Chemical strain-dependent two-dimensional transport at R AlO 3 / SrTiO 3 interfaces ( R = La , Nd , Sm , and Gd )

DOE PAGES

Li, Chen; Shen, Xuan; Yang, Yurong; ...

2016-12-27

Perovskite RAlO 3 (R = La, Nd, Sm, and Gd) films have been deposited epitaxially on (001) TiO 2-terminated SrTiO 3 substrates. In this paper, it is observed that the two-dimensional transport characteristics at the RAlO 3/SrTiO 3 interfaces are very sensitive to the species of rare-earth element, that is to chemical strain. Although electron energy loss spectroscopy measurements show that electron transfer occurs in all the four polar/nonpolar heterostructures, the amount of electrons transferred across SmAlO 3/SrTiO 3 and GdAlO 3/SrTiO 3 interfaces are much less than those across LaAlO 3/SrTiO 3 and NdAlO 3/SrTiO 3 interfaces. First-principles calculationsmore » reveal the competition between ionic polarization and electronic polarization in the polar layers in compensating the build-in polarization due to the polar discontinuity at the interface. Finally, in particular, a large ionic polarization is found in SmAlO 3/SrTiO 3 and GdAlO 3/SrTiO 3 systems (which experience the largest tensile epitaxial strain), hence reducing the amount of electrons transferred.« less

Ion-enhanced chemical etching of ZrO2 in a chlorine discharge

NASA Astrophysics Data System (ADS)

Sha, Lin; Cho, Byeong-Ok; Chang, Jane P.

2002-09-01

Chlorine plasma is found to chemically etch ZrO2 thin films in an electron cyclotron resonance reactor, and the etch rate scaled linearly with the square root of ion energy at high ion energies with a threshold energy between 12-20 eV. The etching rate decreased monotonically with increasing chamber pressures, which corresponds to reduced electron temperatures. Optical emission spectroscopy and quadrupole mass spectrometry were used to identify the reaction etching products. No Zr, O, or ZrCl were detected as etching products, but highly chlorinated zirconium compounds (ZrCl2, ZrCl3, and ZrCl4) and ClO were found to be the dominant etching products. ZrCl3 was the dominant etching products at low ion energies, while ZrCl4 became dominant at higher ion energies. This is consistent with greater momentum transfer and enhanced surface chlorination, as determined by x-ray photoelectron spectroscopy, at increased ion energies. Several ion-enhanced chemical reactions are proposed to contribute to the ZrO2 etching. copyright 2002 American Vacuum Society.

Estimating Damage Cost of Net Primary Production due to Climate Change and Ozone(O3) Effect

NASA Astrophysics Data System (ADS)

Park, J. H.; Lee, D. K.; Park, C.; Sung, S.; Kim, H. G.; Mo, Y.; Kim, S.; Kil, S.

2016-12-01

Forests are absorbing and storing carbon dioxide (CO2) through photosynthesis. The forests are not only preventing global warming but also influencing temperature, precipitation and humidity (Costanza et al., 1997; de Groot et al., 2002). Also the forests are recognized as a carbon sink internationally (van Kooten, 2009). The Korean Government supports the economic activity such as carbon offset projects in accordance with 'ACT ON THE MANAGEMENT AND IMPROVEMENT OF CARBON SINK' Article27 (Korea Forest Service, 2013) and aims to make a policy which improves the CO2 capacity of forest for Paris Agreement discussed in UNFCCC COP21, December 2015 (Korea Forest Service, 2015). However, the social-economic activities make to increase aerosols as well as greenhouse gases significantly since the industrial revolution, as a result, the chemical composition of the atmosphere has changed significantly. According to the resent studies, not only CO2 but atmospheric chemistries such as ozone (O3), aerosol and black carbon can be an important factor causing climate change (Hansen et al., 2007; IPCC, 2007). In the past, acid rain affected on forest, but in these days, O3, nitrogen oxide (NOX) and sulfur oxide (SOX) are the most threatening factors on forest ecosystem (Lee et al, 2011). In particular, O3accounts for most of the photochemical products and causes a direct significant impact or damage on the plant because of high toxicity (Han et al., 2006). The research questions of this study are "How does O3 effects on forest productivity in the present and future? " What is the damage cost by the O3 effect in the future? In this study, we developed a statistical model using the parameters which effect on the forest productivity. We estimated the forest productivity using on the derived model in the present and future on a SSP scenarios. Lastly, we evaluated the economic effect or damage cost of O3effect by introducing the concept of climate insurance. The average forest

Heterogeneous Nitration of Tyrosine by NO­3 and N2O5: Rates, Mechanisms and Product Yields

NASA Astrophysics Data System (ADS)

Talukdar, R. K.; Witkowski, B.; Burkholder, J. B.; Roberts, J. M.

2015-12-01

Nitration of protein-bound tyrosine has been identified as a casual connection between air pollution and human health. Tyrosine is a common amino acid, 4-hydroxyphenylalanine, HO-C6H4-CH2-CH(NH2)-C(O)OH), and is present in many atmospheric bio-aerosols. Nitration of the aromatic units of protein molecules in polluted air enhances their allergenicity. The mechanism of heterogeneous nitration process of bio-aerosols by common nitrating agents in the atmosphere, O3/NO2, NO3, N2O5 is not well understood. This chemistry is thought to proceed via reactions with O3 and NO2 on particle surfaces, through mechanisms that are still uncertain. The possible role of higher nitrogen oxides also remains uncertain, partly due to a lack of measurements of fundamental chemical and physical parameters. In this work, we undertook measurements of reactive uptake of NO3, N2O5, as a function of relative humidity and temperature in a tyrosine coated flow tube reactor with chemical ionization mass spectrometric (CIMS) detection. Uptake coefficients on tyrosine coated flow tube were small under low relative humidity but were enhanced by an order of magnitude in the presence of high relative humidity, particularly for N2O5. The measured uptake coefficients were mostly due to reaction with water adsorbed on the surface of the flow tube. Only ~10% of the reactive uptake could be attributed to reaction with tyrosine. Following uptake, the contents of the flow tube were extracted, and analyzed using electrospray ionization - mass spectrometer (ESI-MS) to identify and quantify the products of the nitration reaction. The only organic reaction product detected was 3-nitro-tyrosine (3-NT). The measured uptake coefficients, mechanism of the title reactions and the possible atmospheric implications of these findings will be discussed.

Products and yields from O3 photodissociation at 1576 A

NASA Technical Reports Server (NTRS)

Taherian, M. R.; Slanger, T. G.

1985-01-01

An analysis has been made of the primary atomic and molecular products arising from O3 photodissociation at 1576 A. The yield of oxygen atoms is 1.90 + or - 0.30, of which 71 percent are O(3P) and 29 percent are O(1D). Since a primary yield greater than unity can only be a consequence of three-fragment dissociation, these results suggest that fragmentation into three O(3P) atoms, and production of O(1D) plus a singlet oxygen molecule, have comparable yields. Observation of prompt emission in the 7300-8100 A spectral region indicates that the singlet O2 is O2(b 1Sigma + g). Vibrational levels in the range v = 0-6 have been detected, the distribution corresponding to a vibrational temperature of 1000 K.

PRISM 3: expanded prediction of natural product chemical structures from microbial genomes

PubMed Central

Skinnider, Michael A.; Merwin, Nishanth J.; Johnston, Chad W.

2017-01-01

Abstract Microbial natural products represent a rich resource of pharmaceutically and industrially important compounds. Genome sequencing has revealed that the majority of natural products remain undiscovered, and computational methods to connect biosynthetic gene clusters to their corresponding natural products therefore have the potential to revitalize natural product discovery. Previously, we described PRediction Informatics for Secondary Metabolomes (PRISM), a combinatorial approach to chemical structure prediction for genetically encoded nonribosomal peptides and type I and II polyketides. Here, we present a ground-up rewrite of the PRISM structure prediction algorithm to derive prediction of natural products arising from non-modular biosynthetic paradigms. Within this new version, PRISM 3, natural product scaffolds are modeled as chemical graphs, permitting structure prediction for aminocoumarins, antimetabolites, bisindoles and phosphonate natural products, and building upon the addition of ribosomally synthesized and post-translationally modified peptides. Further, with the addition of cluster detection for 11 new cluster types, PRISM 3 expands to detect 22 distinct natural product cluster types. Other major modifications to PRISM include improved sequence input and ORF detection, user-friendliness and output. Distribution of PRISM 3 over a 300-core server grid improves the speed and capacity of the web application. PRISM 3 is available at http://magarveylab.ca/prism/. PMID:28460067

SMA OBSERVATIONS OF THE W3(OH) COMPLEX: PHYSICAL AND CHEMICAL DIFFERENTIATION BETWEEN W3(H{sub 2}O) AND W3(OH)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Qin, Sheng-Li; Schilke, Peter; Sánchez-Monge, Álvaro

2015-04-10

We report on the Submillimeter Array (SMA) observations of molecular lines at 270 GHz toward the W3(OH) and W3(H{sub 2}O) complex. Although previous observations already resolved the W3(H{sub 2}O) into two or three sub-components, the physical and chemical properties of the two sources are not well constrained. Our SMA observations clearly resolved the W3(OH) and W3(H{sub 2}O) continuum cores. Taking advantage of the line fitting tool XCLASS, we identified and modeled a rich molecular spectrum in this complex, including multiple CH{sub 3}CN and CH{sub 3}OH transitions in both cores. HDO, C{sub 2}H{sub 5}CN, O{sup 13}CS, and vibrationally excited lines ofmore » HCN, CH{sub 3}CN, and CH{sub 3}OCHO were only detected in W3(H{sub 2}O). We calculate gas temperatures and column densities for both cores. The results show that W3(H{sub 2}O) has higher gas temperatures and larger column densities than W3(OH) as previously observed, suggesting physical and chemical differences between the two cores. We compare the molecular abundances in W3(H{sub 2}O) to those in the Sgr B2(N) hot core, the Orion KL hot core, and the Orion Compact Ridge, and discuss the chemical origin of specific species. An east–west velocity gradient is seen in W3(H{sub 2}O), and the extension is consistent with the bipolar outflow orientation traced by water masers and radio jets. A north–south velocity gradient across W3(OH) is also observed. However, with current observations we cannot be assured whether the velocity gradients are caused by rotation, outflow, or radial velocity differences of the sub-components of W3(OH)« less

Highly efficient visible-light driven photocatalytic hydrogen production from a novel Z-scheme Er3+:YAlO3/Ta2O5-V5+||Fe3+-TiO2/Au coated composite

NASA Astrophysics Data System (ADS)

Wang, Guowei; Ma, Xue; Wei, Shengnan; Li, Siyi; Qiao, Jing; Wang, Jun; Song, Youtao

2018-01-01

In this work, the preparation of a novel Z-scheme photocatalyst, Er3+:YAlO3/Ta2O5-V5+||Fe3+-TiO2/Au coated composite, for visible-light photocatalytic hydrogen production is reported for the first time. In this photocatalyst, Au nanoparticles as conduction band co-catalyst provide more active sites to enrich electrons. Ta2O5-V5+||Fe3+-TiO2 as composite redox cycle system thoroughly separates the photo-generated electrons and holes. In addition, Er3+:YAlO3 as up-conversion luminescence agent (from visible-light to ultraviolet-light) provides enough ultraviolet-light for satisfying the energy demand of wide band-gap semiconductors (TiO2 and Ta2O5). The photocatalytic hydrogen production can be achieved from methanol as sacrificial agent (electron donor) under visible-light irradiation. The main influence factors such as initial solution pH and molar ratio of TiO2 and Ta2O5 on visible-light photocatalytic hydrogen production activity of Er3+:YAlO3/Ta2O5-V5+||Fe3+-TiO2/Au coated composite are discussed in detail. The results show that the Er3+:YAlO3/Ta2O5-V5+||Fe3+-TiO2/Au coated composite with 1.0:0.5 M ratio of TiO2 and Ta2O5 in methanol aqueous solution at pH = 6.50 displays the highest photocatalytic hydrogen production activity. Furthermore, a high level of photocatalytic activity can be still maintained within three cycles under the same conditions. It implies that the prepared Z-scheme Er3+:YAlO3/Ta2O5-V5+||Fe3+-TiO2/Au coated composite may be a promising photocatalyst utilizing solar energy for hydrogen production.

Chemistry of the system: Al2O3(c)minus HCL aqueous. [chemical reactions resulting from propellant combustion of rocket propellants

NASA Technical Reports Server (NTRS)

Tyree, S. Y., Jr.

1975-01-01

In order to study exhaust gas chemistry for the space shuttle, the vapor pressure of 2 to 1 weight mixtures of 3-M hydrochloric acid and Al2O3 was studied over a l80 minute reaction period at 31 C. The Al2O3 sample was one of high surface area furnished by NASA Langley Research Center. A brief review is given for aqueous aluminum chemistry, and the chemical reactions of combustion products (exhaust gases) of aluminum propellant binders for the space shuttle are listed.

Carbon agent chemical vapor transport growth of Ga2O3 crystal

NASA Astrophysics Data System (ADS)

Jie, Su; Tong, Liu; Jingming, Liu; Jun, Yang; Guiying, Shen; Yongbiao, Bai; Zhiyuan, Dong; Youwen, Zhao

2016-10-01

Beta-type gallium oxide (β-Ga2O3) is a new attractive material for optoelectronic devices. Different methods had been tried to grow high quality β-Ga2O3 crystals. In this work, crystal growth of Ga2O3 has been carried out by chemical vapor transport (CVT) method in a closed quartz tube using C as transport agent and sapphire wafer as seed. The CVT mass flux has been analyzed by theoretical calculations based on equilibrium thermodynamics and 1D diffusional mass transport. The crystal growth experimental results are in agreement with the theoretical predictions. Influence factors of Ga2O3 crystal growth, such as temperature distribution, amount of C as transport agent used, have also been discussed. Structural (XRD) and optical (Raman spectroscopy, photoluminescence spectrum) properties of the CVT-Ga2O3 crystal are presented. Project supported by the National Natural Science Foundation of China (Nos. 61474104, 61504131).

PRISM 3: expanded prediction of natural product chemical structures from microbial genomes.

PubMed

Skinnider, Michael A; Merwin, Nishanth J; Johnston, Chad W; Magarvey, Nathan A

2017-07-03

Microbial natural products represent a rich resource of pharmaceutically and industrially important compounds. Genome sequencing has revealed that the majority of natural products remain undiscovered, and computational methods to connect biosynthetic gene clusters to their corresponding natural products therefore have the potential to revitalize natural product discovery. Previously, we described PRediction Informatics for Secondary Metabolomes (PRISM), a combinatorial approach to chemical structure prediction for genetically encoded nonribosomal peptides and type I and II polyketides. Here, we present a ground-up rewrite of the PRISM structure prediction algorithm to derive prediction of natural products arising from non-modular biosynthetic paradigms. Within this new version, PRISM 3, natural product scaffolds are modeled as chemical graphs, permitting structure prediction for aminocoumarins, antimetabolites, bisindoles and phosphonate natural products, and building upon the addition of ribosomally synthesized and post-translationally modified peptides. Further, with the addition of cluster detection for 11 new cluster types, PRISM 3 expands to detect 22 distinct natural product cluster types. Other major modifications to PRISM include improved sequence input and ORF detection, user-friendliness and output. Distribution of PRISM 3 over a 300-core server grid improves the speed and capacity of the web application. PRISM 3 is available at http://magarveylab.ca/prism/. © The Author(s) 2017. Published by Oxford University Press on behalf of Nucleic Acids Research.

Crystal structure, chemical expansion and phase stability of HoMnO{sub 3} at high temperature

DOE Office of Scientific and Technical Information (OSTI.GOV)

Selbach, Sverre M., E-mail: selbach@material.ntnu.no; Nordli Lovik, Amund; Bergum, Kristin

Anisotropic thermal and chemical expansion of hexagonal HoMnO{sub 3} was investigated by high temperature X-ray diffraction in inert (N{sub 2}) and oxidizing (air) atmospheres up to 1623 K. A second order structural phase transition directly from P6{sub 3}cm to P6{sub 3}/mmc was found at 1298{+-}4 K in N{sub 2} atmosphere, and 1318{+-}4 K in air. For the low temperature polymorph P6{sub 3}cm the contraction of the c-axis was more rapid in inert than in oxidizing atmosphere. The c-axis of the P6{sub 3}/mmc polymorph of HoMnO{sub 3} displayed anomalously high expansion above 1400 K, which is discussed in relation to chemicalmore » expansion caused by point defects. The a-axis expanded stronger in inert than oxidizing atmosphere. Anisotropic chemical and thermal expansion of the P6{sub 3}cm phase of YMnO{sub 3} in N{sub 2}, air and O{sub 2} atmospheres was found to be qualitatively similar to that of HoMnO{sub 3}. Decomposition of hexagonal HoMnO{sub 3} by two different processes occurs in oxidizing atmosphere above {approx}1200 K followed by nucleation and growth of the perovskite polymorph of HoMnO{sub 3}. A rapid, reconstructive transition from the perovskite back to the hexagonal polymorph was observed in situ at 1623 K upon reduction of the partial pressure of oxygen. A phase stability diagram of the hexagonal and orthorhombic polymorphs is proposed. Finally, distinctly non-linear electrical conductivity was observed for both HoMnO{sub 3} and YMnO{sub 3} in oxidizing atmosphere between 555 and 630 K, and shown to be associated with excess oxygen. - Graphical abstract: Chemical expansion of hexagonal HoMnO{sub 3} is observed during HTXRD in different pO{sub 2}. Oxidizing atmosphere favors the competing perovskite polymorph. Electrical conductivity anomalies related to excess oxygen are found at 550-630 K. Highlights: Black-Right-Pointing-Pointer Thermal evolution of crystal structure of HoMnO{sub 3} studied up to 1623 K in air and N{sub 2}. Black

O3, CO2 and chemical fractionation in ponderosa pine saplings

EPA Science Inventory

Environmental factors can affect plant tissue quality which is important for quality of organic matter inputs into soil food webs and decomposition of soil organic matter. Thus the effects of increases in CO2 and O3 and their interactions were determined for various chemical fra...

40 CFR 721.10450 - Oxirane, 2-[[3-(trimethoxysilyl)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)).

Code of Federal Regulations, 2014 CFR

2014-07-01

... Oxirane, 2-[[3-(trimethoxysilyl)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)). (a...)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)). 721.10450 Section 721.10450 Protection... oxirane, 2-[[3-(trimethoxysilyl)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)) (PMN P-02...

40 CFR 721.10450 - Oxirane, 2-[[3-(trimethoxysilyl)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)).

Code of Federal Regulations, 2013 CFR

2013-07-01

... Oxirane, 2-[[3-(trimethoxysilyl)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)). (a...)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)). 721.10450 Section 721.10450 Protection... oxirane, 2-[[3-(trimethoxysilyl)propoxy]methyl]-, reaction products with wollastonite (Ca(SiO3)) (PMN P-02...

Composition-Property Correlation in B2O3-SiO2 Preform Rods Produced Using Modified Chemical Vapor Deposition Technique

NASA Astrophysics Data System (ADS)

Islam, Mohammad; Saleem, Muhammad Rizwan

2012-02-01

Due to unique optical properties of high birefringent (Hi-Bi) fibers for sensing and coherent optical communications, there is a strong interest in process optimization at preform fabrication and fiber drawing stages. Boron-doped silica cladding acts as stress-applying part resulting in polarization properties of Hi-Bi fibers that are strongly dependent on chemical composition. Using modified chemical vapor deposition (MCVD) technique, B2O3-doped silica preform rods were synthesized under different precursor gas flow conditions. Qualitative information about B2O3-SiO2 system composition was derived from etching behavior in nonbuffered HF solution and subsequent microstructural examination using scanning electron microscope. Significant degree of B2O3 incorporation was seen in case of high BCl3:SiCl4 ratio and mild oxygen-deficient processing conditions. Increasing the B2O3 content to ~26 mol% led to a corresponding increase in coefficient of thermal expansion (CTE) to a maximum value of 2.35 ppm/K. The value of refractive index (RI), on the other hand, was found to decrease with increased B2O3 incorporation. A qualitative correlation between B2O3 and SiO2 system composition and physical properties such as CTE and RI was established.

Preparation of γ-Al2O3 films by laser chemical vapor deposition

NASA Astrophysics Data System (ADS)

Gao, Ming; Ito, Akihiko; Goto, Takashi

2015-06-01

γ- and α-Al2O3 films were prepared by chemical vapor deposition using CO2, Nd:YAG, and InGaAs lasers to investigate the effects of varying the laser wavelength and deposition conditions on the phase composition and microstructure. The CO2 laser was found to mostly produce α-Al2O3 films, whereas the Nd:YAG and InGaAs lasers produced γ-Al2O3 films when used at a high total pressure. γ-Al2O3 films had a cauliflower-like structure, while the α-Al2O3 films had a dense and columnar structure. Of the three lasers, it was the Nd:YAG laser that interacted most with intermediate gas species. This promoted γ-Al2O3 nucleation in the gas phase at high total pressure, which explains the cauliflower-like structure of nanoparticles observed.

Reactivity of OH and CH3OH Between 22 and 64 K: Modelling the Gas Phase Production of CH3O in Barnard 1B

PubMed Central

Antiñolo, M.; Agúndez, M.; Jiménez, E.; Ballesteros, B.; Canosa, A.; Dib, G. El; Albaladejo, J.; Cernicharo, J.

2016-01-01

In the last years, ultra-low temperature chemical kinetic experiments have demonstrated that some gas-phase reactions are much faster than previously thought. One example is the reaction between OH and CH3OH, which has been recently found to be accelerated at low temperatures yielding CH3O as main product. This finding opened the question of whether the CH3O observed in the dense core Barnard 1b could be formed by the gas-phase reaction of CH3OH and OH. Several chemical models including this reaction and grain-surface processes have been developed to explain the observed abundance of CH3O with little success. Here we report for the first time rate coefficients for the gas-phase reaction of OH and CH3OH down to a temperature of 22 K, very close to those in cold interstellar clouds. Two independent experimental set-ups based on the supersonic gas expansion technique coupled to the pulsed laser photolysis-laser induced fluorescence technique were used to determine rate coefficients in the temperature range 22-64 K. The temperature dependence obtained in this work can be expressed as k(22-64 K) = (3.6 ± 0.1) × 10−12(T/300 K)−(1.0±0.2) cm3 molecule−1 s−1. Implementing this expression in a chemical model of a cold dense cloud results in CH3O/CH3OH abundance ratios similar or slightly lower than the value of ∼ 3 × 10−3 observed in Barnard 1b. This finding confirms that the gas-phase reaction between OH and CH3OH is an important contributor to the formation of interstellar CH3O. The role of grain-surface processes in the formation of CH3O, although it cannot be fully neglected, remains controversial. PMID:27279655

Reactivity of OH and CH3OH Between 22 and 64 K: Modelling the Gas Phase Production of CH3O in Barnard 1B.

PubMed

Antiñolo, M; Agúndez, M; Jiménez, E; Ballesteros, B; Canosa, A; Dib, G El; Albaladejo, J; Cernicharo, J

2016-05-20

In the last years, ultra-low temperature chemical kinetic experiments have demonstrated that some gas-phase reactions are much faster than previously thought. One example is the reaction between OH and CH 3 OH, which has been recently found to be accelerated at low temperatures yielding CH 3 O as main product. This finding opened the question of whether the CH 3 O observed in the dense core Barnard 1b could be formed by the gas-phase reaction of CH 3 OH and OH. Several chemical models including this reaction and grain-surface processes have been developed to explain the observed abundance of CH 3 O with little success. Here we report for the first time rate coefficients for the gas-phase reaction of OH and CH 3 OH down to a temperature of 22 K, very close to those in cold interstellar clouds. Two independent experimental set-ups based on the supersonic gas expansion technique coupled to the pulsed laser photolysis-laser induced fluorescence technique were used to determine rate coefficients in the temperature range 22-64 K. The temperature dependence obtained in this work can be expressed as k (22-64 K) = (3.6 ± 0.1) × 10 -12 ( T/ 300 K) -(1.0±0.2) cm 3 molecule -1 s -1 . Implementing this expression in a chemical model of a cold dense cloud results in CH 3 O/CH 3 OH abundance ratios similar or slightly lower than the value of ∼ 3 × 10 -3 observed in Barnard 1b. This finding confirms that the gas-phase reaction between OH and CH 3 OH is an important contributor to the formation of interstellar CH 3 O. The role of grain-surface processes in the formation of CH 3 O, although it cannot be fully neglected, remains controversial.

Measurements of in situ chemical ozone (oxidant) production rates

NASA Astrophysics Data System (ADS)

Huang, Hao; Faloon, Kate; Najera, Juan; Bloss, William

2013-04-01

Tropospheric ozone is a major air pollutant, harmful to human health, agricultural crops and vegetation, the main precursor to the atmospheric oxidants which initiate the degradation of most reactive gases emitted to the atmosphere, and an important greenhouse gas in its own right. The capacity to understand and predict tropospheric ozone levels is a key goal for atmospheric science - but one which is challenging, as ozone is formed in the atmosphere from the complex oxidation of VOCs in the presence of NOx and sunlight, on a timescale such that in situ chemical processes, deposition and transport all affect ozone levels. Known uncertainties in emissions, chemistry, dynamics and deposition affect the accuracy of predictions of current and future ozone levels, and hinder development of optimal air quality policies to mitigate against ozone exposure. Recently new approaches to directly measure the local chemical ozone production rate, bypassing the many uncertainties in emissions and chemical schemes, have been developed (Cazorla & Brune, AMT 2010). Here, we describe the development of an analogous Ozone Production Rate (OPR) approach: Air is sampled into parallel reactors, within which ozone formation either occurs as in the ambient atmosphere, or is suppressed. Comparisons of ozone levels exiting a pair of such reactors determines the net chemical oxidant production rate, after correction for perturbation of the NOx-O3 photochemical steady state, and when operated under conditions such that wall effects are minimised. We report preliminary measurements of local chemical ozone production made during the UK NERC ClearfLo (Clean Air for London) campaign at an urban background location in London in January and July 2012. The OPR system was used to measure the local chemical oxidant formation rate, which is compared with observed trends in O3 and NOx and the prevailing meteorology, and with the predictions of a detailed zero-dimensional atmospheric chemistry model

Epitaxial growth of SrTiO3/YBa2Cu3O7 - x heterostructures by plasma-enhanced metalorganic chemical vapor deposition

NASA Astrophysics Data System (ADS)

Liang, S.; Chern, C. S.; Shi, Z. Q.; Lu, P.; Safari, A.; Lu, Y.; Kear, B. H.; Hou, S. Y.

1994-06-01

We report heteroepitaxial growth of SrTiO3 on YBa2Cu3O7-x/LaAlO3 substrates by plasma-enhanced metalorganic chemical vapor deposition. X-ray diffraction results indicated that SrTiO3 films were epitaxially grown on a (001) YBa2Cu3O7-x surface with [100] orientation perpendicular to the surface. The film composition, with Sr/Ti molar ratio in the range of 0.9 to 1.1, was determined by Rutherford backscattering spectrometry and energy dispersive spectroscopy. The thickness of the SrTiO3 films is 0.1-0.2 μm. The epitaxial growth was further evidenced by high-resolution transmission electron microscopy and selected area diffraction. Atomically abrupt SrTiO3/YBa2Cu3O7-x interface and epitaxial growth with [100]SrTiO3∥[001]YBa2Cu3O7-x were observed in this study. The superconducting transition temperature of the bottom YBa2Cu3O7-x layer, as measured by ac susceptometer, did not significantly degrade after the growth of overlayer SrTiO3. The capacitance-voltage measurements showed that the dielectric constant of the SrTiO3 films was as high as 315 at a signal frequency of 100 KHz. The leakage current density through the SrTiO3 films is about 1×10-6 A/cm2 at 2-V operation. Data analysis on the current-voltage characteristic indicated that the conduction process is related to bulk-limited Poole-Frenkel emission.

First-principles calculations of 17O nuclear magnetic resonance chemical shielding in Pb(Zr(1/2)Ti(1/2))O3 and Pb(Mg(1/3)Nb(2/3))O3: linear dependence on transition-metal/oxygen bond lengths.

PubMed

Pechkis, Daniel L; Walter, Eric J; Krakauer, Henry

2011-09-21

First-principles density functional theory oxygen chemical shift tensors were calculated for A(B,B')O(3) perovskite alloys Pb(Zr(1/2)Ti(1/2))O(3) (PZT) and Pb(Mg(1/3)Nb(2/3))O(3) (PMN). Quantum chemistry methods for embedded clusters and the gauge including projector augmented waves (GIPAW) method [C. J. Pickard and F. Mauri, Phys. Rev. B 63, 245101 (2001)] for periodic boundary conditions were used. Results from both methods are in good agreement for PZT and prototypical perovskites. PMN results were obtained using only GIPAW. Both isotropic δ(iso) and axial δ(ax) chemical shifts were found to vary approximately linearly as a function of the nearest-distance transition-metal/oxygen bond length, r(s). Using these results, we argue against Ti clustering in PZT, as conjectured from recent (17)O NMR magic-angle-spinning measurements. Our findings indicate that (17)O NMR measurements, coupled with first-principles calculations, can be an important probe of local structure in complex perovskite solid solutions.

First-principles calculations of 17O nuclear magnetic resonance chemical shielding in Pb(Zr1/2Ti1/2)O3 and Pb(Mg1/3Nb2/3)O3: Linear dependence on transition-metal/oxygen bond lengths

NASA Astrophysics Data System (ADS)

Pechkis, Daniel L.; Walter, Eric J.; Krakauer, Henry

2011-09-01

First-principles density functional theory oxygen chemical shift tensors were calculated for A(B,B')O3 perovskite alloys Pb(Zr1/2Ti1/2)O3 (PZT) and Pb(Mg1/3Nb2/3)O3 (PMN). Quantum chemistry methods for embedded clusters and the gauge including projector augmented waves (GIPAW) method [C. J. Pickard and F. Mauri, Phys. Rev. B 63, 245101 (2001)], 10.1103/PhysRevB.63.245101 for periodic boundary conditions were used. Results from both methods are in good agreement for PZT and prototypical perovskites. PMN results were obtained using only GIPAW. Both isotropic δiso and axial δax chemical shifts were found to vary approximately linearly as a function of the nearest-distance transition-metal/oxygen bond length, rs. Using these results, we argue against Ti clustering in PZT, as conjectured from recent 17O NMR magic-angle-spinning measurements. Our findings indicate that 17O NMR measurements, coupled with first-principles calculations, can be an important probe of local structure in complex perovskite solid solutions.

Chemical reaction mechanisms between Y2O3 stabilized ZrO2 and Gd doped CeO2 with PH3 in coal syngas

NASA Astrophysics Data System (ADS)

Chen, Gang; Kishimoto, Haruo; Yamaji, Katsuhiko; Kuramoto, Koji; Gong, Mingyang; Liu, Xingbo; Hackett, Gregory; Gerdes, Kirk; Horita, Teruhisa

2014-12-01

To clarify the chemical stability of the key materials exposed to coal syngas (CSG) containing PH3 contaminant atmosphere, exposure tests of Y2O3 8 mol.% stabilized ZrO2 (YSZ) and Gd doped CeO2 (GDC) are carried out in simulated CSG with different concentrations of PH3. Significant reaction between YSZ and 10 ppm PH3 in CSG atmosphere is confirmed, and no obvious reaction is detected on the surface of YSZ after exposed in CSG with 1 ppm PH3. YPO4, Zr2.25(PO4)3 and monoclinic Y partial stabilized ZrO2 (m-PSZ) are identified on the YSZ pellet surface after exposed in CSG with 10 ppm PH3. GDC reacted with PH3 even at 1 ppm concentration. A (Ce0.9Gd0.1)PO4 layer is formed on the surface of GDC pellet after exposure in CSG with 10 ppm PH3. Possible reaction mechanisms between YSZ and GDC with PH3 in CSG are clarified. Compared with GDC, YSZ exhibits sufficient phosphorus resistance for devices directly exposed to a coal syngas atmosphere containing low concentration of PH3.

Atomic Layer Deposition Al2O3 Coatings Significantly Improve Thermal, Chemical, and Mechanical Stability of Anodic TiO2 Nanotube Layers

PubMed Central

2017-01-01

We report on a very significant enhancement of the thermal, chemical, and mechanical stability of self-organized TiO2 nanotubes layers, provided by thin Al2O3 coatings of different thicknesses prepared by atomic layer deposition (ALD). TiO2 nanotube layers coated with Al2O3 coatings exhibit significantly improved thermal stability as illustrated by the preservation of the nanotubular structure upon annealing treatment at high temperatures (870 °C). In addition, a high anatase content is preserved in the nanotube layers against expectation of the total rutile conversion at such a high temperature. Hardness of the resulting nanotube layers is investigated by nanoindentation measurements and shows strongly improved values compared to uncoated counterparts. Finally, it is demonstrated that Al2O3 coatings guarantee unprecedented chemical stability of TiO2 nanotube layers in harsh environments of concentrated H3PO4 solutions. PMID:28291942

Controlled optical properties via chemical composition tuning in molybdenum-incorporated β-Ga2O3 nanocrystalline films

NASA Astrophysics Data System (ADS)

Battu, Anil K.; Manandhar, S.; Shutthanandan, V.; Ramana, C. V.

2017-09-01

An approach is presented to design refractory-metal incorporated Ga2O3-based materials with controlled structural and optical properties. The molybdenum (Mo)-content in Ga2O3 was varied from 0 to 11 at% in the sputter-deposited Ga-Mo-O films. Molybdenum was found to significantly affect the structure and optical properties. While low Mo-content (≤4 at%) results in the formation of single-phase (β-Ga2O3), higher Mo-content results in amorphization. Chemically-induced band gap variability (Eg ∼ 1 eV) coupled with structure-modification indicates the electronic-structure changes in Ga-Mo-O. The linear relationship between chemical-composition and optical properties suggests that tailoring the optical-quality and performance of Ga-Mo-O films is possible by tuning the Mo-content.

Controlled optical properties via chemical composition tuning in molybdenum-incorporated β-Ga 2 O 3 nanocrystalline films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Battu, Anil K.; Manandhar, S.; Shutthanandan, V.

An approach is presented to design refractory-metal incorporated Ga2O3-based materials with controlled structural and optical properties. The molybdenum (Mo)-content in Ga2O3 was varied from 0 to 11 at% in the sputter-deposited Ga-Mo-O films. Molybdenum was found to significantly affect the structure and optical properties. While low Mo-content (≤4 at%) results in the formation of single-phase (β-Ga2O3), higher Mo-content results in amorphization. Chemically-induced band gap variability (Eg~1 eV) coupled with structure-modification indicates the electronic-structure changes in Ga-Mo-O. The linear relationship between chemical-composition and optical properties suggests that tailoring the optical-quality and performance of Ga-Mo-O films is possible by tuning the Mo-content.

Wet chemical passivation of YBa2Cu3O(7-x)

NASA Technical Reports Server (NTRS)

Vasquez, R. P.; Hunt, B. D.; Foote, M. C.

1990-01-01

Wet chemical techniques are described for treatment of YBa2Cu3O(7-x) surfaces, which result in the formation of native compounds known to have little or no reactivity to water. Suitable native compounds include CuI, BaSO4, CuS, Cu2S, YF3, and the oxalates. Formation of surface layers in which these nonreactive native compounds are major constituents is verified with X-ray photoelectron spectroscopy (XPS) measurements on YBa2Cu3O(7-x) films treated with dilute solutions of HI, H2SO4, Na2S, HF, or H2C2O4. No significant changes are observed in the XPS spectra when the sulfide, sulfate, or oxalate films are dipped in water, while the iodide and fluoride films show evidence of reaction with water. X-ray diffraction measurements show that the superconducting phase is absent in the sulfide film, but is unaffected by the oxalate and sulfate treatments.

Quantum chemical calculations of Cr2O3/SnO2 using density functional theory method

NASA Astrophysics Data System (ADS)

Jawaher, K. Rackesh; Indirajith, R.; Krishnan, S.; Robert, R.; Das, S. Jerome

2018-03-01

Quantum chemical calculations have been employed to study the molecular effects produced by Cr2O3/SnO2 optimised structure. The theoretical parameters of the transparent conducting metal oxides were calculated using DFT / B3LYP / LANL2DZ method. The optimised bond parameters such as bond lengths, bond angles and dihedral angles were calculated using the same theory. The non-linear optical property of the title compound was calculated using first-order hyperpolarisability calculation. The calculated HOMO-LUMO analysis explains the charge transfer interaction between the molecule. In addition, MEP and Mulliken atomic charges were also calculated and analysed.

Structures and chemical bonding of B{sub 3}O{sub 3}{sup −/0} and B{sub 3}O{sub 3}H{sup −/0}: A combined photoelectron spectroscopy and first-principles theory study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Li-Juan; Xu, Hong-Guang; Feng, Gang

We present a combined photoelectron spectroscopy and first-principles theory study on the structural and electronic properties and chemical bonding of B{sub 3}O{sub 3}{sup −/0} and B{sub 3}O{sub 3}H{sup −/0} clusters. The concerted experimental and theoretical data show that the global-minimum structures of B{sub 3}O{sub 3} and B{sub 3}O{sub 3}H neutrals are very different from those of their anionic counterparts. The B{sub 3}O{sub 3}{sup −} anion is characterized to possess a V-shaped OB–B–BO chain with overall C{sub 2v} symmetry (1A), in which the central B atom interacts with two equivalent boronyl (B≡O) terminals via B–B single bonds as well as withmore » one O atom via a B=O double bond. The B{sub 3}O{sub 3}H{sup −} anion has a C{sub s} (2A) structure, containing an asymmetric OB–B–OBO zig-zag chain and a terminal H atom interacting with the central B atom. In contrast, the C{sub 2v} (1a) global minimum of B{sub 3}O{sub 3} neutral contains a rhombic B{sub 2}O{sub 2} ring with one B atom bonded to a BO terminal and that of neutral B{sub 3}O{sub 3}H (2a) is also of C{sub 2v} symmetry, which is readily constructed from C{sub 2v} (1a) by attaching a H atom to the opposite side of the BO group. The H atom in B{sub 3}O{sub 3}H{sup −/0} (2A and 2a) prefers to interact terminally with a B atom, rather than with O. Chemical bonding analyses reveal a three-center four-electron (3c-4e) π hyperbond in the B{sub 3}O{sub 3}H{sup −} (2A) cluster and a four-center four-electron (4c-4e) π bond (that is, the so-called o-bond) in B{sub 3}O{sub 3} (1a) and B{sub 3}O{sub 3}H (2a) neutral clusters.« less

Quantum chemical study of the mechanism of reaction between NH (X 3sigma-) and H2, H2O, and CO2 under combustion conditions.

PubMed

Mackie, John C; Bacskay, George B

2005-12-29

Reactions of ground-state NH (3sigma-) radicals with H2, H2O, and CO2 have been investigated quantum chemically, whereby the stationary points of the appropriate reaction potential energy surfaces, that is, reactants, products, intermediates, and transition states, have been identified at the G3//B3LYP level of theory. Reaction between NH and H2 takes place via a simple abstraction transition state, and the rate coefficient for this reaction as derived from the quantum chemical calculations, k(NH + H2) = (1.1 x 10(14)) exp(-20.9 kcal mol(-1)/RT) cm3 mol(-1) s(-1) between 1000 and 2000 K, is found to be in good agreement with experiment. For reaction between triplet NH and H2O, no stable intermediates were located on the triplet reaction surface although several stable species were found on the singlet surface. No intersystem crossing seam between triplet NH + H2O and singlet HNO + H2 (the products of lowest energy) was found; hence there is no evidence to support the existence of a low-energy pathway to these products. A rate coefficient of k(NH + H2O) = (6.1 x 10(13)) exp(-32.8 kcal mol(-1)/RT) cm3 mol(-1) s(-1) between 1000 and 2000 K for the reaction NH (3sigma-) + H2O --> NH2 (2B) + OH (2pi) was derived from the quantum chemical results. The reverse rate coefficient, calculated via the equilibrium constant, is in agreement with values used in modeling the thermal de-NO(x) process. For the reaction between triplet NH and CO2, several stable intermediates on both triplet and singlet reaction surfaces were located. Although a pathway from triplet NH + CO2 to singlet HNO + CO involving intersystem crossing in an HN-CO2 adduct was discovered, no pathway of sufficiently low activation energy was discovered to compare with that found in an earlier experiment [Rohrig, M.; Wagner, H. G. Proc. Combust. Inst. 1994, 25, 993.].

Controlled optical properties via chemical composition tuning in molybdenum-incorporated β-Ga 2O 3 nanocrystalline films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Battu, Anil K.; Manandhar, S.; Shutthanandan, V.

Here, an approach is presented to design refractory-metal incorporated Ga 2O 3-based materials with controlled structural and optical properties. The molybdenum (Mo)-content in Ga 2O 3 was varied from 0 to 11 at% in the sputter-deposited Ga-Mo-O films. Molybdenum was found to significantly affect the structure and optical properties. While low Mo-content (≤4 at%) results in the formation of single-phase (β-Ga 2O 3), higher Mo-content results in amorphization. Chemically-induced band gap variability (E g ~ 1 eV) coupled with structure-modification indicates the electronic-structure changes in Ga-Mo-O. The linear relationship between chemical-composition and optical properties suggests that tailoring the optical-quality andmore » performance of Ga-Mo-O films is possible by tuning the Mo-content.« less

Controlled optical properties via chemical composition tuning in molybdenum-incorporated β-Ga 2O 3 nanocrystalline films

DOE PAGES

Battu, Anil K.; Manandhar, S.; Shutthanandan, V.; ...

2017-07-01

Here, an approach is presented to design refractory-metal incorporated Ga 2O 3-based materials with controlled structural and optical properties. The molybdenum (Mo)-content in Ga 2O 3 was varied from 0 to 11 at% in the sputter-deposited Ga-Mo-O films. Molybdenum was found to significantly affect the structure and optical properties. While low Mo-content (≤4 at%) results in the formation of single-phase (β-Ga 2O 3), higher Mo-content results in amorphization. Chemically-induced band gap variability (E g ~ 1 eV) coupled with structure-modification indicates the electronic-structure changes in Ga-Mo-O. The linear relationship between chemical-composition and optical properties suggests that tailoring the optical-quality andmore » performance of Ga-Mo-O films is possible by tuning the Mo-content.« less

Heteroepitaxial growth of Ba1 - xSrxTiO3/YBa2Cu3O7 - x by plasma-enhanced metalorganic chemical vapor deposition

NASA Astrophysics Data System (ADS)

Chern, C. S.; Liang, S.; Shi, Z. Q.; Yoon, S.; Safari, A.; Lu, P.; Kear, B. H.; Goodreau, B. H.; Marks, T. J.; Hou, S. Y.

1994-06-01

Epitaxial Ba1-xSrxTiO3(BST)/YBa2Cu3O7-x heterostructures with superior electrical and dielectric properties have been fabricated by plasma-enhanced metalorganic chemical vapor deposition (PE-MOCVD). Data of x-ray diffraction and high resolution transmission electron microscopy showed that <100> oriented Ba1-xSrxTiO3 layers were epitaxially deposited on epitaxial (001) YBa2Cu3O7-x layers. The leakage current density through the Ba1-xSrxTiO3 films was about 10-7 A/cm2 at 2 V (about 2×105 V/cm) operation. Moreover, the results of capacitance-temperature measurements showed that the PE-MOCVD Ba1-xSrxTiO3 films had Curie temperatures of about 30 °C and a peak dielectric constant of 600 at zero bias voltage. The Rutherford backscattering spectrometry and x-ray diffraction results showed that the BST film composition was controlled between Ba0.75Sr0.25TiO3 and Ba0.8Sr0.2TiO3. The structural and electrical properties of the Ba1-xSrxTiO3/YBa2Cu3O7-x heterostructure indicated that conductive oxide materials with close lattice to Ba1-xSrxTiO3 can be good candidates for the bottom electrode.

Synthesis of BiFeO3 thin films by chemical solution deposition - Structural and magnetic studies

NASA Astrophysics Data System (ADS)

Angappane, S.; Kambhala, Nagaiah

2012-06-01

BiFeO3 thin films were deposited on Si (100) substrates by chemical solution deposition. A precursor solution of bismuth acetate and iron acetylacetonate dissolved in distilled water and acetic acid was spin coated on to silicon substrates at ambient conditions, followed by drying and annealing at 650 °C. The films were characterized by XRD and FESEM to study structural properties and morphology. The magnetic properties studied by SQUID magnetometer shows the ferromagnetic nature of the chemical solution deposited BiFeO3 films which are crucial for low cost device applications.

Thermal desorption of dimethyl methylphosphonate from MoO 3

DOE PAGES

Head, Ashley R.; Tang, Xin; Hicks, Zachary; ...

2017-03-03

Organophosphonates are used as chemical warfare agents, pesticides, and corrosion inhibitors. New materials for the sorption, detection, and decomposition of these compounds are urgently needed. To facilitate materials and application innovation, a better understanding of the interactions between organophosphonates and surfaces is required. To this end, we have used diffuse reflectance infrared Fourier transform spectroscopy to investigate the adsorption geometry of dimethyl methylphosphonate (DMMP) on MoO 3, a material used in chemical warfare agent filtration devices. We further applied ambient pressure X-ray photoelectron spectroscopy and temperature programmed desorption to study the adsorption and desorption of DMMP. While DMMP adsorbs intactmore » on MoO 3, desorption depends on coverage and partial pressure. At low coverages under UHV conditions, the intact adsorption is reversible. Decomposition occurs with higher coverages, as evidenced by PCH x and PO x decomposition products on the MoO 3 surface. Heating under mTorr partial pressures of DMMP results in product accumulation.« less

Reactions of CH3SH and CH3SSCH3 with gas-phase hydrated radical anions (H2O)n(•-), CO2(•-)(H2O)n, and O2(•-)(H2O)n.

PubMed

Höckendorf, Robert F; Hao, Qiang; Sun, Zheng; Fox-Beyer, Brigitte S; Cao, Yali; Balaj, O Petru; Bondybey, Vladimir E; Siu, Chi-Kit; Beyer, Martin K

2012-04-19

The chemistry of (H(2)O)(n)(•-), CO(2)(•-)(H(2)O)(n), and O(2)(•-)(H(2)O)(n) with small sulfur-containing molecules was studied in the gas phase by Fourier transform ion cyclotron resonance mass spectrometry. With hydrated electrons and hydrated carbon dioxide radical anions, two reactions with relevance for biological radiation damage were observed, cleavage of the disulfide bond of CH(3)SSCH(3) and activation of the thiol group of CH(3)SH. No reactions were observed with CH(3)SCH(3). The hydrated superoxide radical anion, usually viewed as major source of oxidative stress, did not react with any of the compounds. Nanocalorimetry and quantum chemical calculations give a consistent picture of the reaction mechanism. The results indicate that the conversion of e(-) and CO(2)(•-) to O(2)(•-) deactivates highly reactive species and may actually reduce oxidative stress. For reactions of (H(2)O)(n)(•-) with CH(3)SH as well as CO(2)(•-)(H(2)O)(n) with CH(3)SSCH(3), the reaction products in the gas phase are different from those reported in the literature from pulse radiolysis studies. This observation is rationalized with the reduced cage effect in reactions of gas-phase clusters. © 2012 American Chemical Society

Yellow phosphorus process to convert toxic chemicals to non-toxic products

DOEpatents

Chang, S.G.

1994-07-26

The present invention relates to a process for generating reactive species for destroying toxic chemicals. This process first contacts air or oxygen with aqueous emulsions of molten yellow phosphorus. This contact results in rapid production of abundant reactive species such as O, O[sub 3], PO, PO[sub 2], etc. A gaseous or liquid aqueous solution organic or inorganic chemicals is next contacted by these reactive species to reduce the concentration of toxic chemical and result in a non-toxic product. The final oxidation product of yellow phosphorus is phosphoric acid of a quality which can be recovered for commercial use. A process is developed such that the byproduct, phosphoric acid, is obtained without contamination of toxic species in liquids treated. A gas stream containing ozone without contamination of phosphorus containing species is also obtained in a simple and cost-effective manner. This process is demonstrated to be effective for destroying many types of toxic organic, or inorganic, compounds, including polychlorinated biphenyls (PCB), aromatic chlorides, amines, alcohols, acids, nitro aromatics, aliphatic chlorides, polynuclear aromatic compounds (PAH), dyes, pesticides, sulfides, hydroxyamines, ureas, dithionates and the like. 20 figs.

Yellow phosphorus process to convert toxic chemicals to non-toxic products

DOEpatents

Chang, Shih-Ger

1994-01-01

The present invention relates to a process for generating reactive species for destroying toxic chemicals. This process first contacts air or oxygen with aqueous emulsions of molten yellow phosphorus. This contact results in rapid production of abundant reactive species such as O, O.sub.3, PO, PO.sub.2, etc. A gaseous or liquid aqueous solution organic or inorganic chemicals is next contacted by these reactive species to reduce the concentration of toxic chemical and result in a non-toxic product. The final oxidation product of yellow phosphorus is phosphoric acid of a quality which can be recovered for commercial use. A process is developed such that the byproduct, phosphoric acid, is obtained without contamination of toxic species in liquids treated. A gas stream containing ozone without contamination of phosphorus containing species is also obtained in a simple and cost-effective manner. This process is demonstrated to be effective for destroying many types of toxic organic, or inorganic, compounds, including polychlorinated biphenyls (PCB), aromatic chlorides, amines, alcohols, acids, nitro aromatics, aliphatic chlorides, polynuclear aromatic compounds (PAH), dyes, pesticides, sulfides, hydroxyamines, ureas, dithionates and the like.

Azadirachta indica plant-assisted green synthesis of Mn3O4 nanoparticles: Excellent thermal catalytic performance and chemical sensing behavior.

PubMed

Sharma, Jitendra Kumar; Srivastava, Pratibha; Ameen, Sadia; Akhtar, M Shaheer; Singh, Gurdip; Yadava, Sudha

2016-06-15

The leaf extract of Azadirachta indica (Neem) plant was utilized as reducing agent for the green synthesis of Mn3O4 nanoparticles (NPs). The crystalline analysis demonstrated the typical tetragonal hausmannite crystal structure of Mn3O4, which confirmed the formation of Mn3O4 NPs without the existence of other oxides. Green synthesized Mn3O4 NPs were applied for the catalytic thermal decomposition of ammonium perchlorate (AP) and as working electrode for fabricating the chemical sensor. The excellent catalytic effect for the thermal decomposition of AP was observed by decreasing the decomposition temperature by 175 °C with single decomposing step. The fabricated chemical sensor based on green synthesized Mn3O4 NPs displayed high, reliable and reproducible sensitivity of ∼569.2 μA mM(-1) cm(-2) with reasonable limit of detection (LOD) of ∼22.1 μM and the response time of ∼10 s toward the detection of 2-butanone chemical. A relatively good linearity in the ranging from ∼20 to 160 μM was detected for Mn3O4 NPs electrode based 2-butanone chemical sensor. Copyright © 2016 Elsevier Inc. All rights reserved.

Kinetics of Valeric Acid Ketonization and Ketenization in Catalytic Pyrolysis on Nanosized SiO2 , γ-Al2 O3 , CeO2 /SiO2 , Al2 O3 /SiO2 and TiO2 /SiO2.

PubMed

Kulyk, Kostiantyn; Palianytsia, Borys; Alexander, John D; Azizova, Liana; Borysenko, Mykola; Kartel, Mykola; Larsson, Mats; Kulik, Tetiana

2017-07-19

Valeric acid is an important renewable platform chemical that can be produced efficiently from lignocellulosic biomass. Upgrading of valeric acid by catalytic pyrolysis has the potential to produce value added biofuels and chemicals on an industrial scale. Understanding the different mechanisms involved in the thermal transformations of valeric acid on the surface of nanometer-sized oxides is important for the development of efficient heterogeneously catalyzed pyrolytic conversion techniques. In this work, the thermal decomposition of valeric acid on the surface of nanoscale SiO 2 , γ-Al 2 O 3 , CeO 2 /SiO 2 , Al 2 O 3 /SiO 2 and TiO 2 /SiO 2 has been investigated by temperature-programmed desorption mass spectrometry (TPD MS). Fourier transform infrared spectroscopy (FTIR) has also been used to investigate the structure of valeric acid complexes on the oxide surfaces. Two main products of pyrolytic conversion were observed to be formed depending on the nano-catalyst used-dibutylketone and propylketene. Mechanisms of ketene and ketone formation from chemisorbed fragments of valeric acid are proposed and the kinetic parameters of the corresponding reactions were calculated. It was found that the activation energy of ketenization decreases in the order SiO 2 >γ-Al 2 O 3 >TiO 2 /SiO 2 >Al 2 O 3 /SiO 2 , and the activation energy of ketonization decreases in the order γ-Al 2 O 3 >CeO 2 /SiO 2 . Nano-oxide CeO 2 /SiO 2 was found to selectively catalyze the ketonization reaction. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dielectric and ferroelectric properties of highly (100)-oriented (Na 0.5Bi 0.5) 0.94Ba 0.06TiO 3 thin films grown on LaNiO 3/γ-Al 2O 3/Si substrates by chemical solution deposition

NASA Astrophysics Data System (ADS)

Guo, Yiping; Akai, Daisuke; Sawada, Kazauki; Ishida, Makoto

2008-07-01

A (Na 0.5Bi 0.5) 0.94Ba 0.06TiO 3 chemical solution was prepared by using barium acetate, nitrate of sodium, nitrate of bismuth, and Ti-isopropoxide as raw materials. A white precipitation appeared during the preparation was analyzed to be Ba(NO 3) 2. We found that ethanolamine is a very effective coordinating ligand of Ba 2+. A transparent and stable (Na 0.5Bi 0.5) 0.94Ba 0.06TiO 3 precursor chemical solution has been achieved by using ethanolamine as a ligand of Ba 2+. (Na 0.5Bi 0.5) 0.94Ba 0.06TiO 3 films were grown on LaNiO 3/γ-Al 2O 3/Si substrates. Highly (100)-oriented (Na 0.5Bi 0.5) 0.94Ba 0.06TiO 3 films were obtained in this work due to lattice match growth. The dielectric, ferroelectric and insulative characteristics against applied field were studied. The conduction current shows an Ohmic conduction behavior at lower voltages and space-charge-limited behavior at higher voltages, respectively. These results indicate that, the (Na 0.5Bi 0.5) 0.94Ba 0.06TiO 3 film is a promising lead-free ferroelectric film.

Ab Initio Chemical Kinetics for the CH3 + O((3)P) Reaction and Related Isomerization-Decomposition of CH3O and CH2OH Radicals.

PubMed

Xu, Z F; Raghunath, P; Lin, M C

2015-07-16

The kinetics and mechanism of the CH3 + O reaction and related isomerization-decomposition of CH3O and CH2OH radicals have been studied by ab initio molecular orbital theory based on the CCSD(T)/aug-cc-pVTZ//CCSD/aug-cc-pVTZ, CCSD/aug-cc-pVDZ, and G2M//B3LYP/6-311+G(3df,2p) levels of theory. The predicted potential energy surface of the CH3 + O reaction shows that the CHO + H2 products can be directly generated from CH3O by the TS3 → LM1 → TS7 → LM2 → TS4 path, in which both LM1 and LM2 are very loose and TS7 is roaming-like. The result for the CH2O + H reaction shows that there are three low-energy barrier processes including CH2O + H → CHO + H2 via H-abstraction and CH2O + H → CH2OH and CH2O + H → CH3O by addition reactions. The predicted enthalpies of formation of the CH2OH and CH3O radicals at 0 K are in good agreement with available experimental data. Furthermore, the rate constants for the forward and some key reverse reactions have been predicted at 200-3000 K under various pressures. Based on the new reaction pathway for CH3 + O, the rate constants for the CH2O + H and CHO + H2 reactions were predicted with the microcanonical variational transition-state/Rice-Ramsperger-Kassel-Marcus (VTST/RRKM) theory. The predicted total and individual product branching ratios (i.e., CO versus CH2O) are in good agreement with experimental data. The rate constant for the hydrogen abstraction reaction of CH2O + H has been calculated by the canonical variational transition-state theory with quantum tunneling and small-curvature corrections to be k(CH2O + H → CHO + H2) = 2.28 × 10(-19) T(2.65) exp(-766.5/T) cm(3) molecule(-1) s(-1) for the 200-3000 K temperature range. The rate constants for the addition giving CH3O and CH2OH and the decomposition of the two radicals have been calculated by the microcanonical RRKM theory with the time-dependent master equation solution of the multiple quantum well system in the 200-3000 K temperature range at 1 Torr to

The removal of COD and NH3-N from atrazine production wastewater treatment using UV/O3: experimental investigation and kinetic modeling.

PubMed

Jing, Liang; Chen, Bing; Wen, Diya; Zheng, Jisi; Zhang, Baiyu

2018-01-01

In this study, a UV/O 3 hybrid advanced oxidation system was used to remove chemical oxygen demand (COD), ammonia nitrogen (NH 3 -N), and atrazine (ATZ) from ATZ production wastewater. The removal of COD and NH 3 -N, under different UV and O 3 conditions, was found to follow pseudo-first-order kinetics with rate constants ranging from 0.0001-0.0048 and 0.0015-0.0056 min -1 , respectively. The removal efficiency of ATZ was over 95% after 180 min treatment, regardless the level of UV power. A kinetic model was further proposed to simulate the removal processes and to quantify the individual roles and contributions of photolysis, direct O 3 oxidation, and hydroxyl radical (OH·) induced oxidation. The experimental and kinetic modeling results agreed reasonably well with deviations of 12.2 and 13.1% for the removal of COD and NH 3 -N, respectively. Photolysis contributed appreciably to the degradation of ATZ, while OH· played a dominant role for the removal of both COD and NH 3 -N, especially in alkaline environments. This study provides insights into the treatment of ATZ containing wastewater using UV/O 3 and broadens the knowledge of kinetics of ozone-based advanced oxidation processes.

Quantum Chemical Molecular Dynamics Simulations of 1,3-Dichloropropene Combustion.

PubMed

Ahubelem, Nwakamma; Shah, Kalpit; Moghtaderi, Behdad; Page, Alister J

2015-09-03

Oxidative decomposition of 1,3-dichloropropene was investigated using quantum chemical molecular dynamics (QM/MD) at 1500 and 3000 K. Thermal oxidation of 1,3-dichloropropene was initiated by (1) abstraction of allylic H/Cl by O2 and (2) intra-annular C-Cl bond scission and elimination of allylic Cl. A kinetic analysis shows that (2) is the more dominant initiation pathway, in agreement with QM/MD results. These QM/MD simulations reveal new routes to the formation of major products (H2O, CO, HCl, CO2), which are propagated primarily by the chloroperoxy (ClO2), OH, and 1,3-dichloropropene derived radicals. In particular, intra-annular C-C/C-H bond dissociation reactions of intermediate aldehydes/ketones are shown to play a dominant role in the formation of CO and CO2. Our simulations demonstrate that both combustion temperature and radical concentration can influence the product yield, however not the combustion mechanism.

Hydrogen production from water-glucose solution over NiO/La-NaTaO3 photocatalyst

NASA Astrophysics Data System (ADS)

Mardian, R.; Husin, H.; Pontas, K.; Zaki, M.; Asnawi, T. M.; Ahmadi

2018-03-01

This paper reports the evaluation of La-NaTaO3 photocatalyst performance in producing hydrogen from water-glucose solution. The main goal of the studies is to investigate the influence of glucose as a sacrificial reagent on the photocatalytic efficiency in water splitting reactions under ultraviolet (UV) irradiation. Photocatalyst has been fabricated via sol-gel method and being confirmed using x-ray diffraction (XRD) and scanning electron microscopy (SEM). Nickel loaded La-NaTaO3 photocatalyst are prepared by impregnation method. It was observed that the prepared photocatalysts displayed particle sizes in the 30-250 nm range with orthorhombic structure. Their photocatalytic activity for hydrogen production via water splitting was conducted in a Pyrex glass reactor under UV light irradiation. The aqueous solution contained glucose employed as a renewable organic scavenger. A significant improvement in hydrogen production was observed in glucose-water mixtures and NiO loaded photocatalyst. The prepared La-NaTaO3 showed that the highest activity for hydrogen generation of 35.1 mmol h-1.g-1 was obtained at 0.10 mol.L-1 glucose and 0.3 wt.% NiO. This suggests the important role played by the glucose as electron donor and loading nickel on La-NaTaO3 as a cocatalyst increasing electron storage and suppressing electron-hole recombination.

Recent advances in the metabolic engineering of microorganisms for the production of 3-hydroxypropionic acid as C3 platform chemical.

PubMed

Valdehuesa, Kris Niño G; Liu, Huaiwei; Nisola, Grace M; Chung, Wook-Jin; Lee, Seung Hwan; Park, Si Jae

2013-04-01

Development of sustainable technologies for the production of 3-hydroxypropionic acid (3HP) as a platform chemical has recently been gaining much attention owing to its versatility in applications for the synthesis of other specialty chemicals. Several proposed biological synthesis routes and strategies for producing 3HP from glucose and glycerol are reviewed presently. Ten proposed routes for 3HP production from glucose are described and one of which was recently constructed successfully in Escherichia coli with malonyl-Coenzyme A as a precursor. This resulted in a yield still far from the required level for industrial application. On the other hand, strategies employing engineered E. coli and Klebsiella pneumoniae capable of producing 3HP from glycerol are also evaluated. The titers produced by these recombinant strains reached around 3 %. At its current state, it is evident that a bulk of engineering works is yet to be done to acquire a biosynthesis route for 3HP that is acceptable for industrial-scale production.

Thermal decomposition of ethanol. 4. Ab initio chemical kinetics for reactions of H atoms with CH3CH2O and CH3CHOH radicals.

PubMed

Xu, Z F; Xu, Kun; Lin, M C

2011-04-21

The potential energy surfaces of H-atom reactions with CH(3)CH(2)O and CH(3)CHOH, two major radicals in the decomposition and oxidation of ethanol, have been studied at the CCSD(T)/6-311+G(3df,2p) level of theory with geometric optimization carried out at the BH&HLYP/6-311+G(3df,2p) level. The direct hydrogen abstraction channels and the indirect association/decomposition channels from the chemically activated ethanol molecule have been considered for both reactions. The rate constants for both reactions have been calculated at 100-3000 K and 10(-4) Torr to 10(3) atm Ar pressure by microcanonical VTST/RRKM theory with master equation solution for all accessible product channels. The results show that the major product channel of the CH(3)CH(2)O + H reaction is CH(3) + CH(2)OH under atmospheric pressure conditions. Only at high pressure and low temperature, the rate constant for CH(3)CH(2)OH formation by collisonal deactivation becomes dominant. For CH(3)CHOH + H, there are three major product channels; at high temperatures, CH(3)+CH(2)OH production predominates at low pressures (P < 100 Torr), while the formation of CH(3)CH(2)OH by collisional deactivation becomes competitive at high pressures and low temperatures (T < 500 K). At high temperatures, the direct hydrogen abstraction reaction producing CH(2)CHOH + H(2) becomes dominant. Rate constants for all accessible product channels in both systems have been predicted and tabulated for modeling applications. The predicted value for CH(3)CHOH + H at 295 K and 1 Torr pressure agrees closely with available experimental data. For practical modeling applications, the rate constants for the thermal unimolecular decomposition of ethanol giving key accessible products have been predicted; those for the two major product channels taking place by dehydration and C-C breaking agree closely with available literature data.

Chemical nature of the barrier in Pb/YBa2Cu3O(7-x) tunneling structures

NASA Technical Reports Server (NTRS)

Vasquez, R. P.; Foote, M. C.; Hunt, B. D.; Bajuk, L.

1991-01-01

Several reports of reproducible tunneling measurements on YBa2Cu3O(7-x) thin films or single crystals with a Pb counterelectrode have recently appeared. The nature of the tunnel barrier, formed by air exposure, in these structures has been unknown. In the present work, the chemical nature of the tunnel barrier is studied with X-ray photoelectron spectroscopy (XPS). Laser-ablated films grown on LaAlO3 which have been chemically etched and heated in air are found to form nonsuperconducting surface Ba species, evident in an increase of the high binding energy Ba 3d and O 1s signals. A deposited Pb film about 10 A thick is found to be oxidized, and Cu(+2) is partially reduced to Cu(+1). The tunneling barrier thus appears to consist of species resulting from a combination of the air exposure and a reaction between the superconductor and the deposited Pb counterelectrode.

Direct Dynamics Simulation of the Thermal 3CH2 + 3O2 Reaction. Rate Constant and Product Branching Ratios.

PubMed

Lakshmanan, Sandhiya; Pratihar, Subha; Machado, Francisco B C; Hase, William L

2018-05-31

The reaction of 3 CH 2 with 3 O 2 is of fundamental importance in combustion, and the reaction is complex as a result of multiple extremely exothermic product channels. In the present study, direct dynamics simulations were performed to study the reaction on both the singlet and triplet potential energy surfaces (PESs). The simulations were performed at the UM06/6-311++G(d,p) level of theory. Trajectories were calculated at a temperature of 300 K, and all reactive trajectories proceeded through the carbonyl oxide Criegee intermediate, CH 2 OO, on both the singlet and triplet PESs. The triplet surface leads to only one product channel, H 2 CO + O( 3 P), while the singlet surface leads to eight product channels with their relative importance as CO + H 2 O > CO + OH + H ∼ H 2 CO + O( 1 D) > HCO + OH ∼ CO 2 + H 2 ∼ CO + H 2 + O( 1 D) > CO 2 + H + H > HCO + O( 1 D) + H. The reaction on the singlet PES is barrierless, consistent with experiment, and the total rate constant on the singlet surface is (0.93 ± 0.22) × 10 -12 cm 3 molecule -1 s -1 in comparison to the recommended experimental rate constant of 3.3 × 10 -12 cm 3 molecule -1 s -1 . The simulation product yields for the singlet PES are compared with experiment, and the most significant differences are for H, CO 2 , and H 2 O. The reaction on the triplet surface is also barrierless, inconsistent with experiment. A discussion is given of the need for future calculations to address (1) the barrier on the triplet PES for 3 CH 2 + 3 O 2 → 3 CH 2 OO, (2) the temperature dependence of the 3 CH 2 + 3 O 2 reaction rate constant and product branching ratios, and (3) the possible non-RRKM dynamics of the 1 CH 2 OO Criegee intermediate.

Low-Temperature Preparation of (111)-oriented Pb(Zr,Ti)O3 Films Using Lattice-Matched (111)SrRuO3/Pt Bottom Electrode by Metal-Organic Chemical Vapor Deposition

NASA Astrophysics Data System (ADS)

Kuwabara, Hiroki; Sumi, Akihiro; Okamoto, Shoji; Hoko, Hiromasa; Cross, Jeffrey S.; Funakubo, Hiroshi

2009-04-01

Pb(Zr0.35Ti0.65)O3 (PZT) films 170 nm thick were prepared at 415 °C by pulsed metal-organic chemical vapor deposition. The (111)-oriented PZT films with local epitaxial growth were obtained on (111)SrRuO3/(111)Pt/TiO2/SiO2/Si substrates and their ferroelectricities were ascertained. Ferroelectricity was improved by postannealing under O2 gas flow up to 550 °C. Larger remanent polarization and better fatigue endurance were obtained using a SrRuO3 top electrode compared to a Pt top electrode for PZT films after annealing at 500 °C.

CuO, MnO2 and Fe2O3 doped biomass ash as silica source for glass production in Thailand

NASA Astrophysics Data System (ADS)

Srisittipokakun, N.; Ruangtaweep, Y.; Rachniyom, W.; Boonin, K.; Kaewkhao, J.

In this research, glass productions from rice husk ash (RHA) and the effect of BaO, CuO, MnO2 and Fe2O3 on physical and optical properties were investigated. All properties were compared with glass made from SiO2 using same preparations. The results show that a higher density and refractive index of BaO, CuO, MnO2 and Fe2O3 doped in RHA glasses were obtained, compared with SiO2 glasses. The optical spectra show no significant difference between both glasses. The color of CuO glasses show blue from the absorption band near 800 nm (2B1g → 2B2g) due to Cu2+ ion in octahedral coordination with a strong tetragonal distortion. The color of MnO2 glasses shows brown from broad band absorption at around 500 nm. This absorption band is assigned to a single allowed 5Eg → 5T2g transition which arises from the Mn3+ ions (3d4 configuration) in octahedral symmetry. The yellow color derives from F2O3 glass due to the homogeneous distribution of Fe3+ (460 nm) and Fe2+ (1050 nm) ions in the glass matrices. Glass production from RHA is possible and is a new option for recycling waste from biomass power plant systems and air pollution reduction.

Electrical conductivity optimization of the Na3AlF6-Al2O3-Sm2O3 molten salts system for Al-Sm intermediate binary alloy production

NASA Astrophysics Data System (ADS)

Liao, Chun-fa; Jiao, Yun-fen; Wang, Xu; Cai, Bo-qing; Sun, Qiang-chao; Tang, Hao

2017-09-01

Metal Sm has been widely used in making Al-Sm magnet alloy materials. Conventional distillation technology to produce Sm has the disadvantages of low productivity, high costs, and pollution generation. The objective of this study was to develop a molten salt electrolyte system to produce Al-Sm alloy directly, with focus on the electrical conductivity and optimal operating conditions to minimize the energy consumption. The continuously varying cell constant (CVCC) technique was used to measure the conductivity for the Na3AlF6-AlF3-LiF-MgF2-Al2O3-Sm2O3 electrolysis medium in the temperature range from 905 to 1055°C. The temperature ( t) and the addition of Al2O3 ( W(Al2O3)), Sm2O3 ( W(Sm2O3)), and a combination of Al2O3 and Sm2O3 into the basic fluoride system were examined with respect to their effects on the conductivity ( κ) and activation energy. The experimental results showed that the molten electrolyte conductivity increases with increasing temperature ( t) and decreases with the addition of Al2O3 or Sm2O3 or both. We concluded that the optimal operation conditions for Al-Sm intermediate alloy production in the Na3AlF6-AlF3-LiF-MgF2-Al2O3-Sm2O3 system are W(Al2O3) + W(Sm2O3) = 3wt%, W(Al2O3): W(Sm2O3) = 7:3, and a temperature of 965 to 995°C, which results in satisfactory conductivity, low fluoride evaporation losses, and low energy consumption.

Ag-doped Co3O4 catalyst derived from heterometallic MOF for syngas production by electrocatalytic reduction of CO2 in water

NASA Astrophysics Data System (ADS)

Zhang, Shi-Yuan; Yang, Yuan-Yuan; Zheng, Yue-Qing; Zhu, Hong-Lin

2018-07-01

Electrocatalytic reduction of CO2 to useful fuels or chemicals is a promising path for carbon recycling. In this study, a novel mixed-metallic MOF [Ag4Co2(pyz)PDC4][Ag2Co(pyz)2PDC2] was synthesized, and it transformed into Ag doped Co3O4 catalyst, which exhibits excellent electro-catalytic performance for reduction of CO2 in water to syngas (H2 + CO). The as-prepared Ag/Co3O4 material exhibits a high selectivity of CO in 0.1 M KHCO3 aqueous solution (CO2 saturated) with the corresponding faradaic efficiency up to 55.6%. Compared with the Ag/Co3O4 electrode, the maximum faradaic efficiency (FE) of CO of pure Co3O4 is 21.3% at - 1.8 V vs. SCE. The results show that the presence of Ag can improve the efficiency of CO significantly, thereby inhibiting the production of H2. The stability of the samples can be maintained for more than 10 h at - 1.8 V vs. SCE. The ratio of production between H2 and CO can be controlled by varying the potential values.

Synthesis of Nanoscale CaO-Al2O3-SiO2-H2O and Na2O-Al2O3-SiO2-H2O Using the Hydrothermal Method and Their Characterization

PubMed Central

Yang, Jingbin; Li, Dongxu; Fang, Yuan

2017-01-01

C-A-S-H (CaO-Al2O3-SiO2-H2O) and N-A-S-H (Na2O-Al2O3-SiO2-H2O) have a wide range of chemical compositions and structures and are difficult to separate from alkali-activated materials. Therefore, it is difficult to analyze their microscopic properties directly. This paper reports research on the synthesis of C-A-S-H and N-A-S-H particles with an average particle size smaller than 300 nm by applying the hydrothermal method. The composition and microstructure of the products with different CaO(Na2O)/SiO2 ratios and curing conditions were characterized using XRD, the RIR method, FTIR, SEM, TEM, and laser particle size analysis. The results showed that the C-A-S-H system products with a low CaO/SiO2 ratio were mainly amorphous C-A-S-H gels. With an increase in the CaO/SiO2 ratio, an excess of Ca(OH)2 was observed at room temperature, while in a high-temperature reaction system, katoite, C4AcH11, and other crystallized products were observed. The katoite content was related to the curing temperature and the content of Ca(OH)2 and it tended to form at a high-temperature and high-calcium environment, and an increase in the temperature renders the C-A-S-H gels more compact. The main products of the N-A-S-H system at room temperature were amorphous N-A-S-H gels and a small amount of sodalite. An increase in the curing temperature promoted the formation of the crystalline products faujasite and zeolite-P. The crystallization products consisted of only zeolite-P in the high-temperature N-A-S-H system and its content were stable above 70%. An increase in the Na2O/SiO2 ratio resulted in more non-bridging oxygen and the TO4 was more isolated in the N-A-S-H structure. The composition and microstructure of the C-A-S-H and N-A-S-H system products synthesized by the hydrothermal method were closely related to the ratio of the raw materials and the curing conditions. The results of this study increase our understanding of the hydration products of alkali-activated materials. PMID

Chemical disorder influence on magnetic state of optimally-doped La0.7Ca0.3MnO3

NASA Astrophysics Data System (ADS)

Rozenberg, E.; Auslender, M.; Shames, A. I.; Jung, G.; Felner, I.; Tsindlekht, M. I.; Mogilyansky, D.; Sominski, E.; Gedanken, A.; Mukovskii, Ya. M.; Gorodetsky, G.

2011-10-01

X-band electron magnetic resonance and dc/ac magnetic measurements have been employed to study the effects of chemical disorder on magnetic ordering in bulk and nanometer-sized single crystals and bulk ceramics of optimally-doped La0.7Ca0.3MnO3 manganite. The magnetic ground state of bulk samples appeared to be ferromagnetic with the lower Curie temperature and higher magnetic homogeneity in the vicinity of the ferromagnetic-paramagnetic phase transition in the crystal, as compared with those characteristics in the ceramics. The influence of technological driven "macroscopic" fluctuations of Ca-dopant level in crystal and "mesoscopic" disorder within grain boundary regions in ceramics was proposed to be responsible for these effects. Surface spin disorder together with pronounced inter-particle interactions within agglomerated nano-sample results in well defined core/shell spin configuration in La0.7Ca0.3MnO3 nano-crystals. The analysis of the electron paramagnetic resonance data enlightened the reasons for the observed difference in the magnetic order. Lattice effects dominate the first-order nature of magnetic phase transition in bulk samples. However, mesoscale chemical disorder seems to be responsible for the appearance of small ferromagnetic polarons in the paramagnetic state of bulk ceramics. The experimental results and their analysis indicate that a chemical/magnetic disorder has a strong impact on the magnetic state even in the case of mostly stable optimally hole-doped manganites.

Investigation of La1−xSrxCrO3−∂ (x ~ 0.1) as Membrane for Hydrogen Production

PubMed Central

Larring, Yngve; Vigen, Camilla; Ahouanto, Florian; Fontaine, Marie-Laure; Peters, Thijs; Smith, Jens B.; Norby, Truls; Bredesen, Rune

2012-01-01

Various inorganic membranes have demonstrated good capability to separate hydrogen from other gases at elevated temperatures. Hydrogen-permeable, dense, mixed proton-electron conducting ceramic oxides offer superior selectivity and thermal stability, but chemically robust candidates with higher ambipolar protonic and electronic conductivity are needed. In this work, we present for the first time the results of various investigations of La1−xSrxCrO3−∂ membranes for hydrogen production. We aim in particular to elucidate the material’s complex transport properties, involving co-ionic transport of oxide ions and protons, in addition to electron holes. This opens some new possibilities for efficient heat and mass transfer management in the production of hydrogen. Conductivity measurements as a function of pH2 at constant pO2 exhibit changes that reveal a significant hydration and presence of protons. The flux and production of hydrogen have been measured under different chemical gradients. In particular, the effect of water vapor in the feed and permeate gas stream sides was investigated with the aim of quantifying the ratio of hydrogen production by hydrogen flux from feed to permeate and oxygen flux the opposite way (“water splitting”). Deuterium labeling was used to unambiguously prove flux of hydrogen species. PMID:24958299

The influence of α-Al2O3 addition on microstructure, mechanical and formaldehyde adsorption properties of fly ash-based geopolymer products.

PubMed

Huang, Yi; Han, Minfang

2011-10-15

Fly ash-based geopolymer with α-Al(2)O(3) addition were synthesized and used to remove formaldehyde from indoor air. The microstructure, mechanical and formaldehyde adsorption properties of the geopolymer products obtained were investigated. The results showed that α-Al(2)O(3) addition with appropriate amount (such as 5 wt%) increased the geopolymerization extent, resulting in the increase of surface area and compressive strength. In addition, the improvement of structural ordering level for geopolymer sample with 5 wt% α-Al(2)O(3) addition was found through FTIR analysis. By contrast, excessive addition (such as 10 wt%) had the opposite effect. The test of formaldehyde adsorption capacity confirmed that fly ash-based geopolymer product exhibited much better property of adsorbing indoor formaldehyde physically and chemically than fly ash itself. The surface area was an important but not unique factor influencing the adsorption capacity of geopolymers. Copyright © 2011 Elsevier B.V. All rights reserved.

β-Ga2O3 versus ε-Ga2O3: Control of the crystal phase composition of gallium oxide thin film prepared by metal-organic chemical vapor deposition

NASA Astrophysics Data System (ADS)

Zhuo, Yi; Chen, Zimin; Tu, Wenbin; Ma, Xuejin; Pei, Yanli; Wang, Gang

2017-10-01

Gallium oxide thin films of β and ε phase were grown on c-plane sapphire using metal-organic chemical vapor deposition and the phase compositions were analyzed using X-ray diffraction. The epitaxial phase diagram was constructed as a function of the growth temperature and VI/III ratio. A low growth temperature and low VI/III ratio were beneficial for the formation of hexagonal-type ε-Ga2O3. Further structure analysis revealed that the epitaxial relationship between ε-Ga2O3 and c-plane sapphire is ε-Ga2O3 (0001) || Al2O3 (0001) and ε-Ga2O3 || Al2O3 . The structural evolution of the mixed-phase sample during film thickening was investigated. By reducing the growth rate, the film evolved from a mixed phase to the energetically favored ε phase. Based on these results, a Ga2O3 thin film with a phase-pure ε-Ga2O3 upper layer was successfully obtained.

Reaction Paths and Chemical Activation Reactions of 2-Methyl-5-Furanyl Radical with 3O2.

PubMed

Hudzik, Jason M; Bozzelli, Joseph W

2017-10-05

Interest in high-energy substituted furans has been increasing due to their occurrence in biofuel production and their versatility in conversion to other useful products. Methylfurans are the simplest substituted furans and understanding their reaction pathways, thermochemical properties, including intermediate species stability, and chemical kinetics would aid in the study of larger furans. Furan ring C-H bonds have been shown to be extremely strong, approximately 120 kcal mol -1 , due in part to the placement of the oxygen atom and aromatic-like resonance, both within the ring. The thermochemistry and kinetics of the oxidation of 2-methyfuran radical at position 5 of the furan ring, 2-methyl-5-furanyl radical (2MF5j), is analyzed. The resulting chemically activated species, 2MF5OOj radical, has a well depth of 51 kcal mol -1 below the 2MF5j + O 2 reactants; this is 4-5 kcal mol -1 deeper than that of phenyl and vinyl radical plus O 2 , with both of these reactions known to undergo chain branching. Important, low-energy reaction pathways include chain branching dissociations, intramolecular abstractions, group transfers, and radical oxygen additions. Enthalpies of formation, entropies, and heat capacities for the stable molecules, radicals, and transition-state species are analyzed using computational methods. Calculated ΔH ° f 298 values were determined using an isodesmic work reaction from the CBS-QB3 composite method. Elementary rate parameters are from saddle point transition-state structures and compared to variational transition-state analysis for the barrierless reactions. Temperature- and pressure-dependent rate constants which are calculated using QRRK and master equation analysis is used for falloff and stabilization.

ALD Produced B{sub 2}O{sub 3}, Al{sub 2}O{sub 3} and TiO{sub 2} Coatings on Gd{sub 2}O{sub 3} Burnable Poison Nanoparticles and Carbonaceous TRISO Coating Layers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Weimer, Alan

2012-11-26

This project will demonstrate the feasibility of using atomic layer deposition (ALD) to apply ultrathin neutron-absorbing, corrosion-resistant layers consisting of ceramics, metals, or combinations thereof, on particles for enhanced nuclear fuel pellets. Current pellet coating technology utilizes chemical vapor deposition (CVD) in a fluidized bed reactor to deposit thick, porous layers of C (or PyC) and SiC. These graphitic/carbide materials degrade over time owing to fission product bombardment, active oxidation, thermal management issues, and long-term irradiation effects. ALD can be used to deposit potential ceramic barrier materials of interest, including ZrO{sub 2}, Y{sub 2}O{sub 3}:ZrO{sub 2} (YSZ), Al{sub 2}O{sub 3},more » and TiO{sub 2}, or neutron-absorbing materials, namely B (in BN or B{sub 2}O{sub 3}) and Gd (in Gd{sub 2}O{sub 3}). This project consists of a two-pronged approach to integrate ALD into the next-generation nuclear plant (NGNP) fuel pellet manufacturing process:« less

Relationship between fabrication method and chemical stability of Ni-BaZr0.8Y0.2O3-δ membrane

NASA Astrophysics Data System (ADS)

Fang, Shumin; Wang, Siwei; Brinkman, Kyle S.; Su, Qing; Wang, Haiyan; Chen, Fanglin

2015-03-01

NiO effectively promotes the sintering of highly refractory Y-doped BaZrO3 (BZY) through the formation of BaY2NiO5, providing a simple and cost-effective method for the fabrication of dense BZY electrolyte and Ni-BZY hydrogen separation membrane at ∼1400 °C. Unfortunately, insulating BaCO3 and Y2O3 phases formed on the surface of BZY and Ni-BZY prepared by solid state reaction method with NiO after annealing in wet CO2. Ni-BZY membranes prepared from different methods suffered different degree of performance loss in wet H2 at 900 °C. The chemical instability of Ni-BZY is attributed to the formation of a secondary phase (BaY2O4) generated from the reduction of BaY2NiO5 in H2 during the sintering process. Both BaY2O4 and BaY2NiO5 react with H2O, and CO2 at elevated temperatures, generating insulating Ba(OH)2 and BaCO3 phases, respectively. The less BaY2O4 is formed in the fabrication process, the better chemical stability the Ni-BZY membranes possess. Therefore, a new Ni-BZY membrane is prepared through a judicial combination of BZY powders prepared from combined EDTA-citric and solid state reaction methods, and demonstrates exceptional chemical stability in H2O and CO2, enabling stable and even improved hydrogen flux in wet 50% CO2 at 900 °C.

Chemical pretreatment of lignocellulosic agroindustrial waste for methane production.

PubMed

Pellera, Frantseska-Maria; Gidarakos, Evangelos

2018-01-01

This study investigates the effect of different chemical pretreatments on the solubilization and the degradability of different solid agroindustrial waste, namely winery waste, cotton gin waste, olive pomace and juice industry waste. Eight different reagents were investigated, i.e. sodium hydroxide (NaOH), sodium bicarbonate (NaHCO 3 ), sodium chloride (NaCl), citric acid (H 3 Cit), acetic acid (AcOH), hydrogen peroxide (H 2 O 2 ), acetone (Me 2 CO) and ethanol (EtOH), under three condition sets resulting in treatments of varying intensity, depending on process duration, reagent dosage and temperature. Results indicated that chemical pretreatment under more severe conditions is more effective on the solubilization of lignocellulosic substrates, such as those of the present study and among the investigated reagents, H 3 Cit, H 2 O 2 and EtOH appeared to be the most effective to this regard. At the same time, although chemical pretreatment in general did not improve the methane potential of the substrates, moderate to high severity conditions were found to generally be the most satisfactory in terms of methane production from pretreated materials. In fact, moderate severity treatments using EtOH for winery waste, H 3 Cit for olive pomace and H 2 O 2 for juice industry waste and a high severity treatment with EtOH for cotton gin waste, resulted in maximum specific methane yield values. Ultimately, the impact of pretreatment parameters on the different substrates seems to be dependent on their characteristics, in combination with the specific mode of action of each reagent. The overall energy balance of such a system could probably be improved by using lower operating powers and higher solid to liquid ratios. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biotechnological Production of Dimethoxyflavonoids Using a Fusion Flavonoid O-Methyltransferase Possessing Both 3'- and 7-O-Methyltransferase Activities.

PubMed

Lee, Danbi; Park, Hye Lin; Lee, Sang-Won; Bhoo, Seong Hee; Cho, Man-Ho

2017-05-26

Although they are less abundant in nature, methoxyflavonoids have distinct physicochemical and pharmacological properties compared to common nonmethylated flavonoids. Thus, enzymatic conversion and biotransformation using genetically engineered microorganisms of flavonoids have been attempted for the efficient production of methoxyflavonoids. Because of their regiospecificity, more than two flavonoid O-methyltransferases (FOMTs) and enzyme reactions are required to biosynthesize di(or poly)-methoxyflavonoids. For the one-step biotechnological production of bioactive di-O-methylflavonoids, we generated a multifunctional FOMT fusing a 3'-OMT (SlOMT3) and a 7-OMT (OsNOMT). The SlOMT3/OsNOMT fusion enzyme possessed both 3'- and 7-OMT activities to diverse flavonoid substrates, which were comparable to those of individual SlOMT3 and OsNOMT. The SlOMT3/OsNOMT enzyme also showed 3'- and 7-OMT activity for 7- or 3'-O-methylflavonoids, respectively, suggesting that the fusion enzyme can sequentially methylate flavonoids into di-O-methylflavonoids. The biotransformation of the flavonoids quercetin, luteolin, eriodictyol, and taxifolin using SlOMT3/OsNOMT-transformed Escherichia coli generated corresponding di-O-methylflavonoids, rhamnazin, velutin, 3',7-di-O-methyleriodictyol, and 3',7-di-O-methyltaxifolin, respectively. These results indicate that dimethoxyflavonoids may be efficiently produced from nonmethylated flavonoid precursors through a one-step biotransformation using the engineered E. coli harboring the SlOMT3/OsNOMT fusion gene.

Sharp chemical interface in epitaxial Fe{sub 3}O{sub 4} thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gálvez, S.; Rubio-Zuazo, J., E-mail: rubio@esrf.fr; Salas-Colera, E.

Chemically sharp interface was obtained on single phase single oriented Fe{sub 3}O{sub 4} (001) thin film (7 nm) grown on NiO (001) substrate using oxygen assisted molecular beam epitaxy. Refinement of the atomic structure, stoichiometry, and oxygen vacancies were determined by soft and hard x-ray photoelectron spectroscopy, low energy electron diffraction and synchrotron based X-ray reflectivity, and X-ray diffraction. Our results demonstrate an epitaxial growth of the magnetite layer, perfect iron stoichiometry, absence of oxygen vacancies, and the existence of an intermixing free interface. Consistent magnetic and electrical characterizations are also shown.

UiO-66-NH2 Metal-Organic Framework (MOF) Nucleation on TiO2, ZnO, and Al2O3 Atomic Layer Deposition-Treated Polymer Fibers: Role of Metal Oxide on MOF Growth and Catalytic Hydrolysis of Chemical Warfare Agent Simulants.

PubMed

Lee, Dennis T; Zhao, Junjie; Oldham, Christopher J; Peterson, Gregory W; Parsons, Gregory N

2017-12-27

Metal-organic frameworks (MOFs) chemically bound to polymeric microfibrous textiles show promising performance for many future applications. In particular, Zr-based UiO-66-family MOF-textiles have been shown to catalytically degrade highly toxic chemical warfare agents (CWAs), where favorable MOF/polymer bonding and adhesion are attained by placing a nanoscale metal-oxide layer on the polymer fiber preceding MOF growth. To date, however, the nucleation mechanism of Zr-based MOFs on different metal oxides and how product performance is affected are not well understood. Herein, we provide new insight into how different inorganic nucleation films (i.e., Al 2 O 3 , ZnO, or TiO 2 ) conformally coated on polypropylene (PP) nonwoven textiles via atomic layer deposition (ALD) influence the quality, overall surface area, and the fractional yield of UiO-66-NH 2 MOF crystals solvothermally grown on fiber substrates. Of the materials explored, we find that TiO 2 ALD layers lead to the most effective overall MOF/fiber adhesion, uniformity, and a rapid catalytic degradation rate for a CWA simulant, dimethyl p-nitrophenyl phosphate (DMNP) with t 1/2 = 15 min, 580-fold faster than the catalytic performance of untreated PP textiles. Interestingly, compared to ALD TiO 2 and Al 2 O 3 , ALD ZnO induces a larger MOF yield in solution and mass loading on PP fibrous mats. However, this larger MOF yield is ascribed to chemical instability of the ZnO layer under MOF formation condition, leading to Zn 2+ ions that promote further homogeneous MOF growth. Insights presented here improve understanding of compatibility between active MOF materials and substrate surfaces, which we believe will help advanced MOF composite materials for a variety of useful functions.

AES study on the chemical composition of ferroelectric BaTiO3 thin films RF sputter-deposited on silicon

NASA Technical Reports Server (NTRS)

Dharmadhikari, V. S.; Grannemann, W. W.

1983-01-01

AES depth profiling data are presented for thin films of BaTiO3 deposited on silicon by RF sputtering. By profiling the sputtered BaTiO3/silicon structures, it was possible to study the chemical composition and the interface characteristics of thin films deposited on silicon at different substrate temperatures. All the films showed that external surface layers were present, up to a few tens of angstroms thick, the chemical composition of which differed from that of the main layer. The main layer had stable composition, whereas the intermediate film-substrate interface consisted of reduced TiO(2-x) oxides. The thickness of this intermediate layer was a function of substrate temperature. All the films showed an excess of barium at the interface. These results are important in the context of ferroelectric phenomena observed in BaTiO3 thin films.

Efficient 2-Nitrophenol Chemical Sensor Development Based on Ce2O3 Nanoparticles Decorated CNT Nanocomposites for Environmental Safety

PubMed Central

Hussain, Mohammad M.; Rahman, Mohammed M.; Asiri, Abdullah M.

2016-01-01

Ce2O3 nanoparticle decorated CNT nanocomposites (Ce2O3.CNT NCs) were prepared by a wet-chemical method in basic medium. The Ce2O3.CNT NCs were examined using FTIR, UV/Vis, Field-Emission Scanning Electron Microscopy (FESEM), X-ray electron dispersive spectroscopy (XEDS), X-ray photoelectron spectroscopy (XPS), and powder X-ray diffraction (XRD). A selective 2-nitrophenol (2-NP) sensor was developed by fabricating a thin-layer of NCs onto a flat glassy carbon electrode (GCE, surface area = 0.0316 cm2). Higher sensitivity including linear dynamic range (LDR), long-term stability, and enhanced electrochemical performances towards 2-NP were achieved by a reliable current-voltage (I-V) method. The calibration curve was found linear (R2 = 0.9030) over a wide range of 2-NP concentration (100 pM ~ 100.0 mM). Limit of detection (LOD) and sensor sensitivity were calculated based on noise to signal ratio (~3N/S) as 60 ± 0.02 pM and 1.6×10−3 μAμM-1cm-2 respectively. The Ce2O3.CNT NCs synthesized by a wet-chemical process is an excellent way of establishing nanomaterial decorated carbon materials for chemical sensor development in favor of detecting hazardous compounds in health-care and environmental fields at broad-scales. Finally, the efficiency of the proposed chemical sensors can be applied and utilized in effectively for the selective detection of toxic 2-NP component in environmental real samples with acceptable and reasonable results. PMID:27973600

Efficient 2-Nitrophenol Chemical Sensor Development Based on Ce2O3 Nanoparticles Decorated CNT Nanocomposites for Environmental Safety.

PubMed

Hussain, Mohammad M; Rahman, Mohammed M; Asiri, Abdullah M

2016-01-01

Ce2O3 nanoparticle decorated CNT nanocomposites (Ce2O3.CNT NCs) were prepared by a wet-chemical method in basic medium. The Ce2O3.CNT NCs were examined using FTIR, UV/Vis, Field-Emission Scanning Electron Microscopy (FESEM), X-ray electron dispersive spectroscopy (XEDS), X-ray photoelectron spectroscopy (XPS), and powder X-ray diffraction (XRD). A selective 2-nitrophenol (2-NP) sensor was developed by fabricating a thin-layer of NCs onto a flat glassy carbon electrode (GCE, surface area = 0.0316 cm2). Higher sensitivity including linear dynamic range (LDR), long-term stability, and enhanced electrochemical performances towards 2-NP were achieved by a reliable current-voltage (I-V) method. The calibration curve was found linear (R2 = 0.9030) over a wide range of 2-NP concentration (100 pM ~ 100.0 mM). Limit of detection (LOD) and sensor sensitivity were calculated based on noise to signal ratio (~3N/S) as 60 ± 0.02 pM and 1.6×10-3 μAμM-1cm-2 respectively. The Ce2O3.CNT NCs synthesized by a wet-chemical process is an excellent way of establishing nanomaterial decorated carbon materials for chemical sensor development in favor of detecting hazardous compounds in health-care and environmental fields at broad-scales. Finally, the efficiency of the proposed chemical sensors can be applied and utilized in effectively for the selective detection of toxic 2-NP component in environmental real samples with acceptable and reasonable results.

Physical and chemical effects on crystalline H2O2 induced by 20 keV protons.

PubMed

Loeffler, M J; Baragiola, R A

2009-03-21

We present laboratory studies on radiation chemistry, sputtering, and amorphization of crystalline H(2)O(2) induced by 20 keV protons at 80 K. We used infrared spectroscopy to identify H(2)O, O(3), and possibly HO(3), measure the fluence dependence of the fraction of crystalline and amorphous H(2)O(2) and of the production of H(2)O and destruction of H(2)O(2). Furthermore, using complementary techniques, we observe that the sputtering yield depends on fluence due to the buildup of O(2) radiation products in the sample. In addition, we find that the effective cross sections for the destruction of hydrogen peroxide and the production of water are very high compared to radiation chemical processes in water even though the fluence dependence of amorphization is nearly the same for the two materials. This result is consistent with a model of fast cooling of a liquid track produced by each projectile ion rather than with the disorder produced by the formation of radiolytic products.

Hydrogen Radicals, Nitrogen Radicals, and the Production of O3 in the Upper Troposphere

NASA Technical Reports Server (NTRS)

Wennberg, P. O.; Hanisco, T. F.; Jaegle, L.; Jacob, D. J.; Hintsa, E. J.; Lanzendorf, E. J.; Anderson, J. G.; Gao, R.-S.; Keim, E. R.; Donnelly, S. G.;

Hierarchical Cu2O foam/g-C3N4 photocathode for photoelectrochemical hydrogen production

NASA Astrophysics Data System (ADS)

Ma, Xinzhou; Zhang, Jingtao; Wang, Biao; Li, Qiuguo; Chu, Sheng

2018-01-01

Solar photoelectrochemical (PEC) hydrogen production is a promising way for solving energy and environment problems. Earth-abundant Cu2O is a potential light absorber for PEC hydrogen production. In this article, hierarchical porous Cu2O foams are prepared by thermal oxidation of the electrochemically deposited Cu foams. PEC performances of the Cu2O foams are systematically studied and discussed. Benefiting from their higher light harvesting and more efficient charge separation, the Cu2O foams demonstrate significantly enhanced photocurrents and photostability compared to their film counterparts. Moreover, by integrating g-C3N4, hierarchical Cu2O foam/g-C3N4 composites are prepared with further improved photocurrent and photostability, appearing to be potential photocathodes for solar PEC hydrogen production. This study may provide a new and useful insight for the development of Cu2O-based photocathodes for PEC hydrogen production.

Growth mechanism and elemental distribution of beta-Ga2O3 crystalline nanowires synthesized by cobalt-assisted chemical vapor deposition.

PubMed

Wang, Hui; Lan, Yucheng; Zhang, Jiaming; Crimp, Martin A; Ren, Zhifeng

2012-04-01

Long beta-Ga2O3 crystalline nanowires are synthesized on patterned silicon substrates using chemical vapor deposition technique. Advanced electron microscopy indicates that the as-grown beta-Ga2O3 nanowires are consisted of poly-crystalline (Co, Ga)O tips and straight crystalline beta-Ga2O3 stems. The catalytic cobalt not only locates at the nanowire tips but diffuses into beta-Ga2O3 nanowire stems several ten nanometers. A solid diffusion growth mechanism is proposed based on the spatial elemental distribution along the beta-Ga2O3 nanowires at nanoscale.

Double Z-scheme ZnO/ZnS/g-C3N4 ternary structure for efficient photocatalytic H2 production

NASA Astrophysics Data System (ADS)

Dong, Zhifang; Wu, Yan; Thirugnanam, Natarajan; Li, Gonglin

2018-02-01

In the present work, a novel ZnO/ZnS/g-C3N4 ternary nanocomposite with double Z-scheme heterojunction has been designed via a two-step facile chemical conversion route. The spherical ZnS nanoparticles were uniformly loaded onto ZnO nanoflowers surface. And then the ZnO/ZnS nanocomposite was further hybridized with g-C3N4 nanosheets. Ternary ZnO/ZnS/g-C3N4 nanocomposite displays the largest specific surface area (about 76.2 m2/g), which provides plentiful activated sites for photocatalytic reaction. Furthermore, the ternary material exhibits the highest methylene blue photodegradation rate of about 0.0218 min-1 and the optimum photocatalytic H2 production (1205 μmol/g) over water splitting at 4 h under solar light irradiation. Moreover, it showed the highest photocurrent effect and the minimum charge-transfer resistance. These results implied that the higher photoactivity of ZnO/ZnS/g-C3N4 nanocomposite could be attributed to the multi-steps charge transfer and effective electron-hole separation in the double Z-scheme system.

SME observations of O2(1 Delta g) nightglow - An assessment of the chemical production mechanisms

NASA Technical Reports Server (NTRS)

Howell, Colin D.; Michelangeli, Diane V.; Allen, Mark; Yung, Yuk L.; Thomas, Ronald J.

1990-01-01

Solar Mesosphere Explorer (SME) observations of the 3 a.m. 1.27 micron nightglow at 45 N latitude are reported. From the deduced volume emission rates, the O2(a 1 Delta g) nighttime production rates for the 80-100 km altitude range are derived. Utilizing the mean SME-acquired 3 p.m. ozone profile for the same latitude and time period and an updated photochemical model, nighttime O, O3, H, OH, HO2, and H2O2 profiles are determined. These are used in calculating the rates of reactions which are sufficiently exothermic to produce O2(1 Delta) or excited states of OH or HO2, which could transfer their energy to O2 to form O2(1 Delta). Yields of O2(1 Delta) based on published laboratory and observational studies are used to find that the sum of two reaction sequences can approximate the SME measurements: (1) O + O + M and (2) H + O3 followed by OH-asterisk + O2.

The chemical, mechanical, and physical properties of 3D printed materials composed of TiO2-ABS nanocomposites

PubMed Central

Skorski, Matthew R.; Esenther, Jake M.; Ahmed, Zeeshan; Miller, Abigail E.; Hartings, Matthew R.

2016-01-01

Abstract To expand the chemical capabilities of 3D printed structures generated from commercial thermoplastic printers, we have produced and printed polymer filaments that contain inorganic nanoparticles. TiO2 was dispersed into acrylonitrile butadiene styrene (ABS) and extruded into filaments with 1.75 mm diameters. We produced filaments with TiO2 compositions of 1, 5, and 10% (kg/kg) and printed structures using a commercial 3D printer. Our experiments suggest that ABS undergoes minor degradation in the presence of TiO2 during the different processing steps. The measured mechanical properties (strain and Young’s modulus) for all of the composites are similar to those of structures printed from the pure polymer. TiO2 incorporation at 1% negatively affects the stress at breaking point and the flexural stress. Structures produced from the 5 and 10% nanocomposites display a higher breaking point stress than those printed from the pure polymer. TiO2 within the printed matrix was able to quench the intrinsic fluorescence of the polymer. TiO2 was also able to photocatalyze the degradation of a rhodamine 6G in solution. These experiments display chemical reactivity in nanocomposites that are printed using commercial 3D printers, and we expect that our methodology will help to inform others who seek to incorporate catalytic nanoparticles in 3D printed structures. PMID:27375367

The chemical, mechanical, and physical properties of 3D printed materials composed of TiO2-ABS nanocomposites.

PubMed

Skorski, Matthew; Esenther, Jake; Ahmed, Zeeshan; Miller, Abigail E; Hartings, Matthew R

To expand the chemical capabilities of 3D printed structures generated from commercial thermoplastic printers, we have produced and printed polymer filaments that contain inorganic nanoparticles. TiO 2 was dispersed into acrylonitrile butadiene styrene (ABS) and extruded into filaments with 1.75 mm diameters. We produced filaments with TiO 2 compositions of 1%, 5%, and 10% (kg/kg) and printed structures using a commercial 3D printer. Our experiments suggest that ABS undergoes minor degradation in the presence of TiO 2 during the different processing steps. The measured mechanical properties (strain and Young's modulus) for all of the composites are similar to those of structures printed from the pure polymer. TiO 2 incorporation at 1% negatively affects the stress at breaking point and the flexural stress. Structures produced from the 5 and 10% nanocomposites display a higher breaking point stress than those printed from the pure polymer. TiO 2 within the printed matrix was able to quench the intrinsic fluorescence of the polymer. TiO 2 was also able to photocatalyze the degradation of a rhodamine 6G in solution. These experiments display chemical reactivity in nanocomposites that are printed using commercial 3D printers, and we expect that our methodology will help to inform others who seek to incorporate catalytic nanoparticles in 3D printed structures.

The chemical, mechanical, and physical properties of 3D printed materials composed of TiO2-ABS nanocomposites

NASA Astrophysics Data System (ADS)

Skorski, Matthew R.; Esenther, Jake M.; Ahmed, Zeeshan; Miller, Abigail E.; Hartings, Matthew R.

2016-01-01

To expand the chemical capabilities of 3D printed structures generated from commercial thermoplastic printers, we have produced and printed polymer filaments that contain inorganic nanoparticles. TiO2 was dispersed into acrylonitrile butadiene styrene (ABS) and extruded into filaments with 1.75 mm diameters. We produced filaments with TiO2 compositions of 1, 5, and 10% (kg/kg) and printed structures using a commercial 3D printer. Our experiments suggest that ABS undergoes minor degradation in the presence of TiO2 during the different processing steps. The measured mechanical properties (strain and Young's modulus) for all of the composites are similar to those of structures printed from the pure polymer. TiO2 incorporation at 1% negatively affects the stress at breaking point and the flexural stress. Structures produced from the 5 and 10% nanocomposites display a higher breaking point stress than those printed from the pure polymer. TiO2 within the printed matrix was able to quench the intrinsic fluorescence of the polymer. TiO2 was also able to photocatalyze the degradation of a rhodamine 6G in solution. These experiments display chemical reactivity in nanocomposites that are printed using commercial 3D printers, and we expect that our methodology will help to inform others who seek to incorporate catalytic nanoparticles in 3D printed structures.

(111)-oriented Pb(Zr ,Ti)O3 films deposited on SrRuO3/Pt electrodes: Reproducible preparation by metal organic chemical vapor deposition, top electrode influence, and reliability

NASA Astrophysics Data System (ADS)

Menou, Nicolas; Funakubo, Hiroshi

2007-12-01

(111)-textured Pb(Zr0.4Ti0.6)O3 films (thickness of ˜120nm) were deposited on (111)-oriented SrRuO3 bottom electrodes by pulse metal organic chemical vapor deposition (MOCVD). PZT single phase was evidenced over a large range of Pb precursor input rate into the MOCVD chamber. In this process window, the good control of the (111) texture of PZT films was confirmed. It is shown that the control of both the composition and orientation of PZT films leads to reproducible electric properties (Pr, Vc, resistance to fatigue) across the process window. Furthermore, the impact of the top electrode chemical nature, elaboration process, and annealing process upon the electric properties was studied systematically.

Core-shell SrTiO3/graphene structure by chemical vapor deposition for enhanced photocatalytic performance

NASA Astrophysics Data System (ADS)

He, Chenye; Bu, Xiuming; Yang, Siwei; He, Peng; Ding, Guqiao; Xie, Xiaoming

2018-04-01

Direct growth of high quality graphene on the surface of SrTiO3 (STO) was realized through chemical vapor deposition (CVD), to construct few-layer 'graphene shell' on every STO nanoparticle. The STO/graphene composite shows significantly enhanced UV light photocatalytic activity compared with the STO/rGO reference. Mechanism analysis confirms the role of special core-shell structure and chemical bond (Tisbnd C) for rapid interfacial electron transfer and effective electron-hole separation.

Highly Repeatable and Recoverable Phototransistors Based on Multifunctional Channels of Photoactive CdS, Fast Charge Transporting ZnO, and Chemically Durable Al2O3 Layers.

PubMed

Ahn, Cheol Hyoun; Kang, Won Jun; Kim, Ye Kyun; Yun, Myeong Gu; Cho, Hyung Koun

2016-06-22

Highly repeatable and recoverable phototransistors were explored using a "multifunctional channels" structure with multistacked chalcogenide and oxide semiconductors. These devices were made of (i) photoactive CdS (with a visible band gap), (ii) fast charge transporting ZnO (with a high field-effect mobility), and (iii) a protection layer of Al2O3 (with high chemical durability). The CdS TFT without the Al2O3 protection layer did not show a transfer curve due to the chemical damage that occurred on the ZnO layer during the chemical bath deposition (CBD) process used for CdS deposition. Alternatively, compared to CdS phototransistors with long recovery time and high hysteresis (ΔVth = 19.5 V), our "multi-functional channels" phototransistors showed an extremely low hysteresis loop (ΔVth = 0.5V) and superior photosensitivity with repeatable high photoresponsivity (52.9 A/W at 400 nm). These improvements are likely caused by the physical isolation of the sensing region and charge transport region by the insertion of the ultrathin Al2O3 layer. This approach successfully addresses some of the existing problems in CdS phototransistors, such as the high gate-interface trap site density and high absorption of molecular oxygen, which originate from the polycrystalline CdS.

SmNiO3/NdNiO3 thin film multilayers

NASA Astrophysics Data System (ADS)

Girardot, C.; Pignard, S.; Weiss, F.; Kreisel, J.

2011-06-01

Rare earth nickelates RENiO3 (RE =rare earth), which attract interest due to their sharp metal-insulator phase transition, are instable in bulk form due to the necessity of an important oxygen pressure to stabilize Ni in its 3+ state of oxidation. Here, we report the stabilization of RE nickelates in [(SmNiO3)t/(NdNiO3)t]n thin film multilayers, t being the thickness of layers alternated n times. Both bilayers and multilayers have been deposited by metal-organic chemical vapor deposition. The multilayer structure and the presence of the metastable phases SmNiO3 and NdNiO3 are evidenced from by x-ray and Raman scattering. Electric measurements of a bilayer structure further support the structural quality of the embedded RE nickelate layers.

Diameter Tuning of β-Ga2O3 Nanowires Using Chemical Vapor Deposition Technique.

PubMed

Kumar, Mukesh; Kumar, Vikram; Singh, R

2017-12-01

Diameter tuning of [Formula: see text]-Ga 2 O 3 nanowires using chemical vapor deposition technique have been investigated under various experimental conditions. Diameter of root grown [Formula: see text]-Ga 2 O 3 nanowires having monoclinic crystal structure is tuned by varying separation distance between metal source and substrate. Effect of gas flow rate and mixer ratio on the morphology and diameter of nanowires has been studied. Nanowire diameter depends on growth temperature, and it is independent of catalyst nanoparticle size at higher growth temperature (850-900 °C) as compared to lower growth temperature (800 °C). These nanowires show changes in structural strain value with change in diameter. Band-gap of nanowires increases with decrease in the diameter.

Improving the production of acetyl-CoA-derived chemicals in Escherichia coli BL21(DE3) through iclR and arcA deletion.

PubMed

Liu, Min; Ding, Yamei; Chen, Hailin; Zhao, Zhe; Liu, Huizhou; Xian, Mo; Zhao, Guang

2017-01-07

Acetyl-CoA-derived chemicals are suitable for multiple applications in many industries. The bio-production of these chemicals has become imperative owing to the economic and environmental problems. However, acetate overflow is the major drawback for acetyl-CoA-derived chemicals production. Approaches for overcoming acetate overflow may be beneficial for the production of acetyl-CoA-derived chemicals. In this study, a transcriptional regulator iclR was knocked out in E.coli BL21(DE3) to overcome acetate overflow and improve the chemicals production. Two important acetyl-CoA-derived chemicals, phloroglucinol (PG) and 3-hydroxypropionate (3HP) were used to evaluate it. It is revealed that knockout of iclR significantly increased expressions of aceBAK operon. The cell yields and glucose utilization efficiencies were higher than those of control strains. The acetate concentrations were decreased by more than 50% and the productions of PG and 3HP were increased more than twice in iclR mutants. The effects of iclR knockout on cell physiology, cell metabolism and production of acetyl-CoA-derived chemicals were similar to those of arcA knockout in our previous study. However, the arcA-iclR double mutants couldn't gain higher productions of PG and 3HP. The mechanisms are unclear and needed to be resolved in future. Knockout of iclR significantly increased gene expression of aceBAK operon and concomitantly activated glyoxylate pathway. This genetic modification may be a good way to overcome acetate overflow, and improve the production of a wide range of acetyl-CoA-derived chemicals.

Chemicals from ethanol: the acetone synthesis from ethanol employing Ce0.75Zr0.25O2, ZrO2 and Cu/ZnO/Al2O3.

PubMed

Rodrigues, Clarissa Perdomo; Zonetti, Priscila da Costa; Appel, Lucia Gorenstin

2017-04-04

Acetone is an important solvent and widely used in the synthesis of drugs and polymers. Currently, acetone is mainly generated by the Cumene Process, which employs benzene and propylene as fossil raw materials. Phenol is a co-product of this synthesis. However, this ketone can be generated from ethanol (a renewable feedstock) in one-step. The aim of this work is to describe the influence of physical-chemical properties of three different catalysts on each step of this reaction. Furthermore, contribute to improve the description of the mechanism of this synthesis. The acetone synthesis from ethanol was studied employing Cu/ZnO/Al 2 O 3 , Ce 0.75 Zr 0.25 O 2 and ZrO 2 . It was verified that the acidity of the catalysts needs fine-tuning in order to promote the oxygenate species adsorption and avoid the dehydration of ethanol. The higher the reducibility and the H 2 O dissociation activity of the catalysts are, the higher the selectivity to acetone is. In relation to the oxides, these properties are associated with the presence of O vacancies. The H 2 generation, which occurs during the TPSR, indicates the redox character of this synthesis. The main steps of the acetone synthesis from ethanol are the generation of acetaldehyde, the oxidation of this aldehyde to acetate species (which reduces the catalyst), the H 2 O dissociation, the oxidation of the catalyst producing H 2 , and, finally, the ketonization reaction. These pieces of information will support the development of active catalysts for not only the acetone synthesis from ethanol, but also the isobutene and propylene syntheses in which this ketone is an intermediate. Graphical abstract Acetone from ethanol.

Mixed conduction and chemical diffusion in a Pb(Zr0.53,Ti0.47)O3 buried capacitor structure

NASA Astrophysics Data System (ADS)

Donnelly, Niall J.; Randall, Clive A.

2010-02-01

Impedance spectroscopy is performed on a buried capacitor structure composed of a PZT-0.75% Nb ceramic with platinum electrodes. The ionic and electronic conductivities (σion,σelec) are extracted from the impedance spectra using an equivalent circuit based on the premise of mixed conduction. In the temperature range 500-700 °C, a change in local pO2 mainly affects σelec, suggesting that the samples are ionically compensated, i.e., [VO••]=[VPb″]. The chemical diffusion coefficient, D˜, is obtained by a conductivity relaxation technique assuming two-dimensional diffusion geometry. In comparison to BaTiO3, or SrTiO3, the chemical diffusivity is found to be relatively high, D˜=2.0×10-4 cm2 s-1 (700 °C, in air).

A Synthesis and Crystal Chemical Study of the Fast Ion Conductor Li7–3xGaxLa3 Zr2O12 with x = 0.08 to 0.84

PubMed Central

2014-01-01

Fast-conducting phase-pure cubic Ga-bearing Li7La3Zr2O12 was obtained using solid-state synthesis methods with 0.08 to 0.52 Ga3+ pfu in the garnet. An upper limit of 0.72 Ga3+ pfu in garnet was obtained, but the synthesis was accompanied by small amounts of La2Zr2O12 and LiGaO3. The synthetic products were characterized by X-ray powder diffraction, electron microprobe and SEM analyses, ICP-OES measurements, and 71Ga MAS NMR spectroscopy. The unit-cell parameter, a0, of the various garnets does not vary significantly as a function of Ga3+ content, with a value of about 12.984(4) Å. Full chemical analyses for the solid solutions were obtained giving: Li7.08Ga0.06La2.93Zr2.02O12, Li6.50Ga0.15La2.96Zr2.05O12, Li6.48Ga0.23La2.93Zr2.04O12, Li5.93Ga0.36La2.94Zr2.01O12, Li5.38Ga0.53La2.96Zr1.99O12, Li4.82Ga0.60La2.96Zr2.00O12, and Li4.53Ga0.72La2.94Zr1.98O12. The NMR spectra are interpreted as indicating that Ga3+ mainly occurs in a distorted 4-fold coordinated environment that probably corresponds to the general 96h crystallographic site of garnet. PMID:24874559

Enhanced photocatalytic hydrogen production from water-ethanol solution by Ruthenium doped La-NaTaO3

NASA Astrophysics Data System (ADS)

Husin, H.; Alam, P. N.; Zaki, M.; Sofyana; Jakfar; Husaini; Hasfita, F.

2018-04-01

The photocatalytic hydrogen production from ethanol aqueous solution, with the use ruthenium doped La-NaTaO3 has been investigated. Ruthenium doped La-NaTaO3 catalysts are prepared by impregnation method. The catalysts are by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The Ru co-catalyst demonstrated from the TEM image shows a good dispersion on the surface of La-C-NaTaO3 with an average particle size between 4-5 nm. The photocatalytic reaction is carried out in a closed reactor with a gas circulation system. The catalytic activity of La-NaTaO3 improved markedly (6.6 times from pure water) when Ru is loaded onto its surface. The hydrogen production is notably enhanced in the presence of ethanol as electron donors. This result is much higher when compared with the rate of hydrogen production in the sample without co- catalysts about 9.4 times higher after Ru deposition from ethanol aqueous solution. Increasing the production of hydrogen on the Ru/La-NaTaO3 closely related to the decrease in recombination between electron-hole pairs.

Self-assembled supramolecular system PDINH on TiO2 surface enhances hydrogen production.

PubMed

Li, Xin; Lv, Xingshuai; Zhang, Qianqian; Huang, Baibiao; Wang, Peng; Qin, Xiaoyan; Zhang, Xiaoyang; Dai, Ying

2018-09-01

Constructing organic-inorganic hybrids is one of the hopeful strategies to improve photocatalyst performance. In this study, perylene-3,4,9,10-tetracarboxylic diimide (PDINH) and commercial TiO 2 P25 are chosen as raw materials to construct a PDINH/TiO 2 organic-inorganic hybrid, which has higher photocatalytic H 2 production activity and photocurrent intensity than pure PDINH and TiO 2 , respectively. The apparent quantum efficiency for H 2 production over 0.5%PDINH/TiO 2 reaches as high as 70.69% using irradiation at 365 nm. Moreover, XRD, DRS, HRTEM, FT-IR, and XPS are used to characterize the crystal structure, optical absorption, morphology, molecular structure, and chemical bonds, as well as the elemental and chemical states of PDINH/TiO 2 organic-inorganic hybrid. The interfaces between PDINH and TiO 2 , which largely determine photocatalytic performance, is also analyzed systematically. Furthermore, charge density difference (Δρ) is used to analyze the electron-ion interactions of PDINH and TiO 2 , and reveals that substantial charge transfer occurs from PDINH to TiO 2 . Copyright © 2018. Published by Elsevier Inc.

Enhanced Electrochemical Performances of Bi2O3/rGO Nanocomposite via Chemical Bonding as Anode Materials for Lithium Ion Batteries.

PubMed

Deng, Zhuo; Liu, Tingting; Chen, Tao; Jiang, Jiaxiang; Yang, Wanli; Guo, Jun; Zhao, Jianqing; Wang, Haibo; Gao, Lijun

2017-04-12

Bismuth oxide/reduced graphene oxide (termed Bi 2 O 3 @rGO) nanocomposite has been facilely prepared by a solvothermal method via introducing chemical bonding that has been demonstrated by Raman and X-ray photoelectron spectroscopy spectra. Tremendous single-crystal Bi 2 O 3 nanoparticles with an average size of ∼5 nm are anchored and uniformly dispersed on rGO sheets. Such a nanostructure results in enhanced electrochemical reversibility and cycling stability of Bi 2 O 3 @rGO composite materials as anodes for lithium ion batteries in comparison with agglomerated bare Bi 2 O 3 nanoparticles. The Bi 2 O 3 @rGO anode material can deliver a high initial capacity of ∼900 mAh/g at 0.1C and shows excellent rate capability of ∼270 mAh/g at 10C rates (1C = 600 mA/g). After 100 electrochemical cycles at 1C, the Bi 2 O 3 @rGO anode material retains a capacity of 347.3 mAh/g with corresponding capacity retention of 79%, which is significantly better than that of bare Bi 2 O 3 material. The lithium ion diffusion coefficient during lithiation-delithiation of Bi 2 O 3 @rGO nanocomposite has been evaluated to be around ∼10 -15 -10 -16 cm 2 /S. This work demonstrates the effects of chemical bonding between Bi 2 O 3 nanoparticles and rGO substrate on enhanced electrochemical performances of Bi 2 O 3 @rGO nanocomposite, which can be used as a promising anode alterative for superior lithium ion batteries.

Destructive adsorption of Diazinon pesticide by activated carbon nanofibers containing Al2O3 and MgO nanoparticles.

PubMed

Behnam, Roghaye; Morshed, Mohammad; Tavanai, Hossein; Ghiaci, Mehran

2013-10-01

We report the destructive adsorption of Diazinon pesticide by porous webs of activated carbon nanofibers containing Al2O3 and MgO nanoparticles. The results show that, the presence of Al2O3 and MgO nanoparticles in the activated carbon nanofibers increases the amount of destructively adsorbed Diazinon pesticide by activated carbon nanofibers. Moreover, type, amount, and specific surface area of metal oxide nanoparticles affect the adsorption rate as well as the total destructively adsorbed Diazinon. Liquid chromatography proved the degradation of Diazinon by chemical reaction with Al2O3 and MgO nanoparticles. Liquid chromatography-mass spectrometry showed that the main product of reaction between Diazinon and the metal oxides is 2-isopropyl-6-methyl-4-pyrimidinol with less toxicity than Diazinon.

Material properties of perovskites in the quasi-ternary system LaFeO3-LaCoO3-LaNiO3

NASA Astrophysics Data System (ADS)

Tietz, F.; Arul Raj, I.; Ma, Q.; Baumann, S.; Mahmoud, A.; Hermann, R. P.

2016-05-01

An overview is presented on the variation of electrical conductivity, oxygen permeation, and thermal expansion coefficient as a function of the composition of perovskites in the quasi-ternary system LaFeO3-LaCoO3-LaNiO3. Powders of thirteen nominal perovskite compositions were synthesized under identical conditions by the Pechini method. The powder X-ray diffraction data of two series, namely La(Ni0.5Fe0.5)1-xCoxO3 and LaNi0.5-xFexCo0.5O3, are presented after the powders had been sintered at 1100 °C for 6 h in air. The measurements revealed a rhombohedral structure for all compositions except LaNi0.5Fe0.5O3 for which 60% rhombohedral and 40% orthorhombic phase was found. The maximum DC electrical conductivity value of the perovskites at 800 °C was 1229 S cm-1 for the composition LaCoO3 and the minimum was 91 S cm-1 for the composition LaCo0.5Fe0.5O3. The oxygen permeation of samples with promising conductivities at 800 °C was one order of magnitude lower than that of La0.6Sr0.4Co0.8Fe0.2O3 (LSCF). The highest value of 0.017 ml cm-2 min-1 at 950 °C was obtained with LaNi0.5Co0.5O3. The coefficients of thermal expansion varied in the range of 13.2×10-6 K-1 and 21.9×10-6 K-1 for LaNi0.5Fe0.5O3 and LaCoO3, respectively. 57Fe Mössbauer spectroscopy was used as probe for the oxidation states, local environment and magnetic properties of iron ions as a function of chemical composition. The substitution had a great influence on the chemical properties of the materials.

Hydrogen Radicals, Nitrogen Radicals, and the Production of O3 in the Upper Troposphere

NASA Technical Reports Server (NTRS)

Wennberg, P. O.; Hanisco, T. F.; Jaegle, L.; Jacob, D. J.; Hintsa, E. J.; Lanzendorf, E. J.; Anderson, J. G.; Gao, R.-S.; Keim, E. R.; Donnelly, S. G.;

Wet chemical techniques for passivation of YBa2Cu3O7(7-x)

NASA Technical Reports Server (NTRS)

Vasquez, R. P.; Foote, M. C.; Hunt, B. D.

1989-01-01

Wet chemical techniques are described for treatment of YBa2Cu3O(7-x) surfaces, resulting in the formation of native compounds with little or no reactivity to water. Promising native compounds include CuI, BaSO4, CuS, Cu2S, and the oxalates, all of which are either insoluble or have very low solubility in water. Treatment with dilute HI results in the formation of a native iodide film which is 80-90 percent CuI with small amounts of YI3 and BaI2. Treatment with dilute H2SO4 results in the formation of a film which is 95 percent BaSO4 and 5 percent Y2(SO4)3. Cu2S is formed on the surface with a dilute Na2S solution. An oxalate film with equal amounts of Y2(C2O4)3 and BaC2O4 results from treatment with dilute oxalic acid. X-ray photoelectron spectra show no significant changes when the sulfide, sulfate, or oxalate films are dipped in water, while the iodide film shows evidence of Cu(OH)2 formation.

Synthesis and characterization of beta-Ga2O3 nanorod array clumps by chemical vapor deposition.

PubMed

Shi, Feng; Wei, Xiaofeng

2012-11-01

beta-Ga2O3 nanorod array clumps were successfully synthesized on Si (111) substrates by chemical vapor deposition. The composition, microstructure, morphology, and light-emitting property of these clumps were characterized by X-ray diffraction, Fourier transform infrared spectrophotometry, X-ray photoelectron spectroscopy, scanning electron microscopy, high-resolution transmission electron microscopy, Raman spectroscopy, and photoluminescence. The results demonstrate that the sample synthesized at 1050 degrees C for 15 min was composed of monoclinic beta-Ga2O3 nanorod array clumps, where each single nanorod was about 300 nm in diameter with some nano-droplets on its tip. These results reveal that the growth mechanism agrees with the vapor-liquid-solid (VLS) process. The photoluminescence spectrum shows that the Ga2O3 nanorods have a blue emission at 438 nm, which may be attributed to defects, such as oxygen vacancies and gallium-oxygen vacancy pairs. Defect-energy aggregation confinement growth theory was proposed to explain the growth mechanism of Ga2O3 nanorod array clumps collaborated with the VLS mechanism.

Synthesis of nanoporous CuO/TiO2/Pd-NiO composite catalysts by chemical dealloying and their performance for methanol and ethanol electro-oxidation

NASA Astrophysics Data System (ADS)

Niu, Mengying; Xu, Wence; Zhu, Shengli; Liang, Yanqin; Cui, Zhenduo; Yang, Xianjin; Inoue, Akihisa

2017-09-01

Nanoporous CuO/TiO2/Pd-NiO-x (x = 0, 1, 3, 5, 7 at%) catalysts have been synthesized by dealloying Cu-Ti-Pd-Ni alloy ribbons in acid solution. The nanoporous structure and chemical composition of the catalysts distribute uniformly. Based on the electrochemical active area (EASA), electrocatalytic activity and stability, the np-CuO/TiO2/Pd-NiO-3 catalyst possesses the best performance for methanol and ethanol electro-oxidation. For methanol and ethanol electro-oxidation, the anodic current densities in forward scan of the np-CuO/TiO2/Pd-NiO-3 catalyst are about 5.6 times and 2.1 times larger than that of the np-CuO/TiO2/Pd catalyst, respectively. The introduction of NiO provides more electrochemical active sites due to the improved geometrical and bifunctional mechanism. NiO promotes the adsorption of oxygen-containing species (OHads) on the catalyst surface, and electron effect between Pd and Ni is favorable for charge transfer. This accelerates the removal of intermediate products during the oxidation process. The electrocatalytic processes of methanol and ethanol oxidation in alkaline solution are controlled by both charge transfer and diffusion.

Control of the shape and size of iron oxide (α-Fe2O3) nanoparticles synthesized through the chemical precipitation method

NASA Astrophysics Data System (ADS)

Lassoued, Abdelmajid; Dkhil, Brahim; Gadri, Abdellatif; Ammar, Salah

Hematite (α-Fe2O3) nanoparticles were synthesized via a simple chemical precipitation method. The impact of varying the concentration of precursor on the crystalline phase, size and morphology of α-Fe2O3 products was explored. The characteristic of the synthesized hematite nanoparticles were evaluated by X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Scanning Electron Microscopy (SEM), Fourier Transform Infra-Red (FT-IR) spectroscopy, Raman spectroscopy, Differential Thermal Analysis (DTA), Thermo Gravimetric Analysis (TGA), Ultraviolet-Visible (UV-Vis) analysis and Photoluminescence (PL). XRD data revealed a rhombohedral (hexagonal) structure with the space group R-3c in all samples. Uniform spherical like morphology was confirmed by TEM and SEM. The result revealed that the particle sizes were varied between 21 and 82 nm and that the increase in precursor concentration (FeCl3, 6H2O) is accompanied by an increase in the particle size of 21 nm for pure α-Fe2O3 synthesized with [Fe3+] = 0.05 M at 82 nm for pure α-Fe2O3 synthesized with [Fe3+] = 0.4 M. FT-IR confirms the phase purity of the nanoparticles synthesized. The Raman spectroscopy was used not only to prove that we have synthesized pure hematite but also to identify their phonon modes. The thermal behavior of compound was studied by using TGA/DTA results: The TGA showed three mass losses, whereas DTA resulted in three endothermic peaks. Besides, the optical investigation revealed that samples have an optical gap of about 2.1 eV and that this value varies as a function of the precursor concentration.

Effects of climate change, CO2 and O3 on wheat productivity in Eastern China, singly and in combination

NASA Astrophysics Data System (ADS)

Tao, Fulu; Feng, Zhaozhong; Tang, Haoye; Chen, Yi; Kobayashi, Kazuhiko

2017-03-01

Air pollution and climate change are increasing threats to agricultural production and food security. Extensive studies have focused on the effect of climate change, but the interactive effects of multiple global change factors are poorly understood. Here, we incorporate the interactions between climate change, carbon dioxide (CO2) and ozone (O3) into an eco-physiological mechanistic model based on three years of O3 Free-Air Concentration Elevation (O3-FACE) experiments. We then investigate the effects of climate change, elevated CO2 concentration ([CO2]) and rising O3 concentration ([O3]) on wheat growth and productivity in eastern China in 1996-2005 (2000s) and 2016-2025 (2020s) under two climate change scenarios, singly and in combination. We find the interactive effects of climate change, CO2 and O3 on wheat productivity have spatially explicit patterns; the effect of climate change dominates the general pattern, which is however subject to the large uncertainties of climate change scenarios. Wheat productivity is estimated to increase by 2.8-9.0% due to elevated [CO2] however decline by 2.8-11.7% due to rising [O3] in the 2020s, relative to the 2000s. The combined effects of CO2 and O3 are less than that of O3 only, on average by 4.6-5.2%, however with O3 damage outweighing CO2 benefit in most of the region. This study demonstrates a more biologically meaningful and appropriate approach for assessing the interactive effects of climate change, CO2 and O3 on crop growth and productivity. Our findings promote the understanding on the interactive effects of multiple global change factors across contrasting climate conditions, cast doubt on the potential of CO2 fertilization effect in offsetting possible negative effect of climate change on crop productivity as suggested by many previous studies.

Chemical looping combustion: A new low-dioxin energy conversion technology.

PubMed

Hua, Xiuning; Wang, Wei

2015-06-01

Dioxin production is a worldwide concern because of its persistence and carcinogenic, teratogenic, and mutagenic effects. The pyrolysis-chemical looping combustion process of disposing solid waste is an alternative to traditional solid waste incineration developed to reduce the dioxin production. Based on the equilibrium composition of the Deacon reaction, pyrolysis gas oxidized by seven common oxygen carriers, namely, CuO, NiO, CaSO4, CoO, Fe2O3, Mn3O4, and FeTiO3, is studied and compared with the pyrolysis gas directly combusted by air. The result shows that the activity of the Deacon reaction for oxygen carriers is lower than that for air. For four typical oxygen carriers (CuO, NiO, Fe2O3, and FeTiO3), the influences of temperature, pressure, gas composition, and tar on the Deacon reaction are discussed in detail. According to these simulation results, the dioxin production in China, Europe, the United States, and Japan is predicted for solid waste disposal by the pyrolysis-chemical looping combustion process. Thermodynamic analysis results in this paper show that chemical looping combustion can reduce dioxin production in the disposal of solid waste. Copyright © 2015. Published by Elsevier B.V.

Chloryl nitrate - A novel product of the OClO + NO3 + M recombination

NASA Technical Reports Server (NTRS)

Friedl, Randall R.; Sander, Stanley P.; Yung, Yuk L.

1992-01-01

The products of the reaction of OClO with NO3 were investigated between 220 and 298 K using a flow reactor and infrared, visible, and ultraviolet analysis. At temperatures below 250 K new infrared and ultraviolet absorption features were observed and assigned to the novel compound chloryl nitrate (O2ClONO2). Additionally, ClO and NO2 were observed as reaction products, indicating the existence of a second reaction channel. O2ClONO2 formation predominates at temperatures below 230 K. The reaction rate constant at 220 K is estimated to be on the order of 10 exp -14 cu cm/molecule s in 1-5 Torr of helium. These observations suggest that O2ClONO2 may exist in the terrestrial stratosphere.

Volatile products from the interaction of KCl(g) with Cr2O3 and LaCrO3 in oxidizing environments

NASA Technical Reports Server (NTRS)

Kohl, F. J.; Miller, R. A.; Stearns, C. A.; Fryburg, G. C.; Dillard, J. G.

1977-01-01

Cooled target collection techniques and high pressure mass spectrometric sampling were used to measure the relative rates of oxidative vaporization and to identify the volatile products emanating from samples of chromia and Mg-doped lanthanum chromite. The materials were exposed to partial pressures of KCl with and without H2O in one atmosphere of slowly flowing oxygen at elevated temperatures. Chromia and fresh samples of lanthanum chromite exhibited enhanced rates of oxidative vaporization upon exposure to these reactants. Mass spectrometric identification showed that the enhancements resulted from the heterogeneous formation of complex molecules of the type KCl sub 1,2,3 CrO3 and KOH sub l,2 CrO3. Lanthanum chromite that had undergone prolonged oxidative vaporization exhibited no enhanced oxidation upon exposure to the reactants.

Dynamic exit-channel pathways of the microsolvated HOO-(H2O) + CH3Cl SN2 reaction: Reaction mechanisms at the atomic level from direct chemical dynamics simulations

NASA Astrophysics Data System (ADS)

Yu, Feng

2018-01-01

Microsolvated bimolecular nucleophilic substitution (SN2) reaction of monohydrated hydrogen peroxide anion [HOO-(H2O)] with methyl chloride (CH3Cl) has been investigated with direct chemical dynamics simulations at the M06-2X/6-31+G(d,p) level of theory. Dynamic exit-channel pathways and corresponding reaction mechanisms at the atomic level are revealed in detail. Accordingly, a product distribution of 0.85:0.15 is obtained for Cl-:Cl-(H2O), which is consistent with a previous experiment [D. L. Thomsen et al. J. Am. Chem. Soc. 135, 15508 (2013)]. Compared with the HOO- + CH3Cl SN2 reaction, indirect dynamic reaction mechanisms are enhanced by microsolvation for the HOO-(H2O) + CH3Cl SN2 reaction. On the basis of our simulations, further crossed molecular beam imaging experiments are highly suggested for the SN2 reactions of HOO- + CH3Cl and HOO-(H2O) + CH3Cl.

Dynamic exit-channel pathways of the microsolvated HOO-(H2O) + CH3Cl SN2 reaction: Reaction mechanisms at the atomic level from direct chemical dynamics simulations.

PubMed

Yu, Feng

2018-01-07

Microsolvated bimolecular nucleophilic substitution (S N 2) reaction of monohydrated hydrogen peroxide anion [HOO - (H 2 O)] with methyl chloride (CH 3 Cl) has been investigated with direct chemical dynamics simulations at the M06-2X/6-31+G(d,p) level of theory. Dynamic exit-channel pathways and corresponding reaction mechanisms at the atomic level are revealed in detail. Accordingly, a product distribution of 0.85:0.15 is obtained for Cl - :Cl - (H 2 O), which is consistent with a previous experiment [D. L. Thomsen et al. J. Am. Chem. Soc. 135, 15508 (2013)]. Compared with the HOO - + CH 3 Cl S N 2 reaction, indirect dynamic reaction mechanisms are enhanced by microsolvation for the HOO - (H 2 O) + CH 3 Cl S N 2 reaction. On the basis of our simulations, further crossed molecular beam imaging experiments are highly suggested for the S N 2 reactions of HOO - + CH 3 Cl and HOO - (H 2 O) + CH 3 Cl.

Chemical nature and immunotoxicological properties of arachidonic acid degradation products formed by exposure to ozone

DOE Office of Scientific and Technical Information (OSTI.GOV)

Madden, M.C.; Friedman, M.; Hanley, N.

1993-06-01

Ozone (O3) exposure in vivo has been reported to degrade arachidonic acid (AA) in the lungs of rodents. The O3-degraded AA products may play a role in the responses to this toxicant. To study the chemical nature and biological activity of O3-exposed AA, we exposed AA in a cell-free, aqueous environment to air, 0.1 ppm O3, or 1.0 ppm O3 for 30-120 min. AA exposed to air was not degraded. All O3 exposures degraded > 98% of the AA to more polar products, which were predominantly aldehydic substances (as determined by reactivity with 2,4-dinitrophenylhydrazine and subsequent separation by HPLC) andmore » hydrogen peroxide. The type and amount of aldehydic substances formed depended on the O3 concentration and exposure duration. A human bronchial epithelial cell line (BEAS-2B, S6 subclone) exposed in vitro to either 0.1 ppm or 1.0 ppm O3 for 1 hr produced AA-derived aldehydic substances, some of which eluted with similar retention times as the aldehydic substances derived from O3 degradation of AA in the cell-free system. In vitro, O3-degraded AA induced an increase in human peripheral blood polymorphonuclear leukocyte (PMN) polarization, decreased human peripheral blood T-lymphocyte proliferation in response to mitogens, and decreased human peripheral blood natural killer cell lysis of K562 target cells. The aldehydic substances, but not hydrogen peroxide, appeared to be the principal active agents responsible for the observed effects. O3-degraded AA may play a role in the PMN influx into lungs and in decreased T-lymphocyte mitogenesis and natural killer cell activity observed in humans and rodents exposed to O3.« less

Negative-hydrogen-ion production from a nanoporous 12CaO • 7Al2O3 electride surface

NASA Astrophysics Data System (ADS)

Sasao, Mamiko; Moussaoui, Roba; Kogut, Dmitry; Ellis, James; Cartry, Gilles; Wada, Motoi; Tsumori, Katsuyoshi; Hosono, Hideo

2018-06-01

A high production rate of negative hydrogen ions (H‑) was observed from a nanoporous 12CaO • 7Al2O3 (C12A7) electride surface immersed in hydrogen/deuterium low-pressure plasmas. The target was negatively biased at 20–130 V, and the target surface was bombarded by H3 + ions from the plasma. The production rate was compared with that from a clean molybdenum surface. Using the pseudo-exponential work-function dependence of the H‑ production rate, the total H‑ yield from the C12A7 electride surface bombarded at 80 V was evaluated to be 25% of that from a cesiated molybdenum surface with the lowest work-function. The measured H‑ energy spectrum indicates that the major production mechanism is desorption by sputtering. This material has potential to be used as a production surface of cesium-free negative ion sources for accelerators, heating beams in nuclear fusion, and surface modification for industrial applications.

Photoemission from buried interfaces in SrTiO3/LaTiO3 superlattices.

PubMed

Takizawa, M; Wadati, H; Tanaka, K; Hashimoto, M; Yoshida, T; Fujimori, A; Chikamatsu, A; Kumigashira, H; Oshima, M; Shibuya, K; Mihara, T; Ohnishi, T; Lippmaa, M; Kawasaki, M; Koinuma, H; Okamoto, S; Millis, A J

2006-08-04

We have measured photoemission spectra of SrTiO3/LaTiO3 superlattices with a topmost SrTiO3 layer of variable thickness. A finite coherent spectral weight with a clear Fermi cutoff was observed at chemically abrupt SrTiO3/LaTiO3 interfaces, indicating that an "electronic reconstruction" occurs at the interface between the Mott insulator LaTiO3 and the band insulator SrTiO3. For SrTiO3/LaTiO3 interfaces annealed at high temperatures (approximately 1000 degrees C), which leads to Sr/La atomic interdiffusion and hence to the formation of La(1-x)Sr(x)TiO3-like material, the intensity of the incoherent part was found to be dramatically reduced whereas the coherent part with a sharp Fermi cutoff was enhanced due to the spread of charge. These important experimental features are well reproduced by layer dynamical-mean-field-theory calculation.

Kinetics of the benzyl + O(3P) reaction: a quantum chemical/statistical reaction rate theory study.

PubMed

da Silva, Gabriel; Bozzelli, Joseph W

2012-12-14

The resonance stabilized benzyl radical is an important intermediate in the combustion of aromatic hydrocarbons and in polycyclic aromatic hydrocarbon (PAH) formation in flames. Despite being a free radical, benzyl is relatively stable in thermal, oxidizing environments, and is predominantly removed through bimolecular reactions with open-shell species other than O(2). In this study the reaction of benzyl with ground-state atomic oxygen, O((3)P), is examined using quantum chemistry and statistical reaction rate theory. C(7)H(7)O energy surfaces are generated at the G3SX level, and include several novel pathways. Transition state theory is used to describe elementary reaction kinetics, with canonical variational transition state theory applied for barrierless O atom association with benzyl. Apparent rate constants and branching ratios to different product sets are obtained as a function of temperature and pressure from solving the time-dependent master equation, with RRKM theory for microcanonical k(E). These simulations indicate that the benzyl + O reaction predominantly forms the phenyl radical (C(6)H(5)) plus formaldehyde (HCHO), with lesser quantities of the C(7)H(6)O products benzaldehyde, ortho-quinone methide, and para-quinone methide (+H), along with minor amounts of the formyl radical (HCO) + benzene. Addition of O((3)P) to the methylene site in benzyl produces a highly vibrationally excited C(7)H(7)O* adduct, the benzoxyl radical, which can β-scission to benzaldehyde + H and phenyl + HCHO. In order to account for the experimental observation of benzene as the major reaction product, a roaming radical mechanism is proposed that converts the nascent products phenyl and HCHO to benzene + HCO. Oxygen atom addition at the ortho and para ring sites in benzyl, which has not been previously considered, is shown to lead to the quinone methides + H; these species are less-stable isomers of benzaldehyde that are proposed as important combustion intermediates, but

Biohydrogen production from a novel alkalophilic isolate Clostridium sp. IODB-O3.

PubMed

Patel, Anil Kumar; Debroy, Arundhati; Sharma, Sandeep; Saini, Reetu; Mathur, Anshu; Gupta, Ravi; Tuli, Deepak Kumar

2015-01-01

Hydrogen producing bacteria IODB-O3 was isolated from sludge and identified as Clostridium sp. by 16S rDNA gene analysis. In this study, biohydrogen production process was developed using low-cost agro-waste. Maximum H2 was produced at 37°C and pH 8.5. Maximum H2 yield was obtained 2.54±0.2mol-H2/mol-reducing sugar from wheat straw pre-hydrolysate (WSPH) and 2.61±0.1mol-H2/mol-reducing sugar from pre-treated wheat straw enzymatic-hydrolysate (WSEH). The cumulative H2 production (ml/L), 3680±105 and 3270±100, H2 production rate (ml/L/h), 153±5 and 136±5, and specific H2 production (ml/g/h), 511±5 and 681±10 with WSPH and WSEH were obtained, respectively. Biomass pre-treatment via steam-explosion generates ample amount of WSPH which remains unutilized for bioethanol production due to non-availability of efficient C5-fermenting microorganisms. This study shows that Clostridium sp. IODB-O3 is capable of utilizing WSPH efficiently for biohydrogen production. This would lead to reduced economic constrain on the overall cellulosic ethanol process and also establish a sustainable biohydrogen production process. Copyright © 2014 Elsevier Ltd. All rights reserved.

Observations of VOC Emissions and Photochemical Products over US Oil- and Gas-Producing Regions Using High-Resolution H3O+ CIMS (PTR-ToF-MS)

NASA Technical Reports Server (NTRS)

Koss, Abigail; Yuan, Bin; Warneke, Carsten; Gilman, Jessica B.; Lerner, Brian M.; Veres, Patrick R.; Peischl, Jeff; Eilerman, Scott; Wild, Rob; Brown, Steven S.;

Low-Temperature Process for Atomic Layer Chemical Vapor Deposition of an Al2O3 Passivation Layer for Organic Photovoltaic Cells.

PubMed

Kim, Hoonbae; Lee, Jihye; Sohn, Sunyoung; Jung, Donggeun

2016-05-01

Flexible organic photovoltaic (OPV) cells have drawn extensive attention due to their light weight, cost efficiency, portability, and so on. However, OPV cells degrade quickly due to organic damage by water vapor or oxygen penetration when the devices are driven in the atmosphere without a passivation layer. In order to prevent damage due to water vapor or oxygen permeation into the devices, passivation layers have been introduced through methods such as sputtering, plasma enhanced chemical vapor deposition, and atomic layer chemical vapor deposition (ALCVD). In this work, the structural and chemical properties of Al2O3 films, deposited via ALCVD at relatively low temperatures of 109 degrees C, 200 degrees C, and 300 degrees C, are analyzed. In our experiment, trimethylaluminum (TMA) and H2O were used as precursors for Al2O3 film deposition via ALCVD. All of the Al2O3 films showed very smooth, featureless surfaces without notable defects. However, we found that the plastic flexible substrate of an OPV device passivated with 300 degrees C deposition temperature was partially bended and melted, indicating that passivation layers for OPV cells on plastic flexible substrates need to be formed at temperatures lower than 300 degrees C. The OPV cells on plastic flexible substrates were passivated by the Al2O3 film deposited at the temperature of 109 degrees C. Thereafter, the photovoltaic properties of passivated OPV cells were investigated as a function of exposure time under the atmosphere.

Material properties of perovskites in the quasi-ternary system LaFeO 3–LaCoO 3–LaNiO 3

DOE PAGES

Tietz, F.; Arul Raj, I.; Ma, Q.; ...

2016-02-02

We present an overview on the variation of electrical conductivity, oxygen permeation, oxygen surface exchange and thermal expansion coefficient as a function of the composition of perovskites in the quasi-ternary system LaFeO 3–LaCoO 3–LaNiO 3. Powders of thirteen nominal perovskite compositions were synthesized under identical conditions by the Pechini method. The powder X-ray diffraction data of two series, namely La(Ni 0.5Fe 0.5) 1-xCo xO 3 and LaNi 0.5- xFe xCo 0.5O 3, are presented after the powders had been sintered at 1100 C for 6 h in air. The measurements revealed a rhombohedral structure for all compositions except LaNi 0.5Femore » 0.5O 3 for which 60% rhombohedral and 40% orthorhombic phase was found. Moreover, the maximum DC electrical conductivity value of the perovskites at 800 C was 1229 S cm-1 for the composition LaCoO 3 and the minimum was 91 S cm-1 for the composition LaCo 0.5Fe 0.5O 3. The oxygen permeation of samples with promising conductivities at 800 C was one order of magnitude lower than that of La 0.6Sr 0.4Co 0.8Fe 0.2O 3 (LSCF). The highest value of 0.017 ml cm -2 min-1 at 950 C was obtained with LaNi 0.5Co 0.5O 3. The coefficients of thermal expansion varied in the range of 13.2 x 10 -6 K -1 and 21.9 x 10 -6 K -1 for LaNi 0.5Fe 0.5O 3 and LaCoO 3, respectively. 57Fe M ssbauer spectroscopy was used as probe for the oxidation states, local environment and magnetic properties of iron ions as a function of chemical composition. Ultimately, the substitution had a great influence on the chemical properties of the materials.« less

Synthesis of nano-sized crystalline oxide ion conducting fluorite-type Y 2O 3-doped CeO 2 using perovskite-like BaCe 0.9Y 0.1O 2.95 (BCY) and study of CO 2 capture properties of BCY

NASA Astrophysics Data System (ADS)

Sneha, B. R.; Thangadurai, V.

2007-10-01

Formation of nano-sized Y 2O 3-doped CeO 2 (YCO) was observed in the chemical reaction between proton conducting Y 2O 3-doped BaCeO 3 (BCY) and CO 2 in the temperature range 700-1000 °C, which is generally prepared by wet-chemical methods that include sol-gel, hydrothermal, polymerization, combustion, and precipitation reactions. BCY can capture CO 2 of 0.13 g per ceramic gram at 700 °C, which is comparable to that of the well-known Li 2ZrO 3 (0.15 g per ceramic gram at 600 °C). Powder X-ray diffraction (PXRD), energy dispersive X-ray analysis (EDX), laser particle size analysis (LPSA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and ac impedance spectroscopy were employed to characterize the reaction product obtained from reaction between BCY and CO 2 and subsequent acid washing. PXRD study reveals presence of fluorite-like CeO 2 ( a=5.410 (1) Å) structure and BaCO 3 in reaction products. TEM investigation of the acid washed product showed the formation of nano-sized material with particle sizes of about 50 nm. The electrical conductivity of acid washed product (YCO) in air was found to be about an order higher than the undoped CeO 2 reported in the literature.

[Preventive measures against health damage due to chemicals in household products].

PubMed

Kaniwa, Masa-aki

2010-01-01

Chemicals in household products have been paid much attention as the main cause of health damage in consumers, such as allergic contact dermatitis. Preventive measures against health damage due to chemicals in fabrics, plastics and rubber products for household use, are reviewed, focusing on 1) the incidence of health damage due to household products, 2) causative product-chemical investigation, and 3) case studies on skin damage.

Synthesis of Bifunctional Fe3O4@SiO2-Ag Magnetic-Plasmonic Nanoparticles by an Ultrasound Assisted Chemical Method

NASA Astrophysics Data System (ADS)

Chu, Dung Tien; Sai, Doanh Cong; Luu, Quynh Manh; Tran, Hong Thi; Quach, Truong Duy; Kim, Dong Hyun; Nguyen, Nam Hoang

2017-06-01

Bifunctional magnetic-plasmonic nanoparticles (NPs)—Fe3O4@SiO2-Ag were successfully synthesized by an ultrasound assisted chemical method. Silver ions were absorbed and then reduced by sodium borohydride on the surface of 3-aminopropyltriethoxysilane (APTES) functionalized silica-coated magnetic NPs, then they were reduced under the influence of a 200 W ultrasonic wave for 60 min. When the amount of precursor silver ions increased, the relative intensity of diffraction peaks of silver crystals in all samples increased with the atomic ratio of silver/iron increasing from 0.208 to 0.455 and saturation magnetization ( M s) decreasing from 44.68 emu/g to 34.74 emu/g. The NPs have superparamagnetic properties and strong surface plasmon absorption at 420 nm, which make these particles promising for biomedical applications.

Ozone air quality simulations with WRF-Chem (v3.5.1) over Europe: model evaluation and chemical mechanism comparison

NASA Astrophysics Data System (ADS)

Mar, Kathleen A.; Ojha, Narendra; Pozzer, Andrea; Butler, Tim M.

2016-10-01

We present an evaluation of the online regional model WRF-Chem over Europe with a focus on ground-level ozone (O3) and nitrogen oxides (NOx). The model performance is evaluated for two chemical mechanisms, MOZART-4 and RADM2, for year-long simulations. Model-predicted surface meteorological variables (e.g., temperature, wind speed and direction) compared well overall with surface-based observations, consistent with other WRF studies. WRF-Chem simulations employing MOZART-4 as well as RADM2 chemistry were found to reproduce the observed spatial variability in surface ozone over Europe. However, the absolute O3 concentrations predicted by the two chemical mechanisms were found to be quite different, with MOZART-4 predicting O3 concentrations up to 20 µg m-3 greater than RADM2 in summer. Compared to observations, MOZART-4 chemistry overpredicted O3 concentrations for most of Europe in the summer and fall, with a summertime domain-wide mean bias of +10 µg m-3 against observations from the AirBase network. In contrast, RADM2 chemistry generally led to an underestimation of O3 over the European domain in all seasons. We found that the use of the MOZART-4 mechanism, evaluated here for the first time for a European domain, led to lower absolute biases than RADM2 when compared to ground-based observations. The two mechanisms show relatively similar behavior for NOx, with both MOZART-4 and RADM2 resulting in a slight underestimation of NOx compared to surface observations. Further investigation of the differences between the two mechanisms revealed that the net midday photochemical production rate of O3 in summer is higher for MOZART-4 than for RADM2 for most of the domain. The largest differences in O3 production can be seen over Germany, where net O3 production in MOZART-4 is seen to be higher than in RADM2 by 1.8 ppb h-1 (3.6 µg m-3 h-1) or more. We also show that while the two mechanisms exhibit similar NOx sensitivity, RADM2 is

Chemical evaluation of HBED/Fe(3+) and the novel HJB/Fe(3+) chelates as fertilizers to alleviate iron chlorosis.

PubMed

López-Rayo, Sandra; Hernández, Diana; Lucena, Juan J

2009-09-23

Iron chelates such as ethylenediamine-N,N'-bis(2-hydroxyphenylacetic) acid (o,o-EDDHA) and their analogues are the most efficient soil fertilizers to treat iron chlorosis in plants growing in calcareous soil. A new chelating agent, HJB (N,N'-bis(2-hydroxy-5-methylphenyl)ethylendiamine-N,N'-diacetic acid) may be an alternative to o,o-EDDHA since its synthesis yields a purer product, but its chemical behavior and efficiency as chlorosis corrector should be evaluated. In this research, a known analogous HBED (N,N'-bis(2-hydroxyphenyl)ethylendiamine-N,N'-diacetic acid) has also been considered. First, an ion-pair high performance liquid chromatography (HPLC) method has been tested for the HJB/Fe(3+) and HBED/Fe(3+) determination. The ability of HJB and HBED to maintain Fe in solution has been compared with respect to o,o-EDDHA. Theoretical modelization for HBED and HJB in agronomic conditions has been done after the determination of the protonation and Ca(II), Mg(II), Fe(III), and Cu(II) stability constants for HJB. Also, batch interaction experiments with soils and soil materials have been conducted. According to our results, HJB/Fe(3+) and HBED/Fe(3+) present high stability, even when competing cations (Cu(2+), Ca(2+)) are present, and have low reactivity with soils and soil components. The chelating agent HJB dissolves a higher amount of Fe than o,o-EDDHA, and it seems as effective as o,o-EDDHA in keeping Fe in solution. These results indicate that these chelates may be very efficient products to correct Fe chlorosis, and additional plant experiments should demonstrate plants' ability to assimilate Fe from HJB/Fe(3+) and HBED/Fe(3+).

Energy transfer mechanism of Sm3+/Eu3+ co-doped 2CaO-B2O3-P2O5 phosphors

NASA Astrophysics Data System (ADS)

Prasad, V. Reddy; Damodaraiah, S.; Ratnakaram, Y. C.

2018-04-01

Sm3+/Eu3+ co-doped calcium borophosphate phosphors were synthesized by solid state reaction method. 2CaO-B2O3-P2O5: Sm3+/Eu3+ co-doped phosphors were characterized by XRD, SEM, 31P solid state NMR, excitation, photoluminescence (PL) and decay profiles.. XRD profiles showed that the prepared phosphors exhibit a hexagonal phase in crystal structure and SEM results showed that the particles are more irregular morphologies. From 31P NMR spectra of Sm3+/Eu3+ co-doped 2CaO-B2O3-P2O5 phosphors, the chemical shifts located in the positive frequency region indicating the presence of mono-phosphate complexes Q0-(PO43 - ) . Photoluminescence spectra of Sm3+/Eu3+ co-doped 2CaO-B2O3-P2O5 phosphors show enhancement in emission intensity of Eu3+ ion due to co-doping with Sm3+ ions through energy transfer process. The energy level mechanism between Sm3+ and Eu3+ ions has been clearly explained. The energy transfer process has also been evidenced by lifetime decay profiles. These results suggest that the prepared phosphors are potential red luminescent optical materials.

Photogenerated Hole-Induced Chemical Redox Cycling on Bi2S3/Bi2Sn2O7 Heterojunction: Toward General Amplified Split-Type Photoelectrochemical Immunoassay.

PubMed

Cao, Jun-Tao; Wang, Bing; Dong, Yu-Xiang; Wang, Qian; Ren, Shu-Wei; Liu, Yan-Ming; Zhao, Wei-Wei

2018-06-04

This work reports the elegant bridging of enzymatic generation of electron donor with photogenerated hole-induced chemical redox cycling amplification (RCA) for innovative photoelectrochemical (PEC) immunoassay, by the aid of a heterojunction photoelectrode with split-type strategy. Specifically, the system was exemplified by the alkaline phosphatase (ALP) catalytic generation of ascorbic acid (AA), the redox cycling of AA by tris (2-carboxyethyl) phosphine (TCEP) as reductant, and the use of a novel Bi 2 S 3 /Bi 2 Sn 2 O 7 heterojunction and myoglobin (Myo) as the photoelectrode and the target, respectively. After the immunoreaction and ALP-induced production of AA, the subsequent oxidation of AA by the photogenerated holes of the Bi 2 S 3 /Bi 2 Sn 2 O 7 heterojunction could be cycled via the regeneration of AA by TCEP from the oxidized product of dehydroascorbic acid, leading to easy signal amplification for the sensitive immunoassay of Myo in real samples. It is believed that this work provided a basis for further design and development of general RCA-based PEC immunoassays.

CH 3NO 2 decomposition/isomerization mechanism and product branching ratios: An ab initio chemical kinetic study

NASA Astrophysics Data System (ADS)

Zhu, R. S.; Lin, M. C.

2009-08-01

The low-lying energy pathways for the decomposition/isomerization of nitromethane (NM) have been investigated using different molecular orbital methods. Our results show that in addition to the commonly known CH 3 + NO 2 products formed by direct C-N bond breaking and the trans-CH 3ONO formed by nitro-nitrite isomerization, NM can also isomerize to cis-CH 3ONO via a very loose transition state (TS) lying 59.2 kcal/mol above CH 3NO 2 or 0.6 kcal/mol below the CH 3 + NO 2 asymptote predicted at the UCCSD(T)/CBS level of theory. Kinetic results indicate that in the energy range of 59 ± 1 kcal/mol, production of CH 3O + NO is dominant, whereas above the C-N bond breaking threshold, the formation of CH 3 + NO 2 sharply increases and becomes dominant. The k( E) values predicted at different energies clearly indicate that CH 3O + NO could be detected in an infrared multi-photon dissociation study, whereas in UV dissociation experiments with energies high above the C-N bond breaking threshold the CH 3 + NO 2 products are generated predominantly.

Imprint control of BaTiO 3 thin films via chemically induced surface polarization pinning

DOE PAGES

Lee, Hyungwoo; Kim, Tae Heon; Patzner, Jacob J.; ...

2016-02-22

Surface-adsorbed polar molecules can significantly alter the ferroelectric properties of oxide thin films. Thus, fundamental understanding and controlling the effect of surface adsorbates are crucial for the implementation of ferroelectric thin film devices, such as ferroelectric tunnel junctions. Herein, we report an imprint control of BaTiO 3 (BTO) thin films by chemically induced surface polarization pinning in the top few atomic layers of the water-exposed BTO films. Our studies based on synchrotron X-ray scattering and coherent Bragg rod analysis demonstrate that the chemically induced surface polarization is not switchable but reduces the polarization imprint and improves the bistability of ferroelectricmore » phase in BTO tunnel junctions. Here, we conclude that the chemical treatment of ferroelectric thin films with polar molecules may serve as a simple yet powerful strategy to enhance functional properties of ferroelectric tunnel junctions for their practical applications.« less

Modeling C1-C4 Alkyl Nitrate Photochemistry and Their Impacts on O3 Production in Urban and Suburban Environments of Hong Kong

NASA Astrophysics Data System (ADS)

Lyu, X. P.; Guo, H.; Wang, N.; Simpson, I. J.; Cheng, H. R.; Zeng, L. W.; Saunders, S. M.; Lam, S. H. M.; Meinardi, S.; Blake, D. R.

2017-10-01

As intermediate products of photochemical reactions, alkyl nitrates (RONO2) regulate ozone (O3) formation. In this study, a photochemical box model incorporating master chemical mechanism well reproduced the observed RONO2 at an urban and a mountainous site, with index of agreement in the range of 0.66-0.73. The value 0.0003 was identified to be the most appropriate branching ratio for C1 RONO2, with the error less than 50%. Although levels of the parent hydrocarbons and nitric oxide (NO) were significantly higher at the urban site than the mountainous site, the production of C2-C3 RONO2 was comparable to or even lower than at the mountainous site, due to the lower concentrations of oxidative radicals in the urban environment. Based on the profiles of air pollutants at the mountainous site, the formation of C2-C4 RONO2 was limited by NOx (volatile organic compounds (VOCs)) when total volatile organic compounds (TVOCs)/NOx was higher (lower) than 10.0 ± 0.4 parts per billion by volume (ppbv)/ppbv. This dividing ratio decreased (p < 0.05) to 8.7 ± 0.4 ppbv/ppbv at the urban site, mainly due to the different air pollutant profiles at the two sites. For the formation of C1 RONO2, the NOx-limited regime extended the ratio of TVOCs/NOx to as low as 2.4 ± 0.2 and 3.1 ± 0.1 ppbv/ppbv at the mountainous and urban site, respectively. RONO2 formation led to a decrease of simulated O3, with reduction efficiencies (O3 reduction/RONO2 production) of 4-5 parts per trillion by volume (pptv)/pptv at the mountainous site and 3-4 pptv/pptv at the urban site. On the other hand, the variations of simulated O3 induced by RONO2 degradation depended upon the regimes controlling O3 formation and the relative abundances of TVOCs and NOx.

[Preventive measures against health damage due to chemicals in household products].

PubMed

Kaniwa, Masa-aki

2006-01-01

Chemicals in household products have been paid much attention as main cause of health damage on consumers, such as allergic contact dermatitis. Preventive measures against health damage due to chemicals in fabric, plastic and rubber products for household uses, are reviewed, focusing on (1) regulation and voluntary control by manufacturers, (2) incidence of health damage from household products, (3) causative product-chemical investigation, (4) case studies on skin damage and respiratory tract damage.

Simultaneous assimilation of satellite NO2, O3, CO, and HNO3 data for the analysis of the tropospheric chemical composition

NASA Astrophysics Data System (ADS)

Miyazaki, K.; Eskes, H.; Sudo, K.

2012-04-01

Carbon monoxide (CO) and nitrogen oxides (NOx) play an important role in tropospheric chemistry through their influences on the ozone and hydroxyl radical (OH). The simultaneous optimization of various chemical components is expected to improve the emission inversion through the better description of the chemical feedbacks in the NOx- and CO-chemistry. This study aims to reproduce chemical composition distributions in the troposphere by combining information obtained from multiple satellite data sets. The emissions of CO and NOx, together with the 3D concentration fields of all forecasted chemical species in the global CTM CHASER have been simultaneously optimized using the ensemble Kalman filter (EnKF) data assimilation technique, and NO2, O3, CO, and HNO3 data obtained from OMI, TES, MOPITT, and MLS satellite measurements. The performance is evaluated against independent data from ozone sondes, aircraft measurements, GOME-2, and SCIAMACHY satellite data. Observing System Experiments (OSEs) have been carried out. These OSEs quantify the relative importance of each data set on constraining the emissions and concentrations. We confirmed that the simultaneous data assimilation improved the agreement with these independent data sets. The combined analysis of multiple data sets by means of advanced data assimilation system can provide a useful framework for the air quality research.

Synthesis and characterization of nanocrystalline LaMnO3 modified BaTiO3 ferroelectric ceramics prepared by chemical route

NASA Astrophysics Data System (ADS)

Dhak, Prasanta; Adak, Mrinal Kanti; Dhak, Debasis

2016-02-01

Nanocrystalline Ba1-3xTi1-3xLa2xMn4xO3, [x = 0.006, 0.008, 0.01 and 0.05] (abbreviated hereafter as BTLM) by chemical route. The phase formation and purity were checked by X-ray diffraction (XRD) study and transmission electron microscopy (TEM). The grain morphology after sintering was studied by scanning electron microscopy (SEM). The crystallite sizes range from 21 nm to 30 nm, while the particle size ranges between 27 nm and 38 nm. The grain size 212 nm and grain density 96.8% were found to be maximum for BTLM x = 0.05 and x = 0.01, respectively. The temperature dependence of dielectric constants was found to be more diffused and the peak value of the dielectric constant was decreased and more flat with the increase of the substituent concentration. The tangent loss was found to be decreased and reached to the minimum value of 0.032 for BTLM x = 0.05. The remnant polarization Pr, was 10 μC/cm2 for BTLM x = 0.01.

Thermochemistry and kinetics for 2-butanone-1-yl radical (CH2·C(═O)CH2CH3) reactions with O2.

PubMed

Sebbar, N; Bozzelli, J W; Bockhorn, H

2014-01-09

Thermochemistry of reactants, intermediates, transition state structures, and products along with kinetics on the association of CH2·C(═O)CH2CH3 (2-butanone-1-yl) with O2 and dissociation of the peroxy adduct isomers are studied. Thermochemical properties are determined using ab initio (G3MP2B3 and G3) composite methods along with density functional theory (B3LYP/6-311g(d,p)). Entropy and heat capacity contributions versus temperature are determined from structures, vibration frequencies, and internal rotor potentials. The CH2·C(═O)CH2CH3 radical + O2 association results in a chemically activated peroxy radical with 27 kcal mol(-1) excess of energy. The chemically activated adduct can react to stabilized peroxy or hydroperoxide alkyl radical adducts, further react to lactones plus hydroxyl radical, or form olefinic ketones and a hydroperoxy radical. Kinetic parameters are determined from the G3 composite methods derived thermochemical parameters, and quantum Rice-Ramsperger-Kassel (QRRK) analysis to calculate k(E) with master equation analysis to evaluate falloff in the chemically activated and dissociation reactions. One new, not previously reported, peroxy chemistry reaction is presented. It has a low barrier path and involves a concerted reaction resulting in olefin formation, H2O elimination, and an alkoxy radical.

Cyanobacterial chemical production.

PubMed

Case, Anna E; Atsumi, Shota

2016-08-10

The increase in global temperatures caused by rising CO2 levels necessitates the development of alternative sources of fuel and chemicals. One appealing alternative that has been receiving increased attention in recent years is the photosynthetic conversion of atmospheric CO2 to biofuels and chemical products using genetically engineered cyanobacteria. This can help to not only provide an alternate "greener" source for some of the most popular petroleum based products but it can also help to reduce atmospheric CO2. Utilizing cyanobacteria rather than plants allows for reduced land requirements and reduces competition with food crops. This review discusses advancements in the field since 2012 with a particular emphasis on production of hydrocarbons. Copyright © 2016 Elsevier B.V. All rights reserved.

Polycrystalline and Mesoporous 3-D Bi2O3 Nanostructured Negatrodes for High-Energy and Power-Asymmetric Supercapacitors: Superfast Room-Temperature Direct Wet Chemical Growth.

PubMed

Shinde, Nanasaheb M; Xia, Qi Xun; Yun, Je Moon; Mane, Rajaram S; Kim, Kwang Ho

2018-04-04

Superfast (≤10 min) room-temperature (300 K) chemical synthesis of three-dimensional (3-D) polycrystalline and mesoporous bismuth(III) oxide (Bi 2 O 3 ) nanostructured negatrode (as an abbreviation of negative electrode) materials, viz., coconut shell, marigold, honey nest cross section and rose with different surface areas, charge transfer resistances, and electrochemical performances essential for energy storage, harvesting, and even catalysis devices, are directly grown onto Ni foam without and with poly(ethylene glycol), ethylene glycol, and ammonium fluoride surfactants, respectively. Smaller diffusion lengths, caused by the involvement of irregular crevices, allow electrolyte ions to infiltrate deeply, increasing the utility of inner active sites for the following electrochemical performance. A marigold 3-D Bi 2 O 3 electrode of 58 m 2 ·g -1 surface area has demonstrated a specific capacitance of 447 F·g -1 at 2 A·g -1 and chemical stability of 85% even after 5000 redox cycles at 10 A·g -1 in a 6 M KOH electrolyte solution, which were higher than those of other morphology negatrode materials. An asymmetric supercapacitor (AS) device assembled with marigold Bi 2 O 3 negatrode and manganese(II) carbonate quantum dots/nickel hydrogen-manganese(II)-carbonate (MnCO 3 QDs/NiH-Mn-CO 3 ) positrode corroborates as high as 51 Wh·kg -1 energy at 1500 W·kg -1 power and nearly 81% cycling stability even after 5000 cycles. The obtained results were comparable or superior to the values reported previously for other Bi 2 O 3 morphologies. This AS assembly glowed a red-light-emitting diode for 20 min, demonstrating the scientific and industrial credentials of the developed superfast Bi 2 O 3 nanostructured negatrodes in assembling various energy storage devices.

Chemical durability of high-temperature superconductor YBa2Cu3O(7-x) in aqueous environments

NASA Technical Reports Server (NTRS)

Bansal, Narottam P.; Sandkuhl, Ann L.

1988-01-01

The stability of YBa2Cu3O(7-x) in water and 100-percent humidity has been investigated at three temperatures, using pH measurements, X-ray diffraction, and scanning electron microscopy. The oxide-ceramic superconductor is highly unstable; it reacts rapidly with water and degrades in moisture. Dissolution of the oxide perovskite in water is highly incongruent. The corrosion products are found to be BaCO3, CuO, O2, etc. Barium hydroxide is first formed and further reacts with atmospheric CO2 to form needle-shaped crystals of BaCO3. For any practical applications, devices made from these materials would have to be protected with an impermeable coating to prevent deterioration from atmosphere.

Photochemical production of O3 in biomass burning plumes in the boundary layer over northern Australia

NASA Astrophysics Data System (ADS)

Takegawa, N.; Kondo, Y.; Ko, M.; Koike, M.; Kita, K.; Blake, D. R.; Hu, W.; Scott, C.; Kawakami, S.; Miyazaki, Y.; Russell-Smith, J.; Ogawa, T.

2003-05-01

In situ aircraft measurements of ozone (O3) and its precursors were made over northern Australia in August-September 1999 during the Biomass Burning and Lightning Experiment Phase B (BIBLE-B). A clear positive correlation of O3 with carbon monoxide (CO) was found in biomass burning plumes in the boundary layer (<3 km). The ΔO3/ΔCO ratio (linear regression slope of O3-CO correlation) is found to be 0.12 ppbv/ppbv, which is comparable to the ratio of 0.15 ppbv/ppbv observed at 0-4 km over the Amazon and Africa in previous studies. The net flux of O3 exported from northern Australia during BIBLE-B is estimated to be 0.3 Gmol O3/day. In the biomass burning region, large enhancements of O3 were coincident with the locations of biomass burning hot spots, suggesting that major O3 production occurred near fires (horizontal scale <50 km).

Oxygen storage properties of La 1-xSr xFeO 3-δ for chemical-looping reactions–An in-situ neutron and synchrotron X-ray study

DOE PAGES

Taylor, Daniel D.; Schreiber, Nathaniel J.; Levitas, Benjamin D.; ...

2016-05-16

Oxygen storage materials (OSMs) provide lattice oxygen for a number of chemical-looping reactions including natural gas combustion and methane reforming. La 1–xSr xFeO 3-δ has shown promise for use as an OSM in methane reforming reactions due to its high product selectivity, fast oxide diffusion, and cycle stability. Here, we investigate the structural evolution of the series La 1–xSr xFeO 3-δ for x = 0, 1/3, 1/2, 2/3, and 1, using in situ synchrotron X-ray and neutron diffraction, as it is cycled under the conditions of a chemical-looping reactor (methane and oxygen atmospheres). In the compositions x = 1/3, 1/2,more » 2/3, and 1, we discover an envelope , or temperature range, of oxygen storage capacity (OSC), where oxygen can easily and reversibly be inserted and removed from the OSM. Our in situ X-ray and neutron diffraction results reveal that while samples with higher Sr contents had a higher OSC, those same samples suffered from slower reaction kinetics and some, such as the x = 1/2 and x = 2/3 compositions, had local variations in Sr content, which led to inhomogeneous regions with varying reaction rates. Therefore, we highlight the importance of in situ diffraction studies, and we propose that these measurements are required for the thorough evaluation of future candidate OSMs. Furthermore, we recommend La 2/3Sr 1/3FeO 3-δ as the optimal OSM in the series because its structure remains homogeneous throughout the reaction, and its OSC envelope is similar to that of the higher doped materials.« less

Current-voltage characteristics and electroresistance in LaMnO3-δ/La0.7Ca0.3MnO3/LaAlO3 thin film composites.

PubMed

Gadani, Keval; Keshvani, M J; Rajyaguru, Bhargav; Dhruv, Davit; Kataria, B R; Joshi, A D; Asokan, K; Shah, N A; Solanki, P S

2017-11-08

In this communication, we report results of the electrical transport properties across the interface of composites consisting of n-type LaMnO 3-δ (LMO) and p-type La 0.7 Ca 0.3 MnO 3 (LCMO) manganites grown on LaAlO 3 (LAO) single crystalline substrates using low cost wet chemical solution deposition (CSD) and sophisticated, well-controlled dry chemical vapor deposition (CVD) chemical techniques. The XRD ϕ-scan studies reveal the single crystalline nature of both bilayered composites, with parallel epitaxial growth of LMO and LCMO layers onto the LAO substrate. The valence states of Mn ions in both layers of both composites were identified by performing X-ray photoelectron spectroscopy (XPS). The I-V characteristics of the LMO/LCMO interfaces show strong backward diode-like behavior at higher applied voltages well above the crossover voltage (V NB ). Below V NB , the interfaces demonstrate normal diode-like characteristics throughout the studied temperature range. The electric field-induced modulation of the LMO/LCMO junction resistance of the interfaces has been observed. Electric field-dependent electroresistance (ER) modifications at different temperatures have also been studied. The electrical transport properties have been discussed in the context of various mechanisms, such as charge injection, tunneling, depletion region modification and thermal processes across the interface. The effects of structurally and chemically developed sharp interfaces between the LMO and LCMO layers on the transport properties of the presently studied bilayered thin film composites have been discussed on the basis of correlation between the physicochemical characterization and charge transport behavior. A comparison of different aspects of the transport properties has been presented in the context of the structural strain and crystallinity of the composites grown using both wet and dry chemical techniques.

Reversible control of magnetism in La 0.67Sr 0.33MnO 3 through chemically-induced oxygen migration

DOE PAGES

Grutter, A. J.; Gilbert, D. A.; Alaan, U. S.; ...

2016-02-22

We demonstrate reversible control of magnetization and anisotropy in La 0.67Sr 0.33MnO 3 films through interfacial oxygen migration. Gd metal capping layers deposited onto La 0.67Sr 0.33MnO 3 leach oxygen from the film through a solid-state redox reaction to form porous Gd 2O 3. X-ray absorption and polarized neutron reflectometry measurements show Mn valence alterations consistent with high oxygen vacancy concentrations, resulting in suppressed magnetization and increased coercive fields. Effects of the oxygen migration are observed both at the interface and also throughout the majority of a 40 nm thick film, suggesting extensive diffusion of oxygen vacancies. After Gd-capped Lamore » 0.67Sr 0.33MnO 3 is exposed to atmospheric oxygen for a prolonged period of time, oxygen diffuses through the Gd 2O 3 layer and the magnetization of the La 0.67Sr 0.33MnO 3 returns to the uncapped value. In conclusion, these findings showcase perovskite heterostructures as ideal candidates for developing functional interfaces through chemically-induced oxygen migration.« less

Continuous chemical operations and modifications on magnetic γ-Fe2O3 nanoparticles confined in nanoliter droplets for the assembly of fluorescent and magnetic SiO2@γ-Fe2O3.

PubMed

Ferraro, D; Lin, Y; Teste, B; Talbot, D; Malaquin, L; Descroix, S; Abou-Hassan, A

2015-12-11

We present a microfluidic platform that allows undergoing different chemical operations in a nanoliter droplet starting from the colloidal suspension of magnetic iron oxide (γ-Fe2O3) nanoparticles "NPs" (ferrofluid). These operations include: mixing, flocculation, magnetic decantation, colloidal redispersion, washing, surface functionalization, heating and colloidal assembly. To prove the platform capabilities, we produced fluorescent and magnetic nanoassemblies composed of fluorescent silica and magnetic NPs.

Quenching of I(2P1/2) by O3 and O(3P).

PubMed

Azyazov, Valeriy N; Antonov, Ivan O; Heaven, Michael C

2007-04-26

Oxygen-iodine lasers that utilize electrical or microwave discharges to produce singlet oxygen are currently being developed. The discharge generators differ from conventional chemical singlet oxygen generators in that they produce significant amounts of atomic oxygen. Post-discharge chemistry includes channels that lead to the formation of ozone. Consequently, removal of I(2P1/2) by O atoms and O3 may impact the efficiency of discharge driven iodine lasers. In the present study, we have measured the rate constants for quenching of I(2P1/2) by O(3P) atoms and O3 using pulsed laser photolysis techniques. The rate constant for quenching by O3, (1.8 +/- 0.4) x 10(-12) cm3 s-1, was found to be a factor of 5 smaller than the literature value. The rate constant for quenching by O(3P) was (1.2 +/- 0.2) x 10(-11) cm3 s-1.

Chemical thermodynamic representation of (U, Pu, Am)O 2- x

NASA Astrophysics Data System (ADS)

Osaka, Masahiko; Namekawa, Takashi; Kurosaki, Ken; Yamanaka, Shinsuke

2005-09-01

The oxygen potential isotherms of (U, Pu, Am)O 2- x were represented by a chemical thermodynamic model proposed by Lindemer et al. It was assumed in the present model that (U, Pu, Am)O 2- x consisted of the chemical species [UO 2], [PuO 2], [Pu 4/3O 2], [AmO 2] and [Am 5/4O 2] in a pseudo-quaternary system by treating the reduction rates of Pu and Am as identical; furthermore an interaction between [Am 5/4O 2] and [UO 2] was introduced. The agreement between analytical and experimental isotherms was good, but the analytical values slightly overestimated the experimental values especially in the case of lower Am content. Adding an interaction between [Am 5/4O 2] and [PuO 2] to the model resulted in a better representation.

Hydrogen Radicals, Nitrogen Radicals, and the Production of O3 in the Upper Troposphere

NASA Technical Reports Server (NTRS)

Wennberg, P. O.; Hanisco, T. F.; Jaegle, L.; Jacob, D. J.; Hintsa, E. J.; Lanzendorf, E. J.; Anderson, J. G.; Gao, R.-S.; Keim, E. R.; Donnelly, S. G.;

Chemical solution-deposited PbZr 0.53 Ti 0.47 O3 on La 0.5 Sr 0.5 Co O3. SIMS investigation of the effect of different precursor additives on the layer structure.

PubMed

Pollak, C; Malic, B; Kosec, M; Javoric, S; Hutter, H

2002-10-01

Chemical solution-deposited thin films of PbZr(0.53)Ti(0.47)O(3)/La(0.5)Sr(0.5)CoO(3) on Pt/TiO(2)/SiO(2)/Si substrates have been investigated by dynamic SIMS. The PbZr(0.53)Ti(0.47)O(3) (PZT) is intended to serve as a ferroelectric layer for microelectronic or microelectromechanical applications; conducting La(0.5)Sr(0.5)CoO(3) (LSCO) is a buffer layer intended to eliminate fatigue effects which usually occur at the Pt/PZT interface. Depth profiles of the main components were obtained and revealed that significant diffusion occurred during the deposition and crystallisation processes. Two types of sample, with different thickness of PZT and different types of poly(vinyl alcohol) (PVA) added to the LSCO precursor, were investigated.

Catalytic performance of V2O5-MoO3/γ-Al2O3 catalysts for partial oxidation of n-hexane1

NASA Astrophysics Data System (ADS)

Mahmoudian, R.; Khodadadi, Z.; Mahdavi, Vahid; Salehi, Mohammed

2016-01-01

In the current study, a series of V2O5-MoO3 catalyst supported on γ-Al2O3 with various V2O5 and MoO3 loadings was prepared by wet impregnation technique. The characterization of prepared catalysts includes BET surface area, powder X-ray diffraction (XRD), and oxygen chemisorptions. The partial oxidation of n-hexane by air over V2O5-MoO3/γ-Al2O3 catalysts was carried out under flow condition in a fixed bed glass reactor. The effect of V2O5 loading, temperature, MoO3 loading, and n-hexane LHSV on the n-hexane conversion and the product selectivity were investigated. The partial oxygenated products of n-hexane oxidation were ethanol, acetic anhydride, acetic acid, and acetaldehyde. The 10% V2O5-1%MoO3/γ-Al2O3 was found in most active and selective catalyst during partial oxidation of n-hexane. The results indicated that by increasing the temperature, the n-hexane conversion increases as well, although the selectivity of the products passes through a maximum by increasing the temperature.

Measurements of HNO3 and N2O5 using Ion drift - Chemical Ionization Mass Spectrometry during the MCMA - 2006 Campaign

NASA Astrophysics Data System (ADS)

Zheng, J.; Zhang, R.; Fortner, E. C.; Molina, L.; Aiken, A. C.; Jimenez, J. L.; Gäggeler, K.; Dommen, J.; Dusanter, S.; Stevens, P. S.; Tie, X.

2008-03-01

An ion drift - chemical ionization mass spectrometry (ID-CIMS) was deployed in Mexico City between 5 and 31 March to measure HNO3 and N2O5 during the 2006 Mexico City Metropolitan Area (MCMA) field campaign. The observation site, T0, was located at the Instituto Mexicano del Petróleo at the center of the Mexico City Basin with major emissions of pollutants from both domestic and industrial sources. Diurnally, HNO3 was less than 200 parts per trillion (ppt) during the night and in the early morning, increased steadily from around 09:00 a.m. central standard time (CST), reached a peak value of 0.5 to 3 parts per billion (ppb) in the early afternoon, and declined sharply to less than half of the peak value near 05:00 p.m. CST. An inter-comparison between the ID-CIMS and an ion chromatograph/mass spectrometer (ICMS) showed a good correlation in the HNO3 measurements (R2=0.75). The HNO3 mixing ratio was found to anti-correlate with aerosol nitrate, suggesting that the gaseous HNO3 concentration was controlled by the gas-particle partitioning process. During most times of the MCMA 2006 field campaign, N2O5 was found to be under the detection limit (about 20 ppt for a 10 s integration time) of the ID-CIMS, because of high NO mixing ratio (>100 ppb) during the night. With one exception on 26 March 2006, about 40 ppt N2O5 was observed during the late afternoon and early evening hours under a cloudy condition, before NO built up at the surface site. The results revealed that during the 2006 MCMA field campaign HNO3 was primarily produced by the reaction of OH with NO2 and regulated by gas/particle partitioning, and HNO3 production from N2O5 hydrolysis during the nighttime was small because of high NO and low O3 concentrations near the surface.

Photomixotrophic chemical production in cyanobacteria.

PubMed

Matson, Morgan M; Atsumi, Shota

2018-04-01

The current global dependence on fossil fuels for both energy and chemical production has spurred concerns regarding long-term resource security and environmental detriments resulting from increased CO 2 levels. Through the installation of exogenous metabolic pathways, engineered cyanobacteria strains can directly fix CO 2 into industrially relevant chemicals currently produced from petroleum. This review highlights some of the studies that have successfully implemented photomixotrophic conditions to increase cyanobacterial chemical production. Supplementation with fixed carbon sources provides additional carbon building blocks and energy to enhance production and occasionally aid in growth. Photomixotrophic production has increased titers up to 5-fold over traditional autotrophic conditions, demonstrating promising applications for future commercialization. Copyright © 2017 Elsevier Ltd. All rights reserved.

Thermodynamic Properties of α-Fe 2O 3 and Fe 3O 4 Nanoparticles

DOE PAGES

Spencer, Elinor C.; Ross, Nancy L.; Olsen, Rebecca E.; ...

2015-04-21

Here we comprehansively assessed the thermodynamic properties of hydrated α-Fe 2O 3 (hematite) and Fe 3O 4 (magnetite) nanoparticles. In addition to 9 nm Fe 3O 4, three α-e 2O 3nanoparticles samples of different sizes (11, 14, and 25 nm) and bulk α-e 2O 3 have been evaluated by inelastic neutron scattering methods. The contribution of the two-level magnetic spin flip transition to the heat capacity of the α-e 2O 3 particles has been determined. The isochoric heat capacity of the water confined on the surface of these two types of iron oxide particles have been calculated from their INSmore » spectra, and is affected by the chemical composition of the underlying particle. Furthermore, the heat capacity and dynamics of the particle hydration layers appear to be influenced by a complex array of factors including particle size, water coverage, and possibly the magnetic state of the particle itself.« less

Primary emissions and chemical oxidation of volatile organic compounds emitted from laboratory biomass burning sources during the 2016 FIREX FireLab campaign: measurements from a H3O+ chemical ionization mass spectrometer

NASA Astrophysics Data System (ADS)

Coggon, M. M.; Warneke, C.; Koss, A.; Sekimoto, K.; Yuan, B.; Lim, C. Y.; Hagan, D. H.; Kroll, J. H.; Cappa, C. D.; Gilman, J.; Lerner, B. M.; Jimenez, J. L.; Yokelson, R. J.; Roberts, J. M.; De Gouw, J. A.

2017-12-01

Non-methane organic gases (NMOG) emitted by biomass burning constitute a large source of reactive carbon in the atmosphere. Once emitted, these compounds may undergo series of reactions with the OH radical and nitrogen oxides to form secondary organic aerosol (SOA), ozone, or other health-impacting products. The complex emission profile and strong variability of biomass burning NMOG play an important, yet understudied, role in the variability of air quality outcomes such as SOA and ozone. In this study, we summarize measurements of biomass burning volatile organic compounds (VOCs) conducted using a H3O+ chemical ionization mass spectrometer (H3O+-CIMS) during the 2016 FIREX laboratory campaign in Missoula, MT. Specifically, we will present data demonstrating the chemical evolution of biomass burning VOCs artificially aged in a field-deployable photooxidation chamber and an oxidation flow reactor. More than 50 OH-oxidation experiments were conducted with biomass types representing a range of North American fuels. Across many fuel types, VOCs with high SOA and ozone formation potential, such as aromatics and furans, were observed to quickly react with the OH radical while oxidized species were generated. We compare the calculated OH reactivity of the primary emissions to the calculated OH reactivity used in many photochemical models and highlight areas requiring additional research in order to improve model/measurement comparisons.

Low-temperature growth of highly crystalline β-Ga2O3 nanowires by solid-source chemical vapor deposition

PubMed Central

2014-01-01

Growing Ga2O3 dielectric materials at a moderately low temperature is important for the further development of high-mobility III-V semiconductor-based nanoelectronics. Here, β-Ga2O3 nanowires are successfully synthesized at a relatively low temperature of 610°C by solid-source chemical vapor deposition employing GaAs powders as the source material, which is in a distinct contrast to the typical synthesis temperature of above 1,000°C as reported by other methods. In this work, the prepared β-Ga2O3 nanowires are mainly composed of Ga and O elements with an atomic ratio of approximately 2:3. Importantly, they are highly crystalline in the monoclinic structure with varied growth orientations in low-index planes. The bandgap of the β-Ga2O3 nanowires is determined to be 251 nm (approximately 4.94 eV), in good accordance with the literature. Also, electrical characterization reveals that the individual nanowire has a resistivity of up to 8.5 × 107 Ω cm, when fabricated in the configuration of parallel arrays, further indicating the promise of growing these highly insulating Ga2O3 materials in this III-V nanowire-compatible growth condition. PACS 77.55.D; 61.46.Km; 78.40.Fy PMID:25114641

Low-temperature growth of highly crystalline β-Ga2O3 nanowires by solid-source chemical vapor deposition.

PubMed

Han, Ning; Wang, Fengyun; Yang, Zaixing; Yip, SenPo; Dong, Guofa; Lin, Hao; Fang, Ming; Hung, TakFu; Ho, Johnny C

2014-01-01

Growing Ga2O3 dielectric materials at a moderately low temperature is important for the further development of high-mobility III-V semiconductor-based nanoelectronics. Here, β-Ga2O3 nanowires are successfully synthesized at a relatively low temperature of 610°C by solid-source chemical vapor deposition employing GaAs powders as the source material, which is in a distinct contrast to the typical synthesis temperature of above 1,000°C as reported by other methods. In this work, the prepared β-Ga2O3 nanowires are mainly composed of Ga and O elements with an atomic ratio of approximately 2:3. Importantly, they are highly crystalline in the monoclinic structure with varied growth orientations in low-index planes. The bandgap of the β-Ga2O3 nanowires is determined to be 251 nm (approximately 4.94 eV), in good accordance with the literature. Also, electrical characterization reveals that the individual nanowire has a resistivity of up to 8.5 × 10(7) Ω cm, when fabricated in the configuration of parallel arrays, further indicating the promise of growing these highly insulating Ga2O3 materials in this III-V nanowire-compatible growth condition. 77.55.D; 61.46.Km; 78.40.Fy.

The electrical properties of low pressure chemical vapor deposition Ga doped ZnO thin films depending on chemical bonding configuration

NASA Astrophysics Data System (ADS)

Jung, Hanearl; Kim, Doyoung; Kim, Hyungjun

2014-04-01

The electrical and chemical properties of low pressure chemical vapor deposition (LP-CVD) Ga doped ZnO (ZnO:Ga) films were systematically investigated using Hall measurement and X-ray photoemission spectroscopy (XPS). Diethylzinc (DEZ) and O2 gas were used as precursor and reactant gas, respectively, and trimethyl gallium (TMGa) was used as a Ga doping source. Initially, the electrical properties of undoped LP-CVD ZnO films depending on the partial pressure of DEZ and O2 ratio were investigated using X-ray diffraction (XRD) by changing partial pressure of DEZ from 40 to 140 mTorr and that of O2 from 40 to 80 mTorr. The resistivity was reduced by Ga doping from 7.24 × 10-3 Ω cm for undoped ZnO to 2.05 × 10-3 Ω cm for Ga doped ZnO at the TMG pressure of 8 mTorr. The change of electric properties of Ga doped ZnO with varying the amount of Ga dopants was systematically discussed based on the structural crystallinity and chemical bonding configuration, analyzed by XRD and XPS, respectively.

Plasma-catalyst hybrid reactor with CeO2/γ-Al2O3 for benzene decomposition with synergetic effect and nano particle by-product reduction.

PubMed

Mao, Lingai; Chen, Zhizong; Wu, Xinyue; Tang, Xiujuan; Yao, Shuiliang; Zhang, Xuming; Jiang, Boqiong; Han, Jingyi; Wu, Zuliang; Lu, Hao; Nozaki, Tomohiro

2018-04-05

A dielectric barrier discharge (DBD) catalyst hybrid reactor with CeO 2 /γ-Al 2 O 3 catalyst balls was investigated for benzene decomposition at atmospheric pressure and 30 °C. At an energy density of 37-40 J/L, benzene decomposition was as high as 92.5% when using the hybrid reactor with 5.0wt%CeO 2 /γ-Al 2 O 3 ; while it was 10%-20% when using a normal DBD reactor without a catalyst. Benzene decomposition using the hybrid reactor was almost the same as that using an O 3 catalyst reactor with the same CeO 2 /γ-Al 2 O 3 catalyst, indicating that O 3 plays a key role in the benzene decomposition. Fourier transform infrared spectroscopy analysis showed that O 3 adsorption on CeO 2 /γ-Al 2 O 3 promotes the production of adsorbed O 2 - and O 2 2‒ , which contribute benzene decomposition over heterogeneous catalysts. Nano particles as by-products (phenol and 1,4-benzoquinone) from benzene decomposition can be significantly reduced using the CeO 2 /γ-Al 2 O 3 catalyst. H 2 O inhibits benzene decomposition; however, it improves CO 2 selectivity. The deactivated CeO 2 /γ-Al 2 O 3 catalyst can be regenerated by performing discharges at 100 °C and 192-204 J/L. The decomposition mechanism of benzene over CeO 2 /γ-Al 2 O 3 catalyst was proposed. Copyright © 2017 Elsevier B.V. All rights reserved.

Separation of thiol and cyanide hydrolysis products of chemical warfare agents by capillary electrophoresis.

PubMed

Copper, Christine L; Collins, Greg E

2004-03-01

The fluorescence derivatizing agent, o-phthalaldehyde (OPA), has been applied to the separation and detection of cyanide and several structurally similar thiols by capillary electrophoresis (CE)-laser induced fluorescence (LIF). Of particular interest to this investigation was the separation of 2-dimethylaminoethanethiol, 2-diethylaminoethanethiol, and cyanide, each of which are hydrolysis products or hydrolysis product simulants of the chemical warfare (CW) agents O-ethyl S-2-diisopropylaminoethyl methylphosphonothiolate (VX), O-isobutyl S-2-diethylaminoethyl methylphosphonothiolate (R-VX), and tabun (GA). Other structurally similar thiols simultaneously resolved by this method include 1-pentanethiol and 2-mercaptoethanol. Instrumental parameters were probed and optimum values for capillary length (50 cm) and inner diameter (75 microm), injection time (30 s) and field strength (15 kV) were determined. Sample stacking methods enabled detection limits of 9.3 microg/L for cyanide, 1.8 microg/L for 2-diethylaminoethanethiol, 35 microg/L for 2-dimethylaminoethanethiol, 15 microg/L for 2-mercaptoethanol, and 89 microg/L for 1-pentanethiol. The linearity of the method was verified over an order of magnitude and the reproducibility was found to be 3.0%.

Application of Chemical Doping and Architectural Design Principles To Fabricate Nanowire Co2Ni3ZnO8 Arrays for Aqueous Asymmetric Supercapacitors.

PubMed

Liu, Qi; Yang, Bin; Liu, Jingyuan; Yuan, Yi; Zhang, Hongsen; Liu, Lianhe; Wang, Jun; Li, Rumin

2016-08-10

Electrode materials derived from transition metal oxides have a serious problem of low electron transfer rate, which restricts their practical application. However, chemically doped graphene transforms the chemical bonding configuration to enhance electron transfer rate and, therefore, facilitates the successful fabrication of Co2Ni3ZnO8 nanowire arrays. In addition, the Co2Ni3ZnO8 electrode materials, considered as Ni and Zn ions doped into Co3O4, have a high electron transfer rate and electrochemical response capability, because the doping increases the degree of crystal defect and reaction of Co/Ni ions with the electrolyte. Hence, the Co2Ni3ZnO8 electrode exhibits a high rate property and excellent electrochemical cycle stability, as determined by electrochemical analysis of the relationship between specific capacitance, IR drop, Coulomb efficiency, and different current densities. From the results of a three-electrode system of electrochemical measurement, the Co2Ni3ZnO8 electrode demonstrates a specific capacitance of 1115 F g(-1) and retains 89.9% capacitance after 2000 cycles at a current density of 4 A g(-1). The energy density of the asymmetric supercapacitor (AC//Co2Ni3ZnO8) is 54.04 W h kg(-1) at the power density of 3200 W kg(-1).

Method for generating a crystalline {sup 99}MoO{sub 3} product and the isolation {sup 99m}Tc compositions therefrom

DOEpatents

Bennett, R.G.; Christian, J.D.; Kirkham, R.J.; Tranter, T.J.

1998-09-01

An improved method is described for producing {sup 99m}Tc compositions. {sup 100}Mo metal is irradiated with photons in a particle (electron) accelerator to produce {sup 99}Mo metal which is dissolved in a solvent. A solvated {sup 99}Mo product is then dried to generate a supply of {sup 99}MoO{sub 3} crystals. The crystals are thereafter heated at a temperature which will sublimate the crystals and form a gaseous mixture containing vaporized {sup 99m}TcO{sub 3} and vaporized {sup 99m}TcO{sub 2} but will not cause the production of vaporized {sup 99}MoO{sub 3}. The mixture is then combined with an oxidizing gas to generate a gaseous stream containing vaporized {sup 99m}Tc{sub 2}O{sub 7}. Next, the gaseous stream is cooled to a temperature sufficient to convert the vaporized {sup 99m}Tc{sub 2}O{sub 7} into a condensed {sup 99m}Tc-containing product. The product has high purity levels resulting from the use of reduced temperature conditions and ultrafine crystalline {sup 99}MoO{sub 3} starting materials with segregated {sup 99m}Tc compositions therein which avoid the production of vaporized {sup 99}MoO{sub 3} contaminants. 1 fig.

Method for generating a crystalline .sup.99 MoO.sub.3 product and the isolation .sup.99m Tc compositions therefrom

DOEpatents

Bennett, Ralph G.; Christian, Jerry D.; Kirkham, Robert J.; Tranter, Troy J.

1998-01-01

An improved method for producing .sup.99m Tc compositions. .sup.100 Mo metal is irradiated with photons in a particle (electron) accelerator to produce .sup.99 Mo metal which is dissolved in a solvent. A solvated .sup.99 Mo product is then dried to generate a supply of .sup.99 MoO.sub.3 crystals. The crystals are thereafter heated at a temperature which will sublimate the crystals and form a gaseous mixture containing vaporized .sup.99m TcO.sub.3 and vaporized .sup.99m TcO.sub.2 but will not cause the production of vaporized .sup.99 MoO.sub.3. The mixture is then combined with an oxidizing gas to generate a gaseous stream containing vaporized .sup.99m Tc.sub.2 O.sub.7. Next, the gaseous stream is cooled to a temperature sufficient to convert the vaporized .sup.99m Tc.sub.2 O.sub.7 into a condensed .sup.99m Tc-containing product. The product has high purity levels resulting from the use of reduced temperature conditions and ultrafine crystalline .sup.99 MoO.sub.3 starting materials with segregated .sup.99m Tc compositions therein which avoid the production of vaporized .sup.99 MoO.sub.3 contaminants.

Quantum Chemical Study of CH3 + O2 Combustion Reaction System: Catalytic Effects of Additional CO2 Molecule.

PubMed

Masunov, Artëm E; Wait, Elizabeth; Vasu, Subith S

2017-08-03

The supercritical carbon dioxide diluent is used to control the temperature and to increase the efficiency in oxycombustion fossil fuel energy technology. It may affect the rates of combustion by altering mechanisms of chemical reactions, compared to the ones at low CO 2 concentrations. Here, we investigate potential energy surfaces of the four elementary reactions in the CH 3 + O 2 reactive system in the presence of one CO 2 molecule. In the case of reaction CH 3 + O 2 → CH 2 O + OH (R1 channel), van der Waals (vdW) complex formation stabilizes the transition state and reduces the activation barrier by ∼2.2 kcal/mol. Alternatively, covalently bonded CO 2 may form a six-membered ring transition state and reduce the activation barrier by ∼0.6 kcal/mol. In case of reaction CH 3 + O 2 → CH 3 O + O (R2 channel), covalent participation of CO 2 lowers the barrier for the rate limiting step by 3.9 kcal/mol. This is expected to accelerate the R2 process, important for the branching step of the radical chain reaction mechanism. For the reaction CH 3 + O 2 → CHO + H 2 O (R3 channel) with covalent participation of CO 2 , the activation barrier is lowered by 0.5 kcal/mol. The reaction CH 2 O + OH → CHO + H 2 O (R4 channel) involves hydrogen abstraction from formaldehyde by OH radical. Its barrier is reduced from 7.1 to 0.8 kcal/mol by formation of vdW complex with spectator CO 2 . These new findings are expected to improve the kinetic reaction mechanism describing combustion processes in supercritical CO 2 medium.

Thermodynamic stability of stoichiometric LaFeO3 and BiFeO3: a hybrid DFT study.

PubMed

Heifets, Eugene; Kotomin, Eugene A; Bagaturyants, Alexander A; Maier, Joachim

2017-02-01

BiFeO 3 perovskite attracts great attention due to its multiferroic properties and potential use as a parent material for Bi 1-x Sr x FeO 3-δ and Bi 1-x Sr x Fe 1-y Co y O 3-δ solid solutions in intermediate temperature cathodes of oxide fuel cells. Another iron-based LaFeO 3 perovskite is the end member for well-known solid solutions (La 1-x Sr x Fe 1-y Co y O 3-δ ) used for oxide fuel cells and other electrochemical devices. In this study an ab initio hybrid functional approach was used for the study of the thermodynamic stability of both LaFeO 3 and BiFeO 3 with respect to decompositions to binary oxides and to elements, as a function of temperature and oxygen pressure. The localized (LCAO) basis sets describing the crystalline electron wave functions were carefully re-optimized within the CRYSTAL09 computer code. The results obtained by considering Fe as an all-electron atom and within the effective core potential technique are compared in detail. Based on our calculations, the phase diagrams were constructed allowing us to predict the stability region of stoichiometric materials in terms of atomic chemical potentials. This permits determining the environmental conditions for the existence of stable BiFeO 3 and LaFeO 3 . These conditions were presented as contour maps of oxygen atoms' chemical potential as a function of temperature and partial pressure of oxygen gas. A similar analysis was also performed using the experimental Gibbs energies of formation. The obtained phase diagrams and contour maps are compared with the calculated ones.

Quenching of I(2P 1/2) by O 3 and O( 3P)

NASA Astrophysics Data System (ADS)

Azyazov, V. N.; Antonov, I. O.; Ruffner, S.; Heaven, M. C.

2006-02-01

Oxygen-iodine lasers that utilize electrical or microwave discharges to produce singlet oxygen are currently being developed. The discharge generators differ from conventional chemical singlet oxygen generators in that they produce significant amounts of atomic oxygen. Post-discharge chemistry includes channels that lead to the formation of ozone. Consequently, removal of I(2P 1/2) by O atoms and O 3 may impact the efficiency of discharge driven iodine lasers. In the present study we have measured the rate constants for quenching of I(2P 1/2) by O( 3P) atoms and O 3 using pulsed laser photolysis techniques. The rate constant for quenching by O 3, 1.8x10 -12 cm 3 s -1, was found to be a factor of five smaller than the literature value. The rate constant for quenching by O( 3P) was 1.2x10 -11 cm 3 s -1. This was six times larger than a previously reported upper bound, but consistent with estimates obtained by modeling the kinetics of discharge-driven laser systems.

Chemical dissolution of sulfide minerals

USGS Publications Warehouse

Chao, T.T.; Sanzolone, R.F.

1977-01-01

Chemical dissolution treatments involving the use of aqua regia, 4 N HNO3, H2O2-ascorbic acid, oxalic acid, KClO3+HCl, and KClO3+HCl followed by 4 N HNO3 were applied to specimens of nine common sulfide minerals (galena, chalcopyrite, cinnabar, molybdenite, orpiment, pyrite, stibnite, sphalerite, and tetrahedrite) mixed individually with a clay loam soil. The resultant decrease in the total sulfur content of the mixture, as determined by using the Leco induction furnace, was used to evaluate the effectiveness of each chemical treatment. A combination of KClO3+HCl followed by 4 N HNO3 boiling gently for 20 min has been shown to be very effective in dissolving all the sulfide minerals. This treatment is recommended to dissolve metals residing in sulfide minerals admixed with secondary weathering products, as one step in a fractionation scheme whereby metals in soluble and adsorbed forms, and those associated with organic materials and secondary oxides, are first removed by other chemical extractants.

Dy3TaO7, A stoichiometric spin glass and the effect of disorder via chemical substitution in the Dy3-xYxTaO7 (0 ≤ x ≤ 3) solid solution

NASA Astrophysics Data System (ADS)

Gómez-García, J. Francisco; Bucio, Lauro; Tavizon, Gustavo

2018-01-01

In this work, we present both structural and magnetic (DC magnetization and AC susceptibility) studies of the Dy3-xYxTaO7 solid solution. The structural characterization of samples was performed by Rietveld refinements of the X-ray diffraction data. All compounds crystallized in a weberite-related structure in the orthorhombic C2221 space group (No. 20); the variations of the lattice parameters obey the Vegard´s law in the whole range of composition. DC magnetic measurements of the Dy3-xYxTaO7 system showed a Curie-Weiss paramagnetic behaviour, with antiferromagnetic interactions at T>150 K. Below 3 K a spin glass behaviour in the 0 ≤ x ≤ 1 range of the solid solution was observed. The stoichiometric Dy3TaO7 compound showed spin glass behaviour although there is no evidence of structural disorder. For some Y3+ doped compounds (x = 0.33, 0.66 and 1.0), chemical disorder reduced the freezing temperature (Tg) values with a ×1/3 dependence. Cole-Cole analysis of the AC magnetic field response showed similar phenomenological parameters for the stoichiometric (x = 0) and the Y3+ doped compounds with spin glassiness, suggesting an analogous mechanism for these compounds. For the Dy3-xYxTaO7 system, in which the spin glass behaviour seems to exhibit a critical concentration, a magnetic phase diagram is proposed.

40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN P-00... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Barium manganese oxide (BaMnO3). 721...

40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN P-00... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Barium manganese oxide (BaMnO3). 721...

40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN P-00...

40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN P-00...

40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN P-00...

40 CFR 721.10008 - Manganese strontium oxide (MnSrO3).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Manganese strontium oxide (MnSrO3... Specific Chemical Substances § 721.10008 Manganese strontium oxide (MnSrO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as manganese strontium oxide...

40 CFR 721.10008 - Manganese strontium oxide (MnSrO3).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Manganese strontium oxide (MnSrO3... Specific Chemical Substances § 721.10008 Manganese strontium oxide (MnSrO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as manganese strontium oxide...

40 CFR 721.10008 - Manganese strontium oxide (MnSrO3).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Manganese strontium oxide (MnSrO3... Specific Chemical Substances § 721.10008 Manganese strontium oxide (MnSrO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as manganese strontium oxide...

40 CFR 721.10008 - Manganese strontium oxide (MnSrO3).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Manganese strontium oxide (MnSrO3... Specific Chemical Substances § 721.10008 Manganese strontium oxide (MnSrO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as manganese strontium oxide...

40 CFR 721.10008 - Manganese strontium oxide (MnSrO3).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Manganese strontium oxide (MnSrO3... Specific Chemical Substances § 721.10008 Manganese strontium oxide (MnSrO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as manganese strontium oxide...

Reducing N2O and NO emissions while sustaining crop productivity in a Chinese vegetable-cereal double cropping system.

PubMed

Yao, Zhisheng; Yan, Guangxuan; Zheng, Xunhua; Wang, Rui; Liu, Chunyan; Butterbach-Bahl, Klaus

2017-12-01

High nitrogen (N) inputs in Chinese vegetable and cereal productions played key roles in increasing crop yields. However, emissions of the potent greenhouse gas nitrous oxide (N 2 O) and atmospheric pollutant nitric oxide (NO) increased too. For lowering the environmental costs of crop production, it is essential to optimize N strategies to maintain high crop productivity, while reducing the associated N losses. We performed a 2 year-round field study regarding the effect of different combinations of poultry manure and chemical N fertilizers on crop yields, N use efficiency (NUE) and N 2 O and NO fluxes from a Welsh onion-winter wheat system in the North China Plain. Annual N 2 O and NO emissions averaged 1.14-3.82 kg N ha -1 yr -1 (or 5.54-13.06 g N kg -1 N uptake) and 0.57-1.87 kg N ha -1 yr -1 (or 2.78-6.38 g N kg -1 N uptake) over all treatments, respectively. Both N 2 O and NO emissions increased linearly with increasing total N inputs, and the mean annual direct emission factors (EF d ) were 0.39% for N 2 O and 0.19% for NO. Interestingly, the EF d for chemical N fertilizers (N 2 O: 0.42-0.48%; NO: 0.07-0.11%) was significantly lower than for manure N (N 2 O: 1.35%; NO: 0.76%). Besides, a negative power relationship between yield-scaled N 2 O, NO or N 2 O + NO emissions and NUE was observed, suggesting that improving NUE in crop production is crucial for increasing crop yields while decreasing nitrogenous gas release. Compared to the current farmers' fertilization rate, alternative practices with reduced chemical N fertilizers increased NUE and decreased annual N 2 O + NO emissions substantially, while crop yields remained unaffected. As a result, annual yield-scaled N 2 O + NO emissions were reduced by > 20%. Our study shows that a reduction of current application rates of chemical N fertilizers by 30-50% does not affect crop productivity, while at the same time N 2 O and NO emissions would be reduced significantly. Copyright © 2017 Elsevier Ltd. All rights

Evaluating microbial chemical choices: The ocean chemistry basis for the competition between use of O2 or NO3- as an electron acceptor

NASA Astrophysics Data System (ADS)

Brewer, Peter G.; Hofmann, Andreas F.; Peltzer, Edward T.; Ussler, William, III

2014-05-01

The traditional ocean chemical explanation for the emergence of suboxia is that once O2 levels decline to about 10 μmol kg-1 then onset of NO3- reduction occurs. This piece of ocean chemical lore is well founded in observations and is typically phrased as a microbial choice and not as an obligate requirement. The argument based on O2 levels alone could also be phrased as being dependent on an equivalent amount of NO3- that would yield the same energy gain. This description is based on the availability of the electron acceptor: but the oxidation reactions are usually written out as free energy yield per mole of organic matter, thus not addressing the oxidant availability constraint invoked by ocean scientists. Here we show that the argument can be phrased simply as competing rate processes dependent on the free energy yield ratio per amount of electron acceptor obtained, and thus the [NO3-]:[O2] molar ratio is the critical variable. The rate at which a microbe can acquire either O2 or NO3- to carry out the oxidation reactions is dependent on both the concentration in the bulk ocean, and on the diffusivity within the microbial external molecular boundary layer. From the free energy yield calculations combined with the ~25% greater diffusivity of the O2 molecule we find that the equivalent energy yield occurs at a ratio of about 3.8 NO3-:O2 for a typical Redfield ratio reaction, consistent with an ocean where NO3- reduction onset occurs at about 10 μmol O2:40 μmol NO3-, and the reactions then proceed in parallel along a line of this slope until the next energy barrier is approached. Within highly localized microbial consortia intensely reducing pockets may occur in a bulk ocean containing finite low O2 levels; and the local flux of reduced species from strongly reducing shelf sediments will perturb the large scale water column relationship. But all localized reactions drive towards maximal energy gain from their immediate diffusive surroundings, thus the ocean

Effect of surface Fe-S hybrid structure on the activity of the perfect and reduced α-Fe2O3(001) for chemical looping combustion

NASA Astrophysics Data System (ADS)

Xiao, Xianbin; Qin, Wu; Wang, Jianye; Li, Junhao; Dong, Changqing

2018-05-01

Sulfurization of the gradually reduced Fe2O3 surfaces is inevitable while Fe2O3 is used as an oxygen carrier (OC) for coal chemical looping combustion (CLC), which will result in formation of Fe-S hybrid structure on the surfaces. The Fe-S hybrid structure will directly alter the reactivity of the surfaces. Therefore, detailed properties of Fe-S hybrid structure over the perfect and reduced Fe2O3(001) surfaces, and its effect on the interfacial interactions, including CO oxidization and decomposition on the surfaces, were investigated by using density functional theory (DFT) calculations. The S atom prefers to chemically bind to Fe site with electron transfer from the surfaces to the S atom, and a deeper reduction of Fe2O3(001) leads to an increasing interaction between S and Fe. The formation of Fe-S hybrid structure alters the electronic properties of the gradually reduced Fe2O3(001) surfaces, promoting CO oxidation on the surfaces ranging from Fe2O3 to FeO, but depressing carbon deposition on the surfaces ranging from FeO to Fe. The sulfurized FeO acts as a watershed to realize relatively high CO oxidation rate and low carbon deposition. Results provided a fundamental understanding for controlling and optimizing the CLC processes.

A selected ion flow tube study of the reactions of H3O+, NO+ and O2+ with some oxygenated biogenic volatile organic compounds

NASA Astrophysics Data System (ADS)

Amelynck, C.; Schoon, N.; Kuppens, T.; Bultinck, P.; Arijs, E.

2005-12-01

The rate constants and product ion distributions of the reactions of H3O+, NO+ and O2+ with 2-methyl-3-buten-2-ol, cis-3-hexen-1-ol, cis-3-hexenyl acetate, 1,8-cineole, 6-methyl-5-hepten-2-one, camphor and linalool have been determined at 150 Pa and 297 K using a selected ion flow tube (SIFT). All reactions were found to proceed at a rate close to the collision rate, calculated with the Su and Chesnavich model, using the polarizability and electric dipole moment of the compounds derived from B3LYP/aug-cc-pVDZ quantum chemical calculations. Additionally the product ion distributions of the reactions of these three ions with the terpenoid alcohols nerol and geraniol have been obtained.

Construction of viscosity diagrams for CaO-SiO2-Al2O3-8% MgO-4% B2O3 slags by the simplex lattice method

NASA Astrophysics Data System (ADS)

Babenko, A. A.; Istomin, S. A.; Zhuchkov, V. I.; Sychev, A. V.; Ryabov, V. V.; Upolovnikova, A. G.

2017-05-01

The simplex lattice method of planning experiments is used to study the viscosities of CaO-SiO2-Al2O3-8% MgO-4% B2O3 slags in a wide chemical composition range. For each viscosity, we developed an adequate mathematical model in the form of a reduced third-order polynomial. The results of mathematical simulation are presented in composition-viscosity diagrams. Composition regions with a high fluidity of slags, the viscosities of which are 0.8-1.2 Pa s in the temperature range 1500-1600°C, are indicated in the diagrams.

Observations of VOC emissions and photochemical products over US oil- and gas-producing regions using high-resolution H3O+ CIMS (PTR-ToF-MS)

NASA Astrophysics Data System (ADS)

Koss, Abigail; Yuan, Bin; Warneke, Carsten; Gilman, Jessica B.; Lerner, Brian M.; Veres, Patrick R.; Peischl, Jeff; Eilerman, Scott; Wild, Rob; Brown, Steven S.; Thompson, Chelsea R.; Ryerson, Thomas; Hanisco, Thomas; Wolfe, Glenn M.; St. Clair, Jason M.; Thayer, Mitchell; Keutsch, Frank N.; Murphy, Shane; de Gouw, Joost

2017-08-01

VOCs related to oil and gas extraction operations in the United States were measured by H3O+ chemical ionization time-of-flight mass spectrometry (H3O+ ToF-CIMS/PTR-ToF-MS) from aircraft during the Shale Oil and Natural Gas Nexus (SONGNEX) campaign in March-April 2015. This work presents an overview of major VOC species measured in nine oil- and gas-producing regions, and a more detailed analysis of H3O+ ToF-CIMS measurements in the Permian Basin within Texas and New Mexico. Mass spectra are dominated by small photochemically produced oxygenates and compounds typically found in crude oil: aromatics, cyclic alkanes, and alkanes. Mixing ratios of aromatics were frequently as high as those measured downwind of large urban areas. In the Permian, the H3O+ ToF-CIMS measured a number of underexplored or previously unreported species, including aromatic and cycloalkane oxidation products, nitrogen heterocycles including pyrrole (C4H5N) and pyrroline (C4H7N), H2S, and a diamondoid (adamantane) or unusual monoterpene. We additionally assess the specificity of a number of ion masses resulting from H3O+ ion chemistry previously reported in the literature, including several new or alternate interpretations.

Neodymium cobalt oxide as a chemical sensor

NASA Astrophysics Data System (ADS)

Abdel-Latif, I. A.; Rahman, Mohammed M.; Khan, Sher Bahadar

2018-03-01

Chemical sensing and electrical transport properties of neodymium coblate, NdCoO3, was investigated in this work. It was prepared by using co-precipitation method. Pure neodymium chloride and cobalt chloride were mixing in the presence of sodium hydroxide and the obtained co-precipitated powder was calcined at 850 and 1000 °C. The synthesized composites, as-grown (NdCoO3-I), calcined at 850 °C (NdCoO3-II), and calcined at 1000 °C (NdCoO3-III) were studied in details in terms of their morphological and structural properties. The X-ray analysis confirmed that the synthesized products are well crystalline possessing single phase orthorhombic crystal system of space group Pbnm(62). The crystallite size of NdCoO3-I, NdCoO3-II, and NdCoO3-III is 22, 111, and 338 nm, respectively which reflect that crystallite size is increasing with increase in firing temperature. The DC resistivity was measured as a function of temperature in the temperature range from room temperature up to 200 °C. All NdCoO3 are semiconductor in this range of temperature but showed different activation energy which strongly depends on the crystallite size of the products. The activation energy decreased with increase in crystallite size, 0.798, 0.414 and 0.371 eV for NdCoO3-I, NdCoO3-II, and NdCoO3-III, respectively. Thus resistivity increases with increase in crystallite size of NdCoO3. All NdCoO3 products were tested as chemical sensor for acetone by electrochemical approaches and showed excellent sensitivity. Among the NdCoO3 samples, NdCoO3-III showed the highest sensitivity (3.4722 μAcm-2 mM-1) compared to other compositions and gradually decreased to 3.2407 μAcm-2 mM-1 with decreasing the crystallite size of NdCoO3-II. It is also observed that the sensitivity drastically decreased to 0.76253 μAcm-2 mM-1 in the case of NdCoO3-I. It is introduced an efficient route for the detection of environmental unsafe chemicals by electrochemical approach for the safety of healthcare and environmental

Syngas production by chemical-looping gasification of wheat straw with Fe-based oxygen carrier.

PubMed

Hu, Jianjun; Li, Chong; Guo, Qianhui; Dang, Jiatao; Zhang, Quanguo; Lee, Duu-Jong; Yang, Yunlong

2018-05-03

The iron-based oxygen carriers (OC's), Fe 2 O 3 /support (Al 2 O 3 , TiO 2 , SiO 2 and ZrO 2 ), for chemical looping gasification of wheat straw were prepared using impregnation method. The surface morphology, crystal structure, carbon deposition potential, lattice oxygen activity and selectivity of the yielded OCs were examined. The Fe 2 O 3 /Al 2 O 3 OCs at 60% loading has the highest H 2 yield, H 2 /CO ratio, gas yield, and carbon conversion amongst the tested OC's. Parametric studies revealed that an optimal loading Fe 2 O 3 of 60%, steam-to-biomass ratio of 0.8 and oxygen carrier-to-biomass ratio of 1.0 led to the maximum H 2 /CO ratio, gas yield, H 2  + CO ratio, and carbon conversion from the gasified wheat straw. High temperature, up to 950 °C, enhanced the gasification performance. A kinetic network interpreted the noted experimental results. The lattice oxygen provided by the prepared Fe 2 O 3 /Al 2 O 3 oxygen carriers promotes chemical looping gasification efficiencies from wheat straw. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ferromagnetic CaRuO3

PubMed Central

Tripathi, Shivendra; Rana, Rakesh; Kumar, Sanjay; Pandey, Parul; Singh, R. S.; Rana, D. S.

2014-01-01

The non-magnetic and non-Fermi-liquid CaRuO3 is the iso-structural analog of the ferromagnetic (FM) and Fermi-liquid SrRuO3. We show that an FM order in the orthorhombic CaRuO3 can be established by the means of tensile epitaxial strain. The structural and magnetic property correlations in the CaRuO3 films formed on SrTiO3 (100) substrate establish a scaling relation between the FM moment and the tensile strain. The strain dependent crossover from non-magnetic to FM CaRuO3 was observed to be associated with switching of non-Fermi liquid to Fermi-liquid behavior. The intrinsic nature of this strain-induced FM order manifests in the Hall resistivity too; the anomalous Hall component realizes in FM tensile-strained CaRuO3 films on SrTiO3 (100) whereas the non-magnetic compressive-strained films on LaAlO3 (100) exhibit only the ordinary Hall effect. These observations of an elusive FM order are consistent with the theoretical predictions of scaling of the tensile epitaxial strain and the magnetic order in tensile CaRuO3. We further establish that the tensile strain is more efficient than the chemical route to induce FM order in CaRuO3. PMID:24464302

Homoepitaxial growth of β-Ga{sub 2}O{sub 3} thin films by low pressure chemical vapor deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rafique, Subrina; Han, Lu; Zhao, Hongping, E-mail: hongping.zhao@case.edu

2016-05-02

This paper presents the homoepitaxial growth of phase pure (010) β-Ga{sub 2}O{sub 3} thin films on (010) β-Ga{sub 2}O{sub 3} substrate by low pressure chemical vapor deposition. The effects of growth temperature on the surface morphology and crystal quality of the thin films were systematically investigated. The thin films were synthesized using high purity metallic gallium (Ga) and oxygen (O{sub 2}) as precursors for gallium and oxygen, respectively. The surface morphology and structural properties of the thin films were characterized by atomic force microscopy, X-ray diffraction, and high resolution transmission electron microscopy. Material characterization indicates the growth temperature played anmore » important role in controlling both surface morphology and crystal quality of the β-Ga{sub 2}O{sub 3} thin films. The smallest root-mean-square surface roughness of ∼7 nm was for thin films grown at a temperature of 950 °C, whereas the highest growth rate (∼1.3 μm/h) with a fixed oxygen flow rate was obtained for the epitaxial layers grown at 850 °C.« less

MECHANICAL AND CHEMICAL PROPERTIES OF CEMENTITIOUS MATERIALS USING γ-2CaO.SiO2 UNDER THE SEVERAL CONDITIONS IN ACCELERATED CARBONATION CURING

NASA Astrophysics Data System (ADS)

Watanabe, Kenzo; Yokozeki, Kosuke; Torichigai, Takeshi; Sakai, Etsuo

The experiments have been conducted in order to investigate the mechanical and chemical properties of mortar with three different binders under the several conditions in accelerated carbonation curing. As the results, the depth of carbonation varied among each mix proportion. It is proven that by increasing CO2 density in the mortar having γ-2CaO.SiO2, the CaCO3 production will increase, which leads to the increase of filling ability in the pore of mortar. Furthermore, as a result from the calculation of Tritium permeation, it shows that the permeation decreases with an increase of CO2 density.

First-principles calculations of finite temperature Sc and O NMR parameters in Pb(Sc2/3W1/3)O3

NASA Astrophysics Data System (ADS)

Krakauer, Henry; Walter, Eric J.; Ellden, Jeremy; Hoatson, Gina L.; Vold, Robert L.

2012-02-01

Understanding the dynamics of complex relaxor ferroelectrics is important to characterizing their large electromechanical coupling. Preliminary NMR measurements of Sc electric-field-gradients (EFG) in Pb(Sc2/3W1/3)O3 (PSW) show a strong temperature dependence in the range T = 250 - 330 K. To understand this behavior, we use the first-principles GIPAWootnotetextC. J. Pickard and F. Mauri, Phys. Rev. B 63, 245101 (2001); method within the Quantum Espresso (QE) packageootnotetextP. Giannozzi et al., Journal of Physics: Condensed Matter 21, 395502 (2009) to calculate ^45Sc and ^17O chemical-shifts and EFG tensors. To study finite temperature effects, we incorporate the thermal expansion of the lattice and sample thermal disorder, using the phonon degrees of freedom. As in our previous studies of perovksites,ootnotetextD. L. Pechkis, E. J. Walter, and H. Krakauer. J. Chem. Phys. 135, 114507 (2011); ibid. 131, 184511 (2009) we show that the ^17O chemical shifts in PSW also exhibit a linear correlation with the nearest-neighbor B-O bond length.

A high-resolution time-of-flight chemical ionization mass spectrometer utilizing hydronium ions (H3O+ ToF-CIMS) for measurements of volatile organic compounds in the atmosphere

NASA Astrophysics Data System (ADS)

Yuan, Bin; Koss, Abigail; Warneke, Carsten; Gilman, Jessica B.; Lerner, Brian M.; Stark, Harald; de Gouw, Joost A.

2016-07-01

Proton transfer reactions between hydronium ions (H3O+) and volatile organic compounds (VOCs) provide a fast and highly sensitive technique for VOC measurements, leading to extensive use of proton-transfer-reaction mass spectrometry (PTR-MS) in atmospheric research. Based on the same ionization approach, we describe the development of a high-resolution time-of-flight chemical ionization mass spectrometer (ToF-CIMS) utilizing H3O+ as the reagent ion. The new H3O+ ToF-CIMS has sensitivities of 100-1000 cps ppb-1 (ion counts per second per part-per-billion mixing ratio of VOC) and detection limits of 20-600 ppt at 3σ for a 1 s integration time for simultaneous measurements of many VOC species of atmospheric relevance. The ToF analyzer with mass resolution (m/Δm) of up to 6000 allows the separation of isobaric masses, as shown in previous studies using similar ToF-MS. While radio frequency (RF)-only quadrupole ion guides provide better overall ion transmission than ion lens system, low-mass cutoff of RF-only quadrupole causes H3O+ ions to be transmitted less efficiently than heavier masses, which leads to unusual humidity dependence of reagent ions and difficulty obtaining a humidity-independent parameter for normalization. The humidity dependence of the instrument was characterized for various VOC species and the behaviors for different species can be explained by compound-specific properties that affect the ion chemistry (e.g., proton affinity and dipole moment). The new H3O+ ToF-CIMS was successfully deployed on the NOAA WP-3D research aircraft for the SONGNEX campaign in spring of 2015. The measured mixing ratios of several aromatics from the H3O+ ToF-CIMS agreed within ±10 % with independent gas chromatography measurements from whole air samples. Initial results from the SONGNEX measurements demonstrate that the H3O+ ToF-CIMS data set will be valuable for the identification and characterization of emissions from various sources, investigation of secondary

Synthesis, characterization and application of iron (II, III) oxide (Fe3O4) magnetic nanoparticles in mimic of wound healing model

NASA Astrophysics Data System (ADS)

Konyala, Divya

The research study focused on synthesis, characterization and applications of Fe3O4 core-shelled magnetic nanomaterials. This Fe3O4 magnetic nanomaterials will be prepared by using cost effective and convenient wet-chemistry method and will encapsulated using aqueous extracts of medicinal natural products. Three natural products namely Symplocos racemosa, Picrorhiza kurroa and Butea monosperma used to encapsulate Fe3O 4 MNMs due to their scope to reduce the risk of cancer, improves health, increase energy and enhance the immunity. These three medicinal natural products are synthesize by using water as a solvents to derive its active constituents, which will further used to functionalize the magnetic nanomaterials. The magnetic nanoparticles characterization studies performed using X-ray powder diffraction, Scanning electron microscope, Transmission electron microscope, Ultraviolet-visible spectroscopy, Fourier Transform Infrared spectroscopy (FT-IR) and Magnetic property. Fe3O4 magnetic nanomaterials biological activity was tested on Gram-negative bacteria (Escherichia coli). The results pointed out that, due to the adequate coating of Fe 3O4 (Iron Oxide) core by the medicinal chemical constituents from the natural products, the absorption of Fe3O4 magnetic nanomaterials was not detected in the UV-VIS Spectroscopy. TEM images showed that Fe3O4 coated with natural product extract in core-shelled structure, and the size of the particle ranges from 6 nm to 10 nm. Fourier Transform Infrared spectroscopy (FT-IR) was performed to determine the nature of chemicals present in natural extracts and functionalized Fe3O 4 magnetic nanomaterials. The model of wound healing mimic and antibacterial activity performed on gram-negative (Escherichia coli), indicating steady increasing cell growth after adding Fe3O4 MNMs. It was also found that MNMs synthesized at high temperatures shows less wound healing activity, when compared to MNMs prepared at room temperature due to formation

Realization of single terminated surface of perovskite oxide single crystals and their band profile: (LaAlO3)0.3(Sr2AlTaO6)0.7, SrTiO3 and KTaO3 case study

NASA Astrophysics Data System (ADS)

Tomar, Ruchi; Wadehra, Neha; Budhiraja, Vaishali; Prakash, Bhanu; Chakraverty, S.

2018-01-01

To characterize the physical properties of thin films without ambiguity and design interface with new functionalities, it is essential to have detailed knowledge of physical properties and appropriate estimation of the band profile of perovskite oxide substrates. We have developed and demonstrated a chemical free unified framework to realize single terminated surface of KTaO3, (LaAlO3)0.3 (Sr2AlTaO6)0.7 and SrTiO3 (001) oriented single crystals. The electronic band line-up of these single crystal substrates, using a combination of optical spectroscopy and Kelvin Probe Force Microscopy, has been constructed. A polar-polar interface of KTaO3 and LaBO3 (B-Transition metal ion) before and after the possible surface/electronic reconstruction has also been schematically presented.

Fabrication of graphene oxide decorated with Fe3O4@SiO2 for immobilization of cellulase

NASA Astrophysics Data System (ADS)

Li, Yue; Wang, Xiang-Yu; Jiang, Xiao-Ping; Ye, Jing-Jing; Zhang, Ye-Wang; Zhang, Xiao-Yun

2015-01-01

Fe3O4@SiO2-graphene oxide (GO) composites were successfully fabricated by chemical binding of functional Fe3O4@SiO2 and GO and applied to immobilization of cellulase via covalent attachment. The prepared composites were further characterized by transmission electron microscopy and Fourier transform infrared spectroscopy. Fe3O4 nanoparticles (NPs) were monodisperse spheres with a mean diameter of 17 ± 0.2 nm. The thickness of SiO2 layer was calculated as being 6.5 ± 0.2 nm. The size of Fe3O4@SiO2 NPs was 24 ± 0.3 nm, similar to that of Fe3O4@SiO2-NH2. Fe3O4@SiO2-GO composites were synthesized by linking of Fe3O4@SiO2-NH2 NPs to GO with the catalysis of EDC and NHS. The prepared composites were used for immobilization of cellulase. A high immobilization yield and efficiency of above 90 % were obtained after the optimization. The half-life of immobilized cellulase (722 min) was 3.34-fold higher than that of free enzyme (216 min) at 50 °C. Compared with the free cellulase, the optimal temperature of the immobilized enzyme was not changed; but the optimal pH was shifted from 5.0 to 4.0, and the thermal stability was enhanced. The immobilized cellulase could be easily separated and reused under magnetic field. These results strongly indicate that the cellulase immobilized onto the Fe3O4@SiO2-GO composite has potential applications in the production of bioethanol.

Nickel sulfide/graphitic carbon nitride/strontium titanate (NiS/g-C3N4/SrTiO3) composites with significantly enhanced photocatalytic hydrogen production activity.

PubMed

Luo, Xiu-Li; He, Gang-Ling; Fang, Yue-Ping; Xu, Yue-Hua

2018-05-15

NiS/g-C 3 N 4 /SrTiO 3 (NS/CN/STO) composites were prepared using a facile hydrothermal method. The synergistic effect of g-C 3 N 4 /SrTiO 3 (CN/STO) heterojunction and NiS cocatalyst enhanced the photocatalytic hydrogen evolution activity of NS/CN/STO. A hydrogen production rate of 1722.7 μmol h -1  g -1 was obtained when the 2%NiS/20%g-C 3 N 4 /SrTiO 3 (2NS/20CN/STO) was used for the photocatalytic hydrogen evolution in the presence of methanol used as a sacrificial agent under UV-vis light irradiation; the photocatalytic hydrogen production rate of 2NS/20CN/STO is 32.8, 8.9 and 4.2 times the value of that obtained with pure g-C 3 N 4 , SrTiO 3 and 20%g-C 3 N 4 /SrTiO 3 (20CN/STO), respectively. Moreover, in photoelectrochemical investigations when compared with 20CN/STO, SrTiO 3 and g-C 3 N 4 , 2NS/20CN/STO exhibited significant photocurrent enhancement. The heterojunction and cocatalyst in NS/CN/STO improved the charge separation efficiency and the lifetime of the charge carriers, leading to the enhanced generation of electrons for photocatalytic hydrogen production. Copyright © 2018 Elsevier Inc. All rights reserved.

Infrared and TPD studies of nitrates adsorbed on Tb{sub 4}O{sub 7}, La{sub 2}O{sub 3}, BaO, and MgO/{gamma}-Al{sub 2}O{sub 3}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chi, Y.; Chuang, S.S.C.

2000-05-18

NO and O{sub 2} coadsorption on {gamma}-Al{sub 2}O{sub 3}-supported Tb{sub 4}O{sub 7}, La{sub 2}O{sub 3}, BaO, and MgO has been investigated by in situ infrared spectroscopy coupled with temperature-programmed decomposition and desorption. BaO/{gamma}-Al{sub 2}O{sub 3} and MgO/{gamma}-Al{sub 2}O{sub 3} possess a higher NO{sub x} storage capability than Tb{sub 4}O{sub 7}/{gamma}-Al{sub 2}O{sub 3} and La{sub 2}O{sub 3}/{gamma}-Al{sub 2}O{sub 3}. NO/O{sub 2} coadsorbed on Tb{sub 4}O{sub 7}, La{sub 2}O{sub 3}, and BaO in the form of bridging bidentate, chelating bidentate, and monodentate nitrates, and on MgO in the form of bridging bidentate and monodentate nitrates via the reaction of adsorbed NO withmore » adsorbed oxygen at 298 K. NO/O{sub 2} coadsorbed as a chelating bidentate nitrate on Tb{sub 4}O{sub 7} and La{sub 2}O{sub 3}, and as a distinctive bridging bidentate nitrate on BaO and MgO via the reaction of adsorbed NO with surface lattice oxygen at 523 K. These various forms of adsorbed nitrate differ in structure and reactivity from Tb(NO{sub 3}){sub 3}, La(NO{sub 3}){sub 3}, Ba(NO{sub 3}){sub 2}, and Mg(NO{sub 3}){sub 2}, the precursor used to prepare metal oxides for NO/O{sub 2} coadsorption. Temperature-programmed desorption (TPD) of chelating bidentate nitrate on Tb{sub 4}O{sub 7}, La{sub 2}O{sub 3}, and BaO produced primarily NO and O{sub 2}, with maxima at 640 and 670 K, respectively. TPD of bridging bidentate nitrate and monodentate nitrate on Tb{sub 4}O{sub 7}, La{sub 2}O{sub 3}, and BaO produced NO and O{sub 2} as major products and N{sub 2} and N{sub 2}O as minor products, at 320--500 K. Decomposition of bridging bidentate on MgO produced NO as a major product and N{sub 2}O as a minor product at a peak temperature of 690 K. Peak temperatures for Tb(NO{sub 3}){sub 3}, La(NO{sub 3}){sub 3}, Ba(NO{sub 3}){sub 2}, and Mg(NO{sub 3}){sub 2} decomposition occurred between those for bridging and chelating nitrates. The difference in stability between

Metabolic engineering of Saccharomyces cerevisiae for production of very long chain fatty acid-derived chemicals.

PubMed

Yu, Tao; Zhou, Yongjin J; Wenning, Leonie; Liu, Quanli; Krivoruchko, Anastasia; Siewers, Verena; Nielsen, Jens; David, Florian

2017-05-26

Production of chemicals and biofuels through microbial fermentation is an economical and sustainable alternative for traditional chemical synthesis. Here we present the construction of a Saccharomyces cerevisiae platform strain for high-level production of very-long-chain fatty acid (VLCFA)-derived chemicals. Through rewiring the native fatty acid elongation system and implementing a heterologous Mycobacteria FAS I system, we establish an increased biosynthesis of VLCFAs in S. cerevisiae. VLCFAs can be selectively modified towards the fatty alcohol docosanol (C 22 H 46 O) by expressing a specific fatty acid reductase. Expression of this enzyme is shown to impair cell growth due to consumption of VLCFA-CoAs. We therefore implement a dynamic control strategy for separating cell growth from docosanol production. We successfully establish high-level and selective docosanol production of 83.5 mg l -1 in yeast. This approach will provide a universal strategy towards the production of similar high value chemicals in a more scalable, stable and sustainable manner.

Antimicrobial Activity of Al2O3, CuO, Fe3O4, and ZnO Nanoparticles in Scope of Their Further Application in Cement-Based Building Materials

PubMed Central

Cendrowski, Krzysztof; Nawrotek, Paweł; Mijowska, Ewa

2018-01-01

Nanoparticles were proposed as antibacterial cement admixtures for the production of cement-based composites. Nevertheless, the standards for evaluation of such admixtures still do not indicate which model organisms to use, particularly in regard to the further application of material. Apart from the known toxicity of nanomaterials, in the case of cement-based composites there are limitations associated with the mixing and dispersion of nanomaterials. Therefore, four nanooxides (Al2O3, CuO, Fe3O4, and ZnO) and seven microorganisms were tested to initially evaluate the applicability of nanooxides in relation to their further use in cement-based composites. Studies of nanoparticles included chemical analysis, microbial growth kinetics, 4- and 24 h toxicity, and biofilm formation assay. Nanooxides showed toxicity against microorganisms in the used concentration, although the populations were able to re-grow. Furthermore, the effect of action was variable even between strains from the same genus. The effect of nanoparticles on biofilms depended on the used strain. Gathered results show several problems that can occur while studying nanoparticles for specific further application. Proper protocols for nanomaterial dispersion prior the preparation of cement-based composites, as well as a standardized approach for their testing, are the fundamental issues that have to be resolved to produce efficient composites. PMID:29614721

Violet-green excitation for NIR luminescence of Yb3+ ions in Bi2O3-B2O3-SiO2-Ga2O3 glasses.

PubMed

Li, Weiwei; Cheng, Jimeng; Zhao, Guoying; Chen, Wei; Hu, Lili; Guzik, Malgorzata; Boulon, Georges

2014-04-21

60Bi(2)O(3)-20B(2)O(3)-10SiO(2)-10Ga(2)O(3) glasses doped with 1-9 mol% Yb(2)O(3) were prepared and investigated mainly on their violet-green excitation for the typical NIR emission of Yb(3+), generally excited in the NIR. Two violet excitation bands at 365 nm and 405 nm are related to Yb(2+) and Bi(3+). 465 nm excitation band and 480 nm absorption band in the blue-green are assigned to Bi(0) metal nanoparticles/grains. Yb-content-dependence of the excitation and absorption means that Bi(0) is the reduced product of Bi(3+), but greatly competed by the redox reaction of Yb(2+) ↔ Yb(3+). It is proved that the violet-green excitations result in the NIR emission of Yb(3+). On the energy transfer, the virtual level of Yb(3+)-Yb(3+) as well as Bi(0) dimers probably plays an important role. An effective and controllable way is suggested to achieve nano-optical applications by Bi(0) metal nanoparticles/grains and Yb(3+).

Summertime photochemistry during CAREBeijing-2007: ROx budgets and O3 formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Zhen; Wang, Y.; Gu, Dasa

2012-08-28

We analyze summertime photochemistry near the surface in Beijing, China, using a 1-D photochemical model (Regional chEmical and trAnsport Model, REAM-1D) constrained by in situ observations, focusing on the budgets of ROx (OH + HO2 + RO2) radicals and O3 formation. While the modeling analysis focuses on near-surface photochemical budgets, the implications for the budget of O3 in the planetary boundary layer are also discussed. In terms of daytime average, the total ROx primary production rate near the surface in Beijing is 6.6 ppbv per hour (ppbv h{sup 1}, among the highest found in urban atmospheres. The largest primary ROxmore » source in Beijing is photolysis of oxygenated volatile organic compounds (OVOCs), which produces HO2 and RO2 at 2.5 ppbv h{sup 1}1 and 1.7 ppbv h{sup 1}, respectively. Photolysis of excess HONO from an unknown heterogeneous source is the predominant primary OH source at 2.2 ppbv h{sup 1}, much larger than that of O1D+H2O (0.4 ppbv h{sup 1}). The largest ROx sink is via OH + NO2 reaction (1.6 ppbv h{sup 1}), followed by formation of RO2NO2 (1.0 ppbv h{sup 1}) and RONO2 (0.7 ppbv h{sup 1}). Due to the large aerosol surface area, aerosol uptake of HO2 appears to be another important radical sink, although the estimate of its magnitude is highly variable depending on the uptake coefficient value used. The daytime average O3 production and loss rates near the surface are 32 ppbv h{sup 1} and 6.2 ppbv h{sup 1}, respectively. Assuming NO2 to be the source of excess HONO, the NO2 to HONO transformation leads to considerable O3 loss and reduction of its lifetime. Our observation-constrained modeling analysis suggests that oxidation of VOCs (especially aromatics) and heterogeneous reactions (e.g. HONO formation and aerosol uptake HO2) play potentially critical roles in the primary radical budget and O3 formation in Beijing. One important ramification is that O3 production is neither NOx nor VOC limited, but in a transition regime where reduction

The different Li/Na ion storage mechanisms of nano Sb2O3 anchored on graphene

NASA Astrophysics Data System (ADS)

Li, Hai; Qian, Kun; Qin, Xianying; Liu, Dongqing; Shi, Ruiying; Ran, Aihua; Han, Cuiping; He, Yan-Bing; Kang, Feiyu; Li, Baohua

2018-05-01

The antimony oxide/reduced graphene oxide (Sb2O3/rGO) nanocomposites are used as anode of Li-ion and Na-ion batteries (LIBs and NIBs). However, it is unclear about Li-ion and Na-ion storage mechanism in Sb2O3/rGO nanocomposites. Herein, the conversion-alloying mechanisms of Sb2O3/rGO anodes for Na-ion and Li-ion storage are comparatively studied with a combined in-situ XRD and quasi in-situ XPS method. The distinct behaviours are monitored during (de)lithiation and (de)sodiation with respect to crystal structure and chemical composition evolution. It is evidenced that the Na-ion can be easily transported to the inner part of the Sb2O3, where the Li-ion almost cannot reach, leading to a fully transformation during sodiation. In addition, the conversion reaction product of amorphous Na2O display their better chemical stability than amorphous Li2O during electrochemical cycles, which contribute to a stable and long cycling life of NIBs. This work gain insight into the high-capacity anodes with conversation-alloying mechanism for NIBs.

Ecological Risk Assessment of Chemicals Migrated from a Recycled Plastic Product

PubMed Central

Roh, Ji-Yeon; Kim, Min-Hyuck; Kim, Woo Il; Kang, Young-Yeul; Shin, Sun Kyoung; Kim, Jong-Guk

2013-01-01

Objectives Potential environmental risks caused by chemicals that could be released from a recycled plastic product were assessed using a screening risk assessment procedure for chemicals in recycled products. Methods Plastic slope protection blocks manufactured from recycled plastics were chosen as model recycled products. Ecological risks caused by four model chemicals -di-(2-ethylhexyl) phthalate (DEHP), diisononyl phthalate (DINP), cadmium (Cd), and lead (Pb)- were assessed. Two exposure models were built for soil below the block and a hypothetic stream receiving runoff water. Based on the predicted no-effect concentrations for the selected chemicals and exposure scenarios, the allowable leaching rates from and the allowable contents in the recycled plastic blocks were also derived. Results Environmental risks posed by slope protection blocks were much higher in the soil compartment than in the hypothetic stream. The allowable concentrations in leachate were 1.0×10-4, 1.2×10-5, 9.5×10-3, and 5.3×10-3 mg/L for DEHP, DINP, Cd, and Pb, respectively. The allowable contents in the recycled products were 5.2×10-3, 6.0×10-4, 5.0×10-1, and 2.7×10-1 mg/kg for DEHP, DINP, Cd, and Pb, respectively. Conclusions A systematic ecological risk assessment approach for slope protection blocks would be useful for regulatory decisions for setting the allowable emission rates of chemical contaminants, although the method needs refinement. PMID:24303349

Ab initio chemical kinetic study on Cl + ClO and related reverse processes.

PubMed

Xu, Z F; Lin, M C

2010-11-04

The reaction of ClO with Cl and its related reverse processes have been studied theoretically by ab initio quantum chemical and statistical mechanical calculations. The geometric parameters of the reactants, products, and transition states are optimized by both UMPW1PW91 and unrestricted coupled-cluster single and double excitation (UCCSD) methods with the 6-311+G(3df) basis set. The potential energy surface has been further refined (with triple excitations, T) at the UCCSD(T)/6-311+G(3df) level of theory. The results show that Cl(2) and O ((3)P) can be produced by chlorine atom abstraction via a tight transition state, while ClOCl ((1)A(1)) and ClClO ((1)A') can be formed by barrierless association processes with exothermicities of 31.8 and 16.0 kcal/mol, respectively. In principle the O ((1)D) atom can be generated with a large endothermicity of 56.9 kcal/mol; on the other hand, its barrierless reaction with Cl(2) can readily form ClClO ((1)A'), which fragments rapidly to give ClO + Cl. The rate constants of both forward and reverse processes have been predicted at 150-2000 K by the microcanonical variational transition state theory (VTST)/Rice-Ramsperger-Kassel-Marcus (RRKM) theory. The predicted rate constants are in good agreement with available experimental data within reported errors.

Bi2O3 cocatalyst improving photocatalytic hydrogen evolution performance of TiO2

NASA Astrophysics Data System (ADS)

Xu, Difa; Hai, Yang; Zhang, Xiangchao; Zhang, Shiying; He, Rongan

2017-04-01

Photocatalytic hydrogen production using water splitting is of potential importance from the viewpoint of renewable energy development. Herein, Bi2O3-TiO2 composite photocatalysts presented as Bi-Bi2O3-anatase-rutile TiO2 multijunction were first fabricated by a simple impregnation-calcination method using Bi2O3 as H2-production cocatalysts. The obtained multijunction samples exhibit an obvious enhancement in photocatalytic H2 evolution activity in the presence of glycerol. The effect of Bi2O3 amount on H2-evolution activity of TiO2 was investigated and the optimal Bi2O3 content was found to be 0.89 mol%, achieving a H2-production rate of 920 μmol h-1, exceeding that of pure TiO2 by more than 73 times. The enhanced mechanism of photocatalytic H2-evolution activity is proposed. This study will provide new insight into the design and fabrication of TiO2-based hydrogen-production photocatalysts using low-cost Bi2O3 as cocatalyst.

A Stable, Magnetic, and Metallic Li3O4 Compound as a Discharge Product in a Li-Air Battery.

PubMed

Yang, Guochun; Wang, Yanchao; Ma, Yanming

2014-08-07

The Li-air battery with the specific energy exceeding that of a Li ion battery has been aimed as the next-generation battery. The improvement of the performance of the Li-air battery needs a full resolution of the actual discharge products. Li2O2 has been long recognized as the main discharge product, with which, however, there are obvious failures on the understanding of various experimental observations (e.g., magnetism, oxygen K-edge spectrum, etc.) on discharge products. There is a possibility of the existence of other Li-O compounds unknown thus far. Here, a hitherto unknown Li3O4 compound as a discharge product of the Li-air battery was predicted through first-principles swarm structure searching calculations. The new compound has a unique structure featuring the mixture of superoxide O2(-) and peroxide O2(2-), the first such example in the Li-O system. The existence of superoxide O2(-) creates magnetism and hole-doped metallicity. Findings of Li3O4 gave rise to direct explanations of the unresolved experimental magnetism, triple peaks of oxygen K-edge spectra, and the Raman peak at 1125 cm(-1) of the discharge products. Our work enables an opportunity for the performance of capacity, charge overpotential, and round-trip efficiency of the Li-air battery.

Impacts of elevated atmospheric CO2 and O3 on forests: phytochemistry, trophic interactions, and ecosystem dynamics.

PubMed

Lindroth, Richard L

2010-01-01

Prominent among the many factors now affecting the sustainability of forest ecosystems are anthropogenically-generated carbon dioxide (CO2) and ozone (O3). CO2 is the substrate for photosynthesis and thus can accelerate tree growth, whereas O3 is a highly reactive oxygen species and interferes with basic physiological functions. This review summarizes the impacts of CO2 and O3 on tree chemical composition and highlights the consequences thereof for trophic interactions and ecosystem dynamics. CO2 and O3 influence phytochemical composition by altering substrate availability and biochemical/physiological processes such as photosynthesis and defense signaling pathways. Growth of trees under enriched CO2 generally leads to an increase in the C/N ratio, due to a decline in foliar nitrogen and concomitant increases in carbohydrates and phenolics. Terpenoid levels generally are not affected by atmospheric CO2 concentration. O3 triggers up-regulation of antioxidant defense pathways, leading to the production of simple phenolics and flavonoids (more so in angiosperms than gymnosperms). Tannins levels generally are unaffected, while terpenoids exhibit variable responses. In combination, CO2 and O3 exert both additive and interactive effects on tree chemical composition. CO2-and O3-mediated changes in plant chemistry influence host selection, individual performance (development, growth, reproduction), and population densities of herbivores (primarily phytophagous insects) and soil invertebrates. These changes can effect shifts in the amount and temporal pattern of forest canopy damage and organic substrate deposition. Decomposition rates of leaf litter produced under elevated CO2 and O3 may or may not be altered, and can respond to both the independent and interactive effects of the pollutants. Overall, however, CO2 and O3 effects on decomposition will be influenced more by their impacts on the quantity, rather than quality, of litter produced. A prominent theme to emerge

Productivity and community structure of ectomycorrhizal fungal sporocarps under increased atmospheric CO2 and O3

Treesearch

Carrie Andrew; Erik A. Lilleskov

2009-01-01

Sporocarp production is essential for ectomycorrhizal fungal recombination and dispersal, which influences fungal community dynamics. Increasing atmospheric carbon dioxide (CO2) and ozone (O3) affect host plant carbon gain and allocation, which may in turn influence ectomycorrhizal sporocarp production if the carbon...

Low-Temperature Molten-Salt Production of Silicon Nanowires by the Electrochemical Reduction of CaSiO3.

PubMed

Dong, Yifan; Slade, Tyler; Stolt, Matthew J; Li, Linsen; Girard, Steven N; Mai, Liqiang; Jin, Song

2017-11-13

Silicon is an extremely important technological material, but its current industrial production by the carbothermic reduction of SiO 2 is energy intensive and generates CO 2 emissions. Herein, we developed a more sustainable method to produce silicon nanowires (Si NWs) in bulk quantities through the direct electrochemical reduction of CaSiO 3 , an abundant and inexpensive Si source soluble in molten salts, at a low temperature of 650 °C by using low-melting-point ternary molten salts CaCl 2 -MgCl 2 -NaCl, which still retains high CaSiO 3 solubility, and a supporting electrolyte of CaO, which facilitates the transport of O 2- anions, drastically improves the reaction kinetics, and enables the electrolysis at low temperatures. The Si nanowire product can be used as high-capacity Li-ion battery anode materials with excellent cycling performance. This environmentally friendly strategy for the practical production of Si at lower temperatures can be applied to other molten salt systems and is also promising for waste glass and coal ash recycling. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mapping Global Flows of Chemicals: From Fossil Fuel Feedstocks to Chemical Products.

PubMed

Levi, Peter G; Cullen, Jonathan M

2018-02-20

Chemical products are ubiquitous in modern society. The chemical sector is the largest industrial energy consumer and the third largest industrial emitter of carbon dioxide. The current portfolio of mitigation options for the chemical sector emphasizes upstream "supply side" solutions, whereas downstream mitigation options, such as material efficiency, are given comparatively short shrift. Key reasons for this are the scarcity of data on the sector's material flows, and the highly intertwined nature of its complex supply chains. We provide the most up to date, comprehensive and transparent data set available publicly, on virgin production routes in the chemical sector: from fossil fuel feedstocks to chemical products. We map global mass flows for the year 2013 through a complex network of transformation processes, and by taking account of secondary reactants and by-products, we maintain a full mass balance throughout. The resulting data set partially addresses the dearth of publicly available information on the chemical sector's supply chain, and can be used to prioritise downstream mitigation options.

BaTiO3-based piezoelectrics: Fundamentals, current status, and perspectives

NASA Astrophysics Data System (ADS)

Acosta, M.; Novak, N.; Rojas, V.; Patel, S.; Vaish, R.; Koruza, J.; Rossetti, G. A.; Rödel, J.

2017-12-01

We present a critical review that encompasses the fundamentals and state-of-the-art knowledge of barium titanate-based piezoelectrics. First, the essential crystallography, thermodynamic relations, and concepts necessary to understand piezoelectricity and ferroelectricity in barium titanate are discussed. Strategies to optimize piezoelectric properties through microstructure control and chemical modification are also introduced. Thereafter, we systematically review the synthesis, microstructure, and phase diagrams of barium titanate-based piezoelectrics and provide a detailed compilation of their functional and mechanical properties. The most salient materials treated include the (Ba,Ca)(Zr,Ti)O3, (Ba,Ca)(Sn,Ti)O3, and (Ba,Ca)(Hf,Ti)O3 solid solution systems. The technological relevance of barium titanate-based piezoelectrics is also discussed and some potential market indicators are outlined. Finally, perspectives on productive lines of future research and promising areas for the applications of these materials are presented.

Investigation of N2O Production from 266 and 532 nm Laser Flash Photolysis of O3/N2/O2 Mixtures

NASA Technical Reports Server (NTRS)

Estupinan, E. G.; Nicovich, J. M.; Li, J.; Cunnold, D. M.; Wine, P. H.

2002-01-01

Tunable diode laser absorption spectroscopy has been employed to measure the amount of N2O produced from laser flash photolysis of O3/N2/O2 mixtures at 266 and 532 nm. In the 532 nm photolysis experiments very little N2O is observed, thus allowing an upper limit yield of 7 x 10(exp -8) to be established for the process O3 + N2 yield N2O + O2, where O3 is nascent O3 that is newly formed via O(3P(sub J)) + O2 recombination (with vibrational excitation near the dissociation energy of O3). The measured upper limit yield is a factor of approx. 600 smaller than a previous literature value and is approximately a factor of 10 below the threshold for atmospheric importance. In the 266 nm photolysis experiments, significant N2O production is observed and the N2O quantum yield is found to increase linearly with pressure over the range 100 - 900 Torr in air bath gas. The source of N2O in the 266 nm photolysis experiments is believed to be the addition reaction O(1D(sub 2)) + N2 + M yields (k(sub sigma)) N2O + M, although reaction of (very short-lived) electronically excited O3 with N2 cannot be ruled out by the available data. Assuming that all observed N2O comes from the O(1D(sub 2)) + N2 + M reaction, the following expression describes the temperature dependence of k(sub sigma) (in its third-order low-pressure limit) that is consistent with the N2O yield data: k(sub sigma) = (2.8 +/- 0.1) x 10(exp -36)(T/300)(sup -(0-88+0.36)) cm(sup 6) molecule(sup -2)/s, where the uncertainties are 2(sigma) and represent precision only. The accuracy of the reported rate coefficients at the 95% confidence level is estimated to be 30 - 40% depending on the temperature. Model calculations suggest that gas phase processes initiated by ozone absorption of a UV photon represent about 1.4% of the currently estimated global source strength of atmospheric N2O. However, these processes could account for a significant fraction of the oxygen mass-independent enrichment observed in atmospheric N2O, and

Hybrid quantum chemical studies for the methanol formation reaction assisted by the proton transfer mechanism in supercritical water: CH3Cl+nH2O-->CH3OH+HCl+(n-1)H2O

NASA Astrophysics Data System (ADS)

Hori, T.; Takahashi, H.; Nitta, T.

2003-10-01

The proton transfer along the chain of hydrogen bonds is involved in many chemical reactions in aqueous solution and known to play a decisive role. We have performed the hybrid quantum chemical simulations for the methanol formation reaction catalyzed by the proton transfer mechanism [CH3Cl+nH2O→CH3OH+HCl+(n-1)H2O, n=3] in supercritical water (SCW) to investigate the role of water solvent on the reaction. In the simulation, the electronic state of the chemically active solutes (CH3Cl+3H2O) has been determined quantum mechanically, while the static water solvent has been represented by a classical model. The activation free energy for the water-catalytic reaction in SCW has been found to be 9.6 kcal/mol, which is much lower than that in the gas phase (29.2 kcal/mol). The fractional charge analysis has revealed that the notable charge separation in the solute complex takes place at the transition state (TS) and the resulting huge dipole gives rise to the considerable stabilization of the TS as compared to the reactant. It has been shown that the reaction assisted by the proton transfer mechanism is energetically much favored than the ionic SN2 reaction (CH3Cl+OH-→CH3OH+Cl-, 18.8 kcal/mol). The present calculations suggest that the proton migrations through the chain of hydrogen bonds can be regarded as a probable candidate responsible for the anomalous reactivities observed in SCW.

Advancing Consumer Product Composition and Chemical ...

EPA Pesticide Factsheets

This presentation describes EPA efforts to collect, model, and measure publically available consumer product data for use in exposure assessment. The development of the ORD Chemicals and Products database will be described, as will machine-learning based models for predicting chemical function. Finally, the talk describes new mass spectrometry-based methods for measuring chemicals in formulation and articles. This presentation is an invited talk to the ICCA-LRI workshop "Fit-For-Purpose Exposure Assessments For Risk-Based Decision Making". The talk will share EPA efforts to characterize the components of consumer products for use in exposure assessment with the international exposure science community.

Synthesis H-Zeolite catalyst by impregnation KI/KIO3 and performance test catalyst for biodiesel production

NASA Astrophysics Data System (ADS)

Widayat, W.; Rizky Wicaksono, Adit; Hakim Firdaus, Lukman; Okvitarini, Ndaru

2016-02-01

The objective of this research is to produce H-catalyst catalyst that was impregnated with KI/KIO3. The catalyst was analyzed about surface area, X-Ray Diffraction (XRD) and performance test of catalyst for biodiesel production. An H-Zeolite catalyst was synthesized from natural zeolite with chemical treatment processing, impregnation KI/KIO3 and physical treatment. The results shows that the surface area of the catalyst by 27.236 m2/g at a concentration of 5% KI. XRD analysis shows peak 2-θ at 23.627o indicating that KI was impregnated on H-zeolite catalyst. The catalyst was tested in production of biodiesel using palm oil with conventional methods for 3 hour at temperature of 70-80 oC. The result for conversion Fatty Acid Methyl Ester (FAME) reached maximum value on 87.91% under production process using catalyst 5% KIO3-H zeolite.

[Control on products of NDMA degradation by UV/O3].

PubMed

Xu, Bing-bing; Chen, Zhong-lin; Qi, Fei; Yang, Lei; Huang, Lu-xi

2008-12-01

Comparison experiments of two advanced oxidation processes, UV/O3 and UV/H2O2, were carried out to evaluate their degradation effect of N-nitrosodimethylamine (NDMA) and controlling effect of dimethylamine (DMA) formation. The results showed that UV/H2O2 could enhance NDMA degradation, but could not control on the formation of DMA. UV/O3 was not only effective for NDMA degradation, but also was good at controlling on DMA formation. Furthermore, factors affecting the formation of DMA during degradation of NDMA by UV/O3 were studied. The formation of DMA decreased with O3 dosage increasing and DMA was 0.98 mg x L(-1) with 7.7 mg x L(-1) NDMA and 6.64 mg x L(-1) O3 dose. Solution pH had obvious effect on controlling of DMA formation during degradation of NDMA by UV/O3 . The formation of DMA lightly increased with pH increasing from acid to neutral but dramatically decreased in basic aqueous solution. The formation of DMA was only 0.3 mg x L(-1) when the initial concentration of NDMA was 7.7 mg x L(-1) under pH = 11.0 condition. UV/O3 had better controlling of DMA formation with lesser initial concentration of NDMA.

Stabilization of Hydrogen Production via Methanol Steam Reforming in Microreactor by Al2O3 Nano-Film Enhanced Catalyst Adhesion.

PubMed

Jeong, Heondo; Na, Jeong-Geol; Jang, Min Su; Ko, Chang Hyun

2016-05-01

In hydrogen production by methanol steam reforming reaction with microchannel reactor, Al2O3 thin film formed by atomic layer deposition (ALD) was introduced on the surface of microchannel reactor prior to the coating of catalyst particles. Methanol conversion rate and hydrogen production rate, increased in the presence of Al2O3 thin film. Over-view and cross-sectional scanning electron microscopy study showed that the adhesion between catalyst particles and the surface of microchannel reactor enhanced due to the presence of Al2O3 thin film. The improvement of hydrogen production rate inside the channels of microreactor mainly came from the stable fixation of catalyst particles on the surface of microchannels.

Chemical failure modes of AlQ3-based OLEDs: AlQ3 hydrolysis.

PubMed

Knox, John E; Halls, Mathew D; Hratchian, Hrant P; Schlegel, H Bernhard

2006-03-28

Tris(8-hydroxyquinoline)aluminum(III), AlQ3, is used in organic light-emitting diodes (OLEDs) as an electron-transport material and emitting layer. The reaction of AlQ3 with trace H2O has been implicated as a major failure pathway for AlQ3-based OLEDs. Hybrid density functional calculations have been carried out to characterize the hydrolysis of AlQ3. The thermochemical and atomistic details for this important reaction are reported for both the neutral and oxidized AlQ3/AlQ3+ systems. In support of experimental conclusions, the neutral hydrolysis reaction pathway is found to be a thermally activated process, having a classical barrier height of 24.2 kcal mol(-1). First-principles infrared and electronic absorption spectra are compared to further characterize AlQ3 and the hydrolysis pathway product, AlQ2OH. The activation energy for the cationic AlQ3 hydrolysis pathway is found to be 8.5 kcal mol(-1) lower than for the neutral reaction, which is significant since it suggests a role for charge imbalance in promoting chemical failure modes in OLED devices.

Biorefineries for the production of top building block chemicals and their derivatives.

PubMed

Choi, Sol; Song, Chan Woo; Shin, Jae Ho; Lee, Sang Yup

2015-03-01

Due to the growing concerns on the climate change and sustainability on petrochemical resources, DOE selected and announced the bio-based top 12 building blocks and discussed the needs for developing biorefinery technologies to replace the current petroleum based industry in 2004. Over the last 10 years after its announcement, many studies have been performed for the development of efficient technologies for the bio-based production of these chemicals and derivatives. Now, ten chemicals among these top 12 chemicals, excluding the l-aspartic acid and 3-hydroxybutyrolactone, have already been commercialized or are close to commercialization. In this paper, we review the current status of biorefinery development for the production of these platform chemicals and their derivatives. In addition, current technological advances on industrial strain development for the production of platform chemicals using micro-organisms will be covered in detail with case studies on succinic acid and 3-hydroxypropionic acid as examples. Copyright © 2015 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

Measurements of HNO3 and N2O5 using ion drift-chemical ionization mass spectrometry during the MILAGRO/MCMA-2006 campaign

NASA Astrophysics Data System (ADS)

Zheng, J.; Zhang, R.; Fortner, E. C.; Volkamer, R. M.; Molina, L.; Aiken, A. C.; Jimenez, J. L.; Gaeggeler, K.; Dommen, J.; Dusanter, S.; Stevens, P. S.; Tie, X.

2008-11-01

An ion drift-chemical ionization mass spectrometer (ID-CIMS) was deployed in Mexico City between 7 and 31 March to measure gas-phase nitric acid (HNO3) and dinitrogen pentoxide (N2O5 during the Mexico City Metropolitan Area (MCMA)-2006 field campaign. The observation site was located at the Instituto Mexicano del Petróleo in the northern part of Mexico City urban area with major emissions of pollutants from residential, vehicular and industrial sources. Diurnally, HNO3 was less than 200 parts per trillion (ppt) during the night and early morning. The concentration of HNO3 increased steadily from around 09:00 a.m. central standard time (CST), reached a peak value of 0.5 to 3 parts per billion (ppb) in the early afternoon, and then declined sharply to less than half of the peak value near 05:00 p.m. CST. An inter-comparison between the ID-CIMS and an ion chromatograph/mass spectrometer (ICMS) showed a good agreement between the two HNO3 measurements (R2=0.75). The HNO3 mixing ratio was found to anti-correlate with submicron-sized aerosol nitrate, suggesting that the gas-particle partitioning process was a major factor in determining the gaseous HNO3 concentration. Losses by irreversible reactions with mineral dust and via dry deposition also could be important at this site. Most of the times during the MCMA 2006 field campaign, N2O5 was found to be below the detection limit (about 30 ppt for a 10 s integration time) of the ID-CIMS, because of high NO mixing ratio at the surface (>100 ppb) during the night. An exception occurred on 26 March 2006, when about 40 ppt N2O5 was observed during the late afternoon and early evening hours under cloudy conditions before the build-up of NO at the surface site. The results revealed that during the MCMA-2006 field campaign HNO3 was primarily produced from the reaction of OH with NO2 and regulated by gas/particle transfer and dry deposition. The production of HNO3 from N2O5 hydrolysis during the nighttime was small because of

Atmospheric Chemistry of (CF3)2CHOCH3, (CF3)2CHOCHO, and CF3C(O)OCH3.

PubMed

Østerstrøm, Freja From; Wallington, Timothy J; Sulbaek Andersen, Mads P; Nielsen, Ole John

2015-10-22

Smog chambers with in situ FTIR detection were used to measure rate coefficients in 700 Torr of air and 296 ± 2 K of: k(Cl+(CF3)2CHOCH3) = (5.41 ± 1.63) × 10(-12), k(Cl+(CF3)2CHOCHO) = (9.44 ± 1.81) × 10(-15), k(Cl+CF3C(O)OCH3) = (6.28 ± 0.98) × 10(-14), k(OH+(CF3)2CHOCH3) = (1.86 ± 0.41) × 10(-13), and k(OH+(CF3)2CHOCHO) = (2.08 ± 0.63) × 10(-14) cm(3) molecule(-1) s(-1). The Cl atom initiated oxidation of (CF3)2CHOCH3 gives (CF3)2CHOCHO in a yield indistinguishable from 100%. The OH radical initiated oxidation of (CF3)2CHOCH3 gives the following products (molar yields): (CF3)2CHOCHO (76 ± 8)%, CF3C(O)OCH3 (16 ± 2)%, CF3C(O)CF3 (4 ± 1)%, and C(O)F2 (45 ± 5)%. The primary oxidation product (CF3)2CHOCHO reacts with Cl atoms to give secondary products (molar yields): CF3C(O)CF3 (67 ± 7)%, CF3C(O)OCHO (28 ± 3)%, and C(O)F2 (118 ± 12)%. CF3C(O)OCH3 reacts with Cl atoms to give: CF3C(O)OCHO (80 ± 8)% and C(O)F2 (6 ± 1)%. Atmospheric lifetimes of (CF3)2CHOCH3, (CF3)2CHOCHO, and CF3C(O)OCH3 were estimated to be 62 days, 1.5 years, and 220 days, respectively. The 100-year global warming potentials (GWPs) for (CF3)2CHOCH3, (CF3)2CHOCHO, and CF3C(O)OCH3 are estimated to be 6, 121, and 46, respectively. A comprehensive description of the atmospheric fate of (CF3)2CHOCH3 is presented.

Development of a headspace GC/MS analysis for carbonyl compounds (aldehydes and ketones) in household products after derivatization with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine.

PubMed

Sugaya, Naeko; Sakurai, Katsumi; Nakagawa, Tomoo; Onda, Nobuhiko; Onodera, Sukeo; Morita, Masatoshi; Tezuka, Masakatsu

2004-05-01

Carbonyl compounds (aldehydes and ketones) are suspected to be among the chemical compounds responsible for Sick Building Syndrome and Multiple Chemical Sensitivities. A headspace gas chromatography/mass spectrometry (GC/MS) analysis for these compounds was developed using derivatization of the compounds into volatile derivatives with o-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine (PFBOA). For GC/MS detection, two ionization modes including electron impact ionization (EI) and negative chemical ionization (NCI) were compared. The NCI mode seemed to be better because of its higher selectivity and sensitivity. This headspace GC/MS (NCI mode) was employed as analysis for aldehydes and ketones in materials (fiber products, adhesives, and printed materials). Formaldehyde was detected in the range of N.D. (not detected) to 39 microg/g; acetaldehyde, N.D. to 4.1 microg/g; propionaldehyde, N.D. to 1.0 microg/g; n-butyraldehyde, N.D. to 0.10 microg/g; and acetone, N.D. to 3.1 microg/g in the samples analyzed.

SnO2, IrO2, Ta2O5, Bi2O3, and TiO2 nanoparticle anodes: electrochemical oxidation coupled with the cathodic reduction of water to yield molecular H2

NASA Astrophysics Data System (ADS)

Choi, Jina; Qu, Yan; Hoffmann, Michael R.

2012-08-01

In recent years, the search for environmentally friendly alternative energy sources with reduced carbon footprints has increased. The coupling of photovoltaic power sources with advanced electrolysis systems for hydrogen production via water splitting using organic contaminants as sacrificial electron donors has been considered to a be viable alternative. In this report, we demonstrated the feasibility of a scaled-up rooftop prototype of the proposed hybrid photovoltaic-electrolysis system, which utilizes semiconductor nanoparticles coated on to metal substrates as electrodes for the generation of hydrogen coupled with the oxidation of wastewater. Application of an anodic bias of >2.0 V to bismuth-doped TiO2 (BiO x -TiO2) on Ti metal anodes with a sequential under-coatings of nanoparticulate SnO2, IrO2, Ta2O5, and Bi2O3 results in the electrochemical degradation of a variety of organic chemical contaminants in water (i.e., rhodamine B (Rh.B), methylene blue (MB), salicylic acid, triclosan, and phenol) and actual wastewater from a chemical manufacturing plant, while at the same time, molecular hydrogen is produced at stainless steel (SS) cathodes. The kinetics of the anodic substrates oxidation is investigated as a function of the cell current ( I cell), substrate concentration, and background electrolyte composition (e.g., NaCl, Na2SO4, or seawater). Average current efficiencies were found to be in the range of 4-22 %, while the cathodic current and energy efficiencies for hydrogen production were found to be in the range of 50-70 % and 20-40 %, respectively.

Data on PKO biodiesel production using CaO catalyst from Turkey bones.

PubMed

Ayoola, A A; Fayomi, O S I; Usoro, I F

2018-08-01

In this research paper the production of biodiesel from palm kernel oil (PKO) using CaO obtained from waste turkey bones (WTB) and analytical grade calcium oxide was investigated. Treated WTB was reduced to fine particulate size of <150 µm and then calcinated at 800 °C for 3 h to increase its catalytic activity by its conversion from Calcium phosphate hydroxide (Ca 10 P 6 O 26 H 2 ) to CaO. X-ray diffraction (XRD) and X-ray fluorescent (XRF) analysis of the analytical grade CaO, uncalcined and calcined WTB were carried out to establish their elemental chemical composition. The transesterification reaction between the triglyceride of palm kernel oil (PKO) and methanol was carried out at a constant agitation speed of 600 rpm and temperature of 65 °C, with varied methanol to oil molar ratio (8-14), catalyst concentration (1-7 wt/wt%) and the reaction time (1-3 h). Minitab 17 software (using response surface method) was employed for the design of experiment and statistical analysis required in the transesterification process of biodiesel production. The qualities of the biodiesel produced were assessed and the results obtained showed conformity of the biodiesel produced to the ASTM standard for biodiesel.

Preparation and Scintillating Properties of Sol-Gel Eu3+, Tb3+ Co-Doped Lu2O3 Nanopowders

PubMed Central

de Jesús Morales Ramírez, Ángel; Murillo, Antonieta García; de Jesús Carrillo Romo, Felipe; Hernández, Margarita García; Palmerin, Joel Moreno; Guerrero, Rosario Ruiz

2011-01-01

Nanocrystalline Eu3+, Tb3+ co-doped Lu2O3 powders with a maximum size of 25.5 nm were prepared by the sol-gel process, using lutetium, europium and terbium nitrates as precursors, and ethanol as a solvent. Differential thermal analysis (DTA) and infrared spectroscopy (IR) were used to study the chemical changes during the xerogel annealing. After the sol evaporation at 100 °C, the formed gel was annealed from 300 to 900 °C for 30 min under a rich O2 atmosphere, and the yielded product was analyzed by X-ray diffraction (XRD) to characterize the microstructural behavior and confirm the crystalline structure. The results showed that Lu2O3 nanopowders start to crystallize at 400 °C and that the crystallite size increases along with the annealing temperature. A transmission electron microscopy (TEM) study of samples annealed at 700 and 900 °C was carried out in order to analyze the microstructure, as well as the size, of crystallites. Finally, in regard to scintillating properties, Eu3+ dopant (5 mol%), Tb3+ codoped Lu2O3 exhibited a typical red emission at 611 nm (D°→7F2), furthermore, the effect of Tb3+ molar content (0.01, 0.015 and 0.02% mol) on the Eu3+ radioluminiscence was analyzed and it was found that the higher emission intensity corresponds to the lower Tb3+ content. PMID:22016655

Single liquid source plasma-enhanced metalorganic chemical vapor deposition of high-quality YBa2Cu3O(7-x) thin films

NASA Technical Reports Server (NTRS)

Zhang, Jiming; Gardiner, Robin A.; Kirlin, Peter S.; Boerstler, Robert W.; Steinbeck, John

1992-01-01

High quality YBa2Cu3O(7-x) films were grown in-situ on LaAlO3 (100) by a novel single liquid source plasma-enhanced metalorganic chemical vapor deposition process. The metalorganic complexes M(thd) (sub n), (thd = 2,2,6,6-tetramethyl-3,5-heptanedionate; M = Y, Ba, Cu) were dissolved in an organic solution and injected into a vaporizer immediately upstream of the reactor inlet. The single liquid source technique dramatically simplifies current CVD processing and can significantly improve the process reproducibility. X-ray diffraction measurements indicated that single phase, highly c-axis oriented YBa2Cu3O(7-x) was formed in-situ at substrate temperature 680 C. The as-deposited films exhibited a mirror-like surface, had transition temperature T(sub cO) approximately equal to 89 K, Delta T(sub c) less than 1 K, and Jc (77 K) = 10(exp 6) A/sq cm.

Charge transfer mechanism for the formation of metallic states at the KTaO3/SrTiO3 interface

NASA Astrophysics Data System (ADS)

Nazir, S.; Singh, N.; Schwingenschlögl, U.

2011-03-01

The electronic and optical properties of the KTaO3/SrTiO3 heterointerface are analyzed by the full-potential linearized augmented plane-wave approach of density functional theory. Optimization of the atomic positions points at subordinate changes in the crystal structure and chemical bonding near the interface, which is due to a minimal lattice mismatch. The creation of metallic interface states thus is not affected by structural relaxation but can be explained by charge transfer between transition metal and oxygen atoms. It is to be expected that a charge transfer is likewise important for related interfaces such as LaAlO3/SrTiO3. The KTaO3/SrTiO3 system is ideal for disentangling the complex behavior of metallic interface states, since almost no structural relaxation takes place.

Thermal and chemical decomposition of di(pyrazine)silver(II) peroxydisulfate and unusual crystal structure of a Ag(I) by-product.

PubMed

Leszczyński, Piotr J; Budzianowski, Armand; Dobrzycki, Lukasz; Cyrański, Michał K; Derzsi, Mariana; Grochala, Wojciech

2012-01-14

High purity samples of a [Ag(pyrazine)(2)]S(2)O(8) complex were obtained using modified synthetic pathways. Di(pyrazine)silver(II) peroxydisulfate is sensitive to moisture forming [Ag(pyrazine)(2)](S(2)O(8))(H(2)O) hydrate which degrades over time yielding HSO(4)(-) derivatives and releasing oxygen. One polymorphic form of pyrazinium hydrogensulfate, β-(pyrazineH(+))(HSO(4)(-)), is found among the products of chemical decomposition together with unique [Ag(i)(pyrazine)](5)(H(2)O)(2)(HSO(4))(2)[H(SO(4))(2)]. Chemical degradation of [Ag(pyrazine)(2)]S(2)O(8) in the presence of trace amounts of moisture can explain the very low yield of wet synthesis (11-15%). Attempts have failed to obtain a mixed valence Ag(II)/Ag(I) pyrazine complex via partial chemical reduction of the [Ag(pyrazine)(2)]S(2)O(8) precursor with a variety of inorganic and organic reducing agents, or via controlled thermal decomposition. Thermal degradation of [Ag(pyrazine)(2)]S(2)O(8) containing occluded water proceeds at T > 90 °C via evolution of O(2); simultaneous release of pyrazine and SO(3) is observed during the next stages of thermal decomposition (120-285 °C), while Ag(2)SO(4) and Ag are obtained upon heating to 400-450 °C.

Chemical Waste and Allied Products.

PubMed

Hung, Yung-Tse; Aziz, Hamidi Abdul; Ramli, Siti Fatihah; Yeh, Ruth Yu-Li; Liu, Lian-Huey; Huhnke, Christopher Robert

2016-10-01

This review of literature published in 2015 focuses on waste related to chemical and allied products. The topics cover the waste management, physicochemical treatment, aerobic granular, aerobic waste treatment, anaerobic granular, anaerobic waste treatment, chemical waste, chemical wastewater, fertilizer waste, fertilizer wastewater, pesticide wastewater, pharmaceutical wastewater, ozonation. cosmetics waste, groundwater remediation, nutrient removal, nitrification denitrification, membrane biological reactor, and pesticide waste.

Stabilization/solidification of radioactive salt waste by using xSiO2-yAl2O3-zP2O5 (SAP) material at molten salt state.

PubMed

Park, Hwan-Seo; Kim, In-Tae; Cho, Yong-Zun; Eun, Hee-Chul; Lee, Han-Soo

2008-12-15

The molten salt waste from the pyroprocess is one of the problematic wastes to directly apply a conventional process such as vitrification or ceramization. This study suggested a novel method using a reactive material for metal chlorides at a molten temperature of salt waste, and then converting them into manageable product at a high temperature. The inorganic composite, SAP (SiO2-Al2O3-P2O5), synthesized by a conventional sol-gel process has three or four distinctive domains that are bonded sequentially, Si-O-Si-O-A-O-P-O-P. The P-rich phase in the SAP composite is unstable for producing a series of reactive sites when in contact with a molten LiCl salt. After the reaction, metal aluminosilicate, metal aluminophosphate, metal phosphates and gaseous chlorines are generated. From this process, the volatile salt waste is stabilized and it is possible to apply a high temperature process. The reaction products were fabricated successfully by using a borosilicate glass with an arbitrary composition as a chemical binder. There was a low possibility for the valorization of radionuclides up to 1200 degrees C, based on the result of the thermo gravimetric analysis. The Cs and Sr leach rates by the PCT-A method were about 1 x 10(-3) g/(m2 day). For the final disposal of the problematic salt waste, this approach suggested the design concept of an effective stabilizer for metal chlorides and revealed the chemical route to the fabrication of monolithic wasteform by using a composite as an example. Using this method, we could obtain a higher disposal efficiency and lower waste volume, compared with the present immobilization methods.

CH 4/NH 3/H 2O spark tholin: Chemical analysis and interaction with Jovian aqueous clouds

NASA Astrophysics Data System (ADS)

McDonald, Gene D.; Khare, Bishun N.; Reid Thompson, W.; Sagan, Carl

1991-12-01

The organic solid (tholin) produced by spark discharge in a CH 4 + NH 3 + H 2O atmosphere is investigated, along with the separable components of its water-soluble fraction. The chemistry of this material serves as a provisional model for the interaction of Jovian organic heteropolymers with the deep aqueous clouds of Jupiter. Intact (unhydrolyzed) tholin is resolved into four chemically distinct fractions by high-pressure liquid chromatography (HPLC). Gel filtration chromatography reveals abundant components at molecular weights ⋍600-700 and 200-300 Da. Gas chromatography/mass spectrometry of derivatized hydrolysis products of unfractionated tholin shows about 10% by mass protein and nonprotein amino acids, chiefly glycine, alanine, aspartic acid, β-alanine, and β-aminobutyric acid, and 12% by mass other organic acids and hydroxy acids. The stereospecificity of alanine is investigated and shown to be racemic. The four principal HPLC fractions yield distinctly different proportions of amino acids. Chemical tests show that small peptides or organic molecules containing multiple amino acid precursors are a possibility in the intact tholins, but substantial quantities of large peptides are not indicated. Candidate 700-Da molecules have a central unsaturated, hydrocarbon- and nitrile-rich core, linked by acid-labile (ester or amide) bonds to amino acid and carboxylic acid side groups. The core is probably not HCN "polymer." The concentration of amino acids from tholin hydrolysis in the lower aqueous clouds of Jupiter, about 0.1 μ M, is enough to maintain small populations of terrestrial microorganisms even if the amino acids must serve as the sole carbon source.

Nd-doped Bi2O3 nanocomposites: simple synthesis and improved photocatalytic activity for hydrogen production under visible light

NASA Astrophysics Data System (ADS)

Al-Namshah, Khadijah S.; Mohamed, Reda M.

2018-04-01

Bi2O3 has 2.4 eV band gap energy, which means it absorb in visible region. Though the photocatalytic activity of Bi2O3 is extremely little due to rapid rate of photogenerated electron-hole recombination. To face the economical and practical needs, the photocatalytic efficiency of Bi2O3 should be upgraded. In this paper, this was achieved by addition of neodymium to Bi2O3 nanosheets and Nd/Bi2O3 nanocomposites were prepared by a easy process at room temperature using a surfactant of Pluronic F127. The Bi2O3 nanosheets and Nd/Bi2O3 nanocomposites were investigated by many tools. The photocatalytic activity of Nd/Bi2O3 samples is better than Bi2O3 due to reduced band gap and reduced electron-hole recombination of Bi2O3 with addition of neodymium. In addition, Nd/Bi2O3 nanocomposites exhibit photocatalytic stability for hydrogen production which enables it to be reused on other occasions also.

Stratospheric O3 changes during 2001-2010: the small role of solar flux variations in a chemical transport model

NASA Astrophysics Data System (ADS)

Dhomse, S. S.; Chipperfield, M. P.; Feng, W.; Ball, W. T.; Unruh, Y. C.; Haigh, J. D.; Krivova, N. A.; Solanki, S. K.; Smith, A. K.

2013-10-01

Solar spectral fluxes (or irradiance) measured by the SOlar Radiation and Climate Experiment (SORCE) show different variability at ultraviolet (UV) wavelengths compared to other irradiance measurements and models (e.g. NRL-SSI, SATIRE-S). Some modelling studies have suggested that stratospheric/lower mesospheric O3 changes during solar cycle 23 (1996-2008) can only be reproduced if SORCE solar fluxes are used. We have used a 3-D chemical transport model (CTM), forced by meteorology from the European Centre for Medium-Range Weather Forecasts (ECMWF), to simulate middle atmospheric O3 using three different solar flux data sets (SORCE, NRL-SSI and SATIRE-S). Simulated O3 changes are compared with Microwave Limb Sounder (MLS) and Sounding of the Atmosphere using Broadband Emission Radiometry (SABER) satellite data. Modelled O3 anomalies from all solar flux data sets show good agreement with the observations, despite the different flux variations. The off-line CTM reproduces these changes through dynamical information contained in the analyses. A notable feature during this period is a robust positive solar signal in the tropical middle stratosphere, which is due to realistic dynamical changes in our simulations. Ozone changes in the lower mesosphere cannot be used to discriminate between solar flux data sets due to large uncertainties and the short time span of the observations. Overall this study suggests that, in a CTM, the UV variations detected by SORCE are not necessary to reproduce observed stratospheric O3 changes during 2001-2010.

Effect of operational and water quality parameters on conventional ozonation and the advanced oxidation process O3/H2O2: Kinetics of micropollutant abatement, transformation product and bromate formation in a surface water.

PubMed

Bourgin, Marc; Borowska, Ewa; Helbing, Jakob; Hollender, Juliane; Kaiser, Hans-Peter; Kienle, Cornelia; McArdell, Christa S; Simon, Eszter; von Gunten, Urs

2017-10-01

The efficiency of ozone-based processes under various conditions was studied for the treatment of a surface water (Lake Zürich water, Switzerland) spiked with 19 micropollutants (pharmaceuticals, pesticides, industrial chemical, X-ray contrast medium, sweetener) each at 1 μg L -1 . Two pilot-scale ozonation reactors (4-5 m 3  h -1 ), a 4-chamber reactor and a tubular reactor, were investigated by either conventional ozonation and/or the advanced oxidation process (AOP) O 3 /H 2 O 2 . The effects of selected operational parameters, such as ozone dose (0.5-3 mg L -1 ) and H 2 O 2 dose (O 3 :H 2 O 2  = 1:3-3:1 (mass ratio)), and selected water quality parameters, such as pH (6.5-8.5) and initial bromide concentration (15-200 μg L -1 ), on micropollutant abatement and bromate formation were investigated. Under the studied conditions, compounds with high second-order rate constants k O3 >10 4  M -1  s -1 for their reaction with ozone were well abated (>90%) even for the lowest ozone dose of 0.5 mg L -1 . Conversely, the abatement efficiency of sucralose, which only reacts with hydroxyl radicals (OH), varied between 19 and 90%. Generally, the abatement efficiency increased with higher ozone doses and higher pH and lower bromide concentrations. H 2 O 2 addition accelerated the ozone conversion to OH, which enables a faster abatement of ozone-resistant micropollutants. Interestingly, the abatement of micropollutants decreased with higher bromide concentrations during conventional ozonation due to competitive ozone-consuming reactions, except for lamotrigine, due to the suspected reaction of HOBr/OBr - with the primary amine moieties. In addition to the abatement of micropollutants, the evolution of the two main transformation products (TPs) of hydrochlorothiazide (HCTZ) and tramadol (TRA), chlorothiazide (CTZ) and tramadol N-oxide (TRA-NOX), respectively, was assessed by chemical analysis and kinetic modeling. Both selected TPs were quickly formed initially

Iso-oriented monolayer α-MoO 3 (010) films epitaxially grown on SrTiO 3 (001)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Du, Yingge; Li, Guoqiang; Peterson, Erik W.

The ability to synthesis well-ordered two-dimensional materials under ultra-high vacuum and directly characterize them by other techniques in-situ can greatly advance our current understanding on their physical and chemical properties. In this paper, we demonstrate that iso-oriented α-MoO3 films with as low as single monolayer thickness can be reproducibly grown on SrTiO3(001) substrates by molecular beam epitaxy ( (010)MoO3 || (001)STO, [100]MoO3 || [100]STO or [010]STO) through a self-limiting process. While one in-plane lattice parameter of the MoO3 is very close to that of the SrTiO3 (aMoO3 = 3.96 Å, aSTO = 3.905 Å), the lattice mismatch along other directionmore » is large (~5%, cMoO3 = 3.70 Å), which leads to relaxation as clearly observed from the splitting of streaks in reflection high-energy electron diffraction (RHEED) patterns. A narrow range in the growth temperature is found to be optimal for the growth of monolayer α-MoO3 films. Increasing deposition time will not lead to further increase in thickness, which is explained by a balance between deposition and thermal desorption due to the weak van der Waals force between α-MoO3 layers. Lowering growth temperature after the initial iso-oriented α-MoO3 monolayer leads to thicker α-MoO3(010) films with excellent crystallinity.« less

Al2O3 Passivation Effect in HfO2·Al2O3 Laminate Structures Grown on InP Substrates.

PubMed

Kang, Hang-Kyu; Kang, Yu-Seon; Kim, Dae-Kyoung; Baik, Min; Song, Jin-Dong; An, Youngseo; Kim, Hyoungsub; Cho, Mann-Ho

2017-05-24

The passivation effect of an Al 2 O 3 layer on the electrical properties was investigated in HfO 2 -Al 2 O 3 laminate structures grown on indium phosphide (InP) substrate by atomic-layer deposition. The chemical state obtained using high-resolution X-ray photoelectron spectroscopy showed that interfacial reactions were dependent on the presence of the Al 2 O 3 passivation layer and its sequence in the HfO 2 -Al 2 O 3 laminate structures. Because of the interfacial reaction, the Al 2 O 3 /HfO 2 /Al 2 O 3 structure showed the best electrical characteristics. The top Al 2 O 3 layer suppressed the interdiffusion of oxidizing species into the HfO 2 films, whereas the bottom Al 2 O 3 layer blocked the outdiffusion of In and P atoms. As a result, the formation of In-O bonds was more effectively suppressed in the Al 2 O 3 /HfO 2 /Al 2 O 3 /InP structure than that in the HfO 2 -on-InP system. Moreover, conductance data revealed that the Al 2 O 3 layer on InP reduces the midgap traps to 2.6 × 10 12 eV -1 cm -2 (compared to that of HfO 2 /InP, that is, 5.4 × 10 12 eV -1 cm -2 ). The suppression of gap states caused by the outdiffusion of In atoms significantly controls the degradation of capacitors caused by leakage current through the stacked oxide layers.

Gd{sup 3+} incorporated ZnO nanoparticles: A versatile material

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Surender, E-mail: surender40@gmail.com; Sahare, P.D.

Graphical abstract: - Highlights: • Chemically synthesized Gd{sup 3+} doped ZnO nanoparticles. • The broad visible emission of the ZnO is dependent on the surface defects and can be tailored by Gd{sup 3+} doing. • PL and magnetic properties are modified by Gd{sup 3+} doping. • Photocatalysis experiment reveals that the ZnO: Gd{sup 3+} degrades the Rh B dye faster than the undoped ZnO. - Abstract: Gd{sup 3+} doped ZnO nanoparticles are synthesized by wet chemical route method and investigated through structural, optical, magnetic and photocatalytic properties. Transmission Electron Microscopy technique has been performed on undoped and Gd{sup 3+} dopedmore » ZnO nanoparticles. X-ray diffraction, X-ray photoelectron spectroscopy and Raman analyses are carried out in order to examine the desired phase formation and substitution of Gd{sup 3+} in the ZnO matrix. Gd{sup 3+} doped ZnO nanoparticles show enhanced photoluminescent and ferromagnetic properties as compared to undoped ZnO. The broad visible emission of ZnO is found to be largely dependent on the surface defects and these surface defects can be tailored by Gd{sup 3+} doping concentration. Furthermore, Gd{sup 3+} doped ZnO nanoparticles also show improved photocatalytic properties as compared with undoped ZnO nanoparticles under ultraviolet irradiation.« less

Diurnal variation of O3, ClO, HOCl, HO2, and BrO observed by JEM/SMILES

NASA Astrophysics Data System (ADS)

Suzuki, Makoto; Mitsuda, Chihiro; Manago, Naohiro; Imai, Koji; Sakazaki, Takatoshi; Ozeki, Hiroyuki; Nishimoto, Eriko; Naito, Yoko; Akiyoshi, Hidehary; Kinnison, Douglas; Sano, Takuki; Shiotani, Masato

2013-04-01

SMILES; Superconducting Submillimeter-Wave Limb Emission Sounder is a 4 K cooled 625-650 GHz limb sounder to observe O3, HCl, ClO, HO2, HOCl, BrO, HNO3, and O3 isotopes. SMILES had been operated on the International Space Station from Oct. 12, 2009 to Apr. 21, 2010. Since ISS is 51° inclined orbit, 30-45 days SMILES zonal mean could provide diurnal variation of chemical species in the stratosphere and mesosphere. Diurnal variation of O3, ClO, HOCl, HO2, and BrO are compared with two nudged CGCM calculations (SD-WACCM; Specified-dynamics WACCM, and MIROC) and satellite observations. Diurnal variation of O3 agreed with SD-WACCM over 50-82 km, but small peak in the morning (7 am local time) is apparent for the SMILES but not for the SD-WACCM at 70 km. Diurnal variation of ClO agreed quite well between SMILES L2 ver. 2.2 and SD-WACCM from 19 to 76 km altitude region. But nighttime ClO value of SMILES L2 ver. 2,2 above 50 km is less than SD-WACCM (70%), which is not clearly explained by the SMILES retrieval issue or our current knowledge of chemical kinetics. Diurnal variation of HOCl also agreed quite nicely from 31 to 76 km. SMILES HOCl retrieval is difficult since it is strongly affected by nearby O3 isotope and O3 hot band lines, as well as very strong HCl line. The nighttime build up of HOCl observed SMILES at 44-68 km are nicely reproduced by the SD-WACCM calculation using JPL2006 chemical kinetics dataset. But chemical kinetics calculation using SMILES ClO, HO2, and HOCl at 35-45 km altitude supported much faster reaction rate of ClO + HO2 given by JPL2010. HO2 diurnal variation also agreed with SD-WACCM from 24 to 72 km. Above 76 km, SMILES L2 ver. 2.2 needs modification of a priori and its co-variance, and we will get better agreement with model calculations. SMILES L2 ver. 2.2 also shows night time bias due to AOS (Acousto-Optics Spectrometer) characteristics. SMILES Band C BrO observation is strongly interfered by overlapping O3 isotope lines, and it is

17O excess transfer during the NO2 + O3 → NO3 + O2 reaction.

PubMed

Berhanu, Tesfaye Ayalneh; Savarino, Joël; Bhattacharya, S K; Vicars, Willliam C

2012-01-28

The ozone molecule possesses a unique and distinctive (17)O excess (Δ(17)O), which can be transferred to some of the atmospheric molecules via oxidation. This isotopic signal can be used to trace oxidation reactions in the atmosphere. However, such an approach depends on a robust and quantitative understanding of the oxygen transfer mechanism, which is currently lacking for the gas-phase NO(2) + O(3) reaction, an important step in the nocturnal production of atmospheric nitrate. In the present study, the transfer of Δ(17)O from ozone to nitrate radical (NO(3)) during the gas-phase NO(2) + O(3) → NO(3) + O(2) reaction was investigated in a series of laboratory experiments. The isotopic composition (δ(17)O, δ(18)O) of the bulk ozone and the oxygen gas produced in the reaction was determined via isotope ratio mass spectrometry. The Δ(17)O transfer function for the NO(2) + O(3) reaction was determined to be: Δ(17)O(O(3)∗) = (1.23 ± 0.19) × Δ(17)O(O(3))(bulk) + (9.02 ± 0.99). The intramolecular oxygen isotope distribution of ozone was evaluated and results suggest that the excess enrichment resides predominantly on the terminal oxygen atoms of ozone. The results obtained in this study will be useful in the interpretation of high Δ(17)O values measured for atmospheric nitrate, thus leading to a better understanding of the natural cycling of atmospheric reactive nitrogen. © 2012 American Institute of Physics

Selective photocatalytic reduction of CO2 by H2O/H2 to CH4 and CH3OH over Cu-promoted In2O3/TiO2 nanocatalyst

NASA Astrophysics Data System (ADS)

Tahir, Muhammad; Tahir, Beenish; Saidina Amin, Nor Aishah; Alias, Hajar

2016-12-01

Photocatalytic CO2 reduction by H2O and/or H2 reductant to selective fuels over Cu-promoted In2O3/TiO2 photocatalyst has been investigated. The samples, prepared via a simple and direct sol-gel method, were characterized by XRD, SEM, TEM, XPS, N2 adsorption-desorption, UV-vis diffuse reflectance, Raman and PL spectroscopy. Cu and In loaded into TiO2, oxidized as Cu2+ and In3+, promoted efficient separation of photo-generated electron/hole pairs (e-/h+). The results indicate that the reduction rate of CO2 by H2O to CH4 approached to 181 μmol g-1 h-1 using 0.5% Cu-3% In2O3/TiO2 catalyst, a 1.53 fold higher than the production rate over the 3% In2O3/TiO2 and 5 times the amount produced over the pure TiO2. In addition, Cu was found to promote efficient production of CH3OH and yield rate reached to 68 μmol g-1 h-1 over 1% Cu-3% In2O3/TiO2 catalyst. This improvement was attributed to charge transfer property and suppressed recombination rate by Cu-metal. More importantly, H2 reductant was less favorable for CH4 production, yet a significant amount of CH4 and CH3OH were obtained using a mixture of H2O/H2 reductant. Therefore, Cu-loaded In2O3/TiO2 catalyst has shown to be capable for methanol production, whereas product selectivity was greatly depending on the amount of Cu-loading and the type of reductant. A photocatalytic reaction mechanism was proposed to understand the experimental results over the Cu-loaded In2O3/TiO2 catalyst.

Detection of aqueous phase chemical warfare agent degradation products by negative mode ion mobility time-of-flight mass spectrometry [IM(tof)MS].

PubMed

Steiner, Wes E; Harden, Charles S; Hong, Feng; Klopsch, Steve J; Hill, Herbert H; McHugh, Vincent M

2006-02-01

The use of negative ion monitoring mode with an atmospheric pressure ion mobility orthogonal reflector time-of-flight mass spectrometer [IM(tof)MS] to detect chemical warfare agent (CWA) degradation products from aqueous phase samples has been determined. Aqueous phase sampling used a traditional electrospray ionization (ESI) source for sample introduction and ionization. Certified reference materials (CRM) of CWA degradation products for the detection of Schedule 1, 2, or 3 toxic chemicals or their precursors as defined by the chemical warfare convention (CWC) treaty verification were used in this study. A mixture of six G-series nerve related CWA degradation products (EMPA, IMPA, EHEP, IHEP, CHMPA, and PMPA) and their related collision induced dissociation (CID) fragment ions (MPA and EPA) were found in each case to be clearly resolved and detected using the IM(tof)MS instrument in negative ion monitoring mode. Corresponding ions, masses, drift times, K(o) values, and signal intensities for each of the CWA degradation products are reported.

Synthesis and cathodoluminescence of beta-Ga2O3 nanowires with holes.

PubMed

Zhang, Xitian; Liu, Zhuang; Hark, Suikong

2008-03-01

Gallium oxide nanowires were synthesized on Si (001) substrate by chemical vapor deposition, using a Ga/Ga2O3 mixture as a precursor and Au as a catalyst. The structure of the as-synthesized products was examined by X-ray powder diffraction and high-resolution transmission electron microscopy, and found to be monoclinic beta-Ga2O3. The morphologies of the beta-Ga2O3 nanowires were characterized by scanning electron microscopy. The majority of the nanowires contain holes along their length, but a few were also found without holes. The holes are believed to be formed by the reaction of adsorbed Ga droplets on reactive terminating surfaces of the nanowires. For nanowires where these reactive surfaces are not exposed, the reaction of Ga is retarded. Cathodoluminescence (CL) of the nanowires was measured. Three emission bands centered at 376, 454, and 666 nm, respectively, were observed.

Possible atmospheric lifetimes and chemical reaction mechanisms for selected HCFCs, HFCs, CH3CCl3, and their degradation products against dissolution and/or degradation in seawater and cloudwater

NASA Technical Reports Server (NTRS)

Wine, P. H.; Chameides, W. L.

1990-01-01

For a wide variety of atmospheric species including CO2, HNO3, and SO2, dissolution in seawater or cloudwater followed by hydrolysis or chemical reaction represents a primary pathway for removal from the atmosphere. In order to determine if this mechanism can also remove significant amounts of atmospheric chlorofluorocarbons (HCFC's), fluorocarbons (HFC's), and their degradation products, an investigation was undertaken as part of the Alternative Fluorocarbons Environmental Acceptability Study (AFEAS). In this investigation, the rates at which CHCl2CF3 (HCFC-123), CCl2FCH3 (HCFC-141b), CClF2CH3 (HCFC-142b), CHClF2 (HCFC-22), CHClFCF3 (HCFC-124) CH2FCF3 (HFC-134a) CHF2CH3 (HFC-152a), CHF2CF3 (HFC-125), and CH3CCl3 can be dissolved in the oceans and in cloudwater were estimated from the species' thermodynamic and chemical properties using simple mathematical formulations to simulate the transfer of gases from the atmosphere to the ocean or cloudwater. The ability of cloudwater and rainwater to remove gas phase degradation products of these compounds was also considered as was the aqueous phase chemistry of the degradation products. The results of this investigation are described.

Mesoporous Pd/Co3O4 nanosheets nanoarrays as an efficient binder/carbon free cathode for rechargeable Li-O2 batteries

NASA Astrophysics Data System (ADS)

Ren, Yanbiao; Zhang, Shichao; Li, Honglei; Wei, Xin; Xing, Yanlan

2017-10-01

In this work, two shapes of mesoporous Co3O4 nanoarrays (i.e., nanosheets, nanowires) were synthesized through a facile hydrothermal method on nickel foam (Ni foam) substrates and tested as the Li-O2 cathodes. The comparison of these two shapes of Co3O4 nanoarrays revealed that the single crystalline feature of Co3O4 nanosheets with a predominant high reactivity {112} exposed crystal plane, favorable nanostructure and high specific area displayed better catalytic performance. Furthermore, a new binder/carbon-free Pd nanoparticles (PdNPs) decorated Co3O4 nanosheets cathode was also fabricated through the chemical reduction method. The presence of PdNPs effectively promotes the uniform growth of a fluffy, porous discharge product Li2O2 layer on the surface of Pd/Co3O4 electrode. The Pd/Co3O4 electrode catalyzed Li-O2 battery exhibited a higher specific capacity (1551 mAh g-1 at 50 mA g-1), lower over-potential and longer cycle life over 72 cycles at 100 mA g-1 with the capacity limited at 300 mAh g-1. The superior catalytic performance for Li-O2 batteries is ascribed to the unique design in both component and architecture of Pd/Co3O4 electrode.

Hydrothermal epitaxy and resultant properties of EuTiO3 films on SrTiO3(001) substrate

PubMed Central

2014-01-01

We report a novel epitaxial growth of EuTiO3 films on SrTiO3(001) substrate by hydrothermal method. The morphological, structural, chemical, and magnetic properties of these epitaxial EuTiO3 films were examined by scanning electron microscopy, transmission electron microscopy, high-resolution X-ray diffractometry, X-ray photoelectron spectroscopy, and superconducting quantum interference device magnetometry, respectively. As-grown EuTiO3 films with a perovskite structure were found to show an out-of-plane lattice shrinkage and room-temperature ferromagnetism, possibly resulting from an existence of Eu3+. Postannealing at 1,000°C could reduce the amount of Eu3+, relax the out-of-plane lattice shrinkage, and impact the magnetic properties of the films. PACS 81.10.Aj; 81.15.-z; 61.05.-a PMID:24948889

Suspect Screening Analysis of Chemicals in Consumer Products.

PubMed

Phillips, Katherine A; Yau, Alice; Favela, Kristin A; Isaacs, Kristin K; McEachran, Andrew; Grulke, Christopher; Richard, Ann M; Williams, Antony J; Sobus, Jon R; Thomas, Russell S; Wambaugh, John F

2018-03-06

A two-dimensional gas chromatography-time-of-flight/mass spectrometry (GC×GC-TOF/MS) suspect screening analysis method was used to rapidly characterize chemicals in 100 consumer products-which included formulations (e.g., shampoos, paints), articles (e.g., upholsteries, shower curtains), and foods (cereals)-and therefore supports broader efforts to prioritize chemicals based on potential human health risks. Analyses yielded 4270 unique chemical signatures across the products, with 1602 signatures tentatively identified using the National Institute of Standards and Technology 2008 spectral database. Chemical standards confirmed the presence of 119 compounds. Of the 1602 tentatively identified chemicals, 1404 were not present in a public database of known consumer product chemicals. Reported data and model predictions of chemical functional use were applied to evaluate the tentative chemical identifications. Estimated chemical concentrations were compared to manufacturer-reported values and other measured data. Chemical presence and concentration data can now be used to improve estimates of chemical exposure, and refine estimates of risk posed to human health and the environment.

Smart chemical sensors using ZnO semiconducting thin films for freshness detection of foods and beverages

NASA Astrophysics Data System (ADS)

Nanto, Hidehito; Kobayashi, Toshiki; Dougami, Naganori; Habara, Masaaki; Yamamoto, Hajime; Kusano, Eiji; Kinbara, Akira; Douguchi, Yoshiteru

1998-07-01

The sensitivity of the chemical sensor, based on the resistance change of Al2O3-doped and SnO2-doped ZnO (ZnO:Al and ZnO:SnO2) thin film, is studied for exposure to various gases. It is found that the ZnO:Al and ZnO:Sn thin film chemical sensor has a high sensitivity and excellent selectivity for amine (TMA and DMA) gas and ethanol gas, respectively. The ZnO:Al (5.0 wt%) thin film chemical sensor which exhibit a high sensitivity for exposure to odors from rotten sea foods, such as salmon, sea bream, oyster, squid and sardine, responds to the freshness change of these sea foods. The ZnO:SnO2 (78 wt%) thin film chemical sensor which exhibit a high sensitivity for exposure to aroma from alcohols, such as wine, Japanese sake, and whisky, responds to the freshness change of these alcohols.

Matrix isolation studies of the interactions of BF3 with water and substituted diethyl ethers. Chemical ionization mass spectrometric determination of the proton affinity of (CF3CH2)2O

NASA Technical Reports Server (NTRS)

Ball, David W.; Zehe, Michael J.

1993-01-01

BF3 was co-condensed with H2O, D2O, (C2H5)2O, (CF3CH2)2O, and (C2F5)2O in excess argon at 15 K. Infrared spectra of BF3/water isolated in solid argon provided a more complete analysis of the BF3--H2O complex than previously published. Infrared spectra of the matrices showed a definite Lewis acid-base interaction between BF3 and diethyl ether; a weak but definite interaction with bis (2,2,2-trifluorodiethyl) ether, and no observable interaction with perfluorodiethyl ether. Thus, the ether data indicate a clear trend between strength of interaction with BF3 and the degree of F substitution. To support and explain the emerging relationship between interaction strength and the basicity of the oxygen-containing molecule, the proton affinity of (CF3CH2)2O was measured using chemical ionization mass spectrometry. The implications of the results for lubricant/metal oxide surface interactions are discussed.

Viscosity of TiO2-FeO-Ti2O3-SiO2-MgO-CaO-Al2O3 for High-Titania Slag Smelting Process

NASA Astrophysics Data System (ADS)

Hu, Kai; Lv, Xuewei; Li, Shengping; Lv, Wei; Song, Bing; Han, Kexi

2018-05-01

The present study demonstrates the dependence of viscosity on chemical composition and temperature of high-titania slag, a very important raw material for producing titanium dioxide. The results indicated that completely molten high-titania slag exhibits a viscosity of less than 1 dPa s with negligible dependence on temperature. However, it increases dramatically with decreasing temperature slightly below the critical temperature, i.e., the solidus temperature of the slag. Above the critical temperature, the slag samples displayed the same order of viscosity at 0.6 dPa s, regardless of their compositional variation. However, the FeO, CaO, and MgO were confirmed to decrease viscosity, while SiO2 and Ti2O3 increase it. The apparent activation energy for viscosity-temperature relation and liquidus temperature based on experiments and thermodynamic calculations are also presented. Conclusively, the critical temperatures of the slags are on average 15 K below their corresponding calculated liquidus temperatures. The increase in FeO content was found to considerably lower the critical temperature, while the increase in both Ti2O3 and TiO2 contents increases it. The main phases of the slag in solid state, as indicated by X-ray diffraction, are (Fe, Mg) x Ti y O5 (x + y = 3, pseudobrookite) and rutile.

Nitrous oxide production from reactive nitrification intermediates: a concerted action of biological and chemical processes

NASA Astrophysics Data System (ADS)

Brüggemann, Nicolas; Heil, Jannis; Liu, Shurong; Wei, Jing; Vereecken, Harry

2017-04-01

This contribution tries to open up a new perspective on biogeochemical N2O production processes, taking the term bio-geo-chemistry literally. What if a major part of N2O is produced from reactive intermediates of microbiological N turnover processes ("bio…") leaking out of the involved microorganisms into the soil ("…geo…") and then reacting chemically ("…chemistry") with the surrounding matrix? There are at least two major reactive N intermediates that might play a significant role in these coupled biological-chemical reactions, i.e. hydroxylamine (NH2OH) and nitrite (NO2-), both of which are produced during nitrification under oxic conditions, while NO2- is also produced during denitrification under anoxic conditions. Furthermore, NH2OH is assumed to be also a potential intermediate of DNRA and/or anammox. First, this contribution will summarize information about several chemical reactions involving NH2OH and NO2- leading to the formation of N2O. These abiotic reactions are: reactions of NO2- with reduced metal cations, nitrosation reactions of NO2- and soil organic matter (SOM), the reaction between NO2- and NH2OH, and the oxidation of NH2OH by oxidized metal ions. While these reactions can occur over a broad range of soil characteristics, they are ignored in most current N trace gas studies in favor of biological processes only. Disentangling microbiological from purely chemical N2O production is further complicated by the fact that the chemically formed N2O is either undiscernible from N2O produced during nitrification, or shows an intermediate 15N site preference between that of N2O from nitrification and denitrification, respectively. Results from experiments with live and sterilized soil samples, with artificial soil mixtures and with phenolic lignin decomposition model compounds will be presented that demonstrate the potential contribution of these abiotic processes to soil N trace gas emissions, given a substantial leakage rate of these reactive

Actinometric measurement of j(O3-O(1D)) using a luminol detector

NASA Technical Reports Server (NTRS)

Bairai, Solomon T.; Stedman, Donald H.

1992-01-01

The photolysis frequency of ozone to singlet D oxygen atoms has been measured by means of a chemical actinometer using a luminol based detector. The instrument measures j(O3-O(1D)) with a precision of 10 percent. The data collected in winter and spring of 1991 is in agreement with model predictions and previously measured values. Data from a global solar radiometer can be used to estimate the effects of local cloudiness on j(O3-O(1D)).

Double quantum dots decorated 3D graphene flowers for highly efficient photoelectrocatalytic hydrogen production

NASA Astrophysics Data System (ADS)

Cheng, Qifa; Xu, Jing; Wang, Tao; Fan, Ling; Ma, Ruifang; Yu, Xinzhi; Zhu, Jian; Xu, Zhi; Lu, Bingan

2017-11-01

Photoelectrocatalysis (PEC) has been demonstrated as a promising technique for hydrogen production. However, the high over-potential and high recombination rate of photo-induced electron-hole pairs lead to poor hydrogen production efficiency. In order to overcome these problems, TiO2 and Au dual quantum dots (QDs) on three-dimensional graphene flowers (Au@TiO2@3DGFs) was synthesized by an electro-deposition strategy. The combination of Au and TiO2 modulates the band gap of TiO2, shifts the absorption to visible lights and improves the utilization efficiency of solar light. Simultaneously, the size-quantization TiO2 on 3DGFs not only achieves a larger specific surface area over conventional nanomaterials, but also promotes the separation of the photo-induced electron-hole pairs. Besides, the 3DGFs as a scaffold for QDs can provide more active sites and stable structure. Thus, the newly-developed Au@TiO2@3DGFs composite exhibited an impressive PEC activity and excellent durability. Under -240 mV potential (vs. RHE), the photoelectric current density involved visible light illumination (100 mW cm-2) reached 90 mA cm-2, which was about 3.6 times of the natural current density (without light, only 25 mA cm-2). It worth noting that the photoelectric current density did not degrade and even increased to 95 mA cm-2 over 90 h irradiation, indicating an amazing chemical stability.

Direct Correlations of Grain Boundary Potentials to Chemical States and Dielectric Properties of Doped CaCu3Ti4O12 Thin Films.

PubMed

Cho, Ahra; Han, Chan Su; Kang, Meenjoo; Choi, Wooseok; Lee, Jihwan; Jeon, Jaecheol; Yu, Sujae; Jung, Ye Seul; Cho, Yong Soo

2018-05-09

Colossal dielectric constant CaCu 3 Ti 4 O 12 has been recognized as one of the rare materials having intrinsic interfacial polarization and thus unusual dielectric characteristics, in which the electrical state of the grain boundary is critical. Here, the direct correlation between the grain boundary potential and relative permittivity is proposed for the CaCu 3 Ti 4 O 12 thin films doped with Zn, Ga, Mn, and Ag as characterized by Kelvin probe force microscopy. The dopants are intended to provide the examples of variable grain boundary potentials that are driven by chemical states including Cu + , Ti 3+ , and oxygen vacancy. Grain boundary potential is nearly linearly proportional to the dielectric constant. This effect is attributed to the increased charge accumulation near the grain boundary, depending on the choice of the dopant. As an example, 1 mol % Ag-doped CaCu 3 Ti 4 O 12 thin films demonstrate the best relative permittivity as associated with a higher grain boundary potential of 120.3 mV compared with 82.6 mV for the reference film. The chemical states across grain boundaries were further verified by using spherical aberration-corrected scanning transmission electron microscopy with the simultaneous electron energy loss spectroscopy.

Synthesis, characterization and wound healing imitation of Fe3O4 magnetic nanoparticle grafted by natural products

NASA Astrophysics Data System (ADS)

Pala, Sravan Kumar

This research focused on the study of the core-shelled magnetic nanomaterials derived from a colloidal chemistry. The goals are four-fold: (1) synthesis of Fe3O4MNMs using colloidal chemistry. The Fe 3O4 MNMs were then grafted with extracts derived from natural products, namely Olecraceavar italica (broccoli), Boletus edulis (mushroom)and Solanum lycopersicum (tomato);(2)characterization of natural products by chromatography and mass spectrometry;(3) characterization of MNMs to determine their crystallinity, morphological and elemental composition by the state-of-the-art instruments; and (4) biological evaluation using Gram-negative and Gram-positive bacteria. The approach provides advantages to precisely control the composition and homogeneity. The second advantage of the colloidal chemistry is its user friendliness and feasibility. Due to the nature of the natural products, the compatibility of MNM is anticipated to be enhanced.In this chapter, the nanomaterials will be discussed from four perspectives,§1.1 Nanotechnology (§1.1), §1.2 Synthesis of nanomaterials; §1.3 The natural product extract,; §1.4 Characterization of nanomaterials; and §1.5Biological application of nanomaterials.Fig. 1 summarized the overarching goals of this study.

Extracellular biosynthesis of gadolinium oxide (Gd2O3) nanoparticles, their biodistribution and bioconjugation with the chemically modified anticancer drug taxol

PubMed Central

Khan, Shadab Ali; Gambhir, Sanjay

2014-01-01

Summary As a part of our programme to develop nanobioconjugates for the treatment of cancer, we first synthesized extracellular, protein-capped, highly stable and well-dispersed gadolinium oxide (Gd2O3) nanoparticles by using thermophilic fungus Humicola sp. The biodistribution of the nanoparticles in rats was checked by radiolabelling with Tc-99m. Finally, these nanoparticles were bioconjugated with the chemically modified anticancer drug taxol with the aim of characterizing the role of this bioconjugate in the treatment of cancer. The biosynthesized Gd2O3 nanoparticles were characterized by UV–vis spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoemission spectroscopy (XPS). The Gd2O3–taxol bioconjugate was confirmed by UV–vis spectroscopy and fluorescence microscopy and was purified by using high performance liquid chromatography (HPLC). PMID:24778946

Heteroepitaxial growth of ɛ-(AlxGa1-x)2O3 alloy films on c-plane AlN templates by mist chemical vapor deposition

NASA Astrophysics Data System (ADS)

Tahara, Daisuke; Nishinaka, Hiroyuki; Morimoto, Shota; Yoshimoto, Masahiro

2018-04-01

In this study, ɛ-(AlxGa1-x)2O3 alloy films were grown on c-plane AlN templates by mist chemical vapor deposition. The Al content of two samples was determined by Rutherford backscattering analysis. The lattice constant of the ɛ-(AlxGa1-x)2O3 alloy films followed Vegard's law, and the Al contents of other samples were determined to be as high as x = 0.395 by Vegard's law. The direct bandgap was obtained in the range of 5.0-5.9 eV by transmittance measurements. The valence-band offset between ɛ-(Al0.395Ga0.605)2O3 and ɛ-Ga2O3 was analyzed to be 0.2 eV, and the conduction-band offset was calculated to be 0.7 eV by X-ray photoelectron spectroscopy. The ɛ-(AlxGa1-x)2O3/ɛ-Ga2O3 interface band discontinuity was type I. Our experimental results will be important for the actual application of ɛ-(AlxGa1-x)2O3/ɛ-Ga2O3 heterojunction devices.

Synthesis of novel 3'-azido-3'-deoxy-α-L-ribo configured nucleosides: A comparative study between chemical and chemo-enzymatic methodologies.

PubMed

Rana, Neha; Kumar, Manish; Singh, Ankita; Maity, Jyotirmoy; Shukla, Poonam; Prasad, Ashok K

2018-05-03

Syntheses of novel 3'-azido-3'-deoxy-2'-O,4'-C-methylene-α-L-ribofuranosyl nucleosides have been carried out from 3'-azido-3'-deoxy-4'-C-hydroxymethyl-β-D-xylofuranosyl nucleosides following both chemical and chemo-enzymatic methodologies. The precursor nucleoside in turn was synthesized from a common glycosyl donor 4-C-acetoxymethyl-1,2,5-tri-O-acetyl-3-azido-3-deoxy-α,β-D-xylofuranose, which was obtained by the acetolysis of 4-C-acetoxymethyl-5-O-acetyl-3-azido-3-deoxy-1,2-O-isopropylidene-α-D-xylofuranose in 96% yield. It has been observed that a chemo-enzymatic pathway for the synthesis of targeted nucleosides is much more efficient than a chemical pathway, leading to the improvement in yield for the synthesis of 3'-azido-3'-deoxy-α-L-ribofuranosyl thymine and uracil from 49 to 89% and 55 to 93%, respectively.

The effects of ionic liquid 1-ethyl-3-methylimidazolium trifluoromethanesulfonate on the production of 1,3-propanediol from crude glycerol by microbial consortium.

PubMed

Jiang, Lili; Dai, Jianying; Sun, Yaqin; Xiu, Zhilong

2018-04-12

Ionic liquids (ILs) as "green" solvents have been widely used owing to their excellent properties, e.g., for biodiesel production. Crude glycerol as a by-product in biodiesel production is an ideal feedstock for the microbial production of 1,3-propanediol (PDO), which is a versatile bulk chemical. PDO can be produced by microbial consortium with the advantages of high substrate tolerance and narrow by-product profile. In the present study, the effect of IL 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([Emim][TfO]) was evaluated on the capacity of PDO production from crude glycerol by microbial consortium DL38-BH. In the batch fermentation at 60 g/L crude glycerol and 10 g/L [Emim][TfO], the concentration and yield of PDO from glycerol increased from 23.14 g/L and 0.45 mol/mol to 31.17 g/L and 0.60 mol/mol, respectively. Our results showed that [Emim][TfO] decreased the ratio of intracellular NADH to NAD + and increased the concentration of 3-HPA during batch fermentation. The activities of three key enzymes in glycerol metabolism were stimulated by [Emim][TfO] during the batch fermentation by microbial consortium DL38-BH. Compared to the control, the proportion of Klebsiella genus which could convert glycerol to PDO increased significantly from 79.19% to 89.49% and the other genera that did not produce PDO were dramatically decreased (P < 0.05) at the end of batch fermentation. This work demonstrated that [Emim][TfO] significantly improved the concentration and yield of PDO from crude glycerol by adjusting microbial community during batch fermentation by microbial consortium.

Reaction between NiO and Al2O3 in NiO/γ-Al2O3 catalysts probed by positronium atom

NASA Astrophysics Data System (ADS)

Li, C. Y.; Zhang, H. J.; Chen, Z. Q.

2013-02-01

NiO/γ-Al2O3 catalysts with NiO content of 9 wt% and 24 wt% were prepared by solid state reaction method. They are annealed in air at temperatures from 100 °C to 1000 °C. Positron lifetime spectra were measured to study the microstructure variation during annealing process. Four positron lifetime components were resolved with two long lifetime τ3 and τ4, which can be attributed to the ortho-positronium lifetime in microvoids and large pores, respectively. It was found that the longest lifetime τ4 is rather sensitive to the chemical environment of the large pores. The NiO active centers in the catalysts cause decrease of both τ4 and its intensity I4, which is due to the spin-conversion of positronium induced by NiO. However, after heating the catalysts above 600 °C, abnormal increase of the lifetime τ4 is observed. This is due to the formation of NiAl2O4 spinel from the reaction of NiO and γ-Al2O3. The generated NiAl2O4 weakens the spin-conversion effect of positronium, thus leads to the increase of o-Ps lifetime τ4. Formation of NiAl2O4 is further confirmed by both X-ray diffraction and X-ray photoelectron spectroscopy measurements.

Facile synthesis and paramagnetic properties of Fe3O4@SiO2 core-shell nanoparticles

NASA Astrophysics Data System (ADS)

Yang, Lili; Zou, Ping; Cao, Jian; Sun, Yunfei; Han, Donglai; Yang, Shuo; Chen, Gang; Kong, Xiangwang; Yang, Jinghai

2014-12-01

The Fe3O4@SiO2 core-shell nanoparticles (NPs) had been successfully fabricated via direct decomposition of tetraethyl orthosilicate (TEOS) in solution under the presence of as-synthesized Fe3O4 NPs prepared by chemical coprecipitation method. The structure and magnetic properties of Fe3O4@SiO2 NPs were characterized and the result indicated that Fe3O4@SiO2 NPs are about 12 nm in size with paramagnetic property. The possible growth and magnetic mechanism was discussed in detail.

Absence of morphotropic phase boundary effects in BiFeO3-PbTiO3 thin films grown via a chemical multilayer deposition method

NASA Astrophysics Data System (ADS)

Gupta, Shashaank; Bhattacharjee, Shuvrajyoti; Pandey, Dhananjai; Bansal, Vipul; Bhargava, Suresh K.; Peng, Ju Lin; Garg, Ashish

2011-07-01

We report an unusual behavior observed in (BiFeO3)1- x -(PbTiO3) x (BF- xPT) thin films prepared using a multilayer chemical solution deposition method. Films of different compositions were grown by depositing several bilayers of BF and PT precursors of varying BF and PT layer thicknesses followed by heat treatment in air. X-ray diffraction showed that samples of all compositions show mixing of two compounds resulting in a single-phase mixture, also confirmed by transmission electron microscopy. In contrast to bulk compositions, samples show a monoclinic (MA-type) structure suggesting disappearance of the morphotropic phase boundary (MPB) at x=0.30 as observed in the bulk. This is accompanied by the lack of any enhancement of the remanent polarization at the MPB, as shown by the ferroelectric measurements. Magnetic measurements showed an increase in the magnetization of the samples with increasing BF content. Significant magnetization in the samples indicates melting of spin spirals in the BF- xPT films, arising from a random distribution of iron atoms. Absence of Fe2+ ions was corroborated by X-ray photoelectron spectroscopy measurements. The results illustrate that thin film processing methodology significantly changes the structural evolution, in contrast to predictions from the equilibrium phase diagram, besides modifying the functional characteristics of the BP- xPT system dramatically.

Pd/CeO2/SiC Chemical Sensors

NASA Technical Reports Server (NTRS)

Lu, Weijie; Collins, W. Eugene

2005-01-01

The incorporation of nanostructured interfacial layers of CeO2 has been proposed to enhance the performances of Pd/SiC Schottky diodes used to sense hydrogen and hydrocarbons at high temperatures. If successful, this development could prove beneficial in numerous applications in which there are requirements to sense hydrogen and hydrocarbons at high temperatures: examples include monitoring of exhaust gases from engines and detecting fires. Sensitivity and thermal stability are major considerations affecting the development of high-temperature chemical sensors. In the case of a metal/SiC Schottky diode for a number of metals, the SiC becomes more chemically active in the presence of the thin metal film on the SiC surface at high temperature. This increase in chemical reactivity causes changes in chemical composition and structure of the metal/SiC interface. The practical effect of the changes is to alter the electronic and other properties of the device in such a manner as to degrade its performance as a chemical sensor. To delay or prevent these changes, it is necessary to limit operation to a temperature <450 C for these sensor structures. The present proposal to incorporate interfacial CeO2 films is based partly on the observation that nanostructured materials in general have potentially useful electrical properties, including an ability to enhance the transfer of electrons. In particular, nanostructured CeO2, that is CeO2 with nanosized grains, has shown promise for incorporation into hightemperature electronic devices. Nanostructured CeO2 films can be formed on SiC and have been shown to exhibit high thermal stability on SiC, characterized by the ability to withstand temperatures somewhat greater than 700 C for limited times. The exchanges of oxygen between CeO2 and SiC prevent the formation of carbon and other chemical species that are unfavorable for operation of a SiC-based Schottky diode as a chemical sensor. Consequently, it is anticipated that in a Pd/CeO

Comparison of the physical, chemical and electrical properties of ALD Al 2 O 3 on c- and m- plane GaN: Comparison of the physical, chemical and electrical properties of ALD Al 2 O 3 on c- and m- plane GaN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wei, D.; Hossain, T.; Nepal, N.

2014-02-01

Our study compares the physical, chemical and electrical properties of Al 2O 3 thin films deposited on gallium polar c- and nonpolar m -plane GaN substrates by atomic layer deposition (ALD). Correlations were sought between the film's structure, composition, and electrical properties. The thickness of the Al 2O 3 films was 19.2 nm as determined from a Si witness sample by spectroscopic ellipsometry. We measured the gate dielectric was slightly aluminum-rich (Al:O=1:1.3) from X-ray photoelectron spectroscopy (XPS) depth profile, and the oxide-semiconductor interface carbon concentration was lower on c -plane GaN. The oxide's surface morphology was similar on both substrates,more » but was smoothest on c -plane GaN as determined by atomic force microscopy (AFM). Circular capacitors (50-300 μm diameter) with Ni/Au (20/100 nm) metal contacts on top of the oxide were created by standard photolithography and e-beam evaporation methods to form metal-oxide-semiconductor capacitors (MOSCAPs). Moreover, the alumina deposited on c -plane GaN showed less hysteresis (0.15 V) than on m -plane GaN (0.24 V) in capacitance-voltage (CV) characteristics, consistent with its better quality of this dielectric as evidenced by negligible carbon contamination and smooth oxide surface. These results demonstrate the promising potential of ALD Al 2O 3 on c -plane GaN, but further optimization of ALD is required to realize the best properties of Al 2O 3 on m -plane GaN.« less

Comparison of methods for the determination of NO-O3-NO2 fluxes and chemical interactions over a bare soil

NASA Astrophysics Data System (ADS)

Stella, P.; Loubet, B.; Laville, P.; Lamaud, E.; Cazaunau, M.; Laufs, S.; Bernard, F.; Grosselin, B.; Mascher, N.; Kurtenbach, R.; Mellouki, A.; Kleffmann, J.; Cellier, P.

2011-08-01

Tropospheric ozone (O3) is a known greenhouse gas responsible for impacts on human and animal health and ecosystem functioning. In addition, O3 plays an important role in tropospheric chemistry, together with nitrogen oxides. Flux measurements of these trace gases are a major issue to establish their atmospheric budget and evaluate the ozone impact onto the biosphere. In this study, ozone, nitric oxide (NO) and nitrogen dioxide (NO2) fluxes were measured using the aerodynamic gradient method over a bare soil in an agricultural field. Vertical mixing ratio profile measurements were performed with fast response sensors. It was demonstrated that corrections of the aerodynamic gradient for chemical reactions between O3-NO-NO2 appeared to be negligible for O3 fluxes, whereas they accounted for about 10 % on average of the NO and NO2 fluxes. The flux uncertainties were mainly due to uncertainties of the friction velocity. In addition, the use of fast response sensors allowed to reduce the remaining part of the flux uncertainty. The aerodynamic gradient and eddy-covariance methods gave similar O3 fluxes (within 4 %). The chamber NO fluxes were up to 70 % lower than the aerodynamic gradient fluxes probably caused by either the spatial heterogeneity of the soil NO emissions or the environmental perturbation due to the chamber.

Engineering an Obligate Photoautotrophic Cyanobacterium to Utilize Glycerol for Growth and Chemical Production.

PubMed

Kanno, Masahiro; Atsumi, Shota

2017-01-20

Cyanobacteria have attracted much attention as a means to directly recycle carbon dioxide into valuable chemicals that are currently produced from petroleum. However, the titers and productivities achieved are still far below the level required in industry. To make a more industrially applicable production scheme, glycerol, a byproduct of biodiesel production, can be used as an additional carbon source for photomixotrophic chemical production. Glycerol is an ideal candidate due to its availability and low cost. In this study, we found that a heterologous glycerol respiratory pathway enabled Synechococcus elongatus PCC 7942 to utilize extracellular glycerol. The engineered strain produced 761 mg/L of 2,3-butanediol in 48 h with a 290% increase over the control strain under continuous light conditions. Glycerol supplementation also allowed for continuous cell growth and 2,3-butanediol production in diurnal light conditions. These results highlight the potential of glycerol as an additional carbon source for photomixotrophic chemical production in cyanobacteria.

Comparing electrical characteristics of in situ and ex situ Al2O3/GaN interfaces formed by metalorganic chemical vapor deposition

NASA Astrophysics Data System (ADS)

Chan, Silvia H.; Bisi, Davide; Tahhan, Maher; Gupta, Chirag; DenBaars, Steven P.; Keller, Stacia; Zanoni, Enrico; Mishra, Umesh K.

2018-04-01

Al2O3/n-GaN MOS-capacitors grown by metalorganic chemical vapor deposition with in-situ- and ex-situ-formed Al2O3/GaN interfaces were characterized. Capacitors grown entirely in situ exhibited ˜4 × 1012 cm-2 fewer positive fixed charges and up to ˜1 × 1013 cm-2 eV-1 lower interface-state density near the band-edge than did capacitors with ex situ oxides. When in situ Al2O3/GaN interfaces were reformed via the insertion of a 10-nm-thick GaN layer, devices exhibited behavior between the in situ and ex situ limits. These results illustrate the extent to which an in-situ-formed dielectric/GaN gate stack improves the interface quality and breakdown performance.

Composition and production rate of pharmaceutical and chemical waste from Xanthi General Hospital in Greece

DOE Office of Scientific and Technical Information (OSTI.GOV)

Voudrias, Evangelos, E-mail: voudrias@env.duth.gr; Goudakou, Lambrini; Kermenidou, Marianthi

2012-07-15

Highlights: Black-Right-Pointing-Pointer We studied pharmaceutical and chemical waste production in a Greek hospital. Black-Right-Pointing-Pointer Pharmaceutical waste comprised 3.9% w/w of total hazardous medical waste. Black-Right-Pointing-Pointer Unit production rate for total pharmaceutical waste was 12.4 {+-} 3.90 g/patient/d. Black-Right-Pointing-Pointer Chemical waste comprised 1.8% w/w of total hazardous medical waste. Black-Right-Pointing-Pointer Unit production rate for total chemical waste was 5.8 {+-} 2.2 g/patient/d. - Abstract: The objective of this work was to determine the composition and production rates of pharmaceutical and chemical waste produced by Xanthi General Hospital in Greece (XGH). This information is important to design and cost management systems formore » pharmaceutical and chemical waste, for safety and health considerations and for assessing environmental impact. A total of 233 kg pharmaceutical and 110 kg chemical waste was collected, manually separated and weighed over a period of five working weeks. The total production of pharmaceutical waste comprised 3.9% w/w of the total hazardous medical waste produced by the hospital. Total pharmaceutical waste was classified in three categories, vial waste comprising 51.1%, syringe waste with 11.4% and intravenous therapy (IV) waste with 37.5% w/w of the total. Vial pharmaceutical waste only was further classified in six major categories: antibiotics, digestive system drugs, analgesics, hormones, circulatory system drugs and 'other'. Production data below are presented as average (standard deviation in parenthesis). The unit production rates for total pharmaceutical waste for the hospital were 12.4 (3.90) g/patient/d and 24.6 (7.48) g/bed/d. The respective unit production rates were: (1) for vial waste 6.4 (1.6) g/patient/d and 13 (2.6) g/bed/d, (2) for syringe waste 1.4 (0.4) g/patient/d and 2.8 (0.8) g/bed/d and (3) for IV waste 4.6 (3.0) g/patient/d and 9.2 (5.9) g/bed/d. Total

Chemical dynamics simulations of the monohydrated OH-(H2O) + CH3I reaction. Atomic-level mechanisms and comparison with experiment

NASA Astrophysics Data System (ADS)

Xie, Jing; Otto, Rico; Wester, Roland; Hase, William L.

2015-06-01

Direct dynamics simulations, with B97-1/ECP/d theory, were performed to study the role of microsolvation for the OH-(H2O) + CH3I reaction. The SN2 reaction dominates at all reactant collision energies, but at higher collision energies proton transfer to form CH2I-, and to a lesser extent CH2I- (H2O), becomes important. The SN2 reaction occurs by direct rebound and stripping mechanisms, and 28 different indirect atomistic mechanisms, with the latter dominating. Important components of the indirect mechanisms are the roundabout and formation of SN2 and proton transfer pre-reaction complexes and intermediates, including [CH3--I--OH]-. In contrast, for the unsolvated OH- + CH3I SN2 reaction, there are only seven indirect atomistic mechanisms and the direct mechanisms dominate. Overall, the simulation results for the OH-(H2O) + CH3IߙSN2 reaction are in good agreement with experiment with respect to reaction rate constant, product branching ratio, etc. Differences between simulation and experiment are present for the SN2 velocity scattering angle at high collision energies and the proton transfer probability at low collision energies. Equilibrium solvation by the H2O molecule is unimportant. The SN2 reaction is dominated by events in which H2O leaves the reactive system as CH3OH is formed or before CH3OH formation. Formation of solvated products is unimportant and participation of the (H2O)CH3OH---I- post-reaction complex for the SN2 reaction is negligible.

Chemical production in electrocautery smoke by a novel predictive model.

PubMed

Wu, Y-C; Tang, C-S; Huang, H-Y; Liu, C-H; Chen, Y-L; Chen, D-R; Lin, Y-W

2011-01-01

The hazards of electrocautery smoke have been known for decades. However, few clinical studies have been conducted to analyze the responsible variables of the smoke production. This study collected clinical smoke samples and systematically analyzed all possible factors. Thirty diathermy smoke samples were collected during mastectomy and abdominal cavity operations. Samples were analyzed using a gas chromatographer with a flame ionization detector. Data were applied to construct prediction models for chemical production from electrosurgeries to identify all possible factors that impact chemical production during electrosurgery. Toluene was detected in 27 smoke samples (90%) with concentrations of 0.003-0.463 mg/m(3) and production of 176.0-2,780.0 ng. Ethyl benzene and styrene were identified in very few cases. General linear regression analysis demonstrates that surgery type, patient age, electrocautery duration and imparted coagulation energy explained 67.63% of the variation in toluene production. Surgery type and patient age are known prior to surgery. In terms of risk precaution, the operating team should pay close attention to exposure when certain positive factors of increasing the chemical production are known in advance. Copyright © 2011 S. Karger AG, Basel.

Comparison of methods for the determination of NO-O3-NO2 fluxes and chemical interactions over a bare soil

NASA Astrophysics Data System (ADS)

Stella, P.; Loubet, B.; Laville, P.; Lamaud, E.; Cazaunau, M.; Laufs, S.; Bernard, F.; Grosselin, B.; Mascher, N.; Kurtenbach, R.; Mellouki, A.; Kleffmann, J.; Cellier, P.

2012-06-01

Tropospheric ozone (O3) is a known greenhouse gas responsible for impacts on human and animal health and ecosystem functioning. In addition, O3 plays an important role in tropospheric chemistry, together with nitrogen oxides. The determination of surface-atmosphere exchange fluxes of these trace gases is a prerequisite to establish their atmospheric budget and evaluate their impact onto the biosphere. In this study, O3, nitric oxide (NO) and nitrogen dioxide (NO2) fluxes were measured using the aerodynamic gradient method over a bare soil in an agricultural field. Ozone and NO fluxes were also measured using eddy-covariance and automatic chambers, respectively. The aerodynamic gradient measurement system, composed of fast response sensors, was capable to measure significant differences in NO and O3 mixing ratios between heights. However, due to local advection, NO2 mixing ratios were highly non-stationary and NO2 fluxes were, therefore, not significantly different from zero. The chemical reactions between O3, NO and NO2 led to little ozone flux divergence between the surface and the measurement height (less than 1% of the flux on average), whereas the NO flux divergence was about 10% on average. The use of fast response sensors allowed reducing the flux uncertainty. The aerodynamic gradient and the eddy-covariance methods gave comparable O3 fluxes. The chamber NO fluxes were down to 70% lower than the aerodynamic gradient fluxes, probably because of either the spatial heterogeneity of the soil NO emissions or the perturbation due to the chamber itself.