Intercontinental height datum connection with GOCE and GPS-levelling data

NASA Astrophysics Data System (ADS)

Gruber, T.; Gerlach, C.; Haagmans, R.

2012-12-01

In this study an attempt is made to establish height system datum connections based upon a gravity field and steady-state ocean circulation explorer (GOCE) gravity field model and a set of global positioning system (GPS) and levelling data. The procedure applied in principle is straightforward. First local geoid heights are obtained point wise from GPS and levelling data. Then the mean of these geoid heights is computed for regions nominally referring to the same height datum. Subsequently, these local mean geoid heights are compared with a mean global geoid from GOCE for the same region. This way one can identify an offset of the local to the global geoid per region. This procedure is applied to a number of regions distributed worldwide. Results show that the vertical datum offset estimates strongly depend on the nature of the omission error, i.e. the signal not represented in the GOCE model. For a smooth gravity field the commission error of GOCE, the quality of the GPS and levelling data and the averaging control the accuracy of the vertical datum offset estimates. In case the omission error does not cancel out in the mean value computation, because of a sub-optimal point distribution or a characteristic behaviour of the omitted part of the geoid signal, one needs to estimate a correction for the omission error from other sources. For areas with dense and high quality ground observations the EGM2008 global model is a good choice to estimate the omission error correction in theses cases. Relative intercontinental height datum offsets are estimated by applying this procedure between the United State of America (USA), Australia and Germany. These are compared to historical values provided in the literature and computed with the same procedure. The results obtained in this study agree on a level of 10 cm to the historical results. The changes mainly can be attributed to the new global geoid information from GOCE, rather than to the ellipsoidal heights or the

The National Map - Elevation

USGS Publications Warehouse

Gesch, Dean; Evans, Gayla; Mauck, James; Hutchinson, John; Carswell, William J.

2009-01-01

The National Elevation Dataset (NED) is the primary elevation data product produced and distributed by the USGS. The NED provides seamless raster elevation data of the conterminous United States, Alaska, Hawaii, and the island territories. The NED is derived from diverse source data sets that are processed to a specification with a consistent resolution, coordinate system, elevation units, and horizontal and vertical datums. The NED is the logical result of the maturation of the long-standing USGS elevation program, which for many years concentrated on production of topographic map quadrangle-based digital elevation models. The NED serves as the elevation layer of The National Map, and provides basic elevation information for earth science studies and mapping applications in the United States. The NED is a multi-resolution dataset that is updated bimonthly to integrate newly available, improved elevation source data. NED data are available nationally at grid spacings of 1 arc-second (approximately 30 meters) for the conterminous United States, and at 1/3 and 1/9 arc-seconds (approximately 10 and 3 meters, respectively) for parts of the United States. Most of the NED for Alaska is available at 2-arc-second (about 60 meters) grid spacing, where only lower resolution source data exist. Part of Alaska is available at the 1/3-arc-second resolution, and plans are in development for a significant upgrade in elevation data coverage of the State over the next 5 years. Specifications for the NED include the following: *Coordinate system: Geographic (decimal degrees of latitude and longitude), *Horizontal datum: North American Datum of 1983 (NAD 83), *Vertical datum: North American Vertical Datum of 1988 (NAVD 88) over the conterminous United States and varies in other areas, and *Elevation units: Decimal meters.

76 FR 77208 - Affirmation of Vertical Datum for Surveying and Mapping Activities for the Islands of St. Croix...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-12-12

... Datum for Surveying and Mapping Activities for the Islands of St. Croix, St. John, and St. Thomas... datum for surveying and mapping activities for the islands of St. Croix, St. John, and St. Thomas of the... by other Federal surveying and mapping agencies on St. Croix, St. John, and St. Thomas, with the...

75 FR 59095 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-09-27

... Mile 673........ +202 * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in...,434 upstream of Northeast 24th Street. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ADDRESSES...

76 FR 43923 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-22

... downstream of Big Bethel +9 Road. Approximately 20 feet upstream of the confluence +22 with Newmarket Creek... Approximately 30 feet downstream of I-64 +22 *National Geodetic Vertical Datum. +North American Vertical Datum... Center Street. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above...

33 CFR 334.6 - Datum.

Code of Federal Regulations, 2010 CFR

2010-07-01

... datum is the North American Datum of 1983 (NAD 83), unless such geographic coordinates are expressly labeled NAD 83. Geographic coordinates without the NAD 83 reference may be plotted on maps or charts referenced to NAD 83 only after application of the appropriate corrections that are published on the...

75 FR 29246 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-25

.... Pacific Railroad. Just upstream of State None +2352 Highway 19. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the... Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level...

77 FR 26959 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-08

... Creek confluence. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet... County, Indiana, and Incorporated Areas Docket No.: FEMA-B-1171 Big Walnut Creek Approximately 845 feet... feet upstream +692 of Houck Road (North County Road 25 East). * National Geodetic Vertical Datum...

Pathway to 2022: The Ongoing Modernization of the United States National Spatial Reference System

NASA Astrophysics Data System (ADS)

Stone, W. A.; Caccamise, D.

2017-12-01

The National Oceanic and Atmospheric Administration's National Geodetic Survey (NGS) mission is "to define, maintain and provide access to the National Spatial Reference System (NSRS) to meet our nation's economic, social, and environmental needs." The NSRS is an assemblage of geophysical and geodetic models, tools, and data, with the most-visible components being the North American Datum of 1983 (NAD83) and the North American Vertical Datum of 1988 (NAVD88), which together provide a consistent spatial reference framework for myriad geospatial applications and positioning requirements throughout the United States. The NGS is engaged in an ongoing and comprehensive multi-year project of modernizing the NSRS, a makeover necessitated by technological developments and user accuracy requirements, all with a goal of providing a modern, accurate, accessible, and globally aligned national positioning framework exploiting the substantial power and utility of the Global Navigation Satellite System - of both today and tomorrow. The modernized NSRS will include four new-generation geometric terrestrial reference frames (replacing NAD83) and a technically unprecedented geopotential datum (replacing NAVD88), all to be released in 2022 (anticipated). This poster/presentation will describe the justification for this modernization effort and will update the status and planned evolution of the NSRS as 2022 draws ever closer. Also discussed will be recent developments, including the publication of "blueprint" documents addressing technical details of various facets of the modernized NSRS and a continued series of public Geospatial Summits. Supporting/ancillary projects such as Gravity for the Redefinition of the American Vertical Datum (GRAV-D), which will result in the generation of a highly accurate gravimetric geoid - or definitional reference surface (zero elevation) - for the future geopotential datum, and Geoid Slope Validation Surveys (GSVS), which are exploring the achievable

Modernizing the National Spatial Reference System

NASA Astrophysics Data System (ADS)

Smith, D. A.

2016-12-01

The National Spatial Reference System (NSRS) is that system of datums, reference frames, shorelines, software and standards which serve the entire federal civilian geospatial community. It is the mission of the National Geodetic Survey (NGS) to define, maintain and provide access to the NSRS. Currently the NSRS contains three geometric reference frames (NAD 83(2011), NAD 83(PA11) and NAD 83(MA11)), one dynamic height datum (IGLD 85) and 6 vertical datums (NAVD 88, PRVD02, ASVD02, NMVD03, GUVD04, VIVD09). All of these datums are built on aging technology and contain systematic errors that grow more noticeable as access to accurate positioning becomes more widespread. It was determined by NGS in 2007 that this was not sustainable and as such, all datums and reference frames are scheduled to be replaced in 2022. [At the time of this abstract, the exact names of the replacements are being finalized and are expected to be announced by the AGU fall meeting.] Replacing the official datums and reference frames requires a carefully coordinated effort of dozens of interrelated technical projects spanning years (over a decade in some cases) and involving a majority of NGS employees. This talk will cover the plans thus far, projects completed, projects underway and will summarize the NSRS as it is expected to look and be accessed in 2022 and beyond.

Absolute Gravity Datum in the Age of Cold Atom Gravimeters

NASA Astrophysics Data System (ADS)

Childers, V. A.; Eckl, M. C.

2014-12-01

The international gravity datum is defined today by the International Gravity Standardization Net of 1971 (IGSN-71). The data supporting this network was measured in the 1950s and 60s using pendulum and spring-based gravimeter ties (plus some new ballistic absolute meters) to replace the prior protocol of referencing all gravity values to the earlier Potsdam value. Since this time, gravimeter technology has advanced significantly with the development and refinement of the FG-5 (the current standard of the industry) and again with the soon-to-be-available cold atom interferometric absolute gravimeters. This latest development is anticipated to provide improvement in the range of two orders of magnitude as compared to the measurement accuracy of technology utilized to develop ISGN-71. In this presentation, we will explore how the IGSN-71 might best be "modernized" given today's requirements and available instruments and resources. The National Geodetic Survey (NGS), along with other relevant US Government agencies, is concerned about establishing gravity control to establish and maintain high order geodetic networks as part of the nation's essential infrastructure. The need to modernize the nation's geodetic infrastructure was highlighted in "Precise Geodetic Infrastructure, National Requirements for a Shared Resource" National Academy of Science, 2010. The NGS mission, as dictated by Congress, is to establish and maintain the National Spatial Reference System, which includes gravity measurements. Absolute gravimeters measure the total gravity field directly and do not involve ties to other measurements. Periodic "intercomparisons" of multiple absolute gravimeters at reference gravity sites are used to constrain the behavior of the instruments to ensure that each would yield reasonably similar measurements of the same location (i.e. yield a sufficiently consistent datum when measured in disparate locales). New atomic interferometric gravimeters promise a significant

77 FR 6976 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-10

... Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to... Unincorporated Areas of approximately 0.5 mile Taney County. upstream of the White River confluence. Big Shoals... confluence. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground...

Towards the Implementation of Semi-Dynamic Datum for Malaysia

NASA Astrophysics Data System (ADS)

Shariff, N. S.; Gill, J.; Amin, Z. M.; Omar, K. M.

2017-10-01

A semi-dynamic datum provides positions with respect to time while taking into account the secular and non-secular deformations, making it the best approach to adapt with the dynamic processes of the earth. Malaysia, as yet, employs a static datum, i.e., GDM2000, at epoch 2000; though Malaysia has evidently been affected by seismic activity for the past decade. Therefore, this paper seeks to propose a design for implementing a semi-dynamic datum for Malaysia. Methodologically, GPS time series analyses are carried out to investigate the seismic activity of Malaysia, which essentially contributes to the proposed design of the semi-dynamic datum for Malaysia. The implications of implementing a semi-dynamic datum for Malaysia are discussed as well. The results indicate that Malaysia undergoes a complex deformation; whereby the earthquakes - primarily the 2004 Sumatra-Andaman, 2005 Nias and 2012 Northern Sumatra earthquakes - have affected the underlying secular velocities of Malaysia. Consequently, from this information, the proposed design, particularly the secular and non-secular deformation models, is described in detail. The proposed semi-dynamic datum comprises a transformation, temporal, and spatial module, and utilizes a bilinear interpolation method. Overall, this paper aims to contribute to the feasibility of a semi-dynamic datum approach for Malaysia.

Modeling the North American vertical datum of 1988 errors in the conterminous United States

NASA Astrophysics Data System (ADS)

Li, X.

2018-02-01

A large systematic difference (ranging from -20 cm to +130 cm) was found between NAVD 88 (North AmericanVertical Datum of 1988) and the pure gravimetric geoid models. This difference not only makes it very difficult to augment the local geoid model by directly using the vast NAVD 88 network with state-of-the-art technologies recently developed in geodesy, but also limits the ability of researchers to effectively demonstrate the geoid model improvements on the NAVD 88 network. Here, both conventional regression analyses based on various predefined basis functions such as polynomials, B-splines, and Legendre functions and the Latent Variable Analysis (LVA) such as the Factor Analysis (FA) are used to analyze the systematic difference. Besides giving a mathematical model, the regression results do not reveal a great deal about the physical reasons that caused the large differences in NAVD 88, which may be of interest to various researchers. Furthermore, there is still a significant amount of no-Gaussian signals left in the residuals of the conventional regression models. On the other side, the FA method not only provides a better not of the data, but also offers possible explanations of the error sources. Without requiring extra hypothesis tests on the model coefficients, the results from FA are more efficient in terms of capturing the systematic difference. Furthermore, without using a covariance model, a novel interpolating method based on the relationship between the loading matrix and the factor scores is developed for predictive purposes. The prediction error analysis shows that about 3-7 cm precision is expected in NAVD 88 after removing the systematic difference.

Methods of practice and guidelines for using survey-grade global navigation satellite systems (GNSS) to establish vertical datum in the United States Geological Survey

USGS Publications Warehouse

Rydlund, Jr., Paul H.; Densmore, Brenda K.

2012-01-01

Geodetic surveys have evolved through the years to the use of survey-grade (centimeter level) global positioning to perpetuate and post-process vertical datum. The U.S. Geological Survey (USGS) uses Global Navigation Satellite Systems (GNSS) technology to monitor natural hazards, ensure geospatial control for climate and land use change, and gather data necessary for investigative studies related to water, the environment, energy, and ecosystems. Vertical datum is fundamental to a variety of these integrated earth sciences. Essentially GNSS surveys provide a three-dimensional position x, y, and z as a function of the North American Datum of 1983 ellipsoid and the most current hybrid geoid model. A GNSS survey may be approached with post-processed positioning for static observations related to a single point or network, or involve real-time corrections to provide positioning "on-the-fly." Field equipment required to facilitate GNSS surveys range from a single receiver, with a power source for static positioning, to an additional receiver or network communicated by radio or cellular for real-time positioning. A real-time approach in its most common form may be described as a roving receiver augmented by a single-base station receiver, known as a single-base real-time (RT) survey. More efficient real-time methods involving a Real-Time Network (RTN) permit the use of only one roving receiver that is augmented to a network of fixed receivers commonly known as Continually Operating Reference Stations (CORS). A post-processed approach in its most common form involves static data collection at a single point. Data are most commonly post-processed through a universally accepted utility maintained by the National Geodetic Survey (NGS), known as the Online Position User Service (OPUS). More complex post-processed methods involve static observations among a network of additional receivers collecting static data at known benchmarks. Both classifications provide users

Enhanced definition and required examples of common datum imposed by ISO standard

NASA Astrophysics Data System (ADS)

Yan, Yiqing; Bohn, Martin

2017-12-01

According to the ISO Geometrical Product Specifications (GPS), the establishment and definition of common datum for geometrical components are not fully defined. There are two main limitations of this standard. Firstly: the explications of ISO examples of common datums are not matched with their corresponding definitions, and secondly: a full definition of common datum is missing. This paper suggests a new approach for an enhanced definition and concrete examples of common datum and proposes a holistic methodology for establishment of common datum for each geometrical component. This research is based on the analysis of physical behaviour of geometrical components, orientation constraints and invariance classes of datums. This approach fills the definition gaps of common datum based on ISO GPS, thereby eliminating those deficits. As a result, an improved methodology for a fully functional defined definition of common datum was formulated.

The relation of the European Datum to a geocentric reference system

NASA Technical Reports Server (NTRS)

Marsh, J. G.; Douglas, B. C.; Klosko, S. M.

1971-01-01

Over 31,000 precision reduced optical observations of GEOS-1 and 2 in 70 two-day orbital arcs were used at Goddard Space Flight Center (GSFC) in a dynamical solution to determine center-of-mass coordinates for 15 tracking stations on the European Datum. Comparisons with the results obtained at Centre National d'Etudes Spatiales (CNES) give agreement of about 1.5 ppm for chord lengths. After considering a scale correction to the European Datum (ED) of 1950 to account for the absence of geoid heights at the time of its reduction, agreement to a few ppm between the CNES/GSFC and the ED chords is obtained. However, a small systematic difference between survey and satellite results remains for stations in southeastern France and Switzerland.

75 FR 16749 - Federal Geospatial Summit To Provide Information on Upcoming Improvements To the National Spatial...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-02

...), Including the Replacement of the North American Datum of 1983 (NAD 83) and the North American Vertical Datum... Datum of 1983 (NAD 83), the North American Vertical Datum of 1988 (NAVD 88), and other state and... effort to support these rapid changes in positioning technologies, NGS has adopted a plan to replace NAD...

76 FR 1121 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-07

... approximately 410 feet of Lewis County. upstream of U.S. Route 61 Business. * National Geodetic Vertical Datum... intersection of Impact Drive and FM Road 2404. * National Geodetic Vertical Datum. + North American Vertical..., Environmental Consideration. An environmental impact assessment has not been prepared. Regulatory Flexibility...

Levels at streamflow gaging stations

USGS Publications Warehouse

Kennedy, E.J.

1988-01-01

This manual establishes the surveying procedures for setting gages at a streamflow gaging station to datum and for checking them periodically for errors caused by vertical movement of the gage-supporting structures. The surveying terms and concepts used are explained; and the details of testing, adjusting, and operating the instruments are outlined. Notekeeping, adjusting level circuits, checking gages, summarizing results, locating the nearest National Geodetic Vertical Datum of 1929 bench mark, and relating the gage datum to the national datum are described.

Levels at streamflow gaging stations

USGS Publications Warehouse

Kennedy, E.J.

1990-01-01

This manual establishes the surveying procedures for (1) setting gages at a streamflow gaging station to datum and (2) checking the gages periodically for errors caused by vertical movement of the structures that support them. Surveying terms and concepts are explained, and procedures for testing, adjusting, and operating the instruments are described in detail. Notekeeping, adjusting level circuits, checking gages, summarizing results, locating the nearest National Geodetic Vertical Datum of 1929 bench mark, and relating the gage datum to the national datum are also described.

Wave equation datuming applied to S-wave reflection seismic data

NASA Astrophysics Data System (ADS)

Tinivella, U.; Giustiniani, M.; Nicolich, R.

2018-05-01

S-wave high-resolution reflection seismic data was processed using Wave Equation Datuming technique in order to improve signal/noise ratio, attenuating coherent noise, and seismic resolution and to solve static corrections problems. The application of this algorithm allowed obtaining a good image of the shallow subsurface geological features. Wave Equation Datuming moves shots and receivers from a surface to another datum (the datum plane), removing time shifts originated by elevation variation and/or velocity changes in the shallow subsoil. This algorithm has been developed and currently applied to P wave, but it reveals the capacity to highlight S-waves images when used to resolve thin layers in high-resolution prospecting. A good S-wave image facilitates correlation with well stratigraphies, optimizing cost/benefit ratio of any drilling. The application of Wave Equation Datuming requires a reliable velocity field, so refraction tomography was adopted. The new seismic image highlights the details of the subsoil reflectors and allows an easier integration with borehole information and geological surveys than the seismic section obtained by conventional CMP reflection processing. In conclusion, the analysis of S-wave let to characterize the shallow subsurface recognizing levels with limited thickness once we have clearly attenuated ground roll, wind and environmental noise.

Spectral characteristics of the Hellenic vertical network - Validation over Central and Northern Greece using GOCE/GRACE global geopotential models

NASA Astrophysics Data System (ADS)

Andritsanos, Vassilios D.; Vergos, George S.; Grigoriadis, Vassilios N.; Pagounis, Vassilios; Tziavos, Ilias N.

2014-05-01

The Elevation project, funded by the action "Archimedes III - Funding of research groups in T.E.I.", co-financed by the E.U. (European Social Fund) and national funds under the Operational Program "Education and Lifelong Learning 2007-2013" aims mainly to the validation of the Hellenic vertical datum. This validation is carried out over two areas under study, one in Central and another in Northern Greece. During the first stage of the validation process, satellite-only as well as combined satellite-terrestrial models of the Earth's geopotential are used. GOCE and GRACE satellite information is compared against recently measured GPS/Levelling observations at specific benchmarks of the vertical network in Attiki (Central Greece) and Thessaloniki (Northern Greece). A spectral enhancement approach is followed where, given the GOCE/GRACE GGM truncation degree, EGM2008 is used to fill-in the medium and high-frequency content along with RTM effects for the high and ultra high part. The second stage is based on the localization of possible blunders of the vertical network using the spectral information derived previously. The undoubted accuracy of the contemporary global models at the low frequency band leads to some initial conclusions about the consistency of the Hellenic vertical datum.

Global height datum unification: a new approach in gravity potential space

NASA Astrophysics Data System (ADS)

Ardalan, A. A.; Safari, A.

2005-12-01

The problem of “global height datum unification” is solved in the gravity potential space based on: (1) high-resolution local gravity field modeling, (2) geocentric coordinates of the reference benchmark, and (3) a known value of the geoid’s potential. The high-resolution local gravity field model is derived based on a solution of the fixed-free two-boundary-value problem of the Earth’s gravity field using (a) potential difference values (from precise leveling), (b) modulus of the gravity vector (from gravimetry), (c) astronomical longitude and latitude (from geodetic astronomy and/or combination of (GNSS) Global Navigation Satellite System observations with total station measurements), (d) and satellite altimetry. Knowing the height of the reference benchmark in the national height system and its geocentric GNSS coordinates, and using the derived high-resolution local gravity field model, the gravity potential value of the zero point of the height system is computed. The difference between the derived gravity potential value of the zero point of the height system and the geoid’s potential value is computed. This potential difference gives the offset of the zero point of the height system from geoid in the “potential space”, which is transferred into “geometry space” using the transformation formula derived in this paper. The method was applied to the computation of the offset of the zero point of the Iranian height datum from the geoid’s potential value W 0=62636855.8 m2/s2. According to the geometry space computations, the height datum of Iran is 0.09 m below the geoid.

Straightness measurement using laser beam straight datum

NASA Astrophysics Data System (ADS)

Uchikoshi, Junichi; Shimada, Shoichi; Ikawa, Naoya; Komura, Akio

1995-08-01

Using the direction stabilized laser beam as a physical straight datum, instead of the tangible reference surface, a method is proposed for the measurement of an error motion of a slide table and/or surface profile of mechanical components. A specially designed 2D position sensor/compensator for laser beam center is developed combining a quadrant photo-diode (QPD) position sensor for beam center and the piezo-compensator which compensates the beam shift from the center of QPD. By the use the sensor/compensator proposed, the positional and angular fluctuations of laser beam path is evaluated with nanometric resolution. Combining the sensor with the piezo-driven mirror compensator, the directional stabilizer for the laser beam is also designed in the same manner as the sensor/compensator. The stabilized He-Ne laser beam can be used as the metrological datum of straightness within the accuracy of 2 X 10 -8 rad. By mounting the position sensor/compensator on a slide table, the carriage with working distance of 1 m is so designed and built as to move straight along the stabilized laser beam. The carriage can be used as a mechanical straight datum with the accuracy equivalent to the laser beam stability.

Assessing risk of navigational hazard from sea-level-related datum in the South West of Java Sea, Indonesia

NASA Astrophysics Data System (ADS)

Poerbandono

2017-07-01

This paper assesses the presence of navigational hazards due to underestimation of charted depths originated from an establishment of a sea-level-related reference plane, i.e. datum. The study domain is situated in one of Indonesia's densest marine traffic, SW Java Sea, Indonesia. The assessment is based on the comparison of the authorized Chart Datum (CD), being uniformly located at 0.6 m below Mean Sea Level (MSL), and a spatially varying Lowest Astronomical Tide (LAT) generated for the purpose of this research. Hazards are considered here as the deviation of LAT from CD and quantified as the ratio of LAT -CD deviation with respect to the allowable Total Vertical Uncertainty (TVU), i.e. the international standard for accuracy of depth information on nautical charts. Underestimation of charted depth is expected for the case that LAT falls below CD. Such a risk magnifies with decreasing depths, as well as the increasing volume of traffic and draught of the vessel. It is found that most of the domain is in the interior of risk-free zone from using uniform CD. As much as 0.08 and 0.19 parts of the area are in zones where the uncertainty of CD contributes respectively to 50% and 30% of Total Vertical Uncertainty. These are zones where the hazard of navigation is expected to increase due to underestimated lowest tidal level.

33 CFR 110.128d - Island of Oahu, Hawaii. (Datum: OHD)

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Island of Oahu, Hawaii. (Datum: OHD) 110.128d Section 110.128d Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY ANCHORAGES ANCHORAGE REGULATIONS Special Anchorage Areas § 110.128d Island of Oahu, Hawaii. (Datum...

77 FR 71702 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-04

... from the requirements of 44 CFR part 10, Environmental Consideration. An environmental impact... Rock +3405 Creek (Lower) confluence. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ADDRESSES...

78 FR 29652 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-21

..., Louisiana, and Incorporated Areas Docket No.: FEMA-B-1110 Big Creek Just upstream of Burke +78... confluence with +79 Unincorporated Areas of Big Creek. Richland Parish. Just upstream of Smalling +85 Road.... * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [supcaret...

Datum Feature Extraction and Deformation Analysis Method Based on Normal Vector of Point Cloud

NASA Astrophysics Data System (ADS)

Sun, W.; Wang, J.; Jin, F.; Liang, Z.; Yang, Y.

2018-04-01

In order to solve the problem lacking applicable analysis method in the application of three-dimensional laser scanning technology to the field of deformation monitoring, an efficient method extracting datum feature and analysing deformation based on normal vector of point cloud was proposed. Firstly, the kd-tree is used to establish the topological relation. Datum points are detected by tracking the normal vector of point cloud determined by the normal vector of local planar. Then, the cubic B-spline curve fitting is performed on the datum points. Finally, datum elevation and the inclination angle of the radial point are calculated according to the fitted curve and then the deformation information was analyzed. The proposed approach was verified on real large-scale tank data set captured with terrestrial laser scanner in a chemical plant. The results show that the method could obtain the entire information of the monitor object quickly and comprehensively, and reflect accurately the datum feature deformation.

77 FR 41323 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-13

.... Approximately 800 feet +7655 upstream of Virginia Street. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter..., Illinois, and Incorporated Areas Docket No.: FEMA-B-1197 Big Rock Creek Approximately 1.68 miles +648...

77 FR 49373 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-16

.... Macon Bayou Just upstream of Private +108 City of Eudora. Road. Just upstream of Verser +108 Road... Areas of Road. Logan County. Just downstream of Newton +563 Road. Just upstream of West 9th +621 Street... Road. * National Geodetic Vertical Datum. + North American Vertical Datum. Depth in feet above ground...

Wave equation datuming applied to marine OBS data and to land high resolution seismic profiling

NASA Astrophysics Data System (ADS)

Barison, Erika; Brancatelli, Giuseppe; Nicolich, Rinaldo; Accaino, Flavio; Giustiniani, Michela; Tinivella, Umberta

2011-03-01

One key step in seismic data processing flows is the computation of static corrections, which relocate shots and receivers at the same datum plane and remove near surface weathering effects. We applied a standard static correction and a wave equation datuming and compared the obtained results in two case studies: 1) a sparse ocean bottom seismometers dataset for deep crustal prospecting; 2) a high resolution land reflection dataset for hydrogeological investigation. In both cases, a detailed velocity field, obtained by tomographic inversion of the first breaks, was adopted to relocate shots and receivers to the datum plane. The results emphasize the importance of wave equation datuming to properly handle complex near surface conditions. In the first dataset, the deployed ocean bottom seismometers were relocated to the sea level (shot positions) and a standard processing sequence was subsequently applied to the output. In the second dataset, the application of wave equation datuming allowed us to remove the coherent noise, such as ground roll, and to improve the image quality with respect to the application of static correction. The comparison of the two approaches evidences that the main reflecting markers are better resolved when the wave equation datuming procedure is adopted.

Gravimetric investigations on the North American Datum (1972 - 1973)

NASA Technical Reports Server (NTRS)

Mather, R. S.

1975-01-01

All the available unclassified gravity data on the North American Datum (NAD) and in the surrounding oceans was assembled late in 1972 for the investigation of the gravity field in North America and its relation to North American Datum 1927 (NAD 27). The gravity data in Canada and the United States was compiled on a common datum compatible with the International Gravity Standardization Network 1971 (IGSN 71). The variation in the error of representation in the region is studied along with the correlation characteristics of gravity anomalies with elevation. A free air geoid (FAG 73) was computed from a combination of surface gravity data and Goddard Earth Model (GEM) 4 and this was used as the basis for the computation of the non-Stokesian contributions to the height anomaly. The geocentric orientation parameters obtained by this astrogravimetric method are compared with those obtained by satellite techniques. The differences are found to be no greater than those between individual satellite solutions. The differences between the astrogravimetric solution and satellite solutions GSFC 73 and GEM 6 are studied in detail with a view to obtaining a better understanding of these discrepancies.

33 CFR 110.168 - Hampton Roads, Virginia and adjacent waters (Datum: NAD 83).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Hampton Roads, Virginia and adjacent waters (Datum: NAD 83). 110.168 Section 110.168 Navigation and Navigable Waters COAST GUARD..., Virginia and adjacent waters (Datum: NAD 83). (a) Anchorage Grounds—(1) Anchorage A [Naval Anchorage]. The...

GPS Tides and Datums

DTIC Science & Technology

1994-07-01

REPORT DOCUMENTATION PAGE Form Ap~ovd -qmp Pu~~~~~~~~~~hc~~~~~ omef.A Nu0001U~ 0Itg O Mcq ~n, ’tmoa1a q 0 0 fft *cuqIO~ ’W𔃻i.q~ii os .ete .7qO0t.Aqea...water level heights. Using OTF technology it should be possible to obtain a time series of water surface heights to an accuracy of 1 to 2 ymfa...receiver location. 14. SUBJECT TERMS 15. NUMBER OF PAGES On-the-Fly, study of water levels , datum, Bay of Fundy 10 16. PRICE CODE 17. SECURITY

33 CFR 110.235 - Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). 110.235 Section 110.235 Navigation and Navigable Waters COAST... Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). (a) The anchorage grounds—(1...

33 CFR 110.235 - Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 33 Navigation and Navigable Waters 1 2014-07-01 2014-07-01 false Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). 110.235 Section 110.235 Navigation and Navigable Waters COAST... Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). (a) The anchorage grounds—(1...

33 CFR 110.235 - Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 33 Navigation and Navigable Waters 1 2012-07-01 2012-07-01 false Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). 110.235 Section 110.235 Navigation and Navigable Waters COAST... Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). (a) The anchorage grounds—(1...

33 CFR 110.235 - Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 33 Navigation and Navigable Waters 1 2013-07-01 2013-07-01 false Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). 110.235 Section 110.235 Navigation and Navigable Waters COAST... Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). (a) The anchorage grounds—(1...

33 CFR 110.235 - Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). 110.235 Section 110.235 Navigation and Navigable Waters COAST... Pacific Ocean (Mamala Bay), Honolulu Harbor, Hawaii (Datum: NAD 83). (a) The anchorage grounds—(1...

Upcoming replacements for NAD83, NAVD88 and IGLD85

NASA Astrophysics Data System (ADS)

Smith, D. A.; Snay, R.

2009-05-01

The National Geodetic Survey (NGS), part of the National Oceanic and Atmospheric Administration (NOAA) is responsible for defining, maintaining and providing access to the National Spatial Reference System (NSRS) for the United States. The NSRS is the official system to which all civil federal mapping agencies should refer, and contains, amongst other things, the official geopotential (historically "vertical") datum of NAVD 88, the 3-D geometric reference system (historically "horizontal datum") of NAD 83 and great lakes datum (IGLD 85). Although part of the United States NSRS, all three of these datums have been created through international partnerships across North America. Unfortunately, time has shown both the systematic errors existent within these datums, as well as the inherent weaknesses of relying exclusively on passive monuments to define and provide access to these datums. In recognition of these issues, the National Geodetic Survey has issued a "10 year plan", available online, which outlines steps which will be taken to update NAD 83, NAVD 88 and IGLD 85 concurrently around the year 2018. The primary source of success will be in the refinement of the CORS network and the upcoming execution of the GRAV-D project (Gravity for the Re-definition of the American Vertical Datum). Conversations are ongoing with colleagues in Canada, Mexico, Central America and the Caribbean in order to coordinate all of these efforts across the entire continent. The largest changes expected to occur are the removal of over 2 meters of non-geocentricity in NAD 83; the removal of decimeters of bias and over a meter of tilt in NAVD 88; the addition of the ability to track crustal motions (subsidence, tectonics, etc) in the datums; the removal of leveling as a tool for long-line height differencing; the use of a "best" geoid as the orthometric height reference surface; the addition of datum velocities (motions of the 3-D geometric reference system origin and motions of the geoid

On the unification of geodetic leveling datums using satellite altimetry

NASA Technical Reports Server (NTRS)

Mather, R. S.; Rizos, C.; Morrison, T.

1978-01-01

Techniques are described for determining the height of Mean Sea Level (MSL) at coastal sites from satellite altimetry. Such information is of value in the adjustment of continental leveling networks. Numerical results are obtained from the 1977 GEOS-3 altimetry data bank at Goddard Space Flight Center using the Bermuda calibration of the altimeter. Estimates are made of the heights of MSL at the leveling datums for Australia and a hypothetical Galveston datum for central North America. The results obtained are in reasonable agreement with oceanographic estimates obtained by extrapolation. It is concluded that all gravity data in the Australian bank AUSGAD 76 and in the Rapp data file for central North America refer to the GEOS-3 altimeter geoid for 1976.0 with uncertainties which do not exceed + or - 0.1 mGal.

Comparing mean high water and high water line shorelines: Should prosy-datum offsets be incorporated into shoreline change analysis?

USGS Publications Warehouse

Moore, L.J.; Ruggiero, P.; List, J.H.

2006-01-01

More than one type of shoreline indicator can be used in shoreline change analyses, and quantifying the effects of this practice on the resulting shoreline change rates is important. Comparison of three high water line (proxy-based) shorelines and a mean high water intercept (datum-based) shoreline collected from simultaneous aerial photographic and lidar surveys of a relatively steep reflective beach (tan ?? = 0.07), which experiences a moderately energetic wave climate (annual average Hs = 1.2 m), reveals an average horizontal offset of 18.8 m between the two types of shoreline indicators. Vertical offsets are also substantial and are correlated with foreshore beach slope and corresponding variations in wave runup. Incorporating the average horizontal offset into both a short-term, endpoint shoreline change analysis and a long-term, linear regression analysis causes rates to be shifted an average of -0.5 m/y and -0.1 m/y, respectively. The rate shift increases with increasing horizontal offset and decreasing measurement intervals and, depending on the rapidity of shoreline change rates, is responsible for varying degrees of analysis error. Our results demonstrate that under many circumstances, the error attributable to proxy-datum offsets is small relative to shoreline change rates and thus not important. Furthermore, we find that when the error associated with proxy-datum offsets is large enough to be important, the shoreline change rates themselves are not likely to be significant. A total water level model reveals that the high water line digitized by three independent coastal labs for this study was generated by a combination of large waves and a high tide several days before the collection of aerial photography. This illustrates the complexity of the high water line as a shoreline indicator and calls into question traditional definitions, which consider the high water line a wetted bound or "marks left by the previous high tide.".

Datum Transformation of Spatial Data and Application in Cadastre

NASA Astrophysics Data System (ADS)

Kısa, A.; Erkek, B.; Ekin, L.

2012-07-01

In Turkey, cadastral works have been started with local-based works in 1924 and speeded up after 1950's by using photogrammetry. Different measurement methods, coordinate systems and scales have been used in these works. As a result of primary cadastral activities two main products are generated; cadastral maps and title deeds. After this, cadastral data live on the maps, by cadastral activities carried out by cadastral offices and title deed data live on the registrations by land registration activities carried out by land registration offices. Up to 2005 different references systems such as local (graphic) and ED50 have been used for Cadastral maps production. 2000's Land Registry and Cadastre Information System (TAKBİS) Project has started as a pilot application by Land Registry and Cadastre (TKGM). After completion of pilot project spreading activities started in 2005 and still has been ongoing. On the other hand The government has taken the decision to finish primary cadastral activities within three years. The primary cadastral activities completed at the end of 2008. And also TKGM has completed metadata portal in 2008. At last, cadastral map updating (renovation) started in 2009 by using digital orthophoto with 30 cm GSD. Today people have great expectations in accomplishing digital cadastral services, they need correct, reliable, easy and quick accessible land register and cadastral survey information. Even such request expressed in INPIRE directive by using ISO 191XX data standards. This means we have great hard work for spatial data conversion, datum and data transformation for map and cadastral data harmonization. This paper presents results of investigation of used cadastral maps and used datums of the TKGM and possible transformation methods of datum and some recommendations for future applications.

Network global navigation satellite system survey to harmonize water-surface elevation data for the Rainy River Basin

USGS Publications Warehouse

Ziegeweid, Jeffrey R.; Silliker, R. Jason; Densmore, Brenda K.; Krahulik, Justin

2016-08-15

Continuously recording water-level streamgages in Rainy Lake and Namakan Reservoir are used to regulate water levels according to rule curves established in 2000 by the International Joint Commission; however, water levels at streamgages were referenced to a variety of vertical datums, confounding efforts to model the flow of water through the system, regulate water levels during periods of high inflow, and evaluate the effectiveness of the rule curves. In October 2014, the U.S. Geological Survey, Natural Resources Canada, International Joint Commission, and National Park Service began a joint field study with the goal of obtaining precise elevations referenced to a uniform vertical datum for all reference marks used to set water levels at streamgages throughout Rainy Lake and Namakan Reservoir. This report was prepared by the U.S. Geological Survey in cooperation with Natural Resources Canada, International Joint Commission, and National Park Service.Three field crews deployed Global Navigation Satellite System receivers statically over 16 reference marks colocated with active and discontinued water-level streamgages throughout Rainy River, Rainy Lake, Namakan Reservoir, and select tributaries of Rainy Lake and Namakan Reservoir. A Global Navigation Satellite System receiver also was deployed statically over a National Geodetic Survey cooperative base network control station for use as a quality-control reference mark. Satellite data were collected simultaneously during a 5-day period and processed independently by the U.S. Geological Survey and Natural Resources Canada to obtain accurate positioning and elevations for the 17 surveyed reference marks. Processed satellite data were used to convert published water levels to elevations above sea level referenced to the Canadian Geodetic Vertical Datum of 2013 in order to compare water-surface elevations referenced to a uniform vertical datum throughout the study area. In this report, an “offset” refers to the

77 FR 76916 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-31

... Southeast. Sweat Mountain Creek At the Willeo Creek +941 Unincorporated Areas of confluence. Cobb County... upstream of the Sweat Mountain Creek confluence. * National Geodetic Vertical Datum. + North American...

U.S.A. National Surface Rock Density Map - Part 2

NASA Astrophysics Data System (ADS)

Winester, D.

2016-12-01

A map of surface rock densities over the USA has been developed by the NOAA-National Geodetic Survey (NGS) as part of its Gravity for the Redefinition of the American Vertical Datum (GRAV-D) Program. GRAV-D is part of an international effort to generate a North American gravimetric geoid for use as the vertical datum reference surface. As a part of modeling process, it is necessary to eliminate from the observed gravity data the topographic and density effects of all masses above the geoid. However, the long-standing tradition in geoid modeling, which is to use an average rock density (e.g. 2.67 g/cm3), does not adequately represent the variety of lithologies in the USA. The U.S. Geological Survey has assembled a downloadable set of surface geologic formation maps (typically 1:100,000 to 1:500, 000 scale in NAD27) in GIS format. The lithologies were assigned densities typical of their rock type (Part 1) and these variety of densities were then rasterized and averaged over one arc-minute areas. All were then transformed into WGS84 datum. Thin layers of alluvium and some water bodies (interpreted to be less than 40 m thick) have been ignored in deference to underlying rocks. Deep alluvial basins have not been removed, since they represent significant fraction of local mass. The initial assumption for modeling densities will be that the surface rock densities extend down to the geoid. If this results in poor modeling, variable lithologies with depth can be attempted. Initial modeling will use elevations from the SRTM DEM. A map of CONUS densities is presented (denser lithologies are shown brighter). While a visual map at this scale does show detailed features, digital versions are available upon request. Also presented are some pitfalls of using source GIS maps digitized from variable reference sources, including the infamous `state line faults.'

75 FR 5929 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-02-05

... City of Eureka Springs, miles upstream of Unincorporated Areas Magnetic Road. of Carroll County. Approximately 1,250 None +1,131 feet upstream of Magnetic Road. * National Geodetic Vertical Datum. + North...

Nearshore coastal bathymetry data collected in 2016 from West Ship Island to Horn Island, Gulf Islands National Seashore, Mississippi

USGS Publications Warehouse

DeWitt, Nancy T.; Stalk, Chelsea A.; Fredericks, Jake J.; Flocks, James G.; Kelso, Kyle W.; Farmer, Andrew S.; Tuten, Thomas M.; Buster, Noreen A.

2018-04-13

The U.S. Geological Survey (USGS) St. Petersburg Coastal and Marine Science Center, in cooperation with the U.S. Army Corps of Engineers, Mobile District, conducted bathymetric surveys of the nearshore waters surrounding Ship and Horn Islands, Gulf Islands National Seashore, Mississippi. The objective of this study was to establish base-level elevation conditions around West Ship, East Ship, and Horn Islands and their associated active littoral system prior to restoration activities. These activities include the closure of Camille Cut and the placement of sediment in the littoral zone of East Ship Island. These surveys can be compared with future surveys to monitor sediment migration patterns post-restoration and can also be measured against historic bathymetric datasets to further our understanding of island evolution.The USGS collected 667 line-kilometers (km) of single-beam bathymetry data and 844 line-km of interferometric swath bathymetry data in July 2016 under Field Activity Number 2016-347-FA. Data are provided in three datums: (1) the International Terrestrial Reference Frame of 2000 (ellipsoid height); (2) the North American Datum of 1983 (NAD83) CORS96 realization and the North American Vertical Datum of 1988 with respect to the GEOID12B model (orthometric height); and (3) NAD83 (CORS96) and Mean Lower Low Water (tidal datum). Data products, including x,y,zpoint datasets, trackline shapefiles, digital and handwritten Field Activity Collection Systems logs, 50-meter digital elevation model, and formal Federal Geographic Data Committee metadata, are available for download.

NGS’ GRAV-D Project: Current update and future prospects

NASA Astrophysics Data System (ADS)

Childers, V. A.; Smith, D. A.; Roman, D. R.; Diehl, T. M.; Eckl, M. C.

2009-12-01

NOAA’s National Geodetic Survey (NGS) is tasked with establishing and maintaining the National Spatial Reference System, the vertical portion of which is called the North American Vertical Datum of 1988 (NAVD88). Although errors were known to exist in NAVD88, recent comparison with Gravity Recovery and Climate Experiment (GRACE) satellite gravity data demonstrated that the error was significant: 50 cm average with a 1 m tilt across the country. Instead of re-leveling the country to repair the datum, NGS has decided instead to establish a new vertical datum through the creation of a gravimetric geoid accurate to 2 cm. At this time, NGS's gravity holdings are of insufficient quality and density to allow for a geoid to be created at this level of accuracy. NGS has launched the Gravity for the Re-definition of the American Vertical Datum (GRAV-D) Project to both sufficiently densify our gravity holdings and to monitor and incorporate temporal changes to the geoid. GRAV-D will perform airborne gravity measurement of all of the US and its holdings in the next 10 years to provide a uniformly measured recovery of the gravity field at about a 20 km resolution. In addition, areas of most rapid change will be monitored through absolute and relative gravity measurements, the GRACE time-varying gravity field, and GPS/CORS networks. In FY09, GRAV-D performed a number of surveys in the Gulf of Mexico, Puerto Rico/US Virgin Islands, and Alaska. We discuss these surveys and a vision of the future given likely Congressional funding in FY10 and onward.

The deep structure of the Sichuan basin and adjacent orogenic zones revealed by the aggregated deep seismic profiling datum

NASA Astrophysics Data System (ADS)

Xiong, X.; Gao, R.; Li, Q.; Wang, H.

2012-12-01

The sedimentary basin and the orogenic belt are the basic two tectonic units of the continental lithosphere, and form the basin-mountain coupling system, The research of which is the key element to the oil and gas exploration, the global tectonic theory and models and the development of the geological theory. The Sichuan basin and adjacent orogenic belts is one of the most ideal sites to research the issues above, in particular by the recent deep seismic profiling datum. From the 1980s to now, there are 11 deep seismic sounding profiles and 6 deep seismic reflection profiles and massive seismic broadband observation stations deployed around and crossed the Sichuan basin, which provide us a big opportunity to research the deep structure and other forward issues in this region. Supported by the National Natural Science Foundation of China (Grant No. 41104056) and the Fundamental Research Funds of the Institute of Geological Sciences, CAGS (No. J1119), we sampled the Moho depth and low-velocity zone depth and the Pn velocity of these datum, then formed the contour map of the Moho depth and Pn velocity by the interpolation of the sampled datum. The result shows the Moho depth beneath Sichuan basin ranges from 40 to 44 km, the sharp Moho offset appears in the western margin of the Sichuan basin, and there is a subtle Moho depression in the central southern part of the Sichuan basin; the P wave velocity can be 6.0 km/s at ca. 10 km deep, and increases gradually deeper, the average P wave velocity in this region is ca. 6.3 km/s; the Pn velocity is ca. 8.0-8.02 km/s in Sichuan basin, and 7.70-7.76 km/s in Chuan-Dian region; the low velocity zone appears in the western margin of the Sichuan basin, which maybe cause the cause of the earthquake.

InSAR datum connection using GNSS-augmented radar transponders

NASA Astrophysics Data System (ADS)

Mahapatra, Pooja; der Marel, Hans van; van Leijen, Freek; Samiei-Esfahany, Sami; Klees, Roland; Hanssen, Ramon

2018-01-01

Deformation estimates from Interferometric Synthetic Aperture Radar (InSAR) are relative: they form a `free' network referred to an arbitrary datum, e.g. by assuming a reference point in the image to be stable. However, some applications require `absolute' InSAR estimates, i.e. expressed in a well-defined terrestrial reference frame, e.g. to compare InSAR results with those of other techniques. We propose a methodology based on collocated InSAR and Global Navigation Satellite System (GNSS) measurements, achieved by rigidly attaching phase-stable millimetre-precision compact active radar transponders to GNSS antennas. We demonstrate this concept through a simulated example and practical case studies in the Netherlands.

National Elevation Dataset

USGS Publications Warehouse

,

1999-01-01

The National Elevation Dataset (NED) is a new raster product assembled by the U.S. Geological Survey (USGS). The NED is designed to provide national elevation data in a seamless form with a consistent datum, elevation unit, and projection. Data corrections were made in the NED assembly process to minimize artifacts, permit edge matching, and fill sliver areas of missing data.

Potentiometric Surfaces and Water-Level Trends in the Cockfield and Wilcox Aquifers of Southern and Northeastern Arkansas, 2006

USGS Publications Warehouse

Schrader, T.P.

2007-01-01

The Cockfield Formation of Claiborne Group and the Wilcox Group contain aquifers that provide sources of ground water in southern and northeastern Arkansas. In 2000, about 9.9 million gallons per day was withdrawn from the Cockfield Formation of Claiborne Group and about 22.2 million gallons per day was withdrawn from the Wilcox Group. Major withdrawals from the aquifers were for industrial and public water supplies. A study was conducted by the U.S. Geological Survey in cooperation with the Arkansas Natural Resources Commission and the Arkansas Geological Survey to determine the water level associated with the aquifers in the Cockfield Formation of Claiborne Group and the Wilcox Group in southern and northeastern Arkansas. During February and March 2006, 56 water-level measurements were made in wells completed in the Cockfield aquifer and 59 water-level measurements were made in wells completed in the Wilcox aquifer, 16 in southwestern and 43 in northeastern Arkansas. This report presents the results as potentiometric-surface maps and as long-term water-level hydrographs. The regional direction of ground-water flow in the Cockfield Formation of Claiborne Group generally is towards the east and southeast, away from the outcrop, except in areas of intense ground-water withdrawals, such as western Drew County, southeastern Lincoln County, southwestern Calhoun County, and near Crossett in Ashley County. There are three cones of depression indicated by relatively low water-level altitudes in southeastern Lincoln County, southwestern Calhoun County, and near Crossett in Ashley County. The lowest water-level altitude measured was 44 feet above the National Geodetic Vertical Datum of 1929 in Lincoln County; the highest water-level altitude measured was 346 feet above the National Geodetic Vertical Datum of 1929 in Columbia County at the outcrop area. Hydrographs from 40 wells with historical water levels from 1986 to 2006 were evaluated using linear regression to

Integrating Continuous GPS Time Series and Geodetic Leveling Data to Estimate Secular Vertical Velocity of Taiwan

NASA Astrophysics Data System (ADS)

LAI, Y. R.; Hsu, Y. J.; You, R. J.

2017-12-01

GPS technique services as the most powerful method in monitoring crustal deformation owing to its advantage of temporal continuity. Geodetic leveling is also widely used not only in engineering but also in geophysics applicants due to its high precision in vertical datum determination and spatial continuity advantages. As widely known, the reference frames of GPS and geodetic leveling are different- the former refers to the reference ellipsoid (WGS84 ellipsoid) and the latter refers to the geoid. In order to combine vertical velocity fields from different datums, we decide to examine discrepancy between these two data sets. Moreover, GPS stations and benchmarks always do not locate at the same places. In place of using a spatial reduced function (Ching et.al, JGR, 2011) to find the discrepancy between them, we focused on comparing termporal variation of GPS vertical motions and geodetic leveling displacements. In this study, we analyzed the vertical velocity field from 238 GPS stations and 1634 benchmarks, including the time-period (2000 to 2015) influenced by postseismiceffects from 1999 Chi-Chi earthquake (Mw 7.6), 2003 Chengkung earthquake (Mw 6.8), and so on. After we thoroughly examined all the process and considered coseismic and postseismic deformation of significant earthquakes, we found that the discrepancy of vertical velocity of the GPS station and its nearby benchmarks is about 1 - 2 mm/yr, including several source of errors in data processing. We suggest that this discrepancy of vertical velocity field can be ignored as tolerable error, and two heterogeneous fields can be integrated together without any mathematical presumptions of spatial regression. The result shows that the western coast is suffering sever subsidence with rates up to 40 mm/yr; the Central Range of Taiwan is uplifting with rates about +10 mm/yr and active landslides with significant subsidence of 5-10 mm/yr in local area. A huge velocity contrast of 30 mm;/yr indicating east over

Unification of Intercontinental Height Systems based on the Fixed Geodetic Boundary Value Problem - A Case Study in Spherical Approximation

NASA Astrophysics Data System (ADS)

Grombein, T.; Seitz, K.; Heck, B.

2013-12-01

In general, national height reference systems are related to individual vertical datums defined by specific tide gauges. The discrepancy of these vertical datums causes height system biases that range in an order of 1-2 m at a global scale. Continental height systems can be connected by spirit leveling and gravity measurements along the leveling lines as performed for the definition of the European Vertical Reference Frame. In order to unify intercontinental height systems, an indirect connection is needed. For this purpose, global geopotential models derived from recent satellite missions like GOCE provide an important contribution. However, to achieve a highly-precise solution, a combination with local terrestrial gravity data is indispensable. Such combinations result in the solution of a Geodetic Boundary Value Problem (GBVP). In contrast to previous studies, mostly related to the traditional (scalar) free GBVP, the present paper discusses the use of the fixed GBVP for height system unification, where gravity disturbances instead of gravity anomalies are applied as boundary values. The basic idea of our approach is a conversion of measured gravity anomalies to gravity disturbances, where unknown datum parameters occur that can be associated with height system biases. In this way, the fixed GBVP can be extended by datum parameters for each datum zone. By evaluating the GBVP at GNSS/leveling benchmarks, the unknown datum parameters can be estimated in a least squares adjustment. Beside the developed theory, we present numerical results of a case study based on the spherical fixed GBVP and boundary values simulated by the use of the global geopotential model EGM2008. In a further step, the impact of approximations like linearization as well as topographic and ellipsoidal effects is taken into account by suitable reduction and correction terms.

Combined High-Resolution LIDAR Topography and Multibeam Bathymetry for Northern Resurrection Bay, Seward, Alaska

USGS Publications Warehouse

Labay, Keith A.; Haeussler, Peter J.

2008-01-01

A new Digital Elevation Model was created using the best available high-resolution topography and multibeam bathymetry surrounding the area of Seward, Alaska. Datasets of (1) LIDAR topography collected for the Kenai Watershed Forum, (2) Seward harbor soundings from the U.S. Army Corp of Engineers, and (3) multibeam bathymetry from the National Oceanic and Atmospheric Administration contributed to the final combined product. These datasets were placed into a common coordinate system, horizontal datum, vertical datum, and data format prior to being combined. The projected coordinate system of Universal Transverse Mercator Zone 6 North American Datum of 1927 was used for the horizontal coordinates. Z-values in meters were referenced to the tidal datum of Mean High Water. Gaps between the datasets were interpolated to create the final seamless 5-meter grid covering the area of interest around Seward, Alaska.

Determinación astronómica de la Desviación de la Vertical

NASA Astrophysics Data System (ADS)

Pacheco, A. M.; Podestá, R. C.

A partir de las coordenadas astronómicas de Latitud y Longitud determinadas en la falla geológica de Nikizanga ubicada en las serranías de Pie de Palo, y, en base a un Punto Datum de referencia, se desarrolla la metodología para la determinación de la Desviación de la Vertical, que comprende la reducción de las observaciones astronómicas, transformaciones de coordenadas, aplicación de correcciones y el cálculo definitivo de los valores angulares de la Vertical. Estos estudios se iniciaron a sugerencia del Servicio Internacional de Latitud, International Polar Motion Service (IPMS), con el objeto de obtener en determinados puntos de la Tierra la Desviación de la Vertical y su variación, dentro de la nueva disciplina denominada Astrogeodinámica, con la idea de correlacionar estas variaciones con la predicción de grandes sismos.

78 FR 36571 - North American Datum of 1983 (NAD 83) Outer Continental Shelf (OCS) Provisional Official...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-18

... DEPARTMENT OF THE INTERIOR Bureau of Ocean Energy Management [MMAA104000] North American Datum of 1983 (NAD 83) Outer Continental Shelf (OCS) Provisional Official Protraction Diagram (OPDs) AGENCY... OPDs. SUMMARY: Notice is hereby given that effective with this publication two NAD 83-based OCS...

Accuracy assessment of the U.S. Geological Survey National Elevation Dataset, and comparison with other large-area elevation datasets: SRTM and ASTER

USGS Publications Warehouse

Gesch, Dean B.; Oimoen, Michael J.; Evans, Gayla A.

2014-01-01

The National Elevation Dataset (NED) is the primary elevation data product produced and distributed by the U.S. Geological Survey. The NED provides seamless raster elevation data of the conterminous United States, Alaska, Hawaii, U.S. island territories, Mexico, and Canada. The NED is derived from diverse source datasets that are processed to a specification with consistent resolutions, coordinate system, elevation units, and horizontal and vertical datums. The NED serves as the elevation layer of The National Map, and it provides basic elevation information for earth science studies and mapping applications in the United States and most of North America. An important part of supporting scientific and operational use of the NED is provision of thorough dataset documentation including data quality and accuracy metrics. The focus of this report is on the vertical accuracy of the NED and on comparison of the NED with other similar large-area elevation datasets, namely data from the Shuttle Radar Topography Mission (SRTM) and the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER).

78 FR 5798 - Ceresco Hydroelectric Dam, LLC; Notice of Preliminary Permit Application Accepted for Filing and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-01-28

... Hydroelectric Dam, LLC; Notice of Preliminary Permit Application Accepted for Filing and Soliciting Comments, Motions To Intervene, and Competing Applications On October 19, 2012, Ceresco Hydroelectric Dam, LLC... feet National Geodetic Vertical Datum; (2) a dam comprised of (a) a 126- foot-wide, 13-foot-high...

77 FR 45262 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-31

... upstream of the upstream Grundy County, Village side of the Dresden of Channahon. Island Lock and Dam.... Just downstream of the +507 Dresden Island Lock and Dam. * National Geodetic Vertical Datum. + North... available for inspection at the North Moreland Township Municipal Building, 15 Municipal Lane, Dallas, PA...

77 FR 20999 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-09

... set forth below: * Elevation in feet (NGVD) + Elevation in feet (NAVD) Depth in feet Flooding source(s..., and Incorporated Areas Docket No.: FEMA-B-1100 Mississippi River Approximately 11.2 miles +585 City of.... Approximately 12.8 miles +594 upstream of State Highway 136. * National Geodetic Vertical Datum. + North...

78 FR 43821 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-22

............ +902 Unincorporated Areas of LaGrange County. Big Long Lake Entire shoreline......... +957 Unincorporated Areas of LaGrange County. Big Turkey Lake Entire shoreline within +932 Unincorporated Areas of... Vertical Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level...

78 FR 76604 - Grand River Dam Authority; Notice of Application Tendered for Filing With the Commission and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-18

... reservoir for the Grand River Dam Authority's Markham Ferry Project No. 2183, for pumped storage operations.... Holway Reservoir (the upper reservoir), with a normal pool elevation between 850 feet and 865 feet National Geodetic Vertical Datum; (2) three rim dikes around the upper reservoir; (3) an 1,800-foot-long...

National Elevation Dataset

USGS Publications Warehouse

,

2002-01-01

The National Elevation Dataset (NED) is a new raster product assembled by the U.S. Geological Survey. NED is designed to provide National elevation data in a seamless form with a consistent datum, elevation unit, and projection. Data corrections were made in the NED assembly process to minimize artifacts, perform edge matching, and fill sliver areas of missing data. NED has a resolution of one arc-second (approximately 30 meters) for the conterminous United States, Hawaii, Puerto Rico and the island territories and a resolution of two arc-seconds for Alaska. NED data sources have a variety of elevation units, horizontal datums, and map projections. In the NED assembly process the elevation values are converted to decimal meters as a consistent unit of measure, NAD83 is consistently used as horizontal datum, and all the data are recast in a geographic projection. Older DEM's produced by methods that are now obsolete have been filtered during the NED assembly process to minimize artifacts that are commonly found in data produced by these methods. Artifact removal greatly improves the quality of the slope, shaded-relief, and synthetic drainage information that can be derived from the elevation data. Figure 2 illustrates the results of this artifact removal filtering. NED processing also includes steps to adjust values where adjacent DEM's do not match well, and to fill sliver areas of missing data between DEM's. These processing steps ensure that NED has no void areas and artificial discontinuities have been minimized. The artifact removal filtering process does not eliminate all of the artifacts. In areas where the only available DEM is produced by older methods, then "striping" may still occur.

Options for developing modernized geodetic datum for Nepal following the April 25, 2015 Mw7.8 Gorkha earthquake

NASA Astrophysics Data System (ADS)

Pearson, Chris; Manandhar, Niraj; Denys, Paul

2017-09-01

Along with the damage to buildings and infrastructure, the April 25, 2015 Mw7.8 Gorkha earthquake caused significant deformation over a large area of eastern Nepal with displacements of over 2 m recorded in the vicinity of Kathmandu. Nepal currently uses a classical datum developed in 1984 by the Royal (UK) Engineers in collaboration with the Nepal Survey Department. It has served Nepal well; however, the recent earthquakes have provided an impetus for developing a semi-dynamic datum that will be based on ITRF2014 and have the capacity to correct for tectonic deformation. In the scenario we present here, the datum would be based on ITRF2014 with a reference epoch set some time after the end of the current sequence of earthquakes. The deformation model contains a grid of the secular velocity field combined with models of the Gorkha Earthquake and the May 12 Mw7.3 aftershock. We have developed a preliminary velocity field by collating GPS derived crustal velocities from four previous studies for Nepal and adjacent parts of China and India and aligning them to the ITRF. Patches for the co-seismic part of the deformation for the Gorkha earthquake and the May 12, 2015 Mw 7.2 aftershock are based on published dislocation models. High order control would be a CORS network based around the existing Nepal GPS Array. Coordinates for existing lower order control would be determined by readjusting existing survey measurements and these would be combined with a series of new control stations spread throughout Nepal.

76 FR 13569 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-14

..., FEMA published in the Federal Register a proposed rule that included erroneous Base Flood Elevation... for the proposed BFE of 1,290 feet, referenced to the North American Vertical Datum of 1988, should... Vertical Datum of 1988, should have located the proposed BFE as being approximately 0.24 mile upstream of...

76 FR 14359 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-16

..., FEMA published in the Federal Register a proposed rule that included erroneous Base Flood Elevation... description for the proposed BFE of 1,032 feet, referenced to the North American Vertical Datum of 1988... description for the proposed BFE of 1,049 feet, referenced to the North American Vertical Datum of 1988...

Topobathymetric model of Mobile Bay, Alabama

USGS Publications Warehouse

Danielson, Jeffrey J.; Brock, John C.; Howard, Daniel M.; Gesch, Dean B.; Bonisteel-Cormier, Jamie M.; Travers, Laurinda J.

2013-01-01

Topobathymetric Digital Elevation Models (DEMs) are a merged rendering of both topography (land elevation) and bathymetry (water depth) that provides a seamless elevation product useful for inundation mapping, as well as for other earth science applications, such as the development of sediment-transport, sea-level rise, and storm-surge models. This 1/9-arc-second (approximately 3 meters) resolution model of Mobile Bay, Alabama was developed using multiple topographic and bathymetric datasets, collected on different dates. The topographic data were obtained primarily from the U.S. Geological Survey (USGS) National Elevation Dataset (NED) (http://ned.usgs.gov/) at 1/9-arc-second resolution; USGS Experimental Advanced Airborne Research Lidar (EAARL) data (2 meters) (http://pubs.usgs.gov/ds/400/); and topographic lidar data (2 meters) and Compact Hydrographic Airborne Rapid Total Survey (CHARTS) lidar data (2 meters) from the U.S. Army Corps of Engineers (USACE) (http://www.csc.noaa.gov/digitalcoast/data/coastallidar/). Bathymetry was derived from digital soundings obtained from the National Oceanic and Atmospheric Administration’s (NOAA) National Geophysical Data Center (NGDC) (http://www.ngdc.noaa.gov/mgg/geodas/geodas.html) and from water-penetrating lidar sources, such as EAARL and CHARTS. Mobile Bay is ecologically important as it is the fourth largest estuary in the United States. The Mobile and Tensaw Rivers drain into the bay at the northern end with the bay emptying into the Gulf of Mexico at the southern end. Dauphin Island (a barrier island) and the Fort Morgan Peninsula form the mouth of Mobile Bay. Mobile Bay is 31 miles (50 kilometers) long by a maximum width of 24 miles (39 kilometers) with a total area of 413 square miles (1,070 square kilometers). The vertical datum of the Mobile Bay topobathymetric model is the North American Vertical Datum of 1988 (NAVD 88). All the topographic datasets were originally referenced to NAVD 88 and no transformations

Multi-Terrain Vertical Drop Tests of a Composite Fuselage Section

NASA Technical Reports Server (NTRS)

Kellas, Sotiris; Jackson, Karen E.

2008-01-01

A 5-ft-diameter composite fuselage section was retrofitted with four identical blocks of deployable honeycomb energy absorber and crash tested on two different surfaces: soft soil, and water. The drop tests were conducted at the 70-ft. drop tower at the Landing and Impact Research (LandIR) Facility of NASA Langley. Water drop tests were performed into a 15-ft-diameter pool of water that was approximately 42-in. deep. For the soft soil impact, a 15-ft-square container filled with fine-sifted, unpacked sand was located beneath the drop tower. All drop tests were vertical with a nominally flat attitude with respect to the impact surface. The measured impact velocities were 37.4, and 24.7-fps for soft soil and water, respectively. A fuselage section without energy absorbers was also drop tested onto water to provide a datum for comparison with the test, which included energy absorbers. In order to facilitate this type of comparison and to ensure fuselage survivability for the no-energy-absorber case, the velocity of the water impact tests was restricted to 25-fps nominal. While all tests described in this paper were limited to vertical impact velocities, the implications and design challenges of utilizing external energy absorbers during combined forward and vertical impact velocities are discussed. The design, testing and selection of a honeycomb cover, which was required in soft surface and water impacts to transmit the load into the honeycomb cell walls, is also presented.

Dynamic Heights in the Great Lakes using OPUS Projects

NASA Astrophysics Data System (ADS)

Roman, D. R.; Li, X.

2015-12-01

The U.S. will be implementing new geometric and vertical reference frames in 2022 to replace the North American Datum of 1983 (NAD 83) and the North American Vertical Datum of 1988 (NAVD 88), respectively. Less emphasized is the fact that a new dynamic height datum will also be defined about the same time to replace the International Great Lakes Datum of 1985 (IGLD 85). IGLD 85 was defined concurrent with NAVD 88 and used the same geopotential values. This paper focuses on the use of an existing tool for determining geometric coordinates and a developing geopotential model as a means of determining dynamic heights. The Online Positioning User Service (OPUS) Projects (OP) is an online tool available from the National Geodetic Survey (NGS) for use in developing geometric coordinates from simultaneous observations at multiple sites during multiple occupations. With observations performed at the water level gauges throughout the Great Lakes, the geometric coordinates of the mean water level surface can be determined. NGS has also developed the xGEOID15B model from satellite, airborne and surface gravity data. Using the input geometric coordinates determined through OP, the geopotential values for the water surface at the water level stations around the Great Lakes were determined using the xGEOID15B model. Comparisons were made between water level sites for each Lake as well as to existing IGLD 85 heights. A principal advantage to this approach is the ability to generate new water level control stations using OP, while maintaining the consistency between orthometric and dynamic heights by using the same gravity field model. Such a process may provide a means for determining dynamic heights for a future Great Lakes Datum.

Simulator Design and Instructional Features for Carrier Landing: A Field Transfer Study

DTIC Science & Technology

1986-06-18

the datum bars. This light is known as the meatball . It is visible to the pilot through the center lens and is seen as level with the datum bars when... meatball is seen through higher or lower Fresnel lenses to give the appearance of moving vertically above or below the line of the datum bars Figure A-i...degrees) by keeping the meatball level with the datum bars, so that a hook attached to the ý:ail of the aircraft will contact the landing deck midway

Consideration of vertical uncertainty in elevation-based sea-level rise assessments: Mobile Bay, Alabama case study

USGS Publications Warehouse

Gesch, Dean B.

2013-01-01

The accuracy with which coastal topography has been mapped directly affects the reliability and usefulness of elevationbased sea-level rise vulnerability assessments. Recent research has shown that the qualities of the elevation data must be well understood to properly model potential impacts. The cumulative vertical uncertainty has contributions from elevation data error, water level data uncertainties, and vertical datum and transformation uncertainties. The concepts of minimum sealevel rise increment and minimum planning timeline, important parameters for an elevation-based sea-level rise assessment, are used in recognition of the inherent vertical uncertainty of the underlying data. These concepts were applied to conduct a sea-level rise vulnerability assessment of the Mobile Bay, Alabama, region based on high-quality lidar-derived elevation data. The results that detail the area and associated resources (land cover, population, and infrastructure) vulnerable to a 1.18-m sea-level rise by the year 2100 are reported as a range of values (at the 95% confidence level) to account for the vertical uncertainty in the base data. Examination of the tabulated statistics about land cover, population, and infrastructure in the minimum and maximum vulnerable areas shows that these resources are not uniformly distributed throughout the overall vulnerable zone. The methods demonstrated in the Mobile Bay analysis provide an example of how to consider and properly account for vertical uncertainty in elevation-based sea-level rise vulnerability assessments, and the advantages of doing so.

Ellipsoidal Harmonic Vertical Deflections. Global and Regional Modeling of The Horizontal Derivative of The Terrestrial Garvity Field

NASA Astrophysics Data System (ADS)

Grafarend, E. W.; Ardalan, A.; Finn, G.

In terms of elliptic coordinates of Jacobi type (longitude, latitude, semi-minor axis) the horizontal derivative is computed as a linear operator acting on an ellipsoidal har- monic disturbing/incremental gravitational potential. Such disturbing potential is de- fined with respect to the Somigliana-Pizzetti Reference Potential, the potential field of a level ellipsoid, and the International Reference Ellipsoid/WGS84 or World Geode- tic Datum 2000/WGD2000. Case studies of those vertical deflections on a global as well as regional scale are presented which take advantage of SEGEN (Special Ellipsoidal Gravity Earth Normal: ellipsoidal harmonics expansion 130321 coeffi- cients: http://www.uni-stuttgart.de/gi/research/paper/coefficients/coefficients.zip) and of CENT (precise centrifugal potential)

Vertical Accuracy Assessment of ZY-3 Digital Surface Model Using Icesat/glas Laser Altimeter Data

NASA Astrophysics Data System (ADS)

Li, G.; Tang, X.; Yuan, X.; Zhou, P.; Hu, F.

2017-05-01

The Ziyuan-3 (ZY-3) satellite, as the first civilian high resolution surveying and mapping satellite in China, has a very important role in national 1 : 50,000 stereo mapping project. High accuracy digital surface Model (DSMs) can be generated from the three line-array images of ZY-3, and ZY-3 DSMs of China can be produced without using any ground control points (GCPs) by selecting SRTM (Shuttle Radar Topography Mission) and ICESat/GLAS (Ice, Cloud, and land Elevation Satellite, Geo-science Laser Altimeter System) as the datum reference in the Satellite Surveying and Mapping Application Center, which is the key institute that manages and distributes ZY-3 products. To conduct the vertical accuracy evaluation of ZY-3 DSMs of China, three representative regions were chosen and the results were compared to ICESat/GLAS data. The experimental results demonstrated that the root mean square error (RMSE) elevation accuracy of the ZY-3 DSMs was better than 5.0 m, and it even reached to less than 2.5 m in the second region of eastern China. While this work presents preliminary results, it is an important reference for expanding the application of ZY-3 satellite imagery to widespread regions. And the satellite laser altimetry data can be used as referenced data for wide-area DSM evaluation.

Geoid Determination Using GOCE-Based Models in Turkey

NASA Astrophysics Data System (ADS)

Serkan Işık, Mustafa; Erol, Bihter

2016-04-01

The maintenance of the vertical datum in tectonically active regions such as Turkey become more of an issue. The distortions in the vertical datum due to geodynamic phenomena necessitate the realization of geoid based vertical datum. The height modernization studies for transition to a "geoid based vertical datum definition" providing practical use of GNSS technologies to obtain orthometric heights in Turkey has accelerated rapidly in recent years and hence in the content of these efforts on-going projects contribute to improvement of quality and quantity of terrestrial gravity dataset as well as selection of the optimal computation algorithm to reach a precise geoid model in the territory. In this manner the assessment of the different methodologies with varying input parameters and referred models is obviously essential to in order to clarify the advantages of the algorithms in terms of providing an optimal combination of different data sets in regional geoid modeling. The performance of recently published GOCE-GRACE gravity field models show significant improvements in the medium frequency. This study investigates the contribution of the recently released Geopotential models with the contribution of GOCE and GRACE missions to the gravimetric geoid modeling specifically from Least squares modification of Stokes' (LSMS) formula point of view in Turkey territory. The algorithm developed by Royal Institute of Technology (KTH) that adopt the least squares modification of Stokes' kernel in order for providing an optimum combination of spherical harmonic expansion model and terrestrial gravity data and hence claims to optimize the drawbacks, may stem from the handicaps (such as low accuracy, sparse distribution etc.) of the terrestrial gravity data in the results. The additive corrective terms in order to account for downward continuation effect, atmospheric effect and ellipsoidal effect are proposed as the superiorities of this algorithm comparing to the conventional

76 FR 62006 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-06

... Sea Level, rounded to the nearest 0.1 meter. ** BFEs to be changed include the listed downstream and... above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ** BFEs to be changed include... Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to...

76 FR 46705 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-08-03

... ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ** BFEs to be changed include the.... Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ** BFEs to be... Datum. + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to...

Levels at Streamflow Gaging Stations--A CD-ROM Based Training Class

USGS Publications Warehouse

Nolan, K. Michael; Jacobson, Nathan; Erickson, Robert; Landon, Stanley

2003-01-01

Streamgages record the elevation of the water surface above some reference surface, or datum. This datum is assumed to remain unchanged throughout the life of the gage. However, the elevation of gages and their supporting structures often change over time as a result of earthmovement, floods, ice, and debris. The surveying practice of leveling is used to establish datum for new gage structures and to check for vertical movement of those structures over time. Vertical changes in gage structures can affect stage-discharge relations and, thus, could result in incorrect discharge determinations. Datum checks are used to correct stage-discharge relations and allow the USGS to document gage datum throughout the life of a gage. This training presentation describes methods currently used by the U.S. Geological Survey to run levels at gaging stations. The presentation is narrated, but you control the pace of the presentation. If the computer you are using can view 'MPEG' videos you will be able to take advantage of videos found within the presentation. A test, found at the end of the presentation, can be taken to assess how well you understood the training material. The class is registered as class SW1307 with the National Training Center of the U.S. Geologcial Survey. The presentation was developed using Macromedia Director 8.5(1) and is contained in the file 'WRI-4002.exe', which should auto-launch after the CD-ROM is inserted in the PC. The program only runs on a windows-based personal computer (PC). A sound card and speakers are necessary to take advantage of the narration that accompanies the presentation. Text of narrations is provided, if you are unable to listen to the narrations. Instructions for installing and running the presentation are included in the file ' Intro.html'. The file 'Intro.html' is on the CD-ROM containing the presentation and is available from the presentation's help menu.

Satellite altimetry and GOCE contribution to the pre-definition of the Kingdom of Saudi Arabia (KSA) Vertical Network

NASA Astrophysics Data System (ADS)

Vergos, Georgios S.; Grebenitcharsky, Rossen S.; Natsiopoulos, Dimitrios A.; Al-Kherayef, Othman; Al-Muslmani, Bandar

2017-04-01

The availability of a unified and well-established national vertical system and frame is of outmost importance in support of everyday geodetic, surveying and engineering applications. Vertical reference system (VRS) modernization and unification has gained increased importance especially during the last years due to the advent of gravity-field dedicated missions and GOCE in particular, since it is the first time that an unprecedented in accuracy dataset of gravity field functionals has become available at a global scale. The Kingdom of Saudi Arabia VRS is outdated and exhibits significant tilts and biases, so that during the last couple of years an extensive effort has been put forth in order to: re-measure by traditional levelling the entire network, establish new benchmarks (BMs), perform high-quality absolute and relative gravity observations and construct new tide-gauge (TG) stations in both the Arab and Red Seas. The Current work focuses on the combined analysis of the existing, recently collected, terrestrial observations with satellite altimetry data and the latest GOCE-based Earth Geopotential Models (EGMs) in order to provide a pre-definition of the KSA VRS. To that respect, a 30-year satellite altimetry time-series is constructed for each TG station in order to derive both the Mean Sea Level (MSL) as well as the sea level trends. This information is analyzed, through Wavelet (WL) Multi-resolution Analysis (MRA), with the TG sea level records in order to determine annual, semi-annual and secular trends of the Red and Arab Sea variations. Finally, the so-derived trends and MSL are combined with local gravity observations at the TG BMs, levelling offsets between the TGs and the network BMs, levelling observations between the network BMs themselves and GOCE-based EGM-derived geoid heights and potential values. The validation of GOCE contribution and of the satellite altimetry derived MSL and trends is based on a simultaneous adjustment of the entire KSA

High-water marks from flooding in Lake Champlain from April through June 2011 and Tropical Storm Irene in August 2011 in Vermont

USGS Publications Warehouse

Medalie, Laura; Olson, S.A.

2013-01-01

The U.S. Geological Survey, in cooperation with the Federal Emergency Management Agency, identified high-water marks after two floods in Vermont during 2011. Following a snowy winter, new monthly precipitation records were set in Burlington, Vermont, in April and May 2011, causing extensive flooding from April through June. The spring 2011 flooding resulted in a new record for stage (103.27 feet, referenced to the National Geodetic Vertical Datum of 1929) at the Lake Champlain at Burlington, Vt., gaging station (04294500). During August 28 and 29, 2011, tropical storm Irene delivered rainfall totals of 3 to more than 7 inches throughout Vermont, which resulted in extensive flooding and new streamflow records at nine streamgaging stations. Four presidential declarations of disaster were made following the 2011 flood events in Vermont. Thirty-nine high-water marks were identified and flagged to mark the highest levels of Lake Champlain from the May 2011 flooding, and 1,138 high-water marks were identified and flagged along Vermont rivers after flooding from tropical storm Irene in August 2011. Seventy-four percent of the high-water marks that were flagged were later found and surveyed to the North American Vertical Datum of 1988.

New Orleans, LA, District: Report of the Secretary of the Army on Civil Works Activities for FY 2011

DTIC Science & Technology

2011-01-01

side slopes, and protective vegetation. The sandfill berm slopes from an elevation of 8.5 feet, NGVD, at the toe of the dune 150 feet gulfward to an...and vegetated dune constructive with a geotextile tube core extending the length of Grand Isle’s gulf shore and a jetty to stabilize the western end...of the island at Caminada Pass. The dune has a 10-foot-wide crown at an elevation of 13.5 feet, National Geodetic Vertical Datum (NGVD), 1 on 5

KNGEOID14: A national hybrid geoid model in Korea

NASA Astrophysics Data System (ADS)

Kang, S.; Sung, Y. M.; KIM, H.; Kim, Y. S.

2016-12-01

This study describes in brief the construction of a national hybrid geoid model in Korea, KNGEOID14, which can be used as an accurate vertical datum in/around Korea. The hybrid geoid model should be determined by fitting the gravimetric geoid to the geometric geoid undulations from GNSS/Leveling data which were presented the local vertical level. For developing the gravimetric geoid model, we determined all frequency parts (long, middle and short-frequency) of gravimetric geoid using all available data with optimal remove-restore technique based on EGM2008 reference surface. In remove-restore technique, the EGM2008 model to degree 360, RTM reduction method were used for calculating the long, middle and short-frequency part of gravimetric geoid, respectively. A number of gravity data compiled for modeling the middle-frequency part, residual geoid, containing 8,866 points gravity data on land and ocean areas. And, the DEM data gridded by 100m×100m were used for short-frequency part, is the topographic effect on the geoid generated by RTM method. The accuracy of gravimetric geoid model were evaluated by comparison with GNSS/Leveling data was about -0.362m ± 0.055m. Finally, we developed the national hybrid geoid model in Korea, KNGEOID14, corrected to gravimetric geoid with the correction term by fitting the about 1,200 GNSS/Leveling data on Korean bench marks. The correction term is modeled using the difference between GNSS/Leveling derived geoidal heights and gravimetric geoidal heights. The stochastic model used in the calculation of correction term is the LSC technique based on second-order Markov covariance function. The post-fit error (mean and std. dev.) of the KNGEOID14 model was evaluated as 0.001m ± 0.033m. Concerning the result of this study, the accurate orthometric height at any points in Korea will be easily and precisely calculated by combining the geoidal height from KNGEOID14 and ellipsoidal height from GPS observation technique.

Accuracy assessment of a mobile terrestrial lidar survey at Padre Island National Seashore

USGS Publications Warehouse

Lim, Samsung; Thatcher, Cindy A.; Brock, John C.; Kimbrow, Dustin R.; Danielson, Jeffrey J.; Reynolds, B.J.

2013-01-01

The higher point density and mobility of terrestrial laser scanning (light detection and ranging (lidar)) is desired when extremely detailed elevation data are needed for mapping vertically orientated complex features such as levees, dunes, and cliffs, or when highly accurate data are needed for monitoring geomorphic changes. Mobile terrestrial lidar scanners have the capability for rapid data collection on a larger spatial scale compared with tripod-based terrestrial lidar, but few studies have examined the accuracy of this relatively new mapping technology. For this reason, we conducted a field test at Padre Island National Seashore of a mobile lidar scanner mounted on a sport utility vehicle and integrated with a position and orientation system. The purpose of the study was to assess the vertical and horizontal accuracy of data collected by the mobile terrestrial lidar system, which is georeferenced to the Universal Transverse Mercator coordinate system and the North American Vertical Datum of 1988. To accomplish the study objectives, independent elevation data were collected by conducting a high-accuracy global positioning system survey to establish the coordinates and elevations of 12 targets spaced throughout the 12 km transect. These independent ground control data were compared to the lidar scanner-derived elevations to quantify the accuracy of the mobile lidar system. The performance of the mobile lidar system was also tested at various vehicle speeds and scan density settings (e.g. field of view and linear point spacing) to estimate the optimal parameters for desired point density. After adjustment of the lever arm parameters, the final point cloud accuracy was 0.060 m (east), 0.095 m (north), and 0.053 m (height). The very high density of the resulting point cloud was sufficient to map fine-scale topographic features, such as the complex shape of the sand dunes.

Assessing New GRAV-D Airborne Gravimetry Collected over the United States

NASA Astrophysics Data System (ADS)

Holmes, S. A.; Li, X.; Roman, D. R.

2013-12-01

The U.S. National Geodetic Survey [NGS], through their Gravity for the Redefinition of the American Vertical Datum [GRAV-D] program, is updating its terrestrial gravimetry holdings by flying new airborne gravity surveys over a large fraction of the USA and its territories. By 2020, NGS intends that all orthometric heights in the USA will be determined in the field by using a reliable national gravimetric geoid model to transform from geodetic heights obtained from GPS. Towards this end, the newly-collected airborne-gravimety is repeatedly evaluated by using it to support experimental gravitational models and gravimetric geoids, and then comparing these against independent data sets, such as ';satgrav' models (GRACE/GOCE), GPS/Leveling, astronomical vertical defections, and others. Here we show some results from these tests for GRAV-D airborne gravimetry collected over 2012/2013.

Moving to a Modernized Height Reference System in Canada: Rationale, Status and Plans

NASA Astrophysics Data System (ADS)

Veronneau, M.; Huang, J.

2007-05-01

A modern society depends on a common coordinate reference system through which geospatial information can be interrelated and exploited reliably. For height measurements this requires the ability to measure mean sea level elevations easily, accurately, and at the lowest possible cost. The current national reference system for elevations, the Canadian Geodetic Vertical Datum of 1928 (CGVD28), offers only partial geographic coverage of the Canadian territory and is affected by inaccuracies that are becoming more apparent as users move to space- based technologies such as GPS. Furthermore, the maintenance and expansion of the national vertical network using spirit-levelling, a costly, time consuming and labour intensive proposition, has only been minimally funded over the past decade. It is now generally accepted that the most sustainable alternative for the realization of a national vertical datum is a gravimetric geoid model. This approach defines the datum in relation to an ellipsoid, making it compatible with space-based technologies for positioning. While simplifying access to heights above mean sea level all across the Canadian territory, this approach imposes additional demands on the quality of the geoid model. These are being met by recent and upcoming space gravimetry missions that have and will be measuring the Earth`s gravity field with increasing and unprecedented accuracy. To maintain compatibility with the CGVD28 datum materialized at benchmarks, the current first-order levelling can be readjusted by constraining geoid heights at selected stations of the Canadian Base Network. The new reference would change CGVD28 heights of benchmarks by up to 1 m across Canada. However, local height differences between benchmarks would maintain a relative precision of a few cm or better. CGVD28 will co-exist with the new height reference as long as it will be required, but it will undoubtedly disappear as benchmarks are destroyed over time. The adoption of GNSS

Potentiometric surface of the Catahoula aquifer in central Louisiana, 2013

USGS Publications Warehouse

Fendick, Jr., Robert B.; Carter, Kayla

2015-12-09

The potentiometric surface of the Catahoula aquifer was constructed by using the altitude of water levels measured at 29 wells during the period May through September 2013. The altitude of water levels ranged from 0.02 ft above the National Geodetic Vertical Datum of 1929 (NGVD 29) in well Co-51 to 238 ft above NGVD 29 in well Na-317. Groundwater movement in the Catahoula aquifer is generally to the southeast and towards discharge areas beneath the Sabine, Red, Little, and Tensas River Valleys.

Results from the ESA-funded project 'Height System Unification with GOCE'

NASA Astrophysics Data System (ADS)

Sideris, M. G.; Rangelova, E. V.; Gruber, T.; Rummel, R. F.; Woodworth, P. L.; Hughes, C. W.; Ihde, J.; Liebsch, G.; Schäfer, U.; Rülke, A.; Gerlach, C.; Haagmans, R.

2013-12-01

The paper summarizes the main results of a project, supported by the European Space Agency, whose main goal is to identify the impact of GOCE gravity field models on height system unification. In particular, the Technical University Munich, the University of Calgary and the National Oceanography Centre in Liverpool, together with the Bavarian Academy of Sciences, the Federal German Agency for Cartography and Geodesy, and the Geodetic Surveys of Canada, USA and Mexico, have investigated the role of GOCE-derived gravity and geoid models for regional and global height datum connection. GOCE provides three important components of height unification: highly accurate potential differences (geopotential numbers), a global geoid- or quasi-geoid-based reference surface for elevations that is independent of inaccuracies and inconsistencies of local and regional data, and a consistent way to refer to the same datum all the relevant gravimetric, topographic and oceanographic data. We introduce briefly the methodology that has been applied in order to unify height system in North America, North Atlantic Ocean and Europe, and present results obtained using the available GOCE-derived satellite-only geopotential models, and their combination with terrestrial data and ocean models. The effects of various factors, such as data noise, omission errors, indirect bias terms, ocean models and temporal variations, on height datum unification are also presented, highlighting their magnitude and importance in the estimation of offsets between vertical datums. Based on the experiences gained in this project, a general roadmap has been developed for height datum unification in regions with good, as well as poor, coverage in gravity and geodetic height and tide gauge control stations.

Construction of a 3-arcsecond digital elevation model for the Gulf of Maine

USGS Publications Warehouse

Twomey, Erin R.; Signell, Richard P.

2013-01-01

A system-wide description of the seafloor topography is a basic requirement for most coastal oceanographic studies. The necessary detail of the topography obviously varies with application, but for many uses, a nominal resolution of roughly 100 m is sufficient. Creating a digital bathymetric grid with this level of resolution can be a complex procedure due to a multiplicity of data sources, data coverages, datums and interpolation procedures. This report documents the procedures used to construct a 3-arcsecond (approximately 90-meter grid cell size) digital elevation model for the Gulf of Maine (71°30' to 63° W, 39°30' to 46° N). We obtained elevation and bathymetric data from a variety of American and Canadian sources, converted all data to the North American Datum of 1983 for horizontal coordinates and the North American Vertical Datum of 1988 for vertical coordinates, used a combination of automatic and manual techniques for quality control, and interpolated gaps using a surface-fitting routine.

77 FR 43063 - Affirmation of Vertical Datum for Surveying and Mapping Activities for the Territory of Puerto Rico

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-23

... National Water Level Observation Network (NWLON) for bench marks designated 975 5371 A TIDAL (PID TV1513) (1.334 meters), located at La Puntilla, San Juan Puerto Rico, 975 2235 D (PID DN8624) (0.973 meters), located on Culebra Island, 975 2695 A (PID DN8535) (1.962 meters), located at Esperanza, Vieques Island...

Datum maintenance of the main Egyptian geodetic control networks by utilizing Precise Point Positioning "PPP" technique

NASA Astrophysics Data System (ADS)

Rabah, Mostafa; Elmewafey, Mahmoud; Farahan, Magda H.

2016-06-01

A geodetic control network is the wire-frame or the skeleton on which continuous and consistent mapping, Geographic Information Systems (GIS), and surveys are based. Traditionally, geodetic control points are established as permanent physical monuments placed in the ground and precisely marked, located, and documented. With the development of satellite surveying methods and their availability and high degree of accuracy, a geodetic control network could be established by using GNSS and referred to an international terrestrial reference frame used as a three-dimensional geocentric reference system for a country. Based on this concept, in 1992, the Egypt Survey Authority (ESA) established two networks, namely High Accuracy Reference Network (HARN) and the National Agricultural Cadastral Network (NACN). To transfer the International Terrestrial Reference Frame to the HARN, the HARN was connected with four IGS stations. The processing results were 1:10,000,000 (Order A) for HARN and 1:1,000,000 (Order B) for NACN relative network accuracy standard between stations defined in ITRF1994 Epoch1996. Since 1996, ESA did not perform any updating or maintaining works for these networks. To see how non-performing maintenance degrading the values of the HARN and NACN, the available HARN and NACN stations in the Nile Delta were observed. The Processing of the tested part was done by CSRS-PPP Service based on utilizing Precise Point Positioning "PPP" and Trimble Business Center "TBC". The study shows the feasibility of Precise Point Positioning in updating the absolute positioning of the HARN network and its role in updating the reference frame (ITRF). The study also confirmed the necessity of the absent role of datum maintenance of Egypt networks.

Simultaneous observation solutions for NASA-MOTS and SPEOPT station positions on the North American datum

NASA Technical Reports Server (NTRS)

Reece, J. S.; Marsh, J.

1973-01-01

Simultaneous observations of the GEOS-I and II flashing lamps by the NASA MOTS and SPEOPT cameras on the North American Datum (NAD) were analyzed using geometrical techniques to provide an adjustment of the station coordinates. Two separate adjustments were obtained. An optical data only solution was computed in which the solution scale was provided by the Rosman-Mojave distance obtained from a dynamic station solution. In a second adjustment, scaling was provided by processing simultaneous laser ranging data from Greenbelt and Wallops Island in a combined optical-laser solution. Comparisons of these results with previous GSFC dynamical solutions indicate an rms agreement on the order of 4 meters or better in each coordinate. Comparison with a detailed gravimetric geoid of North America yields agreement of 3 meters or better for mainland U.S. stations and 7 and 3 meters, respectively, for Bermuda and Puerto Rico.

Sabkha Trafficability,

DTIC Science & Technology

1981-01-01

Meteorological Parameters at Meteorological Station 1, 31 May 1980 ........................ 68 $24 Relationship of Jubai. Port Datum to Tide Table Datum. .70 25...around which was a circular weight with two handles. Once assembled, the device was nositioned vertically at the point to be sampled and manually...limited use for sampling very fluid or unconsolidated sand or shell. In the former case, the upper few centimeters of cohesive sediment became embedded

National assessment of shoreline change—Summary statistics for updated vector shorelines and associated shoreline change data for the Gulf of Mexico and Southeast Atlantic coasts

USGS Publications Warehouse

Himmelstoss, Emily A.; Kratzmann, Meredith G.; Thieler, E. Robert

2017-07-18

Long-term rates of shoreline change for the Gulf of Mexico and Southeast Atlantic regions of the United States have been updated as part of the U.S. Geological Survey’s National Assessment of Shoreline Change project. Additional shoreline position data were used to compute rates where the previous rate-of-change assessment only included four shoreline positions at a given location. The long-term shoreline change rates also incorporate the proxy-datum bias correction to account for the unidirectional onshore bias of the proxy-based high water line shorelines relative to the datum-based mean high water shorelines. The calculation of uncertainty associated with the long-term average rates has also been updated to match refined methods used in other study regions of the National Assessment project. The average rates reported here have a reduced amount of uncertainty relative to those presented in the previous assessments for these two regions.

Prototype Evaluation of Sluiceway Aeration System Libby Dam, Kootenai River, Montana.

DTIC Science & Technology

1984-03-01

VICKSBURG MS H DRA.. R G MCGEE UNCLASSIFIED MAR 84 WES/TR/HL-84-2 F/G 13/13 NL- DE E-EullEI EEEEEIIIENEIII II I IE EEIImmiEmhihhhEEEI mEEmhEEihhEEm 1j...report of findings was published * All elevations ( el ) cited herein are in feet referred to the National Geodetic Vertical Datum (NGVD). 6 r.W (Hart...1981). Data derived from the test program were used as criteria for de - sign of a more efficient air vent system. 6. The resulting modification to the

Height system unification based on the Fixed Geodetic Boundary Value Problem with limited availability of gravity data

NASA Astrophysics Data System (ADS)

Porz, Lucas; Grombein, Thomas; Seitz, Kurt; Heck, Bernhard; Wenzel, Friedemann

2017-04-01

Regional height reference systems are generally related to individual vertical datums defined by specific tide gauges. The discrepancies of these vertical datums with respect to a unified global datum cause height system biases that range in an order of 1-2 m at a global scale. One approach for unification of height systems relates to the solution of a Geodetic Boundary Value Problem (GBVP). In particular, the fixed GBVP, using gravity disturbances as boundary values, is solved at GNSS/leveling benchmarks, whereupon height datum offsets can be estimated by least squares adjustment. In spherical approximation, the solution of the fixed GBVP is obtained by Hotine's spherical integral formula. However, this method relies on the global availability of gravity data. In practice, gravity data of the necessary resolution and accuracy is not accessible globally. Thus, the integration is restricted to an area within the vicinity of the computation points. The resulting truncation error can reach several meters in height, making height system unification without further consideration of this effect unfeasible. This study analyzes methods for reducing the truncation error by combining terrestrial gravity data with satellite-based global geopotential models and by modifying the integral kernel in order to accelerate the convergence of the resulting potential. For this purpose, EGM2008-derived gravity functionals are used as pseudo-observations to be integrated numerically. Geopotential models of different spectral degrees are implemented using a remove-restore-scheme. Three types of modification are applied to the Hotine-kernel and the convergence of the resulting potential is analyzed. In a further step, the impact of these operations on the estimation of height datum offsets is investigated within a closed loop simulation. A minimum integration radius in combination with a specific modification of the Hotine-kernel is suggested in order to achieve sub-cm accuracy for the

Analysis of vertical stability limits and vertical displacement event behavior on NSTX-U

NASA Astrophysics Data System (ADS)

Boyer, Mark; Battaglia, Devon; Gerhardt, Stefan; Menard, Jonathan; Mueller, Dennis; Myers, Clayton; Sabbagh, Steven; Smith, David

2017-10-01

The National Spherical Torus Experiment Upgrade (NSTX-U) completed its first run campaign in 2016, including commissioning a larger center-stack and three new tangentially aimed neutral beam sources. NSTX-U operates at increased aspect ratio due to the larger center-stack, making vertical stabilization more challenging. Since ST performance is improved at high elongation, improvements to the vertical control system were made, including use of multiple up-down-symmetric flux loop pairs for real-time estimation, and filtering to remove noise. Similar operating limits to those on NSTX (in terms of elongation and internal inductance) were achieved, now at higher aspect ratio. To better understand the observed limits and project to future operating points, a database of vertical displacement events and vertical oscillations observed during the plasma current ramp-up on NSTX/NSTX-U has been generated. Shots were clustered based on the characteristics of the VDEs/oscillations, and the plasma parameter regimes associated with the classes of behavior were studied. Results provide guidance for scenario development during ramp-up to avoid large oscillations at the time of diverting, and provide the means to assess stability of target scenarios for the next campaign. Results will also guide plans for improvements to the vertical control system. Work supported by U.S. D.O.E. Contract No. DE-AC02-09CH11466.

Water-Surface Elevations, Discharge, and Water-Quality Data for Selected Sites in the Warm Springs Area near Moapa, Nevada

USGS Publications Warehouse

Beck, David A.; Ryan, Roslyn; Veley, Ronald J.; Harper, Donald P.; Tanko, Daron J.

2006-01-01

The U.S. Geological Survey, in cooperation with Southern Nevada Water Authority and the Nevada Division of Water Resources, operates and maintains a surface-water monitoring network of 6 continuous-record stream-flow gaging stations and 11 partial-record stations in the Warm Springs area near Moapa, Nevada. Permanent land-surface bench marks were installed within the Warm Springs area by the Las Vegas Valley Water District, the Southern Nevada Water Authority, and the U.S. Geological Survey to determine water-surface elevations at all network monitoring sites. Vertical datum elevation and horizontal coordinates were established for all bench marks through a series of Differential Global Positioning System surveys. Optical theodolite surveys were made to transfer Differential Global Positioning System vertical datums to reference marks installed at each monitoring site. The surveys were completed in June 2004 and water-surface elevations were measured on August 17, 2004. Water-surface elevations ranged from 1,810.33 feet above North American Vertical Datum of 1988 at a stream-gaging station in the Pederson Springs area to 1,706.31 feet at a station on the Muddy River near Moapa. Discharge and water-quality data were compiled for the Warm Springs area and include data provided by the U.S. Geological Survey, Nevada Division of Water Resources, U.S. Fish and Wildlife Service, Moapa Valley Water District, Desert Research Institute, and Converse Consultants. Historical and current hydrologic data-collection networks primarily are related to changes in land- and water-use activities in the Warm Springs area. These changes include declines in ranching and agricultural use, the exportation of water to other areas of Moapa Valley, and the creation of a national wildlife refuge. Water-surface elevations, discharge, and water-quality data compiled for the Warm Springs area will help identify (1) effects of changing vegetation within the former agricultural lands, (2) effects

GRAV-D for Puerto Rico and the U.S. Virgin Islands

NASA Astrophysics Data System (ADS)

Roman, D. R.; Li, X.; Smith, D. A.; Geoid; GRAV-D Teams

2013-05-01

NOAA's National Geodetic Survey began the Gravity for the Redefinition of the American Vertical Datum (GRAV-D) program in an effort to modernize and unify vertical datums in all states and territories. As a part of this program, NGS collected aerogravity profiles over the islands of Puerto Rico and the U.S. Virgin Islands in January 2009. A Citation II aircraft was equipped with an airborne gravimeter, GPS receiver, and a GPS/Inertial unit. Absolute gravity and GPS ties were made to multiple ground sites to ensure consistency in the results. The main survey covered a region of approximately 400 km by 500 km with flight altitudes of 10,668 m (35,000ft) and with 10 km track spacing. Cross-track profiles at 40 km spacing were also collected to establish an accuracy of 1.34 mGals RMSE. In addition to the high altitude flights, two more flights were made primarily over terrestrial areas at 1,524 m (5,000 ft) to obtain higher resolution information in these regions. There were no cross-ties established for these lower altitude flights. Additionally, terrestrial surveys were also conducted to better tie ground sites and to serve as control for later analysis for available but older terrestrial and marine gravity data in the region already held by NGS. The aerogravity data were analyzed and at least internally compared to obtain the optimal results before being published on the web. In this study, the aerogravity data were compared to available global gravity models derived from satellite missions (GRACE & GOCE) to evaluate their long wavelength character (e.g., potential biases and trends). The vetted satellite-aerogravity data were then combined and used to evaluate surface data (terrestrial and marine) in the region to remove any potential systematic effects. Finally, all these data were combined into a gravimetric geoid height model and evaluated with an eye to eventual use as a GNSS-accessed vertical datum.

[Vertical distribution and community diversity of butterflies in Yaoluoping National Nature Reserve, Anhui, China].

PubMed

Wang, Song; Bao, Fang-yin; Mei, Bai-mao; Ding, Shi-chao

2009-09-01

By the methods of fixed point, line intercept, and random investigation, the vertical distribution and community diversity of butterflies in Yaoluoping National Nature Reserve were investigated from 2005 to 2008. A total of 3681 specimen were collected, belonging to 111 species, 69 genera, and 10 families, among which, Nymphalidae had the higher species number, individual's number, and diversity index than the other families. The butterflies in the study area were a mixture of Oriental and Palaearetic species, with the Oriental species diminished gradually and the Palaearetic components increased gradually with increasing altitude. Among the three vertical zones ( <800 m, 800-1200 m, and >1200 m in elevation), that of 800-1200 m had the most abundant species of butterflies; and among the six habitat types (deciduous broad-leaved forest, evergreen conifer forest, conifer-broad leaf mixed forest, bush and secondary forest, farmland, and residential area), bush and secondary forest had the higher species number, individual's number, and diversity index of butterflies, while farmland had the lowest diversity index. The similarity coefficient of butterfly species between the habitats was mainly dependent on vegetation type, i.e., the more the difference of vegetation type, the lesser the species similarity coefficient between the habitats, which was the highest (0.61) between conifer-broad leaf mixed forest and bush and secondary forest, and the lowest (0. 20) between evergreen conifer forest and bush and secondary forest.

Modelling the vertical distribution of canopy fuel load using national forest inventory and low-density airbone laser scanning data.

PubMed

González-Ferreiro, Eduardo; Arellano-Pérez, Stéfano; Castedo-Dorado, Fernando; Hevia, Andrea; Vega, José Antonio; Vega-Nieva, Daniel; Álvarez-González, Juan Gabriel; Ruiz-González, Ana Daría

2017-01-01

The fuel complex variables canopy bulk density and canopy base height are often used to predict crown fire initiation and spread. Direct measurement of these variables is impractical, and they are usually estimated indirectly by modelling. Recent advances in predicting crown fire behaviour require accurate estimates of the complete vertical distribution of canopy fuels. The objectives of the present study were to model the vertical profile of available canopy fuel in pine stands by using data from the Spanish national forest inventory plus low-density airborne laser scanning (ALS) metrics. In a first step, the vertical distribution of the canopy fuel load was modelled using the Weibull probability density function. In a second step, two different systems of models were fitted to estimate the canopy variables defining the vertical distributions; the first system related these variables to stand variables obtained in a field inventory, and the second system related the canopy variables to airborne laser scanning metrics. The models of each system were fitted simultaneously to compensate the effects of the inherent cross-model correlation between the canopy variables. Heteroscedasticity was also analyzed, but no correction in the fitting process was necessary. The estimated canopy fuel load profiles from field variables explained 84% and 86% of the variation in canopy fuel load for maritime pine and radiata pine respectively; whereas the estimated canopy fuel load profiles from ALS metrics explained 52% and 49% of the variation for the same species. The proposed models can be used to assess the effectiveness of different forest management alternatives for reducing crown fire hazard.

Modelling the vertical distribution of canopy fuel load using national forest inventory and low-density airbone laser scanning data

PubMed Central

Castedo-Dorado, Fernando; Hevia, Andrea; Vega, José Antonio; Vega-Nieva, Daniel; Ruiz-González, Ana Daría

2017-01-01

The fuel complex variables canopy bulk density and canopy base height are often used to predict crown fire initiation and spread. Direct measurement of these variables is impractical, and they are usually estimated indirectly by modelling. Recent advances in predicting crown fire behaviour require accurate estimates of the complete vertical distribution of canopy fuels. The objectives of the present study were to model the vertical profile of available canopy fuel in pine stands by using data from the Spanish national forest inventory plus low-density airborne laser scanning (ALS) metrics. In a first step, the vertical distribution of the canopy fuel load was modelled using the Weibull probability density function. In a second step, two different systems of models were fitted to estimate the canopy variables defining the vertical distributions; the first system related these variables to stand variables obtained in a field inventory, and the second system related the canopy variables to airborne laser scanning metrics. The models of each system were fitted simultaneously to compensate the effects of the inherent cross-model correlation between the canopy variables. Heteroscedasticity was also analyzed, but no correction in the fitting process was necessary. The estimated canopy fuel load profiles from field variables explained 84% and 86% of the variation in canopy fuel load for maritime pine and radiata pine respectively; whereas the estimated canopy fuel load profiles from ALS metrics explained 52% and 49% of the variation for the same species. The proposed models can be used to assess the effectiveness of different forest management alternatives for reducing crown fire hazard. PMID:28448524

Unification of height systems in the frame of GGOS

NASA Astrophysics Data System (ADS)

Sánchez, Laura

2015-04-01

Most of the existing vertical reference systems do not fulfil the accuracy requirements of modern Geodesy. They refer to local sea surface levels, are stationary (do not consider variations in time), realize different physical height types (orthometric, normal, normal-orthometric, etc.), and their combination in a global frame presents uncertainties at the metre level. To provide a precise geodetic infrastructure for monitoring the Earth system, the Global Geodetic Observing System (GGOS) of the International Association of Geodesy (IAG), promotes the standardization of the height systems worldwide. The main purpose is to establish a global gravity field-related vertical reference system that (1) supports a highly-precise (at cm-level) combination of physical and geometric heights worldwide, (2) allows the unification of all existing local height datums, and (3) guarantees vertical coordinates with global consistency (the same accuracy everywhere) and long-term stability (the same order of accuracy at any time). Under this umbrella, the present contribution concentrates on the definition and realization of a conventional global vertical reference system; the standardization of the geodetic data referring to the existing height systems; and the formulation of appropriate strategies for the precise transformation of the local height datums into the global vertical reference system. The proposed vertical reference system is based on two components: a geometric component consisting of ellipsoidal heights as coordinates and a level ellipsoid as the reference surface, and a physical component comprising geopotential numbers as coordinates and an equipotential surface defined by a conventional W0 value as the reference surface. The definition of the physical component is based on potential parameters in order to provide reference to any type of physical heights (normal, orthometric, etc.). The conversion of geopotential numbers into metric heights and the modelling of the

NASA directory of observation station locations, volume 1

NASA Technical Reports Server (NTRS)

1973-01-01

Geodetic information for NASA tracking stations and for observation stations cooperating in NASA geodetic satellite programs is presented. A Geodetic Data Sheet is provided for each station, giving the position of the station and describing briefly how it was established. Geodetic positions and geocentric coordinates of these stations are tabulated on local or major geodetic datums and on selected world geodetic systems. The principal tracking facilities used by NASA, including the Spaceflight Tracking and Data Network, the Deep Space Network, and several large radio telescopes are discussed. Positions of these facilities are tabulated on their local or national datums, the Mercury Spheroid 1960, the Modified Mercury Datum 1968, and the Spaceflight Tracking and Data Network System. Observation stations in the NASA Geodetic Satellites Program are included along with stations participating in the National Geodetic Satellite Program. Positions of these facilities are given on local or preferred major datums, and on the Modified Mercury Datum 1968.

Detail of old rain shed (Building No. 43) showing vertical ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail of old rain shed (Building No. 43) showing vertical posts on concrete footing with diagonal timber bracing and wire bracing. - Hawaii Volcanoes National Park Water Collection System, Hawaii Volcanoes National Park, Volcano, Hawaii County, HI

Detail of old rain shed (Building No. 43) showing vertical ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Detail of old rain shed (Building No. 43) showing vertical posts. Note rock foundations of wood tanks once located under the rain shed on the ground at center of photograph. - Hawaii Volcanoes National Park Water Collection System, Hawaii Volcanoes National Park, Volcano, Hawaii County, HI

NASA-Ames vertical gun

NASA Technical Reports Server (NTRS)

Schultz, P. H.

1984-01-01

A national facility, the NASA-Ames vertical gun range (AVGR) has an excellent reputation for revealing fundamental aspects of impact cratering that provide important constraints for planetary processes. The current logistics in accessing the AVGR, some of the past and ongoing experimental programs and their relevance, and the future role of this facility in planetary studies are reviewed. Publications resulting from experiments with the gun (1979 to 1984) are listed as well as the researchers and subjects studied.

Status of Water Levels and Selected Water-Quality Conditions in the Sparta-Memphis Aquifer in Arkansas and the Status of Water Levels in the Sparta Aquifer in Louisiana, Spring 2005

USGS Publications Warehouse

Schrader, T.P.; Jones, J.S.

2007-01-01

The U.S. Geological Survey in cooperation with the Arkansas Natural Resources Commission, the Arkansas Geological Commission, and the Louisiana Department of Transportation and Development has monitored water levels in the Sparta Sand of Claiborne Group and Memphis Sand of Claiborne Group since the 1920's. Ground-water withdrawals have increased while water levels have declined since monitoring was initiated. This report has been produced to describe ground-water levels in the aquifers in the Sparta Sand and Memphis Sand and provide information for the management of this valuable resource. The 2005 potentiometric-surface map of the aquifers in the Sparta Sand and Memphis Sand was constructed using water-level data collected in 333 wells in Arkansas and 120 wells in Louisiana during the spring of 2005. The highest water-level altitude measured in Arkansas was 327 feet above National Geodetic Vertical Datum of 1929 located in Grant County in the outcrop at the western boundary of the study area; the lowest water-level altitude was 189 feet below National Geodetic Vertical Datum of 1929 in Union County. The highest water-level altitude measured in Louisiana was 246 feet above National Geodetic Vertical Datum of 1929 located in Bossier Parish in the outcrop area near the western boundary of the study area; the lowest water-level altitude was 226 feet below National Geodetic Vertical Datum of 1929 in central Ouachita Parish. Three large depressions centered in Columbia, Jefferson, and Union Counties in Arkansas are the result of large withdrawals for industrial and public supplies. In Louisiana, three major pumping centers are in Ouachita, Jackson, and Lincoln Parishes. Water withdrawals from these major pumping centers primarily is used for industrial and public-supply purposes. Withdrawals from Ouachita and Lincoln Parishes and Union County, Arkansas, primarily for industrial purposes, have caused the resulting cones of depression to coalesce so that the -40 foot

The Effect of Pitch, Roll, and Yaw on Airborne Gravity Observations of the NOAA GRAV-D Project

NASA Astrophysics Data System (ADS)

Childers, V. A.; Kanney, J.; Youngman, M.

2017-12-01

Aircraft turbulence can wreak havoc on the gravity measurementby beam-style gravimeters. Prior studies have confirmed the correlation of poor quality airborne gravity data collection to amplified aircraft motion. Motion in the aircraft is the combined effect of the airframe design, the autopilot and its performance, and the weather/wind regime. NOAA's National Geodetic Survey has launched the Gravity for the Redefinition of the American Vertical Datum project (GRAV-D) to provide the foundation for a new national vertical datum by 2022. This project requires collecting airborne gravity data covering the entire country and its holdings. The motion of the aircraft employed in this project is of prime importance because we use a beam-style gravimeter mounted on a gyro-stabilized platform to align the sensor to a time-averaged local vertical. Aircraft turbulence will tend to drive the platform off-level, allowing horizontal forces to map into the vertical gravity measurement. Recently, the GRAV-D project has experimented with two new factors in airborne gravity data collection. The first aspect is the use of the Aurora optionally piloted Centaur aircraft. This aircraft can be flown either with or without a pilot, but the autopilot is specifically designed to be very accurate. Incorporated into the much smaller frame of this aircraft is a new gravimeter developed by Micro-g LaCoste, called the Turnkey Airborne Gravimeter System 7 (TAGS7). This smaller, lighter instrument also has a new design whereby the beam is held fixed in an electromagnetic force field. The result of this new configuration is notably improved data quality in wind conditions higher than can be tolerated by our current system. So, which caused the improvement, the aircraft motion or the new meter? This study will start to tease apart these two effects with recently collected survey data. Specifically, we will compare the motion profile of the Centaur aircraft with other aircraft in the GRAV-D portfolio

CIRSS vertical data integration, San Bernardino study

NASA Technical Reports Server (NTRS)

Hodson, W.; Christenson, J.; Michel, R. (Principal Investigator)

1982-01-01

The creation and use of a vertically integrated data base, including LANDSAT data, for local planning purposes in a portion of San Bernardino County, California are described. The project illustrates that a vertically integrated approach can benefit local users, can be used to identify and rectify discrepancies in various data sources, and that the LANDSAT component can be effectively used to identify change, perform initial capability/suitability modeling, update existing data, and refine existing data in a geographic information system. Local analyses were developed which produced data of value to planners in the San Bernardino County Planning Department and the San Bernardino National Forest staff.

The relationship between vertical jump power estimates and weightlifting ability: a field-test approach.

PubMed

Carlock, Jon M; Smith, Sarah L; Hartman, Michael J; Morris, Robert T; Ciroslan, Dragomir A; Pierce, Kyle C; Newton, Robert U; Harman, Everett A; Sands, William A; Stone, Michael H

2004-08-01

The purpose of this study was to assess the usefulness of the vertical jump and estimated vertical-jump power as a field test for weightlifting. Estimated PP output from the vertical jump was correlated with lifting ability among 64 USA national-level weightlifters (junior and senior men and women). Vertical jump was measured using the Kinematic Measurement System, consisting of a switch mat interfaced with a laptop computer. Vertical jumps were measured using a hands-on-hips method. A counter-movement vertical jump (CMJ) and a static vertical jump (SJ, 90 degrees knee angle) were measured. Two trials were given for each condition. Test-retest reliability for jump height was intra-class correlation (ICC) = 0.98 (CMJ) and ICC = 0.96 (SJ). Athletes warmed up on their own for 2-3 minutes, followed by 2 practice jumps at each condition. Peak power (PP) was estimated using the equations developed by Sayers et al. (24). The athletes' current lifting capabilities were assessed by a questionnaire, and USA national coaches checked the listed values. Differences between groups (i.e., men versus women, juniors versus resident lifters) were determined using t-tests (p < or = 0.05). Correlations were determined using Pearson's r. Results indicate that vertical jumping PP is strongly associated with weightlifting ability. Thus, these results indicate that PP derived from the vertical jump (CMJ or SJ) can be a valuable tool in assessing weightlifting performance.

Effect of the Earth's inner structure on the gravity in definitions of height systems

NASA Astrophysics Data System (ADS)

Tenzer, Robert; Foroughi, Ismael; Pitoňák, Martin; Šprlák, Michal

2017-04-01

In context of the vertical datum unification, the geoid-to-quasi-geoid separation has been of significant interest in recent years, because most of existing local vertical datums are realized in the system of either normal or orthometric heights. Nevertheless, the normal-orthometric heights are still used in many other countries where the normal gravity values along leveling lines were adopted instead of the observed gravity. Whereas the conversion between the orthometric and normal heights is defined by means of the mean gravity disturbances (i.e. differences between the mean values of the actual and normal gravity) along the plumbline within the topography, differences between the normal and normal-orthometric heights can be described by means of the surface gravity disturbances. Since the normal gravity field does not reflect the topographic masses and actual mass density distribution inside the Earth, the definition of gravity represents a principal aspect for a realization of particular vertical datum. To address this issue in this study, we investigate effects of the Earth's inner density structure on the surface and mean gravity disturbances, and discuss their impact on the vertical datum realization. These two gravity field quantities are computed globally with a spectral resolution complete to a spherical harmonic degree 2160 using the global gravity, terrain, ice-thickness, inland bathymetry and crustal structure models. Our results reveal that both, the surface and mean gravity disturbances mostly comprise the gravitational signal of topography and masses distributed below the geoid surface. Moreover, in polar areas, a significant contribution comes from large glaciers. In contrast, the contributions of anomalous density distribution within the topography attributed to major lakes, sediments and bedrock density variations are much less pronounced. We also demonstrate that the mean gravity disturbances within the topography are significantly modified

Increasing vertical resolution in US models to improve track forecasts of Hurricane Joaquin with HWRF as an example

PubMed Central

Zhang, Banglin; Tallapragada, Vijay; Weng, Fuzhong; Liu, Qingfu; Sippel, Jason A.; Ma, Zaizhong; Bender, Morris A.

2016-01-01

The atmosphere−ocean coupled Hurricane Weather Research and Forecast model (HWRF) developed at the National Centers for Environmental Prediction (NCEP) is used as an example to illustrate the impact of model vertical resolution on track forecasts of tropical cyclones. A number of HWRF forecasting experiments were carried out at different vertical resolutions for Hurricane Joaquin, which occurred from September 27 to October 8, 2015, in the Atlantic Basin. The results show that the track prediction for Hurricane Joaquin is much more accurate with higher vertical resolution. The positive impacts of higher vertical resolution on hurricane track forecasts suggest that National Oceanic and Atmospheric Administration/NCEP should upgrade both HWRF and the Global Forecast System to have more vertical levels. PMID:27698121

Vertical and horizontal control dilemmas in public hospitals.

PubMed

Pettersen, Inger Johanne; Solstad, Elsa

2015-01-01

The hospital sector in Norway has been continuously reorganized since 2002 and the reforms have created organizations that are functionally/vertically controlled, whereas the production lines are coordinated on a process or a lateral basis. The purpose of this paper is to focus on both the perceived functional vertical control and horizontal controls within and between the local hospitals and the regional administrative levels. A national survey study, complemented with interviews of some key informants and document studies. The study shows that the functional and vertical lines of management control are perceived to be operating according to the traditional views of management control. The study indicates that the horizontal tasks are not very well implemented, and we did not find interactive and lateral uses of management control systems for managerial purposes. New control problems arise when services are to be coordinated between autonomous units. The paper focuses on the control problems found within the horizontal, flat relationship between production units in hospitals; new organizational structures have emerged where lateral relations are important, but traditional control practices follow functional, vertical lines.

The Revolutionary Vertical Lift Technology (RVLT) Project

NASA Technical Reports Server (NTRS)

Yamauchi, Gloria K.

2018-01-01

The Revolutionary Vertical Lift Technology (RVLT) Project is one of six projects in the Advanced Air Vehicles Program (AAVP) of the NASA Aeronautics Research Mission Directorate. The overarching goal of the RVLT Project is to develop and validate tools, technologies, and concepts to overcome key barriers for vertical lift vehicles. The project vision is to enable the next generation of vertical lift vehicles with aggressive goals for efficiency, noise, and emissions, to expand current capabilities and develop new commercial markets. The RVLT Project invests in technologies that support conventional, non-conventional, and emerging vertical-lift aircraft in the very light to heavy vehicle classes. Research areas include acoustic, aeromechanics, drive systems, engines, icing, hybrid-electric systems, impact dynamics, experimental techniques, computational methods, and conceptual design. The project research is executed at NASA Ames, Glenn, and Langley Research Centers; the research extensively leverages partnerships with the US Army, the Federal Aviation Administration, industry, and academia. The primary facilities used by the project for testing of vertical-lift technologies include the 14- by 22-Ft Wind Tunnel, Icing Research Tunnel, National Full-Scale Aerodynamics Complex, 7- by 10-Ft Wind Tunnel, Rotor Test Cell, Landing and Impact Research facility, Compressor Test Facility, Drive System Test Facilities, Transonic Turbine Blade Cascade Facility, Vertical Motion Simulator, Mobile Acoustic Facility, Exterior Effects Synthesis and Simulation Lab, and the NASA Advanced Supercomputing Complex. To learn more about the RVLT Project, please stop by booth #1004 or visit their website at https://www.nasa.gov/aeroresearch/programs/aavp/rvlt.

Imaging a vertical shaft from a tunnel using muons

NASA Astrophysics Data System (ADS)

Bonal, N.; Preston, L. A.; Dorsey, D. J.; Schwellenbach, D.; Green, A.; Smalley, D.

2015-12-01

We use muon technology to image a vertical shaft from a tunnel. The density of the materials through which cosmic ray muons pass influences the flux of muons because muons are more attenuated by higher density material. Additionally, muons can travel several kilometers allowing measurements through deep rock. Density maps are generated from muon flux measurements to locate subsurface features like tunnel structures and ore bodies. Additionally, muon data can be jointly inverted with other data such as gravity and seismic to produce higher quality earth models than produced from a single method. We collected several weeks of data in a tunnel to image a vertical shaft. The minimum length of rock between the vertical shaft and the detector is 120 meters and the diameter of the vertical shaft is 4.6 meters. The rock the muons traveled through consists of Tertiary age volcanic tuff and steeply dipping, small-displacement faults. Results will be presented for muon flux in the tunnel and Monte-Carlo simulations of this experiment. Simulations from both GEANT4 (Geometry And Tracking version 4) and MCNP6 (Monte-Carlo N-Particle version 6) models will be compared. The tunnel overburden from muon measurements is also estimated and compared with actual the overburden. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

15 CFR Appendix A to Subpart L of... - Flower Garden Banks National Marine Sanctuary Boundary Coordinates

Code of Federal Regulations, 2010 CFR

2010-01-01

... set of boundary coordinates using the geographic positions of the North American Datum of 1983 (NAD 83). FGBNMS coordinates are now provided in both North American Datum of 1927 (NAD 27) and NAD 83. Point Latitude (N) Longitude (W) East Flower Garden Bank: (NAD 27) E-1 27 deg. 52′ 53.82718″ 93 deg. 37′ 41.30310...

Vertical interventions and system effects; have we learned anything from past experiences?

PubMed Central

Oliveira, Charlotte; Russo, Giuliano

2015-01-01

The recent Ebola Virus Outbreak had a devastating effect on West Africa's already feeble national health systems. We suggest that such an impact turned out to be catastrophic because it hit particularly hard human resources for health and the delivery of primary healthcare services, which are cross-sectional to any health system. National and international interventions failed to understand the nature of this interaction, and concentrated on attending urgent specific vertical functions to fight the outbreak - the pillars - such as surveillance, logistics, safe burials etc. Such patchwork and vertical intervention strategy was always going to fail to tackle a system-wide problem, particularly in already fragile systems. We suggest that future interventions will have to learn from the experience of past initiatives for the introduction of HIV-AIDS services, which started as vertical programs and ended up including ever growing health system strengthening components. PMID:26523197

Development of a seamless multisource topographic/bathymetric elevation model of Tampa Bay

USGS Publications Warehouse

Gesch, D.; Wilson, R.

2001-01-01

Many applications of geospatial data in coastal environments require knowledge of the nearshore topography and bathymetry. However, because existing topographic and bathymetric data have been collected independently for different purposes, it has been difficult to use them together at the land/water interface owing to differences in format, projection, resolution, accuracy, and datums. As a first step toward solving the problems of integrating diverse coastal datasets, the U.S. Geological Survey (USGS) and the National Oceanic and Atmospheric Administration (NOAA) are collaborating on a joint demonstration project to merge their data for the Tampa Bay region of Florida. The best available topographic and bathymetric data were extracted from the USGS National Elevation Dataset and the NOAA hydrographic survey database, respectively. Before being merged, the topographic and bathymetric datasets were processed with standard geographic information system tools to place them in a common horizontal reference frame. Also, a key part of the preprocessing was transformation to a common vertical reference through the use of VDatum, a new tool created by NOAA's National Geodetic Survey for vertical datum conversions. The final merged product is a seamless topographic/bathymetric model covering the Tampa Bay region at a grid spacing of 1 arc-second. Topographic LIDAR data were processed and merged with the bathymetry to demonstrate the incorporation of recent third party data sources for several test areas. A primary application of a merged topographic/bathymetric elevation model is for user-defined shoreline delineation, in which the user decides on the tidal condition (for example, low or high water) to be superimposed on the elevation data to determine the spatial position of the water line. Such a use of merged topographic/bathymetric data could lead to the development of a shoreline zone, which could reduce redundant mapping efforts by federal, state, and local agencies

Dynamic Heights in the Great Lakes at Different Epochs

NASA Astrophysics Data System (ADS)

Roman, D. R.

2016-12-01

Vertical control in the Great Lakes region is currently defined by the International Great Lakes Datum of 1985 (IGLD 85) in the form of dynamic heights. Starting in 2025, dynamic heights will be defined through GNSS-derived geometric coordinates and a geopotential model. This paper explores the behavior of an existing geopotential model at different epochs when the Great Lakes were at significantly different (meter-level) geopotential surfaces. Water surfaces were examined in 2015 and 2010 at six sites on Lakes Superior and Lake Erie (three on each Lake). These sites have collocated a Continuously Operating Reference Station (CORS) and a Water Level Sensor (WLS). The offset between the antenna phase center for the CORS and the WLS datum are known at each site. The WLS then measures the distance from its datum to the Lake surface via an open well. Thus it is possible to determine the height above an ellipsoid datum at these sites as long as both the CORS and WLS are operational. The geometric coordinates are then used to estimate the geopotential value from the xGEOID16B model. This accomplished in two steps. To provide an improved reference model, EGM2008 was spectrally enhanced using observations from the GOCE satellite gravity mission and aerogravity from the Gravity for the Redefinition of the American Vertical Datum (GRAV-D) Project. This enhanced model, xGEOID16B_Ref, is still only a five arcminute resolution model (d/o 2160), but resolves dynamic heights at about 2 cm on Lake Superior for December 2015. The reference model was primarily developed to determine a one arcminute geoid height grid, xGEOID16B, available on the NGS website. This geoid height model was used to iteratively develop improved geopotential value for each of the site locations, which then improved comparisons to the cm-level. Comparisons were then made at the 2010 epoch for these same locations to determine if the performance of the geopotential model was consistent.

76 FR 62329 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-07

...] Communities affected elevation * * Elevation in meters (MSL) Effective Modified Anne Arundel County, Maryland... + 8 + 10 Unincorporated Areas of Crain Highway. Anne Arundel County. Approximately 400 feet None + 105... American Vertical Datum. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. * * BFEs to be changed...

76 FR 9714 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-22

..., FEMA published in the Federal Register a proposed rule that included an erroneous Base Flood Elevation... as 355 feet, referenced to the North American Vertical Datum of 1988. DATES: Comments pertaining to... (FEMA) publishes proposed determinations of Base (1% annual-chance) Flood Elevations (BFEs) and modified...

NASA directory of observation station locations, volume 2

NASA Technical Reports Server (NTRS)

1971-01-01

The directory documents geodetic information for NASA tracking stations and observation stations in the NASA Geodetic Satellites Program, including stations participating in the National Geodetic Satellite Program. Station positions of these facilities are given on local or preferred major datums, and on the Modified Mercury Datum 1968. A geodetic data sheet is provided for each station, giving the position of the station and describing briefly how it was established. Geodetic positions and geocentric coordinates of these stations are tabulated on local or major geodetic datums, and on selected world geodetic systems when available information permits.

Geoid modeling in Mexico and the collaboration with Central America and the Caribbean.

NASA Astrophysics Data System (ADS)

Avalos, D.; Gomez, R.

2012-12-01

The model of geoidal heights for Mexico, named GGM10, is presented as a geodetic tool to support vertical positioning in the context of regional height system unification. It is a purely gravimetric solution computed by the Stokes-Helmert technique in resolution of 2.5 arc minutes. This product from the Instituto Nacional de Estadistica y Geografia (INEGI) is released together with a series of 10 gravimetric models which add to the improvements in description of the gravity field. In the recent years, the INEGI joined the initiative of the U.S. National Geodetic Survey and the Canada's Geodetic Survey Division to promote the regional height system unification. In an effort to further improve the compatibility among national geoid models in the region, the INEGI has begun to champion a network of specialists that includes national representatives from Central America and the Caribbean. Through the opening of opportunities for training and more direct access to international agreements and discussions, the tropical region is gaining participation. Now a significantly increased number of countries is pushing for a future North and Central American geoid-based vertical datum as support of height system unification.eoidal height in Mexico, mapped from the model GGM10.

Vertical Profiling of Air Pollution at RAPCD

NASA Technical Reports Server (NTRS)

Newchurch, Michael J.; Fuller, Kirk A.; Bowdle, David A.; Johnson, Steven; Knupp, Kevin; Gillani, Noor; Biazar, Arastoo; Mcnider, Richard T.; Burris, John

2004-01-01

The interaction between local and regional pollution levels occurs at the interface of the Planetary Boundary Layer and the Free Troposphere. Measuring the vertical distribution of ozone, aerosols, and winds with high temporal and vertical resolution is essential to diagnose the nature of this interchange and ultimately for accurately forecasting ozone and aerosol pollution levels. The Regional Atmospheric Profiling Center for Discovery, RAPCD, was built and instrumented to address this critical issue. The ozone W DIAL lidar, Nd:YAG aerosol lidar, and 2.1 micron Doppler wind lidar, along with balloon- borne ECC ozonesondes form the core of the W C D instrumentation for addressing this problem. Instrumentation in the associated Mobile Integrated Profiling (MIPS) laboratory includes 91 5Mhz profiler, sodar, and ceilometer. The collocated Applied particle Optics and Radiometry (ApOR) laboratory hosts an FTIR along with MOUDI and optical particle counters. With MODELS-3 analysis by colleagues in the National Space Science and Technology Center on the UAH campus and the co- located National Weather Service Forecasting Office in Huntsville, AL we are developing a unique facility for advancing the state of the science of pollution forecasting.

75 FR 31368 - Proposed Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-03

... referenced ground [caret] Communities affected elevation Elevation in meters (MSL) Effective Modified Santa.... Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ** BFEs to be... Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter...

77 FR 21476 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... Communities affected elevation above ground [caret] Elevation in meters (MSL) Modified Randolph County... Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter.... [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ADDRESSES City of Beebe Maps are available for...

76 FR 39011 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-05

... Communities affected elevation above ground [caret] Elevation in meters (MSL) Modified Rio Grande County... Unincorporated Areas of the Rio Grande, Rio Grande County. approximately 400 feet north of U.S. Route 160... Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter...

77 FR 41685 - Drawbridge Operation Regulation; Willamette River, Portland, OR

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-16

... deviation is necessary to accommodate Portland's Big Float event. This deviation allows the bridge to remain... of the Big Float event. The Hawthorne Bridge crosses the Willamette River at mile 13.1 and provides 49 feet of vertical clearance above Columbia River Datum 0.0 while in the closed position. Vessels...

THE VERTICAL

NASA Technical Reports Server (NTRS)

Albert, Stephen L.; Spencer, Jeffrey B.

1994-01-01

'THE VERTICAL' computer keyboard is designed to address critical factors which contribute to Repetitive Motion Injuries (RMI) (including Carpal Tunnel Syndrome) in association with computer keyboard usage. This keyboard splits the standard QWERTY design into two halves and positions each half 90 degrees from the desk. In order to access a computer correctly. 'THE VERTICAL' requires users to position their bodies in optimal alignment with the keyboard. The orthopaedically neutral forearm position (with hands palms-in and thumbs-up) reduces nerve compression in the forearm. The vertically arranged keypad halves ameliorate onset occurrence of keyboard-associated RMI. By utilizing visually-reference mirrored mylar surfaces adjustable to the user's eye, the user is able to readily reference any key indicia (reversed) just as they would on a conventional keyboard. Transverse adjustability substantially reduces cumulative musculoskeletal discomfort in the shoulders. 'THE VERTICAL' eliminates the need for an exterior mouse by offering a convenient finger-accessible curser control while the hands remain in the vertically neutral position. The potential commercial application for 'THE VERTICAL' is enormous since the product can effect every person who uses a computer anywhere in the world. Employers and their insurance carriers are spending hundreds of millions of dollars per year as a result of RMI. This keyboard will reduce the risk.

Water-level altitudes 2010 and water-level changes in the Chicot, Evangeline, and Jasper aquifers and compaction 1973-2009 in the Chicot and Evangeline aquifers, Houston-Galveston region, Texas

USGS Publications Warehouse

Kasmarek, Mark C.; Johnson, Michaela R.; Ramage, Jason K.

2010-01-01

Most of the subsidence in the Houston-Galveston region has occurred as a direct result of groundwater withdrawals for municipal supply, industrial use, and irrigation that depressured and dewatered the Chicot and Evangeline aquifers causing compaction of the clay layers of the aquifer sediments. This report, prepared by the U.S. Geological Survey, in cooperation with the Harris-Galveston Subsidence District, City of Houston, Fort Bend Subsidence District, and Lone Star Groundwater Conservation District, is one in an annual series of reports depicting water-level altitudes and water-level changes in the Chicot, Evangeline, and Jasper aquifers and compaction in the Chicot and Evangeline aquifers in the Houston-Galveston region. The report contains maps showing 2010 water-level altitudes for the Chicot, Evangeline, and Jasper aquifers, respectively; maps showing 1-year (2009-10) water-level-altitude changes for each aquifer; maps showing 5-year (2005-10) water-level-altitude changes for each aquifer; maps showing long-term (1990-2010 and 1977-2010) water-level-altitude changes for the Chicot and Evangeline aquifers; a map showing long-term (2000-10) water-level-altitude change for the Jasper aquifer; a map showing locations of borehole extensometer sites; and graphs showing measured compaction of subsurface material at the extensometers from 1973, or later, through 2009. Tables listing the data used to construct each aquifer-data map and the compaction graphs are included. Water levels in the Chicot, Evangeline, and Jasper aquifers were measured during December 2009-March 2010. In 2010, water-level-altitude contours for the Chicot aquifer ranged from 200 feet below National Geodetic Vertical Datum of 1929 or North American Vertical Datum of 1988 (hereinafter, datum) in a small area in southwestern Harris County to 200 feet above datum in central to southwestern Montgomery County. Water-level-altitude changes in the Chicot aquifer ranged from a 49-foot decline to a 67

Direct Observation of Ultralow Vertical Emittance using a Vertical Undulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wootton, Kent

2015-09-17

In recent work, the first quantitative measurements of electron beam vertical emittance using a vertical undulator were presented, with particular emphasis given to ultralow vertical emittances [K. P. Wootton, et al., Phys. Rev. ST Accel. Beams, 17, 112802 (2014)]. Using this apparatus, a geometric vertical emittance of 0.9 ± 0.3 pm rad has been observed. A critical analysis is given of measurement approaches that were attempted, with particular emphasis on systematic and statistical uncertainties. The method used is explained, compared to other techniques and the applicability of these results to other scenarios discussed.

Vertical integration - Reducing the load on GP teachers.

PubMed

Anderson, Katrina; Thomson, Jennifer

2009-11-01

With the increased medical student numbers in Australia there is an expectation that general practice will train students, junior doctors and registrars, and the teaching burden for busy general practitioners will rise. We discuss the model of vertical integration of general practice education set up at the Australian National University Medical School in the Australian Capital Territory and southeast New South Wales. This model of vertical integration is unique. It could be adapted in a range of vocational settings and spans medical student, prevocational doctor, registrar and international medical graduate teaching. A key aim of these strategies is to reduce the load on the clinical GP teacher as sustaining their contribution is crucial to the future of training in general practice.

Approximate direct georeferencing in national coordinates

NASA Astrophysics Data System (ADS)

Legat, Klaus

Direct georeferencing has gained an increasing importance in photogrammetry and remote sensing. Thereby, the parameters of exterior orientation (EO) of an image sensor are determined by GPS/INS, yielding results in a global geocentric reference frame. Photogrammetric products like digital terrain models or orthoimages, however, are often required in national geodetic datums and mapped by national map projections, i.e., in "national coordinates". As the fundamental mathematics of photogrammetry is based on Cartesian coordinates, the scene restitution is often performed in a Cartesian frame located at some central position of the image block. The subsequent transformation to national coordinates is a standard problem in geodesy and can be done in a rigorous manner-at least if the formulas of the map projection are rigorous. Drawbacks of this procedure include practical deficiencies related to the photogrammetric processing as well as the computational cost of transforming the whole scene. To avoid these problems, the paper pursues an alternative processing strategy where the EO parameters are transformed prior to the restitution. If only this transition was done, however, the scene would be systematically distorted. The reason is that the national coordinates are not Cartesian due to the earth curvature and the unavoidable length distortion of map projections. To settle these distortions, several corrections need to be applied. These are treated in detail for both passive and active imaging. Since all these corrections are approximations only, the resulting technique is termed "approximate direct georeferencing". Still, the residual distortions are usually very low as is demonstrated by simulations, rendering the technique an attractive approach to direct georeferencing.

77 FR 66555 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-11-06

.... [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ADDRESSES City of Chiefland Maps are available... American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1... feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. ADDRESSES City of...

77 FR 73324 - Final Flood Elevation Determinations

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-10

.... Depth in feet above ground. [caret] Mean Sea Level, rounded to the nearest 0.1 meter. [[Page 73326.... + North American Vertical Datum. Depth in feet above ground. [caret] Mean Sea Level, rounded to the... Sea Level, rounded to the nearest 0.1 meter. ADDRESSES City of Walnut Ridge Maps are available for...

78 FR 41389 - Free Flow Power Corporation; Notice of Application Ready for Environmental Analysis and...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-10

... of Natural Resources on the East Fork White River in Lawrence County, Indiana. No federal lands are... Williams dam is currently owned by the Indiana Department of Natural Resources and impounds a 553-acre reservoir at a normal pool elevation of 472.2 North American Vertical Datum of 1988 (NAVD 88). In addition...

77 FR 53141 - Drawbridge Operation Regulation; Columbia River, Vancouver, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-31

... lift-spans. This deviation allows height-restricted lifts which will reduce the vertical clearance... which cross the Columbia River at mile 106.5 only be required to lift to a reduced height of 130 feet above Columbia River Datum for a 30 day period. The height restricted lifts are necessary to facilitate...

Recent Darrieus vertical axis wind turbine aerodynamical experiments at Sandia National Laboratories

NASA Technical Reports Server (NTRS)

Klimas, P. C.

1981-01-01

Experiments contributing to the understanding of the aerodynamics of airfoils operating in the vertical axis wind turbine (VAWT) environment are described. These experiments are ultimately intended to reduce VAWT cost of energy and increase system reliability. They include chordwise pressure surveys, circumferential blade acceleration surveys, effects of blade camber, pitch and offset, blade blowing, and use of sections designed specifically for VAWT application.

Materials Examination of the Vertical Stabilizer from American Airlines Flight 587

NASA Technical Reports Server (NTRS)

Fox, Matthew R.; Schultheisz, Carl R.; Reeder, James R.; Jensen, Brian J.

2005-01-01

The first in-flight failure of a primary structural component made from composite material on a commercial airplane led to the crash of American Airlines Flight 587. As part of the National Transportation Safety Board investigation of the accident, the composite materials of the vertical stabilizer were tested, microstructure was analyzed, and fractured composite lugs that attached the vertical stabilizer to the aircraft tail were examined. In this paper the materials testing and analysis is presented, composite fractures are described, and the resulting clues to the failure events are discussed.

14 CFR Appendix F to Part 91 - Helicopter Flight Recorder Specifications

Code of Federal Regulations, 2011 CFR

2011-01-01

...-a) 1 25 to 150 ft. Magnetic Heading 360° ±5° 1 1° Vertical Acceleration −3g to +6g ±0.2g in addition to ±0.3g maximum datum 4 (or 1 per second where peaks, ref. to 1g are recorded) 0.05g. Longitudinal...

Estimation of hepatitis C virus infections resulting from vertical transmission in Egypt.

PubMed

Benova, Lenka; Awad, Susanne F; Miller, F DeWolfe; Abu-Raddad, Laith J

2015-03-01

Despite having the highest hepatitis C virus (HCV) prevalence in the world, the ongoing level of HCV incidence in Egypt and its drivers are poorly understood. Whereas HCV mother-to-child infection is a well-established transmission route, there are no estimates of HCV infections resulting from vertical transmission for any country, including Egypt. The aim of this study was to estimate the absolute number of new HCV infections resulting from vertical transmission in Egypt. We developed a conceptual framework of HCV vertical transmission, expressed in terms of a mathematical model and based on maternal HCV antibody and viremia. The mathematical model estimated the number of HCV vertical infections nationally and for six subnational areas. Applying two vertical transmission risk estimates to the 2008 Egyptian birth cohort, we estimated that between 3,080 and 5,167 HCV infections resulted from vertical transmission among children born in 2008. HCV vertical transmission may account for half of incident cases in the <5-year age group. Disproportionately higher proportions of vertical infections were estimated in Lower Rural and Upper Rural subnational areas. This geographical clustering was a result of higher-area-level HCV prevalence among women and higher fertility rates. Vertical transmission is one of the primary HCV infection routes among children<5 years in Egypt. The absolute number of vertical transmissions and the young age at infection highlight a public health concern. These findings also emphasize the need to quantify the relative contributions of other transmission routes to HCV incidence in Egypt. © 2014 The Authors. Hepatology published by Wiley Periodicals, Inc., on behalf of the American Association for the Study of Liver Diseases.

47 CFR 76.504 - Limits on carriage of vertically integrated programming.

Code of Federal Regulations, 2014 CFR

2014-10-01

... programming. 76.504 Section 76.504 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Limits on carriage of vertically integrated programming. (a) Except as otherwise provided in this section... national video programming services owned by the cable operator or in which the cable operator has an...

47 CFR 76.504 - Limits on carriage of vertically integrated programming.

Code of Federal Regulations, 2010 CFR

2010-10-01

... programming. 76.504 Section 76.504 Telecommunication FEDERAL COMMUNICATIONS COMMISSION (CONTINUED) BROADCAST... Limits on carriage of vertically integrated programming. (a) Except as otherwise provided in this section... national video programming services owned by the cable operator or in which the cable operator has an...

14 CFR Appendix C to Part 135 - Helicopter Flight Recorder Specifications

Code of Federal Regulations, 2011 CFR

2011-01-01

.... (see Table 1, TSO C51-a) 1 25 to 150 ft. Magnetic heading 360° ±5° 1 1°. Vertical acceleration −3g to +6g ±0.2g in addition to ±0.3g maximum datum 4 (or 1 per second where peaks, ref. to 1g are recorded...

Advances and Best Practices in Airborne Gravimetry from the U.S. GRAV-D Project

NASA Astrophysics Data System (ADS)

Diehl, Theresa; Childers, Vicki; Preaux, Sandra; Holmes, Simon; Weil, Carly

2013-04-01

The Gravity for the Redefinition of the American Vertical Datum (GRAV-D) project, an official policy of the U.S. National Geodetic Survey as of 2007, is working to survey the entire U.S. and its holdings with high-altitude airborne gravimetry. The goal of the project is to provide a consistent, high-quality gravity dataset that will become the cornerstone of a new gravimetric geoid and national vertical datum in 2022. Over the last five years, the GRAV-D project has surveyed more than 25% of the country, accomplishing almost 500 flights on six different aircraft platforms and producing more than 3.7 Million square km of data thus far. This wealth of experience has led to advances in the collection, processing, and evaluation of high-altitude (20,000 - 35,000 ft) airborne gravity data. This presentation will highlight the most important practical and theoretical advances of the GRAV-D project, giving an introduction to each. Examples of innovation include: 1. Use of navigation grade inertial measurement unit data and precise lever arm measurements for positioning; 2. New quality control tests and software for near real-time analysis of data in the field; 3. Increased accuracy of gravity post-processing by reexamining assumptions and simplifications that were inconsistent with a goal of 1 mGal precision; and 4. Better final data evaluation through crossovers, additional statistics, and inclusion of airborne data into harmonic models that use EGM08 as a base model. The increases in data quality that resulted from implementation of the above advances (and others) will be shown with a case study of the GRAV-D 2008 southern Alaska survey near Anchorage, over Cook Inlet. The case study's statistics and comparisons to global models illustrate the impact that these advances have had on the final airborne gravity data quality. Finally, the presentation will summarize the best practices identified by the project from its last five years of experience.

Vertical axis wind turbines

DOEpatents

Krivcov, Vladimir [Miass, RU; Krivospitski, Vladimir [Miass, RU; Maksimov, Vasili [Miass, RU; Halstead, Richard [Rohnert Park, CA; Grahov, Jurij [Miass, RU

2011-03-08

A vertical axis wind turbine is described. The wind turbine can include a top ring, a middle ring and a lower ring, wherein a plurality of vertical airfoils are disposed between the rings. For example, three vertical airfoils can be attached between the upper ring and the middle ring. In addition, three more vertical airfoils can be attached between the lower ring and the middle ring. When wind contacts the vertically arranged airfoils the rings begin to spin. By connecting the rings to a center pole which spins an alternator, electricity can be generated from wind.

[Results of the implementation of three national guidelines for the prevention of HIV vertical transmission in Instituto Nacional Materno Perinatal. Lima, Peru].

PubMed

Velásquez, Carlos

2011-01-01

A retrospective analysis is performed in three successive periods between the years 1996 and 2009, in order to evaluate the impact of the implementation of three national guidelines for the prevention of the vertical transmission of HIV. 275 births were included in 13 years. Significant statistical differences were found in the percentage of HIV cases in the children exposed to the virus between the three periods: 15% during the period in which only zidovudine (AZT) was administered to the pregnant woman, 6.4% during the second period (administration of AZT to the pregnant woman not fulfilling HAART initiation criteria and HAART to those fulfilling criteria for this treatment), and 4% during the third period in which HAART was applied to all pregnant women with HIV infection. 95% of pregnant women ended their pregnancy by cesarean section and the 100% of children received infant formula. Changes made in national guidelines have produced a positive impact in the decrease of HIV infected children in the Instituto Nacional Materno Perinatal in Peru.

Going beyond the vertical: leveraging a national HIV quality improvement programme to address other health priorities in Haiti.

PubMed

Joseph, Jean Paul; Jerome, Gregory; Lambert, Wesler; Almazor, Patrick; Cupidon, Colette Eugene; Hirschhorn, Lisa R

2015-07-01

Although the central role of quality to achieve targeted population health goals is widely recognized, how to spread the capacity to measure and improve quality across programmes has not been widely studied. We describe the successful leveraging of expertise and framework of a national HIV quality improvement programme to spread capacity and improve quality across a network of clinics in HIV and other targeted areas of healthcare delivery in rural Haiti.The work was led by Zamni LaSante, a Haitian nongovernment organization and its sister organization, Partners In Health working in partnership with the Haitian Ministry of Health in the Plateau Central and Lower Artibonite regions in 12 public sector facilities.Data included routinely collected organizational assessments of facility quality improvement capacity, national HIV performance measures and Zamni LaSante programme records.We found that facility quality improvement capacity increased with spread from HIV to other areas of inpatient and outpatient care, including tuberculosis (TB), maternal health and inpatient services in all 12 supported healthcare facilities. A significant increase in the quality of HIV care was also seen in most areas, including CD4 monitoring, TB screening, HIV treatment (all P < 0.01) and nutritional assessment and prevention of mother-to-child transmission (both P < .05), with an increase in average facility performance from 39 to 72% (P < .01).In conclusion, using a diagonal approach to leverage a national vertical programme for wider benefit resulted in accelerated change in professional culture and increased capacity to spread quality improvement activities across facilities and areas of healthcare delivery. This led to improvement within and beyond HIV care and contributed to the goal of quality of care for all.

4. VIEW OF VERTICAL BORING MACHINE. (Bullard) Vertical turning lathe ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. VIEW OF VERTICAL BORING MACHINE. (Bullard) Vertical turning lathe (VTL). Machining the fixture for GE Turboshroud. G.S. O'Brien, operator. - Juniata Shops, Machine Shop No. 1, East of Fourth Avenue at Third Street, Altoona, Blair County, PA

Signatures of Currency Vertices

NASA Astrophysics Data System (ADS)

Holme, Petter

2009-03-01

Many real-world networks have broad degree distributions. For some systems, this means that the functional significance of the vertices is also broadly distributed, in other cases the vertices are equally significant, but in different ways. One example of the latter case is metabolic networks, where the high-degree vertices — the currency metabolites — supply the molecular groups to the low-degree metabolites, and the latter are responsible for the higher-order biological function, of vital importance to the organism. In this paper, we propose a generalization of currency metabolites to currency vertices. We investigate the network structural characteristics of such systems, both in model networks and in some empirical systems. In addition to metabolic networks, we find that a network of music collaborations and a network of e-mail exchange could be described by a division of the vertices into currency vertices and others.

Estimation of shoreline position and change using airborne topographic lidar data

USGS Publications Warehouse

Stockdon, H.F.; Sallenger, A.H.; List, J.H.; Holman, R.A.

2002-01-01

A method has been developed for estimating shoreline position from airborne scanning laser data. This technique allows rapid estimation of objective, GPS-based shoreline positions over hundreds of kilometers of coast, essential for the assessment of large-scale coastal behavior. Shoreline position, defined as the cross-shore position of a vertical shoreline datum, is found by fitting a function to cross-shore profiles of laser altimetry data located in a vertical range around the datum and then evaluating the function at the specified datum. Error bars on horizontal position are directly calculated as the 95% confidence interval on the mean value based on the Student's t distribution of the errors of the regression. The technique was tested using lidar data collected with NASA's Airborne Topographic Mapper (ATM) in September 1997 on the Outer Banks of North Carolina. Estimated lidar-based shoreline position was compared to shoreline position as measured by a ground-based GPS vehicle survey system. The two methods agreed closely with a root mean square difference of 2.9 m. The mean 95% confidence interval for shoreline position was ?? 1.4 m. The technique has been applied to a study of shoreline change on Assateague Island, Maryland/Virginia, where three ATM data sets were used to assess the statistics of large-scale shoreline change caused by a major 'northeaster' winter storm. The accuracy of both the lidar system and the technique described provides measures of shoreline position and change that are ideal for studying storm-scale variability over large spatial scales.

Topobathymetric elevation model development using a new methodology: Coastal National Elevation Database

USGS Publications Warehouse

Danielson, Jeffrey J.; Poppenga, Sandra K.; Brock, John C.; Evans, Gayla A.; Tyler, Dean; Gesch, Dean B.; Thatcher, Cindy A.; Barras, John

2016-01-01

During the coming decades, coastlines will respond to widely predicted sea-level rise, storm surge, and coastalinundation flooding from disastrous events. Because physical processes in coastal environments are controlled by the geomorphology of over-the-land topography and underwater bathymetry, many applications of geospatial data in coastal environments require detailed knowledge of the near-shore topography and bathymetry. In this paper, an updated methodology used by the U.S. Geological Survey Coastal National Elevation Database (CoNED) Applications Project is presented for developing coastal topobathymetric elevation models (TBDEMs) from multiple topographic data sources with adjacent intertidal topobathymetric and offshore bathymetric sources to generate seamlessly integrated TBDEMs. This repeatable, updatable, and logically consistent methodology assimilates topographic data (land elevation) and bathymetry (water depth) into a seamless coastal elevation model. Within the overarching framework, vertical datum transformations are standardized in a workflow that interweaves spatially consistent interpolation (gridding) techniques with a land/water boundary mask delineation approach. Output gridded raster TBDEMs are stacked into a file storage system of mosaic datasets within an Esri ArcGIS geodatabase for efficient updating while maintaining current and updated spatially referenced metadata. Topobathymetric data provide a required seamless elevation product for several science application studies, such as shoreline delineation, coastal inundation mapping, sediment-transport, sea-level rise, storm surge models, and tsunami impact assessment. These detailed coastal elevation data are critical to depict regions prone to climate change impacts and are essential to planners and managers responsible for mitigating the associated risks and costs to both human communities and ecosystems. The CoNED methodology approach has been used to construct integrated TBDEM models

An analysis of methods for gravity determination and their utilization for the calculation of geopotential numbers in the Slovak national levelling network

NASA Astrophysics Data System (ADS)

Majkráková, Miroslava; Papčo, Juraj; Zahorec, Pavol; Droščák, Branislav; Mikuška, Ján; Marušiak, Ivan

2016-09-01

The vertical reference system in the Slovak Republic is realized by the National Levelling Network (NLN). The normal heights according to Molodensky have been introduced as reference heights in the NLN in 1957. Since then, the gravity correction, which is necessary to determine the reference heights in the NLN, has been obtained by an interpolation either from the simple or complete Bouguer anomalies. We refer to this method as the "original". Currently, the method based on geopotential numbers is the preferred way to unify the European levelling networks. The core of this article is an analysis of different ways to the gravity determination and their application for the calculation of geopotential numbers at the points of the NLN. The first method is based on the calculation of gravity at levelling points from the interpolated values of the complete Bouguer anomaly using the CBA2G_SK software. The second method is based on the global geopotential model EGM2008 improved by the Residual Terrain Model (RTM) approach. The calculated gravity is used to determine the normal heights according to Molodensky along parts of the levelling lines around the EVRF2007 datum point EH-V. Pitelová (UELN-1905325) and the levelling line of the 2nd order NLN to Kráľova hoľa Mountain (the highest point measured by levelling). The results from our analysis illustrate that the method based on the interpolated value of gravity is a better method for gravity determination when we do not know the measured gravity. It was shown that this method is suitable for the determination of geopotential numbers and reference heights in the Slovak national levelling network at the points in which the gravity is not observed directly. We also demonstrated the necessity of using the precise RTM for the refinement of the results derived solely from the EGM2008.

Observations of copolar correlation coefficient through a bright band at vertical incidence

NASA Technical Reports Server (NTRS)

Zrnic, D. S.; Raghavan, R.; Chandrasekar, V.

1994-01-01

This paper discusses an application of polarimetric measurements at vertical incidence. In particular, the correlation coefficients between linear copolar components are examined, and measurements obtained with the National Severe Storms Laboratory (NSSL)'s and National Center for Atmospheric Research (NCAR)'s polarimetric radars are presented. The data are from two well-defined bright bands. A sharp decrease of the correlation coefficient, confined to a height interval of a few hundred meters, marks the bottom of the bright band.

A guidance and control assessment of three vertical landing options for RLV

NASA Technical Reports Server (NTRS)

Gallaher, M.; Coughlin, D.; Krupp, D

1995-01-01

The National Aeronautics and Space Administration is considering a vertical lander as a candidate concept for a single-stage-to-orbit reusable launch vehicle (RLV). Three strategies for guiding and controlling the inversion of a reentering RLV from a nose-first attitude to a vertical landing attitude are suggested. Each option is simulated from a common reentry state to touchdown, using a common guidance algorithm and different controllers. Results demonstrate the characteristics that typify and distinguish each concept and help to identify peculiar problems, level of guidance and control sophistication required, feasibility concerns, and areas in which stringent subsystem requirements will be imposed by guidance and control.

Dependence of Hurricane intensity and structures on vertical resolution and time-step size

NASA Astrophysics Data System (ADS)

Zhang, Da-Lin; Wang, Xiaoxue

2003-09-01

In view of the growing interests in the explicit modeling of clouds and precipitation, the effects of varying vertical resolution and time-step sizes on the 72-h explicit simulation of Hurricane Andrew (1992) are studied using the Pennsylvania State University/National Center for Atmospheric Research (PSU/NCAR) mesoscale model (i.e., MM5) with the finest grid size of 6 km. It is shown that changing vertical resolution and time-step size has significant effects on hurricane intensity and inner-core cloud/precipitation, but little impact on the hurricane track. In general, increasing vertical resolution tends to produce a deeper storm with lower central pressure and stronger three-dimensional winds, and more precipitation. Similar effects, but to a less extent, occur when the time-step size is reduced. It is found that increasing the low-level vertical resolution is more efficient in intensifying a hurricane, whereas changing the upper-level vertical resolution has little impact on the hurricane intensity. Moreover, the use of a thicker surface layer tends to produce higher maximum surface winds. It is concluded that the use of higher vertical resolution, a thin surface layer, and smaller time-step sizes, along with higher horizontal resolution, is desirable to model more realistically the intensity and inner-core structures and evolution of tropical storms as well as the other convectively driven weather systems.

The quest for the perfect gravity anomaly: Part 1 - New calculation standards

USGS Publications Warehouse

Li, X.; Hildenbrand, T.G.; Hinze, W. J.; Keller, Gordon R.; Ravat, D.; Webring, M.

2006-01-01

The North American gravity database together with databases from Canada, Mexico, and the United States are being revised to improve their coverage, versatility, and accuracy. An important part of this effort is revision of procedures and standards for calculating gravity anomalies taking into account our enhanced computational power, modern satellite-based positioning technology, improved terrain databases, and increased interest in more accurately defining different anomaly components. The most striking revision is the use of one single internationally accepted reference ellipsoid for the horizontal and vertical datums of gravity stations as well as for the computation of the theoretical gravity. The new standards hardly impact the interpretation of local anomalies, but do improve regional anomalies. Most importantly, such new standards can be consistently applied to gravity database compilations of nations, continents, and even the entire world. ?? 2005 Society of Exploration Geophysicists.

Potentiometric surface of the Floridan Aquifer, St. Johns River Water Management District and vicinity, Florida, May 1981

USGS Publications Warehouse

Schiner, George R.; Hayes, Eugene C.

1981-01-01

This map presents the potentiometric surface of the Floridan aquifer in the St. Johns River Water Management District and vicinity for May 1981. The Floridan aquifer is the principal source of potable water in the area. Water-level measurements were made in approximately 1,000 wells and at several springs. The potentiometric surface is shown mostly by 5-foot contour intervals. In the Fernandina Beach area 20 and 40-foot intervals are used to show a deep cone of depression. The potentiometric surface ranged from 122 feet above NGVD (National Geodetic Vertical Datum of 1929) in Polk County to 125 feet below NGVD in Nassau County. Water levels were at record lows in many counties due to lack of rainfall. Declines were as much as 10 feet and commonly 5 feet from the May 1980 levels. (USGS)

Latitude and longitude vertical disparity

PubMed Central

Read, Jenny C. A.; Phillipson, Graeme P.; Glennerster, Andrew

2010-01-01

The literature on vertical disparity is complicated by the fact that several different definitions of the term “vertical disparity” are in common use, often without a clear statement about which is intended or a widespread appreciation of the properties of the different definitions. Here, we examine two definitions of retinal vertical disparity: elevation-latitude and elevation-longitude disparity. Near the fixation point, these definitions become equivalent, but in general, they have quite different dependences on object distance and binocular eye posture, which have not previously been spelt out. We present analytical approximations for each type of vertical disparity, valid for more general conditions than previous derivations in the literature: we do not restrict ourselves to objects near the fixation point or near the plane of regard, and we allow for non-zero torsion, cyclovergence and vertical misalignments of the eyes. We use these expressions to derive estimates of the latitude and longitude vertical disparity expected at each point in the visual field, averaged over all natural viewing. Finally, we present analytical expressions showing how binocular eye position – gaze direction, convergence, torsion, cyclovergence, and vertical misalignment – can be derived from the vertical disparity field and its derivatives at the fovea. PMID:20055544

Cambrian Evolutionary Radiation: Context, correlation, and chronostratigraphy—Overcoming deficiencies of the first appearance datum (FAD) concept

NASA Astrophysics Data System (ADS)

Landing, Ed; Geyer, Gerd; Brasier, Martin D.; Bowring, Samuel A.

2013-08-01

Use of the first appearance datum (FAD) of a fossil to define a global chronostratigraphic unit's base can lead to intractable correlation and stability problems. FADs are diachronous—they reflect species' evolutionary history, dispersal, biofacies, preservation, collection, and taxonomy. The Cambrian Evolutionary Radiation is characterised by diachronous FADs, biofacies controls, and provincialism of taxa and ecological communities that confound a stable Lower Cambrian chronostratigraphy. Cambrian series and stage definitions require greater attention to assemblage zone successions and non-biostratigraphic, particularly carbon isotope, correlation techniques such as those that define the Ediacaran System base. A redefined, basal Cambrian Trichophycus pedum Assemblage Zone lies above the highest Ediacaran-type biotas (vendobionts, putative metazoans, and calcareous problematica such as Cloudina) and the basal Asteridium tornatum-Comasphaeridium velvetum Zone (acritarchs). This definition and the likely close correspondence of evolutionary origin and local FAD of T. pedum preserves the Fortune Head, Newfoundland, GSSP of the Cambrian base and allows the presence of sub-Cambrian, branched ichnofossils. The sub-Tommotian-equivalent base of Stage 2 (a suggested "Laolinian Stage") should be defined by the I'/L4/ZHUCE δ13C positive peak, bracketed by the lower ranges of Watsonella crosbyi and Aldanella attleborensis (molluscs) and the Skiagia ornata-Fimbrioglomerella membranacea Zone (acritarchs). The W. crosbyi and A. attleborensis FADs cannot define a Stage 2 base as they are diachronous even in the Newfoundland "type" W. crosbyi Zone. The Series 2 base cannot be based on a species' FAD owing to the provincialism of skeletalised metazoans in the Terreneuvian-Series 2 boundary interval and global heterochrony of the oldest trilobites. A Series 2 and Stage 3 (a suggested "Lenaldanian Series" and "Zhurinskyan Stage," new) GSSP base is proposed at the Siberian lower

Ecological Origins of Freedom: Pathogens, Heat Stress, and Frontier Topography Predict More Vertical but Less Horizontal Governmental Restriction.

PubMed

Conway, Lucian Gideon; Bongard, Kate; Plaut, Victoria; Gornick, Laura Janelle; Dodds, Daniel P; Giresi, Thomas; Tweed, Roger G; Repke, Meredith A; Houck, Shannon C

2017-10-01

What kinds of physical environments make for free societies? The present research investigates the effect of three different types of ecological stressors (climate stress, pathogen stress, and frontier topography) on two measurements of governmental restriction: Vertical restriction involves select persons imposing asymmetrical laws on others, while horizontal restriction involves laws that restrict most members of a society equally. Investigation 1 validates our measurements of vertical and horizontal restriction. Investigation 2 demonstrates that, across both U.S. states and a sample of nations, ecological stressors tend to cause more vertically restrictive societies but less horizontally restrictive societies. Investigation 3 demonstrates that assortative sociality partially mediates ecological stress→restriction relationships across nations, but not in U.S. states. Although some stressor-specific effects emerged (most notably, cold stress consistently showed effects in the opposite direction), these results in the main suggest that ecological stress simultaneously creates opposing pressures that push freedom in two different directions.

Biodiesel and Integrated STEM: Vertical Alignment of High School Biology/Biochemistry and Chemistry

ERIC Educational Resources Information Center

Burrows, Andrea C.; Breiner, Jonathan M.; Keiner, Jennifer; Behm, Chris

2014-01-01

This article explores the vertical alignment of two high school classes, biology and chemistry, around the core concept of biodiesel fuel production. High school teachers and university faculty members investigated biodiesel as it relates to societal impact through a National Science Foundation Research Experience for Teachers. Using an action…

Retrieving Vertical Air Motion and Raindrop Size Distributions from Vertically Pointing Doppler Radars

NASA Astrophysics Data System (ADS)

Williams, C. R.; Chandra, C. V.

2017-12-01

The vertical evolution of falling raindrops is a result of evaporation, breakup, and coalescence acting upon those raindrops. Computing these processes using vertically pointing radar observations is a two-step process. First, the raindrop size distribution (DSD) and vertical air motion need to be estimated throughout the rain shaft. Then, the changes in DSD properties need to be quantified as a function of height. The change in liquid water content is a measure of evaporation, and the change in raindrop number concentration and size are indicators of net breakup or coalescence in the vertical column. The DSD and air motion can be retrieved using observations from two vertically pointing radars operating side-by-side and at two different wavelengths. While both radars are observing the same raindrop distribution, they measure different reflectivity and radial velocities due to Rayleigh and Mie scattering properties. As long as raindrops with diameters greater than approximately 2 mm are in the radar pulse volumes, the Rayleigh and Mie scattering signatures are unique enough to estimate DSD parameters using radars operating at 3- and 35-GHz (Williams et al. 2016). Vertical decomposition diagrams (Williams 2016) are used to explore the processes acting on the raindrops. Specifically, changes in liquid water content with height quantify evaporation or accretion. When the raindrops are not evaporating, net raindrop breakup and coalescence are identified by changes in the total number of raindrops and changes in the DSD effective shape as the raindrops. This presentation will focus on describing the DSD and air motion retrieval method using vertical profiling radar observations from the Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) central facility in Northern Oklahoma.

Performance Enhancement of a Full-Scale Vertical Tail Model Equipped with Active Flow Control

NASA Technical Reports Server (NTRS)

Whalen, Edward A.; Lacy, Douglas; Lin, John C.; Andino, Marlyn Y.; Washburn, Anthony E.; Graff, Emilio; Wygnanski, Israel J.

2015-01-01

This paper describes wind tunnel test results from a joint NASA/Boeing research effort to advance active flow control (AFC) technology to enhance aerodynamic efficiency. A full-scale Boeing 757 vertical tail model equipped with sweeping jet actuators was tested at the National Full-Scale Aerodynamics Complex (NFAC) 40- by 80-Foot Wind Tunnel (40x80) at NASA Ames Research Center. The model was tested at a nominal airspeed of 100 knots and across rudder deflections and sideslip angles that covered the vertical tail flight envelope. A successful demonstration of AFC-enhanced vertical tail technology was achieved. A 31- actuator configuration significantly increased side force (by greater than 20%) at a maximum rudder deflection of 30deg. The successful demonstration of this application has cleared the way for a flight demonstration on the Boeing 757 ecoDemonstrator in 2015.

Coastal Digital Elevation Models (DEMs) for tsunami hazard assessment on the French coasts

NASA Astrophysics Data System (ADS)

Maspataud, Aurélie; Biscara, Laurie; Hébert, Hélène; Schmitt, Thierry; Créach, Ronan

2015-04-01

Building precise and up-to-date coastal DEMs is a prerequisite for accurate modeling and forecasting of hydrodynamic processes at local scale. Marine flooding, originating from tsunamis, storm surges or waves, is one of them. Some high resolution DEMs are being generated for multiple coast configurations (gulf, embayment, strait, estuary, harbor approaches, low-lying areas…) along French Atlantic and Channel coasts. This work is undertaken within the framework of the TANDEM project (Tsunamis in the Atlantic and the English ChaNnel: Definition of the Effects through numerical Modeling) (2014-2017). DEMs boundaries were defined considering the vicinity of French civil nuclear facilities, site effects considerations and potential tsunamigenic sources. Those were identified from available historical observations. Seamless integrated topographic and bathymetric coastal DEMs will be used by institutions taking part in the study to simulate expected wave height at regional and local scale on the French coasts, for a set of defined scenarii. The main tasks were (1) the development of a new capacity of production of DEM, (2) aiming at the release of high resolution and precision digital field models referred to vertical reference frameworks, that require (3) horizontal and vertical datum conversions (all source elevation data need to be transformed to a common datum), on the basis of (4) the building of (national and/or local) conversion grids of datum relationships based on known measurements. Challenges in coastal DEMs development deal with good practices throughout model development that can help minimizing uncertainties. This is particularly true as scattered elevation data with variable density, from multiple sources (national hydrographic services, state and local government agencies, research organizations and private engineering companies) and from many different types (paper fieldsheets to be digitized, single beam echo sounder, multibeam sonar, airborne laser

Recent advances in preparation, properties and device applications of two-dimensional h-BN and its vertical heterostructures

NASA Astrophysics Data System (ADS)

Yang, Huihui; Gao, Feng; Dai, Mingjin; Jia, Dechang; Zhou, Yu; Hu, Pingan

2017-03-01

Two-dimensional (2D) layered materials, such as graphene, hexagonal boron nitride (h-BN), molybdenum disulfide (MoS{}2 ), have attracted tremendous interest due to their atom-thickness structures and excellent physical properties. h-BN has predominant advantages as the dielectric substrate in FET devices due to its outstanding properties such as chemically inert surface, being free of dangling bonds and surface charge traps, especially the large-band-gap insulativity. h-BN involved vertical heterostructures have been widely exploited during the past few years. Such heterostructures adopting h-BN as dielectric layers exhibit enhanced electronic performance, and provide further possibilities for device engineering. Besides, a series of intriguing physical phenomena are observed in certain vertical heterostructures, such as superlattice potential induced replication of Dirac points, band gap tuning, Hofstadter butterfly states, gate-dependent pseudospin mixing. Herein we focus on the rapid developments of h-BN synthesis and fabrication of vertical heterostructures devices based on h-BN, and review the novel properties as well as the potential applications of the heterostructures composed of h-BN. Project supported by the National Natural Science Foundation of China (Nos. 61390502, 21373068), the National Basic Research Program of China (No. 2013CB632900), the Foundation for Innovative Research Groups of the National Natural Science Foundation of China (No. 51521003), and the Self-Planned Task of State Key Laboratory of Robotics and System (No. SKLRS201607B).

GOCE-based height system unification between Greece and Turkey. First considerations over marine and land areas

NASA Astrophysics Data System (ADS)

Vergos, Georgios S.; Erol, Bihter; Natsiopoulos, Dimitrios A.; Grigoriadis, Vassilios N.; Serkan Işık, Mustafa; Tziavos, Ilias N.

2016-04-01

The unification of local vertical Datums (LVDs) at a country-wide scale has gained significant attention lately, due to the availability of GOCE-based Global Geopotential Models (GGMs). The latter, offer unprecedented geoid height accuracies at the 1-1.5 cm level for spherical harmonic expansions to d/o 225-230. Within a single country, several LVDs may be used, especially in the event of islandic nations, therefore the unification of all of them to a single nation-wide LVD is of utmost importance. The same holds for neighboring countries, where the unification of their vertical datums is necessary as a tool of engineering, cross-border collaboration and environmental and risk management projects. The aforementioned set the main scope of the work carried out in the frame of the present study, which referred to the use of GOCE and GOCE/GRACE GGMs in order to unify the LVDs of Greece and Turkey. It is well-known that the two countries share common borders and are a path for large-scale engineering projects in the energy sector. Therefore, the availability of a common reference for orthometric heights in both countries and/or the determination of the relative offset of their individual zero-level geopotential value poses an emerging issue. The determination of the geopotential value Wo(LVD) for the Greek and Turkish LVDs was first carried out separately for each region performing as well different estimates for the marine area of the Aegean Sea and the terrestrial border-region along eastern Thrace. From that, possible biases of the Hellenic and Turkish LVDs themselves have been drawn and analyzed to determine spatial correlations. Then, the relative offset between the two LVDs was determined employing GPS/Levelling data for both areas and the latest GO-DIR-R5, GO-TIM-R5 and GOCO05s models as well as EGM2008. The estimation of the mean offset was used to provide as well a direct link between the Greek and Turkish LVDs with the IAG conventional value recently proposed

Micromachined electrostatic vertical actuator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Abraham P.; Sommargren, Gary E.; McConaghy, Charles F.

A micromachined vertical actuator utilizing a levitational force, such as in electrostatic comb drives, provides vertical actuation that is relatively linear in actuation for control, and can be readily combined with parallel plate capacitive position sensing for position control. The micromachined electrostatic vertical actuator provides accurate movement in the sub-micron to micron ranges which is desirable in the phase modulation instrument, such as optical phase shifting. For example, compact, inexpensive, and position controllable micromirrors utilizing an electrostatic vertical actuator can replace the large, expensive, and difficult-to-maintain piezoelectric actuators. A thirty pound piezoelectric actuator with corner cube reflectors, as utilized inmore » a phase shifting diffraction interferometer can be replaced with a micromirror and a lens. For any very precise and small amplitudes of motion` micromachined electrostatic actuation may be used because it is the most compact in size, with low power consumption and has more straightforward sensing and control options.« less

Micromachined electrostatic vertical actuator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, A.P.; Sommargren, G.E.; McConaghy, C.F.

A micromachined vertical actuator utilizing a levitational force, such as in electrostatic comb drives, provides vertical actuation that is relatively linear in actuation for control, and can be readily combined with parallel plate capacitive position sensing for position control. The micromachined electrostatic vertical actuator provides accurate movement in the sub-micron to micron ranges which is desirable in the phase modulation instrument, such as optical phase shifting. For example, compact, inexpensive, and position controllable micromirrors utilizing an electrostatic vertical actuator can replace the large, expensive, and difficult-to-maintain piezoelectric actuators. A thirty pound piezoelectric actuator with corner cube reflectors, as utilized inmore » a phase shifting diffraction interferometer can be replaced with a micromirror and a lens. For any very precise and small amplitudes of motion, micromachined electrostatic actuation may be used because it is the most compact in size, with low power consumption and has more straightforward sensing and control options.« less

Description of an oral Chagas disease outbreak in Venezuela, including a vertically transmitted case.

PubMed

Noya, Belkisyolé Alarcón de; Pérez-Chacón, Gladymar; Díaz-Bello, Zoraida; Dickson, Sonia; Muñoz-Calderón, Arturo; Hernández, Carlos; Pérez, Yadira; Mauriello, Luciano; Moronta, Eyleen

2017-08-01

We describe the eleventh major outbreak of foodborne Trypanosoma cruzi transmission in urban Venezuela, including evidence for vertical transmission from the index case to her fetus. After confirming fetal death at 24 weeks of gestation, pregnancy interruption was performed. On direct examination of the amniotic fluid, trypomastigotes were detected. T. cruzi specific-polymerase chain reaction (PCR) also proved positive when examining autopsied fetal organs. Finally, microscopic fetal heart examination revealed amastigote nests. Acute orally transmitted Chagas disease can be life threatening or even fatal for pregnant women and unborn fetuses owing to vertical transmission. There is therefore an urgent need to improve national epidemiologic control measures.

46 CFR 108.160 - Vertical ladders.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Construction and Arrangement Means of Escape § 108.160 Vertical ladders. (a) Each vertical ladder must have... vertical fixed ladders may be made of wood. [CGD 73-251, 43 FR 56808, Dec. 4, 1978, as amended by USCG-2002...

Vertical axis wind turbine airfoil

DOEpatents

Krivcov, Vladimir; Krivospitski, Vladimir; Maksimov, Vasili; Halstead, Richard; Grahov, Jurij Vasiljevich

2012-12-18

A vertical axis wind turbine airfoil is described. The wind turbine airfoil can include a leading edge, a trailing edge, an upper curved surface, a lower curved surface, and a centerline running between the upper surface and the lower surface and from the leading edge to the trailing edge. The airfoil can be configured so that the distance between the centerline and the upper surface is the same as the distance between the centerline and the lower surface at all points along the length of the airfoil. A plurality of such airfoils can be included in a vertical axis wind turbine. These airfoils can be vertically disposed and can rotate about a vertical axis.

The Last Appearance Datum of Hipparion in Western Europe: magnetostratigraphy along the Pliocene-Pleistocene boundary in the Villarroya Basin (Northern Spain)

NASA Astrophysics Data System (ADS)

Pueyo, Emilio L.; Muñoz, Arsenio; Laplana, César; Parés, Josep M.

2016-11-01

The Villarroya Basin in Northern Spain contains one of the classic Villafranchian localities of Europe and allows about 100 m of sediments to be explored by magnetostratigraphic techniques. Besides, the occurrence of some other macro- and micro-mammifera fossils becomes Villarroya in one of the most important Villafranchian localities of Southern Europe. Therefore, we have sampled two sections (one contains the classic locality) to shed some light on its chronostratigraphy. Detailed stepwise demagnetization has revealed primary and reliable directions (carried by magnetite and hematite) in more than 250 samples and allows us building a robust local polarity scale. The correlation with the geologic time scale locates the local sequence along the Gauss and Matuyama chrons. A Réunion chron (C2r.1n) equivalent age (2.128-2.148 Ma) is here proposed for the Villarroya fossil locality since it is clearly located above the Gauss/Matuyama boundary (very well defined in the magnetostratigraphic section) and displays normal polarity. This correlation implies a new age assignment for the classic paleontological fossil locality of Villarroya and a Last Appearance Datum of Hipparion sensu lato in Western Europe significantly younger than previously established. Taking into account this new dating, the Hipparion and Equus horses could have coexisted in Europe up to the complete extinction of Hipparion in early Matuyama times.

Vertical electromagnetic profiling (VEMP)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lytle, R.J.

1984-08-01

Vertical seismic profiling (VSP) is based upon reception measurements performed in a borehole with a source near the ground surface. This technology has seen a surge in application and development in the last decade. The analogous concept of vertical electromagnetic profiling (VEMP) consists of reception measurements performed in a borehole with a source near the ground surface. Although the electromagnetic concept has seen some application, this technology has not been as systematically developed and applied as VSP. Vertical electromagnetic profiling provides distinct and complementary data due to sensing different physical parameters than seismic profiling. Certain of the advantages of VEMPmore » are presented. 28 references, 7 figures.« less

Vertical sounding balloons for stratospheric photochemistry

NASA Astrophysics Data System (ADS)

Pommereau, J. P.

The use of vertical sounding balloons for stratospheric photochemistry studies is illustrated by the use of a vertical piloted gas balloon for the search of NO2 diurnal variations. It is shown that the use of montgolfieres (hot air balloons) can enhance the vertical sounding technique. Particular attention is given to a sun-heated montgolfiere and to the more sophisticated infrared montgolfiere that is able to perform three to four vertical excursions per day and to remain aloft for weeks or months.

Metal Oxide Vertical Graphene Hybrid Supercapacitors

NASA Technical Reports Server (NTRS)

Meyyappan, Meyya (Inventor)

2018-01-01

A metal oxide vertical graphene hybrid supercapacitor is provided. The supercapacitor includes a pair of collectors facing each other, and vertical graphene electrode material grown directly on each of the pair of collectors without catalyst or binders. A separator may separate the vertical graphene electrode materials.

Vertical position of the orbits in nonsyndromic plagiocephaly in childhood and its relation to vertical strabismus.

PubMed

Eveleens, Jordi R J; Mathijssen, Irene M; Lequin, Maarten H; Polling, Jan-Roelof; Looman, Caspar W N; Simonsz, Huibert J

2011-01-01

To determine the existence of a correlation between the vertical angle of strabismus and the vertical angle between the orbital axes in nonsyndromic plagiocephaly in childhood. Patients were included when diagnosed with plagiocephaly. Orthoptic measurements showed a vertical strabismus and three-dimensional computed tomographic (CT) imaging of the skull was available. Patients were excluded if plagiocephaly was part of a syndrome or if any surgical intervention had taken place before our measurements. Three-dimensional CT imaging was used to calculate the vertical angle between the orbital axes in 3 reference planes (VAO) perpendicular to a line of reference through the lower borders of the maxilla (VAOmax), both auditory canals (VAOaud), and the lower points of the external occipital protuberances (VAOocc). Fourteen patients were included (mean age, 14 mo). Three-dimensional CT measurements showed a mean (SD) VAOmax of 1.70 (2.31) degrees, VAOaud of -1.54 (1.46) degrees, and VAOocc of -2.06 (4.29) degrees (a negative value indicates that the eye on the affected side was situated lower in the head). The mean vertical angle of strabismus was -2.39 (4.69) degrees in gaze toward the affected side, 3.66 (3.77) degrees in gaze ahead, and 8.14 (5.63) degrees in gaze toward the nonaffected side. The Pearson test showed no significant correlations. The clinical observation that vertical strabismus in adult plagiocephaly is correlated with the vertical angle of the orbital axes could not be confirmed in young children.

15 CFR Appendix II to Subpart P of... - Existing Management Areas Boundary Coordinates

Code of Federal Regulations, 2014 CFR

2014-01-01

....43.8′ N 81 deg.48.6′ W. Key West National Wildlife Refuge [Based on the North American Datum of 1983... COMMERCE OCEAN AND COASTAL RESOURCE MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Florida Keys... Administration Key Largo-Management Area [Based on differential Global Positioning Systems data] Point Latitude...

15 CFR Appendix II to Subpart P of... - Existing Management Areas Boundary Coordinates

Code of Federal Regulations, 2011 CFR

2011-01-01

....43.8′ N 81 deg.48.6′ W. Key West National Wildlife Refuge [Based on the North American Datum of 1983... COMMERCE OCEAN AND COASTAL RESOURCE MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Florida Keys... Administration Key Largo-Management Area [Based on differential Global Positioning Systems data] Point Latitude...

15 CFR Appendix II to Subpart P of... - Existing Management Areas Boundary Coordinates

Code of Federal Regulations, 2010 CFR

2010-01-01

....43.8′ N 81 deg.48.6′ W. Key West National Wildlife Refuge [Based on the North American Datum of 1983... COMMERCE OCEAN AND COASTAL RESOURCE MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Florida Keys... Administration Key Largo-Management Area [Based on differential Global Positioning Systems data] Point Latitude...

15 CFR Appendix II to Subpart P of... - Existing Management Areas Boundary Coordinates

Code of Federal Regulations, 2013 CFR

2013-01-01

....43.8′ N 81 deg.48.6′ W. Key West National Wildlife Refuge [Based on the North American Datum of 1983... COMMERCE OCEAN AND COASTAL RESOURCE MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Florida Keys... Administration Key Largo-Management Area [Based on differential Global Positioning Systems data] Point Latitude...

15 CFR Appendix II to Subpart P of... - Existing Management Areas Boundary Coordinates

Code of Federal Regulations, 2012 CFR

2012-01-01

....43.8′ N 81 deg.48.6′ W. Key West National Wildlife Refuge [Based on the North American Datum of 1983... COMMERCE OCEAN AND COASTAL RESOURCE MANAGEMENT NATIONAL MARINE SANCTUARY PROGRAM REGULATIONS Florida Keys... Administration Key Largo-Management Area [Based on differential Global Positioning Systems data] Point Latitude...

Department of Defense Strategy to Support Multi-Agency Bat Conservation Initiative within the State of Utah

DTIC Science & Technology

2008-02-28

Range, and Section are entered. Datum: Geometric reference surface. Original Site Location datum is defined by user’s map datum; e.g. NAD27...Section are entered. Datum: Geometric reference surface. Original Site Location datum is defined by user’s map datum; e.g. NAD27 Conus or NAD83...Calculated and recorded automatically if the fields UTM_N and UTM_E or Township, Range, and Section are entered. 41 Datum: Geometric reference surface

Acute Improvement of Vertical Jump Performance After Isometric Squats Depends on Knee Angle and Vertical Jumping Ability.

PubMed

Tsoukos, Athanasios; Bogdanis, Gregory C; Terzis, Gerasimos; Veligekas, Panagiotis

2016-08-01

Tsoukos, A, Bogdanis, GC, Terzis, G, and Veligekas, P. Acute improvement of vertical jump performance after isometric squats depends on knee angle and vertical jumping ability. J Strength Cond Res 30(8): 2250-2257, 2016-This study examined the acute effects of maximum isometric squats at 2 different knee angles (90 or 140°) on countermovement jump (CMJ) performance in power athletes. Fourteen national-level male track and field power athletes completed 3 main trials (2 experimental and 1 control) in a randomized and counterbalanced order 1 week apart. Countermovement jump performance was evaluated using a force-plate before and 15 seconds, 3, 6, 9, and 12 minutes after 3 sets of 3 seconds maximum isometric contractions with 1-minute rest in between, from a squat position with knee angle set at 90 or 140°. Countermovement jump performance was improved compared with baseline only in the 140° condition by 3.8 ± 1.2% on the 12th minute of recovery (p = 0.027), whereas there was no change in CMJ height in the 90° condition. In the control condition, there was a decrease in CMJ performance over time, reaching -3.6 ± 1.2% (p = 0.049) after 12 minutes of recovery. To determine the possible effects of baseline jump performance on subsequent CMJ performance, subjects were divided into 2 groups ("high jumpers" and "low jumpers"). The baseline CMJ values of "high jumpers" and "low jumpers" differed significantly (CMJ: 45.1 ± 2.2 vs. 37.1 ± 3.9 cm, respectively, p = 0.001). Countermovement jump was increased only in the "high jumpers" group by 5.4 ± 1.4% (p = 0.001) and 7.4 ± 1.2% (p = 0.001) at the knee angles of 90 and 140°, respectively. This improvement was larger at the 140° angle (p = 0.049). Knee angle during isometric squats and vertical jumping ability are important determinants of the acute CMJ performance increase observed after a conditioning activity.

Evaluation of vertical coordinate and vertical mixing algorithms in the HYbrid-Coordinate Ocean Model (HYCOM)

NASA Astrophysics Data System (ADS)

Halliwell, George R.

Vertical coordinate and vertical mixing algorithms included in the HYbrid Coordinate Ocean Model (HYCOM) are evaluated in low-resolution climatological simulations of the Atlantic Ocean. The hybrid vertical coordinates are isopycnic in the deep ocean interior, but smoothly transition to level (pressure) coordinates near the ocean surface, to sigma coordinates in shallow water regions, and back again to level coordinates in very shallow water. By comparing simulations to climatology, the best model performance is realized using hybrid coordinates in conjunction with one of the three available differential vertical mixing models: the nonlocal K-Profile Parameterization, the NASA GISS level 2 turbulence closure, and the Mellor-Yamada level 2.5 turbulence closure. Good performance is also achieved using the quasi-slab Price-Weller-Pinkel dynamical instability model. Differences among these simulations are too small relative to other errors and biases to identify the "best" vertical mixing model for low-resolution climate simulations. Model performance deteriorates slightly when the Kraus-Turner slab mixed layer model is used with hybrid coordinates. This deterioration is smallest when solar radiation penetrates beneath the mixed layer and when shear instability mixing is included. A simulation performed using isopycnic coordinates to emulate the Miami Isopycnic Coordinate Ocean Model (MICOM), which uses Kraus-Turner mixing without penetrating shortwave radiation and shear instability mixing, demonstrates that the advantages of switching from isopycnic to hybrid coordinates and including more sophisticated turbulence closures outweigh the negative numerical effects of maintaining hybrid vertical coordinates.

Estimating Coastal Digital Elevation Model (DEM) Uncertainty

NASA Astrophysics Data System (ADS)

Amante, C.; Mesick, S.

2017-12-01

Integrated bathymetric-topographic digital elevation models (DEMs) are representations of the Earth's solid surface and are fundamental to the modeling of coastal processes, including tsunami, storm surge, and sea-level rise inundation. Deviations in elevation values from the actual seabed or land surface constitute errors in DEMs, which originate from numerous sources, including: (i) the source elevation measurements (e.g., multibeam sonar, lidar), (ii) the interpolative gridding technique (e.g., spline, kriging) used to estimate elevations in areas unconstrained by source measurements, and (iii) the datum transformation used to convert bathymetric and topographic data to common vertical reference systems. The magnitude and spatial distribution of the errors from these sources are typically unknown, and the lack of knowledge regarding these errors represents the vertical uncertainty in the DEM. The National Oceanic and Atmospheric Administration (NOAA) National Centers for Environmental Information (NCEI) has developed DEMs for more than 200 coastal communities. This study presents a methodology developed at NOAA NCEI to derive accompanying uncertainty surfaces that estimate DEM errors at the individual cell-level. The development of high-resolution (1/9th arc-second), integrated bathymetric-topographic DEMs along the southwest coast of Florida serves as the case study for deriving uncertainty surfaces. The estimated uncertainty can then be propagated into the modeling of coastal processes that utilize DEMs. Incorporating the uncertainty produces more reliable modeling results, and in turn, better-informed coastal management decisions.

A 34-meter VAWT (Vertical Axis Wind Turbine) point design

NASA Astrophysics Data System (ADS)

Ashwill, T. D.; Berg, D. E.; Dodd, H. M.; Rumsey, M. A.; Sutherland, H. J.; Veers, P. S.

The Wind Energy Division at Sandia National Laboratories recently completed a point design based on the 34-m Vertical Axis Wind Turbine (VAWT) Test Bed. The 34-m Test Bed research machine incorporates several innovations that improve Darrieus technology, including increased energy production, over previous machines. The point design differs minimally from the Test Bed; but by removing research-related items, its estimated cost is substantially reduced. The point design is a first step towards a Test-Bed-based commercial machine that would be competitive with conventional sources of power in the mid-1990s.

Simulations of the Richtmyer-Meshkov Instability in a two-shock vertical shock tube

NASA Astrophysics Data System (ADS)

Ferguson, Kevin; Olson, Britton; Jacobs, Jeffrey

2017-11-01

Simulations of the Richtmyer-Meshkov Instability (RMI) in a new two-shock vertical shock tube configuration are presented. The simulations are performed using the ARES code at Lawrence-Livermore National Laboratory (LLNL). Two M=1.2 shock waves travel in opposing directions and impact an initially stationary interface formed by sulfur hexaflouride (SF6) and air. The delay between the two shocks is controlled to achieve a prescribed temporal separation in shock wave arrival time. Initial interface perturbations and diffusion profiles are generated in keeping with previously gathered experimental data. The effect of varying the inter-shock delay and initial perturbation structure on instability growth and mixing parameters is examined. Information on the design, construction, and testing of a new two-shock vertical shock tube are also presented.

Maine coastal storm and flood of February 2, 1976

USGS Publications Warehouse

Morrill, Richard Arthur; Chin, Edwin H.; Richardson, W.S.

1979-01-01

A business section of Bangor, Maine, was flooded with 12 feet (3.7 m) of water on February 2, 1976. The water surface elevation reached 17.46 feet (5.32 m) above national geodetic vertical datum of 1929 (NGVD), approximately 10.5 feet (3.2 m) above the predicted astronomical tide at Bangor. The unusually high water resulted from a tidal storm surge caused by prolonged strong, south-southeasterly winds which occurred near the time of astronomical high tide. Winds exceeded 64 knots off the New England coast. The resulting flood was the third highest since 1846 and is the first documented tidal flood at Bangor. This report documents the meteorological and hydrologic conditions associated with the flooding and also contains a brief description of storm damage from Eastport to Brunswick, Maine. Included are flood elevations in the city of Bangor and along the coast of Maine east of the Kennebec River. (Kosco-USGS)

A precise vertical network: Establishing new orthometric heights with static surveys in Florida tidal marshes

USGS Publications Warehouse

Raabe, E.A.; Stumpf, R.P.; Marth, N.J.; Shrestha, R.L.

1996-01-01

Elevation differences on the order of 10 cm within Florida's marsh system influence major variations in tidal flooding and in the associated plant communities. This low elevation gradient combined with sea level fluctuation of 5-to-10 cm over decadel and longer periods can generate significant alteration and erosion of marsh habitats along the Gulf Coast. Knowledge of precise and accurate elevations in the marsh is critical to the efficient monitoring and management of these habitats. Global positioning system (GPS) technology was employed to establish six new orthometric heights along the Gulf Coast from which kinematic surveys into the marsh interior are conducted. The vertical accuracy achieved using GPS technology was evaluated using two networks with 16 vertical and nine horizontal NGS published high accuracy positions. New positions were occupied near St. Marks National Wildlife Refuge and along the coastline of Levy County and Citrus County. Static surveys were conducted using four Ashtech dual frequency P-code receivers for 45-minute sessions and a data logging rate of 10 seconds. Network vector lengths ranged from 4 to 64 km and, including redundant baselines, totaled over 100 vectors. Analysis includes use of the GEOID93 model with a least squares network adjustment and reference to the National Geodetic Reference System (NGRS). The static surveys show high internal consistency and the desired centimeter-level accuracy is achieved for the local network. Uncertainties for the newly established vertical positions range from 0.8 cm to 1.8 cm at the 95% confidence level. These new positions provide sufficient vertical accuracy to achieve the project objectives of tying marsh surface elevations to long-term water level gauges recording sea level fluctuations along the coast.

A Physician's Perspective On Vertical Integration.

PubMed

Berenson, Robert A

2017-09-01

Vertical integration has been a central feature of health care delivery system change for more than two decades. Recent studies have demonstrated that vertically integrated health care systems raise prices and costs without observable improvements in quality, despite many theoretical reasons why cost control and improved quality might occur. Less well studied is how physicians view their newfound partnerships with hospitals. In this article I review literature findings and other observations on five aspects of vertical integration that affect physicians in their professional and personal lives: patients' access to physicians, physician compensation, autonomy versus system support, medical professionalism and culture, and lifestyle. I conclude that the movement toward physicians' alignment with and employment in vertically integrated systems seems inexorable but that policy should not promote such integration either intentionally or inadvertently. Instead, policy should address the flaws in current payment approaches that reward high prices and excessive service use-outcomes that vertical integration currently produces. Project HOPE—The People-to-People Health Foundation, Inc.

Publications - RI 2000-1D | Alaska Division of Geological & Geophysical

Science.gov Websites

Tidal Datum Portal Climate and Cryosphere Hazards Coastal Hazards Program Guide to Geologic Hazards in - Read me Keywords Arctic National Wildlife Refuge; Aufeis; Brooks Range; Coastal and River; Coastal and

Vertical structures in vibrated wormlike micellar solutions

NASA Astrophysics Data System (ADS)

Epstein, Tamir; Deegan, Robert

2008-11-01

Vertically vibrated shear thickening particulate suspensions can support a free-standing interfaces oriented parallel to gravity. We find that shear thickening worm-like micellar solutions also support such vertical interfaces. Above a threshold in acceleration, the solution spontaneously accumulates into a labyrinthine pattern characterized by a well-defined vertical edge. The formation of vertical structures is of interest because they are unique to shear-thickening fluids, and they indicate the existence of an unknown stress bearing mechanism.

Processing vertical size disparities in distinct depth planes.

PubMed

Duke, Philip A; Howard, Ian P

2012-08-17

A textured surface appears slanted about a vertical axis when the image in one eye is horizontally enlarged relative to the image in the other eye. The surface appears slanted in the opposite direction when the same image is vertically enlarged. Two superimposed textured surfaces with different horizontal size disparities appear as two surfaces that differ in slant. Superimposed textured surfaces with equal and opposite vertical size disparities appear as a single frontal surface. The vertical disparities are averaged. We investigated whether vertical size disparities are averaged across two superimposed textured surfaces in different depth planes or whether they induce distinct slants in the two depth planes. In Experiment 1, two superimposed textured surfaces with different vertical size disparities were presented in two depth planes defined by horizontal disparity. The surfaces induced distinct slants when the horizontal disparity was more than ±5 arcmin. Thus, vertical size disparities are not averaged over surfaces with different horizontal disparities. In Experiment 2 we confirmed that vertical size disparities are processed in surfaces away from the horopter, so the results of Experiment 1 cannot be explained by the processing of vertical size disparities in a fixated surface only. Together, these results show that vertical size disparities are processed separately in distinct depth planes. The results also suggest that vertical size disparities are not used to register slant globally by their effect on the registration of binocular direction of gaze.

Low voltage operation of GaN vertical nanowire MOSFET

NASA Astrophysics Data System (ADS)

Son, Dong-Hyeok; Jo, Young-Woo; Seo, Jae Hwa; Won, Chul-Ho; Im, Ki-Sik; Lee, Yong Soo; Jang, Hwan Soo; Kim, Dae-Hyun; Kang, In Man; Lee, Jung-Hee

2018-07-01

GaN gate-all-around (GAA) vertical nanowire MOSFET (VNWMOSFET) with channel length of 300 nm and diameter of 120 nm, the narrowest GaN-based vertical nanowire transistor ever achieved from the top-down approach, was fabricated by utilizing anisotropic side-wall wet etching in TMAH solution and photoresist etch-back process. The VNWMOSFET exhibited output characteristics with very low saturation drain voltage of less than 0.5 V, which is hardly observed from the wide bandgap-based devices. Simulation results indicated that the narrow diameter of the VNWMOSFET with relatively short channel length is responsible for the low voltage operation. The VNWMOSFET also demonstrated normally-off mode with threshold voltage (VTH) of 0.7 V, extremely low leakage current of ∼10-14 A, low drain-induced barrier lowering (DIBL) of 125 mV/V, and subthreshold swing (SS) of 66-122 mV/decade. The GaN GAA VNWMOSFET with narrow channel diameter investigated in this work would be promising for new low voltage logic application. He has been a Professor with the School of Electrical Engineering and Computer Science, Kyungpook National University, Daegu, Korea, since 1993

Vertical Structure of Radiation-pressure-dominated Thin Disks: Link between Vertical Advection and Convective Stability

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gong, Hong-Yu; Gu, Wei-Min, E-mail: guwm@xmu.edu.cn

2017-04-20

In the classic picture of standard thin accretion disks, viscous heating is balanced by radiative cooling through the diffusion process, and the radiation-pressure-dominated inner disk suffers convective instability. However, recent simulations have shown that, owing to the magnetic buoyancy, the vertical advection process can significantly contribute to energy transport. In addition, in comparing the simulation results with the local convective stability criterion, no convective instability has been found. In this work, following on from simulations, we revisit the vertical structure of radiation-pressure-dominated thin disks and include the vertical advection process. Our study indicates a link between the additional energy transportmore » and the convectively stable property. Thus, the vertical advection not only significantly contributes to the energy transport, but it also plays an important role in making the disk convectively stable. Our analyses may help to explain the discrepancy between classic theory and simulations on standard thin disks.« less

The Use of GOCE/GRACE Information in the Latest NGS xGeoid15 Model for the USA

NASA Astrophysics Data System (ADS)

Holmes, S. A.; Li, X.; Youngman, M.

2015-12-01

The U.S. National Geodetic Survey [NGS], through its Gravity for the Redefinition of the American Vertical Datum [GRAV-D] program, is flying airborne gravity surveys over the USA and its territories. By 2022, NGS intends that all orthometric heights in the USA will be determined in the field using a reliable national gravimetric geoid model to transform from geodetic heights obtained from GPS. Towards this end, all available airborne data has been incorporated into a new NGS experimental geoid model - xGEOID15. The xGEOID15 model is the second in a series of annual experimental geoid models that incorporates NGS GRAV-D airborne data. This series provides a useful benchmark for assessing and improving current techniques, to ultimately compute a geoid model that can support a national physical height system by 2022. Here, we focus on the combination of the latest GOCE/GRACE models with the terrestrial gravimetry (land/airborne) that was applied for xGeoid15. Comparisons against existing combination gravitational solutions, such as EGM2008 and EIGEN6C4, as well as recent geoid models, such as xGeoid14 and CGG2013, are interesting for what they reveal about the respective use of the GOCE/GRACE satgrav information.

Vertical Lift - Not Just For Terrestrial Flight

NASA Technical Reports Server (NTRS)

Young, Larry A

2000-01-01

Autonomous vertical lift vehicles hold considerable potential for supporting planetary science and exploration missions. This paper discusses several technical aspects of vertical lift planetary aerial vehicles in general, and specifically addresses technical challenges and work to date examining notional vertical lift vehicles for Mars, Titan, and Venus exploration.

Measuring Growth with Vertical Scales

ERIC Educational Resources Information Center

Briggs, Derek C.

2013-01-01

A vertical score scale is needed to measure growth across multiple tests in terms of absolute changes in magnitude. Since the warrant for subsequent growth interpretations depends upon the assumption that the scale has interval properties, the validation of a vertical scale would seem to require methods for distinguishing interval scales from…

Learning to Read Vertical Text in Peripheral Vision

PubMed Central

Subramanian, Ahalya; Legge, Gordon E.; Wagoner, Gunther Harrison; Yu, Deyue

2014-01-01

Purpose English–language text is almost always written horizontally. Text can be formatted to run vertically, but this is seldom used. Several studies have found that horizontal text can be read faster than vertical text in the central visual field. No studies have investigated the peripheral visual field. Studies have also concluded that training can improve reading speed in the peripheral visual field for horizontal text. We aimed to establish whether the horizontal vertical differences are maintained and if training can improve vertical reading in the peripheral visual field. Methods Eight normally sighted young adults participated in the first study. Rapid Serial Visual Presentation (RSVP) reading speed was measured for horizontal and vertical text in the central visual field and at 10° eccentricity in the upper or lower (horizontal text), and right or left (vertical text) visual fields. Twenty-one normally sighted young adults split equally between 2 training and 1 control group participated in the second study. Training consisted of RSVP reading either using vertical text in the left visual field or horizontal text in the inferior visual field. Subjects trained daily over 4 days. Pre and post horizontal and vertical RSVP reading speeds were carried out for all groups. For the training groups these measurements were repeated 1 week and 1 month post training. Results Prior to training, RSVP reading speeds were faster for horizontal text in the central and peripheral visual fields when compared to vertical text. Training vertical reading improved vertical reading speeds by an average factor of 2.8. There was partial transfer of training to the opposite (right) hemifield. The training effects were retained for up to a month. Conclusions RSVP training can improve RSVP vertical text reading in peripheral vision. These findings may have implications for patients with macular degeneration or hemianopic field loss. PMID:25062130

An Overview of Active Flow Control Enhanced Vertical Tail Technology Development

NASA Technical Reports Server (NTRS)

Lin, John C.; Andino, Marlyn Y.; Alexander, Michael G.; Whalen, Edward A.; Spoor, Marc A.; Tran, John T.; Wygnanski, Israel J.

2016-01-01

This paper summarizes a joint NASA/Boeing research effort to advance Active Flow Control (AFC) technology to enhance aerodynamic efficiency of a vertical tail. Sweeping jet AFC technology was successfully tested on subscale and full-scale models as well as in flight. The subscale test was performed at Caltech on a 14% scale model. More than 50% side force enhancement was achieved by the sweeping jet actuation when the momentum coefficient was 1.7%. AFC caused significant increases in suction pressure on the actuator side and associated side force enhancement. Subsequently, a full-scale Boeing 757 vertical tail model equipped with sweeping jets was tested at the National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel at NASA Ames Research Center. There, flow separation control optimization was performed at near flight conditions. Greater than 20% increase in side force were achieved for the maximum rudder deflection of 30deg at the key sideslip angles (0deg and -7.5deg) with a 31-actuator AFC configuration. Based on these tests, the momentum coefficient is shown to be a necessary, but not sufficient parameter to use for design and scaling of sweeping jet AFC from subscale tests to full-scale applications. Leveraging the knowledge gained from the wind tunnel tests, the AFC-enhanced vertical tail technology was successfully flown on the Boeing 757 ecoDemonstrator in the spring of 2015.

Thermal Impacts of Vertical Greenery Systems

NASA Astrophysics Data System (ADS)

Safikhani, Tabassom; Abdullah, Aminatuzuhariah Megat; Ossen, Dilshan Remaz; Baharvand, Mohammad

2014-12-01

- Using vertical greenery systems to reduce heat transmission is becoming more common in modern architecture. Vertical greenery systems are divided into two main categories; green facades and living walls. This study aims to examine the thermal performance of vertical greenery systems in hot and humid climates. An experimental procedure was used to measure indoor temperature and humidity. These parameters were also measured for the gap between the vertical greenery systems and wall surfaces. Three boxes were used as small-scale rooms. Two boxes were provided with either a living wall or a green facade and one box did not have any greenery (benchmark). Blue Trumpet Vine was used in the vertical greenery systems. The data were recorded over the course of three sunny days in April 2013. An analyses of the results showed that the living wall and green facade reduced indoor temperature up to 4.0 °C and 3.0 °C, respectively. The living wall and green facade also reduced cavity temperatures by 8.0 °C and 6.5 °C, respectively.

NGS' GRAV-D Project Brings Advances in Aerogravimetry

NASA Astrophysics Data System (ADS)

Childers, V. A.; Preaux, S. A.; Diehl, T. M.; Li, X.; Weil, C.

2011-12-01

NOAA's National Geodetic Survey has undertaken an extensive airborne gravity campaign to help replace the nation's vertical datum by 2022. After receiving Congressional funding in FY10 &11, the GRAV-D project has now surveyed 13.45% of the total area (as of abstract submittal time). The survey has now worked on a number of aircraft, both jets and turboprops. Early work was performed at 35,000 ft and 280 kts. Since summer of 2009, the survey altitude has been lowered to 20,000 ft to enhance signal recovery and to reduce the amplitude enhancement of noise in the downward continuation needed for gravity field blending. The high altitude and speed of the survey has forced a re-evaluation of all aspects of the airborne gravity processing methodology. This presentation will update the community on the progress of the project, summarize the various processing improvements implemented, and discuss the magnitude of their effects. Improvements and research include: a new in-house gravity processing software package called "Newton", kinematic GPS processing variables and their impacts on final gravity products, and evaluation of gravimeter off-level corrections, among other topics.

National geodetic satellite program, part 2

NASA Technical Reports Server (NTRS)

Schmid, H.

1977-01-01

Satellite geodesy and the creation of worldwide geodetic reference systems is discussed. The geometric description of the surface and the analytical description of the gravity field of the earth by means of worldwide reference systems, with the aid of satellite geodesy, are presented. A triangulation method based on photogrammetric principles is described in detail. Results are derived in the form of three dimensional models. These mathematical models represent the frame of reference into which one can fit the existing geodetic results from the various local datums, as well as future measurements.

Proposed stratotype for the base of the highest Cambrian stage at the first appearance datum of Cordylodus andresi, Lawson Cove section, Utah, USA

USGS Publications Warehouse

Miller, J.F.; Ethington, Raymond L.; Evans, K.R.; Holmer, L.E.; Loch, James D.; Popov, L.E.; Repetski, J.E.; Ripperdan, R.L.; Taylor, John F.

2006-01-01

We propose a candidate for the Global Standard Stratotype-section and Point (GSSP) for the base of the highest stage of the Furongian Series of the Cambrian System. The section is at Lawson Cove in the Ibex area of Millard County, Utah, USA. The marker horizon is the first appearance datum (FAD) of the conodont Cordylodus andresi Viira et Sergeyeva in Kaljo et al. [Kaljo, D., Borovko, N., Heinsalu, H., Khazanovich, K., Mens, K., Popov, L., Sergeyeva, S., Sobolevskaya, R., Viira, V., 1986. The Cambrian-Ordovician boundary in the Baltic-Ladoga clint area (North Estonia and Leningrad Region, USSR). Eesti NSV Teaduste Akadeemia Toimetised. Geologia 35, 97-108]. At this section and elsewhere this horizon also is the FAD of the trilobite Eurekia apopsis (Winston et Nicholls, 1967). This conodont characterizes the base of the Cordylodus proavus Zone, which has been recognized in many parts of the world. This trilobite characterizes the base of the Eurekia apopsis Zone, which has been recognized in many parts of North America. The proposed boundary is 46.7 m above the base of the Lava Dam Member of the Notch Peak Formation at the Lawson Cove section. Brachiopods, sequence stratigraphy, and carbon-isotope geochemistry are other tools that characterize this horizon and allow it to be recognized in other areas. ?? 2006 Nanjing Institute of Geology and Palaeontology, CAS.

Vertical transport of ozone and CO during super cyclones in the Bay of Bengal as detected by Tropospheric Emission Spectrometer.

PubMed

Fadnavis, S; Beig, G; Buchunde, P; Ghude, Sachin D; Krishnamurti, T N

2011-02-01

Vertical profiles of carbon monoxide (CO) and ozone retrieved from Tropospheric Emission Spectrometer have been analyzed during two super cyclone systems Mala and Sidr. Super cyclones Mala and Sidr traversed the Bay of Bengal (BOB) region on April 24-29, 2006 and November 12-16, 2007 respectively. The CO and ozone plume is observed as a strong enhancement of these pollutants in the upper troposphere over the BOB, indicating deep convective transport. Longitude-height cross-section of these pollutants shows vertical transport to the upper troposphere. CO mixing ratio ~90 ppb is observed near the 146-mb level during the cyclone Mala and near 316 mb during the cyclone Sidr. Ozone mixing ratio ~60-100 ppb is observed near the 316-mb level during both the cyclones. Analysis of National Centers for Environmental Prediction (NCEP) reanalysis vertical winds (omega) confirms vertical transport in the BOB.

The Gains from Vertical Scaling

ERIC Educational Resources Information Center

Briggs, Derek C.; Domingue, Ben

2013-01-01

It is often assumed that a vertical scale is necessary when value-added models depend upon the gain scores of students across two or more points in time. This article examines the conditions under which the scale transformations associated with the vertical scaling process would be expected to have a significant impact on normative interpretations…

Vertically aligned nanostructure scanning probe microscope tips

DOEpatents

Guillorn, Michael A.; Ilic, Bojan; Melechko, Anatoli V.; Merkulov, Vladimir I.; Lowndes, Douglas H.; Simpson, Michael L.

2006-12-19

Methods and apparatus are described for cantilever structures that include a vertically aligned nanostructure, especially vertically aligned carbon nanofiber scanning probe microscope tips. An apparatus includes a cantilever structure including a substrate including a cantilever body, that optionally includes a doped layer, and a vertically aligned nanostructure coupled to the cantilever body.

Geological implications of recently derived vertical velocities of benchmarks of the south-central United States of America

NASA Astrophysics Data System (ADS)

Dokka, R. K.

2005-05-01

It has been long-recognized that the south-central United States of America bordering the Gulf of Mexico (GOM) is actively subsiding, resulting in a slow, yet unrelenting inundation of the coast from south Texas to southwestern Alabama. Today's motions are but the latest chapter in the subsidence history of the GOM, a region that has accommodated the deposition of over 20 km of deltaic and continental margin sediments since mid Mesozoic time. Understanding the recent history of displacements and the processes responsible for subsidence are especially critical for near-term planning for coastal protection and restoration activities. Documentation of the true magnitude and geography of vertical motions of the surface through time has been hampered because previous measurement schemes did not employ reference datums of sufficient spatial and temporal precision. This situation has been somewhat improved recently through the recent analysis of National Geodetic Survey (NGS) 1st order leveling data from >2710 benchmarks in the region by Shinkle and Dokka (NOAA Technical Report 50 [2004]). That paper used original observations (not adjusted) and computed displacements and velocities related to NAVD88 for benchmarks visited during various leveling surveys from 1920 through 1995. Several important characteristics were observed and are summarized below. First, the data show that subsidence is not limited to areas of recent sediment accumulation such as the wetland areas of the modern delta (MRD) of the Mississippi River or its upstream alluvial valley (MAV), as supposed by most current syntheses. The entire coastal zone, as well as inland areas several hundred km from the shore, has subsided over the period of measurement. Regionally, vertical velocities range from less than -52 mm/yr in Louisiana to over +15 mm/yr in peripheral areas of eastern Mississippi-Alabama. The mean rate is ~-11 mm/yr in most coastal parishes of Louisiana. In the Mississippi River deltaic plain

Vertically stabilized elongated cross-section tokamak

DOEpatents

Sheffield, George V.

1977-01-01

This invention provides a vertically stabilized, non-circular (minor) cross-section, toroidal plasma column characterized by an external separatrix. To this end, a specific poloidal coil means is added outside a toroidal plasma column containing an endless plasma current in a tokamak to produce a rectangular cross-section plasma column along the equilibrium axis of the plasma column. By elongating the spacing between the poloidal coil means the plasma cross-section is vertically elongated, while maintaining vertical stability, efficiently to increase the poloidal flux in linear proportion to the plasma cross-section height to achieve a much greater plasma volume than could be achieved with the heretofore known round cross-section plasma columns. Also, vertical stability is enhanced over an elliptical cross-section plasma column, and poloidal magnetic divertors are achieved.

Relative net vertical impulse determines jumping performance.

PubMed

Kirby, Tyler J; McBride, Jeffrey M; Haines, Tracie L; Dayne, Andrea M

2011-08-01

The purpose of this investigation was to determine the relationship between relative net vertical impulse and jump height in a countermovement jump and static jump performed to varying squat depths. Ten college-aged males with 2 years of jumping experience participated in this investigation (age: 23.3 ± 1.5 years; height: 176.7 ± 4.5 cm; body mass: 84.4 ± 10.1 kg). Subjects performed a series of static jumps and countermovement jumps in a randomized fashion to a depth of 0.15, 0.30, 0.45, 0.60, and 0.75 m and a self-selected depth (static jump depth = 0.38 ± 0.08 m, countermovement jump depth = 0.49 ± 0.06 m). During the concentric phase of each jump, peak force, peak velocity, peak power, jump height, and net vertical impulse were recorded and analyzed. Net vertical impulse was divided by body mass to produce relative net vertical impulse. Increasing squat depth corresponded to a decrease in peak force and an increase in jump height and relative net vertical impulse for both static jump and countermovement jump. Across all depths, relative net vertical impulse was statistically significantly correlated to jump height in the static jump (r = .9337, p < .0001, power = 1.000) and countermovement jump (r = .925, p < .0001, power = 1.000). Across all depths, peak force was negatively correlated to jump height in the static jump (r = -0.3947, p = .0018, power = 0.8831) and countermovement jump (r = -0.4080, p = .0012, power = 0.9050). These results indicate that relative net vertical impulse can be used to assess vertical jump performance, regardless of initial squat depth, and that peak force may not be the best measure to assess vertical jump performance.

Predicting vertical jump height from bar velocity.

PubMed

García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

2015-06-01

The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s(-2)). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r(2) = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r(2) = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key pointsVertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer.The relationship between the point at which bar acceleration is less than -9.81 m·s(-2) and the real take-off is affected by the velocity of movement.Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance.

Predicting Vertical Jump Height from Bar Velocity

PubMed Central

García-Ramos, Amador; Štirn, Igor; Padial, Paulino; Argüelles-Cienfuegos, Javier; De la Fuente, Blanca; Strojnik, Vojko; Feriche, Belén

2015-01-01

The objective of the study was to assess the use of maximum (Vmax) and final propulsive phase (FPV) bar velocity to predict jump height in the weighted jump squat. FPV was defined as the velocity reached just before bar acceleration was lower than gravity (-9.81 m·s-2). Vertical jump height was calculated from the take-off velocity (Vtake-off) provided by a force platform. Thirty swimmers belonging to the National Slovenian swimming team performed a jump squat incremental loading test, lifting 25%, 50%, 75% and 100% of body weight in a Smith machine. Jump performance was simultaneously monitored using an AMTI portable force platform and a linear velocity transducer attached to the barbell. Simple linear regression was used to estimate jump height from the Vmax and FPV recorded by the linear velocity transducer. Vmax (y = 16.577x - 16.384) was able to explain 93% of jump height variance with a standard error of the estimate of 1.47 cm. FPV (y = 12.828x - 6.504) was able to explain 91% of jump height variance with a standard error of the estimate of 1.66 cm. Despite that both variables resulted to be good predictors, heteroscedasticity in the differences between FPV and Vtake-off was observed (r2 = 0.307), while the differences between Vmax and Vtake-off were homogenously distributed (r2 = 0.071). These results suggest that Vmax is a valid tool for estimating vertical jump height in a loaded jump squat test performed in a Smith machine. Key points Vertical jump height in the loaded jump squat can be estimated with acceptable precision from the maximum bar velocity recorded by a linear velocity transducer. The relationship between the point at which bar acceleration is less than -9.81 m·s-2 and the real take-off is affected by the velocity of movement. Mean propulsive velocity recorded by a linear velocity transducer does not appear to be optimal to monitor ballistic exercise performance. PMID:25983572

Fractographic Examination of the Vertical Stabilizer and Rudder from American Airlines Flight 587

NASA Technical Reports Server (NTRS)

Fox, Matthew R.; Schultheisz, Carl R.; Reeder, James R.

2005-01-01

The first major structural component failure of a composite part on a commercial airplane occurred during the crash of American Airlines Flight 587. The fractured composite lugs that attached the vertical stabilizer to the aircraft tail and the fractured composite honeycomb rudder were examined as part of the National Transportation Safety Board investigation of the accident. In this paper the composite fractures are described and the resulting clues to the failure events are discussed.

Retrieving Mesoscale Vertical Velocities along the Antarctic Circumpolar Current from a Combination of Satellite and In Situ Observations

NASA Astrophysics Data System (ADS)

Buongiorno Nardelli, B.; Iudicone, D.; Cotroneo, Y.; Zambianchi, E.; Rio, M. H.

2016-02-01

In the framework of the Italian National Program on Antarctic Research (PNRA), an analysis of the mesoscale dynamics along the Antarctic Circumpolar Current has been carried out starting from a combination of satellite and in situ observations. More specifically, state-of-the-art statistical techniques have been used to combine remotely-sensed sea surface temperature, salinity and absolute dynamical topography with in situ Argo data, providing mesoscale-resolving 3D tracers and geostrophic velocity fields. The 3D reconstruction has been validated with independent data collected during PNRA surveys. These data are then used to diagnose the vertical exchanges in the Southern Ocean through a generalized version of the Omega equation. Intense vertical motion (O(100 m/day)) is found along the ACC, upstream/downstream of its meanders, and within mesoscale eddies, where multipolar vertical velocity patterns are generally observed.

Neglected locked vertical patellar dislocation

PubMed Central

Gupta, Rakesh Kumar; Gupta, Vinay; Sangwan, Sukhbir Singh; Kamboj, Pradeep

2012-01-01

Patellar dislocations occurring about the vertical and horizontal axis are rare and irreducible. The neglected patellar dislocation is still rarer. We describe the clinical presentation and management of a case of neglected vertical patellar dislocation in a 6 year-old boy who sustained an external rotational strain with a laterally directed force to his knee. Initially the diagnosis was missed and 2 months later open reduction was done. The increased tension generated by the rotation of the lateral extensor retinaculum kept the patella locked in the lateral gutter even with the knee in full extension. Traumatic patellar dislocation with rotation around a vertical axis has been described earlier, but no such neglected case has been reported to the best of our knowledge. PMID:23162154

Recent vertical movements from precise levelling in the vicinity of the city of Basel, Switzerland

NASA Astrophysics Data System (ADS)

Schlatter, Andreas; Schneider, Dieter; Geiger, Alain; Kahle, Hans-Gert

2005-09-01

The southern end of the Upper Rhine Graben is one of the zones in Switzerland where recent crustal movements can be expected because of ongoing seismotectonic processes as witnessed by seismicity clusters occurring in this region. Therefore, in 1973 a control network with levelling profiles across the eastern Rhine Graben fault was installed and measured in the vicinity of the city of Basel in order to measure relative vertical movements and investigate their relationship with seismic events. As a contribution to EUCOR-URGENT, the profiles were observed a third time in the years 2002 and 2003 and connected to the Swiss national levelling network. The results of these local measurements are discussed in terms of accuracy and significance. Furthermore, they are combined and interpreted together with the extensive data set of recent vertical movements in Switzerland (Jura Mountains, Central Plateau and the Alps). In order to be able to prove height changes with precise levelling, their values should amount to at least 3 4 mm (1σ). The present investigations, however, have not shown any significant vertical movements over the past 30 years.

Aiding Vertical Guidance Understanding

NASA Technical Reports Server (NTRS)

Feary, Michael; McCrobie, Daniel; Alkin, Martin; Sherry, Lance; Polson, Peter; Palmer, Everett; McQuinn, Noreen

1998-01-01

A two-part study was conducted to evaluate modern flight deck automation and interfaces. In the first part, a survey was performed to validate the existence of automation surprises with current pilots. Results indicated that pilots were often surprised by the behavior of the automation. There were several surprises that were reported more frequently than others. An experimental study was then performed to evaluate (1) the reduction of automation surprises through training specifically for the vertical guidance logic, and (2) a new display that describes the flight guidance in terms of aircraft behaviors instead of control modes. The study was performed in a simulator that was used to run a complete flight with actual airline pilots. Three groups were used to evaluate the guidance display and training. In the training, condition, participants went through a training program for vertical guidance before flying the simulation. In the display condition, participants ran through the same training program and then flew the experimental scenario with the new Guidance-Flight Mode Annunciator (G-FMA). Results showed improved pilot performance when given training specifically for the vertical guidance logic and greater improvements when given the training and the new G-FMA. Using actual behavior of the avionics to design pilot training and FMA is feasible, and when the automated vertical guidance mode of the Flight Management System is engaged, the display of the guidance mode and targets yields improved pilot performance.

Solving vertical and horizontal well hydraulics problems analytically in Cartesian coordinates with vertical and horizontal anisotropies

NASA Astrophysics Data System (ADS)

Batu, Vedat

2012-01-01

SummaryA new generalized three-dimensional analytical solution is developed for a partially-penetrating vertical rectangular parallelepiped well screen in a confined aquifer by solving the three-dimensional transient ground water flow differential equation in x- y- z Cartesian coordinates system for drawdown by taking into account the three principal hydraulic conductivities ( Kx, Ky, and Kz) along the x- y- z coordinate directions. The fully penetrating screen case becomes equivalent to the single vertical fracture case of Gringarten and Ramey (1973). It is shown that the new solution and Gringarten and Ramey solution (1973) match very well. Similarly, it is shown that this new solution for a horizontally tiny fully penetrating parallelepiped rectangular parallelepiped screen case match very well with Theis (1935) solution. Moreover, it is also shown that the horizontally tiny partially-penetrating parallelepiped rectangular well screen case of this new solution match very well with Hantush (1964) solution. This new analytical solution can also cover a partially-penetrating horizontal well by representing its screen interval with vertically tiny rectangular parallelepiped. Also the solution takes into account both the vertical anisotropy ( azx = Kz/ Kx) as well as the horizontal anisotropy ( ayx = Ky/ Kx) and has potential application areas to analyze pumping test drawdown data from partially-penetrating vertical and horizontal wells by representing them as tiny rectangular parallelepiped as well as line sources. The solution has also potential application areas for a partially-penetrating parallelepiped rectangular vertical fracture. With this new solution, the horizontal anisotropy ( ayx = Ky/ Kx) in addition to the vertical anisotropy ( azx = Kz/ Kx) can also be determined using observed drawdown data. Most importantly, with this solution, to the knowledge of the author, it has been shown the first time in the literature that some well-known well hydraulics

Influence of maxillary posterior discrepancy on upper molar vertical position and facial vertical dimensions in subjects with or without skeletal open bite

PubMed Central

Aliaga-Del Castillo, Aron; Pérez-Vargas, Luis Fernando; Flores-Mir, Carlos

2016-01-01

Summary Objectives: To determine the influence of maxillary posterior discrepancy on upper molar vertical position and dentofacial vertical dimensions in individuals with or without skeletal open bite (SOB). Materials and methods: Pre-treatment lateral cephalograms of 139 young adults were examined. The sample was divided into eight groups categorized according to their sagittal and vertical skeletal facial growth pattern and maxillary posterior discrepancy (present or absent). Upper molar vertical position, overbite, lower anterior facial height and facial height ratio were measured. Independent t-test was performed to determine differences between the groups considering maxillary posterior discrepancy. Principal component analysis and MANCOVA test were also used. Results: No statistically significant differences were found comparing the molar vertical position according to maxillary posterior discrepancy for the SOB Class I group or the group with adequate overbite. Significant differences were found in SOB Class II and Class III groups. In addition, an increased molar vertical position was found in the group without posterior discrepancy. Limitations: Some variables closely related with the individual’s intrinsic craniofacial development that could influence the evaluated vertical measurements were not considered. Conclusions and implications: Overall maxillary posterior discrepancy does not appear to have a clear impact on upper molar vertical position or facial vertical dimensions. Only the SOB Class III group without posterior discrepancy had a significant increased upper molar vertical position. PMID:26385786

Lincoln's vertical strabismus.

PubMed

Goldstein, J H

1997-01-01

The vertical strabismus manifested by Abraham Lincoln has been noted. This article reviews the historical findings and provides a specific diagnosis. Previous reports of symptoms and history relating to Lincoln's left hypertropia were reviewed. A series of photographs were reviewed. Lincoln's own description of his symptoms is provided. Previous history indicates an intermittent left hypertropia. A family history of vertical strabismus was noted with regard to Mr Lincoln's cousin. There also is a history of trauma to the left frontal area and life-mask evidence of fracture over the left eye. The findings include a history of head tilt and diplopia, presumably most readily in downgaze. Given the history and findings, the diagnosis of left superior oblique paresis of either congenital or traumatic origin seems appropriate.

VERTICAL BEAM SIZE CONTROL IN TLS AND TPS.

DOE Office of Scientific and Technical Information (OSTI.GOV)

KUO, C.C.; CHEN, J.R.; CHOU, P.J.

2006-06-26

Vertical beam size control is an important issue in the light source operations. The horizontal-vertical betatron coupling and vertical dispersion were measured and corrected to small values in the TLS 1.5 GeV storage ring. Estimated beam sizes are compared with the measured values. By employing an effective transverse damping system, the vertical beam blow-up due to transverse coherent instabilities, such as the fast-ion beam instability, was suppressed. As a result, the light source is very stable. In NSRRC we are designing an ultra low emittance 3-GeV storage ring and its designed vertical beam size could be as small as amore » few microns. The ground and mechanic vibration effects, and coherent instabilities could spoil the expected photon brightness due to blow-up of the vertical beam size if not well taken care of. The contributions of these effects to vertical beam size increase will be evaluated and the counter measures to minimize them will be proposed and reported in this paper.« less

The Ames Vertical Gun Range

NASA Technical Reports Server (NTRS)

Karcz, J. S.; Bowling, D.; Cornelison, C.; Parrish, A.; Perez, A.; Raiche, G.; Wiens, J.-P.

2016-01-01

The Ames Vertical Gun Range (AVGR) is a national facility for conducting laboratory- scale investigations of high-speed impact processes. It provides a set of light-gas, powder, and compressed gas guns capable of accelerating projectiles to speeds up to 7 km s(exp -1). The AVGR has a unique capability to vary the angle between the projectile-launch and gravity vectors between 0 and 90 deg. The target resides in a large chamber (diameter approximately 2.5 m) that can be held at vacuum or filled with an experiment-specific atmosphere. The chamber provides a number of viewing ports and feed-throughs for data, power, and fluids. Impacts are observed via high-speed digital cameras along with investigation-specific instrumentation, such as spectrometers. Use of the range is available via grant proposals through any Planetary Science Research Program element of the NASA Research Opportunities in Space and Earth Sciences (ROSES) calls. Exploratory experiments (one to two days) are additionally possible in order to develop a new proposal.

Diel Vertical Migration Thresholds of Karenia brevis (Dinophyceae).

EPA Science Inventory

Light and nutrient availability change throughout dinoflagellate diel vertical migration (DVM) and/or with subpopulation location in the water column along the west Florida shelf. Typically, the vertical depth of the shelf is greater than the distance a subpopulation can vertical...

Methods of testing parameterizations: Vertical ocean mixing

NASA Technical Reports Server (NTRS)

Tziperman, Eli

1992-01-01

The ocean's velocity field is characterized by an exceptional variety of scales. While the small-scale oceanic turbulence responsible for the vertical mixing in the ocean is of scales a few centimeters and smaller, the oceanic general circulation is characterized by horizontal scales of thousands of kilometers. In oceanic general circulation models that are typically run today, the vertical structure of the ocean is represented by a few tens of discrete grid points. Such models cannot explicitly model the small-scale mixing processes, and must, therefore, find ways to parameterize them in terms of the larger-scale fields. Finding a parameterization that is both reliable and plausible to use in ocean models is not a simple task. Vertical mixing in the ocean is the combined result of many complex processes, and, in fact, mixing is one of the less known and less understood aspects of the oceanic circulation. In present models of the oceanic circulation, the many complex processes responsible for vertical mixing are often parameterized in an oversimplified manner. Yet, finding an adequate parameterization of vertical ocean mixing is crucial to the successful application of ocean models to climate studies. The results of general circulation models for quantities that are of particular interest to climate studies, such as the meridional heat flux carried by the ocean, are quite sensitive to the strength of the vertical mixing. We try to examine the difficulties in choosing an appropriate vertical mixing parameterization, and the methods that are available for validating different parameterizations by comparing model results to oceanographic data. First, some of the physical processes responsible for vertically mixing the ocean are briefly mentioned, and some possible approaches to the parameterization of these processes in oceanographic general circulation models are described in the following section. We then discuss the role of the vertical mixing in the physics of the

Influence of maxillary posterior discrepancy on upper molar vertical position and facial vertical dimensions in subjects with or without skeletal open bite.

PubMed

Arriola-Guillén, Luis Ernesto; Aliaga-Del Castillo, Aron; Pérez-Vargas, Luis Fernando; Flores-Mir, Carlos

2016-06-01

To determine the influence of maxillary posterior discrepancy on upper molar vertical position and dentofacial vertical dimensions in individuals with or without skeletal open bite (SOB). Pre-treatment lateral cephalograms of 139 young adults were examined. The sample was divided into eight groups categorized according to their sagittal and vertical skeletal facial growth pattern and maxillary posterior discrepancy (present or absent). Upper molar vertical position, overbite, lower anterior facial height and facial height ratio were measured. Independent t-test was performed to determine differences between the groups considering maxillary posterior discrepancy. Principal component analysis and MANCOVA test were also used. No statistically significant differences were found comparing the molar vertical position according to maxillary posterior discrepancy for the SOB Class I group or the group with adequate overbite. Significant differences were found in SOB Class II and Class III groups. In addition, an increased molar vertical position was found in the group without posterior discrepancy. Some variables closely related with the individual's intrinsic craniofacial development that could influence the evaluated vertical measurements were not considered. Overall maxillary posterior discrepancy does not appear to have a clear impact on upper molar vertical position or facial vertical dimensions. Only the SOB Class III group without posterior discrepancy had a significant increased upper molar vertical position. © The Author 2015. Published by Oxford University Press on behalf of the European Orthodontic Society. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Vertical profiles of BC direct radiative effect over Italy: high vertical resolution data and atmospheric feedbacks

NASA Astrophysics Data System (ADS)

Močnik, Griša; Ferrero, Luca; Castelli, Mariapina; Ferrini, Barbara S.; Moscatelli, Marco; Grazia Perrone, Maria; Sangiorgi, Giorgia; Rovelli, Grazia; D'Angelo, Luca; Moroni, Beatrice; Scardazza, Francesco; Bolzacchini, Ezio; Petitta, Marcello; Cappelletti, David

2016-04-01

Black carbon (BC), and its vertical distribution, affects the climate. Global measurements of BC vertical profiles are lacking to support climate change research. To fill this gap, a campaign was conducted over three Italian basin valleys, Terni Valley (Appennines), Po Valley and Passiria Valley (Alps), to characterize the impact of BC on the radiative budget under similar orographic conditions. 120 vertical profiles were measured in winter 2010. The BC vertical profiles, together with aerosol size distribution, aerosol chemistry and meteorological parameters, have been determined using a tethered balloon-based platform equipped with: a micro-Aethalometer AE51 (Magee Scientific), a 1.107 Grimm OPC (0.25-32 μm, 31 size classes), a cascade impactor (Siuotas SKC), and a meteorological station (LSI-Lastem). The aerosol chemical composition was determined from collected PM2.5 samples. The aerosol absorption along the vertical profiles was measured and optical properties calculated using the Mie theory applied to the aerosol size distribution. The aerosol optical properties were validated with AERONET data and then used as inputs to the radiative transfer model libRadtran. Vertical profiles of the aerosol direct radiative effect, the related atmospheric absorption and the heating rate were calculated. Vertical profile measurements revealed some common behaviors over the studied basin valleys. From below the mixing height to above it, a marked concentration drop was found for both BC (from -48.4±5.3% up to -69.1±5.5%) and aerosol number concentration (from -23.9±4.3% up to -46.5±7.3%). These features reflected on the optical properties of the aerosol. Absorption and scattering coefficients decreased from below the MH to above it (babs from -47.6±2.5% up to -71.3±3.0% and bsca from -23.5±0.8% up to -61.2±3.1%, respectively). Consequently, the Single Scattering Albedo increased above the MH (from +4.9±2.2% to +7.4±1.0%). The highest aerosol absorption was

Characterization of vertical mixing in oscillatory vegetated flows

NASA Astrophysics Data System (ADS)

Abdolahpour, M.; Ghisalberti, M.; Lavery, P.; McMahon, K.

2016-02-01

Seagrass meadows are primary producers that provide important ecosystem services, such as improved water quality, sediment stabilisation and trapping and recycling of nutrients. Most of these ecological services are strongly influenced by the vertical exchange of water across the canopy-water interface. That is, vertical mixing is the main hydrodynamic process governing the large-scale ecological and environmental impact of seagrass meadows. The majority of studies into mixing in vegetated flows have focused on steady flow environments whereas many coastal canopies are subjected to oscillatory flows driven by surface waves. It is known that the rate of mass transfer will vary greatly between unidirectional and oscillatory flows, necessitating a specific investigation of mixing in oscillatory canopy flows. In this study, we conducted an extensive laboratory investigation to characterise the rate of vertical mixing through a vertical turbulent diffusivity (Dt,z). This has been done through gauging the evolution of vertical profiles of concentration (C) of a dye sheet injected into a wave-canopy flow. Instantaneous measurement of the variance of the vertical concentration distribution ( allowed the estimation of a vertical turbulent diffusivity (). Two types of model canopies, rigid and flexible, with identical heights and frontal areas, were subjected to a wide and realistic range of wave height and period. The results showed two important mechanisms that dominate vertical mixing under different conditions: a shear layer that forms at the top of the canopy and wake turbulence generated by the stems. By allowing a coupled contribution of wake and shear layer mixing, we present a relationship that can be used to predict the rate of vertical mixing in coastal canopies. The results further showed that the rate of vertical mixing within flexible vegetation was always lower than the corresponding rigid canopy, confirming the impact of plant flexibility on canopy

Climatology of tropospheric vertical velocity spectra

NASA Technical Reports Server (NTRS)

Ecklund, W. L.; Gage, K. S.; Balsley, B. B.; Carter, D. A.

1986-01-01

Vertical velocity power spectra obtained from Poker Flat, Alaska; Platteville, Colorado; Rhone Delta, France; and Ponape, East Caroline Islands using 50-MHz clear-air radars with vertical beams are given. The spectra were obtained by analyzing the quietest periods from the one-minute-resolution time series for each site. The lengths of available vertical records ranged from as long as 6 months at Poker Flat to about 1 month at Platteville. The quiet-time vertical velocity spectra are shown. Spectral period ranging from 2 minutes to 4 hours is shown on the abscissa and power spectral density is given on the ordinate. The Brunt-Vaisala (B-V) periods (determined from nearby sounding balloons) are indicated. All spectra (except the one from Platteville) exhibit a peak at periods slightly longer than the B-V period, are flat at longer periods, and fall rapidly at periods less than the B-V period. This behavior is expected for a spectrum of internal waves and is very similar to what is observed in the ocean (Eriksen, 1978). The spectral amplitudes vary by only a factor of 2 or 3 about the mean, and show that under quiet conditions vertical velocity spectra from the troposphere are very similar at widely different locations.

Water Levels and Selected Water-Quality Conditions in the Sparta-Memphis Aquifer (Middle Claiborne Aquifer) in Arkansas, Spring-Summer 2007

USGS Publications Warehouse

Schrader, T.P.

2009-01-01

The U.S. Geological Survey in cooperation with the Arkansas Natural Resources Commission and the Arkansas Geological Survey has monitored water levels in the Sparta Sand of Claiborne Group and Memphis Sand of Claiborne Group (herein referred to as the Sparta Sand and the Memphis Sand, respectively), since the 1920s. Groundwater withdrawals have increased while water levels have declined since monitoring was initiated. Herein, aquifers in the Sparta Sand and Memphis Sand will be referred to as the Sparta-Memphis aquifer throughout Arkansas. During the spring of 2007, 309 water levels were measured in wells completed in the Sparta-Memphis aquifer. During the summer of 2007, 129 water-quality samples were collected and measured for temperature and specific conductance and 102 were collected and analyzed for chloride from wells completed in the Sparta-Memphis aquifer. Water-level measurements collected in wells screened in the Sparta-Memphis aquifer were used to produce a regional potentiometric-surface map. The regional direction of groundwater flow in the Sparta-Memphis aquifer is generally to the south-southeast in the northern half of Arkansas and to the east and south in the southern half of Arkansas, away from the outcrop area except where affected by large ground-water withdrawals. The highest water-level altitude measured in the Sparta-Memphis aquifer was 326 feet above National Geodetic Vertical Datum of 1929, located in Grant County in the outcrop at the western boundary of the study area; the lowest water-level altitude was 161 feet below National Geodetic Vertical Datum of 1929 in Union County near the southern boundary of the study area. Eight cones of depression (generally represented by closed contours) are located in the following counties: Bradley, Drew, and Ashley; Calhoun; Cleveland; Columbia; Crittenden; Arkansas, Jefferson, and Lincoln; Cross and Poinsett; and Union. Two large depressions are shown on the 2007 potentiometric-surface map, centered

French vertical-flow constructed wetland design: adaptations for tropical climates.

PubMed

Molle, P; Latune, R Lombard; Riegel, C; Lacombe, G; Esser, D; Mangeot, L

2015-01-01

The French Outermost Regions are under tropical climate yet still have to comply with both French and EU regulations. French vertical-flow constructed wetland systems appear well adapted to the technical specifics of these regions but their adaptation to tropical climate requires new design guidelines to be defined (area needed, number of filters, type of plants, material to be used, etc.). A study was started in 2008, with backing from the national water authorities, to implement full-scale experimental sites and assess the impacts of local context on design and performances. This paper reports the monitoring results on three vertical-flow constructed wetlands fed directly with raw wastewater (known as the 'French system') in Mayotte and French Guiana. The plants, now in operation for between 1 and 6 years, range from 160 to 480 population equivalent (p.e.). Monitoring consisted of 28 daily composite flow samples in different seasons (dry season, rainy season) at the inlet and outlet of each filter. Performances are benchmarked against French mainland area standards from Irstea's database. Results show that performances are improved by warmer temperature for chemical oxygen demand (COD), suspended solids (SS) and total Kjeldahl nitrogen (TKN) and satisfy national quality objectives with a single stage of filters. Treatment plant footprint can thus be reduced as only two parallel filters are needed. Indeed, warm temperatures allow faster mineralization of the sludge deposit, making it possible to operate at similar rest and feeding period durations. Systems operated using one twin-filter stage can achieve over 90% COD, SS and TKN removal for a total surface of 0.8 m²/p.e.

2002 Airborne Geophysical Survey at Pueblo of Isleta Bombing Targets, New Mexico, April 10 May 6, 2002 (Rev 1)

DTIC Science & Technology

2005-12-01

helicopter geophysical survey performed by US Army Engineering Support Center, Huntsville (USAESCH) and Oak Ridge National Laboratory ( ORNL ) over areas...Array Detection System NAD North American Datum ORAGS Oak Ridge Airborne Geophysical System ORNL Oak Ridge National Laboratory RMS Root...used by ORNL in 1999 for.....................5 Figure 2.4 ORAGS-Hammerhead airborne magnetometer system used at Badlands Bombing Range in FY2000

Verticality perception during and after galvanic vestibular stimulation.

PubMed

Volkening, Katharina; Bergmann, Jeannine; Keller, Ingo; Wuehr, Max; Müller, Friedemann; Jahn, Klaus

2014-10-03

The human brain constructs verticality perception by integrating vestibular, somatosensory, and visual information. Here we investigated whether galvanic vestibular stimulation (GVS) has an effect on verticality perception both during and after application, by assessing the subjective verticals (visual, haptic and postural) in healthy subjects at those times. During stimulation the subjective visual vertical and the subjective haptic vertical shifted towards the anode, whereas this shift was reversed towards the cathode in all modalities once stimulation was turned off. Overall, the effects were strongest for the haptic modality. Additional investigation of the time course of GVS-induced changes in the haptic vertical revealed that anodal shifts persisted for the entire 20-min stimulation interval in the majority of subjects. Aftereffects exhibited different types of decay, with a preponderance for an exponential decay. The existence of such reverse effects after stimulation could have implications for GVS-based therapy. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

33 CFR 118.85 - Lights on vertical lift bridges.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 1 2011-07-01 2011-07-01 false Lights on vertical lift bridges... BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.85 Lights on vertical lift bridges. (a) Lift span lights. The vertical lift span of every vertical lift bridge shall be lighted so that the center of the...

33 CFR 118.85 - Lights on vertical lift bridges.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Lights on vertical lift bridges... BRIDGES BRIDGE LIGHTING AND OTHER SIGNALS § 118.85 Lights on vertical lift bridges. (a) Lift span lights. The vertical lift span of every vertical lift bridge shall be lighted so that the center of the...

JPSS-1 Delta II Interstage Hoisted from Horizontal and Rotated to Vertical for Transport

NASA Image and Video Library

2016-07-06

The interstage section of the United Launch Alliance Delta II rocket that will launch the Joint Polar Satellite System-1 (JPSS-1) is hoisted to vertical in Building 836 on Vandenberg Air Force Base in California. JPSS, a next-generation environmental satellite system, is a collaborative program between the National Oceanic and Atmospheric Administration (NOAA) and NASA. Launch is targeted for March 27, 2017. To learn more about JPSS-1, visit www.jpss.noaa.gov.

Orienting numbers in mental space: horizontal organization trumps vertical.

PubMed

Holmes, Kevin J; Lourenco, Stella F

2012-01-01

While research on the spatial representation of number has provided substantial evidence for a horizontally oriented mental number line, recent studies suggest vertical organization as well. Directly comparing the relative strength of horizontal and vertical organization, however, we found no evidence of spontaneous vertical orientation (upward or downward), and horizontal trumped vertical when pitted against each other (Experiment 1). Only when numbers were conceptualized as magnitudes (as opposed to nonmagnitude ordinal sequences) did reliable vertical organization emerge, with upward orientation preferred (Experiment 2). Altogether, these findings suggest that horizontal representations predominate, and that vertical representations, when elicited, may be relatively inflexible. Implications for spatial organization beyond number, and its ontogenetic basis, are discussed.

The psychophysical periphery effect crosses the vertical meridian.

PubMed

Kuyk, T; Niculescu, D

2001-01-01

This study measured the periphery effect and compared its magnitude when the peripheral stimulation was on the same or opposite side of the vertical meridian as the test spot. Test thresholds for a 1.5-deg diameter, 8-ms spot located 1.75 deg to one side of the vertical meridian were elevated by approximately 0.125 log units when a 0.25 cycles/deg (cpd) counterphased grating was presented at a similar eccentric offset on the other side of the vertical meridian. The periphery effect disappeared when the test spot was moved outward to 8-deg eccentricity. When the grating and test were presented on the same side of the vertical meridian, test thresholds at both retinal locations were elevated by the same amount, 0.2 log units. Consistent with the physiology in cat retina, the periphery effect in humans also crosses over the vertical meridian. However, the effect is small and the test spot must be in close proximity to the vertical meridian for it to be observed. Also, the crossover periphery effect is reduced in magnitude by 37.5% compared to when the grating and test are presented on the same side of the vertical meridian. This suggests there may be a difference in how the underlying neural mechanism that transmits the periphery effect signal laterally is organized for sending the periphery effect signal across the vertical meridian as compared to within a retinal hemifield.

Controlling Guessing Bias in the Dichotomous Rasch Model Applied to a Large-Scale, Vertically Scaled Testing Program

ERIC Educational Resources Information Center

Andrich, David; Marais, Ida; Humphry, Stephen Mark

2016-01-01

Recent research has shown how the statistical bias in Rasch model difficulty estimates induced by guessing in multiple-choice items can be eliminated. Using vertical scaling of a high-profile national reading test, it is shown that the dominant effect of removing such bias is a nonlinear change in the unit of scale across the continuum. The…

Plasmonic Properties of Vertically Aligned Nanowire Arrays

DTIC Science & Technology

2012-01-01

scattering (SERS) applications. In this investigation, two types of vertical NW arrays were studied; those of ZnO NWs grown on nanosphere lithography...plasmonic nanowires to investigate this SERS effect. Here we used two types of vertical NWs, ZnO NWs, and Si NWs, respectively, to investigate SERS...successfully grow vertically aligned ZnO nanowires by the well-known VLS process. In this way, the ZnO NWs can be arranged in a repeatable hexagonal pattern

Bathymetric surveys of the Neosho River, Spring River, and Elk River, northeastern Oklahoma and southwestern Missouri, 2016–17

USGS Publications Warehouse

Hunter, Shelby L.; Ashworth, Chad E.; Smith, S. Jerrod

2017-09-26

River was 709.18 ft above North American Vertical Datum of 1988, which corresponds to a maximum depth of 34.22 ft. The minimum bathymetric-survey elevation of the Spring River was 714.18 ft above North American Vertical Datum of 1988, which corresponds to a maximum depth of 29.22 ft. The minimum bathymetric-survey elevation of the Elk River was 715.62 ft above North American Vertical Datum of 1988, which corresponds to a maximum depth of 27.78 ft.

Vertical Flume Testing of WIPP Surrogate Waste Materials

NASA Astrophysics Data System (ADS)

Herrick, C. G.; Schuhen, M.; Kicker, D.

2012-12-01

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy geological repository for the permanent disposal of defense-related transuranic (TRU) waste. The waste is emplaced in rooms excavated in the bedded Salado salt formation at a depth of 655 m below ground surface. After emplacement of the waste, the repository will be sealed and decommissioned. The DOE demonstrates compliance with 40 CFR 194 by means of performance assessment (PA) calculations conducted by Sandia National Laboratories. WIPP PA calculations estimate the probability and consequences of radionuclide releases for a 10,000 year regulatory period. Human intrusion scenarios include cases in which a future borehole is drilled through the repository. Drilling mud flowing up the borehole will apply a hydrodynamic shear stress to the borehole wall which could result in erosion of the waste and radionuclides being carried up the borehole. WIPP PA uses the parameter TAUFAIL to represent the shear strength of the degraded waste. The hydrodynamic shear strength can only be measured experimentally by flume testing. Flume testing is typically performed horizontally, mimicking stream or ocean currents. However, in a WIPP intrusion event, the drill bit would penetrate the degraded waste and drilling mud would flow up the borehole in a predominantly vertical direction. In order to simulate this, a flume was designed and built so that the eroding fluid enters an enclosed vertical channel from the bottom and flows up past a specimen of surrogate waste material. The sample is pushed into the current by a piston attached to a step motor. A qualified data acquisition system controls and monitors the fluid's flow rate, temperature, pressure, and conductivity and the step motor's operation. The surrogate materials used correspond to a conservative estimate of degraded TRU waste at the end of the regulatory period. The recipes were previously developed by SNL based on anticipated future states of the waste

Vertical Flume Testing of WIPP Surrogate Waste Materials

NASA Astrophysics Data System (ADS)

Herrick, C. G.; Schuhen, M.; Kicker, D.

2013-12-01

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy geological repository for the permanent disposal of defense-related transuranic (TRU) waste. The waste is emplaced in rooms excavated in the bedded Salado salt formation at a depth of 655 m below ground surface. After emplacement of the waste, the repository will be sealed and decommissioned. The DOE demonstrates compliance with 40 CFR 194 by means of performance assessment (PA) calculations conducted by Sandia National Laboratories. WIPP PA calculations estimate the probability and consequences of radionuclide releases for a 10,000 year regulatory period. Human intrusion scenarios include cases in which a future borehole is drilled through the repository. Drilling mud flowing up the borehole will apply a hydrodynamic shear stress to the borehole wall which could result in erosion of the waste and radionuclides being carried up the borehole. WIPP PA uses the parameter TAUFAIL to represent the shear strength of the degraded waste. The hydrodynamic shear strength can only be measured experimentally by flume testing. Flume testing is typically performed horizontally, mimicking stream or ocean currents. However, in a WIPP intrusion event, the drill bit would penetrate the degraded waste and drilling mud would flow up the borehole in a predominantly vertical direction. In order to simulate this, a flume was designed and built so that the eroding fluid enters an enclosed vertical channel from the bottom and flows up past a specimen of surrogate waste material. The sample is pushed into the current by a piston attached to a step motor. A qualified data acquisition system controls and monitors the fluid's flow rate, temperature, pressure, and conductivity and the step motor's operation. The surrogate materials used correspond to a conservative estimate of degraded TRU waste at the end of the regulatory period. The recipes were previously developed by SNL based on anticipated future states of the waste

Rotor instrumentation circuits for the Sandia 34-meter vertical axis wind turbine

NASA Astrophysics Data System (ADS)

Sutherland, Herbert J.; Stephenson, William A.

1988-07-01

Sandia National Laboratories has erected a research oriented, 34-meter diameter, Darrieus vertical axis wind turbine near Bushland, Texas, which has been designated the Sandia 34-m VAWT Test Bed. To meet present and future research needs, the machine was equipped with a large array of sensors. This manuscript details the sensors initially placed on the rotor, their respective instrumentation circuits, and the provisions incorporated into the design of the rotor instrumentation circuits for future research. This manuscript was written as a reference manual for the rotor instrumentation of the Test Bed.

Evaluation of NSF's Program of Grants and Vertical Integration of Research and Education in the Mathematical Sciences (VIGRE)

ERIC Educational Resources Information Center

National Academies Press, 2009

2009-01-01

In 1998, the National Science Foundation (NSF) launched a program of Grants for Vertical Integration of Research and Education in the Mathematical Sciences (VIGRE). These grants were designed for institutions with PhD-granting departments in the mathematical sciences, for the purpose of developing high-quality education programs, at all levels,…

Velocity, water-quality, and bathymetric surveys of the Grays Landing and Maxwell Navigation Pools, and Selected Tributaries to the Monongahela River, Pennsylvania, 2010–11

USGS Publications Warehouse

Hoffman, Scott A.; Roland, Mark A.; Schalk, Luther F.; Fulton, John W.

2013-01-01

The U.S. Geological Survey (USGS) conducted velocity, water-quality, and bathymetric surveys from spring 2010 to summer 2011 in the Grays Landing and Maxwell navigation pools of the Monongahela River, Pennsylvania, and selected tributaries in response to elevated levels of total dissolved solids (TDS) recorded in early September 2009. Velocity data were collected using an Acoustic Doppler Current Profiler. Water-quality surveys included the in-situ collection of specific-conductance, water-temperature, and turbidity data using a water-quality sonde. Additionally, discrete water samples were collected and analyzed for TDS, chloride, and sulfate. Bathymetric data were collected using an echo sounder, and the shoreline was delineated using a laser range finder and electronic compass. The data were geo-referenced using a differential global positioning system and navigational software. Horizontal (x, y) coordinates were referenced to the North American Datum of 1983. Depth (z) elevations were referenced to the North American Vertical Datum of 1988. The data are provided in electronic format (appendix 1) and may be downloaded and can be used in a geographic information system for cartographic display and data analysis.

GNSS Positioning by CORS and EGM2008 in Jilin Province, China

PubMed Central

Wu, Qiong; Kang, Jingyu; Li, Shuwen; Zhen, Jianing; Li, Hongqing

2015-01-01

The Continuously Operating Reference Station (CORS) technique has been widely applied in land resource management, surveying, mapping, deformation monitoring, precise navigation, etc. This article analyzed the positioning method using EGM2008 and CORS of Jilin Province, China. The vertical transformation of EGM2008 from WGS84 to China’s CGCS2000 datum and the horizontal coordinate transformation from CGCS2000 to a triangulation coordinate system were discussed. The results indicated that a local geoid with respect to CGCS2000 can be transferred from EGM2008 with the same accuracy, and the geoid correction between CGCS2000 and WGS84 varied from 0.023 m to 0.111 m. The coordinate transformation method based on the curve surface approximation method indicated that the theoretical error was less than 0.09 m in the grid within 10° longitudinal and 5° latitudinal, and less than 0.3 m in large area and 0.1 m in small area in field validation. The method proposed in this article expanded the positioning result and its application for JLCORS and other CORS with local datum. PMID:26690150

GNSS Positioning by CORS and EGM2008 in Jilin Province, China.

PubMed

Wu, Qiong; Kang, Jingyu; Li, Shuwen; Zhen, Jianing; Li, Hongqing

2015-12-04

The Continuously Operating Reference Station (CORS) technique has been widely applied in land resource management, surveying, mapping, deformation monitoring, precise navigation, etc. This article analyzed the positioning method using EGM2008 and CORS of Jilin Province, China. The vertical transformation of EGM2008 from WGS84 to China's CGCS2000 datum and the horizontal coordinate transformation from CGCS2000 to a triangulation coordinate system were discussed. The results indicated that a local geoid with respect to CGCS2000 can be transferred from EGM2008 with the same accuracy, and the geoid correction between CGCS2000 and WGS84 varied from 0.023 m to 0.111 m. The coordinate transformation method based on the curve surface approximation method indicated that the theoretical error was less than 0.09 m in the grid within 10° longitudinal and 5° latitudinal, and less than 0.3 m in large area and 0.1 m in small area in field validation. The method proposed in this article expanded the positioning result and its application for JLCORS and other CORS with local datum.

[Duane vertical surgical treatment].

PubMed

Merino, M L; Gómez de Liaño, P; Merino, P; Franco, G

2014-04-01

We report 3 cases with a vertical incomitance in upgaze, narrowing of palpebral fissure, and pseudo-overaction of both inferior oblique muscles. Surgery consisted of an elevation of both lateral rectus muscles with an asymmetrical weakening. A satisfactory result was achieved in 2 cases, whereas a Lambda syndrome appeared in the other case. The surgical technique of upper-insertion with a recession of both lateral rectus muscles improved vertical incomitance in 2 of the 3 patients; however, a residual deviation remains in the majority of cases. Copyright © 2011 Sociedad Española de Oftalmología. Published by Elsevier Espana. All rights reserved.

Lightning Nitrogen Oxides (LNOx) Vertical Profile Quantification and 10 Year Trend Analysis using Ozone Monitoring Instrument (OMI) Satellite Measurements, Air Quality Station (AQS) Surface Measurements, The National Lightning Detection Network (NLDN), and Simulated by Cloud Resolving Chemical Transport Model (REAM Cloud)

NASA Astrophysics Data System (ADS)

Smeltzer, C. D.; Wang, Y.; Koshak, W. J.

2014-12-01

Vertical profiles and emission lifetimes of lightning nitrogen oxides (LNOx) are derived using the Ozone Monitoring Instrument (OMI). Approximately 200 million flashes, over a 10 year climate period, from the United States National Lighting Detection Network (NLDN), are aggregated with OMI cloud top height to determine the vertical LNOx structure. LNOx lifetime is determined as function of LNOx signal in a 36 kilometer vertical column from the time of the last known flash to depletion of the LNOx signal. Environmental Protection Agency (EPA) Air Quality Station (AQS) surface data further support these results by demonstrating as much as a 200% increase in surface level NO2 during strong thunderstorm events and a lag as long as 5 to 8 hours from the lightning event to the peak surface event, indicating a evolutional process. Analysis of cloud resolving chemical transport model (REAM Cloud) demonstrates that C-shaped LNOx profiles, which agree with OMI vertical profile observations, evolve due to micro-scale convective meteorology given inverted C-shaped LNOx emission profiles as determined from lightning radio telemetry. It is shown, both in simulations and in observations, that the extent to which the LNOx vertical distribution is C-shaped and the lifetime of LNOx is proportional to the shear-strength of the thunderstorm. Micro-scale convective meteorology is not adequately parameterized in global scale and regional scale chemical transport models (CTM). Therefore, these larger scale CTMs ought to use a C-shape emissions profile to best reproduce observations until convective parameterizations are updated. These findings are used to simulate decadal LNOx and lightning ozone climatology over the Continental United States (CONUS) from 2004-2014.

[Vertical fractures: apropos of 2 clinical cases].

PubMed

Félix Mañes Ferrer, J; Micò Muñoz, P; Sánchez Cortés, J L; Paricio Martín, J J; Miñana Laliga, R

1991-01-01

The aim of the study is to present a clinical review of the vertical root fractures. Two clinical cases are presented to demonstrates the criteria for obtaining a correct diagnosis of vertical root fractures.

Vertical resolution of baroclinic modes in global ocean models

NASA Astrophysics Data System (ADS)

Stewart, K. D.; Hogg, A. McC.; Griffies, S. M.; Heerdegen, A. P.; Ward, M. L.; Spence, P.; England, M. H.

2017-05-01

Improvements in the horizontal resolution of global ocean models, motivated by the horizontal resolution requirements for specific flow features, has advanced modelling capabilities into the dynamical regime dominated by mesoscale variability. In contrast, the choice of the vertical grid remains a subjective choice, and it is not clear that efforts to improve vertical resolution adequately support their horizontal counterparts. Indeed, considering that the bulk of the vertical ocean dynamics (including convection) are parameterized, it is not immediately obvious what the vertical grid is supposed to resolve. Here, we propose that the primary purpose of the vertical grid in a hydrostatic ocean model is to resolve the vertical structure of horizontal flows, rather than to resolve vertical motion. With this principle we construct vertical grids based on their abilities to represent baroclinic modal structures commensurate with the theoretical capabilities of a given horizontal grid. This approach is designed to ensure that the vertical grids of global ocean models complement (and, importantly, to not undermine) the resolution capabilities of the horizontal grid. We find that for z-coordinate global ocean models, at least 50 well-positioned vertical levels are required to resolve the first baroclinic mode, with an additional 25 levels per subsequent mode. High-resolution ocean-sea ice simulations are used to illustrate some of the dynamical enhancements gained by improving the vertical resolution of a 1/10° global ocean model. These enhancements include substantial increases in the sea surface height variance (∼30% increase south of 40°S), the barotropic and baroclinic eddy kinetic energies (up to 200% increase on and surrounding the Antarctic continental shelf and slopes), and the overturning streamfunction in potential density space (near-tripling of the Antarctic Bottom Water cell at 65°S).

Vertical root fractures and their management

PubMed Central

Khasnis, Sandhya Anand; Kidiyoor, Krishnamurthy Haridas; Patil, Anand Basavaraj; Kenganal, Smita Basavaraj

2014-01-01

Vertical root fractures associated with endodontically treated teeth and less commonly in vital teeth represent one of the most difficult clinical problems to diagnose and treat. In as much as there are no specific symptoms, diagnosis can be difficult. Clinical detection of this condition by endodontists is becoming more frequent, where as it is rather underestimated by the general practitioners. Since, vertical root fractures almost exclusively involve endodontically treated teeth; it often becomes difficult to differentiate a tooth with this condition from an endodontically failed one or one with concomitant periodontal involvement. Also, a tooth diagnosed for vertical root fracture is usually extracted, though attempts to reunite fractured root have been done in various studies with varying success rates. Early detection of a fractured root and extraction of the tooth maintain the integrity of alveolar bone for placement of an implant. Cone beam computed tomography has been shown to be very accurate in this regard. This article focuses on the diagnostic and treatment strategies, and discusses about predisposing factors which can be useful in the prevention of vertical root fractures. PMID:24778502

Vertical Feature Mask Feature Classification Flag Extraction

Atmospheric Science Data Center

2013-03-28

  Vertical Feature Mask Feature Classification Flag Extraction This routine demonstrates extraction of the ... in a CALIPSO Lidar Level 2 Vertical Feature Mask feature classification flag value. It is written in Interactive Data Language (IDL) ...

Comparing models of seasonal deformation to horizontal and vertical PBO GPS data

NASA Astrophysics Data System (ADS)

Bartlow, N. M.; Fialko, Y. A.; van Dam, T. M.

2015-12-01

GPS monuments around the world exhibit seasonal displacements in both the horizontal and vertical direction with amplitudes on the order of centimeters. For analysis of tectonic signals, researchers typically fit and remove a sine function with an annual period, and sometimes an additional sine function with a semiannual period. As interest grows in analyzing small-amplitude, long-period deformation signals it becomes more important to accurately correct for seasonal variations. It is well established that the vertical component of seasonal GPS signals is largely due to continental water storage cycles (e.g. van Dam et al., GRL, 2001). Other recognized sources of seasonal loading include atmospheric pressure loading and oceanic loading due to non-steric changes in ocean height (e.g. van Dam et al., J. Geodesy, 2012). Here we attempt to build a complete physical model of seasonal loading by considering all of these sources (continental water storage, atmospheric pressure, and oceanic loading) and comparing our model to horizontal and vertical GPS data in the Western US. Atmospheric loading effects are computed from the National Center for Environmental Prediction 6-hourly global reanalysis surface pressure fields; the terrestrial water loading and ocean loading models are generated using SPOTL (Some Programs for Ocean Tide Loading; Agnew, SIO Technical Report, 2012) and parameters from NASA's Land Data Assimilation Systems and the Estimating the Circulation and Climate of the Ocean model, version 4. We find that with a few exceptions, our seasonal loading model predicts the correct phases but underestimates the amplitudes of vertical seasonal loads, and is a generally poor fit to the observed horizontal seasonal signals. This implies that our understanding of the driving mechanisms behind seasonal variations in the GPS data is still incomplete and needs to be improved before physics-based models can be used as an effective correction tool for the GPS timeseries.

Influence of short incompatible practice on the Simon effect: transfer along the vertical dimension and across vertical and horizontal dimensions.

PubMed

Conde, Erick F Q; Fraga-Filho, Roberto Sena; Lameira, Allan Pablo; Mograbi, Daniel C; Riggio, Lucia; Gawryszewski, Luiz G

2015-11-01

In spatial compatibility and Simon tasks, the response is faster when stimulus and response locations are on the same side than when they are on opposite sides. It has been shown that a spatial incompatible practice leads to a subsequent modulation of the Simon effect along the horizontal dimension. It has also been reported that this modulation occurs both along and across vertical and horizontal dimensions, but only after intensive incompatible training (600 trials). In this work, we show that this modulatory effect can be obtained with a smaller number of incompatible trials, changing the spatial arrangement of the vertical response keys to obtain a stronger dimensional overlap between the spatial codes of stimuli and response keys. The results of Experiment 1 showed that 80 incompatible vertical trials abolished the Simon effect in the same dimension. Experiment 2 showed that a modulation of the vertical Simon effect could be obtained after 80 horizontal incompatible trials. Experiment 3 explored whether the transfer effect can also occur in a horizontal Simon task after a brief vertical spatial incompatibility task, and results were similar to the previous experiments. In conclusion, we suggest that the spatial arrangement between response key and stimulus locations may be critical to establish the short-term memory links that enable the transfer of learning between brief incompatible practices and the Simon effects, both along the vertical dimension and across vertical and horizontal dimensions.

UAS Well Clear Recovery Against Non-Cooperative Intruders Using Vertical Maneuvers

NASA Technical Reports Server (NTRS)

Cone, Andrew C.; Thipphavong, David; Lee, Seung Man; Santiago, Confesor

2017-01-01

This paper documents a study that drove the development of a mathematical expression in the detect-and-avoid (DAA) minimum operational performance standards (MOPS) for unmanned aircraft systems (UAS). This equation describes the conditions under which vertical maneuver guidance should be provided during recovery of DAA well clear separation with a non-cooperative VFR aircraft. Although the original hypothesis was that vertical maneuvers for DAA well clear recovery should only be offered when sensor vertical rate errors are small, this paper suggests that UAS climb and descent performance should be considered-in addition to sensor errors for vertical position and vertical rate-when determining whether to offer vertical guidance. A fast-time simulation study involving 108,000 encounters between a UAS and a non-cooperative visual-flight-rules aircraft was conducted. Results are presented showing that, when vertical maneuver guidance for DAA well clear recovery was suppressed, the minimum vertical separation increased by roughly 50 feet (or horizontal separation by 500 to 800 feet). However, the percentage of encounters that had a risk of collision when performing vertical well clear recovery maneuvers was reduced as UAS vertical rate performance increased and sensor vertical rate errors decreased. A class of encounter is identified for which vertical-rate error had a large effect on the efficacy of horizontal maneuvers due to the difficulty of making the correct left/right turn decision: crossing conflict with intruder changing altitude. Overall, these results support logic that would allow vertical maneuvers when UAS vertical performance is sufficient to avoid the intruder, based on the intruder's estimated vertical position and vertical rate, as well as the vertical rate error of the UAS' sensor.

A Vertically Resolved Planetary Boundary Layer

NASA Technical Reports Server (NTRS)

Helfand, H. M.

1984-01-01

Increase of the vertical resolution of the GLAS Fourth Order General Circulation Model (GCM) near the Earth's surface and installation of a new package of parameterization schemes for subgrid-scale physical processes were sought so that the GLAS Model GCM will predict the resolved vertical structure of the planetary boundary layer (PBL) for all grid points.

Driven acoustic oscillations within a vertical magnetic field

NASA Technical Reports Server (NTRS)

Hindman, Bradley W.; Zweibel, Ellen G.; Cally, P. S.

1995-01-01

The effects of a vertical magnetic field on p-mode frequencies, line widths, and eigenfunctions, are examined. A solar model, consisting of a neutrally stable polytropic interior matched to an isothermal chromosphere, is applied. The p-modes are produced by a spatially distributed driver. The atmosphere is threaded by a constant vertical magnetic field. The frequency shifts due to the vertical magnetic field are found to be much smaller than the shifts caused by horizontal fields of similar strength. A large vertical field of 2000 G produces shifts of several nHz. It is found that the frequency shifts decrease with increasing frequency and increase with field strength. The coupling of the acoustic fast mode to the escaping slow modes is inefficient. Constant vertical magnetic field models are therefore incapable of explaining the high level of absorption observed in sunspots and plage.

Surface tension profiles in vertical soap films

NASA Astrophysics Data System (ADS)

Adami, N.; Caps, H.

2015-01-01

Surface tension profiles in vertical soap films are experimentally investigated. Measurements are performed by introducing deformable elastic objets in the films. The shape adopted by those objects once set in the film is related to the surface tension value at a given vertical position by numerically solving the adapted elasticity equations. We show that the observed dependency of the surface tension versus the vertical position is predicted by simple modeling that takes into account the mechanical equilibrium of the films coupled to previous thickness measurements.

An Analysis of Strain Accumulation in the Western Part of Black Sea Region in Turkey

NASA Astrophysics Data System (ADS)

Deniz, I.; Avsar, N. B.; Deniz, R.; Mekik, C.; Kutoglu, S.

2014-12-01

Turkish National Horizontal Control Network (TNHCN) based on the European Datum 1950 (ED50) was used as the principal geodetic network until 2005 in Turkey. Since 2005, Turkish Large Scale Map and Map Information Production Regulation have required that that all the densification points have been produced within the same datum of Turkish National Fundamental GPS Network (TNFGN) put into practise in 2002 and based on International Terrestrial Reference Frame (ITRF). Hence, the common points were produced in both European Datum 1950 (ED50), and TNFGN.It is known that the geological and geophysical information about the network area can be obtained by the evaluation of the coordinate and scale variations in a geodetic network. For one such evaluation, the coordinate variations and velocities of network points, and also the strains are investigated. However, the principal problem in derivation of velocities arises from two different datums. In this context, the computation of velocities using the coordinate data of the ED50 and TNFGN is not accurate and reliable. Likewise, the analysis of strain from the coordinate differences is not reliable. However, due to the fact that the scale of a geodetic network is independent from datum, the strains can be derived from scale variations accurately and reliably.In this study, a test area limited 39.5°-42.0° northern latitudes and 31.0°-37.0° eastern longitudes was chosen. The benchmarks in this test area are composed of 30 geodetic control points derived with the aim of cadastral and engineering applications. We used data mining to investigate the common benchmarks in both reference systems for this area. Accordingly, the ED50 and TNFGN coordinates refer 1954 and 2005, respectively. Thus, it has been investigated the strain accumulation of 51 years in this region. It should be also noted that since 1954, the earthquakes have not registered greater than magnitude 6.0 in the test area. It is a considerable situation for this

Vertical high-precision Michelson wavemeter

NASA Astrophysics Data System (ADS)

Morales, A.; de Urquijo, J.; Mendoza, A.

1993-01-01

We have designed and tested a traveling, Michelson-type vertical wavemeter for the wavelength measurement of tunable continuous-wave lasers in the visible part of the spectrum. The interferometer has two movable corner cubes, suspending vertically from a driving setup resembling Atwood's machine. To reduce the fraction-of-fringe error, a vernier-type coincidence circuit was used. Although simple, this wavemeter has a relative precision of 3.2 parts in 109 for an overall fringe count of about 7×106.

Vertical melting of a stack of membranes

NASA Astrophysics Data System (ADS)

Borelli, M. E. S.; Kleinert, H.; Schakel, A. M. J.

2001-02-01

A stack of tensionless membranes with nonlinear curvature energy and vertical harmonic interaction is studied. At low temperatures, the system forms a lamellar phase. At a critical temperature, the stack disorders vertically in a melting-like transition.

Vertical velocity variance in the mixed layer from radar wind profilers

USGS Publications Warehouse

Eng, K.; Coulter, R.L.; Brutsaert, W.

2003-01-01

Vertical velocity variance data were derived from remotely sensed mixed layer turbulence measurements at the Atmospheric Boundary Layer Experiments (ABLE) facility in Butler County, Kansas. These measurements and associated data were provided by a collection of instruments that included two 915 MHz wind profilers, two radio acoustic sounding systems, and two eddy correlation devices. The data from these devices were available through the Atmospheric Boundary Layer Experiment (ABLE) database operated by Argonne National Laboratory. A signal processing procedure outlined by Angevine et al. was adapted and further built upon to derive vertical velocity variance, w_pm???2, from 915 MHz wind profiler measurements in the mixed layer. The proposed procedure consisted of the application of a height-dependent signal-to-noise ratio (SNR) filter, removal of outliers plus and minus two standard deviations about the mean on the spectral width squared, and removal of the effects of beam broadening and vertical shearing of horizontal winds. The scatter associated with w_pm???2 was mainly affected by the choice of SNR filter cutoff values. Several different sets of cutoff values were considered, and the optimal one was selected which reduced the overall scatter on w_pm???2 and yet retained a sufficient number of data points to average. A similarity relationship of w_pm???2 versus height was established for the mixed layer on the basis of the available data. A strong link between the SNR and growth/decay phases of turbulence was identified. Thus, the mid to late afternoon hours, when strong surface heating occurred, were observed to produce the highest quality signals.

Effect of Pitch Tilt on Vertical Optokinetic Nystagmus,

DTIC Science & Technology

1996-09-23

Naval Aerospace Medical Research Laboratory NAMRL-1394 EFFECT OF PITCH TILT ON VERTICAL OPTOKINETIC NYSTAGMUS M. J. Correia, O. I. Kolev, A...MEDICAL RESEARCH LABORATORY 51 HOVEY ROAD, PENSACOLA, FL 32508-1046 NAMRL-1394 EFFECT OF PITCH TILT ON VERTICAL OPTOKINETIC NYSTAGMUS M. J...Florida Pensacola, Florida Approved for public release; distribution unlimited. ABSTRACT Vertical optokinetic nystagmus (VOKN) and VOKN after

Reducing vertices in property graphs

PubMed Central

Pąk, Karol

2018-01-01

Graph databases are constantly growing, and, at the same time, some of their data is the same or similar. Our experience with the management of the existing databases, especially the bigger ones, shows that certain vertices are particularly replicated there numerous times. Eliminating repetitive or even very similar data speeds up the access to database resources. We present a modification of this approach, where similarly we group together vertices of identical properties, but then additionally we join together groups of data that are located in distant parts of a graph. The second part of our approach is non-trivial. We show that the search for a partition of a given graph where each member of the partition has only pairwise distant vertices is NP-hard. We indicate a group of heuristics that try to solve our difficult computational problems and then we apply them to check the the effectiveness of our approach. PMID:29444127

Proceedings of the vertical axis wind turbine (VAWT) design technology seminar for industry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnston, S.F. Jr.

1980-08-01

The objective of the Vertical Axis Wind Turbine (VAWT) Program at Sandia National Laboratories is to develop technology that results in economical, industry-produced, and commercially marketable wind energy systems. The purpose of the VAWT Design Technology Seminar or Industry was to provide for the exchange of the current state-of-the-art and predictions for future VAWT technology. Emphasis was placed on technology transfer on Sandia's technical developments and on defining the available analytic and design tools. Separate abstracts are included for presented papers.

The surface elevation table and marker horizon technique: A protocol for monitoring wetland elevation dynamics

USGS Publications Warehouse

James C. Lynch,; Phillippe Hensel,; Cahoon, Donald R.

2015-01-01

The National Park Service, in response to the growing evidence and awareness of the effects of climate change on federal lands, determined that monitoring wetland elevation change is a top priority in North Atlantic Coastal parks (Stevens et al, 2010). As a result, the NPS Northeast Coastal and Barrier Network (NCBN) in collaboration with colleagues from the U.S. Geological Survey (USGS) and The National Oceanic and Atmospheric Administration (NOAA) have developed a protocol for monitoring wetland elevation change and other processes important for determining the viability of wetland communities. Although focused on North Atlantic Coastal parks, this document is applicable to all coastal and inland wetland regions. Wetlands exist within a narrow range of elevation which is influenced by local hydrologic conditions. For coastal wetlands in particular, local hydrologic conditions may be changing as sea levels continue to rise. As sea level rises, coastal wetland systems may respond by building elevation to maintain favorable hydrologic conditions for their survival. This protocol provides the reader with instructions and guidelines on designing a monitoring plan or study to: A) Quantify elevation change in wetlands with the Surface Elevation Table (SET). B) Understand the processes that influence elevation change, including vertical accretion (SET and Marker Horizon methods). C) Survey the wetland surface and SET mark to a common reference datum to allow for comparing sample stations to each other and to local tidal datums. D) Survey the SET mark to monitor its relative stability. This document is divided into two parts; the main body that presents an overview of all aspects of monitoring wetland elevation dynamics, and a collection of Standard Operating Procedures (SOP) that describes in detail how to perform or execute each step of the methodology. Detailed instruction on the installation, data collection, data management and analysis are provided in this report

Radial-vertical profiles of tropical cyclone derived from dropsondes

NASA Astrophysics Data System (ADS)

Ren, Yifang

The scopes of this thesis research are two folds: the first one is to the construct the intensity-based composite radial-vertical profiles of tropical cyclones (TC) using GPS-based dropsonde observations and the second one is to identify the major deficiencies of Mathur vortices against the dropsonde composites of TCs. The intensity-based dropsonde composites of TCs advances our understanding of the dynamic and thermal structure of TCs of different intensity along the radial direction in and above the boundary layer where lies the devastating high wind that causes property damages and storm surges. The identification of the major deficiencies of Mathur vortices in representing the radial-vertical profiles of TC of different intensity helps to improve numerical predictions of TCs since most operational TC forecast models need to utilize bogus vortices, such as Mathur vortices, to initialize TC forecasts and simulations. We first screen all available GPS dropsonde data within and round 35 named TCs over the tropical Atlantic basin from 1996 to 2010 and pair them with TC parameters derived from the best-track data provided by the National Hurricane Center (NHC) and select 1149 dropsondes that have continuous coverage in the lower troposphere. The composite radial-vertical profiles of tangential wind speed, temperature, mixing ratio and humidity are based for each TC category ranging from "Tropical Storm" (TS) to "Hurricane Category 1" (H1) through "Hurricane Category 5" (H5). The key findings of the dropsonde composites are: (i) all TCs have the maximum tangential wind within 1 km above the ground and a distance of 1-2 times of the radius of maximum wind (RMW) at the surface; (ii) all TCs have a cold ring surrounding the warm core near the boundary layer at a distance of 1-3 times of the RMW and the cold ring structure gradually diminishes at a higher elevation where the warm core structure prevails along the radial direction; (iii) the existence of such shallow cold

Federal Radionavigation Plan

DTIC Science & Technology

1986-12-01

established by the Federal Aviation Administration (FAA), take into account limitations of the navigational service available, and in some airspace the Air... Services (C&GS) of the National Ocean Service , National Oceanic and Atmospheric Administration (NOS/NOAA), are based on regional horizontal datums which...Electromagnetic Interference EMS Emergency Medical Service ERDA Energy Research & Development Administration (Now Department of Energy) F 3 Form, Fit, and

Effects of vertical rotation on Arabidopsis development

NASA Technical Reports Server (NTRS)

Brown, A. H.; Chapman, D. K.; Dahl, A. O.

1975-01-01

Various gross morphological end points of Arabidopsis development are examined in an attempt to separate the effects of growth on the horizontal clinostat into a component caused by rotation alone and another component caused by the altered position with respect to the direction of the g-vector. In a series of tests which involved comparisons between vertical stationary plants, vertical rotated plants, and plants rotated on clinostats, certain characters were consistently influenced by vertical rotation alone. The characters for which this effect was statistically significant were petiole length and leaf blade width.

Adsorption to Fish Sperm of Vertically Transmitted Fish Viruses

NASA Astrophysics Data System (ADS)

Mulcahy, Dan; Pascho, Ronald J.

1984-07-01

More than 99 percent of a vertically transmitted fish rhabdovirus, infectious hematopoietic necrosis virus, was removed from suspension in less than 1 minute by adsorption to the surface membrane of sperm from two genera of salmonid fishes. The vertically transmitted, infectious pancreatic necrosis virus adsorbed to a lesser degree, but no adsorption occurred with a second fish rhabdovirus that is not vertically transmitted. Such adsorption may be involved in vertical transmission of these viruses.

Adsorption to fish sperm of vertically transmitted fish viruses

USGS Publications Warehouse

Mulcahy, D.; Pascho, R.J.

1984-01-01

More than 99 percent of a vertically transmitted fish rhabdovirus, infectious hematopoietic necrosis virus, was removed from suspension in less than 1 minute by adsorption to the surface membrane of sperm from two genera of salmonid fishes. The vertically transmitted, infectious pancreatic necrosis virus adsorbed to a lesser degree, but no adsorption occurred with a second fish rhabdovirus that is not vertically transmitted. Such adsorption may be involved in vertical transmission of these viruses.

The Kerala Decentration Meter. A new method and devise for fitting the optical of spectacle lenses in the visual axis.

PubMed

Joseph, T K; Kartha, C P

1982-01-01

Centring of spectacle lenses is much neglected field of ophthalmology. The prismatic effect caused by wrong centring results in a phoria on the eye muscles which in turn causes persistent eyestrain. The theory of visual axis, optical axis and angle alpha is discussed. Using new methods the visual axis and optical axis of 35 subjects were measured. The results were computed for facial asymmetry, parallax error, angle alpha and also decentration for near vision. The results show that decentration is required on account of each of these factors. Considerable correction is needed in the vertical direction, a fact much neglected nowadays; and vertical decentration results in vertical phoria which is more symptomatic than horizontal phorias. Angle Alpha was computed for each of these patients. A new devise called 'The Kerala Decentration Meter' using the pinhole method for measuring the degree of decentration from the datum centre of the frame, and capable of correcting all the factors described above, is shown with diagrams.

Microburst vertical wind estimation from horizontal wind measurements

NASA Technical Reports Server (NTRS)

Vicroy, Dan D.

1994-01-01

The vertical wind or downdraft component of a microburst-generated wind shear can significantly degrade airplane performance. Doppler radar and lidar are two sensor technologies being tested to provide flight crews with early warning of the presence of hazardous wind shear. An inherent limitation of Doppler-based sensors is the inability to measure velocities perpendicular to the line of sight, which results in an underestimate of the total wind shear hazard. One solution to the line-of-sight limitation is to use a vertical wind model to estimate the vertical component from the horizontal wind measurement. The objective of this study was to assess the ability of simple vertical wind models to improve the hazard prediction capability of an airborne Doppler sensor in a realistic microburst environment. Both simulation and flight test measurements were used to test the vertical wind models. The results indicate that in the altitude region of interest (at or below 300 m), the simple vertical wind models improved the hazard estimate. The radar simulation study showed that the magnitude of the performance improvement was altitude dependent. The altitude of maximum performance improvement occurred at about 300 m.

Robotic platform for traveling on vertical piping network

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nance, Thomas A; Vrettos, Nick J; Krementz, Daniel

This invention relates generally to robotic systems and is specifically designed for a robotic system that can navigate vertical pipes within a waste tank or similar environment. The robotic system allows a process for sampling, cleaning, inspecting and removing waste around vertical pipes by supplying a robotic platform that uses the vertical pipes to support and navigate the platform above waste material contained in the tank.

Observing tectonic plate motions and deformations from satellite laser ranging

NASA Technical Reports Server (NTRS)

Christodoulidis, D. C.; Smith, D. E.; Kolenkiewicz, R.; Klosko, S. M.; Torrence, M. H.

1985-01-01

The scope of geodesy has been greatly affected by the advent of artificial near-earth satellites. The present paper provides a description of the results obtained from the reduction of data collected with the aid of satellite laser ranging. It is pointed out that dynamic reduction of satellite laser ranging (SLR) data provides very precise positions in three dimensions for the laser tracking network. The vertical components of the stations, through the tracking geometry provided by the global network and the accurate knowledge of orbital dynamics, are uniquely related to the center of mass of the earth. Attention is given to the observations, the methodologies for reducing satellite observations to estimate station positions, Lageos-observed tectonic plate motions, an improved temporal resolution of SLR plate motions, and the SLR vertical datum.

Vertical bloch line memory

NASA Technical Reports Server (NTRS)

Katti, Romney R. (Inventor); Stadler, Henry L. (Inventor); Wu, Jiin-chuan (Inventor)

1995-01-01

A new read gate design for the vertical Bloch line (VBL) memory is disclosed which offers larger operating margin than the existing read gate designs. In the existing read gate designs, a current is applied to all the stripes. The stripes that contain a VBL pair are chopped, while the stripes that do not contain a VBL pair are not chopped. The information is then detected by inspecting the presence or absence of the bubble. The margin of the chopping current amplitude is very small, and sometimes non-existent. A new method of reading Vertical Bloch Line memory is also disclosed. Instead of using the wall chirality to separate the two binary states, the spatial deflection of the stripe head is used. Also disclosed herein is a compact memory which uses vertical Bloch line (VBL) memory technology for providing data storage. A three-dimensional arrangement in the form of stacks of VBL memory layers is used to achieve high volumetric storage density. High data transfer rate is achieved by operating all the layers in parallel. Using Hall effect sensing, and optical sensing via the Faraday effect to access the data from within the three-dimensional packages, an even higher data transfer rate can be achieved due to parallel operation within each layer.

Sediment Vertical Flux in Unsteady Sheet Flows

NASA Astrophysics Data System (ADS)

Hsu, T.; Jenkins, J. T.; Liu, P. L.

2002-12-01

In models for sediment suspension, two different boundary conditions have been employed at the sediment bed. Either the sediment concentration is given or the vertical flux of sediment is specified. The specification of the latter is usually called the pick-up function. Recently, several developments towards a better understanding of the sediment bed boundary condition have been reported. Nielson et al (Coastal Engineering 2002, 45, p61-68) have indicated a better performance using the sediment vertical flux as the bed boundary condition in comparisons with experimental data. Also, Drake and Calantoni (Journal of Geophysical Research 2001, 106, C9, p19859-19868) have suggested that in the nearshore environment with its various unsteady flow conditions, the appropriate sediment boundary conditions of a large-scale morphology model must consider both the magnitude the free stream velocity and the acceleration of the flow. In this research, a small-scale sheet flow model based on the two-phase theory is implemented to further study these issues. Averaged two-phase continuum equations are presented for concentrated flows of sediment that are driven by strong, fully developed, unsteady turbulent shear flows over a mobile bed. The particle inter-granular stress is modeled using collisional granular flow theory and a two-equation closure for the fluid turbulence is adopted. In the context of the two-phase theory, sediment is transported through the sediment vertical velocity. Using the fully developed sediment phase continuity equation, it can be shown that the vertical velocity of the sediment must vanish when the flow reaches a steady state. In other words, in fully developed conditions, it is the unsteadiness of the flow that induces the vertical motion of the sediment and that changes the sediment concentration profile. Therefore, implementing a boundary condition based on sediment vertical flux is consistent with both the two-phase theory and with the observation

Vertical organic transistors.

PubMed

Lüssem, Björn; Günther, Alrun; Fischer, Axel; Kasemann, Daniel; Leo, Karl

2015-11-11

Organic switching devices such as field effect transistors (OFETs) are a key element of future flexible electronic devices. So far, however, a commercial breakthrough has not been achieved because these devices usually lack in switching speed (e.g. for logic applications) and current density (e.g. for display pixel driving). The limited performance is caused by a combination of comparatively low charge carrier mobilities and the large channel length caused by the need for low-cost structuring. Vertical Organic Transistors are a novel technology that has the potential to overcome these limitations of OFETs. Vertical Organic Transistors allow to scale the channel length of organic transistors into the 100 nm regime without cost intensive structuring techniques. Several different approaches have been proposed in literature, which show high output currents, low operation voltages, and comparatively high speed even without sub-μm structuring technologies. In this review, these different approaches are compared and recent progress is highlighted.

Vertical integration from the large Hilbert space

NASA Astrophysics Data System (ADS)

Erler, Theodore; Konopka, Sebastian

2017-12-01

We develop an alternative description of the procedure of vertical integration based on the observation that amplitudes can be written in BRST exact form in the large Hilbert space. We relate this approach to the description of vertical integration given by Sen and Witten.

Beyond vertical integration--Community based medical education.

PubMed

Kennedy, Emma Margaret

2006-11-01

The term 'vertical integration' is used broadly in medical education, sometimes when discussing community based medical education (CBME). This article examines the relevance of the term 'vertical integration' and provides an alternative perspective on the complexities of facilitating the CBME process. The principles of learner centredness, patient centredness and flexibility are fundamental to learning in the diverse contexts of 'community'. Vertical integration as a structural concept is helpful for academic organisations but has less application to education in the community setting; a different approach illuminates the strengths and challenges of CBME that need consideration by these organisations.

Longitudinal Differences of Ionospheric Vertical Density Distribution and Equatorial Electrodynamics

NASA Technical Reports Server (NTRS)

Yizengaw, E.; Zesta, E.; Moldwin, M. B.; Damtie, B.; Mebrahtu, A.; Valledares, C.E.; Pfaff, R. F.

2012-01-01

Accurate estimation of global vertical distribution of ionospheric and plasmaspheric density as a function of local time, season, and magnetic activity is required to improve the operation of space-based navigation and communication systems. The vertical density distribution, especially at low and equatorial latitudes, is governed by the equatorial electrodynamics that produces a vertical driving force. The vertical structure of the equatorial density distribution can be observed by using tomographic reconstruction techniques on ground-based global positioning system (GPS) total electron content (TEC). Similarly, the vertical drift, which is one of the driving mechanisms that govern equatorial electrodynamics and strongly affect the structure and dynamics of the ionosphere in the low/midlatitude region, can be estimated using ground magnetometer observations. We present tomographically reconstructed density distribution and the corresponding vertical drifts at two different longitudes: the East African and west South American sectors. Chains of GPS stations in the east African and west South American longitudinal sectors, covering the equatorial anomaly region of meridian approx. 37 deg and 290 deg E, respectively, are used to reconstruct the vertical density distribution. Similarly, magnetometer sites of African Meridian B-field Education and Research (AMBER) and INTERMAGNET for the east African sector and South American Meridional B-field Array (SAMBA) and Low Latitude Ionospheric Sensor Network (LISN) are used to estimate the vertical drift velocity at two distinct longitudes. The comparison between the reconstructed and Jicamarca Incoherent Scatter Radar (ISR) measured density profiles shows excellent agreement, demonstrating the usefulness of tomographic reconstruction technique in providing the vertical density distribution at different longitudes. Similarly, the comparison between magnetometer estimated vertical drift and other independent drift observation

Interpretations of Complete Bouguer Gravity Anomalies from the GRAV-D Project in Alaska

NASA Astrophysics Data System (ADS)

Diehl, T. M.; Preaux, S. A.; Childers, V. A.

2010-12-01

The GRAV-D (Gravity for the Redefinition of the American Vertical Datum) Project of the U.S. National Geodetic Survey plans to collect airborne gravity data across the entire U.S. and its holdings over the next decade. The goal of the project is to create a gravimetric geoid model to use as the vertical datum for the U.S. by 2021. Airborne gravity survey work began more than two years ago, with Alaska as a high priority for new data collection. Data collection there is underway and will be ongoing for several more years, but two roughly 400 km x 400 km surveys have been completed: in 2008 (centered over Cook Inlet near Anchorage) and in 2009 (centered over the Interior, to the north of the Alaska Range and west of Fairbanks). The gravity data for both surveys was collected with a MicroG LaCoste TAGS system but each survey utilized a different aircraft and survey layout. The 2008 survey was flown at 35,000 ft with the NOAA Cessna Citation jet, with 10 km data line spacing and 60 km cross lines spacing. The 2009 survey was flown at 12,500 ft with the Naval Research Lab King Air (RC-12) turboprop, with 7.5 km data line spacing and 37.5 cross line spacing. The 2008 data reveal the > 20 km resolution gravity effects of all the near-trench features (from accretionary prism to volcanic arc) for a 400 km stretch of the active plate boundary. In comparison, the 2009 gravity data allow a slightly better resolution (> 15 km) view of the distal deformation to the north of the Alaska Range. The free-air gravity disturbances for each survey were computed and then complete (terrain-corrected) Bouguer gravity anomalies were calculated with Gauss-Legendre Quadrature integration (von Frese, et al., 1999) using standard density assumptions. Topography used to calculate the corrections came from the freely-available GTOPO30 (USGS, online) and bathymetry from the Smith and Sandwell (1997) altimetry-derived data. Interpretations of the complete Bouguer gravity anomalies will be made in

Decline of vertical gaze and convergence with aging.

PubMed

Oguro, Hiroaki; Okada, Kazunori; Suyama, Nobuo; Yamashita, Kazuya; Yamaguchi, Shuhei; Kobayashi, Shotai

2004-01-01

Disturbance of vertical eye movement and ocular convergence is often observed in elderly people, but little is known about its frequency. The purpose of this study was to investigate age-associated changes in vertical eye movement and convergence in healthy elderly people, using a digital video camera system. We analyzed vertical eye movements and convergence in 113 neurologically normal elderly subjects (mean age 70 years) in comparison with 20 healthy young controls (mean age 32 years). The range of vertical eye movement was analyzed quantitatively and convergence was analyzed qualitatively. In the elderly subjects, the angle of vertical gaze decreased with advancing age and it was significantly smaller than that of the younger subjects. The mean angle of upward gaze was significantly smaller than that of downward gaze for both young and elderly subjects. Upward gaze impairment became apparent in subjects in their 70s, and downward gaze impairment in subjects in their 60s. Disturbance in convergence also increased with advancing age, and was found in 40.7% of the elderly subjects. These findings indicate that the mechanisms of age-related change are different for upward and downward vertical gaze. Digital video camera monitoring was useful for assessing and monitoring eye movements. Copyright 2004 S. Karger AG, Basel

46 CFR 190.10-15 - Vertical ladders not accepted.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Vertical ladders not accepted. 190.10-15 Section 190.10-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OCEANOGRAPHIC RESEARCH VESSELS CONSTRUCTION AND ARRANGEMENT Means of Escape § 190.10-15 Vertical ladders not accepted. (a) Vertical ladders...

Negative differential resistance observed from vertical p+-n+ junction device with two-dimensional black phosphorous

NASA Astrophysics Data System (ADS)

Lee, Daeyeong; Jang, Young Dae; Kweon, Jaehwan; Ryu, Jungjin; Hwang, Euyheon; Yoo, Won Jong; Samsung-SKKU Graphene/2D Center (SSGC) Collaboration

A vertical p+-n+ homojunction was fabricated by using black phosphorus (BP) as a van der Waals two-dimensional (2D) material. The top and bottom layers of the materials were doped by chemical dopants of gold chloride (AuCl3) for p-type doping and benzyl viologen (BV) for n-type doping. The negative differential resistance (NDR) effect was clearly observed from the output curves of the fabricated BP vertical devices. The thickness range of the 2D material showing NDR and the peak to valley current ratio of NDR are found to be strongly dependent on doping condition, gate voltage, and BP's degradation level. Furthermore, the carrier transport of the p+-n+ junction was simulated by using density functional theory (DFT) and non-equilibrium Green's function (NEGF). Both the experimental and simulation results confirmed that the NDR is attributed to the band-to-band tunneling (BTBT) across the 2D BP p+-n+ junction, and further quantitative details on the carrier transport in the vertical p+-n+ junction devices were explored, according to the analyses of the measured transfer curves and the DFT simulation results. This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MEST) (2013R1A2A2A01015516).

Kinematic and diabatic vertical velocity climatologies from a chemistry climate model

NASA Astrophysics Data System (ADS)

Marinke Hoppe, Charlotte; Ploeger, Felix; Konopka, Paul; Müller, Rolf

2016-05-01

The representation of vertical velocity in chemistry climate models is a key element for the representation of the large-scale Brewer-Dobson circulation in the stratosphere. Here, we diagnose and compare the kinematic and diabatic vertical velocities in the ECHAM/Modular Earth Submodel System (MESSy) Atmospheric Chemistry (EMAC) model. The calculation of kinematic vertical velocity is based on the continuity equation, whereas diabatic vertical velocity is computed using diabatic heating rates. Annual and monthly zonal mean climatologies of vertical velocity from a 10-year simulation are provided for both kinematic and diabatic vertical velocity representations. In general, both vertical velocity patterns show the main features of the stratospheric circulation, namely, upwelling at low latitudes and downwelling at high latitudes. The main difference in the vertical velocity pattern is a more uniform structure for diabatic and a noisier structure for kinematic vertical velocity. Diabatic vertical velocities show higher absolute values both in the upwelling branch in the inner tropics and in the downwelling regions in the polar vortices. Further, there is a latitudinal shift of the tropical upwelling branch in boreal summer between the two vertical velocity representations with the tropical upwelling region in the diabatic representation shifted southward compared to the kinematic case. Furthermore, we present mean age of air climatologies from two transport schemes in EMAC using these different vertical velocities and analyze the impact of residual circulation and mixing processes on the age of air. The age of air distributions show a hemispheric difference pattern in the stratosphere with younger air in the Southern Hemisphere and older air in the Northern Hemisphere using the transport scheme with diabatic vertical velocities. Further, the age of air climatology from the transport scheme using diabatic vertical velocities shows a younger mean age of air in the

Feasibility of Measuring Mean Vertical Motion for Estimating Advection. Chapter 6

NASA Technical Reports Server (NTRS)

Vickers, Dean; Mahrt, L.

2005-01-01

Numerous recent studies calculate horizontal and vertical advection terms for budget studies of net ecosystem exchange of carbon. One potential uncertainty in such studies is the estimate of mean vertical motion. This work addresses the reliability of vertical advection estimates by contrasting the vertical motion obtained from the standard practise of measuring the vertical velocity and applying a tilt correction, to the vertical motion calculated from measurements of the horizontal divergence of the flow using a network of towers. Results are compared for three different tilt correction methods. Estimates of mean vertical motion are sensitive to the choice of tilt correction method. The short-term mean (10 to 60 minutes) vertical motion based on the horizontal divergence is more realistic compared to the estimates derived from the standard practise. The divergence shows long-term mean (days to months) sinking motion at the site, apparently due to the surface roughness change. Because all the tilt correction methods rely on the assumption that the long-term mean vertical motion is zero for a given wind direction, they fail to reproduce the vertical motion based on the divergence.

Investigating Methods for Serving Visualizations of Vertical Profiles

NASA Astrophysics Data System (ADS)

Roberts, J. T.; Cechini, M. F.; Lanjewar, K.; Rodriguez, J.; Boller, R. A.; Baynes, K.

2017-12-01

Several geospatial web servers, web service standards, and mapping clients exist for the visualization of two-dimensional raster and vector-based Earth science data products. However, data products with a vertical component (i.e., vertical profiles) do not have the same mature set of technologies and pose a greater technical challenge when it comes to visualizations. There are a variety of tools and proposed standards, but no obvious solution that can handle the variety of visualizations found with vertical profiles. An effort is being led by members of the NASA Global Imagery Browse Services (GIBS) team to gather a list of technologies relevant to existing vertical profile data products and user stories. The goal is to find a subset of technologies, standards, and tools that can be used to build publicly accessible web services that can handle the greatest number of use cases for the widest audience possible. This presentation will describe results of the investigation and offer directions for moving forward with building a system that is capable of effectively and efficiently serving visualizations of vertical profiles.

Vertical Integration, Monopoly, and the First Amendment.

ERIC Educational Resources Information Center

Brennan, Timothy J.

This paper addresses the relationship between the First Amendment, monopoly of transmission media, and vertical integration of transmission and content provision. A survey of some of the incentives a profit-maximizing transmission monopolist may have with respect to content is followed by a discussion of how vertical integration affects those…

Vertical Hegelianism and Beyond: Digital Cinema Editing.

ERIC Educational Resources Information Center

Wyatt, Roger B.

Cinema as an art and communication form is entering its second century of development. Sergei Eisenstein conceived of editing in horizontal and vertical terms. He saw vertical editing patterns primarily as the synchronization of simultaneous image and sound elements, particularly music, no create cinematic meaning by means of the relationship…

Vertical load capacities of roof truss cross members.

PubMed

Gearhart, David F; Morsy, Mohamed Khaled

2016-05-01

Trusses used for roof support in coal mines are constructed of two grouted bolts installed at opposing forty-five degree angles into the roof and a cross member that ties the angled bolts together. The load on the cross member is vertical, which is transverse to the longitudinal axis, and therefore the cross member is loaded in the weakest direction. Laboratory tests were conducted to determine the vertical load capacity and deflection of three different types of cross members. Single-point load tests, with the load applied in the center of the specimen and double-point load tests, with a span of 2.4 m, were conducted. For the single-point load configuration, the yield of the 25 mm solid bar cross member was nominally 98 kN of vertical load, achieved at 42 cm of deflection. For cable cross members, yield was not achieved even after 45 cm of deflection. Peak vertical loads were about 89 kN for 17 mm cables and 67 kN for the 15 mm cables. For the double-point load configurations, the 25 mm solid bar cross members yielded at 150 kN of vertical load and 25 cm of deflection. At 25 cm of deflection individual cable strands started breaking at 133 and 111 kN of vertical load for the 17 and 15 mm cable cross members respectively.

Estimating Vertical Land Motion in the Chesapeake Bay

NASA Astrophysics Data System (ADS)

Houttuijn Bloemendaal, L.; Hensel, P.

2017-12-01

This study aimed to provide a modern measurement of subsidence in the Chesapeake Bay region and establish a methodology for measuring vertical land motion using static GPS, a cheaper alternative to InSAR or classical leveling. Vertical land motion in this area is of particular concern because tide gages are showing up to 5 mm/yr of local, relative sea level rise. While a component of this rate is the actual eustatic sea level rise itself, part of the trend may also be vertical land motion, in which subsidence exacerbates the effects of actual changes in sea level. Parts of this region are already experiencing an increase in the frequency and magnitude of near-shore coastal flooding, but the last comprehensive study of vertical land motion in this area was conducted by NOAA in 1974 (Holdahl & Morrison) using repeat leveled lines. More recent measures of vertical land motion can help inform efforts on resilience to sea level rise, such as in the Hampton Roads area. This study used measured GPS-derived vertical heights in conjunction with legacy GPS data to calculate rates of vertical motion at several points in time for a selection of benchmarks scattered throughout the region. Seventeen marks in the stable Piedmont area and in the areas suspected of subsidence in the Coastal Plain were selected for the analysis. Results indicate a significant difference between the rates of vertical motion in the Piedmont and Coastal Plain, with a mean rate of -4.10 mm/yr in the Coastal Plain and 0.15 mm/yr in the Piedmont. The rates indicate particularly severe subsidence at the southern Delmarva Peninsula coast and the Hampton-Roads area, with a mean rate of -6.57 mm/yr in that region. By knowing local rates of subsidence as opposed to sea level change itself, coastal managers may make better informed decisions regarding natural resource use, such as deciding whether or not to reduce subsurface fluid withdrawals or to consider injecting treated water back into the aquifer to slow

Muscle activation history at different vertical jumps and its influence on vertical velocity.

PubMed

Kopper, Bence; Csende, Zsolt; Sáfár, Sándor; Hortobágyi, Tibor; Tihanyi, József

2013-02-01

In the present study we investigated displacement, time, velocity and acceleration history of center of mass (COM) and electrical activity of knee extensors to estimate the dominance of the factors influencing the vertical velocity in squat jumps (SJs), countermovement jumps (CMJs) and drop jumps (DJs) performed with small (40°) and large (80°) range of joint motion (SROM and LROM). The maximum vertical velocity (v4) was 23.4% (CMJ) and 7.8% (DJ) greater when the jumps were performed with LROM compared with SROM (p < 0.05). These differences are considerably less than it could be expected from the greater COM and knee angular displacement and duration of active state. This small difference can be attributed to the greater deceleration during eccentric phase (CMJ:32.1%, DJ:91.5%) in SROM than that in LROM. v4 was greater for SJ in LROM than for SJ in SROM indicating the significance of the longer active state and greater activation level (p < 0.001). The difference in v4 was greater between SJ and CMJ in SROM (38.6%) than in LROM (9.0%), suggesting that elastic energy storage and re-use can be a dominant factor in the enhancement of vertical velocity of CMJ and DJ compared with SJ performed with SROM. Copyright © 2012 Elsevier Ltd. All rights reserved.

Linking Primary Care Information Systems and Public Health Vertical Programs in the Philippines: An Open-source Experience

PubMed Central

Tolentino, Herman; Marcelo, Alvin; Marcelo, Portia; Maramba, Inocencio

2005-01-01

Community-based primary care information systems are one of the building blocks for national health information systems. In the Philippines, after the devolution of health care to local governments, we observed “health information system islands” connected to national vertical programs being implemented in devolved health units. These structures lead to a huge amount of “information work” in the transformation of health information at the community level. This paper describes work done to develop and implement the open-source Community Based Health Information Tracking System (CHITS) Project, which was implemented to address this information management problem and its outcomes. Several lessons learned from the field as well as software development strategies are highlighted in building community level information systems that link to national level health information systems. PMID:16779052

Tilt Nacelle Vertical and Short Takeoff and Landing Engine

NASA Image and Video Library

1979-03-21

Center Director John McCarthy, left, and researcher Al Johns pose with a one-third scale model of a Grumman Aerospace tilt engine nacelle for Vertical and Short Takeoff and Landing (V/STOL) in the 9- by 15-Foot Low Speed Wind Tunnel at the National Aeronautics and Space Administration (NASA) Lewis Research Center. Lewis researchers had been studying tilt nacelle and inlet issues for several years. One area of concern was the inlet flow separation during the transition from horizontal to vertical flight. The separation of air flow from the inlet’s internal components could significantly stress the fan blades or cause a loss of thrust. In 1978 NASA researchers Robert Williams and Al Johns teamed with Grumman’s H.C. Potonides to develop a series of tests in the Lewis 9- by 15-foot tunnel to study a device designed to delay the flow separation by blowing additional air into the inlet. A jet of air, supplied through the hose on the right, was blown over the inlet surfaces. The researchers verified that the air jet slowed the flow separation. They found that the blowing on boundary layer control resulted in a doubling of the angle-of-attack and decreases in compressor blade stresses and fan distortion. The tests were the first time the concept of blowing air for boundary layer control was demonstrated. Boundary layer control devices like this could result in smaller and lighter V/STOL inlets.

Advanced BCD technology with vertical DMOS based on a semi-insulation structure

NASA Astrophysics Data System (ADS)

Kui, Ma; Xinghua, Fu; Jiexin, Lin; Fashun, Yang

2016-07-01

A new semi-insulation structure in which one isolated island is connected to the substrate was proposed. Based on this semi-insulation structure, an advanced BCD technology which can integrate a vertical device without extra internal interconnection structure was presented. The manufacturing of the new semi-insulation structure employed multi-epitaxy and selectively multi-doping. Isolated islands are insulated with the substrate by reverse-biased PN junctions. Adjacent isolated islands are insulated by isolation wall or deep dielectric trenches. The proposed semi-insulation structure and devices fixed in it were simulated through two-dimensional numerical computer simulators. Based on the new BCD technology, a smart power integrated circuit was designed and fabricated. The simulated and tested results of Vertical DMOS, MOSFETs, BJTs, resistors and diodes indicated that the proposed semi-insulation structure is reasonable and the advanced BCD technology is validated. Project supported by the National Natural Science Foundation of China (No. 61464002), the Science and Technology Fund of Guizhou Province (No. Qian Ke He J Zi [2014]2066), and the Dr. Fund of Guizhou University (No. Gui Da Ren Ji He Zi (2013)20Hao).

Religious Affiliation and the Fertility of Married Couples.

ERIC Educational Resources Information Center

Mosher, William D.; Hendershot, Gerry E.

1984-01-01

Used data from two National Surveys of Family Growth (N=14,000) to estimate the fertility of married couples by religious group. Results are presented in terms of religious and racial differences, controlling for age, education and residence, and indicate that religious affiliation continues to be an indispensable datum. (JAC)

Strong parameterization and coordination encirclements of graph of Penrose tiling vertices

NASA Astrophysics Data System (ADS)

Shutov, A. V.; Maleev, A. V.

2017-07-01

The coordination encirclements in a graph of Penrose tiling vertices have been investigated based on the analysis of vertice parameters. A strong parameterization of these vertices is developed in the form of a tiling of a parameter set in the region corresponding to different first coordination encirclements of vertices. An algorithm for constructing tilings of a set of parameters determining different coordination encirclements in a graph of Penrose tiling vertices of order n is proposed.

Surface Gravity Data Contribution to the Puerto Rico and U.S. Virgin Islands Geoid Model

NASA Astrophysics Data System (ADS)

Li, X.; Gerhards, C.; Holmes, S. A.; Saleh, J.; Shaw, B.

2015-12-01

The Gravity for the Redefinition of the American Vertical Datum (GRAV-D) project provides updated local gravity field information for the XGEOID15 models. In particular, its airborne gravity data in the area of Puerto Rico and U.S. Virgin Islands (PRVI) made substantial improvements (~60%) on the precision of the geoid models at the local GNSS/Leveling bench marks in the target area. Fortunately, PRVI is free of the huge systematic error in the North American Vertical Datum of 1988 (NAVD88). Thus, the airborne contribution was evaluated more realistically. In addition, the airborne data picked up more detailed gravity field information in the medium wavelength band (spherical harmonic degree 200 to 600) that are largely beyond the resolution of the current satellite missions, especially along the nearby ocean trench areas. Under this circumstance (significant airborne contributions in the medium band), local surface gravity data need to be examined more carefully than before during merging with the satellite and airborne information for local geoid improvement, especially considering the well-known systematic problems in the NGS historical gravity holdings (Saleh et al 2013 JoG). Initial tests showed that it is very important to maintain high consistency between the surface data sets and the airborne enhanced reference model. In addition, a new aggregation method (Gerhards 2014, Inverse Problems) will also be tested to optimally combine the local surface data with the reference model. The data cleaning and combining procedures in the target area will be summarized here as reference for future applications.

Resultant vertical prism in toric soft contact lenses.

PubMed

Sulley, Anna; Hawke, Ryan; Lorenz, Kathrine Osborn; Toubouti, Youssef; Olivares, Giovanna

2015-08-01

Rotational stability of toric soft contact lenses (TSCLs) is achieved using a range of designs. Designs utilising prism or peripheral ballast may result in residual prism in the optic zone. This study quantifies the vertical prism in the central 6mm present in TSCLs with various stabilisation methods. Vertical prism was computed using published refractive index and vertical thickness changes in the central optic zone on a full lens thickness map. Thickness maps were measured using scanning transmission microscopy. Designs tested were reusable, silicone hydrogel and hydrogel TSCLs: SofLens(®) Toric, PureVision(®)2 for Astigmatism, PureVision(®) Toric, Biofinity(®) Toric, Avaira(®) Toric, clariti(®) toric, AIR OPTIX(®) for ASTIGMATISM and ACUVUE OASYS(®) for ASTIGMATISM; with eight parameter combinations for each lens (-6.00DS to +3.00DS, -1.25DC, 90° and 180° axes). All TSCL designs evaluated had vertical prism in the optic zone except one which had virtually none (0.01Δ). Mean prism ranged from 0.52Δ to 1.15Δ, with three designs having prism that varied with sphere power. Vertical prism in ACUVUE OASYS(®) for ASTIGMATISM was significantly lower than all other TSCLs tested. TSCL designs utilising prism-ballast and peri-ballast for stabilisation have vertical prism in the central optic zone. In monocular astigmats fitted with a TSCL or those wearing a mix of toric designs, vertical prism imbalance could create or exacerbate disturbances in binocular vision function. Practitioners should be aware of this potential effect when selecting which TSCL designs to prescribe, particularly for monocular astigmats with pre-existing binocular vision anomalies, and when managing complaints of asthenopia in monocular astigmats. Copyright © 2015 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Climatology of Neutral vertical winds in the midlatitude thermosphere

NASA Astrophysics Data System (ADS)

Kerr, R.; Kapali, S.; Riccobono, J.; Migliozzi, M. A.; Noto, J.; Brum, C. G. M.; Garcia, R.

2017-12-01

More than one thousand measurements of neutral vertical winds, relative to an assumed average of 0 m/s during a nighttime period, have been made at Arecibo Observatory and the Millstone Hill Optical Facility since 2012, using imaging Fabry-Perot interferometers. These instruments, tuned to the 630 nm OI emission, are carefully calibrated for instrumental frequency drift using frequency stabilized lasers, allowing isolation of Doppler motion in the zenith with 1-2 m/s accuracy. As one example of the results, relative vertical winds at Arecibo during quiet geomagnetic conditions near winter solstice 2016, range ±70 m/s and have a one standard deviation statistical variability of ±34 m/s. This compares with a ±53 m/s deviation from the average meridional wind, and a ±56 m/s deviation from the average zonal wind measured during the same period. Vertical neutral wind velocities for all periods range from roughly 30% - 60% of the horizontal velocity domain at Arecibo. At Millstone Hill, the vertical velocities relative to horizontal velocities are similar, but slightly smaller. The midnight temperature maximum at Arecibo is usually correlated with a surge in the upward wind, and vertical wind excursions of more than 80 m/s are common during magnetic storms at both sites. Until this compilation of vertical wind climatology, vertical motions of the neutral atmosphere outside of the auroral zone have generally been assumed to be very small compared to horizontal transport. In fact, excursions from small vertical velocities in the mid-latitude thermosphere near the F2 ionospheric peak are common, and are not isolated events associated with unsettled geomagnetic conditions or other special dynamic conditions.

Vertical exploration and dimensional modularity in mice

PubMed Central

Benjamini, Yoav; Golani, Ilan

2018-01-01

Exploration is a central component of animal behaviour studied extensively in rodents. Previous tests of free exploration limited vertical movement to rearing and jumping. Here, we attach a wire mesh to the arena wall, allowing vertical exploration. This provides an opportunity to study the morphogenesis of behaviour along the vertical dimension, and examine the context in which it is performed. In the current set-up, the mice first use the doorway as a point reference for establishing a borderline linear path along the circumference of the arena floor, and then use this path as a linear reference for performing horizontal forays towards the centre (incursions) and vertical forays on the wire mesh (ascents). Vertical movement starts with rearing on the wall, and commences with straight vertical ascents that increase in extent and complexity. The mice first reach the top of the wall, then mill about within circumscribed horizontal sections, and then progress horizontally for increasingly longer distances on the upper edge of the wire mesh. Examination of the sequence of borderline segments, incursions and ascents reveals dimensional modularity: an initial series (bout) of borderline segments precedes alternating bouts of incursions and bouts of ascents, thus exhibiting sustained attention to each dimension separately. The exhibited separate growth in extent and in complexity of movement and the sustained attention to each of the three dimensions disclose the mice's modular perception of this environment and validate all three as natural kinds. PMID:29657827

Vertical motion simulator familiarization guide

NASA Technical Reports Server (NTRS)

Danek, George L.

1993-01-01

The Vertical Motion Simulator Familiarization Guide provides a synoptic description of the Vertical Motion Simulator (VMS) and descriptions of the various simulation components and systems. The intended audience is the community of scientists and engineers who employ the VMS for research and development. The concept of a research simulator system is introduced and the building block nature of the VMS is emphasized. Individual sections describe all the hardware elements in terms of general properties and capabilities. Also included are an example of a typical VMS simulation which graphically illustrates the composition of the system and shows the signal flow among the elements and a glossary of specialized terms, abbreviations, and acronyms.

Vertical and Lateral Electron Content in the Martian Ionosphere

NASA Astrophysics Data System (ADS)

Paetzold, M. P.; Peter, K.; Bird, M. K.; Häusler, B.; Tellmann, S.

2016-12-01

The radio-science experiment MaRS (Mars Express Radio Science) on the Mars Express spacecraft sounds the neutral atmosphere and ionosphere of Mars since 2004. Approximately 800 vertical profiles of the ionospheric electron density have been acquired until today. The vertical electron content (TEC) is easily computed from the vertical electron density profile by integrating along the altitude. The TEC is typically a fraction of a TEC unit (1E16 m^-2) and depends on the solar zenith angle. The magnitude of the TEC is however fully dominated by the electron density contained in the main layer M2. The contributions by the M1 layer below M2 or the topside is marginal. MaRS is using two radio frequencies for the sounding of the ionosphere. The directly observed differential Doppler from the two received frequencies is a measure of the lateral electron content that means along the ray path and perpendicular to the vertical electron density profile. Combining both the vertical electron density profile, the vertical TEC and the directly observed lateral TEC describes the lateral electron density distribution in the ionosphere.

Use of temperature profiles beneath streams to determine rates of vertical ground-water flow and vertical hydraulic conductivity

USGS Publications Warehouse

Lapham, Wayne W.

1989-01-01

The use of temperature profiles beneath streams to determine rates of vertical ground-water flow and effective vertical hydraulic conductivity of sediments was evaluated at three field sites by use of a model that numerically solves the partial differential equation governing simultaneous vertical flow of fluid and heat in the Earth. The field sites are located in Hardwick and New Braintree, Mass., and in Dover, N.J. In New England, stream temperature varies from about 0 to 25 ?C (degrees Celsius) during the year. This stream-temperature fluctuation causes ground-water temperatures beneath streams to fluctuate by more than 0.1 ?C during a year to a depth of about 35 ft (feet) in fine-grained sediments and to a depth of about 50 ft in coarse-grained sediments, if ground-water velocity is 0 ft/d (foot per day). Upward flow decreases the depth affected by stream-temperature fluctuation, and downward flow increases the depth. At the site in Hardwick, Mass., ground-water flow was upward at a rate of less than 0.01 ft/d. The maximum effective vertical hydraulic conductivity of the sediments underlying this site is 0.1 ft/d. Ground-water velocities determined at three locations at the site in New Braintree, Mass., where ground water discharges naturally from the underlying aquifer to the Ware River, ranged from 0.10 to 0.20 ft/d upward. The effective vertical hydraulic conductivity of the sediments underlying this site ranged from 2.4 to 17.1 ft/d. Ground-water velocities determined at three locations at the Dover, N.J., site, where infiltration from the Rockaway River into the underlying sediments occurs because of pumping, were 1.5 ft/d downward. The effective vertical hydraulic conductivity of the sediments underlying this site ranged from 2.2 to 2.5 ft/d. Independent estimates of velocity at two of the three sites are in general agreement with the velocities determined using temperature profiles. The estimates of velocities and conductivities derived from the

Decoration of vertical graphene with aerosol nanoparticles for gas sensing

NASA Astrophysics Data System (ADS)

Cui, Shumao; Guo, Xiaoru; Ren, Ren; Zhou, Guihua; Chen, Junhong

2015-08-01

A facile method was demonstrated to decorate aerosol Ag nanoparticles onto vertical graphene surfaces using a mini-arc plasma reactor. The vertical graphene was directly grown on a sensor electrode using a plasma-enhanced chemical vapor deposition (PECVD) method. The aerosol Ag nanoparticles were synthesized by a simple vapor condensation process using a mini-arc plasma source. Then, the nanoparticles were assembled on the surface of vertical graphene through the assistance of an electric field. Based on our observation, nonagglomerated Ag nanoparticles formed in the gas phase and were assembled onto vertical graphene sheets. Nanohybrids of Ag nanoparticle-decorated vertical graphene were characterized for ammonia gas detection at room temperature. The vertical graphene served as the conductance channel, and the conductance change upon exposure to ammonia was used as the sensing signal. The sensing results show that Ag nanoparticles significantly improve the sensitivity, response time, and recovery time of the sensor.

Some Studies in Large-Scale Surface Fluxes and Vertical Motions Associated with Land falling Hurricane Katrina over the Gulf of Mexico

NASA Astrophysics Data System (ADS)

Reddy, S. R.

2010-12-01

We investigated the possible relationship between the large- scale heat fluxes and intensity change associated with the landfall of Hurricane Katrina. After reaching the category 5 intensity on August 28th , 2005 over the central Gulf of Mexico, Katrina weekend to category 3 before making landfall (August 29th , 2005) on the Louisiana coast with the maximum sustained winds of over 110 knots. We also examined the vertical motions associated with the intensity change of the hurricane. The data on Convective Available Potential Energy (CAPE), sea level pressure and wind speed were obtained from the Atmospheric Soundings, and NOAA National Hurricane Center (NHC), respectively for the period August 24 to September 3, 2005. We developed an empirical model and a C++ program to calculate surface potential temperatures and heat fluxes using the above data. We also computed vertical motions using CAPE values. The study showed that the large-scale heat fluxes reached maximum (7960W/m2) with the central pressure 905mb. The Convective Available Potential Energy and the vertical motions peaked 3-5 days before landfall. The large atmospheric vertical motions associated with the land falling hurricane Katrina produced severe weather including thunderstorms and tornadoes.

A study of rotor and platform design trade-offs for large-scale floating vertical axis wind turbines

NASA Astrophysics Data System (ADS)

Griffith, D. Todd; Paquette, Joshua; Barone, Matthew; Goupee, Andrew J.; Fowler, Matthew J.; Bull, Diana; Owens, Brian

2016-09-01

Vertical axis wind turbines are receiving significant attention for offshore siting. In general, offshore wind offers proximity to large populations centers, a vast & more consistent wind resource, and a scale-up opportunity, to name a few beneficial characteristics. On the other hand, offshore wind suffers from high levelized cost of energy (LCOE) and in particular high balance of system (BoS) costs owing to accessibility challenges and limited project experience. To address these challenges associated with offshore wind, Sandia National Laboratories is researching large-scale (MW class) offshore floating vertical axis wind turbines (VAWTs). The motivation for this work is that floating VAWTs are a potential transformative technology solution to reduce offshore wind LCOE in deep-water locations. This paper explores performance and cost trade-offs within the design space for floating VAWTs between the configurations for the rotor and platform.

Response of ramus following vertical lengthening with distraction osteogenesis.

PubMed

Tuzuner-Oncul, Aysegul Mine; Kisnisci, Reha S

2011-09-01

Vertical lengthening of the mandibular ramus is considered to be one of the least stable surgical procedures in the management of musculoskeletal maxillofacial deformities. The aim of this study was to evaluate the response of the mandibular ramus following vertical lengthening by means of distraction osteogenesis. This study included eight non-syndromic adult patients with temporomandibular joint ankylosis. The vertical height deficiency of the mandibular ramus and the ramus/condyle unit on the affected side were simultaneously reconstructed by transportation of a bone segment using distraction osteogenesis following gap arthroplasty. Lateral and posteroanterior (PA) cephalograms taken postoperatively before active distraction, at the completion of distraction and 6, 12, 24 months after distraction, were compared to evaluate the changes of the ramus height. In all cases the vertical ramus and ramus/condyle unit height loss were successfully reconstructed by distraction osteogenesis. There was no relapse in the amount of height gained by distraction osteogenesis at the 24 months follow-up review (p>0.05). Acute one stage vertical lengthening of the mandibular ramus is considered to be one of the least stable musculoskeletal procedures with relapse being a significant adverse outcome. In this clinical study gradual vertical lengthening of the ramus through ramus/condyle unit distraction osteogenesis has maintained the initial vertical ramus height gained for 24 months. Copyright © 2010 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Direct Observation of Ultralow Vertical Emittance using a Vertical Undulator - presentation slides

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wootton, Kent

2015-09-17

Direct emittance measurement based on vertical undulator is discussed. Emittance was evaluated from peak ratios, the smallest measured being =0.9 ±0.3 pm rad. The angular distribution of undulator radiation departs from Gaussian approximations, a fact of which diffraction-limited light sources should be aware.

The vertical variability of hyporheic fluxes inferred from riverbed temperature data

NASA Astrophysics Data System (ADS)

Cranswick, Roger H.; Cook, Peter G.; Shanafield, Margaret; Lamontagne, Sebastien

2014-05-01

We present detailed profiles of vertical water flux from the surface to 1.2 m beneath the Haughton River in the tropical northeast of Australia. A 1-D numerical model is used to estimate vertical flux based on raw temperature time series observations from within downwelling, upwelling, neutral, and convergent sections of the hyporheic zone. A Monte Carlo analysis is used to derive error bounds for the fluxes based on temperature measurement error and uncertainty in effective thermal diffusivity. Vertical fluxes ranged from 5.7 m d-1 (downward) to -0.2 m d-1 (upward) with the lowest relative errors for values between 0.3 and 6 m d-1. Our 1-D approach provides a useful alternative to 1-D analytical and other solutions because it does not incorporate errors associated with simplified boundary conditions or assumptions of purely vertical flow, hydraulic parameter values, or hydraulic conditions. To validate the ability of this 1-D approach to represent the vertical fluxes of 2-D flow fields, we compare our model with two simple 2-D flow fields using a commercial numerical model. These comparisons showed that: (1) the 1-D vertical flux was equivalent to the mean vertical component of flux irrespective of a changing horizontal flux; and (2) the subsurface temperature data inherently has a "spatial footprint" when the vertical flux profiles vary spatially. Thus, the mean vertical flux within a 2-D flow field can be estimated accurately without requiring the flow to be purely vertical. The temperature-derived 1-D vertical flux represents the integrated vertical component of flux along the flow path intersecting the observation point. This article was corrected on 6 JUN 2014. See the end of the full text for details.

Vertical integration increases opportunities for patient flow.

PubMed

Radoccia, R A; Benvenuto, J A; Blancett, L

1991-08-01

New sources of patients will become more and more important in the next decade as hospitals continue to feel the squeeze of a competitive marketplace. Vertical integration, a distribution tool used in other industries, will be a significant tool for health care administrators. In the following article, the authors explain the vertical integration model that shows promise for other institutions.

Modeling the CAPTEX Vertical Tracer Concentration Profiles.

NASA Astrophysics Data System (ADS)

Draxler, Roland R.; Stunder, Barbara J. B.

1988-05-01

Perfluorocarbon tracer concentration profiles measured by aircraft 600-900 km downwind of the release locations during CAPTEX are discussed and compared with some model results. In general, the concentrations decreased with height in the upper half of the boundary layer where the aircraft measurements were made. The results of a model sensitivity study suggested that the shape of the profile was primarily due to winds increasing with height and relative position of the sampling with respect to the upwind and downwind edge of the plume. Further modeling studies showed that relatively simple vertical mixing parameterizations could account for the complex vertical plume structure when the model had sufficient vertical resolution. In general, the model performed better with slower winds and corresponding longer transport times.

Vertical vibration analysis for elevator compensating sheave

NASA Astrophysics Data System (ADS)

Watanabe, Seiji; Okawa, Takeya; Nakazawa, Daisuke; Fukui, Daiki

2013-07-01

Most elevators applied to tall buildings include compensating ropes to satisfy the balanced rope tension between the car and the counter weight. The compensating ropes receive tension by the compensating sheave, which is installed at the bottom space of the elevator shaft. The compensating sheave is only suspended by the compensating ropes, therefore, the sheave can move vertically while the car is traveling. This paper shows the elevator dynamic model to evaluate the vertical motion of the compensating sheave. Especially, behavior in emergency cases, such as brake activation and buffer strike, was investigated to evaluate the maximum upward motion of the sheave. The simulation results were validated by experiments and the most influenced factor for the sheave vertical motion was clarified.

Steerable vertical to horizontal energy transducer for mobile robots

DOEpatents

Spletzer, Barry L.; Fischer, Gary J.; Feddema, John T.

2001-01-01

The present invention provides a steerable vertical to horizontal energy transducer for mobile robots that less complex and requires less power than two degree of freedom tilt mechanisms. The present invention comprises an end effector that, when mounted with a hopping actuator, translates along axis (typically vertical) actuation into combined vertical and horizontal motion. The end effector, or foot, mounts with an end of the actuator that moves toward the support surface (typically a floor or the earth). The foot is shaped so that the first contact with the support surface is off the axis of the actuator. Off-axis contact with the support surface generates an on-axis force (typically resulting in vertical motion) and a moment orthogonal to the axis. The moment initiates a horizontal tumbling motion, and tilts the actuator so that its axis is oriented with a horizontal component and continued actuation generates both vertical and horizontal force.

Influence of gravity on cat vertical vestibulo-ocular reflex

NASA Technical Reports Server (NTRS)

Tomko, D. L.; Wall, C., III; Robinson, F. R.; Staab, J. P.

1988-01-01

The vertical vestibulo-ocular reflex (VOR) was recorded in cats using electro-oculography during sinusoidal angular pitch. Peak stimulus velocity was 50 deg/s over a frequency range from 0.01 to 4.0 Hz. To test the effect of gravity on the vertical VOR, the animal was pitched while sitting upright or lying on its side. Upright pitch changed the cat's orientation relative to gravity, while on-side pitch did not. The cumulative slow component position of the eye during on-side pitch was less symmetric than during upright pitch. Over the mid-frequency range (0.1 to 1.0 Hz), the average gain of the vertical VOR was 14.5 percent higher during upright pitch than during on-side pitch. At low frequencies (less than 0.05 Hz) changing head position relative to gravity raised the vertical VOR gain and kept the reflex in phase with stimulus velocity. These results indicate that gravity-sensitive mechanisms make the vertical VOR more compensatory.

Contribution of the six major gait determinants on the vertical center of mass trajectory and the vertical ground reaction force.

PubMed

Hayot, C; Sakka, S; Lacouture, P

2013-04-01

Saunders et al. (1953) stated that the introduction of six gait determinants (pelvic rotation, pelvic obliquity, stance knee flexion, foot and ankle mechanisms, and tibiofemoral angle) to a compass gait model (two rigid legs hinged at the hips) provides an accurate simulation of the actual trajectory of the whole body center of mass (CoM). Their respective actions could also explain the shape of the vertical ground reaction force (GRF) pattern. Saunders' approach is considered as a kinematic description of some features of gait and is subject to debate. The purpose of this study is to realize a rigorous mechanical evaluation of the gait determinants theory using an appropriated mathematical model in which specific experimental data of gait trials are introduced. We first simulate a compass-like CoM trajectory using the proposed 3D mathematical model. Then, factorizing the model to introduce successively the kinematic data related to each gait determinant, we assess their respective contribution to both the CoM trajectory and the pattern of vertical GRF at different gait speeds. The results show that the stance knee flexion significatively decreases the estimated position of the CoM during midstance. Stance knee extension and pelvic obliquity contribute to the appearance of the pattern of vertical GRF during stance. The stance ankle dorsiflexion significatively contributes to CoM vertical excursion and the ankle plantarflexion contributes to the vertical GRF during terminal stance. The largest contribution towards the minimization of the CoM vertical amplitude during the complete gait step appears when considering the foot mechanisms and the pelvic obliquity in the proposed model. Copyright © 2012 Elsevier B.V. All rights reserved.

47 CFR 73.160 - Vertical plane radiation characteristics, f(θ).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 47 Telecommunication 4 2010-10-01 2010-10-01 false Vertical plane radiation characteristics, f(Î... SERVICES RADIO BROADCAST SERVICES AM Broadcast Stations § 73.160 Vertical plane radiation characteristics, f(θ). (a) The vertical plane radiation characteristics show the relative field being radiated at a...

Method for laser-based two-dimensional navigation system in a structured environment

DOEpatents

Boultinghouse, Karlan D.; Schoeneman, J. Lee; Tise, Bertice L.

1989-01-01

A low power, narrow laser beam, generated by a laser carried by a mobile vehicle, is rotated about a vertical reference axis as the vehicle navigates within a structured environment. At least three stationary retroreflector elements are located at known positions, preferably at the periphery of the structured environment, with one of the elements having a distinctive retroreflection. The projected rotating beam traverses each retroreflector in succession, and the corresponding retroreflections are received at the vehicle and focussed on a photoelectric cell to generate corresponding electrical signals. The signal caused by the distinctive retroreflection serves as an angle-measurement datum. An angle encoder coupled to the apparatus rotating the projected laser beam provides the angular separation from this datum of the lines connecting the mobile reference axis to successive retroreflectors. This real-time angular data is utilized with the known locations of the retroreflectors to trigonometrically compute using three point resection, the exact real-time location of the mobile reference axis (hence the navigating vehicle) vis-a-vis the structured environment, e.g., in terms of two-dimensional Cartesian coordinates associated with the environment.

49 CFR 179.14 - Coupler vertical restraint system.

Code of Federal Regulations, 2010 CFR

2010-10-01

... mating coupler (or simulated coupler) having only frictional vertical force resistance at the mating interface; or a mating coupler (or simulated coupler) having the capabilities described in paragraph (a) of this section; (2) The testing apparatus shall simulate the vertical coupler performance at the mating...

Global Vertical Rates from VLBl

NASA Technical Reports Server (NTRS)

Ma, Chopo; MacMillan, D.; Petrov, L.

2003-01-01

The analysis of global VLBI observations provides vertical rates for 50 sites with formal errors less than 2 mm/yr and median formal error of 0.4 mm/yr. These sites are largely in Europe and North America with a few others in east Asia, Australia, South America and South Africa. The time interval of observations is up to 20 years. The error of the velocity reference frame is less than 0.5 mm/yr, but results from several sites with observations from more than one antenna suggest that the estimated vertical rates may have temporal variations or non-geophysical components. Comparisons with GPS rates and corresponding site position time series will be discussed.

Language and Communication Datum.

ERIC Educational Resources Information Center

Sullivan, William J.

1989-01-01

Argues that communication is the primary function of language and that the signification function can be derived from it. Several theories of language are considered for their attitude toward the communication function. (26 references) (Author/VWL)

Bipedicle Vertical Mammoplasty Associated with Liposuction/Lipotunnelization.

PubMed

Maia, Manuel; Pinto, Cristina

2017-06-01

Vertical techniques have become more popular and versatile in breast reduction and mastopexy procedures. The authors introduce a combination of vertical mammoplasty with vertical bipedicle technique, presenting some innovations concerning pedicle design, glandular dissection pattern, and the role of liposuction. In this article, we describe a personal surgical technique and analyze the results on 73 mastopexy and breast reduction patients, operated on between 2012 and 2014 by the senior author. The most important aspects of this technique are as follows: 1. the concept of lipotunnelization, where parenchymal tunnels are made with cannulas without suction; 2. the systematic use of liposuction/lipotunnelization to recreate the inframammary fold and decrease pillars height; 3. the use of a thick and narrow vertical pedicle (bipedicled); 4. no skin undermining. Twenty-five patients underwent mastopexy and 48 breast reduction. Results were evaluated by clinical examination and patient photographs. Good shape and projection of the breast and correct nipple elevation were achieved, correlating with a high level of patient satisfaction. No major complications occurred. This lipomammoplasty technique is a reliable and effective option, suitable for a wide range of symptomatic macromastia/ptosis. Adjunctive use of liposuction/lipotunnelization in vertical breast reduction accomplishes effective contouring of the breast with low associated complications and significantly reduces the revision rates. This journal requires that authors assign a level of evidence to each article. For a full description of these evidence-based medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Intercomparison of vertical structure of storms revealed by ground-based (NMQ) and spaceborne radars (CloudSat-CPR and TRMM-PR).

PubMed

Fall, Veronica M; Cao, Qing; Hong, Yang

2013-01-01

Spaceborne radars provide great opportunities to investigate the vertical structure of clouds and precipitation. Two typical spaceborne radars for such a study are the W-band Cloud Profiling Radar (CPR) and Ku-band Precipitation Radar (PR), which are onboard NASA's CloudSat and TRMM satellites, respectively. Compared to S-band ground-based radars, they have distinct scattering characteristics for different hydrometeors in clouds and precipitation. The combination of spaceborne and ground-based radar observations can help in the identification of hydrometeors and improve the radar-based quantitative precipitation estimation (QPE). This study analyzes the vertical structure of the 18 January, 2009 storm using data from the CloudSat CPR, TRMM PR, and a NEXRAD-based National Mosaic and Multisensor QPE (NMQ) system. Microphysics above, within, and below the melting layer are studied through an intercomparison of multifrequency measurements. Hydrometeors' type and their radar scattering characteristics are analyzed. Additionally, the study of the vertical profile of reflectivity (VPR) reveals the brightband properties in the cold-season precipitation and its effect on the radar-based QPE. In all, the joint analysis of spaceborne and ground-based radar data increases the understanding of the vertical structure of storm systems and provides a good insight into the microphysical modeling for weather forecasts.

Intercomparison of Vertical Structure of Storms Revealed by Ground-Based (NMQ) and Spaceborne Radars (CloudSat-CPR and TRMM-PR)

PubMed Central

Fall, Veronica M.; Hong, Yang

2013-01-01

Spaceborne radars provide great opportunities to investigate the vertical structure of clouds and precipitation. Two typical spaceborne radars for such a study are the W-band Cloud Profiling Radar (CPR) and Ku-band Precipitation Radar (PR), which are onboard NASA's CloudSat and TRMM satellites, respectively. Compared to S-band ground-based radars, they have distinct scattering characteristics for different hydrometeors in clouds and precipitation. The combination of spaceborne and ground-based radar observations can help in the identification of hydrometeors and improve the radar-based quantitative precipitation estimation (QPE). This study analyzes the vertical structure of the 18 January, 2009 storm using data from the CloudSat CPR, TRMM PR, and a NEXRAD-based National Mosaic and Multisensor QPE (NMQ) system. Microphysics above, within, and below the melting layer are studied through an intercomparison of multifrequency measurements. Hydrometeors' type and their radar scattering characteristics are analyzed. Additionally, the study of the vertical profile of reflectivity (VPR) reveals the brightband properties in the cold-season precipitation and its effect on the radar-based QPE. In all, the joint analysis of spaceborne and ground-based radar data increases the understanding of the vertical structure of storm systems and provides a good insight into the microphysical modeling for weather forecasts. PMID:24459424

Mechanical design of NASA Ames Research Center vertical motion simulator

NASA Technical Reports Server (NTRS)

Engelbert, D. F.; Bakke, A. P.; Chargin, M. K.; Vallotton, W. C.

1976-01-01

NASA has designed and is constructing a new flight simulator with large vertical travel. Several aspects of the mechanical design of this Vertical Motion Simulator (VMS) are discussed, including the multiple rack and pinion vertical drive, a pneumatic equilibration system, and the friction-damped rigid link catenaries used as cable supports.

Effect of vertical integration on the utilization of hardwood resources

Treesearch

Jan Wiedenbeck

2002-01-01

The effectiveness of vertical integration in promoting the efficient utilization of the hardwood resource in the eastern United States was assessed during a series of interviews with vertically integrated hardwood manufacturers in the Appalachian region. Data from 19 companies that responded to the 1996 phone survey indicate that: 1) vertically integrated hardwood...

Upstairs downstairs: vertical integration of a pediatric service.

PubMed

Racine, A D; Stein, R E; Belamarich, P F; Levine, E; Okun, A; Porder, K; Rosenfeld, J L; Schechter, M

1998-07-01

The combined effects of recent changes in health care financing and training priorities have compelled academic medical centers to develop innovative structures to maintain service commitments yet conform to health care marketplace demands. In 1992, a municipal hospital in the Bronx, New York, affiliated with a major academic medical center reorganized its pediatric service into a vertically integrated system of four interdependent practice teams that provided comprehensive care in the ambulatory as well as inpatient settings. One of the goals of the new system was to conserve inpatient resources. To describe the development of a new vertically integrated pediatric service at an inner-city municipal hospital and to test whether its adoption was associated with the use of fewer inpatient resources. A descriptive analysis of the rationale, goals, implementation strategies, and structure of the vertically integrated pediatric service combined with a before-and-after comparison of in-hospital resource consumption. A before-and-after comparison was conducted for two periods: the period before vertical integration, from January 1989 to December 1991, and the period after the adoption of vertical integration, from July 1992 to December 1994. Four measures of inpatient resource use were compared after adjustment for case mix index: mean certified length of stay per case, mean number of radiologic tests per case, mean number of ancillary tests per case, and mean number of laboratory tests per case. Difference-in-differences-in-differences estimators were used to control for institution-wide trends throughout the time period and regional trends in inpatient pediatric practice occurring across institutions. Results. In 1992, the Department of Pediatrics at the Albert Einstein College of Medicine reorganized the pediatric service at Jacobi Medical Center, one of its principal municipal hospital affiliates, into a vertically integrated pediatric service that combines ambulatory

Comparing the role of absolute sea-level rise and vertical tectonic motions in coastal flooding, Torres Islands (Vanuatu)

NASA Astrophysics Data System (ADS)

Ballu, Valérie; Bouin, Marie-Noëlle; Siméoni, Patricia; Crawford, Wayne C.; Calmant, Stephane; Boré, Jean-Michel; Kanas, Tony; Pelletier, Bernard

2011-08-01

Since the late 1990s, rising sea levels around the Torres Islands (north Vanuatu, southwest Pacific) have caused strong local and international concern. In 2002-2004, a village was displaced due to increasing sea incursions, and in 2005 a United Nations Environment Programme press release referred to the displaced village as perhaps the world's first climate change "refugees." We show here that vertical motions of the Torres Islands themselves dominate the apparent sea-level rise observed on the islands. From 1997 to 2009, the absolute sea level rose by 150 + /-20 mm. But GPS data reveal that the islands subsided by 117 + /-30 mm over the same time period, almost doubling the apparent gradual sea-level rise. Moreover, large earthquakes that occurred just before and after this period caused several hundreds of mm of sudden vertical motion, generating larger apparent sea-level changes than those observed during the entire intervening period. Our results show that vertical ground motions must be accounted for when evaluating sea-level change hazards in active tectonic regions. These data are needed to help communities and governments understand environmental changes and make the best decisions for their future.

Comparing the role of absolute sea-level rise and vertical tectonic motions in coastal flooding, Torres Islands (Vanuatu).

PubMed

Ballu, Valérie; Bouin, Marie-Noëlle; Siméoni, Patricia; Crawford, Wayne C; Calmant, Stephane; Boré, Jean-Michel; Kanas, Tony; Pelletier, Bernard

2011-08-09

Since the late 1990s, rising sea levels around the Torres Islands (north Vanuatu, southwest Pacific) have caused strong local and international concern. In 2002-2004, a village was displaced due to increasing sea incursions, and in 2005 a United Nations Environment Programme press release referred to the displaced village as perhaps the world's first climate change "refugees." We show here that vertical motions of the Torres Islands themselves dominate the apparent sea-level rise observed on the islands. From 1997 to 2009, the absolute sea level rose by 150 + /-20 mm. But GPS data reveal that the islands subsided by 117 + /-30 mm over the same time period, almost doubling the apparent gradual sea-level rise. Moreover, large earthquakes that occurred just before and after this period caused several hundreds of mm of sudden vertical motion, generating larger apparent sea-level changes than those observed during the entire intervening period. Our results show that vertical ground motions must be accounted for when evaluating sea-level change hazards in active tectonic regions. These data are needed to help communities and governments understand environmental changes and make the best decisions for their future.

RSRA vertical drag test report. [rotor systems research aircraft

NASA Technical Reports Server (NTRS)

Flemming, R. J.

1981-01-01

The Rotor Systems Research Aircraft (RSRA), because of its ability to measure rotor loads, was used to conduct an experiment to determine vertical drag, tail rotor blockage, and thrust augmentation as affected by ground clearance and flight velocity. The RSRA was flown in the helicopter configuration at speeds from 0 to 15 knots for wheel heights from 5 to 150 feet, and to 60 knots out of ground effect. The vertical drag trends in hover, predicted by theory and shown in model tests, were generally confirmed. The OGE hover vertical drag is 4.0 percent, 1.1 percent greater than predicted. The vertical drag decreases rapidly as wheel height is reduced, and is zero at a wheel height of 6 feet. The vertical drag also decreases with forward speed, approaching zero at sixty knots. The test data show the effect of wheel height and forward speed on thrust, gross weight capability, and power, and provide the relationships for power and collective pitch at constant gross weight required for the simulation of helicopter takeoffs and landings.

Study of Gravity Effects on Titanium Laser Welding in the Vertical Position

PubMed Central

Yuan, Zhang; Pu, Haitao; Li, Haigang; Cheng, Hao; Du, Dong; Shan, Jiguo

2017-01-01

To obtain satisfactory welds in positional laser beam welding, it is necessary to know how process parameters will influence the quality of welds in different welding positions. In this study, the titanium alloy Ti6Al4V sheets were laser welded in two vertical welding positions (vertical up and vertical down), and the appearance, porosity, strength, and ductility of the laser joints were evaluated. Results show that undercuts of the vertical up welds were greater than that of vertical down welds, while the porosity contents were much higher in vertical down welds than that in vertical up welds. When welding with a higher heat input, the vertical up welding position resulted in poor weld profiles (undercuts and burn-through holes), whereas the vertical down welding position led to excessive porosity contents in welds. Both severe undercut and excessive porosity were detrimental to the tensile properties of the welds. Weld appearance was improved and porosity contents were reduced by using a lower heat input, achieving better weld quality. Therefore, it is suggested that process parameter settings with relatively high laser powers and welding speeds, which can result in lower heat inputs, are used when laser welding the Ti6Al4V titanium alloys vertically. PMID:28885573

Study of Gravity Effects on Titanium Laser Welding in the Vertical Position.

PubMed

Chang, Baohua; Yuan, Zhang; Pu, Haitao; Li, Haigang; Cheng, Hao; Du, Dong; Shan, Jiguo

2017-09-08

To obtain satisfactory welds in positional laser beam welding, it is necessary to know how process parameters will influence the quality of welds in different welding positions. In this study, the titanium alloy Ti6Al4V sheets were laser welded in two vertical welding positions (vertical up and vertical down), and the appearance, porosity, strength, and ductility of the laser joints were evaluated. Results show that undercuts of the vertical up welds were greater than that of vertical down welds, while the porosity contents were much higher in vertical down welds than that in vertical up welds. When welding with a higher heat input, the vertical up welding position resulted in poor weld profiles (undercuts and burn-through holes), whereas the vertical down welding position led to excessive porosity contents in welds. Both severe undercut and excessive porosity were detrimental to the tensile properties of the welds. Weld appearance was improved and porosity contents were reduced by using a lower heat input, achieving better weld quality. Therefore, it is suggested that process parameter settings with relatively high laser powers and welding speeds, which can result in lower heat inputs, are used when laser welding the Ti6Al4V titanium alloys vertically.

Interdisciplinary Social Science: An Example of Vertical and Horizontal Integrative Strategies

NASA Astrophysics Data System (ADS)

Durlabhji, Subhash

2005-03-01

A "Concept-Centered" strategy for Integrative Studies was proposed and implemented in the creation of the book Power in Focus: Perspectives from Multiple Disciplines. Essays on the ubiquitous concept of Power were solicited internationally and a final cut of ten essays from ten different disciplines, written specifically for this project, were included. This provides an example of what might be called Horizontal Integration, as it cut across multiple disciplines. One of the essays in the volume provides an example of Vertical Integration, as it applies a psychodynamic hypothesis concerning the development of Power relations among humans across hierarchical levels, from the child to the family to other groups and institutions in society, including finally entire nations and regions of the world.

Going Up? The Pros and Cons of Vertical Expansion.

ERIC Educational Resources Information Center

Myler, Patricia A.; Boggs, Richard C.

2002-01-01

Describes the advantages and disadvantages of the vertical expansion of school buildings. Considers such factors as fire protection, compliance with the Americans with Disabilities Act, and cost. Discusses alternatives to vertical expansion. (PKP)

Lunar vertical-shaft mining system

NASA Technical Reports Server (NTRS)

Introne, Steven D. (Editor); Krause, Roy; Williams, Erik; Baskette, Keith; Martich, Frederick; Weaver, Brad; Meve, Jeff; Alexander, Kyle; Dailey, Ron; White, Matt

1994-01-01

This report proposes a method that will allow lunar vertical-shaft mining. Lunar mining allows the exploitation of mineral resources imbedded within the surface. The proposed lunar vertical-shaft mining system is comprised of five subsystems: structure, materials handling, drilling, mining, and planning. The structure provides support for the exploration and mining equipment in the lunar environment. The materials handling subsystem moves mined material outside the structure and mining and drilling equipment inside the structure. The drilling process bores into the surface for the purpose of collecting soil samples, inserting transducer probes, or locating ore deposits. Once the ore deposits are discovered and pinpointed, mining operations bring the ore to the surface. The final subsystem is planning, which involves the construction of the mining structure.

Shallow 3-D vertical seismic profiling around a contaminant withdrawal well on the Lawrence Livermore National Laboratory Site

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rector, J.; Bainer, R.; Milligan, P.

1997-01-30

One of the major problems associated with ground water contaminant remediation is well placement. Optimal-placement of wells requires an accurate knowledge of geologic structure and stratigraphy in the near surface sediments and rock (0 to 100 m). Without the development of remote imaging provided by geophysical techniques, the required spacing between treatment wells may be less than 2 m in order to be confident that all contaminant reservoirs had been remediated. One method for characterizing geologic structure and stratigraphy in the near surface is vertical seismic profiling (VSP), a technique often used on deep exploration wells to calibrate surface seismicmore » reflection data. For near-surface applications, VSP data can be acquired efficiently using an array of hydrophones lowered into a fluid-filled borehole (Milligan et al, 1997). In this paper we discuss the acquisition and processing of a 3-D VSP collected at a shallow remediation site located on the grounds of the Lawrence Livermore National Laboratory (LLNL) near Livermore, California. The site was used by the United States Navy as an air training base. At this time, initial releases of hazardous materials to the environment occurred in the form of solvents [volatile organic compounds (VOCs)] that were used for the cleaning of airplanes and their parts. Gasoline, diesel and other petroleum-based compounds are also known to have leaked into the ground. California Research and Development Company, a subsidy of Standard Oil, occupied the southeastern portion of the site from 1950 to 1954. The first releases of radioactive materials to the environment occurred at this time, with the beginning of testing of radioactive materials at the site. In 1952, LLNL acquired the site. Additional releases of VOCS, polychlorinated biphenyls (PCBs), metals, radionuclides (primarily tritium), gasoline and pesticides have occurred since. These releases were due to localized spills, landfills, surface impoundments

Vertically-integrated Approaches for Carbon Sequestration Modeling

NASA Astrophysics Data System (ADS)

Bandilla, K.; Celia, M. A.; Guo, B.

2015-12-01

Carbon capture and sequestration (CCS) is being considered as an approach to mitigate anthropogenic CO2 emissions from large stationary sources such as coal fired power plants and natural gas processing plants. Computer modeling is an essential tool for site design and operational planning as it allows prediction of the pressure response as well as the migration of both CO2 and brine in the subsurface. Many processes, such as buoyancy, hysteresis, geomechanics and geochemistry, can have important impacts on the system. While all of the processes can be taken into account simultaneously, the resulting models are computationally very expensive and require large numbers of parameters which are often uncertain or unknown. In many cases of practical interest, the computational and data requirements can be reduced by choosing a smaller domain and/or by neglecting or simplifying certain processes. This leads to a series of models with different complexity, ranging from coupled multi-physics, multi-phase three-dimensional models to semi-analytical single-phase models. Under certain conditions the three-dimensional equations can be integrated in the vertical direction, leading to a suite of two-dimensional multi-phase models, termed vertically-integrated models. These models are either solved numerically or simplified further (e.g., assumption of vertical equilibrium) to allow analytical or semi-analytical solutions. This presentation focuses on how different vertically-integrated models have been applied to the simulation of CO2 and brine migration during CCS projects. Several example sites, such as the Illinois Basin and the Wabamun Lake region of the Alberta Basin, are discussed to show how vertically-integrated models can be used to gain understanding of CCS operations.

Thermally driven film climbing a vertical cylinder

NASA Astrophysics Data System (ADS)

Smolka, Linda

2017-11-01

The dynamics of a Marangoni driven film climbing the outside of a vertical cylinder is examined in numerical simulations of a thin film model. The model has three parameters: the scaled cylinder radius R̂, upstream film height h∞ and downstream precursor film thickness b , and reduces to the model for Marangoni driven film climbing a vertical plate when R̂ -> ∞ . The advancing front displays dynamics similar to that along a vertical plate where, depending on h∞ , the film forms a Lax shock, an undercompressive double shock or a rarefaction-undercompressive shock. A linear stability analysis of the Lax shock reveals the number of fingers that form along the contact line increases linearly with cylinder circumference while no fingers form below R̂ 1.15 with b = 0.1 . The substrate curvature controls the Lax shock height, bounds on h∞ that define the three solutions and the maximum growth rate of perturbations when R̂ = O (1) , whereas the shape of solutions and the stability of the Lax shock converge to the behavior on a vertical plate when R̂ >= O (10) . The azimuthal curvatures of the base state and perturbation, arising from the annular geometry of the film, promote instability of the advancing contact line.

Vertical motions in the equatorial middle atmosphere

NASA Technical Reports Server (NTRS)

Weisman, M. L.

1979-01-01

A single station vertical velocity equation which considers ageostrophic and diabatic effects derived from the first law of thermodynamics and a generalized thermal wind relation is presented. An analysis and verification procedure which accounts for measurement and calculation errors as well as time and space continuity arguments and theoretical predictions are described. Vertical velocities are calculated at every kilometer between 25 and 60 km and for approximately every three hours for the above diurnal period at Kourou (French Guiana), Fort Sherman (Panama Canal Zone), Ascension Island, Antigua (British West Indies) and Natal (Brazil). The results, plotted as time series cross sections, suggest vertical motions ranging in magnitude from 1 or 2 cm/sec at 30 km to as much as 15 cm/sec at 60 km. Many of the general features of the results agree well with atmospheric tidal predictions but many particular features suggest that both smaller time scale gravity waves (periods less than 6 hours) and synoptic type waves (periods greater than 1 day) may be interacting significantly with the tidal fields. The results suggest that vertical motions can be calculated for the equatorial middle atmosphere and must be considered a significant part of the motion for time scales from 8 to 24 hours.

Integrative Curriculum Development in Nuclear Education and Research Vertical Enhancement Program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Egarievwe, Stephen U.; Jow, Julius O.; Edwards, Matthew E.

Using a vertical education enhancement model, a Nuclear Education and Research Vertical Enhancement (NERVE) program was developed. The NERVE program is aimed at developing nuclear engineering education and research to 1) enhance skilled workforce development in disciplines relevant to nuclear power, national security and medical physics, and 2) increase the number of students and faculty from underrepresented groups (women and minorities) in fields related to the nuclear industry. The program uses multi-track training activities that vertically cut across the several education domains: undergraduate degree programs, graduate schools, and post-doctoral training. In this paper, we present the results of an integrativemore » curriculum development in the NERVE program. The curriculum development began with nuclear content infusion into existing science, engineering and technology courses. The second step involved the development of nuclear engineering courses: 1) Introduction to Nuclear Engineering, 2) Nuclear Engineering I, and 2) Nuclear Engineering II. The third step is the establishment of nuclear engineering concentrations in two engineering degree programs: 1) electrical engineering, and 2) mechanical engineering. A major outcome of the NERVE program is a collaborative infrastructure that uses laboratory work, internships at nuclear facilities, on-campus research, and mentoring in collaboration with industry and government partners to provide hands-on training for students. The major activities of the research and education collaborations include: - One-week spring training workshop at Brookhaven National Laboratory: The one-week training and workshop is used to enhance research collaborations and train faculty and students on user facilities/equipment at Brookhaven National Laboratory, and for summer research internships. Participants included students, faculty members at Alabama A and M University and research collaborators at BNL. The activities include 1

ostglacial rebound from VLBI Geodesy: On Establishing Vertical Reference

NASA Technical Reports Server (NTRS)

Argus, Donald .

1996-01-01

I propose that a useful reference frame for vertical motions is that found by minimizing differences between vertical motions observed with VLBI [Ma and Ryan, 1995] and predictions from postglacial rebound predictions [Peltier, 1995].

Summary of extensometric measurements in El Paso, Texas

USGS Publications Warehouse

Heywood, Charles E.

2003-01-01

Two counter-weighted-pipe borehole extensometers were installed on the left bank of the Rio Grande between El Paso, Texas, and Ciudad Juarez, Chihuahua, Mexico, in 1992. A shallow extensometer measures vertical compaction in the 6- to 100-meter aquifer-system depth interval. A deep extensometer measures vertical compaction in the 6- to 305-meter aquifer-system depth interval. Both extensometers are referenced to the same surface datum, which allows time-series differencing to determine vertical compaction in the depth interval between 100 and 305 meters. From April 2, 1993, through June 13, 2002, 1.6 centimeters of compaction occurred in the 6-to 305-m depth interval. Until February 1999, most aquifer-system compaction occurred in the deeper aquifer-system interval between 100 and 305 meters, from which ground water was extracted. After that time, compaction in the shallow interval from 6 to 100 meters was predominant and attained a maximum of 7.6 millimeters by June 13, 2002. Minor residual compaction is expected to continue; continued maintenance of the El Paso extensometers would document this process.

Radially Magnetized Protoplanetary Disk: Vertical Profile

NASA Astrophysics Data System (ADS)

Russo, Matthew; Thompson, Christopher

2015-11-01

This paper studies the response of a thin accretion disk to an external radial magnetic field. Our focus is on protoplanetary disks (PPDs), which are exposed during their later evolution to an intense, magnetized wind from the central star. A radial magnetic field is mixed into a thin surface layer, wound up by the disk shear, and pushed downward by a combination of turbulent mixing and ambipolar and ohmic drift. The toroidal field reaches much greater strengths than the seed vertical field that is usually invoked in PPD models, even becoming superthermal. Linear stability analysis indicates that the disk experiences the magnetorotational instability (MRI) at a higher magnetization than a vertically magnetized disk when both the effects of ambipolar and Hall drift are taken into account. Steady vertical profiles of density and magnetic field are obtained at several radii between 0.06 and 1 AU in response to a wind magnetic field Br ˜ (10-4-10-2)(r/ AU)-2 G. Careful attention is given to the radial and vertical ionization structure resulting from irradiation by stellar X-rays. The disk is more strongly magnetized closer to the star, where it can support a higher rate of mass transfer. As a result, the inner ˜1 AU of a PPD is found to evolve toward lower surface density. Mass transfer rates around 10-8 M⊙ yr-1 are obtained under conservative assumptions about the MRI-generated stress. The evolution of the disk and the implications for planet migration are investigated in the accompanying paper.

On vertical profile of ozone at Syowa

NASA Technical Reports Server (NTRS)

Chubachi, Shigeru

1994-01-01

The difference in the vertical ozone profile at Syowa between 1966-1981 and 1982-1988 is shown. The month-height cross section of the slope of the linear regressions between ozone partial pressure and 100-mb temperature is also shown. The vertically integrated values of the slopes are in close agreement with the slopes calculated by linear regression of Dobson total ozone on 100-mb temperature in the period of 1982-1988.

Causes of the longitudinal differences in the equatorial vertical E × B drift during the 2013 SSW period as simulated by the TIME-GCM

NASA Astrophysics Data System (ADS)

Maute, A.; Hagan, M. E.; Yudin, V.; Liu, H.-L.; Yizengaw, E.

2015-06-01

During stratospheric sudden warming (SSW) periods large changes in the low-latitude vertical drift have been observed at Jicamarca as well as in other longitudinal sectors. In general, a strengthening of the daytime maximum vertical drift with a shift from prenoon to the afternoon is observed. During the January 2013 stratospheric warming significant longitudinal differences in the equatorial vertical drift were observed. At Jicamarca the previously reported SSW behavior prevails; however, no shift of the daytime maximum drift was exhibited in the African sector. Using the National Center for Atmospheric Research thermosphere-ionosphere-mesosphere electrodynamics general circulation model (TIME-GCM) the possible causes for the longitudinal difference are examined. The timing of the strong SSW effect in the vertical drift (15-20 January) coincides with moderate geomagnetic activity. The simulation indicates that approximately half of the daytime vertical drift increase in the American sector may be related to the moderate geophysical conditions (Kp = 4) with the effect being negligible in the African sector. The simulation suggests that the wind dynamo accounts for approximately 50% of the daytime vertical drift in the American sector and almost 100% in the African sector. The simulation agrees with previous findings that the migrating solar tides and the semidiurnal westward propagating tide with zonal wave number 1 (SW1) mainly contribute to the daytime wind dynamo and vertical drift. Numerical experiments suggest that the neutral wind and the geomagnetic main field contribute to the presence (absence) of a local time shift in the daytime maximum drift in the American (African) sector.

Apparatus and method for detecting flaws in conductive material

DOEpatents

Hockey, Ronald L.; Riechers, Douglas M.

1999-01-01

The present invention is an improved sensing unit for detecting flaws in conductive material wherein the sensing coil is positioned away from a datum of either the datum point, the datum orientation, or a combination thereof. Position of the sensing coil away from a datum increases sensitivity for detecting flaws having a characteristic volume less than about 1 mm.sup.3, and further permits detection of subsurface flaws. Use of multiple sensing coils permits quantification of flaw area or volume.

Half-State Readout In Vertical-Bloch-Line Memory

NASA Technical Reports Server (NTRS)

Katti, Romney R.; Wu, Jiin-Chuan; Stadler, Henry L.

1994-01-01

Potentially narrow margins of chirality-based chopping of magnetic stripes avoided. Half-state readout is experimental method of readout in Vertical-Bloch-Line (VBL) memory. Based on differential deflections of magnetic stripe domains in which data bits stored. To give meaning to explanation of half-state readout, see "Vertical-Bloch-Line Memory" (NPO-18467).

Flood-inundation maps for Lake Champlain in Vermont and in northern Clinton County, New York

USGS Publications Warehouse

Flynn, Robert H.; Hayes, Laura

2016-06-30

Digital flood-inundation maps for an approximately100-mile length of Lake Champlain in Addison, Chittenden, Franklin, and Grand Isle Counties in Vermont and northern Clinton County in New York were created by the U.S. Geological Survey (USGS) in cooperation with the International Joint Commission (IJC). The flood-inundationmaps, which can be accessed through the International Joint Commission (IJC) Web site at http://www.ijc.org/en_/, depict estimates of the areal extent flooding correspondingto selected water levels (stages) at the USGS lake gage on the Richelieu River (Lake Champlain) at Rouses Point, N.Y. (station number 04295000). In this study, wind and seiche effects (standing oscillating wave with a long wavelength) were not taken into account and the flood-inundation mapsreflect 11 stages (elevations) for Lake Champlain that are static for the study length of the lake. Near-real-time stages at this lake gage, and others on Lake Champlain, may be obtained on the Internet from the USGS National Water Information System at http://waterdata.usgs.gov/ or the National Weather Service Advanced Hydrologic Prediction Service at http:/water.weather.gov/ahps/, which also forecasts flood hydrographs at the Richelieu River (Lake Champlain) at Rouses Point.Static flood boundary extents were determined for LakeChamplain in Addison, Chittenden, Franklin, and Grand Isle Counties in Vermont and northern Clinton County in New York using recently acquired (2013–2014) lidar (light detection and ranging) and may be referenced to any of the five USGS lake gages on Lake Champlain. Of these five lakgages, USGS lake gage 04295000, Richelieu River (Lake Champlain) at Rouses Point, N.Y., is the only USGS lake gage that is also a National Weather Service prediction location. Flood boundary extents for the Lake Champlain static flood-inundation map corresponding to the May 201 flood(103.2 feet [ft], National Geodetic Vertical Datum [NGVD] 29) were evaluated by comparing these boundary

Heat and momentum transport scalings in vertical convection

NASA Astrophysics Data System (ADS)

Shishkina, Olga

2016-11-01

For vertical convection, where a fluid is confined between two differently heated isothermal vertical walls, we investigate the heat and momentum transport, which are measured, respectively, by the Nusselt number Nu and the Reynolds number Re . For laminar vertical convection we derive analytically the dependence of Re and Nu on the Rayleigh number Ra and the Prandtl number Pr from our boundary layer equations and find two different scaling regimes: Nu Pr 1 / 4 Ra 1 / 4 , Re Pr - 1 / 2 Ra 1 / 2 for Pr << 1 and Nu Pr0 Ra 1 / 4 , Re Pr-1 Ra 1 / 2 for Pr >> 1 . Direct numerical simulations for Ra from 105 to 1010 and Pr from 0.01 to 30 are in excellent ageement with our theoretical findings and show that the transition between the regimes takes place for Pr around 0.1. We summarize the results from and present new theoretical and numerical results for transitional and turbulent vertical convection. The work is supported by the Deutsche Forschungsgemeinschaft (DFG) under the Grant Sh 405/4 - Heisenberg fellowship.

Origami building blocks: Generic and special four-vertices

NASA Astrophysics Data System (ADS)

Waitukaitis, Scott; van Hecke, Martin

2016-02-01

Four rigid panels connected by hinges that meet at a point form a four-vertex, the fundamental building block of origami metamaterials. Most materials designed so far are based on the same four-vertex geometry, and little is known regarding how different geometries affect folding behavior. Here we systematically categorize and analyze the geometries and resulting folding motions of Euclidean four-vertices. Comparing the relative sizes of sector angles, we identify three types of generic vertices and two accompanying subtypes. We determine which folds can fully close and the possible mountain-valley assignments. Next, we consider what occurs when sector angles or sums thereof are set equal, which results in 16 special vertex types. One of these, flat-foldable vertices, has been studied extensively, but we show that a wide variety of qualitatively different folding motions exist for the other 15 special and 3 generic types. Our work establishes a straightforward set of rules for understanding the folding motion of both generic and special four-vertices and serves as a roadmap for designing origami metamaterials.

Origami building blocks: Generic and special four-vertices.

PubMed

Waitukaitis, Scott; van Hecke, Martin

2016-02-01

Four rigid panels connected by hinges that meet at a point form a four-vertex, the fundamental building block of origami metamaterials. Most materials designed so far are based on the same four-vertex geometry, and little is known regarding how different geometries affect folding behavior. Here we systematically categorize and analyze the geometries and resulting folding motions of Euclidean four-vertices. Comparing the relative sizes of sector angles, we identify three types of generic vertices and two accompanying subtypes. We determine which folds can fully close and the possible mountain-valley assignments. Next, we consider what occurs when sector angles or sums thereof are set equal, which results in 16 special vertex types. One of these, flat-foldable vertices, has been studied extensively, but we show that a wide variety of qualitatively different folding motions exist for the other 15 special and 3 generic types. Our work establishes a straightforward set of rules for understanding the folding motion of both generic and special four-vertices and serves as a roadmap for designing origami metamaterials.

Vertical tilts of tropospheric waves - Observations and theory

NASA Technical Reports Server (NTRS)

Ebisuzaki, Wesley

1991-01-01

Two methods are used to investigate the vertical tilts of planetary waves as functions of zonal wavenumber and frequency. The vertical tilts are computed by cross-spectral analysis of the geopotential heights at different pressures. In the midlatitude troposphere, the eastward-moving waves had a westward tilt with height, as expected, but the westward-moving waves with frequencies higher than 0.2/d showed statistically significant eastward vertical tilts. For a free Rossby wave, this implies that the Eliassen-Palm flux is downward along with its energy propagation. A downward energy propagation suggests an upper-level source of these waves. It is proposed that the eastward-tilting waves were forced by the nonlinear interaction of stationary waves and baroclinically unstable cyclone-scale waves. The predicted vertical tilt and phase speed were consistent with the observations. In addition, simulations of a general circulation model were analyzed. In the control run, eastward-tilting waves disappeared when the sources of stationary waves were removed. This is consistent with the present theory.

Pelvic kinematic method for determining vertical jump height.

PubMed

Chiu, Loren Z F; Salem, George J

2010-11-01

Sacral marker and pelvis reconstruction methods have been proposed to approximate total body center of mass during relatively low intensity gait and hopping tasks, but not during a maximum effort vertical jumping task. In this study, center of mass displacement was calculated using the pelvic kinematic method and compared with center of mass displacement using the ground-reaction force-impulse method, in experienced athletes (n = 13) performing restricted countermovement vertical jumps. Maximal vertical jumps were performed in a biomechanics laboratory, with data collected using an 8-camera motion analysis system and two force platforms. The pelvis center of mass was reconstructed from retro-reflective markers placed on the pelvis. Jump height was determined from the peak height of the pelvis center of mass minus the standing height. Strong linear relationships were observed between the pelvic kinematic and impulse methods (R² = .86; p < .01). The pelvic kinematic method underestimated jump height versus the impulse method, however, the difference was small (CV = 4.34%). This investigation demonstrates concurrent validity for the pelvic kinematic method to determine vertical jump height.

ONLINE MINIMIZATION OF VERTICAL BEAM SIZES AT APS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Yipeng

In this paper, online minimization of vertical beam sizes along the APS (Advanced Photon Source) storage ring is presented. A genetic algorithm (GA) was developed and employed for the online optimization in the APS storage ring. A total of 59 families of skew quadrupole magnets were employed as knobs to adjust the coupling and the vertical dispersion in the APS storage ring. Starting from initially zero current skew quadrupoles, small vertical beam sizes along the APS storage ring were achieved in a short optimization time of one hour. The optimization results from this method are briefly compared with the onemore » from LOCO (Linear Optics from Closed Orbits) response matrix correction.« less

The effects of vertical motion on the performance of current meters

USGS Publications Warehouse

Thibodeaux, K.G.; Futrell, J. C.

1987-01-01

A series of tests to determine the correction coefficients for Price type AA and Price type OAA current meters, when subjected to vertical motion in a towing tank, have been conducted. During these tests, the meters were subjected to vertical travel that ranged from 1.0 to 4.0 ft and vertical rates of travel that ranged from 0.33 to 1.20 ft/sec while being towed through the water at speeds ranging from 0 to 8 ft/sec. The tests show that type AA and type OAA current meters are affected adversely by the rate of vertical motion and the distance of vertical travel. In addition, the tests indicate that when current meters are moved vertically, correction coefficients must be applied to the observed meter velocities to correct for the registration errors that are induced by the vertical motion. The type OAA current meter under-registers and the type AA current meter over-registers in observed meter velocity. These coefficients for the type OAA current meter range from 0.99 to 1.49 and for the type AA current meter range from 0.33 to 1.07. When making current meter measurements from a boat or a cableway, errors in observed current meter velocity will occur when the bobbing of a boat or cableway places the current meter into vertical motion. These errors will be significant when flowing water is < 2 ft/sec and the rate of vertical motion is > 0.3 ft/sec. (Author 's abstract)

Effect of gravity on vertical eye position.

PubMed

Pierrot-Deseilligny, C

2009-05-01

There is growing evidence that gravity markedly influences vertical eye position and movements. A new model for the organization of brainstem upgaze pathways is presented in this review. The crossing ventral tegmental tract (CVTT) could be the efferent tract of an "antigravitational" pathway terminating at the elevator muscle motoneurons in the third nerve nuclei and comprising, upstream, the superior vestibular nucleus and y-group, the flocculus, and the otoliths. This pathway functions in parallel to the medial longitudinal fasciculus pathways, which control vertical eye movements made to compensate for all vertical head movements and may also comprise the "gravitational" vestibular pathways, involved in the central reflection of the gravity effect. The CVTT could provide the upgaze system with the supplement of tonic activity required to counteract the gravity effect expressed in the gravitational pathway, being permanently modulated according to the static positions of the head (i.e., the instantaneous gravity vector) between a maximal activity in the upright position and a minimal activity in horizontal positions. Different types of arguments support this new model. The permanent influence of gravity on vertical eye position is strongly suggested by the vertical slow phases and nystagmus observed after rapid changes in hypo- or hypergravity. The chin-beating nystagmus, existing in normal subjects with their head in the upside-down position, suggests that gravity is not compensated for in the downgaze system. Upbeat nystagmus due to brainstem lesions, most likely affecting the CVTT circuitry, is improved when the head is in the horizontal position, suggesting that this circuitry is involved in the counteraction of gravity between the upright and horizontal positions of the head. In downbeat nystagmus due to floccular damage, in which a permanent hyperexcitation of the CVTT could exist, a marked influence of static positions of the head is also observed. Finally

Vertical integration of medical education: Riverland experience, South Australia.

PubMed

Rosenthal, D R; Worley, P S; Mugford, B; Stagg, P

2004-01-01

Vertical integration of medical education is currently a prominent international topic, resulting from recent strategic initiatives to improve medical education and service delivery in areas of poorly met medical need. In this article, vertical integration of medical education is defined as 'a grouping of curricular content and delivery mechanisms, traversing the traditional boundaries of undergraduate, postgraduate and continuing medical education, with the intent of enhancing the transfer of knowledge and skills between those involved in the learning-teaching process'. Educators closely involved with vertically integrated teaching in the Riverland of South Australia present an analytical description of the educational dynamics of this system. From this analysis, five elements are identified which underpin the process of successful vertical integration: (1) raised educational stakes; (2) local ownership; (3) broad university role; (4) longer attachments; and (5) shared workforce vision. Given the benefits to the Riverland medical education programs described in this paper, it is not surprising that vertical integration of medical education is a popular goal in many rural regions throughout the world. Although different contexts will result in different functional arrangements, it could be argued that the five principles outlined in this article can be applied in any region.

UAS Well Clear Recovery Against Non-Cooperative Intruders Using Vertical Maneuvers

NASA Technical Reports Server (NTRS)

Cone, Andrew; Thipphavong, David; Lee, Seung Man; Santiago, Confesor

2017-01-01

This paper documents a study that drove the development of a mathematical expression in the minimum operational performance standards (MOPS) of detect-and-avoid (DAA) systems for unmanned aircraft systems (UAS). This equation describes the conditions under which vertical maneuver guidance could be provided during recovery of well clear separation with a non-cooperative VFR aircraft in addition to horizontal maneuver guidance. Although suppressing vertical maneuver guidance in these situations increased the minimum horizontal separation from 500 to 800 feet, the maximum severity of loss of well clear increased in about 35 of the encounters compared to when a vertical maneuver was preferred and allowed. Additionally, analysis of individual cases led to the identification of a class of encounter where vertical rate error had a large effect on horizontal maneuvers due to the difficulty of making the correct left-right turn decision: crossing conflict with intruder changing altitude. These results supported allowing vertical maneuvers when UAS vertical performance exceeds the relative vertical position and velocity accuracy of the DAA tracker given the current velocity of the UAS and the relative vertical position and velocity estimated by the DAA tracker. Looking ahead, these results indicate a need to improve guidance algorithms by utilizing maneuver stability and near mid-air collision risk when determining maneuver guidance to regain well clear separation.

Highly ordered vertical structure of Synechococcus populations within the one-millimeter-thick photic zone of a hot spring cyanobacterial mat

NASA Technical Reports Server (NTRS)

Ramsing, N. B.; Ferris, M. J.; Ward, D. M.

2000-01-01

A variety of contemporary techniques were used to investigate the vertical distribution of thermophilic unicellular cyanobacteria, Synechococcus spp., and their activity within the upper 1-mm-thick photic zone of the mat community found in an alkaline siliceous hot spring in Yellowstone National Park in Wyoming. Detailed measurements were made over a diel cycle at a 61 degrees C site. Net oxygenic photosynthesis measured with oxygen microelectrodes was highest within the uppermost 100- to 200-microm-thick layer until midmorning, but as the day progressed, the peak of net activity shifted to deeper layers, stabilizing at a depth of 300 microm from midday throughout the afternoon. Examination of vertical thin sections by bright-field and autofluorescence microscopy revealed the existence of different populations of Synechococcus which form discrete bands at different vertical positions. Denaturing gradient gel electrophoresis analysis of PCR-amplified 16S rRNA gene segments from horizontal cryosections obtained at 100-microm-thick vertical intervals also suggested vertical stratification of cyanobacterial, green sulfur bacterium-like, and green nonsulfur bacterium-like populations. There was no evidence of diel migration. However, image analysis of vertical thin sections revealed the presence of a narrow band of rod-shaped Synechococcus cells in which the cells assumed an upright position. These upright cells, located 400 to 800 microm below the surface, were observed only in mat samples obtained around noon. In mat samples obtained at other time points, the cells were randomly oriented throughout the mat. These combined observations reveal the existence of a highly ordered structure within the very thin photic zone of this hot spring microbial mat, consisting of morphologically similar Synechococcus populations that are likely to be differentially adapted, some co-occurring with green sulfur bacterium-like populations, and all overlying green nonsulfur bacterium

Topogrid Derived 10 Meter Resolution Digital Elevation Model of the Shenandoah National Park and Surrounding Region, Virginia

USGS Publications Warehouse

Chirico, Peter G.; Tanner, Seth D.

2004-01-01

Explanation The purpose of developing a new 10m resolution DEM of the Shenandoah National Park Region was to more accurately depict geologic structure, surfical geology, and landforms of the Shenandoah National Park Region in preparation for automated landform classification. Previously, only a 30m resolution DEM was available through the National Elevation Dataset (NED). During production of the Shenandoah10m DEM of the Park the Geography Discipline of the USGS completed a revised 10m DEM to be included into the NED. However, different methodologies were used to produce the two similar DEMs. The ANUDEM algorithm was used to develop the Shenadoah DEM data. This algorithm allows for the inclusion of contours, streams, rivers, lake and water body polygons as well as spot height data to control the elevation model. A statistical analysis using over 800 National Geodetic Survey (NGS) first and second order vertical control points reveals that the Shenandoah10m DEM, produced as a part of the Appalachian Blue Ridge Landscape project, has a vertical accuracy of ?4.87 meters. The metadata for the 10m NED data reports a vertical accuracy of ?7m. A table listing the NGS control points, the elevation comparison, and the RMSE for the Shenandoah10m DEM is provided. The process of automated terrain classification involves developing statistical signatures from the DEM for each type of surficial deposit and landform type. The signature will be a measure of several characteristics derived from the elevation data including slope, aspect, planform curvature, and profile curvature. The quality of the DEM is of critical importance when extracting terrain signatures. The highest possible horizontal and vertical accuracy is required. The more accurate Shenandoah 10m DEM can now be analyzed and integrated with the geologic observations to yield statistical correlations between the two in the development of landform and surface geology mapping projects.

Hydraulic induced instability on a vertical service

NASA Technical Reports Server (NTRS)

Bosmans, R. F.

1985-01-01

The case history contained provides insight toward the mechanical and hydraulic behavior of a vertical pump. It clearly demonstrates the need for measurements on the rotor at or near the impeller area. The results are reported of an analysis on a service water pump. This pump is typical of the water pumps used throughout the power generation industry. Although little is known of the mechanical behavior of vertical pumps because of difficulty in modeling the rotor system, recent developments in the application of submersible proximity transducers have made possible the measurement of pump dynamics under operating conditions. The purpose of this study was to determine the proper selection and installation of vibration-monitoring transducers as well as to measure the effects of imbalance, misalignment, and hydraulics on the performance and reliability of vertical pumps. In addition, the cause of shaft failures on this pump was to be determined.

Vertical and lateral heterogeneous integration

NASA Astrophysics Data System (ADS)

Geske, Jon; Okuno, Yae L.; Bowers, John E.; Jayaraman, Vijay

2001-09-01

A technique for achieving large-scale monolithic integration of lattice-mismatched materials in the vertical direction and the lateral integration of dissimilar lattice-matched structures has been developed. The technique uses a single nonplanar direct-wafer-bond step to transform vertically integrated epitaxial structures into lateral epitaxial variation across the surface of a wafer. Nonplanar wafer bonding is demonstrated by integrating four different unstrained multi-quantum-well active regions lattice matched to InP on a GaAs wafer surface. Microscopy is used to verify the quality of the bonded interface, and photoluminescence is used to verify that the bonding process does not degrade the optical quality of the laterally integrated wells. The authors propose this technique as a means to achieve greater levels of wafer-scale integration in optical, electrical, and micromechanical devices.

Hydrologic Connectivity Estimated throughout the Nation's River Corridors

NASA Astrophysics Data System (ADS)

Hunt, R.; Borchardt, M. A.; Bradbury, K. R.

2014-12-01

Hydrologic connectivity is a key concept that integrates longitudinal transport in rivers with vertical and lateral exchanges between rivers and hyporheic zones, riparian wetlands, floodplains, and ponded aquatic ecosystems. Desirable levels of connectivity are thought to be associated with rivers that are well-connected longitudinally while also being well connected vertically and laterally with marginal waters where carbon and nutrients are efficiently transformed, and where aquatic organisms feed, or are reared, or take refuge during floods. But what is the proper balance between longitudinal and vertical and lateral connectivity? We took a step towards quantifying hydrologic connectivity using the model NEXSS (Gomez-Velez and Harvey, 2014, GRL) applied throughout the nation's rivers. NEXSS simulates vertical and lateral connectivity and compares it with longitudinal transport along the river's main axis. It uses as inputs measured network topology for first to eighth order channels, river hydraulic geometry, sediment grain size, bedform types and sizes, estimated hydraulic conductivity of sediments, and estimates of reaction rates such as denitrification. Results indicate that hyporheic flow is large enough to exchange a river's entire volume many times within a river network, which increases biogeochemical opportunities for nutrient processing and attenuation of contaminants. Also, the analysis demonstrated why and where (i.e., in which physiographic regions of the nation) are hyporheic flow and solute reactions the greatest. The cumulative influence of hydrologic connectivity on water quality is expressed by a dimensionless index of reaction significance. Our quantification of hydrologic connectivity adds a physical basis that supports water quality modeling, and also supports scientifically based prioritization of management actions (e.g. stream restoration) and may support other types of actions (e.g. legislative actions) to help conserve healthy functional

Hydrologic Connectivity Estimated throughout the Nation's River Corridors

NASA Astrophysics Data System (ADS)

Harvey, J. W.; Gomez-Velez, J. D.

2015-12-01

Hydrologic connectivity is a key concept that integrates longitudinal transport in rivers with vertical and lateral exchanges between rivers and hyporheic zones, riparian wetlands, floodplains, and ponded aquatic ecosystems. Desirable levels of connectivity are thought to be associated with rivers that are well-connected longitudinally while also being well connected vertically and laterally with marginal waters where carbon and nutrients are efficiently transformed, and where aquatic organisms feed, or are reared, or take refuge during floods. But what is the proper balance between longitudinal and vertical and lateral connectivity? We took a step towards quantifying hydrologic connectivity using the model NEXSS (Gomez-Velez and Harvey, 2014, GRL) applied throughout the nation's rivers. NEXSS simulates vertical and lateral connectivity and compares it with longitudinal transport along the river's main axis. It uses as inputs measured network topology for first to eighth order channels, river hydraulic geometry, sediment grain size, bedform types and sizes, estimated hydraulic conductivity of sediments, and estimates of reaction rates such as denitrification. Results indicate that hyporheic flow is large enough to exchange a river's entire volume many times within a river network, which increases biogeochemical opportunities for nutrient processing and attenuation of contaminants. Also, the analysis demonstrated why and where (i.e., in which physiographic regions of the nation) are hyporheic flow and solute reactions the greatest. The cumulative influence of hydrologic connectivity on water quality is expressed by a dimensionless index of reaction significance. Our quantification of hydrologic connectivity adds a physical basis that supports water quality modeling, and also supports scientifically based prioritization of management actions (e.g. stream restoration) and may support other types of actions (e.g. legislative actions) to help conserve healthy functional

Spatial Vertical Directionality and Correlation of Low-Frequency Ambient Noise in Deep Ocean Direct-Arrival Zones.

PubMed

Yang, Qiulong; Yang, Kunde; Cao, Ran; Duan, Shunli

2018-01-23

Wind-driven and distant shipping noise sources contribute to the total noise field in the deep ocean direct-arrival zones. Wind-driven and distant shipping noise sources may significantly and simultaneously affect the spatial characteristics of the total noise field to some extent. In this work, a ray approach and parabolic equation solution method were jointly utilized to model the low-frequency ambient noise field in a range-dependent deep ocean environment by considering their calculation accuracy and efficiency in near-field wind-driven and far-field distant shipping noise fields. The reanalysis databases of National Center of Environment Prediction (NCEP) and Volunteer Observation System (VOS) were used to model the ambient noise source intensity and distribution. Spatial vertical directionality and correlation were analyzed in three scenarios that correspond to three wind speed conditions. The noise field was dominated by distant shipping noise sources when the wind speed was less than 3 m/s, and then the spatial vertical directionality and vertical correlation of the total noise field were nearly consistent with those of distant shipping noise field. The total noise field was completely dominated by near field wind generated noise sources when the wind speed was greater than 12 m/s at 150 Hz, and then the spatial vertical correlation coefficient and directionality pattern of the total noise field was approximately consistent with that of the wind-driven noise field. The spatial characteristics of the total noise field for wind speeds between 3 m/s and 12 m/s were the weighted results of wind-driven and distant shipping noise fields. Furthermore, the spatial characteristics of low-frequency ambient noise field were compared with the classical Cron/Sherman deep water noise field coherence function. Simulation results with the described modeling method showed good agreement with the experimental measurement results based on the vertical line array deployed near

Spatial Vertical Directionality and Correlation of Low-Frequency Ambient Noise in Deep Ocean Direct-Arrival Zones

PubMed Central

Yang, Qiulong; Yang, Kunde; Cao, Ran; Duan, Shunli

2018-01-01

Wind-driven and distant shipping noise sources contribute to the total noise field in the deep ocean direct-arrival zones. Wind-driven and distant shipping noise sources may significantly and simultaneously affect the spatial characteristics of the total noise field to some extent. In this work, a ray approach and parabolic equation solution method were jointly utilized to model the low-frequency ambient noise field in a range-dependent deep ocean environment by considering their calculation accuracy and efficiency in near-field wind-driven and far-field distant shipping noise fields. The reanalysis databases of National Center of Environment Prediction (NCEP) and Volunteer Observation System (VOS) were used to model the ambient noise source intensity and distribution. Spatial vertical directionality and correlation were analyzed in three scenarios that correspond to three wind speed conditions. The noise field was dominated by distant shipping noise sources when the wind speed was less than 3 m/s, and then the spatial vertical directionality and vertical correlation of the total noise field were nearly consistent with those of distant shipping noise field. The total noise field was completely dominated by near field wind generated noise sources when the wind speed was greater than 12 m/s at 150 Hz, and then the spatial vertical correlation coefficient and directionality pattern of the total noise field was approximately consistent with that of the wind-driven noise field. The spatial characteristics of the total noise field for wind speeds between 3 m/s and 12 m/s were the weighted results of wind-driven and distant shipping noise fields. Furthermore, the spatial characteristics of low-frequency ambient noise field were compared with the classical Cron/Sherman deep water noise field coherence function. Simulation results with the described modeling method showed good agreement with the experimental measurement results based on the vertical line array deployed near

Vertical control in the Class III compensatory treatment.

PubMed

Sobral, Márcio Costa; Habib, Fernando A L; Nascimento, Ana Carla de Souza

2013-01-01

Compensatory orthodontic treatment, or simply orthodontic camouflage, consists in an important alternative to orthognathic surgery in the resolution of skeletal discrepancies in adult patients. It is important to point that, to be successfully performed, diagnosis must be detailed, to evaluate, specifically, dental and facial features, as well as the limitations imposed by the magnitude of the discrepancy. The main complaint, patient's treatment expectation, periodontal limits, facial pattern and vertical control are some of the items to be explored in the determination of the viability of a compensatory treatment. Hyperdivergent patients who present with a Class III skeletal discrepancy, associated with a vertical facial pattern, with the presence or tendency to anterior open bite, deserve special attention. In these cases, an efficient strategy of vertical control must be planned and executed. The present article aims at illustrating the evolution of efficient alternatives of vertical control in hiperdivergent patients, from the use, in the recent past, of extraoral appliances on the lower dental arch (J-hook), until nowadays, with the advent of skeletal anchorage. But for patients with a more balanced facial pattern, the conventional mechanics with Class III intermaxillary elastics, associated to an accentuated curve of Spee in the upper arch and a reverse curve of Spee in the lower arch, and vertical elastics in the anterior region, continues to be an excellent alternative, if there is extreme collaboration in using the elastics.

Links - Helpful Tools | Alaska Division of Geological & Geophysical Surveys

Science.gov Websites

Tidal Datum Portal Climate and Cryosphere Hazards Coastal Hazards Program Guide to Geologic Hazards in Systems Alaska Tidal Datum Portal For Alaska's coastal communities, an understanding and awareness of local tidal datums is critical to assessing vulnerability and planning responses to coastal geohazards

A vertical handoff decision algorithm based on ARMA prediction model

NASA Astrophysics Data System (ADS)

Li, Ru; Shen, Jiao; Chen, Jun; Liu, Qiuhuan

2012-01-01

With the development of computer technology and the increasing demand for mobile communications, the next generation wireless networks will be composed of various wireless networks (e.g., WiMAX and WiFi). Vertical handoff is a key technology of next generation wireless networks. During the vertical handoff procedure, handoff decision is a crucial issue for an efficient mobility. Based on auto regression moving average (ARMA) prediction model, we propose a vertical handoff decision algorithm, which aims to improve the performance of vertical handoff and avoid unnecessary handoff. Based on the current received signal strength (RSS) and the previous RSS, the proposed approach adopt ARMA model to predict the next RSS. And then according to the predicted RSS to determine whether trigger the link layer triggering event and complete vertical handoff. The simulation results indicate that the proposed algorithm outperforms the RSS-based scheme with a threshold in the performance of handoff and the number of handoff.

RADIALLY MAGNETIZED PROTOPLANETARY DISK: VERTICAL PROFILE

DOE Office of Scientific and Technical Information (OSTI.GOV)

Russo, Matthew; Thompson, Christopher

2015-11-10

This paper studies the response of a thin accretion disk to an external radial magnetic field. Our focus is on protoplanetary disks (PPDs), which are exposed during their later evolution to an intense, magnetized wind from the central star. A radial magnetic field is mixed into a thin surface layer, wound up by the disk shear, and pushed downward by a combination of turbulent mixing and ambipolar and ohmic drift. The toroidal field reaches much greater strengths than the seed vertical field that is usually invoked in PPD models, even becoming superthermal. Linear stability analysis indicates that the disk experiencesmore » the magnetorotational instability (MRI) at a higher magnetization than a vertically magnetized disk when both the effects of ambipolar and Hall drift are taken into account. Steady vertical profiles of density and magnetic field are obtained at several radii between 0.06 and 1 AU in response to a wind magnetic field B{sub r} ∼ (10{sup −4}–10{sup −2})(r/ AU){sup −2} G. Careful attention is given to the radial and vertical ionization structure resulting from irradiation by stellar X-rays. The disk is more strongly magnetized closer to the star, where it can support a higher rate of mass transfer. As a result, the inner ∼1 AU of a PPD is found to evolve toward lower surface density. Mass transfer rates around 10{sup −8} M{sub ⊙} yr{sup −1} are obtained under conservative assumptions about the MRI-generated stress. The evolution of the disk and the implications for planet migration are investigated in the accompanying paper.« less

The vertical distribution of tropospheric ammonia

NASA Technical Reports Server (NTRS)

Levine, J. S.; Hoell, J. M.; Augustsson, T. R.

1980-01-01

A one-dimensional tropospheric photochemical model is used to simulate measured profiles of NH3 obtained with the Infrared Heterodyne Radiometer. The relative roles of homogeneous loss, heterogeneous loss, and vertical eddy transport are discussed in terms of selecting parameters which best fit the measurements. The best fit was obtained for a vertical eddy diffusion coefficient of 200,000/sq cm per sec or greater (corresponding to a characteristic vertical transport time in excess of about 35 days), and a characteristic heterogeneous loss time in excess of 10 days. The characteristic homogeneous chemical loss time was found to be about 40 days at the surface and decreased to about 180 days at 10 km, and not very sensitive to model chemical perturbations. Increased ground-level concentrations of NH3 to about 10 ppb, compared to background surface concentrations of about 1 ppb, were measured several weeks after application of ammonium nitrate fertilizer. This suggests that the volatilization of ammonium nitrate fertilizer is rapid, and an important source of NH3. Because of the characteristic times for the loss mechanisms, synoptic time-scale phenomena may play an important role in determining the tropospheric distribution of NH3 concentrations.

Human sensitivity to vertical self-motion.

PubMed

Nesti, Alessandro; Barnett-Cowan, Michael; Macneilage, Paul R; Bülthoff, Heinrich H

2014-01-01

Perceiving vertical self-motion is crucial for maintaining balance as well as for controlling an aircraft. Whereas heave absolute thresholds have been exhaustively studied, little work has been done in investigating how vertical sensitivity depends on motion intensity (i.e., differential thresholds). Here we measure human sensitivity for 1-Hz sinusoidal accelerations for 10 participants in darkness. Absolute and differential thresholds are measured for upward and downward translations independently at 5 different peak amplitudes ranging from 0 to 2 m/s(2). Overall vertical differential thresholds are higher than horizontal differential thresholds found in the literature. Psychometric functions are fit in linear and logarithmic space, with goodness of fit being similar in both cases. Differential thresholds are higher for upward as compared to downward motion and increase with stimulus intensity following a trend best described by two power laws. The power laws' exponents of 0.60 and 0.42 for upward and downward motion, respectively, deviate from Weber's Law in that thresholds increase less than expected at high stimulus intensity. We speculate that increased sensitivity at high accelerations and greater sensitivity to downward than upward self-motion may reflect adaptations to avoid falling.

Nonverbal behavior and the vertical dimension of social relations: a meta-analysis.

PubMed

Hall, Judith A; Coats, Erik J; LeBeau, Lavonia Smith

2005-11-01

The vertical dimension of interpersonal relations (relating to dominance, power, and status) was examined in association with nonverbal behaviors that included facial behavior, gaze, interpersonal distance, body movement, touch, vocal behaviors, posed encoding skill, and others. Results were separately summarized for people's beliefs (perceptions) about the relation of verticality to nonverbal behavior and for actual relations between verticality and nonverbal behavior. Beliefs/perceptions were stronger and much more prevalent than were actual verticality effects. Perceived and actual relations were positively correlated across behaviors. Heterogeneity was great, suggesting that verticality is not a psychologically uniform construct in regard to nonverbal behavior. Finally, comparison of the verticality effects to those that have been documented for gender in relation to nonverbal behavior revealed only a limited degree of parallelism.

[Incidence of congenital syphilis and factors associated with vertical transmission: data from the Birth in Brazil study].

PubMed

Domingues, Rosa Maria Soares Madeira; Leal, Maria do Carmo

2016-06-20

The objectives were to estimate incidence of congenital syphilis and verify factors associated with vertical transmission. A national hospital-based study was performed in 2011-2012 with 23,894 postpartum women using an in-hospital interview and data from patient charts and prenatal cards. Univariate logistic regression was performed to verify factors associated with congenital syphilis. Estimated incidence of congenital syphilis was 3.51 per 1,000 live births (95%CI: 2.29-5.37) and vertical transmission rate was 34.3% (95%CI: 24.7-45.4). Congenital syphilis was associated with lower maternal schooling, black skin color, higher rate of risk factors for prematurity, late initiation of prenatal care, fewer prenatal visits, and lower rate of prenatal serological testing. Fetal mortality was six times higher in congenital syphilis, and newborns with congenital syphilis showed higher hospital admission rates. Congenital syphilis is a persistent public health problem in Brazil and is associated with greater social vulnerability and gaps in prenatal care.

Horizontal Cross Bracing Detail, Vertical Cross Bracing Detail, Horizontal Cross ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Horizontal Cross Bracing Detail, Vertical Cross Bracing Detail, Horizontal Cross Bracing Detail, Vertical Cross Bracing-End Detail - Cumberland Covered Bridge, Spanning Mississinewa River, Matthews, Grant County, IN

GPS vertical axis performance enhancement for helicopter precision landing approach

NASA Technical Reports Server (NTRS)

Denaro, Robert P.; Beser, Jacques

1986-01-01

Several areas were investigated for improving vertical accuracy for a rotorcraft using the differential Global Positioning System (GPS) during a landing approach. Continuous deltaranging was studied and the potential improvement achieved by estimating acceleration was studied by comparing the performance on a constant acceleration turn and a rough landing profile of several filters: a position-velocity (PV) filter, a position-velocity-constant acceleration (PVAC) filter, and a position-velocity-turning acceleration (PVAT) filter. In overall statistics, the PVAC filter was found to be most efficient with the more complex PVAT performing equally well. Vertical performance was not significantly different among the filters. Satellite selection algorithms based on vertical errors only (vertical dilution of precision or VDOP) and even-weighted cross-track and vertical errors (XVDOP) were tested. The inclusion of an altimeter was studied by modifying the PVAC filter to include a baro bias estimate. Improved vertical accuracy during degraded DOP conditions resulted. Flight test results for raw differential results excluding filter effects indicated that the differential performance significantly improved overall navigation accuracy. A landing glidepath steering algorithm was devised which exploits the flexibility of GPS in determining precise relative position. A method for propagating the steering command over the GPS update interval was implemented.

A Pseudo-Vertical Equilibrium Model for Slow Gravity Drainage Dynamics

NASA Astrophysics Data System (ADS)

Becker, Beatrix; Guo, Bo; Bandilla, Karl; Celia, Michael A.; Flemisch, Bernd; Helmig, Rainer

2017-12-01

Vertical equilibrium (VE) models are computationally efficient and have been widely used for modeling fluid migration in the subsurface. However, they rely on the assumption of instant gravity segregation of the two fluid phases which may not be valid especially for systems that have very slow drainage at low wetting phase saturations. In these cases, the time scale for the wetting phase to reach vertical equilibrium can be several orders of magnitude larger than the time scale of interest, rendering conventional VE models unsuitable. Here we present a pseudo-VE model that relaxes the assumption of instant segregation of the two fluid phases by applying a pseudo-residual saturation inside the plume of the injected fluid that declines over time due to slow vertical drainage. This pseudo-VE model is cast in a multiscale framework for vertically integrated models with the vertical drainage solved as a fine-scale problem. Two types of fine-scale models are developed for the vertical drainage, which lead to two pseudo-VE models. Comparisons with a conventional VE model and a full multidimensional model show that the pseudo-VE models have much wider applicability than the conventional VE model while maintaining the computational benefit of the conventional VE model.

A new approach to the treatment of congenital vertical talus

PubMed Central

Alaee, Farhang; Boehm, Stephanie

2007-01-01

Congenital vertical talus is an uncommon foot deformity that is present at birth and results in a rigid flatfoot deformity. Left untreated the deformity can result in pain and disability. Though the exact etiology of vertical talus is unknown, an increasing number of cases have been shown to have a genetic cause. Approximately 50% of all cases of vertical talus are associated with other neuromuscular abnormalities or known genetic syndromes. The remaining 50% of cases were once thought to be idiopathic in nature. However, there is increasing evidence that many of these cases are related to single gene defects. Most patients with vertical talus have been treated with major reconstructive surgeries that are fraught with complications such as wound necrosis, talar necrosis, undercorrection of the deformity, stiffness of the ankle and subtalar joint, and the eventual need for multiple operative procedures. Recently, a new approach to vertical talus that consists of serial casting and minimal surgery has resulted in excellent correction in the short-term. Longer follow-up will be necessary to ensure maintenance of correction with this new technique. A less invasive approach to the correction of vertical talus may provide more favorable long-term outcomes than more extensive surgery as has been shown to be true for clubfoot outcomes. PMID:19308490

Understanding Coastal Wetland Vulnerability to Sea-Level Rise Enhanced Inundation Using Real-Time Stage Monitoring, LiDAR, and Monte Carlo Simulation in Everglades National Park

NASA Astrophysics Data System (ADS)

Cooper, H.; Zhang, C.

2017-12-01

Coastal wetlands are one of the most productive ecological systems in the world, providing critical habitat area and valuable ecosystem services such as carbon sequestration. However, due to their location in low lying areas, coastal wetlands are particularly vulnerable to sea-level rise (SLR). Everglades National Park (ENP) encompasses the southern-most portion of the Greater Everglades Ecosystem, and is the largest subtropical wetland in the USA. Water depths have shown to have a significant relationship to vegetation community composition and organization while also playing a crucial role in vegetation health throughout the Everglades. Live plants play a vital role in maintaining soil structure (i.e. elevation), and decreases in vegetation health can cause peat collapse or wetland loss resulting in dramatic habitat, organic soil, and elevation loss posing concerns for Everglades management and restoration. One suspected mechanism for peat collapse is enhanced inundation due to SLR, thus mapping and modeling water depths is a critical component to understanding the potential impacts of future SLR. Previous research in the Everglades focused on a conventional Water Depth Model (WDM) approach where a Digital Elevation Model (DEM) is subtracted from a Water Table Elevation Model (WTEM). In this study, the conventional WDM approach is extended to a more rigorous WDM technique so that the accuracy and precision of the underlying data may be considered. Monte Carlo simulation is used to propagate probability distributions through our SLR depth model using our Random Forest-based LiDAR DEM, Empirical Bayesian Kriging-based WTEMs, uncertainties in vertical datums, soil accretion projections, and regional sea-level rise projections. Water depth maps were produced for the wet and dry seasons in April and October, which successfully revealed the potential spatial and temporal water depth variations due to future SLR. It is concluded that a more rigorous WDM technique helps

Vertical cross-spectral phases in atmospheric flow

NASA Astrophysics Data System (ADS)

Chougule, A.; Mann, J.; Kelly, M.

2014-11-01

The cross-spectral phases between velocity components at two heights are analyzed from observations at the Høvsøre test site under diabatic conditions. These phases represent the degree to which turbulence sensed at one height leads (or lags) in time the turbulence sensed at the other height. The phase angle of the cross-wind component is observed to be significantly greater than the phase for the along-wind component, which in turn is greater than the phase for the vertical component. The cross-wind and along-wind phases increase with stream-wise wavenumber and vertical separation distance, but there is no significant change in the phase angle of vertical velocity. The phase angles for all atmospheric stabilities show similar order in phasing. The phase angles from the Høvsøre observations under neutral condition are compared with a rapid distortion theory model which show similar order in phase shift.

Purification process for vertically aligned carbon nanofibers

NASA Technical Reports Server (NTRS)

Nguyen, Cattien V.; Delziet, Lance; Matthews, Kristopher; Chen, Bin; Meyyappan, M.

2003-01-01

Individual, free-standing, vertically aligned multiwall carbon nanotubes or nanofibers are ideal for sensor and electrode applications. Our plasma-enhanced chemical vapor deposition techniques for producing free-standing and vertically aligned carbon nanofibers use catalyst particles at the tip of the fiber. Here we present a simple purification process for the removal of iron catalyst particles at the tip of vertically aligned carbon nanofibers derived by plasma-enhanced chemical vapor deposition. The first step involves thermal oxidation in air, at temperatures of 200-400 degrees C, resulting in the physical swelling of the iron particles from the formation of iron oxide. Subsequently, the complete removal of the iron oxide particles is achieved with diluted acid (12% HCl). The purification process appears to be very efficient at removing all of the iron catalyst particles. Electron microscopy images and Raman spectroscopy data indicate that the purification process does not damage the graphitic structure of the nanotubes.

Measurement of vertical stability metrics in KSTAR

NASA Astrophysics Data System (ADS)

Hahn, Sang-Hee; Humphreys, D. A.; Mueller, D.; Bak, J. G.; Eidietis, N. W.; Kim, H.-S.; Ko, J. S.; Walker, M. L.; Kstar Team

2017-10-01

The paper summarizes results of multi-year ITPA experiments regarding measurement of the vertical stabilization capability of KSTAR discharges, including most recent measurements at the highest achievable elongation (κ 2.0 - 2.1). The measurements of the open-loop growth rate of VDE (γz) and the maximum controllable vertical displacement (ΔZmax) are done by the release-and-catch method. The dynamics of the vertical movement of the plasma is verified by both relevant magnetic reconstructions and non-magnetic diagnostics. The measurements of γz and ΔZmax were done for different plasma currents, βp, internal inductances, elongations and different configurations of the vessel conductors that surround the plasma as the first wall. Effects of control design choice and diagnostics noise are discussed, and comparison with the axisymmetric plasma response model is given for partial accounting for the measured control capability. This work supported by Ministry of Science, ICT, and Future Planning under KSTAR project.

A search for thermospheric composition perturbations due to vertical winds

NASA Astrophysics Data System (ADS)

Krynicki, Matthew P.

The thermosphere is generally in hydrostatic equilibrium, with winds blowing horizontally along stratified constant-pressure surfaces, driven by the dayside-to-nightside pressure gradient. A marked change in this paradigm resulted after Spencer et al. [1976] reported vertical wind measurements of 80 m·s-1 from analyses of AE-C satellite data. It is now established that the thermosphere routinely supports large-magnitude (˜30-150 m·s-1) vertical winds at auroral latitudes. These vertical winds represent significant departure from hydrostatic and diffusive equilibrium, altering locally---and potentially globally---the thermosphere's and ionosphere's composition, chemistry, thermodynamics and energy budget. Because of their localized nature, large-magnitude vertical wind effects are not entirely known. This thesis presents ground-based Fabry-Perot Spectrometer OI(630.0)-nm observations of upper-thermospheric vertical winds obtained at Inuvik, NT, Canada and Poker Flat, AK. The wind measurements are compared with vertical displacement estimates at ˜104 km2 horizontal spatial scales determined from a new modification to the electron transport code of Lummerzheim and Lilensten [1994] as applied to FUV-wavelength observations by POLAR spacecraft's Ultraviolet Imager [Torr et al. , 1995]. The modification, referred to as the column shift, simulates vertical wind effects such as neutral transport and disruption of diffusive equilibrium by vertically displacing the Hedin [1991] MSIS-90 [O2]/[N2] and [O]/([N2]+[O2]) mixing ratios and subsequently redistributing the O, O2, and N 2 densities used in the transport code. Column shift estimates are inferred from comparisons of UVI OI(135.6)-nm auroral observations to their corresponding modeled emission. The modeled OI(135.6)-nm brightness is determined from the modeled thermospheric response to electron precipitation and estimations of the energy flux and characteristic energy of the precipitation, which are inferred from UVI

Structural design of the Sandia 34-M Vertical Axis Wind Turbine

NASA Astrophysics Data System (ADS)

Berg, D. E.

Sandia National Laboratories, as the lead DOE laboratory for Vertical Axis Wind Turbine (VAWT) development, is currently designing a 34-meter diameter Darrieus-type VAWT. This turbine will be a research test bed which provides a focus for advancing technology and validating design and fabrication techniques in a size range suitable for utility use. Structural data from this machine will allow structural modeling to be refined and verified for a turbine on which the gravity effects and stochastic wind loading are significant. Performance data from it will allow aerodynamic modeling to be refined and verified. The design effort incorporates Sandia's state-of-the-art analysis tools in the design of a complete machine. The analytic tools used in this design are discussed and the conceptual design procedure is described.

Vertical axis wind turbine power regulation through centrifugally pumped lift spoiling

NASA Astrophysics Data System (ADS)

Klimas, P. C.; Sladky, J. F., Jr.

This paper describes an approach for lowering the rated windspeeds of Darrieus-type vertical axis wind turbines (VAWTs) whose blades are hollow aluminum extrusions. The blades, which when rotating act as centrifugal pumps, are fitted with a series of small perforations distributed along a portion of the blades' span. By valving the ends of the hollow blades, flow into the blade ends and out of the perforations may be controlled. This flow can induce premature aerodynamic stall on the blade elements, thereby reducing both the rated power of the turbine and its cost-of-energy. The concept has been proven on the Sandia National Laboratories 5-m diameter research VAWT and force balance and flow visualization wind tunnel tests have been conducted using a blade section designed for the VAWT application.

Nuclear microprobe investigation of the effects of ionization and displacement damage in vertical, high voltage GaN diodes

DOE PAGES

Vizkelethy, G.; King, M. P.; Aktas, O.; ...

2016-12-02

Radiation responses of high-voltage, vertical gallium-nitride (GaN) diodes were investigated using Sandia National Laboratories’ nuclear microprobe. Effects of the ionization and the displacement damage were studied using various ion beams. We found that the devices show avalanche effect for heavy ions operated under bias well below the breakdown voltage. Here, the displacement damage experiments showed a surprising effect for moderate damage: the charge collection efficiency demonstrated an increase instead of a decrease for higher bias voltages.

Nuclear microprobe investigation of the effects of ionization and displacement damage in vertical, high voltage GaN diodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vizkelethy, G.; King, M. P.; Aktas, O.

Radiation responses of high-voltage, vertical gallium-nitride (GaN) diodes were investigated using Sandia National Laboratories’ nuclear microprobe. Effects of the ionization and the displacement damage were studied using various ion beams. We found that the devices show avalanche effect for heavy ions operated under bias well below the breakdown voltage. Here, the displacement damage experiments showed a surprising effect for moderate damage: the charge collection efficiency demonstrated an increase instead of a decrease for higher bias voltages.

Evaluation of Aesthetic Function and Thermal Modification of Vertical Greenery at Bogor City, Indonesia

NASA Astrophysics Data System (ADS)

Sulistyantara, B.; Sesara, R.

2017-10-01

Bogor city currently develops vertical greenery due to counter the decreasing of green space quantity. Vertical greenery is a planting method using vertical structure similar to retaining walls. There are some benefits of vertical greenery, such as providing aesthetics value of the landscape, to protect from the heat, to reduce noise, and to reduce pollution. The purpose of this study were to identify thermal modification by vertical greenery in Bogor city, to assess the aesthetics value from vertical greenery, and to provide a recommendation in attempt to manage and improve the quality of vertical greenery in Bogor city. The study was conducted using Scenic Beauty Estimation method, and was done by providing questionnaires to the respondents in order to assess the aesthetics value of vertical greenery. Infrared thermometer was also used to measure the surface’s temperature to evaluate thermal modification function of the vertical greenery. The result of study proved that vertical greenery in the Bogor city has considerably good aesthetic. It also showed that there is a decreasing in surface temperature of the vertical greenery structure.

Investigation of shortcomings in simulated aerosol vertical profiles

NASA Astrophysics Data System (ADS)

Park, S.; Allen, R.

2017-12-01

The vertical distribution of aerosols is one important factor for aerosol radiative forcing. Previous studies show that climate models poorly reproduce the aerosol vertical profile, with too much aerosol aloft in the upper troposphere. This bias may be related to several factors, including excessive convective mass flux and wet removal. In this study, we evaluate the aerosol vertical profile from several Coupled Model Intercomparison Project 5 (CMIP5) models, as well as the Community Atmosphere Model 5 (CAM5), relative to the Cloud-Aerosol Lidar Infrared Pathfinder Satellite Observation (CALIPSO). The results show that all models significantly underestimate extinction coefficient in the lower troposphere, while overestimating extinction coefficient in the upper troposphere. In addition, the majority of models indicate a land-ocean dependence in the relationship between aerosol extinction coefficient in the upper troposphere and convective mass flux. Over the continents, more convective mass flux is related to more aerosol aloft; over the ocean, more convective mass flux is associated with less aerosol in upper troposphere. Sensitivity experiments are conducted to investigate the role that convection and wet deposition have in contributing to the deficient simulation of the vertical aerosol profile, including the land-ocean dependence.

Aerothermoelastic Analysis of a NASP-Like Vertical Fin

NASA Technical Reports Server (NTRS)

Rodgers, John P.

1992-01-01

Several aeroelastic stability analyses for a vertical fin similar to that of the National Aero-Space Plane are described. The objectives of the study were to design and obtain an experimental data base for a supersonic wind-tunnel model of the fin in order to examine the effects of thermal loading on the flutter characteristics. This paper describes the preliminary efforts to design the wind-tunnel model, including several of the geometric parameter variations that were analyzed. The dominant flutter mechanism involved a flap vibration mode and a fin bending mode. Variation of the thicknesses of flap and root flexures, used to attach the flap to the fin, and the fin to a support, significantly affected the flutter boundary. Uniform thermal loads, affecting only material properties, had little effect, as did the application of different uniform temperatures to each side of the fin. In contrast, the application of significant chord-wise thermal gradients induced stresses which reduced the flutter dynamic pressure by as much as 37 percent. For less extreme distributed loading, the low-aspect ratio fin was relatively unaffected.

Comparing the role of absolute sea-level rise and vertical tectonic motions in coastal flooding, Torres Islands (Vanuatu)

PubMed Central

Ballu, Valérie; Bouin, Marie-Noëlle; Siméoni, Patricia; Crawford, Wayne C.; Calmant, Stephane; Boré, Jean-Michel; Kanas, Tony; Pelletier, Bernard

2011-01-01

Since the late 1990s, rising sea levels around the Torres Islands (north Vanuatu, southwest Pacific) have caused strong local and international concern. In 2002–2004, a village was displaced due to increasing sea incursions, and in 2005 a United Nations Environment Programme press release referred to the displaced village as perhaps the world’s first climate change “refugees.” We show here that vertical motions of the Torres Islands themselves dominate the apparent sea-level rise observed on the islands. From 1997 to 2009, the absolute sea level rose by 150 + /-20 mm. But GPS data reveal that the islands subsided by 117 + /-30 mm over the same time period, almost doubling the apparent gradual sea-level rise. Moreover, large earthquakes that occurred just before and after this period caused several hundreds of mm of sudden vertical motion, generating larger apparent sea-level changes than those observed during the entire intervening period. Our results show that vertical ground motions must be accounted for when evaluating sea-level change hazards in active tectonic regions. These data are needed to help communities and governments understand environmental changes and make the best decisions for their future. PMID:21795605

A hybrid downscaling procedure for estimating the vertical distribution of ambient temperature in local scale

NASA Astrophysics Data System (ADS)

Yiannikopoulou, I.; Philippopoulos, K.; Deligiorgi, D.

2012-04-01

The vertical thermal structure of the atmosphere is defined by a combination of dynamic and radiation transfer processes and plays an important role in describing the meteorological conditions at local scales. The scope of this work is to develop and quantify the predictive ability of a hybrid dynamic-statistical downscaling procedure to estimate the vertical profile of ambient temperature at finer spatial scales. The study focuses on the warm period of the year (June - August) and the method is applied to an urban coastal site (Hellinikon), located in eastern Mediterranean. The two-step methodology initially involves the dynamic downscaling of coarse resolution climate data via the RegCM4.0 regional climate model and subsequently the statistical downscaling of the modeled outputs by developing and training site-specific artificial neural networks (ANN). The 2.5ox2.5o gridded NCEP-DOE Reanalysis 2 dataset is used as initial and boundary conditions for the dynamic downscaling element of the methodology, which enhances the regional representivity of the dataset to 20km and provides modeled fields in 18 vertical levels. The regional climate modeling results are compared versus the upper-air Hellinikon radiosonde observations and the mean absolute error (MAE) is calculated between the four grid point values nearest to the station and the ambient temperature at the standard and significant pressure levels. The statistical downscaling element of the methodology consists of an ensemble of ANN models, one for each pressure level, which are trained separately and employ the regional scale RegCM4.0 output. The ANN models are theoretically capable of estimating any measurable input-output function to any desired degree of accuracy. In this study they are used as non-linear function approximators for identifying the relationship between a number of predictor variables and the ambient temperature at the various vertical levels. An insight of the statistically derived input

A new approach to biostratigraphy in the Karoo retroarc foreland system: Utilising restricted-range palynomorphs and their first appearance datums for correlation

NASA Astrophysics Data System (ADS)

Barbolini, Natasha; Rubidge, Bruce; Bamford, Marion K.

2018-04-01

The main Karoo Basin (MKB), internationally renowned for its wealth of fossil tetrapods, has been lithostratigraphically subdivided into three discrete regions: two (east and west) proximal facies adjacent to the Cape Fold Belt, and a distal facies, away from the Cape Fold Belt. Because of lithological differences between formations of the proximal and distal sectors of the MKB, it has been difficult to correlate time-equivalent lithostratigraphic units in the different sectors. Palynology provides a tool for refining stratigraphic correlations within the MKB, but only species with restricted ranges are biostratigraphically significant. Restricted-range palynomorph taxa from the Ecca and Beaufort groups indicate the following relationships: the lowermost Vryheid Formation palynoflora can be strongly correlated with that of the Prince Albert Formation, whereas the Whitehill-Collingham formations and No. 2 seam (Vryheid Formation), and the Ripon Formation and No. 4 seam (Vryheid Formation) can be tentatively linked using palynology. The lower-middle Normandien Formation in the north is chronologically equivalent to the Ripplemead member of the Balfour Formation in the south. Although the Ecca-Beaufort Group boundary is known to be diachronous, restricted-range palynomorphs cannot yet confirm that the uppermost Ecca Group in the northern part of the basin was deposited at the same time as the lower Beaufort Group in the south. This study demonstrates that despite diachronous ranges of some taxa, palynology is useful in correlating age-equivalent lithostratigraphic units in the proximal and distal sectors of the basin. A new First Appearance Datum (FAD) palynozonation for the Karoo is presented that is calibrated by the most recent radiometric dates for South Africa, Australia, and South America. The new zones are also correlated with Permian successions in Antarctica, Zambia, Botswana, and India. Future palynostratigraphic work in South Africa must take into account

Vertical Stratification Engineering for Organic Bulk-Heterojunction Devices.

PubMed

Huang, Liqiang; Wang, Gang; Zhou, Weihua; Fu, Boyi; Cheng, Xiaofang; Zhang, Lifu; Yuan, Zhibo; Xiong, Sixing; Zhang, Lin; Xie, Yuanpeng; Zhang, Andong; Zhang, Youdi; Ma, Wei; Li, Weiwei; Zhou, Yinhua; Reichmanis, Elsa; Chen, Yiwang

2018-05-22

High-efficiency organic solar cells (OSCs) can be produced through optimization of component molecular design, coupled with interfacial engineering and control of active layer morphology. However, vertical stratification of the bulk-heterojunction (BHJ), a spontaneous activity that occurs during the drying process, remains an intricate problem yet to be solved. Routes toward regulating the vertical separation profile and evaluating the effects on the final device should be explored to further enhance the performance of OSCs. Herein, we establish a connection between the material surface energy, absorption, and vertical stratification, which can then be linked to photovoltaic conversion characteristics. Through assessing the performance of temporary, artificial vertically stratified layers created by the sequential casting of the individual components to form a multilayered structure, optimal vertical stratification can be achieved. Adjusting the surface energy offset between the substrate results in donor and acceptor stabilization of that stratified layer. Further, a trade-off between the photocurrent generated in the visible region and the amount of donor or acceptor in close proximity to the electrode was observed. Modification of the substrate surface energy was achieved using self-assembled small molecules (SASM), which, in turn, directly impacted the polymer donor to acceptor ratio at the interface. Using three different donor polymers in conjunction with two alternative acceptors in an inverted organic solar cell architecture, the concentration of polymer donor molecules at the ITO (indium tin oxide)/BHJ interface could be increased relative to the acceptor. Appropriate selection of SASM facilitated a synchronized enhancement in external quantum efficiency and power conversion efficiencies over 10.5%.

The Subjective Visual Vertical and the Subjective Haptic Vertical Access Different Gravity Estimates

PubMed Central

Fraser, Lindsey E.; Makooie, Bobbak; Harris, Laurence R.

2015-01-01

The subjective visual vertical (SVV) and the subjective haptic vertical (SHV) both claim to probe the underlying perception of gravity. However, when the body is roll tilted these two measures evoke different patterns of errors with SVV generally becoming biased towards the body (A-effect, named for its discoverer, Hermann Rudolph Aubert) and SHV remaining accurate or becoming biased away from the body (E-effect, short for Entgegengesetzt-effect, meaning “opposite”, i.e., opposite to the A-effect). We compared the two methods in a series of five experiments and provide evidence that the two measures access two different but related estimates of gravitational vertical. Experiment 1 compared SVV and SHV across three levels of whole-body tilt and found that SVV showed an A-effect at larger tilts while SHV was accurate. Experiment 2 found that tilting either the head or the trunk independently produced an A-effect in SVV while SHV remained accurate when the head was tilted on an upright body but showed an A-effect when the body was tilted below an upright head. Experiment 3 repeated these head/body configurations in the presence of vestibular noise induced by using disruptive galvanic vestibular stimulation (dGVS). dGVS abolished both SVV and SHV A-effects while evoking a massive E-effect in the SHV head tilt condition. Experiments 4 and 5 show that SVV and SHV do not combine in an optimally statistical fashion, but when vibration is applied to the dorsal neck muscles, integration becomes optimal. Overall our results suggest that SVV and SHV access distinct underlying gravity percepts based primarily on head and body position information respectively, consistent with a model proposed by Clemens and colleagues. PMID:26716835

The Subjective Visual Vertical and the Subjective Haptic Vertical Access Different Gravity Estimates.

PubMed

Fraser, Lindsey E; Makooie, Bobbak; Harris, Laurence R

2015-01-01

The subjective visual vertical (SVV) and the subjective haptic vertical (SHV) both claim to probe the underlying perception of gravity. However, when the body is roll tilted these two measures evoke different patterns of errors with SVV generally becoming biased towards the body (A-effect, named for its discoverer, Hermann Rudolph Aubert) and SHV remaining accurate or becoming biased away from the body (E-effect, short for Entgegengesetzt-effect, meaning "opposite", i.e., opposite to the A-effect). We compared the two methods in a series of five experiments and provide evidence that the two measures access two different but related estimates of gravitational vertical. Experiment 1 compared SVV and SHV across three levels of whole-body tilt and found that SVV showed an A-effect at larger tilts while SHV was accurate. Experiment 2 found that tilting either the head or the trunk independently produced an A-effect in SVV while SHV remained accurate when the head was tilted on an upright body but showed an A-effect when the body was tilted below an upright head. Experiment 3 repeated these head/body configurations in the presence of vestibular noise induced by using disruptive galvanic vestibular stimulation (dGVS). dGVS abolished both SVV and SHV A-effects while evoking a massive E-effect in the SHV head tilt condition. Experiments 4 and 5 show that SVV and SHV do not combine in an optimally statistical fashion, but when vibration is applied to the dorsal neck muscles, integration becomes optimal. Overall our results suggest that SVV and SHV access distinct underlying gravity percepts based primarily on head and body position information respectively, consistent with a model proposed by Clemens and colleagues.

33 CFR 100.717 - Annual Fort Myers Beach Offshore Grand Prix; Fort Myers, FL.

Code of Federal Regulations, 2011 CFR

2011-07-01

...°58.30′ W). All coordinates referenced use datum: NAD 83. (b) Special local regulations. (1) No vessel... coordinates referenced use datum: NAD 83. (3) All vessel traffic, not involved with the Fort Myers Beach... clear of the racecourse. All coordinates referenced use datum: NAD 83. (4) All vessel traffic, not...

33 CFR 100.717 - Annual Fort Myers Beach Offshore Grand Prix; Fort Myers, FL.

Code of Federal Regulations, 2010 CFR

2010-07-01

...°58.30′ W). All coordinates referenced use datum: NAD 83. (b) Special local regulations. (1) No vessel... coordinates referenced use datum: NAD 83. (3) All vessel traffic, not involved with the Fort Myers Beach... clear of the racecourse. All coordinates referenced use datum: NAD 83. (4) All vessel traffic, not...

33 CFR 100.717 - Annual Fort Myers Beach Offshore Grand Prix; Fort Myers, FL.

Code of Federal Regulations, 2013 CFR

2013-07-01

...°58.30′ W). All coordinates referenced use datum: NAD 83. (b) Special local regulations. (1) No vessel... coordinates referenced use datum: NAD 83. (3) All vessel traffic, not involved with the Fort Myers Beach... clear of the racecourse. All coordinates referenced use datum: NAD 83. (4) All vessel traffic, not...

33 CFR 100.717 - Annual Fort Myers Beach Offshore Grand Prix; Fort Myers, FL.

Code of Federal Regulations, 2014 CFR

2014-07-01

...°58.30′ W). All coordinates referenced use datum: NAD 83. (b) Special local regulations. (1) No vessel... coordinates referenced use datum: NAD 83. (3) All vessel traffic, not involved with the Fort Myers Beach... clear of the racecourse. All coordinates referenced use datum: NAD 83. (4) All vessel traffic, not...

33 CFR 100.717 - Annual Fort Myers Beach Offshore Grand Prix; Fort Myers, FL.

Code of Federal Regulations, 2012 CFR

2012-07-01

...°58.30′ W). All coordinates referenced use datum: NAD 83. (b) Special local regulations. (1) No vessel... coordinates referenced use datum: NAD 83. (3) All vessel traffic, not involved with the Fort Myers Beach... clear of the racecourse. All coordinates referenced use datum: NAD 83. (4) All vessel traffic, not...

Impact of the reduced vertical separation minimum on the domestic United States

DOT National Transportation Integrated Search

2009-01-31

Aviation regulatory bodies have enacted the reduced vertical separation minimum standard over most of the globe. The reduced vertical separation minimum is a technique that reduces the minimum vertical separation distance between aircraft from 2000 t...

Models for extracting vertical crustal movements from leveling data

NASA Technical Reports Server (NTRS)

Holdahl, S. H.

1978-01-01

Various adjustment strategies are being used in North America to obtain vertical crustal movements from repeated leveling. The more successful models utilize polynomials or multiquadric analysis to describe elevation change with a velocity surface. Other features permit determination of nonlinear motions, motions associated with earthquakes or episodes, and vertical motions of blocks where boundaries are prespecified. The preferred models for estimating crustal motions permit the use of detached segments of releveling to govern the shape of a velocity surface and allow for input from nonleveling sources such as tide gages and paired lake gages. Some models for extracting vertical crustal movements from releveling data are also excellent for adjusting leveling networks, and permit mixing old and new data in areas exhibiting vertical motion. The new adjustment techniques are more general than older static models and will undoubtedly be used routinely in the future as the constitution of level networks becomes mainly relevelings.

Determining Coastal Mean Dynamic Topography by Geodetic Methods

NASA Astrophysics Data System (ADS)

Huang, Jianliang

2017-11-01

In geodesy, coastal mean dynamic topography (MDT) was traditionally determined by spirit leveling technique. Advances in navigation satellite positioning (e.g., GPS) and geoid determination enable space-based leveling with an accuracy of about 3 cm at tide gauges. Recent CryoSat-2, a satellite altimetry mission with synthetic aperture radar (SAR) and SAR interferometric measurements, extends the space-based leveling to the coastal ocean with the same accuracy. However, barriers remain in applying the two space-based geodetic methods for MDT determination over the coastal ocean because current geoid modeling focuses primarily on land as a substitute to spirit leveling to realize the vertical datum.

Motor mechanisms of vertical fusion in individuals with superior oblique paresis.

PubMed

Mudgil, Ananth V; Walker, Mark; Steffen, Heimo; Guyton, David L; Zee, David S

2002-06-01

We wanted to determine the mechanisms of motor vertical fusion in patients with superior oblique paresis and to correlate these mechanisms with surgical outcomes. Ten patients with superior oblique paresis underwent 3-axis, bilateral, scleral search coil eye movement recordings. Eye movements associated with fusion were analyzed. Six patients had decompensated congenital superior oblique paresis and 4 had acquired superior oblique paresis. All patients with acquired superior oblique paresis relied predominantly on the vertical rectus muscles for motor fusion. Patients with congenital superior oblique paresis were less uniform in their mechanisms for motor fusion: 2 patients used predominantly the oblique muscles, 2 patients used predominantly the vertical recti, and 2 patients used predominantly the superior oblique in the hyperdeviated eye and the superior rectus in the hypodeviated eye. The last 2 patients developed the largest changes in torsional eye alignment relative to changes in vertical eye alignment and were the only patients to develop symptomatic surgical overcorrections. There are 3 different mechanisms for vertical fusion in individuals with superior oblique paresis, with the predominant mechanism being the vertical recti. A subset of patients with superior oblique paresis uses predominantly the superior oblique muscle in the hyperdeviated paretic eye and the superior rectus muscle in the fellow eye for fusion. This results in intorsion of both eyes, causing a large change in torsional alignment. The consequent cyclodisparity, in addition to the existing vertical deviation, may make fusion difficult. The differing patterns of vertical fusional vergence may have implications for surgical treatment.

Vertical dielectric screening of few-layer van der Waals semiconductors.

PubMed

Koo, Jahyun; Gao, Shiyuan; Lee, Hoonkyung; Yang, Li

2017-10-05

Vertical dielectric screening is a fundamental parameter of few-layer van der Waals two-dimensional (2D) semiconductors. However, unlike the widely-accepted wisdom claiming that the vertical dielectric screening is sensitive to the thickness, our first-principles calculation based on the linear response theory (within the weak field limit) reveals that this screening is independent of the thickness and, in fact, it is the same as the corresponding bulk value. This conclusion is verified in a wide range of 2D paraelectric semiconductors, covering narrow-gap ones and wide-gap ones with different crystal symmetries, providing an efficient and reliable way to calculate and predict static dielectric screening of reduced-dimensional materials. Employing this conclusion, we satisfactorily explain the tunable band gap in gated 2D semiconductors. We further propose to engineer the vertical dielectric screening by changing the interlayer distance via vertical pressure or hybrid structures. Our predicted vertical dielectric screening can substantially simplify the understanding of a wide range of measurements and it is crucial for designing 2D functional devices.

Optimal viewing position in vertically and horizontally presented Japanese words.

PubMed

Kajii, N; Osaka, N

2000-11-01

In the present study, the optimal viewing position (OVP) phenomenon in Japanese Hiragana was investigated, with special reference to a comparison between the vertical and the horizontal meridians in the visual field. In the first experiment, word recognition scores were determined while the eyes were fixating predetermined locations in vertically and horizontally displayed words. Similar to what has been reported for Roman scripts, OVP curves, which were asymmetric with respect to the beginning of words, were observed in both conditions. However, this asymmetry was less pronounced for vertically than for horizontally displayed words. In the second experiment, the visibility of individual characters within strings was examined for the vertical and horizontal meridians. As for Roman characters, letter identification scores were better in the right than in the left visual field. However, identification scores did not differ between the upper and the lower sides of fixation along the vertical meridian. The results showed that the model proposed by Nazir, O'Regan, and Jacobs (1991) cannot entirely account for the OVP phenomenon. A model in which visual and lexical factors are combined is proposed instead.

Vertical pillar nanoantenna for emission enhancement and redirection

NASA Astrophysics Data System (ADS)

Paparone, J.; Laverdant, J.; Brucoli, G.; Symonds, C.; Crut, A.; Del Fatti, N.; Benoit, J. M.; Bellessa, J.

2018-01-01

Designing efficient metallic nanostructures can help in realizing bright single photon emission in the visible and near-infrared ranges. We propose a novel nanostructure design that combines the benefits of plasmonic hot spot generation in the near-field and the concept of antennas developed in the radio-frequency range. The antenna is formed by a vertical stack of metallic and dielectric nanocylinders. When used for controlling the far-field emission of a localized source, its key features are moderate losses in the metal, relatively large Purcell factors, as well as a low sensibility to the lateral position of the emitter. A redirection process necessary for these vertical structures is proposed, based on the versatility of the vertical geometry, and allows an efficient redirection of the emitted light even for antennas on dielectric substrates.

The emergence of the vertical birth in Ecuador: an analysis of agenda setting and policy windows for intercultural health

PubMed Central

Llamas, Ana; Mayhew, Susannah

2016-01-01

Maternal mortality continues to claim the lives of thousands of women in Latin America despite the availability of effective treatments to avert maternal death. In the past, efforts to acknowledge cultural diversity in birth practices had not been clearly integrated into policy. However, in Otavalo (Ecuador) a local hospital pioneered the implementation of the ‘Vertical Birth’—a practical manifestation of an intercultural health policy aimed at increasing indigenous women’s access to maternity care. Drawing on agenda-setting theory, this qualitative research explores how the vertical birth practice made it onto the local policy agenda and the processes that allowed actors to seize a window of opportunity allowing the vertical birth practice to emerge. Our results show that the processes that brought about the vertical birth practice took place over a prolonged period of time and resulted from the interplay between various factors. Firstly, a maternal health policy community involving indigenous actors played a key role in identifying maternal mortality as a policy problem, defining its causes and framing it as an indigenous rights issue. Secondly, previous initiatives to address maternal mortality provided a wealth of experience that gave these actors the knowledge and experience to formulate a feasible policy solution and consolidate support from powerful actors. Thirdly, the election of a new government that had incorporated the demands of the indigenous movement opened up a window of opportunity to push intercultural health policies such as the vertical birth. We conclude that the socioeconomic and political changes at both national and local level allowed the meaningful participation of indigenous actors that made a critical contribution to the emergence of the vertical birth practice. These findings can help us advance our knowledge of strategies to set the agenda for intercultural maternal health policy and inform future policy in similar settings

Influence of marine current on vertical migration of Pb in marine bay

NASA Astrophysics Data System (ADS)

Yu, Chen; Hong, Ai; Danfeng, Yang; Huijuan, Zhao; Dongfang, Yang

2018-02-01

This paper analyzed that vertical migration of Pb contents waters in Jiaozhou Bay, and revealed the influence of marine current on vertical migration process. Results showed that Pb contents in bottom waters of Jiaozhou Bay in April and July 1988 were 1.49-18.53 μg L-1 and 12.68/-27.64 μg L-1, respectively. The pollution level of Pb in bottom waters was moderate to heavy, and were showing temporal variations and spatial heterogeneity. The vertical migration process of Pb in April 1988 included a drifting process from the southwest to the north by means of the marine current was rapid in this region. The vertical migration process of Pb in July 1988 in the open waters included no drifting process since the flow rate of marine current was relative low in this region. The vertical migration process of Pb was jointly determined by vertical water’s effect, source input and water exchange, and the influence of marine current on the vertical migration of Pb in marine bay was significant.

Intrinsic and synaptic properties of vertical cells of the mouse dorsal cochlear nucleus

PubMed Central

Kuo, Sidney P.; Lu, Hsin-Wei

2012-01-01

Multiple classes of inhibitory interneurons shape the activity of principal neurons of the dorsal cochlear nucleus (DCN), a primary target of auditory nerve fibers in the mammalian brain stem. Feedforward inhibition mediated by glycinergic vertical cells (also termed tuberculoventral or corn cells) is thought to contribute importantly to the sound-evoked response properties of principal neurons, but the cellular and synaptic properties that determine how vertical cells function are unclear. We used transgenic mice in which glycinergic neurons express green fluorescent protein (GFP) to target vertical cells for whole cell patch-clamp recordings in acute slices of DCN. We found that vertical cells express diverse intrinsic spiking properties and could fire action potentials at high, sustained spiking rates. Using paired recordings, we directly examined synapses made by vertical cells onto fusiform cells, a primary DCN principal cell type. Vertical cell synapses produced unexpectedly small-amplitude unitary currents in fusiform cells, and additional experiments indicated that multiple vertical cells must be simultaneously active to inhibit fusiform cell spike output. Paired recordings also revealed that a major source of inhibition to vertical cells comes from other vertical cells. PMID:22572947

Proposed technique for vertical alignment of a crane's cable

NASA Technical Reports Server (NTRS)

Gera, J., Jr.

1969-01-01

Proposed vertical alignment technique senses the attitude of a cranes cable and displays any deviation from the vertical. The system consists of a detector assembly fixed to the boom and a display scope located in the cabin. It has potential application with either fixed-boom cranes or gantries.

33 CFR 100.736 - Annual Fort Myers Beach air show; Fort Myers Beach, FL.

Code of Federal Regulations, 2010 CFR

2010-07-01

...°59′15″ W. All coordinates referenced use datum: NAD 83. (2) Air Box Area. The air box area is... coordinates referenced use datum: NAD 83. (b) Special local regulations. (1) Vessels and persons are... referenced use datum: NAD 83. (c) Dates. This section will be enforced annually on the second consecutive...

Stratospheric Turbulence and Vertical Effective Diffusion Coefficients

DTIC Science & Technology

1975-09-29

UMBER AFCRL-TR-75.-0519 - 4. TILE (moiS."Eti) S. Tlr OF C RP~hT S PESO0 COVERED STRATOSPHERIC TURBULENCE AND VERTICAL EFFECTIVE DIFFUSION COEFFICIENTS...that CAT plays a prominent role in vertical transport in the stratosphere. I ~1 Unclassified t FUrs,*Tv C , Uq C ~ml .. at ’r *n he.. a* U I Department...phenomenon. Thorpe himself refers (1973) to underwater K-H as "underwater CAT." ____ ____ ____WE006 SflJGLE ( SPAD M LAVER 4" Ri" i0 15 0t (m’iJr

Sidewall containment of liquid metal with vertical alternating magnetic fields

DOEpatents

Lari, Robert J.; Praeg, Walter F.; Turner, Larry R.; Battles, James E.; Hull, John R.; Rote, Donald M.

1990-01-01

An apparatus for containing molten metal using a magnet producing vertical alternating magnetic field positioned adjacent the area in which the molten metal is to be confined. This invention can be adapted particularly to the casting of metal between counter-rotating rollers with the vertical alternating magnetic field used to confine the molten metal at the edges of the rollers. Alternately, the vertical alternating magnetic field can be used as a flow regulator in casting molten metal from an opening in a channel.

Vertically Integrated Models for Carbon Storage Modeling in Heterogeneous Domains

NASA Astrophysics Data System (ADS)

Bandilla, K.; Celia, M. A.

2017-12-01

Numerical modeling is an essential tool for studying the impacts of geologic carbon storage (GCS). Injection of carbon dioxide (CO2) into deep saline aquifers leads to multi-phase flow (injected CO2 and resident brine), which can be described by a set of three-dimensional governing equations, including mass-balance equation, volumetric flux equations (modified Darcy), and constitutive equations. This is the modeling approach on which commonly used reservoir simulators such as TOUGH2 are based. Due to the large density difference between CO2 and brine, GCS models can often be simplified by assuming buoyant segregation and integrating the three-dimensional governing equations in the vertical direction. The integration leads to a set of two-dimensional equations coupled with reconstruction operators for vertical profiles of saturation and pressure. Vertically-integrated approaches have been shown to give results of comparable quality as three-dimensional reservoir simulators when applied to realistic CO2 injection sites such as the upper sand wedge at the Sleipner site. However, vertically-integrated approaches usually rely on homogeneous properties over the thickness of a geologic layer. Here, we investigate the impact of general (vertical and horizontal) heterogeneity in intrinsic permeability, relative permeability functions, and capillary pressure functions. We consider formations involving complex fluvial deposition environments and compare the performance of vertically-integrated models to full three-dimensional models for a set of hypothetical test cases consisting of high permeability channels (streams) embedded in a low permeability background (floodplains). The domains are randomly generated assuming that stream channels can be represented by sinusoidal waves in the plan-view and by parabolas for the streams' cross-sections. Stream parameters such as width, thickness and wavelength are based on values found at the Ketzin site in Germany. Results from the

Analytical Model of Steam Chamber Evolution from Vertical Well

NASA Astrophysics Data System (ADS)

Shevchenko, D. V.; Usmanov, S. A.; Shangaraeva, A. I.; Murtaizin, T. A.

2018-05-01

This paper is aimed to check the possibility of applying the Steam Assisted Gravity Drainage in vertical wells. This challenge seems to be vital because most of the natural bitumen reservoirs are found to occur above the oil fields being developed so that a well system is already available at the stage of field management. The existing vertical wells are hard to be used for horizontal sidetracking in most of cases as the bitumen reservoir occurs at a shallow depth. The matter is to use the existing wells as vertical ones. At the same time, it is possible to drill an additional sidetrack as a producer or an injector.

Algebraic motion of vertically displacing plasmas

NASA Astrophysics Data System (ADS)

Pfefferlé, D.; Bhattacharjee, A.

2018-02-01

The vertical motion of a tokamak plasma is analytically modelled during its non-linear phase by a free-moving current-carrying rod inductively coupled to a set of fixed conducting wires or a cylindrical conducting shell. The solutions capture the leading term in a Taylor expansion of the Green's function for the interaction between the plasma column and the surrounding vacuum vessel. The plasma shape and profiles are assumed not to vary during the vertical drifting phase such that the plasma column behaves as a rigid body. In the limit of perfectly conducting structures, the plasma is prevented to come in contact with the wall due to steep effective potential barriers created by the induced Eddy currents. Resistivity in the wall allows the equilibrium point to drift towards the vessel on the slow timescale of flux penetration. The initial exponential motion of the plasma, understood as a resistive vertical instability, is succeeded by a non-linear "sinking" behaviour shown to be algebraic and decelerating. The acceleration of the plasma column often observed in experiments is thus concluded to originate from an early sharing of toroidal current between the core, the halo plasma, and the wall or from the thermal quench dynamics precipitating loss of plasma current.

Horizontal Cross Bracing Detail, Vertical Cross Bracing Detail, Horizontal Cross ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Horizontal Cross Bracing Detail, Vertical Cross Bracing Detail, Horizontal Cross Bracing Joint, Vertical Cross Bracing End Detail - Ceylon Covered Bridge, Limberlost Park, spanning Wabash River at County Road 900 South, Geneva, Adams County, IN

[The National Survey on Working Conditions: data for reflection].

PubMed

Zimmermann Verdejo, M; Maqueda Blasco, J; Almodóvar Molina, A; de la Orden Rivera, M V

1996-01-01

This work presents some data of relevance from the National Survey on Working Conditions, carried out in Spain in 1993. A cross-section survey was undertaken on a representative sample of the industry and services sectors (3,148 workers), both through an individual interview which took place at their places of work, and a questionnaire. The study revealed that preventive activities are few and far between. Only 11.8% of the companies carried out surveys into the risk of occupational accidents and/or illnesses. This datum contrasts with the high incidence among workers of exposure to the risk of accidents (59%), noise (33%) or the inhaling of chemical substances (32%). Furthermore, approximately 50% of workers spend at least a quarter of their work time in a static posture or making repetitive hand-arm movements. It is estimated that 60% are exposed to high work rates or repetitive tasks of short duration. Where the question of morbidity is concerned, 60% of workers suffer from posture problems associated with their work. In this study, a comparison is made between these findings per activity sector, together with a detailed analysis of morbidity. Finally, it should be borne in mind, that the subjectivity in the responses and answers, which is inherent to any qualitative survey, should not be regarded as a negative aspect. The way in which the worker perceives and experiences his or her work environment, provides essential information for the preventionists.

Vertically-tapered optical waveguide and optical spot transformer formed therefrom

DOEpatents

Bakke, Thor; Sullivan, Charles T.

2004-07-27

An optical waveguide is disclosed in which a section of the waveguide core is vertically tapered during formation by spin coating by controlling the width of an underlying mesa structure. The optical waveguide can be formed from spin-coatable materials such as polymers, sol-gels and spin-on glasses. The vertically-tapered waveguide section can be used to provide a vertical expansion of an optical mode of light within the optical waveguide. A laterally-tapered section can be added adjacent to the vertically-tapered section to provide for a lateral expansion of the optical mode, thereby forming an optical spot-size transformer for efficient coupling of light between the optical waveguide and a single-mode optical fiber. Such a spot-size transformer can also be added to a III-V semiconductor device by post processing.

Sidewall containment of liquid metal with vertical alternating magnetic fields

DOEpatents

Lari, R.J.; Praeg, W.F.; Turner, L.R.; Battles, J.E.; Hull, J.R.; Rote, D.M.

1990-12-04

An apparatus is disclosed for containing molten metal using a magnet producing vertical alternating magnetic field positioned adjacent the area in which the molten metal is to be confined. This invention can be adapted particularly to the casting of metal between counter-rotating rollers with the vertical alternating magnetic field used to confine the molten metal at the edges of the rollers. Alternately, the vertical alternating magnetic field can be used as a flow regulator in casting molten metal from an opening in a channel. 9 figs.

Sidewall containment of liquid metal with vertical alternating magnetic fields

DOEpatents

Lari, R.J.; Praeg, W.F.; Turner, L.R.; Battles, J.E.; Hull, J.R.; Rote, D.M.

1988-06-17

An apparatus for containing molten metal using a magnet producing vertical alternating magnetic field positioned adjacent to the area in which the molten metal is to be confined. This invention can be adapted particularly to the casting of metal between counter-rotating rollers with the vertical alternating magnetic field used to confine the molten metal at the edges of the rollers. Alternately, the vertical alternating magnetic field can be used as a flow regulator in casting molten metal from an opening in a channel. 8 figs.

Proposed U.S. Geological Survey standard for digital orthophotos

USGS Publications Warehouse

Hooper, David; Caruso, Vincent

1991-01-01

The U.S. Geological Survey has added the new category of digital orthophotos to the National Digital Cartographic Data Base. This differentially rectified digital image product enables users to take advantage of the properties of current photoimagery as a source of geographic information. The product and accompanying standard were implemented in spring 1991. The digital orthophotos will be quadrangle based and cast on the Universal Transverse Mercator projection and will extend beyond the 3.75-minute or 7.5-minute quadrangle area at least 300 meters to form a rectangle. The overedge may be used for mosaicking with adjacent digital orthophotos. To provide maximum information content and utility to the user, metadata (header) records exist at the beginning of the digital orthophoto file. Header information includes the photographic source type, date, instrumentation used to create the digital orthophoto, and information relating to the DEM that was used in the rectification process. Additional header information is included on transformation constants from the 1927 and 1983 North American Datums to the orthophoto internal file coordinates to enable the user to register overlays on either datum. The quadrangle corners in both datums are also imprinted on the image. Flexibility has been built into the digital orthophoto format for future enhancements, such as the provision to include the corresponding digital elevation model elevations used to rectify the orthophoto. The digital orthophoto conforms to National Map Accuracy Standards and provides valuable mapping data that can be used as a tool for timely revision of standard map products, for land use and land cover studies, and as a digital layer in a geographic information system.

Effects of Vertical Direction and Aperture Size on the Perception of Visual Acceleration.

PubMed

Mueller, Alexandra S; González, Esther G; McNorgan, Chris; Steinbach, Martin J; Timney, Brian

2016-02-06

It is not well understood whether the distance over which moving stimuli are visible affects our sensitivity to the presence of acceleration or our ability to track such stimuli. It is also uncertain whether our experience with gravity creates anisotropies in how we detect vertical acceleration and deceleration. To address these questions, we varied the vertical extent of the aperture through which we presented vertically accelerating and decelerating random dot arrays. We hypothesized that observers would better detect and pursue accelerating and decelerating stimuli that extend over larger than smaller distances. In Experiment 1, we tested the effects of vertical direction and aperture size on acceleration and deceleration detection accuracy. Results indicated that detection is better for downward motion and for large apertures, but there is no difference between vertical acceleration and deceleration detection. A control experiment revealed that our manipulation of vertical aperture size affects the ability to track vertical motion. Smooth pursuit is better (i.e., with higher peak velocities) for large apertures than for small apertures. Our findings suggest that the ability to detect vertical acceleration and deceleration varies as a function of the direction and vertical extent over which an observer can track the moving stimulus. © The Author(s) 2016.

Vertical nanopillars for highly localized fluorescence imaging

PubMed Central

Xie, Chong; Hanson, Lindsey; Cui, Yi; Cui, Bianxiao

2011-01-01

Observing individual molecules in a complex environment by fluorescence microscopy is becoming increasingly important in biological and medical research, for which critical reduction of observation volume is required. Here, we demonstrate the use of vertically aligned silicon dioxide nanopillars to achieve below-the-diffraction-limit observation volume in vitro and inside live cells. With a diameter much smaller than the wavelength of visible light, a transparent silicon dioxide nanopillar embedded in a nontransparent substrate restricts the propagation of light and affords evanescence wave excitation along its vertical surface. This effect creates highly confined illumination volume that selectively excites fluorescence molecules in the vicinity of the nanopillar. We show that this nanopillar illumination can be used for in vitro single-molecule detection at high fluorophore concentrations. In addition, we demonstrate that vertical nanopillars interface tightly with live cells and function as highly localized light sources inside the cell. Furthermore, specific chemical modification of the nanopillar surface makes it possible to locally recruit proteins of interest and simultaneously observe their behavior within the complex, crowded environment of the cell. PMID:21368157

Vertical Motion Characteristics of Tropical Cyclones Determined with Airborne Doppler Radial Velocities.

NASA Astrophysics Data System (ADS)

Black, Micheal L.; Burpee, Robert W.; Marks, Frank D., Jr.

1996-07-01

Vertical motions in seven Atlantic hurricanes are determined from data recorded by Doppler radars on research aircraft. The database consists of Doppler velocities and reflectivities from vertically pointing radar rays collected along radial flight legs through the hurricane centers. The vertical motions are estimated throughout the depth of the troposphere from the Doppler velocities and bulk estimates of particle fallspeeds.Portions of the flight tracks are subjectively divided into eyewall, rainband, stratiform, and `other' regions. Characteristics of the vertical velocity and radar structure are described as a function of altitude for the entire dataset and each of the four regions. In all of the regions, more than 70% of the vertical velocities range from 2 to 2 m s1. The broadest distribution of vertical motion is in the eyewall region where 5% of the vertical motions are >5 m s1. Averaged over the entire dataset, the mean vertical velocity is upward at all altitudes. Mean downward motion occurs only in the lower troposphere of the stratiform region. Significant vertical variations in the mean profiles of vertical velocity and reflectivity are discussed and related to microphysical processes.In the lower and middle troposphere, the characteristics of the Doppler-derived vertical motions are similar to those described in an earlier study using flight-level vertical velocities, even though the horizontal resolution of the Doppler data is 750 m compared to 125 m from the in situ flight-level measurements. The Doppler data are available at higher altitudes than those reached by turboprop aircraft and provide information on vertical as well as horizontal variations. In a vertical plane along the radial flight tracks, Doppler up- and downdrafts are defined at each 300-m altitude interval as vertical velocities whose absolute values continuously exceed 1.5 m s1, with at least one speed having an absolute value greater than 3.0 m s1. The properties of the Doppler

Temporal Variability in Vertical Groundwater Fluxes and the Effect of Solar Radiation on Streambed Temperatures Based on Vertical High Resolution Distributed Temperature Sensing

NASA Astrophysics Data System (ADS)

Sebok, E.; Karan, S.; Engesgaard, P. K.; Duque, C.

2013-12-01

Due to its large spatial and temporal variability, groundwater discharge to streams is difficult to quantify. Methods using vertical streambed temperature profiles to estimate vertical fluxes are often of coarse vertical spatial resolution and neglect to account for the natural heterogeneity in thermal conductivity of streambed sediments. Here we report on a field investigation in a stream, where air, stream water and streambed sediment temperatures were measured by Distributed Temperature Sensing (DTS) with high spatial resolution to; (i) detect spatial and temporal variability in groundwater discharge based on vertical streambed temperature profiles, (ii) study the thermal regime of streambed sediments exposed to different solar radiation influence, (iii) describe the effect of solar radiation on the measured streambed temperatures. The study was carried out at a field site located along Holtum stream, in Western Denmark. The 3 m wide stream has a sandy streambed with a cobbled armour layer, a mean discharge of 200 l/s and a mean depth of 0.3 m. Streambed temperatures were measured with a high-resolution DTS system (HR-DTS). By helically wrapping the fiber optic cable around two PVC pipes of 0.05 m and 0.075 m outer diameter over 1.5 m length, temperature measurements were recorded with 5.7 mm and 3.8 mm vertical spacing, respectively. The HR-DTS systems were installed 0.7 m deep in the streambed sediments, crossing both the sediment-water and the water-air interface, thus yielding high resolution water and air temperature data as well. One of the HR-DTS systems was installed in the open stream channel with only topographical shading, while the other HR-DTS system was placed 7 m upstream, under the canopy of a tree, thus representing the shaded conditions with reduced influence of solar radiation. Temperature measurements were taken with 30 min intervals between 16 April and 25 June 2013. The thermal conductivity of streambed sediments was calibrated in a 1D flow

Pressure as a limit to bloater (Coregonus hoyi) vertical migration

USGS Publications Warehouse

TeWinkel, Leslie M.; Fleischer, Guy W.

1998-01-01

Observations of bloater vertical migration showed a limit to the vertical depth changes that bloater experience. In this paper, we conducted an analysis of maximum differences in pressure encountered by bloater during vertical migration. Throughout the bottom depths studied, bloater experienced maximum reductions in swim bladder volume equal to approximately 50-60% of the volume in midwater. The analysis indicated that the limit in vertical depth change may be related to a maximum level of positive or negative buoyancy for which bloater can compensate using alternative mechanisms such as hydrodynamic lift. Bloater may be limited in the extent of migration by either their depth of neutral buoyancy or the distance above the depth of neutral buoyancy at which they can still maintain their position in the water column. Although a migration limit for the bloater population was evident, individual distances of migration varied at each site. These variations in migration distances may indicate differences in depths of neutral buoyancy within the population. However, in spite of these variations, the strong correlation between shallowest depths of migration and swim bladder volume reduction across depths provides evidence that hydrostatic pressure limits the extent of daily vertical movement in bloater.

Observations of and Influences on Low-Latitude Vertical Plasma Drifts

NASA Astrophysics Data System (ADS)

Miller, E. S.; Chartier, A.; Paxton, L. J.

2016-12-01

Many workers have suggested that the morphology (position and relative intensities) of the crests of the equatorial ionization anomaliesis related to the time history of the equatorial vertical drift. In this work, we compare observations of the vertical drift using an HF radiosignals of opportunity in the Central Pacific with UV 135.6-nm observations of the equatorial anomalies from the DMSP/SSUSI andTIMED/GUVI instruments. Furthermore, we explore the role of E region density in modulating the vertical plasma drift using a passive HFsounding experiment in the Caribbean. Coupling between nighttime medium-scale traveling ionospheric disturbances (MSTIDs) and sporadic-Elayers has been suggested as a growth-rate-increasing process. While we observe sporadic-E in the local hemisphere coincident to increases in thealtitude of the F-region altitude, we also observe uplifts without sporadic-E in the local hemisphere. Apart from the trivial explanation that sporadic-E is occurring in the conjugate hemisphere, another possible explanation is that the E region may enhance the vertical drift, but is not required to produce enhanced vertical drifts. These studies represent fruitful areas of future intersection between ground-based observations and ICON and GOLD science.

Gate-Tunable Spin Transport and Giant Electroresistance in Ferromagnetic Graphene Vertical Heterostructures

PubMed Central

Myoung, Nojoon; Park, Hee Chul; Lee, Seung Joo

2016-01-01

Controlling tunneling properties through graphene vertical heterostructures provides advantages in achieving large conductance modulation which has been known as limitation in lateral graphene device structures. Despite of intensive research on graphene vertical heterosturctures for recent years, the potential of spintronics based on graphene vertical heterostructures remains relatively unexplored. Here, we present an analytical device model for graphene-based spintronics by using ferromagnetic graphene in vertical heterostructures. We consider a normal or ferroelectric insulator as a tunneling layer. The device concept yields a way of controlling spin transport through the vertical heterostructures, resulting in gate-tunable spin-switching phenomena. Also, we revealed that a ‘giant’ resistance emerges through a ferroelectric insulating layer owing to the anti-parallel configuration of ferromagnetic graphene layers by means of electric fields via gate and bias voltages. Our findings discover the prospect of manipulating the spin transport properties in vertical heterostructures without use of magnetic fields. PMID:27126101

[EEG-markers of vertical postural organization in healthy persons].

PubMed

Zhavoronkova, L A; Zharikova, A V; Kushnir, E M; Mikhalkova, A A

2012-01-01

In 10 healthy persons (22.8 +/- 0.67 years) spectral-coherence parameters of EEG were analyzed in different steps of verticalizations--from gorizontal position to seat and stand one. Maximal changes of all EEG parameters were observed in state with absence of visual control. We observed an increase of power for fast spectral bands of EEG (beta- and gamma-bands) in all conditions and additional increase of these EEG parameters was observed at situation of complication of conditions of vertical pose supporting. Results of EEG coherent analysis in conditions of human verticalization showed specific increase of coherence for the majority of rhythm ranges in the right hemisphere especially in the central-frontal and in occipital-parietal areas and for interhemispheric pairs for these leads. This fact can reflect participation of cortical as well as subcortical structures in these processes. In conditions of complicate conditions of vertical pose supporting the additional increase of EEG coherence in fast bands (beta-rhythm) was observed at the frontal areas. This fact can testify about increasing of executive functions in this conditions.

Graphene and PbS quantum dot hybrid vertical phototransistor

NASA Astrophysics Data System (ADS)

Song, Xiaoxian; Zhang, Yating; Zhang, Haiting; Yu, Yu; Cao, Mingxuan; Che, Yongli; Dai, Haitao; Yang, Junbo; Ding, Xin; Yao, Jianquan

2017-04-01

A field-effect phototransistor based on a graphene and lead sulfide quantum dot (PbS QD) hybrid in which PbS QDs are embedded in a graphene matrix has been fabricated with a vertical architecture through a solution process. The n-type Si/SiO2 substrate (gate), Au/Ag nanowire transparent source electrode, active layer and Au drain electrode are vertically stacked in the device, which has a downscaled channel length of 250 nm. Photoinduced electrons in the PbS QDs leap into the conduction band and fill in the trap states, while the photoinduced holes left in the valence band transfer to the graphene and form the photocurrent under biases from which the photoconductive gain is evaluated. The graphene/QD-based vertical phototransistor shows a photoresponsivity of 2 × 103 A W-1, and specific detectivity up to 7 × 1012 Jones under 808 nm laser illumination with a light irradiance of 12 mW cm-2. The solution-processed vertical phototransistor provides a new facile method for optoelectronic device applications.

Weather Research and Forecasting Model with Vertical Nesting Capability

DOE Office of Scientific and Technical Information (OSTI.GOV)

2014-08-01

The Weather Research and Forecasting (WRF) model with vertical nesting capability is an extension of the WRF model, which is available in the public domain, from www.wrf-model.org. The new code modifies the nesting procedure, which passes lateral boundary conditions between computational domains in the WRF model. Previously, the same vertical grid was required on all domains, while the new code allows different vertical grids to be used on concurrently run domains. This new functionality improves WRF's ability to produce high-resolution simulations of the atmosphere by allowing a wider range of scales to be efficiently resolved and more accurate lateral boundarymore » conditions to be provided through the nesting procedure.« less

A local-circulation model for Darrieus vertical-axis wind turbines

NASA Astrophysics Data System (ADS)

Masse, B.

1986-04-01

A new computational model for the aerodynamics of the vertical-axis wind turbine is presented. Based on the local-circulation method generalized for curved blades, combined with a wake model for the vertical-axis wind turbine, it differs markedly from current models based on variations in the streamtube momentum and vortex models using the lifting-line theory. A computer code has been developed to calculate the loads and performance of the Darrieus vertical-axis wind turbine. The results show good agreement with experimental data and compare well with other methods.

DETAIL OF VERTICAL AT PANEL OVER PIER C, SHOWING DECK, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

DETAIL OF VERTICAL AT PANEL OVER PIER C, SHOWING DECK, GUARDRAIL, VERTICAL AND UPPER CHORD, VIEW TO NORTHEAST. - Blue Water Bridge, Spanning St. Clair River at I-69, I-94, & Canadian Route 402, Port Huron, St. Clair County, MI

STEADY-STATE DESIGN OF VERTICAL WELLS FOR LIQUIDS ADDITION AT BIOREACTOR LANDFILLS

EPA Science Inventory

This paper presents design charts that a landfill engineer can use for the design of a vertical well system for liquids addition at bioreactor landfills. The flow rate and lateral and vertical zones of impact of a vertical well were estimated as a function of input variables su...

Arthropod vertical stratification in temperate deciduous forests: Implications for conservation oriented management

Treesearch

Ulyshen Michael

2011-01-01

Studies on the vertical distribution patterns of arthropods in temperate deciduous forests reveal highly stratified (i.e., unevenly vertically distributed) communities. These patterns are determined by multiple factors acting simultaneously, including: (1) time (forest age, season, time of day); (2) forest structure (height, vertical foliage complexity, plant surface...

The Subjective Visual Vertical: Validation of a Simple Test

ERIC Educational Resources Information Center

Tesio, Luigi; Longo, Stefano; Rota, Viviana

2011-01-01

The study sought to provide norms for a simple test of visual perception of verticality (subjective visual vertical). The study was designed as a cohort study with a balanced design. The setting was the Rehabilitation Department of a University Hospital. Twenty-two healthy adults, of 23-58 years, 11 men (three left handed) and 11 women (three left…

Characterization of Nonlinear Effects in Optically Pumped Vertical Cavity Surface Emitting Lasers

DTIC Science & Technology

1993-12-01

Vertical Cavity Surface Emitting Lasers ( VCSELs ) are an exciting...lines A-3 X AFIT/GEOiENP/93 D-01 Abstract The nonlinear characteristics of optically pumped Vertical Cavity Surface Emitting Lasers ( VCSELs ) are...uniformity of the VCSEL fabrication. xi Characterization of Nonlinear Effects in Optically Pumped Vertical Cavity Surface Emitting Lasers

77 FR 13232 - Security Zones; G8/North Atlantic Treaty Organization (NATO) Summit, Chicago, IL

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-06

... point located in the approximate position 41[deg]51'37'' N, 087[deg]36'44'' W. [DATUM: NAD 83]. (2... located in the approximate position 41[deg]53'19'' N, 087[deg]36'17'' W. [DATUM: NAD 83]. (3) Security..., 087[deg]36'28'' W. [DATUM: NAD 83] and the juncture of the north and south branches of the Chicago...

Evaluation of vector coastline features extracted from 'structure from motion'-derived elevation data

USGS Publications Warehouse

Kinsman, Nicole; Gibbs, Ann E.; Nolan, Matt

2015-01-01

For extensive and remote coastlines, the absence of high-quality elevation models—for example, those produced with lidar—leaves some coastal populations lacking one of the essential elements for mapping shoreline positions or flood extents. Here, we compare seven different elevation products in a lowlying area in western Alaska to establish their appropriateness for coastal mapping applications that require the delineation of elevation-based vectors. We further investigate the effective use of a Structure from Motion (SfM)-derived surface model (vertical RMSE<20 cm) by generating a tidal datum-based shoreline and an inundation extent map for a 2011 flood event. Our results suggest that SfM-derived elevation products can yield elevation-based vector features that have horizontal positional uncertainties comparable to those derived from other techniques. We also provide a rule-of-thumb equation to aid in the selection of minimum elevation model specifications based on terrain slope, vertical uncertainties, and desired horizontal accuracy.

Market and organizational factors associated with hospital vertical integration into sub-acute care.

PubMed

Hogan, Tory H; Lemak, Christy Harris; Hearld, Larry R; Sen, Bisakha P; Wheeler, Jack R C; Menachemi, Nir

2018-04-11

Changes in payment models incentivize hospitals to vertically integrate into sub-acute care (SAC) services. Through vertical integration into SAC, hospitals have the potential to reduce the transaction costs associated with moving patients throughout the care continuum and reduce the likelihood that patients will be readmitted. The purpose of this study is to examine the correlates of hospital vertical integration into SAC. Using panel data of U.S. acute care hospitals (2008-2012), we conducted logit regression models to examine environmental and organizational factors associated with hospital vertical integration. Results are reported as average marginal effects. Among 3,775 unique hospitals (16,269 hospital-year observations), 25.7% vertically integrated into skilled nursing facilities during at least 1 year of the study period. One measure of complexity, the availability of skilled nursing facilities in a county (ME = -1.780, p < .001), was negatively associated with hospital vertical integration into SAC. Measures of munificence, percentage of the county population eligible for Medicare (ME = 0.018, p < .001) and rural geographic location (ME = 0.069, p < .001), were positively associated with hospital vertical integration into SAC. Dynamism, when measured as the change county population between 2008 and 2011 (ME = 1.19e-06, p < .001), was positively associated with hospital vertical integration into SAC. Organizational resources, when measured as swing beds (ME = 0.069, p < .001), were positively associated with hospital vertical integration into SAC. Organizational resources, when measured as investor owned (ME = -0.052, p < .1) and system affiliation (ME = -0.041, p < .1), were negatively associated with hospital vertical integration into SAC. Hospital adaption to the changing health care landscape through vertical integration varies across market and organizational conditions. Current Centers for Medicare and Medicaid reimbursement programs do not take

Algebraic motion of vertically displacing plasmas

DOE PAGES

Pfefferle, D.; Bhattacharjee, A.

2018-02-27

In this paper, the vertical motion of a tokamak plasma is analytically modelled during its non-linear phase by a free-moving current-carrying rod inductively coupled to a set of fixed conducting wires or a cylindrical conducting shell. The solutions capture the leading term in a Taylor expansion of the Green's function for the interaction between the plasma column and the surrounding vacuum vessel. The plasma shape and profiles are assumed not to vary during the vertical drifting phase such that the plasma column behaves as a rigid body. In the limit of perfectly conducting structures, the plasma is prevented to comemore » in contact with the wall due to steep effective potential barriers created by the induced Eddy currents. Resistivity in the wall allows the equilibrium point to drift towards the vessel on the slow timescale of flux penetration. The initial exponential motion of the plasma, understood as a resistive vertical instability, is succeeded by a non-linear “sinking” behaviour shown to be algebraic and decelerating. Finally, the acceleration of the plasma column often observed in experiments is thus concluded to originate from an early sharing of toroidal current between the core, the halo plasma, and the wall or from the thermal quench dynamics precipitating loss of plasma current.« less

Algebraic motion of vertically displacing plasmas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pfefferle, D.; Bhattacharjee, A.

In this paper, the vertical motion of a tokamak plasma is analytically modelled during its non-linear phase by a free-moving current-carrying rod inductively coupled to a set of fixed conducting wires or a cylindrical conducting shell. The solutions capture the leading term in a Taylor expansion of the Green's function for the interaction between the plasma column and the surrounding vacuum vessel. The plasma shape and profiles are assumed not to vary during the vertical drifting phase such that the plasma column behaves as a rigid body. In the limit of perfectly conducting structures, the plasma is prevented to comemore » in contact with the wall due to steep effective potential barriers created by the induced Eddy currents. Resistivity in the wall allows the equilibrium point to drift towards the vessel on the slow timescale of flux penetration. The initial exponential motion of the plasma, understood as a resistive vertical instability, is succeeded by a non-linear “sinking” behaviour shown to be algebraic and decelerating. Finally, the acceleration of the plasma column often observed in experiments is thus concluded to originate from an early sharing of toroidal current between the core, the halo plasma, and the wall or from the thermal quench dynamics precipitating loss of plasma current.« less

Interrelationships among Vertical and Horizontal Collectivism, Modesty, and Self-Enhancement.

ERIC Educational Resources Information Center

Kurman, Jenny; Sriram, N.

2002-01-01

Investigated the relationship among self-enhancement, modesty, and vertical and horizontal collectivism-individualism, surveying high school students from Singapore, urban Israel, and Israeli kibbutzes. Modesty was highest and self-enhancement lowest among Singaporeans. Modesty related positively to vertical collectivism and negatively to…

A New Method of Providing Communities With High-Resolution Maps of Present and Future Inundation Pathways: Two Examples From Massachusetts

NASA Astrophysics Data System (ADS)

Borrelli, M.; Mague, S. T.; Smith, T. L.

2015-12-01

A new method of mapping storm-tide (inundation) pathways and linking those data with tidal elevations in real-time for local managers is being developed. Separate, ongoing studies in two coastal towns in Massachusetts have demonstrated the strengths of this method. High-resolution lidar datasets are imported into 3D data visualization software and water levels are raised incrementally from the highest spring tide of the year to the storm of record +1 m. This range was identified to include 'nuisance flooding' as well as present and future inundation pathways not yet observed by local authorities caused by storms superimposed on projected sea level rise. Potential storm-tide pathways are identified using Lidar data but are then verified with extensive fieldwork using RTK-GPS instruments (tested vertical accuracy of 4.9 cm at 95%) to overcome the vertical uncertainty associated with Lidar data. The fieldwork serves two purposes, first is to field check the lidar data with the highest resolution instrument available and, second to verify and document the presence or absence of a storm-tide pathway. Having developed the map of storm tide pathways within a GIS environment referenced to a geodetic datum (NAVD88), a tide gauge or staff is installed in the town's harbor or other sheltered coastal area and the elevations of all storm tide pathways are then referenced to the local tidal datum. The benefit here is three-fold. First, local officials can use the high-resolution data set that is tied to a local tidal datum to autonomously monitor predicted storm surges and be prepared for inundation at sites prior to flooding. Second, storm-tide pathways that have heretofore never been inundated can be identified and steps can be taken to remove or minimize flooding hazards. Finally, identification of present and future storm tide pathways can be used to prioritize and budget proactive solutions in response to increases in chronic, nuisance and more frequent flooding associated

Juno at the Vertical Integration Facility

NASA Image and Video Library

2011-08-03

At Space Launch Complex 41, the Juno spacecraft, enclosed in an Atlas payload fairing, was transferred into the Vertical Integration Facility where it was positioned on top of the Atlas rocket stacked inside.

Application of a new vertical profiling tool (ESASS) for sampling groundwater quality during hollow-stem auger drilling

USGS Publications Warehouse

Harte, P.T.; Flanagan, S.M.

2011-01-01

A new tool called ESASS (Enhanced Screen Auger Sampling System) was developed by the U.S. Geological Survey. The use of ESASS, because of its unique U.S. patent design (U.S. patent no. 7,631,705 B1), allows for the collection of representative, depth-specific groundwater samples (vertical profiling) in a quick and efficient manner using a 0.305-m long screen auger during hollow-stem auger drilling. With ESASS, the water column in the flights above the screen auger is separated from the water in the screen auger by a specially designed removable plug and collar. The tool fits inside an auger of standard inner diameter (82.55 mm). The novel design of the system constituted by the plug, collar, and A-rod allows the plug to be retrieved using conventional drilling A-rods. After retrieval, standard-diameter (50.8 mm) observation wells can be installed within the hollow-stem augers. Testing of ESASS was conducted at one waste-disposal site with tetrachloroethylene (PCE) contamination and at two reference sites with no known waste-disposal history. All three sites have similar geology and are underlain by glacial, stratified-drift deposits. For the applications tested, ESASS proved to be a useful tool in vertical profiling of groundwater quality. At the waste site, PCE concentrations measured with ESASS profiling at several depths were comparable (relative percent difference <25%) to PCE concentrations sampled from wells. Vertical profiling with ESASS at the reference sites illustrated the vertical resolution achievable in the profile system; shallow groundwater quality varied by a factor of five in concentration of some constituents (nitrate and nitrite) over short (0.61 m) distances. Ground Water Monitoring & Remediation ?? 2011, National Ground Water Association. No claim to original US government works.

Vertical Photon Transport in Cloud Remote Sensing Problems

NASA Technical Reports Server (NTRS)

Platnick, S.

1999-01-01

Photon transport in plane-parallel, vertically inhomogeneous clouds is investigated and applied to cloud remote sensing techniques that use solar reflectance or transmittance measurements for retrieving droplet effective radius. Transport is couched in terms of weighting functions which approximate the relative contribution of individual layers to the overall retrieval. Two vertical weightings are investigated, including one based on the average number of scatterings encountered by reflected and transmitted photons in any given layer. A simpler vertical weighting based on the maximum penetration of reflected photons proves useful for solar reflectance measurements. These weighting functions are highly dependent on droplet absorption and solar/viewing geometry. A superposition technique, using adding/doubling radiative transfer procedures, is derived to accurately determine both weightings, avoiding time consuming Monte Carlo methods. Superposition calculations are made for a variety of geometries and cloud models, and selected results are compared with Monte Carlo calculations. Effective radius retrievals from modeled vertically inhomogeneous liquid water clouds are then made using the standard near-infrared bands, and compared with size estimates based on the proposed weighting functions. Agreement between the two methods is generally within several tenths of a micrometer, much better than expected retrieval accuracy. Though the emphasis is on photon transport in clouds, the derived weightings can be applied to any multiple scattering plane-parallel radiative transfer problem, including arbitrary combinations of cloud, aerosol, and gas layers.

Contemporary Surface Seasonal Oscillation and Vertical Deformation in Tibetan Plateau and Nepal Derived from the GPS, Leveling and GRACE Data

NASA Astrophysics Data System (ADS)

Shen, W.; Pan, Y.; Hwang, C.; Ding, H.

2015-12-01

We use 168 Continuous Global Positioning System (CGPS) stations distributed in the Tibetan Plateau (TP) and Nepal from lengths of 2.5 to 14 years to estimate the present-day velocity field in this area, including the horizontal and vertical deformations under the frame ITRF2008. We estimate and remove common mode errors in regional GPS time series using the principal component analysis (PCA), obtaining a time series with high signal to noise ratio. Following the maximum estimation analysis, a power law plus white noise stochastic model are adopted to estimate the velocity field. The highlight of Tibetan region is the crust vertical deformation. GPS vertical time series present seasonal oscillations caused by temporal mass loads, hence GRACE data from CSR are used to study the mass loads change. After removing the mass load deformations from GPS vertical rates, the results are improved. Leveling data about 48 years in this region are also used to estimate the rates of vertical movements. Our study suggests that the boundary of south Nepal is still sinking due to the fact that the India plate is crashing into the Eurasian plate. The uplift rates from south to north of TP reduce gradually. Himalayas region and north Nepal uplift around 6 mm/yr in average. The uplift rate along East TP in Qinhai is around 2.7 mm/yr in average. In contrast, the southeast of Tibetan Plateau, south Yunnan and Tarim in Xinjiang sink with different magnitudes. Our observation results suggest complicated mechanism of the mass migration in TP. This study is supported by National 973 Project China (grant Nos. 2013CB733302 and 2013CB733305), NSFC (grant Nos. 41174011, 41429401, 41210006, 41128003, 41021061).

Influence of loading forces on the vertical accuracy of interocclusal records.

PubMed

Ghazal, Muhamad; Kern, Matthias

2010-02-01

To evaluate the influence of loading forces on the vertical discrepancies caused by interocclusal recording materials. A custom-made apparatus was used to simulate the maxilla and mandible. Eight interocclusal records were made in each of the following groups: G1-Aluwax (aluminum wax; Aluwax), G2-Beauty Pink wax (hydrocarbon wax compound; Miltex), G3-Futar D, G4-Futar D Fast, G5-Futar Scan (polyvinyl siloxanes; Kettenbach), and G6-Ramitec (polyether; 3M ESPE). The vertical discrepancies were measured by an inductive displacement transducer connected to a carrier frequency amplifier after storage of the records for 1 hour at room temperature. Different compressive loading forces up to 1 kg were applied onto the upper part of the apparatus to evaluate the influence on the vertical discrepancies of the records. Two-way ANOVA was used for statistical analysis. The compressive loading force had a statistically significant influence on the vertical discrepancies (P<.01) (ie, higher forces reduced the vertical discrepancies). When a compressive force of 1 kg was applied to the upper part of the apparatus, the mean vertical discrepancies for G1 (11+/-3 microm) and G2 (12+/-3 microm) were statistically significantly higher than in groups G3 (1+/-1 microm), G4 (2+/-1 microm), G5 (0+/-1 microm), and G6 (-2+/-2 microm). A compressive force of 1 kg could be used to stabilize the cast during mounting procedures in an articulator using an interocclusal record made of polyvinyl siloxane without vertically changing the interocclusal relationships.

Trauma of the upper cervical spine: focus on vertical atlantoaxial dislocation.

PubMed

Pissonnier, M L; Lazennec, J Y; Renoux, J; Rousseau, M A

2013-10-01

Traumatic ligament injuries of the craniovertebral junction, either isolated or associated with bone avulsion or fracture, often lead to death. These injuries are rare and underrated but are increasingly seen in emergency departments due to the improvement in initial on-scene management of accidents. Vertical atlantoaxial dislocation (AAD) is a specific lesion that was barely reported. Based on our experience, our goal was to systematically investigate the prevalence and prognosis of traumatic vertical AAD and discuss its management. All cervical CT scans performed at our institution between 2006 and 2010 for cervical trauma in adults were retrospectively reviewed. Based on the measurement of lateral mass index (LMI), defined as the gap between C1 and C2 articular facets, we identified three cases of traumatic vertical AAD in 300 CT scans. Their medical records were investigated. The incidence of vertical AAD was 1% in the exposed population. One case was an isolated vertical AAD and two were associated with a type II odontoid fracture. We report the first case in the literature of unilateral vertical AAD. Two patients died rapidly; the survivor was treated with occipitocervical fixation. Specific maneuvers were used for immobilization and reduction. This study found a not insignificant incidence of vertical AAD and a high lethality rate. LMI appears to be a relevant radiological criterion for this diagnosis, for which traction is contraindicated. Associated neurological or vascular damage should be suspected and investigated. In our experience, spinal surgical fixation is required because of major instability.

Minimizing center of mass vertical movement increases metabolic cost in walking.

PubMed

Ortega, Justus D; Farley, Claire T

2005-12-01

A human walker vaults up and over each stance limb like an inverted pendulum. This similarity suggests that the vertical motion of a walker's center of mass reduces metabolic cost by providing a mechanism for pendulum-like mechanical energy exchange. Alternatively, some researchers have hypothesized that minimizing vertical movements of the center of mass during walking minimizes the metabolic cost, and this view remains prevalent in clinical gait analysis. We examined the relationship between vertical movement and metabolic cost by having human subjects walk normally and with minimal center of mass vertical movement ("flat-trajectory walking"). In flat-trajectory walking, subjects reduced center of mass vertical displacement by an average of 69% (P = 0.0001) but consumed approximately twice as much metabolic energy over a range of speeds (0.7-1.8 m/s) (P = 0.0001). In flat-trajectory walking, passive pendulum-like mechanical energy exchange provided only a small portion of the energy required to accelerate the center of mass because gravitational potential energy fluctuated minimally. Thus, despite the smaller vertical movements in flat-trajectory walking, the net external mechanical work needed to move the center of mass was similar in both types of walking (P = 0.73). Subjects walked with more flexed stance limbs in flat-trajectory walking (P < 0.001), and the resultant increase in stance limb force generation likely helped cause the doubling in metabolic cost compared with normal walking. Regardless of the cause, these findings clearly demonstrate that human walkers consume substantially more metabolic energy when they minimize vertical motion.

Kinetic energy spectra, vertical resolution and dissipation in high-resolution atmospheric simulations.

NASA Astrophysics Data System (ADS)

Skamarock, W. C.

2017-12-01

We have performed week-long full-physics simulations with the MPAS global model at 15 km cell spacing using vertical mesh spacings of 800, 400, 200 and 100 meters in the mid-troposphere through the mid-stratosphere. We find that the horizontal kinetic energy spectra in the upper troposphere and stratosphere does not converge with increasing vertical resolution until we reach 200 meter level spacing. Examination of the solutions indicates that significant inertia-gravity waves are not vertically resolved at the lower vertical resolutions. Diagnostics from the simulations indicate that the primary kinetic energy dissipation results from the vertical mixing within the PBL parameterization and from the gravity-wave drag parameterization, with smaller but significant contributions from damping in the vertical transport scheme and from the horizontal filters in the dynamical core. Most of the kinetic energy dissipation in the free atmosphere occurs within breaking mid-latitude baroclinic waves. We will briefly review these results and their implications for atmospheric model configuration and for atmospheric dynamics, specifically that related to the dynamics associated with the mesoscale kinetic energy spectrum.

Removing the Interdependency between Horizontal and Vertical Eye-Movement Components in Electrooculograms

PubMed Central

Chang, Won-Du; Cha, Ho-Seung; Im, Chang-Hwan

2016-01-01

This paper introduces a method to remove the unwanted interdependency between vertical and horizontal eye-movement components in electrooculograms (EOGs). EOGs have been widely used to estimate eye movements without a camera in a variety of human-computer interaction (HCI) applications using pairs of electrodes generally attached either above and below the eye (vertical EOG) or to the left and right of the eyes (horizontal EOG). It has been well documented that the vertical EOG component has less stability than the horizontal EOG one, making accurate estimation of the vertical location of the eyes difficult. To address this issue, an experiment was designed in which ten subjects participated. Visual inspection of the recorded EOG signals showed that the vertical EOG component is highly influenced by horizontal eye movements, whereas the horizontal EOG is rarely affected by vertical eye movements. Moreover, the results showed that this interdependency could be effectively removed by introducing an individual constant value. It is therefore expected that the proposed method can enhance the overall performance of practical EOG-based eye-tracking systems. PMID:26907271

Assessment of the perception of verticality and horizontality with self-paced saccades.

PubMed

Pettorossi, V E; Bambagioni, D; Bronstein, A M; Gresty, M A

1998-07-01

We investigated the ability of human subjects (Ss) to make self-paced saccades in the earth-vertical and horizontal directions (space-referenced task) and in the direction of the head-vertical and horizontal axis (self-referenced task) during whole body tilts of 0 degrees, 22.5 degrees, 45 degrees and 90 degrees in the frontal (roll) plane. Saccades were recorded in the dark with computerised video-oculography. During space-referenced tasks, the saccade vectors did not fully counter-rotate to compensate for larger angles of body tilt. This finding is in agreement with the 'A' effect reported for the visual vertical. The error was significantly larger for saccades intended to be space-horizontal than space-vertical. This vertico-horizontal dissociation implies greater difficulty in defining horizontality than verticality with the non-visual motor task employed. In contrast, normal Ss (and an alabyrinthine subject tested) were accurate in orienting saccades to their own (cranio-centric) vertical and horizontal axes regardless of tilt indicating that cranio-centric perception is robust and apparently not affected by gravitational influences.