MnFe2O4 as a gas sensor towards SO2 and NO2 gases

NASA Astrophysics Data System (ADS)

Rathore, Deepshikha; Mitra, Supratim

2016-05-01

The chemical co-precipitation method was used to synthesize MnFe2O4 nanoparticles. Single cubic phase formation of nanoparticles was confirmed by X-ray diffraction technique. The average particle size of MnFe2O4 nanoparticles was found to be 10.7 nm using Scherrer formula. The ultrafine powder of MnFe2O4 nanoparticles was pressed to design pellet of 10 mm diameter and 1mm thickness. Copper electrodes have been deposited on the surface of pellet using silver paste in the form of capacitor. Fabricated gas sensing device of MnFe2O4 nanoparticles was tested towards SO2 and NO2 gases. Cole-Cole plot of MnFe2O4 was investigated with the help of electrochemical workstation. The performance of the sensors including sensitivity, response and recovery time was also determined. It was observed that the MnFe2O4 nanoparticles are more sensible for NO2 gas as compared to SO2 gas.

New Insight into SO2 Poisoning and Regeneration of CeO2-WO3/TiO2 and V2O5-WO3/TiO2 Catalysts for Low-Temperature NH3-SCR.

PubMed

Xu, Liwen; Wang, Chizhong; Chang, Huazhen; Wu, Qingru; Zhang, Tao; Li, Junhua

2018-06-19

In this study, the poisoning effects of SO 2 on the V 2 O 5 -WO 3 /TiO 2 (1%VWTi) and CeO 2 -WO 3 /TiO 2 (5%CeWTi) selective catalytic reduction (SCR) catalysts were investigated in the presence of steam, and also the regeneration of deactivated catalysts was studied. After pretreating the catalysts in a flow of NH 3 + SO 2 + H 2 O + O 2 at 200 °C for 24 h, it was observed that the low-temperature SCR (LT-SCR) activity decreased significantly over the 1%VWTi and 5%CeWTi catalysts. For 1%VWTi, NH 4 HSO 4 (ABS) was the main product detected after the poisoning process. Both of NH 4 HSO 4 and cerium sulfate species were formed on the poisoned 5%CeWTi catalyst, indicating that SO 2 reacted with Ce 3+ /Ce 4+ , even in the presence of high concentration of NH 3 . The decrease of BET specific surface area, NO x adsorption capacity, the ratio of chemisorbed oxygen, and reducibility were responsible for the irreversible deactivation of the poisoned 5%CeWTi catalyst. Meanwhile, the LT-SCR activity could be recovered over the poisoned 1%VWTi after regeneration at 400 °C, but not for the 5%CeWTi catalyst. For industrial application, it is suggested that the regeneration process can be utilized for 1%VWTi catalysts after a period of time after NH 4 HSO 4 accumulated on the catalysts.

Processes of Molecular Relaxation in Binary Crystalline Systems KNO3-KClO4, KNO3-KNO2, and K2CO3-K2SO4

NASA Astrophysics Data System (ADS)

Aliev, A. R.; Akhmedov, I. R.; Kakagasanov, M. G.; Aliev, Z. A.; Gafurov, M. M.; Rabadanov, K. Sh.; Amirov, A. M.

2018-03-01

The processes of molecular relaxation in binary crystalline systems KNO3-KClO4, KNO3-KNO2, and K2CO3-K2SO4 are studied via differential thermal analysis and Raman spectroscopy. It is found that the relaxation time of the vibrations ν1( A) of anions NO- 3 and CO2- 3 in systems KNO3-KClO4, KNO3-KNO2, and K2CO3-K2SO4 is less than that in KNO3 and K2CO3, respectively. It is shown that the increased rate of relaxation is explained by an additional relaxation mechanism presented in the system. This mechanism is associated with the excitation of vibrations of anions ClO- 4, NO- 2, and SO2- 4 and the lattice phonons that emerge. It is found that this relaxation mechanism requires correspondence of the frequency difference of these vibrations to the region of sufficiently high density of states of the phonon spectrum.

Synthesis of cationic iridium(I) complexes of water-soluble phosphine ligands, [Ir(CO)(TPPMS){sub 3}]CF{sub 3}SO{sub 3}, [Ir(CO)(H{sub 2}O)(TPPTS){sub 2}]CF{sub 3}SO{sub 3}, and [Ir(CO){sub 2}(TPPMS){sub 3}]ClO{sub 4} (TPPMS = PPh{sub 2}(m-C{sub 6}H{sub 4}SO{sub 3}K), TPPTS = P(m-C{sub 6}H{sub 4}SO{sub 3}Na){sub 3})

DOE Office of Scientific and Technical Information (OSTI.GOV)

Paterniti, D.P.; Francisco, L.W.; Atwood, J.D.

Several new water-soluble iridium(I) complexes were synthesized and their reactivities with small molecules (H{sub 2} or CO) in polar solvents (DMSO or H{sub 2}O) examined. Reaction of H{sub 2} with [Ir(CO)(TPPMS){sub 3}]CF{sub 3}SO{sub 3} (TPPMS = P(C{sub 6}H{sub 5}){sub 2}(m-C{sub 6}H{sub 4}SO{sub 3}K)) in DMSO or H{sub 2}O produces [cis,mer-Ir(CO)(H){sub 2}(TPPMS){sub 3}]CF{sub 3}SO{sub 3}, while the reaction of CO with [Ir(CO)(TPPMS){sub 3}]-CF{sub 3}SO{sub 3} in water yields [Ir(CO){sub 2}(TPPMS){sub 3}]CF{sub 3}SO{sub 3}. Carbonylation of [Ir(CO){sub 2}(TPPMS){sub 3}]ClO{sub 4} in DMSO produces [Ir(CO){sub 3}(TPPMS){sub 2}]ClO{sub 4} and TPPMS; no reaction is observed in H{sub 2}O. Hydrogenation of [Ir(CO){sub 2}(TPPMS){sub 3}]ClO{sub 4}more » in DMSO or H{sub 2}O yields [cis,mer-Ir(CO)(H){sub 2}(TPPMS){sub 3}]ClO{sub 4}, while reaction of H{sub 2} with an aqueous solution of [Ir(CO)(H{sub 2}O)(TPPTS){sub 2}]CF{sub 3}SO{sub 3} produces [Ir(CO)(H{sub 2}O)(H){sub 2}(TPPTS){sub 2}]CF{sub 3}SO{sub 3}. Reaction of trans-Ir(CO)ClL{sub 2} (L = TPPMS or TPPTS) with excess L in H{sub 2}O produces [Ir(CO)L{sub 3}]Cl, while no reaction occurs in DMSO, [Ir(CO){sub 3}(TPPMS){sub 2}]Cl reacts irreversibly with TPPMS in H{sub 2}O to produce [Ir(CO){sub 2}-(TPPMS){sub 3}]Cl.« less

The influence of NH3 on NO2 conversion in a dc corona discharge in N2:O2:CO2:NO2:NH3 mixture

NASA Astrophysics Data System (ADS)

Dors, Mirosław; Mizeraczyk, Jerzy; Czech, Tadeusz; Konieczka, Jerzy

1996-10-01

The aim of this paper is to investigate the influence of NH3 additive (540-1470 ppm) on the conversion of NO2 and the creation of NO and N2O in a mixture of N2:O2:CO2: NO2:NH3 subjected to the so-called direct current (dc) corona discharge. The dc corona discharge was generated in a needle-to-plate reactor. Seven positively polarized needles were used as one electrode and a stainless steel plate as the other. The time-averaged discharge current was varied from 0 to 7 mA. It was found that the dc corona discharge decomposed NO2 and produced NO and N2O. The reduction of NO2 was higher without NH3 additive if the residence time of the operating gas was relatively short. However, in a longer corona discharge processing the NH3 additive may be useful for reduction of NO2.

Interaction of SO2 and CO with the Ti2O3(101¯2) surface

NASA Astrophysics Data System (ADS)

Smith, Kevin E.; Henrich, Victor E.

1985-10-01

The interaction of sulfur dioxide with the nearly perfect (101¯2) surface of the corundum transition-metal oxide Ti2O3 has been studied using ultraviolet and x-ray photoemission spectroscopies and low-energy electron diffraction. The reaction of SO2 with Ti2O3 is found to be extremely vigorous, with SO2 adsorbing dissociatively and catalyzing the complete oxidation of the surface to TiO2 and TiS2. This result is significant since exposure to large amounts of O2 does not result in the production of large amounts of TiO2 at the Ti2O3 surface. Dissociative adsorption of SO2 continues for exposures up to at least 104 L (1 L=10-6Torr sec). The reaction is accompanied by large scale surface disorder and by an increase in the work function of 1.32 eV. In contrast, CO adsorbs molecularly for exposures >=105 L, with an extramolecular relaxation-polarization shift of 3.0 eV. For CO exposures <=104 L, the chemisorption mechanism is tentatively identified as dissociative adsorption at defect sites. Inclusive of this study, the interaction of four oxygen-containing molecules (SO2, CO, H2O, and O2) with Ti2O3(101¯2) surfaces has been studied, and their behavior is compared and trends isolated with a view to understanding the oxidation of Ti2O3.

Thermal decomposition of europium sulfates Eu2(SO4)3·8H2O and EuSO4

NASA Astrophysics Data System (ADS)

Denisenko, Yu. G.; Khritokhin, N. A.; Andreev, O. V.; Basova, S. A.; Sal'nikova, E. I.; Polkovnikov, A. A.

2017-11-01

Reactions of europium sulfates Eu2(SO4)3·8H2O and EuSO4 complete decomposition were studied by Simultaneous Thermal Analysis. It was revealed that one-step dehydratation of Eu2(SO4)3·8H2O crystallohydrate is accompanied by the formation of amorphous anhydrous europium sulfate Eu2(SO4)3. Crystallization of amorphous europium (III) sulfate occurs at 381.1 °C (in argon) and 391.3 °C (in air). The average enthalpy values for dehydratation reaction of Eu2(SO4)3·8H2O (ΔH° = 141.1 kJ/mol), decomposition reactions of Eu2(SO4)3 (ΔH = 463.1 kJ/mol), Eu2O2SO4 (ΔH = 378.4 kJ/mol) and EuSO4 (ΔH = 124.1 kJ/mol) were determined. The step process mechanisms of thermal decomposition of europium (III) sulfate in air and europium (II) sulfate in inert atmosphere were established and justified. The kinetic parameters of complete thermal decomposition of europium (III) sulfate octahydrate were calculated by Kissinger model. The standard enthalpies of compound formation were calculated using thermal effects and formation enthalpy data for binary compounds.

17O excess transfer during the NO2 + O3 → NO3 + O2 reaction.

PubMed

Berhanu, Tesfaye Ayalneh; Savarino, Joël; Bhattacharya, S K; Vicars, Willliam C

2012-01-28

The ozone molecule possesses a unique and distinctive (17)O excess (Δ(17)O), which can be transferred to some of the atmospheric molecules via oxidation. This isotopic signal can be used to trace oxidation reactions in the atmosphere. However, such an approach depends on a robust and quantitative understanding of the oxygen transfer mechanism, which is currently lacking for the gas-phase NO(2) + O(3) reaction, an important step in the nocturnal production of atmospheric nitrate. In the present study, the transfer of Δ(17)O from ozone to nitrate radical (NO(3)) during the gas-phase NO(2) + O(3) → NO(3) + O(2) reaction was investigated in a series of laboratory experiments. The isotopic composition (δ(17)O, δ(18)O) of the bulk ozone and the oxygen gas produced in the reaction was determined via isotope ratio mass spectrometry. The Δ(17)O transfer function for the NO(2) + O(3) reaction was determined to be: Δ(17)O(O(3)∗) = (1.23 ± 0.19) × Δ(17)O(O(3))(bulk) + (9.02 ± 0.99). The intramolecular oxygen isotope distribution of ozone was evaluated and results suggest that the excess enrichment resides predominantly on the terminal oxygen atoms of ozone. The results obtained in this study will be useful in the interpretation of high Δ(17)O values measured for atmospheric nitrate, thus leading to a better understanding of the natural cycling of atmospheric reactive nitrogen. © 2012 American Institute of Physics

Synergistic effect among Cl2, SO2 and NO2 in their heterogeneous reactions on gamma-alumina

NASA Astrophysics Data System (ADS)

Huang, Zhenling; Zhang, Zhaohui; Kong, Weiheng; Feng, Shuo; Qiu, Ye; Tang, Siqun; Xia, Chuanqin; Ma, Lingling; Luo, Min; Xu, Diandou

2017-10-01

Severe haze in China has been a global concern in recent years. Most studies about the mechanism of haze formation mare only focused on the heterogeneous reactions of SO2 and NO2 on mineral aerosols. However, little is known about the role of molecular chlorine (Cl2) in those reactions. Here, we investigated the heterogeneous uptake of Cl2, SO2 and NO2 on γ-Al2O3 particles under different conditions using a quartz-based flow reactor. We found that the existence of γ-Al2O3 seed aerosols significantly promotes the formation of secondary chloride, sulfate and nitrate aerosols, and Cl2, NO2 and SO2 have synergistic effects when they react on γ-Al2O3 surface under humid condition. The results also shows that Cl2 can promote the formation of secondary sulfate and nitrate aerosols on γ-Al2O3 surface. Moreover, Cl2 is much easier to react with the surface of γ-Al2O3 and form secondary Cl- aerosol when comparing with NO2 and SO2, suggesting that Cl2 is of great importance in atmospheric chemistry, it has the potential to alter the surface properties (e.g., chemical composition and fraction) of mineral aerosol, enhance the production of secondary inorganic aerosols in the troposphere, and thus cause adverse effects on the climate and human health.

Syntheses, crystal structures and optical spectroscopy of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kazmierczak, Karolina; Hoeppe, Henning A., E-mail: henning@ak-hoeppe.d

2011-05-15

The lanthanide sulphate octahydrates Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and the respective tetrahydrate Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O were obtained by evaporation of aqueous reaction mixtures of trivalent rare earth oxides and sulphuric acid at 300 K. Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) crystallise in space group C2/c (Z=4, a{sub Ho}=13.4421(4) A, b{sub Ho}=6.6745(2) A, c{sub Ho}=18.1642(5) A, {beta}{sub Ho}=102.006(1) A{sup 3} and a{sub Tm}=13.4118(14) A, b{sub Tm}=6.6402(6) A, c{sub Tm}=18.1040(16) A, {beta}{sub Tm}=101.980(8) A{sup 3}), Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O adopts space group P2{sub 1}/n (a=13.051(3) A, b=7.2047(14) A, c=13.316(3) A, {beta}=92.55(3) A{sup 3}). The vibrationalmore » and optical spectra of Ho{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O are also reported. -- Graphical abstract: In the lanthanide sulphate octahydrates the cations form slightly undulated layers. Between the layers are voids in which sulphate tetrahedra and water molecules are located. The holmium compound exhibits an Alexandrite effect. Display Omitted Highlights: {yields} Determination of the optimum conditions for the growth of single-crystals of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O. {yields} Single-crystal structure elucidation of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) including hydrogen bonds. {yields} Single-crystal structure determination of Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O including hydrogen bonds. {yields} UV-vis spectra of Ho{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O recorded and interpreted: Assignation of bands and clarification of the Alexandrite effect of the Ho compound. {yields} IR and Raman spectra of Ln{sub 2}(SO{sub 4}){sub 3}.8H{sub 2}O (Ln=Ho, Tm) and Pr{sub 2}(SO{sub 4}){sub 3}.4H{sub 2}O recorded and interpreted.« less

Ceramic oxide reactions with V2O5 and SO3

NASA Technical Reports Server (NTRS)

Jones, R. L.; Williams, C. E.

1985-01-01

Ceramic oxides are not inert in combustion environments, but can react with, inter alia, SO3, and Na2SO4 to yield low melting mixed sulfate eutectics, and with vanadium compounds to produce vanadates. Assuming ceramic degradation to become severe only when molten phases are generated in the surface salt (as found for metallic hot corrosion), the reactivity of ceramic oxides can be quantified by determining the SO3 partial pressure necessary for molten mixed sulfate formation with Na2SO3. Vanadium pentoxide is an acidic oxide that reacts with Na2O, SO3, and the different ceramic oxides in a series of Lux-Flood type of acid-base displacement reactions. To elucidate the various possible vanadium compound-ceramic oxide interactions, a study was made of the reactions of a matrix involving, on the one axis, ceramix oxides of increasing acidity, and on the other axis, vanadium compounds of increasing acidity. Resistance to vanadium compound reaction increased as the oxide acidity increased. Oxides more acidic than ZrO2 displaced V2O5. Examination of Y2O3- and CeO2-stabilized ZrO2 sintered ceramics which were degraded in 700 C NaVO3 has shown good agreement with the reactions predicted above, except that the CeO2-ZrO2 ceramic appears to be inexplicably degraded by NaVO3.

Long path monitoring of tropospheric O3, NO2, H2CO and SO2

NASA Technical Reports Server (NTRS)

Vandaele, A. C.; Carleer, M.; Colin, R.; Simon, P. C.

1994-01-01

Concentrations of tropospheric O3, NO2, H2CO, and SO2 have been measured on the Campus of the 'Universite Libre de Bruxelles' on a routine basis since October 1990. The long path system consists of a source lamp, a first 30 cm f/8 Cassegrain type telescope which collimates the light onto a slightly parabolic mirror placed on the roof of a building situated 394 m away from the laboratory. The light is sent back into a second 30 cm Cassegrain telescope. This telescope has been modified so that the output beam is a 5 cm diameter parallel beam. This beam is then focused onto the entrance aperture of the BRUKER IFS120HR fourier transform spectrometer. The two telescopes are mounted on alignment devices and the external mirror is equipped with a driving system operated from the laboratory. The choice of the light source (either a 1000 W high pressure 'ozone free' xenon lamp or a 250 W tungsten filament) and of the detector (either a solar blind UV-diode or a silicon diode) depended on the spectral region studied. These regions lie respectively from 26,000 cm(exp -1) to 30,000 cm(exp -1) (260-380 nm) and from 14,000 cm(exp -1) to 30,000 cm(exp -1) (330-700 nm). The spectra have been recorded at the resolution of 16 cm(exp -1) and with a dispersion of 7.7 cm(exp -1). They have been measured during the forward and the backward movements of the mobile mirror, in double sided mode; each spectrum is an average of 2000 scans. The time required to record a spectrum is about 45 minutes. The shape of the raw spectra in the two investigated regions are represented.

X-ray investigation of molten crystal hydrates H2SO4(nH2O) and HNO3(nH2O)

NASA Technical Reports Server (NTRS)

Romanova, A. V.; Skryshevskiy, A. F.

1979-01-01

Integral analysis of the intensity of the electron density distribution curve in molten crystal hydrates provided by X-ray analysis, permits the following conclusions on the structure of the complex SO and NO ions, and the short-range order in the structure of the solution. The SO4 ion in the solution has a tetrahedral structure with an S to O distance equal to 1.5 A. For the NO3 in the solution, a planar triangular shape is probable, with an N to O distance equal to 1.2 A. Preferential distances between each of the oxygens of the SO ion and the nearest molecules of water proved near to the corresponding distances in solid crystal hydrates. For an (H2SO4)(H2O) solution, the average number of water molecules surrounding each oxygen atom of the SO4 (--) ion was on the order of 1.3 molecules. Hence the preferential distances between the water molecules and the oxygen atoms of the SO ion, and the preference of their mutual position, correspond to the fixed position of these same elements of the structure in the solid crystal hydrate.

The promoting effect of CeO2@Ce-O-P multi-core@shell structure on SO2 tolerance for selective catalytic reduction of NO with NH3 at low temperature

NASA Astrophysics Data System (ADS)

Yao, Weiyuan; Liu, Yue; Wu, Zhongbiao

2018-06-01

A series of CeO2@Ce-O-P "multi-core@shell" catalysts were synthesized in this paper for selective catalytic reduction (SCR) of NO with NH3. The experimental results had showed that CeO2@Ce-O-P-30:3 yielded best SO2 tolerance of an over 70% deNOx efficiency at 250 °C in the presence of 100 ppm SO2 for 20 h, which was much higher compared to pure Ce-O-P and CeO2 samples. Further characterization results indicated that Ce-O-P coating layer could somewhat inhibit sulfur depositing on the catalysts during SCR reaction in the presence of SO2, thereby protecting the active sites from SO2 poisoning. Especially, O2-TPD results illustrated that a great amount of active oxygen species were retained on used CeO2@Ce-O-P catalyst after a long term reaction. The synergetic effect of "multi-core@shell" structure could be attributed to such enhanced performances. The "core" CeO2 devoted abundant active oxygen sites to fulfill the SCR reaction. And the "shell" Ce-O-P could not only provide acid sites, but also protect the active oxygen species by avoiding the over-adsorption of SO2 on the catalyst. This work could provide a new way to increase the sulfur resistance for low temperature SCR catalysts.

Nocturnal Vertical Gradients of O3, NO2, NO3, HONO, HCHO, and SO2 in Los Angeles, CA, during CalNex 2010

NASA Astrophysics Data System (ADS)

Tsai, J.; Pikelnaya, O.; Hurlock, S. C.; Wong, K.; Cheung, R.; Haman, C. L.; Lefer, B. L.; Stutz, J.

2010-12-01

Nocturnal chemistry, through the conversion and removal of air pollutants, plays an important role in determining the initial condition for photochemistry during the following day. In the stable nocturnal boundary layer (NBL) the interplay between suppressed vertical mixing and surface emissions of NOx and VOCs can result in pronounced vertical trace gas profiles. The resulting altitude dependence of nocturnal chemistry makes the interpretation of ground observations challenging. In particular, the quantification of the nocturnal loss of NOx, due to NO3 and N2O5 chemistry, requires observations throughout the entire vertical extent of the NBL. The formation of daytime radical precursors, such as HONO, is also altitude dependent. An accurate assessment of their impact on daytime chemistry requires measurements of their profiles during the night and morning. Here we present observations from the CalNex-LA experiment, which took place from May 15 to June 15, 2010 on the east side of the Los Angeles Basin, CA. A Long-Path Differential Optical Absorption Spectrometer (LP-DOAS) was set up on the roof of the Millikan library (265 m asl, 35m agl) on the campus of the California Institute of Technology. Four retroreflector arrays were mounted about 5 -7 km North-East of the instrument at 310m, 353m, 487m and 788 m asl. The vertical profiles of NO3, HONO, NO2, O3, HCHO, and SO2 were retrieved at altitude intervals of 35-78m, 78-121m, 121-255m and 255-556m above the ground. During many nights vertical gradients were observed, with elevated NO2 and HONO concentrations near the surface and larger ozone and NO3 concentrations aloft. Simultaneous ceilometer observations of the NBL structure show the impact of meteorology on the vertical trace gas distributions. We will discuss the consequences of trace gases gradients on the nocturnal NOx budget.

Synergistic reaction between SO2 and NO2 on mineral oxides: a potential formation pathway of sulfate aerosol.

PubMed

Liu, Chang; Ma, Qingxin; Liu, Yongchun; Ma, Jinzhu; He, Hong

2012-02-07

Sulfate is one of the most important aerosols in the atmosphere. A new sulfate formation pathway via synergistic reactions between SO(2) and NO(2) on mineral oxides was proposed. The heterogeneous reactions of SO(2) and NO(2) on CaO, α-Fe(2)O(3), ZnO, MgO, α-Al(2)O(3), TiO(2), and SiO(2) were investigated by in situ Diffuse Reflectance Infrared Fourier Transform Spectroscopy (in situ DRIFTS) at ambient temperature. Formation of sulfate from adsorbed SO(2) was promoted by the coexisting NO(2), while surface N(2)O(4) was observed as the crucial oxidant for the oxidation of surface sulfite. This process was significantly promoted by the presence of O(2). The synergistic effect between SO(2) and NO(2) was not observed on other mineral particles (such as CaCO(3) and CaSO(4)) probably due to the lack of the surface reactive oxygen sites. The synergistic reaction between SO(2) and NO(2) on mineral oxides resulted in the formation of internal mixtures of sulfate, nitrate, and mineral oxides. The change of mixture state will affect the physicochemical properties of atmospheric particles and therefore further influence their environmental and climate effects.

Diode laser-based cavity ring-down instrument for NO3, N2O5, NO, NO2 and O3 from aircraft

NASA Astrophysics Data System (ADS)

Wagner, N. L.; Dubé, W. P.; Washenfelder, R. A.; Young, C. J.; Pollack, I. B.; Ryerson, T. B.; Brown, S. S.

2011-03-01

This article presents a diode laser based, cavity ring-down spectrometer for simultaneous in situ measurements of four nitrogen oxide species, NO3, N2O5, NO, NO2, as well as O3, designed for deployment on aircraft. The instrument measures NO3 and NO2 by optical extinction at 662 nm and 405 nm, respectively; N2O5 is measured by thermal conversion to NO3, while NO and O3 are measured by chemical conversion to NO2. The instrument has several advantages over previous instruments developed by our group for measurement of NO2, NO3 and N2O5 alone, based on a pulsed Nd:YAG and dye laser. First, the use of continuous wave diode lasers reduces the requirements for power and weight and eliminates hazardous materials. Second, detection of NO2 at 405 nm is more sensitive than our previously reported 532 nm instrument, and does not have a measurable interference from O3. Third, the instrument includes chemical conversion of NO and O3 to NO2 to provide measurements of total NOx (= NO + NO2) and Ox (= NO2 + O3) on two separate channels; mixing ratios of NO and O3 are determined by subtraction of NO2. Finally, all five species are calibrated against a single standard based on 254 nm O3 absorption to provide high accuracy. Disadvantages include an increased sensitivity to water vapor on the 662 nm NO3 and N2O5 channels and a modest reduction in sensitivity for these species compared to the pulsed laser instrument. The measurement precision for both NO3 and N2O5 is below 1 pptv (2σ, 1 s) and for NO, NO2 and O3 is 170, 46, and 56 pptv (2σ, 1 s) respectively. The NO and NO2 measurements are less precise than research-grade chemiluminescence instruments. However, the combination of these five species in a single instrument, calibrated to a single analytical standard, provides a complete and accurate picture of nighttime nitrogen oxide chemistry. The instrument performance is demonstrated using data acquired during a recent field campaign in California.

DSCOVR_EPIC_L2_O3SO2AI_01

Atmospheric Science Data Center

2018-06-29

... dioxide (SO2) from volcanic plumes, scene reflectivity, and aerosol index (AI), retrieved from the ultraviolet (UV) measurements of DSCOVR ... Access:   Order Data Parameters:  Aerosol Index (AI) Reflectivity at 340 nm Vertical Column of Ozone (O3) ...

Diode laser-based cavity ring-down instrument for NO3, N2O5, NO, NO2 and O3 from aircraft

NASA Astrophysics Data System (ADS)

Wagner, N. L.; Dubé, W. P.; Washenfelder, R. A.; Young, C. J.; Pollack, I. B.; Ryerson, T. B.; Brown, S. S.

2011-06-01

This article presents a diode laser-based, cavity ring-down spectrometer for simultaneous in situ measurements of four nitrogen oxide species, NO3, N2O5, NO, NO2, as well as O3, designed for deployment on aircraft. The instrument measures NO3 and NO2 by optical extinction at 662 nm and 405 nm, respectively; N2O5 is measured by thermal conversion to NO3, while NO and O3 are measured by chemical conversion to NO2. The instrument has several advantages over previous instruments developed by our group for measurement of NO2, NO3 and N2O5 alone, based on a pulsed Nd:YAG and dye laser. First, the use of continuous wave diode lasers reduces the requirements for power and weight and eliminates hazardous materials. Second, detection of NO2 at 405 nm is more sensitive than our previously reported 532 nm instrument, and does not have a measurable interference from O3. Third, the instrument includes chemical conversion of NO and O3 to NO2 to provide measurements of total NOx (= NO + NO2) and Ox (= NO2 + O3) on two separate channels; mixing ratios of NO and O3 are determined by subtraction of NO2. Finally, all five species are calibrated against a single standard based on 254 nm O3 absorption to provide high accuracy. Disadvantages include an increased sensitivity to water vapor on the 662 nm NO3 and N2O5 channels and a modest reduction in sensitivity for these species compared to the pulsed laser instrument. The in-flight detection limit for both NO3 and N2O5 is 3 pptv (2 σ, 1 s) and for NO, NO2 and O3 is 140, 90, and 120 pptv (2 σ, 1 s) respectively. Demonstrated performance of the instrument in a laboratory/ground based environment is better by approximately a factor of 2-3. The NO and NO2 measurements are less precise than research-grade chemiluminescence instruments. However, the combination of these five species in a single instrument, calibrated to a single analytical standard, provides a complete and accurate picture of nighttime nitrogen oxide chemistry. The

JOINT ACTION OF O3 AND SO2 IN MODIFYING PLANT GAS EXCHANGE

EPA Science Inventory

The joint action of O3 and SO2 stress on plants was investigated. Gas exchange measurements of O3, SO2, and H2O vapor were made for garden pea. Plants were grown under controlled environments; O3, SO2, H2O vapor fluxes were evaluated with a whole-plant gas exchange chamber using ...

Dynamic investigation of the role of the surface sulfates in NO{sub x} reduction and SO{sub 2} oxidation over V{sub 2}O{sub 5}-WO{sub 3}/TiO{sub 2} catalysts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Orsenigo, C.; Lietti, L.; Tronconi, E.

1998-06-01

Transient experiments performed over synthesized and commercial V{sub 2}O{sub 5}-WO{sub 3}/TiO{sub 2} catalysts during catalyst conditioning and during step changes of the operating variables (SO{sub 2} inlet concentration and temperature) show that conditioning of the catalyst is required to attain significant and reproducible steady-state data in both the reduction of NO{sub x} and the oxidation of SO{sub 2}. The response time of conditioning for NO{sub x} reduction is of a few hours and that for SO{sub 2} oxidation is of several hours. Fourier transform infrared spectroscopy temperature programmed decomposition, and thermogravimetric measurements showed that catalyst conditioning is associated with amore » slow process of buildup of sulfates: the different characteristic conditioning times observed in the reduction of NO{sub x} and in the oxidation of SO{sub 2} suggest that the buildup of sulfates occurs first at the vanadyl sites and later on at the exposed titania surface. Formation of sulfates at or near the vanadyl sites increases the reactivity in the de-NO{sub x} reaction, possibly due to the increase in the Broensted and Lewis acidity of the catalyst, whereas the titania surface acts as SO{sub 3} acceptor and affects the outlet SO{sub 3} concentration during catalyst conditioning for the SO{sub 2} oxidation reaction. The response time to step changes in SO{sub 2} concentration and temperature is of a few hours in the case of SO{sub 2} oxidation and much shorter in the case of NO{sub x} reduction. The different time responses associated with conditioning and with step changes in the settings of the operating variables have been rationalized in terms of the different extent of perturbation of the sulfate coverage experienced by the catalyst.« less

Effect of Na poisoning catalyst (V2O5-WO3/TiO2) on denitration process and SO3 formation

NASA Astrophysics Data System (ADS)

Xiao, Haiping; Chen, Yu; Qi, Cong; Ru, Yu

2018-03-01

This paper aims to study the effect of alkali metal sodium (Na) poisoning on the performance of the Selective Catalytic Reduction (SCR) catalyst. The result showed that Na2SO4 poisoning leads to a reduced denitration rate of the SCR catalyst and an increase in the SO3 generation rate. Na2O poisoning leads to a significant reduction in the denitration rate of the SCR catalyst and marginally improves the formation of SO3. The maximum of the SO3 generation rate for a Na2SO4-poisoned catalyst reached 1.35%, whereas it was only 0.85% for the SCR catalyst. When the SO2 was contained in flue gas, the denitration rate for the Na2O-poisoned catalyst clearly increased by more than 28%. However, the effect of SO2 on the Na2SO4-poisoned catalyst was very slight. The denitration rate of the SCR catalyst decreased with an increase in the Na content. The BET and XRD results showed that Na poisoning of the catalyst decreased the number of acid sites, the reducibility of the catalyst, the surface area, and pore volume. The H2-TPR and NH3-TPD results show that Na decreases the number of acid sites and the reducibility of the catalyst. The FT-IR and XPS results showed that Na2O poisoning led to the decrease of V5+dbnd O bonds and the consumptions of oxygen atoms. Na2SO4 poisoning can improve surface adsorbed oxygen, which was beneficial for the SO2-SO3 conversion reaction.

Influence of the Organic Species and Oxoanion in the Synthesis of two Uranyl Sulfate Hydrates, (H 3 O) 2 [(UO 2 ) 2 (SO 4 ) 3 ­(H 2 O)]·7H 2 O and (H 3 O) 2 [(UO 2 ) 2 (SO 4 ) 3 (H 2 O)]·4H 2 O, and a Uranyl Selenate-Selenite [C 5 H 6 N][(UO 2 )(SeO 4 )(HSeO 3 )

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jouffret, Laurent J.; Wylie, Ernest M.; Burns, Peter C.

2012-08-08

Two uranyl sulfate hydrates, (H3O)2[(UO2)2(SO4)3(H2O)]·7H2O (NDUS) and (H3O)2[(UO2)2(SO4)3(H2O)]·4H2O (NDUS1), and one uranyl selenate-selenite [C5H6N][(UO2)(SeO4)(HSeO3)] (NDUSe), were obtained and their crystal structures solved. NDUS and NDUSe result from reactions in highly acidic media in the presence of L-cystine at 373 K. NDUS crystallized in a closed vial at 278 K after 5 days and NDUSe in an open beaker at 278 K after 2 weeks. NDUS1 was synthesized from aqueous solution at room temperature over the course of a month. NDUS, NDUS1, and NDUSe crystallize in the monoclinic space group P21/n, a = 15.0249(4) Å,b = 9.9320(2) Å, c = 15.6518(4)more » Å, β = 112.778(1)°, V = 2153.52(9) Å3,Z = 4, the tetragonal space group P43212, a = 10.6111(2) Å,c = 31.644(1) Å, V = 3563.0(2) Å3, Z = 8, and in the monoclinic space group P21/n, a = 8.993(3) Å, b = 13.399(5) Å, c = 10.640(4) Å,β = 108.230(4)°, V = 1217.7(8) Å3, Z = 4, respectively.The structural units of NDUS and NDUS1 are two-dimensional uranyl sulfate sheets with a U/S ratio of 2/3. The structural unit of NDUSe is a two-dimensional uranyl selenate-selenite sheets with a U/Se ratio of 1/2. In-situ reaction of the L-cystine ligands gives two distinct products for the different acids used here. Where sulfuric acid is used, only H3O+ cations are located in the interlayer space, where they balance the charge of the sheets, whereas where selenic acid is used, interlayer C5H6N+ cations result from the cyclization of the carboxyl groups of L-cystine, balancing the charge of the sheets.« less

Application of V2O5/WO3/TiO2 for Resistive-Type SO2 Sensors

PubMed Central

Izu, Noriya; Hagen, Gunter; Schönauer, Daniela; Röder-Roith, Ulla; Moos, Ralf

2011-01-01

A study on the application of V2O5/WO3/TiO2 (VWT) as the sensitive material for resistive-type SO2 sensor was conducted, based on the fact that VWT is a well-known catalyst material for good selective catalytic nitrogen oxide reduction with a proven excellent durability in exhaust gases. The sensors fabricated in this study are planar ones with interdigitated electrodes of Au or Pt. The vanadium content of the utilized VWT is 1.5 or 3.0 wt%. The resistance of VWT decreases with an increasing SO2 concentration in the range from 20 ppm to 5,000 ppm. The best sensor response to SO2 occurs at 400 °C using Au electrodes. The sensor response value is independent on the amount of added vanadium but dependent on the electrode materials at 400 °C. These results are discussed and a sensing mechanism is discussed. PMID:22163780

Magneto-optical investigation of MgSO3·6H2O with polarized light

NASA Astrophysics Data System (ADS)

Petkova, P.

2017-10-01

The crystals of magnesium sulphite hexahydrate (MgSO3·6H2O) belong to point group C3 (no center of symmetry). They possess gyrotropy and nonlinear optical properties. The refractive index no and ne, the angle of Faraday rotation φ(λ), the Verdet constant V(λ), the magneto-optic anomaly factor γ(λ) and the density of oscillators N of MgSO3·6H2O single crystals have been studied in the present work. The investigations were carried out in the spectral range 300 - 800 nm with linear polarized light E ⃗ ⊥ c ̅ , E ⃗ | | c ̅ (c ̅ is the optical axis of MgSO3·6H2O) propagated in the direction (10 1 ̅ 0) .

Polymorphism in Bi2(SO4)3

NASA Astrophysics Data System (ADS)

Subban, Chinmayee V.; Rousse, Gwenaëlle; Courty, Matthieu; Barboux, Philippe; Tarascon, Jean-Marie

2014-12-01

A new polymorph of Bi2(SO4)3 was prepared by reaction of LiBiO2 with H2SO4 and its crystal structure was solved from X-ray powder diffraction. This new polymorph crystallizes in C2/c space group with lattice parameters a = 17.3383(3) Å, b = 6.77803(12) Å, c = 8.30978(13) Å, β = 101.4300(12)°. Bi2(SO4)3 presents a layered structure made of SO4 sulfate groups and signs of stereochemically active Bi3+ lone pairs. The new Bi2(SO4)3 absorbs water to form Bi2(H2O)2(SO4)2(OH)2 through an intermediate Bi2O(OH)2SO4 phase, and the transition is reversible when heated under vacuum.

Numerical Study of the Simultaneous Oxidation of NO and SO2 by Ozone

PubMed Central

Li, Bo; Zhao, Jinyang; Lu, Junfu

2015-01-01

This study used two kinetic mechanisms to evaluate the oxidation processes of NO and SO2 by ozone. The performance of the two models was assessed by comparisons with experimental results from previous studies. The first kinetic mechanism was a combined model developed by the author that consisted of 50 species and 172 reactions. The second mechanism consisted of 23 species and 63 reactions. Simulation results of both of the two models show under predictions compared with experimental data. The results showed that the optimized reaction temperature for NO with O3 ranged from 100~200 °C. At higher temperatures, O3 decomposed to O2 and O, which resulted in a decrease of the NO conversion rate. When the mole ratio of O3/NO was greater than 1, products with a higher oxidation state (such as NO3, N2O5) were formed. The reactions between O3 and SO2 were weak; as such, it was difficult for O3 to oxidize SO2. PMID:25642689

A study of Pd/SO4/ZrO2/Al2O3 catalysts in n-hexane isomerization

NASA Astrophysics Data System (ADS)

Dzhikiya, O. V.; Smolikov, M. D.; Kazantsev, K. V.; Yablokova, S. S.; Kireeva, T. V.; Paukshtis, E. A.; Gulyaeva, T. I.; Belyi, A. S.

2017-08-01

The effect of palladium concentration in a range from 0.02 to 1.6 wt.% on characteristics of n-hexane isomerization was studied. The (O2-Hchem) titration and O2 chemisorption study revealed that palladium in Pd/SO4/ZrO2/Al2O3 systems adsorbs hydrogen in a ratio H/Pds = 1.13-1.65 at./at. Investigation of the charge state of the metal by IR spectroscopy of adsorbed CO showed the presence of both the metallic (Pd0) and charged palladium species. Pd/SO4/ZrO2/Al2O3 catalysts with charged palladium atoms exhibit high activity and selectivity in n-hexane isomerization.

CAIRPOL CAIRCLIP O3-NO2

EPA Science Inventory

The CairPol CairClip O₃-NO₂ is a lightweight, portable sensor for measuring ozone (O₃) and nitrogen dioxide (NO₂) in parts per billion (ppb) or micrograms per cubic meter (µg/m³) in applications such as personal exposure and ...

40 CFR Figure C-1 to Subpart C of... - Suggested Format for Reporting Test Results for Methods for SO 2, CO, O 3, NO 2

Code of Federal Regulations, 2011 CFR

2011-07-01

... Results for Methods for SO 2, CO, O 3, NO 2 C Figure C-1 to Subpart C of Part 53 Protection of Environment... Pt. 53, Subpt. C, Fig. C-1 Figure C-1 to Subpart C of Part 53—Suggested Format for Reporting Test... Difference Table C-1 spec. Pass or fail Low 1 ____ ppm 2 to ____ ppm 3 4 5 6 Medium 1 ____ ppm 2 to ____ ppm...

40 CFR Figure C-1 to Subpart C of... - Suggested Format for Reporting Test Results for Methods for SO 2, CO, O 3, NO 2

Code of Federal Regulations, 2014 CFR

2014-07-01

... Results for Methods for SO 2, CO, O 3, NO 2 C Figure C-1 to Subpart C of Part 53 Protection of Environment... Pt. 53, Subpt. C, Fig. C-1 Figure C-1 to Subpart C of Part 53—Suggested Format for Reporting Test... Difference Table C-1 spec. Pass or fail Low 1 ____ ppm 2 to ____ ppm 3 4 5 6 Medium 1 ____ ppm 2 to ____ ppm...

40 CFR Figure C-1 to Subpart C of... - Suggested Format for Reporting Test Results for Methods for SO 2, CO, O 3, NO 2

Code of Federal Regulations, 2012 CFR

2012-07-01

... Results for Methods for SO 2, CO, O 3, NO 2 C Figure C-1 to Subpart C of Part 53 Protection of Environment... Pt. 53, Subpt. C, Fig. C-1 Figure C-1 to Subpart C of Part 53—Suggested Format for Reporting Test... Difference Table C-1 spec. Pass or fail Low 1 ____ ppm 2 to ____ ppm 3 4 5 6 Medium 1 ____ ppm 2 to ____ ppm...

40 CFR Figure C-1 to Subpart C of... - Suggested Format for Reporting Test Results for Methods for SO 2, CO, O 3, NO 2

Code of Federal Regulations, 2010 CFR

2010-07-01

... Results for Methods for SO 2, CO, O 3, NO 2 C Figure C-1 to Subpart C of Part 53 Protection of Environment... Pt. 53, Subpt. C, Fig. C-1 Figure C-1 to Subpart C of Part 53—Suggested Format for Reporting Test... Difference Table C-1 spec. Pass or fail Low 1 ____ ppm 2 to ____ ppm 3 4 5 6 Medium 1 ____ ppm 2 to ____ ppm...

40 CFR Figure C-1 to Subpart C of... - Suggested Format for Reporting Test Results for Methods for SO 2, CO, O 3, NO 2

Code of Federal Regulations, 2013 CFR

2013-07-01

... Results for Methods for SO 2, CO, O 3, NO 2 C Figure C-1 to Subpart C of Part 53 Protection of Environment... Pt. 53, Subpt. C, Fig. C-1 Figure C-1 to Subpart C of Part 53—Suggested Format for Reporting Test... Difference Table C-1 spec. Pass or fail Low 1 ____ pPM 2 to ____ pPM 3 4 5 6 Medium 1 ____ pPM 2 to ____ pPM...

Kinetic studies of the reaction of the SO radical with NO2 and ClO from 210 to 363 K

NASA Technical Reports Server (NTRS)

Brunning, J.; Stief, L. J.

1986-01-01

The rates of the reactions of the SO radical with NO2 and ClO (significant in the upper atmosphere of earth and Venus) were determined in a discharge flow system near 1 torr pressure with detection of radical and molecular species using collision-free sampling mass spectrometry. The rate constants were obtained from the decay of SO radicals in the presence of an excess of NO2 and ClO. The NO2 reaction was examined between 210 and 363 K and found to be temperature invariant: SO + NO2 yields SO2 + NO; k1 = (1.37 + or - 0.10) x 10 to the -11th cu cm/s. In addition, the ClO reaction was observed to be independent of temperature between 248 and 363 K: SO + ClO yields SO2 + Cl; k2 = (3.22 + or - 0.48) x 10 to the -11th cu cm/s. A comparison was made with previous investigations of these reactions at room temperature and with other radical-radical reactions involving SO or ClO.

MnFe{sub 2}O{sub 4} as a gas sensor towards SO{sub 2} and NO{sub 2} gases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rathore, Deepshikha, E-mail: deep.nano@gmail.com; Mitra, Supratim

2016-05-06

The chemical co-precipitation method was used to synthesize MnFe{sub 2}O{sub 4} nanoparticles. Single cubic phase formation of nanoparticles was confirmed by X-ray diffraction technique. The average particle size of MnFe{sub 2}O{sub 4} nanoparticles was found to be 10.7 nm using Scherrer formula. The ultrafine powder of MnFe{sub 2}O{sub 4} nanoparticles was pressed to design pellet of 10 mm diameter and 1mm thickness. Copper electrodes have been deposited on the surface of pellet using silver paste in the form of capacitor. Fabricated gas sensing device of MnFe{sub 2}O{sub 4} nanoparticles was tested towards SO{sub 2} and NO{sub 2} gases. Cole-Cole plot of MnFe{submore » 2}O{sub 4} was investigated with the help of electrochemical workstation. The performance of the sensors including sensitivity, response and recovery time was also determined. It was observed that the MnFe{sub 2}O{sub 4} nanoparticles are more sensible for NO{sub 2} gas as compared to SO{sub 2} gas.« less

Thermodynamic properties and crystal structure refinement of ferricopiapite, coquimbite, rhomboclase, and Fe2(SO4)3(H2O)5

USGS Publications Warehouse

Majzlan, J.; Navrotsky, A.; McCleskey, R. Blaine; Alpers, Charles N.

2006-01-01

Enthalpies of formation of ferricopiapite [nominally Fe4.67(SO4)6(OH)2 (H2O)20]. coquimbite [Fe2(SO4)3(H2O)9], rhomboclase [(H3O)Fe(SO4)2 (H2O)3], and Fe2(SO4)3(H2O)5 were measured by acid (5 N HCl) solution calorimetry. The samples were characterized by wet chemical analyses and synchrotron powder X-ray diffraction (XRD). The refinement of XRD patterns gave lattice parameters, atomic positions, thermal factors, and occupancies of the sites. The calculated formulae differ slightly from the nominal compositions: Fe4.78(SO4)6 (OH)2.34(H2O)20.71 (ferricopiapite), (Fe1.47Al0.53)(SO4)3 (H2O)9.65 (coquimbite), (H3O)1.34Fe(SO4)2.17 (H2O)3.06 (rhomboclase), and Fe2(SO4)3 (H2O)5.03. All thermodynamic data are given per mole of these formulae. The measured standard enthalpies (in kJ/mol) of formation from the elements (crystalline Fe, Al, S, and ideal gases O2 and H2) at T = 298.15 K are -4115.8??4.1 [Fe2(SO4)3 (H2O)5.03], -12045.1??9.2 (ferricopiapite), -5738.4??3.3 (coquimbite), and -3201.1??2.6 (rhomboclase). Standard entropy (S??) was estimated as a sum of entropies of oxide, hydroxide, and sulfate components. The estimated S?? (in J/mol.K) values for the iron sulfates are 488.2 [Fe2(SO4)3 (H2O)5.03], 1449.2 (ferricopiapite), 638.3 (coquimbite), and 380.1 (rhomboclase). The calculated Gibbs free energies of formation (in kJ/mol) are -3499.7??4.2 [Fe2(SO4)3 (H2O)5.03], -10089.8??9.3 (ferricopiapite), -4845.6??3.3 (coquimbite), and -2688.0??2.7 (rhomboclase). These results combined with other available thermodynamic data allow construction of mineral stability diagrams in the FeIII2(SO4)3-FeII SO4-H2O system. One such diagram is provided, indicating that the order of stability of ferric sulfate minerals with decreasing pH in the range of 1.5 to -0.5 is: hydronium jarosite, ferricopiapite, and rhomboclase. ?? 2006 E. Schweizerbart'sche Verlagsbuchhandlung.

Combined effects Na and SO2 in flue gas on Mn-Ce/TiO2 catalyst for low temperature selective catalytic reduction of NO by NH3 simulated by Na2SO4 doping

NASA Astrophysics Data System (ADS)

Zhou, Aiyi; Yu, Danqing; Yang, Liu; Sheng, Zhongyi

2016-08-01

A series of Mn-Ce/TiO2 catalysts were synthesized through an impregnation method and used for low temperature selective catalytic reduction (SCR) of NOx with ammonia (NH3). Na2SO4 was added into the catalyst to simulate the combined effects of alkali metal and SO2 in the flue gas. Experimental results showed that Na2SO4 had strong and fluctuant influence on the activity of Mn-Ce/TiO2, because the effect of Na2SO4 included pore occlusion and sulfation effect simultaneously. When Na2SO4 loading content increased from 0 to 1 wt.%, the SCR activities of Na2SO4-doped catalysts decreased greatly. With further increasing amount of Na2SO4, however, the catalytic activity increased gradually. XRD results showed that Na2SO4 doping could induce the crystallization of MnOx phases, which were also confirmed by TEM and SEM results. BET results showed that the surface areas decreased and a new bimodal mesoporous structure formed gradually with the increasing amount of Na2SO4. XPS results indicated that part of Ce4+ and Mn3+ were transferred to Ce3+ and Mn4+ due to the sulfation after Na2SO4 deposition on the surface of the catalysts. When the doped amounts of Na2SO4 increased, NH3-TPD results showed that the Lewis acid sites decreased and the Brønsted acid sites of Mn-Ce/TiO2 increased quickly, which could be considered as another reason for the observed changes in the catalytic activity. The decreased Mn and Ce atomic concentration, the changes of their oxidative states, and the variation in acidic properties on the surface of Na2SO4-doped catalysts could be the reasons for the fluctuant changes of the catalytic activity.

Influence of pH and ionic strength (NaCl/Na2SO4) on the reaction HO Cl/ClO- + NO2-

NASA Astrophysics Data System (ADS)

Marcellos da Rosa, M.; Zetzsch, C.

2003-04-01

Equilibria such as HOCl + NO_2^- leftrightarrow ClNO_2 + OH^- and ClNO_2 + H_2O leftrightarrow NO_3^- + 2H^+ + Cl^- play an important role in halogen activation in the troposphere. We studied the oxidation of NO_2^- by HOCl/ClO^- in aqueous phase by stopped-flow measurements at different ionic strengths (bidestilled water, 0.1M NaCl, 1.0M NaCl and 1.0M Na_2SO^4) at various pH values (4.0, 5.5, 6.2 and 10.0) at 293K. The experiments were performed using a SX.18MV Applied Photophysics spectrophotometer, observing the exponential decay of HOCl/ClO^- at λ = 290nm between 10ms and 100s. HOCl (pK_a= 7.50) was obtained by bubbling N_2 with 1% Cl_2 through bidestilled water. The pH of the aqueous solutions of HOCl was determined by a pH meter (CG820, Schott) with a glass electrode N6180 (calibrated with standard buffer solutions at pH = 3.0, 4.0, 7.0 and 10.0), and the pH values were adjusted by dropwise addition of HClO_4 or NaOH. The concentrations of HOCl (ɛHOCl (230nm) = 100M-1cm-1) ([HOCl] = 1.3mM - 10mM) and ClO- (ɛClO- (292nm) = 350 M-1cm-1) ([ClO^-] = 1.3mM - 5mM) were determined by UV spectrometry (Kontron UVIKON 860) at a resolution of 2 nm in 1 cm cells at various pH values. The concentration range of NO_2^- was between 5mM and 50mM. The following second-order rate constant kII were obtained at 293K at various pH values (in units of M-1s-1) in H_2O: pH 4.0, (5.6±0.3)\\cdot 10^3; pH 5.5, (5.0±0.4)\\cdot 10^3; pH 10.0, 3.9±0.4; in 0.1M NaCl: pH 5.5, (4.3±0.4)\\cdot 10^3; pH 10.0, 2.6±0.4; in 1.0M NaCl: pH 5.5, (4.0±0.3); pH 10.0, 0.7±0.2 and in 1.0M Na_2SO_4: pH 5.5, (3.0±0.3)\\cdot 10^3; pH 10.0, 1.9±0.4. There is a strong effect of the pH on the reaction HOCl/ClO^- + NO_2^-, as reflected in the ratio kII_a(pH 5.5, HOCl)/kII_b(pH 10.0, ClO^-): in H_2O (kII_a ˜ 1200 \\cdot kII_b), in 0.1M NaCl (kII_a ˜ 1900 \\cdot kII_b), in 1.0M NaCl (kII_a ˜ 5700 \\cdot kII_b) and in 1.0 M Na_2SO_4 (kII_a ˜ 1500 \\cdot kII_b). A mechanism for the oxidation of NO

SO2 Adsorption on CeO2(100) and CeO2(111)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mullins, David R.

2016-09-13

The adsorption and reaction of sulfur dioxide, SO2, was studied on oxidized and reduced CeOX(100) and compared to previous results on CeOX(111). SO2 adsorbs on oxidized CeO2(100) as sulfite, SO32-, at 200 K and sulfite is the only adsorbate observed on the surface at any temperature. The sulfite desorbs monotonically from 200 to 700 K. The adsorption and desorption of SO2 does not result in any change in the Ce4+ oxidation state. SO2 also adsorbs as sulfite on reduced CeO1.7(100) at 200 K. There is also a small amount of elemental sulfur, S0, formed. As the sample is heated themore » sulfite decomposes into sulfide, S2-. Roughly 25 % of the adsorbed S either desorbs or diffuses into the bulk of the reduced ceria. The decomposition, and resulting formation of S2- and O2-, re-oxidize some of the Ce3+ to Ce4+. Unlike what has been observed following the adsorption and reaction of many other molecules, the adsorption and reaction of SO2 is virtually identical on CeOX(100) and CeOX(111).« less

Influence of Water on the H2SO4 Yield from the Ozonolysis of 2,3-dimethyl-butene (TME) in Presence of SO2

NASA Astrophysics Data System (ADS)

Véronique, D.; Kukui, A.; Chen, H.; Mellouki, A.

2016-12-01

The influence of the water vapor content on the yield of H2SO4 from the ozonolysis of 2,3-dimethyl-butene (TME) in presence of SO2 was studied using laminar flow reactor coupled with Chemical Ionisation Mass Spectrometer (CIMS) for the H2SO4 monitoring within the range of H2O from 10 ppmv to 3×104 ppmv at different concentrations of TME, O3, SO2. The observed dependences of the H2SO4 yield on H2O concentration can be interpreted by assuming two different paths of the H2SO4 formation: 1) via the formation of SO3 in the reaction of Stabilized Criegee Intermediate (SCI) with SO2 (2a) followed by the reaction of SO3 with H2O (3) and 2) via the formation of stabilized secondary ozonide (SOZ) (2b) producing H2SO4 in the reaction with H2O (4a) in competition with the SOZ decomposition to other products (5): O3+TME => (CH3)2COO (1) (CH3)2COO + SO2 => SO3 (2a) => SOZ (2b) SO3 + H2O => H2SO4 (3) SOZ + H2O => H2SO4 (or SO3) (4a) SOZ + M => products (5) The yield of the SCI, SOZ and the rates of the SCI and SOZ decomposition relative to their reactions with SO2 and H2O, respectively, were estimated from the dependencies of the H2SO4 yield on the concentrations of the reactants.

Degradation of SO 2, NO 2 and NH 3 leading to formation of secondary inorganic aerosols: An environmental chamber study

NASA Astrophysics Data System (ADS)

Behera, Sailesh N.; Sharma, Mukesh

2011-08-01

We have examined the interactions of gaseous pollutants and primary aerosols that can produce secondary inorganic aerosols. The specific objective was to estimate degradation rates of precursor gases (NH 3, NO 2 and SO 2) responsible for formation of secondary inorganic aerosols. A Teflon-based outdoor environmental chamber facility (volume 12.5 m 3) was built and checked for wall losses, leaks, solar transparency and ability to simulate photochemical reactions. The chamber was equipped with state-of-the-art instrumentation to monitor concentration-time profiles of precursor gases, ozone, and aerosol. A total of 14 experimental runs were carried out for estimating the degradation of precursor gases. The following initial conditions were maintained in the chamber: NO 2 = 246 ± 104 ppb(v), NH 3 = 548 ± 83 ppb(v), SO 2 = 238 ± 107 ppb(v), O 3 = 50 ± 11 ppb(v), PM 2.5 aerosol = 283438 ± 60524 No./litre. The concentration-time profile of gases followed first-order decay and were used for estimating degradation rates (NO 2 = 0.26 ± 0.15 h -1, SO 2 = 0.31 ± 0.17 h -1, NH 3 = 0.35 ± 0.21 h -1). We observed that degradation rates showed a statistical significant positive correlation (at 5% level of significance) with the initial PM 2.5 levels in the chamber (coefficient of correlation: 0.63 for NO 2; 0.62 for NH 3 and 0.51 for SO 2), suggesting that the existing surface of the aerosol could play a significant role in degradation of precursor gases. One or more gaseous species can be adsorbed on to the existing particles and these may undergo heterogeneous or homogeneous chemical transformation to produce secondary inorganic aerosols. Through correlation analysis, we have observed that degradation rates of precursor gases were dependent on initial molar ratio of (NH 3)/(NO 2 + SO 2), indicative of ammonia-rich and ammonia-poor situations for eventual production of ammonium salts.

A pilot study of gaseous pollutants' measurement (NO2, SO2, NH3, HNO3 and O3) in Abidjan, Côte d'Ivoire: contribution to an overview of gaseous pollution in African cities

NASA Astrophysics Data System (ADS)

Bahino, Julien; Yoboué, Véronique; Galy-Lacaux, Corinne; Adon, Marcellin; Akpo, Aristide; Keita, Sékou; Liousse, Cathy; Gardrat, Eric; Chiron, Christelle; Ossohou, Money; Gnamien, Sylvain; Djossou, Julien

2018-04-01

This work is part of the DACCIWA FP7 project (Dynamics-Aerosol-Chemistry-Cloud Interactions in West Africa) in the framework of the Work Package 2 Air Pollution and Health. This study aims to characterize urban air pollution levels through the measurement of NO2, SO2, NH3, HNO3 and O3 in Abidjan, the economic capital of Côte d'Ivoire. Measurements of inorganic gaseous pollutants, i.e. NO2, SO2, NH3, HNO3 and O3 were performed in Abidjan during an intensive campaign within the dry season (15 December 2015 to 16 February 2016), using INDAAF (International Network to study Deposition and Atmospheric chemistry in AFrica) passive samplers exposed in duplicate for 2-week periods. Twenty-one sites were selected in the district of Abidjan to be representative of various anthropogenic and natural sources of air pollution in the city. Results from this intensive campaign show that gas concentrations are strongly linked to surrounding pollution sources and show a high spatial variability. Also, NH3, NO2 and O3 gases were present at relatively higher concentrations at all the sites. NH3 average concentrations varied between 9.1 ± 1.7 ppb at a suburban site and 102.1 ± 9.1 ppb at a domestic fires site. NO2 mean concentration varied from 2.7 ± 0.1 ppb at a suburban site to 25.0 ± 1.7 ppb at an industrial site. Moreover, we measured the highest O3 concentration at the two coastal sites of Gonzagueville and Félix-Houphouët-Boigny International Airport located in the southeast of the city, with average concentrations of 19.1 ± 1.7 and 18.8 ± 3.0 ppb, respectively. The SO2 average concentration never exceeded 7.2 ± 1.2 ppb over all the sites, with 71.5 % of the sampling sites showing concentrations ranging between 0.4 and 1.9 ppb. The HNO3 average concentration ranged between 0.2 and 1.4 ppb. All these results were combined with meteorological parameters to provide the first mapping of gaseous pollutants on the scale of the district of Abidjan using geostatistical

Evaluation of the solubility constants of the hydrated solid phases in the H2O-Al2O3-SO3 ternary system

NASA Astrophysics Data System (ADS)

Teyssier, A.; Lagneau, V.; Schmitt, J. M.; Counioux, J. J.; Goutaudier, C.

2017-04-01

During the acid processing of aluminosilicate ores, the precipitation of a solid phase principally consisting of hydrated aluminium hydroxysulfates may be observed. The experimental study of the H2O-Al2O3-SO3 ternary system at 25 ∘C and 101 kPa enabled to describe the solid-liquid equilibra and to identify the nature, the composition and the solubility of the solid phases which may form during the acid leaching. To predict the appearance of these aluminium hydroxysulfates in more complex systems, their solubility constants were calculated by modelling the experimental solubility results, using a geochemical reaction modelling software, CHESS. A model for non-ideality correction, based on the B-dot equation, was used as it was suitable for the considered ion concentration range. The solubility constants of three out of four solid phases were calculated: 104.08 for jurbanite (Al(SO4)(OH).5H2O), 1028.09 for the solid T (Al8(SO4)5(OH)14.34H2O) and 1027.28 for the solid V (Al10(SO4)3(OH)24.20H2O). However the activity correction model was not suitable to determine the solubility constant of alunogen (Al2(SO4)3.15.8H2O), as the ion concentrations of the mixtures were too high and beyond the allowable limits of the model. Another ionic activity correction model, based on the Pitzer equation for example, must be applied to calculate the solubility constant of alunogen.

Study on the adsorption properties of O{sub 3}, SO{sub 2}, and SO{sub 3} on B-doped graphene using DFT calculations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rad, Ali Shokuhi, E-mail: a.shokuhi@gmail.com; Shabestari, Sahand Sadeghi; Mohseni, Soheil

2016-05-15

We investigated the structure, adsorption, electronic states, and charge transfer of O{sub 3}, SO{sub 2} and SO{sub 3} molecules on the surface of a B-doped graphene using density functional theory (DFT). We found weak physisorption of SO{sub 2} (−10.9 kJ/mole, using B3LYP-D) and SO{sub 3} (−15.7 kJ/mole, using B3LYP-D) on the surface of B-doped graphene while there is strong chemisorption for O{sub 3} (−96.3 kJ/mole, using B3LYP-D ) on this surface. Our results suggest the potential of B-doped graphene as a selective sensor/adsorbent for O{sub 3} molecule. We noticed some change in hybridizing of boron from sp{sup 2} to sp{supmore » 3} upon adsorption of O{sub 3} which cases transformation of the adsorbent from 2D to 3D. - Graphical abstract: The electronic property of B-doped graphene is responsible to highly adsorption of O{sub 3} molecules while the adsorption of SO{sub 2} and SO{sub 3} molecules on this surface exhibits only a weak interaction. - Highlights: • B-doped graphene clearly is n-type semiconductor. • High negatively charge of C-atoms neighboring the boron dopant. • Chemisorption of O{sub 3} and physisorption of SO{sub 2} and SO{sub 3} on the surface of B-doped graphene.« less

Two mixed-ligand lanthanide–hydrazone complexes: [Pr(NCS)3(pbh)2]·H2O and [Nd(NCS)(NO3)(pbh)2(H2O)]NO3·2.33H2O [pbh is N′-(pyridin-2-ylmethylidene)benzo­hydrazide, C13H11N3O

PubMed Central

Paschalidis, Damianos G.; Harrison, William T. A.

2016-01-01

The gel-mediated syntheses and crystal structures of [N′-(pyridin-2-ylmethylidene-κN)benzohydrazide-κ2 N′,O]tris(thiocyanato-κN)praseodymium(III) mono­hydrate, [Pr(NCS)3(C13H11N3O)2]·H2O, (I), and aqua(nitrato-κ2 O,O′)[N′-(pyri­din-2-ylmethylidene-κN)benzohydrazide-κ2 N′,O](thiocyanato-κN)neo­dym­ium(III) nitrate 2.33-hydrate, [Nd(NCS)(NO3)(C13H11N3O)2(H2O)]NO3·2.33H2O, (II), are reported. The Pr3+ ion in (I) is coordinated by two N,N,O-tridentate N′-(pyridin-2-ylmethylidene)benzohydrazide (pbh) ligands and three N-bonded thio­cyanate ions to generate an irregular PrN7O2 coordination polyhedron. The Nd3+ ion in (II) is coordinated by two N,N,O-tridentate pbh ligands, an N-bonded thio­cyanate ion, a bidentate nitrate ion and a water mol­ecule to generate a distorted NdN5O5 bicapped square anti­prism. The crystal structures of (I) and (II) feature numerous hydrogen bonds, which lead to the formation of three-dimensional networks in each case. PMID:26958385

Ammonia Vapor-Assisted Synthesis of Cu(OH)2 and CuO Nanostructures: Anionic (Cl-, NO3 -, SO4 2-) Influence on the Product Morphology

NASA Astrophysics Data System (ADS)

Mansournia, Mohammadreza; Arbabi, Akram

2017-01-01

Shape control of inorganic nanostructures generally requires using surfactants or ligands to passivate certain crystallographic planes. This paper describes a novel additive-free synthesis of cupric oxide nanostructures with different morphologies from the aqueous solutions of copper(II) with Cl-, NO3 -, and SO4 2- as counter ions. Through a one-step approach, CuO nanoleaves, nanoparticles and flower-like microspheres were directly synthesized at 80°C upon exposure to ammonia vapor using a cupric solution as a single precursor. Furthermore, during a two-step process, Cu(OH)2 nanofibers and nanorods were prepared under an ammonia atmosphere, then converted to CuO nanostructures with morphology preservation by heat treatment in air. The as-prepared Cu(OH)2 and CuO nanostructures are characterized using x-ray diffraction, scanning electron microscopy and Fourier transformation infrared spectroscopy techniques.

A longitudinal study of sick building syndrome (SBS) among pupils in relation to SO2, NO2, O3 and PM10 in schools in China.

PubMed

Zhang, Xin; Li, Fan; Zhang, Li; Zhao, Zhuohui; Norback, Dan

2014-01-01

There are fewer longitudinal studies from China on symptoms as described for the sick building syndrome (SBS). Here, we performed a two-year prospective study and investigated associations between environmental parameters such as room temperature, relative air humidity (RH), carbon dioxide (CO2), nitrogen dioxide (NO2), sulphur dioxide (SO2), ozone (O3), particulate matter (PM10), and health outcomes including prevalence, incidence and remission of SBS symptoms in junior high schools in Taiyuan, China. Totally 2134 pupils participated at baseline, and 1325 stayed in the same classrooms during the study period (2010-2012). The prevalence of mucosal symptoms, general symptoms and symptoms improved when away from school (school-related symptoms) was 22.7%, 20.4% and 39.2%, respectively, at baseline, and the prevalence increased during follow-up (P<0.001). At baseline, both indoor and outdoor SO2 were found positively associated with prevalence of school-related symptoms. Indoor O3 was shown to be positively associated with prevalence of skin symptoms. At follow-up, indoor PM10 was found to be positively associated with new onset of skin, mucosal and general symptoms. CO2 and RH were positively associated with new onset of mucosal, general and school-related symptoms. Outdoor SO2 was positively associated with new onset of skin symptoms, while outdoor NO2 was positively associated with new onset of skin, general and mucosal symptoms. Outdoor PM10 was found to be positively associated with new onset of skin, general and mucosal symptoms as well as school-related symptoms. In conclusion, symptoms as described for SBS were commonly found in school children in Taiyuan City, China, and increased during the two-year follow-up period. Environmental pollution, including PM10, SO2 and NO2, could increase the prevalence and incidence of SBS and decrease the remission rate. Moreover, parental asthma and allergy (heredity) and pollen or pet allergy (atopy) can be risk factors for

Simultaneous removal of NO and SO2 using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS).

PubMed

Liu, Yangxian; Wang, Yan; Wang, Qian; Pan, Jianfeng; Zhang, Jun

2018-01-01

Simultaneous removal process of SO 2 and NO from flue gas using vacuum ultraviolet light (VUV)/heat/peroxymonosulfate (PMS) in a VUV spraying reactor was proposed. The key influencing factors, active species, reaction products and mechanism of SO 2 and NO simultaneous removal were investigated. The results show that vacuum ultraviolet light (185 nm) achieves the highest NO removal efficiency and yield of and under the same test conditions. NO removal is enhanced at higher PMS concentration, light intensity and oxygen concentration, and is inhibited at higher NO concentration, SO 2 concentration and solution pH. Solution temperature has a double impact on NO removal. CO 2 concentration has no obvious effect on NO removal. and produced from VUV-activation of PMS play a leading role in NO removal. O 3 and ·O produced from VUV-activation of O 2 also play an important role in NO removal. SO 2 achieves complete removal under all experimental conditions due to its very high solubility in water and good reactivity. The highest simultaneous removal efficiency of SO 2 and NO reaches 100% and 91.3%, respectively. Copyright © 2017 Elsevier Ltd. All rights reserved.

Selection of metal oxides in the preparation of rice husk ash (RHA)/CaO sorbent for simultaneous SO2 and NO removal.

PubMed

Dahlan, Irvan; Lee, Keat Teong; Kamaruddin, Azlina Harun; Mohamed, Abdul Rahman

2009-07-30

In this work, the removal of SO(2) and NO from simulated flue gas from combustion process was investigated in a fixed-bed reactor using rice husk ash (RHA)/CaO-based sorbent. Various metal precursors were used in order to select the best metal impregnated over RHA/CaO sorbents. The results showed that RHA/CaO sorbents impregnated with CeO(2) had the highest sorption capacity among other impregnated metal oxides for the simultaneous removal of SO(2) and NO. Infrared spectroscopic results indicated the formation of both sulfate (SO(4)(2-)) and nitrate (NO(3)(-)) species due to the catalytic role played by CeO(2). Apart from that, the catalytic activity of the RHA/CaO/CeO(2) sorbent was found to be closely related to its physical properties (specific surface area, total pore volume and average pore diameter).

Simultaneous purifying of Hg0, SO2, and NOx from flue gas by Fe3+/H2O2: the performance and purifying mechanism.

PubMed

Xing, Yi; Li, Liuliu; Lu, Pei; Cui, Jiansheng; Li, Qianli; Yan, Bojun; Jiang, Bo; Wang, Mengsi

2018-03-01

Hg 0 , SO 2 , and NOx result in heavily global environmental pollution and serious health hazards. Up to now, how to efficiently remove mercury with SO 2 and NOx from flue gas is still a tough task. In this study, series of high oxidizing Fenton systems were employed to purify the pollutants. The experimental results showed that Fe 3+ /H 2 O 2 was more suitable to purify Hg 0 than Fe 2+ /H 2 O 2 and Cu 2+ /H 2 O 2. The optimal condition includes Fe 3+ concentration of 0.008 mol/L, Hg 0 inlet concentration of 40 μg/m 3 , solution temperature of 50 °C, pH of 3, H 2 O 2 concentration of 0.7 mol/L, and O 2 percentage of 6%. When SO 2 and NOx were taken into account under the optimal condition, Hg 0 removal efficiency could be enhanced to 91.11% while the removal efficiency of both NOx and SO 2 was slightly declined, which was consistent to the analysis of purifying mechanism. The removal efficiency of Hg 0 was stimulated by accelerating the conversion of Fe 2+ to Fe 3+ , which resulted from the existence of SO 2 and NOx. The results of this study suggested that simultaneously purifying Hg 0 , SO 2 , and NOx from flue gas is feasible.

Synthesis, structure, and characterization of two new bismuth(III) selenite/tellurite nitrates: [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) and [Bi(TeO{sub 3})](NO{sub 3})

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meng, Chang-Yu; Wei, Ming-Fang; Geng, Lei, E-mail: lgeng.cn@gmail.com

Two new bismuth(III) selenite/tellurite nitrates, [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) and [Bi(TeO{sub 3})](NO{sub 3}), have been synthesized by conventional facile hydrothermal method at middle temperature 200 °C and characterized by single-crystal X-ray diffraction, powder diffraction, UV–vis–NIR optical absorption spectrum, infrared spectrum and thermal analylsis. Both [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) and [Bi(TeO3)](NO3) crystallize in the monoclinic centronsymmetric space group P2{sub 1}/c with a=9.9403(4) Å, b=9.6857(4) Å, c=10.6864(5) Å, β=93.1150(10)° for [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) and a=8.1489(3) Å, b=9.0663(4) Å, c=7.4729(3) Å, β=114.899(2)° for Bi(TeO3)(NO3), respectively. The two compounds, whose structures are composed of three different asymmetricmore » building units, exhibit two different types of structures. The structure of [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) features a three-dimensional (3D) bismuth(III) selenite cationic tunnel structure [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}] {sup 3}{sub ∞} with NO{sub 3}{sup −} anion group filling in the 1D tunnel along b axis. The structure of [Bi(TeO{sub 3})](NO{sub 3}) features 2D bismuth(III) tellurite [Bi(TeO{sub 3}){sub 2}]{sup 2}{sub ∞} layers separated by NO{sub 3}{sup −} anion groups. The results of optical diffuse-reflectance spectrum measurements and electronic structure calculations based on density functional theory methods show that the two compounds are wide band-gap semiconductors. - Graphical abstract: Two novel bismuth{sup III} selenite/tellurite nitrates [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) with 3D tunnel structure and [Bi(TeO{sub 3})](NO{sub 3}) with 2D layer structure have been firstly synthesized and characterized. Display Omitted - Highlights: • Two novel bismuth{sup III} nitrates [(Bi{sub 3}O{sub 2})(SeO{sub 3}){sub 2}](NO{sub 3}) and [Bi(TeO{sub 3})](NO{sub 3}) were

Permutation-symmetric three-particle hyper-spherical harmonics based on the S3 ⊗ SO(3)rot ⊂ O(2)⊗SO(3)rot ⊂ U(3)⋊S2 ⊂ O(6) subgroup chain

NASA Astrophysics Data System (ADS)

Salom, Igor; Dmitrašinović, V.

2017-07-01

We construct the three-body permutation symmetric hyperspherical harmonics to be used in the non-relativistic three-body Schrödinger equation in three spatial dimensions (3D). We label the state vectors according to the S3 ⊗ SO(3)rot ⊂ O (2) ⊗ SO(3)rot ⊂ U (3) ⋊S2 ⊂ O (6) subgroup chain, where S3 is the three-body permutation group and S2 is its two element subgroup containing transposition of first two particles, O (2) is the ;democracy transformation;, or ;kinematic rotation; group for three particles; SO(3)rot is the 3D rotation group, and U (3) , O (6) are the usual Lie groups. We discuss the good quantum numbers implied by the above chain of algebras, as well as their relation to the S3 permutation properties of the harmonics, particularly in view of the SO(3)rot ⊂ SU (3) degeneracy. We provide a definite, practically implementable algorithm for the calculation of harmonics with arbitrary finite integer values of the hyper angular momentum K, and show an explicit example of this construction in a specific case with degeneracy, as well as tables of K ≤ 6 harmonics. All harmonics are expressed as homogeneous polynomials in the Jacobi vectors (λ , ρ) with coefficients given as algebraic numbers unless the ;operator method; is chosen for the lifting of the SO(3)rot ⊂ SU (3) multiplicity and the dimension of the degenerate subspace is greater than four - in which case one must resort to numerical diagonalization; the latter condition is not met by any K ≤ 15 harmonic, or by any L ≤ 7 harmonic with arbitrary K. We also calculate a certain type of matrix elements (the Gaunt integrals of products of three harmonics) in two ways: 1) by explicit evaluation of integrals and 2) by reduction to known SU (3) Clebsch-Gordan coefficients. In this way we complete the calculation of the ingredients sufficient for the solution to the quantum-mechanical three-body bound state problem.

Characteristics of NaNO3-Promoted CdO as a Midtemperature CO2 Absorbent.

PubMed

Kim, Kang-Yeong; Kwak, Jin-Su; An, Young-In; Oh, Kyung-Ryul; Kwon, Young-Uk

2017-06-28

In this study, we explored the reaction system CdO(s) + CO 2 (g) ⇄ CdCO 3 (s) as a model system for CO 2 capture agent in the intermediate temperature range of 300-400 °C. While pure CdO does not react with CO 2 at all up to 500 °C, CdO mixed with an appropriate amount of NaNO 3 (optimal molar ratio NaNO 3 /CdO = 0.14) greatly enhances the conversion of CdO into CdCO 3 up to ∼80% (5.68 mmol/g). These NaNO 3 -promoted CdO absorbents can undergo many cycles of absorption and desorption by temperature swing between 300 and 370 °C under a 100% CO 2 condition. Details of how NaNO 3 promotes the CO 2 absorption of CdO have been delineated through various techniques using thermogravimetry, coupled with X-ray diffraction and electron microscopy. On the basis of the observed data, we propose a mechanism of CO 2 absorption and desorption of NaNO 3 -promoted CdO. The absorption proceeds through a sequence of events of CO 2 adsorption on the CdO surface covered by NaNO 3 , dissolution of so-formed CdCO 3 , and precipitation of CdCO 3 particles in the NaNO 3 medium. The desorption occurs through the decomposition of CdCO 3 in the dissolved state in the NaNO 3 medium where CdO nanoparticles are formed dispersed in the NaNO 3 medium. The CdO nanoparticles are aggregated into micrometer-large particles with smooth surfaces and regular shapes.

The reactions of SO3 with HO2 radical and H2O...HO2 radical complex. Theoretical study on the atmospheric formation of HSO5 and H2SO4.

PubMed

Gonzalez, Javier; Torrent-Sucarrat, Miquel; Anglada, Josep M

2010-03-07

The influence of a single water molecule on the gas-phase reactivity of the HO(2) radical has been investigated by studying the reactions of SO(3) with the HO(2) radical and with the H(2)O...HO(2) radical complex. The naked reaction leads to the formation of the HSO(5) radical, with a computed binding energy of 13.81 kcal mol(-1). The reaction with the H(2)O...HO(2) radical complex can give two different products, namely (a) HSO(5) + H(2)O, which has a binding energy that is computed to be 4.76 kcal mol(-1) more stable than the SO(3) + H(2)O...HO(2) reactants (Delta(E + ZPE) at 0K) and an estimated branching ratio of about 34% at 298K and (b) sulfuric acid and the hydroperoxyl radical, which is computed to be 10.51 kcal mol(-1) below the energy of the reactants (Delta(E + ZPE) at 0K), with an estimated branching ratio of about 66% at 298K. The fact that one of the products is H(2)SO(4) may have relevance in the chemistry of the atmosphere. Interestingly, the water molecule acts as a catalyst, [as it occurs in (a)] or as a reactant [as it occurs in (b)]. For a sake of completeness we have also calculated the anharmonic vibrational frequencies for HO(2), HSO(5), the HSO(5)...H(2)O hydrogen bonded complex, H(2)SO(4), and two H(2)SO(4)...H(2)O complexes, in order to help with the possible experimental identification of some of these species.

Heterogeneous oxidation of SO2 by O3-aged black carbon and its dithiothreitol oxidative potential.

PubMed

Xu, Weiwei; Li, Qian; Shang, Jing; Liu, Jia; Feng, Xiang; Zhu, Tong

2015-10-01

Ozone (O3) is an important atmospheric oxidant. Black carbon (BC) particles released into the atmosphere undergo an aging process via O3 oxidation. O3-aged BC particles may change their uptake ability toward trace reducing gases such as SO2 in the atmosphere, leading to different environmental and health effects. In this paper, the heterogeneous reaction process between O3-aged BC and SO2 was explored via in-situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Combined with ion chromatography (IC), DRIFTS was used to qualitatively and quantitatively analyze the sulfate product. The results showed that O3-aged BC had stronger SO2 oxidation ability than fresh BC, and the reactive species/sites generated on the surface had an important role in the oxidation of SO2. Relative humidity or 254nm UV (ultraviolet) light illumination enhanced the oxidation uptake of SO2 on O3-aged BC. The oxidation potentials of the BC particles were detected via dithiothreitol (DTT) assay. The DTT activity over BC was decreased in the process of SO2 reduction, with the consumption of oxidative active sites. Copyright © 2015. Published by Elsevier B.V.

Dehydration of glucose to 5-hydroxymethylfurfural by a core-shell Fe3O4@SiO2-SO3H magnetic nanoparticle catalyst

USDA-ARS?s Scientific Manuscript database

This paper discusses the potential use of (Fe3O4@SiO2-SO3H) nanoparticle catalyst for the dehydration of glucose into 5-hydroxymethylfurfural (HMF). A magnetically recoverable (Fe3O4@SiO2-SO3H) nanoparticle catalyst was successfully prepared by supporting sulfonic acid groups (SO3H) on the surface o...

Zincobotryogen, ZnFe3+(SO4)2(OH)ṡ7H2O: validation as a mineral species and new data

NASA Astrophysics Data System (ADS)

Yang, Zhuming; Giester, Gerald; Mao, Qian; Ma, Yuguang; Zhang, Di; Li, He

2017-06-01

Zincobotryogen occurs in the oxidation zone of the Xitieshan lead-zinc deposit, Qinghai, China. The mineral is associated with jarosite, copiapite, zincocopiapite, and quartz. The mineral forms prismatic crystals, 0.05 to 2 mm in size. It is optically positive (2Vcalc = 54.1°), with Z ‖ b and X ∧ c = 10°. The elongation is negative. The refractive indices are n α = 1.542(5), n β = 1.551(5), n γ = 1.587(5). The pleochroism scheme is X = colorless, Y = light yellow, Z = yellow. Microprobe analysis gave (in wt%): SO3 = 38.04, Al2O3 = 0.04, Fe2O3 = 18.46, ZnO = 13.75, MgO = 1.52, MnO = 1.23, H2O = 31.06 (by calculation), Total = 104.10. The simplified formula is (Zn,Mg)Fe3+(SO4)2(OH)ṡ7H2O. The mineral is monoclinic, P121/ n1, a = 10.504(2), b = 17.801(4), c = 7.1263(14) Å, and β = 100.08(3)°, V = 1311.9(5) Å3, Z = 4. The strongest lines in the powder X-ray diffraction pattern d(I)( hkl) are: 8.92 (100)(110), 6.32 (77)(-101), 5.56 (23)(021), 4.08 (22)(-221),3.21 (31)(231), 3.03 (34)(032), 2.77 (22)(042). The crystal structure was refined using 2816 unique reflections to R1( F) = 0.0355 and wR2( F 2) = 0.0651. The refined formula is (Zn0.84Mg0.16)Fe3+(SO4)2(OH)ṡ7H2O. The atomic arrangement is characterized by chains with composition [Fe3+(SO4)2(OH)(H2O)]2- and 7 Å repeat distance running parallel to the c-axis. The chain links to a [ MO(H2O)5] octahedron ( M = Zn, Mg) and an unshared H2O molecule, and forms a larger chain building module with composition [ M 2+Fe3+(SO4)2(OH)(H2O)6(H2O)]. The inter-chain module linkage involves only hydrogen bonding.

DFT/TD-DFT study on the electronic and spectroscopic properties of hollow cubic and hollow spherical (ZnO) m quantum dots interacting with CO, NO2 and SO3 molecules

NASA Astrophysics Data System (ADS)

Gopalakrishnan, Sankarasubramanian; Shankar, Ramasamy; Kolandaivel, Ponmalai

2018-03-01

Hollow spherical (HS) and hollow cubic (HC) (ZnO) m quantum dots (QDs) were constructed and optimized using density functional theory (DFT) method. CO, NO2 and SO3 molecules were used to interact with the HC and HS (ZnO) m QDs at the centre and on the surface of the QDs. The changes in the electronic energy levels of HC and HS (ZnO) m QDs due to the interactions of CO, NO2 and SO3 molecules have been studied. The electronic and spectroscopic properties, such as density of states, HOMO-LUMO energy gap, absorption spectra, IR and Raman spectra of HC and HS (ZnO) m QDs have been studied using DFT and Time dependent-DFT (TD-DFT) methods. The interaction energy values show that the SO3 molecule has strongly interacted with HC and HS (ZnO) m QDs than the CO and NO2 molecules. The results of the density of states show that the HC QDs have peaks that are very close to each other, whereas the same is found to be broad in the HS QDs. The HOMO-LUMO energy gap is more for the HS QDs than the HC QDs, and also it gets decreased, when the NO2 and SO3 molecules interact at the centre of the HC and HS (ZnO) m QDs. The blue and red shifts were observed in the absorption spectra of HS and HC QDs. The natural transition orbital (NTO) plot reveals that the interaction of the molecules on the surface of the QDs reduce the chance of electron-hole recombination; hence the energy gap increases for NO2 and SO3 molecular interactions on the surface of the HC and HS (ZnO) m QDs. The vibrational assignments have been made for HC and HS QDs interacting with CO, NO2 and SO3 molecules.

Hilarionite, Fe{2/3+}(SO4)(AsO4)(OH) · 6H2O, a new supergene mineral from Lavrion, Greece

NASA Astrophysics Data System (ADS)

Pekov, I. V.; Chukanov, N. V.; Yapaskurt, V. O.; Rusakov, V. S.; Belakovsky, D. I.; Turchkova, A. G.; Voudouris, P.; Magganas, A.; Katerinopoulos, A.

2014-12-01

A new mineral, hilarionite, ideally Fe{2/3+} (SO4)(AsO4)(OH) · 6H2O, has been found in the Hilarion Mine, Agios Konstantinos, Kamariza, Lavrion district, Attiki Prefecture, Greece. It was formed in the oxidation zone of a sulfide-rich orebody in association with goethite, gypsum, bukovskyite, jarosite, melanterite, chalcanthite, allophane, and azurite. Hilarionite occurs as light green (typically with an olive or grayish tint) to light yellowish green spherulites (up to 1 mm in size) and bunches of prismatic to acicular "individuals" up to 0.5 mm long that are in fact near-parallel or divergent aggregates of very thin, curved fibers up to 0.3 mm long and usually lesser than 2 μm thick. The luster is silky to vitreous. The Mohs' hardness is ca. 2. Hilarionite is ductile, its "individuals" are flexible and inelastic; fracture is uneven or splintery. D(meas) = 2.40(5), D(calc) = 2.486 g/cm3. IR spectrum shows the presence of arsenate and sulfate groups and H2O molecules in significant amounts. The Mössbauer spectrum indicates the presence of Fe3+ at two six-fold coordinated sites and the absence of Fe2+. Hilarionite is optically biaxial (+), α = 1.575(2), γ = 1.64(2), 2 V is large. The chemical composition (electron microprobe, average of 7 point analyses; H2O determined by modified Penfield method) is as follows, wt %: 0.03 MnO, 0.18 CuO, 0.17 ZnO, 33.83 Fe2O3, 0.22 P2O5, 18.92 As2O5, 22.19 SO3, 26.3 H2O, total is 101.82%. The empirical formula calculated on the basis of 15 O is: (Fe{1.90/3+}Cu0.01Zn0.01)Σ1.92[(SO4)1.24(AsO4)0.74(PO4)0.01]Σ1.99(OH)1.01 · 6.03H2O. The X-ray powder diffraction data show close structural relationship of hilarionite and kaňkite, Fe{2/3+}(AsO4)2 · 7H2O. Hilarionite is monoclinic, space group C2/ m, Cm or C2, a = 18.53(4), b = 17.43(3), c = 7.56(1) Å, β = 94.06(15)°, V = 2436(3) Å3, Z = 8. The strongest reflections in the X-ray powder diffraction pattern ( d, Å- I[ hkl]) are: 12.66-100[110], , 5.00-10[22l], , 4

Stereochemical and electronic control of M-SO/sub 2/ bonding geometry in d/sup 6/ molybdenum and tungsten SO/sub 2/ complexes: novel n/sup 1/reverse arrown/sup 2/ SO/sub 2/ linkage isomerization in Mo(CO)/sub 2/(PPh/sub 3/)/sub 2/(CNR)(SO/sub 2/) and structures of Mo(CO)/sub 3/(P-i-Pr/sub 3/)/sub 2/(SO/sub 2/) and (Mo(CO)/sub 2/(py)(PPh/sub 3/)(. mu. -SO/sub 2/))/sub 2/

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kubas, G.J.; Jarvinen, G.D.; Ryan, R.R.

1983-04-06

New complexes, mer,trans,M(CO)/sub 3/(PR/sub 3/)/sub 2/(SO/sub 2/) (M = Mo,W; R = Ph,Cy,i-Pr) (I), cis,trans-Mo(CO)/sub 2/-(PPh/sub 3/)/sub 2/(SO/sub 2/)(L) (L = NCMe,py,CNCy,CN-t-Bu and CN(p-tolyl))(II), and (Mo(CO)/sub 2/(py)(PPh/sub 3/)(..mu..-SO/sub 2/))/sub 2/, have been prepared and characterized by infrared spectroscopy, /sup 17/O and /sup 31/P NMR spectroscopy, and X-ray crystallography. Syntheses for fac-Mo(CO)/sub 3/(n/sup 2/-SO/sub 2/)(LL) (LL = dppe,bpy,phen,2 py) have also been developed. Depending upon L, II has been found to coordinate SO/sub 2/ either in the S-bonded (n/sup 1/ planar) or O,S-bonded (n/sup 2/) geometries. Remarkably, for L = CNCy or CN-t-Bu, II has been found to contain, in themore » solid state, an apparent equimixture of both coordination types. Isomerization of fac-M(CO)/sub 3/(dppe)(n/sup 2/-SO/sub 2/) (M=Mo,w; dppe = 1,2-bis(diphenylphosphino)ethane) to an n/sup 1/-planar SO/sub 2/ form, mer-M(CO)/sub 3/(dppe)(SO/sub 2/), has also been found to occur. Thus, control of the SO/sub 2/ coordination geometry has been achieved by varying either the electronic properties of the ancillary ligands or their disposition with respect to the SO/sub 2/. The X-ray crystal structure of mer,trans-Mo(CO)/sub 3/(P-i-Pr/sub 3/)/sub 2/(SO/sub 2/) revealed n/sup 1/-planar SO/sub 2/ binding, the first example of this geometry for group 6 metals. The M-S distance, 2.239 (3) angstrom, is the longest such distance for this geometry recorded to date. Crystal data: Pbca, Z=8, a=24.712(8) angstrom, b=16.033(6) angstrom, c=14.058(5) angstrom, R=0.079 for 2934 reflections with Igreater than or equal to2sigma(I). The structure of (Mo(CO)/sub 2/(py)(PPh/sub 3/)(..mu..-SO/sub 2/))/sub 2/ showed a novel SO/sub 2/ bridging geometry in which all three atoms of SO/sub 2/ are metal coordinated. Crystal data: P1, Z=1, a=14.883(4) angstrom, b=9.264(2) angstrom, c=10.808(2) angstrom, R=0.039 for 3282 reflections with Igreater than or equal to2sigma(I).« less

Synthesis of Copper-Based Nanostructured Catalysts on SiO2-Al2O3, SiO2-TiO2, and SiO2-ZrO2 Supports for NO Reduction.

PubMed

Namkhang, Pornpan; Kongkachuichay, Paisan

2015-07-01

The selective catalytic reduction of NO over a series of Cu-based catalysts supported on modified silica including SiO2-Al2O3, SiO2-TiO2, and SiO2-ZrO2 prepared via a sol-gel process and a flame spray pyrolysis (FSP) was studied. The prepared catalysts were characterized by means of TEM, XRD, XRF, TPR, and nitrogen physisorption measurement techniques, to determine particle diameter, morphology, crystallinity, phase composition, copper reducibility, surface area, and pore size of catalysts. The particles obtained from sol-gel method were almost spherical while the particles obtained from the FSP were clearly spherical and non-porous nanosized particles. The effects of Si:Al, Si:Ti, and Si:Zr molar ratio of precursor were identified as the domain for different crystalline phase of materials. It was clearly seen that a high SiO2 content inhibited the crystallization of materials. The BET surface area of catalysts obtained from sol-gel method was higher than that from the FSP and it shows that surface area increased with increasing SiO2 molar ratio due to high surface area from SiO2. The catalyst performances were tested for the selective catalytic reduction of NO with H2. It was found that the catalyst prepared over 7 wt% Cu on Si02-Al2O3 support was the most active compared with the others which converted NO as more than 70%. Moreover, the excess copper decreased the performance of NO reduction, due to the formation of CuO agglomeration covered on the porous silica as well as the alumina surface, preventing the direct contact of CO2 and AL2O3.

A comparative investigation of SO2 oxidative transfer over CuO with a CeO2 surface

NASA Astrophysics Data System (ADS)

Liu, Yifeng; Shen, Benxian; Pi, Zhipeng; Chen, Hua; Zhao, Jigang

2017-04-01

To further improve the catalytic desulfurization function of the Mg-Al spinel sulfur transfer agent in a fluid catalytic cracking (FCC) unit, the reaction paths of SO2 oxidation by O2 over the metal oxide surface of CuO (111) and CeO2 (111) were investigated. In reference to the fact that SO2 reacting with O2 over CuO was a Mars-van Krevelen cycle, a similar reaction law for SO2 oxidation over CeO2 was also verified by characterization methods (e.g., IR, XPS). Meanwhile, the molecular simulation results indicated that the rate-control step of SO2 oxidation over CeO2 (111) and CuO (111) was a SO3 desorption step. The lower energy barrier in the rate-control step corresponded to better catalytic performance; hence, it could explain the reason that CeO2 had a better sulfur oxidization transfer performance than CuO.

Porous sulfated metal oxide SO4 2-/Fe2O3 as an anode material for Li-ion batteries with enhanced electrochemical performance

NASA Astrophysics Data System (ADS)

Li, Zhen; Lv, Qianqian; Huang, Xiaoxiong; Tan, Yueyue; Tang, Bohejin

2017-01-01

Sulfated metal oxide SO4 2-/Fe2O3 was prepared by a novel facile sol-gel method combined with a subsequent heating treatment process. The as-synthesized products were analyzed by XRD, FTIR, and FE-SEM. Compared with the unsulfated Fe2O3, the agglomeration of particles has been alleviated after the incorporation of SO4 2-. Interestingly, the primary particle size of the SO4 2-/Fe2O3 (about 5 nm) is similar to its normal counterparts even after the calcination treatment. More importantly, SO4 2-/Fe2O3 exhibits a porous architecture, which is an intriguing feature for electrode materials. When used as anode materials in Li-ion batteries, SO4 2-/Fe2O3 delivered a higher reversible discharge capacity (992 mAh g-1), with smaller charge transfer resistance, excellent rate performance, and better cycling stability than normal Fe2O3. We believed that the presence of SO4 2- and porous architecture should be responsible for the enhanced electrochemical performance, which could provide more continuous and accessible conductive paths for Li+ and electrons.

Dry deposition of O3 and SO2 estimated from gradient measurements above a temperate mixed forest.

PubMed

Wu, Zhiyong; Staebler, Ralf; Vet, Robert; Zhang, Leiming

2016-03-01

Vertical profiles of O3 and SO2 concentrations were monitored at the Borden Forest site in southern Ontario, Canada from May 2008 to April 2013. A modified gradient method (MGM) was applied to estimate O3 and SO2 dry deposition fluxes using concentration gradients between a level above and a level below the canopy top. The calculated five-year mean (median) dry deposition velocity (Vd) were 0.35 (0.27) and 0.59 (0.54) cm s(-1), respectively, for O3 and SO2. Vd(O3) exhibited large seasonal variations with the highest monthly mean of 0.68 cm s(-1) in August and the lowest of 0.09 cm s(-1) in February. In contrast, seasonal variations of Vd(SO2) were smaller with monthly means ranging from 0.48 (May) to 0.81 cm s(-1) (December). The different seasonal variations between O3 and SO2 were caused by the enhanced SO2 uptake by snow surfaces in winter. Diurnal variations showed a peak value of Vd in early morning in summer months for both O3 and SO2. Canopy wetness increased the non-stomatal uptake of O3 while decreasing the stomatal uptake. This also applied to SO2, but additional factors such as surface acidity also played an important role on the overall uptake. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Characterization of trace gases measured over Alberta oil sands mining operations: 76 speciated C2-C10 volatile organic compounds (VOCs), CO2, CH4, CO, NO, NO2, NOy, O3 and SO2

NASA Astrophysics Data System (ADS)

Simpson, I. J.; Blake, N. J.; Barletta, B.; Diskin, G. S.; Fuelberg, H. E.; Gorham, K.; Huey, L. G.; Meinardi, S.; Rowland, F. S.; Vay, S. A.; Weinheimer, A. J.; Yang, M.; Blake, D. R.

2010-08-01

Oil sands comprise 30% of the world's oil reserves and the crude oil reserves in Canada's oil sands deposits are second only to Saudi Arabia. The extraction and processing of oil sands is much more challenging than for light sweet crude oils because of the high viscosity of the bitumen contained within the oil sands and because the bitumen is mixed with sand and contains chemical impurities such as sulphur. Despite these challenges, the importance of oil sands is increasing in the energy market. To our best knowledge this is the first peer-reviewed study to characterize volatile organic compounds (VOCs) emitted from Alberta's oil sands mining sites. We present high-precision gas chromatography measurements of 76 speciated C2-C10 VOCs (alkanes, alkenes, alkynes, cycloalkanes, aromatics, monoterpenes, oxygenates, halocarbons, and sulphur compounds) in 17 boundary layer air samples collected over surface mining operations in northeast Alberta on 10 July 2008, using the NASA DC-8 airborne laboratory as a research platform. In addition to the VOCs, we present simultaneous measurements of CO2, CH4, CO, NO, NO2, NOy, O3 and SO2, which were measured in situ aboard the DC-8. Methane, CO, CO2, NO, NO2, NOy, SO2 and 53 VOCs (e.g., halocarbons, sulphur species, NMHCs) showed clear statistical enhancements (up to 1.1-397×) over the oil sands compared to local background values and, with the exception of CO, were higher over the oil sands than at any other time during the flight. Twenty halocarbons (e.g., CFCs, HFCs, halons, brominated species) either were not enhanced or were minimally enhanced (< 10%) over the oil sands. Ozone levels remained low because of titration by NO, and three VOCs (propyne, furan, MTBE) remained below their 3 pptv detection limit throughout the flight. Based on their mutual correlations, the compounds emitted by the oil sands industry fell into two groups: (1) evaporative emissions from the oil sands and its products and/or from the diluent used to

SO2 and NH3 gas adsorption on a ternary ZnO/CuO/CuCl2 impregnated activated carbon evaluated using combinatorial methods.

PubMed

Romero, Jennifer V; Smith, Jock W H; Sullivan, Braden M; Croll, Lisa M; Dahn, J R

2012-01-09

Ternary libraries of 64 ZnO/CuO/CuCl(2) impregnated activated carbon samples were prepared on untreated or HNO(3)-treated carbon and evaluated for their SO(2) and NH(3) gas adsorption properties gravimetrically using a combinatorial method. CuCl(2) is shown to be a viable substitute for HNO(3) and some compositions of ternary ZnO/CuO/CuCl(2) impregnated carbon samples prepared on untreated carbon provided comparable SO(2) and NH(3) gas removal capacities to the materials prepared on HNO(3)-treated carbon. Through combinatorial methods, it was determined that the use of HNO(3) in this multigas adsorbent formulation can be avoided.

Characterization of trace gases measured over Alberta oil sands mining operations: 76 speciated C2-C10 volatile organic compounds (VOCs), CO2, CH4, CO, NO, NO2, NOy, O3 and SO2

NASA Astrophysics Data System (ADS)

Simpson, I. J.; Blake, N. J.; Barletta, B.; Diskin, G. S.; Fuelberg, H. E.; Gorham, K.; Huey, L. G.; Meinardi, S.; Rowland, F. S.; Vay, S. A.; Weinheimer, A. J.; Yang, M.; Blake, D. R.

2010-12-01

Oil sands comprise 30% of the world's oil reserves and the crude oil reserves in Canada's oil sands deposits are second only to Saudi Arabia. The extraction and processing of oil sands is much more challenging than for light sweet crude oils because of the high viscosity of the bitumen contained within the oil sands and because the bitumen is mixed with sand and contains chemical impurities such as sulphur. Despite these challenges, the importance of oil sands is increasing in the energy market. To our best knowledge this is the first peer-reviewed study to characterize volatile organic compounds (VOCs) emitted from Alberta's oil sands mining sites. We present high-precision gas chromatography measurements of 76 speciated C2-C10 VOCs (alkanes, alkenes, alkynes, cycloalkanes, aromatics, monoterpenes, oxygenated hydrocarbons, halocarbons and sulphur compounds) in 17 boundary layer air samples collected over surface mining operations in northeast Alberta on 10 July 2008, using the NASA DC-8 airborne laboratory as a research platform. In addition to the VOCs, we present simultaneous measurements of CO2, CH4, CO, NO, NO2, NOy, O3 and SO2, which were measured in situ aboard the DC-8. Carbon dioxide, CH4, CO, NO, NO2, NOy, SO2 and 53 VOCs (e.g., non-methane hydrocarbons, halocarbons, sulphur species) showed clear statistical enhancements (1.1-397×) over the oil sands compared to local background values and, with the exception of CO, were greater over the oil sands than at any other time during the flight. Twenty halocarbons (e.g., CFCs, HFCs, halons, brominated species) either were not enhanced or were minimally enhanced (<10%) over the oil sands. Ozone levels remained low because of titration by NO, and three VOCs (propyne, furan, MTBE) remained below their 3 pptv detection limit throughout the flight. Based on their correlations with one another, the compounds emitted by the oil sands industry fell into two groups: (1) evaporative emissions from the oil sands and its

Challenges in the Search for Magnetic Coupling in 3d/4f Materials: Syntheses, Structures, and Magnetic Properties of the Lanthanide Copper Heterobimetallic Compounds, RE 2 Cu(TeO 3 ) 2 (SO 4 ) 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lin, Jian; Chai, Ping; Diefenbach, Kariem

2014-03-03

Twelve new lanthanide copper heterobimetallic compounds, RE2Cu(TeO3)2(SO4)2 (RE = Y, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu), with two different structural topologies, have been prepared by hydrothermal treatment. Both structure types crystallize in the triclinic space group, Pmore » $$\\bar{1}$$, but the unit cell parameters and structures are quite different. The earlier RE2Cu(TeO3)2(SO4)2 (RE = Y, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, and Tm) share a common structural motif consisting of edge-sharing LnO8 chains and [Cu(TeO3)2(SO4)2]6– units. The later lanthanide version (Yb and Lu) is composed of edge-sharing LnO7 dimers bridged by similar [Cu(TeO3)2(SO4)2]6– units. The change in the structure type can be attributed to the decreasing ionic radii of the lanthanides. The compounds containing RE3+ ions with diamagnetic ground states (Y3+ and Eu3+) exhibit antiferromagnetic ordering at 12.5 K and 15 K, respectively, owing to the magnetic exchange between Cu2+ moments. No magnetic phase transition was observed in all the other phases. The lack of magnetic ordering is attributed to the competing magnetic interactions caused by the presence of paramagnetic RE3+ ions. The magnetism data suggests that substantial 3d–4f coupling only occurs in the Yb analogue.« less

[{(Mo)Mo5O21(H2O)3(SO4)}12(VO)30(H2O)20]36-: a molecular quantum spin icosidodecahedron.

PubMed

Botar, Bogdan; Kögerler, Paul; Hill, Craig L

2005-07-07

Self-assembly of aqueous solutions of molybdate and vanadate under reducing, mildly acidic conditions results in a polyoxomolybdate-based {Mo72V30} cluster compound Na8K16(VO)(H2O)5[K10 subset{(Mo)Mo5O21(H2O)3(SO4)}12(VO)30(H2O)20].150H2O, 1, a quantum spin-based Keplerate structure.

New family of lanthanide-based inorganic-organic hybrid frameworks: Ln2(OH)4[O3S(CH2)nSO3]·2H2O (Ln = La, Ce, Pr, Nd, Sm; n = 3, 4) and their derivatives.

PubMed

Liang, Jianbo; Ma, Renzhi; Ebina, Yasuo; Geng, Fengxia; Sasaki, Takayoshi

2013-02-18

We report the synthesis and structure characterization of a new family of lanthanide-based inorganic-organic hybrid frameworks, Ln(2)(OH)(4)[O(3)S(CH(2))(n)SO(3)]·2H(2)O (Ln = La, Ce, Pr, Nd, Sm; n = 3, 4), and their oxide derivatives. Highly crystallized samples were synthesized by homogeneous precipitation of Ln(3+) ions from a solution containing α,ω-organodisulfonate salts promoted by slow hydrolysis of hexamethylenetetramine. The crystal structure solved from powder X-ray diffraction data revealed that this material comprises two-dimensional cationic lanthanide hydroxide {[Ln(OH)(2)(H(2)O)](+)}(∞) layers, which are cross-linked by α,ω-organodisulfonate ligands into a three-dimensional pillared framework. This hybrid framework can be regarded as a derivative of UCl(3)-type Ln(OH)(3) involving penetration of organic chains into two {LnO(9)} polyhedra. Substitutional modification of the lanthanide coordination promotes a 2D arrangement of the {LnO(9)} polyhedra. A new hybrid oxide, Ln(2)O(2)[O(3)S(CH(2))(n)SO(3)], which is supposed to consist of alternating {[Ln(2)O(2)](2+)}(∞) layers and α,ω-organodisulfonate ligands, can be derived from the hydroxide form upon dehydration/dehydroxylation. These hybrid frameworks provide new opportunities to engineer the interlayer chemistry of layered structures and achieve advanced functionalities coupled with the advantages of lanthanide elements.

Next-Generation Aura/OMI NO2 and SO2 Products

NASA Technical Reports Server (NTRS)

Krotkov, Nickolay; Yang, Kai; Bucsela, Eric; Lamsal, Lok; Celarier, Edward; Swartz, William; Carn, Simon; Bhartia, Pawan; Gleason, James; Pickering, Ken;

Crystal structures of NiSO4·9H2O and NiSO4·8H2O: magnetic properties, stability with respect to morenosite (NiSO4·7H2O), the solid-solution series (Mg x Ni1-x )SO4·9H2O

NASA Astrophysics Data System (ADS)

Fortes, A. D.; Knight, K. S.; Gibbs, A. S.; Wood, I. G.

2018-02-01

Since being discovered initially in mixed-cation systems, a method of forming end-member NiSO4·9H2O and NiSO4·8H2O has been found. We have obtained powder diffraction data from protonated analogues (with X-rays) and deuterated analogues (using neutrons) of these compounds over a range of temperatures, allowing us to determine their crystal structures—including all H-atoms—and to characterise the transitions on warming from 220 to 278 K; glass → 9-hydrate → 8-hydrate + ice → 7-hydrate + ice → partial melt (7-hydrate + liquid). NiSO4·8D2O is triclinic, space-group P\\bar {1} , Z = 2, with unit cell parameters at 150 K, a = 6.12463(8) Å, b = 6.8401(1) Å, c = 12.5339(2) Å, α = 92.846(1)°, β = 97.822(1)°, γ = 96.627(1)° and V = 515.58(1) Å3. The structure consists of two symmetry-inequivalent Ni(D2O)6 octahedra on sites of \\bar {1} symmetry. These are directly joined by a water-water H-bond to form chains of octahedra parallel with the c-axis at x = 0. Two interstitial water molecules serve both to bridge the Ni(D2O)6 octahedral chains in the b-c plane and also to connect with the SO4 2- tetrahedral oxyanion. These tetrahedra are linked by the two interstitial water molecules in a reticular motif to form sheets perpendicular to c. NiSO4·9D2O is monoclinic, space-group P21/c, Z = 4, with unit-cell parameters at 150 K, a = 6.69739(6) Å, b = 11.8628(1) Å, c = 14.5667(1) Å, β = 94.9739(8)° and V = 1152.96(1) Å3. The structure is isotypic with the Mg analogue described elsewhere (Fortes et al., Acta Cryst B 73:47‒64, 2017b). It shares the motif of H-bonded octahedral chains with NiSO4·8D2O, although in the enneahydrate these run parallel with the b-axis at x = 0. Three interstitial water molecules bridge the Ni(D2O)6 octahedra to the SO4 2- tetrahedral oxyanion. The tetrahedra sit at x ≈ 0.5 and are linked by two of the three interstitial water molecules in a pentagonal motif to form ribbons parallel with b. A solid-solution series

The system K2Mg2(SO4)3 (langbeinite)-K2Ca2(SO4)3 (calcium-langbeinite)

USGS Publications Warehouse

Morey, G.W.; Rowe, J.J.; Fournier, R.O.

1964-01-01

The join between the compositions K2Mg2(SO4)3 and K2Ca2(SO4)3 was studied by means of high-temperature equilibrium quenching techniques and by means of a heating stage mounted on an X-ray diffractometer. Complete solid solution exists in the system, but at 25??C members of the solid solution series are isometric only in the composition range 0-73??5 wt. per cent K2Ca2(SO4)3. At compositions richer in K2Ca2(SO4)3 than 73??5 wt. per cent, members of the series are optically biaxial. At higher temperatures members of the solid solution series are isometric at successively more calcium-rich compositions and pure K2Ca2(SO4)3 is isometric above about 200 ?? 2??C. The system is not binary, as mixtures richer in K2Ca2(SO4)3 than 42 wt. per cent decompose with the formation of liquid and CaSO4. ?? 1964.

Large hydrogen-bonded pre-nucleation (HSO4-)(H2SO4)m(H2O)k and (HSO4-)(NH3)(H2SO4)m(H2O)k clusters in the earth's atmosphere.

PubMed

Herb, Jason; Xu, Yisheng; Yu, Fangqun; Nadykto, A B

2013-01-10

The importance of pre-nucleation cluster stability as the key parameter controlling nucleation of atmospheric airborne ions is well-established. In this Article, large ternary ionic (HSO(4)(-))(H(2)SO(4))(m)(NH(3))(H(2)O)(n) clusters have been studied using Density Functional Theory (DFT) and composite ab initio methods. Twenty classes of clusters have been investigated, and thermochemical properties of common atmospheric (HSO(4)(-))(H(2)SO(4))(m)(NH(3))(0)(H(2)O)(k) and (HSO(4)(-))(H(2)SO(4))(m)(NH(3))(1)(H(2)O)(n) clusters (with m, k, and n up to 3) have been obtained. A large amount of new themochemical and structural data ready-to-use for constraining kinetic nucleation models has been reported. We have performed a comprehensive thermochemical analysis of the obtained data and have investigated the impacts of ammonia and negatively charged bisulfate ion on stability of binary clusters in some detail. The comparison of theoretical predictions and experiments shows that the PW91PW91/6-311++G(3df,3pd) results are in very good agreement with both experimental data and high level ab initio CCSD(T)/CBS values and suggest that the PW91PW91/6-311++G(3df,3pd) method is a viable alternative to higher level ab initio methods in studying large pre-nucleation clusters, for which the higher level computations are prohibitively expensive. The uncertainties in both theory and experiments have been investigated, and possible ways of their reduction have been proposed.

High temperature redox reactions with uranium: Synthesis and characterization of Cs(UO{sub 2})Cl(SeO{sub 3}), Rb{sub 2}(UO{sub 2}){sub 3}O{sub 2}(SeO{sub 3}){sub 2}, and RbNa{sub 5}U{sub 2}(SO{sub 4}){sub 7}

DOE Office of Scientific and Technical Information (OSTI.GOV)

Babo, Jean-Marie; Department of Civil and Environmental Engineering and Earth Sciences and Department of Chemistry and Biochemistry, University of Notre Dame, Notre Dame, IN 46556; Albrecht-Schmitt, Thomas E., E-mail: talbrechtschmitt@gmail.com

2013-10-15

Cs(UO{sub 2})Cl(SeO{sub 3}) (1), Rb{sub 2}(UO{sub 2}){sub 3}O{sub 2}(SeO{sub 3}){sub 3} (2), and RbNa{sub 5}U{sub 2}(SO{sub 4}){sub 7} (3) single crystals were synthesized using CsCl, RbCl, and a CuCl/NaCl eutectic mixture as fluxes, respectively. Their lattice parameters and space groups are as follows: P2{sub 1}/n (a=6.548(1) Å, b=11.052(2) Å, c=10.666(2) Å and β=93.897(3)°), P1{sup ¯} (a=7.051(2) Å, b=7.198(2) Å, c=8.314(2) Å, α=107.897(3)°, β=102.687(3)° and γ=100.564(3)°) and C2/c (a=17.862(4) Å, b=6.931(1) Å, c=20.133(4) Å and β=109.737(6)°. The small anionic building units found in these compounds are SeO{sub 3}{sup 2−} and SO{sub 4}{sup 2−} tetrahedra, oxide, and chloride. The crystal structure ofmore » the first compound is composed of [(UO{sub 2}){sub 2}Cl{sub 2}(SeO{sub 3}){sub 2}]{sup 2−} chains separated by Cs{sup +} cations. The structure of (2) is constructed from [(UO{sub 2}){sub 3}O{sub 11}]{sup 16−} chains further connected through selenite units into layers stacked perpendicularly to the [0 1 0] direction, with Rb{sup +} cations intercalating between them. The structure of compound (3) is made of uranyl sulfate layers formed by edge and vertex connections between dimeric [U{sub 2}O{sub 16}] and [SO{sub 4}] polyhedra. These layers contain unusual sulfate–metal connectivity as well as large voids. - Graphical abstract: A new family of uranyl selenites and sulfates has been prepared by high-temperature redox reactions. This compounds display new bonding motifs. Display Omitted - Highlights: • Low-dimensional Uranyl Oxoanion compounds. • Conversion of U(IV) to U(VI) at high temperatures. • Dimensional reduction by both halides and stereochemically active lone-pairs.« less

Theoretical study on atmospheric reactions of fluoranthene and pyrene with N2O5/NO3/NO2

NASA Astrophysics Data System (ADS)

Wang, Youfeng; Yang, Bo; Shu, Jinian; Li, Nana; Zhang, Peng; Sun, Wanqi

2015-08-01

It is complex to assign the products obtained from the gas-phase reactions of PAHs with NO3/NO2 and N2O5. For this purpose, theoretical calculations are performed. Results show that 2-nitrofluoranthene and 2-nitropyrene are the dominant products for reactions of fluoranthene and pyrene with NO3/NO2, while 3-nitrofluoranthene and 1-nitropyrene are the major nitration products of N2O5. SN2 reaction mechanisms are elucidated and homolytic mechanisms are calculated for the first time. Rate constants for reactions of fluoranthene and pyrene with N2O5 are deduced for the first time, which are 2.50 × 10-27 and 2.16 × 10-24 cm3 molecule-1 s-1, respectively at 298 K.

Simultaneous adsorption of SO2 and NO from flue gas over mesoporous alumina.

PubMed

Sun, Xin; Tang, Xiaolong; Yi, Honghong; Li, Kai; Ning, Ping; Huang, Bin; Wang, Fang; Yuan, Qin

2015-01-01

Mesoporous alumina (MA) with a higher ability to simultaneously remove SO2 and NO was prepared by the evaporation-induced self-assembly process. The adsorption capacities of MA are 1.79 and 0.702 mmol/g for SO2 and NO, respectively. The Brunauer-Emmett-Teller method was used to characterize the adsorbent. Simultaneous adsorption of SO2 and NO from flue gas over MA in different operating conditions had been studied in a fixed bed reactor. The effects of temperature, oxygen concentration and water vapour were investigated. The experimental results showed that the optimum temperature for MA to simultaneously remove SO2 and NO was 90°C. The simultaneous adsorption capacities of SO2 and NO could be enhanced by increasing O2 when its concentration was below 5%. The changes of simultaneous adsorption capacities were not obvious when O2 concentration was above 5%. The increase in relative humidity results in an increase after dropping of SO2 adsorption capacity, whereas the adsorption capacity of NO showed an opposite trend. The results suggest that MA is a great adsorbent for simultaneous removal of SO2 and NO from flue gas.

Process for simultaneous removal of SO.sub.2 and NO.sub.x from gas streams

DOEpatents

Rosenberg, Harvey S.

1987-01-01

A process for simultaneous removal of SO.sub.2 and NO.sub.x from a gas stream that includes flowing the gas stream to a spray dryer and absorbing a portion of the SO.sub.2 content of the gas stream and a portion of the NO.sub.x content of the gas stream with ZnO by contacting the gas stream with a spray of an aqueous ZnO slurry; controlling the gas outlet temperature of the spray dryer to within the range of about a 0.degree. to 125.degree. F. approach to the adiabatic saturation temperature; flowing the gas, unreacted ZnO and absorbed SO.sub.2 and NO.sub.x from the spray dryer to a fabric filter and collecting any solids therein and absorbing a portion of the SO.sub.2 remaining in the gas stream and a portion of the NO.sub.x remaining in the gas stream with ZnO; and controlling the ZnO content of the aqueous slurry so that sufficient unreacted ZnO is present in the solids collected in the fabric filter to react with SO.sub.2 and NO.sub.x as the gas passes through the fabric filter whereby the overall feed ratio of ZnO to SO.sub.2 plus NO.sub.x is about 1.0 to 4.0 moles of ZnO per of SO.sub.2 and about 0.5 to 2.0 moles of ZnO per mole of NO.sub.x. Particulates may be removed from the gas stream prior to treatment in the spray dryer. The process further allows regeneration of ZnO that has reacted to absorb SO.sub.2 and NO.sub.x from the gas stream and acid recovery.

Process for simultaneous removal of SO[sub 2] and NO[sub x] from gas streams

DOEpatents

Rosenberg, H.S.

1987-02-03

A process is described for simultaneous removal of SO[sub 2] and NO[sub x] from a gas stream that includes flowing the gas stream to a spray dryer and absorbing a portion of the SO[sub 2] content of the gas stream and a portion of the NO[sub x] content of the gas stream with ZnO by contacting the gas stream with a spray of an aqueous ZnO slurry; controlling the gas outlet temperature of the spray dryer to within the range of about a 0 to 125 F approach to the adiabatic saturation temperature; flowing the gas, unreacted ZnO and absorbed SO[sub 2] and NO[sub x] from the spray dryer to a fabric filter and collecting any solids therein and absorbing a portion of the SO[sub 2] remaining in the gas stream and a portion of the NO[sub x] remaining in the gas stream with ZnO; and controlling the ZnO content of the aqueous slurry so that sufficient unreacted ZnO is present in the solids collected in the fabric filter to react with SO[sub 2] and NO[sub x] as the gas passes through the fabric filter whereby the overall feed ratio of ZnO to SO[sub 2] plus NO[sub x] is about 1.0 to 4.0 moles of ZnO per of SO[sub 2] and about 0.5 to 2.0 moles of ZnO per mole of NO[sub x]. Particulates may be removed from the gas stream prior to treatment in the spray dryer. The process further allows regeneration of ZnO that has reacted to absorb SO[sub 2] and NO[sub x] from the gas stream and acid recovery. 4 figs.

Adsorption and desorption of SO2, NO and chlorobenzene on activated carbon.

PubMed

Li, Yuran; Guo, Yangyang; Zhu, Tingyu; Ding, Song

2016-05-01

Activated carbon (AC) is very effective for multi-pollutant removal; however, the complicated components in flue gas can influence each other's adsorption. A series of adsorption experiments for multicomponents, including SO2, NO, chlorobenzene and H2O, on AC were performed in a fixed-bed reactor. For single-component adsorption, the adsorption amount for chlorobenzene was larger than for SO2 and NO on the AC. In the multi-component atmosphere, the adsorption amount decreased by 27.6% for chlorobenzene and decreased by 95.6% for NO, whereas it increased by a factor of two for SO2, demonstrating that a complex atmosphere is unfavorable for chlorobenzene adsorption and inhibits NO adsorption. In contrast, it is very beneficial for SO2 adsorption. The temperature-programmed desorption (TPD) results indicated that the binding strength between the gas adsorbates and the AC follows the order of SO2>chlorobenzene > NO. The adsorption amount is independent of the binding strength. The presence of H2O enhanced the component effects, while it weakened the binding force between the gas adsorbates and the AC. AC oxygen functional groups were analyzed using TPD and X-ray photoelectron spectroscopy (XPS) measurements. The results reveal the reason why the chlorobenzene adsorption is less affected by the presence of other components. Lactone groups partly transform into carbonyl and quinone groups after chlorobenzene desorption. The chlorobenzene adsorption increases the number of C=O groups, which explains the positive effect of chlorobenzene on SO2 adsorption and the strong NO adsorption. Copyright © 2015. Published by Elsevier B.V.

Reflected shock tube studies of high-temperature rate constants for OH + NO2 --> HO2 + NO and OH + HO2 --> H2O + O2.

PubMed

Srinivasan, Nanda K; Su, Meng-Chih; Sutherland, James W; Michael, Joe V; Ruscic, Branko

2006-06-01

The motivation for the present study comes from the preceding paper where it is suggested that accepted rate constants for OH + NO2 --> NO + HO2 are high by approximately 2. This conclusion was based on a reevaluation of heats of formation for HO2, OH, NO, and NO2 using the Active Thermochemical Table (ATcT) approach. The present experiments were performed in C2H5I/NO2 mixtures, using the reflected shock tube technique and OH-radical electronic absorption detection (at 308 nm) and using a multipass optical system. Time-dependent profile decays were fitted with a 23-step mechanism, but only OH + NO2, OH + HO2, both HO2 and NO2 dissociations, and the atom molecule reactions, O + NO2 and O + C2H4, contributed to the decay profile. Since all of the reactions except the first two are known with good accuracy, the profiles were fitted by varying only OH + NO2 and OH + HO2. The new ATcT approach was used to evaluate equilibrium constants so that back reactions were accurately taken into account. The combined rate constant from the present work and earlier work by Glaenzer and Troe (GT) is k(OH+NO2) = 2.25 x 10(-11) exp(-3831 K/T) cm3 molecule(-1) s(-1), which is a factor of 2 lower than the extrapolated direct value from Howard but agrees well with NO + HO2 --> OH + NO2 transformed with the updated equilibrium constants. Also, the rate constant for OH + HO2 suitable for combustion modeling applications over the T range (1200-1700 K) is (5 +/- 3) x 10(-11) cm3 molecule(-1) s(-1). Finally, simulating previous experimental results of GT using our updated mechanism, we suggest a constant rate for k(HO2+NO2) = (2.2 +/- 0.7) x 10(-11) cm3 molecule(-1) s(-1) over the T range 1350-1760 K.

Low-temperature co-purification of NO x and Hg0 from simulated flue gas by Ce x Zr y Mn z O2/r-Al2O3: the performance and its mechanism.

PubMed

Lu, Pei; Yue, Huifang; Xing, Yi; Wei, Jianjun; Zeng, Zheng; Li, Rui; Wu, Wanrong

2018-05-11

In this study, series of Ce x Zr y Mn z O 2 /r-Al 2 O 3 catalysts were prepared by impregnation method and explored to co-purification of NO x and Hg 0 at low temperature. The physical and chemical properties of the catalysts were investigated by XRD, BET, FTIR, NH 3 -TPD, H 2 -TPR, and XPS. The experimental results showed that 10% Ce 0.2 Zr 0.3 Mn 0.5 O 2 /r-Al 2 O 3 yielded higher conversion on co-purification of NO x and Hg 0 than the other prepared catalysts at low temperature, especially at 200-300 °C. 91% and 97% convert rate of NO x and Hg 0 were obtained, respectively, when 10% Ce 0.2 Zr 0.3 Mn 0.5 O 2 /r-Al 2 O 3 catalyst was used at 250 °C. Moreover, the presence of H 2 O slightly decreased the removal of NO x and Hg 0 owing to the competitive adsorption of H 2 O and Hg 0 . When SO 2 was added, the removal of Hg 0 first increased slightly and then presented a decrease due to the generation of SO 3 and (NH 4 ) 2 SO 4 . The results of NH 3 -TPD indicated that the strong acid of 10% Ce 0.2 Zr 0.3 Mn 0.5 O 2 /r-Al 2 O 3 improved its high-temperature activity. XPS and H 2 -TPR results showed there were high-valence Mn and Ce species in 10% Ce 0.2 Zr 0.3 Mn 0.5 O 2 /r-Al 2 O 3 , which could effectively promote the removal of NO x and Hg 0 . Therefore, the mechanisms of Hg 0 and NO x removal were proposed as Hg (ad) + [O] → HgO (ad), and 2NH 3 /NH 4 + (ad) + NO 2 (ad) + NO (g) → 2 N 2  + 3H 2 O/2H + , respectively. Graphical abstract ᅟ.

Empirical electronic polarizabilities: deviations from the additivity rule. I. M2+SO4·nH2O, blödite Na2M2+(SO4)2·4H2O, and kieserite-related minerals with sterically strained structures

NASA Astrophysics Data System (ADS)

Gagné, Olivier; Hawthorne, Frank; Shannon, Robert D.; Fischer, Reinhard X.

2017-09-01

Empirical electronic polarizabilities allow the prediction of total mineral polarizabilities and mean refractive indices of the vast majority of minerals and synthetic oxides. However, deviations from the valence-sum rule at cations in some minerals are associated with large deviations of observed from calculated total polarizabilities. We have identified several groups of minerals and compounds where deviations from the valence-sum rule at cations lead to polarizability deviations of 2-5%: M(SO4)·nH2O, n = 1-6, blödite-group minerals [Na2M2+(SO4)2·4H2O], and the kieserite-related minerals: isokite, panasqueiraite and tilasite. In these minerals, the environment of the M ions contains both O and H2O: Mg[O4(H2O)2] in kieserite, szmikite, and szomolnokite; Mg[O2(H2O)4] in starkeyite, ilesite, and rozenite, and Mg[(H2O)6] in hexahydrite. In compounds where the ligands are only H2O, deviations from the valence-sum rule at the M(H2O)6 groups are not accompanied by significant polarizability deviations. This is the case for epsomite, MgSO4·7H2O; bieberite, CoSO4·7H2O; goslarite, ZnSO4·7H2O, six silicofluorides, MSiF6·6H2O; eighteen Tutton's salts, M2M'(SO4)2·6H2O, where M = K, Rb, Cs and M' = Mg, Mn, Fe, Co, Ni, Cu, and Zn; and eleven MM'(SO4)2·12H2O alums, where M = Na, K, Rb and Cs, and M' = Al, Cr, Ga and In. This is also the case for the sulfates alunogen, Al2(SO4)3·17H2O and halotrichite, FeAl2(SO4)4·22H2O; three hydrated nitrates; one phosphate; three antimonates and two hydrated perchlorates. A possible explanation for this different behavior is that the bond-valence model treats O and H separately, whereas polarizability calculations treat the polarizability of the entire H2O molecule.

Vibrational spectroscopy of NO + (H2O)n: Evidence for the intracluster reaction NO + (H2O)n --> H3O + (H2O)n - 2 (HONO) at n => 4

NASA Astrophysics Data System (ADS)

Choi, Jong-Ho; Kuwata, Keith T.; Haas, Bernd-Michael; Cao, Yibin; Johnson, Matthew S.; Okumura, Mitchio

1994-05-01

Infrared spectra of mass-selected clusters NO+(H2O)n for n=1 to 5 were recorded from 2700 to 3800 cm-1 by vibrational predissociation spectroscopy. Vibrational frequencies and intensities were also calculated for n=1 and 2 at the second-order Møller-Plesset (MP2) level, to aid in the interpretation of the spectra, and at the singles and doubles coupled cluster (CCSD) level energies of n=1 isomers were computed at the MP2 geometries. The smaller clusters (n=1 to 3) were complexes of H2O ligands bound to a nitrosonium ion NO+ core. They possessed perturbed H2O stretch bands and dissociated by loss of H2O. The H2O antisymmetric stretch was absent in n=1 and gradually increased in intensity with n. In the n=4 clusters, we found evidence for the beginning of a second solvation shell as well as the onset of an intracluster reaction that formed HONO. These clusters exhibited additional weak, broad bands between 3200 and 3400 cm-1 and two new minor photodissociation channels, loss of HONO and loss of two H2O molecules. The reaction appeared to go to completion within the n=5 clusters. The primary dissociation channel was loss of HONO, and seven vibrational bands were observed. From an analysis of the spectrum, we concluded that the n=5 cluster rearranged to form H3O+(H2O)3(HONO), i.e., an adduct of the reaction products.

The interaction of NO2 with BaO: from cooperative adsorption to Ba(NO3)2 formation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yi, Cheol-Woo W.; Kwak, Ja Hun; Szanyi, Janos

2007-10-25

The effect of water on the morphology of BaO/Al2O3-based NOx storage materials was investigated using Fourier transform infrared spectroscopy, temperature programmed desorption, and time-resolved synchrotron X-ray diffraction techniques. The results of this multi-spectroscopy study reveal that, in the presence of water, surface Ba-nitrates convert to bulk nitrates, and water facilitates the formation of large Ba(NO3)2 particles. The conversion of surface to bulk Ba-nitrates is completely reversible, i.e. after the removal of water from the storage material a significant fraction of the bulk nitrates re-convert to surface nitrates. NO2 exposure of a H2O-containing (wet) BaO/Al2O3 sample results in the formation ofmore » nitrites and bulk nitrates exclusively, i.e. no surface nitrates form. After further exposure to NO2, the nitrites completely convert to bulk nitrates. The amount of NOx taken up by the storage material is, however, essentially unaffected by the presence of water, regardless of whether the water was dosed prior to or after NO2 exposure. Based on the results of this study we are now able to explain most of the observations reported in the literature on the effect of water on NOx uptake on similar storage materials.« less

The effect of H2O on the adsorption of NO2 on γ-Al2O3: an in situ FTIR/MS study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szanyi, Janos; Kwak, Ja Hun; Chimentao, Ricardo J.

2007-02-15

The effect of water on the adsorption of NO2 onto a γ-Al2O3 catalyst support surface was investigated using Fourier transform infrared spectroscopy (FTIR) and mass spectrometry (MS). Upon room temperature exposure of the alumina surface to small amounts of NO2, nitrites and nitrates are formed, and at higher NO2 doses only nitrates are observed. The surface nitrates formed were of bridging monodentate, bridging bidentate, and monodentate configuration. At elevated NO2 pressures, the surface hydroxyls were consumed in their reaction with NO2 giving primarily bridge-bound nitrates. A significant amount of weakly adsorbed N2O3 was seen as well. Exposure of the NO2-saturatedmore » γ-Al2O3 surface to H2O resulted in the desorption of some NO2 + NO as H2O interacted with the weakly-held N2O3, while the bridging monodentate surface nitrates converted into monodentate nitrates. The conversion of these oxide-bound nitrates to water-solvated nitrates was observed at high water doses when the presence of liquid-like water is expected on the surface. The addition of H2O to the NO2-saturated γ-Al2O3 did not affect the amount of NOx strongly adsorbed on the support surface. In particular, no NOx desorption was observed when the NO2-saturated sample was heated to 573K prior to room temperature H2O exposure. The effect of water is completely reversible; i.e., during TPD experiments following NO2 and H2O coadsorption, the same IR spectra were observed at temperatures above that required for H2O desorption as seen for NO2 adsorption only experiments.« less

What is Eating Ozone? Thermal Reactions between SO2 And O3: Implications for Icy Environments

NASA Technical Reports Server (NTRS)

Loeffler, Mark J.; Hudson, Reggie L.

2016-01-01

Laboratory studies are presented, showing for the first time that thermally driven reactions in solid H2O+SO2+O3 mixtures can occur below 150 K, with the main sulfur-containing product being bisulfate (HSO4(-)). Using a technique not previously applied to the low-temperature kinetics of either interstellar or solar system ice analogs, we estimate an activation energy of 32 kJ per mol for HSO4(-) formation. These results show that at the temperatures of the Jovian satellites, SO2 and O3 will efficiently react making detection of these molecules in the same vicinity unlikely. Our results also explain why O3 has not been detected on Callisto and why the SO2 concentration on Callisto appears to be highest on that world's leading hemisphere. Furthermore, our results predict that the SO2 concentration on Ganymede will be lowest in the trailing hemisphere, where the concentration of O3 is the highest. Our work suggests that thermal reactions in ices play a much more important role in surface and sub-surface chemistry than generally appreciated, possibly explaining the low abundance of sulfur-containing molecules and the lack of ozone observed in comets and interstellar ices.

Gas-Phase Ozonolysis of Cycloalkenes: Formation of Highly Oxidized RO2 Radicals and Their Reactions with NO, NO2, SO2, and Other RO2 Radicals.

PubMed

Berndt, Torsten; Richters, Stefanie; Kaethner, Ralf; Voigtländer, Jens; Stratmann, Frank; Sipilä, Mikko; Kulmala, Markku; Herrmann, Hartmut

2015-10-15

The gas-phase reaction of ozone with C5-C8 cycloalkenes has been investigated in a free-jet flow system at atmospheric pressure and a temperature of 297 ± 1 K. Highly oxidized RO2 radicals bearing at least 5 O atoms in the molecule and their subsequent reaction products were detected in most cases by means of nitrate-CI-APi-TOF mass spectrometry. Starting from a Criegee intermediate after splitting-off an OH-radical, the formation of these RO2 radicals can be explained via an autoxidation mechanism, meaning RO2 isomerization (ROO → QOOH) and subsequently O2 addition (QOOH + O2 → R'OO). Time-dependent RO2 radical measurements concerning the ozonolysis of cyclohexene indicate rate coefficients of the intramolecular H-shifts, ROO → QOOH, higher than 1 s(-1). The total molar yield of highly oxidized products (predominantly RO2 radicals) from C5-C8 cycloalkenes in air is 4.8-6.0% affected with a calibration uncertainty by a factor of about two. For the most abundant RO2 radical from cyclohexene ozonolysis, O,O-C6H7(OOH)2O2 ("O,O" stands for two O atoms arising from the ozone attack), the determination of the rate coefficients of the reaction with NO2, NO, and SO2 yielded (1.6 ± 0.5) × 10(-12), (3.4 ± 0.9) × 10(-11), and <10(-14) cm(3) molecule(-1) s(-1), respectively. The reaction of highly oxidized RO2 radicals with other peroxy radicals (R'O2) leads to detectable accretion products, RO2 + R'O2 → ROOR' + O2, which allows to acquire information on peroxy radicals not directly measurable with the nitrate ionization technique applied here. Additional experiments using acetate as the charger ion confirm conclusively the existence of highly oxidized RO2 radicals and closed-shell products. Other reaction products, detectable with this ionization technique, give a deeper insight in the reaction mechanism of cyclohexene ozonolysis.

Determination of the Rate Coefficients of the SO2 plus O plus M yields SO3 plus M Reaction

NASA Technical Reports Server (NTRS)

Hwang, S. M.; Cooke, J. A.; De Witt, K. J.; Rabinowitz, M. J.

2010-01-01

Rate coefficients of the title reaction R(sub 31) (SO2 +O+M yields SO3 +M) and R(sub 56) (SO2 + HO2 yields SO3 +OH), important in the conversion of S(IV) to S(VI),were obtained at T =970-1150 K and rho (sub ave) = 16.2 micro mol/cubic cm behind reflected shock waves by a perturbation method. Shock-heated H2/ O2/Ar mixtures were perturbed by adding small amounts of SO2 (1%, 2%, and 3%) and the OH temporal profiles were then measured using laser absorption spectroscopy. Reaction rate coefficients were elucidated by matching the characteristic reaction times acquired from the individual experimental absorption profiles via simultaneous optimization of k(sub 31) and k(sub 56) values in the reaction modeling (for satisfactory matches to the observed characteristic times, it was necessary to take into account R(sub 56)). In the experimental conditions of this study, R(sub 31) is in the low-pressure limit. The rate coefficient expressions fitted using the combined data of this study and the previous experimental results are k(sub 31,0)/[Ar] = 2.9 10(exp 35) T(exp ?6.0) exp(?4780 K/T ) + 6.1 10(exp 24) T(exp ?3.0) exp(?1980 K/T ) cm(sup 6) mol(exp ?2)/ s at T = 300-2500 K; k(sub 56) = 1.36 10(exp 11) exp(?3420 K/T ) cm(exp 3)/mol/s at T = 970-1150 K. Computer simulations of typical aircraft engine environments, using the reaction mechanism with the above k(sub 31,0) and k(sub 56) expressions, gave the maximum S(IV) to S(VI) conversion yield of ca. 3.5% and 2.5% for the constant density and constant pressure flow condition, respectively. Moreover, maximum conversions occur at rather higher temperatures (?1200 K) than that where the maximum k(sub 31,0) value is located (approximately 800 K). This is because the conversion yield is dependent upon not only the k(sup 31,0) and k(sup 56) values (production flux) but also the availability of H, O, and HO2 in the system (consumption flux).

"Hidden" O(2) and SO(2) symmetry in lepton mixing

NASA Astrophysics Data System (ADS)

Heeck, Julian; Rodejohann, Werner

2012-02-01

To generate the minimal neutrino Majorana mass matrix that has a free solar mixing angle and Δ m_{{^{text{sol}}}}^2 = 0 it suffices to implement an O(2) symmetry, or one of its subgroups SO(2), ZN ≥3, or DN ≥3. This O(2) generalizes the hidden {text{Z}}_{{^{{2}}}}^s of lepton mixing and leads in addition automatically to μ-τ symmetry. Flavor-democratic perturbations, as expected e.g. from the Planck scale, then result in tri-bimaximal mixing. We present a minimal model with three Higgs doublets implementing a type-I seesaw mechanism with a spontaneous breakdown of the symmetry, leading to large θ 13 and small Δ m_{{^{text{sol}}}}^2 = 0 due to the particular decomposition of the perturbations under μ-τ symmetry.

Rb3In(H2O)Si5O13: a novel indium silicate with a CdSO4-topological-type structure.

PubMed

Hung, Ling-I; Wang, Sue-Lein; Chen, Chia-Yi; Chang, Bor-Chen; Lii, Kwang-Hwa

2005-05-02

A novel indium silicate, Rb3In(H2O)Si5O13, has been synthesized using a high-temperature, high-pressure hydrothermal method and characterized by single-crystal X-ray diffraction. The structure consists of five-membered rings of corner-sharing SiO4 tetrahedra connected via corner sharing to four adjacent five-membered rings to form a 3D silicate framework that belongs to the CdSO4 topological type. The InO6 octahedron shares five of its corners with five different SiO4 tetrahedra to form a 3D frame-work that delimits two types of channels to accommodate the rubidium cations. The sixth corner of InO6 is coordinated H2O. The structure is related to that of the titanium silicate ETS-10, and these are the only two metal silicates that have the CdSO4-topological-type structure. In addition, the crystal of Rb3In(H2O)Si5O13 shows an intense second harmonic generation signal. Crystal data: H2Rb3InSi5O14, monoclinic, space group Cc (No. 9), a = 9.0697(5) A, b = 11.5456(6) A, c = 13.9266(8) A, beta = 102.300(1) degrees, V = 1424.8(1) A3, and Z = 4.

Bobjonesite, V4+ O (SO4) (H2O 3, a new mineral species from Temple Mountain, Emery County, Utah, U.S.A

USGS Publications Warehouse

Schindler, M.; Hawthorne, F.C.; Huminicki, D.M.C.; Haynes, P.; Grice, Joel D.; Evans, H.T.

2003-01-01

Bobjonesite, V4+ O (SO4) (H2O 3, is a new mineral species from Temple Mountain, Emery County, Utah, U.S.A. It occurs as blue-green crusts and efflorescences in fractures in a fossil (Triassic) tree: individual crystals are ??1 mm and are intimately intergrown. Bobjonesite hydrates very easily, and is unstable in all but the driest atmosphere. Its structure was determined on a crystal of bobjonesite: however, the physical properties, optical properties and X-ray powder-diffraction pattern were recorded on the synthetic equivalent, and an electron-microprobe analysis was not possible. Bobjonesite has a pale blue streak, a vitreous luster and no observable fluorescence under ultraviolet light. It has no cleavage or parting. The Mohs hardness is ???1, and the calculated density is 2.28 g/cm3. Bobjonesite is biaxial positive, with ?? 1.555(2 , ?? 1.561(1), ?? 1.574(2), 2V(obs.) = 72(1)??, 2V(calc.) = 69??; it is non-pleochroic, X = b, Y ??? 19?? (in ?? obtuse). Bobjonesite is monoclinic, space group P21/n, cell dimensions from single-crystal data: a 7.3940(5), b 7.4111(3), c 12.0597(9) A??, ?? 106.55(1)??, V 633.5(1) A??3, Z=4. The strongest seven lines in the X-ray powder-diffraction pattern [d in A??(I)(hkl)] are as follows: 5.795(100)(002), 3.498(90)(112), 3.881(48)(1??03), 5.408(37) (101), 4.571(20)(012), 6.962(11 (1??01) and 6.254(11)(011). The chemical formula was derived from crystal-structure analysis; the end-member formula is V O (SO4) (H2O)3. The crystal structure of bobjonesite was refined to an R index of 3.6% for 1105 observed (Fo> 5??F) reflections measured with an automated four-circle X-ray diffractometer using MoK?? X-radiation. There is one V site occupied by V4+ and surrounded by three O atoms and three (H2O) groups in an octahedral arrangement, with one short vanadyl bond (1.577 A??), four similar equatorial bonds (<2.022 A??), and one longer V-O bond (2.278 A??) trans to the vanadyl bond. The structure consists of isolated [V4+2 O2 (H2O)6 (SO4)2

ON THE REACTION OF COMPONENETS IN MeNO$sub 3$-UO$sub 2$(NO$sub 3$)$sub 2$- H$sub 2$O TYPE SYSTEMS (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yakimov, M.A.; Nosova, N.F.; Degtyarev, A.Ya.

1963-01-01

Solubility in ternary systems TlNO/sub 3/--UO/sub 2/(NO/sub 3/)/sub 2/-- H/sub 2/ O and CsNO/sub 3/--UO/sub 2/(NO/sub 3/)/sub 2/--H/sub 2/O at 0 to 25 c- C was studi ed by the isothermal method. The first system did not form solid phase compounds; the second system formed two compounds Cs/sub 2/UO/ sub 2/(NO/sub 3/)/sub 4/ and CsUO/sub 2/(NO/sub 3/)/sub 3/ at 25 c- and of water vapor pressure over the systems at 25 c- showed that water activity in the ternary systems at certain concentrations does not exceed the water activity in binary uranyl nitratewater system (at identical uranyl nitrate concentrations) confirmingmore » the observed complex formation in the solution. The mechanism of complex formation was analyzed and expanded for alkali metal - metal salt-complexing agent water systems. (R.V.J.)« less

Inter-conversion of Chromium Species During Air Sampling: Effects of O3, NO2, SO2, Particle Matrices, Temperature and Humidity

PubMed Central

Huang, Lihui; Fan, Zhihua (Tina); Yu, Chang Ho; Hopke, Philip K.; Lioy, Paul J.; Buckley, Brian T.; Lin, Lin; Ma, Yingjun

2013-01-01

The inter-conversion between Cr(VI), a pulmonary carcinogen, and Cr(III), an essential human nutrient, poses challenges to the measurement of Cr(VI) in airborne particles. Chamber and field tests were conducted to identify the factors affecting Cr(VI)-Cr(III) inter-conversion in the basic filter medium under typical sampling conditions. In the chamber tests, isotopically enriched 53Cr(VI) and 50Cr(III) were spiked on diesel particulate matter (DPM) and secondary organic aerosol (SOA) that were pre-collected on a basic MCE filter. The filter samples were then exposed to clean air or the air containing SO2 (50 and 160 ppb), 100 ppb O3, or 150 ppb NO2 for 24 hours at 16.7 LPM flow rate at designated temperature (20 and 31°C) and RH (40% and 70%) conditions. Exposure to 160 ppb SO2 had the greatest effect on 53Cr(VI) reduction, with 53Cr(VI) recovery of 31.7 ± 15.8% (DPM) and 42.0 ± 7.9% (SOA). DPM and SOA matrix induced 53Cr(VI) reduction when exposed to clean air while reactive oxygen species in SOA could promote 50Cr(III) oxidation. Deliquescence when RH increased from 40% to 70% led to conversion of Cr(III) in SOA, whereas oxidized organics in DPM and SOA enhanced hygroscopicity and thus facilitated Cr(VI) reduction. Field tests showed seasonal variation of Cr(VI)-Cr(III) inter-conversion during sampling. Correction of the inter-conversion using USEPA method 6800 is recommended to improve accuracy of ambient Cr(VI) measurements. PMID:23550818

Novel Process of Simultaneous Removal of Nitric Oxide and Sulfur Dioxide Using a Vacuum Ultraviolet (VUV)-Activated O2/H2O/H2O2 System in A Wet VUV-Spraying Reactor.

PubMed

Liu, Yangxian; Wang, Qian; Pan, Jianfeng

2016-12-06

A novel process for NO and SO 2 simultaneous removal using a vacuum ultraviolet (VUV, with 185 nm wavelength)-activated O 2 /H 2 O/H 2 O 2 system in a wet VUV-spraying reactor was developed. The influence of different process variables on NO and SO 2 removal was evaluated. Active species (O 3 and ·OH) and liquid products (SO 3 2- , NO 2 - , SO 4 2- , and NO 3 - ) were analyzed. The chemistry and routes of NO and SO 2 removal were investigated. The oxidation removal system exhibits excellent simultaneous removal capacity for NO and SO 2 , and a maximum removal of 96.8% for NO and complete SO 2 removal were obtained under optimized conditions. SO 2 reaches 100% removal efficiency under most of test conditions. NO removal is obviously affected by several process variables. Increasing VUV power, H 2 O 2 concentration, solution pH, liquid-to-gas ratio, and O 2 concentration greatly enhances NO removal. Increasing NO and SO 2 concentration obviously reduces NO removal. Temperature has a dual impact on NO removal, which has an optimal temperature of 318 K. Sulfuric acid and nitric acid are the main removal products of NO and SO 2 . NO removals by oxidation of O 3 , O·, and ·OH are the primary routes. NO removals by H 2 O 2 oxidation and VUV photolysis are the complementary routes. A potential scaled-up removal process was also proposed initially.

Establishment of a novel advanced oxidation process for economical and effective removal of SO2 and NO.

PubMed

Hao, Runlong; Zhao, Yi; Yuan, Bo; Zhou, Sihan; Yang, Shuo

2016-11-15

SO2 and NO have caused serious haze in China. For coping with the terrible problem, this paper proposed a novel advanced oxidation process of ultraviolet (UV) catalyzing vaporized H2O2 for simultaneous removal of SO2 and NO. Effects of various factors on simultaneous removal of SO2 and NO were investigated, such as the mass concentration of H2O2, the UV energy density, the UV wavelength, the H2O2 pH, the temperatures of H2O2 vaporization and UV-catalysis, the flue gas residence time, the concentrations of SO2, NO and O2, and radical scavenger. The removal efficiencies of 100% for SO2 and 87.8% for NO were obtained under the optimal conditions. The proposed approach has some superiorities, i.e. less dosage and high utilization of oxidant, short flue gas residence time and inhibiting the competition between SO2 and NO for oxidants. The results indicated that the desulfurization process was dominated by the absorption by HA-Na, whereas the denitrification was primarily affected by the H2O2 dosage, UV energy density and H2O2 pH. Interestingly, an appropriate amount of SO2 was beneficial for NO removal. The reaction mechanism was speculated based on the characterizations of removal products by XRD, FT-IR and IC. Copyright © 2016. Published by Elsevier B.V.

NO and NO2 Sensing Properties of WO3 and Co3O4 Based Gas Sensors

PubMed Central

Akamatsu, Takafumi; Itoh, Toshio; Izu, Noriya; Shin, Woosuck

2013-01-01

Semiconductor-based gas sensors that use n-type WO3 or p-type Co3O4 powder were fabricated and their gas sensing properties toward NO2 or NO (0.5–5 ppm in air) were investigated at 100 °C or 200 °C. The resistance of the WO3-based sensor increased on exposure to NO2 and NO. On the other hand, the resistance of the Co3O4-based sensor varied depending on the operating temperature and the gas species. The chemical states of the surface of WO3 or those of the Co3O4 powder on exposure to 1 ppm NO2 and NO were investigated by diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy. No clear differences between the chemical states of the metal oxide surface exposed to NO2 or NO could be detected from the DRIFT spectra. PMID:24048338

Rate constant for the reaction SO + BrO yields SO2 + Br

NASA Technical Reports Server (NTRS)

Brunning, J.; Stief, L.

1986-01-01

The rate of the radical-radical reaction SO + BrO yields SO2 + Br has been determined at 298 K in a discharge flow system near 1 torr pressure with detection of SO and BrO via collision-free sampling mass spectrometry. The rate constant was determined using two different methods: measuring the decay of SO radicals in the presence of an excess of BrO and measuring the decay of BrO radicals in excess SO. The results from the two methods are in reasonable agreement and the simple mean of the two values gives the recommended rate constant at 298 K, k = (5.7 + or - 2.0) x 10 to the -11th cu cm/s. This represents the first determination of this rate constant and it is consistent with a previously derived lower limit based on SO2 formation. Comparison is made with other radical-radical reactions involving SO or BrO. The reaction SO + BrO yields SO2 + Br is of interest for models of the upper atmosphere of the earth and provides a potential coupling between atmospheric sulfur and bromine chemistry.

Design of multi-shell Fe2O3@MnOx@CNTs for the selective catalytic reduction of NO with NH3: improvement of catalytic activity and SO2 tolerance

NASA Astrophysics Data System (ADS)

Cai, Sixiang; Hu, Hang; Li, Hongrui; Shi, Liyi; Zhang, Dengsong

2016-02-01

Manganese based catalysts are highly active in the NH3-SCR reaction for NOx removal. Unfortunately, manganese oxides can be easily deactivated by sulfur dioxide in the flow gas, which has become the main obstacle for their practical applications. To address this problem, we presented a green and facile method for the synthesis of multi-shell Fe2O3@MnOx@CNTs. The morphology and structural properties of the catalysts were systematically investigated. The results revealed that the MnOx@CNT core-shell structure was formed during the chemical bath deposition, while the outermost MnOx species were transformed to Fe2O3 after the galvanic replacement reaction. The formation of the multi-shell structure induced the enhancement of the active oxygen species, reducible species as well as adsorption of the reactants, which brought about excellent de-NOx performance. Moreover, the Fe2O3 shell could effectively suppress the formation of the surface sulfate species, leading to the desirable SO2 resistance to the multi-shell catalyst. Hence, the synthesis protocol could provide guidance for the preparation and elevation of manganese based catalysts.Manganese based catalysts are highly active in the NH3-SCR reaction for NOx removal. Unfortunately, manganese oxides can be easily deactivated by sulfur dioxide in the flow gas, which has become the main obstacle for their practical applications. To address this problem, we presented a green and facile method for the synthesis of multi-shell Fe2O3@MnOx@CNTs. The morphology and structural properties of the catalysts were systematically investigated. The results revealed that the MnOx@CNT core-shell structure was formed during the chemical bath deposition, while the outermost MnOx species were transformed to Fe2O3 after the galvanic replacement reaction. The formation of the multi-shell structure induced the enhancement of the active oxygen species, reducible species as well as adsorption of the reactants, which brought about excellent de

Pb4(BO3)2(SO4) and Pb2[(BO2)(OH)](SO4): New lead(II) borate-sulfate mixed-anion compounds with two types of 3D network structures

NASA Astrophysics Data System (ADS)

Ruan, Ting-Ting; Wang, Wen-Wen; Hu, Chun-Li; Xu, Xiang; Mao, Jiang-Gao

2018-04-01

Two new lead(II) borate-sulfate mixed-anion compounds, namely, Pb4(BO3)2(SO4) and Pb2[(BO2)(OH)](SO4), have been prepared by using high-temperature melt method or hydrothermal reaction. These compounds exhibit two different types of 3D structures composed of the same anionic units of BO3 triangles and SO4 tetrahedra which are interconnected by lead(II) cations. In Pb4(BO3)2(SO4), the lead(II) ions are bridged by borate anions into 3D [Pb4(BO3)2]2+ architectures with 1D tunnels of 8-member rings along the a-axis, which are filled by the sulfate anions. In Pb2[(BO2)(OH)](SO4), the lead(II) ions are interconnected by borate and sulfate anions into 2D Pb-B-O and Pb-S-O layers parallel to the ab plane, respectively, and these layers are further condensed into the 3D lead(II) borate-sulfate framework. TGA and DSC studies indicate that Pb4(BO3)2(SO4) is congruently melting with a melting point of 689 °C whereas Pb2[(BO2)(OH)](SO4) decomposes at approximately 335 °C. UV/Vis/NIR optical diffuse reflectance spectrum measurements reveal the optical band gaps of 4.03 and 4.08 eV for Pb4(BO3)2(SO4) and Pb2[(BO2)(OH)](SO4), respectively. Furthermore, the electronic structures of Pb4(BO3)2(SO4) have also been calculated.

Reflected shock tube studies of high-temperature rate constants for OH + CH4 --> CH3 + H2O and CH3 + NO2 --> CH3O + NO.

PubMed

Srinivasan, N K; Su, M-C; Sutherland, J W; Michael, J V

2005-03-10

The reflected shock tube technique with multipass absorption spectrometric detection of OH radicals at 308 nm has been used to study the reactions OH + CH(4) --> CH(3) + H(2)O and CH(3) + NO(2) --> CH(3)O + NO. Over the temperature range 840-2025 K, the rate constants for the first reaction can be represented by the Arrhenius expression k = (9.52 +/- 1.62) x 10(-11) exp[(-4134 +/- 222 K)/T] cm(3) molecule(-1) s(-1). Since this reaction is important in both combustion and atmospheric chemistry, there have been many prior investigations with a variety of techniques. The present results extend the temperature range by 500 K and have been combined with the most accurate earlier studies to derive an evaluation over the extended temperature range 195-2025 K. A three-parameter expression describes the rate behavior over this temperature range, k = (1.66 x 10(-18))T(2.182) exp[(-1231 K)/T] cm(3) molecule(-1) s(-1). Previous theoretical studies are discussed, and the present evaluation is compared to earlier theoretical estimates. Since CH(3) radicals are a product of the reaction and could cause secondary perturbations in rate constant determinations, the second reaction was studied by OH radical production from the fast reactions CH(3)O --> CH(2)O + H and H + NO(2) --> OH + NO. The measured rate constant is 2.26 x 10(-11) cm(3) molecule(-1) s(-1) and is not dependent on temperature from 233 to 1700 K within experimental error.

The reaction of H2O2 with NO2 and NO

NASA Technical Reports Server (NTRS)

Gray, D.; Lissi, E.; Heicklen, J.

1972-01-01

The reactions of NO and NO2 with H2O2 have been examined at 25 C. Reaction mixtures were monitored by continuously bleeding through a pinhole into a monopole mass spectrometer. NO2 was also monitored by its optical absorption in the visible part of the spectrum. Reaction mixtures containing initially 1.5 - 2.5 torr of NO2 and 0.8 - 1.4 torr of H2O2 or 1 - 12 torr of NO and 0.5 - 1.5 torr of H2O2 were studied. The H2O2 - NO reaction was complex. There was an induction period followed by a marked acceleration in reactant removal. The final products of the reaction, NO2, probably H2O, and possibly HONO2 were produced mainly after all the H2O2 was removed. The HONO intermediate was shown to disproportionate to NO2 + NO + H2O in a relatively slow first order reaction. The acceleration in H2O2 removal after the NO - H2O2 reaction is started is caused by NO2 catalysis.

Fabrication and luminescent properties of La2O2S:Eu3+ translucent ceramic by pressureless reaction sintering

NASA Astrophysics Data System (ADS)

Lian, Jingbao; Wang, Bingxin; Liang, Ping; Liu, Feng; Wang, Xuejiao

2014-04-01

La2O2S:Eu3+ translucent ceramic (LOS:Eu) was fabricated by pressureless reaction sintering method. It is found that the (La, Eu)2(OH)4SO4ṡ2H2O precursor is synthesized by co-precipitation using commercially available La(NO3)3, Eu(NO3)3, (NH4)2SO4 and NH3ṡH2O as the starting materials. And this precursor can be converted into pure La2O2SO4:Eu3+ phosphor by calcination at 800 °C for 1 h in air, which is composed of a few small needle agglomerated particles. Then the La2O2SO4:Eu3+ phosphor compact can be sintered into the LOS:Eu at 1500 °C for 2 h in the hybrid atmosphere of flowing hydrogen and argon. Under 387 nm UV light excitation, the LOS:Eu reveals a red light emission at 628 nm as the most prominent peak, which corresponds to the 5D0 → 7F2 transition of Eu3+ ions.

A novel amido-pyrophosphate Mn(II) chelate complex with the synthetic ligand O{P(O)[NHC(CH3)3]2}2 (L): [Mn(L)2{OC(H)N(CH3)2}2]Cl2·2H2O.

PubMed

Tarahhomi, Atekeh; Pourayoubi, Mehrdad; Fejfarová, Karla; Dušek, Michal

2013-03-01

The title complex, trans-bis(dimethylformamide-κO)bis{N,N'-N'',N'''-tetra-tert-butyl[oxybis(phosphonic diamide-κO)]}manganese(II) dichloride dihydrate, [Mn(C16H40N4O3P2)2(C3H7NO)2]Cl2·2H2O, is the first example of a bis-chelate amido-pyrophosphate (pyrophosphoramide) complex containing an O[P(O)(NH)2]2 fragment. Its asymmetric unit contains half of the complex dication, one chloride anion and one water molecule. The Mn(II) atom, located on an inversion centre, is octahedrally coordinated, with a slight elongation towards the monodentate dimethylformamide ligand. Structural features of the title complex, such as the P=O bond lengths and the planarity of the chelate ring, are compared with those of previously reported complexes with six-membered chelates involving the fragments C(O)NHP(O), (X)NP(O) [X = C(O), C(S), S(O)2 and P(O)] and O[P(O)(N)2]2. This analysis shows that the six-membered chelate rings are less puckered in pyrophosphoramide complexes containing a P(O)OP(O) skeleton, such as the title compound. The extended structure of the title complex involves a linear aggregate mediated by N-H...O and N-H...Cl hydrogen bonds, in which the chloride anion is an acceptor in two additional O-H...Cl hydrogen bonds.

Effect of metal oxides and black carbon (soot) on SO[sub 2]/O[sub 2]/H[sub 2]O reaction systems

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chughtai, A.R.; Brooks, M.E.; Smith, D.M.

1993-08-01

Particulates of atmospheric interest, including soot, oxidized soot, and oxides of transition metals, [open quotes]fellow travelers[close quotes] in the combustion of solid or liquid fossil fuels, have been examined for their influence on the heterogeneous oxidation of S(IV) to S(VI), both with and without the presence of simulated solar radiation. Under all conditions, MnO[sub 2] has been found to be the most active of the materials in this study. Effectiveness for the oxidation of SO[sub 2] in the presence of oxygen and water vapor decreases in the order: MnO[sub 2] [much gt] V[sub 2]O[sub 5] > CuO > Fe[sub 2]O[submore » 3] > Al[sub 2]O[sub 3] > Soot > TiO[sub 2] = SiO[sub 2] (cab-o-sil) [approximately] ZnO > ozonized soot = blank. The oxidation of SO[sub 2] also was carried out in the presence of soot-MnO[sub 2], soot-V[sub 2]O[sub 5], and soot-Fe[sub 2]O[sub 3] mixtures. The respective sulfate yields were found to be significantly higher than those obtained under similar conditions for the individual substrates. Other combinations, such as MnO[sub 2]/V[sub 2]O[sub 5] and MnO[sub 2]/Fe[sub 2]O[sub 3], yielded sulfate at levels higher than those obtained by any of the transition metal oxides or other oxide mixtures used. The mixing ratio of 1:0.75 (wt/wt) in the MnO[sub 2]/V[sub 2]O[sub 5] mixture was found to be optimum. With this mixture the sulfate yield was nearly twice the amount obtained if only MnO[sub 2] was used and nearly four times the amount if V[sub 2]O[sub 5] was used alone. Extensive analyses of the optimum mixture, to detect any unique identity, were inconclusive. 49 refs., 9 figs.« less

Reactions of small negative ions with O2(a 1[Delta]g) and O2(X 3[Sigma]g-)

NASA Astrophysics Data System (ADS)

Midey, Anthony; Dotan, Itzhak; Seeley, J. V.; Viggiano, A. A.

2009-02-01

The rate constants and product ion branching ratios were measured for the reactions of various small negative ions with O2(X 3[Sigma]g-) and O2(a 1[Delta]g) in a selected ion flow tube (SIFT). Only NH2- and CH3O- were found to react with O2(X) and both reactions were slow. CH3O- reacted by hydride transfer, both with and without electron detachment. NH2- formed both OH-, as observed previously, and O2-, the latter via endothermic charge transfer. A temperature study revealed a negative temperature dependence for the former channel and Arrhenius behavior for the endothermic channel, resulting in an overall rate constant with a minimum at 500 K. SF6-, SF4-, SO3- and CO3- were found to react with O2(a 1[Delta]g) with rate constants less than 10-11 cm3 s-1. NH2- reacted rapidly with O2(a 1[Delta]g) by charge transfer. The reactions of HO2- and SO2- proceeded moderately with competition between Penning detachment and charge transfer. SO2- produced a SO4- cluster product in 2% of reactions and HO2- produced O3- in 13% of the reactions. CH3O- proceeded essentially at the collision rate by hydride transfer, again both with and without electron detachment. These results show that charge transfer to O2(a 1[Delta]g) occurs readily if the there are no restrictions on the ion beyond the reaction thermodynamics. The SO2- and HO2- reactions with O2(a) are the only known reactions involving Penning detachment besides the reaction with O2- studied previously [R.S. Berry, Phys. Chem. Chem. Phys., 7 (2005) 289-290].

Model simulation of NO3, N2O5 and ClNO2 at a rural site in Beijing during CAREBeijing-2006

NASA Astrophysics Data System (ADS)

Wang, Haichao; Lu, Keding; Tan, Zhaofeng; Sun, Kang; Li, Xin; Hu, Min; Shao, Min; Zeng, Limin; Zhu, Tong; Zhang, Yuanhang

2017-11-01

A chemical box model was used to study nitrate radical (NO3), dinitrogen pentoxide (N2O5) and nitryl chloride (ClNO2) in a rural site during the Campaign of Air Quality Research in Beijing 2006 (CAREBeijing-2006). The model was based on regional atmospheric chemistry mechanism version 2 (RACM2) with the heterogeneous uptake of N2O5 and the simplified chloride radical (Cl) chemistry mechanism. A high production rate of NO3 with a mean value of 0.8 ppbv/h and low mixing ratios of NO3 and N2O5 (peak values of 17 pptv and 480 pptv, respectively) existed in this site. Budget analysis showed that NO emission suppressed the NO3 chemistry at the surface layer, the reaction of NO3 with VOCs made a similar contribution to NO3 loss as N2O5 heterogeneous uptake. The NO3 chemistry was predominantly controlled by isoprene, and NO3 oxidation produced organic nitrate with a mean value of 0.06 ppbv/h during nighttime. The organic nitrate production initiated by NO3 was equal to that initiated by OH, implying the importance of nighttime chemistry for secondary organic aerosol (SOA) formation. We confirmed that the N2O5 heterogeneous reaction accounted for nighttime particle NO3- enhancement, with a large day to day variability, and made less of a contribution to NOx loss compared to that of OH reacting with NO2. Additionally, abundant ClNO2, up to 5.0 ppbv, was formed by N2O5 heterogeneous uptake. ClNO2 was sustained at a high level until noon in spite of the gradually increasing photolysis of ClNO2 after sunrise. Chlorine activation caused by N2O5 heterogeneous uptake increased primary ROx formation by 5% and accounted for 8% of the net ozone production enhancement in the morning.

Atmospheric isoprene ozonolysis: impacts of stabilised Criegee intermediate reactions with SO2, H2O and dimethyl sulfide

NASA Astrophysics Data System (ADS)

Newland, M. J.; Rickard, A. R.; Vereecken, L.; Muñoz, A.; Ródenas, M.; Bloss, W. J.

2015-08-01

Isoprene is the dominant global biogenic volatile organic compound (VOC) emission. Reactions of isoprene with ozone are known to form stabilised Criegee intermediates (SCIs), which have recently been shown to be potentially important oxidants for SO2 and NO2 in the atmosphere; however the significance of this chemistry for SO2 processing (affecting sulfate aerosol) and NO2 processing (affecting NOx levels) depends critically upon the fate of the SCIs with respect to reaction with water and decomposition. Here, we have investigated the removal of SO2 in the presence of isoprene and ozone, as a function of humidity, under atmospheric boundary layer conditions. The SO2 removal displays a clear dependence on relative humidity, confirming a significant reaction for isoprene-derived SCIs with H2O. Under excess SO2 conditions, the total isoprene ozonolysis SCI yield was calculated to be 0.56 (±0.03). The observed SO2 removal kinetics are consistent with a relative rate constant, k(SCI + H2O) / k(SCI + SO2), of 3.1 (±0.5) × 10-5 for isoprene-derived SCIs. The relative rate constant for k(SCI decomposition) / k(SCI+SO2) is 3.0 (±3.2) × 1011 cm-3. Uncertainties are ±2σ and represent combined systematic and precision components. These kinetic parameters are based on the simplification that a single SCI species is formed in isoprene ozonolysis, an approximation which describes the results well across the full range of experimental conditions. Our data indicate that isoprene-derived SCIs are unlikely to make a substantial contribution to gas-phase SO2 oxidation in the troposphere. We also present results from an analogous set of experiments, which show a clear dependence of SO2 removal in the isoprene-ozone system as a function of dimethyl sulfide concentration. We propose that this behaviour arises from a rapid reaction between isoprene-derived SCIs and dimethyl sulfide (DMS); the observed SO2 removal kinetics are consistent with a relative rate constant, k(SCI + DMS

Measurements of 32SO2, 33SO2, 34SO2 and 36SO2 high-resolution cross-sections and isotope effects by SO2 self-shielding

NASA Astrophysics Data System (ADS)

Endo, Y.; Ogawa, M.; Danielache, S. O.; Ueno, Y.

2017-12-01

Archean sulfur mass-independent fractionation (S-MIF) is a unique proxy within the geological and geochemical records for studying the composition of the Archean atmosphere. S-MIF signatures are defined as Δ33S = δ33S - 0.515×δ34S and Δ36S = δ36S - 1.90×δ34S. Archean S-MIF is characterized as Δ36S/Δ33S = -1. Recent SO2 photochemical experiments under specific reducing conditions reproduced the Archean trend for the first time [1]. Self-shielding of SO2 photolysis and intersystem crossing in excited SO2 are probably key mechanisms for explaining Archean S-MIF. Self-shielding is originated from UV spectra changed by upper SO2 own absorption. Because 32S accounts for about 95% of all sulfur isotopes, the photolysis rate constant of only 32SO2 is lower than other isotopologue. Thus, SO2 photolysis in the bottom of the atmosphere undergoes mass-independent fractionation. Fractionation factors by SO2 photolysis reaction can be calculated by absorption cross-sections of 32SO2, 33SO2, 34SO2 and 36SO2 and respective quantum yields. Quantitative estimations self-shielding fractionation factors requires high-spectral resolution cross-sections, but they have not been reported yet. Here we report measurements of high-resolution cross-sections (1cm-1) and fractionation factors by SO2 photolysis including self-shielding. Moreover, because the absorption wavelength varies with each isotopologue, photolysis rate constants of all isotopologues (32S16O2, 32S16O18O, etc) should be different. Then self-shielding may affect the ratio of isotopologues such as clumped-isotopes. We calculated preliminary calculation clumped isotope enrichment in residual species by self-shielding. Reference: [1] Endo, Y., Ueno, Y., Aoyama, S., & Danielache, S. O. (2016). Sulfur isotope fractionation by broadband UV radiation to optically thin SO2 under reducing atmosphere. EPSL, 453, 9-22.

Physical chemistry of the H2SO4/HNO3/H2O system - Implications for polar stratospheric clouds

NASA Technical Reports Server (NTRS)

Molina, M. J.; Zhang, R.; Wooldridge, P. J.; Mcmahon, J. R.; Kim, J. E.; Chang, H. Y.; Beyer, K. D.

1993-01-01

Polar stratospheric clouds (PSCs) play a key role in stratospheric ozone depletion. Surface-catalyzed reactions on PSC particles generate chlorine compounds that photolyze readily to yield chlorine radicals, which in turn destroy ozone very efficiently. The most prevalent PSCs form at temperatures several degrees above the ice frost point and are believed to consist of HNO3 hydrates; however, their formation mechanism is unclear. Results of laboratory experiments are presented which indicate that the background stratospheric H2SO4/H2O aerosols provide an essential link in this mechanism: These liquid aerosols absorb significant amounts of HNO3 vapor, leading most likely to the crystallization of nitric acid trihydrate (NAT). The frozen particles then grow to form PSCs by condensation of additional amounts of HNO3 and H2O vapor. Furthermore, reaction probability measurements reveal that the chlorine radical precursors are formed readily at polar stratospheric temperatures not just on NAT and ice crystals, but also on liquid H2SO4 solutions and on solid H2SO4 hydrates. These results imply that the chlorine activation efficiency of the aerosol particles increases rapidly as the temperature approaches the ice frost point regardless of the phase or composition of the particles.

Neutron scattering studies of K3H(SO4)2 and K3D(SO4)2: the particle-in-a-box model for the quantum phase transition.

PubMed

Fillaux, François; Cousson, Alain

2012-08-21

In the crystal of K(3)H(SO(4))(2) or K(3)D(SO(4))(2), dimers SO(4)···H···SO(4) or SO(4)···D···SO(4) are linked by strong centrosymmetric hydrogen or deuterium bonds whose O···O length is ≈2.50 Å. We address two open questions. (i) Are H or D sites split or not? (ii) Is there any structural counterpart to the phase transition observed for K(3)D(SO(4))(2) at T(c) ≈ 85.5 K, which does not exist for K(3)H(SO(4))(2)? Neutron diffraction by single-crystals at cryogenic or room temperature reveals no structural transition and no resolvable splitting of H or D sites. However, the width of the probability densities suggest unresolved splitting of the wavefunctions suggesting rigid entities H(L1/2)-H(R1/2) or D(L1/2)-D(R1/2) whose separation lengths are l(H) ≈ 0.16 Å or l(D) ≈ 0.25 Å. The vibrational eigenstates for the center of mass of H(L1/2)-H(R1/2) revealed by inelastic neutron scattering are amenable to a square-well and we suppose the same potential holds for D(L1/2)-D(R1/2). In order to explain dielectric and calorimetric measurements of mixed crystals K(3)D((1-ρ))H(ρ)(SO(4))(2) (0 ≤ ρ ≤ 1), we replace the classical notion of order-disorder by the quantum notion of discernible (e.g., D(L1/2)-D(R1/2)) or indiscernible (e.g., H(L1/2)-H(R1/2)) components depending on the separation length of the split wavefunction. The discernible-indiscernible isostructural transition at finite temperatures is induced by a thermal pure quantum state or at 0 K by ρ.

Palladium (Pd) sensitized molybdenum trioxide (MoO3) nanobelts for nitrogen dioxide (NO2) gas detection

NASA Astrophysics Data System (ADS)

Mane, A. A.; Moholkar, A. V.

2018-01-01

The MoO3 nanobelts have been grown onto the glass substrates using chemical spray pyrolysis (CSP) deposition technique at optimized substrate temperature of 400 °C. XRD study shows that the film is polycrystalline in nature and possesses an orthorhombic crystal structure. The FE-SEM micrographs show the formation of nanobelts-like morphology of MoO3. The presence of Pd and its oxidation states in Pd-sensitized MoO3 film is confirmed using EDAX and XPS study, respectively. The percentage gas response is defined as |Rg -Ra|/Ra × 100 % where, Ra and Rg are the film resistances in presence of air and analyte gas, respectively. Before Pd sensitization, MoO3 nanobelts show NO2 gas response of 68% for 100 ppm concentration at operating temperature of 200 °C with response and recovery times of 15 s and 150 s, respectively. Selectivity coefficient study shows that the Pd-sensitized MoO3 nanobelts are more sensitive and selective towards NO2 gas among various gases such as NH3, H2S, CO, CO2 and SO2. The Pd-sensitized MoO3 nanobelts shows the enhanced response of 95.3% towards 100 ppm NO2 gas concentration with response and recovery times of 74 s and 297 s, respectively. The lower detection limit is found to be 5 ppm which is four times less than immediately dangerous to life or health (IDLH) value of 20 ppm. Finally, the proposed NO2 gas sensing mechanism based on chemisorption model is discussed.

The equilibrium constant for N2O5 = NO2 + NO3 - Absolute determination by direct measurement from 243 to 397 K

NASA Technical Reports Server (NTRS)

Cantrell, C. A.; Davidson, J. A.; Mcdaniel, A. H.; Shetter, R. E.; Calvert, J. G.

1988-01-01

Direct determinations of the equilibrium constant for the reaction N2O5 = NO2 + NO3 were carried out by measuring NO2, NO3, and N2O5 using long-path visible and infrared absorption spectroscopy as a function of temperature from 243 to 397 K. The first-order decay rate constant of N2O5 was experimentally measured as a function of temperature. These results are in turn used to derive a value for the rate coefficient for the NO-forming channel in the reaction of NO3 with NO2. The implications of the results for atmospheric chemistry, the thermodynamics of NO3, and for laboratory kinetics studies are discussed.

A new cavity ring-down instrument for airborne monitoring of N2O5, NO3, NO2 and O3 in the upper troposphere lower stratosphere

NASA Astrophysics Data System (ADS)

Ruth, Albert A.; Brown, Steven S.; Dinesan, Hemanth; Dubé, William P.; Goulette, Marc; Hübler, Gerhard; Orphal, Johannes; Zahn, Andreas

2016-04-01

The chemistry of NO3 and N2O5 is important to the regulation of both tropospheric and stratospheric ozone. In situ detection of NO3 and N2O5 in the upper troposphere lower stratosphere (UTLS) represents a new scientific direction as the only previous measurements of these species in this region of the atmosphere has been via remote sensing techniques. Because both the sources and the sinks for NO3 and N2O5 are potentially stratified spatially, their mixing ratios, and their influence on nitrogen oxide and ozone transport and loss at night can show large variability as a function of altitude. Aircraft-based measurements of heterogeneous N2O5 uptake in the lower troposphere have uncovered a surprising degree of variability in the uptake coefficient [1], but there are no corresponding high altitude measurements.The UTLS is routinely sampled by the IAGOS-CARIBIC program (Civil Aircraft for the Regular Investigation of the atmosphere Based on an Instrument Container, www.caribic-atmospheric.com), a European infrastructural program with the aim of studying the chemistry and transport across this part of the atmosphere. An airfreight container with 15 different automated instruments from 8 European research partners is utilized on board a commercial Lufthansa airbus 340-600 to monitor ~ 100 atmospheric species (trace gases and aerosol parameters) in the UTLS. The instrumentation in the CARIBIC container is now to be supplemented by a new cavity ring-down device for monitoring nitrogen oxides, jointly developed by researchers from Cork (Ireland), Boulder (USA) and Karlsruhe (Germany). The compact and light-weight instrument is designed to monitor not only NO3 and N2O5, but also NO2 and O3. The detection is based on 4 high-finesse optical cavities (cavity length ~ 44 cm). Two cavities are operated at 662 nm (maximum absorption of NO3), the other two at 405 nm (maximum absorption of NO2). The inlet to one of the (662)-cavities is heated in order to thermally decompose N2O5

Two basic bismuth nitrates: [Bi6O6(OH)2](NO3)4 · 2H2O with superior photodegradation activity for rhodamine B and [Bi6O5(OH)3](NO3)5 · 3H2O with ultrahigh adsorption capacity for methyl orange

NASA Astrophysics Data System (ADS)

Pang, Jiawei; Han, Qiaofeng; Liu, Weiqi; Shen, Zichen; Wang, Xin; Zhu, Junwu

2017-11-01

A novel basic bismuth nitrate, [Bi6O6(OH)2](NO3)4·2H2O (denoted as BiON-4N), was easily obtained at room temperature in the existence of 2-methoxyethanol (CH3OCH2CH2OH; 2ME) with a pH value ranging from 4.5 to 7.0. The morphology of BiON-4N could be easily tailored by changing the variety and amount of bases like urea, hexamethylenetetramine (HMTA), NaOH and NH3·H2O. When the solution pH was decreased lower than 4.5, another basic bismuth nitrate, [Bi6O5(OH)3](NO3)5·3H2O (denoted as BiON-5N), could be synthesized. Among those, BiON-4N nanoparticles obtained with 40 mmol of HMTA exhibited superior photocatalytic activity for rhodamine B (RhB) degradation with an efficiency of 100% within 4 min of UV light irradiation, which was much higher than that of commercial TiO2 (P25). The excellent photocatalytic performance of BiON-4N was mainly attributed to higher surface area (13.1 m2 g-1) in comparison with other basic bismuth nitrates. Furthermore, the as-prepared BiON-5N revealed excellent adsorption performance for the anions like methyl orange (MO) and K2Cr2O7, and especially for MO, the maximum adsorption capacity arrived up to 730 mg g-1, which should be relevant to highly positively charged surface. This work provides a new strategy for developing bismuth-based nanomaterials in the big bismuth family as potential photocatalyst and adsorbent for the removal of dyes and contaminants.

Quenching of I(2P1/2) by NO2, N2O4, and N2O.

PubMed

Kabir, Md Humayun; Azyazov, Valeriy N; Heaven, Michael C

2007-10-11

Quenching of excited iodine atoms (I(5p5, 2P1/2)) by nitrogen oxides are processes of relevance to discharge-driven oxygen iodine lasers. Rate constants at ambient and elevated temperatures (293-380 K) for quenching of I(2P1/2) atoms by NO2, N2O4, and N2O have been measured using time-resolved I(2P1/2) --> I(2P3/2) 1315 nm emission. The excited atoms were generated by pulsed laser photodissociation of CF3I at 248 nm. The rate constants for I(2P1/2) quenching by NO2 and N2O were found to be independent of temperature over the range examined with average values of (2.9 +/- 0.3) x 10(-15) and (1.4 +/- 0.1) x 10(-15) cm3 s(-1), respectively. The rate constant for quenching of I(2P1/2) by N2O4 was found to be (3.5 +/- 0.5) x 10(-13) cm3 s(-1) at ambient temperature.

Bis[4-(4-pyridyl)pyridinium] (4-carboxy­pyridine-2,6-dicarboxyl­ato-κ3 O 2,N,O 6)(pyridine-2,4,6-tricarboxyl­ato-κ3 O 2,N,O 6)ferrate(III) trihydrate

PubMed Central

Zhao, Li; Dong, You-Ren; Xie, Hong-Zhen

2009-01-01

In the title salt, (C10H9N2)2[Fe(C8H2NO6)(C8H3NO6)]·3H2O, the FeIII atom is O,N,O′-chelated by dianionic and trianionic ligands in a slightly distorted octa­hedral coordination geometry. The cations and ferrate anions are linked into a layered structure; the layers are connected through the uncoordinated water mol­ecules into a hydrogen-bonded three-dimensional supra­molecular structure. One of the uncoordinated water molecules is disordered around an inversion centre and was refined with half-occupancy for each position. PMID:21582387

Simultaneous in situ measurements and diurnal variations of NO, NO2, O3, jNO2, CH4, H2O, and CO2 in the 40- to 26-km region using an open path tunable diode laser spectrometer

NASA Technical Reports Server (NTRS)

Webster, Christopher R.; May, Randy D.

1987-01-01

Simultaneous in situ measurements of temperature, pressure, and the NO, NO2, O3, jNO2, CH4, H2O, and CO2 concentrations were conducted in the 40- to 26-km region of the stratosphere using the JPL Balloon-borne Laser In Situ Sensor, a tunable diode laser absorption spectrometer. The NO, NO2, CH4, H2O, and CO2 concentration measurements generally show good agreement with previous observations, with a tendency for somewhat lower NO2 amounts. Measured O3 concentrations at 38 km agree well with comparable measurements from in situ UV photometers, but at 28 km they are lower by about 10 percent and agree more closely with the solar backscattered UV data. A decline was found in NO2 during the night over a 5-km altitude range, which implies either lower NO2 postsunset profiles, or an NO2 decay rate that is significantly higher than current model predictions that use N2O5 chemistry.

Insights into the Electronic Structure of Ozone and Sulfur Dioxide from Generalized Valence Bond Theory: Bonding in O3 and SO2.

PubMed

Takeshita, Tyler Y; Lindquist, Beth A; Dunning, Thom H

2015-07-16

There are many well-known differences in the physical and chemical properties of ozone (O3) and sulfur dioxide (SO2). O3 has longer and weaker bonds than O2, whereas SO2 has shorter and stronger bonds than SO. The O-O2 bond is dramatically weaker than the O-SO bond, and the singlet-triplet gap in SO2 is more than double that in O3. In addition, O3 is a very reactive species, while SO2 is far less so. These disparities have been attributed to variations in the amount of diradical character in the two molecules. In this work, we use generalized valence bond (GVB) theory to characterize the electronic structure of ozone and sulfur dioxide, showing O3 does indeed possess significant diradical character, whereas SO2 is effectively a closed shell molecule. The GVB results provide critical insights into the genesis of the observed difference in these two isoelectronic species. SO2 possesses a recoupled pair bond dyad in the a"(π) system, resulting in SO double bonds. The π system of O3, on the other hand, has a lone pair on the central oxygen atom plus a pair of electrons in orbitals on the terminal oxygen atoms that give rise to a relatively weak π interaction.

Nqrs Data for H4I3Li2NO9 [H4INO3·2(ILiO3)] (Subst. No. 2278)

NASA Astrophysics Data System (ADS)

Chihara, H.; Nakamura, N.

This document is part of Subvolume B 'Substances Containing C10H16 … Zn' of Volume 48 'Nuclear Quadrupole Resonance Spectroscopy Data' of Landolt-Börnstein - Group III 'Condensed Matter'. It contains an extract of Section '3.2 Data tables' of the Chapter '3 Nuclear quadrupole resonance data' providing the NQRS data for H4I3Li2NO9 [H4INO3·2(ILiO3)] (Subst. No. 2278)

DEPOSITION VELOCITIES OF SO2 AND O3 OVER AGRICULTURAL AND FOREST ECOSYSTEMS

EPA Science Inventory

The results of field studies that measured the flux and deposition velocity of SO2 and O3 are reported. Three of the studies were over agricultural crops (pasture, corn, and soybean), and two were over forest (a deciduous forest and a mixed coniferous - deciduous forest). In al...

Solid state reactions of CeO 2, PuO 2, (U,Ce)O 2 and (U,Pu)O 2 with K 2S 2O 8

NASA Astrophysics Data System (ADS)

Keskar, Meera; Kasar, U. M.; Mudher, K. D. Singh; Venugopal, V.

2004-09-01

Solid state reactions of CeO 2, PuO 2 and mixed oxides (U,Ce)O 2 and (U,Pu)O 2 containing different mol.% of Ce and Pu, were carried out with K 2S 2O 8 at different temperatures to identify the formation of various products and to investigate their dissolution behaviour. X-ray, chemical and thermal analysis methods were used to characterise the products formed at various temperatures. The products obtained by heating two moles of K 2S 2O 8 with one mole each of CeO 2, PuO 2, (U,Ce)O 2 and (U,Pu)O 2 at 400 °C were identified as K 4Ce(SO 4) 4, K 4Pu(SO 4) 4, K 4(U,Ce)(SO 4) 4 and K 4(U,Pu)(SO 4) 4, respectively. K 4Ce(SO 4) 4 further decomposed to form K 4Ce(SO 4) 3.5 at 600 °C and mixture of K 2SO 4 and CeO 2 at 950 °C. Thus the products formed during the reaction of 2K 2S 2O 8 + CeO 2 show that cerium undergoes changes in oxidation state from +4 to +3 and again to +4. XRD data of K 4Ce(SO 4) 4 and K 4Ce(SO 4) 3.5 were indexed on triclinic and monoclinic system, respectively. PuO 2 + 2K 2S 2O 8 reacts at 400 °C to form K 4Pu(SO 4) 4 which was stable upto 750 °C and further decomposes to form K 2SO 4 + PuO 2 at 1000 °C. The products formed at 400 °C during the reactions of the oxides and mixed oxides were found to be readily soluble in 1-2 M HNO 3.

Dilution and permeation standards for the generation of NO, NO2 and SO2 calibration gas mixtures

NASA Astrophysics Data System (ADS)

Haerri, H.-P.; Macé, T.; Waldén, J.; Pascale, C.; Niederhauser, B.; Wirtz, K.; Stovcik, V.; Sutour, C.; Couette, J.; Waldén, T.

2017-03-01

The evaluation results of the metrological performance of a dilution and a permeation standard for generating SI-traceable calibration gas mixtures of NO, SO2 and NO2 for ambient air measurements are presented. The composition of the in situ produced reference gas mixtures is calculated from the instantaneous values of the input quantities of the generating standards. In a measurement comparison, the calibration and measurement capabilities of five laboratories were evaluated for the three analytes at limiting amount of substance fractions in ambient air between 20 and 150 nmol mol-1. For the upper generated reference values the target relative uncertainties of  ⩽2% (for NO and SO2) and  ⩽3% (for NO2) for evaluating the laboratory results were fulfilled in 12 out of 13 cases. For the analytical results seven out of nine laboratories met the criteria for the upper values for NO and NO2, for SO2 it was one out of four. From the negative degrees of equivalence of all NO2 comparison results it was supposed that the permeation rate of NO2 through the FEP polymer membrane of the permeator was different in air and N2. Subsequent precision permeation measurements with various carrier gases revealed that the permeation rate of NO2 was  ≈0.8% lower in synthetic air compared to N2. With the corrected NO2 reference values for air the degrees of equivalence of the laboratory results were improved and closer to be symmetrically distributed.

2D Hybrid Nanomaterials for Selective Detection of NO2 and SO2 Using "Light On and Off" Strategy.

PubMed

Chen, Aimin; Liu, Rui; Peng, Xiao; Chen, Qiaofen; Wu, Jianmin

2017-10-25

In order to distinguish NO 2 and SO 2 gas with one sensor, we designed a paper chip assembled with a 2D g-C 3 N 4 /rGO stacking hybrid fabricated via a layer-by-layer self-assembly approach. The g-C 3 N 4 /rGO hybrid exhibited a remarkable photoelectric property due to the construction of a van der Waals heterostructure. For the first time, we have been able to selectively detect NO 2 and SO 2 gas using a "light on and off" strategy. Under the "light off" condition, the g-C 3 N 4 /rGO sensor exhibited a p-type semiconducting behavior with a low detection limit of 100 ppb of NO 2 , but with no response toward SO 2 . In contrast, the sensor showed n-type semiconducting behavior which could detect SO 2 at concentration as low as 2 ppm under UV light irradiation. The effective electron transfer among the 2D structure of g-C 3 N 4 and rGO nanosheets as well as highly porous structures could play an important role in gas sensing. The different sensing mechanisms at "light on and off" circumstances were also investigated in detail.

DFT study of uranyl peroxo complexes with H2O, F-, OH-, CO3(2-), and NO3(-).

PubMed

Odoh, Samuel O; Schreckenbach, Georg

2013-05-06

The structural and electronic properties of monoperoxo and diperoxo uranyl complexes with aquo, fluoride, hydroxo, carbonate, and nitrate ligands have been studied using scalar relativistic density functional theory (DFT). Only the complexes in which the peroxo ligands are coordinated to the uranyl moiety in a bidentate mode were considered. The calculated binding energies confirm that the affinity of the peroxo ligand for the uranyl group far exceeds that of the F(-), OH(-), CO3(2-), NO3(-), and H2O ligands. The formation of the monoperoxo complexes from UO2(H2O)5(2+) and HO2(-) were found to be exothermic in solution. In contrast, the formation of the monouranyl-diperoxo, UO2(O2)2X2(4-) or UO2(O2)2X(4-/3-) (where X is any of F(-), OH(-), CO3(2-), or NO3(-)), complexes were all found to be endothermic in aqueous solution. This suggests that the monoperoxo species are the terminal monouranyl peroxo complexes in solution, in agreement with recent experimental work. Overall, we find that the properties of the uranyl-peroxo complexes conform to well-known trends: the coordination of the peroxo ligand weakens the U-O(yl) bonds, stabilizes the σ(d) orbitals and causes a mixing between the uranyl π- and peroxo σ- and π-orbitals. The weakening of the U-O(yl) bonds upon peroxide coordination results in uranyl stretching vibrational frequencies that are much lower than those obtained after the coordination of carbonato or hydroxo ligands.

Decomposition of 3,5-dinitrobenzamide in aqueous solution during UV/H2O2 and UV/TiO2 oxidation processes.

PubMed

Yan, Yingjie; Liao, Qi-Nan; Ji, Feng; Wang, Wei; Yuan, Shoujun; Hu, Zhen-Hu

2017-02-01

3,5-Dinitrobenzamide has been widely used as a feed additive to control coccidiosis in poultry, and part of the added 3,5-dinitrobenzamide is excreted into wastewater and surface water. The removal of 3,5-dinitrobenzamide from wastewater and surface water has not been reported in previous studies. Highly reactive hydroxyl radicals from UV/hydrogen peroxide (H 2 O 2 ) and UV/titanium dioxide (TiO 2 ) advanced oxidation processes (AOPs) can decompose organic contaminants efficiently. In this study, the decomposition of 3,5-dinitrobenzamide in aqueous solution during UV/H 2 O 2 and UV/TiO 2 oxidation processes was investigated. The decomposition of 3,5-dinitrobenzamide fits well with a fluence-based pseudo-first-order kinetics model. The decomposition in both two oxidation processes was affected by solution pH, and was inhibited under alkaline conditions. Inorganic anions such as NO 3 - , Cl - , SO 4 2- , HCO 3 - , and CO 3 2- inhibited the degradation of 3,5-dinitrobenzamide during the UV/H 2 O 2 and UV/TiO 2 oxidation processes. After complete decomposition in both oxidation processes, approximately 50% of 3,5-dinitrobenzamide was decomposed into organic intermediates, and the rest was mineralized to CO 2 , H 2 O, and other inorganic anions. Ions such as NH 4 + , NO 3 - , and NO 2 - were released into aqueous solution during the degradation. The primary decomposition products of 3,5-dinitrobenzamide were identified using time-of-flight mass spectrometry (LCMS-IT-TOF). Based on these products and ions release, a possible decomposition pathway of 3,5-dinitrobenzamide in both UV/H 2 O 2 and UV/TiO 2 processes was proposed.

Removal of NO in NO/N2, NO/N2/O2, NO/CH4/N2, and NO/CH4/O2/N2 systems by flowing microwave discharges.

PubMed

Hueso, José L; Gonzalez-Elipe, Agustín R; Cotrino, José; Caballero, Alfonso

2007-02-15

In this paper, continuing previous work, we report on experiments carried out to investigate the removal of NO from simulated flue gas in nonthermal plasmas. The plasma-induced decomposition of small concentrations of NO in N2 used as the carrier gas and O2 and CH4 as minority components has been studied in a surface wave discharge induced with a surfatron launcher. The reaction products and efficiency have been monitored by mass spectrometry as a function of the composition of the mixture. NO is effectively decomposed into N2 and O2 even in the presence of O2, provided always that enough CH4 is also present in the mixture. Other majority products of the plasma reactions under these conditions are NH3, CO, and H2. In the absence of O2, decomposition of NO also occurs, although in that case HCN accompanies the other reaction products as a majority component. The plasma for the different reaction mixtures has been characterized by optical emission spectroscopy. Intermediate excited species of NO*, C*, CN*, NH*, and CH* have been monitored depending on the gas mixture. The type of species detected and their evolution with the gas composition are in agreement with the reaction products detected in each case. The observations by mass spectrometry and optical emission spectroscopy are in agreement with the kinetic reaction models available in literature for simple plasma reactions in simple reaction mixtures.

Effect of substituent groups (R= sbnd CH3, sbnd Br and sbnd CF3) on the structure, stability and redox property of [Cr(R-pic)2(H2O)2]NO3·H2O complexes

NASA Astrophysics Data System (ADS)

Chai, Jie; Liu, Yanfei; Liu, Bin; Yang, Binsheng

2017-12-01

Complexes [Cr(3-CH3-pic)2(H2O)2]NO3·H2O (1), [Cr(5-Br-pic)2(H2O)2]NO3·H2O (2) and [Cr(5-CF3-pic)2(H2O)2]NO3·H2O (3) were synthesized (pic = pyridine-2-carboxylic acid) and characterized by X-ray crystal diffraction. Crystal structure indicates that two bidentate ligands occupy equatorial position and two H2O occupy axial positions in trans-configuration. (i) Decomposition of complexes 1, 2 and 3 in different medium (phosphate buffered saline (PBS), apo-ovotransferrin (apootf) and EDTA) indicates that decomposition rate constants of these complexes follow the sequence of 1 < 2 < 3. (ii) The redox potential of Cr(III)/Cr(II) by cyclic voltammetry follows the sequence of 1 (-1.20 V) > 3 (-1.29 V) > 2 (-1.31 V). (iii) In addition, ·OH-generation of the new synthesized complexes was determined by Fenton-like reaction in comparison with Cr(pic)3, and it may be related to the reduction potential of the complexes. (iv) Moreover, Hammett substituent constants σp (inductive) and σm (resonance) (R = 3-CH3, 5-Br, 5-CF3) were introduced to evaluate the impact of substituent groups on the bond length and decomposition kinetics. The substituent group on the ligand has great effect on the properties of the complexes.

Microstructural Evolution of Al2O3-ZrO2 (Y2O3) Composites and its Correlation with Toughness

NASA Astrophysics Data System (ADS)

Kim, Hee Seung; Seo, Mi Young; Kim, Ik Jin

2008-02-01

The microstructure of zirconia (ZrO2) toughened alumina (Al2O3) ceramics was carefully controlled so as to obtain dense and fine-grained ceramics, thereby improving the properties and reliability of the ceramics for capillary applications in semiconductor bonding technology. Al2O3-ZrO2(Y2O3) composite was produced via Ceramic Injection Molding (CIM) technology, followed by Sinter-HIP process. Room temperature strength, hardness, Young's modulus, thermal expansion coefficient and toughness were determined, as well as surface strengthening induced by the fine grained homogenous microstructure and the thermal treatment. The changes in alumina/zirconia grain size, sintering condition and HIP treatment were found to be correlated.

Adsorption of H2O, H2, O2, CO, NO, and CO2 on graphene/g-C3N4 nanocomposite investigated by density functional theory

NASA Astrophysics Data System (ADS)

Wu, Hong-Zhang; Bandaru, Sateesh; Liu, Jin; Li, Li-Li; Wang, Zhenling

2018-02-01

Motivated by the photocatalytic reactions of small molecules on g-C3N4 by these insights, we sought to explore the adsorption of H2O and CO2 molecules on the graphene side and H2O, H2, O2, CO, NO, and CO2 molecules on the g-C3N4 side of hybrid g-C3N4/graphene nanocomposite using first-principles calculations. The atomic structure and electronic properties of hybrid g-C3N4/graphene nanocomposite is explored. The adsorption of small molecules on graphene/g-C3N4 nanocomposite is thoroughly investigated. The computational studies revels that all small molecules on graphene/g-C3N4 nanocomposite are the physisorption. The adsorption characteristics of H2O and CO2 molecules on the graphene side are similar to that on graphene. The adsorption of H2O, H2, O2, CO, NO, and CO2 molecules on the g-C3N4 side always leads to a buckle structure of graphene/g-C3N4 nanocomposite. Graphene as a substrate can significantly relax the buckle degree of g-C3N4 in g-C3N4/graphene nanocomposite.

Mineralization of Basalts in the CO2-H2O-SO2-O2 System

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schaef, Herbert T.; Horner, Jacob A.; Owen, Antionette T.

2014-05-01

Sequestering carbon dioxide (CO2) containing minor amounts of co-contaminants in geologic formations was investigated in the laboratory through the use of high pressure static experiments. Five different basalt samples were immersed in water equilibrated with supercritical CO2 containing 1wt% sulfur dioxide (SO2) and 1wt% oxygen (O2) at reservoir conditions (~100 bar, 90°C) for 49 and 98 days. Gypsum (CaSO4) was a common precipitate, occurred early as elongated blades with striations, and served as substrates for other mineral products. Bimodal pulses of water released during dehydroxylation were key indicators along with X-ray diffraction for verifying the presences of jarosite-alunite group minerals.more » Well-developed pseudocubic jarosite crystals formed surface coatings, and in some instances mixtures of natrojarosite and natroalunite aggregated into spherically shaped structures measuring 100 μm in diameter. Reaction products were also characterized using infrared spectroscopy, which indicated OH and Fe-O stretching modes. The presences of jarosite-alunite group minerals were found in the lower wavenumber region from 700–400 cm-1. A strong preferential incorporation of Fe(III) into natrojarosite was attributed to the oxidation potential of O2. Evidence of CO2 was detected during thermal decomposition of precipitates, suggesting the onset of mineral carbonation.« less

Mineralization of basalts in the CO2-H2O-SO2-O2 system.

PubMed

Schaef, Herbert T; Horner, Jake A; Owen, Antoinette T; Thompson, Chris J; Loring, John S; McGrail, Bernard P

2014-05-06

Sequestering carbon dioxide (CO2) containing minor amounts of co-contaminants in geologic formations was investigated in the laboratory through the use of high pressure static experiments. Five different basalt samples were immersed in water equilibrated with supercritical CO2 containing 1 wt % sulfur dioxide (SO2) and 1 wt % oxygen (O2) at reservoir conditions (∼ 100 bar, 90 °C) for 48 and 98 days. Gypsum (CaSO4) was a common precipitate, occurred early as elongated blades with striations, and served as substrates for other mineral products. In addition to gypsum, bimodal pulses of water released during dehydroxylation were key indicators, along with X-ray diffraction, for verifying the presence of jarosite-alunite group minerals. Well-developed pseudocubic jarosite crystals formed surface coatings, and in some instances, mixtures of natrojarosite and natroalunite aggregated into spherically shaped structures measuring 100 μm in diameter. Reaction products were also characterized using infrared spectroscopy, which indicated OH and Fe-O stretching modes. The presences of jarosite-alunite group minerals were found in the lower wavenumber region from 700 to 400 cm(-1). A strong preferential incorporation of Fe(III) into natrojarosite was attributed to the oxidation potential of O2. Evidence of CO2 was detected during thermal decomposition of precipitates, suggesting the onset of mineral carbonation.

Carbon-catalyzed oxidation of SO2 by NO2 and air

NASA Technical Reports Server (NTRS)

Rogowski, R. S.; Schryer, D. R.; Cofer, W. R., III; Edahl, R. A., Jr.; Munavalli, S.

1982-01-01

A series of experiments was performed using carbon particles (commercial furnace black) as a surrogate for soot particles. Carbon particles were suspended in water, and gas mixtures were bubbled into the suspensions to observe the effect of carbon particles on the oxidation of SO2 by air and NO2. Identical gas mixtures were bubbled into a blank containing only pure water. After exposure each solution was analyzed for pH and sulfate. It was found that NO2 greatly enhances the oxidation of SO2 to sulfate in the presence of carbon particles. The amount of sulfate found in the blanks was significantly less. Under the conditions of these experiments no saturation of the reaction was observed and SO2 was converted to sulfate even in a highly acid medium (pH or = 1.5).

One-pot chemoselective synthesis of novel pyrrole-substituted pyrido [2,3-d]pyrimidines using [γ-Fe2O3@HAp-SO3H] as an efficient nanocatalyst

NASA Astrophysics Data System (ADS)

Jahanshahi, Parivash; Mamaghani, Manouchehr; Haghbin, Fereshteh; Nia, Roghayeh Hossein; Rassa, Mehdi

2018-03-01

Novel (1-methyl-1H-pyrrol-2-yl)-[2,3-d]pyrimidine derivatives were synthesized chemoselectively in good to high yields (81-90%) and short reaction times (7-14 min) by hydroxyapatite-encapsulated-γ-Fe2O3 supported sulfonic acid ([γ-Fe2O3@HAp-SO3H]) catalyzed condensation of 3-(1-methyl-1H-pyrrol-2-yl)-3-oxopropanenitrile, 6-amino-2-(alkylthio)pyrimidin-4(3H)-one and various aromatic aldehydes. The easy work-up of the products, rapidity, high efficiency and recyclability of the catalyst are advantages of this protocol. The antibacterial activity of the newly synthesized products was investigated. Some of the products showed encouraging activity.

Photocrystallographic structure determination of a new geometric isomer of [Ru(NH3)4(H2O)(eta1-OSO)][MeC6H4SO3]2.

PubMed

Bowes, Katharine F; Cole, Jacqueline M; Husheer, Shamus L G; Raithby, Paul R; Savarese, Teresa L; Sparkes, Hazel A; Teat, Simon J; Warren, John E

2006-06-21

The structure of a new metastable geometric isomer of [Ru(NH3)4(H2O)(SO2)][MeC6H4SO3]2 in which the SO2 group is coordinated through a single oxygen in an eta1-OSO bonding mode has been determined at 13 K; the new isomer was obtained as a 36% component of the structure within a single crystal upon irradiation using a tungsten lamp.

Influence of Background H2O on the Collision-Induced Dissociation Products Generated from [UO2NO3]+

NASA Astrophysics Data System (ADS)

Van Stipdonk, Michael J.; Iacovino, Anna; Tatosian, Irena

2018-04-01

Developing a comprehensive understanding of the reactivity of uranium-containing species remains an important goal in areas ranging from the development of nuclear fuel processing methods to studies of the migration and fate of the element in the environment. Electrospray ionization (ESI) is an effective way to generate gas-phase complexes containing uranium for subsequent studies of intrinsic structure and reactivity. Recent experiments by our group have demonstrated that the relatively low levels of residual H2O in a 2-D, linear ion trap (LIT) make it possible to examine fragmentation pathways and reactions not observed in earlier studies conducted with 3-D ion traps (Van Stipdonk et al. J. Am. Soc. Mass Spectrom. 14, 1205-1214, 2003). In the present study, we revisited the dissociation of complexes composed of uranyl nitrate cation [UVIO2(NO3)]+ coordinated by alcohol ligands (methanol and ethanol) using the 2-D LIT. With relatively low levels of background H2O, collision-induced dissociation (CID) of [UVIO2(NO3)]+ primarily creates [UO2(O2)]+ by the ejection of NO. However, CID (using He as collision gas) of [UVIO2(NO3)]+ creates [UO2(H2O)]+ and UO2 + when the 2-D LIT is used with higher levels of background H2O. Based on the results presented here, we propose that product ion spectrum in the previous experiments was the result of a two-step process: initial formation of [UVIO2(O2)]+ followed by rapid exchange of O2 for H2O by ion-molecule reaction. Our experiments illustrate the impact of residual H2O in ion trap instruments on the product ions generated by CID and provide a more accurate description of the intrinsic dissociation pathway for [UVIO2(NO3)]+. [Figure not available: see fulltext.

HYDROTHERMAL SYNTHESIS OF α-MoO3 NANORODS FOR NO2 DETECTION

NASA Astrophysics Data System (ADS)

Bai, Shouli; Chen, Song; Tian, Yuan; Luo, Ruixian; Li, Dianqing; Chen, Aifan

2012-12-01

Thermodynamically stable molybdenum trioxide nanorods have been successfully synthesized by a simple hydrothermal process. The product exhibits high-quality, single-crystalline layered orthorhombic structure (α-MoO3), and aspect ratio over 20 by characterizations of X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HR-TEM) and Fourier transform infrared (FT-IR). The growth mechanism of α-MoO3 nanorods can be understood by electroneutral and dehydration reaction, which is highly dependent on solution acidity and hydrothermal temperature. The sensing tests show that the sensor based on MoO3 nanorods exhibits high sensitivity to NO2 and is not interferred by CO and CH4, which makes this kind sensor a competitive candidate for NO2 detection. The intrinsic sensing performance of MoO3 maybe arise from its nonstoichiometry of MoO3 owing to the presence of Mo5+ and oxygen vacancy in MoO3 lattice, which has been confirmed by X-ray photoelectron spectroscopy (XPS) analysis. The sensing mechanism of MoO3 for NO2 is also discussed.

Interaction mechanisms between α-Fe2O3, γ-Fe2O3 and Fe3O4 nanoparticles and Citrus maxima seedlings.

PubMed

Li, Junli; Hu, Jing; Xiao, Lian; Wang, Yunqiang; Wang, Xilong

2018-06-01

The interactions between α-Fe 2 O 3 , γ-Fe 2 O 3 , and Fe 3 O 4 nanoparticles (NPs) and Citrus maxima seedlings were examined so as to better understand possible particle applications as an Fe source for crop plants. NPs toxicity to the exposed plant was investigated as well. The α- and γ-Fe 2 O 3 NPs were accumulated by plant root cells through diapirism and endocytosis, respectively, but translocation to the shoots was negligible. Analysis of malondialdehyde (MDA), soluble protein content, and antioxidant enzyme activity revealed that Fe deficiency induced strong oxidative stress in Citrus maxima seedlings, which followed an order of Fe deficiency>Fe 3+ >α-Fe 2 O 3 , γ-Fe 2 O 3 NPs>Fe 3 O 4 NPs. However, the chlorophyll leaf content of plants exposed to α-Fe 2 O 3 , γ-Fe 2 O 3 , Fe 3 O 4 NPs and Fe 3+ were significantly reduced by 31.1%, 14.8%, 18.8% and 22.0%, respectively, relative to the control. Furthermore, RT-PCR analysis revealed no up-regulation of AHA and Nramp3 genes in Citrus maxima roots; however, the relative FRO2 gene expression upon exposure to iron oxide NPs was 1.4-2.8-fold higher than the control. Ferric reductase activity was consistently enhanced upon iron oxide NPs exposure. These findings advance understanding of the interaction mechanisms between metal oxide NPs and plants, and provide important knowledge need for the possible application of these materials in agriculture. Copyright © 2017 Elsevier B.V. All rights reserved.

Detection of interstellar N2O: A new molecule containing an N-O bond

NASA Astrophysics Data System (ADS)

Ziurys, L. M.; Apponi, A. J.; Hollis, J. M.; Snyder, L. E.

1994-12-01

A new interstellar molecule, N2O, known as nitrous oxide or 'laughing gas,' has been detected using the NRAO 12 m telescope. The J = 3 - 2, 4 - 3, 5 - 4, and 6 - 5 rotational transitions of this species at 75, 100, 125, and 150 GHz, respectively, were observed toward Sgr B2(M). The column density derived for N2O in this source is Ntot approx. 1015/sq. cm, which corresponds to a fractional abundance of approx. 10-9, relative to H2. This value implies abundance ratios of N2O/NO approx. 0.1 and N2O/HNO approx. 3 in the Galactic center. Such ratios are in excellent agreement with predictions of ion-molecule models of interstellar chemistry using early-time calculations and primarily neutral-neutral reactions. N2O is the third interstellar molecule detected thus far containing an N-O bond. Such bonds cannot be so rare as previously thought.

Detection of interstellar N2O: A new molecule containing an N-O bond

NASA Technical Reports Server (NTRS)

Ziurys, L. M.; Apponi, A. J.; Hollis, J. M.; Snyder, L. E.

1994-01-01

A new interstellar molecule, N2O, known as nitrous oxide or 'laughing gas,' has been detected using the NRAO 12 m telescope. The J = 3 - 2, 4 - 3, 5 - 4, and 6 - 5 rotational transitions of this species at 75, 100, 125, and 150 GHz, respectively, were observed toward Sgr B2(M). The column density derived for N2O in this source is N(sub tot) approx. 10(exp 15)/sq. cm, which corresponds to a fractional abundance of approx. 10(exp -9), relative to H2. This value implies abundance ratios of N2O/NO approx. 0.1 and N2O/HNO approx. 3 in the Galactic center. Such ratios are in excellent agreement with predictions of ion-molecule models of interstellar chemistry using early-time calculations and primarily neutral-neutral reactions. N2O is the third interstellar molecule detected thus far containing an N-O bond. Such bonds cannot be so rare as previously thought.

Hydrogen bonding in goldichite, KFe(SO4)2ṡ4H2O: structure refinement

NASA Astrophysics Data System (ADS)

Yang, Zhuming; Giester, Gerald

2018-02-01

The crystal structure of goldichite KFe(SO4)2ṡ4H2O was determined on a single crystal from the Baiyinchang copper deposit, Gansu, China. [ P121/ c1, a = 10.395(2), b = 10.475(2), c = 9.0875(18) Å, β = 101.65(3)°, V = 969.1(3) Å3, Z = 4]. All non-H atoms were refined with anisotropic displacement parameters and positions of H-atoms were determined by difference Fourier methods and refined from X-ray diffraction data. The crystal structure of goldichite consists of corrugated sheets parallel to the (100) plane by sharing corners between FeO6 octahedra and SO4 tetrahedra. The interstitial potassium atom exhibits a [KO7(H2O)2] nine-fold coordination, which shares edges to form a column parallel to the c-axis and to build a slab with the corrugated sheet. These slabs are linked in the [100] direction through a network of hydrogen bonds. Three types of hydrogen bonds involve links of slabs: Ow(3)-H(3B)···O(1), Ow(6)-H(6B)···O(11) and Ow(9)-H(9B)···O(11). The FTIR spectrum of goldichite shows a strong absorption between 3384 cm-1 and 3592 cm-1, which is in accordance with the O-H···O distances derived from structure data.

Comparative study of three magnetic nano-particles (FeSO4, FeSO4/SiO2, FeSO4/SiO2/TiO2) in plasmid DNA extraction.

PubMed

Rahnama, H; Sattarzadeh, A; Kazemi, F; Ahmadi, N; Sanjarian, F; Zand, Z

2016-11-15

Recent updates on Magnetic Nano-Particles (MNPs) based separation of nucleic acids have received more attention due to their easy manipulation, simplicity, ease of automation and cost-effectiveness. It has been indicated that DNA molecules absorb on solid surfaces via hydrogen-bonding, and hydrophobic and electrostatic interactions. These properties highly depend on the surface condition of the solid support. Therefore, surface modification of MNPs may enhance their functionality and specification. In the present study, we functionalized Fe3O4 nano-particle surface utilizing SiO2 and TiO2 layer as Fe3O4/SiO2 and Fe3O4/SiO2/TiO2 and then compare their functionality in the adsorption of plasmid DNA molecules with the naked Fe3O4 nano-particles. The result obtained showed that the purity and amount of DNA extracted by Fe3O4 coated by SiO2 or SiO2/TiO2 were higher than the naked Fe3O4 nano-particles. Furthermore, we obtained pH 8 and 1.5 M NaCl as an optimal condition for desorption of DNA from MNPs. The result further showed that, 0.2 mg nano-particle and 10 min at 55 °C are the optimal conditions for DNA desorption from nano-particles. In conclusion, we recommended Fe3O4/SiO2/TiO2 as a new MNP for separation of DNA molecules from biological sources. Copyright © 2016 Elsevier Inc. All rights reserved.

Uptake of CO2, SO2, HNO3 and HCl on calcite (CaCO3) at 300 K: mechanism and the role of adsorbed water.

PubMed

Santschi, Ch; Rossi, M J

2006-06-01

All experimental observations of the uptake of the four title compounds on calcite are consistent with the presence of a reactive bifunctional surface intermediate Ca(OH)(HCO3) that has been proposed in the literature. The uptake of CO2 and SO2 occurs on specific adsorption sites of crystalline CaCO3(s) rather than by dissolution in adsorbed water, H2O(ads). SO2 primarily interacts with the bicarbonate moiety whereas CO2, HNO3 and HCl all react first with the hydroxyl group of the surface intermediate. Subsequently, the latter two react with the bicarbonate group to presumably form Ca(NO3)2 and CaCl2.2H2O. The effective equilibrium constant of the interaction of CO2 with calcite in the presence of H2O(ads) is kappa = deltaCO2/(H2O(ads)[CO2]) = 1.62 x 10(3) bar(-1), where CO2 is the quantity of CO2 adsorbed on CaCO3. The reaction mechanism involves a weakly bound precursor species that is reversibly adsorbed and undergoes rate-controlling concurrent reactions with both functionalities of the surface intermediate. The initial uptake coefficients gamma0 on calcite powder depend on the abundance of H2O(ads) under the present experimental conditions and are on the order of 10(-4) for CO2 and 0.1 for SO2, HNO3 and HCl, with gamma(ss) being significantly smaller than gamma0 for HNO3 and HCl, thus indicating partial saturation of the uptake. At 33% relative humidity and 300 K there are 3.5 layers of H2O adsorbed on calcite that reduce to a fraction of a monolayer of weakly and strongly bound water upon pumping and/or heating.

SO3 formation from the X-ray photolysis of SO2 astrophysical ice analogues: FTIR spectroscopy and thermodynamic investigations.

PubMed

de Souza Bonfim, Víctor; Barbosa de Castilho, Roberto; Baptista, Leonardo; Pilling, Sergio

2017-10-11

In this combined experimental-theoretical work we focus on the physical and chemical changes induced by soft X-rays on sulfur dioxide (SO 2 ) ice at a very low temperature, in an attempt to clarify and quantify its survival and chemical changes in some astrophysical environments. SO 2 is an important constituent of some Jupiter moons and has also been observed in ices around protostars. The measurements were performed at the Brazilian Synchrotron Light Source (LNLS/CNPEM), in Campinas, Brazil. The SO 2 ice sample (12 K) was exposed to a broadband beam of mainly soft X-rays (6-2000 eV) and in situ analyses were performed by IR spectroscopy. The X-ray photodesorption yield (upper limit) was around 0.25 molecules per photon. The values determined for the effective destruction (SO 2 ) and formation (SO 3 ) cross sections were 2.5 × 10 -18 cm 2 and 2.1 × 10 -18 cm 2 , respectively. The chemical equilibrium (88% of SO 2 and 12% of SO 3 ) was reached after the fluence of 1.6 × 10 18 photons cm -2 . The SO 3 formation channels were studied at the second-order Møller-Plesset perturbation theory (MP2) level, which showed the three most favorable reaction routes (ΔH < -79 kcal mol -1 ) in simulated SO 2 ice: (i) SO + O 2 → SO 3 , (ii) SO 2 + O → SO 3 , and (iii) SO 2 + O + → SO 3 + + e - → SO 3 . The amorphous solid environment effect decreases the reactivity of intermediate species towards SO 3 formation, and ionic species are even more affected. The experimentally determined effective cross sections and theoretical reaction channels identified in this work allow us to better understand the chemical evolution of certain sulfur-rich astrophysical environments.

Densities and apparent molar volumes of atmospherically important electrolyte solutions. 2. The systems H(+)-HSO4(-)-SO4(2-)-H2O from 0 to 3 mol kg(-1) as a function of temperature and H(+)-NH4(+)-HSO4(-)-SO4)2-)-H2O from 0 to 6 mol kg(-1) at 25 °C using a Pitzer ion interaction model, and NH4HSO4-H2O and (NH4)3H(SO4)2-H2O over the entire concentration range.

PubMed

Clegg, S L; Wexler, A S

2011-04-21

A Pitzer ion interaction model has been applied to the systems H(2)SO(4)-H(2)O (0-3 mol kg(-1), 0-55 °C) and H(2)SO(4)-(NH(4))(2)SO(4)-H(2)O (0-6 mol kg(-1), 25 °C) for the calculation of apparent molar volume and density. The dissociation reaction HSO(4)(-)((aq)) ↔ H(+)((aq)) + SO(4)(2-)((aq)) is treated explicitly. Apparent molar volumes of the SO(4)(2-) ion at infinite dilution were obtained from part 1 of this work, (1) and the value for the bisulfate ion was determined in this study from 0 to 55 °C. In dilute solutions of both systems, the change in the degree of dissociation of the HSO(4)(-) ion with concentration results in much larger variations of the apparent molar volumes of the solutes than for conventional strong (fully dissociated) electrolytes. Densities and apparent molar volumes are tabulated. Apparent molar volumes calculated using the model are combined with other data for the solutes NH(4)HSO(4) and (NH(4))(3)H(SO(4))(2) at 25 °C to obtain apparent molar volumes and densities over the entire concentration range (including solutions supersaturated with respect to the salts).