Hybrid 240 Ton Off Highway Haul Truck: Quarterly Technical Status Report 18

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tim Richter

2007-03-31

This eighteenth quarterly status report for the Hybrid Off Highway Vehicle (OHV) project, DOE Award DE-FC04-02AL68080 presents the project status at the end of March 2007, and covers activities in the eighteenth project quarter, January 2007 – March 2007.

Hybrid 240 Ton Off Highway Haul Truck: Quarterly Technical Status Report 19, DOE/AL68080-TSR19

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tim Richter

2007-06-30

This nineteenth quarterly status report for the Hybrid Off Highway Vehicle (OHV) project, DOE Award DE-FC04-02AL68080 presents the project status at the end of June 2007, and covers activities in the nineteenth project quarter, April 2007 – June 2007.

ER Consolidated Qtrly Rpt_July-September 2015_January 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cochran, John R.

2016-01-01

This Environmental Restoration Operations (ER) Consolidated Quarterly Report (ER Quarterly Report) provides the status of ongoing corrective action activities being implemented by Sandia National Laboratories, New Mexico (SNL/NM) for the July, August, and September 2015 quarterly reporting period. The Solid Waste Management Units (SWMUs) and Areas of Concern (AOCs) identified for corrective action at SNL/NM are listed in Table I-1. The work completed during this quarter is reported below in Sections I.2.1 and I.2.2. Section I.2.1 summarizes the quarterly activities at sites undergoing corrective action field activities (SWMUs 8 and 58, 68, 149, 154, and 502, and three groundwater AOCs).more » Section I.2.2 summarizes quarterly activities at sites where the New Mexico Environment Department (NMED) has issued a certificate of completion and the site is in the corrective action complete (CAC) regulatory process. Currently, the Mixed Waste Landfill (MWL, SWMU 76) is the only site in the CAC regulatory process. Corrective action activities have been deferred at the Long Sled Track (SWMU 83), the Gun Facilities (SWMU 84), and the Short Sled Track (SWMU 240) because these are active mission facilities.« less

Automotive Stirling engine development program

NASA Technical Reports Server (NTRS)

Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

1986-01-01

This is the ninth Semiannual Technical Progress Report prepared under the Automotive Stirling Engine Development Program. It covers the twenty-eighth and twenty-ninth quarters of activity after award of the contract. Quarterly Technical Progress Reports related program activities from the first through the thirteenth quarters; thereafter, reporting was changed to a Semiannual format. This report summarizes the study of higher-power kinematic Stirling engines for transportation use, development testing of Mod I Stirling engines, and component development activities. Component development testing included successful conical fuel nozzle testing and functional checkout of Mod II controls and auxiliaries on Mod I engine test beds. Overall program philosophy is outlined and data and test results are presented.

Theoretical study on effects of photodecomposable quenchers in line-and-space pattern fabrication with 7 nm quarter-pitch using chemically amplified electron beam resist process

NASA Astrophysics Data System (ADS)

Kozawa, Takahiro

2017-04-01

The line width roughness (LWR) is a significant issue in the development of chemically amplified resists. The increase in sensitizer concentration is inevitable for the suppression of LWR in the sub-10 nm fabrication. In this study, we investigated the effects of photodecomposable quenchers from the viewpoint of the excluded volume effect, assuming line-and-space patterns with 7 nm quarter-pitch (7 nm space width and 28 nm pitch). The pattern formation of chemically amplified electron beam resists with photodecomposable quenchers was calculated and compared with those with conventional quenchers. It was found that the sum of the concentrations of acid generators and quenchers (photodecomposable or conventional quenchers) can be reduced without decreasing the chemical gradient (an indicator of LWR) by using the photodecomposable quenchers. The photodecomposable quenchers are considered essential in the high-resolution fabrication.

George A. Olah, Carbocation and Hydrocarbon Chemistry

Science.gov Websites

. Final Technical Report. [HF:BF{sub 2}/H{sub 2}] , DOE Technical Report, 1980 Superacid Catalyzed Coal Conversion Chemistry. 1st and 2nd Quarterly Technical Progress Reports, September 1, 1983-March 30, 1984 , DOE Technical Report, 1984 Superacid Catalyzed Coal Conversion Chemistry. Final Technical Report

Quarterly Reporting of Government-Funded Activity to the 2015 National VET Provider Collection. Technical Paper

ERIC Educational Resources Information Center

Foley, Paul

2016-01-01

The topic of more frequent and timely vocational education and training (VET) data has been an issue of interest for a number of years. Since 2015, the National Centre for Vocational Education Research (NCVER) has collected and reported data on government-funded students and courses on a quarterly basis. These quarterly data submissions are…

38 CFR 61.55 - Technical assistance reports.

Code of Federal Regulations, 2011 CFR

2011-07-01

... (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM § 61.55 Technical assistance reports. Each recipient of a technical assistance grant must submit to VA, quarterly, a report describing the activities... 38 Pensions, Bonuses, and Veterans' Relief 2 2011-07-01 2011-07-01 false Technical assistance...

38 CFR 61.55 - Technical assistance reports.

Code of Federal Regulations, 2012 CFR

2012-07-01

... (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM § 61.55 Technical assistance reports. Each recipient of a technical assistance grant must submit to VA, quarterly, a report describing the activities... 38 Pensions, Bonuses, and Veterans' Relief 2 2012-07-01 2012-07-01 false Technical assistance...

38 CFR 61.55 - Technical assistance reports.

Code of Federal Regulations, 2010 CFR

2010-07-01

... (CONTINUED) VA HOMELESS PROVIDERS GRANT AND PER DIEM PROGRAM § 61.55 Technical assistance reports. Each recipient of a technical assistance grant must submit to VA, quarterly, a report describing the activities... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Technical assistance...

Temporal Changes in Technical and Physical Performances During a Small-Sided Game in Elite Youth Soccer Players

PubMed Central

Moreira, Alexandre; Saldanha Aoki, Marcelo; Carling, Chris; Alan Rodrigues Lopes, Rafael; Felipe Schultz de Arruda, Ademir; Lima, Marcelo; Cesar Correa, Umberto; Bradley, Paul S

2016-01-01

Background There have been claims that small-sided games (SSG) may generate an appropriate environment to develop youth players’ technical performance associated to game-related problem solving. However, the temporal change in technical performance parameters of youth players during SSG is still unknown. Objectives The aim of this study was to examine temporal changes in technical and physical performances during a small-sided game (SSG) in elite soccer players. Methods Sixty elite youth players (age 14.8 ± 0.2 yr; stature 177 ± 5 cm; body mass 66.2 ± 4.7 kg) completed a 5 v 5 SSG using two repetitions of 8 minutes interspersed by 3 minutes of passive recovery. To evaluate temporal changes in performance, the data were analysed across 4 minutes quarters. Physical performance parameters included the total distance covered (TDC), the frequency of sprints (>18 km•h-1), accelerations and decelerations (> 2.0 m•s-2 and - 2.0 m•s-2), metabolic power (W•kg-1), training impulse (TRIMP), TDC: TRIMP, number of impacts, and body load. Technical performance parameters included goal attempts, total number of tackles, tackles and interceptions, total number of passes, and passes effectiveness. Results All physical performance parameters decreased from the first to the last quarter with notable declines in TDC, metabolic power and the frequency of sprints, accelerations and decelerations (P < 0.05; moderate to very large ES: 1.08 - 3.30). However, technical performance parameters did not vary across quarters (P > 0.05; trivial ES for 1st v 4th quarters: 0.15 - 0.33). Conclusions The data demonstrate that technical performance is maintained despite substantial declines in physical performance during a SSG in elite youth players. This finding may have implications for designing SSG’s for elite youth players to ensure physical, technical and tactical capabilities are optimized. Modifications in player number, pitch dimensions, rules, coach encouragement, for instance, should be included taking into account the main aim of a given session and then focused on overloading physical or technical elements. PMID:28144411

Temporal Changes in Technical and Physical Performances During a Small-Sided Game in Elite Youth Soccer Players.

PubMed

Moreira, Alexandre; Saldanha Aoki, Marcelo; Carling, Chris; Alan Rodrigues Lopes, Rafael; Felipe Schultz de Arruda, Ademir; Lima, Marcelo; Cesar Correa, Umberto; Bradley, Paul S

2016-12-01

There have been claims that small-sided games (SSG) may generate an appropriate environment to develop youth players' technical performance associated to game-related problem solving. However, the temporal change in technical performance parameters of youth players during SSG is still unknown. The aim of this study was to examine temporal changes in technical and physical performances during a small-sided game (SSG) in elite soccer players. Sixty elite youth players (age 14.8 ± 0.2 yr; stature 177 ± 5 cm; body mass 66.2 ± 4.7 kg) completed a 5 v 5 SSG using two repetitions of 8 minutes interspersed by 3 minutes of passive recovery. To evaluate temporal changes in performance, the data were analysed across 4 minutes quarters. Physical performance parameters included the total distance covered (TDC), the frequency of sprints (>18 km•h -1 ), accelerations and decelerations (> 2.0 m•s -2 and - 2.0 m•s -2 ), metabolic power (W•kg -1 ), training impulse (TRIMP), TDC: TRIMP, number of impacts, and body load. Technical performance parameters included goal attempts, total number of tackles, tackles and interceptions, total number of passes, and passes effectiveness. All physical performance parameters decreased from the first to the last quarter with notable declines in TDC, metabolic power and the frequency of sprints, accelerations and decelerations (P < 0.05; moderate to very large ES: 1.08 - 3.30). However, technical performance parameters did not vary across quarters (P > 0.05; trivial ES for 1st v 4th quarters: 0.15 - 0.33). The data demonstrate that technical performance is maintained despite substantial declines in physical performance during a SSG in elite youth players. This finding may have implications for designing SSG's for elite youth players to ensure physical, technical and tactical capabilities are optimized. Modifications in player number, pitch dimensions, rules, coach encouragement, for instance, should be included taking into account the main aim of a given session and then focused on overloading physical or technical elements.

SATNET development and operation. Pluribus satellite IMP development. Remote site maintenance. Internet operations and maintenance. Mobile access terminal network. TCP for the HP3000. TCP-TAC. TCP for VAX-UNIX. Combined quarterly technical report

NASA Astrophysics Data System (ADS)

Bressler, R. D.

1981-11-01

This quarterly technical report describes work on the development of and experimentation with packet broadcast by satellite; on development of Pluribus Satellite IMPs; on a study of the technology of Remote Site Maintenance; on Internetwork monitoring; on shipboard satellite communications; and on the development of Transmission Control Protocols for the HP3000, TAC, and VAX-UNIX.

Enhanced oil recovery utilizing high-angle wells in the Frontier Formation, Badger Basin Field, Park County, Wyoming. Quarterly technical progress report, 1 March 1993--30 June 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fortmann, R.G.; Walker, J.P.

1993-07-10

Sierra Energy Company`s targeted goals during the third quarter of this Cooperative Agreement included the following objectives from the Statement of Work: in Phase 2A, completion of subtask 2.1.2--acquire best possible field data in the 3-D seismic program; and initiation of Subtask 2.1.3--process acquired 3-D seismic data. Technical progress is described for these tasks.

38 CFR 61.55 - Technical assistance reports.

Code of Federal Regulations, 2014 CFR

2014-07-01

... assistance reports. Each technical assistance grantee must submit to VA a quarterly report describing the... 38 Pensions, Bonuses, and Veterans' Relief 2 2014-07-01 2014-07-01 false Technical assistance reports. 61.55 Section 61.55 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS...

38 CFR 61.55 - Technical assistance reports.

Code of Federal Regulations, 2013 CFR

2013-07-01

... assistance reports. Each technical assistance grantee must submit to VA a quarterly report describing the... 38 Pensions, Bonuses, and Veterans' Relief 2 2013-07-01 2013-07-01 false Technical assistance reports. 61.55 Section 61.55 Pensions, Bonuses, and Veterans' Relief DEPARTMENT OF VETERANS AFFAIRS...

47 CFR 79.3 - Video description of video programming.

Code of Federal Regulations, 2011 CFR

2011-10-01

... description per calendar quarter, either during prime time or on children's programming; (2) Television... technical capability necessary to pass through the video description, unless using the technology for... video description per calendar quarter during prime time or on children's programming, on each channel...

47 CFR 79.3 - Video description of video programming.

Code of Federal Regulations, 2010 CFR

2010-10-01

... description per calendar quarter, either during prime time or on children's programming; (2) Television... technical capability necessary to pass through the video description, unless using the technology for... video description per calendar quarter during prime time or on children's programming, on each channel...

The magnetohydrodynamics coal-fired flow facility

NASA Astrophysics Data System (ADS)

1995-01-01

In this quarterly technical progress report, UTSI reports on the status of a multitask contract to develop the technology for the steam bottoming portion of a MHD Steam Combined Cycle Power Plant. The report describes the facility maintenance and environmental work completed, status of completing technical reports and certain key administrative actions occurring during the quarter. With program resources at a minimum to closeout the MHD program, no further testing occurred during the quarter, but the DOE CFFF facility was maintained in a standby status with winterization, preventive maintenance and repairs accomplished as needed. Plans and preparations progressed for environmental actions needed at the site to investigate and characterize the groundwater and for removal/disposal of asbestos in the cooling tower. Work continued to progress on archiving the results of the MHD program.

Solar thermal components. A bibliography with abstracts

NASA Technical Reports Server (NTRS)

Bozman, W. R. (Editor)

1979-01-01

This bibliographic series cites and abstracts literature and technical papers on components applied to solar thermal energy utilization. The quarterly volumes are divided into ten categories: material properties; flat plat collectors; concentrating collectors; thermal storage; heat pumps; coolers and heat exchangers; solar ponds and distillation; greenhouses; process pleat; and irrigation pumps. Each quarterly volume is compiled from a wide variety of data bases, report literature, technical briefs, journal articles and other traditional and non traditional sources. The Technology Application Center maintains a library containing many of the articles and publications referenced in the series.

Combined Quarterly Technical Report Number 16. SATNET Development and Operation, Pluribus Satellite IMP Development, Remote Site Maintenance, Internet Development, Mobile Access Terminal Network.

DTIC Science & Technology

1980-02-01

Reserch Projects Agency I t&* ISO~p~A d m* ab~b ~I 41 b~bmso 544,A UNCLASSIFIED S@MYT SLAMIICAIGH OF TNNI PAOE tpvm Gamb.______________ RI...Wi do m,.we a#& N m WUNP SMei r -- This Quarterly Technical Report describes work on the development of and experimentation with packet broadcast by...interval by either segmenting or aggregating the stream packets such that they match the system interval. Since this approach is simple with respect

77 FR 4862 - Agency Requests for Renewal of a Previously Approved Information Collection: SBTRC Regional Field...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-31

..., marketing, meetings/ conferences, and services to businesses as completed during the quarter. The Quarterly... include business analysis, general management & technical assistance and training, business counseling...) AGENCY: Office of Small and Disadvantaged Business Utilization (OSDBU), Office of the Secretary of...

My Career and the "Rhetoric of" Technical Writing and Communication

ERIC Educational Resources Information Center

Schuster, Mary Lay

2015-01-01

This article traces the history of Mary Schuster's career in technical writing and communication from 1968 when she took a position in the Publications Department at the Institute of Electrical and Electronics Engineers (IEEE) to her work at "Technical Communication Quarterly" ("TCQ") in 2003 and forward. She discusses the…

RTO Technical Report: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2002-01-01

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information from April 1,2002 through June 30, 2002. Topics covered include: intrusion detection and design loads for aircraft.

Detoxification and generation of useful products from coal combustion wastes: Quarterly technical report, (October--December 1988)

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1988-01-01

This quarter, samples of dry fly ash, wet bottom ash, and desulfurization gypsum slurry were provided from an Ohio Edison power plant. Chemical analysis mineralogical examination, and an anion analysis were performed on the samples. 2 figs., 1 tab. (CBS)

Remote sensing of natural resources: Quarterly literature review

NASA Technical Reports Server (NTRS)

1976-01-01

A quarterly review of technical literature concerning remote sensing techniques is presented. The format contains indexed and abstracted materials with emphasis on data gathering techniques performed or obtained remotely from space, aircraft, or ground-based stations. Remote sensor applications including the remote sensing of natural resources are presented.

7 CFR Exhibit B to Subpart I of... - Evaluation Report of Self-Help Technical Assistance (TA) Grants

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 13 2014-01-01 2013-01-01 true Evaluation Report of Self-Help Technical Assistance... Self-Help Technical Assistance Grants Pt. 1944, Subpt. I, Exh. B Exhibit B to Subpart I of Part 1944—Evaluation Report of Self-Help Technical Assistance (TA) Grants Evaluation for Quarter Ending:(1...

7 CFR Exhibit B to Subpart I of... - Evaluation Report of Self-Help Technical Assistance (TA) Grants

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 13 2012-01-01 2012-01-01 false Evaluation Report of Self-Help Technical Assistance... Self-Help Technical Assistance Grants Pt. 1944, Subpt. I, Exh. B Exhibit B to Subpart I of Part 1944—Evaluation Report of Self-Help Technical Assistance (TA) Grants Evaluation for Quarter Ending:(1...

7 CFR Exhibit B to Subpart I of... - Evaluation Report of Self-Help Technical Assistance (TA) Grants

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 13 2013-01-01 2013-01-01 false Evaluation Report of Self-Help Technical Assistance... Self-Help Technical Assistance Grants Pt. 1944, Subpt. I, Exh. B Exhibit B to Subpart I of Part 1944—Evaluation Report of Self-Help Technical Assistance (TA) Grants Evaluation for Quarter Ending:(1...

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2001-01-01

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information from Oct 1, 2001 through Dec 31, 2001. This listing includes one citataion titled 'Logistics Test and Evaluation in Flight'.

West Hackberry Tertiary Project. Quarterly technical progress report, July 1--September 30, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The goal of the West Hackberry Tertiary Project is to demonstrate the technical and economic feasibility of combining air injection with the Double Displacement Process for tertiary oil recovery. The Double Displacement Process is the gas displacement of a water invaded oil column for the purpose of recovering oil through gravity drainage. The novel aspect of this project is the use of air as the injection fluid. The target reservoir for the project is the Camerina C-1,2,3 Sand located on the West Flank of West Hackberry Field in Cameron Parish, Louisiana. If successful, this project will demonstrate that the usemore » of air injection in the Double Displacement Process can economically recover oil in reservoirs where tertiary oil recovery is presented uneconomic. During this quarter, the West Hackberry Tertiary Project completed the first ten months of air injection operations. Plots of air injection rates and cumulative air injected are included in this report as attachments. The following events are reviewed in this quarter`s technical progress report: (1) successful workovers on the Gulf Land D Nos. 44, 45 and 51 and the Watkins No. 3; (2) the unsuccessful repair attempt on the Watkins No. 16; (3) gathering of additional bottom hole pressure data; (4) air compressor operations and repairs; and (5) technology transfer activities.« less

76 FR 44958 - Solicitation for a Cooperative Agreement-Quarterly Publication of a “Corrections Mental Health...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-07-27

... Agreements,'' which will be included in the award package); (2) Adhere to best practices in technical writing... there evidence of experience in corrections, mental health, or technical writing that would demonstrate... at http://www.nicic.gov . All technical or programmatic questions concerning this announcement should...

Assigning a Thesis Project In the Two-Year Architectural Technology Program

ERIC Educational Resources Information Center

Obermeyer, Thomas

1977-01-01

The "thesis project" assigned in the sixth quarter of the eight-quarter architectural technology program at the Dakota County Area Vocational-Technical Institute in Rosemont, Minnesota, requires the students to design a building for a local public service organization or government agency. The complete project will include a program, a…

Pittsburgh Technical Health Training Institute Demonstration Project; Quarterly Report.

ERIC Educational Resources Information Center

Kishkunas, Louis J.

This fifth quarterly report covers the period June 15, 1967 to December 15, 1967 of a project aimed at demonstrating a faster method of training higly qualified workers for the health field. During this period, nurse aides were trained in a pilot program based upon the educational objectives derived from entry level behavioral specifications…

PFBC HGCU Test Facility. Technical progress report No. 24, Third quarter, CY 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This is the twenty-fourth and final Technical Progress Report submitted to the Department of Energy (DOE) in connection with the cooperative agreement between the DOE and Ohio Power Company for the Tidd PFBC Hot Gas Clean Up Test Facility. This report covers the work completed during the Third Quarter of CY 1995. All activity this quarter was directed toward the completion of the program final report. A draft copy of the final report was forwarded to DOE during this quarter, and DOE submitted their comments on the report to AEPSC. DOE requested that Westinghouse write an appendix to the reportmore » covering the performance of the fail-safe regenerator devices during Tad operation, and Westinghouse subsequently prepared the appendix. Additional DOE comments were incorporated into the report, and it will be issued in camera-ready form by the end of October, 1995, which is the program end date. Appendix 1 presents the results of filter candle posttest examination by Westinghouse performed on selected filter candles following final shutdown of the system.« less

Geothermal direct-heat utilization assistance. Quarterly report, January - March 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lienau, P.

1997-04-01

This report summarizes geothermal technical assistance, R&D and technology transfer activities of the Geo-Heat Center at Oregon Institute of Technology for the second quarter of FY-97. It describes 176 contacts with parties during this period related to technical assistance with geothermal direct heat projects. Areas dealt with include geothermal heat pumps, space heating, greenhouses, aquaculture, equipment, economics and resources. Research activities are summarized on well pumping in commercial groundwater heat pump systems. A memorandum of understanding between the GHC and EIA is described. Work accomplishments on the Guidebook are discussed. Outreach activities include the publication of a geothermal direct usemore » Bulletin, dissemination of information, geothermal library, technical papers and seminars, and progress monitor reports on geothermal resources and utilization.« less

Lawrence Livermore National Laboratory Safeguards and Security quarterly progress report to the US Department of Energy: Quarter ending December 31, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, G.; Mansur, D.L.; Ruhter, W.D.

1994-01-01

The Lawrence Livermore National Laboratory (LLNL) carries out safeguards and security activities for the Department of Energy (DOE), Office of Safeguards and Security (OSS), as well as other organizations, both within and outside the DOE. This document summarizes the activities conducted for the OSS during the first quarter of fiscal year 1994 (October through December, 1993). The nature and scope of the activities carried out for OSS at LLNL require a broad base of technical expertise. To assure projects are staffed and executed effectively, projects are conducted by the organization at LLNL best able to supply the needed technical expertise.more » These projects are developed and managed by senior program managers. Institutional oversight and coordination is provided through the LLNL Deputy Director`s office. At present, the Laboratory is supporting OSS in five areas: (1) Safeguards Technology, (2) Safeguards and Decision Support, (3) Computer Security, (4) DOE Automated Physical Security, and (5) DOE Automated Visitor Access Control System. This report describes the activities in each of these five areas. The information provided includes an introduction which briefly describes the activity, summary of major accomplishments, task descriptions with quarterly progress, summaries of milestones and deliverables and publications published this quarter.« less

Lawrence Livermore National Laboratory safeguards and security quarterly progress report to the U.S. Department of Energy. Quarter ending December 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davis, G.; Mansur, D.L.; Ruhter, W.D.

The Lawrence Livermore National Laboratory (LLNL) carries out safeguards and security activities for the Department of Energy (DOE), Office of Safeguards and Security (OSS), as well as other organizations, both within and outside the DOE. This document summarizes the activities conducted for the OSS during the First Quarter of Fiscal Year 1997 (October through December, 1996). The nature and scope of the activities carried out for OSS at LLNL require a broad base of technical expertise. To assure projects are staffed and executed effectively, projects are conducted by the organization at LLNL best able to supply the needed technical expertise.more » These projects are developed and managed by senior program managers. Institutional oversight and coordination is provided through the LLNL Deputy Director`s office. At present, the Laboratory is supporting OSS in four areas: (1) safeguards technology; (2) safeguards and material accountability; (3) computer security--distributed systems; and (4) physical and personnel security support. The remainder of this report describes the activities in each of these four areas. The information provided includes an introduction which briefly describes the activity, summary of major accomplishments, task descriptions with quarterly progress, summaries of milestones and deliverables and publications published this quarter.« less

Washington State Board for Community and Technical Colleges Enrollment and Staffing Report, Fall 2014

ERIC Educational Resources Information Center

Washington State Board for Community and Technical Colleges, 2014

2014-01-01

The "Fall Enrollment and Staffing Report 2014" provides a snapshot of enrollments in community and technical colleges during fall quarter 2014. The report addresses the questions most commonly raised regarding the community and technical colleges in Washington. The primary source of information for this document is the State Board for…

Washington State Board for Community and Technical Colleges Enrollment and Staffing Report, Fall 2013

ERIC Educational Resources Information Center

Washington State Board for Community and Technical Colleges, 2013

2013-01-01

The "Fall Enrollment and Staffing Report 2013" provides a snapshot of enrollments in community and technical colleges during fall quarter 2013. The report addresses the questions most commonly raised regarding the community and technical colleges in Washington. The primary source of information for this document is the State Board for…

Treatment of Race/Ethnicity in Career-Technical Education Research

ERIC Educational Resources Information Center

Rojewski, Jay W.; Xing, Xue

2013-01-01

This study examined how researchers of career-technical education have treated the construct of race/ethnicity in recent studies. Fifty-one of 71 articles published in the Career and Technical Education Research (CTER) over a 7-year span (2005-2011) were included. A content analysis found that only one quarter (n = 13, 25.49%) of eligible studies…

Government Information Quarterly. Volume 7, no. 2: National Aeronautics and Space Administration Scientific and Technical Information Programs. Special issue

NASA Technical Reports Server (NTRS)

Hernon, Peter (Editor); Mcclure, Charles R. (Editor); Pinelli, Thomas E. (Editor)

1990-01-01

NASA scientific and technical information (STI) programs are discussed. Topics include management of information in a research and development agency, the new space and Earth science information systems at NASA's archive, scientific and technical information management, and technology transfer of NASA aerospace technology to other industries.

ANNUAL REPORT, JULY 1, 1957

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1958-10-31

The progress and trends of research are presented along with a description of operational, service, end administrative activities. Some scientific and technical details are given on research programs in the physical sciences, life sciences, and engineering, however, more complete technical information is available in quarterly progress reports, BNL technical reports, and scientific and technical periodicals. A bibliography of these publications is appended. (For preceding period see BNL-426.) (D.E.B.)

78 FR 17394 - Filing via the Internet; Electronic Tariff Filings; Revisions to Electric Quarterly Report Filing...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-21

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket Nos. RM07-16-000; RM01-5-000; RM12-3-000] Filing via the Internet; Electronic Tariff Filings; Revisions to Electric Quarterly Report Filing Process; Notice of Technical Conference Take notice that on April 16, 2013, the staff of the...

Jet Crackle

DTIC Science & Technology

2015-06-23

DISTRIBUTION/AVAILABILITY STATEMENT DISTRIBUTION A 13. SUPPLEMENTARY NOTES 14. ABSTRACT Fighter jets and other aircraft with high specific thrust engines...interim, memorandum, master’s thesis , progress, quarterly, research, special, group study, etc. 3. DATES COVERED. Indicate the time during which the...State the type of report, such as final, technical, interim, memorandum, master’s thesis , progress, quarterly, research, special, group study, etc

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2002-01-01

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information from Jan 1, 2002 through Mar 31, 2002. Topics covered included information management, ice accretion, digital flight control systems, supercavitation flows, and tactical decision aids.

Temporally-stable active precision mount for large optics.

PubMed

Reinlein, Claudia; Damm, Christoph; Lange, Nicolas; Kamm, Andreas; Mohaupt, Matthias; Brady, Aoife; Goy, Matthias; Leonhard, Nina; Eberhardt, Ramona; Zeitner, Uwe; Tünnermann, Andreas

2016-06-13

We present a temporally-stable active mount to compensate for manufacturing-induced deformations of reflective optical components. In this paper, we introduce the design of the active mount, and its evaluation results for two sample mirrors: a quarter mirror of 115 × 105 × 9 mm³, and a full mirror of 228 × 210 × 9 mm³. The quarter mirror with 20 actuators shows a best wavefront error rms of 10 nm. Its installation position depending deformations are addressed by long-time measurements over 14 weeks indicating no significance of the orientation. Size-induced differences of the mount are studied by a full mirror with 80 manual actuators arranged in the same actuator pattern as the quarter mirror. This sample shows a wavefront error rms of (27±2) nm over a measurement period of 46 days. We conclude that the developed mount is suitable to compensate for manufacturing-induced deformations of large reflective optics, and likely to be included in the overall systems alignment procedure.

Q4 2016/Q1 2017 Solar Industry Update

DOE Office of Scientific and Technical Information (OSTI.GOV)

Margolis, Robert; Feldman, David; Boff, Daniel

2017-05-17

This technical presentation provides an update on the major trends that occurred in the solar industry in the fourth quarter of 2016 and the first quarter of 2017. Major topics of focus include global and U.S. supply and demand, module and system price, investment trends and business models, and updates on U.S. government programs supporting the solar industry.

AgRISTARS documents tracking list report

NASA Technical Reports Server (NTRS)

Hawkins, J. L.

1983-01-01

A quarterly listing of documents issued and placed in the AgRISTARS tracking system is provided. The technical publications are arranged by type of documents. The reference AgRISTARS document number, title and date of publication, the issuing organization, and the National Technical Information Service reference number is given.

Strategic petroleum reserve supporting research. Quarterly technical report, January 1-March 31, 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Woodward, P.W.

1986-01-01

The basic objective is to provide technical support to the Strategic Petroleum Reserve Office (SPRO), through the Bartlesville Project Office. This support includes routine analyses, experimental research, and technical consultation at the SPRO's request. Accomplishments for this past quarter include: stable D, /sup 34/S, and /sup 13/C isotope ratio analyses for 27 samples of SPR crude oil; gas chromatographic simulated distillation (Sim-dis) of 74 SPR crude samples; sim-dis of sludge samples to check for bimodal distributions; data for 8 comprehensive analyses have been entered into the Bonner and Moore ''Crude Assay II'' library; 25 samples which included both whole crudesmore » and distillate fractions were chromatographed using Siemens dual-oven GC and PIANO software; separation of 4 sludge samples into acid, base, and neutral fractions by ion exchange chromatography; and proton and sodium-23 NMR measurements of sludge samples. 1 fig., 5 tabs.« less

Economic feasibility of producing inside-out beams from small-diameter logs

Treesearch

David W. Patterson; Richard A. Kluender; James E. Granskog

2002-01-01

Previous work has shown that it is technically feasible to produce inside-out (ISO) beams by taking small-diameter (5 to 7 in.) logs, slabbing four sides, quartering the cant, and turning the quarters inside out and gluing them together. After drying, the beams were found to be straight, with no cracks, and of equal or better mechanical properties than solid sawn...

Amarillo National Resource Center for Plutonium quarterly technical progress report, August 1, 1997--October 31, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This report summarizes activities of the Amarillo National Resource Center for Plutonium during the quarter. The report describes the Electronic Resource Library; DOE support activities; current and future environmental health and safety programs; pollution prevention and pollution avoidance; communication, education, training, and community involvement programs; and nuclear and other material studies, including plutonium storage and disposition studies.

Acquisition Review quarterly. Vol. 1, No. 3, Summer 1994

DTIC Science & Technology

1994-01-01

implications , and suggests the use of explicit demand curves. 281 - GUIDELINES FOR AUTHORS Acquisition Review Quarterly Summer 1994 - ii The Lemon Juice...environment. This attention is long overdue. Defense Department installations cover tens of millions oQf square miles of the American landscape. If you look...Commission Report, Facing Towards Governments - Nongovernmental Organi- zations and Scientific and Technical Advice (New York: Carnegie Commission, January

Decontamination Systems Information and Research Program. Quarterly technical progress report, January 1--March 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-05-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Reports on a quarterly basis. This report comprises the first Quarterly Technical Progress Report for Year 2 of the Agreement. This report reflects the progress and/or efforts performed on the sixteen (16) technical projects encompassed by the Year 2 Agreement for the period of January 1 through March 31, 1994. In situ bioremediation ofmore » chlorinated organic solvents; Microbial enrichment for enhancing in-situ biodegradation of hazardous organic wastes; Treatment of volatile organic compounds (VOCs) using biofilters; Drain-enhanced soil flushing (DESF) for organic contaminants removal; Chemical destruction of chlorinated organic compounds; Remediation of hazardous sites with steam reforming; Soil decontamination with a packed flotation column; Use of granular activated carbon columns for the simultaneous removal of organics, heavy metals, and radionuclides; Monolayer and multilayer self-assembled polyion films for gas-phase chemical sensors; Compact mercuric iodide detector technology development; Evaluation of IR and mass spectrometric techniques for on-site monitoring of volatile organic compounds; A systematic database of the state of hazardous waste clean-up technologies; Dust control methods for insitu nuclear and hazardous waste handling; Winfield Lock and Dam remediation; and Socio-economic assessment of alternative environmental restoration technologies.« less

Plasmonic Structure Integrated Single-Photon Detector Configurations to Improve Absorptance and Polarization Contrast

PubMed Central

Csete, Mária; Szekeres, Gábor; Szenes, András; Szalai, Anikó; Szabó, Gábor

2015-01-01

Configurations capable of maximizing both the absorption component of system detection efficiency and the achievable polarization contrast were determined for 1550 nm polarized light illumination of different plasmonic structure integrated superconducting nanowire single-photon detectors (SNSPDs) consisting of p = 264 nm and P = 792 nm periodic niobium nitride (NbN) patterns on silica substrate. Global effective NbN absorptance maxima appear in case of p/s-polarized light illumination in S/P-orientation (γ = 90°/0° azimuthal angle) and the highest polarization contrast is attained in S-orientation of all devices. Common nanophotonical origin of absorptance enhancement is collective resonance on nanocavity gratings with different profiles, which is promoted by coupling between localized modes in quarter-wavelength metal-insulator-metal nanocavities and laterally synchronized Brewster-Zenneck-type surface waves in integrated SNSPDs possessing a three-quarter-wavelength-scaled periodicity. The spectral sensitivity and dispersion characteristics reveal that device design specific optimal configurations exist. PMID:25654724

Results for the Fourth Quarter Calendar Year 2015 Tank 50H Salt Solution Sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.

In this memorandum, the chemical and radionuclide contaminant results from the Fourth Quarter Calendar Year 2015 (CY15) sample of Tank 50H salt solution are presented in tabulated form. The Fourth Quarter CY15 Tank 50H samples were obtained on October 29, 2015 and received at Savannah River National Laboratory (SRNL) on October 30, 2015. The information from this characterization will be used by Defense Waste Processing Facility (DWPF) & Saltstone Facility Engineering for the transfer of aqueous waste from Tank 50H to the Salt Feed Tank in the Saltstone Production Facility, where the waste will be treated and disposed of inmore » the Saltstone Disposal Facility. This memorandum compares results, where applicable, to Saltstone Waste Acceptance Criteria (WAC) limits and targets. Data pertaining to the regulatory limits for Resource Conservation and Recovery Act (RCRA) metals will be documented at a later time per the Task Technical and Quality Assurance Plan (TTQAP) for the Tank 50H saltstone task. The chemical and radionuclide contaminant results from the characterization of the Fourth Quarter Calendar Year 2015 (CY15) sampling of Tank 50H were requested by SRR personnel and details of the testing are presented in the SRNL Task Technical and Quality Assurance Plan.« less

NCEL (Naval Civil Engineering Laboratory) Quarterly Abstracts of Technical Documents, 1 April to 30 June 1987.

DTIC Science & Technology

1987-06-30

release; distribution unlimited. 87 8 3075 TABLE OF CONTENTS page TECHNICAL NOTES N-1764 Validation of Nitronic 33 in Reinforced and Prestressed...TECHNICAL WES K- 1764 Validation of Nitrovic 33 In Reeinforced and Prestressed Concrete, Apr 1987, James F. Jenkins (public release) Nitronic 33...prestressing strand are not acceptable. Before Nitronic 33 stainless steel prestressed concrete waterfront structures were constructed, it was necessary to

The Design and Transfer of Advanced Command and Control (C2) Computer-Based Systems

DTIC Science & Technology

1980-03-31

TECHNICAL REPORT 80-02 QUARTERLY TECHNICAL REPORT: THE DESIGN AND TRANSFER OF ADVANCED COMMAND AND CONTROL (C 2 ) COMPUTER-BASED SYSTEMS ARPA...The Tasks/Objectives and/or Purposes of the overall project are connected with the design , development, demonstration and transfer of advanced...command and control (C2 ) computer-based systems; this report covers work in the computer-based design and transfer areas only. The Technical Problems thus

Computational modeling and experimental studies on NO{sub x} reduction under pulverized coal combustion conditions. Seventh quarterly technical progress report, July 1, 1996--September 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumpaty, S.K.; Subramanian, K.; Nokku, V.P.

1996-12-31

During this quarter (July-August 1996), the experiments for nitric oxide reburning with a combination of methane and ammonia were conducted successfully. This marked the completion of gaseous phase experiments. Preparations are underway for the reburning studies with coal. A coal feeder was designed to suit our reactor facility which is being built by MK Fabrication. The coal feeder should be operational in the coming quarter. Presented here are the experimental results of NO reburning with methane/ammonia. The results are consistent with the computational work submitted in previous reports.

7 CFR Exhibit B-1 to Subpart I of... - Instructions for Preparation of Evaluation Report of Self-Help Technical Assistance Grants

Code of Federal Regulations, 2011 CFR

2011-01-01

.... Insert the number of equivalent units (EU) completed the first/second/third month of the quarter using steps 1, 2, and 3 of exhibit B-3. 8. Insert the number of EU's completed the second month of the quarter by using steps 1, 2, and 3 of exhibit B-3. 9. Insert the number of EU's completed the third month of...

7 CFR Exhibit B-1 to Subpart I of... - Instructions for Preparation of Evaluation Report of Self-Help Technical Assistance Grants

Code of Federal Regulations, 2010 CFR

2010-01-01

.... Insert the number of equivalent units (EU) completed the first/second/third month of the quarter using steps 1, 2, and 3 of exhibit B-3. 8. Insert the number of EU's completed the second month of the quarter by using steps 1, 2, and 3 of exhibit B-3. 9. Insert the number of EU's completed the third month of...

A Second Follow-Up Year for "Measuring How Benchmark Assessments Affect Student Achievement." REL Technical Brief. REL 2008-No. 002

ERIC Educational Resources Information Center

Henderson, Susan; Petrosino, Anthony; Guckenburg, Sarah; Hamilton, Stephen

2008-01-01

This technical brief examines whether, after two years of implementation, schools in Massachusetts using quarterly benchmark exams aligned with state standards in middle school mathematics showed greater gains in student achievement than those not doing so. A quasi-experimental design, using covariate matching and comparative interrupted…

Geothermal direct-heat utilization assistance. Federal Assistance Program quarterly project progress report, April 1--June 30, 1998

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-07-01

This report summarizes geothermal technical assistance, R and D and technology transfer activities of the Geo-Heat Center at Oregon Institute of Technology for the third quarter of FY98 (April--June, 1998). It describes 231 contacts with parties during this period related to technical assistance with geothermal direct heat projects. Areas dealt with included requests for general information including material for high school and university students, and material on geothermal heat pumps, resource and well data, spacing heating and cooling, greenhouses, aquaculture, equipment, district heating, resorts and spas, industrial applications, snow melting and electric power. Research activities include work on model constructionmore » specifications for line shaft submersible pumps and plate heat exchangers, and a comprehensive aquaculture developers package. A brochure on Geothermal Energy in Klamath County was developed for state and local tourism use. Outreach activities include the publication of the Quarterly Bulletin (Vol. 19, No. 2) with articles on research at the Geo-Heat Center, sustainability of geothermal resources, injection well drilling in Boise, ID and a greenhouse project in the Azores. Other outreach activities include dissemination of information mainly through mailings of publications, tours of local geothermal uses, geothermal library acquisitions and use, participation in workshops, short courses and technical meetings by the staff, and progress monitor reports on geothermal activities.« less

Development of critical dimension measurement scanning electron microscope for ULSI (S-8000 series)

NASA Astrophysics Data System (ADS)

Ezumi, Makoto; Otaka, Tadashi; Mori, Hiroyoshi; Todokoro, Hideo; Ose, Yoichi

1996-05-01

The semiconductor industry is moving from half-micron to quarter-micron design rules. To support this evolution, Hitachi has developed a new critical dimension measurement scanning electron microscope (CD-SEM), the model S-8800 series, for quality control of quarter- micron process lines. The new CD-SEM provides detailed examination of process conditions with 5 nm resolution and 5 nm repeatability (3 sigma) at accelerating voltage 800 V using secondary electron imaging. In addition, a newly developed load-lock system has a capability of achieving a high sample throughput of 20 wafers/hour (5 point measurements per wafer) under continuous operation. To support user friendliness, the system incorporates a graphical user interface (GUI), an automated pattern recognition system which helps locating measurement points, both manual and semi-automated operation, and user-programmable operating parameters.

GEO satellite markets and functions : Quarterly Launch Report : special report

DOT National Transportation Integrated Search

1996-01-01

The information revolution has transformed telecommunication markets. The explosive demand for global communication has spawned accelerating technical innovation and fierce competition for telecommunication revenues. Deregulation of telecommunication...

Educational Technology Program. Quarterly Technical Summary, Period Ending 31 May 1970.

ERIC Educational Resources Information Center

Frick, Frederick C.

An overview of the Lincoln Training System (LTS) and descriptions of the hardward and software of the LTS-1 and LTS-2 systems are provided. The overall program seeks to develop, test, and evaluate technical aids to vocational training systems. These are appropriate to this field because the high costs need to be reduced and because there are clear…

AgRISTARS documents tracking list report

NASA Technical Reports Server (NTRS)

Hawkins, J. L.

1982-01-01

A quarterly listing of those documents and related publications that have been issued and placed in the AgRISTARS tracking system is presented. The Tracking List Report provides a catalog, by project, of technical publications arranged by type of document and gives the reference AgRISTARS document numbers, title and date of publication, the issuing organization, and the National Technical Information Service reference number.

Design and prototyping of HL-LHC double quarter wave crab cavities for SPS test

DOE Office of Scientific and Technical Information (OSTI.GOV)

Verdu-Andres, S.; Skaritka, J.; Wu, Q.

2015-05-03

The LHC high luminosity project envisages the use of the crabbing technique for increasing and levelling the LHC luminosity. Double Quarter Wave (DQW) resonators are compact cavities especially designed to meet the technical and performance requirements for LHC beam crabbing. Two DQW crab cavities are under fabrication and will be tested with beam in the Super Proton Synchrotron (SPS) at CERN by 2017. This paper describes the design and prototyping of the DQW crab cavities for the SPS test.

Analysis of scanner data for crop inventories

NASA Technical Reports Server (NTRS)

Horvath, R. (Principal Investigator); Cicone, R. C.; Kauth, R. J.; Malila, W. A.; Pont, W.; Thelen, B.; Sellman, A.

1981-01-01

Accomplishments for a machine-oriented small grains labeler T&E, and for Argentina ground data collection are reported. Features of the small grains labeler include temporal-spectral profiles, which characterize continuous patterns of crop spectral development, and crop calendar shift estimation, which adjusts for planting date differences of fields within a crop type. Corn and soybean classification technology development for area estimation for foreign commodity production forecasting is reported. Presentations supporting quarterly project management reviews and a quarterly technical interchange meeting are also included.

Proof of the Feasibility of Coherent and Incoherent Schemes for Pumping a Gamma-Ray Laser

DTIC Science & Technology

1988-07-01

DIP!; ilLE-CWPj AD-A 799 638 The University of Texas at DallasCenter for Quantlin, Electronics The Gamma-Ray Laser Project Quarterly Report April...AND INCOHERENT SCHEMES FOR PUMPING A GAMMA-RAY LASER Principal Investigator: Carl B. Collins The University of Texas at Dallas Center for Quantum...FEASIBILITY OF Quarterly Technical Progress COHERENT AND INCOHERENT SCHEMES /I/RR - 61WARA FOR PUMPING A GAMMA-RAY LASER 6.PERFORMINO ORG. REPORT NUMBER

Computational Modeling and Experimental Studies on NO(x) Reduction Under Pulveerized Coal Combustion Conditions. Quarterly technical progress report, July 1 - September 30, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumpaty, S.K.; Subramanian, K.; Darboe, A.

1997-12-31

Several experiments were conducted during this quarter to study the NO{sub x} reduction effectiveness of lignite coal, activated carbon and catalytic sites such as calcium sulfide and calcium carbide. While some of the coals/chemicals could be fed easily, some needed the mixing with silica gel to result in a uniform flow through the feeder. Several trial runs were performed to ensure proper feeding of the material before conducting the actual experiment to record NO{sub x} reduction. The experimental approach has been the same as presented in the past two quarterly reports with the coal reburning experiments. Partial reduction is achievedmore » through methane addition for SR2=0.95 conditions and then coal or the catalyst is introduced to see if there is further reduction. Presented below are the results of the experiments conducted during this quarter.« less

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Simmons, Kevin L.

This quarterly report summarizes the status for the project planning to complete all the legal and contract documents required for establishing the subcontracts needed and a Cooperative Research and Development Agreement (CRADA) with Autodesk, Inc., Toyota Motor Engineering and Manufacturing North America (Toyota), and Magna Exterior and Interiors Corporation (Magna). During the second quarter (1/1/2013 to 3/31/2013), all the technical and legal documents for the subcontracts to Purdue University, University of Illinois, and PlastiComp, Inc. were completed. The revised CRADA documents were sent to DOE, Autodesk, Toyota, and Magna for technical and legal reviews. PNNL Legal Services contacted project partners’more » Legal counterparts for completing legal documents for the project. A non-disclosure agreement was revised and sent to all the parties for reviews.« less

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2004-01-01

This is a listing of recent unclassified RTO technical publications for April 1, 2004 through June 30, 2004, processed by the NASA Center for AeroSpace Information. Topics covered include: heat transfer and cooling in propulsion and power systems; assessment of operator functional state; microwaves; aerodynamics in solid rocket propulsion; command, control, communications and intelligence modeling; personal protective equipment against anti-personnel mine blast; and data fusion and visualization.

QUARTERLY TECHNICAL PROGRESS REPORT, JULY, AUGUST, SEPTEMBER 1967.

DTIC Science & Technology

Contents: Circuit research program; Hardware systems research; Computer system software research; Illinois pattern recognition computer: ILLIAC II... service , use, and program development; IBM 7094/1401 service , use, and program development; Problem specifications; General laboratory information.

SeaQuaKE: Sea-optimized Quantum Key Exchange

DTIC Science & Technology

2014-11-01

ONRBAA13-001). In this technical report, we describe modeling results of an entangled photon - pair source based on spontaneous four-wave mixing for...Distribution Special Notice (13-SN- 0004 under ONRBAA13-001). In this technical report, we describe modeling results of an entangled photon - pair ...areas over the last quarter include (i) development of a wavelength-dependent, entangled photon - pair source model and (ii) end-to-end system modeling

Life as a NATO Engineer

DTIC Science & Technology

2010-08-01

NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND...management; leads military in case of specialized survey; supervises more than 25 local civilian employees ; acts as technical expert during contract...Security Assistance Force Head- quarters Camp. I knew I could handle the job of project manager, but wondered about acting as contract manager, technical ex

Administrative Information Systems Plan for FY89

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1988-11-01

The Administrative Information Systems (AIS) Plan was developed to prioritize, track, and control the cost of AIS activities. This annually published plan, in conjunction with quarterly status reports, measures projected AIS activities and progress. The AIS Plan and quarterly reporting are administered jointly by the Director of Computing and an Organization 30 director. Priority development projects are clearly defined and closely managed efforts that consume significant resources. Directorate supplementals describe other AIS activity within each directorate, which may include: production support; technical support; development activity; and other AIS effort.

Amarillo National Resource Center for Plutonium. Quarterly technical progress report, May 1, 1997--July 31, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Progress summaries are provided from the Amarillo National Center for Plutonium. Programs include the plutonium information resource center, environment, public health, and safety, education and training, nuclear and other material studies.

Lincoln County nuclear waste project. Quarterly progress report, October 1, 1991--December 31, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

This document included the following three progress reports to the Yucca Mountain Project Office on radioactive waste storage in Lincoln County, Nevada: financial status report; federal cash transactions report; and technical progress report.

Lincoln County nuclear waste project. Quarterly progress report, January 1, 1992--March 31, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

This document included the following three progress reports to the Yucca Mountain Project Office on radioactive waste storage in Lincoln County, Nevada: financial status report; federal cash transactions report; and technical progress report.

Lincoln County nuclear waste project quarterly progress report, April 1, 1992--June 30, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-03-01

This document included the following three progress reports to the Yucca Mountain Project Office on radioactive waste storage in Lincoln County, Nevada: financial status report; federal cash transactions report; and technical progress report.

Prototype solar heating and hot water systems

NASA Technical Reports Server (NTRS)

1978-01-01

Progress made in the development of a solar hot water and space heating system is described in four quarterly reports. The program schedules, technical status and other program activities from 6 October 1976 through 30 September 1977 are provided.

A study on the physical fitness index, heart rate and blood pressure in different phases of lunar month on male human subjects

NASA Astrophysics Data System (ADS)

Chakraborty, Ujjwal; Ghosh, Tusharkanti

2013-09-01

The gravitational pull of the moon on the earth is not the same in all phases of the lunar month, i.e. new moon (NM), first quarter (FQ), full moon (FM) and third quarter (TQ), and as a result the amplitude of tide differs in different phases. The gravitational pull of the moon may have effects on the fluid compartments of the human body and hence the cardiovascular system may be affected differentially in the different phases of the lunar month. In the present study resting heart rate (HR) and blood pressure (BP), physical fitness index (PFI), peak HR and BP immediately after step test, and recovery HR and BP after step test were measured during different phases of the lunar month in 76 male university students (age 23.7 ± 1.7 years). At rest, both systolic and mean arterial BP were ˜5 mmHg lower in NM and FM compared to FQ and TQ, but resting HR was not significantly different between phases. Further, peak HR and peak systolic BP after step test were lower (˜4 beat/min and ˜5 mmHg, respectively) in NM and FM compared to FQ and TQ. PFI was also higher (˜5) in NM and FM compared to FQ and TQ. Recovery of HR after step test was quicker in NM and FM compared to that of FQ and TQ. It appears from this study that gravitational pull of the moon may affect the cardiovascular functions of the human body. Moreover, the physical efficiency of humans is increased in NM and FM due to these altered cardiovascular regulations.

Environmental Hazards Assessment Program. Quarterly report, January 1994--March 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-05-04

The objectives of the EHAP program are to: Develop a holistic, national basis for risk assessment, risk management and risk communication; Develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects, and; Identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health oriented aspects of environmental restoration and waste management. This report describes activities and reports on progress for the third quarter of year two (January-March, 1994) of the grant. To better accomplish objectives, grant efforts are organized into three major elements: The Crossroadsmore » of Humanity Series; Research, Science and Education Programs; and Program Management. The Crossroads of Humanity Series charted a new course, incorporating lessons learned during previous quarters into a series of programs designed to address environmental issues in a real world setting. Reports are included on the various research programs with milestones and deliverables from the third quarter.« less

Monodisperse NixFe3-xO4 nanospheres: Metal-ion-steered size/composition control mechanism, static magnetic and enhanced microwave absorbing properties

NASA Astrophysics Data System (ADS)

Jiang, Kedan; Liu, Yun; Pan, Yefei; Wang, Ru; Hu, Panbing; He, Rujia; Zhang, Lingli; Tong, Guoxiu

2017-05-01

An easy metal-ion-steered solvothermal method was developed for the one-step synthesis of monodisperse, uniform NixFe3-xO4 polycrystalline nanospheres with tunable sphere diameter (40-400 nm) and composition (0 ≤ x ≤ 0.245) via changing just Ni2+/Fe3+ molar ratio (γ). With g increased from 0:1 to 2:1, sphere diameter gradually decreased and crystal size exhibited an inversed U-shaped change tendency, followed by increased Ni/Fe atom ratio from 0% to 0.0888%. An in situ-reduction, coordination-precipitation transformation mechanism was proposed to interpret the metal-ion-steered growth. Size- and composition-dependent static magnetic and microwave absorbing properties were systematically investigated. Saturation magnetization declines with g in a Boltzmann model due to the changes of crystal size, sphere diameter, and Ni content. The coercivity reaches a maximum at γ = 0.75:1 because of the critical size of Fe3O4 single domain (25 nm). Studies on microwave absorption reveal that 150-400 nm Fe3O4 nanospheres mainly obey the quarter-wavelength cancellation model with the single-band absorption; 40-135 nm NixFe3-xO4 nanospheres (0 ≤ x ≤ 0.245) obey the one and three quarter-wavelength cancellation model with the multi-band absorption. 150 nm Fe3O4 nanospheres exhibit the optimal EM wave-absorbing property with an absorbing band of 8.94 GHz and the maximum RL of -50.11 dB.

HAMS II Quarterly Progress Report (Technical and Financial)

DTIC Science & Technology

2015-01-09

Resistance - Flow Relationships .................................................................................. 10 Figure 3. Pulse Oximeter Front-end...19 Figure 10. Pulse Oximeter versus NIRS...TMS320C5515 DSP Medical Development Kit (MDK) for Pulse Oximeter Implementation. This evaluation system provides the capability to leverage into the

77 FR 18999 - New Mexico Collaborative Forest Restoration Program Technical Advisory Panel

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-29

... Collaborative Forest Restoration Program Technical Advisory Panel will meet in Albuquerque, New Mexico. The... the Hyatt Place Albuquerque/ Uptown, 6901 Arvada Avenue NE., Albuquerque, NM 87110, (505) 872-9000... Service, 333 Broadway SE., Albuquerque, NM 87102. Comments may also be sent via email to [email protected

75 FR 34973 - New Mexico Collaborative Forest Restoration Program Technical Advisory Panel

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-21

... Collaborative Forest Restoration Program Technical Advisory Panel will meet in Albuquerque, New Mexico. The... meeting will be held at the Hyatt Place Albuquerque/ Uptown, 6901 Arvada Avenue, NE., Albuquerque, NM... International Forestry Staff, USDA Forest Service, 333 Broadway SE., Albuquerque, NM 87102. Comments may also be...

Preliminary Results Obtained in Integrated Safety Analysis of NASA Aviation Safety Program Technologies

NASA Technical Reports Server (NTRS)

2005-01-01

This is a listing of recent unclassified RTO technical publications for January 1, 2005 through March 31, 2005 processed by the NASA Center for AeroSpace Center available on the NASA Aeronautics and Space Database. Contents include 1) Electronic Information Management; 2) Decision Support to Combined Joint Task Force and Component Commanders; 3) RTO Technical Publications : A Quarterly Listing (December 2004); 4) The Role of Humans in Intelligent and Automated Systems.

Scientific-Technical and Business Careers Training Grant

NASA Technical Reports Server (NTRS)

Conway, Mary P.

2001-01-01

The 1996 renewal of the NGT2-1001 grant included three objectives and expected outcomes. The information highlights the results and progress to address the grant objectives and outcomes for the time period of July 1, 2000 through June 30, 2001. Objective Number One indicated that the internship staff would annually recruit and place at least 90 community college students in internship positions related to their college majors. Internship enrollments for the summer, fall, winter and spring quarters of 2000-2001 show an average enrollment of 121 students per quarter. This number includes (13) interns sponsored by Ames contractors.

American Nursing's First Textbooks.

ERIC Educational Resources Information Center

Flaumenhaft, Eugene; Flaumenhaft, Carol

1989-01-01

Discusses the four textbooks, written in the last quarter of the 19th century, that shaped nursing in the United States. They provided technical information in a systematic fashion, established an autonomous literature that guided nurses in school and beyond, and defined the training school curriculum. (JOW)

Quarterly Performance/Technical Report of the National Marrow Donor Program

DTIC Science & Technology

2011-01-28

emergency notification system, the NMDP public announcement system, Government Emergency Telecommunications Service calling cards (GETS cards ), and the...Contract Audit Agency RCC Renal Cell Carcinoma DIY Do it yourself RCI BMT Resource for Clinical Investigations in Blood and Marrow Transplantation

16 CFR 1500.48 - Technical requirements for determining a sharp point in toys and other articles intended for use...

Code of Federal Regulations, 2010 CFR

2010-01-01

... Section 1500.48 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT...-quarter times the minor dimension of the probe, recess, or opening, measured from any point in the plane...

QUARTERLY TECHNICAL PROGRESS REPORT, JULY, AUGUST, SEPTEMBER 1966.

DTIC Science & Technology

Contents: Circuit research program; Hardware systems research; Software systems research program; Numerical methods, computer arithmetic and...artificial languages; Library automation; Illiac II service , use, and program development; IBM service , use, and program development; Problem specifications; Switching theory and logical design; General laboratory information.

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites - Quarterly Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Simmons, Kevin L.

This quarterly report summarizes the status for the project planning to initiate all the legal and contract documents required for establishing the subcontracts needed and a Cooperative Research and Development Agreement (CRADA) with Autodesk, Inc., Toyota Motor Engineering and Manufacturing North America (Toyota), and Magna Exterior and Interiors Corporation (Magna). During the first quarter (10/1/2012 to 12/31/2012), the statements of work (SOW) for the subcontracts to Purdue University, University of Illinois, and PlastiComp, Inc. were completed. A draft of the CRADA SOW was sent to Autodesk, Toyota, and Magna for technical and legal reviews. PNNL Legal Services contacted project partners’more » Legal counterparts for preparing legal documents for the project. A non-disclosure agreement was drafted and sent to all the parties for reviews.« less

Low cost hydrogen/novel membrane technology for hydrogen separation from synthesis gas, Phase 1. Quarterly technical progress report for the period ending March 31, 1986

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1986-12-31

The goal of this program is to develop polymer membranes useful in the preparation of hydrogen from coal-derived synthesis gas. During this quarter the first experiment were aimed at developing high performance composite membranes for the separation of hydrogen from nitrogen and carbon monoxide. Three polymers have been selected as materials for these membranes: polyetherimide cellulose acetate and ethylcellulose. This quarter the investigators worked on polyetherimide and cellulose acetate membranes. The overall structure of these membranes is shown schematically in Figure 1. As shown, a microporous support membrane is first coated with a high flux intermediate layer then with anmore » ultrathin permselective layer and finally, if necessary, a thin protective high flux layer. 1 fig., 4 tabs.« less

78 FR 16244 - New Mexico Collaborative Forest Restoration Program Technical Advisory Panel

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-14

... Collaborative Forest Restoration Program Technical Advisory Panel will meet in Albuquerque, New Mexico. The... at the Hyatt Place Albuquerque/ Uptown, 6901 Arvada Avenue NE., Albuquerque, NM 87110, (505) 872-9000... Service, 333 Broadway SE., Albuquerque, NM 87102. Comments may also be sent via email to [email protected

Thermal energy storage subsystems. A collection of quarterly reports

NASA Technical Reports Server (NTRS)

1978-01-01

The design, development, and progress toward the delivery of three subsystems is discussed. The subsystem used a salt hydrate mixture for thermal energy storage. The program schedules, technical data, and other program activities from October 1, 1976, through December 31, 1977 are presented.

Telescience Testbed Pilot Program

NASA Technical Reports Server (NTRS)

Gallagher, Maria L. (Editor); Leiner, Barry M. (Editor)

1988-01-01

The Telescience Testbed Pilot Program is developing initial recommendations for requirements and design approaches for the information systems of the Space Station era. During this quarter, drafting of the final reports of the various participants was initiated. Several drafts are included in this report as the University technical reports.

Agricultural Education--Instructional Materials.

ERIC Educational Resources Information Center

Ohio State Univ., Columbus. Center for Vocational and Technical Education.

This compilation presents over 950 resumes of instructional materials in agricultural education, which have appeared quarterly in "Abstracts of Instructional Materials in Vocational and Technical Education" (AIM), Fall 1967 through Fall 1971. Resumes cover a broad range of fields and occupations, such as agribusiness, agronomy, animal and plant…

Liquid fossil-fuel technology. Quarterly technical progress report, April-June 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Linville, B.

This report primarily covers in-house oil, gas, and synfuel research and lists the contracted research. The report is broken into the following areas: liquid fossil fuel cycle, extraction, processing, utilization, and project integration and technology transfer. BETC publications are listed. (DLC)

A CHARACTERIZATION AND EVALUATION OF COAL LIQUEFACTION PROCESS STREAMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

G.A. Robbins; R.A. Winschel; S.D. Brandes

This is the first Annual Technical Report of activities under DOE Contract No. DE-AC22-94PC93054. Activities from the first three quarters of the fiscal 1998 year were reported previously as Quarterly Technical Progress Reports (DOE/PC93054-57, DOE/PC93054-61, and DOE/PC93054-66). Activities for the period July 1 through September 30, 1998, are reported here. This report describes CONSOL's characterization of process-derived samples obtained from HTI Run PB-08. These samples were derived from operations with Black Thunder Mine Wyoming subbituminous coal, simulated mixed waste plastics, and pyrolysis oils derived from waste plastics and waste tires. Comparison of characteristics among the PB-08 samples was made tomore » ascertain the effects of feed composition changes. A comparison also was made to samples from a previous test (Run PB-06) made in the same processing unit, with Black Thunder Mine coal, and in one run condition with co-fed mixed plastics.« less

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2001-01-01

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information. Reports may be downloaded for free from the RTO website at http:/www.rta.nato.int or they may be purchased from the NASA Center for AeroSpace Information, 7121 Standard Drive, Hanover, MID 21076-1320 USA, phone 301-621-0390, fax 301-621-0134. Prices and order forms are available from the NASA STI website at http://www.sti.nasa.gov. An automatic distribution of unclassified RTO technical publications in CD-ROM is also available within the U.S. through the NASA Standing Order Service from the NASA Center for AeroSpace Information.

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2001-01-01

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information. Reports may be downloaded for free from the RTO website at http://www.rta.nato.int or they may be purchased from the NASA Center for AeroSpace Information, 7121 Standard Drive, Hanover, MD 21076-1320 USA, phone 301-621-0390, fax 301-621-0134. Prices and order forms are available from the NASA STI website at http://www.sti.nasa.gov. An automatic distribution of unclassified RTO technical publications in CD-ROM is also available within the US through the NASA Standing Order Service from the NASA Center for AeroSpace Information.

Demonstration of periodic nanostructure formation with less ablation by double-pulse laser irradiation on titanium

NASA Astrophysics Data System (ADS)

Furukawa, Yuki; Sakata, Ryoichi; Konishi, Kazuki; Ono, Koki; Matsuoka, Shusaku; Watanabe, Kota; Inoue, Shunsuke; Hashida, Masaki; Sakabe, Shuji

2016-06-01

By pairing femtosecond laser pulses (duration ˜40 fs and central wavelength ˜810 nm) at an appropriate time interval, a laser-induced periodic surface structure (LIPSS) is formed with much less ablation than one formed with a single pulse. On a titanium plate, a pair of laser pulses with fluences of 70 and 140 mJ/cm2 and a rather large time interval (>10 ps) creates a LIPSS with an interspace of 600 nm, the same as that formed by a single pulse of 210 mJ/cm2, while the double pulse ablates only 4 nm, a quarter of the ablation depth of a single pulse.

44 CFR 206.437 - State administrative plan.

Code of Federal Regulations, 2010 CFR

2010-10-01

... requests for advances of funds and reimbursement; (vii) Monitor and evaluate the progress and completion of... technical assistance as required to subgrantee(s); (xi) Comply with the administrative and audit requirements of 44 CFR parts 13 and 206; (xii) Provide quarterly progress reports to the Regional Administrator...

44 CFR 206.437 - State administrative plan.

Code of Federal Regulations, 2011 CFR

2011-10-01

... requests for advances of funds and reimbursement; (vii) Monitor and evaluate the progress and completion of... technical assistance as required to subgrantee(s); (xi) Comply with the administrative and audit requirements of 44 CFR parts 13 and 206; (xii) Provide quarterly progress reports to the Regional Administrator...

21st century locomotive technology: quarterly technical status report 26

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lembit Salasoo; Ramu Chandra

2009-08-24

Parasitic losses due to hybrid sodium battery thermal management do not significantly reduce the fuel saving benefits of the hybrid locomotive. Optimal thermal management trajectories were converted into realizable algorithms which were robust and gave excellent performance to limit thermal excusions and maintain fuel savings.

Applied Physics Modules Selected for Electrical and Electronic Technologies.

ERIC Educational Resources Information Center

Waring, Gene

Designed for individualized use in an applied physics course in postsecondary vocational-technical education, this series of twenty-three learning modules is equivalent to the content of two quarters of a five-credit hour class in electrical technology, electronic service technology, electronic engineering technology, or electromechanical…

CURA Reporter. Volume 37, Number 1, Spring 2007

ERIC Educational Resources Information Center

Greco, Michael D., Ed

2007-01-01

The "CURA Reporter" is published quarterly to provide information about the Center for Urban and Regional Affairs (CURA), an all-University applied research and technical assistance center at the University of Minnesota that connects faculty and students with community organizations and public institutions working on significant public…

CURA Reporter. Volume 36, Number 1, Spring 2006

ERIC Educational Resources Information Center

Greco, Michael D., Ed.

2006-01-01

The "CURA Reporter" is published quarterly to provide information about CURA an all-University applied research and technical assistance center at the University of Minnesota that connects faculty and students with community organizations and public institutions working on significant public policy issues in Minnesota. Items in this…

78 FR 22332 - Notice of Quarterly Report (October 1, 2012-December 31, 2012)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-15

... applied improved techniques. Agro-sylvo-pastoral groups that receive technical assistance. Loans provided... Administration \\3\\ and $56,138,545 $34,820,809 Control, Monitoring and Evaluation. Pending Subsequent Report \\4...,435 Control, Monitoring and Evaluation. Pending Subsequent Report \\4\\ Cumulative Projects Obligated...

Network Resources and Training Site at Elizabeth City State University

NASA Technical Reports Server (NTRS)

Hayden, Linda Bailey

1996-01-01

The format of the annual report follows the same format as the quarterly report. In the annual report Elizabeth City State University (ECSU) has included responses to the items listed in the 'Critique of Quarterly Report Summary, and the 'Technical Recommendations for Consideration to NRTS/ECSU'. A budget for FY96-97 is included requesting $500,000.00 to cover the operating expenses of the Network Resources Training Site (NRTS) and its current partners as outlined in the original grant. The final attachment is a proposal to expand the partnerships and services of the NRTS at ECSU. This proposal would increase the number of predominantly minority attended secondary schools that this NRTS services and to support participation of these secondary schools in the GLOBE, ATLAS and Skymath projects. The proposal would also make Bennett College a full partner in the NRTS and it would increase the networking funds available to Virginia State University (HBCU/MI partner). Funds to increase the NRTS staff size to support the new partners and extended services is included in the extension budget. The NRTS Office Staff provides training and technical expertise to all its partners. In the appendix of the report, you will find technical soundness questionnaires and campus LAN Diagrams for the HBCU/MI Partners.

Advanced direct coal liquefaction concepts. Quarterly report, July 1--September 30, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berger, D.J.; Parker, R.J.; Simpson, P.L.

All the reports required for completion of the contract were submitted this quarter. A proposal for further work in Phase 2 was also submitted. The technical and economic assessment of the process was completed. The results show that for the base case scenario (25% equity, 15% after tax DCF-ROE) coal derived synthetic crude oil can be produced at just below US $30 per barrel. The study was based on the production of 75,000 BPD of C{sub 4+} synthetic crude oil from Black Thunder coal for subsequent processing in a conventional petroleum refinery from Black Thunder (Wyoming) subbituminous coal.

The AMTEX Partnership. Third quarterly report, FY 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lemon, D.K.; Quisenberry, R.K.

1995-06-01

Key activities for the quarter were the initiation of tactical work on the OPCon Project, development of a draft of the AMTEX Policies and Procedures document, and a meeting of the Industry Technical Advisory Committee. A significant milestone was reached when a memorandum of understanding was signed between the DOE and The Department of Commerce. The agreement signified the official participation of the National Institute of Standards and Technology on the Demand Activated Manufacturing Architecture (DAMA) project in AMTEX. Project accomplishments are given for: computer-aided manufacturing, cotton biotechnology, DAMA, electronic embedded fingerprints, rapid cutting, sensors for agile manufacturing, and textilemore » resource conservation.« less

CURA Reporter. Volume 40, Numbers 1-2, Spring/Summer 2010

ERIC Educational Resources Information Center

Greco, Michael D., Ed.

2010-01-01

The "CURA Reporter" is published quarterly to provide information about the Center for Urban and Regional Affairs (CURA), an all-University applied research and technical assistance center at the University of Minnesota that connects faculty and students with community organizations and public institutions working on significant public…

Individual-Based Completion Rates for Apprentices. Technical Paper

ERIC Educational Resources Information Center

Karmel, Tom

2011-01-01

Low completion rates for apprentices and trainees have received considerable attention recently and it has been argued that NCVER seriously understates completion rates. In this paper Tom Karmel uses NCVER data on recommencements to estimate individual-based completion rates. It is estimated that around one-quarter of trade apprentices swap…

Applied Physics Modules Selected for Manufacturing and Metal Technologies.

ERIC Educational Resources Information Center

Waring, Gene

Designed for individualized use in an applied physics course in postsecondary vocational-technical education, this series of eighteen learning modules is equivalent to the content of two quarters of a five-credit hour class in manufacturing engineering technology, machine tool and design technology, welding technology, and industrial plastics…

A Short-Term Forecasting Procedure for Institution Enrollments.

ERIC Educational Resources Information Center

Pfitzner, Charles Barry

1987-01-01

Applies the Box-Jenkins time series methodology to enrollment data for the Virginia community college system. Describes the enrollment data set, the Box-Jenkins approach, and the forecasting results. Discusses the value of one-quarter ahead enrollment forecasts and implications for practice. Provides a technical discussion of the model. (DMM)

MAHFIL: A Quarterly of South Asian Literature, Spring-Summer 1971.

ERIC Educational Resources Information Center

Coppola, Carlo, Ed.

This volume contains both literature from South Asia and articles about South Asian literature. The first article consists of an interview with a leading Pakistani poet, N.M. Rashed, who discusses modern Urdu literature. Other articles are: "Five 'Dangerous' Books"--on censorship in East Pakistan--by P. Sarkar; "Baluchi Language and…

IR Window Studies

DTIC Science & Technology

1974-06-15

Inclusion Damage in the Failure of lO.ö^m Optics 3. DISCUSSION i 1 2 3 16 22 27 28 39 42 59 68 74 85 94 ill "--■ p«nm# upi» w >, ami ...Rockwell, T. S. Colbert During this quarter our research effort included the application of acoustic surface wave techniques to measure the depth

Observation of parametric instabilities in the quarter critical density region driven by the Nike KrF laser

NASA Astrophysics Data System (ADS)

Weaver, J. L.; Oh, J.; Phillips, L.; Afeyan, B.; Seely, J.; Kehne, D.; Brown, C. M.; Obenschain, S. P.; Serlin, V.; Schmitt, A. J.; Feldman, U.; Lehmberg, R. H.; Mclean, E.; Manka, C.

2013-02-01

The krypton-fluoride (KrF) laser is an attractive choice for inertial confinement fusion due to its combination of short wavelength (λ =248 nm), large bandwidth (up to 3 THz), and superior beam smoothing by induced spatial incoherence. These qualities improve the overall hydrodynamics of directly driven pellet implosions and should allow use of increased laser intensity due to higher thresholds for laser plasma instabilities when compared to frequency tripled Nd:glass lasers (λ =351 nm). Here, we report the first observations of the two-plasmon decay instability using a KrF laser. The experiments utilized the Nike laser facility to irradiate solid plastic planar targets over a range of pulse lengths (0.35 ns≤τ≤1.25 ns) and intensities (up to 2×1015 W/cm2). Variation of the laser pulse created different combinations of electron temperature and electron density scale length. The observed onset of instability growth was consistent with the expected scaling that KrF lasers have a higher intensity threshold for instabilities in the quarter critical density region.

Quarterly technical progress report, February 1, 1996--April 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This report from the Amarillo National REsource Center for PLutonium provides research highlights and provides information regarding the public dissemination of information. The center is a a scientific resource for information regarding the issues of the storage, disposition, potential utilization and transport of plutonium, high explosives, and other hazardous materials generated from nuclear weapons dismantlement. The center responds to informational needs and interpretation of technical and scientific data raised by interested parties and advisory groups. Also, research efforts are carried out on remedial action programs and biological/agricultural studies.

Quarterly literature review of the remote sensing of natural resources

NASA Technical Reports Server (NTRS)

Fears, C. B. (Editor); Inglis, M. H. (Editor)

1977-01-01

The Technology Application Center reviewed abstracted literature sources, and selected document data and data gathering techniques which were performed or obtained remotely from space, aircraft or groundbased stations. All of the documentation was related to remote sensing sensors or the remote sensing of the natural resources. Sensors were primarily those operating within the 10 to the minus 8 power to 1 meter wavelength band. Included are NASA Tech Briefs, ARAC Industrial Applications Reports, U.S. Navy Technical Reports, U.S. Patent reports, and other technical articles and reports.

Demonstration of periodic nanostructure formation with less ablation by double-pulse laser irradiation on titanium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Furukawa, Yuki; Graduate School of Science, Kyoto University, Kitashirakawa, Sakyo, Kyoto 606-8502; Advanced Research Center for Beam Science, Institute for Chemical Research, Kyoto University, Gokasho, Uji, Kyoto 611-0011

By pairing femtosecond laser pulses (duration ∼40 fs and central wavelength ∼810 nm) at an appropriate time interval, a laser-induced periodic surface structure (LIPSS) is formed with much less ablation than one formed with a single pulse. On a titanium plate, a pair of laser pulses with fluences of 70 and 140 mJ/cm{sup 2} and a rather large time interval (>10 ps) creates a LIPSS with an interspace of 600 nm, the same as that formed by a single pulse of 210 mJ/cm{sup 2}, while the double pulse ablates only 4 nm, a quarter of the ablation depth of a single pulse.

AFWAL FY81 Technical Accomplishments.

DTIC Science & Technology

1982-04-01

SO Navier-Stokes Nozzle Computation.................................................... 51 KC-135 Winglet ... blending and provide pilot has been completed. The potential military significance utility in TAC simulation at Luke AFB. Simulation * of this task is all...evaluation other than rear quarter attack. The advanced gunsights of the complete blended system. should also be implemented at lower cost and give

Antenna Construction & Propagation of Radio Waves, 5-1. Military Curriculum Materials for Vocational and Technical Education.

ERIC Educational Resources Information Center

Marine Corps, Washington, DC.

These military-developed curriculum materials consist of five individualized, self-paced chapters dealing with antenna construction and propagation of radio waves. Covered in the individual lessons are the following topics: basic electricity; antenna transmission-line fundamentals; quarter-wave antennas, half-wave antennas, and associated radio…

Schedules, technical status, and program activities in the development of a single family solar space heating system

NASA Technical Reports Server (NTRS)

1978-01-01

A collection of three quarterly reports are given covering the development of two prototype solar heating systems consisting of the following subsystems: collector, storage, control, transport, and site data acquisition. The two systems are being installed at York, Pennsylvania, and Manchester, New Hampshire.

Nuclear Energy Research Initiative (NERI) Program. 2nd Quarterly Technical Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

2000-02-22

The research activities have been underway. We have located a large body of source material from aerospace, shipbuilding and manufacturing businesses that is serving the basis for identifying improvement methodologies. Our work on developing the three models proposed to capture the extent of the improvement possibilities has been ongoing.

Preliminary Results Obtained in Integrated Safety Analysis of NASA Aviation Safety Program Technologies

NASA Technical Reports Server (NTRS)

2000-01-01

This is a quarterly listing of unclassified AGARD and RTO technical publications NASA received and announced in the NASA STI Database. Contents include 1) Sensor Data Fusion and Integration of the Human Element; 2) Planar Optical Measurement Methods for Gas Turbine Components; 3) RTO Highlights 1998, December 1998.

[The supply chain is everybody's business...].

PubMed

Coulondre, Antoine

2007-05-01

The management of the supply chain is a matter of delicate balance. This is certainly due to its position at the crossroads between suppliers and users requirements, as well as logistic, financial and technical regulations. For a public organisation like EFS, whose annual budget amounts to 697 million euros, there is a lot at stake: supplies represent the second most important item of its budget accounting for 38% of annual expenses. Three quarters of the purchases concern basic activities such as blood collection, testing procedures, transformation and distribution of blood products. The last quarter is spent on more general activities (computer systems, telecommunications...). Professionalisation of the purchasing function has grown since the creation of the government-owned organisation as a single national unit (EFS) in the year 2000. Its consequences can be felt especially in the field of the "core activities". The current stage consists in maintaining close links between all the skills necessary to a high-quality supply chain. The latter will undoubtedly be beneficial to the medical, technical and support departments of EFS, which are the in-house customers to satisfy.

USE OF COAL DRYING TO REDUCE WATER CONSUMED IN PULVERIZED COAL POWER PLANTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edward Levy; Harun Bilirgen; Ursla Levy

2006-01-01

This is the twelfth Quarterly Report for this project. The background and technical justification for the project are described, including potential benefits of reducing fuel moisture using power plant waste heat, prior to firing the coal in a pulverized coal boiler. During this last Quarter, the development of analyses to determine the costs and financial benefits of coal drying was continued. The details of the model and key assumptions being used in the economic evaluation are described in this report and results are shown for a drying system utilizing a combination of waste heat from the condenser and thermal energymore » extracted from boiler flue gas.« less

FETC/EPRI Biomass Cofiring Cooperative Agreement. Quarterly technical report, April 1-June 30, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hughes, E.; Tillman, D.

1997-12-01

The FETC/EPRI Biomass Cofiring Program has accelerated the pace of cofiring development by increasing the testing activities plus the support activities for interpreting test results. Past tests conducted and analyzed include the Allen Fossil Plant and Seward Generating Station programs. On-going tests include the Colbert Fossil Plant precommercial test program, the Greenidge Station commercialization program, and the Blount St. Station switchgrass program. Tests in the formative stages included the NIPSCO cofiring test at Michigan City Generating Station. Analytical activities included modeling and related support functions required to analyze the cofiring test results, and to place those results into context. Amongmore » these activities is the fuel availability study in the Pittsburgh, PA area. This study, conducted for Duquesne Light, supports their initial investigation into reburn technology using wood waste as a fuel. This Quarterly Report, covering the third quarter of the FETC/EPRI Biomass Cofiring Program, highlights the progress made on the 16 projects funded under this cooperative agreement.« less

Ambient and laboratory measurements of ice nuclei and their biological faction with the Fast Ice Nuclei CHamber FINCH-HALO using the new 405nm Version of the BIO-IN Sensor

NASA Astrophysics Data System (ADS)

Bundke, U.; Nillius, B.; Bingemer, H.; Curtius, J.

2012-04-01

We have designed the BIO-IN detector as part of the ice nucleus counter FINCH (Fast Ice Nuclei CHamber counter) to distinguish activated Ice Nuclei (IN) ice crystals from water droplets (CCN) (Bundke et al. 2008) and their fraction of biological origin (Bundke 2010). The modified BIO-IN sensor illuminates an aerosol stream with a 405 nm laser, replacing a 365nm LED of the original BIO IN design. Particles will scatter the light and those of biological origin will show intrinsic fluorescence emissions by excitation of mainly Riboflavin, also known as vitamin B2. The incident laser light is circularly polarized by introducing a quarter-wave-plate. The circular depolarization ratio (p44/p11) of the scattering matrix is measured in the backward direction by two photomultipliers at 110° scattering angle using a combination of quarter-wave-plate and a beam splitting cube to analyze the two circular polarization components. The detection limit was lowered towards particle size of about 400nm diameter (non activated particles). It is now possible to calculate the activated fraction of IN of biological origin with respect to all biological particles measured with one detector. The performance of the sensor will be demonstrated showing the circular- depolarization properties of different test aerosol, dust samples, volcanic ashes as well as different biological particles. Measurements on the mountain Puy de Dôme of IN number concentration of ambient air, as well as measurements at the AIDA facility in Karlsruhe of the IN activation curves from different bacteria are shown. Acknowledgements: This work was supported by the German Research Foundation, Grant: BU 1432/3-2 BU 1432/4-1

Deliberate Science, Continuum Magazine: Clean Energy Innovation at NREL, Winter 2012 (Book)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2012-02-01

This quarterly magazine is dedicated to stepping beyond the technical journals to reveal NREL's vital work in a real-world context for our stakeholders. Continuum provides insights into the latest and most impactful clean energy innovations, while spotlighting those talented researchers and unique facilities that make it all happen. This edition focuses on deliberate science.

The Open Door, A Quarterly Journal of the North Carolina Department of Community Colleges.

ERIC Educational Resources Information Center

The Open Door, 1968

1968-01-01

This issue contains articles on the state's opportunities in technical education and the need for making them known to more students, teachers, and counselors. The contents are: (1) an editorial on the success and satisfactions of engineering technology graduates; (2) the place of the technician in industry, a description of courses available, and…

Science and Technology Community in Crisis

DTIC Science & Technology

2002-05-01

centralized, highly bureaucratic, support system that considers itself an end, a point noted in the management literature by Peter Drucker :48 “What...Review Quarterly, Spring 2000. 48 Drucker , Peter F., Management : Tasks, Responsibilities, Practices, Apr 1993. 43 regionalization of personnel...technical areas as information technology, biotechnology, nanotechnology, etc. Peter Drucker , the well-known management expert once commented: “In

Space Communications

DTIC Science & Technology

1977-06-15

MASSACHUSETTS INSTITUTE OF TECHNOLOGY LINCOLN LABORATORY SPACE COMMUNICATIONS QUARTERLY TECHNICAL SUMMARY REPORT TO THE AIR FORCE...Massachusetts Institute of Technology, with the support of the Department of the Air Force under Contract F19628-76-C-0002. This report may be...four areas: support of communications-link testing by outside agencies, cooperative jamming tests, bit-error-rate measurements on the Air Force

HAMS (Hypoxia, Monitoring, and Mitigation System) II Quarterly Progress Report (Technical and Financial)

DTIC Science & Technology

2015-04-10

Peripheral Interface SpO2 Arterial Oxygen Saturation Measured via Pulse - Oximeter SRS Software Requirements Specification SV Stroke Volume SVR Systemic...viewer ....................................................................................................... 9 Figure 3: Pulse OX custom module...analysis approaches will be gathered. Sensors which detect SpO2, pulse / pulse rate, ECG, and skin temperature will be researched and evaluated for

Career and Technical Education. National Dropout Prevention Center/Network Newsletter. Volume 20, Number 3

ERIC Educational Resources Information Center

Duckenfield, Marty, Ed.

2008-01-01

The "National Dropout Prevention Newsletter" is published quarterly by the National Dropout Prevention Center/Network. This issue contains the following articles: (1) Why Do I Have to Learn This?; (2) 2008 NDPN Crystal Star Winners; (3) Effective Freshman Transition for School Improvement (David Livingston, John Greene, and Lindy Stahlman); (4)…

The Next 25 Years?: Future Scenarios and Future Directions for Education and Technology

ERIC Educational Resources Information Center

Facer, K.; Sandford, R.

2010-01-01

The educational technology research field has been at the heart of debates about the future of education for the last quarter century. This paper explores the socio-technical developments that the next 25 years might bring and the implications of such developments for educators and for educational technology research. The paper begins by outlining…

Empowering Accountability for Vocational-Technical Education: The Analysis and Use of Wage Records.

ERIC Educational Resources Information Center

Jarosik, Daniel; Phelps, L. Allen

Since 1988, state governments have been required to collect quarterly from private sector employers gross earnings by Social Security numbers, industry of employment, and county of employment. A study was conducted of 13 states' efforts to use this wage record database as a tool for improving educational accountability and assessing the impact of…

21st Century Locomotive Technology: Quarterly Technical Status Report 28

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lembit Salasoo; Ramu Chandra

2010-02-19

Thermal testing of a subscale locomotive sodium battery module was initiated.to validate thermal models. The hybrid trip optimizer problem was formulated. As outcomes of this project, GE has proceeded to commercialize trip optimizer technology, and has initiated work on a state-of-the-art battery manufacturing plant for high energy density, sodium-based batteries.

Educational Technology Program. Quarterly Technical Summary, 1 December 1970 through 28 February 1971.

ERIC Educational Resources Information Center

Frick, Frederick C.

The decision to employ direct rather than diffraction recording in the Lincoln Training System (LTS) is reported. This resulted from the findings that direct recording was practical at higher densities than previously thought possible and that rapid access to a number of fiche would compensate for the limited number of frames per fiche realized…

Educational Technology Program. Quarterly Technical Summary, 1 March - 31 May 1972.

ERIC Educational Resources Information Center

Frick, Frederick C.

The results of the field trials of the Lincoln Training System (LTS-3) program are summarized in this report. The LTS-3 system was designed to teach basic electronics to Air Force personnel at Kessler Air Force Base, Mississippi. The results indicated that the instructional delays due to system failure were minimal, and those failures were…

NASA Sun-Earth Connections Theory Program: The Structure and Dynamics of the Solar Corona and Inner Heliosphere

NASA Technical Reports Server (NTRS)

Mikic, Zoran; Grebowsky, Joseph (Technical Monitor)

2001-01-01

This report covers technical progress during the first quarter of the second year of NASA Sun-Earth Connections Theory Program (SECTP). SAIC and the University of California, Irvine (UCI) have conducted research into theoretical modeling of active regions, the solar corona, and the inner heliosphere, using the MHD model.

Measurement of solids motion in gas-fluidized beds. Technical progress report, 1 October 1982-31 December 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, M.M.; Chao, B.T.

This technical progress report covers the progress made during the fifth quarter of the project entitled Measurements of Solids Motion in Gas Fluidized Beds under Grant No. DOE-F22-81PC40804 during the period 1 October through 31 December 1982. The research concerns the measurement of solids particle velocity distribution and residence time distribution using the Computer-Aided Particle Tracking Facility (CAPTF) at the University of Illinois at Urbana-Champaign. The experimental equipment and measuring methods used to determine particle size distribution and particle motion and the results obtained are presented.

Educational Technology Program. Quarterly Technical Summary Report, 1 December 1971-29 February 1972.

ERIC Educational Resources Information Center

Frick, Frederick C.

The Lincoln Training System (LTS-3) is a computer-assisted instructional system for training Air Traffic Controllers and Basic Electronic students in the United States Air Force. This document describes the components of the system prior to its initial field trial in mid-April 1972 at Kessler Air Force Base. The system is made up of 14 Basic…

Center for Information Services Fourth Quarterly Progress Report, Phase IIB; Detailed Design and Prototype Development, 1 October 1971 to 31 December 1971.

ERIC Educational Resources Information Center

Kehl, W. B.; And Others

The administrative activity, including organization, staff, budget and external contacts, and the technical progress of IPS development, experimental service, workshops, documentation and related activities of the Center for Information Services (at the University of California, Los Angeles) are reported upon in this document. Pages 9 and 10 may…

Space Communications

DTIC Science & Technology

1977-03-15

Current capabilities of solid-state power devices (IMPATTs, bipolar, and field- effect tran- sistors) have been reviewed with regard to use in space ...Quarterly Technical Summary CO CD > -n_ or CJ> Space Communications Prepared for the Department of the Air Force under Electronic Systems...document when it is no longer needed. mm .■ ■■■ ■ ■ MASSACHUSETTS INSTITUTE OF TECHNOLOGY LINCOLN LABORATORY SPACE COMMUNICATIONS

Evolution of Technical Writing in Senior Design--A Case History

ERIC Educational Resources Information Center

Gnanapragasam, Nirmala

2010-01-01

Seattle University has an industrially sponsored, yearlong, senior design program that has been in existence for more than 20 years. Students work in teams of three or four under the guidance of a liaison from the sponsoring agency and a faculty advisor. The students prepare a proposal in the fall quarter detailing their plan and a design report…

Lean Six Sigma in Healthcare: Combating the Military’s Escalating Pharmacy Costs

DTIC Science & Technology

2009-04-30

Management journal . Prior to his career in academia, Dr. Apte worked for over ten years in managing operations and information systems in the financial... journals including Management Science, Interfaces, Production and Operations Management , Journal of Operations Management , Decision Sciences, IIE...Telecommunication Management , Naval Logistics Quarterly, and other technical journals and conference proceedings. He has been involved in

Cyberspace, the 7th Joint Function for 21st Century Warfare

DTIC Science & Technology

2017-03-31

such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research, special, group study, etc . 3. DATE COVERED...procedures, e.g. RD/FRD, PROPIN, ITAR, etc . Include copyright information. 13. SUPPLEMENTARY NOTES. Enter information not included...elsewhere such as: prepared in cooperation with; translation of; report supersedes; old edition number, etc . 14. ABSTRACT. A brief (approximately

KEEP Reading Research and Instruction: Results of the 1973-74 Program. Technical Report No. 26.

ERIC Educational Resources Information Center

Au, Kathryn H.; Speidel, Gisela E.

This report summarizes research related to the use of a conventional basal reading program with students in the Kamehameha Early Education Program (KEEP). Results of instruction were measured by the number of objectives gained each quarter, the total number of objectives gained, the number of lessons taken for each objective, and scores on the…

SUSTAINABLE ALLOY DESIGN: SEARCHING FOR RARE EARTH ELEMENT ALTERNATIVES THROUGH CRYSTAL ENGINEERING

DTIC Science & Technology

2016-02-26

Property Maps to Guide Materials Design via Statistical Learning Summer Research Group Meeting – Materials by Design Los Alamos National Laboratory, July...Informatics, Rational design , Quantitative correlative spectroscopy and imaging, DFT, In situ high pressure mechanical property measurements, Superalloy...final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED. Indicate the

Datacomputer and Sip Operations

DTIC Science & Technology

1977-03-31

IO PUBLIC T~LLINOVI 198 DISTRIBJTIONUINIMITED-3 LJSubmitted to: Defense Advanced Research Projects Agency 1400 Wilson Boulevard Arlington, Virginia...Quarterly Technical Report January 1, 1977 to March 31, 1977 This research is supported by the Defense Advanced Research Projects Agency of the Department of...necessarily representing the official policies, either expressed or implied, of the Defense Advanced Research Projects Agency or the U.S. Government

Extensible Adaptive System for STEM Learning

DTIC Science & Technology

2013-07-16

Copyright 2013 Raytheon BBN Technologies Corp. All Rights Reserved ONR STEM Grand Challenge Extensible Adaptive System for STEM Learning ...Contract # N00014-12-C-0535 Raytheon BBN Technologies Corp. (BBN) Reference # 14217 In partial fulfillment of contract deliverable item # A001...Quarterly Progress Report #2 April 7, 2013 –July 6, 2013 Submitted July 16, 2013 BBN Technical POC: John Makhoul Raytheon BBN Technologies

Publications of the Jet Propulsion Laboratory 1989

NASA Technical Reports Server (NTRS)

1990-01-01

This bibliography describes and indexes by primary author the externally distributed technical reporting, released during 1989, that resulted from scientific and engineering work performed, or managed, by JPL. Three classes of publications are included: JPL publications in which the information is complete for a specific accomplishment; articles from the quarterly Telecommunications and Data Acquisition (TDA) Progress Report; and articles published in the open literature.

Out Brief for the Structural Reliability Partnership Workshop

DOE Office of Scientific and Technical Information (OSTI.GOV)

Boyce, Brad; Fang, Eliot; Kolski, Alyssa

The Structural Reliability Partnership Workshop was held in Albuquerque, NM on August 29-30, 2017 and was hosted by Sandia National Laboratories. Attendees were present from academia, industry and several other national laboratories. The workshop kicked off with an introduction to the SRP to familiarize potential members with what the purpose, structure and benefits would be to their organization. Technical overviews were given on several topics by attendees from each sector – national labs, universities and industry – to provide a snapshot of the type of work that is currently being conducted on structural reliability. Attendees were then given the opportunitymore » to suggest and discuss potential Challenge Scenario topics. Three were ultimately decided upon as being the most important: Additive Manufacturing, Hydrogen Pipeline Steels, and Bolted Joined Structures. These were then analyzed using Quad Charts to determine What, How, Who, and Why these areas would be further investigated. Rather than restricting future research to only one area, the option was left open to investigate both the top two, depending on interest and cost associated with hosting such an event. More informal collaboration may be undertaken for the third topic if members have time and interest. Other items discussed pertained to the organization, structure and policies of the Partnership. Topics including Data Management, IP, and mechanisms of partnering/information sharing were touched upon but final decisions were not made. Further action is needed before this can be done. Action items were outlined and assigned, where possible. The next workshop is to be held in early August 2018 in Boulder, CO and is to be hosted by NIST. In the interim, quarterly updates are to take place via WebEx to maintain a line of communication and to ensure progress on both the administrative and technical tasks.« less

Metallic metasurfaces for high efficient polarization conversion control in transmission mode.

PubMed

Li, Tong; Hu, Xiaobin; Chen, Huamin; Zhao, Chen; Xu, Yun; Wei, Xin; Song, Guofeng

2017-10-02

A high efficient broadband polarization converter is an important component in integrated miniaturized optical systems, but its performances is often restricted by the material structures, metallic metasurfaces for polarization control in transmission mode never achieved efficiency above 0.5. Herein, we theoretically demonstrate that metallic metasurfaces constructed by thick cross-shaped particles can realize a high efficient polarization transformation over a broadband. We investigated the resonant properties of designed matesurfaces and found that the interaction between double FP cavity resonances and double bulk magnetic resonances is the main reason to generate a high transmissivity over a broadband. In addition, through using four resonances effect and tuning the anisotropic optical response, we realized a high efficient (> 0.85) quarter-wave plate at the wavelength range from 1175nm to 1310nm and a high efficient (> 0.9) half-wave plate at the wavelength range from 1130nm to 1230nm. The proposed polarization converters may have many potential applications in integrated polarization conversion devices and optical data storage systems.

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This report summarizes system performance and major project activities over the first four months of 1995. The quarterly technical reports that have been issued for the past several years are being replaced this year by two technical reports covering the January--April and May--August periods, respectively. Performance data for the last four months of the year will be included in the 1995 Progress Report. Principal activities during the first four months of 1995 included bringing two new systems on line, hosting a two-day Balance of System and Procurement workshop at the Davis site, completing and issuing the EMT Five-Year Assessment Report,more » and preparing for a management transition in 1996.« less

Research on solvent-refined coal. Quarterly technical progress report, July 1-September 30, 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1982-07-01

This report describes progress on the Research on Solvent Refined Coal project by The Pittsburg and Midway Coal Mining Company's Merriam Laboratory during the third quarter of 1981. A four-part experiment was conducted with subbituminous Edna coal, pyrite and/or bituminous Ireland coal at 457/sup 0/C and 1800 psig or 450/sup 0/C and 2250 psig. The purpose was to determine the conditions appropriate for processing a 50/50 by weight blend of these coals. A total of four runs (11 experiments) discussed this quarter were directed toward the study of disposable catalysts. Subbituminous coals from the Edna and Belle Ayr Mines weremore » processed in the SRC II mode. Additives investigated were pyrite, ferric oxide, molybdenum doped ferric oxide and iron dispersed on silica-alumina. The level and type of sulfur added in conjunction with ferric oxide catalysts was also explored as well as addition of sulfur by itself. Two solvent hydrogenation runs and five SRC I runs were directed toward a preliminary investigation of short residence time processing of western (Belle Ayr) coals.« less

USE OF COAL DRYING TO REDUCE WATER CONSUMED IN PULVERIZED COAL POWER PLANTS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Edward Levy; Nenad Sarunac; Harun Bilirgen

2005-04-01

This is the ninth Quarterly Report for this project. The background and technical justification for the project are described, including potential benefits of reducing fuel moisture using power plant waste heat, prior to firing the coal in a pulverized coal boiler. During this last Quarter, comparative analyses were performed for lignite and PRB coals to determine how unit performance varies with coal product moisture. Results are given showing how the coal product moisture level and coal rank affect parameters such as boiler efficiency, station service power needed for fans and pulverizers and net unit heat rate. Results are also givenmore » for the effects of coal drying on cooling tower makeup water and comparisons are made between makeup water savings for various times of the year.« less

The Structure and Dynamics of the Solar Corona and Inner Heliosphere

NASA Technical Reports Server (NTRS)

Mikic, Zoran; Grebowsky, J. (Technical Monitor)

2001-01-01

This report covers technical progress during the third quarter of the second year of NASA Sun-Earth Connections Theory Program (SECTP) contract 'The Structure and Dynamics of the Solar Corona and Inner Heliosphere,' NAS5-99188, between NASA and Science Applications International Corporation, and covers the period February 16, 2001 to May 15, 2001. Under this contract SAIC and the University of California, Irvine (UCI) have conducted research into theoretical modeling of active regions, the solar corona, and the inner heliosphere, using the MHD model.In this report we summarize the accomplishments made by our group during the first seven quarters of our Sun-Earth Connection Theory Program contract. The descriptions are intended to illustrate our principal results. A full account can be found in the referenced publications.

Writing: the Quarterly as text.

PubMed

Locke, Lawrence F

2005-06-01

The purpose of this essay is to examine how writing has shaped the nature of the Quarterly over 75 years. Here I explore how stylistic elements have changed over time, how form has interacted with function and content, and how well the resulting text has served the several communities within physical education. I make the following assertions. First, the writing style that has become the model for research reports is needlessly dense and daunting for readers. Second, the desire to maintain a journal that serves both as an interdisciplinary resource for a broad audience of physical educators and as an outlet for reports directed to limited audiences of technical specialists has prevented full performance of either function. Those concerns notwithstanding, I find good cause for celebration--as well as for guarded optimism about the future.

Utility-Scale Future, Continuum Magazine: Clean Energy Innovation at NREL, Spring 2011, Issue 1 Vol. 1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

2011-08-01

This quarterly magazine is dedicated to stepping beyond the technical journals to reveal NREL's vital work in a real-world context for our stakeholders. Continuum provides insights into the latest and most impactful clean energy innovations, while spotlighting those talented researchers and unique facilities that make it all happen. This edition focuses on creating a utility-scale future.

Scoping of Flood Hazard Mapping Needs for Coos County, New Hampshire

DTIC Science & Technology

2006-01-01

Technical Partner DEM Digital Elevation Model DFIRM Digital Flood Insurance Rate Map DOQ Digital Orthophoto Quadrangle DOQQ Digital Ortho Quarter Quadrangle...color Digital Orthophoto Quadrangles (DOQs)). Remote sensing, base map information, GIS data (for example, contour data, E911 data, Digital Elevation...the feature types found on USGS topographic maps. More recently developed data were derived from digital orthophotos providing improved base map

Responsive copolymers for enhanced petroleum recovery. Quarterly technical progress report, December 21, 1994--March 22, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCormick, C.; Hester, R.

The purpose of this study is to extend the concept of micellar polymerization to more complex systems, and to explore the responsive nature of hydrophobically modified polyelectrolytes by tailoring the microstructure. The synthesis of hydrophobically modified acrylamide/acrylic acid copolymer is described. These types of polymers are of interest as thickening agents utilized in enhanced oil recovery.

Systems study of fuels from grains and grasses. Quarterly progress report, July--October 1976

DOE Office of Scientific and Technical Information (OSTI.GOV)

Benson, W.; Allen, A.; Athey, R.

1976-11-15

The specific objectives of the project are to determine on a geographic basis the current and potential USA production capability for grain and grass crops, to perform a preliminary screening of conversion processes, and to perform preliminary technical and economic feasibility analyses. The results obtained to date on biomass production, conversion processes, and data management are reported. (JSR)

Quantum Manybody Physics with Rydberg Polaritons

DTIC Science & Technology

2016-06-22

report, such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED...for public release. Over the course of this grant, we have seen tremendous progress, both theoretically and experimentally , in our control of photonic...shown in multiple stages of construction at left and below, spans three optical tables in two rooms: One for the experimental control system

Combinational Optimal Stopping Problems

DTIC Science & Technology

2016-04-01

such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED...Vinel, A. and P. Krokhmal (2015) Certainty equivalent measures of risk, Annals of Operations Research , DOI:10.1007/s10479-015-1801-0. [3] Chernikov...Operations Research , 50(3):415–423, 2002. [16] I. Ljubi, P. Mutzel, and B. Zey. Stochastic survivable network design problems. Electronic Notes in Discrete

Solid State Research, 1980:1.

DTIC Science & Technology

1980-02-15

ESD-TR-79-325 H 1 Solid State Research 1980 Prepared under Electronic Systems Division Contract FI%28-80-C-0002 by Lincoln Laboratory MASSkCHIISETTS...it is no longer needed. MASSACHUSETTS IN*STITUTE OF TECHNOLOGY LINCOLN LABORATORY V SOLID STATE RESEARCH QUARTERLY TECHNICAL SUMMARY REPORT I NOVEMBER...January 1990. The topics covered a-e Solid State Device Research , Quantum Electronics, Materials Rese.rch, Microelec- tronics, and Analog Device

Strategic Studies Quarterly. Volume 9, Number 2. Summer 2015

DTIC Science & Technology

2015-01-01

disrupting financial markets. Among other indicators, China’s already deployed and future Type 094 Jin -ciass nuclear ballistic missile submarines (SSBN...on agility instead of brute force re- inforces traditional Chinese military thinking. Since Sun Tzu, the acme of skill has been winning without... mechanical (both political and technical) nature of digital developments. Given this, the nature of system constraints under a dif- ferent future

Impact of performance-based financing on primary health care services in Haiti.

PubMed

Zeng, Wu; Cros, Marion; Wright, Katherine D; Shepard, Donald S

2013-09-01

To strengthen Haiti's primary health care (PHC) system, the country first piloted performance-based financing (PBF) in 1999 and subsequently expanded the approach to most internationally funded non-government organizations. PBF complements support (training and technical assistance). This study evaluates (a) the separate impact of PBF and international support on PHC's service delivery; (b) the combined impact of PBF and technical assistance on PHC's service delivery; and (c) the costs of PBF implementation in Haiti. To minimize the risk of facilities neglecting potential non-incentivized services, the incentivized indicators were randomly chosen at the end of each year. We obtained quantities of key services from four departments for 217 health centres (15 with PBF and 202 without) from 2008 through 2010, computed quarterly growth rates and analysed the results using a difference-in-differences approach by comparing the growth of incentivized and non-incentivized services between PBF and non-PBF facilities. To interpret the statistical analyses, we also interviewed staff in four facilities. Whereas international support added 39% to base costs of PHC, incentive payments added only 6%. Support alone increased the quantities of PHC services over 3 years by 35% (2.7%/quarter). However, support plus incentives increased these amounts by 87% over 3 years (5.7%/quarter) compared with facilities with neither input. Incentives alone was associated with a net 39% increase over this period, and more than doubled the growth of services (P < 0.05). Interview findings found no adverse impacts and, in fact, indicated beneficial impacts on quality. Incentives proved to be a relatively inexpensive, well accepted and very effective complement to support, suggesting that a small amount of money, strategically used, can substantially improve PHC. Haiti's experience, after more than a decade of use, indicates that incentives are an effective tool to strengthen PHC.

Role of National Immunization Technical Advisory Group on improvement of immunization programmes in the Islamic Republic of Iran.

PubMed

Zahraei, Seyed Mohsen; Marandi, Alireza; Sadrizadeh, Bijan; Gouya, Mehdi Mohammad; Rezaei, Parviz; Vazirian, Parviz; Yaghini, Fatheme

2010-04-19

The National Immunization Technical Advisory Group (NITAG) was established in Iran in 1982 and has made many important technical recommendations (e.g., regarding polio eradication, introduction of new vaccines, organizing special studies) that have contributed to a dramatic decline in vaccine preventable disease burden. The NITAG consists of experts from the Ministry of Health and Medical Education (MOHME), vaccine manufacturers, and medical universities with national Expanded Program of Immunization (EPI) staff serving as the secretariat. It is not completely independent from MOHME or EPI. It meets on a quarterly basis, and publishes national guidelines and immunization schedules that are updated regularly. Although primarily an advisory body, representation from MOHME members, including the EPI manager, ensures almost universal implementation of NITAG recommendations. Copyright © 2010 Elsevier Ltd. All rights reserved.

Ultraviolet spectrometer and polarimeter (UVSP) software development and hardware tests for the solar maximum mission

NASA Technical Reports Server (NTRS)

Bruner, M. E.; Haisch, B. M.

1986-01-01

The Ultraviolet Spectrometer/Polarimeter Instrument (UVSP) for the Solar Maximum Mission (SMM) was based on the re-use of the engineering model of the high resolution ultraviolet spectrometer developed for the OSO-8 mission. Lockheed assumed four distinct responsibilities in the UVSP program: technical evaluation of the OSO-8 engineering model; technical consulting on the electronic, optical, and mechanical modifications to the OSO-8 engineering model hardware; design and development of the UVSP software system; and scientific participation in the operations and analysis phase of the mission. Lockheed also provided technical consulting and assistance with instrument hardware performance anomalies encountered during the post launch operation of the SMM observatory. An index to the quarterly reports delivered under the contract are contained, and serves as a useful capsule history of the program activity.

PMJ 2007 panel discussion overview: double exposure and double patterning for 32-nm half-pitch design node

NASA Astrophysics Data System (ADS)

Nagaoka, Yoshinori; Watanabe, Hidehiro

2007-10-01

As part of the technical program in Photomask Japan 2007, we held a panel discussion to discuss challenges and solutions for the double exposure and double patterning lithography technique for 32nm half-pitch design node. 4 panelists, Rik Jonckheere of IMEC, Belgium), Tsann-Binn Chiou of ASML Taiwan Ltd., Taiwan), Judy Huckabay of Cadence Design Systems Inc. (USA) and Yoshimitsu Okuda of Toppan Printing Co., Ltd., Japan) were invited to represent each key technical area. We also took a survey from the PMJ attendees prior to the panel discussion, to vote which key technical area they think the challenge exists for the 32nm half-pitch DE/DP lithography. The result of the survey was also presented during the panel discussion. One would intuitively think that by using a DE/DP technique you're relaxing the design rule by 2x, thus for 32nm node it's essentially the 65nm process- you're just repeating it 2 times. Well, not exactly, as identified by the panelists and the participants in the discussion. We recognized the difficulties in the LSI fabrication process steps, the lithography tool overlay, photomask CD and registration, and the issue of data splitting conflict. These difficulties are big challenge for both LSI and photomask manufactures; however, we have confirmed some solutions are already examined by the theoretical and experimental works of the people in research. Despite these difficulties, we are convinced that the immersion lithography with double exposure and double patterning techniques is one of the most promising candidates of the lithography for 32nm half pitch design node.

Field Demonstration of Light Obscuration Particle Counting Technologies to Detect Fuel Contaminates

DTIC Science & Technology

2016-12-01

to detect fuel contamiation including particulates and free water 15. SUBJECT TERMS fuel, JP-8, aviation fuel, contamination, free water ...undissolved water , F24 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT none 18. NUMBER OF PAGES 12 19a. NAME OF RESPONSIBLE PERSON Joel...technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED. Indicate the time during

The New Guard: A Service-Equivalent Force

DTIC Science & Technology

2012-06-07

quartermas ter , medical , ordinance and inspector general. The bureaus were designed to be more efficient and deliver cost aving; but. onl y created...2. REPORT TYPE. State the type of report, such as final , technical, interim, memorandum, master’s thesis , progress, quarterly, research ...the report, performing the research , or credited with the content of the report. The form of entry is the last name, first name, middle initial, and

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2004-01-01

The titles of five reports are listed here, together with an abstract for each. The titles include: 1) 'Spectral Models of Kuiper Belt Objects and Centaurs'; 2) 'Simulation of and for Military Decision Making'; 3) 'Abundance of the Radioactive Be-10 in the Cosmic Radiation up to 2 GeV/nucleon with the Balloon-borne Instrument ISOMAX1998'; 4) 'Optical Air Flow Measurements in Flight'; 5) 'Flight Test Measurement Techniques for Laminar Flow'.

Reassuring Russia On BMD

DTIC Science & Technology

2016-02-16

contrary, other officials, such as Russia’s Ambassador to the United Nations, Vitaly Churkin, were unimpressed, stating that the United States BMD...Joint Threat Assessment by U.S. and Russian Technical Experts, May 2009, 3. 20 George N . Lewis and Theodore A. Postol, “A Flawed and Dangerous U.S...Kramer, David J. “Resetting US-Russian Relations: It Takes Two.” The Washington Quarterly 33, no. 1 (2010). Lewis, George N ., and Theodore A

Publications of the Jet Propulsion Laboratory, 1988

NASA Technical Reports Server (NTRS)

1989-01-01

This bibliography describes and indexes by primary author the externally distributed technical reporting, released during calendar year 1988, that resulted from scientific and engineering work performed, or managed, by the Jet Propulsion Laboratory. Three classes of publications are included: JPL publications in which the information is complete for a specific accomplishment; articles from the quarterly Telecommunications and Data Acquisition (TDA) Progress Report; and articles published in the open literature.

Trust in Teams Scale, Trust in Leaders Scale: Manual for Administration and Analyses

DTIC Science & Technology

2008-07-01

Committee The scientific or technical validity of this Contractor Report is entirely the responsibility of the contractor and the...and Farley’s exploratory analysis of the unit climate profile. DRDC Toronto Report CR-2001-149. KORSGAARD, M . A., S. E. BRODT, & WHITENER, E. M ...8217 trust in leader, satisfaction, and organizational citizenship behaviors. Leadership Quarterly, 1(2), 107-142. ROUSSEAU , D ., SITKIN, S., BURT, R

Gender and Racial Equity in the U.S. Military Occupational Distribution

DTIC Science & Technology

1988-09-30

suggested here could be operating. Discussion of those cited follows. Structural Discrimination The terms racism , sexism , institutional racism , and struct...a statistically significant level. Specifically, they were consistently underrepresented in the core technical occupations while White males...with Black enlisted men who number 198,000, or 30% of enlisted Army men, and 396,000, or 22% of enlisted men in the DoD Services (Quarterly Statistics

Acquisition Review Quarterly (ARQ), Volume 1 Number 3, Summer 1994

DTIC Science & Technology

1994-01-01

sole- and dual-source production and their cost implications , and suggests the use of explicit demand curves. 281 - GUIDELINES FOR AUTHORS...millions of square miles of the American landscape. If you look at a map, it is astonishing how much of the country we cover. Naturally, nearly every- thing...See Carnegie Commission Report, Facing Towards Governments - Nongovernmental Organi- zations and Scientific and Technical Advice (New York: Carnegie

Research and Theory on the Motivation to Lead: Implications for Officer Selection

DTIC Science & Technology

2000-08-01

Psychological Review, 98, 224-253. Vroom , V . H ., & Yetton, P. W. (1973). Leadership Meyer, J. P. & Allen, N. J. (1991). A three- and decision-making...behavior. In M. M. Page (Ed.), Nebraska Leadership Quarterly, 3, 137-157. Symposium on Motivation , beliefs, attitudes and values Markus, H ...UNCLASSIFIED Defense Technical Information Center Compilation Part Notice ADP010357 TITLE: Research and Theory on the Motivation to Lead

Cellular Mechanisms of Transcranial Direct Current Stimulation

DTIC Science & Technology

2016-07-14

REPORT TYPE. State the type of report, such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group ...in fEPSP timing was not resolved. Importantly, grouping across all pathways (e.g. not controlling pathway selectivity), 8 V/m radial positive fields...each signal group during DCS and in control conditions (no electrical stimulation). F) Changes in synaptic strength for each signal group under all

Quarterly Performance/Technical Report of the National Marrow Donor Program

DTIC Science & Technology

2010-03-31

Implemented the Business to Business ( B2B ) Gateway and Business Services to support : • Incoming HLA typing results incorporating HLA Nomenclature changes...maintenance was performed. IIA.3.2 Task 2: Critical Facility and Staff Related Functions Period 6 Activity: • Business Continuity Planning: o Continued...department development of appropriate detailed tasks to be tested at a remote (non-NMDP controlled) location for the 2010 Business Continuity

Publications of the Jet Propulsion Laboratory, 1985

NASA Technical Reports Server (NTRS)

1986-01-01

This bibliography describes and indexes by primary author the externally distributed technical reporting, released during calender year 1985, that resulted from scientific and engineering work performed, or managed, by the Jet Propulsion Laboratory. Three classes of publications are included: JPL publications in which the information is complete for a specific accomplisment; Articles from the quarterly Telecommunications and Data Acquisition (TDA) Progress Report; and article published in the open literature.

Behind the Scenes, Animal Caretakers and Technical Staff Contribute to High-Quality Research | Poster

Cancer.gov

By Frank Blanchard, Staff Writer; photos by Frank Blanchard and Richard Frederickson, Staff Photographer Each day at 6 a.m. the lights pop on inside 18 buildings on the NCI at Frederick campus, illuminating the residential quarters for thousands of research mice. For the mice, it’s the end of their nocturnal day.  For their caretakers, however, the day has just begun.

Catalyst and process development for the H/sub 2/ preparation from future fuel cell feedstocks. Quarterly progress report, October 1, 1978-December 31, 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yarrington, R M; Feins, I R; Hwang, H S

1979-01-01

The work done under this contract in the last quarter of 1978 was concerned with Phase I, which involved preliminary catalyst and process evaluation. The processes under study are hydrogen assisted steam reforming (HASR), catalytic partial oxidation (CPO), and autothermal steam reforming (ATR). Existing Engelhard test units were modified to carry out preliminary runs using the first two processes. Technical analysis to support work in this area consisted of heat and material balances constrained by equilibrium considerations. In a third task, the steam reforming of methanol to produce hydrogen was studied over two commercial low-temperature shift catalysts. Aging runs indicatedmore » good initial performance on both catalysts, but methanol conversion started to decline after a few hundred hours on stream.« less

Hydroacoustic Studies Using HydroCAM - Station-centric Integration of Models and Observations Quarterly Report No.4 July 2003 - September 2003

DOE Office of Scientific and Technical Information (OSTI.GOV)

Upton, Zachary, M.; Pulli, Jay, J.

2003-10-13

OAK B272 Quarterly technical report summarizing BBN's efforts to improve DOE's hydroacoustic modeling and analysis capability for nuclear explosion monitoring. BBN's work during the third quarter of 2003 was focused on preparations for and participation in the 2003 Seismic Research Review Meeting, unit testing and bug fixes to HydroCAM 4.1, data collection and analysis, and procuring high-resolution bathymetric data. In an attempt to save money, BBN scaled back its labor in the third quarter, delaying some deliverables but saving contract funding in case our next increment is delayed. We have succeeded in finding the correct Naval contact that can helpmore » us procure high-resolution bathymetry data. Although these data may require the release of a classified version of HydroCAM, we are optimistic that we will be able to acquire and integrate high-resolution bathymetric data near the Indian Ocean IMS stations. HydroCAM 4.1, which includes the ability to make blockage predictions using varying resolution bathymetric data, has completed unit testing and is now under integration (release) testing. We hope to deliver that functionality to DOE and AFTAC in November. BBN improved its database of hydroacoustic events in the Indian Ocean by including meta-data for associated arrivals. For each earthquake event, BBN is now picking the direct arrival at each station (Diego Garcia North and South, and Cape Leeuwin) and associating that arrival with the origin information that we are compiling. The data for 2001, 2002 and 2003 (to date) will be delivered to LLNL for integration into the Knowledge Base during the fourth quarter of 2003.« less

Routine Leak Testing in Colorectal Surgery in the Surgical Care and Outcomes Assessment Program

PubMed Central

Kwon, Steve; Morris, Arden; Billingham, Richard; Frankhouse, Joseph; Horvath, Karen; Johnson, Morrie; McNevin, Shane; Simons, Anthony; Symons, Rebecca; Steele, Scott; Thirlby, Richard; Whiteford, Mark; Flum, David R.

2014-01-01

Objective To evaluate the effect of routine anastomotic leak testing (performed to screen for leaks) vs selective testing (performed to evaluate for a suspected leak in a higher-risk or technically difficult anastomosis) on outcomes in colorectal surgery because the value of provocative testing of colorectal anastomoses as a quality improvement metric has yet to be determined. Design Observational, prospectively designed cohort study. Setting Data from Washington state’s Surgical Care and Outcomes Assessment Program (SCOAP). Patients Patients undergoing elective left-sided colon or rectal resections at 40 SCOAP hospitals from October 1, 2005, to December 31, 2009. Interventions Use of leak testing, distinguishing procedures that were performed at hospitals where leak testing was selective (<90% use) or routine (≥90% use) in a given calendar quarter. Main Outcome Measure Adjusted odds ratio of a composite adverse event (CAE) (unplanned postoperative intervention and/or in-hospital death) at routine testing hospitals. Results Among 3449 patients (mean [SD] age, 58.8[14.8] years; 55.0% women), the CAE rate was 5.5%. Provocative leak testing increased (from 56% in the starting quarter to 76% in quarter 16) and overall rates of CAE decreased (from 7.0% in the starting quarter to 4.6% in quarter 16; both P ≤ .01) over time. Among patients at hospitals that performed routine leak testing, we found a reduction of more than 75% in the adjusted risk of CAEs (odds ratio, 0.23; 95% CI, 0.05–0.99). Conclusion Routine leak testing of left-sided colorectal anastomoses appears to be associated with a reduced rate of CAEs within the SCOAP network and meets many of the criteria of a worthwhile quality improvement metric. PMID:22508778

Routine leak testing in colorectal surgery in the Surgical Care and Outcomes Assessment Program.

PubMed

Kwon, Steve; Morris, Arden; Billingham, Richard; Frankhouse, Joseph; Horvath, Karen; Johnson, Morrie; McNevin, Shane; Simons, Anthony; Symons, Rebecca; Steele, Scott; Thirlby, Richard; Whiteford, Mark; Flum, David R

2012-04-01

To evaluate the effect of routine anastomotic leak testing (performed to screen for leaks) vs selective testing (performed to evaluate for a suspected leak in a higher-risk or technically difficult anastomosis) on outcomes in colorectal surgery because the value of provocative testing of colorectal anastomoses as a quality improvement metric has yet to be determined. Observational, prospectively designed cohort study. Data from Washington state's Surgical Care and Outcomes Assessment Program (SCOAP). Patients undergoing elective left-sided colon or rectal resections at 40 SCOAP hospitals from October 1, 2005, to December 31, 2009. Use of leak testing, distinguishing procedures that were performed at hospitals where leak testing was selective (<90% use) or routine (≥ 90% use) in a given calendar quarter. Adjusted odds ratio of a composite adverse event (CAE) (unplanned postoperative intervention and/or in-hospital death) at routine testing hospitals. Among 3449 patients (mean [SD] age, 58.8 [14.8] years; 55.0% women), the CAE rate was 5.5%. Provocative leak testing increased (from 56% in the starting quarter to 76% in quarter 16) and overall rates of CAE decreased (from 7.0% in the starting quarter to 4.6% in quarter 16; both P ≤ .01) over time. Among patients at hospitals that performed routine leak testing, we found a reduction of more than 75% in the adjusted risk of CAEs (odds ratio, 0.23; 95% CI, 0.05-0.99). Routine leak testing of left-sided colorectal anastomoses appears to be associated with a reduced rate of CAEs within the SCOAP network and meets many of the criteria of a worthwhile quality improvement metric.

Scientific and Technical Development of the Next Generation Space Telescope

NASA Technical Reports Server (NTRS)

Burg, Richard

2003-01-01

The Next Generation Space Telescope (NGST) is part of the Origins program and is the key mission to discover the origins of galaxies in the Universe. It is essential that scientific requirements be translated into technical specifications at the beginning of the program and that there is technical participation by astronomers in the design and modeling of the observatory. During the active time period of this grant, the PI participated in the NGST program at GSFC by participating in the development of the Design Reference Mission, the development of the full end-to-end model of the observatory, the design trade-off based on the modeling, the Science Instrument Module definition and modeling, the study of proto-mission and test-bed development, and by participating in meetings including quarterly reviews and support of the NGST SWG. This work was documented in a series of NGST Monographs that are available on the NGST web site.

Site Operator technical report. Final report (1992--1996)

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1996-12-01

The Southern California Edison Company (SCE) and the US Department of Energy (DOE) entered into cooperative agreement No. DE-FC07-91ID13077 on August 23, 1991, which expired on August 3, 1996. This cooperative agreement provided SCE with DOE cofunding for participation in the DOE`s Electric and Hybrid Vehicle Site Operator Program. In return, SCE provided the DOE with quarterly progress reports which include operating and maintenance data for the electric (EVs) vehicles in SCE`s fleet. Herein is SCE`s final report for the 1992 to 1996 agreement period. As of September 1, 1996 the SCE fleet had 65 electric vehicles in service. Amore » total of 578,200 miles had been logged. During the agreement period, SCE sent the DOE a total of 19 technical reports (Appendix B). This report summarizes the technical achievements which took place during a long, productive and rewarding, relationship with the DOE.« less

Influence of substrate temperatures on the properties of GdF(3) thin films with quarter-wave thickness in the ultraviolet region.

PubMed

Jin, Jingcheng; Jin, Chunshui; Li, Chun; Deng, Wenyuan; Yao, Shun

2015-06-01

High-quality coatings of fluoride materials are in extraordinary demand for use in deep ultraviolet (DUV) lithography. Gadolinium fluoride (GdF₃) thin films were prepared by a thermal boat evaporation process at different substrate temperatures. GdF₃ thin film was set at quarter-wave thickness (∼27  nm) with regard to their common use in DUV/vacuum ultraviolet optical stacks; these thin films may significantly differ in nanostructural properties at corresponding depositing temperatures, which would crucially influence the performance of the multilayers. The measurement and analysis of optical, structural, and mechanical properties of GdF₃ thin films have been performed in a comprehensive characterization cycle. It was found that depositing GdF₃ thin films at relative higher temperature would form a rather dense, smooth, homogeneous structure within this film thickness scale.

Update on POCIT portable optical communicators: VideoBeam and EtherBeam

NASA Astrophysics Data System (ADS)

Mecherle, G. Stephen; Holcomb, Terry L.

2000-05-01

LDSC is developing the POCITTM (Portable Optical Communication Integrated Transceiver) family of products which includes VideoBeamTM and the latest addition, EtherBeamTM. Each is a full duplex portable laser communicator: VideoBeamTM providing near-broadcast- quality analog video and stereo audio, and EtherBeamTM providing standard Ethernet connectivity. Each POCITTM transceiver consists of a 3.5-pound unit with a binocular- type form factor, which can be manually pointed, tripod- mounted or gyro-stabilized. Both units have an operational range of over two miles (clear air) with excellent jam- resistance and low probability of interception characteristics. The transmission wavelength of 1550 nm enables Class 1 eyesafe operation (ANSI, IEC). The POCITTM units are ideally suited for numerous military scenarios, surveillance/espionage, industrial precious mineral exploration, and campus video teleconferencing applications. VideoBeam will be available second quarter 2000, followed by EtherBeam in third quarter 2000.

Installation of Groundwater Monitoring Wells TAV-MW15 and TAV-MW16.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lum, Clinton C. L.

This report documents the installation of two groundwater monitoring wells at the Technical Area V Groundwater (TAVG) Area of Concern at Sandia National Laboratories, New Mexico (SNL/NM). SNL/NM is managed and operated by National Technology and Engineering Solutions of Sandia, LLC., a wholly owned subsidiary of Honeywell International Inc., for the U.S. Department of Energy’s National Nuclear Security Administration under contract DE-NA- 0003525. Well installation activities were conducted in accordance with the New Mexico Environment Department (NMED) Hazardous Waste Bureau (HWB)-approved work plan Revised Treatability Study Work Plan for In-Situ Bioremediation at the Technical Area-V Groundwater Area of Concern (Workmore » Plan) (SNL/NM March 2016). The Work Plan was approved by NMED HWB prior to the start of field work (NMED May 2016). Project activities were performed from November 2016 through January 2017 by SNL/NM Environmental Restoration (ER) Operations personnel, and the SNL/NM drilling contractor Cascade Drilling LP. Drilling activities began with borehole drilling and sampling on November 30, 2016. Well construction and development fieldwork was completed on January 31, 2017. Land surveys to establish the location coordinates and elevations of the two wells were completed on March 23, 2017, and transmitted to SNL/NM personnel on April 17, 2017.« less

589 nm sum-frequency generation laser for the LGS/AO of Subaru Telescope

NASA Astrophysics Data System (ADS)

Saito, Yoshihiko; Hayano, Yutaka; Saito, Norihito; Akagawa, Kazuyuki; Takazawa, Akira; Kato, Mayumi; Ito, Meguru; Colley, Stephen; Dinkins, Matthew; Eldred, Michael; Golota, Taras; Guyon, Olivier; Hattori, Masayuki; Oya, Shin; Watanabe, Makoto; Takami, Hideki; Iye, Masanori; Wada, Satoshi

2006-06-01

We developed a high power and high beam quality 589 nm coherent light source by sum-frequency generation in order to utilize it as a laser guide star at the Subaru telescope. The sum-frequency generation is a nonlinear frequency conversion in which two mode-locked Nd:YAG lasers oscillating at 1064 and 1319 nm mix in a nonlinear crystal to generate a wave at the sum frequency. We achieved the qualities required for the laser guide star. The power of laser is reached to 4.5 W mixing 15.65 W at 1064 nm and 4.99 W at 1319 nm when the wavelength is adjusted to 589.159 nm. The wavelength is controllable in accuracy of 0.1 pm from 589.060 and 589.170 nm. The stability of the power holds within 1.3% during seven hours operation. The transverse mode of the beam is the TEM 00 and M2 of the beam is smaller than 1.2. We achieved these qualities by the following technical sources; (1) simple construction of the oscillator for high beam quality, (2) synchronization of mode-locked pulses at 1064 and 1319 nm by the control of phase difference between two radio frequencies fed to acousto-optic mode lockers, (3) precise tunability of wavelength and spectral band width, and (4) proper selection of nonlinear optical crystal. We report in this paper how we built up each technical source and how we combined those.

Individual dose monitoring of the nuclear medicine departments staff controlled by Central Laboratory for Radiological Protection.

PubMed

Szewczak, Kamil; Jednoróg, Sławomir; Krajewski, Paweł

2013-01-01

Presented paper describes the results of the individual doses measurements for ionizing radiation, carried out by the Laboratory of Individual and Environmental Doses Monitoring (PDIS) of the Central Laboratory for Radiological Protection in Warsaw (CLOR) for the medical staff employees in several nuclear medicine (NM) departments across Poland. In total there are48 NM departments in operation in Poland [1] (consultation in Nuclear Atomic Agency). Presented results were collected over the period from January 2011 to December 2011 at eight NM departments located in Krakow, Warszawa (two departments), Rzeszow (two departments), Opole, Przemysl and Gorzow Wielkopolski. For radiation monitoring three kinds of thermo luminescence dosimeters (TLD) were used. The first TLD h collected information about whole body (C) effective dose, the second dosimeter was mounted in the ring (P) meanwhile the third on the wrist (N) of the tested person. Reading of TLDs was performed in quarterly periods. As a good approximation of effective and equivalent dose assessment of operational quantities both the individual dose equivalent Hp(10) and the Hp(0.07) were used. The analysis of the data was performed using two methods The first method was based on quarterly estimations of Hp(10)q and Hp(0.07)q while the second measured cumulative annual doses Hp(10)a and Hp(0.07)a. The highest recorded value of the radiation dose for quarterly assessments reached 24.4 mSv and was recorded by the wrist type dosimeter worn by a worker involved in source preparation procedure. The mean values of Hp(10)q(C type dosimeter) and Hp(0.07)q (P and N type dosimeter) for all monitored departments were respectively 0.46 mSv and 3.29 mSv. There was a strong correlation between the performed job and the value of the received dose. The highest doses always were absorbed by those staff members who were involved in sources preparation. The highest annual cumulative dose for a particular worker in the considered time period was 4.22 mSv for Hp(10)a and 67.7 mSv for Hp(0.07)a. In 2011 no case of exceeding the allowed dose limits was noted.

ENHANCED PRACTICAL PHOTOSYNTHETIC CO2 MITIGATION

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dr. Gregory Kremer; Dr. David J. Bayless; Dr. Morgan Vis

2001-07-25

This quarterly report documents significant achievements in the Enhanced Practical Photosynthetic CO{sub 2} Mitigation project during the period from 4/03/2001 through 7/02/2001. Most of the achievements are milestones in our efforts to complete the tasks and subtasks that constitute the project objectives. Note that this version of the quarterly technical report is a revision to add the reports from subcontractors Montana State and Oak Ridge National Laboratories The significant accomplishments for this quarter include: Development of an experimental plan and initiation of experiments to create a calibration curve that correlates algal chlorophyll levels with carbon levels (to simplify future experimentalmore » procedures); Completion of debugging of the slug flow reactor system, and development of a plan for testing the pressure drop of the slug flow reactor; Design and development of a new bioreactor screen design which integrates the nutrient delivery drip system and the harvesting system; Development of an experimental setup for testing the new integrated drip system/harvesting system; Completion of model-scale bioreactor tests examining the effects of CO{sub 2} concentration levels and lighting levels on Nostoc 86-3 growth rates; Completion of the construction of a larger model-scale bioreactor to improve and expand testing capabilities and initiation of tests; Substantial progress on construction of a pilot-scale bioreactor; and Preliminary economic analysis of photobioreactor deployment. Plans for next quarter's work are included in the conclusions. A preliminary economic analysis is included as an appendix.« less

Cool pool development. Quarterly technical report No. 2, June-December 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crowther, K.

1980-01-05

The Cool Pool is a variation of the evaporating roof pond idea. The pool is isolated from the living space and the cooled pond water thermosiphons into the water columns located within the building. A computer model of the Cool Pool and the various heat and mass transfer mechanisms involved in the system are discussed. Theory will be compared to experimental data collected from a Cool Pool test building.

76 FR 17413 - Contract Reporting Requirements of Intrastate Natural Gas Companies; Notice of Technical Workshop...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-29

... the PDF or XML version of Form No. 549D as a method to eFile quarterly data and whether they intend on... fillable Form No. 549D PDF and XML to file data \\2\\ pursuant to Order Nos. 735 and 735-A.\\3\\ [[Page 17414... PDF ( http://www.ferc.gov/docs-filing/forms/form-549d/form-549d.pdf ) or XML ( http://www.ferc.gov...

United States Air Force F-35A Operational Basing Environmental Impact Statement. Appendix E: Comments

DTIC Science & Technology

2013-09-01

such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED...appear in the report, e.g. 001; AFAPL30480105. 6. AUTHOR(S). Enter name(s) of person(s) responsible for writing the report, performing the research ...negatively impacted by the noise] SAFTY ALL NEW military aircraft designs suffer crashes during their initial development peri~ Bringing the F-35

Sonar Test and Test Instrumentation Support.

DTIC Science & Technology

1979-03-29

AD-AlSO 055 TEXAS UNIV AT AUSTIN APPLIED RESEARCH LABS F/6 17/1 SONAR TEST AND TEST INSTRUMENTATION SUPPORT (U) MAR 79 0 D BAKER N00140-76-C-64a7... SONAR TEST AND TEST INSTRUMENTATION SUPPORT quarterly progress report September - 30 November 197Pj 6. PERFORMING ORG. REPORT NUMBER 7. AUTHOR(e) S...involves technical support with sonar testing, test instrumentation, and documentation. This report describes progress made under the tasks that are

Publications of the Jet Propulsion Laboratory 1987

NASA Technical Reports Server (NTRS)

1988-01-01

A bibliography is presented which describes and indexes by author the externally distributed technical reporting, released during the calender year 1987, that resulted from scientific and engineering work performed, or managed, by the Jet Propulsion Lab. Three classes of publications are included: (1) JPL publications in which the information is complete for a specific accomplishment; (2) Articles from the quarterly Telecommunications and Data Acquisition Progress Report; and (3) Articles published in the open literature.

Manager Development: A Conceptual Model

DTIC Science & Technology

1976-05-31

Leader Behavior: A Summary. (Technical Report No. 40 on ONR Contract). Rochester, New York, 1972. Vroom , V . H . & E. L. Deci. "The stability of...36-49. Vroom , V . H . & K. R. MacCrimmon "Toward a stochastic model of managerial careers", Administrative Science Quarterly, June, 1968, 26-46. 6...34 ( Vroom and MacCrimmon, 1968). Expanded by White (1970), this approach deems careers not as the result of individual characteristics and motives , but as

Quarterly Performance/Technical Report of the National Marrow Donor Program

DTIC Science & Technology

2010-11-05

care. IIBA. Task 1: Period 8 Activity: Expand Network Co=unications Extended the Business to Business ( B2B ) Services to support the new alleles...exterior glass. • Site visit was conducted at the NMDP operated donor center in Philadelphia (August 12,2010) 0 At these site visits the Business ...Continuity Planner reviews the Business Continuity Action Guide with staff to better prepare each location for responding to incidents that interrupt

Environmental Hazards Assessment Program. Quarterly report, July--September 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

This report describes activities and reports on progress for the first quarter (July--September) of the fourth year of the grant to support the Environmental Hazards Assessment Program (EHAP) at the Medical University of South Carolina. It reports progress against the grant objectives and the Program Implementation Plan published at the end of the first year of the grant. The objectives of EHAP stated in the proposal to DOE are to: (1) develop a holistic, national basis for risk assessment, risk management, and risk communication that recognizes the direct impact of environmental hazards on the health and well-being of all; (2)more » develop a pool of talented scientists and experts in cleanup activities, especially in human health aspects; and (3) identify needs and develop programs addressing the critical shortage of well-educated, highly-skilled technical and scientific personnel to address the health-oriented aspects of environmental restoration and waste management.« less

Research Skills and Ethics--A Graduate Course Empowering Graduate Students for Productive Research Careers in Graduate School and Beyond

NASA Astrophysics Data System (ADS)

Mabrouk, Patricia Ann

2001-12-01

This paper describes a course for first-year graduate students that teaches the fundamental so-called "soft skills" required for success in graduate school and beyond. Topics covered are ethics, laboratory safety and waste management, chemical information retrieval and literacy, experimental design, scientific record keeping, statistics, career development, and communications, including technical writing and oral presentation. Whenever possible students are put in direct contact with local technical experts and available resources. The course, well regarded by both students and faculty, has now been taught at Northeastern University for five years in the summer academic quarter to graduate students in chemistry and related departments (pharmacy and chemical engineering) who have successfully completed their first-year course work.

ANNUAL REPORT, JULY 1, 1958

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1959-02-01

This annual report of Brookhaven National Laboratory describes its program and activities for the fiscal year 1958. The progress and trends of the research program are presented along with a description of the operational, service, and administrative activities of the Laboratory. The scientific and technical details of the many research and development activities are covered more fully in scientific and technical periodicals and in the quarterly scientific progress reports and other scientiflc reports of the Laboratory. A list of all publications for July 1, 1957 to June 30, 1958, is given. Status and progress are given in fields of physics,more » accelerator development, instrumentation, applied mathematics, chemistry, nuclear engineering, biology, and medical research. (For preceding period see BNL-462.) (W.D.M.)« less

75 FR 17911 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-08

...) (June 11, 1997; 62 FR 31793). Reason: The 1550th Technical Training Squadron, Kirtland Air Force Base...: The 1550th Combat Crew Training Wing, Kirtland Air Force Base, NM, no longer exists. Training now..., Kirtland Air Force Base, NM, no longer exists. Training now falls under the Air Education Training Command...

NCEL (Naval Civil Engineering Laboratory) Quarterly Abstracts of Technical Documents, 1 January 1986 to 31 December 1986.

DTIC Science & Technology

1986-12-31

underwater use and evaluated in laboratory and field tests. One of the three instruments was a magnetic rebar locator that locates rebar in concrete ...structures and measures the amount of concrete cover over the rebar . Another instrument was a Schmidt hammer that evaluates the surface hardness of the...Used as Boiler Fuel ..... .................. 3 N-1744 Blistering of Asphalt Pavement Overlay on Runway 14-32 at MCAS Bea, fort, South Carolina

Administrative and Technical Support for the U.S. Army Medical Research and Development Command Joint Working Group on Medical Chemical Defense

DTIC Science & Technology

1989-08-01

microproces;qor databaAing systems for monitoring project and contract reports and program technology trans. fers, coordinating and providing administratIvo ...The JWGD 3 annual planning process generally included: - Program review by the JWGD’ membership at quarterly meetings, which consisted of the review...Office developed the program planning and budget documents associated with the planning process outlined above. Program project databases and

United States Air Force F-35A Operational Basing Environmental Impact Statement. Appendix E: Comments

DTIC Science & Technology

2013-09-01

studies such as this one, and other research conducted in most recent decade. Of course, the housing designation ("not compatible with residential...such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED...appear in the report, e.g. 001; AFAPL30480105. 6. AUTHOR(S). Enter name(s) of person(s) responsible for writing the report, performing the research

Quarterly Performance/Technical Report of the National Marrow Donor Program

DTIC Science & Technology

2006-05-01

HapLogicTM was implemented for all search reports. This provides a real-time DNA - based match that utilizes genotype list data in the up- front match...CCN meeting held at the ASBMT/CIBMTR Tandem conference, the National Library of Medicine (NLM) demonstrated a draft of their web based version of the...making improvements to the web based interface. O Government Signature Date A . Contingency Preparedness (Hypothesis 1) Grant Award N00014-05-1-0859

Photochemical Tissue Bonding for Military Medical Applications Practical Low Cost Low Damage Blood Vessel Repair: Albumin Stent Bonded With 19xx nm Laser

DTIC Science & Technology

2011-02-24

shape. At higher concentrations, the albumin would not flow through the extruder. Quarter 4 We used our temperature-controlled extruder to create...albumin stents with an outside diameter from 2 mm and various inner lumen diameters. Dissolution studies in flowing blood indicated that the stents 3...at the same rate. Determined that gamma sterilization procedure does not affect dissolution. Determined that flow rate affects the dissolution rate

Disentangling Intracycle Interferences in Photoelectron Momentum Distributions Using Orthogonal Two-Color Laser Fields

NASA Astrophysics Data System (ADS)

Xie, Xinhua; Wang, Tian; Yu, ShaoGang; Lai, XuanYang; Roither, Stefan; Kartashov, Daniil; Baltuška, Andrius; Liu, XiaoJun; Staudte, André; Kitzler, Markus

2017-12-01

We use orthogonally polarized two-color (OTC) laser pulses to separate quantum paths in the multiphoton ionization of Ar atoms. Our OTC pulses consist of 400 and 800 nm light at a relative intensity ratio of 10 ∶1 . We find a hitherto unobserved interference in the photoelectron momentum distribution, which exhibits a strong dependence on the relative phase of the OTC pulse. Analysis of model calculations reveals that the interference is caused by quantum pathways from nonadjacent quarter cycles.

Scanning electron microscope measurement of width and shape of 10nm patterned lines using a JMONSEL-modeled library.

PubMed

Villarrubia, J S; Vladár, A E; Ming, B; Kline, R J; Sunday, D F; Chawla, J S; List, S

2015-07-01

The width and shape of 10nm to 12 nm wide lithographically patterned SiO2 lines were measured in the scanning electron microscope by fitting the measured intensity vs. position to a physics-based model in which the lines' widths and shapes are parameters. The approximately 32 nm pitch sample was patterned at Intel using a state-of-the-art pitch quartering process. Their narrow widths and asymmetrical shapes are representative of near-future generation transistor gates. These pose a challenge: the narrowness because electrons landing near one edge may scatter out of the other, so that the intensity profile at each edge becomes width-dependent, and the asymmetry because the shape requires more parameters to describe and measure. Modeling was performed by JMONSEL (Java Monte Carlo Simulation of Secondary Electrons), which produces a predicted yield vs. position for a given sample shape and composition. The simulator produces a library of predicted profiles for varying sample geometry. Shape parameter values are adjusted until interpolation of the library with those values best matches the measured image. Profiles thereby determined agreed with those determined by transmission electron microscopy and critical dimension small-angle x-ray scattering to better than 1 nm. Published by Elsevier B.V.

Results For The Third Quarter Calendar Year 2016 Tank 50H Salt Solution Sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C.

2016-10-13

In this memorandum, the chemical and radionuclide contaminant results from the Third Quarter Calendar Year 2016 (CY16) sample of Tank 50H salt solution are presented in tabulated form. The Third Quarter CY16 Tank 50H samples (a 200 mL sample obtained 6” below the surface (HTF-5-16-63) and a 1 L sample obtained 66” from the tank bottom (HTF-50-16-64)) were obtained on July 14, 2016 and received at Savannah River National Laboratory (SRNL) on the same day. Prior to obtaining the samples from Tank 50H, a single pump was run at least 4.4 hours, and the samples were pulled immediately after pumpmore » shut down. The information from this characterization will be used by Defense Waste Processing Facility (DWPF) & Saltstone Facility Engineering for the transfer of aqueous waste from Tank 50H to the Saltstone Production Facility, where the waste will be treated and disposed of in the Saltstone Disposal Facility. This memorandum compares results, where applicable, to Saltstone Waste Acceptance Criteria (WAC) limits and targets. Data pertaining to the regulatory limits for Resource Conservation and Recovery Act (RCRA) metals will be documented at a later time per the Task Technical and Quality Assurance Plan (TTQAP) for the Tank 50H saltstone task. The chemical and radionuclide contaminant results from the characterization of the Third Quarter CY16 sampling of Tank 50H were requested by Savannah River Remediation (SRR) personnel and details of the testing are presented in the SRNL TTQAP.« less

RTO Technical Publications: A Quarterly Listing

NASA Technical Reports Server (NTRS)

2005-01-01

This is a listing of recent unclassified RTO technical publications processed by the NASA Center for AeroSpace Information covering the period from July 1, 2005 to September 30, 2005; and available in the NASA Aeronautics and Space Database. Contents include: Aeroelastic Deformation: Adaptation of Wind Tunnel Measurement Concepts to Full-Scale Vehicle Flight Testing; Actively Controlling Buffet-Induced Excitations; Modelling and Simulation to Address NATO's New and Existing Military Requirements; Latency in Visionic Systems: Test Methods and Requirements; Personal Hearing Protection including Active Noise Reduction; Virtual Laboratory Enabling Collaborative Research in Applied Vehicle Technologies; A Method to Analyze Tail Buffet Loads of Aircraft; Particle Image Velocimetry Measurements to Evaluate the Effectiveness of Deck-Edge Columnar Vortex Generators on Aircraft Carriers; Introduction to Flight Test Engineering, Volume 14; Pathological Aspects and Associated Biodynamics in Aircraft Accident Investigation;

Alternative sample sizes for verification dose experiments and dose audits

NASA Astrophysics Data System (ADS)

Taylor, W. A.; Hansen, J. M.

1999-01-01

ISO 11137 (1995), "Sterilization of Health Care Products—Requirements for Validation and Routine Control—Radiation Sterilization", provides sampling plans for performing initial verification dose experiments and quarterly dose audits. Alternative sampling plans are presented which provide equivalent protection. These sampling plans can significantly reduce the cost of testing. These alternative sampling plans have been included in a draft ISO Technical Report (type 2). This paper examines the rational behind the proposed alternative sampling plans. The protection provided by the current verification and audit sampling plans is first examined. Then methods for identifying equivalent plans are highlighted. Finally, methods for comparing the cost associated with the different plans are provided. This paper includes additional guidance for selecting between the original and alternative sampling plans not included in the technical report.

Engineering and Physics Optimization of Breed and Burn Fast Reactor Systems; NUCLEAR ENERGY RESEARCH INITIATIVE (NERI) QUARTERLY PROGRESS REPORT

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pavel Hejzlar, Peter Yarsky, Mike Driscoll, Dan Wachs, Kevan Weaver, Ken Czerwinski, Mike Pope, James Parry, Theron D. Marshall, Cliff B. Davis, Dustin Crawford, Thomas Hartmann, Pradip Saha; Hejzlar, Pavel; Yarsky, Peter

2005-01-31

This project is organized under four major tasks (each of which has two or more subtasks) with contributions among the three collaborating organizations (MIT, INEEL and ANL-West): Task A: Core Physics and Fuel Cycle; Task B: Core Thermal Hydraulics; Task C: Plant Design; Task D: Fuel Design The lead PI, Michael J. Driscoll, has consolidated and summarized the technical progress submissions provided by the contributing investigators from all sites, under the above principal task headings.

Publications of the Jet Propulsion Laboratory, 1984

NASA Technical Reports Server (NTRS)

1985-01-01

The Jet Propulsion Laboratory (JPL) bibliography 39-26 describes and indexes by primary author the externally distributed technical reporting, released during calendar year 1984, that resulted from scientific and engineering work performed, or managed, by the Jet Propulsion Laboratory. Three classes of publications are included: (1) JPL Publications (82-, 83-, 84-series, etc.), in which the information is complete for a specific accomplishment; (2) articles from the quarterly Telecommunications and Data Acquisition (TDA) Program Report (42-series); and (3) articles published in the open literature.

Summaries of Papers Presented at Photonic Switching Topical Meeting Held in Salt Lake City, Utah on 1-3 March 1989. Technical Digest

DTIC Science & Technology

1990-01-31

a set of codes which will provide a large number of addresses while minimizing interference . We have analyzed the bit error rate (BER) of the...there will be significant crosstalk. The most severe interference will be caused by the unswitched component of the high-intensity pulses. For example...Diagram of Experimental Apparatus Q = Quarter-wave Plate P = Polarising Filter IF = Interference Filter Figure 2. I Oscilloscope trace a. of Kerr

United States Air Force F-35A Operational Basing Environmental Impact Statement. Appendix E: Comments

DTIC Science & Technology

2013-09-01

hreatens the well being of our community, whether through noi se and emissions or the risk of accidents from an under- test ed and flawed design . The...such as final, technical, interim, memorandum, master’s thesis, progress, quarterly, research , special, group study, etc. 3. DATES COVERED...appear in the report, e.g. 001; AFAPL30480105. 6. AUTHOR(S). Enter name(s) of person(s) responsible for writing the report, performing the research

The Fruits of Adversity: Technical Refinements of the Turkish Composite Bow during the Crusading Era

DTIC Science & Technology

1991-01-01

armoured than any other contemporary foe faced by Muslim armies in the Middle East. Archeological evidence shows that an evolution took place from the...driven by the extended exposure of the Muslim warrior to the heavily armoured Western-soldier who employed the powerful crossbow as their primary missile...Fakhr-i Mudabbir’s Adab al Harb (Early Thirteenth Century)’, The Islamic Quarterly XVIIi (1974), pp. 76-99. Nicolle, David C., Arms and Armour of the

Efficient Safety and Degradation Modeling of Automotive Lithium-ion Cells and Packs

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Chao-Yang

2017-09-07

This document is intended to give an overall synopsis of the activities and accomplishments of the EC Power CAEBAT2 project over the course of four years. The reader is referred to the previously submitted quarterly reports, review presentations, and AMR presentations for further technical details. As highlighted by the numerous results shown herein and the volume and quality of the publications and presentations made in the course of this project, we feel that we have made a strong impact in the community.

Contracts for field projects and supporting research on enhanced oil recovery. Progress review number 83, quarter ending June 30, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

Summaries of 41 research projects on enhanced recovery are presented under the following sections: (1) chemical flooding; (2) gas displacement; (3) thermal recovery; (4) geoscience technology; (5) resource assessment technology; and (6) reservoir classes. Each presentation gives the title of the project, contract number, research facility, contract date, expected completion data, amount of the award, principal investigator, and DOE program manager, and describes the objectives of the project and a summary of the technical progress.

Reliability Information Analysis Center 1st Quarter 2007, Technical Area Task (TAT) Report

DTIC Science & Technology

2007-02-05

34* Created new SQL server database for "PC Configuration" web application. Added roles for security closed 4235 and posted application to production. "e Wrote...and ran SQL Server scripts to migrate production databases to new server . "e Created backup jobs for new SQL Server databases. "* Continued...second phase of the TENA demo. Extensive tasking was established and assigned. A TENA interface to EW Server was reaffirmed after some uncertainty about

Publications of the Jet Propulsion Laboratory: 1990 and 1991

NASA Technical Reports Server (NTRS)

1993-01-01

JPL Bibliography 39-32 describes and indexes by primary author the externally distributed technical reporting, released during calendar years 1990 and 1991, that resulted from scientific and engineering work performed or managed by the Jet Propulsion Laboratory (JPL). Three classes of publications are included: (1) JPL publications (90- and 91-series) in which the information is complete for a specific accomplishment; (2) articles from the quarterly Telecommunications and Data Acquisition (TDA) Progress Report (42-series); and (3) articles published in the open literature.

Quarterly Technical Progress Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mary K. Banken

This project has identified all FDD oil reservoirs in Oklahoma; grouped those reservoirs into plays that have similar depositional origins; collected, organized, and analyzed all available data; conducted characterization and simulation studies on selected reservoirs in each plays; and implemented a technology transfer program targeted to the operators of FDD reservoirs. By fulfilling these objectives, the FDD project has had the goal of helping to sustain the life expectancy of existing wells and provide incentive for development and exploratory wells with the ultimate objective of increasing oil recovery.

Quarterly technical progress report, April-June 1982

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1984-04-01

Progress reports are presented for the following tasks: (1) preparation of low-rank coals; application of liquefaction processes to low-rank coals; (2) slagging fixed-bed gasification; (3) atmospheric fluidized-bed combustion of low-rank coal; (4) ash fouling and combustion modification for low-rank coal; (5) combined flue gas cleanup/simultaneous SO/sub x/-NO/sub x/ control; (6) particulate control and hydrocarbons and trace element emissions from low-rank coals; (7) waste characterization and disposal; and (9) exploratory research.

A Guidance Document for Kentucky's Oil and Gas Operations

DOE Office of Scientific and Technical Information (OSTI.GOV)

None, None

1998-11-10

This technical report is a summary of the progress made for "A Guidance Document for Kentucky's Oil and Gas Operators". During this quarter, the document received continued review and editing in an elec-tronic format to satisfy the United States Department of Energy (DOE). Comments received from oil and gas operators reviewing this document prompted contact to be made with the United States Environmental Protection Agency (USEPA) to develop an addendum section to provide better explanation of USEPA requirements for Class II injection wells in Kentucky.

Line focus concentrating collector for Copper Mountain Ski Resort, Colorado (Engineering Materials)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1983-06-02

The present invention is a device which develops an accurate line focus concentrating collector by flexural bending of thin reflective materials. This method avoids the need for expensive tooling and support frame fabrication. The technical work conducted during this quarter included completion of designs for the prototype system for the Copper Mountain Ski Resort in Colorado. Evaluation of alternate tracking and drive systems and final design of the support system. These drawings accompany DOE/CS/15072--T4.

Quarterly Performance/Technical Report of the National Marrow Donor Program

DTIC Science & Technology

2009-02-10

and epitope level matching for HLA-DPB1. Submitted. o Z Shamim , L Ryder, M Haagenson , S Spellman, T Wang, S Lee, K Müller. Polymorphism in the...3, 4 6. AUTHOR( S ) Setterholm, Michelle 5f. WORK UNIT NUMBER N/A 7. PERFORMING ORGANIZATION NAME( S ) AND ADDRESS(ES) National Marrow Donor...Program 3001 Broadway St., N.E., Ste. 500 Minneapolis, MN 55413 8. PERFORMING ORGANIZATION REPORT NUMBER N/A 10. SPONSOR/MONITOR’S ACRONYM( S ) ONR 9

Characteristics of American coals in relation to their conversion into clean energy fuels. Quarterly technical progress report, July-September 1978

DOE Office of Scientific and Technical Information (OSTI.GOV)

Spackman, W.; Davis, A.; Walker, P. L.

1979-05-01

Certain important aspects of the chemical and physical composition of American lignite coals are being characterized. Differential scanning calorimetry and thermogravimetric analysis were used to study the interaction between oxygen and seventeen coal chars (40 x 100 mesh) at 100/sup 0/C. The same techniques were used to investigate briefly the interaction between air and a highly caking coal at selected isothermal temperatures in the range 100 to 275/sup 0/C.

Poinsettia latent virus is not a cryptic virus, but a natural polerovirus-sobemovirus hybrid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siepen, Marc aus dem; Pohl, Jens O.; Koo, Bong-Jin

2005-06-05

The biochemical and genetic features of Poinsettia latent virus (PnLV, formerly named Poinsettia cryptic virus), which is spread worldwide in commercial cultivars of Euphorbia pulcherrima without inducing symptoms, have been determined using virus-purification, immunological techniques, electron microscopy, cloning, and sequencing. PnLV was found to be a chimeric virus with one 4652 bases, plus strand RNA showing a close relationship to poleroviruses within the first three quarters of its genome but to sobemoviruses in the last quarter. Thus, we propose to classify this virus as 'polemovirus'. Similarities of protein and nucleic acid sequences at the 5' and extreme 3' end ofmore » its RNA suggest a replication mode like that of poleroviruses, whereas the coat protein sequence is closely related to that of sobemoviruses. Consistent with these results, PnLV forms stable icosahedra of 34 nm in diameter. The consequences for the taxonomy of PnLV and for gardeners' practice are discussed.« less

AFWL Standards for Scientific and Technical Reports.

DTIC Science & Technology

1980-04-01

Air Force Weapons Laboratory , Kirtland Air Force Base, New Mexico, under...PROGRAM ELEMEN T PROJECT TASK AREA & WORK UNIT NUMBERS Air Force Weapons Laboratory (SUR) Kirtland Air Force Base, NM 87117 62601F/99930000 I. CONTROLLING...OFFICE NAME AND ADDRESS 12 REPORT DATE Air Force Weapons Laboratory (SUR) April 1980 Kirtland Air Force Base, NM 87117 13. NUMBER OF PAGES 72

A Dense Poly(ethylene glycol) Coating Improves Penetration of Large Polymeric Nanoparticles within Brain Tissue

PubMed Central

Nance, Elizabeth A.; Woodworth, Graeme F.; Sailor, Kurt A.; Shih, Ting-Yu; Xu, Qingguo; Swaminathan, Ganesh; Xiang, Dennis; Eberhart, Charles; Hanes, Justin

2013-01-01

Prevailing opinion suggests that only substances up to 64 nm in diameter can move at appreciable rates through the brain extracellular space (ECS). This size range is large enough to allow diffusion of signaling molecules, nutrients, and metabolic waste products, but too small to allow efficient penetration of most particulate drug delivery systems and viruses carrying therapeutic genes, thereby limiting effectiveness of many potential therapies. We analyzed the movements of nanoparticles of various diameters and surface coatings within fresh human and rat brain tissue ex vivo and mouse brain in vivo. Nanoparticles as large as 114-nm in diameter diffused within the human and rat brain, but only if they were densely coated with poly(ethylene glycol) (PEG). Using these minimally adhesive PEG-coated particles, we estimated that human brain tissue ECS has some pores larger than 200 nm, and that more than one-quarter of all pores are ≥100 nm. These findings were confirmed in vivo in mice, where 40- and 100-nm, but not 200-nm, nanoparticles, spread rapidly within brain tissue, only if densely coated with PEG. Similar results were observed in rat brain tissue with paclitaxel-loaded biodegradable nanoparticles of similar size (85 nm) and surface properties. The ability to achieve brain penetration with larger nanoparticles is expected to allow more uniform, longer-lasting, and effective delivery of drugs within the brain, and may find use in the treatment of brain tumors, stroke, neuroinflammation, and other brain diseases where the blood-brain barrier is compromised or where local delivery strategies are feasible. PMID:22932224

Field Implementation Plan for the In-Situ Bioremediation Treatability Study at the Technical Area-V Groundwater Area of Concern

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Jun

This Field Implementation Plan (FIP) was prepared by Sandia National Laboratories, New Mexico (SNL/NM) and provides instruction on conducting a series of in-situ bioremediation (ISB) tests as described in the Revised Treatability Study Work Plan for In-Situ Bioremediation at the Technical Area-V Groundwater Area of Concern, referred to as the Revised Work Plan in this FIP. The Treatability Study is designed to gravity inject an electron-donor substrate and bioaugmentation bacteria into groundwater via three injection wells to perform bioremediation of the constituents of concern (COCs), nitrate and trichloroethene (TCE), in the regions with the highest concentrations at the Technical Area-Vmore » Groundwater (TAVG) Area of Concern (AOC). The Treatability Study will evaluate the effectiveness of bioremediation solution delivery and COC treatment over time. This FIP is designed for SNL/NM work planning and management. It is not intended to be submitted for regulator’s approval. The technical details presented in this FIP are subject to change based on field conditions, availability of equipment and materials, feasibility, and inputs from Sandia personnel and Aboveground Injection System contractor.« less

Progress in LPI Experiments at the NikeLaser

NASA Astrophysics Data System (ADS)

Weaver, J.; Kehne, D.; Obenschain, S.; Schmitt, A.; Serlin, V.; Oh, J.; Lehmberg, R.; Tsung, F.; McKenty, P.; Seely, J.

2014-10-01

The experimental program at the Nike laser facility at NRL is studying laser plasma instabilities (LPI) in the quarter critical region and cross-beam energy transport (CBET). The Nike krypton-fluorine (KrF) laser has unique characteristics that allow parametric studies of LPI. These features include short wavelength (248 nm), large bandwidth (~2-3 THz), beam smoothing by induced spatial incoherence (ISI), and full aperture focal spot zooming during the laser pulse. Nike also has a unique beam geometry that combines two widely separated beam arrays (145° in azimuth) with close beam-beam spacing (as low as 3.5°) within the main drive array. Particularly relevant for the CBET studies, recent campaigns have demonstrated the capability to alter the laser bandwidth by a factor of ~10 as well as shifts in the peak laser wavelength. An extensive LPI diagnostic suite is available for observation of stimulated Raman scattering, two-plasmon decay, stimulated Brillouin scattering, the parametric decay instability, and hard x-ray emission due to hot electrons. An overview of the observations of scattered laser light made during the previous studies of instabilities in the quarter critical region will be presented. Ongoing analysis of observed LPI emission from rotated targets will also be included. Plans for upcoming experiments related to quarter critical instabilities and CBET will be discussed. Work supported by DoE/NNSA.

A Compendium of Energy Conservation Success Stories

DOE R&D Accomplishments Database

1988-09-01

Three-quarters of DOE's Conservation R and D funds have been devoted to technology research and development: basic and applied research, exploratory R and D, engineering feasibility studies, pilot-scale prototype R and D, and technology demonstration. Non R and D projects have involved technology assessment program planning and analysis, model development, technology transfer and consumer information, health effects and safety research, and technical support for rule making. The success stories summarized in this compendium fall into three general categories: Completed Technology Success Stories, projects that have resulted in new energy-saving technologies that are presently being used in the private sector; Technical Success Stories, projects that have produced or disseminated important scientific/technical information likely to result in future energy savings; Program Success Stories, non-R and D activities that have resulted in nationally significant energy benefits. The Energy Conservation research and development program at DOE is managed by the Office of Conservation under the direction of the Deputy Assistant Secretary for Conservation. Three subordinate Program Offices correspond to the buildings, transportation, and industrial end-use sectors. A fourth subordinate Program Office{endash}Energy Utilization Research{endash}sponsors research and technical inventions for all end-use sectors.

Biological applications and effects of optical masers

NASA Astrophysics Data System (ADS)

Ham, William T., Jr.; Mueller, Harold A.; Guerry, R. K.; Guerry, Dupont, III; Cleary, Stephan F.

1988-09-01

Threshold radiant exposures for retinal damage in 3 macaque monkeys are given for exposures of 0.5, 0.125 and 0.016 seconds duration to laser wavelengths 514.5 and 488 nm. Intravitreal injections of 5 x .00005 gm of Cu-Zn SOD were toxic to cornea, lens and retina of the rhesus monkey after a radiant exposure of 33 j/sq cm of 440 nm light. No further experiments with SOD are contemplated. Similar experiments with catalase will be tried during the first quarter of the second contract year. The effect of oxygen on retinal toxicity during exposure to wave-lengths 540, 640 and 840 nm were delayed by the untimely death of Dr. Millen, our consultant on anesthesiology and oxygen administration. Arrangements have been made to activate this program during the second contract year. Threshold data on 40 microsecond pulse trains cannot be obtained until the acoustic modulator can be incorporated into the Ar-Kr laser which was used during the contract year to produce exposures less than 1 second to 514.5 and 488 nm laser lines. Data on PRF's of 10 and 100 KHz and 1, 10 and 20 MHz will be obtained during the second contract year. The long-term experiment on cataractogenesis on 2 rhesus monkeys exposed to a near UV spectrum (330 to 420 nm) has been completed.

The effects of moderate coal cleaning on the microbial removal of organic sulfur. [Quarterly] technical report, December 1, 1991--February 29, 1992

DOE Office of Scientific and Technical Information (OSTI.GOV)

Srivastava, V.J.

The purpose of this project is to investigate the possibilities of developing an integrated physical/chemical/microbial process for the pre-combustion removal of sulfur from coal. Microorganisms are capable of specifically cleaving carbon-sulfur bonds and removing substantial amounts of organic sulfur from coal; however, the removal of organic sulfur form coal by microorganisms is hampered by the fact that, as a solid substrate, it is difficult to bring microorganisms in contact with the entirety of a coal sample. This study will examine the suitability of physically/chemically treated coal samples for subsequent biodesulfurization. During the current quarter, chemical comminution and combined chemical treatment/explosivemore » comminution experiments have been performed to generate coal samples with increased surface area and porosity. Ammonia vapor was found to be the most effective chemical comminution agent and the optimum conditions for combined chemical treatment/explosive comminution have not yet been determined.« less

Ultraviolet Thomson Scattering from Direct-Drive Coronal Plasmas

NASA Astrophysics Data System (ADS)

Henchen, R. J.; Goncharov, V. N.; Michel, D. T.; Follett, R. K.; Katz, J.; Froula, D. H.

2013-10-01

Ultraviolet (λ4 ω = 263 nm) Thomson scattering (TS) was used to probe ion-acoustic waves (IAW's) and electron plasma waves (EPW's) from direct-drive coronal plasmas. Fifty-nine drive beams (λ3 ω = 351 nm) illuminate a spherical target with a radius of ~860 μm. Advances in the ultraviolet (UV) TS diagnostic at the Omega Laser Facility provide the ability to detect deep UV photons (~190 nm) and allow access to scattered light from EPW's propagating near the 3 ω quarter-critical surface (~2.5 × 1021 cm-3) . A series of experiments studied the effects of ablator materials on coronal plasma conditions. Electron temperatures and densities were measured from 150 μm to 400 μm from the initial target surface. Standard CH shells were compared to three-layered shells consisting of Si doped CH, Si, and Be. Early analysis indicates that these multilayered targets have less hot-electron energy as a result of higher electron temperature in the coronal plasma. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Characterization of long-scale-length plasmas produced from plastic foam targets for laser plasma instability (LPI) research

NASA Astrophysics Data System (ADS)

Oh, Jaechul; Weaver, J. L.; Serlin, V.; Obenschain, S. P.

2017-10-01

We report on an experimental effort to produce plasmas with long scale lengths for the study of parametric instabilities, such as two plasmon decay (TPD) and stimulated Raman scattering (SRS), under conditions relevant to fusion plasma. In the current experiment, plasmas are formed from low density (10-100 mg/cc) CH foam targets irradiated by Nike krypton fluoride laser pulses (λ = 248 nm, 1 nsec FWHM) with energies up to 1 kJ. This experiment is conducted with two primary diagnostics: the grid image refractometer (Nike-GIR) to measure electron density and temperature profiles of the coronas, and time-resolved spectrometers with absolute intensity calibration to examine scattered light features of TPD or SRS. Nike-GIR was recently upgraded with a 5th harmonic probe laser (λ = 213 nm) to access plasma regions near quarter critical density of 248 nm light (4.5 ×1021 cm-3). The results will be discussed with data obtained from 120 μm scale-length plasmas created on solid CH targets in previous LPI experiments at Nike. Work supported by DoE/NNSA.

Results for the first quarter calendar year 2017 tank 50H salt solution sample

DOE Office of Scientific and Technical Information (OSTI.GOV)

Crawford, C. L.

2017-04-12

In this memorandum, the chemical and radionuclide contaminant results from the First Quarter Calendar Year 2017 (CY17) sample of Tank 50H salt solution are presented in tabulated form. The First Quarter CY17 Tank 50H samples [a 200 mL sample obtained 6” below the surface (HTF-50-17-7) and a 1 L sample obtained 66” from the tank bottom (HTF-50-17-8)] were obtained on January 15, 2017 and received at Savannah River National Laboratory (SRNL) on January 16, 2017. Prior to obtaining the samples from Tank 50H, a single pump was run at least 4.4 hours and the samples were pulled immediately after pumpmore » shut down. All volatile organic analysis (VOA) and semi-volatile organic analysis (SVOA) were performed on the surface sample and all other analyses were performed on the variable depth sample. The information from this characterization will be used by Savannah River Remediation (SRR) for the transfer of aqueous waste from Tank 50H to the Saltstone Production Facility, where the waste will be treated and disposed of in the Saltstone Disposal Facility. This memorandum compares results, where applicable, to Saltstone Waste Acceptance Criteria (WAC) limits and targets. The chemical and radionuclide contaminant results from the characterization of the First Quarter CY17 sampling of Tank 50H were requested by SRR personnel and details of the testing are presented in the SRNL Task Technical and Quality Assurance Plan (TTQAP). This memorandum is part of Deliverable 2 from SRR request. Data pertaining to the regulatory limits for Resource Conservation and Recovery Act (RCRA) metals will be documented at a later time per the TTQAP for the Tank 50H saltstone task.« less

Responsive copolymers for enhanced petroleum recovery. Quarterly technical progress report, June 23--September 21, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

McCormick, C.; Hester, R.

Summaries are given on the technical progress on three tasks of this project. Monomer and polymer synthesis discusses the preparation of 1(7-aminoheptyloxymethyl)naphthalene and poly(maleic anhydride-alt-ethyl vinyl ether). Task 2, Characterization of molecular structure, discusses terpolymer solution preparation, UV analysis, fluorescence analysis, low angle laser light scattering, and viscometry. The paper discusses the effects of hydrophobic groups, the effect of pH, the effect of electrolyte addition, and photophysical studies. Task 3, Solution properties, describes the factorial experimental design for characterizing polymer solutions by light scattering, the light scattering test model, orthogonal factorial test design, linear regression in coded space, confidence levelmore » for coded space test mode coefficients, coefficients of the real space test model, and surface analysis of the model equations.« less

Small image laser range finder for planetary rover

NASA Technical Reports Server (NTRS)

Wakabayashi, Yasufumi; Honda, Masahisa; Adachi, Tadashi; Iijima, Takahiko

1994-01-01

A variety of technical subjects need to be solved before planetary rover navigation could be a part of future missions. The sensors which will perceive terrain environment around the rover will require critical development efforts. The image laser range finder (ILRF) discussed here is one of the candidate sensors because of its advantage in providing range data required for its navigation. The authors developed a new compact-sized ILRF which is a quarter of the size of conventional ones. Instead of the current two directional scanning system which is comprised of nodding and polygon mirrors, the new ILRF is equipped with the new concept of a direct polygon mirror driving system, which successfully made its size compact to accommodate the design requirements. The paper reports on the design concept and preliminary technical specifications established in the current development phase.

Service use and financial performance in a replication program on adult day centers.

PubMed

Reifler, B V; Cox, N J; Jones, B N; Rushing, J; Yates, K

1999-01-01

The authors describe results from Partners in Caregiving: The Dementia Services Program, and present information on service utilization and financial performance among a group of 48 adult day centers across the United States from 1992 to 1996. Centers, with nonrandom assignment, received either grant support (average value: $93,000) or intensive technical assistance (average value: $39,000). Sites reported baseline data and submitted utilization information (enrollment and census) and financial data (revenue and expenses) quarterly. Overall, there were significant increases in enrollment, census, and financial performance (percent of cash expenses met through operating revenue) over the 4-year period. The grant-supported and technical-assistance sites had similar rates of improvement. Results provide data on service utilization and financial performance and demonstrate gains that can be achieved in these areas through improved marketing and financial management.

DEVELOPMENT OF A VALIDATED MODEL FOR USE IN MINIMIZING NOx EMISSIONS AND MAXIMIZING CARBON UTILIZATION WHEN CO-FIRING BIOMASS WITH COAL

DOE Office of Scientific and Technical Information (OSTI.GOV)

Larry G. Felix; P. Vann Bush

2002-10-26

This is the eighth Quarterly Technical Report for DOE Cooperative Agreement No. DE-FC26-00NT40895. A statement of the project objectives is included in the Introduction of this report. The final biomass co-firing test burn was conducted during this quarter. In this test (Test 14), up to 20% by weight dry switchgrass was comilled with Jim Walters No.7 mine coal and injected through the single-register burner. Jim Walters No.7 coal is a low-volatility, low-sulfur ({approx}0.7% S) Eastern bituminous coal. The results of this test are presented in this quarterly report. Progress has continued to be made in implementing a modeling approach tomore » combine reaction times and temperature distributions from computational fluid dynamic models of the pilot-scale combustion furnace with char burnout and chemical reaction kinetics to predict NO{sub x} emissions and unburned carbon levels in the furnace exhaust. The REI Configurable Fireside Simulator (CFS) is now in regular use. Presently, the CFS is being used to generate CFD calculations for completed tests with Powder River Basin coal and low-volatility (Jim Walters No.7 Mine) coal. Niksa Energy Associates will use the results of these CFD simulations to complete their validation of the NOx/LOI predictive model. Work has started on the project final report.« less

[Testing and commercialization of a cotton stalk shredder and plow]. Technical progress report, October--December 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thacker, G.W.

1996-01-27

This quarterly report describes work on Task 1: Field test and sell prototype to Ellis Equipment, Ltd; Task 2: Design, build, and field test two prototypes; and Task 3: Produce and sell Pegasus to farmers. The equipment has been built to shred stalks, deeply till the soil, and prepare seedbeds for cotton plants. The equipment has been field tested in Australia and is currently being field tested in California and Arizona. Unexpected problems appeared with hard dry soils and this report describes improvements made.

Proof of the Feasibility of Coherent and Incoherent Schemes for Pumping a Gamma-Ray Laser

DTIC Science & Technology

1988-10-01

TheUnierstyof Texas. at Dallas Center for’ "Quantum, Electronics The IGamm~a-7Ra~y.,La’ser. Project o Qua’rter’l y’ Report SJuly-September .1988 Co...Dallas Center for Quantum Electronics P.O. Box 830688 Richardson, Texas 75083-0688 October 1988 0 Quarterly Technical Progress Report 1 July 1988...ADDRESS 10. PROGRAM ELEMENT. PROJECT, TASKAREA & WORK UNIT NUM9ERS University of Texas at Dallas Center for Quantum Electronics P.O. Box 830688

Quarterly Performance/Technical Report of the National Marrow Donor Program

DTIC Science & Technology

2008-02-05

HLA-DRB1 High Resolution Typing Closed 9 IIB.1.3 Aim 3 – Evaluate HLA-C Typing of Donors Closed 9 IIB.1.4 Aim 4 – Evaluate Buccal Swabs Open 10 IIB...December 31, 2007 10 of 21 IIB.1.4 Aim 4: Evaluate Buccal Swabs Period 5 Activity: In April of 2006, the NMDP transitioned to the use of... buccal swabs for the collection of DNA samples from newly recruited donors. To support this change in sample type, Quality Control samples for donor

Secure Distributed Processing Systems: Quarterly Technical Reports, 1 July 1977 - 30 April 1978

DTIC Science & Technology

1978-06-01

choice does not assure that the network is encrypted. Thus, process - process encryption seems to be the highest safe choice . The details of the...site, except for the one where the LC is located, there is a local l°ck^f^16^ n r Those processes are responsible for ia^tainlnTa ?ocal copy of the...ed into the LOCK table at every site in a subsequent phase of the recovery process In ^nmary, the LOR B«ohanlsm amounts to electing a neH LC for

NASA Sun-Earth Connections Theory Program: The Structure and Dynamics of the Solar Corona and Inner Heliosphere

NASA Technical Reports Server (NTRS)

Mikic, Zoran; Grebowsky, Joseph M. (Technical Monitor)

2001-01-01

This report covers technical progress during the fourth quarter of the second year of NASA Sun-Earth Connections Theory Program (SECTP) contract 'The Structure and Dynamics of the Solar Corona and Inner Heliosphere,' NAS5-99188, between NASA and Science Applications International Corporation, and covers the period May 16,2001 to August 15, 2001. Under this contract SAIC and the University of California, Irvine (UCI) have conducted research into theoretical modeling of active regions, the solar corona, and the inner heliosphere, using the MHD model.

Combined Quarterly Technical Report Number 31. Pluribus Satellite IMP (Interface Message Provision) Development Mobile Access Terminal Network

DTIC Science & Technology

1983-12-01

Bzo I-BIO-INODE I<---->INODE 1-SIO-I BIO I 2 Hbps <-I I LINKI #1 1 B’?LY 1 #2 I LINKI 1-> 2 bps - ----- SWITCH .---- • OR N,2 11bps ->IIJPLIN I...IPROC’Rh IPROC’RI IDOWNLINKI-> 2 14bps I BIO I-BIO-INODE I<---->INODE I-BIO-I BIO I S2 bps ->I I LINKI #1 I B’FLY 1 #2 I LINKI 1-> 2 1bps " ----- + SWITCH

The Structure and Dynamics of the Solar Corona and Inner Heliosphere

NASA Technical Reports Server (NTRS)

Mikic, Zoran; Grebowsky, J. (Technical Monitor)

2002-01-01

This report covers technical progress during the fourth quarter of the second year of NASA Sun-Earth Connections Theory Program (SECTP) contract "The Structure and Dynamics of the Solar Corona and Inner Heliosphere," NAS5-99188, between NASA and Science Applications International Corporation (SAIC), and covers the period May 16, 2001 to August 15, 2001. Under this contract SAIC and the University of California, Irvine (UCI) have conducted research into theoretical modeling of active regions, the solar corona, and the inner heliosphere, using the MHD (magnetohydrodynamic) model.

Communication Techniques in Stressed Environments

DTIC Science & Technology

1991-11-01

The workshop was held May 14-17, 1989 in Ruidoso , New Mexico. The program is as follows: Session 1 - Modulation Characterization Charles L. Weber...Ontario Canada April 24-27, 1989, to attend and deliver 2 technical presentations at IEEE INFOCOM 󈨝. • Dr. Robert Scholtz travelled to Ruidoso , NM...to coordinate the CSI Workshop "Ad- vanced Communication Processing Techniques", May 14-17, 1989. • Dr. Charles Weber travelled to Ruidoso , NM, to

Ionospheric Irregularity Physics Modelling.

DTIC Science & Technology

1982-02-09

NUMBERS Washington, DC 20375 62715H; 47-0889-0-2 II CONTROLLING OFFICE NAME AND ADDRESS 12 REPORT DATE Defense Nuclear Agency February 9, 1982 Washington... CONTROL TECHNICAL CENTER COMMANDER PE TAGON RM SF 685 FIELD COMMAND WASHINGTON, D.C. 20301 DEFENSE NUCLEAR AGENCY OICY ATTN C-650 KIRTLAND, AFR, NM...BUILDINICG KIRTLAND AFB, NM 87115 1400 WILSON BLVD. OICY ATTN DOCUMENT CONTROL ARLINGTON, 11A. 22209 OICY ATTN NUCLEAR MONITORING RESEARCH JOINT CHIEFS OF

Publications of the Jet Propulsion Laboratory, January - December 1973. [bibliography

NASA Technical Reports Server (NTRS)

1974-01-01

Five classes of publications are included in this bibliography: (1) Technical Reports in which the information is complete for a specific accomplishment and is intended for a wide audience. (2) Articles from the bimonthly Deep Space Network Progress Report. Each volume's collection of articles presents a periodical survey of current accomplishments by the Deep Space Network. (3) Technical Memorandums, in which the information is complete for a specific accomplishment but is intended for a limited audience to satisfy unique requirements. (4) Articles from the JPL Quarterly Technical Review. Each article summarizes a recent important development, interim or final results, or an advancement in the state of the art in a scientific or engineering endeavor, This publication has been discontinued, and the issues indexed in this bibliography are the last to be published. (5) Articles published in the open literature. The publications are indexed by: (1) author, (2) subject, and (3) publication type and number. A descriptive entry appears under the name of each author of each publication; an abstract is included with the entry for the primary (first-listed) author.

A systematic assessment of the state of hazardous waste clean-up technologies. Quarterly technical progress report, April 1--June 30, 1993

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berg, M.T.; Reed, B.E.; Gabr, M.

1993-07-01

West Virginia University (WVU) and the US DOE Morgantown Energy Technology Center (METC) entered into a Cooperative Agreement on August 29, 1992 entitled ``Decontamination Systems Information and Research Programs.`` Stipulated within the Agreement is the requirement that WVU submit to METC a series of Technical Progress Report for Year 1 of the Agreement. This report reflects the progress and/or efforts performed on the following nine technical projects encompassed by the Year 1 Agreement for the period of April 1 through June 30, 1993: Systematic assessment of the state of hazardous waste clean-up technologies; site remediation technologies -- drain-enhanced soil flushingmore » (DESF) for organic contaminants removal; site remediation technologies -- in situ bioremediation of organic contaminants; excavation systems for hazardous waste sites; chemical destruction of polychlorinated biphenyls; development of organic sensors -- monolayer and multilayer self-assembled films for chemical sensors; Winfield lock and dam remediation; Assessments of Technologies for hazardous waste site remediation -- non-treatment technologies and pilot scale test facility implementation; and remediation of hazardous sites with stream reforming.« less

NASA/WVU Software Research Laboratory, 1995

NASA Technical Reports Server (NTRS)

Sabolish, George J.; Callahan, John R.

1995-01-01

In our second year, the NASA/WVU Software Research Lab has made significant strides toward analysis and solution of major software problems related to V&V activities. We have established working relationships with many ongoing efforts within NASA and continue to provide valuable input into policy and decision-making processes. Through our publications, technical reports, lecture series, newsletters, and resources on the World-Wide-Web, we provide information to many NASA and external parties daily. This report is a summary and overview of some of our activities for the past year. This report is divided into 6 chapters: Introduction, People, Support Activities, Process, Metrics, and Testing. The Introduction chapter (this chapter) gives an overview of our project beginnings and targets. The People chapter focuses on new people who have joined the Lab this year. The Support chapter briefly lists activities like our WWW pages, Technical Report Series, Technical Lecture Series, and Research Quarterly newsletter. Finally, the remaining four chapters discuss the major research areas that we have made significant progress towards producing meaningful task reports. These chapters can be regarded as portions of drafts of our task reports.

High Acceptability of HIV Self-Testing among Technical Vocational Education and Training College Students in Gauteng and North West Province: What Are the Implications for the Scale Up in South Africa?

PubMed

Mokgatle, Mathildah Mpata; Madiba, Sphiwe

2017-01-01

Although HIV self-testing (HIVST) is globally accepted as an important complement to existing HIV testing approaches, South Africa has lagged behind in its adoption. As a result, data on the acceptability and uptake of HIVST testing is limited. The study investigated the acceptability of HIVST among students in Technical Vocational Education and Training (TVET) colleges in two provinces in South Africa. A cross-sectional survey using a self-administered structured questionnaire was used to collect data among 3,662 students recruited from 13 TVET colleges. The mean age of the students was 21.9 years. The majority (80.9%) were sexually active; while 66.1% reported that they had one sexual partner, and 33.9% had two or more sexual partners in the past year, and66.5% used condoms during the last sexual act. Three-quarters tested for HIV in the past year but less than half knew about HIVST prior to the survey. The acceptability of HIVST was high; about three-quarters showed a willingness to purchase a self-test kit and a majority would self-test with partners. Acceptability of HIVST was associated with being sexually active (OR = 1.73, p = 0.02, confidence interval (CI): 1.08-2.75), having ever been tested for HIV (OR = 1.74, p = 0.001, CI: 1.26-2.38), and having multiple sexual partners (OR = 0.61, p = 0.01, CI: 0.42-0.88). Three-quarters would confirm test results at a local health facility. In terms of counselling, telephone hotlines were acceptable to only 39.9%, and less than half felt that test-kit leaflets would provide sufficient information to self-test. The high acceptability of HIVST among the students calls for extensive planning and preparation for the scaling up of HIVST in South Africa. In addition, campaigns similar to those conducted to promote HIV counselling and testing (HCT) should be considered to educate communities about HIVST.

High Acceptability of HIV Self-Testing among Technical Vocational Education and Training College Students in Gauteng and North West Province: What Are the Implications for the Scale Up in South Africa?

PubMed Central

Mokgatle, Mathildah Mpata; Madiba, Sphiwe

2017-01-01

Background Although HIV self-testing (HIVST) is globally accepted as an important complement to existing HIV testing approaches, South Africa has lagged behind in its adoption. As a result, data on the acceptability and uptake of HIVST testing is limited. The study investigated the acceptability of HIVST among students in Technical Vocational Education and Training (TVET) colleges in two provinces in South Africa. Methods A cross-sectional survey using a self-administered structured questionnaire was used to collect data among 3,662 students recruited from 13 TVET colleges. Results The mean age of the students was 21.9 years. The majority (80.9%) were sexually active; while 66.1% reported that they had one sexual partner, and 33.9% had two or more sexual partners in the past year, and66.5% used condoms during the last sexual act. Three-quarters tested for HIV in the past year but less than half knew about HIVST prior to the survey. The acceptability of HIVST was high; about three-quarters showed a willingness to purchase a self-test kit and a majority would self-test with partners. Acceptability of HIVST was associated with being sexually active (OR = 1.73, p = 0.02, confidence interval (CI): 1.08–2.75), having ever been tested for HIV (OR = 1.74, p = 0.001, CI: 1.26–2.38), and having multiple sexual partners (OR = 0.61, p = 0.01, CI: 0.42–0.88). Three-quarters would confirm test results at a local health facility. In terms of counselling, telephone hotlines were acceptable to only 39.9%, and less than half felt that test-kit leaflets would provide sufficient information to self-test. Interpretations The high acceptability of HIVST among the students calls for extensive planning and preparation for the scaling up of HIVST in South Africa. In addition, campaigns similar to those conducted to promote HIV counselling and testing (HCT) should be considered to educate communities about HIVST. PMID:28141858

Teaching Technical Competencies for Fluid Mechanics Research

NASA Astrophysics Data System (ADS)

Tagg, Randall

2014-11-01

We are developing an ``on demand'' framework for students to learn techniques used in fluid mechanics research. The site for this work is a university-grade laboratory situated next to Gateway High School in Aurora, Colorado. Undergraduate university students work with K-12 students on research and technical innovation projects. Both groups need customized training as their projects proceed. A modular approach allows particular competencies such as pump selection, construction of flow piping and channels, flow visualization, and specific flow measurement methods to be acquired through focused lessons. These lessons can be learned in either a stand-alone fashion or assembled into units for formal courses. A research example was a student project on diffusion of infectious material in micro-gravity in the event of an intestinal puncture wound. A curriculum example is a 9-week quarter of high-school instruction on instrumentation that uses small-scale water treatment systems as a case study.

GRACE Follow-On and Potential Successors: Mission Options for the Upcoming Decadaes

NASA Astrophysics Data System (ADS)

Watkins, M. M.

2017-12-01

The GRACE Follow-On mission is currently scheduled to launch in the first quarter of 2018, providing a successor to GRACE for ongoing critical measurements of Earth's time varying mass distribution for the coming decade. As noted in the literature (and in several talks in this session), there are also several possible mission proposals and technologies to either augment or succeed GRACE FO for extended and improved measurements. Various scientific, programmatic, and technical issues drive each of these potential missions and these factors will be important in determining which will ultimately be selected for flight. These issues include accuracy requirements based on science goals, technical maturity, cost, and international partnership options. In this talk, we will provide a final detailed update before launch on the GRACE Follow-On status and expectations, and we will outline several of the key options for future missions after GRACE FO.

Increasing the quality and germination gymnosperms by photonics methods

NASA Astrophysics Data System (ADS)

Iakovlev, Alexey; Durova, Anastasia; Kascheev, Sergey; Grishkanich, Aleksandr; Mak, Andrey; Ruzankina, Julia

2017-02-01

The research of seed sowing qualities demonstrates the considerable influence of laser irradiation on seeds of different species that are essential for the forestry of Russian Federation. For experiment, we used seeds of Spruce fir (Pícea ábies) and Siberian larch (Lárix sibírica). The seeds were exposed to radiation of the following wavelengths: 405 nm 500 mW, 450 nm 3000 mW, 532 nm 550 mW, 640 nm 1000 mW. The results show that laser exposure of seeds has positive impact on growth rate, technical germination ability, root formation, and more over on establishment and root formation while grafting. In experiments is obtained increasing germination by 15% and the germination time to 10%.

Donor Hemovigilance with Blood Donation

PubMed Central

Diekamp, Ulrich; Gneißl, Johannes; Rabe, Angela; Kießig, Stephan T.

2015-01-01

Background Reports on unexpected events (UEs) during blood donation (BD) inadequately consider the role of technical UEs. Methods Defined local and systemic UEs were graded by severity; technical UEs were not graded. On January 1, 2008, E.B.P.S.-Logistics (EBPS) installed the UE module for plasma management software (PMS). Donor room physicians entered UEs daily into PMS. Medical directors reviewed entries quarterly. EBPS compiled data on donors, donations, and UEs from January 1, 2008 to June 30, 2011. Results 6,605 UEs were observed during 166,650 BDs from 57,622 donors for a corrected incidence of 4.30% (0.66% local, 1.59% systemic, 2.04% technical UEs). 2.96% of BDs were accompanied by one UE and 0.45% by >1 UE (2-4). 6.3% of donors donating blood for their first time, 3.5% of those giving blood for their second time, and 1.9% of donors giving their third or more BD experienced UEs. Most common UEs were: discontinued collections due to venous access problems, repeated venipuncture, and small hematomas. Severe circulatory UEs occurred at a rate of 16 per 100,000 BDs. Conclusions Technical UEs were common during BD. UEs accompanied first and second donations significantly more often than subsequent donations. PMID:26195932

Donor Hemovigilance during Preparatory Plasmapheresis

PubMed Central

Diekamp, Ulrich; Gneißl, Johannes; Rabe, Angela; Kießig, Stephan T.

2014-01-01

Summary Background Reports on unexpected donor events (UEs) during preparatory plasmapheresis (PPP) are scarce, and rarely consider technical UEs. Methods Defined local and systemic UEs were graded by severity; technical UEs were not graded. On January 1, 2008, E.B.P.S.-Logistics (EBPS) installed the UE module for plasma management software (PMS). Donor room physicians entered UEs daily into the PMS. Medical directors reviewed entries quarterly. EBPS compiled data on donors, donations and UEs from January 1, 2008 to June 30, 2011. Results 66,822 UEs were observed during 1,107,846 PPPs for a corrected incidence of 6.55% (1.4% local, 0.55% systemic, 4.6% technical UEs). 3.36% of PPPs were accompanied by 1 UE and 1.18% by >1 UE (2-5). 13.7% of donors undergoing PPP for the first time, 9.7% of those having a second PPP and 4.0% of those having a third or more PPPs were associated with UEs. Most common UEs were repeated venipuncture, and broken-off collection due to venous access problems and small hematomas. Severe systemic UEs occurred at a rate of 36 per 100,000 PPPs. Conclusions Technical UEs were common with PPP. UEs accompanied first and second donations significantly more frequently than for subsequent donations. PMID:24847188

Discrimination and quantification of autofluorescence spectra of human lung cells

NASA Astrophysics Data System (ADS)

Rahmani, Mahya; Khani, Mohammad Mehdi; Khazaei Koohpar, Zeinab; Molik, Paria

2016-10-01

To study laser-induced autofluorescence spectroscopy of the human lung cell line, we evaluated the native fluorescence properties of cancer QU-DB and normal MRC-5 human lung cells during continuous exposure to 405 nm laser light. Two emission bands centered at ~470 nm and ~560 nm were observed. These peaks are most likely attributable to mitochondrial fluorescent reduced nicotinamide adenine dinucleotide and riboflavin fluorophores, respectively. This article highlights lung cell autofluorescence characterization and signal discrimination by collective investigation of different spectral features. The absolute intensity, the spectral shape factor or redox ratio, the full width of half-maximum and the full width of quarter maximum was evaluated. Moreover, the intensity ratio, the area under the peak and the area ratio as a contrast factor for normal and cancerous cells were also calculated. Among all these features it seems that the contrast factor precisely and significantly discriminates the spectral differences of normal and cancerous lung cells. On the other hand, the relative quantum yield for both cell types were found by comparing the quantum yield of an unknown compound with known fluorescein sodium as a reference solution.

Quarterly Technical Progress Report - Investigation of Syngas Interaction in Alcohol Synthesis Catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murty A. Akundi

This report presents the work done on " Investigation of Syngas Interaction in Alcohol Synthesis Catalysts" during the last quarter. The major activity during this period is on FTIR absorption studies of Co/Cr catalysts using CO as a probe molecule. Transition metals cobalt and copper play significant roles in the conversion of syngas (CO + H2 ) to liquid fuels. With a view to examine the nature of interaction between CO and metal, the FTIR spectra of CO adsorbed on Co-Cr2 O3 composites were investigated. The results indicate that as cobalt loading increases, the intensity of the CO adsorption bandsmore » increase and several vibrational modes seem to be promoted. Heat treatment of the sample revealed two distinct processes of adsorption. Bands due to physisorption disappeared while bands due to chemisorption not only increased in intensity but persisted even after desorption. It seems that the physisorption process is more active when the catalyst is fresh and is hindered when carbidic/carbonyl formations occur on the metal surfaces.« less

Development of cost-effective surfactant flooding technology, Quarterly report, October 1995--December 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pope, G.A.; Sepehrnoori, K.

1995-12-31

The objective of this research is to develop cost-effective surfactant flooding technology by using simulation studies to evaluate and optimize alternative design strategies taking into account reservoir characteristics process chemistry, and process design options such as horizontal wells. Task 1 is the development of an improved numerical method for our simulator that will enable us to solve a wider class of these difficult simulation problems accurately and affordably. Task 2 is the application of this simulator to the optimization of surfactant flooding to reduce its risk and cost. In this quarter, we have continued working on Task 2 to optimizemore » surfactant flooding design and have included economic analysis to the optimization process. An economic model was developed using a spreadsheet and the discounted cash flow (DCF) method of economic analysis. The model was designed specifically for a domestic onshore surfactant flood and has been used to economically evaluate previous work that used a technical approach to optimization. The DCF model outputs common economic decision making criteria, such as net present value (NPV), internal rate of return (IRR), and payback period.« less

Development and utilization of new diagnostics for dense-phase pneumatic transport. Quarterly technical progress report, October 1-December 31, 1989

DOE Office of Scientific and Technical Information (OSTI.GOV)

Louge, M. Y.; Jenkins, J. T.

The main objective of this work is to develop probes for local measurements of solid velocity and holdup in dense gas-solid flows. In particular, capacitance probes are designed to measure local, time-dependent particle concentrations. In addition, a new optical fiber probe based on laser-induced-phosphorescence is developed to measure particle velocities. The principles for the capacitance and optical diagnostics were given in our first and second quarterly reports. In this reporting period, we have demonstrated with success the feasibility of the optical fiber probe. Another objective of this work is to develop a model of dense-phase conveying and to test thismore » model in a setup that incorporates our diagnostics. In this period, as a prelude to these modeling efforts scheduled for the third year of the contract, we have carried out additional computer simulations of rapid granular flows to verify the theories of Jenkins and Richman (1988) on the anisotropy of the second moment in simple shear. 2 refs., 5 figs.« less

Taos Smart Growth Implementation Assistance: Concepts for the Paseo del Pueblo Sur Corridor

EPA Pesticide Factsheets

This report describes a technical assistance project with Taos, NM, to help make development along State Highway 68, the Paseo del Pueblo Sur commercial corridor, economically stronger and more attractive.

A simplified method for generating periodic nanostructures by interference lithography without the use of an anti-reflection coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kapon, Omree; Muallem, Merav; Palatnik, Alex

Interference lithography has proven to be a useful technique for generating periodic sub-diffraction limited nanostructures. Interference lithography can be implemented by exposing a photoresist polymer to laser light using a two-beam arrangement or more simply a one beam configuration based on a Lloyd's Mirror Interferometer. For typical photoresist layers, an anti-reflection coating must be deposited on the substrate to prevent adverse reflections from cancelling the holographic pattern of the interfering beams. For silicon substrates, such coatings are typically multilayered and complex in composition. By thinning the photoresist layer to a thickness well below the quarter wavelength of the exposing beam,more » we demonstrate that interference gratings can be generated without an anti-reflection coating on the substrate. We used ammonium dichromate doped polyvinyl alcohol as the positive photoresist because it provides excellent pinhole free layers down to thicknesses of 40 nm, and can be cross-linked by a low-cost single mode 457 nm laser, and can be etched in water. Gratings with a period of 320 nm and depth of 4 nm were realized, as well as a variety of morphologies depending on the photoresist thickness. This simplified interference lithography technique promises to be useful for generating periodic nanostructures with high fidelity and minimal substrate treatments.« less

Lower-free tropospheric ozone dial measurements over Athens, Greece

NASA Astrophysics Data System (ADS)

Mytilinaios, Michail; Papayannis, Alexandros; Tsaknakis, Georgios

2018-04-01

A compact ozone differential absorption lidar (DIAL) was implemented at the Laboratory of Laser Remote Sensing of the National Technical University of Athens (NTUA), in Athens, Greece. The DIAL system is based on a Nd:YAG laser emitting at 266 nm. A high-pressure Raman cell, filled with D2, was used to generate the λON and λOFF laser wavelength pairs (i.e., 266-289 nm and 289-316 nm, respectively) based on the Stimulated Raman Scattering (SRS) effect. The system was run during daytime and nighttime conditions to obtain the vertical profile of tropospheric ozone in the Planetary Boundary Layer (PBL) and the adjacent free troposphere.

Exploring Broad Area Quantum Cascade Lasers

DTIC Science & Technology

2017-10-01

Research Laboratory AFRL /RDLTD 3550 Aberdeen Ave SE Kirtland AFB, NM 87117-5776 11. SPONSOR/MONITOR’S REPORT NUMBER(S) AFRL -RD-PS-TP-2017-0008 12...LIST DTIC/OCP 8725 John J. Kingman Rd, Suite 0944 Ft Belvoir, VA 22060-6218 1 cy AFRL /RVIL Kirtland AFB, NM 87117-5776 1 cy Chunte Lu... AFRL -RD-PS- AFRL -RD-PS- TP-2017-0008 TP-2017-0008 EXPLORING BROAD AREA QUANTUM CASCADE LASERS Tim Newell, et. al. 1 October 2017 Technical

The Photodissociation of Nitromethane at 193 nm.

DTIC Science & Technology

1983-02-28

available energy for product translational + internal energy is 90 kcal/mole. As the largest amount of energy that goes into translational energy in the...CATAL.O8 NUMIER 0 R 92-545/21W83 P 3-/ 4. TITLE (and Subtlee) S. TYPE OF REPORT A PEI4o0 COVERED THE PHOTODISSOCIATION OF NITROMETHANE AT 193 NM Technical S...been investigated by two independent and comple- *_ mentary techniques, product emission spectroscopy and molecular beam photofragment translational

VIS-NIR multispectral synchronous imaging pyrometer for high-temperature measurements.

PubMed

Fu, Tairan; Liu, Jiangfan; Tian, Jibin

2017-06-01

A visible-infrared multispectral synchronous imaging pyrometer was developed for simultaneous, multispectral, two-dimensional high temperature measurements. The multispectral image pyrometer uses prism separation construction in the spectrum range of 650-950 nm and multi-sensor fusion of three CCD sensors for high-temperature measurements. The pyrometer had 650-750 nm, 750-850 nm, and 850-950 nm channels all with the same optical path. The wavelength choice for each channel is flexible with three center wavelengths (700 nm, 810 nm, and 920 nm) with a full width at half maximum of the spectrum of 3 nm used here. The three image sensors were precisely aligned to avoid spectrum artifacts by micro-mechanical adjustments of the sensors relative to each other to position them within a quarter pixel of each other. The pyrometer was calibrated with the standard blackbody source, and the temperature measurement uncertainty was within 0.21 °C-0.99 °C in the temperatures of 600 °C-1800 °C for the blackbody measurements. The pyrometer was then used to measure the leading edge temperatures of a ceramics model exposed to high-enthalpy plasma aerodynamic heating environment to verify the system applicability. The measured temperature ranges are 701-991 °C, 701-1134 °C, and 701-834 °C at the heating transient, steady state, and cooling transient times. A significant temperature gradient (170 °C/mm) was observed away from the leading edge facing the plasma jet during the steady state heating time. The temperature non-uniformity on the surface occurs during the entire aerodynamic heating process. However, the temperature distribution becomes more uniform after the heater is shut down and the experimental model is naturally cooled. This result shows that the multispectral simultaneous image measurement mode provides a wider temperature range for one imaging measurement of high spatial temperature gradients in transient applications.

Point-of-use water disinfection using ultraviolet and visible light-emitting diodes.

PubMed

Lui, Gough Yumu; Roser, David; Corkish, Richard; Ashbolt, Nicholas J; Stuetz, Richard

2016-05-15

Improvements in point-of-use (POU) drinking water disinfection technologies for remote and regional communities are urgently needed. Conceptually, UV-C light-emitting diodes (LEDs) overcome many drawbacks of low-pressure mercury tube based UV devices, and UV-A or visible light LEDs also show potential. To realistically evaluate the promise of LED disinfection, our study assessed the performance of a model 1.3 L reactor, similar in size to solar disinfection bottles. In all, 12 different commercial or semi-commercial LED arrays (270-740 nm) were compared for their ability to inactivate Escherichia coli K12 ATCC W3110 and Enterococcus faecalis ATCC 19433 over 6h. Five log10 and greater reductions were consistently achieved using the 270, 365, 385 and 405 nm arrays. The output of the 310 nm array was insufficient for useful disinfection while 430 and 455 nm performance was marginal (≈ 4.2 and 2.3-log10s E. coli and E. faecalis over the 6h). No significant disinfection was observed with the 525, 590, 623, 660 and 740 nm arrays. Delays in log-phase inactivation of E. coli were observed, particularly with UV-A wavelengths. The radiation doses required for >3-log10 reduction of E. coli and E. faecalis differed by 10 fold at 270 nm but only 1.5-2.5 fold at 365-455 nm. Action spectra, consistent with the literature, were observed with both indicators. The design process revealed cost and technical constraints pertaining to LED electrical efficiency, availability and lifetime. We concluded that POU LED disinfection using existing LED technology is already technically possible. UV-C LEDs offer speed and energy demand advantages, while UV-A/violet units are safer. Both approaches still require further costing and engineering development. Our study provides data needed for such work. Copyright © 2016 Elsevier B.V. All rights reserved.

Corrective Action Management Unit Report of Post-Closure Care Activities Calendar Year 2017.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ziock, Robert; Little, Bonnie Colleen

The Corrective Action Management Unit (CAMU) at Sandia National Laboratories, New Mexico (SNL/NM) consists of a containment cell and ancillary systems that underwent regulatory closure in 2003 in accordance with the Closure Plan in Appendix D of the Class 3 Permit Modification (SNL/NM September 1997). The containment cell was closed with wastes in place. On January 27, 2015, the New Mexico Environment Department (NMED) issued the Hazardous Waste Facility Operating Permit (Permit) for Sandia National Laboratories (NMED January 2015). The Permit became effective February 26, 2015. The CAMU is undergoing post-closure care in accordance with the Permit, as revised andmore » updated. This CAMU Report of Post-Closure Care Activities documents all activities and results for Calendar Year (CY) 2017 as required by the Permit. The CAMU containment cell consists of engineered barriers including a cover system, a bottom liner with a leachate collection and removal system (LCRS), and a vadose zone monitoring system (VZMS). The VZMS provides information on soil conditions under the cell for early leak detection. The VZMS consists of three monitoring subsystems, which include the primary subliner (PSL), a vertical sensor array (VSA), and the Chemical Waste Landfill (CWL) sanitary sewer (CSS) line. The PSL, VSA, and CSS monitoring subsystems are monitored quarterly for soil moisture concentration, the VSA is monitored quarterly for soil temperature, and the VSA and CSS monitoring subsystems are monitored annually for volatile organic compound (VOC) concentrations in the soil vapor at various depths. Baseline data for the soil moisture, soil temperature, and soil vapor were established between October 2003 and September 2004.« less

A Study to Determine the Most Effective Organizational Structure for Providing Supervision to the Medical Supply Specialist (MOS 786J) Assigned to the DMAA, WRAMC (Directorate of Medical Activities Administration, Walter Reed Army Medical Center)

DTIC Science & Technology

1988-07-22

to provide the DMAA 76Js with a better understanding of their technical skills and responsibilities ( Szilagyi and Wallace 216-217, 482-484). 3. To...Quarterly May 1986: 72-79. Szilagyi , Andrew 0. and Marc J. Wallace , Jr. Organizational Behavior and Performance. 3d ED. Glenview: Scott, Foresman and...activities) in the daily work environment of the DMAA 76Js due to the present organizational structure of the DMAA ( Szilagyi and Wallace 191). This was

Large scale solubilization of coal and bioconversion to utilizable energy. Eleventh quarterly technical progress report, April 1, 1996--June 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mishra, N.C.

1996-10-01

Neurospora has the capability to solubilize coal and the protein fraction accounting for this ability has been isolated. During this period the cola solubilizing activity (CSA) was fractionated and partially sequenced. The activity has been determined to be a tyrosinase and/or a phenol oxidase. The amino acid sequence of the protein was used to prepare oligonucleotides to identify the clone carrying Neurospora CSA. It is intended to clone the Neurospora gene into yeast, since yeast cannot solubilize coal, to further characterize the CSA.

Quarterly progress report for the Chemical and Energy Research Section of the Chemical Technology Division, April--June 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jubin, R.T.

The Chemical and Energy Research Section conducts basic and applied research and development in chemical engineering, applied chemistry, and bioprocessing, with an emphasis on energy-driven technologies and advanced chemical separations for nuclear and waste applications. The report describes the various tasks performed within six major areas of research: Hot Cell Operations, Process Chemistry and thermodynamics, Separations and Materials Synthesis, Solution Thermodynamics, biotechnology Research, and Molecular Studies. The name of a technical contact is included with each task described, and readers are encouraged to contact these individuals if they need additional information.

DOE FES FY2017 Joint Research Target Fourth Quarter Milestone Report for theNational Spherical Torus Experiment Upgrade.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Soukhanovskii, V. A.

2017-09-13

A successful high-performance plasma operation with a radiative divertor has been demonstrated on many tokamak devices, however, significant uncertainty remains in accurately modeling detachment thresholds, and in how detachment depends on divertor geometry. Whereas it was originally planned to perform dedicated divertor experiments on the National Spherical Tokamak Upgrade to address critical detachment and divertor geometry questions for this milestone, the experiments were deferred due to technical difficulties. Instead, existing NSTX divertor data was summarized and re-analyzed where applicable, and additional simulations were performed.

Homogeneous production and removal of NO/sub x/ from combustion exhaust gases. Fifth quarterly technical summary report, September 1-November 30, 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Silver, J.A.; Gozewski, C.M.; Kilb, C.E.

1979-12-01

The rate constant for the reaction of NH/sub 2/ + NO has been measured over the temperature range of 294 to 1200/sup 0/K. It exhibits a decrease in value with increasing temperatures. An upper limit to the rate of reaction of NH/sub 3/ + NO ..-->.. NH/sub 2/ + HNO is also reported. The hydroxyl radical has been identified as one of the products of the NH/sub 2/ + NO reaction, and the implications of this upon the modeling is discussed.

Combined Quarterly Technical Report Number 23. SATNET Development and Operation. Pluribus Satellite IMP Development. Remote Site Maintenance. Internet Operations and Maintenance. Mobile Access Terminal Network. TCP for the HP3000. TCP-TAC. TCP for VAX-UNIX

DTIC Science & Technology

1981-11-01

evaluate and test these ideas in the Internet research context. 4. Field third-generation gateways. At this point in time, we purposely avoid selecting a...plan to cover the period from now until the time when a gateway system can be fielded which implements the results of the current work in the Internet ... research community. The current gateway system is inadequate from both a functionality and a• performance standpoint, and therefore the transition

Spectrally-broad coherent anti-Stokes Raman scattering hyper-microscopy utilizing a Stokes supercontinuum pumped at 800 nm

PubMed Central

Porquez, Jeremy G.; Cole, Ryan A.; Tabarangao, Joel T.; Slepkov, Aaron D.

2016-01-01

We demonstrate spectral-focusing based coherent anti-Stokes Raman scattering (SF-CARS) hyper-microscopy capable of probing vibrational frequencies from 630 cm−1 to 3250 cm−1 using a single Ti:Sapphire femtosecond laser operating at 800 nm, and a commercially-available supercontinuum-generating fibre module. A broad Stokes supercontinuum with significant spectral power at wavelengths between 800 nm and 940 nm is generated by power tuning the fibre module using atypically long and/or chirped ~200 fs pump pulses, allowing convenient access to lower vibrational frequencies in the fingerprint spectral region. This work significantly reduces the instrumental and technical requirements for multimodal CARS microscopy, while expanding the spectral capabilities of an established approach to SF-CARS. PMID:27867735

Technical Advisory Team (TAT) report on the rocket sled test accident of October 9, 2008.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stofleth, Jerome H.; Dinallo, Michael Anthony; Medina, Anthony J.

2009-01-01

This report summarizes probable causes and contributing factors that led to a rocket motor initiating prematurely while employees were preparing instrumentation for an AIII rocket sled test at SNL/NM, resulting in a Type-B Accident. Originally prepared by the Technical Advisory Team that provided technical assistance to the NNSA's Accident Investigation Board, the report includes analyses of several proposed causes and concludes that the most probable source of power for premature initiation of the rocket motor was the independent battery contained in the HiCap recorder package. The report includes data, evidence, and proposed scenarios to substantiate the analyses.

Ultra-narrow-linewidth erbium-doped lasers on a silicon photonics platform

NASA Astrophysics Data System (ADS)

Li, Nanxi; Purnawirman, Purnawirman; Magden, E. Salih; Singh, Gurpreet; Singh, Neetesh; Baldycheva, Anna; Hosseini, Ehsan S.; Sun, Jie; Moresco, Michele; Adam, Thomas N.; Leake, Gerald; Coolbaugh, Douglas; Bradley, Jonathan D. B.; Watts, Michael R.

2018-02-01

We report ultra-narrow-linewidth erbium-doped aluminum oxide (Al2O3:Er3+) distributed feedback (DFB) lasers with a wavelength-insensitive silicon-compatible waveguide design. The waveguide consists of five silicon nitride (SiNx) segments buried under silicon dioxide (SiO2) with a layer Al2O3:Er3+ deposited on top. This design has a high confinement factor (> 85%) and a near perfect (> 98%) intensity overlap for an octave-spanning range across near infrared wavelengths (950-2000 nm). We compare the performance of DFB lasers in discrete quarter phase shifted (QPS) cavity and distributed phase shifted (DPS) cavity. Using QPS-DFB configuration, we obtain maximum output powers of 0.41 mW, 0.76 mW, and 0.47 mW at widely spaced wavelengths within both the C and L bands of the erbium gain spectrum (1536 nm, 1566 nm, and 1596 nm). In a DPS cavity, we achieve an order of magnitude improvement in maximum output power (5.43 mW) and a side mode suppression ratio (SMSR) of > 59.4 dB at an emission wavelength of 1565 nm. We observe an ultra-narrow linewidth of ΔνDPS = 5.3 +/- 0.3 kHz for the DPS-DFB laser, as compared to ΔγQPS = 30.4 +/- 1.1 kHz for the QPS-DFB laser, measured by a recirculating self-heterodyne delayed interferometer (RSHDI). Even narrower linewidth can be achieved by mechanical stabilization of the setup, increasing the pump absorption efficiency, increasing the output power, or enhancing the cavity Q.

Ultraviolet Thomson Scattering from Direct-Drive Coronal Plasmas in Multilayer Targets

NASA Astrophysics Data System (ADS)

Henchen, R. J.; Goncharov, V. N.; Michel, D. T.; Follett, R. K.; Katz, J.; Froula, D. H.

2014-10-01

Ultraviolet (λ4 ω = 263 nm) Thomson scattering (TS) was used to probe ion-acoustic waves (IAW's) and electron plasma waves (EPW's) from direct-drive coronal plasmas. Fifty-nine drive beams (λ3 ω = 351 nm) illuminate a spherical target with a radius of ~ 860 μ m. A series of experiments studied the effect of higher electron temperature near the 3 ω quarter-critical surface (~ 2 . 5 ×1021 cm-3) on laser-plasma interactions resulting from a Si layer in the target. Electron temperatures and densities were measured from 150 to 400 μm from the initial target surface. Standard CH shells were compared to two-layered shells of CH and Si and three-layered shells of CH, Si, and CH. These multilayer targets have less hot-electron energy than standard CH shells as a result of higher electron temperature in the coronal plasmas. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Groundbased investigation of comet 67p/churyumov- gerasimenko, target of the spacecraft Mission Rosetta

NASA Astrophysics Data System (ADS)

de Almeida, A. A.; Trevisan Sanzovo, D.; Sanzovo, G. C.; Boczko, R.; Miguel Torres, R.

In this work, we make a comparative study of Comet 67P/Churyumov-Gerasimenko, target of Mission Rosetta, with Comets 1P/Halley and Hyakutake(C/1996 B2). Water and gas) release rates are derived from visual magnitudes (mv), determined mostly by amateur astronomers, and listed in several issues of International Comet Quarterly(ICQ). We make a systematic and uniform analysis of continuum fluxes obtained at visual wavelengths and, using the framework of photometric theory of Newburn & Spinrad (1985, 1989), we estimate dust release rates, qd (in g/s), effective particle sizes, a (in micron), and dust-to-gas mass ratios, for this important sample of comets. We also determine the color excess of the dust particles, CE, relative to the Sun at wavelength ranges 477.0-524.0 nm in the 1996 return of Comet 67P/Churyumov-Gerasimenko, and 365.0-484.5 nm for Comets 1P/Halley and C/1996 B2.

EUV polarimetry for thin film and surface characterization and EUV phase retarder reflector development.

PubMed

Gaballah, A E H; Nicolosi, P; Ahmed, Nadeem; Jimenez, K; Pettinari, G; Gerardino, A; Zuppella, P

2018-01-01

The knowledge and the manipulation of light polarization state in the vacuum ultraviolet and extreme ultraviolet (EUV) spectral regions play a crucial role from materials science analysis to optical component improvements. In this paper, we present an EUV spectroscopic ellipsometer facility for polarimetry in the 90-160 nm spectral range. A single layer aluminum mirror to be used as a quarter wave retarder has been fully characterized by deriving the optical and structural properties from the amplitude component and phase difference δ measurements. The system can be suitable to investigate the properties of thin films and optical coatings and optics in the EUV region.

Liquid crystal modulator with ultra-wide dynamic range and adjustable driving voltage.

PubMed

Wang, Xing-jun; Huang, Zhang-di; Feng, Jing; Chen, Xiang-fei; Liang, Xiao; Lu, Yan-qing

2008-08-18

We demonstrated a reflective-type liquid crystal (LC) intensity modulator in 1550 nm telecomm band. An effective way to compensate the residual phase of a LC cell is proposed. With the adjustment of a true zero-order quarter wave plate and enhanced by total internal reflection induced birefringence, over 53 dB dynamic range was achieved, which is much desired for some high-end optical communication, infrared scene projection applications. In addition, the driving voltages were decreased and adjustable. Mechanical and spectral tolerance measurements show that our LC modulator is quite stable. Further applications of our experimental setup were discussed including bio-sensors and high speed modulators.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Looney, J.H.; Im, C.J.

The following report presents the technical progress achieved during the first quarter. The completion of this contract entails engineering evaluation in conjunction with basic laboratory research to determine overall process improvements, associated cost savings and the effect of these savings on product price as they relate to the UCC Physical Beneficiation Process for coal-water slurry manufacture. The technical effort for this quarter has concentrated on two basic areas of concern as they relate to the above-mentioned process. First, an engineering evaluation was carried out to examine the critical areas of improvement in the existing UCC Research Corporation single-stage cleaning circuitmore » (coarse coal, heavy media washer). When the plant runs for low ash coal product, at the specific gravity near 1.30, it was found that substantial product contamination resulted from magnetite carry over in the clean coal product. The reduction of the magnetite contamination would entail the application of more spray water to the clean coal drain and rinse screen, and the refinement of the existing dilute media handling system, to accept the increased quality of rinse water. It was also determined that a basic mechanical overhaul is needed on the washbox to ensure dependable operation during the future production of low-ash coal. The various cost elements involved with this renovation were determined by UCC personnel in the operational division. The second area of investigation was concerned with the laboratory evaluation of three separate source coals obtained from United Coal Company (UCC) and nearby mines to determine probable cleanability when using each seam of coal as a feed in the existing beneficiation process. Washability analyses were performed on each sample utilizing a specific gravity range from 1.25 to 1.50. 4 figures, 3 tables.« less

Studies of the DOM aqueous extracts from coastal marine sediments

NASA Astrophysics Data System (ADS)

Sakellariadou, F.

2012-04-01

Dissolved organic matter (DOM) represents a major exchangeable organic pool playing an outstanding role in the ocean carbon cycle. It has a complex chemical structure made up of a wide range of organic molecules. The composition of DOM depends on the sources proximity and the exposure to any sort of degradation mechanism. The coloured (or chromophoric) dissolved organic matter (CDOM), representing the optically active fraction of DOM, consists of aromatic rings able to absorb light in the visible and UV regions (Kirk, 1994) and fluorophoric molecules that emit light. The main fluorophoric moieties of CDOM are humic material with a blue fluorescence and protein material with an ultraviolet (UV) fluorescence (Mopper and Schultz, 1993). Dissolved organic matter interacts with pollutants either by enhancing their bioavailability or by influencing their transportation to the soluble phase. In addition, DOM affects the remineralisation of carbon and its preservation in marine sediments. Referring to its origin, it can be terrestrial, freshwater or marine one. Fluorescence spectroscopy is a technique widely applied for the identification and characterization of organic matter, being fast, simple, non-destructive and sensitive. In addition, the fluorescence analysis for the physico-chemical characterization of organic matter requires a small amount of aqueous sample at a low concentration, in comparison with the large sample volumes needed for conventional techniques. At the present study coastal sediment samples were collected from Messiniakos gulf in the south western Peloponnese in South Greece. Messiniakos gulf has a seabed dominated by very abrupt inclinations reaching depths of more than 1000m. All samples, according to their grain size, are classified as fine clayey silt. Dissolved organic matter was extracted under gentle extraction conditions (4 mM CaCl2 solution). The various classes of organic components present at the DOM aqueous extracts were characterised by fluorescence spectroscopy technique as DOM fluorescence is a property furnishing valuable information for its composition and biogeochemical cycling. Fluorescence spectra were recorded using a Perkin-Elmer LS 55 luminescence spectrophotometer equipped with the WinLab 4.00.02 software for data processing. Conventional mono-dimensional emission, excitation and synchronous-scan excitation spectra were recorded. Mono dimensional emission spectra were recorded over the range 380-600 nm at a constant excitation wavelength of 360 nm. Excitation spectra were recorded over the range 300-500 nm at a fixed emission wavelength of 520 nm. Synchronous-scan excitation spectra were measured by scanning simultaneously both the excitation and the emission wavelengths (from 300 to 550 nm), while maintaining a constant, optimised wavelength difference Δλ (λem - λexc) = 18 nm. (Senesi et al., 1991). Total Luminescence Spectra (3D fluorescence spectra) were obtained in the form of excitation/emission matrix spectra (or contour maps) by scanning the wavelength emission over the range 300 to 600 nm, while the excitation wavelength was increased sequentially by 5-nm steps from 250 to 500 nm. In comparison with the limited provided information from the conventional fluorescence spectroscopy, EEM analysis seems to be sufficiently sensitive to distinguish between the various types of marine gelbstoff as well as to help estimating the contribution of each of them. Humification indices according to Ohno (2002) and Zsolnay (1999) were calculated. The Humification index (HIX) according to Ohno is calculated by dividing the emission intensity in the 435 to 480 nm region by the emission intensity in the 300 to 345 nm region; HIX quantifies the red shift of the emission spectra toward longer wavelengths with increasing humification. The HI index according to Zsolnay is defined as the area in the upper quarter (Σ435-480nm) of the usable emission peak divided by the area in the lower usable quarter (Σ300-445nm). All fluorescence spectra were thoroughly evaluated for the classification of chromophoric units present. Variations were observed according to the sampling site and more precisely its proximity to the coastline and the corresponding water column's depth; the oceanographic characteristics allowing or obstructing sea water circulation; as well as the proximity of each sample to the seabed, in other words the characterization of each sediment sample as surface of subsurface one.

Dependability of technical items: Problems of standardization

NASA Astrophysics Data System (ADS)

Fedotova, G. A.; Voropai, N. I.; Kovalev, G. F.

2016-12-01

This paper is concerned with problems blown up in the development of a new version of the Interstate Standard GOST 27.002 "Industrial product dependability. Terms and definitions". This Standard covers a wide range of technical items and is used in numerous regulations, specifications, standard and technical documentation. A currently available State Standard GOST 27.002-89 was introduced in 1990. Its development involved a participation of scientists and experts from different technical areas, its draft was debated in different audiences and constantly refined, so it was a high quality document. However, after 25 years of its application it's become necessary to develop a new version of the Standard that would reflect the current understanding of industrial dependability, accounting for the changes taking place in Russia in the production, management and development of various technical systems and facilities. The development of a new version of the Standard makes it possible to generalize on a terminological level the knowledge and experience in the area of reliability of technical items, accumulated over a quarter of the century in different industries and reliability research schools, to account for domestic and foreign experience of standardization. Working on the new version of the Standard, we have faced a number of issues and problems on harmonization with the International Standard IEC 60500-192, caused first of all by different approaches to the use of terms and differences in the mentalities of experts from different countries. The paper focuses on the problems related to the chapter "Maintenance, restoration and repair", which caused difficulties for the developers to harmonize term definitions both with experts and the International Standard, which is mainly related to differences between the Russian concept and practice of maintenance and repair and foreign ones.

Computational mechanics research and support for aerodynamics and hydraulics at TFHRC. Quarterly report January through March 2011. Year 1 Quarter 2 progress report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lottes, S. A.; Kulak, R. F.; Bojanowski, C.

2011-05-19

This project was established with a new interagency agreement between the Department of Energy and the Department of Transportation to provide collaborative research, development, and benchmarking of advanced three-dimensional computational mechanics analysis methods to the aerodynamics and hydraulics laboratories at the Turner-Fairbank Highway Research Center for a period of five years, beginning in October 2010. The analysis methods employ well-benchmarked and supported commercial computational mechanics software. Computational mechanics encompasses the areas of Computational Fluid Dynamics (CFD), Computational Wind Engineering (CWE), Computational Structural Mechanics (CSM), and Computational Multiphysics Mechanics (CMM) applied in Fluid-Structure Interaction (FSI) problems. The major areas of focusmore » of the project are wind and water loads on bridges - superstructure, deck, cables, and substructure (including soil), primarily during storms and flood events - and the risks that these loads pose to structural failure. For flood events at bridges, another major focus of the work is assessment of the risk to bridges caused by scour of stream and riverbed material away from the foundations of a bridge. Other areas of current research include modeling of flow through culverts to assess them for fish passage, modeling of the salt spray transport into bridge girders to address suitability of using weathering steel in bridges, vehicle stability under high wind loading, and the use of electromagnetic shock absorbers to improve vehicle stability under high wind conditions. This quarterly report documents technical progress on the project tasks for the period of January through March 2011.« less

Semen donors in New Zealand: their characteristics and attitudes.

PubMed

Daniels, K R

1987-08-01

The characteristics and attitudes of 37 semen donors in six New Zealand AID programmes are reported. Donors were found to be highly educated and, as a result, in predominantly professional and technical fields. The major reason for being a donor was altruism--a desire to help infertile couples, although financial considerations were a factor for almost one-quarter of the respondents. The attitude of donors towards payment differs markedly from the attitudes of specialists providing AID services. Personal knowledge of infertile couples was found to be a factor leading one-quarter of the donors to offer their services. There is a wide variation in the number of times that some donors are asked to donate, with some specialists operating outside the guidelines produced by the Royal New Zealand College of Obstetricians and Gynaecologists. Donors are almost equally divided on the issue of the child's right to know of the nature of her/his conception. Almost one-quarter of donors would still donate if there was a possibility that they could be traced in the future and a further 30% were unsure. These findings challenge some of the traditionally accepted views about the need for donor anonymity. It was found that 39% of donors expressed an interest in knowing the outcome of their donations. The results of the study have implications for policy and practice issues associated with the psychosocial aspects of AID. One implication is that it seems important that the psychosocial needs of donors be considered and that programmes should be flexible in responding to the differing attitudes, expectations, and needs of donors.

Investigation of mineral transformations and ash deposition during staged combustion. Quarterly technical progress report, April 1, 1997--June 30, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harb, J.N.

This report describes work performed in the fifteenth quarter of a fundamental study to examine the effect of staged combustion on ash formation and deposition. Efforts this quarter included addition of a new cyclone for improved particle sampling and modification of the existing sampling probe. Particulate samples were collected under a variety of experimental conditions for both coals under investigation. Deposits formed from the Black Thunder coal were also collected. Particle size and composition from the Pittsburgh No. 8 ash samples support previously reported results. In addition, the authors ability to distinguish char/ash associations has been refined and applied tomore » a variety of ash samples from this coal. The results show a clear difference between the behavior of included and excluded pyrite, and provide insight into the extent of pyrite oxidation. Ash samples from the Black Thunder coal have also been collected and analyzed. Results indicate a significant difference in the particle size of {open_quotes}unclassifiable{close_quotes} particles for ash formed during staged combustion. A difference in composition also appears to be present and is currently under investigation. Finally, deposits were collected under staged conditions for the Black Thunder coal. Specifically, two deposits were formed under similar conditions and allowed to mature under either reducing or oxidizing conditions in natural gas. Differences between the samples due to curing were noted. In addition, both deposits showed skeletal ash structures which resulted from in-situ burnout of the char after deposition.« less

UV lifetime demonstrator for space-based applications

NASA Astrophysics Data System (ADS)

Albert, Michael; Puffenburger, Kent; Schum, Tom; Fitzpatrick, Fran; Litvinovitch, Slava; Jones, Darrell; Rudd, Joseph; Hovis, Floyd

2016-05-01

A long-lived UV laser is an enabling technology for a number of high-priority, space-based lidar instruments. These include next generation cloud and aerosol lidars that incorporates a UV channel, direct detection 3-D wind lidars, and ozone DIAL (differential absorption lidar) systems. In previous SBIR funded work we developed techniques for increasing the survivability of components in high power UV lasers and demonstrated improved operational lifetimes. In this Phase III ESTO funded effort we are designing and building a TRL (Technology Readiness Level) 6 demonstrator that will have increased output power and a space-qualifiable package that is mechanically robust and thermally-stable. For full space compatibility, thermal control will be through pure conductive cooling. Contamination control processes and optical coatings will be chosen that are compatible with lifetimes in excess of 1 billion shots. The 1064nm output will be frequency tripled to provide greater than 100 mJ pulses of 355 nm light at 150 Hz. The laser module build was completed in the third quarter of 2015 at which time a series of life tests were initiated. The first phase of the lifetime testing is a 532 nm only test that is expected to complete in April 2016. The 532 nm lifetest will be followed by a 4 month half power UV life test and then a four month full power UV life test. The lifetime tests will be followed by thermal/vacuum (TVAC) and vibration testing to demonstrate that the laser optics module design is at TRL 6.

Bandwidth Dependence of Laser Plasma Instabilities Driven by the Nike KrF Laser

NASA Astrophysics Data System (ADS)

Weaver, J. L.; Oh, J.; Seely, J.; Kehne, D.; Brown, C. M.; Obenschain, S.; Serlin, V.; Schmitt, A. J.; Phillips, L.; Lehmberg, R. H.; McLean, E.; Manka, C.; Feldman, U.

2011-10-01

The Nike krypton-fluoride (KrF) laser at the Naval Research Laboratory operates in the deep UV (248 nm) and employs beam smoothing by induced spatial incoherence (ISI). In the first ISI studies at longer wavelengths (1054 nm and 527 nm) [Obenschain, PRL 62, 768(1989);Mostovych, PRL, 59, 1193(1987); Peyser, Phys. Fluids B 3, 1479(1991)], stimulated Raman scattering, stimulated Brillouin scattering, and the two plasmon decay instability were reduced when wide bandwidth ISI (δν / ν ~ 0.03-0.19%) pulses irradiated targets at moderate to high intensities (1014-1015W/cm2) . Recent Nike work showed that the threshold for quarter critical instabilities increased with the expected wavelength scaling, without accounting for the large bandwidth (δν ~ 1-3 THz). New experiments will compare laser plasma instabilities (LPI) driven by narrower bandwidth pulses to those observed with the standard operation. The bandwidth of KrF lasers can be reduced by adding narrow filters (etalons or gratings) in the initial stages of the laser. This talk will discuss the method used to narrow the output spectrum of Nike, the laser performance for this new operating mode, and target observations of LPI in planar CH targets. Work supported by DoE/NNSA.

Minimally invasive colorectal surgery: status and technical specifications.

PubMed

Keller, D S; Ibarra, S; Haas, E M

2015-10-01

Laparoscopy was the most significant technologic advance in colorectal surgery in the last quarter century. The safety, feasibility and oncologic equivalence have been proven, and undisputed clinical benefits have also been demonstrated over open approaches. Despite proven benefits, laparoscopic has not dominated the market, especially for colon and rectal cancer cases. Adaptations in laparoscopic technique were developed to increase use of minimally invasive surgery. Concurrently, there has been a paradigm shift toward less invasive technologies to further optimize patient outcomes. From these needs, hand assisted laparoscopic surgery (HALS), single incision laparoscopic surgery (SILS), and robotic assisted laparoscopic surgery (RALS) were applied to colorectal surgery. Each platform has unique costs and benefits, and similar outcomes when likened to each other in comparative studies. However, conventional laparoscopy, HALS, SILS, and RALS actually serve a complementary role as tools to increase the use of minimally invasive colorectal surgery. The goal of this paper is to review the history, current status, technical specifications, and evolution of the major minimally invasive platforms for colorectal surgery.

Technical Aspects of Acoustical Engineering for the ISS [International Space Station

NASA Technical Reports Server (NTRS)

Allen, Christopher S.

2009-01-01

It is important to control acoustic levels on manned space flight vehicles and habitats to protect crew-hearing, allow for voice communications, and to ensure a healthy and habitable environment in which to work and live. For the International Space Station (ISS) this is critical because of the long duration crew-stays of approximately 6-months. NASA and the JSC Acoustics Office set acoustic requirements that must be met for hardware to be certified for flight. Modules must meet the NC-50 requirement and other component hardware are given smaller allocations to meet. In order to meet these requirements many aspects of noise generation and control must be considered. This presentation has been developed to give an insight into the various technical activities performed at JSC to ensure that a suitable acoustic environment is provided for the ISS crew. Examples discussed include fan noise, acoustic flight material development, on-orbit acoustic monitoring, and a specific hardware development and acoustical design case, the ISS Crew Quarters.

Water quality and biological conditions in Wheeler Reservoir during operation of Browns Ferry Nuclear Plant (Unit 1 and 2), January 1, 1975-June 30, 1975

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1975-08-05

This report covers the fourth semiannual report period of operation of Browns Ferry Nuclear Plant, which extends from January 1, 1975 to June 30, 1975. Quarterly monitoring periods of the calender year are defined as follows: First - January 1 through March 31 (Winter), Second - April 1 through June 30 (Spring), Third - July 1 through September 30 (Summer), Fourth - October 1 through December 31 (Fall). Figure 1 shows the locations of the various environmental monitoring stations at the Browns Ferry Nuclear Plant. This report is submitted in conformance with section 5.6.1 of the Environmental Technical Specifications formore » the Browns Ferry Nuclear Plant, June 1973. Several revisions in the Technical Specifications have been submitted by TVA and approved by NRC (formerly AEC) since June 1973. This report is based upon the revisions, approved through the end of this reporting period (June 30, 1975).« less

Publications of the Jet Propulsion Laboratory, 1992

NASA Technical Reports Server (NTRS)

1994-01-01

JPL Bibliography 39-33 describes and indexes by primary author the externally distributed technical reporting, released during calendar year 1992, that resulted from scientific and engineering work performed or managed by the Jet Propulsion Laboratory. Three classes of publications are included: (1) JPL Publication (92-series) in which the information is complete for a specific accomplishment; (2) articles from the quarterly Telecommunications and Data Acquisition (TDA) Progress Report (42-series) (each collection of articles in this class of publication presents a periodic survey of current accomplishments by the Deep Space Network as well as other developments in Earth-based radio technology); and (3) articles published in the open literature.

Medical school libraries in the United States and Canada built between 1961 and 1971.

PubMed Central

Beatty, W K; Beatty, V L

1975-01-01

Twenty-four medical school libraries in the United States and Canada built between 1961 and 1971 were surveyed by means of questionnaires and visits. Results indicated that half of these libraries will have reached maximum functional capacity approximately six years after they moved into their new quarters. Space for technical processing is generally much less than required. Special features and examples of effective planning are described, and problems in arrangement, traffic patterns for people and materials, and the lack of logical expansion space are discussed. Comparisons are made with a similar survey of twenty medical school libraries made in 1961. Images PMID:1191825

Mountain research

NASA Astrophysics Data System (ADS)

The newly incorporated International Mountain Society (IMS) will in May begin publication of an interdisciplinary scientific journal, Mountain Research and Development. The quarterly will be copublished with the United National University; additional support will come from UNESCO.A primary objective of IMS is to ‘help solve mountain land-use problems by developing a foundation of scientific and technical knowledge on which to base management decisions,’ according to Jack D. Ives, president of the Boulder-based organization. ‘The Society is strongly committed to the belief that a rational worldwide approach to mountain problems must involve a wide range of disciplines in the natural and human sciences, medicine, architecture, engineering, and technology.’

Investigation of Test Methods, Material Properties, and Processes for Solar Cell Encapsulants

NASA Technical Reports Server (NTRS)

1979-01-01

During this quarter the technical activities were directed toward the reformulation of ethylene/vinyl acetate copolymer for use as a compound in solar cell module fabrication. Successful formulations were devised that lowered the temperature required for cure and raised the gel content. A major volatile component was also eliminated (acrylate crosslinking agent) which should aid in the production of bubble free laminates. Adhesive strengths and primers for the bonding of ethylene/vinyl acetate to supersyrate and substrate materials was assessed with encouraging results. The incorporation of silane compounds gave high bond strengths. A survey of scrim materials was also conducted.

Defects and Impurities in 4H- and 6H-SiC Homoepitaxial Layers: Identification, Origin, Effect on Properties of Ohmic Contacts and Insulating Layers and Reduction.

DTIC Science & Technology

1997-03-01

Grant #N00014-95-l-1080 Office of the Chief of Naval Research Report for the period 1/1/97-3/31/97 R. F. Davis, M. O. Aboelfotoh , B. J. Baliga*, R. J...Contacts and Insulating Layers and Reduction . AUTHOR(S) R. F. Davis, M. O. Aboelfotoh , B. J. Baliga and R. J. Nemanich 5. FUNDING NUMBERS ydl4951... Aboelfotoh , B. J. Baliga, R. J. Nemanich, M. C. Benjamin, S. W. King, M. L. O’Brien, L. S. Porter, S. Sridevan, and H. S. Tomozawa, Quarterly Technical

X-ray satellite

NASA Technical Reports Server (NTRS)

1985-01-01

The 3rd Quarter Status Report on DFVLR's ROSAT project confirms that with regard to technical performance and costs the project is on schedule. The valid schedule for engineering model and flight model completion on May 7, 1985 leads to a launch date on October 30, 1987. Progress in each department is compared to and explained with regard to the milestone plan. Continued problems with the gold damping of the FM-mirror system and contamination of the sterile rooms where the mirrors are stored have led to postponement of milestone 7. It is not yet completely clear to what extent all successive milestones will be affected by this factor.

Nanolipoprotein Particles (NLPs) as Versatile Vaccine Platforms for Co-delivery of Multiple Adjuvants with Subunit Antigens from Burkholderia spp. and F. tularensis - Technical Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fischer, N. O.

The goal of this proposal is to demonstrate that colocalization of protein subunit antigens and adjuvants on nanolipoprotein particles (NLPs) can increase the protective efficacy of subunit antigens from Burkholderia spp. and Francisella tularensis against an aerosol challenge. In the second quarter of the third year, LLNL finalized all immunological assessments of NLP vaccine formulations in the F344 model. Battelle has immunized rats with three unique NLP formulations by either intramuscular or intranasal administration. All inoculations have been completed, and protective efficacy against an aerosolized challenge will begin at the end of October, 2014.

THE DIALOGICAL SELF IN PSYCHOANALYSIS.

PubMed

Muller, Felipe

2016-10-01

This paper describes the shift that appears to be taking place in contemporary psychoanalysis, as reflected among intersubjective approaches, from a monological conception of the self to a dialogical one. The monological self emphasizes the separation between mind, body, and external world, focusing on the representational and descriptive/referential function of language. In contrast, the dialogical self emphasizes practices, the permeable nature of relationships between subjects, and the constitutive function of language. This paper attempts to explain the growing emphasis on the dialogical self, understood from a theoretical, metatheoretical, and technical point of view, using contemporary intersubjective approaches to illustrate this shift. © 2016 The Psychoanalytic Quarterly, Inc.

Non-critical phase-matching fourth harmonic generation of a 1053-nm laser in an ADP crystal

PubMed Central

Ji, Shaohua; Wang, Fang; Zhu, Lili; Xu, Xinguang; Wang, Zhengping; Sun, Xun

2013-01-01

In current inertial confinement fusion (ICF) facilities, KDP and DKDP crystals are the second harmonic generation (SHG) and third harmonic generation (THG) materials for the Nd:glass laser (1053 nm). Based on the trend for the development of short wavelengths for ICF driving lasers, technical solutions for fourth harmonic generation (FHG) will undoubtedly attract more and more attention. In this paper, the rapid growth of an ADP crystal and non-critical phase-matching (NCPM) FHG of a 1053-nm laser using an ADP crystal are reported. The NCPM temperature is 33.7°C. The conversion efficiency from 526 to 263 nm is 70%, and the angular acceptance range is 55.4 mrad; these results are superior to those for the DKDP crystals. This research has shown that ADP crystals will be a competitive candidate in future ICF facilities when the utilisation of high-energy, high-efficiency UV lasers at wavelengths shorter than the present 351 nm is of interest. PMID:23549389

Non-critical phase-matching fourth harmonic generation of a 1053-nm laser in an ADP crystal.

PubMed

Ji, Shaohua; Wang, Fang; Zhu, Lili; Xu, Xinguang; Wang, Zhengping; Sun, Xun

2013-01-01

In current inertial confinement fusion (ICF) facilities, KDP and DKDP crystals are the second harmonic generation (SHG) and third harmonic generation (THG) materials for the Nd:glass laser (1053 nm). Based on the trend for the development of short wavelengths for ICF driving lasers, technical solutions for fourth harmonic generation (FHG) will undoubtedly attract more and more attention. In this paper, the rapid growth of an ADP crystal and non-critical phase-matching (NCPM) FHG of a 1053-nm laser using an ADP crystal are reported. The NCPM temperature is 33.7°C. The conversion efficiency from 526 to 263 nm is 70%, and the angular acceptance range is 55.4 mrad; these results are superior to those for the DKDP crystals. This research has shown that ADP crystals will be a competitive candidate in future ICF facilities when the utilisation of high-energy, high-efficiency UV lasers at wavelengths shorter than the present 351 nm is of interest.

Research on solvent-refined coal. Quarterly technical progress report, April 1, 1981-June 30, 1981

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1981-10-01

This report describes progress on the Research on Solvent Refined Coal project by The Pittsburg and Midway Coal Mining Co.'s Merriam Laboratory during the second quarter of 1981. Alexander Mine coal was evaluated as a feedstock for major liquefaction facilities and had a yield structure similar to other reactive Pittsburgh seam coals at standard SRC II conditions. Two lots of coal from the Ireland Mine (Pittsburgh seam) were found to be of nearly the same composition and produced essentially the same yields. Two experiments in which coal-derived nonvolatile organic matter was processed without fresh coal feed indicate constant rates ofmore » conversion of SRC to oil and gas. Insoluble organic matter (IOM) remained unconverted. The naphtha and middle distillate products from the deep conversion contained less sulfur but more nitrogen than those from conventional SRC II processing. Encouraging results were obtained when a very small amount of iron oxide dispersed on alumina was added to Kaiparowits coal which cannot be processed at normal SRC II conditions without added catalyst. Subbituminous coals from the McKinley and Edna Mines were processed successfully with added pyrite but would not run when the added catalyst was removed.« less

Enthalpy measurement of coal-derived liquids. Technical progress report, November 1982-January 1983

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kidnay, A.J.; Yesavage, V.F.

The objective of this research is to measure the enthalpy for representative coal-derived liquids and model compounds over the pressure and temperature regions most likely to be encountered in both liquefaction and processing systems, and to prepare from the data an enthalpy correlation suitable for process design calculations. The correlational effort this past quarter on the enthalpy of coal-derived syncrudes and model compounds has emphasized the experimental determination of a correlating factor for association in coal liquids. As in previous work, the degree of association is to be related to cryoscopic molecular weight determinations on the coal liquids. To thismore » end, work on and an evaluationof a cryoscopic molecular weight apparatus was completed this quarter. Molecular weights of coal liquids determined by the standard Beckman freezing point depression apparatus were consistently low (5 to 10%). After modifications of the apparatus, it was tested with the following compounds: hexane, dodecane, m-xylene and naphthalene. Benzene was the solvent used. However, the molecular weight measurements were again consistently lower than the true values, and in many cases the experimental error was greater than that of the Beckman apparatus.« less

Sensor system development for the WSO-UV (World Space Observatory-Ultraviolet) space-based astronomical telescope

NASA Astrophysics Data System (ADS)

Hayes-Thakore, Chris; Spark, Stephen; Pool, Peter; Walker, Andrew; Clapp, Matthew; Waltham, Nick; Shugarov, Andrey

2015-10-01

As part of a strategy to provide increasingly complex systems to customers, e2v is currently developing the sensor solution for focal plane array for the WSO-UV (World Space Observatory - Ultraviolet) programme, a Russian led 170 cm space astronomical telescope. This is a fully integrated sensor system for the detection of UV light across 3 channels: 2 high resolution spectrometers covering wavelengths of 115 - 176 nm and 174 - 310 nm and a Long-Slit Spectrometer covering 115 nm - 310 nm. This paper will describe the systematic approach and technical solution that has been developed based on e2v's long heritage, CCD experience and expertise. It will show how this approach is consistent with the key performance requirements and the overall environment requirements that the delivered system will experience through ground test, integration, storage and flight.

High-resolution x-ray tomography using laboratory sources

NASA Astrophysics Data System (ADS)

Tkachuk, Andrei; Feser, Michael; Cui, Hongtao; Duewer, Fred; Chang, Hauyee; Yun, Wenbing

2006-08-01

X-ray computed tomography (XCT) is a powerful nondestructive 3D imaging technique, which enables the visualization of the three dimensional structure of complex, optically opaque samples. High resolution XCT using Fresnel zone plate lenses has been confined in the past to synchrotron radiation centers due to the need for a bright and intense source of x-rays. This confinement severely limits the availability and accessibility of x-ray microscopes and the wide proliferation of this methodology. We are describing a sub-50nm resolution XCT system operating at 8 keV in absorption and Zernike phase contrast mode based on a commercially available laboratory x-ray source. The system utilizes high-efficiency Fresnel zone plates with an outermost zone width of 35 nm and 700 nm structure height resulting in a current spatial resolution better than 50 nm. In addition to the technical description of the system and specifications, we present application examples in the semiconductor field.

The Assessment of Liver Reserve Function by Spectrophotometry based on Determination of Phenacetin and Paracetamol.

PubMed

Ren, Rui; Ma, Yongmei; Ma, Wanshan; Lu, Sumei

2015-01-01

To establish a technical system for assessing liver reserve function based on spectrophotometry by detection of phenacetin and paracetamol in blood samples. Taking detected contents of phenacetin and paracetamol by high performance liquid chromatography (HPLC) as standard, which was proved to be able to detect drug concentrations with high resolution and accuracy, we established a technical system based on the spectrophotometric technique to assay phenacetin and paracetamol, including the color system, the maximum absorption wavelength, the influence factors of color system, and the optimal conditions for hydrolysis. Then we verified our established system compared with that under HPLC by recovery test. This study established a technical system to detect phenacetin and paracetamol in blood samples using spectrophotometry. Mainly, 3 mol/L hydrochloric acid (HCl) was added to samples for hydrolysis for 30 minutes, then, adding 0.02% 1,2-naphthoquinone-4-sulfonate (NQS), 1% cetyltrimethyl ammonium bromide (CTA) and 2% sodium hydroxide (or 3% sodium carbonate) (ratio of 1:6:1:2 or 3), and the absorbance was measured at 500 nm and 570 nm to calculate their concentrations. Using an established spectrophotometric system to detect phenacetin and paracetamol in blood samples could assess liver reserve function, which was proved comparable with HPLC in resolution and repeatability.

77 FR 8926 - Board Meeting: March 7, 2012-Albuquerque, NM; The U.S. Nuclear Waste Technical Review Board Will...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-15

... Repository Geologies Pursuant to its authority under section 5051 of Public Law 100-203, the Nuclear Waste... repository. A representative of the U.S. Geological Survey (USGS) will provide a USGS perspective on this...

Dual-modulation fiber Fabry-Perot interferometer with double reflection for slowly-varying displacements.

PubMed

Seat, H C; Chawah, P; Cattoen, M; Sourice, A; Plantier, G; Boudin, F; Chéry, J; Brunet, C; Bernard, P; Suleiman, M

2012-07-15

This Letter describes a dual-amplitude modulation technique incorporated into a double reflection extrinsic-type fiber Fabry-Perot interferometer to measure periodic, nonperiodic as well as quasi-static displacements. The modulation scheme simultaneously maintains the interference signal pair in quadrature and provides a reference signal for displacements inferior to a quarter of the source wavelength. The control and phase demodulation of the interferometer carried out via software enable quasi-real-time measurement and facilitates sensor alignment. The sensor system can be exploited in the low frequency range from 10(-3) to ∼500 Hz and has a resolution better than 2.2 nm, targeting applications in geophysics.

Designs and performance of microprocessor-controlled knee joints.

PubMed

Thiele, Julius; Westebbe, Bettina; Bellmann, Malte; Kraft, Marc

2014-02-01

In this comparative study, three transfemoral amputee subjects were fitted with four different microprocessor-controlled exoprosthetic knee joints (MPK): C-Leg, Orion, Plié2.0, and Rel-K. In a motion analysis laboratory, objective gait measures were acquired during level walking at different velocities. Subsequent technical analyses, which involved X-ray computed tomography, identified the functional mechanisms of each device and enabled corroboration of the performance in the gait laboratory by the engineering design of the MPK. Gait measures showed that the mean increase of the maximum knee flexion angle at different walking velocities was closest in value to the unaffected contralateral knee (6.2°/m/s) with C-Leg (3.5°/m/s; Rel-K 17.0°/m/s, Orion 18.3°/m/s, and Plié2.0 28.1°/m/s). Technical analyses corroborated that only with Plié2.0 the flexion resistances were not regulated by microprocessor control at different walking velocities. The muscular effort for the initiation of the swing phase, measured by the minimum hip moment, was found to be lowest with C-Leg (-82.1±14.1 Nm; Rel-K -83.59±17.8 Nm, Orion -88.0±16.3 Nm, and Plié2.0 -91.6±16.5 Nm). Reaching the extension stop at the end of swing phase was reliably executed with both Plié2.0 and C-Leg. Abrupt terminal stance phase extension observed with Plié2.0 and Rel-K could be attributed to the absence of microprocessor control of extension resistance.

On-line milk spectrometry: analysis of bovine milk composition

NASA Astrophysics Data System (ADS)

Spitzer, Kyle; Kuennemeyer, Rainer; Woolford, Murray; Claycomb, Rod

2005-04-01

We present partial least squares (PLS) regressions to predict the composition of raw, unhomogenised milk using visible to near infrared spectroscopy. A total of 370 milk samples from individual quarters were collected and analysed on-line by two low cost spectrometers in the wavelength ranges 380-1100 nm and 900-1700 nm. Samples were collected from 22 Friesian, 17 Jersey, 2 Ayrshire and 3 Friesian-Jersey crossbred cows over a period of 7 consecutive days. Transmission spectra were recorded in an inline flowcell through a 0.5 mm thick milk sample. PLS models, where wavelength selection was performed using iterative PLS, were developed for fat, protein, lactose, and somatic cell content. The root mean square error of prediction (and correlation coefficient) for the nir and visible spectrometers respectively were 0.70%(0.93) and 0.91%(0.91) for fat, 0.65%(0.5) and 0.47%(0.79) for protein, 0.36%(0.49) and 0.45%(0.43) for lactose, and 0.50(0.54) and 0.48(0.51) for log10 somatic cells.

Fracture behavior of neutron-irradiated high-manganese austenitic steels

NASA Astrophysics Data System (ADS)

Yoshida, H.; Miyata, K.; Narui, M.; Kayano, H.

1991-03-01

The instrumented Charpy impact test was applied to study the fracture behavior of high-manganese austenitic steels before and after neutron irradiations. Quarter-size specimens of a commercial high-manganese steel (18% Mn-5% Ni-16% Cr), three reference steels (21% Mn-1% Ni-9% Cr, 20% Mn-1% Ni-11% Cr, 15% Mn-1% Ni-13% Cr) and two model steels (17% Mn-4.5% Si-6.5% Cr, 22% Mn-4.5% Si-6.5% Cr-0.2% N) were used for the impact tests at temperatures between 77 and 523 K. The load-deflection curves showed typical features corresponding to characteristics of the fracture properties. The temperature dependences of fracture energy and failure deflection obtained from the curves clearly demonstrate only small effects up to 2 × 10 23 n/m 2 ( E > 0.1 MeV) and brittleness at room temperature in 17% Mn-Si-Cr steel at 1.6 × 10 25 n/m 2 ( E > 0.1 MeV), while ductility still remains in 22%Mn-Si-Cr steel.

Tracheal anastomosis using indocyanine green dye enhanced fibrinogen with a near-infrared diode laser

NASA Astrophysics Data System (ADS)

Auteri, Joseph S.; Jeevanandam, Valluvan; Oz, Mehmet C.; Libutti, Steven K.; Kirby, Thomas J.; Smith, Craig R.; Treat, Michael R.

1990-06-01

A major obstacle to lung transplantation and combined heart- lung transplantation is dehiscence of the tracheobronchial anastomosis. We explored the possibility of laser welded anastomoses in canine tracheas in vivo. Laser anastomoses were performed on three-quarter circumferential anterior tracheotomies. A continous wave diode laser (808 +1 nm) at a power density of 9.6 watts/cm was used. Human fibrinogen was mixed with indocyanine green dye (ICG, max absorbance 805 nm) and applied to the anastomosis site prior to laser exposure. Animals were sacrificed at 0, 21 and 28 days post-operatively. At sacrifice weld bursting pressures were measured by raising intratracheal pressure using forced ventilation via an endotracheal tube. Sutured and laser welded anastomoses had similar bursting pressures, and exhibited satisfactory histologic evidence of healing. However, compared to polypropylene sutured controls, the laser welded anastomoses exhibited less peritracheal inflammatory reaction and showed visibly smoother luminal surfaces at 21 and 28 days post- operatively. Tracheal anastomosis using ICG dye enhanced fibrinogen combined with the near-infrared diode laser is a promising extension of the technology of laser tissue fusion and deserves further study.

OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gordon Tibbitts; Arnis Judzis

2002-04-01

This document details the progress to date on the OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE--A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING contract for the quarter starting January 2002 through March 2002. Accomplishments include the following: In accordance to Task 7.0 (D. No.2 Technical Publications) TerraTek, NETL, and the Industry Contributors successfully presented a paper detailing Phase 1 testing results at the February 2002 IADC/SPE Drilling Conference, a prestigious venue for presenting DOE and private sector drilling technology advances. The full reference is as follows: (1) IADC/SPE 74540 ''World's First Benchmarking of Drilling Mud Hammer Performance atmore » Depth Conditions'' authored by Gordon A. Tibbitts, TerraTek; Roy C. Long, US Department of Energy, Brian E. Miller, BP America, Inc.; Arnis Judzis, TerraTek; and Alan D. Black, TerraTek. Gordon Tibbitts, TerraTek, will presented the well-attended paper in February of 2002. The full text of the Mud Hammer paper was included in the last quarterly report. (2) The Phase 2 project planning meeting (Task 6) was held at ExxonMobil's Houston Greenspoint offices on February 22, 2002. In attendance were representatives from TerraTek, DOE, BP, ExxonMobil, PDVSA, Novatek, and SDS Digger Tools. (3) PDVSA has joined the advisory board to this DOE mud hammer project. PDVSA's commitment of cash and in-kind contributions were reported during the last quarter. (4) Strong Industry support remains for the DOE project. Both Andergauge and Smith Tools have expressed an interest in participating in the ''optimization'' phase of the program. The potential for increased testing with additional Industry cash support was discussed at the planning meeting in February 2002.« less

Delivering digital health and well-being at scale: lessons learned during the implementation of the dallas program in the United Kingdom

PubMed Central

Devlin, Alison M; McGee-Lennon, Marilyn; O’Donnell, Catherine A; Bouamrane, Matt-Mouley; Agbakoba, Ruth; O’Connor, Siobhan; Grieve, Eleanor; Finch, Tracy; Wyke, Sally; Watson, Nicholas; Browne, Susan

2016-01-01

Objective To identify implementation lessons from the United Kingdom Delivering Assisted Living Lifestyles at Scale (dallas) program—a large-scale, national technology program that aims to deliver a broad range of digital services and products to the public to promote health and well-being. Materials and Methods Prospective, longitudinal qualitative research study investigating implementation processes. Qualitative data collected includes semi-structured e-Health Implementation Toolkit–led interviews at baseline/mid-point (n = 38), quarterly evaluation, quarterly technical and barrier and solutions reports, observational logs, quarterly evaluation alignment interviews with project leads, observational data collected during meetings, and ethnographic data from dallas events (n > 200 distinct pieces of qualitative data). Data analysis was guided by Normalization Process Theory, a sociological theory that aids conceptualization of implementation issues in complex healthcare settings. Results Five key challenges were identified: 1) The challenge of establishing and maintaining large heterogeneous, multi-agency partnerships to deliver new models of healthcare; 2) The need for resilience in the face of barriers and set-backs including the backdrop of continually changing external environments; 3) The inherent tension between embracing innovative co-design and achieving delivery at pace and at scale; 4) The effects of branding and marketing issues in consumer healthcare settings; and 5) The challenge of interoperability and information governance, when commercial proprietary models are dominant. Conclusions The magnitude and ambition of the dallas program provides a unique opportunity to investigate the macro level implementation challenges faced when designing and delivering digital health and wellness services at scale. Flexibility, adaptability, and resilience are key implementation facilitators when shifting to new digitally enabled models of care. PMID:26254480

Delivering digital health and well-being at scale: lessons learned during the implementation of the dallas program in the United Kingdom.

PubMed

Devlin, Alison M; McGee-Lennon, Marilyn; O'Donnell, Catherine A; Bouamrane, Matt-Mouley; Agbakoba, Ruth; O'Connor, Siobhan; Grieve, Eleanor; Finch, Tracy; Wyke, Sally; Watson, Nicholas; Browne, Susan; Mair, Frances S

2016-01-01

To identify implementation lessons from the United Kingdom Delivering Assisted Living Lifestyles at Scale (dallas) program-a large-scale, national technology program that aims to deliver a broad range of digital services and products to the public to promote health and well-being. Prospective, longitudinal qualitative research study investigating implementation processes. Qualitative data collected includes semi-structured e-Health Implementation Toolkit-led interviews at baseline/mid-point (n = 38), quarterly evaluation, quarterly technical and barrier and solutions reports, observational logs, quarterly evaluation alignment interviews with project leads, observational data collected during meetings, and ethnographic data from dallas events (n > 200 distinct pieces of qualitative data). Data analysis was guided by Normalization Process Theory, a sociological theory that aids conceptualization of implementation issues in complex healthcare settings. Five key challenges were identified: 1) The challenge of establishing and maintaining large heterogeneous, multi-agency partnerships to deliver new models of healthcare; 2) The need for resilience in the face of barriers and set-backs including the backdrop of continually changing external environments; 3) The inherent tension between embracing innovative co-design and achieving delivery at pace and at scale; 4) The effects of branding and marketing issues in consumer healthcare settings; and 5) The challenge of interoperability and information governance, when commercial proprietary models are dominant. The magnitude and ambition of the dallas program provides a unique opportunity to investigate the macro level implementation challenges faced when designing and delivering digital health and wellness services at scale. Flexibility, adaptability, and resilience are key implementation facilitators when shifting to new digitally enabled models of care. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association.

Short Rotation Woody Crops Program. Quarterly progress report, March 1-May 31, 1985. [Sycamore, alders, black locust, larch, poplars, saltbush

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wright, L.L.; Perlack, R.D.; Wenzel, C.R.

1985-08-01

This report covers the progress of the Short Rotation Woody Crops Program (SRWCP) during the third quarter of fiscal year 1985. This report summarizes ORNL management activities, technical activities at ORNL and subcontract institutions, and the technology transfer that is occurring as a result of subcontractor and ORNL activities. Third-year results of a nutrient utilization study confirmed that there were no benefits to quarterly fertilization with urea nitrogen. Testing of one prototype short-rotation intensive culture harvester was conducted on a sycamore plantation on Scott Paper Company land in southern Alabama. Coppice yields of European black alder reported by Iowa Statemore » University indicate potential productivity of about 7.2 dry Mg . ha/sup -1/ . year/sup -1/ if the best trees are selected. Coppice yields were more than double first-rotation yields. About 31,000 black locust and larch trees were established in 12 genetic tests at 4 sites in Michigan. Seedling rotation productivity rates of 4-year-old hybrid poplar, based on harvest data, were reported by Pennsylvania State University. Rates varied from 4.8 dry Mg . ha/sup -1/ . year/sup -1/ to 10.7 dry Mg . ha/sup -1/ . year/sup -1/, depending on site, management strategy, and planting year. An efficient method for in vitro micropropagation of elite genotypes of fourwing saltbush was developed by Plant Resources Institute. A new study to evaluate yield/density relationships was established by the USDA Forest Service, Pacific Northwest Forest and Range Experiment Station. Dissertation research on the crown geometry of plantation-grown American sycamore was completed.« less

Particulate Hot Gas Stream Cleanup Technical Issues: Quarterly report, July 1-September 30, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pontius, D.H.

1996-12-09

This is the eighth in a series of quarterly reports describing the activities performed under Contract No. DE-AC21-94MC31160. Analyses of Hot Gas Stream Cleanup (HGCU) ashes and descriptions of filter performance address aspects of filter operation that are apparently linked to the characteristics of the collected ash or the performance of the ceramic barrier filter elements. Task 1 is designed to generate a data base of the key characteristics of ashes collected from operating advanced particle filters (APFS) and to relate these ash properties to the operation and performance of these filters. Task 2 concerns testing and failure analysis ofmore » ceramic filter elements. Under Task I during the past quarter, additional analyses were performed on ashes from the Ahlstrom 10 MWt Pressurized Fluidized Circulating Fluid Bed (PCFB) facility located at Karhula, Finland. Work continued on the HGCU data base being constructed in Microsoft Access. A variety of information has been entered into the data base, including numerical values, short or long text entries, and photographs. Detailed design of a bench top device for high temperature measurement of ash permeability has also begun. In addition to these activities, a paper was prepared and a poster was presented summarizing recent work performed under this contract at the 1996 DOE/METC Contractor`s Conference. A presentation was also given corresponding to the manuscript entitled Particle Characteristics and High-Temperature Filtration that was prepared for publication in the Proceedings of the Thirteenth Annual International Pittsburgh Coal Conference held this September in Pittsburgh, PA. Arrangements have been made to be present at the DOE/METC Modular Gas Cleanup Rig (MGCR) at the conclusion of the next run of the DOE/METC air blown Fluid Bed Gasifier (FBG). This visit will include on-site sampling to collect and characterize the filter cakes collected during FGB operation. Task 2 efforts during the past quarter focused on hoop tensile testing of Schumacher FT20 and Refractron 326 candle filter elements removed from the Karhula APF after 540 hours of service.« less

Bacterial meningitis epidemiology and return of Neisseria meningitidis serogroup A cases in Burkina Faso in the five years following MenAfriVac mass vaccination campaign.

PubMed

Diallo, Alpha Oumar; Soeters, Heidi M; Yameogo, Issaka; Sawadogo, Guetawendé; Aké, Flavien; Lingani, Clément; Wang, Xin; Bita, Andre; Fall, Amadou; Sangaré, Lassana; Ouédraogo-Traoré, Rasmata; Medah, Isaïe; Bicaba, Brice; Novak, Ryan T

2017-01-01

Historically, Neisseria meningitidis serogroup A (NmA) caused large meningitis epidemics in sub-Saharan Africa. In 2010, Burkina Faso became the first country to implement a national meningococcal serogroup A conjugate vaccine (MACV) campaign. We analyzed nationwide meningitis surveillance data from Burkina Faso for the 5 years following MACV introduction. We examined Burkina Faso's aggregate reporting and national laboratory-confirmed case-based meningitis surveillance data from 2011-2015. We calculated incidence (cases per 100,000 persons), and described reported NmA cases. In 2011-2015, Burkina Faso reported 20,389 cases of suspected meningitis. A quarter (4,503) of suspected meningitis cases with cerebrospinal fluid specimens were laboratory-confirmed as either S. pneumoniae (57%), N. meningitidis (40%), or H. influenzae (2%). Average adjusted annual national incidence of meningococcal meningitis was 3.8 (range: 2.0-10.2 annually) and was highest among infants aged <1 year (8.4). N. meningitidis serogroup W caused the majority (64%) of meningococcal meningitis among all age groups. Only six confirmed NmA cases were reported in 2011-2015. Five cases were in children who were too young (n = 2) or otherwise not vaccinated (n = 3) during the 2010 MACV mass vaccination campaign; one case had documented MACV receipt, representing the first documented MACV failure. Meningococcal meningitis incidence in Burkina Faso remains relatively low following MACV introduction. However, a substantial burden remains and NmA transmission has persisted. MACV integration into routine childhood immunization programs is essential to ensure continued protection.

A rapid excitation-emission matrix fluorometer utilizing supercontinuum white light and acousto-optic tunable filters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Wenbo; Department of Dermatology and Skin Science, University of British Columbia, 835 West 10th Avenue, Vancouver, British Columbia V5Z 4E8; Department of Biomedical Engineering, University of British Columbia, KAIS 5500, 2332 Main Mall, Vancouver, British Columbia V6T 1Z4

Scanning speed and coupling efficiency of excitation light to optic fibres are two major technical challenges that limit the potential of fluorescence excitation-emission matrix (EEM) spectrometer for on-line applications and in vivo studies. In this paper, a novel EEM system, utilizing a supercontinuum white light source and acousto-optic tunable filters (AOTFs), was introduced and evaluated. The supercontinuum white light, generated by pumping a nonlinear photonic crystal fiber with an 800 nm femtosecond laser, was efficiently coupled into a bifurcated optic fiber bundle. High speed EEM spectral scanning was achieved using AOTFs both for selecting excitation wavelength and scanning emission spectra.more » Using calibration lamps (neon and mercury argon), wavelength deviations were determined to vary from 0.18 nm to −0.70 nm within the spectral range of 500–850 nm. Spectral bandwidth for filtered excitation light broadened by twofold compared to that measured with monochromatic light between 650 nm and 750 nm. The EEM spectra for methanol solutions of laser dyes were successfully acquired with this rapid fluorometer using an integration time of 5 s.« less

Multi-Wave Station of Solar Monitoring

NASA Astrophysics Data System (ADS)

Korokhin, V.; Akimov, L.; Beletsky, S.; Belkina, I.; Velikodsky, Y.; Marchenko, G.; Shaparenko, E.

A technical description of the contemporary solar telescope of the Kharkov Astronomical Observatory (http://khassm.virtualave.net) is given, and the plan to future development is sketched. A wide range monitoring of solar activity including observations near UV range in Balmer continuum and the IR line of He 1083 nm is presented.

Effects of lunar phases on short-term, explosive physical performance among young trained athletes.

PubMed

Yousfi, Narimen; Mejri, Mohamed Arbi; Rouissi, Mehdi; Hammami, Amri; Tabben, Montassar; Chaouachi, Anis; Haddad, Monoem; Chamari, Karim

2018-04-01

Beliefs that lunar phases affect human physiology started in ancient times. Research has recently revealed that a physical fitness index increased in sedentary students at the new moon (NM) and full moon (FM) compared to other moon phases. However, the effect of lunar cycle (moon illumination and gravitational pull) on physical performance in athletes was not examined. Therefore, this study aimed to evaluate whether short-term explosive performance can be influenced by the different phases of the lunar cycle. Fourteen young male Taekwondo athletes (age: 16.9 ± 0.7 years, height: 159.7 ± 50.6 cm, body mass: 62.85 ± 7.84 kg) performed the following tests to assess the explosive physical performance during the different phases of the lunar cycle (NM, FQ (first quarter), FM, and LQ (last quarter)): maximal isometric manual contraction (dominant hand (MIMCD) and non-dominant hand (MIMCND)), maximal back isometric contraction (MBIC), squat jump (SJ), countermovement jump (CMJ), and 10-m sprint (10 m). The testing sessions during the different moon phases were performed in a counterbalanced order. The order of tests remained the same (MIMCD, MIMCND, MBIC, SJ, CMJ, and 10 m), and all sessions were performed in the evening (6:00 to 8:00 p.m.) on the first day of each evaluated lunar phase. Each parameter was measured over two consecutive lunar months in the calendar. Analysis of variance tests showed that there was no significant effect of lunar cycle on all explosive test measures, p > 0.05. Our results failed to identify any effect of lunar phase on evening explosive performance (mainly involving phosphagen pathway-based efforts) among young trained athletes. Therefore, it appears that moon phase/illumination does not affect short-term physical performance in young trained adolescents.

Optical properties of amorphous SiO2-TiO2 multi-nanolayered coatings for 1064-nm mirror technology

NASA Astrophysics Data System (ADS)

Magnozzi, M.; Terreni, S.; Anghinolfi, L.; Uttiya, S.; Carnasciali, M. M.; Gemme, G.; Neri, M.; Principe, M.; Pinto, I.; Kuo, L.-C.; Chao, S.; Canepa, M.

2018-01-01

The use of amorphous, SiO2-TiO2 nanolayered coatings has been proposed recently for the mirrors of 3rd-generation interferometric detectors of gravitational waves, to be operated at low temperature. Coatings with a high number of low-high index sub-units pairs with nanoscale thickness were found to preserve the amorphous structure for high annealing temperatures, a key factor to improve the mechanical quality of the mirrors. The optimization of mirror designs based on such coatings requires a detailed knowledge of the optical properties of sub-units at the nm-thick scale. To this aim we have performed a Spectroscopic Ellipsometry (SE) study of amorphous SiO2-TiO2 nanolayered films deposited on Si wafers by Ion Beam Sputtering (IBS). We have analyzed films that are composed of 5 and 19 nanolayers (NL5 and NL19 samples) and have total optical thickness nominally equivalent to a quarter of wavelength at 1064 nm. A set of reference optical properties for the constituent materials was obtained by the analysis of thicker SiO2 and TiO2 homogeneous films (∼ 120 nm) deposited by the same IBS facility. By flanking SE with ancillary techniques, such as TEM and AFM, we built optical models that allowed us to retrieve the broad-band (250-1700 nm) optical properties of the nanolayers in the NL5 and NL19 composite films. In the models which provided the best agreement between simulation and data, the thickness of each sub-unit was fitted within rather narrow bounds determined by the analysis of TEM measurements on witness samples. Regarding the NL5 sample, with thickness of 19.9 nm and 27.1 nm for SiO2 and TiO2 sub-units, respectively, the optical properties presented limited variations with respect to the thin film counterparts. For the NL19 sample, which is composed of ultrathin sub-units (4.4 nm and 8.4 nm for SiO2 and TiO2, respectively) we observed a significant decrease of the IR refraction index for both types of sub-units; this points to a lesser mass density with respect to the thin film reference. The results are discussed in the light of the existing literature on nanofilms of amorphous oxides.

Nm-scale spatial resolution x-ray imaging with MLL nanofocusing optics: instrumentational requirements and challenges

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nazaretski, E.; Yan, H.; Lauer, K.

2016-08-30

The Hard X-ray Nanoprobe (HXN) beamline at NSLS-II has been designed and constructed to enable imaging experiments with unprecedented spatial resolution and detection sensitivity. The HXN X-ray Microscope is a key instrument for the beamline, providing a suite of experimental capabilities which includes scanning fluorescence, diffraction, differential phase contrast and ptychography utilizing Multilayer Laue Lenses (MLL) and zoneplate (ZP) as nanofocusing optics. In this paper, we present technical requirements for the MLL-based scanning microscope, outline the development concept and present first ~15 x 15 nm 2 spatial resolution x-ray fluorescence images.

Automatic generation of reports at the TELECOM SCC

NASA Astrophysics Data System (ADS)

Beltan, Thierry; Jalbaud, Myriam; Fronton, Jean Francois

In-orbit satellite follow-up produces a certain amount of reports on a regular basis (daily, weekly, quarterly, annually). Most of these documents use the information of former issues with the increments of the last period of time. They are made up of text, tables, graphs or pictures. The system presented here is the SGMT (Systeme de Gestion de la Memoire Technique), which means Technical Memory Mangement System. It provides the system operators with tools to generate the greatest part of these reports, as automatically as possible. It gives an easy access to the reports and the large amount of available memory enables the user to consult data on the complete lifetime of a satellite family.

Enhanced oil recovery utilizing high-angle wells in the Frontier Formation, Badger Basin Field, Park County, Wyoming. Quarterly technical progress report, 1 January 1994--31 March 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fortmann, R.G.

1994-04-22

Sierra Energy Company, in consultation with Rim Companies, concluded that additional work was required for Subtask 2.1.4 -- Interpret data, of Task 2.1 - Acquire 3-D seismic data. The goal of this subtask was to interpret the 3-D seismic data, using a workstation, in order to locate the surface and subsurface positions for the slant and horizontal wellbores. Although this goal had been reached, more work was needed for plotting maps and seismic sections. Furthermore, it was determined that an additional look at the amplitude distribution in the Frontier sands would greatly benefit the interpretation.

Total Ore Processing Integration and Management

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leslie Gertsch; Richard Gertsch

2006-01-30

This report outlines the technical progress achieved for project DE-FC26-03NT41785 (Total Ore Processing Integration and Management) during the period 01 July through 30 September of 2005. This ninth quarterly report discusses the activities of the project team during the period 1 July through 30 September 2005. Richard Gertsch's unexpected death due to natural causes while in Minnesota to work on this project has temporarily slowed progress. Statistical analysis of the Minntac Mine data set for late 2004 is continuing. Preliminary results raised several questions that could be amenable to further study. Detailed geotechnical characterization is being applied to improve themore » predictability of mill and agglomerator performance at Hibtac Mine.« less

Publications of the Jet Propulsion Laboratory 1983

NASA Technical Reports Server (NTRS)

1984-01-01

The Jet propulsion Laboratory (JPL) bibliography describes and indexes by primary author the externally distributed technical reporting, released during calendar year 1983, that resulted from scientific and engineering work performed, or managed, by the Jet Propulsion Laboratory. Three classes of publications are included. JPL Publication (81-,82-,83-series, etc.), in which the information is complete for a specific accomplishment, articles published in the open literature, and articles from the quarterly telecommunications and Data Acquisition (TDA) Progress Report (42-series) are included. Each collection of articles in this class of publication presents a periodic survey of current accomplishments by the Deep Space Network as well as other developments in Earth-based radio technology.

Durability Testing of Commercial Ceramic Materials

NASA Technical Reports Server (NTRS)

Schienle, J. L.

1996-01-01

Technical efforts by AlliedSignal Engines in DOE/NASA-funded project from February, 1978 through December, 1995 are reported in the fields ceramic materials for gas turbine engines and cyclic thermal durability testing. A total of 29 materials were evaluated in 40 cyclic oxidation exposure durability tests. Ceramic test bars were cyclically thermally exposed to a hot combustion environment at temperatures up to 1371 C (2500 F) for periods of up to 3500 hours, simulating conditions typically encountered by hot flowpath components in an automotive gas turbine engine. Before and after exposure, quarter-point flexure strength tests were performed on the specimens, and fractography examinations including scanning electron microscopy (SEM) were performed to determine failure origins.

Combined Quarterly Technical Report Number 25. SATNET Development and Operation, Pluribus Satellite IMP Development, Remote Site Maintenance, Internet Operations and Maintenance, Mobile Access Terminal Network, TCP for the HP3000, TCP for VAX-UNIX.

DTIC Science & Technology

1982-05-01

the F-Bus. The two possible SuperSUE I Pollers, SSPE and SSPF, are on the E and F buses, respectively. P13 is the P13 Poller. A PSAT will have at... SSPE and SSPF are again the two possible SuperSUE Pollers. HPOL is an abbrevation for the HINPOL and HOUTPOL routines. -44- jReport No. 5003 Bolt...I IS I E-Bus,F-Bus I E-Bus Only I F-Bus only I s -- - - - - - - - - - - - - - - - - -- - - - - - P E-Bus ISMIE/ SSPE ISMIE/ SSPE ISMIF/SSPF IF-Bu3

Exploring high power, extreme wavelength operating potential of rare-earth-doped silica fiber

NASA Astrophysics Data System (ADS)

Zhou, Pu; Li, Ruixian; Xiao, Hu; Huang, Long; Zhang, Hanwei; Leng, Jinyong; Chen, Zilun; Xu, Jiangmin; Wu, Jian; Wang, Xiong

2017-08-01

Ytterbium-doped fiber laser (YDFL) and Thulium doped fiber laser (TDFL) have been two kinds of the most widely studied fiber laser in recent years. Although both silica-based Ytterbium-doped fiber and Thulium doped fiber have wide emission spectrum band (more than 200 nm and 400 nm, respectively), the operation spectrum region of previously demonstrated high power YDFL and TDFL fall into 1060-1100 nm and 1900-2050nm. Power scaling of YDFL and TDFL operates at short-wavelength or long-wavelength band, especially for extreme wavelength operation, although is highly required in a large variety of application fields, is quite challenging due to small net gain and strong amplified spontaneous emission (ASE). In this paper, we will present study on extreme wavelength operation of high power YDFL and TDFL in our group. Comprehensive mathematical models are built to investigate the feasibility of high power operation and propose effective technical methods to achieve high power operation. We have achieved (1) Diodepumped 1150nm long wavelength YDFL with 120-watt level output power (2) Diode-pumped 1178nm long wavelength YDFL operates at high temperature with 30-watt level output power (3) Random laser pumped 2153nm long wavelength TDFL with 20-watt level output power (4) Diode-pumped 1018nm short wavelength YDFL with a record 2 kilowatt output power is achieved by using home-made fiber combiner.

4. Northeast corner of quarters (executive officer's quarters), looking onto ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Northeast corner of quarters (executive officer's quarters), looking onto Quarter R (commanding officer's quarters), looking southeast - Naval Air Station Chase Field, Texas State Highway 202, 4.8 miles east of intersection of Texas State Highway 202 & U.S. State Highway 181, Beeville, Bee County, TX

Wide spectral range multiple orders and half-wave achromatic phase retarders fabricated from two lithium tantalite single crystal plates

NASA Astrophysics Data System (ADS)

Emam-Ismail, M.

2015-11-01

In a broad spectral range (300-2500 nm), we report the use of channeled spectra formed from the interference of polarized white light to extract the dispersion of the phase birefringence Δnp(λ) of the x- and y-cuts of lithium tantalite (LiTaO3:LT) plates. A new method named as wavenumber difference method is used to extract the spectral behavior of the phase birefringence of the x- and y- cuts of LT plates. The correctness of the obtained birefringence data is confirmed by using Jones vector method through recalculating the plates thicknesses. The spectral variation of the phase birefringence Δnp(λ) of the x- and y-cuts of LT plates is fitted to Cauchy dispersion function with relative error for both x- and y-cuts of order 2.4×10-4. The group birefringence dispersion Δng (λ) of the x- and y-cuts of LT plates is also calculated and fitted to Ghosh dispersion function with relative error for both x- and y-cuts of order 2.83×10-4. Furthermore, the phase retardation introduced by the x- and y-cuts of LT plates is also calculated. It is found that the amount of phase retardation confirms that the x- and y-cuts of LT plates can act as a multiple order half- and quarter-wave plates working at many different wavelengths through the spectral range 300-2500 nm. For the x- and y-cuts of LT plates, a large difference between group and phase birefringence is observed at a short wavelength (λ=300 nm); while such difference progressively diminished at longer wavelength (λ=2000 nm). In the near infrared region (NIR) region (700-2500 nm), a broad spectral full width at half maximum (FWHM) is observed for either x- or y-cut of LT plate which can act as if it is working as a zero order wave plate. Finally, an achromatic half-wave plate working at 598 nm and covering a wide spectral range (300-900 nm) is demonstrated experimentally by combining both x- and y-cuts of LT plates.

12 CFR 1777.10 - Developments prompting supervisory response.

Code of Federal Regulations, 2011 CFR

2011-01-01

...) An Enterprise's publicly reported net income for the most recent calendar quarter is less than one-half of its average quarterly net income for any four-quarter period during the prior eight quarters... than one-half of its average NIM for any four-quarter period during the prior eight quarters; (d) For...

Soldering mask laser removal from printed circuit boards aiming copper recycling.

PubMed

Raele, Marcus Paulo; De Pretto, Lucas Ramos; Zezell, Denise Maria

2017-10-01

Management of waste of electric and electronic equipment (WEEE) is a key issue for modern societies; furthermore, it contains valuable materials that can be recycled, especially in printed circuit boards (PCB), which have approximately one-third of their weight in copper. In this study we demonstrated the use of laser to strip the covering soldering mask on PCB's, thus exposing the copper underneath so that extraction techniques may take place. Using a Q-Switched Nd:YAG laser operating at 1064nm and 532nm we tested the procedure under different energy conditions. The laser stripping of the soldering mask was achieved with satisfactory results by irradiation with 225mJ at 1064nm. However, when using similar parameters at 532nm the process of the coating ejection was not promoted properly, leading to a faulty detachment. Infrared laser PCB stripping presents itself to be technically viable and environmental friendly, since it uses no chemicals inputs, offering one more option to WEEE treatment and recycling. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of a Rolling Process Design Tool for Use in Improving Hot Roll Slab Recovery (Quarterly Report: Q3-FY03)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Couch, R; Wang, P

2003-07-31

In this quarter, an FEM simulation has been performed to compare the shape of the deformed slab after the 8th reduction pass with the experimental metrology data provided by Alcoa Technical Center (ATC). Also, a bug in the thermal contact algorithm used in parallel processing have been identified and corrected for consistent thermal solutions between the rollers and the slab. The overall shape of the slab at the end of the 8th pass is shown in Figure 1. Comparison of the sectional views at the center plane along the length of the slab for both experiment and simulation, shows thatmore » the curvature at the slab mouth at the centerline is slightly higher than the experimental result as shown in Figure 2. We are currently focusing on tuning the parameter values used in the simulation and a more complete parametric study for validation is underway. Also, unexpected fracture occurred along the surface of the slab in the 9th pass as shown in Figure 3. We believe that the reason is due to previously noted inadequacies in the fracture model at low strain rates and high stress triaxiality. We are expecting to receive a modified fracture model based on additional experiment shortly from Alcoa.« less

Glancing-angle-deposited magnesium oxide films for high-fluence applications

DOE PAGES

Oliver, J. B.; Smith, C.; Spaulding, J.; ...

2016-06-15

Here, Birefringent magnesium oxide thin films are formed by glancing angle deposition to perform as quarter-wave plates at a wavelength of 351 nm. These films are being developed to fabricate a large aperture distributed-polarization rotator for use in vacuum, with an ultimate laser-damage–threshold goal of up to 12 J/cm 2 for a 5-ns flat-in-time pulse. The laser-damage threshold, ease of deposition, and optical film properties are evaluated. While the measured large-area laser-damage threshold is limited to ~4 J/cm 2 in vacuum, initial results based on small-spot testing in air (>20 J/cm 2) suggest MgO may be suitable with further processmore » development.« less

Circular polarization beam splitter that uses frustrated total internal reflection by an embedded symmetric achiral multilayer coating.

PubMed

Azzam, R M A; De, A

2003-03-01

A symmetric achiral trilayer structure, which consists of a high-index center layer sandwiched between two identical low-index films and embedded in a high-index prism, is designed to produce equal and opposite quarter-wave retardation in reflection and transmission and equal throughput for the p and s polarization at oblique incidence. Such a device splits a beam of incident linearly polarized light into two orthogonally circularly polarized components of equal power that travel in different directions. A visible (633-nm) design that operates at a 60 degree angle of incidence and an infrared (10.6-microm) 45 degree cube design are presented. The spectral and angular sensitivities of the device are also considered.

LLE review, volume 73. Quarterly report, October 1997--December 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1998-04-01

This progress report contains discussion on the following topics: A high-bandwidth electrical-waveform generator based on aperture-coupled striplines for OMEGA pulse-shaping applications; sweep deflection circuit development using computer-aided circuit design for the OMEGA multichannel streak camera; D-{sup 3}He protons as a diagnostic for target {rho}R; growth rates of the ablative Rayleigh-Taylor instability in inertial confinement fusion; three-dimensional analysis of the power transfer between crossed laser beams; characterization of freestanding polymer films for application in 351-nm, high-peak-power laser systems; subsurface damage in microgrinding optical glasses; bound-abrasive polishers for optical glass; and color gamut of cholesteric liquid crystal films and flakes by standardmore » colorimetry.« less

Predictive Engineering Tools for Injection-Molded Long-Carbon-Fiber Thermoplastic Composites - FY 2014 First Quarterly Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nguyen, Ba Nghiep; Sanborn, Scott E.; Simmons, Kevin L.

2014-02-19

The CRADA between PNNL, Autodesk, Toyota and Magna has been effective since October 28th, 2013. The whole team including CRADA and subcontract partners kicked off the project technically on November 1st, 2013. This report describes work performed during the first quarter of FY 2014. The following technical progresses have been made toward project milestones: 1) The project kickoff meeting was organized at PlastiComp, Inc. in Winona on November 13th, 2013 involving all the project partners. During this meeting the research plan and Gantt chart were discussed and refined. The coordination of the research activities among the partners was also discussedmore » to ensure that the deliverables and timeline will be met. 2) Autodesk delivered a research version of ASMI to PNNL for process modeling using this tool under the project. PNNL installed this research version on a PNNL computer and tested it. Currently, PNNL is using ASMI to prepare the models for PlastiComp plaques. 3) PlastiComp has compounded long carbon-fiber reinforced polypropylene and polyamide 6,6 compounds for rheological and thermal characterization tests by the Autodesk laboratories in Melbourne, Australia. 4) Initial mold flow analysis was carried out by PlastiComp to confirm that the 3D complex part selected by Toyota as a representative automotive part is moldable. 5) Toyota, Magna, PlastiComp and PNNL finalized the planning for molding the Toyota 3D complex part. 6) Purdue University worked with PNNL to update and specify the test matrix for characterization of fiber length/orientation. 7) Purdue University developed tools to automate the data collection and analysis of fiber length and orientation measurements. 8) Purdue University designed and specified equipment to replace the need for equipment using the technology established by the University of Leeds at General Motors.« less

FNOC In Situ Technical Support.

DTIC Science & Technology

1982-10-01

09 NM2*20 MSGLINE*14 CONJDP*04 SEXY *05 CON VERT*O7 ACOULAB ACOULAB*06 Correct meter to feet conversion error (if more 20SVP pt). DATE ROUTINE... PORN , TASS, and PTARF (MOFT produces ASRAPL & BLKDATA for FASOTRAGRU moffett). (DRUN*106 S2 4682) B-9 UPDTE DATE: 12/15/81*1 .- PROGRAM PROGRAMMER

Characterization of Rain Attenuation and Depolarization at W/V Bands

DTIC Science & Technology

2015-07-30

AIR FORCE BASE , NM 87117-5776 DTIC COPY NOTICE AND SIGNATURE PAGE Using Government drawings, specifications, or other data included in this...WITH ASSIGNED DISTRIBUTION STATEMENT. //SIGNED// //SIGNED// STEVEN A. LANE PAUL HAUSGEN, Ph.D. Program Manager Technical Advisor, Space Based Advanced... Stations ........................................................................................ 11  Figure 3. Transmitter Block Diagram

Ecosystem disturbance and wildlife conservation in western grasslands - A symposium proceedings

Treesearch

Deborah M. Finch

1996-01-01

This publication is the result of a half-day symposium, "Ecology, management, and sustainability of western grassland ecosystems" held at The Wildlife Society's First Annual Technical Conference, September 22-26, 1994 in Albuquerque, NM. The purpose of the symposium was to review and synthesize information about the structure, function, and...

76 FR 68043 - Federal Acquisition Regulation; Technical Amendments

Federal Register 2010, 2011, 2012, 2013, 2014

2011-11-02

...), and National Aeronautics and Space Administration (NASA). ACTION: Final rule. SUMMARY: This document... Acquisition Policy, Office of Governmentwide Policy. Therefore, DoD, GSA, and NASA amend 48 CFR parts 1 and 8...] 0 4. Amend section 8.501 by removing ``http://www.nm.blm.gov/www/amfo/ amfo_home.html'' and adding...

3. Southwest side of quarters R (commanding officer's quarters), looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Southwest side of quarters R (commanding officer's quarters), looking east - Naval Air Station Chase Field, Quarters R, Essex Street, .43 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

6. Interior of quarters (executive officer's quarters), living room, looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. Interior of quarters (executive officer's quarters), living room, looking west - Naval Air Station Chase Field, Quarters S, Essex Street, .45 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

1. North side of quarters (executive officer's quarters), looking southeast ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. North side of quarters (executive officer's quarters), looking southeast - Naval Air Station Chase Field, Quarters S, Essex Street, .45 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

5. East side of quarters (executive officer's quarters), looking west ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. East side of quarters (executive officer's quarters), looking west - Naval Air Station Chase Field, Quarters S, Essex Street, .45 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

1. Northeast side of Quarters R (commanding officer's quarters), looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. Northeast side of Quarters R (commanding officer's quarters), looking west - Naval Air Station Chase Field, Quarters R, Essex Street, .43 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

2. West side of quarters (executive officer's quarters), looking east ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. West side of quarters (executive officer's quarters), looking east - Naval Air Station Chase Field, Quarters S, Essex Street, .45 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

2. Southeast side of Quarters R (commanding officer's quarters), looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. Southeast side of Quarters R (commanding officer's quarters), looking northwest - Naval Air Station Chase Field, Quarters R, Essex Street, .43 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

4. Northwest side of Quarters R (commanding officer's quarters), looking ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. Northwest side of Quarters R (commanding officer's quarters), looking southeast - Naval Air Station Chase Field, Quarters R, Essex Street, .43 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

4. South side of quarters (executive officer's quarters), looking north ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

4. South side of quarters (executive officer's quarters), looking north - Naval Air Station Chase Field, Quarters S, Essex Street, .45 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

3. Southwest side of quarters (executive officer's quarters), looking northeast ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

3. Southwest side of quarters (executive officer's quarters), looking northeast - Naval Air Station Chase Field, Quarters S, Essex Street, .45 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

5. Interior of Quarters R (commanding officer's quarters), living room, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

5. Interior of Quarters R (commanding officer's quarters), living room, looking northwest - Naval Air Station Chase Field, Quarters R, Essex Street, .43 mile South-Southeast of intersection of Texas State Highway 202 & Independence Street, Beeville, Bee County, TX

33 CFR 117.261 - Atlantic Intracoastal Waterway from St. Marys River to Key Largo.

Code of Federal Regulations, 2012 CFR

2012-07-01

... draw shall open on the quarter and three-quarter hour. (u) Flagler Memorial (SR A1A) bridge, mile 1020... (SR 700/80) bridge, mile 1024.7 at Palm Beach. The draw shall open on the quarter and three-quarter... open on the quarter and three-quarter-hour. (z-2) Linton Boulevard bridge, mile 1041.1, at Delray Beach...

33 CFR 117.261 - Atlantic Intracoastal Waterway from St. Marys River to Key Largo.

Code of Federal Regulations, 2011 CFR

2011-07-01

... draw shall open on the quarter and three-quarter hour. (u) Flagler Memorial (SR A1A) bridge, mile 1020... (SR 700/80) bridge, mile 1024.7 at Palm Beach. The draw shall open on the quarter and three-quarter... open on the quarter and three-quarter-hour. (z-2) Linton Boulevard bridge, mile 1041.1, at Delray Beach...

33 CFR 117.261 - Atlantic Intracoastal Waterway from St. Marys River to Key Largo.

Code of Federal Regulations, 2013 CFR

2013-07-01

... draw shall open on the quarter and three-quarter hour. (u) Flagler Memorial (SR A1A) bridge, mile 1020... (SR 700/80) bridge, mile 1024.7 at Palm Beach. The draw shall open on the quarter and three-quarter... open on the quarter and three-quarter-hour. (z-2) Linton Boulevard bridge, mile 1041.1, at Delray Beach...

[Development of cell content and shedding of Prototheca spp. in milk from infected udder quarters of cows].

PubMed

Tenhagen, B A; Hille, A; Schmidt, A; Heuwieser, W

2005-02-01

It was the objective of this study to analyse shedding patterns and somatic cell counts in cows and quarters infected with Prototheca spp. and to evaluate two approaches to identify infected animals by somatic cell count (SCC) or by bacteriological analysis of pooled milk samples. Five lactating dairy cows, chronically infected with Prototheca spp. in at least one quarter were studied over 11 weeks to 13 months. Quarter milk samples and a pooled milk sample from 4 quarters were collected aseptically from all quarters of the cows on a weekly basis. Culture results of quarter milk and pooled samples were compared using cross tabulation. SCC of quarter milk samples and of pooled samples were related to the probability of detection in the infected quarters and cows, respectively. Shedding of Prototheca spp. was continuous in 2 of 8 quarters. In the other quarters negative samples were obtained sporadically or over a longer period (1 quarter). Overall, Prototheca spp. were isolated from 83.6% of quarter milk samples and 77.0% of pooled milk samples of infected quarters and cows. Somatic cell counts were higher in those samples from infected quarters that contained the algae than in negative samples (p < 0.0001). The same applied for composite samples from infected cows. Positive samples had higher SCC than negative samples. However, Prototheca spp. were also isolated from quarter milk and pooled samples with physiological SCC (i.e. < 10(5)/ml). Infected quarters that were dried off did not develop acute mastitis. However, drying off had no effect on the infection, i.e. samples collected at calving or 8 weeks after dry off still contained Prototheca spp. Results indicate that pre-selection of cows to be sampled for Prototheca spp. by SCC and the use of composite samples are probably inadequate in attempts to eradicate the disease. However, due to intermittent shedding of the algae in some cows, single herd sampling using quarter milk samples probably also fails to detect all infected cases. Therefore, continuous monitoring of problem cows with clinical mastitis or increased SCC in herds during eradication programs is recommended.

Advanced Insulation for High Performance Cost-Effective Wall, Roof, and Foundation Systems Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Costeux, Stephane; Bunker, Shanon

The objective of this project was to explore and potentially develop high performing insulation with increased R/inch and low impact on climate change that would help design highly insulating building envelope systems with more durable performance and lower overall system cost than envelopes with equivalent performance made with materials available today. The proposed technical approach relied on insulation foams with nanoscale pores (about 100 nm in size) in which heat transfer will be decreased. Through the development of new foaming methods, of new polymer formulations and new analytical techniques, and by advancing the understanding of how cells nucleate, expand andmore » stabilize at the nanoscale, Dow successfully invented and developed methods to produce foams with 100 nm cells and 80% porosity by batch foaming at the laboratory scale. Measurements of the gas conductivity on small nanofoam specimen confirmed quantitatively the benefit of nanoscale cells (Knudsen effect) to increase insulation value, which was the key technical hypotheses of the program. In order to bring this technology closer to a viable semi-continuous/continuous process, the project team modified an existing continuous extrusion foaming process as well as designed and built a custom system to produce 6" x 6" foam panels. Dow demonstrated for the first time that nanofoams can be produced in a both processes. However, due to technical delays, foam characteristics achieved so far fall short of the 100 nm target set for optimal insulation foams. In parallel with the technology development, effort was directed to the determination of most promising applications for nanocellular insulation foam. Voice of Customer (VOC) exercise confirmed that demand for high-R value product will rise due to building code increased requirements in the near future, but that acceptance for novel products by building industry may be slow. Partnerships with green builders, initial launches in smaller markets (e.g. EIFS), and efforts to drive cost down will help acceptance in residential and commercial retrofit and new construction.« less

Integrated Optical Circuit Engineering For Optical Fiber Gyrocopes

NASA Astrophysics Data System (ADS)

Bristow, Julian P.; We, Albert C.; Keur, M.; Lukas, Greg; Ott, Daniel M...; Sriram, S.

1988-03-01

Fiber optic gyroscopes are of interest for low-cost, high performance rotation sensors. Integrated optical implementations of the processing optics offer the hope of mass-production, and associated cost reductions. The development of a suitable integrated optical system has been reported by other authors at a wavelength of 850nm [1]. Despite strong technical advantages at 1.3μm wavelength [2], no results have yet appeared. This wavelength is preferred for telecommunications applications applications, thus significantly reduced fiber costs may be realized. Lithium niobate is relatively immune from the photorefractive effect at this wavelength, whereas it is not at at 850nm [3].

Protection efficiency of a standard compliant EUV reticle handling solution

NASA Astrophysics Data System (ADS)

He, Long; Lystad, John; Wurm, Stefan; Orvek, Kevin; Sohn, Jaewoong; Ma, Andy; Kearney, Patrick; Kolbow, Steve; Halbmaier, David

2009-03-01

For successful implementation of extreme ultraviolet lithography (EUVL) technology for late cycle insertion at 32 nm half-pitch (hp) and full introduction for 22 nm hp high volume production, the mask development infrastructure must be in place by 2010. The central element of the mask infrastructure is contamination-free reticle handling and protection. Today, the industry has already developed and balloted an EUV pod standard for shipping, transporting, transferring, and storing EUV masks. We have previously demonstrated that the EUV pod reticle handling method represents the best approach in meeting EUVL high volume production requirements, based on then state-of-the-art inspection capability at ~53nm polystyrene latex (PSL) equivalent sensitivity. In this paper, we will present our latest data to show defect-free reticle handling is achievable down to 40 nm particle sizes, using the same EUV pod carriers as in the previous study and the recently established world's most advanced defect inspection capability of ~40 nm SiO2 equivalent sensitivity. The EUV pod is a worthy solution to meet EUVL pilot line and pre-production exposure tool development requirements. We will also discuss the technical challenges facing the industry in refining the EUV pod solution to meet 22 nm hp EUVL production requirements and beyond.

Technical Errors May Affect Accuracy of Torque Limiter in Locking Plate Osteosynthesis.

PubMed

Savin, David D; Lee, Simon; Bohnenkamp, Frank C; Pastor, Andrew; Garapati, Rajeev; Goldberg, Benjamin A

2016-01-01

In locking plate osteosynthesis, proper surgical technique is crucial in reducing potential pitfalls, and use of a torque limiter makes it possible to control insertion torque. We conducted a study of the ways in which different techniques can alter the accuracy of torque limiters. We tested 22 torque limiters (1.5 Nm) for accuracy using hand and power tools under different rotational scenarios: hand power at low and high velocity and drill power at low and high velocity. We recorded the maximum torque reached after each torque-limiting event. Use of torque limiters under hand power at low velocity and high velocity resulted in significantly (P < .0001) different mean (SD) measurements: 1.49 (0.15) Nm and 3.73 (0.79) Nm. Use under drill power at controlled low velocity and at high velocity also resulted in significantly (P < .0001) different mean (SD) measurements: 1.47 (0.14) Nm and 5.37 (0.90) Nm. Maximum single measurement obtained was 9.0 Nm using drill power at high velocity. Locking screw insertion with improper technique may result in higher than expected torque and subsequent complications. For torque limiters, the most reliable technique involves hand power at slow velocity or drill power with careful control of insertion speed until 1 torque-limiting event occurs.

Reader-Centered Technical Writing

NASA Astrophysics Data System (ADS)

Narayanan, M.

2012-12-01

Technical writing is an essential part of professional communication and in recent years it has shifted from a genre-based approach. Formerly, technical writing primarily focused on generating templates of documents and sometimes it was creating or reproducing traditional forms with minor modifications and updates. Now, technical writing looks at the situations surrounding the need to write. This involves deep thinking about the goals and objectives of the project on hand. Furthermore, one observes that it is very important for any participatory process to have the full support of management. This support needs to be well understood and believed by employees. Professional writing may be very persuasive in some cases. When presented in the appropriate context, technical writing can persuade a company to improve work conditions ensuring employee safety and timely production. However, one must recognize that lot of professional writing still continues to make use of reports and instruction manuals. Normally, technical and professional writing addresses four aspects. Objective: The need for generating a given professionally written technical document and the goals the document is expected to achieve and accomplish. Clientele: The clientele who will utilize the technical document. This may include the people in the organization. This may also include "unintended readers." Customers: The population that may be affected by the content of the technical document generated. This includes the stakeholders who will be influenced. Environment: The background in which the document is created. Also, the nature of the situation that warranted the generation of the document. Swiss Psychologist Jean Piaget's view of Learning focuses on three aspects. The author likes to extend Jean Piaget's ideas to students, who are asked to prepare and submit Reader-Centered Technical Writing reports and exercises. Assimilation: Writers may benefit specifically, by assimilating a new object into an old schema. This reinforces basic engineering and mathematical design concepts. Accommodation: Here, it may work in a different manner. Writers may have to accommodate an old schema to a new object. This helps engineers to focus more on applications. Adaptation: Assimilation and accommodation are the two sides of adaptation, Jean Piaget's term for what most of us would call learning. Mathematical design concepts generated by students should be suitable for creative engineering applications. References : Phillips, D. C. and Soltis, Jonas F. (2003) "Piagetian Structures and Psychological Constructivism," in Perspectives on Learning (4th edition). New York: Teachers College Press. Salvo, Michael J. (2001). Ethics of Engagement: User-Centered Design and Rhetorical Methodology. Technical Communication Quarterly Volume 10, Issue 3, 2001. pages 273-290. http://www.ship.edu/~cgboeree/piaget.html http://owl.english.purdue.edu/owl/resource/624/01/

High-numerical aperture extreme ultraviolet scanner for 8-nm lithography and beyond

NASA Astrophysics Data System (ADS)

Schoot, Jan van; Setten, Eelco van; Rispens, Gijsbert; Troost, Kars Z.; Kneer, Bernhard; Migura, Sascha; Neumann, Jens Timo; Kaiser, Winfried

2017-10-01

Current extreme ultraviolet (EUV) projection lithography systems exploit a projection lens with a numerical aperture (NA) of 0.33. It is expected that these will be used in mass production in the 2018/2019 timeframe. By then, the most difficult layers at the 7-nm logic and the mid-10-nm DRAM nodes will be exposed. These systems are a more economical alternative to multiple-exposure by 193 argon fluoride immersion scanners. To enable cost-effective shrink by EUV lithography down to 8-nm half pitch, a considerably larger NA is needed. As a result of the increased NA, the incidence angles of the light rays at the mask increase significantly. Consequently, the shadowing and the variation of the multilayer reflectivity deteriorate the aerial image contrast to unacceptably low values at the current 4× magnification. The only solution to reduce the angular range at the mask is to increase the magnification. Simulations show that the magnification has to be doubled to 8× to overcome the shadowing effects. Assuming that the mask infrastructure will not change the mask form factor, this would inevitably lead to a field size that is a quarter of the field size of the current 0.33-NA step and scan systems and reduce the throughput (TPT) of the high-NA scanner to a value below 100 wafers per hour unless additional measures are taken. This paper presents an anamorphic step and scan system capable of printing fields that are half the field size of the current full field. The anamorphic system has the potential to achieve a TPT in excess of 150 wafers per hour by increasing the transmission of the optics, as well as increasing the acceleration of the wafer stage and mask stage. This makes it an economically viable lithography solution.

12 CFR 1777.10 - Developments prompting supervisory response.

Code of Federal Regulations, 2010 CFR

2010-01-01

... less than the national HPI four quarters previously, or for any Census Division or Divisions in which... more than five percent less than the HPI for that Division or Divisions four quarters previously; (b...-half of its average quarterly net income for any four-quarter period during the prior eight quarters...

18 CFR 35.10b - Electric Quarterly Reports.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Electric Quarterly... Application § 35.10b Electric Quarterly Reports. Each public utility shall file an updated Electric Quarterly..., file by January 31. Electric Quarterly Reports must be prepared in conformance with the Commission's...

18 CFR 35.10b - Electric Quarterly Reports.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 18 Conservation of Power and Water Resources 1 2011-04-01 2011-04-01 false Electric Quarterly... Application § 35.10b Electric Quarterly Reports. Each public utility shall file an updated Electric Quarterly..., file by January 31. Electric Quarterly Reports must be prepared in conformance with the Commission's...

18 CFR 35.10b - Electric Quarterly Reports.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 18 Conservation of Power and Water Resources 1 2012-04-01 2012-04-01 false Electric Quarterly... Application § 35.10b Electric Quarterly Reports. Each public utility shall file an updated Electric Quarterly..., file by January 31. Electric Quarterly Reports must be prepared in conformance with the Commission's...

Low Group Delay Dispersion Optical Coating for Broad Bandwidth High Reflection at 45° Incidence, P Polarization of Femtosecond Pulses with 900 nm Center Wavelength

DOE PAGES

Bellum, John C.; Field, Ella S.; Winstone, Trevor B.; ...

2016-03-01

We describe an optical coating design suitable for broad bandwidth high reflection (BBHR) at 45° angle of incidence (AOI), P polarization (Ppol) of femtosecond (fs) laser pulses whose wavelengths range from 800 to 1000 nm. The design process is guided by quarter-wave HR coating properties. Our design must afford low group delay dispersion (GDD) for reflected light over the broad, 200 nm bandwidth in order to minimize temporal broadening of the fs pulses due to dispersive alteration of relative phases between their frequency components. The design should also be favorable to high laser-induced damage threshold (LIDT). We base the coatingmore » on TiO 2/SiO 2 layer pairs produced by means of e-beam evaporation with ion-assisted deposition, and use OptiLayer Thin Film Software to explore designs starting with TiO 2/SiO 2 layers having thicknesses in a reverse chirped arrangement. This approach led to a design with R > 99% from 800 to 1000 nm and GDD < 20 fs 2 from 843 to 949 nm (45° AOI, Ppol). The design’s GDD behaves in a smooth way, suitable for GDD compensation techniques, and its electric field intensities show promise for high LIDTs. Reflectivity and GDD measurements for the initial test coating indicate good performance of the BBHR design. Subsequent coating runs with improved process calibration produced two coatings whose HR bands satisfactorily meet the design goals. Lastly, for the sake of completeness, we summarize our previously reported transmission spectra and LIDT test results with 800 ps, 8 ps and 675 fs pulses for these two coatings, and present a table of the LIDT results we have for all of our TiO 2/SiO 2 BBHR coatings, showing the trends with test laser pulse duration from the ns to sub-ps regimes.« less

DOE Eastern Gas Shales Project: Dunkirk study. Quarterly report of technical progress, July, August, September 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harper, J.A.; Abel, K.D.; Piotrowski, R.G.

Ten cross sections were completed and drafted, and blueline copies were sent to DOE, Morgantown, WV, for review. These cross sections were used as the basis with which all other logs in the study area were correlated. The data has been encoded from 228 logs that were used. Two isopach, 2 structure contour, and 3 lithofacies maps have been completed and are awaiting drafting. A production and show map has been drafted and blueline copies were sent to DOE, Morgantown, WV, for review. The schedule of work was delayed due to the state budget problems the need to correct workmore » previously completed and sent to DOE, Morgantown, WV, and lack of a reproduction contract.« less

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kizilyalli, Isik; Evans, Craig; Matocha, Kevin

The ARPA-E model is unique in that the agency does not just provide teams funding. Throughout the lifetime of an ARPA-E award, ARPA-E Program Directors and Tech-to-Market Advisors also provide teams with expert advice through quarterly reviews and onsite visits. This hands-on approach helps ensure teams can meet ambitious milestones, target and tackle problems early on, and advance their technologies towards commercialization. Program Director Dr. Isik Kizilyalli explains the importance of this active project management approach in helping teams identify and overcome barriers. In this video, Energy Storage Systems (ESS) from the GRIDS program and Monolith Semiconductors from the SWITCHESmore » program discuss how ARPA-E’s active project management approach helped them find solutions to technical challenges.« less

Comment on "Effect of coal-fired power generation on visibility in a nearby National Park (Terhorst and Berkman, 2010)"

NASA Astrophysics Data System (ADS)

White, W. H.; Farber, R. J.; Malm, W. C.; Nuttall, M.; Pitchford, M. L.; Schichtel, B. A.

2012-08-01

Few electricity generating stations received more environmental scrutiny during the last quarter of the twentieth century than did the Mohave Power Project (MPP), a coal-fired facility near Grand Canyon National Park. Terhorst and Berkman (2010) examine regional aerosol monitoring data collected before and after the plant's 2006 retirement for retrospective evidence of MPP's impact on visibility in the Park. The authors' technical analysis is thoughtfully conceived and executed, but is misleadingly presented as discrediting previous studies and their interpretation by regulators. In reality the Terhorst-Berkman analysis validates a consensus on MPP's visibility impact that was established years before its closure, in a collaborative assessment undertaken jointly by Federal regulators and MPP's owners.

Production of aluminum-silicon alloy and ferrosilicon and commercial purity aluminum by the direct reduction process. Third interim technical report, Phase C for the period 1980 July 1-1980 September 30

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruno, M.J.

1980-10-01

Pilot reactor VSR-3 operation in the third quarter was directed to tapping molten alloy product. Modifications to the hearth region included a tapping furnace to maintain taphole temperature, a graphite ring filter to separate carbides from matal and an alumina liner to eliminate carbiding from reaction of alloy with the graphite hearth walls. Tapping was not successful, however, due to high alloy viscosity from a large concentration of carbides. Three runs were made on the pilot crystallizer to determine the effects of alloy composition, cooling rate, tamping rate, remelt temperature and rate on eutectic Al-Si yield.

The Structure and Dynamics of the Solar Corona and Inner Heliosphere

NASA Technical Reports Server (NTRS)

Mikic, Zoran

2002-01-01

This report covers technical progress during the second quarter of the first year of NASA Sun-Earth Connections Theory Program (SECTP) contract 'The Structure and Dynamics of the Solar Corona and Inner Heliosphere,' NAS5-99188, between NASA and Science Applications International Corporation. and covers the period November 16, 1999 to February 15, 2000. Under this contract SAIC and the University of California, Irvine (UCI) have conducted research into theoretical modeling of active regions, the solar corona, and the inner heliosphere, using the MHD (magnetohydrodynamic) model. The topics studied include: the effect of emerging flux on the stability of helmet streamers, coronal loops and streamers, the solar magnetic field, the solar wind, and open magnetic field lines.

Calendar Year 2016 Annual Groundwater Monitoring Report.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Copland, John R.; Jackson, Timmie Okchumpulla; Li, Jun

Sandia National Laboratories, New Mexico (SNL/NM) is a government-owned/contractoroperated laboratory. National Technology and Engineering Solutions of Sandia, LLC, a wholly owned subsidiary of Honeywell International, Inc., manages and operates SNL/NM for the U.S. Department of Energy (DOE), National Nuclear Security Administration (NNSA). The DOE/NNSA Sandia Field Office administers the contract and oversees contractor operations at the site. Two types of groundwater surveillance monitoring are conducted at SNL/NM: (1) on a site-wide basis as part of the SNL/NM Long-Term Stewardship (LTS) Program’s Groundwater Monitoring Program (GMP) Groundwater Surveillance Task and (2) on a site-specific groundwater monitoring at LTS/Environmental Restoration (ER) Operationsmore » sites with ongoing groundwater investigations. This Annual Groundwater Monitoring Report summarizes data collected during groundwater monitoring events conducted at GMP locations and at the following SNL/NM sites through December 31, 2016: Burn Site Groundwater Area of Concern (AOC); Chemical Waste Landfill; Mixed Waste Landfill; Technical Area-V Groundwater AOC; and the Tijeras Arroyo Groundwater AOC. Environmental monitoring and surveillance programs are required by the New Mexico Environment Department (NMED) and DOE Order 436.1, Departmental Sustainability, and DOE Order 231.1B, Environment, Safety, and Health Reporting.« less

Sustaining western grasslands and associated wildlife: An introduction

Treesearch

Deborah M. Finch

1996-01-01

This publication is the result of a half-day symposium, "Ecology, management, and sustainability of western grassland ecosystems," held at The Wildlife Society’s First Annual Technical Conference, September 22-26, 1994 in Albuquerque, NM. The symposium was sponsored by The Wildlife Society's Working Group on Sustainable Use of Ecosystem Resources and was...

Designing to win in sub-90nm mask production

NASA Astrophysics Data System (ADS)

Zhang, Yuan

2005-11-01

An informal survey conducted with key customers by Photronics indicates that the time gap between technology nodes has accelerated in recent years. Previously the cycle was three years. However, between 130nm and 90nm there was less than a 2 year gap, and between 90nm and 65nm a 1.5 year gap exists. As a result, the technical challenges have increased substantially. In addition, mask costs are rising exponentially due to high capital equipment cost, a shrinking customer base, long write times and increased applications of 193nm EAPSM or AAPSM. Collaboration among EDA companies, mask houses and wafer manufacturers is now more important than ever. This paper will explore avenues for reducing mask costs, mainly in the areas of: write-time reduction through design for manufacturing (DFM), and yield improvement through specification relaxation. Our study conducted through layout vertex modeling suggests that a simple design shape such as a square versus a circle or an angled structure helps reduce shot count and write time. Shot count reduction through mask layout optimization, and advancement in new generation E-beam writers can reduce write time up to 65%. An advanced laser writer can produce those less critical E-beam layers in less than half the time of an e-beam writer. Additionally, the emerging imprint lithography brings new life and new challenges to the photomask industry with applications in many fields outside of the semiconductor industry. As immersion lithography is introduced for 45nm device production, polarization and MEEF effects due to the mask will become severe. Larger magnification not only provides benefits on CD control and MEEF, but also extends the life time of current 90nm/65nm tool sets where 45nm mask sets can be produced at a lower cost.

Exploration of BEOL line-space patterning options at 12 nm half-pitch and below

NASA Astrophysics Data System (ADS)

Decoster, S.; Lazzarino, F.; Petersen Barbosa Lima, L.; Li, W.; Versluijs, J.; Halder, S.; Mallik, A.; Murdoch, G.

2018-03-01

While the semiconductor industry is almost ready for high-volume manufacturing of the 7 nm technology node, research centers are defining and troubleshooting the patterning options for the 5 nm technology node (N5) and below. The target dimension for imec's N5 BEOL applications is 20-24 nm Metal Pitch (MP), which requires Self-Aligned multiple (Double/Quadruple/Octuple) Patterning approaches (SAxP) in combination with EUV or immersion lithography at 193 nm. There are numerous technical challenges to enable gratings at the hard mask level such as good uniformity across wafer, low line edge/width roughness (LER/LWR), large process window, and all of this at low cost. An even greater challenge is to transfer these gratings into the dielectric material at such critical dimensions, where increased line edge roughness, line wiggling and even pattern collapse can be expected for materials with small mechanical stability such as highly porous low-k dielectrics. In this work we first compare three different patterning options for 12 nm half-pitch gratings at the hard mask level: EUV-based SADP and 193i-based SAQP and SAOP. This comparison will be based on process window, line edge/width roughness and cost. Next, the transfer of 12 nm line/space gratings in the dielectric material is discussed and presented. The LER of the dielectric lines is investigated as a function of the dielectric material, the trench depth, and the stress in the sacrificial hard mask. Finally, we elaborate on the different options to enable scaling down from 24 nm MP to 16 nm MP, and demonstrate 8 nm line/space gratings with 193i-based SAOP.

Idaho National Laboratory Quarterly Occurrence Analysis 4th Quarter FY 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Lisbeth Ann

This report is published quarterly by the Idaho National Laboratory (INL) Quality and Performance Management Organization. The Department of Energy (DOE) Occurrence Reporting and Processing System, as prescribed in DOE Order 232.2, “Occurrence Reporting and Processing of Operations Information,” requires a quarterly analysis of events, both reportable and not reportable, for the previous 12 months. This report is the analysis of 84 reportable events (29 from the 4th quarter fiscal year 2016 and 55 from the prior three reporting quarters), as well as 39 other issue reports (including events found to be not reportable and Significant Category A and Bmore » conditions) identified at INL during the past 12 months (two from this quarter and 37 from the prior three quarters).« less

UV lifetime laser demonstrator for space-based applications

NASA Astrophysics Data System (ADS)

Albert, Michael; Puffenburger, Kent; Schum, Tom; Fitzpatrick, Fran; Litvinovitch, Slava; Jones, Darrell; Rudd, Joseph; Hovis, Floyd

2015-09-01

A long-lived UV laser is an enabling technology for a number of high-priority, space-based lidar instruments. These include next generation cloud and aerosol lidars that incorporates a UV channel, direct detection 3-D wind lidars, and ozone DIAL (differential absorption lidar) system. In previous SBIR funded work we developed techniques for increasing the survivability of components in high power UV lasers and demonstrated improved operational lifetimes. In this Phase III ESTO funded effort we are designing and building a TRL (Technology Readiness Level) 6 demonstrator that will have increased output power and a space-qualifiable package that is mechanically robust and thermally-stable. For full space compatibility, thermal control will be through pure conductive cooling. Contamination control processes and optical coatings will be chosen that are compatible with lifetimes in excess of 1 billion shots. The 1064nm output will be frequency tripled to provide greater than 100mJ pulses of 355nm light at 150 Hz. After completing the laser module build in the third quarter of 2015 we will initiate lifetime testing, followed by thermal/vacuum (TVAC) and vibration testing to demonstrate that the design is at TRL 6.

Characterization of Electron Temperature and Density Profiles of Plasmas Produced by Nike KrF Laser for Laser Plasma Instability (LPI) Research

NASA Astrophysics Data System (ADS)

Oh, Jaechul; Weaver, J. L.; Phillips, L.; Obenschain, S. P.; Schmitt, A. J.; Kehne, D. M.; Chan, L.-Y.; Serlin, V.

2011-10-01

Previous experiments with Nike KrF laser (λ = 248 nm , Δν ~ 1 THz) observed LPI signatures near quarter critical density (nc / 4) in CH plasmas, however, detailed measurement of the temperature (Te) and density (ne) profiles was missing. The current Nike LPI campaign will perform experimental determination of the plasma profiles. A side-on grid imaging refractometer (GIR) is the main diagnostic to resolve Te and ne in space taking 2D snapshots of probe laser (λ = 266 nm , Δt = 8 psec) beamlets (50 μm spacing) refracted by the plasma at laser peak time. Ray tracing of the beamlets through hydrodynamically simulated (FASTRAD3D) plasma profiles estimates the refractometer may access densities up to ~ 0 . 2nc . With the measured Te and ne profiles in the plasma corona, we will discuss analysis of light data radiated from the plasmas in spectral ranges relevant to two plasmon decay and convective Raman instabilities. Validity of the (Te ,ne) data will also be discussed for the thermal transport study. Work supported by DoE/NNSA and ONR and performed at NRL.

Quarterly environmental data summary for first quarter 1999

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

In support of the Weldon Spring Site Remedial Action Project Federal Facilities Agreement, a copy of the Quarterly Environmental Data Summary (QEDS) for the first quarter of 1999 is enclosed. The data presented in this constitute the QEDS. The data, except for air monitoring data and site KPA generated data (uranium analyses), were received from the contract laboratories, verified by the Weldon Spring Site verification group and merged into the database during the first quarter of 1999. KPA results for on-site total uranium analyses performed during first quarter 1999 are included. Air monitoring data presented are the most recent completemore » sets of quarterly data.« less

Two-probe STM experiments at the atomic level.

PubMed

Kolmer, Marek; Olszowski, Piotr; Zuzak, Rafal; Godlewski, Szymon; Joachim, Christian; Szymonski, Marek

2017-11-08

Direct characterization of planar atomic or molecular scale devices and circuits on a supporting surface by multi-probe measurements requires unprecedented stability of single atom contacts and manipulation of scanning probes over large, nanometer scale area with atomic precision. In this work, we describe the full methodology behind atomically defined two-probe scanning tunneling microscopy (STM) experiments performed on a model system: dangling bond dimer wire supported on a hydrogenated germanium (0 0 1) surface. We show that 70 nm long atomic wire can be simultaneously approached by two independent STM scanners with exact probe to probe distance reaching down to 30 nm. This allows direct wire characterization by two-probe I-V characteristics at distances below 50 nm. Our technical results presented in this work open a new area for multi-probe research, which can be now performed with precision so far accessible only by single-probe scanning probe microscopy (SPM) experiments.

Cultural resources regulatory analysis, area overview, and assessment of previous Department of Energy and Kirtland Air Force Base inventories for Sandia National Laboratories, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoagland, S.R.; Lord, K.J.

The following regulatory analysis and literature review of archaeological and historic resources on the Sandia National Laboratory/New Mexico (SNL/NM) occupied properties was prepared by the Chambers Group Inc. in January 1992. Based upon compliance surveys of Technical Area I through V undertaken in 1990 and 1991 the report concludes that, although consultation with the Department of Energy and State Historic Preservation Officer will still be required for particular projects, cultural resources should not affect the overall planning and development of future SNL/NM projects. As SNL/NM buildings approach 50 years in age additional analysis and consultations may be required. In ordermore » to protect sensitive resources, the location coordinates and maps provided in the original report are not included here.« less

Spectrally narrowed laserlike emission in a novel organic salt, DEST: cooperative emission

NASA Astrophysics Data System (ADS)

Tan, Shida; Mishra, Alpana; Ahyi, Ayayi; Bhowmik, Achintya; Dharmadhikari, Aditya; Thakur, Mrinal

2001-03-01

We have synthesized a novel organic salt, 4'-diethylamino-N-methyl-4-stilbazolium p-toluenesulfonate (DEST). Frequency-doubled pulses (55 ps) from a Nd:YAG laser at 10 Hz repetition rate were used to pump DEST solution in methanol and a 20% conversion efficiency in laserlike emission was observed without external mirrors. The low energy PL quantum efficiency of DEST is very low. The peak of the emission spectrum was at 617 nm and the threshold pump energy for spectral-narrowing was less than 1 μJ. Beyond the threshold, the FWHM of the spectrum was found to have reduced from 70 nm to 14 nm The characteristics are similar to that of another organic salt, SPCD^1, which has been recently reported. Cooperative emission appears to play a dominant role in this emission process. 1. A. K. Bhowmik, A. Dharmadhikari, and M. Thakur, OSA Technical Digest, 467, CLEO (1999).

Properties of magnetic photonic crystals in the visible spectral region and their performance limitations

NASA Astrophysics Data System (ADS)

Kotov, V. A.; Shavrov, V. G.; Vasiliev, M.; Alameh, K.; Nur-E-Alam, M.; Balabanov, D. E.

2018-02-01

We report on the results of computer modelling and performance analysis of the optical and magneto-optical (MO) characteristics of one-dimensional magnetic photonic crystals (MPC) of several classic design types (having either a single structure defect, or a number of these), designed for applications in the visible spectral region. The calculations are performed accounting for the real levels of optical absorption achievable in existing MO materials which currently demonstrate the best MO quality (bismuth-substituted ferrite garnets). We consider Bi2Dy1Fe4Ga1O12 as the base material for use within quarter-wave thick MO layers of MPC; silica is used for the non-magnetic transparent quarter-wave layers. The achieved results can be used to clarify the nature of the differences that exist between the expected practical potential of MPCs in integrated photonics, and the actual attained experimental results. Our results show that in MPCs optimized for light intensity modulation applications, in the red spectral region (near 650 nm), the achievable levels of optical transmission are limited to about 30%. This coincides spectrally with the peaks of Faraday rotation reaching their maxima at about 25°, with further transmission increases possible in the near-infrared region. Larger Faraday rotation angles are only achievable currently in structures or single film layers with reduced transmission.

Light attenuation characteristics of glacially-fed lakes

NASA Astrophysics Data System (ADS)

Rose, Kevin C.; Hamilton, David P.; Williamson, Craig E.; McBride, Chris G.; Fischer, Janet M.; Olson, Mark H.; Saros, Jasmine E.; Allan, Mathew G.; Cabrol, Nathalie

2014-07-01

Transparency is a fundamental characteristic of aquatic ecosystems and is highly responsive to changes in climate and land use. The transparency of glacially-fed lakes may be a particularly sensitive sentinel characteristic of these changes. However, little is known about the relative contributions of glacial flour versus other factors affecting light attenuation in these lakes. We sampled 18 glacially-fed lakes in Chile, New Zealand, and the U.S. and Canadian Rocky Mountains to characterize how dissolved absorption, algal biomass (approximated by chlorophyll a), water, and glacial flour contributed to attenuation of ultraviolet radiation (UVR) and photosynthetically active radiation (PAR, 400-700 nm). Variation in attenuation across lakes was related to turbidity, which we used as a proxy for the concentration of glacial flour. Turbidity-specific diffuse attenuation coefficients increased with decreasing wavelength and distance from glaciers. Regional differences in turbidity-specific diffuse attenuation coefficients were observed in short UVR wavelengths (305 and 320 nm) but not at longer UVR wavelengths (380 nm) or PAR. Dissolved absorption coefficients, which are closely correlated with diffuse attenuation coefficients in most non-glacially-fed lakes, represented only about one quarter of diffuse attenuation coefficients in study lakes here, whereas glacial flour contributed about two thirds across UVR and PAR. Understanding the optical characteristics of substances that regulate light attenuation in glacially-fed lakes will help elucidate the signals that these systems provide of broader environmental changes and forecast the effects of climate change on these aquatic ecosystems.

78 FR 23903 - Proposed Information Collection; Comment Request; Quarterly Summary of State and Local Government...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-23

... Quarterly Summary of State and Local Government Tax Revenue, using the F-71 (Quarterly Survey of Property Tax Collections), F-72 (Quarterly Survey of State Tax Collections), and F-73 (Quarterly Survey of Non... data for individual states. The information contained in this survey is the most current information...

29 CFR 548.306 - Average earnings for year or quarter year preceding the current quarter.

Code of Federal Regulations, 2011 CFR

2011-07-01

... PAY Interpretations Authorized Basic Rates § 548.306 Average earnings for year or quarter year... regular rates of pay during the current quarter year, and (ii) such average hourly remuneration during the... 29 Labor 3 2011-07-01 2011-07-01 false Average earnings for year or quarter year preceding the...

2. View to northeast showing quarters and outbuildings, L to ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

2. View to northeast showing quarters and outbuildings, L to R: Service Building (HABS No. VA-1287-D), Medical Officer's Quarters C (in background), Garage (HABS No. VA-1287-F), and Medical Officer's Quarters B - Portsmouth Naval Hospital, Medical Officer's Quarters C, West side Williamson Drive, 400 feet South of Rixey Drive, Portsmouth, Portsmouth, VA

Adjustment Notes for Apprentice and Trainee Estimates: December Quarter 2014. Support Document

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2015

2015-01-01

Apprentice and trainee data are reported by the State and Territory Training Authorities to National Centre for Vocational Education Research (NCVER) on a quarterly basis, starting at the September quarter of 1994. The set of data submitted that quarter is referred to as Collection 1. The sets of data submitted in subsequent quarters are referred…

Variation in the composition of selected milk fraction samples from healthy and mastitic quarters, and its significance for mastitis diagnosis.

PubMed

Bansal, Baljinder K; Hamann, Joern; Grabowskit, Nils Th; Singh, Krishan B

2005-05-01

Seven variables--electrical conductivity (EC), somatic cell count (SCC), N-acetyl-beta-D-glucosaminidase (NAGase), lactose, protein, fat and pH--were compared in four quarter milk fractions (MF1: strict foremilk; MF2: first 12-15 ml foremilk; MF3: subsequent 40-45 ml milk; MF4: strippings) and in one cow composite milk sample (CC) per cow. The study used 142 quarters from 37 lactating cows of the German Black Pied breed. To rule out any possible effect due to management, animal physiology and analytical procedures, the collection and processing of milk samples from each cow was repeated for three consecutive days, and the means of 3-d values were used. All variables were affected significantly by milk fraction and udder health. Compared with foremilk, EC, lactose and protein levels in strippings decreased, while SCC, NAGase and fat increased. The pH of foremilk and strippings did not differ significantly in healthy or in mastitic quarters. The difference between MF1 and MF2 was significant for EC in mastitic quarters, and for SCC in healthy quarters only. In general, mastitis resulted in a significant increase in EC, SCC, NAGase and protein but in a decrease in lactose and fat contents of milk in one or more of the milk fractions studied. Comparison of cow composite milk samples from healthy and mastitic cows revealed the significance (P < 0.01) of udder health for EC, SCC and lactose. Of the different parameters that can distinguish between healthy and mastitic quarters or cows, EC could be used to classify 76% of quarters and 73% of cows correctly, while the lactose content permitted correct identification of 81% of quarters and 76% of cows. NAGase and pH could be used to determine the status of 73% and 61% of quarters, respectively. In general, the correlation observed in strippings was higher than in foremilk for almost all the variables studied. Surprisingly, EC, SCC, NAGase and lactose in milk from healthy quarters of mastitic cows (with at least one mastitic quarter) differed significantly (P < 0.05) from those from healthy quarters of cows with all four healthy quarters, indicating an inconsistent effect of mastitic quarters on neighbouring healthy quarters (quarter interdependence).

1. CARRIAGE HOUSE (left) AND SLAVE QUARTERS, SOUTH FRONT. A ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. CARRIAGE HOUSE (left) AND SLAVE QUARTERS, SOUTH FRONT. A kitchen was included in the quarters. - Charles Fraser House, Carriage House & Slave Quarters, 55 King Street, Charleston, Charleston County, SC

EMSL Quarterly Highlights Report: 1st Quarter, Fiscal Year 2009

DOE Office of Scientific and Technical Information (OSTI.GOV)

Showalter, Mary Ann; Kathmann, Loel E.; Manke, Kristin L.

2009-02-02

The EMSL Quarterly Highlights Report covers the science, staff and user recognition, and publication activities that occurred during the 1st quarter (October 2008 - December 2008) of Fiscal Year 2009.

Idaho National Laboratory Quarterly Occurrence Analysis for the 1st Quarter FY2017

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Lisbeth Ann

This report is published quarterly by the Idaho National Laboratory (INL) Quality and Performance Management Organization. The Department of Energy (DOE) Occurrence Reporting and Processing System (ORPS), as prescribed in DOE Order 232.2, “Occurrence Reporting and Processing of Operations Information,” requires a quarterly analysis of events, both reportable and not reportable, for the previous 12 months. This report is the analysis of 82 reportable events (13 from the 1st quarter (Qtr) of fiscal year (FY) 2017 and 68 from the prior three reporting quarters), as well as 31 other issue reports (including events found to be not reportable and Significantmore » Category A and B conditions) identified at INL during the past 12 months (seven from this quarter and 24 from the prior three quarters).« less

Notable deals in the pharmaceutical industry in the first quarter of 2017.

PubMed

Cruces, E

2017-06-01

During the first quarter of 2017, Cortellis Competitive Intelligence had 1,073 new deals added as part of its ongoing coverage of pharmaceutical licensing activity. This meant a slight increase on the last quarter (1,022) and a similar volume on the same quarter for the previous 1 year (1,141). However, this quarter showed a significant augment in deals worth more than USD 0.5 billion on the last quarter (17 vs. 12). This article will focus on highlighting a number of the most valuable and notable deals forged during the quarter, as well as a selection of deals from some of the most prolific deal makers. An update on milestone, options and terminated deals of significance will also be presented, along with an early outlook on the next quarter's pharmaceutical licensing activity.

Isochromatic photoelasticity fringe patterns of PMMA in various shapes and stress applications

NASA Astrophysics Data System (ADS)

Manjit, Y.; Limpichaipanit, A.; Ngamjarurojana, A.

2018-03-01

The research focuses on isochromatic photoelastic fringe patterns in solid materials by using reflection mode in dark field polariscope. The optical setup consists of light source, polarizers, quarter wave plates, 577 nm optical pass filter, compensator and digital camera system. The fringe patterns were produced on the sample and fractional / integer number of fringe order was observed using Babinet compensator and digital camera system. The samples were circular and rectangular shape of PMMA coated with silver spray and compressed by hydraulic system at the top and the bottom. The results of the isochromatic fringe pattern were analyzed in horizontal and vertical positions. It was found that force and the number of isochromatic photoelastic fringe order depended on shape of sample, which reflects stress distribution behavior.

The state of the great outdoors: charting recent trends, assessing funding needs, and understanding Americans' connection to nature.

PubMed

Walls, Margaret

2011-01-01

In 2008 and 2009, the Outdoor Resources Review Group (ORRG), a private bipartisan panel of recreation professionals, public officials, and conservation advocates, assessed priorities, challenges, and opportunities in managing the nation's land and water resources. The 17-member panel, with U.S. Senators Lamar Alexander (R-TN) and Jeff Bingaman (D-NM) as honorary co-chairs, held a series of public meetings and focused workshops that culminated in a report presented to the Secretary of the Interior. In support of the ORRG effort, my colleagues and I at Resources for the Future conducted an independent assessment of trends in demand and supply of open space, parks, and public lands-as well as funding and financing of these resources-during the past quarter-century.

Incorporating the whole-mount prostate histology reconstruction program Histostitcher into the extensible imaging platform (XIP) framework

NASA Astrophysics Data System (ADS)

Toth, Robert; Chappelow, Jonathan; Vetter, Christoph; Kutter, Oliver; Russ, Christoph; Feldman, Michael; Tomaszewski, John; Shih, Natalie; Madabhushi, Anant

2012-03-01

There is a need for identifying quantitative imaging (e.g. MRI) signatures for prostate cancer (CaP), so that computer-aided diagnostic methods can be trained to detect disease extent in vivo. Determining CaP extent on in vivo MRI is difficult to do; however, with the availability of ex vivo surgical whole mount histological sections (WMHS) for CaP patients undergoing radical prostatectomy, co-registration methods can be applied to align and map disease extent onto pre-operative MR imaging from the post-operative histology. Yet obtaining digitized images of WHMS for co-registration with the pre-operative MRI is cumbersome since (a) most digital slide scanners are unable to accommodate the entire section, and (b) significant technical expertise is required for whole mount slide preparation. Consequently, most centers opt to construct quartered sections of each histology slice. Prior to co-registration with MRI, however, these quartered sections need to be digitally stitched together to reconstitute a digital, pseudo WMHS. Histostitcheris an interactive software program that uses semi-automatic registration tools to digitally stitch quartered sections into pseudo WMHS. Histostitcherwas originally developed using the GUI tools provided by the Matlab programming interface, but the clinical use was limited due to the inefficiency of the interface. The limitations of the Matlab based GUI include (a) an inability to edit the fiducials, (b) the rendering being extremely slow, and (c) lack of interactive and rapid visualization tools. In this work, Histostitcherhas been integrated into the eXtensible Imaging Platform (XIP TM ) framework (a set of libraries containing functionalities for analyzing and visualizing medical image data). XIP TM lends the stitching tool much greater flexibility and functionality by (a) allowing interactive and seamless navigation through the full resolution histology images, (b) the ability to easily add, edit, or remove fiducials and annotations in order to register the quadrants and map the disease extent. In this work, we showcase examples of digital stitching of quartered histological sections into pseudo-WHMS using Histostitcher via the new XIP TM interface. This tool will be particularly useful in clinical trials and large cohort studies where a quick, interactive way of digitally reconstructing pseudo WMHS is required.

Adjustment Notes for Apprentice and Trainee Estimates: December Quarter 2016. Support Document

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2017

2017-01-01

Apprentice and trainee data are reported by the State and Territory Training Authorities to NCVER on a quarterly basis, starting at the September quarter of 1994. The set of data submitted that quarter is referred to as Collection 1. The sets of data submitted in subsequent quarters are referred to as Collection 2, Collection 3 and so on. NCVER…

Adjustment Notes for Apprentice and Trainee Estimates: September Quarter 2016. Support Document

ERIC Educational Resources Information Center

National Centre for Vocational Education Research (NCVER), 2017

2017-01-01

Apprentice and trainee data are reported by the State and Territory Training Authorities to NCVER on a quarterly basis, starting at the September quarter of 1994. The set of data submitted that quarter is referred to as Collection 1. The sets of data submitted in subsequent quarters are referred to as Collection 2, Collection 3 and so on. NCVER…

Design technology co-optimization for 14/10nm metal1 double patterning layer

NASA Astrophysics Data System (ADS)

Duan, Yingli; Su, Xiaojing; Chen, Ying; Su, Yajuan; Shao, Feng; Zhang, Recco; Lei, Junjiang; Wei, Yayi

2016-03-01

Design and technology co-optimization (DTCO) can satisfy the needs of the design, generate robust design rule, and avoid unfriendly patterns at the early stage of design to ensure a high level of manufacturability of the product by the technical capability of the present process. The DTCO methodology in this paper includes design rule translation, layout analysis, model validation, hotspots classification and design rule optimization mainly. The correlation of the DTCO and double patterning (DPT) can optimize the related design rule and generate friendlier layout which meets the requirement of the 14/10nm technology node. The experiment demonstrates the methodology of DPT-compliant DTCO which is applied to a metal1 layer from the 14/10nm node. The DTCO workflow proposed in our job is an efficient solution for optimizing the design rules for 14/10 nm tech node Metal1 layer. And the paper also discussed and did the verification about how to tune the design rule of the U-shape and L-shape structures in a DPT-aware metal layer.

X-ray microfocusing with off-axis ellipsoidal mirror

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yumoto, Hirokatsu, E-mail: yumoto@spring8.or.jp; Koyama, Takahisa; Matsuyama, Satoshi

2016-07-27

High-precision ellipsoidal mirrors for two-dimensionally focusing X-rays to nanometer sizes have not been realized because of technical problems in their fabrication processes. The objective of the present study is to develop fabrication techniques for ellipsoidal focusing mirrors in the hard-X-ray region. We design an off-axis ellipsoidal mirror for use under total reflection conditions up to the X-ray energy of 8 keV. We fabricate an ellipsoidal mirror with a surface roughness of 0.3 nm RMS (root-mean-square) and a surface figure error height of 3.0 nm RMS by utilizing a surface profiler and surface finishing method developed by us. The focusing propertiesmore » of the mirror are evaluated at the BL29XUL beamline in SPring-8. A focusing beam size of 270 nm × 360 nm FWHM (full width at half maximum) at an X-ray energy of 7 keV is observed with the use of the knife-edge scanning method. We expect to apply the developed fabrication techniques to construct ellipsoidal nanofocusing mirrors.« less

The challenges encountered in the integration of an early test wafer surface scanning inspection system into a 450mm manufacturing line

NASA Astrophysics Data System (ADS)

Lee, Jeffrey; McGarvey, Steve

2013-04-01

The introduction of early test wafer (ETW) 450mm Surface Scanning Inspection Systems (SSIS) into Si manufacturing has brought with it numerous technical, commercial, and logistical challenges on the path to rapid recipe development and subsequent qualification of other 450mm wafer processing equipment. This paper will explore the feasibility of eliminating the Polystyrene Latex Sphere deposition process step and the subsequent creation of SSIS recipes based upon the theoretical optical properties of both the SSIS and the process film stack(s). The process of Polystyrene Latex Sphere deposition for SSIS recipe generation and development is generally accepted on the previous technology nodes for 150/200/300mm wafers. PSL is deposited with a commercially available deposition system onto a non-patterned bare Si or non-patterned filmed Si wafer. After deposition of multiple PSL spots, located in different positions on a wafer, the wafer is inspected on a SSIS and a response curve is generated. The response curve is based on the the light scattering intensity of the NIST certified PSL that was deposited on the wafer. As the initial 450mm Si wafer manufacturing began, there were no inspection systems with sub-90nm sensitivities available for defect and haze level verification. The introduction of a 450mm sub-30nm inspection system into the manufacturing line generated instant challenges. Whereas the 450mm wafers were relatively defect free at 90nm, at 40nm the wafers contained several hundred thousand defects. When PSL was deposited onto wafers with these kinds of defect levels, PSL with signals less than the sub-90nm defects were difficult to extract. As the defectivity level of the wafers from the Si suppliers rapidly improves the challenges of SSIS recipe creation with high defectivity decreases while at the same time the cost of PSL deposition increases. The current cost per wafer is fifteen thousand dollars for a 450mm PSL deposition service. When viewed from the standpoint of the generations of hundreds of SSIS recipes for the global member companies of ISMI, it is simply not economically viable to create all recipes based on PSL based light scattering response curves. This paper will explore the challenges/end results encountered with the PSL based SSIS recipe generation and compare those against the challenges/end results of SSIS recipes generated based strictly upon theoretical Bidirectional reflectance distribution function (BRDF) light scattering modeling. The BRDF modeling will allow for the creation of SSIS recipes without PSL deposition, which is greatly appealing for a multitude of both technical and commercial considerations. This paper will also explore the technical challenges of SSIS recipe generation based strictly upon BRDF modeling.

Notable licensing deals in the biopharma industry in the second quarter of 2017.

PubMed

D'Souza, P

2017-08-01

During the second quarter of 2017, Cortellis Competitive Intelligence added 967 new licensing deals (excluding mergers and acquisition deals) as part of its ongoing coverage of pharmaceutical licensing activity. This meant an 8% decrease on the previous quarter (1,050) and a 3% decrease from the same quarter in 2016 (993). This quarter also showed a significant decline in the number of deals worth more than USD 0.5 billion from the last quarter (7 vs. 17). This article will highlight a number of the most valuable and notable deals forged during the quarter, as well as a selection of deals from some of the most prolific deal makers in the life sciences. An update on milestone, options and terminated deals of significance will also be presented, along with an early outlook on the next quarter's pharmaceutical licensing activity.

Integrated Data Collection Analysis (IDCA) Program — IDCA Quarterly Program Review, September 14 and 15, 2010

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sandstrom, Mary M.; Brown, Geoffrey W.; Warner, Kirstin F.

The IDCA conducted a program review at Los Alamos National Laboratory, September 14 and 15, 2010. The review was divided into three parts: 1) an update on the current status of the program, 2) an information exchange and discussion on technical details for current issues and future planning, and 3) a tour of the SSST testing facilities at LANL. The meeting started with an update from DHS by Laura Parker and a restating of some of the objectives of the Proficiency Test of which the IDCA is currently engaged. This update was followed by a discussion of some high levelmore » programmatic issues particularly about ways of communicating the overall goals of the IDCA to non-technical representatives. The final topic focused on the difficulty of releasing information, including the DHS approval process, ITAR, and open publication. Next JGR presented a technical summary of accomplishments, schedule, milestones, and future directions. These key points made were: 1) about 1/3 of the materials have been tested, 2) some participants are behind others causing a lag in report writing, 3) method reports have been assigned to various participants to speed up the process of reporting, 4) the SSST Compendium needs reformatting and restructuring, and 5) the Compendium needs a web site to house with access control. After the technical update, some of the Proficiency Test results were shown comparing data from the various laboratories. These results included comparisons of the RDX standard, KC/sugar mixtures (-100 mesh and as received), KC/dodecane, KP/Al, and KP/C. Impact, friction, ESD, and DSC results were the focus. All the participants were involved in these discussions. This report includes summary notes, presentations, and explanatory information.« less

Decontamination systems information and research programs. Quarterly report, July 1--August 31, 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1997-07-01

The US contains numerous hazardous waste sites. Many sites are on private land near operating units of various companies. An effort is being made to determine the conditions under which such sites can be remediated voluntarily. The objective of the project will be to first assess the interest and willingness of industry in the Kanawha River Valley, WV to participate in discussions that would lead toward voluntary cleanup activities. The second will be to implement the activities agreed upon by the interested parties. The project will first involve individual discussions with the industrial, government, and other organized groups in themore » area. These discussions will help determine the feasibility of organizing voluntary efforts. If the discussions indicate that conditions may be favorable for developing individual or group voluntary cleanup projects, a working group will be convened to establish the environmental goals of the project as well as the technical approach for achieving those goals. The projects for the 1996 WVU Cooperative Agreement are categorized into three task focus areas: Task 1.0 Contaminant Plume Containment and Remediation, Task 2.0 Cross Cutting Innovative Technologies, and Task 3.0 Small Business Support Program. Summaries of the accomplishments for the subtasks reporting under these categories during the third quarter, 1 July 96 through 30 September 96, are presented.« less

Biomass power for rural development. Technical progress report, October 1--December 31, 1997

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neuhauser, E.

The focus of the DOE/USDA sponsored biomass power for rural development project is to develop commercial energy crops for power generation by the year 2000. The New York based Salix Consortium project is a multi-partner endeavor, implemented in three stages. Phase-1, Final Design and Project Development, will conclude with the preparation of construction and/or operating permits, feedstock production plans, and contracts ready for signature. Field trials of willow (Salix) have been initiated at several locations in New York (Tully, Lockport, King Ferry, La Fayette, Massena, and Himrod) and co-firing tests are underway at Greenidge Station (NYSEG) and Dunkirk Station (NMPC).more » Phase-2 of the project will focus on scale-up of willow crop acreage, construction of co-firing facilities at Dunkirk Station (NMPC), and final modifications for Greenidge Station. Cofiring willow is also under consideration for GPU`s Seward Station where testing is underway. There will be an evaluation of the energy crop as part of the gasification trials occurring at BED`s McNeill Power Station. Phase-3 will represent fullscale commercialization of the energy crop and power generation on a sustainable basis. During the fourth quarter of 1997 the Consortium submitted a Phase-2 proposal. A few of the other more important milestones are outlined below. The first quarter of 1998 will be dominated by pre-planting activity in the spring.« less

(Study of the behavioral and biological effects of high intensity 60 Hz electric fields): Quarterly technical progress report No. 29

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orr, J.L.

1989-07-14

Activities this quarter involved all phases of the project plus a meeting of the Joint Committee in Tokyo. Detailed mapping of the exposure facility is scheduled to be completed during the week of August 14, 1989. Both electric and magnetic fields should be available for tests of the components of the tether and blood sampling system for the neuroendocrine pilot study in September 1989. The groups for the social behavior study are stabilizing appropriately. Details on the formation of the groups and their status has been provided. Dr. Coelho has included information related to aspects of the social experiment rangingmore » from age estimation in baboons through the cardiovascular consequences of psychosocial stress. In addition, a draft manuscript is included on the data from the previous experiments which describes the effects of 30 and 60 kV/m electric fields on the social behavior of baboons. Tests of the blood handling procedures and analysis methods have been completed. With the exception of the catecholamine analyses, the handling procedures and variability in replicate measurements are satisfactory. Logistic and practical considerations now weigh strongly against including the analysis of the blood samples for catecholamines. Preliminary tests indicate that a sampling procedure which will work for the other compounds is probably not satisfactory for the catecholamines.« less

REBL: design progress toward 16 nm half-pitch maskless projection electron beam lithography

NASA Astrophysics Data System (ADS)

McCord, Mark A.; Petric, Paul; Ummethala, Upendra; Carroll, Allen; Kojima, Shinichi; Grella, Luca; Shriyan, Sameet; Rettner, Charles T.; Bevis, Chris F.

2012-03-01

REBL (Reflective Electron Beam Lithography) is a novel concept for high speed maskless projection electron beam lithography. Originally targeting 45 nm HP (half pitch) under a DARPA funded contract, we are now working on optimizing the optics and architecture for the commercial silicon integrated circuit fabrication market at the equivalent of 16 nm HP. The shift to smaller features requires innovation in most major subsystems of the tool, including optics, stage, and metrology. We also require better simulation and understanding of the exposure process. In order to meet blur requirements for 16 nm lithography, we are both shrinking the pixel size and reducing the beam current. Throughput will be maintained by increasing the number of columns as well as other design optimizations. In consequence, the maximum stage speed required to meet wafer throughput targets at 16 nm will be much less than originally planned for at 45 nm. As a result, we are changing the stage architecture from a rotary design to a linear design that can still meet the throughput requirements but with more conventional technology that entails less technical risk. The linear concept also allows for simplifications in the datapath, primarily from being able to reuse pattern data across dies and columns. Finally, we are now able to demonstrate working dynamic pattern generator (DPG) chips, CMOS chips with microfabricated lenslets on top to prevent crosstalk between pixels.

42 CFR 433.10 - Rates of FFP for program services.

Code of Federal Regulations, 2013 CFR

2013-10-01

...; (B) 95 percent, for calendar quarters in CY 2017; (C) 94 percent, for calendar quarters in CY 2018... quarters in CY 2018; and (F) 100 percent, for calendar quarters in CY 2019 and all subsequent calendar...

Installation of a stoker-coal preparation plant in Krakow, Poland. Quarterly technical progress report No. 4, January--March, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rozelle, P.

1996-01-01

This report describes the progress made during this reporting period of a two year project to demonstrate that the air pollution from a traveling-grate stoker being used to heat water at a central heating plant in Krakow, Poland can be reduced significantly by (1) substituting the unwashed, unsized coal currently being used with a mechanically cleaned, double-sized stoker fuel and by (2) optimizing the operating parameters of the stoker. It is anticipated that these improvements will prove to be cost-effective and hence will be adopted by the other central heating plants in Krakow and ideally, throughout Eastern European cities wheremore » coal continues to be the primary source of fuel. EFH Coal Company has formed a partnership with two Polish institutions -- MPEC, a central heating company in Krakow, and Naftokrak-Naftobudowa, preparation plant designers and fabricators-for the execution of this effort. Five potential candidate sources have been located and contracts for coal deliveries should be executed early next quarter. TInitial delays in formalizing the EFH/Polish Partners agreement delayed finalizing the coal supply contracts and hence, precluded collecting the Polish coal samples for characterization and combustion performance studies. Work on this Task will be initialed next quarter after the raw coal supply contracts are executed. A conceptual design for a plant to wash 25mm x 0 raw coal fines at a need rate of 300 mtph was completed. This plant will receive raw coals ranging in ash content from 20 to 30 percent and produce a compliance coal containing about 1 percent ash, 0.8 percent sulfur and 27, 840 KJ/kg (12,000 Btu/lb). A heavy-media cyclone will be used to wash the 20mm x 1mm stoker coal. Discussions with financial institutions regarding the cost of producing a quality stoker coal in Poland and A for identifying sources of private capital to help cost share the project continued.« less

Catalysts and process developments for two-stage liquefaction. Third quarterly technical progress report No. 44, April 1, 1991--June 30, 1991

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cronauer, D.C.; Swanson, A.J.; Sajkowski, D.J.

Research under way in this project centers upon developing and evaluating catalysts and process improvements for coal liquefaction in the two-stage close-coupled catalytic process. As documented in the previous quarterly report (Task 3.1), there was little advantage for presoaking Black Thunder coal or Martin Lake lignite in a hydrogen-donor solvent, such as tetralin, at temperatures up to 600{degrees}F prior to liquefaction at higher temperatures. The amount of decarboxylation that occurred during the presoaking of Black Thunder coal or Martin Lake lignite in tetralin in the temperature range of 400 to 600{degrees}F was also relatively small. Further experimentation was undertaken inmore » a continuous flow unit with Black Thunder coal, where the primary goal was to determine the extent of decarboxylation and changes in the structure of the unconverted coal samples. The preliminary results indicated little conversion of the feed coal to THF solubles at 600{degrees}F, although the conversion did increase with increasing temperature up to 24% at 700{degrees}F. The level of decarboxylation was also low at the above reaction temperatures. Thus, presoaking in a coal-derived solvent or even tetralin does not seem to be an effective means to achieve decarboxylation. A suitable sample of Illinois No. 6 coal was received and tested for liquefaction. The batch liquefaction showed that this sample had good reactivity. The continuous liquefaction test was done in a two-stage unit with AMOCAT{trademark}-1C catalyst in both reactors. A significant amount of resid was produced throughout this three-week run. As the catalyst aged, the distillate production decreased and its product quality got worse. The feedstock liquefaction studies for the three feedstocks (Black Thunder subbituminous coal, Martin Lake lignite, and Illinois No. 6 coal) have been completed, and their results will be compared in a subsequent quarterly report.« less

Experimental intramammary inoculation with Mycoplasma bovis in vaccinated and unvaccinated cows: effect on milk production and milk quality.

PubMed Central

Boothby, J T; Jasper, D E; Thomas, C B

1986-01-01

The effect of vaccination on milk production was evaluated in vaccinated and control cows experimentally challenged in two of four quarters with live Mycoplasma bovis. During the first three weeks after experimental challenge, six of eight unchallenged quarters on vaccinated cows and seven of eight unchallenged quarters on control cows became infected. Most of these quarters secreted normal milk, with negative California Mastitis Test scores and maintained normal milk production throughout most of the study (although some quarters on control cows remained infected). All challenged quarters became infected, had strong California Mastitis Test reactions, and had a drastic (greater than 85%) loss in milk production. Thereafter, four of eight challenged quarters on control cows remained infected, had mostly positive California Mastitis Test scores, produced mostly normal-appearing milk, and recovered some productive capabilities. By the end of the study no M. bovis could be recovered from challenged quarters on vaccinated cows and the milk appeared mostly normal. The California Mastitis Test scores on these quarters, however, remained elevated and milk production remained very low. PMID:3756674

Cultural and Technical Evaluation of Heating Alternatives to Improve Indoor Air Quality on the Navajo Nation

EPA Science Inventory

In the Navajo Nation it is estimated that 62% of households use wood as their primary means of heating1. A 2010 study by the U.S. Geological Survey (USGS) and Diné College found that in Shiprock, NM, the largest town in the Navajo Nation (pop. = 8,300)2, heating is often w...

["TECHNIKA I NAUKA" ["SCIENCE AND TECHNOLOGY"] (1958-)--MAGAZINE OF THE ASSOCIATION OF POLISH ENGINEERS IN GREAT BRITAIN].

PubMed

Chwastyk-Kowalczyk, Jolanta

2015-01-01

This article presents the history of establishment, functioning and the role of "Science and Technology"--quarterly of the Association of Polish Engineers in Great Britain--in shaping Polish technical thought in the environment of Polish engineers and technicians living in exile. The analysis of the content of the journal published in London in the years 1958-2008 made it evident that this official scientific organ of Polish technical intelligentsia edited in 500 copies reaches members of engineering, technical and scientific milieu across many continents. Despite the fact that Polish language dominates in the articles and thanks to the interdisciplinary character of their content - science and technology, biology, the humanities, sociology and others--the journal makes it possible for the reader to participate in an intellectual adventure. "Science and Technology" was created in 1958 on the initiative of Eng. Prof. Roman Wajda in Great Britain, with support of other Polish technical associations abroad, and embraced the achievements and organisational life of the Polish technical milieu dispersed around the world. On the basis of the London Society's archive materials and old annual volumes of the journal, the author listed editors-in-chief, composition of editorial committees, collaborators, determined editing costs, changeable periodicity, successive print shops, seats of editorial office that always followed the Association in Great Britain. She also showed the effort of a handful of members of editorial committees, working on a voluntary basis to obtain materials for the journal; the role of the journal linking Polish engineers and technicians in exile and its function as a link with the Country, as well as its role in the sphere of information and propaganda. Finally, the author made an analysis of the journal's content, focusing on categories of articles published in "Science and Technology" in the years 1958-2008. Methods used by the author in the article: archival, analysis of the press content: qualitative and quantitative.

The magic of 4X mask reduction

NASA Astrophysics Data System (ADS)

Lercel, Michael

2006-06-01

Although changing the mask reduction factor from 4X to a larger value offers several technical advantages, previous attempts to enact this change have not identified enough clear technical advantages to overcome the impact to productivity. Improvements in mask manufacturing, mask polarization effects, and optics cost have not been thought to be sufficient reason to accept a reduced throughput and field size. This paper summarizes the latest workshop and discussion revisiting the mask reduction factor for 32nm half-pitch lithography with hyper-numerical aperture (NA) optical or extreme ultraviolet lithography (EUVL). The workshop consensus was strongly in favor of maintaining the current magnification ratio and field size as long as mask costs can be contained.

Gas turbine engines and transmissions for bus demonstration programs. Technical status report, 30 April 1979-31 July 1979

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nigro, D.N.

1979-07-01

The quarterly status report covers the period from 30 April 1979 through 31 July 1979 and is a summary of DDA activities for the effort performed on the procurement and delivery of eleven (11) Allison GT 404-4 gas turbine engines and five (5) HT740CT and six (6) V730CT Allison automatic transmissions and the required associated software. The contract requires the delivery of eleven (11) Allison GT 404-4 Industrial Gas Turbine Engines and five (5) HT740CT and six (6) V730CT Allison Automatic Transmissions for the Greyhound and Transit Coaches, respectively. In addition, software items such as cost reports, technical reports, installationmore » drawings, acceptance test data and parts lists are required. A recent decision by the DOE will modify the build configuration for the last four (4) Transit Coach engines. It was decided by the DOE at a meeting in Washington, DC on March 28, 1979 with representatives from DDA, NASA/LeRC, JPL and Booz-Allen and Hamilton that these engines will be built with ceramic regenerators. (TFD)« less

Development of optical sciences in Poland

NASA Astrophysics Data System (ADS)

Romaniuk, Ryszard S.

2013-10-01

Research and technical communities for optics, photonics and optoelectronics is grouped in this country in several organizations and institutions. These are: Photonics Society of Poland (PSP), Polish Committee of Optoelectronics of SEP, Photonics Section of KEiT PAN, Laser Club at WAT, and Optics Section of PTF. Each of these communities keeps slightly different specificity. PSP publishes a quarterly journal Photonics Letters of Poland, stimulates international cooperation, and organizes conferences during Industrial Fairs on Innovativeness. PKOpto SEP organizes didactic diploma competitions in optoelectronics. KEiT PAN takes patronage over national conferences in laser technology, optical fiber technology and communications, and photonics applications. SO-PTF has recently taken a decision to organize a cyclic event "Polish Optical Conference". The third edition of this conference PKO'2013 was held in Sandomierz on 30.06-04.07.2013. The conference scientific and technical topics include: quantum and nonlinear optics, photon physics, optic and technology of lasers and other sources of coherent radiation, optoelectronics, optical integrated circuits, optical fibers, medical optics, instrumental optics, optical spectroscopy, optical metrology, new optical materials, applications of optics, teaching in optics. This paper reviews chosen works presented during the III Polish Optical Conference (PKO'2013), representing the research efforts at different national institutions.

1. GENERAL VIEW OF SLAVE QUARTERS No. 2 (right). Located ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. GENERAL VIEW OF SLAVE QUARTERS No. 2 (right). Located north of main house. The building at left is Slave Quarters No. 1 (HABS No. VA-1233 C) - Westend, Slave Quarters No. 2, Route 638 vicinity, Trevilians, Louisa County, VA

Idaho National Laboratory Quarterly Occurrence Analysis - 3rd Quarter FY-2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Lisbeth Ann

This report is published quarterly by the Idaho National Laboratory (INL) Quality and Performance Management Organization. The Department of Energy (DOE) Occurrence Reporting and Processing System (ORPS), as prescribed in DOE Order 232.2, “Occurrence Reporting and Processing of Operations Information,” requires a quarterly analysis of events, both reportable and not reportable, for the previous 12 months. This report is the analysis of 73 reportable events (23 from the 3rd Qtr FY-16 and 50 from the prior three reporting quarters), as well as 45 other issue reports (including events found to be not reportable and Significant Category A and B conditions)more » identified at INL during the past 12 months (16 from this quarter and 29 from the prior three quarters).« less

Idaho National Laboratory Quarterly Occurrence Analysis - 1st Quarter FY 2016

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mitchell, Lisbeth Ann

This report is published quarterly by the Idaho National Laboratory (INL) Quality and Performance Management Organization. The Department of Energy (DOE) Occurrence Reporting and Processing System (ORPS), as prescribed in DOE Order 232.2, “Occurrence Reporting and Processing of Operations Information,” requires a quarterly analysis of events, both reportable and not reportable, for the previous 12 months. This report is the analysis of 74 reportable events (16 from the 1st Qtr FY-16 and 58 from the prior three reporting quarters), as well as 35 other issue reports (including events found to be not reportable and Significant Category A and B conditions)more » identified at INL during the past 12 months (15 from this quarter and 20 from the prior three quarters).« less

Feasibility Study to Identify Potential Reductions in Energy Use in Tribal Buildings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stevens, Willie

Under this project, the Confederated Salish and Kootenai Tribes (CSKT) assessed the technical and economic feasibility of energy efficiency improvements to existing Tribally-owned buildings. The feasibility study followed a systematic approach in identifying, selecting, and ranking recommended measures, recognizing that the appropriateness of a measure would depend not only on technical issues but also on institutional and organizational issues, such as financing options and occupant requirements. The completed study provided the Tribes with the information needed to commit necessary resources to reduce the energy use and cost in approximately 40 Tribal buildings, including the changes that may be needed inmore » each facility’s operation and maintenance and personnel requirements. It also presented an economic analysis of energy-efficiency capital improvements and an annotated list of financing options and possible funding sources for implementation and an overall strategy for implementation. This project was located in various Tribal communities located throughout the Flathead Indian Reservation in Western Montana. Notice: The following is a compilation of Annual Program Review Presentations, Award Modifications, and Quarterly Progress Reports submitted to the Department of Energy’s (DOE) Office of Indian Energy Policy and Programs by the Confederated Salish and Kootenai Tribes under agreement DE-EE0005171. This report covers project activities from September 30, 2011 through December 31, 2014 and has been uploaded to OSTI by DOE as a substitute for the required Final Technical Report which was not received by DOE from the project recipient.« less

Investigation of syngas interaction in alcohol synthesis catalysts. Quarterly technical progress report, September 1, 1993--January 31, 1994

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-02-10

The project establishes the necessary experiment and laboratory facilities at Xavier University. This phase of the work has taken a considerable amount of time, due to the limited laboratory space and the involved administrative policies and procedures in procuring the necessary chemicals, glassware and auxiliary supplies. Though there still remain some minor problems with space, the laboratory is now equipped for preparation of catalysts. During this period, the authors focused their attention toward analyzing the magnetic nature of extensively used trimetallic catalyst system Cu-Co-Cr for the production of higher alcohols. The authors decided to investigate the effect of method ofmore » preparation and intermetallic ratio on the magnetic behavior of the system.« less

Novel carbon-ion fuel cells. Quarterly technical report No. 9, October 1, 1995--December 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cocks, F.H.

1995-12-31

This report presents research to develop an entirely new, fundamentally different class of fuel cell using a solid electrolyte that transports carbon ions. This fuel cell would use solid carbon dissolved in molten metal as a fuel reservoir and anode; expensive gaseous or liquid fuel would not be required. Thermodynamic factors favor a carbon-ion fuel cell over other fuel cell designs: a combination of enthalpy, entropy, and Gibbs free energy makes the reaction of solid carbon and oxygen very efficient, and the entropy change allows this efficiency to slightly increase at high temperatures. The high temperature exhaust of the fuelmore » cell would make it useful as a ``topping cycle``, to be followed by conventional steam turbine systems.« less

Novel carbon-ion fuel cells. Quarterly technical report, April--June 1996

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cocks, F.H.

1996-11-01

This report presents research to develop a new type of of fuel cell using a solid electrolyte that transports carbon ions. This new class of fuel cell would use solid C dissolved in molten metal (carbide) as a fuel reservoir and anode; thus expensive gas or liquid fuel would not be required. Thermodynamic efficiency of carbon-ion fuel cells is reviewed, as are electrolyte crystal structures (oxide and fluorite carbides). The sequence of laboratory research procedures for developing a solid C-ion electrolyte and to determine the ionic conductivity of C ions therein is outlined; results of the laboratory research to datemore » are summarized, including XRD analysis of crystal structures and transition temperatures of carbides (La, Ce, Be, Al) and SIMS of carbon isotopes.« less

Mitigation of biofouling using coatings: Year 2. Quarterly progress report No. 1. Calspan report 6782-M-5

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyer, A.E.; King, R.W.

1982-01-15

Objectives of this project are to evaluate benefits associated with control of the surface energetic properties of materials used in heat exchangers; and to identify preferred ranges of these surface conditions that minimize deposits of biological fouling known to deteriorate heat exchange efficiencies in seawater, brackish water, and freshwater systems. The technical approach employed uses special diagnostic plates in novel flow cells where fluid flow conditions can be well-controlled, modifying the surface chemistry and surface energy of the plates with very thin coatings and examining the earliest events of biofouling caused by macromolecules and microbial organisms. For the present phasemore » of the project (Year 2), attention will be focussed on biofouling in a freshwater/brackish water system.« less

[The spectrogram characteristics of organic blue-emissive light-emitting excitated YAG : Ce phosphor].

PubMed

Xi, Jian-Fei; Zhang, Fang-Hui; Mu, Qiang; Zhang, Mai-Li

2011-09-01

It is demonstrated that the panchromatic luminescence devices with organic blue-emissive light-emitting was fabricated. This technique used down conversion, which was already popular in inorganic power LEDs to obtain white light emission. A blue OLED device with a configuration of ITO/2T-NATA (30 nm)/AND : TBPe (50 Wt%, 40 nm)/Alq3 (100 nm)/LiF(1 nm)/Al(100 nm) was prepared via vacuum deposition process, and then coated with YAG : Ce phosphor layers of different thicknesses to obtain a controllable and uniform shape while the CIE coordinates were fine tuned. This development not only decreased steps of technics and degree of difficulty, but also applied the mature technology of phosphor. The results showed that steady spectrogram was obtained in the devices with phosphor, with a best performance of a maximum luminance of 13 840 cd x m(-2) which was about 2 times of that of the devices without phosphor; a maximum current efficiency of 17.3 cd x A(-1) was increased more two times more than the devices without phosphor. The emission spectrum could be adjusted by varying the concentration and thickness of the phosphor layers. Absoulte spectrogram of devices was in direct proportion with different driving current corresponding.

A novel double patterning approach for 30nm dense holes

NASA Astrophysics Data System (ADS)

Hsu, Dennis Shu-Hao; Wang, Walter; Hsieh, Wei-Hsien; Huang, Chun-Yen; Wu, Wen-Bin; Shih, Chiang-Lin; Shih, Steven

2011-04-01

Double Patterning Technology (DPT) was commonly accepted as the major workhorse beyond water immersion lithography for sub-38nm half-pitch line patterning before the EUV production. For dense hole patterning, classical DPT employs self-aligned spacer deposition and uses the intersection of horizontal and vertical lines to define the desired hole patterns. However, the increase in manufacturing cost and process complexity is tremendous. Several innovative approaches have been proposed and experimented to address the manufacturing and technical challenges. A novel process of double patterned pillars combined image reverse will be proposed for the realization of low cost dense holes in 30nm node DRAM. The nature of pillar formation lithography provides much better optical contrast compared to the counterpart hole patterning with similar CD requirements. By the utilization of a reliable freezing process, double patterned pillars can be readily implemented. A novel image reverse process at the last stage defines the hole patterns with high fidelity. In this paper, several freezing processes for the construction of the double patterned pillars were tested and compared, and 30nm double patterning pillars were demonstrated successfully. A variety of different image reverse processes will be investigated and discussed for their pros and cons. An economic approach with the optimized lithography performance will be proposed for the application of 30nm DRAM node.

77 FR 51705 - Rescission of Quarterly Financial Reporting Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-27

... No. FMCSA-2012-0020] RIN-2126-AB48 Rescission of Quarterly Financial Reporting Requirements AGENCY...: FMCSA withdraws its June 27, 2012, direct final rule eliminating the quarterly financial reporting... future proposing the elimination of the quarterly financial reporting requirements for Form QFR and Form...

Teaching Physics and Feeling Good about It.

ERIC Educational Resources Information Center

Prokop, Charles F.

1988-01-01

Describes a high school physics teaching sequence including more modern topics. The first quarter covers cosmology, astronomy, optics, wave mechanics, relativity, gravity, and quantum theory. The second quarter covers classical mechanics. The third quarter covers electromagnetism and electronics. The fourth quarter consists of thermodynamics and…

10 CFR 34.29 - Quarterly inventory.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 10 Energy 1 2012-01-01 2012-01-01 false Quarterly inventory. 34.29 Section 34.29 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.29 Quarterly inventory. (a) Each licensee shall conduct a quarterly...

10 CFR 34.29 - Quarterly inventory.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 10 Energy 1 2013-01-01 2013-01-01 false Quarterly inventory. 34.29 Section 34.29 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.29 Quarterly inventory. (a) Each licensee shall conduct a quarterly...

10 CFR 34.29 - Quarterly inventory.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 10 Energy 1 2014-01-01 2014-01-01 false Quarterly inventory. 34.29 Section 34.29 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.29 Quarterly inventory. (a) Each licensee shall conduct a quarterly...

10 CFR 34.29 - Quarterly inventory.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 10 Energy 1 2011-01-01 2011-01-01 false Quarterly inventory. 34.29 Section 34.29 Energy NUCLEAR REGULATORY COMMISSION LICENSES FOR INDUSTRIAL RADIOGRAPHY AND RADIATION SAFETY REQUIREMENTS FOR INDUSTRIAL RADIOGRAPHIC OPERATIONS Equipment § 34.29 Quarterly inventory. (a) Each licensee shall conduct a quarterly...

77 FR 39447 - Revisions to Electric Quarterly Report Filing Process

Federal Register 2010, 2011, 2012, 2013, 2014

2012-07-03

... Quarterly Report Filing Process AGENCY: Federal Energy Regulatory Commission, DOE. ACTION: Notice of... Rule which governs the filing of Electric Quarterly Reports (EQRs), to change the process for filing... Regulatory Commission (Commission) proposes changes to the method for filing Electric Quarterly Reports (EQRs...

Interpretation of stable isotope, denitrification, and groundwater age data for samples collected from Sandia National Laboratories /New Mexico (SNL/NM) Burn Site Groundwater Area of Concern

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madrid, V.; Singleton, M. J.; Visser, A.

This report combines and summarizes results for two groundwater-sampling events (October 2012 and October/November 2015) from the Sandia National Laboratories/New Mexico (SNL/NM) Burn Site Groundwater (BSG) Area of Concern (AOC) located in the Lurance Canyon Arroyo southeast of Albuquerque, NM in the Manzanita Mountains. The first phase of groundwater sampling occurred in October 2012 including samples from 19 wells at three separate sites that were analyzed by the Environmental Radiochemistry Laboratory at Lawrence Livermore National Laboratory as part of a nitrate Monitored Natural Attenuation (MNA) evaluation. The three sites (BSG, Technical Area-V, and Tijeras Arroyo) are shown on the regionalmore » hydrogeologic map and described in the Sandia Annual Groundwater Monitoring Report. The first phase of groundwater sampling included six monitoring wells at the Burn Site, eight monitoring wells at Technical Area-V, and five monitoring wells at Tijeras Arroyo. Each groundwater sample was analyzed using the two specialized analytical methods, age-dating and denitrification suites. In September 2015, a second phase of groundwater sampling took place at the Burn Site including 10 wells sampled and analyzed by the same two analytical suites. Five of the six wells sampled in 2012 were resampled in 2015. This report summarizes results from two sampling events in order to evaluate evidence for in situ denitrification, the average age of the groundwater, and the extent of recent recharge of the bedrock fracture system beneath the BSG AOC.« less

26 CFR 1.461-1 - General rule for taxable year of deduction.

Code of Federal Regulations, 2010 CFR

2010-04-01

... quarter, 1964 Apr. 1 300,000 2d quarter, 1964 July 1 300,000 3d quarter, 1964 Oct. 1 300,000 4th quarter... of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and on GPO...

10 CFR 34.29 - Quarterly inventory.

Code of Federal Regulations, 2010 CFR

2010-01-01

... RADIOGRAPHIC OPERATIONS Equipment § 34.29 Quarterly inventory. (a) Each licensee shall conduct a quarterly physical inventory to account for all sealed sources and for devices containing depleted uranium received... 10 Energy 1 2010-01-01 2010-01-01 false Quarterly inventory. 34.29 Section 34.29 Energy NUCLEAR...

19 CFR 159.34 - Certified quarterly rate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... TREASURY (CONTINUED) LIQUIDATION OF DUTIES Conversion of Foreign Currency § 159.34 Certified quarterly rate. (a) Countries for which quarterly rate is certified. For the currency of each of the following... York for such foreign currency for a day in that quarter: Australia, Austria, Belgium, Brazil, Canada...

78 FR 59093 - Quarterly Rail Cost Adjustment Factor

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-25

...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2013 rail cost adjustment factor (RCAF) and cost index filed by the Association of American Railroads. The fourth quarter 2013 RCAF...

49 CFR 228.101 - Distance requirement for employee sleeping quarters; definitions used in this subpart.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 4 2012-10-01 2012-10-01 false Distance requirement for employee sleeping... OF SERVICE OF RAILROAD EMPLOYEES; RECORDKEEPING AND REPORTING; SLEEPING QUARTERS Construction of Railroad-Provided Sleeping Quarters § 228.101 Distance requirement for employee sleeping quarters...

49 CFR 228.101 - Distance requirement for employee sleeping quarters; definitions used in this subpart.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 49 Transportation 4 2014-10-01 2014-10-01 false Distance requirement for employee sleeping... OF SERVICE OF RAILROAD EMPLOYEES; RECORDKEEPING AND REPORTING; SLEEPING QUARTERS Construction of Railroad-Provided Sleeping Quarters § 228.101 Distance requirement for employee sleeping quarters...

49 CFR 228.101 - Distance requirement for employee sleeping quarters; definitions used in this subpart.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 4 2013-10-01 2013-10-01 false Distance requirement for employee sleeping... OF SERVICE OF RAILROAD EMPLOYEES; RECORDKEEPING AND REPORTING; SLEEPING QUARTERS Construction of Railroad-Provided Sleeping Quarters § 228.101 Distance requirement for employee sleeping quarters...

26 CFR 1.461-1 - General rule for taxable year of deduction.

Code of Federal Regulations, 2014 CFR

2014-04-01

... quarter, 1964 Apr. 1 300,000 2d quarter, 1964 July 1 300,000 3d quarter, 1964 Oct. 1 300,000 4th quarter... of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www...

26 CFR 1.461-1 - General rule for taxable year of deduction.

Code of Federal Regulations, 2011 CFR

2011-04-01

... quarter, 1964 Apr. 1 300,000 2d quarter, 1964 July 1 300,000 3d quarter, 1964 Oct. 1 300,000 4th quarter... of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www...

26 CFR 1.461-1 - General rule for taxable year of deduction.

Code of Federal Regulations, 2012 CFR

2012-04-01

... quarter, 1964 Apr. 1 300,000 2d quarter, 1964 July 1 300,000 3d quarter, 1964 Oct. 1 300,000 4th quarter... of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www...

26 CFR 1.461-1 - General rule for taxable year of deduction.

Code of Federal Regulations, 2013 CFR

2013-04-01

... quarter, 1964 Apr. 1 300,000 2d quarter, 1964 July 1 300,000 3d quarter, 1964 Oct. 1 300,000 4th quarter... of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www...

Nano-Computed Tomography: Technique and Applications.

PubMed

Kampschulte, M; Langheinirch, A C; Sender, J; Litzlbauer, H D; Althöhn, U; Schwab, J D; Alejandre-Lafont, E; Martels, G; Krombach, G A

2016-02-01

Nano-computed tomography (nano-CT) is an emerging, high-resolution cross-sectional imaging technique and represents a technical advancement of the established micro-CT technology. Based on the application of a transmission target X-ray tube, the focal spot size can be decreased down to diameters less than 400 nanometers (nm). Together with specific detectors and examination protocols, a superior spatial resolution up to 400 nm (10 % MTF) can be achieved, thereby exceeding the resolution capacity of typical micro-CT systems. The technical concept of nano-CT imaging as well as the basics of specimen preparation are demonstrated exemplarily. Characteristics of atherosclerotic plaques (intraplaque hemorrhage and calcifications) in a murine model of atherosclerosis (ApoE (-/-)/LDLR(-/-) double knockout mouse) are demonstrated in the context of superior spatial resolution in comparison to micro-CT. Furthermore, this article presents the application of nano-CT for imaging cerebral microcirculation (murine), lung structures (porcine), and trabecular microstructure (ovine) in contrast to micro-CT imaging. This review shows the potential of nano-CT as a radiological method in biomedical basic research and discusses the application of experimental, high resolution CT techniques in consideration of other high resolution cross-sectional imaging techniques. Nano-computed tomography is a high resolution CT-technology for 3D imaging at sub-micrometer resolution. The technical concept bases on a further development of the established ex-vivo-micro-CT technology. By improvement of the spatial resolution, structures at a cellular level become visible (e.g. osteocyte lacunae). © Georg Thieme Verlag KG Stuttgart · New York.

Pathogen group specific risk factors for clinical mastitis, intramammary infection and blind quarters at the herd, cow and quarter level in smallholder dairy farms in Jimma, Ethiopia.

PubMed

Tolosa, T; Verbeke, J; Ayana, Z; Piepers, S; Supré, K; De Vliegher, S

2015-07-01

A cross-sectional study on clinical mastitis, intramammary infection (IMI) and blind quarters was conducted on 50 smallholder dairy farms in Jimma, Ethiopia. A questionnaire was performed, and quarters of 211 cows were sampled and bacteriologically cultured. Risk factors at the herd, cow, and quarter level for clinical mastitis and (pathogen-specific) intramammary infection were studied using multilevel modeling. As well, factors associated with quarters being blind were studied. Eleven percent of the cows and 4% of the quarters had clinical mastitis whereas 85% of the cows and 51% of the quarters were infected. Eighteen percent of the cows had one or more blind quarter(s), whereas 6% of the quarters was blind. Non-aureus staphylococci were the most frequently isolated pathogens in both clinical mastitis cases and IMI. The odds of clinical mastitis was lower in herds where heifers were purchased in the last year [odds ratio (OR) with 95% confidence interval: 0.11 (0.01-0.90)], old cows (>4 years) [OR: 0.45 (0.18-1.14)], and quarters not showing teat injury [OR: 0.23 (0.07-0.77)]. The odds of IMI caused by any pathogen was higher in herds not practicing teat drying before milking (opposed to drying teats with 1 towel per cow) [OR: 1.68 (1.05-2.69)], cows in later lactation (>180 DIM opposed to ≤90 DIM) [OR: 1.81 (1.14-2.88)], cows with a high (>3) body condition score (BCS) [OR: 1.57 (1.06-2.31)], right quarters (opposed to a left quarter position) [OR: 1.47 (1.10-1.98)], and quarters showing teat injury [OR: 2.30 (0.97-5.43)]. Quarters of cows in herds practicing bucket-fed calf feeding (opposed to suckling) had higher odds of IMI caused by Staphylococcus aureus [OR: 6.05 (1.31-27.90)]. Except for BCS, IMI caused by non-aureus staphylococci was associated with the same risk factors as IMI caused by any pathogen. No access to feed and water immediately after milking [OR: 2.41 (1.26-4.60)], higher parity [OR: 3.60 (1.20-10.82)] and tick infestation [OR: 2.42 (1.02-5.71)] were risk factors for quarters being blind. In conclusion, replacement of old cows, prevention of teat injuries/lesions, drying teats with 1 towel per cow before milking, improving fertility in order to shorten the lactation period, allowing (restricted) suckling, access to feed and water immediately after milking, and improving tick control could improve udder health in Jimma. Copyright © 2015 Elsevier B.V. All rights reserved.

Distribution of non-aureus staphylococci species in udder quarters with low and high somatic cell count, and clinical mastitis.

PubMed

Condas, Larissa A Z; De Buck, Jeroen; Nobrega, Diego B; Carson, Domonique A; Roy, Jean-Philippe; Keefe, Greg P; DeVries, Trevor J; Middleton, John R; Dufour, Simon; Barkema, Herman W

2017-07-01

The effect of non-aureus staphylococci (NAS) in bovine mammary health is controversial. Overall, NAS intramammary infections (IMI) increase somatic cell count (SCC), with an effect categorized as mild, mostly causing subclinical or mild to moderate clinical mastitis. However, based on recent studies, specific NAS may affect the udder more severely. Some of these apparent discrepancies could be attributed to the large number of species that compose the NAS group. The objectives of this study were to determine (1) the SCC of quarters infected by individual NAS species compared with NAS as a group, culture-negative, and major pathogen-infected quarters; (2) the distribution of NAS species isolated from quarters with low SCC (<200,000 cells/mL) and high SCC (≥200,000 cells/mL), and clinical mastitis; and (3) the prevalence of NAS species across quarters with low and high SCC. A total of 5,507 NAS isolates, 3,561 from low SCC quarters, 1,873 from high SCC quarters, and 73 from clinical mastitis cases, were obtained from the National Cohort of Dairy Farms of the Canadian Bovine Mastitis Research Network. Of quarters with low SCC, high SCC, or clinical mastitis, 7.6, 18.5, and 4.3% were NAS positive, respectively. The effect of NAS IMI on SCC was estimated using mixed-effect linear regression; prevalence of NAS IMI was estimated using Bayesian analyses. Mean SCC of NAS-positive quarters was 70,000 cells/mL, which was higher than culture-negative quarters (32,000 cells/mL) and lower than major pathogen-positive quarters (129,000 to 183,000 cells/mL). Compared with other NAS species, SCC was highest in quarters positive for Staphylococcus capitis, Staphylococcus gallinarum, Staphylococcus hyicus, Staphylococcus agnetis, or Staphylococcus simulans. In NAS-positive quarters, Staphylococcus xylosus (12.6%), Staphylococcus cohnii (3.1%), and Staphylococcus equorum (0.6%) were more frequently isolated from quarters with low SCC than other NAS species, whereas Staphylococcus sciuri (14%) was most frequently isolated from clinical mastitis cases. Finally, in NAS-positive quarters, Staphylococcus chromogenes, S. simulans, Staphylococcus epidermidis, and Staphylococcus haemolyticus were isolated with similar frequency from among low SCC and high SCC quarters and clinical mastitis cases. Staphylococcus chromogenes, S. simulans, S. xylosus, S. haemolyticus, S. epidermidis, S. agnetis, Staphylococcus arlettae, S. capitis, S. gallinarum, S. sciuri, and Staphylococcus warneri were more prevalent in high than in low SCC quarters. Because the NAS are a large, heterogeneous group, considering them as a single group rather than at the species, or even subspecies level, has undoubtedly contributed to apparent discrepancies among studies as to their distribution and importance in IMI and mastitis. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

10 CFR 34.69 - Records of quarterly inventory.

Code of Federal Regulations, 2010 CFR

2010-01-01

... INDUSTRIAL RADIOGRAPHIC OPERATIONS Recordkeeping Requirements § 34.69 Records of quarterly inventory. (a) Each licensee shall maintain records of the quarterly inventory of sealed sources and of devices... 10 Energy 1 2010-01-01 2010-01-01 false Records of quarterly inventory. 34.69 Section 34.69 Energy...

77 FR 27021 - Proposed Information Collection; Comment Request; Quarterly Survey of Financial Services...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-08

... Request; Quarterly Survey of Financial Services Transactions Between U.S. Financial Services Providers [email protected] . SUPPLEMENTARY INFORMATION: I. Abstract Form BE-185, Quarterly Survey of Financial Services Transactions between U.S. Financial Services Providers and Foreign Persons, obtains quarterly data from U.S...

Commercial space and launch insurance : current market and future outlook : fourth quarter 2002 Quarterly Launch Report

DOT National Transportation Integrated Search

2002-01-01

Since the last review of the space and launch insurance industry (see "Update of the Space and Launch Insurance Industry," 4th quarter, : 1998 Quarterly Launch Report), many changes have occurred in the market. This report endeavors to examine the cu...

39 CFR 3050.25 - Volume and revenue data.

Code of Federal Regulations, 2010 CFR

2010-07-01

... billing determinants, broken out by quarter, within 90 days of the close of each fiscal year; (c) Revenue, pieces, and weight by rate category and special service by quarter, within 30 days of the close of the quarter; (d) Quarterly Statistics Report, including estimates by shape, weight, and indicia, within 30...

Nuclear medicine training and practice in Poland.

PubMed

Teresińska, Anna; Birkenfeld, Bożena; Królicki, Leszek; Dziuk, Mirosław

2014-10-01

In Poland, nuclear medicine (NM) has been an independent specialty since 1988. At the end of 2013, the syllabus for postgraduate specialization in NM has been modified to be in close accordance with the syllabus approved by the European Union of Medical Specialists and is expected to be enforced before the end of 2014. The National Consultant in Nuclear Medicine is responsible for the specialization program in NM. The Medical Center of Postgraduate Training is the administrative body which accepts the specialization programs, supervises the training, organizes the examinations, and awards the specialist title. Specialization in NM for physicians lasts for five years. It consists of 36 months of training in a native nuclear medicine department, 12 months of internship in radiology, 3 months in cardiology, 3 months in endocrinology, 3 months in oncology, and 3 months in two other departments of NM. If a NM trainee is a specialist of a clinical discipline and/or is after a long residency in NM departments, the specialization in NM can be shortened to three years. During the training, there are obligatory courses to be attended which include the elements of anatomy imaging in USG, CT, and MR. Currently, there are about 170 active NM specialists working for 38.5 million inhabitants in Poland. For other professionals working in NM departments, it is possible to get the title of a medical physics specialist after completing 3.5 years of training (for those with a master's in physics, technical physics or biomedical engineering) or the title of a radiopharmacy specialist after completing 3 years of training (for those with a master's in chemistry or biology). At present, the specialization program in NM for nurses is being developed by the Medical Centre of Postgraduate Education. Continuing education and professional development are obligatory for all physicians and governed by the Polish Medical Chamber. The Polish Society of Nuclear Medicine (PTMN) organizes regular postgraduate training for physicians working in NM. Educational programs are comprehensive, covering both diagnostics and current forms of radioisotope therapy. They are aimed not only at physicians specialized/specializing in NM, but also at other medical professionals employed in radionuclide departments as well as physicians of other specialties.

Mobilization and Defense Management Technical Reports Series. The Impact of OSHA (Occupational Safety and Health Administration) and EPA (Environmental Protection Agency) on Defense Industry and the Implications for Mobilization.

DTIC Science & Technology

1983-05-01

mat of the voluntary standards thean in existence (JASI and NVA standards, for wcmmle). fwue affected the broad spectrum of Nm rican industry. As OBIA ...have been funded. As OMA matured, programs, standards, and inspections were significantly improved and gained industry aeptance. OBIA has deleted many

Navigation Operational Concept,

DTIC Science & Technology

1991-08-01

Area Control Facility AFSS Automated Flight Service Station AGL Above Ground Level ALSF-2 Approach Light System with Sequence Flasher Model 2 ATC Air...equipment contributes less than 0.30 NM error at the missed approach point. This total system use accuracy allows for flight technical error of up to...means for transition from instrument to visual flight . This function is provided by a series of standard lighting systems : the Approach Lighting

Correlating Near-Source Rock Damage from Single-Hole Explosions to Seismic Waves (Postprint)

DTIC Science & Technology

2012-05-07

Technical Paper APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED. AIR FORCE RESEARCH LABORATORY Space Vehicles Directorate...Space Vehicles Directorate 3550 Aberdeen Ave SE 3550 Aberdeen Ave SE 11. SPONSOR/MONITOR’S REPORT Kirtland AFB, NM 87117-5776...function of pressure, • Fluid permeability as a function of pressure, • Electrical resistivity as a function of pressure, and • Rock strength. The

JPRS Report, Science & Technology, USSR: Computers.

DTIC Science & Technology

1988-07-08

Computers DISTRIBUTION STAfpiEFTX Approved !CJ- public vekrase; Distribution Unla;u;ed DTIC QUALITY INSPECTED S REPRODUCED BY U.S. DEPARTMENT OF...COMMERCE National Technical Information Service SPRINGFIELD, VA. 22161 /O o f\\H JPRS-UCC-88-002 8 JULY 1988 SCIENCE & TECHNOLOGY USSR: COMPUTERS ...CONTENTS GENERAL Computers : Steps to the World Level ,nm^VA „ 17Q (V. Kovalenko; SOTSIAL1STICIIESKAYA INDUSTRIYA, No 178, 4 Aug 87

Solar Observations on Magneto-Convection

DTIC Science & Technology

1989-05-31

Technical Library National Solar Observatory Sunspot, NM 88349 Karl - Schwarzschild -Strasse 1 8046 Garching bei Mundhen Solar Observations On Magneto...Schmidt, Hermann-Ulrich Schmidt, Hans-Christoph Thomas (eds.) Max-Planck-Institut fir Physik und Astrophysik Institut fiur Astrophysik Karl ... Schwarzschild -St-. 1 D-8046 Garching, FklG 14TIS CRiA.&l DTIC TA. U~Jar,iou8:ed B ......... ... Distribution I -- Availability COcý----- Avail and or Dist special

The influence of size on the toxicity of an encapsulated pesticide: a comparison of micron- and nano-sized capsules.

PubMed

Meredith, Alicea N; Harper, Bryan; Harper, Stacey L

2016-01-01

Encapsulation technology involves entrapping a chemical active ingredient (a.i.) inside a hollow polymeric shell and has been applied to commercial pesticide manufacturing for years to produce capsule suspension (CS) formulations with average particle sizes in the micron-scale. The few literature sources that investigate the environmental fate and toxicity to non-target organisms of encapsulated commercially available pesticide products with regard to capsule size report on average sizes between 20 and 50 μm. Here, we have identified a CS formulation with an average capsule size of approximately 2 μm with some capsules extending into the nanometer scale (~200 nm). Determining how carrier size influences toxicity is important to understanding if current pesticide risk assessments are sufficient to protect against products that incorporate encapsulation technology. Here, a commercial pyrethroid CS pesticide with lambda-cyhalothrin (λ-Cy) as the a.i. was separated into two suspensions, a fraction consisting of nano-sized capsules (~250 nm) and a fraction of micron-sized capsules (~2200 nm) in order to investigate the influence of capsule size on toxicity to embryonic zebrafish, Danio rerio. Toxicity was evaluated 24h after exposure to equivalent amounts of a.i. by the presence and severity of pyrethroid-specific tremors, 14 sublethal developmental impacts and mortality. Fish exposed to greater than 20 μg a.i. L(-1) technical λ-Cy or formulated product experienced curvature of the body axis, pericardial edema, craniofacial malformations, and mortality. Exposure to the unfractionated formulation, micro fraction, nano fraction and technical a.i. resulted in no significant differences in the occurrence of sublethal impacts or mortality; however, the technical a.i. exposure resulted in significantly less fish experiencing tremors and shorter tremors compared to any of the formulated product exposures. This suggests that the capsule size does not influence the toxic response of the entrapped λ-Cy, but the presence or absence of the capsules does. Testing across other encapsulated products is needed to determine if size does not have influence on toxicity regardless of encapsulation technology. Copyright © 2015 Elsevier Ltd. All rights reserved.

Considerations for fine hole patterning for the 7nm node

NASA Astrophysics Data System (ADS)

Yaegashi, Hidetami; Oyama, Kenichi; Hara, Arisa; Natori, Sakurako; Yamauchi, Shohei; Yamato, Masatoshi; Koike, Kyohei

2016-03-01

One of the practical candidates to produce 7nm node logic devices is to use the multiple patterning with 193-immersion exposure. For the multiple patterning, it is important to evaluate the relation between the number of mask layer and the minimum pitch systematically to judge the device manufacturability. Although the number of the time of patterning, namely LE(Litho-Etch) ^ x-time, and overlay steps have to be reduced, there are some challenges in miniaturization of hole size below 20nm. Various process fluctuations on contact hole have a direct impact on device performance. According to the technical trend, 12nm diameter hole on 30nm-pitch hole will be needed on 7nm node. Extreme ultraviolet lithography (EUV) and Directed self-assembly (DSA) are attracting considerable attention to obtain small feature size pattern, however, 193-immersion still has the potential to extend optical lithography cost-effectively for sub-7nm node. The objective of this work is to study the process variation challenges and resolution in post-processing for the CD-bias control to meet sub-20nm diameter contact hole. Another pattern modulation is also demonstrated during post-processing step for hole shrink. With the realization that pattern fidelity and pattern placement management will limit scaling long before devices and interconnects fail to perform intrinsically, the talk will also outline how circle edge roughness (CER) and Local-CD uniformity can correct efficiency. On the other hand, 1D Gridded-Design-Rules layout (1D layout) has simple rectangular shapes. Also, we have demonstrated CD-bias modification on short trench pattern to cut grating line for its fabrication.