

2014-10-01

The purpose of this review is to determine the averaged effective dose and lifetime attributable risk factor from multiple head computed tomography (CT) dose data on children with ventriculoperitoneal shunts (VPS). A total of 422 paediatric head CT exams were found between October 2008 and January 2011 and retrospectively reviewed. The CT dose data was weighted with the latest IRCP 103 conversion factor to obtain the effective dose per study and the averaged effective dose was calculated. Estimates of the lifetime attributable risk were also calculated from the averaged effective dose using a conversion factor from the latest BEIR VII report. Our study found the highest effective doses in neonates and the lowest effective doses were observed in the 10-18 years age group. We estimated a 0.007% potential increase risk in neonates and 0.001% potential increased risk in teenagers over the base risk. Multiple head CTs in children equates to a slight potential increase risk in lifetime attributable risk over the baseline risk for cancer, slightly higher in neonates relative to teenagers. The potential risks versus clinical benefit must be assessed. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Three-dimensional weight-accumulation algorithm for generating multiple excitation spots in fast optical stimulation

NASA Astrophysics Data System (ADS)

Takiguchi, Yu; Toyoda, Haruyoshi

2017-11-01

We report here an algorithm for calculating a hologram to be employed in a high-access speed microscope for observing sensory-driven synaptic activity across all inputs to single living neurons in an intact cerebral cortex. The system is based on holographic multi-beam generation using a two-dimensional phase-only spatial light modulator to excite multiple locations in three dimensions with a single hologram. The hologram was calculated with a three-dimensional weighted iterative Fourier transform method using the Ewald sphere restriction to increase the calculation speed. Our algorithm achieved good uniformity of three dimensionally generated excitation spots; the standard deviation of the spot intensities was reduced by a factor of two compared with a conventional algorithm.

Three-dimensional weight-accumulation algorithm for generating multiple excitation spots in fast optical stimulation

NASA Astrophysics Data System (ADS)

Takiguchi, Yu; Toyoda, Haruyoshi

2018-06-01

We report here an algorithm for calculating a hologram to be employed in a high-access speed microscope for observing sensory-driven synaptic activity across all inputs to single living neurons in an intact cerebral cortex. The system is based on holographic multi-beam generation using a two-dimensional phase-only spatial light modulator to excite multiple locations in three dimensions with a single hologram. The hologram was calculated with a three-dimensional weighted iterative Fourier transform method using the Ewald sphere restriction to increase the calculation speed. Our algorithm achieved good uniformity of three dimensionally generated excitation spots; the standard deviation of the spot intensities was reduced by a factor of two compared with a conventional algorithm.

Validation of DRAGON4/DONJON4 simulation methodology for a typical MNSR by calculating reactivity feedback coefficient and neutron flux

NASA Astrophysics Data System (ADS)

Al Zain, Jamal; El Hajjaji, O.; El Bardouni, T.; Boukhal, H.; Jaï, Otman

2018-06-01

The MNSR is a pool type research reactor, which is difficult to model because of the importance of neutron leakage. The aim of this study is to evaluate a 2-D transport model for the reactor compatible with the latest release of the DRAGON code and 3-D diffusion of the DONJON code. DRAGON code is then used to generate the group macroscopic cross sections needed for full core diffusion calculations. The diffusion DONJON code, is then used to compute the effective multiplication factor (keff), the feedback reactivity coefficients and neutron flux which account for variation in fuel and moderator temperatures as well as the void coefficient have been calculated using the DRAGON and DONJON codes for the MNSR research reactor. The cross sections of all the reactor components at different temperatures were generated using the DRAGON code. These group constants were used then in the DONJON code to calculate the multiplication factor and the neutron spectrum at different water and fuel temperatures using 69 energy groups. Only one parameter was changed where all other parameters were kept constant. Finally, Good agreements between the calculated and measured have been obtained for every of the feedback reactivity coefficients and neutron flux.

Influence of multiple scattering on CloudSat measurements in snow: A model study

NASA Astrophysics Data System (ADS)

Matrosov, Sergey Y.; Battaglia, Alessandro

2009-06-01

The effects of multiple scattering on larger precipitating hydrometers have an influence on measurements of the spaceborne W-band (94 GHz) CloudSat radar. This study presents initial quantitative estimates of these effects in “dry” snow using radiative transfer calculations for appropriate snowfall models. It is shown that these effects become significant (i.e., greater than approximately 1 dB) when snowfall radar reflectivity factors are greater than about 10-15 dBZ. Reflectivity enhancement due to multiple scattering can reach 4-5 dB in heavier stratiform snowfalls. Multiple scattering effects counteract signal attenuation, so the observed CloudSat reflectivity factors in snowfall could be relatively close to the values that would be observed in the case of single scattering and the absence of attenuation.

Upper Gastrointestinal Complications and Cardiovascular/Gastrointestinal Risk Calculator in Patients with Myocardial Infarction Treated with Aspirin.

PubMed

Wen, Lei

2017-08-20

Aspirin is widely used for the prevention of cardiovascular and cerebrovascular diseases for the past few years. However, much attention has been paid to the adverse effects associated with aspirin such as gastrointestinal bleeding. How to weigh the benefits and hazards? The current study aimed to assess the feasibility of a cardiovascular/gastrointestinal risk calculator, AsaRiskCalculator, in predicting gastrointestinal events in Chinese patients with myocardial infarction (MI), determining unique risk factor(s) for gastrointestinal events to be considered in the calculator. The MI patients who visited Shapingba District People's Hospital between January 2012 and January 2016 were retrospectively reviewed. Based on gastroscopic data, the patients were divided into two groups: gastrointestinal and nongastrointestinal groups. Demographic and clinical data of the patients were then retrieved for statistical analysis. Univariate and multiple logistic regression analyses were used to identify independent risk factors for gastrointestinal events. The receiver operating characteristic (ROC) curves were used to assess the predictive value of AsaRiskCalculator for gastrointestinal events. A total of 400 MI patients meeting the eligibility criteria were analyzed, including 94 and 306 in the gastrointestinal and nongastrointestinal groups, respectively. The data showed that age, male gender, predicted gastrointestinal events, and Helicobacter pylori (HP) infection were positively correlated with gastrointestinal events. In multiple logistic regression analysis, predicted gastrointestinal events and HP infection were identified as risk factors for actual gastrointestinal events. HP infection was highly predictive in Chinese patients; the ROC curve indicated an area under the curve of 0.822 (95% confidence interval: 0.774-0.870). The best diagnostic cutoff point of predicted gastrointestinal events was 68.0‰, yielding sensitivity and specificity of 60.6% and 93.1%, respectively, for predicting gastrointestinal events in Chinese patients with MI. AsaRiskCalculator had a predictive value for gastrointestinal events in Chinese patients with MI. HP infection seemed to be an independent risk factor for gastrointestinal events caused by long-term aspirin treatment in Chinese patients with MI, and it should be included in the risk calculator adapted for Chinese patients.

Development of a software based automatic exposure control system for use in image guided radiation therapy

NASA Astrophysics Data System (ADS)

Morton, Daniel R.

Modern image guided radiation therapy involves the use of an isocentrically mounted imaging system to take radiographs of a patient's position before the start of each treatment. Image guidance helps to minimize errors associated with a patients setup, but the radiation dose received by patients from imaging must be managed to ensure no additional risks. The Varian On-Board Imager (OBI) (Varian Medical Systems, Inc., Palo Alto, CA) does not have an automatic exposure control system and therefore requires exposure factors to be manually selected. Without patient specific exposure factors, images may become saturated and require multiple unnecessary exposures. A software based automatic exposure control system has been developed to predict optimal, patient specific exposure factors. The OBI system was modelled in terms of the x-ray tube output and detector response in order to calculate the level of detector saturation for any exposure situation. Digitally reconstructed radiographs are produced via ray-tracing through the patients' volumetric datasets that are acquired for treatment planning. The ray-trace determines the attenuation of the patient and subsequent x-ray spectra incident on the imaging detector. The resulting spectra are used in the detector response model to determine the exposure levels required to minimize detector saturation. Images calculated for various phantoms showed good agreement with the images that were acquired on the OBI. Overall, regions of detector saturation were accurately predicted and the detector response for non-saturated regions in images of an anthropomorphic phantom were calculated to generally be within 5 to 10 % of the measured values. Calculations were performed on patient data and found similar results as the phantom images, with the calculated images being able to determine detector saturation with close agreement to images that were acquired during treatment. Overall, it was shown that the system model and calculation method could potentially be used to predict patients' exposure factors before their treatment begins, thus preventing the need for multiple exposures.

Casimir meets Poisson: improved quark/gluon discrimination with counting observables

DOE PAGES

Frye, Christopher; Larkoski, Andrew J.; Thaler, Jesse; ...

2017-09-19

Charged track multiplicity is among the most powerful observables for discriminating quark- from gluon-initiated jets. Despite its utility, it is not infrared and collinear (IRC) safe, so perturbative calculations are limited to studying the energy evolution of multiplicity moments. While IRC-safe observables, like jet mass, are perturbatively calculable, their distributions often exhibit Casimir scaling, such that their quark/gluon discrimination power is limited by the ratio of quark to gluon color factors. In this paper, we introduce new IRC-safe counting observables whose discrimination performance exceeds that of jet mass and approaches that of track multiplicity. The key observation is that trackmore » multiplicity is approximately Poisson distributed, with more suppressed tails than the Sudakov peak structure from jet mass. By using an iterated version of the soft drop jet grooming algorithm, we can define a “soft drop multiplicity” which is Poisson distributed at leading-logarithmic accuracy. In addition, we calculate the next-to-leading-logarithmic corrections to this Poisson structure. If we allow the soft drop groomer to proceed to the end of the jet branching history, we can define a collinear-unsafe (but still infrared-safe) counting observable. Exploiting the universality of the collinear limit, we define generalized fragmentation functions to study the perturbative energy evolution of collinear-unsafe multiplicity.« less

Casimir meets Poisson: improved quark/gluon discrimination with counting observables

DOE Office of Scientific and Technical Information (OSTI.GOV)

Frye, Christopher; Larkoski, Andrew J.; Thaler, Jesse

Charged track multiplicity is among the most powerful observables for discriminating quark- from gluon-initiated jets. Despite its utility, it is not infrared and collinear (IRC) safe, so perturbative calculations are limited to studying the energy evolution of multiplicity moments. While IRC-safe observables, like jet mass, are perturbatively calculable, their distributions often exhibit Casimir scaling, such that their quark/gluon discrimination power is limited by the ratio of quark to gluon color factors. In this paper, we introduce new IRC-safe counting observables whose discrimination performance exceeds that of jet mass and approaches that of track multiplicity. The key observation is that trackmore » multiplicity is approximately Poisson distributed, with more suppressed tails than the Sudakov peak structure from jet mass. By using an iterated version of the soft drop jet grooming algorithm, we can define a “soft drop multiplicity” which is Poisson distributed at leading-logarithmic accuracy. In addition, we calculate the next-to-leading-logarithmic corrections to this Poisson structure. If we allow the soft drop groomer to proceed to the end of the jet branching history, we can define a collinear-unsafe (but still infrared-safe) counting observable. Exploiting the universality of the collinear limit, we define generalized fragmentation functions to study the perturbative energy evolution of collinear-unsafe multiplicity.« less

Comparing Institution Nitrogen Footprints: Metrics for Assessing and Tracking Environmental Impact

PubMed Central

Leach, Allison M.; Compton, Jana E.; Galloway, James N.; Andrews, Jennifer

2017-01-01

Abstract When multiple institutions with strong sustainability initiatives use a new environmental impact assessment tool, there is an impulse to compare. The first seven institutions to calculate nitrogen footprints using the Nitrogen Footprint Tool have worked collaboratively to improve calculation methods, share resources, and suggest methods for reducing their footprints. This article compares those seven institutions’ results to reveal the common and unique drivers of institution nitrogen footprints. The footprints were compared by scope and sector, and the results were normalized by multiple factors (e.g., population, amount of food served). The comparisons found many consistencies across the footprints, including the large contribution of food. The comparisons identified metrics that could be used to track progress, such as an overall indicator for the nitrogen sustainability of food purchases. The comparisons also pointed to differences in system bounds of the calculations, which are important to standardize when comparing across institutions. The footprints were influenced by factors both within and outside of the institutions’ ability to control, such as size, location, population, and campus use. However, these comparisons also point to a pathway forward for standardizing nitrogen footprint tool calculations, identifying metrics that can be used to track progress, and determining a sustainable institution nitrogen footprint. PMID:29350218

Comparing Institution Nitrogen Footprints: Metrics for ...

EPA Pesticide Factsheets

When multiple institutions with strong sustainability initiatives use a new environmental impact assessment tool, there is an impulse to compare. The first seven institutions to calculate their nitrogen footprints using the nitrogen footprint tool have worked collaboratively to improve calculation methods, share resources, and suggest methods for reducing their footprints. This paper compares the results of those seven results to reveal the common and unique drivers of institution nitrogen footprints. The footprints were compared by scope and sector, and the results were normalized by multiple factors (e.g., population, number of meals served). The comparisons found many consistencies across the footprints, including the large contribution of food. The comparisons identified metrics that could be used to track progress, such as an overall indicator for the nitrogen sustainability of food purchases. The results also found differences in system bounds of the calculations, which are important to standardize when comparing across institutions. The footprints were influenced by factors that are both within and outside of the institutions’ ability to control, such as size, location, population, and campus use. However, these comparisons also point to a pathway forward for standardizing nitrogen footprint tool calculations, identifying metrics that can be used to track progress, and determining a sustainable institution nitrogen footprint. This paper is being submitt

Comparative study on neutronics characteristics of a 1500 MWe metal fuel sodium-cooled fast reactor

DOE PAGES

Ohgama, Kazuya; Aliberti, Gerardo; Stauff, Nicolas E.; ...

2017-02-28

Under the cooperative effort of the Civil Nuclear Energy R&D Working Group within the framework of the U.S.-Japan bilateral, Argonne National Laboratory (ANL) and Japan Atomic Energy Agency (JAEA) have been performing benchmark study using Japan Sodium-cooled Fast Reactor (JSFR) design with metal fuel. In this benchmark study, core characteristic parameters at the beginning of cycle were evaluated by the best estimate deterministic and stochastic methodologies of ANL and JAEA. The results obtained by both institutions show a good agreement with less than 200 pcm of discrepancy on the neutron multiplication factor, and less than 3% of discrepancy on themore » sodium void reactivity, Doppler reactivity, and control rod worth. The results by the stochastic and deterministic approaches were compared in each party to investigate impacts of the deterministic approximation and to understand potential variations in the results due to different calculation methodologies employed. From the detailed analysis of methodologies, it was found that the good agreement in multiplication factor from the deterministic calculations comes from the cancellation of the differences on the methodology (0.4%) and nuclear data (0.6%). The different treatment in reflector cross section generation was estimated as the major cause of the discrepancy between the multiplication factors by the JAEA and ANL deterministic methodologies. Impacts of the nuclear data libraries were also investigated using a sensitivity analysis methodology. Furthermore, the differences on the inelastic scattering cross sections of U-238, ν values and fission cross sections of Pu-239 and µ-average of Na-23 are the major contributors to the difference on the multiplication factors.« less

Comparative study on neutronics characteristics of a 1500 MWe metal fuel sodium-cooled fast reactor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ohgama, Kazuya; Aliberti, Gerardo; Stauff, Nicolas E.

Under the cooperative effort of the Civil Nuclear Energy R&D Working Group within the framework of the U.S.-Japan bilateral, Argonne National Laboratory (ANL) and Japan Atomic Energy Agency (JAEA) have been performing benchmark study using Japan Sodium-cooled Fast Reactor (JSFR) design with metal fuel. In this benchmark study, core characteristic parameters at the beginning of cycle were evaluated by the best estimate deterministic and stochastic methodologies of ANL and JAEA. The results obtained by both institutions show a good agreement with less than 200 pcm of discrepancy on the neutron multiplication factor, and less than 3% of discrepancy on themore » sodium void reactivity, Doppler reactivity, and control rod worth. The results by the stochastic and deterministic approaches were compared in each party to investigate impacts of the deterministic approximation and to understand potential variations in the results due to different calculation methodologies employed. From the detailed analysis of methodologies, it was found that the good agreement in multiplication factor from the deterministic calculations comes from the cancellation of the differences on the methodology (0.4%) and nuclear data (0.6%). The different treatment in reflector cross section generation was estimated as the major cause of the discrepancy between the multiplication factors by the JAEA and ANL deterministic methodologies. Impacts of the nuclear data libraries were also investigated using a sensitivity analysis methodology. Furthermore, the differences on the inelastic scattering cross sections of U-238, ν values and fission cross sections of Pu-239 and µ-average of Na-23 are the major contributors to the difference on the multiplication factors.« less

A collision history-based approach to Sensitivity/Perturbation calculations in the continuous energy Monte Carlo code SERPENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Giuseppe Palmiotti

In this work, the implementation of a collision history-based approach to sensitivity/perturbation calculations in the Monte Carlo code SERPENT is discussed. The proposed methods allow the calculation of the eects of nuclear data perturbation on several response functions: the eective multiplication factor, reaction rate ratios and bilinear ratios (e.g., eective kinetics parameters). SERPENT results are compared to ERANOS and TSUNAMI Generalized Perturbation Theory calculations for two fast metallic systems and for a PWR pin-cell benchmark. New methods for the calculation of sensitivities to angular scattering distributions are also presented, which adopts fully continuous (in energy and angle) Monte Carlo estimators.

Impact of the neutron detector choice on Bell and Glasstone spatial correction factor for subcriticality measurement

NASA Astrophysics Data System (ADS)

Talamo, Alberto; Gohar, Y.; Cao, Y.; Zhong, Z.; Kiyavitskaya, H.; Bournos, V.; Fokov, Y.; Routkovskaya, C.

2012-03-01

In subcritical assemblies, the Bell and Glasstone spatial correction factor is used to correct the measured reactivity from different detector positions. In addition to the measuring position, several other parameters affect the correction factor: the detector material, the detector size, and the energy-angle distribution of source neutrons. The effective multiplication factor calculated by computer codes in criticality mode slightly differs from the average value obtained from the measurements in the different experimental channels of the subcritical assembly, which are corrected by the Bell and Glasstone spatial correction factor. Generally, this difference is due to (1) neutron counting errors; (2) geometrical imperfections, which are not simulated in the calculational model, and (3) quantities and distributions of material impurities, which are missing from the material definitions. This work examines these issues and it focuses on the detector choice and the calculation methodologies. The work investigated the YALINA Booster subcritical assembly of Belarus, which has been operated with three different fuel enrichments in the fast zone either: high (90%) and medium (36%), medium (36%), or low (21%) enriched uranium fuel.

The change of radial power factor distribution due to RCCA insertion at the first cycle core of AP1000

NASA Astrophysics Data System (ADS)

Susilo, J.; Suparlina, L.; Deswandri; Sunaryo, G. R.

2018-02-01

The using of a computer program for the PWR type core neutronic design parameters analysis has been carried out in some previous studies. These studies included a computer code validation on the neutronic parameters data values resulted from measurements and benchmarking calculation. In this study, the AP1000 first cycle core radial power peaking factor validation and analysis were performed using CITATION module of the SRAC2006 computer code. The computer code has been also validated with a good result to the criticality values of VERA benchmark core. The AP1000 core power distribution calculation has been done in two-dimensional X-Y geometry through ¼ section modeling. The purpose of this research is to determine the accuracy of the SRAC2006 code, and also the safety performance of the AP1000 core first cycle operating. The core calculations were carried out with the several conditions, those are without Rod Cluster Control Assembly (RCCA), by insertion of a single RCCA (AO, M1, M2, MA, MB, MC, MD) and multiple insertion RCCA (MA + MB, MA + MB + MC, MA + MB + MC + MD, and MA + MB + MC + MD + M1). The maximum power factor of the fuel rods value in the fuel assembly assumedapproximately 1.406. The calculation results analysis showed that the 2-dimensional CITATION module of SRAC2006 code is accurate in AP1000 power distribution calculation without RCCA and with MA+MB RCCA insertion.The power peaking factor on the first operating cycle of the AP1000 core without RCCA, as well as with single and multiple RCCA are still below in the safety limit values (less then about 1.798). So in terms of thermal power generated by the fuel assembly, then it can be considered that the AP100 core at the first operating cycle is safe.

An appraisal of statistical procedures used in derivation of reference intervals.

PubMed

Ichihara, Kiyoshi; Boyd, James C

2010-11-01

When conducting studies to derive reference intervals (RIs), various statistical procedures are commonly applied at each step, from the planning stages to final computation of RIs. Determination of the necessary sample size is an important consideration, and evaluation of at least 400 individuals in each subgroup has been recommended to establish reliable common RIs in multicenter studies. Multiple regression analysis allows identification of the most important factors contributing to variation in test results, while accounting for possible confounding relationships among these factors. Of the various approaches proposed for judging the necessity of partitioning reference values, nested analysis of variance (ANOVA) is the likely method of choice owing to its ability to handle multiple groups and being able to adjust for multiple factors. Box-Cox power transformation often has been used to transform data to a Gaussian distribution for parametric computation of RIs. However, this transformation occasionally fails. Therefore, the non-parametric method based on determination of the 2.5 and 97.5 percentiles following sorting of the data, has been recommended for general use. The performance of the Box-Cox transformation can be improved by introducing an additional parameter representing the origin of transformation. In simulations, the confidence intervals (CIs) of reference limits (RLs) calculated by the parametric method were narrower than those calculated by the non-parametric approach. However, the margin of difference was rather small owing to additional variability in parametrically-determined RLs introduced by estimation of parameters for the Box-Cox transformation. The parametric calculation method may have an advantage over the non-parametric method in allowing identification and exclusion of extreme values during RI computation.

Gauge invariance and kaon production in deep inelastic scattering at low scales

NASA Astrophysics Data System (ADS)

Guerrero, Juan V.; Accardi, Alberto

2018-06-01

This paper focuses on hadron mass effects in calculations of semi-inclusive kaon production in lepton-Deuteron deeply inelastic scattering at HERMES and COMPASS kinematics. In the collinear factorization framework, the corresponding cross section is shown to factorize, at leading order and leading twist, into products of parton distributions and fragmentation functions evaluated in terms of kaon- and nucleon-mass-dependent scaling variables, and to respect gauge invariance. It is found that hadron mass corrections for integrated kaon multiplicities sizeably reduce the apparent large discrepancy between measurements of K++K- multiplicities performed by the two collaborations, and fully reconcile their K+/K- ratios.

Analysis of a boron-carbide-drum-controlled critical reactor experiment

NASA Technical Reports Server (NTRS)

Mayo, W. T.

1972-01-01

In order to validate methods and cross sections used in the neutronic design of compact fast-spectrum reactors for generating electric power in space, an analysis of a boron-carbide-drum-controlled critical reactor was made. For this reactor the transport analysis gave generally satisfactory results. The calculated multiplication factor for the most detailed calculation was only 0.7-percent Delta k too high. Calculated reactivity worth of the control drums was $11.61 compared to measurements of $11.58 by the inverse kinetics methods and $11.98 by the inverse counting method. Calculated radial and axial power distributions were in good agreement with experiment.

Calculation of Stress Intensity Factors for Interfacial Cracks in Fiber Metal Laminates

NASA Technical Reports Server (NTRS)

Wang, John T.

2009-01-01

Stress intensity factors for interfacial cracks in Fiber Metal Laminates (FML) are computed by using the displacement ratio method recently developed by Sun and Qian (1997, Int. J. Solids. Struct. 34, 2595-2609). Various FML configurations with single and multiple delaminations subjected to different loading conditions are investigated. The displacement ratio method requires the total energy release rate, bimaterial parameters, and relative crack surface displacements as input. Details of generating the energy release rates, defining bimaterial parameters with anisotropic elasticity, and selecting proper crack surface locations for obtaining relative crack surface displacements are discussed in the paper. Even though the individual energy release rates are nonconvergent, mesh-size-independent stress intensity factors can be obtained. This study also finds that the selection of reference length can affect the magnitudes and the mode mixity angles of the stress intensity factors; thus, it is important to report the reference length used with the calculated stress intensity factors.

Eigentime identities for on weighted polymer networks

NASA Astrophysics Data System (ADS)

Dai, Meifeng; Tang, Hualong; Zou, Jiahui; He, Di; Sun, Yu; Su, Weiyi

2018-01-01

In this paper, we first analytically calculate the eigenvalues of the transition matrix of a structure with very complex architecture and their multiplicities. We call this structure polymer network. Based on the eigenvalues obtained in the iterative manner, we then calculate the eigentime identity. We highlight two scaling behaviors (logarithmic and linear) for this quantity, strongly depending on the value of the weight factor. Finally, by making use of the obtained eigenvalues, we determine the weighted counting of spanning trees.

Modeling, Materials, and Metrics: The Three-m Approach to FCS Signature Solutions

DTIC Science & Technology

2002-05-07

calculations. These multiple levels will be incorporated into the MuSES software. The four levels are described as follows: "* Radiosity - Deterministic...view-factor-based, all-diffuse solution. Very fast. Independent of user position. "* Directional Reflectivity - Radiosity with directional incident...target and environment facets (view factor with BRDF). Last ray cast bounce = radiosity solution. "* Multi-bounce path trace - Rays traced from observer

Ab Initio Calculation of XAFS Debye-Waller Factors for Crystalline Materials

NASA Astrophysics Data System (ADS)

Dimakis, Nicholas

2007-02-01

A direct an accurate technique for calculating the thermal X-ray absorption fine structure (XAFS) Debye-Waller factors (DWF) for materials of crystalline structure is presented. Using the Density Functional Theory (DFT) under the hybrid X3LYP functional, a library of MnO spin—optimized clusters are built and their phonon spectrum properties are calculated; these properties in the form of normal mode eigenfrequencies and eigenvectors are in turn used for calculation of the single and multiple scattering XAFS DWF. DWF obtained via this technique are temperature dependent expressions and can be used to substantially reduce the number of fitting parameters when experimental spectra are fitted with a hypothetical structure without any ad hoc assumptions. Due to the high computational demand a hybrid approach of mixing the DFT calculated DWF with the correlated Debye model for inner and outer shells respectively is presented. DFT obtained DWFs are compared with corresponding values from experimental XAFS spectra on manganosite. The cluster size effect and the spin parameter on the DFT calculated DWFs are discussed.

Simulation Analysis of the Mutual Influence of the Stress Intensity Factor on the Multiple Blisters Caused by Hydrogen Induced Damage

NASA Astrophysics Data System (ADS)

Ji, Congwei; Zhang, Shaojie; Wang, Hehui

2018-03-01

Hydrogen blisters are taken as the research object by using the finite element software ABAQUS. The stress intensity factors of blister cracks are numerically calculated at varying depths and different edge distances for established three-dimensional finite element models of single-blister and double-blisters, respectively. The mutual influence of the stress intensity factors of the multiple blisters is obtained. It shows that the blister crack is easier to expand when the crack is closer to inner wall of the cylinder. What’s more, the crack growth rate increases firstly and then decreases as the increasing of the distance between two blisters cracks. The investigated result is of great reference value for predicting the trend of blister crack growth.

Relativistic impulse approximation analysis of unstable calcium isotopes: {sup 60-74}Ca

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kaki, K.

2009-06-15

Recent relativistic mean-field calculations have provided nuclear distributions of Ca isotopes whose mass numbers are 60 through 74. We calculate observables of proton elastic scattering from these unstable isotopes and discuss relations between observables and nuclear distributions of such unstable nuclei. The calculations are based on relativistic impulse approximation (RIA) at incident proton energies from 100 through 500 MeV where predictions of RIA have been shown to provide good agreement with experimental data. To validate the use of optimal factorization and first-order calculations at these energies, contributions from the Fermi motion of the target nuclei and multiple scattering are estimatedmore » and compared with results calculated without these effects.« less

Gauge invariance and kaon production in deep inelastic scattering at low scales

DOE Office of Scientific and Technical Information (OSTI.GOV)

Guerrero, Juan V.; Accardi, Alberto

This work focuses on hadron mass effects in calculations of semi-inclusive kaon production in lepton-Deuteron deeply inelastic scattering at HERMES and COMPASS kinematics. In the collinear factorization framework, the corresponding cross section is shown to factorize, at leading order and leading twist, into products of parton distributions and fragmentation functions evaluated in terms of kaon- and nucleon-mass-dependent scaling variables, and to respect gauge invariance. It is found that hadron mass corrections for integrated kaon multiplicities sizeably reduce the apparent large discrepancy between measurements of K + + K - multiplicities performed by the two collaborations, and fully reconcile their Kmore » +/K - ratios.« less

Gauge invariance and kaon production in deep inelastic scattering at low scales

DOE PAGES

Guerrero, Juan V.; Accardi, Alberto

2018-06-08

This work focuses on hadron mass effects in calculations of semi-inclusive kaon production in lepton-Deuteron deeply inelastic scattering at HERMES and COMPASS kinematics. In the collinear factorization framework, the corresponding cross section is shown to factorize, at leading order and leading twist, into products of parton distributions and fragmentation functions evaluated in terms of kaon- and nucleon-mass-dependent scaling variables, and to respect gauge invariance. It is found that hadron mass corrections for integrated kaon multiplicities sizeably reduce the apparent large discrepancy between measurements of K + + K - multiplicities performed by the two collaborations, and fully reconcile their Kmore » +/K - ratios.« less

Verification of Three Dimensional Triangular Prismatic Discrete Ordinates Transport Code ENSEMBLE-TRIZ by Comparison with Monte Carlo Code GMVP

NASA Astrophysics Data System (ADS)

Homma, Yuto; Moriwaki, Hiroyuki; Ohki, Shigeo; Ikeda, Kazumi

2014-06-01

This paper deals with verification of three dimensional triangular prismatic discrete ordinates transport calculation code ENSEMBLE-TRIZ by comparison with multi-group Monte Carlo calculation code GMVP in a large fast breeder reactor. The reactor is a 750 MWe electric power sodium cooled reactor. Nuclear characteristics are calculated at beginning of cycle of an initial core and at beginning and end of cycle of equilibrium core. According to the calculations, the differences between the two methodologies are smaller than 0.0002 Δk in the multi-plication factor, relatively about 1% in the control rod reactivity, and 1% in the sodium void reactivity.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kalugin, A. V., E-mail: Kalugin-AV@nrcki.ru; Tebin, V. V.

The specific features of calculation of the effective multiplication factor using the Monte Carlo method for weakly coupled and non-asymptotic multiplying systems are discussed. Particular examples are considered and practical recommendations on detection and Monte Carlo calculation of systems typical in numerical substantiation of nuclear safety for VVER fuel management problems are given. In particular, the problems of the choice of parameters for the batch mode and the method for normalization of the neutron batch, as well as finding and interpretation of the eigenvalue spectrum for the integral fission matrix, are discussed.

Theoretical Studies on InGaAs/InAlAs SAGCM Avalanche Photodiodes

NASA Astrophysics Data System (ADS)

Cao, Siyu; Zhao, Yue; ur Rehman, Sajid; Feng, Shuai; Zuo, Yuhua; Li, Chuanbo; Zhang, Lichun; Cheng, Buwen; Wang, Qiming

2018-05-01

In this paper, we provide a detailed insight on InGaAs/InAlAs separate absorption, grading, charge, and multiplication avalanche photodiodes (SAGCM APDs) and a theoretical model of APDs is built. Through theoretical analysis and two-dimensional (2D) simulation, the influence of charge layer and tunneling effect on the APDs is fully understood. The design of charge layer (including doping level and thickness) can be calculated by our predictive model for different multiplication thickness. We find that as the thickness of charge layer increases, the suitable doping level range in charge layer decreases. Compared to thinner charge layer, performance of APD varies significantly via several percent deviations of doping concentrations in thicker charge layer. Moreover, the generation rate ( G btt ) of band-to-band tunnel is calculated, and the influence of tunneling effect on avalanche field was analyzed. We confirm that avalanche field and multiplication factor ( M n ) in multiplication will decrease by the tunneling effect. The theoretical model and analysis are based on InGaAs/InAlAs APD; however, they are applicable to other APD material systems as well.

The neural bases of the multiplication problem-size effect across countries

PubMed Central

Prado, Jérôme; Lu, Jiayan; Liu, Li; Dong, Qi; Zhou, Xinlin; Booth, James R.

2013-01-01

Multiplication problems involving large numbers (e.g., 9 × 8) are more difficult to solve than problems involving small numbers (e.g., 2 × 3). Behavioral research indicates that this problem-size effect might be due to different factors across countries and educational systems. However, there is no neuroimaging evidence supporting this hypothesis. Here, we compared the neural correlates of the multiplication problem-size effect in adults educated in China and the United States. We found a greater neural problem-size effect in Chinese than American participants in bilateral superior temporal regions associated with phonological processing. However, we found a greater neural problem-size effect in American than Chinese participants in right intra-parietal sulcus (IPS) associated with calculation procedures. Therefore, while the multiplication problem-size effect might be a verbal retrieval effect in Chinese as compared to American participants, it may instead stem from the use of calculation procedures in American as compared to Chinese participants. Our results indicate that differences in educational practices might affect the neural bases of symbolic arithmetic. PMID:23717274

Independence of heritable influences on the food intake of free-living humans.

PubMed

de Castro, John M

2002-01-01

The time of day of meal ingestion, the number of people present at the meal, the subjective state of hunger, and the estimated before-meal contents in the stomach have been established as influences on the amount eaten in a meal and these influences have been shown to be heritable. Because these factors intercorrelate, the calculated heritabilities for some of these variables might result indirectly from their covariation with one of the other heritable variables. The independence of the heritability of the influence of these four factors was investigated with 110 identical and 102 fraternal same-sex and 53 fraternal mixed-sex adult twin pairs who were paid to maintain 7-d food-intake diaries. From the diary reports, the meal sizes were calculated and subjected to multiple regression analysis using the estimated before-meal stomach contents, the reported number of other people present, the subjective hunger ratings, and the time of day of the meal as predictors. Linear structural modeling was applied to the beta-coefficients from the multiple regression to investigate whether the heritability of the influences of these four variables was independent. Significant genetic effects were found for the beta-coefficients for all four variables, indicating that the heritability of their relationship with intake is to some extent independent and heritable. This suggests that influences of multiple factors on intake are influenced by the genes and become part of the total package of genetically determined physiologic, sociocultural, and psychological processes that regulate energy balance.

Heritability of diurnal changes in food intake in free-living humans.

PubMed

de Castro, J M

2001-09-01

The time of day of meal ingestion, the number of people present at the meal, the subjective state of hunger, and the estimated before-meal contents in the stomach have been established as influences on the amount eaten in a meal, and this influence has been shown to be heritable. Because these factors intercorrelate, the possibility that the calculated heritabilities for some of these variables could result indirectly from their convariation with one of the other heritable variables was assessed. The independence of the heritability of the influence of these four factors was investigated with 110 identical and 102 fraternal same-sex and 53 fraternal mixed-sex adult twin pairs who were paid to maintain 7-d food intake diaries. From the diary reports, the meal sizes were calculated and subjected to multiple regression analysis using the estimated before-meal stomach contents, the reported number of other people present, the subjective hunger ratings, and the time of day of the meal as predictors. Linear structural modeling was applied to the beta coefficients from the multiple regression to investigate whether the heritability of the influences of these four variables was independent. Significant genetic effects were found for the beta coefficients for all four variables, indicating that the heritability of their relationship with intake is to some extent heritable. These results suggest that the influences of multiple factors on intake are influenced by the genes and become part of the total package of genetically determined physiologic, sociocultural, and psychological processes that regulate energy balance.

Λ b→pl⁻ν¯ l form factors from lattice QCD with static b quarks

DOE PAGES

Detmold, William; Lin, C.-J. David; Meinel, Stefan; ...

2013-07-23

We present a lattice QCD calculation of form factors for the decay Λ b→pμ⁻ν¯ μ, which is a promising channel for determining the Cabibbo-Kobayashi-Maskawa matrix element |V ub| at the Large Hadron Collider. In this initial study we work in the limit of static b quarks, where the number of independent form factors reduces to two. We use dynamical domain-wall fermions for the light quarks, and perform the calculation at two different lattice spacings and at multiple values of the light-quark masses in a single large volume. Using our form factor results, we calculate the Λ b→pμ⁻ν¯ μ differential decaymore » rate in the range 14 GeV²≤q²≤q² max, and obtain the integral ∫ q²max 14 GeV²[dΓ/dq²]dq²/|V ub|²=15.3±4.2 ps⁻¹. Combined with future experimental data, this will give a novel determination of |V ub| with about 15% theoretical uncertainty. The uncertainty is dominated by the use of the static approximation for the b quark, and can be reduced further by performing the lattice calculation with a more sophisticated heavy-quark action.« less

Interface and photoluminescence characteristics of graphene-(GaN/InGaN){sub n} multiple quantum wells hybrid structure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Liancheng, E-mail: wanglc@semi.ac.cn, E-mail: lzq@semi.ac.cn, E-mail: zh.zhang@hebut.edu.cn; Semiconductor Lighting Technology Research and Development Center, Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083; Mind Star

The effects of graphene on the optical properties of active system, e.g., the InGaN/GaN multiple quantum wells, are thoroughly investigated and clarified. Here, we have investigated the mechanisms accounting for the photoluminescence reduction for the graphene covered GaN/InGaN multiple quantum wells hybrid structure. Compared to the bare multiple quantum wells, the photoluminescence intensity of graphene covered multiple quantum wells showed a 39% decrease after excluding the graphene absorption losses. The responsible mechanisms have been identified with the following factors: (1) the graphene two dimensional hole gas intensifies the polarization field in multiple quantum wells, thus steepening the quantum well bandmore » profile and causing hole-electron pairs to further separate; (2) a lower affinity of graphene compared to air leading to a weaker capability to confine the excited hot electrons in multiple quantum wells; and (3) exciton transfer through non-radiative energy transfer process. These factors are theoretically analysed based on advanced physical models of semiconductor devices calculations and experimentally verified by varying structural parameters, such as the indium fraction in multiple quantum wells and the thickness of the last GaN quantum barrier spacer layer.« less

Cumulative Interference to Aircraft Radios from Multiple Portable Electronic Devices

NASA Technical Reports Server (NTRS)

Nguyen, Truong X.

2005-01-01

Cumulative interference effects from portable electronic devices (PEDs) located inside a passenger cabin are conservatively estimated for aircraft radio receivers. PEDs' emission powers in an aircraft radio frequency band are first scaled according to their locations' interference path loss (IPL) values, and the results are summed to determine the total interference power. The multiple-equipment-factor (MEF) is determined by normalizing the result against the worst case contribution from a single device. Conservative assumptions were made and MEF calculations were performed for Boeing 737's Localizer, Glide-slope, Traffic Collision Avoidance System, and Very High Frequency Communication radio systems where full-aircraft IPL data were available. The results show MEF for the systems to vary between 10 and 14 dB. The same process was also used on the more popular window/door IPL data, and the comparison show the multiple-equipment-factor results came within one decibel (dB) of each other.

Spinor helicity methods in high-energy factorization: Efficient momentum-space calculations in the Color Glass Condensate formalism

NASA Astrophysics Data System (ADS)

Ayala, Alejandro; Hentschinski, Martin; Jalilian-Marian, Jamal; Tejeda-Yeomans, Maria Elena

2017-07-01

We use the spinor helicity formalism to calculate the cross section for production of three partons of a given polarization in Deep Inelastic Scattering (DIS) off proton and nucleus targets at small Bjorken x. The target proton or nucleus is treated as a classical color field (shock wave) from which the produced partons scatter multiple times. We reported our result for the final expression for the production cross section and studied the azimuthal angular correlations of the produced partons in [1]. Here we provide the full details of the calculation of the production cross section using the spinor helicity methods.

[Co-author and keyword networks and their clustering appearance in preventive medicine fields in Korea: analysis of papers in the Journal of Preventive Medicine and Public Health, 1991~2006].

PubMed

Jung, Minsoo; Chung, Dongjun

2008-01-01

This study evaluated knowledge structure and its effect factor by analysis of co-author and keyword networks in Korea's preventive medicine sector. The data was extracted from 873 papers listed in the Journal of Preventive Medicine and Public Health, and was transformed into a co-author and keyword matrix where the existence of a 'link' was judged by impact factors calculated by the weight value of the role and rate of author participation. Research achievement was dependent upon the author's status and networking index, as analyzed by neighborhood degree, multidimensional scaling, correspondence analysis, and multiple regression. Co-author networks developed as randomness network in the center of a few high-productivity researchers. In particular, closeness centrality was more developed than degree centrality. Also, power law distribution was discovered in impact factor and research productivity by college affiliation. In multiple regression, the effect of the author's role was significant in both the impact factor calculated by the participatory rate and the number of listed articles. However, the number of listed articles varied by sex. This study shows that the small world phenomenon exists in co-author and keyword networks in a journal, as in citation networks. However, the differentiation of knowledge structure in the field of preventive medicine was relatively restricted by specialization.

Absolute measurements and certified reference material for iron isotopes using multiple-collector inductively coupled mass spectrometry.

PubMed

Zhou, Tao; Zhao, Motian; Wang, Jun; Lu, Hai

2008-01-01

Two enriched isotopes, 99.94 at.% 56Fe and 99.90 at.% 54Fe, were blended under gravimetric control to prepare ten synthetic isotope samples whose 56Fe isotope abundances ranged from 95% to 20%. For multiple-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) measurements typical polyatomic interferences were removed by using Ar and H2 as collision gas and operating the MC-ICP-MS system in soft mode. Thus high-precision measurements of the Fe isotope abundance ratios were accomplished. Based on the measurement of the synthetic isotope abundance ratios by MC-ICP-MS, the correction factor for mass discrimination was calculated and the results were in agreement with results from IRMM014. The precision of all ten correction factors was 0.044%, indicating a good linearity of the MC-ICP-MS method for different isotope abundance ratio values. An isotopic reference material was certified under the same conditions as the instrument was calibrated. The uncertainties of ten correction factors K were calculated and the final extended uncertainties of the isotopic certified Fe reference material were 5.8363(37) at.% 54Fe, 91.7621(51) at.% 56Fe, 2.1219(23) at.% 57Fe, and 0.2797(32) at.% 58Fe.

Comparative quantification of health risks: Conceptual framework and methodological issues

PubMed Central

Murray, Christopher JL; Ezzati, Majid; Lopez, Alan D; Rodgers, Anthony; Vander Hoorn, Stephen

2003-01-01

Reliable and comparable analysis of risks to health is key for preventing disease and injury. Causal attribution of morbidity and mortality to risk factors has traditionally been conducted in the context of methodological traditions of individual risk factors, often in a limited number of settings, restricting comparability. In this paper, we discuss the conceptual and methodological issues for quantifying the population health effects of individual or groups of risk factors in various levels of causality using knowledge from different scientific disciplines. The issues include: comparing the burden of disease due to the observed exposure distribution in a population with the burden from a hypothetical distribution or series of distributions, rather than a single reference level such as non-exposed; considering the multiple stages in the causal network of interactions among risk factor(s) and disease outcome to allow making inferences about some combinations of risk factors for which epidemiological studies have not been conducted, including the joint effects of multiple risk factors; calculating the health loss due to risk factor(s) as a time-indexed "stream" of disease burden due to a time-indexed "stream" of exposure, including consideration of discounting; and the sources of uncertainty. PMID:12780936

Suicidal ideation, risk factors, and communication with parents. An HBSC study on school children in Estonia, Lithuania, and Luxembourg.

PubMed

Mark, Lauraliisa; Samm, Algi; Tooding, Liina-Mai; Sisask, Merike; Aasvee, Katrin; Zaborskis, Apolinaras; Zemaitiene, Nida; Värnik, Airi

2013-01-01

Suicide is a leading cause of death among youth. In the year 2002, Lithuania had the 2nd, Luxembourg the 5th, and Estonia the 9th highest suicide rates among 15- to 19-year-olds across 90 countries worldwide. Suicidal ideation is a significant precursor to suicide. To report on the prevalence of and associations between suicidal ideation, smoking, alcohol consumption, physical fighting, bullying, and communication with parents among 15-year-old schoolchildren. The survey analyzes data from the 2005/2006 HBSC study from Estonia, Lithuania, and Luxembourg (N = 4,954). The risk factors were calculated through multinomial logistic regression analyses. The overall prevalence of suicidal ideation in the preceding year was 17%. Suicidal thoughts were associated with communication difficulties with parents (OR from 2.0 to 4.6) and other risk factors, especially multiple risks (OR for 4-5 concurrent risk factors from 4.5 to 13.6). Parent-child communication had a significant mediating effect by decreasing the odds for suicidality and multiple risks. The prevalence estimates were obtained by self-reports. The causal relationships need further investigation. The risk factors studied, particularly multiple risks, were associated with higher odds for suicidal ideation. Good parent-child communication is a significant resource for decreasing suicidal ideation among adolescents.

Dietary intakes assessed by 24-h recalls in peri-urban African adolescents: validity of energy intake compared with estimated energy expenditure.

PubMed

Rankin, D; Ellis, S M; Macintyre, U E; Hanekom, S M; Wright, H H

2011-08-01

The objective of this study is to determine the relative validity of reported energy intake (EI) derived from multiple 24-h recalls against estimated energy expenditure (EE(est)). Basal metabolic rate (BMR) equations and physical activity factors were incorporated to calculate EE(est). This analysis was nested in the multidisciplinary PhysicaL Activity in the Young study with a prospective study design. Peri-urban black South African adolescents were investigated in a subsample of 131 learners (87 girls and 44 boys) from the parent study sample of 369 (211 girls and 158 boys) who had all measurements taken. Pearson correlation coefficients and Bland-Altman plots were calculated to identify the most accurate published equations to estimate BMR (P<0.05 statistically significant). EE(est) was estimated using BMR equations and estimated physical activity factors derived from Previous Day Physical Activity Recall questionnaires. After calculation of EE(est), the relative validity of reported energy intake (EI(rep)) derived from multiple 24-h recalls was tested for three data subsets using Pearson correlation coefficients. Goldberg's formula identified cut points (CPs) for under and over reporting of EI. Pearson correlation coefficients between calculated BMRs ranged from 0.97 to 0.99. Bland-Altman analyses showed acceptable agreement (two equations for each gender). One equation for each gender was used to calculate EE(est). Pearson correlation coefficients between EI(rep) and EE(est) for three data sets were weak, indicating poor agreement. CPs for physical activity groups showed under reporting in 87% boys and 95% girls. The 24-h recalls measured at five measurements over 2 years offered poor validity between EI(rep) and EE(est).

Evaluating the relationship between wildfire extent and nitrogen dry deposition in a boreal forest in interior Alaska

NASA Astrophysics Data System (ADS)

Nagano, Hirohiko; Iwata, Hiroki

2017-03-01

Alaska wildfires may play an important role in nitrogen (N) dry deposition in Alaskan boreal forests. Here we used annual N dry deposition data measured by CASTNET at Denali National Park (DEN417) during 1999-2013, to evaluate the relationships between wildfire extent and N dry deposition in Alaska. We established six potential factors for multiple regression analysis, including burned area within 100 km of DEN417 (BA100km) and in other distant parts of Alaska (BAAK), the sum of indexes of North Atlantic Oscillation and Arctic Oscillation (OI), number of days with negative OI (OIday), precipitation (PRCP), and number of days with PRCP (PRCPday). Multiple regression analysis was conducted for both time scales, annual (using only annual values of factors) and six-month (using annual values of BAAK and BA100km, and fire and non-fire seasons' values of other four factors) time scales. Together, BAAK, BA100km, and OIday, along with PRCPday in the case of the six-month scale, explained more than 92% of the interannual variation in N dry deposition. The influence of BA100km on N dry deposition was ten-fold greater than from BAAK; the qualitative contribution was almost zero, however, due to the small BA100km. BAAK was the leading explanatory factor, with a 15 ± 14% contribution. We further calculated N dry deposition during 1950-2013 using the obtained regression equation and long-term records for the factors. The N dry deposition calculated for 1950-2013 revealed that an increased occurrence of wildfires during the 2000s led to the maximum N dry deposition exhibited during this decade. As a result, the effect of BAAK on N dry deposition remains sufficiently large, even when large possible uncertainties (>40%) in the measurement of N dry deposition are taken into account for the multiple regression analysis.

Risk factors of suicide mortality among multiple attempters: A national registry study in Taiwan.

PubMed

Chen, I-Ming; Liao, Shih-Cheng; Lee, Ming-Been; Wu, Chia-Yi; Lin, Po-Hsien; Chen, Wei J

2016-05-01

Little is known about the risk factors of suicide mortality among multiple attempters. This study aims to investigate the predictors of suicidal mortality in a prospective cohort of attempters in Taiwan, focusing on the time interval and suicide method change between the last two nonfatal attempts. The representative data retrieved from the National Suicide Surveillance System (NSSS) was linked with National Mortality Database to identify the causes of death in multiple attempters during 2006-2008. Cox-proportional hazard models were applied to calculate the hazard ratios for the predictors of suicide. Among the 55,560 attempters, 6485 (11.7%) had survived attempts ranging from one to 11 times; 861 (1.5%) eventually died by suicide. Multiple attempters were characterized by female (OR = 1.56, p < 0.0001), nonrecipient of national aftercare service (OR = 1.62, p < 0.0001), and current contact with mental health services (OR = 3.17, p < 0.0001). Most multiple attempters who survived from hanging (68.1%) and gas poisoning (61.9%) chose the same method in the following fatal episode. Predictors of suicidal death were identified as male, older age (≥ 45 years), shorter interval and not maintaining methods of low lethality in the last two nonfatal attempts. Receipt of nationwide aftercare was associated with lower risk of suicide but the effect was insignificant. The time interval of the last two nonfatal attempts and alteration in the lethality of suicide method were significant factors for completed suicide. Risk assessment involving these two factors may be necessary for multiple attempters in different clinical settings. Effective strategies for suicide prevention emphasizing this high risk population should be developed in the future. Copyright © 2015. Published by Elsevier B.V.

Multiple factors explain injury risk in adolescent elite athletes: Applying a biopsychosocial perspective.

PubMed

von Rosen, P; Frohm, A; Kottorp, A; Fridén, C; Heijne, A

2017-12-01

Many risk factors for injury are presented in the literature, few of those are however consistent and the majority is associated with adult and not adolescent elite athletes. The aim was to identify risk factors for injury in adolescent elite athletes, by applying a biopsychosocial approach. A total of 496 adolescent elite athletes (age range 15-19), participating in 16 different sports, were monitored repeatedly over 52 weeks using a valid questionnaire about injuries, training exposure, sleep, stress, nutrition, and competence-based self-esteem. Univariate and multiple Cox regression analyses were used to calculate hazard ratios (HR) for risk factors for first reported injury. The main finding was that an increase in training load, training intensity, and at the same time decreasing the sleep volume resulted in a higher risk for injury compared to no change in these variables (HR 2.25, 95% CI, 1.46-3.45, P<.01), which was the strongest risk factor identified. In addition, an increase by one score of competence-based self-esteem increased the hazard for injury with 1.02 (HR 95% CI, 1.00-1.04, P=.01). Based on the multiple Cox regression analysis, an athlete having the identified risk factors (Risk Index, competence-based self-esteem), with an average competence-based self-esteem score, had more than a threefold increased risk for injury (HR 3.35), compared to an athlete with a low competence-based self-esteem and no change in sleep or training volume. Our findings confirm injury occurrence as a result of multiple risk factors interacting in complex ways. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

The effect of multiplicity of stellar encounters and the diffusion coefficients in a locally homogeneous three-dimensional stellar medium: Removing the classical divergence

NASA Astrophysics Data System (ADS)

Rastorguev, A. S.; Utkin, N. D.; Chumak, O. V.

2017-08-01

Agekyan's λ-factor that allows for the effect of multiplicity of stellar encounters with large impact parameters has been used for the first time to directly calculate the diffusion coefficients in the phase space of a stellar system. Simple estimates show that the cumulative effect, i.e., the total contribution of distant encounters to the change in the velocity of a test star, given the multiplicity of stellar encounters, is finite, and the logarithmic divergence inherent in the classical description of diffusion is removed, as was shown previously byKandrup using a different, more complex approach. In this case, the expressions for the diffusion coefficients, as in the classical description, contain the logarithm of the ratio of two independent quantities: the mean interparticle distance and the impact parameter of a close encounter. However, the physical meaning of this logarithmic factor changes radically: it reflects not the divergence but the presence of two characteristic length scales inherent in the stellar medium.

Prediction of hearing outcomes by multiple regression analysis in patients with idiopathic sudden sensorineural hearing loss.

PubMed

Suzuki, Hideaki; Tabata, Takahisa; Koizumi, Hiroki; Hohchi, Nobusuke; Takeuchi, Shoko; Kitamura, Takuro; Fujino, Yoshihisa; Ohbuchi, Toyoaki

2014-12-01

This study aimed to create a multiple regression model for predicting hearing outcomes of idiopathic sudden sensorineural hearing loss (ISSNHL). The participants were 205 consecutive patients (205 ears) with ISSNHL (hearing level ≥ 40 dB, interval between onset and treatment ≤ 30 days). They received systemic steroid administration combined with intratympanic steroid injection. Data were examined by simple and multiple regression analyses. Three hearing indices (percentage hearing improvement, hearing gain, and posttreatment hearing level [HLpost]) and 7 prognostic factors (age, days from onset to treatment, initial hearing level, initial hearing level at low frequencies, initial hearing level at high frequencies, presence of vertigo, and contralateral hearing level) were included in the multiple regression analysis as dependent and explanatory variables, respectively. In the simple regression analysis, the percentage hearing improvement, hearing gain, and HLpost showed significant correlation with 2, 5, and 6 of the 7 prognostic factors, respectively. The multiple correlation coefficients were 0.396, 0.503, and 0.714 for the percentage hearing improvement, hearing gain, and HLpost, respectively. Predicted values of HLpost calculated by the multiple regression equation were reliable with 70% probability with a 40-dB-width prediction interval. Prediction of HLpost by the multiple regression model may be useful to estimate the hearing prognosis of ISSNHL. © The Author(s) 2014.

Estimates of live-tree carbon stores in the Pacific Northwest are sensitive to model selection

Treesearch

Susanna L. Melson; Mark E. Harmon; Jeremy S. Fried; James B. Domingo

2011-01-01

Estimates of live-tree carbon stores are influenced by numerous uncertainties. One of them is model-selection uncertainty: one has to choose among multiple empirical equations and conversion factors that can be plausibly justified as locally applicable to calculate the carbon store from inventory measurements such as tree height and diameter at breast height (DBH)....

In search of real autonomy for fertility patients.

PubMed

Johnston, Josephine; Gusmano, Michael K; Patrizio, Pasquale

2015-07-01

Nearly one in eight infants in the United States is born preterm. A variety of factors are associated with preterm birth, including multiplicity. In the United States fertility treatments are currently associated with high rates of multiplicity, but these rates could be reduced significantly if changes can be made to fertility treatment policy and practice. These include reducing the financial pressure on patients to prioritize pregnancy chances over safety by expanding insurance coverage and altering the way we calculate success rates and insurance benefits so that two consecutive single embryo transfers is equivalent to one double embryo transfer.

Calculation and application of energy transaction allocation factors in electric power transmission systems

NASA Astrophysics Data System (ADS)

Fradi, Aniss

The ability to allocate the active power (MW) loading on transmission lines and transformers, is the basis of the "flow based" transmission allocation system developed by the North American Electric Reliability Council. In such a system, the active power flows must be allocated to each line or transformer in proportion to the active power being transmitted by each transaction imposed on the system. Currently, this is accomplished through the use of the linear Power Transfer Distribution Factors (PTDFs). Unfortunately, no linear allocation models exist for other energy transmission quantities, such as MW and MVAR losses, MVAR and MVA flows, etc. Early allocation schemes were developed to allocate MW losses due to transactions to branches in a transmission system, however they exhibited diminished accuracy, since most of them are based on linear power flow modeling of the transmission system. This thesis presents a new methodology to calculate Energy Transaction Allocation factors (ETA factors, or eta factors), using the well-known process of integration of a first derivative function, as well as consistent and well-established mathematical and AC power flow models. The factors give a highly accurate allocation of any non-linear system quantity to transactions placed on the transmission system. The thesis also extends the new ETA factors calculation procedure to restructure a new economic dispatch scheme where multiple sets of generators are economically dispatched to meet their corresponding load and their share of the losses.

Persian adaptation of a questionnaire of environmental risk factors in multiple sclerosis (EnvIMS-Q).

PubMed

Sahraian, Mohammad Ali; Naghshineh, Hoda; Shati, Mohsen; Jahromi, Soodeh Razeghi; Rezaei, Niloofar

2016-11-01

It seems that gene-environment interaction play most important role in Multiple Sclerosis development. Increasing the incidence and prevalence of MS during the recent decades in the low prevalence area such as Iran is explained better by environment factors. Environmental Risk Factors in Multiple Sclerosis (the 'EnvIMS-Q') is a 6-page self-administered questionnaire for case control studies. the objectives of study are validation and adaptation of the EnvIMS-Q' then development of a Persian version for case control studies in Persian population. This questionnaire translated literally and in culturally relevant form, then content validation process was done by three groups' experts. According to giving rating to each item, each section and the whole instrument, we calculated their content validation indexes and also added some new questions and a new section to EnvIMS-Q. Finally, we analyzed repeatability of the answers within a 4 weeks interval. Relevancy and clarity indexes of all items were more than 80%. Scale relevancy index equaled 99% and scale clarity index equaled 97%. Repeatability of most items was acceptable. the use of standardized validated questionnaires will assist the researchers to perform local studies on the role of environmental factors on the basis of reliable data. Copyright © 2016 Elsevier B.V. All rights reserved.

GRAY: a program to calculate gray-body radiation heat-transfer view factors from black-body view factors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wong, R. L.

1976-06-14

Program GRAY is written to perform the matrix manipulations necessary to convert black-body radiation heat-transfer view factors to gray-body view factors as required by thermal analyzer codes. The black-body view factors contain only geometric relationships. Program GRAY allows the effects of multiple gray-body reflections to be included. The resulting effective gray-body factors can then be used with the corresponding fourth-power temperature differences to obtain the net radiative heat flux. The program is written to accept a matrix input or the card image output generated by the black-body view factor program CNVUFAC. The resulting card image output generated by GRAY ismore » in a form usable by the TRUMP thermal analyzer.« less

Spatial evolution of laser filaments in turbulent air

NASA Astrophysics Data System (ADS)

Zeng, Tao; Zhu, Shiping; Zhou, Shengling; He, Yan

2018-04-01

In this study, the spatial evolution properties of laser filament clusters in turbulent air were evaluated using numerical simulations. Various statistical parameters were calculated, such as the percolation probability, filling factor, and average cluster size. The results indicate that turbulence-induced multi-filamentation can be described as a new phase transition universality class. In addition, during this process, the relationship between the average cluster size and filling factor could be fit by a power function. Our results are valuable for applications involving filamentation that can be influenced by the geometrical features of multiple filaments.

Simulation of land use change in the three gorges reservoir area based on CART-CA

NASA Astrophysics Data System (ADS)

Yuan, Min

2018-05-01

This study proposes a new method to simulate spatiotemporal complex multiple land uses by using classification and regression tree algorithm (CART) based CA model. In this model, we use classification and regression tree algorithm to calculate land class conversion probability, and combine neighborhood factor, random factor to extract cellular transformation rules. The overall Kappa coefficient is 0.8014 and the overall accuracy is 0.8821 in the land dynamic simulation results of the three gorges reservoir area from 2000 to 2010, and the simulation results are satisfactory.

[Why do mothers smoke? Analyzing the influence of living circumstances and psychological factors on tobacco consumption among mothers with minor children].

PubMed

Sperlich, S; Illiger, K; Geyer, S

2011-11-01

Using a cross-sectional population sample of 3,129 women with minor children, this paper analyzes the impact of social and psychological factors on maternal smoking. Pearson's χ(2) was used for testing significance of differences between smoking prevalence and social as well as psychological factors. Adjusted effects of these factors were calculated by means of multiple logistic regression analysis. About 30% of mothers smoked daily and about 11% were heavy smokers ( ≥ 20 cigarettes/day). Lower educational degree was the most important predictor for daily tobacco consumption. But also fulltime employment, low income, distress due to conflicts with (former) partner, job-related burdens, and single motherhood enhanced the risk of maternal smoking, while household-related stress and having a young child was associated with less tobacco use. With respect to personal factors, dysfunctional coping patterns and depression showed a significant impact on tobacco use. Against expectations, active coping styles were not associated with lower but with increased smoking rates. In conclusion, it can be stated that maternal smoking has multiple causes, and that intervention programs should target both current living circumstances and psychological factors.

A factor analytic investigation of the Mercy Evaluation of Multiple Sclerosis.

PubMed

Merz, Zachary C; Wright, John D; Vander Wal, Jillon S; Gfeller, Jeffrey D

2018-01-23

Neurocognitive deficits commonly are an accompanying feature of Multiple Sclerosis (MS). A brief, yet comprehensive neuropsychological battery is desirable for assessing the extent of these deficits. Therefore, the present study examined the validity of the Mercy Evaluation of Multiple Sclerosis (MEMS) for use with the MS population. Archival data from individuals diagnosed with MS (N = 378) by independent neurologists was examined. Cognitive domains assessed included processing speed and attention, learning, and memory, visuospatial, language, and executive functioning. A mean battery index was calculated to provide a general indicator of cognitive impairment within the current sample. Overall performance across participants was found to be in the lower limits of the average range. Results of factor analytic statistical procedures yielded a four-factor solution, accounting for 67% of total variance within the MEMS. Four neurocognitive measures exhibited the highest sensitivity in detecting cognitive impairment, constituting a psychometrically established brief cognitive screening battery, which accounted for 83% of total variance within the mean battery index score. Overall, the results of the current study suggest appropriate construct validity of the MEMS for use with individuals with MS, as well as provide support for previously established cognitive batteries.

Analyzing the thermionic reactor critical experiments. [thermal spectrum of uranium 235 core

NASA Technical Reports Server (NTRS)

Niederauer, G. F.

1973-01-01

The Thermionic Reactor Critical Experiments (TRCE) consisted of fast spectrum highly enriched U-235 cores reflected by different thicknesses of beryllium or beryllium oxide with a transition zone of stainless steel between the core and reflector. The mixed fast-thermal spectrum at the core reflector interface region poses a difficult neutron transport calculation. Calculations of TRCE using ENDF/B fast spectrum data and GATHER library thermal spectrum data agreed within about 1 percent for the multiplication factor and within 6 to 8 percent for the power peaks. Use of GAM library fast spectrum data yielded larger deviations. The results were obtained from DOT R Theta calculations with leakage cross sections, by region and by group, extracted from DOT RZ calculations. Delineation of the power peaks required extraordinarily fine mesh size at the core reflector interface.

Fuel burnup analysis for IRIS reactor using MCNPX and WIMS-D5 codes

NASA Astrophysics Data System (ADS)

Amin, E. A.; Bashter, I. I.; Hassan, Nabil M.; Mustafa, S. S.

2017-02-01

International Reactor Innovative and Secure (IRIS) reactor is a compact power reactor designed with especial features. It contains Integral Fuel Burnable Absorber (IFBA). The core is heterogeneous both axially and radially. This work provides the full core burn up analysis for IRIS reactor using MCNPX and WIMDS-D5 codes. Criticality calculations, radial and axial power distributions and nuclear peaking factor at the different stages of burnup were studied. Effective multiplication factor values for the core were estimated by coupling MCNPX code with WIMS-D5 code and compared with SAS2H/KENO-V code values at different stages of burnup. The two calculation codes show good agreement and correlation. The values of radial and axial powers for the full core were also compared with published results given by SAS2H/KENO-V code (at the beginning and end of reactor operation). The behavior of both radial and axial power distribution is quiet similar to the other data published by SAS2H/KENO-V code. The peaking factor values estimated in the present work are close to its values calculated by SAS2H/KENO-V code.

Assessing Risk Prediction Models Using Individual Participant Data From Multiple Studies

PubMed Central

Pennells, Lisa; Kaptoge, Stephen; White, Ian R.; Thompson, Simon G.; Wood, Angela M.; Tipping, Robert W.; Folsom, Aaron R.; Couper, David J.; Ballantyne, Christie M.; Coresh, Josef; Goya Wannamethee, S.; Morris, Richard W.; Kiechl, Stefan; Willeit, Johann; Willeit, Peter; Schett, Georg; Ebrahim, Shah; Lawlor, Debbie A.; Yarnell, John W.; Gallacher, John; Cushman, Mary; Psaty, Bruce M.; Tracy, Russ; Tybjærg-Hansen, Anne; Price, Jackie F.; Lee, Amanda J.; McLachlan, Stela; Khaw, Kay-Tee; Wareham, Nicholas J.; Brenner, Hermann; Schöttker, Ben; Müller, Heiko; Jansson, Jan-Håkan; Wennberg, Patrik; Salomaa, Veikko; Harald, Kennet; Jousilahti, Pekka; Vartiainen, Erkki; Woodward, Mark; D'Agostino, Ralph B.; Bladbjerg, Else-Marie; Jørgensen, Torben; Kiyohara, Yutaka; Arima, Hisatomi; Doi, Yasufumi; Ninomiya, Toshiharu; Dekker, Jacqueline M.; Nijpels, Giel; Stehouwer, Coen D. A.; Kauhanen, Jussi; Salonen, Jukka T.; Meade, Tom W.; Cooper, Jackie A.; Cushman, Mary; Folsom, Aaron R.; Psaty, Bruce M.; Shea, Steven; Döring, Angela; Kuller, Lewis H.; Grandits, Greg; Gillum, Richard F.; Mussolino, Michael; Rimm, Eric B.; Hankinson, Sue E.; Manson, JoAnn E.; Pai, Jennifer K.; Kirkland, Susan; Shaffer, Jonathan A.; Shimbo, Daichi; Bakker, Stephan J. L.; Gansevoort, Ron T.; Hillege, Hans L.; Amouyel, Philippe; Arveiler, Dominique; Evans, Alun; Ferrières, Jean; Sattar, Naveed; Westendorp, Rudi G.; Buckley, Brendan M.; Cantin, Bernard; Lamarche, Benoît; Barrett-Connor, Elizabeth; Wingard, Deborah L.; Bettencourt, Richele; Gudnason, Vilmundur; Aspelund, Thor; Sigurdsson, Gunnar; Thorsson, Bolli; Kavousi, Maryam; Witteman, Jacqueline C.; Hofman, Albert; Franco, Oscar H.; Howard, Barbara V.; Zhang, Ying; Best, Lyle; Umans, Jason G.; Onat, Altan; Sundström, Johan; Michael Gaziano, J.; Stampfer, Meir; Ridker, Paul M.; Michael Gaziano, J.; Ridker, Paul M.; Marmot, Michael; Clarke, Robert; Collins, Rory; Fletcher, Astrid; Brunner, Eric; Shipley, Martin; Kivimäki, Mika; Ridker, Paul M.; Buring, Julie; Cook, Nancy; Ford, Ian; Shepherd, James; Cobbe, Stuart M.; Robertson, Michele; Walker, Matthew; Watson, Sarah; Alexander, Myriam; Butterworth, Adam S.; Angelantonio, Emanuele Di; Gao, Pei; Haycock, Philip; Kaptoge, Stephen; Pennells, Lisa; Thompson, Simon G.; Walker, Matthew; Watson, Sarah; White, Ian R.; Wood, Angela M.; Wormser, David; Danesh, John

2014-01-01

Individual participant time-to-event data from multiple prospective epidemiologic studies enable detailed investigation into the predictive ability of risk models. Here we address the challenges in appropriately combining such information across studies. Methods are exemplified by analyses of log C-reactive protein and conventional risk factors for coronary heart disease in the Emerging Risk Factors Collaboration, a collation of individual data from multiple prospective studies with an average follow-up duration of 9.8 years (dates varied). We derive risk prediction models using Cox proportional hazards regression analysis stratified by study and obtain estimates of risk discrimination, Harrell's concordance index, and Royston's discrimination measure within each study; we then combine the estimates across studies using a weighted meta-analysis. Various weighting approaches are compared and lead us to recommend using the number of events in each study. We also discuss the calculation of measures of reclassification for multiple studies. We further show that comparison of differences in predictive ability across subgroups should be based only on within-study information and that combining measures of risk discrimination from case-control studies and prospective studies is problematic. The concordance index and discrimination measure gave qualitatively similar results throughout. While the concordance index was very heterogeneous between studies, principally because of differing age ranges, the increments in the concordance index from adding log C-reactive protein to conventional risk factors were more homogeneous. PMID:24366051

Assessing risk prediction models using individual participant data from multiple studies.

PubMed

Pennells, Lisa; Kaptoge, Stephen; White, Ian R; Thompson, Simon G; Wood, Angela M

2014-03-01

Individual participant time-to-event data from multiple prospective epidemiologic studies enable detailed investigation into the predictive ability of risk models. Here we address the challenges in appropriately combining such information across studies. Methods are exemplified by analyses of log C-reactive protein and conventional risk factors for coronary heart disease in the Emerging Risk Factors Collaboration, a collation of individual data from multiple prospective studies with an average follow-up duration of 9.8 years (dates varied). We derive risk prediction models using Cox proportional hazards regression analysis stratified by study and obtain estimates of risk discrimination, Harrell's concordance index, and Royston's discrimination measure within each study; we then combine the estimates across studies using a weighted meta-analysis. Various weighting approaches are compared and lead us to recommend using the number of events in each study. We also discuss the calculation of measures of reclassification for multiple studies. We further show that comparison of differences in predictive ability across subgroups should be based only on within-study information and that combining measures of risk discrimination from case-control studies and prospective studies is problematic. The concordance index and discrimination measure gave qualitatively similar results throughout. While the concordance index was very heterogeneous between studies, principally because of differing age ranges, the increments in the concordance index from adding log C-reactive protein to conventional risk factors were more homogeneous.

Prevalence of bacterial vaginosis among pregnant women attending antenatal care in Tikur Anbessa University Hospital, Addis Ababa, Ethiopia.

PubMed

Mengistie, Zemenu; Woldeamanuel, Yimtubezinash; Asrat, Daniel; Adera, Addis

2014-11-20

Bacterial vaginosis is one of the most common genital tract infections among reproductive age group. The prevalence of bacterial vaginosis varies from country to country even in the same country it varies among populations of interest. Different social and sexual factors can contribute to the development of bacterial vaginosis. The aim of this study was to determine the prevalence of bacterial vaginosis and to identify the possible risk factors associated among pregnant women attending antenatal care in Tikur Anbessa University Hospital, Addis Ababa, Ethiopia. Randomly selected 57 symptomatic and 195 asymptomatic pregnant women aged between 18 and 40 years visiting obstetric and gynecological clinic from November 2011 to April 2012 screenedusing Gram stain Nugent scoring system. Statistical analysis like univariate analysis to calculate frequencies and proportions, bivariate analysis to see association of selected exposure variables with the outcome variable, and multivariate analysis to check the association of possible factors with bacterial vaginosis by adjusting potential confounding factors was calculated using SPSS (Version 16.0). The prevalence of bacterial vaginosis is 19.4% using Gram stain Nugent scoring system. In addition, prevalence of bacterial vaginosis is 31.6% and 15.9% among symptomatic and asymptomatic pregnant women respectively. A high percentage of bacterial vaginosis positive pregnant women were asymptomatic (63.3%). 36.7% bacterial vaginosis positive pregnant women reported abnormal vaginal discharge with or without unpleasant smell. Multiple lifetime sexual partner (OR: 8.6; 95% CI: 2.5, 29) and previous history of spontaneous abortion (OR: 5.9; 95% CI: 1.5, 23) had remained significantly associated with prevalence of bacterial vaginosis. The prevalence of bacterial vaginosis is higher among asymptomatic pregnant women and associated with the factors previous history of multiple lifetime sexual partner and spontaneous abortion.

An elastic strip with multiple cracks and applications to tapered specimens

NASA Technical Reports Server (NTRS)

Liu, X.-H.; Erdogan, F.

1985-01-01

In this paper an infinite elastic strip containing arbitrarily oriented cracks and subjected to uniform tension and a pair of concentrated forces is formulated in terms of a system of singular integral equations. Even though the technique is sufficiently general to solve new multiple crack problem, with the objective of applying the results to tapered specimens, only a certain symmetric crack geometry and loading conditions are considered. The stress intensity factors are calculated for edge cracks in the strip under uniform tension and for a 'compact' and a 'slender' tapered specimen (the latter simulating the double cantilever beam) under concentrated forces or crack surface wedge forces.

SU-F-T-157: Physics Considerations Regarding Dosimetric Accuracy of Analytical Dose Calculations for Small Field Proton Therapy: A Monte Carlo Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geng, C; Nanjing University of Aeronautics and Astronautics, Nanjing; Daartz, J

Purpose: To evaluate the accuracy of dose calculations by analytical dose calculation methods (ADC) for small field proton therapy in a gantry based passive scattering facility. Methods: 50 patients with intra-cranial disease were evaluated in the study. Treatment plans followed standard prescription and optimization procedures of proton stereotactic radiosurgery. Dose distributions calculated with the Monte Carlo (MC) toolkit TOPAS were used to represent delivered treatments. The MC dose was first adjusted using the output factor (OF) applied clinically. This factor is determined from the field size and the prescribed range. We then introduced a normalization factor to measure the differencemore » in mean dose between the delivered dose (MC dose with OF) and the dose calculated by ADC for each beam. The normalization was determined by the mean dose of the center voxels of the target area. We compared delivered dose distributions and those calculated by ADC in terms of dose volume histogram parameters and beam range distributions. Results: The mean target dose for a whole treatment is generally within 5% comparing delivered dose (MC dose with OF) and ADC dose. However, the differences can be as great as 11% for shallow and small target treated with a thick range compensator. Applying the normalization factor to the MC dose with OF can reduce the mean dose difference to less than 3%. Considering range uncertainties, the generally applied margins (3.5% of the prescribed range + 1mm) to cover uncertainties in range might not be sufficient to guarantee tumor coverage. The range difference for R90 (90% distal dose falloff) is affected by multiple factors, such as the heterogeneity index. Conclusion: This study indicates insufficient accuracy calculating proton doses using ADC. Our results suggest that uncertainties of target doses are reduced using MC techniques, improving the dosimetric accuracy for proton stereotactic radiosurgery. The work was supported by NIH/NCI under CA U19 021239. CG was partially supported by the Chinese Scholarship Council (CSC) and the National Natural Science Foundation of China (Grant No. 11475087).« less

Expanded uncertainty associated with determination of isotope enrichment factors: Comparison of two point calculation and Rayleigh-plot.

PubMed

Julien, Maxime; Gilbert, Alexis; Yamada, Keita; Robins, Richard J; Höhener, Patrick; Yoshida, Naohiro; Remaud, Gérald S

2018-01-01

The enrichment factor (ε) is a common way to express Isotope Effects (IEs) associated with a phenomenon. Many studies determine ε using a Rayleigh-plot, which needs multiple data points. More recent articles describe an alternative method using the Rayleigh equation that allows the determination of ε using only one experimental point, but this method is often subject to controversy. However, a calculation method using two points (one experimental point and one at t 0 ) should lead to the same results because the calculation is derived from the Rayleigh equation. But, it is frequently asked "what is the valid domain of use of this two point calculation?" The primary aim of the present work is a systematic comparison of results obtained with these two methodologies and the determination of the conditions required for the valid calculation of ε. In order to evaluate the efficiency of the two approaches, the expanded uncertainty (U) associated with determining ε has been calculated using experimental data from three published articles. The second objective of the present work is to describe how to determine the expanded uncertainty (U) associated with determining ε. Comparative methodologies using both Rayleigh-plot and two point calculation are detailed and it is clearly demonstrated that calculation of ε using a single data point can give the same result as a Rayleigh-plot provided one strict condition is respected: that the experimental value is measured at a small fraction of unreacted substrate (f < 30%). This study will help stable isotope users to present their results in a more rigorous expression: ε ± U and therefore to define better the significance of an experimental results prior interpretation. Capsule: Enrichment factor can be determined through two different methods and the calculation of associated expanded uncertainty allows checking its significance. Copyright © 2017 Elsevier B.V. All rights reserved.

Pressure Ratio to Thermal Environments

NASA Technical Reports Server (NTRS)

Lopez, Pedro; Wang, Winston

2012-01-01

A pressure ratio to thermal environments (PRatTlE.pl) program is a Perl language code that estimates heating at requested body point locations by scaling the heating at a reference location times a pressure ratio factor. The pressure ratio factor is the ratio of the local pressure at the reference point and the requested point from CFD (computational fluid dynamics) solutions. This innovation provides pressure ratio-based thermal environments in an automated and traceable method. Previously, the pressure ratio methodology was implemented via a Microsoft Excel spreadsheet and macro scripts. PRatTlE is able to calculate heating environments for 150 body points in less than two minutes. PRatTlE is coded in Perl programming language, is command-line-driven, and has been successfully executed on both the HP and Linux platforms. It supports multiple concurrent runs. PRatTlE contains error trapping and input file format verification, which allows clear visibility into the input data structure and intermediate calculations.

An iterative method for obtaining the optimum lightning location on a spherical surface

NASA Technical Reports Server (NTRS)

Chao, Gao; Qiming, MA

1991-01-01

A brief introduction to the basic principles of an eigen method used to obtain the optimum source location of lightning is presented. The location of the optimum source is obtained by using multiple direction finders (DF's) on a spherical surface. An improvement of this method, which takes the distance of source-DF's as a constant, is presented. It is pointed out that using a weight factor of signal strength is not the most ideal method because of the inexact inverse signal strength-distance relation and the inaccurate signal amplitude. An iterative calculation method is presented using the distance from the source to the DF as a weight factor. This improved method has higher accuracy and needs only a little more calculation time. Some computer simulations for a 4DF system are presented to show the improvement of location through use of the iterative method.

Epidemiologic programs for computers and calculators. A microcomputer program for multiple logistic regression by unconditional and conditional maximum likelihood methods.

PubMed

Campos-Filho, N; Franco, E L

1989-02-01

A frequent procedure in matched case-control studies is to report results from the multivariate unmatched analyses if they do not differ substantially from the ones obtained after conditioning on the matching variables. Although conceptually simple, this rule requires that an extensive series of logistic regression models be evaluated by both the conditional and unconditional maximum likelihood methods. Most computer programs for logistic regression employ only one maximum likelihood method, which requires that the analyses be performed in separate steps. This paper describes a Pascal microcomputer (IBM PC) program that performs multiple logistic regression by both maximum likelihood estimation methods, which obviates the need for switching between programs to obtain relative risk estimates from both matched and unmatched analyses. The program calculates most standard statistics and allows factoring of categorical or continuous variables by two distinct methods of contrast. A built-in, descriptive statistics option allows the user to inspect the distribution of cases and controls across categories of any given variable.

Do climate variables and human density affect Achatina fulica (Bowditch) (Gastropoda: Pulmonata) shell length, total weight and condition factor?

PubMed

Albuquerque, F S; Peso-Aguiar, M C; Assunção-Albuquerque, M J T; Gálvez, L

2009-08-01

The length-weight relationship and condition factor have been broadly investigated in snails to obtain the index of physical condition of populations and evaluate habitat quality. Herein, our goal was to describe the best predictors that explain Achatina fulica biometrical parameters and well being in a recently introduced population. From November 2001 to November 2002, monthly snail samples were collected in Lauro de Freitas City, Bahia, Brazil. Shell length and total weight were measured in the laboratory and the potential curve and condition factor were calculated. Five environmental variables were considered: temperature range, mean temperature, humidity, precipitation and human density. Multiple regressions were used to generate models including multiple predictors, via model selection approach, and then ranked with AIC criteria. Partial regressions were used to obtain the separated coefficients of determination of climate and human density models. A total of 1.460 individuals were collected, presenting a shell length range between 4.8 to 102.5 mm (mean: 42.18 mm). The relationship between total length and total weight revealed that Achatina fulica presented a negative allometric growth. Simple regression indicated that humidity has a significant influence on A. fulica total length and weight. Temperature range was the main variable that influenced the condition factor. Multiple regressions showed that climatic and human variables explain a small proportion of the variance in shell length and total weight, but may explain up to 55.7% of the condition factor variance. Consequently, we believe that the well being and biometric parameters of A. fulica can be influenced by climatic and human density factors.

A rough set-based measurement model study on high-speed railway safety operation.

PubMed

Hu, Qizhou; Tan, Minjia; Lu, Huapu; Zhu, Yun

2018-01-01

Aiming to solve the safety problems of high-speed railway operation and management, one new method is urgently needed to construct on the basis of the rough set theory and the uncertainty measurement theory. The method should carefully consider every factor of high-speed railway operation that realizes the measurement indexes of its safety operation. After analyzing the factors that influence high-speed railway safety operation in detail, a rough measurement model is finally constructed to describe the operation process. Based on the above considerations, this paper redistricts the safety influence factors of high-speed railway operation as 16 measurement indexes which include staff index, vehicle index, equipment index and environment. And the paper also provides another reasonable and effective theoretical method to solve the safety problems of multiple attribute measurement in high-speed railway operation. As while as analyzing the operation data of 10 pivotal railway lines in China, this paper respectively uses the rough set-based measurement model and value function model (one model for calculating the safety value) for calculating the operation safety value. The calculation result shows that the curve of safety value with the proposed method has smaller error and greater stability than the value function method's, which verifies the feasibility and effectiveness.

The Radiological Physics Center's standard dataset for small field size output factors.

PubMed

Followill, David S; Kry, Stephen F; Qin, Lihong; Lowenstein, Jessica; Molineu, Andrea; Alvarez, Paola; Aguirre, Jose Francisco; Ibbott, Geoffrey S

2012-08-08

Delivery of accurate intensity-modulated radiation therapy (IMRT) or stereotactic radiotherapy depends on a multitude of steps in the treatment delivery process. These steps range from imaging of the patient to dose calculation to machine delivery of the treatment plan. Within the treatment planning system's (TPS) dose calculation algorithm, various unique small field dosimetry parameters are essential, such as multileaf collimator modeling and field size dependence of the output. One of the largest challenges in this process is determining accurate small field size output factors. The Radiological Physics Center (RPC), as part of its mission to ensure that institutions deliver comparable and consistent radiation doses to their patients, conducts on-site dosimetry review visits to institutions. As a part of the on-site audit, the RPC measures the small field size output factors as might be used in IMRT treatments, and compares the resulting field size dependent output factors to values calculated by the institution's treatment planning system (TPS). The RPC has gathered multiple small field size output factor datasets for X-ray energies ranging from 6 to 18 MV from Varian, Siemens and Elekta linear accelerators. These datasets were measured at 10 cm depth and ranged from 10 × 10 cm(2) to 2 × 2 cm(2). The field sizes were defined by the MLC and for the Varian machines the secondary jaws were maintained at a 10 × 10 cm(2). The RPC measurements were made with a micro-ion chamber whose volume was small enough to gather a full ionization reading even for the 2 × 2 cm(2) field size. The RPC-measured output factors are tabulated and are reproducible with standard deviations (SD) ranging from 0.1% to 1.5%, while the institutions' calculated values had a much larger SD range, ranging up to 7.9% [corrected].The absolute average percent differences were greater for the 2 × 2 cm(2) than for the other field sizes. The RPC's measured small field output factors provide institutions with a standard dataset against which to compare their TPS calculated values. Any discrepancies noted between the standard dataset and calculated values should be investigated with careful measurements and with attention to the specific beam model.

HIV dynamics with multiple infections of target cells.

PubMed

Dixit, Narendra M; Perelson, Alan S

2005-06-07

The high incidence of multiple infections of cells by HIV sets the stage for rapid HIV evolution by means of recombination. Yet how HIV dynamics proceeds with multiple infections remains poorly understood. Here, we present a mathematical model that describes the dynamics of viral, target cell, and multiply infected cell subpopulations during HIV infection. Model calculations reproduce several experimental observations and provide key insights into the influence of multiple infections on HIV dynamics. We find that the experimentally observed scaling law, that the number of cells coinfected with two distinctly labeled viruses is proportional to the square of the total number of infected cells, can be generalized so that the number of triply infected cells is proportional to the cube of the number of infected cells, etc. Despite the expectation from Poisson statistics, we find that this scaling relationship only holds under certain conditions, which we predict. We also find that multiple infections do not influence viral dynamics when the rate of viral production from infected cells is independent of the number of times the cells are infected, a regime expected when viral production is limited by cellular rather than viral factors. This result may explain why extant models, which ignore multiple infections, successfully describe viral dynamics in HIV patients. Inhibiting CD4 down-modulation increases the average number of infections per cell. Consequently, altering CD4 down-modulation may allow for an experimental determination of whether viral or cellular factors limit viral production.

HIV dynamics with multiple infections of target cells

PubMed Central

Dixit, Narendra M.; Perelson, Alan S.

2005-01-01

The high incidence of multiple infections of cells by HIV sets the stage for rapid HIV evolution by means of recombination. Yet how HIV dynamics proceeds with multiple infections remains poorly understood. Here, we present a mathematical model that describes the dynamics of viral, target cell, and multiply infected cell subpopulations during HIV infection. Model calculations reproduce several experimental observations and provide key insights into the influence of multiple infections on HIV dynamics. We find that the experimentally observed scaling law, that the number of cells coinfected with two distinctly labeled viruses is proportional to the square of the total number of infected cells, can be generalized so that the number of triply infected cells is proportional to the cube of the number of infected cells, etc. Despite the expectation from Poisson statistics, we find that this scaling relationship only holds under certain conditions, which we predict. We also find that multiple infections do not influence viral dynamics when the rate of viral production from infected cells is independent of the number of times the cells are infected, a regime expected when viral production is limited by cellular rather than viral factors. This result may explain why extant models, which ignore multiple infections, successfully describe viral dynamics in HIV patients. Inhibiting CD4 down-modulation increases the average number of infections per cell. Consequently, altering CD4 down-modulation may allow for an experimental determination of whether viral or cellular factors limit viral production. PMID:15928092

CLASH: THE ENHANCED LENSING EFFICIENCY OF THE HIGHLY ELONGATED MERGING CLUSTER MACS J0416.1-2403

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zitrin, A.; Bartelmann, M.; Carrasco, M.

2013-01-10

We perform a strong lensing analysis of the merging galaxy cluster MACS J0416.1-2403 (M0416; z = 0.42) in recent CLASH/HST observations. We identify 70 new multiple images and candidates of 23 background sources in the range 0.7 {approx}< z{sub phot} {approx}< 6.14 including two probable high-redshift dropouts, revealing a highly elongated lens with axis ratio {approx_equal}5:1, and a major axis of {approx}100'' (z{sub s} {approx} 2). Compared to other well-studied clusters, M0416 shows an enhanced lensing efficiency. Although the critical area is not particularly large ({approx_equal} 0.6 {open_square}'; z{sub s} {approx} 2), the number of multiple images, per critical area,more » is anomalously high. We calculate that the observed elongation boosts the number of multiple images, per critical area, by a factor of {approx}2.5 Multiplication-Sign , due to the increased ratio of the caustic area relative to the critical area. Additionally, we find that the observed separation between the two main mass components enlarges the critical area by a factor of {approx}2. These geometrical effects can account for the high number (density) of multiple images observed. We find in numerical simulations that only {approx}4% of the clusters (with M{sub vir} {>=} 6 Multiplication-Sign 10{sup 14} h {sup -1} M{sub Sun }) exhibit critical curves as elongated as in M0416.« less

Morphological characteristics associated with rupture risk of multiple intracranial aneurysms.

PubMed

Wang, Guang-Xian; Liu, Lan-Lan; Wen, Li; Cao, Yun-Xing; Pei, Yu-Chun; Zhang, Dong

2017-10-01

To identify the morphological parameters that are related to intracranial aneurysms (IAs) rupture using a case-control model. A total of 107 patients with multiple IAs and aneurysmal subarachnoid hemorrhage between August 2011 and February 2017 were enrolled in this study. Characteristics of IAs location, shape, neck width, perpendicular height, depth, maximum size, flow angle, parent vessel diameter (PVD), aspect ratio (AR) and size ratio (SR) were evaluated using CT angiography. Multiple logistic regression analysis was used to identify the independent risk factors associated with IAs rupture. Receiver operating characteristic curve analysis was performed on the final model, and the optimal thresholds were obtained. IAs located in the internal carotid artery (ICA) was associated with a negative risk of rupture, whereas AR, SR1 (height/PVD) and SR2 (depth/PVD) were associated with increased risk of rupture. When SR was calculated differently, the odds ratio values of these factors were also different. The receiver operating characteristic curve showed that AR, SR1 and SR2 had cut-off values of 1.01, 1.48 and 1.40, respectively. SR3 (maximum size/PVD) was not associated with IAs rupture. IAs located in the ICA are associated with a negative risk of rupture, while high AR (>1.01), SR1 (>1.48) or SR2 (>1.40) are risk factors for multiple IAs rupture. Copyright © 2017 Hainan Medical University. Production and hosting by Elsevier B.V. All rights reserved.

Intact and Degraded Criticality Calculations for the Codisposal of Shippingport LWBR Spent Nuclear Fuel in a Waste Package

DOE Office of Scientific and Technical Information (OSTI.GOV)

L.M. Montierth

2000-09-15

The objective of this calculation is to characterize the nuclear criticality safety concerns associated with the codisposal of the U.S. Department of Energy's (DOE) Shippingport Light Water Breeder Reactor (SP LWBR) Spent Nuclear Fuel (SNF) in a 5-Defense High-Level Waste (5-DHLW) Waste Package (WP), which is to be placed in a Monitored Geologic Repository (MGR). The scope of this calculation is limited to the determination of the effective neutron multiplication factor (K{sub eff}) for intact- and degraded-mode internal configurations of the codisposal WP containing Shippingport LWBR seed-type assemblies. The results of this calculation will be used to evaluate criticality issuesmore » and support the analysis that is planed to be performed to demonstrate the viability of the codisposal concept for the MGR. This calculation is associated with the waste package design and was performed in accordance with the DOE SNF Analysis Plan for FY 2000 (See Ref. 22). The document has been prepared in accordance with the Administrative Procedure AP-3.12Q, Calculations (Ref. 23).« less

Stabilizing canonical-ensemble calculations in the auxiliary-field Monte Carlo method

NASA Astrophysics Data System (ADS)

Gilbreth, C. N.; Alhassid, Y.

2015-03-01

Quantum Monte Carlo methods are powerful techniques for studying strongly interacting Fermi systems. However, implementing these methods on computers with finite-precision arithmetic requires careful attention to numerical stability. In the auxiliary-field Monte Carlo (AFMC) method, low-temperature or large-model-space calculations require numerically stabilized matrix multiplication. When adapting methods used in the grand-canonical ensemble to the canonical ensemble of fixed particle number, the numerical stabilization increases the number of required floating-point operations for computing observables by a factor of the size of the single-particle model space, and thus can greatly limit the systems that can be studied. We describe an improved method for stabilizing canonical-ensemble calculations in AFMC that exhibits better scaling, and present numerical tests that demonstrate the accuracy and improved performance of the method.

Particle multiplicities in lead-lead collisions at the CERN large hadron collider from nonlinear evolution with running coupling corrections.

PubMed

Albacete, Javier L

2007-12-31

We present predictions for the pseudorapidity density of charged particles produced in central Pb-Pb collisions at the LHC. Particle production in such collisions is calculated in the framework of k(t) factorization. The nuclear unintegrated gluon distributions at LHC energies are determined from numerical solutions of the Balitsky-Kovchegov equation including recently calculated running coupling corrections. The initial conditions for the evolution are fixed by fitting Relativistic Heavy Ion Collider data at collision energies square root[sNN]=130 and 200 GeV per nucleon. We obtain dNch(Pb-Pb)/deta(square root[sNN]=5.5 TeV)/eta=0 approximately 1290-1480.

Detour factors in water and plastic phantoms and their use for range and depth scaling in electron-beam dosimetry.

PubMed

Fernández-Varea, J M; Andreo, P; Tabata, T

1996-07-01

Average penetration depths and detour factors of 1-50 MeV electrons in water and plastic materials have been computed by means of analytical calculation, within the continuous-slowing-down approximation and including multiple scattering, and using the Monte Carlo codes ITS and PENELOPE. Results are compared to detour factors from alternative definitions previously proposed in the literature. Different procedures used in low-energy electron-beam dosimetry to convert ranges and depths measured in plastic phantoms into water-equivalent ranges and depths are analysed. A new simple and accurate scaling method, based on Monte Carlo-derived ratios of average electron penetration depths and thus incorporating the effect of multiple scattering, is presented. Data are given for most plastics used in electron-beam dosimetry together with a fit which extends the method to any other low-Z plastic material. A study of scaled depth-dose curves and mean energies as a function of depth for some plastics of common usage shows that the method improves the consistency and results of other scaling procedures in dosimetry with electron beams at therapeutic energies.

Normalized impact factor (NIF): an adjusted method for calculating the citation rate of biomedical journals.

PubMed

Owlia, P; Vasei, M; Goliaei, B; Nassiri, I

2011-04-01

The interests in journal impact factor (JIF) in scientific communities have grown over the last decades. The JIFs are used to evaluate journals quality and the papers published therein. JIF is a discipline specific measure and the comparison between the JIF dedicated to different disciplines is inadequate, unless a normalization process is performed. In this study, normalized impact factor (NIF) was introduced as a relatively simple method enabling the JIFs to be used when evaluating the quality of journals and research works in different disciplines. The NIF index was established based on the multiplication of JIF by a constant factor. The constants were calculated for all 54 disciplines of biomedical field during 2005, 2006, 2007, 2008 and 2009 years. Also, ranking of 393 journals in different biomedical disciplines according to the NIF and JIF were compared to illustrate how the NIF index can be used for the evaluation of publications in different disciplines. The findings prove that the use of the NIF enhances the equality in assessing the quality of research works produced by researchers who work in different disciplines. Copyright © 2010 Elsevier Inc. All rights reserved.

Influence of socio-economic factors on emotional changes during the postnatal period.

PubMed

Wszołek, Katarzyna; Żak, Ewa; Żurawska, Joanna; Olszewska, Jolanta; Pięta, Beata; Bojar, Iwona

2018-03-14

The aim of the study was to identify socio-economic factors that may influence the emotional changes which occur among new mothers in the first days postpartum. A group of 541 women completed a questionnaire consisting of 30 multiple-choice questions, Edinburgh Postnatal Depression Scale (EPDS), and Hospital Anxiety and Depression Scale (HADS). Statistical calculations were performed with the use of Statistica v.10 and Cytel Studio v. 9.0.0. The findings revealed the presence of factors which might increase the risk of mood disorders during the postpartum period. Women who demonstrate warning symptoms should be screened for postnatal emotional changes and mood swings during their hospitalization after delivery. EPDS seems to be a suitable tool for early detection of emotional disturbances.

Short Physical Performance Battery for cardiovascular disease inpatients: implications for critical factors and sarcopenia.

PubMed

Yasuda, Tomohiro; Nakajima, Toshiaki; Sawaguchi, Tatsuya; Nozawa, Naohiro; Arakawa, Tomoe; Takahashi, Reiko; Mizushima, Yuta; Katayanagi, Satoshi; Matsumoto, Kazuhisa; Toyoda, Shigeru; Inoue, Teruo

2017-12-12

We examined the relationship between Short Physical Performance Battery (SPPB) and clinical and laboratory factors and the effect of sarcopenia and sarcopenic obesity (SO) on clinical and laboratory factors for cardiovascular disease (CVD) inpatients. CVD male (n = 318) and female (n = 172) inpatients were recruited. A stepwise multiple-regression analysis was performed to predict total SPPB scores and assess clinical and laboratory factors (physical characteristics, functional and morphological assessments, etc.). Each test outcome were compared among sarcopenia, SO and non-sarcopenic groups. To predict total SPPB scores, the predicted handgrip, Controlling Nutritional Status score, % body fat, anterior mid-thigh muscle thickness, standing height and systolic blood pressure were calculated for males and anterior mid-thigh MTH, BMI, knee extension and fat mass were calculated for females. There were no differences in blood pressure, total SPPB scores and functional assessments between sarcopenia and SO groups for CVD male and female inpatients. In conclusion, the physical performance of CVD inpatients can be predicted by nutritional, functional, clinical and anthropometric variables, regardless the gender and the presence of sarcopenia. Furthermore, the presence of sarcopenia has a negative effect on the clinical and laboratory factors, but there is a difference in impact between sarcopenia and SO regardless the gender.

Prediction of human core body temperature using non-invasive measurement methods.

PubMed

Niedermann, Reto; Wyss, Eva; Annaheim, Simon; Psikuta, Agnes; Davey, Sarah; Rossi, René Michel

2014-01-01

The measurement of core body temperature is an efficient method for monitoring heat stress amongst workers in hot conditions. However, invasive measurement of core body temperature (e.g. rectal, intestinal, oesophageal temperature) is impractical for such applications. Therefore, the aim of this study was to define relevant non-invasive measures to predict core body temperature under various conditions. We conducted two human subject studies with different experimental protocols, different environmental temperatures (10 °C, 30 °C) and different subjects. In both studies the same non-invasive measurement methods (skin temperature, skin heat flux, heart rate) were applied. A principle component analysis was conducted to extract independent factors, which were then used in a linear regression model. We identified six parameters (three skin temperatures, two skin heat fluxes and heart rate), which were included for the calculation of two factors. The predictive value of these factors for core body temperature was evaluated by a multiple regression analysis. The calculated root mean square deviation (rmsd) was in the range from 0.28 °C to 0.34 °C for all environmental conditions. These errors are similar to previous models using non-invasive measures to predict core body temperature. The results from this study illustrate that multiple physiological parameters (e.g. skin temperature and skin heat fluxes) are needed to predict core body temperature. In addition, the physiological measurements chosen in this study and the algorithm defined in this work are potentially applicable as real-time core body temperature monitoring to assess health risk in broad range of working conditions.

Hanford Technical Basis for Multiple Dosimetry Effective Dose Methodology

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hill, Robin L.; Rathbone, Bruce A.

2010-08-01

The current method at Hanford for dealing with the results from multiple dosimeters worn during non-uniform irradiation is to use a compartmentalization method to calculate the effective dose (E). The method, as documented in the current version of Section 6.9.3 in the 'Hanford External Dosimetry Technical Basis Manual, PNL-MA-842,' is based on the compartmentalization method presented in the 1997 ANSI/HPS N13.41 standard, 'Criteria for Performing Multiple Dosimetry.' With the adoption of the ICRP 60 methodology in the 2007 revision to 10 CFR 835 came changes that have a direct affect on the compartmentalization method described in the 1997 ANSI/HPS N13.41more » standard, and, thus, to the method used at Hanford. The ANSI/HPS N13.41 standard committee is in the process of updating the standard, but the changes to the standard have not yet been approved. And, the drafts of the revision of the standard tend to align more with ICRP 60 than with the changes specified in the 2007 revision to 10 CFR 835. Therefore, a revised method for calculating effective dose from non-uniform external irradiation using a compartmental method was developed using the tissue weighting factors and remainder organs specified in 10 CFR 835 (2007).« less

Deconstructing Calculation Methods, Part 3: Multiplication

ERIC Educational Resources Information Center

Thompson, Ian

2008-01-01

In this third of a series of four articles, the author deconstructs the primary national strategy's approach to written multiplication. The approach to multiplication, as set out on pages 12 to 15 of the primary national strategy's "Guidance paper" "Calculation" (DfES, 2007), is divided into six stages: (1) mental…

Prospective high thermoelectric performance of the heavily p -doped half-Heusler compound CoVSn

DOE PAGES

Shi, Hongliang; Ming, Wenmei; Parker, David S.; ...

2017-05-11

The electronic structure and transport properties of the half-Heusler compound CoVSn are studied in this paper systematically by combining first-principles electronic structure calculations and Boltzmann transport theory. The band structure at the valence-band edge is complex with multiple maxima derived from hybridized transition element d states. The result is a calculated thermopower larger than 200 μV /Κ within a wide range of doping concentrations and temperatures for heavily doped p-type CoVSn. The thermoelectric properties additionally benefit from the corrugated shapes of the hole pockets in our calculated isoenergy surfaces. Our calculated power factor S 2σ/τ (with respect to an averagemore » unknown scattering time) of CoVSn is comparable to that of FeNbSb. A smaller lattice thermal conductivity can be expected from the smaller group velocities of acoustical modes compared to FeNbSb. Finally, overall, good thermoelectric performance for CoVSn can be expected by considering the electronic transport and lattice thermal conductivity.« less

Silicon Oxysulfide, OSiS: Rotational Spectrum, Quantum-Chemical Calculations, and Equilibrium Structure.

PubMed

Thorwirth, Sven; Mück, Leonie Anna; Gauss, Jürgen; Tamassia, Filippo; Lattanzi, Valerio; McCarthy, Michael C

2011-06-02

Silicon oxysulfide, OSiS, and seven of its minor isotopic species have been characterized for the first time in the gas phase at high spectral resolution by means of Fourier transform microwave spectroscopy. The equilibrium structure of OSiS has been determined from the experimental data using calculated vibration-rotation interaction constants. The structural parameters (rO-Si = 1.5064 Å and rSi-S = 1.9133 Å) are in very good agreement with values from high-level quantum chemical calculations using coupled-cluster techniques together with sophisticated additivity and extrapolation schemes. The bond distances in OSiS are very short in comparison with those in SiO and SiS. This unexpected finding is explained by the partial charges calculated for OSiS via a natural population analysis. The results suggest that electrostatic effects rather than multiple bonding are the key factors in determining bonding in this triatomic molecule. The data presented provide the spectroscopic information needed for radio astronomical searches for OSiS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Simonen, E.P.; Johnson, K.I.; Simonen, F.A.

The Vessel Integrity Simulation Analysis (VISA-II) code was developed to allow calculations of the failure probability of a reactor pressure vessel subject to defined pressure/temperature transients. A version of the code, revised by Pacific Northwest Laboratory for the US Nuclear Regulatory Commission, was used to evaluate the sensitivities of calculated through-wall flaw probability to material, flaw and calculational assumptions. Probabilities were more sensitive to flaw assumptions than to material or calculational assumptions. Alternative flaw assumptions changed the probabilities by one to two orders of magnitude, whereas alternative material assumptions typically changed the probabilities by a factor of two or less.more » Flaw shape, flaw through-wall position and flaw inspection were sensitivities examined. Material property sensitivities included the assumed distributions in copper content and fracture toughness. Methods of modeling flaw propagation that were evaluated included arrest/reinitiation toughness correlations, multiple toughness values along the length of a flaw, flaw jump distance for each computer simulation and added error in estimating irradiated properties caused by the trend curve correlation error.« less

Prospective high thermoelectric performance of the heavily p -doped half-Heusler compound CoVSn

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Hongliang; Ming, Wenmei; Parker, David S.

The electronic structure and transport properties of the half-Heusler compound CoVSn are studied in this paper systematically by combining first-principles electronic structure calculations and Boltzmann transport theory. The band structure at the valence-band edge is complex with multiple maxima derived from hybridized transition element d states. The result is a calculated thermopower larger than 200 μV /Κ within a wide range of doping concentrations and temperatures for heavily doped p-type CoVSn. The thermoelectric properties additionally benefit from the corrugated shapes of the hole pockets in our calculated isoenergy surfaces. Our calculated power factor S 2σ/τ (with respect to an averagemore » unknown scattering time) of CoVSn is comparable to that of FeNbSb. A smaller lattice thermal conductivity can be expected from the smaller group velocities of acoustical modes compared to FeNbSb. Finally, overall, good thermoelectric performance for CoVSn can be expected by considering the electronic transport and lattice thermal conductivity.« less

Approach for validating actinide and fission product compositions for burnup credit criticality safety analyses

DOE PAGES

Radulescu, Georgeta; Gauld, Ian C.; Ilas, Germina; ...

2014-11-01

This paper describes a depletion code validation approach for criticality safety analysis using burnup credit for actinide and fission product nuclides in spent nuclear fuel (SNF) compositions. The technical basis for determining the uncertainties in the calculated nuclide concentrations is comparison of calculations to available measurements obtained from destructive radiochemical assay of SNF samples. Probability distributions developed for the uncertainties in the calculated nuclide concentrations were applied to the SNF compositions of a criticality safety analysis model by the use of a Monte Carlo uncertainty sampling method to determine bias and bias uncertainty in effective neutron multiplication factor. Application ofmore » the Monte Carlo uncertainty sampling approach is demonstrated for representative criticality safety analysis models of pressurized water reactor spent fuel pool storage racks and transportation packages using burnup-dependent nuclide concentrations calculated with SCALE 6.1 and the ENDF/B-VII nuclear data. Furthermore, the validation approach and results support a recent revision of the U.S. Nuclear Regulatory Commission Interim Staff Guidance 8.« less

Protein Turnover Measurements in Human Serum by Serial Immunoaffinity LC-MS/MS.

PubMed

Farrokhi, Vahid; Chen, Xiaoying; Neubert, Hendrik

2018-02-01

The half-life of target proteins is frequently an important parameter in mechanistic pharmacokinetic and pharmacodynamic (PK/PD) modeling of biotherapeutics. Clinical studies for accurate measurement of physiologically relevant protein turnover can reduce the uncertainty in PK/PD model-based predictions, for example, of the therapeutic dose and dosing regimen in first-in-human clinical trials. We used a targeted mass spectrometry work flow based on serial immunoaffinity enrichment ofmultiple human serum proteins from a [5,5,5- 2 H 3 ]-L-leucine tracer pulse-chase study in healthy volunteers. To confirm the reproducibility of turnover measurements from serial immunoaffinity enrichment, multiple aliquots from the same sample set were subjected to protein turnover analysis in varying order. Tracer incorporation was measured by multiple-reaction-monitoring mass spectrometry and target turnover was calculated using a four-compartment pharmacokinetic model. Five proteins of clinical or therapeutic relevance including soluble tumor necrosis factor receptor superfamily member 12A, tissue factor pathway inhibitor, soluble interleukin 1 receptor like 1, soluble mucosal addressin cell adhesion molecule 1, and muscle-specific creatine kinase were sequentially subjected to turnover analysis from the same human serum sample. Calculated half-lives ranged from 5-15 h; however, no tracer incorporation was observed for mucosal addressin cell adhesion molecule 1. The utility of clinical pulse-chase studies to investigate protein turnover can be extended by serial immunoaffinity enrichment of target proteins. Turnover analysis from serum and subsequently from remaining supernatants provided analytical sensitivity and reproducibility for multiple human target proteins in the same sample set, irrespective of the order of analysis. © 2017 American Association for Clinical Chemistry.

Determinants of sick-leave duration: a tool for managers?

PubMed

Flach, Peter A; Krol, Boudien; Groothoff, Johan W

2008-09-01

To provide managers with tools to manage episodes of sick-leave of their employees, the influence of factors such as age, gender, duration of tenure, working full-time or part-time, cause and history of sick-leave, salary and education on sick-leave duration was studied. In a cross-sectional study, data derived from the 2005 sick-leave files of a Dutch university were examined. Odds ratios of the single risk factors were calculated for short spells (or=91 days) of sick-leave. Next, these factors were studied in multiple regression models. Age, gender, duration of employment, cause and history of sick-leave, salary and membership of scientific staff, studied as single factors, have a significant influence on sick-leave duration. In multiple models, this influence remains for gender, salary, age, and history and cause of sick-leave. Only in medium or long spells and regarding the risk for a long or an extended spell do the predictive values of models consisting of psychological factors, work-related factors, salary and gender become reasonable. The predictive value of the risk factors used in this study is limited, and varies with the duration of the sick-leave spell. Only the risk for an extended spell of sick-leave as compared to a medium or long spell is reasonably predicted. Factors contributing to this risk may be used as tools in decision-making.

Nucleon electromagnetic form factors using lattice simulations at the physical point

NASA Astrophysics Data System (ADS)

Alexandrou, C.; Constantinou, M.; Hadjiyiannakou, K.; Jansen, K.; Kallidonis, Ch.; Koutsou, G.; Vaquero Aviles-Casco, A.

2017-08-01

We present results for the nucleon electromagnetic form factors using an ensemble of maximally twisted mass clover-improved fermions with pion mass of about 130 MeV. We use multiple sink-source separations and three analysis methods to probe ground-state dominance. We evaluate both the connected and disconnected contributions to the nucleon matrix elements. We find that the disconnected quark loop contributions to the isoscalar matrix elements are small, giving an upper bound of up to 2% of the connected and smaller than its statistical error. We present results for the isovector and isoscalar electric and magnetic Sachs form factors and the corresponding proton and neutron form factors. By fitting the momentum dependence of the form factors to a dipole form or to the z expansion, we extract the nucleon electric and magnetic radii, as well as the magnetic moment. We compare our results to experiment as well as to other recent lattice QCD calculations.

In-flight radiometric calibration of the Airborne Visible/Infrared Imaging Spectrometer (AVIRIS)

NASA Technical Reports Server (NTRS)

Conel, James E.; Green, Robert O.; Alley, Ronald E.; Bruegge, Carol J.; Carrere, Veronique; Margolis, Jack S.; Vane, Gregg; Chrien, Thomas G.; Slater, Philip N.; Biggard, Stuart F.

1988-01-01

A reflectance-based method was used to provide an analysis of the in-flight radiometric performance of AVIRIS. Field spectral reflectance measurements of the surface and extinction measurements of the atmosphere using solar radiation were used as input to atmospheric radiative transfer calculations. Five separate codes were used in the analysis. Four include multiple scattering, and the computed radiances from these for flight conditions were in good agreement. Code-generated radiances were compared with AVIRIS-predicted radiances based on two laboratory calibrations (pre- and post-season of flight) for a uniform highly reflecting natural dry lake target. For one spectrometer (C), the pre- and post-season calibration factors were found to give identical results, and to be in agreement with the atmospheric models that include multiple scattering. This positive result validates the field and laboratory calibration technique. Results for the other spectrometers (A, B and D) were widely at variance with the models no matter which calibration factors were used. Potential causes of these discrepancies are discussed.

Teaching strategies in the learning of highest common factor and lowest common multiple

NASA Astrophysics Data System (ADS)

Halim, N. L. A.; Li, H.-C.; Shahrill, M.; Prahmana, R. C. I.

2017-12-01

The main purpose of this study is to improve students’ understanding of Highest Common Factor (HCF) and Lowest Common Multiple (LCM). Several alternative teaching strategies were integrated in the Year 7 lessons involving 20 students from one secondary school in Brunei Darussalam. The categories identified in the teaching strategy were the application of group work, embedding real-life problems, using presentations and the traditional drilling practice method. An open-ended survey was disseminated to collate the students’ feedback, and among the questions posed was in relation to the different types of lesson activities utilised within each of the teaching strategies. Although 55% of the students preferred the traditional drilling practice on the calculation of HCF and LCM, mainly due to the ease of the task as opposed to activities involving real-life problems, the findings also indicated that most students favour sharing their ideas in a healthy competition learning style between each other or between the groups.

Lidar inelastic multiple-scattering parameters of cirrus particle ensembles determined with geometrical-optics crystal phase functions.

PubMed

Reichardt, J; Hess, M; Macke, A

2000-04-20

Multiple-scattering correction factors for cirrus particle extinction coefficients measured with Raman and high spectral resolution lidars are calculated with a radiative-transfer model. Cirrus particle-ensemble phase functions are computed from single-crystal phase functions derived in a geometrical-optics approximation. Seven crystal types are considered. In cirrus clouds with height-independent particle extinction coefficients the general pattern of the multiple-scattering parameters has a steep onset at cloud base with values of 0.5-0.7 followed by a gradual and monotonic decrease to 0.1-0.2 at cloud top. The larger the scattering particles are, the more gradual is the rate of decrease. Multiple-scattering parameters of complex crystals and of imperfect hexagonal columns and plates can be well approximated by those of projected-area equivalent ice spheres, whereas perfect hexagonal crystals show values as much as 70% higher than those of spheres. The dependencies of the multiple-scattering parameters on cirrus particle spectrum, base height, and geometric depth and on the lidar parameters laser wavelength and receiver field of view, are discussed, and a set of multiple-scattering parameter profiles for the correction of extinction measurements in homogeneous cirrus is provided.

A Simple and Convenient Method of Multiple Linear Regression to Calculate Iodine Molecular Constants

ERIC Educational Resources Information Center

Cooper, Paul D.

2010-01-01

A new procedure using a student-friendly least-squares multiple linear-regression technique utilizing a function within Microsoft Excel is described that enables students to calculate molecular constants from the vibronic spectrum of iodine. This method is advantageous pedagogically as it calculates molecular constants for ground and excited…

Factors associated with mouth breathing in children with -developmental -disabilities.

PubMed

de Castilho, Lia Silva; Abreu, Mauro Henrique Nogueira Guimarães; de Oliveira, Renata Batista; Souza E Silva, Maria Elisa; Resende, Vera Lúcia Silva

2016-01-01

To investigate the prevalence and factors associated with mouth breathing among patients with developmental disabilities of a dental service. We analyzed 408 dental records. Mouth breathing was reported by the patients' parents and from direct observation. Other variables were as -follows: history of asthma, bronchitis, palate shape, pacifier use, thumb -sucking, nail biting, use of medications, gastroesophageal reflux, bruxism, gender, age, and diagnosis of the patient. Statistical analysis included descriptive analysis with ratio calculation and multiple logistic regression. Variables with p < 0.25 were included in the model to estimate the adjusted OR (95% CI), calculated by the forward stepwise method. Variables with p ​​< 0.05 were kept in the model. Being male (p = 0.016) and use of centrally acting drugs (p = 0.001) were the variables that remained in the model. Among patients with -developmental disabilities, boys and psychotropic drug users had a greater chance of being mouth breathers. © 2016 Special Care Dentistry Association and Wiley Periodicals, Inc.

The mechanical properties of high speed GTAW weld and factors of nonlinear multiple regression model under external transverse magnetic field

NASA Astrophysics Data System (ADS)

Lu, Lin; Chang, Yunlong; Li, Yingmin; He, Youyou

2013-05-01

A transverse magnetic field was introduced to the arc plasma in the process of welding stainless steel tubes by high-speed Tungsten Inert Gas Arc Welding (TIG for short) without filler wire. The influence of external magnetic field on welding quality was investigated. 9 sets of parameters were designed by the means of orthogonal experiment. The welding joint tensile strength and form factor of weld were regarded as the main standards of welding quality. A binary quadratic nonlinear regression equation was established with the conditions of magnetic induction and flow rate of Ar gas. The residual standard deviation was calculated to adjust the accuracy of regression model. The results showed that, the regression model was correct and effective in calculating the tensile strength and aspect ratio of weld. Two 3D regression models were designed respectively, and then the impact law of magnetic induction on welding quality was researched.

Alternative Beam Efficiency Calculations for a Large-aperture Multiple-frequency Microwave Radiometer (LAMMR)

NASA Technical Reports Server (NTRS)

Schmidt, R. F.

1979-01-01

The fundamental definition of beam efficiency, given in terms of a far field radiation pattern, was used to develop alternative definitions which improve accuracy, reduce the amount of calculation required, and isolate the separate factors composing beam efficiency. Well-known definitions of aperture efficiency were introduced successively to simplify the denominator of the fundamental definition. The superposition of complex vector spillover and backscattered fields was examined, and beam efficiency analysis in terms of power patterns was carried out. An extension from single to dual reflector geometries was included. It is noted that the alternative definitions are advantageous in the mathematical simulation of a radiometer system, and are not intended for the measurements discipline where fields have merged and therefore lost their identity.

Equilibrium fractionation of H and O isotopes in water from path integral molecular dynamics

NASA Astrophysics Data System (ADS)

Pinilla, Carlos; Blanchard, Marc; Balan, Etienne; Ferlat, Guillaume; Vuilleumier, Rodolphe; Mauri, Francesco

2014-06-01

The equilibrium fractionation factor between two phases is of importance for the understanding of many planetary and environmental processes. Although thermodynamic equilibrium can be achieved between minerals at high temperature, many natural processes involve reactions between liquids or aqueous solutions and solids. For crystals, the fractionation factor α can be theoretically determined using a statistical thermodynamic approach based on the vibrational properties of the phases. These calculations are mostly performed in the harmonic approximation, using empirical or ab-initio force fields. In the case of aperiodic and dynamic systems such as liquids or solutions, similar calculations can be done using finite-size molecular clusters or snapshots obtained from molecular dynamics (MD) runs. It is however difficult to assess the effect of these approximate models on the isotopic fractionation properties. In this work we present a systematic study of the calculation of the D/H and 18O/16O equilibrium fractionation factors in water for the liquid/vapour and ice/vapour phases using several levels of theory within the simulations. Namely, we use a thermodynamic integration approach based on Path Integral MD calculations (PIMD) and an empirical potential model of water. Compared with standard MD, PIMD takes into account quantum effects in the thermodynamic modeling of systems and the exact fractionation factor for a given potential can be obtained. We compare these exact results with those of modeling strategies usually used, which involve the mapping of the quantum system on its harmonic counterpart. The results show the importance of including configurational disorder for the estimation of isotope fractionation in liquid phases. In addition, the convergence of the fractionation factor as a function of parameters such as the size of the simulated system and multiple isotope substitution is analyzed, showing that isotope fractionation is essentially a local effect in the investigated system.

Errors induced by the neglect of polarization in radiance calculations for Rayleigh-scattering atmospheres

NASA Technical Reports Server (NTRS)

Mishchenko, M. I.; Lacis, A. A.; Travis, L. D.

1994-01-01

Although neglecting polarization and replacing the rigorous vector radiative transfer equation by its approximate scalar counterpart has no physical background, it is a widely used simplification when the incident light is unpolarized and only the intensity of the reflected light is to be computed. We employ accurate vector and scalar multiple-scattering calculations to perform a systematic study of the errors induced by the neglect of polarization in radiance calculations for a homogeneous, plane-parallel Rayleigh-scattering atmosphere (with and without depolarization) above a Lambertian surface. Specifically, we calculate percent errors in the reflected intensity for various directions of light incidence and reflection, optical thicknesses of the atmosphere, single-scattering albedos, depolarization factors, and surface albedos. The numerical data displayed can be used to decide whether or not the scalar approximation may be employed depending on the parameters of the problem. We show that the errors decrease with increasing depolarization factor and/or increasing surface albedo. For conservative or nearly conservative scattering and small surface albedos, the errors are maximum at optical thicknesses of about 1. The calculated errors may be too large for some practical applications, and, therefore, rigorous vector calculations should be employed whenever possible. However, if approximate scalar calculations are used, we recommend to avoid geometries involving phase angles equal or close to 0 deg and 90 deg, where the errors are especially significant. We propose a theoretical explanation of the large vector/scalar differences in the case of Rayleigh scattering. According to this explanation, the differences are caused by the particular structure of the Rayleigh scattering matrix and come from lower-order (except first-order) light scattering paths involving right scattering angles and right-angle rotations of the scattering plane.

SU-F-T-192: Study of Robustness Analysis Method of Multiple Field Optimized IMPT Plans for Head & Neck Patients

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Y; Wang, X; Li, H

Purpose: Proton therapy is more sensitive to uncertainties than photon treatments due to protons’ finite range depending on the tissue density. Worst case scenario (WCS) method originally proposed by Lomax has been adopted in our institute for robustness analysis of IMPT plans. This work demonstrates that WCS method is sufficient enough to take into account of the uncertainties which could be encountered during daily clinical treatment. Methods: A fast and approximate dose calculation method is developed to calculate the dose for the IMPT plan under different setup and range uncertainties. Effects of two factors, inversed square factor and range uncertainty,more » are explored. WCS robustness analysis method was evaluated using this fast dose calculation method. The worst-case dose distribution was generated by shifting isocenter by 3 mm along x,y and z directions and modifying stopping power ratios by ±3.5%. 1000 randomly perturbed cases in proton range and x, yz directions were created and the corresponding dose distributions were calculated using this approximated method. DVH and dosimetric indexes of all 1000 perturbed cases were calculated and compared with the result using worst case scenario method. Results: The distributions of dosimetric indexes of 1000 perturbed cases were generated and compared with the results using worst case scenario. For D95 of CTVs, at least 97% of 1000 perturbed cases show higher values than the one of worst case scenario. For D5 of CTVs, at least 98% of perturbed cases have lower values than worst case scenario. Conclusion: By extensively calculating the dose distributions under random uncertainties, WCS method was verified to be reliable in evaluating the robustness level of MFO IMPT plans of H&N patients. The extensively sampling approach using fast approximated method could be used in evaluating the effects of different factors on the robustness level of IMPT plans in the future.« less

A quantitative visual dashboard to explore exposures to ...

EPA Pesticide Factsheets

The Exposure Prioritization (Ex Priori) model features a simplified, quantitative visual dashboard to explore exposures across chemical space. Diverse data streams are integrated within the interface such that different exposure scenarios for “individual,” “population,” or “professional” time-use profiles can be interchanged to tailor exposure and quantitatively explore multi-chemical signatures of exposure, internalized dose (uptake), body burden, and elimination. Ex Priori will quantitatively extrapolate single-point estimates of both exposure and internal dose for multiple exposure scenarios, factors, products, and pathways. Currently, EPA is investigating its usefulness in life cycle analysis, insofar as its ability to enhance exposure factors used in calculating characterization factors for human health. Presented at 2016 Annual ISES Meeting held in Utrecht, The Netherlands, from 9-13 October 2016.

Dirac and Pauli form factors from lattice QCD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Collins, S.; Goeckeler, M.; Nobile, A.

2011-10-01

We present a comprehensive analysis of the electromagnetic form factors of the nucleon from a lattice simulation with two flavors of dynamical O(a)-improved Wilson fermions. A key feature of our calculation is that we make use of an extensive ensemble of lattice gauge field configurations with four different lattice spacings, multiple volumes, and pion masses down to m{sub {pi}{approx}1}80 MeV. We find that by employing Kelly-inspired parametrizations for the Q{sup 2} dependence of the form factors, we are able to obtain stable fits over our complete ensemble. Dirac and Pauli radii and the anomalous magnetic moments of the nucleon aremore » extracted and results at light quark masses provide evidence for chiral nonanalytic behavior in these fundamental observables.« less

Joint analysis of multiple biomarkers for identifying type 2 diabetes in middle-aged and older Chinese: a cross-sectional study

PubMed Central

Wu, Hongyu; Yu, Zhijie; Qi, Qibin; Li, Huaixing; Sun, Qi

2011-01-01

Objective Identifying individuals with high risk of type 2 diabetes is important. To evaluate discriminatory ability of multiple biomarkers for type 2 diabetes in a Chinese population. Methods Plasma adiponectin, plasminogen activator inhibitor-1, retinol-binding protein 4, resistin, C-reactive protein, interleukin 6 (IL-6), tumour necrosis factor α receptor 2 and ferritin were measured in a population-based sample of 3189 Chinese (1419 men and 1770 women) aged 50–70 years. A weighted biomarkers risk score (BRS) was developed based on the strength of associations of these biomarkers with type 2 diabetes. The discriminatory ability was tested by the area under receiver operating characteristics curve (AUC). Results Adiponectin, plasminogen activator inhibitor-1, IL-6 and ferritin were independently associated with the prevalence of type 2 diabetes, and they were used to calculate the biomarkers risk score (BRS). After adjustment for the confounding factors, the ORs for type 2 diabetes and impaired fasting glucose with each point increment of BRS were 1.28 (95% CI 1.22 to 1.34) and 1.16 (1.12 to 1.20), respectively. Compared with those in the lowest quintile of the BRS, the participants in the highest quintile have an OR (95% CI) of 6.67 (4.21 to 10.55) for type 2 diabetes. The area under the curve for the BRS and conventional risk factors alone was 0.73 and 0.76, respectively, and substantially increased to 0.81 after combining both BRS and conventional risk factors (p<0.001). Conclusions These data suggest that combining multiple biomarkers and conventional risk factors might substantially enhance the ability to identify individuals with type 2 diabetes. More prospective data are warranted to confirm this observation. PMID:22021786

Right parietal cortex and calculation processing: intraoperative functional mapping of multiplication and addition in patients affected by a brain tumor.

PubMed

Della Puppa, Alessandro; De Pellegrin, Serena; d'Avella, Elena; Gioffrè, Giorgio; Munari, Marina; Saladini, Marina; Salillas, Elena; Scienza, Renato; Semenza, Carlo

2013-11-01

The role of parietal areas in number processing is well known. The significance of intraoperative functional mapping of these areas has been only partially explored, however, and only a few discordant data are available in the surgical literature with regard to the right parietal lobe. The purpose of this study was to evaluate the clinical impact of simple calculation in cortical electrostimulation of right-handed patients affected by a right parietal brain tumor. Calculation mapping in awake surgery was performed in 3 right-handed patients affected by high-grade gliomas located in the right parietal lobe. Preoperatively, none of the patients presented with calculation deficits. In all 3 cases, after sensorimotor and language mapping, cortical and intraparietal sulcus areas involved in single-digit multiplication and addition calculations were mapped using bipolar electrostimulation. In all patients, different sites of the right parietal cortex, mainly in the inferior lobule, were detected as being specifically related to calculation (multiplication or addition). In 2 patients the intraparietal sulcus was functionally specific for multiplication. No functional sites for language were detected. All sites functional for calculation were spared during tumor resection, which was complete in all cases without postoperative neurological deficits. These findings provide intraoperative data in support of an anatomofunctional organization for multiplication and addition within the right parietal area. Furthermore, the study shows the potential clinical relevance of intraoperative mapping of calculation in patients undergoing surgery in the right parietal area. Further and larger studies are needed to confirm these data and assess whether mapped areas are effectively essential for function.

The modelling influence of water content to mechanical parameter of soil in analysis of slope stability

NASA Astrophysics Data System (ADS)

Gusman, M.; Nazki, A.; Putra, R. R.

2018-04-01

One of the parameters in slope stability analysis is the shear strength of the soil. Changes in soil shear strength characteristics lead to a decrease in safety factors on the slopes. This study aims to see the effect of increased moisture content on soil mechanical parameters. The case study study was conducted on the slopes of Sitinjau Lauik Kota Padang. The research method was done by laboratory analysis and simple liniear regression analysis and multiple. Based on the test soil results show that the increase in soil water content causes a decrease in cohesion values and internal shear angle. The relationship of moisture content to cohesion is described in equation Y = 55.713-0,6X with R2 = 0.842. While the relationship of water content to shear angle in soil is described in the equation Y = 38.878-0.258X with R2 = 0.915. From several simulations of soil water level improvement, calculation of safety factor (SF) of slope. The calculation results show that the increase of groundwater content is very significant affect the safety factor (SF) slope. SF slope values are in safe condition when moisture content is 50% and when it reaches maximum water content 73.74% slope safety factor value potentially for landslide.

Polarimetry with multiple mirror telescopes

NASA Technical Reports Server (NTRS)

West, S. C.

1986-01-01

The polarizations of multiple mirror telescopes are calculated using Mueller calculus. It is found that the Multiple Mirror Telescope (MMT) produces a constant depolarization that is a function of wavelength and independent of sky position. The efficiency and crosstalk are modeled and experimentally verified. The two- and four-mirror new generation telescopes are found to produce sinusoidal depolarization for which an accurate interpretation of the incident Stokes vector requires inverse matrix calculations. Finally, the depolarization of f/1 paraboloids is calculated and found to be less than 0.1 percent at 3000 A.

Children's environmental chemical exposures in the USA, NHANES 2003-2012.

PubMed

Hendryx, Michael; Luo, Juhua

2018-02-01

Children are vulnerable to environmental chemical exposures, but little is known about the extent of multiple chemical exposures among children. We analyzed biomonitoring data from five cycles (2003-2012) of the National Health and Nutrition Examination Survey (NHANES) to describe multiple chemical exposures in US children, examine levels of chemical concentrations present over time, and examine differences in chemical exposures by selected demographic groups. We analyzed data for 36 chemical analytes across five chemical classes in a sample of 4299 children aged 6-18. Classes included metals, pesticides, phthalates, phenols, and polycyclic aromatic hydrocarbons. We calculated the number and percent of chemicals detected and tested for secular trends over time in chemical concentrations. We compared log concentrations among groups defined by age, sex, race/ethnicity, and poverty using multiple linear regression models and report adjusted geometric means. Among a smaller subgroup of 733 children with data across chemical classes, we calculated the linear correlations within and between classes and conducted a principal component analysis. The percentage of children with detectable concentrations of an individual chemical ranged from 26 to 100%; the average was 93%, and 29 of 36 were detected in more than 90% of children. Concentrations of most tested chemicals were either unchanged or declined from earlier to more recent years. Many differences in concentrations were present by age, sex, poverty, and race/ethnicity categories. Within and between class correlations were all significant and positive, and the principal component analysis suggested a one factor solution, indicating that children exposed to higher levels of one chemical were exposed to higher levels of other chemicals. In conclusion, children in the USA are exposed to multiple simultaneous chemicals at uneven risk across socioeconomic and demographic groups. Further efforts to understand the effects of multiple exposures on child health and development are warranted.

Association of dentine hypersensitivity with different risk factors - a cross sectional study.

PubMed

Vijaya, V; Sanjay, Venkataraam; Varghese, Rana K; Ravuri, Rajyalakshmi; Agarwal, Anil

2013-12-01

This study was done to assess the prevalence of Dentine hypersensitivity (DH) and its associated risk factors. This epidemiological study was done among patients coming to dental college regarding prevalence of DH. A self structured questionnaire along with clinical examination was done for assessment. Descriptive statistics were obtained and frequency distribution was calculated using Chi square test at p value <0.05. Stepwise multiple linear regression was also done to access frequency of DH with different factors. The study population was comprised of 655 participants with different age groups. Our study showed prevalence as 55% and it was more common among males. Similarly smokers and those who use hard tooth brush had more cases of DH. Step wise multiple linear regression showed that best predictor for DH was age followed by habit of smoking and type of tooth brush. Most aggravating factors were cold water (15.4%) and sweet foods (14.7%), whereas only 5% of the patients had it while brushing. A high level of dental hypersensitivity has been in this study and more common among males. A linear finding was shown with age, smoking and type of tooth brush. How to cite this article: Vijaya V, Sanjay V, Varghese RK, Ravuri R, Agarwal A. Association of Dentine Hypersensitivity with Different Risk Factors - A Cross Sectional Study. J Int Oral Health 2013;5(6):88-92 .

Development of Advanced Methods of Structural and Trajectory Analysis for Transport Aircraft

NASA Technical Reports Server (NTRS)

Ardema, Mark D.; Windhorst, Robert; Phillips, James

1998-01-01

This paper develops a near-optimal guidance law for generating minimum fuel, time, or cost fixed-range trajectories for supersonic transport aircraft. The approach uses a choice of new state variables along with singular perturbation techniques to time-scale decouple the dynamic equations into multiple equations of single order (second order for the fast dynamics). Application of the maximum principle to each of the decoupled equations, as opposed to application to the original coupled equations, avoids the two point boundary value problem and transforms the problem from one of a functional optimization to one of multiple function optimizations. It is shown that such an approach produces well known aircraft performance results such as minimizing the Brequet factor for minimum fuel consumption and the energy climb path. Furthermore, the new state variables produce a consistent calculation of flight path angle along the trajectory, eliminating one of the deficiencies in the traditional energy state approximation. In addition, jumps in the energy climb path are smoothed out by integration of the original dynamic equations at constant load factor. Numerical results performed for a supersonic transport design show that a pushover dive followed by a pullout at nominal load factors are sufficient maneuvers to smooth the jump.

Optimization of Supersonic Transport Trajectories

NASA Technical Reports Server (NTRS)

Ardema, Mark D.; Windhorst, Robert; Phillips, James

1998-01-01

This paper develops a near-optimal guidance law for generating minimum fuel, time, or cost fixed-range trajectories for supersonic transport aircraft. The approach uses a choice of new state variables along with singular perturbation techniques to time-scale decouple the dynamic equations into multiple equations of single order (second order for the fast dynamics). Application of the maximum principle to each of the decoupled equations, as opposed to application to the original coupled equations, avoids the two point boundary value problem and transforms the problem from one of a functional optimization to one of multiple function optimizations. It is shown that such an approach produces well known aircraft performance results such as minimizing the Brequet factor for minimum fuel consumption and the energy climb path. Furthermore, the new state variables produce a consistent calculation of flight path angle along the trajectory, eliminating one of the deficiencies in the traditional energy state approximation. In addition, jumps in the energy climb path are smoothed out by integration of the original dynamic equations at constant load factor. Numerical results performed for a supersonic transport design show that a pushover dive followed by a pullout at nominal load factors are sufficient maneuvers to smooth the jump.

Unmanned Multiple Exploratory Probe System (MEPS) for Mars observation. Volume 2: Calculations and derivations

NASA Technical Reports Server (NTRS)

Adams, Daniel E.; Crumbly, Christopher M.; Delp, Steve E.; Guidry, Michelle A.; Lisano, Michael E.; Packard, James D.; Striepe, Scott A.

1988-01-01

This volume of the final report on the unmanned Multiple Exploratory Probe System (MEPS) details all calculations, derivations, and computer programs that support the information presented in the first volume.

A Virtual Mixture Approach to the Study of Multistate Equilibrium: Application to Constant pH Simulation in Explicit Water

PubMed Central

Wu, Xiongwu; Brooks, Bernard R.

2015-01-01

Chemical and thermodynamic equilibrium of multiple states is a fundamental phenomenon in biology systems and has been the focus of many experimental and computational studies. This work presents a simulation method to directly study the equilibrium of multiple states. This method constructs a virtual mixture of multiple states (VMMS) to sample the conformational space of all chemical states simultaneously. The VMMS system consists of multiple subsystems, one for each state. The subsystem contains a solute and a solvent environment. The solute molecules in all subsystems share the same conformation but have their own solvent environments. Transition between states is implicated by the change of their molar fractions. Simulation of a VMMS system allows efficient calculation of relative free energies of all states, which in turn determine their equilibrium molar fractions. For systems with a large number of state transition sites, an implicit site approximation is introduced to minimize the cost of simulation. A direct application of the VMMS method is for constant pH simulation to study protonation equilibrium. Applying the VMMS method to a heptapeptide of 3 ionizable residues, we calculated the pKas of those residues both with all explicit states and with implicit sites and obtained consistent results. For mouse epidermal growth factor of 9 ionizable groups, our VMMS simulations with implicit sites produced pKas of all 9 ionizable groups and the results agree qualitatively with NMR measurement. This example demonstrates the VMMS method can be applied to systems of a large number of ionizable groups and the computational cost scales linearly with the number of ionizable groups. For one of the most challenging systems in constant pH calculation, SNase Δ+PHS/V66K, our VMMS simulation shows that it is the state-dependent water penetration that causes the large deviation in lysine66’s pKa. PMID:26506245

A Virtual Mixture Approach to the Study of Multistate Equilibrium: Application to Constant pH Simulation in Explicit Water.

PubMed

Wu, Xiongwu; Brooks, Bernard R

2015-10-01

Chemical and thermodynamic equilibrium of multiple states is a fundamental phenomenon in biology systems and has been the focus of many experimental and computational studies. This work presents a simulation method to directly study the equilibrium of multiple states. This method constructs a virtual mixture of multiple states (VMMS) to sample the conformational space of all chemical states simultaneously. The VMMS system consists of multiple subsystems, one for each state. The subsystem contains a solute and a solvent environment. The solute molecules in all subsystems share the same conformation but have their own solvent environments. Transition between states is implicated by the change of their molar fractions. Simulation of a VMMS system allows efficient calculation of relative free energies of all states, which in turn determine their equilibrium molar fractions. For systems with a large number of state transition sites, an implicit site approximation is introduced to minimize the cost of simulation. A direct application of the VMMS method is for constant pH simulation to study protonation equilibrium. Applying the VMMS method to a heptapeptide of 3 ionizable residues, we calculated the pKas of those residues both with all explicit states and with implicit sites and obtained consistent results. For mouse epidermal growth factor of 9 ionizable groups, our VMMS simulations with implicit sites produced pKas of all 9 ionizable groups and the results agree qualitatively with NMR measurement. This example demonstrates the VMMS method can be applied to systems of a large number of ionizable groups and the computational cost scales linearly with the number of ionizable groups. For one of the most challenging systems in constant pH calculation, SNase Δ+PHS/V66K, our VMMS simulation shows that it is the state-dependent water penetration that causes the large deviation in lysine66's pKa.

Problems and methods of calculating the Legendre functions of arbitrary degree and order

NASA Astrophysics Data System (ADS)

Novikova, Elena; Dmitrenko, Alexander

2016-12-01

The known standard recursion methods of computing the full normalized associated Legendre functions do not give the necessary precision due to application of IEEE754-2008 standard, that creates a problems of underflow and overflow. The analysis of the problems of the calculation of the Legendre functions shows that the problem underflow is not dangerous by itself. The main problem that generates the gross errors in its calculations is the problem named the effect of "absolute zero". Once appeared in a forward column recursion, "absolute zero" converts to zero all values which are multiplied by it, regardless of whether a zero result of multiplication is real or not. Three methods of calculating of the Legendre functions, that removed the effect of "absolute zero" from the calculations are discussed here. These methods are also of interest because they almost have no limit for the maximum degree of Legendre functions. It is shown that the numerical accuracy of these three methods is the same. But, the CPU calculation time of the Legendre functions with Fukushima method is minimal. Therefore, the Fukushima method is the best. Its main advantage is computational speed which is an important factor in calculation of such large amount of the Legendre functions as 2 401 336 for EGM2008.

Finite element and analytical solutions for van der Pauw and four-point probe correction factors when multiple non-ideal measurement conditions coexist

NASA Astrophysics Data System (ADS)

Reveil, Mardochee; Sorg, Victoria C.; Cheng, Emily R.; Ezzyat, Taha; Clancy, Paulette; Thompson, Michael O.

2017-09-01

This paper presents an extensive collection of calculated correction factors that account for the combined effects of a wide range of non-ideal conditions often encountered in realistic four-point probe and van der Pauw experiments. In this context, "non-ideal conditions" refer to conditions that deviate from the assumptions on sample and probe characteristics made in the development of these two techniques. We examine the combined effects of contact size and sample thickness on van der Pauw measurements. In the four-point probe configuration, we examine the combined effects of varying the sample's lateral dimensions, probe placement, and sample thickness. We derive an analytical expression to calculate correction factors that account, simultaneously, for finite sample size and asymmetric probe placement in four-point probe experiments. We provide experimental validation of the analytical solution via four-point probe measurements on a thin film rectangular sample with arbitrary probe placement. The finite sample size effect is very significant in four-point probe measurements (especially for a narrow sample) and asymmetric probe placement only worsens such effects. The contribution of conduction in multilayer samples is also studied and found to be substantial; hence, we provide a map of the necessary correction factors. This library of correction factors will enable the design of resistivity measurements with improved accuracy and reproducibility over a wide range of experimental conditions.

Finite element and analytical solutions for van der Pauw and four-point probe correction factors when multiple non-ideal measurement conditions coexist.

PubMed

Reveil, Mardochee; Sorg, Victoria C; Cheng, Emily R; Ezzyat, Taha; Clancy, Paulette; Thompson, Michael O

2017-09-01

This paper presents an extensive collection of calculated correction factors that account for the combined effects of a wide range of non-ideal conditions often encountered in realistic four-point probe and van der Pauw experiments. In this context, "non-ideal conditions" refer to conditions that deviate from the assumptions on sample and probe characteristics made in the development of these two techniques. We examine the combined effects of contact size and sample thickness on van der Pauw measurements. In the four-point probe configuration, we examine the combined effects of varying the sample's lateral dimensions, probe placement, and sample thickness. We derive an analytical expression to calculate correction factors that account, simultaneously, for finite sample size and asymmetric probe placement in four-point probe experiments. We provide experimental validation of the analytical solution via four-point probe measurements on a thin film rectangular sample with arbitrary probe placement. The finite sample size effect is very significant in four-point probe measurements (especially for a narrow sample) and asymmetric probe placement only worsens such effects. The contribution of conduction in multilayer samples is also studied and found to be substantial; hence, we provide a map of the necessary correction factors. This library of correction factors will enable the design of resistivity measurements with improved accuracy and reproducibility over a wide range of experimental conditions.

Soils as relative-age dating tools

USGS Publications Warehouse

Markewich, Helaine Walsh; Pavich, Milan J.; Wysocki, Douglas A.

2017-01-01

Soils develop at the earth's surface via multiple processes that act through time. Precluding burial or disturbance, soil genetic horizons form progressively and reflect the balance among formation processes, surface age, and original substrate composition. Soil morphology provides a key link between process and time (soil age), enabling soils to serve as both relative and numerical dating tools for geomorphic studies and landscape evolution. Five major factors define the contemporary state of all soils: climate, organisms, topography, parent material, and time. Soils developed on similar landforms and parent materials within a given landscape comprise what we term a soil/landform/substrate complex. Soils on such complexes that differ in development as a function of time represent a soil chronosequence. In a soil chronosequence, time constitutes the only independent formation factor; the other factors act through time. Time dictates the variations in soil development or properties (field or laboratory measured) on a soil/landform/substrate complex. Using a dataset within the chronosequence model, we can also formulate various soil development indices based upon one or a combination of soil properties, either for individual soil horizons or for an entire profile. When we evaluate soil data or soil indices mathematically, the resulting equation creates a chronofunction. Chronofunctions help quantify processes and mechanisms involved in soil development, and relate them mathematically to time. These rigorous kinds of comparisons among and within soil/landform complexes constitute an important tool for relative-age dating. After determining one or more absolute ages for a soil/landform complex, we can calculate quantitative soil formation, and or landform-development rates. Multiple dates for several complexes allow rate calculations for soil/landform-chronosequence development and soil-chronofunction calibration.

Multiple tobacco product use among adults in the United States: cigarettes, cigars, electronic cigarettes, hookah, smokeless tobacco, and snus.

PubMed

Lee, Youn O; Hebert, Christine J; Nonnemaker, James M; Kim, Annice E

2014-05-01

Noncigarette tobacco products are increasingly popular. Researchers need to understand multiple tobacco product use to assess the effects of these products on population health. We estimate national prevalence and examine risk factors for multiple product use. We calculated prevalence estimates of current use patterns involving cigarettes, cigars, electronic cigarettes, hookah, smokeless tobacco, and snus using data from the 2012 RTI National Adult Tobacco Survey (N=3627), a random-digit-dial telephone survey of adults aged 18 and over. Associations between use patterns (exclusive single product and multiple products) and demographic characteristics were examined using Pearson chi-square tests and logistic regression. 32.1% of adults currently use 1 or more tobacco products; 14.9% use cigarettes exclusively, and 6.6% use one noncigarette product exclusively, 6.9% use cigarettes with another product (dual use), 1.3% use two noncigarette products, and 2.4% use three or more products (polytobacco use). Smokers who are young adult, male, never married, reside in the West, and made prior quit attempts were at risk for multiple product use. Over 10% of U.S. adults use multiple tobacco products. A better understanding of multiple product use involving combustible products, like cigars and hookah, is needed. Multiple product use may be associated with past quit attempts. Copyright © 2014 Elsevier Inc. All rights reserved.

Therapeutic Effect of Gamma Knife Radiosurgery for Multiple Brain Metastases

PubMed Central

Lee, Chul-Kyu; Lee, Sang Ryul; Cho, Jin Mo; Yang, Kyung Ah

2011-01-01

Objective The aim of this study is to evaluate the therapeutic effects of gamma knife radiosurgery (GKRS) in patients with multiple brain metastases and to investigate prognostic factors related to treatment outcome. Methods We retrospectively reviewed clinico-radiological and dosimetric data of 36 patients with 4-14 brain metastases who underwent GKRS for 264 lesions between August 2008 and April 2011. The most common primary tumor site was the lung (n=22), followed by breast (n=7). At GKRS, the median Karnofsky performance scale score was 90 and the mean tumor volume was 1.2 cc (0.002-12.6). The mean prescription dose of 17.8 Gy was delivered to the mean 61.1% isodose line. Among 264 metastases, 175 lesions were assessed for treatment response by at least one imaging follow-up. Results The overall median survival after GKRS was 9.1±1.7 months. Among various factors, primary tumor control was a significant prognostic factor (11.1±1.3 months vs. 3.3±2.4 months, p=0.031). The calculated local tumor control rate at 6 and 9 months after GKRS were 87.9% and 84.2%, respectively. Paddick's conformity index (>0.75) was significantly related to local tumor control. The actuarial peritumoral edema reduction rate was 22.4% at 6 months. Conclusion According to our results, GKRS can provide beneficial effect for the patients with multiple (4 or more) brain metastases, when systemic cancer is controlled. And, careful dosimetry is essential for local tumor control. Therefore, GKRS can be considered as one of the treatment modalities for multiple brain metastase. PMID:22102945

First-principles multiple-barrier diffusion theory. The case study of interstitial diffusion in CdTe

DOE PAGES

Yang, Ji -Hui; Park, Ji -Sang; Kang, Joongoo; ...

2015-02-17

The diffusion of particles in solid-state materials generally involves several sequential thermal-activation processes. However, presently, diffusion coefficient theory only deals with a single barrier, i.e., it lacks an accurate description to deal with multiple-barrier diffusion. Here, we develop a general diffusion coefficient theory for multiple-barrier diffusion. Using our diffusion theory and first-principles calculated hopping rates for each barrier, we calculate the diffusion coefficients of Cd, Cu, Te, and Cl interstitials in CdTe for their full multiple-barrier diffusion pathways. As a result, we found that the calculated diffusivity agrees well with the experimental measurement, thus justifying our theory, which is generalmore » for many other systems.« less

Use of Thematic Mapper for water quality assessment

NASA Technical Reports Server (NTRS)

Horn, E. M.; Morrissey, L. A.

1984-01-01

The evaluation of simulated TM data obtained on an ER-2 aircraft at twenty-five predesignated sample sites for mapping water quality factors such as conductivity, pH, suspended solids, turbidity, temperature, and depth, is discussed. Using a multiple regression for the seven TM bands, an equation is developed for the suspended solids. TM bands 1, 2, 3, 4, and 6 are used with logarithm conductivity in a multiple regression. The assessment of regression equations for a high coefficient of determination (R-squared) and statistical significance is considered. Confidence intervals about the mean regression point are calculated in order to assess the robustness of the regressions used for mapping conductivity, turbidity, and suspended solids, and by regressing random subsamples of sites and comparing the resultant range of R-squared, cross validation is conducted.

Effective radiation exposure evaluation during a one year follow-up of urolithiasis patients after extracorporeal shock wave lithotripsy.

PubMed

Kaynar, Mehmet; Tekinarslan, Erdem; Keskin, Suat; Buldu, İbrahim; Sönmez, Mehmet Giray; Karatag, Tuna; Istanbulluoglu, Mustafa Okan

2015-01-01

To determine and evaluate the effective radiation exposure during a one year follow-up of urolithiasis patients following the SWL (extracorporeal shock wave lithotripsy) treatment. Total Effective Radiation Exposure (ERE) doses for each of the 129 patients: 44 kidney stone patients, 41 ureter stone patients, and 44 multiple stone location patients were calculated by adding up the radiation doses of each ionizing radiation session including images (IVU, KUB, CT) throughout a one year follow-up period following the SWL. Total mean ERE values for the kidney stone group was calculated as 15, 91 mSv (5.10-27.60), for the ureter group as 13.32 mSv (5.10-24.70), and in the multiple stone location group as 27.02 mSv (9.41-54.85). There was no statistically significant differences between the kidney and ureter groups in terms of the ERE dose values (p = 0.221) (p >0.05). In the comparison of the kidney and ureter stone groups with the multiple stone location group; however, there was a statistically significant difference (p = 0.000) (p <0.05). ERE doses should be a factor to be considered right at the initiation of any diagnostic and/or therapeutic procedure. Especially in the case of multiple stone locations, due to the high exposure to ionized radiation, different imaging modalities with low dose and/or totally without a dose should be employed in the diagnosis, treatment, and follow-up bearing the aim to optimize diagnosis while minimizing the radiation dose as much as possible.

Determining the nuclear data uncertainty on MONK10 and WIMS10 criticality calculations

NASA Astrophysics Data System (ADS)

Ware, Tim; Dobson, Geoff; Hanlon, David; Hiles, Richard; Mason, Robert; Perry, Ray

2017-09-01

The ANSWERS Software Service is developing a number of techniques to better understand and quantify uncertainty on calculations of the neutron multiplication factor, k-effective, in nuclear fuel and other systems containing fissile material. The uncertainty on the calculated k-effective arises from a number of sources, including nuclear data uncertainties, manufacturing tolerances, modelling approximations and, for Monte Carlo simulation, stochastic uncertainty. For determining the uncertainties due to nuclear data, a set of application libraries have been generated for use with the MONK10 Monte Carlo and the WIMS10 deterministic criticality and reactor physics codes. This paper overviews the generation of these nuclear data libraries by Latin hypercube sampling of JEFF-3.1.2 evaluated data based upon a library of covariance data taken from JEFF, ENDF/B, JENDL and TENDL evaluations. Criticality calculations have been performed with MONK10 and WIMS10 using these sampled libraries for a number of benchmark models of fissile systems. Results are presented which show the uncertainty on k-effective for these systems arising from the uncertainty on the input nuclear data.

The dependence of stellar properties on initial cloud density

NASA Astrophysics Data System (ADS)

Jones, Michael O.; Bate, Matthew R.

2018-05-01

We investigate the dependence of stellar properties on the initial mean density of the molecular cloud in which stellar clusters form using radiation hydrodynamical simulations that resolve the opacity limit for fragmentation. We have simulated the formation of three star clusters from the gravitational collapse of molecular clouds whose densities vary by a factor of a hundred. As with previous calculations including radiative feedback, we find that the dependence of the characteristic stellar mass, Mc, on the initial mean density of the cloud, ρ, is weaker than the dependence of the thermal Jeans mass. However, unlike previous calculations, which found no statistically significant variation in the median mass with density, we find a weak dependence approximately of the form Mc∝ρ-1/5. The distributions of properties of multiple systems do not vary significantly between the calculations. We compare our results to the result of observational surveys of star-forming regions, and suggest that the similarities between the properties of our lowest density calculation and the nearby Taurus-Auriga region indicate that the apparent excess of solar-type stars observed may be due to the region's low density.

Precision gravity studies at Cerro Prieto: a progress report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Grannell, R.B.; Kroll, R.C.; Wyman, R.M.

A third and fourth year of precision gravity data collection and reduction have now been completed at the Cerro Prieto geothermal field. In summary, 66 permanently monumented stations were occupied between December and April of 1979 to 1980 and 1980 to 1981 by a LaCoste and Romberg gravity meter (G300) at least twice, with a minimum of four replicate values obtained each time. Station 20 alternate, a stable base located on Cerro Prieto volcano, was used as the reference base for the third year and all the stations were tied to this base, using four to five hour loops. Themore » field data were reduced to observed gravity values by (1) multiplication with the appropriate calibration factor; (2) removal of calculated tidal effects; (3) calculation of average values at each station, and (4) linear removal of accumulated instrumental drift which remained after carrying out the first three reductions. Following the reduction of values and calculation of gravity differences between individual stations and the base stations, standard deviations were calculated for the averaged occupation values (two to three per station). In addition, pooled variance calculations were carried out to estimate precision for the surveys as a whole.« less

Validation of total skin electron irradiation (TSEI) technique dosimetry data by Monte Carlo simulation

PubMed Central

Borzov, Egor; Daniel, Shahar; Bar‐Deroma, Raquel

2016-01-01

Total skin electron irradiation (TSEI) is a complex technique which requires many nonstandard measurements and dosimetric procedures. The purpose of this work was to validate measured dosimetry data by Monte Carlo (MC) simulations using EGSnrc‐based codes (BEAMnrc and DOSXYZnrc). Our MC simulations consisted of two major steps. In the first step, the incident electron beam parameters (energy spectrum, FWHM, mean angular spread) were adjusted to match the measured data (PDD and profile) at SSD=100 cm for an open field. In the second step, these parameters were used to calculate dose distributions at the treatment distance of 400 cm. MC simulations of dose distributions from single and dual fields at the treatment distance were performed in a water phantom. Dose distribution from the full treatment with six dual fields was simulated in a CT‐based anthropomorphic phantom. MC calculations were compared to the available set of measurements used in clinical practice. For one direct field, MC calculated PDDs agreed within 3%/1 mm with the measurements, and lateral profiles agreed within 3% with the measured data. For the OF, the measured and calculated results were within 2% agreement. The optimal angle of 17° was confirmed for the dual field setup. Dose distribution from the full treatment with six dual fields was simulated in a CT‐based anthropomorphic phantom. The MC‐calculated multiplication factor (B12‐factor), which relates the skin dose for the whole treatment to the dose from one calibration field, for setups with and without degrader was 2.9 and 2.8, respectively. The measured B12‐factor was 2.8 for both setups. The difference between calculated and measured values was within 3.5%. It was found that a degrader provides more homogeneous dose distribution. The measured X‐ray contamination for the full treatment was 0.4%; this is compared to the 0.5% X‐ray contamination obtained with the MC calculation. Feasibility of MC simulation in an anthropomorphic phantom for a full TSEI treatment was proved and is reported for the first time in the literature. The results of our MC calculations were found to be in general agreement with the measurements, providing a promising tool for further studies of dose distribution calculations in TSEI. PACS number(s): 87.10. Rt, 87.55.K, 87.55.ne PMID:27455502

Transverse shear effects on the stress-intensity factor for a circumferentially cracked, specially orthotropic cylindrical shell

NASA Technical Reports Server (NTRS)

Delale, F.; Erdogan, F.

1977-01-01

The problem of a cylindrical shell containing a circumferential through crack is considered by taking into account the effect of transverse shear deformations. The formulation is given for a specially orthotropic material within the confines of a linearized shallow shell theory. The particular theory used permits the consideration of all five boundary conditions regarding moment and stress resultants on the crack surface. Consequently, aside from multiplicative constants representing the stress intensity factors, the membrane and bending components of the asymptotic stress fields near the crack tip are found to be identical. The stress intensity factors are calculated separately for a cylinder under a uniform membrane load, and that under a uniform bending moment. Sample results showing the nature of the out-of-plane crack surface displacement and the effect of the Poisson's ratio are presented.

Design and implementation of the modified signed digit multiplication routine on a ternary optical computer.

PubMed

Xu, Qun; Wang, Xianchao; Xu, Chao

2017-06-01

Multiplication with traditional electronic computers is faced with a low calculating accuracy and a long computation time delay. To overcome these problems, the modified signed digit (MSD) multiplication routine is established based on the MSD system and the carry-free adder. Also, its parallel algorithm and optimization techniques are studied in detail. With the help of a ternary optical computer's characteristics, the structured data processor is designed especially for the multiplication routine. Several ternary optical operators are constructed to perform M transformations and summations in parallel, which has accelerated the iterative process of multiplication. In particular, the routine allocates data bits of the ternary optical processor based on digits of multiplication input, so the accuracy of the calculation results can always satisfy the users. Finally, the routine is verified by simulation experiments, and the results are in full compliance with the expectations. Compared with an electronic computer, the MSD multiplication routine is not only good at dealing with large-value data and high-precision arithmetic, but also maintains lower power consumption and fewer calculating delays.

Identifying localized and scale-specific multivariate controls of soil organic matter variations using multiple wavelet coherence.

PubMed

Zhao, Ruiying; Biswas, Asim; Zhou, Yin; Zhou, Yue; Shi, Zhou; Li, Hongyi

2018-06-23

Environmental factors have shown localized and scale-dependent controls over soil organic matter (SOM) distribution in the landscape. Previous studies have explored the relationships between SOM and individual controlling factors; however, few studies have indicated the combined control from multiple environmental factors. In this study, we compared the localized and scale-dependent univariate and multivariate controls of SOM along two long transects (northeast, NE transect and north, N transect) from China. Bivariate wavelet coherence (BWC) between SOM and individual factors and multiple wavelet coherence (MWC) between SOM and factor combinations were calculated. Average wavelet coherence (AWC) and percent area of significant coherence (PASC) were used to assess the relative dominance of individual and a combination of factors to explain SOM variations at different scales and locations. The results showed that (in BWC analysis) mean annual temperature (MAT) with the largest AWC (0.39) and PASC (16.23%) was the dominant factor in explaining SOM variations along the NE transect. The topographic wetness index (TWI) was the dominant factor (AWC = 0.39 and PASC = 20.80%) along the N transect. MWC identified the combination of Slope, net primary production (NPP) and mean annual precipitation (MAP) as the most important combination in explaining SOM variations along the NE transect with a significant increase in AWC and PASC at different scales and locations (e.g. AWC = 0.91 and PASC = 58.03% at all scales). The combination of TWI, NPP and normalized difference vegetation index (NDVI) was the most influential along the N transect (AWC = 0.83 and PASC = 32.68% at all scales). The results indicated that the combined controls of environmental factors on SOM variations at different scales and locations in a large area can be identified by MWC. This is promising for a better understanding of the multivariate controls in SOM variations at larger spatial scales and may improve the capability of digital soil mapping. Copyright © 2018 Elsevier B.V. All rights reserved.

Borrowing of strength and study weights in multivariate and network meta-analysis.

PubMed

Jackson, Dan; White, Ian R; Price, Malcolm; Copas, John; Riley, Richard D

2017-12-01

Multivariate and network meta-analysis have the potential for the estimated mean of one effect to borrow strength from the data on other effects of interest. The extent of this borrowing of strength is usually assessed informally. We present new mathematical definitions of 'borrowing of strength'. Our main proposal is based on a decomposition of the score statistic, which we show can be interpreted as comparing the precision of estimates from the multivariate and univariate models. Our definition of borrowing of strength therefore emulates the usual informal assessment. We also derive a method for calculating study weights, which we embed into the same framework as our borrowing of strength statistics, so that percentage study weights can accompany the results from multivariate and network meta-analyses as they do in conventional univariate meta-analyses. Our proposals are illustrated using three meta-analyses involving correlated effects for multiple outcomes, multiple risk factor associations and multiple treatments (network meta-analysis).

Borrowing of strength and study weights in multivariate and network meta-analysis

PubMed Central

Jackson, Dan; White, Ian R; Price, Malcolm; Copas, John; Riley, Richard D

2016-01-01

Multivariate and network meta-analysis have the potential for the estimated mean of one effect to borrow strength from the data on other effects of interest. The extent of this borrowing of strength is usually assessed informally. We present new mathematical definitions of ‘borrowing of strength’. Our main proposal is based on a decomposition of the score statistic, which we show can be interpreted as comparing the precision of estimates from the multivariate and univariate models. Our definition of borrowing of strength therefore emulates the usual informal assessment. We also derive a method for calculating study weights, which we embed into the same framework as our borrowing of strength statistics, so that percentage study weights can accompany the results from multivariate and network meta-analyses as they do in conventional univariate meta-analyses. Our proposals are illustrated using three meta-analyses involving correlated effects for multiple outcomes, multiple risk factor associations and multiple treatments (network meta-analysis). PMID:26546254

Multivariate meta-analysis using individual participant data

PubMed Central

Riley, R. D.; Price, M. J.; Jackson, D.; Wardle, M.; Gueyffier, F.; Wang, J.; Staessen, J. A.; White, I. R.

2016-01-01

When combining results across related studies, a multivariate meta-analysis allows the joint synthesis of correlated effect estimates from multiple outcomes. Joint synthesis can improve efficiency over separate univariate syntheses, may reduce selective outcome reporting biases, and enables joint inferences across the outcomes. A common issue is that within-study correlations needed to fit the multivariate model are unknown from published reports. However, provision of individual participant data (IPD) allows them to be calculated directly. Here, we illustrate how to use IPD to estimate within-study correlations, using a joint linear regression for multiple continuous outcomes and bootstrapping methods for binary, survival and mixed outcomes. In a meta-analysis of 10 hypertension trials, we then show how these methods enable multivariate meta-analysis to address novel clinical questions about continuous, survival and binary outcomes; treatment–covariate interactions; adjusted risk/prognostic factor effects; longitudinal data; prognostic and multiparameter models; and multiple treatment comparisons. Both frequentist and Bayesian approaches are applied, with example software code provided to derive within-study correlations and to fit the models. PMID:26099484

Minimum emittance in TBA and MBA lattices

NASA Astrophysics Data System (ADS)

Xu, Gang; Peng, Yue-Mei

2015-03-01

For reaching a small emittance in a modern light source, triple bend achromats (TBA), theoretical minimum emittance (TME) and even multiple bend achromats (MBA) have been considered. This paper derived the necessary condition for achieving minimum emittance in TBA and MBA theoretically, where the bending angle of inner dipoles has a factor of 31/3 bigger than that of the outer dipoles. Here, we also calculated the conditions attaining the minimum emittance of TBA related to phase advance in some special cases with a pure mathematics method. These results may give some directions on lattice design.

Simulation and analysis of main steam control system based on heat transfer calculation

NASA Astrophysics Data System (ADS)

Huang, Zhenqun; Li, Ruyan; Feng, Zhongbao; Wang, Songhan; Li, Wenbo; Cheng, Jiwei; Jin, Yingai

2018-05-01

In this paper, after thermal power plant 300MW boiler was studied, mat lab was used to write calculation program about heat transfer process between the main steam and boiler flue gas and amount of water was calculated to ensure the main steam temperature keeping in target temperature. Then heat transfer calculation program was introduced into Simulink simulation platform based on control system multiple models switching and heat transfer calculation. The results show that multiple models switching control system based on heat transfer calculation not only overcome the large inertia of main stream temperature, a large hysteresis characteristic of main stream temperature, but also adapted to the boiler load changing.

A case study of multi-seam coal mine entry stability analysis with strength reduction method

PubMed Central

Tulu, Ihsan Berk; Esterhuizen, Gabriel S; Klemetti, Ted; Murphy, Michael M.; Sumner, James; Sloan, Michael

2017-01-01

In this paper, the advantage of using numerical models with the strength reduction method (SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated. A coal mine under variable topography from the Central Appalachian region is used as a case study. At this mine, unexpected roof conditions were encountered during development below previously mined panels. Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-and-pillar panels. Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries. The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations. The SRM-calculated stability factors were compared with observations made during the site visits, and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case. It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines. PMID:28239503

A case study of multi-seam coal mine entry stability analysis with strength reduction method.

PubMed

Tulu, Ihsan Berk; Esterhuizen, Gabriel S; Klemetti, Ted; Murphy, Michael M; Sumner, James; Sloan, Michael

2016-03-01

In this paper, the advantage of using numerical models with the strength reduction method (SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated. A coal mine under variable topography from the Central Appalachian region is used as a case study. At this mine, unexpected roof conditions were encountered during development below previously mined panels. Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-and-pillar panels. Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries. The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations. The SRM-calculated stability factors were compared with observations made during the site visits, and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case. It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.

Molybdenum-99 production calculation analysis of SAMOP reactor based on thorium nitrate fuel

NASA Astrophysics Data System (ADS)

Syarip; Togatorop, E.; Yassar

2018-03-01

SAMOP (Subcritical Assembly for Molybdenum-99 Production) has the potential to use thorium as fuel to produce 99Mo after modifying the design, but the production performance has not been discovered yet. A study needs to be done to obtain the correlation between 99Mo production with the mixed fuel composition of uranium and with SAMOP power on the modified SAMOP design. The study aims to obtain the production of 99Mo based thorium nitrate fuel on SAMOP’s modified designs. Monte Carlo N-Particle eXtended (MCNPX) is required to simulate the operation of the assembly by varying the composition of the uranium-thorium nitrate mixed fuel, geometry and power fraction on the SAMOP modified designs. The burnup command on the MCNPX is used to confirm the 99Mo production result. The assembly is simulated to operate for 6 days with subcritical neutron multiplication factor (keff = 0.97-0.99). The neutron multiplication factor of the modified design (keff) is 0.97, the activity obtained from 99Mo is 18.58 Ci at 1 kW power operation.

Computer-aided molecular modeling techniques for predicting the stability of drug cyclodextrin inclusion complexes in aqueous solutions

NASA Astrophysics Data System (ADS)

Faucci, Maria Teresa; Melani, Fabrizio; Mura, Paola

2002-06-01

Molecular modeling was used to investigate factors influencing complex formation between cyclodextrins and guest molecules and predict their stability through a theoretical model based on the search for a correlation between experimental stability constants ( Ks) and some theoretical parameters describing complexation (docking energy, host-guest contact surfaces, intermolecular interaction fields) calculated from complex structures at a minimum conformational energy, obtained through stochastic methods based on molecular dynamic simulations. Naproxen, ibuprofen, ketoprofen and ibuproxam were used as model drug molecules. Multiple Regression Analysis allowed identification of the significant factors for the complex stability. A mathematical model ( r=0.897) related log Ks with complex docking energy and lipophilic molecular fields of cyclodextrin and drug.

Age- and Sex-Specific Reference Values for Media/Lumen Ratio in Small Arteries and Relationship With Risk Factors.

PubMed

Bruno, Rosa Maria; Grassi, Guido; Seravalle, Gino; Savoia, Carmine; Rizzoni, Damiano; Virdis, Agostino

2018-04-23

Small-artery remodeling is an early feature of target organ damage in hypertension and retains a negative prognostic value. The aim of the study is to establish age- and sex-specific reference values for media/lumen in small arteries obtained in humans by biopsy. Data from 91 healthy individuals and 200 individuals with cardiovascular risk factors in primary prevention from 4 Italian centers were pooled. Sex-specific equations for media/lumen in the healthy subpopulation, with age as dependent variable, were calculated. These equations were used to calculate predicted media/lumen values in individuals with risk factors and Z scores. The association between classical risk factors and Z scores was then explored by multiple regression analysis. A second-degree polynomial equation model was chosen to obtain sex-specific equations for media/lumen, with age as dependent variable. In the population with risk factors (111 men, age 50.5±14.0 years, hypertension 80.5%), media/lumen Z scores were independently associated with body mass index (standardized β=0.293, P =0.0001), total cholesterol (β=0.191, P =0.031), current smoking (β=0.238, P =0.0005), fasting blood glucose (β=0.204, P =0.003), systolic blood pressure (β=0.233, P =0.023), and female sex (β=0.799, P =0.038). A significant interaction between female sex and total cholesterol was found (β=-0.979, P =0.014). Results were substantially similar in the hypertensive subgroup. A method to calculate individual values of remodeling and growth index based on reference values was also presented. Age- and sex-specific percentiles of media/lumen in a healthy population were estimated. In a predominantly hypertensive population, media/lumen Z scores were associated with major cardiovascular risk factors, including body mass index, cholesterol, smoking, glucose, and systolic blood pressure. Significant sex differences were observed. © 2018 American Heart Association, Inc.

Relativistic scattered wave calculations on UF6

NASA Technical Reports Server (NTRS)

Case, D. A.; Yang, C. Y.

1980-01-01

Self-consistent Dirac-Slater multiple scattering calculations are presented for UF6. The results are compared critically to other relativistic calculations, showing that the results of all molecular orbital calculations are in qualitative agreement, as measured by energy levels, population analyses, and spin-orbit splittings. A detailed comparison is made to the relativistic X alpha(RX alpha) method of Wood and Boring, which also uses multiple scattering theory, but incorporates relativistic effects in a more approximate fashion. For the most part, the RX alpha results are in agreement with the present results.

Factors affecting the accuracy of near-infrared spectroscopy concentration calculations for focal changes in oxygenation parameters

NASA Technical Reports Server (NTRS)

Strangman, Gary; Franceschini, Maria Angela; Boas, David A.; Sutton, J. P. (Principal Investigator)

2003-01-01

Near-infrared spectroscopy (NIRS) can be used to noninvasively measure changes in the concentrations of oxy- and deoxyhemoglobin in tissue. We have previously shown that while global changes can be reliably measured, focal changes can produce erroneous estimates of concentration changes (NeuroImage 13 (2001), 76). Here, we describe four separate sources for systematic error in the calculation of focal hemoglobin changes from NIRS data and use experimental methods and Monte Carlo simulations to examine the importance and mitigation methods of each. The sources of error are: (1). the absolute magnitudes and relative differences in pathlength factors as a function of wavelength, (2). the location and spatial extent of the absorption change with respect to the optical probe, (3). possible differences in the spatial distribution of hemoglobin species, and (4). the potential for simultaneous monitoring of multiple regions of activation. We found wavelength selection and optode placement to be important variables in minimizing such errors, and our findings indicate that appropriate experimental procedures could reduce each of these errors to a small fraction (<10%) of the observed concentration changes.

Pathways to fraction learning: Numerical abilities mediate the relation between early cognitive competencies and later fraction knowledge.

PubMed

Ye, Ai; Resnick, Ilyse; Hansen, Nicole; Rodrigues, Jessica; Rinne, Luke; Jordan, Nancy C

2016-12-01

The current study investigated the mediating role of number-related skills in the developmental relationship between early cognitive competencies and later fraction knowledge using structural equation modeling. Fifth-grade numerical skills (i.e., whole number line estimation, non-symbolic proportional reasoning, multiplication, and long division skills) mapped onto two distinct factors: magnitude reasoning and calculation. Controlling for participants' (N=536) demographic characteristics, these two factors fully mediated relationships between third-grade general cognitive competencies (attentive behavior, verbal and nonverbal intellectual abilities, and working memory) and sixth-grade fraction knowledge (concepts and procedures combined). However, specific developmental pathways differed by type of fraction knowledge. Magnitude reasoning ability fully mediated paths from all four cognitive competencies to knowledge of fraction concepts, whereas calculation ability fully mediated paths from attentive behavior and verbal ability to knowledge of fraction procedures (all with medium to large effect sizes). These findings suggest that there are partly overlapping, yet distinct, developmental pathways from cognitive competencies to general fraction knowledge, fraction concepts, and fraction procedures. Copyright © 2016 Elsevier Inc. All rights reserved.

Study of hadron bundles observed in Chacaltaya two-story emulsion chamber

NASA Technical Reports Server (NTRS)

Aoki, H.

1985-01-01

The existence of hadron-rich families associated with few gamma-ray emission named Centauro and Mini-Centauro phemonena was reported. It was investigated whether these are produced by the special type of interaction different from the ordinary pion multiple production or not. The experimental results are compared with simulation calculation based on ordinary multiple pion production model. Both hadron multiplicity distribution, obtained from the present observation and the simulation calculation, show almost the same distribution which means that hadron bundles of such smaller multiplicities are considered to originate from successive interactions of surviving nucleon with the nature of multiple production during passage through the atmosphere.

Association of Dentine Hypersensitivity with Different Risk Factors – A Cross Sectional Study

PubMed Central

Vijaya, V; Sanjay, Venkataraam; Varghese, Rana K; Ravuri, Rajyalakshmi; Agarwal, Anil

2013-01-01

Background: This study was done to assess the prevalence of Dentine hypersensitivity (DH) and its associated risk factors. Materials & Methods: This epidemiological study was done among patients coming to dental college regarding prevalence of DH. A self structured questionnaire along with clinical examination was done for assessment. Descriptive statistics were obtained and frequency distribution was calculated using Chi square test at p value <0.05. Stepwise multiple linear regression was also done to access frequency of DH with different factors. Results: The study population was comprised of 655 participants with different age groups. Our study showed prevalence as 55% and it was more common among males. Similarly smokers and those who use hard tooth brush had more cases of DH. Step wise multiple linear regression showed that best predictor for DH was age followed by habit of smoking and type of tooth brush. Most aggravating factors were cold water (15.4%) and sweet foods (14.7%), whereas only 5% of the patients had it while brushing. Conclusion: A high level of dental hypersensitivity has been in this study and more common among males. A linear finding was shown with age, smoking and type of tooth brush. How to cite this article: Vijaya V, Sanjay V, Varghese RK, Ravuri R, Agarwal A. Association of Dentine Hypersensitivity with Different Risk Factors – A Cross Sectional Study. J Int Oral Health 2013;5(6):88-92 . PMID:24453451

Nuclear modification factor in an anisotropic quark-gluon plasma

NASA Astrophysics Data System (ADS)

Mandal, Mahatsab; Bhattacharya, Lusaka; Roy, Pradip

2011-10-01

We calculate the nuclear modification factor (RAA) of light hadrons by taking into account the initial state momentum anisotropy of the quark-gluon plasma (QGP) expected to be formed in relativistic heavy ion collisions. Such an anisotropy can result from the initial rapid longitudinal expansion of the matter. A phenomenological model for the space-time evolution of the anisotropic QGP is used to obtain the time dependence of the anisotropy parameter ξ and the hard momentum scale, phard. The result is then compared with the PHENIX experimental data to constrain the isotropization time scale, τiso for fixed initial conditions (FIC). It is shown that the extracted value of τiso lies in the range 0.5⩽τiso⩽1.5. However, using a fixed final multiplicity (FFM) condition does not lead to any firm conclusion about the extraction of the isotropization time. The present calculation is also extended to contrast with the recent measurement of nuclear modification factor by the ALICE collaboration at s=2.76 TeV. It is argued that in the present approach, the extraction of τiso at this energy is uncertain and, therefore, refinement of the model is necessary. The sensitivity of the results on the initial conditions has been discussed. We also present the nuclear modification factor at Large Hadron Collider (LHC) energies with s=5.5 TeV.

Use of biopartitioning micellar chromatography and RP-HPLC for the determination of blood-brain barrier penetration of α-adrenergic/imidazoline receptor ligands, and QSPR analysis.

PubMed

Vucicevic, J; Popovic, M; Nikolic, K; Filipic, S; Obradovic, D; Agbaba, D

2017-03-01

For this study, 31 compounds, including 16 imidazoline/α-adrenergic receptor (IRs/α-ARs) ligands and 15 central nervous system (CNS) drugs, were characterized in terms of the retention factors (k) obtained using biopartitioning micellar and classical reversed phase chromatography (log k BMC and log k wRP , respectively). Based on the retention factor (log k wRP ) and slope of the linear curve (S) the isocratic parameter (φ 0 ) was calculated. Obtained retention factors were correlated with experimental log BB values for the group of examined compounds. High correlations were obtained between logarithm of biopartitioning micellar chromatography (BMC) retention factor and effective permeability (r(log k BMC /log BB): 0.77), while for RP-HPLC system the correlations were lower (r(log k wRP /log BB): 0.58; r(S/log BB): -0.50; r(φ 0 /P e ): 0.61). Based on the log k BMC retention data and calculated molecular parameters of the examined compounds, quantitative structure-permeability relationship (QSPR) models were developed using partial least squares, stepwise multiple linear regression, support vector machine and artificial neural network methodologies. A high degree of structural diversity of the analysed IRs/α-ARs ligands and CNS drugs provides wide applicability domain of the QSPR models for estimation of blood-brain barrier penetration of the related compounds.

Application of back propagation artificial neural network on genetic variants in adiponectin ADIPOQ, peroxisome proliferator-activated receptor-γ, and retinoid X receptor-α genes and type 2 diabetes risk in a Chinese Han population.

PubMed

Shi, Hui; Lu, Ying; Du, Juan; Du, Wencong; Ye, Xinhua; Yu, Xiaofang; Ma, Jianhua; Cheng, Jinluo; Gao, Yanqin; Cao, Yuanyuan; Zhou, Ling; Li, Qian

2012-03-01

Our study was designed to explore the applied characteristics of the back propagation artificial neural network (BPANN) on studying the genetic variants in adipnectin ADIPOQ, peroxisome proliferator-activated receptor (PPAR)-γ, and retinoid X receptor-α (RXR-α) genes and type 2 diabetes mellitus (T2DM) risks in a Chinese Han population. We used BPANN as the fitting model based on data gathered from T2DM patients (n=913) and normal controls (n=1,001). The mean impact value (MIV) for each input variables were calculated, and the sequence of the factors according to their absolute MIVs was sorted. The results from BPANN were compared with multiple logistic regression analysis, and the generalized multifactor dimensionality reduction (GMDR) method was used to calculate the joint effects of ADIPOQ, PPAR-γ, and RXR-α genes. By BPANN analysis, the sequence according to the importance of the T2DM risk factors was in the order of serum adiponectin level, rs3856806, rs7649121, hypertension, rs3821799, rs17827276, rs12495941, rs4240711, age, rs16861194, waist circumference, rs2241767, rs2920502, rs1063539, alcohol drinking, smoking, hyperlipoproteinemia, gender, rs3132291, T2DM family history, rs4842194, rs822394, rs1801282, rs1045570, rs16861205, rs6537944, body mass index, rs266729, and rs1801282. However, compared with multiple logistic regression analysis, only 11 factors were statistically significant. After overweight and obesity were taken as environment adjustment factors into the analysis, model A2 B4 C5 C6 C8 (rs3856806, rs4240711, rs7649121, rs3821799, rs12495941) was the best model (coefficient of variation consistency=10/10, P=0.0107) in the GMDR method. These results suggested the interactions of ADIPOQ, PPAR-γ, and RXR-α genes might play a role in susceptibility to T2DM. BPANN could be used to analyze the risk factors of diseases and provide more complicated relationships between inputs and outputs.

Absolute binding free energies between T4 lysozyme and 141 small molecules: calculations based on multiple rigid receptor configurations

PubMed Central

Xie, Bing; Nguyen, Trung Hai; Minh, David D. L.

2017-01-01

We demonstrate the feasibility of estimating protein-ligand binding free energies using multiple rigid receptor configurations. Based on T4 lysozyme snapshots extracted from six alchemical binding free energy calculations with a flexible receptor, binding free energies were estimated for a total of 141 ligands. For 24 ligands, the calculations reproduced flexible-receptor estimates with a correlation coefficient of 0.90 and a root mean square error of 1.59 kcal/mol. The accuracy of calculations based on Poisson-Boltzmann/Surface Area implicit solvent was comparable to previously reported free energy calculations. PMID:28430432

The concerted calculation of the BN-600 reactor for the deterministic and stochastic codes

NASA Astrophysics Data System (ADS)

Bogdanova, E. V.; Kuznetsov, A. N.

2017-01-01

The solution of the problem of increasing the safety of nuclear power plants implies the existence of complete and reliable information about the processes occurring in the core of a working reactor. Nowadays the Monte-Carlo method is the most general-purpose method used to calculate the neutron-physical characteristic of the reactor. But it is characterized by large time of calculation. Therefore, it may be useful to carry out coupled calculations with stochastic and deterministic codes. This article presents the results of research for possibility of combining stochastic and deterministic algorithms in calculation the reactor BN-600. This is only one part of the work, which was carried out in the framework of the graduation project at the NRC “Kurchatov Institute” in cooperation with S. S. Gorodkov and M. A. Kalugin. It is considering the 2-D layer of the BN-600 reactor core from the international benchmark test, published in the report IAEA-TECDOC-1623. Calculations of the reactor were performed with MCU code and then with a standard operative diffusion algorithm with constants taken from the Monte - Carlo computation. Macro cross-section, diffusion coefficients, the effective multiplication factor and the distribution of neutron flux and power were obtained in 15 energy groups. The reasonable agreement between stochastic and deterministic calculations of the BN-600 is observed.

Season of infectious mononucleosis as a risk factor for multiple sclerosis: A UK primary care case-control study.

PubMed

Downham, Christina; Visser, Elizabeth; Vickers, Mark; Counsell, Carl

2017-10-01

Infectious mononucleosis (IM) and vitamin D deficiency are both risk factors for multiple sclerosis (MS). We wished to establish if IM in the winter months when vitamin D levels are low may be a greater risk factor for MS than IM in the summer months. We identified all patients with MS diagnosed aged 16-60 in a large primary care database in the United Kingdom and matched each by age, sex, general practice and observation period with up to six controls. We identified a coded diagnosis of IM prior to the index date (date of diagnosis). Logistic regression was used to calculate the odds ratio for prior IM exposure in cases versus controls and for winter versus summer exposure in cases and controls with prior IM exposure. Based on 9247 cases and 55,033 matched controls (246 and 846 with prior IM respectively), IM was associated with the development of MS (OR 1.77, 95%CI 1.53-2.05) but there was no evidence that IM in the winter as opposed to summer was associated with developing MS (OR 1.09, 95%CI 0.72-1.66). We found no evidence that the season of IM influences the risk of subsequent MS. Copyright © 2017 Elsevier B.V. All rights reserved.

A systematic review of SNAPO (Smoking, Nutrition, Alcohol, Physical activity and Obesity) randomized controlled trials in young adult men.

PubMed

Ashton, Lee M; Morgan, Philip J; Hutchesson, Melinda J; Rollo, Megan E; Young, Myles D; Collins, Clare E

2015-12-01

To investigate the effectiveness of Smoking, Nutrition, Alcohol, Physical activity and Obesity (SNAPO) interventions in young men exclusively. The secondary aim was to evaluate the recruitment, retention and engagement strategies. A search with no date restrictions was conducted across seven databases. Randomized controlled trials recruiting young men only (aged 18-35 years) into interventions targeting any SNAPO risk factors were included. Ten studies were included (two nutrition, six alcohol use, two targeting multiple SNAPO risk factors). Six studies (two nutrition, three alcohol use and one targeting multiple SNAPO risk factors) demonstrated significant positive short-term intervention effects, but impact was either not assessed beyond the intervention (n=3), had short-term follow-up (≤6 months) (n=2) or not sustained beyond six months (n=1). Overall, a high risk of bias was identified across studies. Only one study undertook a power calculation and recruited the required sample size. Adequate retention was achieved in three studies. Effectiveness of engagement strategies was not reported in any studies. Despite preliminary evidence of short-term effectiveness of SNAPO interventions in young men, few studies characterized by a high risk of bias were identified. High quality SNAPO interventions for young men are warranted. Copyright © 2015 Elsevier Inc. All rights reserved.

Hypergraph partitioning implementation for parallelizing matrix-vector multiplication using CUDA GPU-based parallel computing

NASA Astrophysics Data System (ADS)

Murni, Bustamam, A.; Ernastuti, Handhika, T.; Kerami, D.

2017-07-01

Calculation of the matrix-vector multiplication in the real-world problems often involves large matrix with arbitrary size. Therefore, parallelization is needed to speed up the calculation process that usually takes a long time. Graph partitioning techniques that have been discussed in the previous studies cannot be used to complete the parallelized calculation of matrix-vector multiplication with arbitrary size. This is due to the assumption of graph partitioning techniques that can only solve the square and symmetric matrix. Hypergraph partitioning techniques will overcome the shortcomings of the graph partitioning technique. This paper addresses the efficient parallelization of matrix-vector multiplication through hypergraph partitioning techniques using CUDA GPU-based parallel computing. CUDA (compute unified device architecture) is a parallel computing platform and programming model that was created by NVIDIA and implemented by the GPU (graphics processing unit).

Dual-Level Method for Estimating Multistructural Partition Functions with Torsional Anharmonicity.

PubMed

Bao, Junwei Lucas; Xing, Lili; Truhlar, Donald G

2017-06-13

For molecules with multiple torsions, an accurate evaluation of the molecular partition function requires consideration of multiple structures and their torsional-potential anharmonicity. We previously developed a method called MS-T for this problem, and it requires an exhaustive conformational search with frequency calculations for all the distinguishable conformers; this can become expensive for molecules with a large number of torsions (and hence a large number of structures) if it is carried out with high-level methods. In the present work, we propose a cost-effective method to approximate the MS-T partition function when there are a large number of structures, and we test it on a transition state that has eight torsions. This new method is a dual-level method that combines an exhaustive conformer search carried out by a low-level electronic structure method (for instance, AM1, which is very inexpensive) and selected calculations with a higher-level electronic structure method (for example, density functional theory with a functional that is suitable for conformational analysis and thermochemistry). To provide a severe test of the new method, we consider a transition state structure that has 8 torsional degrees of freedom; this transition state structure is formed along one of the reaction pathways of the hydrogen abstraction reaction (at carbon-1) of ketohydroperoxide (KHP; its IUPAC name is 4-hydroperoxy-2-pentanone) by OH radical. We find that our proposed dual-level method is able to significantly reduce the computational cost for computing MS-T partition functions for this test case with a large number of torsions and with a large number of conformers because we carry out high-level calculations for only a fraction of the distinguishable conformers found by the low-level method. In the example studied here, the dual-level method with 40 high-level optimizations (1.8% of the number of optimizations in a coarse-grained full search and 0.13% of the number of optimizations in a fine-grained full search) reproduces the full calculation of the high-level partition function within a factor of 1.0 to 2.0 from 200 to 1000 K. The error in the dual-level method can be further reduced to factors of 0.6 to 1.1 over the whole temperature interval from 200 to 2400 K by optimizing 128 structures (5.9% of the number of optimizations in a fine-grained full search and 0.41% of the number of optimizations in a fine-grained full search). These factor-of-two or better errors are small compared to errors up to a factor of 1.0 × 10 3 if one neglects multistructural effects for the case under study.

Suppression of high pT hadrons in Pb + Pb collisions at \\sqrt{s} = 2.76 TeV

NASA Astrophysics Data System (ADS)

Zhang, Hanzhong; Chen, Xiao-Fang; Hirano, Tetsufumi; Wang, Enke; Wang, Xin-Nian

2011-12-01

The nuclear modification factor RAA(pT) for large pT hadrons in central Pb + Pb collisions at \\sqrt{s}=2.76 TeV/n is calculated within the next-to-leading order perturbative QCD parton model with medium-modified fragmentation functions and agree well with the new data. The jet transport parameter that controls medium modification is assumed to be proportional to the initial parton density and the coefficient is fixed by the RHIC data. The charged hadron multiplicity dNch/dη = 1584 ± 80 in central Pb + Pb collisions from the ALICE experiment at the LHC is used to determine both the jet transport parameter and the initial condition for (3+1)D ideal hydrodynamic evolution of the bulk matter that is employed for the calculation of RAA(pT).

Conceptual Core Analysis of Long Life PWR Utilizing Thorium-Uranium Fuel Cycle

NASA Astrophysics Data System (ADS)

Rouf; Su'ud, Zaki

2016-08-01

Conceptual core analysis of long life PWR utilizing thorium-uranium based fuel has conducted. The purpose of this study is to evaluate neutronic behavior of reactor core using combined thorium and enriched uranium fuel. Based on this fuel composition, reactor core have higher conversion ratio rather than conventional fuel which could give longer operation length. This simulation performed using SRAC Code System based on library SRACLIB-JDL32. The calculation carried out for (Th-U)O2 and (Th-U)C fuel with uranium composition 30 - 40% and gadolinium (Gd2O3) as burnable poison 0,0125%. The fuel composition adjusted to obtain burn up length 10 - 15 years under thermal power 600 - 1000 MWt. The key properties such as uranium enrichment, fuel volume fraction, percentage of uranium are evaluated. Core calculation on this study adopted R-Z geometry divided by 3 region, each region have different uranium enrichment. The result show multiplication factor every burn up step for 15 years operation length, power distribution behavior, power peaking factor, and conversion ratio. The optimum core design achieved when thermal power 600 MWt, percentage of uranium 35%, U-235 enrichment 11 - 13%, with 14 years operation length, axial and radial power peaking factor about 1.5 and 1.2 respectively.

Multi -risk assessment at a national level in Georgia

NASA Astrophysics Data System (ADS)

Tsereteli, Nino; Varazanashvili, Otar; Amiranashvili, Avtandil; Tsereteli, Emili; Elizbarashvili, Elizbar; Saluqvadze, Manana; Dolodze, Jemal

2013-04-01

Work presented here was initiated by national GNSF project " Reducing natural disasters multiple risk: a positive factor for Georgia development " and two international projects: NATO SFP 983038 "Seismic hazard and Rusk assessment for Southern Caucasus-eastern Turkey Energy Corridors" and EMME " Earthquake Model for Middle east Region". Methodology for estimation of "general" vulnerability, hazards and multiple risk to natural hazards (namely, earthquakes, landslides, snow avalanches, flash floods, mudflows, drought, hurricanes, frost, hail) where developed for Georgia. The electronic detailed databases of natural disasters were created. These databases contain the parameters of hazardous phenomena that caused natural disasters. The magnitude and intensity scale of the mentioned disasters are reviewed and the new magnitude and intensity scales are suggested for disasters for which the corresponding formalization is not yet performed. The associated economic losses were evaluated and presented in monetary terms for these hazards. Based on the hazard inventory, an approach was developed that allowed for the calculation of an overall vulnerability value for each individual hazard type, using the Gross Domestic Product per unit area (applied to population) as the indicator for elements at risk exposed. The correlation between estimated economic losses, physical exposure and the magnitude for each of the six types of hazards has been investigated in detail by using multiple linear regression analysis. Economic losses for all past events and historical vulnerability were estimated. Finally, the spatial distribution of general vulnerability was assessed, and the expected maximum economic loss was calculated as well as a multi-risk map was set-up.

A Multiplicative Cascade Model for High-Resolution Space-Time Downscaling of Rainfall

NASA Astrophysics Data System (ADS)

Raut, Bhupendra A.; Seed, Alan W.; Reeder, Michael J.; Jakob, Christian

2018-02-01

Distributions of rainfall with the time and space resolutions of minutes and kilometers, respectively, are often needed to drive the hydrological models used in a range of engineering, environmental, and urban design applications. The work described here is the first step in constructing a model capable of downscaling rainfall to scales of minutes and kilometers from time and space resolutions of several hours and a hundred kilometers. A multiplicative random cascade model known as the Short-Term Ensemble Prediction System is run with parameters from the radar observations at Melbourne (Australia). The orographic effects are added through multiplicative correction factor after the model is run. In the first set of model calculations, 112 significant rain events over Melbourne are simulated 100 times. Because of the stochastic nature of the cascade model, the simulations represent 100 possible realizations of the same rain event. The cascade model produces realistic spatial and temporal patterns of rainfall at 6 min and 1 km resolution (the resolution of the radar data), the statistical properties of which are in close agreement with observation. In the second set of calculations, the cascade model is run continuously for all days from January 2008 to August 2015 and the rainfall accumulations are compared at 12 locations in the greater Melbourne area. The statistical properties of the observations lie with envelope of the 100 ensemble members. The model successfully reproduces the frequency distribution of the 6 min rainfall intensities, storm durations, interarrival times, and autocorrelation function.

Identification of Risk Factors for Intravenous Infiltration among Hospitalized Children: A Retrospective Study

PubMed Central

2016-01-01

This retrospective study was aimed to identify risk factors of intravenous (IV) infiltration for hospitalized children. The participants were 1,174 children admitted to a general hospital, who received peripheral intravenous injection therapy at least once, and had complete records. Data were analyzed with frequency and percentage or mean and standard deviation were calculated, and odds ratio (OR) from univariate and multiple logistic regressions. The number and % of infiltrations were 92 and 7.8%, respectively. IV infiltration risk factors were lower limb (OR = 1.72), phenytoin (OR = 11.03), 10% dextrose (OR = 6.55), steroids (OR = 6.21), vancomycin (OR = 4.10), high-concentration electrolytes (OR = 3.49), and ampicillin/sulbactam combination (OR = 3.37). Nurses working at children’s hospitals should consider the risk of IV infiltration for children receiving IV infusion therapy and make a preventive effort to identify IV infiltration in high-risk children at an early stage. PMID:27351488

Source apportionment of trace metals in surface waters of a polluted stream using multivariate statistical analyses.

PubMed

Pekey, Hakan; Karakaş, Duran; Bakoğlu, Mithat

2004-11-01

Surface water samples were collected from ten previously selected sites of the polluted Dil Deresi stream, during two field surveys, December 2001 and April 2002. All samples were analyzed using ICP-AES, and the concentrations of trace metals (Al, As, Ba, Cd, Co, Cr, Cu, Fe, Pb, Sn and Zn) were determined. The results were compared with national and international water quality guidelines, as well as literature values reported for similar rivers. Factor analysis (FA) and a factor analysis-multiple regression (FA-MR) model were used for source apportionment and estimation of contributions from identified sources to the concentration of each parameter. By a varimax rotated factor analysis, four source types were identified as the paint industry; sewage, crustal and road traffic runoff for trace metals, explaining about 83% of the total variance. FA-MR results showed that predicted concentrations were calculated with uncertainties lower than 15%.

Effective radiation exposure evaluation during a one year follow-up of urolithiasis patients after extracorporeal shock wave lithotripsy

PubMed Central

Tekinarslan, Erdem; Keskin, Suat; Buldu, İbrahim; Sönmez, Mehmet Giray; Karatag, Tuna; Istanbulluoglu, Mustafa Okan

2015-01-01

Introduction To determine and evaluate the effective radiation exposure during a one year follow-up of urolithiasis patients following the SWL (extracorporeal shock wave lithotripsy) treatment. Material and methods Total Effective Radiation Exposure (ERE) doses for each of the 129 patients: 44 kidney stone patients, 41 ureter stone patients, and 44 multiple stone location patients were calculated by adding up the radiation doses of each ionizing radiation session including images (IVU, KUB, CT) throughout a one year follow-up period following the SWL. Results Total mean ERE values for the kidney stone group was calculated as 15, 91 mSv (5.10-27.60), for the ureter group as 13.32 mSv (5.10-24.70), and in the multiple stone location group as 27.02 mSv (9.41-54.85). There was no statistically significant differences between the kidney and ureter groups in terms of the ERE dose values (p = 0.221) (p >0.05). In the comparison of the kidney and ureter stone groups with the multiple stone location group; however, there was a statistically significant difference (p = 0.000) (p <0.05). Conclusions ERE doses should be a factor to be considered right at the initiation of any diagnostic and/or therapeutic procedure. Especially in the case of multiple stone locations, due to the high exposure to ionized radiation, different imaging modalities with low dose and/or totally without a dose should be employed in the diagnosis, treatment, and follow-up bearing the aim to optimize diagnosis while minimizing the radiation dose as much as possible. PMID:26568880

Radiation Transport of Heliospheric Lyman-alpha from Combined Cassini and Voyager Data Sets

NASA Technical Reports Server (NTRS)

Pryor, W.; Gangopadhyay, P.; Sandel, B.; Forrester, T.; Quemerais, E.; Moebius, E.; Esposito, L.; Stewart, I.; McClintock, W.; Jouchoux, A.;

Factorization in large-scale many-body calculations

DOE PAGES

Johnson, Calvin W.; Ormand, W. Erich; Krastev, Plamen G.

2013-08-07

One approach for solving interacting many-fermion systems is the configuration-interaction method, also sometimes called the interacting shell model, where one finds eigenvalues of the Hamiltonian in a many-body basis of Slater determinants (antisymmetrized products of single-particle wavefunctions). The resulting Hamiltonian matrix is typically very sparse, but for large systems the nonzero matrix elements can nonetheless require terabytes or more of storage. An alternate algorithm, applicable to a broad class of systems with symmetry, in our case rotational invariance, is to exactly factorize both the basis and the interaction using additive/multiplicative quantum numbers; such an algorithm recreates the many-body matrix elementsmore » on the fly and can reduce the storage requirements by an order of magnitude or more. Here, we discuss factorization in general and introduce a novel, generalized factorization method, essentially a ‘double-factorization’ which speeds up basis generation and set-up of required arrays. Although we emphasize techniques, we also place factorization in the context of a specific (unpublished) configuration-interaction code, BIGSTICK, which runs both on serial and parallel machines, and discuss the savings in memory due to factorization.« less

MrGrid: A Portable Grid Based Molecular Replacement Pipeline

PubMed Central

Reboul, Cyril F.; Androulakis, Steve G.; Phan, Jennifer M. N.; Whisstock, James C.; Goscinski, Wojtek J.; Abramson, David; Buckle, Ashley M.

2010-01-01

Background The crystallographic determination of protein structures can be computationally demanding and for difficult cases can benefit from user-friendly interfaces to high-performance computing resources. Molecular replacement (MR) is a popular protein crystallographic technique that exploits the structural similarity between proteins that share some sequence similarity. But the need to trial permutations of search models, space group symmetries and other parameters makes MR time- and labour-intensive. However, MR calculations are embarrassingly parallel and thus ideally suited to distributed computing. In order to address this problem we have developed MrGrid, web-based software that allows multiple MR calculations to be executed across a grid of networked computers, allowing high-throughput MR. Methodology/Principal Findings MrGrid is a portable web based application written in Java/JSP and Ruby, and taking advantage of Apple Xgrid technology. Designed to interface with a user defined Xgrid resource the package manages the distribution of multiple MR runs to the available nodes on the Xgrid. We evaluated MrGrid using 10 different protein test cases on a network of 13 computers, and achieved an average speed up factor of 5.69. Conclusions MrGrid enables the user to retrieve and manage the results of tens to hundreds of MR calculations quickly and via a single web interface, as well as broadening the range of strategies that can be attempted. This high-throughput approach allows parameter sweeps to be performed in parallel, improving the chances of MR success. PMID:20386612

Response of algal metrics to nutrients and physical factors and identification of nutrient thresholds in agricultural streams

USGS Publications Warehouse

Black, R.W.; Moran, P.W.; Frankforter, J.D.

2011-01-01

Many streams within the United States are impaired due to nutrient enrichment, particularly in agricultural settings. The present study examines the response of benthic algal communities in agricultural and minimally disturbed sites from across the western United States to a suite of environmental factors, including nutrients, collected at multiple scales. The first objective was to identify the relative importance of nutrients, habitat and watershed features, and macroinvertebrate trophic structure to explain algal metrics derived from deposition and erosion habitats. The second objective was to determine if thresholds in total nitrogen (TN) and total phosphorus (TP) related to algal metrics could be identified and how these thresholds varied across metrics and habitats. Nutrient concentrations within the agricultural areas were elevated and greater than published threshold values. All algal metrics examined responded to nutrients as hypothesized. Although nutrients typically were the most important variables in explaining the variation in each of the algal metrics, environmental factors operating at multiple scales also were important. Calculated thresholds for TN or TP based on the algal metrics generated from samples collected from erosion and deposition habitats were not significantly different. Little variability in threshold values for each metric for TN and TP was observed. The consistency of the threshold values measured across multiple metrics and habitats suggest that the thresholds identified in this study are ecologically relevant. Additional work to characterize the relationship between algal metrics, physical and chemical features, and nuisance algal growth would be of benefit to the development of nutrient thresholds and criteria. ?? 2010 The Author(s).

Quantifying Multiple Work-Related Psychosocial Risk Factors: Proposal for a Composite Indicator Based on the COPSOQ II.

PubMed

Stauder, Adrienne; Nistor, Katalin; Zakor, Tünde; Szabó, Anita; Nistor, Anikó; Ádám, Szilvia; Konkolÿ Thege, Barna

2017-12-01

To determine national reference values for the Copenhagen Psychosocial Questionnaire (COPSOQ II) across occupational sectors and develop a composite score to estimate the cumulative effect of multiple work-related stressors, in order to facilitate the implementation of occupational health directives on psychosocial risk assessment. Cross-sectional data was collected via an online questionnaire. The sample included 13,104 individuals and was representative of the general Hungarian adult working population in terms of gender, age, education, and occupation. Mean scores were calculated for 18 scales on work environment and for 5 outcome scales of the COPSOQ II across 18 occupational sectors. We analyzed the association between a composite psychosocial risk score (CPRS), reflecting severity of exposure to multiple risk factors, and high stress, burnout, sleep troubles, and poor self-rated health. We found occupation-related differences in the mean scores on all COPSOQ II scales. Scores on the "Stress" scale ranged from 47.9 to 56.2, with the highest mean score in accommodation and food services sector. Variability was greatest with respect to emotional demands (range 40.3-67.6) and smallest with respect to role clarity (range 70.3-75.7). The prevalence of negative health outcomes increased with the CPRS. Five risk categories were formed, for which the odds ratio of negative outcomes ranged from 1.6 to 56.5. The sector-specific psychosocial risk profiles covering 18 work environmental factors can be used as a reference in organizational surveys and international comparisons. The CPRS proved to be a powerful predictor of self-reported negative health outcomes.

Response of algal metrics to nutrients and physical factors and identification of nutrient thresholds in agricultural streams.

PubMed

Black, Robert W; Moran, Patrick W; Frankforter, Jill D

2011-04-01

Many streams within the United States are impaired due to nutrient enrichment, particularly in agricultural settings. The present study examines the response of benthic algal communities in agricultural and minimally disturbed sites from across the western United States to a suite of environmental factors, including nutrients, collected at multiple scales. The first objective was to identify the relative importance of nutrients, habitat and watershed features, and macroinvertebrate trophic structure to explain algal metrics derived from deposition and erosion habitats. The second objective was to determine if thresholds in total nitrogen (TN) and total phosphorus (TP) related to algal metrics could be identified and how these thresholds varied across metrics and habitats. Nutrient concentrations within the agricultural areas were elevated and greater than published threshold values. All algal metrics examined responded to nutrients as hypothesized. Although nutrients typically were the most important variables in explaining the variation in each of the algal metrics, environmental factors operating at multiple scales also were important. Calculated thresholds for TN or TP based on the algal metrics generated from samples collected from erosion and deposition habitats were not significantly different. Little variability in threshold values for each metric for TN and TP was observed. The consistency of the threshold values measured across multiple metrics and habitats suggest that the thresholds identified in this study are ecologically relevant. Additional work to characterize the relationship between algal metrics, physical and chemical features, and nuisance algal growth would be of benefit to the development of nutrient thresholds and criteria.

Tensor numerical methods in quantum chemistry: from Hartree-Fock to excitation energies.

PubMed

Khoromskaia, Venera; Khoromskij, Boris N

2015-12-21

We resume the recent successes of the grid-based tensor numerical methods and discuss their prospects in real-space electronic structure calculations. These methods, based on the low-rank representation of the multidimensional functions and integral operators, first appeared as an accurate tensor calculus for the 3D Hartree potential using 1D complexity operations, and have evolved to entirely grid-based tensor-structured 3D Hartree-Fock eigenvalue solver. It benefits from tensor calculation of the core Hamiltonian and two-electron integrals (TEI) in O(n log n) complexity using the rank-structured approximation of basis functions, electron densities and convolution integral operators all represented on 3D n × n × n Cartesian grids. The algorithm for calculating TEI tensor in a form of the Cholesky decomposition is based on multiple factorizations using algebraic 1D "density fitting" scheme, which yield an almost irreducible number of product basis functions involved in the 3D convolution integrals, depending on a threshold ε > 0. The basis functions are not restricted to separable Gaussians, since the analytical integration is substituted by high-precision tensor-structured numerical quadratures. The tensor approaches to post-Hartree-Fock calculations for the MP2 energy correction and for the Bethe-Salpeter excitation energies, based on using low-rank factorizations and the reduced basis method, were recently introduced. Another direction is towards the tensor-based Hartree-Fock numerical scheme for finite lattices, where one of the numerical challenges is the summation of electrostatic potentials of a large number of nuclei. The 3D grid-based tensor method for calculation of a potential sum on a L × L × L lattice manifests the linear in L computational work, O(L), instead of the usual O(L(3) log L) scaling by the Ewald-type approaches.

RESOLVED GIANT MOLECULAR CLOUDS IN NEARBY SPIRAL GALAXIES: INSIGHTS FROM THE CANON CO (1-0) SURVEY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Donovan Meyer, Jennifer; Koda, Jin; Mooney, Thomas

We resolve 182 individual giant molecular clouds (GMCs) larger than 2.5 Multiplication-Sign 10{sup 5} M{sub Sun} in the inner disks of 5 large nearby spiral galaxies (NGC 2403, NGC 3031, NGC 4736, NGC 4826, and NGC 6946) to create the largest such sample of extragalactic GMCs within galaxies analogous to the Milky Way. Using a conservatively chosen sample of GMCs most likely to adhere to the virial assumption, we measure cloud sizes, velocity dispersions, and {sup 12}CO (J = 1-0) luminosities and calculate cloud virial masses. The average conversion factor from CO flux to H{sub 2} mass (or X{sub CO})more » for each galaxy is 1-2 Multiplication-Sign 10{sup 20} cm{sup -2} (K km s{sup -1}){sup -1}, all within a factor of two of the Milky Way disk value ({approx}2 Multiplication-Sign 10{sup 20} cm{sup -2} (K km s{sup -1}){sup -1}). We find GMCs to be generally consistent within our errors between the galaxies and with Milky Way disk GMCs; the intrinsic scatter between clouds is of order a factor of two. Consistent with previous studies in the Local Group, we find a linear relationship between cloud virial mass and CO luminosity, supporting the assumption that the clouds in this GMC sample are gravitationally bound. We do not detect a significant population of GMCs with elevated velocity dispersions for their sizes, as has been detected in the Galactic center. Though the range of metallicities probed in this study is narrow, the average conversion factors of these galaxies will serve to anchor the high metallicity end of metallicity-X{sub CO} trends measured using conversion factors in resolved clouds; this has been previously possible primarily with Milky Way measurements.« less

Thermoelastic damping effect of the micro-ring resonator with irregular mass and stiffness

NASA Astrophysics Data System (ADS)

Kim, Jung-Hwan; Kim, Ji-Hwan

2016-05-01

Fundamentally, vibration characteristic is a main factor for the stability of structures. In this regard, the irregularity of mass and stiffness distributions for the structure have been an interesting issue for many years. Recently, the Micro Electro Mechanical Systems (MEMS) are developed for various applications such as gyro sensors. In the present work, in-plane vibration of micro-ring structure with multiple finite-sized imperfections is investigated. Then, the unbalance of the structure is represented using Heaviside Step Function for the inextensional modeling of the ring. Also, thermoelastic damping (TED) due to internal friction is studied based on Fourier's one-dimensional heat conduction equation using Laplace Transform. To obtain the quality-factors (Q-factors) for imperfect micro-ring, analytical solutions are calculated from governing equations of motion with TED. And then, the natural frequencies and the Q-factors are observed to separate into lower and higher modes. Additionally, the vibration mode shapes are presented, and the frequency trimming concept due to attached imperfections is investigated.

Predictors of School Garden Integration: Factors Critical to Gardening Success in New York City.

PubMed

Burt, Kate Gardner; Burgermaster, Marissa; Jacquez, Raquel

2018-03-01

The purpose of this study was to determine the level of integration of school gardens and identify factors that predict integration. 211 New York City schools completed a survey that collected demographic information and utilized the School Garden Integration Scale. A mean garden integration score was calculated, and multiple regression analysis was conducted to determine independent predictors of integration and assess relationships between individual integration characteristics and budget. The average integration score was 34.1 (of 57 points) and ranged from 8 to 53. Operating budget had significant influence on integration score, controlling for all other factors ( p < .0001). Partner organizations, evaluation/feedback, planning the physical space, and characteristics of the physical space were positively and significantly related to budget. The results of this study indicate that any garden can become well integrated, as budget is a modifiable factor. When adequate funding is secured, a well-integrated garden may be established with proper planning and sound implementation.

Prise en compte d'un couplage fin neutronique-thermique dans les calculs d'assemblage pour les reacteurs a eau pressurisee

NASA Astrophysics Data System (ADS)

Greiner, Nathan

Core simulations for Pressurized Water Reactors (PWR) is insured by a set of computer codes which allows, under certain assumptions, to approximate the physical quantities of interest, such as the effective multiplication factor or the power or temperature distributions. The neutronics calculation scheme relies on three great steps : -- the production of an isotopic cross-sections library ; -- the production of a reactor database through the lattice calculation ; -- the full-core calculation. In the lattice calculation, in which Boltzmann's transport equation is solved over an assembly geometry, the temperature distribution is uniform and constant during irradiation. This represents a set of approximations since, on the one hand, the temperature distribution in the assembly is not uniform (strong temperature gradients in the fuel pins, discrepancies between the fuel pins) and on the other hand, irradiation causes the thermal properties of the pins to change, which modifies the temperature distribution. Our work aims at implementing and introducing a neutronics-thermomechanics coupling into the lattice calculation to finely discretize the temperature distribution and to study its effects. To perform the study, CEA (Commissariat a l'Energie Atomique et aux Energies Alternatives) lattice code APOLLO2 was used for neutronics and EDF (Electricite De France) code C3THER was used for the thermal calculations. We show very small effects of the pin-scaled coupling when comparing the use of a temperature profile with the use of an uniform temperature over UOX-type and MOX-type fuels. We next investigate the thermal feedback using an assembly-scaled coupling taking into account the presence of large water gaps on an UOX-type assembly at burnup 0. We show the very small impact on the calculation of the hot spot factor. Finally, the coupling is introduced into the isotopic depletion calculation and we show that reactivity and isotopic number densities deviations remain small albeit not negligible for UOX-type and MOX-type assemblies. The specific behavior of gadolinium-stuffed fuel pins in an UO2Gd2O 3-type assembly is highlighted.

A fast calculating two-stream-like multiple scattering algorithm that captures azimuthal and elevation variations

NASA Astrophysics Data System (ADS)

Fiorino, Steven T.; Elmore, Brannon; Schmidt, Jaclyn; Matchefts, Elizabeth; Burley, Jarred L.

2016-05-01

Properly accounting for multiple scattering effects can have important implications for remote sensing and possibly directed energy applications. For example, increasing path radiance can affect signal noise. This study describes the implementation of a fast-calculating two-stream-like multiple scattering algorithm that captures azimuthal and elevation variations into the Laser Environmental Effects Definition and Reference (LEEDR) atmospheric characterization and radiative transfer code. The multiple scattering algorithm fully solves for molecular, aerosol, cloud, and precipitation single-scatter layer effects with a Mie algorithm at every calculation point/layer rather than an interpolated value from a pre-calculated look-up-table. This top-down cumulative diffusivity method first considers the incident solar radiance contribution to a given layer accounting for solid angle and elevation, and it then measures the contribution of diffused energy from previous layers based on the transmission of the current level to produce a cumulative radiance that is reflected from a surface and measured at the aperture at the observer. Then a unique set of asymmetry and backscattering phase function parameter calculations are made which account for the radiance loss due to the molecular and aerosol constituent reflectivity within a level and allows for a more accurate characterization of diffuse layers that contribute to multiple scattered radiances in inhomogeneous atmospheres. The code logic is valid for spectral bands between 200 nm and radio wavelengths, and the accuracy is demonstrated by comparing the results from LEEDR to observed sky radiance data.

Accelerating potential of mean force calculations for lipid membrane permeation: System size, reaction coordinate, solute-solute distance, and cutoffs

NASA Astrophysics Data System (ADS)

Nitschke, Naomi; Atkovska, Kalina; Hub, Jochen S.

2016-09-01

Molecular dynamics simulations are capable of predicting the permeability of lipid membranes for drug-like solutes, but the calculations have remained prohibitively expensive for high-throughput studies. Here, we analyze simple measures for accelerating potential of mean force (PMF) calculations of membrane permeation, namely, (i) using smaller simulation systems, (ii) simulating multiple solutes per system, and (iii) using shorter cutoffs for the Lennard-Jones interactions. We find that PMFs for membrane permeation are remarkably robust against alterations of such parameters, suggesting that accurate PMF calculations are possible at strongly reduced computational cost. In addition, we evaluated the influence of the definition of the membrane center of mass (COM), used to define the transmembrane reaction coordinate. Membrane-COM definitions based on all lipid atoms lead to artifacts due to undulations and, consequently, to PMFs dependent on membrane size. In contrast, COM definitions based on a cylinder around the solute lead to size-independent PMFs, down to systems of only 16 lipids per monolayer. In summary, compared to popular setups that simulate a single solute in a membrane of 128 lipids with a Lennard-Jones cutoff of 1.2 nm, the measures applied here yield a speedup in sampling by factor of ˜40, without reducing the accuracy of the calculated PMF.

Enhanced backscattering of optical waves due to densely distributed scatterers

NASA Astrophysics Data System (ADS)

Ma, Yushieh; Varadan, Vijay K.; Varadan, Vasundara V.

1988-01-01

Using multiple scattering theory, the T matrix of a pair of scatterers which takes all back-and-forth scattering between the pair members into account and considers multiple scattering effects in the intensity calculation is used to calculate the magnitude and the width of the backscattered intensity peak. Generally, at low concentrations, both the magnitude of the scattered intensity and multiple scattering contributions are not sufficiently strong to reach the enhanced-backscattering threshold. The results obtained are consistent with those yielded by optical experiments.

Computing Fault Displacements from Surface Deformations

NASA Technical Reports Server (NTRS)

Lyzenga, Gregory; Parker, Jay; Donnellan, Andrea; Panero, Wendy

2006-01-01

Simplex is a computer program that calculates locations and displacements of subterranean faults from data on Earth-surface deformations. The calculation involves inversion of a forward model (given a point source representing a fault, a forward model calculates the surface deformations) for displacements, and strains caused by a fault located in isotropic, elastic half-space. The inversion involves the use of nonlinear, multiparameter estimation techniques. The input surface-deformation data can be in multiple formats, with absolute or differential positioning. The input data can be derived from multiple sources, including interferometric synthetic-aperture radar, the Global Positioning System, and strain meters. Parameters can be constrained or free. Estimates can be calculated for single or multiple faults. Estimates of parameters are accompanied by reports of their covariances and uncertainties. Simplex has been tested extensively against forward models and against other means of inverting geodetic data and seismic observations. This work

Indirect estimation of emission factors for phosphate surface mining using air dispersion modeling.

PubMed

Tartakovsky, Dmitry; Stern, Eli; Broday, David M

2016-06-15

To date, phosphate surface mining suffers from lack of reliable emission factors. Due to complete absence of data to derive emissions factors, we developed a methodology for estimating them indirectly by studying a range of possible emission factors for surface phosphate mining operations and comparing AERMOD calculated concentrations to concentrations measured around the mine. We applied this approach for the Khneifiss phosphate mine, Syria, and the Al-Hassa and Al-Abyad phosphate mines, Jordan. The work accounts for numerous model unknowns and parameter uncertainties by applying prudent assumptions concerning the parameter values. Our results suggest that the net mining operations (bulldozing, grading and dragline) contribute rather little to ambient TSP concentrations in comparison to phosphate processing and transport. Based on our results, the common practice of deriving the emission rates for phosphate mining operations from the US EPA emission factors for surface coal mining or from the default emission factor of the EEA seems to be reasonable. Yet, since multiple factors affect dispersion from surface phosphate mines, a range of emission factors, rather than only a single value, was found to satisfy the model performance. Copyright © 2016 Elsevier B.V. All rights reserved.

Multiple Scattering Effects on Pulse Propagation in Optically Turbid Media.

NASA Astrophysics Data System (ADS)

Joelson, Bradley David

The effects of multiple scattering in a optically turbid media is examined for an impulse solution to the radiative transfer equation for a variety of geometries and phase functions. In regions where the complexities of the phase function proved too cumbersome for analytic methods Monte Carlo techniques were developed to describe the entire scalar radiance distribution. The determination of a general spread function is strongly dependent on geometry and particular regions where limits can be placed on the variables of the problem. Hence, the general spread function is first simplified by considering optical regions which reduce the complexity of the variable dependence. First, in the small-angle limit we calculate some contracted spread functions along with their moments and then use Monte Carlo techniques to establish the limitations imposed by the small-angle approximation in planar geometry. The point spread function (PSF) for a spherical geometry is calculated for the full angular spread in the forward direction of ocean waters using Monte Carlo methods in the optically thin and moderate depths and analytic methods in the diffusion domain. The angular dependence of the PSF for various ocean waters is examined for a range of optical parameters. The analytic method used in the diffusion calculation is justified by examining the angular dependence of the radiance of a impulse solution in a planar geometry for a prolongated Henyey-Greenstein phase function of asymmetry factor approximately equal to that of the ocean phase functions. The Legendre moments of the radiance are examined in order to examine the viability of the diffusion approximation which assumes a linearly anisotropic angular distribution for the radiance. A realistic lidar calculation is performed for a variety of ocean waters to determine the effects of multiple scattering on the determination of the speed of sound by using the range gated frequency spectrum of the lidar signal. It is shown that the optical properties of the ocean help to ensure single scatter form for the frequency spectra of the lidar signal. This spectra can then be used to compute the speed of sound and backscatter probability.

[Study of building quantitative analysis model for chlorophyll in winter wheat with reflective spectrum using MSC-ANN algorithm].

PubMed

Liang, Xue; Ji, Hai-yan; Wang, Peng-xin; Rao, Zhen-hong; Shen, Bing-hui

2010-01-01

Preprocess method of multiplicative scatter correction (MSC) was used to reject noises in the original spectra produced by the environmental physical factor effectively, then the principal components of near-infrared spectroscopy were calculated by nonlinear iterative partial least squares (NIPALS) before building the back propagation artificial neural networks method (BP-ANN), and the numbers of principal components were calculated by the method of cross validation. The calculated principal components were used as the inputs of the artificial neural networks model, and the artificial neural networks model was used to find the relation between chlorophyll in winter wheat and reflective spectrum, which can predict the content of chlorophyll in winter wheat. The correlation coefficient (r) of calibration set was 0.9604, while the standard deviation (SD) and relative standard deviation (RSD) was 0.187 and 5.18% respectively. The correlation coefficient (r) of predicted set was 0.9600, and the standard deviation (SD) and relative standard deviation (RSD) was 0.145 and 4.21% respectively. It means that the MSC-ANN algorithm can reject noises in the original spectra produced by the environmental physical factor effectively and set up an exact model to predict the contents of chlorophyll in living leaves veraciously to replace the classical method and meet the needs of fast analysis of agricultural products.

Price Analysis of Railway Freight Transport under Marketing Mechanism

NASA Astrophysics Data System (ADS)

Shi, Ying; Fang, Xiaoping; Chen, Zhiya

Regarding the problems in the reform of the railway tariff system and the pricing of the transport, by means of assaying the influence of the price elasticity on the artifice used for price, this article proposed multiple regressive model which analyzed price elasticity quantitatively. This model conclude multi-factors which influences on the price elasticity, such as the averagely railway freight charge, the averagely freight haulage of proximate supersede transportation mode, the GDP per capita in the point of origin, and a series of dummy variable which can reflect the features of some productive and consume demesne. It can calculate the price elasticity of different classes in different domains, and predict the freight traffic volume on different rate levels. It can calculate confidence-level, and evaluate the relevance of each parameter to get rid of irrelevant or little relevant variables. It supplied a good theoretical basis for directing the pricing of transport enterprises in market economic conditions, which is suitable for railway freight, passenger traffic and other transportation manner as well. SPSS (Statistical Package for the Social Science) software was used to calculate and analysis the example. This article realized the calculation by HYFX system(Ministry of Railways fund).

Aerodynamic analysis of the Darrieus rotor including secondary effects

NASA Astrophysics Data System (ADS)

Paraschivoiu, I.; Delclaux, F.; Fraunie, P.; Beguier, C.

1983-10-01

An aerodynamic analysis is made of two variants of the two-actuator-disk theory for modeling the Darrieus wind turbine. The double-multiple-streamtube model with constant and variable interference factors, including secondary effects, is examined for a Darrieus rotor. The influence of the secondary effects, namely, the blade geometry and profile type, the rotating tower, and the presence of struts and aerodynamic spoilers, is relatively significant, especially at high tip-speed ratios. Variation of the induced velocity as a function of the azimuthal angle allows a more accurate calculation of the aerodynamic loads on the downwind zone of the rotor with respect to the assumed constant interference factors. The theoretical results were compared with available experimental data for the Magdalen Islands wind turbine and Sandia-type machines (straight-line/circular-arc shape).

Nuclear data uncertainty propagation by the XSUSA method in the HELIOS2 lattice code

NASA Astrophysics Data System (ADS)

Wemple, Charles; Zwermann, Winfried

2017-09-01

Uncertainty quantification has been extensively applied to nuclear criticality analyses for many years and has recently begun to be applied to depletion calculations. However, regulatory bodies worldwide are trending toward requiring such analyses for reactor fuel cycle calculations, which also requires uncertainty propagation for isotopics and nuclear reaction rates. XSUSA is a proven methodology for cross section uncertainty propagation based on random sampling of the nuclear data according to covariance data in multi-group representation; HELIOS2 is a lattice code widely used for commercial and research reactor fuel cycle calculations. This work describes a technique to automatically propagate the nuclear data uncertainties via the XSUSA approach through fuel lattice calculations in HELIOS2. Application of the XSUSA methodology in HELIOS2 presented some unusual challenges because of the highly-processed multi-group cross section data used in commercial lattice codes. Currently, uncertainties based on the SCALE 6.1 covariance data file are being used, but the implementation can be adapted to other covariance data in multi-group structure. Pin-cell and assembly depletion calculations, based on models described in the UAM-LWR Phase I and II benchmarks, are performed and uncertainties in multiplication factor, reaction rates, isotope concentrations, and delayed-neutron data are calculated. With this extension, it will be possible for HELIOS2 users to propagate nuclear data uncertainties directly from the microscopic cross sections to subsequent core simulations.

Prevalence of multiple organ dysfunction in the pediatric intensive care unit: Pediatric Risk of Mortality III versus Pediatric Logistic Organ Dysfunction scores for mortality prediction

PubMed Central

Hamshary, Azza Abd Elkader El; Sherbini, Seham Awad El; Elgebaly, HebatAllah Fadel; Amin, Samah Abdelkrim

2017-01-01

Objectives To assess the frequency of primary multiple organ failure and the role of sepsis as a causative agent in critically ill pediatric patients; and calculate and evaluate the accuracy of the Pediatric Risk of Mortality III (PRISM III) and Pediatric Logistic Organ Dysfunction (PELOD) scores to predict the outcomes of critically ill children. Methods Retrospective study, which evaluated data from patients admitted from January to December 2011 in the pediatric intensive care unit of the Children's Hospital of the University of Cairo. Results Out of 237 patients in the study, 72% had multiple organ dysfunctions, and 45% had sepsis with multiple organ dysfunctions. The mortality rate in patients with multiple organ dysfunction was 73%. Independent risk factors for death were mechanical ventilation and neurological failure [OR: 36 and 3.3, respectively]. The PRISM III score was more accurate than the PELOD score in predicting death, with a Hosmer-Lemeshow X2 (Chi-square value) of 7.3 (df = 8, p = 0.5). The area under the curve was 0.723 for PRISM III and 0.78 for PELOD. Conclusion A multiple organ dysfunctions was associated with high mortality. Sepsis was the major cause. Pneumonia, diarrhea and central nervous system infections were the major causes of sepsis. PRISM III had a better calibration than the PELOD for prognosis of the patients, despite the high frequency of the multiple organ dysfunction syndrome. PMID:28977260

Multiple Contact Dates and SARS Incubation Periods

PubMed Central

2004-01-01

Many severe acute respiratory syndrome (SARS) patients have multiple possible incubation periods due to multiple contact dates. Multiple contact dates cannot be used in standard statistical analytic techniques, however. I present a simple spreadsheet-based method that uses multiple contact dates to calculate the possible incubation periods of SARS. PMID:15030684

Direct system parameter identification of mechanical structures with application to modal analysis

NASA Technical Reports Server (NTRS)

Leuridan, J. M.; Brown, D. L.; Allemang, R. J.

1982-01-01

In this paper a method is described to estimate mechanical structure characteristics in terms of mass, stiffness and damping matrices using measured force input and response data. The estimated matrices can be used to calculate a consistent set of damped natural frequencies and damping values, mode shapes and modal scale factors for the structure. The proposed technique is attractive as an experimental modal analysis method since the estimation of the matrices does not require previous estimation of frequency responses and since the method can be used, without any additional complications, for multiple force input structure testing.

Study of diatomic molecules. 2: Intensities. [optical emission spectroscopy of ScO

NASA Technical Reports Server (NTRS)

Femenias, J. L.

1978-01-01

The theory of perturbations, giving the diatomic effective Hamiltonian, is used for calculating actual molecular wave functions and intensity factors involved in transitions between states arising from Hund's coupling cases a,b, intermediate a-b, and c tendency. The Herman and Wallis corrections are derived, without any knowledge of the analytical expressions of the wave functions, and generalized to transitions between electronic states with whatever symmetry and multiplicity. A general method for studying perturbed intensities is presented using primarily modern spectroscopic numerical approaches. The method is used in the study of the ScO optical emission spectrum.

Relational Reasoning about Numbers and Operations--Foundation for Calculation Strategy Use in Multi-Digit Multiplication and Division

ERIC Educational Resources Information Center

Schulz, Andreas

2018-01-01

Theoretical analysis of whole number-based calculation strategies and digit-based algorithms for multi-digit multiplication and division reveals that strategy use includes two kinds of reasoning: reasoning about the relations between numbers and reasoning about the relations between operations. In contrast, algorithms aim to reduce the necessary…

Sample Size Calculation for Estimating or Testing a Nonzero Squared Multiple Correlation Coefficient

ERIC Educational Resources Information Center

Krishnamoorthy, K.; Xia, Yanping

2008-01-01

The problems of hypothesis testing and interval estimation of the squared multiple correlation coefficient of a multivariate normal distribution are considered. It is shown that available one-sided tests are uniformly most powerful, and the one-sided confidence intervals are uniformly most accurate. An exact method of calculating sample size to…

Etude des performances de solveurs deterministes sur un coeur rapide a caloporteur sodium

NASA Astrophysics Data System (ADS)

Bay, Charlotte

The reactors of next generation, in particular SFR model, represent a true challenge for current codes and solvers, used mainly for thermic cores. There is no guarantee that their competences could be straight adapted to fast neutron spectrum, or to major design differences. Thus it is necessary to assess the validity of solvers and their potential shortfall in the case of fast neutron reactors. As part of an internship with CEA (France), and at the instigation of EPM Nuclear Institute, this study concerns the following codes : DRAGON/DONJON, ERANOS, PARIS and APOLLO3. The precision assessment has been performed using Monte Carlo code TRIPOLI4. Only core calculation was of interest, namely numerical methods competences in precision and rapidity. Lattice code was not part of the study, that is to say nuclear data, self-shielding, or isotopic compositions. Nor was tackled burnup or time evolution effects. The study consists in two main steps : first evaluating the sensitivity of each solver to calculation parameters, and obtain its optimal calculation set ; then compare their competences in terms of precision and rapidity, by collecting usual quantities (effective multiplication factor, reaction rates map), but also more specific quantities which are crucial to the SFR design, namely control rod worth and sodium void effect. The calculation time is also a key factor. Whatever conclusion or recommendation that could be drawn from this study, they must first of all be applied within similar frameworks, that is to say small fast neutron cores with hexagonal geometry. Eventual adjustments for big cores will have to be demonstrated in developments of this study.

Calculation of optical properties of dental composites as a basis for determining color impression and penetration depth of laser light

NASA Astrophysics Data System (ADS)

Weniger, Kirsten K.; Muller, Gerhard J.

2005-03-01

In order to achieve esthetic dental restorations, there should be no visible difference between restorative material and treated teeth. This requires a match of the optical properties of both restorative material and natural teeth. These optical properties are determined by absorption and scattering of light emerging not only on the surface but also inside the material. Investigating different dental composites in several shades, a method has been developed to calculate the optical parameters absorption coefficient μa, scattering coefficient μs, anisotropy factor g and reduced scattering coefficient μs'. The method includes sample preparation and measurements of transmittance and reflectance in an integrating sphere spectrometer, followed by inverse Monte Carlo simulations. Determination of optical properties is more precise and comprehensive than with the previously used Kubelka Munk theory because scattering can be looked at separated into pure scattering with the scattering coefficient μs and its direction with the anisotropy factor g. Moreover the use of the inverse Monte Carlo simulation not only minimizes systematic errors and considers the scattering phase function, but also takes into account the measuring geometry. The compilation of a data pool of optical parameters now enables the application of further calculation models as a basis for optimization of the composition of new materials. For example, a prediction of the general color impression for multiple layers can be carried out as well as the calculation of the wavelength dependent penetration depths of light with regard to photo polymerization. Further applications are possible in the area of laser ablation.

Thermal Photon Radiation in High Multiplicity p + Pb Collisions at the Large Hadron Collider

DOE PAGES

Shen, Chun; Paquet, Jean-François; Denicol, Gabriel S.; ...

2016-02-18

We observed the collective behavior of hadronic particles in high multiplicity proton-lead collisions at the Large Hadron Collider, as well as in deuteron-gold collisions at the Relativistic Heavy-Ion Collider. In our work we present the first calculation, in the hydrodynamic framework, of thermal photon radiation from such small collision systems. Owing to their compact size, these systems can reach temperatures comparable to those in central nucleus-nucleus collisions. Moreover, the thermal photons can thus shine over the prompt background, and increase the low p T direct photon spectrum by a factor of 2–3 in 0%–1% p+Pb collisions at 5.02 TeV. Thismore » thermal photon enhancement can therefore serve as a signature of the existence of a hot quark-gluon plasma during the evolution of these small collision systems, as well as validate hydrodynamic behavior in small systems.« less

Multiple coherent light scattering in ultracold rubidium

NASA Astrophysics Data System (ADS)

Kulatunga, P.; Sukenik, C. I.; Havey, M. D.; Kupriyanov, D. V.; Sokolov, I. M.

2001-11-01

We report investigation of multiple coherent light scattering from ^85Rb atoms confined in a magneto-optic trap. In a theoretical study of intensity enhancement of near-resonant backscattered light from cold ^85,87Rb atoms, we consider the dominant mode of double scattering only. Enhancement factors are calculated for all D1 and D2 hyperfine components and for both isotopes. In experimental studies, measurements are made of coherent backscattering of a low-intensity probe beam tuned near the F = 3 - F' = 4 transition in ^85Rb atoms. Polarization of backscattered light is determined by a backscattering polarimeter; the spatial distribution of light intensity is measured by a liquid-nitrogen cooled CCD camera set in the focal plane of the analyzing optics. The instrument has angular resolution of about 100 micro-radians, and a polarization analyzing power of roughly 1000. In this paper we describe the instrument details, including calibration procedures, and progress towards observation of atomic coherent backscattering.

Multiple coherent light scattering in ultracold rubidium

NASA Astrophysics Data System (ADS)

Havey, M. D.; Sukenik, C. I.; Kulatunga, P.; Kupriyanov, D. V.; Sokolov, I. M.

2001-05-01

We report investigation of multiple coherent light scattering from ^85Rb atoms confined in a magneto-optic trap. In a theoretical study of intensity enhancement of near-resonant backscattered light from cold ^85,87Rb atoms, we consider the dominant mode of double scattering only. Enhancement factors are calculated for all D1 and D2 hyperfine components and for both isotopes. In experimental studies, measurements are made of coherent backscattering of a low-intensity probe beam tuned near the F = 3 - F' = 4 transition in ^85Rb atoms. Polarization of backscattered light is determined by a backscattering polarimeter; the spatial distribution of light intensity is measured by a liquid-nitrogen cooled CCD camera set in the focal plane of the analyzing optics. The instrument has angular resolution of about 100 micro-radians, and a polarization analyzing power of roughly 1000. In this paper we describe the instrument details, including calibration procedures, and progress towards observation of atomic coherent backscattering.

Are photographic records reliable for orthodontic screening?

PubMed

Mandall, N A

2002-06-01

The aim of the study was to evaluate the reliability of a panel of orthodontists for accepting new patient referrals based on clinical photographs. Eight orthodontists from Greater Manchester, Lancashire, Chester, and Derbyshire observed clinical photographs of 40 consecutive new patients attending the orthodontic department, Hope Hospital, Salford. They recorded whether or not they would accept the patient, as a new patient referral, in their department. Each consultant was asked to take into account factors, such as oral hygiene, dental development, and severity of the malocclusion. Kappa statistic for multiple-rater agreement and kappa statistic for intra-observer reliability were calculated. Inter-observer panel agreement for accepting new patient referrals based on photographic information was low (multiple rater kappa score 0.37). Intra-examiner agreement was better (kappa range 0.34-0.90). Clinician agreement for screening and accepting orthodontic referrals based on clinical photographs is comparable to that previously reported for other clinical decision making.

Next-to-leading order QCD predictions for top-quark pair production with up to three jets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Höche, S.; Maierhöfer, P.; Moretti, N.

2017-03-07

Here, we present theoretical predictions for the production of top-quark pairs with up to three jets at the next-to leading order in perturbative QCD. The relevant calculations are performed with Sherpa and OpenLoops. In order to address the issue of scale choices and related uncertainties in the presence of multiple scales, we compare results obtained with the standard scale HT/2HT/2 at fixed order and the MiNLO procedure. By analyzing various cross sections and distributions for tmore » $$\\bar{t}$$+0,1,2,3 jets at the 13 TeV LHC we found a remarkable overall agreement between fixed-order and MiNLO results. The differences are typically below the respective factor-two scale variations, suggesting that for all considered jet multiplicities missing higher-order effects should not exceed the ten percent level.« less

IOTA: the array controller for a gigapixel OTCCD camera for Pan-STARRS

NASA Astrophysics Data System (ADS)

Onaka, Peter; Tonry, John; Luppino, Gerard; Lockhart, Charles; Lee, Aaron; Ching, Gregory; Isani, Sidik; Uyeshiro, Robin

2004-09-01

The PanSTARRS project has undertaken an ambitious effort to develop a completely new array controller architecture that is fundamentally driven by the large 1gigapixel, low noise, high speed OTCCD mosaic requirements as well as the size, power and weight restrictions of the PanSTARRS telescope. The result is a very small form factor next generation controller scalar building block with 1 Gigabit Ethernet interfaces that will be assembled into a system that will readout 512 outputs at ~1 Megapixel sample rates on each output. The paper will also discuss critical technology and fabrication techniques such as greater than 1MHz analog to digital converters (ADCs), multiple fast sampling and digital calculation of multiple correlated samples (DMCS), ball grid array (BGA) packaged circuits, LINUX running on embedded field programmable gate arrays (FPGAs) with hard core microprocessors for the prototype currently being developed.

Detecting a Weak Association by Testing its Multiple Perturbations: a Data Mining Approach

NASA Astrophysics Data System (ADS)

Lo, Min-Tzu; Lee, Wen-Chung

2014-05-01

Many risk factors/interventions in epidemiologic/biomedical studies are of minuscule effects. To detect such weak associations, one needs a study with a very large sample size (the number of subjects, n). The n of a study can be increased but unfortunately only to an extent. Here, we propose a novel method which hinges on increasing sample size in a different direction-the total number of variables (p). We construct a p-based `multiple perturbation test', and conduct power calculations and computer simulations to show that it can achieve a very high power to detect weak associations when p can be made very large. As a demonstration, we apply the method to analyze a genome-wide association study on age-related macular degeneration and identify two novel genetic variants that are significantly associated with the disease. The p-based method may set a stage for a new paradigm of statistical tests.

Sarcopenia Impairs Prognosis of Patients with Hepatocellular Carcinoma: The Role of Liver Functional Reserve and Tumor-Related Factors in Loss of Skeletal Muscle Volume.

PubMed

Imai, Kenji; Takai, Koji; Watanabe, Satoshi; Hanai, Tatsunori; Suetsugu, Atsushi; Shiraki, Makoto; Shimizu, Masahito

2017-09-22

Sarcopenia impairs survival in patients with hepatocellular carcinoma (HCC). This study aimed to clarify the factors that contribute to decreased skeletal muscle volume in patients with HCC. The third lumbar vertebra skeletal muscle index (L3 SMI) in 351 consecutive patients with HCC was calculated to identify sarcopenia. Sarcopenia was defined as an L3 SMI value ≤ 29.0 cm²/m² for women and ≤ 36.0 cm²/m² for men. The factors affecting L3 SMI were analyzed by multiple linear regression analysis and tree-based models. Of the 351 HCC patients, 33 were diagnosed as having sarcopenia and showed poor prognosis compared with non-sarcopenia patients ( p = 0.007). However, this significant difference disappeared after the adjustments for age, sex, Child-Pugh score, maximum tumor size, tumor number, and the degree of portal vein invasion by propensity score matching analysis. Multiple linear regression analysis showed that age ( p = 0.015) and sex ( p < 0.0001) were significantly correlated with a decrease in L3 SMI. Tree-based models revealed that sex (female) is the most significant factor that affects L3 SMI. In male patients, L3 SMI was decreased by aging, increased Child-Pugh score (≥56 years), and enlarged tumor size (<56 years). Maintaining liver functional reserve and early diagnosis and therapy for HCC are vital to prevent skeletal muscle depletion and improve the prognosis of patients with HCC.

Religiousness as a factor of hesitation against doping behavior in college-age athletes.

PubMed

Zenic, Natasa; Stipic, Marija; Sekulic, Damir

2013-06-01

Religiousness is rarely studied as protective factor against substance use and misuse in sport. Further, we have found no investigation where college-age athletes were sampled and studied accordingly. The aim of the present study was to identify gender-specific protective effects of the religiousness (measured by Santa Clara Questionnaire) and other social, educational, and sport variables as a potential factors of hesitation against doping behaviors in sport-science-students from Mostar, Bosnia, and Herzegovina (51 women and 111 men; age range, 18-26). The gender differences for the non-parametric variables were established by Kruskall-Wallis test, while for the parametric variables the t-test for independent samples was used. Multiple regression calculations revealed religiousness as the most significant predictor of the social, health, sport and legal factors of hesitation against doping behaviors in both genders. However, the differential influence of the social, educational, sport and religious factors in relation to negative consequences of the doping behaviors is found for men and women. Such differential influence must be emphasized in tailoring the anti-doping policy and interventions.

Method and computer program product for maintenance and modernization backlogging

DOEpatents

Mattimore, Bernard G; Reynolds, Paul E; Farrell, Jill M

2013-02-19

According to one embodiment, a computer program product for determining future facility conditions includes a computer readable medium having computer readable program code stored therein. The computer readable program code includes computer readable program code for calculating a time period specific maintenance cost, for calculating a time period specific modernization factor, and for calculating a time period specific backlog factor. Future facility conditions equal the time period specific maintenance cost plus the time period specific modernization factor plus the time period specific backlog factor. In another embodiment, a computer-implemented method for calculating future facility conditions includes calculating a time period specific maintenance cost, calculating a time period specific modernization factor, and calculating a time period specific backlog factor. Future facility conditions equal the time period specific maintenance cost plus the time period specific modernization factor plus the time period specific backlog factor. Other embodiments are also presented.

Monte Carlo analysis of TRX lattices with ENDF/B version 3 data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hardy, J. Jr.

1975-03-01

Four TRX water-moderated lattices of slightly enriched uranium rods have been reanalyzed with consistent ENDF/B Version 3 data by means of the full-range Monte Carlo program RECAP. The following measured lattice parameters were studied: ratio of epithermal-to-thermal $sup 238$U capture, ratio of epithermal- to-thermal $sup 235$U fissions, ration of $sup 238$U captures to $sup 235$U fissions, ratio of $sup 238$U fissions to $sup 235$U fissions, and multiplication factor. In addition to the base calculations, some studies were done to find sensitivity of the TRX lattice parameters to selected variations of cross section data. Finally, additional experimental evidence is afforded bymore » effective $sup 238$U capture integrals for isolated rods. Shielded capture integrals were calculated for $sup 238$U metal and oxide rods. These are compared with other measurements. (auth)« less

Effects of the Application of the New Nuclear Data Library ENDF/B to the Criticality Analysis of AP1000

NASA Astrophysics Data System (ADS)

Kuntoro, Iman; Sembiring, T. M.; Susilo, Jati; Deswandri; Sunaryo, G. R.

2018-02-01

Calculations of criticality of the AP1000 core due to the use of new edition of nuclear data library namely ENDF/B-VII and ENDF/B-VII.1 have been done. This work is aimed to know the accuracy of ENDF/B-VII.1 compared to ENDF/B-VII and ENDF/B-VI.8. in determining the criticality parameter of AP1000. Analysis ws imposed to core at cold zero power (CZP) conditions. The calculations have been carried out by means of MCNP computer code for 3 dimension geometry. The results show that criticality parameter namely effective multiplication factor of the AP1000 core are higher than that ones resulted from ENDF/B-VI.8 with relative differences of 0.39% for application of ENDF/B-VII and of 0.34% for application of ENDF/B-VII.1.

Resummation of high order corrections in Higgs boson plus jet production at the LHC

DOE PAGES

Sun, Peng; Isaacson, Joshua; Yuan, C. -P.; ...

2017-02-22

We study the effect of multiple parton radiation to Higgs boson plus jet production at the LHC. The large logarithms arising from the small imbalance in the transverse momentum of the Higgs boson plus jet final state system are resummed to all orders in the expansion of the strong interaction coupling at the accuracy of Next-to-Leading Logarithm (NLL), by applying the transverse momentum dependent (TMD) factorization formalism. We show that the appropriate resummation scale should be the jet transverse momentum, rather than the partonic center of mass energy which has been normally used in the TMD resummation formalism. Furthermore, themore » transverse momentum distribution of the Higgs boson, particularly near the lower cut-off applied on the jet transverse momentum, can only be reliably predicted by the resummation calculation which is free of the so-called Sudakov-shoulder singularity problem, present in fixed-order calculations.« less

ON CRITICAL MASS ANALYSIS OF JRR-2

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1961-01-01

The critica mass of the JRR-2 was found to be 15 fuel elements, instead of 8 as expected, when the reactor reached criticaity. The critica mass was analyzed by AMF and JAERI a few years ago, but afterwards some modifications have been made of the stucture for the reinforcement, for example, during the construction. The critical mass is recalculated perfectly and the difference bctween 15 and S fuel elements is discussed. The deviation of the critical mass is mainly caused by the effects of control rods, fuel elcments, grid-plate, etc., in the reflector; only heavy water or light water wasmore » conaidered as the reflector in the previous calculation. A simple method is used to calculate the critical mass. The effective multiplication factor for the core with 15 fuel elements is obtained about 2% higher than the experimental value. This difference is also discussed in detail. (auth)« less

Resummation of high order corrections in Higgs boson plus jet production at the LHC

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Peng; Isaacson, Joshua; Yuan, C. -P.

We study the effect of multiple parton radiation to Higgs boson plus jet production at the LHC. The large logarithms arising from the small imbalance in the transverse momentum of the Higgs boson plus jet final state system are resummed to all orders in the expansion of the strong interaction coupling at the accuracy of Next-to-Leading Logarithm (NLL), by applying the transverse momentum dependent (TMD) factorization formalism. We show that the appropriate resummation scale should be the jet transverse momentum, rather than the partonic center of mass energy which has been normally used in the TMD resummation formalism. Furthermore, themore » transverse momentum distribution of the Higgs boson, particularly near the lower cut-off applied on the jet transverse momentum, can only be reliably predicted by the resummation calculation which is free of the so-called Sudakov-shoulder singularity problem, present in fixed-order calculations.« less

Multivariate meta-analysis using individual participant data.

PubMed

Riley, R D; Price, M J; Jackson, D; Wardle, M; Gueyffier, F; Wang, J; Staessen, J A; White, I R

2015-06-01

When combining results across related studies, a multivariate meta-analysis allows the joint synthesis of correlated effect estimates from multiple outcomes. Joint synthesis can improve efficiency over separate univariate syntheses, may reduce selective outcome reporting biases, and enables joint inferences across the outcomes. A common issue is that within-study correlations needed to fit the multivariate model are unknown from published reports. However, provision of individual participant data (IPD) allows them to be calculated directly. Here, we illustrate how to use IPD to estimate within-study correlations, using a joint linear regression for multiple continuous outcomes and bootstrapping methods for binary, survival and mixed outcomes. In a meta-analysis of 10 hypertension trials, we then show how these methods enable multivariate meta-analysis to address novel clinical questions about continuous, survival and binary outcomes; treatment-covariate interactions; adjusted risk/prognostic factor effects; longitudinal data; prognostic and multiparameter models; and multiple treatment comparisons. Both frequentist and Bayesian approaches are applied, with example software code provided to derive within-study correlations and to fit the models. © 2014 The Authors. Research Synthesis Methods published by John Wiley & Sons, Ltd.

Improving risk assessment in schizophrenia: epidemiological investigation of criminal history factors

PubMed Central

Witt, Katrina; Lichtenstein, Paul; Fazel, Seena

2015-01-01

Background Violence risk assessment in schizophrenia relies heavily on criminal history factors. Aims To investigate which criminal history factors are most strongly associated with violent crime in schizophrenia. Method A total of 13 806 individuals (8891 men and 4915 women) with two or more hospital admissions for schizophrenia were followed up for violent convictions. Multivariate hazard ratios for 15 criminal history factors included in different risk assessment tools were calculated. The incremental predictive validity of these factors was estimated using tests of discrimination, calibration and reclassification. Results Over a mean follow-up of 12.0 years, 17.3% of men (n = 1535) and 5.7% of women (n = 281) were convicted of a violent offence. Criminal history factors most strongly associated with subsequent violence for both men and women were a previous conviction for a violent offence; for assault, illegal threats and/or intimidation; and imprisonment. However, only a previous conviction for a violent offence was associated with incremental predictive validity in both genders following adjustment for young age and comorbid substance use disorder. Conclusions Clinical and actuarial approaches to assess violence risk can be improved if included risk factors are tested using multiple measures of performance. PMID:25657352

Improving risk assessment in schizophrenia: epidemiological investigation of criminal history factors.

PubMed

Witt, Katrina; Lichtenstein, Paul; Fazel, Seena

2015-05-01

Violence risk assessment in schizophrenia relies heavily on criminal history factors. To investigate which criminal history factors are most strongly associated with violent crime in schizophrenia. A total of 13 806 individuals (8891 men and 4915 women) with two or more hospital admissions for schizophrenia were followed up for violent convictions. Multivariate hazard ratios for 15 criminal history factors included in different risk assessment tools were calculated. The incremental predictive validity of these factors was estimated using tests of discrimination, calibration and reclassification. Over a mean follow-up of 12.0 years, 17.3% of men (n = 1535) and 5.7% of women (n = 281) were convicted of a violent offence. Criminal history factors most strongly associated with subsequent violence for both men and women were a previous conviction for a violent offence; for assault, illegal threats and/or intimidation; and imprisonment. However, only a previous conviction for a violent offence was associated with incremental predictive validity in both genders following adjustment for young age and comorbid substance use disorder. Clinical and actuarial approaches to assess violence risk can be improved if included risk factors are tested using multiple measures of performance. © The Royal College of Psychiatrists 2015.

Triglyceride glucose index and common carotid wall shear stress.

PubMed

Tripolino, Cesare; Irace, Concetta; Scavelli, Faustina B; de Franceschi, Maria S; Esposito, Teresa; Carallo, Claudio; Gnasso, Agostino

2014-02-01

Alterations in wall shear stress contribute to both clinical and subclinical atherosclerosis. Several conditions such as hypertension, diabetes, and obesity can impair shear stress, but the role of insulin resistance has never been investigated. The present study was designed to investigate whether insulin resistance assessed by TyG Index associates with wall shear stress in the common carotid artery. One hundred six individuals were enrolled. Blood pressure, lipids, glucose, and cigarette smoking were evaluated. TyG Index was calculated as log[fasting triglycerides × fasting glucose / 2]. Subjects underwent blood viscosity measurement and echo-Doppler evaluation of carotid arteries to calculate wall shear stress. The association between TyG Index and carotid wall shear stress was assessed by simple and multiple regression analyses. TyG Index was significantly and inversely associated with carotid wall shear stress both in simple (r = -0.44, P < 0.001) and multiple regression analyses accounting for age, sex, and major cardiovascular risk factors. The association was further confirmed after exclusion of subjects with diabetes, dyslipidemia, fasting blood glucose greater than 100 mg/dL, and triglycerides greater than 150 mg/dL. The present findings suggest that increasing insulin resistance, as assessed by TyG Index, associates with atherosclerosis-prone shear stress reduction in the common carotid artery.

On functional determinants of matrix differential operators with multiple zero modes

NASA Astrophysics Data System (ADS)

Falco, G. M.; Fedorenko, Andrei A.; Gruzberg, Ilya A.

2017-12-01

We generalize the method of computing functional determinants with a single excluded zero eigenvalue developed by McKane and Tarlie to differential operators with multiple zero eigenvalues. We derive general formulas for such functional determinants of r× r matrix second order differential operators O with 0 < n ≤slant 2r linearly independent zero modes. We separately discuss the cases of the homogeneous Dirichlet boundary conditions, when the number of zero modes cannot exceed r, and the case of twisted boundary conditions, including the periodic and anti-periodic ones, when the number of zero modes is bounded above by 2r. In all cases the determinants with excluded zero eigenvalues can be expressed only in terms of the n zero modes and other r-n or 2r-n (depending on the boundary conditions) solutions of the homogeneous equation O h=0 , in the spirit of Gel’fand-Yaglom approach. In instanton calculations, the contribution of the zero modes is taken into account by introducing the so-called collective coordinates. We show that there is a remarkable cancellation of a factor (involving scalar products of zero modes) between the Jacobian of the transformation to the collective coordinates and the functional fluctuation determinant with excluded zero eigenvalues. This cancellation drastically simplifies instanton calculations when one uses our formulas.

Optimizing the inner loop of the gravitational force interaction on modern processors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Warren, Michael S

2010-12-08

We have achieved superior performance on multiple generations of the fastest supercomputers in the world with our hashed oct-tree N-body code (HOT), spanning almost two decades and garnering multiple Gordon Bell Prizes for significant achievement in parallel processing. Execution time for our N-body code is largely influenced by the force calculation in the inner loop. Improvements to the inner loop using SSE3 instructions has enabled the calculation of over 200 million gravitational interactions per second per processor on a 2.6 GHz Opteron, for a computational rate of over 7 Gflops in single precision (700/0 of peak). We obtain optimal performancemore » some processors (including the Cell) by decomposing the reciprocal square root function required for a gravitational interaction into a table lookup, Chebychev polynomial interpolation, and Newton-Raphson iteration, using the algorithm of Karp. By unrolling the loop by a factor of six, and using SPU intrinsics to compute on vectors, we obtain performance of over 16 Gflops on a single Cell SPE. Aggregated over the 8 SPEs on a Cell processor, the overall performance is roughly 130 Gflops. In comparison, the ordinary C version of our inner loop only obtains 1.6 Gflops per SPE with the spuxlc compiler.« less

The mass spectral density in quantitative time-of-flight mass spectrometry of polymers

NASA Astrophysics Data System (ADS)

Tate, Ranjeet S.; Ebeling, Dan; Smith, Lloyd M.

2001-03-01

Time-of-flight mass spectrometry (TOF-MS) is being increasingly used for the study of polymers, for example to obtain the distribution of molecular masses for polymer samples. Serious efforts have also been underway to use TOF-MS for DNA sequencing. In TOF-MS the data is obtained in the form of a time-series that represents the distribution in arrival times of ions of various m/z ratios. This time-series data is then converted to a "mass-spectrum" via a coordinate transformation from the arrival time (t) to the corresponding mass-to-charge ratio (m/z = const. t^2). In this transformation, it is important to keep in mind that spectra are distributions, or densities of weight +1, and thus do not transform as functions. To obtain the mass-spectral density, it is necessary to include a multiplicative factor of √m/z. Common commercial instruments do not take this factor into account. Dropping this factor has no effect on qualitative analysis (detection) or local quantitative measurements, since S/N or signal-to-baseline ratios are unaffected for peaks with small dispersions. However, there are serious consequences for general quantitative analyses. In DNA sequencing applications, loss of signal intensity is in part attributed to multiple charging; however, since the √m/z factor is not taken into account, this conclusion is based on an overestimate (by a factor of √z) of the relative amount of the multiply charged species. In the study of polymers, the normalized dispersion is underestimated by approximately (M_w/Mn -1)/2. In terms of M_w/Mn itself, for example, a M_w/M_n=1.5 calculated without the √m factor corresponds in fact to a M_w/M_n=1.88.

Clustering of risk factors for noncommunicable diseases in Brazilian adolescents: prevalence and correlates.

PubMed

Cureau, Felipe Vogt; Duarte, Paola; dos Santos, Daniela Lopes; Reichert, Felipe Fossati

2014-07-01

Few studies have investigated the prevalence and correlates of risk factors for noncommunicable diseases among Brazilian adolescents. We evaluated the clustering of risk factors and their associations with sociodemographic variables. We used a cross-sectional study carried out in 2011 comprising 1132 students aged 14-19 years from Santa Maria, Brazil. The cluster index was created as the sum of the risk factors. For the correlates analysis, a multinomial logistic regression was used. Furthermore, the observed/expected ratio was calculated. Prevalence of individual risk factors studied was as follows: 85.8% unhealthy diets, 53.5% physical inactivity, 31.3% elevated blood pressure, 23.9% overweight, 22.3% excessive drinking alcohol, and 8.6% smoking. Only 2.8% of the adolescents did not present any risk factor, while 21.7%, 40.9%, 23.1%, and 11.5% presented 1, 2, 3, and 4 or more risk factors, respectively. The most prevalent combination was between unhealthy diets and physical inactivity (observed/expected ratio =1.32; 95% CI: 1.16-1.49). Clustering of risk factors was directly associated with age and inversely associated with socioeconomic status. Clustering of risk factors for noncommunicable diseases is high in Brazilian adolescents. Preventive strategies are more likely to be successful if focusing on multiple risk factors, instead of a single one.

Calculation of low-Z impurity pellet induced fluxes of charge exchange neutral particles escaping from magnetically confined toroidal plasmas.

PubMed

Goncharov, P R; Ozaki, T; Sudo, S; Tamura, N; Tolstikhina, I Yu; Sergeev, V Yu

2008-10-01

Measurements of energy- and time-resolved neutral hydrogen and helium fluxes from an impurity pellet ablation cloud, referred to as pellet charge exchange or PCX experiments, can be used to study local fast ion energy distributions in fusion plasmas. The estimation of the local distribution function f(i)(E) of fast ions entering the cloud requires knowledge of both the fraction F(0)(E) of incident ions exiting the cloud as neutral atoms and the attenuation factor A(E,rho) describing the loss of fast atoms in the plasma. Determination of A(E,rho), in turn, requires the total stopping cross section sigma(loss) of neutral atoms in the plasma and the Jacobian reflecting the measurement geometry and the magnetic surface shape. The obtained functions F(0)(E) and A(E,rho) enter multiplicatively into the probability density for escaping neutral particle kinetic energy. A general calculation scheme has been developed and realized as a FORTRAN code, which is to be applied for the calculation of f(i)(E) from PCX experimental results obtained with low-Z impurity pellets.

Multiple-scattering model for inclusive proton production in heavy ion collisions

NASA Technical Reports Server (NTRS)

Cucinotta, Francis A.

1994-01-01

A formalism is developed for evaluating the momentum distribution for proton production in nuclear abrasion during heavy ion collisions using the Glauber multiple-scattering series. Several models for the one-body density matrix of nuclei are considered for performing numerical calculations. Calculations for the momentum distribution of protons in abrasion are compared with experimental data for inclusive proton production.

Calculation of Pareto-optimal solutions to multiple-objective problems using threshold-of-acceptability constraints

NASA Technical Reports Server (NTRS)

Giesy, D. P.

1978-01-01

A technique is presented for the calculation of Pareto-optimal solutions to a multiple-objective constrained optimization problem by solving a series of single-objective problems. Threshold-of-acceptability constraints are placed on the objective functions at each stage to both limit the area of search and to mathematically guarantee convergence to a Pareto optimum.

Morphology enabled dipole inversion (MEDI) from a single-angle acquisition: comparison with COSMOS in human brain imaging.

PubMed

Liu, Tian; Liu, Jing; de Rochefort, Ludovic; Spincemaille, Pascal; Khalidov, Ildar; Ledoux, James Robert; Wang, Yi

2011-09-01

Magnetic susceptibility varies among brain structures and provides insights into the chemical and molecular composition of brain tissues. However, the determination of an arbitrary susceptibility distribution from the measured MR signal phase is a challenging, ill-conditioned inverse problem. Although a previous method named calculation of susceptibility through multiple orientation sampling (COSMOS) has solved this inverse problem both theoretically and experimentally using multiple angle acquisitions, it is often impractical to carry out on human subjects. Recently, the feasibility of calculating the brain susceptibility distribution from a single-angle acquisition was demonstrated using morphology enabled dipole inversion (MEDI). In this study, we further improved the original MEDI method by sparsifying the edges in the quantitative susceptibility map that do not have a corresponding edge in the magnitude image. Quantitative susceptibility maps generated by the improved MEDI were compared qualitatively and quantitatively with those generated by calculation of susceptibility through multiple orientation sampling. The results show a high degree of agreement between MEDI and calculation of susceptibility through multiple orientation sampling, and the practicality of MEDI allows many potential clinical applications. Copyright © 2011 Wiley-Liss, Inc.

Computing the nucleon charge and axial radii directly at Q2=0 in lattice QCD

NASA Astrophysics Data System (ADS)

Hasan, Nesreen; Green, Jeremy; Meinel, Stefan; Engelhardt, Michael; Krieg, Stefan; Negele, John; Pochinsky, Andrew; Syritsyn, Sergey

2018-02-01

We describe a procedure for extracting momentum derivatives of nucleon matrix elements on the lattice directly at Q2=0 . This is based on the Rome method for computing momentum derivatives of quark propagators. We apply this procedure to extract the nucleon isovector magnetic moment and charge radius as well as the isovector induced pseudoscalar form factor at Q2=0 and the axial radius. For comparison, we also determine these quantities with the traditional approach of computing the corresponding form factors, i.e. GEv(Q2) and GMv(Q2) for the case of the vector current and GPv(Q2) and GAv(Q2) for the axial current, at multiple Q2 values followed by z -expansion fits. We perform our calculations at the physical pion mass using a 2HEX-smeared Wilson-clover action. To control the effects of excited-state contamination, the calculations were done at three source-sink separations and the summation method was used. The derivative method produces results consistent with those from the traditional approach but with larger statistical uncertainties especially for the isovector charge and axial radii.

The joint return period analysis of natural disasters based on monitoring and statistical modeling of multidimensional hazard factors.

PubMed

Liu, Xueqin; Li, Ning; Yuan, Shuai; Xu, Ning; Shi, Wenqin; Chen, Weibin

2015-12-15

As a random event, a natural disaster has the complex occurrence mechanism. The comprehensive analysis of multiple hazard factors is important in disaster risk assessment. In order to improve the accuracy of risk analysis and forecasting, the formation mechanism of a disaster should be considered in the analysis and calculation of multi-factors. Based on the consideration of the importance and deficiencies of multivariate analysis of dust storm disasters, 91 severe dust storm disasters in Inner Mongolia from 1990 to 2013 were selected as study cases in the paper. Main hazard factors from 500-hPa atmospheric circulation system, near-surface meteorological system, and underlying surface conditions were selected to simulate and calculate the multidimensional joint return periods. After comparing the simulation results with actual dust storm events in 54years, we found that the two-dimensional Frank Copula function showed the better fitting results at the lower tail of hazard factors and that three-dimensional Frank Copula function displayed the better fitting results at the middle and upper tails of hazard factors. However, for dust storm disasters with the short return period, three-dimensional joint return period simulation shows no obvious advantage. If the return period is longer than 10years, it shows significant advantages in extreme value fitting. Therefore, we suggest the multivariate analysis method may be adopted in forecasting and risk analysis of serious disasters with the longer return period, such as earthquake and tsunami. Furthermore, the exploration of this method laid the foundation for the prediction and warning of other nature disasters. Copyright © 2015 Elsevier B.V. All rights reserved.

[Life satisfaction and related socio-demographic factors during female midlife].

PubMed

Cuadros, José Luis; Pérez-Roncero, Gonzalo R; López-Baena, María Teresa; Cuadros-Celorrio, Angela M; Fernández-Alonso, Ana María

2014-01-01

To assess life satisfaction and related factors in middle-aged Spanish women. This was a cross-sectional study including 235 women aged 40 to 65, living in Granada (Spain), healthy companions of patients visiting the obstetrics and gynecology clinics. They completed the Diener Satisfaction with Life Scale, the Menopause Rating Scale, the Perceived Stress Scale, the Insomnia Severity Index and a sociodemographic questionnaire containing personal and partner data. Internal consistency of each tool was also calculated. Almost two-thirds (61.3%) of the women were postmenopausal, and 43.8% had abdominal obesity, 36.6% had insomnia, 18.7% had poor menopause-related quality of life, 31.9% performed regular exercise, and 5.1% had severe financial problems. Life satisfaction showed significant positive correlations (Spearman's test) with female and male age, and inverse correlations with menopause-related quality of life, perceived stress and insomnia. In the multiple linear regression analysis, high life satisfaction is positively correlated with having a partner who performed exercise, and inversely with having work problems, perceived stress and the suspicion of partner infidelity. These factors explained 40% of the variance of the multiple regression analysis for life satisfaction in middle-aged women. Life satisfaction is a construct related to perceived stress, work problems, and having a partner, while aspects of menopause and general health had no significant influence. Copyright © 2014 Elsevier España, S.L.U. All rights reserved.

Contribution of indoor and outdoor nitrogen dioxide to indoor air quality of wayside shops.

PubMed

Shuai, Jianfei; Yang, Wonho; Ahn, Hogi; Kim, Sunshin; Lee, Seokyong; Yoon, Sung-Uk

2013-06-01

Indoor nitrogen dioxide (NO₂) concentration is an important factor for personal exposure despite the wide distribution of its sources. Exposure to NO₂ may produce adverse health effects. The aims of this study were to characterize the indoor air quality of wayside shops using multiple NO₂ measurements, and to estimate the contribution of outdoor NO₂ sources such as vehicle emission to indoor air quality. Daily indoor and outdoor NO₂ concentrations were measured for 21 consecutive days in wayside shops (5 convenience stores, 5 coffee shops, and 5 restaurants). Contributions of outdoor NO₂ sources to indoor air quality were calculated with penetration factors and source strength factors by indoor mass balance model in winter and summer, respectively. Most wayside shops had significant differences in indoor and outdoor NO₂ concentrations both in winter and in summer. Indoor NO₂ concentrations in restaurants were twice more than those in convenience stores and coffee shops in winter. While outdoor NO₂ contributions in indoor convenience stores and coffee shops were dominant, indoor NO₂ contributions were dominant in restaurants. These could be explained that indoor NO₂ sources such as gas range and smoking mainly affect indoor concentrations comparing to outdoor sources such as vehicle emission. The indoor mass balance model by multiple measurements suggests that quantitative contribution of outdoor air on indoor air quality might be estimated without measurements of ventilation, indoor generation and decay rate.

Anabolic and catabolic biomarkers as predictors of muscle strength decline: the InCHIANTI study.

PubMed

Stenholm, Sari; Maggio, Marcello; Lauretani, Fulvio; Bandinelli, Stefania; Ceda, Gian Paolo; Di Iorio, Angelo; Giallauria, Francesco; Guralnik, Jack M; Ferrucci, Luigi

2010-02-01

Poor muscle strength is a major public health concern in older persons, predisposing to functional limitations, increased fall risk, and higher mortality. Understanding risk factors for muscle strength decline may offer opportunities for prevention and treatment. One of the possible causes of muscle strength decline is imbalance between catabolic and anabolic signaling. This study aims to examine whether high levels of multiple catabolic and low levels of multiple anabolic biomarkers predict accelerated decline of muscle strength. In a representative sample of 716 men and women aged >or=65 years in the InCHIANTI study we measured C-reactive protein, interleukin-6 (IL-6), IL-1 receptor antagonist (IL-1RA), tumor necrosis factor-alpha receptor 1 as well as dehydroepiandrosterone sulfate (DHEA-S), insulin-like growth factor-1, and bioavailable testosterone. Biomarker values were divided into tertiles and the numbers of catabolic/anabolic biomarkers in the highest/lowest tertile were calculated. Hand-grip strength was measured at baseline and 3- and 6-year follow up. In adjusted linear mixed models, higher concentration of IL-6 (p = 0.02) and IL-1RA (p = 0.04) as well as lower levels of DHEA-S (p = 0.01) predicted muscle strength decline. After combining all inflammatory markers, the rate of decline in grip strength was progressively greater with the increasing number of dysregulated catabolic biomarkers (p = 0.01). No effect on accelerated muscle strength decline was seen according to number of dysregulated anabolic hormones. Having multiple elevated catabolic biomarkers is a better predictor of muscle strength decline than a single biomarker alone, suggesting that a catabolic dysregulation is at the core of the mechanism leading to muscle strength decline with aging.

Anabolic and Catabolic Biomarkers As Predictors of Muscle Strength Decline: The InCHIANTI Study

PubMed Central

Maggio, Marcello; Lauretani, Fulvio; Bandinelli, Stefania; Ceda, Gian Paolo; Di Iorio, Angelo; Giallauria, Francesco; Guralnik, Jack M.; Ferrucci, Luigi

2010-01-01

Abstract Background Poor muscle strength is a major public health concern in older persons, predisposing to functional limitations, increased fall risk, and higher mortality. Understanding risk factors for muscle strength decline may offer opportunities for prevention and treatment. One of the possible causes of muscle strength decline is imbalance between catabolic and anabolic signaling. This study aims to examine whether high levels of multiple catabolic and low levels of multiple anabolic biomarkers predict accelerated decline of muscle strength. Methods In a representative sample of 716 men and women aged ≥65 years in the InCHIANTI study we measured C-reactive protein, interleukin-6 (IL-6), IL-1 receptor antagonist (IL-1RA), tumor necrosis factor-α receptor 1 as well as dehydroepiandrosterone sulfate (DHEA-S), insulin-like growth factor-1, and bioavailable testosterone. Biomarker values were divided into tertiles and the numbers of catabolic/anabolic biomarkers in the highest/lowest tertile were calculated. Hand-grip strength was measured at baseline and 3- and 6-year follow up. Results In adjusted linear mixed models, higher concentration of IL-6 (p = 0.02) and IL-1RA (p = 0.04) as well as lower levels of DHEA-S (p = 0.01) predicted muscle strength decline. After combining all inflammatory markers, the rate of decline in grip strength was progressively greater with the increasing number of dysregulated catabolic biomarkers (p = 0.01). No effect on accelerated muscle strength decline was seen according to number of dysregulated anabolic hormones. Conclusions Having multiple elevated catabolic biomarkers is a better predictor of muscle strength decline than a single biomarker alone, suggesting that a catabolic dysregulation is at the core of the mechanism leading to muscle strength decline with aging. PMID:20230273

Metal poisons for criticality in waste streams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williamson, T.G.; Goslen, A.Q.

1996-12-31

Many of the wastes from processing fissile materials contain metals that may serve as neutron poisons. It would be advantageous to the criticality evaluation of these wastes to demonstrate that the poisons remain with the fissile materials and to demonstrate an always safe poison-to-fissile ratio. The first task, demonstrating that the materials stay together, is the job of the chemist; the second, calculating an always safe ratio, is an object of this paper. In an earlier study, the authors demonstrated safe ratios for iron, manganese, and chromium oxides to {sup 235}U. In these studies, the Hansen-Roach 16-group cross sections weremore » used with the Savannah River site code HRXN. Multiplication factors were computed, and safe ratios were defined such that the adjusted neutron multiplication factors (k values) were <0.95. These safe weight ratios were Fe:{sup 235}U - 77:1; Mn:{sup 235}U - 30:1; and Cr:{sup 235}U - 52:1. Palmer has shown that for certain mixtures of aluminum, iron, and zirconium with {sup 235}U, the computed infinite multiplication factors may differ by as much as 20% with different cross sections and processing systems. Parks et al. have further studied these mixtures and state, {open_quotes}...these metal/uranium mixtures are very sensitive to the metal cross-section data in the intermediate-energy range and the processing methods that are used.{close_quotes} They conclude with a call for more experimental data. The purpose of this study is to reexamine earlier work with cross sections and processing codes used at Westinghouse Savannah River Company today. This study will focus on {sup 235}U mixtures with iron, manganese and chromium. Sodium will be included in the list of poisons because it is abundant in many of the waste materials.« less

Investigating Mixture Interactions of Astringent Stimuli Using the Isobole Approach

PubMed Central

Fleming, Erin E.; Ziegler, Gregory R.

2016-01-01

Abstract Astringents (alum, malic acid, tannic acid) representing 3 broad classes (multivalent salts, organic acids, and polyphenols) were characterized alone, and as 2- and 3-component mixtures using isoboles. In experiment 1, participants rated 7 attributes (“astringency,” the sub-qualities “drying,” “roughing,” and “puckering,” and the side tastes “bitterness,” “sourness,” and “sweetness”) using direct scaling. Quality specific power functions were calculated for each stimulus. In experiment 2, the same participants characterized 2- and 3-component mixtures. Multiple factor analysis (MFA) and hierarchical clustering on attribute ratings across stimuli indicate “astringency” is highly related to “bitterness” as well as “puckering,” and the subqualities “drying” and “roughing” are somewhat redundant. Moreover, power functions were used to calculate indices of interaction (I) for each attribute/mixture combination. For “astringency,” there was evidence of antagonism, regardless of the type of mixture. Conversely, for subqualities, the pattern of interaction depended on the mixture type. Alum/tannic acid and tannic acid/malic acid mixtures showed evidence of synergy for “drying” and “roughing”; alum/malic acid mixtures showed evidence of antagonism for “drying,” “roughing,” and “puckering.” Collectively, these data clarify some semantic ambiguity regarding astringency and its subqualities, as well as the nature of interactions of among different types of astringents. Present data are not inconsistent with the idea that astringency arises from multiple mechanisms, although it remains to be determined whether the synergy observed here might reflect simultaneous activation of these multiple mechanisms. PMID:27252355

Impact of reproductive efficiency over time and mare financial value on economic returns among Thoroughbred mares in central Kentucky.

PubMed

Bosh, K A; Powell, D; Neibergs, J S; Shelton, B; Zent, W

2009-12-01

There have been no studies reporting the impact of reproductive efficiency and mare financial value on economic returns. To explore the economic consequences of differences in reproductive efficiency over time in the Thoroughbred mare. Complete production records for 1176 mares were obtained. Production history and drift in foaling date were calculated. Multiple logistic regression was used to identify factors influencing the probability of producing a registered foal in 2005. The 'net present value' and 'internal rate of return' were calculated for economic scenarios involving different initial mare financial values, levels of reproductive efficiency, and durations of investment. Among mares that did not produce a foal every year (63%), the mean time before failing to produce a registered foal was 3.4 years. The majority of mares drifted later in their foaling dates in subsequent foaling seasons. Increasing mare age, foaling after 1st April, needing to be mated multiple times during the season, and producing a lower number of foals in continuous sequence during previous years decreased the probability of producing a registered foal. Over a 7 year investment period, live foals must be produced in all but one year to yield a positive financial return. Profitability was highest among mares of greatest financial value. Mares are long-term investments due to the extended period before there is a return on the investment. Improving our understanding of mare, stallion and management factors that affect the likelihood of producing a live foal are critical to ensuring a positive financial return. Additional work is needed to test the robustness of the study's conclusions when the cost and revenue assumptions are varied. This information can assist in assessing mare profitability and developing management strategies to maximise profitability.

Solution structure of the DNA-binding domain of the heat shock transcription factor determined by multidimensional heteronuclear magnetic resonance spectroscopy.

PubMed Central

Damberger, F. F.; Pelton, J. G.; Harrison, C. J.; Nelson, H. C.; Wemmer, D. E.

1994-01-01

The solution structure of the 92-residue DNA-binding domain of the heat shock transcription factor from Kluyveromyces lactis has been determined using multidimensional NMR methods. Three-dimensional (3D) triple resonance, 1H-13C-13C-1H total correlation spectroscopy, and 15N-separated total correlation spectroscopy-heteronuclear multiple quantum correlation experiments were used along with various 2D spectra to make nearly complete assignments for the backbone and side-chain 1H, 15N, and 13C resonances. Five-hundred eighty-three NOE constraints identified in 3D 13C- and 15N-separated NOE spectroscopy (NOESY)-heteronuclear multiple quantum correlation spectra and a 4-dimensional 13C/13C-edited NOESY spectrum, along with 35 phi, 9 chi 1, and 30 hydrogen bond constraints, were used to calculate 30 structures by hybrid distance geometry/stimulated annealing protocol, of which 24 were used for structural comparison. The calculations revealed that a 3-helix bundle packs against a small 4-stranded antiparallel beta-sheet. The backbone RMS deviation (RMSD) for the family of structures was 1.03 +/- 0.19 A with respect to the average structure. The topology is analogous to that of the C-terminal domain of the catabolite gene activator protein and appears to be in the helix-turn-helix family of DNA-binding proteins. The overall fold determined by the NMR data is consistent with recent crystallographic work on this domain (Harrison CJ, Bohm AA, Nelson HCM, 1994, Science 263:224) as evidenced by RMSD between backbone atoms in the NMR and X-ray structures of 1.77 +/- 0.20 A. Several differences were identified some of which may be due to protein-protein interactions in the crystal. PMID:7849597

Superlattice formation lifting degeneracy protected by nonsymmorphic symmetry through a metal-insulator transition in RuAs

NASA Astrophysics Data System (ADS)

Kotegawa, Hisashi; Takeda, Keiki; Kuwata, Yoshiki; Hayashi, Junichi; Tou, Hideki; Sugawara, Hitoshi; Sakurai, Takahiro; Ohta, Hitoshi; Harima, Hisatomo

2018-05-01

A single crystal of RuAs obtained with the Bi-flux method shows obvious successive metal-insulator transitions at TMI 1˜255 K and TMI 2˜195 K. The x-ray diffraction measurement reveals the formation of a superlattice of 3 ×3 ×3 of the original unit cell below TMI 2, accompanied by a change of the crystal system from the orthorhombic structure to the monoclinic one. Simple dimerization of the Ru ions is not seen in the ground state. The multiple As sites observed in the nuclear quadrupole resonance spectrum also demonstrate the formation of the superlattice in the ground state, which is clarified to be nonmagnetic. The divergence in 1 /T1 at TMI 1 shows that a symmetry lowering by the metal-insulator transition is accompanied by strong critical fluctuations of some degrees of freedom. Using the structural parameters in the insulating state, the first-principles calculation reproduces successfully the reasonable size of nuclear quadrupole frequencies νQ for the multiple As sites, ensuring the high validity of the structural parameters. The calculation also gives a remarkable suppression in the density of states near the Fermi level, although the gap opening is insufficient. A coupled modulation of the calculated Ru d -electron numbers and the crystal structure proposes the formation of a charge density wave in RuAs. Some lacking factors remain, but it is shown that a lifting of degeneracy protected by the nonsymmorphic symmetry through the superlattice formation is a key ingredient for the metal-insulator transition in RuAs.

Differences Between Gait on Stairs and Flat Surfaces in Relation to Fall Risk and Future Falls.

PubMed

Wang, Kejia; Delbaere, Kim; Brodie, Matthew A D; Lovell, Nigel H; Kark, Lauren; Lord, Stephen R; Redmond, Stephen J

2017-11-01

We used body-worn inertial sensors to quantify differences in semi-free-living gait between stairs and on normal flat ground in older adults, and investigated the utility of assessing gait on these terrains for predicting the occurrence of multiple falls. Eighty-two community-dwelling older adults wore two inertial sensors, on the lower back and the right ankle, during several bouts of walking on flat surfaces and up and down stairs, in between rests and activities of daily living. Derived from the vertical acceleration at the lower back, step rate was calculated from the signal's fundamental frequency. Step rate variability was the width of this fundamental frequency peak from the signal's power spectral density. Movement vigor was calculated at both body locations from the signal variance. Partial Spearman correlations between gait parameters and physiological fall risk factors (components from the Physiological Profile Assessment) were calculated while controlling for age and gender. Overall, anteroposterior vigor at the lower back in stair descent was lower in subjects with longer reaction times. Older adults walked more slowly on stairs, but they were not significantly slower on flat surfaces. Using logistic regression, faster step rate in stair descent was associated with multiple prospective falls over 12 months. No significant associations were shown from gait parameters derived during walking upstairs or on flat surfaces. These results suggest that stair descent gait may provide more insight into fall risk than regular walking and stair ascent, and that further sensor-based investigation into unsupervised gait on different terrains would be valuable.

From Excessive Journal Self-Cites to Citation Stacking: Analysis of Journal Self-Citation Kinetics in Search for Journals, Which Boost Their Scientometric Indicators.

PubMed

Heneberg, Petr

2016-01-01

Bibliometric indicators increasingly affect careers, funding, and reputation of individuals, their institutions and journals themselves. In contrast to author self-citations, little is known about kinetics of journal self-citations. Here we hypothesized that they may show a generalizable pattern within particular research fields or across multiple fields. We thus analyzed self-cites to 60 journals from three research fields (multidisciplinary sciences, parasitology, and information science). We also hypothesized that the kinetics of journal self-citations and citations received from other journals of the same publisher may differ from foreign citations. We analyzed the journals published the American Association for the Advancement of Science, Nature Publishing Group, and Editura Academiei Române. We found that although the kinetics of journal self-cites is generally faster compared to foreign cites, it shows some field-specific characteristics. Particularly in information science journals, the initial increase in a share of journal self-citations during post-publication year 0 was completely absent. Self-promoting journal self-citations of top-tier journals have rather indirect but negligible direct effects on bibliometric indicators, affecting just the immediacy index and marginally increasing the impact factor itself as long as the affected journals are well established in their fields. In contrast, other forms of journal self-citations and citation stacking may severely affect the impact factor, or other citation-based indices. We identified here a network consisting of three Romanian physics journals Proceedings of the Romanian Academy, Series A, Romanian Journal of Physics, and Romanian Reports in Physics, which displayed low to moderate ratio of journal self-citations, but which multiplied recently their impact factors, and were mutually responsible for 55.9%, 64.7% and 63.3% of citations within the impact factor calculation window to the three journals, respectively. They did not receive nearly any network self-cites prior impact factor calculation window, and their network self-cites decreased sharply after the impact factor calculation window. Journal self-citations and citation stacking requires increased attention and elimination from citation indices.

From Excessive Journal Self-Cites to Citation Stacking: Analysis of Journal Self-Citation Kinetics in Search for Journals, Which Boost Their Scientometric Indicators

PubMed Central

2016-01-01

Bibliometric indicators increasingly affect careers, funding, and reputation of individuals, their institutions and journals themselves. In contrast to author self-citations, little is known about kinetics of journal self-citations. Here we hypothesized that they may show a generalizable pattern within particular research fields or across multiple fields. We thus analyzed self-cites to 60 journals from three research fields (multidisciplinary sciences, parasitology, and information science). We also hypothesized that the kinetics of journal self-citations and citations received from other journals of the same publisher may differ from foreign citations. We analyzed the journals published the American Association for the Advancement of Science, Nature Publishing Group, and Editura Academiei Române. We found that although the kinetics of journal self-cites is generally faster compared to foreign cites, it shows some field-specific characteristics. Particularly in information science journals, the initial increase in a share of journal self-citations during post-publication year 0 was completely absent. Self-promoting journal self-citations of top-tier journals have rather indirect but negligible direct effects on bibliometric indicators, affecting just the immediacy index and marginally increasing the impact factor itself as long as the affected journals are well established in their fields. In contrast, other forms of journal self-citations and citation stacking may severely affect the impact factor, or other citation-based indices. We identified here a network consisting of three Romanian physics journals Proceedings of the Romanian Academy, Series A, Romanian Journal of Physics, and Romanian Reports in Physics, which displayed low to moderate ratio of journal self-citations, but which multiplied recently their impact factors, and were mutually responsible for 55.9%, 64.7% and 63.3% of citations within the impact factor calculation window to the three journals, respectively. They did not receive nearly any network self-cites prior impact factor calculation window, and their network self-cites decreased sharply after the impact factor calculation window. Journal self-citations and citation stacking requires increased attention and elimination from citation indices. PMID:27088862

Factors associated with developing a fear of falling in subjects with primary open-angle glaucoma.

PubMed

Adachi, Sayaka; Yuki, Kenya; Awano-Tanabe, Sachiko; Ono, Takeshi; Shiba, Daisuke; Murata, Hiroshi; Asaoka, Ryo; Tsubota, Kazuo

2018-02-13

To investigate the relationship between clinical risk factors, including visual field (VF) defects and visual acuity, and a fear of falling, among patients with primary open-angle glaucoma (POAG). All participants answered the following question at a baseline ophthalmic examination: Are you afraid of falling? The same question was then answered every 12 months for 3 years. A binocular integrated visual field was calculated by merging a patient's monocular Humphrey field analyzer VFs, using the 'best sensitivity' method. The means of total deviation values in the whole, superior peripheral, superior central, inferior central, and inferior peripheral VFs were calculated. The relationship between these mean VF measurements, and various clinical factors, against patients' baseline fear of falling and future fear of falling was analyzed using multiple logistic regression. Among 392 POAG subjects, 342 patients (87.2%) responded to the fear of falling question at least twice in the 3 years study period. The optimal regression model for patients' baseline fear of falling included age, gender, mean of total deviation values in the inferior peripheral VF and number of previous falls. The optimal regression equation for future fear of falling included age, gender, mean of total deviation values in the inferior peripheral VF and number of previous falls. Defects in the inferior peripheral VF area are significantly related to the development of a fear of falling.

Rational reduction of periodic propagators for off-period observations.

PubMed

Blanton, Wyndham B; Logan, John W; Pines, Alexander

2004-02-01

Many common solid-state nuclear magnetic resonance problems take advantage of the periodicity of the underlying Hamiltonian to simplify the computation of an observation. Most of the time-domain methods used, however, require the time step between observations to be some integer or reciprocal-integer multiple of the period, thereby restricting the observation bandwidth. Calculations of off-period observations are usually reduced to brute force direct methods resulting in many demanding matrix multiplications. For large spin systems, the matrix multiplication becomes the limiting step. A simple method that can dramatically reduce the number of matrix multiplications required to calculate the time evolution when the observation time step is some rational fraction of the period of the Hamiltonian is presented. The algorithm implements two different optimization routines. One uses pattern matching and additional memory storage, while the other recursively generates the propagators via time shifting. The net result is a significant speed improvement for some types of time-domain calculations.

Chronic beryllium disease and cancer risk estimates with uncertainty for beryllium released to the air from the Rocky Flats Plant.

PubMed Central

McGavran, P D; Rood, A S; Till, J E

1999-01-01

Beryllium was released into the air from routine operations and three accidental fires at the Rocky Flats Plant (RFP) in Colorado from 1958 to 1989. We evaluated environmental monitoring data and developed estimates of airborne concentrations and their uncertainties and calculated lifetime cancer risks and risks of chronic beryllium disease to hypothetical receptors. This article discusses exposure-response relationships for lung cancer and chronic beryllium disease. We assigned a distribution to cancer slope factor values based on the relative risk estimates from an occupational epidemiologic study used by the U.S. Environmental Protection Agency (EPA) to determine the slope factors. We used the regional atmospheric transport code for Hanford emission tracking atmospheric transport model for exposure calculations because it is particularly well suited for long-term annual-average dispersion estimates and it incorporates spatially varying meteorologic and environmental parameters. We accounted for model prediction uncertainty by using several multiplicative stochastic correction factors that accounted for uncertainty in the dispersion estimate, the meteorology, deposition, and plume depletion. We used Monte Carlo techniques to propagate model prediction uncertainty through to the final risk calculations. We developed nine exposure scenarios of hypothetical but typical residents of the RFP area to consider the lifestyle, time spent outdoors, location, age, and sex of people who may have been exposed. We determined geometric mean incremental lifetime cancer incidence risk estimates for beryllium inhalation for each scenario. The risk estimates were < 10(-6). Predicted air concentrations were well below the current reference concentration derived by the EPA for beryllium sensitization. Images Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 PMID:10464074

Dosimetry of 3 CBCT devices for oral and maxillofacial radiology: CB Mercuray, NewTom 3G and i-CAT.

PubMed

Ludlow, J B; Davies-Ludlow, L E; Brooks, S L; Howerton, W B

2006-07-01

Cone beam computed tomography (CBCT), which provides a lower dose, lower cost alternative to conventional CT, is being used with increasing frequency in the practice of oral and maxillofacial radiology. This study provides comparative measurements of effective dose for three commercially available, large (12'') field-of-view (FOV), CBCT units: CB Mercuray, NewTom 3G and i-CAT. Thermoluminescent dosemeters (TLDs) were placed at 24 sites throughout the layers of the head and neck of a tissue-equivalent human skull RANDO phantom. Depending on availability, the 12'' FOV and smaller FOV scanning modes were used with similar phantom positioning geometry for each CBCT unit. Radiation weighted doses to individual organs were summed using 1990 (E(1990)) and proposed 2005 (E(2005 draft)) ICRP tissue weighting factors to calculate two measures of whole-body effective dose. Dose as a multiple of a representative panoramic radiography dose was also calculated. For repeated runs dosimetry was generally reproducible within 2.5%. Calculated doses in microSv [corrected] (E(1990), E(2005 draft)) were NewTom3G (45, 59), i-CAT (135, 193) and CB Mercuray (477, 558). These are 4 to 42 times greater than comparable panoramic examination doses (6.3 microSv [corrected] 13.3 mSv). Reductions in dose were seen with reduction in field size and mA and kV technique factors. CBCT dose varies substantially depending on the device, FOV and selected technique factors. Effective dose detriment is several to many times higher than conventional panoramic imaging and an order of magnitude or more less than reported doses for conventional CT.

Multiple testing and power calculations in genetic association studies.

PubMed

So, Hon-Cheong; Sham, Pak C

2011-01-01

Modern genetic association studies typically involve multiple single-nucleotide polymorphisms (SNPs) and/or multiple genes. With the development of high-throughput genotyping technologies and the reduction in genotyping cost, investigators can now assay up to a million SNPs for direct or indirect association with disease phenotypes. In addition, some studies involve multiple disease or related phenotypes and use multiple methods of statistical analysis. The combination of multiple genetic loci, multiple phenotypes, and multiple methods of evaluating associations between genotype and phenotype means that modern genetic studies often involve the testing of an enormous number of hypotheses. When multiple hypothesis tests are performed in a study, there is a risk of inflation of the type I error rate (i.e., the chance of falsely claiming an association when there is none). Several methods for multiple-testing correction are in popular use, and they all have strengths and weaknesses. Because no single method is universally adopted or always appropriate, it is important to understand the principles, strengths, and weaknesses of the methods so that they can be applied appropriately in practice. In this article, we review the three principle methods for multiple-testing correction and provide guidance for calculating statistical power.

Measurement of charm and beauty production at central rapidity versus charged-particle multiplicity in proton-proton collisions at $$ \\sqrt{s}=7 $$ TeV

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adam, J.

Prompt D meson and non-prompt J/ψ yields are studied as a function of the multiplicity of charged particles produced in inelastic proton-proton collisions at a centre-of-mass energy ofmore » $$ \\sqrt{s}=7 $$ TeV. The results are reported as a ratio between yields in a given multiplicity interval normalised to the multiplicity-integrated ones (relative yields). They are shown as a function of the multiplicity of charged particles normalised to the average value for inelastic collisions (relative charged-particle multiplicity). D 0, D + and D *+ mesons are measured in five p T intervals from 1 GeV/c to 20 GeV/c and for |y| < 0.5 via their hadronic decays. The D-meson relative yield is found to increase with increasing charged-particle multiplicity. For events with multiplicity six times higher than the average multiplicity of inelastic collisions, a yield enhancement of a factor about 15 relative to the multiplicity-integrated yield in inelastic collisions is observed. The yield enhancement is independent of transverse momentum within the uncertainties of the measurement. The D 0-meson relative yield is also measured as a function of the relative multiplicity at forward pseudo-rapidity. The non-prompt J/ψ, i.e. the B hadron, contribution to the inclusive J/ψ production is measured in the di-electron decay channel at central rapidity. It is evaluated for p T > 1.3 GeV/c and |y| < 0.9, and extrapolated to p T > 0. The fraction of non-prompt J/ψ in the inclusive J/ψ yields shows no dependence on the charged-particle multiplicity at central rapidity. Charm and beauty hadron relative yields exhibit a similar increase with increasing charged-particle multiplicity. Finally, the measurements are compared to PYTHIA 8, EPOS 3 and percolation calculations.« less

Measurement of charm and beauty production at central rapidity versus charged-particle multiplicity in proton-proton collisions at $$ \\sqrt{s}=7 $$ TeV

DOE PAGES

Adam, J.

2015-09-22

Prompt D meson and non-prompt J/ψ yields are studied as a function of the multiplicity of charged particles produced in inelastic proton-proton collisions at a centre-of-mass energy ofmore » $$ \\sqrt{s}=7 $$ TeV. The results are reported as a ratio between yields in a given multiplicity interval normalised to the multiplicity-integrated ones (relative yields). They are shown as a function of the multiplicity of charged particles normalised to the average value for inelastic collisions (relative charged-particle multiplicity). D 0, D + and D *+ mesons are measured in five p T intervals from 1 GeV/c to 20 GeV/c and for |y| < 0.5 via their hadronic decays. The D-meson relative yield is found to increase with increasing charged-particle multiplicity. For events with multiplicity six times higher than the average multiplicity of inelastic collisions, a yield enhancement of a factor about 15 relative to the multiplicity-integrated yield in inelastic collisions is observed. The yield enhancement is independent of transverse momentum within the uncertainties of the measurement. The D 0-meson relative yield is also measured as a function of the relative multiplicity at forward pseudo-rapidity. The non-prompt J/ψ, i.e. the B hadron, contribution to the inclusive J/ψ production is measured in the di-electron decay channel at central rapidity. It is evaluated for p T > 1.3 GeV/c and |y| < 0.9, and extrapolated to p T > 0. The fraction of non-prompt J/ψ in the inclusive J/ψ yields shows no dependence on the charged-particle multiplicity at central rapidity. Charm and beauty hadron relative yields exhibit a similar increase with increasing charged-particle multiplicity. Finally, the measurements are compared to PYTHIA 8, EPOS 3 and percolation calculations.« less

Multiple Myeloma and Glyphosate Use: A Re-Analysis of US Agricultural Health Study (AHS) Data

PubMed Central

Sorahan, Tom

2015-01-01

A previous publication of 57,311 pesticide applicators enrolled in the US Agricultural Health Study (AHS) produced disparate findings in relation to multiple myeloma risks in the period 1993–2001 and ever-use of glyphosate (32 cases of multiple myeloma in the full dataset of 54,315 applicators without adjustment for other variables: rate ratio (RR) 1.1, 95% confidence interval (CI) 0.5 to 2.4; 22 cases of multiple myeloma in restricted dataset of 40,719 applicators with adjustment for other variables: RR 2.6, 95% CI 0.7 to 9.4). It seemed important to determine which result should be preferred. RRs for exposed and non-exposed subjects were calculated using Poisson regression; subjects with missing data were not excluded from the main analyses. Using the full dataset adjusted for age and gender the analysis produced a RR of 1.12 (95% CI 0.50 to 2.49) for ever-use of glyphosate. Additional adjustment for lifestyle factors and use of ten other pesticides had little effect (RR 1.24, 95% CI 0.52 to 2.94). There were no statistically significant trends for multiple myeloma risks in relation to reported cumulative days (or intensity weighted days) of glyphosate use. The doubling of risk reported previously arose from the use of an unrepresentative restricted dataset and analyses of the full dataset provides no convincing evidence in the AHS for a link between multiple myeloma risk and glyphosate use. PMID:25635915

Pitfalls in interpretation of CT-values of RT-PCR in children with acute respiratory tract infections.

PubMed

Wishaupt, Jérôme O; Ploeg, Tjeerd van der; Smeets, Leo C; Groot, Ronald de; Versteegh, Florens G A; Hartwig, Nico G

2017-05-01

The relation between viral load and disease severity in childhood acute respiratory tract infections (ARI) is not fully understood. To assess the clinical relevance of the relation between viral load, determined by cycle threshold (CT) value of real-time reverse transcription-polymerase chain reaction assays and disease severity in children with single- and multiple viral ARI. 582 children with ARI were prospectively followed and tested for 15 viruses. Correlations were calculated between CT values and clinical parameters. In single viral ARI, statistically significant correlations were found between viral loads of Respiratory Syncytial Virus (RSV) and hospitalization and between viral loads of Human Coronavirus (HCoV) and a disease severity score. In multiple-viral ARI, statistically significant correlations between viral load and clinical parameters were found. In RSV-Rhinovirus (RV) multiple infections, a low viral load of RV was correlated with a high length of hospital stay and a high duration of extra oxygen use. The mean CT value for RV, HCoV and Parainfluenza virus was significantly lower in single- versus multiple infections. Although correlations between CT values and clinical parameters in patients with single and multiple viral infection were found, the clinical importance of these findings is limited because individual differences in host-, viral and laboratory factors complicate the interpretation of statistically significant findings. In multiple infections, viral load cannot be used to differentiate between disease causing virus and innocent bystanders. Copyright © 2017 Elsevier B.V. All rights reserved.

Multiple myeloma and glyphosate use: a re-analysis of US Agricultural Health Study (AHS) data.

PubMed

Sorahan, Tom

2015-01-28

A previous publication of 57,311 pesticide applicators enrolled in the US Agricultural Health Study (AHS) produced disparate findings in relation to multiple myeloma risks in the period 1993-2001 and ever-use of glyphosate (32 cases of multiple myeloma in the full dataset of 54,315 applicators without adjustment for other variables: rate ratio (RR) 1.1, 95% confidence interval (CI) 0.5 to 2.4; 22 cases of multiple myeloma in restricted dataset of 40,719 applicators with adjustment for other variables: RR 2.6, 95% CI 0.7 to 9.4). It seemed important to determine which result should be preferred. RRs for exposed and non-exposed subjects were calculated using Poisson regression; subjects with missing data were not excluded from the main analyses. Using the full dataset adjusted for age and gender the analysis produced a RR of 1.12 (95% CI 0.50 to 2.49) for ever-use of glyphosate. Additional adjustment for lifestyle factors and use of ten other pesticides had little effect (RR 1.24, 95% CI 0.52 to 2.94). There were no statistically significant trends for multiple myeloma risks in relation to reported cumulative days (or intensity weighted days) of glyphosate use. The doubling of risk reported previously arose from the use of an unrepresentative restricted dataset and analyses of the full dataset provides no convincing evidence in the AHS for a link between multiple myeloma risk and glyphosate use.

Media effects in modulating the conformational equilibrium of a model compound for tumor necrosis factor converting enzyme inhibition

NASA Astrophysics Data System (ADS)

Banchelli, Martina; Guardiani, Carlo; Sandberg, Robert B.; Menichetti, Stefano; Procacci, Piero; Caminati, Gabriella

2015-07-01

Small-molecule inhibitors of Tumor Necrosis Factor α Converting Enzyme (TACE) are a promising therapeutic tool for Rheumatoid Arthritis, Multiple Sclerosis and other autoimmune diseases. Here we report on an extensive chemical-physical analysis of the media effects in modulating the conformational landscape of MBET306, the common scaffold and a synthetic precursor of a family of recently discovered tartrate-based TACE inhibitors. The structural features of this molecule with potential pharmaceutical applications have been disclosed by interpreting extensive photophysical measurements in various solvents with the aid of enhanced sampling molecular dynamics simulations and time dependent density functional calculations. Using a combination of experimental and computational techniques, the paper provides a general protocol for studying the structure in solution of molecular systems characterized by the existence of conformational metastable states.

Finding Multiple Internal Rates of Return for a Project with Non-Conventional Cash Flows: Utilizing Popular Financial/Graphing Calculators and Spreadsheet Software

ERIC Educational Resources Information Center

Chen, Jeng-Hong

2008-01-01

This study demonstrates that a popular graphing calculator among students, TI-83 Plus, has a powerful function to draw the NPV profile and find the accurate multiple IRRs for a project with non-conventional cash flows. However, finance textbooks or related supplementary materials do not provide students instructions for this part. The detailed…

Clustering of four major lifestyle risk factors among Korean adults with metabolic syndrome.

PubMed

Ha, Shin; Choi, Hui Ran; Lee, Yo Han

2017-01-01

The purpose of this study was to investigate the clustering pattern of four major lifestyle risk factors-smoking, heavy drinking, poor diet, and physical inactivity-among people with metabolic syndrome in South Korea. There were 2,469 adults with metabolic syndrome aged 30 years or older available with the 5th Korean National Health and Nutrition Examination Survey dataset. We calculated the ratio of the observed to expected (O/E) prevalence for the 16 different combinations and the prevalence odds ratios (POR) of four lifestyle risk factors. The four lifestyle risk factors tended to cluster in specific multiple combinations. Smoking and heavy drinking was clustered (POR: 1.86 for male, 4.46 for female), heavy drinking and poor diet were clustered (POR: 1.38 for male, 1.74 for female), and smoking and physical inactivity were also clustered (POR: 1.48 for male). Those who were male, younger, low-educated and living alone were much more likely to have a higher number of lifestyle risk factors. Some helpful implications can be drawn from the knowledge on clustering pattern of lifestyle risk factors for more effective intervention program targeting metabolic syndrome.

Basic and Exceptional Calculation Abilities in a Calculating Prodigy: A Case Study.

ERIC Educational Resources Information Center

Pesenti, Mauro; Seron, Xavier; Samson, Dana; Duroux, Bruno

1999-01-01

Describes the basic and exceptional calculation abilities of a calculating prodigy whose performances were investigated in single- and multi-digit number multiplication, numerical comparison, raising of powers, and short-term memory tasks. Shows how his highly efficient long-term memory storage and retrieval processes, knowledge of calculation…

Use of erythrocyte indicators of health and condition in vertebrate ecophysiology: a review and appraisal.

PubMed

Johnstone, Christopher P; Lill, Alan; Reina, Richard D

2017-02-01

We review evidence for and against the use of erythrocyte indicators of health status and condition, parasite infection level and physiological stress in free-living vertebrates. The use of indicators that are measured directly from the blood, such as haemoglobin concentration, haematocrit and erythrocyte sedimentation rate, and parameters that are calculated from multiple measured metrics, such as mean cell volume, mean cell haemoglobin content or mean cell haemoglobin concentration is evaluated. The evidence for or against the use of any given metric is equivocal when the relevant research is considered in total, although there is sometimes strong support for using a particular metric in a particular taxon. Possibly the usefulness of these metrics is taxon, environment or condition specific. Alternatively, in an uncontrolled environment where multiple factors are influencing a metric, its response to environmental change will sometimes, but not always, be predictable. We suggest that (i) researchers should validate a metricfres utility before use, (ii) multiple metrics should be used to construct an overall erythrocyte profile for an individual or population, (iii) there is a need for researchers to compile reference ranges for free-living species, and (iv) some metrics which are useful under controlled, clinical conditions may not have the same utility or applicability for free-living vertebrates. Erythrocyte metrics provide useful information about health and condition that can be meaningfully interpreted in free-living vertebrates, but their use requires careful forethought about confounding factors. © 2015 Cambridge Philosophical Society.

Factor structure of the General Health Questionnaire-28 (GHQ-28) from infertile women attending the Yazd Research and Clinical Center for Infertility.

PubMed

Shayan, Zahra; Pourmovahed, Zahra; Najafipour, Fatemeh; Abdoli, Ali Mohammad; Mohebpour, Fatemeh; Najafipour, Sedighe

2015-12-01

Nowadays, infertility problems have become a social concern, and are associated with multiple psychological and social problems. Also, it affects the interpersonal communication between the individual, familial, and social characteristics. Since women are exposed to stressors of physical, mental, social factors, and treatment of infertility, providing a psychometric screening tool is necessary for disorders of this group. The aim of this study was to determine the factor structure of the general health questionnaire-28 to discover mental disorders in infertile women. In this study, 220 infertile women undergoing treatment of infertility were selected from the Yazd Research and Clinical Center for Infertility with convenience sampling in 2011. After completing the general health questionnaire by the project manager, validity and, reliability of the questionnaire were calculated by confirmatory factor structure and Cronbach's alpha, respectively. Four factors, including anxiety and insomnia, social dysfunction, depression, and physical symptoms were extracted from the factor structure. 50.12% of the total variance was explained by four factors. The reliability coefficient of the questionnaire was obtained 0.90. Analysis of the factor structure and reliability of General Health Questionnaire-28 showed that it is suitable as a screening instrument for assessing general health of infertile women.

Virtual screening of integrase inhibitors by large scale binding free energy calculations: the SAMPL4 challenge

PubMed Central

Gallicchio, Emilio; Deng, Nanjie; He, Peng; Wickstrom, Lauren; Perryman, Alexander L.; Santiago, Daniel N.; Forli, Stefano; Olson, Arthur J.; Levy, Ronald M.

2014-01-01

As part of the SAMPL4 blind challenge, filtered AutoDock Vina ligand docking predictions and large scale binding energy distribution analysis method binding free energy calculations have been applied to the virtual screening of a focused library of candidate binders to the LEDGF site of the HIV integrase protein. The computational protocol leveraged docking and high level atomistic models to improve enrichment. The enrichment factor of our blind predictions ranked best among all of the computational submissions, and second best overall. This work represents to our knowledge the first example of the application of an all-atom physics-based binding free energy model to large scale virtual screening. A total of 285 parallel Hamiltonian replica exchange molecular dynamics absolute protein-ligand binding free energy simulations were conducted starting from docked poses. The setup of the simulations was fully automated, calculations were distributed on multiple computing resources and were completed in a 6-weeks period. The accuracy of the docked poses and the inclusion of intramolecular strain and entropic losses in the binding free energy estimates were the major factors behind the success of the method. Lack of sufficient time and computing resources to investigate additional protonation states of the ligands was a major cause of mispredictions. The experiment demonstrated the applicability of binding free energy modeling to improve hit rates in challenging virtual screening of focused ligand libraries during lead optimization. PMID:24504704

Rapid calculation of radiative heating rates and photodissociation rates in inhomogeneous multiple scattering atmospheres

NASA Technical Reports Server (NTRS)

Toon, Owen B.; Mckay, C. P.; Ackerman, T. P.; Santhanam, K.

1989-01-01

The solution of the generalized two-stream approximation for radiative transfer in homogeneous multiple scattering atmospheres is extended to vertically inhomogeneous atmospheres in a manner which is numerically stable and computationally efficient. It is shown that solar energy deposition rates, photolysis rates, and infrared cooling rates all may be calculated with the simple modifications of a single algorithm. The accuracy of the algorithm is generally better than 10 percent, so that other uncertainties, such as in absorption coefficients, may often dominate the error in calculation of the quantities of interest to atmospheric studies.

Bidirectional associations in multiplication memory: conditions of negative and positive transfer.

PubMed

Campbell, Jamie I D; Robert, Nicole D

2008-05-01

A variety of experimental evidence indicates that the memory representation for multiplication facts (e.g., 6 x 9 = 54) incorporates bidirectional links with a forward association from factors to product and a reverse association from product to factors. Surprisingly, the authors did not find evidence in Experiment 1 of facilitative transfer-of-practice from multiplication (6 x 9 = ?) to factoring (54 = ? x ?); in fact, multiplication practice produced item-specific interference with factoring. Similarly, the authors found no evidence in Experiment 2 that repetition of specific factoring problems (54 = ? x ?) facilitated performance of corresponding multiplication problems (6 x 9 = ?). In Experiment 3, participants practiced both multiplication and factoring and presented facilitative transfer in both directions. Thus, bidirectional facilitation occurred if both operations were practiced, but interference occurred when only one operation was practiced. We propose that this seemingly paradoxical behavior occurs because it is adaptive for the bidirectional retrieval structure to retain operational flexibility in the context of practicing both operations, whereas it is adaptive to specialize the memory representation for the practiced operation (i.e., factoring or multiplication) when only one operation is practiced.

Development of a CSP plant energy yield calculation tool applying predictive models to analyze plant performance sensitivities

NASA Astrophysics Data System (ADS)

Haack, Lukas; Peniche, Ricardo; Sommer, Lutz; Kather, Alfons

2017-06-01

At early project stages, the main CSP plant design parameters such as turbine capacity, solar field size, and thermal storage capacity are varied during the techno-economic optimization to determine most suitable plant configurations. In general, a typical meteorological year with at least hourly time resolution is used to analyze each plant configuration. Different software tools are available to simulate the annual energy yield. Software tools offering a thermodynamic modeling approach of the power block and the CSP thermal cycle, such as EBSILONProfessional®, allow a flexible definition of plant topologies. In EBSILON, the thermodynamic equilibrium for each time step is calculated iteratively (quasi steady state), which requires approximately 45 minutes to process one year with hourly time resolution. For better presentation of gradients, 10 min time resolution is recommended, which increases processing time by a factor of 5. Therefore, analyzing a large number of plant sensitivities, as required during the techno-economic optimization procedure, the detailed thermodynamic simulation approach becomes impracticable. Suntrace has developed an in-house CSP-Simulation tool (CSPsim), based on EBSILON and applying predictive models, to approximate the CSP plant performance for central receiver and parabolic trough technology. CSPsim significantly increases the speed of energy yield calculations by factor ≥ 35 and has automated the simulation run of all predefined design configurations in sequential order during the optimization procedure. To develop the predictive models, multiple linear regression techniques and Design of Experiment methods are applied. The annual energy yield and derived LCOE calculated by the predictive model deviates less than ±1.5 % from the thermodynamic simulation in EBSILON and effectively identifies the optimal range of main design parameters for further, more specific analysis.

C U L8ter: YouTube distracted driving PSAs use of behavior change theory.

PubMed

Steadman, Mindy; Chao, Melanie S; Strong, Jessica T; Maxwell, Martha; West, Joshua H

2014-01-01

To examine the inclusion of health behavior theory in distracted driving PSAs on YouTube.com. Two-hundred fifty PSAs were assessed using constructs from 4 prominent health behavior theories. A total theory score was calculated for each video. Multiple regression analysis was used to identify factors associated with higher theory scores. PSAs were generally lacking in theoretical content. Video length, use of rates/statistics, driving scenario depiction, and presence of a celebrity were positively associated with theory inclusion. Collaboration between health experts and PSA creators could be fostered to produce more theory-based distracted driving videos on YouTube.com.

Exponential integrators in time-dependent density-functional calculations

NASA Astrophysics Data System (ADS)

Kidd, Daniel; Covington, Cody; Varga, Kálmán

2017-12-01

The integrating factor and exponential time differencing methods are implemented and tested for solving the time-dependent Kohn-Sham equations. Popular time propagation methods used in physics, as well as other robust numerical approaches, are compared to these exponential integrator methods in order to judge the relative merit of the computational schemes. We determine an improvement in accuracy of multiple orders of magnitude when describing dynamics driven primarily by a nonlinear potential. For cases of dynamics driven by a time-dependent external potential, the accuracy of the exponential integrator methods are less enhanced but still match or outperform the best of the conventional methods tested.

Quartz Crystal Microbalance Operation and In Situ Calibration

NASA Technical Reports Server (NTRS)

Albyn, K. C.

2004-01-01

Quartz crystal microbalances (QCMs) are commonly used to measure the rate of deposition of molecular species on a surface. The measurement is often used to select materials with a low outgassing rate for applications where the material has a line of sight to a contamination-sensitive surface. A quantitative, in situ calibration of the balance, or balances, using a pure material for which the enthalpy of sublimation is known, is described in this Technical Memorandum. Supporting calculations for surface dwell times of deposited materials and the effusion cell Clausing factor are presented along with examples of multiple QCM measurements of outgassing from a common source.

Spectral regression and correlation coefficients of some benzaldimines and salicylaldimines in different solvents

NASA Astrophysics Data System (ADS)

Hammud, Hassan H.; Ghannoum, Amer; Masoud, Mamdouh S.

2006-02-01

Sixteen Schiff bases obtained from the condensation of benzaldehyde or salicylaldehyde with various amines (aniline, 4-carboxyaniline, phenylhydrazine, 2,4-dinitrophenylhydrazine, ethylenediamine, hydrazine, o-phenylenediamine and 2,6-pyridinediamine) are studied with UV-vis spectroscopy to observe the effect of solvents, substituents and other structural factors on the spectra. The bands involving different electronic transitions are interpreted. Computerized analysis and multiple regression techniques were applied to calculate the regression and correlation coefficients based on the equation that relates peak position λmax to the solvent parameters that depend on the H-bonding ability, refractive index and dielectric constant of solvents.

Exponential approximation for daily average solar heating or photolysis. [of stratospheric ozone layer

NASA Technical Reports Server (NTRS)

Cogley, A. C.; Borucki, W. J.

1976-01-01

When incorporating formulations of instantaneous solar heating or photolytic rates as functions of altitude and sun angle into long range forecasting models, it may be desirable to replace the time integrals by daily average rates that are simple functions of latitude and season. This replacement is accomplished by approximating the integral over the solar day by a pure exponential. This gives a daily average rate as a multiplication factor times the instantaneous rate evaluated at an appropriate sun angle. The accuracy of the exponential approximation is investigated by a sample calculation using an instantaneous ozone heating formulation available in the literature.

Multiple electron processes of He and Ne by proton impact

NASA Astrophysics Data System (ADS)

Terekhin, Pavel Nikolaevich; Montenegro, Pablo; Quinto, Michele; Monti, Juan; Fojon, Omar; Rivarola, Roberto

2016-05-01

A detailed investigation of multiple electron processes (single and multiple ionization, single capture, transfer-ionization) of He and Ne is presented for proton impact at intermediate and high collision energies. Exclusive absolute cross sections for these processes have been obtained by calculation of transition probabilities in the independent electron and independent event models as a function of impact parameter in the framework of the continuum distorted wave-eikonal initial state theory. A binomial analysis is employed to calculate exclusive probabilities. The comparison with available theoretical and experimental results shows that exclusive probabilities are needed for a reliable description of the experimental data. The developed approach can be used for obtaining the input database for modeling multiple electron processes of charged particles passing through the matter.

Intermediate energy proton-deuteron elastic scattering

NASA Technical Reports Server (NTRS)

Wilson, J. W.

1973-01-01

A fully symmetrized multiple scattering series is considered for the description of proton-deuteron elastic scattering. An off-shell continuation of the experimentally known twobody amplitudes that retains the exchange symmeteries required for the calculation is presented. The one boson exchange terms of the two body amplitudes are evaluated exactly in this off-shell prescription. The first two terms of the multiple scattering series are calculated explicitly whereas multiple scattering effects are obtained as minimum variance estimates from the 146-MeV data of Postma and Wilson. The multiple scattering corrections indeed consist of low order partial waves as suggested by Sloan based on model studies with separable interactions. The Hamada-Johnston wave function is shown consistent with the data for internucleon distances greater than about 0.84 fm.

WORKING ENVIRONMENT AND JOB SATISFACTION AMONG HEALTH PROFESSIONAL WORKING AT A TERTIARY CARE HOSPITAL OF PAKISTAN.

PubMed

Aziz, Imrana; Kumar, Ramesh; Rathore, Anita; Lal, Manohr

2015-01-01

Work environment is believed to be a major factor for better performance of human resource for health in any organization. This study concentrated on multiple factors involved in job satisfaction was appraised to critique their efficient significance in calculation of the health professional liking. Factors included job matched with workers' skills/experience, incentives, supervision, administrator support; convenient work load, training, appreciation, low pay and job protection were major contributors in job satisfaction. A mix method study was done in 2014; an initial descriptive cross sectional survey was done followed by qualitative approach. Eighteen in-depth interviews with health care providers were conducted after taking written consent. Nodes, sub-nodes and final themes were generated during qualitative data analysis. Main findings and themes were, generated after making the nodes and sub-nodes from the most frequent responses. These themes were; absence of work pressure, work place safety, social support, learning opportunities, and employee influence on conditions and recognition individual or team efforts. Work environment is a major contributing factor towards job satisfaction among the health workers.

Impact of night-shift work on the prevalence of erosive esophagitis in shipyard male workers.

PubMed

Chung, Tae Heum; Lee, Jiho; Kim, Moon Chan

2016-08-01

Whether night-shift work is a risk factor for gastroesophageal reflux disease is controversial. The aim of this study was to investigate the association between night-shift work and other factors, and erosive esophagitis. A cross-sectional study with 6040 male shipyard workers was performed. Esophagogastroduodenoscopic examination and a survey about night-shift work status, lifestyle, medical history, educational status, and marital status were conducted in all workers. The odds ratios of erosive esophagitis according to night-shift work status were calculated by using the logistic regression model. The prevalence of erosive esophagitis increased in the night-shift workers [odds ratio, 95 % confidence interval: 1.41 (1.03-1.94)]. According to multiple logistic regression models, night-shift work, obesity, smoking, and alcohol consumption of ≥140 g/week were significant risk factors for erosive esophagitis. By contrast, Helicobacter pylori infection was negatively associated with erosive esophagitis. Night-shift work is suggested to be a risk factor for erosive esophagitis. Avoidance of night-shift work and lifestyle modification should be considered for prevention and management of gastroesophageal reflux disease.

Actualizing Flexible National Security Space Systems

DTIC Science & Technology

2011-01-01

single launch vehicle is a decision unique to small satellites that adds an extra dimension to the launch risk calculation. While bundling...following a launch failure. The ability to bundle multiple payloads on a single launch vehicle is a decision unique to small satellites that adds an extra ... dimension to the launch risk calculation. While bundling multiple small satellites on a single launch vehicle spreads the initial launch cost across

Determinants of health care expenditures and the contribution of associated factors: 16 cities and provinces in Korea, 2003-2010.

PubMed

Han, Kimyoung; Cho, Minho; Chun, Kihong

2013-11-01

The purpose of this study was to classify determinants of cost increases into two categories, negotiable factors and non-negotiable factors, in order to identify the determinants of health care expenditure increases and to clarify the contribution of associated factors selected based on a literature review. The data in this analysis was from the statistical yearbooks of National Health Insurance Service, the Economic Index from Statistics Korea and regional statistical yearbooks. The unit of analysis was the annual growth rate of variables of 16 cities and provinces from 2003 to 2010. First, multiple regression was used to identify the determinants of health care expenditures. We then used hierarchical multiple regression to calculate the contribution of associated factors. The changes of coefficients (R(2)) of predictors, which were entered into this analysis step by step based on the empirical evidence of the investigator could explain the contribution of predictors to increased medical cost. Health spending was mainly associated with the proportion of the elderly population, but the Medicare Economic Index (MEI) showed an inverse association. The contribution of predictors was as follows: the proportion of elderly in the population (22.4%), gross domestic product (GDP) per capita (4.5%), MEI (-12%), and other predictors (less than 1%). As Baby Boomers enter retirement, an increasing proportion of the population aged 65 and over and the GDP will continue to increase, thus accelerating the inflation of health care expenditures and precipitating a crisis in the health insurance system. Policy makers should consider providing comprehensive health services by an accountable care organization to achieve cost savings while ensuring high-quality care.

Comparison of plasma pigment epithelium-derived factor (PEDF), retinol binding protein 4 (RBP-4), chitinase-3-like protein 1 (YKL-40) and brain-derived neurotrophic factor (BDNF) for the identification of insulin resistance.

PubMed

Toloza, F J K; Pérez-Matos, M C; Ricardo-Silgado, M L; Morales-Álvarez, M C; Mantilla-Rivas, J O; Pinzón-Cortés, J A; Pérez-Mayorga, M; Arévalo-García, M L; Tolosa-González, G; Mendivil, C O

2017-09-01

To evaluate and compare the association of four potential insulin resistance (IR) biomarkers (pigment-epithelium-derived factor [PEDF], retinol-binding-protein-4 [RBP-4], chitinase-3-like protein 1 [YKL-40] and brain-derived neurotrophic factor [BDNF]) with objective measures of IR. We studied 81 subjects with different metabolic profiles. All participants underwent a 5-point OGTT with calculation of multiple IR indexes. A subgroup of 21 participants additionally underwent a hyperinsulinemic-euglycemic clamp. IR was defined as belonging to the highest quartile of incremental area under the insulin curve (iAUCins), or to the lowest quartile of the insulin sensitivity index (ISI). PEDF was associated with adiposity variables. PEDF and RBP4 increased linearly across quartiles of iAUCins (for PEDF p-trend=0.029; for RBP-4 p-trend=0.053). YKL-40 and BDNF were not associated with any adiposity or IR variable. PEDF and RBP-4 levels identified individuals with IR by the iAUCins definition: A PEDF cutoff of 11.9ng/mL had 60% sensitivity and 68% specificity, while a RBP-4 cutoff of 71.6ng/mL had 70% sensitivity and 57% specificity. In multiple regression analyses simultaneously including clinical variables and the studied biomarkers, only BMI, PEDF and RBP-4 remained significant predictors of IR. Plasma PEDF and RBP4 identified IR in subjects with no prior diagnosis of diabetes. Copyright © 2017 Elsevier Inc. All rights reserved.

Usefulness of the Trabecular Bone Score for assessing the risk of osteoporotic fracture.

PubMed

Redondo, L; Puigoriol, E; Rodríguez, J R; Peris, P; Kanterewicz, E

2018-04-01

The trabecular bone score (TBS) is an imaging technique that assesses the condition of the trabecular microarchitecture. Preliminary results suggest that TBS, along with the bone mineral density assessment, could improve the calculation of the osteoporotic fracture risk. The aim of this study was to analyse TBS values and their relationship with the clinical characteristics, bone mineral density and history of fractures of a cohort of posmenopausal women. We analysed 2,257 posmenopausal women from the FRODOS cohort, which was created to determine the risk factors for osteoporotic fracture through a clinical survey and bone densitometry with vertebral morphometry. TBS was applied to the densitometry images. TBS values ≤1230 were considered indicative of degraded microarchitecture. We performed a simple and multiple linear regression to determine the factors associated with this index. The mean TBS value in L1-L4 was 1.203±0.121. Some 55.3% of the women showed values indicating degraded microarchitecture. In the multiple linear regression analysis, the factors associated with low TBS values were age, weight, height, spinal T-score, glucocorticoid treatment, presence of type 2 diabetes and a history of fractures due to frailty. TBS showed microarchitecture degradation values in the participants of the FRODOS cohort and was associated with anthropometric factors, low bone mineral density values, the presence of fractures, a history of type 2 diabetes mellitus and the use of glucocorticoids. Copyright © 2017 Elsevier España, S.L.U. and Sociedad Española de Medicina Interna (SEMI). All rights reserved.

Nitrous oxide exchanges with the atmosphere of a constructed wetland treating wastewater. Parameters and implications for emission factors

NASA Astrophysics Data System (ADS)

Johansson, A. E.; Kasimir Klemedtsson, Å.; Klemedtsson, L.; Svensson, B. H.

2003-07-01

Static chamber measurements of N2O fluxes were taken during the 1998 and 1999 growth seasons in a Swedish constructed wetland receiving wastewater. The dominating plant species in different parts of the wetland were Lemna minor L., Typha latifolia L., Spirogyra sp. and Glyceria maxima (Hartm.) and Phalaris arundinacea (L.), respectively. There were large temporal and spatial variations in N2O fluxes, which ranged from consumption at -350 to emissions at 1791 μg N2O m-2 h-1. The largest positive flux occurred in October 1999 and the lowest in the middle of July 1999. The average N2O flux for the two years was 130 μg N2O m-2 h-1 (SD = 220). No significant differences in N2O fluxes were found between the years, even though the two growing seasons differed considerably with respect to both air temperature and precipitation. 15% of the fluxes were negative, showing a consumption of N2O. Consumption occurred on a few occasions at most measurement sites and ranged from 1-350 μg N2O m-2 h-1. 13-43% of the variation in N2O fluxes was explained by multiple linear regression analysis including principal components. Emission factors were calculated according to IPCC methods from the N2O fluxes in the constructed wetland. The calculated emission factors were always lower (0.02-0.27%) compared to the default factor provided by the IPCC (0.75%). Thus, direct application of the IPCC default factor may lead to overestimation of N2O fluxes from constructed wastewater-treating wetlands.

Quantifying cause-related mortality by weighting multiple causes of death

PubMed Central

Moreno-Betancur, Margarita; Lamarche-Vadel, Agathe; Rey, Grégoire

2016-01-01

Abstract Objective To investigate a new approach to calculating cause-related standardized mortality rates that involves assigning weights to each cause of death reported on death certificates. Methods We derived cause-related standardized mortality rates from death certificate data for France in 2010 using: (i) the classic method, which considered only the underlying cause of death; and (ii) three novel multiple-cause-of-death weighting methods, which assigned weights to multiple causes of death mentioned on death certificates: the first two multiple-cause-of-death methods assigned non-zero weights to all causes mentioned and the third assigned non-zero weights to only the underlying cause and other contributing causes that were not part of the main morbid process. As the sum of the weights for each death certificate was 1, each death had an equal influence on mortality estimates and the total number of deaths was unchanged. Mortality rates derived using the different methods were compared. Findings On average, 3.4 causes per death were listed on each certificate. The standardized mortality rate calculated using the third multiple-cause-of-death weighting method was more than 20% higher than that calculated using the classic method for five disease categories: skin diseases, mental disorders, endocrine and nutritional diseases, blood diseases and genitourinary diseases. Moreover, this method highlighted the mortality burden associated with certain diseases in specific age groups. Conclusion A multiple-cause-of-death weighting approach to calculating cause-related standardized mortality rates from death certificate data identified conditions that contributed more to mortality than indicated by the classic method. This new approach holds promise for identifying underrecognized contributors to mortality. PMID:27994280

Towards personalizing haemophilia care: using the Haemophilia Severity Score to assess 178 patients in a single institution.

PubMed

Vyas, S; Enockson, C; Hernandez, L; Valentino, L A

2014-01-01

The phenotypic variability in haemophilia is well documented; however, the biological basis beyond factor VIII and IX activities to explain the differing clinical pictures of the disease remains unclear. It has therefore been of interest to explore other modulators of the disease's variability. Furthermore, a scoring system that reflects the multiple facets of haemophilia symptoms would be useful to compare patients via a comprehensive assessment tool. To this end, Schulman et al., created a measure known as the Haemophilia Severity Score (HSS) as one way to compare phenotypic severity. The aim of this study was to document the differing symptomatology of haemophilia patients using the HSS. Clinical data for 178 haemophilia patients without inhibitors were reviewed and annual incidence of haemarthrosis, orthopaedic joint scores and annual factor usage calculated. Each parameter was then entered into the formula to create the HSS for haemophilia A and B patients with mild, moderate and severe factor deficiencies. Variability in the HSS for patients with the same baseline level of factor was observed for all three deficiency levels and both haemophilia types. In addition, we found that moderate and severe haemophilic B patients tended to have more morbidity based on the above calculations than the haemophilic A counterparts. The HSS is a comprehensive tool that allows for easy numerical comparison of haemophilic patients and elucidates the variable clinical presentation of the disease. The HSS could be used to stratify patients via other possible modulators of haemophilia and discover other aetiologies of the disease. © 2013 John Wiley & Sons Ltd.

Conditional spectrum computation incorporating multiple causal earthquakes and ground-motion prediction models

USGS Publications Warehouse

Lin, Ting; Harmsen, Stephen C.; Baker, Jack W.; Luco, Nicolas

2013-01-01

The conditional spectrum (CS) is a target spectrum (with conditional mean and conditional standard deviation) that links seismic hazard information with ground-motion selection for nonlinear dynamic analysis. Probabilistic seismic hazard analysis (PSHA) estimates the ground-motion hazard by incorporating the aleatory uncertainties in all earthquake scenarios and resulting ground motions, as well as the epistemic uncertainties in ground-motion prediction models (GMPMs) and seismic source models. Typical CS calculations to date are produced for a single earthquake scenario using a single GMPM, but more precise use requires consideration of at least multiple causal earthquakes and multiple GMPMs that are often considered in a PSHA computation. This paper presents the mathematics underlying these more precise CS calculations. Despite requiring more effort to compute than approximate calculations using a single causal earthquake and GMPM, the proposed approach produces an exact output that has a theoretical basis. To demonstrate the results of this approach and compare the exact and approximate calculations, several example calculations are performed for real sites in the western United States. The results also provide some insights regarding the circumstances under which approximate results are likely to closely match more exact results. To facilitate these more precise calculations for real applications, the exact CS calculations can now be performed for real sites in the United States using new deaggregation features in the U.S. Geological Survey hazard mapping tools. Details regarding this implementation are discussed in this paper.

A Method of Calculating Functional Independence Measure at Discharge from Functional Independence Measure Effectiveness Predicted by Multiple Regression Analysis Has a High Degree of Predictive Accuracy.

PubMed

Tokunaga, Makoto; Watanabe, Susumu; Sonoda, Shigeru

2017-09-01

Multiple linear regression analysis is often used to predict the outcome of stroke rehabilitation. However, the predictive accuracy may not be satisfactory. The objective of this study was to elucidate the predictive accuracy of a method of calculating motor Functional Independence Measure (mFIM) at discharge from mFIM effectiveness predicted by multiple regression analysis. The subjects were 505 patients with stroke who were hospitalized in a convalescent rehabilitation hospital. The formula "mFIM at discharge = mFIM effectiveness × (91 points - mFIM at admission) + mFIM at admission" was used. By including the predicted mFIM effectiveness obtained through multiple regression analysis in this formula, we obtained the predicted mFIM at discharge (A). We also used multiple regression analysis to directly predict mFIM at discharge (B). The correlation between the predicted and the measured values of mFIM at discharge was compared between A and B. The correlation coefficients were .916 for A and .878 for B. Calculating mFIM at discharge from mFIM effectiveness predicted by multiple regression analysis had a higher degree of predictive accuracy of mFIM at discharge than that directly predicted. Copyright © 2017 National Stroke Association. Published by Elsevier Inc. All rights reserved.

The MARVEL assembly for neutron multiplication.

PubMed

Chichester, David L; Kinlaw, Mathew T

2013-10-01

A new multiplying test assembly is under development at Idaho National Laboratory to support research, validation, evaluation, and learning. The item is comprised of three stacked, highly-enriched uranium (HEU) cylinders, each 11.4 cm in diameter and having a combined height of up to 11.7 cm. The combined mass of all three cylinders is 20.3 kg of HEU. Calculations for the bare configuration of the assembly indicate a multiplication level of >3.5 (k(eff)=0.72). Reflected configurations of the assembly, using either polyethylene or tungsten, are possible and have the capability of raising the assembly's multiplication level to greater than 10. This paper describes simulations performed to assess the assembly's multiplication level under different conditions and describes the resources available at INL to support the use of these materials. We also describe some preliminary calculations and test activities using the assembly to study neutron multiplication. Copyright © 2013 Elsevier Ltd. All rights reserved.

Calculation of individual isotope equilibrium constants for geochemical reactions

USGS Publications Warehouse

Thorstenson, D.C.; Parkhurst, D.L.

2004-01-01

Theory is derived from the work of Urey (Urey H. C. [1947] The thermodynamic properties of isotopic substances. J. Chem. Soc. 562-581) to calculate equilibrium constants commonly used in geochemical equilibrium and reaction-transport models for reactions of individual isotopic species. Urey showed that equilibrium constants of isotope exchange reactions for molecules that contain two or more atoms of the same element in equivalent positions are related to isotope fractionation factors by ?? = (Kex)1/n, where n is the number of atoms exchanged. This relation is extended to include species containing multiple isotopes, for example 13C16O18O and 1H2H18O. The equilibrium constants of the isotope exchange reactions can be expressed as ratios of individual isotope equilibrium constants for geochemical reactions. Knowledge of the equilibrium constant for the dominant isotopic species can then be used to calculate the individual isotope equilibrium constants. Individual isotope equilibrium constants are calculated for the reaction CO2g = CO2aq for all species that can be formed from 12C, 13C, 16O, and 18O; for the reaction between 12C18 O2aq and 1H218Ol; and among the various 1H, 2H, 16O, and 18O species of H2O. This is a subset of a larger number of equilibrium constants calculated elsewhere (Thorstenson D. C. and Parkhurst D. L. [2002] Calculation of individual isotope equilibrium constants for implementation in geochemical models. Water-Resources Investigation Report 02-4172. U.S. Geological Survey). Activity coefficients, activity-concentration conventions for the isotopic variants of H2O in the solvent 1H216Ol, and salt effects on isotope fractionation have been included in the derivations. The effects of nonideality are small because of the chemical similarity of different isotopic species of the same molecule or ion. The temperature dependence of the individual isotope equilibrium constants can be calculated from the temperature dependence of the fractionation factors. The derivations can be extended to calculation of individual isotope equilibrium constants for ion pairs and equilibrium constants for isotopic species of other chemical elements. The individual isotope approach calculates the same phase isotopic compositions as existing methods, but also provides concentrations of individual species, which are needed in calculations of mass-dependent effects in transport processes. The equilibrium constants derived in this paper are used to calculate the example of gas-water equilibrium for CO2 in an acidic aqueous solution. ?? 2004 Elsevier Ltd.

Exploring the Components of the Palmer Drought Indices Using the Apalachicola-Chattahoochee-Flint (ACF) River Basin as a Case Study

NASA Astrophysics Data System (ADS)

Perrone, D.; Duncan, L. L.; Jacobi, J. H.; Hornberger, G.

2012-12-01

Water resources are vital to sustaining ecosystem services, energy and food supplies, and industrial processes. Competition for water resources is likely to intensify as the population increases, economy grows, and land develops. Drought events intensify water scarcity, and recent events in many countries, including the United States (US), Great Britain, and Sri Lanka, highlight how important it is to provide meaningful context to water planners and managers. Palmer's drought indices - Z Index, Palmer Drought Severity Index (PDSI), and Palmer Hydrological Drought Index (PHDI) - are widely used and accepted by scientists and policy makers in the US to understand drought and manage water resources. Drought index values at the climate division scale are available, but a transparent calculation tool at multiple spatial and temporal scales is not readily available. Moreover, a close look at the development of the indices reveals a number of subjective calculation methods and regionally biased factors. For researchers studying areas with overlapping climate divisions, performing international research, or working with limited, site-specific data, the ability to control and modify calculations is desired. This research presents a transparent tool for calculating Palmer's drought indices. We use the Apalachicola-Chattahoochee-Flint (ACF) River Basin, located in the southeastern US, as our case study to explore and evaluate the sensitivity of Palmer's indices to temperature and precipitation anomalies, calibration periods, and other index components. The ACF has suffered two major droughts (2007 and 2012) in the past five years and supports multiple demand-side sectors - agriculture in Georgia, public and recreational supply for the Atlanta metropolitan area, hydroelectric power in Alabama, tri-state navigation, and ecosystem services. We show how the PDSI varies in response to changes in precipitation, calibration period, and a number of other variables. The aim of the work is to make this easily used tool available to help professionals who work toward facilitating water management and reducing water conflicts in the future.

Sparse matrix multiplications for linear scaling electronic structure calculations in an atom-centered basis set using multiatom blocks.

PubMed

Saravanan, Chandra; Shao, Yihan; Baer, Roi; Ross, Philip N; Head-Gordon, Martin

2003-04-15

A sparse matrix multiplication scheme with multiatom blocks is reported, a tool that can be very useful for developing linear-scaling methods with atom-centered basis functions. Compared to conventional element-by-element sparse matrix multiplication schemes, efficiency is gained by the use of the highly optimized basic linear algebra subroutines (BLAS). However, some sparsity is lost in the multiatom blocking scheme because these matrix blocks will in general contain negligible elements. As a result, an optimal block size that minimizes the CPU time by balancing these two effects is recovered. In calculations on linear alkanes, polyglycines, estane polymers, and water clusters the optimal block size is found to be between 40 and 100 basis functions, where about 55-75% of the machine peak performance was achieved on an IBM RS6000 workstation. In these calculations, the blocked sparse matrix multiplications can be 10 times faster than a standard element-by-element sparse matrix package. Copyright 2003 Wiley Periodicals, Inc. J Comput Chem 24: 618-622, 2003

Temperature Histories of Structural Steel Laser and Hybrid Laser-GMA Welds Calculated Using Multiple Constraints

DTIC Science & Technology

2015-12-10

Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/6390--15-9665 Temperature Histories of Structural Steel Laser and Hybrid Laser-GMA Welds ...NUMBER OF PAGES 17. LIMITATION OF ABSTRACT Temperature Histories of Structural Steel Laser and Hybrid Laser-GMA Welds Calculated Using Multiple...structures. These analyses provide parametric representations of weld temperature histories that can be adopted as input data to various types of

A model for multiple-drop-impact erosion of brittle solids

NASA Technical Reports Server (NTRS)

Engel, O. G.

1971-01-01

A statistical model for the multiple-drop-impact erosion of brittle solids was developed. An equation for calculating the rate of erosion is given. The development is not complete since two quantities that are needed to calculate the rate of erosion with use of the equation must be assessed from experimental data. A partial test of the equation shows that it gives results that are in good agreement with experimental observation.

Temperature Histories of Structural Steel Laser and Hybrid Laser-GMA Welds Calculated Using Multiple Constraints

DTIC Science & Technology

2015-12-10

Naval Research Laboratory Washington, DC 20375-5320 NRL/MR/6390--15-9665 Temperature Histories of Structural Steel Laser and Hybrid Laser-GMA Welds ...NUMBER OF PAGES 17. LIMITATION OF ABSTRACT Temperature Histories of Structural Steel Laser and Hybrid Laser-GMA Welds Calculated Using Multiple...202) 767-2601 Inverse thermal analyses of structural steel deep-penetration welds are presented. These analyses employ a methodology that is in terms of

Thermophysics Characterization of Multiply Ionized Air Plasma Absorption of Laser Radiation

NASA Technical Reports Server (NTRS)

Wang, Ten-See; Rhodes, Robert; Turner, Jim (Technical Monitor)

2002-01-01

The impact of multiple ionization of air plasma on the inverse Bremsstrahlung absorption of laser radiation is investigated for air breathing laser propulsion. Thermochemical properties of multiply ionized air plasma species are computed for temperatures up to 200,000 deg K, using hydrogenic approximation of the electronic partition function; And those for neutral air molecules are also updated for temperatures up to 50,000 deg K, using available literature data. Three formulas for absorption are calculated and a general formula is recommended for multiple ionization absorption calculation. The plasma composition required for absorption calculation is obtained by increasing the degree of ionization sequentially, up to quadruple ionization, with a series of thermal equilibrium computations. The calculated second ionization absorption coefficient agrees reasonably well with that of available data. The importance of multiple ionization modeling is demonstrated with the finding that area under the quadruple ionization curve of absorption is found to be twice that of single ionization. The effort of this work is beneficial to the computational plasma aerodynamics modeling of laser lightcraft performance.

New approach to CT pixel-based photon dose calculations in heterogeneous media

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wong, J.W.; Henkelman, R.M.

The effects of small cavities on dose in water and the dose in a homogeneous nonunit density medium illustrate that inhomogeneities do not act independently in photon dose perturbation, and serve as two constraints which should be satisfied by approximate methods of computed tomography (CT) pixel-based dose calculations. Current methods at best satisfy only one of the two constraints and show inadequacies in some intermediate geometries. We have developed an approximate method that satisfies both these constraints and treats much of the synergistic effect of multiple inhomogeneities correctly. The method calculates primary and first-scatter doses by first-order ray tracing withmore » the first-scatter contribution augmented by a component of second scatter that behaves like first scatter. Multiple-scatter dose perturbation values extracted from small cavity experiments are used in a function which approximates the small residual multiple-scatter dose. For a wide range of geometries tested, our method agrees very well with measurements. The average deviation is less than 2% with a maximum of 3%. In comparison, calculations based on existing methods can have errors larger than 10%.« less

Risk factors for lesions of the knee menisci among workers in South Korea's national parks.

PubMed

Shin, Donghee; Youn, Kanwoo; Lee, Eunja; Lee, Myeongjun; Chung, Hweemin; Kim, Deokweon

2016-01-01

This study was designed to investigate the prevalence of the menisci lesions in national park workers and work factors affecting this prevalence. The study subjects were 698 workers who worked in 20 Korean national parks in 2014. An orthopedist visited each national park and performed physical examinations. Knee MRI was performed if the McMurray test or Apley test was positive and there was a complaint of pain in knee area. An orthopedist and a radiologist respectively read these images of the menisci using a grading system based on the MRI signals. To calculate the cumulative intensity of trekking of the workers, the mean trail distance, the difficulty of the trail, the tenure at each national parks, and the number of treks per month for each worker from the start of work until the present were investigated. Chi-square tests was performed to see if there were differences in the menisci lesions grade according to the variables. The variables used in the Chi-square test were evaluated using simple logistic regression analysis to get crude odds ratios, and adjusted odds ratios and 95 % confidence intervals were calculated using multivariate logistic regression analysis after establishing three different models according to the adjusted variables. According to the MRI signal grades of menisci, 29 % were grade 0, 11.3 % were grade 1, 46.0 % were grade 2, and 13.7 % were grade 3. The differences in the MRI signal grades of menisci according to age and the intensity of trekking as calculated by the three different methods were statistically significant. Multiple logistic regression analysis was performed for three models. In model 1, there was no statistically significant factor affecting the menisci lesions. In model 2, among the factors affecting the menisci lesions, the OR of a high cumulative intensity of trekking was 4.08 (95 % CI 1.00-16.61), and in model 3, the OR of a high cumulative intensity of trekking was 5.84 (95 % CI 1.09-31.26). The factor that most affected the menisci lesions among the workers in Korean national park was a high cumulative intensity of trekking.

A Spanish-language patient safety questionnaire to measure medical and nursing students' attitudes and knowledge.

PubMed

Mira, José J; Navarro, Isabel M; Guilabert, Mercedes; Poblete, Rodrigo; Franco, Astolfo L; Jiménez, Pilar; Aquino, Margarita; Fernández-Trujillo, Francisco J; Lorenzo, Susana; Vitaller, Julián; de Valle, Yohana Díaz; Aibar, Carlos; Aranaz, Jesús M; De Pedro, José A

2015-08-01

To design and validate a questionnaire for assessing attitudes and knowledge about patient safety using a sample of medical and nursing students undergoing clinical training in Spain and four countries in Latin America. In this cross-sectional study, a literature review was carried out and total of 786 medical and nursing students were surveyed at eight universities from five countries (Chile, Colombia, El Salvador, Guatemala, and Spain) to develop and refine a Spanish-language questionnaire on knowledge and attitudes about patient safety. The scope of the questionnaire was based on five dimensions (factors) presented in studies related to patient safety culture found in PubMed and Scopus. Based on the five factors, 25 reactive items were developed. Composite reliability indexes and Cronbach's alpha statistics were estimated for each factor, and confirmatory factor analysis was conducted to assess validity. After a pilot test, the questionnaire was refined using confirmatory models, maximum-likelihood estimation, and the variance-covariance matrix (as input). Multiple linear regression models were used to confirm external validity, considering variables related to patient safety culture as dependent variables and the five factors as independent variables. The final instrument was a structured five-point Likert self-administered survey (the "Latino Student Patient Safety Questionnaire") consisting of 21 items grouped into five factors. Compound reliability indexes (Cronbach's alpha statistic) calculated for the five factors were about 0.7 or higher. The results of the multiple linear regression analyses indicated good model fit (goodness-of-fit index: 0.9). Item-total correlations were higher than 0.3 in all cases. The convergent-discriminant validity was adequate. The questionnaire designed and validated in this study assesses nursing and medical students' attitudes and knowledge about patient safety. This instrument could be used to indirectly evaluate whether or not students in health disciplines are acquiring and thus likely to put into practice the professional skills currently considered most appropriate for patient safety.

Using agent-based modeling to study multiple risk factors and multiple health outcomes at multiple levels.

PubMed

Yang, Yong

2017-11-01

Most health studies focus on one health outcome and examine the influence of one or multiple risk factors. However, in reality, various pathways, interactions, and associations exist not only between risk factors and health outcomes but also among the risk factors and among health outcomes. The advance of system science methods, Big Data, and accumulated knowledge allows us to examine how multiple risk factors influence multiple health outcomes at multiple levels (termed a 3M study). Using the study of neighborhood environment and health as an example, I elaborate on the significance of 3M studies. 3M studies may lead to a significantly deeper understanding of the dynamic interactions among risk factors and outcomes and could help us design better interventions that may be of particular relevance for upstream interventions. Agent-based modeling (ABM) is a promising method in the 3M study, although its potentials are far from being fully explored. Future challenges include the gap of epidemiologic knowledge and evidence, lack of empirical data sources, and the technical challenges of ABM. © 2017 New York Academy of Sciences.

Is Hypovitaminosis D One of the Environmental Risk Factors for Multiple Sclerosis?

ERIC Educational Resources Information Center

Pierrot-Deseilligny, Charles; Souberbielle, Jean-Claude

2010-01-01

The role of hypovitaminosis D as a possible risk factor for multiple sclerosis is reviewed. First, it is emphasized that hypovitaminosis D could be only one of the risk factors for multiple sclerosis and that numerous other environmental and genetic risk factors appear to interact and combine to trigger the disease. Secondly, the classical…

SU-F-T-67: Correction Factors for Monitor Unit Verification of Clinical Electron Beams

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haywood, J

Purpose: Monitor units calculated by electron Monte Carlo treatment planning systems are often higher than TG-71 hand calculations for a majority of patients. Here I’ve calculated tables of geometry and heterogeneity correction factors for correcting electron hand calculations. Method: A flat water phantom with spherical volumes having radii ranging from 3 to 15 cm was created. The spheres were centered with respect to the flat water phantom, and all shapes shared a surface at 100 cm SSD. D{sub max} dose at 100 cm SSD was calculated for each cone and energy on the flat phantom and for the spherical volumesmore » in the absence of the flat phantom. The ratio of dose in the sphere to dose in the flat phantom defined the geometrical correction factor. The heterogeneity factors were then calculated from the unrestricted collisional stopping power for tissues encountered in electron beam treatments. These factors were then used in patient second check calculations. Patient curvature was estimated by the largest sphere that aligns to the patient contour, and appropriate tissue density was read from the physical properties provided by the CT. The resulting MU were compared to those calculated by the treatment planning system and TG-71 hand calculations. Results: The geometry and heterogeneity correction factors range from ∼(0.8–1.0) and ∼(0.9–1.01) respectively for the energies and cones presented. Percent differences for TG-71 hand calculations drop from ∼(3–14)% to ∼(0–2)%. Conclusion: Monitor units calculated with the correction factors typically decrease the percent difference to under actionable levels, < 5%. While these correction factors work for a majority of patients, there are some patient anatomies that do not fit the assumptions made. Using these factors in hand calculations is a first step in bringing the verification monitor units into agreement with the treatment planning system MU.« less

Massive Photons: An Infrared Regularization Scheme for Lattice QCD+QED.

PubMed

Endres, Michael G; Shindler, Andrea; Tiburzi, Brian C; Walker-Loud, André

2016-08-12

Standard methods for including electromagnetic interactions in lattice quantum chromodynamics calculations result in power-law finite-volume corrections to physical quantities. Removing these by extrapolation requires costly computations at multiple volumes. We introduce a photon mass to alternatively regulate the infrared, and rely on effective field theory to remove its unphysical effects. Electromagnetic modifications to the hadron spectrum are reliably estimated with a precision and cost comparable to conventional approaches that utilize multiple larger volumes. A significant overall cost advantage emerges when accounting for ensemble generation. The proposed method may benefit lattice calculations involving multiple charged hadrons, as well as quantum many-body computations with long-range Coulomb interactions.

Exploratory tests of two strut fuel injectors for supersonic combustion

NASA Technical Reports Server (NTRS)

Anderson, G. Y.; Gooderum, P. B.

1974-01-01

Results of supersonic mixing and combustion tests performed with two simple strut injector configurations, one with parallel injectors and one with perpendicular injectors, are presented and analyzed. Good agreement is obtained between static pressure measured on the duct wall downstream of the strut injectors and distributions obtained from one-dimensional calculations. Measured duct heat load agrees with results of the one-dimensional calculations for moderate amounts of reaction, but is underestimated when large separated regions occur near the injection location. For the parallel injection strut, good agreement is obtained between the shape of the injected fuel distribution inferred from gas sample measurements at the duct exit and the distribution calculated with a multiple-jet mixing theory. The overall fraction of injected fuel reacted in the multiple-jet calculation closely matches the amount of fuel reaction necessary to match static pressure with the one-dimensional calculation. Gas sample measurements with the perpendicular injection strut also give results consistent with the amount of fuel reaction in the one-dimensional calculation.

An Updated Meta-Analysis of Risk of Multiple Sclerosis following Infectious Mononucleosis

PubMed Central

Handel, Adam E.; Williamson, Alexander J.; Disanto, Giulio; Handunnetthi, Lahiru; Giovannoni, Gavin; Ramagopalan, Sreeram V.

2010-01-01

Background Multiple sclerosis (MS) appears to develop in genetically susceptible individuals as a result of environmental exposures. Epstein-Barr virus (EBV) infection is an almost universal finding among individuals with MS. Symptomatic EBV infection as manifested by infectious mononucleosis (IM) has been shown in a previous meta-analysis to be associated with the risk of MS, however a number of much larger studies have since been published. Methods/Principal Findings We performed a Medline search to identify articles published since the original meta-analysis investigating MS risk following IM. A total of 18 articles were included in this study, including 19390 MS patients and 16007 controls. We calculated the relative risk of MS following IM using a generic inverse variance with random effects model. This showed that the risk of MS was strongly associated with IM (relative risk (RR) 2.17; 95% confidence interval 1.97–2.39; p<10−54). Discussion Our results establish firmly that a history of infectious mononucleosis significantly increases the risk of multiple sclerosis. Future work should focus on the mechanism of this association and interaction with other risk factors. PMID:20824132

An empirical model for polarized and cross-polarized scattering from a vegetation layer

NASA Technical Reports Server (NTRS)

Liu, H. L.; Fung, A. K.

1988-01-01

An empirical model for scattering from a vegetation layer above an irregular ground surface is developed in terms of the first-order solution for like-polarized scattering and the second-order solution for cross-polarized scattering. The effects of multiple scattering within the layer and at the surface-volume boundary are compensated by using a correction factor based on the matrix doubling method. The major feature of this model is that all parameters in the model are physical parameters of the vegetation medium. There are no regression parameters. Comparisons of this empirical model with theoretical matrix-doubling method and radar measurements indicate good agreements in polarization, angular trends, and k sub a up to 4, where k is the wave number and a is the disk radius. The computational time is shortened by a factor of 8, relative to the theoretical model calculation.

Weighted minimum-norm source estimation of magnetoencephalography utilizing the temporal information of the measured data

NASA Astrophysics Data System (ADS)

Iwaki, Sunao; Ueno, Shoogo

1998-06-01

The weighted minimum-norm estimation (wMNE) is a popular method to obtain the source distribution in the human brain from magneto- and electro- encephalograpic measurements when detailed information about the generator profile is not available. We propose a method to reconstruct current distributions in the human brain based on the wMNE technique with the weighting factors defined by a simplified multiple signal classification (MUSIC) prescanning. In this method, in addition to the conventional depth normalization technique, weighting factors of the wMNE were determined by the cost values previously calculated by a simplified MUSIC scanning which contains the temporal information of the measured data. We performed computer simulations of this method and compared it with the conventional wMNE method. The results show that the proposed method is effective for the reconstruction of the current distributions from noisy data.

A general mixture theory. I. Mixtures of spherical molecules

NASA Astrophysics Data System (ADS)

Hamad, Esam Z.

1996-08-01

We present a new general theory for obtaining mixture properties from the pure species equations of state. The theory addresses the composition and the unlike interactions dependence of mixture equation of state. The density expansion of the mixture equation gives the exact composition dependence of all virial coefficients. The theory introduces multiple-index parameters that can be calculated from binary unlike interaction parameters. In this first part of the work, details are presented for the first and second levels of approximations for spherical molecules. The second order model is simple and very accurate. It predicts the compressibility factor of additive hard spheres within simulation uncertainty (equimolar with size ratio of three). For nonadditive hard spheres, comparison with compressibility factor simulation data over a wide range of density, composition, and nonadditivity parameter, gave an average error of 2%. For mixtures of Lennard-Jones molecules, the model predictions are better than the Weeks-Chandler-Anderson perturbation theory.

Pubertal Stage, Body Mass Index, and Cardiometabolic Risk in Children and Adolescents in Bogotá, Colombia: The Cross-Sectional Fuprecol Study

PubMed Central

Ramírez-Vélez, Robinson; García-Hermoso, Antonio; Agostinis-Sobrinho, Cesar; Mota, Jorge; Santos, Rute; Correa-Bautista, Jorge Enrique; Peña-Guzmán, Carlos Andrés; Domínguez-Sánchez, María Andrea; Schmidt-RioValle, Jacqueline; González-Jiménez, Emilio

2017-01-01

This study explored the association between pubertal stage and anthropometric and cardiometabolic risk factors in youth. A cross-sectional study was conducted in 2877 Colombian children and adolescents (9–17.9 years of age). Weight, height, and waist circumference were measured and body mass index (BMI) was calculated. A biochemical study was performed to determine the cardiometabolic risk index (CMRI). Blood pressure was evaluated and pubertal stage was assessed with the Tanner criteria. Hierarchical multiple regression analyses were performed. The most significant variable (p < 0.05) in the prognosis of cardiometabolic risk was found to be the BMI in both boys and girls. In the case of girls, the pubertal stage was also a CMRI predictive factor. In conclusion, BMI was an important indicator of cardiovascular risk in both sexes. Pubertal stage was associated with cardiovascular risk only in the girls. PMID:28640231

Linear and nonlinear models for predicting fish bioconcentration factors for pesticides.

PubMed

Yuan, Jintao; Xie, Chun; Zhang, Ting; Sun, Jinfang; Yuan, Xuejie; Yu, Shuling; Zhang, Yingbiao; Cao, Yunyuan; Yu, Xingchen; Yang, Xuan; Yao, Wu

2016-08-01

This work is devoted to the applications of the multiple linear regression (MLR), multilayer perceptron neural network (MLP NN) and projection pursuit regression (PPR) to quantitative structure-property relationship analysis of bioconcentration factors (BCFs) of pesticides tested on Bluegill (Lepomis macrochirus). Molecular descriptors of a total of 107 pesticides were calculated with the DRAGON Software and selected by inverse enhanced replacement method. Based on the selected DRAGON descriptors, a linear model was built by MLR, nonlinear models were developed using MLP NN and PPR. The robustness of the obtained models was assessed by cross-validation and external validation using test set. Outliers were also examined and deleted to improve predictive power. Comparative results revealed that PPR achieved the most accurate predictions. This study offers useful models and information for BCF prediction, risk assessment, and pesticide formulation. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pubertal Stage, Body Mass Index, and Cardiometabolic Risk in Children and Adolescents in Bogotá, Colombia: The Cross-Sectional Fuprecol Study.

PubMed

Ramírez-Vélez, Robinson; García-Hermoso, Antonio; Agostinis-Sobrinho, Cesar; Mota, Jorge; Santos, Rute; Correa-Bautista, Jorge Enrique; Peña-Guzmán, Carlos Andrés; Domínguez-Sánchez, María Andrea; Schmidt-RioValle, Jacqueline; González-Jiménez, Emilio

2017-06-22

This study explored the association between pubertal stage and anthropometric and cardiometabolic risk factors in youth. A cross-sectional study was conducted in 2877 Colombian children and adolescents (9-17.9 years of age). Weight, height, and waist circumference were measured and body mass index (BMI) was calculated. A biochemical study was performed to determine the cardiometabolic risk index (CMRI). Blood pressure was evaluated and pubertal stage was assessed with the Tanner criteria. Hierarchical multiple regression analyses were performed. The most significant variable ( p < 0.05) in the prognosis of cardiometabolic risk was found to be the BMI in both boys and girls. In the case of girls, the pubertal stage was also a CMRI predictive factor. In conclusion, BMI was an important indicator of cardiovascular risk in both sexes. Pubertal stage was associated with cardiovascular risk only in the girls.

Integrated optics to improve resolution on multiple configuration

NASA Astrophysics Data System (ADS)

Liu, Hua; Ding, Quanxin; Guo, Chunjie; Zhou, Liwei

2015-04-01

Inspired to in order to reveal the structure to improve imaging resolution, further technical requirement is proposed in some areas of the function and influence on the development of multiple configuration. To breakthrough diffraction limit, smart structures are recommended as the most efficient and economical method, while by used to improve the system performance, especially on signal to noise ratio and resolution. Integrated optics were considered in the selection, with which typical multiple configuration, by use the method of simulation experiment. Methodology can change traditional design concept and to develop the application space. Our calculations using multiple matrix transfer method, also the correlative algorithm and full calculations, show the expected beam shaping through system and, in particular, the experimental results will support our argument, which will be reported in the presentation.

Malignant testicular tumour incidence and mortality trends

PubMed Central

Wojtyła-Buciora, Paulina; Więckowska, Barbara; Krzywinska-Wiewiorowska, Małgorzata; Gromadecka-Sutkiewicz, Małgorzata

2016-01-01

Aim of the study In Poland testicular tumours are the most frequent cancer among men aged 20–44 years. Testicular tumour incidence since the 1980s and 1990s has been diversified geographically, with an increased risk of mortality in Wielkopolska Province, which was highlighted at the turn of the 1980s and 1990s. The aim of the study was the comparative analysis of the tendencies in incidence and death rates due to malignant testicular tumours observed among men in Poland and in Wielkopolska Province. Material and methods Data from the National Cancer Registry were used for calculations. The incidence/mortality rates among men due to malignant testicular cancer as well as the tendencies in incidence/death ratio observed in Poland and Wielkopolska were established based on regression equation. The analysis was deepened by adopting the multiple linear regression model. A p-value < 0.05 was arbitrarily adopted as the criterion of statistical significance, and for multiple comparisons it was modified according to the Bonferroni adjustment to a value of p < 0.0028. Calculations were performed with the use of PQStat v1.4.8 package. Results The incidence of malignant testicular neoplasms observed among men in Poland and in Wielkopolska Province indicated a significant rising tendency. The multiple linear regression model confirmed that the year variable is a strong incidence forecast factor only within the territory of Poland. A corresponding analysis of mortality rates among men in Poland and in Wielkopolska Province did not show any statistically significant correlations. Conclusions Late diagnosis of Polish patients calls for undertaking appropriate educational activities that would facilitate earlier reporting of the patients, thus increasing their chances for recovery. Introducing preventive examinations in the regions of increased risk of testicular tumour may allow earlier diagnosis. PMID:27095941

Modeling and analysis of the TF30-P-3 compressor system with inlet pressure distortion

NASA Technical Reports Server (NTRS)

Mazzawy, R. S.; Banks, G. A.

1976-01-01

Circumferential inlet distortion testing of a TF30-P-3 afterburning turbofan engine was conducted at NASA-Lewis Research Center. Pratt and Whitney Aircraft analyzed the data using its multiple segment parallel compressor model and classical compressor theory. Distortion attenuation analysis resulted in a detailed flow field calculation with good agreement between multiple segment model predictions and the test data. Sensitivity of the engine stall line to circumferential inlet distortion was calculated on the basis of parallel compressor theory to be more severe than indicated by the data. However, the calculated stall site location was in agreement with high response instrumentation measurements.

Psychometric evaluation of the Finnish version of the impact on participation and autonomy questionnaire in persons with multiple sclerosis.

PubMed

Karhula, Maarit E; Salminen, Anna-Liisa; Hämäläinen, Päivi I; Ruutiainen, Juhani; Era, Pertti; Tolvanen, Asko

2017-11-01

The objective of this study was to evaluate the psychometric properties of the impact on participation and autonomy (IPA) questionnaire. The Finnish version of IPA (IPAFin) was translated into Finnish using the protocol for linguistic validation for patient-reported outcomes instruments. A total of 194 persons with multiple sclerosis (MS) (mean age 50 years SD 9, 72% female) with moderate to severe disability participated in this study. A confirmatory factor analysis (CFA) was used to confirm the four factor structure of the IPAFin. The work and educational opportunities domain was excluded from analysis, because it was only applicable to 51 persons. Internal consistency was investigated by calculating Cronbach's alpha. CFA confirmed the construct validity of the IPA (standardized root mean square residual (SRMR) = 0.06, comparative fit index (CFI) = 0.93, Tucker-Lewis index =0.93, root mean square error of approximation (RMSEA) = 0.06), indicating a good fit to the model. There was no difference in the models for females and males. Cronbach's alpha for the domains ranged between 0.80 and 0.91, indicating good homogeneity. The construct validity and reliability of the IPAFin is acceptable. IPAFin is a suitable measure of participation in persons with MS.

Autonomous motivation and quality of life as predictors of physical activity in patients with schizophrenia.

PubMed

Costa, Raquel; Bastos, Tânia; Probst, Michel; Seabra, André; Vilhena, Estela; Corredeira, Rui

2018-02-08

Being physically active is a complex behaviour in patients with schizophrenia. Several factors were identified as barriers to achieving active behaviours in this population. Therefore, the purpose of this study was to investigate among a number of barriers what predicts the most on physical activity (PA) in patients with schizophrenia. A total of 114 patients (28♀) with schizophrenia were included. Body mass index (BMI) was calculated. Autonomous and controlled motivation (Behavioural Regulation in Exercise Questionnaire - 3), self-esteem (Rosenberg Self-esteem scale), quality of life (World Health Organization Quality of Life Scale - Brief version) and functional exercise capacity (6-minute walk test - 6MWT) were evaluated. Multiple Regression Analysis was applied to assess the effect of these variables on Total PA per week (International Physical Activity Questionnaire - short version). Autonomous motivation and domains of quality of life were positively correlated with Total PA per week. Stepwise multiple regression analyses showed that of all the candidate factors to predict PA, autonomous motivation and global domain of quality of life were found as significant predictors. Our findings help to understand the importance of autonomous motivation and quality of life for PA in patients with schizophrenia. Knowledge about these predictors may provide guidance to improve PA behaviour in this population.

Accuracy of Home-Based Ultrasonographic Diagnosis of Obstetric Risk Factors by Primary-Level Health Workers in Rural Nepal

PubMed Central

Kozuki, Naoko; Mullany, Luke C.; Khatry, Subarna K.; Ghimire, Ram K.; Paudel, Sharma; Blakemore, Karin; Bird, Christine; Tielsch, James M.; LeClerq, Steven C.; Katz, Joanne

2016-01-01

Objective To assess the feasibility of task shifting by estimating the accuracy at which primary-level health care workers can perform community-based third trimester ultrasound diagnosis for selected obstetric risk factors in rural Nepal. Methods Three auxiliary nurse midwives received two one-week ultrasound trainings at Tribhuvan University Teaching Hospital in Kathmandu. In our study site in rural Nepal, women who were ≥32 weeks in gestational age were enrolled and received ultrasound examinations from the auxiliary nurse midwives during home visits. Each auxiliary nurse midwife screened for non-cephalic presentation, multiple gestation, and placenta previa. All de-identified images were stored and uploaded onto an online server, where certified sonologists and sonographers reviewed the images and made their own diagnoses for the three conditions. Accuracy of auxiliary nurse midwife diagnoses was then calculated. Results We enrolled 804 women in the study. Each auxiliary nurse midwife’s kappa statistic for diagnosis of non-cephalic presentation was above 0.90 compared with the sonogram reviewers. Sensitivity, specificity, positive and negative predictive values were between 90–100% for all auxiliary nurse midwives For multiple gestation, the auxiliary nurse midwives were in perfect agreement with both the sonogram reviewers and maternal postpartum self-report. Two placenta previa cases were detected, and the sonogram reviewers agreed with both. Conclusion With limited training, primary-level health care workers in rural Nepal can accurately diagnose selected third trimester obstetric risk factors using ultrasonography. PMID:27500343

Hypervelocity impacts on asteroids and momentum transfer I. Numerical simulations using porous targets

NASA Astrophysics Data System (ADS)

Jutzi, Martin; Michel, Patrick

2014-02-01

In this paper, we investigate numerically the momentum transferred by impacts of small (artificial) projectiles on asteroids. The study of the momentum transfer efficiency as a function of impact conditions and of the internal structure of an asteroid is crucial for performance assessment of the kinetic impactor concept of deflecting an asteroid from its trajectory. The momentum transfer is characterized by the so-called momentum multiplication factor β, which has been introduced to define the momentum imparted to an asteroid in terms of the momentum of the impactor. Here we present results of code calculations of the β factor for porous targets, in which porosity takes the form of microporosity and/or macroporosity. The results of our study using a large range of impact conditions indicate that the momentum multiplication factor β is small for porous targets even for very high impact velocities (β<2 for vimp⩽15 km/s), which is consistent with published scaling laws and results of laboratory experiments (Holsapple, K.A., Housen, K.R. [2012]. Icarus 221, 875-887; Holsapple, K.A., Housen, K.R. [2013]. Proceedings of the IAA Planetary Defense Conference 2013, Flagstaff, USA). It is found that both porosity and strength can have a large effect on the amount of transferred momentum and on the scaling of β with impact velocity. On the other hand, the macroporous inhomogeneities considered here do not have a significant effect on β.

Preliminary neutronics design of china lead-alloy cooled demonstration reactor (CLEAR-III) for nuclear waste transmutation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Z.; Southwest Science and Technology Univ., No.350 Shushanhu Road, Shushan District, Hefei, Anhui, 230031; Chen, Y.

2012-07-01

China Lead-Alloy cooled Demonstration Reactor (CLEAR-III), which is the concept of lead-bismuth cooled accelerator driven sub-critical reactor for nuclear waste transmutation, was proposed and designed by FDS team in China. In this study, preliminary neutronics design studies have primarily focused on three important performance parameters including Transmutation Support Ratio (TSR), effective multiplication factor and blanket thermal power. The constraint parameters, such as power peaking factor and initial TRU loading, were also considered. In the specific design, uranium-free metallic dispersion fuel of (TRU-Zr)-Zr was used as one of the CLEAR-III fuel types and the ratio between MA and Pu was adjustedmore » to maximize transmutation ratio. In addition, three different fuel zones differing in the TRU fraction of the fuel were respectively employed for this subcritical reactor, and the zone sizes and TRU fractions were determined such that the linear powers of these zones were close to each other. The neutronics calculations and analyses were performed by using Multi-Functional 4D Neutronics Simulation System named VisualBUS and nuclear data library HENDL (Hybrid Evaluated Nuclear Data Library). In the preliminary design, the maximum TSRLLMA was {approx}11 and the blanket thermal power was {approx}1000 MW when the effective multiplication factor was 0.98. The results showed that good performance of transmutation could be achieved based on the subcritical reactor loaded with uranium-free fuel. (authors)« less

Accounting for time-dependent effects in biofuel life cycle greenhouse gas emissions calculations.

PubMed

Kendall, Alissa; Chang, Brenda; Sharpe, Benjamin

2009-09-15

This paper proposes a time correction factor (TCF) to properly account for the timing of land use change-derived greenhouse gas emissions in the biofuels life cycle. Land use change emissions occur at the outset of biofuel feedstock production, and are typically amortized over an assumed time horizon to assign the burdens of land use change to multiple generations of feedstock crops. Greenhouse gas intensity calculations amortize emissions by dividing them equally over a time horizon, overlooking the fact that the effect of a greenhouse gas increases with the time it remains in the atmosphere. The TCF is calculated based on the relative climate change effect of an emission occurring at the outset of biofuel feedstock cultivation versus one amortized over a time horizon. For time horizons between 10 and 50 years, the TCF varies between 1.7 and 1.8 for carbon dioxide emissions, indicating that the actual climate change effect of an emission is 70-80% higher than the effect of its amortized values. The TCF has broad relevance for correcting the treatment of emissions timing in other life cycle assessment applications, such as emissions from capital investments for production systems or manufacturing emissions for renewable energy technologies.

Study on the relationship between PM2.5 concentration and visibility in Beijing based on light scattering theory

NASA Astrophysics Data System (ADS)

Yang, YuFeng; Li, Ting

2018-02-01

The study of the relationship between transmittance visibility and PM2.5 concentration under the haze conditions has important theoretical significance for Free Space Optical communication (FSO). In this paper, the influence of PM2.5 concentration on the transmittance, attenuation coefficient and visibility was studied by light scattering theory, and the results by Mie theory and Monte Carlo method were analyzed. At the same time, the effect of PM2.5 particle size distribution on visibility was also analyzed, and the visibility calculated by light scattering method was compared with the visibility measured in Beijing from 2014 to 2016. The result shows that the higher PM2.5 concentration is the more obvious the multiple scattering effect is. When the mass concentration of PM2.5 is constant, the larger the geometric mean of the particle diameter is, the larger the visibility is. By comparing the visibility measured and the visibility calculated, we can see that when PM2.5 concentration is higher than 100μg/m3 , PM2.5 is the main factor affecting the visibility; and when PM2.5 concentration is lower than 100μg/m3, other factors (such as PM10, wind speed, air pressure and gas molecules) should also need to be considered.

Obesity Increases Prevalence of Colonic Adenomas at Screening Colonoscopy: A Canadian Community-Based Study

PubMed Central

Chen, Grant I.; Devlin, Tim; Gibbs, Alison; Murray, Iain C.; Tran, Stanley; Weigensberg, Corey

2017-01-01

Background and Aims Obesity is a risk factor for colorectal neoplasia. We examined the influence of obesity and metabolic syndrome (MetS) on prevalence of neoplasia at screening colonoscopy. Methods We evaluated 2020 subjects undergoing first screening colonoscopy. Body mass index (BMI) was calculated at enrolment. Hyperlipidemia (HL), hypertension (HT), and diabetes mellitus (DM) were identified. Details of colonoscopy, polypectomy, and histology were recorded. Odds for adenomas (A) and advanced adenomas (ADV) in overweight (BMI 25.1–30) and obese (BMI > 30) subjects were assessed by multinomial regression, adjusted for covariates. Analyses included relationships between HL, HT, DM, age, tobacco usage, and neoplasia. Discriminatory power of HT, HL, DM, and BMI for neoplasia was assessed by binary logistic regression. Odds were calculated for neoplasia in each colonic segment related to BMI. Results A and ADV were commoner in overweight and obese males, obese females, older subjects, and smokers. HL, HT, and DM were associated with increased odds for neoplasia, significantly for A with hypertension. BMI alone predicted neoplasia as well as HT, HL, DM, or combinations thereof. All segments of the colon were affected. Multiple polyps were particularly prevalent in the obese. Conclusions Obesity and MetS are risk factors for colonic neoplasia in a Canadian population. PMID:28781966

Combined Quantum Chemical/Raman Spectroscopic Analyses of Li+ Cation Solvation: Cyclic Carbonate Solvents - Ethylene Carbonate and Propylene Earbonate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Allen, Joshua L.; Borodin, Oleg; Seo, D. M.

2014-12-01

Combined computational/Raman spectroscopic analyses of ethylene carbonate (EC) and propylene carbonate (PC) solvation interactions with lithium salts are reported. It is proposed that previously reported Raman analyses of (EC)n-LiX mixtures have utilized faulty assumptions. In the present studies, density functional theory (DFT) calculations have provided corrections in terms of both the scaling factors for the solvent's Raman band intensity variations and information about band overlap. By accounting for these factors, the solvation numbers obtained from two different EC solvent bands are in excellent agreement with one another. The same analysis for PC, however, was found to be quite challenging. Commerciallymore » available PC is a racemic mixture of (S)- and (R)-PC isomers. Based upon the quantum chemistry calculations, each of these solvent isomers may exist as multiple conformers due to a low energy barrier for ring inversion, making deconvolution of the Raman bands daunting and inherently prone to significant error. Thus, Raman spectroscopy is able to accurately determine the extent of the EC...Li+ cation solvation interactions using the provided methodology, but a similar analysis of PC...Li+ cation solvation results in a significant underestimation of the actual solvation numbers.« less

WebMOTIFS: automated discovery, filtering and scoring of DNA sequence motifs using multiple programs and Bayesian approaches

PubMed Central

Romer, Katherine A.; Kayombya, Guy-Richard; Fraenkel, Ernest

2007-01-01

WebMOTIFS provides a web interface that facilitates the discovery and analysis of DNA-sequence motifs. Several studies have shown that the accuracy of motif discovery can be significantly improved by using multiple de novo motif discovery programs and using randomized control calculations to identify the most significant motifs or by using Bayesian approaches. WebMOTIFS makes it easy to apply these strategies. Using a single submission form, users can run several motif discovery programs and score, cluster and visualize the results. In addition, the Bayesian motif discovery program THEME can be used to determine the class of transcription factors that is most likely to regulate a set of sequences. Input can be provided as a list of gene or probe identifiers. Used with the default settings, WebMOTIFS accurately identifies biologically relevant motifs from diverse data in several species. WebMOTIFS is freely available at http://fraenkel.mit.edu/webmotifs. PMID:17584794

Modest familial risks for multiple sclerosis: a registry-based study of the population of Sweden

PubMed Central

Westerlind, Helga; Ramanujam, Ryan; Uvehag, Daniel; Kuja-Halkola, Ralf; Boman, Marcus; Bottai, Matteo; Lichtenstein, Paul

2014-01-01

Data on familial recurrence rates of complex diseases such as multiple sclerosis give important hints to aetiological factors such as the importance of genes and environment. By linking national registries, we sought to avoid common limitations of clinic-based studies such as low numbers, poor representation of the population and selection bias. Through the Swedish Multiple Sclerosis Registry and a nationwide hospital registry, a total of 28 396 patients with multiple sclerosis were identified. We used the national Multi-Generation Registry to identify first and second degree relatives as well as cousins, and the Swedish Twin Registry to identify twins of patients with multiple sclerosis. Crude and age corrected familial risks were estimated for cases and found to be in the same range as previously published figures. Matched population-based controls were used to calculate relative risks, revealing lower estimates of familial multiple sclerosis risks than previously reported, with a sibling recurrence risk (λs = 7.1; 95% confidence interval: 6.42–7.86). Surprisingly, despite a well-established lower prevalence of multiple sclerosis amongst males, the relative risks were equal among maternal and paternal relations. A previously reported increased risk in maternal relations could thus not be replicated. An observed higher transmission rate from fathers to sons compared with mothers to sons suggested a higher transmission to offspring from the less prevalent sex; therefore, presence of the so-called ‘Carter effect’ could not be excluded. We estimated the heritability of multiple sclerosis using 74 757 twin pairs with known zygosity, of which 315 were affected with multiple sclerosis, and added information from 2.5 million sibling pairs to increase power. The heritability was estimated to be 0.64 (0.36–0.76), whereas the shared environmental component was estimated to be 0.01 (0.00–0.18). In summary, whereas multiple sclerosis is to a great extent an inherited trait, the familial relative risks may be lower than usually reported. PMID:24441172

The pQCT 'Bone Strength Indices' (BSIs, SSI). Relative mechanical impact and diagnostic value of the indicators of bone tissue and design quality employed in their calculation in healthy men and pre- and post-menopausal women.

PubMed

Cointry, G R; Ferretti, J L; Reina, P S; Nocciolino, L M; Rittweger, J; Capozza, R F

2014-03-01

The pQCT-assessed Bone Strength Indices (BSI's, SSI) depend on the product of a 'quality' indicator, the cortical vBMD (vCtD), and a 'design' indicator, one of the cross-sectional moments of inertia or related variables (MIs) in long bones. As the MIs vary naturally much more than the vCtD and represent different properties, it could be that the variation of the indices might not reflect the relative mechanical impact of the variation of their determinant factors in different individuals or circumstances. To understand this problem, we determined the vCtD and MI's in tibia scans of 232 healthy men and pre- and post-MP women, expressed in SD of the means calculated for each group, and analyzed the independent influence of 1 SD unit of variation of each factor on that of the indices by multiple correlations. Results showed: 1. that the independent influence of the MIs on the indices was generally larger than that of the vCtD, and 2. that in post-MP women the influence of the vCtD was larger than it was in the other groups. This confirms the view that inter-individual variation of vCtD is comparatively small, and that mechanical competence of human bone is mostly determined by 'design' factors.

Unscaled Bayes factors for multiple hypothesis testing in microarray experiments.

PubMed

Bertolino, Francesco; Cabras, Stefano; Castellanos, Maria Eugenia; Racugno, Walter

2015-12-01

Multiple hypothesis testing collects a series of techniques usually based on p-values as a summary of the available evidence from many statistical tests. In hypothesis testing, under a Bayesian perspective, the evidence for a specified hypothesis against an alternative, conditionally on data, is given by the Bayes factor. In this study, we approach multiple hypothesis testing based on both Bayes factors and p-values, regarding multiple hypothesis testing as a multiple model selection problem. To obtain the Bayes factors we assume default priors that are typically improper. In this case, the Bayes factor is usually undetermined due to the ratio of prior pseudo-constants. We show that ignoring prior pseudo-constants leads to unscaled Bayes factor which do not invalidate the inferential procedure in multiple hypothesis testing, because they are used within a comparative scheme. In fact, using partial information from the p-values, we are able to approximate the sampling null distribution of the unscaled Bayes factor and use it within Efron's multiple testing procedure. The simulation study suggests that under normal sampling model and even with small sample sizes, our approach provides false positive and false negative proportions that are less than other common multiple hypothesis testing approaches based only on p-values. The proposed procedure is illustrated in two simulation studies, and the advantages of its use are showed in the analysis of two microarray experiments. © The Author(s) 2011.

Determining the accuracy of maximum likelihood parameter estimates with colored residuals

NASA Technical Reports Server (NTRS)

Morelli, Eugene A.; Klein, Vladislav

1994-01-01

An important part of building high fidelity mathematical models based on measured data is calculating the accuracy associated with statistical estimates of the model parameters. Indeed, without some idea of the accuracy of parameter estimates, the estimates themselves have limited value. In this work, an expression based on theoretical analysis was developed to properly compute parameter accuracy measures for maximum likelihood estimates with colored residuals. This result is important because experience from the analysis of measured data reveals that the residuals from maximum likelihood estimation are almost always colored. The calculations involved can be appended to conventional maximum likelihood estimation algorithms. Simulated data runs were used to show that the parameter accuracy measures computed with this technique accurately reflect the quality of the parameter estimates from maximum likelihood estimation without the need for analysis of the output residuals in the frequency domain or heuristically determined multiplication factors. The result is general, although the application studied here is maximum likelihood estimation of aerodynamic model parameters from flight test data.

Bent Bonds and Multiple Bonds.

ERIC Educational Resources Information Center

Robinson, Edward A.; Gillespie, Ronald J.

1980-01-01

Considers carbon-carbon multiple bonds in terms of Pauling's bent bond model, which allows direct calculation of double and triple bonds from the length of a CC single bond. Lengths of these multiple bonds are estimated from direct measurements on "bent-bond" models constructed of plastic tubing and standard kits. (CS)

On the interpretation of the inverted kinetics equation and space-time calculations of the effectiveness of the VVER-1000 reactor scram system

NASA Astrophysics Data System (ADS)

Zizin, M. N.; Ivanov, L. D.

2013-12-01

In the present paper, an attempt is made to analyze the accuracy of calculating the effectiveness of the VVER-1000 reactor scram system by means of the inverted solution of the kinetics equation (ISKE). In the numerical studies in the intellectual ShIPR software system, the actuation of the reactor scram system with the possible jamming of one of the two most effective rods is simulated. First, the connection of functionals calculated in the space-time computation in different approximations with the kinetics equation is considered on the theoretical level. The formulas are presented in a manner facilitating their coding. Then, the results of processing of several such functions by the ISKE are presented. For estimating the effectiveness of the VVER-1000 reactor scram system, it is proposed to use the measured currents of ionization chambers (IC) jointly with calculated readings of IC imitators. In addition, the integral of the delayed neutron (DN) generation rate multiplied by the adjoint DN source over the volume of the reactor, calculated for the instant of time when insertion of safety rods ends, is used. This integral is necessary for taking into account the spatial reactivity effects. Reasonable agreement was attained for the considered example between the effectiveness of the scram system evaluated by this method and the values obtained by steady-state calculations as the difference of the reciprocal effective multiplication factors with withdrawn and inserted control rods. This agreement was attained with the use of eight-group DN parameters.

Child Maltreatment Among Singletons and Multiple Births in Japan: A Population-Based Study.

PubMed

Yokoyama, Yoshie; Oda, Terumi; Nagai, Noriyo; Sugimoto, Masako; Mizukami, Kenji

2015-12-01

The occurrence of multiple births has been recognized as a risk factor for child maltreatment. However, few population-based studies have examined the relationship between multiple births and child maltreatment. This study aimed to evaluate the degree of risk of child maltreatment among singletons and multiple births in Japan and to identify factors associated with increased risk. Using population-based data, we analyzed the database of records on child maltreatment and medical checkups for infants aged 1.5 years filed at Nishinomiya City Public Health Center between April 2007 and March 2011. To protect personal information, the data were transferred to anonymized electronic files for analysis. After adjusting by logistic regression for each associated factor and gestation number, multiples themselves were not associated with the risk of child maltreatment. However, compared with singletons, multiples had a significantly higher rate of risk factors for child maltreatment, including low birth weight and neural abnormality. Moreover, compared with mothers of singleton, mothers of twins had a significantly higher rate of poor health, which is a risk factor of child maltreatment. Multiples were not associated with the risk of child maltreatment. However, compared with singletons, multiples and their mothers had a significantly higher rate of risk factors of child maltreatment.

How to deal with multiple binding poses in alchemical relative protein-ligand binding free energy calculations.

PubMed

Kaus, Joseph W; Harder, Edward; Lin, Teng; Abel, Robert; McCammon, J Andrew; Wang, Lingle

2015-06-09

Recent advances in improved force fields and sampling methods have made it possible for the accurate calculation of protein–ligand binding free energies. Alchemical free energy perturbation (FEP) using an explicit solvent model is one of the most rigorous methods to calculate relative binding free energies. However, for cases where there are high energy barriers separating the relevant conformations that are important for ligand binding, the calculated free energy may depend on the initial conformation used in the simulation due to the lack of complete sampling of all the important regions in phase space. This is particularly true for ligands with multiple possible binding modes separated by high energy barriers, making it difficult to sample all relevant binding modes even with modern enhanced sampling methods. In this paper, we apply a previously developed method that provides a corrected binding free energy for ligands with multiple binding modes by combining the free energy results from multiple alchemical FEP calculations starting from all enumerated poses, and the results are compared with Glide docking and MM-GBSA calculations. From these calculations, the dominant ligand binding mode can also be predicted. We apply this method to a series of ligands that bind to c-Jun N-terminal kinase-1 (JNK1) and obtain improved free energy results. The dominant ligand binding modes predicted by this method agree with the available crystallography, while both Glide docking and MM-GBSA calculations incorrectly predict the binding modes for some ligands. The method also helps separate the force field error from the ligand sampling error, such that deviations in the predicted binding free energy from the experimental values likely indicate possible inaccuracies in the force field. An error in the force field for a subset of the ligands studied was identified using this method, and improved free energy results were obtained by correcting the partial charges assigned to the ligands. This improved the root-mean-square error (RMSE) for the predicted binding free energy from 1.9 kcal/mol with the original partial charges to 1.3 kcal/mol with the corrected partial charges.

How To Deal with Multiple Binding Poses in Alchemical Relative Protein–Ligand Binding Free Energy Calculations

PubMed Central

2016-01-01

Recent advances in improved force fields and sampling methods have made it possible for the accurate calculation of protein–ligand binding free energies. Alchemical free energy perturbation (FEP) using an explicit solvent model is one of the most rigorous methods to calculate relative binding free energies. However, for cases where there are high energy barriers separating the relevant conformations that are important for ligand binding, the calculated free energy may depend on the initial conformation used in the simulation due to the lack of complete sampling of all the important regions in phase space. This is particularly true for ligands with multiple possible binding modes separated by high energy barriers, making it difficult to sample all relevant binding modes even with modern enhanced sampling methods. In this paper, we apply a previously developed method that provides a corrected binding free energy for ligands with multiple binding modes by combining the free energy results from multiple alchemical FEP calculations starting from all enumerated poses, and the results are compared with Glide docking and MM-GBSA calculations. From these calculations, the dominant ligand binding mode can also be predicted. We apply this method to a series of ligands that bind to c-Jun N-terminal kinase-1 (JNK1) and obtain improved free energy results. The dominant ligand binding modes predicted by this method agree with the available crystallography, while both Glide docking and MM-GBSA calculations incorrectly predict the binding modes for some ligands. The method also helps separate the force field error from the ligand sampling error, such that deviations in the predicted binding free energy from the experimental values likely indicate possible inaccuracies in the force field. An error in the force field for a subset of the ligands studied was identified using this method, and improved free energy results were obtained by correcting the partial charges assigned to the ligands. This improved the root-mean-square error (RMSE) for the predicted binding free energy from 1.9 kcal/mol with the original partial charges to 1.3 kcal/mol with the corrected partial charges. PMID:26085821

Interface circuit for a multiple-beam tuning-fork gyroscope with high quality factors

NASA Astrophysics Data System (ADS)

Wang, Ren

This research work presents the design, theoretical analysis, fabrication, interface electronics, and experimental results of a Silicon-On-Insulator (SOI) based Multiple-Beam Tuning-Fork Gyroscope (MB-TFG). Based on a numerical model of Thermo-Elastic Damping (TED), a Multiple-Beam Tuning-Fork Structure (MB-TFS) is designed with high Quality factors (Qs) in its two operation modes. A comprehensive theoretical analysis of the MB-TFG design is conducted to relate the design parameters to its operation parameters and further performance parameters. In conjunction with a mask that defines the device through trenches to alleviate severe fabrication effect on anchor loss, a simple one-mask fabrication process is employed to implement this MB-TFG design on SOI wafers. The fabricated MB-TFGs are tested with PCB-level interface electronics and a thorough comparison between the experimental results and a theoretical analysis is conducted to verify the MB-TFG design and accurately interpret the measured performance. The highest measured Qs of the fabricated MB-TFGs in vacuum are 255,000 in the drive-mode and 103,000 in the sense-mode, at a frequency of 15.7kHz. Under a frequency difference of 4Hz between the two modes (operation frequency is 16.8kHz) and a drive-mode vibration amplitude of 3.0um, the measured rate sensitivity is 80mVpp/°/s with an equivalent impedance of 6MQ. The calculated overall rate resolution of this device is 0.37/hrhiElz, while the measured Angle Random Walk (ARW) and bias instability are 6.67°/'vhr and 95°/hr, respectively.

RF Exposure Analysis for Multiple Wi-Fi Devices In Enclosed Environment

NASA Technical Reports Server (NTRS)

Hwu, Shian U.; Rhodes, Bryan A.; deSilva, B. Kanishka; Sham, Catherine C.; Keiser, James R.

2013-01-01

Wi-Fi devices operated inside a metallic enclosure have been investigation in the recent years. A motivation for this study is to investigate wave propagation inside an enclosed environment such as elevator, car, aircraft, and spacecraft. There are performances and safety concerned that when the RF transmitters are used in the metallic enclosed environments. In this paper, the field distributions inside a confined room were investigated with multiple portable Wi-Fi devices. Computer simulations were performed using the rigorous computational electromagnetics (CEM). The method of moments (MoM) was used to model the mutual coupling among antennas. The geometrical theory of diffraction (GTD) was applied for the multiple reflections off the ground and walls. The prediction of the field distribution inside such environment is useful for the planning and deployment of a wireless radio and sensor system. Factors that affect the field strengths and distributions of radio waves in confined space were analyzed. The results could be used to evaluate the RF exposure safety in confined environment. By comparing the field distributions for various scenarios, it was observed that the Wi-Fi device counts, spacing and relative locations in the room are important factors in such environments. The RF Keep Out Zone (KOZ), where the electric field strengths exceed the permissible RF exposure limit, could be used to assess the RF human exposure compliance. As shown in this study, it s possible to maximize or minimize field intensity in specific area by arranging the Wi-Fi devices as a function of the relative location and spacing in a calculated manner.

The East London glaucoma prediction score: web-based validation of glaucoma risk screening tool

PubMed Central

Stephen, Cook; Benjamin, Longo-Mbenza

2013-01-01

AIM It is difficult for Optometrists and General Practitioners to know which patients are at risk. The East London glaucoma prediction score (ELGPS) is a web based risk calculator that has been developed to determine Glaucoma risk at the time of screening. Multiple risk factors that are available in a low tech environment are assessed to provide a risk assessment. This is extremely useful in settings where access to specialist care is difficult. Use of the calculator is educational. It is a free web based service. Data capture is user specific. METHOD The scoring system is a web based questionnaire that captures and subsequently calculates the relative risk for the presence of Glaucoma at the time of screening. Three categories of patient are described: Unlikely to have Glaucoma; Glaucoma Suspect and Glaucoma. A case review methodology of patients with known diagnosis is employed to validate the calculator risk assessment. RESULTS Data from the patient records of 400 patients with an established diagnosis has been captured and used to validate the screening tool. The website reports that the calculated diagnosis correlates with the actual diagnosis 82% of the time. Biostatistics analysis showed: Sensitivity = 88%; Positive predictive value = 97%; Specificity = 75%. CONCLUSION Analysis of the first 400 patients validates the web based screening tool as being a good method of screening for the at risk population. The validation is ongoing. The web based format will allow a more widespread recruitment for different geographic, population and personnel variables. PMID:23550097

Vernier effect-based multiplication of the Sagnac beating frequency in ring laser gyroscope sensors

NASA Astrophysics Data System (ADS)

Adib, George A.; Sabry, Yasser M.; Khalil, Diaa

2018-02-01

A multiplication method of the Sagnac effect scale factor in ring laser gyroscopes is presented based on the Vernier effect of a dual-coupler passive ring resonator coupled to the active ring. The multiplication occurs when the two rings have comparable lengths or integer multiples and their scale factors have opposite signs. In this case, and when the rings have similar areas, the scale factor is multiplied by ratio of their length to their length difference. The scale factor of the presented configuration is derived analytically and the lock-in effect is analyzed. The principle is demonstrated using optical fiber rings and semiconductor optical amplifier as gain medium. A scale factor multiplication by about 175 is experimentally measured, demonstrating larger than two orders of magnitude enhancement in the Sagnac effect scale factor for the first time in literature, up to the authors' knowledge.

49 CFR 1141.1 - Procedures to calculate interest rates.

Code of Federal Regulations, 2010 CFR

2010-10-01

... the portion of the year covered by the interest rate. A simple multiplication of the nominal rate by... 49 Transportation 8 2010-10-01 2010-10-01 false Procedures to calculate interest rates. 1141.1... TRANSPORTATION BOARD, DEPARTMENT OF TRANSPORTATION RULES OF PRACTICE PROCEDURES TO CALCULATE INTEREST RATES...

Using a Programmable Calculator to Teach Teophylline Pharmacokinetics.

ERIC Educational Resources Information Center

Closson, Richard Grant

1981-01-01

A calculator program for a Texas Instruments Model 59 to predict serum theophylline concentrations is described. The program accommodates the input of multiple dose times at irregular intervals, clearance changes due to concurrent patient diseases and age less than 17 years. The calculations for five hypothetical patients are given. (Author/MLW)

An effective method to accurately calculate the phase space factors for β - β - decay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neacsu, Andrei; Horoi, Mihai

2016-01-01

Accurate calculations of the electron phase space factors are necessary for reliable predictions of double-beta decay rates and for the analysis of the associated electron angular and energy distributions. Here, we present an effective method to calculate these phase space factors that takes into account the distorted Coulomb field of the daughter nucleus, yet it allows one to easily calculate the phase space factors with good accuracy relative to the most exact methods available in the recent literature.

Patient-based estimation of organ dose for a population of 58 adult patients across 13 protocol categories

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sahbaee, Pooyan, E-mail: psahbae@ncsu.edu; Segars, W. Paul; Samei, Ehsan

2014-07-15

Purpose: This study aimed to provide a comprehensive patient-specific organ dose estimation across a multiplicity of computed tomography (CT) examination protocols. Methods: A validated Monte Carlo program was employed to model a common CT system (LightSpeed VCT, GE Healthcare). The organ and effective doses were estimated from 13 commonly used body and neurological CT examination. The dose estimation was performed on 58 adult computational extended cardiac-torso phantoms (35 male, 23 female, mean age 51.5 years, mean weight 80.2 kg). The organ dose normalized by CTDI{sub vol} (h factor) and effective dose normalized by the dose length product (DLP) (k factor)more » were calculated from the results. A mathematical model was derived for the correlation between the h and k factors with the patient size across the protocols. Based on this mathematical model, a dose estimation iPhone operating system application was designed and developed to be used as a tool to estimate dose to the patients for a variety of routinely used CT examinations. Results: The organ dose results across all the protocols showed an exponential decrease with patient body size. The correlation was generally strong for the organs which were fully or partially located inside the scan coverage (Pearson sample correlation coefficient (r) of 0.49). The correlation was weaker for organs outside the scan coverage for which distance between the organ and the irradiation area was a stronger predictor of dose to the organ. For body protocols, the effective dose before and after normalization by DLP decreased exponentially with increasing patient's body diameter (r > 0.85). The exponential relationship between effective dose and patient's body diameter was significantly weaker for neurological protocols (r < 0.41), where the trunk length was a slightly stronger predictor of effective dose (0.15 < r < 0.46). Conclusions: While the most accurate estimation of a patient dose requires specific modeling of the patient anatomy, a first order approximation of organ and effective doses from routine CT scan protocols can be reasonably estimated using size specific factors. Estimation accuracy is generally poor for organ outside the scan range and for neurological protocols. The dose calculator designed in this study can be used to conveniently estimate and report the dose values for a patient across a multiplicity of CT scan protocols.« less

Risk factors of fatal occupational accidents in Iran.

PubMed

Asady, Hadi; Yaseri, Mehdi; Hosseini, Mostafa; Zarif-Yeganeh, Morvarid; Yousefifard, Mahmoud; Haghshenas, Mahin; Hajizadeh-Moghadam, Parisa

2018-01-01

Occupational accidents are of most important consequences of globalization in developing countries. Therefore, investigating the causes of occupational accidents for improving the job situation and making operational policy is necessary. So the aim of this study was to investigate factors affecting the fatal occupational accidents and also calculate the years of life lost for dead workers. This cross-sectional study was conducted on data related to the 6052 injured workers that was registered in the 2013 registry system of the Ministry of Health and Medical Education of Iran. Variables including sex, education, age, job tenure, injury cause, referred location of injured workers, occupation, shift work, season, accident day, damaged part of the body were chosen as independent variables. The Chi-squared and Fisher exact tests were used for univariate analysis and then exact multiple logistic regression was carried out to identify independent risk factors of fatal occupational accidents. Finally, for dead workers, years of life lost, according to the injury causes was calculated. Among the 6052 accidents reported, 33 deaths were recorded. Chi-square and Fisher exact tests showed that factors including: current job tenure ( p  = 0.01), damaged parts of the body ( p  < 0.001) and injury cause ( p  < 0.001) are associated with the fatal accidents. Also exact multiple logistic regression analysis showed a significant association between electric shocks as a cause of injury (OR = 7.04; 95% CI: 1.01-43.74; p  = 0.02) and current job tenure more than 1 year (OR = 0.21; 95% CI: 0.05-0.70; p  = 0.005) with the fatal accidents. The total amount of years of life lost based on causes of injuries was estimated 1289.12 years. In Iran, fatal accident odds in workers with job tenure more than 1 year was less in comparing to the workers with job tenure less and equal to 1 year. Also odd of death for electrical shock was more than other causes of injuries. So it seems that employing of workers who have more than one-year work experience in a specific job and using of appropriate safeguards will be useful for the reducing of fatal occupational accidents.

Theory and Application of Auger and Photoelectron Diffraction and Holography

NASA Astrophysics Data System (ADS)

Chen, Xiang

This dissertation addresses the theories and applications of three important surface analysis techniques: Auger electron diffraction (AED), x-ray photoelectron diffraction (XPD), and Auger and photoelectron holography. A full multiple-scattering scheme for the calculations of XPD, AED, and Kikuchi electron diffraction pattern from a surface cluster is described. It is used to simulate 64 eV M_{2,3}VV and 913 eV L_3VV AED patterns from Cu(001) surfaces, in order to test assertions in the literature that they are explicable by a classical "blocking" and channeling model. We find that this contention is not valid, and that only a quantum mechanical multiple-scattering calculation is able to simulate these patterns well. The same multiple scattering simulation scheme is also used to investigate the anomalous phenomena of peak shifts off the forward-scattering directions in photo -electron diffraction patterns of Mg KLL (1180 eV) and O 1s (955 eV) from MgO(001) surfaces. These shifts are explained by calculations assuming a short electron mean free path. Similar simulations of XPD from a CoSi_2(111) surface for Co-3p and Si-2p normal emission agree well with experimental diffraction patterns. A filtering process aimed at eliminating the self -interference effect in photoelectron holography is developed. A better reconstructed image from Si-2p XPD from a Si(001) (2 times 1) surface is seen at atomic resolution. A reconstruction algorithm which corrects for the anisotropic emitter waves as well as the anisotropic atomic scattering factors is used for holographic reconstruction from a Co-3p XPD pattern from a CoSi_2 surface. This new algorithm considerably improves the reconstructed image. Finally, a new reconstruction algorithm called "atomic position recovery by iterative optimization of reconstructed intensities" (APRIORI), which takes account of the self-interference terms omitted by the other holographic algorithms, is developed. Tests on a Ni-C-O chain and Si(111)(sqrt{3} times sqrt{3})B surface suggest that this new method may overcome the twin image problem in the traditional holographic methods, reduce the artifacts in real space, and even separately identify the chemical species of the scatterers.

Calculation of the Nucleon Axial Form Factor Using Staggered Lattice QCD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, Aaron S.; Hill, Richard J.; Kronfeld, Andreas S.

The nucleon axial form factor is a dominant contribution to errors in neutrino oscillation studies. Lattice QCD calculations can help control theory errors by providing first-principles information on nucleon form factors. In these proceedings, we present preliminary results on a blinded calculation ofmore » $$g_A$$ and the axial form factor using HISQ staggered baryons with 2+1+1 flavors of sea quarks. Calculations are done using physical light quark masses and are absolutely normalized. We discuss fitting form factor data with the model-independent $z$ expansion parametrization.« less

Relativistic corrections to the multiple scattering effect on the Sunyaev-Zel'dovich effect in the isotropic approximation

NASA Astrophysics Data System (ADS)

Itoh, Naoki; Kawana, Youhei; Nozawa, Satoshi; Kohyama, Yasuharu

2001-10-01

We extend the formalism for the calculation of the relativistic corrections to the Sunyaev-Zel'dovich effect for clusters of galaxies and include the multiple scattering effects in the isotropic approximation. We present the results of the calculations by the Fokker-Planck expansion method as well as by the direct numerical integration of the collision term of the Boltzmann equation. The multiple scattering contribution is found to be very small compared with the single scattering contribution. For high-temperature galaxy clusters of kBTe~15keV, the ratio of both the contributions is -0.2 per cent in the Wien region. In the Rayleigh-Jeans region the ratio is -0.03 per cent. Therefore the multiple scattering contribution is safely neglected for the observed galaxy clusters.

Compendium of energy-dependent sensitivity profiles for the TRX-2 thermal lattice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tomlinson, E.T.; Lucius, J.L.; Drischler, J.D.

1978-03-01

Energy-dependent sensitivity profiles for five responses calculated for the TRX-2 thermal lattice with the ORNL sensitivity code system FORSS are presented here both in graphical form and in SENPRO format. The responses are the multiplication factor, k/sub eff/; the ratio of epithermal-to-thermal captures in /sup 238/U, /sup 28/rho; the ratio of epithermal-to-thermal fissions in /sup 235/U, /sup 25/delta; the ratio of fissions in /sup 238/U to fissions in /sup 235/U, /sup 28/delta; and the ratio of captures in /sup 238/U to fissions in /sup 235/U, CR. A summary table of the total sensitivities is also presented.

Analysis of 238Pu and 56Fe Evaluated Data for Use in MYRRHA

NASA Astrophysics Data System (ADS)

Díez, C. J.; Cabellos, O.; Martínez, J. S.; Stankovskiy, A.; Van den Eynde, G.; Schillebeeckx, P.; Heyse, J.

2014-04-01

A sensitivity analysis on the multiplication factor, keff, to the cross section data has been carried out for the MYRRHA critical configuration in order to show the most relevant reactions. With these results, a further analysis on the 238Pu and 56Fe cross sections has been performed, comparing the evaluations provided in the JEFF-3.1.2 and ENDF/B-VII.1 libraries for these nuclides. Then, the effect in MYRRHA of the differences between evaluations are analysed, presenting the source of the differences. With these results, recommendations for the 56Fe and 238Pu evaluations are suggested. These calculations have been performed with SCALE6.1 and MCNPX-2.7e.

Validation of Hansen-Roach library for highly enriched uranium metal systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wenz, T.R.; Busch, R.D.

The Hansen-Roach 16-group cross-section library has been validated for use in pure uranium metal systems by modeling the Godiva critical assembly using the neutronics transport theory code ONEDANT to perform effective multiplication factor (k{sub eff}) calculations. The cross-section library used contains data for 118 isotopes (34 unique elements), including the revised cross sections for {sup 235}U and {sup 238}U. The Godiva critical assembly is a 17.4-cm sphere composed of 93.7 wt% {sup 235}U, 1.0 wt% {sup 234}U, and 5.3 wt% {sup 238}U with an effective homogeneous density of 18.7 g/cm{sup 3}.

High-Multiplicity Lead-Lead Interactions at 158 GeV/c per nucleon

NASA Technical Reports Server (NTRS)

Deines-Jones, P.; Cherry, M. L.; Dabrowska, A.; Holynski, R.; Jones, W. V.; Kolganova, E. D.; Kudzia, D.; Nilsen, B. S.; Olszewski, A.; Pozharova, E. A.;

Landslides and rock fall processes in the proglacial area of the Gepatsch glacier, Tyrol, Austria - Quantitative assessment of controlling factors and process rates

NASA Astrophysics Data System (ADS)

Vehling, Lucas; Rohn, Joachim; Moser, Michael

2013-04-01

Due to the rapid deglaciation since 1850, lithological structures and topoclimatic factors, mass movements like rock fall, landslides and complex processes are important contributing factors to sediment transport and modification of the earth's surface in the steep, high mountain catchment of the Gepatsch reservoir. Contemporary geotechnical processes, mass movement deposits, their source areas, and controlling factors like material properties and relief parameters are mapped in the field, on Orthofotos and on digital elevation models. The results are presented in an Arc-Gis based geotechnical map. All mapped mass movements are stored in an Arc-Gis geodatabase and can be queried regarding properties, volume and controlling factors, so that statistical analyses can be conducted. The assessment of rock wall retreat rates is carried out by three different methods in multiple locations, which differ in altitude, exposition, lithology and deglaciation time: Firstly, rock fall processes and rates are investigated in detail on five rock fall collector nets with an overall size of 750 m2. Rock fall particles are gathered, weighed and grain size distribution is detected by sieving and measuring the diameter of the particles to distinct between rock fall processes and magnitudes. Rock wall erosion processes like joint formation and expansions are measured with high temporal resolution by electrical crack meters, together with rock- and air temperature. Secondly, in cooperation with the other working groups in the PROSA project, rock fall volumes are determined with multitemporal terrestrial laserscanning from several locations. Lately, already triggered rock falls are accounted by mapping the volume of the deposit and calculating of the bedrock source area. The deposition time span is fixed by consideration of the late Holocene lateral moraines and analysing historical aerial photographs, so that longer term rock wall retreat rates can be calculated. In order to limit homogenous bedrock sections for calculating specific rock wall retreat rates and to extrapolate the local determinated rock wall retreat rates to larger scale, bedrock areas will be divided into units of similar morphodynamic intensities which will be therefore classified by a rock mass strength (RMS) system. The RMS-System contains lithological and topoclimatic factors but also takes the measured rock wall retreat rates into account.

Cross-Cultural Adaptation and Validation of the MPAM-R to Brazilian Portuguese and Proposal of a New Method to Calculate Factor Scores

PubMed Central

Albuquerque, Maicon R.; Lopes, Mariana C.; de Paula, Jonas J.; Faria, Larissa O.; Pereira, Eveline T.; da Costa, Varley T.

2017-01-01

In order to understand the reasons that lead individuals to practice physical activity, researchers developed the Motives for Physical Activity Measure-Revised (MPAM-R) scale. In 2010, a translation of MPAM-R to Portuguese and its validation was performed. However, psychometric measures were not acceptable. In addition, factor scores in some sports psychology scales are calculated by the mean of scores by items of the factor. Nevertheless, it seems appropriate that items with higher factor loadings, extracted by Factor Analysis, have greater weight in the factor score, as items with lower factor loadings have less weight in the factor score. The aims of the present study are to translate, validate the MPAM-R for Portuguese versions, and investigate agreement between two methods used to calculate factor scores. Three hundred volunteers who were involved in physical activity programs for at least 6 months were collected. Confirmatory Factor Analysis of the 30 items indicated that the version did not fit the model. After excluding four items, the final model with 26 items showed acceptable model fit measures by Exploratory Factor Analysis, as well as it conceptually supports the five factors as the original proposal. When two methods are compared to calculate factors scores, our results showed that only “Enjoyment” and “Appearance” factors showed agreement between methods to calculate factor scores. So, the Portuguese version of the MPAM-R can be used in a Brazilian context, and a new proposal for the calculation of the factor score seems to be promising. PMID:28293203

Sorting variables for each case: a new algorithm to calculate injury severity score (ISS) using SPSS-PC.

PubMed

Linn, S

One of the more often used measures of multiple injuries is the injury severity score (ISS). Determination of the ISS is based on the abbreviated injury scale (AIS). This paper suggests a new algorithm to sort the AISs for each case and calculate ISS. The program uses unsorted abbreviated injury scale (AIS) levels for each case and rearranges them in descending order. The first three sorted AISs representing the three most severe injuries of a person are then used to calculate injury severity score (ISS). This algorithm should be useful for analyses of clusters of injuries especially when more patients have multiple injuries.

Investigation of Photoluminescence and Photocurrent in InGaAsP/InP Strained Multiple Quantum Well Heterostructures

NASA Technical Reports Server (NTRS)

Raisky, O. Y.; Wang, W. B.; Alfano, R. R.; Reynolds, C. L., Jr.; Swaminathan, V.

1997-01-01

Multiple quantum well InGaAsP/InP p-i-n laser heterostructures with different barrier thicknesses have been investigated using photoluminescence (PL) and photocurrent (PC) measurements. The observed PL spectrum and peak positions are in good agreement with those obtained from transfer matrix calculations. Comparing the measured quantum well PC with calculated carrier escape rates, the photocurrent changes are found to be governed by the temperature dependence of the electron escape time.

Impact of Multiple Pharmacy Use on Medication Adherence and Drug-drug Interactions in Older Adults with Medicare Part D

PubMed Central

Marcum, Zachary A.; Driessen, Julia; Thorpe, Carolyn T.; Gellad, Walid F.; Donohue, Julie M.

2014-01-01

Objective To assess the association between multiple pharmacy use and medication adherence and potential drug-drug interactions (DDIs) among older adults. Design, Setting, and Participants Cross-sectional propensity score-weighted analysis of 2009 claims data from a nationally representative sample of 926,956 Medicare Part D beneficiaries aged >65 continuously enrolled in fee-for-service Medicare and Part D that year, and filled >1 prescription at a community/retail or mail order pharmacy. Multiple pharmacy use was defined as concurrent (overlapping time periods) or sequential use (non-overlapping time periods) of >2 pharmacies in the year. Measurements Medication adherence was calculated using a proportion of days covered ≥0.80 for eight therapeutic categories (β-blockers, renin angiotensin system antagonists, calcium channel blockers, statins, sulfonylureas, biguanides [i.e., metformin], thiazolidinediones, and dipeptidyl peptidase-IV inhibitors). Potential DDIs arising from use of certain drugs across a broad set of classes were defined as the concurrent filling of two interacting drugs. Results Overall, 38.1% of the sample used multiple pharmacies. Those using multiple pharmacies (both concurrently and sequentially) consistently had higher adjusted odds of non-adherence (ranging from 1.10 to 1.31, p<0.001) across all chronic medication classes assessed after controlling for socio-demographic, health status and access to care factors, compared to single pharmacy users. The adjusted predicted probability of exposure to a DDI was also slightly higher for those using multiple pharmacies concurrently (3.6%) compared to single pharmacy users (3.2%, AOR 1.11, 95% CI 1.08–1.15) but lower in individuals using multiple pharmacies sequentially (2.8%, AOR 0.85, 95% CI 0.81–0.91). Conclusions Filling prescriptions at multiple pharmacies was associated with lower medication adherence across multiple chronic medications, and a small but statistically significant increase in DDIs among concurrent pharmacy users. PMID:24521363

GIS-technologies application for calculation of potential soil loss of Marha River basin (Republic of Saha)

NASA Astrophysics Data System (ADS)

Shynbergenov, Y.; Maltsev, K.; Sihanova, N.

2018-01-01

In the article the presentation of estimation methods of potential soil loss in the conditions of Siberia with application of geographical information systems is resulted. For the reference area of the Marha river basin, which is a part of the Lena river catchment, there was created a specialized geographic information database of potential soil erosion, with scale of 1: 1,000,000. Digital elevation model “GMTED2010” and the hydroset layer corresponding to the scale of 1: 1,000,000 are taken to calculate the soil loss values. The formation of the geobase data is considered in detail being constructed on the basis of the multiplicative structure which reflects the main parameters of the relief (slope steepness, exposition, slope length, erosion potential of the relief), soil, climatic characteristics and modern types of land cover. At the quantitative level with sufficiently high degree of spatial detail results were obtained for calculating the potential erosion of soils. The average value of potential soil loss in the basin without taking into account the factor of land cover types, was 12.6 t/ha/yr. The calculations carried out, taking into account the types of land cover obtained from remote sensing data from outer space resulted in an appreciable reduction of the soil loss values (0.04 t/ha/yr.).

Advanced Neutronics Tools for BWR Design Calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Santamarina, A.; Hfaiedh, N.; Letellier, R.

2006-07-01

This paper summarizes the developments implemented in the new APOLLO2.8 neutronics tool to meet the required target accuracy in LWR applications, particularly void effects and pin-by-pin power map in BWRs. The Method Of Characteristics was developed to allow efficient LWR assembly calculations in 2D-exact heterogeneous geometry; resonant reaction calculation was improved by the optimized SHEM-281 group mesh, which avoids resonance self-shielding approximation below 23 eV, and the new space-dependent method for resonant mixture that accounts for resonance overlapping. Furthermore, a new library CEA2005, processed from JEFF3.1 evaluations involving feedback from Critical Experiments and LWR P.I.E, is used. The specific '2005-2007more » BWR Plan' settled to demonstrate the validation/qualification of this neutronics tool is described. Some results from the validation process are presented: the comparison of APOLLO2.8 results to reference Monte Carlo TRIPOLI4 results on specific BWR benchmarks emphasizes the ability of the deterministic tool to calculate BWR assembly multiplication factor within 200 pcm accuracy for void fraction varying from 0 to 100%. The qualification process against the BASALA mock-up experiment stresses APOLLO2.8/CEA2005 performances: pin-by-pin power is always predicted within 2% accuracy, reactivity worth of B4C or Hf cruciform control blade, as well as Gd pins, is predicted within 1.2% accuracy. (authors)« less

Accelerated rescaling of single Monte Carlo simulation runs with the Graphics Processing Unit (GPU).

PubMed

Yang, Owen; Choi, Bernard

2013-01-01

To interpret fiber-based and camera-based measurements of remitted light from biological tissues, researchers typically use analytical models, such as the diffusion approximation to light transport theory, or stochastic models, such as Monte Carlo modeling. To achieve rapid (ideally real-time) measurement of tissue optical properties, especially in clinical situations, there is a critical need to accelerate Monte Carlo simulation runs. In this manuscript, we report on our approach using the Graphics Processing Unit (GPU) to accelerate rescaling of single Monte Carlo runs to calculate rapidly diffuse reflectance values for different sets of tissue optical properties. We selected MATLAB to enable non-specialists in C and CUDA-based programming to use the generated open-source code. We developed a software package with four abstraction layers. To calculate a set of diffuse reflectance values from a simulated tissue with homogeneous optical properties, our rescaling GPU-based approach achieves a reduction in computation time of several orders of magnitude as compared to other GPU-based approaches. Specifically, our GPU-based approach generated a diffuse reflectance value in 0.08ms. The transfer time from CPU to GPU memory currently is a limiting factor with GPU-based calculations. However, for calculation of multiple diffuse reflectance values, our GPU-based approach still can lead to processing that is ~3400 times faster than other GPU-based approaches.

Multiple stressors and amphibian declines: dual impacts of pesticides and fish on yellow-legged frogs.

PubMed

Davidson, Carlos; Knapp, Roland A

2007-03-01

More than 40% of Earth's 5700+ amphibian species have undergone recent declines. Despite the likely involvement of multiple factors in driving these declines, most studies continue to focus on single stressors. In California (USA), separate studies have implicated either introduced fish or pesticides as causal agents. To date, however, no study has simultaneously evaluated the respective roles of these two potential stressors nor attempted to assess their relative importance, information critical for the development of effective conservation efforts and environmental policies. We examined the role and relative effect of fish and pesticides on the mountain yellow-legged frog (Rana muscosa) using unusually detailed data sets for a large portion of R. muscosa's historic range in California's Sierra Nevada. Habitat characteristics and presence/absence of R. muscosa and fish were quantified at each of 6831 sites during field surveys. Pesticide use upwind of each site was calculated from pesticide application records and predominant wind directions. Using generalized additive models, we found that, after accounting for habitat effects, the probability of R. muscosa presence was significantly reduced by both fish and pesticides, with the landscape-scale effect of pesticides much stronger than that of fish. The degree to which a site was sheltered from the predominant wind (and associated pesticides) was also a significant predictor of R. muscosa presence. Taken together, these results represent the strongest evidence to date that windborne pesticides are contributing to amphibian declines in pristine locations. Our results suggest that amphibian declines may have complex multi-factorial causes, and caution that single-factor studies that demonstrate the importance of one factor should not be used as evidence against the importance of other factors.

Infection after pacemaker implantation: infection rates and risk factors associated with infection in a population-based cohort study of 46299 consecutive patients

PubMed Central

Johansen, Jens Brock; Jørgensen, Ole Dan; Møller, Mogens; Arnsbo, Per; Mortensen, Peter Thomas; Nielsen, Jens Cosedis

2011-01-01

Aims Infection is a serious complication of pacemaker (PM) systems. Although the rate of infection has been debated, the figures are largely unknown. We therefore studied the incidence of PM infection and its associated risk factors in the Danish population. Methods and results Since 1982, all PM implantation and removal procedures performed in Denmark have been prospectively recorded in the Danish Pacemaker Register. All patients (n = 46299) who underwent implantation between 1982 and 2007 were included. The total length of surveillance was 236 888 PM-years. The incidence of infection was calculated according to the total number of PM-years. The incidence of surgical site infection (≤365 days after PM implantation) was compared with later infection in first implant and replacement procedures. Multiple-record and multiple-event-per-subject proportional hazards analyses were used to identify the independent risk factors of PM infection. Surgical site infection occurred in 192 cases after first implantation (incidence rate 4.82/1000 PM-years), and in 133 cases after replacement (12.12/1000 PM-years). Infections occurring more than 365 days after the first implantation occurred in 153 cases (1.02/1000 PM-years), and in 118 cases after replacement (3.26/1000 PM-years). Independent factors associated with an increased risk of PM infection were a greater number of PM operations (including replacements), male sex, younger age, implantation during the earliest part of the study period, and absence of antibiotics (P< 0.001). Conclusion The overall risk of infection after PM implantation was low. A greater number of operations augmented the risk of infection. This should be taken into account when considering revisions of PM systems. PMID:21252172

Risk factors for acute knee injury in female youth football.

PubMed

Hägglund, Martin; Waldén, Markus

2016-03-01

To prospectively evaluate risk factors for acute time-loss knee injury, in particular ACL injury, in female youth football players. Risk factors were studied in 4556 players aged 12-17 years from a randomised controlled trial during the 2009 season. Covariates were both intrinsic (body mass index, age, relative age effect, onset of menarche, previous acute knee injury or ACL injury, current knee complaints, and familial disposition of ACL injury) and extrinsic (no. of training sessions/week, no. of matches/week, match exposure ratio, match play with other teams, and artificial turf exposure). Hazard ratios (HRs) and 95% confidence intervals (CIs) were calculated from individual variable and multiple Cox regression analyses. Ninety-six acute knee injuries were recorded, 21 of them ACL injuries. Multiple Cox regression showed a fourfold higher ACL injury rate for players with familial disposition of ACL injury (HR 3.57; 95% CI 1.48-8.62). Significant predictor variables for acute knee injury were age >14 years (HR 1.97; 95% CI 1.30-2.97), knee complaints at the start of the season (HR 1.98; 95% CI 1.30-3.02), and familial disposition of ACL injury (HR 1.96; 95% CI 1.22-3.16). No differences in injury rates were seen when playing on artificial turf compared with natural grass. Female youth football players with a familial disposition of ACL injury had an increased risk of ACL injury and acute knee injury. Older players and those with knee complaints at pre-season were more at risk of acute knee injury. Although the predictive values were low, these factors could be used in athlete screening to target preventive interventions. II.

Interaction of a genetic risk score with physical activity, physical inactivity, and body mass index in relation to venous thromboembolism risk.

PubMed

Kim, Jihye; Kraft, Peter; Hagan, Kaitlin A; Harrington, Laura B; Lindstroem, Sara; Kabrhel, Christopher

2018-06-01

Venous thromboembolism (VTE) is highly heritable. Physical activity, physical inactivity and body mass index (BMI) are also risk factors, but evidence of interaction between genetic and environmental risk factors is limited. Data on 2,134 VTE cases and 3,890 matched controls were obtained from the Nurses' Health Study (NHS), Nurses' Health Study II (NHS II), and Health Professionals Follow-up Study (HPFS). We calculated a weighted genetic risk score (wGRS) using 16 single nucleotide polymorphisms associated with VTE risk in published genome-wide association studies (GWAS). Data on three risk factors, physical activity (metabolic equivalent [MET] hours per week), physical inactivity (sitting hours per week) and BMI, were obtained from biennial questionnaires. VTE cases were incident since cohort inception; controls were matched to cases on age, cohort, and genotype array. Using conditional logistic regression, we assessed joint effects and interaction effects on both additive and multiplicative scales. We also ran models using continuous wGRS stratified by risk-factor categories. We observed a supra-additive interaction between wGRS and BMI. Having both high wGRS and high BMI was associated with a 3.4-fold greater risk of VTE (relative excess risk due to interaction = 0.69, p = 0.046). However, we did not find evidence for a multiplicative interaction with BMI. No interactions were observed for physical activity or inactivity. We found a synergetic effect between a genetic risk score and high BMI on the risk of VTE. Intervention efforts lowering BMI to decrease VTE risk may have particularly large beneficial effects among individuals with high genetic risk. © 2018 WILEY PERIODICALS, INC.

The preferred magnetic resonance imaging planes in quantifying visceral adipose tissue and evaluating cardiovascular risk.

PubMed

Liu, K H; Chan, Y L; Chan, J C N; Chan, W B; Kong, M O; Poon, M Y

2005-09-01

Magnetic Resonance Imaging (MRI) is a well-accepted non-invasive method in the quantification of visceral adipose tissue. However, a standard method of measurement has not yet been universally agreed. The objectives of the present study were 2-fold, firstly, to identify the imaging plane in the Chinese population which gives the best correlation with total visceral adipose tissue volume and cardiovascular risk factors; and secondly to compare the correlations between single-slice and multiple-slice approach with cardiovascular risk factors. Thirty-seven Chinese subjects with no known medical history underwent MRI examination for quantifying total visceral adipose tissue volume. The visceral adipose tissue area at five axial imaging levels within abdomen and pelvis were determined. All subjects had blood pressure measured and fasting blood taken for analysis of cardiovascular risk factors. Framingham risk score for each subject was calculated. The imaging plane at the level of 'lower costal margin' (LCM) in both men and women had the highest correlation with total visceral adipose tissue volume (r = 0.97 and 0.99 respectively). The visceral adipose tissue area at specific imaging levels showed higher correlations with various cardiovascular risk factors and Framingham risk score than total visceral adipose tissue volume. The visceral adipose tissue area at 'umbilicus' (UMB) level in men (r = 0.88) and LCM level in women (r = 0.70) showed the best correlation with Framingham risk score. The imaging plane at the level of LCM is preferred for reflecting total visceral adipose tissue volume in Chinese subjects. For investigating the association of cardiovascular risk with visceral adipose tissue in MRI-obesity research, the single-slice approach is superior to the multiple-slice approach, with the level of UMB in men and LCM in women as the preferred imaging planes.

Adiponectin Provides Additional Information to Conventional Cardiovascular Risk Factors for Assessing the Risk of Atherosclerosis in Both Genders

PubMed Central

Yoon, Jin-Ha; Kim, Sung-Kyung; Choi, Ho-June; Choi, Soo-In; Cha, So-Youn; Koh, Sang-Baek

2013-01-01

Background This study evaluated the relation between adiponectin and atherosclerosis in both genders, and investigated whether adiponectin provides useful additional information for assessing the risk of atherosclerosis. Methods We measured serum adiponectin levels and other cardiovascular risk factors in 1033 subjects (454 men, 579 women) from the Korean Genomic Rural Cohort study. Carotid intima–media-thickness (CIMT) was used as measure of atherosclerosis. Odds ratios (ORs) with 95% confidence intervals (95% CI) were calculated using multiple logistic regression, and receiver operating characteristic curves (ROC), the category-free net reclassification improvement (NRI) and integrated discrimination improvement (IDI) were calculated. Results After adjustment for conventional cardiovascular risk factors, such as age, waist circumference, smoking history, low-density and high-density lipoprotein cholesterol, triglycerides, systolic blood pressure and insulin resistance, the ORs (95%CI) of the third tertile adiponectin group were 0.42 (0.25–0.72) in men and 0.47 (0.29–0.75) in women. The area under the curve (AUC) on the ROC analysis increased significantly by 0.025 in men and 0.022 in women when adiponectin was added to the logistic model of conventional cardiovascular risk factors (AUC in men: 0.655 to 0.680, p = 0.038; AUC in women: 0.654 to 0.676, p = 0.041). The NRI was 0.32 (95%CI: 0.13–0.50, p<0.001), and the IDI was 0.03 (95%CI: 0.01–0.04, p<0.001) for men. For women, the category-free NRI was 0.18 (95%CI: 0.02–0.34, p = 0.031) and the IDI was 0.003 (95%CI: −0.002–0.008, p = 0.189). Conclusion Adiponectin and atherosclerosis were significantly related in both genders, and these relationships were independent of conventional cardiovascular risk factors. Furthermore, adiponectin provided additional information to conventional cardiovascular risk factors regarding the risk of atherosclerosis. PMID:24116054

Adiponectin provides additional information to conventional cardiovascular risk factors for assessing the risk of atherosclerosis in both genders.

PubMed

Yoon, Jin-Ha; Kim, Sung-Kyung; Choi, Ho-June; Choi, Soo-In; Cha, So-Youn; Koh, Sang-Baek; Kang, Hee-Taik; Ahn, Song Vogue

2013-01-01

This study evaluated the relation between adiponectin and atherosclerosis in both genders, and investigated whether adiponectin provides useful additional information for assessing the risk of atherosclerosis. We measured serum adiponectin levels and other cardiovascular risk factors in 1033 subjects (454 men, 579 women) from the Korean Genomic Rural Cohort study. Carotid intima-media-thickness (CIMT) was used as measure of atherosclerosis. Odds ratios (ORs) with 95% confidence intervals (95% CI) were calculated using multiple logistic regression, and receiver operating characteristic curves (ROC), the category-free net reclassification improvement (NRI) and integrated discrimination improvement (IDI) were calculated. After adjustment for conventional cardiovascular risk factors, such as age, waist circumference, smoking history, low-density and high-density lipoprotein cholesterol, triglycerides, systolic blood pressure and insulin resistance, the ORs (95%CI) of the third tertile adiponectin group were 0.42 (0.25-0.72) in men and 0.47 (0.29-0.75) in women. The area under the curve (AUC) on the ROC analysis increased significantly by 0.025 in men and 0.022 in women when adiponectin was added to the logistic model of conventional cardiovascular risk factors (AUC in men: 0.655 to 0.680, p = 0.038; AUC in women: 0.654 to 0.676, p = 0.041). The NRI was 0.32 (95%CI: 0.13-0.50, p<0.001), and the IDI was 0.03 (95%CI: 0.01-0.04, p<0.001) for men. For women, the category-free NRI was 0.18 (95%CI: 0.02-0.34, p = 0.031) and the IDI was 0.003 (95%CI: -0.002-0.008, p = 0.189). Adiponectin and atherosclerosis were significantly related in both genders, and these relationships were independent of conventional cardiovascular risk factors. Furthermore, adiponectin provided additional information to conventional cardiovascular risk factors regarding the risk of atherosclerosis.

Multilocus lod scores in large pedigrees: combination of exact and approximate calculations.

PubMed

Tong, Liping; Thompson, Elizabeth

2008-01-01

To detect the positions of disease loci, lod scores are calculated at multiple chromosomal positions given trait and marker data on members of pedigrees. Exact lod score calculations are often impossible when the size of the pedigree and the number of markers are both large. In this case, a Markov Chain Monte Carlo (MCMC) approach provides an approximation. However, to provide accurate results, mixing performance is always a key issue in these MCMC methods. In this paper, we propose two methods to improve MCMC sampling and hence obtain more accurate lod score estimates in shorter computation time. The first improvement generalizes the block-Gibbs meiosis (M) sampler to multiple meiosis (MM) sampler in which multiple meioses are updated jointly, across all loci. The second one divides the computations on a large pedigree into several parts by conditioning on the haplotypes of some 'key' individuals. We perform exact calculations for the descendant parts where more data are often available, and combine this information with sampling of the hidden variables in the ancestral parts. Our approaches are expected to be most useful for data on a large pedigree with a lot of missing data. (c) 2007 S. Karger AG, Basel

Multilocus Lod Scores in Large Pedigrees: Combination of Exact and Approximate Calculations

PubMed Central

Tong, Liping; Thompson, Elizabeth

2007-01-01

To detect the positions of disease loci, lod scores are calculated at multiple chromosomal positions given trait and marker data on members of pedigrees. Exact lod score calculations are often impossible when the size of the pedigree and the number of markers are both large. In this case, a Markov Chain Monte Carlo (MCMC) approach provides an approximation. However, to provide accurate results, mixing performance is always a key issue in these MCMC methods. In this paper, we propose two methods to improve MCMC sampling and hence obtain more accurate lod score estimates in shorter computation time. The first improvement generalizes the block-Gibbs meiosis (M) sampler to multiple meiosis (MM) sampler in which multiple meioses are updated jointly, across all loci. The second one divides the computations on a large pedigree into several parts by conditioning on the haplotypes of some ‘key’ individuals. We perform exact calculations for the descendant parts where more data are often available, and combine this information with sampling of the hidden variables in the ancestral parts. Our approaches are expected to be most useful for data on a large pedigree with a lot of missing data. PMID:17934317

Structural reliability calculation method based on the dual neural network and direct integration method.

PubMed

Li, Haibin; He, Yun; Nie, Xiaobo

2018-01-01

Structural reliability analysis under uncertainty is paid wide attention by engineers and scholars due to reflecting the structural characteristics and the bearing actual situation. The direct integration method, started from the definition of reliability theory, is easy to be understood, but there are still mathematics difficulties in the calculation of multiple integrals. Therefore, a dual neural network method is proposed for calculating multiple integrals in this paper. Dual neural network consists of two neural networks. The neural network A is used to learn the integrand function, and the neural network B is used to simulate the original function. According to the derivative relationships between the network output and the network input, the neural network B is derived from the neural network A. On this basis, the performance function of normalization is employed in the proposed method to overcome the difficulty of multiple integrations and to improve the accuracy for reliability calculations. The comparisons between the proposed method and Monte Carlo simulation method, Hasofer-Lind method, the mean value first-order second moment method have demonstrated that the proposed method is an efficient and accurate reliability method for structural reliability problems.

ADHD and math - The differential effect on calculation and estimation.

PubMed

Ganor-Stern, Dana; Steinhorn, Ofir

2018-05-31

Adults with ADHD were compared to controls when solving multiplication problems exactly and when estimating the results of multidigit multiplication problems relative to reference numbers. The ADHD participants were slower than controls in the exact calculation and in the estimation tasks, but not less accurate. The ADHD participants were similar to controls in showing enhanced accuracy and speed for smaller problem sizes, for trials in which the reference numbers were smaller (vs. larger) than the exact answers and for reference numbers that were far (vs. close) from the exact answer. The two groups similarly used the approximated calculation and the sense of magnitude strategies. They differed however in strategy execution, mainly of the approximated calculation strategy, which requires working memory resources. The increase in reaction time associated with using the approximated calculation strategy was larger for the ADHD compared to the control participants. Thus, ADHD seems to selectively impair calculation processes in estimation tasks that rely on working memory, but it does not hamper estimation skills that are based on sense of magnitude. The educational implications of these findings are discussed. Copyright © 2018. Published by Elsevier B.V.

Exploring Hill Ciphers with Graphing Calculators.

ERIC Educational Resources Information Center

St. John, Dennis

1998-01-01

Explains how to code and decode messages using Hill ciphers which combine matrix multiplication and modular arithmetic. Discusses how a graphing calculator can facilitate the matrix and modular arithmetic used in the coding and decoding procedures. (ASK)

Anisotropy of the angular distribution of fission fragments in heavy-ion fusion-fission reactions: The influence of the level-density parameter and the neck thickness

NASA Astrophysics Data System (ADS)

Naderi, D.; Pahlavani, M. R.; Alavi, S. A.

2013-05-01

Using the Langevin dynamical approach, the neutron multiplicity and the anisotropy of angular distribution of fission fragments in heavy ion fusion-fission reactions were calculated. We applied one- and two-dimensional Langevin equations to study the decay of a hot excited compound nucleus. The influence of the level-density parameter on neutron multiplicity and anisotropy of angular distribution of fission fragments was investigated. We used the level-density parameter based on the liquid drop model with two different values of the Bartel approach and Pomorska approach. Our calculations show that the anisotropy and neutron multiplicity are affected by level-density parameter and neck thickness. The calculations were performed on the 16O+208Pb and 20Ne+209Bi reactions. Obtained results in the case of the two-dimensional Langevin with a level-density parameter based on Bartel and co-workers approach are in better agreement with experimental data.

Chronic disease and chronic disease risk factors among First Nations, Inuit and Métis populations of northern Canada.

PubMed

Bruce, S G; Riediger, N D; Lix, L M

2014-11-01

Aboriginal populations in northern Canada are experiencing rapid changes in their environments, which may negatively impact on health status. The purpose of our study was to compare chronic conditions and risk factors in northern Aboriginal populations, including First Nations (FN), Inuit and Métis populations, and northern non-Aboriginal populations. Data were from the Canadian Community Health Survey for the period from 2005 to 2008. Weighted multiple logistic regression models tested the association between ethnic groups and health outcomes. Model covariates were age, sex, territory of residence, education and income. Odds ratios (ORs) are reported and a bootstrap method calculated 95% confidence intervals (CIs) and p values. Odds of having at least one chronic condition was significantly lower for the Inuit (OR = 0.59; 95% CI: 0.43-0.81) than for non-Aboriginal population, but similar among FN, Métis and non-Aboriginal populations. Prevalence of many risk factors was significantly different for Inuit, FN and Métis populations. Aboriginal populations in Canada's north have heterogeneous health status. Continued chronic disease and risk factor surveillance will be important to monitor changes over time and to evaluate the impact of public health interventions.

The prevalence, characteristics, and factors associated with purchasing Chinese herbal medicine among adults in Taiwan.

PubMed

Shih, Chun -Chuan; Huang, Lu-Hsiang; Yeh, Chun-Chieh; Lane, Hsin-Long; Hsieh, Chang-Ju; Tsai, Chin-Chuan; Lin, Li-Wei; Chen, Ta-Liang; Liao, Chien-Chang

2017-03-27

The objective of this study was to investigate the prevalence and factors associated with purchasing Chinese herbal medicine (CHM) without a physician's prescription among adults. Using data from the 2005 National Health Interview Survey and National Health Insurance, we identified 16,756 individuals aged 20 years and older. Socio-demographic factors, lifestyle, medical services utilization and health behaviors were compared between people with and without a history of purchasing CHM by calculating adjusted odds ratios (ORs) and 95% confidence intervals (CIs) in a multiple logistic regression analysis. The one-month prevalence of purchasing CHM without a physician' prescription was 5.2% in Taiwan. People more likely to purchase CHM included people aged ≥70 years (OR 2.84, 95% CI 2.03-3.99), women (OR 1.28, 95% CI 1.11-1.48), non-indigenous people (OR 2.61, 95% CI 1.29-5.30), and people with an illness not receiving medical care (OR 2.69, 95% CI 2.19-3.31). The prevalence of purchasing CHM without a physician's prescription is high in Taiwan and is correlated with factors such as socio-demographics, disease history, and behaviors surrounding the utilization of medical care.

Dietary and demographic correlates of serum ß-glucuronidase activity

PubMed Central

Maruti, Sonia S.; Li, Lin; Chang, Jyh-Lurn; Prunty, JoAnn; Schwarz, Yvonne; Li, Shuying S.; King, Irena B.; Potter, John D.; Lampe, Johanna W.

2010-01-01

Background β-glucuronidase, an acid hydrolase that deconjugates glucuronides, may increase cancer risk; however, little is known about factors associated with human β-glucuronidase. Objective To examine whether dietary and demographic factors were associated with serum β-glucuronidase activity. Design We conducted a cross-sectional study among 279 healthy men and women, aged 20-40 years. Diet, categorized by botanical families and nutrient intakes, was assessed from 3-day food records and a validated semiquantitative food frequency questionnaire. Demographic factors were directly measured or self-reported. Adjusted mean β-glucuronidase activity across categories of exposure variables were calculated by multiple linear regression. Results Higher β-glucuronidase activity was significantly associated with being male, older age (≥30 years), non-Caucasian, overweight (≥ 25 kg/m2), and higher intakes of gamma-tocopherol. Conversely, lower β-glucuronidase activity was significantly associated with higher intakes of calcium, iron, and magnesium. A suggestive decrease in β-glucuronidase activity was observed for the botanical families, Cruciferae, Rutaceae, Compositae, Roseaceae, and Umbelliferae, but tests for trend were not statistically significant. Conclusions Several dietary and nondietary factors were associated with β-glucuronidase activity, however confirmation of these associations are needed. PMID:20099195

[Sexual behaviour among adolescents in Brazzaville, Congo].

PubMed

Mabiala Babela, J-R; Massamba, A; Bantsimba, T; Senga, P

2008-09-01

Estimate sexual activity among Congolese adolescents in Brazzaville and appreciate the influence of sociocultural and economic factors on sexual behaviour. Data were collected from 900 adolescents (389 males and 511 females) aged 10-19 years in the seven urban areas of Brazzaville. These subjects were randomly recruited by a two stage sampling. The data were gathered by an anonymous face-to-face questionnaire. Relative risk estimations were calculated for early or first sexual intercourse, multiple sexual partnerness and safe sex. A total of 474 respondents indicated that they were sexually active. Females were more sexually active, 270 compared with 204 males (p<0.05). The mean early age of coital debut was 14.6 years (S.D.=1.7 years). Early intercourse (before 14 years) was found in 73 males and 39 females (p<0.001). Multiple sexual partnerness was found in 81.3% of males, while the frequency of females was 51.1%. Risk factors for pregnancy and multiple sexual partnerness were unemployment mother, non school situation, early puberty and non sexual education. In contrast, regular religious activity was recognized as factor that had significant protection impact on sexual activity. The total use ratio of the condom was estimated at 42.2% in males. More females (41.7%) were using Ogino method of contraception. In addition, 102 females (36.8%) claimed to have already a pregnancy and the mean age was 16.1 years (S.D.=1.2 years). In 64.7% of these cases, teenagers chose the abortion as solution of an unwanted pregnancy. After the birth of a child, it was reported that 82.4% of adolescents gave up with school. Our results show the importance of problems associated to sexual activity among Congolese adolescents in Middle Africa. These data should be taken into account when planning the prevention of risk of sexual behaviours among adolescents.

Family History of Sudden Cardiac Death of the Young: Prevalence and Associated Factors

PubMed Central

White, Michelle J.; Duquette, Debra; Bach, Janice; Rafferty, Ann P.; Fussman, Chris; Sharangpani, Ruta; Russell, Mark W.

2015-01-01

Sudden cardiac death of the young (SCDY) is a devastating event for families and communities. Family history is a significant risk factor for this potentially preventable cause of death, however a complete and detailed family history is not commonly obtained during routine health maintenance visits. To estimate the proportion of adults with a family history of SCDY, the Michigan Department of Health and Human Services (MDHHS) Genomics Program included two questions within the 2007 Michigan Behavioral Risk Factor Survey (MiBRFS). Prevalence estimates and 95% confidence intervals were calculated. Among adults in Michigan, 6.3% reported a family history of SCDY, with a greater prevalence among blacks, those with lower household income, and those with less education. Among those reporting a family history of SCDY, 42.3% had at least one first-degree relative and 26.2% had multiple affected family members. This is the first study to demonstrate the prevalence of family history of SCDY while also highlighting key sociodemographic characteristics associated with increased prevalence. These findings should guide evidence-based interventions to reach those at greatest risk. PMID:27417815

Study on Commercialization of Biogasification Systems in Ishikari Bay New Port Area - Proposal of Estimation Method of Collectable Amount of Food Waste by using Binary Logit Model -

NASA Astrophysics Data System (ADS)

Watanabe, Sho; Furuichi, Toru; Ishii, Kazuei

This study proposed an estimation method for collectable amount of food waste considering the food waste generator's cooperation ratio ant the amount of food waste generation, and clarified the factors influencing the collectable amount of food waste. In our method, the cooperation ratio was calculated by using the binary logit model which is often used for the traffic multiple choice question. In order to develop a more precise binary logit model, the factors influencing on the cooperation ratio were extracted by a questionnaire survey asking food waste generator's intention, and the preference investigation was then conducted at the second step. As a result, the collectable amount of food waste was estimated to be 72 [t/day] in the Ishikari bay new port area under a condition of current collection system by using our method. In addition, the most critical factor influencing on the collectable amount of food waste was the treatment fee for households, and was the permitted mixture degree of improper materials for retail trade and restaurant businesses

Numerical Computation of Homogeneous Slope Stability

PubMed Central

Xiao, Shuangshuang; Li, Kemin; Ding, Xiaohua; Liu, Tong

2015-01-01

To simplify the computational process of homogeneous slope stability, improve computational accuracy, and find multiple potential slip surfaces of a complex geometric slope, this study utilized the limit equilibrium method to derive expression equations of overall and partial factors of safety. This study transformed the solution of the minimum factor of safety (FOS) to solving of a constrained nonlinear programming problem and applied an exhaustive method (EM) and particle swarm optimization algorithm (PSO) to this problem. In simple slope examples, the computational results using an EM and PSO were close to those obtained using other methods. Compared to the EM, the PSO had a small computation error and a significantly shorter computation time. As a result, the PSO could precisely calculate the slope FOS with high efficiency. The example of the multistage slope analysis indicated that this slope had two potential slip surfaces. The factors of safety were 1.1182 and 1.1560, respectively. The differences between these and the minimum FOS (1.0759) were small, but the positions of the slip surfaces were completely different than the critical slip surface (CSS). PMID:25784927

Numerical computation of homogeneous slope stability.

PubMed

Xiao, Shuangshuang; Li, Kemin; Ding, Xiaohua; Liu, Tong

2015-01-01

To simplify the computational process of homogeneous slope stability, improve computational accuracy, and find multiple potential slip surfaces of a complex geometric slope, this study utilized the limit equilibrium method to derive expression equations of overall and partial factors of safety. This study transformed the solution of the minimum factor of safety (FOS) to solving of a constrained nonlinear programming problem and applied an exhaustive method (EM) and particle swarm optimization algorithm (PSO) to this problem. In simple slope examples, the computational results using an EM and PSO were close to those obtained using other methods. Compared to the EM, the PSO had a small computation error and a significantly shorter computation time. As a result, the PSO could precisely calculate the slope FOS with high efficiency. The example of the multistage slope analysis indicated that this slope had two potential slip surfaces. The factors of safety were 1.1182 and 1.1560, respectively. The differences between these and the minimum FOS (1.0759) were small, but the positions of the slip surfaces were completely different than the critical slip surface (CSS).

[The choice of the type of design in the clinical investigation studies. Case and control studies].

PubMed

Posada de la Paz, M

2004-09-01

Case-control studies are appropriate designs in neurology sciences to search for risk factors that have already occurred in a group of patients. In them, the subjects are selected on the basis of whether they have the disease or not and then they are compared in regards to the risk factor or prognosis investigated. These sorts of designs can be performed in a shorter and cheaper way than the regular cohort studies. They are appropriate for the evaluation of rare diseases and can examine multiple etiological factors for a single disease. On the contrary, they are not so efficient when rare exposures are involved. Incidence rates in exposed and non-exposed subjects cannot be calculated and on some occasions, the timing between exposure and outcome can be very difficult to establish. The Odds Ratio and its confident intervals is the measurement used for estimating the risk strength in this design. The clinical neurologist should be familiar with these terms, given the frequency of case-control studies described in neurology science literature, and should know their principal advantages and limitations.

C-reactive protein in relation to early atherosclerosis and periodontitis.

PubMed

Yakob, Maha; Meurman, Jukka H; Jogestrand, Tomas; Nowak, Jacek; Söder, Per-Östen; Söder, Birgitta

2012-02-01

Periodontitis may affect atherosclerosis via the chronic inflammation. We investigated high-sensitivity C-reactive protein (hsCRP) in relation to early vascular atherosclerotic changes in non-symptomatic subjects with and without long-term periodontitis. Carotid ultrasonography with calculation of common carotid artery intima-media area (cIMA) was performed, and hsCRP and atherosclerosis risk factors were analysed in randomly chosen 93 patients with periodontitis and 41 controls. The relationship between hsCRP, cIMA and atherosclerosis risk factors was evaluated with multiple logistic regression analysis. Women displayed lower hsCRP (p < 0.05) and higher serum HDL (p < 0.001) than men. In all patients with periodontitis, cIMA values were higher than in controls. Periodontitis appeared to be a major predictor for increased cIMA (odds ratio, 3.82; 95% confidence interval, 1.19-12.26). Neither of these factors was significantly associated with hsCRP which thus appeared not sensitive enough to be a marker for periodontitis or atherosclerosis. Hence, irrespective of low hsCRP levels, periodontitis appeared to increase the risk for atherosclerosis.

Reliability and Validity of the Physical Education Activities Scale.

PubMed

Thomason, Diane L; Feng, Du

2016-06-01

Measuring adolescent perceptions of physical education (PE) activities is necessary in understanding determinants of school PE activity participation. This study assessed reliability and validity of the Physical Education Activities Scale (PEAS), a 41-item visual analog scale measuring high school adolescent perceptions of school PE activity participation. Adolescents (N = 529) from the Pacific Northwest aged 15-19 in grades 9-12 participated in the study. Construct validity was assessed using exploratory factor analysis (EFA) and confirmatory factor analysis (CFA). Measurement invariance across sex groups was tested by multiple-group CFA. Internal consistency reliability was analyzed using Cronbach's alpha. Inter-subscale correlations (Pearson's r) were calculated for latent factors and observed subscale scores. Exploratory factor analysis suggested a 3-factor solution explaining 43.4% of the total variance. Confirmatory factor analysis showed the 3-factor model fit the data adequately (comparative fit index [CFI] = 0.90, Tucker-Lewis index [TLI] = 0.89, root mean squared error of approximation [RMSEA] = 0.063). Factorial invariance was supported. Cronbach's alpha of the total PEAS was α = 0.92, and for subscales α ranged from 0.65 to 0.92. Independent t-tests showed significantly higher mean scores for boys than girls on the total scale and all subscales. Findings provide psychometric support for using the PEAS for examining adolescent's psychosocial and environmental perceptions to participating in PE activities. © 2016, American School Health Association.

Hauser-Feshbach fission fragment de-excitation with calculated macroscopic-microscopic mass yields

NASA Astrophysics Data System (ADS)

Jaffke, Patrick; Möller, Peter; Talou, Patrick; Sierk, Arnold J.

2018-03-01

The Hauser-Feshbach statistical model is applied to the de-excitation of primary fission fragments using input mass yields calculated with macroscopic-microscopic models of the potential energy surface. We test the sensitivity of the prompt fission observables to the input mass yields for two important reactions, 235U(nth,f ) and 239Pu(nth,f ) , for which good experimental data exist. General traits of the mass yields, such as the location of the peaks and their widths, can impact both the prompt neutron and γ -ray multiplicities, as well as their spectra. Specifically, we use several mass yields to determine a linear correlation between the calculated prompt neutron multiplicity ν ¯ and the average heavy-fragment mass 〈Ah〉 of the input mass yields ∂ ν ¯/∂ 〈Ah〉 =±0.1 (n /f ) /u . The mass peak width influences the correlation between the total kinetic energy of the fission fragments and the total number of prompt neutrons emitted, ν¯T(TKE ) . Typical biases on prompt particle observables from using calculated mass yields instead of experimental ones are δ ν ¯=4 % for the average prompt neutron multiplicity, δ M ¯γ=1 % for the average prompt γ -ray multiplicity, δ ɛ¯nLAB=1 % for the average outgoing neutron energy, δ ɛ¯γ=1 % for the average γ -ray energy, and δ 〈TKE 〉=0.4 % for the average total kinetic energy of the fission fragments.

Theory of Multiple Coulomb Scattering from Extended Nuclei

DOE R&D Accomplishments Database

Cooper, L. N.; Rainwater, J.

1954-08-01

Two independent methods are described for calculating the multiple scattering distribution for projected angle scattering resulting when very high energy charged particles traverse a thick scatterer. The results are compared with the theories of Moliere and Olbert.

Utilization of combined remote sensing techniques to detect environmental variables influencing malaria vector densities in rural West Africa

PubMed Central

2012-01-01

Introduction The use of remote sensing has found its way into the field of epidemiology within the last decades. With the increased sensor resolution of recent and future satellites new possibilities emerge for high resolution risk modeling and risk mapping. Methods A SPOT 5 satellite image, taken during the rainy season 2009 was used for calculating indices by combining the image's spectral bands. Besides the widely used Normalized Difference Vegetation Index (NDVI) other indices were tested for significant correlation against field observations. Multiple steps, including the detection of surface water, its breeding appropriateness for Anopheles and modeling of vector imagines abundance, were performed. Data collection on larvae, adult vectors and geographic parameters in the field, was amended by using remote sensing techniques to gather data on altitude (Digital Elevation Model = DEM), precipitation (Tropical Rainfall Measurement Mission = TRMM), land surface temperatures (LST). Results The DEM derived altitude as well as indices calculations combining the satellite's spectral bands (NDTI = Normalized Difference Turbidity Index, NDWI Mac Feeters = Normalized Difference Water Index) turned out to be reliable indicators for surface water in the local geographic setting. While Anopheles larvae abundance in habitats is driven by multiple, interconnected factors - amongst which the NDVI - and precipitation events, the presence of vector imagines was found to be correlated negatively to remotely sensed LST and positively to the cumulated amount of rainfall in the preceding 15 days and to the Normalized Difference Pond Index (NDPI) within the 500 m buffer zone around capture points. Conclusions Remotely sensed geographical and meteorological factors, including precipitations, temperature, as well as vegetation, humidity and land cover indicators could be used as explanatory variables for surface water presence, larval development and imagines densities. This modeling approach based on remotely sensed information is potentially useful for counter measures that are putting on at the environmental side, namely vector larvae control via larviciding and water body reforming. PMID:22443452

Utilization of combined remote sensing techniques to detect environmental variables influencing malaria vector densities in rural West Africa.

PubMed

Dambach, Peter; Machault, Vanessa; Lacaux, Jean-Pierre; Vignolles, Cécile; Sié, Ali; Sauerborn, Rainer

2012-03-23

The use of remote sensing has found its way into the field of epidemiology within the last decades. With the increased sensor resolution of recent and future satellites new possibilities emerge for high resolution risk modeling and risk mapping. A SPOT 5 satellite image, taken during the rainy season 2009 was used for calculating indices by combining the image's spectral bands. Besides the widely used Normalized Difference Vegetation Index (NDVI) other indices were tested for significant correlation against field observations. Multiple steps, including the detection of surface water, its breeding appropriateness for Anopheles and modeling of vector imagines abundance, were performed. Data collection on larvae, adult vectors and geographic parameters in the field, was amended by using remote sensing techniques to gather data on altitude (Digital Elevation Model = DEM), precipitation (Tropical Rainfall Measurement Mission = TRMM), land surface temperatures (LST). The DEM derived altitude as well as indices calculations combining the satellite's spectral bands (NDTI = Normalized Difference Turbidity Index, NDWI Mac Feeters = Normalized Difference Water Index) turned out to be reliable indicators for surface water in the local geographic setting. While Anopheles larvae abundance in habitats is driven by multiple, interconnected factors - amongst which the NDVI - and precipitation events, the presence of vector imagines was found to be correlated negatively to remotely sensed LST and positively to the cumulated amount of rainfall in the preceding 15 days and to the Normalized Difference Pond Index (NDPI) within the 500 m buffer zone around capture points. Remotely sensed geographical and meteorological factors, including precipitations, temperature, as well as vegetation, humidity and land cover indicators could be used as explanatory variables for surface water presence, larval development and imagines densities. This modeling approach based on remotely sensed information is potentially useful for counter measures that are putting on at the environmental side, namely vector larvae control via larviciding and water body reforming. © 2012 Dambach et al; licensee BioMed Central Ltd.

Agility performance in high-level junior basketball players: the predictive value of anthropometrics and power qualities.

PubMed

Sisic, Nedim; Jelicic, Mario; Pehar, Miran; Spasic, Miodrag; Sekulic, Damir

2016-01-01

In basketball, anthropometric status is an important factor when identifying and selecting talents, while agility is one of the most vital motor performances. The aim of this investigation was to evaluate the influence of anthropometric variables and power capacities on different preplanned agility performances. The participants were 92 high-level, junior-age basketball players (16-17 years of age; 187.6±8.72 cm in body height, 78.40±12.26 kg in body mass), randomly divided into a validation and cross-validation subsample. The predictors set consisted of 16 anthropometric variables, three tests of power-capacities (Sargent-jump, broad-jump and medicine-ball-throw) as predictors. The criteria were three tests of agility: a T-Shape-Test; a Zig-Zag-Test, and a test of running with a 180-degree turn (T180). Forward stepwise multiple regressions were calculated for validation subsamples and then cross-validated. Cross validation included correlations between observed and predicted scores, dependent samples t-test between predicted and observed scores; and Bland Altman graphics. Analysis of the variance identified centres being advanced in most of the anthropometric indices, and medicine-ball-throw (all at P<0.05); with no significant between-position-differences for other studied motor performances. Multiple regression models originally calculated for the validation subsample were then cross-validated, and confirmed for Zig-zag-Test (R of 0.71 and 0.72 for the validation and cross-validation subsample, respectively). Anthropometrics were not strongly related to agility performance, but leg length is found to be negatively associated with performance in basketball-specific agility. Power capacities are confirmed to be an important factor in agility. The results highlighted the importance of sport-specific tests when studying pre-planned agility performance in basketball. The improvement in power capacities will probably result in an improvement in agility in basketball athletes, while anthropometric indices should be used in order to identify those athletes who can achieve superior agility performance.

Analysis of the accuracy and precision of the McMaster method in detection of the eggs of Toxocara and Trichuris species (Nematoda) in dog faeces.

PubMed

Kochanowski, Maciej; Dabrowska, Joanna; Karamon, Jacek; Cencek, Tomasz; Osiński, Zbigniew

2013-07-01

The aim of this study was to determine the accuracy and precision of McMaster method with Raynaud's modification in the detection of the eggs of the nematodes Toxocara canis (Werner, 1782) and Trichuris ovis (Abildgaard, 1795) in faeces of dogs. Four variants of McMaster method were used for counting: in one grid, two grids, the whole McMaster chamber and flotation in the tube. One hundred sixty samples were prepared from dog faeces (20 repetitions for each egg quantity) containing 15, 25, 50, 100, 150, 200, 250 and 300 eggs of T. canis and T. ovis in 1 g of faeces. To compare the influence of kind of faeces on the results, samples of dog faeces were enriched at the same levels with the eggs of another nematode, Ascaris suum Goeze, 1782. In addition, 160 samples of pig faeces were prepared and enriched only with A. suum eggs in the same way. The highest limit of detection (the lowest level of eggs that were detected in at least 50% of repetitions) in all McMaster chamber variants were obtained for T. canis eggs (25-250 eggs/g faeces). In the variant with flotation in the tube, the highest limit of detection was obtained for T. ovis eggs (100 eggs/g). The best results of the limit of detection, sensitivity and the lowest coefficients of variation were obtained with the use of the whole McMaster chamber variant. There was no significant impact of properties of faeces on the obtained results. Multiplication factors for the whole chamber were calculated on the basis of the transformed equation of the regression line, illustrating the relationship between the number of detected eggs and that of the eggs added to the'sample. Multiplication factors calculated for T. canis and T. ovis eggs were higher than those expected using McMaster method with Raynaud modification.

Mars Exploration Rover Pancam Photometric Data QUBs: Definition and Example Uses.

NASA Astrophysics Data System (ADS)

Soderblom, J. M.; Bell, J. F.; Arvidson, R. E.; Johnson, J. R.; Johnson, M. J.; Seelos, F. P.

2004-12-01

Pancam multi-spectral observations acquired at the Mars Exploration Rover Spirit and Opportunity landing sites are being assembled into a multi-layer format know as a QUB. For any given pixel in a Pancam image the QUB will contain values for the radiance factor, incidence (i), emission (e), and phase (g) angles, X, Y, and Z distance in a rover-based coordinate system, disparity in number of pixels between the left and right eye images and range data. Good range data is required for the generation of a Pancam QUB. The radiance factor (I/F, where I is the measured scene radiance on sensor and π F is the incident solar irradiance) is calculated using a combination of preflight calibration data and information obtained from near-simultaneous observations of an onboard reflectance calibration target. The range, X, Y, Z and disparity data, and i, e, and g are calculated using routines developed by JPL's MIPL and Cornell. When possible, these data have been interpolated to maximize parameter coverage; a map of non-interpolated data is also included in each QUB. QUBs should prove very useful in photometric studies (e.g., Johnson et al.; Seelos, et al., this conference), detailed spectral analyses (e.g., Bell et al., this conference), and detailed topographic/DTM studies. Here we present two examples of the utilization of the information contained in Pancam QUBs. In one example we remove the photometric variability from spectra collected from multiple facets of a rock using knowledge of i, e, g and derived photometric functions. This is necessary if one wishes to conduct comparative studies of observations acquired under varying geometries and lighting conditions. In another example we present an analysis using the discrete ordinate multiple scattering radiative transfer code DISORT where we separate the atmosphere and surface contributions of the surface reflectance.

3D CSEM inversion based on goal-oriented adaptive finite element method

NASA Astrophysics Data System (ADS)

Zhang, Y.; Key, K.

2016-12-01

We present a parallel 3D frequency domain controlled-source electromagnetic inversion code name MARE3DEM. Non-linear inversion of observed data is performed with the Occam variant of regularized Gauss-Newton optimization. The forward operator is based on the goal-oriented finite element method that efficiently calculates the responses and sensitivity kernels in parallel using a data decomposition scheme where independent modeling tasks contain different frequencies and subsets of the transmitters and receivers. To accommodate complex 3D conductivity variation with high flexibility and precision, we adopt the dual-grid approach where the forward mesh conforms to the inversion parameter grid and is adaptively refined until the forward solution converges to the desired accuracy. This dual-grid approach is memory efficient, since the inverse parameter grid remains independent from fine meshing generated around the transmitter and receivers by the adaptive finite element method. Besides, the unstructured inverse mesh efficiently handles multiple scale structures and allows for fine-scale model parameters within the region of interest. Our mesh generation engine keeps track of the refinement hierarchy so that the map of conductivity and sensitivity kernel between the forward and inverse mesh is retained. We employ the adjoint-reciprocity method to calculate the sensitivity kernels which establish a linear relationship between changes in the conductivity model and changes in the modeled responses. Our code uses a direcy solver for the linear systems, so the adjoint problem is efficiently computed by re-using the factorization from the primary problem. Further computational efficiency and scalability is obtained in the regularized Gauss-Newton portion of the inversion using parallel dense matrix-matrix multiplication and matrix factorization routines implemented with the ScaLAPACK library. We show the scalability, reliability and the potential of the algorithm to deal with complex geological scenarios by applying it to the inversion of synthetic marine controlled source EM data generated for a complex 3D offshore model with significant seafloor topography.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stathakis, S; Defoor, D; Saenz, D

Purpose: Stereotactic radiosurgery (SRS) outcomes are related to the delivered dose to the target and to surrounding tissue. We have commissioned a Monte Carlo based dose calculation algorithm to recalculated the delivered dose planned using pencil beam calculation dose engine. Methods: Twenty consecutive previously treated patients have been selected for this study. All plans were generated using the iPlan treatment planning system (TPS) and calculated using the pencil beam algorithm. Each patient plan consisted of 1 to 3 targets and treated using dynamically conformal arcs or intensity modulated beams. Multi-target treatments were delivered using multiple isocenters, one for each target.more » These plans were recalculated for the purpose of this study using a single isocenter. The CT image sets along with the plan, doses and structures were DICOM exported to Monaco TPS and the dose was recalculated using the same voxel resolution and monitor units. Benchmark data was also generated prior to patient calculations to assess the accuracy of the two TPS against measurements using a micro ionization chamber in solid water. Results: Good agreement, within −0.4% for Monaco and +2.2% for iPlan were observed for measurements in water phantom. Doses in patient geometry revealed up to 9.6% differences for single target plans and 9.3% for multiple-target-multiple-isocenter plans. The average dose differences for multi-target-single-isocenter plans were approximately 1.4%. Similar differences were observed for the OARs and integral dose. Conclusion: Accuracy of the beam is crucial for the dose calculation especially in the case of small fields such as those used in SRS treatments. A superior dose calculation algorithm such as Monte Carlo, with properly commissioned beam models, which is unaffected by the lack of electronic equilibrium should be preferred for the calculation of small fields to improve accuracy.« less

Lunar Advanced Volatile Analysis Subsystem: Pressure Transducer Trade Study

NASA Technical Reports Server (NTRS)

Kang, Edward Shinuk

2017-01-01

In Situ Resource Utilization (ISRU) is a key factor in paving the way for the future of human space exploration. The ability to harvest resources on foreign astronomical objects to produce consumables and propellant offers potential reduction in mission cost and risk. Through previous missions, the existence of water ice at the poles of the moon has been identified, however the feasibility of water extraction for resources remains unanswered. The Resource Prospector (RP) mission is currently in development to provide ground truth, and will enable us to characterize the distribution of water at one of the lunar poles. Regolith & Environment Science and Oxygen & Lunar Volatile Extraction (RESOLVE) is the primary payload on RP that will be used in conjunction with a rover. RESOLVE contains multiple instruments for systematically identifying the presence of water. The main process involves the use of two systems within RESOLVE: the Oxygen Volatile Extraction Node (OVEN) and Lunar Advanced Volatile Analysis (LAVA). Within the LAVA subsystem, there are multiple calculations that depend on accurate pressure readings. One of the most important instances where pressure transducers (PT) are used is for calculating the number of moles in a gas transfer from the OVEN subsystem. As a critical component of the main process, a mixture of custom and commercial off the shelf (COTS) PTs are currently being tested in the expected operating environment to eventually down select an option for integrated testing in the LAVA engineering test unit (ETU).

Multiscale weighted colored graphs for protein flexibility and rigidity analysis

NASA Astrophysics Data System (ADS)

Bramer, David; Wei, Guo-Wei

2018-02-01

Protein structural fluctuation, measured by Debye-Waller factors or B-factors, is known to correlate to protein flexibility and function. A variety of methods has been developed for protein Debye-Waller factor prediction and related applications to domain separation, docking pose ranking, entropy calculation, hinge detection, stability analysis, etc. Nevertheless, none of the current methodologies are able to deliver an accuracy of 0.7 in terms of the Pearson correlation coefficients averaged over a large set of proteins. In this work, we introduce a paradigm-shifting geometric graph model, multiscale weighted colored graph (MWCG), to provide a new generation of computational algorithms to significantly change the current status of protein structural fluctuation analysis. Our MWCG model divides a protein graph into multiple subgraphs based on interaction types between graph nodes and represents the protein rigidity by generalized centralities of subgraphs. MWCGs not only predict the B-factors of protein residues but also accurately analyze the flexibility of all atoms in a protein. The MWCG model is validated over a number of protein test sets and compared with many standard methods. An extensive numerical study indicates that the proposed MWCG offers an accuracy of over 0.8 and thus provides perhaps the first reliable method for estimating protein flexibility and B-factors. It also simultaneously predicts all-atom flexibility in a molecule.

Attitudes Toward Seeking Professional Psychological Help: Factor Structure and Socio-Demographic Predictors

PubMed Central

Picco, Louisa; Abdin, Edimanysah; Chong, Siow Ann; Pang, Shirlene; Shafie, Saleha; Chua, Boon Yiang; Vaingankar, Janhavi A.; Ong, Lue Ping; Tay, Jenny; Subramaniam, Mythily

2016-01-01

Attitudes toward seeking professional psychological help (ATSPPH) are complex. Help seeking preferences are influenced by various attitudinal and socio-demographic factors and can often result in unmet needs, treatment gaps, and delays in help-seeking. The aims of the current study were to explore the factor structure of the ATSPPH short form (-SF) scale and determine whether any significant socio-demographic differences exist in terms of help-seeking attitudes. Data were extracted from a population-based survey conducted among Singapore residents aged 18–65 years. Respondents provided socio-demographic information and were administered the ATSPPH-SF. Weighted mean and standard error of the mean were calculated for continuous variables, and frequencies and percentages for categorical variables. Confirmatory factor analysis and exploratory factor analysis were performed to establish the validity of the factor structure of the ATSPPH-SF scale. Multivariable linear regressions were conducted to examine predictors of each of the ATSPPH-SF factors. The factor analysis revealed that the ATSPPH-SF formed three distinct dimensions: “Openness to seeking professional help,” “Value in seeking professional help,” and “Preference to cope on one's own.” Multiple linear regression analyses showed that age, ethnicity, marital status, education, and income were significantly associated with the ATSPPH-SF factors. Population subgroups that were less open to or saw less value in seeking psychological help should be targeted via culturally appropriate education campaigns and tailored and supportive interventions. PMID:27199794

Multiple roles and all-cause mortality: the Japan Collaborative Cohort Study.

PubMed

Tamakoshi, Akiko; Ikeda, Ai; Fujino, Yoshihisa; Tamakoshi, Koji; Iso, Hisoyasu

2013-02-01

Two contrasting perspectives on the effects of multiple roles; the 'role overload hypothesis' and the 'role enhancement model', have been proposed to predict variations in health. The aim of this study was to evaluate the impact of multiple roles on all-cause mortality in Japan where gender roles are currently changing. A total of 76,758 individuals from the Japan Collaborative Cohort Study were followed for an average of 15.7 years. Hazard ratios (HRs) with 95% confidence intervals were calculated from proportional hazard models to estimate the risk of all-cause mortality according to multiple roles (spouse, parent and worker, and combinations of these roles). After adjusting for potential confounding factors, the risks of all-cause mortality were elevated among men and women without a role. The number of roles was also associated with all-cause mortality risk, showing the highest risk values among those with no roles compared with those with triple roles (HR: 1.66 in men and 1.78 in women). The impact of the lack of a role was generally greater in men than in women and also in the middle-aged than in the elderly. A beneficial effect of multiple roles was suggested among Japanese. The fewer roles they had, the higher all-cause mortality risks were observed. The risk values of those with fewer roles were generally higher in men than in women and also in the middle-aged than in the elderly, partially explained by greater role overload in middle-aged women than other groups in Japan.

DNA repair variants and breast cancer risk.

PubMed

Grundy, Anne; Richardson, Harriet; Schuetz, Johanna M; Burstyn, Igor; Spinelli, John J; Brooks-Wilson, Angela; Aronson, Kristan J

2016-05-01

A functional DNA repair system has been identified as important in the prevention of tumour development. Previous studies have hypothesized that common polymorphisms in DNA repair genes could play a role in breast cancer risk and also identified the potential for interactions between these polymorphisms and established breast cancer risk factors such as physical activity. Associations with breast cancer risk for 99 single nucleotide polymorphisms (SNPs) from genes in ten DNA repair pathways were examined in a case-control study including both Europeans (644 cases, 809 controls) and East Asians (299 cases, 160 controls). Odds ratios in both additive and dominant genetic models were calculated separately for participants of European and East Asian ancestry using multivariate logistic regression. The impact of multiple comparisons was assessed by correcting for the false discovery rate within each DNA repair pathway. Interactions between several breast cancer risk factors and DNA repair SNPs were also evaluated. One SNP (rs3213282) in the gene XRCC1 was associated with an increased risk of breast cancer in the dominant model of inheritance following adjustment for the false discovery rate (P < 0.05), although no associations were observed for other DNA repair SNPs. Interactions of six SNPs in multiple DNA repair pathways with physical activity were evident prior to correction for FDR, following which there was support for only one of the interaction terms (P < 0.05). No consistent associations between variants in DNA repair genes and breast cancer risk or their modification by breast cancer risk factors were observed. © 2016 Wiley Periodicals, Inc.

Sasang Constitution as a Risk Factor for Diabetes Mellitus: A Cross-Sectional Study

PubMed Central

Lee, Tae-Gyu; Koh, Byunghee

2009-01-01

Sasang Constitutional Medicine, which is a branch of traditional Korean medicine, states that medications for diabetes should be individualized according to the patient's individual constitution. However, the effect of constitution on diabetes has not been evaluated to date. Therefore, this study was conducted to determine if constitution is an independent risk factor for diabetes by comparing the prevalence and odds ratios (ORs) of the disease according to constitution. The medical records of 1443 adults who had been examined and classified based on their constitution at Kyung Hee University Hospital in Seoul, Korea were reviewed. A chi-squared test and Fisher's exact test were used to compare the prevalence of diabetes according to constitution, and multiple logistic regression was used to calculate the ORs for diabetes. The prevalence of diabetes differed significantly according to constitution (χ2 = 36.20, df = 2, P < 0.001). Specifically, the prevalence of the disease was higher in Tae-eumin (11.4%) individuals than in Soyangin (5.0%) or Soeumin (1.7%) individuals. In addition, multiple logistic regression revealed that Tae-eumin individuals had a greater risk for diabetes than Soeumin individuals. When compared to Soeumin individuals, the adjusted ORs were 2.01 (95% CI 0.77–5.26) for Soyangin individuals and 3.96 (95% CI 1.48–10.60) for Tae-eumin individuals. These results show that constitution has a significant and independent association with diabetes, which suggests that constitution is an independent risk factor for diabetes that should be considered when attempting to detect and prevent the disease. PMID:19745018

Use of allele scores as instrumental variables for Mendelian randomization

PubMed Central

Burgess, Stephen; Thompson, Simon G

2013-01-01

Background An allele score is a single variable summarizing multiple genetic variants associated with a risk factor. It is calculated as the total number of risk factor-increasing alleles for an individual (unweighted score), or the sum of weights for each allele corresponding to estimated genetic effect sizes (weighted score). An allele score can be used in a Mendelian randomization analysis to estimate the causal effect of the risk factor on an outcome. Methods Data were simulated to investigate the use of allele scores in Mendelian randomization where conventional instrumental variable techniques using multiple genetic variants demonstrate ‘weak instrument’ bias. The robustness of estimates using the allele score to misspecification (for example non-linearity, effect modification) and to violations of the instrumental variable assumptions was assessed. Results Causal estimates using a correctly specified allele score were unbiased with appropriate coverage levels. The estimates were generally robust to misspecification of the allele score, but not to instrumental variable violations, even if the majority of variants in the allele score were valid instruments. Using a weighted rather than an unweighted allele score increased power, but the increase was small when genetic variants had similar effect sizes. Naive use of the data under analysis to choose which variants to include in an allele score, or for deriving weights, resulted in substantial biases. Conclusions Allele scores enable valid causal estimates with large numbers of genetic variants. The stringency of criteria for genetic variants in Mendelian randomization should be maintained for all variants in an allele score. PMID:24062299

A Risk Score for Predicting Multiple Sclerosis.

PubMed

Dobson, Ruth; Ramagopalan, Sreeram; Topping, Joanne; Smith, Paul; Solanky, Bhavana; Schmierer, Klaus; Chard, Declan; Giovannoni, Gavin

2016-01-01

Multiple sclerosis (MS) develops as a result of environmental influences on the genetically susceptible. Siblings of people with MS have an increased risk of both MS and demonstrating asymptomatic changes in keeping with MS. We set out to develop an MS risk score integrating both genetic and environmental risk factors. We used this score to identify siblings at extremes of MS risk and attempted to validate the score using brain MRI. 78 probands with MS, 121 of their unaffected siblings and 103 healthy controls were studied. Personal history was taken, and serological and genetic analysis using the illumina immunochip was performed. Odds ratios for MS associated with each risk factor were derived from existing literature, and the log values of the odds ratios from each of the risk factors were combined in an additive model to provide an overall score. Scores were initially calculated using log odds ratio from the HLA-DRB1*1501 allele only, secondly using data from all MS-associated SNPs identified in the 2011 GWAS. Subjects with extreme risk scores underwent validation studies. MRI was performed on selected individuals. There was a significant difference in the both risk scores between people with MS, their unaffected siblings and healthy controls (p<0.0005). Unaffected siblings had a risk score intermediate to people with MS and controls (p<0.0005). The best performing risk score generated an AUC of 0.82 (95%CI 0.75-0.88). The risk score demonstrates an AUC on the threshold for clinical utility. Our score enables the identification of a high-risk sibling group to inform pre-symptomatic longitudinal studies.

Investigation of Pseudomonas aeruginosa quorum-sensing signaling system for identifying multiple inhibitors using molecular docking and structural analysis methodology.

PubMed

Soheili, Vahid; Bazzaz, Bibi Sedigheh Fazly; Abdollahpour, Nooshin; Hadizadeh, Farzin

2015-12-01

Pseudomonas aeruginosa is an opportunistic human pathogen and a common Gram-negative bacterium in hospital-acquired infections. It causes death in many burn victims, cystic-fibrosis and neutropenic-cancer patients. It is known that P. aeruginosa biofilm maturation and production of cell-associated and extracellular virulence factors such as pyocyanin, elastase and rhamnolipids are under the control of a quorum-sensing (QS) system. Among several proteins involved in the Pseudomonas QS mechanism, LasR and PqsE play an important role in its cascade signaling system. They can cause increases in QS factors, biofilm maturation, and the production of virulence factors. Therefore, inhibition of these proteins can reduce the pathogenicity of P. aeruginosa. According to the structure of corresponding auto-inducers bound to these proteins, in silico calculations were performed with some non-steroidal anti-inflammatory drugs (NSAIDs) to estimate possible interactions and find the co-inhibitors of LasR and PqsE. The results showed that oxicams (Piroxicam and Meloxicam) can interact well with active sites of both proteins with the Ki of 119.43 nM and 4.0 μM for Meloxicam and 201.39 nM and 4.88 μM against LasR and PqsE, respectively. These findings suggested that Piroxicam and Meloxicam can be used as potential inhibitors for control of the P. aeruginosa QS signaling system and biofilm formation, and may be used in the design of multiple inhibitors. Copyright © 2015 Elsevier Ltd. All rights reserved.

Advanced Spectral Modeling Development

DTIC Science & Technology

1992-09-14

above, the AFGL line-by-line code already possesses many of the attributes desired of a generally applicable transmittance/radiance simulation code, it...transmittance calculations, (b) perform generalized multiple scattering calculations, (c) calculate both heating and dissociative fluxes, (d) provide...This report is subdivided into task specific subsections. The following section describes our general approach to address these technical issues (Section

Non-linear relationship of cell hit and transformation probabilities in a low dose of inhaled radon progenies.

PubMed

Balásházy, Imre; Farkas, Arpád; Madas, Balázs Gergely; Hofmann, Werner

2009-06-01

Cellular hit probabilities of alpha particles emitted by inhaled radon progenies in sensitive bronchial epithelial cell nuclei were simulated at low exposure levels to obtain useful data for the rejection or support of the linear-non-threshold (LNT) hypothesis. In this study, local distributions of deposited inhaled radon progenies in airway bifurcation models were computed at exposure conditions characteristic of homes and uranium mines. Then, maximum local deposition enhancement factors at bronchial airway bifurcations, expressed as the ratio of local to average deposition densities, were determined to characterise the inhomogeneity of deposition and to elucidate their effect on resulting hit probabilities. The results obtained suggest that in the vicinity of the carinal regions of the central airways the probability of multiple hits can be quite high, even at low average doses. Assuming a uniform distribution of activity there are practically no multiple hits and the hit probability as a function of dose exhibits a linear shape in the low dose range. The results are quite the opposite in the case of hot spots revealed by realistic deposition calculations, where practically all cells receive multiple hits and the hit probability as a function of dose is non-linear in the average dose range of 10-100 mGy.

Pharmacokinetics of multiple doses of transdermal flunixin meglumine in adult Holstein dairy cows.

PubMed

Kleinhenz, M D; Gorden, P J; Smith, J S; Schleining, J A; Kleinhenz, K E; Wulf, L L; Sidhu, P K; Rea, D; Coetzee, J F

2018-06-01

A transdermal formulation of the nonsteroidal anti-inflammatory drug, flunixin meglumine, has been approved in the United States and Canada for single-dose administration. Transdermal flunixin meglumine was administered to 10 adult Holstein cows in their second or third lactation at the label dose of 3.33 mg/kg every 24 hr for three total treatments. Plasma flunixin concentrations were determined using high-pressure liquid chromatography with mass spectroscopy (HPLC-MS). Pharmacokinetic analysis was completed on each individual animal with noncompartmental methods using computer software. The time to maximum drug concentration (Tmax) was 2.81 hr, and the maximum drug concentration was 1.08 μg/ml. The mean terminal half-life (T½) was determined to be 5.20 hr. Clearance per fraction absorbed (Cl/F) was calculated to be 0.294 L/hr kg -1 , and volume of distribution of fraction (Vz/F) absorbed was 2.20 L/kg. The mean accumulation factor was 1.10 after three doses. This indicates changes in dosing may not be required when giving multiple doses of flunixin transdermal. Further work is required to investigate the clinical efficacy of transdermal flunixin after multiple daily doses. © 2018 John Wiley & Sons Ltd.

Linearized theory of inhomogeneous multiple 'water-bag' plasmas

NASA Technical Reports Server (NTRS)

Bloomberg, H. W.; Berk, H. L.

1973-01-01

Equations are derived for describing the inhomogeneous equilibrium and small deviations from the equilibrium, giving particular attention to systems with trapped particles. An investigation is conducted of periodic systems with a single trapped-particle water bag, taking into account the behavior of the perturbation equations at the turning points. An outline is provided concerning a procedure for obtaining the eigenvalues. The results of stability calculations connected with the sideband effects are considered along with questions regarding the general applicability of the multiple water-bag approach in stability calculations.

Multiple frequency method for operating electrochemical sensors

DOEpatents

Martin, Louis P [San Ramon, CA

2012-05-15

A multiple frequency method for the operation of a sensor to measure a parameter of interest using calibration information including the steps of exciting the sensor at a first frequency providing a first sensor response, exciting the sensor at a second frequency providing a second sensor response, using the second sensor response at the second frequency and the calibration information to produce a calculated concentration of the interfering parameters, using the first sensor response at the first frequency, the calculated concentration of the interfering parameters, and the calibration information to measure the parameter of interest.

Analysis of clinical risk factors associated with the prognosis of severe multiple-trauma patients with acute lung injury.

PubMed

Wu, Junsong; Sheng, Lei; Wang, Shenhua; Li, Qiang; Zhang, Mao; Xu, Shaowen; Gan, Jianxin

2012-09-01

Several clinical risk factors have been reported to be associated with the prognosis of acute lung injury (ALI). However, these studies have included a general trauma patient population, without singling out the severely injured multiple-trauma patient population. To identify the potential risk factors that could affect the prognosis of ALI in multiple-trauma patients and investigate the prognostic effects of certain risk factors among different patient subpopulations. In this retrospective cohort study, severely injured multiple-trauma patients with early onset of ALI from several trauma centers were studied. Potential risk factors affecting the prognosis of ALI were examined by univariate and multivariate logistic analyses. There were 609 multiple-trauma patients with ALI admitted to the emergency department and emergency intensive care unit during the study period. The nine risk factors that affected prognosis, as indicated by the unadjusted odds ratios with 95% confidence intervals, were the APACHE II (Acute Physiology and Chronic Health Evaluation II) score, duration of trauma, age, gastrointestinal hemorrhage, pulmonary contusion, disseminated intravascular coagulation (DIC), multiple blood transfusions in 6 h, Injury Severity Score (ISS), and aspiration of gastric contents. Specific risk factors also affected different patient subpopulations in different ways. Patients older than 65 years and with multiple (> 10 units) blood transfusions in the early stage after multiple trauma were found to be independent risk factors associated with deterioration of ALI. The other factors studied, including pulmonary contusion, APACHE II score ≥ 20, ISS ≥ 16, gastrointestinal hemorrhage, and aspiration of gastric contents, may predict the unfavorable prognosis of ALI in the early stage of trauma, with their effects attenuating in the later stage. Duration of trauma ≥ 1 h and the presence of DIC may also indicate unfavorable prognosis during the entire treatment period. Crown Copyright © 2012. Published by Elsevier Inc. All rights reserved.

Journal impact factor and methodological quality of surgical randomized controlled trials: an empirical study.

PubMed

Ahmed Ali, Usama; Reiber, Beata M M; Ten Hove, Joren R; van der Sluis, Pieter C; Gooszen, Hein G; Boermeester, Marja A; Besselink, Marc G

2017-11-01

The journal impact factor (IF) is often used as a surrogate marker for methodological quality. The objective of this study is to evaluate the relation between the journal IF and methodological quality of surgical randomized controlled trials (RCTs). Surgical RCTs published in PubMed in 1999 and 2009 were identified. According to IF, RCTs were divided into groups of low (<2), median (2-3) and high IF (>3), as well as into top-10 vs all other journals. Methodological quality characteristics and factors concerning funding, ethical approval and statistical significance of outcomes were extracted and compared between the IF groups. Additionally, a multivariate regression was performed. The median IF was 2.2 (IQR 2.37). The percentage of 'low-risk of bias' RCTs was 13% for top-10 journals vs 4% for other journals in 1999 (P < 0.02), and 30 vs 12% in 2009 (P < 0.02). Similar results were observed for high vs low IF groups. The presence of sample-size calculation, adequate generation of allocation and intention-to-treat analysis were independently associated with publication in higher IF journals; as were multicentre trials and multiple authors. Publication of RCTs in high IF journals is associated with moderate improvement in methodological quality compared to RCTs published in lower IF journals. RCTs with adequate sample-size calculation, generation of allocation or intention-to-treat analysis were associated with publication in a high IF journal. On the other hand, reporting a statistically significant outcome and being industry funded were not independently associated with publication in a higher IF journal.

Geomechanical Model Calibration Using Field Measurements for a Petroleum Reserve

NASA Astrophysics Data System (ADS)

Park, Byoung Yoon; Sobolik, Steven R.; Herrick, Courtney G.

2018-03-01

A finite element numerical analysis model has been constructed that consists of a mesh that effectively captures the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multimechanism deformation (M-D) salt constitutive model using the daily data of actual wellhead pressure and oil-brine interface location. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt are limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used as the field baseline measurement. The structure factor, A 2, and transient strain limit factor, K 0, in the M-D constitutive model are used for the calibration. The value of A 2, obtained experimentally from BC salt, and the value of K 0, obtained from Waste Isolation Pilot Plant salt, are used for the baseline values. To adjust the magnitude of A 2 and K 0, multiplication factors A 2 F and K 0 F are defined, respectively. The A 2 F and K 0 F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict behaviors of the salt dome, caverns, caprock, and interbed layers. The geotechnical concerns associated with the BC site from this analysis will be explained in a follow-up paper.

Exploring Secondary Students' Knowledge and Misconceptions about Influenza: Development, validation, and implementation of a multiple-choice influenza knowledge scale

NASA Astrophysics Data System (ADS)

Romine, William L.; Barrow, Lloyd H.; Folk, William R.

2013-07-01

Understanding infectious diseases such as influenza is an important element of health literacy. We present a fully validated knowledge instrument called the Assessment of Knowledge of Influenza (AKI) and use it to evaluate knowledge of influenza, with a focus on misconceptions, in Midwestern United States high-school students. A two-phase validation process was used. In phase 1, an initial factor structure was calculated based on 205 students of grades 9-12 at a rural school. In phase 2, one- and two-dimensional factor structures were analyzed from the perspectives of classical test theory and the Rasch model using structural equation modeling and principal components analysis (PCA) on Rasch residuals, respectively. Rasch knowledge measures were calculated for 410 students from 6 school districts in the Midwest, and misconceptions were verified through the χ 2 test. Eight items measured knowledge of flu transmission, and seven measured knowledge of flu management. While alpha reliability measures for the subscales were acceptable, Rasch person reliability measures and PCA on residuals advocated for a single-factor scale. Four misconceptions were found, which have not been previously documented in high-school students. The AKI is the first validated influenza knowledge assessment, and can be used by schools and health agencies to provide a quantitative measure of impact of interventions aimed at increasing understanding of influenza. This study also adds significantly to the literature on misconceptions about influenza in high-school students, a necessary step toward strategic development of educational interventions for these students.

Geomechanical Model Calibration Using Field Measurements for a Petroleum Reserve

DOE PAGES

Park, Byoung Yoon; Sobolik, Steven R.; Herrick, Courtney G.

2018-01-19

A finite element numerical analysis model has been constructed that consists of a mesh that effectively captures the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multimechanism deformation (M-D) salt constitutive model using the daily data of actual wellhead pressure and oil–brine interface location. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt are limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used as the field baseline measurement.more » The structure factor, A 2, and transient strain limit factor, K o, in the M-D constitutive model are used for the calibration. The value of A 2, obtained experimentally from BC salt, and the value of K o, obtained from Waste Isolation Pilot Plant salt, are used for the baseline values. To adjust the magnitude of A 2 and K0, multiplication factors A 2 F and K o F are defined, respectively. The A 2 F and K0F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict behaviors of the salt dome, caverns, caprock, and interbed layers. In conclusion, the geotechnical concerns associated with the BC site from this analysis will be explained in a follow-up paper.« less

Geomechanical Model Calibration Using Field Measurements for a Petroleum Reserve

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Byoung Yoon; Sobolik, Steven R.; Herrick, Courtney G.

A finite element numerical analysis model has been constructed that consists of a mesh that effectively captures the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multimechanism deformation (M-D) salt constitutive model using the daily data of actual wellhead pressure and oil–brine interface location. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt are limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used as the field baseline measurement.more » The structure factor, A 2, and transient strain limit factor, K o, in the M-D constitutive model are used for the calibration. The value of A 2, obtained experimentally from BC salt, and the value of K o, obtained from Waste Isolation Pilot Plant salt, are used for the baseline values. To adjust the magnitude of A 2 and K0, multiplication factors A 2 F and K o F are defined, respectively. The A 2 F and K0F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict behaviors of the salt dome, caverns, caprock, and interbed layers. In conclusion, the geotechnical concerns associated with the BC site from this analysis will be explained in a follow-up paper.« less

Geomechanical Simulation of Bayou Choctaw Strategic Petroleum Reserve - Model Calibration.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Park, Byoung

2017-02-01

A finite element numerical analysis model has been constructed that consists of a realistic mesh capturing the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multi - mechanism deformation ( M - D ) salt constitutive model using the daily data of actual wellhead pressure and oil - brine interface. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt is limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN aremore » used for the field baseline measurement. The structure factor, A 2 , and transient strain limit factor, K 0 , in the M - D constitutive model are used for the calibration. The A 2 value obtained experimentally from the BC salt and K 0 value of Waste Isolation Pilot Plant (WIPP) salt are used for the baseline values. T o adjust the magnitude of A 2 and K 0 , multiplication factors A2F and K0F are defined, respectively. The A2F and K0F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back fitting analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict past and future geomechanical behaviors of the salt dome, caverns, caprock , and interbed layers. The geological concerns issued in the BC site will be explained from this model in a follow - up report .« less

Use of an improved radiation amplification factor to estimate the effect of total ozone changes on action spectrum weighted irradiances and an instrument response function

NASA Astrophysics Data System (ADS)

Herman, Jay R.

2010-12-01

Multiple scattering radiative transfer results are used to calculate action spectrum weighted irradiances and fractional irradiance changes in terms of a power law in ozone Ω, U(Ω/200)-RAF, where the new radiation amplification factor (RAF) is just a function of solar zenith angle. Including Rayleigh scattering caused small differences in the estimated 30 year changes in action spectrum-weighted irradiances compared to estimates that neglect multiple scattering. The radiative transfer results are applied to several action spectra and to an instrument response function corresponding to the Solar Light 501 meter. The effect of changing ozone on two plant damage action spectra are shown for plants with high sensitivity to UVB (280-315 nm) and those with lower sensitivity, showing that the probability for plant damage for the latter has increased since 1979, especially at middle to high latitudes in the Southern Hemisphere. Similarly, there has been an increase in rates of erythemal skin damage and pre-vitamin D3 production corresponding to measured ozone decreases. An example conversion function is derived to obtain erythemal irradiances and the UV index from measurements with the Solar Light 501 instrument response function. An analytic expressions is given to convert changes in erythemal irradiances to changes in CIE vitamin-D action spectrum weighted irradiances.

Use of an Improved Radiation Amplification Factor to Estimate the Effect of Total Ozone Changes on Action Spectrum Weighted Irradiances and an Instrument Response Function

NASA Technical Reports Server (NTRS)

Herman, Jay R.

2010-01-01

Multiple scattering radiative transfer results are used to calculate action spectrum weighted irradiances and fractional irradiance changes in terms of a power law in ozone OMEGA, U(OMEGA/200)(sup -RAF), where the new radiation amplification factor (RAF) is just a function of solar zenith angle. Including Rayleigh scattering caused small differences in the estimated 30 year changes in action spectrum-weighted irradiances compared to estimates that neglect multiple scattering. The radiative transfer results are applied to several action spectra and to an instrument response function corresponding to the Solar Light 501 meter. The effect of changing ozone on two plant damage action spectra are shown for plants with high sensitivity to UVB (280-315 run) and those with lower sensitivity, showing that the probability for plant damage for the latter has increased since 1979, especially at middle to high latitudes in the Southern Hemisphere. Similarly, there has been an increase in rates of erythemal skin damage and pre-vitamin D3 production corresponding to measured ozone decreases. An example conversion function is derived to obtain erythemal irradiances and the UV index from measurements with the Solar Light 501 instrument response function. An analytic expressions is given to convert changes in erythemal irradiances to changes in CIE vitamin-D action spectrum weighted irradiances.

The town of Cabar, Croatia, a high risk area for multiple sclerosis--analytic epidemiology of dietary factors.

PubMed

Perković, Olivio; Jurjević, Ante; Rudez, Josip; Antoncić, Igor; Bralić, Marina; Kapović, Miljenko

2010-04-01

Multiple sclerosis (MS) is demyelization disease of central nervous system of unidentified causes. Analytic epidemiological research of 19 patients, clinically approved cases of MS and 25 controls, autochthonic inhabitants of town of Cabar, Croatia, the high-risk zone for the disease, was made. The research plan included case-control investigation--the "door to door" questionnaire--about nutrition habits. An odds ratio (OR) was calculated for all the factors which were more frequently found in the patients than in the controls, and vice versa. The variables that were connected with significant risk for MS in the town of Cabar included: alcohol consumption (p = 0.05), animal fats/dried meat products consumption (p = 0.007), nitrate salting (p = 0.03), strong spices (p = 0.007), mixed bread (p = 0.002), oat and oat products consumption (p = 0.0075). No connection was found with regular consumption of vegetables and fruit (p = 0.009), blue fresh fish (p = 0.028), other fresh fish (p = 0.03), freshwater fish (p = 0.002), canned fish (p = 0.004), dormouse meat (p = 0.007), air-dried meat products (p = 0.004) and using the water from water supply (p = 0.011). In the town of Cabar nutritional customs, primarily food rich in animal fats, alcohol-abuse, and oat consumption could have an influence on MS pathogenesis in genetically inclined individuals.

Cognitive and physical functions related to the level of supervision and dependence in the toileting of stroke patients.

PubMed

Sato, Atsushi; Okuda, Yutaka; Fujita, Takaaki; Kimura, Norihiko; Hoshina, Noriyuki; Kato, Sayaka; Tanaka, Shigenari

2016-01-01

This study aimed to clarify which cognitive and physical factors are associated with the need for toileting assistance in stroke patients and to calculate cut-off values for discriminating between independent supervision and dependent toileting ability. This cross-sectional study included 163 first-stroke patients in nine convalescent rehabilitation wards. Based on their FIM Ⓡ instrument score for toileting, the patients were divided into an independent-supervision group and a dependent group. Multiple logistic regression analysis and receiver operating characteristic analysis were performed to identify factors related to toileting performance. The Minimental State Examination (MMSE); the Stroke Impairment Assessment Set (SIAS) score for the affected lower limb, speech, and visuospatial functions; and the Functional Assessment for Control of Trunk (FACT) were analyzed as independent variables. The multiple logistic regression analysis showed that the FIM Ⓡ instrument score for toileting was associated with the SIAS score for the affected lower limb function, MMSE, and FACT. On receiver operating characteristic analysis, the SIAS score for the affected lower limb function cut-off value was 8/7 points, the MMSE cut-off value was 25/24 points, and the FACT cut-off value was 14/13 points. Affected lower limb function, cognitive function, and trunk function were related with the need for toileting assistance. These cut-off values may be useful for judging whether toileting assistance is needed in stroke patients.

Temporal trend and climate factors of hemorrhagic fever with renal syndrome epidemic in Shenyang City, China

PubMed Central

2011-01-01

Background Hemorrhagic fever with renal syndrome (HFRS) is an important infectious disease caused by different species of hantaviruses. As a rodent-borne disease with a seasonal distribution, external environmental factors including climate factors may play a significant role in its transmission. The city of Shenyang is one of the most seriously endemic areas for HFRS. Here, we characterized the dynamic temporal trend of HFRS, and identified climate-related risk factors and their roles in HFRS transmission in Shenyang, China. Methods The annual and monthly cumulative numbers of HFRS cases from 2004 to 2009 were calculated and plotted to show the annual and seasonal fluctuation in Shenyang. Cross-correlation and autocorrelation analyses were performed to detect the lagged effect of climate factors on HFRS transmission and the autocorrelation of monthly HFRS cases. Principal component analysis was constructed by using climate data from 2004 to 2009 to extract principal components of climate factors to reduce co-linearity. The extracted principal components and autocorrelation terms of monthly HFRS cases were added into a multiple regression model called principal components regression model (PCR) to quantify the relationship between climate factors, autocorrelation terms and transmission of HFRS. The PCR model was compared to a general multiple regression model conducted only with climate factors as independent variables. Results A distinctly declining temporal trend of annual HFRS incidence was identified. HFRS cases were reported every month, and the two peak periods occurred in spring (March to May) and winter (November to January), during which, nearly 75% of the HFRS cases were reported. Three principal components were extracted with a cumulative contribution rate of 86.06%. Component 1 represented MinRH0, MT1, RH1, and MWV1; component 2 represented RH2, MaxT3, and MAP3; and component 3 represented MaxT2, MAP2, and MWV2. The PCR model was composed of three principal components and two autocorrelation terms. The association between HFRS epidemics and climate factors was better explained in the PCR model (F = 446.452, P < 0.001, adjusted R2 = 0.75) than in the general multiple regression model (F = 223.670, P < 0.000, adjusted R2 = 0.51). Conclusion The temporal distribution of HFRS in Shenyang varied in different years with a distinctly declining trend. The monthly trends of HFRS were significantly associated with local temperature, relative humidity, precipitation, air pressure, and wind velocity of the different previous months. The model conducted in this study will make HFRS surveillance simpler and the control of HFRS more targeted in Shenyang. PMID:22133347

OMI Global Tropospheric Bromine Oxide (BrO) Column Densities: Algorithm, Retrieval and Initial Validation

NASA Astrophysics Data System (ADS)

Suleiman, R. M.; Chance, K.; Liu, X.; Kurosu, T. P.; Gonzalez Abad, G.

2014-12-01

We present and discuss a detailed description of the retrieval algorithms for the OMI BrO product. The BrO algorithms are based on direct fitting of radiances from 319.0-347.5 nm. Radiances are modeled from the solar irradiance, attenuated and adjusted by contributions from the target gas and interfering gases, rotational Raman scattering, undersampling, additive and multiplicative closure polynomials and a common mode spectrum. The version of the algorithm used for both BrO includes relevant changes with respect to the operational code, including the fit of the O2-O2 collisional complex, updates in the high resolution solar reference spectrum, updates in spectroscopy, an updated Air Mass Factor (AMF) calculation scheme, and the inclusion of scattering weights and vertical profiles in the level 2 products. Updates to the algorithms include accurate scattering weights and air mass factor calculations, scattering weights and profiles in outputs and available cross sections. We include retrieval parameter and window optimization to reduce the interference from O3, HCHO, O2-O2, SO2, improve fitting accuracy and uncertainty, reduce striping, and improve the long-term stability. We validate OMI BrO with ground-based measurements from Harestua and with chemical transport model simulations. We analyze the global distribution and seasonal variation of BrO and investigate BrO emissions from volcanoes and salt lakes.

Using multi-criteria decision making for selection of the optimal strategy for municipal solid waste management.

PubMed

Jovanovic, Sasa; Savic, Slobodan; Jovicic, Nebojsa; Boskovic, Goran; Djordjevic, Zorica

2016-09-01

Multi-criteria decision making (MCDM) is a relatively new tool for decision makers who deal with numerous and often contradictory factors during their decision making process. This paper presents a procedure to choose the optimal municipal solid waste (MSW) management system for the area of the city of Kragujevac (Republic of Serbia) based on the MCDM method. Two methods of multiple attribute decision making, i.e. SAW (simple additive weighting method) and TOPSIS (technique for order preference by similarity to ideal solution), respectively, were used to compare the proposed waste management strategies (WMS). Each of the created strategies was simulated using the software package IWM2. Total values for eight chosen parameters were calculated for all the strategies. Contribution of each of the six waste treatment options was valorized. The SAW analysis was used to obtain the sum characteristics for all the waste management treatment strategies and they were ranked accordingly. The TOPSIS method was used to calculate the relative closeness factors to the ideal solution for all the alternatives. Then, the proposed strategies were ranked in form of tables and diagrams obtained based on both MCDM methods. As shown in this paper, the results were in good agreement, which additionally confirmed and facilitated the choice of the optimal MSW management strategy. © The Author(s) 2016.

Stochastic Parameterization for Light Absorption by Internally Mixed BC/dust in Snow Grains for Application to Climate Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liou, K. N.; Takano, Y.; He, Cenlin

2014-06-27

A stochastic approach to model the positions of BC/dust internally mixed with two snow-grain types has been developed, including hexagonal plate/column (convex) and Koch snowflake (concave). Subsequently, light absorption and scattering analysis can be followed by means of an improved geometric-optics approach coupled with Monte Carlo photon tracing to determine their single-scattering properties. For a given shape (plate, Koch snowflake, spheroid, or sphere), internal mixing absorbs more light than external mixing. The snow-grain shape effect on absorption is relatively small, but its effect on the asymmetry factor is substantial. Due to a greater probability of intercepting photons, multiple inclusions ofmore » BC/dust exhibit a larger absorption than an equal-volume single inclusion. The spectral absorption (0.2 – 5 um) for snow grains internally mixed with BC/dust is confined to wavelengths shorter than about 1.4 um, beyond which ice absorption predominates. Based on the single-scattering properties determined from stochastic and light absorption parameterizations and using the adding/doubling method for spectral radiative transfer, we find that internal mixing reduces snow albedo more than external mixing and that the snow-grain shape plays a critical role in snow albedo calculations through the asymmetry factor. Also, snow albedo reduces more in the case of multiple inclusion of BC/dust compared to that of an equal-volume single sphere. For application to land/snow models, we propose a two-layer spectral snow parameterization containing contaminated fresh snow on top of old snow for investigating and understanding the climatic impact of multiple BC/dust internal mixing associated with snow grain metamorphism, particularly over mountains/snow topography.« less

Momentum transfer in asteroid impacts. I. Theory and scaling

NASA Astrophysics Data System (ADS)

Holsapple, Keith A.; Housen, Kevin R.

2012-11-01

When an asteroid experiences an impact, its path is changed. How much it changes is important to know for both asteroid evolution studies and for attempts to prevent an asteroid from impacting the Earth. In an impact process the total momentum of the material is conserved. However, not all of the material is of interest, but only that remaining with the asteroid. The ratio of the change of momentum of the remaining asteroid to that of the impactor is called the momentum multiplication factor; and is commonly given the symbol β. It has been known for some time that β can be greater than unity, and in some cases far greater. That could be a significant factor in attempts to deflect an asteroid with an impact, and can also be important in the stirring of objects in the asteroid belt due to mutual impacts. The escaping crater ejecta are the source of the momentum multiplication. Housen and Holsapple (Housen, K.R., Holsapple, K.A. [2011a]. Icarus 211, 856-875) have given a recent summary of ejecta characteristics and scaling. Here we use those ejecta results to determine how β depends on the impactor properties, on the asteroid size and composition, and establish the paths and time of flight of all of the ejecta particles. The approach is to add the contribution of each element of ejected mass accounting for its initial velocity, its trajectory and whether it escapes the asteroid. The goal in this paper is to provide a theoretical framework of the fundamental results which can be used as a test of the veracity of experiments and detailed numerical calculations of impacts. A subsequent paper will present direct laboratory results and numerical simulations of momentum multiplication in various geological materials.

Trends in Mortality After Primary Cytoreductive Surgery for Ovarian Cancer: A Systematic Review and Metaregression of Randomized Clinical Trials and Observational Studies.

PubMed

Di Donato, Violante; Kontopantelis, Evangelos; Aletti, Giovanni; Casorelli, Assunta; Piacenti, Ilaria; Bogani, Giorgio; Lecce, Francesca; Benedetti Panici, Pierluigi

2017-06-01

Primary cytoreductive surgery (PDS) followed by platinum-based chemotherapy is the cornerstone of treatment and the absence of residual tumor after PDS is universally considered the most important prognostic factor. The aim of the present analysis was to evaluate trend and predictors of 30-day mortality in patients undergoing primary cytoreduction for ovarian cancer. Literature was searched for records reporting 30-day mortality after PDS. All cohorts were rated for quality. Simple and multiple Poisson regression models were used to quantify the association between 30-day mortality and the following: overall or severe complications, proportion of patients with stage IV disease, median age, year of publication, and weighted surgical complexity index. Using the multiple regression model, we calculated the risk of perioperative mortality at different levels for statistically significant covariates of interest. Simple regression identified median age and proportion of patients with stage IV disease as statistically significant predictors of 30-day mortality. When included in the multiple Poisson regression model, both remained statistically significant, with an incidence rate ratio of 1.087 for median age and 1.017 for stage IV disease. Disease stage was a strong predictor, with the risk estimated to increase from 2.8% (95% confidence interval 2.02-3.66) for stage III to 16.1% (95% confidence interval 6.18-25.93) for stage IV, for a cohort with a median age of 65 years. Metaregression demonstrated that increased age and advanced clinical stage were independently associated with an increased risk of mortality, and the combined effects of both factors greatly increased the risk.

Molecular structure, vibrational spectra, NBO analysis, first hyperpolarizability, and HOMO-LUMO studies of 2-amino-4-hydroxypyrimidine by density functional method

NASA Astrophysics Data System (ADS)

Jeyavijayan, S.

2015-04-01

This study is a comparative analysis of FTIR and FT-Raman spectra of 2-amino-4-hydroxypyrimidine. The total energies of different conformations have been obtained from DFT (B3LYP) method with 6-31+G(d,p) and 6-311++G(d,p) basis sets. The barrier of planarity between the most stable and planar form is also predicted. The molecular structure, vibrational wavenumbers, infrared intensities, Raman scattering activities were calculated for the molecule using the B3LYP density functional theory (DFT) method. The computed values of frequencies are scaled using multiple scaling factors to yield good coherence with the observed values. Reliable vibrational assignments were made on the basis of total energy distribution (TED) along with scaled quantum mechanical (SQM) method. The stability of the molecule arising from hyperconjugative interactions, charge delocalization has been analyzed using natural bond orbital (NBO) analysis. Non-linear properties such as electric dipole moment (μ), polarizability (α), and hyperpolarizability (β) values of the investigated molecule have been computed using B3LYP quantum chemical calculation. The calculated HOMO and LUMO energies show that charge transfer occurs within the molecule. Besides, molecular electrostatic potential (MEP), Mulliken's charges analysis, and several thermodynamic properties were performed by the DFT method.

TGMI: an efficient algorithm for identifying pathway regulators through evaluation of triple-gene mutual interaction

PubMed Central

Gunasekara, Chathura; Zhang, Kui; Deng, Wenping; Brown, Laura

2018-01-01

Abstract Despite their important roles, the regulators for most metabolic pathways and biological processes remain elusive. Presently, the methods for identifying metabolic pathway and biological process regulators are intensively sought after. We developed a novel algorithm called triple-gene mutual interaction (TGMI) for identifying these regulators using high-throughput gene expression data. It first calculated the regulatory interactions among triple gene blocks (two pathway genes and one transcription factor (TF)), using conditional mutual information, and then identifies significantly interacted triple genes using a newly identified novel mutual interaction measure (MIM), which was substantiated to reflect strengths of regulatory interactions within each triple gene block. The TGMI calculated the MIM for each triple gene block and then examined its statistical significance using bootstrap. Finally, the frequencies of all TFs present in all significantly interacted triple gene blocks were calculated and ranked. We showed that the TFs with higher frequencies were usually genuine pathway regulators upon evaluating multiple pathways in plants, animals and yeast. Comparison of TGMI with several other algorithms demonstrated its higher accuracy. Therefore, TGMI will be a valuable tool that can help biologists to identify regulators of metabolic pathways and biological processes from the exploded high-throughput gene expression data in public repositories. PMID:29579312

[Study of blending method for the extracts of herbal plants].

PubMed

Liu, Yongsuo; Cao, Min; Chen, Yuying; Hu, Yuzhu; Wang, Yiming; Luo, Guoan

2006-03-01

The irregularity in herbal plant composition is influenced by multiple factors. As for quality control of traditional Chinese medicine, the most critical challenge is to ensure the dosage content uniformity. This content uniformity can be improved by blending different batches of the extracts of herbal plants. Nonlinear least-squares regression was used to calculate the blending coefficient, which means no great absolute differences allowed for all ingredients. For traditional Chinese medicines, even relatively smaller differences could present to be very important for all the ingredients. The auto-scaling pretreatment was used prior to the calculation of the blending coefficients. The pretreatment buffered the characteristics of individual data for the ingredients in different batches, so an improved auto-scaling pretreatment method was proposed. With the improved auto-scaling pretreatment, the relative. differences decreased after blending different batches of extracts of herbal plants according to the reference samples. And the content uniformity control of the specific ingredients could be achieved by the error control coefficient. In the studies for the extracts of fructus gardeniae, the relative differences of all the ingredients is less than 3% after blending different batches of the extracts. The results showed that nonlinear least-squares regression can be used to calculate the blending coefficient of the herbal plant extracts.

Parameter optimization of the QUAL2K model for a multiple-reach river using an influence coefficient algorithm.

PubMed

Cho, Jae Heon; Ha, Sung Ryong

2010-03-15

An influence coefficient algorithm and a genetic algorithm (GA) were introduced to develop an automatic calibration model for QUAL2K, the latest version of the QUAL2E river and stream water-quality model. The influence coefficient algorithm was used for the parameter optimization in unsteady state, open channel flow. The GA, used in solving the optimization problem, is very simple and comprehensible yet still applicable to any complicated mathematical problem, where it can find the global-optimum solution quickly and effectively. The previously established model QUAL2Kw was used for the automatic calibration of the QUAL2K. The parameter-optimization method using the influence coefficient and genetic algorithm (POMIG) developed in this study and QUAL2Kw were each applied to the Gangneung Namdaecheon River, which has multiple reaches, and the results of the two models were compared. In the modeling, the river reach was divided into two parts based on considerations of the water quality and hydraulic characteristics. The calibration results by POMIG showed a good correspondence between the calculated and observed values for most of water-quality variables. In the application of POMIG and QUAL2Kw, relatively large errors were generated between the observed and predicted values in the case of the dissolved oxygen (DO) and chlorophyll-a (Chl-a) in the lowest part of the river; therefore, two weighting factors (1 and 5) were applied for DO and Chl-a in the lower river. The sums of the errors for DO and Chl-a with a weighting factor of 5 were slightly lower compared with the application of a factor of 1. However, with a weighting factor of 5 the sums of errors for other water-quality variables were slightly increased in comparison to the case with a factor of 1. Generally, the results of the POMIG were slightly better than those of the QUAL2Kw.

Spread-spectrum multiple access using wideband noncoherent MFSK

NASA Technical Reports Server (NTRS)

Ha, Tri T.; Pratt, Timothy; Maggenti, Mark A.

1987-01-01

Two spread-spectrum multiple access systems which use wideband M-ary frequency shift keying (FSK) (MFSK) as the primary modulation are presented. A bit error rate performance analysis is presented and system throughput is calculated for sample C band and Ku band satellite systems. Sample link analyses are included to illustrate power and adjacent satellite interference considerations in practical multiple access systems.

Nonconvergence of the Wang-Landau algorithms with multiple random walkers.

PubMed

Belardinelli, R E; Pereyra, V D

2016-05-01

This paper discusses some convergence properties in the entropic sampling Monte Carlo methods with multiple random walkers, particularly in the Wang-Landau (WL) and 1/t algorithms. The classical algorithms are modified by the use of m-independent random walkers in the energy landscape to calculate the density of states (DOS). The Ising model is used to show the convergence properties in the calculation of the DOS, as well as the critical temperature, while the calculation of the number π by multiple dimensional integration is used in the continuum approximation. In each case, the error is obtained separately for each walker at a fixed time, t; then, the average over m walkers is performed. It is observed that the error goes as 1/sqrt[m]. However, if the number of walkers increases above a certain critical value m>m_{x}, the error reaches a constant value (i.e., it saturates). This occurs for both algorithms; however, it is shown that for a given system, the 1/t algorithm is more efficient and accurate than the similar version of the WL algorithm. It follows that it makes no sense to increase the number of walkers above a critical value m_{x}, since it does not reduce the error in the calculation. Therefore, the number of walkers does not guarantee convergence.

Steady Boundary Layer Disturbances Created By Two-Dimensional Surface Ripples

NASA Astrophysics Data System (ADS)

Kuester, Matthew

2017-11-01

Multiple experiments have shown that surface roughness can enhance the growth of Tollmien-Schlichting (T-S) waves in a laminar boundary layer. One of the common observations from these studies is a ``wall displacement'' effect, where the boundary layer profile shape remains relatively unchanged, but the origin of the profile pushes away from the wall. The objective of this work is to calculate the steady velocity field (including this wall displacement) of a laminar boundary layer over a surface with small, 2D surface ripples. The velocity field is a combination of a Blasius boundary layer and multiple disturbance modes, calculated using the linearized Navier-Stokes equations. The method of multiple scales is used to include non-parallel boundary layer effects of O (Rδ- 1) ; the non-parallel terms are necessary, because a wall displacement is mathematically inconsistent with a parallel boundary layer assumption. This technique is used to calculate the steady velocity field over ripples of varying height and wavelength, including cases where a separation bubble forms on the leeward side of the ripple. In future work, the steady velocity field will be the input for stability calculations, which will quantify the growth of T-S waves over rough surfaces. The author would like to acknowledge the support of the Kevin T. Crofton Aerospace & Ocean Engineering Department at Virginia Tech.

Research reactor loading pattern optimization using estimation of distribution algorithms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jiang, S.; Ziver, K.; AMCG Group, RM Consultants, Abingdon

2006-07-01

A new evolutionary search based approach for solving the nuclear reactor loading pattern optimization problems is presented based on the Estimation of Distribution Algorithms. The optimization technique developed is then applied to the maximization of the effective multiplication factor (K{sub eff}) of the Imperial College CONSORT research reactor (the last remaining civilian research reactor in the United Kingdom). A new elitism-guided searching strategy has been developed and applied to improve the local convergence together with some problem-dependent information based on the 'stand-alone K{sub eff} with fuel coupling calculations. A comparison study between the EDAs and a Genetic Algorithm with Heuristicmore » Tie Breaking Crossover operator has shown that the new algorithm is efficient and robust. (authors)« less

An Open, Large-Scale, Collaborative Effort to Estimate the Reproducibility of Psychological Science.

PubMed

2012-11-01

Reproducibility is a defining feature of science. However, because of strong incentives for innovation and weak incentives for confirmation, direct replication is rarely practiced or published. The Reproducibility Project is an open, large-scale, collaborative effort to systematically examine the rate and predictors of reproducibility in psychological science. So far, 72 volunteer researchers from 41 institutions have organized to openly and transparently replicate studies published in three prominent psychological journals in 2008. Multiple methods will be used to evaluate the findings, calculate an empirical rate of replication, and investigate factors that predict reproducibility. Whatever the result, a better understanding of reproducibility will ultimately improve confidence in scientific methodology and findings. © The Author(s) 2012.

Computer-generated holograms by multiple wavefront recording plane method with occlusion culling.

PubMed

Symeonidou, Athanasia; Blinder, David; Munteanu, Adrian; Schelkens, Peter

2015-08-24

We propose a novel fast method for full parallax computer-generated holograms with occlusion processing, suitable for volumetric data such as point clouds. A novel light wave propagation strategy relying on the sequential use of the wavefront recording plane method is proposed, which employs look-up tables in order to reduce the computational complexity in the calculation of the fields. Also, a novel technique for occlusion culling with little additional computation cost is introduced. Additionally, the method adheres a Gaussian distribution to the individual points in order to improve visual quality. Performance tests show that for a full-parallax high-definition CGH a speedup factor of more than 2,500 compared to the ray-tracing method can be achieved without hardware acceleration.

Low socioeconomic status is a risk factor for preeclampsia: the Generation R Study.

PubMed

Silva, Lindsay M; Coolman, Marianne; Steegers, Eric Ap; Jaddoe, Vincent Wv; Moll, Henriëtte A; Hofman, Albert; Mackenbach, Johan P; Raat, Hein

2008-06-01

To examine whether maternal socioeconomic status, as indicated by maternal educational level, is associated with preeclampsia, and if so, to what extent known risk factors for preeclampsia mediate the effect of educational level. In the Generation R Study, a population-based cohort study, we examined data of 3547 pregnant women. Odds ratios of preeclampsia for low, mid-low and mid-high educational level compared with high educational level were calculated after adjustment for confounders and additional adjustment for a selection of potential mediators (family history, material factors, psychosocial factors, substance use, working conditions, preexisting medical conditions, maternal anthropometrics and blood pressure at enrollment) that individually caused more than 10% change in the odds ratio for low education. Adjusted for the confounding effects of age, gravidity and multiple pregnancy, women with low educational level were more likely to develop preeclampsia (odds ratio 5.12; 95% confidence interval: 2.20, 11.93) than women with high educational level. After additional adjustment for financial difficulties, smoking in pregnancy, working conditions, body mass index and blood pressure at enrollment, the odds ratio was 4.91 (95% confidence interval: 1.93, 12.52). Low maternal socioeconomic status is a strong risk factor for preeclampsia. Only a small part of this association can be explained by the mediating effects of established risk factors for preeclampsia. Further research is needed to disentangle the pathway from low socioeconomic status to preeclampsia.

[Risk factors associated to diffuse gastric cancer and intestinal histological patterns in an adult population from Western Mexico].

PubMed

Delgado-Figueroa, Netzahualpilli; Casas-Junco, Paloma; Torres-Jasso, Juan Heriberto; Bustos-Carpinteyro, Andrea Rebeca; Santiago-Luna, Ernesto; Marín-Contreras, María Eugenia; Sánchez-López, Josefina Yoaly

Gastric cancer (GC) is the third leading cause of cancer death worldwide, and is divided histologically in diffuse gastric cancer (DGC) and intestinal gastric cancer (IGC). Multiple risk factors have been associated with GC in different populations. The objective was to analyze the risk factors associated to DGC and IGC in a population from the western region of Mexico. The DGC (n = 27) and IGC (n = 26) cases, each matched by age and sex with a control group, were analyzed. Diet and lifestyle data were obtained by a questionnaire. Statistical analysis was performed with the software SPSSv18. The association of risk was calculated in odds ratio (OR); a value of p < 0.05 was considered significant. In the DGC group, the factors with significant OR values were: consumption of pork OR: 3.4 (1.11-10.4; p =0.032), smoking OR: 4.7 (1.5-15.0; p =0.007), green vegetables OR: 0.16 (0.03-0.83; p =0.029) and fruit OR: 0.28 (0.08-0.88; p =0.029). In the IGC group, the consumption of canned sardines was a significant risk factor OR: 4.07 (1.25-13.24; p =0.019). This work is the first to analyze the risk factors associated with GC in a population from western Mexico.

Factors related to falls among community dwelling elderly.

PubMed

Kuhirunyaratn, Piyathida; Prasomrak, Prasert; Jindawong, Bangonsri

2013-09-01

Falls among the elderly can lead to disability, hospitalization and premature death. This study aimed to determine the factors related to falls among community dwelling elderly. This case-control study was conducted at the Samlium Primary Care Unit (SPCU), Khon Kaen, Thailand. Cases were elderly individuals who had fallen within the previous six months and controls were elderly who had not fallen during that same time period. Subjects were taken from elderly persons registered at the SPCU. The sample size was calculated to be 111 cases and 222 controls. Face to face interviews were conducted with subjects between May and June, 2011. The response rate was 100%. On bivariate analysis, the statistically significant factors related to falls were: regular medication use, co-morbidities, mobility, depression, cluttered rooms, slippery floors, unsupported toilets (without a hand rail), sufficient exercise, rapid posture change and wearing slippers. When controlling for others significant factors, multiple logistic regression revealed significant factors were: regular medication use (AOR: 2.22; 95%CI: 1.19 - 4.12), depression (AOR: 1.76, 95% CI: 1.03 - 2.99), sufficient exercise (AOR: 0.34; 95% CI: 0.19 - 0.58) and wearing slippery shoes (AOR: 2.31; 95% CI: 1.24 - 4.29). Interventions need to be considered to modify these significant factors associated with falls and education should be provided to these at risk.

Analysis of Intrinsic Peptide Detectability via Integrated Label-Free and SRM-Based Absolute Quantitative Proteomics.

PubMed

Jarnuczak, Andrew F; Lee, Dave C H; Lawless, Craig; Holman, Stephen W; Eyers, Claire E; Hubbard, Simon J

2016-09-02

Quantitative mass spectrometry-based proteomics of complex biological samples remains challenging in part due to the variability and charge competition arising during electrospray ionization (ESI) of peptides and the subsequent transfer and detection of ions. These issues preclude direct quantification from signal intensity alone in the absence of a standard. A deeper understanding of the governing principles of peptide ionization and exploitation of the inherent ionization and detection parameters of individual peptides is thus of great value. Here, using the yeast proteome as a model system, we establish the concept of peptide F-factor as a measure of detectability, closely related to ionization efficiency. F-factor is calculated by normalizing peptide precursor ion intensity by absolute abundance of the parent protein. We investigated F-factor characteristics in different shotgun proteomics experiments, including across multiple ESI-based LC-MS platforms. We show that F-factors mirror previously observed physicochemical predictors as peptide detectability but demonstrate a nonlinear relationship between hydrophobicity and peptide detectability. Similarly, we use F-factors to show how peptide ion coelution adversely affects detectability and ionization. We suggest that F-factors have great utility for understanding peptide detectability and gas-phase ion chemistry in complex peptide mixtures, selection of surrogate peptides in targeted MS studies, and for calibration of peptide ion signal in label-free workflows. Data are available via ProteomeXchange with identifier PXD003472.

Teaching Mathematics: Computers in the Classroom.

ERIC Educational Resources Information Center

Borba, Marcelo C.

1995-01-01

Discusses some major changes that computers, calculators, and graphing calculators have brought to the mathematics classroom, including quasi-empirical studies in the classroom, use of multiple representations, emphasis on visualization, emphasis on tables, an altered classroom "ecology," and increasing complexity for students. (SR)

Multiple-energy Techniques in Industrial Computerized Tomography

DOE R&D Accomplishments Database

Schneberk, D.; Martz, H.; Azevedo, S.

1990-08-01

Considerable effort is being applied to develop multiple-energy industrial CT techniques for materials characterization. Multiple-energy CT can provide reliable estimates of effective Z (Z{sub eff}), weight fraction, and rigorous calculations of absolute density, all at the spatial resolution of the scanner. Currently, a wide variety of techniques exist for CT scanners, but each has certain problems and limitations. Ultimately, the best multi-energy CT technique would combine the qualities of accuracy, reliability, and wide range of application, and would require the smallest number of additional measurements. We have developed techniques for calculating material properties of industrial objects that differ somewhat from currently used methods. In this paper, we present our methods for calculating Z{sub eff}, weight fraction, and density. We begin with the simplest case -- methods for multiple-energy CT using isotopic sources -- and proceed to multiple-energy work with x-ray machine sources. The methods discussed here are illustrated on CT scans of PBX-9502 high explosives, a lexan-aluminum phantom, and a cylinder of glass beads used in a preliminary study to determine if CT can resolve three phases: air, water, and a high-Z oil. In the CT project at LLNL, we have constructed several CT scanners of varying scanning geometries using {gamma}- and x-ray sources. In our research, we employed two of these scanners: pencil-beam CAT for CT data using isotopic sources and video-CAT equipped with an IRT micro-focal x-ray machine source.

COME: a robust coding potential calculation tool for lncRNA identification and characterization based on multiple features.

PubMed

Hu, Long; Xu, Zhiyu; Hu, Boqin; Lu, Zhi John

2017-01-09

Recent genomic studies suggest that novel long non-coding RNAs (lncRNAs) are specifically expressed and far outnumber annotated lncRNA sequences. To identify and characterize novel lncRNAs in RNA sequencing data from new samples, we have developed COME, a coding potential calculation tool based on multiple features. It integrates multiple sequence-derived and experiment-based features using a decompose-compose method, which makes it more accurate and robust than other well-known tools. We also showed that COME was able to substantially improve the consistency of predication results from other coding potential calculators. Moreover, COME annotates and characterizes each predicted lncRNA transcript with multiple lines of supporting evidence, which are not provided by other tools. Remarkably, we found that one subgroup of lncRNAs classified by such supporting features (i.e. conserved local RNA secondary structure) was highly enriched in a well-validated database (lncRNAdb). We further found that the conserved structural domains on lncRNAs had better chance than other RNA regions to interact with RNA binding proteins, based on the recent eCLIP-seq data in human, indicating their potential regulatory roles. Overall, we present COME as an accurate, robust and multiple-feature supported method for the identification and characterization of novel lncRNAs. The software implementation is available at https://github.com/lulab/COME. © The Author(s) 2016. Published by Oxford University Press on behalf of Nucleic Acids Research.

Numerical modeling of fluid and electrical currents through geometries based on synchrotron X-ray tomographic images of reservoir rocks using Avizo and COMSOL

NASA Astrophysics Data System (ADS)

Bird, M. B.; Butler, S. L.; Hawkes, C. D.; Kotzer, T.

2014-12-01

The use of numerical simulations to model physical processes occurring within subvolumes of rock samples that have been characterized using advanced 3D imaging techniques is becoming increasingly common. Not only do these simulations allow for the determination of macroscopic properties like hydraulic permeability and electrical formation factor, but they also allow the user to visualize processes taking place at the pore scale and they allow for multiple different processes to be simulated on the same geometry. Most efforts to date have used specialized research software for the purpose of simulations. In this contribution, we outline the steps taken to use commercial software Avizo to transform a 3D synchrotron X-ray-derived tomographic image of a rock core sample to an STL (STereoLithography) file which can be imported into the commercial multiphysics modeling package COMSOL. We demonstrate that the use of COMSOL to perform fluid and electrical current flow simulations through the pore spaces. The permeability and electrical formation factor of the sample are calculated and compared with laboratory-derived values and benchmark calculations. Although the simulation domains that we were able to model on a desk top computer were significantly smaller than representative elementary volumes, and we were able to establish Kozeny-Carman and Archie's Law trends on which laboratory measurements and previous benchmark solutions fall. The rock core samples include a Fountainebleau sandstone used for benchmarking and a marly dolostone sampled from a well in the Weyburn oil field of southeastern Saskatchewan, Canada. Such carbonates are known to have complicated pore structures compared with sandstones, yet we are able to calculate reasonable macroscopic properties. We discuss the computing resources required.

Revisiting Molecular Dynamics on a CPU/GPU system: Water Kernel and SHAKE Parallelization.

PubMed

Ruymgaart, A Peter; Elber, Ron

2012-11-13

We report Graphics Processing Unit (GPU) and Open-MP parallel implementations of water-specific force calculations and of bond constraints for use in Molecular Dynamics simulations. We focus on a typical laboratory computing-environment in which a CPU with a few cores is attached to a GPU. We discuss in detail the design of the code and we illustrate performance comparable to highly optimized codes such as GROMACS. Beside speed our code shows excellent energy conservation. Utilization of water-specific lists allows the efficient calculations of non-bonded interactions that include water molecules and results in a speed-up factor of more than 40 on the GPU compared to code optimized on a single CPU core for systems larger than 20,000 atoms. This is up four-fold from a factor of 10 reported in our initial GPU implementation that did not include a water-specific code. Another optimization is the implementation of constrained dynamics entirely on the GPU. The routine, which enforces constraints of all bonds, runs in parallel on multiple Open-MP cores or entirely on the GPU. It is based on Conjugate Gradient solution of the Lagrange multipliers (CG SHAKE). The GPU implementation is partially in double precision and requires no communication with the CPU during the execution of the SHAKE algorithm. The (parallel) implementation of SHAKE allows an increase of the time step to 2.0fs while maintaining excellent energy conservation. Interestingly, CG SHAKE is faster than the usual bond relaxation algorithm even on a single core if high accuracy is expected. The significant speedup of the optimized components transfers the computational bottleneck of the MD calculation to the reciprocal part of Particle Mesh Ewald (PME).

Kinetics of the hydrogen atom abstraction reactions from 1-butanol by hydroxyl radical: theory matches experiment and more.

PubMed

Seal, Prasenjit; Oyedepo, Gbenga; Truhlar, Donald G

2013-01-17

In the present work, we study the H atom abstraction reactions by hydroxyl radical at all five sites of 1-butanol. Multistructural variational transition state theory (MS-VTST) was employed to estimate the five thermal rate constants. MS-VTST utilizes a multifaceted dividing surface that accounts for the multiple conformational structures of the transition state, and we also include all the structures of the reactant molecule. The vibrational frequencies and minimum energy paths (MEPs) were computed using the M08-HX/MG3S electronic structure method. The required potential energy surfaces were obtained implicitly by direct dynamics employing interpolated variational transition state theory with mapping (IVTST-M) using a variational reaction path algorithm. The M08-HX/MG3S electronic model chemistry was then used to calculate multistructural torsional anharmonicity factors to complete the MS-VTST rate constant calculations. The results indicate that torsional anharmonicity is very important at higher temperatures, and neglecting it would lead to errors of 26 and 32 at 1000 and 1500 K, respectively. Our results for the sums of the site-specific rate constants agree very well with the experimental values of Hanson and co-workers at 896-1269 K and with the experimental results of Campbell et al. at 292 K, but slightly less well with the experiments of Wallington et al., Nelson et al., and Yujing and Mellouki at 253-372 K; nevertheless, the calculated rates are within a factor of 1.61 of all experimental values at all temperatures. This gives us confidence in the site-specific values, which are currently inaccessible to experiment.

Hybrid network modeling and the effect of image resolution on digitally-obtained petrophysical and two-phase flow properties

NASA Astrophysics Data System (ADS)

Aghaei, A.

2017-12-01

Digital imaging and modeling of rocks and subsequent simulation of physical phenomena in digitally-constructed rock models are becoming an integral part of core analysis workflows. One of the inherent limitations of image-based analysis, at any given scale, is image resolution. This limitation becomes more evident when the rock has multiple scales of porosity such as in carbonates and tight sandstones. Multi-scale imaging and constructions of hybrid models that encompass images acquired at multiple scales and resolutions are proposed as a solution to this problem. In this study, we investigate the effect of image resolution and unresolved porosity on petrophysical and two-phase flow properties calculated based on images. A helical X-ray micro-CT scanner with a high cone-angle is used to acquire digital rock images that are free of geometric distortion. To remove subjectivity from the analyses, a semi-automated image processing technique is used to process and segment the acquired data into multiple phases. Direct and pore network based models are used to simulate physical phenomena and obtain absolute permeability, formation factor and two-phase flow properties such as relative permeability and capillary pressure. The effect of image resolution on each property is investigated. Finally a hybrid network model incorporating images at multiple resolutions is built and used for simulations. The results from the hybrid model are compared against results from the model built at the highest resolution and those from laboratory tests.

A genotype probability index for multiple alleles and haplotypes.

PubMed

Percy, A; Kinghorn, B P

2005-12-01

We use linear algebra to calculate an index of information content in genotype probabilities which has previously been calculated using trigonometry. The new method can be generalized allowing the index to be calculated for loci with more than two alleles. Applications of this index include its use in genotyping strategies, strategies to manage genetic disorders and in estimation of genotype effects.

Incorporation of multiple cloud layers for ultraviolet radiation modeling studies

NASA Technical Reports Server (NTRS)

Charache, Darryl H.; Abreu, Vincent J.; Kuhn, William R.; Skinner, Wilbert R.

1994-01-01

Cloud data sets compiled from surface observations were used to develop an algorithm for incorporating multiple cloud layers into a multiple-scattering radiative transfer model. Aerosol extinction and ozone data sets were also incorporated to estimate the seasonally averaged ultraviolet (UV) flux reaching the surface of the Earth in the Detroit, Michigan, region for the years 1979-1991, corresponding to Total Ozone Mapping Spectrometer (TOMS) version 6 ozone observations. The calculated UV spectrum was convolved with an erythema action spectrum to estimate the effective biological exposure for erythema. Calculations show that decreasing the total column density of ozone by 1% leads to an increase in erythemal exposure by approximately 1.1-1.3%, in good agreement with previous studies. A comparison of the UV radiation budget at the surface between a single cloud layer method and a multiple cloud layer method presented here is discussed, along with limitations of each technique. With improved parameterization of cloud properties, and as knowledge of biological effects of UV exposure increase, inclusion of multiple cloud layers may be important in accurately determining the biologically effective UV budget at the surface of the Earth.

Designing the X-Ray Microcalorimeter Spectrometer for Optimal Science Return

NASA Technical Reports Server (NTRS)

Ptak, Andrew; Bandler, Simon R.; Bookbinder, Jay; Kelley, Richard L.; Petre, Robert; Smith, Randall K.; Smith, Stephen

2013-01-01

Recent advances in X-ray microcalorimeters enable a wide range of possible focal plane designs for the X-ray Microcalorimeter Spectrometer (XMS) instrument on the future Advanced X-ray Spectroscopic Imaging Observatory (AXSIO) or X-ray Astrophysics Probe (XAP). Small pixel designs (75 microns) oversample a 5-10" PSF by a factor of 3-6 for a 10 m focal length, enabling observations at both high count rates and high energy resolution. Pixel designs utilizing multiple absorbers attached to single transition-edge sensors can extend the focal plane to cover a significantly larger field of view, albeit at a cost in maximum count rate and energy resolution. Optimizing the science return for a given cost and/or complexity is therefore a non-trivial calculation that includes consideration of issues such as the mission science drivers, likely targets, mirror size, and observing efficiency. We present a range of possible designs taking these factors into account and their impacts on the science return of future large effective-area X-ray spectroscopic missions.

[Prevalence of leisure-time physical activity and associated factors: a population-based study in São Paulo, Brazil, 2008-2009].

PubMed

Sousa, Clóvis Arlindo de; César, Chester Luiz Galvão; Barros, Marilisa Berti de Azevedo; Carandina, Luana; Goldbaum, Moisés; Marchioni, Dirce Maria Lobo; Fisberg, Regina Mara

2013-02-01

The purpose of this study was to ascertain the prevalence of self-reported leisure-time physical activity and related factors in the city of São Paulo, Brazil, 2008-2009. A population- based cross-sectional study interviewed 2,691 individuals of both sexes, 12 years or older. A two-stage cluster (census tract, household) random sample provided data using home interviews in 2008 and 2009. Leisure-time physical activity was measured with IPAQ, long version. Complex sample-adjusted descriptive statistics provided prevalence estimates, chi-square tests screened associations, and prevalence ratios (PR) expressed effects. Multiple Poisson regression was used to ascertain adjusted effects, and design effects were calculated. Of the interviewees, 16.4% (95%CI: 14.3-18.7) reported leisure-time physical activity. The findings indicate the importance of encouraging leisure-time physical activity, which was associated with male sex, higher income, younger age (12 to 29 years), not smoking, and not reporting frequent fatigue.

Value of information of repair times for offshore wind farm maintenance planning

NASA Astrophysics Data System (ADS)

Seyr, Helene; Muskulus, Michael

2016-09-01

A large contribution to the total cost of energy in offshore wind farms is due to maintenance costs. In recent years research has focused therefore on lowering the maintenance costs using different approaches. Decision support models for scheduling the maintenance exist already, dealing with different factors influencing the scheduling. Our contribution deals with the uncertainty in the repair times. Given the mean repair times for different turbine components we make some assumptions regarding the underlying repair time distribution. We compare the results of a decision support model for the mean times to repair and those repair time distributions. Additionally, distributions with the same mean but different variances are compared under the same conditions. The value of lowering the uncertainty in the repair time is calculated and we find that using distributions significantly decreases the availability, when scheduling maintenance for multiple turbines in a wind park. Having detailed information about the repair time distribution may influence the results of maintenance modeling and might help identify cost factors.

Linear regression analysis: part 14 of a series on evaluation of scientific publications.

PubMed

Schneider, Astrid; Hommel, Gerhard; Blettner, Maria

2010-11-01

Regression analysis is an important statistical method for the analysis of medical data. It enables the identification and characterization of relationships among multiple factors. It also enables the identification of prognostically relevant risk factors and the calculation of risk scores for individual prognostication. This article is based on selected textbooks of statistics, a selective review of the literature, and our own experience. After a brief introduction of the uni- and multivariable regression models, illustrative examples are given to explain what the important considerations are before a regression analysis is performed, and how the results should be interpreted. The reader should then be able to judge whether the method has been used correctly and interpret the results appropriately. The performance and interpretation of linear regression analysis are subject to a variety of pitfalls, which are discussed here in detail. The reader is made aware of common errors of interpretation through practical examples. Both the opportunities for applying linear regression analysis and its limitations are presented.

Measurement of company effectiveness using analytic network process method

NASA Astrophysics Data System (ADS)

Goran, Janjić; Zorana, Tanasić; Borut, Kosec

2017-07-01

The sustainable development of an organisation is monitored through the organisation's performance, which beforehand incorporates all stakeholders' requirements in its strategy. The strategic management concept enables organisations to monitor and evaluate their effectiveness along with efficiency by monitoring of the implementation of set strategic goals. In the process of monitoring and measuring effectiveness, an organisation can use multiple-criteria decision-making methods as help. This study uses the method of analytic network process (ANP) to define the weight factors of the mutual influences of all the important elements of an organisation's strategy. The calculation of an organisation's effectiveness is based on the weight factors and the degree of fulfilment of the goal values of the strategic map measures. New business conditions influence the changes in the importance of certain elements of an organisation's business in relation to competitive advantage on the market, and on the market, increasing emphasis is given to non-material resources in the process of selection of the organisation's most important measures.

International employment in clinical practice: influencing factors for the dental hygienist.

PubMed

Abbott, A; Barrow, S-Y; Lopresti, F; Hittelman, E

2005-02-01

To assess demographics, job characteristics, geographical regions, resources and commitment, which influence dental hygienists seeking international clinical practice employment opportunities. Questionnaires were mailed to a convenience sample of members of the Dental Hygienists' Association of the City of New York. Statistical analyses were conducted and frequency distributions and relationships between variables were calculated. Seventy-two percent of respondents reported that they are or may be interested in working overseas. Italy and Spain (67%) were the regions of most interest. Salary (65%) was cited as the most influencing factor in selection, whereas non-compliance with the equivalency to Occupational Safety and Health Administration standards (74%) was the most frequently perceived barrier. Multiple language fluency was statistically significant (0.003) regarding interest in overseas employment. Policy makers, employers and educators need to be aware of these findings should recruitment be a possibility to render urgently needed oral hygiene care in regions where there is a perceived shortage of dental hygienists.

A prediction method of ice breaking resistance using a multiple regression analysis

NASA Astrophysics Data System (ADS)

Cho, Seong-Rak; Lee, Sungsu

2015-07-01

The two most important tasks of icebreakers are first to secure a sailing route by breaking the thick sea ice and second to sail efficiently herself for purposes of exploration and transportation in the polar seas. The resistance of icebreakers is a priority factor at the preliminary design stage; not only must their sailing efficiency be satisfied, but the design of the propulsion system will be directly affected. Therefore, the performance of icebreakers must be accurately calculated and evaluated through the use of model tests in an ice tank before construction starts. In this paper, a new procedure is developed, based on model tests, to estimate a ship's ice breaking resistance during continuous ice-breaking in ice. Some of the factors associated with crushing failures are systematically considered in order to correctly estimate her ice-breaking resistance. This study is intended to contribute to the improvement of the techniques for ice resistance prediction with ice breaking ships.

Calculation Method of Lateral Strengths and Ductility Factors of Constructions with Shear Walls of Different Ductility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yamaguchi, Nobuyoshi; Nakao, Masato; Murakami, Masahide

2008-07-08

For seismic design, ductility-related force modification factors are named R factor in Uniform Building Code of U.S, q factor in Euro Code 8 and Ds (inverse of R) factor in Japanese Building Code. These ductility-related force modification factors for each type of shear elements are appeared in those codes. Some constructions use various types of shear walls that have different ductility, especially for their retrofit or re-strengthening. In these cases, engineers puzzle the decision of force modification factors of the constructions. Solving this problem, new method to calculate lateral strengths of stories for simple shear wall systems is proposed andmore » named 'Stiffness--Potential Energy Addition Method' in this paper. This method uses two design lateral strengths for each type of shear walls in damage limit state and safety limit state. Two lateral strengths of stories in both limit states are calculated from these two design lateral strengths for each type of shear walls in both limit states. Calculated strengths have the same quality as values obtained by strength addition method using many steps of load-deformation data of shear walls. The new method to calculate ductility factors is also proposed in this paper. This method is based on the new method to calculate lateral strengths of stories. This method can solve the problem to obtain ductility factors of stories with shear walls of different ductility.« less

Assessment of Risk Factors of Intrauterine Adhesions in Patients With Induced Abortion and the Curative Effect of Hysteroscopic Surgery.

PubMed

Mo, Xiaoliang; Qin, Guirong; Zhou, Zhoulin; Jiang, Xiaoli

2017-10-03

To explore the risk factors for intrauterine adhesions in patients with artificial abortion and clinical efficacy of hysteroscopic dissection. 1500 patients undergoing artificial abortion between January 2014 and June 2015 were enrolled into this study. The patients were divided into two groups with or without intrauterine adhesions. Univariate and Multiple logistic regression were conducted to assess the effects of multiple factors on the development of intrauterine adhesions following induced abortion. The incidence rate for intrauterine adhesions following induced abortion is 17.0%. Univariate showed that preoperative inflammation, multiple pregnancies and suction evacuation time are the influence risk factors of intrauterine adhesions. Multiple logistic regression demonstrates that multiple pregnancies, high intrauterine negative pressure, and long suction evacuation time are independent risk factors for the development of intrauterine adhesions following induced abortion. Additionally, intrauterine adhesions were observed in 105 mild, 80 moderate, and 70 severe cases. The cure rates for these three categories of intrauterine adhesions by hysteroscopic surgery were 100.0%, 93.8%, and 85.7%, respectively. Multiple pregnancies, high negative pressure suction evacuation and long suction evacuation time are independent risk factors for the development of intrauterine adhesions following induced abortions. Hysteroscopic surgery substantially improves the clinical outcomes of intrauterine adhesions.

Temperature effects on the fractionation of multiple sulfur isotopes by Thermodesulfobacterium and Desulfovibrio strains

NASA Astrophysics Data System (ADS)

Wang, P.; Sun, C.; Ono, S.; Lin, L.

2012-12-01

Microbial dissimilatory sulfate reduction is one of the major mechanisms driving anaerobic mineralization of organic matter in global ocean. While sulfate-reducing prokaryotes are well known to fractionate sulfur isotopes during dissimilatory sulfate reduction, unraveling the isotopic compositions of sulfur-bearing minerals preserved in sedimentary records could provide invaluable constraints on the evolution of seawater chemistry and metabolic pathways. Variations in the sulfur isotope fractionations are partly due to inherent differences among species and also affected by environmental conditions. The isotope fractionations caused by microbial sulfate reduction have been interpreted to be a sequence of enzyme-catalyzed isotope fractionation steps. Therefore, the fractionation factor depends on (1) the sulfate flux into and out of the cell, and (2) the flux of sulfur transformation between the internal pools. Whether the multiple sulfur isotope effect could be quantitatively predicted using such a metabolic flux model would provide insights into the cellular machinery catalyzing with sulfate reduction. This study examined the multiple sulfur isotope fractionation patterns associated with a thermophilic Thermodesulfobacterium-related strain and a mesophilic Desulfovibrio gigas over a wide temperature range. The Thermodesulfobacterium-related strain grew between 34 and 79°C with an optimal temperature at 72°C and the highest cell-specific sulfate reduction rate at 77°C. The 34ɛ values ranged between 8.2 and 31.6‰ with a maximum at 68°C. The D. gigas grew between 10 and 45 °C with an optimal temperature at 30°C and the highest cell-specific sulfate reduction rate at 41°C. The 34ɛ values ranged between 10.3 and 29.7‰ with higher magnitude at both lower and higher temperatures. The results of multiple sulfur isotope measurements expand the previously reported range and cannot be described by a solution field of the metabolic flux model, which calculates the Δ33S and 34ɛ values assuming equilibrium fractionation among internal steps. Either larger isotope effects or kinetic fractionation has to be considered in the metabolic flux model to explain the multiple sulfur isotope effect produced by these two strains. Overall, the metabolic flux model warrants further revision and further studies regarding physiological responses to growth conditions may probably offer a linkage between multiple sulfur isotope effects and environmental factors for microbial dissimilatory sulfate reduction.

Holographic 3D multi-spot two-photon excitation for fast optical stimulation in brain

NASA Astrophysics Data System (ADS)

Takiguchi, Yu; Toyoda, Haruyoshi

2017-04-01

We report here a holographic high speed accessing microscope of sensory-driven synaptic activity across all inputs to single living neurons in the context of the intact cerebral cortex. This system is based on holographic multiple beam generation with spatial light modulator, we have demonstrated performance of the holographic excitation efficiency in several in vitro prototype system. 3D weighted iterative Fourier Transform method using the Ewald sphere in consideration of calculation speed has been adopted; multiple locations can be patterned in 3D with single hologram. Standard deviation of intensities of spots are still large due to the aberration of the system and/or hologram calculation, we successfully excited multiple locations of neurons in living mouse brain to monitor the calcium signals.

Mercury and neuromotor function among children in a rural town in Chile

PubMed Central

Huber, Stella Maria; Schomaker, Michael; Heumann, Christian; Schierl, Rudolf; Michalke, Bernhard; Jenni, Oskar G.; Caflisch, Jon; Muñoz, Daniel Moraga; von Ehrenstein, Ondine S.; Radon, Katja

2016-01-01

Background Mercury (Hg) exposure from artisanal gold mining has adverse effects on the neuromotor function in adults. However, few studies have examined this relationship in children. Objectives To investigate the impact of Hg exposure on children’s neuromotor function. Methods Cross-sectional data on Hg risk factors and demographics were collected from n = 288 children (response = 68.9%). Based on complete cases (CCs) (n = 130) and multiple imputations (n = 288), associations between fingernail Hg and four different neuromotor function components were calculated using multiple logistic regression adjusted for confounders. Results Of the children, 11.1, 14.9, 63.9, and 10.4% had pathologic pure motor skills, adaptive fine motor skills, adaptive gross motor skills, and static balance, respectively. No significant association between fingernail Hg and any neuromotor component was found. However, Hg burning in the household was significantly associated with children’s pathologic pure motor skills (OR 3.07 95% CI 1.03–9.18). Conclusion Elemental Hg exposure in the household might have adverse long-term effects on children’s pure motor skills. PMID:27078174

Central hemodynamics and arterial stiffness in idiopathic and multiple system atrophy.

PubMed

Franzen, Klaas; Fliegen, Sabine; Koester, Jelena; Martin, Rafael Campos; Deuschl, Günther; Reppel, Michael; Mortensen, Kai; Schneider, Susanne A

2017-02-01

Blood pressure is commonly abnormal in parkinsonian disorders, but central hemodynamics and arterial stiffness, well-established predictors of total cardiovascular risk, have rarely been studied in these disorders. 32 patients [27 with idiopathic Parkinson's disease (iPD); 5 with multiple system atrophy (MSA)] and 15 controls matched for cardiac risk factors underwent 24 h-ambulatory blood pressure recordings using an I.E.M. device (Mobil-O-Graph™), measuring peripheral pressure and calculating central pressures and arterial stiffness. Mean augmentation indices corrected for heart rate (AIx@75) were significantly lower and pulse wave velocities were significantly elevated in patients compared to controls. Central systolic blood pressure, cardiac output and daytime total vascular resistance were significantly elevated in patients. Mean nocturnal systolic peripheral blood pressure and nocturnal heart rates were also significantly higher; 56.3% of patients had nocturnal hypertension (80% of the MSA group); 85.2% showed non-dipping. This supports previous findings of reduced vulnerability to systemic atherosclerosis and end-organ damage in treated PD. Yet, hemodynamic abnormalities were common and often remained asymptomatic.

Three-dimensional Monte Carlo calculation of some nuclear parameters

NASA Astrophysics Data System (ADS)

Günay, Mehtap; Şeker, Gökmen

2017-09-01

In this study, a fusion-fission hybrid reactor system was designed by using 9Cr2WVTa Ferritic steel structural material and the molten salt-heavy metal mixtures 99-95% Li20Sn80 + 1-5% RG-Pu, 99-95% Li20Sn80 + 1-5% RG-PuF4, and 99-95% Li20Sn80 + 1-5% RG-PuO2, as fluids. The fluids were used in the liquid first wall, blanket and shield zones of a fusion-fission hybrid reactor system. Beryllium (Be) zone with the width of 3 cm was used for the neutron multiplication between the liquid first wall and blanket. This study analyzes the nuclear parameters such as tritium breeding ratio (TBR), energy multiplication factor (M), heat deposition rate, fission reaction rate in liquid first wall, blanket and shield zones and investigates effects of reactor grade Pu content in the designed system on these nuclear parameters. Three-dimensional analyses were performed by using the Monte Carlo code MCNPX-2.7.0 and nuclear data library ENDF/B-VII.0.

Epidemiology of multiple sclerosis in Qom: Demographic study in Iran.

PubMed

Rezaali, Saeed; Khalilnezhad, Ahad; Naser Moghadasi, Abdorreza; Chaibakhsh, Samira; Sahraian, Mohammad Ali

2013-01-01

Recent studies have demonstrated controversial results and somewhat increased frequency of multiple sclerosis (MS). We reevaluated the files of MS patients from Qom Province of Iran in order to investigate the epidemiology of the disease. Demographic and clinical records of 592 MS patients were reviewed, which included; age, sex, date of birth, marital and occupation status, presenting symptoms, time of onset, type and family history of MS, and history of autoimmune or other diseases. At the time of our study, 11 patients had died, and 581 were alive with a total female-to-male ratio of 3.4. The mean age of onset of the disease was 34.25 ± 9.01 for all the patients. 11.2% of patients had positive family history of MS. The majority of patients (80.1%) showed relapsing-remitting (RR) pattern. The prevalence of MS was calculated as 50.4/100000 for Qom. Qom is located within a high risk zone of MS. Although we found evidences about the role of environmental factors, geographical distribution, and etcetera, many more studies need to be performed in this respect.

Mechanisms for Differential Protein Production in Toxin–Antitoxin Systems

PubMed Central

Deter, Heather S.; Jensen, Roderick V.; Mather, William H.; Butzin, Nicholas C.

2017-01-01

Toxin–antitoxin (TA) systems are key regulators of bacterial persistence, a multidrug-tolerant state found in bacterial species that is a major contributing factor to the growing human health crisis of antibiotic resistance. Type II TA systems consist of two proteins, a toxin and an antitoxin; the toxin is neutralized when they form a complex. The ratio of antitoxin to toxin is significantly greater than 1.0 in the susceptible population (non-persister state), but this ratio is expected to become smaller during persistence. Analysis of multiple datasets (RNA-seq, ribosome profiling) and results from translation initiation rate calculators reveal multiple mechanisms that ensure a high antitoxin-to-toxin ratio in the non-persister state. The regulation mechanisms include both translational and transcriptional regulation. We classified E. coli type II TA systems into four distinct classes based on the mechanism of differential protein production between toxin and antitoxin. We find that the most common regulation mechanism is translational regulation. This classification scheme further refines our understanding of one of the fundamental mechanisms underlying bacterial persistence, especially regarding maintenance of the antitoxin-to-toxin ratio. PMID:28677629

Evaluation of the telegrapher's equation and multiple-flux theories for calculating the transmittance and reflectance of a diffuse absorbing slab.

PubMed

Kong, Steven H; Shore, Joel D

2007-03-01

We study the propagation of light through a medium containing isotropic scattering and absorption centers. With a Monte Carlo simulation serving as the benchmark solution to the radiative transfer problem of light propagating through a turbid slab, we compare the transmission and reflection density computed from the telegrapher's equation, the diffusion equation, and multiple-flux theories such as the Kubelka-Munk and four-flux theories. Results are presented for both normally incident light and diffusely incident light. We find that we can always obtain very good results from the telegrapher's equation provided that two parameters that appear in the solution are set appropriately. We also find an interesting connection between certain solutions of the telegrapher's equation and solutions of the Kubelka-Munk and four-flux theories with a small modification to how the phenomenological parameters in those theories are traditionally related to the optical scattering and absorption coefficients of the slab. Finally, we briefly explore how well the theories can be extended to the case of anisotropic scattering by multiplying the scattering coefficient by a simple correction factor.

A Multiple Indicators Multiple Cause (MIMIC) model of respiratory health and household factors in Chinese children: the seven Northeastern cities (SNEC) study.

PubMed

Dong, Guang-Hui; Qian, Zhengmin; Fu, Qiang; Wang, Jing; Trevathan, Edwin; Ma, Wenjun; Liu, Miao-Miao; Wang, Da; Ren, Wan-Hui; Ong, Kee-Hean; Ferguson, Tekeda Freeman; Riley, Erin; Simckes, Maayan

2014-01-01

In China, with the rapid economic development and improvement of living standards over the past few decades, the household living environment has shifted dramatically. The aim of the present study is to assess the impact of home environment factors on respiratory symptoms and asthma in Chinese children. Investigators analyzed data collected in the 25 districts from the seven Northeastern cities to examine health effects on respiratory symptoms and asthma in 31,049 children aged 2-14 years. Factor analysis was used to reduce 33 children's lifestyle and household variables to six new 'factor' variables. The multiple indicators multiple causes approach was used to examine the relationship between indoor air pollution and respiratory health status, controlling for covariates. Factor analyses generated six factor variables of potential household risk factors from an original list of 33 variables. The respiratory symptoms and asthma were significantly associated with the recent home renovation factor (estimate = 0.076, p < 0.001), pet ownership factor (estimate = 0.095, p < 0.001), environmental tobacco smoke (ETS) exposure factor (estimate = 0.181, p < 0.001) and PVC-flooring factor (estimate = 0.031, p = 0.007). Home ventilation factor was not related to any respiratory condition (estimate = 0.028, p = 0.074). Independent respiratory health effects existed for multiple household environmental factors recent home renovation, pet ownership, ETS, and PVC-flooring.

Common risk factors for chronic non-communicable diseases among older adults in China, Ghana, Mexico, India, Russia and South Africa: the study on global AGEing and adult health (SAGE) wave 1.

PubMed

Wu, Fan; Guo, Yanfei; Chatterji, Somnath; Zheng, Yang; Naidoo, Nirmala; Jiang, Yong; Biritwum, Richard; Yawson, Alfred; Minicuci, Nadia; Salinas-Rodriguez, Aaron; Manrique-Espinoza, Betty; Maximova, Tamara; Peltzer, Karl; Phaswanamafuya, Nancy; Snodgrass, James J; Thiele, Elizabeth; Ng, Nawi; Kowal, Paul

2015-02-06

Behavioral risk factors such as tobacco use, unhealthy diet, insufficient physical activity and the harmful use of alcohol are known and modifiable contributors to a number of NCDs and health mediators. The purpose of this paper is to describe the distribution of main risk factors for NCDs by socioeconomic status (SES) among adults aged 50 years and older within a country and compare these risk factors across six lower- and upper-middle income countries. The study population in this paper draw from SAGE Wave 1 and consisted of adults aged 50-plus from China (N=13,157), Ghana (N=4,305), India (N=6,560), Mexico (N=2,318), the Russian Federation (N=3,938) and South Africa (N=3,836). Seven main common risk factors for NCDs were identified: daily tobacco use, frequent heavy drinking, low level physical activity, insufficient vegetable and fruit intake, high risk waist-hip ratio, obesity and hypertension. Multiple risk factors were also calculated by summing all these risk factors. The prevalence of daily tobacco use ranged from 7.7% (Ghana) to 46.9% (India), frequent heavy drinker was the highest in China (6.3%) and lowest in India (0.2%), and the highest prevalence of low physical activity was in South Africa (59.7%). The highest prevalence of respondents with high waist-to-hip ratio risk was 84.5% in Mexico, and the prevalence of self-reported hypertension ranging from 33% (India) to 78% (South Africa). Obesity was more common in South Africa, the Russia Federation and Mexico (45.2%, 36% and 28.6%, respectively) compared with China, India and Ghana (15.3%, 9.7% and 6.4%, respectively). China, Ghana and India had a higher prevalence of respondents with multiple risk factors than Mexico, the Russia Federation and South Africa. The occurrence of three and four risk factors was more prevalent in Mexico, the Russia Federation and South Africa. There were substantial variations across countries and settings, even between upper-middle income countries and lower-middle income countries. The baseline information on the magnitude of the problem of risk factors provided by this study can help countries and health policymakers to set up interventions addressing the global non-communicable disease epidemic.

Self-interaction correction in multiple scattering theory: application to transition metal oxides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Daene, Markus W; Lueders, Martin; Ernst, Arthur

2009-01-01

We apply to transition metal monoxides the self-interaction corrected (SIC) local spin density (LSD) approximation, implemented locally in the multiple scattering theory within the Korringa-Kohn-Rostoker (KKR) band structure method. The calculated electronic structure and in particular magnetic moments and energy gaps are discussed in reference to the earlier SIC results obtained within the LMTO-ASA band structure method, involving transformations between Bloch and Wannier representations to solve the eigenvalue problem and calculate the SIC charge and potential. Since the KKR can be easily extended to treat disordered alloys, by invoking the coherent potential approximation (CPA), in this paper we compare themore » CPA approach and supercell calculations to study the electronic structure of NiO with cation vacancies.« less

A general formalism for phase space calculations

NASA Technical Reports Server (NTRS)

Norbury, John W.; Deutchman, Philip A.; Townsend, Lawrence W.; Cucinotta, Francis A.

1988-01-01

General formulas for calculating the interactions of galactic cosmic rays with target nuclei are presented. Methods for calculating the appropriate normalization volume elements and phase space factors are presented. Particular emphasis is placed on obtaining correct phase space factors for 2-, and 3-body final states. Calculations for both Lorentz-invariant and noninvariant phase space are presented.

Multidisciplinary design optimization of aircraft wing structures with aeroelastic and aeroservoelastic constraints

NASA Astrophysics Data System (ADS)

Jung, Sang-Young

Design procedures for aircraft wing structures with control surfaces are presented using multidisciplinary design optimization. Several disciplines such as stress analysis, structural vibration, aerodynamics, and controls are considered simultaneously and combined for design optimization. Vibration data and aerodynamic data including those in the transonic regime are calculated by existing codes. Flutter analyses are performed using those data. A flutter suppression method is studied using control laws in the closed-loop flutter equation. For the design optimization, optimization techniques such as approximation, design variable linking, temporary constraint deletion, and optimality criteria are used. Sensitivity derivatives of stresses and displacements for static loads, natural frequency, flutter characteristics, and control characteristics with respect to design variables are calculated for an approximate optimization. The objective function is the structural weight. The design variables are the section properties of the structural elements and the control gain factors. Existing multidisciplinary optimization codes (ASTROS* and MSC/NASTRAN) are used to perform single and multiple constraint optimizations of fully built up finite element wing structures. Three benchmark wing models are developed and/or modified for this purpose. The models are tested extensively.

An FPGA computing demo core for space charge simulation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Jinyuan; Huang, Yifei; /Fermilab

2009-01-01

In accelerator physics, space charge simulation requires large amount of computing power. In a particle system, each calculation requires time/resource consuming operations such as multiplications, divisions, and square roots. Because of the flexibility of field programmable gate arrays (FPGAs), we implemented this task with efficient use of the available computing resources and completely eliminated non-calculating operations that are indispensable in regular micro-processors (e.g. instruction fetch, instruction decoding, etc.). We designed and tested a 16-bit demo core for computing Coulomb's force in an Altera Cyclone II FPGA device. To save resources, the inverse square-root cube operation in our design is computedmore » using a memory look-up table addressed with nine to ten most significant non-zero bits. At 200 MHz internal clock, our demo core reaches a throughput of 200 M pairs/s/core, faster than a typical 2 GHz micro-processor by about a factor of 10. Temperature and power consumption of FPGAs were also lower than those of micro-processors. Fast and convenient, FPGAs can serve as alternatives to time-consuming micro-processors for space charge simulation.« less

Variation in the cost of care for primary total knee arthroplasties.

PubMed

Haas, Derek A; Kaplan, Robert S

2017-03-01

The study examined the cost variation across 29 high-volume US hospitals and their affiliated orthopaedic surgeons for delivering a primary total knee arthroplasty without major complicating conditions. The hospitals had similar patient demographics, and more than 80% of them had statistically-similar Medicare risk-adjusted readmission and complication rates. Hospital and physician personnel costs were calculated using time-driven activity-based costing. Consumable supply costs, such as the prosthetic implant, were calculated using purchase prices, and postacute care costs were measured using either internal costs or external claims as reported by each hospital. Despite having similar patient demographics and readmission and complication rates, the average cost of care for total knee arthroplasty across the hospitals varied by a factor of about 2 to 1. Even after adjusting for differences in internal labor cost rates, the hospital at the 90th percentile of cost spent about twice as much as the one at the 10th percentile of cost. The large variation in costs among sites suggests major and multiple opportunities to transfer knowledge about process and productivity improvements that lower costs while simultaneously maintaining or improving outcomes.

Characterization of synthesis and storage of TGF-alpha in rat parotid acinar and intercalated duct cells.

PubMed

Login, G R; Yang, J; Bryan, K P; Digenis, E C; McBride, J; Elovic, A; Quissell, D O; Dvorak, A M; Wong, D T

1997-03-01

Although the expression and biological role of transforming growth factor-alpha (TGF-alpha) have been explored in a variety of normal cells in mammalian species, little is known about the storage of TGF-alpha in secretory cells of exocrine organs. Parotid glands from four rats were homogenized for RNA isolation followed by reverse transcription-polymerase chain reaction to determine the presence of TGF-alpha message. In situ hybridization using a hamster-specific TGF-alpha riboprobe was done on paraffin sections. Parotid gland and isolated acinar cells were processed for transmission electron microscopy (TEM) and postembedding immunogold labeled for TGF-alpha. Gold particles were counted on approximately 200 granules in 10 acinar cells and in 10 intercalated duct cells. Labeling density was calculated as the number of gold particles per square micrometer +/- SD. Statistical significance was calculated using one-way analysis of variance. Using multiple technologies, we have established that rat parotid acinar and intercalated duct cells synthesize TGF-alpha and store the precursor form of this cytokine in their secretory granules.

S/sub n/ analysis of the TRX metal lattices with ENDF/B version III data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wheeler, F.J.; Pearlstein, S.

1975-03-01

Two critical assemblies, designated as thermal-reactor benchmarks TRX-1 and TRX-2 for ENDF/B data testing, were analyzed using the one-dimensional S/sub n/-theory code SCAMP. The two assemblies were simple lattices of aluminum-clad, uranium-metal fuel rods in triangular arrays with D$sub 2$O as moderator and reflector. The fuel was low-enriched (1.3 percent $sup 235$U), 0.387-inch in diameter and had an active height of 48 inches. The volume ratio of water to uranium was 2.35 for the TRX-1 lattice and 4.02 for TRX-2. Full-core S/sub n/ calculations based on Version III data were performed for these assemblies and the results obtained were comparedmore » with the measured values of the multiplication factors, the ratio of epithermal-to-thermal neutron capture in $sup 238$U, the ratio of epithermal-to-thermal fission in $sup 235$U, the ratio of $sup 238$U fission to $sup 235$U fission, and the ratio of capture in $sup 238$U to fission in $sup 235$U. Reaction rates were obtained from a central region of the full- core problems. Multigroup cross sections for the reactor calculation were obtained from S/sub n/ cell calculations with resonance self-shielding calculated using the RABBLE treatment. The results of the analyses are generally consistent with results obtained by other investigators. (auth)« less

STANDARD BIG BANG NUCLEOSYNTHESIS UP TO CNO WITH AN IMPROVED EXTENDED NUCLEAR NETWORK

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coc, Alain; Goriely, Stephane; Xu, Yi

Primordial or big bang nucleosynthesis (BBN) is one of the three strong pieces of evidence for the big bang model together with the expansion of the universe and cosmic microwave background radiation. In this study, we improve the standard BBN calculations taking into account new nuclear physics analyses and enlarge the nuclear network up to sodium. This is, in particular, important to evaluate the primitive value of CNO mass fraction that could affect Population III stellar evolution. For the first time we list the complete network of more than 400 reactions with references to the origin of the rates, includingmore » Almost-Equal-To 270 reaction rates calculated using the TALYS code. Together with the cosmological light elements, we calculate the primordial beryllium, boron, carbon, nitrogen, and oxygen nuclei. We performed a sensitivity study to identify the important reactions for CNO, {sup 9}Be, and boron nucleosynthesis. We re-evaluated those important reaction rates using experimental data and/or theoretical evaluations. The results are compared with precedent calculations: a primordial beryllium abundance increase by a factor of four compared to its previous evaluation, but we note a stability for B/H and for the CNO/H abundance ratio that remains close to its previous value of 0.7 Multiplication-Sign 10{sup -15}. On the other hand, the extension of the nuclear network has not changed the {sup 7}Li value, so its abundance is still 3-4 times greater than its observed spectroscopic value.« less

A general model for preload calculation and stiffness analysis for combined angular contact ball bearings

NASA Astrophysics Data System (ADS)

Zhang, Jinhua; Fang, Bin; Hong, Jun; Wan, Shaoke; Zhu, Yongsheng

2017-12-01

The combined angular contact ball bearings are widely used in automatic, aerospace and machine tools, but few researches on the combined angular contact ball bearings have been reported. It is shown that the preload and stiffness of combined bearings are mutual influenced rather than simply the superposition of multiple single bearing, therefore the characteristic calculation of combined bearings achieved by coupling the load and deformation analysis of a single bearing. In this paper, based on the Jones quasi-static model and stiffness analytical model, a new iterative algorithm and model are proposed for the calculation of combined bearings preload and stiffness, and the dynamic effects include centrifugal force and gyroscopic moment have to be considered. It is demonstrated that the new method has general applicability, the preload factors of combined bearings are calculated according to the different design preloads, and the static and dynamic stiffness for various arrangements of combined bearings are comparatively studied and analyzed, and the influences of the design preload magnitude, axial load and rotating speed are discussed in detail. Besides, the change rule of dynamic contact angles of combined bearings with respect to the rotating speed is also discussed. The results show that bearing arrangement modes, rotating speed and design preload magnitude have a significant influence on the preload and stiffness of combined bearings. The proposed formulation provides a useful tool in dynamic analysis of the complex bearing-rotor system.

Calculation and Specification of the Multiple Chirality Displayed by Sugar Pyranoid Ring Structures.

ERIC Educational Resources Information Center

Shallenberger, Robert S.; And Others

1981-01-01

Describes a method, using simple algebraic notation, for calculating the nature of the salient features of a sugar pyranoid ring, the steric disposition of substituents about the reference, and the anomeric carbon atoms contained within the ring. (CS)

Community factors to promote parents' quality of child-nurturing life.

PubMed

Aoyama, Megumi; Wei, Chang Nian; Chang-nian, Wei; Harada, Koichi; Ueda, Kimiyo; Takano, Miyuki; Ueda, Atsushi

2013-01-01

The purpose of this study was to clarify the role of community factors in parents' quality of child-nurturing life (QCNL). We developed a questionnaire to evaluate the degree of QCNL and determine the structural factors related to QCNL as community factors related to parents' QCNL derived from focus group interviews and the Delphi technique. The questionnaire also included the battery of the self-rating depression scale and Tsumori-Inage Infant's Developmental Test. Using the questionnaire, we then conducted a quantitative survey of parents whose children attended nursery schools in Kumamoto Prefecture. Factor analysis, calculation of the mean score and/or ratio to each item, Pearson's correlation coefficient, t test, multiple regression analysis, and covariance structure analysis were performed. The questionnaire we developed consisted of seven items with 75 elements, involving ten elements as community factors. Subjects included 699 parents (mean age 33.6 ± 5.4 years) and 965 children (age range 0-6 years). Factor analysis revealed that community factors consisted of five factors, such as "lifestyle rooted in the ground," "balance of housekeeping and work," "community network," "amenity," and "regeneration of life". These factors may be dominant in a rural area. Finally, we developed a structural model with "community factors," QCNL, QOL, and "child growth" by covariance structural analysis. The analysis revealed that community factors had a positive relation to parents' QCNL (r = 0.81, p < 0.001) and that parental SDS score had a negative relation to parents' QCNL (r = -0.59, p < 0.001). The analysis did show that community factors were positively related to the sound growth of children. The covariance structure analysis revealed that community factors were associated with parents' QCNL, SDS, and "child growth."

A /31,15/ Reed-Solomon Code for large memory systems

NASA Technical Reports Server (NTRS)

Lim, R. S.

1979-01-01

This paper describes the encoding and the decoding of a (31,15) Reed-Solomon Code for multiple-burst error correction for large memory systems. The decoding procedure consists of four steps: (1) syndrome calculation, (2) error-location polynomial calculation, (3) error-location numbers calculation, and (4) error values calculation. The principal features of the design are the use of a hardware shift register for both high-speed encoding and syndrome calculation, and the use of a commercially available (31,15) decoder for decoding Steps 2, 3 and 4.

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2010 CFR

2010-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2011 CFR

2011-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2012 CFR

2012-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2014 CFR

2014-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

46 CFR 42.15-25 - Hatchways closed by portable covers and secured weathertight by tarpaulins and battening devices.

Code of Federal Regulations, 2013 CFR

2013-10-01

... maximum stress thus calculated and the factor 4.25 shall not exceed the minimum ultimate strength of the... foot on hatchways in position 2 and the product of the maximum stress thus calculated and the factor 5... product of the maximum stress thus calculated and the factor 5 shall not exceed the minimum ultimate...

Magma addition rates in continental arcs: New methods of calculation and global implications

NASA Astrophysics Data System (ADS)

Ratschbacher, B. C.; Paterson, S. R.

2017-12-01

The transport of mass, heat and geochemical constituents (elements and volatiles) from the mantle to the atmosphere occurs via magma addition to the lithosphere. Calculation of magma addition rates (MARs) in continental arcs based on exposed proportions of igneous arc rocks is complex and rarely consistently determined. Multiple factors influence MAR calculations such as crust versus mantle contributions to magmas, a change in MARs across the arc and with depths throughout the arc crustal column, `arc tempos' with periods of high and low magmatic activity, the loss of previous emplaced arc rocks by subsequent magmatism and return to the mantle, arc migration, variations in the intrusive versus extrusive additions and evolving arc widths and thicknesses during tectonism. All of these factors need to be considered when calculating MARs.This study makes a new attempt to calculate MARs in continental arcs by studying three arc sections: the Famatinian arc, Argentina, the Sierra Nevada batholith, California and the Coast Mountain batholith, Washington and British Columbia. Arcs are divided into fore-arc, main arc and back arc sections and `boxes' with a defined width, length and thickness spanning upper middle and lower crustal levels are assigned to each section. Representative exposed crustal slices for each depth are then used to calculate MARs based on outcrop proportions for each box. Geochemical data is used to infer crustal recycling percentages and total thickness of the arc. Preliminary results show a correlation between MARs, crustal thicknesses and magmatic flare-up durations. For instance, the Famatinian arc shows a strong decrease in MARs between the main arc section (9.4 km3/Ma/arc-km) and the fore-arc (0.61 km3/Ma/arc-km) and back-arc (1.52 km3/Ma/arc-km) regions and an increase in the amount of magmatism with depth.Global MARs over geologic timescales have the potential to investigate mantle melt generation rates and the volatile outgassing contribution of unerupted arc magmas to the balance of volatile element cycling from the mantle to the surface. We address this question by using exposed arc length estimates from 760 Ma until present (Cao et al. 2017, EPSL) and scale to MARs based on constrains from the detailed study of the three arc sections and a further division into magma-rich and magma-poor arcs.

The Golden Ratio: A Golden Opportunity to Investigate Multiple Representations of a Problem.

ERIC Educational Resources Information Center

Dickey, Edwin M.

1993-01-01

This article explores the multiple representations (verbal, algebraic, graphical, and numerical) that can be used to study the golden ratio. Emphasis is placed on using technology (both calculators and computers) to investigate the algebraic, graphical, and numerical representations. (JAF)

The scalar and electromagnetic form factors of the nucleon in dispersively improved Chiral EFT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alarcon, Jose Manuel

We present a method for calculating the nucleon form factors of G-parity-even operators. This method combines chiral effective field theory (χEFT) and dispersion theory. Through unitarity we factorize the imaginary part of the form factors into a perturbative part, calculable with χEFT, and a non-perturbative part, obtained through other methods. We consider the scalar and electromagnetic (EM) form factors of the nucleon. The results show an important improvement compared to standard chiral calculations, and can be used in analysis of the low-energy properties of the nucleon.

Double-multiple streamtube model for Darrieus in turbines

NASA Technical Reports Server (NTRS)

Paraschivoiu, I.

1981-01-01

An analytical model is proposed for calculating the rotor performance and aerodynamic blade forces for Darrieus wind turbines with curved blades. The method of analysis uses a multiple-streamtube model, divided into two parts: one modeling the upstream half-cycle of the rotor and the other, the downstream half-cycle. The upwind and downwind components of the induced velocities at each level of the rotor were obtained using the principle of two actuator disks in tandem. Variation of the induced velocities in the two parts of the rotor produces larger forces in the upstream zone and smaller forces in the downstream zone. Comparisons of the overall rotor performance with previous methods and field test data show the important improvement obtained with the present model. The calculations were made using the computer code CARDAA developed at IREQ. The double-multiple streamtube model presented has two major advantages: it requires a much shorter computer time than the three-dimensional vortex model and is more accurate than multiple-streamtube model in predicting the aerodynamic blade loads.

DNA melting profiles from a matrix method.

PubMed

Poland, Douglas

2004-02-05

In this article we give a new method for the calculation of DNA melting profiles. Based on the matrix formulation of the DNA partition function, the method relies for its efficiency on the fact that the required matrices are very sparse, essentially reducing matrix multiplication to vector multiplication and thus making the computer time required to treat a DNA molecule containing N base pairs proportional to N(2). A key ingredient in the method is the result that multiplication by the inverse matrix can also be reduced to vector multiplication. The task of calculating the melting profile for the entire genome is further reduced by treating regions of the molecule between helix-plateaus, thus breaking the molecule up into independent parts that can each be treated individually. The method is easily modified to incorporate changes in the assignment of statistical weights to the different structural features of DNA. We illustrate the method using the genome of Haemophilus influenzae. Copyright 2003 Wiley Periodicals, Inc.

A case study of view-factor rectification procedures for diffuse-gray radiation enclosure computations

NASA Technical Reports Server (NTRS)

Taylor, Robert P.; Luck, Rogelio

1995-01-01

The view factors which are used in diffuse-gray radiation enclosure calculations are often computed by approximate numerical integrations. These approximately calculated view factors will usually not satisfy the important physical constraints of reciprocity and closure. In this paper several view-factor rectification algorithms are reviewed and a rectification algorithm based on a least-squares numerical filtering scheme is proposed with both weighted and unweighted classes. A Monte-Carlo investigation is undertaken to study the propagation of view-factor and surface-area uncertainties into the heat transfer results of the diffuse-gray enclosure calculations. It is found that the weighted least-squares algorithm is vastly superior to the other rectification schemes for the reduction of the heat-flux sensitivities to view-factor uncertainties. In a sample problem, which has proven to be very sensitive to uncertainties in view factor, the heat transfer calculations with weighted least-squares rectified view factors are very good with an original view-factor matrix computed to only one-digit accuracy. All of the algorithms had roughly equivalent effects on the reduction in sensitivity to area uncertainty in this case study.

MicroRNA signature of the human developing pancreas.

PubMed

Rosero, Samuel; Bravo-Egana, Valia; Jiang, Zhijie; Khuri, Sawsan; Tsinoremas, Nicholas; Klein, Dagmar; Sabates, Eduardo; Correa-Medina, Mayrin; Ricordi, Camillo; Domínguez-Bendala, Juan; Diez, Juan; Pastori, Ricardo L

2010-09-22

MicroRNAs are non-coding RNAs that regulate gene expression including differentiation and development by either inhibiting translation or inducing target degradation. The aim of this study is to determine the microRNA expression signature during human pancreatic development and to identify potential microRNA gene targets calculating correlations between the signature microRNAs and their corresponding mRNA targets, predicted by bioinformatics, in genome-wide RNA microarray study. The microRNA signature of human fetal pancreatic samples 10-22 weeks of gestational age (wga), was obtained by PCR-based high throughput screening with Taqman Low Density Arrays. This method led to identification of 212 microRNAs. The microRNAs were classified in 3 groups: Group number I contains 4 microRNAs with the increasing profile; II, 35 microRNAs with decreasing profile and III with 173 microRNAs, which remain unchanged. We calculated Pearson correlations between the expression profile of microRNAs and target mRNAs, predicted by TargetScan 5.1 and miRBase algorithms, using genome-wide mRNA expression data. Group I correlated with the decreasing expression of 142 target mRNAs and Group II with the increasing expression of 876 target mRNAs. Most microRNAs correlate with multiple targets, just as mRNAs are targeted by multiple microRNAs. Among the identified targets are the genes and transcription factors known to play an essential role in pancreatic development. We have determined specific groups of microRNAs in human fetal pancreas that change the degree of their expression throughout the development. A negative correlative analysis suggests an intertwined network of microRNAs and mRNAs collaborating with each other. This study provides information leading to potential two-way level of combinatorial control regulating gene expression through microRNAs targeting multiple mRNAs and, conversely, target mRNAs regulated in parallel by other microRNAs as well. This study may further the understanding of gene expression regulation in the human developing pancreas.

MicroRNA signature of the human developing pancreas

PubMed Central

2010-01-01

Background MicroRNAs are non-coding RNAs that regulate gene expression including differentiation and development by either inhibiting translation or inducing target degradation. The aim of this study is to determine the microRNA expression signature during human pancreatic development and to identify potential microRNA gene targets calculating correlations between the signature microRNAs and their corresponding mRNA targets, predicted by bioinformatics, in genome-wide RNA microarray study. Results The microRNA signature of human fetal pancreatic samples 10-22 weeks of gestational age (wga), was obtained by PCR-based high throughput screening with Taqman Low Density Arrays. This method led to identification of 212 microRNAs. The microRNAs were classified in 3 groups: Group number I contains 4 microRNAs with the increasing profile; II, 35 microRNAs with decreasing profile and III with 173 microRNAs, which remain unchanged. We calculated Pearson correlations between the expression profile of microRNAs and target mRNAs, predicted by TargetScan 5.1 and miRBase altgorithms, using genome-wide mRNA expression data. Group I correlated with the decreasing expression of 142 target mRNAs and Group II with the increasing expression of 876 target mRNAs. Most microRNAs correlate with multiple targets, just as mRNAs are targeted by multiple microRNAs. Among the identified targets are the genes and transcription factors known to play an essential role in pancreatic development. Conclusions We have determined specific groups of microRNAs in human fetal pancreas that change the degree of their expression throughout the development. A negative correlative analysis suggests an intertwined network of microRNAs and mRNAs collaborating with each other. This study provides information leading to potential two-way level of combinatorial control regulating gene expression through microRNAs targeting multiple mRNAs and, conversely, target mRNAs regulated in parallel by other microRNAs as well. This study may further the understanding of gene expression regulation in the human developing pancreas. PMID:20860821

Individual and social determinants of multiple chronic disease behavioral risk factors among youth.

PubMed

Alamian, Arsham; Paradis, Gilles

2012-03-22

Behavioral risk factors are known to co-occur among youth, and to increase risks of chronic diseases morbidity and mortality later in life. However, little is known about determinants of multiple chronic disease behavioral risk factors, particularly among youth. Previous studies have been cross-sectional and carried out without a sound theoretical framework. Using longitudinal data (n = 1135) from Cycle 4 (2000-2001), Cycle 5 (2002-2003) and Cycle 6 (2004-2005) of the National Longitudinal Survey of Children and Youth, a nationally representative sample of Canadian children who are followed biennially, the present study examines the influence of a set of conceptually-related individual/social distal variables (variables situated at an intermediate distance from behaviors), and individual/social ultimate variables (variables situated at an utmost distance from behaviors) on the rate of occurrence of multiple behavioral risk factors (physical inactivity, sedentary behavior, tobacco smoking, alcohol drinking, and high body mass index) in a sample of children aged 10-11 years at baseline. Multiple behavioral risk factors were assessed using a multiple risk factor score. All statistical analyses were performed using SAS, version 9.1, and SUDAAN, version 9.01. Multivariate longitudinal Poisson models showed that social distal variables including parental/peer smoking and peer drinking (Log-likelihood ratio (LLR) = 187.86, degrees of freedom (DF) = 8, p < .001), as well as individual distal variables including low self-esteem (LLR = 76.94, DF = 4, p < .001) increased the rate of occurrence of multiple behavioral risk factors. Individual ultimate variables including age, sex, and anxiety (LLR = 9.34, DF = 3, p < .05), as well as social ultimate variables including family socioeconomic status, and family structure (LLR = 10.93, DF = 5, p = .05) contributed minimally to the rate of co-occurrence of behavioral risk factors. The results suggest targeting individual/social distal variables in prevention programs of multiple chronic disease behavioral risk factors among youth.

[Type 2 diabetes mellitus and cardiovascular risk factors: is comprehensive treatment required?].

PubMed

Nadal, Josep Franch; Gutiérrez, Pedro Conthe

2013-09-01

Diabetes mellitus, especially type 2, is a metabolic disease involving the coexistence of several cardiovascular risk factors. Affected patients are therefore at high cardiovascular risk (2-3 times higher than that of men in the general population and 2-6 times higher than that of women). Cardiovascular disease is the main cause of death in the diabetic population, followed by cancer. Cardiovascular risk cannot be compared between diabetic patients and persons who have already shown one or more manifestations of cardiovascular disease (such as myocardial infarction). Single risk factors should be evaluated in combination with other risk factors and a person's cardiovascular risk should be individually assessed. Cardiovascular risk assessment in patients with diabetes through current calculations methods is complex because their ability to predict risk in individuals is very low. Studies such as that by Steno have demonstrated the validity of a comprehensive strategy to control all the risk factors present in persons with type 2 diabetes mellitus, which can reduce the development of micro- and macrovascular complications and mortality by almost 50%. The present article reviews each of the classical cardiovascular risk factors (hypertension, dyslipidemia, smoking, obesity, sedentariness) in relation to diabetes, as well as their recommended targets and the benefits of their control. In view of the above, a comprehensive approach is recommended to control the multiple risk factors that can coexist in persons with type 2 diabetes mellitus. Copyright © 2013 Elsevier España, S.L. All rights reserved.

SU-F-T-618: Evaluation of a Mono-Isocentric Treatment Planning Software for Stereotactic Radiosurgery of Multiple Brain Metastases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sham, E; Sattarivand, M; Mulroy, L

Purpose: To evaluate planning performance of an automated treatment planning software (BrainLAB; Elements) for stereotactic radiosurgery (SRS) of multiple brain metastases. Methods: Brainlab’s Multiple Metastases Elements (MME) uses single isocentric technique to treat up to 10 cranial planning target volumes (PTVs). The planning algorithm of the MME accounts for multiple PTVs overlapping with one another on the beam eyes view (BEV) and automatically selects a subset of all overlapping PTVs on each arc for sparing normal tissues in the brain. The algorithm also optimizes collimator angles, margins between multi-leaf collimators (MLCs) and PTVs, as well as monitor units (MUs) usingmore » minimization of conformity index (CI) for all targets. Planning performance was evaluated by comparing the MME-calculated treatment plan parameters with the same parameters calculated with the Volumetric Modulated Arc Therapy (VMAT) optimization on Varian’s Eclipse platform. Results: Figures 1 to 3 compare several treatment plan outcomes calculated between the MME and VMAT for 5 clinical multi-targets SRS patient plans. Prescribed target dose was volume-dependent and defined based on the RTOG recommendation. For a total number of 18 PTV’s, mean values for the CI, PITV, and GI were comparable between the MME and VMAT within one standard deviation (σ). However, MME-calculated MDPD was larger than the same VMAT-calculated parameter. While both techniques delivered similar maximum point doses to the critical cranial structures and total MU’s for the 5 patient plans, the MME required less treatment planning time by an order of magnitude compared to VMAT. Conclusion: The MME and VMAT produce similar plan qualities in terms of MUs, target dose conformation, and OAR dose sparing. While the selective use of PTVs for arc-optimization with the MME reduces significantly the total planning time in comparison to VMAT, the target dose homogeneity was also compromised due to its simplified inverse planning algorithm used.« less

Post-Traumatic Stress Disorder after childbirth and the influence of maternity team care during labour and birth: A cohort study.

PubMed

De Schepper, Sarah; Vercauteren, Tinne; Tersago, Jolein; Jacquemyn, Yves; Raes, Filip; Franck, Erik

2016-01-01

we examined the prevalence of Post-Traumatic Stress Disorder (PTSD) and the role of personal and obstetric risk factors, as well as the role of midwifery team care factors in a cohort of Flemish women. prospective cohort study. Data collection was performed at two times post partum: During the first week, socio-demographic and obstetric data as well as information related to midwifery team care factors were assessed using self-report measures. To asses PTSD symptomatology, the Impact of Event Scale-Revised (IES-R) and the Traumatic Event Scale (TES) were used. At six weeks post partum, PTSD symptoms were reassessed either by telephone interviews or e-mail. Results were calculated in frequencies, means and standard deviations. Differences between week one and six were analysed using parametrical and non-parametrical statistics. Multiple and logistic regression was performed to determine risk factors for PTSD symptomatology. P-value was set at 0.05. maternity wards in Flanders, Belgium. the first (week 1) and follow-up (week 6) sample of the data collection consisted of 340 and 229 women respectively. the prevalence of PTSD symptoms after childbirth ranged from 22% to 24% in the first week and from 13% to 20% at six weeks follow-up. Multiple regression analysis showed that Islamic belief, a traumatic childbirth experience, family income <€2500, a history of psychological or psychiatric consults and labour/birth with complications significantly predicted PTSD symptomatology at six weeks post-birth. Midwifery team care and the opportunity to ask questions, as well as experiencing a normal physiological birth were significantly associated with less postnatal PTSD symptoms. KEY CONCLUSIONS AND IMPLICATIONS FOR PRACTISE: the results of this study suggest that contextual factors such as religion, socio-economic status, and childbirth experience might be important factors to address by the midwifery team. Midwifery team care factors such as 'providing the opportunity to the mother to ask questions' and the 'perception of the midwife being in control' proved to be potential protective factors for postnatal PTSD symptoms. Despite its prevalence, PTSD symptoms after birth are not yet well understood by health care workers. Further research concerning the influence of midwifery team care factors on developing childbirth related PTSD is required. Copyright © 2015 Elsevier Ltd. All rights reserved.

Predictors of postoperative outcomes of cubital tunnel syndrome treatments using multiple logistic regression analysis.

PubMed

Suzuki, Taku; Iwamoto, Takuji; Shizu, Kanae; Suzuki, Katsuji; Yamada, Harumoto; Sato, Kazuki

2017-05-01

This retrospective study was designed to investigate prognostic factors for postoperative outcomes for cubital tunnel syndrome (CubTS) using multiple logistic regression analysis with a large number of patients. Eighty-three patients with CubTS who underwent surgeries were enrolled. The following potential prognostic factors for disease severity were selected according to previous reports: sex, age, type of surgery, disease duration, body mass index, cervical lesion, presence of diabetes mellitus, Workers' Compensation status, preoperative severity, and preoperative electrodiagnostic testing. Postoperative severity of disease was assessed 2 years after surgery by Messina's criteria which is an outcome measure specifically for CubTS. Bivariate analysis was performed to select candidate prognostic factors for multiple linear regression analyses. Multiple logistic regression analysis was conducted to identify the association between postoperative severity and selected prognostic factors. Both bivariate and multiple linear regression analysis revealed only preoperative severity as an independent risk factor for poor prognosis, while other factors did not show any significant association. Although conflicting results exist regarding prognosis of CubTS, this study supports evidence from previous studies and concludes early surgical intervention portends the most favorable prognosis. Copyright © 2017 The Japanese Orthopaedic Association. Published by Elsevier B.V. All rights reserved.

NON-MENDELIAN ETIOLOGIC FACTORS IN NEUROPSYCHIATRIC ILLNESS: PLEIOTROPY, EPIGENETICS, AND CONVERGENCE

PubMed Central

Deutsch, Curtis K; McIlvane, William J

2013-01-01

The target article by Charney on behavior genetics/genomics discusses how numerous molecular factors can inform heritability estimations and genetic association studies. These factors find application in the search for genes for behavioral phenotypes, including neuropsychiatric disorders. We elaborate upon how single causal factors can generate multiple phenotypes, and discuss how multiple causal factors may converge on common neurodevelopmental mechanisms. PMID:23095384

Demographic, genetic, and environmental factors that modify disease course.

PubMed

Marrie, Ruth Ann

2011-05-01

As with susceptibility to disease, it is likely that multiple factors interact to influence the phenotype of multiple sclerosis and long-term disease outcomes. Such factors may include genetic factors, socioeconomic status, comorbid diseases, and health behaviors, as well as environmental exposures. An improved understanding of the influence of these factors on disease course may reap several benefits, such as improved prognostication, allowing us to tailor disease management with respect to intensity of disease-modifying therapies and changes in specific health behaviors, in the broad context of coexisting health issues. Such information can facilitate appropriately adjusted comparisons within and between populations. Elucidation of these factors will require careful study of well-characterized populations in which the roles of multiple factors are considered simultaneously. Copyright © 2011 Elsevier Inc. All rights reserved.

Quantitative analysis of titanium-induced artifacts and correlated factors during micro-CT scanning.

PubMed

Li, Jun Yuan; Pow, Edmond Ho Nang; Zheng, Li Wu; Ma, Li; Kwong, Dora Lai Wan; Cheung, Lim Kwong

2014-04-01

To investigate the impact of cover screw, resin embedment, and implant angulation on artifact of microcomputed tomography (micro-CT) scanning for implant. A total of twelve implants were randomly divided into 4 groups: (i) implant only; (ii) implant with cover screw; (iii) implant with resin embedment; and (iv) implants with cover screw and resin embedment. Implants angulation at 0°, 45°, and 90° were scanned by micro-CT. Images were assessed, and the ratio of artifact volume to total volume (AV/TV) was calculated. A multiple regression analysis in stepwise model was used to determine the significance of different factors. One-way ANOVA was performed to identify which combination of factors could minimize the artifact. In the regression analysis, implant angulation was identified as the best predictor for artifact among the factors (P < 0.001). Resin embedment also had significant effect on artifact volume (P = 0.028), while cover screw had not (P > 0.05). Non-embedded implants with the axis parallel to X-ray source of micro-CT produced minimal artifact. Implant angulation and resin embedment affected the artifact volume of micro-CT scanning for implant, while cover screw did not. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.