Effects of environmental factors on monuments: the Harkhuf Tomb in Aswan, Egypt

NASA Astrophysics Data System (ADS)

Baldi, Marina

2015-04-01

The tombs of the nobles excavated in the rocks on the Nile west bank at Qubbet el-Hawa in Aswan (Egypt) testify the role of the city as the southern gate of Egypt. In old times Aswan was the starting point of caravans travelling far south in uncovered territories and bringing back precious and exotic goods. Inscriptions on the tombs reflect the explorations and trades of that time and the cultural exchanges with southern territories. Nowadays the tombs, exposed to the environmental factors - wind, sun, rainfall - and to air polluttants originated from the town of Aswan are under a fast deterioration process. It is therefore necessary a full documentation of the tombs and of their façade and a study of the deterioration process due to the impact of the environmental factors. As a case study the tomb of Harkhuf at Qubbet el-Hawa has been chosen, because of its importance, its status of decay, and for the old documentation by the Italian Egyptologist E. Schiaparelli. The climate factors affecting the tomb of Harkhuf are air temperature, its diurnal excursion, and wind, and, at some extent, relative humidity. In fact, in Aswan, night time Humidity can be more than 30% during the winter months, while precipitation is a very rare event occurring once every 1 or 2 years, but has important impact due to its high intensity and short duration with devastating impact on manufact and structures in the area. The experiment, designed using portable meteorological instruments, permitted to define if the microclimate near the Harkhuf Tomb has the same characteristics of the larger Aswan area which can be derived by the meteorological station located at the Aswan airport. However differences in the microclimate are evident and preliminary analysis of data collected between 8:00 am and 4:00 pm during some consecutive days will be presented. The study permitted to identify and measure the differential heating of the façade, with the right part reaching temperatures much warmer than

Technologies Applied in the Toshka Project of Egypt

ERIC Educational Resources Information Center

Wahby, Wafeek S.

2004-01-01

The Toshka Project, located in Egypt, involves excavating a canal to carry about 380 billion ft[supercript 3] of water every year from Lake Nasser to the Toshka Depression, southwest of Aswan. This will eventually create a new valley to the River Nile in the western desert of Egypt in addition to the currently existing prehistoric river course.…

Driving change: an interview with Ford Motor Company's Jacques Nasser. Interview by Suzy Wetlaufer.

PubMed

Nasser, J

1999-01-01

What happens when the world is changing but your organization isn't? And what if that organization has 340,000 employees in 200 countries? In this interview, Jacques Nasser, the new CEO of Ford Motor Company, talks with HBR editor Suzy Wetlaufer about these challenges and explains how his company is overcoming them through a unique education program. Since its very beginnings, says Nasser, Ford has comprised dozens of far-flung divisions and units, each with its own "fiefdom" mind-set. The fiefdoms didn't share information, let alone great ideas. Such behavior stifled creativity and drove up costs. Today's global environment demands a new and different way of doing business, says Nasser, and to that end, Ford has launched a multifaceted teaching initiative that will reach every one of Ford's employees by year-end. The goal of the program: to help employees view the company in its entirety as shareholders do, and then act that way too. At the heart of the initiative is the teachable point of view, a five-part written explanation of what a person knows and believes about what it takes to succeed in business. It is more than just a document to be discussed and then filed. It has proven to be a powerful tool for organizational transformation, and not only at Ford. In a commentary accompanying Nasser's interview, Noel Tichy, leadership expert and consultant to Ford describes the building blocks of the teachable point of view and explores how it can be implemented in any organization determined to change for the better.

Water Management Models in Practice: A Case Study of the Aswan High Dam

NASA Astrophysics Data System (ADS)

El-Ashry, M. T.; Alford, D. L.

1984-04-01

The stated purpose of this volume is the development and evaluation of operating policies for the Aswan High Dam and their relation to the development of water resources policy in Egypt. That objective is admirably fulfilled through discussions of water use in Egypt and the operation objectives of the High Dam, the behavior of the physical system and simulation of the reservoir, a realtime management model of the dam, management of water shortages and trade-offs between major uses, and coordinated operation of the dam with new upstream as well as downstream developments.The High Dam has been a source of controversy, particularly with regard to its environmental impacts. Its adverse effects include changes in the water table and attendant salt buildup in irrigated areas, excessive growth of aquatic plants below the dam, shoreline erosion, and increases in water-borne diseases such as schistosomiasis (bilharzia). The dam was intended to offset rapid population growth by increasing food supplies through the transformation of irrigated land in southern Egypt from seasonal to perennial cultivation and by providing water for the reclamation of desert land. Unfortunately, such benefits have been outstripped by the rapidly growing population, and water shortages will be experienced by the end of the century.

The New Frontier on the Nile: JFK, Nasser, and Arab Nationalism.

ERIC Educational Resources Information Center

Little, Douglas

1988-01-01

Examines John F. Kennedy's negotiations with Egypt's Gamel Abdel Nasser as he attempted to improve U.S.-Arab relations and prevent the spread of Soviet influence in the Middle East region. States that Kennedy's failure to meet his Middle Eastern objectives resulted from his inability to reconcile the many factions dividing the Arab world. (GEA)

Earth observations taken by the Expedition 12 crew

NASA Image and Video Library

2005-11-15

ISS012-E-11654 (11 Dec. 2005) --- Lake Nasser and New Valley, Egypt are featured in this image photographed by an Expedition 12 crew member on the International Space Station. Cycles of flood and drought in the African Sahel are legendary, and they have provided the impetus for major waterworks on Africa’s great rivers. The construction of the Aswan High Dam on the Nile River, creating Lake Nasser in the 1960s, is the biggest and most visible project. Heavy rains in the source regions of the Nile in the 1990s resulted in record water levels in Lake Nasser. The abundance of water facilitated the Egyptian government’s promotion of another massive water distribution system called New Valley. In 1997, Lake Nasser flooded westward down a spillway into the Toshka depression in southern Egypt, creating four new lakes over the next few years. Following the initial flooding, a pumping station and canal were constructed in 2000 to maintain water flow into the region, allowing for industrial and agricultural development in the desert. This view shows the completed Mubarek Pumping Station on Lake Nasser; the spillway that originally flooded the Toshka depression and the southern end of the first of the Toshka Lakes; part of the 50-kilometer-long main canal (the Sheikh Zayed Canal); side canals; and several new fields in the Egyptian desert northwest of Lake Nasser. Astronauts, cosmonauts and space-based sensors have been monitoring these developments in Egypt since their inception in the late 1990s. New Valley’s Toshka Lakes, and the new developments surrounding them, represent one of the most visible and rapid man-made changes on Earth’s surface.

Earth Observation

NASA Image and Video Library

2014-08-23

ISS040-E-105768 (23 Aug. 2014) --- One of the Expedition 40 crew members aboard the International Space Station, flying at an altitude of 221 nautical miles, captured this image of Egypt's Nile River and Lake Nasser on Aug. 23, 2014. The Aswan High Dam is to the right of center in the 70mm focal-length image, as the Nile flows southward (to the right in this image) toward Cairo and it?s Mediterranean delta (both out of frame at right). The Red Sea, which runs more or less parallel to the Nile, is out of frame at bottom.

Geophysical characterization of the role of fault and fracture systems for recharging groundwater aquifers from surface water of Lake Nasser

NASA Astrophysics Data System (ADS)

Mansour, Khamis; Omar, Khaled; Ali, Kamal; Abdel Zaher, Mohamed

2018-06-01

The role of the fracture system is important for enhancing the recharge or discharge of fluids in the subsurface reservoir. The Lake Nasser is consider one of the largest artificial lakes all over the world and contains huge bulk of storage water. In this study, the influence of fracture zones on subsurface fluid flow in groundwater reservoirs is investigated using geophysical techniques including seismicity, geoelectric and gravity data. These data have been utilized for exploring structural structure in south west Lake Nasser, and subsurface discontinuities (joints or faults) notwithstanding its related fracture systems. Seismicity investigation gave us the comprehension of the dynamic geological structure sets and proposing the main recharging paths for the Nubian aquifer from Lake Nasser surface water. Processing and modelling of aerogravity data show that the greater thickness of sedimentary cover (700 m) is located eastward and northward while basement outcrops occur at Umm Shaghir and Al Asr areas. Sixty-nine vertical electrical soundings (VES's) were used to delineate the subsurface geoelectric layers along eight profiles that help to realize the subsurface geological structure behind the hydrogeological conditions of the studied area.

Aswan High Dam in 6-meter Resolution from the International Space Station

NASA Technical Reports Server (NTRS)

2002-01-01

Astronaut photography of the Earth from the International Space Station has achieved resolutions close to those available from commercial remote sensing satellites-with many photographs having spatial resolutions of less than six meters. Astronauts take the photographs by hand and physically compensate for the motion of the spacecraft relative to the Earth while the images are being acquired. The achievement was highlighted in an article entitled 'Space Station Allows Remote Sensing of Earth to within Six Meters' published in this week's edition of Eos, Transactions of the American Geophysical Union. Lines painted on airport runways at the Aswan Airport served to independently validate the spatial resolution of the camera sensor. For press information, read: International Space Station Astronauts Set New Standard for Earth Photography For details, see Robinson, J. A. and Evans, C. A. 2002. Space Station Allows Remote Sensing of Earth to within Six Meters. Eos, Transactions, American Geophysical Union 83(17):185, 188. See some of the other detailed photographs posted to Earth Observatory: Pyramids at Giza Bermuda Downtown Houston The image above represents a detailed portion of a digitized NASA photograph STS102-303-17, and was provided by the Earth Sciences and Image Analysis Laboratory at Johnson Space Center. Additional images taken by astronauts and cosmonauts can be viewed at the NASA-JSC Gateway to Astronaut Photography of Earth.

Apollo 9 Mission image - United Arab Republic,Nile River,Red Sea and Aswan Dam

NASA Image and Video Library

1969-03-03

Oblique Earth Observation taken by the Apollo 9 crew. View is the United Arab Republic,the Nile River,The Red Sea and the Aswan Dam. Film magazine was E,film type was SO-368 Ektachrome with 0.460 - 0.710 micrometers film / filter transmittance response and haze filter,80mm lens. Latitude was 19.38 N by Longitude 30.24 E, Overlap was 50%, Altitude was 97 nautical miles and cloud cover was 5%.

Attenuation of coda waves in the Aswan Reservoir area, Egypt

NASA Astrophysics Data System (ADS)

Mohamed, H. H.; Mukhopadhyay, S.; Sharma, J.

2010-09-01

Coda attenuation characteristics of Aswan Reservoir area of Egypt were analyzed using data recorded by a local earthquake network operated around the reservoir. 330 waveforms obtained from 28 earthquakes recorded by a network of 13 stations were used for this analysis. Magnitude of these earthquakes varied between 1.4 and 2.5. The maximum epicentral distance and depth of focus of these earthquakes were 45 km and 16 km respectively. Single back-scattering method was used for estimation of coda Q ( Qc). The Q0 values ( Qc at 1 Hz) vary between 54 and 100 and frequency dependence parameter " n" values vary between 1 and 1.2 for lapse time varying between 15 s and 60 s. It is observed that coda Q ( Qc) and related parameters are similar at similar lapse times to those observed for those for Koyna, India, where reservoir induced seismicity is also observed. For both regions these parameters are also similar to those observed for tectonically active regions of the world, although Aswan is located in a moderately active region and Koyna is located in a tectonically stable region. However, Qc does not increase uniformly with increasing lapse time, as is observed for several parts of the world. Converting lapse time to depth/distance it is observed that Qc becomes lower or remains almost constant at around 70 to 90 km and 120 km depth/distance. This indicates presence of more attenuative material at those depth levels or distances compared to their immediate surroundings. It is proposed that this variation indicates presence of fluid filled fractures and/or partial melts at some depths/distance from the area of study. The Qc values are higher than those obtained for the Gulf of Suez and Al Dabbab region of Egypt at distances greater than 300 km from the study area by other workers. The turbidity decreases with depth in the study area.

Management of acute ischaemic stroke at Nasser Hospital, Gaza Strip: a clinical audit.

PubMed

Alkhatib, Mohammed N; Abd-Alghafoor, Tamer; Elmassry, AlaaEldeen; Albarqouni, Loai; Böttcher, Bettina; Alfaqawi, Maha

2018-02-21

Stroke is a leading cause of morbidity and mortality worldwide. The aim of this study was to assess the standard of care for patients with acute ischaemic stroke at the internal medicine department of Nasser Hospital, Gaza Strip. For this retrospective clinical audit, we selected a random sample of 100 medical records for patients with stroke who were admitted to Nasser Hospital between January and August, 2016. Clinical practice was compared with the recommendations in the 2013 American Heart Association and American Stroke Association guidelines. Patient confidentiality was maintained, and ethical approval was obtained from the Palestinian Ministry of Health. Five patient records were not coded and therefore excluded. Of the remaining 95 patients, 51 (54%) were men with a mean age of 67 years (SD 14). 53 patients presented with dysarthria. The duration of stroke symptoms before admission was not reported in 86 (91%) records. A complete blood count and renal function tests were done for all patients, lipid profiling for 87 (92%) patients, electrocardiography for 85 (89%) patients, carotid duplex ultrasound for 32 (34%) patients, and CT scan for all patients. None of the patients had continuous cardiac monitoring or an assessment of swallowing function, and 70 (74%) patients received immediate anti-platelet therapy (325 mg aspirin). 80 (85%) patients received venous thromboembolism prophylaxis. 41 (43%) patients were given antibiotics without a recorded indication. None of the patients received thrombolytic therapy. As recommended in the guidelines, 41 (43%) patients did not receive anti-hypertensive agents on the first day of hospitalisation. 46 (48%) patients had diabetes, and glycaemic control was achieved by day 3 in 26 (57%) patients. No Palestinian guidelines exist for the management of patients with acute ischaemic stroke, and in most cases management was based on personal experience rather than evidence. The development of evidence-based guidelines is

Visualizing a monumental past: Archeology, Nasser's Egypt, and the early Cold War.

PubMed

Carruthers, William

2017-09-01

This article examines geographies of decolonization and the Cold War through a case study in the making of archeological knowledge. The article focuses on an archeological dig that took place in Egypt in the period between the July 1952 Free Officers' coup and the 1956 Suez crisis. Making use of the notion of the 'boundary object', this article demonstrates how the excavation of ancient Egyptian remains at the site of Mit Rahina helped to constitute Nasserist revolutionary modernity and its relationship to wider, post-Second World War political geographies. The dig took place as a result of an Egyptian-American collaboration designed to institute the possibility of archeology taking place along the lines of the Point Four modernization program promoted by the United States. The article discusses how this situation not only engendered contention surrounding the role of the international 'experts' appointed to run this excavation work, but also - and as a result - helped to constitute the monumental visual and material shape that archeological evidence relating to the Egyptian past could now take. Egypt's revolution sat within wider Cold War political struggles, yet the 'ground-up' realities of this relationship helped to constitute the sort of past (and future) monumentality proposed by Nasser's government.

Trace elements assessment in agricultural and desert soils of Aswan area, south Egypt: Geochemical characteristics and environmental impacts

NASA Astrophysics Data System (ADS)

Darwish, Mohamed Abdallah Gad; Pöllmann, Hebert

2015-12-01

Determination of chemical elements, Al, Cd, Co, Cr, Cu, Fe, Li, Mn, Mo, Ni, P, Pb, Sc, Sr, Ti, Y, and Zn have been performed in agricultural and desert soils and alfalfa (Medicago sativa) at Aswan area. Consequently, the pollution indices, univariate and multivariate statistical methods have been applied, in order to assess the geochemical characteristics of these elements and their impact on soil environmental quality and plant, and to reach for their potential input sources. The investigation revealed that the mean and range values of all element concentrations in agricultural soil are higher than those in desert soil. Furthermore, the agricultural soil displayed various degrees of enrichment and pollution of Cd, Zn, Mo, Co, P, Ti, Pb. The geochemical pattern of integrated pollution indices gave a clear image of extreme and strong pollution in the agricultural soil stations, their poor quality with high risk to human health and considered as a tocsin for an alert. In contrast, the desert soil is the good environmental quality and safe for plant, animal and human health. Alfalfa is tolerant plant and considered as a biomarker for P and Mo in polluted agricultural soil. Four geochemical associations of analyzing elements in agricultural soil and three ones in desert soil have been generated, and their enhancements were essentially caused by various anthropogenic activities and geogenic sources. The investigation also revealed that the broad extended desert soil is fruitful and promising as cultivable lands for agricultural processes in the futures.

Modeling the Impact of controlled flow and sediment releases for the restoration of the Nile Delta, Egypt

NASA Astrophysics Data System (ADS)

Al-Zaidi, B. M.; Moussa, A.; Viparelli, E.

2017-12-01

The construction of the High and Old Aswan Dams and of barrages significantly altered the flow and the sediment transport regimes in the Egyptian reach of the Nile River. The field data collected by the Nile Research Institute show that the post-High Aswan Dam Nile River hydrology is characterized by reductions of more than 70% in flow discharge and 98% in sediment load compared to pre-High Aswan Dam conditions. A significant portion of discharge released from the dams is diverted at the barrages for agricultural ( 80%) and municipal ( 15%) uses. Thus, virtually no water is reaching the Nile Delta and the Mediterranean Sea. Consequently, the sediment load delivered to the Mediterranean Sea is negligible compared to pre-dam conditions. Consequences of the flow regulation are delta wide wetland loss and shoreline retreat, widespread delta pollution, reduction soil quality, salination of cultivated land, wetland losses, and saltwater intrusion in the groundwater. Here we present the second part of a feasibility study for the restoration of the Nile River-Delta system characterized by controlled flow releases and sediment augmentations downstream of the High Aswan Dam. The controlled flow releases are obtained by regulating the current releases from the High Aswan Dam at the Old Aswan Dam, which is located 6.5 km downstream of the High Aswan Dam. Previous studies showed that 10 billion m3 of water can be saved annually by improving the Egyptian irrigation system. Here we propose to use the saved water to increase the water discharge to the Nile Delta, i.e., the total volume of water released from the dams does not change, what changes is the water used and the imposed hydrograph. We modulate the river flow by storing the saved water during the agriculture season upstream of the Old Aswan Dam and releasing it in the months coinciding with the natural river flood season. It is important to note that here we are considering the simplest possible scenario for water storage

Effect of site on sedimentological characteristics and metal pollution in two semi-enclosed embayments of great freshwater reservoir: Lake Nasser, Egypt

NASA Astrophysics Data System (ADS)

Farhat, Hassan I.; Aly, Walid

2018-05-01

This study was carried out to assess the effect of site on the spatial variations of sedimentological characteristics and heavy metal pollution of two semi-enclosed embayments of Lake Nasser. Grain Size, texture and mode of transportation as well as some heavy metals and organic matter were assessed in sediment samples from those embayments. The results indicated that the grain size of the lake sediments was affected by site variation. Moreover, heavy metal distribution in the sediments was mainly directed by grain size distribution and organic matter, though, the organic matter was more critical than grain size in controlling heavy metals distribution in each embayment. The main source of heavy metals in studied embayments was concluded to be the metals brought with flood waters rather than being of anthropogenic origin. The results also indicated the association of studied metals with Fe and Mn oxides of suspended matters and dissolved solids which come with flood water and trapped and settled to the bottom sediment in the stagnation period. Measured indices indicated that southern embayment is more polluted than northern one, which could be explained on the basis that the southern embayment reserves larger amounts of suspended matter coming with the flood than northern embayment.

Natural radionuclide concentrations in granite rocks in Aswan and Central-Southern Eastern Desert, Egypt and their radiological implications.

PubMed

Issa, Shams A M; Uosif, M A M; Abd el-Salam, L M

2012-07-01

Different types of granites, used extensively in local construction, were collected from five localities in Egypt, namely: Abu Ziran (Central Eastern Desert), Gabal El Maesala (Aswan) and three areas from Wadi Allaqi, (Gabal Abu Marw, Gabal Haumor and Gabal um Shalman), in the South Eastern Desert. Granite samples were studied radiologically, petrographically and geochemically. The contents of natural radionuclides ((226)Ra, (232)Th and (40)K) were measured in investigated samples by using gamma spectrometry [NaI (Tl) 3'×3']. The activity concentrations of (226)Ra, (232)Th and (40)K in the selected granite samples ranged from 9±0.5 to 111±7, 8±1 to 75±4 and 100±6 to 790±40 Bq kg(-1), respectively. The external hazard index (H(ex)), absorbed dose and annual effective dose rate were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. The calculated radium equivalents were lower than the values recommended for construction materials (370 Bq kg(-1)). The excess lifetime cancer risks were also calculated. Petrographically, the granites studied are varied in the form of potash-feldspar, quartz, plagioclase, mica and hornblende. The accessory minerals are zircon, apatite and allanite. Geochemically, the chemical composition of the granite is studied especially for major oxides. They are characterized to have SiO(2), K(2)O, Na(2)O and Al(2)O(3) with depletion in CaO, MgO, TiO(2) and P(2)O(5).

Exploiting Terrorist Vulnerabilities: A Law Enforcement Approach to Fighting Terrorist Organizations

DTIC Science & Technology

2009-05-01

assassination led to a crackdown by the Egyptian Government. This crackdown led to an alliance with Gamal Abdel Nasser. Nasser promised a return to......He believed that the Western powers were bleeding Egyptian resources dry. He was firmly against capitalism and formed a social welfare network

A sampling design and model for estimating abundance of Nile crocodiles while accounting for heterogeneity of detectability of multiple observers

USGS Publications Warehouse

Shirley, Matthew H.; Dorazio, Robert M.; Abassery, Ekramy; Elhady, Amr A.; Mekki, Mohammed S.; Asran, Hosni H.

2012-01-01

As part of the development of a management program for Nile crocodiles in Lake Nasser, Egypt, we used a dependent double-observer sampling protocol with multiple observers to compute estimates of population size. To analyze the data, we developed a hierarchical model that allowed us to assess variation in detection probabilities among observers and survey dates, as well as account for variation in crocodile abundance among sites and habitats. We conducted surveys from July 2008-June 2009 in 15 areas of Lake Nasser that were representative of 3 main habitat categories. During these surveys, we sampled 1,086 km of lake shore wherein we detected 386 crocodiles. Analysis of the data revealed significant variability in both inter- and intra-observer detection probabilities. Our raw encounter rate was 0.355 crocodiles/km. When we accounted for observer effects and habitat, we estimated a surface population abundance of 2,581 (2,239-2,987, 95% credible intervals) crocodiles in Lake Nasser. Our results underscore the importance of well-trained, experienced monitoring personnel in order to decrease heterogeneity in intra-observer detection probability and to better detect changes in the population based on survey indices. This study will assist the Egyptian government establish a monitoring program as an integral part of future crocodile harvest activities in Lake Nasser

Go with the Floe: Geostrategic Ramifications of a Changing Artic

DTIC Science & Technology

2014-06-01

bolstered Arctic power will gain options by maintaining a presence in Iceland. China is courting Iceland enthusiastically.29 Beijing is not the only...valid OMB control number. 1. REPORT DATE JUN 2014 2. REPORT TYPE 3. DATES COVERED 00-00-2014 to 00-00-2014 4. TITLE AND SUBTITLE Go With The...winning war against Nasser???s Egypt in 1956, which ended up costing Great Britain control of the canal. 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF

Economic Development: The Quest for Material Well-Being. Instructional Activities Series IA/S-7.

ERIC Educational Resources Information Center

Veal, Willis D.

This activity is one of a series of 17 teacher-developed instructional activities for geography at the secondary-grade level described in SO 009 140. The activity investigates economic change in developing nations. It employs the dialogue approach. Given data about the Aswan High Dam in Egypt and about the environment of northeast Africa, students…

Wetland vegetation in Manzala lagoon, Nile Delta coast, Egypt: Rapid responses of pollen to altered nile hydrology and land use

USGS Publications Warehouse

Bernhardt, C.E.; Stanley, J.-D.; Horton, B.P.

2011-01-01

The pollen record in a sediment core from Manzala lagoon on the Nile delta coastal margin of Egypt, deposited from ca. AD 1860 to 1990, indicates rapid coastal wetland vegetation responses to two primary periods of human activity. These are associated with artificially altered Nile hydrologic regimes in proximal areas and distal sectors located to ???1200 km south of Manzala. Freshwater wetland plants that were dominant, such as Typha and Phragmites, decreased rapidly, whereas in the early 1900s, brackish water wetland species (e.g., Amaranthaceae) increased. This change occurred after closure of the Aswan Low Dam in 1902. The second major modification in the pollen record occurred in the early 1970s, after Aswan High Dam closure from 1965 to 1970, when Typha pollen abundance increased rapidly. Massive population growth occurred along the Nile during the 130 years represented by the core section. During this time, the total volume of lagoon water decreased because of conversion of wetland areas to agricultural land, and input of organic-rich sediment, sewage (municipal, agricultural, industrial), and fertilizer in Manzala lagoon increased markedly. Although the wetland plant community has continued to respond to increasingly intensified and varied human-induced pressures in proximal sectors, the two most marked changes in Manzala pollen best correlate with distal events (i.e., closure of the two dams at Aswan). The study also shows that the two major vegetation changes in Manzala lagoon each occurred less than 10 years after closure upriver of the Low and High dams that markedly altered the Nile regime from Upper Egypt to the coast. ?? 2011, the Coastal Education & Research Foundation (CERF).

Relationship of carbohydrates and lignin molecular structure spectral profiles to nutrient profile in newly developed oats cultivars and barley grain

NASA Astrophysics Data System (ADS)

Prates, Luciana Louzada; Refat, Basim; Lei, Yaogeng; Louzada-Prates, Mariana; Yu, Peiqiang

2018-01-01

The objectives of this study were to quantify the chemical profile and the magnitude of differences in the oat and barley grain varieties developed by Crop Development Centre (CDC) in terms of Cornell Net Carbohydrate Protein System (CNCPS) carbohydrate sub-fractions: CA4 (sugars), CB1 (starch), CB2 (soluble fibre), CB3 (available neutral detergent fibre - NDF), and CC (unavailable carbohydrate); to estimate the energy values; to detect the lignin and carbohydrate (CHO) molecular structure profiles in CDC Nasser and CDC Seabiscuit oat and CDC Meredith barley grains by using Fourier transform infrared attenuated total reflectance (FTIR-ATR); to develop a model to predict nutrient supply based on CHO molecular profile. Results showed that NDF, ADF and CHO were greater (P < 0.05) in oat than in barley. The starch content was greater (P < 0.05) in barley than in oat. The CDC Meredith showed greater total rumen degradable carbohydrate (RDC), intestinal digestible fraction carbohydrate (FC) and lower total rumen undegradable carbohydrate (RUC). However, the estimated milk production did not differ for CDC Nasser oat and CDC Meredith barley. Lignin peak area and peak height did not differ (P > 0.05) for oat and barley grains as well as non-structural CHO. However, cellulosic compounds peak area and height were greater (P < 0.05) in oat than barley grains. Multiple regressions were determined to predict nutrient supply by using lignin and CHO molecular profiles. It was concluded that although there were some differences between oat and barley grains, CDC Nasser and CDC Meredith presented similarities related to chemical and molecular profiles, indicating that CDC Meredith barley could be replaced for CDC Nasser as ruminant feed. The FTIR was able to identify functional groups related to CHO molecular spectral in oat and barley grains and FTIR-ATR results could be used to predict nutrient supply in ruminant livestock systems.

Combining satellite image data and field observations to characterize fresh-water carbonates in Kurkur Oasis, Southern Egypt

NASA Astrophysics Data System (ADS)

Gaber, Ahmed; Khalaf, Fikry; Bastawisy, Mohamed; El-Baz, Farouk

2018-03-01

Several fresh-water carbonate deposits (tufa and travertine) were formed at different elevations within the Kurkur paleolake, 50 km west of Aswan, Egypt. Such paleolake was unique and confined in sag between the cuesta and the capping platform of Sin El-Kaddabaa Plateau. This work aims at integrating the remote sensing data together with the chemical and petrographic analyses to map and characterize these tufa and travertine deposits to define their paleo-depositional environment. A DEM with 2.5 m spatial resolution was generated from two ALOS/PRISM images to show geomorphological and hydrological parameters. In addition, full-polarimetric SAR data were used to investigate the scattering response of these tufa and travertine deposits. These deposits show a volume scattering response, with an increase in the pedestal height of the co- and cross-polarized signatures. The tufa and travertine deposits range from Pleistocene (older upper level) to Recent (younger lower level). The young tufa is hard, light brown porous and thinly-laminated, while the old tufa is generally coarse crystalline and consists of columnar pseudo denderitic calcite crystals. The travertine displays a stromatolitic fabric, where thin dark micritic algal laminae alternate with relatively thick calcitic bands (∼1 cm). Conducted XRD and chemical analyses reveal that these tufa and travertine are entirely composed of low magnesium calcite, with traces of quartz (<2%). Moreover, the δ13C and δ18O values suggest that the old tufa have been developed during warm pluvial periods, while the younger ones were precipitated in drier periods. Two hypotheses were introduced to explain the changes in the hydrological regime of Kurkur paleolake; the first proposes a hydrological breaching due to water overflow on the lake's low periphery areas that led to their desiccation (where the tufa and travertine were deposited) and the second is the possible integration into the regional drainage networks of the

Egypt and Red Sea

NASA Technical Reports Server (NTRS)

1982-01-01

A panaramic view of eastern Egypt, The Red Sea and Saudi Arabia beyond (24.0N, 33.0E). In this desert country, where water is life, the high Aswan Dam and the impounded waters of the Nile River in the foreground assure water availability into the next century. The Red Sea beyond, part of the Suez Canal seaway, serves as a commercial link to the world and separates Egypt from Saudi Arabia.

Eastern Egypt, Red Sea and Saudi Arabia

NASA Image and Video Library

1990-04-29

STS031-79-015 (24-29 April 1990) --- The 330-plus nautical mile orbital altitude of the Space Shuttle Discovery allowed for this unique high oblique 70mm Hasselblad frame. Egypt is in the foreground, with the Nile River and Lake Nasser readily identifiable. Cairo and Alexandria are visible. The Mediterranean Sea is on the horizon in upper left. The Red Sea is in the center. Other areas seen include Saudi Arabia, Jordan, Palestine and Israel; the Gulf of Aqaba and the Gulf of Suez.

Earth Observations taken by STS-119 Crewmember.

NASA Image and Video Library

2009-03-27

S119-E-010832 (27 March 2009) --- On its final full day in space before its scheduled return home on March 28, the crew of Space Shuttle Discovery took some pictures of the home planet. This view shows Lake Nasser in Egypt, under scattered clouds.

Earth Observation taken during Joint Operations

NASA Image and Video Library

2009-07-23

S127-E-008040 (23 July 2009) --- This is a view of Egypt's Lake Nasser from the shuttle-station tandem currently flying 220 miles above Earth. An international crew of thirteen astronauts and cosmonaut are working together to continue work on the orbital outpost

The effects of a test-taking strategy intervention for high school students with test anxiety in advanced placement science courses

NASA Astrophysics Data System (ADS)

Markus, Doron J.

Test anxiety is one of the most debilitating and disruptive factors associated with underachievement and failure in schools (Birenbaum, Menucha, Nasser, & Fadia, 1994; Tobias, 1985). Researchers have suggested that interventions that combine multiple test-anxiety reduction techniques are most effective at reducing test anxiety levels (Ergene, 2003). For the current study, involving 62 public high school students enrolled in advanced placement science courses, the researcher designed a multimodal intervention designed to reduce test anxiety. Analyses were conducted to assess the relationships among test anxiety levels, unit examination scores, and irregular multiple-choice error patterns (error clumping), as well as changes in these measures after the intervention. Results indicate significant, positive relationships between some measures of test anxiety and error clumping, as well as significant, negative relationships between test anxiety levels and student achievement. In addition, results show significant decreases in holistic measures of test anxiety among students with low anxiety levels, as well as decreases in Emotionality subscores of test anxiety among students with high levels of test anxiety. There were no significant changes over time in the Worry subscores of test anxiety. Suggestions for further research include further confirmation of the existence of error clumping, and its causal relationship with test anxiety.

Ethiopia's Grand Renaissance Dam: Implications for Downstream Riparian Countries

NASA Astrophysics Data System (ADS)

Zhang, Y.; Block, P. J.; Hammond, M.; King, A.

2013-12-01

Ethiopia has begun seriously developing their significant hydropower potential by launching construction of the Grand Ethiopian Renaissance Dam (GERD) on the Blue Nile River to facilitate local and regional growth. Although this has required substantial planning on Ethiopia's part, no policy dictating the reservoir filling rate strategy has been publicly issued. This filling stage will have clear implications on downstream flows in Sudan and Egypt, complicated by evaporative losses, climate variability, and climate change. In this study, various filling policies and future climate states are simultaneously explored to infer potential streamflow reductions at Lake Nasser, providing regional decision-makers with a set of plausible, justifiable, and comparable outcomes. Schematic of the model framework Box plots of 2017-2032 percent change in annual average streamflow at Lake Nasser for each filling policy constructed from the 100 time-series and weighted precipitation changes. All values are relative to the no dam policy and no changes to future precipitation.

Prevalence and prognostic value of echocardiographic screening for rheumatic heart disease

PubMed Central

Kotit, Susy; Said, Karim; ElFaramawy, Amr; Mahmoud, Hani; Phillips, David I W; Yacoub, Magdi H

2017-01-01

Objective Rheumatic heart disease (RHD) remains a major health problem in many low-income and middle-income countries. The use of echocardiographic imaging suggests that subclinical disease is far more widespread than previously appreciated, but little is known as to how these mild forms of RHD progress. We have determined the prevalence of subclinical RHD in a large group of schoolchildren in Aswan, Egypt and have evaluated its subsequent progression. Methods Echocardiographic screening was performed on 3062 randomly selected schoolchildren, aged 5–15 years, in Aswan, Egypt. Follow-up of children with a definite or borderline diagnosis of RHD was carried out 48–60 months later to determine how the valvular abnormalities altered and to evaluate the factors influencing progression. Results Sixty children were initially diagnosed with definite RHD (19.6 per 1000 children) and 35 with borderline disease (11.4 per 1000); most had mitral valve disease. Of the 72 children followed up progression was documented in 14 children (19.4%) and regression in 30 (41.7%) children. Boys had lower rates of progression while older children had lower rates of regression. Functional defects of the valve even in the presence of structural features were associated with lower rates of progression and higher rates of regression than structural changes. Conclusions RHD has a high prevalence in Egypt. Although a high proportion of the abnormalities originally detected persisted at follow-up, both progression and regression of valve lesions were demonstrated. PMID:29344370

Earth Observations taken by the Expedition 10 crew

NASA Image and Video Library

2005-01-23

ISS010-E-14618 (23 January 2005) --- Egypt's Lake Nasser, centered roughly at 22.64 degrees north latitude and 32.45 degrees east longitude, was captured with an electronic still camera by the Expedition 10 crew onboard the International Space Station. Sunglint on the lake makes it more easily visible.

A New Approach to Structural Reliability in Fatigue Failure

DTIC Science & Technology

1998-03-01

6. AUTHOR(S) Dr. Sia Nemat-Nasser (PI) Dr. Joseph Zarka 7. PERFORMING ORGANIZATION NAMES(S) AND ADDRESS(ES) 8. PERFORMING ORGANIZATION UniveBity of...their own problems. IV PUBLICATIONS Huang, J., J. Zarka and P. Navidi, "A New Approach in Relaibility of Welded Structures," Proceedings of the ASCE

Quality-based Multimodal Classification Using Tree-Structured Sparsity

DTIC Science & Technology

2014-03-08

Pennsylvania State University soheil@psu.edu Asok Ray Pennsylvania State University axr2@psu.edu@psu.edu Nasser M. Nasrabadi Army Research Laboratory...clustering for on- line fault detection and isolation. Applied Intelligence, 35(2):269–284, 2011. 4 [2] S. Bahrampour, A. Ray , S. Sarkar, T. Damarla, and N

An Assessment of the New York State Enhanced Security Guard Training Legislation and Its Efficacy on Security Officer Preparedness

DTIC Science & Technology

2011-12-01

ACKNOWLEDGMENTS I would like to begin by thanking my beautiful wife for her support during this program. I could not have completed this journey had it not...also pointed to the web writings of al Qaeda blogger Abu Suleiman Al-Nasser, who recently wrote, “Rush my Muslim brothers to targeting financial sites

Variation of Static-PPP Positioning Accuracy Using GPS-Single Frequency Observations (Aswan, Egypt)

NASA Astrophysics Data System (ADS)

Farah, Ashraf

2017-06-01

Precise Point Positioning (PPP) is a technique used for position computation with a high accuracy using only one GNSS receiver. It depends on highly accurate satellite position and clock data rather than broadcast ephemeries. PPP precision varies based on positioning technique (static or kinematic), observations type (single or dual frequency) and the duration of collected observations. PPP-(dual frequency receivers) offers comparable accuracy to differential GPS. PPP-single frequency receivers has many applications such as infrastructure, hydrography and precision agriculture. PPP using low cost GPS single-frequency receivers is an area of great interest for millions of users in developing countries such as Egypt. This research presents a study for the variability of single frequency static GPS-PPP precision based on different observation durations.

Swahili: Book III.

ERIC Educational Resources Information Center

Mwalozi, D. Chilyalya

This text of instructional materials, designed for the third level of a course in Swahili, contains 12 lessons with exercises for the student. Topics of the chapters include: (1) "Utabibu Hospitalini," (2) "Waifunga Ndoa Kanisani," (3) "Kutambua Saa," (4) "Kupiga Kambi," (5) "Mgema," (6) "Maisha ya Rais Nasser," (7) "Uhuru na Kazi," (8) "Mkonge,…

The Muslim Brotherhood in Egypt: Pursuing Moderation Within an Authoritarian Environment

DTIC Science & Technology

2011-06-01

17  b.  External Political, Cultural , and Social Influences ..............20...state’s comprehensive repression of the organization. The followers of the Muslim Brotherhood attributed the cultural , economic, and social grievances...Egypt has steadily lost cultural and political influence as a leading Arab state since the end of the Nasser era, national developments might still

Draft Genome Sequences of Six Multidrug-Resistant Clinical Strains of Acinetobacter baumannii, Isolated at Two Major Hospitals in Kuwait.

PubMed

Nasser, Kother; Mustafa, Abu Salim; Khan, Mohd Wasif; Purohit, Prashant; Al-Obaid, Inaam; Dhar, Rita; Al-Fouzan, Wadha

2018-04-19

Acinetobacter baumannii is an important opportunistic pathogen in global health care settings. Its dissemination and multidrug resistance pose an issue with treatment and outbreak control. Here, we present draft genome assemblies of six multidrug-resistant clinical strains of A. baumannii isolated from patients admitted to one of two major hospitals in Kuwait. Copyright © 2018 Nasser et al.

75 FR 2920 - In the Matter of the Designation of Nasir al-Wahishi, Also Known as Abu Basir, Also Known as Abu...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-01-19

..., Also Known as Abu Basir, Also Known as Abu Basir Nasir al-Wahishi, Also Known as Naser Abdel Karim al-Wahishi, Also Known as Nasir Abd al-Karim al- Wuhayshi, Also Known as Abu Basir Nasir al-Wuhayshi, Also Known as Nasser Abdul-karim Abdullah al-Wouhichi, Also Known as Abu Baseer al- Wehaishi, Also Known as...

Tile survey seen during EVA 3

NASA Image and Video Library

2005-08-03

S114-E-6396 (3 August 2005) --- Space Shuttle Discovery’s underside thermal protection tiles are featured in this image photographed by astronaut Stephen K. Robinson, STS-114 mission specialist, during the mission’s third session of extravehicular activities (EVA). Lake Nasser along the Nile River, Egypt is visible near Discovery’s starboard wing.

Microearthquake studies in Egypt carried out by the geological survey of Egypt

NASA Astrophysics Data System (ADS)

Boulos, Fouad K.; Morgan, Paul; Toppozada, Tousson R.

1987-07-01

Extensive microearthquake studies have been conducted in Egypt as a joint project between scientists from the Egyptian Geological Survey and Mining Authority (EGSMA) and U.S. scientists. At this stage, a great part of the data has been analyzed and two intensively active areas have been located: one in the Abu Dabbab area of the Eastern Desert, the second at the mouth of the Gulf of Suez near Gubal Island (Daggett et al., 1980). Both sites have been reported to be the epicenters of large earthquakes in 1955 and 1969, respectively. A few scattered earthquakes have also been located in the northern part of the Red Sea, some of which lie along its median axis (Daggett et al., 1986) adding to evidence for the medial opening of the northern Red Sea. After the occurrence of an earthquake (M = 5.5) in the Aswan region on 14 November 1981, continuous recording of the many aftershocks was carried out by EGSMA for about seven months from December 1981 to July 1982, when the temporary network was replaced by a network of telemetered seismographs installed and operated by Helwan Institute of Astronomy and Geophysics in cooperation with scientists from Lamont and Doherty Geological Observatory (LDGO). The majority of epicenters are concentrated in the vicinity of G. Marawa about 65 km upstream of Aswan Dam, along the E-W Kalabsha fault. The observed focal mechanism is consistent with a right-lateral strike-slip motion on the Kalabsha fault. Analysis of Aswan microearthquakes has been done by EGSMA in cooperation with scientists from California Division of Mines and Geology (CDMG).

[Women's participation in the Egyptian economy: trends and evolution].

PubMed

Khouri-dagher, N

1985-01-01

Changes in female participation in Egypt's monetary economy in response to the political, economic, and social transformations underway in the country over the past few decades are traced. Official statistics are difficult to interpret because of changing definitions of activities from 1 census or other statistical source to another and because such statistics consistently underestimate true female activity rates by a wide margin. Because much of the work done by Egyptian women is clandestine and sporadic and is not even viewed by them as "work", it would be very difficult to supply an estimate of the number of women economically active, but trends over the past several years can be discerned. Economic participation of women was uncommon when Nasser assumed power in 1952. Several measures taken by his administration were intended to promote female participation, and the system guaranteeing a public sector job to every person earning the baccalaureate was responsible for a dramatic increase in the number and percentage of women in public administration. The number of women working in industry increased during the years of Nasser's rule, the average age of working women increased significantly as women retained their jobs after marriage, and public approval of working women increased, but uneducated women from the poorer classes had greater difficulty in finding employment through regular channels. The new policies of Sadat, despite their fundamental opposition to Nasser's orientations, accentuated the trends already underway. Economic growth was accompanied by serious inflation and economic pressure on households, the "Opening to the West" offered new models of consumption and created new needs, the massive emigration to rich neighboring Arab countries created labor shortages, and the encouragement of emigration and free enterprise spawned a vast movement of social restructuring. The Sadat years also saw increasing difficulty in finding gainful employment for the

Gidzenko in front of flight deck windows

NASA Image and Video Library

2001-03-12

STS102-E-5138 (12 March 2001) --- Cosmonaut Yuri P. Gidzenko, now a member of the STS-102 crew, on Discovery's flight deck. Lake Nasser, in Egypt, can be seen through the overhead flight deck window in the background. Gidzenko, representing Rosaviakosmos, had been onboard the International Space Station (ISS) since early November 2000. The photograph was taken with a digital still camera.

Multimodal Task-Driven Dictionary Learning for Image Classification

DTIC Science & Technology

2015-12-18

1 Multimodal Task-Driven Dictionary Learning for Image Classification Soheil Bahrampour, Student Member, IEEE, Nasser M. Nasrabadi, Fellow, IEEE...Asok Ray, Fellow, IEEE, and W. Kenneth Jenkins, Life Fellow, IEEE Abstract— Dictionary learning algorithms have been suc- cessfully used for both...reconstructive and discriminative tasks, where an input signal is represented with a sparse linear combination of dictionary atoms. While these methods are

Hazard estimation deduced from GPS and seismic data of Egypt

NASA Astrophysics Data System (ADS)

Sayed Mohamed, Abdel-Monem

Egypt rapidly growing development is accompanied by increasing levels of standard living particular in its urban areas. However, there is a limited experience in quantifying the sources of risk management in Egypt and in designing efficient strategies to keep away serious impacts of earthquakes. From the historical point of view and recent instrumental records, there are some seismo-active regions in Egypt, where some significant earthquakes had occurred in different places. The special tectonic features in Egypt: Aswan, Greater Cairo, Red Sea and Sinai Peninsula regions are the territories of a high seismic risk, which have to be monitored by up-to date technologies. The investigations of the seismic events and interpretations led to evaluate the seismic hazard for disaster prevention and for the safety of the dense populated regions and the vital national projects as the High Dam. In addition to the monitoring of the recent crustal movements, the most powerful technique of satellite geodesy GPS are used where geodetic networks are covering such seismo-active regions. The results from the data sets are compared and combined in order to determine the main characteristics of the deformation and hazard estimation for specified regions. The final compiled output from the seismological and geodetic analysis threw lights upon the geodynamical regime of these seismo-active regions and put Aswan and Greater Cairo under the lowest class according to horizontal crustal strains classifications. This work will serve a basis for the development of so-called catastrophic models and can be further used for catastrophic risk management. Also, this work is trying to evaluate risk of large catastrophic losses within the important regions including the High Dam, strategic buildings and archeological sites. Studies on possible scenarios of earthquakes and losses are a critical issue for decision making in insurance as a part of mitigation measures.

Using the Global Navigation Satellite System (GNSS) data for Hazard Estimation in Some Active Regions in Egypt

NASA Astrophysics Data System (ADS)

Sayed Mohamed, Abdel-Monem

2016-07-01

Egypt rapidly growing development is accompanied by increasing levels of standard living particular in its urban areas. However, there is a limited experience in quantifying the sources of risk management in Egypt and in designing efficient strategies to keep away serious impacts of earthquakes. From the historical point of view and recent instrumental records, there are some seismo-active regions in Egypt, where some significant earthquakes had occurred in different places. The special tectonic features in Egypt: Aswan, Greater Cairo, Red Sea and Sinai Peninsula regions are the territories of a high seismic risk, which have to be monitored by up-to date technologies. The investigations of the seismic events and interpretations led to evaluate the seismic hazard for disaster prevention and for the safety of the dense populated regions and the vital national projects as the High Dam. In addition to the monitoring of the recent crustal movements, the most powerful technique of satellite geodesy GNSS are used where geodetic networks are covering such seismo-active regions. The results from the data sets are compared and combined in order to determine the main characteristics of the deformation and hazard estimation for specified regions. The final compiled output from the seismological and geodetic analysis threw lights upon the geodynamical regime of these seismo-active regions and put Aswan and Greater Cairo under the lowest class according to horizontal crustal strains classifications. This work will serve a basis for the development of so-called catastrophic models and can be further used for catastrophic risk management. Also, this work is trying to evaluate risk of large catastrophic losses within the important regions including the High Dam, strategic buildings and archeological sites. Studies on possible scenarios of earthquakes and losses are a critical issue for decision making in insurance as a part of mitigation measures.

Modeling Stakeholder Decision Logic: A Case Study of Lebanese Hezbollah

DTIC Science & Technology

2010-06-01

60 d. U.S. and the Iranian Oil Crisis..............................................62 e. U.S. and Egypt: Egyptian Revolution...backdrop, would frame and build toward the next conflict (Harms 2008). In 1956, Egyptian leader Gamul Abdul Nasser defiantly decided to nationalize...violence should precede diplomacy and politics” (Harms 108). 5 The PLO was founded in May 1964 and came under the control of Egyptian leader Gamul

MISR Views the Middle East

NASA Technical Reports Server (NTRS)

2000-01-01

This image, generated using 16 orbits of MISR data collected between August 16 and August 30, 2000, takes us to the cradle of many civilizations. The data are from the 60-degree aftward-viewing camera. Because the individual orbit swaths are only 400 kilometers wide, they were 'mosaiced' together to form this composite picture, which covers about 2700 kilometers from west to east and 1750 kilometers from north to south. A few discontinuities are present in the mosaic, particularly near clouds, due to changes in the scene which occurred between dates when the individual orbit data were acquired.

At the northern tip of the Red Sea, the Gulf of Suez and the Gulf of Aqaba frame the sandy deserts and spectacular mountains of the Sinai Peninsula. The highest peaks are Gebel Katherina (Mountain of St. Catherine, 2637 meters) and Gebel Musa (Mountain of Moses, also known as Mount Sinai, 2285 meters). To the northeast, Israel and Jordan flank the Dead Sea, one of the saltiest inland water bodies in the world. At its northern edge is Qumran, where the ancient Scrolls were discovered; the city of Jerusalem lies about 30 kilometers to the west.

Several large rivers are prominent. Flowing southeastward through Iraq are the Tigris and Euphrates. The dark area between the two rivers, northwest of the Persian Gulf, is a very fertile region where fishing and farming are prevalent. Wending its way through eastern Egypt is the Nile. In the south is Lake Nasser and the Aswan Dam; continuing northward the Nile passes the Temple of Luxor as it sharply loops to the east. It then turns west and northward, eventually passing the capital city of Cairo, and finally spreading into a prominent delta as it empties into the Mediterranean Sea. The bright dot just west of the apex of the delta marks the location of the great Pyramids and Sphinx complexes on the Giza Plateau. On the coast, west of the delta, is the ancient city of Alexandria, Egypt's main seaport.

'MISR', as it turns

A New Perspective on Eratosthenes' Measurement of the Earth

ERIC Educational Resources Information Center

Brown, Ronald A.; Kumar, Alok

2011-01-01

Around 240 B.C., Eratosthenes made what is considered to be the most famous and accurate of the ancient measurements of the circumference of the Earth. It was accomplished by making "presumably simultaneous" measurements of the angles of the shadows cast by a vertical stick at Syene (today known as Aswan) and another at Alexandria, at noon on the…

Nile River, Lake Nasser, North Sudan and Lower Egypt

NASA Image and Video Library

1992-11-01

STS052-152-026 (22Oct-1 Nov 1992) --- Backdropped over eastern Egypt, the Canadian-built remote manipulator system (RMS) attached to NASA's Earth-orbiting Space Shuttle Columbia displays a Canadian Space Agency (CSA) experiment. Materials Exposure in Low Earth Orbit (MELEO) is one of a number of Canadian experiments which flew aboard Columbia for the ten-day STS-52 mission. Principal investigator for the experiment is Dr. David G. Zimick of the CSA. Plastic and composite materials used on the external surfaces of spacecraft have been found to degrade in the harsh environment of space. Evidence suggests that this degradation is caused by interaction with atomic oxygen which induces damaging chemical and physical reactions. The result is a loss in mass, strength, stiffness and stability of size and shape. During the mission, MELEO exposed over 350 material specimens mounted on "witness plates" on the RMS arm. The specimen collection will be analyzed in the weeks following the mission. Typical spacecraft materials and new developments in protective measures against atomic oxygen were tested as part of the MELEO experiment.

Joint Sparsity-Based Robust Multimodal Biometrics Recognition

DTIC Science & Technology

2012-10-07

Nasrabadi, Rama Chellappa William Marsh Rice University Office of Sponsored Research William Marsh Rice University Houston, TX 77005 - REPORT...Shekhar1, Vishal M. Patel1, Nasser M. Nasrabadi2, and Rama Chellappa1 1 University of Maryland, College Park, USA 2 Army Research Lab, Adelphi, USA...authentication. Unfortunately these systems often have to deal with some of the following inevitable problems [1]: (a) Noisy data (b) Non- universality

America and the Containment of Arab Radical Nationalism: The Eisenhower Years

DTIC Science & Technology

1994-05-01

evolutionary process in the transformation and defense of the Arab East. 4 The emergence of Nasser and radical nationalism throughout the area required a... processes were evolutionary and optimistic. It would require decades to accomplish what had 10 taken centuries in their own societies. It also required...numerous foreign teohnicians and progressive political leaders, the latter being excluded from the political process by the conservatives. Many of these

Panel Session on the Future of Few-Body Physics

NASA Astrophysics Data System (ADS)

Bakker, Bernard L. G.; Carbonell, Jaume; Elster, Charlotte; Epelbaum, Evgeny; Kalantar-Nayestanaki, Nasser; Richard, Jean-Marc

2014-08-01

During the 22nd European Few-Body Conference, a session was devoted to a panel discussion on the future of few-body physics. The panel members were Charlotte Elster, Jaume Carbonell, Evgeny Epelbaum, Nasser Kalantar-Nayestanaki, and Jean-Marc Richard. The session was chaired by Ben Bakker. After presentations by the panel members, several topics were discussed with the audience. The conclusions of this discussion are presented in this paper.

Still a Special Relationship? The Significance of United States-United Kingdom Relations in the Twenty-First Century

DTIC Science & Technology

2011-12-01

Anglo - Saxon ally over Nasser and the canal.55 In 2010, in a speech at Chatham House, Liberal Democrat Nick Clegg suggested that “what...strategic culture, and as an expression of shared values and institutions the character of which is vital for those charged with service in an Anglo ...American context as well as NATO. 14. SUBJECT TERMS United Kingdom, United States, Special Relationship, Anglo - American Relations, Iraq, Afghanistan

Robust Multi Sensor Classification via Jointly Sparse Representation

DTIC Science & Technology

2016-03-14

rank, sensor network, dictionary learning REPORT DOCUMENTATION PAGE 11. SPONSOR/MONITOR’S REPORT NUMBER(S) 10. SPONSOR/MONITOR’S ACRONYM(S) ARO 8...with ultrafast laser pulses, Optics Express, (04 2015): 10521. doi: Xiaoxia Sun, Nasser M. Nasrabadi, Trac D. Tran. Task-Driven Dictionary Learning...in dictionary design, compressed sensors design, and optimization in sparse recovery also helps. We are able to advance the state of the art

Management of Egypt's Surface and Groundwater Resources: Present and Future

NASA Astrophysics Data System (ADS)

Sultan, M.; Ahmed, M.; Yan, E.; Milewski, A.; Mohamed, L.; Farag, A. Z. A.

2014-12-01

The River Nile is the main source of fresh water in Egypt. Most of Egypt's River Nile water (>85%) originates as precipitation over the Ethiopian highlands and is channeled by the Blue Nile. The construction (years: 2011 to 2017) of the Renaissance Dam (reservoir capacity: 70 x 109m3) on the Blue Nile poses an extreme threat to Egypt's population. If the reservoir was to be filled in 7 years, Egypt will lose (during each of 7 years following dam completion) a minimum of 15 x 109m3 of its annual allocation (55 x 109m3) to reservoir filling (10 x 109m3), evaporation (3.5 x 109m3), and infiltration (1.5 x 109m3). Three solutions are proposed: Solution I takes advantage of the cyclicity of Nile floods and is based on findings from a calibrated (against temporal head data) unconfined 2-dimensional transient groundwater flow model for Lake Nasser and surroundings and a calibrated (against lake levels) surface water model. Models show with time: (1) losses to infiltration will decrease (1975-193: 58.4 109m3; 1993-2001: 43.6 x 109m3) due to silting of Lake bottom and encroachment of excess Lake Nasser water will increase (e.g., 1975-1993: none; 1993-2001: 17 x 109m3). We propose to develop sustainable agricultural in the Western Desert: (1) In high flood years, excess Lake Nasser water (e.g., 1993-2001: 17 x 109m3) is channeled across the plateau bounding (from west) the River Nile valley to artificially recharge the Nubian Sandstone Aquifer System (NSAS) that crops out west of the plateau and, (2) in low flood years, we extract the recharged groundwater. Solution II calls on mining the NSAS at reasonable rates. Using temporal (January 2003 - September 2012) Gravity Recovery and Climate Experiment (GRACE) data we estimate the annual depletion rates at 2 x 109m3 due to artificial extraction (1.5 x 109m3) and natural discharge (0.5 x 109m3). Assuming current GRACE depletion rates, the recoverable groundwater (5,180 x 109m3) will last for 2500 years; if we were to quadruple

Geoelectrical contribution for delineation the groundwater potential and subsurface structures on Tushka Area, Egypt

NASA Astrophysics Data System (ADS)

Abd El-Gawad, A. M. S.; Kotb, Adel D. M.; Hussien, Galal H. G.

2017-12-01

Tushka area represents the South East Western Desert, Egypt. its contain many drilled wells which have many problems during use, so the present study aims at identify the aquifer conditions and its relation with surface water and subsurface structure in addition to determine the aquifer thickness by using the basement relief from previous work, then assess the current situation of the drilled water wells. Geoelectrical data were measured, processed and interpreted in one, two and three dimensions using special Equipments and software. The interpretation results demonstrated that two types of groundwater aquifers (confined and unconfined) are present in the study area. The confined aquifer is located at the south of Khor Tushka and the unconfined aquifer is found in the north of Khor Tushka, where the last one is charged from Lake Nasser and Khor Tushka. The groundwater aquifers thicknesses are up to 440 m and the area is affected by normal faults of NW-SE and NE-SW trends. The study showed that there is no connection between the confined aquifer and the shallow overlaying aquifer. The confined aquifer is charged partially from the lake Nasser and Khor Tushka through specific areas under the capping layers of Nubian sandstone filled with hydrothermal solution and shale.

Performance Comparison of Feature Extraction Algorithms for Target Detection and Classification

DTIC Science & Technology

2013-01-01

Detection and Classification⋆ Soheil Bahrampour1 Asok Ray2 Soumalya Sarkar2 Thyagaraju Damarla3 Nasser M. Nasrabadi3 Keywords: Feature Extraction...USA email:soheil@psu.edu 2A. Ray and S. Sarkar are with the Department of Mechanical Engineering, Pennsylvania State University, University Park, PA...no. 1, pp. 22–29, 2001. [5] G. Mallapragada, A. Ray , and X. Jin, “Symbolic dynamic filtering and language measure for behavior identification of mobile

Use of B-Spline in the Finite Element Analysis: Comparison with ANCF Geometry

DTIC Science & Technology

2011-02-04

Beam Elements”, Multibody System Dynamics , Vol. 20 (1), pp. 1-28. 7. Hamed, A.M., Shabana, A.A., Jayakumar , P., and Letherwood, M.D., 2011 “Non...West Taylor Street Chicago, Illinois 60607 Paramsothy Jayakumar Michael D. Letherwood U.S. Army RDECOM-TARDEC 6501 E. 11 Mile Road Warren...Ashraf Hamed; Abdel - Nasser Mohamed; Paramsothy Jayakumar ; Michael Letherwood 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7

Hemolysis and Mediterranean G6PD mutation (c.563 C>T) and c.1311 C>T polymorphism among Palestinians at Gaza Strip.

PubMed

Sirdah, Mahmoud; Reading, N Scott; Perkins, Sherrie L; Shubair, Mohammad; Aboud, Lina; Prchal, Josef T

2012-04-15

The G6PD c.563 C>T deficient mutation is endemic among Mediterranean populations but its clinical significance is not well delineated. We set up to estimate the proportion of G6PD deficient children presenting with hemolytic anemia at Al Nasser Pediatric Hospital at Gaza Strip, Palestine. We then established the prevalence of c.563T Mediterranean mutation and its linkage to c.1311 C>T polymorphism in this population. G6PD deficiency was identified in children presenting with hemolytic anemia at Al Nasser Pediatric Hospital by spectrophotometric measurement of G6PD activity. G6PD exon 6 and exon 11 were amplified from genomic DNA and evaluated for c.563T mutation by sequencing and the c.1311T polymorphism by restriction fragment analysis. Seventy X-chromosomes (60 males and 5 females) from G6PD deficient patients and 40 X-chromosomes from a control group known to be not G6PD deficient were tested. Over 80% of these children presenting with hemolytic anemia were G6PD deficient and 34% of these had the Mediterranean G6PD deficient variant. The allelic frequencies of Mediterranean c.563T and c.1311T polymorphisms among G6PD deficient patients were 0.33 and 0.38 respectively. The c.1311T polymorphism was linked in 95.2% of patients with the Mediterranean mutation, an allele frequency of 0.87, compared to the control non-G6PD deficient group with an allele frequency of 0.18. We conclude that G6PD deficiency accounts for majority of hemolytic anemia encountered in Gaza children treated at Al Nasser Pediatric Hospital Emergency department. The Mediterranean mutation c.563T, while not accounting for a majority of G6PD deficiency, is common among G6PD deficient Gaza Strip Palestinians and is frequently, but not always, linked to the c.1311T polymorphism. This work provides a foundation for the population screening of Palestinians for G6PD deficiency and for investigations of ancestral origin of the Mediterranean variant in world populations. Copyright © 2012 Elsevier Inc

NRIAG's Effort to Mitigate Earthquake Disasters in Egypt Using GPS and Seismic Data

NASA Astrophysics Data System (ADS)

Mahmoud, Salah

It has been estimated that, during historical time more than 50 million people have lost their lives in earthquakes during ground shaking, such as soil amplification and/or liquefaction, landslides and tsunamis or its immediate aftereffects, as fires. The distribution of population takes generally no account of earthquake risk, at least on a large scale. An earthquake may be large but not destructive, on the other hand, an earthquake may be destructive but not large. The absence of correlation is due to the fact that, great number of other factors entering into consideration: first of all, the location of the earthquake in relation to populated areas, also soil conditions and building constructions. Soil liquefaction has been identified as the underlying phenomenon for many ground failures, settlements and lateral spreads, which are a major cause of damage to soil structures and building foundations in many events. Egypt is suffered a numerous of destructive earthquakes as well as Kalabsha earthquake (1981, Mag 5.4) near Aswan city and the High dam, Dahshour earthquake (1992, Mag 5.9) near Cairo city and Aqaba earthquake (1995, Mag 7.2). As the category of earthquake damage includes all the phenomena related to the direct and indirect damages, the Egyptian authorities do a great effort to mitigate the earthquake disasters. The seismicity especially at the zones of high activity is investigated in details in order to obtain the active source zones not only by the Egyptian National Seismic Network (ENSN) but also by the local seismic networks at, Aswan, Hurghada, Aqaba, Abu Dabbab and Dabbaa. On the other hand the soil condition, soil amplification, soil structure interaction, liquefaction and seismic hazard are carried out in particular the urbanized areas and the region near the source zones. All these parameters are integrated to obtain the Egyptian building code which is valid to construct buildings resist damages and consequently mitigate the earthquake

Sequential Imaging of Earth by Astronauts: 50 Years of Global Change

NASA Technical Reports Server (NTRS)

Evans, Cynthia A.

2009-01-01

For nearly 50 years, astronauts have collected sequential imagery of the Earth. In fact, the collection of astronaut photography comprises one of the earliest sets of data (1961 to present) available to scientists to study the regional context of the Earth s surface and how it changes. While today s availability of global high resolution satellite imagery enables anyone with an internet connection to examine specific features on the Earth s surface with a regional context, historical satellite imagery adds another dimension (time) that provides researchers and students insight about the features and processes of a region. For example, one of the geographic areas with the longest length of record contained within the astronaut photography database is the lower Nile River. The database contains images that document the flooding of Lake Nasser (an analog to today s flooding behind China s Three Gorges Dam), the changing levels of Lake Nasser s water with multiyear cycles of flood and drought, the recent flooding and drying of the Toshka Lakes, as well as urban growth, changes in agriculture and coastal subsidence. The imagery database allows investigations using different time scales (hours to decades) and spatial scales (resolutions and fields of view) as variables. To continue the imagery collection, the astronauts on the International Space Station are trained to understand basic the Earth Sciences and look for and photograph major events such as tropical storms, landslides, and volcanic eruptions, and document landscapes undergoing change (e.g., coastal systems, cities, changing forest cover). We present examples of selected sequences of astronaut imagery that illustrate the interdependence of geological processes, climate cycles, human geography and development, and prompt additional questions about the underlying elements of change.

Restrictions of Non Associated Plastic Flow Laws Imposed by Thermodynamics and Uniqueness

DTIC Science & Technology

1986-05-20

which have been discussed by Kestin and Rice (1970). Valanis (1971c) and Nemat-Nasser (1975b). lie in the concepts of entropy and temperature. As a...to the concept of entropy. As an example. consider the case of a rigid heat conductor in thermal equilibrium. If heat is added to the conductor, the...entropy for such systems mathematically. Using the concept of partial integrability of Pfaffian forms, Valanis finds the temperature 0 = 0(j.eL) > 0 as

Structural Composites With Tuned EM Chirality

DTIC Science & Technology

2014-12-23

photonic   crystals .   Tammuz  Dubnov  (7/14  –  9/14)  –  Laboratory  Assistant  -­‐  assisted in the testing...AFRL-OSR-VA-TR-2015-0018 STRUCTURAL COMPOSITES WITH TUNED EM CHIRALITY Siavouche Nemat Nasser UNIVERSITY OF CALIFORNIA SAN DIEGO Final Report 12/23...REPORT Grant/Contract  Title:        STRUCTURAL  COMPOSITES  WITH  TUNED  EM   CHIRALITY     Grant  No.:

iss031e148455

NASA Image and Video Library

2012-06-21

ISS031-E-148455 (21 June 2012) --- Toshka Lakes in southern Egypt are featured in this image photographed by an Expedition 31 crew member on the International Space Station. The Toshka Lakes (center) were formed in the Sahara Desert of Egypt by water from the River Nile conveyed from Lake Nasser by a canal to the Toshka Depression. Flooding of the Toshka Depression had created the four main lakes with a maximum surface area in 2002 of approximately 1,450 square kilometers ? around 25.26 billion cubic meters of water. By 2006 the stored water was reduced by 50 per cent and by 2012 shows open water only in the lowest parts of the main western and eastern basins?representing a reduction in surface area to 307 square kilometers?nearly 80 per cent smaller than the 2002 surface area. Standing water is almost completely absent from the central basin. From space, astronauts documented the first lake?the easternmost one?in 1998. The lakes progressively grew in depressions to the west, the westernmost filling between 2000 and 2001. This image shows lines of center-point agricultural fields near the east-basin lake nearest Lake Nasser. Sunglint on the western lake makes the water surface appear both light and dark, depending on which parts of the surface were ruffled by the wind at the moment the image was taken.

Two species of tabanids (order: Diptera) in Aswan District, Egypt.

PubMed

Morsy, T A; Habib, K S

2001-08-01

Tabanus taeniola and Haematopota minuscula were trapped on camels and equines at daytime during summer of 2000. Many species of Tabanus and few species of Haematopota were reported before in Egypt. This paper stresses on the medical and veterinary importance of these vectors.

Nonlinear Waves in Rods

DTIC Science & Technology

1981-05-01

0 and P > 0 everywhere. This also implies from (17) that Www 1Wuu - Wu w1 > 0 so that necking instabilities have been ruled out (see Antman [12], pp... Antman , "Qualitative Theory of the Ordinary Differential Equa- tions of Nonlinear Elasticity," in Mechanics Today, V. 1, ed. S. Nemat- Nasser...the Propagation of Plastic Strain in a Cylindrical Rod," J. Mech. Phys. Sol., 13, 1965, pp. 55-68. 7. S. S. Antman , The Theory of Rods, Handbuch der

Reconstructing Ancient Egyptian Diet through Bone Elemental Analysis Using LIBS (Qubbet el Hawa Cemetery)

PubMed Central

Al-Khafif, Ghada Darwish; El-Banna, Rokia

2015-01-01

One of the most important advantages of LIBS that make it suitable for the analysis of archeological materials is that it is a quasi-nondestructive technique. Archeological mandibles excavated from Qubbet el Hawa Cemetery, Aswan, were subjected to elemental analysis in order to reconstruct the dietary patterns of the middle class of the Aswan population throughout three successive eras: the First Intermediate Period (FIP), the Middle Kingdom (MK), and the Second Intermediate Period (SIP). The bone Sr/Ca and Ba/Ca ratios were significantly correlated, so the Sr/Ca ratios are considered to represent the ante-mortem values. It was suggested that the significantly low FIP Sr/Ca compared to that of both the MK and the SIP was attributed to the consumption of unusual sorts of food and imported cereals during years of famine, while the MK Sr/Ca was considered to represent the amelioration of climatic, social, economic, and political conditions in this era of state socialism. The SIP Sr/Ca, which is nearly the same as that of the MK, was considered to be the reflection of the continuity of the individualism respect and state socialism and a reflection of agriculture conditions amelioration under the reign of the 17th Dynasty in Upper Egypt. PMID:26345727

Considerations in Managing the Fill Rate of the Grand Ethiopian Renaissance Dam Reservoir Using a System Dynamics Approach.

NASA Technical Reports Server (NTRS)

Keith, Bruce; Ford, David N.; Horton, Radley M.

2016-01-01

The purpose of this study is to evaluate simulated fill rate scenarios for the Grand Ethiopian Renaissance Dam while taking into account plausible climate change outcomes for the Nile River Basin. The region lacks a comprehensive equitable water resource management strategy, which creates regional security concerns and future possible conflicts. We employ climate estimates from 33 general circulation models within a system dynamics model as a step in moving toward a feasible regional water resource management strategy. We find that annual reservoir fill rates of 8-15% are capable of building hydroelectric capacity in Ethiopia while concurrently ensuring a minimum level of stream flow disruption into Egypt before 2039. Insofar as climate change estimates suggest a modest average increase in stream flow into the Aswan, climate changes through 2039 are unlikely to affect the fill rate policies. However, larger fill rates will have a more detrimental effect on stream flow into the Aswan, particularly beyond a policy of 15%. While this study demonstrates that a technical solution for reservoir fill rates is feasible, the corresponding policy challenge is political. Implementation of water resource management strategies in the Nile River Basin specifically and Africa generally will necessitate a national and regional willingness to cooperate.

Egypt- Old Ally, New Strategy

DTIC Science & Technology

2017-04-06

constitution, forming a government based on pan-Arab nationalism and not Islamic principles.5 In June 1956, the Aswan Dam project give rise to a new... form that statecraft takes in times of peace.13 A trinity of “hard, soft, and smart power” catchwords has entered the political lexicon in...7 Development The United States currently provides $200 million in Economic Support Funds to the state of Egypt in the form of

Satellite mapping of Nile Delta coastal changes

NASA Technical Reports Server (NTRS)

Blodget, H. W.; Taylor, P. T.; Roark, J. H.

1989-01-01

Multitemporal, multispectral scanner (MSS) landsat data have been used to monitor erosion and sedimentation along the Rosetta Promontory of the Nile Delta. These processes have accelerated significantly since the completion of the Aswan High Dam in 1964. Digital differencing of four MSS data sets, using standard algorithms, show that changes observed over a single year period generally occur as strings of single mixed pixels along the coast. Therefore, these can only be used qualitatively to indicate areas where changes occur. Areas of change recorded over a multi-year period are generally larger and thus identified by clusters of pixels; this reduces errors introduced by mixed pixels. Satellites provide a synoptic perspective utilizing data acquired at frequent time intervals. This permits multiple year monitoring of delta evolution on a regional scale.

JPRS Report, Near East & South Asia, Egypt

DTIC Science & Technology

1991-09-10

Aswan, Luxor, and are there. Everything moves backwards. There is a policy Giza have half the antiquities of the world. And there is of statements...think it is going to happen to us if we in the sarcophagus of Cheops in the Great Pyramid ; that quicken our pace towards reform, even though we made...crazy about the Pyramid and its ment; from a government that lives in a cemetery and secrets, crazy about Akhnaten and the Sphinx. If I were still

Efficacy of Commercial Mosquito Traps in Capturing Phlebotomine Sand Flies (Diptera: Psychodidae) in Egypt

DTIC Science & Technology

2010-01-01

forDiseaseControl andPrevention (CDC) light trap for efÞcacy in collecting phlebotomine sand ßies (Diptera: Psychodidae) in a small farming village in the...Prevention (CDC) light trap for ef?acy in collecting phlebotomine sand ?es (Diptera: Psychodidae) in a small farming village in the Nile River Valley 10 km...Testing was conducted in June, August, and September 2007, in Bahrif village, a farming com- munity of 500 people 10 km north of Aswan on the east

Up-to-date Probabilistic Earthquake Hazard Maps for Egypt

NASA Astrophysics Data System (ADS)

Gaber, Hanan; El-Hadidy, Mahmoud; Badawy, Ahmed

2018-04-01

An up-to-date earthquake hazard analysis has been performed in Egypt using a probabilistic seismic hazard approach. Through the current study, we use a complete and homogenous earthquake catalog covering the time period between 2200 BC and 2015 AD. Three seismotectonic models representing the seismic activity in and around Egypt are used. A logic-tree framework is applied to allow for the epistemic uncertainty in the declustering parameters, minimum magnitude, seismotectonic setting and ground-motion prediction equations. The hazard analysis is performed for a grid of 0.5° × 0.5° in terms of types of rock site for the peak ground acceleration (PGA) and spectral acceleration at 0.2-, 0.5-, 1.0- and 2.0-s periods. The hazard is estimated for three return periods (72, 475 and 2475 years) corresponding to 50, 10 and 2% probability of exceedance in 50 years. The uniform hazard spectra for the cities of Cairo, Alexandria, Aswan and Nuwbia are constructed. The hazard maps show that the highest ground acceleration values are expected in the northeastern part of Egypt around the Gulf of Aqaba (PGA up to 0.4 g for return period 475 years) and in south Egypt around the city of Aswan (PGA up to 0.2 g for return period 475 years). The Western Desert of Egypt is characterized by the lowest level of hazard (PGA lower than 0.1 g for return period 475 years).

Effect of urbanization on population structure in U.A.R.

PubMed

Husein, H M; Sarhan, A E

1970-06-01

Census data from Egypt in 1927, 1937, 1947, and 1960 indicate slow urbanization through 1937 and more rapid urbanization thereafter. There is a higher proportion of working age (15-44) people in urban areas and a higher proportion of males. Both fertility and mortality rates are higher in rural than in urban areas, but the rate of overall population growth is greater in urban areas. Figures from 4 recently industrialized urban areas (El-Mahalla, Kafr el-Dawar, Helwan, and Aswan) bear out the conclusions drawn from the general census figures.

GC-MS analysis of aroma of Medemia argun (mama-n-khanen or mama-n-xanin), an ancient Egyptian fruit palm.

PubMed

Hamed, Arafa I; Leonardi, Michele; Stochmal, Anna; Oleszek, Wieslaw; Pistelli, Luisa

2012-05-01

The fruits of the edible and medicinal Egyptian palm, Medemia argun, were collected from Aswan in Egypt and the essential oil (EO) from fruits and headspace (HS) of the seeds and fleshy mesocarps were analyzed by GC and GC-MS. Results obtained by GC-MS analysis indicated a high variability in the oil and in the headspace from seeds and mesocarps. Sesquiterpene derivatives were the main group of volatiles in the EO from fruits and in the HS from seeds (45.0 and 64.0%, respectively), while oxygenated hydrocarbon derivatives were the main constituents in the HS obtained from fleshy mesocarps (96.5%). The different chemical composition of the headspace obtained from the seeds and mesocarps of M. argun can be correlated with the different roles that the different constituents play in the prevention of dehydration of the fruits in the desert region from where the plant was collected.

Characteristics of the first stage of constructing the Hoabinh Dam in Vietnam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bogachenko, P.T.; Godunov, B.I.; Phunc Ne, T.

1985-06-01

As a result of an analysis of the data, investigations, and on-site observations at the Hoa-Binh Dam, Vietnam, the authors conclude: infilling of the rock mass with sand, successful for the Aswan dam, cannot be mechanically transferred to other dams; the possibility of using the energy of the river flow for removing low-quality soils in large amounts from the foundation of rock-fill dams by regulating the sequence of dumping the elements of the dam was confirmed in model investigations and successfully accomplished in the construction of the HoaBinh dam; at the site of the Hoa-Binh dam, observations of the dumpingmore » of the sand-gravel soil into water into a high shoulder did not reveal segregation of this soil, however, the data from investigations in a single borehole contradict the observations -- further on-site observation must therefore be made.« less

Microbiologic and Clinical Study of Acute Diarrhea in Children in Aswan, Egypt

DTIC Science & Technology

1989-01-01

protozoa and helminth eggs in feces. Am J Trop Med Hyg 4: 23-28, 1955. 12. EI-Saili A, Kamel M, El-Din AM, Zaghloul I, Podgore JK, Mansour NS, Mikhail I... Parasitic , bacterial and viral etiology of acute diarrhea in Egyptian children. Med J Cairo University 53: 373-379, 1985. 13. Azab ME, Khalil HM, Khalifa

Earth observations during Space Shuttle flight STS-26: Discovery's mission to earth - September 29-October 3, 1988

NASA Technical Reports Server (NTRS)

Wood, C. A.; Helfert, M. R.; Lulla, K. P.; Covey, R. O.

1989-01-01

During the late September-early October, 1988 flight of the Space Shuttle Discovery, astronauts took 1505 photographs of earth using handheld cameras. The resulting pictures provide an overview, not available from any other source, of dynamic environmental phenomena on five continents. The Discovery photographs show that: (1) atmospheric clarity has improved in the Northern Hemisphere, (2) widespread burning of natural vegetation throughout the Southern Hemisphere continues to generate immense smoke palls and extensive sedimentation in rivers and estuaries, and (3) although the drought in Africa was partially relieved by heavy rains in autumn, 1988, Lakes Chad and Nasser are at the lowest levels ever seen from space.

Safety of patient meals in 2 hospitals in Alexandria, Egypt before and after training of food handlers.

PubMed

El Derea, H; Salem, E; Fawzi, M; Abdel Azeem, M

2008-01-01

We assessed the food safety knowledge and food handling practices of 23 food handlers in 2 hospitals in Alexandria, Egypt [Gamal Abdel Nasser (GAN) and Medical Research Institute (MRI)] before and after a food safety training programme, and also the bacteriological quality of patient meals and kitchen equipment. There was a significant improvement in all knowledge-associated parameters except for personal hygiene in GAN. There was an improvement in the food safety practices in both hospitals. The bacteriological quality of most patient meals and food preparation surfaces and utensils improved after training. The bacteriological quality of patients' meals served in GAN was generally better than that in MRI.

Volatiles and primary metabolites profiling in two Hibiscus sabdariffa (roselle) cultivars via headspace SPME-GC-MS and chemometrics.

PubMed

Farag, Mohamed A; Rasheed, Dalia M; Kamal, Islam M

2015-12-01

Hibiscus sabdariffa (roselle) is a plant of considerable commercial importance worldwide as functional food due to its organic acids, mucilage, anthocyanins, macro and micro-nutrients content. Although Hibiscus flowers are emerging as very competitive targets for phytochemical studies, very little is known about their volatile composition and or aroma, such knowledge can be suspected to be relevant for understanding its olfactory and taste properties. To provide insight into Hibiscus flower aroma composition and for its future use in food and or pharmaceutical industry, volatile constituents from 2 cultivars grown in Egypt, viz. Aswan and Sudan-1 were profiled using solid-phase microextraction (SPME) coupled to GCMS. A total of 104 volatiles were identified with sugar and fatty acid derived volatiles amounting for the major volatile classes. To reveal for cultivar effect on volatile composition in an untargeted manner, multivariate data analysis was applied. Orthogonal projection to latent structures-discriminant analysis (OPLS-DA) revealed for 1-octen-3-ol versus furfural/acetic acid enrichment in Aswan and Sudan-1 cvs., respectively. Primary metabolites contributing to roselle taste and nutritional value viz. sugars and organic acids were profiled using GC-MS after silylation. The impact of probiotic bacteria on roselle infusion aroma profile was further assessed and revealed for the increase in furfural production with Lactobacillus plantarum inoculation and without affecting its anthocyanin content. This study provides the most complete map for volatiles, sugars and organic acids distribution in two Hibiscus flower cultivars and its fermented product. Copyright © 2015 Elsevier Ltd. All rights reserved.

The genus Macroocula Panfilov in Egypt, with two new species (Hymenoptera: Bradynobaenidae: Apterogyninae).

PubMed

Gadallah, Neveen S; Soliman, Ahmed M; Al-Shahat, Ahmed M; Hossni, Mohammed T

2015-09-16

The genus Macroocula Panfilov in Egypt is reviewed. Seven species were previously recorded from Egypt: M. magna (Invrea, 1965), M. mahunkai Argaman, 1994, M. morawitzi (Radoszkowski, 1888), M. nigriventris (Invrea, 1960), M. nitida (Bischoff, 1920), M. savignyi (Klug, 1829) and M. sinaica (Invrea, 1963). Macroocula brothersi Gadallah & Soliman, sp. nov. (Egypt, Wadi Shab, Red Sea) and M. salehi Gadallah & Soliman, sp. nov. (Egypt, Wadi Shaghab, Aswan) are described and illustrated. The subspecies M. nitida nitida (Bischoff, 1920) and M. nitida patrizii (Invrea, 1932) are raised to species level. An illustrated key and a faunistic list of Macroocula species are given.

Assessment of environmental impacts part one. Intervention analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hipel, Keith William; Lettenmaier, Dennis P.; McLeod, A. Ian

The use of intervention analysis as a statistical method of gauging the effects of environmental changes is discussed. The Box-Jenkins model, serves as the basis for the intervention analysis methodology. Environmental studies of the Aswan Dam, the South Saskatchewan River, and a forest fire near the Pipers Hole River, Canada, are included as case studies in which intervention analysis was employed. Methods of data collection for intervention analysis are found to have a significant impact on model reliability; effective data collection processes for the Box-Jenkins model are provided. (15 graphs, 27 references, 2 tables)

Payload bay and ODS after undocking with Mir

NASA Image and Video Library

1996-09-24

STS079-808-008 (16-26 Sept. 1996) --- In this 70mm frame from the space shuttle Atlantis, the Nile River wanders through the eastern Sahara Desert of Sudan and Egypt. In the foreground is a great bend of the Nile from north to south past the Fourth Cataract at Merowe (an ancient Sudanese dynastic capitol), then north past Dongola and the Third Cararact, to Lake Nasser in Egypt. Prominent sand streaks display a north-south alignment. North of the first great bend a thick dust storm completely obscures the land surface, near Merowe thinner dust creates a hazy look. In the distance the Red Sea stretches from Suez to southern Arabia.

Ocean-color remote sensing of the Nile delta shelf and SE Levantine basin and possible linkage to some mesoscale circulation features and Nile river run-off

NASA Astrophysics Data System (ADS)

Moufaddal, Wahid; Lavender, Samantha

To date, and despite the passage of more than 30 years since the launch of the first satellite based ocean-color sensor, no systematic study of the variability of chlorophyll in the Egyptian Mediterranean coast off the Nile delta has been undertaken using this kind of data. Meantime, available in-situ measurements on chlorophyll and other nutrient parameters along this coast are indeed very modest and scarce. The lack of data has in turn created a large gap in our knowledge on the biogeochemical characteristics of the coastal water and impacts of the Aswan High Dam and other land-use changes on the marine ecosystems and nutrient budget in the Nile delta shelf and the SE Mediterranean. The present study aims to fill part of this gap through application of ocean-color remote sensing and satellite retrieval of phytoplankton chlorophyll. For this purpose a 10-year (1997-2006) monthly satellite dataset from ESA Globcolour project (an ESA Data User Element project: http://www.globcolour.info) was retrieved and subjected to time-series analysis. Results of this analysis revealed that the oceanic and coastal parts off the Nile delta coast and SE Mediterranean manifest from time to time some of the most interesting and dynamical marine features including meso-scale gyres, coastal filaments, localized algal blooms and higher concentration of phytoplankton chlorophyll. These features together with certain physical pro-cesses and surface run-off from Nile mouthes and other land-based sources were found to exert pronounced effects on the nutrient supply and quality of the coastal and oceanic surface waters in this region. Results reveled also that there has been a general upward trend in concentration of surface chlorophyll during the 10-year period from 1997 to 2006 with a coincident rise of the coastal fisheries implying that improvement of nutrient supply is most likely responsible for this rise. Results confirmed also shift of the Nile phytoplankton bloom in space and time

Black and red granites in the Egyptian Antiquity Museum of Turin. A minero-petrographic and provenance study.

NASA Astrophysics Data System (ADS)

Serra, M.; Borghi, A.; Vaggelli, G.; D'Amicone, E.; Vigna, L.

2009-04-01

materials used for two of the best known masterpieces of Egyptian art. As regards to red granites, it has been observed that most of the exposed sculptures were made of rocks closely akin to Aswan granite. Just in one case, the Ram headed sphinx (cat. 836), macroscopic differences in colour index, grain size and isoorientation of feldspar phenocrysts, suggested a different provenance of the source material and determined the choice of picking up a small fragment for minero-petrographic analysis. The sample collected from the sarcophagus of Nefertari (suppl. 5153) during the recent restoration of the sculpture, was analysed in order to test the accuracy of the results, as the provenance of the material used for its realization was already certain. Petrographic observations and chemical analysis were undertaken by a scanning electron microscope equipped with an energy-dispersive spectrometer. Minero-petrographic data primarily showed that all samples vary in composition from granite (red granites) to granodiorite and tonalite (black granites). The main sialic phases are represented by plagioclase (albite to oligoclase), alkali-feldspar (microcline) and quartz, while femic phases are amphibole (green horneblende) and biotite (Fe- to Mg-biotite), always coexisting in variable relative percentages. Minor amount of apatite (≈ 1 wt.%), magnetite, ilmenite, often associated to sphene, zircon, pyrite and allanite also occur. The identification of some compositional markers in all samples suggested a common provenance for all the rocks used for the sculptures. Thus, it was supposed that they could all have been quarried in the famous district of Aswan, well known at least since Dynastic period. This provenance hypothesis was confirmed by geological literature and archeological evidences, considering the relative proximity of Aswan quarries to Nile river and to the key centres of power in the New Kingdom. Therefore, several geological samples were collected in Aswan area, in order

Visualization of channels connecting cells in filamentous nitrogen-fixing cyanobacteria.

PubMed

Omairi-Nasser, Amin; Haselkorn, Robert; Austin, Jotham

2014-07-01

Cyanobacteria, formerly called blue-green algae, are abundant bacteria that carry out green plant photosynthesis, fixing CO2 and generating O2. Many species can also fix N2 when reduced nitrogen sources are scarce. Many studies imply the existence of intracellular communicating channels in filamentous cyanobacteria, in particular, the nitrogen-fixing species. In a species such as Anabaena, growth in nitrogen-depleted medium, in which ∼10% of the cells differentiate into anaerobic factories for nitrogen fixation (heterocysts), requires the transport of amino acids from heterocysts to vegetative cells, and reciprocally, the transport of sugar from vegetative cells to heterocysts. Convincing physical evidence for such channels has been slim. Using improved preservation of structure by high-pressure rapid freezing of samples for electron microscopy, coupled with high-resolution 3D tomography, it has been possible to visualize and measure the dimensions of channels that breach the peptidoglycan between vegetative cells and between heterocysts and vegetative cells. The channels appear to be straight tubes, 21 nm long and 14 nm in diameter for the latter and 12 nm long and 12 nm in diameter for the former.-Omairi-Nasser, A., Haselkorn, R., Austin, J. II. Visualization of channels connecting cells in filamentous nitrogen-fixing cyanobacteria. © FASEB.

Comparative analysis of Hibiscus sabdariffa (roselle) hot and cold extracts in respect to their potential for α-glucosidase inhibition.

PubMed

Rasheed, Dalia M; Porzel, Andrea; Frolov, Andrei; El Seedi, Hesham R; Wessjohann, Ludger A; Farag, Mohamed A

2018-06-01

Roselle (Hibiscus sabdariffa) is a functional food with potential health benefits, consumed either as hot or cold beverage. To ensure quality control of its various products, accurate measurement of active metabolites is warranted. Herein, we propose a combination of ultra-high performance liquid chromatography-mass spectrometry (UHPLC-MS) and nuclear magnetic resonance (NMR) analytical platforms for the untargeted characterization of metabolites in two roselle cultivars, Aswan and Sudan-1. The analyses revealed 33 metabolites, including sugars, flavonoids, anthocyanins, phenolic and aliphatic organic acids. Their relative contents in cultivars were assessed via principle component analysis (PCA) and orthogonal projection to latent structures analysis (OPLS). Impact of the different extraction methods (decoction, infusion and maceration) was compared by quantitative 1 H NMR spectroscopy, revealing cold maceration to be optimal for preserving anthocyanins, whereas infusion was more suited for recovering organic acids. The metabolite pattern revealed by the different extraction methods was found in good correlation for their ability to inhibit α-glucosidase enzyme. Copyright © 2018 Elsevier Ltd. All rights reserved.

Earth observations taken during STS-102 flight

NASA Image and Video Library

2001-03-18

STS102-303-017 (8-21 March 2001)--- The STS-102 crew members used a 35mm camera on the flight deck of the Space Shuttle Discovery to record this image of the Aswan High Dam. The structure was completed in 1970 and is one of the largest earthen embankment dams in the world. It is 364 feet (111 meters) tall, 12,565 feet (3,830 meters) long and nearly 3,281 feet (1,000 meters) wide. When it was built the new reservoir required relocation of nearly 100,000 residents and some archaeological sites. Although the reservoir has benefited Egypt by providing power and controlling floods, according to NASA scientists, it has also had detrimental effects on the Nile system. Before the dam, an estimated 110 million tons of silt was deposited by the annual flood of the Nile, enriching agricultural lands and maintaining the land of the Nile delta. Now this sediment is trapped behind the dam, requiring artificial fertilization of agricultural lands and leading to erosion and saltwater intrusion where the Nile river meets the Mediterranean Sea.

Assessment of macroseismic intensity in the Nile basin, Egypt

NASA Astrophysics Data System (ADS)

Fergany, Elsayed

2018-01-01

This work intends to assess deterministic seismic hazard and risk analysis in terms of the maximum expected intensity map of the Egyptian Nile basin sector. Seismic source zone model of Egypt was delineated based on updated compatible earthquake catalog in 2015, focal mechanisms, and the common tectonic elements. Four effective seismic source zones were identified along the Nile basin. The observed macroseismic intensity data along the basin was used to develop intensity prediction equation defined in terms of moment magnitude. Expected maximum intensity map was proven based on the developed intensity prediction equation, identified effective seismic source zones, and maximum expected magnitude for each zone along the basin. The earthquake hazard and risk analysis was discussed and analyzed in view of the maximum expected moment magnitude and the maximum expected intensity values for each effective source zone. Moderate expected magnitudes are expected to put high risk at Cairo and Aswan regions. The results of this study could be a recommendation for the planners in charge to mitigate the seismic risk at these strategic zones of Egypt.

[Side Effects of Modernity : Dam Building, Health Care, and the Construction of Power in the Context of the Control of Schistosomiasis in Egypt in the 1960s and early 1970s].

PubMed

Brendel, Benjamin

2017-09-01

This article analyzes the modernization campaigns in Egypt in the 1960s and early 1970s. The regulation of the Nile by the Aswan High Dam and the resulting irrigation projects caused the rate of schistosomiasis infestation in the population to rise. The result was a discourse between experts from the global north and Egyptian elites about modernization, development aid, dam building and health care. The fight against schistosomiasis was like a cipher, which combined different power-laden concepts and arguments. This article will decode the cipher and allow a deeper look into the contemporary dimensions of power bound to this subject. The text is conceived around three thematic axes. The first deals with the discursive interplay of modernization, health and development aid in and for Egypt. The second focuses on far-reaching and long-standing arguments within an international expert discourse about these concepts. Finally, the third presents an exemplary case study of West German health and development aid for fighting schistosomiasis in the Egyptian Fayoum oasis.

Detection of large scale geomagnetic pulsations by MAGDAS-egypt stations during the solar minimum of the solar cycle 24

NASA Astrophysics Data System (ADS)

Fathy, Ibrahim

2016-07-01

This paper presents a statistical study of different types of large-scale geomagnetic pulsation (Pc3, Pc4, Pc5 and Pi2) detected simultaneously by two MAGDAS stations located at Fayum (Geo. Coordinates 29.18 N and 30.50 E) and Aswan (Geo. Coordinates 23.59 N and 32.51 E) in Egypt. The second order butter-worth band-pass filter has been used to filter and analyze the horizontal H-component of the geomagnetic field in one-second data. The data was collected during the solar minimum of the current solar cycle 24. We list the most energetic pulsations detected by the two stations instantaneously, in addition; the average amplitude of the pulsation signals was calculated.

Mitochondrial D-loop sequences reveal a mixture of endemism and immigration in Egyptian goat populations.

PubMed

Ahmed, Sahar; Grobler, Paul; Madisha, Thabang; Kotze, Antionette

2017-09-01

The mitochondrial D-loop region was used to investigate genetic diversity within and between populations of Egyptian goats, to elucidate processes that explain present patterns of diversity and differentiation and to characterize Egyptian goats relative to international breeds. A total of 120 animals from six populations were sampled. Results confirm the main trend from previous studies of mtDNA diversity in goats, with high levels of diversity within populations, but with a comparative lack of genetic structure supporting geographic distribution. Haplotype diversity varied in a narrow range whereas nucleotide diversity values were more informative in showing differences between populations. The majority of goats analyzed (93.2%) displayed haplotypes that group with Haplogroup A, the most common type found in global goat populations. The remaining animals grouped with the less common Haplogroup G. Population differentiation analysis showed some uniqueness in the Aswan and Sharkawi populations from the South and East of Egypt. Overall, the structure of the Egyptian goat population is characterized by a high degree of homogeneity among populations from the north-western coastal region, the Nile Delta and the upper and middle regions of the Nile valley, but with possible introgression of rarer haplotypes into populations at the southern and eastern extremities of the country.

The geological heritage of the Kurkur-Dungul area in southern Egypt

NASA Astrophysics Data System (ADS)

Sallam, Emad S.; Ponedelnik, Alena A.; Tiess, Günter; Yashalova, Natalia N.; Ruban, Dmitry A.

2018-01-01

The inventory of the geological heritage of Egypt is important for its efficient conservation and usage for the purposes of science, education, and tourism. The field investigations in the Kurkur-Dungul area in southern Egypt have permitted to identify several unique geological features. Their type, rank, relative abundance, and intrinsic diversity, as well as importance of the entire geological heritage of the study area are investigated. Seven geological heritage types are distinguished, namely stratigraphical, sedimentary, palaeogeographical, mineralogical, structural, geomorphological, and economical types. The rank of the features belonging to the listed types ranges from local to global, and the relative abundance and the intrinsic diversity range from low to high. The global rank is established for the sedimentary type, which is determined by the wide distribution of palaeospring tufa deposits. The high relative abundance and intrinsic diversity are established for the geomorphological type. The entire geological heritage of the Kurkur-Dungul area can be employed for diversification of the existing tourism programs offered at the tourist destination of Aswan, as well as for geotourism development. A geopark can be created in the Kurkur-Dungul area for the better exploitation of its geological heritage. The combined development of geological and industrial tourism seems to be possible.

Kinematic-PPP using Single/Dual Frequency Observations from (GPS, GLONASS and GPS/GLONASS) Constellations for Hydrography

NASA Astrophysics Data System (ADS)

Farah, Ashraf

2018-03-01

Global Positioning System (GPS) technology is ideally suited for inshore and offshore positioning because of its high accuracy and the short observation time required for a position fix. Precise point positioning (PPP) is a technique used for position computation with a high accuracy using a single GNSS receiver. It relies on highly accurate satellite position and clock data that can be acquired from different sources such as the International GNSS Service (IGS). PPP precision varies based on positioning technique (static or kinematic), observations type (single or dual frequency) and the duration of observations among other factors. PPP offers comparable accuracy to differential GPS with safe in cost and time. For many years, PPP users depended on GPS (American system) which considered the solely reliable system. GLONASS's contribution in PPP techniques was limited due to fail in maintaining full constellation. Yet, GLONASS limited observations could be integrated into GPS-based PPP to improve availability and precision. As GLONASS reached its full constellation early 2013, there is a wide interest in PPP systems based on GLONASS only and independent of GPS. This paper investigates the performance of kinematic PPP solution for the hydrographic applications in the Nile river (Aswan, Egypt) based on GPS, GLONASS and GPS/GLONASS constellations. The study investigates also the effect of using two different observation types; single-frequency and dual frequency observations from the tested constellations.

Earth observations taken from Space Shuttle Columbia during STS-80 mission

NASA Image and Video Library

1996-11-28

STS080-745-004 (19 Nov.-7 Dec. 1996) --- A view to the west showing Asia in the foreground and Africa in the background, as photographed by the space shuttle Columbia crewmembers. The Mediterranean Sea is to the upper right and the Red Sea to the lower left (holding photograph with NASA numbers on left). Sinai Peninsula is between the two with the Gulf of Suez above and the Gulf of Aqaba below. The Suez Canal connects the Gulf of Suez with the Mediterranean Sea. The triangular shaped dark area beyond is the Nile River Delta. The thin green fertile valley of the Nile crosses the photograph from a point at Cairo (near dark triangle area) past the great bend at Luxor with Thebes and the Valley of the Kings, and on the left into the Nubian Desert with the Aswan High Dam at the very left edge of the photograph. To the horizon is the Western Desert of Egypt and Libya. The foreground is the northwest portion of Saudi Arabia, an area known as the Hejaz with the southern portions of Israel and Jordan to the lower right.

Population genetics analysis of Phlebotomus papatasi sand flies from Egypt and Jordan based on mitochondrial cytochrome b haplotypes.

PubMed

Flanley, Catherine M; Ramalho-Ortigao, Marcelo; Coutinho-Abreu, Iliano V; Mukbel, Rami; Hanafi, Hanafi A; El-Hossary, Shabaan S; Fawaz, Emad El-Din Y; Hoel, David F; Bray, Alexander W; Stayback, Gwen; Shoue, Douglas A; Kamhawi, Shaden; Karakuş, Mehmet; Jaouadi, Kaouther; Yaghoobie-Ershadi, Mohammad Reza; Krüger, Andreas; Amro, Ahmad; Kenawy, Mohamed Amin; Dokhan, Mostafa Ramadhan; Warburg, Alon; Hamarsheh, Omar; McDowell, Mary Ann

2018-03-27

Phlebotomus papatasi sand flies are major vectors of Leishmania major and phlebovirus infection in North Africa and across the Middle East to the Indian subcontinent. Population genetics is a valuable tool in understanding the level of genetic variability present in vector populations, vector competence, and the development of novel control strategies. This study investigated the genetic differentiation between P. papatasi populations in Egypt and Jordan that inhabit distinct ecotopes and compared this structure to P. papatasi populations from a broader geographical range. A 461 base pair (bp) fragment from the mtDNA cytochrome b (cyt b) gene was PCR amplified and sequenced from 116 individual female sand flies from Aswan and North Sinai, Egypt, as well as Swaimeh and Malka, Jordan. Haplotypes were identified and used to generate a median-joining network, F ST values and isolation-by-distance were also evaluated. Additional sand fly individuals from Afghanistan, Iran, Israel, Jordan, Libya, Tunisia and Turkey were included as well as previously published haplotypes to provide a geographically broad genetic variation analysis. Thirteen haplotypes displaying nine variant sites were identified from P. papatasi collected in Egypt and Jordan. No private haplotypes were identified from samples in North Sinai, Egypt, two were observed in Aswan, Egypt, four from Swaimeh, Jordan and two in Malka, Jordan. The Jordan populations clustered separately from the Egypt populations and produced more private haplotypes than those from Egypt. Pairwise F ST values fall in the range 0.024-0.648. The clustering patterns and pairwise F ST values indicate a strong differentiation between Egyptian and Jordanian populations, although this population structure is not due to isolation-by-distance. Other factors, such as environmental influences and the genetic variability in the circulating Le. major parasites, could possibly contribute to this heterogeneity. The present study aligns with

Earth observations during Space Shuttle flight STS 50 - Columbia's mission to planet earth (June 25-July 9, 1992)

NASA Technical Reports Server (NTRS)

Lulla, Kamlesh P.; Helfert, Michael; Amsbury, David; Pitts, David; Evans, Cynthia; Wilkinson, Justin; Helms, David; Chambers, Mark; Brumbaugh, Fred; Richards, Richard N.

1993-01-01

A review of the imagery acquired during the STS 50 mission of the Space Shuttle is presented. The earth viewing photography from this flight includes photos of dust plumes over several portions of the Red Sea, Arabian Sea, Persian Gulf, the Mediterranean Sea, and the Atlantic Ocean. Over land, prominent dust plumes were seen over Iraq, North Africa, Sudan, and West Africa. The color infrared photography includes images of the tropical rain forests of South America and South and Southeast Asia. Other examples include photographs of floods in Argentina, photos of Lake Chad in Africa, Coastal Madagascar, the Aswan dam and the Nile, geologic features of North Africa, the center pivot irrigation land areas of Saudi Arabia, flooding in Asian rivers, and sediment plumes of South American and South and Southeast Asian coasts.

Metal pollution loading, Manzalah lagoon, Nile delta, Egypt: Implications for aquaculture

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siegel, F.R.; Slaboda, M.L.; Stanley, D.J.

1994-03-01

High cultural enrichment factors are found for Hg (13 x), Pb (22.1 x), and other potentially toxic metals (e.g., Sn, Zn, Cu, Ag) in the upper 20 cm of sediment cores from the southeastern Ginka subbasin of Manzalah lagoon, Nile delta, Egypt. Cores from other areas of the lagoon show little metal loading. Metal loading followed the closure of the Aswan High Dam, the availability of abundant cheap electricity, and the development of major power-based industries. Industrial wastes containing potentially toxic metals are dumped into the Nile delta drain system. The load carried by Bahr El-Baqar drain discharges into themore » Ginka subbasin, which acts as a sink and results in metal loading of the sediment deposited there. Further development of aquaculture in this subbasin, of food-stuff agriculture on recently reclaimed lagoon bottom, or where irrigation waters come from Bahr El-Baqar drain or its discharge should be halted or strictly limited until potentially toxic metals in the drain waters and sediment are removed and polluted input drastically reduced. This environmental assessment of heavy metals in aquaculture or agriculture development should extend to other waterbodies in the northern Nile delta, particularly Idku lagoon and Lake Mariut, where industrial metal-bearing wastes discharge into the waterbodies. 21 refs., 7 figs., 3 tabs.« less

Biography of Professor M. El-Bahay Issawi

NASA Astrophysics Data System (ADS)

Abdeen, Mamdouh M.

2017-12-01

Prof. Mohamed El-Bahay Issawi is a remarkable geologist and is without doubt one of the most important Egyptian geologists ever. His work in the Western Desert is extensive and legendary, and it is hard to imagine any single geologist ever again matching the extent of his field work in that remote region. He has had an enormously productive career involving a wide variety of research and applied topics. He discovered the Abu Tartur phosphate deposits, iron ore deposits of the Bahariya Oasis, and the Kalabsha kaolin deposits south of Aswan. He did extensive field work and aerial-photo mapping of the Western Desert over many years and authored many carefully documented papers that are still cited today. He wrote several books about the Phanerozoic geology of Egypt. Prof. Issawi has served his science and his nation over his long and outstanding career.

The International Heat Stress Genotype Experiment for Modeling Wheat Response to Heat: Field Experiments and AgMIP-Wheat Multi-Model Simulations

NASA Technical Reports Server (NTRS)

Martre, Pierre; Reynolds, Matthew P.; Asseng, Senthold; Ewert, Frank; Alderman, Phillip D.; Cammarano, Davide; Maiorano, Andrea; Ruane, Alexander C.; Aggarwal, Pramod K.; Anothai, Jakarat;

Predicting morphological changes DS New Naga-Hammadi Barrage for extreme Nile flood flows: A Monte Carlo analysis.

PubMed

Sattar, Ahmed M A; Raslan, Yasser M

2014-01-01

While construction of the Aswan High Dam (AHD) has stopped concurrent flooding events, River Nile is still subject to low intensity flood waves resulting from controlled release of water from the dam reservoir. Analysis of flow released from New Naga-Hammadi Barrage, which is located at 3460 km downstream AHD indicated an increase in magnitude of flood released from the barrage in the past 10 years. A 2D numerical mobile bed model is utilized to investigate the possible morphological changes in the downstream of Naga-Hammadi Barrage from possible higher flood releases. Monte Carlo simulation analyses (MCS) is applied to the deterministic results of the 2D model to account for and assess the uncertainty of sediment parameters and formulations in addition to sacristy of field measurements. Results showed that the predicted volume of erosion yielded the highest uncertainty and variation from deterministic run, while navigation velocity yielded the least uncertainty. Furthermore, the error budget method is used to rank various sediment parameters for their contribution in the total prediction uncertainty. It is found that the suspended sediment contributed to output uncertainty more than other sediment parameters followed by bed load with 10% less order of magnitude.

Predicting morphological changes DS New Naga-Hammadi Barrage for extreme Nile flood flows: A Monte Carlo analysis

PubMed Central

Sattar, Ahmed M.A.; Raslan, Yasser M.

2013-01-01

While construction of the Aswan High Dam (AHD) has stopped concurrent flooding events, River Nile is still subject to low intensity flood waves resulting from controlled release of water from the dam reservoir. Analysis of flow released from New Naga-Hammadi Barrage, which is located at 3460 km downstream AHD indicated an increase in magnitude of flood released from the barrage in the past 10 years. A 2D numerical mobile bed model is utilized to investigate the possible morphological changes in the downstream of Naga-Hammadi Barrage from possible higher flood releases. Monte Carlo simulation analyses (MCS) is applied to the deterministic results of the 2D model to account for and assess the uncertainty of sediment parameters and formulations in addition to sacristy of field measurements. Results showed that the predicted volume of erosion yielded the highest uncertainty and variation from deterministic run, while navigation velocity yielded the least uncertainty. Furthermore, the error budget method is used to rank various sediment parameters for their contribution in the total prediction uncertainty. It is found that the suspended sediment contributed to output uncertainty more than other sediment parameters followed by bed load with 10% less order of magnitude. PMID:25685476

Reducing seclusion and restraint: meeting the organizational challenge.

PubMed

Visalli, H; McNasser, G

2000-07-01

The Mohawk Valley Psychiatric Center has experienced a major reduction in the use of seclusion and restraint in the past five years. It has used the traditional quality improvement (QI) tools like the Plan Do Check Act, Flowcharts, Fishbone diagrams, and Parieto Charts as suggested in the QI literature. The original work to reduce seclusion and restraint are described in two previous articles by Visalli and McNasser. This article describes the additional work since that time. The seclusion/restraint rate in adult service per 1,000 patient days is 0.13 for restraint and 0.15 for seclusion for calendar year 1998. Children and youth service also has comparatively minimal use of seclusion and restraint. The success of this program is attributed to the organizational leadership and the interdisciplinary approach taken to provide individualized treatment. Many of the initiatives stem from a working relationship with patients on how to improve customer service.

An overview of self-consistent methods for fiber-reinforced composites

NASA Technical Reports Server (NTRS)

Gramoll, Kurt C.; Freed, Alan D.; Walker, Kevin P.

1991-01-01

The Walker et al. (1989) self-consistent method to predict both the elastic and the inelastic effective material properties of composites is examined and compared with the results of other self-consistent and elastically based solutions. The elastic part of their method is shown to be identical to other self-consistent methods for non-dilute reinforced composite materials; they are the Hill (1965), Budiansky (1965), and Nemat-Nasser et al. (1982) derivations. A simplified form of the non-dilute self-consistent method is also derived. The predicted, elastic, effective material properties for fiber reinforced material using the Walker method was found to deviate from the elasticity solution for the v sub 31, K sub 12, and mu sub 31 material properties (fiber is in the 3 direction) especially at the larger volume fractions. Also, the prediction for the transverse shear modulus, mu sub 12, exceeds one of the accepted Hashin bounds. Only the longitudinal elastic modulus E sub 33 agrees with the elasticity solution. The differences between the Walker and the elasticity solutions are primarily due to the assumption used in the derivation of the self-consistent method, i.e., the strain fields in the inclusions and the matrix are assumed to remain constant, which is not a correct assumption for a high concentration of inclusions.

Correlation of the major late Jurassic —early Tertiary low- and highstand cycles of south-west Egypt and north-west Sudan

NASA Astrophysics Data System (ADS)

Wycisk, Peter

1994-12-01

The mainly continental deposits of northwest Sudan and south-west Egypt have been correlated with coeval shallow marine and marine deposits in northern Egypt along a north-south running cross-section, based on surface and subsurface data. The palaeodepth curve of northern Egypt illustrates the gradual seal-level rise, reaching its maximum during the Late Cretaceous with conspicuous advances during the Aptian and late Cenomanian. A general highstand is also recorded during the Campanian-Maastrichtian in north-west Sudan. A detailed facies correlation is given for the Aptian and late Cenomanian highstand in western Egypt. The correlation of the Cenomanian Bahariya and Maghrabi formations displays short-term relative sealevel fluctuations. The interpretation illustrates the extensiveness of related erosional processes in the hinterland, partly intensified by temporarily uplift of the Uweinat-Aswan High in the south. Regional uplift and constant erosion took place in south-west Egypt during Coniacian and Santonian times. The regional stratigraphic gaps and uncertain interpretation of the Bahariya Uplift are induced by the influence of the Trans-African Lineament, especially during the Late Cretaceous. Low-stand fluvial sheet sandstones characterized by non-cyclic sequence development and high facies stability occur, especially in the Neocomian and early Turonian. During the Barremian and Albian, fluvial architecture changes to more cyclic fluvial sequences and increasing soil formation, due to increasing subsidence, more humid climatic conditions and the generally rising sea level, culminating in the extensive shallow marine Abu Ballas and Maghrabi formations.

Ostrich (Struthio camelus) production in Egypt.

PubMed

Cooper, R G; Mahrose, K M A; El-Shafei, M; Marai, I F M

2008-06-01

This review discusses the historical, developmental and practices of ostrich farming in Egypt. In the early 20th century, ostrich farming was very important for production of ostrich feathers and documents were produced to perfect the art of procuring the plumes from the birds and subsequently processing them. Pharaohs used ostrich feathers for adornment. Of 43 provinces, 12 were featured in 2003-2004 as farming ostriches: Alexandria, Al-Behera, Al-Dakahlia, Al-Wadi Al-Gadid, Aswan, Cairo, El-Sharkia, Geiza, Ismailia, Kafr-El-Sheikh, Matrouh and Nubaria. Abattoirs and tanneries specialising in ostrich handling are limited to two. Egypt has numerous strengths and opportunities to develop its ostrich sector. Rising meat prices suggest that fresh ostrich meat is unaffordable to many locals. Funds may be allocated to local advertising campaigns to promote ostrich meat; provision of incentives to farmers; and improving the capacity of abattoirs.

Modelling the water-agricultural sector in Rosetta, Egypt: exploring the interaction between water and food

NASA Astrophysics Data System (ADS)

Sušnik, Janez; Vamvakeridou-Lyroudia, Lydia; Savic, Dragan; Kapelan, Zoran

2014-05-01

An integrated System Dynamics Model for the Rosetta region, Egypt, assessing local water balance and agricultural yield to 2050, is presented. Fifty-seven simulations are analysed to better understand potential impacts on water and food security resulting from climate and social change and local/regional policy decisions related to the agricultural sector. Water limitation is a national issue: Egypt relies on the Nile for >95% of supply, and the flow of which is regulated by the Aswan High Dam. Egypt's share water of Aswan water is limited to 55 x 19 m3 yr-1. Any reduction in supply to the reservoir or increase in demand (e.g. from an expanding agricultural sector), has the potential to lead to a serious food and water supply situation. Results show current water resource over-exploitation. The remaining suite of 56 simulations, divided into seven scenarios, also mostly show resource overexploitation. Only under significant increases to Nile flow volumes was the trend reversed. Despite this, by threading together multiple local policies to reduce demand and improve/maintain supply, water resource exploitation can be mitigated while allowing for agricultural development. By changing cropping patterns, it is possible to improve yield and revenue, while using up to 21% less water in 2050 when compared with today. The results are useful in highlighting pathways to improving future water resource availability. Many policies should be considered in parallel, introducing redundancy into the policy framework. We do not suggest actual policy measures; this was beyond the scope of the work. This work highlights the utility of systems modelling of complex systems such as the water-food nexus, with the potential to extend the methodology to other studies and scales. In particular, the benefit of being able to easily modify and extend existing models in light of results from initial modelling efforts is cited. Analysis of initial results led to the hypothesis that by producing

A climate responsive urban design tool: a platform to improve energy efficiency in a dry hot climate

NASA Astrophysics Data System (ADS)

El Dallal, Norhan; Visser, Florentine

2017-09-01

In the Middle East and North Africa (MENA) region, new urban developments should address the climatic conditions to improve outdoor comfort and to reduce the energy consumption of buildings. This article describes a design tool that supports climate responsive design for a dry hot climate. The approach takes the climate as an initiator for the conceptual urban form with a more energy-efficient urban morphology. The methodology relates the different passive strategies suitable for major climate conditions in MENA region (dry-hot) to design parameters that create the urban form. This parametric design approach is the basis for a tool that generates conceptual climate responsive urban forms so as to assist the urban designer early in the design process. Various conceptual scenarios, generated by a computational model, are the results of the proposed platform. A practical application of the approach is conducted on a New Urban Community in Aswan (Egypt), showing the economic feasibility of the resulting urban form and morphology, and the proposed tool.

Studied the geomorphogy, soil and water resources in south Egypt using geoinformation technology

NASA Astrophysics Data System (ADS)

Fayed, Abdalla; Abdel Aziz, Belal

2010-05-01

The mean objective of this study was to study the geomorphology, soil and water resources in the studied area using remote sensing techniques and GIS. The studied located in between latitudes 24o 20' and 24o 40' N and longitudes 32o 45' and 33o 40' E in Kom Ombo , Aswan governorate. The climatic situation of the studied area is characterized by a long hot dry summer, a short mild winter with little rainfall, high evaporation and low relative humidity. Based on the interpretation of ETM remote data, GIS and 3Dview the following natural resources were detected. The geomorpholical unites in the studied were Nile valley and Kom Ombo plain. Soil types were clay soil is occurred in the old cultivated land. But it is medium to coarse grained fluvial sand with gravel in the reclaimed areas. The land use and land cover for the studied area were old cultivated land, urban area and channels. Three main groundwater aquifers were confirmed, these are the Nubian sandstones aquifer, the Eocene fissured limestone aquifer and the Quaternary alluvial aquifer. Kom Ombo is the ancient site of Ombos, which is from the ancient Egyptian word ‘nubt', or ‘City of Gold'. In ancient Egypt, the city was important to the caravan routes from Nubia and various gold mines. Keywords: Remote sensing, GIS, 3D model, Natural Resources Kom Ombo

Rate of Change in Lake Level and its Impact on Reservoir-triggered Seismicity

NASA Astrophysics Data System (ADS)

Simpson, D. W.

2017-12-01

With recent interest in increased seismicity related to fluid injection, it is useful to review cases of reservoir-triggered earthquakes to explore common characteristics and seek ways to mitigate the influence of anthropogenic impacts. Three reservoirs - Koyna, India; Nurek, Tajikistan; and Aswan, Egypt - are well-documented cases of triggered earthquakes with recorded time series of seismicity and water levels that extend for more than 30 years. The geological setting, regional tectonics and modes of reservoir utilization, along with the characteristics of the reservoir-seismicity interaction, are distinctly different in each of these three cases. Similarities and differences between these three cases point to regional and local geological and hydrological structures and the rate of changes in reservoir water level as important factors controlling the presence and timing of triggered seismicity. In a manner similar to the way in which the rate of fluid injection influences injection-related seismicity, the rate of change in reservoir water level is a significant factor in determining whether or not reservoir-triggered seismicity occurs. The high rate of annual water level rise may be important in sustaining the exceptionally long sequence of earthquakes at Koyna. In addition to the rate of filling being a determining factor in whether or not earthquakes are triggered, changes in the rate of filling may influence the time of occurrence of individual earthquakes.

Geological applications of Nimbus radiation data in Middle East

NASA Technical Reports Server (NTRS)

Allison, L. J.

1976-01-01

Plateaus of Eocene limestone and exposed limestone escarpments, in Egypt and Saudi Arabia respectively, were indicated by cool brightness temperatures T sub B (less than 240 to 265 K) by the Nimbus 5 electrically scanning microwave radiometer (ESMR) over a 2-year period. Nubian sandstone, desert eolian sand and igneous metamorphic rocks were differentiated from these limestone areas by warm T sub B values (more than 265 to 300 K). Cool T sub B values in the form of a V were found over broad areas of the Nile Valley and in the western desert of central Egypt. Similar cool T sub B values were shown over limestone-dolomitic hills of the interior Homocline and the Hadramawt plateau of Saudi Arabia. Nimbus 5 and 6 ESMR T sub B values selectively identified intermediate dense rock types (limestone versus sandstone/granite) in the Lake Nasser region whose thermal inertia ranged from 0.035 to 0.06 cal cm to minus 2 C sec 1/2 to minus one half.

Integration of satellite gravity data with ground-based geophysical data for a better understanding of the structural control of groundwater flow in the Nubian Sandstone Aquifer System

NASA Astrophysics Data System (ADS)

Fathy, K.; Sultan, M.; Bettadpur, S. V.; Save, H.; Ahmed, M.; Zahran, K. H.; Emil, M. K.; Helaly, A.; Abotalib, A. Z.; Ismaiel, A.

2016-12-01

The Nubian Sandstone Aquifer System (NSAS) extends beyond Egypt's political boundaries to cover eastern Libya, northern and central Sudan and northeast Chad. The optimum utilization of this resource requires a better understanding of the connectivity of the NSAS sub-basins and the structural control on groundwater flow throughout the system. We provide an integrated (geophysics, remote sensing and field) approach to address these issues. Firstly, we evaluated GOCE-based global Geopotential models (GGMs) compared to the terrestrial gravity anomalies for 21262 sites to select the optimum model for deriving Bouguer gravity datasets. The Eigen-6C4 was found to have the lowest deviation from the terrestrial gravity anomalies. Secondly, structures and uplifts were mapped on the surface and in the sub-surface. Extensive N-S to NW-SE trending grabens were delineated in areas proximal to the Nile Valley using Palsar-derived DEMs, and hill shade maps; these depressions are here interpreted as basement structures that were reactivated during the opening of the Red Sea and the Gulf of Suez. The sinistral E-W trending faults and shear zones of the Syrian Arc were mapped in northern Egypt from Sinai and across the Eastern and Western Deserts. These structures were mapped on the surface using hill shade images and their extension in the subsurface was successfully detected from Eigen-6C4 model-derived Bouguer and TDR maps. The E-W trending basement uplift (Uweinat-Aswan uplift) was mapped in southern Egypt and the N-S trending Uweinat-Howar uplift was delineated in western Sudan and eastern Chad using TDR maps. Thirdly, hydrological analysis was conducted using GRACE spherical harmonic solutions (RL05), and CSR 0.5° X 0.5°, and JPL Mascon solutions. These showed: (1) pronounced TWS depletion over the Dakhla basin (average of three solutions: -3.03 mm/yr); (2) the south to north groundwater flow from Sudan to Egypt is impeded by the E-W trending Uweinat-Aswan basement uplift

Probing magnetic bottom and crustal temperature variations along the Red Sea margin of Egypt

USGS Publications Warehouse

Ravat, D.; Salem, A.; Abdelaziz, A.M.S.; Elawadi, E.; Morgan, P.

2011-01-01

Over 50 magnetic bottom depths derived from spectra of magnetic anomalies in Eastern Egypt along the Red Sea margin show variable magnetic bottoms ranging from 10 to 34. km. The deep magnetic bottoms correspond more closely to the Moho depth in the region, and not the depth of 580??C, which lies significantly deeper on the steady state geotherms. These results support the idea of Wasilewski and coworkers that the Moho is a magnetic boundary in continental regions. Reduced-to-pole magnetic highs correspond to areas of Younger Granites that were emplaced toward the end of the Precambrian. Other crystalline Precambrian units formed earlier during the closure of ocean basins are not strongly magnetic. In the north, magnetic bottoms are shallow (10-15. km) in regions with a high proportion of these Younger Granites. In the south, the shoaling of the magnetic bottom associated with the Younger Granites appears to be restricted to the Aswan and Ras Banas regions. Complexity in the variation of magnetic bottom depths may arise due to a combination of factors: i) regions of Younger (Precambrian) Granites with high magnetite content in the upper crust, leaving behind low Curie temperature titanomagnetite components in the middle and lower crust, ii) rise in the depth of 580??C isotherm where the crust may have been heated due to initiation of intense magmatism at the time of the Red Sea rifting (~. 20. Ma), and iii) the contrast of the above two factors with respect to the neighboring regions where the Moho and/or Curie temperature truncates lithospheric ferromagnetism. Estimates of fractal and centroid magnetic bottoms in the oceanic regions of the Red Sea are significantly below the Moho in places suggesting that oceanic uppermost mantle may be serpentinized to the depth of 15-30 km in those regions. ?? 2011 Elsevier B.V.

Geodynamical behavior of some active area in Egypt, as deduced from geodetic and gravity data

NASA Astrophysics Data System (ADS)

Issawy, E.; Mrlina, J.; Radwan, A.; Mahmoud, S.; Rayan, A.

2009-04-01

Temporal gravity variation in parallel with the space geodetic technique (GPS) had been started in Egypt for real campaigns in 1997. The geodetic networks around the High Dam, Aswan area was the first net to be measured. More than five measurement epochs were performed. The results had a considerable limit of coincidence between gravity and GPS observations. The trend of gravity changes indicated a positive stress and had the vertical displacement observed for leveling points. The lowest gravity changes along Kalabsha fault reflect extensional and/or strike component of the stress field. Also, the areas around Cairo (Greater Cairo) and due to the occurrence of an earthquake of 1992, such type of measurements were useful for monitoring the recent activity. The data of the geodetic network around Cairo after 5 campaigns showed that, the estimated horizontal velocities for almost all points are 5.5± mm/year in approximately NW-SE direction. The non-tidal changes can explain the dynamic process within the upper crust related to the development of local stress conditions. The trends of gravity changes are more or less coincident with that deduced from GPS deformation analysis and the occurrence of the main shocks in the area. In additions, in 2005 the geodetic network around the southern part of Sinai and the Gulf of Suez were established. One campaign of measurements had been performed and the gravity values were obtained.

Mutually beneficial and sustainable management of Ethiopian and Egyptian dams in the Nile Basin

NASA Astrophysics Data System (ADS)

Habteyes, Befekadu G.; Hasseen El-bardisy, Harb A. E.; Amer, Saud A.; Schneider, Verne R.; Ward, Frank A.

2015-10-01

Ongoing pressures from population growth, recurrent drought, climate, urbanization and industrialization in the Nile Basin raise the importance of finding viable measures to adapt to these stresses. Four tributaries of the Eastern Nile Basin contribute to supplies: the Blue Nile (56%), White Nile-Albert (14%), Atbara (15%) and Sobat (15%). Despite much peer reviewed work addressing conflicts on the Nile, none to date has quantitatively examined opportunities for discovering benefit sharing measures that could protect negative impacts on downstream water users resulting from new upstream water storage developments. The contribution of this paper is to examine the potential for mutually beneficial and sustainable benefit sharing measures from the development and operation of the Grand Ethiopian Renaissance Dam while protecting baseline flows to the downstream countries including flows into the Egyptian High Aswan Dam. An integrated approach is formulated to bring the hydrology, economics and institutions of the region into a unified framework for policy analysis. A dynamic optimization model is developed and applied to identify the opportunities for Pareto Improving measures to operate these two dams for the four Eastern Nile Basin countries: Ethiopia, South Sudan, Sudan, and Egypt. Results indicate a possibility for one country to be better off (Ethiopia) and no country to be worse off from a managed operation of these two storage facilities. Still, despite the optimism of our results, considerable diplomatic negotiation among the four riparians will be required to turn potential gains into actual welfare improvements.

From source to sink: Exploring the Quaternary history of the Nile

NASA Astrophysics Data System (ADS)

Woodward, J. C.; Williams, M. A. J.; Garzanti, E.; Macklin, M. G.; Marriner, N.

2015-12-01

Nearly two thousand five hundred years have elapsed since the Greek historian Herodotus (ca. 485-425 BC) posed a number of fundamental questions about the source, age, and flood regime of the River Nile. Herodotus travelled widely in Egypt in around 450 BC - mainly in the Delta and Lower Egypt, but he may have journeyed as far upstream as Aswan and the First Cataract. A keen observer of nature, with a questioning intellect, Herodotus very quickly discerned that the dark alluvial soils of Egypt were very different from the desert soils of Syria and Libya, and inferred that they were derived from the Ethiopian headwaters of the Nile. Herodotus was the first to recognize that Egyptian civilization was, as he put it, ;the gift of the river; (Griffiths, 1966) since he understood that, without the regular and reliable hundred days of flooding during the summer months, and the annual deposition of silts along the floodplains, agriculture would not have been possible on any significant scale under the desert climate of the Nile Valley.

Physiological loading of joints prevents cartilage degradation through CITED2

PubMed Central

Leong, Daniel J.; Li, Yong H.; Gu, Xiang I.; Sun, Li; Zhou, Zuping; Nasser, Philip; Laudier, Damien M.; Iqbal, Jameel; Majeska, Robert J.; Schaffler, Mitchell B.; Goldring, Mary B.; Cardoso, Luis; Zaidi, Mone; Sun, Hui B.

2011-01-01

Both overuse and disuse of joints up-regulate matrix metalloproteinases (MMPs) in articular cartilage and cause tissue degradation; however, moderate (physiological) loading maintains cartilage integrity. Here, we test whether CBP/p300-interacting transactivator with ED-rich tail 2 (CITED2), a mechanosensitive transcriptional coregulator, mediates this chondroprotective effect of moderate mechanical loading. In vivo, hind-limb immobilization of Sprague-Dawley rats up-regulates MMP-1 and causes rapid, histologically detectable articular cartilage degradation. One hour of daily passive joint motion prevents these changes and up-regulates articular cartilage CITED2. In vitro, moderate (2.5 MPa, 1 Hz) intermittent hydrostatic pressure (IHP) treatment suppresses basal MMP-1 expression and up-regulates CITED2 in human chondrocytes, whereas high IHP (10 MPa) down-regulates CITED2 and increases MMP-1. Competitive binding and transcription assays demonstrate that CITED2 suppresses MMP-1 expression by competing with MMP transactivator, Ets-1 for its coactivator p300. Furthermore, CITED2 up-regulation in vitro requires the p38δ isoform, which is specifically phosphorylated by moderate IHP. Together, these studies identify a novel regulatory pathway involving CITED2 and p38δ, which may be critical for the maintenance of articular cartilage integrity under normal physical activity levels.—Leong, D. J., Li, Y. H., Gu, X. I., Sun, L., Zhou, Z., Nasser, P., Laudier, D. M., Iqbal, J., Majeska, R. J., Schaffler, M. B., Goldring, M. B., Cardoso, L., Zaidi, M., Sun, H. B. Physiological loading of joints prevents cartilage degradation through CITED2. PMID:20826544

Compressive deformation of a single microcapsule

NASA Astrophysics Data System (ADS)

Liu, K. K.; Williams, D. R.; Briscoe, B. J.

1996-12-01

This paper reports an experimental and theoretical study of the compressive behavior of single microcapsules; that is, liquid-filled cellular entities (approximately 65 μm in diameter) with a thin polymeric membrane wall. An experimental technique which allows the simultaneous measurement of both the compressive displacement and the reaction forces of individual microcapsules deformed between two parallel plates up to a dimensionless approach [(compressive displacement)/(initial particle diameter)] of 60% is described. The corresponding major geometric parameters of the deformed microcapsule, such as central lateral extension as well as the failure phenomena, are reported and recorded through a microscopic visualization system. The elastic modulus, the bursting strength of the membrane, and the pressure difference across the membrane are computed by using a theoretical analysis which is also presented in this paper. This theoretical model, which was developed by Feng and Yang [

Interaction of surface water and groundwater in the Nile River basin: isotopic and piezometric evidence

NASA Astrophysics Data System (ADS)

Kebede, Seifu; Abdalla, Osman; Sefelnasr, Ahmed; Tindimugaya, Callist; Mustafa, Osman

2017-05-01

Past discussions around water-resources management and development in the River Nile basin disregard groundwater resources from the equation. There is an increasing interest around factoring the groundwater resources as an integral part of the Nile Basin water resources. This is hampered by knowledge gap regarding the groundwater resources dynamics (recharge, storage, flow, quality, surface-water/groundwater interaction) at basin scale. This report provides a comprehensive analysis of the state of surface-water/groundwater interaction from the headwater to the Nile Delta region. Piezometric and isotopic (δ18O, δ2H) evidence reveal that the Nile changes from a gaining stream in the headwater regions to mostly a loosing stream in the arid lowlands of Sudan and Egypt. Specific zones of Nile water leakage to the adjacent aquifers is mapped using the two sources of evidence. Up to 50% of the surface-water flow in the equatorial region of the Nile comes from groundwater as base flow. The evidence also shows that the natural direction and rate of surface-water/groundwater interaction is largely perturbed by human activities (diversion, dam construction) particularly downstream of the Aswan High Dam in Egypt. The decrease in discharge of the Nile River along its course is attributed to leakage to the aquifers as well as to evaporative water loss from the river channel. The surface-water/groundwater interaction occurring along the Nile River and its sensitivity to infrastructure development calls for management strategies that account groundwater as an integral part of the Nile Basin resources.

Reservoir inflow forecasting with a modified coactive neuro-fuzzy inference system: a case study for a semi-arid region

NASA Astrophysics Data System (ADS)

Allawi, Mohammed Falah; Jaafar, Othman; Mohamad Hamzah, Firdaus; Mohd, Nuruol Syuhadaa; Deo, Ravinesh C.; El-Shafie, Ahmed

2017-10-01

Existing forecast models applied for reservoir inflow forecasting encounter several drawbacks, due to the difficulty of the underlying mathematical procedures being to cope with and to mimic the naturalization and stochasticity of the inflow data patterns. In this study, appropriate adjustments to the conventional coactive neuro-fuzzy inference system (CANFIS) method are proposed to improve the mathematical procedure, thus enabling a better detection of the high nonlinearity patterns found in the reservoir inflow training data. This modification includes the updating of the back propagation algorithm, leading to a consequent update of the membership rules and the induction of the centre-weighted set rather than the global weighted set used in feature extraction. The modification also aids in constructing an integrated model that is able to not only detect the nonlinearity in the training data but also the wide range of features within the training data records used to simulate the forecasting model. To demonstrate the model's efficacy, the proposed CANFIS method has been applied to forecast monthly inflow data at Aswan High Dam (AHD), located in southern Egypt. Comparative analyses of the forecasting skill of the modified CANFIS and the conventional ANFIS model are carried out with statistical score indicators to assess the reliability of the developed method. The statistical metrics support the better performance of the developed CANFIS model, which significantly outperforms the ANFIS model to attain a low relative error value (23%), mean absolute error (1.4 BCM month-1), root mean square error (1.14 BCM month-1), and a relative large coefficient of determination (0.94). The present study ascertains the better utility of the modified CANFIS model in respect to the traditional ANFIS model applied in reservoir inflow forecasting for a semi-arid region.

The role of predictive uncertainty in the operational management of reservoirs

NASA Astrophysics Data System (ADS)

Todini, E.

2014-09-01

The present work deals with the operational management of multi-purpose reservoirs, whose optimisation-based rules are derived, in the planning phase, via deterministic (linear and nonlinear programming, dynamic programming, etc.) or via stochastic (generally stochastic dynamic programming) approaches. In operation, the resulting deterministic or stochastic optimised operating rules are then triggered based on inflow predictions. In order to fully benefit from predictions, one must avoid using them as direct inputs to the reservoirs, but rather assess the "predictive knowledge" in terms of a predictive probability density to be operationally used in the decision making process for the estimation of expected benefits and/or expected losses. Using a theoretical and extremely simplified case, it will be shown why directly using model forecasts instead of the full predictive density leads to less robust reservoir management decisions. Moreover, the effectiveness and the tangible benefits for using the entire predictive probability density instead of the model predicted values will be demonstrated on the basis of the Lake Como management system, operational since 1997, as well as on the basis of a case study on the lake of Aswan.

Quantifying Modern Recharge and Depletion Rates of the Nubian Aquifer in Egypt

NASA Astrophysics Data System (ADS)

Ahmed, Mohamed; Abdelmohsen, Karem

2018-07-01

Egypt is currently seeking additional freshwater resources to support national reclamation projects based mainly on the Nubian aquifer groundwater resources. In this study, temporal (April 2002 to June 2016) Gravity Recovery and Climate Experiment (GRACE)-derived terrestrial water storage (TWSGRACE) along with other relevant datasets was used to monitor and quantify modern recharge and depletion rates of the Nubian aquifer in Egypt (NAE) and investigate the interaction of the NAE with artificial lakes. Results indicate: (1) the NAE is receiving a total recharge of 20.27 ± 1.95 km3 during 4/2002-2/2006 and 4/2008-6/2016 periods, (2) recharge events occur only under excessive precipitation conditions over the Nubian recharge domains and/or under a significant rise in Lake Nasser levels, (3) the NAE is witnessing a groundwater depletion of - 13.45 ± 0.82 km3/year during 3/2006-3/2008 period, (4) the observed groundwater depletion is largely related to exceptional drought conditions and/or normal baseflow recession, and (5) a conjunctive surface water and groundwater management plan needs to be adapted to develop sustainable water resources management in the NAE. Findings demonstrate the use of global monthly TWSGRACE solutions as a practical, informative, and cost-effective approach for monitoring aquifer systems across the globe.

Quantifying Modern Recharge and Depletion Rates of the Nubian Aquifer in Egypt

NASA Astrophysics Data System (ADS)

Ahmed, Mohamed; Abdelmohsen, Karem

2018-02-01

Egypt is currently seeking additional freshwater resources to support national reclamation projects based mainly on the Nubian aquifer groundwater resources. In this study, temporal (April 2002 to June 2016) Gravity Recovery and Climate Experiment (GRACE)-derived terrestrial water storage (TWSGRACE) along with other relevant datasets was used to monitor and quantify modern recharge and depletion rates of the Nubian aquifer in Egypt (NAE) and investigate the interaction of the NAE with artificial lakes. Results indicate: (1) the NAE is receiving a total recharge of 20.27 ± 1.95 km3 during 4/2002-2/2006 and 4/2008-6/2016 periods, (2) recharge events occur only under excessive precipitation conditions over the Nubian recharge domains and/or under a significant rise in Lake Nasser levels, (3) the NAE is witnessing a groundwater depletion of - 13.45 ± 0.82 km3/year during 3/2006-3/2008 period, (4) the observed groundwater depletion is largely related to exceptional drought conditions and/or normal baseflow recession, and (5) a conjunctive surface water and groundwater management plan needs to be adapted to develop sustainable water resources management in the NAE. Findings demonstrate the use of global monthly TWSGRACE solutions as a practical, informative, and cost-effective approach for monitoring aquifer systems across the globe.

The NASA/USDA Reservoir and Lake Monitor: Present and Future Capabilities and Water Resources Applications

NASA Astrophysics Data System (ADS)

Birkett, C. M.; Beckley, B. D.; Reynolds, C. A.; Brakenridge, G. R.; Ricko, M.

2013-12-01

The USDA/NASA Global Reservoir and Lake Monitor (GRLM) provides satellite-based surface water level products for large reservoirs and lakes around the world. It utilizes a suite of NASA/CNES and ESA radar altimetry data sets and outputs near real time and archival products via a web interface. Several stakeholders utilize the products for applications that focus on water resources management and natural hazards mitigation, particularly in arid and semi-arid regions. The satellite data sets prove particularly useful in un-gauged or poorly gauged basins where in situ data is sparse. Here, we present water-level product examples based on data from the NASA/CNES Jason-2/OSTM mission, and the new ISRO/CNES SARAL mission. We also demonstrate product application from the viewpoint of various end users who have interests ranging from crop production and fisheries, to regional security and climate change. In the current phase of the program the team is also looking to the potential of additional lake/reservoir products such as areal extent (NASA/MODIS), lake volume variations (combined altimetry/imagery), and model-derived water levels, that will enhance the GRLM via improved observation and prediction, and provide a more global lake basin monitoring capability. Surface water level variations for Lake Nasser.

The present status of reservoir induced seismicity investigations with special emphasis on Koyna earthquakes

NASA Astrophysics Data System (ADS)

Gupta, Harsh K.

1985-10-01

The status of Reservoir Induced Seismicity (RIS) has been reviewed periodically (Rothé, 1968, 1973; Gupta and Rastogi, 1976; Simpson, 1976; Packer et al., 1979). In the present paper, the significant work carried out during the last three years on RIS is reviewed. An earthquake of magnitude 5 {1}/{2} occurred on November 14, 1981 in the vicinity of Aswan Lake, Egypt, 17 years after the filling started in 1964. This event occurred 4 days after the seasonal maximum in the reservoir water level and was followed by a long sequence of aftershocks. Another event of magnitude 4 {1}/{2} occurred in the vicinity of Aswan Lake on August 20, 1982. Results of preliminary investigations indicate that this seismic activity is reservoir induced. Recent analyses of induced seismic events at Nurek Reservoir U.S.S.R., show that the second stage of filling during August to December 1976, increasing the maximum depth from 120 m to 200 m, was accompanied by an intense burst of shallow seismic activity. An outward migration from the centre of the reservoir, possibly associated with diffusion of pore pressure, is revealed by the temporal distribution of earthquake foci. A variety of investigations including the in situ measurement of tectonic stress, pore pressure, permeability, distribution of faults, etc., in addition to monitoring seismicity, have been undertaken in the vicinity of the Monticello Reservoir, South Carolina. The largest reservoir induced earthquake is predicted not to exceed magnitude 5. The Koyna Reservoir, India, continues to be the most outstanding example of RIS. Three earthquakes of magnitude $˜5 occurred in September 1980. Earthquakes of magnitude 4 occur frequently in the vicinity of Koyna, the latest being on February 5, 1983. Events that occurred during the period 1967-1973 have been relocated using better procedures and are found to be much shallower and the epicentres less diffused. Location of 12 earthquakes of Ms ⩾ 4.0, their foreshocks and aftershocks

Letter from Gustavus. While Rome burns.

PubMed

Brown, W E

1994-01-01

The religious command to the ancient nomads in Israel to multiply and subdue the earth is still obeyed across the world. In India and China high fertility ensures the requisite work force for intensive agriculture and the care of the elderly. In pastoral societies wealth and social status depend on the number of livestock possessed, with the result of overgrazing, soil erosion, and desertification. Most ecosystem and biospheric deterioration stems from two causes: 1) the false notion inherited from ancient religious beliefs that human beings are exempt from natural constraints; and 2) the fallacious idea that science and technology will overcome the looming prospects of environmental catastrophe. The ill-fated examples of the Aswan Dam in Egypt, the devastation of the rich soils in the Mississippi Basin, and the destruction of California attest to the contrary. In addition, the existing nuclear arsenal as well as obsolescent nuclear power plants harbor a potential disaster. There is a desperate struggle to feed multiplying populations, which results in mining all the resources within the boundaries of nation states, or, once they become exhausted, taking the lands and resources of others. Unless the same rules are applied to the human species as are to scientific investigation, there will be no more preserved lands, seas, and ecosystems left. In Third World countries this phenomenon is already taking place on a large scale when parks and nature preserves must resort to armed wardens to protect the wildlife and habitat from encroachers scavenging for food and fuelwood. In the industrialized countries this desperation does not appear so manifestly yet because it is allayed by the rapacious extraction of the resources of poorer nations by multinationals.

STS-56 Earth observation of the northeastern Nile Delta

NASA Image and Video Library

1993-04-17

STS-56 Earth observation of the northeastern Nile Delta was photographed from the Earth-orbiting Discovery, Orbiter Vehicle (OV) 103. The branch of the Nile featured in the frame is Daimietta. The Suez Canal marks the boundary of the Nile Delta agriculture and the Sinai Desert to the right. Lake Masada, the dark waterlogged area to the west (left) of Port Said is becoming more saline as the Aswan Dam has reduced sediment downstream. This sediment reduction, according to NASA scientists studying the STS-56 photography, has resulted in increased coastal erosion and the intrusion of a salt-water lens to the ground water, particularly in the northeastern portions of the delta. Center pivot irrigation fields are located along either side of the Ramses Canal, which connects the Daimietta Nile with Great Bitter Lake. This canal has been re-dug three or four times in the past 3,000 years. Historians note that the canal's most famous use was as the departure point of the fleet of Pharaoh Necho. The fleet circumnavigated Africa clockwise from the head of the Red Sea to the Mediterranean coast of the Nile (probably the Rosetta Nile) in a three-year voyage circa 660 BC.

Occurrence of Root Rot and Vascular Wilt Diseases in Roselle (Hibiscus sabdariffa L.) in Upper Egypt.

PubMed

Hassan, Naglaa; Shimizu, Masafumi; Hyakumachi, Mitsuro

2014-03-01

Roselle (Hibiscus sabdariffa L.) family Malvaceae is an important crop used in food, cosmetics and pharmaceutics industries. Roselle is cultivated mainly in Upper Egypt (Qena and Aswan governorates) producing 94% of total production. Root rot disease of roselle is one of the most important diseases that attack both seedlings and adult plants causing serious losses in crop productivity and quality. The main objective of the present study is to identify and characterize pathogens associated with root rot and wilt symptoms of roselle in Qena, Upper Egypt and evaluate their pathogenicity under greenhouse and field condition. Fusarium oxysporum, Macrophomina phaseolina, Fusarium solani, Fusarium equiseti and Fusarium semitectum were isolated from the natural root rot diseases in roselle. All isolated fungi were morphologically characterized and varied in their pathogenic potentialities. They could attack roselle plants causing damping-off and root rot/wilt diseases in different pathogenicity tests. The highest pathogenicity was caused by F. oxysporum and M. phaseolina followed by F. solani. The least pathogenic fungi were F. equiseti followed by F. semitectum. It obviously noted that Baladi roselle cultivar was more susceptible to infection with all tested fungi than Sobhia 17 under greenhouse and field conditions. This is the first report of fungal pathogens causing root rot and vascular wilt in roselle in Upper Egypt.

Nile damming as plausible cause of extinction and drop in abundance of deep-sea shrimp in the western Mediterranean over broad spatial scales

NASA Astrophysics Data System (ADS)

Cartes, J. E.; Maynou, F.; Fanelli, E.

2011-11-01

Greatly increased retention of flow in Nile River reservoirs was initiated in 1964, after completion of the Aswan High Dam, which induced important oceanographic changes in the Mediterranean Sea, including deep waters (below a depth of 150 m). Based on an analysis of data series starting in the 1940s/1950s, the giant red shrimp Aristaeomorpha foliacea has become locally extinct off of the Catalonian coasts (and elsewhere in the northwestern Mediterranean) at depths of 400-900 m, with a simultaneous and significant drop in the catches of red shrimp, Aristeus antennatus, in the second half of the 1960s. The extinction and sharp decline of deep-shrimp populations off Catalonian coast (at ca. 3200 km westwards from Nile Delta) followed the 1964 drop in Nile discharge with a delay of ca. 3-5 yrs (breakpoint analysis applied to data series). The breakpoints detected in the second half of 1960s both in Nile runoff and shrimps’ abundance were independent of climatic events in the study area (e.g. changes in NAO) and occurred before the increase in fishing effort off Catalonian coasts (breakpoint in 1973-1974). The Levantine Intermediate Water (LIW), inhabited by A. foliacea in the western Basin, had significant temperature (T) and salinity (S) increases in the 1950-1970 period, and Nile damming has contributed about 45% of the total S increase of Western Mediterranean deep-water masses from the 1960s to the late 1990s (Skliris and Lascaratos, 2004). This had to increase, for instance, LIW salinity at its formation site in the eastern Mediterranean. Nile damming was probably a triggering factor for the extinction/drop in abundance of deep-sea shrimp off Catalonian coasts.

Joint Egypt/United States report on Egypt/United States cooperative energy assessment. Volume 4 of 5 Vols. Annexes 6--10

DOE Office of Scientific and Technical Information (OSTI.GOV)

Purvis, Edward E.; Teagan, Peter; Little, Arthur D.

1979-04-01

Annex 6, which investigates the possible hydroelectric resources of Egypt, reveals that presently the only existing sites are on the upper Nile at the High and Aswan Dams. There are 8 sites on the Nile where it is practical to add hydroelectric generation and, of these, only 4 are feasible for immediate construction. There are also pumped-storage sites on the Nile and the Red Sea. There is also the Qattara Depression in the Western Desert which can be utilized for conventional, as well as pumped-storage generation, by bringing water from the Mediterranean Sea to the depression by canal or tunnel.more » The options were considered for construction of hydro plants to met the electric load growth of Egypt when other forms of energy supply would be integrated into a comprehensive supply pattern. In Annex 7, the prospective use of nuclear energy to meet Egypt's resources (uranium and thorium) to implement a nuclear energy program, and potential effects of the expanded use of nuclear energy are discussed. Annex 8 discusses solar energy (technology descriptions and impacts, solar thermal power, photovoltaics). Also wind power generation, biomass utilization, desalination, solar air conditioning and refrigeration, and cost of power from diesel engines are discussed. Annex 9 covers geothermal potentials in Egypt, discussing resources with temperatures above 180/sup 0/C; from 150 to 180/sup 0/C; from 100 to 150/sup 0/C; and with temperatures below 100/sup 0/C. Annex 10 discusses the electric power systems in Egypt. The following subjects are covered: existing electric power systems; electrical power facilities under construction or planned for construction by 1985; past and projected growth of electrical energy; distribution; and electrical power system projected from 1985 to 2000. (MCW)« less

Impact of climate change on precipitation distribution and water availability in the Nile using CMIP5 GCM ensemble.

NASA Astrophysics Data System (ADS)

Mekonnen, Z. T.; Gebremichael, M.

2017-12-01

ABSTRACT In a basin like the Nile where millions of people depend on rainfed agriculture and surface water resources for their livelihoods, changes in precipitation will have tremendous social and economic consequences. General circulation models (GCMs) have been associated with high uncertainty in their projection of future precipitation for the Nile basin. Some studies tried to compare performance of different GCMs by doing a Multi-Model comparison for the region. Many indicated that there is no single model that gives the "best estimate" of precipitation for a very complex and large basin like the Nile. In this study, we used a combination of satellite and long term rain gauge precipitation measurements (TRMM and CenTrends) to evaluate the performance of 10 GCMs from the 5th Coupled Model Intercomparison Project (CMIP5) at different spatial and seasonal scales and produce a weighted ensemble projection. Our results confirm that there is no single model that gives best estimate over the region, hence the approach of creating an ensemble depending on how the model performed in specific areas and seasons resulted in an improved estimate of precipitation compared with observed values. Following the same approach, we created an ensemble of future precipitation projections for four different time periods (2000-2024, 2025-2049 and 2050-2100). The analysis showed that all the major sub-basins of the Nile will get will get more precipitation with time, even though the distribution with in the sub basin might be different. Overall the analysis showed a 15 % increase (125 mm/year) by the end of the century averaged over the area up to the Aswan dam. KEY WORDS: Climate Change, CMIP5, Nile, East Africa, CenTrends, Precipitation, Weighted Ensembles

Relationship between pure Schistosoma haematobium infection in Upper Egypt and irrigation systems. Part II: Host characteristics. The general prevalence of Schistosoma haematobium, age and sex distribution.

PubMed

Hammam, H M; Allam, F A; Hassanein, F

1975-01-01

The epidemiology of bilharziasis was studied in four villages in Assiut Governorate. These villages were almost similar with respect to their socioeconomic conditions, modes of living, availability and date of introduction of medical services. The first village, Gezirat El-Maabda, has a basin system of irrigation. The other three villages had shifted to the perennial system of irrigation for three years in Nazza Karrar, 26 years in El-Ghorayeb and 95 years in Garf Sarhan and were similar with respect to proximity to water courses. So the only variable of importance between the four villages was the mode of irrigation. Bilharziasis was diagnosed by detection of eggs in urine or faeces. A definitive relationship between the prevalence of S. haematobium infection and the type of irrigation system was further documented. A low prevalence was found in Gezirat El-Maabda (2.95%). In the other three villages a much higher prevalence existed (31.9%, 46.2% & 38.9% in Nazza Karar, El-Ghorayeb and Garf Sarhan respectively). The higher prevalence of S. haematobium in Nazza Karar (31.9%) only three years after introduction of perennial irrigation was a disappointing finding. It can be considered as an evidence against the elaborate measures and precautions planned and incompletely implemented before or after the establishment of Aswan High Dam. Not a single case of S. mansoni was encountered during this study. As regards the age and sex distribution of S. haematobium in the three villages irrigated perennially, a steep rise started at the age group 5-9 years reaching a peak at the age group 10-14 years. In Gezirat El-Maabda the peak was reached at later age (15-19 years). The cause of this difference was explained. Males showed a higher rate of infection than females in almost all age groups of the four village studied.

Three Least-Squares Minimization Approaches to Interpret Gravity Data Due to Dipping Faults

NASA Astrophysics Data System (ADS)

Abdelrahman, E. M.; Essa, K. S.

2015-02-01

We have developed three different least-squares minimization approaches to determine, successively, the depth, dip angle, and amplitude coefficient related to the thickness and density contrast of a buried dipping fault from first moving average residual gravity anomalies. By defining the zero-anomaly distance and the anomaly value at the origin of the moving average residual profile, the problem of depth determination is transformed into a constrained nonlinear gravity inversion. After estimating the depth of the fault, the dip angle is estimated by solving a nonlinear inverse problem. Finally, after estimating the depth and dip angle, the amplitude coefficient is determined using a linear equation. This method can be applied to residuals as well as to measured gravity data because it uses the moving average residual gravity anomalies to estimate the model parameters of the faulted structure. The proposed method was tested on noise-corrupted synthetic and real gravity data. In the case of the synthetic data, good results are obtained when errors are given in the zero-anomaly distance and the anomaly value at the origin, and even when the origin is determined approximately. In the case of practical data (Bouguer anomaly over Gazal fault, south Aswan, Egypt), the fault parameters obtained are in good agreement with the actual ones and with those given in the published literature.

Occurrence of Root Rot and Vascular Wilt Diseases in Roselle (Hibiscus sabdariffa L.) in Upper Egypt

PubMed Central

Hassan, Naglaa; Shimizu, Masafumi

2014-01-01

Roselle (Hibiscus sabdariffa L.) family Malvaceae is an important crop used in food, cosmetics and pharmaceutics industries. Roselle is cultivated mainly in Upper Egypt (Qena and Aswan governorates) producing 94% of total production. Root rot disease of roselle is one of the most important diseases that attack both seedlings and adult plants causing serious losses in crop productivity and quality. The main objective of the present study is to identify and characterize pathogens associated with root rot and wilt symptoms of roselle in Qena, Upper Egypt and evaluate their pathogenicity under greenhouse and field condition. Fusarium oxysporum, Macrophomina phaseolina, Fusarium solani, Fusarium equiseti and Fusarium semitectum were isolated from the natural root rot diseases in roselle. All isolated fungi were morphologically characterized and varied in their pathogenic potentialities. They could attack roselle plants causing damping-off and root rot/wilt diseases in different pathogenicity tests. The highest pathogenicity was caused by F. oxysporum and M. phaseolina followed by F. solani. The least pathogenic fungi were F. equiseti followed by F. semitectum. It obviously noted that Baladi roselle cultivar was more susceptible to infection with all tested fungi than Sobhia 17 under greenhouse and field conditions. This is the first report of fungal pathogens causing root rot and vascular wilt in roselle in Upper Egypt. PMID:24808737

Elemental analysis of granite by instrumental neutron activation analysis (INAA) and X-ray fluorescence analysis (XRF).

PubMed

El-Taher, A

2012-01-01

The instrumental neutron activation analysis technique (INAA) was used for qualitative and quantitative analysis of granite samples collected from four locations in the Aswan area in South Egypt. The samples were prepared together with their standards and simultaneously irradiated in a neutron flux of 7×10(11)n/cm(2)s in the TRIGA Mainz research reactor. Gamma-ray spectra from an hyper-pure germanium detector were analyzed. The present study provides the basic data of elemental concentrations of granite rocks. The following elements have been determined Na, Mg, K, Fe, Mn, Sc, Cr, Ti, Co, Zn, Ga, Rb, Zr, Nb, Sn, Ba, Cs, La, Ce, Nd, Sm, Eu, Yb, Lu, Hf, Ta, Th and U. The X-ray fluorescence (XRF) was used for comparison and to detect elements, which can be detected only by XRF such as F, S, Cl, Co, Cu, Mo, Ni, Pb, Se and V. The data presented here are our contribution to understanding the elemental composition of the granite rocks. Because there are no existing databases for the elemental analysis of granite, our results are a start to establishing a database for the Egyptian granite. It is hoped that the data presented here will be useful to those dealing with geochemistry, granite chemistry and related fields. Copyright © 2011 Elsevier Ltd. All rights reserved.

In vitro antischistosomal activity of venom from the Egyptian snake Cerastes cerastes.

PubMed

Hassan, Ehssan Ahmed; Abdel-Rahman, Mohamed Ahmed; Ibrahim, Mohamed Moussa; Soliman, Maha Farid Mohamed

2016-01-01

We studied the potential in vitro antischistosomal activity of Cerastes cerastes venom on adult Schistosoma mansoni worms. Live specimens of the horned viper snake, C. cerastes were collected from the Aswan Governorate (Egypt). Venom was collected from snakes by manual milking. Worms of S. mansoni were obtained from infected hamsters by perfusion and isolated from blood using phosphate buffer. Mortality rates of worms were monitored after 3 days of exposure to snake venom at LC50 and various sublethal concentrations (10, 5, 2.5µg/ml). Scanning electron microscopy was used to investigate tegumental changes in treated worms after exposure to LC50 doses of venom. The LC50 of C. cerastes venom was 21.5µg/ml. The effect of C. cerastes venom on Schistosoma worms varied according to their sex. The mortality rate of male and female worms after 48-h exposure was 83.3% and 50%, respectively. LC50 of C. cerastes venom induced mild to severe tegumental damage in Schistosoma worms in the form of destruction of the oral sucker, shrinkage and erosion of the tegument, and loss of some tubercle spines. The present study demonstrated that C. cerastes venom exerts potential in vitro antischistosomal activity in a time and dose-dependent manner. These results may warrant further investigations to develop novel schistosomicidal agents from C. cerastes snake venom.

Nile Delta exhibited a spatial reversal in the rates of shoreline retreat on the Rosetta promontory comparing pre- and post-beach protection

NASA Astrophysics Data System (ADS)

Ghoneim, Eman; Mashaly, Jehan; Gamble, Douglas; Halls, Joanne; AbuBakr, Mostafa

2015-01-01

The coastline of the Nile Delta experienced accelerated erosion since the construction of the Aswan High Dam in 1964 and, consequently, the entrapment of a large amount of river sediments behind it. The coastline of the Rosetta promontory showed the highest erosion in the Delta with an average retreat rate of 137.4 m year- 1. In 1991, in an effort to mitigate sediment loss, a 4.85 km long seawall was built on the outer margin of the promontory. For additional beach protection, 15 groins were constructed along the eastern and western sides of the seawall in 2003 and 2005. To quantify erosion and accretion patterns along the Rosetta promontory, 11 Landsat images acquired at unequal intervals during a 40 year time span (1972 and 2012) were analyzed. The positions of shorelines were automatically extracted from satellite imagery and compared with three very high resolution QuickBird and WorldView2 images for data validation. Analysis of the rates of shoreline change revealed that the construction of the seawall was largely successful in halting the recession along the tip of the promontory, which lost 10.8 km2 prior to coastal protection. Conversely, the construction of the 15 groins has negatively affected the coastal morphology of the promontory and caused a reversal from accretion to fast erosion along the promontory leeside, where some segments of the shoreline have undergone as much as 30.8 m year- 1 of erosion. Without hard structures, the tip of the Rosetta promontory would have retreated 2.3 km by 2013 and lost 7.2 km2 of land. About 10% of this land is deltaic fertile cultivated farms. Moreover, without additional protection the sides of the promontory will lose about 1.3 km2 of land and the coastline would recede at an average rate of 200 m by 2020. Unless action is taken, coastal erosion, enhanced by rising sea level, will steadily eat away the Nile Delta at an alarming rate. The successful demonstration of the advocated procedures in this study could be

Towards a Better Understanding of the Hydrologic Setting of the Nubian Sandstone Aquifer System: Inferences from Groundwater Flow Models, CL-36 Ages, and GRACE Data

NASA Astrophysics Data System (ADS)

Sultan, M.; Mohamed, A.; Yan, E.; Ahmed, E.; Sturchio, N. C.

2015-12-01

The Nubian Sandstone Aquifer System (NSAS), one of the largest (area: ~2×106 km2) groundwater systems worldwide, is formed of three major sub-basins: Kufra (Libya, NE Chad and NW Sudan), Dakhla (Egypt), and N. Sudan Platform (Sudan). To determine the mean residence time of water in the aquifer, the connectivity of its sub-basins and the groundwater flow across these sub-basins have to be understood. An integrated approach was adopted to address these issues using: (1) a regional calibrated groundwater flow model that simulates early (>10,000 years) steady-state conditions under wet climatic periods, and later (<10,000 years) transient conditions under arid condition; (2) 36Cl ages, and (3) GRACE solutions. Our findings include: (1) the NSAS was recharged (recharge: plains: 2-7 mm/yr; highlands 10-27 mm/yr) in the previous wet climatic periods on a regional scale, yet its outcrops are still receiving in dry periods appreciable precipitation over the highlands and modest (3.04±1.10 km3/yr) local recharge; (2) a progressive increase in 36Cl groundwater ages were observed along groundwater flow directions and along structures that are sub-parallel to the groundwater flow direction; (3) the NE-SW Pelusium shear zone provides a preferred groundwater flow pathway from the Kufra to the Dakhla sub-basin as evidenced by the relatively high hydraulic conductivities and relatively younger ages of groundwater along the shear zone compared to the groundwater ages in areas surrounding the shear zone; (4) the E-W trending Uweinat-Aswan basement uplift impedes groundwater flow from the N-Sudan Platform sub-basin as evidenced by the difference in groundwater isotopic compositions across the uplift, the depletion in GRACE-derived total water storage north but not south, of the uplift, and groundwater ages that are indicative of autochthonous precipitation and recharge over the Dakhla sub-basin. Our findings provide valuable insights into optimum ways for the utilization of the NSAS

Constraints from Mesozoic siliciclastic cover rocks and satellite image analysis on the slip history of regional E-W faults in the southeast Western Desert, Egypt

NASA Astrophysics Data System (ADS)

Tewksbury, Barbara J.; Mehrtens, Charlotte J.; Gohlke, Steven A.; Tarabees, Elhamy A.; Hogan, John P.

2017-12-01

In the southeast Western Desert of Egypt, a prominent set of E-W faults and co-located domes and basins involve sedimentary cover rock as young as the early Eocene. Although earlier Mesozoic slip on faults in southern Egypt has been widely mentioned in the literature and attributed to repeated reactivation of basement faults, evidence is indirect and based on the idea that regional stresses associated with tectonic events in the Syrian Arc would likely have reactivated basement faults in south Egypt in dextral strike slip during the Mesozoic as well as the Cenozoic. Here, we present direct evidence from the rock record for the sequence of development of features along these faults. Southwest of Aswan, a small structural dome in Mesozoic Nubia facies rocks occurs where the Seiyal Fault bends northward from west to east. The dome is cut by strands of the Seiyal Fault and a related set of cataclastic deformation bands showing dominantly right lateral strike slip, as well as by younger calcite veins with related patchy poikilotopic cement. High resolution satellite image analysis of the remote southwest Kharga Valley shows a similar sequence of events: older structural domes and basins located where E-W faults bend northward from west to east, right lateral offset of domes and basins along the E-W faults, and two sets of deformation band faults that lack co-located domes and basins. We suggest that field data, image analysis, and burial depth estimates are best explained by diachronous development of features along the E-W fault system. We propose that Late Mesozoic right lateral strike slip produced domes and basins in Nubia facies rocks in stepover regions above reactivated basement faults. We further suggest that the extensively linked segments of the E-W fault system in Nubia facies rocks, plus the deformation band systems, formed during the late Eocene when basement faults were again reactivated in dominantly right lateral strike slip.

Recharge sources and geochemical evolution of groundwater in the Quaternary aquifer at Atfih area, the northeastern Nile Valley, Egypt

NASA Astrophysics Data System (ADS)

El-Sayed, Salah Abdelwahab; Morsy, Samah M.; Zakaria, Khalid M.

2018-06-01

This study addresses the topic of recharge sources and evolution of groundwater in the Atfih area situated in the northeastern part of the Nile Valley, Egypt. Inventory of water wells and collection of groundwater and surface water samples have been achieved. Water samples are analyzed for major ions according to the American Society for Testing and Materials and for the environmental isotopes analysis (oxygen-18 and deuterium) by using a Triple Liquid Isotopic Water Analyzer (Los Gatos). The groundwater is available from the Quaternary aquifer formed mainly of graded sand and gravel interbedded with clay lenses. The hydrogeologic, hydrogeochemical and isotopic investigations indicate the hydrodynamic nature of the aquifer, where different flow paths, recharge sources and evolution mechanisms are distinguished. The directions of groundwater flow are from E, W and S directions suggesting the contribution from Nile River, the Eocene aquifer and the Nile basin, respectively. The groundwater altitudes range from 13 m (MSL) to 44 m (MSL). The hydraulic gradient varies between 0.025 and 0.0015. The groundwater is alkaline (pH > 7) and has salinity ranging from fresh to brackish water (TDS between 528 mg/l and 6070 mg/l). The observed wide range in the ionic composition and water types reflects the effect of different environmental and geological conditions through which the water has flowed. The isotopic compositions of groundwater samples vary between -14.13‰ and +23.56 for δD and between - 2.91‰ and +3.10 for δ18O. The isotopic data indicates that the Quaternary aquifer receive recharge from different sources including the Recent Nile water, surplus irrigation water, old Nile water before the construction of Aswan High Dam, surface runoff of local rains and Eocene aquifer. Evaporation, water rock interaction and mixing between different types of waters are the main processes in the groundwater evolution. Major suggestions are presented to develop the aquifer

High Tech High.

ERIC Educational Resources Information Center

Hardy, Lawrence

2001-01-01

In an era of high-stakes testing and prescriptive teaching styles, a San Diego charter high school embraces project learning, multilevel classrooms, and video portfolios of student work. The school lacks dining, music, and athletic facilities, but features hefty teacher salaries, student freedom, and real-world problem solving. (MLH)

High-field/high-pressure ESR

NASA Astrophysics Data System (ADS)

Sakurai, T.; Okubo, S.; Ohta, H.

2017-07-01

We present a historical review of high-pressure ESR systems with emphasis on our recent development of a high-pressure, high-field, multi-frequency ESR system. Until 2000, the X-band system was almost established using a resonator filled with dielectric materials or a combination of the anvil cell and dielectric resonators. Recent developments have shifted from that in the low-frequency region, such as X-band, to that in multi-frequency region. High-pressure, high-field, multi-frequency ESR systems are classified into two types. First are the systems that use a vector network analyzer or a quasi-optical bridge, which have high sensitivity but a limited frequency region; the second are like our system, which has a very broad frequency region covering the THz region, but lower sensitivity. We will demonstrate the usefulness of our high-pressure ESR system, in addition to its experimental limitations. We also discuss the recent progress of our system and future plans.

High PRF high current switch

DOEpatents

Moran, Stuart L.; Hutcherson, R. Kenneth

1990-03-27

A triggerable, high voltage, high current, spark gap switch for use in pu power systems. The device comprises a pair of electrodes in a high pressure hydrogen environment that is triggered by introducing an arc between one electrode and a trigger pin. Unusually high repetition rates may be obtained by undervolting the switch, i.e., operating the trigger at voltages much below the self-breakdown voltage of the device.

Project Georgia High School/High Tech

NASA Technical Reports Server (NTRS)

2000-01-01

The High School/High Tech initiative of the President's Committee on Employment of Disabilities, Georgia's application of the collaborative "Georgia Model" and NASA's commitment of funding have shown that opportunities for High School/High Tech students are unlimited. In Georgia, the partnership approach to meeting the needs of this program has opened doors previously closed. As the program grows and develops, reflecting the needs of our students and the marketplace, more opportunities will be available. Our collaboratives are there to provide these opportunities and meet the challenge of matching our students with appropriate education and career goals. Summing up the activities and outcomes of Project Georgia High School/High Tech is not difficult. Significant outcomes have already occurred in the Savannah area as a result of NASA's grant. The support of NASA has enabled Georgia Committee to "grow" High School/High Tech throughout the region-and, by example, the state. The success of the Columbus pilot project has fostered the proliferation of projects, resulting in more than 30 Georgia High School High Tech programs-with eight in the Savannah area.

Project Georgia High School/High Tech

NASA Technical Reports Server (NTRS)

2000-01-01

Georgia High School/High Tech has been developing a suggested curriculum for use in its programs. The purpose of this instructional material is to provide a basic curriculum format for teachers of High School/High Tech students. The curriculum is designed to implement QCC classroom instruction that encourages career development in technological fields through post-secondary education, paid summer internships, and exposure to experiences in high technology.

High-current, high-frequency capacitors

NASA Technical Reports Server (NTRS)

Renz, D. D.

1983-01-01

The NASA Lewis high-current, high-frequency capacitor development program was conducted under a contract with Maxwell Laboratories, Inc., San Diego, California. The program was started to develop power components for space power systems. One of the components lacking was a high-power, high-frequency capacitor. Some of the technology developed in this program may be directly usable in an all-electric airplane. The materials used in the capacitor included the following: the film is polypropylene, the impregnant is monoisopropyl biphenyl, the conductive epoxy is Emerson and Cuming Stycast 2850 KT, the foil is aluminum, the case is stainless steel (304), and the electrode is a modified copper-ceramic.

Highly Accreting Quasars at High Redshift

NASA Astrophysics Data System (ADS)

Martínez-Aldama, Mary L.; Del Olmo, Ascensión; Marziani, Paola; Sulentic, Jack W.; Negrete, C. Alenka; Dultzin, Deborah; Perea, Jaime; D'Onofrio, Mauro

2017-12-01

We present preliminary results of a spectroscopic analysis for a sample of type 1 highly accreting quasars (LLedd>0.2) at high redshift, z 2-3. The quasars were observed with the OSIRIS spectrograph on the GTC 10.4 m telescope located at the Observatorio del Roque de los Muchachos in La Palma. The highly accreting quasars were identified using the 4D Eigenvector 1 formalism, which is able to organize type 1 quasars over a broad range of redshift and luminosity. The kinematic and physical properties of the broad line region have been derived by fitting the profiles of strong UV emission lines such as AlIII, SiIII and CIII. The majority of our sources show strong blueshifts in the high-ionization lines and high Eddington ratios which are related with the productions of outflows. The importance of highly accreting quasars goes beyond a detailed understanding of their physics: their extreme Eddington ratio makes them candidates standard candles for cosmological studies.

Dental affinities of the C-group inhabitants of Hierakonpolis, Egypt: Nubian, Egyptian, or both?

PubMed

Irish, J D; Friedman, R

2010-04-01

By c. 2050 BC a small community of C-Group Nubians was present deep within Egyptian territory at the city of Hierakonpolis. Their descendants stayed for the next 400 years. Today, the site of Hierakonpolis, 113 km north of Aswan, is known for its Egyptian deposits; however, it also contains a C-Group cemetery, which documents the northernmost occurrence of this culture. Sixty skeletons were excavated. Tombs feature Nubian architecture and goods, including leather garments, although the use of Egyptian mortuary practices and artifacts increased through time. Dates range from the early 11th Dynasty into the Second Intermediate period. During this time the Egyptian empire occupied Lower Nubia, and their state ideology vilified Nubians. Yet, at least in death, the C-Group inhabitants of Hierakonpolis proudly displayed their cultural heritage. Beyond discerning the reason(s) for their presence at the site (e.g., mercenaries, leather-workers, entertainers?), the focus of this report is to estimate their biological affinity. Were they akin to other Nubians, Egyptians, or both? And, was increasing 'Egyptianization' evident in the mortuary ritual accompanied by concomitant genetic influence? To address these queries, up to 36 dental morphological traits in the recovered individuals were compared to those in 26 regional comparative samples. The most influential traits were identified and phenetic affinities were calculated using the mean measure of divergence and other multivariate analyses. Assuming phenetic similarity provides an estimate of genetic relatedness, these affinities suggest the individuals comprising the C-Group sample were, and remained Nubian during their tenure at Hierakonpolis. Copyright 2010 Elsevier GmbH. All rights reserved.

High-Power, High-Temperature Superconductor Technology Development

NASA Technical Reports Server (NTRS)

Bhasin, Kul B.

2005-01-01

Since the first discovery of high-temperature superconductors (HTS) 10 years ago, the most promising areas for their applications in microwave systems have been as passive components for communication systems. Soon after the discovery, experiments showed that passive microwave circuits made from HTS material exceeded the performance of conventional devices for low-power applications and could be 10 times as small or smaller. However, for superconducting microwave components, high-power microwave applications have remained elusive until now. In 1996, DuPont and Com Dev Ltd. developed high-power superconducting materials and components for communication applications under a NASA Lewis Research Center cooperative agreement, NCC3-344 "High Power High Temperature Superconductor (HTS) Technology Development." The agreement was cost shared between the Defense Advanced Research Projects Agency's (DARPA) Technology Reinvestment Program Office and the two industrial partners. It has the following objectives: 1) Material development and characterization for high-power HTS applications; 2) Development and validation of generic high-power microwave components; 3) Development of a proof-of-concept model for a high-power six-channel HTS output multiplexer.

High-voltage, high-current, solid-state closing switch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Focia, Ronald Jeffrey

2017-08-22

A high-voltage, high-current, solid-state closing switch uses a field-effect transistor (e.g., a MOSFET) to trigger a high-voltage stack of thyristors. The switch can have a high hold-off voltage, high current carrying capacity, and high time-rate-of-change of current, di/dt. The fast closing switch can be used in pulsed power applications.

High-absorptance high-emittance anodic coating

NASA Technical Reports Server (NTRS)

Le, Huong Giang (Inventor); Chesterfield, John L. (Inventor)

1998-01-01

A colored anodic coating for use on surfaces of substrates, e.g. aluminum substrates in which it is desirable to maintain a high solar absorptance (a) and a high infrared emittance (e), particularly in low earth orbit space environments. This anodic coating is preferably a dark colored coating, and even more preferably a black coating. This coating allows a touch temperature within an acceptable design range to preclude burning of an astronaut in case of contact, but also allows a solar radiation absorption in an amount such that an a/e ratio of unity is achieved. The coating of the invention comprises a first layer in the form of an acid anodized colored anodic layer for achieving a high solar absorptance and a second or high emittance layer in the form of a clear acid anodized layer for achieving a high emittance. The entire coating is quite thin, e.g. 1-2 mils and is quite stable in a hostile space environment of the type encountered in a low earth orbit. The coating is obtained by first creating the high emittance clear anodized coating on the metal surface followed by anodizing using a colored anodizing process.

High-absorptance high-emittance anodic coating

NASA Technical Reports Server (NTRS)

Le, Huong Giang (Inventor); Chesterfield, John L. (Inventor)

1999-01-01

A colored anodic coating for use on surfaces of substrates, e.g. aluminum substrates in which it is desirable to maintain a high solar absorptance (.alpha.) and a high infrared emittance (.epsilon.), particularly in low earth orbit space environments. This anodic coating is preferably a dark colored coating, and even more preferably a black coating. This coating allows a touch temperature within an acceptable design range to preclude burning of an astronaut in case of contact, but also allows a solar radiation absorption in an amount such that an .alpha./.epsilon. ratio of unity is achieved. The coating of the invention comprises a first layer in the form of an acid anodized colored anodic layer for achieving a high solar absorptance and a second or high emittance layer in the form of a clear acid anodized layer for achieving a high emittance. The entire coating is quite thin, e.g. 1-2 mils and is quite stable in a hostile space environment of the type encountered in a low earth orbit. The coating is obtained by first creating the high emittance clear anodized coating on the metal surface followed by anodizing using a colored anodizing process.

High- and low-temperature-stable thermite composition for producing high-pressure, high-velocity gases

DOEpatents

Halcomb, Danny L.; Mohler, Jonathan H.

1990-10-16

A high- and low-temperature-stable thermite composition for producing high-pressure and high-velocity gases comprises an oxidizable metal, an oxidizing reagent, and a high-temperature-stable gas-producing additive selected from the group consisting of metal carbides and metal nitrides.

High-Flying High-Poverty Schools

ERIC Educational Resources Information Center

American Educator, 2013

2013-01-01

In discussing socioeconomic integration before audiences, the author is frequently asked: What about high-poverty schools that do work? Don't they suggest that economic segregation isn't much of a problem after all? High-poverty public schools that beat the odds paint a heartening story that often attracts considerable media attention. In 2000,…

High-frequency, high-intensity photoionization

NASA Astrophysics Data System (ADS)

Reiss, H. R.

1996-02-01

Two analytical methods for computing ionization by high-frequency fields are compared. Predicted ionization rates compare well, but energy predictions for the onset of ionization differ radically. The difference is shown to arise from the use of a transformation in one of the methods that alters the zero from which energy is measured. This alteration leads to an apparent energy threshold for ionization that can, especially in the stabilization regime, differ strongly from the laboratory measurement. It is concluded that channel closings in intense-field ionization can occur at high as well as low frequencies. It is also found that the stabilization phenomenon at high frequencies, very prominent for hydrogen, is absent in a short-range potential.

HIGH-TEMPERATURE AND HIGH-PRESSURE PARTICULATE CONTROL REQUIREMENTS

EPA Science Inventory

The report reviews and evaluates high-temperature and high-pressure particulate cleanup requirements of existing and proposed energy processes. The study's aims are to define specific high-temperature and high-pressure particle removal problems, to indicate potential solutions, a...

Quenching ilmenite with a high-temperature and high-pressure phase using super-high-energy ball milling.

PubMed

Hashishin, Takeshi; Tan, Zhenquan; Yamamoto, Kazuhiro; Qiu, Nan; Kim, Jungeum; Numako, Chiya; Naka, Takashi; Valmalette, Jean Christophe; Ohara, Satoshi

2014-04-25

The mass production of highly dense oxides with high-temperature and high-pressure phases allows us to discover functional properties that have never been developed. To date, the quenching of highly dense materials at the gramme-level at ambient atmosphere has never been achieved. Here, we provide evidence of the formation of orthorhombic Fe2TiO4 from trigonal FeTiO3 as a result of the high-temperature (>1250 K) and high-pressure (>23 GPa) condition induced by the high collision energy of 150 gravity generated between steel balls. Ilmenite was steeply quenched by the surrounding atmosphere, when iron-rich ilmenite (Fe2TiO4) with a high-temperature and high-pressure phase was formed by planetary collisions and was released from the collision points between the balls. Our finding allows us to infer that such intense planetary collisions induced by high-energy ball milling contribute to the mass production of a high-temperature and high-pressure phase.

Quenching ilmenite with a high-temperature and high-pressure phase using super-high-energy ball milling

PubMed Central

Hashishin, Takeshi; Tan, Zhenquan; Yamamoto, Kazuhiro; Qiu, Nan; Kim, Jungeum; Numako, Chiya; Naka, Takashi; Valmalette, Jean Christophe; Ohara, Satoshi

2014-01-01

The mass production of highly dense oxides with high-temperature and high-pressure phases allows us to discover functional properties that have never been developed. To date, the quenching of highly dense materials at the gramme-level at ambient atmosphere has never been achieved. Here, we provide evidence of the formation of orthorhombic Fe2TiO4 from trigonal FeTiO3 as a result of the high-temperature (>1250 K) and high-pressure (>23 GPa) condition induced by the high collision energy of 150 gravity generated between steel balls. Ilmenite was steeply quenched by the surrounding atmosphere, when iron-rich ilmenite (Fe2TiO4) with a high-temperature and high-pressure phase was formed by planetary collisions and was released from the collision points between the balls. Our finding allows us to infer that such intense planetary collisions induced by high-energy ball milling contribute to the mass production of a high-temperature and high-pressure phase. PMID:24763088

High-efficiency, broad band, high-damage threshold high-index gratings for femtosecond pulse compression.

PubMed

Canova, Frederico; Clady, Raphael; Chambaret, Jean-Paul; Flury, Manuel; Tonchev, Svtelen; Fechner, Renate; Parriaux, Olivier

2007-11-12

High efficiency, broad-band TE-polarization diffraction over a wavelength range centered at 800 nm is obtained by high index gratings placed on a non-corrugated mirror. More than 96% efficiency wide band top-hat diffraction efficiency spectra, as well as more than 1 J/cm(2) damage threshold under 50 fs pulses are demonstrated experimentally. This opens the way to high-efficiency Chirped Pulse Amplification for high average power laser machining by means of all-dielectric structures as well as for ultra-short high energy pulses by means of metal-dielectric structures.

Project Synopsis for High School/High Tech

NASA Technical Reports Server (NTRS)

1997-01-01

To help increase the diversity of workers at NASA centers it is necessary to provide students with disabilities the opportunities to explore careers in high technology. HIGH SCHOOL/HIGH TECH, an enrichment program, pioneered at Goddard Space Flight Center, successfully introduces students with disabilities to high tech careers. This community-based partnership serves as a model for three additional NASA sites-Ames Research Center, Johnson Space Flight Center, and Lewis Research Center. For a three year period beginning August 15, 1995, provide financial and technical support to a local agency in each NASA center area which serves persons with disabilities to enable a High School/High Tech program to develop and stand alone. Each project will develop a basis of cooperation with Ames, Johnson, and Lewis as well as a variety of community groups including the public schools, high tech employers, post-secondary education and training programs, rehabilitation agencies, and community economic development organizations. Throughout the startup period and thereafter, local youths with disabilities will have early exposure to professions in mathematics, science, and technology-related fields. This exposure will be multifaceted to insure adequate opportunity for realistic career exploration so these youths have an opportunity to test their interests and abilities. The exposure will be presented in the most supportive environment that is feasible.

High Temperature, High Power Piezoelectric Composite Transducers

PubMed Central

Lee, Hyeong Jae; Zhang, Shujun; Bar-Cohen, Yoseph; Sherrit, StewarT.

2014-01-01

Piezoelectric composites are a class of functional materials consisting of piezoelectric active materials and non-piezoelectric passive polymers, mechanically attached together to form different connectivities. These composites have several advantages compared to conventional piezoelectric ceramics and polymers, including improved electromechanical properties, mechanical flexibility and the ability to tailor properties by using several different connectivity patterns. These advantages have led to the improvement of overall transducer performance, such as transducer sensitivity and bandwidth, resulting in rapid implementation of piezoelectric composites in medical imaging ultrasounds and other acoustic transducers. Recently, new piezoelectric composite transducers have been developed with optimized composite components that have improved thermal stability and mechanical quality factors, making them promising candidates for high temperature, high power transducer applications, such as therapeutic ultrasound, high power ultrasonic wirebonding, high temperature non-destructive testing, and downhole energy harvesting. This paper will present recent developments of piezoelectric composite technology for high temperature and high power applications. The concerns and limitations of using piezoelectric composites will also be discussed, and the expected future research directions will be outlined. PMID:25111242

High speed micromachining with high power UV laser

NASA Astrophysics Data System (ADS)

Patel, Rajesh S.; Bovatsek, James M.

2013-03-01

Increasing demand for creating fine features with high accuracy in manufacturing of electronic mobile devices has fueled growth for lasers in manufacturing. High power, high repetition rate ultraviolet (UV) lasers provide an opportunity to implement a cost effective high quality, high throughput micromachining process in a 24/7 manufacturing environment. The energy available per pulse and the pulse repetition frequency (PRF) of diode pumped solid state (DPSS) nanosecond UV lasers have increased steadily over the years. Efficient use of the available energy from a laser is important to generate accurate fine features at a high speed with high quality. To achieve maximum material removal and minimal thermal damage for any laser micromachining application, use of the optimal process parameters including energy density or fluence (J/cm2), pulse width, and repetition rate is important. In this study we present a new high power, high PRF QuasarR 355-40 laser from Spectra-Physics with TimeShiftTM technology for unique software adjustable pulse width, pulse splitting, and pulse shaping capabilities. The benefits of these features for micromachining include improved throughput and quality. Specific example and results of silicon scribing are described to demonstrate the processing benefits of the Quasar's available power, PRF, and TimeShift technology.

High-Power, High-Thrust Ion Thruster (HPHTion)

NASA Technical Reports Server (NTRS)

Peterson, Peter Y.

2015-01-01

Advances in high-power photovoltaic technology have enabled the possibility of reasonably sized, high-specific power solar arrays. At high specific powers, power levels ranging from 50 to several hundred kilowatts are feasible. Ion thrusters offer long life and overall high efficiency (typically greater than 70 percent efficiency). In Phase I, the team at ElectroDynamic Applications, Inc., built a 25-kW, 50-cm ion thruster discharge chamber and fabricated a laboratory model. This was in response to the need for a single, high-powered engine to fill the gulf between the 7-kW NASA's Evolutionary Xenon Thruster (NEXT) system and a notional 25-kW engine. The Phase II project matured the laboratory model into a protoengineering model ion thruster. This involved the evolution of the discharge chamber to a high-performance thruster by performance testing and characterization via simulated and full beam extraction testing. Through such testing, the team optimized the design and built a protoengineering model thruster. Coupled with gridded ion thruster technology, this technology can enable a wide range of missions, including ambitious near-Earth NASA missions, Department of Defense missions, and commercial satellite activities.

High School/High Tech Program Guide: An Implementation Guide for High School/High Tech Program Coordinators. Promoting Careers in Science and Technology for High School Students with Disabilities.

ERIC Educational Resources Information Center

Office of Disability Employment Policy (DOL), Washington, DC.

This implementation guide is intended to assist educators in planning, establishing, building, and managing a High School/High Tech project for high school students with disabilities. The program is designed to develop career opportunities, provide activities that will spark an interest in high technology fields, and encourage students to pursue…

Discussion on the application of high additional value of high purity and high quality direct reduced iron

NASA Astrophysics Data System (ADS)

Yue, Chongfeng; Bai, Lu; Hong, Yicheng; Xu, Lijun

2018-03-01

The high purity and high quality direct reduced iron(DRI) products which were produced by high grade and high quality iron powder, with a high grade and low impurity characteristics. This article introduced the application of high purity and high quality DRI in the fields of amorphous base material, atomized iron powder, powder superalloy, high purity and ultra-low carbon special metallurgy products, precision casting, super alloy and various iron-based alloys. It provides a reference for the high added value utilization of DRI.

High pressure, high current, low inductance, high reliability sealed terminals

DOEpatents

Hsu, John S [Oak Ridge, TN; McKeever, John W [Oak Ridge, TN

2010-03-23

The invention is a terminal assembly having a casing with at least one delivery tapered-cone conductor and at least one return tapered-cone conductor routed there-through. The delivery and return tapered-cone conductors are electrically isolated from each other and positioned in the annuluses of ordered concentric cones at an off-normal angle. The tapered cone conductor service can be AC phase conductors and DC link conductors. The center core has at least one service conduit of gate signal leads, diagnostic signal wires, and refrigerant tubing routed there-through. A seal material is in direct contact with the casing inner surface, the tapered-cone conductors, and the service conduits thereby hermetically filling the interstitial space in the casing interior core and center core. The assembly provides simultaneous high-current, high-pressure, low-inductance, and high-reliability service.

Development of high strength, high temperature ceramics

NASA Technical Reports Server (NTRS)

Hall, W. B.

1982-01-01

Improvement in the high-pressure turbopumps, both fuel and oxidizer, in the Space Shuttle main engine were considered. The operation of these pumps is limited by temperature restrictions of the metallic components used in these pumps. Ceramic materials that retain strength at high temperatures and appear to be promising candidates for use as turbine blades and impellers are discussed. These high strength materials are sensitive to many related processing parameters such as impurities, sintering aids, reaction aids, particle size, processing temperature, and post thermal treatment. The specific objectives of the study were to: (1) identify and define the processing parameters that affect the properties of Si3N4 ceramic materials, (2) design and assembly equipment required for processing high strength ceramics, (3) design and assemble test apparatus for evaluating the high temperature properties of Si3N4, and (4) conduct a research program of manufacturing and evaluating Si3N4 materials as applicable to rocket engine applications.

High-energy, high-rate materials processing

NASA Astrophysics Data System (ADS)

Marcus, H. L.; Bourell, D. L.; Eliezer, Z.; Persad, C.; Weldon, W.

1987-12-01

The increasingly available range of pulsed-power, high energy kinetic storage devices, such as low-inductance pulse-forming networks, compulsators, and homopolar generators, is presently considered as a basis for industrial high energy/high rate (HEHR) processing to accomplish shock hardening, drilling, rapid surface alloying and melting, welding and cutting, transformation hardening, and cladding and surface melting in metallic materials. Time-temperature-transformation concepts furnish the basis for a fundamental understanding of the potential advantages of this direct pulsed power processing. Attention is given to the HEHR processing of a refractory molybdenum alloy, a nickel-base metallic glass, tungsten, titanium aluminides, and metal-matrix composites.

Structural Control and Groundwater Flow in the Nubian Aquifer

NASA Astrophysics Data System (ADS)

Fathy, K.; Sultan, M.; Ahmed, M.; Save, H.; Emil, M. K.; Elkaliouby, B.

2017-12-01

An integrated research approach (remote sensing, field, geophysics) was conducted to investigate the structural control on groundwater flow in large aquifers using the less studied Nubian Sandstone Aquifer System (NSAS) of NE Africa as a test site. The aquifer extends over 2.2 x 106 km2 in Egypt, Libya, Chad, and Sudan and consists of thick (> 3 kms), water-bearing, Paleozoic and Mesozoic sandstone with intercalations of Tertiary shale and clay. It is subdivided into three sub-basins (Northern Sudan Platform [NSP], Dakhla [DAS], and Kufra) that are separated by basement uplifts (e.g., E-W trending Uweinat-Aswan uplift that separates DAS from the NSP). Aquifer recharge occurs in the south (NSP and southern Kufra) where the aquifer is unconfined and precipitation is high (Average Annual Precipitation [AAP]: 117 mm/yr.) and discharge is concentrated in the north (DAS and northern Kufra). Our approach is a three-fold exercise. Firstly, we compared GOCE-based Global Geopotential Models (GGMs) to terrestrial gravity anomalies for 21262 sites to select the optimum model for deriving Bouguer gravity anomalies. Secondly, structures and uplifts were mapped using hill shade images and their extension in the subsurface were mapped using the Eigen_6C4 model-derived Bouguer anomalies and their Tilt Derivative products (TDR). Thirdly, hydrological analysis was conducted using GRACE CSR 1° x 1° mascon solutions to investigate the mass variations in relation to the mapped structures. Our findings include: (1) The Eigen-6C4 is the optimum model having the lowest deviation (9.122 mGal) from the terrestrial gravity anomalies; (2) the surface expressions of structures matched fairly well with their postulated extensions in the subsurface; (3) identified fault systems include: Red Sea rift-related N-S to NW-SE trending grabens formed by reactivating basement structures during Red Sea opening and Syrian arc-related NE-SW trending dextral shear systems; (4) TWS patterns are uniform

The modern Nile sediment system: Processes and products

NASA Astrophysics Data System (ADS)

Garzanti, Eduardo; Andò, Sergio; Padoan, Marta; Vezzoli, Giovanni; El Kammar, Ahmed

2015-12-01

We trace compositional changes of Nile sediments for 7400 km, from their sources in equatorial rift highlands of Burundi and Rwanda to their sink in the Mediterranean Sea. All chemical and physical controls on sediment petrography, mineralogy and geochemistry, including weathering, grain-size, hydraulic sorting, mechanical breakdown, anthropic impact, mixing and recycling are investigated in detail. The Nile course is controlled along its entire length by the East African-Red Sea Rift. In this anorogenic setting, detritus is derived in various proportions from volcanic fields associated with tectonic extension (Anorogenic Volcanic provenance) and from igneous, metamorphic and sedimentary rocks uplifted on the rift shoulders or exposed on the craton (Continental Block provenance). The entire spectrum of such detrital signatures is displayed in the Nile catchment. Volcaniclastic Atbara sand is generated by focused erosion of the Ethiopian basaltic plateau in semiarid climate, whereas quartzose White Nile sand reflects low erosion rates, extensive weathering and sediment trapping in lakes and swamps at equatorial to subequatorial latitudes. In the main Nile, as in its main tributary the Blue Nile, suspended load is volcaniclastic, whereas feldspatho-quartzose bedload is derived largely from basement sources, with fine to medium-grained eolian sand added along the lower course. Mixing of detrital populations with different provenance and grain size is reflected in diverse violations of settling-equivalence relationships in fluvial and deltaic sediments. Sediment delivery from Sudan has been cut off after closure of the Aswan High Dam and accelerated erosion of deltaic cusps is leading to local formation of placer lags dominated by ultradense Fe-Ti-Cr oxides, but mineralogical changes caused by man's radical modification of fluvial regimes have been minor so far. In beaches of Sinai, Gaza and Israel, the Nile volcaniclastic trace gets progressively diluted by quartzose

Rainfall Estimation over the Nile Basin using an Adapted Version of the SCaMPR Algorithm

NASA Astrophysics Data System (ADS)

Habib, E. H.; Kuligowski, R. J.; Elshamy, M. E.; Ali, M. A.; Haile, A.; Amin, D.; Eldin, A.

2011-12-01

Management of Egypt's Aswan High Dam is critical not only for flood control on the Nile but also for ensuring adequate water supplies for most of Egypt since rainfall is scarce over the vast majority of its land area. However, reservoir inflow is driven by rainfall over Sudan, Ethiopia, Uganda, and several other countries from which routine rain gauge data are sparse. Satellite-derived estimates of rainfall offer a much more detailed and timely set of data to form a basis for decisions on the operation of the dam. A single-channel infrared algorithm is currently in operational use at the Egyptian Nile Forecast Center (NFC). This study reports on the adaptation of a multi-spectral, multi-instrument satellite rainfall estimation algorithm (Self-Calibrating Multivariate Precipitation Retrieval, SCaMPR) for operational application over the Nile Basin. The algorithm uses a set of rainfall predictors from multi-spectral Infrared cloud top observations and self-calibrates them to a set of predictands from Microwave (MW) rain rate estimates. For application over the Nile Basin, the SCaMPR algorithm uses multiple satellite IR channels recently available to NFC from the Spinning Enhanced Visible and Infrared Imager (SEVIRI). Microwave rain rates are acquired from multiple sources such as SSM/I, SSMIS, AMSU, AMSR-E, and TMI. The algorithm has two main steps: rain/no-rain separation using discriminant analysis, and rain rate estimation using stepwise linear regression. We test two modes of algorithm calibration: real-time calibration with continuous updates of coefficients with newly coming MW rain rates, and calibration using static coefficients that are derived from IR-MW data from past observations. We also compare the SCaMPR algorithm to other global-scale satellite rainfall algorithms (e.g., 'Tropical Rainfall Measuring Mission (TRMM) and other sources' (TRMM-3B42) product, and the National Oceanographic and Atmospheric Administration Climate Prediction Center (NOAA

High concentration agglomerate dynamics at high temperatures.

PubMed

Heine, M C; Pratsinis, S E

2006-11-21

The dynamics of agglomerate aerosols are investigated at high solids concentrations that are typical in industrial scale manufacture of fine particles (precursor mole fraction larger than 10 mol %). In particular, formation and growth of fumed silica at such concentrations by chemical reaction, coagulation, and sintering is simulated at nonisothermal conditions and compared to limited experimental data and commercial product specifications. Using recent chemical kinetics for silica formation by SiCl4 hydrolysis and neglecting aerosol polydispersity, the evolution of the diameter of primary particles (specific surface area, SSA), hard- and soft-agglomerates, along with agglomerate effective volume fraction (volume occupied by agglomerate) is investigated. Classic Smoluchowski theory is fundamentally limited for description of soft-agglomerate Brownian coagulation at high solids concentrations. In fact, these high concentrations affect little the primary particle diameter (or SSA) but dominate the soft-agglomerate diameter, structure, and volume fraction, leading to gelation consistent with experimental data. This indicates that restructuring and fragmentation should affect product particle characteristics during high-temperature synthesis of nanostructured particles at high concentrations in aerosol flow reactors.

Compact high voltage, high peak power, high frequency transformer for converter type modulator applications.

PubMed

Reghu, T; Mandloi, V; Shrivastava, Purushottam

2016-04-01

The design and development of a compact high voltage, high peak power, high frequency transformer for a converter type modulator of klystron amplifiers is presented. The transformer has been designed to operate at a frequency of 20 kHz and at a flux swing of ±0.6 T. Iron (Fe) based nanocrystalline material has been selected as a core for the construction of the transformer. The transformer employs a specially designed solid Teflon bobbin having 120 kV insulation for winding the high voltage secondary windings. The flux swing of the core has been experimentally found by plotting the hysteresis loop at actual operating conditions. Based on the design, a prototype transformer has been built which is per se a unique combination of high voltage, high frequency, and peak power specifications. The transformer was able to provide 58 kV (pk-pk) at the secondary with a peak power handling capability of 700 kVA. The transformation ratio was 1:17. The performance of the transformer is also presented and discussed.

High temperature- and high pressure-processed garlic improves lipid profiles in rats fed high cholesterol diets.

PubMed

Sohn, Chan Wok; Kim, Hyunae; You, Bo Ram; Kim, Min Jee; Kim, Hyo Jin; Lee, Ji Yeon; Sok, Dai-Eun; Kim, Jin Hee; Lee, Kun Jong; Kim, Mee Ree

2012-05-01

Garlic protects against degenerative diseases such as hyperlipidemia and cardiovascular diseases. However, raw garlic has a strong pungency, which is unpleasant. In this study, we examined the effect of high temperature/high pressure-processed garlic on plasma lipid profiles in rats. Sprague-Dawley rats were fed a normal control diet, a high cholesterol (0.5% cholesterol) diet (HCD) only, or a high cholesterol diet supplemented with 0.5% high temperature/high pressure-processed garlic (HCP) or raw garlic (HCR) for 10 weeks. The body weights of the rats fed the garlic-supplemented diets decreased, mostly because of reduced fat pad weights. Plasma levels of total cholesterol (TC), low-density lipoprotein cholesterol, and triglyceride (TG) in the HCP and HCR groups decreased significantly compared with those in the HCD group. Additionally, fecal TC and TG increased significantly in the HCP and HCR groups. It is notable that no significant differences in plasma or fecal lipid profiles were observed between the HCP and HCR groups. High temperature/high pressure-processed garlic contained a higher amount of S-allyl cysteine than raw garlic (P<.05). The results suggest that high temperature/high pressure-processed garlic may be useful as a functional food to improve lipid profiles.

High Temperature- and High Pressure-Processed Garlic Improves Lipid Profiles in Rats Fed High Cholesterol Diets

PubMed Central

Sohn, Chan Wok; Kim, Hyunae; You, Bo Ram; Kim, Min Jee; Kim, Hyo Jin; Lee, Ji Yeon; Sok, Dai-Eun; Kim, Jin Hee; Lee, Kun Jong

2012-01-01

Abstract Garlic protects against degenerative diseases such as hyperlipidemia and cardiovascular diseases. However, raw garlic has a strong pungency, which is unpleasant. In this study, we examined the effect of high temperature/high pressure-processed garlic on plasma lipid profiles in rats. Sprague–Dawley rats were fed a normal control diet, a high cholesterol (0.5% cholesterol) diet (HCD) only, or a high cholesterol diet supplemented with 0.5% high temperature/high pressure-processed garlic (HCP) or raw garlic (HCR) for 10 weeks. The body weights of the rats fed the garlic-supplemented diets decreased, mostly because of reduced fat pad weights. Plasma levels of total cholesterol (TC), low-density lipoprotein cholesterol, and triglyceride (TG) in the HCP and HCR groups decreased significantly compared with those in the HCD group. Additionally, fecal TC and TG increased significantly in the HCP and HCR groups. It is notable that no significant differences in plasma or fecal lipid profiles were observed between the HCP and HCR groups. High temperature/high pressure-processed garlic contained a higher amount of S-allyl cysteine than raw garlic (P<.05). The results suggest that high temperature/high pressure-processed garlic may be useful as a functional food to improve lipid profiles. PMID:22404600

Transfer of Natrialba asiatica B1T to Natrialba taiwanensis sp. nov. and description of Natrialba aegyptiaca sp. nov., a novel extremely halophilic, aerobic, non-pigmented member of the Archaea from Egypt that produces extracellular poly(glutamic acid).

PubMed

Hezayen, F F; Rehm, B H; Tindall, B J; Steinbüchel, A

2001-05-01

A novel extremely halophilic member of the Archaea, strain 40T, was isolated from Egypt (Aswan). This isolate requires at least 1.6 M sodium chloride for growth and exhibits optimal growth between 37 and 42 degrees C. Determination of the entire 16S rRNA gene sequence revealed the highest similarity to the type strain of Natrialba asiatica (> 99%). Polar lipid analysis indicated that strain 40T and Natrialba asiatica have essentially identical compositions, indicating that the former is a member of genus Natrialba. However, physiological and biochemical data provided evidence that Natrialba asiatica strains B1T and 172P1T, as well as strain 40T, are sufficiently different to be divided in three different species. The G+C content of strain 40T was 61.5+/-0.6 mol%. In addition, DNA-DNA hybridization data supported the placement of the isolate in a new species in the genus Natrialba, Natrialba aegyptiaca sp. nov., and indicated that Natrialba asiatica strain B1T should also be placed in a separate species, Natrialba taiwanensis sp. nov. Morphological studies of strain 40T indicated clearly that this isolate appears in three completely different cell shapes (cocci, rods, tetrads) under different conditions of growth, including different sodium chloride concentrations and different growth temperatures. Another interesting property of strain 40T is the ability to produce an extracellular polymer, which was found to be composed predominantly of glutamic acid (85% w/w), representing poly(glutamic acid), carbohydrates (12.5% w/w) and unidentified compounds (2.5% w/w). Among the Archaea, production of an extracellular polysaccharide has been described for some members of the genera Haloferax and Haloarcula.

High Standards or a High Standard of Standardness?

ERIC Educational Resources Information Center

McWilliam, Erica

2010-01-01

This paper explores the difference between "high standards" and a "high standard of standardness" of professional service provision in teacher-librarianship. That is to say, it explores the difference between a demonstrated deep commitment to 21st century learning ("high standards") and demonstrated compliance with a pre-determined checklist of…

High strength and high toughness steel

DOEpatents

Parker, Earl R.; Zackay, Victor F.

1979-01-01

A structural steel which possess both high strength and high toughness and has particular application of cryogenic uses. The steel is produced by the utilization of thermally induced phase transformation following heating in a three-phase field in iron-rich alloys of the Fe-Ni-Ti system, with a preferred composition of 12% nickel, 0.5% titanium, the remainder being iron.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-05-31

ISS017-E-008290 (31 May 2008) --- Toshka Lakes in southern Egypt are featured in this image photographed by an Expedition 17 crewmember on the International Space Station. In the late 1990s, Egypt's new manmade Toshka Lakes, fed from Lake Nasser via a new canal, grew and spilled into new basins to become four major and two smaller waterbodies extending 120 kilometers across the desert west of the Nile River in southern Egypt. Starting in 2002, astronauts have seen the lakes slowly decline, with the telltale ring of darker, moistened ground showing the previous higher water levels. The rise and fall of Toshka Lakes, and the economic development surrounding the region, are dependent on climate fluctuations and water agreements with upstream countries that, in turn, determine the long-term water flow in the lower Nile. This view, covering a distance of 11.3 kilometers from bottom to top, shows shoreline detail of the third large lake. Lake water appears deep blue to blue-green, and parallel with the shoreline is a wide brown zone which was under water until 2002. Most of the bright yellow sand dunes in the view are re-emerging as the lake level drops, most outlined visibly by thin wet margins. Still-submerged dunes can be seen as small gray blebs offshore (left center). The summit of the biggest horn-shaped dune (top left) was an island more than 5 kilometers off shore in images from 2001. The dune pattern gives a strong sense of dune migration southwards, from top left towards lower right (horns of crescent dunes point in the direction of dune movement). Dominant northerly winds drive the dunes southward, except, of course, when they are under water.

Characterization of three commercial Y-TZP ceramics produced for their high-translucency, high-strength and high-surface area.

PubMed

Tong, Hui; Tanaka, Carina B; Kaizer, Marina R; Zhang, Yu

2016-01-01

Developing yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) with high strength and translucency could significantly widen the clinical indications of monolithic zirconia restorations. This study investigates the mechanical and optical properties of three Y-TZP ceramics: High-Translucency, High-Strength and High-Surface Area. The four-point bending strengths (mean ± standard error) for the three Y-TZP ceramics ( n = 10) were 990 ± 39, 1416 ± 33 and 1076 ± 32 MPa for High-Translucency, High-Strength and High-Surface Area, respectively. The fracture toughness values (mean ± standard error) for the three zirconias ( n = 10) were 3.24 ± 0.10, 3.63 ± 0.12 and 3.21 ± 0.14 MPa m 1/2 for High-Translucency, High-Strength and High-Surface Area, respectively. Both strength and toughness values of High-Strength zirconia were significantly higher than High-Surface Area and High-Translucency zirconias. Translucency parameter values of High-Translucency zirconia were considerably higher than High-Strength and High-Surface Area zirconias. However, all three zirconias became essentially opaque when their thickness reached 1 mm or greater. Our findings suggest that there exists a delicate balance between mechanical and optical properties of the current commercial Y-TZP ceramics.

Petrogenesis of high-Ti and low-Ti basalts: high-pressure and high-temperature experimental study

NASA Astrophysics Data System (ADS)

Yang, J.; WANG, C.; Jin, Z.

2017-12-01

Geochemical and petrological studies have revealed the existence of high-Ti and low-Ti basalts in large igneous provinces. However, the petrogenesis of them are still under debate. Several different mechanisms have been proposed: (1) the high-Ti basalts are formed by the melting of mantle plume containing recycled oceanic crust or delaminated lower crust (Spandler et al., 2008) while low-Ti basalts are formed by the melting of subcontinental lithospheric mantle (Xiao et al., 2004); (2) both of them are from mantle plume or asthenospheric source, but the production of high-Ti basalts are associated with the thick lithosphere and relevant low degrees of melting while the low-Ti basalts are controlled by the thin lithosphere with high degrees of melting (Arndt et al., 1993; Xu et al., 2001). Almost all authors emphasize the role of partial melting but less discuss the crystallization differentiation process. The low Mg# (< 0.7) of these basalts provides that they are far away from direct melting of mantle peridotite. In addition, seismic data indicate unusually high seismic velocities bodies beneath LIPs which explained by the fractionated cumulates from picritic magmas (Farnetani et al., 1996). Therefore, we believed that the crystallization differentiation process might play a more significant role in the genesis of high-Ti and low-Ti basalts. In order to investigate the generation of these basalts, a series of high pressure and high temperature partial crystallization experiments were performed by using piston-cylinder and multi-anvil press at pressures of 1.5, 3.0 and 5.0 GPa and a temperature range of 1200-1700°. Two synthetic picrite glass with different chemical compositions were used as starting materials. Our experimental results show that Ti is preferred to be concentrated in the residual melt during crystallization differentiation. For the same melt fraction, the residual melt of higher pressure experiments has relatively higher TiO2 concentration and

Pulsed-High Field/High-Frequency EPR Spectroscopy

NASA Astrophysics Data System (ADS)

Fuhs, Michael; Moebius, Klaus

Pulsed high-field/high-frequency electron paramagnetic resonance (EPR) spectroscopy is used to disentangle many kinds of different effects often obscured in continuous wave (cw) EPR spectra at lower magnetic fields/microwave frequencies. While the high magnetic field increases the resolution of G tensors and of nuclear Larmor frequencies, the high frequencies allow for higher time resolution for molecular dynamics as well as for transient paramagnetic intermediates studied with time-resolved EPR. Pulsed EPR methods are used for example for relaxation-time studies, and pulsed Electron Nuclear DOuble Resonance (ENDOR) is used to resolve unresolved hyperfine structure hidden in inhomogeneous linewidths. In the present article we introduce the basic concepts and selected applications to structure and mobility studies on electron transfer systems, reaction centers of photosynthesis as well as biomimetic models. The article concludes with an introduction to stochastic EPR which makes use of an other concept for investigating resonance systems in order to increase the excitation bandwidth of pulsed EPR. The limited excitation bandwidth of pulses at high frequency is one of the main limitations which, so far, made Fourier transform methods hardly feasible.

High-frequency high-voltage high-power DC-to-DC converters

NASA Astrophysics Data System (ADS)

Wilson, T. G.; Owen, H. A., Jr.; Wilson, P. M.

1981-07-01

The current and voltage waveshapes associated with the power transitor and the power diode in an example current-or-voltage step-up (buck-boost) converter were analyzed to highlight the problems and possible tradeoffs involved in the design of high voltage high power converters operating at switching frequencies in the range of 100 Khz. Although the fast switching speeds of currently available power diodes and transistors permit converter operation at high switching frequencies, the resulting time rates of changes of current coupled with parasitic inductances in series with the semiconductor switches, produce large repetitive voltage transients across the semiconductor switches, potentially far in excess of the device voltage ratings. The need is established for semiconductor switch protection circuitry to control the peak voltages appearing across the semiconductor switches, as well as to provide the waveshaping action require for a given semiconductor device. The possible tradeoffs, as well as the factors affecting the tradeoffs that must be considered in order to maximize the efficiency of the converters are enumerated.

High-frequency high-voltage high-power DC-to-DC converters

NASA Technical Reports Server (NTRS)

Wilson, T. G.; Owen, H. A., Jr.; Wilson, P. M.

1981-01-01

The current and voltage waveshapes associated with the power transitor and the power diode in an example current-or-voltage step-up (buck-boost) converter were analyzed to highlight the problems and possible tradeoffs involved in the design of high voltage high power converters operating at switching frequencies in the range of 100 Khz. Although the fast switching speeds of currently available power diodes and transistors permit converter operation at high switching frequencies, the resulting time rates of changes of current coupled with parasitic inductances in series with the semiconductor switches, produce large repetitive voltage transients across the semiconductor switches, potentially far in excess of the device voltage ratings. The need is established for semiconductor switch protection circuitry to control the peak voltages appearing across the semiconductor switches, as well as to provide the waveshaping action require for a given semiconductor device. The possible tradeoffs, as well as the factors affecting the tradeoffs that must be considered in order to maximize the efficiency of the converters are enumerated.

Ultra high vacuum broad band high power microwave window

DOEpatents

Nguyen-Tuong, V.; Dylla, H.F. III

1997-11-04

An improved high vacuum microwave window has been developed that utilizes high density polyethylene coated on two sides with SiOx, SiNx, or a combination of the two. The resultant low dielectric and low loss tangent window creates a low outgassing, low permeation seal through which broad band, high power microwave energy may be passed. No matching device is necessary and the sealing technique is simple. The features of the window are broad band transmission, ultra-high vacuum compatibility with a simple sealing technique, low voltage standing wave ratio, high power transmission and low cost. 5 figs.

Ultra high vacuum broad band high power microwave window

DOEpatents

Nguyen-Tuong, Viet; Dylla, III, Henry Frederick

1997-01-01

An improved high vacuum microwave window has been developed that utilizes high density polyethylene coated on two sides with SiOx, SiNx, or a combination of the two. The resultant low dielectric and low loss tangent window creates a low outgassing, low permeation seal through which broad band, high power microwave energy may be passed. No matching device is necessary and the sealing technique is simple. The features of the window are broad band transmission, ultra-high vacuum compatibility with a simple sealing technique, low voltage standing wave ratio, high power transmission and low cost.

High-frequency high-voltage high-power DC-to-DC converters

NASA Technical Reports Server (NTRS)

Wilson, T. G.; Owen, H. A.; Wilson, P. M.

1982-01-01

A simple analysis of the current and voltage waveshapes associated with the power transistor and the power diode in an example current-or-voltage step-up (buck-boost) converter is presented. The purpose of the analysis is to provide an overview of the problems and design trade-offs which must be addressed as high-power high-voltage converters are operated at switching frequencies in the range of 100 kHz and beyond. Although the analysis focuses on the current-or-voltage step-up converter as the vehicle for discussion, the basic principles presented are applicable to other converter topologies as well.

High-frequency high-voltage high-power DC-to-DC converters

NASA Astrophysics Data System (ADS)

Wilson, T. G.; Owen, H. A.; Wilson, P. M.

1982-09-01

A simple analysis of the current and voltage waveshapes associated with the power transistor and the power diode in an example current-or-voltage step-up (buck-boost) converter is presented. The purpose of the analysis is to provide an overview of the problems and design trade-offs which must be addressed as high-power high-voltage converters are operated at switching frequencies in the range of 100 kHz and beyond. Although the analysis focuses on the current-or-voltage step-up converter as the vehicle for discussion, the basic principles presented are applicable to other converter topologies as well.

A Double-Pole High Voltage High Current Switch

DTIC Science & Technology

2005-12-01

NAVAL POSTGRADUATE SCHOOL MONTEREY, CALIFORNIA THESIS Approved for public release; distribution is unlimited A DOUBLE- POLE HIGH...December 2005 3. REPORT TYPE AND DATES COVERED Master’s Thesis 4. TITLE AND SUBTITLE: A Double- Pole High Voltage High Current Switch 6. AUTHOR(S...to divert heavy charged particles, e.g. Cu+. 15. NUMBER OF PAGES 68 14. SUBJECT TERMS Double- Pole , Pulse Forming Inductive Network, PFIN

High-Speed, high-power, switching transistor

NASA Technical Reports Server (NTRS)

Carnahan, D.; Ohu, C. K.; Hower, P. L.

1979-01-01

Silicon transistor rate for 200 angstroms at 400 to 600 volts combines switching speed of transistors with ruggedness, power capacity of thyristor. Transistor introduces unique combination of increased power-handling capability, unusally low saturation and switching losses, and submicrosecond switching speeds. Potential applications include high power switching regulators, linear amplifiers, chopper controls for high frequency electrical vehicle drives, VLF transmitters, RF induction heaters, kitchen cooking ranges, and electronic scalpels for medical surgery.

New concept high-speed and high-resolution color scanner

NASA Astrophysics Data System (ADS)

Nakashima, Keisuke; Shinoda, Shin'ichi; Konishi, Yoshiharu; Sugiyama, Kenji; Hori, Tetsuya

2003-05-01

We have developed a new concept high-speed and high-resolution color scanner (Blinkscan) using digital camera technology. With our most advanced sub-pixel image processing technology, approximately 12 million pixel image data can be captured. High resolution imaging capability allows various uses such as OCR, color document read, and document camera. The scan time is only about 3 seconds for a letter size sheet. Blinkscan scans documents placed "face up" on its scan stage and without any special illumination lights. Using Blinkscan, a high-resolution color document can be easily inputted into a PC at high speed, a paperless system can be built easily. It is small, and since the occupancy area is also small, setting it on an individual desk is possible. Blinkscan offers the usability of a digital camera and accuracy of a flatbed scanner with high-speed processing. Now, about several hundred of Blinkscan are mainly shipping for the receptionist operation in a bank and a security. We will show the high-speed and high-resolution architecture of Blinkscan. Comparing operation-time with conventional image capture device, the advantage of Blinkscan will make clear. And image evaluation for variety of environment, such as geometric distortions or non-uniformity of brightness, will be made.

High resolution gamma-ray spectroscopy at high count rates with a prototype High Purity Germanium detector

NASA Astrophysics Data System (ADS)

Cooper, R. J.; Amman, M.; Vetter, K.

2018-04-01

High-resolution gamma-ray spectrometers are required for applications in nuclear safeguards, emergency response, and fundamental nuclear physics. To overcome one of the shortcomings of conventional High Purity Germanium (HPGe) detectors, we have developed a prototype device capable of achieving high event throughput and high energy resolution at very high count rates. This device, the design of which we have previously reported on, features a planar HPGe crystal with a reduced-capacitance strip electrode geometry. This design is intended to provide good energy resolution at the short shaping or digital filter times that are required for high rate operation and which are enabled by the fast charge collection afforded by the planar geometry crystal. In this work, we report on the initial performance of the system at count rates up to and including two million counts per second.

High Cycle-life Shape Memory Polymer at High Temperature

PubMed Central

Kong, Deyan; Xiao, Xinli

2016-01-01

High cycle-life is important for shape memory materials exposed to numerous cycles, and here we report shape memory polyimide that maintained both high shape fixity (Rf) and shape recovery (Rr) during the more than 1000 bending cycles tested. Its critical stress is 2.78 MPa at 250 °C, and the shape recovery process can produce stored energy of 0.218 J g−1 at the efficiency of 31.3%. Its high Rf is determined by the large difference in storage modulus at rubbery and glassy states, while the high Rr mainly originates from its permanent phase composed of strong π-π interactions and massive chain entanglements. Both difference in storage modulus and overall permanent phase were preserved during the bending deformation cycles, and thus high Rf and Rr were observed in every cycle and the high cycle-life will expand application areas of SMPs enormously. PMID:27641148

Progress of OLED devices with high efficiency at high luminance

NASA Astrophysics Data System (ADS)

Nguyen, Carmen; Ingram, Grayson; Lu, Zhenghong

2014-03-01

Organic light emitting diodes (OLEDs) have progressed significantly over the last two decades. For years, OLEDs have been promoted as the next generation technology for flat panel displays and solid-state lighting due to their potential for high energy efficiency and dynamic range of colors. Although high efficiency can readily be obtained at low brightness levels, a significant decline at high brightness is commonly observed. In this report, we will review various strategies for achieving highly efficient phosphorescent OLED devices at high luminance. Specifically, we will provide details regarding the performance and general working principles behind each strategy. We will conclude by looking at how some of these strategies can be combined to produce high efficiency white OLEDs at high brightness.

Pressure-resisting cell for high-pressure, high-resolution nuclear magnetic resonance measurements at very high magnetic fields

NASA Astrophysics Data System (ADS)

Yamada, H.; Nishikawa, K.; Honda, M.; Shimura, T.; Akasaka, K.; Tabayashi, K.

2001-02-01

A pressure-resisting cell system has been developed for high-pressure high-resolution nuclear magnetic resonance (NMR) measurements up to a maximum pressure of 600 MPa. This cell system is capable of performing high-pressure experiments with any standard spectrometer, including modern high field NMR machines. A full description of the high-pressure NMR assembly mounted on a 750 MHz spectrometer is presented along with a detailed explanation of the procedure for preparing the pressure-resisting quartz and glass cells.

High-Flow, High-Molecular-Weight, Addition-Curing Polyimides

NASA Technical Reports Server (NTRS)

Chuang, Kathy C.; Vannucci, Raymond D.

1993-01-01

In developed series of high-flow PMR-type polyimide resins, 2, 2'-bis(trifluoromethyl)-4, 4'-diaminobiphenyl (BTDB) substituted for 1, 4-pheylenediamine in PMR-II formulation. Polyimides designated either as PMR-12F when nadic ester (NE) end caps used, or as V-CAP-12F when p-aminostyrene end caps used. High-molecular-weight, addition-curing polyimides based on BTBD and HFDE highly processable high-temperature matrix resins used to make composite materials with excellent retention of properties during long-term exposure to air at 650 degrees F or higher temperature. Furthermore, 12F addition-curing polyimides useful for electronic applications; fluorinated rigid-rod polyimides known to exhibit low thermal expansion coefficients as well as low absorption of moisture.

High Points.

ERIC Educational Resources Information Center

Potell, Herbert, Ed.

1977-01-01

This is a compilation of written contributions submitted by professional and nonprofessional employees of New York City high schools. Contained in this issue are a series of articles on high school self renewal, and other articles on: the partnership between Andrew Jackson High School and Queens College; foreign language study and moral values in…

High to ultra-high power electrical energy storage.

PubMed

Sherrill, Stefanie A; Banerjee, Parag; Rubloff, Gary W; Lee, Sang Bok

2011-12-14

High power electrical energy storage systems are becoming critical devices for advanced energy storage technology. This is true in part due to their high rate capabilities and moderate energy densities which allow them to capture power efficiently from evanescent, renewable energy sources. High power systems include both electrochemical capacitors and electrostatic capacitors. These devices have fast charging and discharging rates, supplying energy within seconds or less. Recent research has focused on increasing power and energy density of the devices using advanced materials and novel architectural design. An increase in understanding of structure-property relationships in nanomaterials and interfaces and the ability to control nanostructures precisely has led to an immense improvement in the performance characteristics of these devices. In this review, we discuss the recent advances for both electrochemical and electrostatic capacitors as high power electrical energy storage systems, and propose directions and challenges for the future. We asses the opportunities in nanostructure-based high power electrical energy storage devices and include electrochemical and electrostatic capacitors for their potential to open the door to a new regime of power energy.

High assurance SPIRAL

NASA Astrophysics Data System (ADS)

Franchetti, Franz; Sandryhaila, Aliaksei; Johnson, Jeremy R.

2014-06-01

In this paper we introduce High Assurance SPIRAL to solve the last mile problem for the synthesis of high assurance implementations of controllers for vehicular systems that are executed in today's and future embedded and high performance embedded system processors. High Assurance SPIRAL is a scalable methodology to translate a high level specification of a high assurance controller into a highly resource-efficient, platform-adapted, verified control software implementation for a given platform in a language like C or C++. High Assurance SPIRAL proves that the implementation is equivalent to the specification written in the control engineer's domain language. Our approach scales to problems involving floating-point calculations and provides highly optimized synthesized code. It is possible to estimate the available headroom to enable assurance/performance trade-offs under real-time constraints, and enables the synthesis of multiple implementation variants to make attacks harder. At the core of High Assurance SPIRAL is the Hybrid Control Operator Language (HCOL) that leverages advanced mathematical constructs expressing the controller specification to provide high quality translation capabilities. Combined with a verified/certified compiler, High Assurance SPIRAL provides a comprehensive complete solution to the efficient synthesis of verifiable high assurance controllers. We demonstrate High Assurance SPIRALs capability by co-synthesizing proofs and implementations for attack detection and sensor spoofing algorithms and deploy the code as ROS nodes on the Landshark unmanned ground vehicle and on a Synthetic Car in a real-time simulator.

High-Gain High-Field Fusion Plasma

PubMed Central

Li, Ge

2015-01-01

A Faraday wheel (FW)—an electric generator of constant electrical polarity that produces huge currents—could be implemented in an existing tokamak to study high-gain high-field (HGHF) fusion plasma, such as the Experimental Advanced Superconducting Tokamak (EAST). HGHF plasma can be realized in EAST by updating its pulsed-power system to compress plasma in two steps by induction fields; high gains of the Lawson trinity parameter and fusion power are both predicted by formulating the HGHF plasma. Both gain rates are faster than the decrease rate of the plasma volume. The formulation is checked by earlier ATC tests. Good agreement between theory and tests indicates that scaling to over 10 T at EAST may be possible by two-step compressions with a compression ratio of the minor radius of up to 3. These results point to a quick new path of fusion plasma study, i.e., simulating the Sun by EAST. PMID:26507314

Localizing high-lying Rydberg wave packets with two-color laser fields

NASA Astrophysics Data System (ADS)

Larimian, Seyedreza; Lemell, Christoph; Stummer, Vinzenz; Geng, Ji-Wei; Roither, Stefan; Kartashov, Daniil; Zhang, Li; Wang, Mu-Xue; Gong, Qihuang; Peng, Liang-You; Yoshida, Shuhei; Burgdörfer, Joachim; Baltuška, Andrius; Kitzler, Markus; Xie, Xinhua

2017-08-01

We demonstrate control over the localization of high-lying Rydberg wave packets in argon atoms with phase-locked orthogonally polarized two-color laser fields. With a reaction microscope, we measure ionization signals of high-lying Rydberg states induced by a weak dc field and blackbody radiation as a function of the relative phase between the two-color fields. We find that the dc-field-ionization yield of high-lying Rydberg argon atoms oscillates with the relative two-color phase with a period of 2 π while the photoionization signal by blackbody radiation shows a period of π . Accompanying simulations show that these observations are a clear signature of the asymmetric localization of electrons recaptured into very elongated (low angular momentum) high-lying Rydberg states after conclusion of the laser pulse. Our findings thus open an effective pathway to control the localization of high-lying Rydberg wave packets.

High School/College Collaboration that Promotes High School Success.

ERIC Educational Resources Information Center

Conklin, David

Over the past few years, Mercer County Community College (MCCC) in Trenton, New Jersey, has developed several programs and activities to promote a closer relationship between the college and local junior high and high schools. The programs are built on the premise that well-prepared students are more likely to persist through high school and…

Large aspheric optics for high-power, high-energy laser

NASA Astrophysics Data System (ADS)

Geyl, Roland; Houbre, Francois

2001-12-01

SAGEM, within its REOSC high performance optics product line, has developed through the years a specific knowledge in large plano, spherical and aspherical optics for high energy or high power laser. This paper is aimed to illustrate the application of aspheric optics for such laser application with several examples of increasing optical surface complexity.

Dynamic High-temperature Testing of an Iridium Alloy in Compression at High-strain Rates: Dynamic High-temperature Testing

DOE PAGES

Song, B.; Nelson, K.; Lipinski, R.; ...

2014-08-21

Iridium alloys have superior strength and ductility at elevated temperatures, making them useful as structural materials for certain high-temperature applications. However, experimental data on their high-strain -rate performance are needed for understanding high-speed impacts in severe environments. Kolsky bars (also called split Hopkinson bars) have been extensively employed for high-strain -rate characterization of materials at room temperature, but it has been challenging to adapt them for the measurement of dynamic properties at high temperatures. In our study, we analyzed the difficulties encountered in high-temperature Kolsky bar testing of thin iridium alloy specimens in compression. We made appropriate modifications using themore » current high-temperature Kolsky bar technique in order to obtain reliable compressive stress–strain response of an iridium alloy at high-strain rates (300–10 000 s -1) and temperatures (750 and 1030°C). The compressive stress–strain response of the iridium alloy showed significant sensitivity to both strain rate and temperature.« less

Review on fatigue behavior of high-strength concrete after high temperature

NASA Astrophysics Data System (ADS)

Zhao, Dongfu; Jia, Penghe; Gao, Haijing

2017-06-01

The fatigue of high-strength concrete after high temperature has begun to attract attention. But so far the researches work about the fatigue of high-strength concrete after high temperature have not been reported. This article based on a large number of literature. The research work about the fatigue of high-strength concrete after high temperature are reviewed, analysed and expected, which can provide some reference for the experimental study of fatigue damage analysis.

High speed, high current pulsed driver circuit

DOEpatents

Carlen, Christopher R.

2017-03-21

Various technologies presented herein relate to driving a LED such that the LED emits short duration pulses of light. This is accomplished by driving the LED with short duration, high amplitude current pulses. When the LED is driven by short duration, high amplitude current pulses, the LED emits light at a greater amplitude compared to when the LED is driven by continuous wave current.

Flying-plate detonator using a high-density high explosive

DOEpatents

Stroud, John R.; Ornellas, Donald L.

1988-01-01

A flying-plate detonator containing a high-density high explosive such as benzotrifuroxan (BTF). The detonator involves the electrical explosion of a thin metal foil which punches out a flyer from a layer overlying the foil, and the flyer striking a high-density explosive pellet of BTF, which is more thermally stable than the conventional detonator using pentaerythritol tetranitrate (PETN).

High frequency, high power capacitor development

NASA Astrophysics Data System (ADS)

White, C. W.; Hoffman, P. S.

1983-03-01

A program to develop a special high energy density, high power transfer capacitor to operate at frequency of 40 kHz, 600 V rms at 125 A rms plus 600 V dc bias for space operation. The program included material evaluation and selection, a capacitor design was prepared, a thermal analysis performed on the design. Fifty capacitors were manufactured for testing at 10 kHz and 40 kHz for 50 hours at Industrial Electric Heating Co. of Columbus, Ohio. The vacuum endurance test used on environmental chamber and temperature plate furnished by Maxwell. The capacitors were energized with a special power conditioning apparatus developed by Industrial Electric Heating Co. Temperature conditions of the capacitors were monitored by IEHCo test equipment. Successful completion of the vacuum endurance test series confirmed achievement of the main goal of producing a capacitor or reliable operation at high frequency in an environment normally not hospitable to electrical and electronic components. The capacitor developed compared to a typical commercial capacitor at the 40 kHz level represents a decrease in size and weight by a factor of seven.

High frequency, high power capacitor development

NASA Technical Reports Server (NTRS)

White, C. W.; Hoffman, P. S.

1983-01-01

A program to develop a special high energy density, high power transfer capacitor to operate at frequency of 40 kHz, 600 V rms at 125 A rms plus 600 V dc bias for space operation. The program included material evaluation and selection, a capacitor design was prepared, a thermal analysis performed on the design. Fifty capacitors were manufactured for testing at 10 kHz and 40 kHz for 50 hours at Industrial Electric Heating Co. of Columbus, Ohio. The vacuum endurance test used on environmental chamber and temperature plate furnished by Maxwell. The capacitors were energized with a special power conditioning apparatus developed by Industrial Electric Heating Co. Temperature conditions of the capacitors were monitored by IEHCo test equipment. Successful completion of the vacuum endurance test series confirmed achievement of the main goal of producing a capacitor or reliable operation at high frequency in an environment normally not hospitable to electrical and electronic components. The capacitor developed compared to a typical commercial capacitor at the 40 kHz level represents a decrease in size and weight by a factor of seven.

High output lamp with high brightness

DOEpatents

Kirkpatrick, Douglas A.; Bass, Gary K.; Copsey, Jesse F.; Garber, Jr., William E.; Kwong, Vincent H.; Levin, Izrail; MacLennan, Donald A.; Roy, Robert J.; Steiner, Paul E.; Tsai, Peter; Turner, Brian P.

2002-01-01

An ultra bright, low wattage inductively coupled electrodeless aperture lamp is powered by a solid state RF source in the range of several tens to several hundreds of watts at various frequencies in the range of 400 to 900 MHz. Numerous novel lamp circuits and components are disclosed including a wedding ring shaped coil having one axial and one radial lead, a high accuracy capacitor stack, a high thermal conductivity aperture cup and various other aperture bulb configurations, a coaxial capacitor arrangement, and an integrated coil and capacitor assembly. Numerous novel RF circuits are also disclosed including a high power oscillator circuit with reduced complexity resonant pole configuration, parallel RF power FET transistors with soft gate switching, a continuously variable frequency tuning circuit, a six port directional coupler, an impedance switching RF source, and an RF source with controlled frequency-load characteristics. Numerous novel RF control methods are disclosed including controlled adjustment of the operating frequency to find a resonant frequency and reduce reflected RF power, controlled switching of an impedance switched lamp system, active power control and active gate bias control.

High-Power, High-Speed Electro-Optic Pockels Cell Modulator

NASA Technical Reports Server (NTRS)

Hawthorne, Justin; Battle, Philip

2013-01-01

Electro-optic modulators rely on a change in the index of refraction for the optical wave as a function of an applied voltage. The corresponding change in index acts to delay the wavefront in the waveguide. The goal of this work was to develop a high-speed, high-power waveguide- based modulator (phase and amplitude) and investigate its use as a pulse slicer. The key innovation in this effort is the use of potassium titanyl phosphate (KTP) waveguides, making the highpower, polarization-based waveguide amplitude modulator possible. Furthermore, because it is fabricated in KTP, the waveguide component will withstand high optical power and have a significantly higher RF modulation figure of merit (FOM) relative to lithium niobate. KTP waveguides support high-power TE and TM modes - a necessary requirement for polarization-based modulation as with a Pockels cell. High-power fiber laser development has greatly outpaced fiber-based modulators in terms of its maturity and specifications. The demand for high-performance nonlinear optical (NLO) devices in terms of power handling, efficiency, bandwidth, and useful wavelength range has driven the development of bulk NLO options, which are limited in their bandwidth, as well as waveguide based LN modulators, which are limited by their low optical damage threshold. Today, commercially available lithium niobate (LN) modulators are used for laser formatting; however, because of photorefractive damage that can reduce transmission and increase requirements on bias control, LN modulators cannot be used with powers over several mW, dependent on wavelength. The high-power, high-speed modulators proposed for development under this effort will enable advancements in several exciting fields including lidarbased remote sensing, atomic interferometry, free-space laser communications, and others.

2. GORGE HIGH DAM. UNUSUALLY HIGH WATER IN GORGE LAKE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. GORGE HIGH DAM. UNUSUALLY HIGH WATER IN GORGE LAKE DUE TO THE COMBINATION OF UNIT 24 BEING DOWN FOR REWINDING AND TWO UNITS COMING ON LINE UNEXPECTEDLY AT ROSS POWERHOUSE LED TO WATER FLOWING OVER THE SPILLGATES. EACH GATE IF 47 FEET WIDE AND 50 FEET HIGH, 1989. - Skagit Power Development, Gorge High Dam, On Skagit River, 2.9 miles upstream from Newhalem, Newhalem, Whatcom County, WA

High-capacity high-speed recording

NASA Astrophysics Data System (ADS)

Jamberdino, A. A.

1981-06-01

Continuing advances in wideband communications and information handling are leading to extremely large volume digital data systems for which conventional data storage techniques are becoming inadequate. The paper presents an assessment of alternative recording technologies for the extremely wideband, high capacity storage and retrieval systems currently under development. Attention is given to longitudinal and rotary head high density magnetic recording, laser holography in human readable/machine readable devices and a wideband recorder, digital optical disks, and spot recording in microfiche formats. The electro-optical technologies considered are noted to be capable of providing data bandwidths up to 1000 megabits/sec and total data storage capacities in the 10 to the 11th to 10 to the 12th bit range, an order of magnitude improvement over conventional technologies.

High strength, high ductility low carbon steel

DOEpatents

Koo, Jayoung; Thomas, Gareth

1978-01-01

A high strength, high ductility low carbon steel consisting essentially of iron, 0.05-0.15 wt% carbon, and 1-3 wt% silicon. Minor amounts of other constituents may be present. The steel is characterized by a duplex ferrite-martensite microstructure in a fibrous morphology. The microstructure is developed by heat treatment consisting of initial austenitizing treatment followed by annealing in the (.alpha. + .gamma.) range with intermediate quenching.

Application of polarization in high speed, high contrast inspection

NASA Astrophysics Data System (ADS)

Novak, Matthew J.

2017-08-01

Industrial optical inspection often requires high speed and high throughput of materials. Engineers use a variety of techniques to handle these inspection needs. Some examples include line scan cameras, high speed multi-spectral and laser-based systems. High-volume manufacturing presents different challenges for inspection engineers. For example, manufacturers produce some components in quantities of millions per month, per week or even per day. Quality control of so many parts requires creativity to achieve the measurement needs. At times, traditional vision systems lack the contrast to provide the data required. In this paper, we show how dynamic polarization imaging captures high contrast images. These images are useful for engineers to perform inspection tasks in some cases where optical contrast is low. We will cover basic theory of polarization. We show how to exploit polarization as a contrast enhancement technique. We also show results of modeling for a polarization inspection application. Specifically, we explore polarization techniques for inspection of adhesives on glass.

Three-Dimensional Printable High-Temperature and High-Rate Heaters.

PubMed

Yao, Yonggang; Fu, Kun Kelvin; Yan, Chaoyi; Dai, Jiaqi; Chen, Yanan; Wang, Yibo; Zhang, Bilun; Hitz, Emily; Hu, Liangbing

2016-05-24

High temperature heaters are ubiquitously used in materials synthesis and device processing. In this work, we developed three-dimensional (3D) printed reduced graphene oxide (RGO)-based heaters to function as high-performance thermal supply with high temperature and ultrafast heating rate. Compared with other heating sources, such as furnace, laser, and infrared radiation, the 3D printed heaters demonstrated in this work have the following distinct advantages: (1) the RGO based heater can operate at high temperature up to 3000 K because of using the high temperature-sustainable carbon material; (2) the heater temperature can be ramped up and down with extremely fast rates, up to ∼20 000 K/second; (3) heaters with different shapes can be directly printed with small sizes and onto different substrates to enable heating anywhere. The 3D printable RGO heaters can be applied to a wide range of nanomanufacturing when precise temperature control in time, placement, and the ramping rate are important.

High resolution, high rate x-ray spectrometer

DOEpatents

Goulding, F.S.; Landis, D.A.

1983-07-14

It is an object of the invention to provide a pulse processing system for use with detected signals of a wide dynamic range which is capable of very high counting rates, with high throughput, with excellent energy resolution and a high signal-to-noise ratio. It is a further object to provide a pulse processing system wherein the fast channel resolving time is quite short and substantially independent of the energy of the detected signals. Another object is to provide a pulse processing system having a pile-up rejector circuit which will allow the maximum number of non-interfering pulses to be passed to the output. It is also an object of the invention to provide new methods for generating substantially symmetrically triangular pulses for use in both the main and fast channels of a pulse processing system.

High mobility and high stability glassy metal-oxynitride materials and devices

NASA Astrophysics Data System (ADS)

Lee, Eunha; Kim, Taeho; Benayad, Anass; Hur, Jihyun; Park, Gyeong-Su; Jeon, Sanghun

2016-04-01

In thin film technology, future semiconductor and display products with high performance, high density, large area, and ultra high definition with three-dimensional functionalities require high performance thin film transistors (TFTs) with high stability. Zinc oxynitride, a composite of zinc oxide and zinc nitride, has been conceded as a strong substitute to conventional semiconductor film such as silicon and indium gallium zinc oxide due to high mobility value. However, zinc oxynitride has been suffered from poor reproducibility due to relatively low binding energy of nitrogen with zinc, resulting in the instability of composition and its device performance. Here we performed post argon plasma process on zinc oxynitride film, forming nano-crystalline structure in stable amorphous matrix which hampers the reaction of oxygen with zinc. Therefore, material properties and device performance of zinc oxynitride are greatly enhanced, exhibiting robust compositional stability even exposure to air, uniform phase, high electron mobility, negligible fast transient charging and low noise characteristics. Furthermore, We expect high mobility and high stability zinc oxynitride customized by plasma process to be applicable to a broad range of semiconductor and display devices.

High-cost, high-capacity backbone for global brain communication.

PubMed

van den Heuvel, Martijn P; Kahn, René S; Goñi, Joaquín; Sporns, Olaf

2012-07-10

Network studies of human brain structural connectivity have identified a specific set of brain regions that are both highly connected and highly central. Recent analyses have shown that these putative hub regions are mutually and densely interconnected, forming a "rich club" within the human brain. Here we show that the set of pathways linking rich club regions forms a central high-cost, high-capacity backbone for global brain communication. Diffusion tensor imaging (DTI) data of two sets of 40 healthy subjects were used to map structural brain networks. The contributions to network cost and communication capacity of global cortico-cortical connections were assessed through measures of their topology and spatial embedding. Rich club connections were found to be more costly than predicted by their density alone and accounted for 40% of the total communication cost. Furthermore, 69% of all minimally short paths between node pairs were found to travel through the rich club and a large proportion of these communication paths consisted of ordered sequences of edges ("path motifs") that first fed into, then traversed, and finally exited the rich club, while passing through nodes of increasing and then decreasing degree. The prevalence of short paths that follow such ordered degree sequences suggests that neural communication might take advantage of strategies for dynamic routing of information between brain regions, with an important role for a highly central rich club. Taken together, our results show that rich club connections make an important contribution to interregional signal traffic, forming a central high-cost, high-capacity backbone for global brain communication.

Proton shock acceleration using a high contrast high intensity laser

NASA Astrophysics Data System (ADS)

Gauthier, Maxence; Roedel, Christian; Kim, Jongjin; Aurand, Bastian; Curry, Chandra; Goede, Sebastian; Propp, Adrienne; Goyon, Clement; Pak, Art; Kerr, Shaun; Ramakrishna, Bhuvanesh; Ruby, John; William, Jackson; Glenzer, Siegfried

2015-11-01

Laser-driven proton acceleration is a field of intense research due to the interesting characteristics of this novel particle source including high brightness, high maximum energy, high laminarity, and short duration. Although the ion beam characteristics are promising for many future applications, such as in the medical field or hybrid accelerators, the ion beam generated using TNSA, the acceleration mechanism commonly achieved, still need to be significantly improved. Several new alternative mechanisms have been proposed such as collisionless shock acceleration (CSA) in order to produce a mono-energetic ion beam favorable for those applications. We report the first results of an experiment performed with the TITAN laser system (JLF, LLNL) dedicated to the study of CSA using a high intensity (5x1019W/cm2) high contrast ps laser pulse focused on 55 μm thick CH and CD targets. We show that the proton spectrum generated during the interaction exhibits high-energy mono-energetic features along the laser axis, characteristic of a shock mechanism.

Ultra-high polarity ceramics induced extrinsic high permittivity of polymers contributing to high permittivity of 2-2 series composites

NASA Astrophysics Data System (ADS)

Feng, Yefeng; Zhang, Jianxiong; Hu, Jianbing; Peng, Cheng; He, Renqi

2018-01-01

Induced polarization at interface has been confirmed to have significant impact on the dielectric properties of 2-2 series composites bearing Si-based semi-conductor sheet and polymer layer. By compositing, the significantly elevated high permittivity in Si-based semi-conductor sheet should be responsible for the obtained high permittivity in composites. In that case, interface interaction could include two aspects namely a strong electrostatic force from high polarity polymeric layer and a newborn high polarity induced in Si-based ceramic sheet. In this work, this class of interface induced polarization was successfully extended into another 2-2 series composite system made up of ultra-high polarity ceramic sheet and high polarity polymer layer. By compositing, the greatly improved high permittivity in high polarity polymer layer was confirmed to strongly contribute to the high permittivity achieved in composites. In this case, interface interaction should consist of a rather large electrostatic force from ultra-high polarity ceramic sheet with ionic crystal structure and an enhanced high polarity induced in polymer layer based on a large polarizability of high polarity covalent dipoles in polymer. The dielectric and conductive properties of four designed 2-2 series composites and their components have been detailedly investigated. Increasing of polymer inborn polarity would lead to a significant elevating of polymer overall polarity in composite. Decline of inherent polarities in two components would result in a mild improving of polymer total polarity in composite. Introducing of non-polarity polymeric layer would give rise to a hardly unaltered polymer overall polarity in composite. The best 2-2 composite could possess a permittivity of ˜463 at 100 Hz 25.7 times of the original permittivity of polymer in it. This work might offer a facile route for achieving the promising composite dielectrics by constructing the 2-2 series samples from two high polarity

High-frequency applications of high-temperature superconductor thin films

NASA Astrophysics Data System (ADS)

Klein, N.

2002-10-01

High-temperature superconducting thin films offer unique properties which can be utilized for a variety of high-frequency device applications in many areas related to the strongly progressing market of information technology. One important property is an exceptionally low level of microwave absorption at temperatures attainable with low power cryocoolers. This unique property has initiated the development of various novel type of microwave devices and commercialized subsystems with special emphasis on application in advanced microwave communication systems. The second important achievement related to efforts in oxide thin and multilayer technology was the reproducible fabrication of low-noise Josephson junctions in high-temperature superconducting thin films. As a consequence of this achievement, several novel nonlinear high-frequency devices, most of them exploiting the unique features of the ac Josephson effect, have been developed and found to exhibit challenging properties to be utilized in basic metrology and Terahertz technology. On the longer timescale, the achievements in integrated high-temperature superconductor circuit technology may offer a strong potential for the development of digital devices with possible clock frequencies in the range of 100 GHz.

High-temperature testing of high performance fiber reinforced concrete

NASA Astrophysics Data System (ADS)

Fořt, Jan; Vejmelková, Eva; Pavlíková, Milena; Trník, Anton; Čítek, David; Kolísko, Jiří; Černý, Robert; Pavlík, Zbyšek

2016-06-01

The effect of high-temperature exposure on properties of High Performance Fiber Reinforced Concrete (HPFRC) is researched in the paper. At first, reference measurements are done on HPFRC samples without high-temperature loading. Then, the HPFRC samples are exposed to the temperatures of 200, 400, 600, 800, and 1000 °C. For the temperature loaded samples, measurement of residual mechanical and basic physical properties is done. Linear thermal expansion coefficient as function of temperature is accessed on the basis of measured thermal strain data. Additionally, simultaneous difference scanning calorimetry (DSC) and thermogravimetry (TG) analysis is performed in order to observe and explain material changes at elevated temperature. It is found that the applied high temperature loading significantly increases material porosity due to the physical, chemical and combined damage of material inner structure, and negatively affects also the mechanical strength. Linear thermal expansion coefficient exhibits significant dependence on temperature and changes of material structure. The obtained data will find use as input material parameters for modelling the damage of HPFRC structures exposed to the fire and high temperature action.

High Power High Efficiency Diode Laser Stack for Processing

NASA Astrophysics Data System (ADS)

Gu, Yuanyuan; Lu, Hui; Fu, Yueming; Cui, Yan

2018-03-01

High-power diode lasers based on GaAs semiconductor bars are well established as reliable and highly efficient laser sources. As diode laser is simple in structure, small size, longer life expectancy with the advantages of low prices, it is widely used in the industry processing, such as heat treating, welding, hardening, cladding and so on. Respectively, diode laser could make it possible to establish the practical application because of rectangular beam patterns which are suitable to make fine bead with less power. At this power level, it can have many important applications, such as surgery, welding of polymers, soldering, coatings and surface treatment of metals. But there are some applications, which require much higher power and brightness, e.g. hardening, key hole welding, cutting and metal welding. In addition, High power diode lasers in the military field also have important applications. So all developed countries have attached great importance to high-power diode laser system and its applications. This is mainly due their low performance. In this paper we will introduce the structure and the principle of the high power diode stack.

High-power laser diodes with high polarization purity

NASA Astrophysics Data System (ADS)

Rosenkrantz, Etai; Yanson, Dan; Peleg, Ophir; Blonder, Moshe; Rappaport, Noam; Klumel, Genady

2017-02-01

Fiber-coupled laser diode modules employ power scaling of single emitters for fiber laser pumping. To this end, techniques such as geometrical, spectral and polarization beam combining (PBC) are used. For PBC, linear polarization with high degree of purity is important, as any non-perfectly polarized light leads to losses and heating. Furthermore, PBC is typically performed in a collimated portion of the beams, which also cancels the angular dependence of the PBC element, e.g., beam-splitter. However, we discovered that single emitters have variable degrees of polarization, which depends both on the operating current and far-field divergence. We present data to show angle-resolved polarization measurements that correlate with the ignition of high-order modes in the slow-axis emission of the emitter. We demonstrate that the ultimate laser brightness includes not only the standard parameters such as power, emitting area and beam divergence, but also the degree of polarization (DoP), which is a strong function of the latter. Improved slow-axis divergence, therefore, contributes not only to high brightness but also high beam combining efficiency through polarization.

High-resolution wavefront control of high-power laser systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brase, J; Brown, C; Carrano, C

1999-07-08

Nearly every new large-scale laser system application at LLNL has requirements for beam control which exceed the current level of available technology. For applications such as inertial confinement fusion, laser isotope separation, laser machining, and laser the ability to transport significant power to a target while maintaining good beam quality is critical. There are many ways that laser wavefront quality can be degraded. Thermal effects due to the interaction of high-power laser or pump light with the internal optical components or with the ambient gas are common causes of wavefront degradation. For many years, adaptive optics based on thing deformablemore » glass mirrors with piezoelectric or electrostrictive actuators have be used to remove the low-order wavefront errors from high-power laser systems. These adaptive optics systems have successfully improved laser beam quality, but have also generally revealed additional high-spatial-frequency errors, both because the low-order errors have been reduced and because deformable mirrors have often introduced some high-spatial-frequency components due to manufacturing errors. Many current and emerging laser applications fall into the high-resolution category where there is an increased need for the correction of high spatial frequency aberrations which requires correctors with thousands of degrees of freedom. The largest Deformable Mirrors currently available have less than one thousand degrees of freedom at a cost of approximately $1M. A deformable mirror capable of meeting these high spatial resolution requirements would be cost prohibitive. Therefore a new approach using a different wavefront control technology is needed. One new wavefront control approach is the use of liquid-crystal (LC) spatial light modulator (SLM) technology for the controlling the phase of linearly polarized light. Current LC SLM technology provides high-spatial-resolution wavefront control, with hundreds of thousands of degrees of

Highly Efficient Nondoped Green Organic Light-Emitting Diodes with Combination of High Photoluminescence and High Exciton Utilization.

PubMed

Wang, Chu; Li, Xianglong; Pan, Yuyu; Zhang, Shitong; Yao, Liang; Bai, Qing; Li, Weijun; Lu, Ping; Yang, Bing; Su, Shijian; Ma, Yuguang

2016-02-10

Photoluminescence (PL) efficiency and exciton utilization efficiency are two key parameters to harvest high-efficiency electroluminescence (EL) in organic light-emitting diodes (OLEDs). But it is not easy to simultaneously combine these two characteristics (high PL efficiency and high exciton utilization) into a fluorescent material. In this work, an efficient combination was achieved through two concepts of hybridized local and charge-transfer (CT) state (HLCT) and "hot exciton", in which the former is responsible for high PL efficiency while the latter contributes to high exciton utilization. On the basis of a tiny chemical modification in TPA-BZP, a green-light donor-acceptor molecule, we designed and synthesized CzP-BZP with this efficeient combination of high PL efficiency of η(PL) = 75% in the solid state and maximal exciton utilization efficiency up to 48% (especially, the internal quantum efficiency of η(IQE) = 35% substantially exceed 25% of spin statistics limit) in OLED. The nondoped OLED of CzP-BZP exhibited an excellent performance: a green emission with a CIE coordinate of (0.34, 0.60), a maximum current efficiency of 23.99 cd A(-1), and a maximum external quantum efficiency (EQE, η(EQE)) of 6.95%. This combined HLCT state and "hot exciton" strategy should be a practical way to design next-generation, low-cost, high-efficiency fluorescent OLED materials.

High voltage-high power components for large space power distribution systems

NASA Technical Reports Server (NTRS)

Renz, D. D.

1984-01-01

Space power components including a family of bipolar power switching transistors, fast switching power diodes, heat pipe cooled high frequency transformers and inductors, high frequency conduction cooled transformers, high power-high frequency capacitors, remote power controllers and rotary power transfer devices were developed. Many of these components such as the power switching transistors, power diodes and the high frequency capacitor are commercially available. All the other components were developed to the prototype level. The dc/dc series resonant converters were built to the 25 kW level.

Cenozoic to Cretaceous paleomagnetic dataset from Egypt: New data, review and global analysis

NASA Astrophysics Data System (ADS)

Perrin, Mireille; Saleh, Ahmed

2018-04-01

Different phases of igneous activity took place in Egypt during the Mesozoic and the Cenozoic and oriented samples were collected from three Cenozoic localities (Baharya oasis in the Western Desert, Abu Had in the Eastern Desert and Quseir along the Red Sea coast), and four Cretaceous localities (Toshki & Abu Simbel south of Aswan, and Shalaten & Abu Shihat along the Red Sea coast). Rock magnetic properties of the samples indicate magnetite and titanomagnetite as the main carrier of the remanent magnetization. Following stepwise demagnetization, characteristic remanent directions were identified only for 62% of the samples, a fairly low rate for that type of samples, and 8 new paleomagnetic poles were calculated. All our Cenozoic poles fall clearly off Master Polar Wander Paths proposed for South Africa. Therefore, all paleomagnetic results, previously published for Egypt, were compiled from Cretaceous to Quaternary. The published poles largely overlap, blurring the Egyptian Apparent Polar Wander Path. A new analysis at the site level was then carried out. Only poles having a kappa larger than 50 were selected, and new pole positions were calculated by area and by epoch, when at least 3 sites were available. Even though the selection drastically reduced the number of considered poles, it allows definition of a reliable Cenozoic apparent polar wander trend for Egypt that differs from the South African Master Polar Wander Path by about 10-15 °. If the Cretaceous igneous poles are in good agreement with the rest of the African data, the sedimentary poles plot close to the Cenozoic portion of the South African Master Polar Wander Path, a discrepancy that could be related either to inclination flattening and/or error on age and/or remagnetization in the Cenozoic.

Distribution of oceanic and continental leads in the Arabian-Nubian Shield

USGS Publications Warehouse

Stacey, J.S.; Stoeser, D.B.

1983-01-01

New common lead data for feldspar, whole-rock, and galena samples from the Arabian-Nubian Shield, together with data from previous work, can be divided into two main groups. Group I leads have oceanic (mantle) characteristics, whereas group II leads have incorporated a continental-crustal component of at least early Proterozoic age. The group I leads are found in rocks from the Red Sea Hills of Egypt and the western and southern parts of the Arabian Shield. Group II leads are found in rocks from the northeastern and eastern parts of the Arabian Shield, as well as from the southeastern Shield near Najran. They are also found in rocks to the south in Yemen, to the east in Oman, and to the west at Aswan, Egypt. This distribution of data suggests that the Arabian-Nubian Shield has an oceanic core flanked by rocks that have developed, at least in part, from older continental material. Two mechanisms are suggested by which this older lead component could have been incorporated into the late Proterozoic rocks, and each may have operated in different parts of the Shield. The older lead component either was derived directly from an underlying early Proterozoic basement or was incorporated from subducted pelagic sediments or sediments derived from an adjacent continent. New U-Pb zircon data indicate the presence of an early Proterozoic basement southeast of Jabal Dahul in the eastern Arabian Shield. These data, together with 2,000-Ma-old zircons from the Al Amar fault zone, verify the implication of the common lead data that at least a part of the eastern Arabian Shield has an older continental basement. Because continental margins are particularly favorable locations for development of ore deposits, these findings may have important economic implications, particularly for tin, tungsten, and molybdenum exploration. ?? 1983 Springer-Verlag.

Aquifer recharge, depletion, and connectivity: Inferences from GRACE, land surface models, and geochemical and geophysical data

DOE PAGES

Mohamed, Ahmed; Sultan, Mohamed; Ahmed, Mohamed; ...

2016-12-22

We used data from the Gravity Recovery and Climate Experiment (GRACE) and outputs of the CLM4.5 model to estimate recharge and depletion rates for large aquifers, investigate the connectivity of an aquifer's subbasins, and identify barriers and preferred pathways for groundwater flow within an aquifer system. The Nubian Sandstone Aquifer System and its subbasins (Dakhla, Northern Sudan Platform, and Kufra) in northeast Africa were used for demonstration purposes, and findings were tested and verified against geological, geophysical, remote sensing, geochronologic, and geochemical data. There are four major findings. (1) The average annual precipitation data over recharge areas in the southernmore » Kufra section and the Northern Sudan Platform subbasin were estimated at 54.8 km 3, and 32.8 km 3, respectively, and knowing the annual extraction rates over these two areas (similar to 0.40 ± 0.20 km 3), recharge rates were estimated at 0.78 ± 0.49 km 3/yr and 1.44 ± 0.42 km 3/yr, respectively. (2) GRACEderived groundwater depletion rates over the Dakhla subbasin and the Northern Kufra section were estimated at 4.44 ± 0.42 km 3/yr and 0.48 ± 0.32 km 3/yr, respectively. (3) The observed depletion in the southern parts of the Dakhla subbasin is apparently caused by the presence of the east- west- trending Uweinat-Aswan basement uplift, which impedes the south-to-north groundwater flow and hence reduces replenishment from recharge areas in the south. (4) A major northeast- southwest- trending shear zone (Pelusium shear system) is apparently providing a preferred groundwater flow pathway from the Kufra to the Dakhla subbasin. Thus, inte-grated approach provides a replicable and cost-effective model for better understanding of the hydrogeologic setting of large aquifers worldwide and for optimum management of these groundwater resources.« less

Aquifer recharge, depletion, and connectivity: Inferences from GRACE, land surface models, and geochemical and geophysical data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohamed, Ahmed; Sultan, Mohamed; Ahmed, Mohamed

We used data from the Gravity Recovery and Climate Experiment (GRACE) and outputs of the CLM4.5 model to estimate recharge and depletion rates for large aquifers, investigate the connectivity of an aquifer's subbasins, and identify barriers and preferred pathways for groundwater flow within an aquifer system. The Nubian Sandstone Aquifer System and its subbasins (Dakhla, Northern Sudan Platform, and Kufra) in northeast Africa were used for demonstration purposes, and findings were tested and verified against geological, geophysical, remote sensing, geochronologic, and geochemical data. There are four major findings. (1) The average annual precipitation data over recharge areas in the southernmore » Kufra section and the Northern Sudan Platform subbasin were estimated at 54.8 km 3, and 32.8 km 3, respectively, and knowing the annual extraction rates over these two areas (similar to 0.40 ± 0.20 km 3), recharge rates were estimated at 0.78 ± 0.49 km 3/yr and 1.44 ± 0.42 km 3/yr, respectively. (2) GRACEderived groundwater depletion rates over the Dakhla subbasin and the Northern Kufra section were estimated at 4.44 ± 0.42 km 3/yr and 0.48 ± 0.32 km 3/yr, respectively. (3) The observed depletion in the southern parts of the Dakhla subbasin is apparently caused by the presence of the east- west- trending Uweinat-Aswan basement uplift, which impedes the south-to-north groundwater flow and hence reduces replenishment from recharge areas in the south. (4) A major northeast- southwest- trending shear zone (Pelusium shear system) is apparently providing a preferred groundwater flow pathway from the Kufra to the Dakhla subbasin. Thus, inte-grated approach provides a replicable and cost-effective model for better understanding of the hydrogeologic setting of large aquifers worldwide and for optimum management of these groundwater resources.« less

High-Q and highly reproducible microdisks and microlasers.

PubMed

Zhang, Nan; Wang, Yujie; Sun, Wenzhao; Liu, Shuai; Huang, Can; Jiang, Xiaoshun; Xiao, Min; Xiao, Shumin; Song, Qinghai

2018-01-25

High quality (Q) factor microdisks are fundamental building blocks of on-chip integrated photonic circuits and biological sensors. The resonant modes in microdisks circulate near their boundaries, making their performances strongly dependent upon surface roughness. Surface-tension-induced microspheres and microtoroids are superior to other dielectric microdisks when comparing Q factors. However, most photonic materials such as silicon and negative photoresists are hard to be reflowed and thus the realizations of high-Q microdisks are strongly dependent on electron-beam lithography. Herein, we demonstrate a robust, cost-effective, and highly reproducible technique to fabricate ultrahigh-Q microdisks. By using silica microtoroids as masks, we have successfully replicated their ultrasmooth boundaries in a photoresist via anisotropic dry etching. The experimentally recorded Q factors of passive microdisks can be as large as 1.5 × 10 6 . Similarly, ultrahigh Q microdisk lasers have also been replicated in dye-doped polymeric films. The laser linewidth is only 8 pm, which is limited by the spectrometer and is much narrower than that in previous reports. Meanwhile, high-Q deformed microdisks have also been fabricated by controlling the shape of microtoroids, making the internal ray dynamics and external directional laser emissions controllable. Interestingly, this technique also applies to other materials. Silicon microdisks with Q > 10 6 have been experimentally demonstrated with a similar process. We believe this research will be important for the advances of high-Q micro-resonators and their applications.

High pressure and high temperature apparatus

DOEpatents

Voronov, Oleg A.

2005-09-13

A design for high pressure/high temperature apparatus and reaction cell to achieve .about.30 GPa pressure in .about.1 cm volume and .about.100 GPa pressure in .about.1 mm volumes and 20-5000.degree. C. temperatures in a static regime. The device includes profiled anvils (28) action on a reaction cell (14, 16) containing the material (26) to be processed. The reaction cell includes a heater (18) surrounded by insulating layers and screens. Surrounding the anvils are cylindrical inserts and supporting rings (30-48) whose hardness increases towards the reaction cell. These volumes may be increased considerably if applications require it, making use of presses that have larger loading force capability, larger frames and using larger anvils.

High speed high dynamic range high accuracy measurement system

DOEpatents

Deibele, Craig E.; Curry, Douglas E.; Dickson, Richard W.; Xie, Zaipeng

2016-11-29

A measuring system includes an input that emulates a bandpass filter with no signal reflections. A directional coupler connected to the input passes the filtered input to electrically isolated measuring circuits. Each of the measuring circuits includes an amplifier that amplifies the signal through logarithmic functions. The output of the measuring system is an accurate high dynamic range measurement.

High-Tuition, High-Loan Financing: Economic Segregation in Postsecondary Education

ERIC Educational Resources Information Center

Lillis, Michael P.

2008-01-01

Within the past 2 decades, the education services industry has been characterized as going through a period of high tuition with an increased reliance on the use of loan financing. This study examines the impact of this high-tuition, high-loan approach, especially as it relates to the role of socioeconomic status on educational choice within…

High sustained +Gz acceleration: physiological adaptation to high-G tolerance

NASA Technical Reports Server (NTRS)

Convertino, V. A.

1998-01-01

Since the early 1940s, a significant volume of research has been conducted in an effort to describe the impact of acute exposures to high-G acceleration on cardiovascular mechanisms responsible to maintaining cerebral perfusion and conscious in high performance aircraft pilots during aerial combat maneuvers. The value of understanding hemodynamic characteristics that underlie G-induced loss of consciousness has been instrumental in the evolution of optimal technology development (e.g., G-suits, positive pressure breathing, COMBAT EDGE, etc.) and pilot training (e.g., anti-G straining maneuvers). Although the emphasis of research has been placed on the development of protection against acute high +Gz acceleration effects, recent observations suggest that adaptation of cardiovascular mechanism associated with blood pressure regulation may contribute to a protective 'G-training' effect. Regular training at high G enhances G tolerance in humans, rats, guinea pigs, and dogs while prolonged layoff from exposure in high G profiles (G-layoff) can result in reduced G endurance. It seems probable that adaptations in physiological functions following chronically-repeated high G exposure (G training) or G-layoff could have significant impacts on performance during sustained high-G acceleration since protective technology such as G-suits and anit-G straining maneuvers are applied consistently during these periods of training. The purpose of this paper is to present a review of new data from three experiments that support the notion that repeated exposure on a regular basis to high sustained +Gz acceleration induces significant physiological adaptations which are associated with improved blood pressure regulation and subsequent protection of cerebral perfusion during orthostatic challenges.

High-fat, high-fructose, high-cholesterol feeding causes severe NASH and cecal microbiota dysbiosis in juvenile Ossabaw swine

USDA-ARS?s Scientific Manuscript database

Pediatric obesity and nonalcoholic steatohepatitis (NASH) are on the rise in industrialized countries, yet our ability to mechanistically examine this relationship is limited by the lack of a suitable higher animal models. Here, we examined the effects of high-fat, high-fructose corn syrup, high-cho...

High power, high beam quality regenerative amplifier

DOEpatents

Hackel, L.A.; Dane, C.B.

1993-08-24

A regenerative laser amplifier system generates high peak power and high energy per pulse output beams enabling generation of X-rays used in X-ray lithography for manufacturing integrated circuits. The laser amplifier includes a ring shaped optical path with a limited number of components including a polarizer, a passive 90 degree phase rotator, a plurality of mirrors, a relay telescope, and a gain medium, the components being placed close to the image plane of the relay telescope to reduce diffraction or phase perturbations in order to limit high peak intensity spiking. In the ring, the beam makes two passes through the gain medium for each transit of the optical path to increase the amplifier gain to loss ratio. A beam input into the ring makes two passes around the ring, is diverted into an SBS phase conjugator and proceeds out of the SBS phase conjugator back through the ring in an equal but opposite direction for two passes, further reducing phase perturbations. A master oscillator inputs the beam through an isolation cell (Faraday or Pockels) which transmits the beam into the ring without polarization rotation. The isolation cell rotates polarization only in beams proceeding out of the ring to direct the beams out of the amplifier. The diffraction limited quality of the input beam is preserved in the amplifier so that a high power output beam having nearly the same diffraction limited quality is produced.

High power, high beam quality regenerative amplifier

DOEpatents

Hackel, Lloyd A.; Dane, Clifford B.

1993-01-01

A regenerative laser amplifier system generates high peak power and high energy per pulse output beams enabling generation of X-rays used in X-ray lithography for manufacturing integrated circuits. The laser amplifier includes a ring shaped optical path with a limited number of components including a polarizer, a passive 90 degree phase rotator, a plurality of mirrors, a relay telescope, and a gain medium, the components being placed close to the image plane of the relay telescope to reduce diffraction or phase perturbations in order to limit high peak intensity spiking. In the ring, the beam makes two passes through the gain medium for each transit of the optical path to increase the amplifier gain to loss ratio. A beam input into the ring makes two passes around the ring, is diverted into an SBS phase conjugator and proceeds out of the SBS phase conjugator back through the ring in an equal but opposite direction for two passes, further reducing phase perturbations. A master oscillator inputs the beam through an isolation cell (Faraday or Pockels) which transmits the beam into the ring without polarization rotation. The isolation cell rotates polarization only in beams proceeding out of the ring to direct the beams out of the amplifier. The diffraction limited quality of the input beam is preserved in the amplifier so that a high power output beam having nearly the same diffraction limited quality is produced.

High Blood Pressure

MedlinePlus

... normal blood pressure 140/90 or higher is high blood pressure Between 120 and 139 for the top number, ... prehypertension. Prehypertension means you may end up with high blood pressure, unless you take steps to prevent it. High ...

High-frequency and high-quality silicon carbide optomechanical microresonators

PubMed Central

Lu, Xiyuan; Lee, Jonathan Y.; Lin, Qiang

2015-01-01

Silicon carbide (SiC) exhibits excellent material properties attractive for broad applications. We demonstrate the first SiC optomechanical microresonators that integrate high mechanical frequency, high mechanical quality, and high optical quality into a single device. The radial-breathing mechanical mode has a mechanical frequency up to 1.69 GHz with a mechanical Q around 5500 in atmosphere, which corresponds to a fm · Qm product as high as 9.47 × 1012 Hz. The strong optomechanical coupling allows us to efficiently excite and probe the coherent mechanical oscillation by optical waves. The demonstrated devices, in combination with the superior thermal property, chemical inertness, and defect characteristics of SiC, show great potential for applications in metrology, sensing, and quantum photonics, particularly in harsh environments that are challenging for other device platforms. PMID:26585637

High-throughput machining using a high-average power ultrashort pulse laser and high-speed polygon scanner

NASA Astrophysics Data System (ADS)

Schille, Joerg; Schneider, Lutz; Streek, André; Kloetzer, Sascha; Loeschner, Udo

2016-09-01

High-throughput ultrashort pulse laser machining is investigated on various industrial grade metals (aluminum, copper, and stainless steel) and Al2O3 ceramic at unprecedented processing speeds. This is achieved by using a high-average power picosecond laser in conjunction with a unique, in-house developed polygon mirror-based biaxial scanning system. Therefore, different concepts of polygon scanners are engineered and tested to find the best architecture for high-speed and precision laser beam scanning. In order to identify the optimum conditions for efficient processing when using high-average laser powers, the depths of cavities made in the samples by varying the processing parameter settings are analyzed and, from the results obtained, the characteristic removal values are specified. For overlapping pulses of optimum fluence, the removal rate is as high as 27.8 mm3/min for aluminum, 21.4 mm3/min for copper, 15.3 mm3/min for stainless steel, and 129.1 mm3/min for Al2O3, when a laser beam of 187 W average laser powers irradiates. On stainless steel, it is demonstrated that the removal rate increases to 23.3 mm3/min when the laser beam is very fast moving. This is thanks to the low pulse overlap as achieved with 800 m/s beam deflection speed; thus, laser beam shielding can be avoided even when irradiating high-repetitive 20-MHz pulses.

Analysis of transistor and snubber turn-off dynamics in high-frequency high-voltage high-power converters

NASA Technical Reports Server (NTRS)

Wilson, P. M.; Wilson, T. G.; Owen, H. A., Jr.

1982-01-01

Dc to dc converters which operate reliably and efficiently at switching frequencies high enough to effect substantial reductions in the size and weight of converter energy storage elements are studied. A two winding current or voltage stepup (buck boost) dc-to-dc converter power stage submodule designed to operate in the 2.5-kW range, with an input voltage range of 110 to 180 V dc, and an output voltage of 250 V dc is emphasized. In order to assess the limitations of present day component and circuit technologies, a design goal switching frequency of 10 kHz was maintained. The converter design requirements represent a unique combination of high frequency, high voltage, and high power operation. The turn off dynamics of the primary circuit power switching transistor and its associated turn off snubber circuitry are investigated.

Analysis of transistor and snubber turn-off dynamics in high-frequency high-voltage high-power converters

NASA Astrophysics Data System (ADS)

Wilson, P. M.; Wilson, T. G.; Owen, H. A., Jr.

Dc to dc converters which operate reliably and efficiently at switching frequencies high enough to effect substantial reductions in the size and weight of converter energy storage elements are studied. A two winding current or voltage stepup (buck boost) dc-to-dc converter power stage submodule designed to operate in the 2.5-kW range, with an input voltage range of 110 to 180 V dc, and an output voltage of 250 V dc is emphasized. In order to assess the limitations of present day component and circuit technologies, a design goal switching frequency of 10 kHz was maintained. The converter design requirements represent a unique combination of high frequency, high voltage, and high power operation. The turn off dynamics of the primary circuit power switching transistor and its associated turn off snubber circuitry are investigated.

High-Density, High-Bandwidth, Multilevel Holographic Memory

NASA Technical Reports Server (NTRS)

Chao, Tien-Hsin

2008-01-01

A proposed holographic memory system would be capable of storing data at unprecedentedly high density, and its data transfer performance in both reading and writing would be characterized by exceptionally high bandwidth. The capabilities of the proposed system would greatly exceed even those of a state-of-the art memory system, based on binary holograms (in which each pixel value represents 0 or 1), that can hold .1 terabyte of data and can support a reading or writing rate as high as 1 Gb/s. The storage capacity of the state-of-theart system cannot be increased without also increasing the volume and mass of the system. However, in principle, the storage capacity could be increased greatly, without significantly increasing the volume and mass, if multilevel holograms were used instead of binary holograms. For example, a 3-bit (8-level) hologram could store 8 terabytes, or an 8-bit (256-level) hologram could store 256 terabytes, in a system having little or no more size and mass than does the state-of-the-art 1-terabyte binary holographic memory. The proposed system would utilize multilevel holograms. The system would include lasers, imaging lenses and other beam-forming optics, a block photorefractive crystal wherein the holograms would be formed, and two multilevel spatial light modulators in the form of commercially available deformable-mirror-device spatial light modulators (DMDSLMs) made for use in high speed input conversion of data up to 12 bits. For readout, the system would also include two arrays of complementary metal oxide/semiconductor (CMOS) photodetectors matching the spatial light modulators. The system would further include a reference-beam sterring device (equivalent of a scanning mirror), containing no sliding parts, that could be either a liquid-crystal phased-array device or a microscopic mirror actuated by a high-speed microelectromechanical system. Time-multiplexing and the multilevel nature of the DMDSLM would be exploited to enable writing

High performance aluminum–cerium alloys for high-temperature applications

DOE PAGES

Sims, Zachary C.; Rios, Orlando R.; Weiss, David; ...

2017-08-01

Light-weight high-temperature alloys are important to the transportation industry where weight, cost, and operating temperature are major factors in the design of energy efficient vehicles. Aluminum alloys fill this gap economically but lack high-temperature mechanical performance. Alloying aluminum with cerium creates a highly castable alloy, compatible with traditional aluminum alloy additions, that exhibits dramatically improved high-temperature performance. These compositions display a room temperature ultimate tensile strength of 400 MPa and yield strength of 320 MPa, with 80% mechanical property retention at 240 °C. A mechanism is identified that addresses the mechanical property stability of the Al-alloys to at least 300more » °C and their microstructural stability to above 500 °C which may enable applications without the need for heat treatment. Lastly, neutron diffraction under load provides insight into the unusual mechanisms driving the mechanical strength.« less

High performance systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vigil, M.B.

1995-03-01

This document provides a written compilation of the presentations and viewgraphs from the 1994 Conference on High Speed Computing given at the High Speed Computing Conference, {open_quotes}High Performance Systems,{close_quotes} held at Gleneden Beach, Oregon, on April 18 through 21, 1994.

High-Capacity Cathode Material with High Voltage for Li-Ion Batteries

DOE PAGES

Shi, Ji -Lei; Xiao, Dong -Dong; Ge, Mingyuan; ...

2018-01-15

Electrochemical energy storage devices with a high energy density are an important technology in modern society, especially for electric vehicles. The most effective approach to improve the energy density of batteries is to search for high-capacity electrode materials. According to the concept of energy quality, a high-voltage battery delivers a highly useful energy, thus providing a new insight to improve energy density. Based on this concept, a novel and successful strategy to increase the energy density and energy quality by increasing the discharge voltage of cathode materials and preserving high capacity is proposed. The proposal is realized in high-capacity Li-richmore » cathode materials. The average discharge voltage is increased from 3.5 to 3.8 V by increasing the nickel content and applying a simple after-treatment, and the specific energy is improved from 912 to 1033 Wh kg-1. The current work provides an insightful universal principle for developing, designing, and screening electrode materials for high energy density and energy quality.« less

High-Capacity Cathode Material with High Voltage for Li-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Ji -Lei; Xiao, Dong -Dong; Ge, Mingyuan

Electrochemical energy storage devices with a high energy density are an important technology in modern society, especially for electric vehicles. The most effective approach to improve the energy density of batteries is to search for high-capacity electrode materials. According to the concept of energy quality, a high-voltage battery delivers a highly useful energy, thus providing a new insight to improve energy density. Based on this concept, a novel and successful strategy to increase the energy density and energy quality by increasing the discharge voltage of cathode materials and preserving high capacity is proposed. The proposal is realized in high-capacity Li-richmore » cathode materials. The average discharge voltage is increased from 3.5 to 3.8 V by increasing the nickel content and applying a simple after-treatment, and the specific energy is improved from 912 to 1033 Wh kg-1. The current work provides an insightful universal principle for developing, designing, and screening electrode materials for high energy density and energy quality.« less

High-efficiency water-loaded microwave antenna in ultra-high-frequency band

NASA Astrophysics Data System (ADS)

Gong, Zilun; Bartone, Chris; Yang, Fuyi; Yao, Jie

2018-03-01

High-index dielectrics are widely used in microwave antennas to control the radiation characteristics. Liquid water, with a high dielectric index at microwave frequency, is an interesting material to achieving tunable functionalities. Here, we demonstrate a water-loaded microwave antenna system that has high loss-tolerance and wideband tunability enabled by fluidity. Our simulation and experimental results show that the resonance frequency can be effectively tuned by the size of loading water. Furthermore, the antenna systems with water loading can achieve high radiation efficiency (>90%) in the ultra-high-frequency (0.3-3 GHz) band. This work brings about opportunities in realistic tunable microwave antenna designs enabled by liquid.

High-Power, High-Intensity Laser Propagation and Interactions

DTIC Science & Technology

2014-03-10

wave Brillouin mixing [89,90]. transmitted beam is phase conjugated target initial wave front nn  1 turbulent air Figure 14. Using phase and...discussed in connection with both high-power and high-intensity lasers is propagation in a turbulent atmosphere . Laser propagation in atmospheric ... turbulence can results in beam centroid wander, spreading and intensity scintillation. A phase conjugation technique to mitigate the effects of atmospheric

High altitude illness

PubMed

Hartman-Ksycińska, Anna; Kluz-Zawadzka, Jolanta; Lewandowski, Bogumił

High-altitude illness is a result of prolonged high-altitude exposure of unacclimatized individuals. The illness is seen in the form of acute mountain sickness (AMS) which if not treated leads to potentially life-threatening high altitude pulmonary oedema and high-altitude cerebral oedema. Medical problems are caused by hypobaric hypoxia stimulating hypoxia-inducible factor (HIF) release. As a result, the central nervous system, circulation and respiratory system function impairment occurs. The most important factor in AMS treatment is acclimatization, withdrawing further ascent and rest or beginning to descent; oxygen supplementation, and pharmacological intervention, and, if available, a portable hyperbaric chamber. Because of the popularity of high-mountain sports and tourism better education of the population at risk is essential.

Code TESLA for Modeling and Design of High-Power High-Efficiency Klystrons

DTIC Science & Technology

2011-03-01

CODE TESLA FOR MODELING AND DESIGN OF HIGH - POWER HIGH -EFFICIENCY KLYSTRONS * I.A. Chernyavskiy, SAIC, McLean, VA 22102, U.S.A. S.J. Cooke, B...and multiple-beam klystrons as high - power RF sources. These sources are widely used or proposed to be used in accelerators in the future. Comparison...of TESLA modelling results with experimental data for a few multiple-beam klystrons are shown. INTRODUCTION High - power and high -efficiency

A Promising New Class of High-Temperature Alloys: Eutectic High-Entropy Alloys

PubMed Central

Lu, Yiping; Dong, Yong; Guo, Sheng; Jiang, Li; Kang, Huijun; Wang, Tongmin; Wen, Bin; Wang, Zhijun; Jie, Jinchuan; Cao, Zhiqiang; Ruan, Haihui; Li, Tingju

2014-01-01

High-entropy alloys (HEAs) can have either high strength or high ductility, and a simultaneous achievement of both still constitutes a tough challenge. The inferior castability and compositional segregation of HEAs are also obstacles for their technological applications. To tackle these problems, here we proposed a novel strategy to design HEAs using the eutectic alloy concept, i.e. to achieve a microstructure composed of alternating soft fcc and hard bcc phases. As a manifestation of this concept, an AlCoCrFeNi2.1 (atomic portion) eutectic high-entropy alloy (EHEA) was designed. The as-cast EHEA possessed a fine lamellar fcc/B2 microstructure, and showed an unprecedented combination of high tensile ductility and high fracture strength at room temperature. The excellent mechanical properties could be kept up to 700°C. This new alloy design strategy can be readily adapted to large-scale industrial production of HEAs with simultaneous high fracture strength and high ductility. PMID:25160691

The High Temperature Tensile and Creep Behaviors of High Entropy Superalloy.

PubMed

Tsao, Te-Kang; Yeh, An-Chou; Kuo, Chen-Ming; Kakehi, Koji; Murakami, Hideyuki; Yeh, Jien-Wei; Jian, Sheng-Rui

2017-10-04

This article presents the high temperature tensile and creep behaviors of a novel high entropy alloy (HEA). The microstructure of this HEA resembles that of advanced superalloys with a high entropy FCC matrix and L1 2 ordered precipitates, so it is also named as "high entropy superalloy (HESA)". The tensile yield strengths of HESA surpass those of the reported HEAs from room temperature to elevated temperatures; furthermore, its creep resistance at 982 °C can be compared to those of some Ni-based superalloys. Analysis on experimental results indicate that HESA could be strengthened by the low stacking-fault energy of the matrix, high anti-phase boundary energy of the strengthening precipitate, and thermally stable microstructure. Positive misfit between FCC matrix and precipitate has yielded parallel raft microstructure during creep at 982 °C, and the creep curves of HESA were dominated by tertiary creep behavior. To the best of authors' knowledge, this article is the first to present the elevated temperature tensile creep study on full scale specimens of a high entropy alloy, and the potential of HESA for high temperature structural application is discussed.

High-pressure-assisted synthesis of high-volume ZnGeP2 polycrystalline

NASA Astrophysics Data System (ADS)

Huang, Changbao; Wu, Haixin; Xiao, Ruichun; Chen, Shijing; Ma, Jiaren

2018-06-01

The pnictide and chalcogenide semiconductors are promising materials for the applications in the field of photoelectric. High-purity and high-volume polycrystalline required in the real-world applications is hard to be synthesized due to the high vapor pressure of phosphorus and sulfur components at high temperature. A new high-pressure-resisted method was used to investigate the synthesis of the nonlinear-optical semiconductor ZnGeP2. The high-purity ZnGeP2 polycrystalline material of approximately 500 g was synthesized in one run, which enables the preparation of nominally stoichiometric material. Since increasing internal pressure resistance of quartz crucible and reducing the reaction space, the high-pressure-resisted method can be used to rapidly synthesize other pnictide and chalcogenide semiconductors and control the components ratio.

High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Turnquist, Norman; Qi, Xuele; Raminosoa, Tsarafidy

2013-12-20

This report summarizes the progress made during the April 01, 2010 – December 30, 2013 period under Cooperative Agreement DE-EE0002752 for the U.S. Department of Energy entitled “High-Temperature-High-Volume Lifting for Enhanced Geothermal Systems.” The overall objective of this program is to advance the technology for well fluids lifting systems to meet the foreseeable pressure, temperature, and longevity needs of the Enhanced Geothermal Systems (EGS) industry for the coming ten years. In this program, lifting system requirements for EGS wells were established via consultation with industry experts and site visits. A number of artificial lift technologies were evaluated with regard tomore » their applicability to EGS applications; it was determined that a system based on electric submersible pump (ESP) technology was best suited to EGS. Technical barriers were identified and a component-level technology development program was undertaken to address each barrier, with the most challenging being the development of a power-dense, small diameter motor that can operate reliably in a 300°C environment for up to three years. Some of the targeted individual component technologies include permanent magnet motor construction, high-temperature insulation, dielectrics, bearings, seals, thrust washers, and pump impellers/diffusers. Advances were also made in thermal management of electric motors. In addition to the overall system design for a full-scale EGS application, a subscale prototype was designed and fabricated. Like the full-scale design, the subscale prototype features a novel “flow-through-the-bore” permanent magnet electric motor that combines the use of high temperature materials with an internal cooling scheme that limits peak internal temperatures to <330°C. While the full-scale high-volume multi-stage pump is designed to lift up to 80 kg/s of process water, the subscale prototype is based on a production design that can pump 20 kg/s and has been

Development of high pressure-high vacuum-high conductance piston valve for gas-filled radiation detectors

NASA Astrophysics Data System (ADS)

Prasad, D. N.; Ayyappan, R.; Kamble, L. P.; Singh, J. P.; Muralikrishna, L. V.; Alex, M.; Balagi, V.; Mukhopadhyay, P. K.

2008-05-01

Gas-filled radiation detectors need gas filling at pressures that range from few cms of mercury to as high as 25kg/cm2 at room temperature. Before gas-filling these detectors require evacuation to a vacuum of the order of ~1 × 10-5 mbar. For these operations of evacuation and gas filling a system consisting of a vacuum pump with a high vacuum gauge, gas cylinder with a pressure gauge and a valve is used. The valve has to meet the three requirements of compatibility with high-pressure and high vacuum and high conductance. A piston valve suitable for the evacuation and gas filling of radiation detectors has been designed and fabricated to meet the above requirements. The stainless steel body (80mm×160mm overall dimensions) valve with a piston arrangement has a 1/2 inch inlet/outlet opening, neoprene/viton O-ring at piston face & diameter for sealing and a knob for opening and closing the valve. The piston movement mechanism is designed to have minimum wear of sealing O-rings. The valve has been hydrostatic pressure tested up to 75bars and has Helium leak rate of less than 9.6×10-9 m bar ltr/sec in vacuum mode and 2×10-7 mbar ltr/sec in pressure mode. As compared to a commercial diaphragm valve, which needed 3 hours to evacuate a 7 litre chamber to 2.5×10-5 mbar, the new valve achieved vacuum 7.4×10-6mbar in the same time under the same conditions.

Personality Types of Illinois Elementary Principals in High-Poverty, High-Performing Schools

ERIC Educational Resources Information Center

Hollowell, Daniel R.

2016-01-01

The socio-economic achievement gap is prevalent in schools across the country. There are many high-poverty, high-performing schools that have been successful in closing this achievement gap. This study investigated 30 Illinois elementary school principals from high-poverty, high-achieving schools. Principals were given the Myers-Briggs Type…

Success with High School Allotment: Three High Schools' Rise to Exemplary

ERIC Educational Resources Information Center

Bevers, James Walter

2012-01-01

This study was implemented to investigate how three Texas high school campuses improved their campus accountability ratings using the High School Allotment (HSA) funding. Three high schools were selected based on criteria, including campus size, ethnic breakdown of student population, use of HSA finding, and improvement in the campus…

Progress with High-Field Superconducting Magnets for High-Energy Colliders

NASA Astrophysics Data System (ADS)

Apollinari, Giorgio; Prestemon, Soren; Zlobin, Alexander V.

2015-10-01

One of the possible next steps for high-energy physics research relies on a high-energy hadron or muon collider. The energy of a circular collider is limited by the strength of bending dipoles, and its maximum luminosity is determined by the strength of final focus quadrupoles. For this reason, the high-energy physics and accelerator communities have shown much interest in higher-field and higher-gradient superconducting accelerator magnets. The maximum field of NbTi magnets used in all present high-energy machines, including the LHC, is limited to ˜10 T at 1.9 K. Fields above 10 T became possible with the use of Nb3Sn superconductors. Nb3Sn accelerator magnets can provide operating fields up to ˜15 T and can significantly increase the coil temperature margin. Accelerator magnets with operating fields above 15 T require high-temperature superconductors. This review discusses the status and main results of Nb3Sn accelerator magnet research and development and work toward 20-T magnets.

Progress with high-field superconducting magnets for high-energy colliders

DOE PAGES

Apollinari, Giorgio; Prestemon, Soren; Zlobin, Alexander V.

2015-10-01

One of the possible next steps for high-energy physics research relies on a high-energy hadron or muon collider. The energy of a circular collider is limited by the strength of bending dipoles, and its maximum luminosity is determined by the strength of final focus quadrupoles. For this reason, the high-energy physics and accelerator communities have shown much interest in higher-field and higher-gradient superconducting accelerator magnets. The maximum field of NbTi magnets used in all present high-energy machines, including the LHC, is limited to ~10 T at 1.9 K. Fields above 10 T became possible with the use of Nbmore » $$_3$$Sn superconductors. Nb$$_3$$Sn accelerator magnets can provide operating fields up to ~15 T and can significantly increase the coil temperature margin. Accelerator magnets with operating fields above 15 T require high-temperature superconductors. Furthermore, this review discusses the status and main results of Nb$$_3$$Sn accelerator magnet research and development and work toward 20-T magnets.« less

Status of high polarization DC high voltage Gallium Arsenide photoelectron guns

DOE Office of Scientific and Technical Information (OSTI.GOV)

M. Poelker, P. Adderley, J. Brittian, J. Clark, J. Grames, J. Hansknecht, J. McCarter, M. Stutzman, R. Suleiman, K. Surles-Law

2008-01-01

Users receive very high beam polarization from reliable GaAs photoelectron guns at facilities worldwide. Satisfaction with beam quality (and a number of lab closures) has reduced the level of polarized source R&D from the heyday of 1990s. However, new experiments and new accelerators proposals including high current unpolarized machines, require GaAs photoguns with capabilities that exceed today's state of the art. This submission describes the capabilities of today's high- polarization DC high voltage GaAs photoguns and discusses issues that must be addressed to meet new demands.

Self-Esteem of Junior High and High School Students.

ERIC Educational Resources Information Center

Lee, Kimberly E.

The purpose of this thesis was to investigate the self-esteem of junior high and high school students. The independent variables investigated were quality of family life, birth order, family size, maternal employment, grade level and family structure. The dependent variables were the self-esteem scores from the following sub-scales of the Texas…

Beating the Odds: High Performing, Small High-Schools in the Rural South

ERIC Educational Resources Information Center

Rural School and Community Trust, 2004

2004-01-01

The Southern Rural High School Study Initiative seeks to identify high performing rural high schools in the South, engage education leaders in the region in analyzing the challenges faced by these schools and consider the public policies that might serve to transfer the lessons and strategies used by these schools to other small rural high schools…

High power, high contrast hybrid femtosecond laser systems

NASA Astrophysics Data System (ADS)

Dabu, Razvan

2017-06-01

For many research applications a very high laser intensity of more than 1022 W/cm2 in the focused beam is required. If a laser intensity of about 1011W/cm2 is reached on the target before the main laser pulse, the generated pre-plasma disturbs the experiment. High power femtosecond lasers must be tightly focused to get high intensity and in the same time must have a high enough intensity contrast of the temporally compressed amplified pulses. Reaching an intensity contrast in the range of 1012 represents a challenging task for a Ti:sapphire CPA laser. Hybrid femtosecond lasers combine optical parametric chirped pulsed amplification (OPCPA) in nonlinear crystals with the chirped pulse amplification (CPA) in laser active media. OPCPA provides large amplification spectral bandwidth and improves the intensity contrast of the amplified pulses. A key feature of these systems consists in the adaptation of the parametric amplification phase-matching bandwidth of nonlinear crystals to the spectral gain bandwidth of laser amplifying Ti:sapphire crystals. OPCPA in BBO crystals up to mJ energy level in the laser Front-End, followed by CPA up to ten/hundred Joules in large aperture Ti:sapphire crystals, represents a suitable solution for PW-class femtosecond lasers. The configuration and expected output beam characteristics of the hybrid amplification 2 × 10 PW ELI-NP laser are described.

Resistance Exercise Attenuates High-Fructose, High-Fat-Induced Postprandial Lipemia

PubMed Central

Wilburn, Jessie R; Bourquin, Jeffrey; Wysong, Andrea; Melby, Christopher L

2015-01-01

INTRODUCTION Meals rich in both fructose and fat are commonly consumed by many Americans, especially young men, which can produce a significant postprandial lipemic response. Increasing evidence suggests that aerobic exercise can attenuate the postprandial increase in plasma triacylglycerols (TAGs) in response to a high-fat or a high-fructose meal. However, it is unknown if resistance exercise can dampen the postprandial lipemic response to a meal rich in both fructose and fat. METHODS Eight apparently healthy men (Mean ± SEM; age = 27 ± 2 years) participated in a crossover study to examine the effects of acute resistance exercise on next-day postprandial lipemia resulting from a high-fructose, high-fat meal. Participants completed three separate two-day conditions in a random order: (1) EX-COMP: a full-body weightlifting workout with the provision of additional kilocalories to compensate for the estimated net energy cost of exercise on day 1, followed by the consumption of a high-fructose, high-fat liquid test meal the next morning (day 2) (~600 kcal) and the determination of the plasma glucose, lactate, insulin, and TAG responses during a six-hour postprandial period; (2) EX-DEF: same condition as EX-COMP but without exercise energy compensation on day 1; and (3) CON: no exercise control. RESULTS The six-hour postprandial plasma insulin and lactate responses did not differ between conditions. However, the postprandial plasma TAG concentrations were 16.5% and 24.4% lower for EX-COMP (551.0 ± 80.5 mg/dL × 360 minutes) and EX-DEF (499.4 ± 73.5 mg/dL × 360 minutes), respectively, compared to CON (660.2 ± 95.0 mg/dL × 360 minutes) (P < 0.05). CONCLUSIONS A single resistance exercise bout, performed ~15 hours prior to a high-fructose, high-fat meal, attenuated the postprandial TAG response, as compared to a no-exercise control condition, in healthy, resistance-trained men. PMID:26508874

Resistance Exercise Attenuates High-Fructose, High-Fat-Induced Postprandial Lipemia.

PubMed

Wilburn, Jessie R; Bourquin, Jeffrey; Wysong, Andrea; Melby, Christopher L

2015-01-01

Meals rich in both fructose and fat are commonly consumed by many Americans, especially young men, which can produce a significant postprandial lipemic response. Increasing evidence suggests that aerobic exercise can attenuate the postprandial increase in plasma triacylglycerols (TAGs) in response to a high-fat or a high-fructose meal. However, it is unknown if resistance exercise can dampen the postprandial lipemic response to a meal rich in both fructose and fat. Eight apparently healthy men (Mean ± SEM; age = 27 ± 2 years) participated in a crossover study to examine the effects of acute resistance exercise on next-day postprandial lipemia resulting from a high-fructose, high-fat meal. Participants completed three separate two-day conditions in a random order: (1) EX-COMP: a full-body weightlifting workout with the provision of additional kilocalories to compensate for the estimated net energy cost of exercise on day 1, followed by the consumption of a high-fructose, high-fat liquid test meal the next morning (day 2) (~600 kcal) and the determination of the plasma glucose, lactate, insulin, and TAG responses during a six-hour postprandial period; (2) EX-DEF: same condition as EX-COMP but without exercise energy compensation on day 1; and (3) CON: no exercise control. The six-hour postprandial plasma insulin and lactate responses did not differ between conditions. However, the postprandial plasma TAG concentrations were 16.5% and 24.4% lower for EX-COMP (551.0 ± 80.5 mg/dL × 360 minutes) and EX-DEF (499.4 ± 73.5 mg/dL × 360 minutes), respectively, compared to CON (660.2 ± 95.0 mg/dL × 360 minutes) (P < 0.05). A single resistance exercise bout, performed ~15 hours prior to a high-fructose, high-fat meal, attenuated the postprandial TAG response, as compared to a no-exercise control condition, in healthy, resistance-trained men.

Simple Motor Control Concept Results High Efficiency at High Velocities

NASA Astrophysics Data System (ADS)

Starin, Scott; Engel, Chris

2013-09-01

The need for high velocity motors in space applications for reaction wheels and detectors has stressed the limits of Brushless Permanent Magnet Motors (BPMM). Due to inherent hysteresis core losses, conventional BPMMs try to balance the need for torque verses hysteresis losses. Cong-less motors have significantly less hysteresis losses but suffer from lower efficiencies. Additionally, the inherent low inductance in cog-less motors result in high ripple currents or high switching frequencies, which lowers overall efficiency and increases performance demands on the control electronics.However, using a somewhat forgotten but fully qualified technology of Isotropic Magnet Motors (IMM), extremely high velocities may be achieved at low power input using conventional drive electronics. This paper will discuss the trade study efforts and empirical test data on a 34,000 RPM IMM.

Development of high-average-power DPSSL with high beam quality

NASA Astrophysics Data System (ADS)

Nakai, Sadao; Kanabe, Tadashi; Kawashima, Toshiyuki; Yamanaka, Masanobu; Izawa, Yasukazu; Nakatuka, Masahiro; Kandasamy, Ranganathan; Kan, Hirofumi; Hiruma, Teruo; Niino, Masayuki

2000-08-01

The recent progress of high power diode laser is opening new fields of laser and its application. We are developing high average power diode pumped solid state laser DPSSL for laser fusion power plant, for space propulsion and for various applications in industry. The common features or requirements of our High Average-power Laser for Nuclear-fusion Application (HALNA) are large pulse energy with relatively low repetition of few tens Hz, good beam quality of order of diffraction limit and high efficiency more than 10%. We constructed HALNA 10 (10J X 10 Hz) and tested the performance to clarify the scalability to higher power system. We have obtained in a preliminary experiment a 8.5 J output energy at 0.5 Hz with beam quality of 2 times diffraction limited far-field pattern.

High Technology in the High School and Its Effect on Curriculum.

ERIC Educational Resources Information Center

Rizzolo, Ralph M.

The development and implementation of a high-tech laboratory in a small suburban high school in Pequannock Township, New Jersey, demonstrates that the high-tech future is both possible and valuable as it permeates the entire curriculum. In 1984, the vocational studies department shifted its emphasis to prepare students for college as well as for…

Another Innovation from High Tech High--Embedded Teacher Training

ERIC Educational Resources Information Center

Griswold, Janie; Riordan, Rob

2016-01-01

High Tech High School's teaching internship program blends on-the-job work with classroom theory. Interns spend two years working as full teachers as they take courses. The program serves three large purposes: Train new teachers and build capacity in the HTH organization; train teachers in and beyond HTH for success in a wide range of contexts;…

Parametric Investigation of a High-Lift Airfoil at High Reynolds Numbers

NASA Technical Reports Server (NTRS)

Lin, John C.; Dominik, Chet J.

1997-01-01

A new two-dimensional, three-element, advanced high-lift research airfoil has been tested in the NASA Langley Research Center s Low-Turbulence Pressure Tunnel at a chord Reynolds number up to 1.6 x 107. The components of this high-lift airfoil have been designed using a incompressible computational code (INS2D). The design was to provide high maximum-lift values while maintaining attached flow on the single-segment flap at landing conditions. The performance of the new NASA research airfoil is compared to a similar reference high-lift airfoil. On the new high-lift airfoil the effects of Reynolds number on slat and flap rigging have been studied experimentally, as well as the Mach number effects. The performance trend of the high-lift design is comparable to that predicted by INS2D over much of the angle-of-attack range. However, the code did not accurately predict the airfoil performance or the configuration-based trends near maximum lift where the compressibility effect could play a major role.

High-mix insulins

PubMed Central

Kalra, Sanjay; Farooqi, Mohammad Hamed; El-Houni, Ali E.

2015-01-01

Premix insulins are commonly used insulin preparations, which are available in varying ratios of different molecules. These drugs contain one short- or rapid-acting, and one intermediate- or long-acting insulin. High-mix insulins are mixtures of insulins that contain 50% or more than 50% of short-acting insulin. This review describes the clinical pharmacology of high-mix insulins, including data from randomized controlled trials. It suggests various ways, in which high-mix insulin can be used, including once daily, twice daily, thrice daily, hetero-mix, and reverse regimes. The authors provide a rational framework to help diabetes care professionals, identify indications for pragmatic high-mix use. PMID:26425485

High-fat, high-fructose, high-cholesterol feeding causes severe NASH and cecal microbiota dysbiosis in juvenile Ossabaw swine.

PubMed

Panasevich, M R; Meers, G M; Linden, M A; Booth, F W; Perfield, J W; Fritsche, K L; Wankhade, Umesh D; Chintapalli, Sree V; Shankar, K; Ibdah, J A; Rector, R S

2018-01-01

Pediatric obesity and nonalcoholic steatohepatitis (NASH) are on the rise in industrialized countries, yet our ability to mechanistically examine this relationship is limited by the lack of a suitable higher animal models. Here, we examined the effects of high-fat, high-fructose corn syrup, high-cholesterol Western-style diet (WD)-induced obesity on NASH and cecal microbiota dysbiosis in juvenile Ossabaw swine. Juvenile female Ossabaw swine (5 wk old) were fed WD (43.0% fat; 17.8% high-fructose corn syrup; 2% cholesterol) or low-fat diet (CON/lean; 10.5% fat) for 16 wk ( n = 6 each) or 36 wk ( n = 4 each). WD-fed pigs developed obesity, dyslipidemia, and systemic insulin resistance compared with CON pigs. In addition, obese WD-fed pigs developed severe NASH, with hepatic steatosis, hepatocyte ballooning, inflammatory cell infiltration, and fibrosis after 16 wk, with further exacerbation of histological inflammation and fibrosis after 36 wk of WD feeding. WD feeding also resulted in robust cecal microbiota changes including increased relative abundances of families and genera in Proteobacteria ( P < 0.05) (i.e., Enterobacteriaceae, Succinivibrionaceae, and Succinivibrio) and LPS-containing Desulfovibrionaceae and Desulfovibrio and a greater ( P < 0.05) predicted microbial metabolic function for LPS biosynthesis, LPS biosynthesis proteins, and peptidoglycan synthesis compared with CON-fed pigs. Overall, juvenile Ossabaw swine fed a high-fat, high-fructose, high-cholesterol diet develop obesity and severe microbiota dysbiosis with a proinflammatory signature and a NASH phenotype directly relevant to the pediatric/adolescent and young adult population.

Planning high security/high profile events.

PubMed

McCafferty, Mike

2013-01-01

The author who has lead in the planning and implementation of some of the most notorious trials and events, both in Canada and internationally, describes how such these experiences could be applied to focused high security planning in the health care industry.

High-temperature, high-pressure optical cell

NASA Technical Reports Server (NTRS)

Harris, R. P. (Inventor); Holland, L. R. (Inventor); Smith, R. E. (Inventor)

1986-01-01

The invention is an optical cell for containment of chemicals under conditions of high temperature and high pressure. The cell is formed of a vitreous silica tube, two optical windows comprising a vitreous silica rod inserted into the ends of a tube, and fused into position in the tube ends. Windows are spaced apart to form a cavity enclosed by the tube and the windows. A hole is drilled radially through the tube and into the cavity. Another vitreous silica tube is fused to the silica tube around the hole to form the stem, which is perpendicular to the long axis of the tube. The open end of the stem is used to load chemicals into the cavity. Then the stem may be sealed, and if desired, it may be shortened in order to reduce the volume of the cavity, which extends into the stem.

High-sensitivity, high-speed continuous imaging system

DOEpatents

Watson, Scott A; Bender, III, Howard A

2014-11-18

A continuous imaging system for recording low levels of light typically extending over small distances with high-frame rates and with a large number of frames is described. Photodiode pixels disposed in an array having a chosen geometry, each pixel having a dedicated amplifier, analog-to-digital convertor, and memory, provide parallel operation of the system. When combined with a plurality of scintillators responsive to a selected source of radiation, in a scintillator array, the light from each scintillator being directed to a single corresponding photodiode in close proximity or lens-coupled thereto, embodiments of the present imaging system may provide images of x-ray, gamma ray, proton, and neutron sources with high efficiency.

High-field magnets using high-critical-temperature superconducting thin films

DOEpatents

Mitlitsky, F.; Hoard, R.W.

1994-05-10

High-field magnets fabricated from high-critical-temperature superconducting ceramic (HTSC) thin films which can generate fields greater than 4 Tesla are disclosed. The high-field magnets are made of stackable disk-shaped substrates coated with HTSC thin films, and involves maximizing the critical current density, superconducting film thickness, number of superconducting layers per substrate, substrate diameter, and number of substrates while minimizing substrate thickness. The HTSC thin films are deposited on one or both sides of the substrates in a spiral configuration with variable line widths to increase the field. 4 figures.

High-field magnets using high-critical-temperature superconducting thin films

DOEpatents

Mitlitsky, Fred; Hoard, Ronald W.

1994-01-01

High-field magnets fabricated from high-critical-temperature superconducting ceramic (HTSC) thin films which can generate fields greater than 4 Tesla. The high-field magnets are made of stackable disk-shaped substrates coated with HTSC thin films, and involves maximizing the critical current density, superconducting film thickness, number of superconducting layers per substrate, substrate diameter, and number of substrates while minimizing substrate thickness. The HTSC thin films are deposited on one or both sides of the substrates in a spiral configuration with variable line widths to increase the field.

Fort Collins High School Wins 28th Colorado High School Science Bowl | News

Science.gov Websites

physics, math, biology, energy, chemistry, and earth and space sciences. Cherry Creek High School (Denver | NREL Fort Collins High School Wins 28th Colorado High School Science Bowl News Release: Fort Collins High School Wins 28th Colorado High School Science Bowl Team heading to Washington, D.C., to

Mining High-Dimensional Data

NASA Astrophysics Data System (ADS)

Wang, Wei; Yang, Jiong

With the rapid growth of computational biology and e-commerce applications, high-dimensional data becomes very common. Thus, mining high-dimensional data is an urgent problem of great practical importance. However, there are some unique challenges for mining data of high dimensions, including (1) the curse of dimensionality and more crucial (2) the meaningfulness of the similarity measure in the high dimension space. In this chapter, we present several state-of-art techniques for analyzing high-dimensional data, e.g., frequent pattern mining, clustering, and classification. We will discuss how these methods deal with the challenges of high dimensionality.

High Redshift GRBs

NASA Technical Reports Server (NTRS)

Gehrels, Neil; Cannizzo, John K.

2012-01-01

The Swift mission has opened a new, high redshift window on the universe. In this review we provide an overview of gamma-ray burst (GRB) science, describe the Swift mission, discuss high-z GRBs and tools for high-z studies, and look forward at future capabilities. A new mission concept - Lobster - is described that would monitor the X-ray sky at order of magnitude higher sensitivity than current missions.

High-power klystrons

NASA Astrophysics Data System (ADS)

Siambis, John G.; True, Richard B.; Symons, R. S.

1994-05-01

Novel emerging applications in advanced linear collider accelerators, ionospheric and atmospheric sensing and modification and a wide spectrum of industrial processing applications, have resulted in microwave tube requirements that call for further development of high power klystrons in the range from S-band to X-band. In the present paper we review recent progress in high power klystron development and discuss some of the issues and scaling laws for successful design. We also discuss recent progress in electron guns with potential grading electrodes for high voltage with short and long pulse operation via computer simulations obtained from the code DEMEOS, as well as preliminary experimental results. We present designs for high power beam collectors.

[Condition optimization for bio-oxidation of high-S and high-As gold concentrate].

PubMed

Yang, Caiyun; Dong, Bowen; Wang, Meijun; Ye, Zhiyong; Zheng, Tianling; Huang, Huaiguo

2015-12-04

To study the effects of temperature and lixivium return on the concentrate bio-oxidation and rate of gold cyanide leaching. The bioleaching of a high-sulphur (S) and high-arsenic (As) refractory gold concentrate was conducted, and we studied the effects of different temperature (40 ° and 45 °C) and lixivium return (0 and 600 mL) on the bio-oxidation efficiency. The bacterial community structure also was investigated by 16S rRNA gene clone library. The results showed that both the temperature and lixivium return significantly influenced the oxidation system. The temperature rising elevated the oxidation level, while the addition of lixivium depressed the oxidation. Dissimilarity and DCA (detrended correspondence analysis) indicated the effect of temperature on oxidation system was much greater than lixivium. The bacterial community was comprised by Acidithiocacillus caldu (71%) Leptospirillum ferriphilum (23%) and Sulfobacillus thermosulfidooxidans (6%) indicated by the clone library, and the OTU coverage based on 97% sequence similarity was as high as 93.67%. Temperature rising to 45 T would improve the oxidation efficiency while lixivium return would decrease it. This study is helpful to provide an important guiding value for the industry cost optimization of mesophile bacterial oxidation and reduction process.

Assessment of the hydrologic setting and mass transport within Saharan and Arabian Aquifers using GRACE, geochemical, geophysical and subsurface data

NASA Astrophysics Data System (ADS)

Sultan, M.; Sturchio, N. C.; Ahmed, M.; Saleh, S.; Mohamed, A.; Abuabdullah, M. M.; Emil, M. K.; Bettadpur, S. V.; Save, H.; Fathy, K.; Chouinard, K.

2016-12-01

A better understanding of the hydrologic setting, mass transport, origin, evolution, utilization, sustainability, and paleo-climatic recharge conditions of Saharan and Arabian aquifers was achieved by integrating observation from monthly (04/2002 to 03/2016) Gravity Recovery and Climate Experiment (GRACE)-derived Terrestrial Water Storage (TWS) from multiple GRACE solutions (mascons and spherical harmonic fields) with others from geochemical (solute chemistry), isotopic (O, H, Sr), geochronologic (Chlorine-36, Krypton-81), geophysical (aerogravity and aeromagnetic), and subsurface data. The investigated aquifers are: (1) Nubian Sandstone Aquifer System (NSAS; area: 2×106 km2) in northeast Africa and, (2) Mega Aquifer System (MAS; area: 1.1×106 km2) in Arabia. Our findings indicate the NSAS and MAS were largely recharged in previous wet climatic Pleistocene periods, as evidenced by the groundwater ages (up to 1 million years), yet they receive modest local recharge during interleaving dry periods in areas of relatively high (≥ 20 mm/yr) precipitation. In Sudan and Chad (southern NSAS), the average annual precipitation (AAP) is 95 mm/yr and the recharge is estimated at 3.2 x 109 m3/yr ( 7% of AAP); in the southwest parts of the MAS, the recharge at the foothills of the Red Sea mountains is 1.8 x 109 m3/yr (10% of AAP). Uplifts and/or shear zones orthogonal to groundwater flow impede the south to north flow in the NSAS as evidenced by the large differences in GRACE-derived TWS trends, groundwater ages, and isotopic compositions on either side of the east-west trending Uweinat-Aswan uplift. Similarly west to east groundwater flow in the MAS is impeded and impounded up-gradient from the N-S and/or NW-SE trending basement structures, reactivated during Red Sea opening. Shear zones subparallel to groundwater flow act as preferred flow pathways, as is the case with the NE-SW trending Pelusium shear zone which channels groundwater from the Kufra sub-basin (Libya

Evaluation of high temperature dielectric films for high voltage power electronic applications

NASA Technical Reports Server (NTRS)

Suthar, J. L.; Laghari, J. R.

1992-01-01

Three high temperature films, polyimide, Teflon perfluoroalkoxy and poly-P-xylene, were evaluated for possible use in high voltage power electronic applications, such as in high energy density capacitors, cables and microelectronic circuits. The dielectric properties, including permittivity and dielectric loss, were obtained in the frequency range of 50 Hz to 100 kHz at temperatures up to 200 C. The dielectric strengths at 60 Hz were determined as a function of temperature to 250 C. Confocal laser microscopy was performed to diagnose for voids and microimperfections within the film structure. The results obtained indicate that all films evaluated are capable of maintaining their high voltage properties, with minimal degradation, at temperatures up to 200 C. However, above 200 C, they lose some of their electrical properties. These films may therefore become viable candidates for high voltage power electronic applications at high temperatures.

Tracing Nile sediment sources by Sr and Nd isotope signatures (Uganda, Ethiopia, Sudan)

NASA Astrophysics Data System (ADS)

Padoan, Marta; Garzanti, Eduardo; Harlavan, Yehudit; Villa, Igor Maria

2011-06-01

Strontium and neodymium isotopes, measured on diverse mud and sand fractions of sediment in transit along all major Nile branches, identify detritus sourced from Precambrian basements, Mesozoic strata, and Tertiary volcanic rocks exposed along the shoulders of the East African rift and in Ethiopian highlands. Sr and Nd isotopic ratios reflect the weighted average of detrital components generated in different catchments, allowing us to discriminate provenance, calculate sediment budgets, and investigate grain-size and hydraulic-sorting effects. 87Sr/ 86Sr and 143Nd/ 144Nd range, respectively, from as high as 0.722 and as low as 0.5108 for sediment derived from Archean gneisses in northern Uganda, to 0.705 and 0.5127 for sediment derived from Neoproterozoic Ethiopian and Eritrean basements. 87Sr/ 86Sr and 143Nd/ 144Nd, ranging 0.705-0.709 and 0.5124-0.5130 for Blue Nile tributaries, are 0.704-0.705 and 0.5127-0.5128 for largely volcaniclastic sediments of River Tekeze-Atbara, and 0.705-0.706 and 0.5126-0.5127 for main Nile sediments upstream Lake Nasser. Model mantle derivation ages ( tDM), oldest in Uganda where sediment is principally derived from the Congo Craton (3.4-3.0 Ga for Victoria and Albert Nile), progressively decrease northward across the Saharan Metacraton, from 2.6 Ga (Bahr el Jebel in South Sudan), to 2.4-2.2 Ga (Bahr ez Zeraf across the Sudd), and finally 1.6-1.3 Ga (White Nile upstream Khartoum). Instead, tDM ages of Sobat mud increase from 0.9 to 1.5 Ga across the Machar marshes. TDM ages are younger for sediments shed by Ethiopian (1.2-0.7 Ga) and Eritrean basements (1.5-1.2 Ga), and youngest for sediments shed from Ethiopian flood basalts (0.3-0.2 Ga). Integrated geochemical, mineralogical, and settling-equivalence analyses suggest influence on the Nd isotopic signal by volcanic lithic grains and titanite rather than by LREE-rich monazite or allanite. Because contributions by ultradense minerals is subordinate, intrasample variability of Sr and

High voltage and high specific capacity dual intercalating electrode Li-ion batteries

NASA Technical Reports Server (NTRS)

Blanco, Mario (Inventor); West, William C. (Inventor)

2010-01-01

The present invention provides high capacity and high voltage Li-ion batteries that have a carbonaceous cathode and a nonaqueous electrolyte solution comprising LiF salt and an anion receptor that binds the fluoride ion. The batteries can comprise dual intercalating electrode Li ion batteries. Methods of the present invention use a cathode and electrode pair, wherein each of the electrodes reversibly intercalate ions provided by a LiF salt to make a high voltage and high specific capacity dual intercalating electrode Li-ion battery. The present methods and systems provide high-capacity batteries particularly useful in powering devices where minimizing battery mass is important.

High temperature refrigerator

DOEpatents

Steyert, Jr., William A.

1978-01-01

A high temperature magnetic refrigerator which uses a Stirling-like cycle in which rotating magnetic working material is heated in zero field and adiabatically magnetized, cooled in high field, then adiabatically demagnetized. During this cycle said working material is in heat exchange with a pumped fluid which absorbs heat from a low temperature heat source and deposits heat in a high temperature reservoir. The magnetic refrigeration cycle operates at an efficiency 70% of Carnot.

High-Frequency, High-Temperature Fretting Experiments

NASA Technical Reports Server (NTRS)

Matlik, J. F.; Farris, T. N.; Haake, F. K.; Swanson, G. R.; Duke, G. C.

2005-01-01

Fretting is a structural damage mechanism observed when two nominally clamped surfaces are subjected to an oscillatory loading. A critical location for fretting induced damage has been identified at the blade/disk and blade/damper interfaces of gas turbine engine turbomachinery and space propulsion components. The high-temperature, high-frequency loading environment seen by these components lead to severe stress gradients at the edge-of-contact. These contact stresses drive crack nucleation and propagation in fretting and are very sensitive to the geometry of the contacting bodies, the contact loads, materials, temperature, and contact surface tribology (friction). To diagnose the threat that small and relatively undetectable fretting cracks pose to damage tolerance and structural integrity of in-service components, the objective of this work is to develop a well-characterized experimental fretting rig capable of investigating fretting behavior of advanced aerospace alloys subjected to load and temperature conditions representative of such turbomachinery components.

A high-efficiency high-power-generation system for automobiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naidu, M.; Boules, N.; Henry, R.

This paper presents a new scheme for the efficient generation of high electric power demanded for future automobiles. The new system consists of a permanent-magnet (PM) alternator having high-energy MAGNEQUENCH (MQ) magnets and split winding and a novel electronic voltage-regulation scheme. A proof-of-concept system, capable of providing 100/250 A (idle/cruising) at 14 V, has been built and tested in the laboratory with encouraging results. This high output is provided at 15--20 percentage points higher efficiencies than conventional automotive alternators, which translates into considerable fuel economy savings. The system is 8 dB quieter and has a rotor inertia of only 2/3more » that of an equivalent production alternator, thus allowing for a belt drive without excessive slippage.« less

A high-efficiency, high power generation system for automobiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Naidu, M.; Boules, N.; Henry, R.

The paper presents a new scheme for the efficient generation of high electric power, demands for future automobiles. The new system, consists of a permanent magnet (PM) alternator having high energy MAGNEQUENCH (MQ) magnets and split winding; and a novel electronic voltage regulation scheme. A proof of concept system, capable of providing 100/250 A (idle/cruising) at 14 V, has been built and tested in the laboratory with encouraging results. This high output is provided at 15--20 percentage points higher efficiencies than conventional automotive alternators, which translates into considerable fuel economy savings. The system is 8 dB quieter and has amore » rotor inertia of only 2/3 that of an equivalent production alternator, thus allowing for a belt drive without excessive slippage.« less

High power klystrons for efficient reliable high power amplifiers

NASA Astrophysics Data System (ADS)

Levin, M.

1980-11-01

This report covers the design of reliable high efficiency, high power klystrons which may be used in both existing and proposed troposcatter radio systems. High Power (10 kW) klystron designs were generated in C-band (4.4 GHz to 5.0 GHz), S-band (2.5 GHz to 2.7 GHz), and L-band or UHF frequencies (755 MHz to 985 MHz). The tubes were designed for power supply compatibility and use with a vapor/liquid phase heat exchanger. Four (4) S-band tubes were developed in the course of this program along with two (2) matching focusing solenoids and two (2) heat exchangers. These tubes use five (5) tuners with counters which are attached to the focusing solenoids. A reliability mathematical model of the tube and heat exchanger system was also generated.

Zerodur polishing process for high surface quality and high efficiency

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tesar, A.; Fuchs, B.

1992-08-01

Zerodur is a glass-ceramic composite importance in applications where temperature instabilities influence optical and mechanical performance, such as in earthbound and spaceborne telescope mirror substrates. Polished Zerodur surfaces of high quality have been required for laser gyro mirrors. Polished surface quality of substrates affects performance of high reflection coatings. Thus, the interest in improving Zerodur polished surface quality has become more general. Beyond eliminating subsurface damage, high quality surfaces are produced by reducing the amount of hydrated material redeposited on the surface during polishing. With the proper control of polishing parameters, such surfaces exhibit roughnesses of

High-Fat, High-Sugar Diet-Induced Subendothelial Matrix Stiffening is Mitigated by Exercise.

PubMed

Kohn, Julie C; Azar, Julian; Seta, Francesca; Reinhart-King, Cynthia A

2018-03-01

Consumption of a high-fat, high-sugar diet and sedentary lifestyle are correlated with bulk arterial stiffening. While measurements of bulk arterial stiffening are used to assess cardiovascular health clinically, they cannot account for changes to the tissue occurring on the cellular scale. The compliance of the subendothelial matrix in the intima mediates vascular permeability, an initiating step in atherosclerosis. High-fat, high-sugar diet consumption and a sedentary lifestyle both cause micro-scale subendothelial matrix stiffening, but the impact of these factors in concert remains unknown. In this study, mice on a high-fat, high-sugar diet were treated with aerobic exercise or returned to a normal diet. We measured bulk arterial stiffness through pulse wave velocity and subendothelial matrix stiffness ex vivo through atomic force microscopy. Our data indicate that while diet reversal mitigates high-fat, high-sugar diet-induced macro- and micro-scale stiffening, exercise only significantly decreases micro-scale stiffness and not macro-scale stiffness, during the time-scale studied. These data underscore the need for both healthy diet and exercise to maintain vascular health. These data also indicate that exercise may serve as a key lifestyle modification to partially reverse the deleterious impacts of high-fat, high-sugar diet consumption, even while macro-scale stiffness indicators do not change.

A reactor for high-throughput high-pressure nuclear magnetic resonance spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Beach, N. J.; Knapp, S. M. M.; Landis, C. R., E-mail: landis@chem.wisc.edu

The design of a reactor for operando nuclear magnetic resonance (NMR) monitoring of high-pressure gas-liquid reactions is described. The Wisconsin High Pressure NMR Reactor (WiHP-NMRR) design comprises four modules: a sapphire NMR tube with titanium tube holder rated for pressures as high as 1000 psig (68 atm) and temperatures ranging from −90 to 90 °C, a gas circulation system that maintains equilibrium concentrations of dissolved gases during gas-consuming or gas-releasing reactions, a liquid injection apparatus that is capable of adding measured amounts of solutions to the reactor under high pressure conditions, and a rapid wash system that enables the reactor tomore » be cleaned without removal from the NMR instrument. The WiHP-NMRR is compatible with commercial 10 mm NMR probes. Reactions performed in the WiHP-NMRR yield high quality, information-rich, and multinuclear NMR data over the entire reaction time course with rapid experimental turnaround.« less

High resolution NMR imaging using a high field yokeless permanent magnet.

PubMed

Kose, Katsumi; Haishi, Tomoyuki

2011-01-01

We measured the homogeneity and stability of the magnetic field of a high field (about 1.04 tesla) yokeless permanent magnet with 40-mm gap for high resolution nuclear magnetic resonance (NMR) imaging. Homogeneity was evaluated using a 3-dimensional (3D) lattice phantom and 3D spin-echo imaging sequences. In the central sphere (20-mm diameter), peak-to-peak magnetic field inhomogeneity was about 60 ppm, and the root-mean-square was 8 ppm. We measured room temperature, magnet temperature, and NMR frequency of the magnet simultaneously every minute for about 68 hours with and without the thermal insulator of the magnet. A simple mathematical model described the magnet's thermal property. Based on magnet performance, we performed high resolution (up to [20 µm](2)) imaging with internal NMR lock sequences of several biological samples. Our results demonstrated the usefulness of the high field small yokeless permanent magnet for high resolution NMR imaging.

High performance polymer development

NASA Technical Reports Server (NTRS)

Hergenrother, Paul M.

1991-01-01

The term high performance as applied to polymers is generally associated with polymers that operate at high temperatures. High performance is used to describe polymers that perform at temperatures of 177 C or higher. In addition to temperature, other factors obviously influence the performance of polymers such as thermal cycling, stress level, and environmental effects. Some recent developments at NASA Langley in polyimides, poly(arylene ethers), and acetylenic terminated materials are discussed. The high performance/high temperature polymers discussed are representative of the type of work underway at NASA Langley Research Center. Further improvement in these materials as well as the development of new polymers will provide technology to help meet NASA future needs in high performance/high temperature applications. In addition, because of the combination of properties offered by many of these polymers, they should find use in many other applications.

Case Studies of Leading Edge Small Urban High Schools. Relevance Strategic Designs: 8. High Tech High School

ERIC Educational Resources Information Center

Shields, Regis Anne; Ireland, Nicole; City, Elizabeth; Derderian, Julie; Miles, Karen Hawley

2008-01-01

This report is one of nine detailed case studies of small urban high schools that served as the foundation for the Education Resource Strategies (ERS) report "Strategic Designs: Lessons from Leading Edge Small Urban High Schools." These nine schools were dubbed "Leading Edge Schools" because they stand apart from other high…

Laser-machined microcavities for simultaneous measurement of high-temperature and high-pressure.

PubMed

Ran, Zengling; Liu, Shan; Liu, Qin; Huang, Ya; Bao, Haihong; Wang, Yanjun; Luo, Shucheng; Yang, Huiqin; Rao, Yunjiang

2014-08-07

Laser-machined microcavities for simultaneous measurement of high-temperature and high-pressure are demonstrated. These two cascaded microcavities are an air cavity and a composite cavity including a section of fiber and an air cavity. They are both placed into a pressure chamber inside a furnace to perform simultaneous pressure and high-temperature tests. The thermal and pressure coefficients of the short air cavity are ~0.0779 nm/°C and ~1.14 nm/MPa, respectively. The thermal and pressure coefficients of the composite cavity are ~32.3 nm/°C and ~24.4 nm/MPa, respectively. The sensor could be used to separate temperature and pressure due to their different thermal and pressure coefficients. The excellent feature of such a sensor head is that it can withstand high temperatures of up to 400 °C and achieve precise measurement of high-pressure under high temperature conditions.

High temperature furnace

DOEpatents

Borkowski, Casimer J.

1976-08-03

A high temperature furnace for use above 2000.degree.C is provided that features fast initial heating and low power consumption at the operating temperature. The cathode is initially heated by joule heating followed by electron emission heating at the operating temperature. The cathode is designed for routine large temperature excursions without being subjected to high thermal stresses. A further characteristic of the device is the elimination of any ceramic components from the high temperature zone of the furnace.

Design of a high-power, high-brightness Nd:YAG solar laser.

PubMed

Liang, Dawei; Almeida, Joana; Garcia, Dário

2014-03-20

A simple high-power, high-brightness Nd:YAG solar laser pumping approach is presented in this paper. The incoming solar radiation is both collected and concentrated by four Fresnel lenses and redirected toward a Nd:YAG laser head by four plane-folding mirrors. A fused-silica secondary concentrator is used to compress the highly concentrated solar radiation to a laser rod. Optimum pumping conditions and laser resonator parameters are found through ZEMAX and LASCAD numerical analysis. Solar laser power of 96 W is numerically calculated, corresponding to the collection efficiency of 24  W/m². A record-high solar laser beam brightness figure of merit of 9.6 W is numerically achieved.

High-emulation mask recognition with high-resolution hyperspectral video capture system

NASA Astrophysics Data System (ADS)

Feng, Jiao; Fang, Xiaojing; Li, Shoufeng; Wang, Yongjin

2014-11-01

We present a method for distinguishing human face from high-emulation mask, which is increasingly used by criminals for activities such as stealing card numbers and passwords on ATM. Traditional facial recognition technique is difficult to detect such camouflaged criminals. In this paper, we use the high-resolution hyperspectral video capture system to detect high-emulation mask. A RGB camera is used for traditional facial recognition. A prism and a gray scale camera are used to capture spectral information of the observed face. Experiments show that mask made of silica gel has different spectral reflectance compared with the human skin. As multispectral image offers additional spectral information about physical characteristics, high-emulation mask can be easily recognized.

EPA AND ERDA HIGH-TEMPERATURE/HIGH-PRESSURE PARTICULATE CONTROL PROGRAMS

EPA Science Inventory

The report describes and compares current projects sponsored by EPA and the U.S. Energy Research and Development Administration (ERDA), relating to the control of particulate matter in fuel gas streams at high temperatures (1000 to 2000F) and high pressures (5 atm and greater). T...

High-Temperature Piezoelectric Sensing

PubMed Central

Jiang, Xiaoning; Kim, Kyungrim; Zhang, Shujun; Johnson, Joseph; Salazar, Giovanni

2014-01-01

Piezoelectric sensing is of increasing interest for high-temperature applications in aerospace, automotive, power plants and material processing due to its low cost, compact sensor size and simple signal conditioning, in comparison with other high-temperature sensing techniques. This paper presented an overview of high-temperature piezoelectric sensing techniques. Firstly, different types of high-temperature piezoelectric single crystals, electrode materials, and their pros and cons are discussed. Secondly, recent work on high-temperature piezoelectric sensors including accelerometer, surface acoustic wave sensor, ultrasound transducer, acoustic emission sensor, gas sensor, and pressure sensor for temperatures up to 1,250 °C were reviewed. Finally, discussions of existing challenges and future work for high-temperature piezoelectric sensing are presented. PMID:24361928

Highly directional thermal emitter

DOEpatents

Ribaudo, Troy; Shaner, Eric A; Davids, Paul; Peters, David W

2015-03-24

A highly directional thermal emitter device comprises a two-dimensional periodic array of heavily doped semiconductor structures on a surface of a substrate. The array provides a highly directional thermal emission at a peak wavelength between 3 and 15 microns when the array is heated. For example, highly doped silicon (HDSi) with a plasma frequency in the mid-wave infrared was used to fabricate nearly perfect absorbing two-dimensional gratings structures that function as highly directional thermal radiators. The absorption and emission characteristics of the HDSi devices possessed a high degree of angular dependence for infrared absorption in the 10-12 micron range, while maintaining high reflectivity of solar radiation (.about.64%) at large incidence angles.

High-field plasma acceleration in a high-ionization-potential gas

DOE PAGES

Corde, S.; Adli, E.; Allen, J. M.; ...

2016-06-17

Plasma accelerators driven by particle beams are a very promising future accelerator technology as they can sustain high accelerating fields over long distances with high energy efficiency. They rely on the excitation of a plasma wave in the wake of a drive beam. To generate the plasma, a neutral gas can be field-ionized by the head of the drive beam, in which case the distance of acceleration and energy gain can be strongly limited by head erosion. In our research, we overcome this limit and demonstrate that electrons in the tail of a drive beam can be accelerated by upmore » to 27 GeV in a high-ionization-potential gas (argon), boosting their initial 20.35 GeV energy by 130%. Particle-in-cell simulations show that the argon plasma is sustaining very high electric fields, of ~150 GV m -1, over ~20 cm. Lastly, the results open new possibilities for the design of particle beam drivers and plasma sources.« less

Development of a novel parallel-spool pilot operated high-pressure solenoid valve with high flow rate and high speed

NASA Astrophysics Data System (ADS)

Dong, Dai; Li, Xiaoning

2015-03-01

High-pressure solenoid valve with high flow rate and high speed is a key component in an underwater driving system. However, traditional single spool pilot operated valve cannot meet the demands of both high flow rate and high speed simultaneously. A new structure for a high pressure solenoid valve is needed to meet the demand of the underwater driving system. A novel parallel-spool pilot operated high-pressure solenoid valve is proposed to overcome the drawback of the current single spool design. Mathematical models of the opening process and flow rate of the valve are established. Opening response time of the valve is subdivided into 4 parts to analyze the properties of the opening response. Corresponding formulas to solve 4 parts of the response time are derived. Key factors that influence the opening response time are analyzed. According to the mathematical model of the valve, a simulation of the opening process is carried out by MATLAB. Parameters are chosen based on theoretical analysis to design the test prototype of the new type of valve. Opening response time of the designed valve is tested by verifying response of the current in the coil and displacement of the main valve spool. The experimental results are in agreement with the simulated results, therefore the validity of the theoretical analysis is verified. Experimental opening response time of the valve is 48.3 ms at working pressure of 10 MPa. The flow capacity test shows that the largest effective area is 126 mm2 and the largest air flow rate is 2320 L/s. According to the result of the load driving test, the valve can meet the demands of the driving system. The proposed valve with parallel spools provides a new method for the design of a high-pressure valve with fast response and large flow rate.

High-Tech Versus High-Touch: Components of Hospital Costs Vary Widely.

PubMed

Song, Paula H; Reiter, Kristin L; Yi Xu, Wendy

The recent release by the Centers for Medicare & Medicaid Services of hospital charge and payment data to the public has renewed a national dialogue on hospital costs and prices. However, to better understand the driving force of hospital pricing and to develop strategies for controlling expenditures, it is important to understand the underlying costs of providing hospital services. We use Medicare Provider and Analysis Review inpatient claims data and Medicare cost report data for fiscal years 2008 and 2012 to examine variations in the contribution of "high-tech" resources (i.e., technology/medical device-intensive resources) versus "high-touch" resources (i.e., labor-intensive resources) to the total costs of providing two common services, as well as assess how these costs have changed over time. We found that high-tech inputs accounted for a greater proportion of the total costs of surgical service, whereas medical service costs were primarily attributable to high-touch inputs. Although the total costs of services did not change significantly over time, the distribution of high-tech, high-touch, and other costs for each service varied considerably across hospitals. Understanding resource inputs and the varying contribution of these inputs by clinical condition is an important first step in developing effective cost control strategies.

High Impact = High Statistical Standards? Not Necessarily So

PubMed Central

Tressoldi, Patrizio E.; Giofré, David; Sella, Francesco; Cumming, Geoff

2013-01-01

What are the statistical practices of articles published in journals with a high impact factor? Are there differences compared with articles published in journals with a somewhat lower impact factor that have adopted editorial policies to reduce the impact of limitations of Null Hypothesis Significance Testing? To investigate these questions, the current study analyzed all articles related to psychological, neuropsychological and medical issues, published in 2011 in four journals with high impact factors: Science, Nature, The New England Journal of Medicine and The Lancet, and three journals with relatively lower impact factors: Neuropsychology, Journal of Experimental Psychology-Applied and the American Journal of Public Health. Results show that Null Hypothesis Significance Testing without any use of confidence intervals, effect size, prospective power and model estimation, is the prevalent statistical practice used in articles published in Nature, 89%, followed by articles published in Science, 42%. By contrast, in all other journals, both with high and lower impact factors, most articles report confidence intervals and/or effect size measures. We interpreted these differences as consequences of the editorial policies adopted by the journal editors, which are probably the most effective means to improve the statistical practices in journals with high or low impact factors. PMID:23418533

High impact  =  high statistical standards? Not necessarily so.

PubMed

Tressoldi, Patrizio E; Giofré, David; Sella, Francesco; Cumming, Geoff

2013-01-01

What are the statistical practices of articles published in journals with a high impact factor? Are there differences compared with articles published in journals with a somewhat lower impact factor that have adopted editorial policies to reduce the impact of limitations of Null Hypothesis Significance Testing? To investigate these questions, the current study analyzed all articles related to psychological, neuropsychological and medical issues, published in 2011 in four journals with high impact factors: Science, Nature, The New England Journal of Medicine and The Lancet, and three journals with relatively lower impact factors: Neuropsychology, Journal of Experimental Psychology-Applied and the American Journal of Public Health. Results show that Null Hypothesis Significance Testing without any use of confidence intervals, effect size, prospective power and model estimation, is the prevalent statistical practice used in articles published in Nature, 89%, followed by articles published in Science, 42%. By contrast, in all other journals, both with high and lower impact factors, most articles report confidence intervals and/or effect size measures. We interpreted these differences as consequences of the editorial policies adopted by the journal editors, which are probably the most effective means to improve the statistical practices in journals with high or low impact factors.

High-efficiency aperiodic two-dimensional high-contrast-grating hologram

NASA Astrophysics Data System (ADS)

Qiao, Pengfei; Zhu, Li; Chang-Hasnain, Connie J.

2016-03-01

High efficiency phase holograms are designed and implemented using aperiodic two-dimensional (2D) high-contrast gratings (HCGs). With our design algorithm and an in-house developed rigorous coupled-wave analysis (RCWA) package for periodic 2D HCGs, the structural parameters are obtained to achieve a full 360-degree phase-tuning range of the reflected or transmitted wave, while maintaining the power efficiency above 90%. For given far-field patterns or 3D objects to reconstruct, we can generate the near-field phase distribution through an iterative process. The aperiodic HCG phase plates we design for holograms are pixelated, and the local geometric parameters for each pixel to achieve desired phase alternation are extracted from our periodic HCG designs. Our aperiodic HCG holograms are simulated using the 3D finite-difference time-domain method. The simulation results confirm that the desired far-field patterns are successfully produced under illumination at the designed wavelength. The HCG holograms are implemented on the quartz wafers, using amorphous silicon as the high-index material. We propose HCG designs at both visible and infrared wavelengths, and our simulation confirms the reconstruction of 3D objects. The high-contrast gratings allow us to realize low-cost, compact, flat, and integrable holograms with sub-micrometer thicknesses.

Large-area high-power VCSEL pump arrays optimized for high-energy lasers

NASA Astrophysics Data System (ADS)

Wang, Chad; Geske, Jonathan; Garrett, Henry; Cardellino, Terri; Talantov, Fedor; Berdin, Glen; Millenheft, David; Renner, Daniel; Klemer, Daniel

2012-06-01

Practical, large-area, high-power diode pumps for one micron (Nd, Yb) as well as eye-safer wavelengths (Er, Tm, Ho) are critical to the success of any high energy diode pumped solid state laser. Diode efficiency, brightness, availability and cost will determine how realizable a fielded high energy diode pumped solid state laser will be. 2-D Vertical-Cavity Surface-Emitting Laser (VCSEL) arrays are uniquely positioned to meet these requirements because of their unique properties, such as low divergence circular output beams, reduced wavelength drift with temperature, scalability to large 2-D arrays through low-cost and high-volume semiconductor photolithographic processes, high reliability, no catastrophic optical damage failure, and radiation and vacuum operation tolerance. Data will be presented on the status of FLIR-EOC's VCSEL pump arrays. Analysis of the key aspects of electrical, thermal and mechanical design that are critical to the design of a VCSEL pump array to achieve high power efficient array performance will be presented.

High-Altitude Illness

MedlinePlus

... after you travel. Make sure you pack enough water while you are active. Avoid or limit the amount of alcohol you consume. High-altitude illness treatment It is important to treat high-altitude illness ...

High Blood Cholesterol

MedlinePlus

... high blood cholesterol: Chronic kidney disease Diabetes HIV Hypothyroidism Overweight and obesity Polycystic ovary syndrome Inflammatory diseases ... your thyroid hormone levels can help rule out hypothyroidism as a cause of high blood levels of ...

High-Definition Medicine.

PubMed

Torkamani, Ali; Andersen, Kristian G; Steinhubl, Steven R; Topol, Eric J

2017-08-24

The foundation for a new era of data-driven medicine has been set by recent technological advances that enable the assessment and management of human health at an unprecedented level of resolution-what we refer to as high-definition medicine. Our ability to assess human health in high definition is enabled, in part, by advances in DNA sequencing, physiological and environmental monitoring, advanced imaging, and behavioral tracking. Our ability to understand and act upon these observations at equally high precision is driven by advances in genome editing, cellular reprogramming, tissue engineering, and information technologies, especially artificial intelligence. In this review, we will examine the core disciplines that enable high-definition medicine and project how these technologies will alter the future of medicine. Copyright © 2017 Elsevier Inc. All rights reserved.

High resolution and high sensitivity methods for oligosaccharide mapping and characterization by normal phase high performance liquid chromatography following derivatization with highly fluorescent anthranilic acid.

PubMed

Anumula, K R; Dhume, S T

1998-07-01

Facile labeling of oligosaccharides (acidic and neutral) in a nonselective manner was achieved with highly fluorescent anthranilic acid (AA, 2-aminobenzoic acid) (more than twice the intensity of 2-aminobenzamide, AB) for specific detection at very high sensitivity. Quantitative labeling in acetate-borate buffered methanol (approximately pH 5.0) at 80 degreesC for 60 min resulted in negligible or no desialylation of the oligosaccharides. A high resolution high performance liquid chromatographic method was developed for quantitative oligosaccharide mapping on a polymeric-NH2bonded (Astec) column operating under normal phase and anion exchange (NP-HPAEC) conditions. For isolation of oligosaccharides from the map by simple evaporation, the chromatographic conditions developed use volatile acetic acid-triethylamine buffer (approximately pH 4.0) systems. The mapping and characterization technology was developed using well characterized standard glycoproteins. The fluorescent oligosaccharide maps were similar to the maps obtained by the high pH anion-exchange chromatography with pulsed amperometric detection (HPAEC-PAD), except that the fluorescent maps contained more defined peaks. In the map, the oligosaccharides separated into groups based on charge, size, linkage, and overall structure in a manner similar to HPAEC-PAD with contribution of -COOH function from the label, anthranilic acid. However, selectivity of the column for sialic acid linkages was different. A second dimension normal phase HPLC (NP-HPLC) method was developed on an amide column (TSK Gel amide-80) for separation of the AA labeled neutral complex type and isomeric structures of high mannose type oligosaccharides. The oligosaccharides labeled with AA are compatible with biochemical and biophysical techniques, and use of matrix assisted laser desorption mass spectrometry for rapid determination of oligosaccharide mass map of glycoproteins is demonstrated. High resolution of NP-HPAEC and NP-HPLC methods

High-performance liquid chromatography of oligoguanylates at high pH

NASA Technical Reports Server (NTRS)

Stribling, R.; Deamer, D. (Principal Investigator)

1991-01-01

Because of the stable self-structures formed by oligomers of guanosine, standard high-performance liquid chromatography techniques for oligonucleotide fractionation are not applicable. Previously, oligoguanylate separations have been carried out at pH 12 using RPC-5 as the packing material. While RPC-5 provides excellent separations, there are several limitations, including the lack of a commercially available source. This report describes a new anion-exchange high-performance liquid chromatography method using HEMA-IEC BIO Q, which successfully separates different forms of the guanosine monomer as well as longer oligoguanylates. The reproducibility and stability at high pH suggests a versatile role for this material.

High Power Klystrons for Efficient Reliable High Power Amplifiers.

DTIC Science & Technology

1980-11-01

techniques to obtain high overall efficiency. One is second harmonic space charge bunching. This is a process whereby the fundamental and second harmonic...components of the space charge waves in the electron beam of a microwave tube are combined to produce more highly concentrated electron bunches raising the...the drift lengths to enhance the 2nd harmonic component in the space charge waves. The latter method was utilized in the VKC-7790. Computer

Generalized Nonlinear Chirp Scaling Algorithm for High-Resolution Highly Squint SAR Imaging

PubMed Central

He, Zhihua; He, Feng; Dong, Zhen; Wu, Manqing

2017-01-01

This paper presents a modified approach for high-resolution, highly squint synthetic aperture radar (SAR) data processing. Several nonlinear chirp scaling (NLCS) algorithms have been proposed to solve the azimuth variance of the frequency modulation rates that are caused by the linear range walk correction (LRWC). However, the azimuth depth of focusing (ADOF) is not handled well by these algorithms. The generalized nonlinear chirp scaling (GNLCS) algorithm that is proposed in this paper uses the method of series reverse (MSR) to improve the ADOF and focusing precision. It also introduces a high order processing kernel to avoid the range block processing. Simulation results show that the GNLCS algorithm can enlarge the ADOF and focusing precision for high-resolution highly squint SAR data. PMID:29112151

Generalized Nonlinear Chirp Scaling Algorithm for High-Resolution Highly Squint SAR Imaging.

PubMed

Yi, Tianzhu; He, Zhihua; He, Feng; Dong, Zhen; Wu, Manqing

2017-11-07

This paper presents a modified approach for high-resolution, highly squint synthetic aperture radar (SAR) data processing. Several nonlinear chirp scaling (NLCS) algorithms have been proposed to solve the azimuth variance of the frequency modulation rates that are caused by the linear range walk correction (LRWC). However, the azimuth depth of focusing (ADOF) is not handled well by these algorithms. The generalized nonlinear chirp scaling (GNLCS) algorithm that is proposed in this paper uses the method of series reverse (MSR) to improve the ADOF and focusing precision. It also introduces a high order processing kernel to avoid the range block processing. Simulation results show that the GNLCS algorithm can enlarge the ADOF and focusing precision for high-resolution highly squint SAR data.

High performance, high durability non-precious metal fuel cell catalysts

DOEpatents

Wood, Thomas E.; Atanasoski, Radoslav; Schmoeckel, Alison K.

2016-03-15

This invention relates to non-precious metal fuel cell cathode catalysts, fuel cells that contain these catalysts, and methods of making the same. The fuel cell cathode catalysts are highly nitrogenated carbon materials that can contain a transition metal. The highly nitrogenated carbon materials can be supported on a nanoparticle substrate.

High Resolution, High Frame Rate Video Technology

NASA Technical Reports Server (NTRS)

1990-01-01

Papers and working group summaries presented at the High Resolution, High Frame Rate Video (HHV) Workshop are compiled. HHV system is intended for future use on the Space Shuttle and Space Station Freedom. The Workshop was held for the dual purpose of: (1) allowing potential scientific users to assess the utility of the proposed system for monitoring microgravity science experiments; and (2) letting technical experts from industry recommend improvements to the proposed near-term HHV system. The following topics are covered: (1) State of the art in the video system performance; (2) Development plan for the HHV system; (3) Advanced technology for image gathering, coding, and processing; (4) Data compression applied to HHV; (5) Data transmission networks; and (6) Results of the users' requirements survey conducted by NASA.

High-efficiency high-reliability optical components for a large, high-average-power visible laser system

NASA Astrophysics Data System (ADS)

Taylor, John R.; Stolz, Christopher J.

1993-08-01

Laser system performance and reliability depends on the related performance and reliability of the optical components which define the cavity and transport subsystems. High-average-power and long transport lengths impose specific requirements on component performance. The complexity of the manufacturing process for optical components requires a high degree of process control and verification. Qualification has proven effective in ensuring confidence in the procurement process for these optical components. Issues related to component reliability have been studied and provide useful information to better understand the long term performance and reliability of the laser system.

High-efficiency high-reliability optical components for a large, high-average-power visible laser system

NASA Astrophysics Data System (ADS)

Taylor, J. R.; Stolz, C. J.

1992-12-01

Laser system performance and reliability depends on the related performance and reliability of the optical components which define the cavity and transport subsystems. High-average-power and long transport lengths impose specific requirements on component performance. The complexity of the manufacturing process for optical components requires a high degree of process control and verification. Qualification has proven effective in ensuring confidence in the procurement process for these optical components. Issues related to component reliability have been studied and provide useful information to better understand the long term performance and reliability of the laser system.

Integration of high capacity materials into interdigitated mesostructured electrodes for high energy and high power density primary microbatteries

NASA Astrophysics Data System (ADS)

Pikul, James H.; Liu, Jinyun; Braun, Paul V.; King, William P.

2016-05-01

Microbatteries are increasingly important for powering electronic systems, however, the volumetric energy density of microbatteries lags behind that of conventional format batteries. This paper reports a primary microbattery with energy density 45.5 μWh cm-2 μm-1 and peak power 5300 μW cm-2 μm-1, enabled by the integration of large volume fractions of high capacity anode and cathode chemistry into porous micro-architectures. The interdigitated battery electrodes consist of a lithium metal anode and a mesoporous manganese oxide cathode. The key enabler of the high energy and power density is the integration of the high capacity manganese oxide conversion chemistry into a mesostructured high power interdigitated bicontinuous cathode architecture and an electrodeposited dense lithium metal anode. The resultant energy density is greater than previously reported three-dimensional microbatteries and is comparable to commercial conventional format lithium-based batteries.

Oasis: A high-level/high-performance open source Navier-Stokes solver

NASA Astrophysics Data System (ADS)

Mortensen, Mikael; Valen-Sendstad, Kristian

2015-03-01

Oasis is a high-level/high-performance finite element Navier-Stokes solver written from scratch in Python using building blocks from the FEniCS project (fenicsproject.org). The solver is unstructured and targets large-scale applications in complex geometries on massively parallel clusters. Oasis utilizes MPI and interfaces, through FEniCS, to the linear algebra backend PETSc. Oasis advocates a high-level, programmable user interface through the creation of highly flexible Python modules for new problems. Through the high-level Python interface the user is placed in complete control of every aspect of the solver. A version of the solver, that is using piecewise linear elements for both velocity and pressure, is shown to reproduce very well the classical, spectral, turbulent channel simulations of Moser et al. (1999). The computational speed is strongly dominated by the iterative solvers provided by the linear algebra backend, which is arguably the best performance any similar implicit solver using PETSc may hope for. Higher order accuracy is also demonstrated and new solvers may be easily added within the same framework.

High-chroma visual cryptography using interference color of high-order retarder films

NASA Astrophysics Data System (ADS)

Sugawara, Shiori; Harada, Kenji; Sakai, Daisuke

2015-08-01

Visual cryptography can be used as a method of sharing a secret image through several encrypted images. Conventional visual cryptography can display only monochrome images. We have developed a high-chroma color visual encryption technique using the interference color of high-order retarder films. The encrypted films are composed of a polarizing film and retarder films. The retarder films exhibit interference color when they are sandwiched between two polarizing films. We propose a stacking technique for displaying high-chroma interference color images. A prototype visual cryptography device using high-chroma interference color is developed.

High Performance Regimes in Alcator C-Mod at High Magnetic Field

NASA Astrophysics Data System (ADS)

Marmar, E. S.; Alcator C-Mod Team

2017-10-01

Alcator is the only divertor tokamak in the world capable of operating at magnetic fields up to 8 T, equaling and exceeding that planned for ITER. Using RF and microwave tools for auxiliary heating and current drive, C-Mod accesses high pressure, high density, reactor-relevant regimes with no external torque and equilibrated electrons and ions, with exclusive use of high-Z metal plasma-facing components. The 2016 experimental campaign focused on naturally ELM-suppressed, enhanced energy confinement regimes (including I-mode and EDA H-mode, and approaches to super-H-mode), with emphasis on operation at the highest fields (52 atm.) was achieved. Taken together, combined with previous results from C-Mod and the world tokamak database, these results form a strong foundation for the high field, compact approach to achieving fusion energy production. New advances in high temperature, high field superconductors open the possibilities for practical development of this path for commercial fusion. Supported by USDOE.

Proposed Ultra-High Sensitivity High-Frequency Gravitational Wave Detector

NASA Astrophysics Data System (ADS)

Baker, Robert M. L.; Stephenson, Gary V.; Li, Fangyu

2008-01-01

The paper discusses the proposed improvement of a High-Frequency Relic Gravitational Wave (HFRGW) detector designed by Li, Baker, Fang, Stephenson and Chen in order to greatly improve its sensitivity. The improved detector is inspired by the Laser Interferometer Gravitational Observatory or LIGO, but is sensitive to the high-frequency end of the gravitational-wave spectrum. As described in prior papers it utilizes the Gertsenshtein effect, which introduces the conversion of gravitational waves to electromagnetic (EM) waves in the presence of a static magnetic field. Such a conversion, if it leads to photons moving in a direction perpendicular to the plane of the EM waves and the magnetic field, will allow for ultra-high sensitivity HFRGW detection. The use of sensitive microwave, single photon detectors such as a circuit QED and/or the Rydberg Atom Cavity Detector, or off-the-shelf detectors, could lead to such detection. When the EM-detection photons are focused at the microwave detectors by fractal-membrane reflectors sensitivity is also improved. Noise sources external to the HFRGW detector will be eliminated by placing a tight mosaic of superconducting tiles (e.g., YBCO) and/or fractal membranes on the interior surface of the detector's cryogenic containment vessel in order to provide a perfect Faraday cage. Internal thermal noise will be eliminated by means of a microwave absorbing (or reflecting) interior enclosure shaped to conform to a high-intensity continuous microwave Gaussian beam (GB), will reduce any background photon flux (BPF) noise radiated normal to the GB's axis. Such BPF will be further attenuated by a series of microwave absorbing baffles forming tunnels to the sensitive microwave detectors on each side of the GB and at right angles to the static magnetic field. A HFGW detector of bandwidth of 1 KHz to 10 KHz or less in the GHz band has been selected. It is concluded that the utilization of the new ultra-high-sensitivity microwave detectors

High-Tensile Strength Tape Versus High-Tensile Strength Suture: A Biomechanical Study.

PubMed

Gnandt, Ryan J; Smith, Jennifer L; Nguyen-Ta, Kim; McDonald, Lucas; LeClere, Lance E

2016-02-01

To determine which suture design, high-tensile strength tape or high-tensile strength suture, performed better at securing human tissue across 4 selected suture techniques commonly used in tendinous repair, by comparing the total load at failure measured during a fixed-rate longitudinal single load to failure using a biomechanical testing machine. Matched sets of tendon specimens with bony attachments were dissected from 15 human cadaveric lower extremities in a manner allowing for direct comparison testing. With the use of selected techniques (simple Mason-Allen in the patellar tendon specimens, whip stitch in the quadriceps tendon specimens, and Krackow stitch in the Achilles tendon specimens), 1 sample of each set was sutured with a 2-mm braided, nonabsorbable, high-tensile strength tape and the other with a No. 2 braided, nonabsorbable, high-tensile strength suture. A total of 120 specimens were tested. Each model was loaded to failure at a fixed longitudinal traction rate of 100 mm/min. The maximum load and failure method were recorded. In the whip stitch and the Krackow-stitch models, the high-tensile strength tape had a significantly greater mean load at failure with a difference of 181 N (P = .001) and 94 N (P = .015) respectively. No significant difference was found in the Mason-Allen and simple stitch models. Pull-through remained the most common method of failure at an overall rate of 56.7% (suture = 55%; tape = 58.3%). In biomechanical testing during a single load to failure, high-tensile strength tape performs more favorably than high-tensile strength suture, with a greater mean load to failure, in both the whip- and Krackow-stitch models. Although suture pull-through remains the most common method of failure, high-tensile strength tape requires a significantly greater load to pull-through in a whip-stitch and Krakow-stitch model. The biomechanical data obtained in the current study indicates that high-tensile strength tape may provide better repair

DistributedFBA.jl: High-level, high-performance flux balance analysis in Julia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Heirendt, Laurent; Thiele, Ines; Fleming, Ronan M. T.

Flux balance analysis and its variants are widely used methods for predicting steady-state reaction rates in biochemical reaction networks. The exploration of high dimensional networks with such methods is currently hampered by software performance limitations. DistributedFBA.jl is a high-level, high-performance, open-source implementation of flux balance analysis in Julia. It is tailored to solve multiple flux balance analyses on a subset or all the reactions of large and huge-scale networks, on any number of threads or nodes. DistributedFBA.jl is a high-level, high-performance, open-source implementation of flux balance analysis in Julia. It is tailored to solve multiple flux balance analyses on amore » subset or all the reactions of large and huge-scale networks, on any number of threads or nodes.« less

DistributedFBA.jl: High-level, high-performance flux balance analysis in Julia

DOE PAGES

Heirendt, Laurent; Thiele, Ines; Fleming, Ronan M. T.

2017-01-16

Flux balance analysis and its variants are widely used methods for predicting steady-state reaction rates in biochemical reaction networks. The exploration of high dimensional networks with such methods is currently hampered by software performance limitations. DistributedFBA.jl is a high-level, high-performance, open-source implementation of flux balance analysis in Julia. It is tailored to solve multiple flux balance analyses on a subset or all the reactions of large and huge-scale networks, on any number of threads or nodes. DistributedFBA.jl is a high-level, high-performance, open-source implementation of flux balance analysis in Julia. It is tailored to solve multiple flux balance analyses on amore » subset or all the reactions of large and huge-scale networks, on any number of threads or nodes.« less

Combining high biodiversity with high yields in tropical agroforests.

PubMed

Clough, Yann; Barkmann, Jan; Juhrbandt, Jana; Kessler, Michael; Wanger, Thomas Cherico; Anshary, Alam; Buchori, Damayanti; Cicuzza, Daniele; Darras, Kevin; Putra, Dadang Dwi; Erasmi, Stefan; Pitopang, Ramadhanil; Schmidt, Carsten; Schulze, Christian H; Seidel, Dominik; Steffan-Dewenter, Ingolf; Stenchly, Kathrin; Vidal, Stefan; Weist, Maria; Wielgoss, Arno Christian; Tscharntke, Teja

2011-05-17

Local and landscape-scale agricultural intensification is a major driver of global biodiversity loss. Controversially discussed solutions include wildlife-friendly farming or combining high-intensity farming with land-sparing for nature. Here, we integrate biodiversity and crop productivity data for smallholder cacao in Indonesia to exemplify for tropical agroforests that there is little relationship between yield and biodiversity under current management, opening substantial opportunities for wildlife-friendly management. Species richness of trees, fungi, invertebrates, and vertebrates did not decrease with yield. Moderate shade, adequate labor, and input level can be combined with a complex habitat structure to provide high biodiversity as well as high yields. Although livelihood impacts are held up as a major obstacle for wildlife-friendly farming in the tropics, our results suggest that in some situations, agroforests can be designed to optimize both biodiversity and crop production benefits without adding pressure to convert natural habitat to farmland.

New high-strength, high-conductivity Cu-Ag alloy sheets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakai, Y.; Inoue, K.; Maeda, H.

1995-04-01

A sheet-conductor fabrication method has been developed for Cu-Ag alloys containing 6--24 wt% Ag in which high-strength and high-conductivity are obtained by coldworking combined with intermediate heat treatments. The intermediate heat treatments were repeated three times at 400--450 C for 1--2 h at appropriate stages of cold-rolling. The optimized Cu-24 wt% Ag alloy sheet with a 96% reduction ratio shows an ultimate tensile strength of 1,050 MPa and an electrical conductivity of 75% IACS at room temperature. Anisotropy in the strength with respect to the rolling direction is less than 10%, and no anisotropy in the electrical conductivity occurs. Themore » authors demonstrated the ability to manufacture the Cu-Ag sheets for Bitter magnet on a commercial basis. The sheets fabricated by this method are promising as conductors for high-field Bitter magnet coils.« less

Note: High precision measurements using high frequency gigahertz signals

NASA Astrophysics Data System (ADS)

Jin, Aohan; Fu, Siyuan; Sakurai, Atsunori; Liu, Liang; Edman, Fredrik; Pullerits, Tõnu; Öwall, Viktor; Karki, Khadga Jung

2014-12-01

Generalized lock-in amplifiers use digital cavities with Q-factors as high as 5 × 108 to measure signals with very high precision. In this Note, we show that generalized lock-in amplifiers can be used to analyze microwave (giga-hertz) signals with a precision of few tens of hertz. We propose that the physical changes in the medium of propagation can be measured precisely by the ultra-high precision measurement of the signal. We provide evidence to our proposition by verifying the Newton's law of cooling by measuring the effect of change in temperature on the phase and amplitude of the signals propagating through two calibrated cables. The technique could be used to precisely measure different physical properties of the propagation medium, for example, the change in length, resistance, etc. Real time implementation of the technique can open up new methodologies of in situ virtual metrology in material design.

High performance, high density hydrocarbon fuels

NASA Technical Reports Server (NTRS)

Frankenfeld, J. W.; Hastings, T. W.; Lieberman, M.; Taylor, W. F.

1978-01-01

The fuels were selected from 77 original candidates on the basis of estimated merit index and cost effectiveness. The ten candidates consisted of 3 pure compounds, 4 chemical plant streams and 3 refinery streams. Critical physical and chemical properties of the candidate fuels were measured including heat of combustion, density, and viscosity as a function of temperature, freezing points, vapor pressure, boiling point, thermal stability. The best all around candidate was found to be a chemical plant olefin stream rich in dicyclopentadiene. This material has a high merit index and is available at low cost. Possible problem areas were identified as low temperature flow properties and thermal stability. An economic analysis was carried out to determine the production costs of top candidates. The chemical plant and refinery streams were all less than 44 cent/kg while the pure compounds were greater than 44 cent/kg. A literature survey was conducted on the state of the art of advanced hydrocarbon fuel technology as applied to high energy propellents. Several areas for additional research were identified.

High-performance axicon lenses based on high-contrast, multilayer gratings

NASA Astrophysics Data System (ADS)

Doshay, Sage; Sell, David; Yang, Jianji; Yang, Rui; Fan, Jonathan A.

2018-01-01

Axicon lenses are versatile optical elements that can convert Gaussian beams to Bessel-like beams. In this letter, we demonstrate that axicons operating with high efficiencies and at large angles can be produced using high-contrast, multilayer gratings made from silicon. Efficient beam deflection of incident monochromatic light is enabled by higher-order optical modes in the silicon structure. Compared to diffractive devices made from low-contrast materials such as silicon dioxide, our multilayer devices have a relatively low spatial profile, reducing shadowing effects and enabling high efficiencies at large deflection angles. In addition, the feature sizes of these structures are relatively large, making the fabrication of near-infrared devices accessible with conventional optical lithography. Experimental lenses with deflection angles as large as 40° display field profiles that agree well with theory. Our concept can be used to design optical elements that produce higher-order Bessel-like beams, and the combination of high-contrast materials with multilayer architectures will more generally enable new classes of diffractive photonic structures.

The CMS High Granularity Calorimeter for the High Luminosity LHC

NASA Astrophysics Data System (ADS)

Sauvan, J.-B.

2018-02-01

The High Luminosity LHC (HL-LHC) will integrate 10 times more luminosity than the LHC, posing significant challenges for radiation tolerance and event pileup on detectors, especially for forward calorimetry, and hallmarks the issue for future colliders. As part of its HL-LHC upgrade program, the CMS collaboration is designing a High Granularity Calorimeter to replace the existing endcap calorimeters. It features unprecedented transverse and longitudinal segmentation for both electromagnetic (ECAL) and hadronic (HCAL) compartments. This will facilitate particle-flow calorimetry, where the fine structure of showers can be measured and used to enhance pileup rejection and particle identification, whilst still achieving good energy resolution. The ECAL and a large fraction of HCAL will be based on hexagonal silicon sensors of 0.5-1 cm2 cell size, with the remainder of the HCAL based on highly-segmented scintillators with silicon photomultiplier (SiPM) readout. The intrinsic high-precision timing capabilities of the silicon sensors will add an extra dimension to event reconstruction, especially in terms of pileup rejection.

Characteristics of low-and high-fat beef patties: effect of high hydrostatic pressure.

PubMed

Carballo, J; Fernandez, P; Carrascosa, A V; Solas, M T; Colmenero, F J

1997-01-01

The purpose of this study was to analyze the consequences of applying high pressures (100 and 300 MPa for 5 or 20 min) on characteristics such as water- and fat-binding properties, texture, color, microstructure, and microbiology of low-fat (9.2%) and high-fat (20.3%) beef patties. In nonpressurized patties, the low-fat product exhibited significantly poorer (P < 0.05) binding properties and higher (P < 0.05) Kramer shear force and Kramer energy than did high-fat patties. Although high pressure did not clearly influence the binding properties of low- and high-fat beef patties, it did produce a rise in the Kramer shear force and energy which were more pronounced at 300 MPa. High pressures altered patty color, the extent of alteration depending on fat content, pressure, and pressurizing time. Pressurizing high- and low-fat beef patties at 300 MPa not only produced a lethal effect (P < 0.05) on microorganisms, but caused sublethal damage as well.

Athletes at High Altitude

PubMed Central

Khodaee, Morteza; Grothe, Heather L.; Seyfert, Jonathan H.; VanBaak, Karin

2016-01-01

Context: Athletes at different skill levels perform strenuous physical activity at high altitude for a variety of reasons. Multiple team and endurance events are held at high altitude and may place athletes at increased risk for developing acute high altitude illness (AHAI). Training at high altitude has been a routine part of preparation for some of the high level athletes for a long time. There is a general belief that altitude training improves athletic performance for competitive and recreational athletes. Evidence Acquisition: A review of relevant publications between 1980 and 2015 was completed using PubMed and Google Scholar. Study Design: Clinical review. Level of Evidence: Level 3. Results: AHAI is a relatively uncommon and potentially serious condition among travelers to altitudes above 2500 m. The broad term AHAI includes several syndromes such as acute mountain sickness (AMS), high altitude pulmonary edema (HAPE), and high altitude cerebral edema (HACE). Athletes may be at higher risk for developing AHAI due to faster ascent and more vigorous exertion compared with nonathletes. Evidence regarding the effects of altitude training on athletic performance is weak. The natural live high, train low altitude training strategy may provide the best protocol for enhancing endurance performance in elite and subelite athletes. High altitude sports are generally safe for recreational athletes, but they should be aware of their individual risks. Conclusion: Individualized and appropriate acclimatization is an essential component of injury and illness prevention. PMID:26863894

Biomphalaria alexandrina in Egypt: past, present and future.

PubMed

Abou-El-Naga, Iman F

2013-09-01

The African species of Biomphalaria appeared as a result of the relatively recent west-to-east trans-Atlantic dispersal of the Biomphalaria glabrata-like taxon. In Egypt, Biomphalaria alexandrina is the intermediate host for Schistosoma mansoni. Biomphalaria alexandrina originated in the area between Alexandria and Rosetta and has historically been confined to the Nile Delta. Schistosoma mansoni reached Egypt via infected slaves and baboons from the Land of Punt through migrations that occurred as early as the Vth Dynasty. The suggestion of the presence of Schistosoma mansoni infection in Lower Egypt during Pharaonic times is discussed despite the fact that that there is no evidence of such infection in Egyptian mummies. It is only recently that Biomphalaria alexandrina colonized the Egyptian Nile from the Delta to Lake Nasser. This change was likely due to the construction of huge water projects, the development of new water resources essential for land reclamation projects and the movement of refugees from the Suez Canal zone to the Delta and vice versa. The situation with respect to Biomphalaria in Egypt has become complicated in recent years by the detection of Biomphalaria glabrata and a hybrid between both species; however, follow-up studies have demonstrated the disappearance of such species within Egypt. The National Schistosoma Control Program has made great strides with respect to the eradication of schistosoma; however, there has unfortunately been a reemergence of Schistosoma mansoni resistant to praziquantel. There are numerous factors that may influence the prevalence of snails in Egypt, including the construction of water projects, the increase in reclaimed areas, global climate change and pollution. Thus, continued field studies in addition to the cooperation of several scientists are needed to obtain an accurate representation of the status of this species. In addition, the determination of the genome sequence for Biomphalaria alexandrina and the

Introduction to the Proceedings of the 9th ISDH

NASA Astrophysics Data System (ADS)

Bove, V. Michael, Jr.; Riskin, Seth

2013-02-01

The Proceedings As co-chairs of the 9th International Symposium on Display Holography, we welcome readers of this collection of papers and posters presented at the event. We hope that both attendees of the event and others pursuing the art, science, and business of holography and 3D imaging will find the authors' contributions of lasting interest and importance. The Event Since its creation at Lake Forest College in 1982 by Professor Tung H Jeong, ISDH has followed a model that differentiates it from other scientific conferences. The 9th ISDH continued this history, fully occupying a floor of the MIT Media Lab for five days. The single-track conference opened with reports on the state of holography in the various nations represented by the attendees, followed by a series of presentations on Education and Holography. One and one-half days of papers on Art and Holography followed, then sessions on Techniques and Materials, Digital Techniques, and Commercial and Applied Holography. A poster session permitted more in-depth discussion between authors and the audience. Two exhibitions of holographic works opened at ISDH: an informal display area at the symposium, and a 15-month-long MIT Museum exhibition, The Jeweled Net: Views of Contemporary Holography. The success of an event of this sort requires the help of many people and organizations. We wish especially to recognize our Honorary Conference Chairs: Tung H Jeong and Joseph W Goodman; our Technical Program Committee: Hans I Bjelkhagen, Frank Fan, Nasser Peyghambarian, and Hiroshi Yoshikawa; and our Arts and Exhibition Committee: Betsy Connors-Chen, Melissa Crenshaw, John Durant, Dieter Jung, Linda Law, Martin Richardson, Jonathan Ross, and Sally Weber. Betsy also coordinated the on-site exhibition. Kristin Hall at the MIT Media Lab made local arrangements, while registration was handled by MIT Conference Services. We also gratefully acknowledge support from Lake Forest College, holographer.org, and authentibrand

Nonacademic Effects of Homework in Privileged, High-Performing High Schools

ERIC Educational Resources Information Center

Galloway, Mollie; Conner, Jerusha; Pope, Denise

2013-01-01

This study used survey data to examine relations among homework, student well-being, and behavioral engagement in a sample of 4,317 students from 10 high-performing high schools in upper middle class communities. Results indicated that students in these schools average more than 3 hr of homework per night. Students who did more hours of homework…

High voltage coaxial switch

DOEpatents

Rink, J.P.

1983-07-19

A coaxial high voltage, high current switch having a solid cylindrical cold cathode coaxially surrounded by a thin hollow cylindrical inner electrode and a larger hollow cylindrical outer electrode. A high voltage trigger between the cathode and the inner electrode causes electrons to be emitted from the cathode and flow to the inner electrode preferably through a vacuum. Some of the electrons penetrate the inner electrode and cause a volumetric discharge in the gas (which may be merely air) between the inner and outer electrodes. The discharge provides a low impedance path between a high voltage charge placed on the outer electrode and a load (which may be a high power laser) coupled to the inner electrode. For high repetition rate the gas between the inner and outer electrodes may be continuously exchanged or refreshed under pressure. 3 figs.

High voltage coaxial switch

DOEpatents

Rink, John P.

1983-07-19

A coaxial high voltage, high current switch having a solid cylindrical cold cathode coaxially surrounded by a thin hollow cylindrical inner electrode and a larger hollow cylindrical outer electrode. A high voltage trigger between the cathode and the inner electrode causes electrons to be emitted from the cathode and flow to the inner electrode preferably through a vacuum. Some of the electrons penetrate the inner electrode and cause a volumetric discharge in the gas (which may be merely air) between the inner and outer electrodes. The discharge provides a low impedance path between a high voltage charge placed on the outer electrode and a load (which may be a high power laser) coupled to the inner electrode. For high repetition rate the gas between the inner and outer electrodes may be continuously exchanged or refreshed under pressure.

High-precision processing and detection of the high-caliber off-axis aspheric mirror

NASA Astrophysics Data System (ADS)

Dai, Chen; Li, Ang; Xu, Lingdi; Zhang, Yingjie

2017-10-01

To achieve the efficient, controllable, digital processing and high-precision detection of the high-caliber off-axis aspheric mirror, meeting the high-level development needs of the modern high-resolution, large field of space optical remote sensing camera, we carried out the research on high precision machining and testing technology of off-axis aspheric mirror. First, we forming the off-axis aspheric sample with diameter of 574mm × 302mm by milling it with milling machine, and then the intelligent robot equipment was used for off-axis aspheric high precision polishing. Surface detection of the sample will be proceed with the off-axis aspheric contact contour detection technology and offaxis non-spherical surface interference detection technology after its fine polishing using ion beam equipment. The final surface accuracy RMS is 12nm.

High Redshift Quasars

NASA Technical Reports Server (NTRS)

Elvis, Martin S.

1996-01-01

The report for this period includes three papers: 'Associated Absorption at Low and High Redshift'; 'Strong X-ray Absorption in a Broad Absorption Line Quasar: PHL5200'; and 'ASCA and ROSAT X-ray Spectra of High-Redshift Radio-Loud Quasars'. The first gives examples from both low and high redshift for combining information on absorbing material in active galactic nuclei from both x-ray and the UV. The second presents ASCA observations of the z = 1.98 prototype broad absorption line quasar (BALQSO): PHL 5200, detected with both the solid-state imaging spectrometers and the gas imaging spectometers. The third paper presents results on the x-ray properties of 9 high-redshift radio-loud quasars observed by ASCA and ROSAT, including ASCA observations of S5 0014+81 (z = 3.38) and S5 0836+71 (z = 2.17) and ROSAT observations of PKS 2126-158.

High pressure furnace

DOEpatents

Morris, D.E.

1993-09-14

A high temperature high pressure furnace has a hybrid partially externally heated construction. A metallic vessel fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum)). The disclosed alloy is fabricated into 11/4 or 2 inch, 32 mm or 50 mm bar stock and has a length of about 22 inches, 56 cm. This bar stock has an aperture formed therein to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the vessel is provided with a small blind aperture into which a thermocouple can be inserted. The closed end of the vessel is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior. 19 figures.

High pressure furnace

DOEpatents

Morris, Donald E.

1993-01-01

A high temperature high pressure furnace has a hybrid partially externally heated construction. A metallic vessel fabricated from an alloy having a composition of at least 45% nickel, 15% chrome, and 10% tungsten is utilized (the preferred alloy including 55% nickel, 22% chrome, 14% tungsten, 2% molybdenum, 3% iron (maximum) and 5% cobalt (maximum). The disclosed alloy is fabricated into 11/4 or 2 inch, 32 mm or 50 mm bar stock and has a length of about 22 inches, 56 cm. This bar stock has an aperture formed therein to define a closed high temperature, high pressure oxygen chamber. The opposite and closed end of the vessel is provided with a small blind aperture into which a thermocouple can be inserted. The closed end of the vessel is inserted into an oven, preferably heated by standard nickel chrome electrical elements and having a heavily insulated exterior.

When high-volume PCI operators in high-volume hospitals move to lower volume hospitals-Do they still maintain high volume and quality of outcomes?

PubMed

Lu, Tsung-Hsueh; Li, Sheng-Tun; Liang, Fu-Wen; Lee, Jo-Chi; Yin, Wei-Hsian

2017-10-31

The aim of this quasi-experimental study was to examine whether high-volume percutaneous coronary intervention (PCI) operators still maintain high volume and quality of outcomes when they moved to lower volume hospitals. Systematic reviews have indicated that high-volume PCI operators and hospitals have higher quality outcomes. However, little is known on whether high PCI volume and high quality outcomes are mainly due to operator characteristics (i.e., skill and experience) and is portable across organizations or whether it is due to hospital characteristics (i.e., equipment, team, and management system) and is less portable. We used Taiwan National Health Insurance claims data 2000-2012 to identify 98 high-volume PCI operators, 10 of whom moved from one hospital to another during the study period. We compared the PCI volume, risk-adjusted mortality ratio, and major adverse cardiovascular event (MACE) ratio before and after moving. Of the 10 high-volume operators who moved, 6 moved from high- to moderate- or low-volume hospitals, with median annual PCI volumes (interquartile range) of 130 (117-165) in prior hospitals and 54 (46-84) in subsequent hospitals (the hospital the operator moved to), and the remaining 4 moved from high to high-volume hospitals, with median annual PCI volumes (interquartile range) of 151 (133-162) in prior hospitals and 193 (178-239) in subsequent hospitals. No significant differences were observed in the risk-adjusted mortality ratios and MACE ratios between high-volume operators and matched controls before and after moving. High-volume operators cannot maintain high volume when they moved from high to moderate or low-volume hospitals; however, the quality of care is maintained. High PCI volume and high-quality outcomes are less portable and more hospital bound. © 2017 Wiley Periodicals, Inc.

High performance, high bandgap, lattice-mismatched, GaInP solar cells

DOEpatents

Wanlass, Mark W; Carapella, Jeffrey J; Steiner, Myles A

2016-11-01

High performance, high bandgap, lattice-mismatched, photovoltaic cells (10), both transparent and non-transparent to sub-bandgap light, are provided as devices for use alone or in combination with other cells in split spectrum apparatus or other applications.

High performance, high bandgap, lattice-mismatched, GaInP solar cells

DOEpatents

Wanlass, Mark W.; Carapella, Jeffrey J.; Steiner, Myles A.

2014-07-08

High performance, high bandgap, lattice-mismatched, photovoltaic cells (10), both transparent and non-transparent to sub-bandgap light, are provided as devices for use alone or in combination with other cells in split spectrum apparatus or other applications.

Precipitation-Strengthened, High-Temperature, High-Force Shape Memory Alloys

NASA Technical Reports Server (NTRS)

Noebe, Ronald D.; Draper, Susan L.; Nathal, Michael V.; Crombie, Edwin A.

2008-01-01

Shape memory alloys (SMAs) are an enabling component in the development of compact, lightweight, durable, high-force actuation systems particularly for use where hydraulics or electrical motors are not practical. However, commercial shape memory alloys based on NiTi are only suitable for applications near room temperature, due to their relatively low transformation temperatures, while many potential applications require higher temperature capability. Consequently, a family of (Ni,Pt)(sub 1-x)Ti(sub x) shape memory alloys with Ti concentrations ranging from about 15 to 25 at.% have been developed for applications in which there are requirements for SMA actuators to exert high forces at operating temperatures higher than those of conventional binary NiTi SMAs. These alloys can be heat treated in the range of 500 C to produce a series of fine precipitate phases that increase the strength of alloy while maintaining a high transformation temperature, even in Ti-lean compositions.

Combining high biodiversity with high yields in tropical agroforests

PubMed Central

Clough, Yann; Barkmann, Jan; Juhrbandt, Jana; Kessler, Michael; Wanger, Thomas Cherico; Anshary, Alam; Buchori, Damayanti; Cicuzza, Daniele; Darras, Kevin; Putra, Dadang Dwi; Erasmi, Stefan; Pitopang, Ramadhanil; Schmidt, Carsten; Schulze, Christian H.; Seidel, Dominik; Steffan-Dewenter, Ingolf; Stenchly, Kathrin; Vidal, Stefan; Weist, Maria; Wielgoss, Arno Christian; Tscharntke, Teja

2011-01-01

Local and landscape-scale agricultural intensification is a major driver of global biodiversity loss. Controversially discussed solutions include wildlife-friendly farming or combining high-intensity farming with land-sparing for nature. Here, we integrate biodiversity and crop productivity data for smallholder cacao in Indonesia to exemplify for tropical agroforests that there is little relationship between yield and biodiversity under current management, opening substantial opportunities for wildlife-friendly management. Species richness of trees, fungi, invertebrates, and vertebrates did not decrease with yield. Moderate shade, adequate labor, and input level can be combined with a complex habitat structure to provide high biodiversity as well as high yields. Although livelihood impacts are held up as a major obstacle for wildlife-friendly farming in the tropics, our results suggest that in some situations, agroforests can be designed to optimize both biodiversity and crop production benefits without adding pressure to convert natural habitat to farmland. PMID:21536873

Engineering High-Energy Interfacial Structures for High-Performance Oxygen-Involving Electrocatalysis.

PubMed

Guo, Chunxian; Zheng, Yao; Ran, Jingrun; Xie, Fangxi; Jaroniec, Mietek; Qiao, Shi-Zhang

2017-07-10

Engineering high-energy interfacial structures for high-performance electrocatalysis is achieved by chemical coupling of active CoO nanoclusters and high-index facet Mn 3 O 4 nano-octahedrons (hi-Mn 3 O 4 ). A thorough characterization, including synchrotron-based near edge X-ray absorption fine structure, reveals that strong interactions between both components promote the formation of high-energy interfacial Mn-O-Co species and high oxidation state CoO, from which electrons are drawn by Mn III -O present in hi-Mn 3 O 4 . The CoO/hi-Mn 3 O 4 demonstrates an excellent catalytic performance over the conventional metal oxide-based electrocatalysts, which is reflected by 1.2 times higher oxygen evolution reaction (OER) activity than that of Ru/C and a comparable oxygen reduction reaction (ORR) activity to that of Pt/C as well as a better stability than that of Ru/C (95 % vs. 81 % retained OER activity) and Pt/C (92 % vs. 78 % retained ORR activity after 10 h running) in alkaline electrolyte. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Combined high vacuum/high frequency fatigue tester

NASA Technical Reports Server (NTRS)

Honeycutt, C. R.; Martin, T. F.

1971-01-01

Apparatus permits application of significantly greater number of cycles or equivalent number of cycles in shorter time than conventional fatigue test machines. Environment eliminates problems associated with high temperature oxidation and with sensitivity of refractory alloy behavior to atmospheric contamination.

High performance carbon fibers from very high molecular weight polyacrylonitrile precursors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morris, E. Ashley; Weisenberger, Matthew C.; Abdallah, Mohamed G.

In this study, carbon fibers are unique reinforcing agents for lightweight composite materials due to their outstanding mechanical properties and low density. Current technologies are capable of producing carbon fibers with 90-95% of the modulus of perfect graphite (~1025 GPa). However, these same carbon fibers possess less than 10% of the theoretical carbon fiber strength, estimated to be about 100 GPa.[1] Indeed, attempts to increase carbon fiber rigidity results in lower breaking strength. To develop advanced carbon fibers with both very high strength and modulus demands a new manufacturing methodology. Here, we report a method of manufacturing high strength, verymore » high modulus carbon fibers from a very high molecular weight (VHMW) polyacrylonitrile (PAN) precursor without the use of nanomaterial additives such as nucleating or structure-templating agents, as have been used by others.[2,3]« less

High performance carbon fibers from very high molecular weight polyacrylonitrile precursors

DOE PAGES

Morris, E. Ashley; Weisenberger, Matthew C.; Abdallah, Mohamed G.; ...

2016-02-02

In this study, carbon fibers are unique reinforcing agents for lightweight composite materials due to their outstanding mechanical properties and low density. Current technologies are capable of producing carbon fibers with 90-95% of the modulus of perfect graphite (~1025 GPa). However, these same carbon fibers possess less than 10% of the theoretical carbon fiber strength, estimated to be about 100 GPa.[1] Indeed, attempts to increase carbon fiber rigidity results in lower breaking strength. To develop advanced carbon fibers with both very high strength and modulus demands a new manufacturing methodology. Here, we report a method of manufacturing high strength, verymore » high modulus carbon fibers from a very high molecular weight (VHMW) polyacrylonitrile (PAN) precursor without the use of nanomaterial additives such as nucleating or structure-templating agents, as have been used by others.[2,3]« less

High power microwave generator

DOEpatents

Ekdahl, Carl A.

1986-01-01

A microwave generator efficiently converts the energy of an intense relativistic electron beam (REB) into a high-power microwave emission using the Smith-Purcell effect which is related to Cerenkov radiation. Feedback for efficient beam bunching and high gain is obtained by placing a cylindrical Smith-Purcell transmission grating on the axis of a toroidal resonator. High efficiency results from the use of a thin cold annular highly-magnetized REB that is closely coupled to the resonant structure.

High power microwave generator

DOEpatents

Ekdahl, C.A.

1983-12-29

A microwave generator efficiently converts the energy of an intense relativistic electron beam (REB) into a high-power microwave emission using the Smith-Purcell effect which is related to Cerenkov radiation. Feedback for efficient beam bunching and high gain is obtained by placing a cylindrical Smith-Purcell transmission grating on the axis of a toroidal resonator. High efficiency results from the use of a thin cold annular highly-magnetized REB that is closely coupled to the resonant structure.

High lift selected concepts

NASA Technical Reports Server (NTRS)

Henderson, M. L.

1979-01-01

The benefits to high lift system maximum life and, alternatively, to high lift system complexity, of applying analytic design and analysis techniques to the design of high lift sections for flight conditions were determined and two high lift sections were designed to flight conditions. The influence of the high lift section on the sizing and economics of a specific energy efficient transport (EET) was clarified using a computerized sizing technique and an existing advanced airplane design data base. The impact of the best design resulting from the design applications studies on EET sizing and economics were evaluated. Flap technology trade studies, climb and descent studies, and augmented stability studies are included along with a description of the baseline high lift system geometry, a calculation of lift and pitching moment when separation is present, and an inverse boundary layer technique for pressure distribution synthesis and optimization.

Highly efficient and high-power diode-pumped femtosecond Yb:LYSO laser

NASA Astrophysics Data System (ADS)

Tian, Wenlong; Wang, Zhaohua; Zhu, Jiangfeng; Zheng, Lihe; Xu, Jun; Wei, Zhiyi

2017-04-01

A diode-pumped high-power femtosecond Yb:LYSO laser with high efficiency is demonstrated. With a semiconductor saturable absorber mirror for passive mode-locking and a Gires-Tournois interferometer mirror for intracavity dispersion compensation, stable mode-locking pulses of 297 fs duration at 1042 nm were obtained. The maximum average power of 3.07 W was realized under 5.17 W absorbed pump power, corresponding to as high as 59.4% opt-opt efficiency. The single pulse energy and peak power are about 35.5 nJ and 119.5 kW, respectively.

High-speed and high-ratio referential genome compression.

PubMed

Liu, Yuansheng; Peng, Hui; Wong, Limsoon; Li, Jinyan

2017-11-01

The rapidly increasing number of genomes generated by high-throughput sequencing platforms and assembly algorithms is accompanied by problems in data storage, compression and communication. Traditional compression algorithms are unable to meet the demand of high compression ratio due to the intrinsic challenging features of DNA sequences such as small alphabet size, frequent repeats and palindromes. Reference-based lossless compression, by which only the differences between two similar genomes are stored, is a promising approach with high compression ratio. We present a high-performance referential genome compression algorithm named HiRGC. It is based on a 2-bit encoding scheme and an advanced greedy-matching search on a hash table. We compare the performance of HiRGC with four state-of-the-art compression methods on a benchmark dataset of eight human genomes. HiRGC takes <30 min to compress about 21 gigabytes of each set of the seven target genomes into 96-260 megabytes, achieving compression ratios of 217 to 82 times. This performance is at least 1.9 times better than the best competing algorithm on its best case. Our compression speed is also at least 2.9 times faster. HiRGC is stable and robust to deal with different reference genomes. In contrast, the competing methods' performance varies widely on different reference genomes. More experiments on 100 human genomes from the 1000 Genome Project and on genomes of several other species again demonstrate that HiRGC's performance is consistently excellent. The C ++ and Java source codes of our algorithm are freely available for academic and non-commercial use. They can be downloaded from https://github.com/yuansliu/HiRGC. jinyan.li@uts.edu.au. Supplementary data are available at Bioinformatics online. © The Author (2017). Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com

High-Temperature, High-Load-Capacity Radial Magnetic Bearing

NASA Technical Reports Server (NTRS)

Provenza, Andrew; Montague, Gerald; Kascak, Albert; Palazzolo, Alan; Jansen, Ralph; Jansen, Mark; Ebihara, Ben

2005-01-01

A radial heteropolar magnetic bearing capable of operating at a temperature as high as 1,000 F (=540 C) has been developed. This is a prototype of bearings for use in gas turbine engines operating at temperatures and speeds much higher than can be withstood by lubricated rolling-element bearings. It is possible to increase the maximum allowable operating temperatures and speeds of rolling-element bearings by use of cooling-air systems, sophisticated lubrication systems, and rotor-vibration- damping systems that are subsystems of the lubrication systems, but such systems and subsystems are troublesome. In contrast, a properly designed radial magnetic bearing can suspend a rotor without contact, and, hence, without need for lubrication or for cooling. Moreover, a magnetic bearing eliminates the need for a separate damping system, inasmuch as a damping function is typically an integral part of the design of the control system of a magnetic bearing. The present high-temperature radial heteropolar magnetic bearing has a unique combination of four features that contribute to its suitability for the intended application: 1. The wires in its electromagnet coils are covered with an insulating material that does not undergo dielectric breakdown at high temperature and is pliable enough to enable the winding of the wires to small radii. 2. The processes used in winding and potting of the coils yields a packing factor close to 0.7 . a relatively high value that helps in maximizing the magnetic fields generated by the coils for a given supplied current. These processes also make the coils structurally robust. 3. The electromagnets are of a modular C-core design that enables replacement of components and semiautomated winding of coils. 4. The stator is mounted in such a manner as to provide stable support under radial and axial thermal expansion and under a load as large as 1,000 lb (.4.4 kN).

High pressure/high temperature thermogravimetric apparatus. Final report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Calo, J.M.; Suuberg, E.M.

1999-12-01

The purpose of this instrumentation grant was to acquire a state-of-the-art, high pressure, high temperature thermogravimetric apparatus (HP/HT TGA) system for the study of the interactions between gases and carbonaceous solids for the purpose of solving problems related to coal utilization and applications of carbon materials. The instrument that we identified for this purpose was manufactured by DMT (Deutsche Montan Technologies)--Institute of Cokemaking and Coal Chemistry of Essen, Germany. Particular features of note include: Two reactors: a standard TGA reactor, capable of 1100 C at 100 bar; and a high temperature (HT) reactor, capable of operation at 1600 C andmore » 100 bar; A steam generator capable of generating steam to 100 bar; Flow controllers and gas mixing system for up to three reaction gases, plus a separate circuit for steam, and another for purge gas; and An automated software system for data acquisition and control. The HP/TP DMT-TGA apparatus was purchased in 1996 and installed and commissioned during the summer of 1996. The apparatus was located in Room 128 of the Prince Engineering Building at Brown University. A hydrogen alarm and vent system were added for safety considerations. The system has been interfaced to an Ametek quadruple mass spectrometer (MA 100), pumped by a Varian V250 turbomolecular pump, as provided for in the original proposed. With this capability, a number of gas phase species of interest can be monitored in a near-simultaneous fashion. The MS can be used in a few different modes. During high pressure, steady-state gasification experiments, it is used to sample, measure, and monitor the reactant/product gases. It can also be used to monitor gas phase species during nonisothermal temperature programmed reaction (TPR) or temperature programmed desorption (TPD) experiments.« less

High-Reproducibility and High-Accuracy Method for Automated Topic Classification

NASA Astrophysics Data System (ADS)

Lancichinetti, Andrea; Sirer, M. Irmak; Wang, Jane X.; Acuna, Daniel; Körding, Konrad; Amaral, Luís A. Nunes

2015-01-01

Much of human knowledge sits in large databases of unstructured text. Leveraging this knowledge requires algorithms that extract and record metadata on unstructured text documents. Assigning topics to documents will enable intelligent searching, statistical characterization, and meaningful classification. Latent Dirichlet allocation (LDA) is the state of the art in topic modeling. Here, we perform a systematic theoretical and numerical analysis that demonstrates that current optimization techniques for LDA often yield results that are not accurate in inferring the most suitable model parameters. Adapting approaches from community detection in networks, we propose a new algorithm that displays high reproducibility and high accuracy and also has high computational efficiency. We apply it to a large set of documents in the English Wikipedia and reveal its hierarchical structure.

High-speed and high-fidelity system and method for collecting network traffic

DOEpatents

Weigle, Eric H [Los Alamos, NM

2010-08-24

A system is provided for the high-speed and high-fidelity collection of network traffic. The system can collect traffic at gigabit-per-second (Gbps) speeds, scale to terabit-per-second (Tbps) speeds, and support additional functions such as real-time network intrusion detection. The present system uses a dedicated operating system for traffic collection to maximize efficiency, scalability, and performance. A scalable infrastructure and apparatus for the present system is provided by splitting the work performed on one host onto multiple hosts. The present system simultaneously addresses the issues of scalability, performance, cost, and adaptability with respect to network monitoring, collection, and other network tasks. In addition to high-speed and high-fidelity network collection, the present system provides a flexible infrastructure to perform virtually any function at high speeds such as real-time network intrusion detection and wide-area network emulation for research purposes.

Prevalence of tobacco use among junior high and senior high school students in Taiwan.

PubMed

Chen, Ping-Ling; Huang, Weigang; Chuang, Yi-Li; Warren, Charles W; Jones, Nathan R; Asma, Samira

2008-12-01

Tobacco use is a major preventable cause of death in the world. This article describes and compares tobacco use prevalence for students attending junior high schools and senior high schools in Taiwan. This report uses data from the Global Youth Tobacco Survey (GYTS) completed among 4689 junior high school students and 4426 senior high school students in Taiwan in 2004-2005. The GYTS uses a 2-stage sampling design to produce nationally representative data for junior and senior high students in general and vocational schools. Higher smoking prevalence was observed among senior high (10.1% general schools and 15.9% vocational schools) than junior high (5.5%) school students. Smoking prevalence of girls in junior high (3.2%) and senior high schools (4.6% general and 11.1% vocational) was almost as high or higher than adult females' (4.3%) smoking rates. The pattern of smoking intensity across school years and type of school shows that the percentage of smokers who were experimenters (47.1%) was higher in junior high school and the percentage of smokers who were regular/established smokers (over 50%) was higher in senior high school. Smoking prevalence described in this report shows that there are challenges facing the tobacco prevention and control program in Taiwan. The findings suggest that schools should increase their smoking initiation prevention efforts and make available cessation programs and counseling to help students quit smoking. If effective youth tobacco control programs are not developed and implemented in Taiwan, future morbidity and mortality attributed to tobacco will surely increase, especially among women.

Boriding of high carbon high chromium cold work tool steel

NASA Astrophysics Data System (ADS)

Muhammad, W.

2014-06-01

High-carbon high-chromium cold work tool steels are widely used for blanking and cold forming of punches and dies. It is always advantageous to obtain an increased wear resistant surface to improve life and performance of these steels. In this connection boriding of a high-carbon high-chromium cold work die steel, D3, was conducted in a mixture of 30% B4C, 70% borax at 950 °C for two, four and six hours. Case depth of the borided layer obtained was between 40 to 80 μm. After boriding, the surface hardness achieved was between 1430 to 1544 HV depending upon the process time. X-ray diffraction studies confirmed the formation of a duplex compound layer consisting of FeB and Fe2B. It is generally considered that FeB is undesirable because of its inherent brittleness. Post boriding treatment (homogenization) transformed the compound layer into single-phase layer of Fe2B, while surface hardness decreased to 1345-1430 HV. Pin-on-disc wer test showed that wear resistance of the borided samples was superior as compared to non-borided material and increased with boriding time.

Gasification of high ash, high ash fusion temperature bituminous coals

DOEpatents

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

High-Capacity, High-Voltage Composite Oxide Cathode Materials

NASA Technical Reports Server (NTRS)

Hagh, Nader M.

2015-01-01

This SBIR project integrates theoretical and experimental work to enable a new generation of high-capacity, high-voltage cathode materials that will lead to high-performance, robust energy storage systems. At low operating temperatures, commercially available electrode materials for lithium-ion (Li-ion) batteries do not meet energy and power requirements for NASA's planned exploration activities. NEI Corporation, in partnership with the University of California, San Diego, has developed layered composite cathode materials that increase power and energy densities at temperatures as low as 0 degC and considerably reduce the overall volume and weight of battery packs. In Phase I of the project, through innovations in the structure and morphology of composite electrode particles, the partners successfully demonstrated an energy density exceeding 1,000 Wh/kg at 4 V at room temperature. In Phase II, the team enhanced the kinetics of Li-ion transport and electronic conductivity at 0 degC. An important feature of the composite cathode is that it has at least two components that are structurally integrated. The layered material is electrochemically inactive; however, upon structural integration with a spinel material, the layered material can be electrochemically activated and deliver a large amount of energy with stable cycling.

Flexible asymmetric supercapacitors with high energy and high power density in aqueous electrolytes

NASA Astrophysics Data System (ADS)

Cheng, Yingwen; Zhang, Hongbo; Lu, Songtao; Varanasi, Chakrapani V.; Liu, Jie

2013-01-01

Supercapacitors with both high energy and high power densities are critical for many practical applications. In this paper, we discuss the design and demonstrate the fabrication of flexible asymmetric supercapacitors based on nanocomposite electrodes of MnO2, activated carbon, carbon nanotubes and graphene. The combined unique properties of each of these components enable highly flexible and mechanically strong films that can serve as electrodes directly without using any current collectors or binders. Using these flexible electrodes and a roll-up approach, asymmetric supercapacitors with 2 V working voltage were successfully fabricated. The fabricated device showed excellent rate capability, with 78% of the original capacitance retained when the scan rate was increased from 2 mV s-1 to 500 mV s-1. Owing to the unique composite structure, these supercapacitors were able to deliver high energy density (24 W h kg-1) under high power density (7.8 kW kg-1) conditions. These features could enable supercapacitor based energy storage systems to be very attractive for a variety of critical applications, such as the power sources in hybrid electric vehicles and the back-up powers for wind and solar energy, where both high energy density and high power density are required.Supercapacitors with both high energy and high power densities are critical for many practical applications. In this paper, we discuss the design and demonstrate the fabrication of flexible asymmetric supercapacitors based on nanocomposite electrodes of MnO2, activated carbon, carbon nanotubes and graphene. The combined unique properties of each of these components enable highly flexible and mechanically strong films that can serve as electrodes directly without using any current collectors or binders. Using these flexible electrodes and a roll-up approach, asymmetric supercapacitors with 2 V working voltage were successfully fabricated. The fabricated device showed excellent rate capability, with 78% of

Workshop on High Power ICH Antenna Designs for High Density Tokamaks

NASA Astrophysics Data System (ADS)

Aamodt, R. E.

1990-02-01

A workshop in high power ICH antenna designs for high density tokamaks was held to: (1) review the data base relevant to the high power heating of high density tokamaks; (2) identify the important issues which need to be addressed in order to ensure the success of the ICRF programs on CIT and Alcator C-MOD; and (3) recommend approaches for resolving the issues in a timely realistic manner. Some specific performance goals for the antenna system define a successful design effort. Simply stated these goals are: couple the specified power per antenna into the desired ion species; produce no more than an acceptable level of RF auxiliary power induced impurities; and have a mechanical structure which safely survives the thermal, mechanical and radiation stresses in the relevant environment. These goals are intimately coupled and difficult tradeoffs between scientific and engineering constraints have to be made.

Precision optical slit for high heat load or ultra high vacuum

DOEpatents

Andresen, Nord C.; DiGennaro, Richard S.; Swain, Thomas L.

1995-01-01

This invention relates generally to slits used in optics that must be precisely aligned and adjusted. The optical slits of the present invention are useful in x-ray optics, x-ray beam lines, optical systems in which the entrance slit is critical for high wavelength resolution. The invention is particularly useful in ultra high vacuum systems where lubricants are difficult to use and designs which avoid the movement of metal parts against one another are important, such as monochrometers for high wavelength resolution with ultra high vacuum systems. The invention further relates to optical systems in which temperature characteristics of the slit materials is important. The present invention yet additionally relates to precision slits wherein the opposing edges of the slit must be precisely moved relative to a center line between the edges with each edge retaining its parallel orientation with respect to the other edge and/or the center line.

Ultra-high resolution and high-brightness AMOLED

NASA Astrophysics Data System (ADS)

Wacyk, Ihor; Ghosh, Amal; Prache, Olivier; Draper, Russ; Fellowes, Dave

2012-06-01

As part of its continuing effort to improve both the resolution and optical performance of AMOLED microdisplays, eMagin has recently developed an SXGA (1280×3×1024) microdisplay under a US Army RDECOM CERDEC NVESD contract that combines the world's smallest OLED pixel pitch with an ultra-high brightness green OLED emitter. This development is aimed at next-generation HMD systems with "see-through" and daylight imaging requirements. The OLED pixel array is built on a 0.18-micron CMOS backplane and contains over 4 million individually addressable pixels with a pixel pitch of 2.7 × 8.1 microns, resulting in an active area of 0.52 inches diagonal. Using both spatial and temporal enhancement, the display can provide over 10-bits of gray-level control for high dynamic range applications. The new pixel design also enables the future implementation of a full-color QSXGA (2560 × RGB × 2048) microdisplay in an active area of only 1.05 inch diagonal. A low-power serialized low-voltage-differential-signaling (LVDS) interface is integrated into the display for use as a remote video link for tethered systems. The new SXGA backplane has been combined with the high-brightness green OLED device developed by eMagin under an NVESD contract. This OLED device has produced an output brightness of more than 8000fL with all pixels on; lifetime measurements are currently underway and will presented at the meeting. This paper will describe the operational features and first optical and electrical test results of the new SXGA demonstrator microdisplay.

High and Dry

ERIC Educational Resources Information Center

Johnson, Robert L.

2005-01-01

High-performance schools are facilities that improve the learning environment while saving energy, resources and money. Creating a high-performance school requires an integrated design approach. Key systems--including lighting, HVAC, electrical and plumbing--must be considered from the beginning of the design process. According to William H.…

High Thermoelectric Power Factor of High-Mobility 2D Electron Gas.

PubMed

Ohta, Hiromichi; Kim, Sung Wng; Kaneki, Shota; Yamamoto, Atsushi; Hashizume, Tamotsu

2018-01-01

Thermoelectric conversion is an energy harvesting technology that directly converts waste heat from various sources into electricity by the Seebeck effect of thermoelectric materials with a large thermopower ( S ), high electrical conductivity (σ), and low thermal conductivity (κ). State-of-the-art nanostructuring techniques that significantly reduce κ have realized high-performance thermoelectric materials with a figure of merit ( ZT = S 2 ∙σ∙ T ∙κ -1 ) between 1.5 and 2. Although the power factor (PF = S 2 ∙σ) must also be enhanced to further improve ZT , the maximum PF remains near 1.5-4 mW m -1 K -2 due to the well-known trade-off relationship between S and σ. At a maximized PF, σ is much lower than the ideal value since impurity doping suppresses the carrier mobility. A metal-oxide-semiconductor high electron mobility transistor (MOS-HEMT) structure on an AlGaN/GaN heterostructure is prepared. Applying a gate electric field to the MOS-HEMT simultaneously modulates S and σ of the high-mobility electron gas from -490 µV K -1 and ≈10 -1 S cm -1 to -90 µV K -1 and ≈10 4 S cm -1 , while maintaining a high carrier mobility (≈1500 cm 2 V -1 s -1 ). The maximized PF of the high-mobility electron gas is ≈9 mW m -1 K -2 , which is a two- to sixfold increase compared to state-of-the-art practical thermoelectric materials.

Aromatic Polythiourea Dielectrics with High Energy Density, High Breakdown Strength, and Low Dielectric Loss

NASA Astrophysics Data System (ADS)

Wu, Shan; Burlingame, Quinn; Lin, Minren; Zhang, Qiming

2013-03-01

There is an increasing demand on dielectric materials with high electric energy density and low loss for a broad range of applications in modern electronics and electrical power systems such as hybrid electric vehicles (HEV), medical defibrillators, filters, and switched-mode power supplies. One major challenge in developing dielectric polymers is how to achieve high energy density Ue while maintaining low dielectric loss, even at very high-applied electric fields. Here we show that amorphous polar-polymers with very low impurity concentration can be promising for realizing such a dielectric polymer. Polar-polymer with high dipole moment and weak dipole coupling can provide relatively high dielectric constant for high Ue, eliminate polarization and conduction losses due to weak dipolar coupling and strong polar-scattering to charge carriers. Indeed, an aromatic polythiourea thin film can maintain low loss to high fields (>1 GV/m) with a high Ue (~ 24 J/cm3) , which is very attractive for energy storage capacitors.

High bandgap III-V alloys for high efficiency optoelectronics

DOEpatents

Alberi, Kirstin; Mascarenhas, Angelo; Wanlass, Mark

2017-01-10

High bandgap alloys for high efficiency optoelectronics are disclosed. An exemplary optoelectronic device may include a substrate, at least one Al.sub.1-xIn.sub.xP layer, and a step-grade buffer between the substrate and at least one Al.sub.1-xIn.sub.xP layer. The buffer may begin with a layer that is substantially lattice matched to GaAs, and may then incrementally increase the lattice constant in each sequential layer until a predetermined lattice constant of Al.sub.1-xIn.sub.xP is reached.

High throughput screening of ligand binding to macromolecules using high resolution powder diffraction

DOEpatents

Von Dreele, Robert B.; D'Amico, Kevin

2006-10-31

A process is provided for the high throughput screening of binding of ligands to macromolecules using high resolution powder diffraction data including producing a first sample slurry of a selected polycrystalline macromolecule material and a solvent, producing a second sample slurry of a selected polycrystalline macromolecule material, one or more ligands and the solvent, obtaining a high resolution powder diffraction pattern on each of said first sample slurry and the second sample slurry, and, comparing the high resolution powder diffraction pattern of the first sample slurry and the high resolution powder diffraction pattern of the second sample slurry whereby a difference in the high resolution powder diffraction patterns of the first sample slurry and the second sample slurry provides a positive indication for the formation of a complex between the selected polycrystalline macromolecule material and at least one of the one or more ligands.

Development of high sensitivity and high speed large size blank inspection system LBIS

NASA Astrophysics Data System (ADS)

Ohara, Shinobu; Yoshida, Akinori; Hirai, Mitsuo; Kato, Takenori; Moriizumi, Koichi; Kusunose, Haruhiko

2017-07-01

The production of high-resolution flat panel displays (FPDs) for mobile phones today requires the use of high-quality large-size photomasks (LSPMs). Organic light emitting diode (OLED) displays use several transistors on each pixel for precise current control and, as such, the mask patterns for OLED displays are denser and finer than the patterns for the previous generation displays throughout the entire mask surface. It is therefore strongly demanded that mask patterns be produced with high fidelity and free of defect. To enable the production of a high quality LSPM in a short lead time, the manufacturers need a high-sensitivity high-speed mask blank inspection system that meets the requirement of advanced LSPMs. Lasertec has developed a large-size blank inspection system called LBIS, which achieves high sensitivity based on a laser-scattering technique. LBIS employs a high power laser as its inspection light source. LBIS's delivery optics, including a scanner and F-Theta scan lens, focus the light from the source linearly on the surface of the blank. Its specially-designed optics collect the light scattered by particles and defects generated during the manufacturing process, such as scratches, on the surface and guide it to photo multiplier tubes (PMTs) with high efficiency. Multiple PMTs are used on LBIS for the stable detection of scattered light, which may be distributed at various angles due to irregular shapes of defects. LBIS captures 0.3mμ PSL at a detection rate of over 99.5% with uniform sensitivity. Its inspection time is 20 minutes for a G8 blank and 35 minutes for G10. The differential interference contrast (DIC) microscope on the inspection head of LBIS captures high-contrast review images after inspection. The images are classified automatically.

A Lithium-Air Battery Stably Working at High Temperature with High Rate Performance.

PubMed

Pan, Jian; Li, Houpu; Sun, Hao; Zhang, Ye; Wang, Lie; Liao, Meng; Sun, Xuemei; Peng, Huisheng

2018-02-01

Driven by the increasing requirements for energy supply in both modern life and the automobile industry, the lithium-air battery serves as a promising candidate due to its high energy density. However, organic solvents in electrolytes are likely to rapidly vaporize and form flammable gases under increasing temperatures. In this case, serious safety problems may occur and cause great harm to people. Therefore, a kind of lithium-air that can work stably under high temperature is desirable. Herein, through the use of an ionic liquid and aligned carbon nanotubes, and a fiber shaped design, a new type of lithium-air battery that can effectively work at high temperatures up to 140 °C is developed. Ionic liquids can offer wide electrochemical windows and low vapor pressures, as well as provide high thermal stability for lithium-air batteries. The aligned carbon nanotubes have good electric and heat conductivity. Meanwhile, the fiber format can offer both flexibility and weavability, and realize rapid heat conduction and uniform heat distribution of the battery. In addition, the high temperature has also largely improved the specific powers by increasing the ionic conductivity and catalytic activity of the cathode. Consequently, the lithium-air battery can work stably at 140 °C with a high specific current of 10 A g -1 for 380 cycles, indicating high stability and good rate performance at high temperatures. This work may provide an effective paradigm for the development of high-performance energy storage devices. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Laser imprint suppression using high-Z layers at high foot intensities

NASA Astrophysics Data System (ADS)

Karasik, Max; Aglitskiy, Y.; Serlin, V.; Weaver, J. L.; Bates, J. W.; Phillips, L. S.

2006-10-01

Laser imprint experiments are carried out on the Nike KrF laser with induced spatial incoherence (ISI) smoothing. Most of the imprint occurs during the initial low-intensity (``foot'') part of the pulse, which is necessary to compress the target to achieve high gain. It has been found previously that a thin high-Z overcoat on the laser side of the target can be effective in suppressing imprint [S. P. Obenschain et al. Phys. Plasmas 9, 2234 (2002)]. The present experiments are designed to extend this method to higher foot intensities (˜10^13 W/cm^2), approaching those of the current high gain pellet designs. Measurements of Raleigh-Taylor (RT) amplified areal mass non-uniformity are made by face-on x-ray radiography using Bragg reflection from a curved crystal coupled to an x-ray streak camera. X-ray flux from the high-Z layer is monitored using absolutely calibrated time-resolved x-ray spectrometers. Simultaneous side-on radiography using a curved crystal allows target trajectory measurement for comparison with simulations. The effect of the high-Z layers of varying thicknesses on ISI imprint as well as re-imposed ripple growth will be presented for two different materials (Au and Pd). This work is supported by US DOE/NNSA.

3D printed high performance strain sensors for high temperature applications

NASA Astrophysics Data System (ADS)

Rahman, Md Taibur; Moser, Russell; Zbib, Hussein M.; Ramana, C. V.; Panat, Rahul

2018-01-01

Realization of high temperature physical measurement sensors, which are needed in many of the current and emerging technologies, is challenging due to the degradation of their electrical stability by drift currents, material oxidation, thermal strain, and creep. In this paper, for the first time, we demonstrate that 3D printed sensors show a metamaterial-like behavior, resulting in superior performance such as high sensitivity, low thermal strain, and enhanced thermal stability. The sensors were fabricated using silver (Ag) nanoparticles (NPs), using an advanced Aerosol Jet based additive printing method followed by thermal sintering. The sensors were tested under cyclic strain up to a temperature of 500 °C and showed a gauge factor of 3.15 ± 0.086, which is about 57% higher than that of those available commercially. The sensor thermal strain was also an order of magnitude lower than that of commercial gages for operation up to a temperature of 500 °C. An analytical model was developed to account for the enhanced performance of such printed sensors based on enhanced lateral contraction of the NP films due to the porosity, a behavior akin to cellular metamaterials. The results demonstrate the potential of 3D printing technology as a pathway to realize highly stable and high-performance sensors for high temperature applications.

High-order shock-fitted detonation propagation in high explosives

NASA Astrophysics Data System (ADS)

Romick, Christopher M.; Aslam, Tariq D.

2017-03-01

A highly accurate numerical shock and material interface fitting scheme composed of fifth-order spatial and third- or fifth-order temporal discretizations is applied to the two-dimensional reactive Euler equations in both slab and axisymmetric geometries. High rates of convergence are not typically possible with shock-capturing methods as the Taylor series analysis breaks down in the vicinity of discontinuities. Furthermore, for typical high explosive (HE) simulations, the effects of material interfaces at the charge boundary can also cause significant computational errors. Fitting a computational boundary to both the shock front and material interface (i.e. streamline) alleviates the computational errors associated with captured shocks and thus opens up the possibility of high rates of convergence for multi-dimensional shock and detonation flows. Several verification tests, including a Sedov blast wave, a Zel'dovich-von Neumann-Döring (ZND) detonation wave, and Taylor-Maccoll supersonic flow over a cone, are utilized to demonstrate high rates of convergence to nontrivial shock and reaction flows. Comparisons to previously published shock-capturing multi-dimensional detonations in a polytropic fluid with a constant adiabatic exponent (PF-CAE) are made, demonstrating significantly lower computational error for the present shock and material interface fitting method. For an error on the order of 10 m /s, which is similar to that observed in experiments, shock-fitting offers a computational savings on the order of 1000. In addition, the behavior of the detonation phase speed is examined for several slab widths to evaluate the detonation performance of PBX 9501 while utilizing the Wescott-Stewart-Davis (WSD) model, which is commonly used in HE modeling. It is found that the thickness effect curve resulting from this equation of state and reaction model using published values is dramatically more steep than observed in recent experiments. Utilizing the present fitting

Journalism Beyond High School.

ERIC Educational Resources Information Center

Turner, Sally

2001-01-01

Discusses the shift from high school journalism to college journalism for students. Describes the role of the high school journalism advisor in that process. Offers checklists for getting to know a college publication. Outlines ways high school journalism teachers can take advantage of journalism resources available at local colleges and…

High Technology Needs Assessment.

ERIC Educational Resources Information Center

Southeastern Louisiana Univ., Hammond.

A project produced a high technology status report providing needs assessment data for educational planning. The purpose was to determine the impact and future of high technology in Louisiana. Information was obtained from 68 Louisiana manufacturing industries by mailed questionnaire. Data indicated that 45 industries were involved in high tech. A…

High-pressure high-temperature phase diagram of organic crystal paracetamol

DOE PAGES

Smith, Spencer J.; Montgomery, Jeffrey M.; Vohra, Yogesh K.

2016-01-06

High-pressure high-temperature (HPHT) Raman spectroscopy studies have been performed on the organic crystal paracetamol in a diamond anvil cell utilizing boron-doped heating diamond anvil. Isobaric measurements were conducted at pressures up to 8.5 GPa and temperature up to 520 K in five different experiments. Solid state phase transitions from monoclinic Form I → orthorhombic Form II were observed at various pressures and temperatures as well as transitions from Form II → unknown Form IV. The melting temperature for paracetamol was observed to increase with increasing pressures to 8.5 GPa. As a result, this new data is combined with previous ambientmore » temperature high-pressure Raman and X- ray diffraction data to create the first HPHT phase diagram of paracetamol.« less

High-pressure high-temperature phase diagram of organic crystal paracetamol

NASA Astrophysics Data System (ADS)

Smith, Spencer J.; Montgomery, Jeffrey M.; Vohra, Yogesh K.

2016-01-01

High-pressure high-temperature (HPHT) Raman spectroscopy studies have been performed on the organic crystal paracetamol in a diamond anvil cell utilizing boron-doped heating diamond anvil. Isobaric measurements were conducted at pressures up to 8.5 GPa and temperature up to 520 K in five different experiments. Solid state phase transitions from monoclinic Form I  →  orthorhombic Form II were observed at various pressures and temperatures as well as transitions from Form II  →  unknown Form IV. The melting temperature for paracetamol was observed to increase with increasing pressures to 8.5 GPa. This new data is combined with previous ambient temperature high-pressure Raman and x-ray diffraction data to create the first HPHT phase diagram of paracetamol.

New high-strength steels

NASA Astrophysics Data System (ADS)

Belyakov, L. N.; Petrakov, A. F.; Pokrovskaya, N. G.; Shal'kevich, A. B.

1998-08-01

Steels have found wide application in modern aircraft and are the profile materials in some structures. They are used when a high specific strength, rigidity, fatigue limit, and high-temperature strength are required, for example, in the production of wing bars, longerons, ribs, landing gear parts, and gear transmission mechanisms. Steels used in the aircraft industry should possess high parameters of fracture toughness, crack resistance under static and cyclic loads, and corrosion resistance (for the all-climatic variant) with preservation of a high adaptability to manufacturing (weldability, forgeability, processability).

Precision optical slit for high heat load or ultra high vacuum

DOEpatents

Andresen, N.C.; DiGennaro, R.S.; Swain, T.L.

1995-01-24

This invention relates generally to slits used in optics that must be precisely aligned and adjusted. The optical slits of the present invention are useful in x-ray optics, x-ray beam lines, optical systems in which the entrance slit is critical for high wavelength resolution. The invention is particularly useful in ultra high vacuum systems where lubricants are difficult to use and designs which avoid the movement of metal parts against one another are important, such as monochromators for high wavelength resolution with ultra high vacuum systems. The invention further relates to optical systems in which temperature characteristics of the slit materials is important. The present invention yet additionally relates to precision slits wherein the opposing edges of the slit must be precisely moved relative to a center line between the edges with each edge retaining its parallel orientation with respect to the other edge and/or the center line. 21 figures.

Research at Very High Pressures and High Temperatures

ERIC Educational Resources Information Center

Bundy, Francis P.

1977-01-01

Reviews research and apparatus utilized in the study of the states and characteristics of materials at very high temperatures and pressures. Includes three examples of the research being conducted. (SL)

Nanocrystalline High-Entropy Alloys: A New Paradigm in High-Temperature Strength and Stability.

PubMed

Zou, Yu; Wheeler, Jeffrey M; Ma, Huan; Okle, Philipp; Spolenak, Ralph

2017-03-08

Metals with nanometer-scale grains or nanocrystalline metals exhibit high strengths at ambient conditions, yet their strengths substantially decrease with increasing temperature, rendering them unsuitable for usage at high temperatures. Here, we show that a nanocrystalline high-entropy alloy (HEA) retains an extraordinarily high yield strength over 5 GPa up to 600 °C, 1 order of magnitude higher than that of its coarse-grained form and 5 times higher than that of its single-crystalline equivalent. As a result, such nanostructured HEAs reveal strengthening figures of merit-normalized strength by the shear modulus above 1/50 and strength-to-density ratios above 0.4 MJ/kg, which are substantially higher than any previously reported values for nanocrystalline metals in the same homologous temperature range, as well as low strain-rate sensitivity of ∼0.005. Nanocrystalline HEAs with these properties represent a new class of nanomaterials for high-stress and high-temperature applications in aerospace, civilian infrastructure, and energy sectors.

High temperature alloy

NASA Technical Reports Server (NTRS)

Frank, R. G.; Semmel, J. W., Jr.

1968-01-01

Molybdenum is substituted for tungsten on an atomic basis in a cobalt-based alloy, S-1, thus enabling the alloy to be formed into various mill products, such as tubing and steels. The alloy is weldable, has good high temperature strength and is not subject to embrittlement produced by high temperature aging.

High Functioning Autism.

ERIC Educational Resources Information Center

Reed, Vicki

This paper reviews the characteristics and needs of students with high functioning autism. First, it lists 18 common characteristics of autism, then it stresses that autism is defined by the general pattern of characteristics. Next, it discusses how people with high functioning autism differ from those with autism. These differences include higher…

Ultra Fast, High Rep Rate, High Voltage Spark Gap Pulser

DTIC Science & Technology

1995-07-01

current rise time. The spark gap was designed to have a coaxial geometry reducing its inductance. Provisions were made to pass flowing gas between the...ULTRA FAST, HIGH REP RATE, HIGH VOLTAGE SPARK GAP PULSER Robert A. Pastore Jr., Lawrence E. Kingsley, Kevin Fonda, Erik Lenzing Electrophysics and...Modeling Branch AMSRL-PS-EA Tel.: (908)-532-0271 FAX: (908)-542-3348 U.S. Army Research Laboratory Physical Sciences Directorate Ft. Monmouth

Improved confinement in highly powered high performance scenarios on DIII-D

DOE Office of Scientific and Technical Information (OSTI.GOV)

Petrie, Thomas W.; Osborne, Thomas; Fenstermacher, Max E.

DIII-D has recently demonstrated improved energy confinement by injecting neutral deuterium gas into high performance near-double null divertor (DND) plasmas during high power operation. Representative parameters for these plasmas are: q 95 = 6, P IN up to 15 MW, H 98 = 1.4–1.8, and β N = 2.5–4.0. The ion B xmore » $$\\triangledown$$B direction is away from the primary X-point. While plasma conditions at lower to moderate power input (e.g., 11 MW) are shown to be favorable to successful puff-and-pump radiating divertor applications, particularly when using argon seeds, plasma behavior at higher powers (e.g., ≥14 MW) may make successful puff-and-pump operation more problematic. In contrast to lower powered high performance plasmas, both $$\\tau$$ E and β N in the high power cases (≥14 MW) increased and ELM frequency decreased, as density was raised by deuterium gas injection. Improved performance in the higher power plasmas was tied to higher pedestal pressure, which according to peeling-ballooning mode stability analysis using the ELITE code could increase with density along the kink/peeling stability threshold, while the pedestal pressure gradient in the lower power discharges were limited by the ballooning threshold. This resulted in improved fueling efficiency and ≈10% higher $$\\tau$$ E and β N than is normally observed in comparable high performance plasmas on DIII-D. Applying the puff-and-pump radiating divertor approach at moderate versus high power input is shown to result in a much different evolution in core and pedestal plasma behavior. In conclusion, we find that injecting deuterium gas into these highly powered DND plasmas may open up a new avenue for achieving elevated plasma performance, including better fueling, but the resulting higher density may also complicate application of a radiating divertor approach to heat flux reduction in present-day tokamaks, if scenarios involving second-harmonic electron cyclotron heating are used.« less

Improved confinement in highly powered high performance scenarios on DIII-D

DOE PAGES

Petrie, Thomas W.; Osborne, Thomas; Fenstermacher, Max E.; ...

2017-06-09

DIII-D has recently demonstrated improved energy confinement by injecting neutral deuterium gas into high performance near-double null divertor (DND) plasmas during high power operation. Representative parameters for these plasmas are: q 95 = 6, P IN up to 15 MW, H 98 = 1.4–1.8, and β N = 2.5–4.0. The ion B xmore » $$\\triangledown$$B direction is away from the primary X-point. While plasma conditions at lower to moderate power input (e.g., 11 MW) are shown to be favorable to successful puff-and-pump radiating divertor applications, particularly when using argon seeds, plasma behavior at higher powers (e.g., ≥14 MW) may make successful puff-and-pump operation more problematic. In contrast to lower powered high performance plasmas, both $$\\tau$$ E and β N in the high power cases (≥14 MW) increased and ELM frequency decreased, as density was raised by deuterium gas injection. Improved performance in the higher power plasmas was tied to higher pedestal pressure, which according to peeling-ballooning mode stability analysis using the ELITE code could increase with density along the kink/peeling stability threshold, while the pedestal pressure gradient in the lower power discharges were limited by the ballooning threshold. This resulted in improved fueling efficiency and ≈10% higher $$\\tau$$ E and β N than is normally observed in comparable high performance plasmas on DIII-D. Applying the puff-and-pump radiating divertor approach at moderate versus high power input is shown to result in a much different evolution in core and pedestal plasma behavior. In conclusion, we find that injecting deuterium gas into these highly powered DND plasmas may open up a new avenue for achieving elevated plasma performance, including better fueling, but the resulting higher density may also complicate application of a radiating divertor approach to heat flux reduction in present-day tokamaks, if scenarios involving second-harmonic electron cyclotron heating are used.« less

Principles for high-quality, high-value testing.

PubMed

Power, Michael; Fell, Greg; Wright, Michael

2013-02-01

A survey of doctors working in two large NHS hospitals identified over 120 laboratory tests, imaging investigations and investigational procedures that they considered not to be overused. A common suggestion in this survey was that more training was required. And, this prompted the development of a list of core principles for high-quality, high-value testing. The list can be used as a framework for training and as a reference source. The core principles are: (1) Base testing practices on the best available evidence. (2) Apply the evidence on test performance with careful judgement. (3) Test efficiently. (4) Consider the value (and affordability) of a test before requesting it. (5) Be aware of the downsides and drivers of overdiagnosis. (6) Confront uncertainties. (7) Be patient-centred in your approach. (8) Consider ethical issues. (9) Be aware of normal cognitive limitations and biases when testing. (10) Follow the 'knowledge journey' when teaching and learning these core principles.

Vortices in high-performance high-temperature superconductors

DOE PAGES

Kwok, Wai-Kwong; Welp, Ulrich; Glatz, Andreas; ...

2016-09-21

The behavior of vortex matter in high-temperature superconductors (HTS) controls the entire electromagnetic response of the material, including its current carrying capacity. In this paper, we review the basic concepts of vortex pinning and its application to a complex mixed pinning landscape to enhance the critical current and to reduce its anisotropy. We focus on recent scientific advances that have resulted in large enhancements of the in-field critical current in state-of-the-art second generation (2G) YBCO coated conductors and on the prospect of an isotropic, high-critical current superconductor in the iron-based superconductors. Finally, we discuss an emerging new paradigm of criticalmore » current by design—a drive to achieve a quantitative correlation between the observed critical current density and mesoscale mixed pinning landscapes by using realistic input parameters in an innovative and powerful large-scale time dependent Ginzburg–Landau approach to simulating vortex dynamics.« less

Do Highly Effective Principals Also Have High Levels of Cultural Intelligence?

ERIC Educational Resources Information Center

Naughton, Whitney Michelle

2010-01-01

Purpose: The purpose of this study was to determine if elementary school principals who exhibit characteristics of highly effective principals also possess high levels of cultural intelligence. Methodology: Three instruments were used in this study, combining both qualitative and quantitative approaches to the collection of data. The first…

Unfulfilled Potential: High-Achieving Minority Students and the High School Achievement Gap in Math

ERIC Educational Resources Information Center

Kotok, Stephen

2017-01-01

This study uses multilevel modeling to examine a subset of the highest performing 9th graders and explores the extent that achievement gaps in math widen for high performing African American and Latino students and their high performing White and Asian peers during high school. Using nationally representative data from the High School Longitudinal…

ARRONAX, a high-energy and high-intensity cyclotron for nuclear medicine.

PubMed

Haddad, Ferid; Ferrer, Ludovic; Guertin, Arnaud; Carlier, Thomas; Michel, Nathalie; Barbet, Jacques; Chatal, Jean-François

2008-07-01

This study was aimed at establishing a list of radionuclides of interest for nuclear medicine that can be produced in a high-intensity and high-energy cyclotron. We have considered both therapeutic and positron emission tomography radionuclides that can be produced using a high-energy and a high-intensity cyclotron such as ARRONAX, which will be operating in Nantes (France) by the end of 2008. Novel radionuclides or radionuclides of current limited availability have been selected according to the following criteria: emission of positrons, low-energy beta or alpha particles, stable or short half-life daughters, half-life between 3 h and 10 days or generator-produced, favourable dosimetry, production from stable isotopes with reasonable cross sections. Three radionuclides appear well suited to targeted radionuclide therapy using beta ((67)Cu, (47)Sc) or alpha ((211)At) particles. Positron emitters allowing dosimetry studies prior to radionuclide therapy ((64)Cu, (124)I, (44)Sc), or that can be generator-produced ((82)Rb, (68)Ga) or providing the opportunity of a new imaging modality ((44)Sc) are considered to have a great interest at short term whereas (86)Y, (52)Fe, (55)Co, (76)Br or (89)Zr are considered to have a potential interest at middle term. Several radionuclides not currently used in routine nuclear medicine or not available in sufficient amount for clinical research have been selected for future production. High-energy, high-intensity cyclotrons are necessary to produce some of the selected radionuclides and make possible future clinical developments in nuclear medicine. Associated with appropriate carriers, these radionuclides will respond to a maximum of unmet clinical needs.

Evaluating High School IT

ERIC Educational Resources Information Center

Thompson, Brett A.

2004-01-01

Since its inception in 1997, Cisco's curriculum has entered thousands of high schools across the U.S. and around the world for two reasons: (1) Cisco has a large portion of the computer networking market, and thus has the resources for and interest in developing high school academies; and (2) high school curriculum development teams recognize the…

A Call to Action: Transforming High School for All Youth. National High School Alliance

ERIC Educational Resources Information Center

Institute for Educational Leadership (NJ1), 2005

2005-01-01

This paper identifies six core principles and recommends strategies that will foster high academic achievement, close the achievement gap, and promote civic and personal growth among all high-school-age youth in the high schools and communities. At the center of the framework is the Alliance's belief that the purpose of high school is to ensure…

Principals' Perceptions of Professional Development in High- and Low-Performing High-Poverty Schools

ERIC Educational Resources Information Center

Moore, Sheila; Kochan, Frances

2013-01-01

This is the second part of a two-part study examining issues related to professional development in high-poverty schools. The findings from the initial study indicated that principals in high-poverty, high-performing schools perceived higher levels of implementation of quality professional development standards in their schools than did principals…

Recommended high-tank temperatures for maintenance of high-tank backup support, Revision 3

DOE Office of Scientific and Technical Information (OSTI.GOV)

Greager, O.H.

1964-05-20

Purpose of this note is to recommend revised curves for the high-tank temperature required to maintain adequate high-tank backup support at the six small reactors. Compliance with the conditions shown on these curves will ensure adequate high-tank flow rates following the simultaneous loss of electric and steam power.

Simple method enabling pulse on command from high power, high frequency lasers

NASA Astrophysics Data System (ADS)

Baer, David J.; Marshall, Graham D.; Coutts, David W.; Mildren, Richard P.; Withford, Michael J.

2006-09-01

A method for addressing individual laser pulses in high repetition frequency systems using an intracavity optical chopper and novel electronic timing system is reported. This "pulse on command" capability is shown to enable free running and both subharmonic pulse rate and burst mode operation of a high power, high pulse frequency copper vapor laser while maintaining a fixed output pulse energy. We demonstrate that this technique can be used to improve feature finish when laser micromachining metal.

Availability of High School Extracurricular Sports Programs and High-Risk Behaviors

ERIC Educational Resources Information Center

Cohen, Deborah A.; Taylor, Stephanie L.; Zonta, Michela; Vestal, Katherine D.; Schuster, Mark A.

2007-01-01

Background: The Surgeon General has called for an expansion of school-based extracurricular sports programs to address the obesity epidemic. However, little is known about the availability of and participation in high school extracurricular sports and how participation in these sports is related to high-risk behaviors. Methods: We surveyed Los…

Beyond High Stakes Testing: Rural High School Students and Their Yearbooks

ERIC Educational Resources Information Center

Hoffman, Lynn M.

2005-01-01

I conducted surveys, focus group interviews, and analyzed the yearbooks of fifty four yearbook students from five rural high schools to investigate students' process of yearbook construction and to determine what was meaningful and memorable to them throughout their high school experience. Chang's (1992) construct of an adolescent ethos, including…

Highly-Parallel, Highly-Compact Computing Structures Implemented in Nanotechnology

NASA Technical Reports Server (NTRS)

Crawley, D. G.; Duff, M. J. B.; Fountain, T. J.; Moffat, C. D.; Tomlinson, C. D.

1995-01-01

In this paper, we describe work in which we are evaluating how the evolving properties of nano-electronic devices could best be utilized in highly parallel computing structures. Because of their combination of high performance, low power, and extreme compactness, such structures would have obvious applications in spaceborne environments, both for general mission control and for on-board data analysis. However, the anticipated properties of nano-devices mean that the optimum architecture for such systems is by no means certain. Candidates include single instruction multiple datastream (SIMD) arrays, neural networks, and multiple instruction multiple datastream (MIMD) assemblies.

High specific energy, high capacity nickel-hydrogen cell design

NASA Technical Reports Server (NTRS)

Wheeler, James R.

1993-01-01

A 3.5 inch rabbit-ear-terminal nickel-hydrogen cell has been designed and tested to deliver high capacity at a C/1.5 discharge rate. Its specific energy yield of 60.6 wh/kg is believed to be the highest yet achieved in a slurry-process nickel-hydrogen cell, and its 10 C capacity of 113.9 AH the highest capacity yet made at a discharge rate this high in the 3.5 inch diameter size. The cell also demonstrated a pulse capability of 180 amps for 20 seconds. Specific cell parameters, performance, and future test plans are described.

High-Speed, High-Temperature Finger Seal Test Evaluated

NASA Technical Reports Server (NTRS)

Proctor, Margaret P.

2003-01-01

A finger seal, designed and fabricated by Honeywell Engines, Systems and Services, was tested at the NASA Glenn Research Center at surface speeds up to 1200 ft/s, air temperatures up to 1200 F, and pressures across the seal of 75 psid. These are the first test results obtained with NASA s new High-Temperature, High-Speed Turbine Seal Test Rig (see the photograph). The finger seal is an innovative design recently patented by AlliedSignal Engines, which has demonstrated considerably lower leakage than commonly used labyrinth seals and is considerably cheaper than brush seals. The cost to produce finger seals is estimated to be about half of the cost to produce brush seals. Replacing labyrinth seals with fingers seals at locations that have high-pressure drops in gas turbine engines, typically main engine and thrust seals, can reduce air leakage at each location by 50 percent or more. This directly results in a 0.7- to 1.4-percent reduction in specific fuel consumption and a 0.35- to 0.7-percent reduction in direct operating costs . Because the finger seal is a contacting seal, this testing was conducted to address concerns about its heat generation and life capability at the higher speeds and temperatures required for advanced engines. The test results showed that the seal leakage and wear performance are acceptable for advanced engines.

High School Oceanography.

ERIC Educational Resources Information Center

Falmouth Public Schools, MA.

This book is a compilation of a series of papers designed to aid high school teachers in organizing a course in oceanography for high school students. It consists of twelve papers, with references, covering each of the following: (1) Introduction to Oceanography, (2) Geology of the Ocean, (3) The Continental Shelves, (4) Physical Properties of Sea…

Fixing High Schools

ERIC Educational Resources Information Center

Perkins-Gough, Deborah

2005-01-01

Reports from national education organizations in the US indicate the sorry state of high schools in the country that are accused of failing to adequately prepare their graduates for college or for the workforce, highlighting what is a serious problem in light of the troubled state of the US economy. The need to improve high schools is urgent and…

High-power-density, high-energy-density fluorinated graphene for primary lithium batteries

NASA Astrophysics Data System (ADS)

Zhong, Guiming; Chen, Huixin; Huang, Xingkang; Yue, Hongjun; Lu, Canzhong

2018-03-01

Li/CFx is one of the highest-energy-density primary batteries; however, poor rate capability hinders its practical applications in high-power devices. Here we report a preparation of fluorinated graphene (GFx) with superior performance through a direct gas fluorination. We find that the so-called “semi-ionic” C-F bond content in all C-F bonds presents a more critical impact on rate performance of the GFx in comparison with sp2 C content in the GFx, morphology, structure, and specific surface area of the materials. The rate capability remains excellent before the semi-ionic C-F bond proportion in the GFx decreases. Thus, by optimizing semi-ionic C-F content in our GFx, we obtain the optimal x of 0.8, with which the GF0.8 exhibits a very high energy density of 1073 Wh kg-1 and an excellent power density of 21460 W kg-1 at a high current density of 10 A g-1. More importantly, our approach opens a new avenue to obtain fluorinated carbon with high energy densities without compromising high power densities.

Integrated and comparative proteomics of high-oil and high-protein soybean seeds.

PubMed

Xu, Xiu Ping; Liu, Hui; Tian, Lihong; Dong, Xiang Bai; Shen, Shi Hua; Qu, Le Qing

2015-04-01

We analysed the global protein expression in seeds of a high-oil soybean cultivar (Jiyu 73, JY73) by proteomics. More than 700 protein spots were detected and 363 protein spots were successfully identified. Comparison of the protein profile of JY73 with that of a high-protein cultivar (Zhonghuang 13, ZH13) revealed 40 differentially expressed proteins, including oil synthesis, redox/stress, hydrolysis and storage-related proteins. All redox/stress proteins were less or not expressed in JY73, whereas the expression of the major storage proteins, nitrogen and carbon metabolism-related proteins was higher in ZH13. Biochemical analysis of JY73 revealed that it was in a low oxidation state, with a high content of polyunsaturated fatty acids and vitamin E. Vitamin E was more active than antioxidant enzymes and protected the soybean seed in a lower oxidation state. The characteristics of high oil and high protein in soybean, we revealed, might provide a reference for soybean nutrition and soybean breeding. Copyright © 2014 Elsevier Ltd. All rights reserved.

Flexible asymmetric supercapacitors with high energy and high power density in aqueous electrolytes.

PubMed

Cheng, Yingwen; Zhang, Hongbo; Lu, Songtao; Varanasi, Chakrapani V; Liu, Jie

2013-02-07

Supercapacitors with both high energy and high power densities are critical for many practical applications. In this paper, we discuss the design and demonstrate the fabrication of flexible asymmetric supercapacitors based on nanocomposite electrodes of MnO(2), activated carbon, carbon nanotubes and graphene. The combined unique properties of each of these components enable highly flexible and mechanically strong films that can serve as electrodes directly without using any current collectors or binders. Using these flexible electrodes and a roll-up approach, asymmetric supercapacitors with 2 V working voltage were successfully fabricated. The fabricated device showed excellent rate capability, with 78% of the original capacitance retained when the scan rate was increased from 2 mV s(-1) to 500 mV s(-1). Owing to the unique composite structure, these supercapacitors were able to deliver high energy density (24 W h kg(-1)) under high power density (7.8 kW kg(-1)) conditions. These features could enable supercapacitor based energy storage systems to be very attractive for a variety of critical applications, such as the power sources in hybrid electric vehicles and the back-up powers for wind and solar energy, where both high energy density and high power density are required.

High-pressure, High-temperature Deformation Experiment Using the New Generation Griggs-type Apparatus

PubMed Central

Précigout, Jacques; Stünitz, Holger; Pinquier, Yves; Champallier, Rémi; Schubnel, Alexandre

2018-01-01

In order to address geological processes at great depths, rock deformation should ideally be tested at high pressure (> 0.5 GPa) and high temperature (> 300 °C). However, because of the low stress resolution of current solid-pressure-medium apparatuses, high-resolution measurements are today restricted to low-pressure deformation experiments in the gas-pressure-medium apparatus. A new generation of solid-medium piston-cylinder ("Griggs-type") apparatus is here described. Able to perform high-pressure deformation experiments up to 5 GPa and designed to adapt an internal load cell, such a new apparatus offers the potential to establish a technological basis for high-pressure rheology. This paper provides video-based detailed documentation of the procedure (using the "conventional" solid-salt assembly) to perform high-pressure, high-temperature experiments with the newly designed Griggs-type apparatus. A representative result of a Carrara marble sample deformed at 700 °C, 1.5 GPa and 10-5 s-1 with the new press is also given. The related stress-time curve illustrates all steps of a Griggs-type experiment, from increasing pressure and temperature to sample quenching when deformation is stopped. Together with future developments, the critical steps and limitations of the Griggs apparatus are then discussed. PMID:29683444

High mortality in diabetic recipients of high KDPI deceased donor kidneys.

PubMed

Pelletier, Ronald P; Pesavento, Todd E; Rajab, Amer; Henry, Mitchell L

2016-08-01

Deceased donor (DD) kidney quality is determined by calculating the Kidney Donor Profile Index (KDPI). Optimizing high KDPI (≥85%) DD transplant outcome is challenging. This retrospective study was performed to review our high KDPI DD transplant results to identify clinical practices that can improve future outcomes. We retrospectively calculated the KDPI for 895 DD kidney recipients transplanted between 1/2002 and 11/2013. Age, race, body mass index (BMI), retransplantation, gender, diabetes (DM), dialysis time, and preexisting coronary artery disease (CAD) (previous myocardial infarction (MI), coronary artery bypass (CABG), or stenting) were determined for all recipients. About 29.7% (266/895) of transplants were from donors with a KDPI ≥85%. By Cox regression older age, diabetes, female gender, and dialysis time >4 years correlated with shorter patient survival time. Diabetics with CAD who received a high KDPI donor kidney had a significantly increased risk of death (HR 4.33 (CI 1.82-10.30), P=.001) compared to low KDPI kidney recipients. The Kaplan-Meier survival curve for diabetic recipients of high KDPI kidneys was significantly worse if they had preexisting CAD (P<.001 by log-rank test). Patient survival using high KDPI donor kidneys may be improved by avoiding diabetic candidates with preexisting CAD. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Pedagogical Stances of High School ESL Teachers: "Huelgas" in High School ESL Classrooms

ERIC Educational Resources Information Center

del Carmen Salazar, Maria

2010-01-01

This article presents a qualitative case study of the pedagogical stances of high school English as a Second Language (ESL) teachers, and the subsequent responses of resistance or conformity by their English Language Learners (ELLs). The participants include three high school ESL teachers and 60 high school ESL students of Mexican origin. Findings…

Manga High: Literacy, Identity, and Coming of Age in an Urban High School

ERIC Educational Resources Information Center

Bitz, Michael

2009-01-01

Based on a four-year study, "Manga High" explores the convergence of literacy, creativity, social development, and personal identity in one of New York City's largest high schools. Since 2004, students at Martin Luther King, Jr., High School in Manhattan have been creating manga--Japanese comic books. They write the stories, design the…

Diagnostic accuracy of high-definition CT coronary angiography in high-risk patients.

PubMed

Iyengar, S S; Morgan-Hughes, G; Ukoumunne, O; Clayton, B; Davies, E J; Nikolaou, V; Hyde, C J; Shore, A C; Roobottom, C A

2016-02-01

To assess the diagnostic accuracy of computed tomography coronary angiography (CTCA) using a combination of high-definition CT (HD-CTCA) and high level of reader experience, with invasive coronary angiography (ICA) as the reference standard, in high-risk patients for the investigation of coronary artery disease (CAD). Three hundred high-risk patients underwent HD-CTCA and ICA. Independent experts evaluated the images for the presence of significant CAD, defined primarily as the presence of moderate (≥ 50%) stenosis and secondarily as the presence of severe (≥ 70%) stenosis in at least one coronary segment, in a blinded fashion. HD-CTCA was compared to ICA as the reference standard. No patients were excluded. Two hundred and six patients (69%) had moderate and 178 (59%) had severe stenosis in at least one vessel at ICA. The sensitivity, specificity, positive predictive value, and negative predictive value were 97.1%, 97.9%, 99% and 93.9% for moderate stenosis, and 98.9%, 93.4%, 95.7% and 98.3%, for severe stenosis, on a per-patient basis. The combination of HD-CTCA and experienced readers applied to a high-risk population, results in high diagnostic accuracy comparable to ICA. Modern generation CT systems in experienced hands might be considered for an expanded role. Copyright © 2015 The Royal College of Radiologists. Published by Elsevier Ltd. All rights reserved.

Scratch-resistant, highly conductive, and high-strength carbon nanotube-based composite yarns.

PubMed

Liu, Kai; Sun, Yinghui; Lin, Xiaoyang; Zhou, Ruifeng; Wang, Jiaping; Fan, Shoushan; Jiang, Kaili

2010-10-26

High-strength and conductive carbon nanotube (CNT) yarns are very attractive in many potential applications. However, there is a difficulty when simultaneously enhancing the strength and conductivity of CNT yarns. Adding some polymers into CNT yarns to enhance their strength will decrease their conductivity, while treating them in acid or coating them with metal nanoparticles to enhance their conductivity will reduce their strength. To overcome this difficulty, here we report a method to make high-strength and highly conductive CNT-based composite yarns by using a continuous superaligned CNT (SACNT) yarn as a conductive framework and then inserting polyvinyl alcohol (PVA) into the intertube spaces of the framework through PVA/dimethyl sulphoxide solution to enhance the strength of yarns. The as-produced CNT/PVA composite yarns possess very high tensile strengths up to 2.0 GPa and Young's moduli more than 120 GPa, much higher than those of the CNT/PVA yarns reported. The electric conductivity of as-produced composite yarns is as high as 9.2 × 10(4) S/m, comparable to HNO(3)-treated or Au nanoparticle-coated CNT yarns. These composite yarns are flexible, lightweight, scratch-resistant, very stable in the lab environment, and resistant to extremely humid ambient and as a result can be woven into high-strength and heatable fabrics, showing potential applications in flexible heaters, bullet-proof vests, radiation protection suits, and spacesuits.

Switch contact device for interrupting high current, high voltage, AC and DC circuits

DOEpatents

Via, Lester C.; Witherspoon, F. Douglas; Ryan, John M.

2005-01-04

A high voltage switch contact structure capable of interrupting high voltage, high current AC and DC circuits. The contact structure confines the arc created when contacts open to the thin area between two insulating surfaces in intimate contact. This forces the arc into the shape of a thin sheet which loses heat energy far more rapidly than an arc column having a circular cross-section. These high heat losses require a dramatic increase in the voltage required to maintain the arc, thus extinguishing it when the required voltage exceeds the available voltage. The arc extinguishing process with this invention is not dependent on the occurrence of a current zero crossing and, consequently, is capable of rapidly interrupting both AC and DC circuits. The contact structure achieves its high performance without the use of sulfur hexafluoride.

Female Leadership at High-Poverty, High-Performing Schools: Four Case Studies

ERIC Educational Resources Information Center

Reynolds, Shirley Ann

2009-01-01

This mixed methods study examined the leadership abilities of four African American female principals in an urban setting. The purpose of the mixed methods study was to observe, describe and analyze how the principals have been effective leaders in their respective high-poverty, high-performing elementary schools (K-5). The qualitative methodology…

Early College High Schools

ERIC Educational Resources Information Center

Dessoff, Alan

2011-01-01

For at-risk students who stand little chance of going to college, or even finishing high school, a growing number of districts have found a solution: Give them an early start in college while they still are in high school. The early college high school (ECHS) movement that began with funding from the Bill and Melinda Gates Foundation 10 years ago…

Effect of high fluoride and high fat on serum lipid levels and oxidative stress in rabbits.

PubMed

Sun, Liyan; Gao, Yanhui; Zhang, Wei; Liu, Hui; Sun, Dianjun

2014-11-01

The purpose of this study was to explore the effects of high fluoride and high fat on triglyceride (TG), total cholesterol (TC), high density lipoprotein cholesterol (HDL-C), low density lipoprotein cholesterol (LDL-C), total antioxidant capacity (T-AOC), lipid peroxide (LPO) and malondialdehyde (MDA) in rabbits. A factorial experimental design was used, with two factors (fluoride and fat) and three levels. Seventy-two male rabbits were randomly assigned into nine groups according to initial weight and serum lipid levels. The rabbits were fed with basic feed, moderate fat feed or high fat feed and drank tap water, fluoridated water at levels of 50 and 100mgfluorion/L freely. Biological materials were collected after 5 months, and serum lipid, T-AOC, LPO, and MDA levels were then measured. Using these data, the separate and interactive effects of high fluoride and high fat were analyzed. High fluoride and high fat both increased serum levels of TC, HDL-C and LDL-C significantly (P<0.05), and there was also a synergistic effect between high fluoride and high fat (P<0.05). High fluoride and high fat had different effects on TG levels: high fat significantly increased TG levels (P<0.01) whereas high fluoride had nothing to do with TG levels (P>0.05). High fat significantly elevated LPO and MDA levels and lowered T-AOC levels in serum (P<0.05). Similarly, high fluoride significantly increased LPO and MDA levels in serum (P<0.05). However, there was no interactive effect between high fat and high fluoride on these indexes. In summary, high fluoride and high fat increased serum TC and LDL-C levels individually and synergistically, and this would cause and aggravate hypercholesterolemia in rabbits. At the same time, high fluoride and high fat both made the accumulation of product of oxidative stress in experimental animals. Copyright © 2014 Elsevier B.V. All rights reserved.

Re-Conceptualizing Extra Help for High School Students in a High Standards Era

ERIC Educational Resources Information Center

Balfanz, Robert; McPartland, James; Shaw, Alta

2002-01-01

One of the aims of the standards and accountability movement is to make intellectually demanding course work in high school the norm. Significant progress has been made towards this goal. Expecting all students to engage in and succeed with challenging work in high school, however, places on high schools demands they have not been historically…

Effects of High Mean Stress on High-cycle Fatigue Behavior of PWA 1480

NASA Technical Reports Server (NTRS)

Majumdar, S.; Antolovich, S. D.; Milligan, W. W.

1985-01-01

PWA 1480 is a potential candidate material for use in the high-pressure fuel turbine blade of the space shuttle main engine. As an engine material it will be subjected to high-cycle fatigue loading superimposed on a high mean stress due to combined centrifugal and thermal loadings. The present paper describes the results obtained in an ongoing program at the Argonne National Laboratory, sponsored by NASA Lewis, to determine the effects of a high mean stress on the high-cycle fatigue behavior of this material. Straight-gauge high-cycle fatigue specimens, 0.2 inch in diameter and with the specimen axis in the 001 direction, were supplied by NASA Lewis. The nominal room temperature yield and ultimate strength of the material were 146 and 154 ksi, respectively. Each specimen was polished with 1-micron diamond paste prior to testing. However, the surface of each specimen contained many pores, some of which were as large as 50 micron. In the initial tests, specimens were subjected to axial-strain-controlled cycles. However, very little cyclic plasticity was observed.

High efficiency upconversion nanophosphors for high-contrast bioimaging

NASA Astrophysics Data System (ADS)

Alkahtani, Masfer H.; Alghannam, Fahad S.; Sanchez, Carlos; Gomes, Carmen L.; Liang, Hong; Hemmer, Philip R.

2016-12-01

Upconversion nanoparticles (UCNPs) are of interest because they allow suppression of tissue autofluorescence and are therefore visible deep inside biological tissue. Compared to upconversion dyes, UCNPs have a lower pump intensity threshold, better photostability, and less toxicity. Recently, YVO4: Er+3, Yb+3 nanoparticles were shown to exhibit strong up-conversion luminescence with a relatively low 10 kW cm-2 excitation intensity even in water, which makes them excellent bio-imaging candidates. Herein, we investigate their use as internal probes in insects by injecting YVO4 : Er+3, Yb+3 nanoparticles into fire ants as a biological model, and obtain 2D optical images with 980 nm illumination. High-contrast images with high signal-to-noise ratio are observed by detecting the up-conversion fluorescence as the excitation laser is scanned.

High-Speed, High-Temperature Finger Seal Test Results

NASA Technical Reports Server (NTRS)

Proctor, Margaret P.; Kumar, Arun; Delgado, Irebert R.

2002-01-01

Finger seals have significantly lower leakage rates than conventional labyrinth seals used in gas turbine engines and are expected to decrease specific fuel consumption by over 1 percent and to decrease direct operating cost by over 0.5 percent. Their compliant design accommodates shaft growth and motion due to thermal and dynamic loads with minimal wear. The cost to fabricate these finger seals is estimated to be about half the cost to fabricate brush seals. A finger seal has been tested in NASA's High Temperature, High Speed Turbine Seal Test Rig at operating conditions up to 1200 F, 1200 ft/s, and 75 psid. Static, performance and endurance test results are presented. While seal leakage and wear performance are acceptable, further design improvements are needed to reduce the seal power loss.

Structural application of high strength, high temperature ceramics

NASA Technical Reports Server (NTRS)

Hall, W. B.

1982-01-01

The operation of rocket engine turbine pumps is limited by the temperature restrictions of metallic components used in the systems. Mechanical strength and stability of these metallic components decrease drastically at elevated temperatures. Ceramic materials that retain high strength at high temperatures appear to be a feasible alternate material for use in the hot end of the turbopumps. This project identified and defined the processing parameters that affected the properties of Si3N4, one of candidate ceramic materials. Apparatus was assembled and put into operation to hot press Si3N4 powders into bulk material for in house evaluation. A work statement was completed to seek outside contract services to design, manufacture, and evaluate Si3N4 components in the service environments that exists in SSME turbopumps.

High sensitivity, wide coverage, and high-resolution NIR non-cryogenic spectrograph, WINERED

NASA Astrophysics Data System (ADS)

Ikeda, Yuji; Kobayashi, Naoto; Kondo, Sohei; Otsubo, Shogo; Hamano, Satoshi; Sameshima, Hiroaki; Yoshikawa, Tomoshiro; Fukue, Kei; Nakanishi, Kenshi; Kawanishi, Takafumi; Nakaoka, Tetsuya; Kinoshita, Masaomi; Kitano, Ayaka; Asano, Akira; Takenaka, Keiichi; Watase, Ayaka; Mito, Hiroyuki; Yasui, Chikako; Minami, Atsushi; Izumu, Natsuko; Yamamoto, Ryo; Mizumoto, Misaki; Arasaki, Takayuki; Arai, Akira; Matsunaga, Noriyuki; Kawakita, Hideyo

2016-08-01

Near-infrared (NIR) high-resolution spectroscopy is a fundamental observational method in astronomy. It provides significant information on the kinematics, the magnetic fields, and the chemical abundances, of astronomical objects embedded in or behind the highly extinctive clouds or at the cosmological distances. Scientific requirements have accelerated the development of the technology required for NIR high resolution spectrographs using 10 m telescopes. WINERED is a near-infrared (NIR) high-resolution spectrograph that is currently mounted on the 1.3 m Araki telescope of the Koyama Astronomical Observatory in Kyoto-Sangyo University, Japan, and has been successfully operated for three years. It covers a wide wavelength range from 0.90 to 1.35 μm (the z-, Y-, and J-bands) with a spectral resolution of R = 28,000 (Wide-mode) and R = 80,000 (Hires-Y and Hires-J modes). WINERED has three distinctive features: (i) optics with no cold stop, (ii) wide spectral coverage, and (iii) high sensitivity. The first feature, originating from the Joyce proposal, was first achieved by WINERED, with a short cutoff infrared array, cold baffles, and custom-made thermal blocking filters, and resulted in reducing the time for development, alignment, and maintenance, as well as the total cost. The second feature is realized with the spectral coverage of Δλ/λ 1/6 in a single exposure. This wide coverage is realized by a combination of a decent optical design with a cross-dispersed echelle and a large format array (2k x 2k HAWAII- 2RG). The Third feature, high sensitivity, is achieved via the high-throughput optics (>60 %) and the very low noise of the system. The major factors affecting the high throughput are the echelle grating and the VPH cross-disperser with high diffraction efficiencies of 83 % and 86 %, respectively, and the high QE of HAWAII-2RG (83 % at 1.23 μm). The readout noise of the electronics and the ambient thermal background radiation at longer wavelengths could be

Re-Conceptualizing Extra Help for High School Students in a High Standards Era.

ERIC Educational Resources Information Center

Balfanz, Robert; McPartland, James; Shaw, Alta

The push for higher academic standards has resulted in an increase in the numbers of high school students needing extra help. The need for extra help is most pervasive in high-poverty areas and most high school students need extra help not in traditional basic elementary skills but in reading, mathematics, and advanced reasoning skills. Most…

High-Voltage Lithium-Metal Batteries Enabled by Localized High-Concentration Electrolytes.

PubMed

Chen, Shuru; Zheng, Jianming; Mei, Donghai; Han, Kee Sung; Engelhard, Mark H; Zhao, Wengao; Xu, Wu; Liu, Jun; Zhang, Ji-Guang

2018-03-25

Rechargeable lithium-metal batteries (LMBs) are regarded as the "holy grail" of energy-storage systems, but the electrolytes that are highly stable with both a lithium-metal anode and high-voltage cathodes still remain a great challenge. Here a novel "localized high-concentration electrolyte" (HCE; 1.2 m lithium bis(fluorosulfonyl)imide in a mixture of dimethyl carbonate/bis(2,2,2-trifluoroethyl) ether (1:2 by mol)) is reported that enables dendrite-free cycling of lithium-metal anodes with high Coulombic efficiency (99.5%) and excellent capacity retention (>80% after 700 cycles) of Li||LiNi 1/3 Mn 1/3 Co 1/3 O 2 batteries. Unlike the HCEs reported before, the electrolyte reported in this work exhibits low concentration, low cost, low viscosity, improved conductivity, and good wettability that make LMBs closer to practical applications. The fundamental concept of "localized HCEs" developed in this work can also be applied to other battery systems, sensors, supercapacitors, and other electrochemical systems. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High Frequency High Spectral Resolution Focal Plane Arrays for AtLAST

NASA Astrophysics Data System (ADS)

Baryshev, Andrey

2018-01-01

Large collecting area single dish telescope such as ATLAST will be especially effective for medium (R 1000) and high (R 50000) spectral resolution observations. Large focal plane array is a natural solution to increase mapping speed. For medium resolution direct detectors with filter banks (KIDs) and or heterodyne technology can be employed. We will analyze performance limits of comparable KID and SIS focal plane array taking into account quantum limit and high background condition of terrestrial observing site. For large heterodyne focal plane arrays, a high current density AlN junctions open possibility of large instantaneous bandwidth >40%. This and possible multi frequency band FPSs presents a practical challenge for spatial sampling and scanning strategies. We will discuss phase array feeds as a possible solution, including a modular back-end system, which can be shared between KID and SIS based FPA. Finally we will discuss achievable sensitivities and pixel co unts for a high frequency (>500 GHz) FPAs and address main technical challenges: LO distribution, wire counts, bias line multiplexing, and monolithic vs. discrete mixer component integration.

High Touch in a High-Tech World

ERIC Educational Resources Information Center

Gibson, Cindy L.

2009-01-01

In a world of high tech and low touch, it is easy for public relations programs to stray from tried-and-true interpersonal strategies long associated with solid communication planning. New technologies allow communications professionals to quickly send e-mails and telephone calls to selected groups. Social media sites provide users immediate…

High temperature sensor

DOEpatents

Tokarz, Richard D.

1982-01-01

A high temperature sensor includes a pair of electrical conductors separated by a mass of electrical insulating material. The insulating material has a measurable resistivity within the sensor that changes in relation to the temperature of the insulating material within a high temperature range (1,000 to 2,000 K.). When required, the sensor can be encased within a ceramic protective coating.

Image Quality in High-resolution and High-cadence Solar Imaging

NASA Astrophysics Data System (ADS)

Denker, C.; Dineva, E.; Balthasar, H.; Verma, M.; Kuckein, C.; Diercke, A.; González Manrique, S. J.

2018-03-01

Broad-band imaging and even imaging with a moderate bandpass (about 1 nm) provides a photon-rich environment, where frame selection (lucky imaging) becomes a helpful tool in image restoration, allowing us to perform a cost-benefit analysis on how to design observing sequences for imaging with high spatial resolution in combination with real-time correction provided by an adaptive optics (AO) system. This study presents high-cadence (160 Hz) G-band and blue continuum image sequences obtained with the High-resolution Fast Imager (HiFI) at the 1.5-meter GREGOR solar telescope, where the speckle-masking technique is used to restore images with nearly diffraction-limited resolution. The HiFI employs two synchronized large-format and high-cadence sCMOS detectors. The median filter gradient similarity (MFGS) image-quality metric is applied, among others, to AO-corrected image sequences of a pore and a small sunspot observed on 2017 June 4 and 5. A small region of interest, which was selected for fast-imaging performance, covered these contrast-rich features and their neighborhood, which were part of Active Region NOAA 12661. Modifications of the MFGS algorithm uncover the field- and structure-dependency of this image-quality metric. However, MFGS still remains a good choice for determining image quality without a priori knowledge, which is an important characteristic when classifying the huge number of high-resolution images contained in data archives. In addition, this investigation demonstrates that a fast cadence and millisecond exposure times are still insufficient to reach the coherence time of daytime seeing. Nonetheless, the analysis shows that data acquisition rates exceeding 50 Hz are required to capture a substantial fraction of the best seeing moments, significantly boosting the performance of post-facto image restoration.

High-Order Dielectric Metasurfaces for High-Efficiency Polarization Beam Splitters and Optical Vortex Generators

NASA Astrophysics Data System (ADS)

Guo, Zhongyi; Zhu, Lie; Guo, Kai; Shen, Fei; Yin, Zhiping

2017-08-01

In this paper, a high-order dielectric metasurface based on silicon nanobrick array is proposed and investigated. By controlling the length and width of the nanobricks, the metasurfaces could supply two different incremental transmission phases for the X-linear-polarized (XLP) and Y-linear-polarized (YLP) light with extremely high efficiency over 88%. Based on the designed metasurface, two polarization beam splitters working in high-order diffraction modes have been designed successfully, which demonstrated a high transmitted efficiency. In addition, we have also designed two vortex-beam generators working in high-order diffraction modes to create vortex beams with the topological charges of 2 and 3. The employment of dielectric metasurfaces operating in high-order diffraction modes could pave the way for a variety of new ultra-efficient optical devices.

1997 NASA High-Speed Research Program Aerodynamic Performance Workshop. Volume 2; High Lift

NASA Technical Reports Server (NTRS)

Baize, Daniel G. (Editor)

1999-01-01

The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Aerodynamic Performance Workshop on February 25-28, 1997. The workshop was designed to bring together NASA and industry High-Speed Civil Transport (HSCT) Aerodynamic Performance technology development participants in areas of Configuration Aerodynamics (transonic and supersonic cruise drag, prediction and minimization), High-Lift, Flight Controls, Supersonic Laminar Flow Control, and Sonic Boom Prediction. The workshop objectives were to (1) report the progress and status of HSCT aerodynamic performance technology development; (2) disseminate this technology within the appropriate technical communities; and (3) promote synergy among the scientist and engineers working HSCT aerodynamics. In particular, single- and multi-point optimized HSCT configurations, HSCT high-lift system performance predictions, and HSCT Motion Simulator results were presented along with executives summaries for all the Aerodynamic Performance technology areas.

Rheological assessment of nanofluids at high pressure high temperature

NASA Astrophysics Data System (ADS)

Kanjirakat, Anoop; Sadr, Reza

2013-11-01

High pressure high temperature (HPHT) fluids are commonly encountered in industry, for example in cooling and/or lubrications applications. Nanofluids, engineered suspensions of nano-sized particles dispersed in a base fluid, have shown prospective as industrial cooling fluids due to their enhanced rheological and heat transfer properties. Nanofluids can be potentially utilized in oil industry for drilling fluids and for high pressure water jet cooling/lubrication in machining. In present work rheological characteristics of oil based nanofluids are investigated at HPHT condition. Nanofluids used in this study are prepared by dispersing commercially available SiO2 nanoparticles (~20 nm) in a mineral oil. The basefluid and nanofluids with two concentrations, namely 1%, and 2%, by volume, are considered in this investigation. The rheological characteristics of base fluid and the nanofluids are measured using an industrial HPHT viscometer. Viscosity values of the nanofluids are measured at pressures of 100 kPa to 42 MPa and temperatures ranging from 25°C to 140°C. The viscosity values of both nanofluids as well as basefluid are observed to have increased with the increase in pressure. Funded by Qatar National Research Fund (NPRP 08-574-2-239).

No More 1s: High Expectations Can Lead to High Achievement

ERIC Educational Resources Information Center

Cervone, Laureen; DiMartino, Lisa; Kerr, Kris

2010-01-01

The school district in Middletown, New York, in the state's Orange County, today serves close to 7,000 students in four elementary schools, two middle schools, and one high school. The district is classified by the state in the highest of three Need-to-Resource-Capacity groups, an urban or suburban school district with high student needs in…

Ceramic-to-Metal Joining for High Temperature, High Pressure Heat Exchangers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mako, Frederick; Mako III, Frederick

2016-12-05

Designed and tested silicon carbide to metal joining and silicon carbide joining technology under high temperature and high pressure conditions. Determined that the joints maintained integrity and remained helium gas tight. These joined parts have been tested for mechanical strength, fracture toughness and hermeticity. A component testing chamber was designed and built and used for testing the joint integrity.

Characterization and Fabrication of High k dielectric-High Mobility Channel Transistors

NASA Astrophysics Data System (ADS)

Sun, Xiao

As the conventional scaling of Si-based MOSFETs would bring negligible or even negative merits for IC's beyond the 7-nm CMOS technology node, many perceive the use of high-mobility channels to be one of the most likely principle changes, in order to achieve higher performance and lower power. However, interface and oxide traps have become a major obstacle for high-mobility semiconductors (such as Ge, InGaAs, GaSb, GaN...) to replace Si CMOS technology. In this thesis, the distinct properties of the traps in the high-k dielectric/high-mobility substrate system is discussed, as well as the challenges to characterize and passivate them. By modifying certain conventional gate admittance methods, both the fast and slow traps in Ge MOS gate stacks is investigated. In addition, a novel ac-transconductance method originated at Yale is introduced and demonstrated with several advanced transistors provided by collaborating groups, such as ultra-thin-body & box SO1 MOSFETs (CEA-LETI), InGaAs MOSFETs (IMEC, UT Austin, Purdue), and GaN MOS-HEMT (MIT). By use of the aforementioned characterization techniques, several effective passivation techniques on high mobility substrates (Ge, InGaAs, GaSb, GeSn, etc.) are evaluated, including a novel Ba sub-monolayer passivation of Ge surface. The key factors that need to be considered in passivating high mobility substrates are revealed. The techniques that we have established for characterizing traps in advanced field-effect transistors, as well as the knowledge gained about these traps by the use of these techniques, have been applied to the study of ionizing radiation effects in high-mobility-channel transistors, because it is very important to understand such effects as these devices are likely to be exposed to radiation-harsh environments, such as in outer space, nuclear plants, and during X-ray or UHV lithography. In this thesis, the total ionizing dose (TD) radiation effects of InGaAs-based MOSFETs and GaN-based MOS-HEMT are

High-sensitivity temperature sensor based on highly-birefringent microfiber

NASA Astrophysics Data System (ADS)

Sun, Li-Peng; Li, Jie; Jin, Long; Gao, Shuai; Tian, Zhuang; Ran, Yang; Guan, Bai-Ou

2013-09-01

We demonstrate an ultrasensitive temperature sensor by sealing a highly-birefringent microfiber into an alcoholinfiltrated copper capillary. With a Sagnac loop configuration, the interferometric spectrum is strongly dependent on the external refractive index (RI) with sensitivity of 36800nm/RIU around RI=1.356. As mainly derived from the ultrahigh RI sensitivity, the temperature response can reach as high as -14.72 nm/°C in the range of 30.9-36.9 °C. The measured response time is ~8s, as determined by the heat-conducting characteristic of the device and the diameter of the copper capillary. Our sensor is featured with low cost, easy fabrication and robustness.

Report on High School Characteristic Index Study at John Marshall High School - 1970.

ERIC Educational Resources Information Center

Newman, Wilfred

The High School Characteristic Index (H.S.C.I.) was employed at a high school in Rochester to measure students' perceptions, as well as teachers' ability to predict students' perceptions, after black-white violence occurred in May, 1970. The 1970 results were compared with 1966 results of the H.S.C.I. at the same high school when a different…

High-speed high-stress ring shear tests on granular sods and clayey soils

Treesearch

Hiroshi Fukuoka; Kyoji Sassa

1991-01-01

The purposes of this study is to obtain exact knowledge of the influences on friction angle during shear by shearing speeds. Ring shear tests on sandy and clayey materials have been carried out with a newly developed High-speed High-Stress Ring Shear Apparatus to examine if there are some changes in the frictional behaviors of these materials at high shearing speeds of...

Treatment Protocol for High Velocity/High Energy Gunshot Injuries to the Face

PubMed Central

Peled, Micha; Leiser, Yoav; Emodi, Omri; Krausz, Amir

2011-01-01

Major causes of facial combat injuries include blasts, high-velocity/high-energy missiles, and low-velocity missiles. High-velocity bullets fired from assault rifles encompass special ballistic properties, creating a transient cavitation space with a small entrance wound and a much larger exit wound. There is no dispute regarding the fact that primary emergency treatment of ballistic injuries to the face commences in accordance with the current advanced trauma life support (ATLS) recommendations; the main areas in which disputes do exist concern the question of the timing, sequence, and modes of surgical treatment. The aim of the present study is to present the treatment outcome of high-velocity/high-energy gunshot injuries to the face, using a protocol based on the experience of a single level I trauma center. A group of 23 injured combat soldiers who sustained bullet and shrapnel injuries to the maxillofacial region during a 3-week regional military conflict were evaluated in this study. Nine patients met the inclusion criteria (high-velocity/high-energy injuries) and were included in the study. According to our protocol, upon arrival patients underwent endotracheal intubation and were hemodynamically stabilized in the shock-trauma unit and underwent total-body computed tomography with 3-D reconstruction of the head and neck and computed tomography angiography. All patients underwent maxillofacial surgery upon the day of arrival according to the protocol we present. In view of our treatment outcomes, results, and low complication rates, we conclude that strict adherence to a well-founded and structured treatment protocol based on clinical experience is mandatory in providing efficient, appropriate, and successful treatment to a relatively large group of patients who sustain various degrees of maxillofacial injuries during a short period of time. PMID:23449809

Single-pass high harmonic generation at high repetition rate and photon flux

NASA Astrophysics Data System (ADS)

Hädrich, Steffen; Rothhardt, Jan; Krebs, Manuel; Demmler, Stefan; Klenke, Arno; Tünnermann, Andreas; Limpert, Jens

2016-09-01

Sources of short wavelength radiation with femtosecond to attosecond pulse durations, such as synchrotrons or free electron lasers, have already made possible numerous, and will facilitate more, seminal studies aimed at understanding atomic and molecular processes on fundamental length and time scales. Table-top sources of coherent extreme ultraviolet to soft x-ray radiation enabled by high harmonic generation (HHG) of ultrashort pulse lasers have also gained significant attention in the last few years due to their enormous potential for addressing a plethora of applications, therefore constituting a complementary source to large-scale facilities (synchrotrons and free electron lasers). Ti:sapphire based laser systems have been the workhorses for HHG for decades, but are limited in repetition rate and average power. On the other hand, it has been widely recognized that fostering applications in fields such as photoelectron spectroscopy and microscopy, coincidence detection, coherent diffractive imaging and frequency metrology requires a high repetition rate and high photon flux HHG sources. In this article we will review recent developments in realizing the demanding requirement of producing a high photon flux and repetition rate at the same time. Particular emphasis will be put on suitable ultrashort pulse and high average power lasers, which directly drive harmonic generation without the need for external enhancement cavities. To this end we describe two complementary schemes that have been successfully employed for high power fiber lasers, i.e. optical parametric chirped pulse amplifiers and nonlinear pulse compression. Moreover, the issue of phase-matching in tight focusing geometries will be discussed and connected to recent experiments. We will highlight the latest results in fiber laser driven high harmonic generation that currently produce the highest photon flux of all existing sources. In addition, we demonstrate the first promising applications and

Bridging the Silos of Service Delivery for High-Need, High-Cost Individuals.

PubMed

Sherry, Melissa; Wolff, Jennifer L; Ballreich, Jeromie; DuGoff, Eva; Davis, Karen; Anderson, Gerard

2016-12-01

Health care reform efforts that emphasize value have increased awareness of the importance of nonmedical factors in achieving better care, better health, and lower costs in the care of high-need, high-cost individuals. Programs that care for socioeconomically disadvantaged, high-need, high-cost individuals have achieved promising results in part by bridging traditional service delivery silos. This study examined 5 innovative community-oriented programs that are successfully coordinating medical and nonmedical services to identify factors that stimulate and sustain community-level collaboration and coordinated care across silos of health care, public health, and social services delivery. The authors constructed a conceptual framework depicting community health systems that highlights 4 foundational factors that facilitate community-oriented collaboration: flexible financing, shared leadership, shared data, and a strong shared vision of commitment toward delivery of person-centered care.

Diamond anvil cell for spectroscopic investigation of materials at high temperature, high pressure and shear

DOEpatents

Westerfield, Curtis L.; Morris, John S.; Agnew, Stephen F.

1997-01-01

Diamond anvil cell for spectroscopic investigation of materials at high temperature, high pressure and shear. A cell is described which, in combination with Fourier transform IR spectroscopy, permits the spectroscopic investigation of boundary layers under conditions of high temperature, high pressure and shear.

Progress in high duty cycle, highly efficient fiber coupled 940-nm pump modules for high-energy class solid-state lasers

NASA Astrophysics Data System (ADS)

Platz, R.; Frevert, C.; Eppich, B.; Rieprich, J.; Ginolas, A.; Kreutzmann, S.; Knigge, S.; Erbert, G.; Crump, P.

2018-03-01

Diode lasers pump sources for future high-energy-class laser systems based on Yb-doped solid state amplifiers must deliver high optical intensities, high conversion efficiency (ηE = > 50%) at high repetition rates (f = 100 Hz) and long pulse widths (τ = 0.5…2 ms). Over the last decade, a series of pump modules has been developed at the Ferdinand-BraunInstitut to address these needs. The latest modules use novel wide-aperture single emitter diode lasers in passively side cooled stacks, operate at τ = 1 ms, f = 100…200 Hz and deliver 5…6 kW optical output power from a fiber with 1.9 mm core diameter and NA of 0.22, for spatial brightness BΩ > 1 MW/cm2 sr. The performance to date and latest developments in these high brightness modules are summarized here with recent work focusing on extending operation to other pumping conditions, as needed for alternative solid state laser designs. Specifically, the electro-optic, spectral and beam propagation characteristics of the module and its components are studied as a function of τ for a fixed duty cycle DC = 10% for τ = 1...100 ms, and first data is shown for continuous wave operation. Clear potential is seen to fulfill more demanding specifications without design changes. For example, high power long-pulse operation is demonstrated, with a power of > 5 kW at τ = 100 ms. Higher brightness operation is also confirmed at DC = 10% and τ = 1 ms, with > 5 kW delivered in a beam with BΩ > 4 MW/cm2 sr.

High estradiol levels improve false memory rates and meta-memory in highly schizotypal women.

PubMed

Hodgetts, Sophie; Hausmann, Markus; Weis, Susanne

2015-10-30

Overconfidence in false memories is often found in patients with schizophrenia and healthy participants with high levels of schizotypy, indicating an impairment of meta-cognition within the memory domain. In general, cognitive control is suggested to be modulated by natural fluctuations in oestrogen. However, whether oestrogen exerts beneficial effects on meta-memory has not yet been investigated. The present study sought to provide evidence that high levels of schizotypy are associated with increased false memory rates and overconfidence in false memories, and that these processes may be modulated by natural differences in estradiol levels. Using the Deese-Roediger-McDermott paradigm, it was found that highly schizotypal participants with high estradiol produced significantly fewer false memories than those with low estradiol. No such difference was found within the low schizotypy participants. Highly schizotypal participants with high estradiol were also less confident in their false memories than those with low estradiol; low schizotypy participants with high estradiol were more confident. However, these differences only approached significance. These findings suggest that the beneficial effect of estradiol on memory and meta-memory observed in healthy participants is specific to highly schizotypal individuals and might be related to individual differences in baseline dopaminergic activity. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

High-Speed, High-Resolution Time-to-Digital Conversion

NASA Technical Reports Server (NTRS)

Katz, Richard; Kleyner, Igor; Garcia, Rafael

2013-01-01

This innovation is a series of time-tag pulses from a photomultiplier tube, featuring short time interval between pulses (e.g., 2.5 ns). Using the previous art, dead time between pulses is too long, or too much hardware is required, including a very-high-speed demultiplexer. A faster method is needed. The goal of this work is to provide circuits to time-tag pulses that arrive at a high rate using the hardwired logic in an FPGA - specifically the carry chain - to create what is (in effect) an analog delay line. High-speed pulses travel down the chain in a "wave." For instance, a pulse train has been demonstrated from a 1- GHz source reliably traveling down the carry chain. The size of the carry chain is over 10 ns in the time domain. Thus, multiple pulses will travel down the carry chain in a wave simultaneously. A register clocked by a low-skew clock takes a "snapshot" of the wave. Relatively simple logic can extract the pulses from the snapshot picture by detecting the transitions between logic states. The propagation delay of CMOS (complementary metal oxide semiconductor) logic circuits will differ and/or change as a result of temperature, voltage, age, radiation, and manufacturing variances. The time-to-digital conversion circuits can be calibrated with test signals, or the changes can be nulled by a separate on-die calibration channel, in a closed loop circuit.

High-temperature sensor

DOEpatents

Not Available

1981-01-29

A high temperature sensor is described which includes a pair of electrical conductors separated by a mass of electrical insulating material. The insulating material has a measurable resistivity within the sensor that changes in relation to the temperature of the insulating material within a high temperature range (1000 to 2000/sup 0/K). When required, the sensor can be encased within a ceramic protective coating.

High-Throughput/High-Content Screening Assays with Engineered Nanomaterials in ToxCast

EPA Science Inventory

High-throughput and high-content screens are attractive approaches for prioritizing nanomaterial hazards and informing targeted testing due to the impracticality of using traditional toxicological testing on the large numbers and varieties of nanomaterials. The ToxCast program a...

Ellagic acid attenuates high-carbohydrate, high-fat diet-induced metabolic syndrome in rats.

PubMed

Panchal, Sunil K; Ward, Leigh; Brown, Lindsay

2013-03-01

Fruits and nuts may prevent or reverse common human health conditions such as obesity, diabetes and hypertension; together, these conditions are referred to as metabolic syndrome, an increasing problem. This study has investigated the responses to ellagic acid, present in many fruits and nuts, in a diet-induced rat model of metabolic syndrome. Eight- to nine-week-old male Wistar rats were divided into four groups for 16-week feeding with cornstarch diet (C), cornstarch diet supplemented with ellagic acid (CE), high-carbohydrate, high-fat diet (H) and high-carbohydrate, high-fat diet supplemented with ellagic acid (HE). CE and HE rats were given 0.8 g/kg ellagic acid in food from week 8 to 16 only. At the end of 16 weeks, cardiovascular, hepatic and metabolic parameters along with protein levels of Nrf2, NF-κB and CPT1 in the heart and the liver were characterised. High-carbohydrate, high-fat diet-fed rats developed cardiovascular remodelling, impaired ventricular function, impaired glucose tolerance, non-alcoholic fatty liver disease with increased protein levels of NF-κB and decreased protein levels of Nrf2 and CPT1 in the heart and the liver. Ellagic acid attenuated these diet-induced symptoms of metabolic syndrome with normalisation of protein levels of Nrf2, NF-κB and CPT1. Ellagic acid derived from nuts and fruits such as raspberries and pomegranates may provide a useful dietary supplement to decrease the characteristic changes in metabolism and in cardiac and hepatic structure and function induced by a high-carbohydrate, high-fat diet by suppressing oxidative stress and inflammation.

High-Efficiency Silicon Carbide (SiC) Converters. Delivery Order 0001: Development of High-Temperature, High-Power, High-Efficiency, High-Voltage Converters Using Silicon Carbide

DTIC Science & Technology

2004-03-01

32 Silicon Dioxide as a Mask ......................................................... 34 Silicon Nitride as a Mask...phosphorous (P), and arsenic (As) for n-type material and aluminum (Al), boron (B), beryllium (Be), gallium (Ga), oxygen (O), and scandium (Sc) for...O2 in carbon tetrafluoride (CF4), nitrogen trifluoride (NF3), and sulfur hexafluoride (SF6) were observed because these gases produce high fluorine

A large high vacuum, high pumping speed space simulation chamber for electric propulsion

NASA Technical Reports Server (NTRS)

Grisnik, Stanley P.; Parkes, James E.

1994-01-01

Testing high power electric propulsion devices poses unique requirements on space simulation facilities. Very high pumping speeds are required to maintain high vacuum levels while handling large volumes of exhaust products. These pumping speeds are significantly higher than those available in most existing vacuum facilities. There is also a requirement for relatively large vacuum chamber dimensions to minimize facility wall/thruster plume interactions and to accommodate far field plume diagnostic measurements. A 4.57 m (15 ft) diameter by 19.2 m (63 ft) long vacuum chamber at NASA Lewis Research Center is described. The chamber utilizes oil diffusion pumps in combination with cryopanels to achieve high vacuum pumping speeds at high vacuum levels. The facility is computer controlled for all phases of operation from start-up, through testing, to shutdown. The computer control system increases the utilization of the facility and reduces the manpower requirements needed for facility operations.

77 FR 8758 - International Fisheries; Western and Central Pacific Fisheries for Highly Migratory Species; High...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-15

... Migratory Species; High Seas Transshipment Prohibitions AGENCY: National Marine Fisheries Service (NMFS...) to prohibit the transshipment of highly migratory species (HMS) on the high seas to or from certain... potential effects of a prohibition on high seas transshipments in the Convention Area. DATES: Comments must...

High coronal structure of high velocity solar wind stream sources

NASA Technical Reports Server (NTRS)

Nolte, J. T.; Krieger, A. S.; Roelof, E. C.; Gold, R. E.

1977-01-01

It is shown analytically that the transition from a high-speed stream source to the ambient coronal conditions is quite rapid in longitude in the high corona. This sharp eastern coronal boundary for the solar wind stream sources is strongly suggested by the solar wind 'dwells' which appear in plots of solar wind velocity against constant-radial-velocity-approximation source longitudes. The possibility of a systematic velocity-dependent effect in the constant-radial-velocity approximation, which would cause this boundary to appear sharper than it is, is investigated. A velocity-dependent interplanetary propagation effect or a velocity-dependent 'source altitude' are two possible sources of such a systematic effect. It is shown that, for at least some dwells, significant interplanetary effects are not likely. The variation of the Alfvenic critical radius in solar wind dwells is calculated, showing that the high-velocity stream originates from a significantly lower altitude than the ambient solar wind.

Unsupervised Learning Through Randomized Algorithms for High-Volume High-Velocity Data (ULTRA-HV).

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pinar, Ali; Kolda, Tamara G.; Carlberg, Kevin Thomas

Through long-term investments in computing, algorithms, facilities, and instrumentation, DOE is an established leader in massive-scale, high-fidelity simulations, as well as science-leading experimentation. In both cases, DOE is generating more data than it can analyze and the problem is intensifying quickly. The need for advanced algorithms that can automatically convert the abundance of data into a wealth of useful information by discovering hidden structures is well recognized. Such efforts however, are hindered by the massive volume of the data and its high velocity. Here, the challenge is developing unsupervised learning methods to discover hidden structure in high-volume, high-velocity data.

[Design of a high-voltage insulation testing system of X-ray high frequency generators].

PubMed

Huang, Yong; Mo, Guo-Ming; Wang, Yan; Wang, Hong-Zhi; Yu, Jie-Ying; Dai, Shu-Guang

2007-09-01

In this paper, we analyze the transformer of X-ray high-voltage high-frequency generators and, have designed and implemented a high-voltage insulation testing system for its oil tank using full-bridge series resonant soft switching PFM DC-DC converter.

Liquid lithium target as a high intensity, high energy neutron source

DOEpatents

Parkin, Don M.; Dudey, Norman D.

1976-01-01

This invention provides a target jet for charged particles. In one embodiment the charged particles are high energy deuterons that bombard the target jet to produce high intensity, high energy neutrons. To this end, deuterons in a vacuum container bombard an endlessly circulating, free-falling, sheet-shaped, copiously flowing, liquid lithium jet that gushes by gravity from a rectangular cross-section vent on the inside of the container means to form a moving web in contact with the inside wall of the vacuum container. The neutrons are produced via break-up of the beam in the target by stripping, spallation and compound nuclear reactions in which the projectiles (deuterons) interact with the target (Li) to produce excited nuclei, which then "boil off" or evaporate a neutron.

Method for the preparation of high surface area high permeability carbons

DOEpatents

Lagasse, R.R.; Schroeder, J.L.

1999-05-11

A method for preparing carbon materials having high surface area and high macropore volume to provide high permeability. These carbon materials are prepared by dissolving a carbonizable polymer precursor, in a solvent. The solution is cooled to form a gel. The solvent is extracted from the gel by employing a non-solvent for the polymer. The non-solvent is removed by critical point drying in CO{sub 2} at an elevated pressure and temperature or evaporation in a vacuum oven. The dried product is heated in an inert atmosphere in a first heating step to a first temperature and maintained there for a time sufficient to substantially cross-link the polymer material. The cross-linked polymer material is then carbonized in an inert atmosphere. 3 figs.

Method for the preparation of high surface area high permeability carbons

DOEpatents

Lagasse, Robert R.; Schroeder, John L.

1999-05-11

A method for preparing carbon materials having high surface area and high macropore volume to provide high permeability. These carbon materials are prepared by dissolving a carbonizable polymer precursor, in a solvent. The solution is cooled to form a gel. The solvent is extracted from the gel by employing a non-solvent for the polymer. The non-solvent is removed by critical point drying in CO.sub.2 at an elevated pressure and temperature or evaporation in a vacuum oven. The dried product is heated in an inert atmosphere in a first heating step to a first temperature and maintained there for a time sufficient to substantially cross-link the polymer material. The cross-linked polymer material is then carbonized in an inert atmosphere.

Diamond anvil cell for spectroscopic investigation of materials at high temperature, high pressure and shear

DOEpatents

Westerfield, C.L.; Morris, J.S.; Agnew, S.F.

1997-01-14

Diamond anvil cell is described for spectroscopic investigation of materials at high temperature, high pressure and shear. A cell is described which, in combination with Fourier transform IR spectroscopy, permits the spectroscopic investigation of boundary layers under conditions of high temperature, high pressure and shear. 4 figs.

Diurnal metabolic profiles after 14 d of an ad libitum high-starch, high-sucrose, or high-fat diet in normal-weight never-obese and postobese women.

PubMed

Raben, A; Holst, J J; Madsen, J; Astrup, A

2001-02-01

The influence of the amount and type of carbohydrates in the diet on risk factors for obesity, diabetes, and cardiovascular disease remains unclear. We investigated the effects of 2 low-fat diets (high-sucrose and high-starch) and a high-fat diet on glycemia, lipidemia, and hormonal responses in never-obese and postobese women. Eighteen normal-weight women (8 postobese and 10 never-obese) consumed 3 ad libitum diets (high-fat, high-starch, and high-sucrose) for 14 d each. On day 15, we measured fasting and postprandial glucose, lactate, insulin, triacylglycerol, nonesterified fatty acids (NEFA), glycerol, glucagon, glucose-dependent insulinotropic polypeptide, and glucagon-like peptide 1. The high-sucrose diet induced significantly lower total areas under the curve (AUCs) for glucose and NEFA and a significantly higher lactate AUC than did the high-fat and high-starch diets; there were no significant differences in the insulin AUCs. The triacylglycerol AUC was greater with the high-fat and high-sucrose diets than with the high-starch diet. Gastrointestinal hormone concentrations differed between diets, but not between the 2 subject groups. Comparisons between subject groups for all diets combined showed lower relative insulin resistance and lower AUCs for glucose, insulin, and triacylglycerol in the postobese group. High-starch and high-sucrose diets had no adverse effects on postprandial glycemia, insulinemia, or lipidemia compared with a high-fat diet. A sucrose-rich diet may improve glucose metabolism, but may have an adverse effect on lipidemia, compared with a starch-rich diet. Postobese women seemed to be more insulin-sensitive and more efficient at storing triacylglycerol than were never-obese women, regardless of dietary composition.

What High Schools are Like.

ERIC Educational Resources Information Center

Arnstine, Donald

1987-01-01

Reviews three recent books on high schools: "The Last Little Citadel: American High Schools Since 1940" (Hampel, 1986), "The Shopping Mall High School: Winners and Losers in the Educational Marketplace" (Powell, Farrar, and Cohen, 1985), and "Multiple Realities: A Study of 13 American High Schools" (Tye, 1985). Notes that all three books are based…

ADX: a high field, high power density, advanced divertor and RF tokamak

NASA Astrophysics Data System (ADS)

LaBombard, B.; Marmar, E.; Irby, J.; Terry, J. L.; Vieira, R.; Wallace, G.; Whyte, D. G.; Wolfe, S.; Wukitch, S.; Baek, S.; Beck, W.; Bonoli, P.; Brunner, D.; Doody, J.; Ellis, R.; Ernst, D.; Fiore, C.; Freidberg, J. P.; Golfinopoulos, T.; Granetz, R.; Greenwald, M.; Hartwig, Z. S.; Hubbard, A.; Hughes, J. W.; Hutchinson, I. H.; Kessel, C.; Kotschenreuther, M.; Leccacorvi, R.; Lin, Y.; Lipschultz, B.; Mahajan, S.; Minervini, J.; Mumgaard, R.; Nygren, R.; Parker, R.; Poli, F.; Porkolab, M.; Reinke, M. L.; Rice, J.; Rognlien, T.; Rowan, W.; Shiraiwa, S.; Terry, D.; Theiler, C.; Titus, P.; Umansky, M.; Valanju, P.; Walk, J.; White, A.; Wilson, J. R.; Wright, G.; Zweben, S. J.

2015-05-01

The MIT Plasma Science and Fusion Center and collaborators are proposing a high-performance Advanced Divertor and RF tokamak eXperiment (ADX)—a tokamak specifically designed to address critical gaps in the world fusion research programme on the pathway to next-step devices: fusion nuclear science facility (FNSF), fusion pilot plant (FPP) and/or demonstration power plant (DEMO). This high-field (⩾6.5 T, 1.5 MA), high power density facility (P/S ˜ 1.5 MW m-2) will test innovative divertor ideas, including an ‘X-point target divertor’ concept, at the required performance parameters—reactor-level boundary plasma pressures, magnetic field strengths and parallel heat flux densities entering into the divertor region—while simultaneously producing high-performance core plasma conditions that are prototypical of a reactor: equilibrated and strongly coupled electrons and ions, regimes with low or no torque, and no fuelling from external heating and current drive systems. Equally important, the experimental platform will test innovative concepts for lower hybrid current drive and ion cyclotron range of frequency actuators with the unprecedented ability to deploy launch structures both on the low-magnetic-field side and the high-magnetic-field side—the latter being a location where energetic plasma-material interactions can be controlled and favourable RF wave physics leads to efficient current drive, current profile control, heating and flow drive. This triple combination—advanced divertors, advanced RF actuators, reactor-prototypical core plasma conditions—will enable ADX to explore enhanced core confinement physics, such as made possible by reversed central shear, using only the types of external drive systems that are considered viable for a fusion power plant. Such an integrated demonstration of high-performance core-divertor operation with steady-state sustainment would pave the way towards an attractive pilot plant, as envisioned in the ARC concept